Prediction of the thermophysical properties of molten salt fast reactor fuel from first-principles

NASA Astrophysics Data System (ADS)

Gheribi, A. E.; Corradini, D.; Dewan, L.; Chartrand, P.; Simon, C.; Madden, P. A.; Salanne, M.

2014-05-01

Molten fluorides are known to show favourable thermophysical properties which make them good candidate coolants for nuclear fission reactors. Here we investigate the special case of mixtures of lithium fluoride and thorium fluoride, which act both as coolant and as fuel in the molten salt fast reactor concept. By using ab initio parameterised polarisable force fields, we show that it is possible to calculate the whole set of properties (density, thermal expansion, heat capacity, viscosity and thermal conductivity) which are necessary for assessing the heat transfer performance of the melt over the whole range of compositions and temperatures. We then deduce from our calculations several figures of merit which are important in helping the optimisation of the design of molten salt fast reactors.

Association between salt and hypertension in rural and urban populations of low to middle income countries: a systematic review and meta-analysis of population based studies.

PubMed

Subasinghe, Asvini K; Arabshahi, Simin; Busingye, Doreen; Evans, Roger G; Walker, Karen Z; Riddell, Michaela A; Thrift, Amanda G

2016-01-01

The prevalence of hypertension, the greatest contributor to mortality globally, is increasing in low-and-middle income countries (LMICs). In urban regions of LMICs, excessive salt intake is associated with increased risk of hypertension. We aimed to determine whether this is the case in rural regions as well. We performed a meta-analysis of studies in rural and urban areas of LMICs in which the association of salt and hypertension were assessed using multivariable models. We identified 18 studies with a total of 134,916 participants. The prevalence of high salt intake ranged from 21.3% to 89.5% in rural and urban populations. When salt was analysed as a continuous variable, a greater impact of salt on hypertension was found in urban (n=4) (pooled effect size (ES) 1.42, 95% CI 1.19, 1.69) than in rural populations (n=4) (pooled ES 1.07, 95% CI 1.04, 1.10, p for difference <0.001). In studies where salt was analysed continuously, a greater impact of salt on hypertension was observed in lean rural populations (BMI <23 kg/m2) than in non-lean rural populations (BMI >=23 kg/m2, p for difference <0.001). The prevalence of high salt intake is similar in rural and urban regions. Excessive salt intake has a greater impact on the prevalence of hypertension in urban than rural regions. BMI appears to modify the relationship between salt and hypertension in rural populations.

Aggregation in charged nanoparticles solutions induced by different interactions

NASA Astrophysics Data System (ADS)

Abbas, S.; Kumar, Sugam; Aswal, V. K.; Kohlbrecher, J.

2016-05-01

Small-angle neutron scattering (SANS) has been used to study the aggregation of anionic silica nanoparticles as induced through different interactions. The nanoparticle aggregation is induced by addition of salt (NaCl), cationic protein (lysozyme) and non-ionic surfactant (C12E10) employing different kind of interactions. The results show that the interaction in presence of salt can be explained using DLVO theory whereas non-DLVO forces play important role for interaction of nanoparticles with protein and surfactant. The presence of salt screens the repulsion between charged nanoparticles giving rise to a net attraction in the DLVO potential. On the other hand, strong electrostatic attraction between nanoparticle and oppositely charged protein leads to protein-mediated nanoparticle aggregation. In case of non-ionic surfactant, the relatively long-range attractive depletion interaction is found to be responsible for the particle aggregation. Interestingly, the completely different interactions lead to similar kind of aggregate morphology. The nanoparticle aggregates formed are found to have mass fractal nature having a fractal dimension (~2.5) consistent with diffusion limited type of fractal morphology in all three cases.

Aggregation in charged nanoparticles solutions induced by different interactions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Abbas, S.; Kumar, Sugam; Aswal, V. K., E-mail: vkaswal@barc.gov.in

2016-05-23

Small-angle neutron scattering (SANS) has been used to study the aggregation of anionic silica nanoparticles as induced through different interactions. The nanoparticle aggregation is induced by addition of salt (NaCl), cationic protein (lysozyme) and non-ionic surfactant (C12E10) employing different kind of interactions. The results show that the interaction in presence of salt can be explained using DLVO theory whereas non-DLVO forces play important role for interaction of nanoparticles with protein and surfactant. The presence of salt screens the repulsion between charged nanoparticles giving rise to a net attraction in the DLVO potential. On the other hand, strong electrostatic attraction betweenmore » nanoparticle and oppositely charged protein leads to protein-mediated nanoparticle aggregation. In case of non-ionic surfactant, the relatively long-range attractive depletion interaction is found to be responsible for the particle aggregation. Interestingly, the completely different interactions lead to similar kind of aggregate morphology. The nanoparticle aggregates formed are found to have mass fractal nature having a fractal dimension (~2.5) consistent with diffusion limited type of fractal morphology in all three cases.« less

Intermediate-range Nuclear Forces (INF) negotiations and treaty: An historical case study. Master's thesis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wussler, D.E.

1989-09-01

This thesis performs detailed analysis of the Intermediate Range Nuclear Forces (INF) negotiations and treaty and compares them with those of the two Strategic Arms Limitations Talks (SALT). The study's objectives were: describe SALT and INF negotiations and the contents of the treaties; analyze US and Soviet goals and strategies during the INF negotiations; determine which goals were or were not attained by both sides, and ascertain reasons for this; and delineate arms control progress and prospects since INF Treaty ratification. The study found that the two SALT treaties did impose ceilings in certain areas of strategic weapons but didmore » not curtail the arms race. Treaty verification methods were criticized as being lax. The US achieved the major goal of ridding Europe of the Soviet SS-20 missile. It had to deploy missiles of its own to make the USSR realize the seriousness of its resolve. The US had total support from NATO in achieving this goal. However, with INF gone, the European conventional forces imbalance looms larger, and the West is fighting to obtain asymmetric conventional cuts.« less

Ammonium chloride salting out extraction/cleanup for trace-level quantitative analysis in food and biological matrices by flow injection tandem mass spectrometry.

PubMed

Nanita, Sergio C; Padivitage, Nilusha L T

2013-03-20

A sample extraction and purification procedure that uses ammonium-salt-induced acetonitrile/water phase separation was developed and demonstrated to be compatible with the recently reported method for pesticide residue analysis based on fast extraction and dilution flow injection mass spectrometry (FED-FI-MS). The ammonium salts evaluated were chloride, acetate, formate, carbonate, and sulfate. A mixture of NaCl and MgSO4, salts used in the well-known QuEChERS method, was also tested for comparison. With thermal decomposition/evaporation temperature of <350°C, ammonium salts resulted in negligible ion source residual under typical electrospray conditions, leading to consistent method performance and less instrument cleaning. Although all ammonium salts tested induced acetonitrile/water phase separation, NH4Cl yielded the best performance, thus it was the preferred salting out agent. The NH4Cl salting out method was successfully coupled with FI/MS/MS and tested for fourteen pesticide active ingredients: chlorantraniliprole, cyantraniliprole, chlorimuron ethyl, oxamyl, methomyl, sulfometuron methyl, chlorsulfuron, triflusulfuron methyl, azimsulfuron, flupyrsulfuron methyl, aminocyclopyrachlor, aminocyclopyrachlor methyl, diuron and hexazinone. A validation study was conducted with nine complex matrices: sorghum, rice, grapefruit, canola, milk, eggs, beef, urine and blood plasma. The method is applicable to all analytes, except aminocyclopyrachlor. The method was deemed appropriate for quantitative analysis in 114 out of 126 analyte/matrix cases tested (applicability rate=0.90). The NH4Cl salting out extraction/cleanup allowed expansion of FI/MS/MS for analysis in food of plant and animal origin, and body fluids with increased ruggedness and sensitivity, while maintaining high-throughput (run time=30s/sample). Limits of quantitation (LOQs) of 0.01mgkg(-1) (ppm), the 'well-accepted standard' in pesticide residue analysis, were achieved in >80% of cases tested; while limits of detection (LODs) were typically in the range of 0.001-0.01mgkg(-1) (ppm). A comparison to a well-established HPLC/MS/MS method was also conducted, yielding comparable results, thus confirming the suitability of NH4Cl salting out FI/MS/MS for pesticide residue analysis. Copyright © 2013 Elsevier B.V. All rights reserved.

Salting-out assisted liquid-liquid extraction coupled to ultra-high performance liquid chromatography-tandem mass spectrometry for the determination of tetracycline residues in infant foods.

PubMed

Moreno-González, David; García-Campaña, Ana M

2017-04-15

The use of salting-out assisted liquid-liquid extraction (SALLE) combined with ultra-high performance liquid chromatography tandem mass spectrometry (UHPLC-MS/MS) has been evaluated for the determination of tetracyclines in infant foods based on meat and vegetables or in milk. To obtain satisfactory extraction efficiencies for the studied analytes, several parameters affecting the SALLE procedure were optimized. Analytical performances of the method were satisfactory, obtaining limits of quantification lower than 0.48μgkg -1 in all cases. The precision, expressed as relative standard deviation (%, RSD) was below 11.3%. The extraction efficiency for fortified samples ranged from 89.2 to 96.8%, with RSDs lower than 7.3%. Matrix effect was evaluated for all samples studied, being lower than |21|% in all cases. In relation to the low solvent consumption, the proposed methodology could be considered rapid, cheap and environmentally friendly. Its applicability has been successfully tested in a wide range of infant foods. Copyright © 2016 Elsevier Ltd. All rights reserved.

The effect on human salivary fluoride concentration of consuming fluoridated salt-containing baked food items.

PubMed

Macpherson, L M; Stephen, K W

2001-10-01

Salt fluoridation is recognised world-wide as a proven and viable alternative means of consumer choice-related, community-based fluoridation where water fluoridation is either technically or politically impossible. However, as most salt consumed is contained within cooked food products, rather than sprinkled over prepared food at the table, the purpose of this study was to investigate the effects on salivary fluoride concentration of consuming baked food products prepared with 250 and 350 ppm fluoridated salt (as KF). Six food items were baked with (a) normal non-fluoridated salt, (b) 250 mg F/kg salt and (c) 350 mg F/kg salt. Eleven adult volunteers consumed these foodstuffs on separate occasions and salivary samples were collected for fluoride analyses before and at various time points (1-30 min) after eating. For most foodstuffs, small but significant increases in salivary fluoride concentration occurred for at least 5 min after ingestion of the fluoridated salt-containing items. Salivary fluoride concentrations peaked 1 or 2 min after eating, with highest values for the six test foods ranging from 0.16 to 0.25 ppm F, and from 0.18 to 0.44 ppm F for the 250 and 350 mg F/kg salt products, respectively. In all cases, salivary fluoride concentrations had returned to baseline by 20 min. The clinical significance of such small, short-term increases in salivary fluoride is uncertain, but the findings suggest that a more frequent intake of foods with fluoridated salt substituted for normal salt could help sustain slightly elevated salivary fluoride concentrations for more prolonged periods of the day, and might thus potentiate the cariostatic effects of saliva on tooth mineral.

Analysis of Shigella flexneri Resistance, Biofilm Formation, and Transcriptional Profile in Response to Bile Salts

PubMed Central

Nickerson, Kourtney P.; Chanin, Rachael B.; Sistrunk, Jeticia R.; Fink, Peter J.; Barry, Eileen M.; Nataro, James P.

2017-01-01

ABSTRACT The Shigella species cause millions of cases of watery or bloody diarrhea each year, mostly in children in developing countries. While many aspects of Shigella colonic cell invasion are known, crucial gaps in knowledge regarding how the bacteria survive, transit, and regulate gene expression prior to infection remain. In this study, we define mechanisms of resistance to bile salts and build on previous research highlighting induced virulence in Shigella flexneri strain 2457T following exposure to bile salts. Typical growth patterns were observed within the physiological range of bile salts; however, growth was inhibited at higher concentrations. Interestingly, extended periods of exposure to bile salts led to biofilm formation, a conserved phenotype that we observed among members of the Enterobacteriaceae. Characterization of S. flexneri 2457T biofilms determined that both bile salts and glucose were required for formation, dispersion was dependent upon bile salts depletion, and recovered bacteria displayed induced adherence to HT-29 cells. RNA-sequencing analysis verified an important bile salt transcriptional profile in S. flexneri 2457T, including induced drug resistance and virulence gene expression. Finally, functional mutagenesis identified the importance of the AcrAB efflux pump and lipopolysaccharide O-antigen synthesis for bile salt resistance. Our data demonstrate that S. flexneri 2457T employs multiple mechanisms to survive exposure to bile salts, which may have important implications for multidrug resistance. Furthermore, our work confirms that bile salts are important physiological signals to activate S. flexneri 2457T virulence. This work provides insights into how exposure to bile likely regulates Shigella survival and virulence during host transit and subsequent colonic infection. PMID:28348056

Temperature invariance of NaCl solubility in water: inferences from salt-water cluster behavior of NaCl, KCl, and NH4Cl.

PubMed

Bharmoria, Pankaj; Gupta, Hariom; Mohandas, V P; Ghosh, Pushpito K; Kumar, Arvind

2012-09-27

The growth and stability of salt-water clusters have been experimentally studied in aqueous solutions of NaCl, KCl, and NH(4)Cl from dilute to near-saturation conditions employing dynamic light scattering and zeta potential measurements. In order to examine cluster stability, the changes in the cluster sizes were monitored as a function of temperature. Compared to the other cases, the average size of NaCl-water clusters remained almost constant over the studied temperature range of 20-70 °C. Information obtained from the temperature-dependent solution compressibility (determined from speed of sound and density measurements), multinuclear NMR ((1)H, (17)O, (35)Cl NMR), and FTIR were utilized to explain the cluster behavior. Comparison of NMR chemical shifts of saturated salt solutions with solid-state NMR data of pure salts, and evaluation of spectral modifications in the OH stretch region of saturated salt solutions as compared to that of pure water, provided important clues on ion pair-water interactions and water structure in the clusters. The high stability and temperature independence of the cluster sizes in aqueous NaCl shed light on the temperature invariance of its solubility.

Examination of Liquid Fluoride Salt Heat Transfer

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yoder Jr, Graydon L

2014-01-01

The need for high efficiency power conversion and energy transport systems is increasing as world energy use continues to increase, petroleum supplies decrease, and global warming concerns become more prevalent. There are few heat transport fluids capable of operating above about 600oC that do not require operation at extremely high pressures. Liquid fluoride salts are an exception to that limitation. Fluoride salts have very high boiling points, can operate at high temperatures and low pressures and have very good heat transfer properties. They have been proposed as coolants for next generation fission reactor systems, as coolants for fusion reactor blankets,more » and as thermal storage media for solar power systems. In each case, these salts are used to either extract or deliver heat through heat exchange equipment, and in order to design this equipment, liquid salt heat transfer must be predicted. This paper discusses the heat transfer characteristics of liquid fluoride salts. Historically, heat transfer in fluoride salts has been assumed to be consistent with that of conventional fluids (air, water, etc.), and correlations used for predicting heat transfer performance of all fluoride salts have been the same or similar to those used for water conventional fluids an, water, etc). A review of existing liquid salt heat transfer data is presented, summarized, and evaluated on a consistent basis. Less than 10 experimental data sets have been found in the literature, with varying degrees of experimental detail and measured parameters provided. The data has been digitized and a limited database has been assembled and compared to existing heat transfer correlations. Results vary as well, with some data sets following traditional correlations; in others the comparisons are less conclusive. This is especially the case for less common salt/materials combinations, and suggests that additional heat transfer data may be needed when using specific salt eutectics in heat transfer equipment designs. All of the data discussed above were taken under forced convective conditions (both laminar and turbulent). Some recent data taken at ORNL under free convection conditions are also presented and results discussed. This data was taken using a simple crucible experiment with an instrumented nickel heater inserted in the salt to induce natural circulation within the crucible. The data was taken over a temperature range of 550oC to 650oC in FLiNaK salt. This data covers both laminar and turbulent natural convection conditions, and is compared to existing forms of natural circulation correlations.« less

Snack foods and dental caries. Investigations using laboratory animals.

PubMed

Grenby, T H

1990-05-05

The nation's eating habits are undergoing major transformation, with a swing away from traditional meals to a huge increase in snack consumption, but very little is known of the nutritional and dental implications of this change. The research project reported here evaluated a range of snack foods in caries-active laboratory animals, comparing them, as dietary ingredients, with noncariogenic and cariogenic (sugar) diets. The findings showed the very low cariogenicity of salted peanuts, followed by ready-salted and salt and vinegar crisps, extruded maize, mixed-starch and prefabricated/fried potato products, and cheese-filled puffs. Other varieties of crisps (cheese and onion and special shapes) proved to be more cariogenic, not far short of semi-sweet biscuits in some cases. It is concluded that the severity of the processing undergone by the snack foods and the nature of the flavouring agents with which they are coated can influence their dental properties.

PLAN-TA9-2443(U), Rev. B Remediated Nitrate Salt (RNS) Surrogate Formulation and Testing Standard Procedure

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brown, Geoffrey Wayne

2016-03-16

This document identifies scope and some general procedural steps for performing Remediated Nitrate Salt (RNS) Surrogate Formulation and Testing. This Test Plan describes the requirements, responsibilities, and process for preparing and testing a range of chemical surrogates intended to mimic the energetic response of waste created during processing of legacy nitrate salts. The surrogates developed are expected to bound1 the thermal and mechanical sensitivity of such waste, allowing for the development of process parameters required to minimize the risk to worker and public when processing this waste. Such parameters will be based on the worst-case kinetic parameters as derived frommore » APTAC measurements as well as the development of controls to mitigate sensitivities that may exist due to friction, impact, and spark. This Test Plan will define the scope and technical approach for activities that implement Quality Assurance requirements relevant to formulation and testing.« less

Investigation of concentration-dependence of thermodynamic properties of lanthanum, yttrium, scandium and terbium in eutectic LiCl-KCl molten salt

NASA Astrophysics Data System (ADS)

Wang, Yafei; Zhou, Wentao; Zhang, Jinsuo

2016-09-01

Thermodynamic properties of rare earth metals in LiCl-KCl molten salt electrolyte are crucial to the development of electrochemical separation for the treatment of used nuclear fuels. In the present study, activity coefficient, apparent potential, and diffusion coefficient of lanthanum, yttrium, scandium, and terbium in the molten salt (58 at% LiCl and 42 at% KCl) were calculated by the method of molecular dynamics simulation up to a concentration around 3 at% at temperatures of 723 K and 773 K. It was found that the activity coefficient and the apparent potential increase with the species concentration while diffusion coefficient shows a trend of increase followed by decrease. The calculated results were validated by available measurement data of dilution cases. This research extends the range of data to a wide component and would provide further insight to the pyroprocessing design and safeguards.

Two Fixed Ratio Dilutions for Soil Salinity Monitoring in Hypersaline Wetlands

PubMed Central

Herrero, Juan; Weindorf, David C.; Castañeda, Carmen

2015-01-01

Highly soluble salts are undesirable in agriculture because they reduce yields or the quality of most cash crops and can leak to surface or sub-surface waters. In some cases salinity can be associated with unique history, rarity, or special habitats protected by environmental laws. Yet in considering the measurement of soil salinity for long-term monitoring purposes, adequate methods are required. Both saturated paste extracts, intended for agriculture, and direct surface and/or porewater salinity measurement, used in inundated wetlands, are unsuited for hypersaline wetlands that often are only occasionally inundated. For these cases, we propose the use of 1:5 soil/water (weight/weight) extracts as the standard for expressing the electrical conductivity (EC) of such soils and for further salt determinations. We also propose checking for ion-pairing with a 1:10 or more diluted extract in hypersaline soils. As an illustration, we apply the two-dilutions approach to a set of 359 soil samples from saline wetlands ranging in ECe from 2.3 dS m-1 to 183.0 dS m-1. This easy procedure will be useful in survey campaigns and in the monitoring of soil salt content. PMID:26001130

Two fixed ratio dilutions for soil salinity monitoring in hypersaline wetlands.

PubMed

Herrero, Juan; Weindorf, David C; Castañeda, Carmen

2015-01-01

Highly soluble salts are undesirable in agriculture because they reduce yields or the quality of most cash crops and can leak to surface or sub-surface waters. In some cases salinity can be associated with unique history, rarity, or special habitats protected by environmental laws. Yet in considering the measurement of soil salinity for long-term monitoring purposes, adequate methods are required. Both saturated paste extracts, intended for agriculture, and direct surface and/or porewater salinity measurement, used in inundated wetlands, are unsuited for hypersaline wetlands that often are only occasionally inundated. For these cases, we propose the use of 1:5 soil/water (weight/weight) extracts as the standard for expressing the electrical conductivity (EC) of such soils and for further salt determinations. We also propose checking for ion-pairing with a 1:10 or more diluted extract in hypersaline soils. As an illustration, we apply the two-dilutions approach to a set of 359 soil samples from saline wetlands ranging in ECe from 2.3 dS m(-1) to 183.0 dS m(-1). This easy procedure will be useful in survey campaigns and in the monitoring of soil salt content.

Ion Speciation and Transport Properties of LiTFSI in 1,3-Dioxolane Solutions: A Case Study for Li-S Battery Applications.

PubMed

Raccichini, Rinaldo; Dibden, James W; Brew, Ashley; Owen, John R; García-Aráez, Nuria

2018-01-11

Lithium-sulfur battery is considered to be one of the main candidates for "post-lithium-ion" battery generation because of its high theoretical specific capacity and inherently low cost. The role of electrolyte is particularly important in this system, and remarkable battery performances have been reported by tuning the amount of salt in the electrolyte. To further understand the reasons for such improvements, we chose the lithium bis(trifluoromethanesulfonyl)imide in 1,3-dioxolane electrolyte as a model salt-solvent system for a systematic study of conductivity and viscosity over a wide range of concentration from 10 -5 up to 5 m. The experimental results, discussed and interpreted with reference to the theory of electrolyte conductance, lead to the conclusion that triple ion formation is responsible for the highest molal conductivity values before reaching the maximum at 1.25 m. At higher concentrations, the molal conductivity drops quickly because of a rapid increase in viscosity and the salt-solvent system can be treated as a diluted form of molten salt.

Mesostructured Block Copolymer Nanoparticles: Versatile Templates for Hybrid Inorganic/Organic Nanostructures

PubMed Central

Connal, Luke A.; Lynd, Nathaniel A.; Robb, Maxwell J.; See, Kimberly A.; Jang, Se Gyu; Spruell, Jason M.

2012-01-01

We present a versatile strategy to prepare a range of nanostructured poly(styrene)-block-poly(2-vinyl pyridine) copolymer particles with tunable interior morphology and controlled size by a simple solvent exchange procedure. A key feature of this strategy is the use of functional block copolymers incorporating reactive pyridyl moieties which allow the absorption of metal salts and other inorganic precursors to be directed. Upon reduction of the metal salts, well-defined hybrid metal nanoparticle arrays could be prepared, while the use of oxide precursors followed by calcination permits the synthesis of silica and titania particles. In both cases, ordered morphologies templated by the original block copolymer domains were obtained. PMID:23335837

Considerations of the Differences between Bedded and Domal Salt Pertaining to Disposal of Heat-Generating Nuclear Waste

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hansen, Francis D.; Kuhlman, Kristopher L.; Sobolik, Steven R.

Salt formations hold promise for eternal removal of nuclear waste from our biosphere. Germany and the United States have ample salt formations for this purpose, ranging from flat-bedded formations to geologically mature dome structures. As both nations revisit nuclear waste disposal options, the choice between bedded, domal, or intermediate pillow formations is once again a contemporary issue. For decades, favorable attributes of salt as a disposal medium have been extoled and evaluated, carefully and thoroughly. Yet, a sense of discovery continues as science and engineering interrogate naturally heterogeneous systems. Salt formations are impermeable to fluids. Excavation-induced fractures heal as sealmore » systems are placed or natural closure progresses toward equilibrium. Engineering required for nuclear waste disposal gains from mining and storage industries, as humans have been mining salt for millennia. This great intellectual warehouse has been honed and distilled, but not perfected, for all nuances of nuclear waste disposal. Nonetheless, nations are able and have already produced suitable license applications for radioactive waste disposal in salt. A remaining conundrum is site location. Salt formations provide isolation and geotechnical barriers reestablish impermeability after waste is placed in the geology. Between excavation and closure, physical, mechanical, thermal, chemical, and hydrological processes ensue. Positive attributes for isolation in salt have many commonalities independent of the geologic setting. In some cases, specific details of the environment will affect the disposal concept and thereby define interaction of features, events and processes, while simultaneously influencing scenario development. Here we identify and discuss high-level differences and similarities of bedded and domal salt formations. Positive geologic and engineering attributes for disposal purposes are more common among salt formations than are significant differences. Developing models, testing material, characterizing processes, and analyzing performance all have overlapping application regardless of the salt formation of interest.« less

Considerations of the Differences between Bedded and Domal Salt Pertaining to Disposal of Heat-Generating Nuclear Waste

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hansen, Francis D.; Kuhlman, Kristopher L.; Sobolik, Steven R.

Salt formations hold promise for eternal removal of nuclear waste from our biosphere. Germany and the United States have ample salt formations for this purpose, ranging from flat-bedded formations to geologically mature dome structures. As both nations revisit nuclear waste disposal options, the choice between bedded, domal, or intermediate pillow formations is once again a contemporary issue. For decades, favorable attributes of salt as a disposal medium have been extoled and evaluated, carefully and thoroughly. Yet, a sense of discovery continues as science and engineering interrogate naturally heterogeneous systems. Salt formations are impermeable to fluids. Excavation-induced fractures heal as sealmore » systems are placed or natural closure progresses toward equilibrium. Engineering required for nuclear waste disposal gains from mining and storage industries, as humans have been mining salt for millennia. This great intellectual warehouse has been honed and distilled, but not perfected, for all nuances of nuclear waste disposal. Nonetheless, nations are able and have already produced suitable license applications for radioactive waste disposal in salt. A remaining conundrum is site location. Salt formations provide isolation, and geotechnical barriers reestablish impermeability after waste is placed in the geology. Between excavation and closure, physical, mechanical, thermal, chemical, and hydrological processes ensue. Positive attributes for isolation in salt have many commonalities independent of the geologic setting. In some cases, specific details of the environment will affect the disposal concept and thereby define interaction of features, events and processes, while simultaneously influencing scenario development. Here we identify and discuss high-level differences and similarities of bedded and domal salt formations. Positive geologic and engineering attributes for disposal purposes are more common among salt formations than are significant differences. Developing models, testing material, characterizing processes, and analyzing performance all have overlapping application regardless of the salt formation of interest.« less

Chain stiffness, salt valency, and concentration influences on titration curves of polyelectrolytes: Monte Carlo simulations

NASA Astrophysics Data System (ADS)

Carnal, Fabrice; Stoll, Serge

2011-01-01

Monte Carlo simulations have been used to study two different models of a weak linear polyelectrolyte surrounded by explicit counterions and salt particles: (i) a rigid rod and (ii) a flexible chain. We focused on the influence of the pH, chain stiffness, salt concentration, and valency on the polyelectrolyte titration process and conformational properties. It is shown that chain acid-base properties and conformational properties are strongly modified when multivalent salt concentration variation ranges below the charge equivalence. Increasing chain stiffness allows to minimize intramolecular electrostatic monomer interactions hence improving the deprotonation process. The presence of di and trivalent salt cations clearly promotes the chain degree of ionization but has only a limited effect at very low salt concentration ranges. Moreover, folded structures of fully charged chains are only observed when multivalent salt at a concentration equal or above charge equivalence is considered. Long-range electrostatic potential is found to influence the distribution of charges along and around the polyelectrolyte backbones hence resulting in a higher degree of ionization and a lower attraction of counterions and salt particles at the chain extremities.

Chain stiffness, salt valency, and concentration influences on titration curves of polyelectrolytes: Monte Carlo simulations.

PubMed

Carnal, Fabrice; Stoll, Serge

2011-01-28

Monte Carlo simulations have been used to study two different models of a weak linear polyelectrolyte surrounded by explicit counterions and salt particles: (i) a rigid rod and (ii) a flexible chain. We focused on the influence of the pH, chain stiffness, salt concentration, and valency on the polyelectrolyte titration process and conformational properties. It is shown that chain acid-base properties and conformational properties are strongly modified when multivalent salt concentration variation ranges below the charge equivalence. Increasing chain stiffness allows to minimize intramolecular electrostatic monomer interactions hence improving the deprotonation process. The presence of di and trivalent salt cations clearly promotes the chain degree of ionization but has only a limited effect at very low salt concentration ranges. Moreover, folded structures of fully charged chains are only observed when multivalent salt at a concentration equal or above charge equivalence is considered. Long-range electrostatic potential is found to influence the distribution of charges along and around the polyelectrolyte backbones hence resulting in a higher degree of ionization and a lower attraction of counterions and salt particles at the chain extremities.

Sodium intake, salt taste and gastric cancer risk according to Helicobacter pylori infection, smoking, histological type and tumor site in China.

PubMed

Zhong, Chen; Li, Kai-Nan; Bi, Jing-Wang; Wang, Bao-Cheng

2012-01-01

The risk factors mostly strongly associated with gastric cancer are gastric bacteria Helicobacter pylori and diet. Using a case-control study among residents in Jinan, we examined the association between the salt taste and gastric cancer according to H. pylori infection, smoking and histological type as well as tumor site. This population-based case-control study included 207 cases and 410 controls. Data on potential risk factors of gastric cancer were obtained by interview of cases and controls with a questionnaire, salt taste preference was measured for all subjects, and IgG antibodies to H. pylori were applied to assess infection. Risk measures were determined using unconditional logistic regression. The proportions of salt taste at intervals of 1.8-7.2 g/L and ≥ 7.2 g/L were significantly higher in cases than controls, with ORs of 1.56 (1.23-3.64) and 2.03 (2.12- 4.11), respectively, subjects with high salt intake having an elevated risk for gastric cancer when infected with H. pylori. Significant modification by smoking and tumor site was observed across the different measures of salt intake, the highest salt taste showed higher cancer risk in ever smokers or with non-cardia cancers. Our study supports the view that high intake of sodium is an important dietary risk factor for gastric cancer, with a synergistic effect found between salt and H.pylori and smoking, dependent on the tumor site.

Microspatial ecotone dynamics at a shifting range limit: plant–soil variation across salt marsh–mangrove interfaces

USGS Publications Warehouse

Yando, Erik S.; Osland, Michael J.; Hester, Mark H.

2018-01-01

Ecotone dynamics and shifting range limits can be used to advance our understanding of the ecological implications of future range expansions in response to climate change. In the northern Gulf of Mexico, the salt marsh–mangrove ecotone is an area where range limits and ecotone dynamics can be studied in tandem as recent decreases in winter temperature extremes have allowed for mangrove expansion at the expense of salt marsh. In this study, we assessed aboveground and belowground plant–soil dynamics across the salt marsh–mangrove ecotone quantifying micro-spatial patterns in horizontal extent. Specifically, we studied vegetation and rooting dynamics of large and small trees, the impact of salt marshes (e.g. species and structure) on mangroves, and the influence of vegetation on soil properties along transects from underneath the mangrove canopy into the surrounding salt marsh. Vegetation and rooting dynamics differed in horizontal reach, and there was a positive relationship between mangrove tree height and rooting extent. We found that the horizontal expansion of mangrove roots into salt marsh extended up to eight meters beyond the aboveground boundary. Variation in vegetation structure and local hydrology appear to control mangrove seedling dynamics. Finally, soil carbon density and organic matter did not differ within locations across the salt marsh-mangrove interface. By studying aboveground and belowground variation across the ecotone, we can better predict the ecological effects of continued range expansion in response to climate change.

Microspatial ecotone dynamics at a shifting range limit: plant-soil variation across salt marsh-mangrove interfaces.

PubMed

Yando, E S; Osland, M J; Hester, M W

2018-05-01

Ecotone dynamics and shifting range limits can be used to advance our understanding of the ecological implications of future range expansions in response to climate change. In the northern Gulf of Mexico, the salt marsh-mangrove ecotone is an area where range limits and ecotone dynamics can be studied in tandem as recent decreases in winter temperature extremes have allowed for mangrove expansion at the expense of salt marsh. In this study, we assessed aboveground and belowground plant-soil dynamics across the salt marsh-mangrove ecotone quantifying micro-spatial patterns in horizontal extent. Specifically, we studied vegetation and rooting dynamics of large and small trees, the impact of salt marshes (e.g. species and structure) on mangroves, and the influence of vegetation on soil properties along transects from underneath the mangrove canopy into the surrounding salt marsh. Vegetation and rooting dynamics differed in horizontal reach, and there was a positive relationship between mangrove tree height and rooting extent. We found that the horizontal expansion of mangrove roots into salt marsh extended up to eight meters beyond the aboveground boundary. Variation in vegetation structure and local hydrology appear to control mangrove seedling dynamics. Finally, soil carbon density and organic matter did not differ within locations across the salt marsh-mangrove interface. By studying aboveground and belowground variation across the ecotone, we can better predict the ecological effects of continued range expansion in response to climate change.

Effective Electrostatic Interactions Between Two Overall Neutral Surfaces with Quenched Charge Heterogeneity Over Atomic Length Scale

NASA Astrophysics Data System (ADS)

Zhou, S.

2017-12-01

Using Monte Carlo results as a reference, a classical density functional theory ( CDFT) is shown to reliably predict the forces between two heterogeneously charged surfaces immersed in an electrolyte solution, whereas the Poisson-Boltzmann ( PB) theory is demonstrated to deteriorate obviously for the same system even if the system parameters considered fall within the validity range of the PB theory in the homogeneously charged surfaces. By applying the tested CDFT, we study the effective electrostatic potential of mean force ( EPMF) between two face-face planar and hard surfaces of zero net charge on which positive and negative charges are separated and considered to present as discontinuous spots on the inside edges of the two surfaces. Main conclusions are summarized as follows: (i) strength of the EPMF in the surface charge separation case is very sensitively and positively correlated with the surface charge separation level and valency of the salt ion. Particularly, the charge separation level and the salt ion valency have a synergistic effect, which makes high limit of the EPMF strength in the surface charge separation case significantly go beyond that of the ideal homogeneously charged surface counterpart at average surface charge density similar to the average surface positive or negative charge density in the charge separation case. (ii) The surface charge distribution patterns mainly influence sign of the EPMF: symmetrical and asymmetrical patterns induce repulsive and attractive (at small distances) EPMF, respectively; but with low valency salt ions and low charge separation level the opposite may be the case. With simultaneous presence of both higher valency cation and anion, the EPMF can be repulsive at intermediate distances for asymmetrical patterns. (iii) Salt ion size has a significant impact, which makes the EPMF tend to become more and more repulsive with the ion diameter regardless of the surface charge distribution patterns and the valency of the salt ion; whereas if the 1:1 type electrolyte and the symmetrical patterns are considered, then the opposite may be the case. All of these findings can be explained self-consistently from several perspectives: an excess adsorption of the salt ions (induced by the surface charge separation) serving to raise the osmotic pressure between the plates, configuration fine-tuning in the thinner ion adsorption layer driven by the energy decrease principle, direct Coulombic interactions operating between charged objects on the two face-to-face plates involved, and net charge strength in the ion adsorption layer responsible for the net electrostatic repulsion.

Characterizing the fabric of the urban environment: A case study of Salt Lake City, Utah

DOE Office of Scientific and Technical Information (OSTI.GOV)

Akbari, Hashem; Rose, L. Shea

2001-02-28

Urban fabric data are needed in order to estimate the impact of light-colored surfaces (roofs and pavements) and urban vegetation (trees, grass, shrubs) on the meteorology and air quality of a city, and to design effective implementation programs. In this report, we discuss the result of a semi-automatic Monte-Carlo statistical approach used to develop data on surface-type distribution and city-fabric makeup (percentage of various surface-types) using aerial color orthophotography. The digital aerial photographs for Salt Lake City covered a total of about 34 km2 (13 mi2). At 0.50-m resolution, there were approximately 1.4 x 108 pixels of data. Four majormore » land-use types were examined: (1) commercial, (2) industrial, (3) educational, and (4) residential. On average, for the areas studied, vegetation covers about 46 percent of the area (ranging 44-51 percent), roofs cover about 21 percent (ranging 15-24 percent), and paved surfaces about 26 percent (ranging 21-28 percent). For the most part, trees shade streets, parking lots, grass, and sidewalks. In most non-residential areas, paved surfaces cover 46-66 percent of the area. In residential areas, on average, paved surfaces cover about 32 percent of the area. Land-use/land-cover (LU/LC) data from the United States Geological Survey were used to extrapolate these results from neighborhood scales to metropolitan Salt Lake City. In an area of roughly 560 km2, defining most of metropolitan Salt Lake City, over 60 percent is residential. The total roof area is about 110 km2, and the total paved surface area (roads, parking areas, sidewalks) covers about 170 km2. The total vegetated area covers about 230 km2.« less

Log analysis of six boreholes in conjunction with geologic characterization above and on top of the Weeks Island salt dome

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sattler, A.R.

1996-04-01

Six boreholes were drilled during the geologic characterization and diagnostics of the Weeks Island sinkhole that is over the two-tiered salt mine which was converted for oil storage by the US Strategic Petroleum Reserve. These holes were drilled to provide for geologic characterization of the Weeks Island Salt Dome and its overburden in the immediate vicinity of the sinkhole (mainly through logs and core); to establish a crosswell configuration for seismic tomography; to establish locations for hydrocarbon detection and tracer injection; and to Provide direct observations of sinkhole geometry and material properties. Specific objectives of the logging program were to:more » (1) identify the top of and the physical state of the salt dome; (2) identify the water table; (3) obtain a relative salinity profile in the aquifer within the alluvium, which ranges from the water table directly to the top of the Weeks Island salt dome; and (4) identify a reflecting horizon seen on seismic profiles over this salt dome. Natural gamma, neutron, density, sonic, resistivity and caliper logs were run. Neutron and density logs were run from inside the well casing because of the extremely unstable condition of the deltaic alluvium overburden above the salt dome. The logging program provided important information about the salt dome and the overburden in that (1) the top of the salt dome was identified at {approximately}189 ft bgl (103 ft msl), and the top of the dome contains relatively few fractures; (2) the water table is approximately 1 ft msl, (3) this aquifer appears to become steadily more saline with depth; and (4) the water saturation of much of the alluvium over the salt dome is shown to be influenced by the prevalent heavy rainfall. This logging program, a part of the sinkhole diagnostics, provides unique information about this salt dome and the overburden.« less

DC electrophoresis and viscosity of realistic salt-free concentrated suspensions: non-equilibrium dissociation-association processes.

PubMed

Ruiz-Reina, Emilio; Carrique, Félix; Lechuga, Luis

2014-03-01

Most of the suspensions usually found in industrial applications are concentrated, aqueous and in contact with the atmospheric CO2. The case of suspensions with a high concentration of added salt is relatively well understood and has been considered in many studies. In this work we are concerned with the case of concentrated suspensions that have no ions different than: (1) those stemming from the charged colloidal particles (the added counterions, that counterbalance their surface charge); (2) the H(+) and OH(-) ions from water dissociation, and (3) the ions generated by the atmospheric CO2 contamination. We call this kind of systems "realistic salt-free suspensions". We show some theoretical results about the electrophoretic mobility of a colloidal particle and the electroviscous effect of realistic salt-free concentrated suspensions. The theoretical framework is based on a cell model that accounts for particle-particle interactions in concentrated suspensions, which has been successfully applied to many different phenomena in concentrated suspensions. On the other hand, the water dissociation and CO2 contamination can be described following two different levels of approximation: (a) by local equilibrium mass-action equations, because it is supposed that the reactions are so fast that chemical equilibrium is attained everywhere in the suspension, or (b) by non-equilibrium dissociation-association kinetic equations, because it is considered that some reactions are not rapid enough to ensure local chemical equilibrium. Both approaches give rise to different results in the range from dilute to semidilute suspensions, causing possible discrepancies when comparing standard theories and experiments concerning transport properties of realistic salt-free suspensions. Copyright © 2013 Elsevier Inc. All rights reserved.

[Gold salt alveolitis in 3 patients with rheumatoid arthritis].

PubMed

Music, E; Tomsic, M; Logar, D

1995-06-01

When the characteristic symptoms for an interstitial pulmonary disease arise in patients with rheumatoid arthritis, a drug-induced alveolitis should be considered in the differential diagnosis. In such cases, the administration of the drug and gold salts should be stopped. The cases of three patients with rheumatoid arthritis (RA) who had been treated with gold salts for 2 months (A), 23 months (B), and 36 months (C) are presented. The total dose of sodium aureothiomalate amounted to 280 mg for patient A, 1150 mg for patient B, and 2190 mg for patient C. Clinical signs, X-rays of the lungs, pulmonary function tests, and laboratory tests were evaluated for the three patients while, for patient A BAL as well as provocation tests were additionally performed before and after therapy. In this case, the histological picture of the lungs is presented; biopsies were taken during the first BAL. The clinical complaints of all 3 patients were similar, with the alveolitis being observed as diffuse in one case and above all in the upper regions in two cases on radiology. This led to differing degrees of diffusion disorders in the lungs. In patient A, the diagnosis was made in the stage of progressive fibrotic alveolitis and was treated with D-penicillamine. All 3 patients received steroids over 3-6 months and the gold salts were stopped. Because of the long duration and doubtful differential diagnosis for patient A with either rheumatoid lung or gold salt alveolitis, a provocation test with sodium aureothiomalate was performed. All 3 patients had blood eosinophilia while, in case A, a thrombopenia was also found. A gold salt alveolitis can occur as a side effect of gold salts in addition to skin vasculitis and hematological disorders. When the gold salt administration is not stopped a fibrotic alveolitis can develop. The provocation test can be diagnostically useful to distinguish between a rheumatoid lung and gold salt alveolitis.

Iodine Intake through Processed Food: Case Studies from Egypt, Indonesia, the Philippines, the Russian Federation and Ukraine, 2010–2015

PubMed Central

Knowles, Jacky; Shehata, Magdy; Gerasimov, Gregory; Bimo, Bimo; Cavenagh, Bettina; Maramag, Cherry C.; Otico, Edward; Izwardy, Doddy; Spohrer, Rebecca; Garrett, Greg S.

2017-01-01

The current performance indicator for universal salt iodisation (USI) is the percentage of households using adequately iodised salt. However, the proportion of dietary salt from household salt is decreasing with the increase in consumption of processed foods and condiments globally. This paper reports on case studies supported by the Global Alliance for Improved Nutrition (GAIN)-UNICEF USI Partnership Project to investigate processed food industry use of adequately iodised salt in contrasting national contexts. Studies were conducted in Egypt, Indonesia, the Philippines, the Russian Federation, and Ukraine. In all cases, the potential iodine intake from iodised salt in selected food products was modelled according to the formula: quantity of salt per unit of food product × minimum regulated iodine level of salt at production × average daily per capita consumption of the product. The percent of adult recommended nutrient intake for iodine potentially provided by the average daily intake of bread and frequently consumed foods and condiments was from 10% to 80% at the individual product level. The potential contribution to iodine intake from the use of iodised salt in the processed food industry is of growing significance. National USI strategies should encourage co-operative industry engagement and include regulatory monitoring of iodised salt use in the food industry in order to achieve optimal population iodine status. PMID:28933750

FY16 Summary Report: Participation in the KOSINA Project

DOE Office of Scientific and Technical Information (OSTI.GOV)

Matteo, Edward N.; Hansen, Francis D.

Salt formations represent a promising host for disposal of nuclear waste in the United States and Germany. Together, these countries provided fully developed safety cases for bedded salt and domal salt, respectively. Today, Germany and the United States find themselves in similar positions with respect to salt formations serving as repositories for heat-generating nuclear waste. German research centers are evaluating bedded and pillow salt formations to contrast with their previous safety case made for the Gorleben dome. Sandia National Laboratories is collaborating on this effort as an Associate Partner, and this report summarizes that teamwork. Sandia and German research groupsmore » have a long-standing cooperative approach to repository science, engineering, operations, safety assessment, testing, modeling and other elements comprising the basis for salt disposal. Germany and the United States hold annual bilateral workshops, which cover a spectrum of issues surrounding the viability of salt formations. Notably, recent efforts include development of a database for features, events, and processes applying broadly and generically to bedded and domal salt. Another international teaming activity evaluates salt constitutive models, including hundreds of new experiments conducted on bedded salt from the Waste Isolation Pilot Plant. These extensive collaborations continue to build the scientific basis for salt disposal. Repository deliberations in the United States are revisiting bedded and domal salt for housing a nuclear waste repository. By agreeing to collaborate with German peers, our nation stands to benefit by assurance of scientific position, exchange of operational concepts, and approach to elements of the safety case, all reflecting cost and time efficiency.« less

Geology and ground-water features of salt springs, seeps, and plains in the Arkansas and Red River basins of western Oklahoma and adjacent parts of Kansas and Texas

USGS Publications Warehouse

Ward, P.E.

1963-01-01

The salt springs, seeps, and plains described in this report are in the Arkansas and Red River basins in western Oklahoma and adjacent areas in Kansas and Texas. The springs and seeps contribute significantly to the generally poor water quality of the rivers by bringing salt (HaCI) to the surface at an estimated daily rate of more than 8,000 tons. The region investigated is characterized by low hills and rolling plains. Many of the rivers are eroded 100 feet or more below the .surrounding upland surface and in places the valleys are bordered by steep bluffs. The alluvial plains of the major rivers are wide and the river channels are shallow and unstable. The flow of many surface streams is intermittent, especially in the western part of the area. All the natural salt-contributing areas studied are within the outcrop area of rocks of Permian age. The Permian rocks, commonly termed red beds, are composed principally of red and gray gypsiferous shale, siltstone, sandstone, gypsum, anhydrite, and dolomite. Many of the formations contain halite in the subsurface. The halite occurs mostly as discontinuous lenses in shale, although some of the thicker, more massive beds are extensive. It underlies the entire region studied at depths ranging from about 30 feet to more than 2,000 feet. The salt and associated strata show evidence of extensive removal of salt through solution by ground water. Although the salt generally occurs in relatively impervious shale small joints and fractures ,allow the passage of small quantities of water which dissolves the salt. Salt water occurs in the report area at depths ranging from less than 100 feet to more than 1,000 feet. Salt water occurs both as meteoric and connate, but the water emerging as salt springs is meteoric. Tritium analyses show that the age of the water from several springs is less than 20 years. The salt springs, seeps, and plains are confined to 13 local areas. The flow of the springs and seeps is small, but the chloride concentration in the water ranges from a few hundred parts per million to about 190,000 ppm. The wide range of concentration is believed to be due, in part, to differential dilution by fresh water. Alluvium in the vicinity of the salt springs remains saturated with salt water and evaporation from the alluvial surface causes the formation of a salt crust during dry weather. Those areas appear as salt plains that range in size from less than an acre to as much as 60 square miles. The rocks exposed at the surface in the vicinity of the salt springs are permeable enough to allow the infiltration of some precipitation. Under certain geologic and hydrologic conditions ground water percolates down and through salt-bearing rocks where it dissolves the .salt. Hydrostatic pressure of ground water at higher elevations forces the salt water to emerge as salt springs at lower elevations.

Comprehensive analysis of "bath salts" purchased from California stores and the internet.

PubMed

Schneir, A; Ly, B T; Casagrande, K; Darracq, M; Offerman, S R; Thornton, S; Smollin, C; Vohra, R; Rangun, C; Tomaszewski, C; Gerona, R R

2014-08-01

To analyze the contents of "bath salt" products purchased from California stores and the Internet qualitatively and quantitatively in a comprehensive manner. A convenience sample of "bath salt" products were purchased in person by multiple authors at retail stores in six California cities and over the Internet (U.S. sites only), between August 11, 2011 and December 15, 2011. Liquid chromatography-time-of-flight mass spectrometry was utilized to identify and quantify all substances in the purchased products. Thirty-five "bath salt" products were purchased and analyzed. Prices ranged from $9.95 to 49.99 (U.S. dollars). Most products had a warning against use. The majority (32/35, 91%) had one (n = 15) or multiple cathinones (n = 17) present. Fourteen different cathinones were identified, 3,4-methylenedioxypyrovalerone (MDPV) being the most common. Multiple drugs found including cathinones (buphedrone, ethcathinone, ethylone, MDPBP, and PBP), other designer amines (ethylamphetamine, fluoramphetamine, and 5-IAI), and the antihistamine doxylamine had not been previously identified in U.S. "bath salt" products. Quantification revealed high stimulant content and in some cases dramatic differences in either total cathinone or synthetic stimulant content between products with the same declared weight and even between identically named and outwardly appearing products. Comprehensive analysis of "bath salts" purchased from California stores and the Internet revealed the products to consistently contain cathinones, alone, or in different combinations, sometimes in high quantity. Multiple cathinones and other drugs found had not been previously identified in U.S. "bath salt" products. High total stimulant content in some products and variable qualitative and quantitative composition amongst products were demonstrated.

High-temperature electrolysis of synthetic seawater using solid oxide electrolyzer cells

NASA Astrophysics Data System (ADS)

Lim, Chee Kuan; Liu, Qinglin; Zhou, Juan; Sun, Qiang; Chan, Siew Hwa

2017-02-01

A Ni-YSZ/YSZ/LSCF-GDC solid oxide electrolyzer cell (SOEC) is used to investigate the effects of seawater electrolysis for hydrogen production through electrolyzing steam produced from simulated seawater bath. Steam electrolysis using an SOEC with its fuel electrode contaminated by sea salt is also investigated. Steam produced from seawater is found to be free of contaminants, which are present in the seawater. Similar electrochemical performance is observed from the polarization curves and impedance spectra when using steam produced from pure water and seawater. Their short-term degradation rates are similar, which are registered at 15% 1000 h-1 for both cases. For the case of direct sea salt contamination in an SOEC's fuel electrode, both the uncontaminated and contaminated cells exhibit rather similar performance as observed from the polarization curves and impedance spectra. The difference in ASR values from the polarization curves and impedance spectra between the uncontaminated and contaminated cell are all within a 10% range. Rather similar short-term degradation rates of 15% 1000 h-1 and 16% 1000 h-1 are recorded for the uncontaminated and contaminated cells, respectively. Post-mortem analysis shows that the sea salt impregnated into the cell has been vaporized at a typical SOEC operating temperature of 800 °C over the period of operation.

Metabolic Capabilities of the Members of the Order Halanaerobiales and Their Potential Biotechnological Applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Roush, Daniel W; Elias, Dwayne A; Mormile, Dr. Melanie R.

The order Halanaerobiales contains a number of well-studied halophiles that possess great potential for biotechnological applications. The unique halophilic adaptations that these organisms utilize, such as salting-in mechanisms to increase their intercellular concentration of KCl, combined with their ability to ferment simple sugars, provides an excellent platform for biotechnological development over a wide range of salt levels and possible other extreme conditions, such as alkaline conditions. From fermented foods to oil reservoirs, members of Halanaerobiales are found in many environments. The environmental conditions many of these organisms grow are similar to industrially important processes, such as alkaline pre-treated biomass stocks,more » treatment of crude glycerol from biodiesel production, salty fermented foods, as well as bioremediation of contaminants under extreme conditions of salinity and in some cases, alkalinity. From salt stable enzymes to waste fermentations, bioremediation options, bioenergy, and microbially enhanced oil recovery (MEOR), Halanaerobiales can provide a wide spectrum of environmentally friendly solutions to current problems.« less

Behaviour of I/Br/Cl-THMs and their projected toxicities under simulated cooking conditions: Effects of heating, table salt and residual chlorine.

PubMed

Yan, Mingquan; Li, Mingyang; Han, Xuze

2016-08-15

This study examined the effects of heating, residual chlorine and concentration of table salt on the generation of iodine-, bromine- and chlorine-containing trihalomethanes (THMs) under simulated cooking conditions. In the case of addition of either KI- or KIO3-fortified salt, total I-THM concentrations increased with increasing iodine concentration, while total Cl/Br-THM concentrations decreased. CHCl2I, CHBrClI, CHBrI2, CHBr2I and CHI3 were formed in the presence of KI salt, while only CHCl2I was formed in the presence of KIO3 salt. CHCl2I was unstable under cooking conditions, and >90% of this DBP was removed during heating, which in some cases increased the concentrations of the other I-THMs. The calculated cytotoxicity increased with addition of KI- or KIO3-fortified salt due to the generation of I-THMs, whose impact on the cytotoxicity at room temperature was equal to or five times higher, respectively, than the cytotoxicity of the simultaneously formed Cl/Br-THMs for the cases of salts. Heating decreased the cytotoxicity, except for the case of addition of KI salt, in which the calculated cytotoxicity of I-THMs increased above 150% as the temperature was increased up to 100°C. The reported results may have important implications for epidemiologic exposure assessments and, ultimately, for public health protection. Copyright © 2016 Elsevier B.V. All rights reserved.

Structural instability and electronic localization in the 2:1 salts: The case of the Fabre and the (DMtTTF){2}CIO{4}salts

NASA Astrophysics Data System (ADS)

Ravy, S.; Foury-Leylekian, P.; Le Bolloc'h, D.; Pouget, J.-P.; Fabre, J. M.; Prado, R. J.; Lagarde, P.

2004-04-01

The charge ordering observed in the (TMTTF){2}X family has been studied by X-ray absorption spectroscopy. XANES measurements at the Sulfur K-edge show no evidence of charge disproportionation larger than 0.5 e, and EXAFS at the Phosphorus K-edge indicate no displacements of the PF{6} anion larger than 0.05 Å. The difficulty to observe a structural signature of this charge ordering is due to the triclinic symmetry of these salts. By contrast, in the monoclinic charge transfer salt (DMtTTF){2}ClO{4}, a screw axis symmetry constrains the molecular stacks to be uniform. In this real 1/4-filled system, charge localization is observed at about 150 K. We show that around this temperature an incommensurate modulation of reduced wave vector (0.58,0,-0.275) is stabilized. The transition is strongly hysteretic, but no long range order is established. We suggest that this modulation, which has the 4k{F} periodicity in the chain direction, stabilizes a local antiferroelectric state similar to the one previously observed in (TMTTF){2}SCN. Key words. Charge ordering, Structural phase transition.

Calix[4]pyrrole as a Chloride Anion Receptor: Solvent and Counter-Cation Effects

PubMed Central

Sessler, Jonathan L.; Gross, Dustin E.; Cho, Won-Seob; Lynch, Vincent M.; Schmidtchen, Franz P.; Bates, Gareth W.; Light, Mark E.; Gale, Philip A.

2008-01-01

The interaction of calixpyrrole with several chloride salts has been studied in the solid state by X-ray crystallography as well as in solution by isothermal titration calorimetry (ITC) and 1H NMR spectroscopic titrations. The titration results in dimethylsulfoxide, acetonitrile, nitromethane, 1,2-dichloroethane and dichloromethane, carried out using various chloride salts, specifically tetraethylammonium (TEA), tetrapropylammonium (TPA), tetrabutylammonium (TBA), tetraethylphosphonium (TEP), tetrabutylphosphonium (TBP), and tetraphenylphosphonium (TPhP) showed no dependence on method of measurement. The resulting affinity constants (Ka's), on the other hand, were found to be highly dependent on the choice of solvent with Ka's ranging from 102−105 being recorded in the test solvents used for this study. In dichloromethane a strong dependence on the counter-cation was also seen, with the Ka's for the interaction with chloride ranging from 102−104. In the case of TPA, TBA and TBP the ITC data could not be fit to a 1:1 binding profile. PMID:16967979

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bauer, Stephen J.; Urquhart, Alexander

Reconsolidated crushed salt is being considered as a backfilling material placed upon nuclear waste within a salt repository environment. In-depth knowledge of thermal and mechanical properties of the crushed salt as it reconsolidates is critical to thermal/mechanical modeling of the reconsolidation process. An experimental study was completed to quantitatively evaluate the thermal conductivity of reconsolidated crushed salt as a function of porosity and temperature. The crushed salt for this study came from the Waste Isolation Pilot Plant (WIPP). In this work the thermal conductivity of crushed salt with porosity ranging from 1% to 40% was determined from room temperature upmore » to 300°C, using two different experimental methods. Thermal properties (including thermal conductivity, thermal diffusivity and specific heat) of single-crystal salt were determined for the same temperature range. The salt was observed to dewater during heating; weight loss from the dewatering was quantified. The thermal conductivity of reconsolidated crushed salt decreases with increasing porosity; conversely, thermal conductivity increases as the salt consolidates. The thermal conductivity of reconsolidated crushed salt for a given porosity decreases with increasing temperature. A simple mixture theory model is presented to predict and compare to the data developed in this study.« less

Polymer Electrolyte Based on Poly(ethylene imine) and Lithium Salts.

DTIC Science & Technology

1985-10-01

plots of AC impedance data obtained over the frequency range from 100 Nz to 13 az12 . AC impedance was determined using a computerized Hewlett-Packard...E. Yasger repartment of Chemistry Dr. Sam Perone Case Western Reserve University Chemitry & Materials Cleveland, Ohio 41106 1 Scifnte Department...1 Dr. Carl Kannewurf borthvestern University Dr. Joseph Gordon, I1 Dipartment of Electrical Engineering IB Corporation and Computer Science X33/281

Diclofenac Salts. V. Examples of Polymorphism among Diclofenac Salts with Alkyl-hydroxy Amines Studied by DSC and HSM

PubMed Central

Fini, Adamo; Cavallari, Cristina; Ospitali, Francesca

2010-01-01

Nine diclofenac salts prepared with alkyl-hydroxy amines were analyzed for their properties to form polymorphs by DSC and HSM techniques. Thermograms of the forms prepared from water or acetone are different in most cases, suggesting frequent examples of polymorphism among these salts. Polymorph transition can be better highlighted when analysis is carried out by thermo-microscopy, which in most cases made it possible to observe the processes of melting of the metastable form and re-crystallization of the stable one. Solubility values were qualitatively related to the crystal structure of the salts and the molecular structure of the cation. PMID:27721347

Removal of foot-and-mouth disease virus infectivity in salted natural casings by minor adaptation of standardized industrial procedures.

PubMed

Wijnker, J J; Haas, B; Berends, B R

2007-04-10

Intestines are used for the production of natural casings as edible sausage containers. Derived from animals (pigs and sheep) experimentally infected with FMDV (initial dosage 10(7.3) PFU/ml, strain O(1Kaufbeuren)), these natural casings were treated with sodium chloride or a phosphate salts/sodium chloride mixture and the residual FMDV titres measured. After storage at about 20 degrees C, no remaining infectivity was found after either treatment, whereas casings stored at 4 degrees C still contained infectivity. Storage of salted casings at about 20 degrees C for 30 days is already part of the Standard Operating Procedures (included in HACCP) of the international casing industry and can therefore be considered as a protective measure for the international trade in natural casings.

Mangrove expansion and salt marsh decline at mangrove poleward limits.

PubMed

Saintilan, Neil; Wilson, Nicholas C; Rogers, Kerrylee; Rajkaran, Anusha; Krauss, Ken W

2014-01-01

Mangroves are species of halophytic intertidal trees and shrubs derived from tropical genera and are likely delimited in latitudinal range by varying sensitivity to cold. There is now sufficient evidence that mangrove species have proliferated at or near their poleward limits on at least five continents over the past half century, at the expense of salt marsh. Avicennia is the most cold-tolerant genus worldwide, and is the subject of most of the observed changes. Avicennia germinans has extended in range along the USA Atlantic coast and expanded into salt marsh as a consequence of lower frost frequency and intensity in the southern USA. The genus has also expanded into salt marsh at its southern limit in Peru, and on the Pacific coast of Mexico. Mangroves of several species have expanded in extent and replaced salt marsh where protected within mangrove reserves in Guangdong Province, China. In south-eastern Australia, the expansion of Avicennia marina into salt marshes is now well documented, and Rhizophora stylosa has extended its range southward, while showing strong population growth within estuaries along its southern limits in northern New South Wales. Avicennia marina has extended its range southwards in South Africa. The changes are consistent with the poleward extension of temperature thresholds coincident with sea-level rise, although the specific mechanism of range extension might be complicated by limitations on dispersal or other factors. The shift from salt marsh to mangrove dominance on subtropical and temperate shorelines has important implications for ecological structure, function, and global change adaptation. © 2013 John Wiley & Sons Ltd.

Linguistic and pragmatic constraints on utterance interpretation

NASA Astrophysics Data System (ADS)

Hinkelman, Elizabeth A.

1990-05-01

In order to model how people understand language, it is necessary to understand not only grammar and logic but also how people use language to affect their environment. This area of study is known as natural language pragmatics. Speech acts, for instance, are the offers, promises, announcements, etc., that people make by talking. The same expression may be different acts in different contexts, and yet not every expression performs every act. We want to understand how people are able to recognize other's intentions and implications in saying something. Previous plan-based theories of speech act interpretation do not account for the conventional aspect of speech acts. They can, however, be made sensitive to both linguistic and propositional information. This dissertation presents a method of speech act interpretation which uses patterns of linguistic features (e.g., mood, verb form, sentence adverbials, thematic roles) to identify a range of speech act interpretations for the utterance. These are then filtered and elaborated by inferences about agents' goals and plans. In many cases the plan reasoning consists of short, local inference chains (that are in fact conversational implicatures) and, extended reasoning is necessary only for the most difficult cases. The method is able to accommodate a wide range of cases, from those which seem very idiomatic to those which must be analyzed using knowledge about the world and human behavior. It explains how, Can you pass the salt, can be a request while, Are you able to pass the salt, is not.

Ultrasonic Technique for Predicting Grittiness of Salted Duck Egg

NASA Astrophysics Data System (ADS)

Erawan, S.; Budiastra, I. W.; Subrata, I. D. M.

2018-05-01

Grittiness of egg yolk is a major factor in consumer acceptance of salted duck egg product. Commonly, the grittiness level is determined by the destructive method. Salted egg industries need a grading system that can judge the grittiness accurately and nondestructively. The purpose of this study was to develop a method for determining grittiness of salted duck eggs nondestructively based on ultrasonic method. This study used 100 samples of salted duck eggs with 7,10,14 and 21 days of salting age. Velocity and attenuation were measured by an ultrasonic system at frequency 50 kHz, followed by physicochemical properties measurement (hardness of egg yolks and salt content), and organoleptic test. Ultrasonic wave velocity in salted duck eggs ranged from 620.6 m/s to 1334.6 m/s, while the coefficient of attenuation value ranged from – 0.76 dB/m to -0.51 dB/m. Yolk hardness was 2.68 N at 7 days to 5.54 N at 21 days of salting age. Salt content was 1.81 % at 7 days to 5.71 % at 21 days of salting age. Highest scores of organoleptic tests on salted duck eggs were 4.23 and 4.18 for 10 and 14 days of salting age, respectively. Discriminant function using ultrasonic velocity variables in minor and major diameter could predict grittiness with 95 % accuracy.

Performance of concrete pavement in the presence of deicing salts and deicing salt cocktails.

DOT National Transportation Integrated Search

2016-05-01

Deicing salts are widely used for anti-icing and de-icing operations in pavements. While historically sodium chloride may have been the : deicer most commonly used, a wide range of deicing salts have begun to be used to operate at lower temperatures,...

Mangrove expansion and saltmarsh decline at mangrove poleward limits

USGS Publications Warehouse

Saintilan, Neil; Wilson, Nicholas C.; Rogers, Kerrylee; Rajkaran, Anusha; Krauss, Ken W.

2014-01-01

Mangroves are species of halophytic intertidal trees and shrubs derived from tropical genera and are likely delimited in latitudinal range by varying sensitivity to cold. There is now sufficient evidence that mangrove species have proliferated at or near their poleward limits on at least five continents over the past half century, at the expense of salt marsh. Avicennia is the most cold-tolerant genus worldwide, and is the subject of most of the observed changes. Avicennia germinans has extended in range along the US Atlantic coast and expanded into salt marsh as a consequence of lower frost frequency and intensity in the southern USA. The genus has also expanded into salt marsh at its southern limit in Peru, and on the Pacific coast of Mexico. Mangroves of several species have expanded in extent and replaced salt marsh where protected within mangrove reserves in Guangdong Province. In south-eastern Australia, the expansion of Avicennia marina into salt marshes is now well documented, and Rhizophora stylosa has extended its range southward, while showing strong population growth within estuaries along its southern limits in northern New South Wales. Avicennia marina has extended its range southwards in South Africa. The changes are consistent with the pole-ward extension of temperature thresholds co-incident with sea-level rise, although the specific mechanism of range extension might be complicated by limitations on dispersal or other factors. The shift from salt marsh to mangrove dominance on subtropical and temperate shorelines has important implications for ecological structure, function, and global change adaptation.

Molten salt synthesis of La0.8Sr0.2MnO3 powders for SOFC cathode electrode

NASA Astrophysics Data System (ADS)

Gu, Sin-il; Shin, Hyo-soon; Hong, Youn-woo; Yeo, Dong-hun; Kim, Jong-hee; Nahm, Sahn; Yoon, Sang-ok

2012-08-01

For La0.8Sr0.2MnO3 (LSM) perovskite, used as the cathode material for solid oxide fuel cells (SOFC), it is known that the formation of a triple-phase-boundary is restrained due to the formation of a second phase at the YSZ/electrode interface at high temperature. To decrease the 2nd phase, lowering the sintering temperature has been used. LSM powder was synthesized by molten salt synthesis method to control its particle size, shape, and agglomeration. We have characterized the phase formation, particle size, shape, and sintering behavior of LSM in the synthesis using the variation of KCl, LiCl, KF and its mixed salts as raw materials. In the case of KCl and KCl-KF salts, the particle size and shape of the LSM was well controlled and synthesized. However, in the case of LiCl and KCl-LiCl salts, LiMnOx as 2nd phase and LSM were synthesized simultaneously. In the case of the mixed salt of KCl-KF, the growth mechanism of the LSM particle was changed from `diffusion-controlled' to `reaction-controlled' according to the amount of mixed salt. The sintering temperature can be decreased below 1000 °C by using the synthesized LSM powder.

Chemistry and Spectroscopy of Frozen Chloride Salts on Icy Bodies

NASA Astrophysics Data System (ADS)

Johnson, P. V.; Thomas, E. C.; Hodyss, R. P.; Vu, T. H.; Choukroun, M.

2016-12-01

Understanding the habitability of Europa's ocean is of great interest to astrobiology and is the focus of missions currently being considered to explore Europa. Currently, our best means of constraining the subsurface ocean composition and its subsequent habitability is by further study of Europa's surface chemical composition. Analysis of existing (and future) remote sensing data is limited by the availability of spectral libraries of candidate materials under relevant conditions (temperature, thermal/radiation history, etc.). Geochemical predictions of Europa's ocean composition suggest that chloride salts are likely to exist on the surface of Europa as well as other ocean worlds. We have conducted a study of frozen chloride-salt brines prepared at temperatures, pressures and radiation conditions (UV) in order to simulate conditions on the surface of Europa and other airless bodies. Hydration states of various chloride salts as a function of temperature were determined using Raman spectroscopy. Near IR reflectance spectra of identically prepared samples were measured to provide reference spectra of the identified hydrated salts. We find that the freezing of NaCl at temperatures ranging from 80 K to 233 K forms hydrohalite. In contrast, KCl hydrates are not formed from the freezing of KCl brines. In addition, a stable hexahydrate forms from the freezing of MgCl2 solutions, while a hexahydrate, a tetrahydrate, and a dihydrate, form upon freezing of CaCl2 solutions. Salts were observed to dehydrated with increasing temperatures, leading to a succession of hydration states in the case of CaCl2. Irradiation with vacuum ultraviolet light was observed to lead to dehydration as well.

Chemistry and Spectroscopy of Frozen Chloride Salts on Icy Bodies

NASA Astrophysics Data System (ADS)

Johnson, Paul; Thomas, Elena C.; Hodyss, Robert; Vu, Tuan; Choukroun, Mathieu

2016-10-01

Currently, our understanding of the chemical composition of Europa's surface is our best means of inferring constraints on the subsurface ocean composition and its subsequent habitability. The bulk of our knowledge of Europa surface chemistry can be traced to near infrared spectra recorded by the Near Infrared Mapping Spectrometer on the Galileo spacecraft. However, the usefulness of this and other remote sensing data is limited by the availability of spectral libraries of candidate materials under relevant conditions (temperature, thermal/radiation history, etc.). Chloride salts are expected to exist on the surface of Europa, and other icy bodies, based on geochemical predictions of the ocean composition. In order to help improve our understanding of Europa's surface composition, we have conducted a study of frozen chloride-salt brines prepared under simulated Europa surface conditions (vacuum, temperature, and UV irradiation) using both near IR and Raman spectroscopies. Specifically, Raman spectroscopy was used to determine the hydration states of various chloride salts as a function of temperature. Near IR spectroscopy of identically prepared samples was used to provide reference reflectance spectra of the identified hydrated salts. Our results indicate that at temperatures ranging from 80 K to 233 K, hydrohalite is formed from the freezing of NaCl brines, while the freezing of KCl solutions does not form KCl hydrates. In addition, the freezing of MgCl2 solutions forms a stable hexahydrate, and the freezing of CaCl2 solutions forms a hexahydrate, a tetrahydrate, and a dihydrate. Dehydration of the salts was observed as temperatures were increased, leading to a succession of hydration states in the case of CaCl2.

Food-grade submicrometer particles from salts prepared using ethanol-in-oil mixtures.

PubMed

Paques, Jerome P; van der Linden, Erik; Sagis, Leonard M C; van Rijn, Cees J M

2012-08-29

A simple method for preparing food-grade particles in the submicrometer range of ethanol soluble salts using ethanol-in-oil (E/O) mixtures is described. Salts CaCl2·2H2O and MgCl2·6H2O were dissolved in ethanol that subsequently was mixed with a medium-chain triglyceride oil phase. It was found that type and concentration of salt have a significant influence on the miscibility of ethanol and oil phase and on the stability of E/O mixtures. The ethanol phase was evaporated from the mixture at elevated temperatures, and salt particles with dimensions in the submicrometer range (6-400 nm) remained suspended in the oil phase. It was found that the concentration of salt and volume fraction of ethanol in MCT oil have a significant influence on the size distribution of salt particles. The size of CaCl2 and MgCl2 submicrometer particles was ascertained by scanning electron microscopy and dynamic light scattering.

Inactivation of foot-and-mouth disease virus in various bovine tissues used for the production of natural sausage casings.

PubMed

Wijnker, Joris J; Haas, Bernd; Berends, Boyd R

2012-02-01

Bovine intestines, bladders and oesophagus are used for the production of natural casings ("beef casings") as edible sausage containers. Derived from cattle experimentally infected with FMDV (initial dosage 10(4) TCID(50)/mL, strain A Iran 97), these beef casings were treated with sodium chloride (NaCl) or phosphate supplemented salt (P-salt). In addition, different in-vitro experiments using beef casings were done on a small scale with other FMDV strains (A Turkey 06, C-Oberbayern and O(1) Manisa) as "proof of principle". Based on the combined results of the in-vivo and in-vitro experiments, it can be concluded that the storage period of 30 days at 20 °C in NaCl is sufficiently effective to inactivate a possible contamination with FMDV in beef casings and that the usage of P-salt does not clearly enhance the inactivation of FMDV infectivity. Storage of salted beef casings at about 20 °C for 30 days is already part of the Standard Operating Procedures (included in HACCP) of the international casing industry and can therefore be considered as a protective measure for the international trade in natural casings. Copyright © 2011 Elsevier B.V. All rights reserved.

TWO-PHASE FORMATION IN SOLUTIONS OF TOBACCO MOSAIC VIRUS AND THE PROBLEM OF LONG-RANGE FORCES

PubMed Central

Oster, Gerald

1950-01-01

In a nearly salt-free medium, a dilute tobacco mosaic virus solution of rod-shaped virus particles of uniform length forms two phases; the bottom optically anisotropic phase has a greater virus concentration than has the top optically isotropic phase. For a sample containing particles of various lengths, the bottom phase contains longer particles than does the top and the concentrations top and bottom are nearly equal. The longer the particles the less the minimum concentration necessary for two-phase formation. Increasing the salt concentration increases the minimum concentration. The formation of two phases is explained in terms of geometrical considerations without recourse to the concept of long-range attractive forces. The minimum concentration for two-phase formation is that concentration at which correlation in orientation between the rod-shaped particles begins to take place. This concentration is determined by the thermodynamically effective size and shape of the particles as obtained from the concentration dependence of the osmotic pressure of the solutions measured by light scattering. The effective volume of the particles is introduced into the theory of Onsager for correlation of orientation of uniform size rods and good agreement with experiment is obtained. The theory is extended to a mixture of non-uniform size rods and to the case in which the salt concentration is varied, and agreement with experiment is obtained. The thermodynamically effective volume of the particles and its dependence on salt concentration are explained in terms of the shape of the particles and the electrostatic repulsion between them. Current theories of the hydration of proteins and of long-range forces are critically discussed. The bottom layer of freshly purified tobacco mosaic virus samples shows Bragg diffraction of visible light. The diffraction data indicate that the virus particles in solution form three-dimensional crystals approximately the size of crystalline inclusion bodies found in the cells of plants suffering from the disease. PMID:15422102

Oral salt supplements to compensate for jejunostomy losses: comparison of sodium chloride capsules, glucose electrolyte solution, and glucose polymer electrolyte solution.

PubMed

Nightingale, J M; Lennard-Jones, J E; Walker, E R; Farthing, M J

1992-06-01

Six patients with jejunostomies and residual jejunal lengths of 105 to 250 cm took the same food and water each day for eight study days. In random order, three methods of salt replacement were tested, each over 48 hours, against a period without added salt. During the three test periods the patients took 120 mmol of sodium chloride daily, as salt in gelatine capsules, as an isotonic glucose electrolyte (280 mOsmol/kg; 30 kcal) solution, and as a glucose polymer (Maxijul) solution (280 mOsmol/kg; 200 kcal). The daily stomal output remained constant for each patient during the four test periods but varied between patients from 0.60 to 2.84 kg (daily intestinal fluid balance 0.74-2.61 kg). Without a salt supplement, three patients lost more sodium from the stoma than they took in by mouth (-25, -94, and -101 mmol/day) and the mean sodium balance for all six subjects was -16 mmol (range -101 to 79) daily. Extra salt was absorbed with each form of supplement (p less than 0.05); no patient with the glucose electrolyte solution (mean 96, range 0 to 226 mmol), but one patient with the glucose-polymer solution (mean 96, range -25 to 164 mmol) and two with the salt capsules (mean 66, range -8 to 145 mmol) were in negative balance. Two patients vomited with the salt capsules. There was only a small increase in energy absorption (mean 115 kcal) with the glucose polymer solution compared with the glucose electrolyte solution. A sipped glucose electrolyte solution seems to be the optimal mode of sodium replacement in patients with a high output jejunostomy.

Oral salt supplements to compensate for jejunostomy losses: comparison of sodium chloride capsules, glucose electrolyte solution, and glucose polymer electrolyte solution.

PubMed Central

Nightingale, J M; Lennard-Jones, J E; Walker, E R; Farthing, M J

1992-01-01

Six patients with jejunostomies and residual jejunal lengths of 105 to 250 cm took the same food and water each day for eight study days. In random order, three methods of salt replacement were tested, each over 48 hours, against a period without added salt. During the three test periods the patients took 120 mmol of sodium chloride daily, as salt in gelatine capsules, as an isotonic glucose electrolyte (280 mOsmol/kg; 30 kcal) solution, and as a glucose polymer (Maxijul) solution (280 mOsmol/kg; 200 kcal). The daily stomal output remained constant for each patient during the four test periods but varied between patients from 0.60 to 2.84 kg (daily intestinal fluid balance 0.74-2.61 kg). Without a salt supplement, three patients lost more sodium from the stoma than they took in by mouth (-25, -94, and -101 mmol/day) and the mean sodium balance for all six subjects was -16 mmol (range -101 to 79) daily. Extra salt was absorbed with each form of supplement (p less than 0.05); no patient with the glucose electrolyte solution (mean 96, range 0 to 226 mmol), but one patient with the glucose-polymer solution (mean 96, range -25 to 164 mmol) and two with the salt capsules (mean 66, range -8 to 145 mmol) were in negative balance. Two patients vomited with the salt capsules. There was only a small increase in energy absorption (mean 115 kcal) with the glucose polymer solution compared with the glucose electrolyte solution. A sipped glucose electrolyte solution seems to be the optimal mode of sodium replacement in patients with a high output jejunostomy. PMID:1624155

Bath Salts Abuse Leading to New-Onset Psychosis and Potential for Violence.

PubMed

John, Michelle E; Thomas-Rozea, Crystal; Hahn, David

Bath salts have recently emerged as a popular designer drug of abuse causing significant hazardous effects on mental health and physical health, resulting in public health legislation making its usage illegal in the United States. To educate mental health providers on the effects of the new designer drug bath salts, including its potential to cause psychosis and violence in patients. This is a case report on a 40-year-old male with no past psychiatric history who presented with new-onset psychosis and increased risk for violence after ingesting bath salts. In addition, a literature review was performed to summarize the documented effects of bath salts abuse and the current U.S. public health legislation on bath salts. The presented case illustrates a new-onset, substance-induced psychotic disorder related to bath salts usage. The literature review explains the sympathomimetic reaction and the potential for psychotic symptoms. To discuss the physical and psychological effects of bath salts, treatment options for bath salts abuse and U.S. legislation by Ohio state law to current U.S. federal law that bans production, sale, and possession of main substances found in bath salts. It is important for mental health providers to be aware of bath salts, understand the physical and psychiatric effects of bath salts and be familiar with current legislative policy banning its usage. Lastly, bath salts abuse should be in the differential diagnosis where psychosis is new onset or clinically incongruent with known primary presentation of a psychotic disorder.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hadgu, Teklu; Matteo, Edward N.

An example case is presented for testing analytical thermal models. The example case represents thermal analysis of a generic repository in bedded salt at 500 m depth. The analysis is part of the study reported in Matteo et al. (2016). Ambient average ground surface temperature of 15°C, and a natural geothermal gradient of 25°C/km, were assumed to calculate temperature at the near field. For generic salt repository concept crushed salt backfill is assumed. For the semi-analytical analysis crushed salt thermal conductivity of 0.57 W/m-K was used. With time the crushed salt is expected to consolidate into intact salt. In thismore » study a backfill thermal conductivity of 3.2 W/m-K (same as intact) is used for sensitivity analysis. Decay heat data for SRS glass is given in Table 1. The rest of the parameter values are shown below. Results of peak temperatures at the waste package surface are given in Table 2.« less

Strength evolution of a reactive frictional interface is controlled by the dynamics of contacts and chemical effects

NASA Astrophysics Data System (ADS)

Renard, François; Beauprêtre, Sophie; Voisin, Christophe; Zigone, Dimitri; Candela, Thibault; Dysthe, Dag K.; Gratier, Jean-Pierre

2012-08-01

Assessing the healing rate of a fault is relevant to the knowledge of the seismic machinery. However, measuring fault healing at the depths where it occurs still remains inaccessible. We have designed an analog laboratory experiment of a simulated rough fault that undergoes healing and investigate the relative roles of interface chemical reactivity and sliding velocity on the healing rate. Slide-hold-slide experiments are conducted on a bare interface with various materials in contact (glass/glass, salt/glass, and salt/salt) with or without the presence of a reactive fluid and the slider-surface pull-off force is measured. Our results show that the interface strengthens with hold time, whatever the conditions of the experiments. In addition, we quantify the effect of chemical reactivity on the healing rate. Considering the glass/glass case as a reference, we show that the healing rate is increased by a factor of 2 for the salt/glass case; by a factor of 3 for the salt/salt case; and by about a factor of 20 when saturated brine is added on a salt/salt interface. We also measure that the sliding velocity affects the healing rate for salt/salt interfaces at room humidity. A careful optical monitoring of the interface allows a direct observation of the contact growth characteristics associated to each type of materials. Finally, the large differences of healing rate are interpreted through a mechanistic approach, where the various experimental conditions allow separating different healing mechanisms: increase of adhesion of the contacts by welding, contact growth due to creep or due to neck growth driven by surface tension.

The preparation and evaluation of salt forms of linogliride with reduced solubilities as candidates for extended release.

PubMed

Chrzanowski, Frank A; Ahmad, Kaleem

2017-03-01

Salts of linogliride with reduced solubilities were prepared and evaluated as potential candidates for extended-release oral dosage forms. A once-daily dose of 300-800 mg was intended. Seven acids were selected: p-acetamidobenzoic, benzoic, p-hydroxybenzoic, 3-hydroxy-2-naphthoic, 1-napsylic, pamoic, and p-toluenesulfonic acids but only four salts were able to be prepared in suitable quantities for evaluation: linogliride pamoate, p-hydroxybenzoate, 3-hydroxy-2-naphthoate, and 1-napsylate. The pH-solubility profiles of the four new salts, free base, and fumarate salt were compared over the pH 1.43-8.3 range and the intrinsic dissolution rates of the four new salts and the free base were determined at pH 1.43, 4.4, and 7.5. The range of the pH-solubility profile and intrinsic dissolution rates of the p-hydroxybenzoate salt were less than the free base and fumarate and higher than the other three new salts. The pH-solubilities and intrinsic dissolution rates of the 1-napsylate salt were pH-independent. The solubilities and intrinsic dissolution rates of the pamoate and 3-hydroxy-2-naphthoate were higher at pH 1.4-3.4 than at higher pH. At pH 4.4 and higher, the solubilities were essentially the same, in the 1-2 mg/mL range. The intrinsic dissolution rates were also very low and not very different. Dissolution studies with capsules containing 800 mg doses of the pamoate, 1-napsylate, free base, and fumarate performed in a dissolution medium of pH beginning at 2.2 and ending at 6.8 demonstrated that the pamoate and 1-napsylate salt forms dissolved slower and could be useful as extended-release forms.

Individual aerosol particles in and below clouds along a Mt. Fuji slope: Modification of sea-salt-containing particles by in-cloud processing

NASA Astrophysics Data System (ADS)

Ueda, S.; Hirose, Y.; Miura, K.; Okochi, H.

2014-02-01

Sizes and compositions of atmospheric aerosol particles can be altered by in-cloud processing by absorption/adsorption of gaseous and particulate materials and drying of aerosol particles that were formerly activated as cloud condensation nuclei. To elucidate differences of aerosol particles before and after in-cloud processing, aerosols were observed along a slope of Mt. Fuji, Japan (3776 m a.s.l.) during the summer in 2011 and 2012 using a portable laser particle counter (LPC) and an aerosol sampler. Aerosol samples for analyses of elemental compositions were obtained using a cascade impactor at top-of-cloud, in-cloud, and below-cloud altitudes. To investigate composition changes via in-cloud processing, individual particles (0.5-2 μm diameter) of samples from five cases (days) collected at different altitudes under similar backward air mass trajectory conditions were analyzed using a transmission electron microscope (TEM) equipped with an energy dispersive X-ray analyzer. For most cases (four cases), most particles at all altitudes mainly comprised sea salts: mainly Na with some S and/or Cl. Of those, in two cases, sea-salt-containing particles with Cl were found in below-cloud samples, although sea-salt-containing particles in top-of-cloud samples did not contain Cl. This result suggests that Cl in the sea salt was displaced by other cloud components. In the other two cases, sea-salt-containing particles on samples at all altitudes were without Cl. However, molar ratios of S to Na (S/Na) of the sea-salt-containing particles of top-of-cloud samples were higher than those of below-cloud samples, suggesting that sulfuric acid or sulfate was added to sea-salt-containing particles after complete displacement of Cl by absorption of SO2 or coagulation with sulfate. The additional volume of sulfuric acid in clouds for the two cases was estimated using the observed S/Na values of sea-salt-containing particles. The estimation revealed that size changes by in-cloud processing from below-cloud to top-of-cloud altitudes were less than 6% for sizes of 0.5-2 μm diameter. The obtained results will be useful to evaluate the aging effect and transition of aerosol particles through in-cloud processing.

Injection-salting of pre rigor fillets of Atlantic salmon (Salmo salar).

PubMed

Birkeland, Sveinung; Akse, Leif; Joensen, Sjurdur; Tobiassen, Torbjørn; Skåra, Torstein

2007-01-01

The effects of temperature (-1, 4, and 10 degrees C), brine concentration (12% and 25% NaCl), injection volumes, and needle densities were investigated on fillet weight gain (%), salt content (%), fillet contraction (%), and muscle gaping in pre rigor brine-injected fillets of Atlantic salmon (Salmo salar). Increased brine concentration (12% to 25%) significantly increased the initial (< 5 min after injection) and final contraction (24 h after injection) of pre rigor fillets. Increased brine concentration significantly reduced weight gain and increased salt content but had no significant effect on muscle gaping. The temperatures tested did not significantly affect weight gain, fillet contraction, or gaping score. Significant regressions (P < 0.01) between the injection volume and weight gain (range: 2.5% to 15.5%) and salt content (range: 1.7% to 6.5%) were observed for injections of pre rigor fillets. Double injections significantly increased the weight gain and salt content compared to single injections. Initial fillet contraction measured 30 min after brine injection increased significantly (P < 0.01) with increasing brine injection volume but no significant difference in the fillet contraction was observed 12 h after brine injection (range: 7.9% to 8.9%). Brine-injected post rigor control fillets obtained higher weight gain, higher salt content, more muscle gaping, and significantly lower fillet contraction compared to the pre rigor injected fillets. Injection-salting is an applicable technology as a means to obtain satisfactory salt contents and homogenously distribute the salt into the muscle of pre rigor fillets of Atlantic salmon before further processing steps such as drying and smoking.

Skin Sensitizing Potency of Halogenated Platinum Salts.

EPA Science Inventory

The relationship between occupational exposure to halogenated platinum (Pt) salts and Pt-specific allergic sensitization is well-established. Although human case reports and clinical studies demonstrate that Pt salts are potent skin sensitizers, no studies have been published tha...

Salt-dome-related diagenesis of Miocene sediment, Black Bayou field, Cameron Parish, Louisiana

DOE Office of Scientific and Technical Information (OSTI.GOV)

Leger, W.R.

1988-09-01

The Black Bayou field is associated with a salt dome that pierces Miocene sediment and rises to within 900 ft (275 m) of the surface. The Louisiana Gulf Coast regional geothermal gradient is locally affected by the salt dome. The gradient increases to values greater than the regional gradient, 1.26/degrees/F/100 ft (23/degrees/C/km), near the dome. Local effects of the salt dome on clastic diagenesis have been determined by studying sandstone samples adjacent to and away from the salt dome within Miocene sediment. Sample depths range from 4155 to 6145 ft (1266 to 1873 m). Distances of samples from the edgemore » of the dome range from 82 to 820 ft (25 to 250 m).« less

View of the Salt Lake City, Utah area

NASA Technical Reports Server (NTRS)

1973-01-01

An oblique view of the Salt Lake City, Utah area as photographed from Earth orbit by one of the six lenses of the Itek-furnished S190-A Multispectral Photographic Facility Experiment aboard the Skylab space station. Approximately two-thirds of the Great Salt Lake is in view. The smaller body of water south of Salt Lake City is Utah Lake. The Wasatch Range is on the east side of the Great Salt Lake.

Method for preparing salt solutions having desired properties

DOEpatents

Ally, Moonis R.; Braunstein, Jerry

1994-01-01

The specification discloses a method for preparing salt solutions which exhibit desired thermodynamic properties. The method enables prediction of the value of the thermodynamic properties for single and multiple salt solutions over a wide range of conditions from activity data and constants which are independent of concentration and temperature. A particular application of the invention is in the control of salt solutions in a process to provide a salt solution which exhibits the desired properties.

Distinctive styles of salt deformation formed by radial, convergent gliding into the sharp corners of the northeastern and northwestern Gulf of Mexico

NASA Astrophysics Data System (ADS)

Bugti, M. N.; Mann, P.

2016-12-01

Previous workers have described the effects both downslope motion of salt and shale along straight margins and the more complex three-dimensional cases of downslope salt motion and deformation: 1) radial, divergent gliding off of coastal salients accompanied by strike-parallel extension increasing downslope; and 2) radial, convergent gliding into coastal reentrants or "corners" accompanied by strike-parallel contraction and differential loading increasing downslope. The northwestern Gulf of Mexico (GOM) forms a sharp, right-angle corner defined northeastern shelf of Mexico and South Texas and the shelf of the northern GOM; in a similar way the northwestern GOM forms a sharp, right-angle corner defined by the northern shelf of the GOM and the shelf of west Florida. Despite their physical separation by over 700 km, both the NW and NE GOM corners exhibit similar salt structures not observed in adjacent areas outside of the two corners. These corner-related features include: 1) detached salt stocks with positive surface expression; we interpret the detached salt stocks as reflecting a higher degree of radial convergent gliding and compression from three sides into the bend areas; 2) slightly elongate, surficial, diapir shapes with positive bathymetric expression and ranging in diameter from 2 to 22 km and localized fold axes with the long diapiric axes and fold axes aligned parallel to the bisector of the bend; these features are also attributed to radial convergent gliding into the bend areas; 3) zones of deformation at depth that occupy the corner areas: the northwestern GOM corresponds to the Port Isabel passive-margin fold and thrust belt and the northeastern GOM corresponds to the Mississippi Canyon fold and thrust belt; while these are older convergent features we propose that they are being reactivated by the corner-centric, gravity-driven process of radial, convergent gliding; and 4) salt welds in both corner areas record more intensive and complete salt extrusion of salt; outside the corner areas salt canopies and the lack of salt welds indicates a less convergent environment for salt. These two proposed areas of radial convergent gliding are compared to other examples of radial, convergent gliding described by previous workers in the Gulf of Lions and Santos basins.

Applications of the low-background gamma spectroscopy to the geographical origin of marine salts and prunes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Perrot, F.

The low background gamma spectroscopy has been applied to try to sign the geographical origin of the French atlantic marine salts and of the prunes from Agen. Most of the activity measurements have been done using low background Ge spectrometers located in Bordeaux. Results have shown that a clear signature exists in the case of the French atlantic salts using the 40K, 137Cs and 226Ra isotopes but not in the case of the prunes.

A Safety Case Approach for Deep Geologic Disposal of DOE HLW and DOE SNF in Bedded Salt - 13350

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sevougian, S. David; MacKinnon, Robert J.; Leigh, Christi D.

2013-07-01

The primary objective of this study is to investigate the feasibility and utility of developing a defensible safety case for disposal of United States Department of Energy (U.S. DOE) high-level waste (HLW) and DOE spent nuclear fuel (SNF) in a conceptual deep geologic repository that is assumed to be located in a bedded salt formation of the Delaware Basin [1]. A safety case is a formal compilation of evidence, analyses, and arguments that substantiate and demonstrate the safety of a proposed or conceptual repository. We conclude that a strong initial safety case for potential licensing can be readily compiled bymore » capitalizing on the extensive technical basis that exists from prior work on the Waste Isolation Pilot Plant (WIPP), other U.S. repository development programs, and the work published through international efforts in salt repository programs such as in Germany. The potential benefits of developing a safety case include leveraging previous investments in WIPP to reduce future new repository costs, enhancing the ability to effectively plan for a repository and its licensing, and possibly expediting a schedule for a repository. A safety case will provide the necessary structure for organizing and synthesizing existing salt repository science and identifying any issues and gaps pertaining to safe disposal of DOE HLW and DOE SNF in bedded salt. The safety case synthesis will help DOE to plan its future R and D activities for investigating salt disposal using a risk-informed approach that prioritizes test activities that include laboratory, field, and underground investigations. It should be emphasized that the DOE has not made any decisions regarding the disposition of DOE HLW and DOE SNF. Furthermore, the safety case discussed herein is not intended to either site a repository in the Delaware Basin or preclude siting in other media at other locations. Rather, this study simply presents an approach for accelerated development of a safety case for a potential DOE HLW and DOE SNF repository using the currently available technical basis for bedded salt. This approach includes a summary of the regulatory environment relevant to disposal of DOE HLW and DOE SNF in a deep geologic repository, the key elements of a safety case, the evolution of the safety case through the successive phases of repository development and licensing, and the existing technical basis that could be used to substantiate the safety of a geologic repository if it were to be sited in the Delaware Basin. We also discuss the potential role of an underground research laboratory (URL). (authors)« less

Sol-Gel transition behavior of pure iota-carrageenan in both salt-free and added salt states.

PubMed

Hossain, K S; Miyanaga, K; Maeda, H; Nemoto, N

2001-01-01

This paper describes how strongly the gelation process of iota-carrageenan is affected by addition of metallic ions from the creep and creep recovery, dynamic viscoelasticity (DVE) and DSC measurements. Creep results at T = 25 degrees C indicate that below a polymer concentration C of 3.0 wt % the salt-free system behaves as a viscous solution, and it starts to exhibit viscoelasticity as C exceeds 3.0 wt %. In the range C = 5.0-7.0 wt %, the salt-free system shows gellike behavior whereas the added salt system, measured in the low C range 1.0-2.5 wt %, showed gellike behavior at the same temperature. The sol-gel transition temperature T(c) was determined using Winter's criterion as the temperature at which both G'(omega) and G' '(omega) follow power law behavior with the same exponent n. DSC measurements reveal that salt-free and added salt systems take different types of thermal behavior within the same temperature range. The temperature T(c) is quite close to the gelation temperature T(m) determined from DSC measurement. The Eldrige-Ferry plot was performed to estimate activaton enthalpy, which shows that physical cross-links in the salt-free iota-carrageenan is not strong in comparison with those of samples which contains metal ions. We conclude from the data analysis of C dependence of the plateau modulus using the theory developed by Jones and Marques for rigid networks based on the fractal theories that addition of metallic ions gives rise to a rigid fiber like structure even at low C of iota-carrageenan in contrast to the salt-free system for which a flexible structure has been maintained at higher C.

Extraction and LC determination of lysine clonixinate salt in water/oil microemulsions.

PubMed

Pineros, I; Ballesteros, P; Lastres, J L

2002-02-01

A new reversed-phase high performance liquid chromatography method has been developed and validated for the quantitative determination of lysine clonixinate salt in water/oil microemulsions. The mobile phase was acetonitrile-buffer phosphate pH 3.3. Detection was UV absorbance at 252 nm. The precision and accurately of the method were excellent. The established linearity range was 5-60 microg ml(-1) (r(2)=0.999). Microemulsions samples were dispersed with chloroform and extracted lysine clonixinate salt with water. This easy method employing chloroformic extraction has been done three times. The recovery of lysine clonixinate salt from spiked placebo and microemulsion were >90% over the linear range.

Heat transfer and pressure drop measurements in an air/molten salt direct-contact heat exchanger

NASA Astrophysics Data System (ADS)

Bohn, Mark S.

1988-11-01

This paper presents a comparison of experimental data with a recently published model of heat exchange in irrigated packed beds. Heat transfer and pressure drop were measured in a 150 mm (ID) column with a 610 mm bed of metal Pall rings. Molten nitrate salt and preheated air were the working fluids with a salt inlet temperature of approximately 440 C and air inlet temperatures of approximately 230 C. A comparison between the experimental data and the heat transfer model is made on the basis of heat transfer from the salt. For the range of air and salt flow rates tested, 0.3 to 1.2 kg/sq m/s air flow and 6 to 18 kg/sq m/s salt flow, the data agree with the model within 22 percent standard deviation. In addition, a model for the column pressure drop was validated, agreeing with the experimental data within 18 percent standard deviation over the range of column pressure drop from 40 to 1250 Pa/m.

Properties and heat transfer coefficients of four molten-salt high temperature heat transfer fluid candidates for concentrating solar power plants

NASA Astrophysics Data System (ADS)

Liu, T. L.; Liu, W. R.; Xu, X. H.

2017-11-01

Heat transfer fluid is one critical component for transferring and storing heat energy in concentrating solar power systems. Molten-salt mixtures can be used as high temperature heat transfer fluids because of their thermophysical properties. This paper studied the thermophysical properties of Li2CO3-Na2CO3-K2CO3 eutectic salt and three eutectic chloride salts NaCl-KCl-ZnCl2 with different compositions in the range of 450-600°C and 250-800°C, respectively. Properties including specific heat capacity, thermal conductivity, density and viscosity were determined based on imperial correlations and compared at different operating temperatures. The heat transfer coefficients of using different eutectic salts as heat transfer fluids were also calculated and compared in their operating temperature range. It is concluded that all the four eutectic salts can satisfy the requirements of a high-temperature heat transfer fluid.

Dielectric dispersion of short single-stranded DNA in aqueous solutions with and without added salt.

PubMed

Katsumoto, Yoichi; Omori, Shinji; Yamamoto, Daisuke; Yasuda, Akio; Asami, Koji

2007-01-01

Dielectric spectroscopy measurements were performed for aqueous solutions of short single-stranded DNA with 30 to 120 bases of thymine over a frequency range of 10;{5} to 10;{8}Hz . Dielectric dispersion was found to include two relaxation processes in the ranges from 10;{5} to 10;{6} and from 10;{6} to 10;{8}Hz , respectively, with the latter mainly discussed in this study. The dielectric increment and the relaxation time of the high-frequency relaxation of DNA in solutions without added salt exhibited concentration and polymer-length dependences eventually identical to those for dilute polyion solutions described in previous studies. For solutions with added salt, on the other hand, those dielectric parameters were independent of salt concentration up to a certain critical value and started to decrease with further increasing salt concentration. This critical behavior is well explained by our newly extended cell model that takes into account the spatial distribution of loosely bound counterions around DNA molecules as a function of salt concentration.

Soil Carbon Stocks in a Shifting Ecosystem; Climate Induced Migration of Mangroves into Salt Marsh

NASA Astrophysics Data System (ADS)

Simpson, L.; Osborne, T.; Feller, I. C.

2015-12-01

Across the globe, coastal wetland vegetation distributions are changing in response to climate change. The increase in global average surface temperature has already caused shifts in the structure and distribution of many ecological communities. In parts of the southeastern United States, increased winter temperatures have resulted in the poleward range expansion of mangroves at the expense of salt marsh habitat. Our work aims to document carbon storage in the salt marsh - mangrove ecotone and any potential changes in this reservoir that may ensue due to the shifting range of this habitat. Differences in SOM and C stocks along a latitudinal gradient on the east coast of Florida will be presented. The gradient studied spans 342 km and includes pure mangrove habitat, the salt marsh - mangrove ecotone, and pure salt marsh habitat.This latitudinal gradient gives us an exceptional opportunity to document and investigate ecosystem soil C modifications as mangroves transgress into salt marsh habitat due to climatic change.

Method for making fine and ultrafine spherical particles of zirconium titanate and other mixed metal oxide systems

DOEpatents

Hu, Michael Z.

2006-05-23

Disclosed is a method for making amorphous spherical particles of zirconium titanate and crystalline spherical particles of zirconium titanate comprising the steps of mixing an aqueous solution of zirconium salt and an aqueous solution of titanium salt into a mixed solution having equal moles of zirconium and titanium and having a total salt concentration in the range from 0.01 M to about 0.5 M. A stearic dispersant and an organic solvent is added to the mixed salt solution, subjecting the zirconium salt and the titanium salt in the mixed solution to a coprecipitation reaction forming a solution containing amorphous spherical particles of zirconium titanate wherein the volume ratio of the organic solvent to aqueous part is in the range from 1 to 5. The solution of amorphous spherical particles is incubated in an oven at a temperature .ltoreq.100.degree. C. for a period of time .ltoreq.24 hours converting the amorphous particles to fine or ultrafine crystalline spherical particles of zirconium titanate.

Petro-elastic modelling and characterization of solid-filled reservoirs: Comparative analysis on a Triassic North Sea reservoir

NASA Astrophysics Data System (ADS)

Auduson, Aaron E.

2018-07-01

One of the most common problems in the North Sea is the occurrence of salt (solid) in the pores of Triassic sandstones. Many wells have failed due to interpretation errors based conventional substitution as described by the Gassmann equation. A way forward is to device a means to model and characterize the salt-plugging scenarios. Modelling the effects of fluid and solids on rock velocity and density will ascertain the influence of pore material types on seismic data. In this study, two different rock physics modelling approaches are adopted in solid-fluid substitution, namely the extended Gassmann theory and multi-mineral mixing modelling. Using the modified new Gassmann equation, solid-and-fluid substitutions were performed from gas or water filling in the hydrocarbon reservoirs to salt materials being the pore-filling. Inverse substitutions were also performed from salt-filled case to gas- and water-filled scenarios. The modelling results show very consistent results - Salt-plugged wells clearly showing different elastic parameters when compared with gas- and water-bearing wells. While the Gassmann equation-based modelling was used to discretely compute effective bulk and shear moduli of the salt plugs, the algorithm based on the mineral-mixing (Hashin-Shtrikman) can only predict elastic moduli in a narrow range. Thus, inasmuch as both of these methods can be used to model elastic parameters and characterize pore-fill scenarios, the New Gassmann-based algorithm, which is capable of precisely predicting the elastic parameters, is recommended for use in forward seismic modelling and characterization of this reservoir and other reservoir types. This will significantly help in reducing seismic interpretation errors.

Cost and health consequences of reducing the population intake of salt

PubMed Central

Selmer, R.; Kristiansen, I. S.; Haglerod, A.; Graff-Iversen, S.; Larsen, H.; Meyer, H.; Bonaa, K.; Thelle, D.

2000-01-01

STUDY OBJECTIVE—The aim was to estimate health and economic consequences of interventions aimed at reducing the daily intake of salt (sodium chloride) by 6 g per person in the Norwegian population. Health promotion (information campaigns), development of new industry food recipes, declaration of salt content in food and taxes on salty food/subsidies of products with less salt, were possible interventions.
DESIGN—The study was a simulation model based on present age and sex specific mortality in Norway and estimated impact of blood pressure reductions on the risks of myocardial infarction and stroke as observed in Norwegian follow up studies. A reduction of 2 mm Hg systolic blood pressure (range 1-4) was assumed through the actual interventions. The cost of the interventions in themselves, welfare losses from taxation of salty food/subsidising of food products with little salt, cost of avoided myocardial infarction and stroke treatment, cost of avoided antihypertensive treatment, hospital costs in additional life years and productivity gains from reduced morbidity and mortality were included.
RESULTS—The estimated increase in life expectancy was 1.8 months in men and 1.4 in women. The net discounted (5%) cost of the interventions was minus $118 millions (that is, cost saving) in the base case. Sensitivity analyses indicate that the interventions would be cost saving unless the systolic blood pressure reduction were less than 2 mm Hg, productivity gains were disregarded or the welfare losses from price interventions were high.
CONCLUSION—Population interventions to reduce the intake of salt are likely to improve the population's health and save costs to society.


Keywords: sodium; hypertension; cost effectiveness PMID:10942450

A geomechanical model of a sinkhole formation

NASA Astrophysics Data System (ADS)

Danchiv, Alexandru; Zamfirescu, Florian; Mocuta, Marius; Popa, Iulian; Zlibut, Alexandru; Huggenberger, Peter; Zechner, Eric; Dresmann, Horst; Scheidler, Stefan; Wiesmeier, Stefan

2016-04-01

On December 2010 a sinkhole was suddenly formed close to the eastern flank of Ocna-Mures salt dome. Soon after the collapse the sinkhole was filled with brine forming a salt lake called Plus Lake. The total volume of sinkhole of about 100000 m3 remained constant since February 2011. The Ocna Mures salt dome is situated on the western border of the Transylvanian basin (Romania) and has been exploited for a long time. The ceilings of some shallow mine chambers are now collapsed and filled with brine. Along the eastern flank of the salt dome there is a disturbed zone due to diapirism. Its presence is suggested by the strong fragmentation of rock in the boreholes drilled along the salt-sterile contact, as it resulted from the low values of RQD index. The sinkhole is probably due to a pressure increase along the diapir flank. The causes of this sudden increase of pressure are not well known. Most probably it is due to the damage of the tubing of a flank borehole as mentioned in a technical report of the exploiting company. The injected fresh water expelled through the breaches of the damaged borehole and, due to the high pressure flushed up the crushed material of the disturbed zone. In order to better understand the setting up of the Plus Lake joint research efforts were performed by teams from Bucharest and Basel Universities since 2013. For the geomechanical approach a numerical model was performed using the Flac 7.0 code. In a first stage the creep behavior of salt was analyzed considering a Norton creep law. It resulted that after 100 years the salt reached equilibrium, the creep could be neglected and in a first approximation mechanical equilibrium could be analyzed considering only an elasto-plastic behavior of both the salt and the sterile. For both the salt and the surrounding sedimentary rocks the Mohr-Coulomb criterion was considered. The properties of sterile rocks were estimated following the GSI system. Due to poor rock quality the strength parameters have very low values, with a cohesion within a range from 0.167 to 0.46 MPa and a friction angle in a range between 1.05 and 4.5 degrees. As a result the global safety factor is strongly diminished, to values close to 1. In this case the rock mass exceeds the limit for equilibrium and will collapse. Also the maximum shear strain rate is concentrated in a narrow zone which delineates a disequilibrium prism, which according to the velocity vectors is sliding to the old mine chambers. Thus, after the collapse of the prism the rock mass will enter into the old mine chambers and the expelled brine will form the Plus Lake.

The 2-D Ion Chromatography Development and Application: Determination of Sulfate in Formation Water at Pre-Salt Region

NASA Astrophysics Data System (ADS)

Tonietto, G. B.; Godoy, J. M.; Almeida, A. C.; Mendes, D.; Soluri, D.; Leite, R. S.; Chalom, M. Y.

2015-12-01

Formation water is the naturally-occurring water which is contained within the geological formation itself. The quantity and quality of the formation water can both be problematic. Over time, the water volume should decrease as the gas volumes increase. Formation water has been found to contain high levels of Cl, As, Fe, Ba, Mn, PAHs and may even contain naturally occurring radioactive materials. Chlorides in some cases have been found to be in excess of four-five times the level of concentrations found in the ocean. Within the management of well operation, there is sulfate between the analytes of greatest importance due to the potential for hydrogen sulphide formation and consequent corrosion of pipelines. As the concentration of sulfate in these waters can be less than n times that of chloride, a quantitative determination, using the technique of ion chromatography, constitutes an analytical challenge. This work aimed to develop and validate a method for the determination of sulphate ions in hyper-saline waters coming from the oil wells of the pre-salt, using 2D IC. In 2D IC the first column can be understood as a separating column, in which the species with retention times outside a preset range are discarded, while those belonging to this range are retained in a pre-concentrator column to further injecting a second column, the second dimension in which occurs the separation and quantification of the analytes of interest. As the chloride ions have a retention time lower than that of sulfate, a method was developed a for determining sulfate in very low range (mg L-1) by 2D IC, applicable to hypersaline waters, wherein the first dimension is used to the elimination of the matrix, ie, chloride ions, and the second dimension utilized in determining sulfate. For sulphate in a concentration range from 1.00 mg L-1 was obtained an accuracy of 1.0%. The accuracy of the method was tested by the standard addition method different samples of formation water in the pre-salt region, having been a relative error less than 1.0% at a concentration of 5.0 mg L-1.This work allowed the expected achievement of sulfate results for hyper-saline samples such as those found in the pre-salt exploration. Studies are being developed in order to validate the determination of bromide in the pre-salt water, using the 2D liquid chromatography.

Adding Salt to Meals as a Risk Factor of Type 2 Diabetes Mellitus: A Case-Control Study.

PubMed

Radzeviciene, Lina; Ostrauskas, Rytas

2017-01-13

Type 2 diabetes mellitus (T2DM) is thought to arise from the complex interplay between genetic and environmental factors. It is important to identify modifiable risk factors that may help to reduce the risk of diabetes. Data on salt intake and the risk of type 2 diabetes are limited. The aim of this study was to assess the relationship between adding salt to prepared meals and the risk of type 2 diabetes. In a case-control study, we included 234 cases, all of whom were patients aged 35-86 years with a newly confirmed diagnosis of T2DM, and 468 controls that were free of the disease. Cases and controls (ratio 1:2) were matched by gender and age (±5 years). A questionnaire was used to collect information on possible risk factors for diabetes. Adding salt to prepared meals was assessed according to: Never, when there was not enough, or almost every time without tasting. The odds ratios (OR), and 95% confidence intervals (CI) for type 2 diabetes was calculated using a conditional logistic regression. The cases had a higher body mass index and a significantly lower education level compared to the controls. Variables such as waist circumference, body mass index, eating speed, smoking, family history of diabetes, arterial hypertension, plasma triglycerides, educational level, occupational status, morning exercise, marital status, daily urine sodium excretion, and daily energy intake were retained in the models as confounders. After adjusting for possible confounders, an approximately two-fold increased risk of type 2 diabetes was determined in subjects who add salt to prepared meals when "it is not enough" or "almost every time without tasting" (1.82; 95% CI 1.19-2.78; p = 0.006) compared with never adding salt. Presented data suggest the possible relationship between additional adding of salt to prepared meals and an increased risk of type 2 diabetes.

Avast Ye Salty Dogs: Salt damage in the context of coastal residential construction and historical maritime timbers

Treesearch

Grant T. Kirker; Samuel L. Zelinka; Leandro Passarini

2016-01-01

Salt damage is a frequent problem in wood exposed to seawater and other saline environments. Symptoms of salt damage are often referred to as fuzzy wood and have been historically considered non-structural damage, but a growing number of customer inquiries have prompted a re-evaluation of this phenomenon. This paper details several case studies involving salt damage,...

Organic Electrochemistry in Aluminum Chloride Melts.

DTIC Science & Technology

1976-08-15

establishing a new, room temperature molten salt system. The low temperature fused salt was prepared by combining aluminum...narrow (600 mY) potential range. Organic electrosynthesis was conducted in a 50-50 by volume molten salt - benzene solution. This mixed solvent...room temperature molten salt system, namely a 67:33 mole percent aluminum chloride: ethylpyridinium bromide melt and in a 50-50 by volume solution of the

RIGOR MORTIS AND THE INFLUENCE OF CALCIUM AND MAGNESIUM SALTS UPON ITS DEVELOPMENT.

PubMed

Meltzer, S J; Auer, J

1908-01-01

Calcium salts hasten and magnesium salts retard the development of rigor mortis, that is, when these salts are administered subcutaneously or intravenously. When injected intra-arterially, concentrated solutions of both kinds of salts cause nearly an immediate onset of a strong stiffness of the muscles which is apparently a contraction, brought on by a stimulation caused by these salts and due to osmosis. This contraction, if strong, passes over without a relaxation into a real rigor. This form of rigor may be classed as work-rigor (Arbeitsstarre). In animals, at least in frogs, with intact cords, the early contraction and the following rigor are stronger than in animals with destroyed cord. If M/8 solutions-nearly equimolecular to "physiological" solutions of sodium chloride-are used, even when injected intra-arterially, calcium salts hasten and magnesium salts retard the onset of rigor. The hastening and retardation in this case as well as in the cases of subcutaneous and intravenous injections, are ion effects and essentially due to the cations, calcium and magnesium. In the rigor hastened by calcium the effects of the extensor muscles mostly prevail; in the rigor following magnesium injection, on the other hand, either the flexor muscles prevail or the muscles become stiff in the original position of the animal at death. There seems to be no difference in the degree of stiffness in the final rigor, only the onset and development of the rigor is hastened in the case of the one salt and retarded in the other. Calcium hastens also the development of heat rigor. No positive facts were obtained with regard to the effect of magnesium upon heat vigor. Calcium also hastens and magnesium retards the onset of rigor in the left ventricle of the heart. No definite data were gathered with regard to the effects of these salts upon the right ventricle.

RIGOR MORTIS AND THE INFLUENCE OF CALCIUM AND MAGNESIUM SALTS UPON ITS DEVELOPMENT

PubMed Central

Meltzer, S. J.; Auer, John

1908-01-01

Calcium salts hasten and magnesium salts retard the development of rigor mortis, that is, when these salts are administered subcutaneously or intravenously. When injected intra-arterially, concentrated solutions of both kinds of salts cause nearly an immediate onset of a strong stiffness of the muscles which is apparently a contraction, brought on by a stimulation caused by these salts and due to osmosis. This contraction, if strong, passes over without a relaxation into a real rigor. This form of rigor may be classed as work-rigor (Arbeitsstarre). In animals, at least in frogs, with intact cords, the early contraction and the following rigor are stronger than in animals with destroyed cord. If M/8 solutions—nearly equimolecular to "physiological" solutions of sodium chloride—are used, even when injected intra-arterially, calcium salts hasten and magnesium salts retard the onset of rigor. The hastening and retardation in this case as well as in the cases of subcutaneous and intravenous injections, are ion effects and essentially due to the cations, calcium and magnesium. In the rigor hastened by calcium the effects of the extensor muscles mostly prevail; in the rigor following magnesium injection, on the other hand, either the flexor muscles prevail or the muscles become stiff in the original position of the animal at death. There seems to be no difference in the degree of stiffness in the final rigor, only the onset and development of the rigor is hastened in the case of the one salt and retarded in the other. Calcium hastens also the development of heat rigor. No positive facts were obtained with regard to the effect of magnesium upon heat vigor. Calcium also hastens and magnesium retards the onset of rigor in the left ventricle of the heart. No definite data were gathered with regard to the effects of these salts upon the right ventricle. PMID:19867124

A 9-state analysis of designer stimulant, "bath salt," hospital visits reported to poison control centers.

PubMed

Warrick, Brandon J; Hill, Meredith; Hekman, Kimberly; Christensen, Rachelle; Goetz, Robert; Casavant, Marcel J; Wahl, Michael; Mowry, James B; Spiller, Henry; Anderson, Deborah; Aleguas, Alfred; Gummin, David; Thomas, Ronald; Nezlek, Christopher; Smolinske, Susan

2013-09-01

A new generation of designer stimulants marketed as "bath salts" emerged in late 2010. The goal is to describe the epidemiologic emergence of designer stimulants in 9 states in the Midwest. A retrospective review of the National Poison Data System was performed between November 1, 2010, and November 30, 2011. Inclusion criteria were health care-evaluated bath salts or other synthetic stimulants exposures. Cases were excluded if the exposure was unrelated to a designer stimulant. Demographic and clinical characteristics of cases were calculated and differences in outcome and exposure by generation were examined. One thousand six hundred thirty-three patients met the inclusion criteria. Age ranged from 1 day to 61 years (mean=29.2 years), with 67.9% male patients. The most common clinical features were agitation (62.2%), tachycardia (55.2%), and hallucinations (32.7%). In addition to 15.5% of patients having a major medical effect, 0.6% died. Reason for use was primarily intentional abuse (88.5%). However, 0.7% of patients reported withdrawal. Treatment involved primarily benzodiazepines (58.5%), with 8.7% of patients being intubated. Baby Boomers were more likely to have a major medical outcome (24.2%) and to report injection as the method of administration (8.6%-12.9%). Synthetic stimulants rapidly swept across the Midwest, resulting in more than 1,600 patients seeking medical care. Serious medical effects or death was observed in 16.1% of cases. Older generations were more likely to inject and to have a major medical outcome. Copyright © 2013 American College of Emergency Physicians. Published by Mosby, Inc. All rights reserved.

Stability of pharmaceutical salts in solid oral dosage forms.

PubMed

Nie, Haichen; Byrn, Stephen R; Zhou, Qi Tony

2017-08-01

Using pharmaceutical salts in solid dosage forms can raise stability concerns, especially salt dissociation which can adversely affect the product performance. Therefore, a thorough understanding of the salt instability encountered in solid-state formulations is imperative to ensure the product quality. The present article uses the fundamental theory of acid base, ionic equilibrium, relationship of pH and solubility as a starting point to illustrate and interpret the salt formation and salt disproportionation in pharmaceutical systems. The criteria of selecting the optimal salt form and the underlying theory of salt formation and disproportionation are reviewed in detail. Factors influencing salt stability in solid dosage forms are scrutinized and discussed with the case studies. In addition, both commonly used and innovative strategies for preventing salt dissociations in formulation, on storage and during manufacturing will be suggested herein. This article will provide formulation scientists and manufacturing engineers an insight into the mechanisms of salt disproportionation and salt formation, which can help them to avoid and solve the instability issues of pharmaceutical salts in the product design.

Vulnerability of Rhode Island Salt Marshes to Sea Level Rise and Poor Water Quality

EPA Science Inventory

Across the northeastern Unites States, salt marshes are losing ground. Edges are eroding, tidal channel networks are expanding, and new ponds are forming and expanding within salt marshes. This leaves shorelines - and in some cases houses - more vulnerable to nor'easters and tr...

Assessing Wildlife Habitat Value of New England Salt Marshes: II. Model Testing and Validation

EPA Science Inventory

We test a previously described model to assess the wildlife habitat value of New England salt marshes by comparing modeled habitat values and scores with bird abundance and species richness at sixteen salt marshes in Narragansett Bay, Rhode Island USA. Assessment scores ranged f...

Secondary Aluminum Processing Waste: Salt Cake Characterization and Reactivity

EPA Science Inventory

Thirty-nine salt cake samples were collected from 10 SAP facilities across the U.S. The facilities were identified by the Aluminum Association to cover a wide range of processes. Results suggest that while the percent metal leached from the salt cake was relatively low, the leac...

IMPACTS OF NITROGEN LOADING ON SALT MARSH INTEGRITY IN NEW ENGLAND, USA

EPA Science Inventory

Salt marsh habitat integrity is linked with the ability to provide good water quality and high biodiversity. We measured high denitrification enzyme activity (DEA) in ten coastal salt marshes in Narragansett Bay, Rhode Island (seasonal means ranging from 7,476 - 53,494 kg N-1ha-...

Sodium Chloride Does Not Ensure Microbiological Safety of Foods: Cases and Solutions.

PubMed

Kim, Nam Hee; Cho, Tae Jin; Rhee, Min Suk

2017-01-01

Addition of salt or salt-containing water to food is one of the oldest and most effective preservation methods in history; indeed, salt-cured foods are generally recognized as microbiologically safe due to their high salinity. However, a number of microbiological risks remain. The microbiological hazards and risks associated with salt-cured foods must be addressed more in-depth as they are likely to be underestimated by previous studies. This review examined a number of scientific reports and articles about the microbiological safety of salt-cured foods, which included salted, brined, pickled, and/or marinated vegetables, meat, and seafood. The following subjects are covered in order: (1) clinical cases and outbreaks attributed to salt-cured foods; (2) the prevalence of foodborne pathogens in such foods; (3) the molecular, physiological, and virulent responses of the pathogens to the presence of NaCl in both laboratory media and food matrices; (4) the survival and fate of microorganisms in salt-cured foods (in the presence/absence of additional processes); and (5) the interaction between NaCl and other stressors in food processes (e.g., acidification, antimicrobials, drying, and heating). The review provides a comprehensive overview of potentially hazardous pathogens associated with salt-cured foods and suggests further research into effective intervention techniques that will reduce their levels in the food chain. Copyright © 2017 Elsevier Inc. All rights reserved.

Longitudinal Change of Perceived Salt Intake and Stroke Risk in a Chinese Population.

PubMed

Li, Yun; Huang, Zhe; Jin, Cheng; Xing, Aijun; Liu, Yesong; Huangfu, Chunmei; Lichtenstein, Alice H; Tucker, Katherine L; Wu, Shouling; Gao, Xiang

2018-06-01

Data for a relationship between salt intake and stroke have been inconsistent. This inconstancy could be because of the majority of studies evaluated salt intake at a single time point, which may be insufficient to accurately characterize salt intake throughout the observation period. Included were 77 605 participants from the Kailuan study. We assessed perceived salt intake via questionnaire in 2006, 2008, and 2010. Salt intake trajectories from 2006 to 2010 were identified using latent mixture models. Incident stroke cases were identified from 2010 to 2015 and confirmed by review of medical records. Cox proportional hazards model was used to examine the association between salt intake trajectories and stroke risk after adjusting for possible confounders, including age, sex, lifestyle, social economic status, body mass index, use of medicines, blood pressure, and lipoprotein profiles. Identified were 5 distinct salt intake trajectories: moderate-stable (n=59 241), moderate-decreasing (n=9268), moderate-increasing (n=2975), low-increasing (n=2879), and high-decreasing (n=3242). During the 5-year follow-up period, there were 1564 incident strokes cases. Compared with individuals with the moderate-stable salt intake trajectory, individuals with moderate-decreasing salt intake trajectory had significantly lower cerebral infarction stroke risk (adjusted hazard ratio, 0.76; 95% confidence interval, 0.63-0.92) but not intracerebral hemorrhage risk (adjusted hazard ratio, 0.84; 95% confidence interval, 0.55-1.29). Further adjustment for 2006 or 2010 perceived salt intakes generated similar results. When baseline perceived salt intake only was used as the exposure, a significant dose-response relationship between higher perceived salt intake and higher stroke risk was observed ( P trend=0.006). Change in salt intake was associated with the stroke risk. These data support the dietary recommendation to the reduction of salt intake. © 2018 American Heart Association, Inc.

Salt Content in Ready-to-Eat Food and Bottled Spring and Mineral Water Retailed in Novi Sad.

PubMed

Paplović, Ljiljana B Trajković; Popović, Milka B; Bijelović, Sanja V; Velicki, Radmila S; Torović, Ljilja D

2015-01-01

Salt intake above 5 g/person/day is a strong independent risk factor for hypertension, stroke and cardiovascular diseases. Published studies indicate that the main source of salt in human diet is processed ready-to-eat food, contributing with 65-85% to daily salt intake. The aim of this paper was to present data on salt content of ready-to-eat food retailed in Novi Sad, Serbia, and contribution of the salt contained in 100 g of food to the recommended daily intake of salt for healthy and persons with cardiovascular disease (CVD) risk. In 1,069 samples of ready-to-eat food, salt (sodium chloride) content was calculated based on chloride ion determined by titrimetric method, while in 54 samples of bottled water sodium content was determined using flame-photometry. Food items in each food group were categorized as low, medium or high salt. Average salt content of each food group was expressed as a percentage of recommended daily intake for healthy and for persons with CVD risk. Average salt content (g/100 g) ranged from 0.36 ± 0.48 (breakfast cereals) to 2.32 ± 1.02 (grilled meat). The vast majority of the samples of sandwiches (91.7%), pizza (80.7%), salami (73.9%), sausages (72.9%), grilled meat (70.0%) and hard cheese (69.6%) had a high salt profile. Average amount of salt contained in 100 g of food participated with levels ranging from 7.2% (breakfast cereals) to 46.4% (grilled meat) and from 9.6% to 61.8% in the recommended daily intake for healthy adult and person with CVD risk, respectively. Average sodium content in 100 ml of bottled spring and mineral water was 0.33 ± 0.30 mg and 33 ± 44 mg, respectively. Ready-to-eat food retailed in Novi Sad has high hidden salt content, which could be considered as an important contributor to relatively high salt consumption of its inhabitants.

Micromechanical processes in consolidated granular salt

DOE PAGES

Mills, Melissa Marie; Stormont, John C.; Bauer, Stephen J.

2018-03-27

Here, granular salt is likely to be used as backfill material and a seal system component within geologic salt formations serving as a repository for long-term isolation of nuclear waste. Pressure from closure of the surrounding salt formation will promote consolidation of granular salt, eventually resulting in properties comparable to native salt. Understanding dependence of consolidation processes on stress state, moisture availability, temperature, and time is important for demonstrating sealing functions and long-term repository performance. This study characterizes laboratory-consolidated granular salt by means of microstructural observations. Granular salt material from mining operations was obtained from the bedded Salado Formation hostingmore » the Waste Isolation Pilot Plant and the Avery Island salt dome. Laboratory test conditions included hydrostatic consolidation of jacketed granular salt with varying conditions of confining isochoric stress to 38 MPa, temperature to 250 °C, moisture additions of 1% by weight, time duration, and vented and non-vented states. Resultant porosities ranged between 1% and 22%. Optical and scanning electron microscopic techniques were used to ascertain consolidation mechanisms. From these investigations, samples with 1% added moisture or unvented during consolidation, exhibit clear pressure solution processes with tightly cohered grain boundaries and occluded fluid pores. Samples with only natural moisture content consolidated by a combination of brittle, cataclastic, and crystal plastic deformation. Recrystallization at 250 °C irrespective of moisture conditions was also observed. The range and variability of conditions applied in this study, combined with the techniques used to display microstructural features, are unique, and provide insight into an important area of governing deformation mechanism(s) occurring within salt repository applications.« less

Micromechanical processes in consolidated granular salt

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mills, Melissa Marie; Stormont, John C.; Bauer, Stephen J.

Here, granular salt is likely to be used as backfill material and a seal system component within geologic salt formations serving as a repository for long-term isolation of nuclear waste. Pressure from closure of the surrounding salt formation will promote consolidation of granular salt, eventually resulting in properties comparable to native salt. Understanding dependence of consolidation processes on stress state, moisture availability, temperature, and time is important for demonstrating sealing functions and long-term repository performance. This study characterizes laboratory-consolidated granular salt by means of microstructural observations. Granular salt material from mining operations was obtained from the bedded Salado Formation hostingmore » the Waste Isolation Pilot Plant and the Avery Island salt dome. Laboratory test conditions included hydrostatic consolidation of jacketed granular salt with varying conditions of confining isochoric stress to 38 MPa, temperature to 250 °C, moisture additions of 1% by weight, time duration, and vented and non-vented states. Resultant porosities ranged between 1% and 22%. Optical and scanning electron microscopic techniques were used to ascertain consolidation mechanisms. From these investigations, samples with 1% added moisture or unvented during consolidation, exhibit clear pressure solution processes with tightly cohered grain boundaries and occluded fluid pores. Samples with only natural moisture content consolidated by a combination of brittle, cataclastic, and crystal plastic deformation. Recrystallization at 250 °C irrespective of moisture conditions was also observed. The range and variability of conditions applied in this study, combined with the techniques used to display microstructural features, are unique, and provide insight into an important area of governing deformation mechanism(s) occurring within salt repository applications.« less

Synthesis of chalcogenide and pnictide crystals in salt melts using a steady-state temperature gradient

NASA Astrophysics Data System (ADS)

Chareev, D. A.; Volkova, O. S.; Geringer, N. V.; Koshelev, A. V.; Nekrasov, A. N.; Osadchii, V. O.; Osadchii, E. G.; Filimonova, O. N.

2016-07-01

Some examples of growing crystals of metals, alloys, chalcogenides, and pnictides in melts of halides of alkali metals and aluminum at a steady-state temperature gradient are described. Transport media are chosen to be salt melts of eutectic composition with the participation of LiCl, NaCl, KCl, RbCl, CsCl, AlCl3, AlBr3, KBr, and KI in a temperature range of 850-150°C. Some crystals have been synthesized only using a conducting contour. This technique of crystal growth is similar to the electrochemical method. In some cases, to exclude mutual influence, some elements have been isolated and forced to migrate to the crystal growth region through independent channels. As a result, crystals of desired quality have been obtained using no special equipment and with sizes sufficient for study under laboratory conditions.

Effects of Trace Metals on the Production of Aflatoxins by Aspergillus parasiticus

PubMed Central

Marsh, Paul B.; Simpson, Marion E.; Trucksess, Mary W.

1975-01-01

Certain metals added as salts to a defined basal culture medium influenced the level of aflatoxin production by Aspergillus parasiticus in the low microgramsper-milliliter range of the added metal. In many cases no change or a relatively small change in mat weight and final pH of the medium accompanied this effect. With zinc at added levels of 0 to 10 μg/ml in the medium, aflatoxin increased 30-to 1,000-fold with increasing of zinc, whereas mat weight increased less than threefold. At 25 μg of added zinc per ml, aflatoxin decreased, but mat weight did not. At an added level of 25 μg or less of the metal per ml, salts of iron, manganese, copper, cadmium, trivalent chromium, silver, and mercury partly or completely inhibited aflatoxin production, without influencing mat weight. PMID:238471

Salt Tolerance and Polyphyly in the Cyanobacterium Chroococcidiopsis (Pleurocapsales)1

NASA Technical Reports Server (NTRS)

Cumbers, John Robert; Rothschild, Lynn J.

2014-01-01

Chroococcidiopsis Geitler (Geitler 1933) is a genus of cyanobacteria containing desiccation and radiation resistant species. Members of the genus live in habitats ranging from hot and cold deserts to fresh and saltwater environments. Morphology and cell division pattern have historically been used to define the genus. To better understand the genetic and phenotypic diversity of the genus, 15 species were selected that had been previously isolated from different locations, including salt and freshwater environments. Four markers were sequenced from these 15 species, the 16S rRNA, rbcL, desC1 and gltX genes. Phylogenetic trees were generated which identified two distinct clades, a salt-tolerant clade and a freshwater clade. This study demonstrates that the genus is polyphyletic based on saltwater and freshwater phenotypes. To understand the resistance to salt in more details, species were grown on a range of sea salt concentrations which demonstrated that the freshwater species were salt-intolerant whilst the saltwater species required salt for growth. This study shows an increased resolution of the phylogeny of Chroococcidiopsis and provides further evidence that the genus is polyphyletic and should be reclassified to improve clarity in the literature.

The effect of hydrocarbons on the microstructural evolution in rock salt: a case study on hydrocarbon bearing Ara salt from the South Oman Salt Basin

NASA Astrophysics Data System (ADS)

Schmatz, Joyce; Urai, Janos L.; Wübbeler, Franziska M. M.; Sadler, Marc

2014-05-01

It has been shown that dilatant deformation promotes the incorporation of hydrocarbons into typically low permeable rock salt (Schoenherr et al., 2007). However, there is not much knowledge on subsequent mechanisms related to recrystallization processes, which cause morphological and chemical changes of the carbonic inclusions. This work aims to contribute to an increased understanding of fluid inclusion dynamics related to grain boundary migration recrystallization and hence to facilitate the interpretation of complex microstructures in recrystallized, multiphase salt rocks. In this case study we investigate hydrocarbon-impregnated salt from the Cambrian Ara Group in the South Oman Salt Basin. The samples were cored from cm-m thick anhydrite-salt sequences overlying hydrocarbon bearing carbonate stringers in 3300 m depth. The anhydrite layers consist mainly of fine-grained anhydrite, which contains calcite, dolomite, and olivine inclusions. Solid bitumen and lighter hydrocarbon phases are observed in between the anhydrite grains and along cracks. Anhydrite layers host salt veins, which contain fragments of anhydrite. These fragments do not differ in composition or structure from the host material and the related vein microstructures indicate crack-seal mechanisms. Halite in the salt layers is almost entirely recrystallized with solid inclusions consisting of anhydrite, calcite, dolomite and olivine with hydrocarbon-coatings present inside grains and along grain boundaries. Solid inclusions cause pinning indicated by a decreased recrystallized grain size and by the presence of grains with preserved substructures representing earlier deformation phases. We observe two types of carbonic inclusions: I) solid bitumen coatings along grain boundaries and microcracks, interpreted to be incorporated into the salt in an overpressure state that allowed dilatancy of the salt, and II) less degraded, liquid hydrocarbons along grain boundaries in the vicinity of the anhydrite, interpreted to be incorporated into the salt in a subsequent deformation phase. Type II inclusions usually form arrays of isolated inclusions (liquid hydrocarbons, vapor, and aqueous phases in minor proportions) along grain boundaries of the recrystallized grains, presumably formed in a surface-energy controlled shrinking process from thin fluid films. Here, the contact with mobile grain boundaries promoted necking down and decomposition of multiphase inclusions. We present a model, which describes the dynamic behavior of liquid hydrocarbons in mobile grain boundaries after their enclosure into the salt layers. The model is based on numerous microanalytical methods, such as optical microscopy, fluorescence microscopy, cryo-SEM, and EDX. Schoenherr, J., et al. (2007), Limits to the sealing capacity of rock salt: A case study of the infra-Cambrian Ara Salt from the South Oman salt basin, AAPG Bulletin, 91(11), 1541-1557

Neutronic experiments with fluorine rich compounds at LR-0 reactor

DOE PAGES

Losa, Evzen; Kostal, Michal; Czakoj, T.; ...

2018-06-06

Here, research on molten salt reactor (MSR) neutronics continues in Research Centre Rez (Czech Republic) with experimental work being conducted using fluoride salt that was originally used in the Molten Salt Reactor Experiment (MSRE). Previous results identified significant variations in the neutron spectrum measured in LiF-NaF salt. These variations could originate from the fluorine description in current nuclear data sets. Subsequent experiments were performed to try to confirm this phenomenon. Therefore, another fluorine-rich compound, Teflon, was used for testing. Critical experiments showed slight discrepancies in C/E-1 for both compounds, Teflon and FLIBE, and systematic overestimation of criticality was observed inmore » calculations. Different nuclear data libraries were used for data set testing. For Teflon, the overestimation is higher when using JENDL-3.3, JENDL-4, and RUSFOND-2010 libraries, all three of which share the same inelastic-to-elastic scattering cross section ratio. Calculations using other libraries (ENDF/B-VII.1, ENDF/B-VII.0, JEFF-3.2, JEFF-3.1, and CENDL-3.1) tend to be closer to the experimental value. Neutron spectrum measurement in both substances revealed structure similar to that seen in previous measurements using LiF-NaF salt, which indicates that the neutron spectrum seems to be strongly shaped by fluorine. Discrepancies between experimental and calculational results seem to be larger in the neutron energy range of 100–1300 keV than in higher energies. In the case of neutron spectrum calculation, none of the tested libraries gives overall better results than the others.« less

Neutronic experiments with fluorine rich compounds at LR-0 reactor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Losa, Evzen; Kostal, Michal; Czakoj, T.

Here, research on molten salt reactor (MSR) neutronics continues in Research Centre Rez (Czech Republic) with experimental work being conducted using fluoride salt that was originally used in the Molten Salt Reactor Experiment (MSRE). Previous results identified significant variations in the neutron spectrum measured in LiF-NaF salt. These variations could originate from the fluorine description in current nuclear data sets. Subsequent experiments were performed to try to confirm this phenomenon. Therefore, another fluorine-rich compound, Teflon, was used for testing. Critical experiments showed slight discrepancies in C/E-1 for both compounds, Teflon and FLIBE, and systematic overestimation of criticality was observed inmore » calculations. Different nuclear data libraries were used for data set testing. For Teflon, the overestimation is higher when using JENDL-3.3, JENDL-4, and RUSFOND-2010 libraries, all three of which share the same inelastic-to-elastic scattering cross section ratio. Calculations using other libraries (ENDF/B-VII.1, ENDF/B-VII.0, JEFF-3.2, JEFF-3.1, and CENDL-3.1) tend to be closer to the experimental value. Neutron spectrum measurement in both substances revealed structure similar to that seen in previous measurements using LiF-NaF salt, which indicates that the neutron spectrum seems to be strongly shaped by fluorine. Discrepancies between experimental and calculational results seem to be larger in the neutron energy range of 100–1300 keV than in higher energies. In the case of neutron spectrum calculation, none of the tested libraries gives overall better results than the others.« less

The rate of rise, fall and gravity spreading at Siahou diapir (Southern Iran)

NASA Astrophysics Data System (ADS)

Aftabi, P.; Roustaie, M.

2009-04-01

InSAR imaging can be used for extracting three dimensional information of the diapirs surface by using the phase part of the radar signal. We used InSAR to examine the cumulative surface deformation between 920706 to 060518, in a 10×10 km region surrounding the salt diapir at Kuh-e-Namak Siahou. The interferograms span periods was between 35-70 and 1248 days. Images acquired in 12 increments provided by ESA. This technique used here involves computation and subsequent combinations of interferometric phase gradient maps were used for mapping the salt flow deformation in the Zagros. Kuh-e-Namak Siahou is one of the salt extrusions currently active in the Zagros range in Iran. Salt rises from a mother salt horizon about 4 km deep and extruded as a dome with glacier on the surface. The geometry and inferred flow pattern of the salt changed between the increments, emphasizing that the extrusion rate and gravity spreading is not steady. Elevations in the salt mountain range from 1000 to 1640 meters and the displacements exceed to 20cm per year . Our InSAR study(Fig1) suggest that the dimensions and velocity of the salt movements are changing between 2 to 20mm per year(-0.7 to0.59 mm per day).The rate of surface dissolution changed between 2 to 4 cm a-1, and its rate of rise out of its orifice at 0 to 200 mm per year. The InSAR study suggest that the vigorous salt extrusion in Siahou is probably active.The deep source probably rise at a similar rates in the past but it fall in the time of InSAR study. The rate of fall was 260 mm per year(for 14 years). The InSAR images suggest that salt extrusion in Siahou flow laterally at rate 20-25 mm per year and the namakiers felt at -2 mm per month. The InSAR results indicated concentric and radial flow in the diapir from a central point at summit and spreading glaciers in sideways.Phase differences measured in our interferograms generally in the range of 0-260 mm/yr(-260 mm) within the studied period, with exceptional high rates that exceed 50 mm/yr in diapir Siahou. Comparison of our InSAR observations with models suggest a similarity in the strain pattern in the model and prototype. Our observations also show that in certain locations of Zagros, movements appear to be structurally controlled by salt flow, and diapirism. This report will improve our understanding on how the salt diapirs work and our capability to predict future flow and the associated hazards for storages in salt and provides the first direct, spatially resolved, measurement of ongoing flow of salt. Key words: Salt tectonics,InSAR,Monitoring,Iran,Zagros,Salt diapir,salt kinematics, Zagros fold-thrust belt, Hormuz salt, analogue modelling,salt extrusion, crustal shortening

Platinum salt sensitivity in refinery workers: incidence and effects of smoking and exposure.

PubMed Central

Calverley, A E; Rees, D; Dowdeswell, R J; Linnett, P J; Kielkowski, D

1995-01-01

OBJECTIVE--To measure the incidence of platinum salt sensitivity (PSS) in refinery workers and examine the influence of cigarette smoking and exposure to platinum salts on sensitisation. DESIGN--A prospective cohort study with examination of workers at quarterly intervals for 18 months, and again at 24 months. SETTING--A South African primary platinum refinery. SUBJECTS--78 new recruits, selected by the refinery's usual procedure, without apparent atopy and in good respiratory health. RESULTS--After 24 months 32 (41%) subjects had been diagnosed PSS and were subsequently medically separated. Twenty two (28%) cases were confirmed by positive skin prick test to platinum salts, 10 (13%) cases were symptomatic but skin prick negative. Incidence of cases per 100 person-months was 1.9 skin prick positive and 0.8 negative. Risk of sensitisation was about eight times greater for smokers than non-smokers, and six times greater for high exposure than low exposure. CONCLUSION--Smoking and intensity of exposure were definitely associated with development of PSS. Positive responses to platinum salt skin prick test had a 100% positive predictive value for symptoms and signs of PSS if exposure continued. PMID:7489056

Scope and limitations of the Heck-Matsuda-coupling of phenol diazonium salts and styrenes: a protecting-group economic synthesis of phenolic stilbenes.

PubMed

Schmidt, Bernd; Elizarov, Nelli; Berger, René; Hölter, Frank

2013-06-14

4-Phenol diazonium salts undergo Pd-catalyzed Heck reactions with various styrenes to 4'-hydroxy stilbenes. In almost all cases higher yields and fewer side products were observed, compared to the analogous 4-methoxy benzene diazonium salts. In contrast, the reaction fails completely with 2- and 3-phenol diazonium salts. For these substitution patterns the methoxy-substituted derivatives are superior.

Polymorphisms of three genes (ACE, AGT and CYP11B2) in the renin-angiotensin-aldosterone system are not associated with blood pressure salt sensitivity: A systematic meta-analysis.

PubMed

Sun, Jiahong; Zhao, Min; Miao, Song; Xi, Bo

2016-01-01

Many studies have suggested that polymorphisms of three key genes (ACE, AGT and CYP11B2) in the renin-angiotensin-aldosterone system (RAAS) play important roles in the development of blood pressure (BP) salt sensitivity, but they have revealed inconsistent results. Thus, we performed a meta-analysis to clarify the association. PubMed and Embase databases were searched for eligible published articles. Fixed- or random-effect models were used to pool odds ratios and 95% confidence intervals based on whether there was significant heterogeneity between studies. In total, seven studies [237 salt-sensitive (SS) cases and 251 salt-resistant (SR) controls] for ACE gene I/D polymorphism, three studies (130 SS cases and 221 SR controls) for AGT gene M235T polymorphism and three studies (113 SS cases and 218 SR controls) for CYP11B2 gene C344T polymorphism were included in this meta-analysis. The results showed that there was no significant association between polymorphisms of these three polymorphisms in the RAAS and BP salt sensitivity under three genetic models (all p > 0.05). The meta-analysis suggested that three polymorphisms (ACE gene I/D, AGT gene M235T, CYP11B2 gene C344T) in the RAAS have no significant effect on BP salt sensitivity.

Protein interactions in concentrated ribonuclease solutions

NASA Astrophysics Data System (ADS)

Boyer, Mireille; Roy, Marie-Odile; Jullien, Magali; Bonneté, Françoise; Tardieu, Annette

1999-01-01

To investigate the protein interactions involved in the crystallization process of ribonuclease A, dynamic light scattering (DLS) and small angle X-ray scattering experiments (SAXS) were performed on concentrated solutions. Whereas the translational diffusion coefficient obtained from DLS is sensitive to thermodynamic and hydrodynamic interactions and permits to calculate an interaction parameter, the shape of the SAXS curves is related to the type of interaction (attractive or repulsive). We compared the effect of pH on protein interactions in the case of two types of crystallizing agents: a mixture of salts (3 M sodium chloride plus 0.2 M ammonium sulfate) and an organic solvent (ethanol). The results show that in the presence of ethanol, as in low salt, protein interactions become more attractive as the pH increases from 4 to 8 and approaches the isoelectric point. In contrast, a reverse effect is observed in high salt conditions: the strength of attractive interactions decreases as the pH increases. The range of the pH effect can be related to ionization of histidine residues, particularly those located in the active site of the protein. The present observations point out the important role played by localized charges in crystallization conditions, whatever the precipitating agent.

Induced amphotropic and thermotropic ionic liquid crystallinity in phosphonium halides: "lubrication" by hydroxyl groups.

PubMed

Ma, Kefeng; Somashekhar, B S; Gowda, G A Nagana; Khetrapal, C L; Weiss, Richard G

2008-03-18

The influence of covalently attaching hydroxymethylene to the methyl groups of methyl-tri-n-alkylphosphonium halides (where the alkyl chains are decyl, tetradecyl, or octadecyl and the halide is chloride or bromide) or adding methanol as a solute to the salts on their solid, liquid-crystalline (smectic A2), and isotropic phases has been investigated using a variety of experimental techniques. These structural and compositional changes are found to induce liquid crystallinity in some cases and to enhance the temperature range and lower the onset temperature of the liquid-crystalline phases in some others. The results are interpreted in terms of the lengths of the three n-alkyl chains attached to the phosphorus cation, the nature of the halide anion, the influence of H-bonding interactions at the head group regions of the layered phases, and other solvent-solute interactions. The fact that at least 1 molar equiv of methanol must be added to effect complete (isothermal) conversion of a solid methyl-tri-n-alkylphosphonium salt to a liquid crystal demonstrates a direct and strong association between individual methanol molecules and the phosphonium salts. Possible applications of such systems are suggested.

Foods and risk of bladder cancer: a case-control study in Uruguay.

PubMed

Balbi, J C; Larrinaga, M T; De Stefani, E; Mendilaharsu, M; Ronco, A L; Boffetta, P; Brennan, P

2001-10-01

A case-control study on 144 cases of transitional cell bladder carcinoma and 576 hospitalized controls was conducted in Montevideo, Uruguay. Barbecued meat, salted meat and fried eggs were associated with significant increased risks of bladder cancer (odds ratio (OR) for high intake of salted meat 4.04, 95% confidence interval (CI) 2.24-7.27). On the other hand, all fruits, cooked vegetables, potatoes and cheese were associated with inverse associations (OR for high consumption of potatoes 0.38, 95% CI 0.23-0.64). The associations with salted and barbecued meat suggest that the way of preserving or cooking meat play a role in bladder carcinogenesis. More precisely, N-nitroso compounds and heterocyclic amines could be involved in this process.

Dissolution and subsequent re-crystallization as zeroing mechanism, thermal properties and component resolved dose response of salt (NaCl) for retrospective dosimetry.

PubMed

Polymeris, George S; Kitis, George; Kiyak, Nafiye G; Sfamba, Ioanna; Subedi, Bhagawan; Pagonis, Vasilis

2011-09-01

In the present study we report dosimetric properties of iodized salt aiming at using it as an accidental luminescent dosimeter. It was found that the very good sensitivity of its main dosimetric peak is strongly affected by thermal treatments. This is also the case for OSL emission. The sensitivity loss due to heating implies that caution should be exercised while applying single aliquot protocols for dose evaluation. The sequence of dissolution and subsequent re-crystallization was established to be an extremely effective zeroing mechanism for the TL signal. The linearity in the dose response was also monitored in the case of dissolved and subsequently re-crystallized salt. In the case of naturally occurring salt, zeroing of the TL signal due to dissolution as well as the linearity of dose response up to doses as large as 100 Gy were found to be very promising features for dating applications. Copyright © 2011 Elsevier Ltd. All rights reserved.

Precipitation of sparingly soluble salts in packed sandbeds

NASA Astrophysics Data System (ADS)

Pavlakou, Efstathia I.; Sygouni, Varvara; Paraskeva, Christakis A.

2015-04-01

One of the main problems encountered by the oil extraction industry, is the reduction of the local permeability of the rock formation near the extraction wells because of salt deposition in the pores of the rocks during the injection of brine water to displace the trapped oil ganglia within the oil formations. This phenomenon makes the oil recovery less efficient and under extreme cases the well is abandoned with a large amount of oil entrapped. Several detailed studies have been conducted in the past concerning sand bed consolidation using sparingly soluble salts for varying conditions (e.g. temperature, grain size, sand type, salt concentrations etc) and various salts [1]. Nevertheless, salt precipitation in the rock formation pores under the presence of other miscible or immiscible substances with water has not been investigated in details yet. In the present study, salt (CaCO3) precipitation experiments were performed in small beds packed with sea sand mixed with a low amount of CaCO3 seed grains. The experiments were performed using pure solutions (NaHCO3, CaCl2.2H2O) and solutions mixed with Ethylene Glycol in sand beds. Additionally, precipitation experiments were performed using pure solutions in sand beds saturated with oil phase (n-dodecane) for a wide range of solution supersaturation. During the experiments the ionic strength was kept constant. pH and concentration values of calcium ion of the effluent were measured and the precipitated salt crystals were identified using X-ray Diffraction (XRD) method. At the end of each experiment Scanning Electron Microscope (SEM) was conducted using a sample of the precipitated sand to identify the morphology of the precipitated crystals and their cohesion with sand grains. Acknowledgments This research was partially funded by the European Union (European Social Fund-ESF) and Greek National Funds through the Operational program "Education and Lifelong Learning" under the action Aristeia II (Code No 4420). References [1] Paraskeva C. A., Charalampous P. C., Stokka L. E., Klepetsanis P. G., Koutsoukos P. G., Read P., Ostvold, T. and Payatakes A. C. (2000), ''Sandbed Consolidation with Mineral Precipitation'', Journal of Colloid and Interface Science, 232, 326-339.

Salt Efflorescence Effects on Soil Surface Erodibility and Dust Emissions

NASA Astrophysics Data System (ADS)

Van Pelt, R. S.; Zhang, G.

2017-12-01

Soluble salts resulting from weathering of geological materials often form surface crusts or efflorescences in areas with shallow saline groundwater. In many cases, the affected areas are susceptible to wind erosion due to their lack of protective vegetation and their flat topography. Fugitive dusts containing soluble salts affect the biogeochemistry of deposition regions and may result in respiratory irritation during transport. We created efflorescent crusts on soil trays by surface evaporation of single salt solutions and bombarded the resultant efflorescences with quartz abrader sand in a laboratory wind tunnel. Four replicate trays containing a Torrifluvent soil affected by one of nine salts commonly found in arid and semiarid streams were tested and the emissions were captured by an aspirated multi-stage deposition and filtering system. We found that in most cases the efflorescent crust reduced the soil surface erodibility but also resulted in the emission of salt rich dust. Two of the salts, sodium thiosulfate and calcium chloride, resulted in increased soil volume and erodibility. However, one of the calcium chloride replicates was tested after an outbreak of humid air caused hygroscopic wetting of the soil and it became indurated upon drying greatly decreasing the erodibility. Although saline affected soils are not used for agricultural production and degradation is not a great concern, the release of salt rich dust is an area of environmental concern and steps to control the dust emissions from affected soils should be developed. Future testing will utilize suites of salts found in streams of arid and semiarid regions.

Search for extraterrestrial life using chiral molecules: mandelate racemase as a test case.

PubMed

Thaler, Tracey L; Gibbs, Phillip R; Trebino, Rick P; Bommarius, Andreas S

2006-12-01

We have investigated an enzymatic racemization reaction as a marker for extraterrestrial life, which resulted in a change in optical rotation of a mandelic acid over time, as measured by polarimetry. Mandelate racemase was active in aqueous buffer in a temperature range between 0 degrees C and 70 degrees C and also in concentrated ammonium salt solutions and water-in-oil microemulsions in a temperature range between -30 degrees C and 60-70 degrees C; however, the enzyme was not active in several organic cryosolvents. Thus, we have demonstrated that concentrated ammonium salt solutions and water-in-oil microemulsions, both of which are able to form on extraterrestrial planets and moons in the presence of liquid water, are suitable media for enzyme reactions at subzero temperatures. Kinetic data for the mandelate racemase reaction obtained by polarimetry, while reproducible and internally consistent, differed significantly from several sets of data obtained previously by other methods such as chromatography and hydrogen-deuterium exchange. However, we conclude that reactions yielding a polarimetric signal, such as the racemizations employed in this work, are suitable mechanisms by which to utilize a change in chirality over time as a tool to detect signs of life.

Biochemical solubilization of toxic salts from residual geothermal brines and waste waters

DOEpatents

Premuzic, Eugene T.; Lin, Mow S.

1994-11-22

A method of solubilizing metal salts such as metal sulfides in a geothermal sludge using mutant Thiobacilli selected for their ability to metabolize metal salts at high temperature is disclosed, The method includes the introduction of mutated Thiobacillus ferrooxidans and Thiobacillus thiooxidans to a geothermal sludge or brine. The microorganisms catalyze the solubilization of metal salts, For instance, in the case of metal sulfides, the microorganisms catalyze the solubilization to form soluble metal sulfates.

Molten Salt Thermal Energy Storage Systems

NASA Technical Reports Server (NTRS)

Maru, H. C.; Dullea, J. F.; Kardas, A.; Paul, L.; Marianowski, L. G.; Ong, E.; Sampath, V.; Huang, V. M.; Wolak, J. C.

1978-01-01

The feasibility of storing thermal energy at temperatures of 450 C to 535 C in the form of latent heat of fusion was examined for over 30 inorganic salts and salt mixtures. Alkali carbonate mixtures were chosen as phase-change storage materials in this temperature range because of their relatively high storage capacity and thermal conductivity, moderate cost, low volumetric expansion upon melting, low corrosivity, and good chemical stability. Means of improving heat conduction through the solid salt were explored.

Visible light catalyzed methylsulfoxidation of (het)aryl diazonium salts using DMSO.

PubMed

Pramanik, Mukund M D; Rastogi, Namrata

2016-06-30

The visible light catalyzed methylsulfoxidation of (het)aryl diazonium salts using DMSO is illustrated. This is the first example of DMSO being used as the source of the methylsulfinyl group. The procedure tolerates a wide range of functional groups on (het)aryl diazonium salts and provides aryl methyl sulfoxides in excellent yields under mild reaction conditions.

Surface tensions of inorganic multicomponent aqueous electrolyte solutions and melts.

PubMed

Dutcher, Cari S; Wexler, Anthony S; Clegg, Simon L

2010-11-25

A semiempirical model is presented that predicts surface tensions (σ) of aqueous electrolyte solutions and their mixtures, for concentrations ranging from infinitely dilute solution to molten salt. The model requires, at most, only two temperature-dependent terms to represent surface tensions of either pure aqueous solutions, or aqueous or molten mixtures, over the entire composition range. A relationship was found for the coefficients of the equation σ = c(1) + c(2)T (where T (K) is temperature) for molten salts in terms of ion valency and radius, melting temperature, and salt molar volume. Hypothetical liquid surface tensions can thus be estimated for electrolytes for which there are no data, or which do not exist in molten form. Surface tensions of molten (single) salts, when extrapolated to normal temperatures, were found to be consistent with data for aqueous solutions. This allowed surface tensions of very concentrated, supersaturated, aqueous solutions to be estimated. The model has been applied to the following single electrolytes over the entire concentration range, using data for aqueous solutions over the temperature range 233-523 K, and extrapolated surface tensions of molten salts and pure liquid electrolytes: HCl, HNO(3), H(2)SO(4), NaCl, NaNO(3), Na(2)SO(4), NaHSO(4), Na(2)CO(3), NaHCO(3), NaOH, NH(4)Cl, NH(4)NO(3), (NH(4))(2)SO(4), NH(4)HCO(3), NH(4)OH, KCl, KNO(3), K(2)SO(4), K(2)CO(3), KHCO(3), KOH, CaCl(2), Ca(NO(3))(2), MgCl(2), Mg(NO(3))(2), and MgSO(4). The average absolute percentage error between calculated and experimental surface tensions is 0.80% (for 2389 data points). The model extrapolates smoothly to temperatures as low as 150 K. Also, the model successfully predicts surface tensions of ternary aqueous mixtures; the effect of salt-salt interactions in these calculations was explored.

Hydration patterns and salting effects in sodium chloride solution.

PubMed

Li, Weifeng; Mu, Yuguang

2011-10-07

The salting effects of 2M sodium chloride electrolyte are studied based on a series of model solutes with properties ranging from hydrophobic to hydrophilic. Generally, hydrophobic solutes will be salted out and hydrophilic solutes will be salted in by NaCl solution. The solvation free energy changes are highly correlated with Kirkwood-Buff integrals. The underlying mechanism resorts to the preferential binding of ions and water to solutes. Our results demonstrate that the salting effect not only depends on the salt's position in Hofmeister series, but also on the solutes' specifics. Taking the hydration free energies of solutes and ions as independent variables, a schematic diagram of salting effects is suggested. The resolved multifaceted salting effects rely on the sensitive balance of the tripartite interaction among solutes, ions, and water. © 2011 American Institute of Physics

Order of wetting transitions in electrolyte solutions.

PubMed

Ibagon, Ingrid; Bier, Markus; Dietrich, S

2014-05-07

For wetting films in dilute electrolyte solutions close to charged walls we present analytic expressions for their effective interface potentials. The analysis of these expressions renders the conditions under which corresponding wetting transitions can be first- or second-order. Within mean field theory we consider two models, one with short- and one with long-ranged solvent-solvent and solvent-wall interactions. The analytic results reveal in a transparent way that wetting transitions in electrolyte solutions, which occur far away from their critical point (i.e., the bulk correlation length is less than half of the Debye length) are always first-order if the solvent-solvent and solvent-wall interactions are short-ranged. In contrast, wetting transitions close to the bulk critical point of the solvent (i.e., the bulk correlation length is larger than the Debye length) exhibit the same wetting behavior as the pure, i.e., salt-free, solvent. If the salt-free solvent is governed by long-ranged solvent-solvent as well as long-ranged solvent-wall interactions and exhibits critical wetting, adding salt can cause the occurrence of an ion-induced first-order thin-thick transition which precedes the subsequent continuous wetting as for the salt-free solvent.

Salt taste preference, sodium intake and gastric cancer in China.

PubMed

Zhang, Zhiyong; Zhang, Xiefu

2011-01-01

The risk factors mostly strongly associated with gastric cancer are gastric bacteria Helicobacter pylori and diet. By using a case-control study among residents in China, we examined the association between sodium intake, presence of H,pylori, and gastric cancer risk. A population-based case-control study including 235 cases and 410 controls were used. Potential risk factors of gastric cancer were interview for cases and controls by questionnaire, salt taste preference was measured for all subjects, and IgG antibodies to H,pylori was used for H.pylori infection. Risk measures were calculated using unconditional logistic regression. H.pylori infection and smoking increased the risk of gastric cancer, with the OR(95%CI) of 1.91(1.32-2.79) and 1.47(1.05- 2.05), respectively. Dietary sodium intake independently increased the risk of gastric cancer. Participants with the highest sodium intake(>5g/day) had a high gastric cancer risk [OR(95%CI)= 3.78(1.74-5.44)]. Participants with the salt taste preference at 7.3g/L and ≥ 14.6g/L showed higher risk of gastric cancer [OR(95%) for 7.3g/L and ≥ 14.6g/L were 5.36(2.72-10.97) and 4.75(2.43-8.85), respectively]. A significantly interaction was found between salt taste preference and H.pylori infection (p=0.037). Salt taste preference was significantly correlated with sodium intake (Correlation coefficient=0.46, p< 0.001). Salt taste preference test could be a simple way to evaluate an inherited characteristic of sodium intake, and our study confirms the gastric cancer is associated with sodium intake and H.pylori.

Development of media for dynamic latent heat storage for the low-temperature range. Part 1: Thermal analyses of selected salt hydrate systems

NASA Technical Reports Server (NTRS)

Kanwischer, H.; Tamme, R.

1985-01-01

Phase change temperatures and phase change enthalpies of seventeen salt hydrates, three double salts, and four eutectics were measured thermodynamically and the results reported herein. Good results were obtained, especially for congruently melting salt hydrates. Incongruently melting salt hydrates appear less suitable for heat storage applications. The influence of the second phase - water, acid and hydroxide - to the latent heat is described. From these results, basic values of the working temperatures and storage capabilities of various storage media compositions may be derived.

A Systematic Review of Fatalities Related to Acute Ingestion of Salt. A Need for Warning Labels?

PubMed Central

Campbell, Norm R. C.; Train, Emma J.

2017-01-01

There are sporadic cases of fatalities from acutely eating salt. Yet, on social media, there are “challenges to” and examples of children and some adults acutely eating salt, and recently a charity advocated eating small amounts of salt to empathize with Syrian refugees. We performed a systematic review of fatalities from ingesting salt to assess if relatively moderate doses of salt could be fatal. In 27 reports, there were 35 fatalities documented (19 in adults and 16 in children). The lethal dose was estimated to be less than 10 g of sodium (<5 teaspoons of salt) in two children, and less than 25 g sodium in four adults (<4 tablespoons of salt). The frequency of fatal ingestion of salt is not able to be discerned from our review. If investigation of the causes of hypernatremia in hospital records indicates salt overdose is relatively common, consideration could be given to placing warning labels on salt containers and shakers. Such warning labels can have the added advantage of reducing dietary salt consumption. PMID:28644412

Development of high temperature transport technology for LiCl-KCl eutectic salt in pyroprocessing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, Sung Ho; Lee, Hansoo; Kim, In Tae

The development of high-temperature transport technologies for molten salt is a prerequisite and a key issue in the industrialization of pyro-reprocessing for advanced fuel cycle scenarios. The solution of a molten salt centrifugal pump was discarded because of the high corrosion power of a high temperature molten salt, so the suction pump solution was selected. An apparatus for salt transport experiments by suction was designed and tested using LiC-KCl eutectic salt. The experimental results of lab-scale molten salt transport by suction showed a 99.5% transport rate (ratio of transported salt to total salt) under a vacuum range of 100 mtorrmore » - 10 torr at 500 Celsius degrees. The suction system has been integrated to the PRIDE (pyroprocessing integrated inactive demonstration) facility that is a demonstrator using non-irradiated materials (natural uranium and surrogate materials). The performance of the suction pump for the transport of molten salts has been confirmed.« less

Biochemical solubilization of toxic salts from residual geothermal brines and waste waters

DOEpatents

Premuzic, E.T.; Lin, M.S.

1994-11-22

A method of solubilizing metal salts such as metal sulfides in a geothermal sludge using mutant Thiobacilli selected for their ability to metabolize metal salts at high temperature is disclosed. The method includes the introduction of mutated Thiobacillus ferrooxidans and Thiobacillus thiooxidans to a geothermal sludge or brine. The microorganisms catalyze the solubilization of metal salts. For instance, in the case of metal sulfides, the microorganisms catalyze the solubilization to form soluble metal sulfates. 54 figs.

The Intermediate Range Nuclear Forces (INF) Negotiations and Treaty: An Historical Case Study.

DTIC Science & Technology

1989-09-01

Level Lobbying for SALT," Time, 114: 37-36 (22 October 1979). 38. Hoyle , Russ. "Andropov’s Ultimatum," Time, 122: 70- 71 (7 November 1983). 39. Hoyle ...Russ. "Concession or Propaganda?," Time, 121: 28-29 (16 May 1983). 40. Hoyle , Russ. "Listening to the Allies," Time, 121: 26 (7 February 1983). 41...Disarmament and Global Security: A Search For Alternatives. Boulder CO: Westview Press, Inc., 1984. 44. Kaplan, Fred M. "Dubious Specter: A Skeptical Look at

Effect of basement structure and salt tectonics on deformation styles along strike: An example from the Kuqa fold-thrust belt, West China

NASA Astrophysics Data System (ADS)

Neng, Yuan; Xie, Huiwen; Yin, Hongwei; Li, Yong; Wang, Wei

2018-04-01

The Kuqa fold-thrust belt (KFTB) has a complex thrust-system geometry and comprises basement-involved thrusts, décollement thrusts, triangle zones, strike-slip faults, transpressional faults, and pop-up structures. These structures, combined with the effects of Paleogene salt tectonics and Paleozoic basement uplift form a complex structural zone trending E-W. Interpretation and comprehensive analysis of recent high-quality seismic data, field observations, boreholes, and gravity data covering the KFTB has been performed to understand the characteristics and mechanisms of the deformation styles along strike. Regional sections, fold-thrust system maps of the surface and the sub-salt layer, salt and basement structure distribution maps have been created, and a comprehensive analysis of thrust systems performed. The results indicate that the thrust-fold system in Paleogene salt range can be divided into five segments from east to west: the Kela-3, Keshen, Dabei, Bozi, and Awate segments. In the easternmost and westernmost parts of the Paleogene salt range, strike-slip faulting and basement-involved thrusting are the dominant deformation styles, as basement uplift and the limits of the Cenozoic evaporite deposit are the main controls on deformation. Salt-core detachment fold-thrust systems coincide with areas of salt tectonics, and pop-up, imbricate, and duplex structures are associated with the main thrust faults in the sub-salt layer. Distribution maps of thrust systems, basement structures, and salt tectonics show that Paleozoic basement uplift controlled the Paleozoic foreland basin morphology and the distribution of Cenozoic salt in the KFTB, and thus had a strong influence on the segmented structural deformation and evolution of the fold-thrust belt. Three types of transfer zone are identified, based on the characteristics of the salt layer and basement uplift, and the effects of these zones on the fault systems are evaluated. Basement uplift and the boundary of the salt deposit generated strike-slip faults in the sub-salt layer and supra-salt layers at the basin boundary (Model A). When changes in the basement occurred within the salt basin, strike-slip faults controlled the deformation styles in the sub-salt layer and shear-zone dominated in the supra-salt layer (Model B). A homogeneous basement and discontinues salt layer formed different accommodation zones in the sub- and supra-salt layers (Model C). In the sub-salt layer the thrusts form imbricate structures on the basal décollement, whereas the supra-salt layer shows overlapping, discontinuous faults and folds with kinds of salt tectonics, and has greater structural variation than the sub-salt layer.

Effective conservative treatment of umbilical pilonidal sinus disease: Silver nitrate? Salt?

PubMed

Sözen, Selim; Kanat, Burhan Hakan; Kanat, Zekiye; Bali, Ilhan; Polat, Yilmaz

2015-01-01

The aim of this study was to compare the three different treatment methods and investigate The effectiveness of the therapeutic effect of common salt. This retrospective study involved patients who were treated in our clinic for umbilical pilonidal sinus disease between January 2010 and December 2011. The patients were divided to three subgroups according to treatment methods. Group I: Cases treated with only local debridement and systemic antibiotic, group II: cases treated with local debridement, systemic antibiotic and silver nitrate, group 3: cases treated with debridement, systemic antibiotic and salt. In this study, 63 patients with the diagnosis of UPS were treated in our clinic. The patients were classified into three groups; group I included 20 patients, group II included 18 patients and group III included 18 patients. During 16-24 months of follow-up, 4 (20%) recurrences in group1 and 2 (11.1%) recurrences in group 2 were detected. Recurrence rate of group 3 was significantly different (5.55%) when compared to group 2. The mean period for returning to daily activities and work was 1 day for the patients. In conclusion, we suggest that pilonidal sinus cases which are not complicated by abcess and cellulitis can be treated by local removal of umbilical hairs, debridement and dressing without surgery. We conclude that application of common salt (table/ cooking salt) to umbilical pilonidal sinus with granuloma is a simple and highly effective way of treatment without any relapse and complications. Conservative treatment, Local debridement, Umblical pilonidal sinus.

Intrinsically Disordered Titin PEVK as a Molecular Velcro: Salt-Bridge Dynamics and Elasticity

NASA Astrophysics Data System (ADS)

Forbes, Jeffrey; Tsai, Wanxia; Wittebort, Richard; Wang, Kuan

2009-03-01

Titin is a giant modular protein (3-4 MDa) found in the muscle sarcomere, where the intrinsically disordered and elastic PEVK segment plays a major role in the passive tension of skeletal and heart tissues. We have proposed that salt-bridges play a central role in the elasticity of PEVK. The 50 kDa engineered PEVK polyprotein shows well-resolved NMR spectra at all concentrations. From long-range NOE's, we observed stable K to E salt-bridges. Simulated annealing with NMR restraints yielded a manifold of structures for an exon 172 trimer. Steered molecular dynamics simulations were done to study how the manifold of salt-bridges evolves during the stretching experiment. Repeated SMD simulations at slow velocity (0.0005 nm/ps) showed force spectra consistent with experimental AFM force spectra of the polyprotein. SMD shows that salt-bridges occur even at high degrees of stretch and that these short range interactions are in integral part of the mechanical properties of PEVK. We propose that the long-range, non-stereospecific nature of electrostatic interactions provide a facile mechanism to tether and untether the flexible chains, which in turn affect elasticity as well as control the accessibility of protein-protein interaction to these nanogel-like proteins.

Mechanism of concave ``tafoni'' and convex ``domal shape'' formation on TRIASSIC red sandstone of some old buildings, Chester City, UK, Case study

NASA Astrophysics Data System (ADS)

Kamh, G. M. E.

2005-08-01

The weathering factors act on the recent and archaeological sites through different processes based on the dominant environmental conditions. The net result of weathering is deformation of the original form of construction rock. In the current case study, the main aim is to find out the mechanism of formation of two different weathering forms recorded on many old buildings taking Chester City as a case study. The construction rock in the case study is arenitic sandstone with carbonate content ranging from 0.0 to 15.6%. The sandstone blocks are cemented together by hydraulic lime mortar that can easily be altered chemically to salts by acid rain that dominates at the study area. In case of mortar with worse geotechnical limits than the sandstone blocks, the net result is convex “domal” shape blocks, but in case of mortar with better geotechnical limits than the construction sandstone, the net result of weathering is tafoni “concave” weathering form.

Consumption of sodium and salted foods in relation to cancer and cardiovascular disease: the Japan Public Health Center-based Prospective Study.

PubMed

Takachi, Ribeka; Inoue, Manami; Shimazu, Taichi; Sasazuki, Shizuka; Ishihara, Junko; Sawada, Norie; Yamaji, Taiki; Iwasaki, Motoki; Iso, Hiroyasu; Tsubono, Yoshitaka; Tsugane, Shoichiro

2010-02-01

Although the influence of salt, per se, on the risk of cancer or cardiovascular disease (CVD) might differ from that of salt-preserved foods, few studies have simultaneously examined the effects of sodium and salted foods on the risk of either cancer or CVD. We simultaneously examined associations between sodium and salted food consumption and the risk of cancer and CVD. During 1995-1998, a validated food-frequency questionnaire was administered to 77,500 men and women aged 45-74 y. During up to 598,763 person-years of follow-up until the end of 2004, 4476 cases of cancer and 2066 cases of CVD were identified. Higher consumption of sodium was associated with a higher risk of CVD but not with the risk of total cancer: multivariate hazard ratios for the highest compared with lowest quintiles of intake were 1.19 (95% CI: 1.01, 1.40; P for trend: 0.06) for CVD and 1.04 (95% CI: 0.93, 1.16; P for trend: 0.63) for total cancer. Higher consumption of salted fish roe was associated with higher risk of total cancer, and higher consumption of cooking and table salt was associated with higher risk of CVD. Similar results were seen for the risk of gastric or colorectal cancer and stroke. Sodium intake as a whole salt equivalent may not increase the risk of cancer but may increase that of CVD. In contrast, salted food intake may increase the risk of cancer. Our findings support the notion that sodium and salted foods have differential influences on the development of cancer and CVD.

Using a Cell Phone to Investigate the Skin Depth Effect in Salt Water

NASA Astrophysics Data System (ADS)

Rayner, John

2017-02-01

This paper describes an experimental investigation of the skin depth effect for electromagnetic waves in salt water using a cell phone that is immersed to a critical depth where it no longer responds when called. We show that this critical depth is directly proportional to the theoretical skin depth for a range of salt concentrations.

Using a Cell Phone to Investigate the Skin Depth Effect in Salt Water

ERIC Educational Resources Information Center

Rayner, John

2017-01-01

This paper describes an experimental investigation of the skin depth effect for electromagnetic waves in salt water using a cell phone that is immersed to a critical depth where it no longer responds when called. We show that this critical depth is directly proportional to the theoretical skin depth for a range of salt concentrations.

Trophic shift in young-of-the-year Mugilidae during salt-marsh colonization.

PubMed

Lebreton, B; Richard, P; Guillou, G; Blanchard, G F

2013-04-01

This study investigated the trophic shift of young-of-the-year (YOY) thinlip grey mullet Liza ramada and golden grey mullet Liza aurata during their recruitment in a salt marsh located on the European Atlantic Ocean coast. Stable-isotope signatures (δ(13) C and δ(15) N) of the fishes followed a pattern, having enrichments in (13) C and (15) N with increasing fork length (LF ): δ(13) C in fishes < 30 mm ranged from -19.5 to -15.0‰, whereas in fishes > 30 mm δ(13) C ranged from -15.8 to -12.7‰, closer to the level in salt-marsh food resources. Large differences between the δ(15) N values of mugilids and those of food sources (6·0‰ on average) showed that YOY are secondary consumers, similar to older individuals, when feeding in the salt marsh. YOY mugilids shift from browsing on pelagic prey to grazing on benthic resources from the salt marsh before reaching 30 mm LF. The results highlight the role of European salt marshes as nurseries for juvenile mugilids. © 2013 The Authors. Journal of Fish Biology © 2013 The Fisheries Society of the British Isles.

New insights on the rheological properties of a rocksalt

NASA Astrophysics Data System (ADS)

Speranza, G.; Vinciguerra, S.; Di Genova, D.; Romano, C.; Vona, A.; Mollo, S.; Iarocci, A.

2013-12-01

The importance and economic interest on rocksalt deposits and salt bodies are well known and extensively studied. The physical and mechanical properties of salt have a profound influence on the tectonics as well as they are considered to be vital for applicative purposes such as mining, petroleum and nuclear waste storage. However, previous scientific works have mainly focused on synthetic rocksalt or commercial salt, whereas natural salt facies have been scarcely investigated. In this view, we present new data on the role of natural heterogeneities (i.e., relative abundance of primary salt crystals and impurities) on the rheological parameters of a rocksalt. This rock belongs to the Saline di Volterra formation (Volterra basin, Tuscany, central Italy) that was deposited during the Messinian Salinity Crisis. The 49-metre-thick salt sequence (intersected by the S1113 borehole of the Solvay company) is characterized by a high salt facies variability. In particular, three end-members have been recognized: the first contains abundant primary salt crystals, with minor or no recrystallizazion; the second member is extensively recrystallized, with scarce primary crystal remnants; the third shows a great abundance of clay impurities. Rheological parameters, such as static and dynamic Young's Modulus and coefficient of linear expansion, were measured for the three rocksalt end-members throughout P and S seismic velocities, uniaxial compressive strength and thermal expansion measurements. Seismic velocity has been measured on cubic samples with a side ranging from 4 to 7 cm. A clear effect of the salt facies was found: the average velocity is faster in mostly recrystallized salt samples (4500 m/s), slower in primary salt-rich samples (4300 m/s), and intermediate (4350 m/s) in presence of clay impurities. Dynamic Young's Modulus calculated on velocities (average value ≈ 38 GPa) mirrors this behavior, with lowest values related to primary salt. The anisotropic effect induced by the deformation is evident considering the wave velocities measured for each axis of the cubes, with lower velocities along the Z (vertical) axis. Uniaxial compressive tests (carried out at ambient temperature) revealed the effect of the salt facies in the mechanical properties and, particularly, in the elastic properties and in the absolute peak stress value. Static Young's Moduli (average value ≈ 5,3 GPa) result much lower than the dynamic ones. In this case lowest values are related to recrystallized salt. Notably, the peak stress is inversely proportional to the static Young's Moduli. Moreover, data from thermal expansion curves (from 20 to 700 °C) show a greater amount of volume expansion of primary salt and allowed to identify an 'instability zone', between 300 and 500 °C, where fluid emission, samples cracking and a sudden increase in volume expansivity occur. Results from our experiments indicate that the different characteristics of salt facies determine the bulk rheological parameters and, consequently, the rocksalt deformation behavior. Although further analyses are necessary, we suggest that studies on salt bodies cannot be approached without detailed petrophysical and rheological analyses of rocksalt facies.

9 CFR 96.10 - Uncertified casings; transportation for disinfection; original shipping containers; disposition...

Code of Federal Regulations, 2011 CFR

2011-01-01

... hydroxide (Lye) prepared in a fresh solution in the proportion of not less than 1 pound avoirdupois of... in case any of the sodium hydroxide solution should come in contact with the body. (2) This solution...) Dissolve the salt in the proportion of 90 pounds of salt to 100 gallons of water. Add 23/4 gallons of C. P...

9 CFR 96.10 - Uncertified casings; transportation for disinfection; original shipping containers; disposition...

Code of Federal Regulations, 2014 CFR

2014-01-01

... hydroxide (Lye) prepared in a fresh solution in the proportion of not less than 1 pound avoirdupois of... in case any of the sodium hydroxide solution should come in contact with the body. (2) This solution...) Dissolve the salt in the proportion of 90 pounds of salt to 100 gallons of water. Add 23/4 gallons of C. P...

9 CFR 96.10 - Uncertified casings; transportation for disinfection; original shipping containers; disposition...

Code of Federal Regulations, 2013 CFR

2013-01-01

... hydroxide (Lye) prepared in a fresh solution in the proportion of not less than 1 pound avoirdupois of... in case any of the sodium hydroxide solution should come in contact with the body. (2) This solution...) Dissolve the salt in the proportion of 90 pounds of salt to 100 gallons of water. Add 23/4 gallons of C. P...

Physical chemistry and evolution of salt tolerance in halobacteria

NASA Technical Reports Server (NTRS)

Lanyi, J. K.

1980-01-01

The cellular constituents of extremely halophilic bacteria not only tolerate high salt concentration, but in many cases require it for optical functioning. The characteristics affected by salt include enzyme activity, stability, allosteric regulation, conformation and subunit association. The salt effects are of two major kinds: electrostatic shielding of negative charges by cations at low salt concentration, and hydrophobic stabilization by salting-out type salts at high salt concentration. The composition of halobacterial proteins shows an excess of acidic amino acids and a deficiency of nonpolar amino acids, which accounts for these effects. Since the cohesive forces are weaker and the repulsing forces are stronger in these proteins, preventing aggregation in salt, these structures are no longer suited for functioning in the absence of high salt concentrations. Unlike these nonspecific effects, ribosomes in halobacteria show marked preference for potassium over sodium ions. To ensure the proper intracellular ionic composition, powerful ion transport systems have evolved in the halobacteria, resulting in the extrusion of sodium ions and their replacement by potassium. It is likely that such membrane transport system for ionic movements is a necessary requisite for salt tolerance.

A molten salt process for producing neodymium and neodymium-iron alloys

NASA Astrophysics Data System (ADS)

Sharma, Ram A.; Seefurth, Randall N.

1989-12-01

The production of low-cost neodymium metal in a stirred tank reactor by the reduction of Nd2O3 with sodium in the presence of CaCl2-KCl-NaCl melts by the overall reaction Nd2O3+3CaCl2+6Na→2Nd+3CaO+6NaCl at ˜750 °C is described. The metal produced is recovered from the salt medium by dissolving it in a Nd-Zn or Nd-Fe alloy pool. In the case of Nd-Zn alloy pools, product yields (percentages of theoretical neodymium produced) in excess of 94 pct are obtained when using salt ratios, i.e., the amounts of salt per gram of neodymium produced, ≥3.5 and excess reductant ≥10 pct. The alloy produced is of high quality, and following vacuum distillation of the zinc, can be used in producing General Motors’ MAGNEQUENCH alloy for permanent magnets. In the case of Nd-Fe pools, the yield is also ˜95 pct with a salt ratio as low as 3.5. The yield is found to depend on the salt composition and salt ratio, and to decrease at salt ratios below 3.25. Stirrer position has little effect on yield, while increasing the temperature and placing fins in the reactor increase the yield. The Nd-Fe alloy produced is of as good quality as that produced using Ca reductant and is suitable for direct use in preparing the MAGNEQUENCH alloy.

Cerebral salt-wasting syndrome due to hemorrhagic brain infarction: a case report.

PubMed

Tanaka, Tomotaka; Uno, Hisakazu; Miyashita, Kotaro; Nagatsuka, Kazuyuki

2014-07-23

Cerebral salt-wasting syndrome is a condition featuring hyponatremia and dehydration caused by head injury, operation on the brain, subarachnoid hemorrhage, brain tumor and so on. However, there are a few reports of cerebral salt-wasting syndrome caused by cerebral infarction. We describe a patient with cerebral infarction who developed cerebral salt-wasting syndrome in the course of hemorrhagic transformation. A 79-year-old Japanese woman with hypertension and arrhythmia was admitted to our hospital for mild consciousness disturbance, conjugate deviation to right, left unilateral spatial neglect and left hemiparesis. Magnetic resonance imaging revealed a broad ischemic change in right middle cerebral arterial territory. She was diagnosed as cardiogenic cerebral embolism because atrial fibrillation was detected on electrocardiogram on admission. She showed hyponatremia accompanied by polyuria complicated at the same time with the development of hemorrhagic transformation on day 14 after admission. Based on her hypovolemic hyponatremia, she was evaluated as not having syndrome of inappropriate secretion of antidiuretic hormone but cerebral salt-wasting syndrome. She fortunately recovered with proper fluid replacement and electrolyte management. This is a rare case of cerebral infarction and cerebral salt-wasting syndrome in the course of hemorrhagic transformation. It may be difficult to distinguish cerebral salt-wasting syndrome from syndrome of inappropriate antidiuretic hormone, however, an accurate assessment is needed to reveal the diagnosis of cerebral salt-wasting syndrome because the recommended fluid management is opposite in the two conditions.

Potentials and problems of sustainable irrigation with water high in salts

NASA Astrophysics Data System (ADS)

Ben-Gal, Alon

2015-04-01

Water scarcity and need to expand agricultural productivity have led to ever growing utilization of poor quality water for irrigation of crops. Almost in all cases, marginal or alternative water sources for irrigation contain relatively high concentrations of dissolved salts. When salts are present, irrigation water management, especially in the dry regions where water requirements are highest, must consider leaching in addition to crop evapotranspiration requirements. Leaching requirements for agronomic success are calculable and functions of climate, soil, and very critically, of crop sensitivity and the actual salinity of the irrigation water. The more sensitive the crop and more saline the water, the higher the agronomic cost and the greater the quantitative need for leaching. Israel is a forerunner in large-scale utilization of poor quality water for irrigation and can be used as a case study looking at long term repercussions of policy alternatively encouraging irrigation with recycled water or brackish groundwater. In cases studied in desert conditions of Israel, as much of half of the water applied to crops including bell peppers in greenhouses and date palms is actually used to leach salts from the root zone. The excess water used to leach salts and maintain agronomic and economic success when irrigating with water containing salts can become an environmental hazard, especially in dry areas where natural drainage is non-existent. The leachate often contains not only salts but also agrochemicals including nutrients, and natural contaminants can be picked up and transported as well. This leachate passes beyond the root zone and eventually reaches ground or surface water resources. This, together with evidence of ongoing increases in sodium content of fresh produce and increased SAR levels of soils, suggest that the current policy and practice in Israel of utilization of high amounts of low quality irrigation water is inherently non- sustainable. Current trends and technologies allowing economically feasible desalination at large scales present a sustainable alternative where salts are removed from water prior to irrigation.

Field-scale Thermal Testing in a Generic Salt Disposal Environment Underground Research Laboratory (URL): Delineation of Principal Purpose Objectives and Hypotheses

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sassani, David C.; Hardin, Ernest L.; Kuhlman, Kristopher L

The amount of brine present in domal salt formation is far less than in bedded salts (e.g., 0.01 to 0.1% compared with 1 to 3%). In salt domes, shear deformation associated with diapirism has caused existing brine to coalesce, leading to flow and expulsion. Brine migration behavior was investigated in bedded salt at WIPP (Nowak and McTigue 1987, SAND87-0880), and in domal salt at Asse (Coyle et al. 1987, BMI/ONWI-624). Test methods were not standardized, and the tests involved large diameter boreholes (17 to 36 in. diameter) and large apparatus. The tested intervals were proximal to mined openings (within approximatelymore » 1 diameter) where in situ stresses are redistributed due to excavation. The tests showed that (1) brine inflow rates can range over at least 2 orders of magnitude for domal vs. bedded salt, (2) that brine inflow is strongly associated with clay and interbedded permeable layers in bedded salt, and (3) that measurement systems can readily collect very small quantities of moisture over time frames of 2 years or longer. Brine inflow rates declined slightly with time in both test series, but neither series approached a state of apparent depletion. This range of flow magnitude could be significant to repository design and performance assessment, especially if inflow rates can be predicted using stratigraphic and geomechanical inputs, and can be shown to approach zero in a predictable manner.« less

Photoimageable composition

DOEpatents

Dentinger, Paul; Krafick, Karen L.; Simison, Kelby Liv

2005-02-22

The use of photoacid generators including an alkoxyphenylphenyliodonium salt and/or bis(t-butylphenyl)iodonium salt in a photoimageable composition helps improve resolution. Suitable photoimageable compositions includes: (a) a multifuctional polymeric epoxy resin that is dissolved in an organic solvent wherein the epoxy resin comprises oligomers of bisphenol A that is quantitatively protected by glycidyl ether and wherein the oligomers have an average functionality that ranges from about 3 to 12; and a photoacid generator comprising an alkoxyphenylphenyliodonium salt and/or bis(t-butylphenyl)iodonium salt. Preferred alkoxyphenylphenyliodonium salts include 4-octyloxyphenyl phenyliodonium hexafluoroantimonate and 4-methoxyphenyl phenyliodonium hexafluoroantimonate. The photoimageable composition is particularly suited for producing high aspect ratio microstructures.

Characteristic of molten fluoride salt system LiF-BeF2 (Flibe) and LiF-NaF-KF (Flinak) as coolant and fuel carrier in molten salt reactor (MSR)

NASA Astrophysics Data System (ADS)

Bahri, Che Nor Aniza Che Zainul; Al-Areqi, Wadee'ah Mohd; Ruf, Mohd'Izzat Fahmi Mohd; Majid, Amran Ab.

2017-01-01

Interest of fluoride salts have recently revived due to the high temperature application in nuclear reactors. Molten Salt Reactor (MSR) was designed to operate at high temperature in range 700 - 800°C and its fuel is dissolved in a circulating molten fluoride salt mixture. Molten fluoride salts are stable at high temperature, have good heat transfer properties and can dissolve high concentration of actinides and fission product. The aim of this paper was to discuss the physical properties (melting temperature, density and heat capacity) of two systems fluoride salt mixtures i.e; LiF-BeF2 (Flibe) and LiF-NaF-KF (Flinak) in terms of their application as coolant and fuel solvent in MSR. Both of these salts showed almost same physical properties but different applications in MSR. The advantages and the disadvantages of these fluoride salt systems will be discussed in this paper.

Microbiology of solar salt ponds

NASA Technical Reports Server (NTRS)

Javor, B.

1985-01-01

Solar salt ponds are shallow ponds of brines that range in salinity from that of normal seawater (3.4 percent) through NaCl saturation. Some salterns evaporate brines to the potash stage of concentration (bitterns). All the brines (except the bitterns, which are devoid of life) harbor high concentrations of microorganisms. The high concentrations of microorganisms and their adaptation to life in the salt pond are discussed.

ELASTICITY, DOUBLE REFRACTION AND SWELLING OF ISOELECTRIC GELATIN

PubMed Central

Kunitz, M.

1930-01-01

Quincke's researches (1904) have demonstrated that when a 20 per cent gelatin gel is allowed to swell in water it gives rise to positive double refraction, as if the gel were under tensile stresses. If, on the other hand, the gel shrinks on being placed in alcohol it becomes negatively double refractive, as if it were compressed. But the double refraction as found by Quincke lasts only during the process of swelling or shrinking, and disappears as soon as the gel reaches a state of equilibrium. This phenomenon was investigated here and it was found that the reason for the disappearance of the double refraction is due to the fact that at equilibrium the percentage change in the size of a gel is equal in all three dimensions and the strain is therefore uniform. Double refraction persists as long as there is a difference in the elastic strain in the three dimensions of the strained material. It was found that when gels are cast on glass slides or in glass frames, so as to prevent swelling in certain directions, the double refraction produced by swelling at 6°C. persists permanently in the gel as long as it is swollen, and is proportional to the percentage change in the linear dimensions of the gel. Gels made up of various concentrations of isoelectric gelatin of less than 10 per cent when placed in dilute buffer of the same pH as that of the isoelectric point of the gelatin shrink and give rise to negative double refraction, while gels of concentrations of more than 10 per cent swell and give rise to positive double refraction. The double refraction produced in either case when divided by the percentage change in the dimensions of the gel and by its changed concentration gives a constant value both for swelling and shrinking. This constant which stands for the double refraction produced in a gel of unit concentration per unit strain is termed here the optical modulus of elasticity since it is proportional to the internal elastic stress in the swollen gelatin. It was found that the optical modulus of elasticity is the same both for gels cast on slides and in frames, although the mode of swelling is different in the two forms of gels. Gels removed from their glass supports after apparent swelling equilibrium, when placed in dilute buffer, begin to swell gradually in all three dimensions and the double refraction decreases slowly, though it persists for a long time. But the double refraction per unit change in dimension and per unit concentration still remains the same as before, thus proving that the internal elastic stress as indicated by the double refraction is brought about by the resistance of the gel itself to deformation. A study was also made on the effect of salts, acid and base on the double refraction of a 10 per cent gel during swelling. The experiments show that below M/8 salts affect very slightly the optical modulus of elasticity of the gel. At higher concentrations of salts the elasticity of the gel is reduced by some salts and increased by others, while such salts as sodium acetate and sodium and ammonium sulfates do not change the elasticity of the gels at all during swelling. The investigated salts may thus be arranged in this respect in the following approximate series: CaCl2, NaI, NaSCN, NaBr, AlCl3, NaCl, Na acetate, Na2SO4, (NH4)2SO4, Al2SO4 and MgSO4. The first five in the series decrease the elasticity while the last two in the series increase the elasticity of the gels during swelling. Acids and bases in higher concentrations exert a powerful influence on the reduction of the elasticity of the gel but in the range of pH between 2.0 and 10.0 the elasticity remains unaffected. The general conclusions to be drawn from these studies are as follows: 1. Swelling or shrinking produces elastic stresses in gels of gelatin, tensile in the first case and compressive in the second case, both being proportional to the percentage change in the dimensions of the gel. 2. Unsupported gels when immersed in aqueous solutions swell or shrink in such a manner that at equilibrium the percentage change in size is equal in all three dimensions, and the stresses become equalized throughout the gel. 3. Gels cast on glass slides or in frames when immersed in aqueous solutions swell or shrink mostly in one direction, and give rise to unidirectional stresses that can be determined accurately by measuring the double refraction produced. 4. The modulus of elasticity of swelling gelatin gels, as calculated from the double refraction measurements, is the same both for compression and for tension and is proportional to the concentration of gelatin in the gel. 5. The modulus of elasticity of gels during swelling is affected only slightly or not at all by salts at concentrations of less than M/8 and is independent of the pH in the range approximately between 2.0 and 10.0. 6. Higher concentrations of salts affect the modulus of elasticity of gelatin gels and the salts in their effectiveness may be arranged in a series similar to the known Hoffmeister series. 7. Acid and alkali have a strong reducing influence on the elastic modulus of swelling gels. 8. The swelling produced in isoelectric gelatin by salts is due primarily to a change brought about by the salts in the osmotic forces in the gel, but in high concentrations of some salts the swelling is increased by the influence of the salt on the elasticity of the gel. This agrees completely with the theory of swelling of isoelectric gelatin as developed by Northrop and the writer in former publications. 9. The studies of Loeb and the writer on the effect of salts on swelling of gelatin in acid and alkali have been in the range of concentrations of salts where the modulus of elasticity of the gelatin is practically constant, and the specific effect of the various salts has been negligible as compared with the effect of the valency of the ions. In concentrations of salts below M/4 or M/8 the Hoffmeister series plays no rôle. PMID:19872548

Magnetic properties of four Cu(ii)-amino acid salts

NASA Astrophysics Data System (ADS)

Calvo, Rafael

1984-03-01

We report a comparative study of magnetic properties of the Cu(II) salts of the amino acids l-alanine, dl-α-amino-n-butyric acid, α-amino isobutyric acid, and l-isoleucine. The position of the EPR lines of these quasi-two-dimensional magnetic systems was measured as a function of temperature T between 293 and 1.5 K, at 9.3 GHz and for magnetic fields applied along three axes of single crystal samples. Large changes of the gyromagnetic factor with T have been observed. They are attributed to an internal mean field, proportional to the applied field, which appears when the temperature is lowered due to short range magnetic order in the paramagnetic phase of the salts. The problem of short range magnetic order and g shifts in Cu-amino acid salts is discussed and compared with previous observations in Mn one-dimensional systems.

Organic carbon content of marine aerosols collected on Bermuda

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hoffman, E.J.; Duce, R.A.

1974-01-01

The concentration of total organic carbon in marine aerosols collected from a 20-m tower on the Southwest Coast of Bermuda ranged from 0.15 to 0.47 microgram/M/sup 3/ STP under onshore wind conditions. The mass of the organic carbon ranged from 1 to 19% of the mass of sea salt in the particles in Bermuda, and the percentage decreased with increasing salt content.

Systematic Evaluation of Salt Cavern Well Integrity

NASA Astrophysics Data System (ADS)

Roberts, B. L.; Lord, D. L.; Lord, A. S.; Bettin, G.; Sobolik, S. R.; Park, B. Y.

2017-12-01

The U.S. Strategic Petroleum Reserve (SPR) holds a reserve of crude oil ( 700 million barrels) to help ease any interruptions in oil import to the United States. The oil is stored in a set of 63 underground caverns distributed across four sites along the U.S. Gulf Coast. The caverns were solution mined into salt domes at each of the four sites. The plastic nature of the salt is beneficial for the storage of crude oil as it heals any fractures that may occur in the salt. The SPR is responsible for operating and maintaining the nearly 120 wells used to access the storage caverns over operational lifetimes spanning decades. Salt creep can induce deformation of the well casing which must be remediated to insure cavern and well integrity. This is particularly true at the interface between the plastic salt and the rigid caprock. The Department of Energy, the SPR Management and Operations contractor, and Sandia National Laboratories has developed a multidimensional well-grading system for the salt cavern access wells. This system is designed to assign numeric grades to each well indicating its risk of losing integrity and remediation priority. The system consists of several main components which themselves may consist of sub-components. The main components consider such things as salt cavern pressure history, results from geomechanical simulations modeling salt deformation, and measurements of well casing deformation due to salt creep. In addition, the geology of the salt domes and their overlying caprock is also included in the grading. These multiple factors are combined into summary values giving the monitoring and remediation priority for each well. Sandia National Laboratories is a multimission laboratory managed and operated by National Technology and Engineering Solutions of Sandia LLC, a wholly owned subsidiary of Honeywell International Inc. for the U.S. Department of Energy's National Nuclear Security Administration under contract DE-NA0003525.

Diclofenac salts. III. Alkaline and earth alkaline salts.

PubMed

Fini, Adamo; Fazio, Giuseppe; Rosetti, Francesca; Angeles Holgado, M; Iruín, Ana; Alvarez-Fuentes, Josefa

2005-11-01

Diclofenac salts containing the alkaline and two earth alkaline cations have been prepared and characterized by scanning electron microscopy (SEM) and EDAX spectroscopy; and by thermal and thermogravimetric analysis (TGA): all of them crystallize as hydrate when precipitated from water. The salts dehydrate at room temperature and more easily on heating, but recovery the hydration, when placed in a humid environment. X-ray diffraction spectra suggest that on dehydration new peaks appear on diffractograms and the lattice of the salts partially looses crystallinity. This phenomenon is readily visible in the case of the calcium and magnesium salts, whose thermograms display a crystallization exotherm, before melting or decomposing at temperatures near or above 200 degrees C; these last salts appear to form solvates, when prepared from methanol. The thermogram of each salt shows a complex endotherm of dehydration about 100 degrees C; the calcium salt displays two endotherms, well separated at about 120 and 160 degrees C, which disappear after prolonged heating. Decomposition exotherms, before or soon after the melting, appear below 300 degrees C. The ammonium salt is thermally unstable and, when heated to start dehydration, dissociates and leaves acidic diclofenac.

Meat consumption, meat cooking and risk of lung cancer among Uruguayan men.

PubMed

De Stefani, Eduardo; Ronco, Alvaro L; Boffetta, Paolo; Deneo-Pellegrini, Hugo; Acosta, Gisele; Mendilaharsu, María

2010-01-01

A case-control study was conducted in Uruguay, including 876 male cases of lung cancer and 876 male hospitalized controls, frequency matched for age (ten-year intervals), residence and hospital. The following explanatory variables were included in the study: fried red meat, barbecued red meat, boiled red meat, and salted red meat. These items were log transformed and energy-adjusted by the residuals method. The following potential confounders were included into the models: age, residence, hospital, education, family history of lung cancer, body mass index, smoking index, alcohol drinking, mate consumption, total energy intake, non-meat fatty foods and total fruits. The main objective was to estimate the odds ratios associated with lung cancer risk. Whereas fried meat, barbecued meat, and salted meat were positively associated with risk (OR of the highest quartile of salted meat versus the lowest, 2.90, 95 % CI 1.99-4.25, p-value for trend<0.0001), boiled red meat was mainly protective. We conclude that salted meat was the main risk factor. The mechanisms could be related to the content of N-nitroso compounds in salted meat.

Preferential deprotonation and conformational stability of dicarboxylic acids: A packing effect

NASA Astrophysics Data System (ADS)

Barooah, Nilotpal; Singh, W. Marjit; Baruah, Jubaraj B.

2008-03-01

Crystal structures of a series of salts of (6-carboxymethyl-1,3,5,7-tetraoxo-3,5,6,7-tetrahydro-1 H-pyrrolo[3,4- f]isoindol-2-yl)-acetic acid ( 1) and 2-carboxymethyl-1,3-dioxo-2,3-dihydro-1 H-isoinodole-5-carboxylic acid ( 2) with different polynuclear nitrogen containing heterocyclic compounds, namely, quinoline, 1,10-phenanthroline and 8-hydroxyquinoline are determined. In the case of salt of 1 with quinolinium and 1,10-phenanthrolinium cations syn disposition between the carboxylate anion and carboxylic acid groups is observed; whereas in the case of the 8-hydroxyquinolinium salt of 1, it is the anti disposition. It is also found that the solid state structure of 1,10-phenanthrolinium salt of 2 has deprotonation at the aromatic end, whereas in 8-hydroxy-quinolinium salt of 2 is formed by deprotonation of carboxylic acid group on the aliphatic side. The dicarboxylic acid 2 forms 1:2 co-crystals with quinoline. From crystallographic study it is shown that the weak interactions become prominent in stabilising the observed conformers and also in stabilising specific deprotonated species.

[The value of allergy survey in a retrospective series of 40 patients with burning-mouth syndrome (stomatodynia)].

PubMed

Machet, L; Le Dû, S; Bernez, A; Pillette-Delarue, M; Lelièvre, G; Hoarau, C; Hüttenberger, B; Vaillant, L

2008-02-01

By definition, stomatodynia or burning-mouth syndrome involves oral pain with no causes being found on history taking or examination. An allergic origin is often suspected by doctors and patients alike. In this study, we attempted to assess the value of epicutaneous tests in demonstrating allergic causes for patients presenting stomatodynia. This was a single-centre retrospective study of patients undergoing epicutaneous tests between 1996 and 2003 to screen for allergic causes of mouth pain not accounted for by any abnormalities seen during examination performed at consultations for mouth disease. Forty patients were included (11 male, 29 female; mean age: 58 years), and 39 were excluded. Sixteen patients presented at least one positive test, with a total of 35 positive tests in all. In decreasing order of frequency, the causes were metals, mercury derivatives (nickel salts: n=5; chrome salts: n=3; palladium salts: n=2; phenylmercuric acetate: n=2; thiomersal: n=2; cobalt salts: n=1; gold salts: n=1; mercury: n=1) and resins (acrylates: n=4). The relevance of these test results was considered probable in three cases and possible in five cases, associated with the existence of metals or resins in patients' mouths. The Peru balm test was positive in four cases but was not relevant. Tests for personal products were negative in all cases, with the exception of one case of resin from a prosthesis and one case of tixocortol pivalate. Type I stomatodynia (daily occurrence with gradually increase in discomfort throughout the day) and type II stomatodynia (permanent) are not normally attributable to allergies. However, for type III stomatodynia (non-permanent, with acute episodes followed by remission), an allergy survey guided by questioning may be undertaken to determine the cause, primarily prostheses or diet. The relevance of positive test results must be interpreted with caution in view of the incidence of positive epicutaneous tests for metals and Peru balm among the general population studied.

Target Salt 2025: A Global Overview of National Programs to Encourage the Food Industry to Reduce Salt in Foods

PubMed Central

Webster, Jacqui; Trieu, Kathy; Dunford, Elizabeth; Hawkes, Corinna

2014-01-01

Reducing population salt intake has been identified as a priority intervention to reduce non-communicable diseases. Member States of the World Health Organization have agreed to a global target of a 30% reduction in salt intake by 2025. In countries where most salt consumed is from processed foods, programs to engage the food industry to reduce salt in products are being developed. This paper provides a comprehensive overview of national initiatives to encourage the food industry to reduce salt. A systematic review of the literature was supplemented by key informant questionnaires to inform categorization of the initiatives. Fifty nine food industry salt reduction programs were identified. Thirty eight countries had targets for salt levels in foods and nine countries had introduced legislation for some products. South Africa and Argentina have both introduced legislation limiting salt levels across a broad range of foods. Seventeen countries reported reductions in salt levels in foods—the majority in bread. While these trends represent progress, many countries have yet to initiate work in this area, others are at early stages of implementation and further monitoring is required to assess progress towards achieving the global target. PMID:25195640

Target salt 2025: a global overview of national programs to encourage the food industry to reduce salt in foods.

PubMed

Webster, Jacqui; Trieu, Kathy; Dunford, Elizabeth; Hawkes, Corinna

2014-08-21

Reducing population salt intake has been identified as a priority intervention to reduce non-communicable diseases. Member States of the World Health Organization have agreed to a global target of a 30% reduction in salt intake by 2025. In countries where most salt consumed is from processed foods, programs to engage the food industry to reduce salt in products are being developed. This paper provides a comprehensive overview of national initiatives to encourage the food industry to reduce salt. A systematic review of the literature was supplemented by key informant questionnaires to inform categorization of the initiatives. Fifty nine food industry salt reduction programs were identified. Thirty eight countries had targets for salt levels in foods and nine countries had introduced legislation for some products. South Africa and Argentina have both introduced legislation limiting salt levels across a broad range of foods. Seventeen countries reported reductions in salt levels in foods-the majority in bread. While these trends represent progress, many countries have yet to initiate work in this area, others are at early stages of implementation and further monitoring is required to assess progress towards achieving the global target.

Recent changes in salt use and stroke mortality in England and Wales. Any help for the salt-hypertension debate?

PubMed Central

Cummins, R O

1983-01-01

This analysis attempts to fill the gap in the epidemiological evidence about the relation between dietary salt and hypertension. Changes in the purchase of salt in England and Wales are compared with changes in mortality from cerebrovascular disease (1958-78). Stroke mortality, a major sequel of hypertension, has declined in this period. Consumer purchases of salt have decreased also, as suggested by the National Food Survey. While these trends are consistent with the salt-hypertension hypothesis, the picture is confused by an increase in meals eaten outside the home, by the consumption of more processed food, and by a higher prevalence of refrigerators. Other events, such as medical treatment of hypertension or changes in the case fatality rate, could have contributed to the decline in stroke mortality. This secular trend analysis, using available data, does not clarify the salt-hypertension debate. PMID:6875440

Prediction of Greenhouse Gas (GHG) Fluxes from Coastal Salt Marshes using Artificial Neural Network

NASA Astrophysics Data System (ADS)

Ishtiaq, K. S.; Abdul-Aziz, O. I.

2017-12-01

Coastal salt marshes are among the most productive ecosystems on earth. Given the complex interactions between ambient environment and ecosystem biological exchanges, it is difficult to predict the salt marsh greenhouse gas (GHG) fluxes (CO2 and CH4) from their environmental drivers. In this study, we developed an artificial neural network (ANN) model to robustly predict the salt marsh GHG fluxes using a limited number of input variables (photosynthetically active radiation, soil temperature and porewater salinity). The ANN parameterization involved an optimized 3-layer feed forward Levenberg-Marquardt training algorithm. Four tidal salt marshes of Waquoit Bay, MA — incorporating a gradient in land-use, salinity and hydrology — were considered as the case study sites. The wetlands were dominated by native Spartina Alterniflora, and characterized by high salinity and frequent flooding. The developed ANN model showed a good performance (training R2 = 0.87 - 0.96; testing R2 = 0.84 - 0.88) in predicting the fluxes across the case study sites. The model can be used to estimate wetland GHG fluxes and potential carbon balance under different IPCC climate change and sea level rise scenarios. The model can also aid the development of GHG offset protocols to set monitoring guidelines for restoration of coastal salt marshes.

Investigation of phyco-remediation of road salt run-off with marine microalgae Nannochloropsis gaditana.

PubMed

Devasya, Roopa; Bassi, Amarjeet

2017-11-15

Phyco-remediation is an environmental-friendly method, which involves the application of beneficial microalgae to treat wastewater-containing pollutants for a diverse range of conditions. Several industrial processes generate hyper saline wastewater, which is a significant challenge for conventional wastewater treatment, and the disposal of saline waters also has a negative impact on the environment. Road salt run-off is one such saline wastewater stream not currently treated and one that contributes significantly to negatively impacting receiving bodies of water. In this study, Nannochloropsis microalgae were able to assimilate >95% of the nitrates within 8 days in road salt concentrations ranging from 2.6% to 4.4% under phototrophic cultivation mode. Biomass yields of 1-2 g/l of culture were obtained with the maximum lipid of 22% (g/g) biomass in the road salt media. The crude road salt media provided all the essential micronutrients needed for algal cultivation. The fatty acid composition analysis of the obtained lipid composed of C16 and C18 over 45% of FAME are suitable for biofuel. This study has established that the use of road salt containing nitrate and phosphate nutrients will support the growth of marine micro algae for remediation of a waste water system that are the concern at winter-prevalent regions.

Direct Analysis of Proteins from Solutions with High Salt Concentration Using Laser Electrospray Mass Spectrometry

NASA Astrophysics Data System (ADS)

Karki, Santosh; Shi, Fengjian; Archer, Jieutonne J.; Sistani, Habiballah; Levis, Robert J.

2018-05-01

The detection of lysozyme, or a mixture of lysozyme, cytochrome c, and myoglobin, from solutions with varying salt concentrations (0.1 to 250 mM NaCl) is compared using laser electrospray mass spectrometry (LEMS) and electrospray ionization-mass spectrometry (ESI-MS). Protonated protein peaks were observed up to a concentration of 250 mM NaCl in the case of LEMS. In the case of ESI-MS, a protein solution with salt concentration > 0.5 mM resulted in predominantly salt-adducted features, with suppression of the protonated protein ions. The constituents in the mixture of proteins were assignable up to 250 mM NaCl for LEMS and were not assignable above a NaCl concentration of 0.5 mM for ESI. The average sodium adducts (< n >) bound to the 7+ charge state of lysozyme for LEMS measurements from salt concentrations of 2.5, 25, 50, and 100 mM NaCl are 1.71, 5.23, 5.26, and 5.11, respectively. The conventional electrospray measurements for lysozyme solution containing salt concentrations of 0.1, 1, 2, and 5 mM NaCl resulted in < n > of 2.65, 6.44, 7.57, and 8.48, respectively. LEMS displays an approximately two orders of magnitude higher salt tolerance in comparison with conventional ESI-MS. The non-equilibrium partitioning of proteins on the surface of the charged droplets is proposed as the mechanism for the high salt tolerance phenomena observed in the LEMS measurements. [Figure not available: see fulltext.

Direct Analysis of Proteins from Solutions with High Salt Concentration Using Laser Electrospray Mass Spectrometry

NASA Astrophysics Data System (ADS)

Karki, Santosh; Shi, Fengjian; Archer, Jieutonne J.; Sistani, Habiballah; Levis, Robert J.

2018-03-01

The detection of lysozyme, or a mixture of lysozyme, cytochrome c, and myoglobin, from solutions with varying salt concentrations (0.1 to 250 mM NaCl) is compared using laser electrospray mass spectrometry (LEMS) and electrospray ionization-mass spectrometry (ESI-MS). Protonated protein peaks were observed up to a concentration of 250 mM NaCl in the case of LEMS. In the case of ESI-MS, a protein solution with salt concentration > 0.5 mM resulted in predominantly salt-adducted features, with suppression of the protonated protein ions. The constituents in the mixture of proteins were assignable up to 250 mM NaCl for LEMS and were not assignable above a NaCl concentration of 0.5 mM for ESI. The average sodium adducts (< n >) bound to the 7+ charge state of lysozyme for LEMS measurements from salt concentrations of 2.5, 25, 50, and 100 mM NaCl are 1.71, 5.23, 5.26, and 5.11, respectively. The conventional electrospray measurements for lysozyme solution containing salt concentrations of 0.1, 1, 2, and 5 mM NaCl resulted in < n > of 2.65, 6.44, 7.57, and 8.48, respectively. LEMS displays an approximately two orders of magnitude higher salt tolerance in comparison with conventional ESI-MS. The non-equilibrium partitioning of proteins on the surface of the charged droplets is proposed as the mechanism for the high salt tolerance phenomena observed in the LEMS measurements. [Figure not available: see fulltext.

First light of a laser frequency comb at SALT

NASA Astrophysics Data System (ADS)

Depagne, Éric; McCracken, Richard A.; Reid, Derryck T.; Kuhn, Rudi B.; Erasmus, Nicolas; Crause, Lisa A.

2016-08-01

We present preliminary results of the commissioning and testing of SALT-CRISP (SALT-Calibration Ruler for Increased Spectrograph Precision), a Laser Frequency Comb (LFC) built by Heriot-Watt University and temporarily installed at the Southern African Large Telescope (SALT). The comb feeds the High Stability mode of SALT's High Resolution Spectrograph (HRS) and fully covers the wavelength range of the red channel of the HRS: 555-890 nm. The LFC provides significantly improved wavelength calibration compared to a standard Thorium-Argon (ThAr) lamp and hence offers unprecedented opportunities to characterise the resolution, stability and radial velocity precision of the HRS. Results from this field trial will be incorporated into subsequent LFC designs.

Projected Salt Waste Production from a Commercial Pyroprocessing Facility

DOE Office of Scientific and Technical Information (OSTI.GOV)

Simpson, Michael F.

Pyroprocessing of used nuclear fuel inevitably produces salt waste from electrorefining and/or oxide reduction unit operations. Various process design characteristics can affect the actual mass of such waste produced. This paper examines both oxide and metal fuel treatment, estimates the amount of salt waste generated, and assesses potential benefit of process options to mitigate the generation of salt waste. For reference purposes, a facility is considered in which 100 MT/year of fuel is processed. Salt waste estimates range from 8 to 20 MT/year from considering numerous scenarios. It appears that some benefit may be derived from advanced processes for separatingmore » fission products from molten salt waste, but the degree of improvement is limited. Waste form production is also considered but appears to be economically unfavorable. Direct disposal of salt into a salt basin type repository is found to be the most promising with respect to minimizing the impact of waste generation on the economic feasibility and sustainability of pyroprocessing.« less

Identification and characterization of microRNAs related to salt stress in broccoli, using high-throughput sequencing and bioinformatics analysis.

PubMed

Tian, Yunhong; Tian, Yunming; Luo, Xiaojun; Zhou, Tao; Huang, Zuoping; Liu, Ying; Qiu, Yihan; Hou, Bing; Sun, Dan; Deng, Hongyu; Qian, Shen; Yao, Kaitai

2014-09-03

MicroRNAs (miRNAs) are a new class of endogenous regulators of a broad range of physiological processes, which act by regulating gene expression post-transcriptionally. The brassica vegetable, broccoli (Brassica oleracea var. italica), is very popular with a wide range of consumers, but environmental stresses such as salinity are a problem worldwide in restricting its growth and yield. Little is known about the role of miRNAs in the response of broccoli to salt stress. In this study, broccoli subjected to salt stress and broccoli grown under control conditions were analyzed by high-throughput sequencing. Differential miRNA expression was confirmed by real-time reverse transcription polymerase chain reaction (RT-PCR). The prediction of miRNA targets was undertaken using the Kyoto Encyclopedia of Genes and Genomes (KEGG) Orthology (KO) database and Gene Ontology (GO)-enrichment analyses. Two libraries of small (or short) RNAs (sRNAs) were constructed and sequenced by high-throughput Solexa sequencing. A total of 24,511,963 and 21,034,728 clean reads, representing 9,861,236 (40.23%) and 8,574,665 (40.76%) unique reads, were obtained for control and salt-stressed broccoli, respectively. Furthermore, 42 putative known and 39 putative candidate miRNAs that were differentially expressed between control and salt-stressed broccoli were revealed by their read counts and confirmed by the use of stem-loop real-time RT-PCR. Amongst these, the putative conserved miRNAs, miR393 and miR855, and two putative candidate miRNAs, miR3 and miR34, were the most strongly down-regulated when broccoli was salt-stressed, whereas the putative conserved miRNA, miR396a, and the putative candidate miRNA, miR37, were the most up-regulated. Finally, analysis of the predicted gene targets of miRNAs using the GO and KO databases indicated that a range of metabolic and other cellular functions known to be associated with salt stress were up-regulated in broccoli treated with salt. A comprehensive study of broccoli miRNA in relation to salt stress has been performed. We report significant data on the miRNA profile of broccoli that will underpin further studies on stress responses in broccoli and related species. The differential regulation of miRNAs between control and salt-stressed broccoli indicates that miRNAs play an integral role in the regulation of responses to salt stress.

Bamboo salt attenuates CCl4-induced hepatic damage in Sprague-Dawley rats

PubMed Central

Zhao, Xin; Song, Jia-Le; Kil, Jeung-Ha

2013-01-01

Bamboo salt, a Korean folk medicine, is prepared with solar salt (sea salt) and baked several times at high temperatures in a bamboo case. In this study, we compared the preventive effects of bamboo salt and purified and solar salts on hepatic damage induced by carbon tetrachloride in Sprague-Dawley rats. Compared with purified and solar salts, bamboo salts prevented hepatic damage in rats, as evidenced by significantly reduced serum levels of aspartate aminotransferase, alanine aminotransferase, and lactate dehydrogenase (P < 0.05). Bamboo salt (baked 9×) triggered the greatest reduction in these enzyme levels. In addition, it also reduced the levels of the proinflammatory cytokines interleukin (IL)-6, interferon (IFN)-γ, and tumor necrosis factor (TNF)-α. Histopathological sections of liver tissue demonstrated the protective effect of bamboo salt, whereas sections from animals treated with the other salt groups showed a greater degree of necrosis. We also performed reverse transcription-polymerase chain reaction and western blot analyses of the inflammation-related genes iNOS, COX-2, TNF-α, and IL-1β in rat liver tissues. Bamboo salt induced a significant decrease (~80%) in mRNA and protein expression levels of COX-2, iNOS, TNF-α, and IL-1β, compared with the other salts. Thus, we found that baked bamboo salt preparations could prevent CCl4-induced hepatic damage in vivo. PMID:23964314

Cardiovascular disease and impoverishment averted due to a salt reduction policy in South Africa: an extended cost-effectiveness analysis.

PubMed

Watkins, David A; Olson, Zachary D; Verguet, Stéphane; Nugent, Rachel A; Jamison, Dean T

2016-02-01

The South African Government recently set targets to reduce cardiovascular disease (CVD) by lowering salt consumption. We conducted an extended cost-effectiveness analysis (ECEA) to model the potential health and economic impacts of this salt policy. We used surveys and epidemiologic studies to estimate reductions in CVD resulting from lower salt intake. We calculated the average out-of-pocket (OOP) cost of CVD care, using facility fee schedules and drug prices. We estimated the reduction in OOP expenditures and government subsidies due to the policy. We estimated public and private sector costs of policy implementation. We estimated financial risk protection (FRP) from the policy as (1) cases of catastrophic health expenditure (CHE) averted or (2) cases of poverty averted. We also performed a sensitivity analysis. We found that the salt policy could reduce CVD deaths by 11%, with similar health gains across income quintiles. The policy could save households US$ 4.06 million (2012) in OOP expenditures (US$ 0.29 per capita) and save the government US$ 51.25 million in healthcare subsidies (US$ 2.52 per capita) each year. The cost to the government would be only US$ 0.01 per capita; hence, the policy would be cost saving. If the private sector food reformulation costs were passed on to consumers, food expenditures would increase by <0.2% across all income quintiles. Preventing CVD could avert 2400 cases of CHE or 2000 cases of poverty yearly. Our results were sensitive to baseline CVD mortality rates and the cost of treatment. We conclude that, in addition to health gains, population salt reduction can have positive economic impacts-substantially reducing OOP expenditures and providing FRP, particularly for the middle class. The policy could also provide large government savings on health care. © The Author 2015. Published by Oxford University Press in association with The London School of Hygiene and Tropical Medicine.

Utah: Salt Lake Region

Atmospheric Science Data Center

2014-05-15

... scheduled events are at city (indoor) locations, and five in mountain (outdoor) facilities. All ten can be found within the area contained ... Lake City is surrounded by mountains including the Wasatch Range to the east, and the temperature difference between the Great Salt Lake ...

Comparison of characteristic of soils with and without salt crust soils in a hyper-arid floodplain

NASA Astrophysics Data System (ADS)

LI, X.; Feng, G.

2017-12-01

Soil salt crusts have been shown to restrict soil erosion, and influence the water and salt movement in soil, was great concern in the world. However, there is little information for the comparison of characteristic of soil with and without salt crust in a hyper-arid flood plains. The objective of this study was to investigate paired samples of salt crusts and the surface soil without a salt curst in the flood plain of Tarim River in China. The results revealed that the salt crust soils most distributed in shrubland dominated by Tarimax, in which account for 73%, the wetland was followed, with shallower groundwater table (<2.4 m). The salt crust was comprised of salt greater than 109 g·kg-1, crust was not found on the soils as its salt content less than 89 g·kg-1. The salt content of soils either with crust or without crust ranged from 89 to 109 g·kg-1. The salt crust thickness had positive correlation with salt content (R2=0.61), and also with crust strength (R2=0.64). Compared with soils without salt crust, the salt crust soils had more clay, silt and soil organic matter content. It was found that those soils were located in low-lying area, experience relatively higher frequent overflowing flood. This study revealed that the flood did not reduce salt content in top soils. Salt crust was probably formed due to salt accumulation from shallow groundwater (e.g. <2.4 m) in this region.

Failure Analysis of Overhanging Blocks in the Walls of a Gas Storage Salt Cavern: A Case Study

NASA Astrophysics Data System (ADS)

Wang, Tongtao; Yang, Chunhe; Li, Jianjun; Li, Jinlong; Shi, Xilin; Ma, Hongling

2017-01-01

Most of the rock salt of China is bedded, in which non-salt layers and rock salt layers alternate. Due to the poor solubility of the non-salt layers, many blocks overhang on the walls of the caverns used for gas storage, constructed by water leaching. These overhanging blocks may collapse at any time, which may damage the tubing and casing string, and even cause instability of the cavern. They are one of the main factors threatening the safety of caverns excavated in bedded rock salt formations. In this paper, a geomechanical model of the JJKK-D salt cavern, located in Jintan salt district, Jintan city, Jiangsu province, China, is established to evaluate the stability of the overhanging blocks on its walls. The characters of the target formation, property parameters of the rock mass, and actual working conditions are considered in the geomechanical model. An index system composed of stress, displacement, plastic zone, safety factor, and equivalent strain is used to predict the collapse length of the overhanging blocks, the moment the collapse will take place, and the main factors causing the collapse. The sonar survey data of the JJKK-D salt cavern are used to verify the reliability and accuracy of the proposed geomechanical model. The results show that the proposed geomechanical model has a good reliability and accuracy, and can be used for the collapse prediction of the overhanging blocks on the wall of the JJKK-D salt cavern. The collapse length of the overhanging block is about 8 m. We conclude that the collapse takes place during the debrining. The reason behind the collapse is the sudden decrease of the fluid density, leading to the increase of the self-weight of the overhanging blocks. This study provides a basis for the collapse prediction method of the overhanging blocks of Jintan salt cavern gas storage, and can also serve as a reference for salt cavern gas storage with similar conditions to deal with overhanging blocks.

Sea salts as a potential source of food spoilage fungi.

PubMed

Biango-Daniels, Megan N; Hodge, Kathie T

2018-02-01

Production of sea salt begins with evaporation of sea water in shallow pools called salterns, and ends with the harvest and packing of salts. This process provides many opportunities for fungal contamination. This study aimed to determine whether finished salts contain viable fungi that have the potential to cause spoilage when sea salt is used as a food ingredient by isolating fungi on a medium that simulated salted food with a lowered water activity (0.95 a w ). The viable filamentous fungi from seven commercial salts were quantified and identified by DNA sequencing, and the fungal communities in different salts were compared. Every sea salt tested contained viable fungi, in concentrations ranging from 0.07 to 1.71 colony-forming units per gram of salt. In total, 85 fungi were isolated representing seven genera. One or more species of the most abundant genera, Aspergillus, Cladosporium, and Penicillium was found in every salt. Many species found in this study have been previously isolated from low water activity environments, including salterns and foods. We conclude that sea salts contain many fungi that have potential to cause food spoilage as well as some that may be mycotoxigenic. Copyright © 2017 The Authors. Published by Elsevier Ltd.. All rights reserved.

Investigation of the source of residual phthalate in sundried salt.

PubMed

Kim, Jin Hyo; Lee, Jin Hwan; Kim, So-Young

2014-03-01

Phthalate contamination in sundried salt has recently garnered interest in Korea. Phthalate concentrations were investigated in Korean sundried salts, source waters, and aqueous extracts from polyvinyl chloride materials used in salt ponds. Preliminary screening results for phthalates in Korean sundried salts revealed that only di(2-ethylhexyl)phthalate (DEHP) was over the limit of detection, with an 8.6% detection rate, and the concentration ranged from below the limit of detection to 0.189 mg/kg. The tolerable daily intake contribution ratio of the salt was calculated to be only 0.001%. Residual phthalates were below 0.026 mg/liter in source water, and the aqueous extracted di-n-butylphthalate, benzylbutylphthalate, and DEHP, which are considered endocrine disruptors, were below 0.029 mg/kg as derived from the polyvinyl chloride materials in salt ponds. The transfer ratios of the six phthalates from seawater to sundried salts were investigated; transfer ratio was correlated with vapor pressure (r(2) = 0.9875). Thus, di-n-butylphthalate, benzylbutylphthalate, DEHP, and di-n-octylphthalate can be considered highly likely residual pollutants in some consumer salts.

Raman and Brillouin scattering of LiClO4 complexed in poly(propylene-glycol)

NASA Astrophysics Data System (ADS)

Schantz, S.; Torell, L. M.; Stevens, J. R.

1988-08-01

Raman spectra of LiClO4 complexed in poly(propylene-glycol) (PPG) have been obtained for concentrations of the monomer to salt ratio (ether oxygen):Li in the range 30:1-5:1. Splitting of the symmetric stretching mode of the ClO4- anion was observed with an intensity profile that varied with salt concentration. This phenomenon indicates a changing environment about the anion. A two-component band analysis leads to the identification of dissociated ions on one hand and solvent-separated ion pairs on the other. The concentration of ion pairs is relatively low compared to that of the dissociated ions, which are predominant for all concentrations. Despite the observed increase in the absolute number of dissociated ions at higher salt concentration, the electrical conductivity is reported to decrease in the same range. This indicates that the number of ``free'' charge carriers is of less importance for the conductivity than the mobility, which is damped in this concentration range. Frequency shifts of the disordered longitudinal-acoustic mode and increased hypersonic velocities, measured with Raman and Brillouin scattering techniques, respectively, indicate increased stiffness of the polymer matrix for increasing salt concentration, which probably results in decreased ion mobility.

Solubility of uranium oxide in molten salt electrolysis bath of LiF-BaF2 with LaF3 additive

NASA Astrophysics Data System (ADS)

Alangi, Nagaraj; Mukherjee, Jaya; Gantayet, L. M.

2016-03-01

The solubility of UO2 in the molten mixtures of equimolar LiF-BaF2(1:1) with LaF3 as additive was studied in the range of 1423 K-1523 K. The molten fluoride salt mixture LiF-BaF2 LaF3 was equilibrated with a sintered uranium oxide pellet at 1423 K, 1473 K, 1523 K and the salt samples were collected after equilibration. Studies were conducted in the range of 10%-50% by weight additions of LaF3 in the equimolar LiF-BaF2(1:1) base fluoride salt bath. Solubility of UO2 increased with rise in LaF3 concentration in the molten fluoride in the temperature range of 1423 K-1523 K. At a given concentration of LaF3, the UO2 solubility increased monotonously with temperature. With mixed solvent, when UF4 was added as a replacement of part of LaF3 in LiF-BaF2(1:1)-10 wt% LaF3 and LiF-BaF2(1:1)-30 wt% LaF3, there was an enhancement of solubility of UO2.

Wind effect on salt transport variability in the Bay of Bengal

NASA Astrophysics Data System (ADS)

Sandeep, K. K.; Pant, V.

2017-12-01

The Bay of Bengal (BoB) exhibits large spatial variability in sea surface salinity (SSS) pattern caused by its unique hydrological, meteorological and oceanographical characteristics. This SSS variability is largely controlled by the seasonally reversing monsoon winds and the associated currents. Further, the BoB receives substantial freshwater inputs through excess precipitation over evaporation and river discharge. Rivers like Ganges, Brahmaputra, Mahanadi, Krishna, Godavari, and Irawwady discharge annually a freshwater volume in range between 1.5 x 1012 and 1.83 x 1013 m3 into the bay. A major volume of this freshwater input to the bay occurs during the southwest monsoon (June-September) period. In the present study, a relative role of winds in the SSS variability in the bay is investigated by using an eddy-resolving three dimensional Regional Ocean Modeling System (ROMS) numerical model. The model is configured with realistic bathymetry, coastline of study region and forced with daily climatology of atmospheric variables. River discharges from the major rivers are distributed in the model grid points representing their respective geographic locations. Salt transport estimate from the model simulation for realistic case are compared with the standard reference datasets. Further, different experiments were carried out with idealized surface wind forcing representing the normal, low, high, and very high wind speed conditions in the bay while retaining the realistic daily varying directions for all the cases. The experimental simulations exhibit distinct dispersal patterns of the freshwater plume and SSS in different experiments in response to the idealized winds. Comparison of the meridional and zonal surface salt transport estimated for each experiment showed strong seasonality with varying magnitude in the bay with a maximum spatial and temporal variability in the western and northern parts of the BoB.

Liking, salt taste perception and use of table salt when consuming reduced-salt chicken stews in light of South Africa's new salt regulations.

PubMed

De Kock, H L; Zandstra, E H; Sayed, N; Wentzel-Viljoen, E

2016-01-01

This study investigated the impact of salt reduction on liking, salt taste perception, and use of table salt when consuming chicken stew in light of South Africa's new salt recommendations. In total, 432 South-African consumers (aged 35.2 ± 12.3 years) consumed a full portion of a chicken stew meal once at a central location. Four stock cube powders varying in salt content were used to prepare chicken stews: 1) no reduction - 2013 Na level; regular salt level as currently available on the South African market (24473 mg Na/100 g), 2) salt reduction smaller than 2016 level, i.e. 10%-reduced (22025 mg Na/100 g), 3) 2016 salt level, as per regulatory prescriptions (18000 mg Na/100 g), 4) 2019 salt level, as per regulatory prescriptions (13000 mg Na/100 g). Consumers were randomly allocated to consume one of the four meals. Liking, salt taste perception, and use of table salt and pepper were measured. Chicken stews prepared with reduced-salt stock powders were equally well-liked as chicken stews with the current salt level. Moreover, a gradual reduction of the salt in the chicken stews resulted in a reduced salt intake, up to an average of 19% for the total group compared to the benchmark 2013 Na level stew. However, 19% of consumers compensated by adding salt back to full compensation in some cases. More salt was added with increased reductions of salt in the meals, even to the point of full compensation. Further investigation into the impacts of nutrition communication and education about salt reduction on salt taste perception and use is needed. This research provides new consumer insights on salt use and emphasises the need for consumer-focused behaviour change approaches, in addition to reformulation of products. Copyright © 2015 Elsevier Ltd. All rights reserved.

Control of binder viscosity and hygroscopicity on particle aggregation efficiency

NASA Astrophysics Data System (ADS)

Mueller, Sebastian B.; Kueppers, Ulrich; Ayris, Paul M.; Jacob, Michael; Delmelle, Pierre; Dingwell, Donald B.

2016-04-01

In the course of explosive volcanic eruptions, large amounts of ash are released into the atmosphere and may subsequently pose a threat to infrastructure, such as aviation industry. Ash plume forecasting is therefore a crucial tool for volcanic hazard mitigation but may be significantly affected by aggregation, altering the aerodynamic properties of particles. Models struggle with the implementation of aggregation since external conditions promoting aggregation have not been completely understood; in a previous study we have shown the rapid generation of ash aggregates through liquid bonding via the use of fluidization bed technology and further defined humidity and temperature ranges necessary to trigger aggregation. Salt (NaCl) was required for the recovery of stable aggregates, acting as a cementation agent and granting aggregate cohesion. A numerical model was used to explain the physics behind particle aggregation mechanisms and further predicted a dependency of aggregation efficiency on liquid binder viscosity. In this study we proof the effect of viscosity on particle aggregation. HCl and H2SO4 solutions were diluted to various concentrations resulting in viscosities between 1 and 2 mPas. Phonolitic and rhyolitic ash samples as well as soda-lime glass beads (serving as analogue material) were fluidized in the ProCell Lab® of Glatt Ingenieurtechnik GmbH and treated with the acids via a bottom-spray technique. Chemically driven interaction between acid liquids and surfaces of the three used materials led to crystal precipitation. Salt crystals (e.g. NaCl) have been confirmed through scanning electron microscopy (SEM) and leachate analysis. Both volcanic ash samples as well as the glass beads showed a clear dependency of aggregation efficiency on viscosity of the sprayed HCl solution. Spraying H2SO4 provoked a collapse of the fluidized bed and no aggregation has been observed. This is accounted by the high hygroscopicity of H2SO4. Dissolving CaCl2 (known to be a highly hygroscopic salt) in de-ionized water yielded comparable results without observable aggregation. In case of successful aggregation, concentration of salts has been found to be in the range of published values. We conclude that non-hygroscopic salt crystal precipitation from an aqueous liquid interacting with the glass phase in volcanic ash is a very efficient way to produce cohesive ash aggregates that can survive external forces acting during transport and sedimentation.

Salt marsh and seagrass communities of Bakkhali Estuary, Cox's Bazar, Bangladesh

NASA Astrophysics Data System (ADS)

Hena, M. K. Abu; Short, F. T.; Sharifuzzaman, S. M.; Hasan, M.; Rezowan, M.; Ali, M.

2007-10-01

The species identification, distribution pattern, density and biomass of salt marsh and seagrass plants with some of the ecological parameters were studied in the Bakkhali river estuary, Cox's Bazar, Bangladesh during the first half of 2006. Two salt marsh species ( Spartina sp. and Imperata cylindrica) and one seagrass species ( Halophila beccarii) were identified during this investigation, providing the first reports of Spartina sp. and H. beccarii in coastal Bangladesh. Seagrass H. beccarii was found in an accreted area and co-existing with salt marsh, and scattered sparsely in the salt marsh habitat and macroalgae Ulva intestinalis. Flowering and fruiting were recorded from the seagrass H. beccarri during January and February. No flowers and fruits were observed for the salt marsh Spartina sp. during the study period. Results showed that the shoot density of Spartina ranged from 400 to 2875 shoots m -2 with the highest total biomass (165.80 g dry weight (DW) m -2) in March. Shoot density of H. beccarii ranged from 2716 to 14320 shoots m -2 in this estuarine coastal environment. The total biomass of seagrass was higher (17.56 g DW m -2) in March compared to the other months. The highest H. beccarii above ground (AG) biomass and below ground (BG) biomass were 9.59 g DW m -2 and 9.42 g DW m -2, respectively. These parameters are comparable with those generally observed for the salt marsh and seagrass species in the other places of the world.

ESBRI: a web server for evaluating salt bridges in proteins.

PubMed

Costantini, Susan; Colonna, Giovanni; Facchiano, Angelo M

2008-01-01

Salt bridges can play important roles in protein structure and function and have stabilizing and destabilizing effects in protein folding. ESBRI is a software available as web tool which analyses the salt bridges in a protein structure, starting from the atomic coordinates. In the case of protein complexes, the salt bridges between protein chains can be evaluated, as well as those among specific charged amino acids and the different protein subunits, in order to obtain useful information regard the protein-protein interaction. The service is available at the URL: http://bioinformatica.isa.cnr.it/ESBRI/

Consumer Knowledge, Attitudes and Salt-Related Behavior in the Middle-East: The Case of Lebanon

PubMed Central

Nasreddine, Lara; Akl, Christelle; Al-Shaar, Laila; Almedawar, Mohamad M.; Isma’eel, Hussain

2014-01-01

Sodium intake is high in Lebanon, a country of the Middle East region where rates of cardiovascular diseases are amongst the highest in the world. This study examines salt-related knowledge, attitude and self-reported behaviors amongst adult Lebanese consumers and investigates the association of socio-demographic factors, knowledge and attitudes with salt-related behaviors. Using a multicomponent questionnaire, a cross-sectional study was conducted in nine supermarkets in Beirut, based on systematic random sampling (n = 442). Factors associated with salt-related behaviors were examined by multivariate regression analysis. Specific knowledge and attitude gaps were documented with only 22.6% of participants identifying processed foods as the main source of salt, 55.6% discerning the relationship between salt and sodium, 32.4% recognizing the daily limit of salt intake and 44.7% reporting being concerned about the amount of salt in their diet. The majority of participants reported behavioral practices that increase salt intake with only 38.3% checking for salt label content, 43.7% reporting that their food purchases are influenced by salt content and 38.6% trying to buy low-salt foods. Knowledge, attitudes and older age were found to significantly predict salt-related behaviors. Findings offer valuable insight on salt-related knowledge, attitude and behaviors in a sample of Lebanese consumers and provide key information that could spur the development of evidence-based salt-reduction interventions specific to the Middle East. PMID:25401502

Regression Analysis to Identify Factors Associated with Household Salt Iodine Content at the Sub-National Level in Bangladesh, India, Ghana and Senegal

PubMed Central

Knowles, Jacky; Kupka, Roland; Dumble, Sam; Garrett, Greg S.; Pandav, Chandrakant S.; Yadav, Kapil; Nahar, Baitun; Touré, Ndeye Khady; Amoaful, Esi Foriwa; Gorstein, Jonathan

2018-01-01

Regression analyses of data from stratified, cluster sample, household iodine surveys in Bangladesh, India, Ghana and Senegal were conducted to identify factors associated with household access to adequately iodised salt. For all countries, in single variable analyses, household salt iodine was significantly different (p < 0.05) between strata (geographic areas with representative data, defined by survey design), and significantly higher (p < 0.05) among households: with better living standard scores, where the respondent knew about iodised salt and/or looked for iodised salt at purchase, using salt bought in a sealed package, or using refined grain salt. Other country-level associations were also found. Multiple variable analyses showed a significant association between salt iodine and strata (p < 0.001) in India, Ghana and Senegal and that salt grain type was significantly associated with estimated iodine content in all countries (p < 0.001). Salt iodine relative to the reference (coarse salt) ranged from 1.3 (95% CI 1.2, 1.5) times higher for fine salt in Senegal to 3.6 (95% CI 2.6, 4.9) times higher for washed and 6.5 (95% CI 4.9, 8.8) times higher for refined salt in India. Sub-national data are required to monitor equity of access to adequately iodised salt. Improving household access to refined iodised salt in sealed packaging, would improve iodine intake from household salt in all four countries in this analysis, particularly in areas where there is significant small-scale salt production. PMID:29671774

Arylsulfatase Activity in Salt Marsh Soils †

PubMed Central

Oshrain, R. L.; Wiebe, W. J.

1979-01-01

The presence of arylsulfatase(s) was confirmed in salt marsh soils. The temperatures of maximum activity and inactivation, the pH range over which the enzyme was active, and the Km values were similar to those of soil enzymes. Unlike soil arylsulfatases, however, the salt marsh enzymes do not appear to be repressed by sulfate. It is postulated that these enzymes may be necessary for the initiation of arylsulfate ester metabolism. PMID:16345425

From cerebral salt wasting to diabetes insipidus with adipsia: case report of a child with craniopharyngioma.

PubMed

Raghunathan, Veena; Dhaliwal, Maninder Singh; Gupta, Aditya; Jevalikar, Ganesh

2015-03-01

Craniopharyngioma is associated with a wide and interesting variety of sodium states both by itself and following surgical resection. These are often challenging to diagnose, especially given their dynamic nature during the perioperative course. We present the case of a boy with craniopharyngioma who had hyponatremia due to cerebral salt wasting preoperatively, developed diabetes insipidus (DI) intraoperatively and proceeded to develop hypernatremia with adipsic DI. Cerebral salt wasting is a rare presenting feature of craniopharyngioma. Postoperative DI can be associated with thirst abnormalities including adipsia due to hypothalamic damage; careful monitoring and a high index of suspicion are required for its detection. Adipsic DI is a difficult condition to manage; hence a conservative surgical approach is suggested.

A Study of Novel Hexavalent Phosphazene Salts as Draw Solutes in Forward Osmosis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mark L. Stone; Aaron D. Wilson; Mason K. Harrup

2013-03-01

Two novel multi-valent salts based on phosphazene chemistry have been synthesized and characterized as forward osmosis (FO) draw solutes. Commercially obtained hexachlorocyclotriphosphazene was reacted with the sodium salt of 4-ethylhydroxybenzoate to yield hexa(4-ethylcarboxylatophenoxy)phosphazene. Hydrolysis, followed by and neutralization with NaOH or LiOH, of the resulting acidic moieties yielded water soluble sodium and lithium phosphazene salts, respectively. Degrees of dissociation were determined through osmometry over the range of 0.05-0.5 m, giving degrees of 3.08-4.95 per mole, suggesting a high osmotic potential. The Li salt was found to be more ionized in solution than the sodium salt, and this was reflected inmore » FO experiments where the Li salt gave higher initial fluxes (~ 7 L/m2h) as compared to the sodium salt (~6 L/m2h) at identical 0.07 m draw solution concentrations at 30 °C. Longer term experiments revealed no detectable degradation of the salts; however some hydrolysis of the cellulose acetate membrane was observed, presumably due to the pH of the phosphazene salt draw solution (pH = ~8).« less

Important Learnings for Reliable Management of Hydrocarbon Production and Salt Solution Mining induced Subsidence from Case Histories in the Netherlands

NASA Astrophysics Data System (ADS)

Waal, H. D.; Muntendam-Bos, A.; Breunese, J.; Roest, H.; Fokker, P. A.

2012-12-01

Reliable management of subsidence caused by hydrocarbon production and salt solution mining is important for a country like the Netherlands where most land surface is below or near sea level. However, a factor two difference between prediction and observation is not uncommon. To nevertheless ensure a high probability that subsidence is kept within the limits an area can robustly sustain, a tightly integrated prediction/monitoring/updating loop is applied. Prior to production, scenario's spanning the range of parameter and model uncertainties are generated to calculate possible subsidence outcomes. The probability of each scenario is updated over time through confrontation with measurements (e.g. using Bayesian statistics) as they become available. Production can thus be halted or adjusted timely if probabilities start to indicate an unacceptable risk of exceeding set limits now or in the future. A number of projects with well documented, high quality prediction and monitoring were started in the Netherlands in the second half of the previous century. They provide quality case histories covering multi-decade production periods from which important learnings have been been extracted. Firstly, from the data it is clear that sandstone reservoir compaction is not a linear function of pressure depletion. Initially the rock in the field compacts much less than expected based on standard lab measurements. As pressure drops further, compaction gradually increases, reaching and exceeding lab values. Various mechanisms could be responsible: delayed compaction in lower permeability/poorly connected parts of the reservoir or aquifers; intrinsic non-linear, time-dependent, rate-type or diffusive behavior of the reservoir rock; previous deeper burial or increasing overpressure over geological time. The observed field behavior is described reasonably well by a single exponential time decay model. The non-linear and/or time-dependent field behavior has to be accounted for when updating predictions based on early field data. Otherwise it leads to under-prediction of subsidence, followed by multiple upward adjustments as new data become available. Secondly, the large difference between lab and field loading rate results in late time field compressibilities that can be 20 to 30% higher then the lab data. For chalk reservoirs the difference in loading rate causes much earlier pore collapse in the field. These effects need and can be accounted for. Thirdly, the case histories show that the shape of the subsidence bowl changes over time. The bowl shape becomes steeper in time for hydrocarbon extraction and flatter in the case of salt extraction. This is believed to be related to the changing elasticity contrast between the compacting volume and its surroundings as the reservoir compressibility increases and surrounding salt layers start to creep. The observed shape changes can be modeled numerically or by a varying rigid basement depth in the analytical van Opstal model. Not accounting for it can result in large subsidence allocation errors where salt mining and hydrocarbon production bowls overlap.

Structures and interactions among globular proteins above the isoelectric point in the presence of divalent ions: A small angle neutron scattering and dynamic light scattering study

NASA Astrophysics Data System (ADS)

Kundu, Sarathi; Pandit, Subhankar; Abbas, Sohrab; Aswal, V. K.; Kohlbrecher, J.

2018-02-01

Small angle neutron scattering study reveals that at pD ≈ 7.0, above the isoelectric point of the globular protein Bovine Serum Albumin (BSA), in the presence of different divalent ions (Mg2+, Ca2+, Sr2+ and Ba2+), the short-range attractive interaction remains nearly constant and the intermediate-range repulsive interaction decreases with increasing salt concentration up to a certain concentration value but after that remains unchanged. However, for the monovalent ion (Na+), repulsive interaction decreases gradually up to 1 M salt concentration. Dynamic light scattering study shows that for all ions, diffusion coefficient of BSA decreases with increasing salt concentration and then nearly saturates.

[Spatial heterogeneity of soil salinization and its influencing factors in the typical region of the Mu Us Desert-Loess Plateau transitional zone, Northwest China].

PubMed

Zhao, Xuan; Hao, Qi Li; Sun, Ying Ying

2017-06-18

Studies on the spatial heterogeneity of saline soil in the Mu Us Desert-Loess Plateau transition zone are meaningful for understanding the mechanisms of land desertification. Taking the Mu Us Desert-Loess Plateau transition zone as the study subject, its spatial heterogeneity of pH, electrical conductivity (EC) and total salt content were analyzed by using on-site sampling followed with indoor analysis, classical statistical and geostatistical analysis. The results indicated that: 1) The average values of pH, EC and total salt content were 8.44, 5.13 mS·cm -1 and 21.66 g·kg -1 , respectively, and the coefficient of variation ranged from 6.9% to 73.3%. The pH was weakly variable, while EC and total salt content were moderately variable. 2) Results of semivariogram analysis showed that the most fitting model for spatial variability of all three indexes was spherical model. The C 0 /(C 0 +C) ratios of three indexes ranged from 8.6% to 14.3%, which suggested the spatial variability of all indexes had a strong spatial autocorrelation, and the structural factors played a more important role. The variation range decreased in order of pH

The epidemiology of hypernatraemia in hospitalised children in Lothian: a 10-year study showing differences between dehydration, osmoregulatory dysfunction and salt poisoning.

PubMed

Forman, Sarah; Crofton, Patricia; Huang, Hian; Marshall, Tom; Fares, Katia; McIntosh, Neil

2012-06-01

The relative frequencies of the causes of hypernatraemia in children after the neonatal period are unknown. Salt poisoning and osmoregulatory dysfunction are extremely rare and potentially fatal. In this retrospective 10-year study, the incidence, causes and differential biochemistry of hypernatraemia in children is examined. Children with hypernatraemia (sodium ≥ 150 mmol/litre) aged >2 weeks to 17 years were identified from laboratory data of two paediatric departments serving the Lothian region of Scotland. A review of patient notes established time of onset and cause. Denominator data were available from the Scottish Health Service. On admission to hospital, 1 in 2288 children (1:1535 admitted as an emergency) had hypernatraemia. This is 1 in 30 563 Lothian children <17 years. Overall 0.04% hospital stays had an episode of hypernatraemia. In 45 children admitted with 64 separate episodes (11 from a case of salt poisoning), the commonest cause was dehydration secondary to either gastroenteritis or systemic infection; 31% had an underlying chronic neurological disorder. A total of 177 further cases developed hypernatraemia after admission. The commonest causes were dehydration secondary to severe systemic infection and postoperative cardiac surgery. Urine sodium:creatinine ratio and fractional excretion of sodium were both much higher in the salt poisoning case than in a child with osmoregulatory dysfunction or children with simple dehydration. Hypernatraemia after 2 weeks of age is uncommon, and on admission is usually associated with dehydration. Salt poisoning and osmoregulatory dysfunction are rare but should be considered in cases of repeated hypernatraemia without obvious cause. Routine measurement of urea, creatinine and electrolytes on paired urine and plasma on admission will differentiate these rare causes.

Selective catalysts and their preparation for catalytic hydrocarbon synthesis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Iglesia, E.; Vroman, H.; Soled, S.

1991-07-30

This patent describes a method for preparing a supported cobalt catalyst particle. It comprises contacting a support particle with a molten cobalt salt, for a period sufficient to impregnate substantially all of the molten cobalt salt on the support to a depth of less than about 200 {mu}m; drying the supported cobalt salt obtained; reducing the cobalt of the supported cobalt salt to metallic cobalt by heating the salt in the presence of H{sub 2}, wherein the heating is conducted at a rate of less than about 1{degrees} C./min. up to a maximum temperature ranging from about 100{degrees} C. tomore » about 500{degrees} C., to produce a supported cobalt catalyst particle.« less

Salt tolerance research in date palm tree (Phoenix dactylifera L.), past, present, and future perspectives.

PubMed

Yaish, Mahmoud W; Kumar, Prakash P

2015-01-01

The date palm can adapt to extreme drought, to heat, and to relatively high levels of soil salinity. However, excessive amounts of salt due to irrigation with brackish water lead to a significant reduction in the productivity of the fruits as well as marked decrease in the viable numbers of the date palm trees. It is imperative that the nature of the existing salt-adaptation mechanism be understood in order to develop future date palm varieties that can tolerate excessive soil salinity. In this perspective article, several research strategies, obstacles, and precautions are discussed in light of recent advancements accomplished in this field and the properties of this species. In addition to a physiological characterization, we propose the use of a full range of OMICS technologies, coupled with reverse genetics approaches, aimed toward understanding the salt-adaption mechanism in the date palm. Information generated by these analyses should highlight transcriptional and posttranscriptional modifications controlling the salt-adaptation mechanisms. As an extremophile with a natural tolerance for a wide range of abiotic stresses, the date palm may represent a treasure trove of novel genetic resources for salinity tolerance.

Effect of crude glycerol-derived inhibitors on ethanol production by Enterobacter aerogenes.

PubMed

Lee, Sang Jun; Kim, Sung Bong; Kang, Seong Woo; Han, Sung Ok; Park, Chulhwan; Kim, Seung Wook

2012-01-01

In this study, ethanol production from pure and crude glycerol using Enterobacter aerogenes ATCC 29007 was evaluated under anaerobic culture conditions. Inhibitory effects of substrate concentrations, pH, and salt concentrations were investigated based on crude glycerol components. Ethanol production was performed with pure glycerol concentrations ranging from 5 to 30 g/L to evaluate the effects of substrate concentration and osmotic pressure. The consumed glycerol was 5-14.33 g/L, and the yield of ethanol was higher than 0.75 mol ethanol/mol glycerol after 24 h of cultivation. To evaluate the inhibitory effects of salts (NaCl and KCl), experiments were performed with 0-20 g/L of each salt. Inhibitory effects of salts were strongest at high salt concentrations. The inhibitory effect of pH was performed in the pH range 4-10, and cell growth and ethanol production were highest at pH 5-6. Also, ethanol production was slightly inhibited at low concentration of crude glycerol comparison with pure glycerol. However, significant inhibitory effects were not observed at 1.5 and 2% crude glycerol which showed higher ethanol production compared to pure glycerol.

Finite Element Modeling of In-Situ Stresses near Salt Bodies

NASA Astrophysics Data System (ADS)

Sanz, P.; Gray, G.; Albertz, M.

2011-12-01

The in-situ stress field is modified around salt bodies because salt rock has no ability to sustain shear stresses. A reliable prediction of stresses near salt is important for planning safe and economic drilling programs. A better understanding of in-situ stresses before drilling can be achieved using finite element models that account for the creeping salt behavior and the elastoplastic response of the surrounding sediments. Two different geomechanical modeling techniques can be distinguished: "dynamic" modeling and "static" modeling. "Dynamic" models, also known as forward models, simulate the development of structural processes in geologic time. This technique provides the evolution of stresses and so it is used to simulate the initiation and development of structural features, such as, faults, folds, fractures, and salt diapers. The original or initial configuration and the unknown final configuration of forward models are usually significantly different therefore geometric non-linearities need to be considered. These models may be difficult to constrain when different tectonic, deposition, and erosion events, and the timing among them, needs to be accounted for. While dynamic models provide insight into the stress evolution, in many cases is very challenging, if not impossible, to forward model a configuration to its known present-day geometry; particularly in the case of salt layers that evolve into highly irregular and complex geometries. Alternatively, "static" models use the present-day geometry and present-day far-field stresses to estimate the present-day in-situ stress field inside a domain. In this case, it is appropriate to use a small deformation approach because initial and final configurations should be very similar, and more important, because the equilibrium of stresses should be stated in the present-day initial configuration. The initial stresses and the applied boundary conditions are constrained by the geologic setting and available data. This modeling technique does not predict the evolution of structural elements or stresses with time; therefore it does not provide any insight into the formation of fractures that were previously developed under a different stress condition or the development of overpressure generated by a high sedimentation rate. This work provides a validation for predicting in-situ stresses near salt using "static" models. We compare synthetic examples using both modeling techniques and show that stresses near salt predicted with "static" models are comparable to the ones generated by "dynamic" models.

40 CFR 471.33 - New source performance standards (NSPS).

Code of Federal Regulations, 2013 CFR

2013-07-01

... the range of 7.5 to 10.0 at all times. (w) Molten salt rinse. Subpart C—NSPS Pollutant or pollutant... nickel-cobalt treated with molten salt Chromium 0.312 0.127 Nickel 0.464 0.312 Fluoride 50.2 22.3 Oil and...

40 CFR 471.33 - New source performance standards (NSPS).

Code of Federal Regulations, 2012 CFR

2012-07-01

... the range of 7.5 to 10.0 at all times. (w) Molten salt rinse. Subpart C—NSPS Pollutant or pollutant... nickel-cobalt treated with molten salt Chromium 0.312 0.127 Nickel 0.464 0.312 Fluoride 50.2 22.3 Oil and...

40 CFR 471.33 - New source performance standards (NSPS).

Code of Federal Regulations, 2014 CFR

2014-07-01

... the range of 7.5 to 10.0 at all times. (w) Molten salt rinse. Subpart C—NSPS Pollutant or pollutant... nickel-cobalt treated with molten salt Chromium 0.312 0.127 Nickel 0.464 0.312 Fluoride 50.2 22.3 Oil and...

Fluoride salts and container materials for thermal energy storage applications in the temperature range 973 to 1400 K

NASA Technical Reports Server (NTRS)

Misra, Ajay K.; Whittenberger, J. Daniel

1987-01-01

Multicomponent fluoride salt mixtures were characterized for use as latent heat of fusion heat storage materials in advanced solar dynamic space power systems with operating temperatures in the range of 973 to 1400 K. The melting points and eutectic composition for many systems with published phase diagrams were verified, and several new eutectic compositions were identified. Additionally, the heats of fusion of several binary and ternary eutectics and congruently melting intermediate compounds were measured by differential scanning calorimetry. The extent of corrosion of various metals by fluoride melts was estimated from thermodynamic considerations, and equilibrium conditions inside a containment vessel were calculated as functions of the initial moisture content of the salt and free volume above the molten salt. Preliminary experimental data on the corrosion of commercial, high-temperature alloys in LiF-19.5CaF2 and NaF-27CaF2-36MgF2 melts are presented and compared to the thermodynamic predictions.

Fluoride salts and container materials for thermal energy storage applications in the temperature range 973 - 1400 K

NASA Technical Reports Server (NTRS)

Misra, Ajay K.; Whittenberger, J. Daniel

1987-01-01

Multicomponent fluoride salt mixtures were characterized for use as latent heat of fusion heat storage materials in advanced solar dynamic space power systems with operating temperatures in the range of 973 to 1400 K. The melting points and eutectic composition for many systems with published phase diagrams were verified, and several new eutectic compositions were identified. Additionally, the heats of fusion of several binary and ternary eutectics and congruently melting intermediate compounds were measured by differential scanning calorimetry. The extent of corrosion of various metals by fluoride melts was estimated from thermodynamic considerations, and equilibrium conditions inside a containment vessel were calculated as functions of the initial moisture content of the salt and free volume above the molten salt. Preliminary experimental data on the corrosion of commercial, high-temperature alloys in LiF-19.5CaF2 and NaF-27CaF2-36MgF2 melts are presented and compared to the thermodynamic predictions.

Salt as a public health challenge in continental European convenience and ready meals.

PubMed

Kanzler, Sonja; Hartmann, Christina; Gruber, Anita; Lammer, Guido; Wagner, Karl-Heinz

2014-11-01

To assess the salt content of continental European convenience and ready meals. A multistage study in which, after laboratory analysis of the products' salt contents (n 32), new salt-reduced meals were developed through food reformulation. Additionally, a comprehensive survey of convenience meals from the Austrian market (n 572) was conducted to evaluate the salt contents of a wider product range. Six continental European countries participated. No subjects enrolled. The salt contents of continental European convenience and ready meals mostly exceeded 1·8 g/100 g, which is 30 % of the targeted daily intake level; some contained even more than the recommended daily intake of 6 g. The highest salt contents were found in pizzas and pasta dishes, the lowest ones in sweet meals. Large variations in salt levels were found not only between and within meal type categories, but also between similar meals from different producers. In addition, our approach to develop new salt-reduced meals showed that a stepwise reduction of the ready meals' salt contents is possible without compromising the sensory quality. To address the problem of hypertension and increased risk for CVD through high salt intake, a reduction of the salt levels in continental European convenience and ready meals is urgently needed, since they are providing a major part of the daily salt intake. Successful national-wide salt reduction strategies in the UK or Finland have already demonstrated the public health impact of this setting.

Continuous production of granular or powder Ti, Zr and Hf or their alloy products

DOEpatents

White, Jack C.; Oden, Laurance L.

1993-01-01

A continuous process for producing a granular metal selected from the group consisting of Ti, Zr or Hf under conditions that provide orderly growth of the metal free of halide inclusions comprising: a) dissolving a reducing metal selected from the group consisting of Na, Mg, Li or K in their respective halide salts to produce a reducing molten salt stream; b) preparing a second molten salt stream containing the halide salt of Ti, Zr or Hf; c) mixing and reacting the two molten streams of steps a) and b) in a continuous stirred tank reactor; d) wherein steps a) through c) are conducted at a temperature range of from about 800.degree. C. to about 1100.degree. C. so that a weight percent of equilibrium solubility of the reducing metal in its respective halide salt varies from about 1.6 weight percent at about 900.degree. C. to about 14.4 weight percent at about 1062.degree. C.; and wherein a range of concentration of the halide salt of Ti, Zn or Hf in molten halides of Na, Mg, Li or K is from about 1 to about 5 times the concentration of Na, Mg, Li or K; e) placing the reacted molten stream from step c) in a solid-liquid separator to recover an impure granular metal product by decantation, centrifugation, or filtration; and f) removing residual halide salt impurity by vacuum evaporator or inert gas sweep at temperatures from about 850.degree. C. to 1000.degree. C. or cooling the impure granular metal product to ambient temperature and water leaching off the residual metal halide salt.

Cross-sectional study of the association of abomasal displacement or volvulus with serum electrolyte and mineral concentrations in dairy cows.

PubMed Central

Delgado-Lecaroz, R; Warnick, L D; Guard, C L; Smith, M C; Barry, D A

2000-01-01

The objective of this study was to evaluate serum mineral and electrolyte concentrations at the time of on-farm diagnosis of left displaced abomasum, right displaced abomasum, or abomasal volvulus in dairy cows. Data were collected from 104 affected cows and 96 control cows matched with cases, based on herd, parity, and stage of lactation. Cows with abomasal displacement or volvulus had significantly lower calcium, phosphorous, magnesium, potassium, and chloride concentrations and increased anion gap at the time of diagnosis compared with control cows from the same herds. The percentages of cases and controls with total serum calcium concentrations below the lower limit of the laboratory reference range (2.08 mmol/L [8.3 mg/dL]) were 70% and 23%, respectively. Based on the large percentage of cases with hypocalcemia, administering calcium salts at the time of treatment of field cases of abomasal displacement or volvulus may be beneficial. PMID:10769767

The Composition and Physical Properties of Chloride Salt-bearing Deposits on Mars

NASA Astrophysics Data System (ADS)

Glotch, T. D.; Bandfield, J.; Wolff, M. J.; Arnold, J. A.; Che, C.

2015-12-01

Anhydrous chloride salt deposits were first discovered on Mars by the 2001 Odyssey Thermal Emission Imaging System (THEMIS) and have been further characterized by Mars Reconnaissance Orbiter CRISM and Mars Express visible/near-IR (VNIR) hyperspectral imaging spectrometers. At mid-IR wavelengths, the salt-bearing deposits display a blue slope superimposed on the regional regolith spectral shape. At VNIR wavelengths, ratio spectra display a featureless red slope between 1.0 and 2.5 μm and a reduced 3 μm band, indicating that the deposits are desiccated compared to the surrounding terrain. In this work, we compare laboratory and model spectra to THEMIS spectra to evaluate the abundance and physical properties of salt in these deposits. We acquired mid-IR emissivity spectra of a suite of halite/basalt mixtures separated to <10 μm, 63-90 μm, 125-180 μm, and 250-355 μm. Halite concentrations for each size separate ranged from 1-75%. Laboratory spectra of the coarsest particulates do not adequately reproduce the spectral shapes associated with any of the Martian salt deposits. The finest particulates display spectral characteristics associated with salt deposits found in high albedo, dusty regions of Mars, and those in the middle size ranges are consistent with the spectra of most Martian salt deposits and suggest abundances between 10 and 25 wt.% salt. The increase in salt content from ~10-25% coincides with a shift in the THEMIS emissivity maximum from band 3 to band 4, suggesting this can be used as a rough indicator of salt content in remote sensing studies. We also used a hybrid T-matrix/Hapke light scattering model to model the scattering properties and mid-IR spectra of clusters of salt/silicate spheres. The model results show that as halite content is increased, the transparency of the cluster increases substantially, resulting in multiple internal scattering, and substantially reduced emissivity, consistent with the THEMIS data and laboratory spectra. Phase function changes associated with increased halite abundance result in the cluster being slightly less forward scattering, which also contributes to the observed spectral changes.

Systematic interpolation method predicts protein chromatographic elution with salt gradients, pH gradients and combined salt/pH gradients.

PubMed

Creasy, Arch; Barker, Gregory; Carta, Giorgio

2017-03-01

A methodology is presented to predict protein elution behavior from an ion exchange column using both individual or combined pH and salt gradients based on high-throughput batch isotherm data. The buffer compositions are first optimized to generate linear pH gradients from pH 5.5 to 7 with defined concentrations of sodium chloride. Next, high-throughput batch isotherm data are collected for a monoclonal antibody on the cation exchange resin POROS XS over a range of protein concentrations, salt concentrations, and solution pH. Finally, a previously developed empirical interpolation (EI) method is extended to describe protein binding as a function of the protein and salt concentration and solution pH without using an explicit isotherm model. The interpolated isotherm data are then used with a lumped kinetic model to predict the protein elution behavior. Experimental results obtained for laboratory scale columns show excellent agreement with the predicted elution curves for both individual or combined pH and salt gradients at protein loads up to 45 mg/mL of column. Numerical studies show that the model predictions are robust as long as the isotherm data cover the range of mobile phase compositions where the protein actually elutes from the column. Copyright © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Theory and applications of a novel ion exchange chromatographic technology using controlled pH gradients for separating proteins on anionic and cationic stationary phases.

PubMed

Tsonev, Latchezar I; Hirsh, Allen G

2008-07-25

pISep is a major new advance in low ionic strength ion exchange chromatography. It enables the formation of externally controlled pH gradients over the very broad pH range from 2 to 12. The gradients can be generated on either cationic or anionic exchangers over arbitrary pH ranges wherein the stationary phases remain totally charged. Associated pISep software makes possible the calculation of either linear, nonlinear or combined, multi-step, multi-slope pH gradients. These highly reproducible pH gradients, while separating proteins and glycoproteins in the order of their electrophoretic pIs, provide superior chromatographic resolution compared to salt. This paper also presents a statistical mechanical model for protein binding to ion exchange stationary phases enhancing the electrostatic interaction theory for the general dependence of retention factor k, on both salt and pH simultaneously. It is shown that the retention factors computed from short time isocratic salt elution data of a model protein can be used to accurately predict its salt elution concentration in varying slope salt elution gradients formed at varying isocratic pH as well as the pH at which it will be eluted from an anionic exchange column by a pISep pH gradient in the absence of salt.

Understanding the Differences Between Cocrystal and Salt Aqueous Solubilities.

PubMed

Cavanagh, Katie L; Maheshwari, Chinmay; Rodríguez-Hornedo, Naír

2018-01-01

This work challenges the popular notion that pharmaceutical salts are more soluble than cocrystals. There are cocrystals that are more soluble than salt forms of a drug and vice-versa. It all depends on the interplay between the chemistry of both the solid and solution phases. Aqueous solubility, pH max , and supersaturation index (SA = S CC /S D or S salt /S D ) of cocrystals and salts of a basic drug, lamotrigine (LTG), were determined, and mathematical models that predict the influence of cocrystal/salt K sp and K a were derived. K sp and SA followed the order LTG-nicotinamide cocrystal (18) > LTG-HCl salt (12) > LTG-saccharin salt (5) > LTG-methylparaben cocrystal (1) > LTG-phenobarbital cocrystal (0.2). The values in parenthesis represent SA under nonionizing conditions. Cocrystal/salt solubility and thermodynamic stability are determined by pH and will drastically change with a single unit change in pH. pH max values ranged from 5.0 (saccharin salt) to 6.4 (methylparaben cocrystal) to 9.0 (phenobarbital cocrystal). Cocrystal/salt pH max dependence on pK sp and pK a shows that cocrystals and salts exhibit different behavior. Solubility and pH max are as important as supersaturation index in assessing the stability and risks associated with conversions of supersaturating forms. Copyright © 2018 American Pharmacists Association®. Published by Elsevier Inc. All rights reserved.

Reconsolidated Salt as a Geotechnical Barrier

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hansen, Francis D.; Gadbury, Casey

Salt as a geologic medium has several attributes favorable to long-term isolation of waste placed in mined openings. Salt formations are largely impermeable and induced fractures heal as stress returns to equilibrium. Permanent isolation also depends upon the ability to construct geotechnical barriers that achieve nearly the same high-performance characteristics attributed to the native salt formation. Salt repository seal concepts often include elements of reconstituted granular salt. As a specific case in point, the Waste Isolation Pilot Plant recently received regulatory approval to change the disposal panel closure design from an engineered barrier constructed of a salt-based concrete to onemore » that employs simple run-of-mine salt and temporary bulkheads for isolation from ventilation. The Waste Isolation Pilot Plant is a radioactive waste disposal repository for defense-related transuranic elements mined from the Permian evaporite salt beds in southeast New Mexico. Its approved shaft seal design incorporates barrier components comprising salt-based concrete, bentonite, and substantial depths of crushed salt compacted to enhance reconsolidation. This paper will focus on crushed salt behavior when applied as drift closures to isolate disposal rooms during operations. Scientific aspects of salt reconsolidation have been studied extensively. The technical basis for geotechnical barrier performance has been strengthened by recent experimental findings and analogue comparisons. The panel closure change was accompanied by recognition that granular salt will return to a physical state similar to the halite surrounding it. Use of run-of-mine salt ensures physical and chemical compatibility with the repository environment and simplifies ongoing disposal operations. Our current knowledge and expected outcome of research can be assimilated with lessons learned to put forward designs and operational concepts for the next generation of salt repositories. Mined salt repositories have the potential to isolate permanently vast inventories of radioactive and hazardous wastes.« less

[Botulism in Osterdalen in 1831].

PubMed

Schjønsby, Hans Petter

2002-12-10

The earliest report we have had of an outbreak of botulism in Norway is from 1934, of five cases caused by contaminated salted and dried ham. All patients survived. This paper describes an early outbreak of botulism in the county of Hedmark in 1831 on the basis of a previously unknown report to the county governor from district public health officer Peter Heiberg (1778-1849). Two cases were reported, one of them fatal. The contaminated food was salted and fermented trout or char.

Landslides Monitoring on Salt Deposits Using Geophysical Methods, Case study - Slanic Prahova, Romania

NASA Astrophysics Data System (ADS)

Ovidiu, Avram; Rusu, Emil; Maftei, Raluca-Mihaela; Ulmeanu, Antonio; Scutelnicu, Ioan; Filipciuc, Constantina; Tudor, Elena

2017-12-01

Electrometry is most frequently applied geophysical method to examine dynamical phenomena related to the massive salt presence due to resistivity contrasts between salt, salt breccia and geological covering formations. On the vertical resistivity sections obtained with VES devices these three compartments are clearly differentiates by high resistivity for the massive salt, very low for salt breccia and variable for geological covering formations. When the land surface is inclined, shallow formations are moving gravitationally on the salt back, producing a landslide. Landslide monitoring involves repeated periodically measurements of geoelectrical profiles into a grid covering the slippery surface, in the same conditions (climate, electrodes position, instrument and measurement parameters). The purpose of monitoring landslides in Slanic Prahova area, was to detect the changes in resistivity distribution profiles to superior part of subsoil measured in 2014 and 2015. Measurement grid include several representative cross sections in susceptibility to landslides point of view. The results are graphically represented by changing the distribution of topography and resistivity differences between the two sets of geophysical measurements.

Seasonal variation of fractionated sea-salt particles on the Antarctic coast

NASA Astrophysics Data System (ADS)

Hara, K.; Osada, K.; Yabuki, M.; Yamanouchi, T.

2012-09-01

Aerosol sampling was conducted at Syowa Station, Antarctica (coastal station) in 2004-2006. SO42-depletion by mirabilite precipitation was identified from April through November. The fractionated sea-salt particles were distributed in ultrafine- coarse modes. Molar ratios of Mg2+/Na+ and K+/Na+ were higher than in bulk seawater ratio during winter-spring. The Mg2+/Na+ ratio in aerosols greatly exceeded the upper limit in the case only with mirabilite precipitation. The temperature dependence of Mg2+/Na+ ratio strongly suggested that higher ratios of Mg2+/Na+ and K+/Na+ were associated with sea-salt fractionation by precipitation of mirabilite at -9°C, hydrohalite at ca. -23°C and other salts such as ikaite at ca. -5°C and gypsum at ca. -22°C during winter-spring. Mg-salts with lower deliquescence relative humidity can be enriched gradually in the fractionated sea-salt particles. Results suggests that sea-salt fractionation can alter aerosol hygroscopicity and atmospheric chemistry in polar regions.

Thermal Properties of Consolidated Granular Salt as a Backfill Material

NASA Astrophysics Data System (ADS)

Paneru, Laxmi P.; Bauer, Stephen J.; Stormont, John C.

2018-03-01

Granular salt has been proposed as backfill material in drifts and shafts of a nuclear waste disposal facility where it will serve to conduct heat away from the waste to the host rock. Creep closure of excavations in rock salt will consolidate (reduce the porosity of) the granular salt. This study involved measuring the thermal conductivity and specific heat of granular salt as a function of porosity and temperature to aid in understanding how thermal properties will change during granular salt consolidation accomplished at pressures and temperatures consistent with a nuclear waste disposal facility. Thermal properties of samples from laboratory-consolidated granular salt and in situ consolidated granular salt were measured using a transient plane source method at temperatures ranging from 50 to 250 °C. Additional measurements were taken on a single crystal of halite and dilated polycrystalline rock salt. Thermal conductivity of granular salt decreased with increases in temperature and porosity. Specific heat of granular salt at lower temperatures decreased with increasing porosity. At higher temperatures, porosity dependence was not apparent. The thermal conductivity and specific heat data were fit to empirical models and compared with results presented in the literature. At comparable densities, the thermal conductivities of granular salt samples consolidated hydrostatically in this study were greater than those measured previously on samples formed by quasi-static pressing. Petrographic studies of the consolidated salt indicate that the consolidation method influenced the nature of the porosity; these observations are used to explain the variation of measured thermal conductivities between the two consolidation methods. Thermal conductivity of dilated polycrystalline salt was lower than consolidated salt at comparable porosities. The pervasive crack network along grain boundaries in dilated salt impedes heat flow and results in a lower thermal conductivity compared to hydrostatically consolidated salt.

1-Amine-1,2,3-triazolium salts with oxidizing anions: A new family of energetic materials with good performance

NASA Astrophysics Data System (ADS)

Zhang, Zhi-Bin; Zhang, Jian-Guo

2018-04-01

A series of 1-amino-1,2,3-triazole (ATZ) based energetic nitrogen-rich salts are prepared by using acid-base neutralization reaction (1:1 M ratio), and fully characterized. Structures of the salts are recrystallized and determined by single-crystal X-ray diffraction, which dominated by a strong hydrogen-bond influence with the densities ranging from 1.692 to 1.868 g cm-3. Thermal behaviors have characterized by using the DSC and TG-DTG technologies. The enthalpies of formation have calculated by using Gaussian 03. The detonation parameters of the salts are determined by using the K-J method, and most salts show promising detonation performances (D: 6699-8231 m s-1, P: 19.2-30.7 GPa), among which the salt of 1-amino-1,2,3-triazolium trinitrophloroglucinate has a detonation properties comparable to RDX. The sensitivities results provided the salts as insensitive energetic materials.

Intelligent transportation systems at the 2002 Salt Lake City Olympic Games : traffic management and traveler information case study

DOT National Transportation Integrated Search

2003-04-01

Utah Department of Transportation (UDOT) contracted for a series of evaluation efforts associated with the development, deployment, and operation of their Intelligent Transportation Systems (ITS) in the Salt Lake City Region, which are known as the C...

Single mode, short cavity, Pb-salt diode lasers operating in the 5, 10, and 30-microns spectral regions

NASA Technical Reports Server (NTRS)

Linden, K. J.

1985-01-01

Pb-salt diode lasers are being used as frequency-tunable infrared sources in high resolution spectroscopy and heterodyne detection applications. Recent advances in short cavity, stripe-geometry laser configurations have led to significant increases in maximum CW operating temperature, single mode operation, and increased single mode tuning range. This paper describes short cavity, stripe geometry lasers operating in the 5, 10, and 30-microns spectral regions, with single mode tuning ranges of over 6/cm.

SIZE DISTRIBUTION OF SEA-SALT EMISSIONS AS A FUNCTION OF RELATIVE HUMIDITY

EPA Science Inventory

This note presents a straightforward method to correct sea-salt-emission particle-size distributions according to local relative humidity. The proposed method covers a wide range of relative humidity (0.45 to 0.99) and its derivation incorporates recent laboratory results on sea-...

40 CFR 471.53 - New source performance standards (NSPS).

Code of Federal Regulations, 2014 CFR

2014-07-01

... TSS 123 97.9 pH (1) (1) 1 Within the range of 7.5 to 10.0 at all times. (p) Molten salt rinse. Subpart... (pounds per million off-pounds) of refractory metals treated with molten salt Copper 0.810 0.386 Nickel 0...

40 CFR 471.53 - New source performance standards (NSPS).

Code of Federal Regulations, 2012 CFR

2012-07-01

... TSS 123 97.9 pH (1) (1) 1 Within the range of 7.5 to 10.0 at all times. (p) Molten salt rinse. Subpart... (pounds per million off-pounds) of refractory metals treated with molten salt Copper 0.810 0.386 Nickel 0...

Thermophysical Properties and Corrosion Characterization of Low Cost Lithium Containing Nitrate Salts Produced in Northern Chile for Thermal Energy Storage

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fernandez, Angel G.; Gomez, Judith C.; Galleguillos, Hector

In recent years, lithium containing salts have been studied for thermal energy storage (TES) systems applications, because of their optimal thermophysical properties. In solar power plants, lithium is seen as a way to improve the properties of molten salts used today. Lithium nitrate is a good candidate for sensible heat storage, due to its ability to increase the salt mixture's working temperature range. In the present research, thermophysical properties characterization of lithium nitrate containing salts, produced in Chile, have been carried out. Corrosion evaluations of carbon and low chromium steels were performed at 390 degrees C for 1000 hours. Thermophysicalmore » properties of the salt mixtures, such as thermal stability and heat capacity, were measured before and after corrosion tests. Chemical composition of the salts was also determined and an estimation of Chilean production costs is reported. Results showed that purity, thermal stability and heat capacity of the salts were reduced, caused by partial thermal decomposition and incorporation of corrosion products from the steel.« less

Impact of salt reduction on biogenic amines, fatty acids, microbiota, texture and sensory profile in traditional blood dry-cured sausages.

PubMed

Laranjo, Marta; Gomes, Ana; Agulheiro-Santos, Ana Cristina; Potes, Maria Eduarda; Cabrita, Maria João; Garcia, Raquel; Rocha, João Miguel; Roseiro, Luísa Cristina; Fernandes, Maria José; Fraqueza, Maria João; Elias, Miguel

2017-03-01

Meat industry needs to reduce salt in their products due to health issues. The present study evaluated the effect of salt reduction from 6% to 3% in two Portuguese traditional blood dry-cured sausages. Physicochemical and microbiological parameters, biogenic amines, fatty acids and texture profiles and sensory panel evaluations were considered. Differences due to salt reduction were perceptible in a faint decline of water activity, which slightly favoured microbial growth. Total biogenic amines content ranged from 88.86 to 796.68mgkg -1 fresh matter, with higher amounts, particularly of cadaverine, histamine and tyramine, in low-salt products. Still, histamine and other vasoactive amines remained at low levels, thus not affecting consumers' health. Regarding fatty acids, no significant differences were observed due to salt. However, texture profile analysis revealed lower resilience and cohesiveness in low-salt products, although no textural changes were observed by the sensory panel. Nevertheless, low-salt sausages were clearly preferred by panellists. Copyright © 2016 Elsevier Ltd. All rights reserved.

Can even minimal news coverage influence consumer health-related behaviour? A case study of iodized salt sales, Australia.

PubMed

Li, Mu; Chapman, Simon; Agho, Kingsley; Eastman, Creswell J

2008-06-01

Lack of iodine in the diet can cause a spectrum of conditions, known as iodine deficiency disorders (IDD). While iodized salt has been retailed in Australia since the 1960s, sales have remained low, at approximately 10% of total edible salt sales. Salt has never been promoted, advertised or discounted by retailers or manufacturers. Extensive news coverage of health issues has often been shown to influence consumer behaviour. But can even modest news coverage generate changes in consumer health-related behaviour? We report a significant increase (5.2%) in national iodized salt sales after a brief period of television and newspaper reports about IDD and the benefits of using iodized salt during and after the Australian National Iodine Nutrition Study in 2003 and 2004. We conclude that even brief news media exposure can influence health-related decisions.

Protic Salt Polymer Membranes: High-Temperature Water-Free Proton-Conducting Membranes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gervasio, Dominic Francis

2010-09-30

This research on proton-containing (protic) salts directly addresses proton conduction at high and low temperatures. This research is unique, because no water is used for proton ionization nor conduction, so the properties of water do not limit proton fuel cells. A protic salt is all that is needed to give rise to ionized proton and to support proton mobility. A protic salt forms when proton transfers from an acid to a base. Protic salts were found to have proton conductivities that are as high as or higher than the best aqueous electrolytes at ambient pressures and comparable temperatures without ormore » with water present. Proton conductivity of the protic salts occurs providing two conditions exist: i) the energy difference is about 0.8 eV between the protic-salt state versus the state in which the acid and base are separated and 2) the chemical constituents rotate freely. The physical state of these proton-conducting salts can be liquid, plastic crystal as well as solid organic and inorganic polymer membranes and their mixtures. Many acids and bases can be used to make a protic salt which allows tailoring of proton conductivity, as well as other properties that affect their use as electrolytes in fuel cells, such as, stability, adsorption on catalysts, environmental impact, etc. During this project, highly proton conducting (~ 0.1S/cm) protic salts were made that are stable under fuel-cell operating conditions and that gave highly efficient fuel cells. The high efficiency is attributed to an improved oxygen electroreduction process on Pt which was found to be virtually reversible in a number of liquid protic salts with low water activity (< 1% water). Solid flexible non-porous composite membranes, made from inorganic polymer (e.g., 10%indium 90%tin pyrophosphate, ITP) and organic polymer (e.g., polyvinyl pyridinium phosphate, PVPP), were found that give conductivity and fuel cell performances similar to phosphoric acid electrolyte with no need for hydration at ambient pressures. Synthesis and processing of these protic salts into proton-conducting membrane is far from optimized. This protic salt approach has great promise for more improvements in proton conducting membranes for making practical compact, lightweight and inexpensive fuel cells with uses ranging from small electronics (Power = 1 to 100 Watts) to transportation (kiloWatts) to stationary applications (>100 kiloWatts). This work clearly showed that proton can be conducted without water using protoic ionic liquids which are Bronsted salts which contain a proton and whose acid and base moieties have pK separated by more than 4 units and less than 14. A key finding is that the base used should be significantly different than the basicity of water or else water displaces the base and an ordinary acid membrane is left behind. This is the case where the acid moiety is sulfonic acid found on perfluorinated polymeric membranes. This PI suggests that a fruitful route for attaining highly proton-conductive stable protic salt membranes is to use the STABLE poly-phosphazene (-P=N-) polymer backbone with electrochemically STABLE pendant acid or base units on the phosphorous of poly-phosphazene and with suitable pK so the base is NOT the same pK as water. From this work this should give stable water-free proton conductors which should allow for stable fuel cells with Pt catalysts and possible with non-platinum catalyst for the hydrogen anode and oxygen cathode.« less

Community solar salt production in Goa, India

PubMed Central

2012-01-01

Traditional salt farming in Goa, India has been practised for the past 1,500 years by a few communities. Goa’s riverine estuaries, easy access to sea water and favourable climatic conditions makes salt production attractive during summer. Salt produced through this natural evaporation process also played an important role in the economy of Goa even during the Portuguese rule as salt was the chief export commodity. In the past there were 36 villages involved in salt production, which is now reduced to 9. Low income, lack of skilled labour, competition from industrially produced salt, losses incurred on the yearly damage of embankments are the major reasons responsible for the reduction in the number of salt pans. Salt pans (Mithagar or Mithache agor) form a part of the reclaimed waterlogged khazan lands, which are also utilised for aquaculture, pisciculture and agriculture. Salt pans in Goa experience three phases namely, the ceased phase during monsoon period of June to October, preparatory phase from December to January, and salt harvesting phase, from February to June. After the monsoons, the salt pans are prepared manually for salt production. During high tide, an influx of sea water occurs, which enters the reservoir pans through sluice gates. The sea water after 1–2 days on attaining a salinity of approximately 5ºBé, is released into the evaporator pans and kept till it attains a salinity of 23 - 25ºBé. The brine is then released to crystallizer pans, where the salt crystallises out 25 - 27ºBé and is then harvested. Salt pans form a unique ecosystem where succession of different organisms with varying environmental conditions occurs. Organisms ranging from bacteria, archaea to fungi, algae, etc., are known to colonise salt pans and may influence the quality of salt produced. The aim of this review is to describe salt farming in Goa’s history, importance of salt production as a community activity, traditional method of salt production and the biota associated with salt pans. PMID:23198813

Community solar salt production in Goa, India.

PubMed

Mani, Kabilan; Salgaonkar, Bhakti B; Das, Deepthi; Bragança, Judith M

2012-12-01

Traditional salt farming in Goa, India has been practised for the past 1,500 years by a few communities. Goa's riverine estuaries, easy access to sea water and favourable climatic conditions makes salt production attractive during summer. Salt produced through this natural evaporation process also played an important role in the economy of Goa even during the Portuguese rule as salt was the chief export commodity. In the past there were 36 villages involved in salt production, which is now reduced to 9. Low income, lack of skilled labour, competition from industrially produced salt, losses incurred on the yearly damage of embankments are the major reasons responsible for the reduction in the number of salt pans.Salt pans (Mithagar or Mithache agor) form a part of the reclaimed waterlogged khazan lands, which are also utilised for aquaculture, pisciculture and agriculture. Salt pans in Goa experience three phases namely, the ceased phase during monsoon period of June to October, preparatory phase from December to January, and salt harvesting phase, from February to June. After the monsoons, the salt pans are prepared manually for salt production. During high tide, an influx of sea water occurs, which enters the reservoir pans through sluice gates. The sea water after 1-2 days on attaining a salinity of approximately 5ºBé, is released into the evaporator pans and kept till it attains a salinity of 23 - 25ºBé. The brine is then released to crystallizer pans, where the salt crystallises out 25 - 27ºBé and is then harvested.Salt pans form a unique ecosystem where succession of different organisms with varying environmental conditions occurs. Organisms ranging from bacteria, archaea to fungi, algae, etc., are known to colonise salt pans and may influence the quality of salt produced.The aim of this review is to describe salt farming in Goa's history, importance of salt production as a community activity, traditional method of salt production and the biota associated with salt pans.

Boric ester-type molten salt via dehydrocoupling reaction.

PubMed

Matsumi, Noriyoshi; Toyota, Yoshiyuki; Joshi, Prerna; Puneet, Puhup; Vedarajan, Raman; Takekawa, Toshihiro

2014-11-14

Novel boric ester-type molten salt was prepared using 1-(2-hydroxyethyl)-3-methylimidazolium chloride as a key starting material. After an ion exchange reaction of 1-(2-hydroxyethyl)-3-methylimidazolium chloride with lithium (bis-(trifluoromethanesulfonyl) imide) (LiNTf2), the resulting 1-(2-hydroxyethyl)-3-methylimidazolium NTf2 was reacted with 9-borabicyclo[3.3.1]nonane (9-BBN) to give the desired boric ester-type molten salt in a moderate yield. The structure of the boric ester-type molten salt was supported by 1H-, 13C-, 11B- and 19F-NMR spectra. In the presence of two different kinds of lithium salts, the matrices showed an ionic conductivity in the range of 1.1 × 10⁻⁴-1.6 × 10⁻⁵ S cm⁻¹ at 51 °C. This was higher than other organoboron molten salts ever reported.

Boric Ester-Type Molten Salt via Dehydrocoupling Reaction

PubMed Central

Matsumi, Noriyoshi; Toyota, Yoshiyuki; Joshi, Prerna; Puneet, Puhup; Vedarajan, Raman; Takekawa, Toshihiro

2014-01-01

Novel boric ester-type molten salt was prepared using 1-(2-hydroxyethyl)-3-methylimidazolium chloride as a key starting material. After an ion exchange reaction of 1-(2-hydroxyethyl)-3-methylimidazolium chloride with lithium (bis-(trifluoromethanesulfonyl) imide) (LiNTf2), the resulting 1-(2-hydroxyethyl)-3-methylimidazolium NTf2 was reacted with 9-borabicyclo[3.3.1]nonane (9-BBN) to give the desired boric ester-type molten salt in a moderate yield. The structure of the boric ester-type molten salt was supported by 1H-, 13C-, 11B- and 19F-NMR spectra. In the presence of two different kinds of lithium salts, the matrices showed an ionic conductivity in the range of 1.1 × 10−4–1.6 × 10−5 S cm−1 at 51 °C. This was higher than other organoboron molten salts ever reported. PMID:25405738

[Effect of salts, stabilizing and destabilizing the structure of water, on the stacking association of adenosine].

PubMed

Maevskiĭ, A A; Sukhorukov, B I

1976-11-01

A spectrophotometric study, based on the concentration relationship of electron absorption spectra, of the effects of salts which stabilize and destabilize the water structure on the constant (K) of adenosine: stacking association has been carried out. A significant decrease of K was observed in NaClO4 which embodied strong destabilizing effect. Opposite effect was observed on other salts studied. According to K value the stacking-interaction of adenosine in the range of salt concentration 0 divided by 3M for different anions and cations are arranged in rows: SO4--greater than Cl- greater than ClO4-; Na+ greater than Li+greater than K+. The data obtained suggest that the effect of salts on thermostability of various oligo- and polynucleotides and on B leads to C DNA transition may be essentially concerned with the effect of both cations and anions of salts on the stacking-interaction of bases.

Lithium salts for advanced lithium batteries: Li-metal, Li-O 2, and Li-S

DOE PAGES

Younesi, Reza; Veith, Gabriel M.; Johansson, Patrik; ...

2015-06-01

Presently lithium hexafluorophosphate (LiPF 6) is the dominant Li-salt used in commercial rechargeable lithium-ion batteries (LIBs) based on a graphite anode and a 3-4 V cathode material. While LiPF 6 is not the ideal Li-salt for every important electrolyte property, it has a uniquely suitable combination of properties (temperature range, passivation, conductivity, etc.) rendering it the overall best Li-salt for LIBs. However, this may not necessarily be true for other types of Li-based batteries. Indeed, next generation batteries, for example lithium-metal (Li-metal), lithium-oxygen (Li-O 2), and lithium sulphur (Li-S), require a re-evaluation of Li-salts due to the different electrochemical andmore » chemical reactions and conditions within such cells. Furthermore, this review explores the critical role Li-salts play in ensuring in these batteries viability.« less

Numerical study on tilting salt finger in a laminar shear flow

NASA Astrophysics Data System (ADS)

Zhang, Xianfei; Wang, Ling-ling; Lin, Cheng; Zhu, Hai; Zeng, Cheng

2018-02-01

Salt fingers as a mixing mechanism in the ocean have been investigated for several decades, together with a key issue being focused on their convective evolution and flux ratio variation. However, related studies on tilting fingers in the ocean produced by shear flow have been ignored by previous researchers. In this paper, a 2-D numerical model is presented to study the evolution of the double-diffusion salt finger in a two-layer thermohaline system with laminar shear flow. The model is divided into a steady-state solver and double-diffusion convection system, aimed to reveal the effect of shear flow on salt fingers and analyze the mechanism behind the shear and fingers. Several cases are conducted for Re = 0 ˜ 900 to study the evolution of salt fingers in a laminar shear flow and the variation of salt flux with Re. The results show that salt fingers exist and tilt in the presence of laminar shear flow. The mass transport in the vertical direction is weakened as the Reynolds number increases. An asymmetric structure of the salt finger is discovered and accounts for the morphological tilt and salt flux reduction.

A Possible Regenerative, Molten-Salt, Thermoelectric Fuel Cell

NASA Technical Reports Server (NTRS)

Greenberg, Jacob; Thaller, Lawrence H.; Weber, Donald E.

1964-01-01

Molten or fused salts have been evaluated as possible thermoelectric materials because of the relatively good values of their figures of merit, their chemical stability, their long liquid range, and their ability to operate in conjunction with a nuclear reactor to produce heat. In general, molten salts are electrolytic conductors; therefore, there will be a transport of materials and subsequent decomposition with the passage of an electric current. It is possible nonetheless to overcome this disadvantage by using the decomposition products of the molten-salt electrolyte in a fuel cell. The combination of a thermoelectric converter and a fuel cell would lead to a regenerative system that may be useful.

Primary and secondary room temperature molten salt electrochemical cells

NASA Astrophysics Data System (ADS)

Reynolds, G. F.; Dymek, C. J., Jr.

1985-07-01

Three novel primary cells which use room temperature molten salt electrolytes are examined and found to have high open circuit potentials in the 1.75-2.19 V range, by comparison with the Al/AlCl3-MEICl concentration cell; their cathodes were of FeCl3-MEICl, WCl6-MEICl, and Br2/reticulated vitreous carbon together with Pt. Also, secondary electrochemical cell candidates were examined which combined the reversible Al/AlCl3-MEICl electrode with reversible zinc and cadmium molten salt electrodes to yield open circuit potentials of about 0.7 and 1.0 V, respectively. Room temperature molten salts' half-cell reduction potentials are given.

Distinct Osmoadaptation Strategies in the Strict Halophilic and Halotolerant Bacteria Isolated from Lunsu Salt Water Body of North West Himalayas.

PubMed

Vaidya, Shivani; Dev, Kamal; Sourirajan, Anuradha

2018-07-01

Two strict halophilic bacterial strains, Halobacillus trueperi SS1, and Halobacillus trueperi SS3, and three halotolerant bacterial strains, Shewanella algae SS2, Halomonas venusta SS5, and Marinomonas sp. SS8 of Lunsu salt water body, Himachal Pradesh, India, were selected to study the mechanism of salt tolerance and the role of osmolytes therein. A combination of flame photometry, chromatographic and colorimetric assays was used to study the mechanism of salt tolerance in the selected strict halophilic and halotolerant bacterial strains. The strict halophiles and, one of the halotolerants, Marinomonas sp. SS8 were found to utilize both "salt-in strategy" and "accumulation of compatible solutes strategy" for osmoregulation in hypersaline conditions. On the contrary, the remaining two halotolerants used "accumulation of compatible solutes strategy" under saline stress and not the "salt-in strategy". The present study suggests towards distinct mechanisms of salt tolerance in the two classes, wherein strict halophiles accumulate compatible solutes as well as adopt salt-in strategy, while the halotolerant bacteria accumulate a range of compatible solutes, except Marinomonas sp. SS8, which utilizes both the strategies to combat salt stress.

The Origin of Salt-Encased Sediment Packages: Observations from the SE Precaspian Basin (Kazakhstan)

NASA Astrophysics Data System (ADS)

Fernandez, Naiara; Duffy, Oliver B.; Hudec, Michael R.; Jackson, Martin P. A.; Burg, George; Jackson, Christopher A.-L.; Dooley, Tim P.

2017-04-01

Intrasalt sediment packages containing siliciclastic sediments, carbonate sediments, or non-halite evaporites such as gypsum or anhydrite are common within most salt sequences. Intrasalt sediment packages may have been deposited before, during, or after salt deposition and be incorporated into the salt by various processes. Understanding the origin and evolution of intrasalt sediment packages may yield important insights into the tectonic and geodynamic history of the basin, and also into the understanding of salt tectonics. Despite the importance of intrasalt sediment packages, currently there is no systematic description of their possible origins and their distinguishing criteria. This work is divided in three parts. First, we outline the possible origins of intrasalt sediment packages, as well as criteria to determine if they originated as subsalt, suprasalt or intrasalt sequences. Second, we examine how sediment packages that originated on top of salt, such as minibasins, can be encased within salt. We propose four key processes by which salt can be expelled and emplaced above minibasins to encase them: a) salt expulsion from beneath a minibasin experiencing density-driven subsidence; b) salt expulsion from beneath adjacent subsiding minibasins; c) salt expulsion associated with lateral shortening; d) override of minibasins by a salt sheet sourced from elsewhere. Third, we present a case study from the SE Precaspian Basin, Kazakhstan, where, using a borehole-constrained 3D seismic reflection dataset, the proposed criteria are applied to an area with abundant, newly discovered sediment packages within salt.

Effectiveness of highway-drainage systems in preventing contamination of ground water by road salt, Route 25, southeastern Massachusetts; description of study area, data collection programs, and methodology

USGS Publications Warehouse

Church, P.E.; Armstrong, D.S.; Granato, G.E.; Stone, V.J.; Smith, K.P.; Provencher, P.L.

1996-01-01

Four test sites along a 7-mile section of Route 25 in southeastern Massachusetts, each representing a specific highway-drainage system, were instrumented to determine the effectiveness of the drainage systems in preventing contamination of ground water by road salt. One of the systems discharges highway runoff onsite through local drainpipes. The other systems use trunkline drainpipes through which runoff from highway surfaces, shoulders, and median strips is diverted and discharged into either a local stream or a coastal waterway. Route 25 was completed and opened to traffic in the summer of 1987. Road salt was first applied to the highway in the winter of 1987-88. The study area is on a thick outwash plain composed primarily of sand and gravel. Water-table depths range from 15 to 60 feet below land surface at the four test sites. Ground-water flow is in a general southerly direction, approximately perpendicular to the highway. Streamflow in the study area is controlled primarily by ground-water discharge. Background concentrations of dissolved chloride, sodium, and calcium-the primary constituents of road salt-are similar in ground water and surface water and range from 5 to 20, 5 to 10, and 1 to 5 milligrams per liter, respectively. Data-collection programs were developed for monitoring the application of road salt to the highway, the quantity of road-salt water entering the ground water, diverted through the highway-drainage systems, and entering a local stream. The Massachusetts Highway Department monitored road salt applied to the highway and reported these data to the U.S. Geological Survey. The U.S. Geological Survey designed and operated the ground-water, highway- drainage, and surface-water data-collection programs. A road-salt budget will be calculated for each test site so that the effectiveness of the different highway-drainage systems in preventing contamination of ground water by road salt can be determined.

The Structures of Fibronectin Adsorbed on Polyelectrolyte Thin Films

NASA Astrophysics Data System (ADS)

Shin, Kwanwoo; Satija, Sushil; Fang, Xiao-Hua; Li, Bin-Quan; Nadine, Pernodet; Miriam, Rafailovich; Sokolov, Jonathan; Arach, Goldar; Roser, Steve

2002-03-01

We have shown that it is possible to form a fibrilar network of fibronectin on a polyelectrolyte polymer film whose dimensions are similar to those reported on the extra cellular matrix. The fibronectin network was observed to form only when the charge density of the polymer was in excess of the natural charge density of the cell wall. Furthermore, the self-organized fibronectin layer was much thicker than the polymer film, indicating that long ranged interaction may play a key role in the assembly process. It is therefore important to understand the structure of the polymer layer/protein interface. Here we report on a neutron reflectivity study where we explore the structure of the polyelectrolyte layer, in this case sulfonated polystyrene (PSS_x.), with varying degree of sulfonation (x<30%), as a function of sulfur content and counter ion concentration. These results are then correlated with systemic study of the adsorption and the multilayer formation of fibronectin as a function of incubation time for various sulfonation levels of PSS_x. Furthermore, the surface charge on the substrates can be strongly influenced by the presence of salt ions, it is important to understand changes due to electrostatic interactions occurring in the various salt conditions. Complementary X-ray reflection was used to determine the salt density profile associating with the internal ionic polymer matrix. This work was funded in part of the NSF-MRSEC program.

Unified molecular picture of the surfaces of aqueous acid, base, and salt solutions.

PubMed

Mucha, Martin; Frigato, Tomaso; Levering, Lori M; Allen, Heather C; Tobias, Douglas J; Dang, Liem X; Jungwirth, Pavel

2005-04-28

The molecular structure of the interfacial regions of aqueous electrolytes is poorly understood, despite its crucial importance in many biological, technological, and atmospheric processes. A long-term controversy pertains between the standard picture of an ion-free surface layer and the strongly ion specific behavior indicating in many cases significant propensities of simple inorganic ions for the interface. Here, we present a unified and consistent view of the structure of the air/solution interface of aqueous electrolytes containing monovalent inorganic ions. Molecular dynamics calculations show that in salt solutions and bases the positively charged ions, such as alkali cations, are repelled from the interface, whereas the anions, such as halides or hydroxide, exhibit a varying surface propensity, correlated primarily with the ion polarizability and size. The behavior of acids is different due to a significant propensity of hydronium cations for the air/solution interface. Therefore, both cations and anions exhibit enhanced concentrations at the surface and, consequently, these acids (unlike bases and salts) reduce the surface tension of water. The results of the simulations are supported by surface selective nonlinear vibrational spectroscopy, which reveals among other things that the hydronium cations are present at the air/solution interface. The ion specific propensities for the air/solution interface have important implications for a whole range of heterogeneous physical and chemical processes, including atmospheric chemistry of aerosols, corrosion processes, and bubble coalescence.

Interactions between Bacteria and Bile Salts in the Gastrointestinal and Hepatobiliary Tracts

PubMed Central

Urdaneta, Verónica; Casadesús, Josep

2017-01-01

Bile salts and bacteria have intricate relationships. The composition of the intestinal pool of bile salts is shaped by bacterial metabolism. In turn, bile salts play a role in intestinal homeostasis by controlling the size and the composition of the intestinal microbiota. As a consequence, alteration of the microbiome–bile salt homeostasis can play a role in hepatic and gastrointestinal pathological conditions. Intestinal bacteria use bile salts as environmental signals and in certain cases as nutrients and electron acceptors. However, bile salts are antibacterial compounds that disrupt bacterial membranes, denature proteins, chelate iron and calcium, cause oxidative damage to DNA, and control the expression of eukaryotic genes involved in host defense and immunity. Bacterial species adapted to the mammalian gut are able to endure the antibacterial activities of bile salts by multiple physiological adjustments that include remodeling of the cell envelope and activation of efflux systems and stress responses. Resistance to bile salts permits that certain bile-resistant pathogens can colonize the hepatobiliary tract, and an outstanding example is the chronic infection of the gall bladder by Salmonella enterica. A better understanding of the interactions between bacteria and bile salts may inspire novel therapeutic strategies for gastrointestinal and hepatobiliary diseases that involve microbiome alteration, as well as novel schemes against bacterial infections. PMID:29043249

Oral Sustained Release of a Hydrophilic Drug Using the Lauryl Sulfate Salt/Complex.

PubMed

Kasashima, Yuuki; Yoshihara, Keiichi; Yasuji, Takehiko; Sako, Kazuhiro; Uchida, Shinya; Namiki, Noriyuki

2016-01-01

The objective of this study was to establish the key factor of the lauryl sulfate (LS) salt/complex for sustained release of a hydrophilic drug at various physiological pH levels. Mirabegron is a hydrophilic drug that exhibits pH-dependent solubility. Sodium lauryl sulfate (SLS) bound to mirabegron in a stoichiometric manner. The formation of the LS salt/complex significantly reduced mirabegron solubility and helped achieve sustained release of mirabegron over a wide range of pH levels. In addition to SLS, other additives containing a sulfate group formed salts/complexes with mirabegron and reduced its solubility at different pH levels. Furthermore, octyl sulfate (OS), myristyl sulfate (MS), and cetyl sulfate (CS) salts/complexes, which contain alkyl chains of different lengths, showed a lower solubility than mirabegron and promoted sustained release of mirabegron. The rank order of solubility and dissolution rate were as follows: OS salt/complex>LS salt/complex>MS salt/complex>CS salt/complex, which corresponded to the rank of alkyl chain lengths. We conclude that the presence of a sulfate group and the length of the alkyl chain are key factors of the LS salt/complex for sustained release of a hydrophilic drug at various physiological pH levels.

Microbial Successions and Metabolite Changes during Fermentation of Salted Shrimp (Saeu-Jeot) with Different Salt Concentrations

PubMed Central

Lee, Se Hee; Jung, Ji Young; Jeon, Che Ok

2014-01-01

To investigate the effects of salt concentration on saeu-jeot (salted shrimp) fermentation, four sets of saeu-jeot samples with 20%, 24%, 28%, and 32% salt concentrations were prepared, and the pH, bacterial and archaeal abundances, bacterial communities, and metabolites were monitored during the entire fermentation period. Quantitative PCR showed that Bacteria were much more abundant than Archaea in all saeu-jeot samples, suggesting that bacterial populations play more important roles than archaeal populations even in highly salted samples. Community analysis indicated that Vibrio, Photobacterium, Psychrobacter, Pseudoalteromonas, and Enterovibrio were identified as the initially dominant genera, and the bacterial successions were significantly different depending on the salt concentration. During the early fermentation period, Salinivibrio predominated in the 20% salted samples, whereas Staphylococcus, Halomonas, and Salimicrobium predominated in the 24% salted samples; eventually, Halanaerobium predominated in the 20% and 24% salted samples. The initially dominant genera gradually decreased as the fermentation progressed in the 28% and 32% salted samples, and eventually Salimicrobium became predominant in the 28% salted samples. However, the initially dominant genera still remained until the end of fermentation in the 32% salted samples. Metabolite analysis showed that the amino acid profile and the initial glycerol increase were similar in all saeu-jeot samples regardless of the salt concentration. After 30–80 days of fermentation, the levels of acetate, butyrate, and methylamines in the 20% and 24% salted samples increased with the growth of Halanaerobium, even though the amino acid concentrations steadily increased until approximately 80–107 days of fermentation. This study suggests that a range of 24–28% salt concentration in saeu-jeot fermentation is appropriate for the production of safe and tasty saeu-jeot. PMID:24587230

Development and Optimization of Voltammetric Methods for Real Time Analysis of Electrorefiner Salt with High Concentrations of Actinides and Fission Products

DOE Office of Scientific and Technical Information (OSTI.GOV)

Simpson, Michael F.; Phongikaroon, Supathorn; Zhang, Jinsuo

This project addresses the problem of achieving accurate material control and accountability (MC&A) around pyroprocessing electrorefiner systems. Spent nuclear fuel pyroprocessing poses a unique challenge with respect to reprocessing technology in that the fuel is never fully dissolved in the process fluid. In this case, the process fluid is molten, anhydrous LiCl-KCl salt. Therefore, there is no traditional input accountability tank. However, electrorefiners (ER) accumulate very large quantities of fissile nuclear material (including plutonium) and should be well safeguarded in a commercial facility. Idaho National Laboratory (INL) currently operates a pyroprocessing facility for treatment of spent fuel from Experimental Breedermore » Reactor-II with two such ER systems. INL implements MC&A via a mass tracking model in combination with periodic sampling of the salt and other materials followed by destructive analysis. This approach is projected to be insufficient to meet international safeguards timeliness requirements. A real time or near real time monitoring method is, thus, direly needed to support commercialization of pyroprocessing. A variety of approaches to achieving real time monitoring for ER salt have been proposed and studied to date—including a potentiometric actinide sensor for concentration measurements, a double bubbler for salt depth and density measurements, and laser induced breakdown spectroscopy (LIBS) for concentration measurements. While each of these methods shows some promise, each also involves substantial technical complexity that may ultimately limit their implementation. Yet another alternative is voltammetry—a very simple method in theory that has previously been tested for this application to a limited extent. The equipment for a voltammetry system consists of off-the-shelf components (three electrodes and a potentiostat), which results in substantial benefits relative to cost and robustness. Based on prior knowledge of electrochemical reduction potentials for each of the species of interest, voltammetry can be used to quantify concentrations of a variety of elemental species—including uranium, plutonium, minor actinides, and rare earths. Various methods have been tested by other researchers to date—including cyclic voltammetry, square wave voltammetry, normal pulse voltammetry, etc. In most cases, it has been observed that there is a very limited concentration range for which the output can be readily correlated with concentration in the salt. Furthermore, testing to date has been limited to simple ternary salts with only a single element being quantified. While incomplete for application to MC&A for pyroprocessing, these results lead us to believe that voltammetry can be optimized based on salt properties and fundamental electrochemical rate processes to yield a highly accurate and robust method. This project is divided into four tasks jointly executed by three university research groups. This includes experimental measurement of key physical data on the systems of interest, development of a predictive voltammetry model, experimental validation of the voltammetry model, and design/verification of an optimized measurement method. This project supports the goals of the US-ROK Joint Fuel Cycle Study in addition to the NA-24 Office of the National Nuclear Security Agency and the International Atomic Energy Agency (IAEA).« less

Myoclonic encephalopathy due to bismuth salts: treatment with dimercaprol and analysis of CSF transmitters.

PubMed

Molina, J A; Calandre, L; Bermejo, F

1989-03-01

Two cases of myoclonic encephalopathy due to bismuth salts intoxication are reported. In both, treatment with dimercaprol led to clinical recovery. This therapy was shown to enhance bismuth clearance. We also present data on the CSF metabolites dopamine, norepinephrine and serotonin of one patient.

Is It Possible to Distinguish Between Dust and Salt Aerosol Over Waters with Unknown Chlorophyll Concentrations Using Spectral Remote Sensing?

NASA Technical Reports Server (NTRS)

Levy, R. C.; Kaufman, Y. J.

1999-01-01

Atmospheric aerosol has uncertain impacts on the global climate system, as well as on atmospheric and bio-geo-chemical processes of regional and local scales. EOS-MODIS is one example of a satellite sensor designed to improve understanding of the aerosols' type, size and distribution at all temporal and spatial scales. Ocean scientists also plan to use data from EOS-MODIS to assess the temporal and spatial coverage of in-water chlorophyll. MODIS is the first sensor planned to observe the combined ocean-atmosphere system with a wide spectral range (from 410 to 2200 nm). Dust aerosol and salt aerosol have similar spectral signals for wavelengths longer than 550 nm, but because dust selectively absorbs blue light, they have divergent signals in the blue wavelength regions (412 to 490 nm). Chlorophyll also selectively absorbs blue radiation, so that varying chlorophyll concentrations produces a highly varying signal in the blue regions, but less variability in the green, and almost no signal in the red to mid-infrared regions. Thus, theoretically, it may be difficult to differentiate dust and salt in the presence of unknown chlorophyll in the ocean. This study attempts to address the cases in which aerosol and chlorophyll signals can and cannot be separated. For the aerosol spectra, we use the aerosol lookup table from the operational MODIS aerosol-over-ocean algorithm, and for chlorophyll spectra, we use the SeaBAM data set (created for SeaWiFS). We compare the signals using Principal Component Analysis and attempt to retrieve both chlorophyll and aerosol properties using a variant of the operational MODIS aerosol-over-ocean algorithm. Results show that for small optical depths, less than 0.5, it is not possible to differentiate between dust and salt and to determine the chlorophyll concentration at the same time. For larger aerosol optical depths, the chlorophyll signals are comparatively insignificant, and we can hope to distinguish between dust and salt.

ABCB4 missense mutations D243A, K435T, G535D, I490T, R545C, and S978P significantly impair the lipid floppase and likely predispose to secondary pathologies in the human population.

PubMed

Andress, Edward J; Nicolaou, Michael; McGeoghan, Farrell; Linton, Kenneth J

2017-07-01

Bile salts are natural detergents required to solubilise dietary fat and lipid soluble vitamins. They are synthesised in hepatocytes and secreted into the luminal space of the biliary tree by the bile salt export pump (BSEP), an ATP-binding cassette (ABC) transporter in the canalicular membrane. BSEP deficiency causes cytotoxic accumulation of bile salts in the hepatocyte that results in mild-to-severe forms of cholestasis. The resulting inflammation can also progress to hepatocellular cancer via a novel mechanism involving upregulation of proliferative signalling pathways. A second ABC transporter of the canalicular membrane is also critical for bile formation. ABCB4 flops phosphatidylcholine into the outer leaflet of the membrane to be extracted by bile salts in the canalicular space. These mixed micelles reduce the detergent action of the bile salts and protect the biliary tree from their cytotoxic activity. ABCB4 deficiency also causes cholestasis, and might be expected to cause cholangitis and predispose to liver cancer. Non-synonymous SNPs in ABCB4 have now been described in patients with liver cancer or with inflammatory liver diseases that are known to predispose to cancer, but data showing that the SNPs are sufficiently deleterious to be an etiological factor are lacking. Here, we report the first characterisation at the protein level of six ABCB4 variants (D243A, K435T, G535D, I490T, R545C, and S978P) previously found in patients with inflammatory liver diseases or liver cancer. All significantly impair the transporter with a range of phenotypes exhibited, including low abundance, intracellular retention, and reduced floppase activity, suggesting that ABCB4 deficiency is the root cause of the pathology in these cases.

Detailed spectroscopic analysis of chloride salt deposits in Terra Sirenum, Mars

NASA Astrophysics Data System (ADS)

Osterloo, M. M.; Glotch, T. D.; Bandfield, J. L.

2015-12-01

Chloride salt-bearing deposits have been identified throughout the southern highlands of Mars [1] based on the lack of diagnostic spectral features of anhydrous chlorides in both the visible near infrared (VNIR) and middle infrared (MIR) wavelength ranges [1,2]. A puzzling aspect of martian chloride deposits is the apparent lack of other weathering or evaporite phases associated with most of the deposits. A global analysis over the chloride salt sites conducted by [3] found that only ~9% of the deposits they analyzed were associated with minerals such as phyllosilicates. Most of these occurrences are in Terra Sirenum where [4] noted that salt-bearing deposits lie stratigraphically above Noachian phyllosilicates. Although a variety of formation mechanisms have been proposed for these intriguing deposits, detailed geologic mapping by [5] suggests that surface water and evaporation played a dominant role. On Earth, evaporative settings are often characterized by a multitude of evaporite and phyllosilicate phases including carbonates, sulfates, and nitrates. [6] evaluated chemical divides and brine evolution for martian systems and their results indicate three pathways wherein late-stage brines favor chloride precipitation. In each case the pathway to chloride formation includes precipitation of carbonates (calcite, siderite, and/or magnesite) and sulfates (gypsum, melanterite, and/or epsomite). Here, we present the results of our detailed and systematic spectroscopic study to identify additional evaporite phases associated with salt/silicate mixtures in Terra Sirenum. [1] Osterloo et al. (2008) Science, 319, [2] Glotch, T. D. et al. (2013) Lunar and Planet. Sci. XLIV, abstract #1549 [3] Ruesch, O. et al. (2012), J. Geophys. Res., 117, E00J13 [4] Glotch, T. D. et al. (2010) Geophys. Res. Lett. 37, L16202, [5] Osterloo, M. M. and B. M Hynek (2015) Lunar and Planet. Sci XLVI. Abstract #1054 [6] Tosca, N. J. and S. M. McLennan (2006), Earth and Planet. Sci. Lett., 241.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Younesi, Reza; Veith, Gabriel M.; Johansson, Patrik

Presently lithium hexafluorophosphate (LiPF 6) is the dominant Li-salt used in commercial rechargeable lithium-ion batteries (LIBs) based on a graphite anode and a 3-4 V cathode material. While LiPF 6 is not the ideal Li-salt for every important electrolyte property, it has a uniquely suitable combination of properties (temperature range, passivation, conductivity, etc.) rendering it the overall best Li-salt for LIBs. However, this may not necessarily be true for other types of Li-based batteries. Indeed, next generation batteries, for example lithium-metal (Li-metal), lithium-oxygen (Li-O 2), and lithium sulphur (Li-S), require a re-evaluation of Li-salts due to the different electrochemical andmore » chemical reactions and conditions within such cells. Furthermore, this review explores the critical role Li-salts play in ensuring in these batteries viability.« less

View of the Salt Lake City, Utah area

NASA Image and Video Library

1973-08-30

SL3-22-0322 (July-September 1973) --- An oblique view of the Salt Lake City, Utah area as photographed from Earth orbit by one of the six lenses of the Itek-furnished S190-A Multispectral Photographic Facility Experiment aboard the Skylab space station. Approximately two-thirds of the Great Salt Lake is in view. The smaller body of water south of Salt Lake City is Utah Lake. The Wasatch Range is on the east side of the Great Salt Lake. Federal agencies participating with NASA on the EREP project are the Departments of Agriculture, Commerce, Interior, the Environmental Protection Agency and the Corps of Engineers. All EREP photography is available to the public through the Department of Interior?s Earth Resources Observations Systems Data Center, Sioux Falls, South Dakota, 57198. Photo credit: NASA

Electroosmotic velocity in an array of parallel soft cylinders in a salt-free medium.

PubMed

Ohshima, Hiroyuki

2004-11-15

A theory of electroosmosis in an array of parallel soft cylinders (i.e. polyelectrolyte-coated cylinders) in a salt-free medium is presented. It is shown that there is a certain critical value of the particle charge and that if the particle charge is greater than the critical value, then the electroosmotic velocity becomes constant independent of the particle charge due to the counterion condensation effects, as in the case of other electrokinetic phenomena in salt-free media.

Understanding the Spatio-Temporal Dynamics of Denitrification in an Oregon Salt Marsh

EPA Science Inventory

Salt marshes are highly susceptible to a range of climate change effects (e.g., sea-level rise, salinity changes, storm severity, shifts in vegetation across watershed). It is unclear how these effects will alter the spatial and temporal dynamics of denitrification, a potential p...

Biotoxicity of Mars Analog Soils: Microbial Dispersal into Desiccated Soils Versus Emplacement in Salt or Ice Inclusion Fluids

NASA Astrophysics Data System (ADS)

Schuerger, A. C.; Ming, D. W.; Golden, D. C.

2010-04-01

Six Mars analog soils were prepared to simulate a range of potentially biotoxic soils. Interactive effects of high-salt, desiccation, and low pressure were responsible for significant decreases in viable numbers of microbial species tested under martian conditions for 7 d.

Salt additions increase soil nitrate leaching: Implications for near-coastal watershed biogeochemistry

EPA Science Inventory

Deposition of sea salt aerosols is often elevated along the coast relative to inland areas, yet little is known about the effects of this deposition on terrestrial ecosystem biogeochemistry. Spatial patterns of stream chemistry in the Oregon Coast Range led us to hypothesize tha...

Effects of PV Module Soiling on Glass Surface Resistance and Potential-Induced Degradation: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hacke, Peter; Burton, Patrick; Hendrickson, Alex

2015-12-03

The sheet resistance of three soil types (Arizona road dust, soot, and sea salt) on glass were measured by the transmission line method as a function of relative humidity (RH) between 39% and 95% at 60 degrees C. Sea salt yielded a 3.5 order of magnitude decrease in resistance on the glass surface when the RH was increased over this RH range. Arizona road dust showed reduced sheet resistance at lower RH, but with less humidity sensitivity over the range tested. The soot sample did not show significant resistivity change compared to the unsoiled control. Photovoltaic modules with sea saltmore » on their faces were step-stressed between 25% and 95% RH at 60 degrees C applying -1000 V bias to the active cell circuit. Leakage current from the cell circuit to ground ranged between two and ten times higher than that of the unsoiled controls. Degradation rate of modules with salt on the surface increased with increasing RH and time.« less

One-pot in situ mixed film formation by azo coupling and diazonium salt electrografting.

PubMed

Esnault, Charles; Delorme, Nicolas; Louarn, Guy; Pilard, Jean-François

2013-06-24

So simple: The in situ synthesis of an aryldiazonium salt and an azo-aryldiazonium salt by azo coupling from sulfanilic acid and aniline is reported. Formation of a mixed organic layer is monitored by cyclic voltammetry and atomic force microscopy. A compact mixed layer is obtained with a global roughness of 0.4 nm and 10-15 % vertical extension in the range 1.5-6 nm. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Comparative Toxicities of Salts on Microbial Processes in Soil

PubMed Central

Maheshwari, Arpita; Bengtson, Per; Rousk, Johannes

2016-01-01

Soil salinization is a growing threat to global agriculture and carbon sequestration, but to date it remains unclear how microbial processes will respond. We studied the acute response to salt exposure of a range of anabolic and catabolic microbial processes, including bacterial (leucine incorporation) and fungal (acetate incorporation into ergosterol) growth rates, respiration, and gross N mineralization and nitrification rates. To distinguish effects of specific ions from those of overall ionic strength, we compared the addition of four salts frequently associated with soil salinization (NaCl, KCl, Na2SO4, and K2SO4) to a nonsaline soil. To compare the tolerance of different microbial processes to salt and to interrelate the toxicity of different salts, concentration-response relationships were established. Growth-based measurements revealed that fungi were more resistant to salt exposure than bacteria. Effects by salt on C and N mineralization were indistinguishable, and in contrast to previous studies, nitrification was not found to be more sensitive to salt exposure than other microbial processes. The ion-specific toxicity of certain salts could be observed only for respiration, which was less inhibited by salts containing SO42− than Cl− salts, in contrast to the microbial growth assessments. This suggested that the inhibition of microbial growth was explained solely by total ionic strength, while ion-specific toxicity also should be considered for effects on microbial decomposition. This difference resulted in an apparent reduction of microbial growth efficiency in response to exposure to SO42− salts but not to Cl− salts; no evidence was found to distinguish K+ and Na+ salts. PMID:26801570

Inefficacy of osmotic backwash induced by sodium chloride salt solution in controlling SWRO membrane fouling

NASA Astrophysics Data System (ADS)

Farooque, A. Mohammed; Al-Jeshi, Subhi; Saeed, Mohamed O.; Alreweli, Ali

2014-12-01

A study was conducted to evaluate the efficacy of osmotic backwash induced by high salt (NaCl) concentration solution on feed side of seawater reverse osmosis (SWRO) membranes, online and offline, in controlling membrane fouling and therefore minimizing/eliminating the need for chemical cleaning. SWRO membranes were deliberately fouled by feeding seawater from an open intake located on the Arabian Gulf Coast without dosing chemicals. The fouled membranes were subjected to offline cleaning with the salt solution of up to 25 % concentration. Despite the partial removal of foulants from the membrane surface, SWRO membrane performance could not be restored, indicating the ineffectiveness of osmotic backwash in aiding offline salt cleaning. Similarly, online osmotic backwash was found to be not only ineffective in removing foulants from membrane surfaces but actually increased the fouling rate, as indicated by faster fouling rates compared to other cases. Although the driving force required for the osmotic backwash existed, the generated back flow proved to be insufficient to detach foulants from membrane surfaces. During the study period, the average SWRO membrane flux was maintained between 19 and 23 LMH, whereas the average generated back flow flux by high salt concentration solution was only 11 LMH, which was not adequate to remove foulants from membrane surfaces. Moreover, it seems that the membrane configuration as well as inherent microstructure of SWRO membrane places certain constraints on the osmotic backwash process and renders osmotic backwash ineffective in tackling SWRO membrane fouling. Hence, chemical cleaning is essential to restore SWRO membrane performance whenever fouling occurs, and the use of highly concentrated salt solution does not have any significant benefit. Membrane autopsy revealed only an insignificant accumulation of biofouling layer despite the absence of disinfection. However, it was shown that culturable biofilm bacteria species isolated from membranes tolerated exposure to high salt concentrations at pH range of 7-8. In addition, the overall findings of the study indicate that SWRO membranes can be operated in Gulf seawater at a recovery of 30 % without using any chemicals, such as coagulant, disinfectant and antiscalant, for an acceptable period of time without performing membrane cleaning. This is highly likely, if media filters are used in the pretreatment and SWRO membranes are operated at normal flux and recovery ratio.

Anthropogenic contamination of tap water, beer, and sea salt

PubMed Central

2018-01-01

Plastic pollution has been well documented in natural environments, including the open waters and sediments within lakes and rivers, the open ocean and even the air, but less attention has been paid to synthetic polymers in human consumables. Since multiple toxicity studies indicate risks to human health when plastic particles are ingested, more needs to be known about the presence and abundance of anthropogenic particles in human foods and beverages. This study investigates the presence of anthropogenic particles in 159 samples of globally sourced tap water, 12 brands of Laurentian Great Lakes beer, and 12 brands of commercial sea salt. Of the tap water samples analyzed, 81% were found to contain anthropogenic particles. The majority of these particles were fibers (98.3%) between 0.1–5 mm in length. The range was 0 to 61 particles/L, with an overall mean of 5.45 particles/L. Anthropogenic debris was found in each brand of beer and salt. Of the extracted particles, over 99% were fibers. After adjusting for particles found in lab blanks for both salt and beer, the average number of particles found in beer was 4.05 particles/L with a range of 0 to 14.3 particles/L and the average number of particles found in each brand of salt was 212 particles/kg with a range of 46.7 to 806 particles/kg. Based on consumer guidelines, our results indicate the average person ingests over 5,800 particles of synthetic debris from these three sources annually, with the largest contribution coming from tap water (88%). PMID:29641556

Salting-out assisted liquid-liquid extraction combined with gas chromatography-mass spectrometry for the determination of pyrethroid insecticides in high salinity and biological samples.

PubMed

Niu, Zongliang; Yu, Chunwei; He, Xiaowen; Zhang, Jun; Wen, Yingying

2017-09-05

A salting-out assisted liquid-liquid extraction (SALLE) combined with gas chromatography-mass spectrometry (GC-MS) method was developed for the determination of four pyrethroid insecticides (PYRs) in high salinity and biological samples. Several parameters including sample pH, salting-out solution volume and salting-out solution pH influencing the extraction efficiency were systematically investigated with the aid of orthogonal design. The optimal extraction conditions of SALLE were: 4mL of salting-out solution with pH=4 and the sample pH=3. Under the optimum extraction and determination conditions, good responses for four PYRs were obtained in a range of 5-5000ng/mL, with linear coefficients greater than 0.998. The recoveries of the four PYRs ranged from 74% to 110%, with standard deviations ranging from 1.8% to 9.8%. The limits of detection based on a signal-to-noise ratio of 3 were between 1.5-60.6ng/mL. The method was applied to the determination of PYRs in urine, seawater and wastewater samples with a satisfactory result. The results demonstrated that this SALLE-GC-MS method was successfully applied to determine PYRs in high salinity and biological samples. SALLE avoided the need for the elimination of salinity and protein in the sample matrix, as well as clean-up of the extractant. Most of all, no centrifugation or any special apparatus are required, make this a promising method for rapid sample preparation procedure. Copyright © 2017 Elsevier B.V. All rights reserved.

Impact of corrosion test container material in molten fluorides

DOE PAGES

Olson, Luke C.; Fuentes, Roderick E.; Martinez-Rodriguez, Michael J.; ...

2015-10-15

The effects of crucible material choice on alloy corrosion rates in immersion tests in molten LiF–NaF–KF (46.5–11.5-42 mol. %) salt held at 850 °C for 500 hrs are described. Four crucible materials were studied. Molten salt exposures of Incoloy-800H in graphite, Ni, Incoloy-800H, and pyrolytic boron nitride (PyBN) crucibles all led to weight-loss in the Incoloy-800H coupons. Alloy weight loss was ~30 times higher in the graphite and Ni crucibles in comparison to the Incoloy-800H and PyBN crucibles. It is hypothesized galvanic coupling between the alloy coupons and crucible materials contributed to the higher corrosion rates. Alloy salt immersion inmore » graphite and Ni crucibles had similar weight-loss hypothesized to occur due to the rate limiting out diffusion of Cr in the alloys to the surface where it reacts with and dissolves into the molten salt, followed by the reduction of Cr from solution at the molten salt and graphite/Ni interfaces. As a result, both the graphite and the Ni crucibles provided sinks for the Cr, in the formation of a Ni–Cr alloy in the case of the Ni crucible, and Cr carbide in the case of the graphite crucible.« less

Crater Formation Above Salt Caverns: Piston vs Hour-glass

NASA Astrophysics Data System (ADS)

Berest, P.

2016-12-01

Conditions leading to crater formation above salt caverns are discussed. In most cases, at the end of leaching, the cavern roof had reached the top of the salt formation, allowing direct contact between brine and marl (or argillite) layers that compose the overburden of the salt formation. These layers are prone to weathering when in contact with saturated brine. Stoping takes place, and the cavern roof rises through the overburden. This process may be several years or dozens of years long. In Lorraine salt formations, stoping stops when the rising cavern top reaches a competent layer, the Beaumont Dolomite. Operators then lower cavern-brine pressure to trigger collapse. A rigid cylinder of rock (a "piston") drops into the cavern, and a crater whose initial edges are vertical is created. Cavern drop is more abrupt when the cavern top is filled partly with air. The contour of the piston is circular, as a circle is the shape such that the ratio between perimeter and area is minimal. In other cases, for instance in Kansas, the cavern rises until the uppermost keystone in the bedrock at shallow depth is breached, permitting loose materials to flow into the cavern through a relatively narrow hole at the bottom of the sink hole, as in an hour glass.

Organic solvent tolerance of an α-amylase from haloalkaliphilic bacteria as a function of pH, temperature, and salt concentrations.

PubMed

Pandey, Sandeep; Singh, S P

2012-04-01

A haloalkaliphilic bacterium was isolated from salt-enriched soil of Mithapur, Gujarat (India) and identified as Bacillus agaradhaerens Mi-10-6₂ based on 16S rRNA sequence analysis (NCBI gene bank accession, GQ121032). The bacterium was studied for its α-amylase characteristic in the presence of organic solvents. The enzyme was quite active and it retained considerable activity in 30% (v/v) organic solvents, dodecane, decane, heptane, n-hexane, methanol, and propanol. At lower concentrations of solvents, the catalysis was quite comparable to control. Enzyme catalysis at wide range of alkanes and alcohol was an interesting finding of the study. Mi-10-6₂ amylase retained activity over a broader alkaline pH range, with the optimal pH at 10-11. Two molars of salt was optimum for catalysis in the presence of most of the tested solvents, though the enzyme retained significant activity even at 4 M salt. With dodecane, the optimum temperature shifted from 50 °C to 60 °C, while the enzyme was active up to 80 °C. Over all, the present study focused on the effect of organic solvents on an extracellular α-amylase from haloalkaliphilic bacteria under varying conditions of pH, temperature, and salt.

The perception of low-salt bread among preschool children and the role of educational personnel in creating a positive attitude towards reformulated food.

PubMed

Kovac, Boris; Knific, Maja

2017-03-01

The purpose of this study was to identify the possibility of unnoticed reduction in salt content of bread as a basic food in the diet of preschool children. The response of children to less salty bread and the role of teachers and teacher assistants in the introduction of novelties into children's nutrition ware studied. Using hedonic sensory evaluation in the case of bread, the perception of salty taste and responses of preschool children to salt reduction were observed. The combination of quantitative and qualitative data analysis obtained from the case study group, composed of 22 preschool children and 66 teachers and teacher assistants, was studied. The results show that a 30% salt reduction was not registered by the children, while a 50% reduction of the salt content, compared to the original recipe, though noted, was not disruptive. The perception of taste and development of good eating habits at an early age could be influenced by teachers and teacher assistants' verbal and non-verbal communication. Salt reduction does not significantly affect the rating of satisfaction with the tested product. Educational personnel must be aware of their decisive influence on children's perception of new and less salty products. Such an approach could represent a basis for creating children's eating habits, which will be of particular importance later in their lives. The findings may possibly result in an update of the national nutrition policy.

Assessment of iodine concentration in dietary salt at household level in Morocco.

PubMed

Zahidi, Ahmed; Zahidi, Meriem; Taoufik, Jamal

2016-05-20

Following WHO recommendations, Morocco adopted in 1995 the universal salt iodization (USI) as a strategy to prevent and control iodine deficiency disorders. In 2009, the standard salt iodine concentration was adjusted to 15-40 mg/kg. The success of USI for the control of iodine deficiency disorders requires an evaluation of iodine concentration in salt prior to assessing the iodine nutritional status of a population. In our study we refer to the anterior studies that were made in Morocco in 1993 and 1998. 178 salt samples from households were tested for iodine using spot-testing kits. The iodometric titration method was used to analyze accurately the concentration of iodine in the 178 household salt samples. An empiric polling method was adopted, using a non-probability sampling method; across the different twelve regions in the country. The median and interquartile range iodine concentration in salt was 2.9 mg/kg (IQR: 2.4-3.7). The results show that only 25 % of households use iodized salt. The recommended iodine concentration in salt of 15-40 mg/kg was met only in 4.5 % of salt samples. The bulk salt is used by 8 % of households. All samples of this bulk salt were found in rural areas. According to nonparametric appropriate tests used, there is no significant difference in iodine concentrations between regions, between urban and rural areas and between packaged and bulk salt. Two decades since introducing legislation on Universal Salt Iodization, our survey shows that generalization of iodized salt is far from being reached. In 2015, only a quarter of Moroccan households use the iodized salt and only 4.5 % of salt is in conformity with regulations. The use of bulk salt by households in rural areas constitutes a major obstacle to the success of USI. The National Iodine Deficiency Disorders Control Program can only be achieved if an internal follow-up and a control of external quality of program is put in place.

Salt bridge as a gatekeeper against partial unfolding.

PubMed

Hinzman, Mark W; Essex, Morgan E; Park, Chiwook

2016-05-01

Salt bridges are frequently observed in protein structures. Because the energetic contribution of salt bridges is strongly dependent on the environmental context, salt bridges are believed to contribute to the structural specificity rather than the stability. To test the role of salt bridges in enhancing structural specificity, we investigated the contribution of a salt bridge to the energetics of native-state partial unfolding in a cysteine-free version of Escherichia coli ribonuclease H (RNase H*). Thermolysin cleaves a protruding loop of RNase H(*) through transient partial unfolding under native conditions. Lys86 and Asp108 in RNase H(*) form a partially buried salt bridge that tethers the protruding loop. Investigation of the global stability of K86Q/D108N RNase H(*) showed that the salt bridge does not significantly contribute to the global stability. However, K86Q/D108N RNase H(*) is greatly more susceptible to proteolysis by thermolysin than wild-type RNase H(*) is. The free energy for partial unfolding determined by native-state proteolysis indicates that the salt bridge significantly increases the energy for partial unfolding by destabilizing the partially unfolded form. Double mutant cycles with single and double mutations of the salt bridge suggest that the partially unfolded form is destabilized due to a significant decrease in the interaction energy between Lys86 and Asp108 upon partial unfolding. This study demonstrates that, even in the case that a salt bridge does not contribute to the global stability, the salt bridge may function as a gatekeeper against partial unfolding that disturbs the optimal geometry of the salt bridge. © 2016 The Protein Society.

Thermal energy storage material thermophysical property measurement and heat transfer impact

NASA Technical Reports Server (NTRS)

Tye, R. P.; Bourne, J. G.; Destarlais, A. O.

1976-01-01

The thermophysical properties of salts having potential for thermal energy storage to provide peaking energy in conventional electric utility power plants were investigated. The power plants studied were the pressurized water reactor, boiling water reactor, supercritical steam reactor, and high temperature gas reactor. The salts considered were LiNO3, 63LiOH/37 LiCl eutectic, LiOH, and Na2B4O7. The thermal conductivity, specific heat (including latent heat of fusion), and density of each salt were measured for a temperature range of at least + or - 100 K of the measured melting point. Measurements were made with both reagent and commercial grades of each salt.

40 CFR 471.31 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2014 CFR

2014-07-01

... TSS 95.6 45.5 pH (1) (1) 1 Within the range of 7.5 to 10.0 at all times. (w) Molten salt rinse... (pounds per million off-pounds) of nickel-cobalt treated with molten salt Chromium 3.72 1.52 Nickel 16.2...

40 CFR 471.31 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2012 CFR

2012-07-01

... TSS 95.6 45.5 pH (1) (1) 1 Within the range of 7.5 to 10.0 at all times. (w) Molten salt rinse... (pounds per million off-pounds) of nickel-cobalt treated with molten salt Chromium 3.72 1.52 Nickel 16.2...

40 CFR 471.31 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2013 CFR

2013-07-01

... TSS 95.6 45.5 pH (1) (1) 1 Within the range of 7.5 to 10.0 at all times. (w) Molten salt rinse... (pounds per million off-pounds) of nickel-cobalt treated with molten salt Chromium 3.72 1.52 Nickel 16.2...

RELATIONSHIPS OF NITROGEN LOADINGS, RESIDENTIAL DEVELOPMENT, AND PHYSICAL CHARACTERISTICS WITH PLANT STRUCTURE IN NEW ENGLAND SALT MARSHES

EPA Science Inventory

We examined the vascular plant species richness and the extent, density, and height of Spartina species of ten Narragansett Bay, Rhode Island (United States) fringe salt marshes which had a wide range of residential land development N-loadings associated with their watersheds. Si...

Active heat exchange system development for latent heat thermal energy storage

NASA Technical Reports Server (NTRS)

Lefrois, R. T.; Knowles, G. R.; Mathur, A. K.; Budimir, J.

1979-01-01

Active heat exchange concepts for use with thermal energy storage systems in the temperature range of 250 C to 350 C, using the heat of fusion of molten salts for storing thermal energy are described. Salt mixtures that freeze and melt in appropriate ranges are identified and are evaluated for physico-chemical, economic, corrosive and safety characteristics. Eight active heat exchange concepts for heat transfer during solidification are conceived and conceptually designed for use with selected storage media. The concepts are analyzed for their scalability, maintenance, safety, technological development and costs. A model for estimating and scaling storage system costs is developed and is used for economic evaluation of salt mixtures and heat exchange concepts for a large scale application. The importance of comparing salts and heat exchange concepts on a total system cost basis, rather than the component cost basis alone, is pointed out. The heat exchange concepts were sized and compared for 6.5 MPa/281 C steam conditions and a 1000 MW(t) heat rate for six hours. A cost sensitivity analysis for other design conditions is also carried out.

Flashback phenomenon and residual neurological deficits after the use of "bath salt" 3, 4- methylenedioxypyrovalerone.

PubMed

Mangold, Aaron R; Bravo, Thomas P; Traub, Stephen J; Maher, Steven A; Lipinski, Christopher A

2014-01-01

The use and abuse of designer drugs has been recognized for decades; however there are many derivatives of compounds that make their way into the community. Abuse of compound(s) known on the street as "bath salt" is on the rise. We report the case of a 33-year-old man who complained of "flashbacks" and right arm shaking that followed a night of "bath salt" snorting. The active compound methylenedioxypyrovalerone methamphetamine (MDPV) was confirmed; however, analysis of three different "bath salt" products showed difference in their active components. The patient's symptoms remained stable and he was discharged home after observation in the emergency department with instructions to return for any symptom progression. Practitioners should be aware of the abuse of the compounds and that not all "bath salt" products contain MDPV.

Salt, sodium chloride or sodium? Content and relationship with chemical, instrumental and sensory attributes in cooked meat products.

PubMed

Kameník, Josef; Saláková, Alena; Vyskočilová, Věra; Pechová, Alena; Haruštiaková, Danka

2017-09-01

The aim of this study was to determine the salt content in selected cooked meat products by the methods of determining the sodium content and the content of chlorides. The resulting data was compared with other chemical, instrumental and sensory parameters of the analysed samples. A total of 133 samples of 5 meat products were tested. The sodium content ranged from 558.0 to 1308.0mgNa/100g. Salt level determined by the two methods strongly correlated and did not differ in any meat product. Intensity of salty taste of the product was independent on its salt content. The salt (sodium) content may be reduced without a negative impact on sensory or instrumental properties of meat products. Copyright © 2017 Elsevier Ltd. All rights reserved.

Effects of SO42- ions on the corrosion of GH3535 weld joint in FLiNaK molten salt

NASA Astrophysics Data System (ADS)

Zhu, Yasheng; Qiu, Jie; Hou, Juan; Liu, Wenguan; Chen, Huaican; Ai, Hua; Yu, Guojun; Wang, Jianqiang; Zhou, Xingtai

2017-08-01

The present work studied the impact of SO42- ions on the corrosion behaviors of GH3535 weld joint in FLiNaK molten salt. The concentration of SO42- ions in the FLiNaK molten salt was controlled by adjusting the quantity of Na2SO4 added into the salt. Results indicate that the SO42- ions in the FLiNaK salt speed up the corrosion rate remarkably by promoting the dissolution of Cr from the alloy matrix into the salt. With the concentration of SO42- ions in the FLiNaK salt increases from 100 ppm to 1000 ppm, the weight losses and the Cr depletion layer depths of the corroded specimens increase linearly. Even in the case of the heavy corrosion attack caused by the SO42- ions, the corrosion performance is similar between the base zone and fusion zone in the GH3535 weld joint. It is demonstrated that the structural diversity caused by the welding process has little impact on the corrosion performances of GH3535 alloy in FLiNaK molten salt.

Context-driven Salt Seeking Test (Rats)

PubMed Central

Chang, Stephen E.; Smith, Kyle S.

2018-01-01

Changes in reward seeking behavior often occur through incremental learning based on the difference between what is expected and what actually happens. Behavioral flexibility of this sort requires experience with rewards as better or worse than expected. However, there are some instances in which behavior can change through non-incremental learning, which requires no further experience with an outcome. Such an example of non-incremental learning is the salt appetite phenomenon. In this case, animals such as rats will immediately seek out a highly-concentrated salt solution that was previously undesired when they are put in a novel state of sodium deprivation. Importantly, this adaptive salt-seeking behavior occurs despite the fact that the rats never tasted salt in the depleted state, and therefore never tasted it as a highly desirable reward. The following protocol is a method to investigate the neural circuitry mediating adaptive salt seeking using a conditioned place preference (CPP) procedure. The procedure is designed to provide an opportunity to discover possible dissociations between the neural circuitry mediating salt seeking and salt consumption to replenish the bodily deficit after sodium depletion. Additionally, this procedure is amenable to incorporating a number of neurobiological techniques for studying the brain basis of this behavior.

Present and future challenges of urban systems affected by seawater and its intrusion: the case of Venice, Italy

NASA Astrophysics Data System (ADS)

di Sipio, Eloisa; Zezza, Fulvio

2011-11-01

In lagoonal and marine environments, both historic monuments and recent buildings suffer from severe salt damage caused by sea flooding, sea-level rise and frequent storm events. Salt-water contamination of groundwater systems, a widespread phenomenon typical of coastal areas, can lead to a deterioration not only of the quality of fresh groundwater resources, but also of building materials in urban settlements. A general overview is given of the hydrogeological configuration of the subsoil of Venice (Italy), with particular reference to the shallow groundwater circulation. The relationship between the seawater in the subsoil and salt decay processes, due to salt crystallization, is highlighted. These processes affect civil constructions in Venice's historic center. Perched aquifers, influenced by tide variations and characterized by salt-water intrusion, favor the transport of salts within masonry walls through the action of rising damp. In fact, foundations, in direct contact with the aquifers, may become a preferential vehicle for the transportation of salt within buildings. Decay patterns of different building materials can be detected through non-destructive techniques, which can identify sea-salt damage and therefore assist in the preservation of cultural heritage in coastal areas.

Thermal-hydraulics of internally heated molten salts and application to the Molten Salt Fast Reactor

NASA Astrophysics Data System (ADS)

Fiorina, Carlo; Cammi, Antonio; Luzzi, Lelio; Mikityuk, Konstantin; Ninokata, Hisashi; Ricotti, Marco E.

2014-04-01

The Molten Salt Reactors (MSR) are an innovative kind of nuclear reactors and are presently considered in the framework of the Generation IV International Forum (GIF-IV) for their promising performances in terms of low resource utilization, waste minimization and enhanced safety. A unique feature of MSRs is that molten fluoride salts play the distinctive role of both fuel (heat source) and coolant. The presence of an internal heat generation perturbs the temperature field and consequences are to be expected on the heat transfer characteristics of the molten salts. In this paper, the problem of heat transfer for internally heated fluids in a straight circular channel is first faced on a theoretical ground. The effect of internal heat generation is demonstrated to be described by a corrective factor applied to traditional correlations for the Nusselt number. It is shown that the corrective factor can be fully characterized by making explicit the dependency on Reynolds and Prandtl numbers. On this basis, a preliminary correlation is proposed for the case of molten fluoride salts by interpolating the results provided by an analytic approach previously developed at the Politecnico di Milano. The experimental facility and the related measuring procedure for testing the proposed correlation are then presented. Finally, the developed correlation is used to carry out a parametric investigation on the effect of internal heat generation on the main out-of-core components of the Molten Salt Fast Reactor (MSFR), the reference circulating-fuel MSR design in the GIF-IV. The volumetric power determines higher temperatures at the channel wall, but the effect is significant only in case of large diameters and/or low velocities.

To Legislate or Not to Legislate? A Comparison of the UK and South African Approaches to the Development and Implementation of Salt Reduction Programs

PubMed Central

Charlton, Karen; Webster, Jacqui; Kowal, Paul

2014-01-01

The World Health Organization promotes salt reduction as a best-buy strategy to reduce chronic diseases, and Member States have agreed to a 30% reduction target in mean population salt intake by 2025. Whilst the UK has made the most progress on salt reduction, South Africa was the first country to pass legislation for salt levels in a range of processed foods. This paper compares the process of developing salt reduction strategies in both countries and highlights lessons for other countries. Like the UK, the benefits of salt reduction were being debated in South Africa long before it became a policy priority. Whilst salt reduction was gaining a higher profile internationally, undoubtedly, local research to produce context-specific, domestic costs and outcome indicators for South Africa was crucial in influencing the decision to legislate. In the UK, strong government leadership and extensive advocacy activities initiated in the early 2000s have helped drive the voluntary uptake of salt targets by the food industry. It is too early to say which strategy will be most effective regarding reductions in population-level blood pressure. Robust monitoring and transparent mechanisms for holding the industry accountable will be key to continued progress in each of the countries. PMID:25230210

Salt microspheres and potassium chloride usage for sodium reduction: Case study with sushi.

PubMed

Đorđević, Đani; Buchtová, Hana; Macharáčková, Blanka

2018-01-01

The aim of the study was to estimate possibilities of salt substitutes usage in the preparation of two sushi types (nigiri and maki) prepared with different seafood (salmon: Salmo salar, tuna: Thunnus albacares, and shrimp: Pleoticus muelleri). Potassium chloride (Mary samples), Soda-Lo (hollowed microsphere of regular salt crystals), and regular salt (sodium chloride) were used in the experiment. Sushi samples (n = 1960) were evaluated by 40 trained panelists who noticed that maki shrimp samples prepared with Mary salt had higher bitterness (21.48 ± 28.01) in comparison with 2% sodium chloride (7.91 ± 8.80). The saltiness was lower in nigiri tuna prepared with Mary (49.59 ± 17.47) than 2% sodium chloride (61.11 ± 15.75). The study clearly showed the possibility of lowering sodium content in sushi meal with the usage of salt substitutes, with emphasis that Soda-Lo should be considered as a better option due to the retention of sensory properties in sushi samples prepared with this salt substitute.

Effect of winds and waves on salt intrusion in the Pearl River estuary

NASA Astrophysics Data System (ADS)

Gong, Wenping; Lin, Zhongyuan; Chen, Yunzhen; Chen, Zhaoyun; Zhang, Heng

2018-02-01

Salt intrusion in the Pearl River estuary (PRE) is a dynamic process that is influenced by a range of factors and to date, few studies have examined the effects of winds and waves on salt intrusion in the PRE. We investigate these effects using the Coupled Ocean-Atmosphere-Wave-Sediment Transport (COAWST) modeling system applied to the PRE. After careful validation, the model is used for a series of diagnostic simulations. It is revealed that the local wind considerably strengthens the salt intrusion by lowering the water level in the eastern part of the estuary and increasing the bottom landward flow. The remote wind increases the water mixing on the continental shelf, elevates the water level on the shelf and in the PRE and pumps saltier shelf water into the estuary by Ekman transport. Enhancement of the salt intrusion is comparable between the remote and local winds. Waves decrease the salt intrusion by increasing the water mixing. Sensitivity analysis shows that the axial down-estuary wind, is most efficient in driving increases in salt intrusion via wind straining effect.

Improved Design and Fabrication of Hydrated-Salt Pills

NASA Technical Reports Server (NTRS)

Shirron, Peter J.; DiPirro, Michael J.; Canavan, Edgar R.

2011-01-01

A high-performance design, and fabrication and growth processes to implement the design, have been devised for encapsulating a hydrated salt in a container that both protects the salt and provides thermal conductance between the salt and the environment surrounding the container. The unitary salt/container structure is known in the art as a salt pill. In the original application of the present design and processes, the salt is, more specifically, a hydrated paramagnetic salt, for use as a refrigerant in a very-low-temperature adiabatic demagnetization refrigerator (ADR). The design and process can also be applied, with modifications, to other hydrated salts. Hydrated paramagnetic salts have long been used in ADRs because they have the desired magnetic properties at low temperatures. They also have some properties, disadvantageous for ADRs, that dictate the kind of enclosures in which they must be housed: Being hydrated, they lose water if exposed to less than 100-percent relative humidity. Because any dehydration compromises their magnetic properties, salts used in ADRs must be sealed in hermetic containers. Because they have relatively poor thermal conductivities in the temperature range of interest (<0.1 K), integral thermal buses are needed as means of efficiently transferring heat to and from the salts during refrigeration cycles. A thermal bus is typically made from a high-thermal-conductivity met al (such as copper or gold), and the salt is configured to make intimate thermal contact with the metal. Commonly in current practice (and in the present design), the thermal bus includes a matrix of wires or rods, and the salt is grown onto this matrix. The density and spacing of the conductors depend on the heat fluxes that must be accommodated during operation.

Using growth-based methods to determine direct effects of salinity on soil microbial communities

NASA Astrophysics Data System (ADS)

Rath, Kristin; Rousk, Johannes

2015-04-01

Soil salinization is a widespread agricultural problem and increasing salt concentrations in soils have been found to be correlated with decreased microbial activity. A central challenge in microbial ecology is to link environmental factors, such as salinity, to responses in the soil microbial community. That is, it can be difficult to distinguish direct from indirect effects. In order to determine direct salinity effects on the community we employed the ecotoxicological concept of Pollution-Induced Community Tolerance (PICT). This concept is built on the assumption that if salinity had an ecologically relevant effect on the community, it should have selected for more tolerant species and strains, resulting in an overall higher community tolerance to salt in communities from saline soils. Growth-based measures, such as the 3H-leucine incorporation into bacterial protein , provide sensitive tools to estimate community tolerance. They can also provide high temporal resolution in tracking changes in tolerance over time. In our study we used growth-based methods to investigate: i) at what levels of salt exposure and over which time scales salt tolerance can be induced in a non-saline soil, and (ii) if communities from high salinity sites have higher tolerance to salt exposure along natural salinity gradients. In the first part of the study, we exposed a non-saline soil to a range of salinities and monitored the development of community tolerance over time. We found that community tolerance to intermediate salinities up to around 30 mg NaCl per g soil can be induced at relatively short time scales of a few days, providing evidence that microbial communities can adapt rapidly to changes in environmental conditions. In the second part of the study we used soil samples originating from natural salinity gradients encompassing a wide range of salinity levels, with electrical conductivities ranging from 0.1 dS/m to >10 dS/m. We assessed community tolerance to salt by measuring the bacterial growth response to added NaCl in a soil suspension. The bacterial community tolerance to salt increased along the salt gradients with higher in situ soil salinity. In samples from the low-saline end of the gradient, bacterial growth rates in the soil suspension showed a clear concentration-response relationship to NaCl resulting in inhibition curves. This relationship gradually changed toward higher salt concentrations. In soil samples from high salinity sites, bacterial growth was no longer inhibited by adding high concentrations of NaCl to the bacterial soil suspension. In fact, adding NaCl even promoted bacterial growth rates. These results show that salinity played an ecologically significant role in shaping communities at the highly saline end of the gradients and provide evidence for a direct salt effect on the microbial community

Effect of salt intake on beat-to-beat blood pressure nonlinear dynamics and entropy in salt-sensitive versus salt-protected rats.

PubMed

Fares, Souha A; Habib, Joseph R; Engoren, Milo C; Badr, Kamal F; Habib, Robert H

2016-06-01

Blood pressure exhibits substantial short- and long-term variability (BPV). We assessed the hypothesis that the complexity of beat-to-beat BPV will be differentially altered in salt-sensitive hypertensive Dahl rats (SS) versus rats protected from salt-induced hypertension (SSBN13) maintained on high-salt versus low-salt diet. Beat-to-beat systolic and diastolic BP series from nine SS and six SSBN13 rats (http://www.physionet.org) were analyzed following 9 weeks on low salt and repeated after 2 weeks on high salt. BP complexity was quantified by detrended fluctuation analysis (DFA), short- and long-range scaling exponents (αS and αL), sample entropy (SampEn), and traditional standard deviation (SD) and coefficient of variation (CV(%)). Mean systolic and diastolic BP increased on high-salt diet (P < 0.01) particularly for SS rats. SD and CV(%) were similar across groups irrespective of diet. Salt-sensitive and -protected rats exhibited similar complexity indices on low-salt diet. On high salt, (1) SS rats showed increased scaling exponents or smoother, systolic (P = 0.007 [αL]) and diastolic (P = 0.008 [αL]) BP series; (2) salt-protected rats showed lower SampEn (less complex) systolic and diastolic BP (P = 0.046); and (3) compared to protected SSBN13 rats, SS showed higher αL for systolic (P = 0.01) and diastolic (P = 0.005) BP Hypertensive SS rats are more susceptible to high salt with a greater rise in mean BP and reduced complexity. Comparable mean pressures in sensitive and protective rats when on low-salt diet coupled with similar BPV dynamics suggest a protective role of low-salt intake in hypertensive rats. This effect likely reflects better coupling of biologic oscillators. © 2016 The Authors. Physiological Reports published by Wiley Periodicals, Inc. on behalf of the American Physiological Society and The Physiological Society.

Guanidinium can both Cause and Prevent the Hydrophobic Collapse of Biomacromolecules

PubMed Central

2017-01-01

A combination of Fourier transform infrared and phase transition measurements as well as molecular computer simulations, and thermodynamic modeling were performed to probe the mechanisms by which guanidinium (Gnd+) salts influence the stability of the collapsed versus uncollapsed state of an elastin-like polypeptide (ELP), an uncharged thermoresponsive polymer. We found that the cation’s action was highly dependent upon the counteranion with which it was paired. Specifically, Gnd+ was depleted from the ELP/water interface and was found to stabilize the collapsed state of the macromolecule when paired with well-hydrated anions such as SO42–. Stabilization in this case occurred via an excluded volume (or depletion) effect, whereby SO42– was strongly partitioned away from the ELP/water interface. Intriguingly, at low salt concentrations, Gnd+ was also found to stabilize the collapsed state of the ELP when paired with SCN–, which is a strong binder for the ELP. In this case, the anion and cation were both found to be enriched in the collapsed state of the polymer. The collapsed state was favored because the Gnd+ cross-linked the polymer chains together. Moreover, the anion helped partition Gnd+ to the polymer surface. At higher salt concentrations (>1.5 M), GndSCN switched to stabilizing the uncollapsed state because a sufficient amount of Gnd+ and SCN– partitioned to the polymer surface to prevent cross-linking from occurring. Finally, in a third case, it was found that salts which interacted in an intermediate fashion with the polymer (e.g., GndCl) favored the uncollapsed conformation at all salt concentrations. These results provide a detailed, molecular-level, mechanistic picture of how Gnd+ influences the stability of polypeptides in three distinct physical regimes by varying the anion. It also helps explain the circumstances under which guanidinium salts can act as powerful and versatile protein denaturants. PMID:28054487

The iodized salt programme in Bangalore, India provides adequate iodine intakes in pregnant women and more-than-adequate iodine intakes in their children.

PubMed

Jaiswal, Nidhi; Melse-Boonstra, Alida; Sharma, Surjeet Kaur; Srinivasan, Krishnamachari; Zimmermann, Michael B

2015-02-01

To compare the iodine status of pregnant women and their children who were sharing all meals in Bangalore, India. A cross-sectional study evaluating demographic characteristics, household salt iodine concentration and salt usage patterns, urinary iodine concentrations (UIC) in women and children, and maternal thyroid volume (ultrasound). Antenatal clinic of an urban tertiary-care hospital, which serves a low-income population. Healthy pregnant women in all trimesters, aged 18-35 years, who had healthy children aged 3-15 years. Median (range) iodine concentrations of household powdered and crystal salt were 55·9 (17·2-65·9) ppm and 18·9 (2·2-68·2) ppm, respectively. The contribution of iodine-containing supplements and multi-micronutrient powders to iodine intake in the families was negligible. Adequately iodized salt, together with small amounts of iodine in local foods, were providing adequate iodine during pregnancy: (i) the overall median (range) UIC in women was 172 (5-1024) µg/l; (ii) the median UIC was >150 µg/l in all trimesters; and (iii) thyroid size was not significantly different across trimesters. At the same time, the median (range) UIC in children was 220 (10-782) µg/l, indicating more-than-adequate iodine intake at this age. Median UIC was significantly higher in children than in their mothers (P=0·008). In this selected urban population of southern India, the iodized salt programme provides adequate iodine to women throughout pregnancy, at the expense of higher iodine intake in their children. Thus we suggest that the current cut-off for median UIC in children indicating more-than-adequate intake, recommended by the WHO/UNICEF/International Council for the Control of Iodine Deficiency Disorders may, need to be reconsidered.

Dietary flexibility in three representative waterbirds across salinity and depth gradients in salt ponds of San Francisco Bay

USGS Publications Warehouse

Takekawa, John Y.; Miles, A.K.; Tsao-Melcer, D. C.; Schoellhamer, D.H.; Fregien, S.; Athearn, N.D.

2009-01-01

Salt evaporation ponds have existed in San Francisco Bay, California, for more than a century. In the past decade, most of the salt ponds have been retired from production and purchased for resource conservation with a focus on tidal marsh restoration. However, large numbers of waterbirds are found in salt ponds, especially during migration and wintering periods. The value of these hypersaline wetlands for waterbirds is not well understood, including how different avian foraging guilds use invertebrate prey resources at different salinities and depths. The aim of this study was to investigate the dietary flexibility of waterbirds by examining the population number and diet of three feeding guilds across a salinity and depth gradient in former salt ponds of the Napa-Sonoma Marshes. Although total invertebrate biomass and species richness were greater in low than high salinity salt ponds, waterbirds fed in ponds that ranged from low (20 g l-1) to very high salinities (250 g l -1). American avocets (surface sweeper) foraged in shallow areas at pond edges and consumed a wide range of prey types (8) including seeds at low salinity, but preferred brine flies at mid salinity (40-80 g l-1). Western sandpipers (prober) focused on exposed edges and shoal habitats and consumed only a few prey types (2-4) at both low and mid salinities. Suitable depths for foraging were greatest for ruddy ducks (diving benthivore) that consumed a wide variety of invertebrate taxa (5) at low salinity, but focused on fewer prey (3) at mid salinity. We found few brine shrimp, common in higher salinity waters, in the digestive tracts of any of these species. Dietary flexibility allows different guilds to use ponds across a range of salinities, but their foraging extent is limited by available water depths. ?? 2009 USGS, US Government.

Influence of dilution water ionic composition on acute major ion toxicity to the mayfly Neocloeon triangulifer.

PubMed

Soucek, David J; Mount, David R; Dickinson, Amy; Hockett, J Russell

2018-05-01

Field and laboratory studies have shown that mayflies (Ephemeroptera) tend to be relatively sensitive to elevated major ion concentrations, but little is known about how ionic composition influences these responses. The present study evaluated the acute toxicity of major ion salts to the mayfly Neocloeon triangulifer over a range of background water quality conditions. The mayfly was particularly sensitive to Na 2 SO 4 , with the median lethal concentration (LC50) of 1338 mg SO 4 /L being lower than LC50s reported for 7 other species at that hardness. Increasing hardness of the dilution water from 30 to 150 mg/L (as CaCO 3 ) resulted in doubling of LC50s for sodium salts, and an approximately 1.5-fold increase in LC50 for MgSO 4 . Potassium salt toxicity was not strongly influenced by hardness, consistent with findings for other species. When hardness was held constant but the Ca to Mg ratio was manipulated, the ameliorative effect on Na 2 SO 4 and NaCl did not appear as strong as when hardness was varied; but for MgSO 4 the amelioration relative to Ca activity was similar between the 2 experiments. The toxicity of K salts to N. triangulifer was similar to Na salts on a millimolar basis, which contrasts with several other species for which K salts have been much more toxic. In addition, the toxicity of KCl to N. triangulifer was not notably affected by Na concentration, as has been shown for Ceriodaphnia dubia. Finally, plotting LC50s in terms of ion activity (Cl, SO 4 , Na, Mg, or K) over the range of Ca activities in dilution water resulted in significant positive relationships, with comparable slopes to those previously observed for C. dubia over the same range of Ca activities. Environ Toxicol Chem 2018;37:1330-1339. © 2018 SETAC. © 2018 SETAC.

Process for converting sodium nitrate-containing, caustic liquid radioactive wastes to solid insoluble products

DOEpatents

Barney, Gary S.; Brownell, Lloyd E.

1977-01-01

A method for converting sodium nitrate-containing, caustic, radioactive wastes to a solid, relatively insoluble, thermally stable form is provided and comprises the steps of reacting powdered aluminum silicate clay, e.g., kaolin, bentonite, dickite, halloysite, pyrophyllite, etc., with the sodium nitrate-containing radioactive wastes which have a caustic concentration of about 3 to 7 M at a temperature of 30.degree. C to 100.degree. C to thereby entrap the dissolved radioactive salts in the aluminosilicate matrix. In one embodiment the sodium nitrate-containing, caustic, radioactive liquid waste, such as neutralized Purex-type waste, or salts or oxide produced by evaporation or calcination of these liquid wastes (e.g., anhydrous salt cake) is converted at a temperature within the range of 30.degree. C to 100.degree. C to the solid mineral form-cancrinite having an approximate chemical formula 2(NaAlSiO.sub.4) .sup.. xSalt.sup.. y H.sub.2 O with x = 0.52 and y = 0.68 when the entrapped salt is NaNO.sub.3. In another embodiment the sodium nitrate-containing, caustic, radioactive liquid is reacted with the powdered aluminum silicate clay at a temperature within the range of 30.degree. C to 100.degree. C, the resulting reaction product is air dried eitheras loose powder or molded shapes (e.g., bricks) and then fired at a temperature of at least 600.degree. C to form the solid mineral form-nepheline which has the approximate chemical formula of NaAlSiO.sub.4. The leach rate of the entrapped radioactive salts with distilled water is reduced essentially to that of the aluminosilicate lattice which is very low, e.g., in the range of 10.sup.-.sup.2 to 10.sup.-.sup.4 g/cm.sup.2 -- day for cancrinite and 10.sup.-.sup.3 to 10.sup.-.sup.5 g/cm.sup.2 -- day for nepheline.

Potential of duckweed (Lemna minor) for removal of nitrogen and phosphorus from water under salt stress.

PubMed

Liu, Chunguang; Dai, Zheng; Sun, Hongwen

2017-02-01

Duckweed plays a major role in the removal of nitrogen (N) and phosphorus (P) from water. To determine the effect of salt stress on the removal of N and P by duckweed, we cultured Lemna minor, a common species of duckweed, in N and P-rich water with NaCl concentrations ranging from 0 to 100 mM for 24 h and 72 h, respectively. The results show that the removal capacity of duckweed for N and P was reduced by salt stress. Higher salt stress with longer cultivation period exerts more injury to duckweed and greater inhibition of N and P removal. Severe salt stress (100 mM NaCl) induced duckweed to release N and P and even resulted in negative removal efficiencies. The results indicate that L. minor should be used to remove N and P from water with salinities below 75 mM NaCl, or equivalent salt stress. Copyright © 2016 Elsevier Ltd. All rights reserved.

Proposed method of hydrogeochemical exploration for salt deposits using ClBr ratios, Eastern Province, Kingdom of Saudi Arabia

USGS Publications Warehouse

Smith, C.L.

1991-01-01

Despite the value of the salt (NaCl) and brine used by the chemical industry, geochemical prospecting techniques are not customarily employed in the search for these raw materials. In this study, Br geochemistry is used as the basis for a proposed hydrogeochemical prospecting technique that was designed to search for shallow halite beds in the Eastern Province of the Kingdom of Saudi Arabia. Near-surface brine samples were collected at Sabkhah Jayb Uwayyid, both directly above and distant from a buried salt bed. Brine samples collected both directly above and offset to the north-west of the salt bed had ClBr ratios > 8000. The regional background ClBr ratio of fresh nonmarime ground water is ???300. The large range in ClBr ratios and the association of high ClBr ratios with the buried salt body suggest that the ratio can be useful in hydrogeochemical prospecting for sibakh-associated, shallow salt bodies. ?? 1991.

Soil processes evolved by the establishment of tree plantations on croplands/grasslands - evaluation of afforestation effect on the Great Plain (Hungary)

NASA Astrophysics Data System (ADS)

Balog, Kitti; Szabó, András; Gribovszki, Zoltán; Tóth, Tibor

2016-04-01

In Hungary, there was a great increase in the acreage of forested areas during the last century (1.1 to 1.8 million ha). Most of the plantations were established on non-profitable grasslands/croplands (National Forest Strategy, 2009). The forests affect hydrologic and climatic elements of the physical habitat and induce alterations in the soil properties, as well. Soil and groundwater of 70 plantations (Poplar, Common oak and Black locust) and nearby control plots (grassland/cropland) - representing former land use - were investigated over the Great Hungarian Plain. Sampling sites were located by a gradient of climatic water balance, initial water table depth and salinity, soil layering, tree species and plantation age. Short- and long-term effects in groundwater levels (GWL) were found under the woody vegetation. GWL depression evolved beneath forests (poplar and oak provably) compared to control, in 78.8% of the cases. GWL depression was the most significant in the growing season, then the difference between GWLs decreased. Since evapotranspiration (ET) is the main driving force for water consumption of trees, and the ET of trees can be three times higher than that of the grassy control in the growing season, greater (ground)water uptake could be measured, giving rise to higher GWL depression. Short-term effect of the plantation was the daily fluctuation of GWL in the woods that can be twice as much as that of the control. Water uptake is influenced by the type of the groundwater zone (recharge/discharge), where the sample area is located, and by tree species (diverse water demands). Afforestation raised the salt content of the groundwater slightly. In 52.9 % of the cases, salt content of groundwater was higher under the forest, than under the control. Below the forests, salts concentrated in the soil profile and formed a salt accumulation zone surrounding the root zone. In 52.9 % of the cases, salts accumulated in the profile: in the subsoil under the trees (3.7-4.3 m) and in the upper soil (0-1.5 m) under the grassy areas. Subsurface salt accumulation is generated by the water uptake of trees from salty groundwater due to the ion exclusion of tree roots. Plantation age and biomass are the factors enhancing salt accumulation, according to growth rate of the tree species. Differences between the soil salt content of the woody and grassy vegetation along the whole profile (from ground to water level) showed decreasing salt accumulation in the order of Poplar > Common oak > Black locust (0,0484; 0,0304 and 0,0246 dS/m, respectively). The rate of accumulation tends to be slight due to the infiltration of precipitation during the rest period of the deciduous forests that leaches the salts from the profile each year, preventing high rate of salt accumulation. This research was supported by OTKA NN 79835 project and Postdoctoral Research Program of HAS No. PD-029/2015.

Freezing points and small-scale deicing tests for salts of levulinic acid made from grain sorghum.

PubMed

Ganjyal, G; Fang, Q; Hanna, M A

2007-11-01

Deicers from renewable resources are needed to overcome the disadvantages of using traditional deicers. Salts made from levulinic acid produced using grain sorghum as raw material were tested as road deicing agents. Freezing points of these salts viz., sodium levulinate, magnesium levulinate and calcium levulinate along with rock salt (sodium chloride) were determined according to American Society for Testing and Materials (ASTM) D 1177-94 standard at concentrations of 10, 20, 30 and 40 % w/w. There were significant differences among the freezing points of the salts. Freezing points for rock salt, sodium levulinate, calcium levulinate and magnesium levulinate, for different concentrations, were in the ranges of -6.6 to -20.5, -2.9 to -15.0, -2.1 to -7.8 and -1.5 to -6.5 degrees C, respectively. Deicing effectiveness of the salts of levulinic acid were investigated by conducting small-scale deicing tests with aqueous solutions of various salt concentrations (2%, 5% and 10%) in a laboratory freezer and by spraying the deicer on a graveled surface covered by ice and snow with the average temperature during the testing at -2.7 degrees C. Deicing capabilities of the three salts of levulinic acid differed. At -2.7 degrees C, all three salts caused melting of the ice. Among the different levulinates studied sodium levulinate was the most effective deicing agent. These salts of levulinates could be a viable replacement for traditional deicers and could help in reducing the disadvantages of traditional deicers.

Aerosol analysis and forecast in the European Centre for Medium-Range Weather Forecasts Integrated Forecast System: 3. Evaluation by means of case studies

NASA Astrophysics Data System (ADS)

Mangold, A.; de Backer, H.; de Paepe, B.; Dewitte, S.; Chiapello, I.; Derimian, Y.; Kacenelenbogen, M.; LéOn, J.-F.; Huneeus, N.; Schulz, M.; Ceburnis, D.; O'Dowd, C.; Flentje, H.; Kinne, S.; Benedetti, A.; Morcrette, J.-J.; Boucher, O.

2011-02-01

A near real-time system for assimilation and forecasts of aerosols, greenhouse and trace gases, extending the ECMWF Integrated Forecasting System (IFS), has been developed in the framework of the Global and regional Earth-system Monitoring using Satellite and in-situ data (GEMS) project. The GEMS aerosol modeling system is novel as it is the first aerosol model fully coupled to a numerical weather prediction model with data assimilation. A reanalysis of the period 2003-2009 has been carried out with the same system. During its development phase, the aerosol system was first run for the time period January 2003 to December 2004 and included sea salt, desert dust, organic matter, black carbon, and sulfate aerosols. In the analysis, Moderate Resolution Imaging Spectroradiometer (MODIS) total aerosol optical depth (AOD) at 550 nm over ocean and land (except over bright surfaces) was assimilated. This work evaluates the performance of the aerosol system by means of case studies. The case studies include (1) the summer heat wave in Europe in August 2003, characterized by forest fire aerosol and conditions of high temperatures and stagnation, favoring photochemistry and secondary aerosol formation, (2) a large Saharan dust event in March 2004, and (3) periods of high and low sea salt aerosol production. During the heat wave period in 2003, the linear correlation coefficients between modeled and observed AOD (550 nm) and between modeled and observed PM2.5 mass concentrations are 0.82 and 0.71, respectively, for all investigated sites together. The AOD is slightly and the PM2.5 mass concentration is clearly overestimated by the aerosol model during this period. The simulated sulfate mass concentration is significantly correlated with observations but is distinctly overestimated. The horizontal and vertical locations of the main features of the aerosol distribution during the Saharan dust outbreak are generally well captured, as well as the timing of the AOD peaks. The aerosol model simulates winter sea salt AOD reasonably well, however, showing a general overestimation. Summer sea salt events show a better agreement. Overall, the assimilation of MODIS AOD data improves the subsequent aerosol predictions when compared with observations, in particular concerning the correlation and AOD peak values. The assimilation is less effective in correcting a positive (PM2.5, sulfate mass concentration, Angström exponent) or negative (desert dust plume AOD) model bias.

Corrosion of SiC by Molten Salt

NASA Technical Reports Server (NTRS)

Jacobson, Nathan S.; Smialek, James L.

1987-01-01

Advanced ceramic materials considered for wide range of applications as in gas turbine engines and heat exchangers. In such applications, materials may be in corrosive environments that include molten salts. Very corrosive to alloys. In order to determine extent of problem for ceramic materials, corrosion of SiC by molten salts studied in both jet fuel burners and laboratory furnaces. Surface of silicon carbide corroded by exposure to flame seeded with 4 parts per million of sodium. Strength of silicon carbide decreased by corrosion in flame and tube-furnace tests.

Multiplex CARS spectroscopy of Rochelle salt crystal

NASA Astrophysics Data System (ADS)

Hadjichristov, G. B.; Kircheva, P. P.; Kirov, N.

1996-08-01

An optical four-wave mixing (FWM) described by the nonlinear susceptibility x(3) ( ωas = 2 ωp - ωs) is studied in a single crystal of Rochelle salt (NaKC 4H 4O 6·H 2O). In addition to the coherent anti-Stokes Raman Scattering (CARS) structure, the FWM spectra consist of nonvibrational (background) components. After analysis of the FWM spectra in the range from 1100 to 1450 cm -1, the nonresonant (electronic) susceptibility elements xelzzzz and xelxxxx of Rochelle salt single crystal are estimated.

Deposition or not? The fate of volcanic ash after aggregation processes

NASA Astrophysics Data System (ADS)

Mueller, Sebastian B.; Kueppers, Ulrich; Wadsworth, Fabian B.; Ayris, Paul M.; Casas, Ana S.; Cimarelli, Corrado; Ametsbichler, Jonathan; Delmelle, Pierre; Taddeucci, Jacopo; Jacob, Michael; Dingwell, Donald B.

2017-04-01

In the course of explosive volcanic eruptions, large amounts of ash are released into the atmosphere and may subsequently pose a threat to infrastructure, such as aviation industry. Ash plume forecasting is therefore a crucial tool for volcanic hazard mitigation but may be significantly affected by aggregation, altering the aerodynamic properties of particles. Models struggle with the implementation of aggregation since external conditions promoting aggregation have not been completely understood; in a previous study we have shown the rapid generation of ash aggregates through liquid bonding via the use of fluidization bed technology and further defined humidity and temperature ranges necessary to trigger aggregation. Salt (NaCl) was required for the recovery of stable aggregates, acting as a cementation agent and granting aggregate cohesion. A numerical model was used to explain the physics behind particle aggregation mechanisms and further predicted a dependency of aggregation efficiency on liquid binder viscosity. In this study we proof the effect of viscosity on particle aggregation. HCl and H2SO4 solutions were diluted to various concentrations resulting in viscosities between 1 and 2 mPas. Phonolitic and rhyolitic ash samples as well as soda-lime glass beads (serving as analogue material) were fluidized in the ProCell Lab® of Glatt Ingenieurtechnik GmbH and treated with the acids via a bottom-spray technique. Chemically driven interaction between acid liquids and surfaces of the three used materials led to crystal precipitation. Salt crystals (e.g. NaCl) have been confirmed through scanning electron microscopy (SEM) and leachate analysis. Both volcanic ash samples as well as the glass beads showed a clear dependency of aggregation efficiency on viscosity of the sprayed HCl solution. Spraying H2SO4 provoked a collapse of the fluidized bed and no aggregation has been observed. This is accounted by the high hygroscopicity of H2SO4. Dissolving CaCl2 (known to be a highly hygroscopic salt) in de-ionized water yielded comparable results without observable aggregation. In case of successful aggregation, concentration of salts has been found to be in the range of published values. We conclude that non-hygroscopic salt crystal precipitation from an aqueous liquid interacting with the glass phase in volcanic ash is a very efficient way to produce cohesive ash aggregates that can survive external forces acting during transport and sedimentation. Our parameterization of ash aggregation processes shall now be implemented in ash plume dispersal modelling for improved and more accurate ash distribution forecasting in the event of explosive volcanic eruptions.

Know Your Noodles! Assessing Variations in Sodium Content of Instant Noodles across Countries.

PubMed

Farrand, Clare; Charlton, Karen; Crino, Michelle; Santos, Joseph; Rodriguez-Fernandez, Rodrigo; Ni Mhurchu, Cliona; Webster, Jacqui

2017-06-16

Reducing salt intake is a cost-effective public health intervention to reduce the global burden of non-communicable disease (NCDs). Ultra-processed foods contribute ~80% of dietary salt in high income countries, and are becoming prominent in low-middle income countries. Instant noodle consumption is particularly high in the Asia Pacific region. The aim of this study was to compare the sodium content of instant noodles sold worldwide to identify potential for reformulation. Analysis was undertaken for 765 instant noodle products from 10 countries using packaged food composition databases of ultra-processed foods compiled by the Global Food Monitoring Group (GFMG) and national shop survey data. Sodium levels were high and variable, within and between countries. Instant noodles in China had the highest mean sodium content (1944 mg/100 g; range: 397-3678/100 g) compared to New Zealand (798 mg/100 g; range: 249-2380 mg/100 g). Average pack size ranged from 57 g (Costa Rica) to 98 g (China). The average packet contributed 35% to 95% of the World Health Organization recommended daily salt intake of <5 g. Forty-one percent of products met the Pacific Island (PICs) regional sodium targets, 37% met the South Africa 2016 targets, and 62% met the UK 2017 targets. This study emphasises a need for stronger regulation and closer monitoring to drive rigorous reformulation of salt in ultra-processed foods.

Know Your Noodles! Assessing Variations in Sodium Content of Instant Noodles across Countries

PubMed Central

Farrand, Clare; Charlton, Karen; Crino, Michelle; Santos, Joseph; Rodriguez-Fernandez, Rodrigo; Ni Mhurchu, Cliona; Webster, Jacqui

2017-01-01

Reducing salt intake is a cost-effective public health intervention to reduce the global burden of non-communicable disease (NCDs). Ultra-processed foods contribute ~80% of dietary salt in high income countries, and are becoming prominent in low-middle income countries. Instant noodle consumption is particularly high in the Asia Pacific region. The aim of this study was to compare the sodium content of instant noodles sold worldwide to identify potential for reformulation. Analysis was undertaken for 765 instant noodle products from 10 countries using packaged food composition databases of ultra-processed foods compiled by the Global Food Monitoring Group (GFMG) and national shop survey data. Sodium levels were high and variable, within and between countries. Instant noodles in China had the highest mean sodium content (1944 mg/100 g; range: 397–3678/100 g) compared to New Zealand (798 mg/100 g; range: 249–2380 mg/100 g). Average pack size ranged from 57 g (Costa Rica) to 98 g (China). The average packet contributed 35% to 95% of the World Health Organization recommended daily salt intake of <5 g. Forty-one percent of products met the Pacific Island (PICs) regional sodium targets, 37% met the South Africa 2016 targets, and 62% met the UK 2017 targets. This study emphasises a need for stronger regulation and closer monitoring to drive rigorous reformulation of salt in ultra-processed foods. PMID:28621720

Study of constraints in using household NaCl salt for retrospective dosimetry

NASA Astrophysics Data System (ADS)

Elashmawy, M.

2018-05-01

Thermoluminescence (TL) characteristics of 5 different household NaCl salts and one analytical salt were determined to investigate the possible factors that affect the reliability of using household salt for retrospective dosimetry. Salts' TL sensitivities were found to be particle-size dependent and approached saturation at the largest size, whereas for salts that have the same particle size, the TL sensitivity depended on their origin. TL dependence on the particle size interprets significant variations in TL response reported in the literature for the same salt patch. The first TL readout indicated that all salts have similar glow curves with one distinctive peak. Typical second TL readout at two different doses showed a dramatic decrease in TL sensitivity associated with a significant change in the glow curve structure possessing two prominent peaks. Glow curve deconvolution (GCD) of the first TL readout for all salts yielded 6 individual glow peaks of first-order kinetics, whereas in GCD of second TL readouts, 5 individual glow peaks of second-order kinetics were obtained. Similarities in the glow curve structures of the first and second TL readouts suggest that additives such as KIO3 and MgCO3 have no effect on the TL process. Fading effect was evaluated for the salt of highest TL sensitivity, and it was found that the integral TL intensity decreased gradually and lost 40% of its initial value over 2 weeks, after which it remained constant. Results conclude that a household salt cannot be used for retrospective dosimetry without considering certain constraints such as the salt's origin and particle size. Furthermore, preparedness for radiological accidents and accurate dose reconstructions require that most of the commonly distributed household salt brands should be calibrated in advance and stored in a repository to be recalled in case of accidents.

Three Mountain Areas in Southwestern Wyoming.

DTIC Science & Technology

purpose of this report the areas are called the Wyoming-Salt River Range Area, the Wind River Range Area, and the Uinta Range Area. These mountain...ranges enclose the Upper Green River and Bridger Basins , high plateau basins with a general elevation of 6,500 to 7,500 feet.

Salt Inactivates Endothelial Nitric Oxide Synthase in Endothelial Cells12

PubMed Central

Li, Juan; White, James; Guo, Ling; Zhao, Xiaomin; Wang, Jiafu; Smart, Eric J.; Li, Xiang-An

2009-01-01

There is a 1–4 mmol/L rise in plasma sodium concentrations in individuals with high salt intake and in patients with essential hypertension. In this study, we used 3 independent assays to determine whether such a small increase in sodium concentrations per se alters endothelial nitric oxide synthase (eNOS) function and contributes to hypertension. By directly measuring NOS activity in living bovine aortic endothelial cells, we demonstrated that a 5-mmol/L increase in salt concentration (from 137 to 142 mmol/L) caused a 25% decrease in NOS activity. Importantly, the decrease in NOS activity was in a salt concentration-dependent manner. The NOS activity was decreased by 25, 45, and 70%, with the increase of 5, 10, and 20 mmol/L of NaCl, respectively. Using Chinese hamster ovary cells stably expressing eNOS, we confirmed the inhibitory effects of salt on eNOS activity. The eNOS activity was unaffected in the presence of equal milliosmol of mannitol, which excludes an osmotic effect. Using an ex vivo aortic angiogenesis assay, we demonstrated that salt attenuated the nitric oxide (NO)-dependent proliferation of endothelial cells. By directly monitoring blood pressure changes in response to salt infusion, we found that in vivo infusion of salt induced an acute increase in blood pressure in a salt concentration-dependent manner. In conclusion, our findings demonstrated that eNOS is sensitive to changes in salt concentration. A 5-mmol/L rise in salt concentration, within the range observed in essential hypertension patients or in individuals with high salt intake, could significantly suppress eNOS activity. This salt-induced reduction in NO generation in endothelial cells may contribute to the development of hypertension. PMID:19176751

Salt inactivates endothelial nitric oxide synthase in endothelial cells.

PubMed

Li, Juan; White, James; Guo, Ling; Zhao, Xiaomin; Wang, Jiafu; Smart, Eric J; Li, Xiang-An

2009-03-01

There is a 1-4 mmol/L rise in plasma sodium concentrations in individuals with high salt intake and in patients with essential hypertension. In this study, we used 3 independent assays to determine whether such a small increase in sodium concentrations per se alters endothelial nitric oxide synthase (eNOS) function and contributes to hypertension. By directly measuring NOS activity in living bovine aortic endothelial cells, we demonstrated that a 5-mmol/L increase in salt concentration (from 137 to 142 mmol/L) caused a 25% decrease in NOS activity. Importantly, the decrease in NOS activity was in a salt concentration-dependent manner. The NOS activity was decreased by 25, 45, and 70%, with the increase of 5, 10, and 20 mmol/L of NaCl, respectively. Using Chinese hamster ovary cells stably expressing eNOS, we confirmed the inhibitory effects of salt on eNOS activity. The eNOS activity was unaffected in the presence of equal milliosmol of mannitol, which excludes an osmotic effect. Using an ex vivo aortic angiogenesis assay, we demonstrated that salt attenuated the nitric oxide (NO)-dependent proliferation of endothelial cells. By directly monitoring blood pressure changes in response to salt infusion, we found that in vivo infusion of salt induced an acute increase in blood pressure in a salt concentration-dependent manner. In conclusion, our findings demonstrated that eNOS is sensitive to changes in salt concentration. A 5-mmol/L rise in salt concentration, within the range observed in essential hypertension patients or in individuals with high salt intake, could significantly suppress eNOS activity. This salt-induced reduction in NO generation in endothelial cells may contribute to the development of hypertension.

Assessment of salt concentration in bread commonly consumed in the Eastern Mediterranean Region.

PubMed

Al Jawaldeh, Ayoub; Al-Khamaiseh, Manal

2018-04-05

Hypertension is the most important cardiovascular risk factor in the World Health Organization (WHO) Eastern Mediterranean Region. Excessive salt and sodium intake is directly related to hypertension, and its reduction is a priority of WHO. Bread is the leading staple food in the Region; therefore, reducing the amount of salt added to bread could be an effective measure for reducing salt intake. The study sought to determine the levels of sodium and salt in locally produced staple bread from 8 countries in the Region. Bread samples were collected randomly from bakeries located in the capital cities of the selected countries. The samples were analysed for sodium content using atomic absorption spectroscopy. The mean salt content of breads varied from 4.28 g/kg in Jordan to 12.41 g/kg in Tunisia. The mean salt and sodium content in bread for all countries was 7.63 (SD 3.12) and 3.0 (SD 1.23) g/kg, respectively. The contribution of bread to daily salt intake varied considerably between countries, ranging from 1.3 g (12.5%) in Jordan to 3.7 g (33.5%) in Tunisia. Interventions to reduce population salt intake should target reduction of salt in bread in all countries. The amount of salt added to bread should be standardized and relevant legislation developed to guide bakers. Setting an upper limit for salt content in flat bread (pita or Arabic bread) at 0.5% is strongly recommended. However, salt levels at ≤ 1% would be appropriate for other kind of breads. Copyright © World Health Organization (WHO) 2018. Some rights reserved. This work is available under the CC BY-NC-SA 3.0 IGO license (https://creativecommons.org/licenses/by-nc-sa/3.0/igo).

Executive Summary of the Cloud Impacts on DoD Operations and Systems - 1988 Workshop (CIDOS - 88)

DTIC Science & Technology

1988-01-01

over the Great Salt Lake Basin - an example of the complexity of satellite cloud detection. The image is photography #358 from the Large Format...over the Wasatch Range, east of the Great Salt Lake, and over the southern escarpment of the Uinta Mountains (lop right corner). The simple threshold

SUFFICIENT IODINE INTAKE IN SCHOOLCHILDREN FROM THE ZAGREB AREA: ASSESSMENT WITH DRIED BLOD SPOT THYROGLOBULIN AS A NEW FUNCTIONAL BIOMARKER FOR IODINE DEFICIENCY.

PubMed

Jukić, Tomislav; Zimmermann, Michael Bruce; Granić, Roko; Prpić, Marin; Krilić, Drazena; Juresa, Vesna; Katalenić, Marijan; Kusić, Zvonko

2015-12-01

Current methods for assessment of iodine intake in a population comprise measurements of urinary iodine concentration (UIC), thyroid volume by ultrasound (US-Tvol), and newborn TSH. Serum or dried blood spot thyroglobulin (DBS-Tg) is a new promising functional iodine status biomarker in children. In 1996, a new act on universal salt iodination was introduced in Croatia with 25 mg of potassium iodideper kg of salt. In 2002, Croatia finally reached iodine sufficiency. However, in 2009, median UIC in 101 schoolchildren from Zagreb, the capital of Croatia, was 288 µg/L, posing to be excessive. The aim of the study was to assess iodine intake in schoolchildren from the Zagreb area and to evaluate the value of DBS-Tg in schoolchildren as a new functional biomarker of iodine deficiency (and iodine excess). The study was part of a large international study in 6- to 12-year-old children supported by UNICEF, the Swiss Federal Institute of Technology (ETH Zurich) and the International Council for the Control of Iodine Deficiency Disorders (ICCIDD). According to international study results, the median cut-off Tg < 13 µg/L and/or < 3% Tg values > 40 µg/L indicate iodine sufficiency. The study included 159 schoolchildren (median age 9.1 ± 1.4 years) from Zagreb and a nearby small town of Jastrebarsko with measurements of UIC, US-Tvol, DBS-Tg, T4, TSH and iodine content in salt from households of schoolchildren (KI/kg of salt). Overall median UIC was 205 µg/L (range 1-505 µg/L). Thyroid volumes in schoolchildren measured by US were within the normal range according to reference values. Median DBS-Tg in schoolchildren was 12.1 µg/L with 3% of Tg values > 40 µg/L. High Tg values were in the UIC range < 50 µg/L and > 300 µg/L (U-shaped curve of Tg plotted against UIC). All children were euthyroid with geometric mean TSH 0.7 ± 0.3 mU/L and arithmetic mean T4 62 ± 12.5 nmol/L. The mean KI content per kg of salt was 24.9 ± 3.1 mg/kg (range 19-36 mg/kg). Study results indicated iodine sufficiency in schoolchildren from the Zagreb area. Thyroglobulin proved to be a sensitive indicator of both iodine deficiency and iodine excess in children. Iodine content in salt from households of schoolchildren was in good compliance with the Croatian act (20-30 mg KI/kg of salt).

Soil salinization in different natural zones of intermontane depressions in Tuva

NASA Astrophysics Data System (ADS)

Chernousenko, G. I.; Kurbatskaya, S. S.

2017-11-01

Soil salinization features in semidesert, dry steppe, and chernozemic steppe zones within intermontane depressions in the central part of the Tuva Republic are discussed. Chernozems, chestnut soils, and brown desert-steppe soils of these zones are usually nonsaline. However, salinization of these zonal soils is possible in the case of the presence of salt-bearing parent materials (usually, the derivatives of Devonian deposits). In different natural zones of the intermontane depressions, salt-affected soils are mainly allocated to endorheic lake basins, where they are formed in places of discharge of mineral groundwater, and to river valleys. The composition and content of salts in the natural waters are dictated by the local hydrogeological conditions. The total content of dissolved solids in lake water varies from 1 to 370 g/L; the water is usually of the sulfate-chloride or chloride-sulfate salinity type; in some cases, soda-sulfate water is present. Soil salinity around the lakes is usually of the chloride-sulfate-sodium type; gypsum is often present in the profiles. Chloride salinization rarely predominates in this part of Tuva, because chlorides are easily leached off from the mainly coarse-textured soils. In some cases, the predominance of magnesium over sodium is observed in the composition of dissolved salts, which may be indicative of the cryogenic transformation of soil salts. Soda-saline soils are present in all the considered natural zones on minor areas. It is hardly possible to make unambiguous statements about the dominance of the particular type of salinity in the given natural zones. Zonal salinity patterns are weakly expressed in salinization of hydromorphic soils. However, a tendency for more frequent occurrence of soda-saline soils in steppe landscapes and chloride-sulfate salinization (often, with participation of gypsum) in the dry steppe and semidesert landscapes is observed.

Pore Pressure and Field stress variation from Salt Water Injection; A case Study from Beaver Lodge Field in Williston Basin

NASA Astrophysics Data System (ADS)

Mohammed, R. A.; Khatibi, S.

2017-12-01

One of the major concerns in producing from oil and gas reservoirs in North American Basins is the disposal of high salinity salt water. It is a misconception that Hydro frack triggers Earthquakes, but due to the high salinity and density of water being pumped to the formation that has pore space of the rock already filled, which is not the case in Hydro-frack or Enhanced Oil Recovery in which fracturing fluid is pumped into empty pore space of rocks in depleted reservoirs. A review on the Bakken history showed that the concerns related to induce seismicity has increased over time due to variations in Pore pressure and In-situ stress that have shown steep changes in the region over the time. In this study, we focused on Pore pressure and field Stress variations in lower Cretaceous Inyan Kara and Mississippian Devonian Bakken, Inyan Kara is the major source for class-II salt-water disposal in the basin. Salt-water disposal is the major cause for induced seismicity. A full field study was done on Beaver Lodge Field, which has many salt-water disposal wells Adjacent to Oil and Gas Wells. We analyzed formation properties, stresses, pore-pressure, and fracture gradient profile in the field and. The constructed Mechanical Earth Model (MEM) revealed changes in pore pressure and stresses over time due to saltwater injection. Well drilled in the past were compared to recently drilled wells, which showed much stress variations. Safe mud weight Window of wells near proximity of injection wells was examined which showed many cases of wellbore instabilities. Results of this study will have tremendous impact in studying environmental issues and the future drilling and Fracking operations.

"Bath salts" intoxication: a new recreational drug that presents with a familiar toxidrome.

PubMed

Hall, Christine; Heyd, Christopher; Butler, Chris; Yarema, Mark

2014-03-01

It is important for emergency physicians to be aware of new psychoactive agents being used as recreational drugs. "Bath salts," which include 3,4-methylenedioxypyrovalerone (MDPV), mephedrone, and methylone, are the newest recreational stimulants to appear in Canada. There are currently more than 12 synthetic cathinones marketed as bath salts and used with increasing frequency recreationally. Although these drugs are now illegal in Canada, they are widely available online. We present a case report and discuss bath salts intoxication and its anticipated sympathomimetic toxidrome, treatment strategies, and toxicologic analysis, Treatment should not rely on laboratory confirmation. Since the laboratory identification of such drugs varies by institution and toxicologic assay, physicians should not misconstrue a negative toxicology screen as evidence of no exposure to synthetic cathinones. Illicit bath salts represent an increasing public health concern that involves risk to the user, prehospital personnel, and health care providers.

Simple and Sensitive Colorimetric Assay for Pb2+ Based on Glutathione Protected Ag Nanoparticles by Salt Amplification.

PubMed

Chen, Zhang; Li, Huidong; Chu, Lin; Liu, Chenbin; Luo, Shenglian

2015-02-01

A simple and sensitive colorimetric assay for Pb2+ detection has been reported using glutathione protected silver nanoparticles (AgNPs) by salt amplification. The naked AgNPs aggregate under the influence of salt. Glutathione (GSH) can bind to AgNPs via Ag-S bond, helping AgNPs to against salt-induced aggregation. However, GSH binding to AgNPs can be compromised by the interaction between Pb2+ and GSH. As a result, Pb2+-mediated aggregation of AgNPs under the influence of salt is reflected by the UV-Visible spectrum, and the qualitative and quantitative detection for Pb2+ is accomplished, with the detection range 0.5-4 µM and a detection limit of 0.5 µM. At the same time, Pb2+ in real water sample is detected. Furthermore, the high selectivity and low cost of the assay means it is promising for enviromental applications.

[Damage control resuscitation of severe multiple trauma in the pelvic fractures].

PubMed

Fu, Chang-guo

2015-05-01

To discuss the clinical effects of damage control resuscitation (DCR) in treating severe multiple trauma in the pelvic fractures. From March 2009 to September 2013, a restrospective analysis was conducted on the clinical data of 28 patients with multiple trauma in the pelvic fractures, including 19 males and 9 females, ranging in age from 21 to 51 years old with an average of 32.5 years old. According to Tile classification of pelvic fractures, 16 cases were type B and 12 cases were type C. Injury severity score (ISS) averaged 32.0±3.4. All cases were treated with damage contral orthopaedics and DCR strategy, namely that used immediately with small capacity of balanced salt solution on admission so as to maintain the blood pressure between 80 to 90 mmHg. At the same time, emergency phase I simple debridement plus external fixator or bundled with fixed pelvic was done, and the chest or abdomen combined injury was treated at first. And limbs fracture was temporary dealing with bone traction or plaster external fixation, etc. After bleeding was controlled by operation, fluid resuscitation was done as fast as possible and the plasma was transfused early according to the proportion of plasma and red cell suspension (2 U:1 U-3 U:2 U). Dosage of balanced salt solution and blood before remedy shock was recorded, and the removal of time of lactic acid and coagulation were observed. Five cases were died after 4 to 15 hours into hospital (3 cases died for severe trauma-hemorrhagic shock and 2 cases for acute respiratory distress syndrome). Twenty-three cases were remedy shock at 1.6 to 4.3 hours after injury with an average of 2.4 hours. Period I operation duration was (78.2±10.3) minutes. Dosage of balanced salt solution was (3,798±340) ml and red cell suspension was 14 to 18 U, fresh frozen plasma (FFP) was (1,267±58) ml (1U FFP=100 ml), blood platelet was 8 to 12 U for 9 patients. The removal time of lactic acid and PT-APTT was (11.4±2.1) hours and (4.3±0.8) hours. Measures were taken to correct electrolyte and acid-base imbalance was normal. The success rat of recovery was 82.2% (23/28). Damage control resuscitation (DCR) integrates the main links such as damage control operation and allowable low blood pressure (or limited liquid resuscitation) and hemostatic control resuscitation, was early effective treatment measures for the patients with severe multiple trauma in the pelvic fractures.

Stress corrosion evaluation of HP 9Ni-4Co-0.20C steel

NASA Technical Reports Server (NTRS)

Torres, Pablo D.

1993-01-01

A stress corrosion cracking (SCC) evaluation was undertaken on HP 9Ni-4Co-0.20C steel in support of the Advanced Solid Rocket Motor (ASRM) program. This alloy was tested in plate, bar, and ring forging forms. Several heat treating procedures yielded ultimate tensile strengths ranging from 1,407 to 1,489 MPa (204 to 216 ksi). The test environments were high humidity, alternate immersion in 3.5-percent NaCl, and 5-percent salt spray. Stress levels ranged from 25 to 90 percent of the yield strengths. The majority of the tests were conducted for 90 days. Even though the specimens rusted significantly in salt spray and alternate immersion, no failures occurred. Therefore, it can be concluded that this alloy, in the forms and at the strength levels tested, is highly resistant to SCC in salt and high humidity environments.

Measuring lanthanide concentrations in molten salt using laser-induced breakdown spectroscopy (LIBS).

PubMed

Weisberg, Arel; Lakis, Rollin E; Simpson, Michael F; Horowitz, Leo; Craparo, Joseph

2014-01-01

The versatility of laser-induced breakdown spectroscopy (LIBS) as an analytical method for high-temperature applications was demonstrated through measurement of the concentrations of the lanthanide elements europium (Eu) and praseodymium (Pr) in molten eutectic lithium chloride-potassium chloride (LiCl-KCl) salts at a temperature of 500 °C. Laser pulses (1064 nm, 7 ns, 120 mJ/pulse) were focused on the top surface of the molten salt samples in a laboratory furnace under an argon atmosphere, and the resulting LIBS signals were collected using a broadband Echelle-type spectrometer. Partial least squares (PLS) regression using leave-one-sample-out cross-validation was used to quantify the concentrations of Eu and Pr in the samples. The root mean square error of prediction (RMSEP) for Eu was 0.13% (absolute) over a concentration range of 0-3.01%, and for Pr was 0.13% (absolute) over a concentration range of 0-1.04%.

Thermal energy storage for power generation applications

NASA Astrophysics Data System (ADS)

Drost, M. K.; Antoniak, Zen I.; Brown, D. R.

1990-03-01

Studies strongly indicate that the United States will face widespread electrical power constraints in the 1990s. In many cases, the demand for increased power will occur during peak and intermediate demand periods. While natural gas is currently plentiful and economically attractive for meeting peak and intermediate loads, the development of a coal-fired peaking option would give utilities insurance against unexpected supply shortages or cost increases. This paper discusses a conceptual evaluation of using thermal energy storage (TES) to improve the economics of coal-fired peak and intermediate load power generation. The use of TES can substantially improve the economic attractiveness of meeting peak and intermediate loads with coal-fired power generation. In this case, conventional pulverized coal combustion equipment is continuously operated to heat molten nitrate salt, which is then stored. During peak demand periods, hot salt is withdrawn from storage and used to generate steam for a Rankine steam power cycle. This allows the coal-fired salt heater to be approximately one-third the size of a coal-fired boiler in a conventional cycling plant. The general impact is to decouple the generation of thermal energy from its conversion to electricity. The present study compares a conventional cycling pulverized coal-fired power plant to a pulverized coal-fired plant using nitrate salt TES. The study demonstrates that a coal-fired salt heater is technically feasible and should be less expensive than a similar coal-fired boiler. The results show the use of nitrate salt TES reduced the levelized cost of power by between 5 and 24 percent, depending on the operating schedule.

4D Imaging of Salt Precipitation during Evaporation from Saline Porous Media Influenced by the Particle Size Distribution

NASA Astrophysics Data System (ADS)

Norouzi Rad, M.; Shokri, N.

2014-12-01

Understanding the physics of water evaporation from saline porous media is important in many processes such as evaporation from porous media, vegetation, plant growth, biodiversity in soil, and durability of building materials. To investigate the effect of particle size distribution on the dynamics of salt precipitation in saline porous media during evaporation, we applied X-ray micro-tomography technique. Six samples of quartz sand with different grain size distributions were used in the present study enabling us to constrain the effects of particle and pore sizes on salt precipitation patterns and dynamics. The pore size distributions were computed using the pore-scale X-ray images. The packed beds were saturated with NaCl solution of 3 Molal and the X-ray imaging was continued for one day with temporal resolution of 30 min resulting in pore scale information about the evaporation and precipitation dynamics. Our results show more precipitation at the early stage of the evaporation in the case of sand with the larger particle size due to the presence of fewer evaporation sites at the surface. The presence of more preferential evaporation sites at the surface of finer sands significantly modified the patterns and thickness of the salt crust deposited on the surface such that a thinner salt crust was formed in the case of sand with smaller particle size covering larger area at the surface as opposed to the thicker patchy crusts in samples with larger particle sizes. Our results provide new insights regarding the physics of salt precipitation in porous media during evaporation.

Adsorption of poly(vinyl alcohol) from water to a hydrophobic surface: effects of molecular weight, degree of hydrolysis, salt, and temperature.

PubMed

Kozlov, Mikhail; McCarthy, Thomas J

2004-10-12

The adsorption of poly(vinyl alcohol) (PVOH) from aqueous solutions to a silicon-supported fluoroalkyl monolayer is described. Thickness, wettability, and roughness of adsorbed films are studied as a function of polymer molecular weight, degree of hydrolysis (from the precursor, poly(vinyl acetate)), polymer concentration, salt type and concentration, and temperature. The data suggest a two-stage process for adsorption of the polymer: physisorption due to a hydrophobic effect (decrease in interfacial free energy) and subsequent stabilization of the adsorbed layer due to crystallization of the polymer. Adsorption of lower-molecular-weight polymers results in thicker films than those prepared with a higher molecular weight; this is ascribed to better crystallization of more mobile short chains. Higher contents of unhydrolyzed acetate groups on the poly(vinyl alcohol) chain lead to thicker adsorbed films. Residual acetate groups partition to the outermost surface of the films and determine wettability. Salts, including sodium chloride and sodium sulfate, promote adsorption, which results in thicker films; at the same time, their presence over a wide concentration range leads to formation of rough coatings. Sodium thiocyanate has little effect on PVOH adsorption, only slightly reducing the thickness in a 2 M salt solution. Increased temperature promotes adsorption in the presence of salt, but has little effect on salt-free solutions. Evidently, higher temperatures favor adsorption but cause crystallization to be less thermodynamically favorable. These competing effects result in the smoothest coatings being formed in an intermediate temperature range. Copyright 2004 American Chemical Society

Ecological effects of climate change on salt marsh wildlife: a case study from a highly urbanized estuary

USGS Publications Warehouse

Thorne, Karen M.; Takekawa, John Y.; Elliott-Fisk, Deborah L.

2012-01-01

Coastal areas are high-risk zones subject to the impacts of global climate change, with significant increases in the frequencies of extreme weather and storm events, and sea-level rise forecast by 2100. These physical processes are expected to alter estuaries, resulting in loss of intertidal wetlands and their component wildlife species. In particular, impacts to salt marshes and their wildlife will vary both temporally and spatially and may be irreversible and severe. Synergistic effects caused by combining stressors with anthropogenic land-use patterns could create areas of significant biodiversity loss and extinction, especially in urbanized estuaries that are already heavily degraded. In this paper, we discuss current ideas, challenges, and concerns regarding the maintenance of salt marshes and their resident wildlife in light of future climate conditions. We suggest that many salt marsh habitats are already impaired and are located where upslope transgression is restricted, resulting in reduction and loss of these habitats in the future. In addition, we conclude that increased inundation frequency and water depth will have negative impacts on the demography of small or isolated wildlife meta-populations as well as their community interactions. We illustrate our points with a case study on the Pacific Coast of North America at San Pablo Bay National Wildlife Refuge in California, an area that supports endangered wildlife species reliant on salt marshes for all aspects of their life histories.

Geomechanical analysis to predict the oil leak at the wellbores in Big Hill Strategic Petroleum Reserve

DOE Office of Scientific and Technical Information (OSTI.GOV)

Park, Byoung Yoon

2014-02-01

Oil leaks were found in wellbores of Caverns 105 and 109 at the Big Hill Strategic Petroleum Reserve site. According to the field observations, two instances of casing damage occurred at the depth of the interbed between the caprock bottom and salt top. A three dimensional finite element model, which contains wellbore element blocks and allows each cavern to be configured individually, is constructed to investigate the wellbore damage mechanism. The model also contains element blocks to represent interface between each lithology and a shear zone to examine the interbed behavior in a realistic manner. The causes of the damagedmore » casing segments are a result of vertical and horizontal movements of the interbed between the caprock and salt dome. The salt top subsides because the volume of caverns below the salt top decrease with time due to salt creep closure, while the caprock subsides at a slower rate because the caprock is thick and stiffer. This discrepancy yields a deformation of the well. The deformed wellbore may fail at some time. An oil leak occurs when the wellbore fails. A possible oil leak date of each well is determined using the equivalent plastic strain failure criterion. A well grading system for a remediation plan is developed based on the predicted leak dates of each wellbore.« less

Geomechanical Simulation to Predict the Oil Leak at the Wellbores in Big Hill Strategic Petroleum Reserve.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Park, Byoung; Herrick, Courtney G.

2015-02-01

Oil leaks were found in wellbores of Caverns 105 and 109 at the Big Hill Strategic Petroleum Reserve site. According to the field observations, two instances of casing damage occurred at the depth of the interbed between the caprock bottom and salt top. A three dimensional finite element model, which contains wellbore element blocks and allows each cavern to be configured individually, is constructed to investigate the wellbore damage mechanism. The model also contains element blocks to represent interface between each lithology and a shear zone to examine the interbed behavior in a realistic manner. The causes of the damagedmore » casing segments are a result of vertical and horizontal movements of the interbed between the caprock and salt dome. The salt top subsides because the volume of caverns below the salt top decrease with time due to salt creep closure, while the caprock subsides at a slower rate because the caprock is thick and stiffer. This discrepancy produces a deformation of the well. The deformed wellbore may fail at some time. An oil leak occurs when the wellbore fails. A possible oil leak date of each well is determined using an equivalent plastic strain failure criterion. A well grading system for a remediation plan is developed based on the predicted leak dates of each wellbore.« less

Changes in salt-marsh carabid assemblages after an invasion by the native grass Elymus athericus (Link) Kerguélen

PubMed Central

Georges, Anita; Fouillet, Philippe; Pétillon, Julien

2011-01-01

Abstract As a result of an invasion by the native grass Elymus athericus (Link) Kerguélen (Poaceae) in the last 10 years, a major change in vegetation cover has occurred in salt marshes of the Mont Saint-Michel bay, Western France. The impact of such an invasion on carabid assemblages, a dominant group of terrestrial arthropods in these habitats and containing several stenotopic species, is investigated here. In our study site, carabid data are available from 1983 and 1984, allowing a comparison of species distribution ranges in salt marshes before (1983–1984) and after (2002) the Elymus athericus invasion. A total of 16,867 adults belonging to 40 species were caught. By considering the presence-absence of species shared between studies, we show that the invasion by Elymus athericus promoted the progression of non-coastal species (mainly Pterostichus s.l. spp.). This did however not interfere with resident species distributions, finally resulting in higher carabid species richness in the entire area. The species composition and abundances of carabid assemblages were also compared between natural and invaded stations in 2002. The main result is that abundances of some halophilic species decreased in one invaded plot (in case of Pogonus chalceus (Marsham 1802)) whereas the opposite pattern was observed for other species (e.g., Bembidion minimum (Fabricius 1792)). Invaded habitats were characterized by lower percentages of halophilic species and higher total species richness. PMID:21738424

Recent results on aqueous electrolyte cells

NASA Astrophysics Data System (ADS)

Wessells, Colin; Huggins, Robert A.; Cui, Yi

2011-03-01

The improved safety of aqueous electrolytes makes aqueous lithium-ion batteries an attractive alternative to commercial cells utilizing flammable and expensive organic electrolytes. Two important issues relating to their use have been addressed in this work. One is the extension of the usable voltage range by the incorporation of lithium salts, and the other is the investigation of a useful negative electrode reactant, LiTi2(PO4)3. The electrochemical stability of aqueous lithium salt solutions containing two lithium salts, LiNO3 and Li2SO4, has been characterized using a constant current technique. In both cases, concentrated solutions had effective electrolyte stability windows substantially greater than that of pure water under standard conditions. At an electrolyte leakage current of 10 μA cm-2 between two platinum electrodes in 5 M LiNO3 the cell voltage can reach 2.0 V, whereas with a leakage current of 50 μA cm-2 it can reach 2.3 V. LiTi2(PO4)3 was synthesized using a Pechini method and cycled in pH-neutral Li2SO4. At a reaction potential near the lower limit of electrolyte stability, an initial discharge capacity of 118 mAh g-1 was measured at a C/5 rate, while about 90% of this discharge capacity was retained after 100 cycles. This work demonstrates that it is possible to have useful aqueous electrolyte lithium-ion batteries using the LiTi2(PO4)3 anode with cell voltages of 2 V and above.

The variability of reported salt levels in fast foods across six countries: opportunities for salt reduction.

PubMed

Dunford, Elizabeth; Webster, Jacqueline; Woodward, Mark; Czernichow, Sebastien; Yuan, Wen Lun; Jenner, Katharine; Ni Mhurchu, Cliona; Jacobson, Michael; Campbell, Norm; Neal, Bruce

2012-06-12

Several fast food companies have made commitments to reduce the levels of salt in the foods they serve, but technical issues are often cited as a barrier to achieving substantial reductions. Our objective was to examine the reported salt levels for products offered by leading multinational fast food chains. Data on salt content for products served by six fast food chains operating in Australia, Canada, France, New Zealand, the United Kingdom and the United States were collected by survey in April 2010. Mean salt contents (and their ranges) were calculated and compared within and between countries and companies. We saw substantial variation in the mean salt content for different categories of products. For example, the salads we included in our survey contained 0.5 g of salt per 100 g, whereas the chicken products we included contained 1.6 g. We also saw variability between countries: chicken products from the UK contained 1.1 g of salt per 100 g, whereas chicken products from the US contained 1.8 g. Furthermore, the mean salt content of food categories varied between companies and between the same products in different countries (e.g., McDonald's Chicken McNuggets contain 0.6 g of salt per 100 g in the UK, but 1.6 g of salt per 100 g in the US). The salt content of fast foods varies substantially, not only by type of food, but by company and country in which the food is produced. Although the reasons for this variation are not clear, the marked differences in salt content of very similar products suggest that technical reasons are not a primary explanation. In the right regulatory environment, it is likely that fast food companies could substantially reduce the salt in their products, translating to large gains for population health.

The variability of reported salt levels in fast foods across six countries: opportunities for salt reduction

PubMed Central

Dunford, Elizabeth; Webster, Jacqueline; Woodward, Mark; Czernichow, Sebastien; Yuan, Wen Lun; Jenner, Katharine; Mhurchu, Cliona Ni; Jacobson, Michael; Campbell, Norm; Neal, Bruce

2012-01-01

Background: Several fast food companies have made commitments to reduce the levels of salt in the foods they serve, but technical issues are often cited as a barrier to achieving substantial reductions. Our objective was to examine the reported salt levels for products offered by leading multinational fast food chains. Methods: Data on salt content for products served by six fast food chains operating in Australia, Canada, France, New Zealand, the United Kingdom and the United States were collected by survey in April 2010. Mean salt contents (and their ranges) were calculated and compared within and between countries and companies. Results: We saw substantial variation in the mean salt content for different categories of products. For example, the salads we included in our survey contained 0.5 g of salt per 100 g, whereas the chicken products we included contained 1.6 g. We also saw variability between countries: chicken products from the UK contained 1.1 g of salt per 100 g, whereas chicken products from the US contained 1.8 g. Furthermore, the mean salt content of food categories varied between companies and between the same products in different countries (e.g., McDonald’s Chicken McNuggets contain 0.6 g of salt per 100 g in the UK, but 1.6 g of salt per 100 g in the US). Interpretation: The salt content of fast foods varies substantially, not only by type of food, but by company and country in which the food is produced. Although the reasons for this variation are not clear, the marked differences in salt content of very similar products suggest that technical reasons are not a primary explanation. In the right regulatory environment, it is likely that fast food companies could substantially reduce the salt in their products, translating to large gains for population health. PMID:22508978

Performance evaluation of two protective treatments on salt-laden limestones and marble after natural and artificial weathering.

PubMed

Salvadori, Barbara; Pinna, Daniela; Porcinai, Simone

2014-02-01

Salt crystallization is a major damage factor in stone weathering, and the application of inappropriate protective products may amplify its effects. This research focuses on the evaluation of two protective products' performance (organic polydimethylsiloxane and inorganic ammonium oxalate (NH4)2(COO)2·H2O) in the case of a salt load from behind. Experimental laboratory simulations based on salt crystallization cycles and natural weathering in an urban area were carried out. The effects were monitored over time, applying different methods: weight loss evaluation, colorimetric and water absorption by capillarity measurements, stereomicroscope observations, FTIR and SEM-EDS analyses. The results showed minor impact exerted on the short term on stones, particularly those treated with the water repellent, by atmospheric agents compared to salt crystallization. Lithotypes with low salt load (Gioia marble) underwent minor changes than the heavily salt-laden limestones (Lecce and Ançã stones), which were dramatically damaged when treated with polysiloxane. The results suggest that the ammonium oxalate treatment should be preferred to polysiloxane in the presence of soluble salts, even after desalination procedures which might not completely remove them. In addition, the neo-formed calcium oxalate seemed to effectively protect the stone, improving its resistance against salt crystallization without occluding the pores and limiting the superficial erosion caused by atmospheric agents.

Secondary Aluminum Processing Waste: Salt Cake ...

EPA Pesticide Factsheets

Thirty-nine salt cake samples were collected from 10 SAP facilities across the U.S. The facilities were identified by the Aluminum Association to cover a wide range of processes. Results suggest that while the percent metal leached from the salt cake was relatively low, the leachable metal content may still pose a contamination concern and potential human and ecological exposure if uncontrollably released to the environment. As a result, salt cake should always be managed at facilities that utilize synthetic liner systems with leachate collection (the salt content of the leachate will increase the hydraulic conductivity of clay liners within a few years of installation). The mineral phase analysis showed that various species of aluminum are present in the salt cake samples with a large degree of variability. The relative abundance of various aluminum species was evaluated but it is noted that the method used is a semi-quantitative method and as a result there is a limitation for the data use. The analysis only showed a few aluminum species present in salt cake which does not exclude the presence of other crystalline species especially in light of the variability observed in the samples. Results presented in this document are of particular importance when trying to understand concerns associated with the disposal of salt cake in MSW landfills. From the end-of-life management perspective, data presented here suggest that salt cake should not be size reduce

Properties of a Purified Halophilic Malic Dehydrogenase

PubMed Central

Holmes, P. K.; Halvorson, H. Orin

1965-01-01

Holmes, P. K. (University of Illinois, Urbana), and H. Orin Halvorson. Properties of a purified halophilic malic dehydrogenase. J. Bacteriol. 90:316–326. 1965.—The malic dehydrogenase (MDH) from Halobacterium salinarium required high concentrations of monovalent ions for stability and activity. Studies of inactivation rates at different salt concentrations suggested that approximately 25% NaCl (w/v) is required to stabilize MDH. From 50 to 100% reactivation, depending on the salt concentration present during inactivation, could occur in 2.5 to 5 m NaCl or KCl. The optimal salt concentration for activity of MDH was a function of the pH, and ranged from 1 to 3 m NaCl or KCl. The effect of salt concentration on the pH-activity curves occurred chiefly below pH 7.0. Inactivation of MDH with heat or thiol reagents showed that the enzyme was more labile in the state induced by absence of salt. The activation of MDH by salts was attributed to a decreased rate of dissociation of MDH and reduced nicotinamide adenine dinucleotide (NADH2). The inactivation of the enzyme in the absence of salt could be largely prevented by the presence of NADH2. The S20.w of MDH decreased threefold at low salt concentrations. The enzyme was assumed to be in its native compact configuration only in the presence of a high concentration of salt. PMID:14329442

Nutritional modelling: distributions of salt intake from processed foods in New Zealand.

PubMed

Thomson, Barbara M

2009-09-01

The salt content of processed foods is important because of the high intake of Na by most New Zealanders. A database of Na concentrations in fifty-eight processed foods was compiled from existing and new data and combined with 24 h diet recall data from two national nutrition surveys (5771 respondents) to derive salt intakes for seven population groups. Mean salt intakes from processed foods ranged from 6.9 g/d for young males aged 19-24 years to 3.5 g/d for children aged 5-6 years. A total of > or = 50 % of children aged 5-6 years, boys aged 11-14 years and young males aged 19-24 years had salt intakes that exceeded the upper limit for Na, calculated as salt (3.2-5.3 g/d), from processed foods only. Bread accounted for the greatest contribution to salt intake for each population group (35-43 % of total salt intake). Other foods that contributed 2 % or more and common across most age groups were sausage, meat pies, pizza, instant noodles and cheese. The Na concentrations of key foods have changed little over the 16-year period from 1987 to 2003 except for corned beef and whole milk that have decreased by 34 and 50 % respectively. Bread is an obvious target for salt reduction but the implication on iodine intake needs consideration as salt is used as a vehicle for iodine fortification of bread.

Stabilization of molten salt materials using metal chlorides for solar thermal storage.

PubMed

Dunlop, T O; Jarvis, D J; Voice, W E; Sullivan, J H

2018-05-29

The effect of a variety of metal-chlorides additions on the melting behavior and thermal stability of commercially available salts was investigated. Ternary salts comprised of KNO 3, NaNO 2, and NaNO 3 were produced with additions of a variety of chlorides (KCl, LiCl, CaCl 2 , ZnCl 2 , NaCl and MgCl 2 ). Thermogravimetric analysis and weight loss experiments showed that the quaternary salt containing a 5 wt% addition of LiCl and KCl led to an increase in short term thermal stability compared to the ternary control salts. These additions allowed the salts to remain stable up to a temperature of 630 °C. Long term weight loss experiments showed an upper stability increase of 50 °C. A 5 wt% LiCl addition resulted in a weight loss of only 25% after 30 hours in comparison to a 61% loss for control ternary salts. Calorimetry showed that LiCl additions allow partial melting at 80 °C, in comparison to the 142 °C of ternary salts. This drop in melting point, combined with increased stability, provided a molten working range increase of almost 100 °C in total, in comparison to the control ternary salts. XRD analysis showed the oxidation effect of decomposing salts and the additional phase created with LiCl additions to allow melting point changes to occur.

An application of LOTEM around salt dome near Houston, Texas

NASA Astrophysics Data System (ADS)

Paembonan, Andri Yadi; Arjwech, Rungroj; Davydycheva, Sofia; Smirnov, Maxim; Strack, Kurt M.

2017-07-01

A salt dome is an important large geologic structure for hydrocarbon exploration. It may seal a porous reservoir of rocks that form petroleum reservoirs. Several techniques such as seismic, gravity, and electromagnetic including magnetotelluric have successfully yielded salt dome interpretation. Seismic has difficulties seeing through the salt because the seismic energy gets trapped by the salt due to its high velocity. Gravity and electromagnetics are more ideal methods. Long Offset Transient Electromagnetic (LOTEM) and Focused Source Electromagnetic (FSEM) were tested over a salt dome near Houston, Texas. LOTEM data were recorded at several stations with varying offset, and the FSEM tests were also made at some receiver locations near a suspected salt overhang. The data were processed using KMS's processing software: First, for assurance, including calibration and header checking; then transmitter and receiver data are merged and microseismic data is separated; Finally, data analysis and processing follows. LOTEM processing leads to inversion or in the FSEM case 3D modeling. Various 3D models verify the sensitivity under the salt dome. In addition, the processing was conducted pre-stack, stack, and post-stack. After pre-stacking, the noise was reduced, but showed the ringing effect due to a low-pass filter. Stacking and post-stacking with applying recursive average could reduce the Gibbs effect and produce smooth data.

Environmental impact on construction limestone at humid regions with an emphasis on salt weathering, Al-hambra islamic archaeological site, Granada City, Spain: case study

NASA Astrophysics Data System (ADS)

Kamh, G. M. E.

2007-08-01

Al-hambra is an immense and valuable archaeological site in Spain built on Sabika hill with red brick and natural sandy limestone. It exhibits weathering features indicating salt weathering process. The main aim of this study is to examine weathering processes and intensity acting on Al-hambra. Rock petrography and mineralogical composition have been examined using thin sections, scanning electron microscope, X-ray diffraction and X-ray fluorescence; limits of rock’s physical parameters using ultrasonic waves and mercury porosimeter; rock salt content through hydrochemical analysis. Salts attacking this structure are mainly from wet deposition of air pollutants on the long term chemical alteration of rock’s carbonate content to its equivalent salts. The salts’ concentration limit within the examined rock samples is considerably low but it is effective on the long run through hydration of sulphate salts and/or crystallization of chloride salts. Rock texture type and its silica as well as clay content reduces its resistance to internal stresses by salts as well as wetting and drying cycles at such humid area. The recession in limits of physical parameters examined for deep seated and weathered limestone samples quantitatively reflects weathering intensity on Al-hambra.

Geologic appraisal of Paradox basin salt deposits for water emplacement

USGS Publications Warehouse

Hite, Robert J.; Lohman, Stanley William

1973-01-01

Thick salt deposits of Middle Pennsylvanian age are present in an area of 12,000 square miles in the Paradox basin of southeast Utah and southwest Colorado. The deposits are in the Paradox Member of the Hermosa Formation. The greatest thickness of this evaporite sequence is in a troughlike depression adjacent to the Uncompahgre uplift on the northeast side of the basin.The salt deposits consist of a cyclical sequence of thick halite units separated by thin units of black shale, dolomite, and anhydrite. Many halite units are several hundred feet thick and locally contain economically valuable potash deposits.Over much of the Paradox basin the salt deposits occur at depths of more than 5,000 feet. Only in a series of salt anticlines located along the northeastern side of the basin do the salt deposits rise to relatively shallow depths. The salt anticlines can be divided geographically and structurally into five major systems. Each system consists of a long undulating welt of thickened salt over which younger rocks are arched in anticlinal form. Locally there are areas along the axes of the anticlines where the Paradox Member was never covered by younger sediments. This allowed large-scale migration of Paradox strata toward and up through these holes in the sediment cover forming diapiric anticlines.The central or salt-bearing cores of the anticlines range in thickness from about 2,500 to 14,000 feet. Structure in the central core of the salt anticlines is the result of both regional-compression and flowage of the Paradox Member into the anticlines from adjacent synclines. Structure in the central cores of the salt anticlines ranges from relatively undeformed beds to complexly folded and faulted masses, in which stratigraphic continuity is undemonstrable.The presence of thick cap rock .over many of the salt anticlines is evidence of removal of large volumes of halite by groundwater. Available geologic and hydrologic information suggests that this is a relatively slow process and that any waste-storage or disposal sites in these structures should remain dry for hundreds of thousands of years.Trace to commercial quantities of oil and gas are found in all of the black shale-dolomite-anhydrite interbeds of the Paradox Member. These hydrocarbons constitute a definite hazard in the construction and operation of underground waste-storage or disposal facilities. However, many individual halite beds are of. sufficient thickness that a protective seal of halite can be left between the openings and the gassy beds.A total of 12 different localities were considered to be potential waste-storage or disposal sites in the Paradox basin. Two Sharer dome and Salt Valley anticline, were considered to have the most favorable characteristics.

Genomic, transcriptomic, and proteomic approaches towards understanding the molecular mechanisms of salt tolerance in Frankia strains isolated from Casuarina trees.

PubMed

Oshone, Rediet; Ngom, Mariama; Chu, Feixia; Mansour, Samira; Sy, Mame Ourèye; Champion, Antony; Tisa, Louis S

2017-08-18

Soil salinization is a worldwide problem that is intensifying because of the effects of climate change. An effective method for the reclamation of salt-affected soils involves initiating plant succession using fast growing, nitrogen fixing actinorhizal trees such as the Casuarina. The salt tolerance of Casuarina is enhanced by the nitrogen-fixing symbiosis that they form with the actinobacterium Frankia. Identification and molecular characterization of salt-tolerant Casuarina species and associated Frankia is imperative for the successful utilization of Casuarina trees in saline soil reclamation efforts. In this study, salt-tolerant and salt-sensitive Casuarina associated Frankia strains were identified and comparative genomics, transcriptome profiling, and proteomics were employed to elucidate the molecular mechanisms of salt and osmotic stress tolerance. Salt-tolerant Frankia strains (CcI6 and Allo2) that could withstand up to 1000 mM NaCl and a salt-sensitive Frankia strain (CcI3) which could withstand only up to 475 mM NaCl were identified. The remaining isolates had intermediate levels of salt tolerance with MIC values ranging from 650 mM to 750 mM. Comparative genomic analysis showed that all of the Frankia isolates from Casuarina belonged to the same species (Frankia casuarinae). Pangenome analysis revealed a high abundance of singletons among all Casuarina isolates. The two salt-tolerant strains contained 153 shared single copy genes (most of which code for hypothetical proteins) that were not found in the salt-sensitive(CcI3) and moderately salt-tolerant (CeD) strains. RNA-seq analysis of one of the two salt-tolerant strains (Frankia sp. strain CcI6) revealed hundreds of genes differentially expressed under salt and/or osmotic stress. Among the 153 genes, 7 and 7 were responsive to salt and osmotic stress, respectively. Proteomic profiling confirmed the transcriptome results and identified 19 and 8 salt and/or osmotic stress-responsive proteins in the salt-tolerant (CcI6) and the salt-sensitive (CcI3) strains, respectively. Genetic differences between salt-tolerant and salt-sensitive Frankia strains isolated from Casuarina were identified. Transcriptome and proteome profiling of a salt-tolerant strain was used to determine molecular differences correlated with differential salt-tolerance and several candidate genes were identified. Mechanisms involving transcriptional and translational regulation, cell envelop remodeling, and previously uncharacterized proteins appear to be important for salt tolerance. Physiological and mutational analyses will further shed light on the molecular mechanism of salt tolerance in Casuarina associated Frankia isolates.

Hydrogen-bond symmetrization in methane and hydrogen hydrates in the Mbar range

NASA Astrophysics Data System (ADS)

Bove, L. E.; Ranieri, U.; Gaal, R.; Finocchi, F.; Kuhs, W. F.; Falenty, A.; Klotz, S.; Gillet, P.

2016-12-01

Ice-VII and ice-X phases are the most stable forms of ice at high temperature and extreme pressures, typical of the interiors of satellites and planets. The phase transition between them is a prototypical case of quantum-driven phenomenon, as it can be described as a quantum delocalization of protons in the middle of O-O distances. Recent studies on LiCl- and NaCl-doped ice 1-3 have shown that the presence of salt inclusions in the ice lattice suppresses the quantum behavior of protons, hindering the appearance of the symmetric phase, and possibly suppressing the predicted high temperature superionic phase. This finding stimulated the investigation of similar effects in other water-based compounds, which are thought to be present in icy bodies, namely hydrogen and methane high pressure hydrates. Few experiments have been performed in the past to identify signatures of the hydrogen-bond symmetrization in methane and hydrogen hydrates without reaching conclusive results4,5. Here we present new results on the hydrogen-bond symmetrization of methane and hydrogen hydrates using Raman scattering in the Mbar range and semiclassical simulations including nuclear quantum effects. 1 Bove L. E. et al., E_ect of salt on the H-bond symmetrization in ice, Proc. Natl. Acad. Sci. USA 112, 8216, 2015 ; 2. Bronstein Y. et al., Quantum versus classical protons in pure and salty ice under pressure, Phys. Rev. B 93, 024104, 2016. 3. Klotz S. et al., Ice VII from aqueous salt solutions: From a glass to a crystal with broken H-bonds, Nature Sci. Rep. , in press. 4. Tanaka T. et al., Phase changes of _lled ice Ih methane hydrate under low temperature and high pressure, J. Chem. Phys. 139, 104701, 2013 5. Hirai H. et al., Structural changes of _lled ice Ic hydrogen hydrate under low temperatures and high pressures from 5 to 50 GPa, J. Chem. Phys. 137, 074505, 2012

Hydrogen production under salt stress conditions by a freshwater Rhodopseudomonas palustris strain.

PubMed

Adessi, Alessandra; Concato, Margherita; Sanchini, Andrea; Rossi, Federico; De Philippis, Roberto

2016-03-01

Hydrogen represents a possible alternative energy carrier to face the growing request for energy and the shortage of fossil fuels. Photofermentation for the production of H2 constitutes a promising way for integrating the production of energy with waste treatments. Many wastes are characterized by high salinity, and polluted seawater can as well be considered as a substrate. Moreover, the application of seawater for bacterial culturing is considered cost-effective. The aims of this study were to assess the capability of the metabolically versatile freshwater Rhodopseudomonas palustris 42OL of producing hydrogen on salt-containing substrates and to investigate its salt stress response strategy, never described before. R. palustris 42OL was able to produce hydrogen in media containing up to 3 % added salt concentration and to grow in media containing up to 4.5 % salinity without the addition of exogenous osmoprotectants. While the hydrogen production performances in absence of sea salts were higher than in their presence, there was no significant difference in performances between 1 and 2 % of added sea salts. Nitrogenase expression levels indicated that the enzyme was not directly inhibited during salt stress, but a regulation of its expression may have occurred in response to salt concentration increase. During cell growth and hydrogen production in the presence of salts, trehalose was accumulated as a compatible solute; it protected the enzymatic functionality against salt stress, thus allowing hydrogen production. The possibility of producing hydrogen on salt-containing substrates widens the range of wastes that can be efficiently used in production processes.

Projected Impact of Salt Restriction on Prevention of Cardiovascular Disease in China: A Modeling Study

PubMed Central

Liu, Jing; Coxson, Pamela G.; Penko, Joanne; Goldman, Lee; Bibbins-Domingo, Kirsten; Zhao, Dong

2016-01-01

Objectives To estimate the effects of achieving China’s national goals for dietary salt (NaCl) reduction or implementing culturally-tailored dietary salt restriction strategies on cardiovascular disease (CVD) prevention. Methods The CVD Policy Model was used to project blood pressure lowering and subsequent downstream prevented CVD that could be achieved by population-wide salt restriction in China. Outcomes were annual CVD events prevented, relative reductions in rates of CVD incidence and mortality, quality-adjusted life-years (QALYs) gained, and CVD treatment costs saved. Results Reducing mean dietary salt intake to 9.0 g/day gradually over 10 years could prevent approximately 197 000 incident annual CVD events [95% uncertainty interval (UI): 173 000–219 000], reduce annual CVD mortality by approximately 2.5% (2.2–2.8%), gain 303 000 annual QALYs (278 000–329 000), and save approximately 1.4 billion international dollars (Int$) in annual CVD costs (Int$; 1.2–1.6 billion). Reducing mean salt intake to 6.0 g/day could approximately double these benefits. Implementing cooking salt-restriction spoons could prevent 183 000 fewer incident CVD cases (153 000–215 000) and avoid Int$1.4 billion in CVD treatment costs annually (1.2–1.7 billion). Implementing a cooking salt substitute strategy could lead to approximately three times the health benefits of the salt-restriction spoon program. More than three-quarters of benefits from any dietary salt reduction strategy would be realized in hypertensive adults. Conclusion China could derive substantial health gains from implementation of population-wide dietary salt reduction policies. Most health benefits from any dietary salt reduction program would be realized in adults with hypertension. PMID:26840409

Determination of salt content in hot takeaway meals in the United Kingdom.

PubMed

Jaworowska, Agnieszka; Blackham, Toni; Stevenson, Leonard; Davies, Ian G

2012-10-01

High sodium intake is associated with negative health outcomes, including an independent correlation with high blood pressure which increases the risk of cardiovascular disease. A high proportion of sodium intake in the UK is from processed and out of the home food; this includes takeaway food which is increasing in popularity. The aim of the present study was to evaluate salt levels in popular hot takeaway meals. A total of 411 samples of 23 different types of takeaway meals were analysed. Obtained results show the salt content in these kinds of foods is alarmingly high. Comparing medians (interquartile range) for different meal categories, Pizzas contained the highest salt content per portion (9.45 g (6.97-12.83)), followed by Chinese meals (8.07 g (5.47-10.99 g)), Kebabs (6.21 g (4.01-8.35)) and Indian meals (4.73 g (3.61-6.10)). In addition, significant differences in the salt content between meals within the same category were reported. To enable the consumer to meet the UK's target salt intake, a significant reduction in the salt content of hot takeaway meals should be considered. Copyright © 2012 Elsevier Ltd. All rights reserved.

Vacuum distillation of a mixture of LiCl-KCl eutectic salts and RE oxidative precipitates and a dechlorination and oxidation of RE oxychlorides.

PubMed

Eun, Hee Chul; Yang, Hee Chul; Cho, Yung Zun; Lee, Han Soo; Kim, In Tae

2008-12-30

In this study, a vacuum distillation of a mixture of LiCl-KCl eutectic salt and rare-earth oxidative precipitates was performed to separate a pure LiCl-KCl eutectic salt from the mixture. Also, a dechlorination and oxidation of the rare-earth oxychlorides was carried out to stabilize a final waste form. The mixture was distilled under a range of 710-759.5Torr of a reduced pressure at a fixed heating rate of 4 degrees C/min and the LiCl-KCl eutectic salt was completely separated from the mixture. The required time for the salt distillation and the starting temperature for the salt vaporization were lowered with a reduction in the pressure. Dechlorination and oxidation of the rare-earth oxychlorides was completed at a temperature below 1300 degrees C and this was dependent on the partial pressure of O2. The rare-earth oxychlorides (NdOCl/PrOCl) were transformed to oxides (Nd2O3/PrO2) during the dechlorination and oxidation process. These results will be utilized to design a concept for a process for recycling the waste salt from an electrorefining process.

Thermophysical properties of low cost lithium nitrate salts produced in northern Chile for thermal energy storage

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fernández, Ángel G.; Gomez-Vidal, Judith C.

In recent years, lithium containing salts have been studied for thermal energy storage (TES) applications because of their excellent thermophysical properties. In solar power plants, lithium is seen as a way to improve the properties of state-of-the art molten salts used today. Lithium nitrate is a good candidate for sensible heat storage, because of its ability to increase the salt mixture's working temperature range. In the present research, thermophysical properties characterization of lithium nitrate containing salts, produced in Chile, have been carried out. Corrosion evaluations at 390° and 565 °C for 1000 h were performed for low chromium steel T22more » and stainless steels (AISI 430 and AISI 316), respectively. Chemical composition of the salts including identification of corrosion products and impurities was determined and an estimation of the Chilean production costs is reported. The study shows a loss of thermal properties after the corrosion tests. The heat capacity was reduced, possibly caused by the formation of oxides at high temperatures. As a result, the partial thermal decomposition of the salt was probably produced by the incorporation of corrosion products from the steel.« less

Thermophysical properties of low cost lithium nitrate salts produced in northern Chile for thermal energy storage

DOE PAGES

Fernández, Ángel G.; Gomez-Vidal, Judith C.

2016-09-01

In recent years, lithium containing salts have been studied for thermal energy storage (TES) applications because of their excellent thermophysical properties. In solar power plants, lithium is seen as a way to improve the properties of state-of-the art molten salts used today. Lithium nitrate is a good candidate for sensible heat storage, because of its ability to increase the salt mixture's working temperature range. In the present research, thermophysical properties characterization of lithium nitrate containing salts, produced in Chile, have been carried out. Corrosion evaluations at 390° and 565 °C for 1000 h were performed for low chromium steel T22more » and stainless steels (AISI 430 and AISI 316), respectively. Chemical composition of the salts including identification of corrosion products and impurities was determined and an estimation of the Chilean production costs is reported. The study shows a loss of thermal properties after the corrosion tests. The heat capacity was reduced, possibly caused by the formation of oxides at high temperatures. As a result, the partial thermal decomposition of the salt was probably produced by the incorporation of corrosion products from the steel.« less

Conversion of alkali metal sulfate to the carbonate

DOEpatents

Sheth, Atul C.

1982-01-01

A process for converting potassium sulfate to potassium carbonate in which a mixture of potassium sulfate and calcium oxide are reacted at a temperature in the range of between about 700.degree. C. and about 800.degree. C. with a gaseous mixture having a minor amount of hydrogen and/or carbon monoxide in a diluent with the calcium oxide being present in an amount not greater than about 20 percent by weight of the potassium sulfate to produce an aqueous mixture of potassium sulfide, potassium bisulfide, potassium hydroxide and calcium sulfide and a gaseous mixture of steam and hydrogen sulfide. The potassium and calcium salts are quenched to produce an aqueous slurry of soluble potassium salts and insoluble calcium salts and a gaseous mixture of steam and hydrogen sulfide. The insoluble calcium salts are then separated from the aqueous solution of soluble potassium salts. The calcium salts are dried to produce calcium sulfide, calcium bisulfide and steam, and then, the calcium sulfide and calcium bisulfide are converted to the oxide and recycled. The soluble potassium salts are carbonated to produce potassium carbonate which is concentrated and the precipitated crystals separated. The sulfur-containing compounds are further treated.

Loss of CaMKI function disrupts salt aversive learning in C. elegans.

PubMed

Lim, Jana P; Fehlauer, Holger; Das, Alakananda; Saro, Gabriella; Glauser, Dominique A; Brunet, Anne; Goodman, Miriam B

2018-06-06

The ability to adapt behavior to environmental fluctuations is critical for survival of organisms ranging from invertebrates to mammals. Caenorhabditis elegans can learn to avoid sodium chloride when it is paired with starvation. This behavior may help animals avoid areas without food. While some genes have been implicated in this salt aversive learning behavior, critical genetic components, and the neural circuit in which they act, remain elusive. Here, we show that the sole worm ortholog of mammalian CaMKI/IV, CMK-1, is essential for salt aversive learning behavior in C. elegans hermaphrodites. We find that CMK-1 acts in the primary salt-sensing ASE neurons to regulate this behavior. By characterizing the intracellular calcium dynamics in ASE neurons using microfluidics, we find that loss of cmk-1 has subtle effects on sensory-evoked calcium responses in ASE axons and their modulation by salt conditioning. Our study implicates the expression of the conserved CaMKI/CMK-1 in chemosensory neurons as a regulator of behavioral plasticity to environmental salt in C. elegans SIGNIFICANCE STATEMENT Like other animals, the nematode Caenorhabditis elegans depends on salt for survival and navigates toward high concentrations of this essential mineral. Besides its role as an essential nutrient, salt also causes osmotic stress at high concentrations. A growing body of evidence indicates that C. elegans balances the requirement for salt with the danger it presents through a process called salt aversive learning. We show that this behavior depends on expression of a calcium/calmodulin-dependent kinase, CMK-1, in the ASE salt sensing neurons. Our study identifies CMK-1 and salt-sensitive chemosensory neurons as key factors in this form of behavioral plasticity. Copyright © 2018 the authors.

Genetic analysis in Bartter syndrome from India.

PubMed

Sharma, Pradeep Kumar; Saikia, Bhaskar; Sharma, Rachna; Ankur, Kumar; Khilnani, Praveen; Aggarwal, Vinay Kumar; Cheong, Hae

2014-10-01

Bartter syndrome is a group of inherited, salt-losing tubulopathies presenting as hypokalemic metabolic alkalosis with normotensive hyperreninemia and hyperaldosteronism. Around 150 cases have been reported in literature till now. Mutations leading to salt losing tubulopathies are not routinely tested in Indian population. The authors have done the genetic analysis for the first time in the Bartter syndrome on two cases from India. First case was antenatal Bartter syndrome presenting with massive polyuria and hyperkalemia. Mutational analysis revealed compound heterozygous mutations in KCNJ1(ROMK) gene [p(Leu220Phe), p(Thr191Pro)]. Second case had a phenotypic presentation of classical Bartter syndrome however, genetic analysis revealed only heterozygous novel mutation in SLC12A gene p(Ala232Thr). Bartter syndrome is a clinical diagnosis and genetic analysis is recommended for prognostication and genetic counseling.

Structural characteristics of alkaline phosphatase from the moderately halophilic bacterium Halomonas sp. 593

DOE Office of Scientific and Technical Information (OSTI.GOV)

Arai, Shigeki; Yonezawa, Yasushi; Ishibashi, Matsujiro

2014-03-01

In order to clarify the structural basis of the halophilic characteristics of an alkaline phosphatase derived from the moderate halophile Halomonas sp. 593 (HaAP), the tertiary structure of HaAP was determined to 2.1 Å resolution by X-ray crystallography. The structural properties of surface negative charge and core hydrophobicity were shown to be intermediate between those characteristic of halophiles and non-halophiles, and may explain the unique functional adaptation to a wide range of salt concentrations. Alkaline phosphatase (AP) from the moderate halophilic bacterium Halomonas sp. 593 (HaAP) catalyzes the hydrolysis of phosphomonoesters over a wide salt-concentration range (1–4 M NaCl). Inmore » order to clarify the structural basis of its halophilic characteristics and its wide-range adaptation to salt concentration, the tertiary structure of HaAP was determined by X-ray crystallography to 2.1 Å resolution. The unit cell of HaAP contained one dimer unit corresponding to the biological unit. The monomer structure of HaAP contains a domain comprised of an 11-stranded β-sheet core with 19 surrounding α-helices similar to those of APs from other species, and a unique ‘crown’ domain containing an extended ‘arm’ structure that participates in formation of a hydrophobic cluster at the entrance to the substrate-binding site. The HaAP structure also displays a unique distribution of negatively charged residues and hydrophobic residues in comparison to other known AP structures. AP from Vibrio sp. G15-21 (VAP; a slight halophile) has the highest similarity in sequence (70.0% identity) and structure (C{sup α} r.m.s.d. of 0.82 Å for the monomer) to HaAP. The surface of the HaAP dimer is substantially more acidic than that of the VAP dimer (144 exposed Asp/Glu residues versus 114, respectively), and thus may enable the solubility of HaAP under high-salt conditions. Conversely, the monomer unit of HaAP formed a substantially larger hydrophobic interior comprising 329 C atoms from completely buried residues, whereas that of VAP comprised 264 C atoms, which may maintain the stability of HaAP under low-salt conditions. These characteristics of HaAP may be responsible for its unique functional adaptation permitting activity over a wide range of salt concentrations.« less

Modeling Thermal Changes at Municipal Solid Waste Landfills: A Case Study of the Co-Disposal of Secondary Aluminum Processing Waste

EPA Science Inventory

The reaction of secondary aluminum processing waste (referred herein to as salt cake) with water has been documented to produce heat and gases such as hydrogen, methane, and ammonia (US EPA 2015). The objective of this project was to assess the impact of salt cake disposal on MS...

Bioavailability of iodine and hardness (magnesium and calcium salt) in drinking water in the etiology of endemic goitre in Sundarban delta of West Bengal (India).

PubMed

Chandra, Amar K; Tripathy, Smritiratan; Debnath, Arijit; Ghosh, Dishari

2007-04-01

Endemic goitre has been reported from the ecologically diverse Sundarban delta of West Bengal (India). To study the etiological factors for the persistence of endemic goitre, bioavailability of iodine and hardness of water used for drinking in the region were evaluated because these common environmental factors are inversely and directly related with goitre prevalence in several geographical regions. For the present study from 19 Community Development Blocks of Sundarban delta, 19 areas were selected at random. From each area at least 8 drinking water samples were collected and analyzed for iodine and the hardness (calcium and magnesium salt content). Iodine content in the drinking water samples was found in the range from 21 to 119 mg/L and total hardness of drinking water was found to range from 50 to 480 ppm. Presence of magnesium salt was found higher than the calcium salts in most of the samples. These findings suggest that the entire delta region is environmentally iodine sufficient but water is relatively hard and thus possibility of hardness of water for the persistence of endemic goitre may not be ruled out.

Pairing Heterocyclic Cations with closo-dodecafluorododecaborate (2-) Synthesis of Binary Heterocyclium (1+) Salts and a Ag4(heterocycle)8(4+) Salt of B12F12(2-)

DTIC Science & Technology

2011-01-01

10989). 13. SUPPLEMENTARY NOTES Journal article published in the Journal of Fluorine Chemistry, Vol. 132, Nov 2011. PA Case Number: 10989...TELEPHONE NUMBER (include area code) N/A Standard Form 298 (Rev. 8-98) Prescribed by ANSI Std. 239.18 Journal of Fluorine Chemistry 132 (2011... Fluorine Chemistry jo ur n al h o mep ag e: www .e lsev ier . c om / loc ate / f luo r1. Introduction Eight new binary salts that pair the icosahedral

Proposed Great Salt Lake Basin Hydrologic Observatory

NASA Astrophysics Data System (ADS)

Johnson, W. P.; Tarboton, D. G.

2004-12-01

The dynamic physiography and population growth within the Great Salt Lake Basin provide the opportunity to observe climate and human-induced land-surface changes affecting water availability, water quality, and water use, thereby making the Great Salt Lake Basin a microcosm of contemporary water resource issues and an excellent site to pursue interdisciplinary and integrated hydrologic science. Important societal concerns center on: How do climate variability and human-induced landscape changes affect hydrologic processes, water quality and availability, and aquatic ecosystems over a range of scales? What are the resource, social, and economic consequences of these changes? The steep topography and large climatic gradients of the Great Salt Lake Basin yield hydrologic systems that are dominated by non-linear interactions between snow deposition and snow melt in the mountains, stream flow and groundwater recharge in the mid-elevations, and evaporative losses from the desert floor at lower elevations. Because the Great Salt Lake Basin terminates in a closed basin lake, it is uniquely suited to closing the water, solute, and sediment balances in a way that is rarely possible in a watershed of a size sufficient for coupling to investigations of atmospheric processes. Proposed infrastructure will include representative densely instrumented focus areas that will be nested within a basin-wide network, thereby quantifying fluxes, residence times, pathways, and storage volumes over a range of scales and land uses. The significant and rapid ongoing urbanization presents the opportunity for observations that quantify the interactions among hydrologic processes, human induced changes and social and economic dynamics. One proposed focus area will be a unique, highly instrumented mountain-to-basin transect that will quantify hydrologic processes extending from the mountain ridge top to the Great Salt Lake. The transect will range in elevation from about 1200 m to 3200 m, with a corresponding range in precipitation from about 15 cm/yr to 150 cm/yr, range in evapotranspiration regimes from semi-arid to alpine, range in groundwater residence times from 10 to 10,000 years, and ranges in biome type from semi-arid shrubland to alpine tundra, all within a 30 km distance. Atmospheric and surface fluxes and stores (precipitation, evapotranspiration, snow, soil moisture) will be quantified using an array of in-situ surface stations and remote sensing platforms. Deep (greater than 300 m) multilevel sampling wells will be used to measure ground water levels, fluxes, and for sampling of age dating and environmental tracers. Another proposed focus effort will involve lake sediment core analyses complemented by monitoring of dissolved and suspended constituents in surrounding tributaries, to provide a basis for examination of closed basin lakes as integrators and recorders of biogeochemical signals that would otherwise not be discerned based on discreet measurements made in individual tributary watersheds. Core-derived climate and contaminant-nutrient trends through time will be investigated at locations distributed from the top to the bottom of the hydrologic system.

Ionic Liquids in HPLC and CE: A Hope for Future.

PubMed

Ali, Imran; Suhail, Mohd; Sanagi, Mohd Marsin; Aboul-Enein, Hassan Y

2017-07-04

The ionic liquids (ILs) are salts with melting points below 100°C. These are called as ionic fluids, ionic melts, liquid electrolytes, fused salts, liquid salts, ionic glasses, designer solvents, green solvents and solvents of the future. These have a wide range of applications, including medical, pharmaceutical and chemical sciences. Nowadays, their use is increasing greatly in separation science, especially in chromatography and capillary electrophoresis due to their remarkable properties. The present article describes the importance of ILs in high-performance liquid chromatography and capillary electrophoresis. Efforts were also made to highlight the future expectations of ILs.

Critical bifurcation of shallow microtidal landforms in tidal flats and salt marshes

PubMed Central

Fagherazzi, Sergio; Carniello, Luca; D'Alpaos, Luigi; Defina, Andrea

2006-01-01

Shallow tidal basins are characterized by extensive tidal flats and salt marshes that lie within specific ranges of elevation, whereas intermediate elevations are less frequent in intertidal landscapes. Here we show that this bimodal distribution of elevations stems from the characteristics of wave-induced sediment resuspension and, in particular, from the reduction of maximum wave height caused by dissipative processes in shallow waters. The conceptual model presented herein is applied to the Venice Lagoon, Italy, and demonstrates that areas at intermediate elevations are inherently unstable and tend to become either tidal flats or salt marshes. PMID:16707583

Listeria: A foodborne pathogen that knows how to survive.

PubMed

Gandhi, Megha; Chikindas, Michael L

2007-01-01

The foodborne pathogen Listeria is the causative agent of listeriosis, a severe disease with high hospitalization and case fatality rates. Listeria monocytogenes can survive and grow over a wide range of environmental conditions such as refrigeration temperatures, low pH and high salt concentration. This allows the pathogen to overcome food preservation and safety barriers, and pose a potential risk to human health. This review focuses on the key issues such as survival of the pathogen in adverse environments, and the important adaptation and survival mechanisms such as biofilm formation, quorum sensing and antimicrobial resistance. Studies on the development of technologies to prevent and control L. monocytogenes contamination in foods and food processing facilities are also discussed.

Seasonal Freshwater and Salinity Budgets in the Tropical Atlantic Ocean

NASA Astrophysics Data System (ADS)

Yoo, Jung Moon

Seasonal freshwater and salt budgets in the tropical Atlantic are examined by incorporating precipitation, estimated from 11 years of outgoing longwave radiation (OLR) data. A spatially dependent formula is developed to estimate rainfall from the OLR data and the height of the base of the trade -wind inversion. This formula has been constructed by comparing rainfall records from twelve islands with the OLR data. Zonal asymmetries due to the differing cloud types in the eastern and western Atlantic and the presence of Saharan sand in the east are included. Significant inconsistencies between results of the present study the seasonal rainfall estimates of Dorman and Bourke (1981) are found. Annual and interannual variations of the moisture and freshwater budgets are examined in the same region. The seasonal moisture budget (E-P) is calculated from the above rainfall and evaporation estimated from surface data. Consistent with previous estimates, we find annual mean deficit of freshwater. The interannual variability of freshwater flux during the period 1974 to 1979 is examined. Seasonal or interannua1 variations of rainfall account for two-thirds of the variations of the freshwater flux. We examine the seasonal freshwater and salt budgets, and obtain their meridional transports by southward integration of their divergence fields. The annual freshwater transport in the tropical Atlantic is northward, ranging from 0 Sv near the equator to 0.3 Sv at 12^circ N and 20^circS. The seasonal meridional transport amounts of freshwater from surface to 500 m depth in the tropical Atlantic Ocean range from 1.35 Sv to -0.45 Sv. The strong northward freshwater transports prevail for the period summer to fall. This seasonal cycle is caused by the shifts of the ITCZ as well as the changes in the local freshwater storage. Annual and seasonal salt budgets are calculated from objectively analyzed historical (1900-1986) salinity observations. The annual salt flux in the tropical Atlantic is zero, showing that the salt flux by horizontal advection balances the flux by horizontal diffusion. The salt flux due to the diffusion is northward, and has a maximum of 5 times 10^6kg/s at 15^circN. Seasonal transport amounts of salt range from 30 times 10^6 kg/s to -35 times 10^6kg/s. The direction of the seasonal salt transports in the tropical Atlantic is northward except for the period summer to fall. We find an interannual variability of salinity along the coast of South America in the western Atlantic.

Selection for salt tolerance in tidal freshwater swamp species: Advances using baldcypress as a model for restoration: Chapter 14

USGS Publications Warehouse

Krauss, Ken W.; Chambers, Jim L.; Creech, David L.

2007-01-01

Worldwide, the intrusion of salinity into irrigated and natural landscapes has major economic and cultural impacts and has resulted in large reductions in crop yields (Epstein et al. 1980; Flowers 2003). Losses have prompted wide-scale programs to improve the salt tolerance of many agronomic species or to identify crop species that can tolerate lands affected by low levels of salinity. Few historic research efforts have considered forest tree species in the United States, especially in nonurban areas. Newer programs have focused on identifying salt tolerance in forest tree species but have mainly limited these efforts to compiling lists of salt tolerant species to be used in afforestation projects (Gogate et al. 1984; Shrivastava et al. 1988; Beckmann 1991; Bell 1999). Gogate et al. (1984), for instance, listed 26 potential species from Australia with silvicultural application to salt affected lands in India. More comprehensive efforts have considered species lists along with specific site requirements (Bell 1999); species tolerant to saline irrigation waters on dry land, for example, will not often be tolerant of salinity increases in wetland settings. Similar ideas have spawned field trials of native and nonnative tree species in India, Pakistan, Thailand, Australia, and the United States (Thomson 1988; Beckmann 1991; Krauss et al. 2000; Conner and Ozalp 2002; Marcar and Crawford 2004; Conner and Inabinette 2005). Concerted attempts at salt tolerance improvement of forest tree species have been limited, owing in part to the diversity of regional issues that such programs must consider. Whereas food, fodder, and pulp yield may be the major improvement goal on salt affected lands in India (Mathur and Sharma 1984), identifying trees that can survive deicing salts (Townsend 1989), oil and gas brine discharges (Auchmoody and Walters 1988), or sea-level rise induced salinity changes (Pezeshki et al. 1987, 1990) are of greater interest to larger industrial nations. Nevertheless, salt tolerance research on a range of tree species has converged on one very important finding; among the mechanisms proposed for salt tolerance in nonhalophytes (Greenway and Munns 1980; Munns and Termaat 1986; Cheeseman 1988), ion exclusion from cellular processes, especially exclusion of Cl- , ranks high (Townsend 1989). Identifying the principal mechanism and location of ion exclusion and determining the range of additive genetic variation available among physiological, morphological, and growth attributes for individual species have been the major elements of salt tolerance improvement programs for trees (Allen et al. 1994a).

Unsupervised detection of salt marsh platforms: a topographic method

NASA Astrophysics Data System (ADS)

Goodwin, Guillaume C. H.; Mudd, Simon M.; Clubb, Fiona J.

2018-03-01

Salt marshes filter pollutants, protect coastlines against storm surges, and sequester carbon, yet are under threat from sea level rise and anthropogenic modification. The sustained existence of the salt marsh ecosystem depends on the topographic evolution of marsh platforms. Quantifying marsh platform topography is vital for improving the management of these valuable landscapes. The determination of platform boundaries currently relies on supervised classification methods requiring near-infrared data to detect vegetation, or demands labour-intensive field surveys and digitisation. We propose a novel, unsupervised method to reproducibly isolate salt marsh scarps and platforms from a digital elevation model (DEM), referred to as Topographic Identification of Platforms (TIP). Field observations and numerical models show that salt marshes mature into subhorizontal platforms delineated by subvertical scarps. Based on this premise, we identify scarps as lines of local maxima on a slope raster, then fill landmasses from the scarps upward, thus isolating mature marsh platforms. We test the TIP method using lidar-derived DEMs from six salt marshes in England with varying tidal ranges and geometries, for which topographic platforms were manually isolated from tidal flats. Agreement between manual and unsupervised classification exceeds 94 % for DEM resolutions of 1 m, with all but one site maintaining an accuracy superior to 90 % for resolutions up to 3 m. For resolutions of 1 m, platforms detected with the TIP method are comparable in surface area to digitised platforms and have similar elevation distributions. We also find that our method allows for the accurate detection of local block failures as small as 3 times the DEM resolution. Detailed inspection reveals that although tidal creeks were digitised as part of the marsh platform, unsupervised classification categorises them as part of the tidal flat, causing an increase in false negatives and overall platform perimeter. This suggests our method may benefit from combination with existing creek detection algorithms. Fallen blocks and high tidal flat portions, associated with potential pioneer zones, can also lead to differences between our method and supervised mapping. Although pioneer zones prove difficult to classify using a topographic method, we suggest that these transition areas should be considered when analysing erosion and accretion processes, particularly in the case of incipient marsh platforms. Ultimately, we have shown that unsupervised classification of marsh platforms from high-resolution topography is possible and sufficient to monitor and analyse topographic evolution.

Molten salts and energy related materials.

PubMed

Fray, Derek

2016-08-15

Molten salts have been known for centuries and have been used for the extraction of aluminium for over one hundred years and as high temperature fluxes in metal processing. This and other molten salt routes have gradually become more energy efficient and less polluting, but there have been few major breakthroughs. This paper will explore some recent innovations that could lead to substantial reductions in the energy consumed in metal production and in carbon dioxide production. Another way that molten salts can contribute to an energy efficient world is by creating better high temperature fuel cells and novel high temperature batteries, or by acting as the medium that can create novel materials that can find applications in high energy batteries and other energy saving devices, such as capacitors. Carbonate melts can be used to absorb carbon dioxide, which can be converted into C, CO and carbon nanoparticles. Molten salts can also be used to create black silicon that can absorb more sunlight over a wider range of wavelengths. Overall, there are many opportunities to explore for molten salts to play in an efficient, low carbon world.

Optimal aluminum/zirconium: Protein interactions for predicting antiperspirant efficacy using zeta potential measurements.

PubMed

Yuan, Shaotang; Vaughn, John; Pappas, Iraklis; Fitzgerald, Michael; Masters, James G; Pan, Long

2015-01-01

The interactions between commercial antiperspirant (AP) salts [aluminum chlorohydrate (ACH), activated ACH, aluminum sesquichlorohydrate (ASCH), zirconium aluminum glycine (ZAG), activated ZAG), pure aluminum polyoxocations (Al13-mer, Al30-mer), and the zirconium(IV)-glycine complex Zr6 (O)4 (OH)4 (H2O)8 (Gly)8]12+(-) (CP-2 or ZG) with Bovine serum albumin (BSA) were studied using zeta potential and turbidity measurements. The maximal turbidity, which revealed the optimal interactions between protein and metal salts, for all protein-metal salt samples was observed at the isoelectric point (IEP), where the zeta potential of the solution was zero. Efficacy of AP salts was determined via three parameters: the amount of salt required to flocculate BSA to reach IEP, the turbidity of solution at the IEP, and the pH range over which the turbidity of the solution remains sufficiently high. By comparing active salt performance from this work to traditional prescreening methods, this methodology was able to provide a consistent efficacy assessment for metal actives in APs or in water treatment.

Great Salt Lake, Utah

USGS Publications Warehouse

Stephens, Doyle W.; Gardner, Joe F.

1999-01-01

This document is intended as a source of general information and facts about Great Salt Lake, Utah. This U.S. Geological Survey information sheet answers frequently asked questions about Great Salt Lake. Topics include: History, salinity, brine shrimp, brine flies, migratory birds, and recreation. Great Salt Lake, the shrunken remnant of prehistoric Lake Bonneville, has no outlet. Dissolved salts accumulate in the lake by evaporation. Salinity south of the causeway has ranged from 6 percent to 27 percent over a period of 22 years (2 to 7 times saltier than the ocean). The high salinity supports a mineral industry that extracts about 2 million tons of salt from the lake each year. The aquatic ecosystem consists of more than 30 species of organisms. Harvest of its best-known species, the brine shrimp, annually supplies millions of pounds of food for the aquaculture industry worldwide. The lake is used extensively by millions of migratory and nesting birds and is a place of solitude for people. All this occurs in a lake that is located at the bottom of a 35,000-square-mile drainage basin that has a human population of more than 1.5 million.

Optimizing a readout protocol for low dose retrospective OSL-dosimetry using household salt.

PubMed

Christiansson, Maria; Mattsson, Sören; Bernhardsson, Christian; Rääf, Christopher L

2012-06-01

The authors' aim has been to find a single aliquot regenerative dose (SAR) protocol that accurately recovers an unknown absorbed dose in the region between 1-250 mGy in household salt. The main investigation has been conducted on a specific mine salt (>98.5% NaCl) intended for household use, using optical stimulation by blue LED (λ = 462 nm). The most accurate dose recovery for this brand of salt is found to be achieved when using Peak Signal Summing (PSS) of the OSL-decay and a preheat temperature of 200°C after the test dose. A SAR protocol for the household salt with preset values of regenerative doses (R1--R5) and a test dose (TED) of 17 mGy is also suggested here. Under laboratory conditions, the suggested protocol recovers unknown absorbed doses in this particular brand within 5% (2 SD) in the dose range between 1-250 mGy. This is a very promising result for low dose applications of household salt as a retrospective dosimeter after a nuclear or radiological event.

Room-temperature ionic liquids enhanced green synthesis of β-glycosyl 1-ester.

PubMed

Cui, Yanli; Xu, Minghan; Yao, Weirong; Mao, Jianwei

2015-04-30

We herein report an efficient synthesis of β-glycosyl 1-ester in room-temperature ionic liquids (RTILs) promoted via silver salt and quaternary ammonium salt (PTC) with good or excellent yields. All products were isolated exclusively as the β-anomers. Four different RTILs, eight metal salts and four quaternary ammonium salts were screened in the glycosylation reaction. The synergistic effect of C6mim·OTf, Ag2O and tetrabutylammonium iodine gave the best results. Their promotion to the system was integral. Thorough study provided insight into the catalytic activity of ionic liquid structure, metal salts and quaternary ammonium salt to these reactions. It is worth mentioning that the yield of aliphatic compound 2,3,4,6-tetra-O-acetyl-β-D-galactopyranosyl butyrate (3l) was highly improved when using C6mim·OTf as solvent compared with the normal volatile solvents under the same catalysts. This green approach has been proved to be practical and compatible with a wide range from aliphatic to aromatic substrates. Copyright © 2015 Elsevier Ltd. All rights reserved.

Log analysis of six boreholes in conjunction with geologic characterization above and on top of the Weeks Island Salt Dome

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sattler, A.R.

1996-06-01

Six boreholes were drilled during the geologic characterization and diagnostics of the Weeks Island sinkhole that is over the two-tiered salt mine which was converted for oil storage by the U.S. Strategic Petroleum Reserve. These holes were drilled to provide for geologic characterization of the Weeks Island Salt Dome and its overburden in the immediate vicinity of the sinkhole (mainly through logs and core); to establish a crosswell configuration for seismic tomography; to establish locations for hydrocarbon detection and tracer injection; and to provide direct observations of sinkhole geometry and material properties. Specific objectives of the logging program were to:more » (1) identify the top of and the physical state of the salt dome; (2) identify the water table; (3) obtain a relative salinity profile in the aquifer within the alluvium, which ranges from the water table directly to the top of the Weeks Island salt dome; and (4) identify a reflecting horizon seen on seismic profiles over this salt dome. Natural gamma, neutron, density, sonic, resistivity and caliper logs were run.« less

Thermal resistance model for CSP central receivers

NASA Astrophysics Data System (ADS)

de Meyer, O. A. J.; Dinter, F.; Govender, S.

2016-05-01

The receiver design and heliostat field aiming strategy play a vital role in the heat transfer efficiency of the receiver. In molten salt external receivers, the common operating temperature of the heat transfer fluid or molten salt ranges between 285°C to 565°C. The optimum output temperature of 565°C is achieved by adjusting the mass flow rate of the molten salt through the receiver. The reflected solar radiation onto the receiver contributes to the temperature rise in the molten salt by means of heat transfer. By investigating published work on molten salt external receiver operating temperatures, corresponding receiver tube surface temperatures and heat losses, a model has been developed to obtain a detailed thermographic representation of the receiver. The steady state model uses a receiver flux map as input to determine: i) heat transfer fluid mass flow rate through the receiver to obtain the desired molten salt output temperature of 565°C, ii) receiver surface temperatures iii) receiver tube temperatures iv) receiver efficiency v) pressure drop across the receiver and vi) corresponding tube strain per panel.

Osmoregulatory function in ducks following ingestion of the organophosphorus insecticide fenthion

USGS Publications Warehouse

Rattner, B.A.; Fleming, W.J.; Murray, H.C.

1983-01-01

Salt gland function and osmoregulation in aquatic birds drinking hyperosmotic water has been suggested to be impaired by organophosphorus insecticides. To test this hypothesis, adult black ducks (Anas rubripes) were provided various regimens of fresh or salt (1.5% NaCl) water before, during, and after ingestion of mash containing 21 ppm fenthion. Ducks were bled by jugular venipuncture after I, 7. and 12 days of treatment, and were then killed. Brain and salt gland acetylcholinesterase activities were substantially inhibited (44-61% and 14-36%) by fenthion. However, salt gland weight and Na + -K + -ATPase activity, and plasma Na + , CI- , and osmolality, were uniformly elevated in all groups receiving salt water including those ingesting fenthion. In a second study, salt gland Na + -K + -ATPase activity in mallards (A. platyrhynchos) was not affected after in vitro incubation with either fenthion or fenthion oxon at concentrations ranging from 0.04 to 400 ?M, but was reduced in the presence of 40 and 400 ?M DDE (positive control). These findings suggest that environmentally realistic concentrations of organophosphorus insecticides do not markedly affect osmoregulatory function in adult black ducks.

Liver transplant associated with paracetamol overdose: results from the seven-country SALT study

PubMed Central

Gulmez, Sinem Ezgi; Larrey, Dominique; Pageaux, Georges-Philippe; Bernuau, Jacques; Bissoli, Franco; Horsmans, Yves; Thorburn, Douglas; McCormick, P Aiden; Stricker, Bruno; Toussi, Massoud; Lignot-Maleyran, Séverine; Micon, Sophie; Hamoud, Fatima; Lassalle, Régis; Jové, Jérémy; Blin, Patrick; Moore, Nicholas

2015-01-01

Aims Acute drug overdose, especially with paracetamol, may cause acute liver failure leading to registration for transplantation (ALFT). Population statistics and between-country differences for ALFT related to overdose have been poorly described. The aim of the present study was to evaluate overdose ALFT in the multi-country Study of Acute Liver Transplantation (SALT). Methods All adult overdose-related ALFT, with or without suicidal intent, in France, Greece, Ireland, Italy, the Netherlands, Portugal and the UK between 2005 and 2007 were identified from liver transplant registries and hospital records. These were compared with whole-country and per capita use of paracetamol. Results Six hundred cases of ALFT were identified in 52 of 57 eligible transplant centres, of which 114 involved overdose (72 intentional, 10 non-intentional, 32 uncertain). Overdose represented 20% of all-cause ALFT: Ireland 52%, UK 28%, France 18%, the Netherlands 8%, and Italy 1%. Overdose ALFT were mostly females (61%), mean age 33.6 ± 10.9 years. A total of 111 (97%) of the overdoses involved paracetamol. Event rates ranged from one ALFT for 20.7 tons of paracetamol in Ireland, to one for 1074 tons in Italy and one case in 60 million inhabitants over 3 years in Italy to one case in 286 000 inhabitants per year in Ireland. Per-country event rates for non-overdose ALFT exposed to paracetamol were between 2.5 and 4.0 per million treatment-years sold. Conclusions Paracetamol overdose was found to represent one-sixth of all-cause ALFT. There was a 50-fold difference in Europe in the rates of paracetamol overdose ALFT, and a 200-fold difference per million inhabitants. PMID:26017643

Liver transplant associated with paracetamol overdose: results from the seven-country SALT study.

PubMed

Gulmez, Sinem Ezgi; Larrey, Dominique; Pageaux, Georges-Philippe; Bernuau, Jacques; Bissoli, Franco; Horsmans, Yves; Thorburn, Douglas; McCormick, P Aiden; Stricker, Bruno; Toussi, Massoud; Lignot-Maleyran, Séverine; Micon, Sophie; Hamoud, Fatima; Lassalle, Régis; Jové, Jérémy; Blin, Patrick; Moore, Nicholas

2015-09-01

Acute drug overdose, especially with paracetamol, may cause acute liver failure leading to registration for transplantation (ALFT). Population statistics and between-country differences for ALFT related to overdose have been poorly described. The aim of the present study was to evaluate overdose ALFT in the multi-country Study of Acute Liver Transplantation (SALT). All adult overdose-related ALFT, with or without suicidal intent, in France, Greece, Ireland, Italy, the Netherlands, Portugal and the UK between 2005 and 2007 were identified from liver transplant registries and hospital records. These were compared with whole-country and per capita use of paracetamol. Six hundred cases of ALFT were identified in 52 of 57 eligible transplant centres, of which 114 involved overdose (72 intentional, 10 non-intentional, 32 uncertain). Overdose represented 20% of all-cause ALFT: Ireland 52%, UK 28%, France 18%, the Netherlands 8%, and Italy 1%. Overdose ALFT were mostly females (61%), mean age 33.6 ± 10.9 years. A total of 111 (97%) of the overdoses involved paracetamol. Event rates ranged from one ALFT for 20.7 tons of paracetamol in Ireland, to one for 1074 tons in Italy and one case in 60 million inhabitants over 3 years in Italy to one case in 286 000 inhabitants per year in Ireland. Per-country event rates for non-overdose ALFT exposed to paracetamol were between 2.5 and 4.0 per million treatment-years sold. Paracetamol overdose was found to represent one-sixth of all-cause ALFT. There was a 50-fold difference in Europe in the rates of paracetamol overdose ALFT, and a 200-fold difference per million inhabitants. © 2015 The British Pharmacological Society.

Corrosion fatigue in nitrocarburized quenched and tempered steels

DOE Office of Scientific and Technical Information (OSTI.GOV)

Karim Khani, M.; Dengel, D.

1996-05-01

In order to investigate the fatigue strength and fracture mechanism of salt bath nitrocarburized steels, specimens of the steels SAE 4135 and SAE 4140, in a quenched and tempered state, and additionally in a salt bath nitrocarburized and oxidizing cooled state as well as in a polished (after the oxidizing cooling) and renewed oxidized state, were subjected to comparative rotating bending fatigue tests in inert oil and 5 pct NaCl solution. In addition, some of the quenched and tempered specimens of SAE 4135 material were provided with an approximately 50-{mu}m-thick electroless Ni-P layer, in order to compare corrosion fatigue behaviormore » between the Ni-P layer and the nitride layers. Long-life corrosion fatigue tests of SAE 4135 material were carried out under small stresses in the long-life range up to 10{sup 8} cycles with a test frequency of 100 Hz. Fatigue tests of SAE 4140 material were carried out in the range of finite life (low-cycle range) with a test frequency of 13 Hz. The results show that the 5 pct NaCl environment drastically reduced fatigue life, but nitrocarburizing plus oxidation treatment was found to improve the corrosion fatigue life over that of untreated and Ni-P coated specimens. The role of inclusions in initiating fatigue cracks was investigated. It was found that under corrosion fatigue conditions, the fatigue cracks started at cavities along the interfaces of MnS inclusions and matrix in the case of quenched and tempered specimens. The nitrocarburized specimens, however, showed a superposition of pitting corrosion and corrosion fatigue in which pores and nonmetallic inclusions in the compound layer play a predominant role concerning the formation of pits in the substrate.« less

Anthropogenic salts from deteriorated stones of a historical monument (Kraków, Poland)

NASA Astrophysics Data System (ADS)

Marszałek, Mariola; Prajer, Marta

2017-04-01

The results focus on the stone architectonic elements of the Hebdowski Palace in the Okół, an old, medieval part of Kraków. The object was built around 1400, then rebuilt at the turn of the 17th century and at the first half of the 19th century. Its façade was covered with plaster, whose scaling fragments prior to the renovation in 2015 revealed underneath bricks, particularly in the lower part of the palace. The sandstone elements were used in the main portal, while the limestone ones in window frames of the lower section of the façade, base mouldings, and the buttresses at the corner of Poselska and Senacka streets (one of the oldest streets in Kraków). The stone blocks show various forms of damage, ranging from the accumulation of black crusts and efflorescences to crumbling and scaling of their surfaces. Optical microscopy, scanning electron microscopy (SEM-EDS), micro-Raman spectroscopy and X-ray diffractometry (XRD) were used for analysing deterioration products of the stone samples that were collected during the restoration campaign of 2015. The salt minerals detected in the efflorescences and the black crusts include mainly gypsum CaSO4•2H2O and halite NaCl. On the surface of the limestone gypsum is accompanied by oxalates (whewellite CaC2O4•H2O and/or weddellite CaC2O4•2H2O). The black crust developed on both stone types also contain numerous dust particles and a carbonaceous matter, probably soot. The origin of the anthropogenic salts can be mainly assigned to air pollution, to the stones themselves (mainly in the case of the limestone), and to migration of ions from some elements of the façade (e.g. plaster) in the case of the sandstone. The chemicals used for removing ice from streets and pavements (chiefly NaCl and CaCl2) also seem to be important in the formations of the salts. Finally, the existence of simple life forms, such as lichens and fungi, could result in the precipitation of oxalates. This work has been financially supported by AGH University of Science and Technology (statutory grant No. 11.11.140.319).

Can salt marshes survive sea level rise ?

NASA Astrophysics Data System (ADS)

Tambroni, N.; Seminara, G.

2008-12-01

Stability of salt marshes is a very delicate issue depending on the subtle interplay among hydrodynamics, morphodynamics and ecology. In fact, the elevation of the marsh platform depends essentially on three effects: i) the production of soil associated with sediments resuspended by tidal currents and wind waves in the adjacent tidal flats, advected to the marsh and settling therein; ii) production of organic sediments by the salt marsh vegetation; iii) soil 'loss' driven by sea level rise and subsidence. In order to gain insight into the mechanics of the process, we consider a schematic configuration consisting of a salt marsh located at the landward end of a tidal channel connected at the upstream end with a tidal sea, under different scenarios of sea level rise. We extend the simple 1D model for the morphodynamic evolution of a tidal channel formulated by Lanzoni and Seminara (2002, Journal of Geophysical Research-Oceans, 107, C1) allowing for sediment resuspension in the channel and vegetation growth in the marsh using the depth dependent model of biomass productivity of Spartina proposed by Morris et al. (2002, Ecology, 83, pp. 2869 - 2877). We first focus on the case of a tide dominated salt marsh neglecting wind driven sediment resuspension in the shoal. Results show that the production of biomass plays a crucial role on salt marsh stability and, provided productivity is high enough, it may turn out to be sufficient to counteract the effects of sea level rise even in the absence of significant supply of mineral sediments. The additional effect of wind resuspension is then introduced. Note that the wind action is twofold: on one hand, it generates wind waves the amplitude of which is strongly dependent on shoal depth and wind fetch; on the other hand, it generates currents driven by the surface setup induced by the shear stress acting on the free surface. Here, each contribution is analysed separately. Results show that the values of bottom stress induced by wind setup are small compared with those associated with wind waves. However, the permanence of wind currents makes them as significant as the oscillating tidal currents in determining the direction and the intensity of the residual sediment flux. Marshes are typically characterised by a variety of vegetation species competing for habitat space within the intertidal zone: we analyze this feature by considering the case of two different species. Preliminary results show that the presence of a species characterised by a narrower habitat range, lower optimum elevation and biomass productivity, has a positive feedback on the growth of the other species. Moreover, the presence of an invader raises marsh elevation above the value reached in the presence of just one species. Finally, we investigate the effect of a reduction of the amount of sediments supplied from the sea.

Survey of Materials for Fusion Fission Hybrid Reactors Vol 1 Rev. 0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Farmer, Joseph Collin

2007-07-03

Materials for fusion-fission hybrid reactors fall into several broad categories, including fuels, blanket and coolant materials, cladding, structural materials, shielding, and in the specific case of inertial-confinement fusion systems, laser and optical materials. This report surveys materials in all categories of materials except for those required for lasers and optics. Preferred collants include two molten salt mixtures known as FLIBE (Li2BeF4) and FLINABE (LiNaBeF4). In the case of homogenous liquid fuels, UF4 can be dissolved in these molten salt mixtures. The transmutation of lithium in this coolant produces very corrosive hydrofluoric acid species (HF and TF), which can rapidly degrademore » structural materials. Broad ranges of high-melting radiation-tolerant structural material have been proposed for fusion-fission reactor structures. These include a wide variety of steels and refractory alloys. Ferritic steels with oxide-dispersion strengthening and graphite have been given particular attention. Refractory metals are found in Groups IVB and VB of the periodic table, and include Nb, Ta, Cr, Mo, and W, as serve as the basis of refractory alloys. Stable high-melting composites and amorphous metals may also be useful. Since amorphous metals have no lattice structure, neutron bombardment cannot dislodge atoms from lattice sites, and the materials would be immune from this specific mode of degradation. The free energy of formation of fluorides of the alloying elements found in steels and refractory alloys can be used to determine the relative stability of these materials in molten salts. The reduction of lithium transmutation products (H + and T +) drives the electrochemical corrosion process, and liberates aggressive fluoride ions that pair with ions formed from dissolved structural materials. Corrosion can be suppressed through the use of metallic Be and Li, though the molten salt becomes laden with colloidal suspensions of Be and Li corrosion products in the process. Alternatively, imposed currents and other high-temperature cathodic protection systems are envisioned for protection of the structural materials. This novel concept could prove to be enabling technology for such high-temperature molten-salt reactors. The use of UF 4 as a liquid-phase homogenous fuel is also complicated by redox control. For example, the oxidation of tetravalent uranium to hexavalent uranium could result in the formation of volatile UF 6. This too could be controlled through electrochemically manipulated oxidation and reduction reactions. In situ studies of pertinent electrochemical reactions in the molten salts are proposed, and are relevant to both the corrosive attack of structural materials, as well as the volatilization of fuel. Some consideration is given to the potential advantages of gravity fed falling-film blankets. Such systems may be easier to control than vortex systems, but would require that cylindrical reaction vessels be oriented with the centerline normal to the gravitational field.« less

Salt stress-induced Ca2+ waves are associated with rapid, long-distance root-to-shoot signaling in plants

PubMed Central

Choi, Won-Gyu; Toyota, Masatsugu; Kim, Su-Hwa; Hilleary, Richard; Gilroy, Simon

2014-01-01

Their sessile lifestyle means that plants have to be exquisitely sensitive to their environment, integrating many signals to appropriate developmental and physiological responses. Stimuli ranging from wounding and pathogen attack to the distribution of water and nutrients in the soil are frequently presented in a localized manner but responses are often elicited throughout the plant. Such systemic signaling is thought to operate through the redistribution of a host of chemical regulators including peptides, RNAs, ions, metabolites, and hormones. However, there are hints of a much more rapid communication network that has been proposed to involve signals ranging from action and system potentials to reactive oxygen species. We now show that plants also possess a rapid stress signaling system based on Ca2+ waves that propagate through the plant at rates of up to ∼400 µm/s. In the case of local salt stress to the Arabidopsis thaliana root, Ca2+ wave propagation is channeled through the cortex and endodermal cell layers and this movement is dependent on the vacuolar ion channel TPC1. We also provide evidence that the Ca2+ wave/TPC1 system likely elicits systemic molecular responses in target organs and may contribute to whole-plant stress tolerance. These results suggest that, although plants do not have a nervous system, they do possess a sensory network that uses ion fluxes moving through defined cell types to rapidly transmit information between distant sites within the organism. PMID:24706854

Theory and application of an approximate model of saltwater upconing in aquifers

USGS Publications Warehouse

McElwee, C.; Kemblowski, M.

1990-01-01

Motion and mixing of salt water and fresh water are vitally important for water-resource development throughout the world. An approximate model of saltwater upconing in aquifers is developed, which results in three non-linear coupled equations for the freshwater zone, the saltwater zone, and the transition zone. The description of the transition zone uses the concept of a boundary layer. This model invokes some assumptions to give a reasonably tractable model, considerably better than the sharp interface approximation but considerably simpler than a fully three-dimensional model with variable density. We assume the validity of the Dupuit-Forchheimer approximation of horizontal flow in each layer. Vertical hydrodynamic dispersion into the base of the transition zone is assumed and concentration of the saltwater zone is assumed constant. Solute in the transition zone is assumed to be moved by advection only. Velocity and concentration are allowed to vary vertically in the transition zone by using shape functions. Several numerical techniques can be used to solve the model equations, and simple analytical solutions can be useful in validating the numerical solution procedures. We find that the model equations can be solved with adequate accuracy using the procedures presented. The approximate model is applied to the Smoky Hill River valley in central Kansas. This model can reproduce earlier sharp interface results as well as evaluate the importance of hydrodynamic dispersion for feeding salt water to the river. We use a wide range of dispersivity values and find that unstable upconing always occurs. Therefore, in this case, hydrodynamic dispersion is not the only mechanism feeding salt water to the river. Calculations imply that unstable upconing and hydrodynamic dispersion could be equally important in transporting salt water. For example, if groundwater flux to the Smoky Hill River were only about 40% of its expected value, stable upconing could exist where hydrodynamic dispersion into a transition zone is the primary mechanism for moving salt water to the river. The current model could be useful in situations involving dense saltwater layers. ?? 1990.

Preliminary evaluation of solution-mining intrusion into a salt-dome repository

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1981-06-01

This report is the product of the work of an ONWI task force to evaluate inadvertant human intrusion into a salt dome repository by solution mining. It summarizes the work in the following areas: a general review of the levels of defense that could reduce both the likelihood and potential consequences of human intrusion into a salt dome repository; evaluation of a hypothetical intrusion scenario and its consequences; recommendation for further studies. The conclusions of this task force report can be summarized as follows: (1) it is not possible at present to establish with certainty that solution mining is crediblemore » as a human-intrusion event. The likelihood of such an intrusion will depend on the effectiveness of the preventive measures; (2) an example analysis based on the realistic approach is presented in this report; it concluded that the radiological consequences are strongly dependent upon the mode of radionuclide release from the waste form, time after emplacement, package design, impurities in the host salt, the amount of a repository intercepted, the solution mining cavity form, the length of time over which solution mining occurs, the proportion of contaminated salt source for human consumption compared to other sources, and the method of salt purification for culinary purposes; (3) worst case scenarios done by other studies suggest considerable potential for exposures to man while preliminary evaluations of more realistic cases suggest significantly reduced potential consequences. Mathematical model applications to process systems, guided by more advanced assumptions about human intrusion into geomedia, will shed more light on the potential for concerns and the degree to which mitigative measures will be required.« less

Deep Eutectic Salt Formulations Suitable as Advanced Heat Transfer Fluids

DOE Office of Scientific and Technical Information (OSTI.GOV)

Raade, Justin; Roark, Thomas; Vaughn, John

2013-07-22

Concentrating solar power (CSP) facilities are comprised of many miles of fluid-filled pipes arranged in large grids with reflective mirrors used to capture radiation from the sun. Solar radiation heats the fluid which is used to produce steam necessary to power large electricity generation turbines. Currently, organic, oil-based fluid in the pipes has a maximum temperature threshold of 400 °C, allowing for the production of electricity at approximately 15 cents per kilowatt hour. The DOE hopes to foster the development of an advanced heat transfer fluid that can operate within higher temperature ranges. The new heat transfer fluid, when usedmore » with other advanced technologies, could significantly decrease solar electricity cost. Lower costs would make solar thermal electricity competitive with gas and coal and would offer a clean, renewable source of energy. Molten salts exhibit many desirable heat transfer qualities within the range of the project objectives. Halotechnics developed advanced heat transfer fluids (HTFs) for application in solar thermal power generation. This project focused on complex mixtures of inorganic salts that exhibited a high thermal stability, a low melting point, and other favorable characteristics. A high-throughput combinatorial research and development program was conducted in order to achieve the project objective. Over 19,000 candidate formulations were screened. The workflow developed to screen various chemical systems to discover salt formulations led to mixtures suitable for use as HTFs in both parabolic trough and heliostat CSP plants. Furthermore, salt mixtures which will not interfere with fertilizer based nitrates were discovered. In addition for use in CSP, the discovered salt mixtures can be applied to electricity storage, heat treatment of alloys and other industrial processes.« less

The ebb and flood of Silica: Quantifying dissolved and biogenic silica fluxes from a temperate salt marsh

NASA Astrophysics Data System (ADS)

Vieillard, Amanda M.; Fulweiler, Robinson W.; Hughes, Zoe J.; Carey, Joanna C.

2011-12-01

Salt marshes are widely studied due to the broad range of ecosystem services they provide including serving as crucial wildlife habitat and as hotspots for biogeochemical cycling. Nutrients such as nitrogen (N), phosphorus (P), and carbon (C) are well studied in these systems. However, salt marshes may also be important environments for the cycling of another key nutrient, silica (Si). Found at the land-sea interface, these systems are silica replete with large stocks in plant biomass, sediments, and porewater, and therefore, have the potential to play a substantial role in the transformation and export of silica to coastal waters. In an effort to better understand this role, we measured the fluxes of dissolved (DSi) and biogenic (BSi) silica into and out of two tidal creeks in a temperate, North American (Rowley, Massachusetts, USA) salt marsh. One of the creeks has been fertilized from May to September for six years allowing us to examine the impacts of nutrient addition on silica dynamics within the marsh. High-resolution sampling in July 2010 showed no significant differences in Si concentrations between the fertilized and reference creeks with dissolved silica ranging from 0.5 to 108 μM and biogenic from 2.0 to 56 μM. Net fluxes indicated that the marsh is a point source of dissolved silica to the estuary in the summer with a net flux of approximately 169 mol h -1, demonstrating that this system exports DSi on the same magnitude as some nearby, mid-sized rivers. If these findings hold true for all salt marshes, then these already valuable regions are contributing yet another ecosystem service that has been previously overlooked; by exporting DSi to coastal receiving waters, salt marshes are actively providing this important nutrient for coastal primary productivity.

Earth Observations taken by the Expedition 22 Crew

NASA Image and Video Library

2010-01-31

ISS022-E-058538 (31 Jan. 2010) --- Sir Bani Yas Island is featured in this image photographed by an Expedition 22 crew member on the International Space Station. Sir Bani Yas Island is located in the Persian Gulf near the western coastline of the United Arab Emirates (UAE). The approximately 14-kilometers x nine-kilometers island is the surface expression of a salt dome, and is one of several such islands in the Persian Gulf. During past periods of alternating wet and dry climate, sometimes involving areas with high rates of evaporation in enclosed basins, thick layers of salt minerals (such as halite ? common table salt, or gypsum ? a major component of wallboard) were deposited. These layers were subsequently buried by sediments; with enough overlaying material and depth of burial, the salt layers can begin to flow. Salt has lower density than the surrounding rock and it tends to flow upwards, pushing up the overlaying layers of rock to form a salt dome. While many salt domes retain a cap of the youngest rock layers at the surface, in some cases the underlaying salt extrudes onto the surface. This photograph illustrates the varying character of surfaces on the island. The central mountains of Jebel Wahid (center) mark the location of the Sir Bani Yas salt dome. The dome has breached the surface but exposed salt - primarily gypsum - is removed by erosion, leaving a rugged, insoluble cap formed from fragments of the overlaying sedimentary and volcanic rocks. Sand and silt derived from the Jebel Wahid area and surrounding gravel cover forms beaches along the outer edge of the island.

Origin of salt giants in abyssal serpentinite systems

NASA Astrophysics Data System (ADS)

Scribano, Vittorio; Carbone, Serafina; Manuella, Fabio C.; Hovland, Martin; Rueslåtten, Håkon; Johnsen, Hans-K.

2017-10-01

Worldwide marine salt deposits ranging over the entire geological record are generally considered climate-related evaporites, derived from the precipitation of salts (mainly chlorides and sulfates) from saturated solutions driven by solar evaporation of seawater. This explanation may be realistic for a salt thickness ≤100 m, being therefore inadequate for thicker (>1 km) deposits. Moreover, sub-seafloor salt deposits in deep marine basins are difficult to reconcile with a surface evaporation model. Marine geology reports on abyssal serpentinite systems provide an alternative explanation for some salt deposits. Seawater-driven serpentinization consumes water and increases the salinity of the associated aqueous brines. Brines can be trapped in fractures and cavities in serpentinites and the surrounding `country' rocks. Successive thermal dehydration of buried serpentinites can mobilize and accumulate the brines, forming highly saline hydrothermal solutions. These can migrate upwards and erupt onto the seafloor as saline geysers, which may form salt-saturated water pools, as are currently observed in numerous deeps in the Red Sea and elsewhere. The drainage of deep-seated saline brines to seafloor may be a long-lasting, effective process, mainly occurring in areas characterized by strong tectonic stresses and/or igneous intrusions. Alternatively, brines could be slowly expelled from fractured serpentinites by buoyancy gradients and, hence, separated salts/brines could intrude vertically into surrounding rocks, forming salt diapirs. Serpentinization is an ubiquitous, exothermic, long-lasting process which can modify large volumes of oceanic lithosphere over geological times. Therefore, buried salt deposits in many areas of the world can be reasonably related to serpentinites.

Self-monitoring urinary salt excretion in adults: A novel education program for restricting dietary salt intake

PubMed Central

YASUTAKE, KENICHIRO; SAWANO, KAYOKO; YAMAGUCHI, SHOKO; SAKAI, HIROKO; AMADERA, HATSUMI; TSUCHIHASHI, TAKUYA

2011-01-01

This study aimed to examine the usefulness of the self-monitoring of urinary salt excretion for educating individuals about the risk of excessive dietary salt intake. The subjects were 30 volunteers (15 men and 15 women) not consuming anti-hypertensive medication. The subjects measured urinary salt excretion at home for 4 weeks using a self-monitoring device. Blood pressure (BP), anthropometric variables and nutritional variables (by a dietary-habits questionnaire) were measured before and after the measurement of urinary salt excretion. Statistical analyses were performed, including paired t-tests, Chi-square test, Pearson’s product moment correlation coefficient and multiple linear regression analysis. In all subjects, the average urinary salt excretion over 4 weeks was 8.05±1.61 g/day and the range (maximum-minimum value) was 5.58±2.15 g/day. Salt excretion decreased significantly in weeks 3 and 4 (P<0.05 and P<0.01, respectively). Diastolic BP decreased from 77.7±14.3 (at baseline) to 74.3±13.3 after 4 weeks (P<0.05), while systolic BP and anthropometric variables remained unchanged. Nutrition surveys indicated that energy intake was correlated with salt intake both before and after the measurements; changes in both variables during the observation period were correlated (r=0.40, P<0.05). The percentage of subjects who were aware of the restriction in dietary salt intake increased from 47 to 90%. In conclusion, daily monitoring of the amount of urinary salt excretion using a self-monitoring device appears to be an effective educational tool for improving the quality of life of healthy adults. PMID:22977549

Self-monitoring urinary salt excretion in adults: A novel education program for restricting dietary salt intake.

PubMed

Yasutake, Kenichiro; Sawano, Kayoko; Yamaguchi, Shoko; Sakai, Hiroko; Amadera, Hatsumi; Tsuchihashi, Takuya

2011-07-01

This study aimed to examine the usefulness of the self-monitoring of urinary salt excretion for educating individuals about the risk of excessive dietary salt intake. The subjects were 30 volunteers (15 men and 15 women) not consuming anti-hypertensive medication. The subjects measured urinary salt excretion at home for 4 weeks using a self-monitoring device. Blood pressure (BP), anthropometric variables and nutritional variables (by a dietary-habits questionnaire) were measured before and after the measurement of urinary salt excretion. Statistical analyses were performed, including paired t-tests, Chi-square test, Pearson's product moment correlation coefficient and multiple linear regression analysis. In all subjects, the average urinary salt excretion over 4 weeks was 8.05±1.61 g/day and the range (maximum-minimum value) was 5.58±2.15 g/day. Salt excretion decreased significantly in weeks 3 and 4 (P<0.05 and P<0.01, respectively). Diastolic BP decreased from 77.7±14.3 (at baseline) to 74.3±13.3 after 4 weeks (P<0.05), while systolic BP and anthropometric variables remained unchanged. Nutrition surveys indicated that energy intake was correlated with salt intake both before and after the measurements; changes in both variables during the observation period were correlated (r=0.40, P<0.05). The percentage of subjects who were aware of the restriction in dietary salt intake increased from 47 to 90%. In conclusion, daily monitoring of the amount of urinary salt excretion using a self-monitoring device appears to be an effective educational tool for improving the quality of life of healthy adults.

Signaling mechanisms that link salt retention to hypertension: endogenous ouabain, the Na(+) pump, the Na(+)/Ca(2+) exchanger and TRPC proteins.

PubMed

Blaustein, Mordecai P; Hamlyn, John M

2010-12-01

Salt retention as a result of chronic, excessive dietary salt intake, is widely accepted as one of the most common causes of hypertension. In a small minority of cases, enhanced Na(+) reabsorption by the kidney can be traced to specific genetic defects of salt transport, or pathological conditions of the kidney, adrenal cortex, or pituitary. Far more frequently, however, salt retention may be the result of minor renal injury or small genetic variation in renal salt transport mechanisms. How salt retention actually leads to the increase in peripheral vascular resistance (the hallmark of hypertension) and the elevation of blood pressure remains an enigma. Here we review the evidence that endogenous ouabain (an adrenocortical hormone), arterial smooth muscle α2 Na(+) pumps, type-1 Na/Ca exchangers, and receptor- and store-operated Ca(2+) channels play key roles in the pathway that links salt to hypertension. We discuss cardenolide structure-function relationships in an effort to understand why prolonged administration of ouabain, but not digoxin, induces hypertension, and why digoxin is actually anti-hypertensive. Finally, we summarize recent observations which indicate that ouabain upregulates arterial myocyte Ca(2+) signaling mechanisms that promote vasoconstriction, while simultaneously downregulating endothelial vasodilator mechanisms. In sum, the reports reviewed here provide novel insight into the molecular mechanisms by which salt retention leads to hypertension. Copyright © 2010 Elsevier B.V. All rights reserved.

Salt content in canteen and fast food meals in Denmark.

PubMed

Rasmussen, Lone Banke; Lassen, Anne Dahl; Hansen, Kirsten; Knuthsen, Pia; Saxholt, Erling; Fagt, Sisse

2010-03-16

A high salt (=NaCl) intake is associated with high blood pressure, and knowledge of salt content in food and meals is important, if the salt intake has to be decreased in the general population. To determine the salt content in worksite canteen meals and fast food. For the first part of this study, 180 canteen meals were collected from a total of 15 worksites with in-house catering facilities. Duplicate portions of a lunch meal were collected from 12 randomly selected employees at each canteen on two non-consecutive days. For the second part of the study, a total of 250 fast food samples were collected from 52 retail places representing both city (Aarhus) and provincial towns. The canteen meals and fast food samples were analyzed for chloride by potentiometric titration with silver nitrate solution, and the salt content was estimated. The salt content in lunch meals in worksite canteens were 3.8+/-1.8 g per meal and 14.7+/-5.1 g per 10 MJ for men (n=109), and 2.8+/-1.2 g per meal and 14.4+/-6.2 g per 10 MJ for women (n=71). Salt content in fast food ranged from 11.8+/-2.5 g per 10 MJ (burgers) to 16.3+/-4.4 g per 10 MJ (sausages) with a mean content of 13.8+/-3.8 g per 10 MJ. Salt content in both fast food and in worksite canteen meals is high and should be decreased.

Influence of cyclic annealing on the hardness and structure of high-speed steels

NASA Astrophysics Data System (ADS)

Smol'nikov, E. A.; Orestova, L. M.

1982-08-01

In individual cases with the necessity of rapid annealing of high-speed steel together with stepless annealing at 885-675°C, which is done in a single salt bath, cyclic stepped annealing in two salt baths with temperatures of 850 and 700°C and holds in each of them at from 10 to 30 min may be used.

SALT spectroscopic classification of SN 2017erp as a type-Ia supernova well before maximum light

NASA Astrophysics Data System (ADS)

Jha, S. W.; Camacho, Y.; Dettman, K.; Pan, Y.-C.; Foley, R. J.; Rest, A.; Scolnic, D.; Skelton, R.

2017-06-01

We obtained SALT (+RSS) spectroscopy of SN 2017erp (discovered by K. Itagaki) on 2017 Jun 13.9 UT, covering the wavelength range 350-940 nm. Cross-correlation of the supernova spectrum with a template library using SNID (Blondin & Tonry 2007, ApJ, 666, 1024) shows SN 2017erp is a type-Ia supernova before maximum light.

A one-pot radioiodination of aryl amines via stable diazonium salts: preparation of 125I-imaging agents.

PubMed

Sloan, Nikki L; Luthra, Sajinder K; McRobbie, Graeme; Pimlott, Sally L; Sutherland, Andrew

2017-10-05

An operationally simple, one-pot, two-step tandem procedure that allows the incorporation of radioactive iodine into aryl amines via stable diazonium salts is described. The mild conditions are tolerant of various functional groups and substitution patterns, allowing late-stage, rapid access to a wide range of 125 I-labelled aryl compounds and SPECT radiotracers.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cozzi, A; Cora Berry, C; Michael Bronikowski, M

The decontaminated salt solution waste stream from the Modular Caustic Side Solvent Extraction Unit and the Salt Waste Processing Facility is anticipated to contain entrained extraction solvent. The decontaminated salt solution is scheduled to be processed through Tank 50 into the Saltstone Production Facility. This study, among others, has been undertaken because the solvent concentration in the decontaminated salt solution may cause flammability issues within the Saltstone Disposal Facility that may need to be addressed prior to operation. Previous work at the Savannah River National Laboratory determined the release of Isopar{reg_sign} L from saltstone prepared with a simulated DSS withmore » Isopar{reg_sign} L concentrations ranging from 50 to 200 {micro}g/g in the salt fraction and with test temperatures ranging from ambient to 95 C. The results from the curing of the saltstone showed that the Isopar{reg_sign} L release data can be treated as a percentage of initial concentration in the concentration range studied. The majority of the Isopar{reg_sign} L that was released over the test duration was released in the first few days. The release of Isopar{reg_sign} L begins immediately and the rate of release decreases over time. At higher temperatures the immediate release is larger than at lower temperatures. In this study, saltstone was prepared using a simulated decontaminated salt solution containing Isopar{reg_sign} L concentrations of 50 {micro}L/L (30 {micro}g/g) and 100 {micro}L/L (61 {micro}g/g) and cured at 55 C. The headspace of each sample was purged and the Isopar{reg_sign} L was trapped on a coconut shell carbon tube. The amount of Isopar{reg_sign} L captured was determined using NIOSH Method 1501. The percentage of Isopar{reg_sign} L released after 20 days was 1.4 - 3.7% for saltstone containing 50 {micro}L/L concentration and 2.1 - 4.3% for saltstone containing 100 {micro}L/L concentration. Given the measurement uncertainties in this work there is no clearly discernible relationship between percentage release and initial Isopar{reg_sign} L concentration.« less

Enhanced Microbial Survivability in Subzero Brines.

PubMed

Heinz, Jacob; Schirmack, Janosch; Airo, Alessandro; Kounaves, Samuel P; Schulze-Makuch, Dirk

2018-04-17

It is well known that dissolved salts can significantly lower the freezing point of water and thus extend habitability to subzero conditions. However, most investigations thus far have focused on sodium chloride as a solute. In this study, we report on the survivability of the bacterial strain Planococcus halocryophilus in sodium, magnesium, and calcium chloride or perchlorate solutions at temperatures ranging from +25°C to -30°C. In addition, we determined the survival rates of P. halocryophilus when subjected to multiple freeze/thaw cycles. We found that cells suspended in chloride-containing samples have markedly increased survival rates compared with those in perchlorate-containing samples. In both cases, the survival rates increase with lower temperatures; however, this effect is more pronounced in chloride-containing samples. Furthermore, we found that higher salt concentrations increase survival rates when cells are subjected to freeze/thaw cycles. Our findings have important implications not only for the habitability of cold environments on Earth but also for extraterrestrial environments such as that of Mars, where cold brines might exist in the subsurface and perhaps even appear temporarily at the surface such as at recurring slope lineae. Key Words: Brines-Halophile-Mars-Perchlorate-Subzero-Survival. Astrobiology 18, xxx-xxx.

Stability of polymer encapsulated quantum dots in cell culture media

NASA Astrophysics Data System (ADS)

Ojea-Jiménez, I.; Piella, J.; Nguyen, T.-L.; Bestetti, A.; Ryan, A. D.; Puntes, V.

2013-04-01

The unique optical properties of Quantum Dots have attracted a great interest to use these nanomaterials in diverse biological applications. The synthesis of QDs by methods from the literature permits one to obtain nanocrystals coated by hydrophobic alkyl coordinating ligands and soluble in most of the cases in organic solvents. The ideal biocompatible QD must be homogeneously dispersed and colloidally stable in aqueous solvents, exhibit pH and salt stability, show low levels of nonspecific binding to biological components, maintain a high quantum yield, and have a small hydrodynamic diameter. Polymer encapsulation represents an excellent scaffold on which to build additional biological function, allowing for a wide range of grafting approaches for biological ligands. As these QD are functionalized with poly(ethylene)glycol (PEG) derivatives on their surface, they show long term stability without any significant change in the optical properties, and they are also highly stable in the most common buffer solutions such as Phosphate Buffer Saline (PBS) or borate. However, as biological studies are normally done in more complex biological media which contain a mixture of amino acids, salts, glucose and vitamins, it is essential to determine the stability of our synthesized QDs under these conditions before tackling biological studies.

A data driven model for the impact of IFT and density variations on CO2 sequestration in porous media

NASA Astrophysics Data System (ADS)

Nomeli, Mohammad; Riaz, Amir

2017-11-01

CO2 storage in geological formations is one of the most promising solutions for mitigating the amount of greenhouse gases released into the atmosphere. One of the important issues for CO2 storage in subsurface environments is the sealing efficiency of low-permeable cap-rocks overlying potential CO2 storage reservoirs. A novel model is proposed to find the IFT of the systems (CO2/brine-salt) in a range of temperatures (300-373 K), pressures (50-250 bar), and up to 6 molal salinity applicable to CO2 storage in geological formations through a machine learning-assisted modeling of experimental data. The IFT between mineral surfaces and CO2/brine-salt solutions determines the efficiency of enhanced oil or gas recovery operations as well as our ability to inject and store CO2 in geological formations. Finally, we use the new model to evaluate the effects of formation depth on the actual efficiency of CO2 storage. The results indicate that, in the case of CO2 storage in deep subsurface environments as a global-warming mitigation strategy, CO2 storage capacity are improved with reservoir depth.

Methacrylic Zwitterionic, Thermoresponsive, and Hydrophilic (Co)Polymers via Cu(0)-Polymerization: The Importance of Halide Salt Additives.

PubMed

Simula, Alexandre; Anastasaki, Athina; Haddleton, David M

2016-02-01

The synthesis of hydrophilic, thermoresponsive, and zwitterionic polymethacrylates is reported by Cu(0)-mediated reversible deactivation radical polymerization in water and/or water/alcohol mixtures. The predisproportionation of [Cu(I) (PMDETA)Cl] in water prior to initiator and monomer addition is exploited to yield well-defined polymethacrylates with full monomer conversions in 30 min. The addition of supplementary halide salts (NaCl) enables the synthesis of various molecular weight poly[poly(ethylene glycol) methyl ether methacrylate] (PEGMA475) (DPn = 10-80, Mn ≈ 10,000-40 000 g mol(-1)) with full monomer conversion and narrow molecular weight distributions attained in all cases (Đ ≈ 1.20-1.30). A bifunctional PEG initiator (average Mn ≈ 1000 g mol(-1)) is utilized for the polymerization of a wide range of methacrylates including 2-dimethylaminoethyl methacrylate, 2-morpholinoethyl methacrylate, [2-(methacryloyloxy)ethyl]dimethyl-(3-sulfopropyl)ammonium hydroxide, and 2-methacryloyloxyethyl phosphorylcholine. Despite the high water content, high end group fidelity is demonstrated by in situ chain extensions and block copolymerizations with PEGMA475 yielding well-defined functional telechelic pentablock copolymers within 2.5 h. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Constant-concentration boundary condition: Lessons from the HYDROCOIN variable-density groundwater benchmark problem

USGS Publications Warehouse

Konikow, Leonard F.; Sanford, W.E.; Campbell, P.J.

1997-01-01

In a solute-transport model, if a constant-concentration boundary condition is applied at a node in an active flow field, a solute flux can occur by both advective and dispersive processes. The potential for advective release is demonstrated by reexamining the Hydrologic Code Intercomparison (HYDROCOIN) project case 5 problem, which represents a salt dome overlain by a shallow groundwater system. The resulting flow field includes significant salinity and fluid density variations. Several independent teams simulated this problem using finite difference or finite element numerical models. We applied a method-of-characteristics model (MOCDENSE). The previous numerical implementations by HYDROCOIN teams of a constant-concentration boundary to represent salt release by lateral dispersion only (as stipulated in the original problem definition) was flawed because this boundary condition allows the release of salt into the flow field by both dispersion and advection. When the constant-concentration boundary is modified to allow salt release by dispersion only, significantly less salt is released into the flow field. The calculated brine distribution for case 5 depends very little on which numerical model is used, as long as the selected model is solving the proper equations. Instead, the accuracy of the solution depends strongly on the proper conceptualization of the problem, including the detailed design of the constant-concentration boundary condition. The importance and sensitivity to the manner of specification of this boundary does not appear to have been recognized previously in the analysis of this problem.

Salt tolerance at single cell level in giant-celled Characeae

PubMed Central

Beilby, Mary J.

2015-01-01

Characean plants provide an excellent experimental system for electrophysiology and physiology due to: (i) very large cell size, (ii) position on phylogenetic tree near the origin of land plants and (iii) continuous spectrum from very salt sensitive to very salt tolerant species. A range of experimental techniques is described, some unique to characean plants. Application of these methods provided electrical characteristics of membrane transporters, which dominate the membrane conductance under different outside conditions. With this considerable background knowledge the electrophysiology of salt sensitive and salt tolerant genera can be compared under salt and/or osmotic stress. Both salt tolerant and salt sensitive Characeae show a rise in membrane conductance and simultaneous increase in Na+ influx upon exposure to saline medium. Salt tolerant Chara longifolia and Lamprothamnium sp. exhibit proton pump stimulation upon both turgor decrease and salinity increase, allowing the membrane PD to remain negative. The turgor is regulated through the inward K+ rectifier and 2H+/Cl- symporter. Lamprothamnium plants can survive in hypersaline media up to twice seawater strength and withstand large sudden changes in salinity. Salt sensitive C. australis succumbs to 50–100 mM NaCl in few days. Cells exhibit no pump stimulation upon turgor decrease and at best transient pump stimulation upon salinity increase. Turgor is not regulated. The membrane PD exhibits characteristic noise upon exposure to salinity. Depolarization of membrane PD to excitation threshold sets off trains of action potentials, leading to further loses of K+ and Cl-. In final stages of salt damage the H+/OH- channels are thought to become the dominant transporter, dissipating the proton gradient and bringing the cell PD close to 0. The differences in transporter electrophysiology and their synergy under osmotic and/or saline stress in salt sensitive and salt tolerant characean cells are discussed in detail. PMID:25972875

Evaluation of iodine nutritional status in Tehran, Iran: iodine deficiency within iodine sufficiency.

PubMed

Nazeri, Pantea; Mirmiran, Parvin; Mehrabi, Yadollah; Hedayati, Mehdi; Delshad, Hossein; Azizi, Fereidoun

2010-12-01

Production of iodized salt in Iran for household consumption began in 1990. Previous studies have reported sustainable elimination of iodine deficiency disorders in Iran. The aim of this study was to evaluate the iodine nutritional status in Tehran in 2009. In this cross-sectional study, 383 Tehranian households were enrolled through randomized cluster sampling and a total of 639 adult subjects (242 men and 397 women), aged 19 and over, participated. A 24-hour urine sample was collected for measurement of urinary iodine, sodium, and creatinine concentrations using the digestion method, flame photometry, and autoanalyzer assay, respectively. Salt intake was estimated and iodine content of household salt was measured by titration. Median (interquartile range) iodine content of household salt and urinary iodine concentration (UIC) in Tehran were 21.2 (3.2-31.7) parts per million and 70.0 (34.0-131.2) μg/L, respectively. There was no statistically significant difference in 24-hour UICs between men and women. Median (interquartile range) daily salt intake was 7.6 (5.5-9.8) g, which was not different in the two genders. According to the WHO/ICCIDD/UNICEF classification, 11.2%, 25.9%, 26.7%, 25.1%, 8.0%, and 3.2% of participants had UIC <20, 20-49, 50-99, 100-199, 200-299, and >300 μg/L, respectively. Mild iodine deficiency has recurred in Tehranians. The results emphasize the need for continuous monitoring in all regions, even in a country with iodine sufficiency.

A computational assessment of the permeability and salt rejection of carbon nanotube membranes and their application to water desalination

PubMed Central

Thomas, Michael; Corry, Ben

2016-01-01

Membranes made from nanomaterials such as nanotubes and graphene have been suggested to have a range of applications in water filtration and desalination, but determining their suitability for these purposes requires an accurate assessment of the properties of these novel materials. In this study, we use molecular dynamics simulations to determine the permeability and salt rejection capabilities for membranes incorporating carbon nanotubes (CNTs) at a range of pore sizes, pressures and concentrations. We include the influence of osmotic gradients and concentration build up and simulate at realistic pressures to improve the reliability of estimated membrane transport properties. We find that salt rejection is highly dependent on the applied hydrostatic pressure, meaning high rejection can be achieved with wider tubes than previously thought; while membrane permeability depends on salt concentration. The ideal size of the CNTs for desalination applications yielding high permeability and high salt rejection is found to be around 1.1 nm diameter. While there are limited energy gains to be achieved in using ultra-permeable CNT membranes in desalination by reverse osmosis, such membranes may allow for smaller plants to be built as is required when size or weight must be minimized. There are diminishing returns in further increasing membrane permeability, so efforts should focus on the fabrication of membranes containing narrow or functionalized CNTs that yield the desired rejection or selection properties rather than trying to optimize pore densities. PMID:26712639

Thermodynamic analysis of the interaction of partially hydrophobic cationic polyelectrolytes with sodium halide salts in water

NASA Astrophysics Data System (ADS)

Bončina, Matjaž; Lukšič, Miha; Seručnik, Mojca; Vlachy, Vojko

2014-05-01

Isothermal titration calorimetry was used to determine the temperature and concentration dependence of the enthalpy of mixing of 3,3- and 6,6-ionene fluorides, bromides, and iodides with low molecular weight salts (NaF, NaCl, NaBr, and NaI) in water. The magnitudes of the enthalpies, measured in the temperature range from 273 to 318 K, depended on the number of methylene groups on the ionene polyion (hydrophobicity), and on the anion of the added salt (ion-specificity). All enthalpies of mixing of 3,3- and 6,6-ionene fluorides with low molecular weight salts (NaCl, NaBr, and NaI) were negative, which is in contrast to the predictions of standard theories of polyelectrolyte solutions. This fact was interpreted in the light of the ion-water short-range interactions that are not accounted for in those theories. In contrast, the enthalpies of mixing of 3,3- and 6,6-ionene bromides and iodides with NaF were positive, being in accord with theory. Using the calorimetric data, we performed a model thermodynamic analysis of the polyelectrolyte-salt mixing process to obtain changes in the apparent standard Gibbs free energy, enthalpy, entropy, and heat capacity relative to the pure ionene fluorides in water. The results prove that halide ions replace fluoride counterions with a strength increasing in the order chloride < bromide < iodide. The process is enthalpy governed, accompanied by a positive change in the heat capacity.

Mesocarbon microbead based graphite for spherical fuel element to inhibit the infiltration of liquid fluoride salt in molten salt reactor

NASA Astrophysics Data System (ADS)

Zhong, Yajuan; Zhang, Junpeng; Lin, Jun; Xu, Liujun; Zhang, Feng; Xu, Hongxia; Chen, Yu; Jiang, Haitao; Li, Ziwei; Zhu, Zhiyong; Guo, Quangui

2017-07-01

Mesocarbon microbeads (MCMB) and quasi-isostatic pressing method were used to prepare MCMB based graphite (MG) for spherical fuel element to inhibit the infiltration of liquid fluoride salt in molten salt reactor (MSR). Characteristics of mercury infiltration and molten salt infiltration in MG were investigated and compared with A3-3 (graphite for spherical fuel element in high temperature gas cooled reactor) to identify the infiltration behaviors. The results indicated that MG had a low porosity about 14%, and an average pore diameter of 96 nm. Fluoride salt occupation of A3-3 (average pore diameter was 760 nm) was 10 wt% under 6.5 atm, whereas salt gain did not infiltrate in MG even up to 6.5 atm. It demonstrated that MG could inhibit the infiltration of liquid fluoride salt effectively. Coefficient of thermal expansion (CTE) of MG lies in 6.01 × 10-6 K-1 (α∥) and 6.15 × 10-6 K-1 (α⊥) at the temperature range of 25-700 °C. The anisotropy factor of MG calculated by CTE maintained below 1.02, which could meet the requirement of the spherical fuel element (below 1.30). The constant isotropic property of MG is beneficial for the integrity and safety of the graphite used in the spherical fuel element for a MSR.

Hypernatremia in Dice snakes (Natrix tessellata) from a coastal population: implications for osmoregulation in marine snake prototypes.

PubMed

Brischoux, François; Kornilev, Yurii V

2014-01-01

The widespread relationship between salt excreting structures (e.g., salt glands) and marine life strongly suggests that the ability to regulate salt balance has been crucial during the transition to marine life in tetrapods. Elevated natremia (plasma sodium) recorded in several marine snakes species suggests that the development of a tolerance toward hypernatremia, in addition to salt gland development, has been a critical feature in the evolution of marine snakes. However, data from intermediate stage (species lacking salt glands but occasionally using salty environments) are lacking to draw a comprehensive picture of the evolution of an euryhaline physiology in these organisms. In this study, we assessed natremia of free-ranging Dice snakes (Natrix tessellata, a predominantly fresh water natricine lacking salt glands) from a coastal population in Bulgaria. Our results show that coastal N. tessellata can display hypernatremia (up to 195.5 mmol x l(-1)) without any apparent effect on several physiological and behavioural traits (e.g., hematocrit, body condition, foraging). More generally, a review of natremia in species situated along a continuum of habitat use between fresh- and seawater shows that snake species display a concomitant tolerance toward hypernatremia, even in species lacking salt glands. Collectively, these data suggest that a physiological tolerance toward hypernatremia has been critical during the evolution of an euryhaline physiology, and may well have preceded the evolution of salt glands.

A model for the salt effect on adsorption equilibrium of basic protein to dye-ligand affinity adsorbent.

PubMed

Zhang, Songping; Sun, Yan

2004-01-01

A model describing the salt effect on adsorption equilibrium of a basic protein, lysozyme, to Cibacron Blue 3GA-modified Sepharose CL-6B (CB-Sepharose) has been developed. In this model, it is assumed that the presence of salt causes a fraction of dye-ligand molecules to lodge to the surface of the agarose gel, resulting from the induced strong hydrophobic interaction between dye ligand and agarose matrix. The salt effect on the lodging of dye-ligand is expressed by the equilibrium between salt and dye-ligand. For the interactions between protein and vacant binding sites, stoichiometric equations based either on cation exchanges or on hydrophobic interactions are proposed since the CB dye can be regarded as a cation exchanger contributed by the sulfonate groups on it. Combining with the basic concept of steric mass-action theory for ion exchange, which considers both the multipoint nature and the macromolecular steric shielding of protein adsorption, an explicit isotherm for protein adsorption equilibrium on the dye-ligand adsorbent is formulated, involving salt concentration as a variable. Analysis of the model parameters has yielded better understanding of the mechanism of salt effects on adsorption of the basic protein. Moreover, the model predictions are in good agreement with the experimental data over a wide range of salt and ligand concentrations, indicating the predictive nature of the model.

Hypernatremia in Dice Snakes (Natrix tessellata) from a Coastal Population: Implications for Osmoregulation in Marine Snake Prototypes

PubMed Central

Brischoux, François; Kornilev, Yurii V.

2014-01-01

The widespread relationship between salt excreting structures (e.g., salt glands) and marine life strongly suggests that the ability to regulate salt balance has been crucial during the transition to marine life in tetrapods. Elevated natremia (plasma sodium) recorded in several marine snakes species suggests that the development of a tolerance toward hypernatremia, in addition to salt gland development, has been a critical feature in the evolution of marine snakes. However, data from intermediate stage (species lacking salt glands but occasionally using salty environments) are lacking to draw a comprehensive picture of the evolution of an euryhaline physiology in these organisms. In this study, we assessed natremia of free-ranging Dice snakes (Natrix tessellata, a predominantly fresh water natricine lacking salt glands) from a coastal population in Bulgaria. Our results show that coastal N. tessellata can display hypernatremia (up to 195.5 mmol.l−1) without any apparent effect on several physiological and behavioural traits (e.g., hematocrit, body condition, foraging). More generally, a review of natremia in species situated along a continuum of habitat use between fresh- and seawater shows that snake species display a concomitant tolerance toward hypernatremia, even in species lacking salt glands. Collectively, these data suggest that a physiological tolerance toward hypernatremia has been critical during the evolution of an euryhaline physiology, and may well have preceded the evolution of salt glands. PMID:24658047

Effect of different salt adaptation strategies on the microbial diversity, activity, and settling of nitrifying sludge in sequencing batch reactors.

PubMed

Bassin, João Paulo; Kleerebezem, Robbert; Muyzer, Gerard; Rosado, Alexandre Soares; van Loosdrecht, Mark C M; Dezotti, Marcia

2012-02-01

The effect of salinity on the activity of nitrifying bacteria, floc characteristics, and microbial community structure accessed by fluorescent in situ hybridization and polymerase chain reaction-denaturing gradient gel electrophoresis techniques was investigated. Two sequencing batch reactors (SRB₁ and SBR₂) treating synthetic wastewater were subjected to increasing salt concentrations. In SBR₁, four salt concentrations (5, 10, 15, and 20 g NaCl/L) were tested, while in SBR₂, only two salt concentrations (10 and 20 g NaCl/L) were applied in a more shock-wise manner. The two different salt adaptation strategies caused different changes in microbial community structure, but did not change the nitrification performance, suggesting that regardless of the different nitrifying bacterial community present in the reactor, the nitrification process can be maintained stable within the salt range tested. Specific ammonium oxidation rates were more affected when salt increase was performed more rapidly and dropped 50% and 60% at 20 g NaCl/L for SBR₁ and SBR₂, respectively. A gradual increase in NaCl concentration had a positive effect on the settling properties (i.e., reduction of sludge volume index), although it caused a higher amount of suspended solids in the effluent. Higher organisms (e.g., protozoa, nematodes, and rotifers) as well as filamentous bacteria could not withstand the high salt concentrations.

Case report: Improvement in dissociative symptoms with mixed amphetamine salts.

PubMed

Scarella, Timothy M; Franzen, Jamie R

2017-01-01

Symptoms of dissociation, including dissociative amnesia, depersonalization, and derealization, commonly develop in individuals subject to chronic and repeated trauma during development. This includes the trauma of environmental inability to facilitate development of adequate cognitive strategies for coping with strong negative emotions. Dissociation likely involves dysregulated balance of prefrontal inhibition of limbic structures and inadequate regulation of attentional bias by both prefrontal and limbic systems. There is currently no established psychopharmacologic treatment for dissociative symptoms. Here the case of a woman with severe dissociative symptoms that were markedly improved with the administration of mixed amphetamine salts is discussed. Potential neurobiologic mechanisms for dissociative symptom improvement with psychostimulants are discussed.

Reduction of salt content of fish sauce by ethanol treatment.

PubMed

Liu, Yu; Xu, Ying; He, Xiaoxia; Wang, Dongfeng; Hu, Shiwei; Li, Shijie; Jiang, Wei

2017-08-01

Fish sauce is a traditional condiment in Southeast Asia, normally containing high concentration of salt. The solubility of salt is lower in ethanol than in water. In the present study, fish sauce was desalted by ethanol treatment (including the processes of ethanol addition, mixing, standing and rotary evaporation). The salt concentration of fish sauce decreased significantly from 29.72 to 19.72 g/100 mL when the treated ethanol concentration was 21% (v/v). The addition of more than 12% (v/v) of ethanol significantly reduced dry weight, total soluble nitrogen content and amino acids nitrogen content. Besides, the quality of fish sauce remained first grade if no more than 21% (v/v) of ethanol was used. Furthermore, sensory analyses showed that ethanol treatment significantly reduced the taste of salty and the odor of ammonia. This study demonstrates that ethanol treatment is a potential way to decrease salt content in fish sauce, which meanwhile limits the losses of nutritional and sensorial values within an acceptable range.

The asymmetric synthesis of terminal aziridines by methylene transfer from sulfonium ylides to imines.

PubMed

Kavanagh, Sarah A; Piccinini, Alessandro; Connon, Stephen J

2013-06-07

A new ylide-based protocol for the asymmetric aziridination of imines via methylene transfer has been developed involving the use of a simple chiral sulfonium salt and an organic strong base. A systematic study identified triisopropylphenyl sulfonylimines as optimal substrates for the process. Unexpectedly, hindered C2-symmetric sulfonyl salts incorporating bulky ethers at C-2 and C-5--which had previously been useful in the corresponding epoxidation chemistry--decomposed in these aziridination reactions via competing elimination pathways. Under optimised conditions it was found that a simple salt derived from (2R,5R)-2,5-diisopropyl thiolane could mediate asymmetric methylene transfer to a range of imines with uniformly excellent yields with 19-30% ee. Since this is a similar level of enantiomeric excess to that obtained using these same salts in epoxidation chemistry, it was concluded that if more bulky sulfonium salts could be devised which were resistant to decomposition under the reaction conditions, that highly enantioselective aziridine formation by methylene transfer would be possible.

Fast Pyrolysis of Poplar Using a Captive Sample Reactor: Effects of Inorganic Salts on Primary Pyrolysis Products

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mukarakate, C.; Robichaud, D.; Donohoe, B.

2012-01-01

We have constructed a captive sample reactor (CSR) to study fast pyrolysis of biomass. The reactor uses a stainless steel wire mesh to surround biomass materials with an isothermal environment by independent controlling of heating rates and pyrolysis temperatures. The vapors produced during pyrolysis are immediately entrained and transported in He carrier gas to a molecular beam mass spectrometer (MBMS). Formation of secondary products is minimized by rapidly quenching the sample support with liquid nitrogen. A range of alkali and alkaline earth metal (AAEM) and transition metal salts were tested to study their effect on composition of primary pyrolysis products.more » Multivariate curve resolution (MCR) analysis of the MBMS data shows that transition metal salts enhance pyrolysis of carbohydrates and AAEM salts enhances pyrolysis of lignin. This was supported by performing similar separate studies on cellulose, hemicellulose and extracted lignin. The effect of salts on char formation is also discussed.« less

Halococcus salifodinae sp. nov., an Archaeal Isolate from an Austrian Salt Mine

NASA Technical Reports Server (NTRS)

Denner, Ewald B. M.; McGenity, Terry J.; Busse, Hans-Jurgen; Grant, William D.; Wanner, Gerhard; Stan-Lotter, Helga

1994-01-01

A novel extremely halophilic archaeon (archaebacterium) was isolated from rock salt obtained from an Austrian salt mine. The deposition of the salt is thought to have occurred during the Permian period (225 x 106 to 280 x 10(exp 6) years ago). This organism grew over a pH range of 6.8 to 9.5. Electron microscopy revealed cocci in tetrads or larger clusters. The partial 16S rRNA sequences, polar lipid composition, and menaquinone content suggested that this organism was related to members of the genus Halococcus, while the whole-cell protein patterns, the presence of several unknown lipids, and the presence of pink pigmentation indicated that it was different from previously described coccoid halophiles. We propose that this isolate should be recognized as a new species and should be named Halococcus salifodinae. The type strain is Bl(sub p) (= ATCC 51437 = DSM 8989). A chemotaxonomically similar microorganism was isolated from a British salt mine.

Fast Proton Titration Scheme for Multiscale Modeling of Protein Solutions.

PubMed

Teixeira, Andre Azevedo Reis; Lund, Mikael; da Silva, Fernando Luís Barroso

2010-10-12

Proton exchange between titratable amino acid residues and the surrounding solution gives rise to exciting electric processes in proteins. We present a proton titration scheme for studying acid-base equilibria in Metropolis Monte Carlo simulations where salt is treated at the Debye-Hückel level. The method, rooted in the Kirkwood model of impenetrable spheres, is applied on the three milk proteins α-lactalbumin, β-lactoglobulin, and lactoferrin, for which we investigate the net-charge, molecular dipole moment, and charge capacitance. Over a wide range of pH and salt conditions, excellent agreement is found with more elaborate simulations where salt is explicitly included. The implicit salt scheme is orders of magnitude faster than the explicit analog and allows for transparent interpretation of physical mechanisms. It is shown how the method can be expanded to multiscale modeling of aqueous salt solutions of many biomolecules with nonstatic charge distributions. Important examples are protein-protein aggregation, protein-polyelectrolyte complexation, and protein-membrane association.

Heat-induced formation of myosin oligomer-soluble filament complex in high-salt solution.

PubMed

Shimada, Masato; Takai, Eisuke; Ejima, Daisuke; Arakawa, Tsutomu; Shiraki, Kentaro

2015-02-01

Heat-induced aggregation of myosin into an elastic gel plays an important role in the water-holding capacity and texture of meat products. Here, we investigated thermal aggregation of porcine myosin in high-salt solution over a wide temperature range by dynamic light scattering experiments. The myosin samples were readily dissolved in 1.0 M NaCl at 25 °C followed by dilution into various salt concentrations. The diluted solutions consistently contained both myosin monomers and soluble filaments. The filament size decreased with increasing salt concentration and temperature. High temperatures above Tm led to at least partial dissociation of soluble filaments and thermal unfolding, resulting in the formation of soluble oligomers and binding to the persistently present soluble filaments. Such a complex formation between the oligomers and filaments has never been observed. Our results provide new insight into the heat-induced myosin gelation in high-salt solution. Copyright © 2014 Elsevier B.V. All rights reserved.

NEUTRON RADIOGRAPHY MEASUREMENT OF SALT SOLUTION ABSORPTION IN MORTAR

PubMed Central

Lucero, Catherine L.; Spragg, Robert P.; Bentz, Dale P.; Hussey, Daniel S.; Jacobson, David L.; Weiss, W. Jason

2017-01-01

Some concrete pavements in the US have recently exhibited premature joint deterioration. It is hypothesized that one component of this damage can be attributed to a reaction that occurs when salt-laden water is absorbed in the concrete and reacts with the matrix. This study examines the absorption of CaCl2 solution in mortar via neutron imaging. Mortar specimens were prepared with water to cement ratios, (w/c), of 0.36, 0.42 and 0.50 by mass and exposed to chloride solutions with concentrations ranging from 0 % to 29.8 % by mass. Depth of fluid penetration and moisture content along the specimen length were determined for 96 h after exposure. At high salt concentration (29.8 %), the sorption rate decreased by over 80 % in all samples. Along with changes in surface tension and viscosity, CaCl2 reacts with the cement paste to produce products (Friedel’s salt, Kuzel’s salt, or calcium oxychloride) that block pores and reduce absorption. PMID:28626299

NEUTRON RADIOGRAPHY MEASUREMENT OF SALT SOLUTION ABSORPTION IN MORTAR.

PubMed

Lucero, Catherine L; Spragg, Robert P; Bentz, Dale P; Hussey, Daniel S; Jacobson, David L; Weiss, W Jason

2017-01-01

Some concrete pavements in the US have recently exhibited premature joint deterioration. It is hypothesized that one component of this damage can be attributed to a reaction that occurs when salt-laden water is absorbed in the concrete and reacts with the matrix. This study examines the absorption of CaCl 2 solution in mortar via neutron imaging. Mortar specimens were prepared with water to cement ratios, ( w/c ), of 0.36, 0.42 and 0.50 by mass and exposed to chloride solutions with concentrations ranging from 0 % to 29.8 % by mass. Depth of fluid penetration and moisture content along the specimen length were determined for 96 h after exposure. At high salt concentration (29.8 %), the sorption rate decreased by over 80 % in all samples. Along with changes in surface tension and viscosity, CaCl 2 reacts with the cement paste to produce products (Friedel's salt, Kuzel's salt, or calcium oxychloride) that block pores and reduce absorption.

The generation of thermal stress and strain during quenching

NASA Astrophysics Data System (ADS)

Soomro, A. B.

A viscoelastic-plastic mathematical model was used to calculate the thermal stress and strain generated during the quenching of an infinite plate of high hardenability steel (835M30) in water, oil and Polymer. In the present work the mathematical model was modified to include the effect of initial stress on the rate of stress relaxation, which has been found to be significant. The data required to incorporate this effect into the calculations, were obtained experimentally during the-.present investigation. The effect of an applied stress during transformation (transformation plasticity) was also introduced in the mathematical model. The new model produced a marked improvement in the degree of agreement between the calculated and experimental residual stress, although the corresponding level of agreement in the case of residual strain was less good. In particular, strains after water quenching agreed less well with experiment as a consequence of the change in the model, although this drawback was not found after oil and polymer quenching. The new mathematical model was used to investigate the effect of martempering, section size and transformation temperature range on the generation of thermal stress and strain. A salt bath treatment above the Ms temperature followed by air cooling prevented residual stress development, but an oil quench after the salt bath treatment generated a level of residual stress at the end of cooling that was similar to that obtained after a direct oil quench from 850°C. Neither martempering process was successful in reducing residual strain.With.an increase in section size a reduction in the residual stress and an increase in the distortions was obtained after a water quench. However, after oil quenching the overall effect of section size on residual stress and strain was small. The effect of variation in the transformation temperature range was found to be small in the case of residual stress but an increase in Ms temperature produced a significant increase in the level of residual strain.

Hexahedral Finite Element Mesh Capturing Realistic Geometries of Bayou Choctaw Strategic Petroleum Reserve

NASA Astrophysics Data System (ADS)

Park, B. Y.; Roberts, B. L.; Sobolik, S. R.

2016-12-01

The U.S. Strategic Petroleum Reserve (SPR) stores crude oil in 60 caverns located at four sites located along the Gulf Coast. As a matter of normal operation of caverns in a salt dome, the continuous mechanical creep of salt, along with the change in internal cavern and casing pressure due to cavern closure and fluid exchanges, impose several mechanical conditions on the skin, well, and casing of a cavern that could potentially create damage. Sandia, on behalf of DOE, is evaluating the structural integrity of the salt surrounding existing caverns in the Bayou Choctaw (BC) salt dome in Louisiana. In reality, the geometry, spacing, and depths of the caverns are irregular. It is not easy to realize the naturally and artificially formed cavern and salt dome for numerical analysis. It is harder to convert the geometries into the meshed mass consisting of only hexahedral finite elements. A three-dimensional (3D) finite element mesh capturing realistic geometries of the Bayou Choctaw site has been constructed using the seismic and sonar survey data obtained from the field (see Figures below). The mesh consists of hexahedral elements because the salt constitutive model is coded using hexahedral elements. Techniques to reduce the number of elements as much as possible to save on computer run time while maintaining computational accuracy are also developed. These methodologies could also be applied to construct computational meshes for the Big Hill, Bryan Mound, and West Hackberry SPR sites. The methodology could be applied to the complicated shape masses for not only various civil and geological structures but also biological applications such as artificial limbs. The newly developed mesh is expected to provide more accurate solutions of geotechnical concerns that arise due to the close proximity of the caverns to each other or to the edge of salt. Also, there are nine abandoned caverns, one of which is believed to be in a quasi-stable condition. Stability issues for these abandoned caverns must be evaluated and, if necessary, addressed to prevent potential cavern collapse. The integrity of wellbores at the interbed between the caprock and salt is another concern because oil leaks could occur due to the horizontal and downward movements of the salt top relative to the caprock.

Effect of Dihedral Angle and Porosity on Percolating-Sealing Capacity of Texturally Equilibrated Rock Salt

NASA Astrophysics Data System (ADS)

Ghanbarzadeh, S.; Hesse, M. A.; Prodanovic, M.; Gardner, J. E.

2013-12-01

Salt deposits in sedimentary basins have long been considered to be a seal against fluid penetration. However, experimental, theoretical and field evidence suggests brine (and oil) can wet salt crystal surfaces at higher pressures and temperatures, which can form a percolating network. This network may act as flow conduits even at low porosities. The aim of this work is to investigate the effects of dihedral angle and porosity on the formation of percolating paths in different salt network lattices. However, previous studies considered only simple homogeneous and isotropic geometries. This work extends the analysis to realistic salt textures by presenting a novel numerical method to describe the texturally equilibrated pore shapes in polycrystalline rock salt and brine systems. First, a theoretical interfacial topology was formulated to minimize the interfacial surface between brine and salt. Then, the resulting nonlinear system of ordinary differential equations was solved using the Newton-Raphson method. Results show that the formation of connected fluid channels is more probable in lower dihedral angles and at higher porosities. The connectivity of the pore network is hysteretic, because the connection and disconnection at the pore throats for processes with increasing or decreasing porosities occur at different porosities. In porous media with anisotropic solids, pores initially connect in the direction of the shorter crystal axis and only at much higher porosities in the other directions. Consequently, even an infinitesimal elongation of the crystal shape can give rise to very strong anisotropy in permeability of the pore network. Also, fluid flow was simulated in the resulting pore network to calculate permeability, capillary entry pressure and velocity field. This work enabled us to investigate the opening of pore space and sealing capacity of rock salts. The obtained pore geometries determine a wide range of petrophysical properties such as permeability and capillary entry pressure. This expanded knowledge of the salt textural behavior vs. depth could also improve drilling operations in salt. Second, a series of experiments in different P-T conditions was carried out to investigate the actual shape of equilibrated channels in salt. The synthetic salt samples were scanned at the High Resolution X-ray CT Facility at the Department of Geological Science, the University of Texas at Austin with resolution in 1-6 micron range. The experimental results show both equilibrated (tubular pores) and non-equilibrated (planar features) in salt structure. Image processing was carried out by two open source software programs: ImageJ, which is a public domain Java image processing program, and 3DMA-Rock, which is a software package for quantitative analyzing of the pore space in three-dimensional X-ray computed microtomographic images of rock. We obtain medial axis and medial surface of the pore space, as well as find and characterize the corresponding pore-throat network. We also report permeability of the pore space computed using Palabos software.

Biomass production in agroforestry and forestry systems on salt-affected soils in South Asia: exploration of the GHG balance and economic performance of three case studies.

PubMed

Wicke, Birka; Smeets, Edward M W; Akanda, Razzaque; Stille, Leon; Singh, Ranjay K; Awan, Abdul Rasul; Mahmood, Khalid; Faaij, Andre P C

2013-09-30

This study explores the greenhouse gas balance and the economic performance (i.e. net present value (NPV) and production costs) of agroforestry and forestry systems on salt-affected soils (biosaline (agro)forestry) based on three case studies in South Asia. The economic impact of trading carbon credits generated by biosaline (agro)forestry is also assessed as a potential additional source of income. The greenhouse gas balance shows carbon sequestration over the plantation lifetime of 24 Mg CO2-eq. ha(-1) in a rice-Eucalyptus camaldulensis agroforestry system on moderately saline soils in coastal Bangladesh (case study 1), 6 Mg CO2-eq. ha(-1) in the rice-wheat- Eucalyptus tereticornis agroforestry system on sodic/saline-sodic soils in Haryana state, India (case study 2), and 96 Mg CO2-eq. ha(-1) in the compact tree (Acacia nilotica) plantation on saline-sodic soils in Punjab province of Pakistan. The NPV at a discount rate of 10% is 1.1 k€ ha(-1) for case study 1, 4.8 k€ ha(-1) for case study 2, and 2.8 k€ ha(-1) for case study 3. Carbon sequestration translates into economic values that increase the NPV by 1-12% in case study 1, 0.1-1% in case study 2, and 2-24% in case study 3 depending on the carbon credit price (1-15 € Mg(-1) CO2-eq.). The analysis of the three cases indicates that the economic performance strongly depends on the type and severity of salt-affectedness (which affect the type and setup of the agroforestry system, the tree species and the biomass yield), markets for wood products, possibility of trading carbon credits, and discount rate. Copyright © 2013 Elsevier Ltd. All rights reserved.

Modeling Episodic Ephemeral Brine Lake Evaporation and Salt Crystallization on the Bonneville Salt Flats, Utah

NASA Astrophysics Data System (ADS)

Liu, T.; Harman, C. J.; Kipnis, E. L.; Bowen, B. B.

2017-12-01

Public concern about apparent reductions in the areal extent of the Bonneville Salt Flat (BSF) and perceived changes in inundation frequency has motivated renewed interest in the hydrologic and geochemical behavior of this salt playa. In this study, we develop a numerical modeling framework to simulate the relationship between hydrometeorologic variability, brine evaporation and salt crystallization processes on BSF. The BSF, locates in Utah, is the remnant of paleo-lake Bonneville, and is capped by up to 1 meter of salt deposition over a 100 km2 area. The BSF has two distinct hydrologic periods each year: a winter wet periods with standing surface brine and the summer dry periods when the brine is evaporated, exposing the surface salt crust. We develop a lumped non-linear dynamical models coupling conservation expressions from water, dissolved salt and thermal energy to investigate the seasonal and diurnal behavior of brine during the transition from standing brine to exposed salt at BSF. The lumped dynamic models capture important nonlinear and kinetic effects introduced by the high ionic concentration of the brine, including the pronounced effect of the depressed water activity coefficient on evaporation. The salt crystallization and dissolution rate is modeled as a kinetic process linearly proportional to the degree of supersaturation of brine. The model generates predictions of the brine temperature and the solute and solvent masses controlled by diurnal net radiation input and aerodynamic forcing. Two distinct mechanisms emerge as potential controls on salt production and dissolution: (1) evapo-concentration and (2) changes in solubility related to changes in brine temperature. Although the evaporation of water is responsible for ultimate disappearance of the brine each season ,variation in solubility is found to be the dominant control on diurnal cycles of salt precipitation and dissolution in the BSF case. Most salt is crystallized during nighttime, but the long-term salt production is driven by the seasonal evapo-concentration. Moreover, we find that the timing of the brine temperature fluctuations and salt production lags the diurnal net radiation input. The key controls on the magnitudes of these effects and phase lags are determined by analytical periodic analysis of linearized forms of the model.

Overexpression of a Chimeric Gene, OsDST-SRDX, Improved Salt Tolerance of Perennial Ryegrass

PubMed Central

Cen, Huifang; Ye, Wenxing; Liu, Yanrong; Li, Dayong; Wang, Kexin; Zhang, Wanjun

2016-01-01

The Drought and Salt Tolerance gene (DST) encodes a C2H2 zinc finger transcription factor, which negatively regulates salt tolerance in rice (Oryza sativa). Phylogenetic analysis of six homologues of DST genes in different plant species revealed that DST genes were conserved evolutionarily. Here, the rice DST gene was linked to an SRDX domain for gene expression repression based on the Chimeric REpressor gene-Silencing Technology (CRES-T) to make a chimeric gene (OsDST-SRDX) construct and introduced into perennial ryegrass by Agrobacterium-mediated transformation. Integration and expression of the OsDST-SRDX in transgenic plants were tested by PCR and RT-PCR, respectively. Transgenic lines overexpressing the OsDST-SRDX fusion gene showed obvious phenotypic differences and clear resistance to salt-shock and to continuous salt stresses compared to non-transgenic plants. Physiological analyses including relative leaf water content, electrolyte leakage, proline content, malondialdehyde (MDA) content, H2O2 content and sodium and potassium accumulation indicated that the OsDST-SRDX fusion gene enhanced salt tolerance in transgenic perennial ryegrass by altering a wide range of physiological responses. To our best knowledge this study is the first report of utilizing Chimeric Repressor gene-Silencing Technology (CRES-T) in turfgrass and forage species for salt-tolerance improvement. PMID:27251327

Small angle neutron scattering study of polyelectrolyte brushes grafted to well-defined gold nanoparticle interfaces.

PubMed

Jia, Haidong; Grillo, Isabelle; Titmuss, Simon

2010-05-18

Small angle neutron scattering (SANS) has been used to study the conformations, and response to added salt, of a polyelectrolyte layer grafted to the interfaces of well-defined gold nanoparticles. The polyelectrolyte layer is prepared at a constant coverage by grafting thiol-functionalized polystyrene (M(w) = 53k) to gold nanoparticles of well-defined interfacial curvature (R(c) = 26.5 nm) followed by a soft-sulfonation of 38% of the segments to sodium polystyrene sulfonate (NaPSS). The SANS profiles can be fit by Fermi-Dirac distributions that are consistent with a Gaussian distribution but are better described by a parabolic distribution plus an exponential tail, particularly in the high salt regime. These distributions are consistent with the predictions and measurements for osmotic and salted brushes at interfaces of low curvature. When the concentration of added salt exceeds the concentration of counterions inside the brush, there is a salt-induced deswelling, but even at the highest salt concentration the brush remains significantly swollen due to a short-ranged excluded volume interaction. This is responsible for the observed resistance to aggregation of these comparatively high concentration polyelectrolyte stabilized gold nanoparticle dispersions even in the presence of a high concentration of added salt.

Adhesion kinetics of viable Cryptosporidium parvum oocysts to quartz surfaces.

PubMed

Kuznar, Zachary A; Elimelech, Menachem

2004-12-15

The transport and deposition (adhesion) kinetics of viable Cryptosporidium parvum oocysts onto ultrapure quartz surfaces in a radial stagnation point flow system were investigated. Utilizing an optical microscope and an image-capturing device enabled real time observation of oocyst deposition behavior onto the quartz surface in solutions containing either monovalent (KCl) or divalent (CaCl2) salts. Results showed a significantly lower oocyst deposition rate in the presence of a monovalent salt compared to a divalent salt. With a monovalent salt, oocyst deposition rates and corresponding attachment efficiencies were relatively low, even at high KCl concentrations where Derjaguin-Landau-Verwey-Overbeek (DLVO) theory predicts the absence of an electrostatic energy barrier. On the other hand, in the presence of a divalent salt, oocyst deposition rates increased continuously as the salt concentration was increased over the entire range of ionic strengths investigated. The unusually low deposition rate in a monovalent salt solution is attributed to "electrosteric" repulsion between the Cryptosporidium oocyst and the quartz surface, most likely due to proteins on the oocyst surface that extend into the solution. It is further proposed that specific binding of calcium ions to the oocyst surface functional groups results in charge neutralization and conformational changes of surface proteins that significantly reduce electrosteric repulsion.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stormont, John; Lampe, Brandon; Mills, Melissa

The goal of this project is to improve the understanding of key aspects of the coupled thermal-mechanical-hydrologic response of granular (or crushed) salt used as a seal material for shafts, drifts, and boreholes in mined repositories in salt. The project is organized into three tasks to accomplish this goal: laboratory measurements of granular salt consolidation (Task 1), microstructural observations on consolidated samples (Task 2), and constitutive model development and evaluation (Task 3). Task 1 involves laboratory measurements of salt consolidation along with thermal properties and permeability measurements conducted under a range of temperatures and stresses expected for potential mined repositoriesmore » in salt. Testing focused on the role of moisture, temperature and stress state on the hydrologic (permeability) and thermal properties of consolidating granular salt at high fractional densities. Task 2 consists of microstructural observations made on samples after they have been consolidated to interpret deformation mechanisms and evaluate the ability of the constitutive model to predict operative mechanisms under different conditions. Task 3 concerns the development of the coupled thermal-mechanical-hydrologic constitutive model for granular salt consolidation. The measurements and observations in Tasks 1 and 2 were used to develop a thermal-mechanical constitutive model. Accomplishments and status from each of these efforts is reported in subsequent sections of this report« less

Conversion of alkali metal sulfate to the carbonate

DOEpatents

Sheth, A.C.

1979-10-01

A process is described for converting potassium sulfate to potassium carbonate in which a mixture of potassium sulfate and calcium oxide are reacted at a temperature in the range of between about 700/sup 0/C and about 800/sup 0/C with a gaseous mixture having a minor amount of hydrogen and/or carbon monoxide in a diluent with the calcium oxide being present in an amount not greater than about 20 percent by weight of the potassium sulfate to produce an aqueous mixture of potassium sulfide, potassium bisulfide, potassium hydroxide and calcium sulfide and a gaseous mixture of steam and hydrogen sulfide. The potassium and calcium salts are quenched to produce an aqueous slurry of soluble potassium salts and insoluble calcium salts and a gaseous mixture of steam and hydrogen sulfide. The insoluble calcium salts are then separated from the aqueous solution of soluble potassium salts. The calcium salts are dried to produce calcium sulfide, calcium bisulfide and steam, and then, the calcium sulfide and calcium bisulfide are converted to the oxide and recycled. The soluble potassium salts are carbonated to produce potassium carbonate which is concentrated and the precipitated crystals separated. the sulfur-containing compounds are further treated. This process was developed for desulfurization and reprocessing of spent seed from open-cycle coal-fired MHD generators for reuse.

Salt Lake City, Utah

NASA Technical Reports Server (NTRS)

2002-01-01

Salt Lake City, Utah, will host the 2002 Winter Olympic Games. The city is located on the southeastern shore of the Great Salt Lake and sits to the west of the Wasatch Mountains, which rise more than 3,500 meters (10,000 feet) above sea level. The city was first settled in 1847 by pioneers seeking relief from religious persecution. Today Salt Lake City, the capital of Utah, is home to more than 170,000 residents. This true-color image of Salt Lake City was acquired by the Enhanced Thematic Mapper Plus (ETM+), flying aboard Landsat 7, on May 26, 2000. The southeastern tip of the Great Salt Lake is visible in the upper left of the image. The furrowed green and brown landscape running north-south is a portion of the Wasatch Mountains, some of which are snow-capped (white pixels). The greyish pixels in the center of the image show the developed areas of the city. A number of water reservoirs can be seen east of the mountain range. Salt Lake City International Airport is visible on the northwestern edge of the city. About 20 miles south of the airport is the Bingham Canyon Copper Mine (tan pixels), the world's largest open pit excavation. See also this MODIS image of Utah. Image courtesy NASA Landsat7 Science Team and USGS Eros Data Center

"Abnormal" salt and solvent effects on anion/cation electron-transfer reactions: an interpretation based on Marcus-Hush treatment.

PubMed

Garcia-Fernandez, E; Prado-Gotor, R; Sanchez, F

2005-08-11

Salt and solvent effects on the kinetics of the reactions [Fe(CN)6]3- + [Ru(NH3)5pz](2+) right arrow over left arrow [Fe(CN)6]4- + [Ru(NH3)5pz]3+ (pz = pyrazine) have been studied through T-jump measurements. The forward and reverse reactions show different behaviors: "abnormal" salt and solvent effects in the first case and normal effects in the second one. These facts imply an asymmetric behavior of anion/cation reactions depending on the charge of the oxidant. The results can be rationalized by using the Marcus-Hush treatment for electron-transfer reactions.

Chemo-mechanics of salt damage in stone.

PubMed

Flatt, Robert J; Caruso, Francesco; Sanchez, Asel Maria Aguilar; Scherer, George W

2014-09-11

Many porous materials are damaged by pressure exerted by salt crystals growing in their pores. This is a serious issue in conservation science, geomorphology, geotechnical engineering and concrete materials science. In all cases, a central question is whether crystallization pressure will cause damage. Here we present an experiment in which the crystallization pressure and the pore saturation are varied in a controlled way. We demonstrate that a strain energy failure criterion can be used to predict when damage will occur. The experiment considered is the most widely used means to study the susceptibility to salt crystallization, so quantification of this test has far-reaching implications.

SENER molten salt tower technology. Ouarzazate NOOR III case

NASA Astrophysics Data System (ADS)

Relloso, Sergio; Gutiérrez, Yolanda

2017-06-01

NOOR III 150 MWe project is the evolution of Gemasolar (19.9 MWe) to large scale Molten Salt Tower plants. With more than 5 years of operational experience, Gemasolar lessons learned have been the starting point for the optimization of this technology, considered the leader of potential cost reduction in CSP. In addition, prototypes of plant key components (heliostat and receiver) were manufactured and thoroughly tested before project launch in order to prove the new engineering solutions adopted. The SENER proprietary technology of NOOR III will be applied in the next Molten Salt Tower plants that will follow in other countries, such as South Africa, Chile and Australia.

The solubility of the tetragonal form of hen egg white lysozyme from pH 4.0 to 5.4

NASA Technical Reports Server (NTRS)

Cacioppo, Elizabeth; Pusey, Marc L.

1991-01-01

Hen egg white lysozyme solubilities in the presence of the tetragonal crystal form have been determined. Conditions investigated cover the pH range 4.0 to 5.4, varying from 2.0 to 7.0 percent NaCl concentrations and from 4 to 25 C. In all instances, the solubilities were found to increase with temperature and decrease with increasing salt concentration. The effects of pH were more complex, showing a decreasing solubility with increasing pH at low salt concentration and an increasing solubility with increasing pH at high salt concentration.

Hot water, fresh beer, and salt

NASA Astrophysics Data System (ADS)

Crawford, Frank S.

1990-11-01

In the ``hot chocolate effect'' the best musical scales (those with the finest tone quality, largest range, and best tempo) are obtained by adding salt to a glass of hot water supersaturated with air. Good scales can also be obtained by adding salt to a glass of freshly opened beer (supersaturated with CO2) provided you first (a) get rid of much of the excess CO2 so as to produce smaller, hence slower, rising bubbles, and (b) get rid of the head of foam, which damps the standing wave and ruins the tone quality. Finally the old question, ``Do ionizing particles produce bubbles in fresh beer?'' is answered experimentally.

Interpretation of postmortem vitreous concentrations of sodium and chloride.

PubMed

Zilg, B; Alkass, K; Berg, S; Druid, H

2016-06-01

Vitreous fluid can be used to analyze sodium and chloride levels in deceased persons, but it remains unclear to what extent such results can be used to diagnose antemortem sodium or chloride imbalances. In this study we present vitreous sodium and chloride levels from more than 3000 cases. We show that vitreous sodium and chloride levels both decrease with approximately 2.2mmol/L per day after death. Since potassium is a well-established marker for postmortem interval (PMI) and easily can be analyzed along with sodium and chloride, we have correlated sodium and chloride levels with the potassium levels and present postmortem reference ranges relative the potassium levels. We found that virtually all cases outside the reference range show signs of antemortem hypo- or hypernatremia. Vitreous sodium or chloride levels can be the only means to diagnose cases of water or salt intoxication, beer potomania or dehydration. We further show that postmortem vitreous sodium and chloride strongly correlate and in practice can be used interchangeably if analysis of one of the ions fails. It has been suggested that vitreous sodium and chloride levels can be used to diagnose drowning or to distinguish saltwater from freshwater drowning. Our results show that in cases of freshwater drowning, vitreous sodium levels are decreased, but that this mainly is an effect of postmortem diffusion between the eye and surrounding water rather than due to the drowning process, since the decrease in sodium levels correlates with immersion time. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

Prediction in the Processing of Repair Disfluencies: Evidence from the Visual-World Paradigm

PubMed Central

Lowder, Matthew W.; Ferreira, Fernanda

2016-01-01

Two visual-world eye-tracking experiments investigated the role of prediction in the processing of repair disfluencies (e.g., The chef reached for some salt uh I mean some ketchup…). Experiment 1 showed that listeners were more likely to fixate a critical distractor item (e.g., pepper) during the processing of repair disfluencies compared to the processing of coordination structures (e.g., …some salt and also some ketchup…). Experiment 2 replicated the findings of Experiment 1 for disfluency versus coordination constructions and also showed that the pattern of fixations to the critical distractor for disfluency constructions was similar to the fixation patterns for sentences employing contrastive focus (e.g., …not some salt but rather some ketchup…). The results suggest that similar mechanisms underlie the processing of repair disfluencies and contrastive focus, with listeners generating sets of entities that stand in semantic contrast to the reparandum in the case of disfluencies or the negated entity in the case of contrastive focus. PMID:26866657

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hansen, Francis D.; Leigh, Christi; Stein, Walter

The 5th US/German Workshop on Salt Repository Research, Design, and Operation was held in Santa Fe New Mexico September 8-10, 2014. The forty seven registered participants were equally divided between the United States (US) and Germany, with one participant from The Netherlands. The agenda for the 2014 workshop was under development immediately upon finishing the 4th Workshop. Ongoing, fundamental topics such as thermomechanical behavior of salt, plugging and sealing, the safety case, and performance assessment continue to advance the basis for disposal of heat-generating nuclear waste in salt formations. The utility of a salt underground research laboratory (URL) remains anmore » intriguing concept engendering discussion of testing protocol. By far the most interest in this years’ workshop pertained to operational safety. Given events at the Waste Isolation Pilot Plant (WIPP), this discussion took on a new sense of relevance and urgency.« less

Characterizing the Weeks Island Salt Dome drilling of and seismic measurements from boreholes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sattler, A.R.; Harding, R.S.; Jacobson, R.D.

1996-10-01

A sinkhole 36 ft across, 30 ft deep was first observed in the alluvium over the Weeks Island Salt Dome (salt mine converted for oil storage by US Strategic Petroleum Reserve) May 1992. Four vertical, two slanted boreholes were drilled for diagnostics. Crosswell seismic data were generated; the velocity images suggest that the sinkhole collapse is complicated, not a simple vertical structure. The coring operation was moderately difficult; limited core was obtained through the alluvium, and the quality of the salt core from the first two vertical wells was poor. Core quality improved with better bit selection, mud, and drillingmore » method. The drilling fluid program provided fairly stable holes allowing open hole logs to be run. All holes were cemented successfully (although it took 3 attempts in one case).« less

Methanol synthesis using a catalyst combination of alkali or alkaline earth salts and reduced copper chromite

DOEpatents

Tierney, J.W.; Wender, I.; Palekar, V.M.

1995-01-24

The present invention relates to a novel route for the synthesis of methanol, and more specifically to the production of methanol by contacting synthesis gas under relatively mild conditions in a slurry phase with a catalyst combination comprising reduced copper chromite and basic alkali salts or alkaline earth salts. The present invention allows the synthesis of methanol to occur in the temperature range of approximately 100--160 C and the pressure range of 40--65 atm. The process produces methanol with up to 90% syngas conversion per pass and up to 95% methanol selectivity. The only major by-product is a small amount of easily separated methyl formate. Very small amounts of water, carbon dioxide and dimethyl ether are also produced. The present catalyst combination also is capable of tolerating fluctuations in the H[sub 2]/CO ratio without major deleterious effect on the reaction rate. Furthermore, carbon dioxide and water are also tolerated without substantial catalyst deactivation.

Active heat exchange system development for latent heat thermal energy storage

NASA Technical Reports Server (NTRS)

Lefrois, R. T.; Mathur, A. K.

1980-01-01

Five tasks to select, design, fabricate, test and evaluate candidate active heat exchanger modules for future applications to solar and conventional utility power plants were discussed. Alternative mechanizations of active heat exchange concepts were analyzed for use with heat of fusion phase change materials (PCMs) in the temperature range of 250 to 350 C. Twenty-six heat exchange concepts were reviewed, and eight were selected for detailed assessment. Two candidates were selected for small-scale experimentation: a coated tube and shell heat exchanger and a direct contact reflux boiler. A dilute eutectic mixture of sodium nitrate and sodium hydroxide was selected as the PCM from over 50 candidate inorganic salt mixtures. Based on a salt screening process, eight major component salts were selected initially for further evaluation. The most attractive major components in the temperature range of 250 to 350 C appeared to be NaNO3, NaNO2, and NaOH. Sketches of the two active heat exchange concepts selected for test are given.

Active heat exchange system development for latent heat thermal energy storage

NASA Astrophysics Data System (ADS)

Lefrois, R. T.; Mathur, A. K.

1980-04-01

Five tasks to select, design, fabricate, test and evaluate candidate active heat exchanger modules for future applications to solar and conventional utility power plants were discussed. Alternative mechanizations of active heat exchange concepts were analyzed for use with heat of fusion phase change materials (PCMs) in the temperature range of 250 to 350 C. Twenty-six heat exchange concepts were reviewed, and eight were selected for detailed assessment. Two candidates were selected for small-scale experimentation: a coated tube and shell heat exchanger and a direct contact reflux boiler. A dilute eutectic mixture of sodium nitrate and sodium hydroxide was selected as the PCM from over 50 candidate inorganic salt mixtures. Based on a salt screening process, eight major component salts were selected initially for further evaluation. The most attractive major components in the temperature range of 250 to 350 C appeared to be NaNO3, NaNO2, and NaOH. Sketches of the two active heat exchange concepts selected for test are given.

Tentative identification of volatile flavor compounds in commercial Budu, a Malaysian fish sauce, using GC-MS.

PubMed

Mohamed, Hajaratul Najwa; Man, Yaakob Che; Mustafa, Shuhaimi; Manap, Yazid Abdul

2012-05-03

Budu is a famous Malaysian fish sauce, usually used as seasoning and condiment in cooking. Budu is produced by mixing fish and salt at certain ratio followed by fermentation for six months in closed tanks. In this study, four commercial brands of Budu were analyzed for their chemical properties (pH, salt content and volatile compounds). The pH of Budu samples ranged from 4.50-4.92, while the salt (NaCl) content ranged between 11.80% and 22.50% (w/v). For tentative identification of volatile flavor compounds in Budu, two GC columns have been used, DB-WAX and HP-5MS. A total of 44 volatile compounds have been detected and 16 were common for both columns. 3-Methyl-1-butanol, 2-methylbutanal, 3-methylbutanal, dimethyl disulfide, 3-(methylthio)-propanal, 3-methylbutanoic acid and benzaldehye have been identified as the aroma-active compounds in Budu due to their lower threshold values.

Methanol synthesis using a catalyst combination of alkali or alkaline earth salts and reduced copper chromite

DOEpatents

Tierney, John W.; Wender, Irving; Palekar, Vishwesh M.

1995-01-01

The present invention relates to a novel route for the synthesis of methanol, and more specifically to the production of methanol by contacting synthesis gas under relatively mild conditions in a slurry phase with a catalyst combination comprising reduced copper chromite and basic alkali salts or alkaline earth salts. The present invention allows the synthesis of methanol to occur in the temperature range of approximately 100.degree.-160.degree. C. and the pressure range of 40-65 atm. The process produces methanol with up to 90% syngas conversion per pass and up to 95% methanol selectivity. The only major by-product is a small amount of easily separated methyl formate. Very small amounts of water, carbon dioxide and dimethyl ether are also produced. The present catalyst combination also is capable of tolerating fluctuations in the H.sub.2 /CO ratio without major deleterious effect on the reaction rate. Furthermore, carbon dioxide and water are also tolerated without substantial catalyst deactivation.

Methanol synthesis using a catalyst combination of alkali or alkaline earth salts and reduced copper chromite for methanol synthesis

DOEpatents

Tierney, John W.; Wender, Irving; Palekar, Vishwesh M.

1993-01-01

The present invention relates to a novel route for the synthesis of methanol, and more specifically to the production of methanol by contacting synthesis gas under relatively mild conditions in a slurry phase with a catalyst combination comprising reduced copper chromite and basic alkali salts or alkaline earth salts. The present invention allows the synthesis of methanol to occur in the temperature range of approximately 100.degree.-160.degree. C. and the pressure range of 40-65 atm. The process produces methanol with up to 90% syngas conversion per pass and up to 95% methanol selectivity. The only major by-product is a small amount of easily separated methyl formate. Very small amounts of water, carbon dioxide and dimethyl ether are also produced. The present catalyst combination also is capable of tolerating fluctuations in the H.sub.2 /CO ratio without major deleterious effect on the reaction rate. Furthermore, carbon dioxide and water are also tolerated without substantial catalyst deactivation.

Fluoride salts as phase change materials for thermal energy storage in the temperature range 1000-1400 K

NASA Technical Reports Server (NTRS)

Misra, Ajay K.

1988-01-01

Eutectic compositions and congruently melting intermediate compounds in binary and ternary fluoride salt systems were characterized for potential use as latent heat of fusion phase change materials to store thermal energy in the temperature range 1000-1400 K. The melting points and eutectic compositions for many systems with published phase diagrams were experimentally verified and new eutectic compositions having melting points between 1000 and 1400 K were identified. Heats of fusion of several binary and ternary eutectics and congruently melting compounds were experimentally measured by differential scanning calorimetry. For a few systems in which heats of mixing in the melts have been measured, heats of fusion of the eutectics were calculated from thermodynamic considerations and good agreement was obtained between the measured and calculated values. Several combinations of salts with high heats of fusion per unit mass (greater than 0.7 kJ/g) have been identified for possible use as phase change materials in advanced solar dynamic space power applications.

Reconstructive surgery for females with congenital adrenal hyperplasia due to 21-hydroxylase deficiency: a review from the Prince of Wales Hospital.

PubMed

Houben, C H; Tsui, S Y; Mou, J W; Chan, K W; Tam, Y H; Lee, K H

2014-12-01

To present the results of feminising genitoplasty done in female patients with congenital adrenal hyperplasia due to 21-hydroxylase deficiency. Case series. A tertiary referral centre in Hong Kong. Female patients with congenital adrenal hyperplasia undergoing corrective surgery for virilisation between 1993 and 2012. The operative result was judged with a scoring system (1-3) for four areas: appearance of clitoris, labia and vagina, plus requirement for revision surgery. A total of 23 female patients with congenital adrenal hyperplasia with a median age of 17.5 (range, 1.5-33.8) years were identified. Of these individuals, 17 presented in the neonatal period and early infancy, of which four had an additional salt-losing crisis. Six patients-including four migrants from mainland China-were late presenters at a median age of 2 (range, 0.5-14) years. Twenty-two patients had corrective surgery at a median age of 2 (range, 1-14) years. Clitoral reduction was performed in all, and further surgery in 21 patients. The additional surgery was flap vaginoplasty in 10 patients, a modified Passerini procedure in six, and a labial reconstruction in five; one patient with prominent clitoris was for observation only. Minor revision surgery (eg mucosal trimming) was required in three patients; a revision vaginoplasty was done in one individual. Of the 23 patients, 18 (78%) with a median age of 20 (range, 9.3-33.8) years participated in the outcome evaluation: a 'good' outcome (4 points) was seen in 12 patients and a 'satisfactory' (5-9 points) result in five patients. Nearly three quarters of our cohort (n=17) presented with classic virilising form of 21-hydroxylase deficiency. Only four (25%) patients experienced a salt-losing crisis. Female gender assignment at birth was maintained for all individuals in this group. 'Good' and 'satisfactory' outcomes of surgery were reported in nearly all participants.

Extraction, scrub, and strip test results for the salt waste processing facility caustic side solvent extraction solvent example

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peters, T. B.

An Extraction, Scrub, and Strip (ESS) test was performed on a sample of Salt Waste Processing Facility (SWPF) Caustic-Side Solvent Extraction (CSSX) solvent and salt simulant to determine cesium distribution ratios (D(Cs)), and cesium concentration in the strip effluent (SE) and decontaminated salt solution (DSS) streams; this data will be used by Parsons to help determine if the solvent is qualified for use at the SWPF. The ESS test showed acceptable performance of the solvent for extraction, scrub, and strip operations. The extraction D(Cs) measured 12.9, exceeding the required value of 8. This value is consistent with results from previousmore » ESS tests using similar solvent formulations. Similarly, scrub and strip cesium distribution ratios fell within acceptable ranges.« less

Salt flow direction and velocity during subsalt normal faulting and syn-kinematic sedimentation—implications from analytical calculations

NASA Astrophysics Data System (ADS)

Warsitzka, M.; Kukowski, N.; Kley, J.

2018-04-01

Salt flow induced by subsalt normal faulting is mainly controlled by tilting of the salt layer, the amount of differential loading due to syn-kinematic deposition, and tectonic shearing at the top or the base of the salt layer. Our study addresses the first two mechanisms and aims to examine salt flow patterns above a continuously moving subsalt normal fault and beneath a syn-kinematic minibasin. In such a setting, salt either tends to flow down towards the basin centre driven by its own weight or is squeezed up towards the footwall side owing to loading differences between the minibasin and the region above the footwall block. Applying isostatic balancing in analytical models, we calculated the steady-state flow velocity in a salt layer. This procedure gives insights into (1) the minimum vertical offset required for upward flow to occur, (2) the magnitude of the flow velocity, and (3) the average density of the supra-salt cover layer at the point at which upward flow starts. In a sensitivity study, we examined how the point of flow reversal and the velocity patterns are influenced by changes of the salt and cover layer thickness, the geometry of the cover flexure, the dip of the subsalt fault, compaction parameters of the supra-salt cover, the salt viscosity and the salt density. Our model results reveal that in most geological scenarios, salt flow above a continuously displacing subsalt normal fault goes through an early phase of downward flow. At sufficiently high fault offset in the range of 700-2600 m, salt is later squeezed upward towards the footwall side. This flow reversal occurs at smaller vertical fault displacement, if the thickness of the pre-kinematic layer is larger, the sedimentation rate of the syn-kinematic cover is higher, the compaction coefficient of cover sediments (i.e. the density increase with depth) is larger or the average density of the salt is lower. Other geometrical parameters such as the width of the cover monocline, the dip of the basement fault or the thickness of the salt layer have no significant influence on the point of reversal, but modify the velocity of the salt flow.

Two-year pilot study of newborn screening for congenital adrenal hyperplasia in New South Wales compared with nationwide case surveillance in Australia.

PubMed

Gleeson, Helena K; Wiley, Veronica; Wilcken, Bridget; Elliott, Elizabeth; Cowell, Christopher; Thonsett, Michael; Byrne, Geoffrey; Ambler, Geoffrey

2008-10-01

To assess the benefits and practicalities of setting up a newborn screening (NBS) program in Australia for congenital adrenal hyperplasia (CAH) through a 2 year pilot screening in ACT/NSW and comparing with case surveillance in other states. The pilot newborn screening occurred between 1/10/95 and 30/9/97 in NSW/ACT. Concurrently, case reporting for all new CAH cases occurred through the Australian Paediatric Surveillance Unit (APSU) across Australia. Details of clinical presentation, re-sampling and laboratory performance were assessed. 185,854 newborn infants were screened for CAH in NSW/ACT. Concurrently, 30 cases of CAH were reported to APSU, twelve of which were from NSW/ACT. CAH incidence was 1 in 15 488 (screened population) vs 1 in 18,034 births (unscreened) (difference not significant). Median age of initial notification was day 8 with confirmed diagnosis at 13(5-23) days in the screened population vs 16(7-37) days in the unscreened population (not significant). Of the 5 clinically unsuspected males in the screened population, one had mild salt-wasting by the time of notification, compared with salt-wasting crisis in all 6 males from the unscreened population. 96% of results were reported by day 10. Resampling was requested in 637 (0.4%) and median re-sampling delay was 11(0-28) days with higher resample rates in males (p < 0.0001). The within-laboratory cost per case of clinically unsuspected cases was A$42 717. There seems good justification for NBS for CAH based on clear prevention of salt-wasting crises and their potential long-term consequences. Also, prospects exist for enhancing screening performance.

Salt Stress Induced Variation in DNA Methylation Pattern and Its Influence on Gene Expression in Contrasting Rice Genotypes

PubMed Central

Karan, Ratna; DeLeon, Teresa; Biradar, Hanamareddy; Subudhi, Prasanta K.

2012-01-01

Background Salinity is a major environmental factor limiting productivity of crop plants including rice in which wide range of natural variability exists. Although recent evidences implicate epigenetic mechanisms for modulating the gene expression in plants under environmental stresses, epigenetic changes and their functional consequences under salinity stress in rice are underexplored. DNA methylation is one of the epigenetic mechanisms regulating gene expression in plant’s responses to environmental stresses. Better understanding of epigenetic regulation of plant growth and response to environmental stresses may create novel heritable variation for crop improvement. Methodology/Principal Findings Methylation sensitive amplification polymorphism (MSAP) technique was used to assess the effect of salt stress on extent and patterns of DNA methylation in four genotypes of rice differing in the degree of salinity tolerance. Overall, the amount of DNA methylation was more in shoot compared to root and the contribution of fully methylated loci was always more than hemi-methylated loci. Sequencing of ten randomly selected MSAP fragments indicated gene-body specific DNA methylation of retrotransposons, stress responsive genes, and chromatin modification genes, distributed on different rice chromosomes. Bisulphite sequencing and quantitative RT-PCR analysis of selected MSAP loci showed that cytosine methylation changes under salinity as well as gene expression varied with genotypes and tissue types irrespective of the level of salinity tolerance of rice genotypes. Conclusions/Significance The gene body methylation may have an important role in regulating gene expression in organ and genotype specific manner under salinity stress. Association between salt tolerance and methylation changes observed in some cases suggested that many methylation changes are not “directed”. The natural genetic variation for salt tolerance observed in rice germplasm may be independent of the extent and pattern of DNA methylation which may have been induced by abiotic stress followed by accumulation through the natural selection process. PMID:22761959

Role of adsorbed surfactant in the reaction of aryl diazonium salts with single-walled carbon nanotubes.

PubMed

Hilmer, Andrew J; McNicholas, Thomas P; Lin, Shangchao; Zhang, Jingqing; Wang, Qing Hua; Mendenhall, Jonathan D; Song, Changsik; Heller, Daniel A; Barone, Paul W; Blankschtein, Daniel; Strano, Michael S

2012-01-17

Because covalent chemistry can diminish the optical and electronic properties of single-walled carbon nanotubes (SWCNTs), there is significant interest in developing methods of controllably functionalizing the nanotube sidewall. To date, most attempts at obtaining such control have focused on reaction stoichiometry or strength of oxidative treatment. Here, we examine the role of surfactants in the chemical modification of single-walled carbon nanotubes with aryl diazonium salts. The adsorbed surfactant layer is shown to affect the diazonium derivatization of carbon nanotubes in several ways, including electrostatic attraction or repulsion, steric exclusion, and direct chemical modification of the diazonium reactant. Electrostatic effects are most pronounced in the cases of anionic sodium dodecyl sulfate and cationic cetyltrimethylammonium bromide, where differences in surfactant charge can significantly affect the ability of the diazonium ion to access the SWCNT surface. For bile salt surfactants, with the exception of sodium cholate, we find that the surfactant wraps tightly enough such that exclusion effects are dominant. Here, sodium taurocholate exhibits almost no reactivity under the explored reaction conditions, while for sodium deoxycholate and sodium taurodeoxycholate, we show that the greatest extent of reaction is observed among a small population of nanotube species, with diameters between 0.88 and 0.92 nm. The anomalous reaction of nanotubes in this diameter range seems to imply that the surfactant is less effective at coating these species, resulting in a reduced surface coverage on the nanotube. Contrary to the other bile salts studied, sodium cholate enables high selectivity toward metallic species and small band gap semiconductors, which is attributed to surfactant-diazonium coupling to form highly reactive diazoesters. Further, it is found that the rigidity of anionic surfactants can significantly influence the ability of the surfactant layer to stabilize the diazonium ion near the nanotube surface. Such Coulombic and surfactant packing effects offer promise toward employing surfactants to controllably functionalize carbon nanotubes. © 2011 American Chemical Society

The promotion of geomorphosites on salt from Sovata - Praid and Turda using cultural and scientific tourism

NASA Astrophysics Data System (ADS)

Toma, B.; Irimus, I.; Petrea, D.

2012-04-01

The paper highlights the role of geomorphosites on salt, in experts and specialists training, in geography of tourism and planning, namely, the involvement of educational factor in defining managerial and marketing skills of future specialists in training. Geographical area of investigation belongs to the Transylvanian tectonic basin, overlapped to saliferous tectonic area from eastern Transylvania, represented by Praid - Sovata - Corund anticline and Sic -Cojocna - Turda anticline, analysis is focused on the Praid - Sovata and Turda diapirs. Saliferous area Praid - Sovata - Corund is situated on the contact area of the Transylvanian Basin with neo-eruptiv mountain chain of Eastern Carpathians, Calimani - Gurghiu - Harghita, and at the contact of Târnavelor Plateau with the orogen alignment of Gurghiu - Harghita Mountains. The salt body, in the horizontal plane, has a quasi-circular shape, slightly ellipsoidal, with diameters of 1.2 and 1.4 km, and is estimated to have a burial depth of 2.6 to 2.8 km. The salt massif from Praid, pierce the Mio-Pliocene blanket around and appears at the surface as diapir, flanked by sedimentary rocks that are partially covered by extrusive post-Pliocene volcanic formations and Quaternary deposits. Evaporitic deposits presents a varied lithology represented by gypsum, anhydrite, salt rock, potassium salt and celestine. The salt massif from Turda develops on the anticline Sic -Cojocna - Turda, oriented NE - SW, 2 km NE of Turda's downtown. It has an elongated shape, about 4 km, with widths ranging from 700 m to 200 m and also with a thickness ranging from 750 m to over 1000 m. In terms of stratigraphy, the salt massif is surrounded by deposits belonging to Badenian, Sarmatian and Quaternary. Due to salt dissolution by meteoric waters, carsto-saline lakes were formed, and due to ceiling collapse, because of an intensive exploitation, and infiltrations of rainwater and rivers, antropo-salted lakes were formed. The water and mud of these lakes are used for external treatment. The holes resulting from exploitation were arranged and turned into treatment rooms for those affected by respiratory diseases. Localities Praid and Sovata from rural settlements, have become balneary resorts, that use these salt resources by multiple forms of tourism: spas, climatic, cultural, recreational and scientific. In Turda has developed both health, climacteric and recreational tourism, as well as cultural and historical tourism, given the historical relics that are housed here. The design of applicative segment of geomorphological sites on salt recovery, through tourism activities is the objective of our work. Methodological argumentation is supported by the objective motivation, of geomorphosites on salt capitalization, by the content of syllabus and specialization of geography of tourism and territorial planning, from the Faculty of Geography, Babes-Bolyai University from Cluj-Napoca. The syllabus content argues the need for knowledge of geomorphosites genesis, their morphology, touristic valences, urbanistic valences, and the possibility of recovery, through forms and types of tourism, namely, urban, agricultural, industrial forms and types of exploitation. Key words: salt, geomorphosites, Praid, Turda, recovery

Controlling chitosan-based encapsulation for protein and vaccine delivery

PubMed Central

Koppolu, Bhanu prasanth; Smith, Sean G.; Ravindranathan, Sruthi; Jayanthi, Srinivas; Kumar, Thallapuranam K.S.; Zaharoff, David A.

2014-01-01

Chitosan-based nano/microencapsulation is under increasing investigation for the delivery of drugs, biologics and vaccines. Despite widespread interest, the literature lacks a defined methodology to control chitosan particle size and drug/protein release kinetics. In this study, the effects of precipitation-coacervation formulation parameters on chitosan particle size, protein encapsulation efficiency and protein release were investigated. Chitosan particle sizes, which ranged from 300 nm to 3 μm, were influenced by chitosan concentration, chitosan molecular weight and addition rate of precipitant salt. The composition of precipitant salt played a significant role in particle formation with upper Hofmeister series salts containing strongly hydrated anions yielding particles with a low polydispersity index (PDI) while weaker anions resulted in aggregated particles with high PDIs. Sonication power had minimal effect on mean particle size, however, it significantly reduced polydispersity. Protein loading efficiencies in chitosan nano/microparticles, which ranged from 14.3% to 99.2%, was inversely related to the hydration strength of precipitant salts, protein molecular weight and directly related to the concentration and molecular weight of chitosan. Protein release rates increased with particle size and were generally inversely related to protein molecular weight. This study demonstrates that chitosan nano/microparticles with high protein loading efficiencies can be engineered with well-defined sizes and controllable release kinetics through manipulation of specific formulation parameters. PMID:24560459

Evaluating abiotic influences on soil salinity of inland managed wetlands and agricultural croplands in a semi-arid environment

USGS Publications Warehouse

Fowler, D.; King, Sammy L.; Weindorf, David C.

2014-01-01

Agriculture and moist-soil management are important management techniques used on wildlife refuges to provide adequate energy for migrant waterbirds. In semi-arid systems, the accumulation of soluble salts throughout the soil profile can limit total production of wetland plants and agronomic crops and thus jeopardize meeting waterbird energy needs. This study evaluates the effect of distinct hydrologic regimes associated with moist-soil management and agricultural production on salt accumulation in a semi-arid floodplain. We hypothesized that the frequency of flooding and quantity of floodwater in a moist-soil management hydroperiod results in a less saline soil profile compared to profiles under traditional agricultural management. Findings showed that agricultural croplands differed (p-value < 0.001, df = 9) in quantities of total soluble salts (TSS) compared to moist-soil impoundments and contained greater concentrations (TSS range = 1,160-1,750 (mg kg-1)) at depth greater than 55 cm below the surface of the profile, while moist-soil impoundments contained lower concentrations (TSS range = 307-531 (mg kg-1)) at the same depths. Increased salts in agricultural may be attributed to the lack of leaching afforded by smaller summer irrigations while larger periodic flooding events in winter and summer flood irrigations in moist-soil impoundments may serve as leaching events.

Effects of Detergent β-Octylglucoside and Phosphate Salt Solutions on Phase Behavior of Monoolein Mesophases

PubMed Central

Khvostichenko, Daria S.; Ng, Johnathan J.D.; Perry, Sarah L.; Menon, Monisha; Kenis, Paul J.A.

2013-01-01

Using small-angle x-ray scattering (SAXS), we investigated the phase behavior of mesophases of monoolein (MO) mixed with additives commonly used for the crystallization of membrane proteins from lipidic mesophases. In particular, we examined the effect of sodium and potassium phosphate salts and the detergent β-octylglucoside (βOG) over a wide range of compositions relevant for the crystallization of membrane proteins in lipidic mesophases. We studied two types of systems: 1), ternary mixtures of MO with salt solutions above the hydration boundary; and 2), quaternary mixtures of MO with βOG and salt solutions over a wide range of hydration conditions. All quaternary mixtures showed highly regular lyotropic phase behavior with the same sequence of phases (Lα, Ia3d, and Pn3m) as MO/water mixtures at similar temperatures. The effects of additives in quaternary systems agreed qualitatively with those found in ternary mixtures in which only one additive is present. However, quantitative differences in the effects of additives on the lattice parameters of fully hydrated mesophases were found between ternary and quaternary mixtures. We discuss the implications of these findings for mechanistic investigations of membrane protein crystallization in lipidic mesophases and for studies of the suitability of precipitants for mesophase-based crystallization methods. PMID:24138861

A new insight into the dependence of relaxation time on frequency in viscoelastic surfactant solutions: From experimental to modeling study.

PubMed

García, Brayan F; Saraji, Soheil

2018-05-01

The relaxation time in viscoelastic surfactant solutions is a function of temperature, salt/surfactant concentrations, resting conditions, as well as shear frequency. The simplistic assumption of a single and constant relaxation time is not representative of all relaxation modes in these solutions especially at high frequencies. Steady-state and oscillatory measurements are carried out to study the effects of high temperature, concentration and resting condition on the rheology of surfactants/salt mixtures including a non-ionic and a zwitterionic/anionic surfactant system. Furthermore, a novel semi-empirical rheological model is deducted based on Cates theory.This model introduces, for the first time, a frequency-dependence for the continuous relaxation time spectrum. At high temperatures, the non-ionic surfactant become more viscoelastic and the zwitterionic/anionic system loses its viscoelasticity. The addition of surfactant/salt improves the viscoelasticity of both systems, and, for the zwitterionic/anionic mixture, increasing the resting temperature improves its viscoelasticity. In addition, the proposed model significantly improves predictions of traditional Maxwell model for different viscoelastic surfactant solutions (using data from this study and the literature) for a considerable range of surfactant and salt combinations at a wide range of temperature. Copyright © 2018 Elsevier Inc. All rights reserved.

Organic ion association in aqueous phase and ab initio-based force fields: The case of carboxylate/ammonium salts

NASA Astrophysics Data System (ADS)

Houriez, Céline; Vallet, Valérie; Réal, Florent; Meot-Ner Mautner, Michael; Masella, Michel

2017-10-01

We performed molecular dynamics simulations of carboxylate/methylated ammonium ion pairs solvated in bulk water and of carboxylate/methylated ammonium salt solutions at ambient conditions using an ab initio-based polarizable force field whose parameters are assigned to reproduce only high end quantum computations, at the Møller-Plesset second-order perturbation theory/complete basis set limit level, regarding single ions and ion pairs as isolated and micro-hydrated in gas phase. Our results agree with the available experimental results regarding carboxylate/ammonium salt solutions. For instance, our force field approach predicts the percentage of acetate associated with ammonium ions in CH3 COO-/CH3 NH3+ solutions at the 0.2-0.8M concentration scale to range from 14% to 35%, in line with the estimates computed from the experimental ion association constant in liquid water. Moreover our simulations predict the number of water molecules released from the ion first hydration shell to the bulk upon ion association to be about 2.0 ± 0.6 molecules for acetate/protonated amine ion pairs, 3.1 ± 1.5 molecules for the HCOO-/NH4+ pair and 3.3 ± 1.2 molecules for the CH3COO-/(CH3)4N+ pair. For protonated amine-based ion pairs, these values are in line with experiment for alkali/halide pairs solvated in bulk water. All these results demonstrate the promising feature of ab initio-based force fields, i.e., their capacity in accurately modeling chemical systems that cannot be readily investigated using available experimental techniques.

Signature of Europa's Ocean Density on Gravity Data

NASA Astrophysics Data System (ADS)

Castillo, J. C.; Rambaux, N.

2015-12-01

Observations by the Galileo mission at Europa and Cassini-Huygens mission at Europa, Ganymede, Callisto, Enceladus, and Titan have found deep oceans at these objects with evidence for the presence of salts. Salt compounds are the products of aqueous alteration of the rock phase under hydrothermal conditions and have been predicted theoretically for these objects per analogy with carbonaceous chondrite parent bodies. Evidence for salt enrichment comes from magnetometer measurements (Galilean satellites), direct detection in the case of Enceladus, and inversion of the gravity data obtained at Titan. While there is direct detection for the presence of chlorides in icy grains ejected from Enceladus, the chemistry of the oceans detected so far, or even their densities, remain mostly unconstrained. However the increased ocean density impacts the interpretation of the tidal Love number k2and this may introduce confusion in the inference of the icy shell thickness from that parameter. We will present estimates of k2for a range of assumptions on Europa's hydrospheric structure that build on geophysical observations obtained by the Galileo mission combined with new models of Europa's interior. These models keep track of the compositions of the hydrated core and oceanic composition in a self-consistent manner. We will also estimate the electrical conductivity corresponding to the modeled oceanic composition. Finally we will explore how combining electromagnetic, topographic, and gravity data can decouple the signatures of the shell thickness and ocean composition on these geophysical observations. Acknowledgement: This work is being carried out at the Jet Propulsion Laboratory, California Institute of Technology, under contract to NASA. Government sponsorship acknowledged.

Gauging Flash-Floods: Automated Measurement of Flood Events in Mountain Torrents

NASA Astrophysics Data System (ADS)

Liechti, Katharina; Boss, Stefan; Fritschi, Bruno; Zappa, Massimiliano

2017-04-01

Rating curves contain uncertainties, especially in their upper range of higher discharge. This is due to more uncertainties in the measurements and also the typically lower number of measurements of high discharge events. However, it is the upper part of a rating curve that is of interest if it comes to dimensioning protection measures against floods and flash floods. For small municipalities who plan mitigation measures like a dam for protection against flash floods of small mountain torrent a rating curve as accurate as possible can be of great interest. It helps to reduce costs that can be caused by both under- and overdimensioning of a protective structure. We therefore invented a mobile discharge measurement station that is set up to construct a rating curve for small turbulent mountain torrents. It operates with salt dilution method and works in its current setup up to about 10 m3/s. The salt is injected automatically to the torrent when an event of desired magnitude takes place. Further downstream a conductivity measuring sensor records the change in salt concentration of the stream water. This mechanism is guided by automatic continuous observation of radar quantitative precipitation estimates (QPE) and a water pressure sensor. Measurements at a first test site gave promising results. The system does event measurements independent of the time of day and day of the week. The measuring equipment at the field site is only activated in case of an event. Therefore it has a low power consumption and can be run by only two solar panels.

A novel ultra high-performance liquid chromatography-tandem mass spectrometry method for the simultaneous determination of xanthones and steroidal saponins in crude and salt-processed Anemarrhenae Rhizoma aqueous extracts.

PubMed

Ji, De; Su, Xiaonan; Huang, Ziyan; Wang, Qiaohan; Lu, Tulin

2018-06-01

We established a rapid and sensitive ultra high-performance liquid chromatography tandem mass spectrometry method for the simultaneous quantification of xanthones and steroidal saponins in rat plasma. Chromatographic separation was achieved on a C 18 column with a mobile phase comprising acetonitrile and 0.1% formic acid. The detection was performed by negative electrospray ionization in multiple reaction monitoring mode. The validated method showed good linearity within the tested range (r > 0.9945). The intra- and interday precision at high, medium, and low concentrations was less than 7.96%. The bias of accuracies ranged from -1.92 to 9.62%. The extraction recoveries of the compounds ranged from 84.78 to 88.69%, and the matrix effects ranged from 96.76 to 108.59%. This method was successfully applied to a pharmacokinetic comparison of crude and salt-processed Anemarrhenae Rhizoma aqueous extracts after oral administration in rats. The maximum plasma concentration and area under concentration-time curve of timosaponin BIII and timosaponin AIII increased significantly (P < 0.05 or 0.01) and those of timosaponin BII decreased significantly (P < 0.05) after processing. These results could contribute to the clinical application of crude and salt-processed Anemarrhenae Rhizoma and reveal the processing mechanism. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Structural characteristics of alkaline phosphatase from the moderately halophilic bacterium Halomonas sp. 593

PubMed Central

Arai, Shigeki; Yonezawa, Yasushi; Ishibashi, Matsujiro; Matsumoto, Fumiko; Adachi, Motoyasu; Tamada, Taro; Tokunaga, Hiroko; Blaber, Michael; Tokunaga, Masao; Kuroki, Ryota

2014-01-01

Alkaline phosphatase (AP) from the moderate halophilic bacterium Halomonas sp. 593 (HaAP) catalyzes the hydrolysis of phosphomonoesters over a wide salt-concentration range (1–4 M NaCl). In order to clarify the structural basis of its halophilic characteristics and its wide-range adaptation to salt concentration, the tertiary structure of HaAP was determined by X-ray crystallography to 2.1 Å resolution. The unit cell of HaAP contained one dimer unit corresponding to the biological unit. The monomer structure of HaAP contains a domain comprised of an 11-stranded β-sheet core with 19 surrounding α-helices similar to those of APs from other species, and a unique ‘crown’ domain containing an extended ‘arm’ structure that participates in formation of a hydrophobic cluster at the entrance to the substrate-binding site. The HaAP structure also displays a unique distribution of negatively charged residues and hydrophobic residues in comparison to other known AP structures. AP from Vibrio sp. G15-21 (VAP; a slight halophile) has the highest similarity in sequence (70.0% identity) and structure (Cα r.m.s.d. of 0.82 Å for the monomer) to HaAP. The surface of the HaAP dimer is substantially more acidic than that of the VAP dimer (144 exposed Asp/Glu residues versus 114, respectively), and thus may enable the solubility of HaAP under high-salt conditions. Conversely, the monomer unit of HaAP formed a substantially larger hydrophobic interior comprising 329 C atoms from completely buried residues, whereas that of VAP comprised 264 C atoms, which may maintain the stability of HaAP under low-salt conditions. These characteristics of HaAP may be responsible for its unique functional adaptation permitting activity over a wide range of salt concentrations. PMID:24598750

Local annual survival and seasonal residency rates of Semipalmated Sandpipers (Calidris pusilla) in Puerto Rico

USGS Publications Warehouse

Rice, S.M.; Collazo, J.A.; Alldredge, M.W.; Harrington, B.A.; Lewis, A.R.

2007-01-01

We report seasonal residency and local annual survival rates of migratory Semipalmated Sandpipers (Calidris pusilla) at the Cabo Rojo salt flats, Puerto Rico. Residency rate (daily probability of remaining on the flats) was 0.991 ± 0.001 (x̄ ± SE), yielding a mean length of stay of 110 days. This finding supports the inclusion of the Caribbean as part of the species' winter range. Average estimated percentage of fat was low but increased throughout the season, which suggests that birds replenish some spent fat reserves and strive for energetic maintenance. Local annual survival rate was 0.62 ± 0.04, within the range of values reported for breeding populations at Manitoba and Alaska (0.53–0.76). The similarity was not unexpected because estimates were obtained annually but at opposite sites of their annual migratory movements. Birds captured at the salt flats appeared to be a mix of birds from various parts of the breeding range, judging from morphology (culmen's coefficient of variation = 9.1, n = 106). This suggested that origin (breeding area) of birds and their proportion in the data should be ascertained and accounted for in analyses to glean the full conservation implications of winter-based annual survival estimates. Those data are needed to unravel the possibility that individuals of distinct populations are affected by differential mortality factors across different migratory routes. Mean length of stay strongly suggested that habitat quality at the salt flats was high. Rainfall and tidal flow combine to increase food availability during fall. The salt flats dry up gradually toward late January, at the onset of the dry season. Semipalmated Sandpipers may move west to other Greater Antilles or south to sites such as coastal Surinam until the onset of spring migration. They are not an oversummering species at the salt flats. Conservation efforts in the Caribbean region require understanding the dynamics of this species throughout winter to protect essential habitat.

Salt Weathering on Mars

NASA Astrophysics Data System (ADS)

Jagoutz, E.

2006-12-01

Large well rounded boulders and angular rock fragments characterizes the Martian landscape as seen on the recent excellent quality photos. Analyzing the different rock-shapes indicates a time sequence of emplacement, fragmentation and transport of different rocks on Mars, which might give interesting insight into transport and weathering processes. Larger commonly well rounded boulders were emplaced onto gravel plains. After emplacement, these rocks were fragmented and disassembled. Nests of angular rock fragments are marking the locations of preexisting larger rocks. Frequently it is possible to reconstruct larger rounded rocks from smaller angular fragments. In other cases transport after fragmentation obscured the relationship of the fragments. However, a strewn field of fragments is still reminiscent of the preexisting rock. Mechanical salt weathering could be a plausible explanation for the insitu fragmentation of larger rounded blocks into angular fragments. Impact or secondary air fall induced fragmentation produces very different patterns, as observed around impact crates on Earth. Salt weathering of rocks is a common process in terrestrial environments. Salt crystallization in capillaries causes fragmentation of rocks, irrespective of the process of salt transportation and concentration. On Earth significant salt weathering can be observed in different climatic environments: in the transition zone of alluvial aprons and salt playas in desserts and in dry valleys of Antarctica. In terrestrial semi-arid areas the salt is transported by salt solution, which is progressively concentrated by evaporation. In Antarctic dry valleys freeze-thaw cycles causes salt transportation and crystallization resulting in rock fragmentation. This salt induced process can lead to complete destruction of rocks and converts rocks to fine sand. The efficient breakdown of rocks is dominating the landscape in some dry valleys of the Earth but possibly also on Mars. (Malin, 1974). However, irrespectively of the climatic environment a liquid brine is a necessity for salt induced fragmentation of rocks.M. C. Malin (1974) JGR Vol 79,26 p 3888-3894

The origin of brines and salts in Chilean salars: a hydrochemical review

NASA Astrophysics Data System (ADS)

Risacher, François; Alonso, Hugo; Salazar, Carlos

2003-11-01

Northern Chile is characterized by a succession of north-south-trending ranges and basins occupied by numerous saline lakes and salt crusts, collectively called salars. Fossil salt crusts are found to the west in the extremely arid Central Valley, while active salars receiving permanent inflows fill many intravolcanic basins to the east in the semiarid Cordillera. Sea salts and desert dust are blown eastward over the Cordillera, where they constitute an appreciable fraction of the solute load of very dilute waters (salt content<0.1 g/l). The weathering of volcanic rocks contributes most components to inflow waters with salt content ranging from 0.1 to 0.6 g/l. However, the average salt content of all inflows is much higher: about 3.2 g/l. Chemical composition, Cl/Br ratio, and 18O- 2H isotope contents point to the mixing of very dilute meteoric waters with present lake brines for the origin of saline inflows. Ancient gypsum in deep sedimentary formations seems to be the only evaporitic mineral recycled in present salars. Saline lakes and subsurface brines are under steady-state regime. The average residence time of conservative components ranges from a few years to some thousands years, which indicates a permanent leakage of the brines through bottom sediments. The infiltrating brines are recycled in the hydrologic system where they mix with dilute meteoric waters. High heat flow is the likely driving force that moves the deep waters in this magmatic arc region. Active Chilean salars cannot be considered as terminal lakes nor, strictly speaking, as closed basin lakes. Almost all incoming salts leave the basin and are transported elsewhere. Moreover, the dissolution of fossil salt crusts in some active salars also carries away important fluxes of components in percolating brines. Evaporative concentration of inflow waters leads to sulfate-rich or calcium-rich, near-neutral brines. Alkaline brines are almost completely lacking. The alkalinity/calcium ratio of inflow waters is lowered by the oxidation of native sulfur (reducing alkalinity) and the deposition of eolian gypsum (increasing Ca concentration). Theoretically, SO 4-rich inflow waters and their derived SO 4-rich brines should be found in the intravolcanic basins of the Cordillera because of the ubiquity of native sulfur, while Ca-rich brines should prevail in sedimentary basins where Ca-rich minerals are abundant. This relation is perfectly observed in the salar de Atacama, the largest in Chile. However, several salars located within the volcanic Cordillera belong to the Ca-rich group. Inflows and brines may have acquired their Ca-rich composition in Pleistocene time when their drainage basins were mainly sedimentary. Later on, recent lava flows and ignimbrites covered the sedimentary formations. Underground waters may have kept their early sedimentary signature by continuous recycling. However, the weathering of volcanic rocks tend to slowly shift the water compositions from the Ca-rich to the SO 4-rich type.

Numerical Modeling of ROM Panel Closures at WIPP

NASA Astrophysics Data System (ADS)

Herrick, C. G.

2016-12-01

The Waste Isolation Pilot Plant (WIPP) in New Mexico is a U.S. DOE geologic repository for permanent disposal of defense-related transuranic (TRU) waste. Waste is emplaced in panels excavated in a bedded salt formation (Salado Fm.) at 655 m bgs. In 2014 the U.S. EPA approved the new Run-of-Mine Panel Closure System (ROMPCS) for WIPP. The closure system consists of 100 feet of run-of-mine (ROM) salt sandwiched between two barriers. Nuclear Waste Partnership LLC (the M&O contractor for WIPP) initiated construction of the ROMPCS. The design calls for three horizontal ROM salt layers at different compaction levels ranging from 70-85% intact salt density. Due to panel drift size constraints and equipment availability the design was modified. Three prototype panel closures were constructed: two having two layers of compacted ROM salt (one closure had 1% water added) and a third consisting of simply ROM salt with no layering or added water. Sampling of the prototype ROMPCS layers was conducted to determine the following ROM salt parameters: thickness, moisture content, emplaced density, and grain-size distribution. Previous modeling efforts were performed without knowledge of these ROM salt parameters. This modeling effort incorporates them. The program-accepted multimechanism deformation model is used to model intact salt room creep closure. An advanced crushed salt model is used to model the ROM salt. Comparison of the two models' results with the prototypes' behavior is given. Our goal is to develop a realistic, reliable model that can be used for ROM salt applications at WIPP. Sandia National Laboratories is a multi-program laboratory operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the U. S. Department of Energy's National Nuclear Security Administration under contract DE-AC04-94AL85000. This research is funded by WIPP programs administered by the Office of Environmental Management (EM) of the U.S Department of Energy SAND2016-7259A

Transmutation Scoping Studies for a Chloride Molten Salt Reactor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Heidet, Florent; Feng, Bo; Kim, Taek

2016-01-01

Over the past few years, there has been strong renewed interest from private industry, mostly from start-up enterprises, in molten salt reactor (MSR) technologies because of the unique properties of this class of reactors. These are reactors in which the fuel is homogeneously mixed with the coolant in the form of liquid salts and is circulated continuously into and out of the active core region with on-line fuel management, salt treatment, and salt processing. In response to such wide-spread interest, Argonne National Laboratory is expanding its well-established reactor modelling and simulation expertise and infrastructure to enable detailed analysis and designmore » of MSRs. The tools being developed are able to simulate the continuous fuel flow, the complex on-line fuel management and elemental removal processes (e.g., fission product removal) using depletion steps representative of a real MSR system. Leveraging these capabilities, a parametric study on the transmutation performance of a simplified actinide-burning MSR concept that uses a chloride-based salt was performed. This type of salt has attracted attention over the more commonly discussed fluoride-based salts since no tritium is produced as a result of irradiation and it is compatible with a fast neutron spectrum. The studies discussed in this paper examine the performance of a burner MSR design with a fixed core size and power density over a range of possible fuel salt molar ratios with NaCl-MgCl2 as the carrier salt. The intent is to quantify the impact on the required transuranics content of the make-up fuel, the actinide transmutation rates, and other performance characteristics for typical burner MSR designs.« less

Agreement between twenty-four hour salt ingestion and sodium excretion in a controlled environment

PubMed Central

Lerchl, Kathrin; Rakova, Natalia; Dahlmann, Anke; Rauh, Manfred; Goller, Ulrike; Basner, Mathias; Dinges, David F.; Beck, Luis; Agureev, Alexander; Larina, Irina; Baranov, Victor; Morukov, Boris; Eckardt, Kai-Uwe; Vassilieva, Galina; Wabel, Peter; Vienken, Jörg; Kirsch, Karl; Johannes, Bernd; Krannich, Alexander; Luft, Friedrich C.; Titze, Jens

2015-01-01

Accurately collected 24-hour urine collections are presumed to be valid for estimating salt intake in individuals. We performed two independent ultra-long-term salt balance studies lasting 105 (4 men) and 205 (6 men) days in 10 men simulating a flight to Mars. We controlled dietary intake of all constituents for months at salt intakes of 12, 9, and 6 grams per day and collected all urine. The subjects’ daily menus consisted of 27,279 individual servings, out of which 83.0% were completely consumed, 16.5% completely rejected, and 0.5% incompletely consumed. Urinary recovery of dietary salt was 92% of recorded intake, indicating long-term steady state sodium balance in both studies. Even at fixed salt intake, 24-hour sodium excretion (UNaV) showed infradian rhythmicity. We defined a ±25 mmol deviation from the average difference between recorded sodium intake and UNaV as the prediction interval to accurately classify a 3-gram difference in salt intake. Due to the biological variability in UNaV, only every-other daily urine sample correctly classified a 3-gram difference in salt intake (49%). By increasing the observations to three consecutive 24-hour collections and sodium intakes, classification accuracy improved to 75%. Collecting seven 24-hour urines and sodium intake samples improved classification accuracy to 92%. We conclude that single 24-hour urine collections at intakes ranging from 6–12 grams salt per day were not suitable to detect a 3-gram difference in individual salt intake. Repeated measurements of 24-hour UNaV improve precision. This knowledge could be relevant to patient care and the conduct of intervention trials. PMID:26259596

Agreement between 24-hour salt ingestion and sodium excretion in a controlled environment.

PubMed

Lerchl, Kathrin; Rakova, Natalia; Dahlmann, Anke; Rauh, Manfred; Goller, Ulrike; Basner, Mathias; Dinges, David F; Beck, Luis; Agureev, Alexander; Larina, Irina; Baranov, Victor; Morukov, Boris; Eckardt, Kai-Uwe; Vassilieva, Galina; Wabel, Peter; Vienken, Jörg; Kirsch, Karl; Johannes, Bernd; Krannich, Alexander; Luft, Friedrich C; Titze, Jens

2015-10-01

Accurately collected 24-hour urine collections are presumed to be valid for estimating salt intake in individuals. We performed 2 independent ultralong-term salt balance studies lasting 105 (4 men) and 205 (6 men) days in 10 men simulating a flight to Mars. We controlled dietary intake of all constituents for months at salt intakes of 12, 9, and 6 g/d and collected all urine. The subjects' daily menus consisted of 27 279 individual servings, of which 83.0% were completely consumed, 16.5% completely rejected, and 0.5% incompletely consumed. Urinary recovery of dietary salt was 92% of recorded intake, indicating long-term steady-state sodium balance in both studies. Even at fixed salt intake, 24-hour urine collection for sodium excretion (UNaV) showed infradian rhythmicity. We defined a ±25 mmol deviation from the average difference between recorded sodium intake and UNaV as the prediction interval to accurately classify a 3-g difference in salt intake. Because of the biological variability in UNaV, only every other daily urine sample correctly classified a 3-g difference in salt intake (49%). By increasing the observations to 3 consecutive 24-hour collections and sodium intakes, classification accuracy improved to 75%. Collecting seven 24-hour urines and sodium intake samples improved classification accuracy to 92%. We conclude that single 24-hour urine collections at intakes ranging from 6 to 12 g salt per day were not suitable to detect a 3-g difference in individual salt intake. Repeated measurements of 24-hour UNaV improve precision. This knowledge could be relevant to patient care and the conduct of intervention trials. © 2015 American Heart Association, Inc.

Iodine status in pregnancy and household salt iodine content in rural Bangladesh.

PubMed

Shamim, Abu Ahmed; Christian, Parul; Schulze, Kerry J; Ali, Hasmot; Kabir, Alamgir; Rashid, Mahbubur; Labrique, Alain; Salamatullah, Qauzi; West, Keith P

2012-04-01

Adequate maternal iodine intake is essential during pregnancy for the development of the foetus. To assess the extent of iodine insufficiency and its association with household iodized salt in rural Bangladesh, we measured urinary iodine and household salt iodine content among pregnant women in early (≤16 weeks, n = 1376) and late (≥32 weeks, n = 1114) pregnancy. Salt (∼20 g) and a spot urine sample (∼10 mL) were collected from women participating in a randomized, placebo-controlled trial of vitamin A or beta-carotene supplementation in rural northwestern Bangladesh during home visits in early and late pregnancy. Salt iodine was analyzed by iodometric titration, and urinary iodine by the Ohashi method. Almost all salt samples had some detectable iodine, but over 75% contained <15 ppm. Median (interquartile range) urinary iodine concentrations were 66 (34-133) and 55 (28-110) µg L⁻¹ in early and late pregnancy, respectively; urinary iodine <150 µg L⁻¹ was found in ∼80% of women at both times in pregnancy. Although the risk of iodine insufficiency declined with increasing iodine content of household salt (P for trend <0.05), median urinary iodine did not reach 150 µg L⁻¹ until iodine in household salt was at least 32 ppm and 51 ppm during early and late pregnancy, respectively. Despite a national policy on universal salt iodization, salt iodine content remains insufficient to maintain adequate maternal iodine status throughout pregnancy in rural northern Bangladesh. Alternative measures like direct iodine supplementation during pregnancy could be considered to assure adequate iodine status during this high-risk period of life. © 2010 Blackwell Publishing Ltd.

Fluoride metabolism when added to salt.

PubMed

Whitford, Gary M

2005-01-01

The purpose of this review is to present the general characteristics of the metabolism of fluoride particularly as it occurs when ingested with fluoridated salt. Following the absorption of salt-borne fluoride from the stomach and intestines, its metabolism is identical to that of water-borne fluoride or other vehicles containing ionized fluoride. Because fluoridated salt is almost always ingested with food, however, absorption from the gastrointestinal tract may be delayed or reduced. Reports dealing with this subject have shown that fluoride absorption is delayed and, therefore, peak plasma concentrations are lower than when fluoride is ingested with water. The amount of ingested fluoride that is finally absorbed, however, is not appreciably affected unless the meal is composed mainly of components with high calcium concentrations. In this case, the extent of absorption can be reduced by as much as 50%. Fluoridated salt is also ingested less frequently than fluoridated water. Data are presented to show that the dose size and frequency of ingestion have only minor effects on fluoride retention in the body and on the concentrations in plasma, bone and enamel. Finally, calculations are presented to show that the risk of acute toxicity from fluoridated salt is virtually non-existent.

Alkali and alkaline earth metal salts of tetrazolone: structurally interesting and excellently thermostable.

PubMed

He, Piao; Wu, Le; Wu, Jin-Ting; Yin, Xin; Gozin, Michael; Zhang, Jian-Guo

2017-07-04

Tetrazolone (5-oxotetrazole) was synthesized by a moderate strategy through three steps (addition, cyclization and catalytic hydrogenation) avoiding the unstable intermediate diazonium, as reported during the previous preparation. Alkali and alkaline earth metal salts with lithium (1), sodium (2), potassium (3), rubidium (4) caesium (5), magnesium (6), calcium (7), strontium (8) and barium (9) were prepared and fully characterized using elemental analysis, IR and NMR spectroscopy, DSC and TG analysis. All metal salts were characterized via single-crystal X-ray diffraction. They crystallize in common space groups with high densities ranging from 1.479 (1) to 3.060 g cm -3 (5). Furthermore, the crystal structures of 7, 8 and 9 reveal interesting porous energetic coordination polymers with strong hydrogen bond interactions. All new salts have good thermal stabilities with decomposition temperature between 215.0 °C (4) and 328.2 °C (7), significantly higher than that of the reported nitrogen-rich salt neutral tetrazolone. The sensitivities towards impact and friction were tested using standard methods, and all the tetrazolone-based compounds investigated can be classified into insensitive. The flame test of these metal salts supports their potential use as perchlorate-free pyrotechnics or eco-friendly insensitive energetic materials.

Modeling viscosity and conductivity of lithium salts in γ-butyrolactone

NASA Astrophysics Data System (ADS)

Chagnes, A.; Carré, B.; Willmann, P.; Lemordant, D.

Viscosity and conductivity properties of Li-salts (lithium tetrafluoroborate (LiBF 4), lithium hexafluorophosphate (LiPF 6), lithium hexafluoroarsenate (LiAsF 6), lithium bis-(trifluoromethylsulfone)-imide (LiTFSI)) dissolved in γ-butyrolactone (BL) have been investigated. The B- and D-coefficients of the Jones-Dole (JD) equation for the relative viscosity of concentrated electrolyte solutions (concentration: C=0.1-1.5 M): ηr=1+ AC1/2+ BC+ DC2, have been determined as a function of the temperature. The B-coefficient is linked to the hydrodynamic volume of the solute and remains constant within the temperature range investigated (25-55 °C). The D-coefficient, which originates mainly from long-range coulombic ion-ion interactions, is a reciprocal function of the temperature. The variations of the molar conductivity ( Λ) with C follow the cube root law Λ= Λ0'- S' C1/3 issued from quasi-lattice theory of electrolyte solutions. From the Walden product W= Λη which does not vary with C and the JD equation, the bell shape of the conductivity-concentration relationship is explained and it is shown that the concentration in salt at the maximum of conductivity is linked to the D-coefficient. Raman spectroscopy has been used as an additional tool to investigate ion pairing in BL. Ions pairs have been evidenced for LiClO 4 solutions in BL but not for LiPF 6. As little variations occur for the ions pairs dissociation coefficient when the salt concentration is increased, the cube root law remains valid, at least in the concentration range investigated.

Salting-out-enhanced ionic liquid microextraction with a dual-role solvent for simultaneous determination of trace pollutants with a wide polarity range in aqueous samples.

PubMed

Gao, Man; Qu, Jingang; Chen, Kai; Jin, Lide; Dahlgren, Randy Alan; Wang, Huili; Tan, Chengxia; Wang, Xuedong

2017-11-01

In real aquatic environments, many occupational pollutants with a wide range of polarities coexist at nanogram to milligram per liter levels. Most reported microextraction methods focus on extracting compounds with similar properties (e.g., polarity or specific functional groups). Herein, we developed a salting-out-enhanced ionic liquid microextraction based on a dual-role solvent (SILM-DS) for simultaneous detection of tetracycline, doxycycline, bisphenol A, triclosan, and methyltriclosan, with log K ow ranging from -1.32 to 5.40 in complex milk and environmental water matrices. The disperser in the ionic-liquid-based dispersive liquid-liquid microextraction was converted to the extraction solvent in the subsequent salting-out-assisted microextraction procedures, and thus a single solvent performed a dual role as both extractant and disperser in the SILM-DS process. Acetonitrile was selected as the dual-role solvent because of its strong affinity for both ionic liquids and water, as well as the extractant in the salting-out step. Optimized experimental conditions were 115 μL [C 8 MIM][PF 6 ] as extractor, 1200 μL acetonitrile as dual-role solvent, pH 2.0, 5.0 min ultrasound extraction time, 3.0 g Na 2 SO 4 , and 3.0 min vortex extraction time. Under optimized conditions, the recoveries of the five pollutants ranged from 74.5 to 106.9%, and their LODs were 0.12-0.75 μg kg -1 in milk samples and 0.11-0.79 μg L -1 in environmental waters. Experimental precision based on relative standard deviation was 1.4-6.4% for intraday and 2.3-6.5% for interday analyses. Compared with previous methods, the prominent advantages of the newly developed method are simultaneous determination of pollutants with a wide range of polarities and a substantially reduced workload for ordinary environmental monitoring and food tests. Therefore, the new method has great application potential for simultaneous determination of trace pollutants with strongly contrasting polarities in several analytical fields. Graphical Abstract A salting-out-enhanced ionic liquid microextraction based on a dual-role solvent (SILM-DS) was developed for simultaneous detection of tetracycline, doxycycline, bisphenol A, triclosan and methyltriclosan, with log K ow ranging from -1.32 to 5.40. The novelty of SILM-DS method lies in (1) simultaneous quantification of pollutants with contrasting polarity; (2) microextraction based on a dual-role solvent (as a disperser and extractant); (3) giving high recoveries for analytes with a wide range of polarities; and (4) reducing workload for ordinary environmental monitoring and food tests.

Post-production losses in iodine concentration of salt hamper the control of iodine deficiency disorders: a case study in northern Ethiopia.

PubMed

Shawel, Dawit; Hagos, Seifu; Lachat, Carl K; Kimanya, Martin E; Kolsteren, Patrick

2010-06-01

Iodine is essential for good function of the thyroid, and its deficiency is of public-health importance in Ethiopia. Iodization of salt is an effective and sustainable strategy to prevent and control iodine deficiency in large populations. The effectiveness of salt-iodization programmes depends on the conservation of iodine concentration in salt at various stages of the supply-chain. The overall objective of the study was to assess the loss of iodine in salt from production to consumption and to estimate the proportion of adults, especially pregnant women, at risk of dietary iodine insufficiency. A cross-sectional study was conducted during February-April 2007 in northern Ethiopia. Iodine concentrations of salt samples from producers (n=41), retailers (n=7), and consumers (n=32) were determined using iodiometric titration. A risk assessment was conducted for dietary iodine insufficiency among adults, including pregnant women, using a semi-probabilistic approach. The concentration of iodine in the sampled salts decreased by 57% from the production site to the consumers. The assessment of exposure showed that adults in 63% (n=20) of the households, including 90% (n=29) with pregnant women, were at risk of insufficient iodine intake. A monitoring and evaluation system needs to be established to ensure adequate supply of iodine along the distribution chain. Special attention is needed for the retailers and consumers. At these levels, dissemination of information regarding proper storage and handling of iodized salt is necessary to address the reported loss of iodine from salt.

The Rise and Fall of Universal Salt Iodization in Vietnam: Lessons Learned for Designing Sustainable Food Fortification Programs With a Public Health Impact.

PubMed

Codling, Karen; Quang, Nguyen Vinh; Phong, Le; Phuong, Do Hong; Quang, Nguyen Dinh; Bégin, France; Mathisen, Roger

2015-12-01

In 2005, more than 90% of Vietnamese households were using adequately iodized salt, and urinary iodine concentration among women of reproductive age was in the optimal range. However, household coverage declined thereafter to 45% in 2011, and urinary iodine concentration levels indicated inadequate iodine intake. To review the strengths and weaknesses of the Vietnamese universal salt iodization program from its inception to the current day and to discuss why achievements made by 2005 were not sustained. Qualitative review of program documents and semistructured interviews with national stakeholders. National legislation for mandatory salt iodization was revoked in 2005, and the political importance of the program was downgraded with consequential effects on budget, staff, and authority. The Vietnamese salt iodization program, as it was initially designed and implemented, was unsustainable, as salt iodization was not practiced as an industry norm but as a government-funded activity. An effective and sustainable salt iodization program needs to be reestablished for the long-term elimination of iodine deficiency, building upon lessons learned from the past and programs in neighboring countries. The new program will need to include mandatory legislation, including salt for food processing; industry responsibility for the cost of fortificant; government commitment for enforcement through routine food control systems and monitoring of iodine status through existing health/nutrition assessments; and intersectoral collaboration and management of the program. Many of the lessons would apply equally to universal salt iodization programs in other countries and indeed to food fortification programs in general. © The Author(s) 2015.

Salt content in canteen and fast food meals in Denmark

PubMed Central

Rasmussen, Lone Banke; Lassen, Anne Dahl; Hansen, Kirsten; Knuthsen, Pia; Saxholt, Erling; Fagt, Sisse

2010-01-01

Background A high salt (=NaCl) intake is associated with high blood pressure, and knowledge of salt content in food and meals is important, if the salt intake has to be decreased in the general population. Objective To determine the salt content in worksite canteen meals and fast food. Design For the first part of this study, 180 canteen meals were collected from a total of 15 worksites with in-house catering facilities. Duplicate portions of a lunch meal were collected from 12 randomly selected employees at each canteen on two non-consecutive days. For the second part of the study, a total of 250 fast food samples were collected from 52 retail places representing both city (Aarhus) and provincial towns. The canteen meals and fast food samples were analyzed for chloride by potentiometric titration with silver nitrate solution, and the salt content was estimated. Results The salt content in lunch meals in worksite canteens were 3.8±1.8 g per meal and 14.7±5.1 g per 10 MJ for men (n=109), and 2.8±1.2 g per meal and 14.4±6.2 g per 10 MJ for women (n=71). Salt content in fast food ranged from 11.8±2.5 g per 10 MJ (burgers) to 16.3±4.4 g per 10 MJ (sausages) with a mean content of 13.8±3.8 g per 10 MJ. Conclusion Salt content in both fast food and in worksite canteen meals is high and should be decreased. PMID:20305749

25 CFR 226.29 - Disposition of casings and other improvements.

Code of Federal Regulations, 2010 CFR

2010-04-01

... OSAGE RESERVATION LANDS FOR OIL AND GAS MINING Cessation of Operations § 226.29 Disposition of casings... 25 Indians 1 2010-04-01 2010-04-01 false Disposition of casings and other improvements. 226.29... bearing fresh water, oil, gas, salt water, and other minerals, and to protect it against invasion of...

40 CFR 147.1955 - Requirements for wells authorized by permit.

Code of Federal Regulations, 2010 CFR

2010-07-01

... (ii) Cemented back to the surface by recirculating the cement; and (2) Long string casing and tubing... volume. (3) For new enhanced recovery wells, install tubing or long string casing extending to the injection zone. (4) For new salt water disposal wells, install long string casing and tubing extending to...

Interactions of high-affinity cationic blockers with the translocation pores of B. anthracis, C. botulinum, and C. perfringens binary toxins.

PubMed

Bezrukov, Sergey M; Liu, Xian; Karginov, Vladimir A; Wein, Alexander N; Leppla, Stephen H; Popoff, Michel R; Barth, Holger; Nestorovich, Ekaterina M

2012-09-19

Cationic β-cyclodextrin derivatives were recently introduced as highly effective, potentially universal blockers of three binary bacterial toxins: anthrax toxin of Bacillus anthracis, C2 toxin of Clostridium botulinum, and iota toxin of Clostridium perfringens. The binary toxins are made of two separate components: the enzymatic A component, which acts on certain intracellular targets, and the binding/translocation B component, which forms oligomeric channels in the target cell membrane. Here we studied the voltage and salt dependence of the rate constants of binding and dissociation reactions of two structurally different β-cyclodextrins (AmPrβCD and AMBnTβCD) in the PA(63), C2IIa, and Ib channels (B components of anthrax, C2, and iota toxins, respectively). With all three channels, the blocker carrying extra hydrophobic aromatic groups on the thio-alkyl linkers of positively charged amino groups, AMBnTβCD, demonstrated significantly stronger binding compared with AmPrβCD. This effect is seen as an increased residence time of the blocker in the channels, whereas the time between blockages characterizing the binding reaction on-rate stays practically unchanged. Surprisingly, the voltage sensitivity, expressed as a slope of the logarithm of the blocker residence time as a function of voltage, turned out to be practically the same for all six cases studied, suggesting structural similarities among the three channels. Also, the more-effective AMBnTβCD blocker shows weaker salt dependence of the binding and dissociation rate constants compared with AmPrβCD. By estimating the relative contributions of the applied transmembrane field, long-range Coulomb, and salt-concentration-independent, short-range forces, we found that the latter represent the leading interaction, which accounts for the high efficiency of blockage. In a search for the putative groups in the channel lumen that are responsible for the short-range forces, we performed measurements with the F427A mutant of PA(63), which lacks the functionally important phenylalanine clamp. We found that the on-rates of the blockage were virtually conserved, but the residence times and, correspondingly, the binding constants dropped by more than an order of magnitude, which also reduced the difference between the efficiencies of the two blockers. Copyright © 2012 Biophysical Society. Published by Elsevier Inc. All rights reserved.

Effects of Imide–Orthoborate Dual-Salt Mixtures in Organic Carbonate Electrolytes on the Stability of Lithium Metal Batteries

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Xing; Zheng, Jianming; Engelhard, Mark H.

The effects of lithium imide and lithium orthoborate dual-salt electrolytes of different salt chemistries in carbonate solvents on the cycling stability of Li metal batteries were systematically and comparatively investigated. Two imide salts (LiTFSI and LiFSI) and two orthoborate salts (LiBOB and LiDFOB) were chosen for this study and compared with the conventional LiPF6 salt. The cycling stability of the Li metal cells with the electrolytes follows the order from good to poor as LiTFSI-LiBOB > LiTFSI-LiDFOB > LiPF6 > LiFSI-LiBOB > LiFSI-LiDFOB, indicating that LiTFSI behaves better than LiFSI and LiBOB over LiDFOB in these four dual-salt mixtures. Themore » LiTFSI-LiBOB can effectively protect the Al substrate and form a more robust surface film on Li metal anode, while the LiFSI-LiBOB results in serious corrosion to the stainless steel cell case and a thicker and looser surface film on Li anode. Computational calculations indicate that the chemical and electrochemical stabilities also follow the order of LiTFSI-LiBOB > LiTFSI-LiDFOB > LiFSI-LiBOB > LiFSI-LiDFOB. The key findings of this work emphasize that the salt chemistry is critically important for enhancing the interfacial stability of Li metal anode and should be carefully manipulated in the development of high performance Li metal batteries.« less

Carbonates and sulfates in the Chassigny meteorite: Further evidence for aqueous chemistry on the SNC parent planet

NASA Technical Reports Server (NTRS)

Wentworth, Susan J.; Gooding, James L.

1994-01-01

Scanning electron microscopy and energy-dispersive X-ray spectrometry of untreated interior chips from three different specimens of the Chassigny meteorite confirm the presence of discrete grains of Ca-carbonate, Mg-carbonate, and Ca-sulfate. Morphologies of these salt grains suggest that the Ca-carbonate is calcite (CaCO3) and that the Ca-sulfate is gypsum (CaSO4-2H2O) or bassanite (CaSO4-1/2H2O). The morphologic identification of the Mg-carbonate is equivocal, but rhombohedral and acicular crystal habits suggest magnesite and hydromagnesite, respectively. The salts in Chassigny occur as discontinuous veins in primary igneous minerals and are similar to those previously documented in the nakhlites, Nakhla and Lafayette, and in shergottite EETA79001. Unlike those in nakhlites, however, the Chassigny salts occur alone, without associated ferric oxides or aluminosilicates clays. Traces of Cl and P in Chassigny salts are consistent with precipitation of the salts from short-lived, saline, aqueous solutions that postdated igneous crystallization. In contrast with the clear case for nakhlites, stratigraphic evidence for a preterrestrial origin of the salts in Chassigny is ambiguous; however, a preterrestrial origin of the Chassigny salts best explains all available evidence. The water-precipitated salts provide clear physical evidence for the hypothesis, proposed by other workers, that the igneous amphiboles in Chassigny might have experienced isotope-exchange reactions with near-surface water, thereby compromising the original stable-isotope signature of any magmatic water in melt inclusions.

A simple definitive test for chloride salts on Europa

NASA Astrophysics Data System (ADS)

Brown, Michael

2016-10-01

Europa is a prime location for exploring our concepts of habitability throughout the solar system. As importantly, Europa is a case study for how liquid water drives the geochemistry and geophysics in a world very different from our own. One of the keys to understanding the liquid water's effect on habitability, geochemistry, and even on geophysics is understanding the chemistry of the internal ocean. Evaporites on the surface of Europa provide a window into this ocean chemistry. Recent observations have overturned 15 years worth of assumptions about the chemistry of Europa's ocean and have suggested that chloride salts - rather than sulfate salts - could be the most abundant constituent in the ocean and in the surface evaporites. The possibility of chloride salts has major implications for geophysics and habitability, but, because chloride salts are basically featureless, definitive spectral evidence was thought impossible.New laboratory data now shows, however, that electron irradiation with Europa-like fluxes imparts distinct spectral absorption features on chloride salts. These spectral features, in specific bands between 430 and 830 nm, are uniquely accessible to high spatial resolution HST spectroscopy. We propose a very simple program to obtain four separate high spatial resolution STIS slit scans across the disk of Europa to construct a global spectral map which will detect and map these surface salts. These observations can definitively identify chloride salts on Europa and fundamentally change our understanding of this world. Rarely can such a simple and short program with HST have the possibility of obtaining such conclusive and transformative results.

Separation of CsCl from a Ternary CsCl-LiCl-KCl Salt via a Melt Crystallization Technique for Pyroprocessing Waste Minimization

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ammon Williams; Supathorn Phongikaroon; Michael Simpson

A parametric study has been conducted to identify the effects of several parameters on the separation of CsCl from molten LiCl-KCl salt via a melt crystallization process. A reverse vertical Bridgman technique was used to grow the salt crystals. The investigated parameters were: (1) the advancement rate, (2) the crucible lid configuration, (3) the amount of salt mixture, (4) the initial composition of CsCl, and (5) the temperature difference between the high and low furnace zones. From each grown crystal, samples were taken axially and analyzed using inductively coupled plasma mass spectrometry (ICP-MS). Results show that CsCl concentrations at themore » top of the crystals were low and increased to a maximum at the bottom of the salt. Salt (LiCl-KCl) recycle percentages for the experiments ranged from 50% to 75% and the CsCl composition in the waste salt was low. To increase the recycle percentage and the concentration of CsCl in the waste form, the possibility of using multiple crystallization stages was explored to further optimize the process. Results show that multiple crystallization stages are practical and the optimal experimental conditions should be operated at 5.0 mm/hr rate with a lid configuration and temperature difference of 200 °C for a total of five crystallization stages. Under these conditions, up to 88% of the salt can be recycled.« less

Evaluation of who oral rehydration solution (ORS) and salt tablets in resuscitating adult patients with burns covering more than 15% of total body surface area (TBSA).

PubMed

Moghazy, A M; Adly, O A; Elbadawy, M A; Hashem, R E

2016-03-31

Intra-venous (IV) burn resuscitation is effective; nevertheless it has its disadvantages. WHO Oral Rehydration Solution (ORS) has shown high effectiveness in treating dehydration. WHO-ORS, with salt supplement, seems to be suitable for burn resuscitation, where IV resuscitation is not available, feasible or possible. The objective of the study was to evaluate acute phase efficacy and safety, as well as limitations and complications of burn resuscitation using WHO-ORS and salt tablets. This randomized controlled clinical trial was conducted in the Burn Unit, Suez Canal University Hospital, Ismailia, Egypt. The study group was given WHO-ORS (15% of body weight/day) with one salt tablet (5gm) per liter according to Sørensen's formula. The control group was given IV fluids according to the Parkland formula. Patients' vital signs and urine output were monitored for 72 hours after starting resuscitation. Both groups were comparable regarding age, sex, and percentage, etiology and degree of burns. For all assessed parameters, there were no major significant differences between the study group (10 cases) and control group (20 cases). Even where there was a significant difference, apart from blood pressure in the first hour of the first day, the study group never crossed safe limits for pulse, systolic blood pressure, urine output, respiratory rate and conscious level. WHO-ORS with 5gm salt tablets, given according to Sørenson's formula, is a safe and efficient alternative for IV resuscitation. It could even be a substitute, particularly in low resource settings and fire disasters.

Great Salt Lake Composition and Rare Earth Speciation Analysis

DOE Data Explorer

Jiao, Yongqin; Lammers, Laura; Brewer, Aaron

2017-04-19

We have conducted aqueous speciation analyses of the Great Salt Lake (GSL) brine sample (Table 1) and a mock geo sample (Table 2) spiked with 1 ppb Tb and 100 ppb Tb. The GSL speciation (Figure 1) aligns with our basic speciation expectations that strong carbonate complexes would form at mid to higher pH's. Although we expected strong aqueous complexes with fluorides at neutral pH and with chlorides, and hydroxides at low pH, we observe that the dominant species in the low to mid pH range to be Tb3+ as a free ion. Still, we do see the presence of fluoride and chloride complexes within the expected low to mid pH range.

KSC-99wl10

NASA Image and Video Library

1999-01-08

KENNEDY SPACE CENTER, FLA. -- Ducks take flight across the marshes of the Merritt Island National Wildlife Refuge at Kennedy Space Center. The duck at top-center is a pintail, which can be found in marshes, prairie ponds and tundra, and salt marshes in winter. They range from Alaska and Greenland south to Central America and the West Indies. The open waters of the Wildlife Refuge provide wintering areas for 23 species of migratory waterfowl as well as a year-round home for great blue herons, great egrets, wood storks, cormorants, brown pelicans and other species of marsh and shore birds. The refuge comprises 92,000 acres, ranging from fresh-water impoundments, salt-water estuaries and brackish marshes to hardwood hammocks and pine flatwoods

Helix–hairpin–helix motifs confer salt resistance and processivity on chimeric DNA polymerases

PubMed Central

Pavlov, Andrey R.; Belova, Galina I.; Kozyavkin, Sergei A.; Slesarev, Alexei I.

2002-01-01

Helix–hairpin–helix (HhH) is a widespread motif involved in sequence-nonspecific DNA binding. The majority of HhH motifs function as DNA-binding modules with typical occurrence of one HhH motif or one or two (HhH)2 domains in proteins. We recently identified 24 HhH motifs in DNA topoisomerase V (Topo V). Although these motifs are dispensable for the topoisomerase activity of Topo V, their removal narrows the salt concentration range for topoisomerase activity tenfold. Here, we demonstrate the utility of Topo V's HhH motifs for modulating DNA-binding properties of the Stoffel fragment of TaqDNA polymerase and Pfu DNA polymerase. Different HhH cassettes fused with either NH2 terminus or COOH terminus of DNA polymerases broaden the salt concentration range of the polymerase activity significantly (up to 0.5 M NaCl or 1.8 M potassium glutamate). We found that anions play a major role in the inhibition of DNA polymerase activity. The resistance of initial extension rates and the processivity of chimeric polymerases to salts depend on the structure of added HhH motifs. Regardless of the type of the construct, the thermal stability of chimeric Taq polymerases increases under the optimal ionic conditions, as compared with that of TaqDNA polymerase or its Stoffel fragment. Our approach to raise the salt tolerance, processivity, and thermostability of Taq and Pfu DNA polymerases may be applied to all pol1- and polB-type polymerases, as well as to other DNA processing enzymes. PMID:12368475

Transport and fate of chloride from road salt within a mixed urban and agricultural watershed in Illinois (USA): assessing the influence of chloride application rates

NASA Astrophysics Data System (ADS)

Ludwikowski, Jessica J.; Peterson, Eric W.

2018-06-01

In a typical winter season, approximately 471,000 tons of road salt are deposited along roadways in Illinois, USA. An estimated 45% of the deposited road salt will infiltrate through the soils and into shallow aquifers. Transported through shallow aquifers, chloride associated with the road salts has the potential to reside within groundwater for years based on the pathway, the geologic material, and the recharge rate of the aquifer system. Utilizing MODFLOW and MT3D, simulations employing various road-salt application rates were conducted to assess the net accumulation of chloride and the residence times of chloride in an agriculture-dominated watershed that originates in an urban area. A positive-linear relationship was observed between the application rate of chloride and both the maximum chloride concentration and total mass accumulated within the watershed. Simulated annual recharge rates along impacted surfaces ranged from 1,000 to 10,000 mg/L. After 60 years of application, simulated chloride concentrations in groundwater ranged from 197 to 1,900 mg/L. For all application rates, chloride concentrations within the groundwater rose at an annual rate of >3 mg/L. While concentrations increase throughout the system, the majority of chloride accumulation occurs near the roads and the urban areas. Model simulations reveal a positive relationship between application rate and residence time of chloride (1,123-1,288 days based on application rate). The models indicate that continued accumulation of chloride in shallow aquifers can be expected, and methods that apply less chloride effectively need to be examined.

Synthesis of LaMnO3 in molten chlorides: effect of preparation conditions.

PubMed

Vradman, Leonid; Zana, Jonatan; Kirschner, Alon; Herskowitz, Moti

2013-07-14

LaMnO3 perovskite was successfully synthesized in molten chlorides. In order to explore the effect of the molten salt type, NaCl-KCl and LiCl-KCl eutectic mixtures were employed as a liquid medium for the perovskite formation process. The synthesis included heating the La-nitrate, Mn-nitrate and chlorides mixture to above the melting point of the corresponding chlorides. This procedure yielded a LaMnO3 phase integrated in the fused chloride matrix. Washing with water removed the salts completely, yielding pure LaMnO3 perovskite crystals. The synthesis without molten salt at 800 °C yielded several by-products in addition to the LaMnO3 phase, while with LiCl-KCl the pure perovskite phase was obtained at temperatures as low as 600 °C. Variation of temperature in the range 600-800 °C for LiCl-KCl and 700-800 °C for NaCl-KCl had no significant effect either on the morphology or on the particle size of the product. On the other hand, the effect of the molten salt type on the morphology and size of perovskite particles was remarkable. The synthesis in NaCl-KCl resulted in sub-micron LaMnO3 particles with shapes that range from truncated hexahedrons to spheres, while in LiCl-KCl mostly cubic particles of up to 2-microns were obtained. The effect of the molten salt type on LaMnO3 perovskite formation is explained based on the nucleation and crystal growth model and difference in the melting point of eutectic mixtures.

Transport and fate of chloride from road salt within a mixed urban and agricultural watershed in Illinois (USA): assessing the influence of chloride application rates

NASA Astrophysics Data System (ADS)

Ludwikowski, Jessica J.; Peterson, Eric W.

2018-01-01

In a typical winter season, approximately 471,000 tons of road salt are deposited along roadways in Illinois, USA. An estimated 45% of the deposited road salt will infiltrate through the soils and into shallow aquifers. Transported through shallow aquifers, chloride associated with the road salts has the potential to reside within groundwater for years based on the pathway, the geologic material, and the recharge rate of the aquifer system. Utilizing MODFLOW and MT3D, simulations employing various road-salt application rates were conducted to assess the net accumulation of chloride and the residence times of chloride in an agriculture-dominated watershed that originates in an urban area. A positive-linear relationship was observed between the application rate of chloride and both the maximum chloride concentration and total mass accumulated within the watershed. Simulated annual recharge rates along impacted surfaces ranged from 1,000 to 10,000 mg/L. After 60 years of application, simulated chloride concentrations in groundwater ranged from 197 to 1,900 mg/L. For all application rates, chloride concentrations within the groundwater rose at an annual rate of >3 mg/L. While concentrations increase throughout the system, the majority of chloride accumulation occurs near the roads and the urban areas. Model simulations reveal a positive relationship between application rate and residence time of chloride (1,123-1,288 days based on application rate). The models indicate that continued accumulation of chloride in shallow aquifers can be expected, and methods that apply less chloride effectively need to be examined.

Salt effects in surfactant-free microemulsions

NASA Astrophysics Data System (ADS)

Schöttl, Sebastian; Horinek, Dominik

2018-06-01

The weakly associated micellar aggregates found in the so-called "pre-ouzo region" of the surfactant-free microemulsion water/ethanol/1-octanol are sensitive to changes in the system composition and also to the presence of additives like salt. In this work, we study the influence of two salts, sodium iodide and lithium chloride, on aggregates in water/ethanol/1-octanol by molecular dynamics simulations. In both cases, ethanol concentration in the nonpolar phase and at the interface is increased due to a salting out effect on ethanol in the aqueous pseudo-phase. In addition, minor charging of the interface as a consequence of differential adsorption of anions and cations occurs. However, this charge separation is overall weakened by the erratic surface of octanol aggregates, where polar hydroxyl groups and hydrophobic patches are both present. Furthermore, ethanol at the interface shields hydrophobic patches and reduces the preferential adsorption of iodide and lithium.

Method of treating waste water

DOEpatents

Deininger, J. Paul; Chatfield, Linda K.

1991-01-01

A process of treating water to remove transuranic elements contained therein by adjusting the pH of a transuranic element-containing water source to within the range of about 6.5 to about 14.0, admixing the water source with an alkali or alkaline earth ferrate in an amount sufficient to form a precipitate within the water source, the amount of ferrate effective to reduce the transuranic element concentration in the water source, permitting the precipitate in the admixture to separate and thereby yield a supernatant liquid having a reduced transuranic element concentration, and separating the supernatant liquid having the reduced transuranic element concentration from the admixture is provided. Additionally, a water soluble salt, e.g., a zirconium salt, can be added with the alkali or alkaline earth ferrate in the process to provide greater removal efficiencies. A composition of matter including an alkali or alkaline earth ferrate and a water soluble salt, e.g., a zirconium salt, is also provided.

Effects of preservation methods on amino acids and 5'-nucleotides of Agaricus bisporus mushrooms.

PubMed

Liu, Ying; Huang, Fan; Yang, Hong; Ibrahim, S A; Wang, Yan-Feng; Huang, Wen

2014-04-15

In this study, the proximate composition, free amino acids content and 5'-nucleotides in frozen, canned and salted Agaricus bisporus (A. bisporus) were investigated. We found that the three kinds of A. bisporus products were good sources of protein, with amount varying in the ranges of 16.54-24.35g/100g (dry weight). Freezing, canning and salting process, followed by 6months of storage led to a significant reduction in free amino acids, especially tyrosine, alanine, glutamine and cysteine. There were medium levels of MSG-like amino acids in frozen A. bisporus and canned A. bisporus, and low levels of MSG-like amino acids in salted A. bisporus. The mount of flavor 5'-nucleotides in frozen A. bisporus was higher than that of canned and salted A. bisporus. The present study thus suggests that freezing is beneficial for the preservation of A. bisporus. Copyright © 2013 Elsevier Ltd. All rights reserved.

Effects of pretreatment processes for Zr electrorefining of oxidized Zircaloy-4 cladding tubes

NASA Astrophysics Data System (ADS)

Hwa Lee, Chang; Lee, Yoo Lee; Jeon, Min Ku; Choi, Yong Taek; Kang, Kweon Ho; Park, Geun Il

2014-06-01

The effect of pretreatment processes for the Zr electrorefining of oxidized Zircaloy-4 cladding tubes is examined in LiCl-KCl-ZrCl4 molten salts at 500 °C. The cyclic voltammetries reveal that the Zr dissolution kinetics is highly dependent on the thickness of a Zr oxide layer formed at 500 °C under air atmosphere. For the Zircaloy-4 tube covered with a 1 μm thick oxide layer, the Zr dissolution process is initiated from a non-stoichiometric Zr oxide surface through salt treatment at an open circuit potential in the molten salt electrolyte. The Zr dissolution of the samples in the middle range of oxide layer thickness appears to be more effectively derived by the salt treatment coupled with an anodic potential application at an oxidation potential of Zr. A modification of the process scheme offers an applicability of Zr electrorefining for the treatment of oxidized cladding hull wastes.

Tuneable enhancement of the salt and thermal stability of polymeric micelles by cyclized amphiphiles

PubMed Central

Honda, Satoshi; Yamamoto, Takuya; Tezuka, Yasuyuki

2013-01-01

Cyclic molecules provide better stability for their aggregates. Typically in nature, the unique cyclic cell membrane lipids allow thermophilic archaea to inhabit extreme conditions. By mimicking the biological design, the robustness of self-assembled synthetic nanostructures is expected to be improved. Here we report topology effects by cyclized polymeric amphiphiles against their linear counterparts, demonstrating a drastic enhancement in the thermal, as well as salt stability of self-assembled micelles. Furthermore, through coassembly of the linear and cyclic amphiphiles, the stability was successfully tuned for a wide range of temperatures and salt concentrations. The enhanced thermal/salt stability was exploited in a halogen exchange reaction to stimulate the catalytic activity. The mechanism for the enhancement was also investigated. These topology effects by the cyclic amphiphiles offer unprecedented opportunities in polymer materials design unattainable by traditional means. PMID:23481382

Prediction of heat capacities of solid inorganic salts from group contributions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mostafa, A.T.M.G.; Eakman, J.M.; Yarbro, S.L.

1997-01-01

A group contribution technique is proposed to predict the coefficients in the heat capacity correlation, C{sub p} = a + bT + c/T{sup 2} + dT{sup 2}, for solid inorganic salts. The results from this work are compared with fits to experimental data from the literature. It is shown to give good predictions for both simple and complex solid inorganic salts. Literature heat capacities for a large number (664) of solid inorganic salts covering a broad range of cations (129), anions (17) and ligands (2) have been used in regressions to obtain group contributions for the parameters in the heatmore » capacity temperature function. A mean error of 3.18% is found when predicted values are compared with literature values for heat capacity at 298{degrees} K. Estimates of the error standard deviation from the regression for each additivity constant are also determined.« less

Extraction, scrub, and strip test results for the solvent transfer to salt waste processing facility

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peters, T.

The Savannah River National Laboratory (SRNL) prepared approximately 240 gallons of Caustic-Side Solvent Extraction (CSSX) solvent for use at the Salt Waste Processing Facility (SWPF). An Extraction, Scrub, and Strip (ESS) test was performed on a sample of the prepared solvent using a salt solution prepared by Parsons to determine cesium distribution ratios (D(Cs)), and cesium concentration in the strip effluent (SE) and decontaminated salt solution (DSS) streams. This data will be used by Parsons to help qualify the solvent for use at the SWPF. The ESS test showed acceptable performance of the solvent for extraction, scrub, and strip operations.more » The extraction D(Cs) measured 15.5, exceeding the required value of 8. This value is consistent with results from previous ESS tests using similar solvent formulations. Similarly, scrub and strip cesium distribution ratios fell within acceptable ranges.« less

Lithium salts based on a series of new anilinyl-perfluorosulfonamide salts and their polymer electrolytes

NASA Astrophysics Data System (ADS)

Thiam, A.; Iojoiu, C.; Leprêtre, J.-C.; Sanchez, J.-Y.

2017-10-01

Polymer electrolytes based on a series of new lithium anilinyl-perfluorosulfonamide exhibit conductivities close to LiTFSI ones and higher cationic transference numbers. Taking advantage of an extended delocalization on the negative charge, the anodic stability of the salts was found to range between 4.2 and 4.9 V vs Li/Li+, according to the electron-withdrawing group EWG located in para/ortho position. The simplicity of the synthesis process of the new salts, with lower fluorine content than LiPF6 and LiTFSI, paves the way for a further semi-pilot scale-up. Moreover, Linear Free Energy Relationships, LFER, were established for the first time, for both ionic conductivity and anodic stability. These LFER demonstrate unambiguously and quantitatively the conductivity dependence on anion basicity. Polymer electrolytes were soundly investigated through a variety of physicochemical and electrochemical characterizations.

Flight experiment of thermal energy storage. [for spacecraft power systems

NASA Technical Reports Server (NTRS)

Namkoong, David

1989-01-01

Thermal energy storage (TES) enables a solar dynamic system to deliver constant electric power through periods of sun and shade. Brayton and Stirling power systems under current considerations for missions in the near future require working fluid temperatures in the 1100 to 1300+ K range. TES materials that meet these requirements fall into the fluoride family of salts. Salts shrink as they solidify, a change reaching 30 percent for some salts. Hot spots can develop in the TES container or the container can become distorted if the melting salt cannot expand elsewhere. Analysis of the transient, two-phase phenomenon is being incorporated into a three-dimensional computer code. The objective of the flight program is to verify the predictions of the code, particularly of the void location and its effect on containment temperature. The four experimental packages comprising the program will be the first tests of melting and freezing conducted under microgravity.

[Microbial diversity of salt lakes in Badain Jaran desert].

PubMed

Li, Lu; Hao, Chunbo; Wang, Lihua; Pei, Lixin

2015-04-04

We characterized procaryotic biodiversity, community structure and the relationship between the community structure and environmental factors of salt lakes in Badain Jaran desert, Inner Mongolia, China. We constructed 16S rRNA gene clone libraries by molecular biology techniques to analyze the procaryotic phylogenetic relationships, and used R language to compare the community structure of haloalkalophiles in the salt lakes. Water in this region has a high salinity ranging from 165 to 397 g/L. The water is strongly alkaline with pH value above 10. The microbial diversity and community structure of the salt lakes are obviously different. The diversity of bacteria is more abundant than that of archaea. The main categories of bacteria in the samples are Gammaproteobacteria, Bacteroidetes, Alphaproteobacteria, Firmicute and Verrucomicrobia, whereas all archaea only belong to Halobacteriaceae of Euryarchaeota. Salinity is the most important environmental factor influencing the bacterial community structure, whereas the archaea community structure was influenced comprehensively by multiple environmental factors.

The Effect of Salt on the Complex Coacervation of Vinyl Polyelectrolytes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Perry, Sarah; Li, Yue; Priftis, Dimitrios

2014-06-01

Complex coacervation is an electrostatically-driven phase separation phenomenon that is utilized in a wide range of everyday applications and is of great interest for the creation of self-assembled materials. Here, we utilized turbidity to characterize the effect of salt type on coacervate formation using two vinyl polyelectrolytes, poly(acrylic acid sodium salt) (pAA) and poly(allylamine hydrochloride) (pAH), as simple models for industrial and biological coacervates. We confirmed the dominant role of salt valence on the extent of coacervate formation, while demonstrating the presence of significant secondary effects, which can be described by Hofmeister-like behavior. These results revealed the importance of ion-specificmore » interactions, which are crucial for the informed design of coacervate-based materials for use in complex ionic environments, and can enable more detailed theoretical investigations on the role of subtle electrostatic and thermodynamic effects in complex coacervation.« less

Manufacture, distribution, and handling of nitrate salts for solar-thermal applications

NASA Astrophysics Data System (ADS)

Fiorucci, L. C.; Goldstein, S. L.

1982-11-01

The low cost and attractive physical properties of molten sodium/potassium nitrate salts were shown to be one of the most cost effective fluids for heat absorption and thermal energy storage in Solar Central Receiver (SCR) systems. Information related to the availability, transport, handling, and utilization of these salts for commercial size SCR applications is provided. The following items are reviewed: existing manufacturing processes for natural and synthetic nitrates; the upstream availability of raw materials; downstream existing and projected demand for these products in other sectors of the economy; and relevant handling and distribution technologies. Safety considerations and issues more directly related to the SCR facility, such as initial system charging, salt maintenance and regeneration, and disposal are also reviewed. Options for supply, surge storage, and initial charging are discussed for the 1 MWt to 300 MWe range of solar plant sizes.