Effect of various conditions on inactivation of Escherichia coli O157:H7, Salmonella Typhimurium, and Listeria monocytogenes in fresh-cut lettuce using ultraviolet radiation.

PubMed

Kim, Yoon-Hee; Jeong, Seul-Gi; Back, Kyeong-Hwan; Park, Ki-Hwan; Chung, Myung-Sub; Kang, Dong-Hyun

2013-09-16

The effect of various conditions on inactivation of foodborne pathogens and quality of fresh-cut lettuce during ultraviolet (254 nm, UVC) radiation was investigated. Lettuce was inoculated with a cocktail of Escherichia coli O157:H7, Salmonella Typhimurium, and Listeria monocytogenes and treated at different temperatures (4 and 25 °C), distances between sample and lamp (10 and 50 cm), type of exposure (illuminated from one or two sides), UV intensities (1.36 to 6.80 mW/cm²), and exposure times (0.5 to 10 min), sequentially. UV treatment at 25 °C for 1 min achieved 1.45-, 1.35-, and 2.12-log reductions in surface-inoculated E. coli O157:H7, S. Typhimurium, and L. monocytogenes, respectively, whereas the reduction of these pathogens at 4 °C was 0.31, 0.57, and 1.16 log, respectively. UV radiation was most effective when distance from UV lamp to the sample was minimal (10 cm) and radiation area was maximal (two-sided exposure). All UV intensities significantly (P<0.05) reduced the three pathogens after 10 min exposure, but the effect of treatment was correlated with UV intensity and exposure time. Color values and texture parameters of lettuce subjected to UV treatment under the optimum conditions (25 °C, 10 cm between sample and lamp, two-sided exposure, 6.80 mW/cm²) were not significantly (P>0.05) different from those of nontreated samples up to 5 min exposure. However, these qualities significantly (P<0.05) changed at prolonged treatment time. These results suggest that UV radiation under optimized conditions could reduce foodborne pathogens without adversely affecting color quality properties of fresh-cut lettuce. © 2013 Elsevier B.V. All rights reserved.

Biological response in vitro of skeletal muscle cells treated with different intensity continuous and pulsed ultrasound fields

NASA Astrophysics Data System (ADS)

Abrunhosa, Viviane M.; Mermelstein, Claudia S.; Costa, Manoel L.; Costa-Felix, Rodrigo P. B.

2011-02-01

Therapeutic ultrasound has been used in physiotherapy to accelerate tissue healing. Although the ultrasonic wave is widely used in clinical practice, not much is known about the biological effects of ultrasound on cells and tissues. This study aims to evaluate the biological response of ultrasound in primary cultures of chick myogenic cells. To ensure the metrological reliability of whole measurement process, the ultrasound equipment was calibrated in accordance with IEC 61689:2007. The skeletal muscle cells were divided in four samples. One sample was used as a control group and the others were submitted to different time and intensity and operation mode of ultrasound: 1) 0.5 W/cm2 continuous for 5 minutes, 2) 0.5 W/cm2 pulsed for 5 minutes, 3) 1.0 W/cm2 pulsed for 10 minutes. The samples were analyzed with phase contrast optical microscopy before and after the treatment. The results showed alignment of myogenic cells in the sample treated with 0.5 W/cm2 continuous during 5 minutes when compared with the control group and the other samples. This study is a first step towards a metrological and scientific based protocol to cells and tissues treatment under different ultrasound field exposures.

Americium-241 in surface soil associated with the Hanford site and vicinity

DOE Office of Scientific and Technical Information (OSTI.GOV)

Price, K.R.; Gilbert, R.O.; Gano, K.A.

1981-05-01

Various kinds of surface soil samples were collected and analyzed for Americium-241 (/sup 241/Am) to examine the feasibility of improving soil sample data for the Hanford Surface Environmental Surveillance Program. Results do not indicate that a major improvement would occur if procedures were changed from the current practices. Conclusions from this study are somewhat tempered by the very low levels of /sup 241/Am (< 0.10 pCi/g dry weight) detected in surface soil samples and by the fact that statistical significance depended on the type of statistical tests used. In general, the average concentration of /sup 241/Am in soil crust (0more » to 1.0 cm deep) was greater than the corresponding subsurface layer (1.0 to 2.5 cm deep), and the average concentration of /sup 241/Am in some onsite samples collected near the PUREX facility was greater than comparable samples collected 60 km upwind at an offsite location.« less

Hyperspectral Signatures (400 to 2500 nm) of Vegetation, Minerals, Soils, Rocks, and Cultural Features: Laboratory and Field Measurements

DTIC Science & Technology

1990-12-01

nadir radiometer viewing angle. The reference standard was a 25.4 cm x 25.4 cm x 1.0 cm pressed Halon "Spectralon" plate that was backed by a 0.5 cm...against the sphere’s sample port. Light transmitted through the leaf was trapped in the sample chamber and did not pass back into the integrating sphere...leaf layers. The leaves were added to the back of the stack, so leaf #1 was always the first leaf in the stack. Each spectrum was taken in the lower 1

Identification and characteristics of biological agents in work environment of medical emergency services in selected ambulances.

PubMed

Bielawska-Drózd, Agata; Cieślik, Piotr; Wlizło-Skowronek, Bożena; Winnicka, Izabela; Kubiak, Leszek; Jaroszuk-Ściseł, Jolanta; Depczyńska, Daria; Bohacz, Justyna; Korniłłowicz-Kowalska, Teresa; Skopińska-Różewska, Ewa; Kocik, Janusz

2017-06-19

Assessment of microbial air quality and surface contamination in ambulances and administration offices as a control place without occupational exposure to biological agents; based on quantitative and qualitative analysis of bacteria, yeasts and filamentous fungi found in collected samples. The sampling was done by wet cyclone technology using the Coriolis recon apparatus, imprint and swab methods, respectively. In total, 280 samples from 28 ambulances and 10 offices in Warszawa were tested. Data was analyzed using Shapiro-Wilk normality test, Kruskal-Wallis test with α = 0.05. P value ≤ 0.05 was considered as significant. The levels of air contamination were from 0 to 2.3×10¹ colony-forming unit (CFU)/m³ for bacteria and for yeast and filamentous fungi were from 0 to 1.8×10¹ CFU/m³. The assessment of office space air samples has shown the following numbers of microorganisms: bacteria from 3.0×10¹ to 4.2×10¹ CFU/m³ and yeast and filamentous fungi from 0 to 1.9×10¹ CFU/m³. For surface contamination the mean bacterial count in ambulances has been between 1.0×10¹ and 1.3×10² CFU/25 cm² and in offices - between 1.1×10¹ and 8.5×10¹ CFU/25 cm². Mean fungal count has reached the level from 2.8×10⁰ to 4.2×10¹ CFU/25 cm² in ambulances and 1.3×10¹ to 5.8×10¹ CFU/25 cm² in offices. The qualitative analysis has revealed the presence of Acinetobacter spp. (surfaces), coagulase - negative Staphylococci (air and surfaces), Aspergillus and Penicillium genera (air and surfaces). The study has revealed a satisfactory microbiological quantity of analyzed air and surface samples in both study and control environments. However, the presence of potentially pathogenic microorganisms in the air and on surfaces in ambulances may endanger the medical emergency staff and patients with infection. Disinfection and cleaning techniques therefore should be constantly developed and implemented. Int J Occup Med Environ Health 2017;30(4):617-627. This work is available in Open Access model and licensed under a CC BY-NC 3.0 PL license.

Effect of Wind Velocity on Flame Spread in Microgravity

NASA Technical Reports Server (NTRS)

Prasad, Kuldeep; Olson, Sandra L.; Nakamura, Yuji; Fujita, Osamu; Nishizawa, Katsuhiro; Ito, Kenichi; Kashiwagi, Takashi; Simons, Stephen N. (Technical Monitor)

2002-01-01

A three-dimensional, time-dependent model is developed describing ignition and subsequent transition to flame spread over a thermally thin cellulosic sheet heated by external radiation in a microgravity environment. A low Mach number approximation to the Navier Stokes equations with global reaction rate equations describing combustion in the gas phase and the condensed phase is numerically solved. The effects of a slow external wind (1-20 cm/s) on flame transition are studied in an atmosphere of 35% oxygen concentration. The ignition is initiated at the center part of the sample by generating a line-shape flame along the width of the sample. The calculated results are compared with data obtained in the 10s drop tower. Numerical results exhibit flame quenching at a wind speed of 1.0 cm/s, two localized flames propagating upstream along the sample edges at 1.5 cm/s, a single line-shape flame front at 5.0 cm/s, three flames structure observed at 10.0 cm/s (consisting of a single line-shape flame propagating upstream and two localized flames propagating downstream along sample edges) and followed by two line-shape flames (one propagating upstream and another propagating downstream) at 20.0 cm/s. These observations qualitatively compare with experimental data. Three-dimensional visualization of the observed flame complex, fuel concentration contours, oxygen and reaction rate isosurfaces, convective and diffusive mass flux are used to obtain a detailed understanding of the controlling mechanism, Physical arguments based on lateral diffusive flux of oxygen, fuel depletion, oxygen shadow of the flame and heat release rate are constructed to explain the various observed flame shapes.

Electrical characterization of 6H crystalline silicon carbide. M.S. Thesis Final Report

NASA Technical Reports Server (NTRS)

Lempner, Stephen E.

1994-01-01

Crystalline silicon carbide (SiC) substrates and epilayers, undoped as well as n- and p-doped, have been electrically characterized by performing Hall effect and resistivity measurements (van der Pauw) over the temperature range of approximately 85 K to 650 K (200 K to 500 K for p-type sample). By fitting the measured temperature dependent carrier concentration data to the single activation energy theoretical model: (1) the activation energy for the nitrogen donor ranged from 0.078 eV to 0.101 eV for a doping concentration range of 10(exp 17) cm(exp -3) to 10(exp 18) cm(exp -3) and (2) the activation energy for the aluminum acceptor was 0.252 eV for a doping concentration of 4.6 x 10(exp 18) cm(exp -3). By fitting the measured temperature dependent carrier concentration data to the double activation energy level theoretical model for the nitrogen donor: (1) the activation energy for the hexagonal site was 0.056 eV and 0.093 eV corresponding to doping concentrations of 3.33 x 10 (exp 17) cm(exp -3) and 1.6 x 10(exp 18) cm(exp -3) and (2) the activation energy for the cubic site was 0.113 and 0.126 eV corresponding to doping concentrations of 4.2 x 10(exp 17) cm(exp -3) and 5.4 x 10(exp 18) cm(exp -3).

Determination of denudation rates by the measurement of meteoric 10Be in Guadiana river sediment samples (Spain) by low-energy AMS.

PubMed

Padilla, S; López-Gutiérrez, J M; Sampath, D M R; Boski, T; Nieto, J M; García-León, M

2018-09-01

The concentration of meteoric 10 Be in estuarine sediment samples has been measured by Spanish Accelerator for Radionuclides Analysis (SARA) at CNA and subsequently used to assess the denudation rate in Guadiana river basin together with the sediment budget method, on both sides of the frontier between Spain and Portugal. The two methods yielded coincident results. The estimation by the 10 Be method gave the denudation rate of (0.76 ± 0.10) × 10 -2  cm/y. After correcting for an approximate 80% attenuation of the sediment discharge into the ocean, caused by the river dams, the sediment budget method yielded the rate of (0.77 ± 0.17) × 10 -2  cm/y. Copyright © 2018 Elsevier Ltd. All rights reserved.

SU-F-T-550: Radiochromic Plastic Thin Sheet Dosimeter: Initial Performance

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jordan, K; Adamovics, J

Purpose: Thin sheets, of a high sensitivity formulation of radiochromic dosimeter, Presage were prepared and evaluated for optical readout. Methods: Sheets of radiochromic polyurethane, 12 cm long, 10 cm wide and 0.2 cm thick were prepared with leuco crystal violet as the reporter molecule. Sample transmission was evaluated at a wavelength of 590 nm with in-house constructed instruments: optical cone beam laser CT scanner, fixed and scanning spot densitometers. Sample sequential irradiations to a total dose of 40 Gy were conducted with a modified, Theratron 60, cobalt radiotherapy machine at dose rates of 1 or 0.25 Gy per minute. Exposuremore » to ambient and readout light was minimized to limit background photochromic signals. Samples were stored at 4°C. Optical activity was assessed from linearly polarized transmission images. Comparison sensitivity measurements with EBT3 film were conducted. Results: Samples were transparent, smooth and pale purple before irradiation. Radiochromic reaction was completed in less than 5 minutes. A linear dose response with a sensitivity of 0.5 cm-1Gy-1 was observed. Micrometer measurements found sheet thickness variations up to 20%. Uniform dose, 2 Gy attenuation images, correlated with local sheet thicknesses. Comparable measurements with EBT3 film were 3 times more sensitive at 1 Gy but above 15 Gy, EBT3 film had lower sensitivity than 0.2 cm thick Presage sheet dosimeter due to its non-linear response. Conclusion: Dose sensitivity provided a 10% decrease in transmission for a 1 Gy dose. Improvements in mold design are expected to allow production of sheets with less than 5% variation in thickness. Above, 10 Gy, Presage sheet dosimeter performance expected to exceed EBT3 film based on linearity, sensitivity, transparency and smoothness of samples. J Adamovics is owner of Heuris Inc.« less

Evaluation of a New Environmental Sampling Protocol for Detection of Human Norovirus on Inanimate Surfaces

PubMed Central

Lee, David; Treffiletti, Aimee; Hrsak, Mario; Shugart, Jill; Vinjé, Jan

2015-01-01

Inanimate surfaces are regarded as key vehicles for the spread of human norovirus during outbreaks. ISO method 15216 involves the use of cotton swabs for environmental sampling from food surfaces and fomites for the detection of norovirus genogroup I (GI) and GII. We evaluated the effects of the virus drying time (1, 8, 24, or 48 h), swab material (cotton, polyester, rayon, macrofoam, or an antistatic wipe), surface (stainless steel or a toilet seat), and area of the swabbed surface (25.8 cm2 to 645.0 cm2) on the recovery of human norovirus. Macrofoam swabs produced the highest rate of recovery of norovirus from surfaces as large as 645 cm2. The rates of recovery ranged from 2.2 to 36.0% for virus seeded on stainless-steel coupons (645.0 cm2) to 1.2 to 33.6% for toilet seat surfaces (700 cm2), with detection limits of 3.5 log10 and 4.0 log10 RNA copies. We used macrofoam swabs to collect environmental samples from several case cabins and common areas of a cruise ship where passengers had reported viral gastroenteritis symptoms. Seventeen (18.5%) of 92 samples tested positive for norovirus GII, and 4 samples could be sequenced and had identical GII.1 sequences. The viral loads of the swab samples from the cabins of the sick passengers ranged from 80 to 31,217 RNA copies, compared with 16 to 113 RNA copies for swab samples from public spaces. In conclusion, our swab protocol for norovirus may be a useful tool for outbreak investigations when no clinical samples are available to confirm the etiology. PMID:26116675

Radiation-Induced Changes in Quartz, A Mineral Analog of Nuclear Power Plant Concrete Aggregates.

PubMed

Silva, Chinthaka M; Rosseel, Thomas M; Kirkegaard, Marie C

2018-03-19

Quartz single-crystal samples consisting of α-quartz crystal structure were neutron irradiated to fluences of 5 × 10 18 , 4 × 10 19 , and 2 × 10 20 n/cm 2 (E > 0.1 MeV) at two temperatures (52 and 95 °C). The changes in the α-quartz phase as a function of these two conditions (temperature and fluence) were studied using X-ray powder diffraction (XRD), Raman spectroscopy, and transmission electron microscopy (TEM), and the results acquired using these complementary techniques are presented in a single place for the first time. XRD studies showed that the lattice parameters of α-quartz increased with increasing neutron flux. The lattice growth was larger for the samples that were neutron irradiated at 52 °C than at 95 °C. Moreover, an amorphous content was determined in the quartz samples neutron irradiated at 4 × 10 19 n/cm 2 , with the greater amount being in the 52 °C irradiated sample. Complete amorphization of quartz was observed at a fluence of 2 × 10 20 n/cm 2 (E > 0.1 MeV) using XRD and confirmed by TEM characterization and Raman spectroscopic studies. The cause for α-quartz lattice expansion and sample amorphization was also explored using XRD and Raman spectroscopic studies.

Changes in Soil Carbon Following Afforestation

DOE Data Explorer

Paul, K. I. [Commonwealth Scientific and Industrial Research Organization (CSIRO), Kingston ACT (Australia); Polglase, P. J. [Commonwealth Scientific and Industrial Research Organization (CSIRO), Kingston ACT (Australia; Nyakuengama, J. G. [Commonwealth Scientific and Industrial Research Organization (CSIRO), Kingston ACT (Australia); Khanna, P. K. [Commonwealth Scientific and Industrial Research Organization (CSIRO), Kingston ACT (Australia)

2003-01-01

Quantifying changes in soil C may be an important consideration under large-scale afforestation or reforestation. We reviewed global data on changes in soil C following afforestation, available from 43 published or unpublished studies, encompassing 204 sites. Data were highly variable, with soil C either increasing or decreasing, particularly in young (<10-y) forest stands. Because studies varied in the number of years since forest establishment and the initial soil C content, we calculated change in soil C as a weighted average (i.e. sum of C change divided by sum of years since forest establishment) relative to the soil C content under previous agricultural systems at <10 cm, >10 cm and <30 cm sampling depths. On average, soil C in the <10 cm (or <30 cm) layers generally decreased by 3.46% y^–1 (or 0.63% y^–1) relative to the initial soil C content during the first five years of afforestation, followed by a decrease in the rate of decline and eventually recovery to C contents found in agricultural soils at about age 30. In plantations older than 30 years, C content was similar to that under the previous agricultural systems within the surface 10 cm of soil, yet at other sampling depths, soil C had increased by between 0.50 and 0.86% y^–1. Amounts of C lost or gained by soil are generally small compared with accumulation of C in tree biomass.

Helium measurements of pore fluids obtained from the San Andreas Fault Observatory at Depth (SAFOD, USA) drill cores

NASA Astrophysics Data System (ADS)

Ali, S.; Stute, M.; Torgersen, T.; Winckler, G.; Kennedy, B. M.

2011-02-01

4He accumulated in fluids is a well established geochemical tracer used to study crustal fluid dynamics. Direct fluid samples are not always collectable; therefore, a method to extract rare gases from matrix fluids of whole rocks by diffusion has been adapted. Helium was measured on matrix fluids extracted from sandstones and mudstones recovered during the San Andreas Fault Observatory at Depth (SAFOD) drilling in California, USA. Samples were typically collected as subcores or from drillcore fragments. Helium concentration and isotope ratios were measured 4-6 times on each sample, and indicate a bulk 4He diffusion coefficient of 3.5 ± 1.3 × 10-8 cm2 s-1 at 21°C, compared to previously published diffusion coefficients of 1.2 × 10-18 cm2 s-1 (21°C) to 3.0 × 10-15 cm2 s-1 (150°C) in the sands and clays. Correcting the diffusion coefficient of 4Hewater for matrix porosity (˜3%) and tortuosity (˜6-13) produces effective diffusion coefficients of 1 × 10-8 cm2 s-1 (21°C) and 1 × 10-7 (120°C), effectively isolating pore fluid 4He from the 4He contained in the rock matrix. Model calculations indicate that <6% of helium initially dissolved in pore fluids was lost during the sampling process. Complete and quantitative extraction of the pore fluids provide minimum in situ porosity values for sandstones 2.8 ± 0.4% (SD, n = 4) and mudstones 3.1 ± 0.8% (SD, n = 4).

Au Colloids Formed by Ion Implantation in Muscovite Mica Studied by Vibrational and Electronic Spectroscopes and Atomic Force Microscopy

NASA Technical Reports Server (NTRS)

Tung, Y. S.; Henderson, D. O.; Mu, R.; Ueda, A.; Collins, W. E.; White, C. W.; Zuhr, R. A.; Zhu, Jane G.

1997-01-01

Au was implanted into the (001) surface of Muscovite mica at an energy of 1.1 MeV and at doses of 1, 3, 6, and 10 x 10(exp 16) ions/cu cm. Optical spectra of the as-implanted samples revealed a peak at 2.28 eV (545 nm) which is attributed to the surface plasmon absorption of Au colloids. The infrared reflectance measurements show a decreasing reflectivity with increasing ion dose in the Si-O stretching region (900-1200 /cm). A new peak observed at 967 /cm increases with the ion dose and is assigned to an Si-O dangling bond. Atomic force microscopy images of freshly cleaved samples implanted with 6 and 10 x 10(exp 16) ions/sq cm indicated metal colloids with diameters between 0.9- 1.5 nm. AFM images of the annealed samples showed irregularly shaped structures with a topology that results from the fusion of smaller colloids.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ogedengbe, O. S.; Swartz, C. H.; Jayathilaka, P. A. R. D.

Here, iodine-doped CdTe and Cd 1-xMg xTe layers were grown by molecular beam epitaxy. Secondary ion mass spectrometry characterization was used to measure dopant concentration, while Hall measurement was used for determining carrier concentration. Photoluminescence intensity and time-resolved photoluminescence techniques were used for optical characterization. Maximum n-type carrier concentrations of 7.4 x 10 18 cm -3 for CdTe and 3 x 10 17 cm -3 for Cd 0.65Mg 0.35Te were achieved. Studies suggest that electrically active doping with iodine is limited with dopant concentration much above these values. Dopant activation of about 80% was observed in most of the CdTemore » samples. The estimated activation energy is about 6 meV for CdTe and the value for Cd 0.65Mg 0.35Te is about 58 meV. Iodine-doped samples exhibit long lifetimes with no evidence of photoluminescence degradation with doping as high as 2 x 10 18 cm -3, while indium shows substantial non-radiative recombination at carrier concentrations above 5 x 10 16 cm -3. Iodine was shown to be thermally stable in CdTe at temperatures up to 600 °C. Results suggest iodine may be a preferred n-type dopant compared to indium in achieving heavily doped n-type CdTe.« less

Measurement and Modeling of Water-Vapor Diffusion in Elastomers with Impact in Humidity and Vacuum Measurements

NASA Astrophysics Data System (ADS)

Šetina, Janez; Sefa, Makfir; Erjavec, Bojan; Hudoklin, Domen

2013-03-01

The dynamics of water-vapor dissolution in Viton O-rings is measured with a gravimetric method using a precise mass comparator. A sample gasket was degassed in high vacuum for a sufficiently long period to remove more than 99 % of the dissolved water vapor. After that, it was exposed to the ambient atmosphere with a controlled temperature, and relative humidity and water-vapor uptake curves were measured gravimetrically with a precise balance. The dynamics of a water-vapor release into vacuum from another sample that was previously saturated with water vapor at room temperature was determined. The sample was placed in a vacuum outgassing rate measurement apparatus. The time dependence of the evolved water vapor was calculated by integrating the measured outgassing rate. The physical process of water absorption can be described by the diffusion equation. The geometry of the samples required solving the diffusion equation in cylindrical coordinates. This was done numerically using a finite-difference method. As a result of the modeling, room temperature values of the diffusion constant D, the solubility s, and the permeability K = D× s of water vapor in the sample material (Viton A-401C) were obtained. For sample 1, we obtained D = 8.0 × 10 ^{-8} cm2 {\\cdot } s^{-1} and s = 6.5 × 10^{-7} g {\\cdot } cm^-3 Pa^{-1}, while for sample 2, D = 3.0 × 10^{-7} cm2 s^{-1} and s = 3.5 × 10^{-7} g {\\cdot } cm^{-3} {\\cdot } Pa^{-1}.

SU-G-IeP3-07: High-Resolution, High-Sensitivity Imaging and Quantification of Intratumoral Distributions of Gold Nanoparticles Using a Benchtop L-Shell XRF Imaging System

DOE Office of Scientific and Technical Information (OSTI.GOV)

Manohar, N; Diagaradjane, P; Krishnan, S

2016-06-15

Purpose: To demonstrate the ability to perform high-resolution imaging and quantification of sparse distributions of gold nanoparticles (GNPs) within ex vivo tumor samples using a highly-sensitive benchtop L-shell x-ray fluorescence (XRF) imaging system. Methods: An optimized L-shell XRF imaging system was assembled using a tungsten-target x-ray source (operated at 62 kVp and 45 mA). The x-rays were filtered (copper: 0.08 mm & aluminum: 0.04 mm) and collimated (lead: 5 cm thickness, 3 cm aperture diameter) into a cone-beam in order to irradiate small samples or objects. A collimated (stainless steel: 4 cm thickness, 2 mm aperture diameter) silicon drift detector,more » capable of 2D translation, was placed at 90° with respect to the beam to acquire XRF/scatter spectra from regions of interest. Spectral processing involved extracting XRF signal from background, followed by attenuation correction using a Compton scatter-based normalization algorithm. Calibration phantoms with water/GNPs (0 and 0.00001–10 mg/cm{sup 3}) were used to determine the detection limit of the system at a 10-second acquisition time. The system was then used to map the distribution of GNPs within a 12×11×2 mm{sup 3} slice excised from the center of a GNP-loaded ex vivo murine tumor sample; a total of 110 voxels (2.65×10{sup −3} cm{sup 3}) were imaged with 1.3-mm spatial resolution. Results: The detection limit of the current cone-beam benchtop L-shell XRF system was 0.003 mg/cm{sup 3} (3 ppm). Intratumoral GNP concentrations ranging from 0.003 mg/cm{sup 3} (3 ppm) to a maximum of 0.055 mg/cm{sup 3} (55 ppm) and average of 0.0093 mg/cm{sup 3} (9.3 ppm) were imaged successfully within the ex vivo tumor slice. Conclusion: The developed cone-beam benchtop L-shell XRF imaging system can immediately be used for imaging of ex vivo tumor samples containing low concentrations of GNPs. With minor finetuning/optimization, the system can be directly adapted for performing routine preclinical in vivo imaging tasks. Supported by NIH/NCI grant R01CA155446 This investigation was supported by NIH/NCI grant R01CA155446.« less

Laser Annealing of Ion Implanted HgCdTe.

DTIC Science & Technology

1984-10-22

are /A 󈧳e10 4cm 2V- sec- and .(p) OA 103m mV - sec respectively. The above observations all lead to the conclusion that the donors in as-implanted...conductance. ". 5 Measured Hall Constante Hall Mobility Conductivuty Parameters type 2. Cb- (c2 v- - RH (cm.C ) Ac.v* ) Sample ....- 2 3 -1 -1A RH ...4.29.10 U=1.03.103 c(l -)- x=0.28 P ( 3 16 2.4 unimplanted ,,c -2-.l A RH .3.08"l0Z " .sYn-1 ) . Boron Implantation n n (cm a 16s. 4 48 ൒ U.12-10 1S

Fabrication of 5 at.%Yb:(La0.1Y0.9)2O3 transparent ceramics by chemical precipitation and vacuum sintering

NASA Astrophysics Data System (ADS)

Li, Shanshan; Zhu, Xingwen; Li, Jiang; Yavetskiy, Roman; Ivanov, Maxim; Liu, Binglong; Liu, Wenbin; Pan, Yubai

2017-09-01

Yttria (Y2O3) nanopowders were synthesized by a normal precipitation method using (NH4)2SO4 as dispersing agent. Pure Y2O3 powders without any other phase can be achieved by calcining the precursor at 600 °C for 4 h. The precursor and Y2O3 powders were characterized by TG-DTA, XRD, SEM and BET. In this work, 5 at.%Yb:(La0.1Y1.9)2O3 transparent ceramics were made by vacuum sintering at 1650 °C for 10 h. The in-line transmittance of the 5 at.%Yb:(La0.1Y0.9)2O3 ceramics is 81.3% at the wavelength of 1031 nm. The absorption cross-sections of the sample are calculated to be 1.20 × 10-20 cm2, 5.74 × 10-21 cm2 and 4.18 × 10-21 cm2 at 976, 951 and 906 nm, respectively. The emission cross-sections of the emission peak located at around 1031 and 1073 nm are 1.13 × 10-20 and 0.42 × 10-20 cm2, respectively.

Characterization of Hybrid Ferroelectric/HTS Thin Films for Tunable Microwave Components

NASA Technical Reports Server (NTRS)

Winters, M. D.; Mueller, C. H.; Bhasin, K. B.; Miranda, F. A.

1996-01-01

Since the discovery of High-Temperature-Superconductors (HTS) in 1986, a diversity of HTS-based microwave components has been demonstrated. Because of their low conductor losses, HTS-based components are very attractive for integration into microwave circuits for space communication systems. Recent advancements have made deposition of ferroelectric thin films onto HTS thin films possible. Due to the sensitivity of the ferroelectric's dielectric constant (epsilon(sub r)) to an externally applied electric field (E), ferroelectric/superconducting structures could be used in the fabrication of low loss, tunable microwave components. In this paper, we report on our study of Ba(0.5)Sr(0.5)TiO3/YBa2Cu3O(7-delta) and Ba(0.08)Sr(0.92)TiO3/YBa2Cu3O(7-delta) ferroelectric/superconducting thin films on lanthanum aluminate (LaAlO3) substrates. For the (Ba:Sr, 0.50:0.50) epitaxial sample, a epsilon(sub r) of 425 and a loss tangent (tan delta) of 0.040 were measured at 298 K, 1.0 MHz, and zero applied E. For the same sample, a epsilon(sub r) of 360 and tan delta of 0.036 were obtained at 77 K, 1.0 MHz, and zero applied E. Variations in epsilon(sub r) from 180 to 360 were observed over an applied E range of 0V/cm less than or equal to E less than or equal to 5.62 x 10(exp 4) V/cm with little change in tan delta. However, the range of epsilon(sub r) variation for the polycrystalline (Ba:Sr, 0.08:0.92) sample over 0V/cm less than or equal to E less than or equal to 4.00 x 10(exp 4) V/cm was only 3.6 percent while tan delta increased markedly. These results indicate that a lack of epitaxy between the ferroelectric and superconducting layers decreases tuning and increases microwave losses.

Probing resistivity and doping concentration of semiconductors at the nanoscale using scanning microwave microscopy

NASA Astrophysics Data System (ADS)

Brinciotti, Enrico; Gramse, Georg; Hommel, Soeren; Schweinboeck, Thomas; Altes, Andreas; Fenner, Matthias A.; Smoliner, Juergen; Kasper, Manuel; Badino, Giorgio; Tuca, Silviu-Sorin; Kienberger, Ferry

2015-08-01

We present a new method to extract resistivity and doping concentration of semiconductor materials from Scanning Microwave Microscopy (SMM) S11 reflection measurements. Using a three error parameters de-embedding workflow, the S11 raw data are converted into calibrated capacitance and resistance images where no calibration sample is required. The SMM capacitance and resistance values were measured at 18 GHz and ranged from 0 to 100 aF and from 0 to 1 MΩ, respectively. A tip-sample analytical model that includes tip radius, microwave penetration skin depth, and semiconductor depletion layer width has been applied to extract resistivity and doping concentration from the calibrated SMM resistance. The method has been tested on two doped silicon samples and in both cases the resistivity and doping concentration are in quantitative agreement with the data-sheet values over a range of 10-3 Ω cm to 101 Ω cm, and 1014 atoms per cm3 to 1020 atoms per cm3, respectively. The measured dopant density values, with related uncertainties, are [1.1 +/- 0.6] × 1018 atoms per cm3, [2.2 +/- 0.4] × 1017 atoms per cm3, [4.5 +/- 0.2] × 1016 atoms per cm3, [4.5 +/- 1.3] × 1015 atoms per cm3, [4.5 +/- 1.7] × 1014 atoms per cm3. The method does not require sample treatment like cleavage and cross-sectioning, and high contact imaging forces are not necessary, thus it is easily applicable to various semiconductor and materials science investigations.

A simple procedure for estimating soil porosity

NASA Astrophysics Data System (ADS)

Emmet-Booth, Jeremy; Forristal, Dermot; Fenton, Owen; Holden, Nick

2016-04-01

Soil degradation from mismanagement is of international concern. Simple, accessible tools for rapidly assessing impacts of soil management are required. Soil structure is a key component of soil quality and porosity is a useful indicator of structure. We outline a version of a procedure described by Piwowarczyk et al. (2011) used to estimate porosity of samples taken during a soil quality survey of 38 sites across Ireland as part of the Government funded SQUARE (Soil Quality Assessment Research) project. This required intact core (r = 2.5 cm, H = 5cm) samples taken at 5-10 cm and 10-20 cm depth, to be covered with muslin cloth at one end and secured with a jubilee clip. Samples were saturated in sealable water tanks for ≈ 64 hours, then allowed to drain by gravity for 24 hours, at which point Field Capacity (F.C.) was assumed to have been reached, followed by oven drying with weight determined at each stage. This allowed the calculation of bulk density and the estimation of water content at saturation and following gravitational drainage, thus total and functional porosity. The assumption that F.C. was reached following 24 hours of gravitational drainage was based on the Soil Moisture Deficit model used in Ireland to predict when soils are potentially vulnerable to structural damage and used nationally as a management tool. Preliminary results indicate moderately strong, negative correlations between estimated total porosity at 5-10 cm and 10-20 cm depth (rs = -0.7, P < 0.01 in both cases) and soil quality scores of the Visual Evaluation of Soil Structure (VESS) method which was conducted at each survey site. Estimated functional porosity at 5-10 cm depth was found to moderately, negatively correlate with VESS scores (rs = - 0.5, P < 0.05). This simple procedure requires inexpensive equipment and appears useful in indicating porosity of a large quantity of samples taken at numerous sites or if done periodically, temporal changes in porosity at a field scale, indicating the impacts of soil management. Reference Piwowarczyk, A., Giuliani, G. & Holden, N.M. 2011. Can soil moisture deficit be used to forecast when soils are at high risk of damage owing to grazing animals? Soil Use and Management, 27, 255-263.

[Soil sandy desertification and salinization and their interrelationships in Yanghuang irrigated area of Hongsipu, Ningxia of northwest China].

PubMed

Yang, Xin-guo; Song, Nai-ping

2011-09-01

By the methods of controlled and typical sampling, this paper analyzed the texture, salinization characteristics, cation exchange capacity (CEC), and their correlations in the 0-40 cm soil profiles of corn land, medlar land, and non-utilized land in Yanghuang irrigated area of Hongsipu, Northwest China. Under controlled sampling, the salt content in the soil profiles was 0.69-1.30 g x kg(-1) (except in non-utilized land where the 0-10 cm soil salt content was up to 1.74 g x kg(-1)), with no obvious salinization. The sodium adsorption ratio and exchangeable sodium percentage in the 20-40 cm soil layer of medlar land were 12.18 and 14.1%, respectively, and the total content of clay and silt in the 0-40 cm soil profile of medlar land was up to 37.3% whereas that in the 0-20 cm soil layer of corn land was only 13.5%. In the 20-40 cm soil layer of corn land, the indices of sandy desertification and salinization had significant correlations under controlled sampling but no correlations under typical sampling, while the CEC and the sandy desertification and salinization indices had significant correlations under typical sampling. In different land use types in the study area, soil sandy desertification and salinization had complicated interrelationships, and CEC could be used as the indicator for the changes in soil environmental quality.

Radiation-Induced Changes in Quartz, A Mineral Analog of Nuclear Power Plant Concrete Aggregates

DOE Office of Scientific and Technical Information (OSTI.GOV)

Silva, Chinthaka M.; Rosseel, Thomas M.; Kirkegaard, Marie C.

Quartz single-crystal samples consisting of α-quartz crystal structure were neutron irradiated to fluences of 5 × 10 18, 4 × 10 19, and 2 × 10 20 n/cm 2 (E > 0.1 MeV) at two temperatures (52 and 95 °C). The changes in the α-quartz phase as a function of these two conditions (temperature and fluence) were studied using X-ray powder diffraction (XRD), Raman spectroscopy, and transmission electron microscopy (TEM), and the results acquired using these complementary techniques are presented in a single place for the first time. XRD studies showed that the lattice parameters of α-quartz increased with increasingmore » neutron flux. The lattice growth was larger for the samples that were neutron irradiated at 52 °C than at 95 °C. Moreover, an amorphous content was determined in the quartz samples neutron irradiated at 4 × 10 19 n/cm 2, with the greater amount being in the 52 °C irradiated sample. Complete amorphization of quartz was observed at a fluence of 2 × 10 20 n/cm 2 (E > 0.1 MeV) using XRD and confirmed by TEM characterization and Raman spectroscopic studies. In conclusion, the cause for α-quartz lattice expansion and sample amorphization was also explored using XRD and Raman spectroscopic studies.« less

Radiation-Induced Changes in Quartz, A Mineral Analog of Nuclear Power Plant Concrete Aggregates

DOE PAGES

Silva, Chinthaka M.; Rosseel, Thomas M.; Kirkegaard, Marie C.

2018-03-07

Quartz single-crystal samples consisting of α-quartz crystal structure were neutron irradiated to fluences of 5 × 10 18, 4 × 10 19, and 2 × 10 20 n/cm 2 (E > 0.1 MeV) at two temperatures (52 and 95 °C). The changes in the α-quartz phase as a function of these two conditions (temperature and fluence) were studied using X-ray powder diffraction (XRD), Raman spectroscopy, and transmission electron microscopy (TEM), and the results acquired using these complementary techniques are presented in a single place for the first time. XRD studies showed that the lattice parameters of α-quartz increased with increasingmore » neutron flux. The lattice growth was larger for the samples that were neutron irradiated at 52 °C than at 95 °C. Moreover, an amorphous content was determined in the quartz samples neutron irradiated at 4 × 10 19 n/cm 2, with the greater amount being in the 52 °C irradiated sample. Complete amorphization of quartz was observed at a fluence of 2 × 10 20 n/cm 2 (E > 0.1 MeV) using XRD and confirmed by TEM characterization and Raman spectroscopic studies. In conclusion, the cause for α-quartz lattice expansion and sample amorphization was also explored using XRD and Raman spectroscopic studies.« less

Fine woody fuel particle diameters for improved planar intersect fuel loading estimates in Southern Rocky Mountain ponderosa pine forests

Treesearch

Emma Vakili; Chad M. Hoffman; Robert E. Keane

2016-01-01

Fuel loading estimates from planar intersect sampling protocols for fine dead down woody surface fuels require an approximation of the mean squared diameter (d2) of 1-h (0-0.63 cm), 10-h (0.63-2.54 cm), and 100-h (2.54-7.62 cm) timelag size classes. The objective of this study is to determine d2 in ponderosa pine (Pinus ponderosa) forests of New Mexico and Colorado,...

[Transportation and risk assessment of heavy metal pollution in water-soil from the Riparian Zone of Daye Lake, China].

PubMed

Zhang, Jia-quan; Li, Xiu; Zhang, Quan-fa; Li, Qiong; Xiao, Wen-sheng; Wang, Yong-kui; Zhang, Jian-chun; Gai, Xi-guang

2015-01-01

Each 20 water samples and soil samples (0-10 cm, 10-20 cm) were collected from the riparian zone of Daye Lake in dry season during March 2013. Heavy metals (Cu, Ph, Cd, Zn) have been detected by flame atomic absorption spectrometric (FAAS). The results showed that the average concentrations of Cu, Pb, Cd, Zn in the water were 7.14, 25.94, 15.72 and 37.58 microg x L(-1), respectively. The concentration of Cu was higher than the five degree of the surface water environment quality standard. The average concentrations of Cu, Pb, Cd, Zn in soil(0-10 cm) were 108.38, 53.92, 3.55, 139.26 mg x kg(-1) in soil (10-20 cm) were 93.00, 51.72, 2.08, 171.00 mg x kg(-1), respectively. The Cd concentrations were higher than the three grade value of the national soil environment quality standard. The transportation of Pb from soil to water was relatively stable, and Zn was greatly influenced by soil property and the surrounding environment from soil to water. The transformation of heavy metal in west riparian zone was higher than that of east riparian zone. The potential environmental risk was relatively high. Cu, Pb, Cd, Zn were dominated by residue fraction of the modified BCR sequential extraction method. The overall migration order of heavy metal element was: Pb > Cu > Cd > Zn. There were stronger transformation and higher environmental pollution risk of Cu, Pb. The index of assessment and potential ecological risk coefficient indicated that heavy metal pollution in soil (0-10 cm) was higher than the soil (10-20 cm), Cd was particularly serious.

Impact of Mg-ion implantation with various fluence ranges on optical properties of n-type GaN

NASA Astrophysics Data System (ADS)

Tsuge, Hirofumi; Ikeda, Kiyoji; Kato, Shigeki; Nishimura, Tomoaki; Nakamura, Tohru; Kuriyama, Kazuo; Mishima, Tomoyoshi

2017-10-01

Optical characteristics of Mg-ion implanted GaN layers with various fluence ranges were evaluated. Mg ion implantation was performed twice at energies of 30 and 60 keV on n-GaN layers. The first implantation at 30 keV was performed with three different fluence ranges of 1.0 × 1014, 1.0 × 1015 and 5.0 × 1015 cm-2. The second implantation at an energy of 60 keV was performed with a fluence of 6.5 × 1013 cm-2. After implantation, samples were annealed at 1250 °C for 1 min under N2 atmosphere. Photoluminescence (PL) spectrum of the GaN layer with the Mg ion implantation at the fluence range of 1.0 × 1014 cm-2 at 30 keV was similar to the one of Mg-doped p-GaN layers grown by MOVPE (Metal-Organic Vapor Phase Epitaxy) on free-standing GaN substrates and those at the fluence ranges over 1.0 × 1015 cm-2 were largely degraded.

SYNTHESIS AND Zn2+ ION CONDUCTION OF A PEROVSKITE (La, Zn)TiO3

NASA Astrophysics Data System (ADS)

Mashiko, W.; Katsumata, T.; Inaguma, Y.

(La,Zn)TiO3 was synthesized by an ion exchange method using ZnCl2 molten salt. By a powder X-ray diffraction, it was confirmed that perovskite structure was retained after ion exchange. The composition of ion exchanged sample was determined to be La0.55(6)Li0.064(4)Zn0.13(1)Ti1.0(1)O2.97 by ICP analysis, and the homogeneous distribution of Zn in this sample was confirmed by the scanning electron microscope (SEM). The bulk and total conductivity of the sample at the room temperature was measured to be 6.9 × 10-7 S·cm-1, 1.7 × 10-7 S·cm-1, respectively. The mobile species was confirmed to be Zn2+ by the electrolysis at 500°C.

A 10-day vacancy period after cleaning and disinfection has no effect on the bacterial load in pig nursery units.

PubMed

Luyckx, K; Millet, S; Van Weyenberg, S; Herman, L; Heyndrickx, M; Dewulf, J; De Reu, K

2016-10-19

Biosecurity measures such as cleaning, disinfection and a vacancy period between production cycles on pig farms are essential to prevent disease outbreaks. No studies have tested the effect of a longer vacancy period on bacterial load in nursery units. The present study evaluated the effect of a 10-day vacancy period in pig nursery units on total aerobic flora, Enterococcus spp., Escherichia coli, faecal coliforms and methicillin resistant Staphylococcus aureus (MRSA). Three vacancy periods of 10 days were monitored, each time applied in 3 units. The microbiological load was measured before disinfection and at 1, 4, 7 and 10 days after disinfection. No significant decrease or increase in E. coli, faecal coliforms, MRSA and Enterococcus spp. was noticed. Total aerobic flora counts were the lowest on day 4 after disinfection (i.e. 4.07 log CFU/625 cm 2 ) (P < 0.05), but the difference with other sampling moments was limited (i.e. 0.6 log CFU/625 cm 2 ) and therefore negligible. Furthermore, this observation on day 4 was not confirmed for the other microbiological parameters. After disinfection, drinking nipples were still mostly contaminated with total aerobic flora (i.e. 5.32 log CFU/625 cm 2 ) and Enterococcus spp. (i.e. 95 % of the samples were positive) (P < 0.01); the feeding troughs were the cleanest location (total aerobic flora: 3.53 log CFU/625 cm 2 and Enterococcus spp.: 50 % positive samples) (P < 0.01). This study indicates that prolonging the vacancy period in nursery units to 10 days after disinfection with no extra biosecurity measures has no impact on the environmental load of total aerobic flora, E. coli, faecal coliforms, MRSA and Enterococcus spp..

Iodine Doping of CdTe and CdMgTe for Photovoltaic Applications

DOE PAGES

Ogedengbe, O. S.; Swartz, C. H.; Jayathilaka, P. A. R. D.; ...

2017-06-06

Here, iodine-doped CdTe and Cd 1-xMg xTe layers were grown by molecular beam epitaxy. Secondary ion mass spectrometry characterization was used to measure dopant concentration, while Hall measurement was used for determining carrier concentration. Photoluminescence intensity and time-resolved photoluminescence techniques were used for optical characterization. Maximum n-type carrier concentrations of 7.4 x 10 18 cm -3 for CdTe and 3 x 10 17 cm -3 for Cd 0.65Mg 0.35Te were achieved. Studies suggest that electrically active doping with iodine is limited with dopant concentration much above these values. Dopant activation of about 80% was observed in most of the CdTemore » samples. The estimated activation energy is about 6 meV for CdTe and the value for Cd 0.65Mg 0.35Te is about 58 meV. Iodine-doped samples exhibit long lifetimes with no evidence of photoluminescence degradation with doping as high as 2 x 10 18 cm -3, while indium shows substantial non-radiative recombination at carrier concentrations above 5 x 10 16 cm -3. Iodine was shown to be thermally stable in CdTe at temperatures up to 600 °C. Results suggest iodine may be a preferred n-type dopant compared to indium in achieving heavily doped n-type CdTe.« less

A mini drivepoint sampler for measuring pore water solute concentrations in the hyporheic zone of sand-bottom streams

USGS Publications Warehouse

Duff, J.H.; Murphy, F.; Fuller, C.C.; Triska, F.J.

1998-01-01

A new method for collecting pore-water samples in sand and gravel streambeds is presented. We developed a mini drivepoint solution sampling (MINIPOINT) technique to collect pore-water samples at 2.5-cm vertical resolution. The sampler consisted of six small-diameter stainless steel drivepoints arranged in a 10-cm-diameter circular array. In a simple procedure, the sampler was installed in the streambed to preset drivepoint depths of 2.5, 5.0, 7.5, 10.0, 12.5, and 15.0 cm. Sampler performance was evaluated in the Shingobee River, Minnesota, and Pinal Creek, Arizona, by measuring the vertical gradient of chloride concentration in pore water beneath the streambed that was established by the uninterrupted injection to the stream for 3 d. Pore-water samples were withdrawn from all drivepoints simultaneously. In the first evaluation, the vertical chloride gradient was unchanged at withdrawal rates between 0.3 and 4.0 ml min-1 but was disturbed at higher rates. In the second evaluation, up to 70 ml of pore water was withdrawn from each drivepoint at a withdrawal rate of 2.5 ml min-1 without disturbing the vertical chloride gradient. Background concentrations of other solutes were also determined with MINIPOINT sampling. Steep vertical gradients were present for biologically reactive solutes such as DO, NH4/+, NO3/-, and dissolved organic C in the top 20 cm of the streambed. These detailed solute profiles in the hyporheic zone could not have been determined without a method for close interval vertical sampling that does not disturb natural hydrologic mixing between stream water and groundwater.

Anaerobic Oxidation of Methane in Sediments of Two Boreal Lakes

NASA Astrophysics Data System (ADS)

Tiirola, M. A.; Rissanen, A. J.; Karvinen, A.; Nykänen, H.; Mpamah, P.; Peura, S.; Kankaala, P.

2014-12-01

In this study, potential for Anaerobic oxidation of methane (AOM) coupled with metal reduction was studied in boreal lake sediments. Slurries of sediment samples collected from two sites in southeastern Finland, i.e. from Lake Orivesi, Heposelkä, an vegetated littoral site, dominated by Phragmites australis (Sample Sa, sediment layer 0 - 25 cm) and from the profundal zone of a mesotrophic Lake Ätäskö (Aa, 0 - 10 cm; Ab, 10 - 30 cm; Ac, 90 - 130 cm), were incubated in laboratory in anaerobic conditions at in situ temperatures for up to 5 months. The samples were amended either 1) with 13CH4, 2) 13CH4 + manganese(IV) oxide (MnO2) or 3) 13CH4 + iron(III) hydroxide (Fe(OH)3), and the processes were measured by following the 13C transfer to the carbon dioxide (CO2) pool and by concentration measurements of CH4 and CO2. Changes in microbial communities were studied from DNA extracted from sediment samples before and after incubation period by next-generation sequencing (Ion Torrent) of polymerase chain reaction (PCR) - amplified bacterial and archaeal 16S rRNA and methyl coenzyme-M reductase gene (mcrA) amplicons. AOM took place in every sample except in deepest sample (Ac) with potential rates up to 2.1 nmol CH4 d-1 g-1wetsedim (~2 nmol d-1 cm-3) which are considerably lower than previously reported metal-driven AOM in marine sediments (10-40 nmol d-1 cm-3) but within a range of NO3- -driven AOM in an oligotrophic lake (0.6-3.6 nmol d-1 cm-3). AOM took place without metal additions but addition of Mn4+ increased the potential rates and this increase was especially high in 10-30 cm layer (Ab) of the profundal site (5-fold increase). The structure of the bacterial and archaeal communities changed considerably during incubation. Communities incubated with Mn4+ were especially different from those incubated with Fe3+ or without metals which were more similar with each other. Surprisingly, anaerobic methanotrophic archaea detected, ANME-2D and AOM-associated archaea (AAA), were almost absent in the littoral site and constituted only up to 3.5% and 5% of archaeal 16S rRNA and mcrA gene sequences, respectively, in the profundal site. Mn4+ induced an increase in the abundance of ANME-2D and AAA in the profundal site which indicates that they are involved in Mn4+ - dependent AOM.

Effects of tillage on the Fe oxides activation in soil

NASA Astrophysics Data System (ADS)

Chi, Guangyu; Chen, Xin; Shi, Yi; Wang, Jun; Zheng, Taihui

2009-07-01

Since mid-1950s, the wetland ecosystems in Sanjiang Plain of Northeast China have been experiencing greater changes in land use, which had negative effects on the soil environments. This study assessed the effects of soil tillage on the activation of soil Fe in the region. The test ecosystems included natural wetland, paddy field and upland field converted from wetland. Soil samples at the depths of 0-10 cm, 10-20 cm, 20-30 cm, 30-40 cm, 40-60 cm, 60-90 cm and 90-120 cm were collected from each of the ecosystems for the analysis of vertical distribution of soil pH, organic carbon, chelate Fe oxides and Fe(II). The results showed that the conversion of wetland into paddy field and upland field induced a decrease of organic carbon content in 0-10 cm soil layer by 61.8% (P <0.05) and 70.0% (P < 0.05), respectively. The correlations among iron forms and soil organic carbon showed that chelate Fe oxides and Fe(II) was correlated positively with soil organic carbon and chelate ratio had a more positive relationship with organic carbon than chelate Fe oxides and Fe(II). The results of chelate Fe oxides, Fe(II) and chelate ratio of Fe suggested that reclamation could prevent the Fe activation and organic matter is credited for having an important influence on the process of Fe activation.

Microbiological evaluation of groups of beef carcasses: heifers and steers.

PubMed Central

Jericho, K W; Bradley, J A; Kozub, G C

1994-01-01

Numbers of mesophilic bacteria were estimated on carcasses of 25 heifers and 25 steers of beef breeds in a modern, high-line-speed abattoir. One side of each carcass from each sex was sampled at the end of the kill-floor, before the carcass wash, on each of 25 visits. Two adjacent excision samples (5 x 5 x 0.5 cm) were taken from each of ten sites and processed for automatic enumeration of aerobic bacteria on hydrophobic grid membrane filters. The effects of sex and carcass weight on bacterial counts were examined. Groups of carcasses were examined to determine the sample size required for future assessments of kill-floor hygiene. The log10 of the most probable number of growth units (MPNGU)/cm2 did not differ significantly between heifers and steers (average over the ten sites of 2.2) and there was no effect of carcass weight on bacterial counts for nine of the ten sites. There were, however, highly significant (p < 0.001) differences in the counts between sites and the counts from the ten sites clustered into five homogenous groups. The between-carcass component of variation at a site was generally larger than the within-carcass component. We conclude that, to estimate the mean log10 MPNGU/cm2 at a site to within +/- 0.5 units, future group-carcass evaluations require about 200 samples from 10 (two adjacent samples/site) or 20 carcasses (one sample/site). PMID:7954120

Exposure to airborne asbestos in thermal power plants in Mongolia

PubMed Central

Damiran, Naransukh; Silbergeld, Ellen K; Frank, Arthur L; Lkhasuren, Oyuntogos; Ochir, Chimedsuren; Breysse, Patrick N

2015-01-01

Background: Coal-fired thermal power plants (TPPs) in Mongolia use various types of asbestos-containing materials (ACMs) in thermal insulation of piping systems, furnaces, and other products. Objective: To investigate the occupational exposure of insulation workers to airborne asbestos in Mongolian power plants. Methods: Forty-seven air samples were collected from four power plants in Mongolia during the progress of insulation work. The samples were analyzed by phase contrast microscopy (PCM) and transmission electron microscopy (TEM). Results: The average phase contrast microscopy equivalent (PCME) asbestos fiber concentration was 0.93 f/cm3. Sixteen of the 41 personal and one of the area samples exceeded the United States Occupational Safety and Health Administration (US OSHA) short-term exposure limit of 1.0 f/cm3. If it is assumed that the short-term samples collected are representative of full-shift exposure, then the exposures are approximately 10 times higher than the US OSHA 8-hour permissible exposure limit of 0.1 f/cm3. Conclusion: Power plant insulation workers are exposed to airborne asbestos at concentrations that exceed the US OSHA Permissible Exposure Limit. Action to mitigate the risks should be taken in Mongolia. PMID:25730489

Hysteresis in Lanthanide Zirconium Oxides Observed Using a Pulse CV Technique and including the Effect of High Temperature Annealing.

PubMed

Lu, Qifeng; Zhao, Chun; Mu, Yifei; Zhao, Ce Zhou; Taylor, Stephen; Chalker, Paul R

2015-07-29

A powerful characterization technique, pulse capacitance-voltage (CV) technique, was used to investigate oxide traps before and after annealing for lanthanide zirconium oxide thin films deposited on n-type Si (111) substrates at 300 °C by liquid injection Atomic Layer Deposition (ALD). The results indicated that: (1) more traps were observed compared to the conventional capacitance-voltage characterization method in LaZrO x ; (2) the time-dependent trapping/de-trapping was influenced by the edge time, width and peak-to-peak voltage of a gate voltage pulse. Post deposition annealing was performed at 700 °C, 800 °C and 900 °C in N₂ ambient for 15 s to the samples with 200 ALD cycles. The effect of the high temperature annealing on oxide traps and leakage current were subsequently explored. It showed that more traps were generated after annealing with the trap density increasing from 1.41 × 10 12 cm -2 for as-deposited sample to 4.55 × 10 12 cm -2 for the 800 °C annealed one. In addition, the leakage current density increase from about 10 - ⁶ A/cm² at V g = +0.5 V for the as-deposited sample to 10 -3 A/cm² at V g = +0.5 V for the 900 °C annealed one.

Transport properties of undoped and Br-doped PbTe sintered at high temperature and pressure> 4.0 GPa

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yongkwan, Dong; McGuire, Michael A; Malik, Abds-Sami

2009-01-01

The thermoelectric properties of nominally undoped PbTe and Br doped PbTe materials sintered at high-pressure and high-temperature (HPHT) have been studied. All samples show n-type semiconducting behavior with negative thermopower. For undoped PbTe, four different HPHT treatments were performed at pressures between 4.0 and 6.5 GPa. PbTe doped with Br at 0.5, 1.0, 2.0, 3.0 x 10{sup 19} cm{sup -3} was HPHT treated at 4.0 GPa and 1045 C. As the dopant concentration increases, the absolute thermopower decreases, thermal conductivity increases, and electrical resistivity decreases. At a nominal dopant concentration of 1.0 x 10{sup 19} cm{sup -3}, carrier mobility ofmore » 1165 cm{sup 2}/V s and dimensionless thermoelectric figure-of-merit, ZT, of around 0.27 at 300 K were obtained. These results demonstrate that HPHT post-processing is a viable and controllable way of tuning the thermoelectric properties of PbTe-based materials.« less

The NuSTAR  Extragalactic Surveys: X-Ray Spectroscopic Analysis of the Bright Hard-band Selected Sample

NASA Astrophysics Data System (ADS)

Zappacosta, L.; Comastri, A.; Civano, F.; Puccetti, S.; Fiore, F.; Aird, J.; Del Moro, A.; Lansbury, G. B.; Lanzuisi, G.; Goulding, A.; Mullaney, J. R.; Stern, D.; Ajello, M.; Alexander, D. M.; Ballantyne, D. R.; Bauer, F. E.; Brandt, W. N.; Chen, C.-T. J.; Farrah, D.; Harrison, F. A.; Gandhi, P.; Lanz, L.; Masini, A.; Marchesi, S.; Ricci, C.; Treister, E.

2018-02-01

We discuss the spectral analysis of a sample of 63 active galactic nuclei (AGN) detected above a limiting flux of S(8{--}24 {keV})=7× {10}-14 {erg} {{{s}}}-1 {{cm}}-2 in the multi-tiered NuSTAR extragalactic survey program. The sources span a redshift range z=0{--}2.1 (median < z> =0.58). The spectral analysis is performed over the broad 0.5–24 keV energy range, combining NuSTAR with Chandra and/or XMM-Newton data and employing empirical and physically motivated models. This constitutes the largest sample of AGN selected at > 10 {keV} to be homogeneously spectrally analyzed at these flux levels. We study the distribution of spectral parameters such as photon index, column density ({N}{{H}}), reflection parameter ({\\boldsymbol{R}}), and 10–40 keV luminosity ({L}{{X}}). Heavily obscured ({log}[{N}{{H}}/{{cm}}-2]≥slant 23) and Compton-thick (CT; {log}[{N}{{H}}/{{cm}}-2]≥slant 24) AGN constitute ∼25% (15–17 sources) and ∼2–3% (1–2 sources) of the sample, respectively. The observed {N}{{H}} distribution agrees fairly well with predictions of cosmic X-ray background population-synthesis models (CXBPSM). We estimate the intrinsic fraction of AGN as a function of {N}{{H}}, accounting for the bias against obscured AGN in a flux-selected sample. The fraction of CT AGN relative to {log}[{N}{{H}}/{{cm}}-2]=20{--}24 AGN is poorly constrained, formally in the range 2–56% (90% upper limit of 66%). We derived a fraction (f abs) of obscured AGN ({log}[{N}{{H}}/{{cm}}-2]=22{--}24) as a function of {L}{{X}} in agreement with CXBPSM and previous z< 1 X-ray determinations. Furthermore, f abs at z=0.1{--}0.5 and {log}({L}{{x}}/{erg} {{{s}}}-1)≈ 43.6{--}44.3 agrees with observational measurements/trends obtained over larger redshift intervals. We report a significant anti-correlation of R with {L}{{X}} (confirmed by our companion paper on stacked spectra) with considerable scatter around the median R values.

TU-H-CAMPUS-TeP2-04: Measurement of Stereotactic Output Factors with DNA Double-Strand Breaks

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cline, K; Obeidat, M; Stathakis, S

Purpose: Radiotherapy treatment is specified by radiation dose prescriptions, but biological DNA damage actually controls treatment effectiveness. It is impractical to directly measure dose in the clinic, so we measure quantities, such as collected charge, and calculate the relationship to dose. At small fields, such as those in stereotactic radiosurgery (SRS), charged-particle equilibrium (CPE) breaks down and the accuracy of the measurement for delivered dose decreases. By measuring DNA double-strand breaks (DSB) directly, we believe treatment accuracy could improve by providing a more meaningful measurement. Methods: A DNA dosimeter, consisting of magnetic streptavidin beads attached to 4 kilobase pair DNAmore » strands labeled with biotin and fluorescein amidite (FAM) on opposing ends, was suspended in phosphate-buffered saline (PBS). Twenty µL samples were placed in plastic micro-capillary tubes inside a water tank setup and irradiated with 10 cm, 3 cm, 1.25 cm, 0.75 cm, and 0.5 cm radiation field sizes, where the three smallest sizes were cones. After irradiation, the dosimeters were mechanically separated into beads (intact DNA) and supernatant (broken DNA/FAM) using a magnet. The fluorescence was read and the probability of DSB was calculated. This was used to calculate the output factor for an SRS beam and compared to that measured using a diode detector. Results: The output factors relative to a 10 cm field were 0.89±0.07, 0.76±0.08, 0.59±0.04, and 0.78±0.12 for the field sizes of 3 cm, 1.25 cm, 0.75 cm, and 0.5 cm, respectively. Some of the diode measurements do not fall within these uncertainties. Conclusion: This was the first attempt to measure output factors in a water tank with the DNA dosimeter. Although differences compared to the diode were observed, the uncertainty analysis ignored systematic errors. For future work, we will repeat this experiment to quantify and correct systematic errors, such as those caused by positional alignment and sample contamination. This work was funded in part by CPRIT (RP140105).« less

Investigation of structural, optical, magnetic and electrical properties of tungsten doped Nisbnd Zn nano-ferrites

NASA Astrophysics Data System (ADS)

Pathania, Abhilash; Bhardwaj, Sanjay; Thakur, Shyam Singh; Mattei, Jean-Luc; Queffelec, Patrick; Panina, Larissa V.; Thakur, Preeti; Thakur, Atul

2018-02-01

Tungsten substituted nickel-zinc ferrite nanoparticles with chemical composition of Ni0.5Zn0.5WxFe2-xO4 (x = 0.0, 0.2, 0.4, 0.6, 0.8 & 1.0) were successfully synthesized by a chemical co-precipitation method. The prepared ferrites were pre sintered at 850 °C and then annealed at 1000 °C in a muffle furnace for 3 h each. This sintered powder was inspected by X-ray diffraction (XRD), transmission electron microscopy (TEM), Fourier transform infrared spectroscopy (FTIR), and vibrating sample magnetometer (VSM) to study the structural, optical, and magnetic properties. XRD measurement revealed the phase purity of all the nanoferrite samples with cubic spinel structure. The estimated crystallite size by X-ray line broadening is found in the range of 49-62 nm. FTIR spectra of all the samples have observed two prominent absorption bands in the range 400-700 cm-1 arising due to tetrahedral and octahedral stretching vibrations. Vibrating sample magnetometer experiments showed that the saturation magnetizations (MS) decreased with an increase in non-magnetic tungsten ion doping. The electrical resistivity of tungsten doped Nisbnd Zn nano ferrites were examined extensively as a function of temperature. With an increase in tungsten composition, resistivity was found to decrease from 2.2 × 105 Ω cm to 1.9 × 105 Ω cm which indicates the semiconducting behavior of the ferrite samples. The activation energy also decreased from 0.0264 to 0.0221 eV at x = 0.0 to x = 1.0. These low coercive field tungsten doped Nisbnd Zn ferrites are suitable for hyperthermia and sensor applications. These observations are explained in detail on the basis of various models and theories.

Conductivity and transport studies of plasticized chitosan-based proton conducting biopolymer electrolytes

NASA Astrophysics Data System (ADS)

Shukur, M. F.; Yusof, Y. M.; Zawawi, S. M. M.; Illias, H. A.; Kadir, M. F. Z.

2013-11-01

This paper focuses on the conductivity and transport properties of chitosan-based solid biopolymer electrolytes containing ammonium thiocyanate (NH4SCN). The sample containing 40 wt% NH4SCN exhibited the highest conductivity value of (1.81 ± 0.50) × 10-4 S cm-1 at room temperature. Conductivity has increased to (1.51 ± 0.12) × 10-3 S cm-1 with the addition of 25 wt% glycerol. The temperature dependence of conductivity for both salted and plasticized systems obeyed the Arrhenius rule. The activation energy (Ea) was calculated for both systems and it is found that the sample with 40 wt% NH4SCN in the salted system obtained an Ea value of 0.148 eV and that for the sample containing 25 wt% glycerol in the plasticized system is 0.139 eV. From the Fourier transform infrared studies, carboxamide and amine bands shifted to lower wavenumbers, indicating that chitosan has interacted with NH4SCN salt. Changes in the C-O stretching vibration band intensity are observed at 1067 cm-1 with the addition of glycerol. The Rice and Roth model was used to explain the transport properties of the salted and plasticized systems.

Evaluation of Laser-Induced Breakdown Spectroscopy (LIBS) for Measurement of Silica on Filter Samples of Coal Dust

PubMed Central

Stipe, Christopher B.; Miller, Arthur L.; Brown, Jonathan; Guevara, Edward; Cauda, Emanuele

2015-01-01

Airborne silica dust (quartz) is common in coal mines and represents a respiratory hazard that can lead to silicosis, a potentially fatal lung disease. With an eye toward developing a portable monitoring device for rapid analysis of silica dust, laser-induced breakdown spectroscopy (LIBS) was used to quantify quartz in coal dust samples collected on filter media. Pure silica (Min-U-Sil™ 5), Georgia kaolin, and Pittsburgh-4 and Illinois-6 coal dusts were deposited separately and at multiple mass loadings onto 37-mm polyvinylchloride (PVC) filters. LIBS-generated silicon emission was monitored at 288.16 nm, and non-silica contributions to that signal from kaolinite were removed by simultaneously detecting aluminum. Measurements of the four samples were used to calculate limits of detection (LOD) for silicon and aluminum of approximately 0.08 µg/cm2 and 0.05 µg/cm2, respectively (corresponding to 0.16 µg/cm2 and 0.20 µg/cm2 for silica and kaolinite, respectively). Relative errors of prediction are around 10%. Results demonstrate that LIBS can dependably quantify silica on filter samples of coal dust and confirm that accurate quantification can be achieved for very lightly loaded samples, which supports the potential application of LIBS for rapid, in-field monitoring. PMID:23146184

Evaluation of laser-induced breakdown spectroscopy (LIBS) for measurement of silica on filter samples of coal dust.

PubMed

Stipe, Christopher B; Miller, Arthur L; Brown, Jonathan; Guevara, Edward; Cauda, Emanuele

2012-11-01

Airborne silica dust (quartz) is common in coal mines and represents a respiratory hazard that can lead to silicosis, a potentially fatal lung disease. With an eye toward developing a portable monitoring device for rapid analysis of silica dust, laser-induced breakdown spectroscopy (LIBS) was used to quantify quartz in coal dust samples collected on filter media. Pure silica (Min-U-Sil™ 5), Georgia kaolin, and Pittsburgh-4 and Illinois-6 coal dusts were deposited separately and at multiple mass loadings onto 37-mm polyvinylchloride (PVC) filters. LIBS-generated silicon emission was monitored at 288.16 nm, and non-silica contributions to that signal from kaolinite were removed by simultaneously detecting aluminum. Measurements of the four samples were used to calculate limits of detection (LOD) for silicon and aluminum of approximately 0.08 μg/cm(2) and 0.05 μg/cm(2), respectively (corresponding to 0.16 μg/cm(2) and 0.20 μg/cm(2) for silica and kaolinite, respectively). Relative errors of prediction are around 10%. Results demonstrate that LIBS can dependably quantify silica on filter samples of coal dust and confirm that accurate quantification can be achieved for very lightly loaded samples, which supports the potential application of LIBS for rapid, in-field monitoring.

Investigation on the behavioral difference in third order nonlinearity and optical limiting of Mn0.55Cu0.45Fe2O4 nanoparticles annealed at different temperatures

NASA Astrophysics Data System (ADS)

Yuvaraj, S.; Manikandan, N.; Vinitha, G.

2017-11-01

Mn0.55Cu0.45Fe2O4 nanoparticles were synthesized by wet chemical co-precipitation method. The obtained samples were annealed at different temperatures (500 °C to 1250 °C). All annealed samples were characterized for their structural, magnetic, linear and non-linear optical properties. XRD results confirm single phase cubic spinel structure only for samples annealed at 800 °C and 1250 °C. The average crystallite sizes of the samples are in the range of 11-37 nm. HR-SEM image of the sample annealed at 800 °C exposed spherical morphology. The quantitative analysis of EDX results is close to the expected values. Bandgaps were evaluated from UV-DRS. The FTIR spectrum showing the essential peaks around 452.1 and 567.2 cm-1 prove the formation of spinel nanoparticles. In PL spectrum, a broad emission peak is attained in visible region at 485 nm. The saturation magnetization (M s), coercivity (H c) and remanence magnetization (M r) are obtained from the hysteresis curve. Nonlinear absorption coefficients (10-4 cm W-1), nonlinear indices of refraction (10-8 cm2 W-1) and the third order nonlinear susceptibilities (10-6 esu) are determined using Z-scan experiment. CW laser beam is utilized to study the optical limiting characteristics and the results prove these materials to be a potential candidate for device applications like optical switches and power limiters.

Statistical Assessment of a Paired-site Approach for Verification of Carbon and Nitrogen Sequestration on CRP Land

NASA Astrophysics Data System (ADS)

Kucharik, C.; Roth, J.

2002-12-01

The threat of global climate change has provoked policy-makers to consider plausible strategies to slow the accumulation of greenhouse gases, especially carbon dioxide, in the atmosphere. One such idea involves the sequestration of atmospheric carbon (C) in degraded agricultural soils as part of the Conservation Reserve Program (CRP). While the potential for significant C sequestration in CRP grassland ecosystems has been demonstrated, the paired-site sampling approach traditionally used to quantify soil C changes has not been evaluated with robust statistical analysis. In this study, 14 paired CRP (> 8 years old) and cropland sites in Dane County, Wisconsin (WI) were used to assess whether a paired-site sampling design could detect statistically significant differences (ANOVA) in mean soil organic C and total nitrogen (N) storage. We compared surface (0 to 10 cm) bulk density, and sampled soils (0 to 5, 5 to 10, and 10 to 25 cm) for textural differences and chemical analysis of organic matter (OM), soil organic C (SOC), total N, and pH. The CRP contributed to lowering soil bulk density by 13% (p < 0.0001) and increased SOC and OM storage (kg m-2) by 13 to 17% in the 0 to 5 cm layer (p = 0.1). We tested the statistical power associated with ANOVA for measured soil properties, and calculated minimum detectable differences (MDD). We concluded that 40 to 65 paired sites and soil sampling in 5 cm increments near the surface were needed to achieve an 80% confidence level (α = 0.05; β = 0.20) in soil C and N sequestration rates. Because soil C and total N storage was highly variable among these sites (CVs > 20%), only a 23 to 29% change in existing total organic C and N pools could be reliably detected. While C and N sequestration (247 kg C ha{-1 } yr-1 and 17 kg N ha-1 yr-1) may be occurring and confined to the surface 5 cm as part of the WI CRP, our sampling design did not statistically support the desired 80% confidence level. We conclude that usage of statistical power analysis is essential to insure a high level of confidence in soil C and N sequestration rates that are quantified using paired plots.

Superemission in vertically-aligned single-wall carbon nanotubes

NASA Astrophysics Data System (ADS)

Khmelinskii, Igor; Makarov, Vladimir

2016-09-01

Presently we used two samples of vertically aligned single-wall carbon nanotubes (VA SWCNTs) with parallelepiped geometry, sized 0.02 cm × 0.2 cm × 1.0 cm and 0.2 cm × 0.2 cm × 1.0 cm. We report absorption and emission properties of the VA SWCNTs, including strong anisotropy in both their absorption and emission spectra. We found that the emission spectra extend from the middle-IR range to the near-IR range, with such extended spectra being reported for the first time. Pumping the VA SWCNTs in the direction normal to their axis, superemission (SE) was observed in the direction along their axis. The SE band maximum is located at 7206 ± 0.4 cm-1. The energy and the power density of the superemission were estimated, along with the diffraction-limited divergence. At the pumping energy of 3 mJ/pulse, the SE energy measured by the detector was 0.74 mJ/pulse, corresponding to the total SE energy of 1.48 mJ/pulse, with the energy density of 18.5 mJ cm-2/pulse and the SE power density of 1.2 × 105 W cm-2/pulse. We report that a bundle of VA SWCNTs is an emitter with a relatively small divergence, not exceeding 3.9 × 10-3 rad. We developed a theoretical approach to explain such absorption and emission spectra. The developed theory is based on the earlier proposed SSH theory, which we extended to include the exchange interactions between the closest SWCNT neighbors. The developed theoretical ideas were implemented in a homemade FORTRAN code. This code was successfully used to calculate and reproduce the experimental spectra and to determine the SWCNT species that originate the respective absorption bands, with acceptable agreement between theory and experiment.

Leaching of pesticides through normal-tillage and low-tillage soil--a lysimeter study. I. Isoproturon.

PubMed

Fomsgaard, Inge S; Spliid, Niels Henrik; Felding, Gitte

2003-01-01

Isoproturon is a herbicide, which was used in Denmark against grass weeds and broad-leaved weeds until 1998. Isoproturon has frequently been detected in ground water monitoring studies. Leaching of isoproturon (N,N-dimethyl-N'-(4-(1-methylethyl)-phenyl)urea) and its metabolites, N'-(4-isopropylphenyl)-N-methylurea and N'-(4-isopropylphenyl)urea was studied in four lysimetres, two of them being replicates from a low-tillage field (lysimeter 3 and 4), the other two being replicates from a normal tillage field (lysimeter 5 and 6). In both cases the soil was a sandy loam soil with 13-14% clay. The lysimetres had a surface area of 0.5 m2 and a depth of 110 cm. Lysimeter 3 and 4 were sprayed with unlabelled isoproturon while lysimeter 5 and 6 was sprayed with a mixture of 14C-labelled and unlabelled isoproturon. The total amount of isoproturon sprayed onto each lysimeter was 63 mg, corresponding to 1.25 kg active ingredient per ha. The lysimeters were sprayed with isoproturon on October 26, 1997. The lysimetres were installed in an outdoor system in Research Centre Flakkebjerg and were thus exposed to normal climatic conditions of the area. A mean of 360 l drainage water were collected from lysimeter 3 and 4 and a mean of 375 litres from lysimeter 5 and 6. Only negligible amounts of isoproturon and its primary metabolites were found in the drainage water samples, and thus no significant difference between the two lysimeter sets was shown. In a total of 82 drainage water samples, evenly distributed between the four lysimetres isoproturon was found in detectable amounts in two samples and N'-(4-isopropylphenyl)urea was found in detectable amounts in two other samples. The detection limit for all the compounds was 0.02 microg/l. 48% and 54% of the added radioactivity were recovered from the upper 10 cm soil layer in lysimeter 5 and 6, respectively, and 17 and 14% from 10-20 cm's depth. By extraction first with an aquatic CaCl2 solution 0.49% of the added radioactivity was extracted from the upper 10 cm layer in lysimeter 5. In the subsequent extraction with acetonitril, 1.19% of the added radioactivity was extracted. In lysimeter 6, upper 10 cm, 0.2% were extracted with water and 0.56% were extracted with acetonitril. Below 10 cm's depth no measurable amounts could be extracted.

Comparison of two non-invasive methods of microbial analysis in surgery practice: incision swabbing and the indirect imprint technique.

PubMed

Chovanec, Zdenek; Veverkova, Lenka; Votava, Miroslav; Svoboda, Jiri; Jedlicka, Vaclav; Capov, Ivan

2014-12-01

A variety of methods exist to take samples from surgical site infections for cultivation; however, an unambiguous and suitable method has not yet been defined. The aim of our retrospective non-randomized study was to compare two non-invasive techniques of sampling material for microbiologic analysis in surgical practice. We compared bacteria cultured from samples obtained with the use of the swab technique, defined in our study as the gold standard, with the indirect imprint technique. A cotton-tipped swab (Copan, Brescia, Italy) was used; the imprints were taken using Whatman no. 4 filter paper (Macherey-Nagal, Duren, Germany) cut into 5×5 cm pieces placed on blood agar in a Petri dish. To culture the microorganisms in the microbiology laboratory, we used blood agar, UriSelect 4 medium (Bio-Rad, Marnes-la-Coquette, France), and a medium with sodium chloride (blood agar with salt). After careful debridement, a sample was taken from the incision surface by swab and subsequently the same area of the surface was imprinted onto filter paper. The samples were analyzed in the microbiology laboratory under standard safety precautions. The cultivation results of the two techniques were processed statistically using contingency tables and the McNemar test. Those samples that were simultaneously cultivation-positive by imprint and -negative by swabbing were processed in greater detail. Over the period between October 2008 and March 2013, 177 samples from 70 patients were analyzed. Sampling was carried out from 42 males and 28 females. One hundred forty-six samples were from incisions after operations (21 samples from six patients after operation on the thoracic cavity, 73 samples from 35 patients after operation on the abdominal cavity combined with the gastrointestinal tract, 52 samples from 19 patients with other surgical site infections not included above) and 31 samples from 11 patients with no post-operative infection. One patient had a sample taken both from a post-operative and a non-post-operative site. Coincidently, the most frequent cultivation finding with both techniques was a sterile one (imprint, 62; swab, 50). The microorganism cultivated most frequently after swabbing was Pseudomonas aeruginosa (22 cases), compared with Escherichia coli when the filter paper (imprint) was used (31 cases). The imprint technique was evaluated as more sensitive compared with swabbing (p=0.0001). The κ statistic used to evaluate the concordance between the two techniques was 0.302. Of the 177 samples there were 53 samples simultaneously sterile using the swab and positive in the imprint. In three samples colony- forming units (CFU) were not counted; 22 samples were within the limit of 0-25×10(1) CFU/cm(2), 20 samples within the limit of 25×10(1)-25×10(2) CFU/cm(2), five within the limit of 25×10(2)-25×10(3) CFU/cm(2), and three of more than 25×10(4) CFU/cm(2). The hypothesis of swabbing as a more precise technique was not confirmed. In our study the imprint technique was more sensitive than swabbing; the strength of agreement was fair. We obtained information not only on the type of the microorganism cultured, but also on the number of viable colonies, expressed in CFU/cm(2).

Effect of ultrasonic cavitation on the diffusivity of a point defect in the passive film on formed Nb in 0.5 M HCl solution.

PubMed

Li, D G

2015-11-01

This work primarily focused on the influence of ultrasonic cavitation on the transport property of the point defect in the passive film on formed Nb in 0.5M HCl solution via electrochemical techniques based on the point defect model (PDM). The influence of ultrasonic cavitation on the composition and structure of the passive film was detected by X-ray photoelectron spectroscopy (XPS) and Auger electron spectroscopy (AES). The transport property of a point defect in the passive film was characterized by the diffusivity of the point defect (D0). The influences of the ultrasonic cavitation power, passivated time and the distance between horn bottom and sample surface on D0 were analyzed. The results demonstrated that the passive film formed on Nb was an n-type semiconductor with a donor density (ND) ranging from 10(19) cm(-3) to 10(20) cm(-3) in the case of static state, while the order of ND increased one to two times by applying ultrasonic cavitation during film formation. The diffusivity of the point defect (D0) in the passive film formed on Nb at 0.5 V for 1 h in a 0.5 M HCl solution in the static state was calculated to be 9.704×10(-18) cm(2) s(-1), and it increased to 1.255×10(-16) cm(2) s(-1), 7.259×10(-16) cm(2) s(-1) and 7.296×10(-15) cm(2) s(-1) when applying the 180 W, 270 W and 450 W ultrasonic cavitation powers during film formation. D0 increased with the increment of the ultrasonic cavitation power, and decreased with the increased in formation time and distance between the horn bottom and sample surface. AES results showed the film structure and composition were changed by applying the ultrasonic cavitation. XPS results revealed that the passive film was mainly composed of Nb2O5 in the static state, and the low valence Nb-oxide (NbO) appeared in the passive film except Nb2O5 in the case of applying a 270 W ultrasonic cavitation power. Copyright © 2015 Elsevier B.V. All rights reserved.

Structural, microstructural and electrical characterization of BaSnO3 and Ba0.90Y0.10SnO3 synthesized by solution combustion method

NASA Astrophysics Data System (ADS)

Kumar, Upendra; Yadav, Dharmendra; Upadhyay, Shail; Thakur, Anukul K.

2018-04-01

Powder of perovskite oxides BaSnO3 and Ba0.90Y0.10SnO3 have been synthesized by solution combustion method. Rietveld profile analysis shows that the phases crystallize with cubic unit cell in the space group pm3m. Further purity of the synthesized powders was checked by Fourier transform of infrared (FTIR) spectroscopy. The average grain size of the sintered samples was obtained using Scanning electron microscopy (SEM) and found to be 4.9 and 2.8 1m for BaSnO3 and Ba0.90Y0.10SnO3, respectively. The AC conductivity (σac) of synthesized samples was measured in the frequency range from 24Hz-1MHz and temperature range 100 - 600°C. Conductivity spectra of both the samples followed universal Johnscher's power law at different temperatures. The value of bulk or dc conductivity (σdc) at different temperatures has been extracted by fitting the Johnscher's power law to AC conductivity spectra. The activation energy for σc has been obtained from the least square linear fit of data points and found to be 0.53 eV and 0.43 eV, respectively for BaSnO3 and Ba0.90Y0.10SnO3. Based on the value of activation energy it is proposed that conduction in these samples is govern via hopping of (OH)•. The value of conductivity at temperature 550°C of Ba0.90Y0.10SnO3 is 0.00406 S-cm-1 higher than BaSnO3 (0.00173 S-cm-1) at the same temperature.

Refine phosphorus stratification caused by long-term tillage and P fertilisation in maize -soybean rotation in eastern Canada

NASA Astrophysics Data System (ADS)

Ziadi, Noura; Morel, Christian

2017-04-01

The use of conservation tillage for crops production worldwide has increased markedly over recent years. Nutrient distributions under no-till (NT) compared with conventional moldboard tillage (CT) management in the cold, humid region of the eastern Canada need to be assessed for future placement, quantity, and type of fertilizers to efficiently match crop demands. We determined soil-profile distributions of soil total C (TC), total N (TN), and phosphate ions concentration (CP) in soil solution to a depth of 0.4 m after 23 years of continuous CT and NT management at different P fertilization rates on a clay loam soil in eastern Canada cropped with grain maize -soybean rotation. The experimental site was initiated in 1992 in southern Quebec, Canada. In August 2014, soil samples were collected at five profiles: 0 to 5, 5 to 10, 10 to 20, 20 to 30 and 30 to 40 cm under CT and NT fertilized at three P fertilizations (0 (P0), 17.5 (P0.5), and 35 (P1) kg P ha-1 applied as triple superphosphate on maize at 5 cm depth). To refine CNP stratification analysis for NT-P0 and NT-P1, supplemental soils of the 0-5 cm layer were sampled in P0 and P1 and then cutting into 5 layers of 1 cm. Different patterns for CP in relation to P fertilization under CT and NT were observed at the five profiles. The CP values did not differ significantly within ploughed layer but increased with P fertilization, e.g. 0.031, 0.066, and 0.075 mg P L-1 for P0, P0.5 and P1, respectively. Significant decline was observed in deeper depth beyond the plough. The Cp results in NT-P0 did not differ significantly to those of MP-P0. By contrast, highly significant P stratifications were observed in NT-P0.5 and NT-P1, especially marked in NT-P1 for which the CP value in 0-5 cm layer (0.35 mg P L-1) was 50 times greater than that in 30-40 cm layer (0.007 mg P L-1). To refine the C, N, and P stratifications, supplemental sampling was carried out in the 0-5 cm to cut this layer every 1 cm depth for P0 and P1. Most dramatic changes occurred within the 0-5 cm depth. The CP value in the first cm of soil (0.20 mg P L-1) was four times greater than that in the 4-5 cm layer (0.049 mg P L-1) of soil. The main reason for the large P accumulation in the first centimeter of soil is the annual return of plant residues to the soil surface. The stratification of TC and TN within the 0-5 cm layer showed similar trends irrespective of P fertilization. Under NT, the magnitude of CNP stratifications within the 0-1 cm layer to the 4-5 cm layer is equivalent to that observed in the 0-5 cm layer to the 30-40 cm layer.

[Determination of ephedrine hydrochloride, pseudoephedrine hydrochloride and methylephedrine hydrochloride in maxingshigan decoction by CE].

PubMed

Yu, Li-ping; Wang, Xiao-ke; Luo, Jia-bo

2011-04-01

To establish the method for determination of ephedrine hydrochloride, pseudoephedrine hydrochloride and methylephedrine hydrochloride in maxingshigan decoction by capillary electrophoresis. The separation was performed on a fused silica capillary of 60 cm x 55 microcrpm ID (52 cm of effective length). 60 mmol/L NaB4O7 + 10% (V/V) CH3OH (pH 9.0) was selected as the running buffer. The separation voltage was 12 kV. The samples was injected by gravity (10 s, 15 cm). The detection wavelength was 210 nm and berberine hydrochloride was the internal standard. The linear range of determination for ephedrine hydrochloride, pseudoephedrine hydrochloride and methylephedrine hydrochloride were 20.0-160.0 microg/mL (r = 0.9999), 7.5-60.0 microg/mL (r = 0.9991) and 2.0-10.0 microg/mL (r = 0.9993). The average recoveries were 98.0%, 97.0% and 97.8%, the precisions of the method were 2.31%, 2.21% and 2.00% (n=6), respectively. The method is convenient, rapid and accurate for the quality control of maxingshigan decoction.

Compositional, structural, and optical changes of polyimide implanted by 1.0 MeV Ni+ ions

NASA Astrophysics Data System (ADS)

Mikšová, R.; Macková, A.; Pupikova, H.; Malinský, P.; Slepička, P.; Švorčík, V.

2017-09-01

The ion irradiation leads to deep structural and compositional changes in the irradiated polymers. Ni+ ions implanted polymers were investigated from the structural and compositional changes point of view and their optical properties were investigated. Polyimide (PI) foils were implanted with 1.0 MeV Ni+ ions at room temperature with fluencies of 1.0 × 1013-1.0 × 1015 cm-2 and two different ion implantation currents densities (3.5 and 7.2 nA/cm2). Rutherford Back-Scattering (RBS) and Elastic Recoil Detection Analysis (ERDA) were used for determination of oxygen and hydrogen escape in implanted PI. Atomic Force Microscopy (AFM) was used to follow surface roughness modification after the ion implantation and UV-Vis spectroscopy was employed to check the optical properties of the implanted PI. The implanted PI structural changes were analysed using Attenuated Total Reflection Fourier Transform Infrared Spectroscopy (ATR-FTIR). High energy Ni-ion implantation causes only a minor release of hydrogen and oxygen close to the polymer sub-surface region in about 60 nm thick layer penetrated by the ion beam; especially at ion fluencies below 1.0 × 1014 cm-2. The mostly pronounced structural changes of the Ni implanted PI were found for the samples implanted above ion fluence 1.0 × 1015 cm-2 and at the ion current density 7.2 nA/cm2, where the optical band gap significantly decreases and the reduction of more complex structural unit of PI monomer was observed.

Modelling and mapping the topsoil organic carbon content for Tanzania

NASA Astrophysics Data System (ADS)

Kempen, Bas; Kaaya, Abel; Ngonyani Mhaiki, Consolatha; Kiluvia, Shani; Ruiperez-Gonzalez, Maria; Batjes, Niels; Dalsgaard, Soren

2014-05-01

Soil organic carbon (SOC), held in soil organic matter, is a key indicator of soil health and plays an important role in the global carbon cycle. The soil can act as a net source or sink of carbon depending on land use and management. Deforestation and forest degradation lead to the release of vast amounts of carbon from the soil in the form of greenhouse gasses, especially in tropical countries. Tanzania has a high deforestation rate: it is estimated that the country loses 1.1% of its total forested area annually. During 2010-2013 Tanzania has been a pilot country under the UN-REDD programme. This programme has supported Tanzania in its initial efforts towards reducing greenhouse gas emission from forest degradation and deforestation and towards preserving soil carbon stocks. Formulation and implementation of the national REDD strategy requires detailed information on the five carbon pools among these the SOC pool. The spatial distribution of SOC contents and stocks was not available for Tanzania. The initial aim of this research, was therefore to develop high-resolution maps of the SOC content for the country. The mapping exercise was carried out in a collaborative effort with four Tanzanian institutes and data from the Africa Soil Information Service initiative (AfSIS). The mapping exercise was provided with over 3200 field observations on SOC from four sources; this is the most comprehensive soil dataset collected in Tanzania so far. The main source of soil samples was the National Forest Monitoring and Assessment (NAFORMA). The carbon maps were generated by means of digital soil mapping using regression-kriging. Maps at 250 m spatial resolution were developed for four depth layers: 0-10 cm, 10-20 cm, 20-30 cm, and 0-30 cm. A total of 37 environmental GIS data layers were prepared for use as covariates in the regression model. These included vegetation indices, terrain parameters, surface temperature, spectral reflectances, a land cover map and a small-scale Soil and Terrain (SOTER) map. Prediction uncertainty was quantified by the 90% prediction interval and the predictions were validated by cross-validation. The SOTER map proved to be the best predictor of SOC content, followed by the terrain parameters, mid-infrared reflectance, surface temperature, several vegetation indices, and the land cover map. The maps show that the SOC content decreases with depth, which is typically observed in soils. For the 0-10 cm layer the average predicted SOC content is 1.31%, for the 10-20 cm layer this is 0.93%, for the 20-30cm layer 0.72%, and for the 0-30cm layer 1.00%. The mean absolute error of the 0-10cm layer was 0.54%, that of the 10-20cm layer 0.38%, that of the 20-30cm layer 0.31%, and that of the 0-30cm layer 0.34%. The R2-value of the 0-10 cm layer was 0.47, that of the 10-20cm layer 0.49, that of the 20-30cm layer 0.44, and that of the 0-30cm layer 0.59. The next step will be the development of maps of SOC stock and key properties that are of interest for soil fertility management such as pH and the textural fractions.

A genomic scan for age at onset of Alzheimer's disease in 437 families from the NIMH Genetic Initiative.

PubMed

Dickson, M Ryan; Li, Jian; Wiener, Howard W; Perry, Rodney T; Blacker, Deborah; Bassett, Susan S; Go, Rodney C P

2008-09-05

We performed linkage analysis for age at onset (AAO) in the total Alzheimer's disease (AD) NIMH sample (N = 437 families). Families were subset as late-onset (320 families, AAO > or = 65) and early/mixed (117 families, at least 1 member with 50 < AAO < 65). Treating AAO as a censored trait, we obtained the gender and APOE adjusted residuals in a parametric survival model and analyzed the residuals as the quantitative trait (QT) in variance-component linkage analysis. For comparison, AAO-age at exam (AAE) was analyzed as the QT adjusting for affection status, gender, and APOE. Heritabilities for residual and AAO-AAE outcomes were 66.3% and 74.0%, respectively for the total sample, 56.0% and 57.0% in the late-onset sample, and 33.0% for both models in the early/mixed sample. The residual model yielded the largest peaks on chromosome 1 with LOD = 2.0 at 190 cM in the total set, LOD = 1.7 at 116 cM on chromosome 3 in the early/mixed subset, and LOD = 1.4 at 71 and 86 cM, respectively, on chromosome 6 in the late-onset subset. For the AAO-AAE outcome model the largest peaks were identified on chromosome 1 at 137 cM (LOD = 2.8) and chromosome 6 at 69 cM (LOD = 2.3) and 86 cM (LOD = 2.2) all in the late-onset subset. Additional peaks with LOD > or = 1 were identified on chromosomes 1, 2, 3, 6, 8, 9, 10, and 12 for the total sample and each subset. Results replicate previous findings, but identify additional suggestive peaks indicating the genetics of AAO in AD is complex with many chromosomal regions potentially containing modifying genes. 2008 Wiley-Liss, Inc.

Search for Excess Dimuon Production in the Radial Region (1.6 < r < 10) cm at the D0 Experiment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Williams, Mark; Collaboration, for the D0

2009-06-01

We report on a study of dimuon events produced in p{bar p} collisions at {radical}s = 1.96 TeV, using 0.9 fb{sup -1} of data recorded by the D0 experiment during 2008. Using information from the inner-layer silicon tracking detector, we observe 712 {+-} 462 {+-} 942 events in which one or both muons are produced in the range 1.6 < r {approx}< 10 cm, which is expressed as a fraction (0.40 {+-} 0.26 {+-} 0.53)% of the total dimuon sample. We therefore see no significant excess of muons produced a few centimeters away from the interaction point.

Optimization of single plate-serial dilution spotting (SP-SDS) with sample anchoring as an assured method for bacterial and yeast cfu enumeration and single colony isolation from diverse samples.

PubMed

Thomas, Pious; Sekhar, Aparna C; Upreti, Reshmi; Mujawar, Mohammad M; Pasha, Sadiq S

2015-12-01

We propose a simple technique for bacterial and yeast cfu estimations from diverse samples with no prior idea of viable counts, designated as single plate-serial dilution spotting (SP-SDS) with the prime recommendation of sample anchoring (10 0 stocks). For pure cultures, serial dilutions were prepared from 0.1 OD (10 0 ) stock and 20 μl aliquots of six dilutions (10 1 -10 6 ) were applied as 10-15 micro-drops in six sectors over agar-gelled medium in 9-cm plates. For liquid samples 10 0 -10 5 dilutions, and for colloidal suspensions and solid samples (10% w/v), 10 1 -10 6 dilutions were used. Following incubation, at least one dilution level yielded 6-60 cfu per sector comparable to the standard method involving 100 μl samples. Tested on diverse bacteria, composite samples and Saccharomyces cerevisiae , SP-SDS offered wider applicability over alternative methods like drop-plating and track-dilution for cfu estimation, single colony isolation and culture purity testing, particularly suiting low resource settings.

VizieR Online Data Catalog: LMC and Cen A 1.3-10GHz polarization behavior (Anderson+, 2016)

NASA Astrophysics Data System (ADS)

Anderson, C. S.; Gaensler, B. M.; Feain, I. J.

2016-08-01

The targets for our study were selected from among two archival polarization data sets, which were observed and processed by several independent groups. i.e. LMC observations spanning from 1994 Oct to 1996 Jan in 1.328-1.432GHz band; Cen A observations spanning from 2006 Dec to 2008 Feb in 1.296-1.480GHz band. We observed the 40 sample sources using the Australia Telescope Compact Array (ATCA) over 1.1-3.1GHz (16cm), 4.5-6.5GHz (6cm), and 8.0-10.0GHz (3cm) in full polarization with a nominal 1MHz channel resolution between 2012 Feb 10-12 and 2012 Aug 17-19. We imaged each source in Stokes I, Q, and U at 20MHz intervals through the 16 and 6cm bands, and at a substantially coarser resolution of 200MHz in the 3cm band. See sections 2 and 3 for further explanations. (2 data files).

Structural and dielectric studies of Zr and Co co-substituted Ni0.5Zn0.5Fe2O4 using sol-gel auto combustion method

NASA Astrophysics Data System (ADS)

Jalaiah, K.; Vijaya Babu, K.; Rajashekhar Babu, K.; Chandra Mouli, K.

2018-06-01

Zr and Co substituted Ni0.5Zn0.5 ZrxCuxFe2-2xO4 with x values varies from the 0.0 to 0.4 in steps of 0.08 wt% ferrites synthesized by using sol-gel auto combustion method. The XRD patterns give evidence for formation of the single phase cubic spinel. The lattice constant was initially decreased from 8.3995 Å to 8.3941 Å with dopant concentration for x = 0.00-0.08 thereafter the lattice parameter steeply increased up to 8.4129 Å fox x = 0.4 with increasing dopant concentration. The estimated crystallite size and measured particle sizes are in comparable nano size. The grain size initially increased 2.3137-3.0430 μm, later it decreased to 2.2952 μm with increasing dopant concentration. The prepared samples porosity shows the opposite trend to grain size. The FT-IR spectrum for prepared samples shows the Fd3m (O7h). The wavenumber for tetrahedral site increased from 579 cm-1 to 593 cm-1 with increasing dopant concentration and the wavenumber of octahedral site are initially decreased from 414 cm-1 to 400 cm-1 for x = 0.00 to x = 0.08 later increased to 422 cm-1 with increasing dopant concentration. The dielectric constant increased from 8.85 to 34.5127 with dopant increasing concentration. The corresponding loss factor was fallows the similar trend as dielectric constant. The AC conductivity increased with increasing dopant concentration from 3.0261 × 10-7 S/m to 4.4169 × 10-6 S/m.

Germanium- and tellurium-doped GaAs for non-alloyed p-type and n-type ohmic contacts

NASA Astrophysics Data System (ADS)

Park, Joongseo; Barnes, Peter A.; Lovejoy, Michael L.

1995-08-01

Epitaxial ohmic contacts to GaAs were grown by liquid phase epitaxy. Heavily Ge-doped GaAs was grown to prepare ohmic contacts to p-GaAs while Te was used for the n-type contacts. Hall measurements were carried out for the samples grown from melts in which the mole fraction of Ge was varied between 1.55 atomic % and 52.2 atomic %, while the Te mole fractions varied between 0.03% and 0.5%. Specific contact resistance, rc, as low as rcp=2.9×10-6 ohm-cm 2 for Ge doping of p=(Na-Nd)=6.0×1019 holes/cm3 was measured for p-contacts and rcn=9.6×10-5 ohm-cm2 was measured for Te doping of n=(Nd-Na)=8.9×1018 electrons/cm3 for GaAs metallized with non-alloyed contacts of Ti/Al.

Microbial effect of steam vacuum pasteurisation implemented after slaughtering and dressing of sheep and lamb.

PubMed

Hassan, Ammar Ali; Skjerve, Eystein; Bergh, Claus; Nesbakken, Truls

2015-01-01

The main objective of the study was to assess the effect of steam vacuum pasteurisation on carcass contamination with focus on Escherichia coli, Enterobacteriaceae and total plate count (TPC). Additionally, the effect of an additional tryptone soy agar (TSA) step for resuscitation of Enterobacteriaceae after steam vacuum pasteurisation was investigated. Steam vacuum pasteurisation was applied at a temperature of >82°C for a duration of 10s on sheep and lamb carcasses (n=120). Samples were taken immediately: i) after trimming just before the use of steam vacuum and ii) after use of steam vacuum. Nordic Committee on Food Analysis methods were used in microbial analyses. The differences in log reduction were found significant for all of the three microorganisms (p<0.05). For TPC, the general reduction was a 0.65 log10 in the number of colony forming units (CFU) per cm(2). For E. coli, the median reduction effect on carcasses positive before decontamination was 1.1 log10 CFU/cm(2). A large variability of the effect was however found, with 50% of the figures ranging from a 0.24 to 1.62 log10 CFU/cm(2) reduction and a 10-90% range of 0-2.1. The number of positive carcasses with Enterobacteriaceae after steam vacuum pasteurisation was higher in samples where TSA+violet red bile glucose agar (VRBGA) was used compared to samples where only VRBGA was used (p<0.01). Steam vacuum pasteurisation was found efficient in reducing the total count, read as TPC, as well as the level of E. coli and Enterobacteriaceae. Copyright © 2014 Elsevier Ltd. All rights reserved.

Heat-physical properties of lunar surface material returned to earth by the Luna 16 automatic station

NASA Technical Reports Server (NTRS)

Avduyevskiy, V. S.; Anfimov, N. A.; Marov, M. Y.; Treskin, Y. A.; Shalayev, S. P.; Ekonomov, A. P.

1974-01-01

Density, specific heat capacity, and coefficient of thermal conductivity were studied on a sample of lunar surface material returned by the Luna 16 automatic station. The study was carried out in a helium-filled chamber. The density of the surface material when freely heaped was 1.2 g/cu cm, and when shaken down -- 1.7 g/cu cm. The specific heat capacity was 0.177 + or - 0.010 cal x g/1 x deg/1. The coefficient of thermal conductivity in the material was 4.8 x 10/6 + or - 1.2 x 10/6 cal x cm/1 x sec/1 x deg/1.

Fine structure of the late Eocene Ir anomaly in marine sediments

NASA Technical Reports Server (NTRS)

Asaro, F.

1991-01-01

The Late Eocene Ir abundance profile in deep sea cores from Ocean Drilling Program Leg 113 Hole 689B on the Maude Rise off of Antarctica was studied with 410 samples continuously in 10 cm increments and measured with the Iridium Coincidence (ICS). The ICS was subsequently modified to measure 13 other elements simultaneously with the Ir. The abundance profiles of these elements were then determined in the Late Eocene Massignano section in central Italy with 250 samples (encompassing roughly 2 million years of accumulation) which were collected about every 5 cm in about 2 cm increments. These studies augmented a previous one (which included many elements) of deep sea cores from Deep Sea Drilling Project Site 592 on the Lord Howe Rise in the Tasman Sea between Australia and New Zealand. In the latter study, 50 samples (encompassing roughly 0.7 million years of accumulation) were collected continuously in 10 cm increments. The results from these studies are discussed.

RHELP (Regenerative High Efficiency Low Pressure) Air Purification System

DTIC Science & Technology

2009-06-18

with both SiC tubes and the fine granules was done by measuring THC concentration in the outlet air with the THC analyzer. When this was repeated...2.0 cm/s and 96.0% at 3.0 cm/s. This is close to what was seen originally without the plug. These results indicate that using THC concentration of...ratios of TB:AA from 1:0 to 1:16. ........ 34 Figure 25: df and Cv of samples with different PVP and F108 concentrations

Recruitment Maneuver Does not Increase the Risk of Ventilator Induced Lung Injury

PubMed Central

Akıncı, İbrahim Özkan; Atalan, Korkut; Tuğrul, Simru; Özcan, Perihan Ergin; Yılmazbayhan, Dilek; Kıran, Bayram; Basel, Ahmet; Telci, Lutfi; Çakar, Nahit

2013-01-01

Background: Mechanical ventilation (MV) may induce lung injury. Aims: To assess and evaluate the role of different mechanical ventilation strategies on ventilator-induced lung injury (VILI) in comparison to a strategy which includes recruitment manoeuvre (RM). Study design: Randomized animal experiment. Methods: Thirty male Sprague-Dawley rats were anaesthetised, tracheostomised and divided into 5 groups randomly according to driving pressures; these were mechanically ventilated with following peak alveolar opening (Pao) and positive end-expiratory pressures (PEEP) for 1 hour: Group 15-0: 15 cmH2O Pao and 0 cmH2O PEEP; Group 30-10: 30 cmH2O Pao and 10 cmH2O PEEP; Group 30-5: 30 cmH2O Pao and 5 cmH2O PEEP; Group 30-5&RM: 30 cmH2O Pao and 5 cmH2O PEEP with additional 45 cmH2O CPAP for 30 seconds in every 15 minutes; Group 45-0: 45 cmH2O Pao and 0 cmH2O PEEP Before rats were sacrificed, blood samples were obtained for the evaluation of cytokine and chemokine levels; then, the lungs were subsequently processed for morphologic evaluation. Results: Oxygenation results were similar in all groups; however, the groups were lined as follows according to the increasing severity of morphometric evaluation parameters: Group 15-0: (0±0.009) < Group 30-10: (0±0.14) < Group 30-5&RM: (1±0.12) < Group 30-5: (1±0.16) < Group 45-0: (2±0.16). Besides, inflammatory responses were the lowest in 30-5&RM group compared to all other groups. TNF-α, IL-1β, IL-6, MCP-1 levels were significantly different between group 30-5&RM and group 15-0 vs. group 45-0 in each group. Conclusion: RM with low PEEP reduces the risk of ventilator-induced lung injury with a lower release of systemic inflammatory mediators in response to mechanical ventilation. PMID:25207105

Behaviour of co-inoculated pathogenic and spoilage bacteria on poultry following several decontamination treatments.

PubMed

Alonso-Hernando, Alicia; Capita, Rosa; Alonso-Calleja, Carlos

2012-10-01

The potential of chemical decontaminants to cause harmful effects on human health is among the causes of the rejection of antimicrobial treatments for removing surface contamination from poultry carcasses in the European Union. This study was undertaken to determine whether decontaminants might give a competitive advantage to pathogenic bacteria on poultry and involve a potential risk to consumer. A total of 144 chicken legs were co-inoculated with similar concentrations of pathogenic bacteria (Listeria monocytogenes, Staphylococcus aureus, Salmonella enterica serotype Enteritidis or Escherichia coli) and spoilage bacteria (Brochothrix thermosphacta or Pseudomonas fluorescens). Samples were dipped for 15min in solutions (w/v) of trisodium phosphate (12%; TSP), acidified sodium chlorite (1200ppm; ASC), citric acid (2%; CA), peroxyacids (220ppm; PA) or chlorine dioxide (50ppm; CD), or were left untreated (control). Microbiological analyses were carried out on day 0 and every 24h until day 7 of storage (at 10±1°C). The modified Gompertz equation was used as the primary model to fit observed data. TSP, ASC and CA were effective in extending the lag phase (L, ranging from 1.47±1.34days to 4.06±1.16days) and in decreasing the concentration of bacteria during the stationary phase (D, ranging from 2.46±0.51 log(10) cfu/cm(2) to 8.64±0.53 log(10) cfu/cm(2)), relative to the control samples (L values ranging from 0.59±0.38days and 2.52±2.28days, and D values ranging from 6.32±0.89 log(10) cfu/cm(2) to 9.39±0.39 log(10) cfu/cm(2), respectively). Both on untreated and on most decontaminated samples the overgrowth of spoilage bacteria among the species tested was observed throughout storage, suggesting that spoilage would occur prior to any noteworthy increase in the levels of pathogenic microorganisms. However, L. monocytogenes counts similar to, or higher than, those for spoilage bacteria were observed on samples treated with TSP, ASC or CA, suggesting that these treatments might pose a danger to consumers. However, these results derive from laboratory-based experiments testing artificially-inoculated bacteria. Further investigations of the natural micro-biota of poultry carcasses would be appropriate in order to substantiate these findings. Copyright © 2012 Elsevier B.V. All rights reserved.

Effect of solute lipophilicity on penetration through canine skin.

PubMed

Mills, P C; Magnusson, B M; Cross, S E

2003-12-01

To investigate the effect of lipophilicity on the percutaneous penetration of a homologous series of alcohols through canine skin. Skin harvested from Greyhound thorax was placed in Franz-type diffusion cells and the in vitro passage of radiolabelled (14C) alcohols (ethanol, butanol, hexanol and octanol (Log P 0.19-3.0)) through separate skin sections was measured in replicates of five. Permeability coefficient (kP, cm/h), maximum flux (Jmax, mol/cm2/h) and residue remaining within the skin were determined. The kP increased with increasing lipophilicity (6.2 x 10(-4) +/- 1.6 x 10(-4) cm/h for ethanol to 1.8 x 10(-2) +/- 3.6 x 10(-3) cm/h for octanol). Alcohol residues remaining within each skin sample followed a similar pattern. An exponential decrease in Jmax with increasing lipophilicity was observed. Changes in canine skin permeability occur with increasing alcohol lipophilicity. This finding has practical consequences for the design of topical formulations and optimisation of drug delivery through animal skin.

Controlling interface oxygen for forming Ag ohmic contact to semi-polar (1 1 -2 2) plane p-type GaN

NASA Astrophysics Data System (ADS)

Park, Jae-Seong; Han, Jaecheon; Seong, Tae-Yeon

2014-11-01

Low-resistance Ag ohmic contacts to semi-polar (1 1 -2 2) p-GaN were developed by controlling interfacial oxide using a Zn layer. The 300 °C-annealed Zn/Ag samples showed ohmic behavior with a contact resistivity of 6.0 × 10-4 Ω cm2 better than that of Ag-only contacts (1.0 × 10-3 Ω cm2). The X-ray photoemission spectroscopy (XPS) results showed that annealing caused the indiffusion of oxygen at the contact/GaN interface, resulting in the formation of different types of interfacial oxides, viz. Ga-oxide and Ga-doped ZnO. Based on the XPS and electrical results, the possible mechanisms underlying the improved electrical properties of the Zn/Ag samples are discussed.

Rheology of welding: experimental constraints

NASA Astrophysics Data System (ADS)

Quane, S. L.; Russell, J. K.; Kennedy, L. A.

2003-04-01

The rheological behavior of pyroclastic deposits during welding is incompletely understood and is based on a surprisingly small number of experimental studies. Previous pioneering experimental studies were done on small (1 cm thick) samples of ash/crystal mixtures under constant load. They established minimum welding temperatures between 600 and 700^oC under loads of 0.7 MPa (˜40 m of ignimbrite) to 3.6 MPa (˜250 m depth of ignimbrite). However, these data are neither sufficiently comprehensive nor coherent enough to fully describe the rheology of pyroclastic mixtures. In addition, previous studies did not examine the microstructural and geometric changes associated with welding compaction. Our goal is to provide accurate and comprehensive constitutive relationships between material properties, temperature, load and strain rate for pyroclastic material undergoing welding. Here we present results from a newly designed experimental apparatus. The experimental apparatus consists of a LoadTrac II fully automated uniaxial compression load frame manufactured by Geocomp Corporation. The load frame has a built in displacement transducer and can run both constant strain rate (10-6 to 0.25 cm/s) and constant load (up to 1150 kg) tests to a maximum displacement of 7.5 cm. The sample assembly comprises 5 cm diameter cylindrical upper and lower pistons (insulating ceramic with steel conductive ends) housed in a copper jacket. Samples are 5 cm diameter cores and can vary in length from 1 to 15 cm depending on experimental needs. A fiber insulated tube furnace capable of reaching temperatures ≈1000^oC surrounds the sample assembly. Temperature is measured using a thermocouple located inside the sample through the bottom piston; the furnace controller is capable of maintaining temperature fluctuations to <5^oC. Deformation experiments are performed on pre-fabricated cylinders of soda-lime glass beads and rhyolitic volcanic ash, as well as, cores of pumiceous rhyodacite. Experimental runs use strain rates of 10-4 and 10-5 cm/s and loads of ˜0 to 4.5 MPa. Experiments are run at temperatures between 400 and 850^oC corresponding to below and above the calorimetric glass transition temperatures of the respective materials. Data deriving from constant load and constant strain rate experiments are being used to constrain rheological models for welding of pyroclastic material.

Electrical properties of spin coated ultrathin titanium oxide films on GaAs

NASA Astrophysics Data System (ADS)

Dutta, Shankar; Pal, Ramjay; Chatterjee, Ratnamala

2015-04-01

In recent years, ultrathin (<50 nm) metal oxide films have been being extensively studied as high-k dielectrics for future metal oxide semiconductor (MOS) technology. This paper discusses deposition of ultrathin TiO2 films (˜10 nm) on GaAs substrates (one sulfur-passivated, another unpassivated) by spin coating technique. The sulfur passivation is done to reduce the surface states of GaAs substrate. After annealing at 400 °C in a nitrogen environment, the TiO2 films are found to be polycrystalline in nature with rutile phase. The TiO2 films exhibit consistent grain size of 10-20 nm with thickness around 10-12 nm. Dielectric constants of the films are found to be 65.4 and 47.1 corresponding to S-passivated and unpassivated substrates, respectively. Corresponding threshold voltages of the MOS structures are measured to be -0.1 V to -0.3 V for the S-passivated and unpassivated samples, respectively. The S-passivated TiO2 film showed improved (lower) leakage current density (5.3 × 10-4 A cm-2 at 3 V) compared to the unpassivated film (1.8 × 10-3 A/cm2 at 3 V). Dielectric breakdown-field of the TiO2 films on S-passivated and unpassivated GaAs samples are found to be 8.4 MV cm-1 and 7.2 MV cm-1 respectively.

A phantom for quantitation of partial volume effects in ECT

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mullani, N.A.

1989-02-01

A special phantom has been designed, built and tested to measure the quantitative recovery of ECT data from the heart as a function of the size of the object and the angulation of a 1 cm thick simulated myocardium inclined with respect to the image plane. The phantom consists of five objects of 0.5, 1.0, 1.5. 2.0, and 3.0 cm width and six 1 cm thick strips inclined at 0, 30, 45, 60, 90, and -90 degrees with respect to the axial direction. Recovery coefficients for different object sizes and simulated 1 cm thick myocardium inclined at different angles canmore » be obtained from a single scan. Adequacy of axial sampling can be observed visually by creating the long axis view of the phantom.« less

Impact of charcoal waste application on the soil organic matter content and composition of an Haplic Cambisol from South Brazil

NASA Astrophysics Data System (ADS)

dos Anjos Leal, Otávio; Pinheiro Dick, Deborah; Cylene Lombardi, Kátia; Gonçalves Maciel, Vanessa

2014-05-01

In some regions in Brazil, charcoal is usually applied to the soil with the purpose to improve its fertility and its organic carbon (SOC) content. In Brazil, the use of charcoal waste from steel industry with agronomic purposes represents also an alternative and sustainable fate for this material. In this context, the objective of this work was to evaluate the impact of Eucalyptus charcoal waste application on the SOC content and on the soil organic matter (SOM) composition. Increasing doses of charcoal (0, 10, 20 and 40 Mg ha-1) were applied to an Haplic Cambisol, in Irati, South-Brazil. Charcoal was initially applied on the soil surface, and then it was incorporated at 10 cm with a harrow. Soil undisturbed and disturbed samples (four replicates) were collected in September 2011 (1 y and 9 months) after charcoal incorporation. Four soil depths were evaluated (0-5, 5-10, 10-20 and 20-30 cm) and each replicate was composed by three subsamples collected within each plot. The soil samples were air dried, passed through a 9.51 mm sieve and thereafter through a 2.00 mm sieve. The SOC content and total N were quantified by dry combustion. The SOM was concentrated with fluoridric acid 10% and then the SOM composition was evaluated by thermogravimetric analysis along the soil profile. The main impact of charcoal application occurred at the 0-5 cm layer of the area treated with the highest dose: SOC content increased in 15.5 g kg-1 in comparison to the soil without charcoal application. The intermediary doses also increased the SOC content, but the differences were not significant. No differences for N content were found in this soil depth. Further results were observed in the 10-20 cm soil depth, where the highest dose increased the SOC content and N content. Furthermore, this treatment increased the recalcitrance of the SOM, mainly at the 0-5 cm and 10-20 cm soil layers. No differences between doses of charcoal application were found in the 20-30 cm soil depth, suggesting that the charcoal has not migrated so deep in soil even after almost two years of its incorporation.

Silicon anode materials with ultra-low resistivity from the inside out for lithium ion batteries

NASA Astrophysics Data System (ADS)

Xu, Guojun; Jin, Chenxin; Liu, Liekai; Lan, Yu; Yue, Zhihao; Li, Xiaomin; Sun, Fugen; Huang, Haibin; Zhou, Lang

2017-12-01

Broken silicon (Si) wafers with electrical resistivity of 1 and 0.001 Ω cm were respectively ball-milled to Si particles with median diameters of less than 1 μm. Both these two types of Si particles were deposited with silver (Ag) nanoparticles by self-selective electroless deposition method. 1-Ω cm-Si particles, 0.001-Ω cm-Si particles, Ag-deposited 1-Ω cm-Si particles and Ag-deposited 0.001-Ω cm-Si particles were, respectively, mixed with graphite particles in weight ratio of 1:9 to form four types of Si-C anode materials and then they were assembled into coin cells. The experimental results indicate that the Ag-deposited 0.001-Ω cm-Si sample shows the higher capacity, better rate and cycle performance than other three samples, due to the high conductivity of Ag-deposited 0.001-Ω cm-Si sample from the inside out. At the current density of 750 mA g-1, the discharge capacity gap of Ag-deposited 0.001-Ω cm-Si sample and 0.001-Ω cm-Si sample is as high as 141.7 mA h g-1, which is almost equal to the discharge capacity of the latter. Besides, the discharge capacity retention ratio of Ag-deposited 0.001-Ω cm-Si sample after 50 cycles is 70%, which is 23.5% higher than that of 0.001-Ω cm-Si sample.

Induction of secondary metabolite production by UV-C radiation in Vitis vinifera L. Öküzgözü callus cultures.

PubMed

Cetin, Emine Sema

2014-09-04

The aim of the present work was to examine the role of UV-C irradiation on the production of secondary metabolites (total phenolic, total flavanols, total flavonols, catechin, ferulic acid and trans-resveratrol in phenolic compounds and α-, β-, γ- δ-tocopherols) in callus cultures. Studies on the effects of UV-C treatment on callus culture are seldom and generally focused on UV-B. However UV-C radiation play an important role in accumule secondary metabolites. In this study, callus cultures from Öküzgözü grape cultivar were initiated from leaf petiole explants. Calli formed after 6 weeks on the medium supplemented with 0.5 mg L-1 benzylaminopurine (BA), 0.5 mg L-1 indole acetic acid (IAA) on B5 media. Callus tissues were exposed to UV-C irradiation at 10, 20 and 30 cm distances from the UV source for 5 and 10 minutes and samples were collected at hours 0, 24 and 48. The greatest total phenolic content (155.14 mg 100 g-1) was detected in calli exposed to UV-C for 5 min from 30 cm distance and sampled after 24 h. 24 h and 48 h incubation times, 30 cm and 5 min were the most appropriate combination of UV-C application in total flavanol content. Maximum total flavonol content (7.12 mg 100 g-1) was obtained on 0 h, 5 min and 20 cm combination. The highest (+)- catechin accumulation (8.89 mg g-1) was found in calli with 10 min UV-C application from 30 cm distance and sampled after 48 h. Ferulic acid content increased 6 fold in Öküzgözü callus cultures (31.37 μg g-1) compared to the control group. The greatest trans-resveratrol content (8.43 μg g-1) was detected in calli exposed to UV-C for 5 min from 30 cm distance and sampled after 24 h. The highest α-tocopherol concentration was found in calli exposed to UV-C for 10 min from 30 cm distance and sampled after 24 h. As a conclusion, it was showed that UV-C radiation had remarkable promoting effects on the accumulation of secondary metabolites in the calli of Öküzgözü grape cultivar.

Evolution of size-segregated aerosol mass concentration during the Antarctic summer at Northern Foothills, Victoria Land

NASA Astrophysics Data System (ADS)

Illuminati, Silvia; Bau, Sébastien; Annibaldi, Anna; Mantini, Caterina; Libani, Giulia; Truzzi, Cristina; Scarponi, Giuseppe

2016-01-01

Within the framework of the Italian National Programm for Antarctic Research (PNRA), the first direct gravimetric measurements of size-segregated aerosol fractions were carried out at Faraglione Camp, ˜3-km far from the Italian station "M. Zucchelli" (Terra Nova Bay, Ross Sea), during the 2014-2015 austral summer. A six-stage high-volume cascade impactor with size classes between 10 μm and 0.49 μm, and, in parallel, for comparison purposes, a PM10 high-volume sampler (50% cut-off aerodynamic diameter of 10 μm) were used. A 10-day sampling strategy was adopted. Aerosol mass measurements were carried out before and after exposure by using a microbalance specifically designed for the filter weight and placed inside a glove bag in order to maintain stable temperature and humidity conditions during weighing sessions. Measured atmospheric concentrations (referred to the "actual air conditions" of mean temperature of 268 K and mean pressure of 975 hPa) of size-segregated aerosol fractions showed the following values, given as size range, means (interquartile range): Dp < 0.49 μm, 0.33 (0.26-0.34) μg m-3; 0.49-0.95 μm, 0.20 (0.19-0.24) μg m-3; 0.95-1.5 μm, 0.16 (0.13-0.21) μg m-3; 1.5-3.0 μm 0.075 (0.05-0.11) μg m-3; 3.0-7.2 μm 0.12 (0.02-0.19) μg m-3; 7.2-10 μm 0.06 (0.01-0.03) μg m-3. The average mass concentration of the total PM10 at Faraglione Camp for the entire sampling period was 0.92 (0.67-1.1) μg m-3. Although a great variability, the aerosol mass concentration showed a tri-modal distribution, with an accumulation mode (in the range 0.1-1.0 μm) and two coarse modes (CM1 in the range 1.0-3.0 μm, and CM2 in the range 3.0-10 μm). From 50% to 90% of the PM10 mass comes from particles of a size smaller than 1.0 μm. The two coarse modes represented from ˜5% to ˜35% of the PM10, showing opposite seasonal trends (CM1 decreased while CM2 increased). During summer, PM10 mass concentration increased to a maximum of ˜1.6 μg m-3 at mid-December, while in January it decreased to values that are typical of November. Both accumulation and upper super-micron fractions showed a maximum in the same period contributing to the PM10 peak of mid-summer.

Preslaughter diet management in sheep and goats: effects on physiological responses and microbial loads on skin and carcass

PubMed Central

2014-01-01

Sixteen crossbred buck goats (Kiko x Spanish; BW = 32.8 kg) and wether sheep (Dorset x Suffolk; BW = 39.9 kg) were used to determine the effect of preslaughter diet and feed deprivation time (FDT) on physiological responses and microbial loads on skin and carcasses. Experimental animals were fed either a concentrate (CD) or a hay diet (HD) for 4 d and then deprived of feed for either 12-h or 24-h before slaughter. Blood samples were collected for plasma cortisol and blood metabolite analyses. Longisimus muscle (LM) pH was measured. Skin and carcass swabs were obtained to assess microbial loads. Plasma creatine kinase activity (863.9 and 571.7 ± 95.21 IU) and non-esterified fatty acid concentrations (1,056.1 and 589.8 ± 105.01 mEq/L) were different (P < 0.05) between sheep and goats. Species and diet treatments had significant effects on the ultimate pH of LM. Pre-holding total coliform (TCC) and aerobic plate counts (APC) of skin were significantly different between species. Goats had lower (P < 0.05) TCC (2.1 vs. 3.0 log10 CFU/cm2) and APC (8.2 vs. 8.5 log10 CFU/cm2) counts in the skin compared to sheep. Preslaughter skin E. coli counts and TCC were different (P < 0.05) between species. Goats had lower (P < 0.05) counts of E. coli (2.2 vs. 2.9 log10 CFU/cm2) and TCC (2.3 vs. 3.0 log10 CFU/cm2) in the skin compared with those in sheep. Diet, species, and FDT had no effect (P > 0.05) on E. coli and TCC in carcass swab samples. The APC of carcass swab samples were only affected (P < 0.05) by the FDT. The results indicated that preslaughter dietary management had no significant changes on hormone and blood metabolite concentrations and sheep might be more prone for fecal contamination than goats in the holding pens at abattoir. PMID:25343027

Creation of short microwave ablation zones: in vivo characterization of single and paired modified triaxial antennas.

PubMed

Lubner, Meghan G; Ziemlewicz, Tim J; Hinshaw, J Louis; Lee, Fred T; Sampson, Lisa A; Brace, Christopher L

2014-10-01

To characterize modified triaxial microwave antennas configured to produce short ablation zones. Fifty single-antenna and 27 paired-antenna hepatic ablations were performed in domestic swine (N = 11) with 17-gauge gas-cooled modified triaxial antennas powered at 65 W from a 2.45-GHz generator. Single-antenna ablations were performed at 2 (n = 16), 5 (n = 21), and 10 (n = 13) minutes. Paired-antenna ablations were performed at 1-cm and 2-cm spacing for 5 (n = 7 and n = 8, respectively) and 10 minutes (n = 7 and n = 5, respectively). Mean transverse width, length, and aspect ratio of sectioned ablation zones were measured and compared. For single antennas, mean ablation zone lengths were 2.9 cm ± 0.45, 3.5 cm ± 0.55, and 4.2 cm ± 0.40 at 2, 5, and 10 minutes, respectively. Mean widths were 1.8 cm ± 0.3, 2.0 cm ± 0.32, and 2.5 cm ± 0.25 at 2, 5, and 10 minutes, respectively. For paired antennas, mean length at 5 minutes with 1-cm and 2-cm spacing and 10 minutes with 1-cm and 2-cm spacing was 4.2 cm ± 0.9, 4.9 cm ± 1.0, 4.8 cm ± 0.5, and 4.8 cm ± 1.3, respectively. Mean width was 3.1 cm ± 1.0, 4.4 cm ± 0.7, 3.8 cm ± 0.4, and 4.5 cm ± 0.7, respectively. Paired-antenna ablations were more spherical (aspect ratios, 0.72-0.79 for 5-10 min) than single-antenna ablations (aspect ratios, 0.57-0.59). For paired-antenna ablations, 1-cm spacing appeared optimal, with improved circularity and decreased clefting compared with 2-cm spacing (circularity, 0.85 at 1 cm, 0.78 at 2 cm). Modified triaxial antennas can generate relatively short, spherical ablation zones. Paired-antenna ablations were rounder and larger in transverse dimension than single antenna ablations, with 1-cm spacing optimal for confluence of the ablation zone. Copyright © 2014 SIR. Published by Elsevier Inc. All rights reserved.

Growth trends in boys and girls (10-17 years-old) from autonomous region of Madeira, Portugal between 1996-1998 and 2007-2009.

PubMed

Sousa, B; Oliveira, B M P M; de Almeida, M D V

2012-01-01

Growth trends have never been studied in adolescents of the Autonomous Region of Madeira, Portugal. To analyse growth trends in weight, height, body mass index (BMI), waist circumference (WC), mid-upper arm circumference (MUAC) and triceps skin-fold thickness (TST) of adolescents (10-17 years old) of the Autonomous Region of Madeira between 1996-1998 and 2007-2009. A cross-sectional study was carried out between 2007-2009, including 4314 adolescents, 2237 girls and 2077 boys (10-17 years old). To study secular growth trends, data were compared with a sample from 1996-1998, comparing the means for each anthropometric variable by age and sex using the independent-sample t-test. An average increase was found in weight of 5.8 kg in boys and 6.3 kg in girls; in height of 3.0 cm in boys and 3.7 cm in girls; in BMI of 1.5 kg/m(2) in boys and 1.7 kg/m(2) in girls; in WC a difference of 5.6 cm and 4.9 cm for boys and girls, respectively, and for MUAC a difference of 2.7 cm in boys and 2.0 cm in girls. No differences were found in TST in boys, but in girls an increase of 1.2 mm was observed. A general increase in anthropometric measurements, more marked in weight, BMI, WC and MUAC and at younger ages, was observed.

Effect of cryopreservation methods and precryopreservation storage on bottlenose dolphin (Tursiops truncatus) spermatozoa.

PubMed

Robeck, T R; O'Brien, J K

2004-05-01

Research was conducted to develop an effective method for cryopreserving bottlenose dolphin (Tursiops truncatus) semen processed immediately after collection or after 24-h liquid storage. In each of two experiments, four ejaculates were collected from three males. In experiment 1, three cryopreservation methods (CM1, CM2, and CM3), two straw sizes (0.25 and 0.5 ml), and three thawing rates (slow, medium, and fast) were evaluated. Evaluations were conducted at collection, prefreeze, and 0-, 3-, and 6-h postthaw. A sperm motility index (SMI; total motility [TM] x % progressive motility [PPM] x kinetic rating [KR, scale of 0-5]) was calculated and expressed as a percentage MI of the initial ejaculate. For all ejaculates, initial TM and PPM were greater than 85%, and KR was five. At 0-h postthaw, differences in SMI among cryopreservation methods and thaw rates were observed (P < 0.05), but no effect of straw size was observed. In experiment 2, ejaculates were divided into four aliquots for dilution (1:1) and storage at 4 degrees C with a skim milk- glucose or a N-tris(hydroxymethyl)methyl-2-aminoethane sulfonic acid (TES)-TRIS egg yolk solution and at 21 degrees C with a Hepes-Tyrode balanced salt solution (containing bovine albumin and HEPES) (TALP) medium or no dilution. After 24 h, samples were frozen and thawed (CM3, 0.5-ml straws, fast thawing rate) at 20 x 10(6) spermatozoa ml(-1) (low concentration) or at 100 x 10(6) spermatozoa ml(-1) (standard concentration). The SMI at 0-h postthaw was higher for samples stored at 4 degrees C than for samples stored at 21 degrees C (P < 0.001), and at 6-h postthaw, the SMI was higher for samples frozen at the standard concentration than for samples frozen at the low concentration (P < 0.05). For both experiments, acrosome integrity was similar across treatments. In summary, a semen cryopreservation protocol applied to fresh or liquid-stored semen maintained high levels of initial ejaculate sperm characteristics.

Life history of the silvertip shark Carcharhinus albimarginatus from Papua New Guinea

NASA Astrophysics Data System (ADS)

Smart, Jonathan J.; Chin, Andrew; Baje, Leontine; Tobin, Andrew J.; Simpfendorfer, Colin A.; White, William T.

2017-06-01

Growth and maturity of the silvertip shark Carcharhinus albimarginatus from Papua New Guinea were estimated to form the basis of future population assessments. Samples were collected from commercial longline vessels targeting sharks in the Bismarck and Solomon Seas. A total of 48 C. albimarginatus—28 males (95-219 cm total length, TL) and 20 females (116-250 cm TL)—provided data for the analyses. Employing back-calculation techniques accounted for missing juvenile length classes and supplemented the sample size. A multi-model framework incorporating the Akaike information criterion was used to estimate growth parameters. The von Bertalanffy growth function (VBGF) provided the best-fit growth estimates. Parameter estimates were L 0 = 72.1 cm TL, k = 0.04 yr-1 and L ∞ = 311.3 cm TL for males; and L 0 = 70.8 cm TL, k = 0.02 yr-1 and L ∞ = 497.9 cm TL for females. The biologically implausible L ∞ occurred for females as their growth did not asymptote; a typical trait of large shark species. The maximum age estimated from vertebral analysis was 18 yr for both sexes, while the calculated longevity from the VBGF parameters was 27.4 yr for males and 32.2 yr for females. Males matured at 174.7 cm TL and 10.5 yr old, while females matured at 208.9 cm TL and 14.8 yr old.

Production and characterization of a nitrogen-implanted Fe standard to calibrate PIGE measurements

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rodrigues, C. L.; Silva, T. F.; Added, N.

2014-11-11

Three calibration standard was produced by ion implantation of nitrogen in samples of Armco iron (99.7% iron). The samples was irradiated with nitrogen ion beams at several different energies (between 4 keV and 40 keV), and the ion doses were adjusted to obtain an uniform depth profile, using simulations with SRIM code. Two standards, one thick and other a foil (1.62mg/cm{sup 2}), was irradiated at same time with total nominal dose of 6.6×10{sup −16} atoms/cm{sup 2} distributed in a region of 100 nm in depth, with an average concentration of 9.0% nitrogen in iron. The third sample uses the samemore » profile, but with a small dose, 1.1×10{sup −16} atoms/cm{sup 2} and average concentration of 1.5% nitrogen. The characterization of the implanted samples was done using RBS and NRA techniques to quantification of nitrogen.« less

Morphometric study of uninvolved rectal mucosa 10 cm and 20 cm away from the malignant tumor.

PubMed

Despotović, Sanja Z; Milićević, Novica M; Milosević, Dragoslav P; Despotović, Nebojsa; Erceg, Predrag; Bojić, Bozidar; Bojić, Danijela; Svorcan, Petar; Mihajlović, Gordana; Dorđević, Jelena; Lalić, Ivana M; Milićević, Zivana

2014-02-01

Recently, many details of the interplay between tumor cells and tumor-associated stromal elements leading to the progression of malignant disease were elucidated. In contrast, little is known about the role of uninvolved stromal tissue in the remote surrounding of the malignant tumor. Therefore, we performed a computer-aided morphometric study of rectal mucosa in samples taken 10 cm and 20 cm away from the malignant tumor during endoscopic examination of 23 patients older than 60 years. The samples of rectal mucosa from 10 healthy persons of corresponding age subjected to diagnostic rectoscopy during active screening for asymptomatic cancer were used as control. All structural elements of the rectal mucosa were studied and the number of nucleated cells in the lamina propria per 0.1 mm² of tissue was assessed. Our study revealed a reduced number of cells in the lamina propria of the rectal mucosa 10 cm and 20 cm away from the tumor lesion in both male and female patients. The decreased mucosal height and increased crypt number were registered in female patients 10 cm away from the tumor. The connective tissue of lamina propria showed a disorderly organization: the collagen fibers were frail, loosely arranged and signs of tissue edema were present. Small blood vessels and capillaries were much more frequently seen than in healthy tissue. Our results demonstrate the complex interactions between the cancer and remote mucosal tissue of the affected organ.

Response of soil fauna to simulated nitrogen deposition: a nursery experiment in subtropical China.

PubMed

Xu, Guo-Liang; Mo, Jiang-Ming; Fu, Sheng-Lei; Gundersen, Per; Zhou, Guo-Yi; Xue, Jing-Hua

2007-01-01

We studied the responses of soil fauna to a simulated nitrogen deposition in nursery experimental plots in Subtropical China. Dissolved NH4NO3 was applied to the soil by spraying twice per month for 16 months, starting in January 2003 with treatments of 0, 5, 10, 15 and 30 gN/(m2 x a). Soil fauna was sampled after 6, 9, 13 and 16 months of treatment in three soil depths (0-5 cm, 5-10 cm, 10-15 cm). Soil available N increased in correspondence with the increasing N treatment, whereas soil pH decreased. Bacterial and fungal densities were elevated by the N treatment. Soil fauna increased in the lower nitrogen treatments but decreased in the higher N treatments, which might indicate that there was a threshold around 10 gN/(m2 x a) for the stimulating effects of N addition. The N effects were dependent on the soil depth and sampling time. The data also suggested that the effects of the different N treatments were related to the level of N saturation, especially the concentration of NO3- in the soil.

Variability of reflectance measurements with sensor altitude and canopy type

NASA Technical Reports Server (NTRS)

Daughtry, C. S. T.; Vanderbilt, V. C.; Pollara, V. J.

1981-01-01

Data were acquired on canopies of mature corn planted in 76 cm rows, mature soybeans planted in 96 cm rows with 71 percent soil cover, and mature soybeans planed in 76 cm rows with 100 percent soil cover. A LANDSAT band radiometer with a 15 degree field of view was used at ten altitudes ranging from 0.2 m to 10 m above the canopy. At each altitude, measurements were taken at 15 cm intervals also a 2.0 m transect perpendicular to the crop row direction. Reflectance data were plotted as a function of altitude and horizontal position to verify that the variance of measurements at low altitudes was attributable to row effects which disappear at higher altitudes where the sensor integrate across several rows. The coefficient of variation of reflectance decreased exponentially as the sensor was elevated. Systematic sampling (at odd multiples of 0.5 times the row spacing interval) required fewer measurements than simple random sampling over row crop canopies.

Separation and Enrichment of Gold in Water, Geological and Environmental Samples by Solid Phase Extraction on Multiwalled Carbon Nanotubes Prior to its Determination by Flame Atomic Absorption Spectrometry.

PubMed

Duran, Ali; Tuzen, Mustafa; Soylak, Mustafa

2015-01-01

This study proposes the application of multi-walled carbon nanotubes as a solid sorbent for the preconcentration of gold prior to its flame atomic absorption spectrometry determination. Extraction was achieved by using a glass column (15.0 cm in length and 1.0 cm in diameter). Quantitative recoveries were obtained in the pH range of 2.5-4.0; the elution step was carried out with 5.0 ml of 1.0 mol/L HNO3 in acetone. In the ligand-free study, variables such as pH, eluent type, sample volume, flow rates, and matrix effect were examined for the optimum recovery of gold ions. The gold ions were able to be pre-concentrated by a factor of 150 and their LOD was determined to be 1.71 μg/L. In order to evaluate the accuracy of the developed method, addition-recovery tests were applied for the tap water, mineral water, and sea water samples. Gold recovery studies were implemented using a wet digestion technique for mine and soil samples taken from various media, and this method was also applied for anodic slime samples taken from the factories located in the Kayseri Industrial Zone of Turkey.

Spectrophotometric determination of 4-acetamidophenyl N'-(sulphanilamide) acetate in biological fluids.

PubMed

Shah, Bhavna; Patil, Pravin; Shah, Hirva

2014-01-01

A simple, accurate and low cost spectrophotometric method is proposed for the determination of the synthesized paracetamol derivative; 4-acetamidophenyl N'-(sulphanilamide) acetate (APSA) in biological fluids. The spectrophotometric method is based on a condensation reaction between the alcoholic solution of APSA and acidic solution of p-dimethylaminobenzaldeyde (DPMK) to generate a yellow colored product. The linear range for the determination of APSA was 1-10 µg mL(-1) with molar absorptivity of 3.6877 × 10(4) L mol(-1) cm(-1) and Sandell's sensitivity of 0.001 µg cm-2/0.001 absorbance unit. During the inter-day and intra-day analysis, the relative standard deviation for replicated determination of APSA was found to be less than 2.0% and accuracy was 99.20-101.60% and 99.10-101.30% in blood and urine samples, respectively. There was no interference with commonly used blood and urine sample. The developed spectrophotometric method was successfully applied to assess APSA in biological fluids.

Efficacy of ultra short sub-30 minute incubation of 5-aminolevulinic acid photodynamic therapy in vitro.

PubMed

Koo, Eugene; Austin, Evan; Mamalis, Andrew; Jagdeo, Jared

2017-08-01

The estimated incidence of cutaneous squamous cell carcinoma (SCC) is 700,000 cases per year. In the US, SCC incidence is highest among fair skinned adults older than 50 years of age. Thus, as the population ages, the reported number of SCCs will likely increase in the future. Photodynamic therapy (PDT) is an FDA approved therapy for treatment of actinic keratoses (AKs), a precursor to cutaneous SCC lesions. The FDA approved incubation time of the photosensitizing agent 5-aminolevulinic acid (ALA) is 14-18 hours. Recent studies have investigated short ALA incubation times of 1-3 hours with ALA and PDT demonstrating treatment success. Therefore, the question exists whether ALA incubation periods of less than 30 minutes are efficacious. Herein, we evaluate the efficacy of short ALA incubation periods by measuring apoptosis after 10, 15, and 20 minutes of ALA incubation. AG13145 normal human dermal fibroblasts HDFs were incubated with 10, 15, or 20 minute of ALA at various concentrations (0, 0.05, 0.075, 0.1, 0.25, 0.375, 0.5, 1, and 2 mM). After ALA incubation, samples were treated with 1,000 seconds (16 minutes 40 seconds) of Blu-U fluorescent blue light (417 ± 5 nm) for a fluence of 10 J/cm 2 . Immediately following treatment with blue light, samples were collected and stained for apoptosis and necrosis with annexin-V and 7-aminoactinomycin D (7-AAD), and then analyzed by flow cytometry. HDFs incubated with ALA for 10 minute at 36 °C followed by 10 J/cm 2 of blue light had no statistically significant changes in apoptosis. HDFs incubated with ALA for 15 or 20 minutes at 36 °C followed by 10 J/cm 2 of blue light had statistically significant increases in the percentages of cells positive for apoptosis in the 0.5, 1.0, and 2.0 mM ALA doses (P < 0.05). We found that incubation of ALA for at least 15 minutes followed by 10 J/cm 2 of blue light resulted in a statistically significant increase in apoptosis. Lasers Surg. Med. 49:592-598, 2017. © 2017 Wiley Periodicals, Inc. © 2017 Wiley Periodicals, Inc.

Am I normal? A systematic review and construction of nomograms for flaccid and erect penis length and circumference in up to 15,521 men.

PubMed

Veale, David; Miles, Sarah; Bramley, Sally; Muir, Gordon; Hodsoll, John

2015-06-01

To systematically review and create nomograms of flaccid and erect penile size measurements. Study key eligibility criteria: measurement of penis size by a health professional using a standard procedure; a minimum of 50 participants per sample. samples with a congenital or acquired penile abnormality, previous surgery, complaint of small penis size or erectile dysfunction. Synthesis methods: calculation of a weighted mean and pooled standard deviation (SD) and simulation of 20,000 observations from the normal distribution to generate nomograms of penis size. Nomograms for flaccid pendulous [n = 10,704, mean (SD) 9.16 (1.57) cm] and stretched length [n = 14,160, mean (SD) 13.24 (1.89) cm], erect length [n = 692, mean (SD) 13.12 (1.66) cm], flaccid circumference [n = 9407, mean (SD) 9.31 (0.90) cm], and erect circumference [n = 381, mean (SD) 11.66 (1.10) cm] were constructed. Consistent and strongest significant correlation was between flaccid stretched or erect length and height, which ranged from r = 0.2 to 0.6. relatively few erect measurements were conducted in a clinical setting and the greatest variability between studies was seen with flaccid stretched length. Penis size nomograms may be useful in clinical and therapeutic settings to counsel men and for academic research. © 2014 The Authors. BJU International © 2014 BJU International.

Thermal conductivity of (Np0.20Pu0.50Am0.25Cm0.05)O2-x solid solutions

NASA Astrophysics Data System (ADS)

Nishi, Tsuyoshi; Takano, Masahide; Akabori, Mitsuo; Arai, Yasuo

2013-09-01

The authors prepared the sintered sample of (Np0.20Pu0.50Am0.25Cm0.05)O2-x (2 - x = 1.98, 1.96) solid solution and evaluated the dependence of the thermal conductivity on storage time and temperature. The heat capacity of (Np0.20Pu0.50Am0.25Cm0.05)O1.98 was measured between 324 and 1082 K by a drop calorimetry. The thermal diffusivity of (Np0.20Pu0.50Am0.25Cm0.05)O1.98 was measured when the storage time became 48, 216, 720 and 1584 h and that of (Np0.20Pu0.50Am0.25Cm0.05)O1.96 was measured when the storage time became 0,528 and 1386 h. In this study, the latter sample was annealed at 1423 K in vacuum with background pressure of less than 2.0 × 10-4 Pa just after the measurement on the storage time, 1386 h. The thermal diffusivity of (Np0.20Pu0.50Am0.25Cm0.05)O1.96 just after annealing returned to the values of the storage time, 0 h. This result reveals the thermal recovery behavior by annealing. The thermal conductivity of (Np0.20Pu0.50Am0.25Cm0.05)O2-x was determined from the measured thermal diffusivity, heat capacity and bulk density. The thermal conductivity of (Np0.20Pu0.50Am0.25Cm0.05)O2-x exponentially decreased with increasing storage time. This result suggested that the decrease of the thermal conductivity was attributed to the accumulation of lattice defects caused by self-irradiation. The heat capacity of (Np0.20Pu0.50Am0.25Cm0.05)O1.98 was expressed by Cp (J mol-1 K-1) = 1.7314 × 10-2T + 75.720 - 1.0579 × 106 T-2. The heat capacity at higher than 473 K was almost close to those of stoichiometric actinide dioxide within at least ±5%. The thermal diffusivity of (Np0.20Pu0.50Am0.25Cm0.05)O2-x decreased with increasing storage time in the temperature range from 473 to 573 K. The decrease of the thermal diffusivity was attributed by the lattice defect rapidly accumulated by the α-decay of 244Cm. The thermal diffusivity of (Np0.20Pu0.50Am0.25Cm0.05)O1.96 just after annealing returned to the values of the storage time, 0 h. This result reveals the thermal recovery behavior by annealing. The thermal conductivity of (Np0.20Pu0.50Am0.25Cm0.05)O2-x was smaller than those of PuO2 and (Pu0.91Cm0.09)O2 mainly because of the oxygen vacancies as is seen other actinide dioxide, such as mixed oxide (MOX) fuels.

Does peripheral quantitative computed tomography ignore tissue density of cancellous bone?

PubMed

Banse, X; Devogelaer, J P

2002-01-01

The purpose of this work was to determine the capacity of peripheral quantitative computed tomography (pQCT) to accurately measure the true physical properties of vertebral cancellous bone samples and to predict their stiffness. pQCT bone mineral density (BMD) was first measured in ideal conditions. Ten cubic specimens of vertebral cancellous bone (10 x 10 x 10 mm) were washed with a water jet, defatted, and scanned in saline after elimination of air bubbles; thirteen slices were obtained. Seventy-one unprepared cylindrical samples were scanned in more realistic conditions, which allow further biomechanical testing. After extraction from the vertebral body, the samples were pushed into a plastic tube (no effort was made to remove the marrow or air bubbles), and only four slices were obtained to reduce the duration of scan. For the 81 samples, the true bone volume fraction (BV/TV, %), true apparent density (rho(app), g/cm(3)), and tissue density (rho(tiss), g/cm(3)) (an indicator of the degree of mineralization of the matrix) were then measured using Archimedes principle. rho(app) was closely correlated to BV/TV (r(2) = 0.97). rho(tiss) (1.58 +/- 0.08 g/cm(2)) was almost constant but had some influence on rho(app) (r(2) = 0.03, p < 0.001). The pQCT BMD predicted accurately rho(app) (r(2) = 0.96) and BV/TV (r(2) = 0.93) for the cylinders. For the cubes, in ideal conditions, the same correlations were even better (r(2) > 0.99, both). Analysis of covariance indicated no difference (p > 0.05) in the regressions due to preparation of the samples. The stiffness was better predicted by the true rho(app) (r(2) = 0.87) than by BV/TV (r(2) = 0.83), indicating that stiffness was influenced by small differences in the tissue density. Consequently, the correlation between pQCT BMD and stiffness was excellent (r(2) = 0.84). The fact that pQCT did not ignore this tissue density information compensated for the inaccuracies linked to realistic scanning conditions of the cylinder.

Implementation of a Shallow Groundwater Temperature Manipulation: Linking Hydrogeology, Biogeochemistry, and Aquatic Ecology

NASA Astrophysics Data System (ADS)

Wilson, K. P.; Williams, D. D.

2004-05-01

Integration of the fields of hydrogeology, biogeochemistry, and meiofaunal and microbial ecology is being used for a shallow groundwater temperature manipulation which simulates global climate change predictions. This study is being conducted on a first order spring-stream, Valley Spring, (southern Ontario, Canada) the headwater of which has been longitudinally divided to a sediment depth of -100 cm. To examine groundwater flow paths and hydraulic conductivity, and to collect physicochemical parameters and nutrient samples, a series of nested piezometers have been installed along three transects across the stream channel. Each nest evaluates water characteristics at depths of -20, -40, -60, -80, and -100 cm. Meiofaunal and microbial samples are collected, using a standpipe corer at the same depths as the piezometer openings. Sampling started in June 2002 and heating of one side of the groundwater began in March 2004. Hydraulic conductivity is heterogeneous with depth ranging from 0.0004 cm/s at -20 cm to 0.00002 cm/s at -100cm, but relatively uniform laterally, ranging from 0.0004 cm/s at 1 m to 0.0003 cm/s at 3 m from the stream channel. Pre-manipulation water temperatures decrease with depth in the summer, ranging from 14.5° C at the surface to 12.5° C at -100 cm. In contrast, temperature increases from 13.1 at the surface to 14.5° C at -100 cm in the fall. Temperature during the winter and spring are within 1.0° C from the surface to -100 cm, but range from 9.0-9.5° C in the winter and 8.0-7.0° C in the spring, respectively. Pre-manipulation nitrate concentrations are higher in winter (0.45 mg/l) then in summer (0.28 mg/l) and decrease with depth. Ammonia shows an inverse relationship, with lower concentrations in winter than summer (0.19 and 0.32 mg/l, respectively) and increase with depth. Dissolved organic carbon (DOC) also shows an increase with depth, ranging from 1.6 mg/l at the surface to 6.23 mg/l at -100 cm. Pre-manipulation meiofaunal abundance shows no difference between seasons but higher densities at -20cm then at all other depths. The most common meiofaunal taxa include Harpacticoida, Nematoda, Ostracoda, Chironomidae, Collembola, and Hydracarina. Plecoptera and Hymenoptera larvae are also found on occasion above -60 cm.

Transport properties of undoped and Br-doped PbTe sintered at high-temperature and pressure >=4.0 GPa

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dong, Yongkwan; McGuire, Michael A.; Malik, Abds-Sami, E-mail: abds-sami.malik@diamondinnovations.co

2009-10-15

The thermoelectric properties of nominally undoped PbTe and Br doped PbTe materials sintered at high-pressure and high-temperature (HPHT) have been studied. All samples show n-type semiconducting behavior with negative thermopower. For undoped PbTe, four different HPHT treatments were performed at pressures between 4.0 and 6.5 GPa. PbTe doped with Br at 0.5, 1.0, 2.0, 3.0x10{sup 19} cm{sup -3} was HPHT treated at 4.0 GPa and 1045 deg. C. As the dopant concentration increases, the absolute thermopower decreases, thermal conductivity increases, and electrical resistivity decreases. At a nominal dopant concentration of 1.0x10{sup 19} cm{sup -3}, carrier mobility of 1165 cm{sup 2}/Vmore » s and dimensionless thermoelectric figure-of-merit, ZT, of around 0.27 at 300 K were obtained. These results demonstrate that HPHT post-processing is a viable and controllable way of tuning the thermoelectric properties of PbTe-based materials. - Abstract: The effect, on thermoelectric properties, of sintering undoped and Br doped PbTe at pressures >=4.0 GPa and 1045 deg. C are reported and compared with conventionally sintered materials. Display Omitted« less

Raman spectra and cross sections of ammonia, chlorine, hydrogen sulfide, phosgene, and sulfur dioxide toxic gases in the fingerprint region 400-1400 cm-1

NASA Astrophysics Data System (ADS)

Aggarwal, R. L.; Farrar, L. W.; Di Cecca, S.; Jeys, T. H.

2016-02-01

Raman spectra of ammonia (NH3), chlorine (Cl2), hydrogen sulfide (H2S), phosgene (COCl2), and sulfur dioxide (SO2) toxic gases have been measured in the fingerprint region 400-1400 cm-1. A relatively compact (<2'x2'x2'), sensitive, 532 nm 10 W CW Raman system with double-pass laser and double-sided collection was used for these measurements. Two Raman modes are observed at 934 and 967 cm-1 in NH3. Three Raman modes are observed in Cl2 at 554, 547, and 539 cm-1, which are due to the 35/35 35/37, and 37/37 Cl isotopes, respectively. Raman modes are observed at 870, 570, and 1151 cm-1 in H2S, COCl2, and SO2, respectively. Values of 3.68 ± 0.26x10-32 cm2/sr (3.68 ± 0.26x10-36 m2/sr), 1.37 ± 0.10x10-30 cm2/sr (1.37 ± 0.10x10-34 m2/sr), 3.25 ± 0.23x10-31 cm2/sr (3.25 ± 0.23x10-35 m2/sr), 1.63 ± 0.14x10-30 cm2/sr (1.63 ± 0.14x10-34 m2/sr), and 3.08 ± 0.22x10-30 cm2/sr (and 3.08 ± 0.22x10-34 m2/sr) were determined for the differential Raman cross section of the 967 cm-1 mode of NH3, sum of the 554, 547, and 539 cm-1 modes of Cl2, 870 cm-1 mode of H2S, 570 cm-1 mode of COCl2, and 1151 cm-1 mode of SO2, respectively, using the differential Raman cross section of 3.56 ± 0.14x10-31 cm2/sr (3.56 ± 0.14x10-35 m2/sr) for the 1285 cm-1 mode of CO2 as the reference.

Interface and transport properties of metallization contacts to flat and wet-etching roughed N-polar n-type GaN.

PubMed

Wang, Liancheng; Liu, Zhiqiang; Guo, Enqing; Yang, Hua; Yi, Xiaoyan; Wang, Guohong

2013-06-26

The electrical characteristics of metallization contacts to flat (F-sample, without wet-etching roughed) and wet-etching roughed (R-sample) N-polar (Nitrogen-polar) n-GaN have been investigated. R-sample shows higher contact resistance (Rc) to Al/Ti/Au (~2.5 × 10(-5) Ω·cm(2)) and higher Schottky barriers height (SBH, ~0.386 eV) to Ni/Au, compared with that of F-sample (~1.3 × 10(-6) Ω·cm(2), ~0.154 eV). Reasons accounting for this discrepancy has been detail investigated and discussed: for R-sample, wet-etching process caused surface state and spontaneous polarization variation will degraded its electrical characteristics. Metal on R-sample shows smoother morphology, however, the effect of metal deposition state on electrical characteristics is negligible. Metallization contact area for both samples has also been further considered. Electrical characteristics of metallization contact to both samples show degradation upon annealing. The VLED chip (1 mm × 1 mm), which was fabricated on the basis of a hybrid scheme, coupling the advantage of F- and R-sample, shows the lowest forward voltage (2.75 V@350 mA) and the highest light output power.

Rapid, quantitative analysis of ppm/ppb nicotine using surface-enhanced Raman scattering from polymer-encapsulated Ag nanoparticles (gel-colls).

PubMed

Bell, Steven E J; Sirimuthu, Narayana M S

2004-11-01

Rapid, quantitative SERS analysis of nicotine at ppm/ppb levels has been carried out using stable and inexpensive polymer-encapsulated Ag nanoparticles (gel-colls). The strongest nicotine band (1030 cm(-1)) was measured against d(5)-pyridine internal standard (974 cm(-1)) which was introduced during preparation of the stock gel-colls. Calibration plots of I(nic)/I(pyr) against the concentration of nicotine were non-linear but plotting I(nic)/I(pyr) against [nicotine](x)(x = 0.6-0.75, depending on the exact experimental conditions) gave linear calibrations over the range (0.1-10 ppm) with R(2) typically ca. 0.998. The RMS prediction error was found to be 0.10 ppm when the gel-colls were used for quantitative determination of unknown nicotine samples in 1-5 ppm level. The main advantages of the method are that the gel-colls constitute a highly stable and reproducible SERS medium that allows high throughput (50 sample h(-1)) measurements.

[Seasonal dynamics of soil organic carbon mineralization for two forest types in Xiaoxing'an Mountains, China].

PubMed

Gao, Fei; Lin, Wei; Cui, Xiao-yang

2016-01-01

To investigate the seasonal dynamics of soil organic carbon (SOC) mineralization in Xiaoxing'an Mountain, we incubated soil samples collected from virgin Korean pine forest and broad-leaved secondary forest in different seasons in the laboratory and measured the SOC mineralization rate and cumulative SOC mineralization (Cm). We employed simultaneous reaction model to describe C mineralization kinetics and estimated SOC mineralization parameters including soil easily mineralizable C (C1), potentially mineralizable C (C₀). We also analyzed the relations between Cm, C₁and their influencing factors. Results showed that the incubated SOC mineralization rate and Cm for 0-5 cm soil layer decreased from early spring to late autumn, while for 5-10 cm soil layer the seasonal variation was not statistically significant for both forest types. The C₁ in 0-5 and 5-10 cm soil layers varied from 42.92-92.18 and 19.23-32.95 mg kg⁻¹, respectively, while the C₀ in 0-5 and 5-10 cm soil layers varied from 863.92-3957.15 and 434.15-865.79 mg · kg⁻¹, respec- tively. Both C₁ and C₀ decreased from early spring to late autumn. The proportions of C₀ in SOC for two forest types were 0.74%-2.78% and 1.11%-1.84% in 0-5 and 5-10 cm soil layers, respectively, and decreased from early spring to late autumn, indicating that SOC tended to become more stable as a whole from spring to autumn. The Cm and C₀ were significantly positively correlated to in situ soil water content and hot water-extractable carbohydrate content, but were not correlated to in situ soil temperature and cool water-extractable carbohydrate content. We concluded that soil labile organic carbon, soil physical and chemical properties contributed to the seasonal dynamics of SOC mineralization in the forests.

Evaluation of Chemical Warfare Agent Wipe Sampling ...

EPA Pesticide Factsheets

Report This investigation tested specific (CWAs), including sarin (GB), soman (GD), cyclosarin (GF), sulfur mustard (HD), and O-ethyl-S-(2-diisopropylaminoethyl) methylphosphonothioate (VX) on the non-ideal (e.g., porous and permeable) surfaces of drywall, vinyl tile, wood, laminate, and coated glass. Pesticides (diazinon and malathion) were used so that a comparison is possible with existing literature data (1). Experiments included testing with coupons having surface areas of 10 cm2 and 100 cm2. The 10-cm2 coupons were of a size that could easily be extracted in a 2 oz jar (to provide comparative data for CWA recoveries generated by direct extraction) and the 100-cm2 coupons better represented the area of a surface that might typically be sampled by wipe extraction. In addition, CWA, at a normalized surface concentration of 0.1 µg per cm2 surface area, were spiked on coupons of the tested surfaces. Wipes were wetted with either dichloromethane (DCM) or isopropanol (IPA) before sampling for CWA. Experimental parameters include multiple wipe types, porous/permeable surfaces, coupon surface area, solvent used to wet the wipe (i.e., wetting solvent), and the utility of VX-d14 as an extracted internal standard.

Efficacy of a Blend of Sulfuric Acid and Sodium Sulfate against Shiga Toxin-Producing Escherichia coli, Salmonella, and Nonpathogenic Escherichia coli Biotype I on Inoculated Prerigor Beef Surface Tissue.

PubMed

Scott-Bullard, Britteny R; Geornaras, Ifigenia; Delmore, Robert J; Woerner, Dale R; Reagan, James O; Morgan, J Bred; Belk, Keith E

2017-12-01

A study was conducted to investigate the efficacy of a sulfuric acid-sodium sulfate blend (SSS) against Escherichia coli O157:H7, non-O157 Shiga toxin-producing E. coli (STEC), Salmonella, and nonpathogenic E. coli biotype I on prerigor beef surface tissue. The suitability of using the nonpathogenic E. coli as a surrogate for in-plant validation studies was also determined by comparing the data obtained for the nonpathogenic inoculum with those for the pathogenic inocula. Prerigor beef tissue samples (10 by 10 cm) were inoculated (ca. 6 log CFU/cm 2 ) on the adipose side in a laboratory-scale spray cabinet with multistrain mixtures of E. coli O157:H7 (5 strains), non-O157 STEC (12 strains), Salmonella (6 strains), or E. coli biotype I (5 strains). Treatment parameters evaluated were two SSS pH values (1.5 and 1.0) and two spray application pressures (13 and 22 lb/in 2 ). Untreated inoculated beef tissue samples served as controls for initial bacterial populations. Overall, the SSS treatments lowered inoculated (6.1 to 6.4 log CFU/cm 2 ) bacterial populations by 0.6 to 1.5 log CFU/cm 2 (P < 0.05), depending on inoculum type and recovery medium. There were no main effects (P ≥ 0.05) of solution pH or spray application pressure when SSS was applied to samples inoculated with any of the tested E. coli inocula; however, solution pH did have a significant effect (P < 0.05) when SSS was applied to samples inoculated with Salmonella. Results indicated that the response of the nonpathogenic E. coli inoculum to the SSS treatments was similar (P ≥ 0.05) to that of the pathogenic inocula tested, making the E. coli biotype I strains viable surrogate organisms for in-plant validation of SSS efficacy on beef. The application of SSS at the tested parameters to prerigor beef surface tissue may be an effective intervention for controlling pathogens in a commercial beef harvest process.

Dielectric and ferroelectric properties of Ba0.87Ca0.10La0.03Ti1-xSnxO3 lead-free ceramics

NASA Astrophysics Data System (ADS)

Chen, Zhi-hui; Li, Zhi-wei; Fang, Chang; Qiu, Jian-hua; Ding, Jian-ning; Zhu, Wei-qin; Xu, Jiu-jun

2017-12-01

Ba0.87Ca0.10La0.03Ti1-xSnxO3 (BCLTS) piezoelectric lead-free ceramics were fabricated by conventional solid-state sintering process at 1480 °C. The effects of Sn4+ substitution on microstructure and electrical properties of the ceramics were researched. All samples show a pure perovskite structure with no secondary phase, and the coexistence of orthorhombic phase and tetragonal phase in the composition range of x = 0.06-0.10 is identified in the XRD pattern. Average grain size decreases with the increase of Sn content in the BCLTS samples. The BCLTS ceramics exhibit excellent piezoelectric properties and ferroelectric properties with d33 = 501pC/N and kp = 45.6% at x = 0.10, and Pr = 9.87 μC/cm2 at x = 0.06. The analysis on the temperature dependence of dielectric permittivity approved the diffuse relaxor ferroelectric feature for all the BCLTS samples.

Hydraulic properties of coarsely and finely ground woodchips

NASA Astrophysics Data System (ADS)

Subroy, Vandana; Giménez, Daniel; Qin, Mingming; Krogmann, Uta; Strom, Peter F.; Miskewitz, Robert J.

2014-09-01

Recent evidence suggests that leachate from woodchips stockpiled at recycling facilities could negatively impact water quality. Models that can be used to simulate water movement/leachate production require information on water retention and hydraulic conductivity functions of the stockpiled material. The objectives of this study were to (1) determine water retention and hydraulic conductivity functions of woodchips with particle size distributions (PSDs) representative of field stockpiled material by modeling multistep outflow and (2) assess the performance of three pore structure models for their ability to simulate outflow. Six samples with contrasting PSDs were assessed in duplicate. Samples were packed in cylindrical columns (15.3 cm high, 12.1 cm wide) to measure saturated hydraulic conductivity (Ks), cumulative outflow and water content at equilibrium with pressure potentials of -2, -10 and -40 cm. Water retention at pressure potentials between -200 and -10,000 cm were obtained using pressure plate extractors and used to supplement data from the outflow experiment. Hydraulic parameters of the pore models were derived from these measurements using HYDRUS-1D run by DREAM(ZS). Ks was independent of PSD with values between 55 and 80 cm/h. Cumulative outflow at each pressure potential was correlated with the PSD geometric mean diameters, and was best predicted by a model having two interacting pore domains, each with separate hydraulic conductivity and water retention functions (DPeM). Unsaturated conductivities were predicted to drop on an average to 0.24 cm/h at -10 cm and 3 × 10-3 cm/h at -50 cm for the DPeM model, suggesting that water would move slowly through stockpiles except during intense rainfalls.

Direct nano-patterning of graphene with helium ion beams

DOE Office of Scientific and Technical Information (OSTI.GOV)

Naitou, Y., E-mail: yu-naitou@aist.go.jp; Iijima, T.; Ogawa, S.

2015-01-19

Helium ion microscopy (HIM) was used for direct nano-patterning of single-layer graphene (SLG) on SiO{sub 2}/Si substrates. This technique involves irradiation of the sample with accelerated helium ions (He{sup +}). Doses of 2.0 × 10{sup 16 }He{sup + }cm{sup −2} from a 30 kV beam induced a metal-insulator transition in the SLG. The resolution of HIM patterning on SLG was investigated by fabricating nanoribbons and nanostructures. Analysis of scanning capacitance microscopy measurements revealed that the spatial resolution of HIM patterning depended on the dosage of He{sup +} in a non-monotonic fashion. Increasing the dose from 2.0 × 10{sup 16} to 5.0 × 10{sup 16 }He{sup + }cm{sup −2} improved the spatialmore » resolution to several tens of nanometers. However, doses greater than 1.0 × 10{sup 17 }He{sup + }cm{sup −2} degraded the patterning characteristics. Direct patterning using HIM is a versatile approach to graphene fabrication and can be applied to graphene-based devices.« less

Neutron-capture Cl-36, Ca-41, Ar-36, and Sm-150 in large chondrites: Evidence for high fluences of thermalized neutrons

NASA Technical Reports Server (NTRS)

Bogard, D. D.; Nyquist, L. E.; Bansal, B. M.; Garrison, D. H.; Wiesmann, H.; Herzog, G. F.; Albrecht, A. A.; Vogt, S.; Klein, J.

1995-01-01

We have measured significant concentrations of Cl-36, Ca-41, Ar-36 from decay of Cl-36, and Sm-150 produced from the capture of thermalized neutrons in the large Chico L6 chondrite. Activities of Cl-36 and Ca-41, corrected for a high-energy spallogenic component and a terrestrial age of approximately 50 ka, give average neutron-capture production rates of 208 atoms/min/g-Cl and 1525 atoms/min/kg-Ca, which correspond to thermal neutron (n) fluxes of 6.2 n/sq cm/s and 4.3 n/sq cm/s, respectively. If sustained for the approximately 65 Ma single-stage, cosmic ray exposure age of Chico, these values correspond to thermal neutron fluences of approximately 1.3 x 10(exp 16) and 0.8 x 10(exp 16) n/sq cm for Cl-36 and Ca-41, respectively. Stepwise temperature extraction of Ar in Chico impact melt shows Ar-36/Ar-38 ratios as large as approximately 9. The correlation of high Ar-36/Ar-38 with high Cl/Ca phases in neutron-irradiated Chico indicates that the excess Ar-36 above that expected from spallation is due to decay of neutron-produced Cl-36. Excess Ar-36 in Chico requires a thermal neutron fluence of 0.9-1.7 x 10(exp 16) n/sq cm. Decreases in Sm-149/Sm-152 due to neutron-capture by Sm-149 correlate with increases in Sm-150/Sm-152 for three samples of Chico, and one of the Torino H-chondrite. The 0.08% decrease in Sm-149 shown by Chico corresponds to a neutron fluence of 1.23 x 10(exp 16) n/sq cm. This fluence derived from Sm considers capture of epithermal neutrons and effects of chemical composition on the neutron energy distribution. Excess Ar-36 identified in the Arapahoe, Bruderheim, and Torino chondrites and the Shallowater aubrite suggest exposure to neutron fluences of approximately 0.2-0.2 x 10(exp 16) n/sq cm. Depletion of Sm-149 in Torino and the LEW86010 angrite suggest neutron fluences of 0.8 x 10(exp 16) n/sq cm and 0.25 x 10(exp 16) n/sq cm, respectively. Neutron fluences of approximately 10(exp 16) n/sq cm in Chico are almost as large as those previously observed for some lunar soils. Consideration of exposure ages suggests that the neutron flux in Chico may have been greater than that in many lunar soils.

Synthesis and Characterization Materials M-Barium Hexaferrite Doping Ions Co-Mn Nano Particle

NASA Astrophysics Data System (ADS)

Susilawati; Doyan, A.; Sahlam

2017-05-01

This research has been success in the synthesis of M-Barium hexaferrite (BaM) doping Co-Mn ions using coprecipitation method are expected to be applied as a base material in the coating RADAR. M-Barium hexaferrite (BaM) are BaFe12-2xCoxMnxO19 synthesized with various concentrations (x = 0.0, 0.1, 0.2, 0.3) and the calcinations temperature (T = 400°C, 600°C, 800°C). The materials characterization using a X-Ray Diffraction (XRD), Transmission Electron Microscope (TEM), Inductance Capacitance and resistance (LCR) meter, and Vibrating Sample Magnetometer (VSM) Instruments. The measurement results using XRD shows the material has a hexagonal crystalline structure. The measurement results using a TEM show a sample of nano crystal materials with grain diameters up to 40 nm and spacing of the crystal lattice. The measurement results using a LCR-meter shows the electric conductivity of 1.15 × 10-6 S/cm to BaM without doping, 3.75 × 10-6 S/cm to 0.1 doping concentration calcination temperature of 400 °C, and 1,23 × 10-5 S/cm to 0.3 doping concentration calcination temperature of 800 °C, thus including semiconductor materials. The magnetic properties of materials using a VSM test results show the value of coercivity of 0.1 T; remanence value of 0.06 emu/g; and the saturation value of 0.42 emu/g. The results above show BaM Co-Mn metal doping potential as anti-radar material.

Investigation of the effect of power ultrasound on the nucleation of water during freezing of agar gel samples in tubing vials.

PubMed

Kiani, Hossein; Sun, Da-Wen; Delgado, Adriana; Zhang, Zhihang

2012-05-01

Nucleation, as an important stage of freezing process, can be induced by the irradiation of power ultrasound. In this study, the effect of irradiation temperature (-2 °C, -3 °C, -4 °C and -5 °C), irradiation duration (0s, 1s, 3s, 5s, 10s or 15s) and ultrasound intensity (0.07 W cm(-2), 0.14 W cm(-2), 0.25 W cm(-2), 0.35 W cm(-2) and 0.42 W cm(-2)) on the dynamic nucleation of ice in agar gel samples was studied. The samples were frozen in an ethylene glycol-water mixture (-20 °C) in an ultrasonic bath system after putting them into tubing vials. Results indicated that ultrasound irradiation is able to initiate nucleation at different supercooled temperatures (from -5 °C to -2 °C) in agar gel if optimum intensity and duration of ultrasound were chosen. Evaluation of the effect of 0.25 W cm(-2) ultrasound intensity and different durations of ultrasound application on agar gels showed that 1s was not long enough to induce nucleation, 3s induced the nucleation repeatedly but longer irradiation durations resulted in the generation of heat and therefore nucleation was postponed. Investigation of the effect of ultrasound intensity revealed that higher intensities of ultrasound were effective when a shorter period of irradiation was used, while lower intensities only resulted in nucleation when a longer irradiation time was applied. In addition to this, higher intensities were not effective at longer irradiation times due to the heat generated in the samples by the heating effect of ultrasound. In conclusion, the use of ultrasound as a means to control the crystallization process offers promising application in freezing of solid foods, however, optimum conditions should be selected. Copyright © 2011 Elsevier B.V. All rights reserved.

Is there an association between airborne and surface microbes in the critical care environment?

PubMed

Smith, J; Adams, C E; King, M F; Noakes, C J; Robertson, C; Dancer, S J

2018-04-09

There are few data and no accepted standards for air quality in the intensive care unit (ICU). Any relationship between airborne pathogens and hospital-acquired infection (HAI) risk in the ICU remains unknown. First, to correlate environmental contamination of air and surfaces in the ICU; second, to examine any association between environmental contamination and ICU-acquired staphylococcal infection. Patients, air, and surfaces were screened on 10 sampling days in a mechanically ventilated 10-bed ICU for a 10-month period. Near-patient hand-touch sites (N = 500) and air (N = 80) were screened for total colony count and Staphylococcus aureus. Air counts were compared with surface counts according to proposed standards for air and surface bioburden. Patients were monitored for ICU-acquired staphylococcal infection throughout. Overall, 235 of 500 (47%) surfaces failed the standard for aerobic counts (≤2.5 cfu/cm 2 ). Half of passive air samples (20/40: 50%) failed the 'index of microbial air' contamination (2 cfu/9 cm plate/h), and 15/40 (37.5%) active air samples failed the clean air standard (<10 cfu/m 3 ). Settle plate data were closer to the pass/fail proportion from surfaces and provided the best agreement between air parameters and surfaces when evaluating surface benchmark values of 0-20 cfu/cm 2 . The surface standard most likely to reflect hygiene pass/fail results compared with air was 5 cfu/cm 2 . Rates of ICU-acquired staphylococcal infection were associated with surface counts per bed during 72h encompassing sampling days (P = 0.012). Passive air sampling provides quantitative data analogous to that obtained from surfaces. Settle plates could serve as a proxy for routine environmental screening to determine the infection risk in ICU. Copyright © 2018 The Healthcare Infection Society. Published by Elsevier Ltd. All rights reserved.

Electrical properties and x-ray photoelectron spectroscopy studies of Bi(Zn0.5Ti0.5)O3 doped Pb(Zr0.4Ti0.6)O3 thin films

NASA Astrophysics Data System (ADS)

Tang, M. H.; Zhang, J.; Xu, X. L.; Funakubo, H.; Sugiyama, Y.; Ishiwara, H.; Li, J.

2010-10-01

(1-x)Pb(Zr0.4,Ti0.6)O3-(x)Bi(Zn0.5,Ti0.5)O3 (PZT-BZT) (x =0, 0.03, 0.05, 0.08, and 0.1) films were deposited on Pt(111)/Ti/SiO2/Si(100) substrates by chemical solution deposition using spin-coating. All samples showed highly (111) oriented perovskite phase and no other phase was observed. The ferroelectric properties of PZT-BZT films were systematically investigated as a function of the content x of the BZT solution. It is found that BZT doping in PZT films could greatly enhance the remnant polarization (Pr), as well as improve the fatigue property. In a 3 wt % BZT-doped PZT film, the 2Pr and the coercive field (Ec) are 90 μC/cm2 and 95 kV/cm at 10 kHz, respectively, at an electric field of 500 kV/cm, and the leakage current density is less than 1×10-7 A/cm2. The impact of BZT doping on the structure of PZT has been investigated by x-ray photoelectron spectroscopy.

Bonding of human meniscal and articular cartilage with photoactive 1,8-naphthalimide dyes

NASA Astrophysics Data System (ADS)

Judy, Millard M.; Nosir, Hany R.; Jackson, Robert W.; Matthews, James Lester; Lewis, David E.; Utecht, Ronald E.; Yuan, Dongwu

1996-05-01

This study focused on meniscal cartilage repair by using the laser-activated photoactive 1,8- naphthalimide dye N,N'-bis-{6-[2-(2-(2- aminoethoxy)ethoxy)ethoxyethyl]amino-1H-benz (de)isoquinolin-1,3(2H)-dion-2- yl}-1,11-diamino-3,6,9-trioxaundecane. Harvested cadaveric human menisci were debrided and carved into strips 1 mm thick, 10 mm long, and 3 mm wide. Each strip was divided into two flaps, the surface painted with photoactive dye, the painted surfaces overlapped, the sample wrapped in Saran film, and the composite sandwiched between two glass slides at a pressure of approximately 3 kg/cm2. The sample then was transilluminated by argon ion laser light of 457.9-nm wavelength at a power density of 200 mW/cm2 with exposure times up to 5 h (3902 J/cm2 energy density). Essentially, the same procedures were performed for human femoral articular cartilage samples. Control experiments were conducted with laser irradiation alone and with dye alone. All the specimens were stored in isotonic saline solution for 2 h after irradiation to ensure hydration. The bond shear-strength was then tested and samples prepared for optical and electron transmission microscopy. Shear strength values of up to 1.8 kg/cm2 for meniscal tissues and 1.2 kg/cm2 for articular cartilaginous tissues were obtained for exposures of 3902 J/cm2. Shear strength values of approximately 0.9 kg/cm2 and 0.4 kg/cm2, respectively, for meniscus and cartilage were obtained with 459 J/cm2 exposure. Dye- and light-only controls exhibited 0 kg/cm2 shear strength values. Microscopy revealed close contact at the bonded surface in the laser-activated, dye-treated-specimens. This study shows that the laser-activated photoactive dyes have the capability of athermally bonding the meniscal and articular cartilage surfaces.

Optimization of collision/reaction gases for determination of 90Sr in atmospheric particulate matter by inductively coupled plasma tandem mass spectrometry after direct introduction of air via a gas-exchange device

NASA Astrophysics Data System (ADS)

Suzuki, Yoshinari; Ohara, Ryota; Matsunaga, Kirara

2017-09-01

Nuclear power plant accidents release radioactive strontium 90 (90Sr) into the environment. Monitoring of 90Sr, although important, is difficult and time consuming because it emits only beta radiation. We have developed a new analytical system that enables real-time analysis of 90Sr in atmospheric particulate matter with an analytical run time of only 10 min. Briefly, after passage of an air sample through an impactor, a small fraction of the sample is introduced into a gas-exchange device, where the air is replaced by Ar. Then the sample is directly introduced into an inductively coupled plasma tandem mass spectrometry (ICP-MS/MS) system equipped with a collision/reaction cell to eliminate isobaric interferences on 90Sr from 90Zr+, 89Y1H+, and 90Y+. Experiments with various reaction gas conditions revealed that these interferences could be minimized under the following optimized conditions: 1.0 mL min- 1 O2, 10.0 mL min- 1 H2, and 1.0 mL min- 1 NH3. The estimated background equivalent concentration and estimated detection limit of the system were 9.7 × 10- 4 and 3.6 × 10- 4 ng m- 3, respectively, which are equivalent to 4.9 × 10- 6 and 1.8 × 10- 6 Bq cm- 3. Recoveries of Sr in PM2.5 measured by real-time analysis compared to those obtained by simultaneously collection on filter was 53 ± 23%, and using this recovery, the detection limit as PM2.5 was estimated to be 3.4 ± 1.5 × 10- 6 Bq cm- 3. That is, this system enabled detection of 90Sr at concentrations < 5 × 10- 6 Bq cm- 3 even considering the insufficient fusion/vaporization/ionization efficiency of Sr in PM2.5.

Multi-walled carbon nanotubes: sampling criteria and aerosol characterization

PubMed Central

Chen, Bean T.; Schwegler-Berry, Diane; McKinney, Walter; Stone, Samuel; Cumpston, Jared L.; Friend, Sherri; Porter, Dale W.; Castranova, Vincent; Frazer, David G.

2015-01-01

This study intends to develop protocols for sampling and characterizing multi-walled carbon nanotube (MWCNT) aerosols in workplaces or during inhalation studies. Manufactured dry powder containing MWCNT’s, combined with soot and metal catalysts, form complex morphologies and diverse shapes. The aerosols, examined in this study, were produced using an acoustical generator. Representative samples were collected from an exposure chamber using filters and a cascade impactor for microscopic and gravimetric analyses. Results from filters showed that a density of 0.008–0.10 particles per µm2 filter surface provided adequate samples for particle counting and sizing. Microscopic counting indicated that MWCNT’s, resuspended at a concentration of 10 mg/m3, contained 2.7 × 104 particles/cm3. Each particle structure contained an average of 18 nanotubes, resulting in a total of 4.9 × 105 nanotubes/cm3. In addition, fibrous particles within the aerosol had a count median length of 3.04 µm and a width of 100.3 nm, while the isometric particles had a count median diameter of 0.90 µm. A combination of impactor and microscopic measurements established that the mass median aerodynamic diameter of the mixture was 1.5 µm. It was also determined that the mean effective density of well-defined isometric particles was between 0.71 and 0.88 g/cm3, and the mean shape factor of individual nanotubes was between 1.94 and 2.71. The information obtained from this study can be used for designing animal inhalation exposure studies and adopted as guidance for sampling and characterizing MWCNT aerosols in workplaces. The measurement scheme should be relevant for any carbon nanotube aerosol. PMID:23033994

Population Size and Distribution of Rhizobium leguminosarum bv. trifolii in Relation to Total Soil Bacteria and Soil Depth †

PubMed Central

Bottomley, Peter J.; Dughri, Muktar H.

1989-01-01

Bacterial cells small enough to pass through 0.4-μm-pore-size filters made up 5 to 9% of the indigenous bacterial population in 0- to 20-cm-depth samples of Abiqua silty clay loam. Within the same soil samples, cells of a similar dimension were stained with fluorescent antibodies specific to each of four antigenically distinct indigenous serogroups of Rhizobium leguminosarum bv. trifolii and made up 22 to 34% of the soil population of the four serogroups. Despite the extensive contribution of small cells to these soil populations, no evidence of their being capable of either growth or nodulation was obtained. The density of soil bacteria which could be cultured ranged between 0.5 and 8.5% of the >0.4-μm direct count regardless of media, season of sampling, or soil depth. In the same soil samples, the viable nodulating populations of biovar trifolii determined by the plant infection soil dilution technique ranged between 1 and 10% of the >0.4-μm direct-immunofluorescence count of biovar trifolii. The <0.4-μm cell populations of both total soil bacteria and biovar trifolii changed abruptly between the 10- to 15-cm and 15- to 20-cm soil depth increments, increasing from 5 to 20% and from 20 to 50%, respectively, of their direct-count totals. The increase in density of the small-cell population corresponded to a significant increase in soil bulk density (1.07 to 1.21 g cm−3). The percent contribution of the <0.4-μm direct count to individual serogroup totals increased with soil depth by approximately 2-fold (39 to 87%) for serogroups 17 and 21 and by 12-fold (6 to 75%) for serogroups 6 and 36. PMID:16347896

Are adult patients with Laron syndrome osteopenic? A comparison between dual-energy X-ray absorptiometry and volumetric bone densities.

PubMed

Benbassat, Carlos A; Eshed, Varda; Kamjin, Moshe; Laron, Zvi

2003-10-01

Severe short stature resulting from a deficiency in IGF-I is a prominent feature of Laron syndrome (LS). Although low bone mineral density (BMD) has been noted in LS patients examined by dual energy x-ray absorptiometry (DEXA), this technique does not take volume into account and may therefore underestimate the true bone density in patients with small bones. The aim of the present study was to evaluate the BMD yielded by DEXA in our LS patients using estimated volumetric values. Volumetric density was calculated with the following formulas: bone mineral apparent density (BMAD) = bone mineral content (BMC)/(area)(3/2) for the lumbar spine and BMAD = BMC/area(2) for the femoral neck. The study sample included 12 patients (mean age, 43.9 yr; mean height, 123.7 cm). Findings were compared with 10 osteopenic subjects without developmental abnormalities (mean age, 56 yr; mean height, 164.8 cm) and 10 healthy control subjects matched for sex and age to the LS patients (mean height, 165.5 cm). BMAD in the LS group was 0.201 +/- 0.02 g/cm(3) at the lumbar spine and 0.201 +/- 0.04 g/cm(3) at the femoral neck; corresponding values for the osteopenic group were 0.130 +/- 0.01 and 0.140 +/- 0.01 g/cm(3), and for the controls, 0.178 +/- 0.03 and 0.192 +/- 0.02 g/cm(3). Although areal BMD was significantly lower in the LS and osteopenic subjects compared with controls (P < 0.02) at both the lumbar spine and femoral neck, BMAD was low (P < 0.01) in the osteopenic group only. In conclusion, DEXA does not seem to be a reliable measure of osteoporosis in patients with LS.

Total organic carbon in a soil recovered with sewage sludge and native species of the Atlantic Forest

NASA Astrophysics Data System (ADS)

Mara Lima Goulart, Lívia; Amaral Guerrini, Iraê; Fidalgo de Faria, Marianne; Spada, Grasiela; Proença Nalesso, Pedro Henrique; Willian Carlos, Guilherme

2017-04-01

The use of organic waste such as sewage sludge, in the recovery of degraded áreas have shown very satisfactory results, because they are constituted by high contentes of organic matter and nutrients, essential to improve the physical and chemical properties of the soil. Thus, the objective of this study was to verify the total organic carbon (TOC) of a degraded soil, up to a metre deep, after 10 years of application of sewage sludge and planting native species of the Atlantic forest. The experiment was conducted at Fazenda Entre-Rios, owned by Suzano Papel e Celulose, in Itatinga, São Paulo, Brazil. The experiment was designed as randomized block with four replications, six doses of sewage sludge (0, 2.5, 5, 10, 15 and 20 t ha-1), conventional chemical fertilizer and only with potassium application, totaling eight treatments. Samples were collected every 20 cm (0-20, 20-40, 40-60, 60-80 and 80-100 cm) until reaching a metre deep. Ten years after trial deployment, the sewage sludge application in degraded soil was significantly influenced the TOC at all depths sampled. The highest values of the COT were observed in plots that received 15 and 20 t ha-1 of sewage sludge, in all depths sampled, except for the layer of 80-100 cm, which presented the highest average COT in the treatment with 10 t ha-1 of residue. As observed for all treatments, the highest TOC averages were observed in the superficial layers of the soil (0-20 and 20-40 cm). The sewage sludge application is useful to recover degraded soils, as it improving their chemical characteristics and showing to be a good alternative to the final destination of this residue.

40 CFR 90.414 - Raw gaseous exhaust sampling and analytical system description.

Code of Federal Regulations, 2013 CFR

2013-07-01

... savers” or “protectors” with nonreactive diaphragms to reduce dead volumes is permitted. (b) Sample probe. (1) The sample probe must be a straight, closed end, stainless steel, multi-hole probe. The inside... probe may not be greater than 0.10 cm. The fitting that attaches the probe to the exhaust pipe must be...

40 CFR 90.414 - Raw gaseous exhaust sampling and analytical system description.

Code of Federal Regulations, 2012 CFR

2012-07-01

... savers” or “protectors” with nonreactive diaphragms to reduce dead volumes is permitted. (b) Sample probe. (1) The sample probe must be a straight, closed end, stainless steel, multi-hole probe. The inside... probe may not be greater than 0.10 cm. The fitting that attaches the probe to the exhaust pipe must be...

40 CFR 90.414 - Raw gaseous exhaust sampling and analytical system description.

Code of Federal Regulations, 2014 CFR

2014-07-01

... savers” or “protectors” with nonreactive diaphragms to reduce dead volumes is permitted. (b) Sample probe. (1) The sample probe must be a straight, closed end, stainless steel, multi-hole probe. The inside... probe may not be greater than 0.10 cm. The fitting that attaches the probe to the exhaust pipe must be...

Influence of 400 keV carbon ion implantation on structural, optical and electrical properties of PMMA

NASA Astrophysics Data System (ADS)

Arif, Shafaq; Rafique, M. Shahid; Saleemi, Farhat; Sagheer, Riffat; Naab, Fabian; Toader, Ovidiu; Mahmood, Arshad; Rashid, Rashad; Mahmood, Mazhar

2015-09-01

Ion implantation is a useful technique to modify surface properties of polymers without altering their bulk properties. The objective of this work is to explore the 400 keV C+ ion implantation effects on PMMA at different fluences ranging from 5 × 1013 to 5 × 1015 ions/cm2. The surface topographical examination of irradiated samples has been performed using Atomic Force Microscope (AFM). The structural and chemical modifications in implanted PMMA are examined by Raman and Fourier Infrared Spectroscopy (FTIR) respectively. The effects of carbon ion implantation on optical properties of PMMA are investigated by UV-Visible spectroscopy. The modifications in electrical conductivity have been measured using a four point probe technique. AFM images reveal a decrease in surface roughness of PMMA with an increase in ion fluence from 5 × 1014 to 5 × 1015 ions/cm2. The existence of amorphization and sp2-carbon clusterization has been confirmed by Raman and FTIR spectroscopic analysis. The UV-Visible data shows a prominent red shift in absorption edge as a function of ion fluence. This shift displays a continuous reduction in optical band gap (from 3.13 to 0.66 eV) due to formation of carbon clusters. Moreover, size of carbon clusters and photoconductivity are found to increase with increasing ion fluence. The ion-induced carbonaceous clusters are believed to be responsible for an increase in electrical conductivity of PMMA from (2.14 ± 0.06) × 10-10 (Ω-cm)-1 (pristine) to (0.32 ± 0.01) × 10-5 (Ω-cm)-1 (irradiated sample).

Development of a case-mix funding system for adults with combined vision and hearing loss.

PubMed

Guthrie, Dawn M; Poss, Jeffrey W

2013-04-15

Adults with vision and hearing loss, or dual sensory loss (DSL), present with a wide range of needs and abilities. This creates many challenges when attempting to set the most appropriate and equitable funding levels. Case-mix (CM) funding models represent one method for understanding client characteristics that correlate with resource intensity. A CM model was developed based on a derivation sample (n = 182) and tested with a replication sample (n = 135) of adults aged 18+ with known DSL who were living in the community. All items within the CM model came from a standardized, multidimensional assessment, the interRAI Community Health Assessment and the Deafblind Supplement. The main outcome was a summary of formal and informal service costs which included intervenor and interpreter support, in-home nursing, personal support and rehabilitation services. Informal costs were estimated based on a wage rate of half that for a professional service provider ($10/hour). Decision-tree analysis was used to create groups with homogeneous resource utilization. The resulting CM model had 9 terminal nodes. The CM index (CMI) showed a 35-fold range for total costs. In both the derivation and replication sample, 4 groups (out of a total of 18 or 22.2%) had a coefficient of variation value that exceeded the overall level of variation. Explained variance in the derivation sample was 67.7% for total costs versus 28.2% in the replication sample. A strong correlation was observed between the CMI values in the two samples (r = 0.82; p = 0.006). The derived CM funding model for adults with DSL differentiates resource intensity across 9 main groups and in both datasets there is evidence that these CM groups appropriately identify clients based on need for formal and informal support.

Poster — Thur Eve — 21: Off-axis dose perturbation effects in water in a 5 × 5 cm{sup 2} 18 MV photon beam for the PTW microLion and Exradin A1SL ionization chambers

DOE Office of Scientific and Technical Information (OSTI.GOV)

O'Grady, K; Davis, S D; Papaconstadopoulos, P

2014-08-15

A PTW microLion liquid ionization chamber and an Exradin A1SL air-filled ionization chamber have been modeled using the egs-chamber user code of the EGSnrc system to determine their perturbation effects in water in a 5 × 5 cm{sup 2} 18 MV photon beam. A model of the Varian CL21EX linear accelerator was constructed using the BEAMnrc Monte Carlo code, and was validated by comparing measured PDDs and profiles from the microLion and A1SL chambers to calculated results that included chamber models. Measured PDDs for a 5 × 5 cm{sup 2} field for the microLion chamber agreed with calculations to withinmore » 1.5% beyond a depth of 0.5 cm, and the A1SL PDDs agreed within 1.0% beyond 1.0 cm. Measured and calculated profiles at 10 cm depth agreed within 1.0% for both chambers inside the field, and within 4.0% near the field edge. Local percent differences increased up to 15% at 4 cm outside the field. The ratio of dose to water in the absence of the chamber relative to dose in the chamber's active volume as a function of off-axis distance was calculated using the egs-chamber correlated sampling technique. The dose ratio was nearly constant inside the field and consistent with the stopping power ratios of water to detector material, but varied up to 3.3% near the field edge and 5.2% at 4 cm outside the field. Once these perturbation effects are fully characterized for more field sizes and detectors, they could be applied to clinical water tank measurements for improved dosimetric accuracy.« less

Impacts of soil moisture content on visual soil evaluation

NASA Astrophysics Data System (ADS)

Emmet-Booth, Jeremy; Forristal, Dermot; Fenton, Owen; Bondi, Giulia; Creamer, Rachel; Holden, Nick

2017-04-01

Visual Soil Examination and Evaluation (VSE) techniques offer tools for soil quality assessment. They involve the visual and tactile assessment of soil properties such as aggregate size and shape, porosity, redox morphology, soil colour and smell. An increasing body of research has demonstrated the reliability and utility of VSE techniques. However a number of limitations have been identified, including the potential impact of soil moisture variation during sampling. As part of a national survey of grassland soil quality in Ireland, an evaluation of the impact of soil moisture on two widely used VSE techniques was conducted. The techniques were Visual Evaluation of Soil Structure (VESS) (Guimarães et al., 2011) and Visual Soil Assessment (VSA) (Shepherd, 2009). Both generate summarising numeric scores that indicate soil structural quality, though employ different scoring mechanisms. The former requires the assessment of properties concurrently and the latter separately. Both methods were deployed on 20 sites across Ireland representing a range of soils. Additional samples were taken for soil volumetric water (θ) determination at 5-10 and 10-20 cm depth. No significant correlation was observed between θ 5-10 cm and either VSE technique. However, VESS scores were significantly related to θ 10-20 cm (rs = 0.40, sig = 0.02) while VSA scores were not (rs = -0.33, sig = 0.06). VESS and VSA scores can be grouped into quality classifications (good, moderate and poor). No significant mean difference was observed between θ 5-10 cm or θ 10-20 cm according to quality classification by either method. It was concluded that VESS scores may be affected by soil moisture variation while VSA appear unaffected. The different scoring mechanisms, where the separate assessment and scoring of individual properties employed by VSA, may limit soil moisture effects. However, moisture content appears not to affect overall structural quality classification by either method. References Guimarães, R.M.C., Ball, B.C. & Tormena, C.A. 2011. Improvements in the visual evaluation of soil structure, Soil Use and Management, 27, 3: 395-403 Shepherd, G.T. 2009. Visual Soil Assessment. Field guide for pastoral grazing and cropping on flat to rolling country. 2nd edn. Horizons regional council, New Zealand.

Evaluation of latent variances in Monte Carlo dose calculations with Varian TrueBeam photon phase-spaces used as a particle source

NASA Astrophysics Data System (ADS)

Alhakeem, Eyad; Zavgorodni, Sergei

2018-01-01

The purpose of this study was to evaluate the latent variance (LV) of Varian TrueBeam photon phase-space files (PSF) for open 10  ×  10 cm2 and small stereotactic fields and estimate the number of phase spaces required to be summed up in order to maintain sub-percent LV in Monte Carlo (MC) dose calculations. BEAMnrc/DOSXYZnrc software was used to transport particles from Varian phase-space files (PSFA) through the secondary collimators. Transported particles were scored into another phase-space located under the jaws (PSFB), or transported further through the cone collimators and scored straight below, forming PSFC. Phase-space files (PSFB) were scored for 6 MV-FFF, 6 MV, 10 MV-FFF, 10 MV and 15 MV beams with 10  ×  10 cm2 field size, and PSFC were scored for 6 MV beam under circular cones of 0.13, 0.25, 0.35, and 1 cm diameter. Both PSFB and PSFC were transported into a water phantom with particle recycling number ranging from 10 to 1000. For 10  ×  10 cm2 fields 0.5  ×  0.5  ×  0.5 cm3 voxels were used to score the dose, whereas the dose was scored in 0.1  ×  0.1  ×  0.5 cm3 voxels for beams collimated with small cones. In addition, for small 0.25 cm diameter cone-collimated 6 MV beam, phantom voxel size varied as 0.02  ×  0.02  ×  0.5 cm3, 0.05  ×  0.05  ×  0.5 cm3 and 0.1  ×  0.1  ×  0.5 cm3. Dose variances were scored in all cases and LV evaluated as per Sempau et al. For the 10  ×  10 cm2 fields calculated LVs were greatest at the phantom surface and decreased with depth until they reached a plateau at 5 cm depth. LVs were found to be 0.54%, 0.96%, 0.35%, 0.69% and 0.57% for the 6 MV-FFF, 6 MV, 10 MV-FFF, 10 MV and 15 MV energies, respectively at the depth of 10 cm. For the 6 MV phase-space collimated with cones of 0.13, 0.25, 0.35, 1.0 cm diameter, the LVs calculated at 1.5 cm depth were 75.6%, 25.4%, 17.6% and 8.0% respectively. Calculated LV for the 0.25 cm cone-collimated 6 MV beam were 61.2%, 40.7%, 22.5% in 0.02  ×  0.02  ×  0.5 cm3, 0.05  ×  0.05  ×  0.5 cm3 and 0.1  ×  0.1  ×  0.5 cm3 voxels respectively. In order to achieve sub-percent LV in open 10  ×  10 cm2 field MC simulations a single PSF can be used, whereas for small SRS fields (0.13-1.0 cm) more PSFs (66-8 PSFs) would have to be summed.

Thermoelectric Properties of Sr-Filled Ge-Based Type I Single-Crystal Clathrate Grown by Sn-Flux Method

NASA Astrophysics Data System (ADS)

Deng, Shuping; Liu, Hongxia; Li, Decong; Wang, Jinsong; Cheng, Feng; Shen, Lanxian; Deng, Shukang

2017-05-01

Single-crystal samples of Sr-filled Ge-based type I clathrate have been prepared by the Sn-flux method, and their thermoelectric properties investigated. The obtained samples exhibited n-type conduction with carrier concentration varying from 2.8 × 1019/cm3 to 6.8 × 1019/cm3 as the carrier mobility changed from 23.9 cm2/V-s to 15.1 cm2/V-s at room temperature. Structural analysis indicated that all samples were type I clathrate in space group pm\\bar{it{3}}n . The total content of group IV (Ge + Sn) atoms in the crystalline structure increased with increasing x value (where x defines the atomic ratio of starting elements, Sr:Ga:Ge:Sn = 8:16: x:20), reaching a maximum value of 31.76 at.% for the sample with x = 30; consequently, the lattice parameters increased. The melting points for all samples were approximately 1012 K, being considerably lower than that of single-crystal Sr8Ga16Ge30 prepared by other methods. The electrical conductivity increased while the absolute value of α increased gradually with increasing temperature; the maximum value of α reached 193 μV/K at 750 K for the sample with x = 24. The sample with x = 30 exhibited lower lattice thermal conductivity of 0.80 W/m-K. As a result, among all the Sn-flux samples, single-crystal Sr7.92Ga15.04Sn0.35Ge30.69 had the largest ZT value of 1.0 at about 750 K.

Heavy ion irradiations on synthetic hollandite-type materials: Ba{sub 1.0}Cs{sub 0.3}A{sub 2.3}Ti{sub 5.7}O{sub 16} (A=Cr, Fe, Al)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tang, Ming, E-mail: mtang@lanl.gov; Tumurugoti, Priyatham; Clark, Braeden

2016-07-15

The hollandite supergroup of minerals has received considerable attention as a nuclear waste form for immobilization of Cs. The radiation stability of synthetic hollandite-type compounds described generally as Ba{sub 1.0}Cs{sub 0.3}A{sub 2.3}Ti{sub 5.7}O{sub 16} (A=Cr, Fe, Al) were evaluated by heavy ion (Kr) irradiations on polycrystalline single phase materials and multiphase materials incorporating the hollandite phases. Ion irradiation damage effects on these samples were examined using grazing incidence X-ray diffraction (GIXRD) and transmission electron microscopy (TEM). Single phase compounds possess tetragonal structure with space group I4/m. GIXRD and TEM observations revealed that 600 keV Kr irradiation-induced amorphization on single phasemore » hollandites compounds occurred at a fluence between 2.5×10{sup 14} Kr/cm{sup 2} and 5×10{sup 14} Kr/cm{sup 2}. The critical amorphization fluence of single phase hollandite compounds obtained by in situ 1 MeV Kr ion irradiation was around 3.25×10{sup 14} Kr/cm{sup 2}. The hollandite phase exhibited similar amorphization susceptibility under Kr ion irradiation when incorporated into a multiphase system. - Graphical abstract: 600 keV Kr irradiation-induced amorphization on single phase hollandites compounds occurred at a fluence between 2.5×10{sup 14} Kr/cm{sup 2} and 5×10{sup 14} Kr/cm{sup 2}. The hollandite phase exhibited similar amorphization susceptibility under Kr ion irradiation when incorporated into a multiphase system. This is also the first time that the critical amorphization fluence of single phase hollandite compounds were determined at a fluence of around 3.25×10{sup 14} Kr/cm{sup 2} by in situ 1 MeV Kr ion irradiation. Display Omitted.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tsuo, Y.S.; Deng, X.J.; Smith, E.B.

We have studied the rehydrogenation and post-hydrogenation of a-Si:H using a Kaufman ion beam source. The achievement of an air-mass-one (AM1), photo-to-dark conductivity ratio of 5.6 x 10/sup 5/ with a rehydrogenated a-Si:H sample was reported earlier (Y. S. Tsuo, E. B. Smith, and S. K. Deb, Appl. Phys. Lett. 51, 1436 (1987)). In this communication we report recent results of the rehydrogenation study and new results of a study of the post-hydrogenation of amorphous silicon deposited by glow discharge at 480 /sup 0/C. AM1 photo-to-dark conductivity ratios as high as 9.5 x 10/sup 6/ (with a photoconductivity of 8.6more » x 10/sup -6/ ..cap omega.. cm/sup -1/) and 1.1 x 10/sup 5/ (with a photoconductivity of 6.3 x 10/sup -6/ ..cap omega.. cm/sup -1/) have been obtained with a rehydrogenated sample and a post-hydrogenated sample, respectively. We also report the results of the hydrogen depth profile and photostability measurements of these samples.« less

Physical and chemical characteristics including total and geochemical forms of phosphorus in sediment from the top 30 centimeters of cores collected in October 2006 at 26 sites in Upper Klamath Lake, Oregon

USGS Publications Warehouse

Simon, Nancy S.; Ingle, Sarah N.

2011-01-01

μThis study of phosphorus (P) cycling in eutrophic Upper Klamath Lake (UKL), Oregon, was conducted by the U.S. Geological Survey in cooperation with the U.S. Bureau of Reclamation. Lakebed sediments from the upper 30 centimeters (cm) of cores collected from 26 sites were characterized. Cores were sampled at 0.5, 1.5, 2.5, 3.5, 4.5, 10, 15, 20, 25, and 30 cm. Prior to freezing, water content and sediment pH were determined. After being freeze-dried, all samples were separated into greater than 63-micron (μm) particle-size (coarse) and less than 63-μm particle-size (fine) fractions. In the surface samples (0.5 to 4.5 cm below the sediment water interface), approximately three-fourths of the particles were larger than 63-μm. The ratios of the coarse particle-size fraction (>63 μm) and the fine particle-size fraction (<63 μm) were approximately equal in samples at depths greater than 10 cm below the sediment water interface. Chemical analyses included both size fractions of freeze-dried samples. Chemical analyses included determination of total concentrations of aluminum (Al), calcium (Ca), carbon (C), iron (Fe), poorly crystalline Fe, nitrogen (N), P, and titanium (Ti). Total Fe concentrations were the largest in sediment from the northern portion of UKL, Howard Bay, and the southern portion of the lake. Concentrations of total Al, Ca, and Ti were largest in sediment from the northern, central, and southernmost portions of the lake and in sediment from Howard Bay. Concentrations of total C and N were largest in sediment from the embayments and in sediment from the northern arm and southern portion of the lake in the general region of Buck Island. Concentrations of total C were larger in the greater than 63-μm particle-size fraction than in the less than 63-μm particle-size fraction. Sediments were sequentially extracted to determine concentrations of inorganic forms of P, including loosely sorbed P, P associated with poorly crystalline Fe oxides, and P associated with mineral phases. The difference between the concentration of total P and sum of the concentrations of inorganic forms of P is referred to as residual P. Residual P was the largest fraction of P in all of the sediment samples. In UKL, the correlation between concentrations of total P and total Fe in sediment is poor (R2<0.1). The correlation between the concentrations of total P and P associated with poorly crystalline Fe oxides is good (R2=0.43) in surface sediment (0.5-4.5 cm below the sediment water interface) but poor (R2<0.1) in sediments at depths between 10 cm and 30 cm. Phosphorus associated with poorly crystalline Fe oxides is considered bioavailable because it is released when sediment conditions change from oxidizing to reducing, which causes dissolution of Fe oxides.

Air contamination for predicting wound contamination in clean surgery: A large multicenter study.

PubMed

Birgand, Gabriel; Toupet, Gaëlle; Rukly, Stephane; Antoniotti, Gilles; Deschamps, Marie-Noelle; Lepelletier, Didier; Pornet, Carole; Stern, Jean Baptiste; Vandamme, Yves-Marie; van der Mee-Marquet, Nathalie; Timsit, Jean-François; Lucet, Jean-Christophe

2015-05-01

The best method to quantify air contamination in the operating room (OR) is debated, and studies in the field are controversial. We assessed the correlation between 2 types of air sampling and wound contaminations before closing and the factors affecting air contamination. This multicenter observational study included 13 ORs of cardiac and orthopedic surgery in 10 health care facilities. For each surgical procedure, 3 microbiologic air counts, 3 particles counts of 0.3, 0.5, and 5 μm particles, and 1 bacteriologic sample of the wound before skin closure were performed. We collected data on surgical procedures and environmental characteristics. Of 180 particle counts during 60 procedures, the median log10 of 0.3, 0.5, and 5 μm particles was 7 (interquartile range [IQR], 6.2-7.9), 6.1 (IQR, 5.4-7), and 4.6 (IQR, 0-5.2), respectively. Of 180 air samples, 50 (28%) were sterile, 90 (50%) had 1-10 colony forming units (CFU)/m(3) and 40 (22%) >10 CFU/m(3). In orthopedic and cardiac surgery, wound cultures at closure were sterile for 24 and 9 patients, 10 and 11 had 1-10 CFU/100 cm(2), and 0 and 6 had >10 CFU/100 cm(2), respectively (P < .01). Particle sizes and a turbulent ventilation system were associated with an increased number of air microbial counts (P < .001), but they were not associated with wound contamination (P = .22). This study suggests that particle counting is a good surrogate of airborne microbiologic contamination in the OR. Copyright © 2015 Association for Professionals in Infection Control and Epidemiology, Inc. Published by Elsevier Inc. All rights reserved.

The Rovibrational Intensities of Five Absorption Bands of (12)C(16)O2 Between 5218 and 5349/cm

NASA Technical Reports Server (NTRS)

Giver, Lawrence P.; Brown, Linda R.; Chackerian, Charles, Jr.; Freedman, Richard S.; Gore, Warren J. (Technical Monitor)

2002-01-01

Absolute line intensities, band intensities, and Herman-Wallis parameters were measured for the (01(sup 1)2)(sub I) from (00(sup 0)0)(sub I) perpendicular band of (12)C(16)O2 centered at 5315/cm, along with the three nearby associated hot bands: (10(sup 0)2)(sub II) from (01(sup 1)0)(sub I) at 5248/cm, (02(sup 2))(sub I) from (01(sup 1)0)(sub I) at 5291/cm, and (10(sup 0)2)(sub I) from (01(sup 1)0)(sub I) at 5349/cm. The nearby parallel hot band (30(sup 0))(sub I) from (10(sup 0)0)(sub II) at 5218/cm was also included in this study.

Tritium retention in S-65 beryllium after 100 eV plasma exposure

NASA Astrophysics Data System (ADS)

Causey, Rion A.; Longhurst, Glen R.; Harbin, Wally

1997-02-01

The tritium plasma experiment (TPE) has been used to measure the retention of tritium in S-65 beryllium under conditions similar to that expected for the international thermonuclear experimental reactor (ITER). Beryllium samples 2 mm thick and 50 mm in diameter were exposed to a plasma of tritium and deuterium. The particle flux striking the samples was varied from approximately 1 × 10 17 ( D + T)/ cm2s up to about 3 × 10 18 ( D + T)/ cm2s. The beryllium samples were negatively biased to elevate the energy of the impinging ions to 100 eV. The temperature of the samples was varied from 373 K to 973 K. Exposure times of 1 h were used. Subsequent to the plasma exposure, the samples were outgassed in a separate system where 99% He and 1% H 2 gas was swept over the samples during heating. The sweep gas along with the released tritium was sent through an ionization chamber, through a copper oxide catalyst bed, and into a series of glycol bubblers. The amount of released tritium was determined both by the ionization chamber and by liquid scintillation counting of the glycol. Tritium retention in the beryllium disks varied from a high of 2.4 × 10 17 ( D + T)/ cm2 at 373 K to a low of 1 × 10 16 ( D + T)/ cm2 at 573 K. For almost every case, the tritium retention in the beryllium was less than that calculated using the C = 0 boundary condition at the plasma facing surface. It is believed that this lower than expected retention is due to rapid release of tritium from the large specific surface area created in the implant zone due to the production of voids, bubbles, and blisters.

The correlation between concentrations of zolpidem and benzodiazepines in segmental hair samples and use patterns.

PubMed

Kim, Hyojeong; Lee, Sangeun; In, Sanghwan; Park, Meejung; Cho, Sungnam; Shin, Junguk; Lee, Hunjoo; Han, Eunyoung

2018-01-01

The aim of this study was to investigate the correlation between histories of zolpidem and benzodiazepines use and their concentrations in hair as determined by segmental hair analysis, that is, by analyzing hair samples taken 0-1, 1-2, 2-3, 3-4, 4-5, and 5-6cm etc. and 0-3cm from the scalp, and whole hair. Of the 23 hair samples examined, 18 were collected from patients in a rehabilitation program and five were from patients that had taken zolpidem only once by prescription. All 23 patients provided written informed consent after reviewing the research plan, described their zolpidem and benzodiazepines use histories accurately, and provided hair samples, which were weighed, washed, cut into lengths of <1mm, and extracted in 100% methanol for 16h (diazepam-d 5 was used as an internal standard). Extracts were evaporated under reduced pressure and reconstituted with aqueous methanol (1:1 v/v). These extracts (10μL) were analyzed by Liquid Chromatography/Tandem Mass Spectrometry (LC-MS/MS). The method used was validated by determining LOD, LOQ, calibration curves, intra- and inter-accuracies, precisions, matrix effects, process efficiencies, extraction efficiencies, and processed sample stabilities. Five hundred and ninety-five 1cm hair segments showed 61.59% positive probability and 86.71% negative probability of quality correlation between zolpidem and benzodiazepines use and concentrations in hair. Good qualitative correlations were observed between drug use and detection in hair. False positivity and false negativity were very low. Of the hair samples taken from patients in a rehabilitation program, subject nos. 4, 5, and 12 had correlation coefficients of 0.68, 0.54 and 0.71, respectively, for relationships between zolpidem use and concentration of zolpidem in hair. For the 5 patients taking only a single dose of zolpidem (10mg), the average zolpidem concentrations in hair were 20, 15 and 40pg/mg after 5, 30 and 60 days, respectively. This study shows a relationship between history of zolpidem and benzodiazepines use and their concentrations in 1cm hair segment. Copyright © 2017 Elsevier B.V. All rights reserved.

The Effects of Bit Wear on Respirable Silica Dust, Noise and Productivity: A Hammer Drill Bench Study.

PubMed

Carty, Paul; Cooper, Michael R; Barr, Alan; Neitzel, Richard L; Balmes, John; Rempel, David

2017-07-01

Hammer drills are used extensively in commercial construction for drilling into concrete for tasks including rebar installation for structural upgrades and anchor bolt installation. This drilling task can expose workers to respirable silica dust and noise. The aim of this pilot study was to evaluate the effects of bit wear on respirable silica dust, noise, and drilling productivity. Test bits were worn to three states by drilling consecutive holes to different cumulative drilling depths: 0, 780, and 1560 cm. Each state of bit wear was evaluated by three trials (nine trials total). For each trial, an automated laboratory test bench system drilled 41 holes 1.3 cm diameter, and 10 cm deep into concrete block at a rate of one hole per minute using a commercially available hammer drill and masonry bits. During each trial, dust was continuously captured by two respirable and one inhalable sampling trains and noise was sampled with a noise dosimeter. The room was thoroughly cleaned between trials. When comparing results for the sharp (0 cm) versus dull bit (1560 cm), the mean respirable silica increased from 0.41 to 0.74 mg m-3 in sampler 1 (P = 0.012) and from 0.41 to 0.89 mg m-3 in sampler 2 (P = 0.024); levels above the NIOSH recommended exposure limit of 0.05 mg m-3. Likewise, mean noise levels increased from 112.8 to 114.4 dBA (P < 0.00001). Drilling productivity declined with increasing wear from 10.16 to 7.76 mm s-1 (P < 0.00001). Increasing bit wear was associated with increasing respirable silica dust and noise and reduced drilling productivity. The levels of dust and noise produced by these experimental conditions would require dust capture, hearing protection, and possibly respiratory protection. The findings support the adoption of a bit replacement program by construction contractors. © The Author 2017. Published by Oxford University Press on behalf of the British Occupational Hygiene Society.

Electrical characterization of deep levels created by bombarding nitrogen-doped 4H-SiC with alpha-particle irradiation

NASA Astrophysics Data System (ADS)

Omotoso, Ezekiel; Meyer, Walter E.; Auret, F. Danie; Paradzah, Alexander T.; Legodi, Matshisa J.

2016-03-01

Deep-level transient spectroscopy (DLTS) and Laplace-DLTS were used to investigate the effect of alpha-particle irradiation on the electrical properties of nitrogen-doped 4H-SiC. The samples were bombarded with alpha-particles at room temperature (300 K) using an americium-241 (241Am) radionuclide source. DLTS revealed the presence of four deep levels in the as-grown samples, E0.09, E0.11, E0.16 and E0.65. After irradiation with a fluence of 4.1 × 1010 alpha-particles-cm-2, DLTS measurements indicated the presence of two new deep levels, E0.39 and E0.62 with energy levels, EC - 0.39 eV and EC - 0.62 eV, with an apparent capture cross sections of 2 × 10-16 and 2 × 10-14 cm2, respectively. Furthermore, irradiation with fluence of 8.9 × 1010 alpha-particles-cm-2 resulted in the disappearance of shallow defects due to a lowering of the Fermi level. These defects re-appeared after annealing at 300 °C for 20 min. Defects, E0.39 and E0.42 with close emission rates were attributed to silicon or carbon vacancy and could only be separated by using high resolution Laplace-DLTS. The DLTS peaks at EC - (0.55-0.70) eV (known as Z1/Z2) were attributed to an isolated carbon vacancy (VC).

Physical properties of a non-transparent cadmium oxide thick film deposited at low fluence by pulsed laser deposition

DOE Office of Scientific and Technical Information (OSTI.GOV)

Quiñones-Galván, J.G., E-mail: erk_183@hotmail.com; Lozada-Morales, R.; Jiménez-Sandoval, S.

Highlights: • A non-transparent cadmium oxide film has been deposited by pulsed laser deposition. • The CdO film is polycrystalline and highly oriented in the (2 0 0) direction. • Thermal treatment was applied in order to see the effect on its physical properties. - Abstract: A stable non-transparent CdO film was grown by pulsed laser deposition. The sample was thermally annealed at 500 °C in air. A (2 0 0) highly oriented polycrystalline film was obtained. The annealed sample has not preferred orientation. Scanning electron micrographs show a grain size reduction for the annealed sample. By Raman spectroscopy, themore » defects related second order vibrational modes of CdO were observed. Chemical composition analysis shows the presence of CdO together with a substoichiometric CdO{sub x} phase for the as-grown sample. For the annealed sample a compensation of oxygen vacancies was observed. Electrical resistivity measurements give a value of 8.602 × 10{sup −4} (Ω cm) for the as-grown film. For the annealed sample the electrical resistivity increased to a value of 9.996 × 10{sup −3} (Ω cm). Zero transmission has never been reported for CdO films. The photoluminescence spectra were measured in order to shed some light on the origin of the zero transmission.« less

[Study on predicting sugar content and valid acidity of apples by near infrared diffuse reflectance technique].

PubMed

Liu, Yan-de; Ying, Yi-bin; Fu, Xia-ping

2005-11-01

The nondestructive method for quantifying sugar content (SC) and available acid (VA) of intact apples using diffuse near infrared reflectance and optical fiber sensing techniques were explored in the present research. The standard sample sets and prediction models were established by partial least squares analysis (PLS). A total of 120 Shandong Fuji apples were tested in the wave number of 12,500 - 4000 cm(-1) using Fourier transform near infrared spectroscopy. The results of the research indicated that the nondestructive quantification of SC and VA, gave a high correlation coefficient 0.970 and 0.906, a low root mean square error of prediction (RMSEP) 0.272 and 0.056 2, a low root mean square error of calibration (RMSEC) 0.261 and 0.0677, and a small difference between RMSEP and RMSEC 0.011 a nd 0.0115. It was suggested that the diffuse nearinfrared reflectance technique be feasible for nondestructive determination of apple sugar content in the wave number range of 10,341 - 5461 cm(-1) and for available acid in the wave number range of 10,341 - 3818 cm(-1).

An evaluation of selected methods for the decontamination of cattle hides prior to skinning.

PubMed

Small, A; Wells-Burr, B; Buncic, S

2005-02-01

The effectiveness of different decontamination treatments in reducing microbial loads on cattle hides was assessed. The 10-s hide treatments were conducted using a wet-and-dry vacuum cleaner filled with one of the liquids (heated to 50 °C) indicated below, followed or not by 10-min drying in the air. Also, the hide was clipped, followed or not by 10-s singeing using a hand-held blowtorch. Before and after each decontamination treatment, the hide was sampled (100 cm(2) areas) by a sponge-swabbing method to compare the total viable counts of bacteria (TVC). The largest bacterial reduction (P<0.001; 2.31log(10) cfu/cm(2)) was achieved by singeing of previously clipped hide. Treatment of hide with a food industry sanitizer solution (10% Betane Plus) resulted in significant reductions of 1.80 (P<0.001) and 1.98log(10) cfu/cm(2) (P<0.001) without and with subsequent drying, respectively. Treatment of hide with a food industry disinfectant (P3-Topactive DES) significantly reduced TVC by 0.97 (P<0.001) and 1.18log(10) cfu/cm(2) (P<0.001) without and with subsequent drying, respectively. Treatments of hide with water alone or with a food-safe detergent solution (Formula 963B), or hide clipping alone, did not produce significant decontamination effects. Since hide contamination is associated with microbial contamination of the carcasses, the results indicate that post-killing/pre-skinning hide decontamination (used alone, or in combination with carcass decontamination) has a potential to improve microbial meat safety. Nevertheless, further research is required to optimise the efficacy of these treatments in the reduction of specific pathogens under commercial conditions.

Nanoelectrospray with ion-trap mass spectrometry for the determination of beta-casomorphins in derived milk products.

PubMed

Juan-García, Ana; Font, Guillermina; Juan, Cristina; Picó, Yolanda

2009-11-15

Beta-casomorphins (b-CMs) are bioactive peptides derived from casein with opioid agonist effects similar to morphine. The use of electrospray (ESI) with quadrupole ion-trap mass spectrometry (QIT-MS) for these compounds in two matrices, cheese and milk, was examined. It was compared to a liquid chromatography (LC) coupled to mass spectrometry (LC-MS), and a "soft" ionisation technique, NanoMate, with selected ion monitoring (SIM), which are unreliable for the determination of trace casomorphins in derived milk products. b-CM mass fragmentation pathways were done for the four most common b-CMs: beta-casomorphin (1-5) bovine (b-CM-5), beta-casomorphin (1-7) bovine (b-CM-7), [D-Ala2, D-Pro4,Tyr5]-beta-casomorphin (1-5) amide (b-CM-10) and beta-casomorphin (1-5) amide [D-Ala2,Hyp4,Tyr5] (b-CM-11). The major product ions obtained in QIT-MS were used to construct fragmentation pathways for b-CMs. The different collision energies using automated nanoelectrospray ion source NanoMate and conventional LC in QIT-MS were studied. Calibration data for b-CMs, using spiked milk or cheese samples (10 g or 10 mL), were: NanoMate/MS (25-1000 microg/L), r(2)=0.998; NanoMate/MS(2) (5-1000 microg/L), r(2)=0.9992; NanoMate/MS(3) (2.5-1000 microg/L), r(2)=0.9998. Reproducibility data (% RSD, N=5) for NanoMate/MS(n) mode ranged between 2.0 at 500 microg/L and 7.0 at 10 microg/L.

Effects of a Multidisciplinary Approach to Improve Volume of Diagnostic Material in CT-Guided Lung Biopsies.

PubMed

Ferguson, Philip E; Sales, Catherine M; Hodges, Dalton C; Sales, Elizabeth W

2015-01-01

Recent publications have emphasized the importance of a multidisciplinary strategy for maximum conservation and utilization of lung biopsy material for advanced testing, which may determine therapy. This paper quantifies the effect of a multidisciplinary strategy implemented to optimize and increase tissue volume in CT-guided transthoracic needle core lung biopsies. The strategy was three-pronged: (1) once there was confidence diagnostic tissue had been obtained and if safe for the patient, additional biopsy passes were performed to further increase volume of biopsy material, (2) biopsy material was placed in multiple cassettes for processing, and (3) all tissue ribbons were conserved when cutting blocks in the histology laboratory. This study quantifies the effects of strategies #1 and #2. This retrospective analysis comparing CT-guided lung biopsies from 2007 and 2012 (before and after multidisciplinary approach implementation) was performed at a single institution. Patient medical records were reviewed and main variables analyzed include biopsy sample size, radiologist, number of blocks submitted, diagnosis, and complications. The biopsy sample size measured was considered to be directly proportional to tissue volume in the block. Biopsy sample size increased 2.5 fold with the average total biopsy sample size increasing from 1.0 cm (0.9-1.1 cm) in 2007 to 2.5 cm (2.3-2.8 cm) in 2012 (P<0.0001). The improvement was statistically significant for each individual radiologist. During the same time, the rate of pneumothorax requiring chest tube placement decreased from 15% to 7% (P = 0.065). No other major complications were identified. The proportion of tumor within the biopsy material was similar at 28% (23%-33%) and 35% (30%-40%) for 2007 and 2012, respectively. The number of cases with at least two blocks available for testing increased from 10.7% to 96.4% (P<0.0001). The effect of this multidisciplinary strategy to CT-guided lung biopsies was effective in significantly increasing tissue volume and number of blocks available for advanced diagnostic testing.

Multi-source irradiation facility with improved space configuration for neutron activation analysis: Design optimization.

PubMed

Kotb, N A; Solieman, Ahmed H M; El-Zakla, T; Amer, T Z; Elmeniawi, S; Comsan, M N H

2018-05-01

A neutron irradiation facility consisting of six 241 Am-Be neutron sources of 30 Ci total activity and 6.6 × 10 7 n/s total neutron yield is designed. The sources are embedded in a cubic paraffin wax, which plays a dual role as both moderator and reflector. The sample passage and irradiation channel are represented by a cylindrical path of 5 cm diameter passing through the facility core. The proposed design yields a high degree of space symmetry and thermal neutron homogeneity within 98% of flux distribution throughout the irradiated spherical sample of 5 cm diameter. The obtained thermal neutron flux is 8.0 × 10 4 n/cm 2 .s over the sample volume, with thermal-to-fast and thermal-to-epithermal ratios of 1.20 and 3.35, respectively. The design is optimized for maximizing the thermal neutron flux at sample position using the MCNP-5 code. The irradiation facility is supposed to be employed principally for neutron activation analysis. Copyright © 2018 Elsevier Ltd. All rights reserved.

SU-F-T-49: Dosimetry Parameters and TPS Commissioning for the CivaSheet Directional Pd-103 Brachytherapy Source

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rivard, MJ

2016-06-15

Purpose: The CivaSheet is a new LDR Pd-103 brachytherapy device offering directional-radiation for preferentially irradiating malignancies with healthy-tissue sparing. Observations are presented on dosimetric characterization, TPS commissioning, and evaluation of the dosesuperposition- principle for summing individual elements comprising a planar CivaSheet Methods: The CivaSheet comprises individual sources (CivaDots, 0.05cm thick and 0.25cm diam.) inside a flexible bioabsorbable substrate with a 0.8cm center-to-center rectangular array. All non-radioactive components were measured to ensure accuracy of manufacturer-provided dimensional information. The Pd spatial distribution was gleaned from radioactive and inert samples, then modeled with the MCNP6 radiation-transport-code. A 6×6 array CivaSheet was modeled tomore » evaluate the dose superposition principle for treatment planning. Air-kerma-strength was estimated using the NIST WAFAC geometry. Absorbed dose was estimated in water with polar sampling covering 0.05≤r≤15cm in 0.05cm increments and 0°≤θ≤180° in 1° increments. These data were entered into VariSeed9.0 and tested for the dose-superposition-principle. Results: The dose-rate-constant was 0.579 cGy/h/U with g(r) determined along the rotational-axis of symmetry (0°) instead of 90°. gP(r) values at 0.1, 0.5, 2, 5, and 10cm were 1.884, 1.344, 0.558, 0.088, and 0.0046. F(r,θ) decreased between 0° and 180° by factors of 270, 23, and 5.1 at 0.1, 1, and 10cm. The highest dose-gradient was at 92°, changing by a factor of 3 within 1° due to Au-foil shielding. TPS commissioning from 0.1≤r≤11cm and 0°≤θ≤180° demonstrated 2% reproducibility of input data except at the high-dose-gradient where interpolations caused 3% differences. Dose superposition of CivaDots replicated a multi-source CivaSheet array within 2% except where another CivaDot was present. Following implantation, the device is not perfectly planar. TPS accuracy utilizing the dose-superposition-principle through geometric repositioning of CivaDots supersedes TPS limitations of intersource shielding effects Conclusion: Dosimetric characterization, source commissioning, and evaluation of the dose-superposition-principle with VariSeed9.0 permits treatment planning for the CivaSheet brachytherapy device. Research supported in part by CivaTech Oncology, Inc.« less

Electron microscopy and positron annihilation study of CdSe nanoclusters embedded in MgO

NASA Astrophysics Data System (ADS)

van Huis, M. A.; van Veen, A.; Schut, H.; Eijt, S. W. H.; Kooi, B. J.; De Hosson, J. Th. M.

2004-06-01

CdSe nanoclusters are created in MgO by means of co-implantation of 280 keV, 1 × 10 16 Cd ions cm -2 and 210 keV, 1 × 10 16 Se ions cm -2 in single crystals of MgO(0 0 1) and subsequent thermal annealing at a temperature of 1300 K. The structural properties and the orientation relationship between the CdSe and the MgO are investigated using cross-sectional transmission electron microscopy (XTEM). The crystal structure of the nanoclusters depends on their size. The smallest nanoclusters with a size below 5 nm have the cubic rocksalt crystal structure. The larger nanoclusters have a different (most likely the cubic sphalerite) crystal structure. The defect evolution in the sample after ion implantation and during thermal annealing is investigated using Doppler broadening positron beam analysis (PBA). The defect evolution in samples co-implanted with Cd and Se is compared to the defect evolution in samples implanted with only Cd or only Se ions.

Meltwater storage in low-density near-surface bare ice in the Greenland ice sheet ablation zone

NASA Astrophysics Data System (ADS)

Cooper, Matthew G.; Smith, Laurence C.; Rennermalm, Asa K.; Miège, Clément; Pitcher, Lincoln H.; Ryan, Jonathan C.; Yang, Kang; Cooley, Sarah W.

2018-03-01

We document the density and hydrologic properties of bare, ablating ice in a mid-elevation (1215 m a.s.l.) supraglacial internally drained catchment in the Kangerlussuaq sector of the western Greenland ice sheet. We find low-density (0.43-0.91 g cm-3, μ = 0.69 g cm-3) ice to at least 1.1 m depth below the ice sheet surface. This near-surface, low-density ice consists of alternating layers of water-saturated, porous ice and clear solid ice lenses, overlain by a thin (< 0.5 m), even lower density (0.33-0.56 g cm-3, μ = 0.45 g cm-3) unsaturated weathering crust. Ice density data from 10 shallow (0.9-1.1 m) ice cores along an 800 m transect suggest an average 14-18 cm of specific meltwater storage within this low-density ice. Water saturation of this ice is confirmed through measurable water levels (1-29 cm above hole bottoms, μ = 10 cm) in 84 % of cryoconite holes and rapid refilling of 83 % of 1 m drilled holes sampled along the transect. These findings are consistent with descriptions of shallow, depth-limited aquifers on the weathered surface of glaciers worldwide and confirm the potential for substantial transient meltwater storage within porous low-density ice on the Greenland ice sheet ablation zone surface. A conservative estimate for the ˜ 63 km2 supraglacial catchment yields 0.009-0.012 km3 of liquid meltwater storage in near-surface, porous ice. Further work is required to determine if these findings are representative of broader areas of the Greenland ice sheet ablation zone, and to assess the implications for sub-seasonal mass balance processes, surface lowering observations from airborne and satellite altimetry, and supraglacial runoff processes.

Exposure to airborne asbestos in thermal power plants in Mongolia.

PubMed

Damiran, Naransukh; Silbergeld, Ellen K; Frank, Arthur L; Lkhasuren, Oyuntogos; Ochir, Chimedsuren; Breysse, Patrick N

2015-01-01

Coal-fired thermal power plants (TPPs) in Mongolia use various types of asbestos-containing materials (ACMs) in thermal insulation of piping systems, furnaces, and other products. To investigate the occupational exposure of insulation workers to airborne asbestos in Mongolian power plants. Forty-seven air samples were collected from four power plants in Mongolia during the progress of insulation work. The samples were analyzed by phase contrast microscopy (PCM) and transmission electron microscopy (TEM). The average phase contrast microscopy equivalent (PCME) asbestos fiber concentration was 0·93 f/cm(3). Sixteen of the 41 personal and one of the area samples exceeded the United States Occupational Safety and Health Administration (US OSHA) short-term exposure limit of 1·0 f/cm(3). If it is assumed that the short-term samples collected are representative of full-shift exposure, then the exposures are approximately 10 times higher than the US OSHA 8-hour permissible exposure limit of 0·1 f/cm(3). Power plant insulation workers are exposed to airborne asbestos at concentrations that exceed the US OSHA Permissible Exposure Limit. Action to mitigate the risks should be taken in Mongolia.

Li-Diffusion in Spinel Li[Ni1/2Mn3/2]O4 Powder and Film Studied with μ+SR

NASA Astrophysics Data System (ADS)

Sugiyama, Jun; Nozaki, Hiroshi; Umegaki, Izumi; Mukai, Kazuhiko; Cottrell, Stephen P.; Shiraki, Susumu; Hitosugi, Taro; Sassa, Yasmine; Suter, Andreas; Salman, Zaher; Prokscha, Thomas; Månsson, Martin

A dynamic behavior in spinel Li[Ni1/2Mn3/2]O4 has been studied with μ+SR measurements in film and powder samples in the temperature range between 5 and 500 K. Both samples exhibited a broad ferromagnetic transition below 120 K, indicating the random distribution of Ni and Mn ions at the octahedral 16d site. Above 150 K, the ZF-μ+SR spectrum showed a dynamic behavior well explained by a dynamic Kubo-Toyabe function. Assuming a jump diffusion of Li+ at the tetrahedral 8a site to the vacant octahedral 16c site, a diffusion coefficient of Li+ is estimated as ˜5 × 10-11 cm2/s at 300 K and ˜8 × 10-11 cm2/s at 350 K and ˜14 × 10-11 cm2/s at 400 K, with thermal activation energy Ea ˜ 0.1 eV.

Reduction of Brochothrix thermosphacta on beef surfaces following immobilization of nisin in calcium alginate gels.

PubMed

Cutter, C N; Siragusa, G R

1996-07-01

Lean and adipose beef carcass tissues inoculated with Brochothrix thermosphacta (BT) (approx. 4.50 log10 cfu cm-2) were left untreated (U) or treated with 100 micrograms ml-1 nisin (N), calcium alginate (A) or 100 micrograms ml-1 nisin immobilized in a calcium alginate gel (AN). Tissue samples were refrigerated after treatments and bacterial populations and nisin activity were determined at 0, 1, 2 and 7 d. U, A and N treatments of lean and adipose tissues did not suppress bacterial growth ( > 6 log10 cfu cm-2 by day 7) while treatments of lean and adipose tissues with AN suppressed bacteria ( > 2.42 log10 cfu cm-2 by day 7). Bacteriocin titres from both tissues were higher in AN vs N samples after the 7 d incubation. This study demonstrates that immobilization of nisin in a gel may be a more effective delivery system of a bacteriocin to the carcass surface than direct application.

Dosimetric impact of cylinder size in high-dose rate vaginal cuff brachytherapy (VCBT) for primary endometrial cancer.

PubMed

Zhang, Hualin; Gopalakrishnan, Mahesh; Lee, Plato; Kang, Zhuang; Sathiaseelan, Vythialingam

2016-09-08

The purpose of this study was to evaluate the dosimetric impact of cylinder size in high-dose-rate (HDR) vaginal cuff brachytherapy (VCBT). Sample plans of HDR VCBT in a list of cylinders ranging from 2.5 to 4 cm in diameter at 0.5 cm incre-ment were created and analyzed. The doses were prescribed either at the 0.5cm depth with 5.5 Gy for 4 fractions or at the cylinder surface with 8.8 Gy for 4 frac-tions, in various treatment lengths. A 0.5 cm shell volume called PTV_Eval was contoured for each plan and served as the target volume for dosimetric evaluation. The cumulative and differential dose volume histograms (c-DVH and d-DVH), mean doses (D-mean) and the doses covering 90% (D90), 10% (D10), and 5% (D5) of PTV_Eval were calculated. In the 0.5 cm depth regimen, the DVH curves were found to have shifted toward the lower dose zone when a larger cylinder was used, but in the surface regimen the DVH curves shifted toward the higher dose zone as the cylinder size increased. The D-means of the both regimens were between 6.9 and 7.8 Gy and dependent on the cylinder size but independent of the treatment length. A 0.5 cm variation of diameter could result in a 4% change of D-mean. Average D90s were 5.7 (ranging from 5.6 to 5.8 Gy) and 6.1 Gy (from 5.7 to 6.4 Gy), respectively, for the 0.5 cm and surface regimens. Average D10 and D5 were 9.2 and 11 Gy, respectively, for the 0.5 cm depth regimen, and 8.9 and 9.7 Gy, respectively, for the surface regimen. D-mean, D90, D10, and D5 for other prescription doses could be calculated from the lookup tables of this study. Results indicated that the cylinder size has moderate dosimetric impact, and that both regimens are comparable in dosimetric quality. © 2016 The Authors.

Dark Current Characterization of SW HgCdTe IRFPAs Detectors on Si Substrate with Long Time Integration

NASA Astrophysics Data System (ADS)

Song, P. Y.; Ye, Z. H.; Huang, A. B.; Chen, H. L.; Hu, X. N.; Ding, R. J.; He, L.

2016-09-01

The dark currents of two short wave (SW) HgCdTe infrared focal plane arrays (IRFPA) detectors hybridized with direct injection (DI) readout and capacitance transimpedance amplifier (CTIA) with long time integration were investigated. The cutoff wavelength of the two SW IRFPAs is about 2.6 μm at 84 K. The dark current densities of DI and CTIA samples are approximately 8.0 × 10-12 A/cm2 and 7.2 × 10-10 A/cm2 at 110 K, respectively. The large divergence of the dark current density might arise from the injection efficiency difference of the two readouts. The low injection efficiency of the DI readout, compared with the high injection efficiency of the CTIA readout at low temperature, makes the dark current density of the DI sample much lower than that of the CTIA sample. The experimental value of injection efficiency of the DI sample was evaluated as 1.1% which is consistent with its theoretical value.

Differences of skin morphology in Bos indicus, Bos taurus, and their crossbreds

NASA Astrophysics Data System (ADS)

Jian, Wang; Duangjinda, M.; Vajrabukka, C.; Katawatin, Suporn

2014-08-01

Cutaneous evaporation is the main avenue by which cattle dissipate heat via the involvement of sweat glands and other skin components. The difference in skin morphology between B. indicus and B. taurus has been recognized, as well as differences in their ability to tolerate heat. The objective of this study was to compare skin morphology between B. indicus, B. taurus, and their crossbreds. Skin samples of Sahiwal ( B. indicus) ( n = 10, reddish brown skin) and Holstein Friesian (HF) ( B. taurus) ( n = 10, black and white skin) and crossbred of HF75% ( n = 10, black and white skin) and HF87.5 % ( n = 10, black and white skin) were biopsied for histological study, followed by measurement of skin components. The results indicated that breed significantly affected sweat gland morphology. The shape of the sweat gland, as indicated by the ratio of length/diameter, in Sahiwal was baggier in shape compared to HF (5.99 and 9.52) while values for crossbreds were intermediate (7.82, 8.45). The density and volume of sweat glands in Sahiwal (1,058 glands/cm2; 1.60 μ3 × 10-6) were higher than in HF (920 glands/cm2; 0.51 μ3x10-6) and crossbreds, both HF 75 % (709 glands/cm2; 0.68 μ3 × 10-6) and HF 87.5 % (691 glands/cm2; 0.61 μ3 × 10-6) respectively. However, capillary surface area was greater for HF (2.07 cm2) compared to Sahiwal (1.79 cm2); accordingly, the lower genetic fraction of HF in crossbred cattle showed less capillary surface area (1.83 and 1.9 cm2 for HF75% and HF87.5 %) ( P < 0.01). Nerve density was not significantly different between Sahiwal and HF but was higher in the crossbred ( P < 0.01) cattle. Moreover, the effect of skin color (black and white) was evaluated and it was found that there was an interaction ( P < 0.01) between breed and skin color on the skin components. This study reveals that there are differences in skin morphology among B. indicus, B. taurus and their crossbreds, with these differences being more or less related to the genetic fraction of HF. This may imply that capability for cutaneous evaporative heat loss and tolerance to heat in crossbred cattle could be related to skin morphology.

40 CFR 89.412 - Raw gaseous exhaust sampling and analytical system description.

Code of Federal Regulations, 2013 CFR

2013-07-01

...) Sample probe. (1) The sample probe shall be a straight, closed-end, stainless steel, multi-hole probe... wall thickness of the probe shall not be greater than 0.10 cm. The fitting that attaches the probe to the exhaust pipe shall be as small as practical in order to minimize heat loss from the probe. (2) The...

40 CFR 89.412 - Raw gaseous exhaust sampling and analytical system description.

Code of Federal Regulations, 2014 CFR

2014-07-01

...) Sample probe. (1) The sample probe shall be a straight, closed-end, stainless steel, multi-hole probe... wall thickness of the probe shall not be greater than 0.10 cm. The fitting that attaches the probe to the exhaust pipe shall be as small as practical in order to minimize heat loss from the probe. (2) The...

40 CFR 89.412 - Raw gaseous exhaust sampling and analytical system description.

Code of Federal Regulations, 2012 CFR

2012-07-01

...) Sample probe. (1) The sample probe shall be a straight, closed-end, stainless steel, multi-hole probe... wall thickness of the probe shall not be greater than 0.10 cm. The fitting that attaches the probe to the exhaust pipe shall be as small as practical in order to minimize heat loss from the probe. (2) The...

Comparison of patient-specific internal gross tumor volume for radiation treatment of primary esophageal cancer based separately on three-dimensional and four-dimensional computed tomography images.

PubMed

Wang, W; Li, J; Zhang, Y; Li, F; Xu, M; Fan, T; Shao, Q; Shang, D

2014-01-01

To compare the target volume, position and matching index of the patient-specific internal gross tumor volume (IGTV) based on three-dimensional (3D) and four-dimensional (4D) computed tomography (CT) images for primary esophageal cancer. Twenty-nine patients with primary thoracic esophageal cancer underwent 3DCT and 4DCT scans during free breathing. IGTVs were constructed using three approaches: combining the gross target volumes from the 10 respiratory phases of the 4DCT dataset to produce IGTV10 ; IGTV2 was acquired by combining the two extreme phases; and IGTV3D was created from the 3DCT-based gross target volume by enlarging the 95th percentile of motion in each direction measured by the 4DCT. 0.16 cm lateral (LR), 0.14 cm anteroposterior (AP) and 0.29 cm superoinferior (SI) in the upper; 0.18 cm LR, 0.10 cm AP and 0.63 cm SI in the middle; and 0.40 cm LR, 0.58 cm AP and 0.82 cm in the lower thoracic esophagus could account for 95% of respiratory-induced tumor motion. The centroid position shift between IGTV10 and IGTV2 was all below 0.10 cm, and less than 0.20 cm between IGTV10 and IGTV3D . IGTV10 was bigger than IGTV2 ; the mean value of matching index for IGTV2 to IGTV10 was 0.87 ± 0.05, 0.85 ± 0.06 and 0.83 ± 0.05 for upper, middle and distal thoracic esophageal tumors, respectively, and just 0.57 ± 0.11, 0.56 ± 0.13 and 0.40 ± 0.03 between IGTV3D and IGTV10 . 4DCT-based IGTV10 is a reasonable patient-specific IGTV for primary thoracic esophageal cancer, and IGTV2 is considered as an acceptable alternative to IGTV10 . However, it seems unreasonable to use IGTV3D substitute IGTV10 . © 2013 Wiley Periodicals, Inc. and the International Society for Diseases of the Esophagus.

Propane spectral resolution enhancement by the maximum entropy method

NASA Technical Reports Server (NTRS)

Bonavito, N. L.; Stewart, K. P.; Hurley, E. J.; Yeh, K. C.; Inguva, R.

1990-01-01

The Burg algorithm for maximum entropy power spectral density estimation is applied to a time series of data obtained from a Michelson interferometer and compared with a standard FFT estimate for resolution capability. The propane transmittance spectrum was estimated by use of the FFT with a 2 to the 18th data sample interferogram, giving a maximum unapodized resolution of 0.06/cm. This estimate was then interpolated by zero filling an additional 2 to the 18th points, and the final resolution was taken to be 0.06/cm. Comparison of the maximum entropy method (MEM) estimate with the FFT was made over a 45/cm region of the spectrum for several increasing record lengths of interferogram data beginning at 2 to the 10th. It is found that over this region the MEM estimate with 2 to the 16th data samples is in close agreement with the FFT estimate using 2 to the 18th samples.

Simultaneous determination of eleven preservatives in cosmetics by micellar electrokinetic chromatography.

PubMed

Wang, Ping; Ding, Xiaojing; Li, Yun; Yang, Yuanyuan

2012-01-01

A new method for the simultaneous quantitation of 11 preservatives-imidazolidinyl urea, benzyl alcohol, dehydroacetic acid, sorbic acid, phenoxyethanol, benzoic acid, salicylic acid, and four parabens (methyl, ethyl, propyl, and butyl)-in cosmetics by micellar electrokinetic capillary chromatography was established and validated. The separation was performed using an uncoated fused-silica capillary (50 pm id x 60.2 cm, effective length 50 cm) with a running buffer consisting of 15 mmol/L sodium tetraborate, 60 mmol/L boric acid, and 100 mmol/L sodium dodecyl sulfate. A 1:10 dilution of the running buffer was used as the sample buffer to extract the cosmetic samples. The key factors, such as the concentration and pH of the running and sample buffers, which influence quantitative analysis of the above 11 preservatives in cosmetic samples, were investigated in detail. The linear ranges of the calibration curves for imidazolidinyl urea and the other 10 preservatives were 50-1000 and 10-200 mg/L, respectively. The correlation coefficients of the standard curves were all higher than 0.999. The recoveries at the concentrations studied ranged from 93.0 to 102.7%. RSDs were all less than 5%. The new method with simple sample pretreatment met the needs for routine analysis of the 11 preservatives in cosmetics.

Improved electrical properties of n-type SiGe alloys

NASA Technical Reports Server (NTRS)

Scoville, A. N.; Bajgar, Clara; Vandersande, Jan; Fleurial, Jean-Pierre

1992-01-01

The effect of changes in the carrier concentration and mobility for heavily doped n-type SiGe on the electrical power factor has been investigated. It has been shown that power factors of 37-40 microV/cm-K-squared can be achieved with carrier concentrations of 2.0 - 2.5 x 10 exp 20/cu cm and mobilities of 38-40 sq cm/V-sec. Many samples with suitable carrier concentration do not have high mobilities and some rationale for this behavior is presented. Initial results are presented on fabrication of n-type samples from ultrafine powders. The emphasis in this work is to achieve thermal conductivity reductions by adding inert particles to scatter midfrequency phonons.

Spatial distribution of topsoil magnetic susceptibility in Sawahlunto City, West Sumatera

NASA Astrophysics Data System (ADS)

Afdal; Wahyuni, E. S.

2018-03-01

A research to determine the spatial distribution of top soil magnetic suceptibility at Sawahlunto City, West Sumatra has been conducted. The top soil samples were taken at four locations ie the downtown area, the steam power plant area, the agricultural area, and coal mine area. At each location, the soil samples were taken at 10 points at a depth of 20 cm. Magnetic susceptibility were measured using Bartington MS2B Magnetic Susceptibility Meter. The topsoil samples from Sawahlunto city have relatively low average value of the magnetic susceptibility that is 67.0×10-8 m3/kg. The magnetic susceptibility of topsoil samples from downtown area have the average and the highest value of magnetic susceptibility (100.6×10-8 and 259.9×10-8 m3/kg), and followed by sample from the steam power plant area (98.4×10-8 and 258.0×10-8 m3/kg), the agricultural area (56.2×10-8 and 83.7×10-8 m3/kg), and coal mine area (12.9×10-8 and 26.8×10-8 m3/kg). Soil samples from the steam power plant area have the widest range of magnetic susceptibility value range from 0.3 × 10-8 to 258.0 × 10-8 m3/kg.

Spatial and Temporal Variability of Hydraulic Properties in the Russian River Streambed, Central Sonoma, County, CA

NASA Astrophysics Data System (ADS)

Laforce, M.; Gorman, P.; Constantz, J.

2004-12-01

Temporal and spatial variations of flux and vertical hydraulic conductivity were measured in the Russian River streambed in Sonoma County, California. In-situ vertical hydraulic conductivity measurements were made using a modified seepage meter, equipped with mini-piezometers and sediment was collected with a bucket and shovel. We sampled three different streambed (near bank, midpoint, and thalweg) locations at five different sample locales throughout the river system. Vertical hydraulic conductivity of the streambed ranged from 8.55X10-5 cm/sec to 1.52X10-1 cm/sec. Flux varied from -240 to 600 cm/day, which indicates both gaining and losing reaches of the stream occur in our study area. There was not a strong correlation (r=0.08) between particle size distribution and vertical hydraulic conductivity. Our findings will assist the Sonoma County Water Agency in managing water needs for the citizens of Sonoma County.

Effect of Product Dimensions and Surface Browning Method on Salmonella Contamination in Frozen, Surface-Browned, Breaded Chicken Products Treated with Antimicrobials.

PubMed

Moschonas, Galatios; Geornaras, Ifigenia; Stopforth, Jarret D; Woerner, Dale R; Belk, Keith E; Smith, Gary C; Sofos, John N

2015-12-01

Not-ready-to-eat breaded chicken products formulated with antimicrobial ingredients were tested for the effect of sample dimensions, surface browning method and final internal sample temperature on inoculated Salmonella populations. Fresh chicken breast meat portions (5 × 5 × 5 cm), inoculated with Salmonella (7-strain mixture; 5 log CFU/g), were mixed with (5% v/w total moisture enhancement) (i) distilled water (control), (ii) caprylic acid (CAA; 0.0625%) and carvacrol (CAR; 0.075%), (iii) CAA (0.25%) and ε-polylysine (POL; 0.5%), (iv) CAR (0.15%) and POL (0.5%), or (v) CAA (0.0625%), CAR (0.075%) and POL (0.5%). Sodium chloride (1.2%) and sodium tripolyphosphate (0.3%) were added to all treatments. The mixtures were then ground and formed into 9 × 5 × 3 cm (150 g) or 9 × 2.5 × 2 cm (50 g) portions. The products were breaded, browned in (i) an oven (208 °C, 15 min) or (ii) deep fryer (190 °C, 15 s), packaged, and stored at -20 °C (8 d). Overall, maximum internal temperatures of 62.4 ± 4.0 °C (9 × 2.5 × 2 cm) and 46.0 ± 3.0 °C (9 × 5 × 3 cm) were reached in oven-browned samples, and 35.0 ± 1.1 °C (9 × 2.5 × 2 cm) and 31.7 ± 2.6 °C (9 × 5 × 3 cm) in fryer-browned samples. Irrespective of formulation treatment, total (after frozen storage) reductions of Salmonella were greater (P < 0.05) for 9 × 2.5 × 2 cm oven-browned samples (3.8 to at least 4.6 log CFU/g) than for 9 × 5 × 3 cm oven-browned samples (0.7 to 2.5 log CFU/g). Product dimensions did not (P ≥ 0.05) affect Salmonella reductions (0.6 to 2.8 log CFU/g) in fryer-browned samples. All antimicrobial treatments reduced Salmonella to undetectable levels (<0.3 log CFU/g) in oven-browned 9 × 2.5 × 2 cm samples. Overall, the data may be useful for the selection of antimicrobials, product dimensions, and surface browning methods for reducing Salmonella contamination. © 2015 Institute of Food Technologists®

The 15th Internatonal Conference Quality in Resarch (Qir) 2017 Preparation and Ionic Conductivity of Li3.9Ca0.1Ti5O12 Using Waste Chicken Eggshells as ca Source for Anode Material of Lithium-Ion Batteries

NASA Astrophysics Data System (ADS)

Subhan, Achmad; Setiawan, Dedy; Ahmiatri Saptari, Sitti

2018-03-01

Li3.9Ca0.1Ti5O12 has been synthesized as anode material for lithium-ion batteries parallel with Li4Ti5O12 anode material using solid state reaction method in an air atmosphere. LiOH.H2O, TiO2, and waste chicken eggshells in the form of CaCO3 were chosen as sources of Li, Ti, and Ca respectively and prepared using stoichiometric. The phase structure, morphology, and electrochemical impedance of as-prepared samples were characterized using XRD, SEM, and EIS. The XRD characterization revealed that in Li3.9Ca0.1Ti5O12 sample, all amount of dopant had entered the lattice structure of Li4Ti5O12. The EDX image also detect the existence of Ca in the structure of Li3.9Ca0.1Ti5O12. The EIS characterization revealed that the Li3.9Ca0.1Ti5O12 sample had lower electrochemical impedance compared to the Li4Ti5O12 sample. The diffusion coefficient were obtained by Faraday’s method, and exhibited that the Li3.9Ca0.1Ti5O12 sample (1.46986 × 10-12 cm2/s) had higher ionic conductivity than the Li4Ti5O12 sample (4.40995 × 10-16 cm2/s). According to the cycle performance test, the Li3.9Ca0.1Ti5O12 sample also had higher charge-discharge capacity and stability compared to the Li4Ti5O12 sample.

Hazard analysis and critical point identification at Abiss slaughter house in Alexandria.

PubMed

Gomaa, N F; El-Derea, H B; ElI-Adham, E

2003-01-01

The purpose of this study is to identify potential hazards associated with animal slaughtering and how could these affect the microbiological count of carcasses, and to describe the use of HACCP to improve the microbiological count of fresh meat. Hazards were detected by observing the different steps of animal slaughter and then filling a prepared red meat slaughterhouse score sheet. The microbiological load was determined through testing 112 swab samples taken from the surface of carcasses in addition to 21 samples from hands, knives, tap water and air. Results showed that most of the parameters of the score sheet observed for evaluating hygienic operations were classified as being of maximum risk C. The aerobic plate count enterobacteriacea, mold and yeast and staphylococci increased insignificantly after cutting to 9.7x10(2), 6.4x10, 2.6x10(2), and 3.7x10 cfu/cm2, respectively. Washing of the carcasses decreased counts insignificantly to 6.4x10(2), 2.0x10, 1.7x10(2), and 2.0x10 cfu/cm2, respectively. The microbiological count of air samples at quiet hours were lower insignificantly than those at busy hours. Subsequently a HACCP system was designed based on these microbial studies, observations of current practices within the slaughterhouse and relevant literature and following the 7 principles of HACCP.

Recharging processes, radiation induced strain and changes of OH - bands under H + ion implantation in Ti doped lithium niobate

NASA Astrophysics Data System (ADS)

Kumar, P.; Moorthy Babu, S.; Bhaumik, I.; Ganesamoorthy, S.; Karnal, A. K.; Kumar, Praveen; Rodrigues, G. O.; Sulania, I.; Kanjilal, D.; Pandey, A. K.; Raman, R.

2010-01-01

A systematic analysis of variations in structural and optical characteristics of Z-cut plates of titanium doped congruent lithium niobate single crystals implanted with 120 keV proton beam at various fluences of 10 15, 10 16 and 10 17 protons/cm 2 is presented. Through, high resolution X-ray diffraction, atomic force microscopy, Fourier transform infrared and UV-visible-NIR analysis of congruent lithium niobate, the correlation of properties before and after implantation are discussed. HRXRD (0 0 6) reflection by Triple Crystal Mode shows that both tensile and compressive strain peak are produced by the high fluence implantation. A distinct tensile peak was observed from implanted region for a fluence of 10 16 protons/cm 2. AFM micrographs indicate mountain ridges, bumps and protrusions on target surface on implantation. UV-visible-NIR spectra reveal an increase in charge transfer between Ti 3+/Ti 4+ and ligand oxygen for implantation with 10 15 protons/cm 2, while spectra for higher fluence implanted samples show complex absorption band in the region from 380-1100 nm. Variations of OH - stretching vibration mode were observed for cLN Pure, cLNT2% virgin, and implanted samples with FTIR spectra. The concentration of OH - ion before and after implantation was calculated from integral absorption intensity. The effect of 120 keV proton implantation induced structural, surface and optical studies were correlated.

Degradation and persistence of cotton pesticides in sandy loam soils from Punjab, Pakistan.

PubMed

Tariq, Muhammad Ilyas; Afzal, Shahzad; Hussain, Ishtiaq

2006-02-01

The present study evaluated the influence of temperature, moisture, and microbial activity on the degradation and persistence of commonly used cotton pesticides, i.e., carbosulfan, carbofuran, lambda-cyhalothrin, endosulfan, and monocrotophos, with the help of laboratory incubation and lysimeter studies on sandy loam soil (Typic Ustocurepts) in Pakistan. Drainage from the lysimeters was sampled on days 49, 52, 59, 73, 100, 113, and 119 against the pesticide application on days 37, 63, 82, 108, and 137 after the sowing of cotton. Carbofuran, monocrotophos, and nitrate were detected in the drainage samples, with an average value, respectively, of 2.34, 2.6 microg/L, and 15.6 mg/L for no-tillage and 2.16, 2.3 microg/L, and 13.4 mg/L for tillage. In the laboratory, pesticide disappearance kinetics were measured with sterile and nonsterile soils from 0 to 10 cm in depth at 15, 25, and 35 degrees C and 50% and 90% field water capacities. Monocrotophos and carbosulfan dissipation followed first-order kinetics while others followed second-order kinetics. The results of incubation studies showed that temperature and moisture contents significantly reduced the t(1/2) (half-life) values of pesticides in sterile and nonsterile soil, but the effect of microbial activity was nearly significant that might be due to less organic carbon (0.3%). The presence of carbofuran and monocrotophos in the soil profile (0-10, 10-30, 30-60, 60-90, 90-150 cm) and the higher concentrations of endosulfan and lambda-cyhalothrin in the top layer (0-10 cm) showed the persistence of the pesticides. The detection of endosulfan and lambda-cyhalothrin in the 10-30 cm soil layer might be due to preferential flow. The data generated from this study could be helpful for risk assessment studies of pesticides and for validating pesticide transport models for sandy loam soils in cotton-growing areas of Pakistan.

Biophysical Controls over Carbon and Nitrogen Stocks in Desert Playa Wetlands

NASA Astrophysics Data System (ADS)

McKenna, O. P.; Sala, O. E.

2014-12-01

Playas are ephemeral desert wetlands situated at the bottom of closed catchments. Desert playas in the Southwestern US have not been intensively studied despite their potential importance for the functioning of desert ecosystems. We want to know which geomorphic and ecological variables control of the stock size of soil organic carbon, and soil total nitrogen in playas. We hypothesize that the magnitude of carbon and nitrogen stocks depends on: (a) catchment size, (b) catchment slope, (d) catchment vegetation cover, (e) bare-ground patch size, and (f) catchment soil texture. We chose thirty playas from across the Jornada Basin (Las Cruces, NM) ranging from 0.5-60ha in area and with varying catchment characteristics. We used the available 5m digital elevation map (DEM) to calculate the catchment size and catchment slope for these thirty playas. We measured percent cover, and patch size using the point-intercept method with three 10m transects in each catchment. We used the Bouyoucos-hydrometer soil particle analysis to determine catchment soil texture. Stocks of organic carbon and nitrogen were measured from soil samples at four depths (0-10 cm, 10-30 cm, 30-60 cm, 60-100 cm) using C/N combustion analysis. In terms of nitrogen and organic carbon storage, we found soil nitrogen values in the top 10cm ranging from 41.963-214.365 gN/m2, and soil organic carbon values in the top 10cm ranging from 594.339-2375.326 gC/m2. The results of a multiple regression analysis show a positive relationship between catchment slope and both organic carbon and nitrogen stock size (nitrogen: y= 56.801 +47.053, R2=0.621; organic carbon: y= 683.200 + 499.290x, R2= 0.536). These data support our hypothesis that catchment slope is one of factors controlling carbon and nitrogen stock in desert playas. We also applied our model to the 69 other playas of the Jornada Basin and estimated stock sizes (0-10cm) between 415.07-447.97 Mg for total soil nitrogen and 4627.99-5043.51 Mg for soil organic carbon.

VizieR Online Data Catalog: 6 & 1.3cm deep VLA obs. toward 58 high-mass SFRs (Rosero+, 2016)

NASA Astrophysics Data System (ADS)

Rosero, V.; Hofner, P.; Claussen, M.; Kurtz, S.; Cesaroni, R.; Araya, E. D.; Carrasco-Gonzalez, C.; Rodriguez, L. F.; Menten, K. M.; Wyrowski, F.; Loinard, L.; Ellingsen, S. P.

2017-01-01

VLA continuum observations (project codes 10B-124 and 13B-210) at 6 and 1.3cm were made for all sources in the sample. The 6cm observations were made in the A configuration between 2011 June and August, providing a typical angular resolution of about 0.4". The 1.3cm observations were made in the B configuration, acquiring the first half of the data between 2010 November and 2011 May, and the second half between 2013 November and 2014 January. (2 data files).

Properties and variability of soil and trench fill at an arid waste-burial site

USGS Publications Warehouse

Andraski, Brian J.

1996-01-01

Arid sites commonly are assumed to be ideal for long-term isolation of wastes. Information on properties and variability of desert soils is limited, however, and little is known about how the natural site environment is altered by installation of a waste facility. During fall construction of two test trenches next to the waste facility on the Amargosa Desert near Beatty, NV, samples were collected to: (i) characterize physical and hydraulic properties of native soil (upper 5 m) and trench fill, (ii) determine effects of trench construction on selected properties and vertical variability of these properties, and (iii) develop conceptual models of vertical variation within the soil profile and trench fill. Water retention was measured to air dryness (ψ = 2 × 106 cm water suction). The 15 300-cm pressure-plate data were omitted from the analysis because water-activity measurements showed the actual suction values were significantly less than the expected 15 300-cm value (avg. difference = 8550 ± 2460 cm water). Trench construction significantly altered properties and variability of the natural site environment. For example, water content ranged from 0.029 to 0.041 m3 m-3 for fill vs. 0.030 to 0.095 m3 m-3 for soil; saturated hydraulic conductivity was ≈ 10-4 cm s-1 for fill vs. 10-2 to ≈ 10-4 cm s-1 for soil. Statistical analyses showed that the native soil may be represented by three major horizontal components and the fill by a single component. Under initial conditions, calculated liquid conductivity (Kl) plus isothermal vapor conductivity (Kv) for the upper two soil layers and the trench fill was ≈ 10-13 cm s-1, and Kl was ≤ Kv. For the deeper (2–5 m) soil, total conductivity was ≈ 10-10 cm s-1, and Kl was >Kv. This study quantitatively describes hydraulic characteristics of a site using data measured across a water-content range that is representative of arid conditions, but is seldom studied.

Transport of atrazine and dicamba through silt and loam soils

USGS Publications Warehouse

Tindall, James A.; Friedel, Michael J.

2016-01-01

The objectives of this research were to determine the role of preferential flow paths in the transport of atrazine (2-chloro-4-(ethylamino)-6-(isopropylamino)-s-triazine) and dicamba (3-6-dichloro-2-methoxybenzoic acid) through silt and loam soils overlying the High Plains aquifer in Nebraska. In a previous study, 3 of 6 study areas demonstrated high percentages of macropores; those three areas were used in this study for analysis of chemical transport. As a subsequent part of the study, 12 intact soil cores (30-cm diameter by 40-cm height), were excavated sequentially, two from each of the following depths: 0-40cm and 40-80cm. These cores were used to study preferential flow characteristics using dye staining and to determine hydraulic properties. Two undisturbed experimental field plots, each with a 3-m2 surface area, were installed in three study areas in Nebraska. Each was instrumented with suction lysimeters and tensiometers at depths of 10cm to 80cm in 10-cm increments. Additionally, each plot was planted with corn (Zea mays). A neutron probe access tube was installed in each plot to determine soil w ater content at 15-cm intervals. All plots were enclosed w ith a raised frame (of 8-cm height) to prevent surface runoff. All suction lysimeters were purged monthly for three months and were sampled immediately prior to pre-plant herbicide application to obtain background chemical concentrations. Atrazine and dicamba moved rapidly through the soil, but only after a heavy rainfall event, probably owing to the presence of preferential flow paths and lack of microbial degradation in these soil areas. Staining of laboratory cores showed a positive correlation between the percent area stained by depth and the subsequent breakthrough of Br- in the laboratory and leaching of field-applied herbicides owing to large rainfall events. Suction lysimeter samples in the field showed increases in concentrations of herbicides at depths where laboratory data indicated greater percentages of what appeared to be preferential flow paths. Concentrations of atrazine and dicamba exceeding 0.30 and 0.05µg m1-1 were observed at depths of 10-30cm and 50-70cm after two months following heavy rainfall events. It appears from the laboratory experiment that preferential flow paths were a significant factor in transport of atrazine and dicamba.

The analysis of soil characteristics near the animal feed and fertiliser mill using the Bartington

NASA Astrophysics Data System (ADS)

Azhari, Adinda Syifa; Agustine, Eleonora; Fitriani, Dini

2017-07-01

Industrial activities have the potential to make pollution in agricultural land, the waste contains poisonous material and it is dangerous for the environment. In general, waste from factory is dumped directly into the river, but in the current study an object that is going to be conscientious is soil on around mill. There are three sampling sites are around fertilizer plants, feed mills and original uncontaminated soil. This research has been conducted to assess the impact of pollution resulting from the two mills for the environment. Physical parameter that used is magnetic susceptibility. Sampling was conducted using the method of magnetic susceptibility of rock to see the value of low frequency (lf) and shows Frequency Dependent (fd%) using the MS2B Bartington. The results from this study is at a location close to the fertilizer plant at a depth of 0-5 cm has a value susceptibility low frequency ( lf)=187.1 - 494.8, fd (%)=1.37 - 2:46, at a depth of 6-10 cm susceptibility value of low frequency (lf)=211 - 832.7,fd (%)=1.04 - 5.37. Results in the area of animal feed mill at a depth of 0-5 cm value susceptibility low frequency (lf)=111.9 - 325.7, fd (%)=0.8 - 3.57, at a depth of 6-10 cm value susceptibility low frequency (lf)=189.2 to 386.8,fd (%)=0.33 - 3.7. Results in the original soil at a depth of 0-5 cm susceptibility value of low frequency (lf)=1188.7 - 2237.8,fd (%)=2.75 - 4.65, at a depth of 6-10 cm value susceptibility low frequency (lf)=977.7 - 2134.7,fd (%)=3.06 - 6.21. The highest value was in the arealf original, shows the area has a high mineral content andlf lows were in the area near the factory fodder it is caused by high pollution, resulting in lower mineral content in the soil.

Evaluation of consumable household products for decontaminating retail skinless, boneless chicken breasts.

PubMed

McKee, L H; Neish, L; Pottenger, A; Flores, N; Weinbrenner, K; Remmenga, M

2005-03-01

The effect of 15 consumable products, including juices, wines, and vinegar, used as rinsing agents on microbial loads of retail skinless, boneless chicken breasts was evaluated in two studies. Ten breasts were rinsed for 1 min with each solution. Samples were swabbed before and after rinsing with a cellulose sponge and evaluated for total aerobic (APC), total coliform (TCC), and generic Escherichia coli counts by Petrifilm methods. No differences were found in initial APC or TCC in either study, with initial mean APC ranging from 5.30 to 7.05 log CFU/cm2 and initial mean TCC ranging from 2.21 to 3.36 log CFU/cm2. In study 1, the APC for breasts rinsed with distilled white vinegar (3.22 log CFU/cm2) was lower than for those rinsed with all other solutions except cranberry juice cocktail (3.86 log CFU/cm2). The TCC for breasts rinsed with distilled white vinegar (0.00 log CFU/cm2) and cranberry juice cocktail (0.20 log CFU/cm2) were lower than those for all other solutions except 10% NaCl (0.43 log CFU/cm2) and 10% NaHCO3 (0.48 log CFU/cm2). In study 2, APC values for breasts rinsed with red wine (5.29 log CFU/cm2) and white wine (5.32 log CFU/cm2) were lower than for breasts rinsed with the other three solutions. The TCC after rinsing with chicken broth (4.48 log CFU/cm2) was higher than for all other solutions except Italian dressing. Although distilled white vinegar was the most effective rinsing agent, all solutions produced lower counts after rinsing, indicating that consumers could use rinsing to remove microorganisms from chicken breast surfaces prior to cooking.

In vivo percutaneous absorption of boric acid, borax, and disodium octaborate tetrahydrate in humans compared to in vitro absorption in human skin from infinite and finite doses.

PubMed

Wester, R C; Hui, X; Hartway, T; Maibach, H I; Bell, K; Schell, M J; Northington, D J; Strong, P; Culver, B D

1998-09-01

Literature from the first half of this century report concern for toxicity from topical use of boric acid, but assessment of percutaneous absorption has been impaired by lack of analytical sensitivity. Analytical methods in this study included inductively coupled plasma-mass spectrometry which now allows quantitation of percutaneous absorption of 10B in 10B-enriched boric acid, borax, and disodium octaborate tetrahydrate (DOT) in biological matrices. This made it possible, in the presence of comparatively large natural dietary boron intakes for the in vivo segment of this study, to quantify the boron passing through skin. Human volunteers were dosed with 10B-enriched boric acid, 5.0%, borax, 5.0%, or disodium octaborate tetrahydrate, 10%, in aqueous solutions. Urinalysis, for boron and changes in boron isotope ratios, was used to measure absorption. Boric acid in vivo percutaneous absorption was 0.226 (SD = 0.125) mean percentage dose, with flux and permeability constant (Kp) calculated at 0.009 microgram/cm2/h and 1.9 x 10(-7) cm/h, respectively. Borax absorption was 0.210 (SD = 0.194) mean percentage of dose, with flux and Kp calculated at 0.009 microgram/cm2/h and 1.8 x 10(-7) cm/h, respectively. DOT absorption was 0.122 (SD = 0.108) mean percentage, with flux and Kp calculated at 0.01 microgram/cm2/h and 1.0 x 10(-7) cm/h, respectively. Pretreatment with the potential skin irritant 2% sodium lauryl sulfate had no effect on boron skin absorption. In vitro human skin percentage of doses of boric acid absorbed were 1.2 for a 0.05% solution, 0.28 for a 0.5% solution, and 0.70 for a 5.0% solution. These absorption amounts translated into flux values of, respectively, 0.25, 0.58, and 14.58 micrograms/cm2/h and permeability constants (Kp) of 5.0 x 10(-4), 1.2 x 10(-4), and 2.9 x 10(-4) cm/h for the 0.05, 0.5, and 5.0% solutions. The above in vitro doses were at infinite, 1000 microliters/cm2 volume. At 2 microliters/cm2 (the in vivo dosing volume), flux decreased some 200-fold to 0.07 microgram/cm2/h and Kp of 1.4 x 10(-6) cm/h, while percentage of dose absorbed was 1.75%. Borax dosed at 5.0%/1000 microliters/cm2 had 0.41% dose absorbed, flux at 8.5 micrograms/cm2/h, and Kp was 1.7 x 10(-4) cm/h. Disodium octaborate tetrahydrate (DOT) dosed at 10%/1000 microliters/cm2 was 0.19% dose absorbed, flux at 7.9 micrograms/cm2/h, and Kp was 0.8 x 10(-4) cm/h. These in vitro results from infinite doses (1000 microliters/cm2) were 1000-fold greater than those obtained in the companion in vivo study. The results from the finite (2 microliters/cm2) dosing were closer (10-fold difference) to the in vivo results. General application of infinite dose percutaneous absorption values for risk assessment is questioned by these results. These in vivo results show that percutaneous absorption of boron, as boric acid, borax, and disodium octaborate tetrahydrate, through intact human skin, is low and is significantly less than the average daily dietary intake. This very low boron skin absorption makes it apparent that, for the borates tested, the use of gloves to prevent systemic uptake is unnecessary. These findings do not apply to abraded or otherwise damaged skin.

Phosphorous doped p-type MoS2 polycrystalline thin films via direct sulfurization of Mo film

NASA Astrophysics Data System (ADS)

Momose, Tomohiro; Nakamura, Atsushi; Daniel, Moraru; Shimomura, Masaru

2018-02-01

We report on the successful synthesis of a p-type, substitutional doping at S-site, MoS2 thin film using Phosphorous (P) as the dopant. MoS2 thin films were directly sulfurized for molybdenum films by chemical vapor deposition technique. Undoped MoS2 film showed n-type behavior and P doped samples showed p-type behavior by Hall-effect measurements in a van der Pauw (vdP) configuration of 10×10 mm2 area samples and showed ohmic behavior between the silver paste contacts. The donor and the acceptor concentration were detected to be ˜2.6×1015 cm-3 and ˜1.0×1019 cm-3, respectively. Hall-effect mobility was 61.7 cm2V-1s-1 for undoped and varied in the range of 15.5 ˜ 0.5 cm2V-1s-1 with P supply rate. However, the performance of field-effect transistors (FETs) declined by double Schottky barrier contacts where the region between Ni electrodes on the source/drain contact and the MoS2 back-gate cannot be depleted and behaves as a 3D material when used in transistor geometry, resulting in poor on/off ratio. Nevertheless, the FETs exhibit hole transport and the field-effect mobility showed values as high as the Hall-effect mobility, 76 cm2V-1s-1 in undoped MoS2 with p-type behavior and 43 cm2V-1s-1 for MoS2:P. Our findings provide important insights into the doping constraints for transition metal dichalcogenides.

Energy-storage properties and electrocaloric effect of Pb(1-3x/2)LaxZr0.85Ti0.15O3 antiferroelectric thick films.

PubMed

Zhao, Ye; Hao, Xihong; Zhang, Qi

2014-07-23

Antiferroelectric (AFE) thick (1 μm) films of Pb(1-3x/2)LaxZr0.85Ti0.15O3 (PLZT) with x = 0.08, 0.10, 0.12, and 0.14 were deposited on LaNiO3/Si (100) substrates by a sol-gel method. The dielectric properties, energy-storage performance, electrocaloric effect, and leakage current behavior were investigated in detail. With increasing La content, dielectric constant and saturated polarizations of the thick films were gradually decreased. A maximum recoverable energy-storage density of 38 J/cm(3) and efficiency of 71% were achieved in the thick films with x = 0.12 at room temperature. A large reversible adiabatic temperature change of ΔT = 25.0 °C was presented in the thick films with x = 0.08 at 127 °C at 990 kV/cm. Moreover, all the samples had a lower leakage current density below 10(-6) A/cm(2) at room temperature. These results indicated that the PLZT AFE thick films could be a potential candidate for applications in high energy-storage density capacitors and cooling devices.

[Physical growth trend of Chinese children under 7 years old, in 1975 - 2005].

PubMed

Li, Hui; Zhang, Ya-qin; Zhu, Zong-han

2009-03-01

To analyze the physical growth changes in Chinese children aged from 0 to 7 years old during the past 30 years. Four national physical growth surveys of the children under 7 years old were undertaken in the same urban and suburban areas of nine main cities in China from 1975 to 2005. The nine cities were Beijing, Harbin and Xi'an in the northern part; Shanghai, Nanjing and Wuhan in the central part; Guangzhou, Fuzhou and Kunming in the southern part of China. Random cluster sampling method was used. The children aged from 0 to 7 years old were classified into 22 groups by age. The sample size was ranged from 150 to 200 persons for each sex-age group in each area (urban/rural) of each city. Totally, 158 400, 152 874, 157 362 and 138 775 healthy children were examined in 1975, 1985, 1995 and 2005 respectively. The data of weight, height, chest and head circumference obtained from these surveys were analyzed. Average weight and height in most of the age groups for both boys and girls from urban and suburban rural areas has been significantly improved during the past 30 years, the average increments of weight were 0.76 kg to 1.14 kg in 12 - 15 months group and 2.58 kg to 3.26 kg in 6 - 7 years group; and the average increments of height were 2.7 cm to 3.8 cm in 12 - 15 months group and 5.0 cm to 7.6 cm in 6 - 7 years group. Chest circumference did not show an increase in infants younger than 4 months and increased slightly after 4 months. The average increments of head circumference were 0.1 cm to 1.0 cm. From 1975 to 2005, the increments of weight and height per 10 years was in an increasing trend, e.g. weight increments of 5 - 6 years old were 0.58 kg, 1.02 kg and 1.67 kg and the height increments were 1.5 cm, 2.0 cm and 2.6 cm for every 10 years. The urban-rural difference in height has become smaller, the height difference in 6 - 7 years group for boys was decreased from 4.9 cm in 1975 to 2.6 cm in 2005. The weight has become smaller in children under 3 years old but becoming greater after 3 years, such as the difference increased from 1.14 kg in 1975 to 1.72 kg in 2005 for boys aged 6 - 7 years old. The regional difference also showed a decreasing trend. The physical growth of Chinese children had been much improved during the past 30 years and the secular trend should be still continuing at an accelerated growth stage. The urban-rural difference and regional difference in weight and height had become smaller.

Studies on Synthesis, Microstructure and Transport Properties of Doped Cerium Oxides

NASA Astrophysics Data System (ADS)

Handal, Hala Talaat Abd El-Samei

Acceptor-doped ceria exhibits mixed ionic electronic conduction in reducing conditions and chemical stability against sulfur poisoning and coking. This thesis's primary goal is to explore new anode materials based on ceria--solid solutions for solid oxide fuel cells (SOFCs). The physicochemical and electrochemical performance of Ce0.9-xY 0.1MnxO2-delta ( x = 0 to 15 mol%) (CYMO) and Ce0.87Y0.1Mn 0.01N0.02O2-delta (N = Mg or Ca) were studied. Among the materials investigated in this study, Ce0.89Y 0.1Mn0.01Mg0.02O2-delta (Mg-CYMO) showed the highest total conductivity of 0.2 S cm-1 at 700°C in H2. An area specific polarization resistance of 0.23 O cm2 was observed for both Mg-CYMO and Ce0.8Y 0.1Mn0.1O2-delta (10CYMO) at 800°C, in wet H2. Chronoamperometric measurement for the symmetrical cell configuration based on 10CYMO electrodes showed stable performance upon exposure to 10 ppm H2S/H2. In a full cell configuration, 10CYMO (anode)/YSZ (electrolyte)/La0.8Sr0.2MnO3 (LSM)-YSZ cathode, polarization resistance of 1.4 O cm2 and power density of 75 mW/cm2 were obtained at 800°C in wet H2. The main challenge of employing proton-conducting electrolytes in SOFC is their poor chemical stability in the presence of steam and hydrocarbon fuels. Another goal of this thesis is to develop a chemically stable proton-conducting electrolyte for SOFCs. The effects of Fe and Co substitution on the electrical and physicochemical properties of BaCe0.9Sm0.1O 3-delta (BCS) were evaluated. Thermogravimetric analysis showed that incorporation of 5 to 10 mol% Fe or Co in BCS did not improve the chemical stability in CO2 at elevated temperatures. The BCSC10 sample sintering at 1400°C showed the highest electrical conductivity of 0.02 S cm -1 at 600°C in air, but it did not show any appreciable proton mobility under humidified atmosphere.

The effectiveness of surface liming in ameliorating the phytotoxic effects of soil contaminated by copper acid leach pad solution in an arid ecosystem

NASA Astrophysics Data System (ADS)

Golos, Peter

2016-04-01

Revegetation of sites following soil contamination can be challenging especially in identifying the most effective method for ameliorating phytotoxic effects in arid ecosystems. This study at a copper mine in the Great Sandy Desert of Western Australia investigated vegetation restoration of a site contaminated by acid (H2SO4) leach pad solution. Elevated soil copper at low soil pH is phytotoxic to plant roots inhibiting root elongation. In arid ecosystems where rapid root growth is crucial for seedling survival post germination physical or chemical barriers to root growth need to be identified and ameliorated. Initial attempt at rehabilitation of contaminated site with hydrated lime (CaOH2) at 2 tonnes/ha followed by ripping to 30 cm depth then seeding was ineffective as successful seedling emergence was followed by over 90% seedling mortality which was 10-fold greater than seedling mortality in an uncontaminated reference site. High mortality was attributed to seedling roots being impededed as soil water was more than 3-fold greater at 5 to 40 cm depth in contaminated site than reference site. In response to high seedling mortality after emergence test pits were dug to 1 m deep to collect soil samples at 10 cm intervals for phytotoxicity testing and to measure soil pH-CaCl2, copper (DPTA ion extraction), electrical conductivity and gravimetric water content in three replicate pits at three replicate sites. Also, soil impedance was measured down the soil profile at 5 cm intervals at six replicate points/pit. For phytotoxicity testing soil samples were placed into three replicate plastic pots/sample and seeded with 10 seeds of Avena sativa and watered daily. Seedlings were harvested after at least two weeks after seedling emergence and rooting depth in pots measured. There was no difference in seedling emergence and survival of seedlings between contaminated and uncontaminated soil samples however mean seedling root growth was significantly lower in soil samples collected at >10 cm depth than the control. Mean soil pH at 0-10 cm was higher (>7.2) at all sites treated with lime compared to uncontaminated soil (5.5). At depths greater than 10 cm soil pH was <4.6. Soil copper was >16 mg/kg in all contaminated soil samples compared to 0.5 mg/kg in control. High seedling mortality in contaminated site is attributed to low soil pH and elevated soil copper levels which inhibited plant root growth and hence access to soil water. While surface liming of soil increased soil pH ameliorating the effect of elevated soil copper, this was only effective in the top 10 cm due to low solubility of hydrated lime. To improve seedling survival lime will need to be incorporated into the contaminated soil profile to allow plants to access soil water at depth. This study highlights the importance of the need to assess the phytotoxic effects of soil contamination and the effectiveness of amelioration treatments and with proper reference to its ecological context. To improve the success of vegetation restoration of sites contaminated with acidic copper solution, lime needs to be incorporated into the contaminated soil profile to allow plant roots to access soil water at depth. This study highlights the importance of the need to assess the phytotoxic effects of soil contamination and the effectiveness of amelioration treatments and with proper reference to its ecological context.

Ex vivo evaluation of canine lung biopsy techniques.

PubMed

Marvel, Sarah; Monnet, Eric

2013-05-01

An ex vivo comparison of thoracoscopic lung biopsy techniques in dogs. Experimental. Cadaveric canine lung lobes. Lungs were inflated to 10 cmH2 O. After collecting biopsies 3 cm from the edge of lung lobes, leak pressures were recorded as inflation pressure was increased to 40 cmH2 O. Pre-tied loop ligature, square knot (SQ), modified 4S Roeder knot (M4SR) with glycomer 631 and polyglactin 910 size 0 and 2-0 were used in addition to EndoGIA 45-2.5 mm (Covidien, Norwalk, CT) and a vessel sealant device (VSDS single and VSDD double seal). Six biopsies were performed with each of these modalities. Median airway pressure at which leakage occurred was 28 (20-34)cmH2 O for EndoGIA 45; 33 (14-40) for VSDD; and 33 (10-40) for VSDS while other groups reached a median pressure of 40 cmH2 O (P < .0001). Leakage occurred at 20 cmH2 O in 1 sample with the EndoGIA and the VSDS, and in 2 with the VSDD while leakage did not occur in any other group (P = .36). Leakage occurred at 30 cmH2 O in 1 specimen each of the 0-polyglactin SQ, 2-0 glycomer 631 M4SR, 2-0 polyglactin M4SR, and 2-0 Surgitie (Covidien, Norwalk, CT); 2 with the VSDS; and 3 with the EndoGIA and the VSDD while leakage did not occur in any other group (P = .26). All tested techniques seemed safe except the vessel sealant device since it did not consistently seal every biopsy and leaked at pressures <20 cmH2 O. © Copyright 2013 by The American College of Veterinary Surgeons.

Soil organic carbon and nitrogen accumulation on coal mine spoils reclaimed with maritime pine (Pinus pinaster Aiton) in Agacli-Istanbul.

PubMed

Sever, Hakan; Makineci, Ender

2009-08-01

Mining operations on open coal mines in Agacli-Istanbul have resulted in the destruction of vast amounts of land. To rehabilitate these degraded lands, plantations on this area began in 1988. Twelve tree species were planted, however, the most planted tree species was maritime pine (Pinus pinaster Aiton). This study performed on 14 sample plots randomly selected in maritime pine plantations on coal mine soil/spoils in 2005. Soil samples were taken from eight different soil layers (0-1, 1-3, 3-5, 5-10, 10-20, 20-30, 30-40 and 40-50 cm) into the soil profile. On soil samples; fine soil fraction (<2 mm), soil acidity (pH), organic carbon (C(org)) and total nitrogen (N(t)) contents were investigated, and results were compared statistically among soil layers. As a result, 17 years after plantations, total forest floor accumulation determined as 17,973.20 kg ha(-1). Total nitrogen and organic matter amounts of forest floor were 113.90 and 14,640.92 kg ha(-1) respectively. Among soil layers, the highest levels of organic carbon (1.77%) and total nitrogen (0.096%) and the lowest pH value (pH 5.38) were found in 0-1 cm soil layer, and the variation differs significantly among soil layers. Both organic carbon and total nitrogen content decreased, pH values increased from 0-1 to 5-10 cm layer. In conclusion, according to results obtained maritime pine plantations on coal mine spoils; slow accumulation and decomposition of forest floor undergo simultaneously. Depending on these changes organic carbon and total nitrogen contents increased in upper layer of soil/spoil.

Effect of starter culture and turmeric on physico-chemical quality of carabeef pastirma.

PubMed

Maurya, P; Borpuzari, R N; Nath, D R; Nath, N C

2010-01-01

Carabeef samples were sliced, pressed, cured and divided into 6 groups. Starter cultures (Micrococcus varians M483 (MV), Staphylococcus carnosus (SC), Lactobacillus sakei (LS), M. varians M483+ Lb. sakei and Staph. carnosus + Lb. sakei) were inoculated at the dose of 10(6)-0(7)cfu/g and stored at 10 ± 1°C for 7 days. Uninoculated samples were maintained as control. Samples were then divided into 2 treatment groups. Samples of treatment 1 (T1) were smeared with a paste of turmeric followed by application of a thick layer of the paste of garlic, cumin, black pepper and red pepper whereas, samples of treatment 2 (T2) were applied with a thick layer of spices as above without turmeric. With the gradual fall in pH there was a reduction in water-holding capacity (WHC) of samples. The WHC of samples treated with SC+LS of T1 reduced to 6.3 ± 0.03 cm(2) and those inoculated with MV+LS of T2 to 6.2 ± 0.03 cm(2). The extract release volume (ERV) increased in all samples during storage. The least ERV of 11.7 and 11.6 ml were recorded in samples inoculated with MV of T1 and T2, respectively. The tyrosine (TV) and thiobarbituric acid (TBA) number of turmeric treated samples were significantly lower than non turmeric treated samples. The samples inoculated with LS had the least TV of 30.9 mg tyrosine/100 g of meat and TBA number of 0.06 mg manoladehyde/kg of meat. Samples inoculated with MV and LS of both T1 and T2 were better in physico-chemical qualities.

Creation of 0.10-cm-1 resolution quantitative infrared spectral libraries for gas samples

NASA Astrophysics Data System (ADS)

Sharpe, Steven W.; Sams, Robert L.; Johnson, Timothy J.; Chu, Pamela M.; Rhoderick, George C.; Guenther, Franklin R.

2002-02-01

The National Institute of Standards and Technology (NIST) and the Pacific Northwest National Laboratory (PNNL) are independently creating quantitative, approximately 0.10 cm-1 resolution, infrared spectral libraries of vapor phase compounds. The NIST library will consist of approximately 100 vapor phase spectra of volatile hazardous air pollutants (HAPs) and suspected greenhouse gases. The PNNL library will consist of approximately 400 vapor phase spectra associated with DOE's remediation mission. A critical part of creating and validating any quantitative work involves independent verification based on inter-laboratory comparisons. The two laboratories use significantly different sample preparation and handling techniques. NIST uses gravimetric dilution and a continuous flowing sample while PNNL uses partial pressure dilution and a static sample. Agreement is generally found to be within the statistical uncertainties of the Beer's law fit and less than 3 percent of the total integrated band areas for the 4 chemicals used in this comparison. There does appear to be a small systematic difference between the PNNL and NIST data, however. Possible sources of the systematic difference will be discussed as well as technical details concerning the sample preparation and the procedures for overcoming instrumental artifacts.

RBS, SY-XRF, INAA and ICP-IDMS of antimony implanted in silicon - A multi-method approach to characterize and certify a reference material

NASA Astrophysics Data System (ADS)

Ecker, K. H.; Wätjen, U.; Berger, A.; Persson, L.; Pritzkow, W.; Radtke, M.; Riesemeier, H.

2002-04-01

A layer of Sb atoms, implanted with an energy of 400 keV and a nominal dose of 5×10 16 atoms/cm 2 into a high purity silicon wafer, was certified for its areal density (atoms/cm 2) using Rutherford backscattering spectrometry (RBS), instrumental neutron activation analysis (INAA) and inductively coupled plasma isotope dilution mass spectrometry (ICP-IDMS) and for its isotope ratio using INAA and ICP-IDMS. Excellent agreement between the results of the different independent methods was found. In the present work, the measurements of the homogeneity of the areal density of Sb, previously determined with RBS in spots having 1 mm diameter, are improved with synchrotron X-ray fluorescence analysis: Higher precision in even smaller sample spots allows to estimate a reduced inhomogeneity of the whole batch of samples of the order of only 0.4%. Thus the uncertainty of the certified value can further be reduced. Down to fractions of a chip with 0.3×0.4 mm 2 area, the areal density is now certified as (4.81±0.06)×10 16 Sb atoms/cm 2, where the expanded uncertainty 0.06 (coverage factor k=2) corresponds to only 1.2%. The relative merits of the different analytical methods are discussed.

Electrical conductivity measurement of excised human metastatic liver tumours before and after thermal ablation.

PubMed

Haemmerich, Dieter; Schutt, David J; Wright, Andrew W; Webster, John G; Mahvi, David M

2009-05-01

We measured the ex vivo electrical conductivity of eight human metastatic liver tumours and six normal liver tissue samples from six patients using the four electrode method over the frequency range 10 Hz to 1 MHz. In addition, in a single patient we measured the electrical conductivity before and after the thermal ablation of normal and tumour tissue. The average conductivity of tumour tissue was significantly higher than normal tissue over the entire frequency range (from 4.11 versus 0.75 mS cm(-1) at 10 Hz, to 5.33 versus 2.88 mS cm(-1) at 1 MHz). We found no significant correlation between tumour size and measured electrical conductivity. While before ablation tumour tissue had considerably higher conductivity than normal tissue, the two had similar conductivity throughout the frequency range after ablation. Tumour tissue conductivity changed by +25% and -7% at 10 Hz and 1 MHz after ablation (0.23-0.29 at 10 Hz, and 0.43-0.40 at 1 MHz), while normal tissue conductivity increased by +270% and +10% at 10 Hz and 1 MHz (0.09-0.32 at 10 Hz and 0.37-0.41 at 1 MHz). These data can potentially be used to differentiate tumour from normal tissue diagnostically.

THE HIGH-RESOLUTION INFRARED SPECTRUM OF O$sup 18$-ENRICHED CO$sub 2$

DOE Office of Scientific and Technical Information (OSTI.GOV)

Berney, C.V.

1962-01-01

The infrared spectrum of a sample of CO/sub 2/ enriched to about 10 at.% with O/sup 18/ was examined in the region of 5400 to 1620 cm/sup -1/, using an Ebert grating spectrometer with spectral slit widths ranging from 0.4 to 0.2 cm/ sup -1/. Various bands of O/sup 18/-substituted species of CO/sub 2/ were observed, including several which were not previously reported under comparable resolution. These are given, together with the observed band centers in cm/sup - 1/. The data are compared with values calculated from vibrational constants given by Courtoy (Ann. Soc. Sci. Bruxelles 73: No. I, 1959).more » Band centers for the unsymmetrical species were found to be consistently higher than calculated, by 0.2 to 1.3 cm/sup -1/. The anomalously large Fermi resonance constant (52.5 cm/sup -1/) found by Courtoy for C/sup 12/O/sup 16/O/sup 18/ was confirmed, an d the C/sup 12/O/sup 18/ bands observed indicated that it is even higher (around 53.7 cm/sup -1/) for the doubly-substituted species. Rotational data for C/sup 12/O/sup 16/O/sup 18/ indicated that alpha /sup 3/ is abo ut 287 x 10/sup -5/ cm/ sup -1/, slightly smaller than the value suggested by Courtoy. (Dissertation Abstr.)« less

Influence of soil moisture on soil respiration

NASA Astrophysics Data System (ADS)

Fer, Miroslav; Kodesova, Radka; Nikodem, Antonin; Klement, Ales; Jelenova, Klara

2015-04-01

The aim of this work was to describe an impact of soil moisture on soil respiration. Study was performed on soil samples from morphologically diverse study site in loess region of Southern Moravia, Czech Republic. The original soil type is Haplic Chernozem, which was due to erosion changed into Regosol (steep parts) and Colluvial soil (base slope and the tributary valley). Soil samples were collected from topsoils at 5 points of the selected elevation transect and also from the parent material (loess). Grab soil samples, undisturbed soil samples (small - 100 cm3, and large - 713 cm3) and undisturbed soil blocks were taken. Basic soil properties were determined on grab soil samples. Small undisturbed soil samples were used to determine the soil water retention curves and the hydraulic conductivity functions using the multiple outflow tests in Tempe cells and a numerical inversion with HYDRUS 1-D. During experiments performed in greenhouse dry large undisturbed soil samples were wetted from below using a kaolin tank and cumulative water inflow due to capillary rise was measured. Simultaneously net CO2 exchange rate and net H2O exchange rate were measured using LCi-SD portable photosynthesis system with Soil Respiration Chamber. Numerical inversion of the measured cumulative capillary rise data using the HYDRUS-1D program was applied to modify selected soil hydraulic parameters for particular conditions and to simulate actual soil water distribution within each soil column in selected times. Undisturbed soil blocks were used to prepare thin soil sections to study soil-pore structure. Results for all soil samples showed that at the beginning of soil samples wetting the CO2 emission increased because of improving condition for microbes' activity. The maximum values were reached for soil column average soil water content between 0.10 and 0.15 cm3/cm3. Next CO2 emission decreased since the pore system starts filling by water (i.e. aggravated conditions for microbes, closing soil gas pathways etc.). In the case of H2O exchange rate, values increased with increasing soil water contents (up to 0.15-0.20 cm3/cm3) and then remained approximately constant. Acknowledgement: Authors acknowledge the financial support of the Ministry of Agriculture of the Czech Republic No. QJ1230319

TLC-spectrophometric separation and trace determination of monocrotophos and dichlorvos in enviromental and biological samples.

PubMed

Janghel, Etesh K; Rai, J K; Khan, S; Rai, M K; Gupta, V K

2007-04-01

Organophosphorus insecticides, monocrotophos and dichlrovos are increasingly being used in agriculture to control insects on a wide range of crops. Their ready access has resulted in misuse in many instances of homicidal and suicidal poisoning cases. This paper describes about a chromogenic spray reagent for the detection/determination of monocrophos and dichlrovos in environmental and biological samples by TLC and spectrophotometric method. Monocrotophos and dichlorvos on alkaline hydrolysis yield N-methyl acetoacetamide and dichlroacetaldehyde respectively, which in turn react with diazotized p-amino acetophenone to give red-violet and red coloured compounds. Other organophosphorus insecticides do not give this reaction. Moreover, organochlorine and synthetic pyrethroid insecticides and constituents of viscera (amino acids, peptides, proteins etc), which are generally coextracted with the insecticides, do not interfere. However, phenolic compounds and hydrolysed product of carbamate insecticides may interfere and differentiate from monocrotophos and dichlrovos by Rf values. The lower limit of detection is 0.2 mg for monocrotophos and 0.1 mg for dichlorovos. The absorption maxima of the reddish-violet and red colour formed by monocrotophos and dichlrovos, are measured at 560 nm and 540 nm respectively. Beer's Law is obeyed over the concentration range of 1.2 to 6.8 mg and 6.2 to 35 mg in the final solution volume of 25 mL. The molar absorptivity and Sandell's sensitivity of monocrotophos and dichlrovos were found to be 7.1 x 10(5) (+100) 1 mole(-1) cm(-1) and 0.008 mg cm(-2), 1.2 x 10(5) 1 mole(-1) cm(-1) and 0.003 mg cm(-2) respectively. The standard deviation and relative standard deviation were found be +/- 0.005 and 2.05% +/- 0.007 and 2.02% respectively. The developed method has been successfully applied to the detection and determination of monocrotophos and dichlrovos in environmental and biological samples.

Photolysis and oxidation of azidophenyl-substituted radicals: delocalization in heteroatom-based radicals.

PubMed

Serwinski, Paul R; Esat, Burak; Lahti, Paul M; Liao, Yi; Walton, Richard; Lan, Jiang

2004-08-06

2-(4-Azidophenyl)-4,4,5,5-tetramethyl-4,5-dihydro-1H-imidazole-3-oxide-1-oxyl (14), 2-(4-azidophenyl)benzimidazole-1-oxide-3-oxyl (16), 2-(4-azidophenyl)-1,2,6-triphenylverdazyl (19), 2-(3-azidophenyl)-4,4,5,5-tetramethyl-4,5-dihydro-1H-imidazole-3-oxide-1-oxyl (21), and (3-azidophenyl)-N-tert-butyl-N-aminoxyl (25) were photolyzed in frozen solution to give S = 3/2 state ESR spectra of the corresponding nitrenophenyl radicals with the following zero-field splitting parameters: |D/hc| = 0.277 cm(-1), |E/hc| < or = 0.002 cm(-1) (7 from 14); |D/hc| = 0.256 cm(-1), |E/hc| < or = 0.002 cm(-1) (8 from 16); |D/hc| = 0.288 cm(-1), |E/hc| < or = 0.002 cm(-1) (9 from 19); |D/hc| = 0.352 cm(-1), |E/hc| = 0.006 cm(-1) (10 from 21); |D/hc| = 0.336 cm(-1), |E/hc| = 0.004 cm(-1) (11 from 25). UB3LYP/6-31G computations and ESR spectroscopic analyses suggest that these are nitreno radicals, even para-linked systems with possible quinonoidal resonance forms. Neat samples of azidophenyl radicals 14 and 21 showed bulk paramagnetic behavior, consistent with the lack of close contacts in their crystal structures. Efforts to make photolabile coordination complexes of 14 and 21 with paramagnetic transition metal ions were unsuccessful: Cu(ClO4)2 x 6H2O instead oxidized them to the corresponding diamagnetic nitrosonium perchlorate salts. Copyright 2004 American Chemical Society

Raman study of the Hg0.7Cr0.3Sr2CuO4+δ superconductors

NASA Astrophysics Data System (ADS)

Lee, S.-Y.; Chang, B.-Y.; Yang, I.-S.; Gwak, J.-H.; Kim, S.-J.; Choi, J.-H.; Lee, S.-I.; Yakhmi, J. V.; Mandal, J. B.; Bandyopadhyay, B.; Ghosh, B.

1997-08-01

The local environment of the apical oxygens (OA) in the Sr-substituted mercury-based superconductor Hg0.7Cr0.3Sr2CuO4+δ is investigated using Raman spectroscopy. Raman spectra from the Sr-substituted Hg-1201 samples show broad OA A1g double peaks at 553 and 583 cm-l, which are 10 - 20 cm-1 lower than the pristine Hg-1201. The existence of, and lower shift of, the double peaks in the Raman spectra of the Sr-substituted Hg-1201 superconductors indicate changes in the environment of OA in the Sr-substituted mercury-based superconductors.

Structural, electrical, magnetic and magnetoelectric properties of composites

NASA Astrophysics Data System (ADS)

Rani, Renu; Juneja, J. K.; Singh, Sangeeta; Prakash, Chandra; Raina, K. K.

2013-11-01

The magnetoelectric (ME) composites with composition (y)Ni0.8Zn0.2Fe2O4+(1-y) Ba0.90Sr0.10Zr0.04Ti0.96O3 ((y)NZF+(1-y)BSZT) (where y=0.00-0.15 in wt%) were prepared by the conventional solid state reaction route. The existence of both phases was confirmed by the X-Ray diffraction technique and the lattice parameters for all samples were calculated. The dielectric properties such as dielectric constant and dielectric loss were measured as a function of temperature at different frequencies. P-E hysteresis loops and M-H hysteresis loops confirm the ferroelectric and ferrimagnetic nature of the composite samples. M-H loops for electrically poled and un-poled samples were compared to prove ME evidences. Variation of ME coefficient (α) with dc magnetic field was also studied for all composite samples. The maximum value of α (1.6 mV/cm Oe) was observed for y=0.10 at 750 Oe.

Phthalic acid esters in soils from vegetable greenhouses in Shandong Peninsula, East China.

PubMed

Chai, Chao; Cheng, Hongzhen; Ge, Wei; Ma, Dong; Shi, Yanxi

2014-01-01

Soils at depths of 0 cm to 10 cm, 10 cm to 20 cm, and 20 cm to 40 cm from 37 vegetable greenhouses in Shandong Peninsula, East China, were collected, and 16 phthalic acid esters (PAEs) were detected using gas chromatography-mass spectrometry (GC-MS). All 16 PAEs could be detected in soils from vegetable greenhouses. The total of 16 PAEs (Σ16PAEs) ranged from 1.939 mg/kg to 35.442 mg/kg, with an average of 6.748 mg/kg. Among four areas, including Qingdao, Weihai, Weifang, and Yantai, the average and maximum concentrations of Σ16PAEs in soils at depths of 0 cm to 10 cm appeared in Weifang, which has a long history of vegetable production and is famous for extensive greenhouse cultivation. Despite the different concentrations of Σ16PAEs, the PAE compositions were comparable. Among the 16 PAEs, di(2-ethylhexyl) phthalate (DEHP), di-n-octyl phthalate (DnOP), di-n-butyl phthalate (DnBP), and diisobutyl phthalate (DiBP) were the most abundant. Compared with the results on agricultural soils in China, soils that are being used or were used for vegetable greenhouses had higher PAE concentrations. Among PAEs, dimethyl phthalate (DMP), diethyl phthalate (DEP) and DnBP exceeded soil allowable concentrations (in US) in more than 90% of the samples, and DnOP in more than 20%. Shandong Peninsula has the highest PAE contents, which suggests that this area is severely contaminated by PAEs.

Phthalic Acid Esters in Soils from Vegetable Greenhouses in Shandong Peninsula, East China

PubMed Central

Chai, Chao; Cheng, Hongzhen; Ge, Wei; Ma, Dong; Shi, Yanxi

2014-01-01

Soils at depths of 0 cm to 10 cm, 10 cm to 20 cm, and 20 cm to 40 cm from 37 vegetable greenhouses in Shandong Peninsula, East China, were collected, and 16 phthalic acid esters (PAEs) were detected using gas chromatography-mass spectrometry (GC-MS). All 16 PAEs could be detected in soils from vegetable greenhouses. The total of 16 PAEs (Σ16PAEs) ranged from 1.939 mg/kg to 35.442 mg/kg, with an average of 6.748 mg/kg. Among four areas, including Qingdao, Weihai, Weifang, and Yantai, the average and maximum concentrations of Σ16PAEs in soils at depths of 0 cm to 10 cm appeared in Weifang, which has a long history of vegetable production and is famous for extensive greenhouse cultivation. Despite the different concentrations of Σ16PAEs, the PAE compositions were comparable. Among the 16 PAEs, di(2-ethylhexyl) phthalate (DEHP), di-n-octyl phthalate (DnOP), di-n-butyl phthalate (DnBP), and diisobutyl phthalate (DiBP) were the most abundant. Compared with the results on agricultural soils in China, soils that are being used or were used for vegetable greenhouses had higher PAE concentrations. Among PAEs, dimethyl phthalate (DMP), diethyl phthalate (DEP) and DnBP exceeded soil allowable concentrations (in US) in more than 90% of the samples, and DnOP in more than 20%. Shandong Peninsula has the highest PAE contents, which suggests that this area is severely contaminated by PAEs. PMID:24747982

Visual detection of particulates in processed meat products by x ray

NASA Astrophysics Data System (ADS)

Schatzki, Thomas F.; Young, Richard; Haff, Ron P.; Eye, J.; Wright, G.

1995-01-01

A test has been run to study the efficacy of detecting particulate contaminants in processed meat samples by manual observation of line-scanned x-ray images. Six hundred processed product samples arriving over a 3 month period at a national USDA-FSIS laboratory were scanned at 230 cm2sec with 0.5 X 0.5 mm resolution, using 50 KV, 13 ma excitation, with digital interfacing and image correction. Images were inspected off-line, using interactive image enhancement. Forty percent of the samples were spiked, blind to the analyst, in order to establish the manual recognition rate as a function of sample thickness [1 - 10 cm] and texture of the x-ray image [smooth/textured], as well as spike composition [wood/bone/glass], size [1 - 4 mm] and shape [splinter/round]. The results have been analyzed using maximum likelihood logistic regression. In meat packages less than 6 cm thick, 2 mm bone chips are easily recognized, 1 mm glass splinters with some difficulty, while wood is generally missed even at 4 mm. Operational feasibility in a time-constrained setting has bee confirmed. One half percent of the samples arriving from the field contained bone slivers > 1 cm long, one half percent contained metallic material, while 4% contained particulates exceeding 3.2 mm in size. All of the latter appeared to be bone fragments.

Microfabricated capillary electrophoresis amino acid chirality analyzer for extraterrestrial exploration

NASA Technical Reports Server (NTRS)

Hutt, L. D.; Glavin, D. P.; Bada, J. L.; Mathies, R. A.

1999-01-01

Chiral separations of fluorescein isothiocyanate-labeled amino acids have been performed on a microfabricated capillary electrophoresis chip to explore the feasibility of using such devices to analyze for extinct or extant life signs in extraterrestrial environments. The test system consists of a folded electrophoresis channel (19.0 cm long x 150 microns wide x 20 microns deep) that was photolithographically fabricated in a 10-cm-diameter glass wafer sandwich, coupled to a laser-excited confocal fluorescence detection apparatus providing subattomole sensitivity. Using a sodium dodecyl sulfate/gamma-cyclodextrin pH 10.0 carbonate electrophoresis buffer and a separation voltage of 550 V/cm at 10 degrees C, baseline resolution was observed for Val, Ala, Glu, and Asp enantiomers and Gly in only 4 min. Enantiomeric ratios were determined for amino acids extracted from the Murchison meteorite, and these values closely matched values determined by HPLC. These results demonstrate the feasibility of using microfabricated lab-on-a-chip systems to analyze extraterrestrial samples for amino acids.

Creation of short microwave ablation zones: In Vivo Characterization of single and paired Modified Triaxial Antennas Laboratory Investigation

PubMed Central

Lubner, Meghan G.; Ziemlewicz, Tim J; Hinshaw, J. Louis; Lee, Fred T.; Sampson, Lisa J.; Brace, Chris L.

2014-01-01

Purpose To characterize modified triaxial microwave antennas configured to produce short ablation zones. Materials and Methods 50 single- and 27 paired-antenna hepatic ablations were performed in domestic swine (n=11) with 17-gauge, gas-cooled modified triaxial antennas powered at 65W from a 2.45 GHz generator. Single-antenna ablations were performed at 2 (n=16), 5 (n=21), and 10 (n=13) minutes. Paired-antenna ablations were performed at 1-cm and 2-cm spacing for 5 (n=7, n=8) and 10 minutes (n=7, n=5). Mean transverse width, length and aspect ratio of sectioned ablation zones were measured and compared. Results For single antennas, mean ablation zone length was 2.9±0.45, 3.5±0.55 and 4.2±0.40 cm at 2, 5, and 10 minutes respectively. Mean width was 1.8±0.3, 2.0±0.32, 2.5±0.25 cm at 2, 5, and 10 minutes. For paired antennas, mean length at 5 min 1 and 2 cm and 10 min 1 and 2 cm spacing was 4.2±0.9, 4.4±0.9, 4.8±0.5 and 4.3±0.9 cm respectively. Mean width was 3.1±1.0, 4.0±0.8 and 3.8±0.4, 4.2±0.6 cm respectively. Paired-antenna ablations were more spherical (aspect ratios 0.72-0.79 for 5-10 min) than single-antenna ablations (0.57-0.59). For paired-antenna ablations, 1 cm spacing appeared optimal, with improved circularity and decreased clefting compared to 2 cm spacing (circ 1 cm 0.85, 2 cm 0.78). Conclusion Modified triaxial antennas can generate relatively short, spherical ablation zones. Paired-antenna ablations were rounder and larger in transverse dimension compared to single antenna ablations, with 1 cm spacing optimal for confluence of the ablation zone. PMID:25156644

Real-Time Non-Intrusive Assessment of Viewing Distance during Computer Use.

PubMed

Argilés, Marc; Cardona, Genís; Pérez-Cabré, Elisabet; Pérez-Magrané, Ramon; Morcego, Bernardo; Gispets, Joan

2016-12-01

To develop and test the sensitivity of an ultrasound-based sensor to assess the viewing distance of visual display terminals operators in real-time conditions. A modified ultrasound sensor was attached to a computer display to assess viewing distance in real time. Sensor functionality was tested on a sample of 20 healthy participants while they conducted four 10-minute randomly presented typical computer tasks (a match-three puzzle game, a video documentary, a task requiring participants to complete a series of sentences, and a predefined internet search). The ultrasound sensor offered good measurement repeatability. Game, text completion, and web search tasks were conducted at shorter viewing distances (54.4 cm [95% CI 51.3-57.5 cm], 54.5 cm [95% CI 51.1-58.0 cm], and 54.5 cm [95% CI 51.4-57.7 cm], respectively) than the video task (62.3 cm [95% CI 58.9-65.7 cm]). Statistically significant differences were found between the video task and the other three tasks (all p < 0.05). Range of viewing distances (from 22 to 27 cm) was similar for all tasks (F = 0.996; p = 0.413). Real-time assessment of the viewing distance of computer users with a non-intrusive ultrasonic device disclosed a task-dependent pattern.

Lactate Injection by Electric Currents for Bioremediation of Tetrachloroethylene in Clay

PubMed Central

Wu, Xingzhi; Gent, David B.; Davis, Jeffrey L.; Alshawabkeh, Akram N.

2012-01-01

Biological transformation of tetrachloroethylene (PCE) in silty clay samples by ionic injection of lactate under electric fields is evaluated. To prepare contaminated samples, a silty clay slurry was mixed with PCE, inoculated with KB-1® dechlorinators and was consolidated in a 40 cm long cell. A current density between 5.3 and 13.3 A m−2 was applied across treated soil samples while circulating electrolytes containing 10 mg L−1 lactate concentration between the anode and cathode compartments to maintain neutral pH and chemically reducing boundary conditions. The total adsorbed and aqueous PCE was degraded in the soil to trichloroethylene (TCE), cis-1,2-dichloroethene (cis-DCE), vinyl chloride (VC) and ethene in 120 d, which is about double the time expected for transformation. Lactate was delivered into the soil by a reactive transport rate of 3.7 cm2 d−1 V−1. PCE degradation in the clay samples followed zero order transformation rates ranging from 1.5 to 5 mg L−1 d−1 without any significant formation of TCE. cis-DCE transformation followed first order transformation rates of 0.06 to 0.10 per day. A control experiment conducted with KB-1 and lactate, but without electricity did not show any significant lactate buildup or cis-DCE transformation because the soil was practically impermeable (hydraulic conductivity of 2×10−7 cm s−1). It is concluded that ionic migration will deliver organic additives and induce biological activity and complete PCE transformation in clay, even though the transformation occurs under slower rates compared to ideal conditions. PMID:23264697

Determination of thallium at ultra-trace levels in water and biological samples using solid phase spectrophotometry.

PubMed

Amin, Alaa S; El-Sharjawy, Abdel-Azeem M; Kassem, Mohammed A

2013-06-01

A new simple, very sensitive, selective and accurate procedure for the determination of trace amounts of thallium(III) by solid-phase spectrophotometry (SPS) has been developed. The procedure is based on fixation of Tl(III) as quinalizarin ion associate on a styrene-divinylbenzene anion-exchange resin. The absorbance of resin sorbed Tl(III) ion associate is measured directly at 636 and 830 nm. Thallium(I) was determined by difference measurements after oxidation of Tl(I) to Tl(III) with bromine. Calibration is linear over the range 0.5-12.0 μg L(-1) of Tl(III) with relative standard deviation (RSD) of 1.40% (n=10). The detection and quantification limits are 150 and 495 ng L(-1) using 0.6 g of the exchanger. The molar absorptivity and Sandell sensitivity are also calculated and found to be 1.31×10(7) L mol(-1)cm(-1) and 0.00156 ng cm(-2), respectively. The proposed procedure has been successfully applied to determine thallium in water, urine and serum samples. Copyright © 2013 Elsevier B.V. All rights reserved.

Characterization of Y1-xCaxBa2Cu4O8 (x=0.0˜ 0.1) with Double Cu-O Chains by Raman Spectra

NASA Astrophysics Data System (ADS)

Kodama, Yasuharu; Tanemura, Sakae; Ikeda, Teruki

1991-08-01

Raman spectra of Y1-xCaxBa2Cu4O8 (x=0.0, 0.02, 0.05 and 0.1) ceramic samples synthesized under high oxygen pressure were investigated. Seven clear peaks assigned to Ag modes were observed for the sample with x=0. With increasing x, the peaks at 238 cm-1, 332 cm-1, 430 cm-1 and 590 cm-1 were broadened. The origin of the broadening of the peaks at 238 cm-1 and 590 cm-1 is considered to be the destruction of the double Cu-O chains due to the substitution of Ca for Y.

Measuring and predicting the transport of actinides and fission product contaminants in unsaturated prairie soil

NASA Astrophysics Data System (ADS)

Sims, D. J.

Soil samples have been taken in 2001 from the area of a 1951 release from an underground storage tank of 6.7 L of an aqueous solution of irradiated uranium (360 GBq). A simulation of the dispersion of the actinides and fission products was conducted in the laboratory using irradiated natural uranium, non-irradiated natural uranium and metal standards dissolved in acidic aqueous solutions and added to soil columns containing uncontaminated prairie soil. The lab soil columns were allowed 12 to 14 months for contaminant transport. Soil samples were analyzed using gamma-ray spectroscopy, neutron activation analysis (NAA) and liquid scintillation counting (LSC) to determine the elemental concentrations of U, Cs and Sr. Diffusion coefficients from the 50 year soil samples and the lab soil samples were determined. The measured diffusion coefficients from the field samples were 3.0 x 10-4 cm2 s-1 (Cs-137), 1.8 x 10-5 cm2 s-1 (U-238) and 2.6 x 10-3 cm2 s-1 (Sr-90) and the values determined from lab simulation were 5 x 10-6 cm 2 s-1 (Cs-137), 3 x 10-5 cm2 s-1 (U-238) and 1.9 x 10-5 cm 2 s-1 (Sr-90). The differences between the sets of diffusion coefficients can be attributed to differences in retardation effects, weather effects and changes in the soil characteristics when transporting, such as porosity. The analytical work showed that Cs-137 content of soil can be determined effectively using gamma-ray spectroscopy; U-238 content can be measured using NAA; and Sr-90 content can be measured using LSC. For non- and low-radioactive species, it was shown that both flame atomic absorption spectrometry (FAAS) and inductively-coupled plasma-mass spectrometry (ICP-MS) gave comparable results for Sr, Cs and Sm, with the average values ranging from 0.5 to 4.5 ppm of each other. The U-238 content results from NAA and from ICP-MS showed general agreement with an average difference of 81.3 ppm on samples having concentrations up to 988.2 ppm. The difference may have been due to matrix interference. It was determined through finite element modeling that 250 years after the 1951 release, the soil concentration of the three contaminant of U-238, Sr-90 and Cs-137 will be less than their respective soil clearance level values and therefore will not pose a long term environmental hazard. The fastest nuclide to reach the water table, at a depth of 45 m below the surface, at Suffield Site 27 was calculated to be Sr-90 after a period of 15,000 years. Therefore, it is not necessary to remove the subsurface soil at Site 27 for site decontamination but it is recommended that a "no-digging" policy, except for scientific research, be enforced at this site.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Moradi, Hamid; Murugkar, Sangeeta; Ahmad, Abrar

Purpose: To improve classification by reducing batch effect in samples from the ovarian carcinoma cell lines A2780s (parental wild type) and A2780cp (cisplatin cross-radio-resistant), before, right after, and 24 hours after irradiation to 10Gy. Methods: Spectra were acquired with a home built confocal Raman microscope in 3 distinct runs of six samples: unirradiated s&cp (control pair), then 0h and 24h after irradiation. The Raman spectra were noise reduced, then background subtracted with SMIRF algorithm. ∼35 cell spectra were collected from each sample in 1024 channels from 700cm-1 to 1618cm-1. The spectra were analyzed by regularized multiclass LDA. For feature reductionmore » the spectra were grouped into 3 overlapping group pairs: s-cp, 0Gy–10Gy0h and 0Gy10–Gy24h. The three features, the three differences of the mean spectra were mapped to the analysis sub-space by the inverse regularized covariance matrix. The batch effect noticeably confounded the dose and time effect. Results: To remove the batch effect, the 2+2=4D subspace extended by the covariance matrix of the means of the 0Gy control groups was subtracted from the spectra of each sample. Repeating the analysis on the spectra with the control group variability removed, the batch effect was dramatically reduced in the dose and time directions enabling sharp linear discrimination. The cell type classification also improved. Conclusions: We identified a efficient batch effect removal technique crucial to the applicability of Raman microscopy to radiosensitivity studies both on cell cultures and potential clinical diagnostic applications.« less

Transmission measurement based on STM observation to detect the penetration depth of low-energy heavy ions in botanic samples.

PubMed

Liu, Feng; Wang, Yugang; Xue, Jianming; Wang, Sixue; Du, Guanhua; Zhao, Weijiang

2003-02-01

The penetration depth of low-energy heavy ions in botanic samples was detected with a new transmission measurement. In the measurement, highly oriented pyrolytic graphite (HOPG) pieces were placed behind the botanic samples with certain thickness. During the irradiation of heavy ions with energy of tens of keV, the energetic particles transmitted from those samples were received by the HOPG pieces. After irradiation, scanning tunneling microscope (STM) was applied to observe protrusion-like damage induced by these transmitted ions on the surface of the HOPG. The statistical average number density of protrusions and the minimum transmission rate of the low-energy heavy ions can be obtained. The detection efficiency of the new method for low-energy heavy ions was about 0.1-1 and the background in the measurement can be reduced to as low as 1.0 x 10(8) protrusions/cm2. With this method, the penetration depth of the energetic particles was detected to be no less than 60 micrometers in kidney bean slices when the slices were irradiated by 100 keVAr+ ion at the fluence of 5 x 10(16) ions/cm2. c2002 Elsevier Science Ltd. All rights reserved.

Transmission measurement based on STM observation to detect the penetration depth of low-energy heavy ions in botanic samples

NASA Technical Reports Server (NTRS)

Liu, Feng; Wang, Yugang; Xue, Jianming; Wang, Sixue; Du, Guanhua; Zhao, Weijiang

2003-01-01

The penetration depth of low-energy heavy ions in botanic samples was detected with a new transmission measurement. In the measurement, highly oriented pyrolytic graphite (HOPG) pieces were placed behind the botanic samples with certain thickness. During the irradiation of heavy ions with energy of tens of keV, the energetic particles transmitted from those samples were received by the HOPG pieces. After irradiation, scanning tunneling microscope (STM) was applied to observe protrusion-like damage induced by these transmitted ions on the surface of the HOPG. The statistical average number density of protrusions and the minimum transmission rate of the low-energy heavy ions can be obtained. The detection efficiency of the new method for low-energy heavy ions was about 0.1-1 and the background in the measurement can be reduced to as low as 1.0 x 10(8) protrusions/cm2. With this method, the penetration depth of the energetic particles was detected to be no less than 60 micrometers in kidney bean slices when the slices were irradiated by 100 keVAr+ ion at the fluence of 5 x 10(16) ions/cm2. c2002 Elsevier Science Ltd. All rights reserved.

[Influencing factors of soil organic carbon in deeper soil layers at a small watershed on tableland region of the Loess Plateau, China].

PubMed

Che, Sheng-guo; Guo, Sheng-li

2010-05-01

Analyzing and estimating soil organic carbon (SOC) storage and changes in deep layers under different land uses and landforms may play a pivotal role in comprehending the balance and cycle mechanisms of C cycling, and comprehending the capacity of C sequestration in the terrestrial ecosystem. The study mainly emphasized on effects of landforms and land uses on vertical distribution characteristic of SOC sampled to a depth of 200 cm at the Wangdonggou watershed on the tableland region of Loess Plateau, China. For the top soil of 0-20 cm, the order of SOC contents was gully (10.0 g x kg(-1)) > tableland (7.8 g x kg(-1)) and slopeland (8.2 g x kg(-1)). For the subsoil, SOC in tableland was higher than that in gully and slopeland. For slopeland and gully, SOC decreased with increasing depth, while for tableland, SOC decreased initially, then increased, lastly decreased. Meanwhile, for tableland, the order of SOC appeared approximately manmade grassland > cropland > orchard with the effecting depth of land uses for 40 cm, and for slopeland the order was native grassland (4.3 g x kg(-1)) > manmade woodland (3.8 g x kg(-1)) > manmade grassland (3.3 g x kg(-1)) > orchard (3.3 g x kg(-1)) with the depth for 100 cm, while for gully, there was no significantly difference (p > 0.05) among different land uses. SOC storage in the profile of 20-200 cm accounted for 67.6% sampled to a depth of 100 cm, while for 100-200cm, SOC storage accounted 37.3% in 0-200 cm equaled to 63.8% of the SOC storage in 0-100 cm. The results revealed that landforms and land uses highly significantly (p < 0.05) affected the vertical distribution of SOC at a small watershed scale and considerable amounts of C were stored at deeper depths.

Self- and Air-Broadened Line Shapes in the 2v3 P and R Branches of 12CH4

NASA Technical Reports Server (NTRS)

Devi, V. Malathy; Benner, D. Chris; Sung, Keeyoon; Crawford, Timothy J.; Yu, Shanshan; Brown, Linda R.; Smith, Mary Ann H.; Mantz, Arlan W.; Boudon, Vincent; Ismail, Syed

2015-01-01

In this paper we report line shape parameters of 12CH4 for several hundred 2V(sub 3) transitions in the spectral regions 5891-5996 cm( exp -1) (P branch) and 6015-6115 cm(exp -1) (R branch). Air- and self-broadening coefficients were measured as a function of temperature; line mixing via off-diagonal relaxation matrix element coefficients was also obtained for 47 transition pairs. In total, nearly 1517 positions and intensities were retrieved, but many transitions were too weak for the line shape study. For this analysis, we used 25 high-resolution (0.0056 and 0.0067 cm(ex[ -1) and high signal-to-noise (S/N) spectra of high-purity 12CH4 and the same high-purity 12CH4 broadened by dry air recorded at different sample temperatures between 130 K and 295 K with the Bruker IFS 125HR Fourier transform spectrometer at JPL. Three different absorption cells were used (1) a White cell set to a path length of 13.09 m for room temperature data, (2) a single-pass 0.2038 m long coolable cell (for self-broadening) and (3) a multipass cell with 20.941 m total path coolable Herriott cell (for air-broadening). In total there were 13 spectra with pure 12CH4 (0.27-599 Torr) and 12 air-broadened spectra with total sample pressures of 80-805 Torr and volume mixing ratios (VMR) of methane between 0.18 and 1.0. An interactive multispectrum nonlinear least-squares technique was employed to fit the individual P10-P1 and R0-R10 manifolds in all the spectra simultaneously. Results obtained from the present analysis are compared to other recent measurements.

Micro and macroscopic investigation to quantify tillage impact on soil hydrodynamic behaviour

NASA Astrophysics Data System (ADS)

Beckers, E.; Roisin, C.; Plougonven, E.; Deraedt, D.; Léonard, A.; Degré, A.

2012-04-01

Nowadays, tillage simplification is an increasing practice. Many advantages are cited in the literature, such as energy saving, soil conservation etc. Agricultural management practices influence soil structure, but consequent changes in soil hydrodynamic behaviour at the field scale are still not well understood. Many studies focus only on macroscopic measurements which do not provide mechanistic explanations. Moreover, research shows divergent conclusions over structure modification. The aim of this work is to fill this gap by quantifying soil structure modification depending on tillage intensity through both macroscopic and microscopic measurements, the latter improving our comprehension of the fundamental mechanisms involved. Our experiment takes place in Gentinnes (Walloon Brabant, Belgium), on a field organized in a Latin square scheme. Since 2004, plots have been cultivated in conventional tillage (CT) or in reduced tillage (RT). The latter consists in sowing after stubble ploughing of about 10cm. The crop rotation is sugar beet followed by winter wheat. The soil is mainly composed of silt loam and can be classified as a Luvisol. Macroscopic investigations consist in establishing pF and K(h) curves and 3D soil strength profiles. At the microscale, 3D morphologic parameters are measured using X-ray microtomography. Because of the variation of working depth between management practices (10cm for RT vs. 25cm for CT), two horizons were investigated: H1 between 0-10cm and H2 between 12-25cm. 3D soil strength profiles were established thanks to a fully automated penetrometer (30° angle cone with a base area of 10mm2) which covered a 160 × 80cm2 area with 5cm spacing between neighbouring points. At each node, penetration was performed and soil strength measurements were collected every 1cm from 5 to 55cm depth. K(h) curves were provided by 20cm diameter tension-infiltrometer measurements (Eijkelkamp Agrisearch Equipment). Undisturbed soil samples were removed from H1 and H2 for both management practices: 100cm3 samples were used to establish pF curves with the Richards procedure, and 35cm3 samples were used for X-ray microtomography investigation. Samples for microtomography were air-dried at 40°C in order to empty meso- and macroporosity and then scanned using a Skyscan-1172 high-resolution desktop micro-CT system (Skyscan, Kontich, Belgium). Macroscopic measurements show consistent results: penetrometry profiles confirm the presence of two different horizons for RT, with a permeable superficial horizon between 0 and 10cm and a compacted subjacent horizon. Despite the long-term experiment, the old plough pan is still observed. The superficial horizon is equivalent in terms of pF curves to CT. The second horizon in RT shows significant differences with CT: porosity and especially effective porosity are greater for CT than RT. Infiltration tests confirm these reports with a higher conductivity for CT than RT. In fact, the first permeable horizon for RT is thin and the second horizon impacts vertical infiltration. These observations will be completed with microtomograms analysis. Pore size distribution, but particularly morphological parameters like eccentricity, orientation, connectivity and anisotropy of the pore network will be quantified and connected with macroscopic measurements.

National Centers for Environmental Prediction

Science.gov Websites

) soilm1 0-10cm soil moisture soilm2 10-40cm soil moisture soilm3 40-100cm soil moisture soilm4 100-200cm soil moisture soilt1 0-10cm soil temperature soilt2 10-40cm soil temperature soilt3 40-100cm soil temperature soilt4 100-200cm soil temperature thick700.ptype 850-700mb thickness precipitation type thick850

Indirect spectrophotometric determination of small amounts of selenium(IV) and arsenic(V) by simple extraction using flotation columns.

PubMed

Mostafa, G A; Ghazy, S E

2001-10-01

A simple, rapid and selective procedure for the indirect spectrophotometric determination of Se(IV) and As(V) has been developed. It is based on the reduction of Se(IV) to Se(0) and As(V) to As(III) with hydroiodic acid (KI + HCl). The liberated iodine, equivalent to each analyte, is quantitatively extracted with oleic acid (HOL) surfactant. The iodine-HOL system exhibits its maximum absorbance at 435 nm. The different analytical parameters affecting the extraction and determination processes have been examined. The calibration graphs were found to be linear over the ranges 5-120 and 0.25-20 ppm of Se(IV) and As(V), with lower detection limits of 2.5 and 0.15 ppm and molar absorptivities of 1 x 10(4) and 0.5 x 10(4) dm3 mol(-1) cm(-1), respectively. Sandell's sensitivity was calculated to be 0.0078 and 0.0149 microg/cm2 in the same order. The relative standard deviation for five replicate analyses of 40 ppm Se(IV) and 4 ppm As(V) were 1.0 and 0.9%, respectively. The proposed procedure in the presence of EDTA as a masking agent for foreign ions has been successfully applied to the determination of Se(IV) in a reference sample and As(V) in copper metal, in addition to their determination in spiked and polluted water samples.

Temperature dependence of electrical properties of gallium-nitride bulk single crystals doped with Mg and their evolution with annealing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Litwin-Staszewska, E.; Suski, T.; Piotrzkowski, R.

Comprehensive studies of the electrical properties of Mg-doped bulk GaN crystals, grown by high-pressure synthesis, were performed as a function of temperature up to 750{degree}C. Annealing of the samples in nitrogen ambient modifies qualitatively their resistivity values {rho} and the {rho}(T) variation. It was found that our material is characterized by a high concentration of oxygen-related donors and that the charge transport in the studied samples is determined by two types of states, one of shallow character (Mg-related state, E{sub A}{approximately}0.15eV), and the second one much more deep, E{sub 2}{approximately}0.95eV (above the valence band). Depending on the effective concentration ofmore » either states, different resistivities {rho} can be observed: lower resistivity ({rho}{lt}10{sup 4}{Omega}cm at ambient temperature) in samples with dominant E{sub A} states and very high resistivity ({rho}{gt}10{sup 6}{Omega}cm at ambient temperature) in samples with dominant E{sub 2} states. For the first type of samples, annealing at T{sub ann}{lt}500{degree}C leads to a decrease of their resistivity and is associated with an increase of the effective concentration of the shallow Mg acceptors. Annealing of both types of samples at temperatures between 600 and 750{degree}C leads to an increase of the deep state concentration. The presence of hydrogen ambient during annealing of the low-resistivity samples strongly influences their properties. The increase of the sample resistivity and an appearance of a local vibrational mode of hydrogen at 3125 cm{minus}1 were observed. These effects can be removed by annealing in hydrogen-free ambient. {copyright} 2001 American Institute of Physics.« less

Development of a case-mix funding system for adults with combined vision and hearing loss

PubMed Central

2013-01-01

Background Adults with vision and hearing loss, or dual sensory loss (DSL), present with a wide range of needs and abilities. This creates many challenges when attempting to set the most appropriate and equitable funding levels. Case-mix (CM) funding models represent one method for understanding client characteristics that correlate with resource intensity. Methods A CM model was developed based on a derivation sample (n = 182) and tested with a replication sample (n = 135) of adults aged 18+ with known DSL who were living in the community. All items within the CM model came from a standardized, multidimensional assessment, the interRAI Community Health Assessment and the Deafblind Supplement. The main outcome was a summary of formal and informal service costs which included intervenor and interpreter support, in-home nursing, personal support and rehabilitation services. Informal costs were estimated based on a wage rate of half that for a professional service provider ($10/hour). Decision-tree analysis was used to create groups with homogeneous resource utilization. Results The resulting CM model had 9 terminal nodes. The CM index (CMI) showed a 35-fold range for total costs. In both the derivation and replication sample, 4 groups (out of a total of 18 or 22.2%) had a coefficient of variation value that exceeded the overall level of variation. Explained variance in the derivation sample was 67.7% for total costs versus 28.2% in the replication sample. A strong correlation was observed between the CMI values in the two samples (r = 0.82; p = 0.006). Conclusions The derived CM funding model for adults with DSL differentiates resource intensity across 9 main groups and in both datasets there is evidence that these CM groups appropriately identify clients based on need for formal and informal support. PMID:23587314

Anaerobic oxidation of methane in sediments of two boreal lakes

NASA Astrophysics Data System (ADS)

Rissanen, Antti J.; Karvinen, Anu; Nykänen, Hannu; Mpamah, Promise; Peura, Sari; Tiirola, Marja; Kankaala, Paula

2014-05-01

Anaerobic oxidation of methane (AOM) is a considerable sink for methane (CH4) in marine systems, but very little is known about the occurrence and importance of the process in freshwater systems. In addition, much about the microbial communities involved in AOM is unclear. AOM coupled with sulfate reduction is the dominant AOM process in marine systems but the scarce existing data suggest that, in freshwater systems, AOM coupled with reduction of alternative electron acceptors (nitrate/nitrite, manganese, iron) is more important. In this study, potential for AOM coupled with metal reduction was studied in boreal lake sediments. Slurries of sediment samples collected from two sites in southeastern Finland, i.e. from Lake Orivesi, Heposelkä, an vegetated littoral site, dominated by Phragmites australis (Sample Sa, sediment layer 0 - 25 cm) and from the profundal zone of a mesotrophic Lake Ätäskö (Aa, 0 - 10 cm; Ab, 10 - 30 cm; Ac, 90 - 130 cm), were incubated in laboratory in anaerobic conditions at in situ temperatures for up to 5 months. The samples were amended either 1) with 13CH4, 2) 13CH4 + manganese(II) oxide (MnO) or 3) 13CH4 + iron(III) hydroxide (Fe(OH)3), and the processes were measured by following the 13C transfer to the carbon dioxide (CO2) pool and by concentration measurements of CH4 and CO2. Changes in microbial communities were studied from DNA extracted from sediment samples before and after incubation period by next-generation sequencing (Ion Torrent) of polymerase chain reaction (PCR) - amplified bacterial and archaeal 16S rRNA and methyl coenzyme-M reductase gene (mcrA) amplicons. Increase in 13C of CO2 gas confirmed that AOM took place in sediments of both study lakes. In general, 13CO2 - production was significant both at the beginning (0 - 21 days) and at the end (84 - 151 days) of incubation period. Potential AOM rates (calculated based on 13CO2 - production) varied considerably and were much lower in deep sediment (Sample Ac), 0.1 - 0.2 nmol CH4 d-1gwetsediment-1, than in surface sediment samples (Samples Aa, Ab and Sa), 0.2 - 12.3 nmol CH4 d-1gwetsediment-1. AOM took place without metal additions in every sample type. Addition of MnO increased potential AOM rates in surface sediment samples but not in deep sediment samples. Addition of Fe(OH)3increased AOM significantly only in Aa samples. Molecular microbiological analyses are currently in progress and the results will be shown in the poster presentation.

Association between the Infant and Child Feeding Index (ICFI) and nutritional status of 6- to 35-month-old children in rural western China.

PubMed

Qu, Pengfei; Mi, Baibing; Wang, Duolao; Zhang, Ruo; Yang, Jiaomei; Liu, Danmeng; Dang, Shaonong; Yan, Hong

2017-01-01

The objective of this study was to determine the relationship between the quality of feeding practices and children's nutritional status in rural western China. A sample of 12,146 pairs of 6- to 35-month-old children and their mothers were recruited using stratified multistage cluster random sampling in rural western China. Quantile regression was used to analyze the relationship between the Infant and Child Feeding Index (ICFI) and children's nutritional status. In rural western China, 24.37% of all infants and young children suffer from malnutrition. Of this total, 19.57%, 8.74% and 4.63% of infants and children are classified as stunting, underweight and wasting, respectively. After adjusting for covariates, the quantile regression results suggested that qualified ICFI (ICFI > 13.8) was associated with all length and HAZ quantiles (P<0.05) and had a greater effect on the following: poor length and HAZ, the β-estimates (length) from 0.76 cm (95% CI: 0.53 to 0.99 cm) to 0.34 cm (95% CI: 0.09 to 0.59 cm) and the β-estimates (HAZ) from 0.17 (95% CI: 0.10 to 0.24) to 0.11 (95% CI: 0.04 to 0.19). Qualified ICFI was also associated with most weight quantiles (P<0.05 except the 80th and 90th quantiles) and poor and intermediate WAZ quantiles (P<0.05 including the 10th, 20th 30th and 40th quantiles). Additionally, qualified ICFI had a greater effect on poor weight and WAZ quantiles in which the β-estimates (weight) were from 0.20 kg (95% CI: 0.14 to 0.26 kg) to 0.06 kg (95% CI: 0.00 to 0.12 kg) and the β-estimates (WAZ) were from 0.14 (95% CI: 0.08 to 0.21) to 0.05 (95% CI: 0.01 to 0.10). Feeding practices were associated with the physical development of infants and young children, and proper feeding practices had a greater effect on poor physical development in infants and young children. For mothers in rural western China, proper guidelines and messaging on complementary feeding practices are necessary.

Relationship between fire temperature and changes in chemical soil properties: a conceptual model of nutrient release

NASA Astrophysics Data System (ADS)

Thomaz, Edivaldo L.; Doerr, Stefan H.

2014-05-01

The purpose of this study was to evaluate the effects of fire temperatures (i.e., soil heating) on nutrient release and aggregate physical changes in soil. A preliminary conceptual model of nutrient release was established based on results obtained from a controlled burn in a slash-and-burn agricultural system located in Brazil. The study was carried out in clayey subtropical soil (humic Cambisol) from a plot that had been fallow for 8 years. A set of three thermocouples were placed in four trenches at the following depths: 0 cm on the top of the mineral horizon, 1.0 cm within the mineral horizon, and 2 cm within the mineral horizon. Three soil samples (true independent sample) were collected approximately 12 hours post-fire at depths of 0-2.5 cm. Soil chemical changes were more sensitive to fire temperatures than aggregate physical soil characteristics. Most of the nutrient response to soil heating was not linear. The results demonstrated that moderate temperatures (< 400°C) had a major effect on nutrient release (i.e., the optimum effect), whereas high temperatures (> 500 °C) decreased soil fertility.

Life-history traits of the long-nosed skate Dipturus oxyrinchus.

PubMed

Bellodi, A; Porcu, C; Cannas, R; Cau, Al; Marongiu, M F; Mulas, A; Vittori, S; Follesa, M C

2017-03-01

This work investigates life-history traits of the long-nosed skate Dipturus oxyrinchus, which is a common by-catch in Sardinian waters. The reproductive variables were analysed from 979 specimens sampled during scientific and commercial hauls. Females (10·4-117·5 cm total length, L T ) attained larger sizes than males (14·5-99·5 cm L T ). To evaluate age and growth, a sub-sample of 130 individuals (76 females and 54 males) were used. The age was estimated by annuli counts of sectioned vertebral centra. Four models were used for the length-at-age data: the von Bertalanffy, the exponential, the Gompertz and the logistic functions. According to the Akaike's information criterion, the Gompertz model seemed to provide the best fitting curve (L ∞ mean ± s.e.: 127·55 ± 4·90 cm, k: 0·14 ± 0·09, IP: 3·97 ± 0·90 years). The oldest female and male were aged 17 (115·5 cm L T ) and 15 years (96·0 cm L T ), respectively. Lengths at maturity were 103·5 cm for females and 91·0 cm for males, corresponding to 90% of the maximum observed length in both sexes. The monthly distribution of maturity stages highlighted an extended reproductive cycle, with spawning females and active males being present almost throughout the year, as confirmed by the gonado-somatic index. Ovarian fecundity reached a maximum of 26 yolked follicles with a mean ± s.e. size of 19·7 ± 6·5 mm. © 2016 The Fisheries Society of the British Isles.

Limits on variations in fundamental constants from 21-cm and ultraviolet Quasar absorption lines.

PubMed

Tzanavaris, P; Webb, J K; Murphy, M T; Flambaum, V V; Curran, S J

2005-07-22

Quasar absorption spectra at 21-cm and UV rest wavelengths are used to estimate the time variation of x [triple-bond] alpha(2)g(p)mu, where alpha is the fine structure constant, g(p) the proton g factor, and m(e)/m(p) [triple-bond] mu the electron/proton mass ratio. Over a redshift range 0.24 < or = zeta(abs) < or = 2.04, (Deltax/x)(weighted)(total) = (1.17 +/- 1.01) x 10(-5). A linear fit gives x/x = (-1.43 +/- 1.27) x 10(-15) yr(-1). Two previous results on varying alpha yield the strong limits Deltamu/mu = (2.31 +/- 1.03) x 10(-5) and Deltamu/mu=(1.29 +/- 1.01) x10(-5). Our sample, 8 x larger than any previous, provides the first direct estimate of the intrinsic 21-cm and UV velocity differences 6 km s(-1).

Role of Sediments and Nutrients in the Condition of a Coral Reef Under Tourist Pressure: Akumal México.

NASA Astrophysics Data System (ADS)

Naranjo-Garcia, M. J.; Vadés Lozano, D. S.; Real-De-Leon, E.; Lopez-Aguiar, K.; Garza-Perez, J. R.

2014-12-01

Akumal, Mexico, was the first tourist resort in the Mexican Caribbean mainland, its highly developed coastal zone lies directly above the phreatic, and it is directly connected to the sub-littoral waters. Akumal is also known as a well-developed fringing coral reef, now in a critical condition. The main objective of this study was to explore the relationship between two of the main indicators of human pressure (nutrients and sedimentation, linked to coastal development and water run-offs) and the condition of the reef benthos, during a year. The sampling design used four transects perpendicular to shore, associated to different tourist and water run-off exposure, for a total of 12 stations distributed in three different reef zones (transition zone, shallow and deep spurs and grooves). Monthly samples were collected: water samples close to the reef lagoon drain channels and at bottom depth at each station, and sediment traps were recovered and replaced also at each station. Reef Benthos videotransects were recorded bi-monthly at each station to assess its condition. Macroalgae and filamentous algae dominate benthic cover (up to 50%), hard-coral cover ranges from 5-9%. Five coral-diseases were recorded, affecting 10.16% of the coral colonies: Caribbean Ciliate Infection, White Band, Purple Spots, White Spots and Yellow Band. The sedimentation rate -sr- ranged from 0.13 to 83.7 mg/cm2/day during the year; 86% of the samples had a sr ≤ 10 mg/cm2/day (reefs not stressed); 13% of the samples had a sr ranging from 10 to 50 mg/cm2/day (stressed reefs); and 1% of the samples were over the critical threshold (>50 mg/cm2/day). Dissolved Inorganic Nitrogen concentrations during the year were above those recorded previously in Caribbean reefs. The most abundant fraction was ammonium, surpassing both Mexican norms: For protection of aquatic life in coastal zones (0.01 mg/L), and the critical threshold for aquatic life (0.4 mg/L). These concentration limits are considered as drivers of eutrophication, one of the main established causes of reef degradation globally. High concentrations of ammonium and other nutrients have been linked to increases in algae cover and coral diseases incidence, and to decreases in rates of coral calcification, fertility, production and viability of coral larvae, and the associated diversity loss.

Cerebral malaria and sequelar epilepsy: first matched case-control study in Gabon.

PubMed

Ngoungou, Edgard Brice; Koko, Jean; Druet-Cabanac, Michel; Assengone-Zeh-Nguema, Yvonne; Launay, Marylène Ndong; Engohang, Edouard; Moubeka-Mounguengui, Martine; Kouna-Ndouongo, Philomène; Loembe, Paul-Marie; Preux, Pierre-Marie; Kombila, Maryvonne

2006-12-01

Cerebral malaria (CM) is suspected to be a potential cause of epilepsy in tropical areas. The purpose of this article was to evaluate the relationship between CM and epilepsy in Gabon. A matched case-control study was carried out on a sample of subjects aged six months to 25 years and hospitalized between 1990 and 2004 in three hospitals in Libreville, Gabon. Cases were defined as patients suffering from epilepsy and confirmed by a neurologist. Controls were defined as patients without epilepsy. The exposure of interest was CM according to WHO criteria. In total, 296 cases and 296 controls were included. Of these, 36 (26 cases and 10 controls) had a CM history. The adjusted odds ratio (aOR) to develop epilepsy after CM was 3.9 [95% CI: 1.7-8.9], p<0.001. Additional risk factors were identified: family history of epilepsy: aOR=6.0 [95% CI: 2.6-14.1], p<0.0001, and febrile convulsions: aOR=9.2 [95% CI 4.0-21.1], p<0.0001. This first case-control study on that issue suggests that epilepsy-related CM is an underrecognized problem. It emphasizes the need for further studies to better evaluate the role of convulsions during CM.

Effects of high power ultrasound on microflora, enzymes and some quality attributes of a strawberry drink.

PubMed

Chen, Liyi; Bi, Xiufang; Cao, Xiamin; Liu, Lei; Che, Zhenming

2018-04-16

The objective of the present work was to study the effect of high power ultrasound (HPU) on microflora, enzymes and some quality attributes of a strawberry drink and to provide a theoretical basis for strawberry drinks processing, which was conducive to the development of more nutritious and healthier strawberry drinks. Fresh strawberry drink was subjected to HPU treatment at 20 kHz (242 W cm -2 , 605 W cm -2 and 968 W cm -2 ) for 2, 4, 6, 8, 10 min in an ice bath. Results showed the polyphenol oxidase (PPO), pectin methylesterase (PME) and β-glucosidase activity were decreased by 44.90%, 89.11% and 84.71% at 968 W cm -2 and 10 min, respectively. A lower L* value, a* value, b* value and a higher browning degree (BD) value was observed in HPU treated samples, resulting in a significant increase in ΔE values (p<0.05). HPU treatment caused loss in viscosity and turbidity, while the total soluble solid (TSS) and pH of the strawberry drink were stable. The total phenols content and antioxidant capacity increased while anthocyanins content decreased compared with untreated samples. Total aerobic bacteria (TAB) and mould and yeast (M & Y) was reduced by 2.07 and 1.13 log 10 cycles at 968 W cm -2 and 10 min. HPU can effectively achieve the effect of pasteurization and maintain the nutrients of the strawberry drink. This article is protected by copyright. All rights reserved.

Microbiological quality and potential public health risks of export meat from springbok (Antidorcas marsupialis) in Namibia.

PubMed

Magwedere, K; Shilangale, R; Mbulu, R S; Hemberger, Y; Hoffman, L C; Dziva, F

2013-01-01

To assess the microbiological quality and safety of export game meat; i) a total of 80 pooled meat samples for aerobic plate count (APC) and Enterobacteriaceae ii) water used in harvesting and processing for microbiological quality and iii) meat and rectal contents for Salmonella spp. and Shiga toxin Escherichia coli (STEC) were evaluated in 2009 and 2010. No differences (p>0.05) in the APCs were observed between the years, but the mean Enterobacteriaceae count for 2009 was 1.33 ± 0.69 log(10)cfu/cm(2) compared to 2.93 ± 1.50 log(10)cfu/cm(2) for 2010. Insignificant Heterotrophic Plate Count (HPC) levels were detected in 9/23 field water samples, while fecal bacterial (coliforms, Clostridium perfringens and enterococci) were absent in all samples. No Salmonella spp. was isolated and all E. coli isolates from meat were negative for STEC virulence genes (stx1, stx2, eae and hlyA), suggesting a negligible role by springbok in the epidemiology of STEC and Salmonella. Copyright © 2012 Elsevier Ltd. All rights reserved.

Reduced Net Erosion of High-Z PFC Materials in DIII-D Divertor

NASA Astrophysics Data System (ADS)

Rudakov, D. L.; Stangeby, P. C.; Elder, J. D.; Wampler, W. R.; Buchenauer, D. A.; Watkins, J. G.; Brooks, J. N.; Hassanein, A.; Sizyuk, T.; Briesemeister, A. R.; McLean, A. G.; Chrobak, C. P.; Guo, H. Y.; Leonard, A. W.; Wong, C. P. C.

2014-10-01

DiMES samples featuring 1 cm and 1 mm diameter W films deposited on a Si substrate were exposed in DIII-D near the attached outer strike point of LSN L-mode discharges. The measured net and gross erosion rates of W, determined from post-mortem ion beam analysis (IBA) of 1 cm and 1 mm samples, were 0.14 and 0.48 nm/s, respectively, giving net/gross erosion ratio of 0.29. REDEP/WBC modeling of this experiment yielded a very close ratio of 0.33. Projection of the modeling results to ITER shows very low net erosion of W. In another experiment Mo-coated samples were exposed with 13CH4 gas injected ~2 cm upstream of DiMES. Reduction of Mo erosion was evidenced in - situ by the suppression of MoI line radiation. Post-mortem IBA showed that the net erosion of Mo was below the measurement resolution of 0.5 nm, corresponding to a rate of <=0.07 nm/s. Compared to the previously measured erosion rates, this constitutes a reduction of more than 10X. Work supported in part the by US DOE under DE-FG02-07ER54917, DE-AC04-94AL85000, DE-AC05-00OR22725, DE-AC52-07NA27344 & DE-FC02-04ER54698.

Seed bank and established vegetation in the last remnants of the Mexican Central Plateau wetlands: the Lerma marshes.

PubMed

Zepeda, Carmen; Lot, Antonio; Nemiga, Xanat Antonio; Manjarrez, Javier

2014-06-01

Seed banks play a central role in vegetation dynamics of many wetlands. Therefore, knowledge of seed reservoirs in the soils of aquatic communities should provide useful tools for conservation and restoration efforts. This study was conducted in the Lerma marshes, one of the last remnants of the vast wetlands that were once in the Mexican Central Plateau. The main objective was to determine the composition and abundance of seed bank and its relationship with established vegetation of the three Lerma marshes. In each marsh, we systematically selected 18 to 40 sampling sites. In each site, the composition of vascular plant vegetation was evaluated in two 10m lines perpendicular to the shore. Every 0.5m, we determined the coverage of species by measuring the intercepted length for each plant or group of plants. At each sampling site where we had evaluated the established vegetation, we collected a sample of the top 10cm of sediment; the soil cores were divided into an upper layer (0-5cm) and a lower layer (5-10cm). These samples were used to evaluate the seed bank by the seedling emergence method. All samples were placed in a greenhouse at 20-25 degrees C and remained flooded for 15 weeks. Forty-nine species were recorded in the vegetation. Chiconahuapan had the richest and most diverse flora and the greatest number of perennial species. A life-forms analysis showed that perennial herbs, especially rooted-emergent hydrophytes, dominated in the three wetlands. Sixty-one species were identified in the total seed bank; Chimaliapan had the most diverse total seed bank, whereas the mean seedling density was higher in Chignahuapan. Only two species of the total seed bank of each marsh had a density greater than 10% of the total, and more than half were uncommon. The upper layer of sediment (0-5cm) contained two times more seeds/m2 and species per sample than the lower layer (5-10cm), and there was a significant decrease of seed density with depth. The detrended correspondence analysis produced a clear separation between the composition of the seed banks and established vegetation. In general, in each marsh there was less species diversity in the established vegetation than in the seed bank. Dominance by a few species in the seed bank, the presence of opportunistic species, and the low representation of established species in the seed bank suggest wetland degradation and a low probability of regenerating the natural communities from the seed bank. To ensure the permanence of these marshes, their biodiversity, and therefore the environmental services they provide, up to date planning is a must, and efforts to control and monitor hydrology, water quality, and the influence of human activities are suggested.

The influence of temperature induced phase transition on the energy storage density of anti-ferroelectric ceramics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yi, Jinqiao; Zhang, Ling; Xie, Bing

2015-09-28

Anti-ferroelectric (AFE) composite ceramics of (Pb{sub 0.858}Ba{sub 0.1}La{sub 0.02}Y{sub 0.008})(Zr{sub 0.65}Sn{sub 0.3}Ti{sub 0.05})O{sub 3}-(Pb{sub 0.97}La{sub 0.02})(Zr{sub 0.9}Sn{sub 0.05} Ti{sub 0.05})O{sub 3} (PBLYZST-PLZST) were fabricated by the conventional solid-state sintering process (CS), the glass-aided sintering (GAS), and the spark plasma sintering (SPS), respectively. The influence of the temperature induced phase transition on the phase structure, hysteresis loops, and energy storage properties of the composite ceramics were investigated in detail. The measured results of X-ray diffraction demonstrate that the composite ceramics exhibit the perovskite phases and small amounts of non-functional pyrochlore phases. Compared with the CS process, the GAS and SPS processesmore » are proven more helpful to suppress the diffusion behaviors between the PBLYZST and PLZST phases according to the field emission scanning electron microscopy, thereby being able to improve the contribution of PBLYZST phase to the temperature stability of the orthogonal AFE phase. When the ambient temperature rises from 25 °C to 125 °C, CS and GAS samples have undergone a phase transition from orthorhombic AFE phase to tetragonal AFE phase, which results in a sharp decline in the energy storage density. However, the phase transition temperature of SPS samples is higher than 125 °C, and the energy storage density only slightly decreases due to the disorder of material microstructure caused by the high temperature. As a result, the SPS composite ceramics obtain a recoverable high energy storage density of 6.46 J/cm{sup 3} and the excellent temperature stability of the energy storage density of 1.16 × 10{sup −2} J/°C·cm{sup 3}, which is 1.29 × 10{sup −2} J/°C·cm{sup 3} lower than that of CS samples and about 0.43 times as that of GAS samples.« less

Synthesis and oxygen content dependent properties of hexagonal DyMnO[subscript 3+delta

DOE Office of Scientific and Technical Information (OSTI.GOV)

Remsen, S.; Dabrowski, B.; Chmaissem, O.

2011-10-28

Oxygen deficient polycrystalline samples of hexagonal P6{sub 3}cm (space group No.185) DyMnO{sub 3+{delta}} ({delta} < 0) were synthesized in Ar by intentional decomposition of its perovskite phase obtained in air. The relative stability of these phases is in accord with our previous studies of the temperature and oxygen vacancy dependent tolerance factor. Thermogravimetric measurements have shown that hexagonal samples of DyMnO{sub 3+{delta}} (0 {le} {delta} {le} 0.4) exhibit unusually large excess oxygen content, which readily incorporates on heating near 300 C in various partial-pressures of oxygen atmospheres. Neutron and synchrotron diffraction data show the presence of two new structural phasesmore » at {delta} {approx} 0.25 (Hex{sub 2}) and {delta} {approx} 0.40 (Hex{sub 3}). Rietveld refinements of the Hex{sub 2} phase strongly suggest it is well modeled by the R3 space group (No.146). These phases were observed to transform back to P6{sub 3}cm above {approx} 350 C when material becomes stoichiometric in oxygen content ({delta} = 0). Chemical expansion of the crystal lattice corresponding to these large changes of oxygen was found to be 3.48 x 10{sup -2} mol{sup -1}. Thermal expansion of stoichiometric phases were determined to be 11.6 x 10{sup -6} and 2.1 x 10{sup -6} K{sup -1} for the P6{sub 3}cm and Hex{sub 2} phases, respectively. Our measurements also indicate that the oxygen non-stoichiometry of hexagonal RMnO{sub 3+{delta}} materials may have important influence on their multiferroic properties.« less

Nutritional characteristics of camelina meal for 3-week-old broiler chickens.

PubMed

Pekel, A Y; Kim, J I; Chapple, C; Adeola, O

2015-03-01

Limited information on nutritional characteristics on camelina meal for broiler chickens limits its use in diets of broiler chickens. The objectives of this study were to determine the ileal digestible energy (IDE), ME, and MEn contents of 2 different camelina meal (CM1 and CM2) samples for 3-wk-old broiler chickens using the regression method and to determine glucosinolate compounds in the camelina meal samples. The CM1 and CM2 were incorporated into a corn-soybean meal-based reference diet at 3 levels (0, 100, or 200 g/kg) by replacing the energy-yielding ingredients. These 5 diets (reference diet, and 100 and 200 g/kg camelina meal from each of CM1 and CM2) were fed to 320 male Ross 708 broilers from d 21 to 28 post hatching with 8 birds per cage and 8 replicates per treatment in a randomized complete block design. Excreta were collected twice daily from d 25 to 28, and jejunal digesta and ileal digesta from the Meckel's diverticulum to approximately 2 cm proximal to the ileocecal junction were collected on d 28. The total glucosinolate content for CM1 and CM2 were 24.2 and 22.7 nmol/mg, respectively. Jejunal digesta viscosity was linearly increased (P<0.001) from 2.2 to 4.1 cP with increasing dietary camelina meal levels. There were linear effects (P<0.001) of CM1 and CM2 substitution on final weight, weight gain, feed intake, and G:F. The inclusion of CM1 and CM2 linearly decreased (P<0.001) ileal digestibility of DM, energy, and IDE. The supplementation of CM1 and CM2 linearly decreased (P<0.001) the retention of DM, nitrogen, and energy; ME, and MEn. By regressing the CM1 and CM2-associated IDE intake in kilocalories against kilograms of CM1 and CM2 intake, the IDE regression equation was Y=-10+1,429×CM1+2,125×CM2, r2=0.55, which indicates that IDE values were 1,429 kcal/kg of DM for CM1 and 2,125 kcal/kg of DM for CM2. The ME regression was Y=5+882×CM1+925×CM2, r2=0.54, which implies ME values of 882 kcal/kg of DM for CM1 and 925 kcal/kg of DM for CM2. MEn regression was Y=2+795×CM1+844×CM2, r2=0.52, which implies MEn values of 795 kcal/kg of DM for CM1 and 844 kcal/kg of DM for CM2. Based on these results, utilization of energy and nitrogen in camelina meal by broiler chickens is low and the high viscosity observed in jejunal digesta as well as the total glucosinolate in camelina meal may have contributed to the poor energy and nitrogen utilization. © 2015 Poultry Science Association Inc.

Source and movement of helium in the eastern Morongo groundwater Basin: The influence of regional tectonics on crustal and mantle helium fluxes

USGS Publications Warehouse

Kulongoski, J.T.; Hilton, David R.; Izbicki, J.A.

2005-01-01

We assess the role of fracturing and seismicity on fluid-driven mass transport of helium using groundwaters from the eastern Morongo Basin (EMB), California, USA. The EMB, located ???200 km east of Los Angeles, lies within a tectonically active region known as the Eastern California Shear Zone that exhibits both strike-slip and extensional deformation. Helium concentrations from 27 groundwaters range from 0.97 to 253.7 ?? 10-7 cm3 STP g-1 H2O, with corresponding 3He/4He ratios falling between 1.0 and 0.26 RA (where RA is the 3He/4He ratio of air). All groundwaters had helium isotope ratios significantly higher than the crustal production value of ???0.02 RA. Dissolved helium concentrations were resolved into components associated with solubility equilibration, air entrainment, in situ production within the aquifer, and extraneous fluxes (both crustal and mantle derived). All samples contained a mantle helium-3 (3Hem) flux in the range of 4.5 to 1351 ?? 10-14 cm3 STP 3He cm-2 yr-1 and a crustal flux (J0) between 0.03 and 300 ?? 10-7 cm3 STP 4He cm-2 yr-1. Groundwaters from the eastern part of the basin contained significantly higher 3Hem and deep crustal helium-4 (4Hedc) concentrations than other areas, suggesting a localized source for these components. 4Hedc and 3Hem are strongly correlated, and are associated with faults in the basin. A shallow thermal anomaly in a >3,000 m deep graben in the eastern basin suggests upflow of fluids through active faults associated with extensional tectonics. Regional tectonics appears to drive large scale crustal fluid transport, whereas episodic hydrofracturing provides an effective mechanism for mantle-crust volatile transport identified by variability in the magnitude of degassing fluxes (3Hem and J0) across the basin. Copyright ?? 2005 Elsevier Ltd.

[Transport of mucoid mucus in healthy individuals and patients with chronic obstructive pulmonary disease and bronchiectasis].

PubMed

Lima Afonso, J; Tambascio, J; Dutra de Souza, H C; Jardim, J R; Baddini Martinez, J A; Gastaldi, A C

2013-01-01

To characterise and compare the in vitro transport properties of respiratory mucoid secretion in individuals with no lung disease and in stable patients with chronic obstructive pulmonary disease (COPD) and bronchiectasis. Samples of mucus were collected, from 21 volunteers presenting no lung disease who had undergone surgery, from 10 patients presenting chronic COPD, and from 16 patients with bronchiectasis. Mucociliary transport (MCT), transport by cough (SCM), and contact angle (CAM) were evaluated. MCT was found to be greater in healthy individuals (1.0±0.19) than in COPD (0.91±0.17) and bronchiectasis (0.76±0.23) patients (p<0.05), whereas SCM was greater in COPD patients (16.31±7.35 cm) than in patients with bronchiectasis (12.16±6.64 cm) and healthy individuals (10.50±25.8 cm) (p<0.05). No significant differences were observed between the groups regarding CAM. Mucus from healthy individuals allows better mucociliary transport compared to that from patients with lung diseases. However, the mucus from COPD patients allows a better transport by coughing, demonstrating that these individuals have adapted to a defence mechanism compared to patients with bronchiectasis, who have impairment in their ciliary and cough transport mechanisms. Copyright © 2012 Sociedade Portuguesa de Pneumologia. Published by Elsevier España. All rights reserved.

Optical absorption coefficient, time of thermal relaxation, time of surface threshold, and time of heat incubation for PMMA samples at the CO2 laser-beam wavelength of 10.6 microm.

PubMed

Canestri, Franco

2006-10-01

This paper discusses in detail the mathematical identification of the optical absorption alpha (cm(1)) of Beer's law, a crucial parameter to study the development of laser beam craters into dry poly(methyl methacrylate) (PMMA) samples exposed to steady CO(2) laser beams emitting radiation at lambda = 10.6 microm in continuous- wave (CW) mode. Three additional time-dependent coefficients have been determined as well. In clinical applications, these results are important in order to precisely quantify and forecast the ablation capabilities of the CO(2) laser beam, to optimize its usage in the operating room, and to address the safety issues related to surgical interventions on human tissue. Currently, the data available in the literature do not allow the identification of the numerical value of alpha (cm(1)) for PMMA at lambda = 10.6 microm with enough, and therefore satisfactory, accuracy. Additionally, the correct identification of the optical absorption of PMMA would allow the isolation, with better accuracy, of other key time-dependent coefficients, such as relaxation time, surface threshold time, and heat incubation time, which are all described in the literature in a qualitative rather than quantitative fashion. Correct bone cement preparation depends on the value of alpha (cm(1)) of the PMMA in order to avoid unwanted complications in patients during cement removal via laser techniques. The laser in use was configured in different combinations with the following parameters: transverse electromagnetic modes (TEMnm), output power (I0), exposure times (te), and focal lengths (fk). Several PMMA blocks (1 cm x 4 cm x 4 cm) were exposed to CW radiation of three commercially available CO(2) medical laser devices showing a TEM11 mode. Each block was exposed to the beam on a horizontal and well-polished surface of each sample. Four focal lengths (2.5", 5", 7.5", and 15.75" [400 mm]) were used to focus the beam on the well-polished and dry surface of the PMMA samples. The resulting dimensions of the craters were measured after each exposure, which has been kept at a 10-Watt CW beam. Exposure time ranged from 0.5 to 2 sec. The value of alpha = 502 (cm(1)) for PMMAat 10.6 microm was identified, matching other results reported in the literature for similar compact media in the absence of water content, such as PMMA. The time of thermal relaxation was 9.358 x 10(4) sec, the time of surface threshold was 9.365 x 10(4) sec, and the time of heat incubation was 3.6 x 10(7) sec (all three for PMMAat 10.6 microm for any exposure). Using the calculated value of alpha, one of the practical clinical recommendations would be, for instance, to reduce or to abolish the utilization of colorant dopants in the preparation of the bone cement mixture and therefore reduce the danger of bone damage possible during the removal of bone cement via laser techniques. Other examples refer to other clinical bone and dental treatments.

Upper limits on the 21 cm power spectrum at z = 5.9 from quasar absorption line spectroscopy

NASA Astrophysics Data System (ADS)

Pober, Jonathan C.; Greig, Bradley; Mesinger, Andrei

2016-11-01

We present upper limits on the 21 cm power spectrum at z = 5.9 calculated from the model-independent limit on the neutral fraction of the intergalactic medium of x_{H I} < 0.06 + 0.05 (1σ ) derived from dark pixel statistics of quasar absorption spectra. Using 21CMMC, a Markov chain Monte Carlo Epoch of Reionization analysis code, we explore the probability distribution of 21 cm power spectra consistent with this constraint on the neutral fraction. We present 99 per cent confidence upper limits of Δ2(k) < 10-20 mK2 over a range of k from 0.5 to 2.0 h Mpc-1, with the exact limit dependent on the sampled k mode. This limit can be used as a null test for 21 cm experiments: a detection of power at z = 5.9 in excess of this value is highly suggestive of residual foreground contamination or other systematic errors affecting the analysis.

Characterization and Modeling of Settling, Consolidation, and Suspension to Optimize Sediment Retention of Sediment Diversions for Coastal Restoration

NASA Astrophysics Data System (ADS)

Sha, X.; Xu, K.; Bentley, S. J.; Robichaux, P.

2016-02-01

Although many studies of sediment diversions have been conducted on the Mississippi Delta, relatively less attention has been paid to understanding sediment retention and basic cohesive sedimentation processes in receiving basins. Our research evaluates long-term (up to six months) sedimentation processes through various laboratory experiments, especially cohesive sediment settling, consolidation and resuspension and their impacts on sediment retention. Bulk sediment samples were collected from West Bay, near Head of Passes of the Mississippi Delta, and the Big Mar basin that receive water and sediment from the Caernarvon Diversion in the upper Breton Sound region of Louisiana, USA. A-230-cm tall settling column with nine sampling ports at 15 cm intervals was used to measure the consolidation for four initial sediment concentrations (10-120 kg m-3) with two salinities (1 ppt & 5 ppt). Samples of sediment slurry were taken from every port at different time intervals up to 15 days or longer (higher concentration needs longer time to consolidate) to record concentrations gravimetrically. A 200 cm long tube was connected to a 50 cm long core chamber to accumulate at least a 10 cm thick sediment column for erosion tests. A dual-core Gust Erosion Microcosm System was employed to measure time-series (0.5, 1, 2, 3, 4, 5, 6 months) erodibility at seven shear stress regimes (0.01-0.60 Pa). Our preliminary results show a significant decrease of erodibility with time and high concentration (120g/L). Salinity impacted on sediment behavior in consolidation experiments. Our study reveals that more enclosed receiving basins, intermittent openings of diversions, or reduced shear stress due to man-made structure all can potentially reduce cohesive sediment erosion in coastal Louisiana. Further results will be analyzed to determine the model constants. Consolidating rates and corresponding erosional changes will be determined to optimize sediment retention in coastal protection.

Origins of low resistivity in Al ion-implanted ZnO bulk single crystals

NASA Astrophysics Data System (ADS)

Oga, T.; Izawa, Y.; Kuriyama, K.; Kushida, K.; Kinomura, A.

2011-06-01

The origins of low resistivity in Al ion-implanted ZnO bulk single crystals are studied by combining Rutherford backscattering spectroscopy (RBS), nuclear reaction analysis (NRA), photoluminescence (PL), and Van der Pauw methods. The Al-ion implantation (peak concentration: 2.6 × 1020cm-3) into ZnO is performed using a multiple-step energy. The resistivity decreases from ˜104 Ω cm for un-implanted ZnO to 1.4 × 10-1 Ω cm for as-implanted, and reaches 6.0 × 10-4 Ω cm for samples annealed at 1000 °C. RBS and NRA measurements for as-implanted ZnO suggest the existence of the lattice displacement of Zn (Zni) and O (Oi), respectively. After annealing at 1000 °C, the Zni related defects remain and the Oi related defects disappear. The origin of the low resistivity in the as-implanted sample is attributed to the Zni (˜30 meV [Look et al., Phys. Rev. Lett. 82, 2552 (1999)]). In contrast, the origin of the low resistivity in the sample annealed at 1000 °C is assigned to both of the Zni related defects and the electrically activated Al donor. A new PL emission appears at around 3.32 eV after annealing at 1000 °C, suggesting electrically activated Al donors.

Interleukin-10 Contributes to Therapeutic Effect of Mesenchymal Stem Cells for Acute Liver Failure via Signal Transducer and Activator of Transcription 3 Signaling Pathway

PubMed Central

Ma, Hu-Cheng; Wang, Xin; Wu, Min-Na; Zhao, Xin; Yuan, Xian-Wen; Shi, Xiao-Lei

2016-01-01

Background: Mesenchymal stem cells (MSCs) transplantation has been proven to have therapeutic potential for acute liver failure (ALF). However, the mechanism remains controversial. Recently, modulation of inflammation by MSCs has been regarded as a crucial mechanism. The aim of the present study was to explore the soluble cytokines secreted by MSCs and their therapeutic effects in ALF. Methods: MSCs isolated from Sprague-Dawley rats were identified by fluorescence-activated cell sorting analysis. Conditioned medium derived from MSCs (MSCs-CM) was collected and analyzed by a cytokine microarray. MSCs and MSCs-CM were transplanted into rats with D-galactosamine-induced ALF. Liver function, survival rate, histology, and inflammatory factors were determined. Exogenous recombinant rat interleukin (IL)-10, anti-rat IL-10 antibody, and AG490 (signal transducer and activator of transcription 3 [STAT3] signaling pathway inhibitor) were administered to explore the therapeutic mechanism of MSCs-CM. Statistical analysis was performed with SPSS version 19.0, and all data were analyzed by the independent-sample t-test. Results: There are statistical differences of the survival curve between ALF+MSCs group and ALF+Dulbecco's modified Eagle's medium (DMEM) group, as well as ALF+MSCs-CM group and ALF+DMEM group (all P < 0.05). Serum alanine aminotransferase (ALT) level in the ALF+MSCs and ALF+MSCs-CM groups was lower than that in the ALF+DMEM group (865.53±52.80 vs. 1709.75±372.12 U/L and 964.72±414.59 vs. 1709.75±372.12 U/L, respectively, all P < 0.05); meanwhile, serum aspartate aminotransferase (AST) level in the ALF+MSCs and ALF+MSCs-CM groups was lower than that in the ALF+DMEM group (2440.83±511.94 vs. 4234.35±807.30 U/L and 2739.83±587.33 vs. 4234.35±807.30 U/L, respectively, all P < 0.05). Furthermore, MSCs or MSCs-CM treatment significantly reduced serum interferon-γ (IFN-γ), IL-1β, IL-6 levels and increased serum IL-10 level compared with DMEM (all P < 0.05). Proteome profile analysis of MSCs-CM indicated the presence of anti-inflammatory factors and IL-10 was the most distinct. Blocking of IL-10 confirmed the therapeutic significance of this cytokine. Phosphorylated STAT3 was upregulated after IL-10 infusion and inhibition of STAT3 by AG490 reversed the therapeutic effect of IL-10. Conclusions: The factors released by MSCs, especially IL-10, have the potential for therapeutic recovery of ALF, and the STAT3 signaling pathway may mediate the anti-inflammatory effect of IL-10. PMID:27064043

Backscatter correction factor for megavoltage photon beam

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hu, Yida; Zhu, Timothy C.

2011-10-15

Purpose: For routine clinical dosimetry of photon beams, it is often necessary to know the minimum thickness of backscatter phantom material to ensure that full backscatter condition exists. Methods: In case of insufficient backscatter thickness, one can determine the backscatter correction factor, BCF(s,d,t), defined as the ratio of absorbed dose measured on the central-axis of a phantom with backscatter thickness of t to that with full backscatter for square field size s and forward depth d. Measurements were performed in SAD geometry for 6 and 15 MV photon beams using a 0.125 cc thimble chamber for field sizes between 10more » x 10 and 30 x 30 cm at depths between d{sub max} (1.5 cm for 6 MV and 3 cm for 15 MV) and 20 cm. Results: A convolution method was used to calculate BCF using Monte-Carlo simulated point-spread kernels generated for clinical photon beams for energies between Co-60 and 24 MV. The convolution calculation agrees with the experimental measurements to within 0.8% with the same physical trend. The value of BCF deviates more from 1 for lower energies and larger field sizes. According to our convolution calculation, the minimum BCF occurs at forward depth d{sub max} and 40 x 40 cm field size, 0.970 for 6 MV and 0.983 for 15 MV. Conclusions: The authors concluded that backscatter thickness is 6.0 cm for 6 MV and 4.0 cm for 15 MV for field size up to 10 x 10 cm when BCF = 0.998. If 4 cm backscatter thickness is used, BCF is 0.997 and 0.983 for field size of 10 x 10 and 40 x 40 cm for 6 MV, and is 0.998 and 0.990 for 10 x 10 and 40 x 40 cm for 15 MV, respectively.« less

Effects of a Multidisciplinary Approach to Improve Volume of Diagnostic Material in CT-Guided Lung Biopsies

PubMed Central

Ferguson, Philip E.; Sales, Catherine M.; Hodges, Dalton C.; Sales, Elizabeth W.

2015-01-01

Background Recent publications have emphasized the importance of a multidisciplinary strategy for maximum conservation and utilization of lung biopsy material for advanced testing, which may determine therapy. This paper quantifies the effect of a multidisciplinary strategy implemented to optimize and increase tissue volume in CT-guided transthoracic needle core lung biopsies. The strategy was three-pronged: (1) once there was confidence diagnostic tissue had been obtained and if safe for the patient, additional biopsy passes were performed to further increase volume of biopsy material, (2) biopsy material was placed in multiple cassettes for processing, and (3) all tissue ribbons were conserved when cutting blocks in the histology laboratory. This study quantifies the effects of strategies #1 and #2. Design This retrospective analysis comparing CT-guided lung biopsies from 2007 and 2012 (before and after multidisciplinary approach implementation) was performed at a single institution. Patient medical records were reviewed and main variables analyzed include biopsy sample size, radiologist, number of blocks submitted, diagnosis, and complications. The biopsy sample size measured was considered to be directly proportional to tissue volume in the block. Results Biopsy sample size increased 2.5 fold with the average total biopsy sample size increasing from 1.0 cm (0.9–1.1 cm) in 2007 to 2.5 cm (2.3–2.8 cm) in 2012 (P<0.0001). The improvement was statistically significant for each individual radiologist. During the same time, the rate of pneumothorax requiring chest tube placement decreased from 15% to 7% (P = 0.065). No other major complications were identified. The proportion of tumor within the biopsy material was similar at 28% (23%–33%) and 35% (30%–40%) for 2007 and 2012, respectively. The number of cases with at least two blocks available for testing increased from 10.7% to 96.4% (P<0.0001). Conclusions The effect of this multidisciplinary strategy to CT-guided lung biopsies was effective in significantly increasing tissue volume and number of blocks available for advanced diagnostic testing. PMID:26479367

Water absorption lines, 931-961 nm - Selected intensities, N2-collision-broadening coefficients, self-broadening coefficients, and pressure shifts in air

NASA Technical Reports Server (NTRS)

Giver, L. P.; Gentry, B.; Schwemmer, G.; Wilkerson, T. D.

1982-01-01

Intensities were measured for 97 lines of H2O vapor between 932 and 961 nm. The lines were selected for their potential usefulness for remote laser measurements of H2O vapor in the earth's atmosphere. The spectra were obtained with several different H2O vapor abundances and N2 broadening gas pressures; the spectral resolution was 0.046/cm FWHM. Measured H2O line intensities range from 7 x 10 to the -25th to 7 x 10 to the -22nd/cm per (molecules/sq cm). H2O self-broadening coefficients were measured for 13 of these strongest lines; the mean value was 0.5/cm per atm. N2-collision-broadening coefficients were measured for 73 lines, and the average was 0.11 cm per atm HWHM. Pressure shifts in air were determined for a sample of six lines between 948 and 950 nm; these lines shift to lower frequency by an amount comparable to 0.1 of the collision-broadened widths measured in air or N2. The measured intensities of many lines of 300-000 band are much larger than expected from prior computations, in some cases by over an order of magnitude. Coriolis interactions with the stronger 201-000 band appear to be the primary cause of the enhancement of these line intensities.

Evidence for Ultra-Fast Outflows in Radio-Quiet AGNs. 2; Detailed Photoionization Modeling of Fe K-Shell Absorption Lines

NASA Technical Reports Server (NTRS)

Tombesi, Francesco; Clapp, M.; Reeves, J. N.; Palumbo, G. G. C.; Braito, V.; Dadina, M.

2011-01-01

X-ray absorption line spectroscopy has recently shown evidence for previously unknown Ultra-fast Outflows (UFOs) in radio-quiet AGNs. In the previous paper of this series we defined UFOs as those absorbers with an outflow velocity higher than 10,000km/s and assessed the statistical significance of the associated blue shifted FeK absorption lines in a large sample of 42 local radio-quiet AGNs observed with XMM-Newton. In the present paper we report a detailed curve of growth analysis and directly model the FeK absorbers with the Xstar photo-ionization code. We confirm that the frequency of sources in the radio-quiet sample showing UFOs is >35%. The outflow velocity distribution spans from \\sim10,000km/s (\\sim0.03c) up to \\siml00,000kmis (\\sim0.3c), with a peak and mean value of\\sim42,000km/s (\\sim0.14c). The ionization parameter is very high and in the range log\\xi 3-6 erg s/cm, with a mean value of log\\xi 4.2 erg s/cm. The associated column densities are also large, in the range N_H\\siml0(exp 22)-10(exp 24)/sq cm, with a mean value of N_H\\siml0(exp23)/sq cm. We discuss and estimate how selection effects, such as those related to the limited instrumental sensitivity at energies above 7keV, may hamper the detection of even higher velocities and higher ionization absorbers. We argue that, overall, these results point to the presence of extremely ionized and possibly almost Compton thick outflowing material in the innermost regions of AGNs. This also suggests that UFOs may potentially play a significant role in the expected cosmological feedback from AGNs and their study can provide important clues on the connection between accretion disks, winds and jets.

Soil bacterial and fungal community responses across a conservation reserve program chronosequence in Texas high plains region

USDA-ARS?s Scientific Manuscript database

We investigated changes in soil bacterial and fungal communities with increasing restoration time across a Conservation Reserve Program chronosequence (CRP) on fine sandy loam soils in the Texas high plains region. Soil samples (0-10cm) were collected in 2012 and 2014 from seven dryland croplands (0...

SU-F-J-149: Beam and Cryostat Scatter Characteristics of the Elekta MR-Linac

DOE Office of Scientific and Technical Information (OSTI.GOV)

Duglio, M; Towe, S; Roberts, D

2016-06-15

Purpose: The Elekta MR-Linac combines a digital linear accelerator system with a 1.5T Philips MRI machine. This study aimed to determine key characteristic information regarding the MR-Linac beam and in particular it evaluated the effect of the MR cryostat on the out of field scatter dose. Methods: Tissue phantom ratios, profiles and depth doses were acquired in plastic water with an IC-profiler or with an MR compatible water tank using multiple system configurations (Full (B0= 1.5T), Full (B0=0T) and No cryostat). Additionally, an in-house CAD based Monte Carlo code based on Penelope was used to provide comparative data. Results: Withmore » the cryostat in place and B0=0T, the measured TPR for the MR Linac system was 0.702, indicating an energy of around 7MV. Without the cryostat, the measured TPR was 0.669. For the Full (B0=0T) case, out of field dose at a depth of 10 cm in the isocentric plane, 5 cm from the field edge was 0.8%, 3.1% and 5.4% for 3×3 cm{sup 2}, 10×10 cm{sup 2} and 20×20 cm{sup 2} fields respectively.The out of field dose (averaged between 5 cm and 10 cm beyond the field edges) in the “with cryostat” case is 0.78% (absolute difference) higher than without the cryostat for clinically relevant field sizes (i.e. 10×10 cm{sup 2}) and comparable to measured conventional 6MV treatment beams at a depth of 10 cm (within 0.1% between 5 cm and 6 cm from field edge). At dose maximum and at 5 cm from the field edge, the “with cryostat” out of field scatter for a 10×10 cm{sup 2} field is 1.5% higher than “without cryostat', with a modest increase (0.9%) compared to Agility 6MV in the same conditions. Conclusion: The study has presented typical characteristics of the MR-Linac beam and determined that out of field dose is comparable to conventional treatment beams. All authors are employed by Elekta Ltd., who are developing an MR-Linac.« less

Effects of moisture content on coarse woody debris respiration in a tropical rainforest of Brunei Darussalam

NASA Astrophysics Data System (ADS)

Roh, Y.; Li, G.; Han, S. H.; Abu Salim, K.; Son, Y.

2017-12-01

Since coarse woody debris (CWD) respiration (Rcwd) has an important role in carbon (C) cycling in forest ecosystems, it is a significant parameter in an investigation of CWD decomposition rate. Rcwd is known as to be influenced not only by environmental factors but also by CWD properties (e.g., moisture content). This study investigated the effects of CWD moisture content on Rcwd in a lowland mixed Dipterocarp tropical rainforest of Brunei Darussalam. CWDs in the forest were selected and categorized into two decay classes (sound and partially decomposed), and three diameter classes (10-20 cm, 20-30 cm, more than 30 cm). Samplings of CWDs were conducted in February and October, 2016. The fresh weight and Rcwd of the samples were measured within 24 h of sampling. Rcwd measurements were conducted using a closed chamber system with a diffusion-type, non-dispersive infrared (NDIR) sensor. In February, the fresh weight and Rcwd of the samples were remeasured, after submerging them in the fresh water for 24, 48, and 72 h. The Rcwd increased significantly with moisture content in February (r2=0.25, p<0.01). During the study period from February to October, 2016, the mean value of Rcwd (±SE) decreased from 18.26 (3.45) to 14.92 (2.67) mg C kg-1 h-1 (p<0.05), although the moisture content did not change significantly (p>0.05). Rcwd was lowest in the largest diameter class (p<0.01), and not significantly different between the decay classes (p>0.05). On the basis of these results, the Rcwd in this site was in the range of Rcwd in previous studies conducted in other tropical rainforests. Rcwd increased with moisture content, however, the contribution of moisture content to changes in Rcwd might not be influential during the eight months study period.*Supported by research grants from the Korea Forest Service (2017044B10-1719-BB01).

SU-E-CAMPUS-T-05: Preliminary Results On a 2D Dosimetry System Based On the Optically Stimulated Luminescence of Al2O3

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ahmed, M; Eller, S; Yukihara, E

2014-06-15

Purpose: To develop a precise 2D dose mapping technique based on the optically stimulated luminescence (OSL) from Al{sub 2}O{sub 3} films for medical applications. Methods: A 2D laser scanning reader was developed using fast F{sup +}-center (lifetime of <7 ns) and slow F-center (lifetime of 35 ms) OSL emission from newly developed Al{sub 2}O{sub 3} films (Landauer Inc.). An algorithm was developed to correct images for both material and system properties. Since greater contribution of the F??-center emission in the recorded signal increases the readout efficiency and robustness of image corrections, Al{sub 2}O{sub 3}:C,Mg film samples are being investigated inmore » addition to Al{sub 2}O{sub 3}:C samples. Preliminary investigations include exposure of the films to a 6 MV photon beam at 10 cm depth in solid water phantom with an SSD of 100 cm, using a 10 cm × 10 cm flat field or a 4 cm × 4 cm field with a 60° wedge filter. Kodak EDR2 radiographic film and EBT2 Gafchromic film were also exposed for comparison. Results: The results indicate that the algorithm is able to correct images and calculate 2D dose. For the wedge field irradiation, the calculated dose at the center of the field was 0.9 Gy for Al{sub 2}O{sub 3}:C and 0.87 Gy for Al{sub 2}O{sub 3}:C,Mg, whereas, the delivered dose was 0.95 Gy. A good qualitative agreement of the dose profiles was obtained between the OSL films and EDR2 and EBT2 films. Laboratory tests using a beta source suggest that a large dynamic range (10{sup −2}−10{sup 2} Gy) can be achieved using this technique. Conclusion: A 2D dosimetry system and an in-house image correction algorithm were developed for 2D film dosimetry in medical applications. The system is in the preliminary stage of development, but the data demonstrates the feasibility of this approach. This work was supported by Landauer, Inc.« less

Brominated flame retardant (BFRs) and Dechlorane Plus (DP) in paired human serum and segmented hair.

PubMed

Qiao, Lin; Zheng, Xiao-Bo; Yan, Xiao; Wang, Mei-Huang; Zheng, Jing; Chen, She-Jun; Yang, Zhong-Yi; Mai, Bi-Xian

2018-01-01

Brominated flame retardants (BFRs) and Dechlorane Plus (DP) were measured in both human hair and paired serum samples from a cohort of university students in South China. Segmental analysis was conducted to explore gender difference and the relationships between the hair and serum. The concentrations of total PBDEs in the hair and serum samples were in a range of 0.28-34.1ng/g dry weight (dw) and 0.16-156ng/g lipid weight (lw), respectively. Concentrations of ∑DPs (sum of the syn-DP and anti-DP isomers) in all hair samples ranged from nd-5.45ng/g dry weight. Concentrations of most PBDEs and decabromodiphenylethane (DBDPE) in distal segments (5-10cm from the scalp) were higher than those in the proximal segments (0-5cm from the scalp) (t-test, p < 0.05), which could be due to the longer exposure time of distal segments. The proximal segments exhibited a unique congener profile, more close to that in the serum rather than the distal segments of hair. An obvious gender difference was found in the levels of ∑PBDEs using integrated hair samples, while the difference disappeared when considering alone the proximal segments of hair (0-5cm from scalp) for both genders. This paper provides supplement to the current knowledge on sources of BFRs and DPs in hair and declares the importance of segmental analysis. Copyright © 2017 Elsevier Inc. All rights reserved.

National validation study of a swab protocol for the recovery of Bacillus anthracis spores from surfaces.

PubMed

Hodges, Lisa R; Rose, Laura J; O'Connell, Heather; Arduino, Matthew J

2010-05-01

Twelve Laboratory Response Network (LRN) affiliated laboratories participated in a validation study of a macrofoam swab protocol for the recovery, detection, and quantification of viable B. anthracis (BA) Sterne spores from steel surfaces. CDC personnel inoculated steel coupons (26cm(2)) with 1-4 log(10) BA spores and recovered them by sampling with pre-moistened macrofoam swabs. Phase 1 (P1) of the study evaluated swabs containing BA only, while dust and background organisms were added to swabs in Phase 2 (P2) to mimic environmental conditions. Laboratories processed swabs and enumerated spores by culturing eluted swab suspensions and counting colonies with morphology consistent with BA. Processed swabs were placed in enrichment broth, incubated 24h, and cultured by streaking for isolation. Real-time PCR was performed on selected colonies from P2 samples to confirm the identity of BA. Mean percent recovery (%R) of spores from the surface ranged from 15.8 to 31.0% (P1) and from 27.9 to 55.0% (P2). The highest mean percent recovery was 31.0% (sd 10.9%) for P1 (4 log(10) inoculum) and 55.0% (sd 27.6%) for P2 (1 log(10) inoculum). The overall %R was higher for P2 (44.6%) than P1 (24.1%), but the overall reproducibility (between-lab variability) was lower in P2 than in P1 (25.0 vs 16.5%CV, respectively). The overall precision (within-lab variability) was close to identical for P1 and P2 (44.0 and 44.1, respectively), but varied greatly between inoculum levels. The protocol demonstrated linearity in %R over the three inoculum levels and is able to detect between 26 and 5x10(6)spores/26cm(2). Sensitivity as determined by culture was >98.3% for both phases and all inocula, suggesting that the culture method maintains sensitivity in the presence of contaminants. The enrichment broth method alone was less sensitive for sampled swabs (66.4%) during P2, suggesting that the presence of background organisms inhibited growth or isolation of BA from the broth. The addition of real-time PCR testing to the assay increased specificity from >85.4% to >95.0% in P2. Although the precision was low at the 1 log(10) inoculum level in both phases (59.0 and 50.2%), this swab processing protocol, was sensitive, specific, precise, and reproducible at 2-4 log(10)/26cm(2) spore concentrations. Published by Elsevier B.V.

Globally Convergent Methods for Solving Coefficient Inverse Problems for Time Dependent Maxwell Equations

DTIC Science & Technology

2014-08-19

geode (heterogeneous): Rock two spherical layers and air inside 13 Blind A piece of rock Rock 14 Blind A plastic bottle filled with coffee grounds... Coffee grounds 15 Blind A ceramic mug Ceramic 16 Blind A cylinder and a block at 3 cm separation Metal/Metal 17 Blind An aluminum can and a block Metal...2.5 cm 1.0 1.52 1.31 (outer) (two layers) 1.25 (inner) 1.28 (average) 13 Rock 2.0 cm 2.3 cm 1.0 1.34 1.34 14 Coffee grounds 2.0 cm 2.5 cm 1.0 1.46

Incidence of clinical mastitis and distribution of pathogens on large Chinese dairy farms.

PubMed

Gao, Jian; Barkema, Herman W; Zhang, Limei; Liu, Gang; Deng, Zhaoju; Cai, Lingjie; Shan, Ruixue; Zhang, Shiyao; Zou, Jiaqi; Kastelic, John P; Han, Bo

2017-06-01

Knowledge of the incidence of clinical mastitis (CM) and the distribution of pathogens involved is essential for development of prevention and control programs as well as treatment protocols. No country-wide study on the incidence of CM and the distribution of pathogens involved has been conducted in China. Core objectives of this study were, therefore, to determine the cumulative incidence of CM and the distribution of pathogens causing CM on large Chinese (>500 cows) dairy farms. In addition, associations between the distribution of CM pathogens and bedding materials and seasonal factors were also investigated. Bacterial culture was done on a total of 3,288 CM quarter milk samples from 161 dairy herds (located in 21 provinces) between March 2014 and September 2016. Additional data, including geographical region of herds, herd size, bedding types, and number of CM cases during the last month, were also recorded. Mean cumulative incidence of CM was 3.3 cases per 100 cows per month (range = 1.7 to 8.1). The most frequently isolated pathogens were Escherichia coli (14.4%), Klebsiella spp. (13.0%), coagulase-negative staphylococci (11.3%), Streptococcus dysgalactiae (10.5%), and Staphylococcus aureus (10.2%). Streptococcus agalactiae was isolated from 2.8% of CM samples, whereas Streptococcus uberis were isolated from 2.1% of samples, and 15.8% of 3,288 samples were culture-negative. Coagulase-negative staphylococci, E. coli, and other Enterobacter spp. were more frequently isolated in the northwest than the northeast or south of China. Streptococcus dysgalactiae, other streptococci, and Strep. agalactiae were more frequently isolated in winter (October-March), whereas E. coli and Klebsiella spp. were mostly isolated in summer (April-September). Streptococcus dysgalactiae was more often isolated from CM cases of herds using sand bedding, whereas Klebsiella spp. and other streptococci were more common in herds using organic bedding. The incidence of CM and distribution of pathogens differed among herds and better mastitis management is needed. Furthermore, geography, bedding materials, and season should be included when designing mastitis control and prevention schemes for Chinese dairies. Copyright © 2017 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Collision-induced absorption in the region of the ν2 + ν3 band of carbon dioxide

NASA Astrophysics Data System (ADS)

Baranov, Yu. I.

2018-03-01

The IR absorption spectra of pure carbon dioxide in the region of the forbidden ν2 + ν3 vibrational transition at 3004 cm-1 have been recorded using a Fourier-transform spectrometer. A multipass-optical cell with the path length of 100 m was used in the study. The data were taken at room temperature of 294.8 K with a resolution of 0.02 cm-1 over the spectral region 2500-3500 cm-1. A sample pressures varied from 207 to 463 kPa (2.04-4.57 atm). The measured binary absorption coefficients provide the band integrated intensity value of (2.39 ± 0.04) ∗ 10-4 cm-2 amagat-2. The result is compared with those from previous works. The observed band profile features are discussed.

[Study on soil enzyme activities and microbial biomass carbon in greenland irrigated with reclaimed water].

PubMed

Pan, Neng; Hou, Zhen-An; Chen, Wei-Ping; Jiao, Wen-Tao; Peng, Chi; Liu, Wen

2012-12-01

The physicochemical properties of soils might be changed under the long-term reclaimed water irrigation. Its effects on soil biological activities have received great attentions. We collected surface soil samples from urban green spaces and suburban farmlands of Beijing. Soil microbial biomass carbon (SMBC), five types of soil enzyme activities (urease, alkaline phosphatase, invertase, dehydrogenase and catalase) and physicochemical indicators in soils were measured subsequently. SMBC and enzyme activities from green land soils irrigated with reclaimed water were higher than that of control treatments using drinking water, but the difference is not significant in farmland. The SMBC increased by 60.1% and 14.2% than those control treatments in 0-20 cm soil layer of green land and farmland, respectively. Compared with their respective controls, the activities of enzymes in 0-20 cm soil layer of green land and farmland were enhanced by an average of 36.7% and 7.4%, respectively. Investigation of SMBC and enzyme activities decreased with increasing of soil depth. Significantly difference was found between 0-10 cm and 10-20 cm soil layer in green land. Soil biological activities were improved with long-term reclaimed water irrigation in Beijing.

Solar energy dryer kinetics using flat-plate finned collector and forced convection for potato drying

NASA Astrophysics Data System (ADS)

Batubara, Fatimah; Misran, Erni; Dina, Sari Farah; Heppy

2017-06-01

Research on potato drying using the indirect solar dryer with flat-plate finned collector and forced convection has been done. The research was conducted at the outdoor field of Laboratory of Institute for Research and Standardization of Industry on June 14th-23rd, 2016 from 9:00 am to 4:00 pm. This research aims to obtain the drying kinetics model of potato (Solanumtuberosum L.) using an indirect solar dryer's (ISD) with flat plate-finned collector and forced convection. The result will be compared to the open sun drying (OSD) method. Weather conditions during the drying process took place as follows; surrounding air temperature was in the range 27 to 34.7 °C, relative humidity (RH) 29.5 to 61.0% and the intensity of solar radiation 105.6 to 863.1 Watt/m2. The dried potato thicknesses were 1.0 cm, 1.5 cm and 2.0 cm, with the average initial water content of 76.46%. The average temperature in the collector chamber ranged from 42.2 to 57.4 °C and the drying chamber was at 46.2 °C. The best drying result was obtained from a sample size of 1 cm thickness using the IDS method with an average drying rate of 0.018 kg H2O per kg dry-weight.hour and the water content was constant at 5.02% in 21 hours of drying time. The most suitable kinetics model is Page model, equation MR = exp (-0.049 t1,336) for 1.0 cm thickness, exp (-0.066 t1,222) for 1.5 cm thickness and exp (-0.049 t1,221) for 2.0 cm thickness. The quality of potato drying using ISD method is better than using OSD which can be seen from the color produced.

Real-time estimation of BDS/GPS high-rate satellite clock offsets using sequential least squares

NASA Astrophysics Data System (ADS)

Fu, Wenju; Yang, Yuanxi; Zhang, Qin; Huang, Guanwen

2018-07-01

The real-time precise satellite clock product is one of key prerequisites for real-time Precise Point Positioning (PPP). The accuracy of the 24-hour predicted satellite clock product with 15 min sampling interval and an update of 6 h provided by the International GNSS Service (IGS) is only 3 ns, which could not meet the needs of all real-time PPP applications. The real-time estimation of high-rate satellite clock offsets is an efficient method for improving the accuracy. In this paper, the sequential least squares method to estimate real-time satellite clock offsets with high sample rate is proposed to improve the computational speed by applying an optimized sparse matrix operation to compute the normal equation and using special measures to take full advantage of modern computer power. The method is first applied to BeiDou Navigation Satellite System (BDS) and provides real-time estimation with a 1 s sample rate. The results show that the amount of time taken to process a single epoch is about 0.12 s using 28 stations. The Standard Deviation (STD) and Root Mean Square (RMS) of the real-time estimated BDS satellite clock offsets are 0.17 ns and 0.44 ns respectively when compared to German Research Center for Geosciences (GFZ) final clock products. The positioning performance of the real-time estimated satellite clock offsets is evaluated. The RMSs of the real-time BDS kinematic PPP in east, north, and vertical components are 7.6 cm, 6.4 cm and 19.6 cm respectively. The method is also applied to Global Positioning System (GPS) with a 10 s sample rate and the computational time of most epochs is less than 1.5 s with 75 stations. The STD and RMS of the real-time estimated GPS satellite clocks are 0.11 ns and 0.27 ns, respectively. The accuracies of 5.6 cm, 2.6 cm and 7.9 cm in east, north, and vertical components are achieved for the real-time GPS kinematic PPP.

Crystal Growth and Characterization of CdTe Grown by Vertical Gradient Freeze

NASA Technical Reports Server (NTRS)

Su, Ching-Hua; Lehoczky, S. L.; Raghothamachar, B.; Dudley, M.

2007-01-01

In this study, crystals of CdTe were grown from melts by the unseeded vertical gradient freeze method. The quality of grown crystal were studied by various characterization techniques including Synchrotron White Beam X-ray Topography (SWBXT), chemical analysis by glow discharge mass spectroscopy (GDMS), low temperature photoluminescence (PL), and Hall measurements. The SWBXT images from various angles show nearly strain-free grains, grains with inhomogeneous strains, as well as twinning nucleated in the shoulder region of the boule. The GDMS chemical analysis shows the contamination of Ga at a level of 3900 ppb, atomic. The low temperature PL measurement exhibits the characteristic emissions of a Ga-doped sample. The Hall measurements show a resistivity of 1 x l0(exp 7) ohm-cm at room temperature to 3 x 10(exp 9) ohm-cm at 78K with the respective hole and electron concentration of 1.7 x 10(exp 9) cm(exp -3) and 3.9 x 10(exp 7) cm(exp -3) at room temperature.

The Effect of Carbon and Boron on the Friction Behavior of Ti-Implanted 52100 Bearing Steel at Low Sliding Speeds

DTIC Science & Technology

1982-05-01

process, titanium chlorides are produced by passing chlorine gas through a fine titanium powder contained in a graphite chamber. At the high source...CO was used for a carbon source; the boron source was boron trifluoride . The 52100 samples were disks 0.95 cm in diameter and 0.3 cm thick. During...eV modulation amplitude. The ion gun 1w operated in an Ar atmosphere (5 x 10-5 torr) with a rastered beam of 2 keY Ar+ ions at densities ranging from

Respiratory mechanics and results of cytologic examination of bronchoalveolar lavage fluid in healthy adult alpacas.

PubMed

Pacheco, Ana P; Bedenice, Daniela; Mazan, Melissa R; Hoffman, Andrew M

2012-01-01

To evaluate respiratory mechanical function and bronchoalveolar lavage (BAL) cytologic results in healthy alpacas. 16 client-owned adult alpacas. Measurements of pulmonary function were performed, including functional residual capacity (FRC) via helium dilution, respiratory system resistance via forced oscillatory technique (FOT), and assessment of breathing pattern by use of respiratory inductive plethysmography (RIP) in standing and sternally recumbent alpacas. Bronchoalveolar lavage was performed orotracheally during short-term anesthesia. Mean ± SD measurements of respiratory function were obtained in standing alpacas for FRC (3.19 ± 0.53 L), tidal volume (0.8 ± 0.13 L), and respiratory system resistance at 1 Hz (2.70 ± 0.88 cm H(2)O/L/s), 2 Hz (2.98 ± 0.70 cm H(2)O/L/s), 3 Hz (3.14 ± 0.77 cm H(2)O/L/s), 5 Hz (3.45 ± 0.91 cm H(2)O/L/s), and 7 Hz (3.84 ± 0.93 cm H(2)O/L/s). Mean phase angle, as a measurement of thoracoabdominal asynchrony, was 19.59 ± 10.06°, and mean difference between nasal and plethysmographic flow measurements was 0.18 ± 0.07 L/s. Tidal volume, peak inspiratory flow, and peak expiratory flow were significantly higher in sternally recumbent alpacas than in standing alpacas. Cytologic examination of BAL fluid revealed 58.52 ± 12.36% alveolar macrophages, 30.53 ± 13.78% lymphocytes, 10.95 ± 9.29% neutrophils, 0% mast cells, and several ciliated epithelial cells. Pulmonary function testing was tolerated well in nonsedated untrained alpacas. Bronchoalveolar lavage in alpacas yielded samples with adequate cellularity that had a greater abundance of neutrophils than has been reported in horses.

Experiment 13: The Study of Dopant Segregation Behavior During the Growth of GaAs in Microgravity on USML-2

NASA Technical Reports Server (NTRS)

Matthiesen, David H.; Kaforey, Monica L.; Bly, J. M.; Chait, Arnon; Kafalas, James; Carlson, Douglas

1998-01-01

An investigation into the segregation behavior of selenium doped gallium arsenide (Se/GaAs) during directional solidification in the microgravity environment was conducted using the Crystal Growth Furnace (CGF) aboard the second United States Microgravity Laboratory (USML-2). Two crystals were successfully processed on USML-2, which lasted from October 20 to November 7, 1995. The first sample was processed for 67 hours, 45 minutes (MET 5/04:53:45-8/00:23:50) and included 19 hours of growth at 0.5 microns/sec which yielded 3.42 cm of sample length, and 5 hours of growth at 1.5 microns/sec which yielded 2.7 cm of sample. During the second experiment, the furnace temperature was adjusted to move the melt-solid interface position towards the hot end of the furnace. The second sample was processed for 50 hours, 10 minutes (MET 8/18:48:49-10/21:58:54) and included 11 hours of growth at 0.5 microns/sec which yielded 1.98 cm of sample, and 1 hour, 25 minutes of growth at 5.0 microns/sec which yielded 2.6 cm of sample. This sample provides an order of magnitude change in growth rate and reproduces one of the growth rates used during USML-1. In contrast to the results from USML-1, no voids were present in either crystal grown on USML-2. The absence of voids in either sample indicates that growth rate changes alone were not responsible for the formation of voids found in the crystals grown on USML-1. Sections of the ground-based and flight crystals grown on USML-2 were cut and polished. All of the interface demarcation lines expected from the current pulse interface demarcation (CPID) system have been identified. These measurements have been analyzed for interface positions, interface shapes, and growth rates. Using a newly developed technique, based on experimental and numerical results, the seeding interface reproducibility from run to run was <= 2.5 mm. The seeding interface position could be controllably moved, with respect to the furnace zones, by adjusting the control set points of the heating zones. The interface shapes flattened slightly as the interface position moved closer to the hot zone but was always an unfavorable concave into the solid shape. The growth rate was found to equal the furnace translation rate, after a 2 -hour transient, for growth rates <= 1.0 microns/sec. Segregation measurements for the ground-based crystals are indicative of complete mixing behavior, as expected. Segregation measurements of the flight crystals are still in progress.

False-Negative Rate and Recovery Efficiency Performance of a Validated Sponge Wipe Sampling Method

PubMed Central

Piepel, Greg F.; Boucher, Raymond; Tezak, Matt; Amidan, Brett G.; Einfeld, Wayne

2012-01-01

Recovery of spores from environmental surfaces varies due to sampling and analysis methods, spore size and characteristics, surface materials, and environmental conditions. Tests were performed to evaluate a new, validated sponge wipe method using Bacillus atrophaeus spores. Testing evaluated the effects of spore concentration and surface material on recovery efficiency (RE), false-negative rate (FNR), limit of detection (LOD), and their uncertainties. Ceramic tile and stainless steel had the highest mean RE values (48.9 and 48.1%, respectively). Faux leather, vinyl tile, and painted wood had mean RE values of 30.3, 25.6, and 25.5, respectively, while plastic had the lowest mean RE (9.8%). Results show roughly linear dependences of RE and FNR on surface roughness, with smoother surfaces resulting in higher mean REs and lower FNRs. REs were not influenced by the low spore concentrations tested (3.10 × 10−3 to 1.86 CFU/cm2). Stainless steel had the lowest mean FNR (0.123), and plastic had the highest mean FNR (0.479). The LOD90 (≥1 CFU detected 90% of the time) varied with surface material, from 0.015 CFU/cm2 on stainless steel up to 0.039 on plastic. It may be possible to improve sampling results by considering surface roughness in selecting sampling locations and interpreting spore recovery data. Further, FNR values (calculated as a function of concentration and surface material) can be used presampling to calculate the numbers of samples for statistical sampling plans with desired performance and postsampling to calculate the confidence in characterization and clearance decisions. PMID:22138998

{sup 40}K, {sup 115}Cs and {sup 226}Ra Soil and Plant Content in Seminatural Grasslands of Central Argentina

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ayub, J. Juri; Velasco, R. H.; Rizzotto, M.

2008-08-07

Activity concentrations of {sup 40}K, {sup 226}Ra and {sup 137}Cs have been analyzed in soil and plant samples, collected in permanent grassland in central Argentina. Two near areas (A1 and A2) under field conditions with soil undisturbed at least in the last four decades were selected. For each of the three studied radionuclides we do not find differences in the inventories between both areas. The inventories range from 143 kBq m{sup -2} to 197 kBq m{sup -2} for {sup 40}K and from 13 kBq m{sup -2} to 18 kBq m{sup -2} for {sup 226}Ra. The vertical distributions of {sup 40}Kmore » and {sup 226}Ra are uniform through de soil profile. For {sup 137}Cs the inventories range from 0.33 kBq m{sup -2} to 0.73 kBq m{sup -2}. In spite of {sup 137}Cs inventories are similar in both areas the distribution through vertical profile is different. {sup 137}Cs activity concentration has a maximum for layers 5-10 cm depth in A1 and 10-15 cm depth in A2. For deeper layers both areas show similar activity concentrations. The diffusion coefficient (D{sub s}) and convection velocity (v{sub s}) are estimated with a convection-diffusion model. D{sub s} values are in the range reported in the bibliography, while v{sub s} values are one order of magnitude higher. After 40 years most {sup 137}Cs fallout is still in the layer 10-15 cm depth. The great penetration of {sup 137}Cs (25 cm) in these soils may be the result of a high sand and low fine materials content. {sup 137}Cs and {sup 226}Ra were not detected in grass samples. Activity concentration of {sup 40}K in vegetal samples ranges from 116 Bq kg{sup -1} to 613 Bq kg{sup -1}. The TF values obtained for {sup 40}K show a lognormal distribution and ranges from 0.05 to 0.42.« less

Carbohydrates and thermal analysis reflects changes in soil organic matter stability after forest expansion on abandoned grassland

NASA Astrophysics Data System (ADS)

Guidi, Claudia; Vesterdal, Lars; Cannella, David; Leifeld, Jens; Gianelle, Damiano; Rodeghiero, Mirco

2014-05-01

Grassland abandonment, followed by progressive forest expansion, is the dominant land-use change in the Southern Alps, Europe. Land-use change can affect not only the amount of organic matter (OM) in soil but also its composition and stability. Our objective was to investigate changes in organic matter properties after forest expansion on abandoned grasslands, combining analysis of carbohydrates, indicative of labile OM compounds with prevalent plant or microbial origin, with thermal analysis. Thermal analysis was used as a rapid assessment method for the characterization of SOM stability. A land-use gradient was investigated in four land-use types in the subalpine area of Trentino region, Italy: i) managed grassland, mown and fertilized for the past 100 years; ii) grassland abandoned since 10 years, with sparse shrubs and Picea abies saplings; iii) early-stage forest, dominated by P. abies and established on a grassland abandoned around 1970; iv) old forest, dominated by Fagus sylvatica and P. abies. Mineral soil was sampled at three subplots in each land use type with eight soil cores, which were subsequently pooled by depth (0-5 cm, 5-10 cm, 10-20 cm). Sugars were extracted from bulk soil samples through acid hydrolysis with H2SO4 (0.5 M). The analytical composition of sugar monomers was performed with HPAEC technology (Dionex ICS5000), equipped with PAD-detection. Thermal stability was assessed with a differential scanning calorimeter DSC100, heating soil samples up to 600°C at a heating rate of 10°C min-1 in synthetic air. Peak height (W g OC-1) of 1st DSC exotherm, dominated by burning of labile OM compounds, was used as thermal stability index. In the abandoned grassland, carbohydrates compounds accounted for a greater proportion of soil OC than in other land use types. Microbially derived sugars, as rhamnose and galactose, were more abundant in managed and abandoned grasslands compared with early-stage and old forest. The amount of thermally labile sugars, estimated as the peak height of the 1st exotherm, was higher in the abandoned grassland compared with managed grassland and old forest in 0-5 cm depth. Moreover, thermally labile compounds were higher in early-stage than in old forest in 0-5 cm depth. A highly significant correlation was found between thermally labile compounds and carbohydrate content in soil (P = 0.008, r = 0.725). The obtained results suggest that both thermally-labile compounds and carbohydrates are more abundant soon after grassland abandonment, which can lead to lower OM stability. The combination of chemical and thermal analysis of OM can thus provide useful insights on organic matter composition and stability.

Combined deep sampling and mass-based approaches to assess soil carbon and nitrogen losses due to land-use changes in karst area of southwestern China

NASA Astrophysics Data System (ADS)

Hu, Yecui; Du, Zhangliu; Wang, Qibing; Li, Guichun

2016-07-01

The conversion of natural vegetation to human-managed ecosystems, especially the agricultural systems, may decrease soil organic carbon (SOC) and total nitrogen (TN) stocks. The objective of present study was to assess SOC and TN stocks losses by combining deep sampling with mass-based calculations upon land-use changes in a typical karst area of southwestern China. We quantified the changes from native forest to grassland, secondary shrub, eucalyptus plantation, sugarcane and corn fields (both defined as croplands), on the SOC and TN stocks down to 100 cm depth using fixed-depth (FD) and equivalent soil mass (ESM) approaches. The results showed that converting forest to cropland and other types significantly led to SOC and TN losses, but the extent depended on both sampling depths and calculation methods selected (i.e., FD or ESM). On average, the shifting from native forest to cropland led to SOC losses by 19.1, 25.1, 30.6, 36.8 and 37.9 % for the soil depths of 0-10, 0-20, 0-40, 0-60 and 0-100 cm, respectively, which highlighted that shallow sampling underestimated SOC losses. Moreover, the FD method underestimated SOC and TN losses for the upper 40 cm layer, but overestimated the losses in the deeper layers. We suggest that the ESM together with deep sampling should be encouraged to detect the differences in SOC stocks. In conclusion, the conversion of forest to managed systems, in particular croplands significantly decreased in SOC and TN stocks, although the effect magnitude to some extent depended on sampling depth and calculation approach selected.

Direct nano-patterning of graphene with helium ion beams

NASA Astrophysics Data System (ADS)

Naitou, Y.; Iijima, T.; Ogawa, S.

2015-01-01

Helium ion microscopy (HIM) was used for direct nano-patterning of single-layer graphene (SLG) on SiO2/Si substrates. This technique involves irradiation of the sample with accelerated helium ions (He+). Doses of 2.0 × 1016 He+ cm-2 from a 30 kV beam induced a metal-insulator transition in the SLG. The resolution of HIM patterning on SLG was investigated by fabricating nanoribbons and nanostructures. Analysis of scanning capacitance microscopy measurements revealed that the spatial resolution of HIM patterning depended on the dosage of He+ in a non-monotonic fashion. Increasing the dose from 2.0 × 1016 to 5.0 × 1016 He+ cm-2 improved the spatial resolution to several tens of nanometers. However, doses greater than 1.0 × 1017 He+ cm-2 degraded the patterning characteristics. Direct patterning using HIM is a versatile approach to graphene fabrication and can be applied to graphene-based devices.

X-ray evidence for ultra-fast outflows in Seyfert galaxies

NASA Astrophysics Data System (ADS)

Tombesi, Francesco; Braito, Valentina; Reeves, James; Cappi, Massimo; Dadina, Mauro

2012-07-01

X-ray evidence for massive, highly ionized, ultra-fast outflows (UFOs) has been recently reported in a number of AGNs through the detection of blue-shifted Fe XXV/XXVI absorption lines. We present the results of a comprehensive spectral analysis of a large sample of 42 local Seyferts observed with XMM-Newton. Similar results are also obtained from a Suzaku analysis of 5 radio galaxies. We find that UFOs are common phenomena, being present in >40% of the sources. Their outflow velocity distribution is in the range ˜0.03--0.3c, with mean value of ˜0.14c. The ionization parameter is very high, in the range logξ˜3--6 erg~s^{-1}~cm, and the associated column densities are also large, in the range ˜10^{22}--10^{24} cm^{-2}. Their location is constrained at ˜0.0003--0.03pc (˜10^2--10^4 r_s) from the central black hole, consistent with what is expected for accretion disk winds/outflows. The mass outflow rates are in the interval ˜0.01--1M_{⊙}~yr^{-1}. The associated mechanical power is also high, in the range ˜10^{43}--10^{45} erg/s, which indicates that UFOs are capable to provide a significant contribution to the AGN cosmological feedback.

Ketorolac for Pain Control With Intrauterine Device Placement: A Randomized Controlled Trial

PubMed Central

Ngo, Lynn L.; Ward, Kristy K.; Mody, Sheila K.

2015-01-01

Objective To evaluate intramuscular ketorolac compared to placebo saline injection for pain control with intrauterine device (IUD) placement. Methods We conducted a randomized, double-blind, placebo controlled trial between July 2012 and March 2014. Patients received ketorolac 30mg or placebo saline intramuscular injection 30 minutes prior to IUD placement. The primary outcome was pain with IUD placement on a 10cm visual analog scale (VAS). Sample size was calculated to provide 80% power to show a 2.0cm difference (α=0.05) in the primary outcome. Secondary outcomes included pain with study drug injection, speculum insertion, tenaculum placement, uterine sounding, and at 5 and 15 minutes after IUD placement. Results A total of 67 women participated in the study, 33 in the ketorolac arm and 34 in the placebo arm. There were no differences in baseline demographics including age, BMI, and race. There were no differences in median pain scores for IUD placement in the placebo versus ketorolac groups (5.2cm vs 3.6cm, p=0.99). There was a decrease in median pain scores at 5 minutes (2.2cm vs 0.3cm, p=<0.001) and 15 minutes (1.6cm vs 0.1cm, p=<0.001) after IUD placement but no difference for all other time points. Nulliparous participants (n=16, 8 per arm) had a decrease in pain scores with IUD placement (8.1cm vs 5.4cm, p=0.02). In this study, 22% of participants in the placebo group and 18% in the ketorolac group reported injection pain was as painful as IUD placement. Conclusions Ketorolac does not reduce pain with IUD placement but does reduce pain at 5 and 15 minutes after placement. PMID:26241253

Low resistance ohmic contacts to n-GaN and n-AlGaN using NiAl

NASA Astrophysics Data System (ADS)

Ingerly, D. B.; Chen, Y.; William, R. S.; Takeuchi, T.; Chang, Y. A.

2000-07-01

The intermetallic compound NiAl (50:50 at. %) has been shown to be a low-resistance ohmic contact to n-GaN and n-AlGaN. NiAl contacts on n-GaN (n=2.5×1017cm-3) had a specific contact resistance of 9.4×10-6 Ω cm2 upon annealing at 850 °C for 5 min. NiAl contacts annealed at 900 °C for 5 min in n-Al0.12Ga0.88N (n=2.4×1018cm-3) and n-Al0.18Ga0.82N (n=2.7×1018cm-3) had specific contact resistances of 2.1×10-5 Ω cm2 and 4.7×10-5 Ω cm2, respectively. Additionally, these contacts were subjected to long-term annealing at 600 °C for 100 h. On n-GaN, the contact specific contact resistance degraded from 9.4×10-6 Ω cm2 to 5.3×10-5 Ω cm2 after the long-term anneal. Contacts to n-Al0.18Ga0.82N showed only slight degradation with a change in contact resistance, from 4.7×10-5 Ω cm2 to 9.2×10-5 Ω cm2. These results demonstrate the NiAl has great promise as a stable, low-resistance contact, particularly to n-AlGaN used in high-temperature applications.

Microbially-mediated carbon fluxes vary with landscape position in two erodible, intensively managed agricultural landscapes

NASA Astrophysics Data System (ADS)

Fine, A.; Wilson, C. G.; Papanicolaou, T.; Schaeffer, S. M.

2017-12-01

The balance between loss of C to the atmosphere, and the accumulation of soil organic matter is directly controlled by soil microorganisms. A key driver of microbial activity is soil moisture, but it is unclear how microbial C cycling responds to spatiotemporal shifts in hydrological conditions across a heterogeneous, dynamic landscape. We explored the relationship between soil wetness and biogeochemical cycling along landscape positions in two sloping fields of the Intensively Managed Landscape Critical Zone Observatory (IML-CZO) in Iowa, USA. Soils were collected (0-5 cm, 5-10 cm) from four positions (crest, shoulder, backslope, toeslope) along three transects identified as primary flow paths for runoff and sediment. Samples were incubated for 7 days and analyzed pre- and post-incubation for extractable dissolved organic C (DOC), microbial biomass C (MBC), microbial respiration (C-resp), and inorganic N. At both sites, field moisture, MBC, and CUE 0-5 cm increased from summit to toeslope, whereas CUE 5-10 cm decreased. The steeper and drier of the two fields (field 1) showed corresponding increases in C-resp and NO3, but decreases in DOC, moving downslope; the opposite trends were observed in the less erodible, wetter field 2. Comparing the two toeslopes (0-5 cm), field 2 had a larger labile C (DOC + MBC) pool (3.1 mg C g-1 dry soil) than field 1 (2.7 mg g-1 dry soil), but C-resp of field 1 was lower (53 and 42 ug g-1 dry soil for fields 1 and 2, respectively). No differences in MBC between depths were observed in field 1, but in field 2, MBC 5-10 cm (0.6 and 0.7 mg g-1 dry soil at crest and toeslope, respectively) was always less than MBC 0-5 cm (0.9 mg g-1 dry soil). Our findings indicate that wet, poorly drained soil conditions (such as those in lower landscape positions and at depth) decrease microbial activity and allow DOC to accumulate. Despite the relatively enhanced depositional environment of field 1, the low levels of DOC and high C-resp and MBC indicate more suitable conditions for aerobic respiration.

Self-organizing nanodot structures on InP surfaces evolving under low-energy ion irradiation: analysis of morphology and composition.

PubMed

Radny, Tobias; Gnaser, Hubert

2014-01-01

Surfaces of InP were bombarded by 1.9 keV Ar(+) ions under normal incidence. The total accumulated ion fluence Φ the samples were exposed to was varied from 1 × 10(17) cm(-2) to 3 × 10(18) cm(-2), and ion fluxes f of (0.4 - 2) × 10(14) cm(-2) s(-1) were used. The surface morphology resulting from these ion irradiations was examined by atomic force microscopy (AFM). Generally, nanodot structures are formed on the surface; their dimensions (diameter, height and separation), however, were found to depend critically on the specific bombardment conditions. As a function of ion fluence, the mean radius r, height h, and spacing l of the dots can be fitted by power-law dependences: r ∝ Φ(0.40), h ∝ Φ(0.48), and l ∝ Φ(0.19). In terms of ion flux, there appears to exist a distinct threshold: below f ~ (1.3 ± 0.2) × 10(14) cm(-2) s(-1), no ordering of the dots exists and their size is comparatively small; above that value of f, the height and radius of the dots becomes substantially larger (h ~ 40 nm and r ~ 50 nm). This finding possibly indicates that surface diffusion processes could be important. In order to determine possible local compositional changes in these nanostructures induced by ion impact, selected samples were prepared for atom probe tomography (APT). The results indicate that APT can provide analytical information on the composition of individual InP nanodots. By means of 3D APT data, the surface region of such nanodots evolving under ion bombardment could be examined with atomic spatial resolution. At the InP surface, the values of the In/P concentration ratio are distinctly higher over a distance of approximately 1 nm and amount to 1.3 to 1.7.

Thermal electron attachment to chlorinated alkenes in the gas phase

NASA Astrophysics Data System (ADS)

Wnorowski, K.; Wnorowska, J.; Michalczuk, B.; Jówko, A.; Barszczewska, W.

2017-01-01

This paper reports the measurements of the rate coefficients and the activation energies of the electron capture processes with various chlorinated alkenes. The electron attachment processes in the mixtures of chlorinated alkenes with carbon dioxide have been investigated using a Pulsed Townsend technique. This study has been performed in the temperature range (298-378) K. The obtained rate coefficients more or less depended on temperature in accordance to Arrhenius equation. The activation energies (Ea's) were determined from the fit to the experimental data points with function ln(k) = ln(A) - Ea/kBT. The rate coefficients at 298 K were equal to 1.0 × 10-10 cm3 s-1, 2.2 × 10-11 cm3 s-1, 1.6 × 10-9 cm3 s-1, 4.4 × 10-8 cm3 s-1, 2.9 × 10-12 cm3 s-1 and 7.3 × 10-12 cm3 s-1 and activation energies were: 0.27 eV, 0.26 eV, 0.25 eV, 0.21 eV, 0.55 eV and 0.42 eV, for trans-1,2-dichloroethylene, cis-1,2-dichloroethylene, trichloroethylene, tetrachloroethylene, 2-chloropropene, 3-chloropropene respectively.

Helium isotope studies in the Mojave Desert, California: Implications for groundwater chronology and regional seismicity

USGS Publications Warehouse

Kulongoski, J.T.; Hilton, David R.; Izbicki, J.A.

2003-01-01

We report helium isotope and concentration results for groundwaters from the western Mojave River Basin (MRB), 130 km east of Los Angeles, CA. The basin lies adjacent to the NW-SE trending San Andreas Fault (SAF) system. Samples were collected along two groundwater flowpaths that originate in the San Gabriel Mountains and discharge to the Mojave River located ???32 km to the northeast. Additional groundwater samples were collected from Mojave River Deposits underlying the Mojave River. The primary objective of this study is to identify and quantify crustal and mantle helium contributions to the regional groundwater system. A total of 27 groundwaters, sampled previously for chemistry and isotope systematics (including 14C activity) have measured helium concentrations that increase along flowpaths from 9.9??10-8 to 1.0??10-4 cm3 STP g-1 H2O. Concomitantly, 3He/4He ratios decrease from 0.84RA to 0.11RA (RA equals the 3He/4He ratio in air=1.4??10-6). We did not record 3He/4He ratios equivalent to crustal-production values (???0.02RA) in any sample. Dissolved helium concentrations were resolved into components associated with solubility equilibration, air entrainment, mantle-derivation, in-situ production within the aquifer, and extraneous crustal fluxes. All samples contained the first four components, but only older samples had the superimposed effects of helium derived from a crustal flux. The radiogenic He component has chronological significance, and good concordance between 4He and 14C ages for younger groundwaters (<25,000 year) demonstrates the integrity of the 4 He-chronometer in this setting. Helium-rich waters could also be dated with the 4He technique, but only by first isolating the whole crustal flux (3-10??10-6 cm3 STP cm-2 year-1). Mantle-derived 3He (3Hem) is present in all MRB samples irrespective of distance from the SAF. However, regional-aquifer groundwaters near the terminus of the flowpath have a significantly greater content of mantle-derived 3He in comparison with more modern samples. We propose that faults in the basin other than the SAF may be an additional source of mantle-derived helium. The large range in 3He m concentrations may be related to fault activity; however, groundwaters with lower and more constant 3Hem contents may indicate that seismic activity along the SAF has been relatively constant for the past 30,000 years, demonstrating that ancient groundwaters may serve as an archive for paleo-seismic events. ?? 2003 Elsevier B.V. All rights reserved. All rights reserved.

Assessing the Potential of Using Biochar as a Soil Conditioner

NASA Astrophysics Data System (ADS)

Glazunova, D. M.; Kuryntseva, P. A.; Selivanovskaya, S. Y.; Galitskaya, P. Y.

2018-01-01

Biochar is a product of pyrolysis of biomass such as plant tissues, manures, sewage sludge, organic fraction of municipal solid wastes etc. Nowadays, biochar is being discussed as an alternative fertilizer that improves the air and water balance of the soil and provides soil microbiota with slow releasing biogenic elements. Many factors such as initial substrate properties, pyrolysis temperature and regime may influence biochar characteristics. In this study, characteristics of the two biochars prepared from chicken manure (ChM) and sewage sludge (SS) at 550 °C were analyzed in order to reveal their agricultural potential. It was found, that the ChM biochar had a pH value of 5.80±0.21, which was 1.6 lower than the pH of the SS sample. The electrical conductivity of the ChM sample was 6 times higher than that of the SS sample, being 6.42±0.30 mS cm-1 and 1.02±0.10 mS·cm-1, respectively. The cation exchange capacity was estimated to be 7.6±0.26 and 45±0.14 cmol·kg-1 in the ChM and SS samples, respectively. In the ChM sample total organic carbon content was 24.93±3.2%, which is nearly twice as large as that in the SS sample (12.36±4.1%), whereas total nitrogen content was estimated to be 0.33±0.03% and 0.10±0.01% for ChM and SS samples, respectively. Using scanning electronic microscopy and laser particle size distribution analysis, it was shown that the SS sample was more homogeneous in its structure and consisted of particles having a lower size of 1 to 200μm with particles of 10 to 100μm being the most frequent, while the ChM sample was nonhomogeneous and its particle size varied between 2 and 2000 μm. To observe the influence on plants, 1% of biochar was added to soil, and wheat seeds were planted. The germination index estimated for soil treated by SS biochar was estimated to be 97%, while that of soil treated by ChM biochar was lower at about 78%.

High p-type doping, mobility, and photocarrier lifetime in arsenic-doped CdTe single crystals

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nagaoka, Akira; Kuciauskas, Darius; McCoy, Jedidiah

Here, Group-V element doping is promising for simultaneously maximizing the hole concentration and minority carrier lifetime in CdTe for thin film solar cells, but there are roadblocks concerning point defects including the possibility of self-compensation by AX metastability. Herein, we report on doping, lifetime, and mobility of CdTe single crystals doped with As between 10 16 and 10 20 cm –3 grown from the Cd solvent by the travelling heater method. Evidence consistent with AX instability as a major contributor to compensation in samples doped below 10 17 cm –3 is presented, while for higher-doped samples, precipitation of a secondmore » phase on planar structural defects is also observed and may explain spatial variation in properties such as lifetime. Rapid cooling after crystal growth increases doping efficiency and mobility for times up to 20–30 days at room temperature with the highest efficiencies observed close to 45% and a hole mobility of 70 cm 2/Vs at room temperature. A doping limit in the low 10 17/cm 3 range is observed for samples quenched at 200–300 °C/h. Bulk minority carrier lifetimes exceeding 20 ns are observed for samples doped near 10 16 cm –3 relaxed in the dark and for unintentionally doped samples, while a lifetime of nearly 5 ns is observed for 10 18 cm –3 As doping. These results help us to establish limits on properties expected for group-V doped CdTe polycrystalline thin films for use in photovoltaics.« less

High p-type doping, mobility, and photocarrier lifetime in arsenic-doped CdTe single crystals

DOE PAGES

Nagaoka, Akira; Kuciauskas, Darius; McCoy, Jedidiah; ...

2018-05-07

Here, Group-V element doping is promising for simultaneously maximizing the hole concentration and minority carrier lifetime in CdTe for thin film solar cells, but there are roadblocks concerning point defects including the possibility of self-compensation by AX metastability. Herein, we report on doping, lifetime, and mobility of CdTe single crystals doped with As between 10 16 and 10 20 cm –3 grown from the Cd solvent by the travelling heater method. Evidence consistent with AX instability as a major contributor to compensation in samples doped below 10 17 cm –3 is presented, while for higher-doped samples, precipitation of a secondmore » phase on planar structural defects is also observed and may explain spatial variation in properties such as lifetime. Rapid cooling after crystal growth increases doping efficiency and mobility for times up to 20–30 days at room temperature with the highest efficiencies observed close to 45% and a hole mobility of 70 cm 2/Vs at room temperature. A doping limit in the low 10 17/cm 3 range is observed for samples quenched at 200–300 °C/h. Bulk minority carrier lifetimes exceeding 20 ns are observed for samples doped near 10 16 cm –3 relaxed in the dark and for unintentionally doped samples, while a lifetime of nearly 5 ns is observed for 10 18 cm –3 As doping. These results help us to establish limits on properties expected for group-V doped CdTe polycrystalline thin films for use in photovoltaics.« less

Moisture interaction and stability of ZOT (Zinc Orthotitanate) thermal control spacecraft coating

NASA Technical Reports Server (NTRS)

Mon, Gordon R.; Gonzalez, Charles C.; Ross, Ronald G., Jr.; Wen, Liang C.; Odonnell, Timothy

1988-01-01

Two of the many performance requirements of the zinc orthotitanate (ZOT) ceramic thermal control paint covering parts of the Jupiter-bound Galileo spacecraft are that it be sufficiently electrically conductive so as to prevent electrostatic discharge (ESD) damage to onboard electronics and that it adhere to and protect the substrate from corrosion in terrestrial environments. The bulk electrical resistivity of ZOT on an aluminum substrate was measured over the ranges 22 C to 90 C and 0 percent RH to 100 percent RH, and also in soft (10 (minus 2) Torr) and hard (10 (minus 7) Torr) vacuums. No significant temperature dependence was evident, but measured resistivity values ranged over 9 orders of magnitude: 10 to the 5th power ohm-cm at 100 percent RH greater than 10 to the 12th power ohm-cm in a hard vacuum. The latter value violates the ESD criterion for a typical 0.019 cm thick coating. The corrosion study involved exposing typical ZOT substrate combinations to two moisture environments - 30 C/85 percent RH and 85 C/85 percent RH - for 2000 hours, during which time the samples were periodically removed for front-to-back electrical resistance and scratch/peel test measurements. It was determined that the ZOT/Al and ZOT/Mg systems are stable (no ZOT delamination), although some corrosion (oxide formation) and resistivity increases observed among the ZOT/Mg samples warrant that exposure of some parts to humid environments be minimized.

Photothermal Beam Deflection Spectroscopy for the Determination of Thermal Diffusivity of Soils and Soil Aggregates

NASA Astrophysics Data System (ADS)

Proskurnin, M. A.; Korte, D.; Rogova, O. B.; Volkov, D. S.; Franko, M.

2018-07-01

Photothermal beam deflection spectroscopy (BDS) with a red He-Ne laser (632.8 nm, 35 mW) as an excitation beam source and a green He-Ne laser (543.1 nm, 2 mW) as a probe was used for estimating thermal diffusivity of several types of soil samples and individual soil aggregates with small surfaces (2 × 2 mm). It is shown that BDS can be used on demand for studies of changes in properties of soil entities of different hierarchical levels under the action of agrogenesis. It is presented that BDS clearly distinguishes between thermal diffusivities of different soil types: Sod-podzolic [Umbric Albeluvisols, Abruptic], 29 ± 3; Chernozem typical [Voronic Chernozems, Pachic], 9.9 ± 0.9; and Light Chestnut [Haplic Kastanozems, Chromic], 9.7 ± 0.9 cm2·h-1. Aggregates of chernozem soil show a significantly higher thermal diffusivity compared to the bulk soil. Thermal diffusivities of aggregates of Chernozem for virgin and bare fallow samples differ, 53 ± 4 cm2·h-1 and 45 ± 4 cm2·h-1, respectively. Micromonoliths of different Sod-podzolic soil horizons within the same profile (topsoil, depth 10-14 cm, and a parent rock with Fe illuviation, depth 180-185 cm) also show a significant difference, thermal diffusivities are 9.5 ± 0.8 cm2·h-1 and 27 ± 2 cm2·h-1, respectively. For soil micromonoliths, BDS is capable to distinguish the difference in thermal diffusivity resulting from the changes in the structure of aggregates.

SU-E-I-79: Source Geometry Dependence of Gamma Well-Counter Measurements

DOE Office of Scientific and Technical Information (OSTI.GOV)

Park, M; Belanger, A; Kijewski, M

Purpose: To determine the effect of liquid sample volume and geometry on counting efficiency in a gamma well-counter, and to assess the relative contributions of sample geometry and self-attenuation. Gamma wellcounters are standard equipment in clinical and preclinical studies, for measuring patient blood radioactivity and quantifying animal tissue uptake for tracer development and other purposes. Accurate measurements are crucial. Methods: Count rates were measured for aqueous solutions of 99m- Tc at four liquid volume values in a 1-cm-diam tube and at six volume values in a 2.2-cm-diam vial. Total activity was constant for all volumes, and data were corrected formore » decay. Count rates from a point source in air, supported by a filter paper, were measured at seven heights between 1.3 and 5.7 cm from the bottom of a tube. Results: Sample volume effects were larger for the tube than for the vial. For the tube, count efficiency relative to a 1-cc volume ranged from 1.05 at 0.05 cc to 0.84 at 3 cc. For the vial, relative count efficiency ranged from 1.02 at 0.05 cc to 0.87 at 15 cc. For the point source, count efficiency relative to 1.3 cm from the tube bottom ranged from 0.98 at 1.8 cm to 0.34 at 5.7 cm. The relative efficiency of a 3-cc liquid sample in a tube compared to a 1-cc sample is 0.84; the average relative efficiency for the solid sample in air between heights in the tube corresponding to the surfaces of those volumes (1.3 and 4.8 cm) is 0.81, implying that the major contribution to efficiency loss is geometry, rather than attenuation. Conclusion: Volume-dependent correction factors should be used for accurate quantitation radioactive of liquid samples. Solid samples should be positioned at the bottom of the tube for maximum count efficiency.« less

Hydride vapor phase GaN films with reduced density of residual electrons and deep traps

DOE Office of Scientific and Technical Information (OSTI.GOV)

Polyakov, A. Y., E-mail: aypolyakov@gmail.com; Smirnov, N. B.; Govorkov, A. V.

2014-05-14

Electrical properties and deep electron and hole traps spectra are compared for undoped n-GaN films grown by hydride vapor phase epitaxy (HVPE) in the regular process (standard HVPE samples) and in HVPE process optimized for decreasing the concentration of residual donor impurities (improved HVPE samples). It is shown that the residual donor density can be reduced by optimization from ∼10{sup 17} cm{sup −3} to (2–5) × 10{sup 14} cm{sup −3}. The density of deep hole traps and deep electron traps decreases with decreased donor density, so that the concentration of deep hole traps in the improved samples is reduced to ∼5 × 10{sup 13} cm{sup −3} versusmore » 2.9 × 10{sup 16} cm{sup −3} in the standard samples, with a similar decrease in the electron traps concentration.« less

A simple spectrophotometric method for the determination of arsenic in industrial and environmental samples using 2,4-Dihydroxy benzophenone-2-amino thiophenol.

PubMed

Deepa, K; Lingappa, Y

2014-04-24

2,4-Dihydroxy benzophenone-2-amino thiophenol (BPBT) has been proposed as new analytical reagent for the direct non-extractive spectrophotometric determination of arsenic. The reagent reacts with arsenic in acidic medium (pH=6.0, sodium acetate-acetic acid buffer) to form light greenish yellow colored 1:1 (M:L) complex. Maximum absorbance was obtained at 343 nm and remains constant for over 24 h. The molar absorptivity and Sandell's sensitivity of BPBT are found to be 6.01×10(4) L mol(-1)cm(-1) and 0.0016 μg cm(-2) respectively. The system obeys Beer's law in the range of 0.125-2.637 μg/ml of As (III). Since BPBT method is more sensitive, it was applied for the determination of arsenic in some environmental water samples. Copyright © 2013 Elsevier B.V. All rights reserved.

Scale Adhesion, Sulfur Content, and TBC Failure on Single Crystal Superalloys

NASA Technical Reports Server (NTRS)

Smialek, James L.

2002-01-01

This paper summarizes the main effects of sulfur impurity content on the cyclic oxidation resistance of single crystal superalloys, with emphasis on scale and TBC adhesion. Eleven hundred degrees C cyclic oxidation of PWA 1480 produces scale spallation leading to a weight loss of more than 30 Mg/sq cm after 500 one-hr cycles for a sulfur content of 6 ppmw. The sulfur content was reduced to levels below 0.1 ppmw by hydrogen annealing, resulting in weight gains of only 0.5 to 1.0 Mg/sq cm after 1000 one-hr cycles. Samples were produced with various sulfur contents by adjusting the annealing temperature, time, and sample thickness (i.e., diffusion product Dt/L(exp 2)). The subsequent cyclic oxidation behavior, mapped over a sulfur content/thickness diagram, shows a transition to adherent behavior at sulfur levels equivalent to 1 monolayer of total segregation. Additional information is contained in the original extended abstract.

High-Resolution Study of the First Stretching Overtones of H3Si79Br.

PubMed

Ceausu; Graner; Bürger; Mkadmi; Pracna; Lafferty

1998-11-01

The Fourier transform infrared spectrum of monoisotopic H3Si79Br (resolution 7.7 x 10(-3) cm-1) was studied from 4200 to 4520 cm-1, in the region of the first overtones of the Si-H stretching vibration. The investigation of the spectrum revealed the presence of two band systems, the first consisting of one parallel (nu0 = 4340.2002 cm-1) and one perpendicular (nu0 = 4342.1432 cm-1) strong component, and the second of one parallel (nu0 = 4405.789 cm-1) and one perpendicular (nu0 = 4416.233 cm-1) weak component. The rovibrational analysis shows strong local perturbations for both strong and weak systems. Seven hundred eighty-one nonzero-weighted transitions belonging to the strong system [the (200) manifold in the local mode picture] were fitted to a simple model involving a perpendicular component interacting by a weak Coriolis resonance with a parallel component. The most severely perturbed transitions (whose ||obs-calc || values exceeded 3 x 10(-3) cm-1) were given zero weights. The standard deviations of the fit were 1.0 x 10(-3) and 0.69 x 10(-3) cm-1 for the parallel and the perpendicular components, respectively. The weak band system, severely perturbed by many "dark" perturbers, was fitted to a model involving one parallel and one perpendicular band, connected by a Coriolis-type resonance. The K" . DeltaK = +10 to +18 subbands of the perpendicular component, which showed very high observed - calculated values ( approximately 0.5 cm-1), were excluded from this calculation. The standard deviations of the fit were 11 x 10(-3) and 13 x 10(-3) cm-1 for the parallel and the perpendicular components, respectively. Copyright 1998 Academic Press.

Screening of CO2 Laser (10.6 μm) Parameters for Prevention of Enamel Erosion

PubMed Central

Yu, Hao; de Paula Eduardo, Carlos; Meister, Jörg; Lampert, Friedrich; Attin, Thomas; Wiegand, Annette

2012-01-01

Abstract Objective: The aim of this study was to screen CO2 laser (10.6 μm) parameters to increase enamel resistance to a continuous-flow erosive challenge. Background data: A new clinical CO2 laser providing pulses of hundreds of microseconds, a range known to increase tooth acid-resistance, has been introduced in the market. Methods: Different laser parameters were tested in 12 groups (n=20) with varying fluences from 0.1 to 0.9 J/cm2, pulse durations from 80 to 400 μs and repetition rates from 180 to 700 Hz. Non-lased samples (n=30) served as controls. All samples were eroded by exposure to hydrochloric acid (pH 2.6) under continuous acid flow (60 μL/min). Calcium and phosphate release into acid was monitored colorimetrically at 30 sec intervals up to 5 min and at 1 min intervals up to a total erosion time of 15 min. Scanning electron microscopic (SEM) analysis was performed in lased samples (n=3). Data were statistically analysed by one-way ANOVA (p<0.05) and Dunnett's post-hoc tests. Results: Calcium and phosphate release were significantly reduced by a maximum of 20% over time in samples irradiated with 0.4 J/cm2 (200μs) at 450 Hz. Short-time reduction of calcium loss (≤1.5 min) could be also achieved by irradiation with 0.7 J/cm2 (300μs) at 200 and 300 Hz. Both parameters revealed surface modification. Conclusions: A set of CO2 laser parameters was found that could significantly reduce enamel mineral loss (20%) under in vitro erosive conditions. However, as all parameters also caused surface cracking, they are not recommended for clinical use. PMID:22462778

Analysis of human hair to assess exposure to organophosphate flame retardants: Influence of hair segments and gender differences.

PubMed

Qiao, Lin; Zheng, Xiao-Bo; Zheng, Jing; Lei, Wei-Xiang; Li, Hong-Fang; Wang, Mei-Huan; He, Chun-Tao; Chen, She-Jun; Yuan, Jian-Gang; Luo, Xiao-Jun; Yu, Yun-Jiang; Yang, Zhong-Yi; Mai, Bi-Xian

2016-07-01

Hair is a promising, non-invasive, human biomonitoring matrix that can provide insight into retrospective and integral exposure to organic pollutants. In the present study, we measured the concentrations of organophosphate flame retardants (PFRs) in hair and serum samples from university students in Guangzhou, China, and compared the PFR concentrations in the female hair segments using paired distal (5~10cm from the root) and proximal (0~5cm from the root) samples. PFRs were not detected in the serum samples. All PFRs except tricresyl phosphate (TMPP) and tri-n-propyl phosphate (TPP) were detected in more than half of all hair samples. The concentrations of total PFRs varied from 10.1 to 604ng/g, with a median of 148ng/g. Tris(chloroisopropyl) phosphate (TCIPP) and tri(2-ethylexyl) phosphate (TEHP) were the predominant PFRs in hair. The concentrations of most PFRs in the distal segments were 1.5~8.6 times higher than those in the proximal segments of the hair (t-test, p<0.05), which may be due to the longer exposure time of the distal segments to external sources. The values of log (PFR concentrations-distal/PFR concentrations-proximal) were positively and significantly correlated with log KOA of PFRs (p<0.05, r=0.68), indicating that PFRs with a higher log KOA tend to accumulate in hair at a higher rate than PFRs with a lower log KOA. Using combined segments of female hair, significantly higher PFR concentrations were observed in female hair than in male hair. In contrast, female hair exhibited significantly lower PFR concentrations than male hair when using the same hair position for both genders (0-5cm from the scalp). The controversial results regarding gender differences in PFRs in hair highlight the importance of segmental analysis when using hair as an indicator of human exposure to PFRs. Copyright © 2016 Elsevier Inc. All rights reserved.

Determination of iprodione in agrochemicals by infrared and Raman spectrometry.

PubMed

Armenta, Sergio; Garrigues, Salvador; de la Guardia, Miguel

2007-04-01

Two methodologies based on vibrational spectrometry--making use of Fourier transform infrared absorption (FTIR) and Raman spectrometry--were developed for iprodione determination in solid pesticide formulations. The FTIR procedure involved the extraction of iprodione by CHCl(3), and the latter determination involved measuring the peak area between 1450 and 1440 cm(-1), corrected using a horizontal baseline defined at 1481 cm(-1). FT-Raman determination was performed directly on the powdered solid products, using standard chromatography glass vials as sample cells and measuring the Raman intensity between 1003 and 993 cm(-1), with a two-point baseline correction established between 1012 and 981 cm(-1). The sensitivities obtained were 0.319 area values g mg(-1) for FTIR determination and 5.58 area values g g(-1) for FT-Raman. The repeatabilities, taken to be the relative standard deviation of five independent measurements at 1.51 mg g(-1) and 10.98% w/w concentration levels, were equal to 0.16% and 0.9% for FTIR and FT-Raman, respectively, and the limits of detection were 0.3 and 0.2% w/w (higher than those obtained for HPLC, 0.016% w/w). FTIR determination provided a sample frequency of 60 h(-1), higher than those obtained for the Raman and reference chromatography methods (25 and 8.6 h(-1), respectively). On the other hand, the new FT-Raman method eliminates reagent consumption and waste generation, and reduces the need for sample handling and the contact of operator with the pesticide. In spite of their lack of sensitivity, vibrational procedures can therefore provide viable environmentally friendly alternatives to laborious, time- and solvent-consuming reference chromatography methods for quality control in commercially available pesticide formulations.

Growth Friendly Surgery and Serial Cast Correction in the Treatment of Early-onset Scoliosis for Patients With Prader-Willi Syndrome.

PubMed

Oore, Jonathan; Connell, Braydon; Yaszay, Burt; Samdani, Amer; Hilaire, Tricia St; Flynn, Tara; El-Hawary, Ron

2018-02-02

Prader-Willi syndrome (PWS) patients can present with scoliosis which can be treated with serial cast correction (SCC) or with growth friendly surgery (GFS). This study's purpose was to describe the results of SCC as well as GFS for PWS patients with early-onset scoliosis (EOS). PWS patients were identified from 2 international multicenter EOS databases. Scoliosis, kyphosis, spine height (T1-S1), right/left hemithoracic heights/widths (RHTH, LHTH, RHTW, LHTW) were measured pretreatment, postoperation, and at 2-year follow-up. Complications were recorded. Overall, 23 patients with 2-year follow-up were identified. Pretreatment; patients treated with SCC (n=10) had mean age of 1.8±0.6 years; body mass index (BMI), 16±1.5 kg/m; scoliosis, 45±18 degrees; kyphosis, 56±9 degrees; T1-S1, 22.4±2.4 cm; RHTH, 8.0±2.0 cm; LHTH, 8.5±1.7 cm; RHTW, 6.6±1.3 cm; and LHTW, 8.0±1.0 cm. Patients treated with GFS (n=13) had mean age of 5.8±2.6 years; BMI, 21±5.4 kg/m; scoliosis, 76±14 degrees; kyphosis, 59±25 degrees; T1-S1, 24.1±3.6 cm; RHTH, 10.0±1.6 cm; LHTH, 10.6±1.6 cm; RHTW, 9.4±2.5 cm; and LHTW, 8.1±2.8 cm. At 2-year follow-up, patients treated with SCC had mean scoliosis 37±11 degrees (18% correction, P=0.06); kyphosis, 42±6 degrees (NS); T1-S1, 26.4±2.1 cm (P<0.01); RHTH, 9.0±1.1 cm (13%; P=0.30); LHTH, 10.0±1.5 cm (18%, P<0.01); RHTW, 7.4±1.1 cm (12%, P<0.01); and LHTW, 8.0±1.0 cm (0%, P=0.34). At 2-year follow-up, patients treated with GFS had mean scoliosis 42±13 degrees (45% correction, P<0.000001); kyphosis, 53±13 degrees (10%, P=0.19); T1-S1, 31.5±5.4 cm (P<0.00001); RHTH, 12.0±2.4 cm (20%; P<0.01); LHTH, 12.0±1.7 cm (13%; P<0.01); RHTW, 9.8±1.3 cm (4%; P=0.27); and LHTW, 7.9±2.3 cm (3%;P=0.11). As an entire group, patients with a BMI>17 kg/m² had more device-related than disease-related complications (P=0.09). Patients treated with SCC had 0.9 complications per patient. Patients treated with GFS had 2.2 complications per patient [≤5 y more often had ≥2 complications (P=0.05)]. At 2-year follow-up, SCC and GFS were both effective in treating EOS in PWS patients. Patients treated with SCC had significant improvements in spine height and LHTH. Patients treated with GFS had significant improvements in scoliosis magnitude, spine height, RHTH, and LHTH. Level IV-therapeutic study.

Molecular Line Emission as a Tool for Galaxy Observations (LEGO). I. HCN as a tracer of moderate gas densities in molecular clouds and galaxies

NASA Astrophysics Data System (ADS)

Kauffmann, Jens; Goldsmith, Paul F.; Melnick, Gary; Tolls, Volker; Guzman, Andres; Menten, Karl M.

2017-09-01

Trends observed in galaxies, such as the Gao & Solomon relation, suggest a linear relationship between the star formation rate and the mass of dense gas available for star formation. Validation of such trends requires the establishment of reliable methods to trace the dense gas in galaxies. One frequent assumption is that the HCN (J = 1-0) transition is unambiguously associated with gas at H2 densities ≫ 104 cm-3. If so, the mass of gas at densities ≫ 104 cm-3 could be inferred from the luminosity of this emission line, LHCN (1-0). Here we use observations of the Orion A molecular cloud to show that the HCN (J = 1-0) line traces much lower densities 103 cm-3 in cold sections of this molecular cloud, corresponding to visual extinctions AV ≈ 6 mag. We also find that cold and dense gas in a cloud like Orion produces too little HCN emission to explain LHCN (1-0) in star forming galaxies, suggesting that galaxies might contain a hitherto unknown source of HCN emission. In our sample of molecules observed at frequencies near 100 GHz (also including 12CO, 13CO, C18O, CN, and CCH), N2H+ is the only species clearly associated with relatively dense gas.

Evaluation of two methods for monitoring surface cleanliness-ATP bioluminescence and traditional hygiene swabbing.

PubMed

Davidson, C A; Griffith, C J; Peters, A C; Fielding, L M

1999-01-01

The minimum bacterial detection limits and operator reproducibility of the Biotrace Clean-Tracetrade mark Rapid Cleanliness Test and traditional hygiene swabbing were determined. Areas (100 cm2) of food grade stainless steel were separately inoculated with known levels of Staphylococcus aureus (NCTC 6571) and Escherichia coli (ATCC 25922). Surfaces were sampled either immediately after inoculation while still wet, or after 60 min when completely dry. For both organisms the minimum detection limit of the ATP Clean-Tracetrade mark Rapid Cleanliness Test was 10(4) cfu/100 cm2 (p < 0.05) and was the same for wet and dry surfaces. Both organism type and surface status (i.e. wet or dry) influenced the minimum detection limits of hygiene swabbing, which ranged from 10(2) cfu/100 cm2 to >10(7) cfu/100 cm2. Hygiene swabbing percentage recovery rates for both organisms were less than 0.1% for dried surfaces but ranged from 0.33% to 8.8% for wet surfaces. When assessed by six technically qualified operators, the Biotrace Clean-Tracetrade mark Rapid Cleanliness Test gave superior reproducibility for both clean and inoculated surfaces, giving mean coefficients of variation of 24% and 32%, respectively. Hygiene swabbing of inoculated surfaces gave a mean CV of 130%. The results are discussed in the context of hygiene monitoring within the food industry. Copyright 1999 John Wiley & Sons, Ltd.

The NuSTAR Extragalactic Survey: Average Broadband X-Ray Spectral Properties of the NuSTAR-detected AGNs

NASA Astrophysics Data System (ADS)

Del Moro, A.; Alexander, D. M.; Aird, J. A.; Bauer, F. E.; Civano, F.; Mullaney, J. R.; Ballantyne, D. R.; Brandt, W. N.; Comastri, A.; Gandhi, P.; Harrison, F. A.; Lansbury, G. B.; Lanz, L.; Luo, B.; Marchesi, S.; Puccetti, S.; Ricci, C.; Saez, C.; Stern, D.; Treister, E.; Zappacosta, L.

2017-11-01

We present a study of the average X-ray spectral properties of the sources detected by the NuSTAR extragalactic survey, comprising observations of the Extended Chandra Deep Field South (E-CDFS), Extended Groth Strip (EGS), and the Cosmic Evolution Survey (COSMOS). The sample includes 182 NuSTAR sources (64 detected at 8-24 keV), with 3-24 keV fluxes ranging between {f}3{--24{keV}}≈ {10}-14 and 6 × 10-13 erg cm-2 s-1 ({f}8{--24{keV}}≈ 3× {10}-14{--}3× {10}-13 erg cm-2 s-1) and redshifts in the range of z=0.04{--}3.21. We produce composite spectra from the Chandra + NuSTAR data (E≈ 2{--}40 {keV}, rest frame) for all the sources with redshift identifications (95%) and investigate the intrinsic, average spectra of the sources, divided into broad-line (BL) and narrow-line (NL) active galactic nuclei (AGNs), and also in different bins of X-ray column density and luminosity. The average power-law photon index for the whole sample is {{Γ }}={1.65}-0.03+0.03, flatter than the {{Γ }}≈ 1.8 typically found for AGNs. While the spectral slope of BL and X-ray unabsorbed AGNs is consistent with the typical values ({{Γ }}={1.79}-0.01+0.01), a significant flattening is seen in NL AGNs and heavily absorbed sources ({{Γ }}={1.60}-0.05+0.08 and {{Γ }}={1.38}-0.12+0.12, respectively), likely due to the effect of absorption and to the contribution from the Compton reflection component to the high-energy flux (E> 10 keV). We find that the typical reflection fraction in our spectra is R≈ 0.5 (for {{Γ }}=1.8), with a tentative indication of an increase of the reflection strength with X-ray column density. While there is no significant evidence for a dependence of the photon index on X-ray luminosity in our sample, we find that R decreases with luminosity, with relatively high levels of reflection (R≈ 1.2) for {L}10{--40{keV}}< {10}44 erg s-1 and R≈ 0.3 for {L}10{--40{keV}}> {10}44 erg s-1 AGNs, assuming a fixed spectral slope of {{Γ }}=1.8.

Model-Based Radiation Dose Correction for Yttrium-90 Microsphere Treatment of Liver Tumors With Central Necrosis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu, Ching-Sheng; Department of Nuclear Medicine, Taipei Veterans General Hospital, Taipei, Taiwan; Lin, Ko-Han

Purpose: The objectives of this study were to model and calculate the absorbed fraction {phi} of energy emitted from yttrium-90 ({sup 90}Y) microsphere treatment of necrotic liver tumors. Methods and Materials: The tumor necrosis model was proposed for the calculation of {phi} over the spherical shell region. Two approaches, the semianalytic method and the probabilistic method, were adopted. In the former method, the range--energy relationship and the sampling of electron paths were applied to calculate the energy deposition within the target region, using the straight-ahead and continuous-slowing-down approximation (CSDA) method. In the latter method, the Monte Carlo PENELOPE code wasmore » used to verify results from the first method. Results: The fraction of energy, {phi}, absorbed from {sup 90}Y by 1-cm thickness of tumor shell from microsphere distribution by CSDA with complete beta spectrum was 0.832 {+-} 0.001 and 0.833 {+-} 0.001 for smaller (r{sub T} = 5 cm) and larger (r{sub T} = 10 cm) tumors (where r is the radii of the tumor [T] and necrosis [N]). The fraction absorbed depended mainly on the thickness of the tumor necrosis configuration, rather than on tumor necrosis size. The maximal absorbed fraction {phi} that occurred in tumors without central necrosis for each size of tumor was different: 0.950 {+-} 0.000, and 0.975 {+-} 0.000 for smaller (r{sub T} = 5 cm) and larger (r{sub T} = 10 cm) tumors, respectively (p < 0.0001). Conclusions: The tumor necrosis model was developed for dose calculation of {sup 90}Y microsphere treatment of hepatic tumors with central necrosis. With this model, important information is provided regarding the absorbed fraction applicable to clinical {sup 90}Y microsphere treatment.« less

Associations of maternal organophosphate pesticide exposure and PON1 activity with birth outcomes in SAWASDEE birth cohort, Thailand

PubMed Central

Naksen, Warangkana; Prapamontol, Tippawan; Mangklabruks, Ampica; Chantara, Somporn; Thavornyutikarn, Prasak; Srinual, Niphan; Panuwet, Parinya; Ryan, P. Barry; Riederer, Anne M.; Barr, Dana Boyd

2015-01-01

Prenatal organophosphate (OP) pesticide exposure has been reported to be associated with adverse birth outcomes and neurodevelopment. However, the mechanisms of toxicity of OP pesticides on human fetal development have not yet been elucidated. Our pilot study birth cohort, the Study of Asian Women and Offspring’s Development and Environmental Exposures (SAWASDEE cohort) aimed to evaluate environmental chemical exposures and their relation to birth outcomes and infant neurodevelopment in 52 pregnant farmworkers in Fang district, Chiang Mai province, Thailand. A large array of data was collected multiple times during pregnancy including approximately monthly urine samples for evaluation of pesticide exposure, three blood samples for pesticide-related enzyme measurements and questionnaire data. This study investigated the changes in maternal acetylcholinesterase (AChE) and paraoxonase 1 (PON1) activities and their relation to urinary diakylphosphates (DAPs), class-related metabolites of OP pesticides, during pregnancy. Maternal AChE, butyrylcholinesterase (BChE) and PON1 activities were measured three times during pregnancy and urinary DAP concentrations were measured, on average, 8 times from enrollment during pregnancy until delivery. Among the individuals in the group with low maternal PON1 activity (n = 23), newborn head circumference was negatively correlated with log10 maternal ΣDEAP and ΣDAP at enrollment (gestational age=12±3 weeks; β = −1.0 cm, p = 0.03 and β = −1.8 cm, p <0.01, respectively) and at 32 weeks pregnancy (β = −1.1 cm, p = 0.04 and β = −2.6 cm, p = 0.01, respectively). Furthermore, among these mothers, newborn birthweight was also negatively associated with log10 maternal ΣDEAP and ΣDAP at enrollment (β = −219.7 g, p = 0.05 and β = −371.3 g, p = 0.02, respectively). Associations between maternal DAP levels and newborn outcomes were not observed in the group of participants with high maternal PON1 activity. Our results support previous findings from US birth cohort studies. This is the first study to report the associations between prenatal OP pesticide exposure and birth outcomes in Thailand. PMID:26186137

Associations of maternal organophosphate pesticide exposure and PON1 activity with birth outcomes in SAWASDEE birth cohort, Thailand.

PubMed

Naksen, Warangkana; Prapamontol, Tippawan; Mangklabruks, Ampica; Chantara, Somporn; Thavornyutikarn, Prasak; Srinual, Niphan; Panuwet, Parinya; Ryan, P Barry; Riederer, Anne M; Barr, Dana Boyd

2015-10-01

Prenatal organophosphate (OP) pesticide exposure has been reported to be associated with adverse birth outcomes and neurodevelopment. However, the mechanisms of toxicity of OP pesticides on human fetal development have not yet been elucidated. Our pilot study birth cohort, the Study of Asian Women and Offspring's Development and Environmental Exposures (SAWASDEE cohort) aimed to evaluate environmental chemical exposures and their relation to birth outcomes and infant neurodevelopment in 52 pregnant farmworkers in Fang district, Chiang Mai province, Thailand. A large array of data was collected multiple times during pregnancy including approximately monthly urine samples for evaluation of pesticide exposure, three blood samples for pesticide-related enzyme measurements and questionnaire data. This study investigated the changes in maternal acetylcholinesterase (AChE) and paraoxonase 1 (PON1) activities and their relation to urinary diakylphosphates (DAPs), class-related metabolites of OP pesticides, during pregnancy. Maternal AChE, butyrylcholinesterase (BChE) and PON1 activities were measured three times during pregnancy and urinary DAP concentrations were measured, on average, 8 times from enrollment during pregnancy until delivery. Among the individuals in the group with low maternal PON1 activity (n=23), newborn head circumference was negatively correlated with log10 maternal ∑DEAP and ∑DAP at enrollment (gestational age=12±3 weeks; β=-1.0 cm, p=0.03 and β=-1.8 cm, p<0.01, respectively) and at 32 weeks pregnancy (β=-1.1cm, p=0.04 and β=-2.6 cm, p=0.01, respectively). Furthermore, among these mothers, newborn birthweight was also negatively associated with log10 maternal ∑DEAP and ∑DAP at enrollment (β=-219.7 g, p=0.05 and β=-371.3g, p=0.02, respectively). Associations between maternal DAP levels and newborn outcomes were not observed in the group of participants with high maternal PON1 activity. Our results support previous findings from US birth cohort studies. This is the first study to report the associations between prenatal OP pesticide exposure and birth outcomes in Thailand. Copyright © 2015 Elsevier Inc. All rights reserved.

Total organic carbon in aggregates as a soil recovery indicator

NASA Astrophysics Data System (ADS)

Luciene Maltoni, Katia; Rodrigues Cassiolato, Ana Maria; Amorim Faria, Glaucia; Dubbin, William

2015-04-01

The soil aggregation promotes physical protection of organic matter, preservation of which is crucial to improve soil structure, fertility and ensure the agro-ecosystems sustainability. The no-tillage cultivation system has been considered as one of the strategies to increase total soil organic carbono (TOC) contents and soil aggregation, both are closely related and influenced by soil management systems. The aim of this study was to evaluate the distribution of soil aggregates and the total organic carbon inside aggregates, with regard to soil recovery, under 3 different soil management systems, i.e. 10 and 20 years of no-tillage cultivation as compared with soil under natural vegetation (Cerrado). Undisturbed soils (0-5; 5-10; and 10-20 cm depth) were collected from Brazil, Central Region. The soils, Oxisols from Cerrado, were collected from a field under Natural Vegetation-Cerrado (NV), and from fields that were under conventional tillage since 1970s, and 10 and 20 years ago were changed to no-tillage cultivation system (NT-10; NT-20 respectively). The undisturbed samples were sieved (4mm) and the aggregates retained were further fractionated by wet sieving through five sieves (2000, 1000, 500, 250, and 50 μm) with the aggregates distribution expressed as percentage retained by each sieve. The TOC was determined, for each aggregate size, by combustion (Thermo-Finnigan). A predominance of aggregates >2000 μm was observed under NV treatment (92, 91, 82 %), NT-10 (64, 73, 61 %), and NT-20 (71, 79, 63 %) for all three depths (0-5; 5-10; 10-20 cm). In addition greater quantities of aggregates in sizes 1000, 500, 250 and 50 μm under NT-10 and NT-20 treatments, explain the lower aggregate stability under these treatments compared to the soil under NV. The organic C concentration for NV in aggregates >2000 μm was 24,4; 14,2; 8,7 mg/g for each depth (0-5; 5-10; 10-20 cm, respectively), higher than in aggregates sized 250-50 μm (7,2; 5,5; 4,4 mg/g) for all depths. Although, with lower organic C contents, NT-10 and NT-20 presented the same behavior, i.e., greater amounts of organic C in bigger aggregates, (NT-10: 10,7; 9,5; 9,0 mg/g and NT-20: 18,8; 15,7; 8,6 mg/g, for each depth respectively 0-5; 5-10; 10-20 cm), and lower C contents in smaller aggregates (NT-10: 5,7; 6,1; 5,6 mg/g and NT-20: 8,2; 7,9; 6,3 mg/g , for each depth respectively 0-5; 5-10; 10-20 cm). The aggregates > 2000 μm, at 10-20 cm depth, showed similar C contents for NV, NT-10 and NT-20 (8,7; 9,0; 8,6 mg/g, respectively) suggesting that the C supply, even in natural environment, is not enough to increase organic C at 10-20 cm depth. The organic C concentration for aggregates sized 250-50 μm, in all three evaluated depths, is similar. Therefore, under NT-10 and NT-20 the smaller aggregates are not influenced by cultivation system, suggesting that the organic C inside the smaller aggregates can be retained for longer time in soil system. The results suggest, with regard to aggregate distribution and organic carbon content under NV, that soil under NT-20 is recovering. Acknowledgement: This study received financial support from CNPq

The effectiveness of the high-LET radiations from the boron neutron capture [10B(n,α) 7Li] reaction determined for induction of chromosome aberrations and apoptosis in lymphocytes of human blood samples.

PubMed

Schmid, T E; Canella, L; Kudejova, P; Wagner, F M; Röhrmoser, A; Schmid, E

2015-03-01

Provided that a selective accumulation of (10)B-containing compounds is introduced in tumor cells, following irradiation by thermal neutrons produces high-LET alpha-particles ((4)He) and recoiling lithium-7 ((7)Li) nuclei emitted during the capture of thermalized neutrons (0.025 eV) from (10)B. To estimate the biological effectiveness of this boron neutron capture [(10)B(n,α)(7)Li] reaction, the chromosome aberration assay and the flow cytometry apoptosis assay were applied. At the presence of the clinically used compounds BSH (sodium borocaptate) and BPA (p-boronophenylalanine), human lymphocytes were irradiated by sub-thermal neutrons. For analyzing chromosome aberrations, human lymphocytes were exposed to thermally equivalent neutron fluences of 1.82 × 10(11) cm(-2) or 7.30 × 10(11) cm(-2) (corresponding to thermal neutron doses of 0.062 and 0.248 Gy, respectively) in the presence of 0, 10, 20, and 30 ppm of BSH or BPA. Since the kerma coefficient of blood increased by 0.864 × 10(-12) Gy cm(2) per 10 ppm of (10)B, the kerma coefficients in blood increase from 0.34 × 10(-12) cm(2) (blood without BSH or BPA) up to 2.93 × 10(-12) Gy cm(2) in the presence of 30 ppm of (10)B. For the (10)B(n, α)(7)Li reaction, linear dose-response relations for dicentrics with coefficients α = 0.0546 ± 0.0081 Gy(-1) for BSH and α = 0.0654 ± 0.0075 Gy(-1) for BPA were obtained at 0.062 Gy as well as α = 0.0985 ± 0.0284 Gy(-1) for BSH and α = 0.1293 ± 0.0419 Gy(-1) for BPA at 0.248 Gy. At both doses, the corresponding (10)B(n, α)(7)Li reactions from BSH and BPA are not significantly different. A linear dose-response relation for dicentrics also was obtained for the induction of apoptosis by the (10)B(n, α)(7)Li reaction at 0.248 Gy. The linear coefficients α = 0.0249 ± 0.0119 Gy(-1) for BSH and α = 0.0334 ± 0.0064 Gy(-1) for BPA are not significantly different. Independently of the applied thermal neutron doses of 0.062 Gy or 0.248 Gy, the (10)B(n, α)(7)Li reaction from 30 ppm BSH or BPA induced an apparent RBE of about 2.2 for the production of dicentrics as compared to exposure to thermal neutrons alone. Since the apparent RBE value is defined as the product of the RBE of a thermal neutron dose alone times a boron localization factor which depends on the concentration of a (10)B-containing compound, this localization factor determines the biological effectiveness of the (10)B(n, α)(7)Li reaction.

Rain Splash Dispersal of Gibberella zeae Within Wheat Canopies in Ohio.

PubMed

Paul, P A; El-Allaf, S M; Lipps, P E; Madden, L V

2004-12-01

ABSTRACT Rain splash dispersal of Gibberella zeae, causal agent of Fusarium head blight of wheat, was investigated in field studies in Ohio between 2001 and 2003. Samplers placed at 0, 30, and 100 cm above the soil surface were used to collect rain splash in wheat fields with maize residue on the surface and fields with G. zeae-infested maize kernels. Rain splash was collected during separate rain episodes throughout the wheat-growing seasons. Aliquots of splashed rain were transferred to petri dishes containing Komada's selective medium, and G. zeae was identified based on colony and spore morphology. Dispersed spores were measured in CFU/ml. Intensity of splashed rain was highest at 100 cm and ranged from 0.2 to 10.2 mm h(-1), depending on incident rain intensity and sampler height. Spores were recovered from splash samples at all heights in both locations for all sampled rain events. Both macroconidia and ascospores were found based on microscopic examination of random samples of splashed rain. Spore density and spore flux density per rain episode ranged from 0.4 to 40.9 CFU cm(-2) and 0.4 to 84.8 CFU cm(-2) h(-1), respectively. Spore flux density was higher in fields with G. zeae-infested maize kernels than in fields with maize debris, and generally was higher at 0 and 30 cm than at 100 cm at both locations. However, on average, spore flux density was only 30% lower at 100 cm (height of wheat spikes) than at the other heights. The log of spore flux density was linearly related to the log of splashed rain intensity and the log of incident rain intensity. The regression slopes were not significantly affected by year, location, height, and their interactions, but the intercepts were significantly affected by both sampler height and location. Thus, our results show that spores of G. zeae were consistently splash dispersed to spike heights within wheat canopies, and splashed rain intensity and spore flux density could be predicted based on incident rain intensity in order to estimate inoculum dispersal within the wheat canopy.

Examining exposure reciprocity in a resin based composite using high irradiance levels and real-time degree of conversion values.

PubMed

Selig, Daniela; Haenel, Thomas; Hausnerová, Berenika; Moeginger, Bernhard; Labrie, Daniel; Sullivan, Braden; Price, Richard B T

2015-05-01

Exposure reciprocity suggests that, as long as the same radiant exposure is delivered, different combinations of irradiance and exposure time will achieve the same degree of resin polymerization. This study examined the validity of exposure reciprocity using real time degree of conversion results from one commercial flowable dental resin. Additionally a new fitting function to describe the polymerization kinetics is proposed. A Plasma Arc Light Curing Unit (LCU) was used to deliver 0.75, 1.2, 1.5, 3.7 or 7.5 W/cm(2) to 2mm thick samples of Tetric EvoFlow (Ivoclar Vivadent). The irradiances and radiant exposures received by the resin were determined using an integrating sphere connected to a fiber-optic spectrometer. The degree of conversion (DC) was recorded at a rate of 8.5 measurements a second at the bottom of the resin using attenuated total reflectance Fourier Transform mid-infrared spectroscopy (FT-MIR). Five specimens were exposed at each irradiance level. The DC reached after 170s and after 5, 10 and 15 J/cm(2) had been delivered was compared using analysis of variance and Fisher's PLSD post hoc multiple comparison tests (alpha=0.05). The same DC values were not reached after the same radiant exposures of 5, 10 and 15 J/cm(2) had been delivered at an irradiance of 3.7 and 7.5 W/cm(2). Thus exposure reciprocity was not supported for Tetric EvoFlow (p<0.05). For Tetric EvoFlow, there was no significant difference in the DC when 5, 10 and 15J/cm(2) were delivered at irradiance levels of 0.75, 1.2 and 1.5 W/cm(2). The optimum combination of irradiance and exposure time for this commercial dental resin may be close to 1.5 W/cm(2) for 12s. Copyright © 2015 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

The ROSAT Brightest Cluster Sample - I. The compilation of the sample and the cluster log N-log S distribution

NASA Astrophysics Data System (ADS)

Ebeling, H.; Edge, A. C.; Bohringer, H.; Allen, S. W.; Crawford, C. S.; Fabian, A. C.; Voges, W.; Huchra, J. P.

1998-12-01

We present a 90 per cent flux-complete sample of the 201 X-ray-brightest clusters of galaxies in the northern hemisphere (delta>=0 deg), at high Galactic latitudes (|b|>=20 deg), with measured redshifts z<=0.3 and fluxes higher than 4.4x10^-12 erg cm^-2 s^-1 in the 0.1-2.4 keV band. The sample, called the ROSAT Brightest Cluster Sample (BCS), is selected from ROSAT All-Sky Survey data and is the largest X-ray-selected cluster sample compiled to date. In addition to Abell clusters, which form the bulk of the sample, the BCS also contains the X-ray-brightest Zwicky clusters and other clusters selected from their X-ray properties alone. Effort has been made to ensure the highest possible completeness of the sample and the smallest possible contamination by non-cluster X-ray sources. X-ray fluxes are computed using an algorithm tailored for the detection and characterization of X-ray emission from galaxy clusters. These fluxes are accurate to better than 15 per cent (mean 1sigma error). We find the cumulative logN-logS distribution of clusters to follow a power law kappa S^alpha with alpha=1.31^+0.06_-0.03 (errors are the 10th and 90th percentiles) down to fluxes of 2x10^-12 erg cm^-2 s^-1, i.e. considerably below the BCS flux limit. Although our best-fitting slope disagrees formally with the canonical value of -1.5 for a Euclidean distribution, the BCS logN-logS distribution is consistent with a non-evolving cluster population if cosmological effects are taken into account. Our sample will allow us to examine large-scale structure in the northern hemisphere, determine the spatial cluster-cluster correlation function, investigate correlations between the X-ray and optical properties of the clusters, establish the X-ray luminosity function for galaxy clusters, and discuss the implications of the results for cluster evolution.

Mass removal by oxidation and sublimation of porous graphite during fiber laser irradiation

NASA Astrophysics Data System (ADS)

Phillips, Grady T.; Bauer, William A.; Fox, Charles D.; Gonzales, Ashley E.; Herr, Nicholas C.; Gosse, Ryan C.; Perram, Glen P.

2017-01-01

The various effects of laser heating of carbon materials are key to assessing laser weapon effectiveness. Porous graphite plates, cylinders, and cones with densities of 1.55 to 1.82 g/cm3 were irradiated by a 10-kW fiber laser at 0.075 to 3.525 kW/cm2 for 120 s to study mass removal and crater formation. Surface temperatures reached steady state values as high as 3767 K. The total decrease in sample mass ranged from 0.06 to 6.29 g, with crater volumes of 0.52 to 838 mm3, and penetration times for 12.7-mm-thick plates as short as 38 s. Minor contaminants in the graphite samples produced calcium and iron oxide to be redeposited on the graphite surface. Dramatic graphite crystalline structures are also produced at higher laser irradiances. Significantly increased porosity of the sample is observed even outside the laser-irradiated region. Total mass removed increases with deposited laser energy at a rate of 4.83 g/MJ for medium extruded graphite with an apparent threshold of 0.15 MJ. At ˜3.5 kW/cm2, the fractions of the mass removed from the cylindrical samples in the crater, surrounding trench, and outer region of decreased porosity are 38%, 47%, and 15%, respectively. Graphite is particularly resistant to damage by high power lasers. The new understanding of graphite combustion and sublimation during laser irradiation is vital to the more complex behavior of carbon composites.

Electrodeposition of zinc antimony alloy thermoelectric materials

NASA Astrophysics Data System (ADS)

Hairin, A. L. N.; Romainor, M. N.; Othman, R.; Daud, F. D. M.

2018-01-01

Zinc antimonite, Zn4Sb3 is a promising thermoelectric material because of its high thermoelectric performance and abundance of Zn and Sb in nature. Thus, in this study, samples of Zn-Sb alloy were prepared using electrodeposition method because of its simple experimental set-up, which also carried out in the room temperature. From the XRD results, all samples deposited exhibit Zn-Sb alloy compositions. The best results were S1 and S3 as they had dominant peaks that showed the crystal lattice of Zn4Sb3. From the SEM images, the surface morphology of Zn-Sb alloy deposited samples showed were all-irregular, course and rough structures. While, the atoms arrangement of the deposited samples were all flowery-like. Based on physical properties characterization, the best samples; S1 (0.1M ZnCl2-0.1M SbCl3, 100mA, 120min) and S3 (0.1M ZnCl2-0.1M SbCl3, 50mA, 120min), were selected and investigated their thermoelectric performances; electrical conductivity and Seebeck coefficient, to determine their power factor, PF. Heat capacity of the samples was also examined to relate it with thermal conductivity of Zn-Sb deposited samples. For thermoelectric performance, S1 obtained power factor of 1.37x10-7V/K. Ω.cm at 102°C with the Seebeck coefficient of 181μV/K. While as for S3, the power factor was 1.58x10-7V/K. Ω.cm with Seebeck coefficient of 113μV/K at 101°C. From DSC analysis, it showed that S3 obtained higher Cp than S1. Cp for S3 was 46.8093mJ/°C while S1 was 38.3722mJ/°C.

Constraining the H2 column density distribution at z ˜ 3 from composite DLA spectra

NASA Astrophysics Data System (ADS)

Balashev, S. A.; Noterdaeme, P.

2018-07-01

We present the detection of the average H2 absorption signal in the overall population of neutral gas absorption systems at z˜ 3 using composite absorption spectra built from the Sloan Digital Sky Survey-III damped Lyman α catalogue. We present a new technique to directly measure the H2 column density distribution function f_H_2(N) from the average H2 absorption signal. Assuming a power-law column density distribution, we obtain a slope β = -1.29 ± 0.06(stat) ± 0.10 (sys) and an incidence rate of strong H2 absorptions [with N(H2) ≳ 1018 cm-2] to be 4.0 ± 0.5(stat) ± 1.0 (sys) per cent in H I absorption systems with N(H I) ≥1020 cm-2. Assuming the same inflexion point where f_H_2(N) steepens as at z = 0, we estimate that the cosmological density of H2 in the column density range log N(H_2) (cm^{-2})= 18{-}22 is {˜ } 15 per cent of the total. We find one order of magnitude higher H2 incident rate in a sub-sample of extremely strong damped Lyman α absorption systems (DLAs) [log N(H I) (cm^{-2}) ≥ 21.7], which, together with the derived shape of f_H_2(N), suggests that the typical H I-H2 transition column density in DLAs is log N(H)(cm-2) ≳ 22.3 in agreement with theoretical expectations for the average (low) metallicity of DLAs at high-z.

Constraining the H2 column density distribution at z˜3 from composite DLA spectra

NASA Astrophysics Data System (ADS)

Balashev, S. A.; Noterdaeme, P.

2018-04-01

We present the detection of the average H2 absorption signal in the overall population of neutral gas absorption systems at z ˜ 3 using composite absorption spectra built from the Sloan Digital Sky Survey-III damped Lyman-α catalogue. We present a new technique to directly measure the H2 column density distribution function f_H_2(N) from the average H2 absorption signal. Assuming a power-law column density distribution, we obtain a slope β = -1.29 ± 0.06(stat) ± 0.10 (sys) and an incidence rate of strong H2 absorptions (with N(H2) ≳ 1018 cm-2) to be 4.0 ± 0.5(stat) ± 1.0 (sys) % in H I absorption systems with N(H I)≥1020 cm-2. Assuming the same inflexion point where f_H_2(N) steepens as at z = 0, we estimate that the cosmological density of H2 in the column density range log N(H_2) (cm^{-2})= 18-22 is ˜15% of the total. We find one order of magnitude higher H2 incident rate in a sub-sample of extremely strong DLAs (log N(H I) (cm^{-2}) ≥ 21.7), which, together with the the derived shape of f_H_2(N), suggests that the typical H I-H2 transition column density in DLAs is log N(H)(cm-2) ≳ 22.3 in agreement with theoretical expectations for the average (low) metallicity of DLAs at high-z.

Assimilation of SMOS Retrievals in the Land Information System

NASA Technical Reports Server (NTRS)

Blankenship, Clay B.; Case, Jonathan L.; Zavodsky, Bradley T.; Crosson, William L.

2016-01-01

The Soil Moisture and Ocean Salinity (SMOS) satellite provides retrievals of soil moisture in the upper 5 cm with a 30-50 km resolution and a mission accuracy requirement of 0.04 cm(sub 3 cm(sub -3). These observations can be used to improve land surface model soil moisture states through data assimilation. In this paper, SMOS soil moisture retrievals are assimilated into the Noah land surface model via an Ensemble Kalman Filter within the NASA Land Information System. Bias correction is implemented using Cumulative Distribution Function (CDF) matching, with points aggregated by either land cover or soil type to reduce sampling error in generating the CDFs. An experiment was run for the warm season of 2011 to test SMOS data assimilation and to compare assimilation methods. Verification of soil moisture analyses in the 0-10 cm upper layer and root zone (0-1 m) was conducted using in situ measurements from several observing networks in the central and southeastern United States. This experiment showed that SMOS data assimilation significantly increased the anomaly correlation of Noah soil moisture with station measurements from 0.45 to 0.57 in the 0-10 cm layer. Time series at specific stations demonstrate the ability of SMOS DA to increase the dynamic range of soil moisture in a manner consistent with station measurements. Among the bias correction methods, the correction based on soil type performed best at bias reduction but also reduced correlations. The vegetation-based correction did not produce any significant differences compared to using a simple uniform correction curve.

Microbial contamination on beef and sheep carcases in South Australia.

PubMed

Sumner, John; Petrenas, Elena; Dean, Peter; Dowsett, Paul; West, Geoff; Wiering, Rinie; Raven, Geoff

2003-03-25

A total of 523 chilled beef and lamb carcases were sampled from four abattoirs and 13 very small plants (VSPs) in South Australia during March 2002 in order to develop a microbiological profile of meat produced for domestic consumption within the State. Aerobic viable counts (AVCs) and Escherichia coli counts were obtained from samples taken by sponge-sampling the muscle-adipose tissue at sites designated for each species in the Microbiological Guidelines to the Australian Standard for Hygienic Production of Meat for Human Consumption (identical with those of the USA Pathogen Reduction: hazard analysis and critical control point (HACCP) systems: final rule). On beef carcases (n=159) mean log AVC/cm(2) was 1.82 and E. coli was detected on 18.8% of carcases (area sampled 200 cm(2)) for which the mean log of the positives was -0.34; for lamb carcases, on which 75 cm(2) was sampled (n=364), corresponding values were 2.59, 36.2% and log(10) 0.27, respectively. There was little difference in mean log AVC/cm(2) of carcases produced at abattoirs and VSPs, 1.72 versus 1.81, respectively, for beef, and 2.80 versus 2.44, respectively, for sheep. Prevalence of E. coli was lower at VSPs, however, with abattoirs having 28.4% for beef and 61.5% for sheep, compared with corresponding values of 4.7% and 18.5% at VSPs. In VSPs, the range of mean log AVC/cm(2) was 0.47-3.16 for beef and 1.63-3.65 for sheep carcases, data which will allow the Controlling Authority to assist plants to improve performance of slaughter and dressing techniques. The present survey is part of an assessment by the State meat authority of the effectiveness of co-regulation of meat hygiene between government and industry.

Synthesis of zinc oxide nanostructures on graphene/glass substrate by electrochemical deposition: effects of current density and temperature.

PubMed

Hambali, Nur Ashikyn; Yahaya, Hafizal; Mahmood, Mohamad Rusop; Terasako, Tomoaki; Hashim, Abdul Manaf

2014-01-01

The electrochemical growth of zinc oxide (ZnO) nanostructures on graphene on glass using zinc nitrate hexahydrate was studied. The effects of current densities and temperatures on the morphological, structural, and optical properties of the ZnO structures were studied. Vertically aligned nanorods were obtained at a low temperature of 75°C, and the diameters increased with current density. Growth temperature seems to have a strong effect in generating well-defined hexagonal-shape nanorods with a smooth top edge surface. A film-like structure was observed for high current densities above -1.0 mA/cm(2) and temperatures above 80°C due to the coalescence between the neighboring nanorods with large diameter. The nanorods grown at a temperature of 75°C with a low current density of -0.1 mA/cm(2) exhibited the highest density of 1.45 × 10(9) cm(-2). X-ray diffraction measurements revealed that the grown ZnO crystallites were highly oriented along the c-axis. The intensity ratio of the ultraviolet (UV) region emission to the visible region emission, I UV/I VIS, showed a decrement with the current densities for all grown samples. The samples grown at the current density below -0.5 mA/cm(2) showed high I UV/I VIS values closer to or higher than 1.0, suggesting their fewer structural defects. For all the ZnO/graphene structures, the high transmittance up to 65% was obtained at the light wavelength of 550 nm. Structural and optical properties of the grown ZnO structures seem to be effectively controlled by the current density rather than the growth temperature. ZnO nanorod/graphene hybrid structure on glass is expected to be a promising structure for solar cell which is a conceivable candidate to address the global need for an inexpensive alternative energy source.

The design of a multisource americium-beryllium (Am-Be) neutron irradiation facility using MCNP for the neutronic performance calculation.

PubMed

Sogbadji, R B M; Abrefah, R G; Nyarko, B J B; Akaho, E H K; Odoi, H C; Attakorah-Birinkorang, S

2014-08-01

The americium-beryllium neutron irradiation facility at the National Nuclear Research Institute (NNRI), Ghana, was re-designed with four 20 Ci sources using Monte Carlo N-Particle (MCNP) code to investigate the maximum amount of flux that is produced by the combined sources. The results were compared with a single source Am-Be irradiation facility. The main objective was to enable us to harness the maximum amount of flux for the optimization of neutron activation analysis and to enable smaller sample sized samples to be irradiated. Using MCNP for the design construction and neutronic performance calculation, it was realized that the single-source Am-Be design produced a thermal neutron flux of (1.8±0.0007)×10(6) n/cm(2)s and the four-source Am-Be design produced a thermal neutron flux of (5.4±0.0007)×10(6) n/cm(2)s which is a factor of 3.5 fold increase compared to the single-source Am-Be design. The criticality effective, k(eff), of the single-source and the four-source Am-Be designs were found to be 0.00115±0.0008 and 0.00143±0.0008, respectively. Copyright © 2014 Elsevier Ltd. All rights reserved.

A universally calibrated microplate ferric reducing antioxidant power (FRAP) assay for foods and applications to Manuka honey.

PubMed

Bolanos de la Torre, Amparo Angelica S; Henderson, Terence; Nigam, Poonam Singh; Owusu-Apenten, Richard K

2015-05-01

The ferric reducing antioxidant power (FRAP) assay was recently adapted to a microplate format. However, microplate-based FRAP (mFRAP) assays are affected by sample volume and composition. This work describes a calibration process for mFRAP assays which yields data free of volume effects. From the results, the molar absorptivity (ε) for the mFRAP assay was 141,698 M(-1) cm(-1) for gallic acid, 49,328 M(-1) cm(-1) for ascorbic acid, and 21,606 M(-1) cm(-1) for ammonium ferrous sulphate. The significance of ε (M(-1) cm(-1)) is discussed in relation to mFRAP assay sensitivity, minimum detectable concentration, and the dimensionless FRAP-value. Gallic acid showed 6.6 mol of Fe(2+) equivalents compared to 2.3 mol of Fe(+2) equivalents for ascorbic acid. Application of the mFRAP assay to Manuka honey samples (rated 5+, 10+, 15+, and 18+ Unique Manuka Factor; UMF) showed that FRAP values (0.54-0.76 mmol Fe(2+) per 100g honey) were strongly correlated with UMF ratings (R(2)=0.977) and total phenols content (R(2) = 0.982)whilst the UMF rating was correlated with the total phenols (R(2) = 0.999). In conclusion, mFRAP assay results were successfully standardised to yield data corresponding to 1-cm spectrophotometer which is useful for quality assurance purposes. The antioxidant capacity of Manuka honey was found to be directly related to the UMF rating. Copyright © 2014 Elsevier Ltd. All rights reserved.

137Cs Results and Interpretation of Cesium Soil Data on the Upper Fortymile Wash Alluvial Fan, Amargosa Valley, Nevada.

NASA Astrophysics Data System (ADS)

Harrington, C.

2004-12-01

Studies using 137Cs were used to produce soil Cs profiles and to use them to determine erosion rates on interchannel divides of the Fortymile Wash alluvial fan over the last 50 years. Sample locations whose 137Cs profiles most resemble the reference-sample (stable surface) profiles are located on interchannel divide areas between distributary channels. These profiles are similar to the reference profiles that have low 137Cs values (in the range of 0.02 to 0.08 pCi/g) in the 3 to 6 cm layers. However, the surface layers (1-3 cm depth) typically have values much less than the reference samples from equivalent depths (range from 0.251 to 0.421 pCi/g). The data indicate that many of these interchannel divide areas have had part of the upper layer removed. Interchannel divide areas have the least likelihood of having been submerged during floods over the last fifty years. Thus, the loss of material from these otherwise stable surfaces appears to be due to eolian processes. Erosion of an interchannel divide area with little evidence of recent water movement is most easily explained by eolian removal. Evidence for wind erosion as the predominant process on the interchannel divide areas includes the lack of new or developing stream channels and the presence of modern coppice dunes near channels on interchannel divides. The presence of nearby Big Dune and other eolian deposits provides strong support for eolian erosion and transport. The amount of material removed from the interchannel divide areas was estimated by comparing the 137Cs value of the upper 3 cm layer to that of the reference value and calculating the thickness of the layer that would have to be removed to obtain the lower value. Applying this method across the interchannel divide sample locations indicates 1 to 2 cm of material has been removed from the interchannel divide surfaces in the last 50 years. This results in erosion rates that range from 0.02 to 0.04 cm/yr. These rates are similar to erosion rates of: (a) 0.019 cm/yr predicted to occur on farmland in Amargosa Valley (obtained from BSC 2004 [DIRS 169459], Section 6.4.2 by converting 0.19 kg/m2-yr using ash bulk density of 1 g/cm3; (b) 0.02 cm/yr estimated by the U.S. Department of Agriculture to have occurred on non-cultivated cropland and pastureland in Nevada (obtained from USDA 2000 [160548], Table 11 and calculated using 1 ton/acre-yr x 907 kg/ton x 2.47 x 10-4 acre/m x 0.001 m3/kg [bulk density] x 100 cm/m = 0.02 cm/yr). Overbank deposits on the interchannel divide areas indicative of periodic flooding are uncommon and restricted to narrow strips along the channel banks. The overbank and channel deposit samples have similar 137Cs signatures (the 3 to 6 cm layers and the 6 to 9 cm layers have nearly the same values in the 0.100-0.200 pCi/g range), indicating that the material from each environ was mixed during transport and deposited as a homogeneous sediment. The absence of many overbank deposits along the channel margins today indicates that flows sufficient to form extensive overbank flooding down Fortymile Wash and its distributary channels have not occurred in more than 50 years. Therefore, the channels currently transport most of their sediment load across the fan until it reaches the toe of the fan, where deposition occurs on the broad flats to the south or into the channel of the Amargosa River.

Manganese oxide micro-supercapacitors with ultra-high areal capacitance

NASA Astrophysics Data System (ADS)

Wang, Xu; Myers, Benjamin D.; Yan, Jian; Shekhawat, Gajendra; Dravid, Vinayak; Lee, Pooi See

2013-05-01

A symmetric micro-supercapacitor is constructed by electrochemically depositing manganese oxide onto micro-patterned current collectors. High surface-to-volume ratio of manganese oxide and short diffusion distance between electrodes give an ultra-high areal capacitance of 56.3 mF cm-2 at a current density of 27.2 μA cm-2.A symmetric micro-supercapacitor is constructed by electrochemically depositing manganese oxide onto micro-patterned current collectors. High surface-to-volume ratio of manganese oxide and short diffusion distance between electrodes give an ultra-high areal capacitance of 56.3 mF cm-2 at a current density of 27.2 μA cm-2. Electronic supplementary information (ESI) available: Experimental procedures; optical images of micro-supercapacitors; areal capacitances of samples M-0.3C, M-0.6C and M-0.9C; illustration of interdigital finger electrodes; Nyquist plot of Co(OH)2 deposited on micro-electrodes. See DOI: 10.1039/c3nr00210a

SPRUCE Deep Peat Heating (DPH) Peat Water Content and Temperature Profiles for Experimental Plot Cores, June 2014 through June 2015

DOE Data Explorer

Kluber, Lauren A. [Oak Ridge National Laboratory, U.S. Department of Energy, Oak Ridge, Tennessee, U.S.A.; Phillips, Jana R. [Oak Ridge National Laboratory, U.S. Department of Energy, Oak Ridge, Tennessee, U.S.A.; Hanson, Paul J. [Oak Ridge National Laboratory, U.S. Department of Energy, Oak Ridge, Tennessee, U.S.A.; Schadt, Christopher W. [Oak Ridge National Laboratory, U.S. Department of Energy, Oak Ridge, Tennessee, U.S.A.

2016-01-01

This data set provides the peat water content and peat temperature at time of sampling for peat cores collected before and during the SPRUCE Deep Peat Heating (DPH) study. Cores were collected during three sampling events: 03 June 2014, 09 September 2014, and 16 June 2015. Two cores were extracted from hollow locations in each of the 10 experimental plots (4, 6, 8, 10, 11, 13, 16, 17, 19, and 20). Cores were partitioned into samples at 11 depth increments: 0-10, 10-20, 20-30, 30-40, 40-50, 50-75, 75-100, 100-125, 125-150, 150-175, and 175-200 cm below surface of the hollow.

Chemical Reactions of Portland Cement with Aqueous CO2 and Their Impacts on Cement's Mechanical Properties under Geologic CO2 Sequestration Conditions.

PubMed

Li, Qingyun; Lim, Yun Mook; Flores, Katharine M; Kranjc, Kelly; Jun, Young-Shin

2015-05-19

To provide information on wellbore cement integrity in the application of geologic CO2 sequestration (GCS), chemical and mechanical alterations were analyzed for cement paste samples reacted for 10 days under GCS conditions. The reactions were at 95 °C and had 100 bar of either N2 (control condition) or CO2 contacting the reaction brine solution with an ionic strength of 0.5 M adjusted by NaCl. Chemical analyses showed that the 3.0 cm × 1.1 cm × 0.3 cm samples were significantly attacked by aqueous CO2 and developed layer structures with a total attacked depth of 1220 μm. Microscale mechanical property analyses showed that the hardness and indentation modulus of the carbonated layer were 2-3 times greater than for the intact cement, but those in the portlandite-dissolved region decreased by ∼50%. The strength and elastic modulus of the bulk cement samples were reduced by 93% and 84%, respectively. The properties of the microscale regions, layer structure, microcracks, and swelling of the outer layers combined to affect the overall mechanical properties. These findings improve understanding of wellbore integrity from both chemical and mechanical viewpoints and can be utilized to improve the safety and efficiency of CO2 storage.

Gel electrolytes with I-/I3- redox mediator based on methylcellulose for dye-sensitized solar cells

NASA Astrophysics Data System (ADS)

Yusof, S. Z.; Woo, H. J.; Careem, M. A.; Arof, A. K.

2018-05-01

A new gel electrolyte comprising methylcellulose (MC), LiBOB and succinonitrile (SN) has been prepared with dimethyl sulfoxide (DMSO) as solvent. The electrolyte with composition 8.73 wt % MC-2.92 wt % LiBOB-1.01 wt % SN-87.34 wt % DMSO exhibits the highest conductivity of 1.18 mS cm-1 at 25 °C. On partially substituting LiBOB with TMAI, the sample designated as TMAI 95 has the highest conducting composition of 8.70 wt % MC-0.14 wt % LiBOB-1.01 wt % SN-2.77 wt % TMAI-0.35 wt % I2-87.03 wt % DMSO. The conductivity is 1.96 mS cm-1. This sample is used to fabricate a dye sensitized photovoltaic cell that converts photons to electricity at an efficiency of 3.46%. The conductivity of this sample has been enhanced to 3.08 mS cm-1 on addition of 1.0 wt % butyl-methyl immidazolium iodide (BMII) ionic liquid and the efficiency of the cell fabricated is 4.63%. Total replacement of LiBOB component in the electrolyte with the same amount of LiI results in a conductivity increase of ∼23.5% and the DSSC exhibits a 5.72% efficiency.

Broiler carcass contamination with Campylobacter from feces during defeathering.

PubMed

Berrang, M E; Buhr, R J; Cason, J A; Dickens, J A

2001-12-01

Three sets of experiments were conducted to explore the increase in recovery of Campylobacter from broiler carcasses after defeathering. In the first set of experiments, live broilers obtained from a commercial processor were transported to a pilot plant, and breast skin was sampled by a sponge wipe method before and after defeathering. One of 120 broiler breast skin samples was positive for Campylobacter before defeathering, and 95 of 120 were positive after defeathering. In the second set of experiments, Campylobacter-free flocks were identified, subjected to feed withdrawal, and transported to the pilot plant. Carcasses were intracloacally inoculated with Campylobacter (10(7) CFU) just prior to entering the scald tank. Breast skin sponge samples were negative for Campylobacter before carcasses entered the picker (0 of 120 samples). After defeathering, 69 of 120 samples were positive for Campylobacter, with an average of log10 2.7 CFU per sample (approximately 30 cm2). The third set of experiments was conducted using Campylobacter-positive broilers obtained at a commercial processing plant and transported live to the pilot plant. Just prior to scalding, the cloacae were plugged with tampons and sutured shut on half of the carcasses. Plugged carcasses were scalded, and breast skin samples taken before and after defeathering were compared with those collected from control broilers from the same flock. Prior to defeathering, 1 of 120 breast skin sponge samples were positive for the control carcasses, and 0 of 120 were positive for the plugged carcasses. After passing through the picker, 120 of 120 control carcasses had positive breast skin sponge samples, with an average of log10 4.2 CFU per sample (approximately 30 cm2). Only 13 of 120 plugged carcasses had detectable numbers of Campylobacter on the breast skin sponge, with an average of log10 2.5 CFU per sample. These data indicate that an increase in the recovery of Campylobacter after defeathering can be related to the escape of contaminated feces from the cloaca during defeathering.

Effect of feeder space during the growing and laying periods and the rate of feed increase at the onset of lay on broiler breeder female reproductive function.

PubMed

Leksrisompong, N; Romero-Sanchez, H; Oviedo-Rondón, E O; Brake, J

2014-07-01

A study was conducted to examine how 2 feeder space allocations during the rearing period followed by 2 feeder space allocations after photostimulation and 2 female feeding to peak programs (fast or slow) affected female broiler breeder reproductive performance and mortality. Sixteen pens of 76 breeder females each were equipped with either 4 tube feeders with a 132 cm circumference pan (7.0 cm/female) or 6 feeders (10.4 cm/female) to 21 wk of age. Thereafter, 64 females were moved to breeding pens, photostimulated, and fed sex-separate from either 3 (6.2 cm/female) or 5 (10.3 cm/female) feeders with either fast or slow feeding to peak feeding programs applied to complete a 2 × 2 × 2 factorial design. Seven males that were separately reared in a similar manner were added per pen. Individual female BW was determined at 6, 20, and 32 wk of age and BW uniformity assessed. Greater feeder space during rearing increased BW at 32 wk of age, whereas greater feeder space during lay or slow feeding to peak decreased BW at 32 wk. There were no differences in BW uniformity. Hens from the 10.4 to 10.3 cm/female combination produced a significantly greater number of eggs as compared with the 7.0 to 10.3 cm/female and 10.4 to 6.2 cm/female combinations with the 7.0 to 6.2 cm/female combination intermediate. Percentage hen-day egg production of the 10.4 to 10.3 cm/female combination hens was significantly greater than all other combinations. Livability was improved in the 10.4 to 10.3 cm/female combination relative to the 7.0 to 10.3 cm/female combination with the others intermediate. The fast feeding to peak program increased yolk weight as well as yolk:albumen ratio at 28 and 30 wk of age, but egg weight did not differ. These data indicated that increased or decreased feeder space between the growing and laying periods did not affect broiler breeder female BW, uniformity, egg weight, fertility, or hatchability. The 10.3 cm/female laying feeder space exhibited the best hen-day egg production in combination with 10.4 cm/pullet rearing but not with 7.0 cm/pullet rearing space. In a similar manner, hen mortality was greater in the 7.0 to 10.3 cm/female feeder space combination that the 10.4 to 10.3 cm/female combination. © 2014 Poultry Science Association Inc.

Assessment of Fluoride Concentration of Soil and Vegetables in Vicinity of Zinc Smelter, Debari, Udaipur, Rajasthan.

PubMed

Bhat, Nagesh; Jain, Sandeep; Asawa, Kailash; Tak, Mridula; Shinde, Kushal; Singh, Anukriti; Gandhi, Neha; Gupta, Vivek Vardhan

2015-10-01

As of late, natural contamination has stimulated as a reaction of mechanical and other human exercises. In India, with the expanding industrialization, numerous unsafe substances are utilized or are discharged amid generation as cleans, exhaust, vapours and gasses. These substances at last are blended in the earth and causes health hazards. To determine concentration of fluoride in soils and vegetables grown in the vicinity of Zinc Smelter, Debari, Udaipur, Rajasthan. Samples of vegetables and soil were collected from areas situated at 0, 1, 2, 5, and 10 km distance from the zinc smelter, Debari. Three samples of vegetables (i.e. Cabbage, Onion and Tomato) and 3 samples of soil {one sample from the upper layer of soil (i.e. 0 to 20 cm) and one from the deep layer (i.e. 20 - 40 cm)} at each distance were collected. The soil and vegetable samples were sealed in clean polythene bags and transported to the laboratory for analysis. One sample each of water and fertilizer from each distance were also collected. The mean fluoride concentration in the vegetables grown varied between 0.36 ± 0.69 to 0.71 ± 0.90 ppm. The fluoride concentration in fertilizer and water sample from various distances was found to be in the range of 1.4 - 1.5 ppm and 1.8 - 1.9 ppm respectively. The fluoride content of soil and vegetables was found to be higher in places near to the zinc smelter.

Fourier Image Synthesis and Slope Spectrum Analysis of Deepwater, Windwave Scenes Viewed at Brewster’s Angle

DTIC Science & Technology

1990-01-01

reflection is simulated by a one- level ray trace with selective filtering of the RGB color ’spectrum’ Fractal and sequential Markov-chain synthesis tech...above water level [cm/sec], and vfric = the wind friction velocity at the water surface (i.e. z = 0 cm). vfric and the wind velocity v [cm/sec] at height...12 cm/sec 1000 0 -4.5 -4.0 -3.5 -3.0 -2.5 -2.0 -1.5 -1.0 -. 5 0 .5 1.0 LOGI0(k (k: 1/cm) ------------------------------------------------------ FIGUE

Pole lengths influence O2-cost during double poling in highly trained cross-country skiers.

PubMed

Carlsen, Camilla Høivik; Rud, Bjarne; Myklebust, Håvard; Losnegard, Thomas

2018-02-01

In elite cross-country skiing, double poling is used in different terrain. This study compared O 2 -cost and kinematics during double poling with four different pole lengths [self-selected (SS), SS - 5 cm, SS + 5 cm, SS + 10 cm] at Low versus Moderate incline. Thirteen highly trained male cross-country skiers (mean ± SD 23 ± 3 years; 182 ± 4 cm; 77 ± 6 kg) completed eight submaximal trials with roller skis on a treadmill at two conditions: "Low incline" (1.7°; 4.5 m s -1 ) and "Moderate incline" (4.5°; 2.5 m s -1 ) with each of the four pole lengths. O 2 -cost and 3D body kinematics were assessed in each trial. In Low incline, SS + 10 cm induced a lower O 2 -cost than all the other pole lengths [P < 0.05; effect size (ES) 0.5-0.8], whereas no differences were found between the remaining pole lengths (P > 0.05; ES 0.2-0.4). In Moderate incline, significant differences between all pole lengths were found for O 2 -cost, with SS - 5 cm > SS > SS + 5 cm > SS + 10 cm (P < 0.05; ES 0.6-1.8). The relative differences in O 2 -cost between SS and the other pole lengths were greater in Moderate incline than Low incline (SS - 5 cm; 1.5%, ES 0.8, SS + 5 cm; 1.3%, ES 1.0, and SS + 10 cm; 1.9%, ES 1.0, all P < 0.05). No difference was found in cycle, poling or reposition times between pole lengths. However, at both conditions a smaller total vertical displacement of center of mass was observed with SS + 10 cm compared to the other pole lengths. Increasing pole length from SS - 5 cm to SS + 10 cm during double poling induced lower O 2 -cost and this advantage was greater in Moderate compared to Low incline.

Effect of contrast enhancement on measurement of carotid artery intimal medial thickness.

PubMed

Macioch, James E; Katsamakis, C Dean; Robin, Jason; Liebson, Philip R; Meyer, Peter M; Geohas, Chris; Raichlen, Joel S; Davidson, Michael H; Feinstein, Steven B

2004-02-01

Previous studies have used standard B-mode ultrasound to quantify the aggregate mean intimal medial thickness (IMT) of the near and far wall of the common carotid artery (CCA). Many investigators have had difficulty in accurately evaluating the near wall IMT secondary to difficulty in discerning the vessel lumen and intima. The purpose of this study is to determine the effect of contrast enhanced ultrasound on IMT measurement when compared with non-enhanced images. Twenty-six patients who had standard carotid ultrasounds completed over a 6-month period were evaluated, with 24 imaged by the same sonographer. Five to six measurements of the near and far walls were obtained over a 1 cm distance, beginning and ending 0.5 cm and 1.5 cm proximal to the carotid bifurcation. The measurements were made with and without the contrast agent Optison (perflutren protein type-A microspheres), which was given as an i.v. bolus (0.5-0.7 cc). Of those imaged by the same sonographer, 40 carotid arteries were examined and a total of 867 measurements were obtained. A total of 10% of the carotid ultrasounds were restudied approximately 1 month after the initial interpretation to assess observer accuracy. The near wall CCA mean (SD) IMT was 0.075 (0.019) cm for left with contrast versus 0.067 (0.023) cm for left without contrast and 0.089 (0.024) cm for right with versus 0.071 (0.022) cm for right without, p < or = 0.0001 both sides. For the far wall of the CCA, the mean (SD) IMT comparison was 0.075 (0.021) cm for left with versus 0.070 (0.016) cm for left without, p = 0.005, and 0.070 (0.023) cm for right with versus 0.070 (0.016) cm for right without, p = 0.68. In conclusion, contrast-enhanced IMT measurement showed a highly statistically significant difference in near carotid wall thickness determinations versus non-contrast values. The thicker measurement is in agreement with previously reported data showing that non-contrast images underestimated near wall common carotid IMT in histologic samples.

Biocontrol of Escherichia coli O157: H7 on fresh-cut leafy greens.

PubMed

Boyacioglu, Olcay; Sharma, Manan; Sulakvelidze, Alexander; Goktepe, Ipek

2013-01-01

The effect of a bacteriophage cocktail (EcoShield™) that is specific against Escherichia coli O157:H7 was evaluated against a nalidixic acid-resistant enterohemorrhagic E. coli O157:H7 RM4407 (EHEC) strain on leafy greens stored under either (1) ambient air or (2) modified atmosphere (MA; 5% O 2 /35% CO 2 /60% N 2 ). Pieces (~2 × 2 cm 2 ) of leafy greens (lettuce and spinach) inoculated with 4.5 log CFU/cm 2 EHEC were sprayed with EcoShield™ (6.5 log PFU/cm 2 ). Samples were stored at 4 or 10°C for up to 15 d. On spinach, the level of EHEC declined by 2.38 and 2.49 log CFU/cm 2 at 4 and 10°C, respectively, 30 min after phage application (p ≤ 0.05). EcoShield™ was also effective in reducing EHEC on the surface of green leaf lettuce stored at 4°C by 2.49 and 3.28 log units in 30 min and 2 h, respectively (p ≤ 0.05). At 4°C under atmospheric air, the phage cocktail significantly (p ≤ 0.05) lowered the EHEC counts in one day by 1.19, 3.21 and 3.25 log CFU/cm 2 on spinach, green leaf and romaine lettuce, respectively compared with control (no bacteriophage) treatments. When stored under MA at 4°C, phages reduced (p ≤ 0.05) EHEC populations by 2.18, 3.50 and 3.13 log CFU/cm 2 , on spinach, green leaf and romaine lettuce. At 10°C, EHEC reductions under atmospheric air storage were 1.99, 3.90 and 3.99 log CFU/cm 2 (p ≤ 0.05), while population reductions under MA were 3.08, 3.89 and 4.34 logs on spinach, green leaf and romaine lettuce, respectively, compared with controls (p ≤ 0.05). The results of this study showed that bacteriophages were effective in reducing the levels of E. coli O157:H7 on fresh leafy produce, and that the reduction was further improved when produce was stored under the MA conditions.

Fourier Transform Spectroscopy of 18O-Enriched Carbonyl Sulfide from 1825 to 2700 cm -1

NASA Astrophysics Data System (ADS)

Strugariu, T.; Naı̈m, S.; Fayt, A.; Bredohl, H.; Blavier, J.-F.; Dubois, I.

1998-06-01

We have measured the Fourier transform spectrum of carbonyl sulfide from 1825 to 2700 cm-1, using a sample enriched in both18O (94.0%) and17O (1.54%). A careful calibration yields a line-position accuracy between 1.5 and 3.0 10-5cm-1. We have observed and analyzed 118 infrared bands of which 93 are measured for the first time: 55 for18O12C32S, 20 for18O12C34S, 11 for18O12C33S, 1 for18O12C36S, 12 for17O12C32S, 4 for17O12C34S, 2 for17O12C33S, and 13 for18O13C32S. Intensities are also reported and analyzed for all those bands. The intensity accuracy is better than 10%, and the precision of approximately 1% allows us to determine some Herman-Wallis coefficients.

Effect of oxygen partial pressure during preparation of rutile-type FeNbTiO6 on electrical and dielectric properties, thermopower and Mössbauer spectra

NASA Astrophysics Data System (ADS)

Günther, A.; Hochleitner, R.; Lohringer, H.; Schmidbauer, E.; Schöttler-Himmel, A.; Volk, M.

2017-05-01

Electrical and dielectric properties were measured on rutile-type FeNbTiO6, sintered in air, CO2 or 5%H2/CO2 atmosphere between temperatures of 1423 and 1573 K. The individual samples show characteristic differences in DC and AC conductivity, dielectric constant ε(ω) (ω is angular frequency), dielectric loss and dissipation factor. Attempts were made to distinguish between bulk, grain boundary (GB) and sample-electrode (SE) processes. Samples show very high relaxor-like ε(ω) peaks at 500-600 K using Ag-paint contacts as expected from previous studies during preparation in air that is of interest for industrial application; utilizing Pt-paint and using slightly reducing sintering conditions, a clear variation was observed. These findings point to a notable influence of GB and/or SE effects on the experimental ε(ω), in addition to the intrinsic origin by polar nanoregions, as suggested earlier. Complex plane impedance plots are characterized by semicircular arcs due to bulk, GB and/or SE charge transport. The derived DC conductivity σDC shows Arrhenius behavior with activation energy of EA≈0.27-0.37 eV and σDC(300 K) ≈1×10-6-3×10-4 Ω-1cm-1 for the bulk, EA≈0.7-0.9 eV and σDC(300 K)≈5×10-10-1×10-4 Ω-1cm-1 for GB and/or SE processes, depending on the preparation conditions. The thermopower is small and negative, hence n-type conduction occurs and the charge carriers are electrons or electron polarons. 57Fe Mössbauer spectroscopy enabled to gain knowledge of local nonstoichiometry in the environment of Fe cations, presumably affecting electrical conduction in the bulk and GBs; after sample preparation in reducing conditions, apart from Fe3+ also the presence of Fe2+ ions was established.

Production of O(-) from CO2 by dissociative electron attachment

NASA Technical Reports Server (NTRS)

Orient, O. J.; Srivastava, S. K.

1983-01-01

Dissociative electron attachment cross-section measurements for the production of O(-) from CO2 are performed using a crossed target-beam - electron-beam collision geometry and a quadrupole mass spectrometer. The relative flow technique is used in determining the absolute values of the cross sections. The attachment energies corresponding to the five cross-section maxima are given. They are 4.4 + or - 0.1, 8.2 + or - 0.1, 13.0 + or - 0.2, 16.9 + or - 0.2, and 19.4 + or 0.2 eV. Also given are the cross sections at these maxima: 1.43 x 10 to the -19th sq cm, 4.48 x 10 to the -19th sq cm, 8.1 x 10 to the -21st sq cm, 8.1 x 10 to the -21st sq cm, and 1.2 x 10 to the -20th sq cm, respectively.

Comparing molecular composition of dissolved organic matter in soil and stream water: Influence of land use and chemical characteristics.

PubMed

Seifert, Anne-Gret; Roth, Vanessa-Nina; Dittmar, Thorsten; Gleixner, Gerd; Breuer, Lutz; Houska, Tobias; Marxsen, Jürgen

2016-11-15

Electrospray ionization Fourier transform ion cyclotron resonance mass spectrometry (ESI-FT-ICR-MS) was used to examine the molecular composition of dissolved organic matter (DOM) from soils under different land use regimes and how the DOM composition in the catchment is reflected in adjacent streams. The study was carried out in a small area of the Schwingbach catchment, an anthropogenic-influenced landscape in central Germany. We investigated 30 different soil water samples from 4 sites and different depths (managed meadow (0-5cm, 40-50cm), deciduous forest (0-5cm), mixed-coniferous forest (0-5cm) and agricultural land (0-5cm, 40-50cm)) and 8 stream samples. 6194 molecular formulae and their magnitude-weighted parameters ((O/C)w, (H/C)w, (N/C)w, (AI-mod)w, (DBE/C)w, (DBE/O)w, (DBE-O)w, (C#)w, (MW)w) were used to describe the molecular composition of the samples. The samples can be roughly divided in three groups. Group 1 contains samples from managed meadow 40-50cm and stream water, which are characterized by high saturation compared to samples from group 2 including agricultural samples and samples from the surface meadow (0-5cm), which held more nitrogen containing and aromatic compounds. Samples from both forested sites (group 3) are characterized by higher molecular weight and O/C ratio. Environmental parameters vary between sites and among these parameters pH and nitrate significantly affect chemical composition of DOM. Results indicate that most DOM in streams is of terrestrial origin. However, 120 molecular formulae were detected only in streams and not in any of the soil samples. These compounds share molecular formulae with peptides, unsaturated aliphatics and saturated FA-CHO/FA-CHOX. Compounds only found in soil samples are much more aromatic, have more double bonds and a much lower H/C ratio but higher oxygen content, which indicates the availability of fresh plant material and less microbial processed material compared to stream samples. Copyright © 2016 Elsevier B.V. All rights reserved.

Application of a novel antimicrobial coating on roast beef for inactivation and inhibition of Listeria monocytogenes during storage.

PubMed

Wang, Luxin; Zhao, Liang; Yuan, Jing; Jin, Tony Z

2015-10-15

The antilisterial efficacy of novel coating solutions made with organic acids, lauric arginate ester, and chitosan was evaluated in a three-stage study on inoculated roast beef for the first time. Ready-to-eat roast beef was specially ordered from the manufacturer. The meat surface was inoculated with five-strain Listeria monocytogenes cocktail inoculums at two different levels, ~3 and 6 Log CFU/cm(2) and treated with the stock solution (HAMS), the 1:5 diluted solution (MAMS), and the 1:10 diluted solution (LAMS) (stage 1). During the 20 min contact time, the antimicrobial coatings reduced the Listeria populations by approximately 0.9-0.3 Log CFU/cm(2). The higher the concentrations of the antimicrobial solution, the better the antilisterial effects were. The treated inoculated beef samples were then stored at 4 °C for 30 days. During storage, Listeria growth inhibition effects were seen. While no growth was seen from the HAMS-treated samples, a 1.6 Log CFU/cm(2) increase was seen for MAMS-treated samples, a 4.6 Log CFU/cm(2) increase was seen for LAMS-treated samples, and a 5.7 Log CFU/cm(2) increase was seen for NoAMS-treated samples on Day 30 (~3 Log CFU/cm(2) inoculation level). In the second stage, the impact of the roast beef storage time on solution's antilisterial effect was evaluated. Results showed that the effect of the antimicrobial solution was dependent on both the initial inoculation levels and storage times. In stage 3, the effect of the antimicrobial solution on roast beef quality was studied with both instrument measurement and sensory evaluation. Minor changes in color, pH, and water activity were found. However, only limited sensory differences were seen between the treated and untreated samples. When panels were able to accurately find color differences between samples, they preferred the treated samples. The findings of this research proved the antilisterial efficacy of the novel antimicrobial solution and showed its potential for being used as a roast beef cut surface coating to control Listeria contamination and for color protection. Copyright © 2015 Elsevier B.V. All rights reserved.

The Effect of Long-term Nutrient Addition on Peat Properties in an Ombrotrophic Bog

NASA Astrophysics Data System (ADS)

Moore, T. R.; Bubier, J. L.; Knorr, K. H.; Roy, C.

2017-12-01

Atmospheric inputs of nutrients, particularly N and P, to ecosystems have increased and may have a significant effect on nutrient-deficient peatlands such as bogs. At the Mer Bleue ombrotrophic bog near Ottawa, Canada, we have conducted an experiment over 10 to 20 years by adding 1.6 to 6.4 g N m-2 yr-1 (as NH4NO3), with/without 6 g P m-2 yr-1 (as K phosphate), to evaluate the effect of increased inputs on ecosystem functions. Increased N and P amendment has changed the vegetation from a mixed shrub-Sphagnum community into one dominated by shrubs with the disappearance of mosses, with changes in plant production and litter input. The largest N and P amendments have resulted in an increase in bulk density at 0-10 cm and a lowering of the peat surface by 10 to 20 cm, creating an effective rise in the water table and an increase in CH4 emission from 15 to 50 mg m-2 d-1. Peat cores to a depth of 40 cm were collected after 10 to 15 yr of amendment and showed little change in soil pH (range 4.1 to 4.5). There were substantial increases in the concentration of N and P in the peat (8 to 14 and 0.5 to 1.5 mg g-1, respectively) and general decreases in Ca and Mg concentration. The von Post humification index increased by about 1 unit in the heavily fertilized plots, with shrub leaves replacing Sphagnum as the primary litterfall. FTIR analysis of the 0-20 cm peat showed significant increases in abundance of phenolic+aliphatic, aromatic, and carboxylic relative to polysaccharide components, revealed by the following ratios of absorbance at the respective wavenumbers: 1420/1090 cm-1, 0.41 to 0.45; 1510/1090 cm-1, 0.23 to 0.30; 1630/1090 cm-1, 0.53 to 0.65; and 1720/1090 cm-1, 0.44 to 0.48, respectively. Laboratory incubations of peat samples showed that potential rates of aerobic CH4 consumption were unaffected by nutrient treatment, apart from position relative to the water table, whereas potential rates of anaerobic CH4 production near the water table increased under the P amendment. Potential rates of aerobic CO2 production generally decreased with depth in the cores, but were not strongly related to decomposition properties (e.g. Von Post, FTIR). This study shows the profound effect of increased N and P addition on the vegetation composition, carbon cycling and peat chemical properties and decomposability of this ombrotrophic mire.

The Architecture of Fat Grafting: What Lies beneath the Surface.

PubMed

Bourne, Debra A; James, Isaac B; Wang, Sheri S; Marra, Kacey G; Rubin, J Peter

2016-03-01

Fat grafting is a powerful procedure limited by unpredictable volume loss. Grafted tissue survives via plasmatic imbibition until neovascularization occurs; therefore, fat that is deposited more than 0.2 cm from capillaries will undergo central necrosis. This study aims to determine the architecture of fat deposits within the recipient bed following fat grafting. Fat was harvested by liposuction and stained with methylene blue. Stained fat was grafted into 4 × 4 × 2-cm sections of pannus tissue at graft-to-recipient volume ratios ranging from 1:10 to 1:1. Each tissue block was sectioned for stained graft visualization. The diameter of each deposit and the percentage with a radius greater than 0.2 cm were recorded. Average tunnel diameter was 0.20 ± 0.01 cm at a graft-to-recipient ratio of 1:10, 0.25 ± 0.01 cm at 1:8, 0.26 ± 0.01 cm at 1:6, 0.31 ± 0.01 cm at 1:4, 0.40 ± 0.01 cm at 1:2, and 0.57 ± 0.02 cm at 1:1. All comparisons reached statistical significance (p ≤ 0.05) except 1:8 versus 1:6 (p = 0.96). The percentage of fat parcels with a radius greater than 0.2 cm was 3.0 percent at 1:10, 5.3 percent at 1:8, 9.5 percent at 1:6, 20.9 percent at 1:4, 42.0 percent at 1:2, and 68.3 percent at 1:1. All percentage comparisons were significant except 1:10 versus 1:8 (p = 0.15). As the total volume transferred increases, grafted deposits coalesce to form larger globules, particularly at ratios beyond 1:4, likely contributing to central necrosis and subsequent volume loss. Therapeutic, V.

Effects of electron irradiation and temperature on 1 ohm-cm and 10 ohm-cm silicon solar cells

NASA Technical Reports Server (NTRS)

Nicoletta, C. A.

1973-01-01

One OHM-cm and 10 OHM-cm silicon solar cells were exposed to 1.0 MeV electrons at a fixed flux of 10 to the 11th power e/sq cm/sec and fluences of 10 to the 13th power, 10 to the 14th power and 10 to the 15th power e/sq.cm. 1-V curves of the cells were made at room temperature, - 63 C and + or - 143 C after each irradiation. A value of 139.5 mw/sq cm was used as AMO incident energy rate per unit area. The 10 OHM-cm cells appear more efficient than 1 OHM-cm cells after exposure to a fluence greater than 10 to the 14th power e/sq cm. The 1.0 MeV electron damage coefficients for both 1 OHM-cm and 10 OHM-cm cells are somewhat less than those for previously irradiated cells at room temperature. The values of the damage coefficients increase as the cell temperatures decrease. Efficiencies pertaining to maximum power output are about the same as those of n on p silicon cells evaluated previously.

Dosimetric Comparison of Involved-Field Three-Dimensional Conformal Photon Radiotherapy and Breast-Sparing Proton Therapy for the Treatment of Hodgkin's Lymphoma in Female Pediatric Patients

DOE Office of Scientific and Technical Information (OSTI.GOV)

Andolino, David L., E-mail: dandolin@iupui.edu; Hoene, Ted; Xiao, Lu

2011-11-15

Purpose: To assess the potential reduction in breast dose for young girls with Hodgkin's lymphoma (HL) treated with breast-sparing proton therapy (BS-PT) as compared with three-dimensional conformal involved-field photon radiotherapy (3D-CRT). Methods and Materials: The Clarian Health Cancer Registry was queried for female pediatric patients with the diagnosis of HL who received radiotherapy at the Indiana University Simon Cancer Center during 2006-2009. The original CT simulation images were obtained, and 3D-CRT and BS-PT plans delivering 21 Gy or cobalt gray equivalent (CGE) in 14 fractions were created for each patient. Dose-volume histogram data were collected for both 3D-CRT and BS-PTmore » plans and compared by paired t test for correlated samples. Results: The cancer registry provided 10 female patients with Ann Arbor Stage II HL, aged 10-18 years at the time of treatment. Both mean and maximum breast dose were significantly less with BS-PT compared with 3D-CRT: 0.95 CGE vs. 4.70 Gy (p < 0.001) and 21.07 CGE vs. 23.11 Gy (p < 0.001), respectively. The volume of breast receiving 1.0 Gy/CGE and 5.0 Gy/CGE was also significantly less with BS-PT, 194 cm{sup 3} and 93 cm{sup 3}, respectively, compared with 790 cm{sup 3} and 360 cm{sup 3} with 3D-CRT (p = 0.009, 0.013). Conclusion: Breast-sparing proton therapy has the potential to reduce unnecessary breast dose in young girls with HL by as much as 80% relative to involved-field 3D-CRT.« less

Experimental Air-Broadened Line Parameters in the nu2 Band of CH3D

NASA Technical Reports Server (NTRS)

Cross, Adriana Predoi; Brawley-Tremblay, Shannon; Povey, Chad; Smith, Mary Ann H.

2007-01-01

In this study we report the first experimental measurements of air-broadening and air-induced pressure-shift coefficients for approximately 378 transitions in the nu2 fundamental band of CH3D. These results were obtained from analysis of 17 room temperature laboratory absorption spectra recorded at 0.0056 cm(exp -1) resolution using the McMath-Pierce Fourier transform spectrometer located on Kitt Peak, Arizona. Three absorption cells with path lengths of 10.2, 25 and 150 cm were used to record the spectra. The total sample pressures ranged from 0.129x10(exp -2) to 52.855x10(exp -2) atm with CH3D volume mixing ratios of approximately 0.0109 in air. The spectra were analyzed using a multispectrum non-linear least-squares fitting technique. We report measurements for air pressure-broadening coefficients for transitions with quantum numbers as high as J" = 20 and K = 15, where K" = K' equivalent to K (for a parallel band). The measured air broadening coefficients range from 0.0205 to 0.0835 cm(exp -1) atm(exp -1) at 296 K. All the measured pressure-shift coefficients are negative and are found to vary from about -0.0005 to -0.0080 cm(exp -1) atm(exp -1) at the temperature of the spectra. We have examined the dependence of the measured broadening and shift parameters on the J" and K quantum numbers and also developed empirical expressions to describe the broadening coefficients in terms of m (m = -J", J" and J" + 1 in the (sup Q)P- (sup Q)Q-, and (sup Q)R-branch, respectively) and K. On average, the empirical expressions reproduce the measured broadening coefficients to within 4.4%.

Comparison of absorbed-dose-to-water units for Co-60 and high-energy x-rays between PTB and LNE-LNHB

NASA Astrophysics Data System (ADS)

Delaunay, F.; Kapsch, R.-P.; Gouriou, J.; Illemann, J.; Krauss, A.; Le Roy, M.; Ostrowsky, A.; Sommier, L.; Vermesse, D.

2012-10-01

During the Euramet project JRP7 ‘External Beam Cancer Therapy’, PTB and LNE-LNHB used primary standards to determine the absorbed dose to water under IMRT conditions (in small fields). PTB used a water calorimeter to determine the absorbed-dose-to-water references in 6 MV and 10 MV beams for field sizes of 10 cm × 10 cm and 3 cm × 3 cm while LNE-LNHB used graphite calorimeters in 6 MV and 12 MV beams for field sizes of 10 cm × 10 cm, 4 cm × 4 cm and 2 cm × 2 cm. The purpose of this study is to compare PTB and LNE-LNHB new absorbed-dose-to-water references. LNE-LNHB sent an Exradin A1SL ionization chamber traceable to its primary standard to the PTB for calibration in 60Co and in linac beams and PTB sent a PTW 31010 ionization chamber traceable to its primary standard to LNE-LNHB for calibration in 60Co and in linac beams. Calculated Sw,air will be used as beam quality specifier for the ionization chamber comparison at different field sizes. The standard uncertainties (k = 1) of PTB and LNE-LNHB calibration coefficients lie respectively between 0.25% (60Co) and 0.40% (linac) and between 0.29% and 0.46%. PTB and LNE-LNHB absorbed-dose-to-water references developed for this project, based respectively on water calorimetry and on graphite calorimetry, agree within 1.5 standard deviations for field size of 10 cm × 10 cm down to 2 cm × 2 cm and for beams of 6 MV to 10 MV.

MCNP6 model of the University of Washington clinical neutron therapy system (CNTS).

PubMed

Moffitt, Gregory B; Stewart, Robert D; Sandison, George A; Goorley, John T; Argento, David C; Jevremovic, Tatjana

2016-01-21

A MCNP6 dosimetry model is presented for the Clinical Neutron Therapy System (CNTS) at the University of Washington. In the CNTS, fast neutrons are generated by a 50.5 MeV proton beam incident on a 10.5 mm thick Be target. The production, scattering and absorption of neutrons, photons, and other particles are explicitly tracked throughout the key components of the CNTS, including the target, primary collimator, flattening filter, monitor unit ionization chamber, and multi-leaf collimator. Simulations of the open field tissue maximum ratio (TMR), percentage depth dose profiles, and lateral dose profiles in a 40 cm × 40 cm × 40 cm water phantom are in good agreement with ionization chamber measurements. For a nominal 10 × 10 field, the measured and calculated TMR values for depths of 1.5 cm, 5 cm, 10 cm, and 20 cm (compared to the dose at 1.7 cm) are within 0.22%, 2.23%, 4.30%, and 6.27%, respectively. For the three field sizes studied, 2.8 cm × 2.8 cm, 10.4 cm × 10.3 cm, and 28.8 cm × 28.8 cm, a gamma test comparing the measured and simulated percent depth dose curves have pass rates of 96.4%, 100.0%, and 78.6% (depth from 1.5 to 15 cm), respectively, using a 3% or 3 mm agreement criterion. At a representative depth of 10 cm, simulated lateral dose profiles have in-field (⩾ 10% of central axis dose) pass rates of 89.7% (2.8 cm × 2.8 cm), 89.6% (10.4 cm × 10.3 cm), and 100.0% (28.8 cm × 28.8 cm) using a 3% and 3 mm criterion. The MCNP6 model of the CNTS meets the minimum requirements for use as a quality assurance tool for treatment planning and provides useful insights and information to aid in the advancement of fast neutron therapy.

Critical current enhancement by neutron irradiation of rapidly textured Bi[sub 2]Sr[sub 2]CaCu[sub 2]O[sub 8

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kramer, M.J.; Arrasmith, S.R.; McCallum, R.W.

1992-08-24

We have investigated the effect of fast neutron irradiation on c-axis aligned Bi[sub 2]Sr[sub 2]CaCU[sub 2]O[sub 8] (Bi2212) produced using a new technique. Amorphous Bi2212 was crystallized under 20 MPa uniaxial stress at 870[degree]C for 6 hrs. DC SQUID shows a transition onset of 90K. Material was cut into 2 [times] 2 [times] 0.150 mm slabs, sealed in quartz ampules, and irradiated at fluences of 10[sup 16], 5 [times] 10[sup 16], 2.5 [times] l0[sup 17], and 7.2 [times] 10[sup l7] n/cm[sup 2]. DC SQUID results show that J[sub c] is increased by a factor of 2.5 at 10K for fluencesmore » of 7.2 [times] l0[sup 17] for H parallel to c-axis for fields less than 3 T. The higher the fluence, the lower the dependency of J[sub c] on applied field and temperature. T[sub c] decreased by 1 K for a fluence of 2..5 [times] l0[sup 17] n/cm[sup 2] with an additional 2 K drop for 7.2 [times] l0[sup 17] n/cm[sup 2]. The increase in the width of the high field hysteresis loops for increasing fluence is more pronounced for samples measured normal to the c-axis.« less

Critical current enhancement by neutron irradiation of rapidly textured Bi{sub 2}Sr{sub 2}CaCu{sub 2}O{sub 8}

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kramer, M.J.; Arrasmith, S.R.; McCallum, R.W.

1992-08-24

We have investigated the effect of fast neutron irradiation on c-axis aligned Bi{sub 2}Sr{sub 2}CaCU{sub 2}O{sub 8} (Bi2212) produced using a new technique. Amorphous Bi2212 was crystallized under 20 MPa uniaxial stress at 870{degree}C for 6 hrs. DC SQUID shows a transition onset of 90K. Material was cut into 2 {times} 2 {times} 0.150 mm slabs, sealed in quartz ampules, and irradiated at fluences of 10{sup 16}, 5 {times} 10{sup 16}, 2.5 {times} l0{sup 17}, and 7.2 {times} 10{sup l7} n/cm{sup 2}. DC SQUID results show that J{sub c} is increased by a factor of 2.5 at 10K for fluencesmore » of 7.2 {times} l0{sup 17} for H parallel to c-axis for fields less than 3 T. The higher the fluence, the lower the dependency of J{sub c} on applied field and temperature. T{sub c} decreased by 1 K for a fluence of 2..5 {times} l0{sup 17} n/cm{sup 2} with an additional 2 K drop for 7.2 {times} l0{sup 17} n/cm{sup 2}. The increase in the width of the high field hysteresis loops for increasing fluence is more pronounced for samples measured normal to the c-axis.« less

Integrating auxiliary data and geophysical techniques for the estimation of soil clay content using CHAID algorithm

NASA Astrophysics Data System (ADS)

Abbaszadeh Afshar, Farideh; Ayoubi, Shamsollah; Besalatpour, Ali Asghar; Khademi, Hossein; Castrignano, Annamaria

2016-03-01

This study was conducted to estimate soil clay content in two depths using geophysical techniques (Ground Penetration Radar-GPR and Electromagnetic Induction-EMI) and ancillary variables (remote sensing and topographic data) in an arid region of the southeastern Iran. GPR measurements were performed throughout ten transects of 100 m length with the line spacing of 10 m, and the EMI measurements were done every 10 m on the same transect in six sites. Ten soil cores were sampled randomly in each site and soil samples were taken from the depth of 0-20 and 20-40 cm, and then the clay fraction of each of sixty soil samples was measured in the laboratory. Clay content was predicted using three different sets of properties including geophysical data, ancillary data, and a combination of both as inputs to multiple linear regressions (MLR) and decision tree-based algorithm of Chi-Squared Automatic Interaction Detection (CHAID) models. The results of the CHAID and MLR models with all combined data showed that geophysical data were the most important variables for the prediction of clay content in two depths in the study area. The proposed MLR model, using the combined data, could explain only 0.44 and 0.31% of the total variability of clay content in 0-20 and 20-40 cm depths, respectively. Also, the coefficient of determination (R2) values for the clay content prediction, using the constructed CHAID model with the combined data, was 0.82 and 0.76 in 0-20 and 20-40 cm depths, respectively. CHAID models, therefore, showed a greater potential in predicting soil clay content from geophysical and ancillary data, while traditional regression methods (i.e. the MLR models) did not perform as well. Overall, the results may encourage researchers in using georeferenced GPR and EMI data as ancillary variables and CHAID algorithm to improve the estimation of soil clay content.

Effects of ion doping at different sites on electrical properties of multiferroic BiFeO3 ceramics

NASA Astrophysics Data System (ADS)

Yu, Benfang; Li, Meiya; Liu, Jun; Guo, Dongyun; Pei, Ling; Zhao, Xingzhong

2008-03-01

Pure, La3+ doped at A site, V5+ doped at B site, and La3+ and V5+ co-doped multiferroic BiFeO3 ceramics: BiFeO3 (BFO), Bi0.85La0.15FeO3 (BLF), BiFe0.97V0.03O3 (BFV), Bi0.85La0.15Fe0.97V0.03O3 (BLFV), etc were successfully prepared by a rapid liquid sintering technique. X-ray diffraction indicated that these ceramics were of polycrystalline perovskite structures, accompanied with a tiny residual Bi2O3 phase. It was found that, among these ceramics, BLFV ceramic exhibited the best electrical properties. The leakage current density of BLFV ceramic was only 2.1 × 10-6 A cm-2 at 10 kV cm-1, two and one orders of magnitude lower than those of the BLF and BFV ceramics, respectively. In the measuring frequency of 4 KHz-1 MHz, the dielectric constants and losses of this sample exhibited slight variation and the lowest loss tangent was 0.08. The sample had a relatively saturated ferroelectric hysteresis loop. These suggested that the co-doped BiFeO3 ceramic by La3+ and V5+ at A and B sites showed advantages in application over the pure BFO, doped BLF and BFV ceramics, respectively.

[Application of injection test in confirming the ideal position of esophageal balloon catheter].

PubMed

Chen, Han; Xu, Ming; Yang, Yanlin; He, Xuan; Zhou, Jianxin

2017-09-01

To evaluate the safety and feasibility of injection test which is used to locate esophageal balloon catheter. A prospective study was conducted. The patients undergoing invasive mechanical ventilation (MV) admitted to general intensive care unit (ICU) of Beijing Tiantan Hospital Affiliated to Capital Medical University from May 2015 and March 2017 were enrolled. The commercially available esophageal balloon catheter was modified to perform injection test. The catheter was withdrawn step by step and the injection test was repeated until the presence disturbance wave presented, which indicated that the balloon had just entered the esophagus. The position where disturbance wave appears was named 0 cm. End-expiratory occlusions were performed at the positions of +15, +10, +5, 0, -5, -10 and -15 cm, respectively, and the changes of esophageal pressure (Pes) and airway pressures (Paw) were measured in the spontaneous breathing and passive ventilation, and the ratio between the changes (ΔPes/ΔPaw) was calculated. A total of 20 patients were enrolled, of which 15 patients finished both the spontaneous and the passive ventilation parts, and 2 patients finished only the spontaneous part and 3 patients finished only passive part. (1) Disturbance waves could be induced by injection test in all patients. The average depth of disturbance wave in spontaneous breathing was deeper than that in passive ventilation (cm: 42.4±3.8 vs. 41.8±3.3), but there was no significant difference between the two ventilation settings (P = 0.132). No adverse events occurred during the study period. (2) Pes increased with the stepwise withdraw of esophageal catheter, reached the maximal value at +5 cm, and then decreased when the catheter was further withdrawn, no matter in the spontaneous or the passive ventilation. In spontaneous breathing, the ΔPes/ΔPaw was within the ideal range (0.8-1.2) at the positions of 0, -5 and -10 cm. The ΔPes/ΔPaw was closest to unity at the positions of 0 cm (0.98±0.15). The ΔPes/ΔPaw at -15 cm (0.66±0.26) was significantly lower than that at 0 cm (P < 0.05). For passive ventilation, the ΔPes/ΔPaw was within the ideal range at the positions of -5 cm and -10 cm, and the ΔPes/ΔPaw was closest to unity at the positions of -10 cm (0.94±0.12). The ΔPes/ΔPaw at 0 cm and -5 cm was significantly higher than that at -10 cm (1.43±0.31 and 1.12±0.14, respectively); while the ΔPes/ΔPaw at -15 cm (0.68±0.23) was significantly lower than that at -10 cm (all P < 0.01). Ideal position of the esophageal balloon catheter could be determined quickly and easily by using injection test. The method is safe and clinically feasible. Clinical Trials, NCT02446938.

Molecular approaches to p- and n-nanoscale doping of Ge 1-ySn y semiconductors: Structural, electrical and transport properties

NASA Astrophysics Data System (ADS)

Xie, Junqi; Tolle, J.; D'Costa, V. R.; Weng, C.; Chizmeshya, A. V. G.; Menendez, J.; Kouvetakis, J.

2009-08-01

We report the development of practical doping protocols via designer molecular sources to create n- and p-type doped Ge 1-ySn y layers grown directly upon Si(1 0 0). These materials will have applications in the fabrication of advanced PIN devices that are intended to extend the infrared optical response beyond that of Ge by utilizing the Sn composition as an additional design parameter. Highly controlled and efficient n-doping of single-layer structures is achieved using custom built P(GeH 3) 3 and As(GeH 3) 3, precursors containing preformed Ge-As and Ge-P near-tetrahedral bonding arrangements compatible with the structure of the host Ge-Sn lattice. Facile substitution and complete activation of the P and As atoms at levels ˜10 17-10 19 cm -3 is obtained via in situ depositions at low temperatures (350 °C). Acceptor doping is readily achieved using conventional diborane yielding carrier concentrations between 10 17-10 19 cm -3 under similar growth conditions. Full activation of the as-grown dopant concentrations is demonstrated by combined SIMS and Hall experiments, and corroborated using a contactless spectroscopic ellipsometry approach. RTA processing of the samples leads to a significant increase in carrier mobility comparable to that of bulk Ge containing similar doping levels. The alloy scattering contribution appears to be negligible for electron carrier concentrations beyond 10 19 cm -3 in n-type samples and hole concentrations beyond 10 18 cm -3 in p-type samples. A comparative study using the classical lower-order hydrides PH 3 and AsH 3 produced n-doped films with carrier densities (up to 9 × 10 19 cm -3) similar to those afforded by P(GeH 3) 3 and As(GeH 3) 3. However, early results indicate that the simpler PH 3 and AsH 3 sources yield materials with inferior morphology and microstructure. Calculations of surface energetics using bond enthalpies suggest that the latter massive compounds bind to the surface via strong Ge-Ge bonds and likely act as "retardants" that moderate surface diffusion of the reactions species, thereby promoting layer-by-layer growth leading to thick, atomically smooth films, particularly in the case of P(GeH 3) 3. Furthermore, the intact incorporation of the Ge 3P and Ge 3As molecular cores results in highly uniform compositional, strain and doping profiles at the atomic level.

Mechanical properties of carbon steel depending on the rate of the dose build-up of nitrogen and argon ions

NASA Astrophysics Data System (ADS)

Vorob'ev, V. L.; Bykov, P. V.; Bayankin, V. Ya.; Shushkov, A. A.; Vakhrushev, A. V.

2014-08-01

The effect of pulsed irradiation with argons and nitrogen ions on the mechanical properties, morphology, and structure of the surface layers of carbon steel St3 (0.2% C, 0.4% Mn, 0.15% Si, and Fe for balance) has been investigated depending on the rate of dose build-up at an average ion current density of 10, 20, and 40 μA/cm2. It has been established that the fatigue life and microhardness of surface layers increase in the entire studied range of dose build-up rates. This seems to be due to the hardening of the surface layers, which resulted from the generation of radiation defects and the irradiation-dynamic effect of fast ions. The sample irradiated by argon ions at the lowest of the selected dose build-up rates j av = 10 μA/cm2 withstands the largest number of cycles to failure.

LASER APPLICATIONS AND OTHER TOPICS IN QUANTUM ELECTRONICS: Optoelectronic switching in diamond and optical surface breakdown

NASA Astrophysics Data System (ADS)

Lipatov, E. I.; Tarasenko, V. F.

2008-03-01

The optoelectronic switching in two natural diamond samples of type 2-A is studied at voltages up to 1000 V and the energy density of control 60-ns, 308-nm laser pulses up to 0.6 J cm-2. It is shown that the design of a diamond switch affects the switching efficiency. When the energy density exceeds 0.2 J cm-2 and the interelectrode surface is completely illuminated, the surface breakdown is initiated by UV radiation, which shunts the current flow through the diamond crystal. When the illumination of the interelectrode surface is excluded, the surface breakdown does not occur. The threshold radiation densities sufficient for initiating the surface breakdown are determined for electric field strengths up to 10 kV cm-1.

Concurrent measurements of size-segregated particulate sulfate, nitrate and ammonium using quartz fiber filters, glass fiber filters and cellulose membranes

NASA Astrophysics Data System (ADS)

Tian, Shili; Pan, Yuepeng; Wang, Jian; Wang, Yuesi

2016-11-01

Current science and policy requirements have focused attention on the need to expand and improve particulate matter (PM) sampling methods. To explore how sampling filter type affects artifacts in PM composition measurements, size-resolved particulate SO42-, NO3- and NH4+ (SNA) were measured on quartz fiber filters (QFF), glass fiber filters (GFF) and cellulose membranes (CM) concurrently in an urban area of Beijing on both clean and hazy days. The results showed that SNA concentrations in most of the size fractions exhibited the following patterns on different filters: CM > QFF > GFF for NH4+; GFF > QFF > CM for SO42-; and GFF > CM > QFF for NO3-. The different patterns in coarse particles were mainly affected by filter acidity, and that in fine particles were mainly affected by hygroscopicity of the filters (especially in size fraction of 0.65-2.1 μm). Filter acidity and hygroscopicity also shifted the peaks of the annual mean size distributions of SNA on QFF from 0.43-0.65 μm on clean days to 0.65-1.1 μm on hazy days. However, this size shift was not as distinct for samples measured with CM and GFF. In addition, relative humidity (RH) and pollution levels are important factors that can enhance particulate size mode shifts of SNA on clean and hazy days. Consequently, the annual mean size distributions of SNA had maxima at 0.65-1.1 μm for QFF samples and 0.43-0.65 μm for GFF and CM samples. Compared with NH4+ and SO42-, NO3- is more sensitive to RH and pollution levels, accordingly, the annual mean size distribution of NO3- exhibited peak at 0.65-1.1 μm for CM samples instead of 0.43-0.65 μm. These methodological uncertainties should be considered when quantifying the concentrations and size distributions of SNA under different RH and haze conditions.

Combined reactor neutron beam and {sup 60}Co γ-ray radiation effects on CMOS APS image sensors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Zujun, E-mail: wangzujun@nint.ac.cn; Chen, Wei; Sheng, Jiangkun

The combined reactor neutron beam and {sup 60}Co γ-ray radiation effects on complementary metal-oxide semiconductor (CMOS) active pixel sensors (APS) have been discussed and some new experimental phenomena are presented. The samples are manufactured in the standard 0.35-μm CMOS technology. Two samples were first exposed to {sup 60}Co γ-rays up to the total ionizing dose (TID) level of 200 krad(Si) at the dose rates of 50.0 and 0.2 rad(Si)/s, and then exposed to neutron fluence up to 1 × 10{sup 11} n/cm{sup 2} (1-MeV equivalent neutron fluence). One sample was first exposed to neutron fluence up to 1 × 10{supmore » 11} n/cm{sup 2} (1-MeV equivalent neutron fluence), and then exposed to {sup 60}Co γ-rays up to the TID level of 200 krad(Si) at the dose rate of 0.2 rad(Si)/s. The mean dark signal (K{sub D}), the dark signal non-uniformity (DSNU), and the noise (V{sub N}) versus the total dose and neutron fluence has been investigated. The degradation mechanisms of CMOS APS image sensors have been analyzed, especially for the interaction induced by neutron displacement damage and TID damage.« less

High energy storage density over a broad temperature range in sodium bismuth titanate-based lead-free ceramics.

PubMed

Yang, Haibo; Yan, Fei; Lin, Ying; Wang, Tong; Wang, Fen

2017-08-18

A series of (1-x)Bi 0.48 La 0.02 Na 0.48 Li 0.02 Ti 0.98 Zr 0.02 O 3 -xNa 0.73 Bi 0.09 NbO 3 ((1-x)LLBNTZ-xNBN) (x = 0-0.14) ceramics were designed and fabricated using the conventional solid-state sintering method. The phase structure, microstructure, dielectric, ferroelectric and energy storage properties of the ceramics were systematically investigated. The results indicate that the addition of Na 0.73 Bi 0.09 NbO 3 (NBN) could decrease the remnant polarization (P r ) and improve the temperature stability of dielectric constant obviously. The working temperature range satisfying TCC 150  °C  ≤±15% of this work spans over 400 °C with the compositions of x ≥ 0.06. The maximum energy storage density can be obtained for the sample with x = 0.10 at room temperature, with an energy storage density of 2.04 J/cm 3 at 178 kV/cm. In addition, the (1-x)LLBNTZ-xNBN ceramics exhibit excellent energy storage properties over a wide temperature range from room temperature to 90 °C. The values of energy storage density and energy storage efficiency is 0.91 J/cm 3 and 79.51%, respectively, for the 0.90LLBNTZ-0.10NBN ceramic at the condition of 100 kV/cm and 90 °C. It can be concluded that the (1-x)LLBNTZ-xNBN ceramics are promising lead-free candidate materials for energy storage devices over a broad temperature range.

Relativistic high-current electron-beam stopping-power characterization in solids and plasmas: collisional versus resistive effects.

PubMed

Vauzour, B; Santos, J J; Debayle, A; Hulin, S; Schlenvoigt, H-P; Vaisseau, X; Batani, D; Baton, S D; Honrubia, J J; Nicolaï, Ph; Beg, F N; Benocci, R; Chawla, S; Coury, M; Dorchies, F; Fourment, C; d'Humières, E; Jarrot, L C; McKenna, P; Rhee, Y J; Tikhonchuk, V T; Volpe, L; Yahia, V

2012-12-21

We present experimental and numerical results on intense-laser-pulse-produced fast electron beams transport through aluminum samples, either solid or compressed and heated by laser-induced planar shock propagation. Thanks to absolute K(α) yield measurements and its very good agreement with results from numerical simulations, we quantify the collisional and resistive fast electron stopping powers: for electron current densities of ≈ 8 × 10(10) A/cm(2) they reach 1.5 keV/μm and 0.8 keV/μm, respectively. For higher current densities up to 10(12)A/cm(2), numerical simulations show resistive and collisional energy losses at comparable levels. Analytical estimations predict the resistive stopping power will be kept on the level of 1 keV/μm for electron current densities of 10(14)A/cm(2), representative of the full-scale conditions in the fast ignition of inertially confined fusion targets.

Global Active Stretching (SGA®) Practice for Judo Practitioners’ Physical Performance Enhancement

PubMed Central

ALMEIDA, HELENO; DE SOUZA, RAPHAEL F.; AIDAR, FELIPE J.; DA SILVA, ALISSON G.; REGI, RICARDO P.; BASTOS, AFRÂNIO A.

2018-01-01

In order to analyze the Global Active Stretching (SGA®) practice on the physical performance enhancement in judo-practitioner competitors, 12 male athletes from Judo Federation of Sergipe (Federação Sergipana de Judô), were divided into two groups: Experimental Group (EG) and Control Group (CG). For 10 weeks, the EG practiced SGA® self-postures and the CG practiced assorted calisthenic exercises. All of them were submitted to a variety of tests (before and after): handgrip strength, flexibility, upper limbs’ muscle power, isometric pull-up force, lower limbs’ muscle power (squat-jump – SJ and countermovement jump – CMJ) and Tokui Waza test. Due to the small number of people in the sample, the data were considered non-parametric and then we applied the Wilcoxon test using the software R version 3.3.2 (R Development Core Team, Austria). The effect size was calculated and considered statistically significant the values p ≤ 0.05. Concerning the results, the EG statistical differences were highlighted in flexibility, upper limbs’ muscle power and lower limbs’ muscle power (CMJ), with a gain of 3.00 ± (1.09) cm, 0,42 ± (0,51) m and 2.49 ± (0.63) cm, respectively. The CG only presented statistical difference in the lower limbs’ test (CMJ), with a gain of 0,55 ± 2,28 cm. Thus, the main results pointed out statistical differences before and after in the EG in the flexibility, upper limbs and lower limbs’ muscle power (CMJ), with a gain of 3.00 ± 1.09 cm, 0.42 ± 0.51 m 2.49 ± 0.63 cm, respectively. On the other hand, the CG presented a statistical difference only the lower limbs’ CMJ test, with a gain of 0.55 ± 2.28 cm. The regular 10-week practice of SGA® self-postures increased judoka practitioners’ posterior chain flexibility and vertical jumping (CMJ) performance. PMID:29795746

Heavy ion irradiations on synthetic hollandite-type materials: Ba1.0Cs0.3A2.3Ti5.7O16 (A=Cr, Fe, Al)

NASA Astrophysics Data System (ADS)

Tang, Ming; Tumurugoti, Priyatham; Clark, Braeden; Sundaram, S. K.; Amoroso, Jake; Marra, James; Sun, Cheng; Lu, Ping; Wang, Yongqiang; Jiang, Ying.-Bing.

2016-07-01

The hollandite supergroup of minerals has received considerable attention as a nuclear waste form for immobilization of Cs. The radiation stability of synthetic hollandite-type compounds described generally as Ba1.0Cs0.3A2.3Ti5.7O16 (A=Cr, Fe, Al) were evaluated by heavy ion (Kr) irradiations on polycrystalline single phase materials and multiphase materials incorporating the hollandite phases. Ion irradiation damage effects on these samples were examined using grazing incidence X-ray diffraction (GIXRD) and transmission electron microscopy (TEM). Single phase compounds possess tetragonal structure with space group I4/m. GIXRD and TEM observations revealed that 600 keV Kr irradiation-induced amorphization on single phase hollandites compounds occurred at a fluence between 2.5×1014 Kr/cm2 and 5×1014 Kr/cm2. The critical amorphization fluence of single phase hollandite compounds obtained by in situ 1 MeV Kr ion irradiation was around 3.25×1014 Kr/cm2. The hollandite phase exhibited similar amorphization susceptibility under Kr ion irradiation when incorporated into a multiphase system.

Terahertz cyclotron resonance spectroscopy of an AlGaN/GaN heterostructure using a high-field pulsed magnet and an asynchronous optical sampling technique

DOE Office of Scientific and Technical Information (OSTI.GOV)

Spencer, B. F., E-mail: Ben.Spencer@manchester.ac.uk; Smith, W. F.; Hibberd, M. T.

2016-05-23

The effective mass, sheet carrier concentration, and mobility of electrons within a two-dimensional electron gas in an AlGaN/GaN heterostructure were determined using a laboratory-based terahertz cyclotron resonance spectrometer. The ability to perform terahertz cyclotron resonance spectroscopy with magnetic fields of up to 31 T was enabled by combining a high-field pulsed magnet with a modified asynchronous optical sampling terahertz detection scheme. This scheme allowed around 100 transmitted terahertz waveforms to be recorded over the 14 ms magnetic field pulse duration. The sheet density and mobility were measured to be 8.0 × 10{sup 12 }cm{sup −2} and 9000 cm{sup 2} V{sup −1} s{sup −1} at 77 K. The in-planemore » electron effective mass at the band edge was determined to be 0.228 ± 0.002m{sub 0}.« less

Characterization of exposure to carbon nanotubes in an industrial setting.

PubMed

Fonseca, Ana Sofia; Viitanen, Anna-Kaisa; Koivisto, Antti J; Kangas, Annelli; Huhtiniemi, Marika; Hussein, Tareq; Vanhala, Esa; Viana, Mar; Querol, Xavier; Hämeri, Kaarle

2015-06-01

While production and use of carbon nanotubes (CNTs) is increasing, workers exposure to CNTs is expected to increase as well, with inhalation being potentially the main pathway for uptake. However, there have been few studies reporting results about workers' personal exposure to CNTs. In this study, worker exposure to single-walled CNTs (SWCNTs) during the production of conductive films in a modern up-scaling factory was assessed. Particulate matter concentrations (2.5-10 μm) and concentrations of CO and CO2 were monitored by using real-time instruments. Workers' exposure levels to SWCNTs were qualitatively estimated by analyzing particle samples by transmission electron microscopy (TEM). TEM samples identified high aspect ratio (length/width > 500) SWCNTs in workplace air. SWCNT concentrations estimated from micrographs varied during normal operation, reactor use without local exhaust ventilation (LEV), and cleaning between 1.7×10(-3), 5.6 and 6.0×10(-3) SWCNT cm(-3), respectively. However, during cleaning it was unclear whether the SWCNTs originated from the cleaning itself or from other reactor openings. We were unable to quantify the SWCNT emissions with online particle instrumentation due to the SWCNT low concentrations compared to background particle concentrations, which were on average 2.6±1.1×10(3)cm(-3). However, CO concentrations were verified as a good indicator of fugitive emissions of SWCNTs. During normal operation, exposure levels were well below proposed limit values (1.0×10(-2) fibers cm(-3) and 1 µg m(-3)) when LEV was used. Based on the results in this study, the analysis of TEM grids seems to be the only direct method to detect SWCNTs in workplace air. © The Author 2014. Published by Oxford University Press on behalf of the British Occupational Hygiene Society.

Enhancement of the critical current density and flux pinning of MgB2 superconductor by nanoparticle SiC doping

NASA Astrophysics Data System (ADS)

Dou, S. X.; Soltanian, S.; Horvat, J.; Wang, X. L.; Zhou, S. H.; Ionescu, M.; Liu, H. K.; Munroe, P.; Tomsic, M.

2002-10-01

Doping of MgB2 by nano-SiC and its potential for the improvement of flux pinning were studied for MgB2-x)(SiCx/2 with x=0, 0.2, and 0.3 and for 10 wt % nano-SiC-doped MgB2 samples. Cosubstitution of B by Si and C counterbalanced the effects of single-element doping, decreasing Tc by only 1.5 K, introducing intragrain pinning centers effective at high fields and temperatures, and significantly enhancing Jc and Hirr. Compared to the undoped sample, Jc for the 10 wt % doped sample increased by a factor of 32 at 5 K and 8 T, 42 at 20 K and 5 T, and 14 at 30 K and 2 T. At 20 K and 2 T, the Jc for the doped sample was 2.4 x105 A/cm2, which is comparable to Jc values for the best Ag/Bi-2223 tapes. At 20 K and 4 T, Jc was twice as high as for the best MgB2 thin films and an order of magnitude higher than for the best Fe/MgB2 tapes. The magnetic Jc is consistent with the transport Jc which remains at 20 000 A/cm2 even at 10 T and 5 K for the doped sample, an order of magnitude higher than the undoped one. Because of such high performance, it is anticipated that the future MgB2 conductors will be made using a formula of MgBxSiyCz instead of pure MgB2.

Ferroelectric PLZT thick films grown by poly(1-vinylpyrrolidone-co-vinyl acetate) (PVP/VA)-modified sol-gel process

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hu, Zhongqiang; Ma, Beihai; Li, Meiya

2016-03-01

We report the growth of ferroelectric Pb0.92La0.08Zr0.52Ti0.48O3 (PLZT) thick films using a poly(1-vinylpyrrolidone-co-vinyl acetate) (PVP/VA)-modified sol–gel process. A per-coating thickness of ≈0.66 μm has been demonstrated using PVP/VA-modified solution, which is more than doubled that of the PLZT films grown by PVP-modified method, and nearly 6 times the per-coating thickness of films prepared by conventional sol–gel process. PLZT thick films grown on LNO/Ni substrates exhibited denser microstructure, higher remanent polarization (11 μC/cm 2) and dielectric tunability (45%), lower leakage current density (≈1.2 × 10 -8 A/cm 2), and higher breakdown strength (≈1.6 MV/cm) than those for the samples grown onmore » PtSi substrates. These results demonstrated great potential of using PVP/VA-modified sol–gel process for high power film capacitor applications.« less

Collision induced broadening and shifting of the H and K lines of Ca+ at low temperature

NASA Astrophysics Data System (ADS)

Wang, Xin; Zhang, Rui; Shen, Yong; Liu, Qu; Zou, Hongxin; Yan, Bing

2017-09-01

Multireference configuration interaction method was used to compute the potential energy curves of Λ-S states correlating with lowest three atomic limits in Ca+-He molecular collision system. The potential energy curves of nine Ω states were obtained with inclusion of spin-orbit coupling. And the electric dipole and quadrupole moment matrix elements between excited states and ground state were also computed. Furthermore, with aid of the Anderson-Talman theory we calculated the broadening and shifting coefficients for Ca+-He spectral lines in the low temperature regime. For H line, α = 0.303 × 10-20 cm-1/cm-3, β = -0.0527 × 10-20cm-1/cm-3; For K line, α = 0.233 × 10-20cm-1/cm-3, β = -0.0402 × 10-20cm-1/cm-3 These results are helpful to understand the collision effects induced by He atom in further spectra investigations of cold Ca+ ions.

[Nitrogen mineralization rate in different soil layers and its influence factors under plastic film mulched in Danjiangkou Reservoir area, China].

PubMed

Yu, Xing Xiu; Xui, Miao Miao; Zhao, Jin Hui; Zhang, Jia Peng; Wang, Wei; Guo, Ya Li; Xiao, Juan Hua

2018-04-01

The objective of this study was to investigate the rate of nitrogen mineralization in various soil layers (0-10, 10-20, and 20-30 cm) and its influencing factors under plastic film mulching ridge-furrow in a corn field of Wulongchi small watershed, Danjiangkou Reservoir Area. Results showed that the rate of soil ammonification decreased with soil depth during the entire maize growth period. The rate of nitrification in seedling, jointing, and heading stages decreased in the following order: 10-20 cm > 0-10 cm > 20-30 cm, while it increased with soil depth in maturation stage. The rate of soil nitrogen mineralization decreased with the increases in soil depth in the seedling, jointing and heading stages, whereas an opposite pattern was observed in maturation stage. Compared with non-filming, film mulching promoted the soil ammonification process in 0-10 cm and the soil nitrification and nitrogen mineralization processes in jointing, heading, and maturation stages in both 0-10 and 10-20 cm. However, the rates of soil nitrification and nitrogen mineralization under film mulching were much lower than those under non-filming in seedling stage. The stepwise regression analysis indicated that the main factors influencing soil nitrogen mineralization rate varied with soil depth. Soil moisture and total N content were the dominant controller for variation of soil nitrogen mineralization in 0-10 cm layer. Soil temperature, moisture, and total N content were dominant controller for that in 10-20 cm layer. Soil temperature drove the variation of soil nitrogen mineralization in 20-30 cm layer.

Tailoring of the titanium surface by preparing cardiovascular endothelial extracellular matrix layer on the hyaluronic acid micro-pattern for improving biocompatibility.

PubMed

Li, Jingan; Zhang, Kun; Wu, Juejue; Zhang, Lijuan; Yang, Ping; Tu, Qiufen; Huang, Nan

2015-04-01

It has been proved that high molecular weight hyaluronic acid (HMW-HA, 1×10(6) Da) micro-strips on titanium (Ti) surface can elongate the human vascular endothelial cell (EC) morphology, subsequently enhance endothelial extracellular matrix (ECM) deposition in our previous work. The HMW-HA micro-strips were anticipated to possess good hemocompatibility and EC compatibility simultaneously. However, the single HMW-HA micro-strips on Ti substrate showed bad hemocompatibility. To solve this problem, a method combining HA micro-pattern and EC decellularization was developed, and the endothelial extracellular matrix layer on the HA micro-pattern (ECM/HAP) showed excellent hemocompatibility and endothelial progenitor cells (EPCs) compatibility (cell number: 14.3±0.5×10(5) cells/cm2>2.2±0.7×10(5) cells/cm2 on ECM/TiOH, 7.5±1.3×10(5) cells/cm2 on TiOH, 3.4±0.9×10(5) cells/cm2 on TiOH/HAP and 3.6±1.2×10(5) cells/cm2 on Ti). We also found that the ECM/HAP coating could significantly inhibit the excessive proliferation of smooth muscle cells (SMCs) (cck-8 absorption: 0.25±0.06<1.18±0.09 A.U. on ECM/TiOH, 0.87±0.15 A.U. on TiOH and 1.55±0.11 A.U. on Ti) and the attachment of macrophages (cell number: 1.3±0.1×10(3)<9.2±1.5×10(3) cells/cm2 on ECM/TiOH, 8.8±0.3×10(3) cells/cm2 on TiOH, 7.3±0.7×10(3) cells/cm2 on TiOH/HAP and 9.6±0.9×10(3) cells/cm2 on Ti in 12 h). These data suggest that the multifunctional ECM/HAP coating can be used to build the bionic human endothelial ECM on the biomaterials surface, which might provide a potential and effective method for surface modification of cardiovascular devices. Copyright © 2015. Published by Elsevier B.V.

Decline of the 2-10 keV Emission from Eta Carinae

NASA Technical Reports Server (NTRS)

Liburd, Jamar; Corcoran, Michael F.; Hamaguchi, Kenji; Gull, Theodore R.; Madura, Thomas; Teodoro, Mairan; Moffat, Anthony; Richardson, Noel; Russell, Chris; Pollock, Andrew;

Effect of Al substitution on the enhanced electrochemical performance and strong structure stability of Na3V2(PO4)3/C composite cathode for sodium-ion batteries

NASA Astrophysics Data System (ADS)

Chen, Yanjun; Xu, Youlong; Sun, Xiaofei; Wang, Chao

2018-01-01

In this study, a promising cathode material in Na-ion batteries, Al-doped NASICON-type Na3V2-xAlx(PO4)3/C (0 ≤ × ≤0.03) samples are synthesized and characterized. The doping effects on the crystal structure are investigated by XRD and XPS, indicating that low dose of Al3+ doping generates no damage on the structure of the material, and aluminum is substituted for the vanadium site successfully. Electron microscopy and Raman data show that amorphous carbon coated on the matrix can enhance the electron conductivity. The electrochemical kinetic response of Al3+ doping are tested based on "slow-charge and rapid-discharge" electrochemical mode, results from before and after the cycles show that the doping samples have strong structure stability and excellent electrochemical performance because of low internal resistances and high ion conductivity. Thus, Na3V1.98Al0.02(PO4)3/C exhibits an initial reversible capacity of 102.7 mAh g-1 at 10 mA g-1 in the potential range between 2.3 and 3.8 V and delivers a discharge value of 95 mAh g-1vs. 59.9 mAh g-1 of NVP/C at current density of 70 mA g-1 discharge after 50 cycles. The ionic conductivity of Na3V1.98Al0.02(PO4)3/C sample at 3.4 V after 50 cycles at 10 mA g-1 charge 200 mA g-1 discharge is 1.31 × 10-12 cm2s-1, four orders of magnitude higher than the undoped one(7.79 × 10-17 cm2s-1).

Thermodynamics of Silica Dissolution From In-situ Raman +Spectroscopy

NASA Astrophysics Data System (ADS)

Davis, M. K.; Fumagalli, P.; Stixrude, L. P.

2001-12-01

Solubilities of cations, such as silicon, in water strongly effect both the physical and thermodynamical properties of supercritical metamorphic fluids. Modeling the thermodynamics of fluid-rock interactions requires therefore a profound understanding of cation dissolution and aqueous speciation. In-situ Raman experiments of the silica-water system were performed in an externally heated Bassett-type diamond-anvil cell at the Department of Geological Sciences, University of Michigan. Natural quartz samples (from Owl Creek Mountains, Wyoming) were loaded in the sample chamber with de-ionized or spectrographic water. All experiments used doubly polished rhenium gaskets with a thickness of 200 μ m, diameter of 1.0 mm, and a 500 μ m drillhole for the sample chamber. Temperature was measured using K-type thermocouples wrapped around both the upper and lower diamond anvils. Pressures are obtained on the basis of the shift of the 464 cm-1 Raman mode of quartz. In-situ Raman spectra were collected from 250-1200 cm-1, focusing on the vibrational modes of aqueous silica species at temperatures up to 700 ° C and pressures up to 14 kbar. We observed Si-O stretching modes attributable to dimer (H6Si2O7, 965 cm-1) and monomer (H4SiO4, 771 cm-1) aqueous silica species. The relative intensities of these two bands as a function of isochoric heating place constraints on the energetics of the polymerization reaction, if we assume that the intensity ratio is linearly related to concentration ratio. We have been able to perform experiments along two different isochores (0.9 and 0.75 g/cm3, respectively) from which we are able to derive the enthalpy of reaction.

Influence of light curing and sample thickness on microhardness of a composite resin

PubMed Central

Aguiar, Flávio HB; Andrade, Kelly RM; Leite Lima, Débora AN; Ambrosano, Gláucia MB; Lovadino, José R

2009-01-01

The aim of this in vitro study was to evaluate the influence of light-curing units and different sample thicknesses on the microhardness of a composite resin. Composite resin specimens were randomly prepared and assigned to nine experimental groups (n = 5): considering three light-curing units (conventional quartz tungsten halogen [QTH]: 550 mW/cm2 – 20 s; high irradiance QTH: 1160 mW/cm2 – 10 s; and light-emitting diode [LED]: 360 mW/cm2 – 40 s) and three sample thicknesses (0.5 mm, 1 mm, and 2 mm). All samples were polymerized with the light tip 8 mm away from the specimen. Knoop microhardness was then measured on the top and bottom surfaces of each sample. The top surfaces, with some exceptions, were almost similar; however, in relation to the bottom surfaces, statistical differences were found between curing units and thicknesses. In all experimental groups, the 0.5-mm-thick increments showed microhardness values statistically higher than those observed for 1- and -2-mm increments. The conventional and LED units showed higher hardness mean values and were statistically different from the high irradiance unit. In all experimental groups, microhardness mean values obtained for the top surface were higher than those observed for the bottom surface. In conclusion, higher levels of irradiance or thinner increments would help improve hybrid composite resin polymerization. PMID:23674901

Strongly enhanced current densities in Sr0.6K0.4Fe2As2 + Sn superconducting tapes.

PubMed

Lin, He; Yao, Chao; Zhang, Xianping; Zhang, Haitao; Wang, Dongliang; Zhang, Qianjun; Ma, Yanwei; Awaji, Satoshi; Watanabe, Kazuo

2014-03-25

Improving transport current has been the primary topic for practical application of superconducting wires and tapes. However, the porous nature of powder-in-tube (PIT) processed iron-based tapes is one of the important reasons for low critical current density (Jc) values. In this work, the superconducting core density of ex-situ Sr0.6K0.4Fe2As2 + Sn tapes, prepared from optimized precursors, was significantly improved by employing a simple hot pressing as an alternative route for final sintering. The resulting samples exhibited optimal critical temperature (Tc), sharp resistive transition, small resistivity and high Vickers hardness (Hv) value. Consequently, the transport Jc reached excellent values of 5.1 × 10(4) A/cm(2) in 10 T and 4.3 × 10(4) A/cm(2) in 14 T at 4.2 K, respectively. Our tapes also exhibited high upper critical field Hc2 and almost field-independent Jc. These results clearly demonstrate that PIT pnictide wire conductors are very promising for high-field magnet applications.

Reconstruction of the Exposure Histories of 20 Allan Hills Ordinary Chondrites on the Basis of Cosmogenic 10Be, 26Al, Noble Gases, and Cosmic Ray Tracks

NASA Astrophysics Data System (ADS)

Neupert, U.; Knauer, M.; Michel, R.; Loeken, Th.; Schultz, L.; Dittrich-Hannen, B.; Suter, M.; Kubik, P. W.; Metzler, K.; Romstedt, J.

1995-09-01

Twenty ordinary chondrites from the 1988/89 meteorite search (ALH 88004, 88008, 88010, 88011, 88013, 88016 to 88021, 88026 to 88031, 88033, 88039, 88042) [1,2] were investigated for 10Be and 26Al, and for He, Ne and Ar by accelerator and rare gas mass spectrometry, respectively. Cosmic ray tracks were measured in samples of ALH 88019. Using theoretical production rates calculated by a physical model [3] the experimental data are interpreted with respect to the reconstruction of the preatmospheric exposure conditions and exposure histories of the meteoroids. Ordinary chondrites are particularly well suited to exemplify the capabilities of an interpretation of many cosmogenic nuclides measured in one sample. Model calculations of GCR production rates were performed for 10Be, 26Al, 3He, 21Ne, 22Ne and 38Ar as reported elsewhere [4,5]. For all meteorites, except for ALH 88019, the cosmogenic nuclide data can be explained by simple one stage exposure histories between 3 Ma and 44 Ma in meteoroids with radii between 5 cm and 85 cm. Exposure ages were derived from cosmogenic 3He, 21Ne and 38Ar on the basis of the theoretical production rates as function of3He/21Ne and 22Ne/21Ne as well as on the empirical ones proposed by Eugster [6]. The average ratios of exposure ages determined from theoretical production rates to those calculated according to Eugster [6] were 1.08+/-0.11, 1.11+/-0.25 and 1.12+/-0.17 in case of 3He, 21Ne and 38Ar, respectively. Repeated measurements of 10Be and 26Al in ALH 88019 resulted in 10.4+/-1.3 dpm/kg and 5.6+/-0.5 dpm/kg, respectively. But, the cosmogenic rare gas concentrations point to a (single stage) exposure age of 39 Ma in a meteoroid. This is in accordance with a measured cosmic ray track density in olivine of 2.8 * 10^6 cm^-2. The samples are from depths betwen 3 cm and 8 cm. Based on the track data we obtain a minimum meteoroid radius of 8 cm. The low 10Be and 26Al cannot be explained by a one stage exposure history and a long terrestrial age. Possible other exposure scenarios are discussed. Using the theoretical 10Be production rates and the 3He/21Ne and 22Ne/21Ne ratios, constraints about the sizes of the meteoroids and about the shielding depths in the samples were derived. 26Al was not used for this purpose since in four meteorites it is evidently affected by SCR production and since, generally, it could be changed due to long terrestrial residence times. However, most of the observed 26Al concentrations which are not affected by SCR production are consistent within experimental uncertainties with the expected GCR production rates. Substantial terrestrial age are proposed for ALH 88008, ALH 88029 and ALH 88030. Pairing among the investigated meteorites is discussed on the basis of rare gas data, 10Be and 26Al, and NTL data by Benoit et al. [7,8]. It can be concluded that the 20 meteorites result from at least 16 different falls. Acknowledgement: This work was supported by the Deutsche Forschungsgemeinschaft and the Swiss National Science Foundation. References: [1] Meteoritical Bulletin (1990) Meteoritics, 25, 237. [2] Meteoritical Bulletin (1991) Meteoritics, 26, 68. [3] Michel R. et al. (1991) Meteoritics, 26, 221-242. [4] Michel R. et al. (1995) Planet. Space Sci., in press. [5] Herpers U. et al. (1995) Planet. Space Sci., in press. [6] Eugster O. (1988) GCA, 52, 1649-1662. [7] Benoit P. H. et al. (1991) Meteoritics, 26, 262. [8] Benoit P. H. et al. (1992) Meteoritics, 27, 110.

Potassium acceptor doping of ZnO crystals

DOE Office of Scientific and Technical Information (OSTI.GOV)

Parmar, Narendra S., E-mail: nparmar@wsu.edu; Lynn, K. G.; Department of Physics and Astronomy, Washington State University, Pullman, Washington 99164-2814

2015-05-15

ZnO bulk single crystals were doped with potassium by diffusion at 950°C. Positron annihilation spectroscopy confirms the filling of zinc vacancies and a different trapping center for positrons. Secondary ion mass spectroscopy measurements show the diffusion of potassium up to 10 μm with concentration ∼1 × 10{sup 16} cm{sup −3}. IR measurements show a local vibrational mode (LVM) at 3226 cm{sup −1}, at a temperature of 9 K, in a potassium doped sample that was subsequently hydrogenated. The LVM is attributed to an O–H bond-stretching mode adjacent to a potassium acceptor. When deuterium substitutes for hydrogen, a peak is observedmore » at 2378 cm{sup −1}. The O-H peak is much broader than the O-D peak, perhaps due to an unusually low vibrational lifetime. The isotopic frequency ratio is similar to values found in other hydrogen complexes. Potassium doping increases the resistivity up to 3 orders of magnitude at room temperature. The doped sample has a donor level at 0.30 eV.« less

The study of optical property of sapphire irradiated with 73 MeV Ca ions

NASA Astrophysics Data System (ADS)

Yang, Yitao; Zhang, Chonghong; Song, Yin; Gou, Jie; Liu, Juan; Xian, Yongqiang

2015-12-01

Single crystals of sapphire were irradiated with 73 MeV Ca ions at room temperature to the fluences of 0.1, 0.5 and 1.0 × 1014 ions/cm2. Optical properties of these samples were characterized by ultraviolet-visible spectrometry (UV-VIS) and fluorescence spectrometer (PL). In UV-VIS spectra, it is observed the absorbance bands from oxygen single vacancy (F and F+ color centers) and vacancy pair (F2+ and F22+ color centers). The oxygen single vacancy initially increases rapidly and then does not increase in the fluence range from 0.1 to 0.5 × 1014 ions/cm2. When the fluence is higher than 0.5 × 1014 ions/cm2, oxygen single vacancy starts to increase again. Oxygen vacancy pair increases monotonically with fluence for all irradiated samples. The variation of oxygen single vacancy with fluence is probably associated with the recombination of oxygen vacancies with Al interstitials and complex defect formation (such as vacancy clusters). From PL spectra, two emission bands around 3.1 and 2.34 eV are observed. The PL intensity of the emission band around 3.1 eV decreases for all the irradiated samples. For the emission band around 2.34 eV, the PL intensity initially decreases, and then increases with fluence. Meanwhile, the peak position of the emission band around 2.34 eV gradually shifts to high energy direction with increase of fluence. The decrease of the intensity of the emission bands around 3.1 and 2.34 eV could be induced by stress from the damage layer in the irradiated samples. The shift of peak position for the emission band around 2.34 eV is induced by the appearance of emission band from Al interstitials.

Bactericide effect of methylene blue associated with low-level laser therapy in Escherichia coli bacteria isolated from pressure ulcers.

PubMed

Gomes, Thais Ferreira; Pedrosa, Matheus Masalskiene; de Toledo, Ana Claudia Laforga; Arnoni, Veridiana Wanshi; Dos Santos Monteiro, Mirian; Piai, Davi Cury; Sylvestre, Silvia Helena Zacarias; Ferreira, Bruno

2018-05-09

The present study analyzed the bactericidal effect of methylene blue associated with low-level lasers on Escherichia coli isolated from a pressure ulcer. Microbiological material from a pressure ulcer was isolated using an aseptic swab, and antimicrobial activity was verified using the diffusion disc method. Methylene blue was used at concentrations of 0.001 and 0.005%, and low-level lasers of 670, 830, and 904 nm, with the energy densities of 4, 8, 10, and 14 J/cm 2 , were tested on three plates each and combined with methylene blue of each concentration. In addition, three control plates were used, with each concentration and energy density separated without any interventions. The results were analyzed using the paired sample t test to determine the bactericidal effect of the methylene blue and using the ANOVA test to compare the effects of the energy densities and wavelengths among the low-level laser treatment protocols. The results showed bacterial reduction at wavelengths of 830 and 904 nm and more proliferation in wavelengths of 670 nm. In wavelength of 830 nm, a bacterial reduction was observed in the conditions with 0.001% methylene blue in all energy density utilized, with 0.005% methylene blue in energy density of 10 J/cm 2 , and without methylene blue in energy density at 10 J/cm 2 . And in a wavelength of 904 nm, all condition showed bacterial reduction with or without methylene blue. We concluded that the low-level lasers of 904 and 830 nm have bactericidal effects and at better energy densities (10 and 14 J/cm 2 ).

Soil Carbon Changes in Transitional Grain Crop Production Systems in South Dakota

NASA Astrophysics Data System (ADS)

Woodard, H. J.

2004-12-01

Corn-C (Zea Mays L.), soybean-S (Glycine max L.) and spring wheat-W (Triticum aestivum L.) crops were seeded as a component of either a C-S, S-W, or C-S-W crop rotation on silt-loam textured soils ranging from 3.0-5.0% organic matter. Conservation tillage(chisel plow-field cultivator) was applied to half of the plots. The other plots were direct seeded as a no-till (zero-tillage) treatment. Grain yield and surface crop residues were weighed from each treatment plot. Crop residue (stover and straw) was removed from half of the plots. After four years, soil samples were removed at various increments of depth and soil organic carbon (C) and nitrogen (N) was measured. The ranking of crop residue weights occurred by the order corn>>soybean>wheat. Surface residue accumulation was also greatest with residue treatments that were returned to the plots, those rotations in which maize was a component, and those without tillage. Mean soil organic carbon levels in the 0-7.5cm depth decreased from 3.41% to 3.19% (- 0.22%) with conventional tillage (chisel plow/field cultivator) as compared to a decrease from 3.19% to 3.05% (-0.14%) in plots without tillage over a four year period. Organic carbon in the 0-7.5cm depth decreased from 3.21% to 3.01% (- 0.20%) after residue removed as compared to a decrease from 3.39% to 3.23% (-0.17%) in plots without tillage applied after four years. The soil C:N ratio (0-7.5cm) decreased from 10.63 to 10.37 (-0.26 (unitless)) in the tilled plots over a four-year period. Soil C:N ratio at the 0-7.5cm depth decreased from 10.72 to 10.04 (-0.68) in the no-till plots over a four year period. Differences in the soil C:N ratio comparing residue removed and residue returned were similar (-0.51 vs. -0.43 respectively). These soils are highly buffered for organic carbon changes. Many cropping cycles are required to determine how soil carbon storage is significantly impacted by production systems.

Estimation of CO2 diffusion coefficient at 0-10 cm depth in undisturbed and tilled soils

USDA-ARS?s Scientific Manuscript database

Diffusion coefficients (D) of CO2 at 0 – 10 cm layers in undisturbed and tilled soil conditions were estimated using Penman, Millington-Quirk, Ridgwell et al. (1999), Troeh et al., and Moldrup et al. models. Soil bulk density and volumetric soil water content ('v) at 0 – 10 cm were measured on April...

Identification of functionally active aerobic methanotrophs in sediments from an arctic lake using stable isotope probing

USGS Publications Warehouse

He, Ruo; Wooller, Matthew J.; Pohlman, John W.; Catranis, Catharine; Quensen, John; Tiedje, James M.; Leigh, Mary Beth

2012-01-01

Arctic lakes are a significant source of the greenhouse gas methane (CH4), but the role that methane oxidizing bacteria (methanotrophs) play in limiting the overall CH4 flux is poorly understood. Here, we used stable isotope probing (SIP) techniques to identify the metabolically active aerobic methanotrophs in upper sediments (0–1 cm) from an arctic lake in northern Alaska sampled during ice-free summer conditions. The highest CH4 oxidation potential was observed in the upper sediment (0–1 cm depth) with 1.59 μmol g wet weight-1 day-1 compared with the deeper sediment samples (1–3 cm, 3–5 cm and 5–10 cm), which exhibited CH4 oxidation potentials below 0.4 μmol g wet weight-1 day-1. Both type I and type II methanotrophs were directly detected in the upper sediment total communities using targeted primer sets based on 16S rRNA genes. Sequencing of 16S rRNA genes and functional genes (pmoA and mxaF) in the 13C-DNA from the upper sediment indicated that type I methanotrophs, mainly Methylobacter, Methylosoma, Methylomonas and Methylovulum miyakonense, dominated the assimilation of CH4. Methylotrophs, including the genera Methylophilus and/or Methylotenera, were also abundant in the 13CDNA. Our results show that a diverse microbial consortium acquired carbon from CH4 in the sediments of this arctic lake.

Bioenhanced dissolution of dense non-aqueous phase of trichloroethylene as affected by iron reducing conditions: model systems and environmental samples.

PubMed

Paul, Laiby; Smolders, Erik

2015-01-01

The anaerobic biotransformation of trichloroethylene (TCE) can be affected by competing electron acceptors such as Fe (III). This study assessed the role of Fe (III) reduction on the bioenhanced dissolution of TCE dense non-aqueous phase liquid (DNAPL). Columns were set up as 1-D diffusion cells consisting of a lower DNAPL layer, a layer with an aquifer substratum and an upper water layer that is regularly refreshed. The substrata used were either inert sand or sand coated with 2-line ferrihydrite (HFO) or two environmental Fe (III) containing samples. The columns were inoculated with KB-1 and were repeatedly fed with formate. In none of the diffusion cells, vinyl chloride or ethene was detected while dissolved and extractable Fe (II) increased strongly during 60 d of incubation. The cis-DCE concentration peaked at 4.0 cm from the DNAPL (inert sand) while it was at 3.4 cm (sand+HFO), 1.7 cm and 2.5 cm (environmental samples). The TCE concentration gradients near the DNAPL indicate that the DNAPL dissolution rate was larger than that in an abiotic cell by factors 1.3 (inert sand), 1.0 (sand+HFO) and 2.2 (both environmental samples). This results show that high bioavailable Fe (III) in HFO reduces the TCE degradation by competitive Fe (III) reduction, yielding lower bioenhanced dissolution. However, Fe (III) reduction in environmental samples was not reducing TCE degradation and the dissolution factor was even larger than that of inert sand. It is speculated that physical factors, e.g. micro-niches in the environmental samples protect microorganisms from toxic concentrations of TCE. Copyright © 2014 Elsevier Ltd. All rights reserved.

Solubility, Stability, Physicochemical Characteristics and In Vitro Ocular Tissue Permeability of Hesperidin: a Natural Bioflavonoid

PubMed Central

Majumdar, Soumyajit; Srirangam, Ramesh

2008-01-01

Purpose Hesperidin holds potential in treating age-related macular degeneration, cataract and diabetic retinopathy. The aim of this study, constituting the first step towards efficient ocular delivery of hesperidin, was to determine its physicochemical properties and in vitro ocular tissue permeability. Methods pH dependent aqueous solubility and stability were investigated following standard protocols. Permeability of hesperidin across excised rabbit cornea, sclera, and sclera plus retinal pigmented epithelium (RPE) was determined using a side-bi-side diffusion apparatus. Results Hesperidin demonstrated poor, pH independent, aqueous solubility. Solubility improved dramatically in the presence of 2-hydroxypropyl-beta-cyclodextrin (HP-β-CD) and the results supported 1:1 complex formation. Solutions were stable in the pH and temperature (25, 40°C) conditions tested, except for samples stored at pH 9. Transcorneal permeability in the apical-basal and basal-apical directions was 1.11±0.86×10−6 and 1.16±0.05×10−6 cm/s, respectively. The scleral tissue was more permeable (10.2±2.1×10−6cm/s). However, permeability across sclera/choroid/RPE in the sclera to retina and retina to sclera direction was 0.82±0.69×10−6, 1.52±0.78×10−6 cm/s, respectively, demonstrating the barrier properties of the RPE. Conclusion Our results suggest that stable ophthalmic solutions of hesperidin can be prepared and that hesperidin can efficiently permeate across the corneal tissue. Further investigation into its penetration into the back-of-the eye ocular tissues is warranted. PMID:18810327

Low-velocity collision behaviour of clusters composed of sub-millimetre sized dust aggregates

NASA Astrophysics Data System (ADS)

Brisset, J.; Heißelmann, D.; Kothe, S.; Weidling, R.; Blum, J.

2017-07-01

Context. The experiment results presented apply to the very first stages of planet formation, when small dust aggregates collide in the protoplanetary disc and grow into bigger clusters. In 2011, before flying on the REXUS 12 suborbital rocket in 2012, the Suborbital Particle and Aggregation Experiment (SPACE) performed drop tower flights. We present the results of this first microgravity campaign. Aims: The experiments presented aim to measure the outcome of collisions between sub-mm sized protoplanetary dust aggregate analogues. We also observed the clusters formed from these aggregates and their collision behaviour. Methods: The experiments were performed at the drop tower in Bremen. The protoplanetary dust analogue materials were micrometre-sized monodisperse and polydisperse SiO2 particles prepared into aggregates with sizes between 120 μm and 250 μm. One of the dust samples contained aggregates that were previously compacted through repeated bouncing. During three flights of 9 s of microgravity each, individual collisions between aggregates and the formation of clusters of up to a few millimetres in size were observed. In addition, the collisions of clusters with the experiment cell walls leading to compaction or fragmentation were recorded. Results: We observed collisions amongst dust aggregates and collisions between dust clusters and the cell aluminium walls at speeds ranging from about 0.1 cm s-1 to 20 cm s-1. The velocities at which sticking occurred ranged from 0.18 to 5.0 cm s-1 for aggregates composed of monodisperse dust, with an average value of 2.1 ± 0.9 cm s-1 for reduced masses ranging from 1.2 × 10-6 to 1.8 × 10-3 g with an average value of 2.2+16-2.1 × 10-4 g. The velocities at which bouncing occurred ranged from 1.9 to 11.9 cm s-1 for the same aggregates with an average of 5.9 ± 3.2 cm s-1 for reduced masses ranging from 2.1 × 10-6 to 2.4 × 10-4 with an average of 7.8 ± 2.4 × 10-5 g. The velocities at which fragmentation occurred ranged from 4.9 to 23.8 cm s-1 for the same aggregates with an average of 10.1 ± 3.2 cm s-1 for reduced masses ranging from 1.2 × 10-5 to 1.2 × 10-3 with an average value of 4.2 ± 2.4 × 10-4 g. From the restructuring and fragmentation of clusters composed of dust aggregates colliding with the aluminium cell walls, we derived a collision recipe for dust aggregates ( 100 μm) following the model of Dominik & Tielens (1997, ApJ, 480, 647) developed for microscopic particles. We measured a critical rolling energy of 1.8 ± 0.9 × 10-13 J and a critical breaking energy of 3.5 ± 1.5 × 10-13 J for 100 μm-sized non-compacted aggregates. A movie associated to Fig. 3 is available at http://www.aanda.org

Spatial 2D distribution of the proportion of soil phosphorus uptake by maize and soybean caused by tillage and fertilization

NASA Astrophysics Data System (ADS)

Li, Haixiao; Mollier, Alain; Ziadi, Noura; Messiga, Aimé Jean; Parent, Leon-Étienne; Morel, Christian

2017-04-01

Plant-available soil phosphorus (P) accumulates primarily in the topsoil due to P fertilization and P released from crop residues. In contrast with conventional tillage (moldboard plough, MP), conservation tillage [e.g. no-till, (NT)] often leads to higher P concentrations in the topsoil mainly due to the absence of mixing between soil, fertilizer, and crop residues. Our objective was to estimate the proportion of P uptake from a given soil mass across the soil profile under maize and soybean as the product of root surface density proportions and local plant-available soil P. This study was conducted on a long-term field experiment initiated in 1992 in southern Quebec, Canada, and established on a clay-loam soil under MP and NT systems. The experiment was factorially treated with three P doses (0, 17.5 and 35 kg P ha-1 applied as triple superphosphate on maize at 5 cm depth and at 5 cm on one side of the crop row). Soil was sampled at flowering stage at five depths (0-5, 5-10, 10-20, 20-30 and 30-40 cm) and three horizontal distances perpendicular to the crop row (5, 15 and 25 cm) in 2014 and 2015 to map a grid soil P availability to plants, e.g. phosphate ion concentrations in solution and the time-dependent amount of phosphate ions that can equilibrate- solution by diffusion, root distribution, and consequently crop P uptake, which was calculated as the fraction of plant-available soil P intercepted by surface roots. In general, NT tended to have higher soil P status in the upper soil layer and lower soil P status in the deeper soil layer compared to MP ; confirming previous results obtained from the same experimental site. This variation along the soil profile was significantly affected by sampling distance to crop row with higher concentration observed at 5-cm distance mainly because of the placement of P fertilizers. The 2D distribution of P uptake depended on tillage practice and P fertilization. There was higher proportions of P uptake from the 0-10 and 0-20 cm layers in NT (46% and 79%, respectively) compared to MP (25% and 68%, respectively). On average 8% of P uptake originated from the 30-40 cm layer irrespective of tillage, indicating that plant P uptake from deeper soil layers also influenced the P cycling in agroecosystems.

Renovation of epithermal neutron beam for BNCT at THOR.

PubMed

Liu, Y-W H; Huang, T T; Jiang, S H; Liu, H M

2004-11-01

Heading for possible use for clinical trial, THOR (Tsing Hua Open-pool Reactor) at Taiwan was shutdown for renovation of a new epithermal neutron beam in January 2003. In November 2003, concrete cutting was finished for closer distance from core and larger treatment room. This article presents the design base that the construction of the new beam is based on. The filter/moderator design along the beam is Cd(0.1cm)+Al(10 cm)+FLUENTAL (16 cm)+Al(10 cm)+FLUENTAL(24 cm)+Void(18 cm)+Cd(0.1cm)+Bi(10 cm) with 6 cm Pb as reflector. Following the filter/moderator is an 88 cm long, 6 cm thick Bi-lined collimator with Li(2)CO(3)-PE at the end. The collimator is surrounded by Li(2)CO(3)-PE and Pb. The calculated beam parameters under 2 MW at the beam exit is phi(epi) = 3.4 x 10(9) n/cm(2)/s, Df/phi(epi) = 2.8 x 10(-11) cGy cm(2)/n, Dgamma/phi(epi) = 1.3 x 10(-11) cGy cm(2)/n, and J+/phi = 0.8. For a phantom placed 10 cm from beam exit, MCNP calculation shows that the advantage depth is 8.9 cm, and advantage ratio is 5.6 if boron concentration in tumor and normal tissue are assumed to be 65 and 18 ppm. The maximum dose rate for normal tissue is 50 cGy/min. The maximum therapeutic ratio is 6. The construction of the beam is scheduled to be finished by the end of April 2004.

The role of groundwater in streamflow in a headwater catchment with sub-humid climate

NASA Astrophysics Data System (ADS)

Liu, Yaping; Tian, Fuqiang; Hu, Hongchang; Tie, Qiang

2015-04-01

Recent studies have suggested that bedrock groundwater can exert considerable influence on streamflow in headwater catchments under humid climate. However, study of the role of bedrock groundwater is still challenged due to limited direct observation data. In this study, by utilizing observed hydrometric and hydrochemical data, we aimed at characterize the bedrock groundwater's response to rainfall at hillslope and catchment scales in a small headwater catchment with sub-humid climate. We selected Xitaizi catchment with area of 6.7 km in the earth-rock mountain region, which located in the north of Beijing, China, as study area. The catchment bedrock is mainly consist of fractured granite. Four weather stations were installed to observe the weather condition and soil volumetric water content (VWC) at depth of 10-60 cm with 10-minute interval. Five wells with depth of 10 m were drilled in two slopes to monitor the bedrock water table by pneumatic water gauge. At slope 1, the soil VWC at depth of 10-80 cm were also observed by soil moisture sensors, and surface/subsurface hillslope runoff at three different layers (0-20cm, 20-80cm, 80-300cm) was observed by three recording buckets. Field works were conducted from July 2013 to November 2014. During the period, precipitation, river, spring and groundwater were sampled nearly monthly. Water temperature, electrical conductivity (EC) and pH were measured in site with portable instruments. In addition, the precipitation, river and groundwater were also sampled intensively during two storm events. All the samples were subjected to stable isotope analysis, the samples taken monthly during the period from July 2013 to July 2014 were subjected to hydrochemistry analysis. Our results show that: (1) the bedrock groundwater is the dominant component of streamflow in the headwater catchment with sub-humid climate; (2) stream is recharged by groundwater sourcing from different mountains with different hydrochemistry characteristics; (3) the contribution of bedrock groundwater to the peak part of hydrograph was not observed from both hydrometric and isotopic data.

Search For Gamma-Ray Emission From X-Ray-Selected Seyfert Galaxies With Fermi -LAT

DOE PAGES

Ackermann, M.

2012-02-23

We report on a systematic investigation of the γ-ray properties of 120 hard Xray– selected Seyfert galaxies classified as ‘radio-quiet’ objects, utilizing the threeyear accumulation of Fermi–LAT data. Our sample of Seyfert galaxies is selected using the Swift–BAT 58-month catalog, restricting the analysis to the bright sources with average hard X-ray fluxes F14-195 keV ≥ 2.5 × 10 -11 erg cm -2 s -1 at high Galactic latitudes (|b| > 10°). In order to remove ‘radio-loud’ objects from the sample, we use the ‘hard X-ray radio loudness parameter’, RrX , defined as the ratio of the total 1.4 GHz radiomore » to 14 - 195 keV hard X-ray energy fluxes. Among 120 X-ray bright Seyfert galaxies with RrX < 10-4, we did not find a statistically significant γ-ray excess (TS > 25) positionally coincident with any target Seyferts, with possible exceptions of ESO 323–G077 and NGC 6814. The mean value of the 95% confidence level γ-ray upper limit for the integrated photon flux above 100 MeV from the analyzed Seyferts is ≃ 4×10 -9 ph cm -2 s -1 , and the upper limits derived for several objects reach ≃ 1 × 10 -9 ph cm -2 s -1 . Our results indicate that no prominent γ-ray emission component related to active galactic nucleus activity is present in the spectra of Seyferts around GeV energies. The Fermi–LAT upper limits derived for our sample probe the ratio of γ-ray to X-ray luminosities L /LX < 0.1, and even < 0.01 in some cases. The obtained results impose novel constraints on the models for high energy radiation of ‘radio-quiet’ Seyfert galaxies.« less

Iridium and trace element measurements from the Cretaceous-Tertiary boundary, site 752, Broken Ridge, Indian Ocean

NASA Technical Reports Server (NTRS)

Schuraytz, B. C.; O'Connell, S.; Sharpton, V. L.

1991-01-01

Fourteen samples spanning a 2.5 m interval that includes the Cretaceous-Tertiary (K/T) boundary from Hole 752B near the crest of Broken Ridge in the eastern Indian Ocean were studied in order to search for anomalous enrichments of iridium (Ir) and shock-metamorphosed quartz grains. No allogenic quartz grains larger than 10 microns were observed, hence the presence of quartz containing diagnostic evidence of shock-metamorphism could not be confirmed. Two Ir anomalies of 2.2 +/- 0.6 and 2.0 +/- 0.4 parts per billion (ppb) were measured in samples of dark green ash-bearing chalk at depths of 357.93 and 358.80 m below seafloor, respectively. These samples containing anomalous enrichments of Ir were taken from approximately 82 cm above and 5 cm below the extinction level of Globotruncanids. Our results are consistent with those of Michel et al., who observe elevated concentrations of Ir at these depths in addition to a larger Ir anomaly associated with the extinction level of Globotruncanids.

Nano carbon black-based screen printed sensor for carbofuran, isoprocarb, carbaryl and fenobucarb detection: application to grain samples.

PubMed

Della Pelle, Flavio; Angelini, Claudia; Sergi, Manuel; Del Carlo, Michele; Pepe, Alessia; Compagnone, Dario

2018-08-15

An electrochemical screening assay for the detection of phenyl carbamates (i.e. carbaryl, carbofuran, isoprocarb and fenobucarb) was developed and applied to grains samples (i.e. durum wheat, soft wheat and maize). Nano carbon black (CB) was strategically employed to realize an effective, reproducible, fouling resistant, low cost, delocalisable screen printed sensor (CB-SPE). CB-SPEs morphology (SEM and FEM) and electrochemical property (CV and EIS) were studied. The final pesticides analysis protocol consist of: (i) extraction of the analyte (just by mixing), (ii) alkaline hydrolysis (10 min R.T.), (iii) DPV detection directly of 100 µL of extract on the CB-SPE surface. Linear range between 1.0 × 10 -7 and 1.0 × 10 -4 mol L -1 , good determination coefficients (R 2 ≥ 0.9971) and satisfactory sensitivity (≥ 3.90 × 10 -1 A M -1 cm -2 ) and LODs (≤ 8.0 × 10 -8 mol L -1 ) were obtained for all the analytes. Excellent recoveries (78-102%) and accuracy (relative error vs. HPLC-MS/MS between 9.0% and -7.8%) resulted from the analysis of grains samples. The proposed CB-SPE based approach has demonstrated to be able to detect carbaryl at Maximum residue limits levels (MRLs), allowing class selective detection of commonly employed phenyl carbamates in food samples. Copyright © 2018 Elsevier B.V. All rights reserved.

Photoinactivation effect of eosin methylene blue and chlorophyllin sodium-copper against Staphylococcus aureus and Escherichia coli.

PubMed

Caires, Cynthia S A; Leal, Cassia R B; Ramos, Carlos A N; Bogo, Danielle; Lima, Alessandra R; Arruda, Eduardo J; Oliveira, Samuel L; Caires, Anderson R L; Nascimento, Valter A

2017-07-01

The use of eosin methylene blue according to Giemsa as photosensitizer is presented for the first time in this paper. The present study evaluated the potential application of chlorophyllin sodium copper salt (CuChlNa) and eosin methylene blue according to Giemsa (EMB) as antimicrobial photosensitizers (aPS) for photodynamic inactivation (PDI) of Staphylococcus aureus (gram-positive) and Escherichia coli (gram-negative) bacteria. The experiments were performed using S. aureus stain ATCC 25923 and E. coli ATCC 25922 in which five aPS concentrations (0.0, 1.0, 2.5, 5.0, 10.0, and 20.0 μM for S. aureus and 0.0, 5.0, 10.0, 20.0, 40.0, and 50.0 μM for E. coli) were prepared and added in 2 mL of a saline solution containing the bacterial inoculum. After aPS incubation, the samples were divided into two groups, one kept in the dark and another submitted to the illumination. Then, the bacterial inactivation was determined 18 h after the incubation at 37 °C by counting the colony-forming units (CFU). The results revealed that both EMB and CuChlNa can be used as aPS for the photoinactivation of S. aureus, while only EMB was able to photoinactivate E. coli. Nevertheless, a more complex experimental setup was needed for photoinactivation of E. coli. The data showed that EMB and CuChlNa presented similar photoinactivation effects on S. aureus, in which bacterial growth was completely inhibited at photosensitizer (PS) concentrations over 5 μM, when samples were previously incubated for 30 min and irradiated by a light dose of 30 J cm -2 as a result of an illumination of 1 h at 8.3 mW cm -2 by using a red light at 625 nm with a 1 cm beam diameter and output power of 6.5 mW. In the case of E. coli, bacterial growth was completely inhibited only when combining a PS incubation period of 120 min with concentrations over 20 μM.

Comparison of methods for the enumeration of enterohemorrhagic Escherichia coli from veal hides and carcasses.

PubMed

Luedtke, Brandon E; Bosilevac, Joseph M

2015-01-01

The increased association of enterohemorrhagic Escherichia coli (EHEC) with veal calves has led the United States Department of Agriculture Food Safety and Inspection Service to report results of veal meat contaminated with the Top 7 serogroups separately from beef cattle. However, detection methods that can also provide concentration for determining the prevalence and abundance of EHEC associated with veal are lacking. Here we compared the ability of qPCR and a molecular based most probable number assay (MPN) to detect and enumerate EHEC from veal hides at the abattoir and the resulting pre-intervention carcasses. In addition, digital PCR (dPCR) was used to analyze select samples. The qPCR assay was able to enumerate total EHEC in 32% of the hide samples with a range of approximately 34 to 91,412 CFUs/100 cm(2) (95% CI 4-113,460 CFUs/100 cm(2)). Using the MPN assay, total EHEC was enumerable in 48% of the hide samples and ranged from approximately 1 to greater than 17,022 CFUs/100 cm(2) (95% CI 0.4-72,000 CFUs/100 cm(2)). The carcass samples had lower amounts of EHEC with a range of approximately 4-275 CFUs/100 cm(2) (95% CI 3-953 CFUs/100 cm(2)) from 17% of samples with an enumerable amount of EHEC by qPCR. For the MPN assay, the carcass samples ranged from 0.1 to 1 CFUs/100 cm(2) (95% CI 0.02-4 CFUs/100 cm(2)) from 29% of the samples. The correlation coefficient between the qPCR and MPN enumeration methods indicated a moderate relation (R (2) = 0.39) for the hide samples while the carcass samples had no relation (R (2) = 0.002), which was likely due to most samples having an amount of total EHEC below the reliable limit of quantification for qPCR. Interestingly, after enrichment, 81% of the hide samples and 94% of the carcass samples had a detectable amount of total EHEC by qPCR. From our analysis, the MPN assay provided a higher percentage of enumerable hide and carcass samples, however determining an appropriate dilution range and the limited throughput offer additional challenges.

Measurements of size-fractionated concentration and bulk dry deposition of atmospheric particulate bound mercury

NASA Astrophysics Data System (ADS)

Fang, G. C.; Zhang, L.; Huang, C. S.

2012-12-01

Daily samples of size-fractionated (18, 10, 2.5 and 1.0 μm) particulate-bound mercury Hg(p) were collected using Micro-Orifice Uniform Deposition Impactors (MOUDI), on randomly selected days each month between November 2010 and July 2011, at a traffic site (Hungkuang), a wetland site (Gaomei), and an industrial site (Quanxing) in central Taiwan. Bulk dry deposition was also collected simultaneously using a surrogate surface. The nine-month average (±standard deviation) Hg(p) concentrations were 0.57 (±0.90), 0.17 (±0.27), and 0.94 (±0.92) ng m-3 at Hungkuang, Gaomei, and Quanxing, respectively. Concentrations in November and December were much higher than in the other months due to a combination of high local emissions and meteorological conditions. PM1.0 contributed more than 50% to the bulk concentration at the traffic and the industrial sites, but only contributed 25% at the wetland site. PM1.0-2.5 contributed 25%-50%, depending on location, to the bulk mass. Coarse fraction (PM2.5-18) contributed 7% at Hungkuang, 25% at Gaomei, and 19% at Quanxing. Samples with very high bulk concentrations had large fine fractions. Annual dry deposition estimated from the surrogate surface measurements was in the range of 30-85 μg m-2 yr-1 at the three sites. Coarse particulate Hg(p) were estimated to contribute 50-85% of the total Hg(p) dry deposition. Daily dry deposition velocities (Vd) ranged from 0.01 to 7.7 cm s-1. The annual Vd generated from the total measured fluxes was 0.34, 0.60 and 0.29 cm s-1 at Hungkuang, Gaomei, and Quanxing, respectively. These values can be reasonably reproduced using a size-resolved model and measured size fractions.

Control of high-Z PFC erosion by local gas injection in DIII-D

NASA Astrophysics Data System (ADS)

Rudakov, D. L.; Stangeby, P. C.; Wong, C. P. C.; McLean, A. G.; Wampler, W. R.; Watkins, J. G.; Boedo, J. A.; Briesemeister, A.; Buchenauer, D. A.; Chrobak, C. P.; Elder, J. D.; Fenstermacher, M. E.; Guo, H. Y.; Lasnier, C. J.; Leonard, A. W.; Maingi, R.; Moyer, R. A.

2015-08-01

Reduced erosion of a high-Z PFC divertor surface was observed in DIII-D with local injection of methane and deuterium gases. Molybdenum-coated silicon samples were exposed in the lower divertor of DIII-D using DiMES under plasma conditions previously shown to cause significant net erosion of Mo. Three exposures with 13CH4 and one exposure with D2 gas injection about 12 cm upstream of the samples located within 1-2 cm of the attached strike point were performed. Reduction of Mo erosion was evidenced in-situ by the suppression of MoI line radiation at 386.4 nm once the gas injection started. Post-mortem ion beam analysis demonstrated that the net erosion of molybdenum near the center of the samples exposed with 13CH4 injection was below the measurement resolution of 0.5 nm, corresponding to a rate of ⩽0.04 nm/s. Compared to the previously measured erosion rates, this constitutes a reduction by a factor of >10.

Effect of the annealing ambient on the electrical characteristics of the amorphous InGaZnO thin film transistors.

PubMed

Huang, Yu-Chih; Yang, Po-Yu; Huang, Hau-Yuan; Wang, Shui-Jinn; Cheng, Huang-Chung

2012-07-01

The influence of the thermal annealing on the amorphous indium gallium zinc oxide (a-IGZO) thin-film transistors (TFTs) under different ambient gases has been systematically addressed. The chemical bonding states and transfer characteristics of a-IGZO TFTs show evident dependence on the annealing ambient gas. For the a-IGZO TFTs in the oxygen ambient annealing at 250 degrees C for 30 mins exhibited a maximum field effect mobility (max muFE) of 9.36 cm2/V x s, on/off current ratio of 6.12 x 10(10), and a subthreshold slope (SS) of 0.21 V/decade. Respectively, the as-deposited ones without annealing possess a max muFE of 6.61 cm2/V x s, on/off current ratio of 4.58 x 10(8), and a SS of 0.46 V/decade. In contrast, the a-IGZO TFTs annealed at 250 degrees C for 30 mins in the nitrogen ambient would be degraded to have a max muFE of 0.18 cm2/V x s, on/off current ratio of 2.22 x 10(4), and a SS of 7.37 V/decade, corresponding. It is attributed to the content of the oxygen vacancies, according the x-ray photoelectron spectroscopy (XPS) analyze of the three different samples.

New synthesis of nanopowders of proton conducting materials. A route to densified proton ceramics

NASA Astrophysics Data System (ADS)

Khani, Zohreh; Taillades-Jacquin, Mélanie; Taillades, Gilles; Marrony, Mathieu; Jones, Deborah J.; Rozière, Jacques

2009-04-01

Low temperature routes have been developed for the preparation of BaCe 0.9Y 0.1O 2.95 (BCY10) and BaZr 0.9Y 0.1O 2.95 (BZY10) in the form of nanoparticulate powders for use after densification as ceramic membranes for a proton ceramic fuel cell. These methods make use on the one hand of the chelation of metal (II), (III) and (IV) ions by acrylates (hydrogelation route) and on the other of the destabilisation and precipitation of micro-emulsions. Both routes lead to single phase yttrium doped barium cerate or zirconate perovskites, as observed by X-ray diffraction, after thermal treatment at 900 °C for 4 h for BCY10 and 800 °C for BZY10. These temperatures, lower than those usually used for preparation of barium cerate or zirconate, lead to oxide nanoparticles of size <40 nm. Dense ceramics (⩾95%) are obtained by sintering BCY10 pellets at 1350 °C and BZY10 pellets at 1500 °C for 10 h. The water uptake of compacted samples at 500 °C is 0.14 wt% for BCY10 and 0.26 wt% for BZY10. Total conductivities in the range 300-600 °C were determined using impedance spectroscopy in a humidified nitrogen atmosphere. The total conductivity was 1.8×10 -2 S/cm for BCY10 and 2×10 -3 S/cm for BZY10 at 600 °C. The smallest perovskite nanoparticles and highest conductivities were obtained by hydrogelation of precursor barium, zirconium, cerium and yttrium acrylates.

[Evolution pattern of phytolith-occluded carbon in typical forest-soil ecosystems in tropics and subtropics, China.

PubMed

He, Shan Qiong; Huang, Zhang Ting; Wu, Jia Sen; Yang, Jie; Jiang, Pei Kun

2016-03-01

Samples of fresh leaves and leaf litter, as well as soils taken from 0-10 and 10-30 cm layers, were collected in four types of typical forest ecosystems both in subtropical (Phyllostachys pubescens, Pinus massoniana, Cycloba lanopsisglauca, and Cunninghamia lanceolata stands) and in tropical climates (Vatica mangachapoi, Musa basjoo, Heveabrasiliensis, and Acacia mangium stands) for measurement of PhytOC (phytolith-occluded organic carbon) contents. The phytoliths in both leaves and soil samples were extracted by a microwave digestion method and their PhytOC contents were determined by alkali dissolution-spectrophotometry method. It was found that, among the four types of subtropical forests, the PhytOC contents of leaves, litter and 0-10 cm soil layer were the highest in P. massoniana stand (230.24, 229.17 and 20.87 g·kg -1 ), the lowest in P. pubescens stand (30.55, 37.37, and 3.38 g·kg -1 ), and the PhytOC content of the 10-30 cm soil layer was the highest in C. glauca stand (18.54 g·kg -1 ), and the lowest in P. pubescens stand (2.90 g·kg -1 ). For the four tropical forests, A. mangium stand (377.66 g·kg -1 ) and V. mangachapoi stand (46.83 g·kg -1 ), respectively, deposited the highest and lowest contents of PhytOC in the leaves, while the highest and lowest contents of PhytOC in the litter were observed in H. brasiliensis stand (218.23 g·kg -1 ) and M. basjoo stand (27.66 g·kg -1 ), respectively. Also among the tropical forests, the highest PhytOC contents in the 0-10 cm and 10-30 cm soil layers were observed in A. mangium stand (23.84 and 24.90 g·kg -1 ), while the lowest values occurred in M. basjoo stand (3.89 and 3.93 g·kg -1 ). The PhytOC contents in transitioning from leaves to soils (0-10 cm layers) decreased by 97.4% for C. lanceolata, 94.9% for C. glauca, 90.9% for P. massoniana, and 88.9% for P. pubescens in the subtropics, and by 95.9% for H. brasiliensis, 93.7% for A. mangium, 93.3% for M. basjoo, 63.7% for V. mangachapoi in the tropics. There was no significant difference in PhytOC contents between leaves and litter for the following five forest types: P. pubescens, P. massoniana, C. lanceolata, V. mangachapoi and H. brasiliensis. However, significantly higher PhytOC contents in leaves than in litters were measured in C. glauca, M. basjoo, and A. mangium. The findings that significantly lower PhytOC contents occurred in soils than in fresh leaves and leaf litter regardless of type of forest ecosystem suggested that phytolith was not stable during the pathway from plants to soil via the forest litter.

Transformation of soil organic matter in leached chernozems under minimized treatment in the forest-steppe of West Siberia

NASA Astrophysics Data System (ADS)

Sharkov, I. N.; Samokhvalova, L. M.; Mishina, P. V.

2016-07-01

Changes in the contents of total organic carbon and the carbon of easily mineralizable fractions of organic matter (labile humus, detritus, and mortmass) in the layers of 0-10, 10-25, and 0-25 cm were studied in leached chernozems ((Luvic Chernozems (Loamic, Aric)) subjected to deep plowing and surface tillage for nine years. In the layer of 0-25 cm, the content of Corg did not show significant difference between these two treatments and comprised 3.68-3.92% in the case of deep plowing and 3.63-4.08% in the case of surface tillage. Tillage practices greatly affected the distribution of easily mineralizable fractions of organic matter in the layers of 0-10 and 10-25 cm, though the difference between two treatments for the entire layer (0-25 cm) was insignificant. Surface tillage resulted in the increase in the contents of mortmass (by 59%), detritus (by 32%), and labile humus (by 8%) in the layer of 0-10 cm in comparison with deep plowing. At the same time, the contents of these fractions in the layer of 10-25 cm in the surface tillage treatment decreased by 67, 46, and 3%, respectively. The estimate of the nitrogen-mineralizing capacity made according to the data on the uptake of soil nitrogen by oat plants in a special greenhouse experiment confirmed the observed regularities of the redistribution of easily mineralizable organic matter fractions by the soil layers. In case of surface tillage, it increased by 23% in the layer of 0-10 cm; for the layer of 0-25 cm, no significant differences in the uptake of nitrogen by oat plants were found for the two studied treatments.

On-road ultrafine particle concentration in the M5 East road tunnel, Sydney, Australia

NASA Astrophysics Data System (ADS)

Knibbs, Luke D.; de Dear, Richard J.; Morawska, Lidia; Mengersen, Kerrie L.

The human health effects following exposure to ultrafine (<100 nm) particles (UFPs) produced by fuel combustion, while not completely understood, are generally regarded as detrimental. Road tunnels have emerged as locations where maximum exposure to these particles may occur for the vehicle occupants using them. This study aimed to quantify and investigate the determinants of UFP concentrations in the 4 km twin-bore (eastbound and westbound) M5 East tunnel in Sydney, Australia. Sampling was undertaken using a condensation particle counter (CPC) mounted in a vehicle traversing both tunnel bores at various times of day from May through July, 2006. Supplementary measurements were conducted in February, 2008. Over three hundred transects of the tunnel were performed, and these were distributed evenly between the bores. Additional comparative measurements were conducted on a mixed route comprising major roads and shorter tunnels, all within Sydney. Individual trip average UFP concentrations in the M5 East tunnel bores ranged from 5.53 × 10 4 p cm -3 to 5.95 × 10 6 p cm -3. Data were sorted by hour of capture, and hourly median trip average (HMA) UFP concentrations ranged from 7.81 × 10 4 p cm -3 to 1.73 × 10 6 p cm -3. Hourly median UFP concentrations measured on the mixed route were between 3.71 × 10 4 p cm -3 and 1.55 × 10 5 p cm -3. Hourly heavy diesel vehicle (HDV) traffic volume was a very good determinant of UFP concentration in the eastbound tunnel bore ( R2 = 0.87), but much less so in the westbound bore ( R2 = 0.26). In both bores, the volume of passenger vehicles (i.e. unleaded gasoline-powered vehicles) was a significantly poorer determinant of particle concentration. When compared with similar studies reported previously, the measurements described here were among the highest recorded concentrations, which further highlights the contribution road tunnels may make to the overall UFP exposure of vehicle occupants.

Vertical migration of some herbicides through undisturbed and homogenized soil columns

PubMed Central

Aktar, Md. Wasim; Sengupta, Dwaipayan; Purkait, Swarnali; Chowdhury, Ashim

2008-01-01

A laboratory experiment was conducted by using three herbicides, two from dinitroaniline group and one from thiocarbamate group to know their degree of downward movement (leachability) through soil columns and their contribution in ground water contamination. Soil columns were loaded with Pendimethalin, Benthiocarb and Oryzalin at doses of 10.0, 10.0 and 7.7 kg/ha, respectively. After 30 days soil samples were analyzed from each segments (i.e. 0–6, 6–12, 12–18, 18–24 and 24–30 cm) for Benthiocarb and Pendimethalin by GLC equipped with Ni63 electron capture detector (ECD) and for Oryzalin by HPLC coupled with UV-VIS detector. The results obtained in the present study reveal that the residues of the three herbicides under investigation were predominantly confined to the upper soil layer (0–6 cm). Comparatively, low mobility of these herbicides in soils could be due to strong adsorption of these chemical to soil colloids. PMID:21218121

Effects of Different Cutting Height on Nutritional Quality of Whole Crop Barley Silage and Feed Value on Hanwoo Heifers.

PubMed

Kim, Dong Hyeon; Amanullah, Sardar M; Lee, Hyuk Jun; Joo, Young Ho; Han, Ouk Kyu; Adesogan, Adegbola T; Kim, Sam Churl

2016-09-01

The present study evaluated the effects of different cutting height on nutritive value, fermentation quality, in vitro and in vivo digestibility of whole crop barley silage. Whole crop barley forage (Yuyeon hybrid) was harvested at height of 5, 10, and 15 cm from the ground level. Each cutting height was rolled to make round bale and ensiled for 100 days. After 100 days of ensiling, pH of silage was lower (p<0.05) in 5 cm, but no difference between 10 and 15 cm of cutting height. The content of lactate and lactate to acetate ratio were increased (p<0.05) in 5 cm of cutting height, whereas the acetate content was higher (p<0.05) in 10 and 15 cm than that of 5 cm cutting height. Aerobic stability was greater (p<0.05) in silages of 10 and 15 cm of cutting height. Three total mixed rations (TMR) were formulated with silages from the three different cutting heights (TMR5, TMR10, and TMR15) incorporated as forage at 70:30 ratio with concentrate (dry matter [DM] basis). In vitro dry matter digestibility was higher (p<0.05) in the TMR5 and TMR10 than that in TMR15, whereas in vitro neutral detergent fiber digestibility was higher (p<0.05) in the TMR10 and TMR15 than that in TMR5. Concentration of NH3-N was highest (p<0.05) in the TMR10 followed by TMR15 and TMR5. Total volatile fatty acid was decreased (p<0.05) with increased cutting height. The digestibility of DM and neutral detergent fiber were highest (p<0.05) in TMR15, than those in TMR5 and TMR10, whereas acid detergent fiber digestibility was higher (p<0.05) in TMR5 than that in TMR10. The results showed that increasing cutting height, at least up to 10 to 15 cm, of whole crop barley forage at harvest (Yuyeon) may be beneficial for making silage for TMR formulation and increasing digestibility of DM and NDF.

Effects of Different Cutting Height on Nutritional Quality of Whole Crop Barley Silage and Feed Value on Hanwoo Heifers

PubMed Central

Kim, Dong Hyeon; Amanullah, Sardar M.; Lee, Hyuk Jun; Joo, Young Ho; Han, Ouk Kyu; Adesogan, Adegbola T.; Kim, Sam Churl

2016-01-01

The present study evaluated the effects of different cutting height on nutritive value, fermentation quality, in vitro and in vivo digestibility of whole crop barley silage. Whole crop barley forage (Yuyeon hybrid) was harvested at height of 5, 10, and 15 cm from the ground level. Each cutting height was rolled to make round bale and ensiled for 100 days. After 100 days of ensiling, pH of silage was lower (p<0.05) in 5 cm, but no difference between 10 and 15 cm of cutting height. The content of lactate and lactate to acetate ratio were increased (p<0.05) in 5 cm of cutting height, whereas the acetate content was higher (p<0.05) in 10 and 15 cm than that of 5 cm cutting height. Aerobic stability was greater (p<0.05) in silages of 10 and 15 cm of cutting height. Three total mixed rations (TMR) were formulated with silages from the three different cutting heights (TMR5, TMR10, and TMR15) incorporated as forage at 70:30 ratio with concentrate (dry matter [DM] basis). In vitro dry matter digestibility was higher (p<0.05) in the TMR5 and TMR10 than that in TMR15, whereas in vitro neutral detergent fiber digestibility was higher (p<0.05) in the TMR10 and TMR15 than that in TMR5. Concentration of NH3-N was highest (p<0.05) in the TMR10 followed by TMR15 and TMR5. Total volatile fatty acid was decreased (p<0.05) with increased cutting height. The digestibility of DM and neutral detergent fiber were highest (p<0.05) in TMR15, than those in TMR5 and TMR10, whereas acid detergent fiber digestibility was higher (p<0.05) in TMR5 than that in TMR10. The results showed that increasing cutting height, at least up to 10 to 15 cm, of whole crop barley forage at harvest (Yuyeon) may be beneficial for making silage for TMR formulation and increasing digestibility of DM and NDF. PMID:27165022

Influence of Controlled Drainage and Liquid Dairy Manure Application on Phosphorus Leaching from Intact Soil Cores.

PubMed

Young, Eric O; Geibel, Justin R; Ross, Donald S

2017-01-01

Controlled drainage can reduce nitrate export from tile drainage flow, but its impact on phosphorus (P) loss is largely unknown. We compared P leaching from soil cores treated as free drainage (FD) or controlled drainage (CD) before and after manure application. In August 2012, 16 intact cores (45 cm long, 15 cm diameter) were collected from a grass forage field () located in Chazy, NY, and modified for drainage control and sampling. In Experiment 1 (no manure), initial leachate was defined as FD, and leachate collected 21 d later (valves closed) was considered CD. In Experiment 2, seven cores were randomly assigned to CD or FD. Liquid dairy manure was applied at 1.2 × 10 L ha, followed by simulated rainfall 2 h later. Leachate was sampled on Day 7, 14, and 21. Deionized water was applied at 3.4 cm h over 1 h to mimic a 10-yr rainfall event. Total P (TP), soluble reactive P (SRP), dissolved oxygen, iron (Fe), and pH were measured. Results showed that TP ( = 0.03) and SRP ( = 0.35) were lower for CD prior to manure application. Manure application caused 36- and 42-fold increases in TP and SRP; however, TP was lower for CD at 7 ( = 0.06), 14 ( = 0.003), and 21 d ( = 0.002) of water retention. Mean SRP for CD was nearly 40-fold lower than FD by Day 7 ( = 0.02) and remained low, suggesting CD in the field may reduce P export risk to tile drain flow after manure applications. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

Vertical distribution of 137Cs in grassland soils disturbed by moles (Talpa europaea L.).

PubMed

Ramzaev, V; Barkovsky, A

2018-04-01

Activity of biota is one of the factors influencing vertical migration of radionuclides deposited from the atmosphere onto the ground surface. The goal of this work was to study the vertical distribution of 137 Cs in grassland soils disturbed by moles (Talpa europaea L.) in comparison with undisturbed grassland soils. Field observations and soil sampling were carried out in the areas of eight settlements in the Klintsovskiy, Krasnogorskiy and Novozybkovskiy districts of the Bryansk region, Russia in six years during the period 1999-2016. The study sites had been heavily contaminated by Chernobyl fallout in 1986. Activity of 137 Cs in soil samples was determined by γ-ray spectrometry. 137 Cs surface ground contamination levels at the studied plots (n = 17) ranged from 327 kBq m -2 to 2360 kBq m -2 with a mean of 1000 kBq m -2 and a median of 700 kBq m -2 . The position of the 137 Cs migration centre in the soil in 2010-2016 was significantly (the Mann-Whitney U test, P < .01) deeper at mole-disturbed plots (median = 5.99 cm or 6.64 g cm -2 , n = 6) compared to the undisturbed ones (median = 2.48 cm or 2.35 g cm -2 , n = 6). The 137 Cs migration rate at mole-disturbed plots (median = 0.26 g cm -2  y -1 , mean = 0.31 g cm -2  y -1 ) was significantly higher (by a factor of 3) than at undisturbed plots (median = 0.08 g cm -2  y -1 , mean = 0.10 g cm -2  y -1 ). The difference in the migration rates between the mole-disturbed and undisturbed plots (median = 0.18 g cm -2  y -1 , mean = 0.21 g cm -2  y -1 ) reasonably corresponded to the mass of soil that might be ejected by moles per unit area per year. The results of this study indicate that the burrowing activity of moles has increased vertical migration of Chernobyl-derived radiocaesium in the grassland soils. Copyright © 2018 Elsevier Ltd. All rights reserved.

CORRELATIONS BETWEEN PESTICIDE TRANSFORMATION RATE AND MICROBIAL RESPIRATION ACTIVITY IN SOIL OF DIFFERENT ECOSYSTEMS

EPA Science Inventory

Cecil sandy loam soils (ultisol) from forest (coniferous and deciduous), pasture, and arable ecosystems were sampled (0-10 cm) in the vicinity of Athens, GA, USA. Soil from each site was subdivided into three portions, consisting of untreated soil (control) as well as live and s...

The method of UCN "small heating" measurement in the big gravitational spectrometer (BGS) and studies of this effect on Fomblin oil Y-HVAC 18/8.

PubMed

Nesvizhevsky, V V; Voronin, A Yu; Lambrecht, A; Reynaud, S; Lychagin, E V; Muzychka, A Yu; Nekhaev, G V; Strelkov, A V

2018-02-01

The Big Gravitational Spectrometer (BGS) takes advantage of the strong influence of the Earth's gravity on the motion of ultracold neutrons (UCNs) that makes it possible to shape and measure UCN spectra. We optimized the BGS to investigate the "small heating" of UCNs, that is, the inelastic reflection of UCNs from a surface accompanied by an energy change comparable with the initial UCN energy. UCNs whose energy increases are referred to as "Vaporized UCNs" (VUCNs). The BGS provides the narrowest UCN spectra of a few cm and the broadest "visible" VUCN energy range of up to ∼150 cm (UCN energy is given in units of its maximum height in the Earth's gravitational field, where 1.00 cm ≈ 1.02 neV). The dead-zone between the UCN and VUCN spectra is the narrowest ever achieved (a few cm). We performed measurements with and without samples without breaking vacuum. BGS provides the broadest range of temperatures (77-600 K) and the highest sensitivity to the small heating effect, up to ∼10 -8 per bounce, i.e., two orders of magnitude higher than the sensitivity of alternative methods. We describe the method to measure the probability of UCN "small heating" using the BGS and illustrate it with a study of samples of the hydrogen-free oil Fomblin Y-HVAC 18/8. The data obtained are well reproducible, do not depend on sample thickness, and do not evolve over time. The measured model-independent probability P + of UCN small heating from an energy "mono-line" 30.2 ± 2.5 cm to the energy range 35-140 cm is in the range 1.05±0.02 stat ×10 -5 -1.31±0.24 stat ×10 -5 at a temperature of 24 °C. The associated systematic uncertainty would disappear if a VUCN spectrum shape were known, for instance, from a particular model of small heating. This experiment provides the most precise and reliable value of small heating probability on Fomblin measured so far. These results are of importance for studies of UCN small heating as well as for analyzing and designing neutron lifetime experiments.

VizieR Online Data Catalog: ChaMP X-ray point source catalog (Kim+, 2007)

NASA Astrophysics Data System (ADS)

Kim, M.; Kim, D.-W.; Wilkes, B. J.; Green, P. J.; Kim, E.; Anderson, C. S.; Barkhouse, W. A.; Evans, N. R.; Ivezic, Z.; Karovska, M.; Kashyap, V. L.; Lee, M. G.; Maksym, P.; Mossman, A. E.; Silverman, J. D.; Tananbaum, H. D.

2009-01-01

We present the Chandra Multiwavelength Project (ChaMP) X-ray point source catalog with ~6800 X-ray sources detected in 149 Chandra observations covering ~10deg2. The full ChaMP catalog sample is 7 times larger than the initial published ChaMP catalog. The exposure time of the fields in our sample ranges from 0.9 to 124ks, corresponding to a deepest X-ray flux limit of f0.5-8.0=9x10-16ergs/cm2/s. The ChaMP X-ray data have been uniformly reduced and analyzed with ChaMP-specific pipelines and then carefully validated by visual inspection. The ChaMP catalog includes X-ray photometric data in eight different energy bands as well as X-ray spectral hardness ratios and colors. To best utilize the ChaMP catalog, we also present the source reliability, detection probability, and positional uncertainty. (10 data files).

Effect of Hops Beta Acids on the Survival of Unstressed- or Acid-Stress-Adapted-Listeria Monocytogenes and on the Quality and Sensory Attributes of Commercially Cured Ham Slices.

PubMed

Wang, Li; McKeith, Amanda Gipe; Shen, Cangliang; Carter, Kelsey; Huff, Alyssa; McKeith, Russell; Zhang, Xinxia; Chen, Zhengxing

2016-02-01

This study evaluated the antilisterial activity of hops beta acids (HBA) and their impact on the quality and sensory attributes of ham. Commercially cured ham slices were inoculated with unstressed- and acid-stress-adapted (ASA)-L. monocytogenes (2.2 to 2.5 log CFU/cm(2) ), followed by no dipping (control), dipping in deionized (DI) water, or dipping in a 0.11% HBA solution. This was followed by vacuum or aerobic packaging and storage (7.2 °C, 35 or 20 d). Samples were taken periodically during storage to check for pH changes and analyze the microbial populations. Color measurements were obtained by dipping noninoculated ham slices in a 0.11% HBA solution, followed by vacuum packaging and storage (4.0 °C, 42 d). Sensory evaluations were performed on ham slices treated with 0.05% to 0.23% HBA solutions, followed by vacuum packaging and storage (4.0 °C, 30 d). HBA caused immediate reductions of 1.2 to 1.5 log CFU/cm(2) (P < 0.05) in unstressed- and ASA-L. monocytogenes populations on ham slices. During storage, the unstressed-L. monocytogenes populations on HBA-treated samples were 0.5 to 2.0 log CFU/cm(2) lower (P < 0.05) than control samples and those dipped in DI water. The lag-phase of the unstressed-L. monocytogenes population was extended from 3.396 to 7.125 d (control) to 7.194 to 10.920 d in the HBA-treated samples. However, the ASA-L. monocytogenes population showed resistance to HBA because they had a higher growth rate than control samples and had similar growth variables to DI water-treated samples during storage. Dipping in HBA solution did not adversely affect the color or sensory attributes of the ham slices stored in vacuum packages. These results are useful for helping ready-to-eat meat processors develop operational procedures for applying HBA on ham slices. © 2016 Institute of Food Technologists®

A hot implantation study on the evolution of defects in He ion implanted MgO(1 0 0)

NASA Astrophysics Data System (ADS)

Fedorov, A. V.; van Huis, M. A.; van Veen, A.

2002-05-01

Ion implantation at elevated temperature, so-called hot implantation, was used to study nucleation and thermal stability of the defects. In this work, MgO(1 0 0) single crystal samples were implanted with 30 keV He ions at various implantation temperatures. The implantation doses ranged from 10 14 to 10 16 cm -2. The implantation introduced defects were subsequently studied by thermal helium desorption spectroscopy (THDS) and Doppler broadening positron beam analysis (PBA). The THDS study provides vital information on the kinetics of He release from the sample. PBA technique, being sensitive to the open volume defects, provides complementary information on cavity evolution. The THD study has shown that in most cases helium release is characterised by the activation energy of Q=4.7±0.5 eV with the maximum release temperature of Tmax=1830 K. By applying first order desorption model the pre-exponent factor is estimated as ν=4.3×10 11 s -1.

High discharge efficiency of (Sr, Pb, Bi) TiO3 relaxor ceramics for energy-storage application

NASA Astrophysics Data System (ADS)

Chao, Mingming; Liu, Jingsong; Zeng, Mengshi; Wang, Debin; Yu, Hongtao; Yuan, Ying; Zhang, Shuren

2018-05-01

We report herein on the energy storage and discharge properties of the relaxor ferroelectric ceramic Sr0.8Pb0.1Bi0.1TiO3 (SPBT). This material has a slanted hysteresis loop, and all samples show low remnant polarization and low coercive field, which leads to a high discharge efficiency. The maximum polarization is 10.1 μC/cm2, the minimum coercive field is 0.229 kV/cm, and the maximum efficiency is 94.2%. The discharge current waveforms are sinusoidal, the first discharge period is 140 ns, and the power density is approximately 4.2 × 107 W/kg. The high discharge speed and high discharge power density indicate that SPBT ceramics are very promising materials for energy storage applications.

Monitoring 2-ethylhexyl-4-methoxycinnamate photoisomerization on skin using attenuated total reflection fourier transform infrared spectroscopy.

PubMed

Pangnakorn, P; Nonthabenjawan, R; Ekgasit, S; Thammacharoen, C; Pattanaargson Wanichwecharungruang, S

2007-02-01

Photoisomerization and photodimerization of a widely used UVB filter, 2-ethylhexy-4-methoxycinnamate (EHMC) on a ZnSe surface and baby mouse (Mus musculus Linn.) skin were monitored using attenuated total reflection Fourier transform infrared spectroscopy (ATR-FT-IR). Differentiation between the E- and the Z-EHMC could be achieved by examining the infrared (IR) peak at 981 cm(-1) (b peak), which corresponds to the CH rocking deformation vibration of Ph-CH=CH- detected only in the E configuration. By plotting the ratios of the peak area of the b peak and an internal standard peak (1060-998 cm(-1)) against mole percentage of Z-isomer in the E-Z mixtures, a linear calibration plot was obtained. Thus, a simple estimation of the mole percentage of each configuration in a sample was obtained. At the same UVB exposure, photostationary equilibrium of the E/Z isomerization on the surface varied with the applied amounts of EHMC. Photoisomerizations on ZnSe and on baby mouse skin were comparable. Less than 10% of E-EHMC changed configuration when the mouse skins applied with 1.0-4.0 mg/cm(2) E-EHMC were exposed to sunlight for 60 min (UVB radiant exposure of approximately 0.30 J/cm(2)). This corresponded to less than 5% loss in UV filtering efficiency. However, at a typical EHMC skin coverage ( approximately 0.2 mg/cm(2)), 0.30 J/cm(2) UVB exposure induced approximately 50% photoisomerization resulting in 25% loss of UV filtering efficiency. No photodimerization was detected even at the extreme EHMC coverage of 4.0 mg/cm(2) after a UVB exposure of 0.90 J/cm(2).

Transport, Optical, and Magnetic Properties of the Conducting Halide Perovskite CH 3NH 3SnI 3

NASA Astrophysics Data System (ADS)

Mitzi, D. B.; Feild, C. A.; Schlesinger, Z.; Laibowitz, R. B.

1995-01-01

A low-temperature ( T ≤ 100°C) solution technique is described for the preparation of polycrystalline and single crystal samples of the conducting halide perovskite, CH 3NH 3SnI 3. Transport, Hall effect, magnetic, and optical properties are examined over the temperature range 1.8-300 K, confirming that this unusual conducting halide perovskite is a low carrier density p-type metal with a Hall hole density, 1/ RHe ≃ 2 × 10 19 cm -3. The resistivity of pressed pellet samples decreases with decreasing temperature with resistivity ratio ρ(300 K)/ρ(2 K) ≃ 3 and room temperature resistivity ρ(300 K) ≃ 7 mΩ-cm. A free-carrier infrared reflectivity spectrum with a plasma edge observed at approximately 1600 cm -1 further attests to the metallic nature of this compound and suggests a small optical effective mass, m* ≃ 0.2.

Long-term ecological effects of exposure to uranium

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hanson, W.C.; Miera, F.R. Jr.

1976-03-01

The consequences of releasing natural and depleted uranium to terrestrial ecosystems during development and testing of depleted uranium munitions were investigated. At Eglin Air Force Base, Florida, soil at various distances from armor plate target butts struck by depleted uranium penetrators was sampled. The upper 5 cm of soil at the target bases contained an average of 800 ppM of depleted uranium, about 30 times as much as soil at 5- to 10-cm depth, indicating some vertical movement of depleted uranium. Samples collected beyond about 20 m from the targets showed near-background natural uranium levels, about 1.3 +- 0.3 ..mu..g/gmore » or ppM. Two explosives-testing areas at the Los Alamos Scientific Laboratory (LASL) were selected because of their use history. E-F Site soil averaged 2400 ppM of uranium in the upper 5 cm and 1600 ppM at 5-10 cm. Lower Slobovia Site soil from two subplots averaged about 2.5 and 0.6 percent of the E-F Site concentrations. Important uranium concentration differences with depth and distance from detonation points were ascribed to the different explosive tests conducted in each area. E-F Site vegetation samples contained about 320 ppM of uranium in November 1974 and about 125 ppM in June 1975. Small mammals trapped in the study areas in November contained a maximum of 210 ppM of uranium in the gastrointestinal tract contents, 24 ppM in the pelt, and 4 ppM in the remaining carcass. In June, maximum concentrations were 110, 50, and 2 ppM in similar samples and 6 ppM in lungs. These data emphasized the importance of resuspension of respirable particles in the upper few millimeters of soil as a contamination mechanism for several components of the LASL ecosystem.« less

Assessment of Fluoride Concentration of Soil and Vegetables in Vicinity of Zinc Smelter, Debari, Udaipur, Rajasthan

PubMed Central

Bhat, Nagesh; Asawa, Kailash; Tak, Mridula; Shinde, Kushal; Singh, Anukriti; Gandhi, Neha; Gupta, Vivek Vardhan

2015-01-01

Background As of late, natural contamination has stimulated as a reaction of mechanical and other human exercises. In India, with the expanding industrialization, numerous unsafe substances are utilized or are discharged amid generation as cleans, exhaust, vapours and gasses. These substances at last are blended in the earth and causes health hazards. Objective To determine concentration of fluoride in soils and vegetables grown in the vicinity of Zinc Smelter, Debari, Udaipur, Rajasthan. Materials and Methods Samples of vegetables and soil were collected from areas situated at 0, 1, 2, 5, and 10 km distance from the zinc smelter, Debari. Three samples of vegetables (i.e. Cabbage, Onion and Tomato) and 3 samples of soil {one sample from the upper layer of soil (i.e. 0 to 20 cm) and one from the deep layer (i.e. 20 – 40 cm)} at each distance were collected. The soil and vegetable samples were sealed in clean polythene bags and transported to the laboratory for analysis. One sample each of water and fertilizer from each distance were also collected. Results The mean fluoride concentration in the vegetables grown varied between 0.36 ± 0.69 to 0.71 ± 0.90 ppm. The fluoride concentration in fertilizer and water sample from various distances was found to be in the range of 1.4 – 1.5 ppm and 1.8 – 1.9 ppm respectively. Conclusion The fluoride content of soil and vegetables was found to be higher in places near to the zinc smelter. PMID:26557620

Ion irradiation of ternary pyrochlore oxides.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lumpkin, G. R.; Smith, K. L.; Blackford, M. G.

2009-05-01

Polycrystalline synthetic samples of Y{sub 2}Ti{sub 2-x}Sn{sub x}O{sub 7} with x = 0.4, 0.8, 1.2, and 1.6, together with Nd{sub 2}Zr{sub 2}O{sub 7}, Nd{sub 2}Zr{sub 1.2}Ti{sub 0.8}O{sub 7}, and La{sub 1.6}Y{sub 0.4}Hf{sub 2}O{sub 7}, were irradiated in situ in the intermediate voltage electron microscope (IVEM)-Tandem Facility at Argonne National Laboratory using 1.0 MeV Kr ions at temperatures of 50 to 650 K. Determination of the critical amorphization fluence (F{sub c}) as a function of temperature has revealed a dramatic increase in radiation tolerance with increasing Sn content on the pyrochlore B site. Nonlinear least-squares analysis of the fluence-temperature curves gavemore » critical temperatures (T{sub c}) of 666 {+-} 4, 335 {+-} 12, and 251 {+-} 51 K for the Y{sub 2}Ti{sub 2-x}Sn{sub x}O{sub 7} samples with x = 0.4, 0.8, and 1.2, respectively. The sample with x = 1.6 appears to disorder to a defect fluorite structure at a fluence below 1.25 x 10{sup 15} ions cm{sup -2} and remains crystalline to 5 x 10{sup 15} ions cm{sup -2} at 50 K. Additionally, the critical fluence-temperature response curves were determined for Nd{sub 2}Zr{sub 1.2}Ti{sub 0.8}O{sub 7} and La{sub 1.6}Y{sub 0.4}Hf{sub 2}O{sub 7}, and we obtained T{sub c} values of 685 {+-} 53 K and 473 {+-} 52 K, respectively, for these pyrochlores. Nd{sub 2}Zr{sub 2}O{sub 7} did not become amorphous after a fluence of 2.5 x 10{sup 15} ions cm{sup -2} at 50 K, but there is evidence that it may amorphize at a higher fluence, with an estimated T{sub c} of 135 K. The observed T{sub c} results are discussed with respect to the predicted T{sub c} values based upon a previously published empirical model (Lumpkin, G. R.; Pruneda, M.; Rios, S.; Smith, K. L.; Trachenko, K.; Whittle, K. R.; Zaluzec, N. J. J. Solid State Chem. 2007, 180, 1512). In the Y{sub 2}Ti{sub 2-x}Sn{sub x}O{sub 7} pyrochlores, T{sub c} appears to be linear with respect to composition, and is linear with respect to r{sub A}/r{sub B} and x(48f) for all samples investigated herein.« less

FTIR characterization of animal lung cells: normal and precancerous modified e10 cell line

NASA Astrophysics Data System (ADS)

Zezell, D. M.; Pereira, T. M.; Mennecier, G.; Bachmann, L.; Govone, A. B.; Dagli, M. L. Z.

2012-06-01

The chemical carcinogens from tobacco are related to over 90% of lung cancers around the world. The risk of death of this kind of cancer is high because the diagnosis usually is made only in advanced stages. Therefore, it is necessary to develop new diagnostic methods for detecting the lung cancer in earlier stages. The Fourier Transform Infrared Spectroscopy (FTIR) can offer high sensibility and accuracy to detect the minimal chemical changes into the biological sample. The aim of this study is to evaluate the differences on infrared spectra between normal lung cells and precancerous lung cells transformed by NNK. Non-cancerous lung cell line e10 (ATCC) and NNK-transformed e10 cell lines were maintained in complete culture medium (1:1 mixture of Dulbecco's modified Eagle's medium and Ham's F12 [DMEM/Ham's F12], supplemented with 100 ng/ml cholera enterotoxin, 10 lg/ml insulin, 0.5 lg/ml. hydrocortisol, 20 ng/ml epidermal growth factor, and 5% horse serum. The cultures were maintained in alcohol 70%. The infrared spectra were acquired on ATR-FTIR Nicolet 6700 spectrophotometer at 4 cm-1 resolution, 30 scans, in the 1800-900 cm-1 spectral range. Each sample had 3 spectra recorded, 30 infrared spectra were obtained from each cell line. The second derivate of spectra indicates that there are displacement in 1646 cm-1 (amine I) and 1255 cm-1(DNA), allowing the possibility to differentiate the two king of cells, with accuracy of 89,9%. These preliminary results indicate that ATR-FTIR is useful to differentiate normal e10 lung cells from precancerous e10 transformed by NNK.

Effect of double homogenization and whey protein concentrate on the texture of ice cream.

PubMed

Ruger, P R; Baer, R J; Kasperson, K M

2002-07-01

Ice cream samples were made with a mix composition of 11% milk fat, 11% milk solids-not-fat, 13% sucrose, 3% corn syrup solids (36 dextrose equivalent), 0.28% stabilizer blend, or 0.10% emulsifier and vanilla extract. Mixes were high temperature short time pasteurized at 80 degrees C for 25 s, homogenized at 141 kg/cm2 pressure on the first stage and 35 kg/cm2 pressure on the second, and cooled to 3 degrees C. The study included six treatments from four batches of mix. Mix from batch one contained 0.10% emulsifier. Half of this batch (treatment 1), was subsequently frozen and the other half (upon exiting the pasteurizer) was reheated to 60 degrees C, rehomogenized at 141 kg/cm2 pressure on the first stage and 35 kg/cm2 pressure on the second (treatment 2), and cooled to 3 degrees C. Mix from batch two contained 0.28% stabilizer blend. Half of this batch was used as the control (treatment 3), the other half upon exiting the pasteurizer was reheated to 60 degrees C, rehomogenized at 141 kg/cm2 pressure on the first stage and 35 kg/cm2 pressure on the second (treatment 4), and cooled to 3 degrees C. Batch three, containing 0.10% emulsifier and 1% whey protein concentrate substituted for 1% nonfat dry milk, upon exiting the pasteurizer was reheated to 60 degrees C, rehomogenized at 141 kg/cm2 pressure on the first stage and 35 kg/cm2 pressure on the second (treatment 5), and cooled to 3 degrees C. Batch four, containing 0.28% stabilizer blend and 1% whey protein concentrate substituted for 1% nonfat dry milk, upon exiting the pasteurizer was reheated to 60 degrees C, rehomogenized at 141 kg/ cm2 pressure on the first stage and 35 kg/cm2 pressure on the second (treatment 6), and cooled to 3 degrees C. Consistency was measured by flow time through a pipette. Flow time of treatment 3 was greater than all treatments, and the flow times of treatments 4 and 6 were greater than treatments 1, 2, and 5. Flow time was increased in ice cream mix by the addition of stabilizer. Double homogenization lowered ice cream mix flow time in the presence of stabilizer, but no difference in flow time was observed without stabilizer addition. Treatment 4 had a lower mean ice crystal size at 10 d postmanufacture compared with treatment 3; however, overall texture acceptability between treatments 3 and 4 was similar. Mean ice crystal size of treatment 6 was less at 18 wk postmanufacture compared with treatment 3; however, overall texture acceptability for treatments 3, 4, and 6 was similar. Mean ice crystal sizes of treatments 1, 2, and 5 were greater at 10 d and 18 wk compared with treatment 3. Sensory evaluation indicated that treatments 3, 4, and 6 had higher mean scores for icy, coldness intensity, and creaminess than treatments 1, 2, and 5 at 10 d and 18 wk postmanufacture.

[Recovery of Trichostrongylus colubriformis infective larvae from three grass species contaminated in summer].

PubMed

Rocha, Raquel A da; Rocha, Gilberto P da; Bricarello, Patrizia A; Amarante, Alessandro F T

2008-01-01

The purpose of the experiment was to evaluate infective Trichostrongylus colubriformis larvae (L3) survival in three forage species. Experimental plots, planted with Brachiaria decumbens cv. Australian, Cynodon dactilon cv. Coast-cross, and Panicum maximum cv. Aruana, were used in the study, totaling two plots for each species. Each plot (32.4 m(2)) was divided into 36 subplots (30 x 30 cm) in order to allow six replicates per forage species and per herbage height in each week of material collection. Larval recovery was evaluated from middle summer to middle autumn under the effect of two forage paring heights: low, 5 cm, and high, 30 cm. The paring was carried out immediately before the fecal samples with T. colubriformis eggs, taken from sheep, were deposited on pasture in 05/Feb/2004. Feces and forage collection was performed one, two, four, eight, 12 and 16 weeks after feces deposition in the experimental plots. Forage grass height was measured in each subdivision immediately before the collections. The forage sample was cut, close to the soil, from an area delimited with a circle with a 10 cm radius. The feces were collected from the subplots. The number of infective larvae recovered from pasture was very small in comparison with the amount of larvae produced in cultures maintained in laboratory (maximum 6.7% on Aruana grass with 30 cm). L3 recovery rates from fecal samples were bigger when the feces were deposited on high grass (measuring 30 cm - P<0.05). L3 recovery from pasture and L3 concentration on herbage (L3/Kg dry matter) were similar for both cuts (P>0.05). Among the forage species, the Aruana grass was the one that, in general, harbored the biggest concentrations of infective T. colubriformis larvae.

40 CFR 761.304 - Determining sample location.

Code of Federal Regulations, 2010 CFR

2010-07-01

.... (a) For 1 square meter non-porous surface areas having the same size and shape, it is permissible to sample the same 10 cm by 10 cm location or position in each identical 1 square meter area. This location or position is determined in accordance with § 761.306 or § 761.308. (b) If some 1 square meter...

40 CFR 761.304 - Determining sample location.

Code of Federal Regulations, 2013 CFR

2013-07-01

.... (a) For 1 square meter non-porous surface areas having the same size and shape, it is permissible to sample the same 10 cm by 10 cm location or position in each identical 1 square meter area. This location or position is determined in accordance with § 761.306 or § 761.308. (b) If some 1 square meter...

40 CFR 761.304 - Determining sample location.

Code of Federal Regulations, 2011 CFR

2011-07-01

.... (a) For 1 square meter non-porous surface areas having the same size and shape, it is permissible to sample the same 10 cm by 10 cm location or position in each identical 1 square meter area. This location or position is determined in accordance with § 761.306 or § 761.308. (b) If some 1 square meter...

40 CFR 761.304 - Determining sample location.

Code of Federal Regulations, 2014 CFR

2014-07-01

.... (a) For 1 square meter non-porous surface areas having the same size and shape, it is permissible to sample the same 10 cm by 10 cm location or position in each identical 1 square meter area. This location or position is determined in accordance with § 761.306 or § 761.308. (b) If some 1 square meter...

40 CFR 761.304 - Determining sample location.

Code of Federal Regulations, 2012 CFR

2012-07-01

.... (a) For 1 square meter non-porous surface areas having the same size and shape, it is permissible to sample the same 10 cm by 10 cm location or position in each identical 1 square meter area. This location or position is determined in accordance with § 761.306 or § 761.308. (b) If some 1 square meter...

Shelf life extension of ricotta cheese using coatings of galactomannans from nonconventional sources incorporating nisin against Listeria monocytogenes.

PubMed

Martins, Joana T; Cerqueira, Miguel A; Souza, Bartolomeu W S; Carmo Avides, Maria do; Vicente, António A

2010-02-10

Shelf life extension of Ricotta cheese was evaluated at 4 degrees C upon the use of edible coatings made of galactomannans from Gleditsia triacanthos incorporating nisin against Listeria monocytogenes. Three different treatments were tested in cheese: samples without coating; samples with coating without nisin; and samples with coating containing 50 IU x g(-1) of nisin. To test the effectiveness of the treatments against L. monocytogenes, the surface of the cheese was inoculated with a suspension of the microorganism. Microbiological and physical-chemical analyses of the cheese samples were performed during 28 days. Results showed that the cheese coated with nisin-added galactomannan film was the treatment presenting the best results in terms of microbial growth delay (p < 0.05). The addition of nisin also affects (p < 0.05) the physical and mechanical properties of the films: O(2) permeability decreased from 1.84 to 1.35 x 10(-12) cm(3) x (Pa x s x m)(-1); CO(2) permeability increased from 1.96 to 6.31 x 10(-12) cm(3).(Pa x s x m)(-1); opacity increased from 3.68 to 4.59%; tensile strength ranged from 0.84 to 1.46 MPa; and elongation at break improved from 50.93 to 68.16%. These results demonstrate that novel galactomannan-based edible coatings, when combined with nisin, may provide consumer-friendly alternatives to reduce L. monocytogenes postcontamination on cheese products during storage.

Soil moisture variation patterns observed in Hand County, South Dakota

NASA Technical Reports Server (NTRS)

Jones, E. B.; Owe, M.; Schmugge, T. J. (Principal Investigator)

1981-01-01

Soil moisture data were taken during 1976 (April, June, October), 1977 (April, May, June), and 1978 (May, June, July) Hand County, South Dakota as part of the ground truth used in NASA's aircraft experiments to study the use of microwave radiometers for the remote sensing of soil moisture. The spatial variability observed on the ground during each of the sampling events was studied. The data reported are the mean gravimetric soil moisture contained in three surface horizon depths: 0 to 2.5, 0 to 5 and 0 to 10 cm. The overall moisture levels ranged from extremely dry conditions in June 1976 to very wet in May 1978, with a relatively even distribution of values within that range. It is indicated that well drained sites have to be partitioned from imperfectly drained areas when attempting to characterize the general moisture profile throughout an area of varying soil and cover type conditions. It is also found that the variability in moisture content is greatest in the 0 to 2.5 cm measurements and decreases as the measurements are integrated over a greater depth. It is also determined that the sampling intensity of 10 measurements per km is adequate to estimate the mean moisture with an uncertainty of + or - 3 percent under average moisture conditions in areas of moderate to good drainage.

Influence of Pectin as a green polymer electrolyte on the transport properties of Chitosan-Pectin membranes.

PubMed

Pasini Cabello, S D; Ochoa, N A; Takara, E A; Mollá, S; Compañ, V

2017-02-10

Novel blend membranes have been prepared from Chitosan (CH), Pectin (PEC) and their mixtures. The obtained samples were cross-linked and sulfonated before characterization. The results show that CH/PEC membranes display structural changes on the chemical and physical properties as a function of composition. DSC analysis reveals an endothermic peak due to the scission of the ionic pairs between carboxylic groups and ammonium groups, which produces a strong change on physical properties such as methanol permeability and proton conductivity. The methanol permeability decreases with the amount of Pectin from (4.24±0.04)×10 -6 cm 2 /s for pure Chitosan membrane to (1.51±0.03)×10 -6 cm 2 /s for blend CH/PEC membranes when the amount of Pectin is 50% (v/v). The proton conductivities of the blend membranes follow a similar behavior. For a pure CH membrane the conductivity is 2.44×10 -3 S/cm, decreasing with pectin content until the composition 50/50 (v/v), in which the conductivity drops almost one order of magnitude. Copyright © 2016 Elsevier Ltd. All rights reserved.

Synthesis and Behavior of Cetyltrimethyl Ammonium Bromide Stabilized Zn1+xSnO3+x (0 ≤ x ≤1) Nano-Crystallites

PubMed Central

Placke, Astrid; Kumar, Ashok; Priya, Shashank

2016-01-01

We report synthesis of cetyltrimethyl ammonium bromide (CTAB) stabilized Zn1+xSnO3+x (0 ≤ x ≤1) nano-crystallites by facile cost-effective wet chemistry route. The X-ray diffraction patterns of as-synthesized powders at the Zn/Sn ratio of 1 exhibited formation of ZnSn(OH)6. Increasing the Zn/Sn ratio further resulted in the precipitation of an additional phase corresponding to Zn(OH)2. The decomposition of these powders at 650°C for 3h led to the formation of the orthorhombic phase of ZnSnO3 and tetragonal SnO2-type phase of Zn2SnO4 at the Zn/Sn ratio of 1 and 2, respectively, with the formation of their mixed phases at intermediate compositions, i.e., at Zn/Sn ratio of 1.25, 1.50 and 1.75, respectively. The lattice parameters of orthorhombic and tetragonal phases were a ~ 3.6203 Å, b ~ 4.2646 Å and c ~ 12.8291Å (for ZnSnO3) and a = b ~ 5.0136 Å and c ~ 3.3055Å (for Zn2SnO4). The transmission electron micrographs revealed the formation of nano-crystallites with aspect ratio ~ 2; the length and thickness being 24, 13 nm (for ZnSnO3) and 47, 22 nm (for Zn2SnO4), respectively. The estimated direct bandgap values for the ZnSnO3 and Zn2SnO4 were found to be 4.21 eV and 4.12 eV, respectively. The ac conductivity values at room temperature (at 10 kHz) for the ZnSnO3 and Zn2SnO4 samples were 8.02 × 10−8 Ω-1 cm-1 and 6.77 × 10−8 Ω-1 cm-1, respectively. The relative permittivity was found to increase with increase in temperature, the room temperature values being 14.24 and 25.22 for the samples ZnSnO3 and Zn2SnO4, respectively. Both the samples, i.e., ZnSnO3 and Zn2SnO4, exhibited low values of loss tangent up to 300 K, the room temperature values being 0.89 and 0.72, respectively. A dye-sensitized solar cell has been fabricated using the optimized sample of zinc stannate photo-anode, i.e., Zn2SnO4. The cyclic voltammetry revealed oxidation and reduction around 0.40 V (current density ~ 11.1 mA/cm2) and 0.57 V (current density– 11.7 mA/cm2) for Zn2SnO4 photo-anode in presence of light. PMID:27228102

Comparative performance of contact plates, electrostatic wipes, swabs and a novel sampling device for the detection of Staphylococcus aureus on environmental surfaces.

PubMed

Lutz, J K; Crawford, J; Hoet, A E; Wilkins, J R; Lee, J

2013-07-01

To evaluate the performance of four sampling methods [contact plates, electrostatic wipes (wipe), swabs and a novel roller sampler] for recovery of Staphylococcus aureus from a stainless steel surface. Stainless steel test plates were inoculated with Staph. aureus, dried for 24 h and sampled using each of the four methods. Samples were either incubated directly (roller, contact plate) or processed using elution and membrane filtration (swab, wipe). Performance was assessed by calculating the apparent sampling efficiency (ASE), analytical sensitivity (Sn) and percentage of replications with positive growth. The wipe demonstrated the best performance across all inoculating concentrations (ASE(48 h) = 18%; Sn(48 h) = 7 CFU per 100 cm(2)). The swab performed well when corrected for area actually sampled (ASE(48 h) = 24%; Sn(48 h) = 76 CFU per 100 cm(2)). Of the contact-based methods, the newly developed roller sampler outperformed the contact plate (roller: ASE(48 h) = 10%; Sn(48 h) = 17 CFU per 100 cm(2); contact plate: ASE(48 h) = 0·04%; Sn(48 h) = 1412 CFU per 100 cm(2)); both contact samplers performed better at higher inoculating concentrations (6E3 CFU per 100 cm(2) for the roller and 6E6 CFU per 100 cm(2) for the contact plate). Overall, the electrostatic wipe produced the highest number of replications resulting in positive growth (74%(24 h), 91%(48 h)). This study demonstrates that selection of the sampling method must be carefully considered, given that different methods have varying performance. This is the first study assessing static wipes for sampling and one that uses a more real-world-relevant 24-h drying time. The results help with infection control, and environmental health professionals choose better sampling methodologies. Journal of Applied Microbiology © 2013 The Society for Applied Microbiology.

P-type conductivity in annealed strontium titanate

DOE PAGES

Poole, Violet M.; Corolewski, Caleb D.; McCluskey, Matthew D.

2015-12-17

In this study, Hall-effect measurements indicate p-type conductivity in bulk, single-crystal strontium titanate (SrTiO 3, or STO) samples that were annealed at 1200°C. Room temperature mobilities above 100 cm 2/Vs were measured, an order of magnitude higher than those for electrons (5-10 cm 2/Vs). Average hole densities were in the 10 9-10 10 cm -3 range, consistent with a deep acceptor.

Synthesis of Polyurethanes Membranes from Rubber Seed Oil and Methylene Diphenyl Diisocyanates (MDI)

NASA Astrophysics Data System (ADS)

Marlina; Nurman, S.; Saleha, S.; Fitriani; Thanthawi, I.

2017-03-01

Rubber seed oil and methylene diphenyl diisocyanates (MDI) based polyurethane membrane has been prepared in this study. The main objective of this research is manufacture of polyurethane membranes from avocado seed oil, as a filter of this membrane use as a filter of metals from water such as mercury (Hg). In this study, the polyurethane membrane had been synthesized by varying compositions of rubber seed oil and MDI, with ratios of 10:0.2; 10:0.4; 10:0.6; 10:0.8; 10:1.0; 10:1.2; 10:1.4; 10:1.6; 10:1.8 and 10:2.0 (v/w) at 80°C and 170°C as polymerization and curing temperatures, respectively. Optimum polyurethane membrane was obtained at rubber seed oil: MDI 10: 0.8 v/w, it was dry, non-sticky, smooth and blackish brown. The membrane flux was 5,8307 L / m2.h.bar and rejection factor was 35,3015 %. The results of characterization indicated the formation of urethane bonds (NH at 3480 cm-1, C=O at 1620 cm-1, CN at 1374 cm-1, -OC-NH- at 1096 cm-1 and no -NCO at 2270 cm-1), the value of Tg was 55°C. The polyurethane membrane which treated at the optimum treatment conditions were used to the filter of metals from water such as mercury (Hg).

Wound healing efficacy of a 660-nm diode laser in a rat incisional wound model.

PubMed

Suzuki, Ryoichi; Takakuda, Kazuo

2016-11-01

This study aimed to elucidate the optimum usage parameters of low reactive-level laser therapy (LLLT) in a rat incisional wound model. In Sprague-Dawley rats, surgical wounds of 15-mm length were made in the dorsal thoracic region. They were divided into groups to receive 660-nm diode laser irradiation 24 h after surgery at an energy density of 0 (control), 1, 5, or 10 J/cm 2 . Tissue sections collected on postoperative day 3 were stained with hematoxylin-eosin and an antibody for ED1 to determine the number of macrophages around the wound. Samples collected on day 7 were stained with hematoxylin-eosin and observed via polarized light microscopy to measure the area occupied by collagen fibers around the wound; day 7 skin specimens were also subjected to mechanical testing to evaluate tensile strength. On postoperative day 3, the numbers of macrophages around the wound were significantly lower in the groups receiving 1 and 5 J/cm 2 irradiation, compared to the control and 10 J/cm 2 irradiation groups (p < 0.01). The area occupied by collagen fibers in day 7 was largest in 5 J/cm 2 group, followed by 1 J/cm 2 group, although this difference was not significant. The day 7 tensile test demonstrated significantly greater rupture strength in healing tissues from 1 and 5 J/cm 2 irradiation groups, compared to the control group (p < 0.05). Thus, LLLT with a 660-nm diode laser with energy density of 1 and 5 J/cm 2 enhanced wound healing in a rat incisional wound model. However, a higher radiation energy density yielded no significant enhancement.

Responses of Soil Microbial Communities to Experimental Warming in Alpine Grasslands on the Qinghai-Tibet Plateau

PubMed Central

He, Xingyuan; Liu, Wenjie; Zhao, Qian; Zhao, Lin; Tian, Chunjie

2014-01-01

Global surface temperature is predicted to increase by at least 1.5°C by the end of this century. However, the response of soil microbial communities to global warming is still poorly understood, especially in high-elevation grasslands. We therefore conducted an experiment on three types of alpine grasslands on the Qinghai-Tibet Plateau to study the effect of experimental warming on abundance and composition of soil microbial communities at 0–10 and 10–20 cm depths. Plots were passively warmed for 3 years using open-top chambers and compared to adjacent control plots at ambient temperature. Soil microbial communities were assessed using phospholipid fatty acid (PLFA) analysis. We found that 3 years of experimental warming consistently and significantly increased microbial biomass at the 0–10 cm soil depth of alpine swamp meadow (ASM) and alpine steppe (AS) grasslands, and at both the 0–10 and 10–20 cm soil depths of alpine meadow (AM) grasslands, due primarily to the changes in soil temperature, moisture, and plant coverage. Soil microbial community composition was also significantly affected by warming at the 0–10 cm soil depth of ASM and AM and at the 10–20 cm soil depth of AM. Warming significantly decreased the ratio of fungi to bacteria and thus induced a community shift towards bacteria at the 0–10 cm soil depth of ASM and AM. While the ratio of arbuscular mycorrhizal fungi to saprotrophic fungi (AMF/SF) was significantly decreased by warming at the 0–10 cm soil depth of ASM, it was increased at the 0–10 cm soil depth of AM. These results indicate that warming had a strong influence on soil microbial communities in the studied high-elevation grasslands and that the effect was dependent on grassland type. PMID:25083904

Increased p-type conductivity through use of an indium surfactant in the growth of Mg-doped GaN

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kyle, Erin C. H., E-mail: erinkyle@engineering.ucsb.edu; Kaun, Stephen W.; Young, Erin C.

2015-06-01

We have examined the effect of an indium surfactant on the growth of p-type GaN by ammonia-based molecular beam epitaxy. p-type GaN was grown at temperatures ranging from 700 to 780 °C with and without an indium surfactant. The Mg concentration in all films in this study was 4.5–6 × 10{sup 19} cm{sup −3} as measured by secondary ion mass spectroscopy. All p-type GaN films grown with an indium surfactant had higher p-type conductivities and higher hole concentrations than similar films grown without an indium surfactant. The lowest p-type GaN room temperature resistivity was 0.59 Ω-cm, and the highest room temperature carrier concentration wasmore » 1.6 × 10{sup 18} cm{sup −3}. Fits of the temperature-dependent carrier concentration data showed a one to two order of magnitude lower unintentional compensating defect concentration in samples grown with the indium surfactant. Samples grown at higher temperature had a lower active acceptor concentration. Improvements in band-edge luminescence were seen by cathodoluminescence for samples grown with the indium surfactant, confirming the trends seen in the Hall data.« less

Minority carrier lifetime in iodine-doped molecular beam epitaxy-grown HgCdTe

DOE Office of Scientific and Technical Information (OSTI.GOV)

Madni, I.; Umana-Membreno, G. A.; Lei, W.

2015-11-02

The minority carrier lifetime in molecular beam epitaxy grown layers of iodine-doped Hg{sub 1−x}Cd{sub x}Te (x ∼ 0.3) on CdZnTe substrates has been studied. The samples demonstrated extrinsic donor behavior for carrier concentrations in the range from 2 × 10{sup 16} cm{sup −3} to 6 × 10{sup 17} cm{sup −3} without any post-growth annealing. At a temperature of 77 K, the electron mobility was found to vary from 10{sup 4} cm{sup 2}/V s to 7 × 10{sup 3} cm{sup 2}/V s and minority carrier lifetime from 1.6 μs to 790 ns, respectively, as the carrier concentration was increased from 2 × 10{sup 16} cm{supmore » −3} to 6 × 10{sup 17} cm{sup −3}. The diffusion of iodine is much lower than that of indium and hence a better alternative in heterostructures such as nBn devices. The influence of carrier concentration and temperature on the minority carrier lifetime was studied in order to characterize the carrier recombination mechanisms. Measured lifetimes were also analyzed and compared with the theoretical models of the various recombination processes occurring in these materials, indicating that Auger-1 recombination was predominant at higher doping levels. An increase in deep-level generation-recombination centers was observed with increasing doping level, which suggests that the increase in deep-level trap density is associated with the incorporation of higher concentrations of iodine into the HgCdTe.« less

Efficacies of soy sauce and wine base marinades for controlling spoilage of raw beef.

PubMed

Kargiotou, C; Katsanidis, E; Rhoades, J; Kontominas, M; Koutsoumanis, K

2011-02-01

Fresh beef slices were marinated by immersion in marinades based on soy sauce without (SB) or with lactic acid (SBLA) or red wine base without (WB) or with 0.5% v/v oregano essential oil (WBO). For control samples (immersed in saline), a mean increase of 0.9log CFU/cm(2) in total viable counts (TVCs) occurred during the 24h treatment. During marination with WB and SB, mean TVC decreased by 0.7 and 0.3log CFU/cm(2), respectively. The mean decrease in TVC for samples marinated in WBO or SBLA was 1.2log CFU/cm(2). Subsequent storage of beef resulted in a rapid increase of TVC in control samples, to ≥9.5log CFU/cm(2) after 8 days at 5°C or 3 days at 15°C. Significant (P<0.05) microbial growth occurred in marinated samples stored at 5°C. During storage at 15°C TVC increased in only WB samples but the final numbers of 5.9log CFU/cm(2) were significantly lower (P<0.05) than the numbers in the control. Results similar to those for TVC were observed for Pseudomonas spp. All marinades also gave meat with significant lower TBARS values than the controls. There were no significant differences (P>0.05) in the toughness of the marinated samples compared to the control, except for SBLA samples which had significantly higher (P<0.05) shear force values. Marination with soy sauce or red wine marinades can evidently control microbial spoilage and oxidation of meat. Copyright © 2010 Elsevier Ltd. All rights reserved.

Commissioning of a PTW 34070 large-area plane-parallel ionization chamber for small field megavoltage photon dosimetry.

PubMed

Kupfer, Tom; Lehmann, Joerg; Butler, Duncan J; Ramanathan, Ganesan; Bailey, Tracy E; Franich, Rick D

2017-11-01

This study investigates a large-area plane-parallel ionization chamber (LAC) for measurements of dose-area product in water (DAP w ) in megavoltage (MV) photon fields. Uniformity of electrode separation of the LAC (PTW34070 Bragg Peak Chamber, sensitive volume diameter: 8.16 cm) was measured using high-resolution microCT. Signal dependence on angle α of beam incidence for square 6 MV fields of side length s = 20 cm and 1 cm was measured in air. Polarity and recombination effects were characterized in 6, 10, and 18 MV photons fields. To assess the lateral setup tolerance, scanned LAC profiles of a 1 × 1 cm 2 field were acquired. A 6 MV calibration coefficient, N D ,w, LAC , was determined in a field collimated by a 5 cm diameter stereotactic cone with known DAP w . Additional calibrations in 10 × 10 cm 2 fields at 6, 10, and 18 MV were performed. Electrode separation is uniform and agrees with specifications. Volume-averaging leads to a signal increase proportional to ~1/cos(α) in small fields. Correction factors for polarity and recombination range between 0.9986 to 0.9996 and 1.0007 to 1.0024, respectively. Off-axis displacement by up to 0.5 cm did not change the measured signal in a 1 × 1 cm 2 field. N D ,w, LAC was 163.7 mGy cm -2 nC -1 and differs by +3.0% from the coefficient derived in the 10 × 10 cm 2 6 MV field. Response in 10 and 18 MV fields increased by 1.0% and 2.7% compared to 6 MV. The LAC requires only small correction factors for DAP w measurements and shows little energy dependence. Lateral setup errors of 0.5 cm are tolerated in 1 × 1 cm 2 fields, but beam incidence must be kept as close to normal as possible. Calibration in 10 × 10 fields is not recommended because of the LAC's over-response. The accuracy of relative point-dose measurements in the field's periphery is an important limiting factor for the accuracy of DAP w measurements. © 2017 The Authors. Journal of Applied Clinical Medical Physics published by Wiley Periodicals, Inc. on behalf of American Association of Physicists in Medicine.

A neutron activation analysis procedure for the determination of uranium, thorium and potassium in geologic samples

USGS Publications Warehouse

Aruscavage, P. J.; Millard, H.T.

1972-01-01

A neutron activation analysis procedure was developed for the determination of uranium, thorium and potassium in basic and ultrabasic rocks. The three elements are determined in the same 0.5-g sample following a 30-min irradiation in a thermal neutron flux of 2??1012 n??cm-2??sec-1. Following radiochemical separation, the nuclides239U (T=23.5 m),233Th (T=22.2 m) and42K (T=12.36 h) are measured by ??-counting. A computer program is used to resolve the decay curves which are complex owing to contamination and the growth of daughter activities. The method was used to determine uranium, throium and potassium in the U. S. Geological Survey standard rocks DTS-1, PCC-1 and BCR-1. For 0.5-g samples the limits of detection for uranium, throium and potassium are 0.7, 1.0 and 10 ppb, respectively. ?? 1972 Akade??miai Kiado??.

Auger electron and characteristic energy loss spectra for electro-deposited americium-241

NASA Astrophysics Data System (ADS)

Varma, Matesh N.; Baum, John W.

1983-07-01

Auger electron energy spectra for electro-deposited americium-241 on platinum substrate were obtained using a cylindrical mirror analyzer. Characteristic energy loss spectra for this sample were also obtained at primary electron beam energies of 990 and 390 eV. From these measurements PI, PII, and PIII energy levels for americium-241 are determined. Auger electron energies are compared with theoretically calculated values. Minimum detectability under the present condition of sample preparation and equipment was estimated at approximately 1.2×10-8 g/cm2 or 3.9×10-8 Ci/cm2. Minimum detectability for plutonium-239 under similar conditions was estimated at about 7.2×10-10 Ci/cm2.

Electrodeposited Co-doped NiSe2 nanoparticles film: a good electrocatalyst for efficient water splitting

NASA Astrophysics Data System (ADS)

Liu, Tingting; Asiri, Abdullah M.; Sun, Xuping

2016-02-01

In this communication, we report that a Co-doped NiSe2 nanoparticles film electrodeposited on a conductive Ti plate (Co0.13Ni0.87Se2/Ti) behaves as a robust electrocatalyst for both HER and OER in strongly basic media, with good activity over a NiSe2/Ti counterpart. This Co0.13Ni0.87Se2/Ti catalytic electrode delivers 10 mA cm-2 at an overpotential of 64 mV for HER and 100 mA cm-2 at an overpotential of 320 mV for OER in 1.0 M KOH. A voltage of only 1.62 V is required to drive 10 mA cm-2 for the two-electrode alkaline water electrolyzer using Co0.13Ni0.87Se2/Ti as an anode and cathode.In this communication, we report that a Co-doped NiSe2 nanoparticles film electrodeposited on a conductive Ti plate (Co0.13Ni0.87Se2/Ti) behaves as a robust electrocatalyst for both HER and OER in strongly basic media, with good activity over a NiSe2/Ti counterpart. This Co0.13Ni0.87Se2/Ti catalytic electrode delivers 10 mA cm-2 at an overpotential of 64 mV for HER and 100 mA cm-2 at an overpotential of 320 mV for OER in 1.0 M KOH. A voltage of only 1.62 V is required to drive 10 mA cm-2 for the two-electrode alkaline water electrolyzer using Co0.13Ni0.87Se2/Ti as an anode and cathode. Electronic supplementary information (ESI) available: Experimental section and supplementary figures. See DOI: 10.1039/c5nr07170d

Spatial distribution of metals in soils in Baltimore, Maryland: role of native parent material, proximity to major roads, housing age and screening guidelines

Treesearch

I.D. Yesilonis; R.V. Pouyat; N.K. Neerchal

2008-01-01

We investigated the spatial distribution of heavy metal above-background (anthropic) contents of Cd, Co, Cu, Cr, Fe, Mn, Ni, Pb, Ti, V, and Zn in Baltimore City surface soils and related these levels to potential contaminating sources. Composite soil samples (0?10 cm depth) were digested using a nitric and hydrochloric extraction technique. Slightly more than 10% of...

Lifetime, collisional-quenching, and {ital j}-mixing measurements of the metastable 3{ital D} levels of Ca{sup +}

DOE Office of Scientific and Technical Information (OSTI.GOV)

Knoop, M.; Vedel, M.; Vedel, F.

1995-11-01

The metastable 3{sup 2}{ital D}{sub 3/2,5/2} doublet of Ca{sup +} ions stored in a Paul trap was investigated in the presence of different neutral gases, in the pressure range 10{sup {minus}9}--10{sup {minus}6} mbar. The natural lifetimes were determined to be {tau}({ital D}{sub 3/2})=1111{plus_minus}46 ms and {tau}({ital D}{sub 5/2})=994{plus_minus}38 ms, which agree very well with previous experiments. The estimation of the quenching rates of Ca{sup +}-He [{Gamma}{sub He}=(1.05{plus_minus}0.42){times}10{sup {minus}12} cm{sup 3} s{sup {minus}1}], Ca{sup +}-Ne [{Gamma}{sub Ne}=(0.9{plus_minus}0.7){times}10{sup {minus}12} cm{sup 3} s{sup {minus}1}], and Ca{sup +}-N{sub 2} [{Gamma}{sub N{sub 2}}=(1.7{plus_minus}0.2){times}10{sup {minus}10} cm{sup 3} s{sup {minus}1}] was carried out for collisions in themore » energy range 0.3--1.3 eV. In addition, rate constants for the mixing of the fine-structure states were measured in the presence of helium and nitrogen for the {ital j}=3/2{r_arrow}{ital j}=5/2 case [{gamma}{sub 35}(He)=(2.24{plus_minus}0.10){times}10{sup {minus}10} cm{sup 3} s{sup {minus}1} and {gamma}{sub 35}(N{sub 2})=(2.8{plus_minus}0.3){times}10{sup {minus}9} cm{sup 3} s{sup {minus}1}] and for the {ital j}=5/2{r_arrow}{ital j}=3/2 case [{gamma}{sub 53}(He)=(1.2{plus_minus}0.7){times}10{sup {minus}10} cm{sup 3} s{sup {minus}1} and {gamma}{sub 53}(N{sub 2})=(1.26{plus_minus}0.10){times}10{sup {minus}9} cm{sup 3} s{sup {minus}1}]. The measurements were carried out populating the metastable levels by direct laser excitation of the forbidden {ital S}-{ital D} transitions.« less

An observational study of the potential for human exposures to pet-borne diazinon residues following lawn applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Morgan, Marsha K.; Stout, Daniel M.; Jones, Paul A.

This study examined the potential for pet dogs to be an important pathway for transporting diazinon residues into homes and onto its occupants following residential lawn applications. The primary objectives were to investigate the potential exposures of occupants and their pet dogs to diazinon after an application to turf at their residences and to determine if personal contacts between occupants and their pet dogs resulted in measurable exposures. It was conducted from April to August 2001 before the Agency phased out all residential uses of diazinon in December 2004. Six families and their pet dogs were recruited into the study.more » Monitoring was conducted at pre-, 1, 2, 4, and 8 days post-application of a commercial, granular formulation of diazinon to the lawn by the homeowner. Environmental samples collected included soil, indoor air, carpet dust, and transferable residues from lawns and floors. Samples collected from the pet dogs consisted of paw wipes, fur clippings, and transferable residues from the fur by a technician or child wearing a cotton glove(s). First morning void (FMV) urine samples were collected from each child and his/her parent on each sampling day. Diazinon was analyzed in all samples, except urine, by GC-MS. The metabolite 2-isopropyl-4-methyl-6-hydroxypyrimidine (IMPy) was analyzed in the urine samples by HPLC-MS/MS. Mean airborne residues of diazinon on day 1 post-application were at least six times higher in both the living rooms (235{+-}267 ng/m{sup 3}) and children's bedrooms (179{+-}246 ng/m{sup 3}) than at pre-application. Mean loadings of diazinon in carpet dust samples were at least 20 times greater on days 2, 4, and 8 post-application than mean loadings (0.03{+-}0.04 ng/cm{sup 2}) at pre-application. The pet dogs had over 900 times higher mean loadings of diazinon residues on their paws on day 1 post-application (88.1{+-}100.1 ng/cm{sup 2}) compared to mean loadings (<0.09 ng/cm{sup 2}) at pre-application. The mean diazinon loadings on the fur clippings were at least 14 times higher on days 1, 2, 4, and 8 post-application than mean loadings (0.8{+-}0.4 ng/cm{sup 2}) at pre-application. For transferable residues from dog fur, the mean loadings of diazinon on the technician's cotton glove samples were the lowest before application (0.04{+-}0.08 ng/cm{sup 2}) and the highest on day 1 post-application (10.4{+-}23.9 ng/cm{sup 2}) of diazinon to turf. Urinary IMPy concentrations for the participants ranged from <0.3 to 5.5 ng/mL before application and <0.3-12.5 ng/mL after application of diazinon. The mean urinary IMPy concentrations for children or adults were not statistically different (p>0.05) at pre-application compared to post-application of diazinon to turf. The results showed that the participants and their pet dogs were likely exposed to low levels of diazinon residues from several sources (i.e., air, dust, and soil), through several pathways and routes, after lawn applications at these residences. Lastly, the pet dog appears to be an important pathway for the transfer and translocation of diazinon residues inside the homes and likely exposed occupants through personal contacts (i.e., petting)« less

Large sample area and size are needed for forest soil seed bank studies to ensure low discrepancy with standing vegetation.

PubMed

Shen, You-xin; Liu, Wei-li; Li, Yu-hui; Guan, Hui-lin

2014-01-01

A large number of small-sized samples invariably shows that woody species are absent from forest soil seed banks, leading to a large discrepancy with the seedling bank on the forest floor. We ask: 1) Does this conventional sampling strategy limit the detection of seeds of woody species? 2) Are large sample areas and sample sizes needed for higher recovery of seeds of woody species? We collected 100 samples that were 10 cm (length) × 10 cm (width) × 10 cm (depth), referred to as larger number of small-sized samples (LNSS) in a 1 ha forest plot, and placed them to germinate in a greenhouse, and collected 30 samples that were 1 m × 1 m × 10 cm, referred to as small number of large-sized samples (SNLS) and placed them (10 each) in a nearby secondary forest, shrub land and grass land. Only 15.7% of woody plant species of the forest stand were detected by the 100 LNSS, contrasting with 22.9%, 37.3% and 20.5% woody plant species being detected by SNLS in the secondary forest, shrub land and grassland, respectively. The increased number of species vs. sampled areas confirmed power-law relationships for forest stand, the LNSS and SNLS at all three recipient sites. Our results, although based on one forest, indicate that conventional LNSS did not yield a high percentage of detection for woody species, but SNLS strategy yielded a higher percentage of detection for woody species in the seed bank if samples were exposed to a better field germination environment. A 4 m2 minimum sample area derived from power equations is larger than the sampled area in most studies in the literature. Increased sample size also is needed to obtain an increased sample area if the number of samples is to remain relatively low.

Chernozems microbial community under anthropogenic impact (Russia)

NASA Astrophysics Data System (ADS)

Ivashchenko, Kristina; Ananyeva, Nadezhda; Sushko, Sofia; Vasenev, Viacheslav

2017-04-01

Chernozems is important natural resource, which in the last decade under intense influence as a result of plowing and urbanization. The parameters of soil microbial community functioning might be identify some soil deterioration under the impacts. Our research was focused on assessment of microbial community status in different soil layers of virgin steppe, bare fallow and urban ecosystems (Kursk region). In each ecosystem, we chose randomly 3-5 spatially distributed sites, where soil samples were collected by auguring up to 0.5 m depth (each layer 10 cm thickness) and up to 1.5 m depth (0-10, 10-50, 50-100, 100-150 cm layers), totally 127 samples. The bulk density was measured for these soil layers. In all soil samples the microbial biomass carbon content (Cmic) was analyzed by substrate-induced respiration (SIR) method and basal respiration (BR) was assessed by CO2 rate production. The fungi-to-bacteria ratio (selective inhibition technique with antibiotics) was determined and portion of Cmic in soil organic carbon (Corg) content was calculated in topsoil (0-10 cm). The Corg (dichromate oxidation) and pHw (potentiometry) values were measured. The Cmic and BR profile pools were calculated using bulk density and thickness of studied layers. The Cmic (0-10 cm) was varied from 84 to 1954 µg C g-1 soil, in steppe it was on average 3-4 times higher than those in bare fallow and urban. The BR rate was amounted from 0.20 to 1.57 µg CO2-C g-1 soil h-1, however no significant difference between studied ecosystems was found. It was shown the relationship between Cmic, BR and Corg (the linear regression, R2=0.92 and 0.75, respectively, p<0.05). The Cmic / Corg ratio in steppe was on average 3.3%, it was significantly higher those bare fallow and urban (1.6 and 0.7%, respectively). The fungi-to-bacteria ratio was decreased along ecosystems row: virgin steppe>bare fallow>urban, and it was on average 6.0, 5.2 and 1.8, respectively. The Cmic profile pool (0.5 m) of steppe was reached up on average 206 g C m-2, and it was 2.0 and 2.5 times higher those bare fallow and urban, respectively. The BR profile pool (0.5 m) in steppe and bare fallow was reached up 5.9 and 5.8 g CO2-C m-2 d-1, respectively, it was on average 2 times higher urban. The Cmic profile pool (1.5 m) in steppe was amounted to 372 g C m-2, and it was essentially higher those in bare fallow and urban (138 and 140 g C m-2, respectively). The BR profile pool (1.5 m) was also decreased along ecosystems row: steppe> fallow>urban, and it was on average 13.0, 8.0 and 5.6 g CO2-C m-2 d-1, respectively. Thus, we found a significant decreasing soil microbial biomass content, its portion in soil Corg, fungi content, and the Cmic and BR profile pools along Chernozems' ecosystems gradient from natural (virgin steppe) to anthropogenically transformed (bare fallow, urban). It might be illustrated some deterioration of soil microbial community functioning under plowing and urbanization. This research was supported by RFBR grants Nos. 15-04-00915 and 16-34-00398

Development, validation and testing of a skin sampling method for assessment of metal exposure.

PubMed

Erfani, Behnaz; Midander, Klara; Lidén, Carola; Julander, Anneli

2017-07-01

Nickel, cobalt and chromium are frequent skin sensitizers. Skin exposure results in eczema in sensitized individuals, the risk being related to the skin dose. To develop a self-sampling method for quantification of skin exposure to metals, to validate the method, and to assess its feasibility. Defined metal doses (0.01-5 µg) were applied to the fingers of 5 participants. Skin areas (2 cm 2 ) were sampled with 1% HNO 3 , either as 0.1 ml on a swab, or as 0.5 ml on a wipe. Furthermore, 17 participants performed self-sampling by swab after 2 h of leisure activity. Samples were extracted in 1% HNO 3 and analysed by inductively coupled plasma mass spectrometry. The sampling efficiency by swab was 46%, as compared with 93% for acid wipe sampling, for all tested doses. Most metal from the skin dose was detected in the first swab (33-43%). Despite lower sampling efficiency by swab, skin doses of metals following 2 h of leisure activity without hand washing were quantified in all participants, and ranged from 0.0016 to 0.15 µg/cm 2 , from 0.00014 to -0.0020 µg/cm 2 and from 0.00048 to -0.027 µg/cm 2 for nickel, cobalt, and chromium, respectively. The results indicate a future potential of skin sampling by swab to detect and monitor metals on skin by self-sampling. This will contribute to better knowledge of metal skin exposure among dermatitis patients, workers, and the general population. © 2017 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Effects of water level on three wetlands soil seed banks on the Tibetan Plateau.

PubMed

Ma, Miaojun; Ma, Zhen; Du, Guozhen

2014-01-01

Although the effect of water level on germination in soil seed banks has been documented in many ecosystems, the mechanism is not fully understood, and to date no empirical studies on this subject exist. Further, no work has been done on the effect of water level on seed banks of drying and saline-alkaline wetlands in alpine areas on the Tibetan Plateau. We examined the effects of water level (0 cm, 5 cm and 10 cm) on seed germination and seedling establishment from soil seed banks at 0-5 cm and 5-10 cm depths in typical, drying, and saline-alkaline wetlands. We also explore the potential role of soil seed bank in restoration of drying and saline-alkaline wetlands. Species richness decreased with increase in water level, but there almost no change in seed density. A huge difference exists in species composition of the seed bank among different water levels in all three wetlands, especially between 0 cm and 5 cm and 0 cm and 10 cm. Similarity of species composition between seed bank and plant community was higher in 0 cm water level in drying wetland than in the other two wetlands. The similarity was much higher in 0 cm water level than in 5 cm and 10 cm water levels in all three wetlands. Species composition of the alpine wetland plant community changed significantly after drying and salinization, however, species composition of the seed bank was unchanged regardless of the environment change. Water level greatly affects seed bank recruitment and plant community establishment. Further, different water levels in restored habitats are likely to determine its species composition of the plant community. The seed bank is important in restoration of degraded wetlands. Successful restoration of drying and salinization wetlands could depend on the seed bank.

Placental morphometry and Doppler flow velocimetry in cases of chronic human fetal hypoxia.

PubMed

Kuzmina, Irina Y; Hubina-Vakulik, Galina I; Burton, Graham J

2005-06-01

To investigate the structural basis of abnormal Doppler waveforms in the utero-placental circulations in cases of chronic fetal hypoxia. Morphometric analysis was performed on placental samples from 58 pregnancies with abnormal Doppler waveforms in the uterine, placental and umbilical circulations at 32-34 weeks, and 10 pregnancies with normal waveforms. The volume of placental villi reduced from 350.5 cm3 in controls to 286.4 cm3 (P<0.05) in the severest cases. The volume of the fetal capillaries reduced from 59.7 cm3 to 20.5 cm3 (P<0.05). These reductions were associated with increased placental infarction. The myometrial segments of the spiral arteries were severely constricted, demonstrating failure of physiological conversion secondary to deficient trophoblast invasion. The placental vascular bed is greatly reduced in cases of chronic fetal hypoxia. We propose impaired placental perfusion causes oxidative stress and regression of the fetal vasculature, leading to fetal growth retardation and distress.

Assimilation of SMOS Retrievals in the Land Information System

PubMed Central

Blankenship, Clay B.; Case, Jonathan L.; Zavodsky, Bradley T.; Crosson, William L.

2018-01-01

The Soil Moisture and Ocean Salinity (SMOS) satellite provides retrievals of soil moisture in the upper 5 cm with a 30-50 km resolution and a mission accuracy requirement of 0.04 cm3 cm−3. These observations can be used to improve land surface model soil moisture states through data assimilation. In this paper, SMOS soil moisture retrievals are assimilated into the Noah land surface model via an Ensemble Kalman Filter within the NASA Land Information System. Bias correction is implemented using Cumulative Distribution Function (CDF) matching, with points aggregated by either land cover or soil type to reduce sampling error in generating the CDFs. An experiment was run for the warm season of 2011 to test SMOS data assimilation and to compare assimilation methods. Verification of soil moisture analyses in the 0-10 cm upper layer and root zone (0-1 m) was conducted using in situ measurements from several observing networks in the central and southeastern United States. This experiment showed that SMOS data assimilation significantly increased the anomaly correlation of Noah soil moisture with station measurements from 0.45 to 0.57 in the 0-10 cm layer. Time series at specific stations demonstrate the ability of SMOS DA to increase the dynamic range of soil moisture in a manner consistent with station measurements. Among the bias correction methods, the correction based on soil type performed best at bias reduction but also reduced correlations. The vegetation-based correction did not produce any significant differences compared to using a simple uniform correction curve. PMID:29367795

CXCL4 and CXCL10 Predict Risk of Fatal Cerebral Malaria

PubMed Central

Wilson, Nana O.; Jain, Vidhan; Roberts, Christina E.; Lucchi, Naomi; Joel, Pradeep K.; Singh, Mrigendra P.; Nagpal, Avinash C.; Dash, Aditya P.; Udhayakumar, Venkatachalam; Singh, Neeru; Stiles, Jonathan K.

2011-01-01

Plasmodium falciparum in a subset of patients can lead to a diffuse encephalopathy known as cerebral malaria (CM). Despite treatment, mortality caused by CM can be as high as 30% while 10% of survivors of the disease may experience short- and long-term neurological complications. The pathogenesis of CM involves alterations in cytokine and chemokine expression, local inflammation, vascular injury and repair processes. These diverse factors have limited the rate of discovery of prognostic predictors of fatal CM. Identification of reliable early predictors of CM severity will enable clinicians to adjust this risk with appropriate management of CM. Recent studies revealed that elevated levels of CXCL10 expression in cerebrospinal fluid and peripheral blood plasma independently predicted severe and fatal CM. CXCR3, a promiscuous receptor of CXCL10, plays an important role in pathogenesis of mouse model of CM. In this study the role of corresponding CXCR3 ligands (CXCL11, CXCL10, CXCL9 & CXCL4) in fatal or severe CM was evaluated by comparing their levels in 16 healthy control (HC), 26 mild malaria (MM), 26 cerebral malaria survivors (CMS) and 12 non-survivors (CMNS) using enzyme linked immunosorbent assay (ELISA). Levels of CXCL4 and CXCL10 were significantly elevated in CMNS patients (p < 0.05) when compared with HC, MM and CMS. Elevated plasma levels of CXCL10 and CXCL4 were tightly associated with CM mortality. Receiver Operating Characteristic (ROC) curve analysis revealed that CXCL4 and CXCL10 can discriminate CMNS from MM (p < 0.0001) and CMS (p < 0.0001) with an area under the curve (AUC) = 1. These results suggest that CXCL4 and CXCL10 play a prominent role in pathogenesis of CM associated death and may be used as functional or surrogate biomarkers for predicting CM severity. PMID:21508508

CXCL4 and CXCL10 predict risk of fatal cerebral malaria.

PubMed

Wilson, Nana O; Jain, Vidhan; Roberts, Christina E; Lucchi, Naomi; Joel, Pradeep K; Singh, Mrigendra P; Nagpal, Avinash C; Dash, Aditya P; Udhayakumar, Venkatachalam; Singh, Neeru; Stiles, Jonathan K

2011-01-01

Plasmodium falciparum in a subset of patients can lead to a diffuse encephalopathy known as cerebral malaria (CM). Despite treatment, mortality caused by CM can be as high as 30% while 10% of survivors of the disease may experience short- and long-term neurological complications. The pathogenesis of CM involves alterations in cytokine and chemokine expression, local inflammation, vascular injury and repair processes. These diverse factors have limited the rate of discovery of prognostic predictors of fatal CM. Identification of reliable early predictors of CM severity will enable clinicians to adjust this risk with appropriate management of CM. Recent studies revealed that elevated levels of CXCL10 expression in cerebrospinal fluid and peripheral blood plasma independently predicted severe and fatal CM. CXCR3, a promiscuous receptor of CXCL10, plays an important role in pathogenesis of mouse model of CM. In this study the role of corresponding CXCR3 ligands (CXCL11, CXCL10, CXCL9 & CXCL4) in fatal or severe CM was evaluated by comparing their levels in 16 healthy control (HC), 26 mild malaria (MM), 26 cerebral malaria survivors (CMS) and 12 non-survivors (CMNS) using enzyme linked immunosorbent assay (ELISA). Levels of CXCL4 and CXCL10 were significantly elevated in CMNS patients (p < 0.05) when compared with HC, MM and CMS. Elevated plasma levels of CXCL10 and CXCL4 were tightly associated with CM mortality. Receiver Operating Characteristic (ROC) curve analysis revealed that CXCL4 and CXCL10 can discriminate CMNS from MM (p < 0.0001) and CMS (p <0.0001) with an area under the curve (AUC)=1. These results suggest that CXCL4 and CXCL10 play a prominent role in pathogenesis of CM associated death and may be used as functional or surrogate biomarkers for predicting CM severity.

Analysis of the effect of spatial and temporal sampling densities on accuracy of predicting the heating profile in windrowed broiler litter

USDA-ARS?s Scientific Manuscript database

A standard method for monitoring temperature in windrow piles of broiler litter to predict microbial population reductions is described. Temperature data collected every 2 min on a 10 cm x 10 cm spatial sampling grid in five identically-constructed litter windrow piles was utilized in this study. ...

TEM characterization of irradiated U-7Mo/Mg dispersion fuel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gan, J.; Keiser, D. D.; Miller, B. D.

This paper presents the results of transmission electron microscopy (TEM) characterization on neutron-irradiated samples taken from the low-flux and high-flux sides of the same fuel plate with U-7Mo fuel particles dispersed in Mg matrix with aluminum alloy Al6061 as cladding material that was irradiated edge-on to the core in the Advanced Test Reactor. The corresponding local fission density and fission rate of the fuel particles and the average fuel-plate centerline temperature for the low-flux and high-flux samples are estimated to be 3.7 × 10 21 f/cm 3, 7.4 × 10 14 f/cm 3/s and 123 °C, and 5.5 × 10more » 21 f/cm3, 11.0 × 10 14 f/cm 3/s and 158 °C, respectively. Complex interaction layers developed at the Al-Mg interface, consisting of Al 3Mg 2 and Al 12Mg 17 along with precipitates of MgO, Mg 2Si and FeAl 5.3. No interaction between Mg matrix and U-Mo fuel particle was identified. For the U-Mo fuel particles, at low fission density, small elongated bubbles wrapped around the clean areas with a fission gas bubble superlattice, which suggests that bubble coalescence is an important mechanism for converting the fission gas bubble superlattice to large bubbles. At high fission density, no bubbles or porosity were observed in the Mg matrix, and pockets of residual fission gas bubble superlattice were observed in the U-Mo fuel particle interior.« less

TEM characterization of irradiated U-7Mo/Mg dispersion fuel

DOE PAGES

Gan, J.; Keiser, D. D.; Miller, B. D.; ...

2017-07-15

This paper presents the results of transmission electron microscopy (TEM) characterization on neutron-irradiated samples taken from the low-flux and high-flux sides of the same fuel plate with U-7Mo fuel particles dispersed in Mg matrix with aluminum alloy Al6061 as cladding material that was irradiated edge-on to the core in the Advanced Test Reactor. The corresponding local fission density and fission rate of the fuel particles and the average fuel-plate centerline temperature for the low-flux and high-flux samples are estimated to be 3.7 × 10 21 f/cm 3, 7.4 × 10 14 f/cm 3/s and 123 °C, and 5.5 × 10more » 21 f/cm3, 11.0 × 10 14 f/cm 3/s and 158 °C, respectively. Complex interaction layers developed at the Al-Mg interface, consisting of Al 3Mg 2 and Al 12Mg 17 along with precipitates of MgO, Mg 2Si and FeAl 5.3. No interaction between Mg matrix and U-Mo fuel particle was identified. For the U-Mo fuel particles, at low fission density, small elongated bubbles wrapped around the clean areas with a fission gas bubble superlattice, which suggests that bubble coalescence is an important mechanism for converting the fission gas bubble superlattice to large bubbles. At high fission density, no bubbles or porosity were observed in the Mg matrix, and pockets of residual fission gas bubble superlattice were observed in the U-Mo fuel particle interior.« less

Effect of 0.12% chlorhexidine in reducing microorganisms found in aerosol used for dental prophylaxis of patients submitted to fixed orthodontic treatment

PubMed Central

dos Santos, Isis Rodrigues Menezes; Moreira, Ana Cristina Azevedo; Costa, Myrela Galvão Cardoso; Barbosa, Marcelo de Castellucci e

2014-01-01

Objective This study aimed at assessing, in vivo, whether the prior use of 0.12% chlorhexidine as mouthwash would decrease air contamination caused by aerosolized sodium bicarbonate during dental prophylaxis. The study was conducted with 23 patients aged between 10 and 40 years old who were randomly selected and undergoing fixed orthodontic treatment. Methods The study was divided into two phases (T1 and T2) with a 30-day interval in between. In both phases, dental prophylaxis was performed with aerosolized sodium bicarbonate jetted to the upper and lower arches for 4 minutes. In T1, 10 minutes before the prophylaxis procedure, the participants used distilled water as mouthwash for one minute; whereas in T2, mouthwash was performed with 0.12% chlorhexidine. Microbial samples were collected in BHI agar plates for microbiological analysis. Two dishes were positioned on the clinician (10 cm from the mouth) and a third one at 15 cm from the patient's mouth. The samples were incubated for 48 hours at 37°C. Results were expressed in colony-forming units (CFU). Results Statistical analysis carried out by means of Student's t test, as well as Wilconxon and Kruskal-Wallis tests revealed that the prior use of 0.12% chlorhexidine as mouthwash significantly reduced CFU in the three positions studied (P < 0.001). Conclusion The prior use of 0.12% chlorhexidine as mouthwash significantly reduced contamination caused by aerosolized sodium bicarbonate during dental prophylaxis in the orthodontic clinic. PMID:25162572

Magma Mixing: Magmatic Enclaves in Morne Micotrin, Dominica

NASA Astrophysics Data System (ADS)

Hickernell, S.; Frey, H. M.; Manon, M. R. F.; Waters, L. E.

2017-12-01

Magmatic enclaves in volcanic rocks provide direct evidence of magma mingling/mixing within a magma reservoir and may reinvigorate the system and trigger eruption, as documented at the Soufriere Hills in Montserrat. Lava domes on the neighboring island of Dominica also contain multiple enclave populations and may be evidence for similar magma chamber processes. The central dome of Micotrin is at the head of the Roseau Valley, which was filled with 3 km3 of pyroclastic deposits from eruptions spanning 65 - 25 ka. There appear to be two distinct types of enclaves in the crystal-rich Micotrin andesites (60 wt% SiO2), fine-grained and coarse-grained. Fine-grained mafic enclaves (52 wt% SiO2) vary in size from 1 to 15 cm in diameter, whereas the coarse-grained enclaves are generally larger and range from 3-20 cm. Fine-grained enclaves are saturated in plag (35%) + opx (35%) + cpx (20%) + oxides (10%). Average pyroxenes are 0.01 to 0.02 cm in size, whereas plagioclase averages 0.05 cm and up to 0.1 cm. The texture of the fine-grained enclaves is cumulate-like, devoid of microlites and matrix glass. Coarse-grained enclaves lack cpx and have different modal abundances and textures: plag (75%) + opx (10%) + oxides (5%) + plag microlites (10%). Plagioclase are 0.1 cm in size and orthopyroxenes average 0.05 cm. The coarse-grained enclaves are highly vesicular, a notable difference from the host as well as the fine-grained enclaves. The boundaries of both the fine- and coarse-grained enclaves are quite sharp and distinct and there do not appear to be enclave minerals disaggregated in the host rock. Temperatures were determined by two oxides. The fine-grained enclaves had two populations of magnetite, yielding 847 + 21° and 920 + 17°C. The coarse-grained enclave was 890 + 42 °C, but the oxides were extensively exsolved. Plagioclase composition in both coarse and fine-grained samples was comparable, ranging from An50 to An80. Despite compositional similarity the textures of the plagioclase are distinctive. Fine-grained enclave plagioclase has patchy, uneven zoning, whereas coarse-grained enclave plagioclase has oscillatory zoning. The presence of these enclaves indicates that there may be several different magma inputs contributing to the system that is feeding Micotrin, and the injection of these unique magmas may be eruption triggers.

Epidural analgesia in early labour blocks the stress response but uterine contractions remain unchanged.

PubMed

Scull, T J; Hemmings, G T; Carli, F; Weeks, S K; Mazza, L; Zingg, H H

1998-07-01

To determine the effect of epidural analgesia on biochemical markers of stress, plasma oxytocin concentrations and frequency of uterine contractions during the first stage of labour. Nine nulliparous women, in spontaneous labour, with a singleton fetus and cervical dilatation < or = 5 cm were enrolled. Epidural bupivacaine 0.25% (range 10-14 ml) was administered and bilateral sensory blockade to ice (T8-L4) achieved. Blood samples were collected before the epidermal block and every 10 min for one hour after the block was achieved for the measurement of plasma beta-endorphin, cortical, glucose, lactate and oxytocin concentrations. No exogenous oxytocin was given. Intensity of pain was assessed at the time of the blood sampling using a 10 cm visual analogue scale (VAS). The frequency of uterine contractions was recorded for 60 min before and after the epidural block. There was a decrease in plasma beta-endorphin and cortisol concentrations after epidural block (P < 0.01). There were no changes in plasma glucose and lactate concentrations. The mean VAS for pain decreased 10 min after epidural block was achieved and remained < 2 throughout the study period (P < 0.001). Mean plasma oxytocin concentrations did not change. The frequency of uterine contractions before and after the epidural block was similar. The metabolic stress response to the pain of labour was attenuated by epidural analgesia. In contrast, plasma oxytocin concentration and frequency of uterine contractions were unaffected by the attenuation of metabolic stress response.

Mapping snow depth within a tundra ecosystem using multiscale observations and Bayesian methods

DOE PAGES

Wainwright, Haruko M.; Liljedahl, Anna K.; Dafflon, Baptiste; ...

2017-04-03

This paper compares and integrates different strategies to characterize the variability of end-of-winter snow depth and its relationship to topography in ice-wedge polygon tundra of Arctic Alaska. Snow depth was measured using in situ snow depth probes and estimated using ground-penetrating radar (GPR) surveys and the photogrammetric detection and ranging (phodar) technique with an unmanned aerial system (UAS). We found that GPR data provided high-precision estimates of snow depth (RMSE=2.9cm), with a spatial sampling of 10cm along transects. Phodar-based approaches provided snow depth estimates in a less laborious manner compared to GPR and probing, while yielding a high precision (RMSE=6.0cm) andmore » a fine spatial sampling (4cm×4cm). We then investigated the spatial variability of snow depth and its correlation to micro- and macrotopography using the snow-free lidar digital elevation map (DEM) and the wavelet approach. We found that the end-of-winter snow depth was highly variable over short (several meter) distances, and the variability was correlated with microtopography. Microtopographic lows (i.e., troughs and centers of low-centered polygons) were filled in with snow, which resulted in a smooth and even snow surface following macrotopography. We developed and implemented a Bayesian approach to integrate the snow-free lidar DEM and multiscale measurements (probe and GPR) as well as the topographic correlation for estimating snow depth over the landscape. Our approach led to high-precision estimates of snow depth (RMSE=6.0cm), at 0.5m resolution and over the lidar domain (750m×700m).« less

Evaluation of lattice displacement in Mg - Implanted GaN by Rutherford backscattering spectroscopy

NASA Astrophysics Data System (ADS)

Nishikata, N.; Kushida, K.; Nishimura, T.; Mishima, T.; Kuriyama, K.; Nakamura, T.

2017-10-01

Evaluation of lattice displacement in Mg-ion implanted GaN is studied by combining elastic recoil detection analysis (ERDA), Rutherford backscattering spectroscopy (RBS) and Photoluminescence (PL) measurements. Mg-ion implantation into GaN single crystal wafer is performed with energies of 30 keV (ion fluence; 3.5 × 1014 cm-2) and 60 keV (6.5 × 1014 cm-2) at room temperature. The ERDA measurements using the 1.5 MeV helium beam can evaluate hydrogen from the surface to ∼300 nm. The hydrogen concentration for un-implanted and as-implanted GaN is 3.1 × 1014 cm-2 and 6.1 × 1014 cm-2 at around 265 nm in depth. χmin (the ratio of aligned and random yields) near the surface of the 〈0 0 0 1〉 direction for Ga is 1.61% for un-implanted and 2.51% for Mg-ion implanted samples. On the other hand, the value of χmin for N is 10.08% for un-implanted and 11.20% for Mg-ion implanted samples. The displacement concentration of Ga and N estimated from these χmin values is 4.01 × 1020 cm-3 and 5.46 × 1020 cm-3, respectively. This suggests that Ga vacancy (VGa), N vacancy (VN), Ga interstitial (Gai), and N interstitial (Ni) is introduced in Mg-ion implanted GaN. A strong emission at around 400 nm in as-implanted GaN is related to a VN donor and some acceptor pairs. It is suggested that the origin of the very high resistivity after the Mg-ion implantation is attributed to the carrier compensation effect due to the deep level of Ni as a non-radiative center.

Mapping snow depth within a tundra ecosystem using multiscale observations and Bayesian methods

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wainwright, Haruko M.; Liljedahl, Anna K.; Dafflon, Baptiste

This paper compares and integrates different strategies to characterize the variability of end-of-winter snow depth and its relationship to topography in ice-wedge polygon tundra of Arctic Alaska. Snow depth was measured using in situ snow depth probes and estimated using ground-penetrating radar (GPR) surveys and the photogrammetric detection and ranging (phodar) technique with an unmanned aerial system (UAS). We found that GPR data provided high-precision estimates of snow depth (RMSE=2.9cm), with a spatial sampling of 10cm along transects. Phodar-based approaches provided snow depth estimates in a less laborious manner compared to GPR and probing, while yielding a high precision (RMSE=6.0cm) andmore » a fine spatial sampling (4cm×4cm). We then investigated the spatial variability of snow depth and its correlation to micro- and macrotopography using the snow-free lidar digital elevation map (DEM) and the wavelet approach. We found that the end-of-winter snow depth was highly variable over short (several meter) distances, and the variability was correlated with microtopography. Microtopographic lows (i.e., troughs and centers of low-centered polygons) were filled in with snow, which resulted in a smooth and even snow surface following macrotopography. We developed and implemented a Bayesian approach to integrate the snow-free lidar DEM and multiscale measurements (probe and GPR) as well as the topographic correlation for estimating snow depth over the landscape. Our approach led to high-precision estimates of snow depth (RMSE=6.0cm), at 0.5m resolution and over the lidar domain (750m×700m).« less

Changes of soil organic matter and microbial activity in irrigated and non irrigated olive groves

NASA Astrophysics Data System (ADS)

Kavvadias, Victor; Papadopoulou, Maria; Theocharopoulos, Sideris; Vavoulidou, Evagelia; Doula, Maria; Reppas, Spiros

2014-05-01

The implementation of olive cultivation techniques in Greece has not been systematically tested under the prevailing Mediterranean conditions. A LIFE+ project was initiated (oLIVE-CLIMA; LIFE 11/ENV/000942) aiming to introduce new management practices in olive tree crops that lead to increased carbon dioxide uptake by plants as well as carbon sequestration from the atmosphere and reverse the trend of soil organic matter decline, erosion and desertification. This paper presents data on soil organic matter and microbial activity from a soil campaign in a pilot region in Greece, and particularly in the area of Chora, prefecture of Messinia, South west Peloponnese. The soil campaign took place during the period December 2012-February 2013. Twelve soil parcels of olive groves were selected (6 irrigated and 6 rainfed) and in each soil parcel six composite soil samples were taken from 0-10 cm depth at equal intervals along a straight line of the trunk of the tree to the middle of the distance from the nearest tree of the next tree series. The first three samples were under olive tree canopy. An additional composite sample was taken at depth of 10-40 cm. Soil samples were analyzed for soil physicochemical and biological properties. In this study results for total organic carbon (TOC), soil basal microbial respiration (BR), microbial biomass C (MB-C) from the region of Messinia, are presented. Organic matter was determined by dichromate oxidation. The microbial activity was measured by the amount of CO2 evolution, while microbial biomass C was determined by substrate-induced respiration, after the addition of glucose. The results showed considerable differences in TOC, BR and MB-C associated with the sampling position and soil depth. The higher TOC, BR and MB-C values, in most cases, were determined in samples taken from points under the canopy, but not close to the tree trunk compared to the sampling points outside the canopy. This indicates the positive effect of rhizosphere and the favorable soil moisture conditions under tree canopy on soil microbial activities. TOC, BR and MB-C values were considerably lower in soil depth of 10-40cm compared with 0-10 cm in both irrigated and rainfed soil parcels. Moreover BR and MB-C was higher in irrigated soil parcels compared with rainfed ones suggesting that the periodic irrigation significantly enhances the soil microbial activity. There were no considerable differences in TOC. For this the TOC and potential activity of microbial community can contribute in the soil nutrient and irrigation management guidelines in order to exploit the utilization of productive soils in the region under studied.

Nitrogen availability from residues-based biochar at two pyrolisis temperatures

NASA Astrophysics Data System (ADS)

Coscione, Aline Renee; Silveira Bibar, Maria Paula; de Andrade, Cristiano Alberto

2014-05-01

Biochar has been studied for several applications, such as soil quality improvement, heavy metals remediation and N2O mitigation. Considering the soil quality improvement aspect it is desirable to evaluate if the nitrogen content in biochar samples obtained from several residues used as the biomass sources could be available for plants. Samples of sewage sludge (SS), coffee grounds (CG), chicken manure (CM) and fungi mycelia (FM) were pyrolyzed at two temperatures, 400 and 700 oC (indicated by the number 4 and 7 in this abstract, respectively), in order to obtain the biochar samples. The Kjeldahl nitrogen of biochar was (% m/m): 3.0 (CM4, CG7, FM7 and CG4); 2.0 (CM7 e SS4); 3.4 (FM7); 1.4 (SS7), with organic carbon (potassium dichromate method) ranging from 2.0 to 3.0% for all but CG4 (6%). The C/N ratio of biochar samples was: 9 (CM4, SS4 and CG7); 11 (CM7); 15 (SS7); 7 (FM4 and FM7); 21 (CG4). The eight soil + biochar resulting mixtures, prepared using the equivalent to 60 t/ha of biochar (about 3% w/w), and one additional control treatment (no biochar added) were incubated for 90 days, with four replications of each treatment per time evaluated. Inorganic nitrogen and soil pH measurements were performed for all treatments at 0, 5, 15, 30, 60 and 90 days of incubation. Soil moisture was kept at 40% soil water holding capacity, by weighting, during the experiment. The data was submitted to ANOVA with Tukey's average comparison test (p < 0.05). No significative pH changes were observed during the incubation of biochar samples. At the initial incubation time (zero days) no statistical difference was observed among biochar sources or pyrolisis temperatures. After five days of incubation SS4 and CM4 showed significant inorganic nitrogen release compared to all other treatments, behavior repeated at all the following times evaluated. For CM7, FM4 and FM7 maximum nitrogen availability was observed after 15 days, while it occurred after 90 days for SS4. After 90 days, only SS4 and CM4 presented a positive nitrogen balance, reaching 8 and 9 % of the nitrogen added by biochar samples release to the soil, respectively. A first order kinetic model was adjusted for SS4 nitrogen release, enabling the calculation of half life (10 days), potential available nitrogen (76.5 mg/kg) and the speed of the process. However, compared to SS4 the standard nitrogen availability of sewage sludge is up to 30% of its Kjeldahl nitrogen. For organic residues with C/N ratios lower than 20 applied to the soil a fast degradation, with the corresponding increase in inorganic nitrogen availability is expect. Although all the biochar samples tested had C/N ratios below that cutting point, just 2 of 8 presented inorganic nitrogen available in the soil+biochar mixtures. These results show that soil incubation tests are ultimate for the evaluation of the nitrogen potential release to the soil. Low temperature SS based biochar may offer additional nitrogen release to soil besides other soil conditioning properties.

Dendrogeochronologic and Anatomic Analysis of Excavated Plains Cottonwoods Determine Overbank Sedimentation Rates and Historical Channel Positions Along the Interior of a Migrating Meander Bend, Powder River, Montana

NASA Astrophysics Data System (ADS)

Metzger, T. L.; Pizzuto, J. E.; Schook, D. M.; Hasse, T. R.; Affinito, R. A.

2017-12-01

Dendrochronological dating of buried trees precisely determines the germination year and identifies the stratigraphic context of germination for the trees. This recently developed application of dendrochronology provides accurate time-averaged sedimentation rates of overbank deposition along floodplains and can be used to identify burial events. Previous studies have demonstrated that tamarisk (Tamarix ramosissima) and sandbar willow (Salix exigua) develop anatomical changes within the tree rings (increased vessel size and decreased ring widths) on burial, but observations of plains cottonwood (Populus deltoides ssp. monilifera) are lacking. In September 2016 and June 2017, five buried plains cottonwoods were excavated along a single transect of the interior of a meander bend of the Powder River, Montana. Sediment samples were obtained near each tree for 210Pb and 137Cs dating, which will allow for comparison between dendrochronological and isotopic dating methods. The plains cottonwood samples collected exhibit anatomical changes associated with burial events that are observed in other species. All trees germinated at the boundary between thinly bedded fine sand and mud and coarse sand underlain by sand and gravel, indicating plains cottonwoods germinate on top of point bars prior to overbank deposition. The precise germination age and depth provide elevations and minimum age constraints for the point bar deposits and maximum ages for the overlying sediment, helping constrain past channel positions and overbank deposition rates. Germination years of the excavated trees, estimated from cores taken 1.5 m above ground level, range from 2014 to 1862. Accurate establishment years determined by cross-dating the buried section of the tree can add an additional 10 years to the cored age. The sedimentation rate and accumulation thickness varied with tree age. The germination year, total sediment accumulation, and average sedimentation rate at the five sampled trees is: 2011, 35 cm, 7.0 cm/year; 1973, 77 cm, 1.8 cm/year; 1962, 140 cm, 2.6 cm/year; 1960, 123 cm, 2.2 cm/year; and 1862, 112 cm, 0.7 cm/year. These sedimentation rates indicate that the cumulative sedimentation decreases as a power law with increasing tree age.

Development of an reliable analytical method for synergistic extractive spectrophotometric determination of cobalt(II) from alloys and nano composite samples by using chromogenic chelating ligand

NASA Astrophysics Data System (ADS)

Kamble, Ganesh S.; Ghare, Anita A.; Kolekar, Sanjay S.; Han, Sung H.; Anuse, Mansing A.

2011-12-01

A synergistic simple and selective spectrophotometric method was developed for the determination of cobalt(II) with 1-(2',4'-dinitro aminophenyl)-4,4,6-trimethyl-1,4-dihydropyrimidine-2-thiol [2',4'-dinitro APTPT] as a chromogenic reagent. The proposed method has been described on the basis of synergistic effective extraction of cobalt(II) in presence of pyridine at pH range 9.5-10.2, showed orange-red coloured ternary complex having molar ratio 1:2:2 (M:L:Py). The equilibrium time is 10 min for extraction of cobalt(III) from organic phase. The absorbance of coloured organic layer in chloroform is measured spectrophotometrically at 490 nm against reagent blank. The Beer's law was obeyed in the concentration range 2.5-15 μg mL -1 of cobalt(II) and optimum concentration range was 5-12.5 μg mL -1 of cobalt(II) and it was evaluated from Ringbom's plot. The molar absorptivity and Sandell's sensitivity of cobalt(II)-2',4'-dinitro APTPT-pyridine complex in chloroform are 1.109 × 10 3 L mol -1 cm -1 and 0.053 μg cm -2, respectively while molar absorptivity and Sandell's sensitivity of cobalt(II)-2',4'-dinitro APTPT complex in chloroform are 6.22 × 10 2 L mol -1 cm -1 and 0.096 μg cm -2, respectively. The composition of cobalt(II)-2',4'-dinitro APTPT-pyridine complex (1:2:2) was established by slope ratio method, mole ratio method and Job's method of continuous variation. The ternary complex was stable for more than 48 h. The interfering effects of various cations and anions were also studied, and use of suitable masking agents enhances the selectivity of the method. The method is successfully applied for the determination of cobalt(II) in binary, synthetic mixtures and real samples. A repetition of the method was checked by finding relative standard deviation (R.S.D.) for n = 5 which was 0.15%. The reliability of the method is confirmed by comparison of experimental results with atomic absorption spectrophotometer.

Evaluation of abyssal meiobenthos in the eastern central Pacific (Clarion-Clipperton fracture zone)

NASA Astrophysics Data System (ADS)

Renaud-Mornant, Jeanne; Gourbault, Nicole

Meiobenthos were sampled from 17 stations in the abyssal deep-sea system of the central Pacific centered around 14°N, 130°W at depths 4960-5154m, during the Nixo 47 R/V Jean Charcot cruise. Meiofaunal density range from 45-89 ind. 10cm 2. Predominant taxa are nematodes (84-100%) and copepods (0-10%). Rotifera, Polychaeta, and Acarina also occur. Nematodes are uniformly distributed spatially with 45 species or so; Monhysteridae is the dominant taxon, and Syringolaimus sp. (Ironidae) co-occurs faithfully. Low biomass (0.4-70.6μg 10cm 2) are attributed to supposed dwarfism of metazoan meiofauna and very high proportion (60-80%) of juveniles and pre-adult forms. The majority of protozoans and metazoans are detritus- or deposit-feeders; in addition symbiotic associations, coprophagy and gardening activities are frequent. In such an oligotrophic environment, low food supply may limit meiofaunal abundance, biomass and maturation, and to a lesser extent species richness.

The relationship between gestational age and compliance in human umbilical vein and its possible application in vascular grafting.

PubMed

Li, Wenchun; Huang, Tiezhu; Zeng, Yanjun; Yao, Zhongjun

2006-03-01

The aim of this study was to provide a theoretical basis, using biomechanical properties, for the clinical application of human umbilical vein (HUV) as material for vascular grafting. This was a nonrandomized, non-controlled in vitro study. The experiment was conducted in the Laboratory of Medical Biomechanics, Yunyang Medical College. HUVs of 50 normal fetuses were collected on spontaneous miscarriage or labor with the pregnant women's permission by the Department of Obstetrics and Gynecology, Taihe Hospital, Shiyan, Hubei Province. Gestational aged ranged 24-42 weeks, and parturients were 20-30 years old. The pressure-volume (P-V) relationship of HUV was measured on the biomechanical experiment stand for soft tissues, and then compliance was calculated. The P-V relationship of HUV corresponded to a parabolic curve. The compliance of HUV increased gradually with gestational age [24-27 weeks (2.22+/-0.34) x 10(-4) mL/(kPa * cm), 28-32 weeks (3.65+/-0.46) x 10(-4) mL/(kPa * cm), 33-36 weeks (4.22+/-0.55) x 10(-4) mL/(kPa * cm), 37 weeks (7.63+/-0.48) x 10(-4) mL/(kPa * cm), 38 weeks (8.32+/-0.76) x 10(-4) mL/(kPa * cm)]. However, after 39 weeks of gestation, compliance decreased gradually with gestational age [39 weeks 7.61+/-0.46) x 10(-4) mL/(kPa * cm), 40 weeks (7.53+/-0.72) x 10(-4) mL/(kPa * cm), 41 weeks (4.13+/-0.35) x 10(-4) mL/(kPa * cm), 42 weeks (2.25+/-0.62) x 10(-4) mL/(kPa * cm)]. The compliance of HUVs collected at 37-40 weeks of gestational age was similar. When the HUVs older than 42 weeks or under 28 weeks were compared, there was significant difference in their compliance (F=65.84-86.52, p<0.01). The results of the present study suggest that HUVs collected at 37-40 weeks of gestational age have good compliance, i.e., a good P-V relationship, and therefore may be a suitable material for vascular grafting. HUV is one of several graft materials that may be used when autogenous saphenous vein is absent or inadequate. HUV is very biocompatible and shows promise for use in orthopedic implants.

Assessment of the usage of biodegradable polymeric matrix in vaginal devices to sustain progesterone release in cows.

PubMed

Pimentel, José Rodrigo Valim; Maturana Filho, Milton; Cardozo-Filho, Lucio; Agnelli, José Augusto M; Nascimento, Jefter; Madureira, Ed Hoffmann

2017-10-01

The usage of timed artificial insemination (TAI) at a low cost leading to better reproductive rates has been the aim of several research groups in the field. Usually during TAI protocols, sustained progesterone (P 4 ) release devices are employed. Most devices are constituted of a nylon skeleton covered with a silicon layer with P 4 . A device based on biopolymers was developed in order to reduce costs and decrease its environmental impact. In this study, we compared the kinetics of sustained progesterone release among devices manufactured with a polymeric blend made of polyhydroxybutyrate-valerate (PHBV) and poly-ε-caprolactone (PCL) (DISP) which were compared with DIB® (Internal Bovine Device) used as the control. In the in vitro and in vivo progesterone release tests, two types of biopolymer-based devices with a superficial area of 147 cm 2 were used: DISP8 (46% PHBV, 46% PCL and 8% P 4 ; n = 4), DISP10 (45% PHBV, 45% PCL, 10% P 4 ; n = 4) and DIB® (1 g P 4 , 120 cm 2 area; n = 3). The in vitro tests were carried out according to USP XXIII specifications and were performed in a dissolutor sink using an alcohol/water mixture (60/40 v/v) as a release media and samples were collected at 2 min, 2, 4, 8, 12, 24, 48, 60, 72, 84 and 96 h. P 4 concentrations were measured through spectrophotometry in a 244 nm long wave. Three to 3 comparisons of angular coefficients of the straight lines obtained by regression analysis of accumulated P 4 concentrations as a function of square root of time were carried out. Furthermore, the diffusion coefficient values of P 4 were also determined for DISP8 and DISP10. The results showed that the concentrations of P 4 were higher in the DISP10 (774.63 ± 45.26 μg/cm 2 /t 1 /2 ) compared to DISP8 (566.17 ± 3.68 μg/cm 2 /t 1 /2 ) (P < 0.05). However, both DISP10 and DISP8 P 4 concentrations did not differ from DIB® (677.39 ± 16.13 μg/cm 2 /t 1 /2 ). For the analysis of released quantities per day of the in vitro test, four periods were considered: 0-24, 24-48, 48-72 and 72-96 h. In the first 24 h, DISP8 released significantly less P 4 than DISP10 or DIB®, which did not differ among them. Between 24 and 48 h, DISP10 released significantly more P 4 than DIB®. DISP8 released an intermediate P 4 amount and did not differ significantly from DIB® or DISP10. Between 48 and 72 h, P 4 quantity released by DISP10 was significant higher (P < 0.01) than that of DIB® and DISP8, which did not differ among themselves. Between 72 and 96 h, DISP10 released significantly more P 4 than DIB®, and DISP8 released an intermediate amount which did not differ from DIB® or DISP10 (P < 0.01). There was interaction between treatment and time (P = 0.0024). The diffusion coefficient values were: 1.36 × 10 -8 (cm 2 /s) for DISP10 and 1.12 × 10 -8 (cm 2 /s) for DISP8. For the in vivo test, ovariectomized crossbred cows received DIB® (n = 4) or DISP8 (n = 8) in an alternate design with a non-balanced sequence (cross-over) added of measures repeated in time referring to 16 days of blood samples collection. Samples were analyzed through radioimmunoassay in solid phase using the commercial kit of DPC (Diagnostics Products Corporation). Plasma concentrations of P 4 peaked at 4 h after the placement of the device, this being the only time in which plasma P 4 concentrations differed between DIB® (11.45 ± 1.96) compared with DISP8 (9.23 ± 1.15 ng/mL) (P = 0.027). On day 8, plasma P 4 concentrations were similar for DIB® (2.44 ± 0.09) and DISP8 (1.89 ± 0.13 ng/mL) (P = 0.58) showing that both devices were able to keep P 4 concentrations above 1 ng/mL in the plasma of the cow during the 16 day in vivo test. In conclusion, devices manufactured with the blend of PHBV/PCL biopolymers can sustain the release of P 4 in a similar manner as silicon. © 2017 Japanese Society of Animal Science.

Depressed polymorphonuclear cell functions in periparturient cows that develop postpartum reproductive diseases.

PubMed

Islam, Rafiqul; Kumar, Harendra; Singh, Gyanendra; Krishnan, Binsila B; Dey, Sahadeb

2017-09-01

The study was planned to see if there is any important and significant changes in the PMN function in cows suffering from postpartum reproductive diseases (PRD). Blood sampling was done from 41 pregnant cows on 15 days prepartum (-15d), calving day (0d), 15 days (15d) and 30 days (30d) postpartum and thorough gynaecological examination was performed on 0d, 15d, 30d and 45d for diagnosis of PRD like retained placenta (RP), clinical metritis (CM), clinical endometritis (CE) and delayed involution of uterus (DIU). The heparinised blood was used for isolation of PMN leukocytes for estimation of superoxide (SO), hydrogen peroxide (H 2 O 2 ) and enzyme myeloperoxidase (MPO) activity in each group of cows. The SO production (ΔOD) was greater for normal (0.19 ± 0.05) than cows suffering from RP (-0.12 ± 0.09), CM (-0.15 ± 0.13) and CE (-0.07 ± 0.05) at -15d. The mean value was greater for normal cows (0.12) than the cows with PRD (0.05 to 0.9) at 30d. The H 2 O 2 production was greater for normal than cows with PRD at all sampling days and significantly greater than cows with RP and CE at 15d (p < 0.01) and 30d (P < 0.05). The MPO activity (μmol/1 × 10 7 ) was greater for normal (18.77 ± 1.27) than for RP (12.52 ± 2.57) and CM (11.31 ± 3.30) cows on 0d. The depressed capability of the PMN from the cows with PRD to produce SO, H 2 O 2 and MPO during the periparturient period indicated their association with the development of RP, CM and CE.

Composition and maturity of the 60013/14 core

NASA Technical Reports Server (NTRS)

Korotev, Randy L.; Morris, Richard V.; Lauer, Howard V., Jr.

1993-01-01

The 60013/14 double drive tube (62 cm deep) is one of three regolith cores taken 35-40 m apart in a triangular array on the Cayley plains at station 10' (LM/ALSEP), Apollo 16. This trio, which includes double drive tube 60009/10 (59 cm deep) and deep drill core 60001-7 (220 cm), is the only such array of cores returned from the Moon. The top 45 cm of 60013/14 is mature, as is surface reference soil 60601 taken nearby. Maturity generally decreases with depth, with soil below 45 cm being submature. The zone of lowest maturity (34 is less than or equal to I(sub s)/FeO is less than 50) extends from 46 to 58 cm depth, and corresponds to the distinct region of light-colored soil observed during core processing. In the other two cores, most of the compositional variation results from mixing between fine-grained, mature soil with 10-11 micro-g/g Sc and coarse-grained ferroan anorthosite consisting of greater than 99% plagioclase with less than 0.5 micro-g/g Sc. This is most evident in 60009/10 which contains a high abundance of plagioclase at about 54 cm depth (minimum Sc: 3-4 micro-g/g); a similar zone occurs in 60001-7 at 17-22 cm (MPU-C), although it is not as rich in plagioclase (minimum Sc: 6-7 micro-g/g). Compositional variations are less in 60013/14 than in the other two cores (range: 7.9-10.0 micro-g/g Sc), but are generally consistent with the 'plagioclase dilution' effect seen in 60009/10, i.e., most 60013/14 samples plot along the mixing line of 60009/10. However, a plagioclase component is not the cause of the lower maturity and lighter color of the unit at 46-58 cm depth in 60013/14. Many of the samples in this zone have distinctly lower Sm/Sc ratios than typical LM-area soils and plot off the mixing trend defined by 60009/10. This requires a component with moderately high Sc, but low-Sm/Sc, such as feldspathic fragmental breccia (FFB) or granulitic breccia. A component of Descartes regolith, such as occurs at North Ray Crater (NRC) and which is rich in FFB, could account for the composition of these soils (i.e., a 3:1 mixture of 60601 and NRC soil). It seems unlikely that NRC ejecta would occur half a meter deep at the LM station, thus this low-Sm/Sc component may result from an older, local crater that penetrated the Cayley surface layer and excavated underlying Descartes material, as did North Ray Crater. There is no evidence for such a unit or component in the other two cores. Soil below the light-colored unit (58-62) cm has 'typical' Sm/Sc ratios, but the lowest absolute Sc concentrations, i.e., it is compositionally equivalent to a mixture of surface soil and plagioclase such as that in ferroan anorthosite. This is the only soil that might be related to the plagioclase-rich units in the other two cores. Except for the mature soil at the top of each core and, perhaps, the plagioclase-rich layers, there is little compositional evidence for any common unit among the three cores. Soil corresponding to the mare-glass-bearing unit (MPU-B) and regolith-breccia-bearing unit (MPU-A) of 60001-7 do not occur in 60013/14 or 60009/10.

Doping effect on ferromagnetism, ferroelectricity and dielectric constant in sol-gel derived Bi1-xNdxFe1-yCoyO3 nanoceramics

NASA Astrophysics Data System (ADS)

Das, Sananda; Sahoo, R. C.; Bera, K. P.; Nath, T. K.

2018-04-01

Doping at the post-transition metal site by trivalent rare-earth ions and 3d transition metal site by transition metal ions in perovskite lattice has observed a variety of magnetic and electronic orders with spatially correlated charge, spin and orbital degrees of freedom. Here, we report large ferromagnetism and enhanced dielectric constant (at ∼100 Hz) in chemically synthesized single phase multiferroic Bi1-xNdxFe1-yCoyO3 (x = 0, 0.10; y = 0, 0.10) nanoparticles (average particles size ∼45 nm). We have also examined the ferroelectric nature of our chemically synthesized samples. The Rietveld refinement of the XRD data reveals the structural symmetry breaking from distorted rhombohedral R3c structure of BiFeO3 to the triclinic P1 structure in Bi0.9Nd0.1Fe0.9Co0.1O3 (BNFCO) without having any iron rich impurity phase. The magnetization in these nanoceramics most likely originates from the coexistence of mixed valence states of Fe ion (Fe2+ and Fe3+). A high room temperature dielectric constant (∼1050) has been observed at 100 Hz of BNFCO sample. The frequency dependent anomalies near Neel temperature of antiferromagnet in temperature variation of dielectric study have been observed for all the doped and co-doped samples exhibiting typical characteristic of relaxor ferroelectrics. A spectacular enhancement of remanent magnetization MR (∼7.2 emu/gm) and noticeably large coercivity HC (∼17.4 kOe) at 5 K have been observed in this BNFCO sample. Such emergence of ferromagnetic ordering indicates the canting of the surface spins at the surface boundaries because of the reduction of particle size in nanodimension. We have also observed P-E hysteresis loops with a remanent polarization of 26 μC/cm2 and coercive field of 5.6 kV/cm of this sample at room temperature. From impedance spectroscopy study the estimated activation energy of 0.41 eV suggests the semiconducting nature of our nanoceramic BNCFO sample.

Changes of Soil Aggregate C Isotopes in No-Till Corn Following Bromegrass.

NASA Astrophysics Data System (ADS)

Follett, R. F.; Varvel, G.; Vogel, K. P.

2007-12-01

This field study is near Ithaca, Nebraska, USA (lat. 41.151, long. 96.401) on a Filbert silt loam (fine, smectitic, mesic Vertic Argialboll). The site was in bromegrass since 1986. Corn was no-till seeded into the bromegrass sod in spring 1999. A randomized complete block design with three replicates was used. No-till corn was the main treatment with nitrogen (N) as subplots. N was broadcast at the start of each growing season at 60 or 120 kg N/ha as NH4NO3. Total biomass was measured by weighing 4.4 m of row in each plot. Soil samples were obtained in May 1999 (baseline sampling), Sept 1999, June 2000, Oct 2000, Sept 2001, Nov 2002, Sept 2003, and Oct 2005 from pre-selected areas by removal of plant material from the soil surface and removing the 0-5, 5- 10, and at 4 of the 8 harvests also sampling the 10-30 cm depths with a flat-bladed shovel. Soil bulk densities were determined on clods from each layer. The moist soil was passed through an 8 mm sieve before air drying and storing. Aggregate size fractions were obtained with a Yoder wet-aggregate method. Soil size fractions obtained were > 2, 1, 0.5, 0.25, 0.125, 0.045 and < 0.045 mm. Detritus was floated to the surface and skimmed off for transfer to a separate container. Aggregates were dried at 55°C, weighed, ground, and analyzed for total C and N and 13C:12C isotope ratio. Because soil organic carbon (SOC) was labeled with the bromegrass (C3 plant) isotope signature, then during the 77 months of this experiment the re-labeling of each fraction and the total SOC with the corn (C4 plant) isotope signature and the amounts of SOC lost from aggregate size fractions with conversion of the bromegrass sod to no-till corn was measured. During 6.5 years, total SOC decreased from 21.1, 17.0, and 55.8 t/ha in the 0-5, 5-10, and 10-30 cm depths to 20.1, 16.7, and 55.5 t/ha, respectively. However the SOC in the < 2, 0.5-2, and < 0.5 mm fractions of the 0 - 5 cm depth changed from 62, 21, and 16 % of the total SOC at the studies beginning to 31, 40, and 29 %, respectively, by the end of 77 months. Weight of SOC from C4 plants was 34.8, 49.8, and 73.2 % of total SOC in the 0-5, 5-10, and 0-30 cm depths, respectively at the beginning of the study, but after 77 months of no-till corn was 47.3, 59.0, and 71.8 % of total SOC for these same depths. In summary, it is important to evaluate losses or gains of SOC under cultivation. Use of the 13C:12C ratios, as influenced by reversing the growing sequence of C3 vs. C4 plants, allows losses of older SOC from C3 plants (bromegrass) vs. that added by growing C4 plants (corn) to be determined over time and allows rates of change of the SOC associated with various soil fractions to be evaluated.

Quantification of loosely associated and tightly associated bacteria on broiler carcass skin using swabbing, stomaching, and grinding methods.

PubMed

Singh, P; Lee, H C; Chin, K B; Ha, S D; Kang, I

2015-12-01

This research was conducted to quantify bacterial populations after swabbing or stomaching, followed by grinding the swabbed or stomached broiler skins. For each of 3 replications, 3 eviscerated broilers were randomly taken from a processing line in a local broiler processing plant. Ten swabs and 10 stomachs per bird were conducted on the left- and the right-side skins (10×7 cm), respectively, which were then finally ground. Results indicated that mesophilic aerobic bacteria (MAB) in the first swabbed sample were significantly lower than those in the first stomached sample (P<0.05), with no difference seen for the remaining sampling times (P>0.05). During 10 swabbings followed by final grinding, 8, 9, and 83% of MAB were detected after the first swabbing, after the second through 10th swabbings, and after final grinding of the skin, respectively. During 10 stomachings followed by the final grinding, 17, 18, and 65% of MAB were detected after the first stomaching, after the second through 10th stomachings, and after final grinding of the skin, respectively. Escherichia coli (E. coli) and coliforms were significantly higher in the first stomaching than those in the first swabbing (P<0.05), with no difference seen between the 2 sampling methods for the rest sampling times (P>0.05). Populations of E. coli and coliforms decreased step-wisely from the highest after grinding to the intermediate after first and second sampling, and to the least after 10th sampling (P<0.05), regardless of swabbing or grinding. In this study, less than 35% of MAB seemed loosely associated in the skin of eviscerated broiler, whereas more than 65% of MAB looked tightly associated, which were not recovered by stomaching or swabbing even 10 times but were recovered by grinding the skin. © 2015 Poultry Science Association Inc.

Structural, multiferroic, dielectric and magnetoelectric properties of (1-x)Ba0.85Ca0.15Ti0.90Zr0.10O3-(x)CoFe2O4 lead-free composites

NASA Astrophysics Data System (ADS)

Negi, N. S.; Kumar, Rakesh; Sharma, Hakikat; Shah, J.; Kotnala, R. K.

2018-06-01

High performance lead-free multiferroic composites with strong magnetoelectric coupling effect are desired to replace lead-based ceramics in multifunctional device applications due to increasing environmental issues. We report crystal structure, ferroelectric, magnetic, dielectric and magnetoelectric properties of (1-x)Ba0.85Ca0.15Ti0.90Zr0.10O3-(x)CoFe2O4 (BCTZ-CFO) lead-free composites with x = 0.1, 0.3, 0.5, 0.7 and 0.9 synthesized by chemical solution method. BCTZ power was synthesized by sol-gel method while CFO was prepared by metallo-organic decomposition (MOD) method. The XRD results confirm successful formation of the BCTZ-CFO composites without presence of any impurity phase. At room temperature, the BCTZ-CFO composites show multiferroic behavior characterized by ferroelectric and ferromagnetic hysteresis curves. The composite having 10 wt% of CFO exhibited maximum polarization, remnant polarization and coercive field of Ps ∼ 5.1 μC/cm2, Pr ∼ 1.4 μC/cm2 and Ec ∼ 11.6 kV/cm respectively. The BCTZ-CFO composite with 90 wt% of CFO incorporation exhibits improved ferromagnetic properties with Ms ∼ 32 emu/g, Mr ∼ 11.7 emu/g and Hc ∼ 504 Oe. Mӧssbauer spectra analysis show two sets of six-line hyperfine patterns for BCTZ-CFO composites, indicating the presence of Fe3+ ions in both A and B sites. Increasing BCTZ content was found to decrease the hyperfine field strength at both sites and is consistent with the decreasing magnetic moment observed for the samples. The maximum dielectric constant value ε‧ ∼ 678 is obtained at 1 MHz for composite with 10 wt% of CFO phase. The results indicate that the BCTZ-CFO composites are potential lead-free room temperature multiferroic systems.

Age-specific vibrissae growth rates: a tool for determining the timing of ecologically important events in Steller sea lions

USGS Publications Warehouse

Rea, L.D.; Christ, A.M.; Hayden, A.B.; Stegall, V.K.; Farley, S.D.; Stricker, Craig A.; Mellish, J.E.; Maniscalco, John M.; Waite, J.N.; Burkanov, V.N.; Pitcher, K.W.

2015-01-01

Steller sea lions (SSL; Eumetopias jubatus) grow their vibrissae continually, providing a multiyear record suitable for ecological and physiological studies based on stable isotopes. An accurate age-specific vibrissae growth rate is essential for registering a chronology along the length of the record, and for interpreting the timing of ecologically important events. We utilized four methods to estimate the growth rate of vibrissae in fetal, rookery pup, young-of-the-year (YOY), yearling, subadult, and adult SSL. The majority of vibrissae were collected from SSL live-captured in Alaska and Russia between 2000 and 2013 (n = 1,115), however, vibrissae were also collected from six adult SSL found dead on haul-outs and rookeries during field excursions to increase the sample size of this underrepresented age group. Growth rates of vibrissae were generally slower in adult (0.44 ± 0.15 cm/mo) and subadult (0.61 ± 0.10 cm/mo) SSL than in YOY (0.87 ± 0.28 cm/mo) and fetal (0.73 ± 0.05 cm/mo) animals, but there was high individual variability in these growth rates within each age group. Some variability in vibrissae growth rates was attributed to the somatic growth rate of YOY sea lions between capture events (P = 0.014, r2 = 0.206, n = 29).

WET EFFLUENT PARALLEL PLATE DIFFUSION DENUDER COUPLED CAPILLARY ION CHROMATOGRAPH FOR THE DETERMINATION OF ATMOSPHERIC TRACE GASES. (R825344)

EPA Science Inventory

We describe an inexpensive, compact parallel plate diffusion denuder coupled capillary IC system for the determination of soluble ionogenic atmospheric trace gases. The active sampling area (0.6×10 cm) of the denuder is formed in a novel manner by thermally bonding silica ge...

Benthic macrofauna data for San Francisco Bay, California, September 1986

USGS Publications Warehouse

Schemel, Laurence E.; Thompson, J.K.; Harmon, J.G.; Yost, B.T.

1995-01-01

Benthic macrofauna were collected during September 1986 to evaluate locations for long-term monitoring stations as part of the U.S. Geological Survey Regional Effects Monitoring Program in San Francisco Bay, California. Three to ten replicate samples were collected with a modified Van Veen sampler (0.05 m2 area) at ten locations. One box core sample (0.06 m2 area) was collected at seven to the ten locations. Six of the box core samples were split into an upper 10 cm sample and a deeper sample before analysis. Macrofauna specimens were identified to the lowest possible taxon, usually genus and species, then counted. An average of 88 percent of the benthic macrofauna specimens were identified to the species level. The fraction identified varied among stations from 54 to 98 percent. Nematodes and oligochaetes accounted for most of the unidentified specimens. Relative to the total number of species identified in five replicates at each location, an average of 90 percent of the species were collected with three replicates. In general, species with high to moderate abundances were present in all replicates, and species collected only after three or more replicates averaged less than one specimen per replicate. Results from the box cores showed that the dominant species were most abundant in the upper 10 cm, the depth of sediment that can be adequately sampled with a modified Van Veen sampler. On the basis of the number of species and their abundances at each location, seven of the ten locations were selected for sampling in the regular program, which began in March 1987.

Patterns and drivers of soil microbial communities in temperate grasslands on the Mongolian plateau

NASA Astrophysics Data System (ADS)

Yang, Y.; Hu, H.; Hao, B.; Liu, Y.; Chen, Y.; Ma, W.

2016-12-01

Soil microorganisms play key roles in regulating many important ecosystem processes. However, our understanding of the patterns and drivers of soil microbial communities at the regional scale remains limited. In this study, on the basis of phospholipid fatty acid (PLFA) analysis, we investigated large-scale patterns and drivers of soil microbial communities using data from 78 sites between two depths (0-10 cm and 10-20 cm) within three major grassland types (desert steppe, typical steppe, and meadow steppe) on the Mongolian Plateau. Our findings demonstrated that, at the regional scale, the total soil microbial biomass, fungal biomass, bacterial biomass, and actinomycete biomass in Inner Mongolian temperate grasslands were all positively associated with mean annual precipitation (MAP), soil organic carbon (SOC), soil total nitrogen (TN), C:N ratio, plant aboveground biomass (AGB), and plant species richness (SR), but negatively correlated with mean annual temperature (MAT), soil bulk density (BD), and soil pH in both depths, except actinomycete biomass with MAP and BD in 10-20 cm. A stepwise regression analysis revealed that soil microbial community variations in Inner Mongolian temperate grasslands were mainly explained by C : N ratio in 0-10 cm, but by SR (total soil microbial biomass, fungal biomass, and actinomycete biomass) and MAT (bacterial biomass) in 10-20 cm. Our findings strongly indicate that the dominant drivers of spatial variations in soil microbial communities between 0-10 cm and 10-20 cm in the Inner Mongolia grasslands are significantly different, with edaphic factors (e.g., C: N ratio) in 0-10 cm but climatic (e.g, MAT) and/or biotic (e.g, SR) in 10-20 cm.

Heavily Sn-doped GaAs with abrupt doping profiles grown by migration-enhanced epitaxy at low temperatures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chavanapranee, Tosaporn; Horikoshi, Yoshiji

The characteristics of heavily Sn-doped GaAs samples grown at 300 deg. C by a migration-enhanced epitaxy (MEE) technique are investigated in comparison with those of the samples grown by a conventional molecular-beam epitaxy (MBE) at 580 deg. C. While no discernible difference is observed in the low doping regime, the difference in doping characteristics between the MBE- and MEE-grown samples becomes apparent when the doping concentration exceeds 1x10{sup 19} cm{sup -3}. Sn atoms as high as 4x10{sup 21} cm{sup -3} can be incorporated into MEE-grown GaAs films, unlike the MBE-grown samples that have a maximum doping level limited around 1x10{supmore » 19} cm{sup -3}. Due to an effective suppression of Sn segregation in the MEE growth case, high quality GaAs films with abrupt high-concentration Sn-doping profiles are achieved with the doping concentrations of up to 2x10{sup 21} cm{sup -3}. It has been shown that even though a high concentration of Sn atoms is incorporated into the GaAs film, the electron concentration saturates at 6x10{sup 19} cm{sup -3} and then gradually decreases with Sn concentration. The uniform doping limitation, as well as the electron concentration saturation, is discussed by means of Hall-effect measurement, x-ray diffraction, and Raman scattering spectroscopy.« less

Analysis of a thioether lubricant by infrared Fourier microemission spectrophotometry

NASA Technical Reports Server (NTRS)

Jones, W. R., Jr.; Morales, W.; Lauer, J. L.

1986-01-01

An infrared Fourier microemission spectrophotometer is used to obtain spectra (wavenumber range, 630 to 1230 0.1 cm) from microgram quantities of thioether lubricant samples deposited on aluminum foil. Infrared bands in the spectra are reproducible and could be identified as originating from aromatic species (1,3-disubstituted benzenes). Spectra from all samples (neat and formulated, used and unused) are very similar. Additives (an acid and a phosphinate) present in low concentration (0.10 percent) in the formulated fluid are not detected. This instrument appears to be a viable tool in helping to identify lubricant components separated by liquid chromatography.

California GAMA Special Study. Development of a Capability for the Analysis of Krypton-85 in Groundwater Samples

DOE Office of Scientific and Technical Information (OSTI.GOV)

Visser, Ate; Bibby, Richard K.; Moran, Jean E.

A capability for the analysis of krypton-85 ( 85Kr) in groundwater samples was developed at LLNL. Samples are collected by extracting gas from 2000-4000 L of groundwater at the well, yielding approximately 0.2 cm 3 STP krypton. Sample collection takes 1 to 4 hours. Krypton is purified in the laboratory using a combination of molecular sieve and activated charcoal traps, and transferred to a liquid scintillation vial. The 85Kr activity is measured by liquid scintillation on a Quantulus 1220 liquid scintillation counter from PerkinElmer. The detection limit for a typical 0.2 cm 3Kr sample size is 11% of the presentmore » day activity in air, corresponding to the decay corrected activity in air in 1987. The typical measurement uncertainty is below 10% for recently recharged samples. Six groundwater samples were collected, purified and counted. 85Kr was not detected in any of the samples counted at LLNL. 85Kr was detected by the low level counting laboratory of Bern University in all samples between 1.5 and 6.6 decays per minute per cm 3 krypton, corresponding to decay corrected activities in air between 1971 and 1985. The new capability is an excellent complement to tritium-helium, expanding the existing suite of age dating tools available to the GAMA program ( 35S, 3H/ 3He, 14C and radiogenic helium). 85Kr can replace 3H/ 3He in settings where 3H/ 3He ages are impossible to determine (for example where terrigenic helium overwhelms tritiogenic helium) and provides additional insight into travel time distributions in complex mixed groundwater systems.« less

Study of muons from the direction of Cygnus X-3 using an underground proportional-tube array

NASA Astrophysics Data System (ADS)

Kochocki, J. A.; Allison, W. W.; Alner, G. J.; Ambats, I.; Ayres, D. S.; Balka, L. J.; Barr, G. D.; Barrett, W. L.; Benjamin, D.; Border, P.; Brooks, C. B.; Cobb, J. H.; Cockerill, D. J.; Coover, K.; Courant, H.; Dahlin, B.; Dasgupta, U.; Dawson, J. W.; Edwards, V. W.; Fields, T. H.; Kirby-Gallagher, L. M.; Garcia-Garcia, C.; Giles, R. H.; Goodman, M. C.; Heller, K.; Heppelman, S.; Hill, N.; Hoftiezer, J. H.; Jankowski, D. J.; Johns, K.; Joyce, T.; Kafka, T.; Litchfield, P. J.; Lopez, F. V.; Lowe, M.; Mann, W. A.; Marshak, M. L.; May, E. N.; McMaster, L.; Milburn, R. H.; Miller, W.; Napier, A.; Oliver, W. P.; Pearce, G. F.; Perkins, D. H.; Peterson, E. A.; Price, L. E.; Roback, D.; Rosen, D. B.; Ruddick, K.; Saitta, B.; Schlereth, J. L.; Schmid, D.; Schneps, J.; Shield, P. D.; Shupe, M.; Sundaralingam, N.; Thomson, M. A.; Thron, J. L.; Werkema, S.; West, N.

1990-11-01

From July 1987 through March 1988 an array of proportional wire modules was operated as a muon detector at a depth of 2090 meters water equivalent in the Soudan mine in northern Minnesota. A spatial angular resolution of 1.2° was achieved for muon tracking. A clean sample of 1.02×105 muon trajectories recorded underground is used to search for an excess flux of muons from the direction of Cygnus X-3. For muons within the phase interval [0.6, 0.9] of the source's 4.8-h period, 90%-C.L. upper limits for fluxes arriving within 3° and 1.5° half-angle cones centered on the Cygnus X-3 direction are 8.5×10-11 cm-2s-1 and 3.1×10-11 cm-2s-1, respectively.

Extended hot carrier lifetimes observed in bulk In{sub 0.265±0.02}Ga{sub 0.735}N under high-density photoexcitation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Yi; Tayebjee, Murad J. Y.; Smyth, Suntrana

2016-03-28

We have investigated the ultrafast carrier dynamics in a 1 μm bulk In{sub 0.265}Ga{sub 0.735}N thin film grown using energetic neutral atom-beam lithography/epitaxy molecular beam epitaxy. Cathodoluminescence and X-ray diffraction experiments are used to observe the existence of indium-rich domains in the sample. These domains give rise to a second carrier population and bi-exponential carrier cooling is observed with characteristic lifetimes of 1.6 and 14 ps at a carrier density of 1.3 × 10{sup 16 }cm{sup −3}. A combination of band-filling, screening, and hot-phonon effects gives rise to a two-fold enhanced mono-exponential cooling rate of 28 ps at a carrier density of 8.4 × 10{sup 18 }cm{sup −3}. Thismore » is the longest carrier thermalization time observed in bulk InGaN alloys to date.« less

Endoscopic ultrasonography does not differentiate neoplastic from non-neoplastic small gallbladder polyps.

PubMed

Cheon, Young Koog; Cho, Won Young; Lee, Tae Hee; Cho, Young Deok; Moon, Jong Ho; Lee, Joon Seong; Shim, Chan Sup

2009-05-21

To assess the ability of endoscopic ultrasonography (EUS) to differentiate neoplastic from non-neoplastic polypoid lesions of the gallbladder (PLGs). The uses of EUS and transabdominal ultrasonography (US) were retrospectively analyzed in 94 surgical cases of gallbladder polyps less than 20 mm in diameter. The prevalence of neoplastic lesions with a diameter of 5-10 mm was 17.2% (10/58); 11-15 mm, 15.4% (4/26), and 16-20 mm, 50% (5/10). The overall diagnostic accuracies of EUS and US for small PLGs were 80.9% and 63.9% (P < 0.05), respectively. EUS correctly distinguished 12 (63.2%) of 19 neoplastic PLGs but was less accurate for polyps less than 1.0 cm (4/10, 40%) than for polyps greater than 1.0 cm (8/9, 88.9%) (P = 0.02). Although EUS was more accurate than US, its accuracy for differentiating neoplastic from non-neoplastic PLGs less than 1.0 cm was low. Thus, EUS alone is not sufficient for determining a treatment strategy for PLGs of less than 1.0 cm.

Endoscopic ultrasonography does not differentiate neoplastic from non-neoplastic small gallbladder polyps

PubMed Central

Cheon, Young Koog; Cho, Won Young; Lee, Tae Hee; Cho, Young Deok; Moon, Jong Ho; Lee, Joon Seong; Shim, Chan Sup

2009-01-01

AIM: To assess the ability of endoscopic ultrasonography (EUS) to differentiate neoplastic from non-neoplastic polypoid lesions of the gallbladder (PLGs). METHODS: The uses of EUS and transabdominal ultrasonography (US) were retrospectively analyzed in 94 surgical cases of gallbladder polyps less than 20 mm in diameter. RESULTS: The prevalence of neoplastic lesions with a diameter of 5-10 mm was 17.2% (10/58); 11-15 mm, 15.4% (4/26), and 16-20 mm, 50% (5/10). The overall diagnostic accuracies of EUS and US for small PLGs were 80.9% and 63.9% (P < 0.05), respectively. EUS correctly distinguished 12 (63.2%) of 19 neoplastic PLGs but was less accurate for polyps less than 1.0 cm (4/10, 40%) than for polyps greater than 1.0 cm (8/9, 88.9%) (P = 0.02). CONCLUSION: Although EUS was more accurate than US, its accuracy for differentiating neoplastic from non-neoplastic PLGs less than 1.0 cm was low. Thus, EUS alone is not sufficient for determining a treatment strategy for PLGs of less than 1.0 cm. PMID:19452579

Development of a standard soil-to-skin adherence probability density function for use in Monte Carlo analyses of dermal exposure.

PubMed

Finley, B L; Scott, P K; Mayhall, D A

1994-08-01

It has recently been suggested that "standard" data distributions for key exposure variables should be developed wherever appropriate for use in probabilistic or "Monte Carlo" exposure analyses. Soil-on-skin adherence estimates represent an ideal candidate for development of a standard data distribution: There are several readily available studies which offer a consistent pattern of reported results, and more importantly, soil adherence to skin is likely to vary little from site-to-site. In this paper, we thoroughly review each of the published soil adherence studies with respect to study design, sampling, and analytical methods, and level of confidence in the reported results. Based on these studies, probability density functions (PDF) of soil adherence values were examined for different age groups and different sampling techniques. The soil adherence PDF developed from adult data was found to resemble closely the soil adherence PDF based on child data in terms of both central tendency (mean = 0.49 and 0.63 mg-soil/cm2-skin, respectively) and 95th percentile values (1.6 and 2.4 mg-soil/cm2-skin, respectively). Accordingly, a single, "standard" PDF is presented based on all data collected for all age groups. This standard PDF is lognormally distributed; the arithmetic mean and standard deviation are 0.52 +/- 0.9 mg-soil/cm2-skin. Since our review of the literature indicates that soil adherence under environmental conditions will be minimally influenced by age, sex, soil type, or particle size, this PDF should be considered applicable to all settings. The 50th and 95th percentile values of the standard PDF (0.25 and 1.7 mg-soil/cm2-skin, respectively) are very similar to recent U.S. EPA estimates of "average" and "upper-bound" soil adherence (0.2 and 1.0 mg-soil/cm2-skin, respectively).

High-Pressure Oxygenation of Mt-Ybco the way to Reduce the Oxygenation Time, to Prevent Macrocracking, and to Obtain Materials with High Critical Currents.

NASA Astrophysics Data System (ADS)

Prikhna, T. A.; Chaud, X.; Gawalek, W.; Joulain, A.; Rabier, J.; Moshchil, V. E.; Savchuk, Ya. M.; Sergienko, N. V.; Dub, S. N.; Melnikov, V. S.; Habisreuther, T.; Litzkendorf, D.; Bierlich, J.

2008-03-01

The oxygenation of MT-YBCO under isostatic oxygen pressure (up to 16 MPa) at 900-800 °C allowed reduced process time, lower macrocracking, and reduced microcracks. Additionally higher critical currents, trapped fields and mechanical characteristics can be attained. At 77 K thin-walled MT-YBCO had a jc in the ab plane of 85 kA/cm2 at 0 T and higher than 10 kA/cm2 in fields up to 5 T and the irreversibility field was 9.8 T. In the c-direction jc was 34 kA/cm2 in 0 T and higher than 2.5 kA/cm2 in a 10 T field. At 4.9 N-load the micohardness, Hv, was 8.7±0.3 GPa in the ab-plane and 7.6±0.3 GPa in the c-direction. The fracture toughness, K1C, was 2.5±0.1 MPaṡm0.5 (ab-plane) and 2.8±0.24 MPaṡm0.5 (c-direction). The samples with a higher twin density demonstrated a higher jc, especially in applied magnetic field. The twin density correlates with the sizes and distribution of Y211 grains in Y123. The thin-walled ceramics that demonstrated the highest jc contained about 22 twins in 1 μm and were practically free from dislocations and stacking faults. The maximal trapped field of the block of thin-walled ceramic oxygenated at 900-800 °C and 16 MPa was doubled as compared to that oxygenated at low temperature under ambient pressure.

Direct measurement of surface carbon concentrations. [in lunar soil

NASA Technical Reports Server (NTRS)

Filleux, C.; Tombrello, T. A.; Burnett, D. S.

1977-01-01

Measurements of surface concentrations of carbon in lunar soils and soil breccias provide information on the origin of carbon in the regolith. The reaction C-12 (d, p sub zero) is used to measure 'surface' and 'volume' concentrations in lunar samples. This method has a depth resolution of 1 micron, which permits only a 'surface' and a 'volume' component to be measured. Three of four Apollo 16 double drive tube samples show a surface carbon concentration of about 8 by 10 to the 14th power/sq cm, whereas the fourth sample gave 4 by 10 to the 14th power/sq cm. It can be convincingly shown that the measured concentration does not originate from fluorocarbon or hydrocarbon contaminants. Surface adsorbed layers of CO or CO2 are removed by a sputter cleaning procedure using a 2-MeV F beam. It is shown that the residual C concentration of 8 by 10 to the 14th power/sq cm cannot be further reduced by increased F fluence, and it is therefore concluded that it is truly lunar. If one assumes that the measured surface C concentration is a steady-state concentration determined only by a balance between solar-wind implantation and sputtering, a sputter erosion rate of 0.1 A/yr is obtained. However, it would be more profitable to use an independently derived sputter erosion rate to test the hypothesis of a solar-wind origin of the surface carbon.

Soil fungal community shift evaluation as a potential cadaver decomposition indicator.

PubMed

Chimutsa, Monica; Olakanye, Ayodeji O; Thompson, Tim J U; Ralebitso-Senior, T Komang

2015-12-01

Fungi metabolise organic matter in situ and so alter both the bio-/physico-chemical properties and microbial community structure of the ecosystem. In particular, they are responsible reportedly for specific stages of decomposition. Therefore, this study aimed to extend previous bacteria-based forensic ecogenomics research by investigating soil fungal community and cadaver decomposition interactions in microcosms with garden soil (20 kg, fresh weight) and domestic pig (Sus scrofa domesticus) carcass (5 kg, leg). Soil samples were collected at depths of 0-10 cm, 10-20 cm and 20-30 cm on days 3, 28 and 77 in the absence (control -Pg) and presence (experimental +Pg) of Sus scrofa domesticus and used for total DNA extraction and nested polymerase chain reaction and denaturing gradient gel electrophoresis (PCR-DGGE) profiling of the 18S rRNA gene. The Shannon-Wiener (H') community diversity indices were 1.25±0.21 and 1.49±0.30 for the control and experimental microcosms, respectively, while comparable Simpson species dominance (S) values were 0.65±0.109 and 0.75±0.015. Generally, and in contrast to parallel studies of the bacterial 16S rRNA and 16S rDNA profiles, statistical analysis (t-test) of the 18S dynamics showed no mathematically significant shifts in fungal community diversity (H'; p=0.142) and dominance (S; p=0.392) during carcass decomposition, necessitating further investigations. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

Increased net water loss by oral compared to nasal expiration in healthy subjects.

PubMed

Svensson, Sophie; Olin, Anna Carin; Hellgren, Johan

2006-03-01

To compare the difference in respiratory water loss during expiration through the nose and through the mouth, in healthy subjects. The study included 19 healthy, non-smoking volunteers without any present history of non-infectious rhinitis, presenting with symptoms of rhinitis, asthma or previous nasal surgery. Nasal and oral expiratory breath condensates were collected using a breath condenser during tidal respiration at indoor resting conditions. During the nasal breath condensate sampling, the subjects were breathing into a transparent face mask covering the nose and the mouth with the mouth closed. During the oral breath condensate sampling, the subjects inhaled through the nose and exhaled through a mouthpiece connected to the condenser. The airflow during the sampling was assessed with a dry-spirometer connected to the condenser. Sampling was stopped after 100 litres of expired air for each breathing mode. Nasal sampling was done before and after decongestion of the nasal mucosa with oxymetazoline, 0.5 mg/ml. The effect on the nasal mucosa was assessed with acoustic rhinometry. The mean loss of expired water was 42% less by nasal expiration before decongestion than by oral expiration (1.9 x 10(-3) g/L min compared to 2.7 x 10(-3) g/L min, p < 0.001). The mean expiratory minute ventilation was 9.0 L/min by nasal respiration and 9.8 L/min by oral respiration. Decongestion of the nasal mucosa showed a mean increase of the cross-sectional area at 4 cm from the nostril (1.44 to 1.67 cm2, p = 0.0024), but there was no effect on the net water loss (1.9 x 10(-3) g/Lmin vs 1.9 x 10(-3) g/Lmin). This study showed that the net water loss increased by 42% when the breathing mode was switched from nasal to oral expiration during tidal breathing in healthy subjects. Increased water and energy loss by oral breathing could be a contributing factor to the symptoms seen in patients suffering from nasal obstruction.

X-ray evidence for ultra-fast outflows in AGNs

NASA Astrophysics Data System (ADS)

Tombesi, Francesco; Sambruna, Rita; Braito, Valentina; Reeves, James; Reynolds, Christopher; Cappi, Massimo

2012-07-01

X-ray evidence for massive, highly ionized, ultra-fast outflows (UFOs) has been recently reported in a number of AGNs through the detection of blue-shifted Fe XXV/XXVI absorption lines. We present the results of a comprehensive spectral analysis of a large sample of 42 local Seyferts and 5 radio galaxies observed with XMM-Newton and Suzaku. We assessed the global detection significance of the absorption lines and performed a detailed photo-ionization modeling. We find that UFOs are common phenomena, being present in >40% of the sources. Their outflow velocity distribution is in the range ˜0.03--0.3c, with mean value of ˜0.14c. The ionization parameter is very high, in the range logξ˜3--6 erg~s^{-1}~cm, and the associated column densities are also large, in the range ˜10^{22}--10^{24} cm^{-2}. Their location is constrained at ˜0.0003--0.03pc (˜10^2--10^4 r_s) from the central black hole, consistent with what is expected for accretion disk winds/outflows. The mass outflow rates are in the interval ˜0.01--1M_{⊙}~yr^{-1} and the associated mechanical power is high, in the range ˜10^{43}--10^{45} erg/s. Therefore, UFOs are capable to provide a significant contribution to the AGN cosmological feedback and their study can provide important clues on the connection between accretion disks, winds and jets.

Extraction of citral oil from lemongrass (Cymbopogon Citratus) by steam-water distillation technique

NASA Astrophysics Data System (ADS)

Alam, P. N.; Husin, H.; Asnawi, T. M.; Adisalamun

2018-04-01

In Indonesia, production of citral oil from lemon grass (Cymbopogon Cytratus) is done by a traditional technique whereby a low yield results. To improve the yield, an appropriate extraction technology is required. In this research, a steam-water distillation technique was applied to extract the essential oil from the lemongrass. The effects of sample particle size and bed volume on yield and quality of citral oil produced were investigated. The drying and refining time of 2 hours were used as fixed variables. This research results that minimum citral oil yield of 0.53% was obtained on sample particle size of 3 cm and bed volume of 80%, whereas the maximum yield of 1.95% on sample particle size of 15 cm and bed volume of 40%. The lowest specific gravity of 0.80 and the highest specific gravity of 0.905 were obtained on sample particle size of 8 cm with bed volume of 80% and particle size of 12 cm with bed volume of 70%, respectively. The lowest refractive index of 1.480 and the highest refractive index of 1.495 were obtained on sample particle size of 8 cm with bed volume of 70% and sample particle size of 15 cm with bed volume of 40%, respectively. The solubility of the produced citral oil in alcohol was 70% in ratio of 1:1, and the citral oil concentration obtained was around 79%.

Determination of irradiated reactor uranium in soil samples in Belarus using 236U as irradiated uranium tracer.

PubMed

Mironov, Vladislav P; Matusevich, Janna L; Kudrjashov, Vladimir P; Boulyga, Sergei F; Becker, J Sabine

2002-12-01

This work presents experimental results on the distribution of irradiated reactor uranium from fallout after the accident at Chernobyl Nuclear Power Plant (NPP) in comparison to natural uranium distribution in different soil types. Oxidation processes and vertical migration of irradiated uranium in soils typical of the 30 km relocation area around Chernobyl NPP were studied using 236U as the tracer for irradiated reactor uranium and inductively coupled plasma mass spectrometry as the analytical method for uranium isotope ratio measurements. Measurements of natural uranium yielded significant variations of its concentration in upper soil layers from 2 x 10(-7) g g(-1) to 3.4 x 10(-6) g g(-1). Concentrations of irradiated uranium in the upper 0-10 cm soil layers at the investigated sampling sites varied from 5 x 10(-12) g g(-1) to 2 x 10(-6) g g(-1) depending on the distance from Chernobyl NPP. In the majority of investigated soil profiles 78% to 97% of irradiated "Chernobyl" uranium is still contained in the upper 0-10 cm soil layers. The physical and chemical characteristics of the soil do not have any significant influence on processes of fuel particle destruction. Results obtained using carbonate leaching of 236U confirmed that more than 60% of irradiated "Chernobyl" uranium is still in a tetravalent form, ie. it is included in the fuel matrix (non-oxidized fuel UO2). The average value of the destruction rate of fuel particles determined for the Western radioactive trace (k = 0.030 +/- 0.005 yr(-1)) and for the Northern radioactive trace (k = 0.035 + 0.009 yr(-1)) coincide within experimental errors. Use of leaching of fission products in comparison to leaching of uranium for study of the destruction rate of fuel particles yielded poor coincidence due to the fact that use of fission products does not take into account differences in the chemical properties of fission products and fuel matrix (uranium).

Low-frequency zone boundary phonons in Li doped ZnO ceramics

NASA Astrophysics Data System (ADS)

Yadav, Harish Kumar; Sreenivas, K.; Gupta, Vinay; Katiyar, R. S.

2008-09-01

Room temperature Raman spectra of Li doped ZnO (Zn1-xLixO) ceramics with varying Li concentrations (x =0.0, 0.05, 0.10, and 0.15) are investigated in this study. Four peaks were identified at 96.6, 127, 157, and 194 cm-1 in the Li doped samples. The peaks at 127, 157, and 194 cm-1 are assigned to zone boundary phonons in ZnO [J. M. Calleja and M. Cardona, Phys. Rev. B 16, 3753 (1977)], and appear due to disorder in ZnO lattice with Li incorporation. Lithium, owing to its smaller radius, adjusts itself anywhere in the ZnO lattice and breaks the crystal translational symmetry to a large extent, compared to other dopants. Disorder in the lattice is seen to be finely modulated with varying Li content. The peak at 96.6 cm-1 is hypothesized to be a projection of the vibrational motion of Li atoms at lower frequencies, which contributes in a major fashion at higher frequencies, due to its lighter mass than Zn or O atoms.

Post-Growth Annealing of Bridgman-grown CdZnTe and CdMnTe Crystals for Room-temperature Nuclear Radiation Detectors

DOE PAGES

Egarievwe, Stephen U.; Yang, Ge; Egarievwe, Alexander; ...

2015-02-11

Bridgman-grown cadmium zinc telluride (CdZnTe or CZT) and cadmium manganese telluride (CdMnTe or CMT) crystals often have Te inclusions that limit their performances as X-ray- and gamma-ray-detectors. We present here the results of post-growth thermal annealing aimed at reducing and eliminating Te inclusions in them. In a 2D analysis, we observed that the sizes of the Te inclusions declined to 92% during a 60-h annealing of CZT at 510 °C under Cd vapor. Further, tellurium inclusions were eliminated completely in CMT samples annealed at 570 °C in Cd vapor for 26 h, whilst their electrical resistivity fell by an ordermore » of 10 2. During the temperature-gradient annealing of CMT at 730 °C and an 18 °C/cm temperature gradient for 18 h in a vacuum of 10 -5 mbar, we observed the diffusion of Te from the sample, causing a reduction in size of the Te inclusions. For CZT samples annealed at 700 °C in a 10 °C/cm temperature gradient, we observed the migration of Te inclusions from a low-temperature region to a high one at 0.022 μm/s. During the temperature-gradient annealing of CZT in a vacuum of 10 -5 mbar at 570 °C and 30 °C/cm for 18 h, some Te inclusions moved toward the high-temperature side of the wafer, while other inclusions of the same size, i.e., 10 µm in diameter, remained in the same position. These results show that the migration, diffusion, and reaction of Te with Cd in the matrix of CZT- and CMT-wafers are complex phenomena that depend on certain conditions.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Egarievwe, Stephen U.; Yang, Ge; Egarievwe, Alexander

Bridgman-grown cadmium zinc telluride (CdZnTe or CZT) and cadmium manganese telluride (CdMnTe or CMT) crystals often have Te inclusions that limit their performances as X-ray- and gamma-ray-detectors. We present here the results of post-growth thermal annealing aimed at reducing and eliminating Te inclusions in them. In a 2D analysis, we observed that the sizes of the Te inclusions declined to 92% during a 60-h annealing of CZT at 510 °C under Cd vapor. Further, tellurium inclusions were eliminated completely in CMT samples annealed at 570 °C in Cd vapor for 26 h, whilst their electrical resistivity fell by an ordermore » of 10 2. During the temperature-gradient annealing of CMT at 730 °C and an 18 °C/cm temperature gradient for 18 h in a vacuum of 10 -5 mbar, we observed the diffusion of Te from the sample, causing a reduction in size of the Te inclusions. For CZT samples annealed at 700 °C in a 10 °C/cm temperature gradient, we observed the migration of Te inclusions from a low-temperature region to a high one at 0.022 μm/s. During the temperature-gradient annealing of CZT in a vacuum of 10 -5 mbar at 570 °C and 30 °C/cm for 18 h, some Te inclusions moved toward the high-temperature side of the wafer, while other inclusions of the same size, i.e., 10 µm in diameter, remained in the same position. These results show that the migration, diffusion, and reaction of Te with Cd in the matrix of CZT- and CMT-wafers are complex phenomena that depend on certain conditions.« less

Working group session report: Neutron beam line shielding.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Russell, G. J.; Ikedo, Y.

2001-01-01

We have examined the differences between a 2-D model and a 3-D model for designing the beam-line shield for the HIPPO instrument at the Lujan Center at the Los Alamos National Laboratory. We have calculated the total (neutron and gamma ray) dose equivalent rate coming out of the personal access ports from the HIPPO instrument experiment cave. In order to answer this question, we have investigated two possible worst-case scenarios: (a) failure of the T{sub 0}-chopper and no sample at the sample position; and (b) failure of the T{sub 0}-chopper with a thick sample (a piece of Inconel-718, 10 cmmore » diam by 30 cm long) at the sample position.« less

Balloon borne in-situ detection of OH in the stratosphere from 37 to 23 km

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stimpfle, R.M.; Lapson, L.B., Wennberg, P.O.; Anderson, J.G.

1989-12-01

The OH number density in the stratosphere has been measured over the altitude interval of 37 to 23 km at midday via balloon-borne gondola launched from Palestine, Texas on July 6, 1988. OH radicals are detected with a laser induced fluorescence instrument employing a 17 kHz repetition rate copper vapor laser pumped dye laser optically coupled to an enclosed flow, in-situ sampling chamber. OH abundances ranged from 88 {plus minus} 31 pptv (1.1 {plus minus} 0.4 {times} 10{sup 7} molec cm{sup {minus}3}) in the 36 to 35 km interval to 0.9 {plus minus} 0.8 pptv (8.7 {plus minus} 7.7 {times}10{supmore » 5} molec cm{sup {minus}3}) in the 24 to 23 km interval. The stated uncertainty ({plus minus} 1{sigma}) includes that from both measurement precision and accuracy. Simultaneous detection of ozone and water vapor densities was carried out with separate on-board instruments.« less

Determination of thallium at ultra-trace levels in water and biological samples using solid phase spectrophotometry

NASA Astrophysics Data System (ADS)

Amin, Alaa S.; El-Sharjawy, Abdel-Azeem M.; Kassem, Mohammed A.

2013-06-01

A new simple, very sensitive, selective and accurate procedure for the determination of trace amounts of thallium(III) by solid-phase spectrophotometry (SPS) has been developed. The procedure is based on fixation of Tl(III) as quinalizarin ion associate on a styrene-divinylbenzene anion-exchange resin. The absorbance of resin sorbed Tl(III) ion associate is measured directly at 636 and 830 nm. Thallium(I) was determined by difference measurements after oxidation of Tl(I) to Tl(III) with bromine. Calibration is linear over the range 0.5-12.0 μg L-1 of Tl(III) with relative standard deviation (RSD) of 1.40% (n = 10). The detection and quantification limits are 150 and 495 ng L-1 using 0.6 g of the exchanger. The molar absorptivity and Sandell sensitivity are also calculated and found to be 1.31 × 107 L mol-1 cm-1 and 0.00156 ng cm-2, respectively. The proposed procedure has been successfully applied to determine thallium in water, urine and serum samples.

Filtration coefficient of the axon membrane as measured with hydrostatic and osmotic methods.

PubMed

Vargas, F F

1968-01-01

The hydraulic conductivity of the membranes surrounding the giant axon of the squid, Dosidicus gigas, was measured. In some axons the axoplasm was partially removed by suction. Perfusion was then established by insertion of a second pipette. In other axons the axoplasm was left intact and only one pipette was inserted. In both groups hydrostatic pressure was applied by means of a water column in a capillary manometer. Displacement of the meniscus in time gave the rate of fluid flowing across the axon sheath. In both groups osmotic differences across the membrane were established by the addition of a test molecule to the external medium which was seawater. The hydraulic conductivity determined by application of hydrostatic pressure was 10.6 +/- 0.8.10(-8) cm/sec cm H(2)O in perfused axons and 3.2 +/- 0.6.10(-8) cm/sec cm H(2)O in intact axons. When the driving force was an osmotic pressure gradient the conductivity was 4.5 +/- 0.6 x 10(-10) cm/sec cm H(2)O and 4.8 +/- 0.9 x 10(-10) cm/sec cm H(2)O in perfused and intact axons, respectively. A comparable result was found when the internal solution was made hyperosmotic. The fluid flow was a linear function of the hydrostatic pressure up to 70 cm of water. Glycerol outflux and membrane conductance were increased 1.6 and 1.1 times by the application of hydrostatic pressure. These increments do not give an explanation of the difference between the filtration coefficients. Other possible explanations are suggested and discussed.

False Negative Rates of a Macrofoam-Swab Sampling Method with Low Surface Concentrations of Two Bacillus anthracis Surrogates via Real-Time PCR

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hutchison, Janine R.; Piepel, Gregory F.; Amidan, Brett G.

Surface sampling for Bacillus anthracis spores has traditionally relied on detection via bacterial cultivation methods. Although effective, this approach does not provide the level of organism specificity that can be gained through molecular techniques. False negative rates (FNR) and limits of detection (LOD) were determined for two B. anthracis surrogates with modified rapid viability-polymerase chain reaction (mRV-PCR) following macrofoam-swab sampling. This study was conducted in parallel with a previously reported study that analyzed spores using a plate-culture method. B. anthracis Sterne (BAS) or B. atrophaeus Nakamura (BG) spores were deposited onto four surface materials (glass, stainless steel, vinyl tile, andmore » plastic) at nine target concentrations (2 to 500 spores/coupon; 0.078 to 19.375 colony-forming units [CFU] per cm2). Mean FNR values for mRV-PCR analysis ranged from 0 to 0.917 for BAS and 0 to 0.875 for BG and increased as spore concentration decreased (over the concentrations investigated) for each surface material. FNRs based on mRV-PCR data were not statistically different for BAS and BG, but were significantly lower for glass than for vinyl tile. FNRs also tended to be lower for the mRV-PCR method compared to the culture method. The mRV-PCR LOD95 was lowest for glass (0.429 CFU/cm2 with BAS and 0.341 CFU/cm2 with BG) and highest for vinyl tile (0.919 CFU/cm2 with BAS and 0.917 CFU/cm2 with BG). These mRV-PCR LOD95 values were lower than the culture values (BAS: 0.678 to 1.023 CFU/cm2 and BG: 0.820 to 1.489 CFU/cm2). The FNR and LOD95 values reported in this work provide guidance for environmental sampling of Bacillus spores at low concentrations.« less

False Negative Rates of a Macrofoam-Swab Sampling Method with Low Surface Concentrations of Two Bacillus anthracis Surrogates via Real-Time PCR

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hutchison, Janine R.; Piepel, Gregory F.; Amidan, Brett G.

Surface sampling for Bacillus anthracis spores has traditionally relied on detection via bacterial cultivation methods. Although effective, this approach does not provide the level of organism specificity that can be gained through molecular techniques. False negative rates (FNR) and limits of detection (LOD) were determined for two B. anthracis surrogates with modified rapid viability-polymerase chain reaction (mRV-PCR) following macrofoam-swab sampling. This study was conducted in parallel with a previously reported study that analyzed spores using a plate-culture method. B. anthracis Sterne (BAS) or B. atrophaeus Nakamura (BG) spores were deposited onto four surface materials (glass, stainless steel, vinyl tile, andmore » plastic) at nine target concentrations (2 to 500 spores/coupon; 0.078 to 19.375 colony-forming units [CFU] per cm²). Mean FNR values for mRV-PCR analysis ranged from 0 to 0.917 for BAS and 0 to 0.875 for BG and increased as spore concentration decreased (over the concentrations investigated) for each surface material. FNRs based on mRV-PCR data were not statistically different for BAS and BG, but were significantly lower for glass than for vinyl tile. FNRs also tended to be lower for the mRV-PCR method compared to the culture method. The mRV-PCR LOD₉₅ was lowest for glass (0.429 CFU/cm² with BAS and 0.341 CFU/cm² with BG) and highest for vinyl tile (0.919 CFU/cm² with BAS and 0.917 CFU/cm² with BG). These mRV-PCR LOD₉₅ values were lower than the culture values (BAS: 0.678 to 1.023 CFU/cm² and BG: 0.820 to 1.489 CFU/cm²). The FNR and LOD₉₅ values reported in this work provide guidance for environmental sampling of Bacillus spores at low concentrations.« less

A passive integrative sampler for mercury vapor in air and neutral mercury species in water

USGS Publications Warehouse

Brumbaugh, W.G.; Petty, J.D.; May, T.W.; Huckins, J.N.

2000-01-01

A passive integrative mercury sampler (PIMS) based on a sealed polymeric membrane was effective for the collection and preconcentration of Hg0. Because the Hg is both oxidized and stabilized in the PIMS, sampling intervals of weeks to months are possible. The effective air sampling rate for a 15 x 2.5 cm device was about 21-equivalents/day (0.002 m3/day) and the detection limit for 4-week sampling was about 2 ng/m3 for conventional ICP-MS determination without clean-room preparation. Sampling precision was ??? 5% RSD for laboratory exposures, and 5-10% RSD for field exposures. These results suggest that the PIMS could be useful for screening assessments of Hg contamination and exposure in the environment, the laboratory, and the workplace. The PIMS approach may be particularly useful for applications requiring unattended sampling for extended periods at remote locations. Preliminary results indicate that sampling for dissolved gaseous mercury (DGM) and potentially other neutral mercury species from water is also feasible. Rigorous validation of the sampler performance is currently in progress. (C) 1999 Elsevier Science Ltd.A passive integrative mercury sampler (PIMS) based on a sealed polymeric membrane was effective for the collection and preconcentration of Hg0. Because the Hg is both oxidized and stabilized in the PIMS, sampling intervals of weeks to months are possible. The effective air sampling rate for a 15??2.5 cm device was about 21-equivalents/day (0.002 m3/day) and the detection limit for 4-week sampling was about 2 ng/m3 for conventional ICP-MS determination without clean-room preparation. Sampling precision was ???5% RSD for laboratory exposures, and 5-10% RSD for field exposures. These results suggest that the PIMS could be useful for screening assessments of Hg contamination and exposure in the environment, the laboratory, and the workplace. The PIMS approach may be particularly useful for applications requiring unattended sampling for extended periods at remote locations. Preliminary results indicate that sampling for dissolved gaseous mercury (DGM) and potentially other neutral mercury species from water is also feasible. Rigorous validation of the sampler performance is currently in progress.

Ex Vivo Characterization of Canine Liver Tissue Viscoelasticity Following High Intensity Focused Ultrasound (HIFU) Ablation

PubMed Central

Shahmirzadi, Danial; Hou, Gary Y.; Chen, Jiangang; Konofagou, Elisa E.

2014-01-01

Elasticity imaging has shown great promise in detecting High Intensity Focused Ultrasound (HIFU) lesions based on their distinct biomechanical properties. However, quantitative mechanical properties of the tissue and the optimal intensity for obtaining the best contrast parameters remain scarce. In this study, fresh canine livers were ablated using combinations of ISPTA intensities of 5.55, 7.16 and 9.07 kW/cm2 and time durations of 10 and 30 s ex vivo; leading to six groups of ablated tissues. Biopsy samples were then interrogated using dynamic shear mechanical testing within the range of 0.1-10 Hz to characterize the post-ablation tissue viscoelastic properties. All mechanical parameters were found to be frequency dependent. Compared to the unablated cases, all six groups of ablated tissues showed statistically-significant higher complex shear modulus and shear viscosity. However, among the ablated groups, both complex shear modulus and shear viscosity were found to monotonically increase in groups 1-4 (5.55 kW/cm2 for 10 s, 7.16 kW/cm2 for 10 s, 9.07 kW/cm2 & 10 s, and 5.55 kW/cm2 & 30 s, respectively), but decrease in groups 5 and 6 (7.16 kW/cm2 for 30 s, and 9.07 kW/cm2 for 30 s, respectively). For groups 5 and 6, the temperature was expected to exceed the boiling point, and therefore, the decreased stiffening could be due to the compromised integrity of the tissue microstructure. Future studies are needed to estimate the tissue mechanical properties in vivo and perform real-time monitoring of tissue alterations during ablation. PMID:24315395

Measurement of νμ-induced charged-current neutral pion production cross sections on mineral oil at Eν∈0.5-2.0GeV

NASA Astrophysics Data System (ADS)

Aguilar-Arevalo, A. A.; Anderson, C. E.; Bazarko, A. O.; Brice, S. J.; Brown, B. C.; Bugel, L.; Cao, J.; Coney, L.; Conrad, J. M.; Cox, D. C.; Curioni, A.; Dharmapalan, R.; Djurcic, Z.; Finley, D. A.; Fleming, B. T.; Ford, R.; Garcia, F. G.; Garvey, G. T.; Grange, J.; Green, C.; Green, J. A.; Hart, T. L.; Hawker, E.; Imlay, R.; Johnson, R. A.; Karagiorgi, G.; Kasper, P.; Katori, T.; Kobilarcik, T.; Kourbanis, I.; Koutsoliotas, S.; Laird, E. M.; Linden, S. K.; Link, J. M.; Liu, Y.; Liu, Y.; Louis, W. C.; Mahn, K. B. M.; Marsh, W.; Mauger, C.; McGary, V. T.; McGregor, G.; Metcalf, W.; Meyers, P. D.; Mills, F.; Mills, G. B.; Monroe, J.; Moore, C. D.; Mousseau, J.; Nelson, R. H.; Nienaber, P.; Nowak, J. A.; Osmanov, B.; Ouedraogo, S.; Patterson, R. B.; Pavlovic, Z.; Perevalov, D.; Polly, C. C.; Prebys, E.; Raaf, J. L.; Ray, H.; Roe, B. P.; Russell, A. D.; Sandberg, V.; Schirato, R.; Schmitz, D.; Shaevitz, M. H.; Shoemaker, F. C.; Smith, D.; Soderberg, M.; Sorel, M.; Spentzouris, P.; Spitz, J.; Stancu, I.; Stefanski, R. J.; Sung, M.; Tanaka, H. A.; Tayloe, R.; Tzanov, M.; van de Water, R. G.; Wascko, M. O.; White, D. H.; Wilking, M. J.; Yang, H. J.; Zeller, G. P.; Zimmerman, E. D.

2011-03-01

Using a custom 3-Čerenkov ring fitter, we report cross sections for νμ-induced charged-current single π0 production on mineral oil (CH2) from a sample of 5810 candidate events with 57% signal purity over an energy range of 0.5-2.0 GeV. This includes measurements of the absolute total cross section as a function of neutrino energy, and flux-averaged differential cross sections measured in terms of Q2, μ- kinematics, and π0 kinematics. The sample yields a flux-averaged total cross section of (9.2±0.3stat±1.5syst)×10-39cm2/CH2 at mean neutrino energy of 0.965 GeV.

Development of an inconel self powered neutron detector for in-core reactor monitoring

NASA Astrophysics Data System (ADS)

Alex, M.; Ghodgaonkar, M. D.

2007-04-01

The paper describes the development and testing of an Inconel600 (2 mm diameter×21 cm long) self-powered neutron detector for in-core neutron monitoring. The detector has 3.5 mm overall diameter and 22 cm length and is integrally coupled to a 12 m long mineral insulated cable. The performance of the detector was compared with cobalt and platinum detectors of similar dimensions. Gamma sensitivity measurements performed at the 60Co irradiation facility in 14 MR/h gamma field showed values of -4.4×10 -18 A/R/h/cm (-9.3×10 -24 A/ γ/cm 2-s/cm), -5.2×10 -18 A/R/h/cm (-1.133×10 -23 A/ γ/cm 2-s/cm) and 34×10 -18 A/R/h/cm (7.14×10 -23 A/ γ/cm 2-s/cm) for the Inconel, Co and Pt detectors, respectively. The detectors together with a miniature gamma ion chamber and fission chamber were tested in the in-core Apsara Swimming Pool type reactor. The ion chambers were used to estimate the neutron and gamma fields. With an effective neutron cross-section of 4b, the Inconel detector has a total sensitivity of 6×10 -23 A/nv/cm while the corresponding sensitivities for the platinum and cobalt detectors were 1.69×10 -22 and 2.64×10 -22 A/nv/cm. The linearity of the detector responses at power levels ranging from 100 to 200 kW was within ±5%. The response of the detectors to reactor scram showed that the prompt response of the Inconel detector was 0.95 while it was 0.7 and 0.95 for the platinum and cobalt self-powered detectors, respectively. The detector was also installed in the horizontal flux unit of 540 MW Pressurised Heavy Water Reactor (PHWR). The neutron flux at the detector location was calculated by Triveni code. The detector response was measured from 0.02% to 0.07% of full power and showed good correlation between power level and detector signals. Long-term tests and the dynamic response of the detector to shut down in PHWR are in progress.

[Assessment of the air quality improment of cleaning and disinfection on central air-conditioning ventilation system].

PubMed

Liu, Hongliang; Zhang, Lei; Feng, Lihong; Wang, Fei; Xue, Zhiming

2009-09-01

To assess the effect of air quality of cleaning and disinfection on central air-conditioning ventilation systems. 102 air-conditioning ventilation systems in 46 public facilities were sampled and investigated based on Hygienic assessment criterion of cleaning and disinfection of public central air-conditioning systems. Median dust volume decreased from 41.8 g/m2 to 0.4 g/m2, and the percentage of pipes meeting the national standard for dust decreased from 17.3% (13/60) to 100% (62/62). In the dust, median aerobic bacterial count decreased from 14 cfu/cm2 to 1 cfu/cm2. Median aerobic fungus count decreased from 10 cfu/cm2 to 0 cfu/cm2. The percentage of pipes with bacterial and fungus counts meeting the national standard increased from 92.4% (171/185) and 82.2% (152/185) to 99.4% (165/166) and 100% (166/166), respectively. In the ventilation air, median aerobic bacterial count decreased from 756 cfu/m3 to 229 cfu/m3. Median aerobic fungus count decreased from 382 cfu/m3 to 120 cfu/m3. The percentage of pipes meeting the national standard for ventilation air increased from 33.3% (81/243) and 62.1% (151/243) to 79.8% (292/366) and 87.7% (242/276), respectively. But PM10 rose from 0.060 mg/m3 to 0.068 mg/m3, and the percentage of pipes meeting the national standard for PM10 increased from 74.2% (13/60) to 90.2% (46/51). The cleaning and disinfection of central air-conditioning ventilation systems could have a beneficial effect of air quality.

Study of ocular transport of drugs released from an intravitreal implant using magnetic resonance imaging.

PubMed

Kim, Hyuncheol; Lizak, Martin J; Tansey, Ginger; Csaky, Karl G; Robinson, Michael R; Yuan, Peng; Wang, Nam Sun; Lutz, Robert J

2005-02-01

Ensuring optimum delivery of therapeutic agents in the eye requires detailed information about the transport mechanisms and elimination pathways available. This knowledge can guide the development of new drug delivery devices. In this study, we investigated the movement of a drug surrogate, Gd-DTPA (Magnevist) released from a polymer-based implant in rabbit vitreous using T1-weighted magnetic resonance imaging (MRI). Intensity values in the MRI data were converted to concentration by comparison with calibration samples. Concentration profiles approaching pseudosteady state showed gradients from the implant toward the retinal surface, suggesting that diffusion was occurring into the retinal-choroidal-scleral (RCS) membrane. Gd-DTPA concentration varied from high values near the implant to lower values distal to the implant. Such regional concentration differences throughout the vitreous may have clinical significance when attempting to treat ubiquitous eye diseases using a single positional implant. We developed a finite element mathematical model of the rabbit eye and compared the MRI experimental concentration data with simulation concentration profiles. The model utilized a diffusion coefficient of Gd-DTPA in the vitreous of 2.8 x 10(-6) cm2 s(-1) and yielded a diffusion coefficient for Gd-DTPA through the simulated composite posterior membrane (representing the retina-choroidsclera membrane) of 6.0 x 10(-8) cm2 s(-1). Since the model membrane was 0.03-cm thick, this resulted in an effective membrane permeability of 2.0 x 10(-6) cm s(-1). Convective movement of Gd-DTPA was shown to have minimal effect on the concentration profiles since the Peclet number was 0.09 for this system.

The wettability of selected organic soils in Poland

NASA Astrophysics Data System (ADS)

Całka, A.; Hajnos, M.

2009-04-01

The wettability was measured in the laboratory by means of two methods: Water Drop Penetration Time (WDPT) test and Thin Column Wicking (TCW) method. WDPT is fast and simple method and was used to investigate potential water repellency of analyzed samples. TCW is an indirect method and was used to determine contact angles and surface free energy components. The measurement was performed in horizontal teflon chambers for thin-layer chromatography, adapted for tubes 10 cm long. The experiment was carried out on muck soils (samples were taken from two levels of soil profile: 0-20 cm and 20-40 cm) and peat soils. There were two types of peats: low-moor peats and high moor peats. Samples of low-moor peats were taken from level 25-75 cm (alder peat) and 75-125cm (sedge peat) and 25-75 cm (peloid peat). Samples of high moor peats from level 25-175 cm (sphagnum peat) and 175-225 cm (sphagnum peat with Eriophorum). There was found no variability in persistence of potential water repellency but there were differences in values of contact angles of individual soil samples. Both muck and peat samples are extremely water repellent soils. Water droplets persisted on the surface of soils for more than 24 hours. Contact angles and surface free energy components for all samples were differentiated. Ranges of water contact angles for organic soils are from 27,54o to 96,50o. The highest values of contact angles were for sphagnum peats, and the lowest for muck soil from 20-40 cm level. It means, that there are differences in wettability between these samples. Muck soil is the best wettable and sphagnum peats is the worst wettable soil. If the content of organic compounds in the soil exceeds 40% (like in peats), the tested material displays only dispersion-type interactions. Therefore for peat soils, the technique of thin column wicking could only be used to determine the dispersive component γiLW. For muck soils it was also determined electron-acceptor (Lewis acid) γ+ and electron-donor (Lewis base) γ- surface free energy components. The authors gratefully acknowledge the Ministry of Science and Higher Education for financial support of this work (grant No. N N310 149335).

Using a respiratory navigator significantly reduces variability when quantifying left ventricular torsion with cardiovascular magnetic resonance.

PubMed

Hamlet, Sean M; Haggerty, Christopher M; Suever, Jonathan D; Wehner, Gregory J; Andres, Kristin N; Powell, David K; Charnigo, Richard J; Fornwalt, Brandon K

2017-03-01

Left ventricular (LV) torsion is an important indicator of cardiac function that is limited by high inter-test variability (50% of the mean value). We hypothesized that this high inter-test variability is partly due to inconsistent breath-hold positions during serial image acquisitions, which could be significantly improved by using a respiratory navigator for cardiovascular magnetic resonance (CMR) based quantification of LV torsion. We assessed respiratory-related variability in measured LV torsion with two distinct experimental protocols. First, 17 volunteers were recruited for CMR with cine displacement encoding with stimulated echoes (DENSE) in which a respiratory navigator was used to measure and then enforce variability in end-expiratory position between all LV basal and apical acquisitions. From these data, we quantified the inter-test variability of torsion in the absence and presence of enforced end-expiratory position variability, which established an upper bound for the expected torsion variability. For the second experiment (in 20 new, healthy volunteers), 10 pairs of cine DENSE basal and apical images were each acquired from consecutive breath-holds and consecutive navigator-gated scans (with a single acceptance position). Inter-test variability of torsion was compared between the breath-hold and navigator-gated scans to quantify the variability due to natural breath-hold variation. To demonstrate the importance of these variability reductions, we quantified the reduction in sample size required to detect a clinically meaningful change in LV torsion with the use of a respiratory navigator. The mean torsion was 3.4 ± 0.2°/cm. From the first experiment, enforced variability in end-expiratory position translated to considerable variability in measured torsion (0.56 ± 0.34°/cm), whereas inter-test variability with consistent end-expiratory position was 57% lower (0.24 ± 0.16°/cm, p < 0.001). From the second experiment, natural respiratory variability from consecutive breath-holds translated to a variability in torsion of 0.24 ± 0.10°/cm, which was significantly higher than the variability from navigator-gated scans (0.18 ± 0.06°/cm, p = 0.02). By using a respiratory navigator with DENSE, theoretical sample sizes were reduced from 66 to 16 and 26 to 15 as calculated from the two experiments. A substantial portion (22-57%) of the inter-test variability of LV torsion can be reduced by using a respiratory navigator to ensure a consistent breath-hold position between image acquisitions.

Optimization of a novel large field of view distortion phantom for MR-only treatment planning.

PubMed

Price, Ryan G; Knight, Robert A; Hwang, Ken-Pin; Bayram, Ersin; Nejad-Davarani, Siamak P; Glide-Hurst, Carri K

2017-07-01

MR-only treatment planning requires images of high geometric fidelity, particularly for large fields of view (FOV). However, the availability of large FOV distortion phantoms with analysis software is currently limited. This work sought to optimize a modular distortion phantom to accommodate multiple bore configurations and implement distortion characterization in a widely implementable solution. To determine candidate materials, 1.0 T MR and CT images were acquired of twelve urethane foam samples of various densities and strengths. Samples were precision-machined to accommodate 6 mm diameter paintballs used as landmarks. Final material candidates were selected by balancing strength, machinability, weight, and cost. Bore sizes and minimum aperture width resulting from couch position were tabulated from the literature (14 systems, 5 vendors). Bore geometry and couch position were simulated using MATLAB to generate machine-specific models to optimize the phantom build. Previously developed software for distortion characterization was modified for several magnet geometries (1.0 T, 1.5 T, 3.0 T), compared against previously published 1.0 T results, and integrated into the 3D Slicer application platform. All foam samples provided sufficient MR image contrast with paintball landmarks. Urethane foam (compressive strength ∼1000 psi, density ~20 lb/ft 3 ) was selected for its accurate machinability and weight characteristics. For smaller bores, a phantom version with the following parameters was used: 15 foam plates, 55 × 55 × 37.5 cm 3 (L×W×H), 5,082 landmarks, and weight ~30 kg. To accommodate > 70 cm wide bores, an extended build used 20 plates spanning 55 × 55 × 50 cm 3 with 7,497 landmarks and weight ~44 kg. Distortion characterization software was implemented as an external module into 3D Slicer's plugin framework and results agreed with the literature. The design and implementation of a modular, extendable distortion phantom was optimized for several bore configurations. The phantom and analysis software will be available for multi-institutional collaborations and cross-validation trials to support MR-only planning. © 2017 The Authors. Journal of Applied Clinical Medical Physics published by Wiley Periodicals, Inc. on behalf of American Association of Physicists in Medicine.

Design of a boron neutron capture enhanced fast neutron therapy assembly

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Zhonglu

The use of boron neutron capture to boost tumor dose in fast neutron therapy has been investigated at several fast neutron therapy centers worldwide. This treatment is termed boron neutron capture enhanced fast neutron therapy (BNCEFNT). It is a combination of boron neutron capture therapy (BNCT) and fast neutron therapy (FNT). It is believed that BNCEFNT may be useful in the treatment of some radioresistant brain tumors, such as glioblastoma multiform (GBM). A boron neutron capture enhanced fast neutron therapy assembly has been designed for the Fermilab Neutron Therapy Facility (NTF). This assembly uses a tungsten filter and collimator nearmore » the patient's head, with a graphite reflector surrounding the head to significantly increase the dose due to boron neutron capture reactions. The assembly was designed using Monte Carlo radiation transport code MCNP version 5 for a standard 20x20 cm 2 treatment beam. The calculated boron dose enhancement at 5.7-cm depth in a water-filled head phantom in the assembly with a 5x5 cm 2 collimation was 21.9% per 100-ppm 10B for a 5.0-cm tungsten filter and 29.8% for a 8.5-cm tungsten filter. The corresponding dose rate for the 5.0-cm and 8.5-cm thick filters were 0.221 and 0.127 Gy/min, respectively; about 48.5% and 27.9% of the dose rate of the standard 10x10 cm 2 fast neutron treatment beam. To validate the design calculations, a simplified BNCEFNT assembly was built using four lead bricks to form a 5x5 cm 2 collimator. Five 1.0-cm thick 20x20 cm 2 tungsten plates were used to obtain different filter thicknesses and graphite bricks/blocks were used to form a reflector. Measurements of the dose enhancement of the simplified assembly in a water-filled head phantom were performed using a pair of tissue-equivalent ion chambers. One of the ion chambers is loaded with 1000-ppm natural boron (184-ppm 10B) to measure dose due to boron neutron capture. The measured dose enhancement at 5.0-cm depth in the head phantom for the 5.0-cm thick tungsten filter is (16.6 ± 1.8)%, which agrees well with the MCNP simulation of the simplified BNCEFNT assembly, (16.4 ± 0.5)%. The error in the calculated dose enhancement only considers the statistical uncertainties. The total dose rate measured at 5.0-cm depth using the non-borated ion chamber is (0.765 ± 0.076) Gy/MU, about 61% of the fast neutron standard dose rate (1.255Gy/MU) at 5.0-cm depth for the standard 10x10 cm 2 treatment beam. The increased doses to other organs due to the use of the BNCEFNT assembly were calculated using MCNP5 and a MIRD phantom. The activities of the activation products produced in the BNCEFNT assembly after neutron beam delivery were computed. The photon ambient dose rate due to the radioactive activation products was also estimated.« less

A Laboratory Railgun for Terminal Ballistics and Arc Armature Research Studies

DTIC Science & Technology

1987-06-01

Projectile Velocity Profile 3000 2500 - 2000 U.4J 500 0 1000 -Bank Energy - 4.5 MJ Rail Height - 3 cm Rail Thickness - I cm Injection Vel . - 300 rn/s...1250 Rail Height - 3 cm Rail Thickness - i cm Injection Vel . - 300 m/s 1000 c 750 L U 500 250 0 I I 0.0 0.5 1.0 1.5 2.0 2.5 3.0 Time. ms Figure 2.10... Vel . - 300 m/s L/R - 5 ms U S200 L ISO C- Si i5 to-000 50 0 0 2 3 Position Wm) Figure 2.11. Baseline Design Pressure Profile barrel length to

Effect of recombinant bovine somatotropin (rbST) on cytoplasmic maturation of bovine oocytes and their developmental competence in vitro.

PubMed

Kuzmina, Tatjana I; Alm, Hannelore; Denisenko, Vitaly; Tuchscherer, Armin; Kanitz, Wilhelm; Torner, Helmut

2007-04-01

The objectives of this study were to evaluate the effects of recombinant bovine somatotropin (rbST) on the nuclear and cytoplasmic maturation of bovine oocytes and their further developmental competence to blastocysts in vitro. We analyzed the mitochondrial activity and concentration of intracellular stored calcium ([Ca(2+)](is)) in matured oocytes and the morphology and chromatin status of produced embryos after in vitro fertilization. Cumulus-oocyte complexes were incubated in TCM 199 containing 10% fetal calf serum (control medium 1: CM 1) or 10% estrus cow serum (control medium 2: CM 2). The culture medium of the treatment groups was modified by supplementation of the control medium with 10 ng/ml rbST (CM 1A and CM 2A), 10(6)/ml granulosa cells (CM 1B and CM 2B), or 10 ng/ml rbST plus 10(6)/ml granulosa cells (CM 1C and CM 2C). No differences were observed in the percentages of oocytes reaching metaphase II between the groups. However, the proportion of blastocysts was highest in treatment groups CM 1C and CM 2C (P<0.05). The type of serum did not alter the positive effect of rbST on the developmental competence of embryos. The fluorescence intensity of metabolically active mitochondria measured by intensity per oocyte (Em 570) after MitoTracker CMTM Ros Orange labeling was significantly increased in oocytes matured in the presence of 10 ng/ml rbST and granulosa cells (309.21 vs. 119.97 microA; P<0.01). In parallel, the concentration of [Ca(2+)](is) in oocytes, determined using fluorophore chlortetracycline, was significantly decreased (0.85 +/- 0.02 vs. 0.97 +/- 0.03 AU; P<0.05). Based on these results, we concluded that rbST, in interaction with granulosa cells stimulates the oxidative activity of ooplasmic mitochondria and decreases the content of [Ca(2+)](is) in oocytes. These facts support the hypothesis that somatotropin influences the developmental competence of bovine oocytes during maturation in vitro, and this effect can be modulated by granulosa cells.

30 CFR 14.22 - Test for flame resistance of conveyor belts.

Code of Federal Regulations, 2010 CFR

2010-07-01

... the front of the rails and 1 ± 1/8 inch (2.5 ± 0.3 cm) from the outer lengthwise edge of each rail; (3... holes approximately 9/32 inch (0.7 cm) in diameter along both edges of the belt sample, starting at the first rail hole within 2 inches (5.1 cm) from the front edge of the sample. Make the next hole 5 ± 1/4...