Test, Control and Monitor System maintenance plan

NASA Technical Reports Server (NTRS)

Buehler, David P.; Lougheed, M. J.

1993-01-01

The maintenance requirements for Test, Control, and Monitor System (TCMS) and the method for satisfying these requirements prior to First Need Date (FND) of the last TCMS set are described. The method for satisfying maintenance requirements following FND of the last TCMS set will be addressed by a revision to this plan. This maintenance plan serves as the basic planning document for maintenance of this equipment by the NASA Payloads Directorate (CM) and the Payload Ground Operations Contractor (PGOC) at KSC. The terms TCMS Operations and Maintenance (O&M), Payloads Logistics, TCMS Sustaining Engineering, Payload Communications, and Integrated Network Services refer to the appropriate NASA and PGOC organization. For the duration of their contract, the Core Electronic Contractor (CEC) will provide a Set Support Team (SST). One of the primary purposes of this team is to help NASA and PGOC operate and maintain TCMS. It is assumed that SST is an integral part of TCMS O&M. The purpose of this plan is to describe the maintenance concept for TCMS hardware and system software in order to facilitate activation, transition planning, and continuing operation. When software maintenance is mentioned in this plan, it refers to maintenance of TCMS system software.

The Aristotelian Principle and Education.

ERIC Educational Resources Information Center

Pekarsky, Daniel

1980-01-01

For the Aristotelian principle to become operative, certain principles must be met. Individuals should be free from anxiety about satisfying basic needs. They cannot enjoy complexity in their lives beyond a certain point. To have satisfying lives, individuals should engage in both passive and active enjoyments, leading from a lower to a higher…

SPECS: Secure and Privacy Enhancing Communications Schemes for VANETs

NASA Astrophysics Data System (ADS)

Chim, T. W.; Yiu, S. M.; Hui, L. C. K.; Jiang, Zoe L.; Li, Victor O. K.

Vehicular ad hoc network (VANET) is an emerging type of networks which facilitates vehicles on roads to communicate for driving safety. The basic idea is to allow arbitrary vehicles to broadcast ad hoc messages (e.g. traffic accidents) to other vehicles. However, this raises the concern of security and privacy. Messages should be signed and verified before they are trusted while the real identity of vehicles should not be revealed, but traceable by authorized party. Existing solutions either rely heavily on a tamper-proof hardware device, or cannot satisfy the privacy requirement and do not have an effective message verification scheme. In this paper, we provide a software-based solution which makes use of only two shared secrets to satisfy the privacy requirement and gives lower message overhead and at least 45% higher successful rate than previous solutions in the message verification phase using the bloom filter and the binary search techniques. We also provide the first group communication protocol to allow vehicles to authenticate and securely communicate with others in a group of known vehicles.

A near-optimum procedure for selecting stations in a streamgaging network

USGS Publications Warehouse

Lanfear, Kenneth J.

2005-01-01

Two questions are fundamental to Federal government goals for a network of streamgages which are operated by the U.S. Geological Survey: (1) how well does the present network of streamagaging stations meet defined Federal goals and (2) what is the optimum set of stations to add or reactivate to support remaining goals? The solution involves an incremental-stepping procedure that is based on Basic Feasible Incremental Solutions (BFIS?s) where each BFIS satisfies at least one Federal streamgaging goal. A set of minimum Federal goals for streamgaging is defined to include water measurements for legal compacts and decrees, flooding, water budgets, regionalization of streamflow characteristics, and water quality. Fully satisfying all these goals by using the assumptions outlined in this paper would require adding 887 new streamgaging stations to the U.S. Geological Survey network and reactivating an additional 857 stations that are currently inactive.

Profile design for wings and propellers

NASA Technical Reports Server (NTRS)

Quast, A.; Horstmann, K. H.

1984-01-01

It has now become customary to develop profiles for wings and propellers for a given employment of the aircraft. This is possible because methods and computers are available to study an entire series of variants in comparatively short time. The basic viewpoints for profile design are presented. It is shown that laminarization has its advantages in almost all cases, including the design of a turbine blade and the design of the profile of an airliner. The requirements which profiles have to satisfy are discussed along with the possibilities for increasing lift on profiles.

Making sense by making sentient: effectance motivation increases anthropomorphism.

PubMed

Waytz, Adam; Morewedge, Carey K; Epley, Nicholas; Monteleone, George; Gao, Jia-Hong; Cacioppo, John T

2010-09-01

People commonly anthropomorphize nonhuman agents, imbuing everything from computers to pets to gods with humanlike capacities and mental experiences. Although widely observed, the determinants of anthropomorphism are poorly understood and rarely investigated. We propose that people anthropomorphize, in part, to satisfy effectance motivation-the basic and chronic motivation to attain mastery of one's environment. Five studies demonstrated that increasing effectance motivation by manipulating the perceived unpredictability of a nonhuman agent or by increasing the incentives for mastery increases anthropomorphism. Neuroimaging data demonstrated that the neural correlates of this process are similar to those engaged when mentalizing other humans. A final study demonstrated that anthropomorphizing a stimulus makes it appear more predictable and understandable, suggesting that anthropomorphism satisfies effectance motivation. Anthropomorphizing nonhuman agents seems to satisfy the basic motivation to make sense of an otherwise uncertain environment. (PsycINFO Database Record (c) 2010 APA, all rights reserved).

29 CFR 4000.53 - May I use electronic media to satisfy PBGC's record retention requirements?

Code of Federal Regulations, 2011 CFR

2011-07-01

... 29 Labor 9 2011-07-01 2011-07-01 false May I use electronic media to satisfy PBGC's record... Electronic Means of Record Retention § 4000.53 May I use electronic media to satisfy PBGC's record retention requirements? General requirements. You may use electronic media to satisfy the record maintenance and...

29 CFR 4000.53 - May I use electronic media to satisfy PBGC's record retention requirements?

Code of Federal Regulations, 2014 CFR

2014-07-01

... 29 Labor 9 2014-07-01 2014-07-01 false May I use electronic media to satisfy PBGC's record... Electronic Means of Record Retention § 4000.53 May I use electronic media to satisfy PBGC's record retention requirements? General requirements. You may use electronic media to satisfy the record maintenance and...

29 CFR 4000.53 - May I use electronic media to satisfy PBGC's record retention requirements?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 29 Labor 9 2010-07-01 2010-07-01 false May I use electronic media to satisfy PBGC's record... Electronic Means of Record Retention § 4000.53 May I use electronic media to satisfy PBGC's record retention requirements? General requirements. You may use electronic media to satisfy the record maintenance and...

29 CFR 4000.53 - May I use electronic media to satisfy PBGC's record retention requirements?

Code of Federal Regulations, 2013 CFR

2013-07-01

... 29 Labor 9 2013-07-01 2013-07-01 false May I use electronic media to satisfy PBGC's record... Electronic Means of Record Retention § 4000.53 May I use electronic media to satisfy PBGC's record retention requirements? General requirements. You may use electronic media to satisfy the record maintenance and...

29 CFR 4000.53 - May I use electronic media to satisfy PBGC's record retention requirements?

Code of Federal Regulations, 2012 CFR

2012-07-01

... 29 Labor 9 2012-07-01 2012-07-01 false May I use electronic media to satisfy PBGC's record... Electronic Means of Record Retention § 4000.53 May I use electronic media to satisfy PBGC's record retention requirements? General requirements. You may use electronic media to satisfy the record maintenance and...

Safe and Secure Services Based on NGN

NASA Astrophysics Data System (ADS)

Fukazawa, Tomoo; Nisase, Takemi; Kawashima, Masahisa; Hariu, Takeo; Oshima, Yoshihito

Next Generation Network (NGN), which has been undergoing standardization as it has developed, is expected to create new services that converge the fixed and mobile networks. This paper introduces the basic requirements for NGN in terms of security and explains the standardization activities, in particular, the requirements for the security function described in Y.2701 discussed in ITU-T SG-13. In addition to the basic NGN security function, requirements for NGN authentication are also described from three aspects: security, deployability, and service. As examples of authentication implementation, three profiles-namely, fixed, nomadic, and mobile-are defined in this paper. That is, the “fixed profile” is typically for fixed-line subscribers, the “nomadic profile” basically utilizes WiFi access points, and the “mobile profile” provides ideal NGN mobility for mobile subscribers. All three of these profiles satisfy the requirements from security aspects. The three profiles are compared from the viewpoint of requirements for deployability and service. After showing that none of the three profiles can fulfill all of the requirements, we propose that multiple profiles should be used by NGN providers. As service and application examples, two promising NGN applications are proposed. The first is a strong authentication mechanism that makes Web applications more safe and secure even against password theft. It is based on NGN ID federation function. The second provides an easy peer-to-peer broadband virtual private network service aimed at safe and secure communication for personal/SOHO (small office, home office) users, based on NGN SIP (session initiation protocol) session control.

Integration of a code for aeroelastic design of conventional and composite wings into ACSYNT, an aircraft synthesis program. [wing aeroelastic design (WADES)

NASA Technical Reports Server (NTRS)

Mullen, J., Jr.

1976-01-01

A comparison of program estimates of wing weight, material distribution. structural loads and elastic deformations with actual Northrop F-5A/B data is presented. Correlation coefficients obtained using data from a number of existing aircraft were computed for use in vehicle synthesis to estimate wing weights. The modifications necessary to adapt the WADES code for use in the ACSYNT program are described. Basic program flow and overlay structure is outlined. An example of the convergence of the procedure in estimating wing weights during the synthesis of a vehicle to satisfy F-5 mission requirements is given. A description of inputs required for use of the WADES program is included.

What can robots tell us about brains? A synthetic approach towards the study of learning and problem solving.

PubMed

Voegtlin, T; Verschure, P F

1999-01-01

This paper argues for the development of synthetic approaches towards the study of brain and behavior as a complement to the more traditional empirical mode of research. As an example we present our own work on learning and problem solving which relates to the behavioral paradigms of classical and operant conditioning. We define the concept of learning in the context of behavior and lay out the basic methodological requirements a model needs to satisfy, which includes evaluations using robots. In addition, we define a number of design principles neuronal models should obey to be considered relevant. We present in detail the construction of a neural model of short- and long-term memory which can be applied to an artificial behaving system. The presented model (DAC4) provides a novel self-consistent implementation of these processes, which satisfies our principles. This model will be interpreted towards the present understanding of the neuronal substrate of memory.

Toward the quantification of a conceptual framework for movement ecology using circular statistical modeling.

PubMed

Shimatani, Ichiro Ken; Yoda, Ken; Katsumata, Nobuhiro; Sato, Katsufumi

2012-01-01

To analyze an animal's movement trajectory, a basic model is required that satisfies the following conditions: the model must have an ecological basis and the parameters used in the model must have ecological interpretations, a broad range of movement patterns can be explained by that model, and equations and probability distributions in the model should be mathematically tractable. Random walk models used in previous studies do not necessarily satisfy these requirements, partly because movement trajectories are often more oriented or tortuous than expected from the models. By improving the modeling for turning angles, this study aims to propose a basic movement model. On the basis of the recently developed circular auto-regressive model, we introduced a new movement model and extended its applicability to capture the asymmetric effects of external factors such as wind. The model was applied to GPS trajectories of a seabird (Calonectris leucomelas) to demonstrate its applicability to various movement patterns and to explain how the model parameters are ecologically interpreted under a general conceptual framework for movement ecology. Although it is based on a simple extension of a generalized linear model to circular variables, the proposed model enables us to evaluate the effects of external factors on movement separately from the animal's internal state. For example, maximum likelihood estimates and model selection suggested that in one homing flight section, the seabird intended to fly toward the island, but misjudged its navigation and was driven off-course by strong winds, while in the subsequent flight section, the seabird reset the focal direction, navigated the flight under strong wind conditions, and succeeded in approaching the island.

Needs Satisfied by Media Use: An Audience Typology.

ERIC Educational Resources Information Center

Kochevar, John J.

A study was conducted to segment the mass media audience on the basis of basic needs and media satisfactions. Two hundred undergraduate journalism students completed lengthy questionnaires rating their media use before and during the New York newspaper strike of 1978, along with their basic needs, media satisfactions, and a variety of other…

Consumption and Subjective Wellbeing: Exploring Basic Needs, Social Comparison, Social Integration and Hedonism in Peru

ERIC Educational Resources Information Center

Guillen-Royo, Monica

2008-01-01

Within material poverty contexts, consumption and subjective wellbeing are positively and strongly related. This is usually explained in terms of the increased possibilities to satisfy basic needs that additional spending provides. Other important aspects of consumption, such as its relative, symbolic and hedonic dimensions are not generally…

AFFECT in the Schools: A Return to the Most Basic of Basics.

ERIC Educational Resources Information Center

Currie, John R.

1988-01-01

Maintains that a child's cognitive growth is greatly enhanced by attending to the level of emotional warmth between teacher and child. But attempts at satisfying affective needs put the educator in a precarious position. An affective program in an elementary school that minimizes such risks is described. (BB)

Coaching for a winning dental team.

PubMed

Schwartz, S

2000-08-15

In 1943, Abraham Maslow, the "father of humanistic psychology," formulated his "Hierarchy of Needs Theory." Maslow proposed people have needs that must be satisfied, and these needs will motivate until they are satisfied. The needs are arranged in a hierarchy or pyramid ranging from basic needs to higher needs with an individual needing to satisfy a lower need before a higher need can motivate. The five needs of the hierarchy are: physiological needs, safety needs, social needs, esteem needs, and self-actualization. This article discusses adaptation of the hierarchy of needs to the dental practice to motivate staff to perform at a higher level.

The role of response force on the persistence and structure of behavior during extinction.

PubMed

Pinkston, Jonathan W; Foss, Erica K

2018-01-01

Behavior Momentum Theory has emerged as a prominent account of resistance to change in both basic and applied research. Although laboratory studies often define precise, repeatable responses, application research often deals with response classes that may vary widely along a number of dimensions. In general, Behavior Momentum Theory has not addressed how response dimensions impact resistance to change, providing an opportunity to expand the model in new directions. Four rats pressed a force transducer under a multiple variable interval (VI) 60-s VI 60-s schedule of reinforcement. In one component, responses satisfied the schedule only if the response force fell within a "low" force band requirement; responses in the other schedule were required to satisfy a "high" force band. Once responding stabilized, extinction was programmed for three sessions. Then, the procedures were replicated. The results showed that response force came under discriminative control, but force requirements had no impact on resistance to extinction. In a follow-up condition, the schedule was changed to a multiple VI 30-s VI 120-s schedule and the low-force band operated in both components. The results showed that behavior maintained by the VI 30-s schedule was generally more resistant to extinction. A secondary analysis showed that force distributions created under baseline maintained during extinction. Overall, the results suggest that differential response force requirements prevailing in steady state do not affect the course of extinction. © 2018 Society for the Experimental Analysis of Behavior.

What is the Final Verification of Engineering Requirements?

NASA Technical Reports Server (NTRS)

Poole, Eric

2010-01-01

This slide presentation reviews the process of development through the final verification of engineering requirements. The definition of the requirements is driven by basic needs, and should be reviewed by both the supplier and the customer. All involved need to agree upon a formal requirements including changes to the original requirements document. After the requirements have ben developed, the engineering team begins to design the system. The final design is reviewed by other organizations. The final operational system must satisfy the original requirements, though many verifications should be performed during the process. The verification methods that are used are test, inspection, analysis and demonstration. The plan for verification should be created once the system requirements are documented. The plan should include assurances that every requirement is formally verified, that the methods and the responsible organizations are specified, and that the plan is reviewed by all parties. The options of having the engineering team involved in all phases of the development as opposed to having some other organization continue the process once the design has been complete is discussed.

The cross-cultural importance of satisfying vital needs.

PubMed

Alvarez, Allen Andrew A

2009-11-01

Ethical beliefs may vary across cultures but there are things that must be valued as preconditions to any cultural practice. Physical and mental abilities vital to believing, valuing and practising a culture are such preconditions and it is always important to protect them. If one is to practise a distinct culture, she must at least have these basic abilities. Access to basic healthcare is one way to ensure that vital abilities are protected. John Rawls argued that access to all-purpose primary goods must be ensured. Amartya Sen and Martha Nussbaum claim that universal capabilities are what resources are meant to enable. Len Doyal and Ian Gough identify physical health and autonomy as basic needs of every person in every culture. When we disagree on what to prioritize, when resources to satisfy competing demands are scarce, our common needs can provide a point of normative convergence. Need-based rationing, however, has been criticized for being too indeterminate to give guidance for deciding which healthcare services to prioritize and for tending to create a bottomless-pit problem. But there is a difference between needing something (first-order need) and needing to have the ability to need (second-order need). Even if we disagree about which first-order need to prioritize, we must accept the importance of satisfying our second-order need to have the ability to value things. We all have a second-order need for basic healthcare as a means to protect our vital abilities even if we differ in what our cultures consider to be particular first-order needs.

Optimal Decision Making in a Class of Uncertain Systems Based on Uncertain Variables

NASA Astrophysics Data System (ADS)

Bubnicki, Z.

2006-06-01

The paper is concerned with a class of uncertain systems described by relational knowledge representations with unknown parameters which are assumed to be values of uncertain variables characterized by a user in the form of certainty distributions. The first part presents the basic optimization problem consisting in finding the decision maximizing the certainty index that the requirement given by a user is satisfied. The main part is devoted to the description of the optimization problem with the given certainty threshold. It is shown how the approach presented in the paper may be applied to some problems for anticipatory systems.

Novel demonstration of the renormalization group invariance of the fixed-order predictions using the principle of maximum conformality and the C -scheme coupling

NASA Astrophysics Data System (ADS)

Wu, Xing-Gang; Shen, Jian-Ming; Du, Bo-Lun; Brodsky, Stanley J.

2018-05-01

As a basic requirement of the renormalization group invariance, any physical observable must be independent of the choice of both the renormalization scheme and the initial renormalization scale. In this paper, we show that by using the newly suggested C -scheme coupling, one can obtain a demonstration that the principle of maximum conformality prediction is scheme-independent to all-orders for any renormalization schemes, thus satisfying all of the conditions of the renormalization group invariance. We illustrate these features for the nonsinglet Adler function and for τ decay to ν + hadrons at the four-loop level.

Frequency control of wind turbine in power system

NASA Astrophysics Data System (ADS)

Xu, Huawei

2018-06-01

In order to improve the stability of the overall frequency of the power system, automatic power generation control and secondary frequency adjustment were applied. Automatic power generation control was introduced into power generation planning. A dual-fed wind generator power regulation model suitable for secondary frequency regulation was established. The results showed that this method satisfied the basic requirements of frequency regulation control of large-scale wind power access power systems and improved the stability and reliability of power system operation. Therefore, this system frequency control method and strategy is relatively simple. The effect is significant. The system frequency can quickly reach a steady state. It is worth applying and promoting.

A Brokering Protocol for Agent-Based Grid Resource Discovery

NASA Astrophysics Data System (ADS)

Kang, Jaeyong; Sim, Kwang Mong

Resource discovery is one of the basic and key aspects in grid resource management, which aims at searching for the suitable resources for satisfying the requirement of users' applications. This paper introduces an agent-based brokering protocol which connects users and providers in grid environments. In particular, it focuses on addressing the problem of connecting users and providers. A connection algorithm that matches advertisements of users and requests from providers based on pre-specified multiple criteria is devised and implemented. The connection algorithm mainly consists of four stages: selection, evaluation, filtering, and recommendation. A series of experiments that were carried out in executing the protocol, and favorable results were obtained.

The X-beam as a deployable boom for the space station

NASA Technical Reports Server (NTRS)

Adams, Louis R.

1988-01-01

Extension of antennas and thrust modules from the primary structure of the space station will require deployable beams of high stiffness and strength, as well as low mass and package volume. A square boom cross section is desirable for interface reasons. These requirements and others are satisfied by the X-beam. The X-beam folds by simple geometry, using single-degree-of-freedom hinges at simple angles, with no strain during deployment. Strut members are of large diameter with unidirectional graphite fibers for maximum beam performance. Fittings are aluminum with phosphor bronze bushings so that compliance is low and joint lifetime is high. The several beam types required for different applications on the space station will use the same basic design, with changes in strut cross section where necessary. Deployment is by a BI-STEM which pushes the beam out; retraction is by cables which cause initial folding and pull the beam in.

Candidate Mission from Planet Earth control and data delivery system architecture

NASA Technical Reports Server (NTRS)

Shapiro, Phillip; Weinstein, Frank C.; Hei, Donald J., Jr.; Todd, Jacqueline

1992-01-01

Using a structured, experienced-based approach, Goddard Space Flight Center (GSFC) has assessed the generic functional requirements for a lunar mission control and data delivery (CDD) system. This analysis was based on lunar mission requirements outlined in GSFC-developed user traffic models. The CDD system will facilitate data transportation among user elements, element operations, and user teams by providing functions such as data management, fault isolation, fault correction, and link acquisition. The CDD system for the lunar missions must not only satisfy lunar requirements but also facilitate and provide early development of data system technologies for Mars. Reuse and evolution of existing data systems can help to maximize system reliability and minimize cost. This paper presents a set of existing and currently planned NASA data systems that provide the basic functionality. Reuse of such systems can have an impact on mission design and significantly reduce CDD and other system development costs.

Coverage Metrics for Requirements-Based Testing: Evaluation of Effectiveness

NASA Technical Reports Server (NTRS)

Staats, Matt; Whalen, Michael W.; Heindahl, Mats P. E.; Rajan, Ajitha

2010-01-01

In black-box testing, the tester creates a set of tests to exercise a system under test without regard to the internal structure of the system. Generally, no objective metric is used to measure the adequacy of black-box tests. In recent work, we have proposed three requirements coverage metrics, allowing testers to objectively measure the adequacy of a black-box test suite with respect to a set of requirements formalized as Linear Temporal Logic (LTL) properties. In this report, we evaluate the effectiveness of these coverage metrics with respect to fault finding. Specifically, we conduct an empirical study to investigate two questions: (1) do test suites satisfying a requirements coverage metric provide better fault finding than randomly generated test suites of approximately the same size?, and (2) do test suites satisfying a more rigorous requirements coverage metric provide better fault finding than test suites satisfying a less rigorous requirements coverage metric? Our results indicate (1) only one coverage metric proposed -- Unique First Cause (UFC) coverage -- is sufficiently rigorous to ensure test suites satisfying the metric outperform randomly generated test suites of similar size and (2) that test suites satisfying more rigorous coverage metrics provide better fault finding than test suites satisfying less rigorous coverage metrics.

[Update on upper eyelid blepharoplasty].

PubMed

Klingenstein, A; Hintschich, C

2018-04-01

Upper eyelid blepharoplasty is among the most frequent oculoplastic surgical procedures. It is often performed as one of the first esthetic surgical interventions by surgeons of various disciplines. While there is a high probability of happy and satisfied patients postoperatively, there are important potential surgical complications that should be prevented. This requires a careful preoperative, perioperative and postoperative approach. This synopsis presents the basic considerations concerning upper eyelid blepharoplasty to serve as practical surgical guidelines. This is a compendium of important preoperative, perioperative and postoperative contemplations derived from the medical literature, expert opinions and the authors' personal experiences. Careful examination and documentation of eyelid and periorbital findings are required in order to identify additional pathologies to dermatochalasis and plan the surgical approach accordingly. There is a trend in the literature and in expert opinions away from large tissue resection and towards volume preserving and volume reconstructing surgical techniques. Correct placement of the skin fold as well as maintaining lid symmetry are crucial points in order to achieve a natural appearance and patient satisfaction. Careful and realistic patient information, state of the art surgery including cautious tissue resection and correct symmetrical formation of the skin fold as well as postoperative assistance and availability increase the likelihood of satisfied patients after blepharoplasty.

34 CFR 75.592 - Federal evaluation-satisfying requirement for grantee evaluation.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 34 Education 1 2010-07-01 2010-07-01 false Federal evaluation-satisfying requirement for grantee evaluation. 75.592 Section 75.592 Education Office of the Secretary, Department of Education DIRECT GRANT PROGRAMS What Conditions Must Be Met by a Grantee? Evaluation § 75.592 Federal evaluation—satisfying...

34 CFR 75.592 - Federal evaluation-satisfying requirement for grantee evaluation.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 34 Education 1 2014-07-01 2014-07-01 false Federal evaluation-satisfying requirement for grantee evaluation. 75.592 Section 75.592 Education Office of the Secretary, Department of Education DIRECT GRANT PROGRAMS What Conditions Must Be Met by a Grantee? Evaluation § 75.592 Federal evaluation—satisfying...

Optimal aeroassisted orbital transfer with plane change using collocation and nonlinear programming

NASA Technical Reports Server (NTRS)

Shi, Yun. Y.; Nelson, R. L.; Young, D. H.

1990-01-01

The fuel optimal control problem arising in the non-planar orbital transfer employing aeroassisted technology is addressed. The mission involves the transfer from high energy orbit (HEO) to low energy orbit (LEO) with orbital plane change. The basic strategy here is to employ a combination of propulsive maneuvers in space and aerodynamic maneuvers in the atmosphere. The basic sequence of events for the aeroassisted HEO to LEO transfer consists of three phases. In the first phase, the orbital transfer begins with a deorbit impulse at HEO which injects the vehicle into an elliptic transfer orbit with perigee inside the atmosphere. In the second phase, the vehicle is optimally controlled by lift and bank angle modulations to perform the desired orbital plane change and to satisfy heating constraints. Because of the energy loss during the turn, an impulse is required to initiate the third phase to boost the vehicle back to the desired LEO orbital altitude. The third impulse is then used to circularize the orbit at LEO. The problem is solved by a direct optimization technique which uses piecewise polynomial representation for the state and control variables and collocation to satisfy the differential equations. This technique converts the optimal control problem into a nonlinear programming problem which is solved numerically. Solutions were obtained for cases with and without heat constraints and for cases of different orbital inclination changes. The method appears to be more powerful and robust than other optimization methods. In addition, the method can handle complex dynamical constraints.

25 CFR 531.1 - Required provisions.

Code of Federal Regulations, 2010 CFR

2010-04-01

...) years if the Chairman is satisfied that the capital investment required, and the income projections, for... satisfied that the capital investment required and income projections for the gaming operation require the... the gaming facility; (2) Providing operating capital; (3) Establishing operating days and hours; (4...

Student scientific inquiry in the core curriculum.

PubMed

Vaidean, Georgeta D; Vansal, Sandeep S; Moore, Ronnie J; Feldman, Stuart

2013-10-14

To design and implement a required student-driven research program as a capstone experience in the doctor of pharmacy (PharmD) curriculum. A research proposal in the form of a competitive grant application was required for each of 65 fourth-year students in an inaugural PharmD class at Touro College of Pharmacy in New York. The focus of the proposals was on hypothesis-driven research in basic science, clinical research, health outcomes, and public health. Students' research proposals were graded using a standardized grading instrument. On a post-experience survey, most students rated the overall experience positively, indicating increased confidence in their research skills. About two-thirds of faculty members were satisfied with their students' performance, and the great majority thought the experience would be useful in the students' careers. The capstone research project was a positive experience for fourth-year students.

The Frölicher-type inequalities of foliations

NASA Astrophysics Data System (ADS)

Raźny, Paweł

2017-04-01

The purpose of this article is to adapt the Frölicher-type inequality, stated and proven for complex and symplectic manifolds in Angella and Tomassini (2015), to the case of transversely holomorphic and symplectic foliations. These inequalities provide a criterion for checking whether a foliation transversely satisfies the ∂ ∂ ¯ -lemma and the ddΛ-lemma (i.e. whether the basic forms of a given foliation satisfy them). These lemmas are linked to such properties as the formality of the basic de Rham complex of a foliation and the transverse hard Lefschetz property. In particular they provide an obstruction to the existence of a transverse Kähler structure for a given foliation. In the second section we will provide some information concerning the d‧d″-lemma for a given double complex (K • , • ,d‧ ,d″) and state the main results from Angella and Tomassini (2015). We will also recall some basic facts and definitions concerning foliations. In the third section we treat the case of transversely holomorphic foliations. We also give a brief review of some properties of the basic Bott-Chern and Aeppli cohomology theories. In Section 4 we prove the symplectic version of the Frölicher-type inequality. The final 3 sections of this paper are devoted to the applications of our main theorems. In them we verify the aforementioned lemmas for some simple examples, give the orbifold versions of the Frölicher-type inequalities and show that transversely Kähler foliations satisfy both the ∂ ∂ ¯ -lemma and the ddΛ-lemma (or in other words that our main theorems provide an obstruction to the existence of a transversely Kähler structure).

Representation of natural numbers in quantum mechanics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Benioff, Paul

2001-03-01

This paper represents one approach to making explicit some of the assumptions and conditions implied in the widespread representation of numbers by composite quantum systems. Any nonempty set and associated operations is a set of natural numbers or a model of arithmetic if the set and operations satisfy the axioms of number theory or arithmetic. This paper is limited to k-ary representations of length L and to the axioms for arithmetic modulo k{sup L}. A model of the axioms is described based on an abstract L-fold tensor product Hilbert space H{sup arith}. Unitary maps of this space onto a physicalmore » parameter based product space H{sup phy} are then described. Each of these maps makes states in H{sup phy}, and the induced operators, a model of the axioms. Consequences of the existence of many of these maps are discussed along with the dependence of Grover's and Shor's algorithms on these maps. The importance of the main physical requirement, that the basic arithmetic operations are efficiently implementable, is discussed. This condition states that there exist physically realizable Hamiltonians that can implement the basic arithmetic operations and that the space-time and thermodynamic resources required are polynomial in L.« less

Stowable Energy-Absorbing Rocker-Bogie Suspensions

NASA Technical Reports Server (NTRS)

Harrington, Brian; Voorhees, Christopher

2007-01-01

A report discusses the design of the rocker-bogie suspensions of the Mars Exploration Rover vehicles, which were landed on Mars in January 2004. Going beyond the basic requirements regarding mobility on uneven terrain, the design had to satisfy requirements (1) to enable each suspension to contort so that the rover could be stowed within limited space in a tetrahedral lander prior to deployment and (2) that the suspension be able to absorb appreciable impact loads, with limited deflection, during egress from the lander and traversal of terrain. For stowability, six joints (three on the right, three on the left) were added to the basic rocker-bogie mechanism. One of the joints on each side was a yoke-and-clevis joint at the suspension/differential interface, one was a motorized twist joint in the forward portion of the rocker, and one was a linear joint created by modifying a fixed-length bogie member into a telescoping member. For absorption of impact, the structural members were in the form of box beams made by electron-beam welding of machined, thin-walled, C-channel, titanium components. The box beams were very lightweight and could withstand high bending and torsional loads.

Developing the plan

NASA Technical Reports Server (NTRS)

1975-01-01

The basic sequence in the planning development process is discussed. Alternative ways of satisfying estimated needs, and the selection of an alternative are described along with the development of a plan to implement the selected alternative.

Development and Initial Validation of a Measure of Autonomy, Competence, and Relatedness in Exercise: The Basic Psychological Needs in Exercise Scale

ERIC Educational Resources Information Center

Vlachopoulos, Symeon P.; Michailidou, Sotiria

2006-01-01

The development process and initial validation of the Basic Psychological Needs in Exercise Scale (BPNES) are presented in this study. The BPNES is a domain-specific self-report instrument designed to assess perceptions of the extent to which the innate needs for autonomy, competence, and relatedness (Deci & Ryan, 2000) are satisfied in…

Nonadditive entropies yield probability distributions with biases not warranted by the data.

PubMed

Pressé, Steve; Ghosh, Kingshuk; Lee, Julian; Dill, Ken A

2013-11-01

Different quantities that go by the name of entropy are used in variational principles to infer probability distributions from limited data. Shore and Johnson showed that maximizing the Boltzmann-Gibbs form of the entropy ensures that probability distributions inferred satisfy the multiplication rule of probability for independent events in the absence of data coupling such events. Other types of entropies that violate the Shore and Johnson axioms, including nonadditive entropies such as the Tsallis entropy, violate this basic consistency requirement. Here we use the axiomatic framework of Shore and Johnson to show how such nonadditive entropy functions generate biases in probability distributions that are not warranted by the underlying data.

I'll Tell You What You Think: An Exercise in Pseudoscience Debunking in an Introductory Astronomy Course

NASA Astrophysics Data System (ADS)

Caton, Dan

2013-11-01

At Appalachian State University students have to take just two semesters of a physical or biological science to satisfy the general education requirements. Most non-science major students have little time in their crowded schedules to take additional science courses, whether they want to or not, and in fact face a surcharge when taking more courses than needed to graduate. Given this environment, it is essential that we cover more than just the basics of one particular discipline, like astronomy in my case. We should teach something about the overall philosophy of science, the scientific method, and the importance of science in our lives.

Tropical Rainfall Measuring Mission (TRMM) project. VI - Spacecraft, scientific instruments, and launching rocket. Part 4 - TRMM rain radar

NASA Technical Reports Server (NTRS)

Meneghini, Robert; Atlas, David; Awaka, Jun; Okamoto, Ken'ichi; Ihara, Toshio; Nakamura, Kenji; Kozu, Toshiaki; Manabe, Takeshi

1990-01-01

The basic system parameters for the Tropical Rainfall Measuring Mission (TRMM) radar system are frequency, beamwidth, scan angle, resolution, number of independent samples, pulse repetition frequency, data rate, and so on. These parameters were chosen to satisfy NASA's mission requirements. Six candidates for the TRMM rain radar were studied. The study considered three major competitive items: (1) a pulse-compression radar vs. a conventional radar; (2) an active-array radar with a solid state power amplifier vs. a passive-array radar with a traveling-wave-tube amplifier; and (3) antenna types (planar-array antenna vs. cylindrical parabolic antenna). Basic system parameters such as radar sensitivities, power consumption, weight, and size of these six types are described. Trade-off studies of these cases show that the non-pulse-compression active-array radar with a planar array is considered to be the most suitable candidate for the TRMM rain radar at 13.8 GHz.

FY16 ASME High Temperature Code Activities

DOE Office of Scientific and Technical Information (OSTI.GOV)

Swindeman, M. J.; Jetter, R. I.; Sham, T. -L.

2016-09-01

One of the objectives of the ASME high temperature Code activities is to develop and validate both improvements and the basic features of Section III, Division 5, Subsection HB, Subpart B (HBB). The overall scope of this task is to develop a computer program to be used to assess whether or not a specific component under specified loading conditions will satisfy the elevated temperature design requirements for Class A components in Section III, Division 5, Subsection HB, Subpart B (HBB). There are many features and alternative paths of varying complexity in HBB. The initial focus of this task is amore » basic path through the various options for a single reference material, 316H stainless steel. However, the program will be structured for eventual incorporation all the features and permitted materials of HBB. Since this task has recently been initiated, this report focuses on the description of the initial path forward and an overall description of the approach to computer program development.« less

Minimal modeling of the extratropical general circulation

NASA Technical Reports Server (NTRS)

O'Brien, Enda; Branscome, Lee E.

1989-01-01

The ability of low-order, two-layer models to reproduce basic features of the mid-latitude general circulation is investigated. Changes in model behavior with increased spectral resolution are examined in detail. Qualitatively correct time-mean heat and momentum balances are achieved in a beta-plane channel model which includes the first and third meridional modes. This minimal resolution also reproduces qualitatively realistic surface and upper-level winds and mean meridional circulations. Higher meridional resolution does not result in substantial changes in the latitudinal structure of the circulation. A qualitatively correct kinetic energy spectrum is produced when the resolution is high enough to include several linearly stable modes. A model with three zonal waves and the first three meridional modes has a reasonable energy spectrum and energy conversion cycle, while also satisfying heat and momentum budget requirements. This truncation reproduces the basic mechanisms and zonal circulation features that are obtained at higher resolution. The model performance improves gradually with higher resolution and is smoothly dependent on changes in external parameters.

39 Questionable Assumptions in Modern Physics

NASA Astrophysics Data System (ADS)

Volk, Greg

2009-03-01

The growing body of anomalies in new energy, low energy nuclear reactions, astrophysics, atomic physics, and entanglement, combined with the failure of the Standard Model and string theory to predict many of the most basic fundamental phenomena, all point to a need for major new paradigms. Not Band-Aids, but revolutionary new ways of conceptualizing physics, in the spirit of Thomas Kuhn's The Structure of Scientific Revolutions. This paper identifies a number of long-held, but unproven assumptions currently being challenged by an increasing number of alternative scientists. Two common themes, both with venerable histories, keep recurring in the many alternative theories being proposed: (1) Mach's Principle, and (2) toroidal, vortex particles. Matter-based Mach's Principle differs from both space-based universal frames and observer-based Einsteinian relativity. Toroidal particles, in addition to explaining electron spin and the fundamental constants, satisfy the basic requirement of Gauss's misunderstood B Law, that motion itself circulates. Though a comprehensive theory is beyond the scope of this paper, it will suggest alternatives to the long list of assumptions in context.

Student Scientific Inquiry in the Core Curriculum

PubMed Central

Vansal, Sandeep S.; Moore, Ronnie J.; Feldman, Stuart

2013-01-01

Objective. To design and implement a required student-driven research program as a capstone experience in the doctor of pharmacy (PharmD) curriculum. Design. A research proposal in the form of a competitive grant application was required for each of 65 fourth-year students in an inaugural PharmD class at Touro College of Pharmacy in New York. The focus of the proposals was on hypothesis-driven research in basic science, clinical research, health outcomes, and public health. Assessment. Students’ research proposals were graded using a standardized grading instrument. On a post-experience survey, most students rated the overall experience positively, indicating increased confidence in their research skills. About two-thirds of faculty members were satisfied with their students’ performance, and the great majority thought the experience would be useful in the students’ careers. Conclusion. The capstone research project was a positive experience for fourth-year students. PMID:24159217

A telescopic jib for continuous adjustment

NASA Technical Reports Server (NTRS)

Etzler, C. C.

1979-01-01

For special space applications, e.g. for experiments distant from any orbital platforms or manipulators a new kind of jibs with extreme extension capacity has to be designed. Considering the requirements, the telescopic principle is found to be the most promising. For the choice of the stiff structure, design criteria are evaluated. Special effort deals with the drive system. An electromechanical system can satisfy the requirements. First results of the development of such a drive are presented. The most significant features are: A telescopic assembly of tubes which can be mutually moved by a short spindle in the center of the package. An elastically suspended screw is located at the bottom of each tube. For the jib extension, these screws will be linked with the spindle. The control of their sequence and the adjustment of tubes in mutual end positions are performed by latches. A functional model proved the basic idea.

Earth resources mission performance studies. Volume 2: Simulation results

NASA Technical Reports Server (NTRS)

1974-01-01

Simulations were made at three month intervals to investigate the EOS mission performance over the four seasons of the year. The basic objectives of the study were: (1) to evaluate the ability of an EOS type system to meet a representative set of specific collection requirements, and (2) to understand the capabilities and limitations of the EOS that influence the system's ability to satisfy certain collection objectives. Although the results were obtained from a consideration of a two sensor EOS system, the analysis can be applied to any remote sensing system having similar optical and operational characteristics. While the category related results are applicable only to the specified requirement configuration, the results relating to general capability and limitations of the sensors can be applied in extrapolating to other U.S. based EOS collection requirements. The TRW general purpose mission simulator and analytic techniques discussed in this report can be applied to a wide range of collection and planning problems of earth orbiting imaging systems.

Propellant injection systems and processes

NASA Technical Reports Server (NTRS)

Ito, Jackson I.

1995-01-01

The previous 'Art of Injector Design' is maturing and merging with the more systematic 'Science of Combustion Device Analysis.' This technology can be based upon observation, correlation, experimentation and ultimately analytical modeling based upon basic engineering principles. This methodology is more systematic and far superior to the historical injector design process of 'Trial and Error' or blindly 'Copying Past Successes.' The benefit of such an approach is to be able to rank candidate design concepts for relative probability of success or technical risk in all the important combustion device design requirements and combustion process development risk categories before committing to an engine development program. Even if a single analytical design concept cannot be developed to predict satisfying all requirements simultaneously, a series of risk mitigation key enabling technologies can be identified for early resolution. Lower cost subscale or laboratory experimentation to demonstrate proof of principle, critical instrumentation requirements, and design discriminating test plans can be developed based on the physical insight provided by these analyses.

Monkeys choose as if maximizing utility compatible with basic principles of revealed preference theory

PubMed Central

Pastor-Bernier, Alexandre; Plott, Charles R.; Schultz, Wolfram

2017-01-01

Revealed preference theory provides axiomatic tools for assessing whether individuals make observable choices “as if” they are maximizing an underlying utility function. The theory evokes a tradeoff between goods whereby individuals improve themselves by trading one good for another good to obtain the best combination. Preferences revealed in these choices are modeled as curves of equal choice (indifference curves) and reflect an underlying process of optimization. These notions have far-reaching applications in consumer choice theory and impact the welfare of human and animal populations. However, they lack the empirical implementation in animals that would be required to establish a common biological basis. In a design using basic features of revealed preference theory, we measured in rhesus monkeys the frequency of repeated choices between bundles of two liquids. For various liquids, the animals’ choices were compatible with the notion of giving up a quantity of one good to gain one unit of another good while maintaining choice indifference, thereby implementing the concept of marginal rate of substitution. The indifference maps consisted of nonoverlapping, linear, convex, and occasionally concave curves with typically negative, but also sometimes positive, slopes depending on bundle composition. Out-of-sample predictions using homothetic polynomials validated the indifference curves. The animals’ preferences were internally consistent in satisfying transitivity. Change of option set size demonstrated choice optimality and satisfied the Weak Axiom of Revealed Preference (WARP). These data are consistent with a version of revealed preference theory in which preferences are stochastic; the monkeys behaved “as if” they had well-structured preferences and maximized utility. PMID:28202727

Monkeys choose as if maximizing utility compatible with basic principles of revealed preference theory.

PubMed

Pastor-Bernier, Alexandre; Plott, Charles R; Schultz, Wolfram

2017-03-07

Revealed preference theory provides axiomatic tools for assessing whether individuals make observable choices "as if" they are maximizing an underlying utility function. The theory evokes a tradeoff between goods whereby individuals improve themselves by trading one good for another good to obtain the best combination. Preferences revealed in these choices are modeled as curves of equal choice (indifference curves) and reflect an underlying process of optimization. These notions have far-reaching applications in consumer choice theory and impact the welfare of human and animal populations. However, they lack the empirical implementation in animals that would be required to establish a common biological basis. In a design using basic features of revealed preference theory, we measured in rhesus monkeys the frequency of repeated choices between bundles of two liquids. For various liquids, the animals' choices were compatible with the notion of giving up a quantity of one good to gain one unit of another good while maintaining choice indifference, thereby implementing the concept of marginal rate of substitution. The indifference maps consisted of nonoverlapping, linear, convex, and occasionally concave curves with typically negative, but also sometimes positive, slopes depending on bundle composition. Out-of-sample predictions using homothetic polynomials validated the indifference curves. The animals' preferences were internally consistent in satisfying transitivity. Change of option set size demonstrated choice optimality and satisfied the Weak Axiom of Revealed Preference (WARP). These data are consistent with a version of revealed preference theory in which preferences are stochastic; the monkeys behaved "as if" they had well-structured preferences and maximized utility.

The Postmodernism of David Antin's "Tuning."

ERIC Educational Resources Information Center

Altieri, Charles

1986-01-01

Shows that Antin's talk poems satisfy basic needs. Discusses Antin's view on an art that addresses the concerns of "common life" and concentrates on feelings that do not depend on elaborate and evasively self-sustaining formal constructs. (EL)

Enterprise Pattern: integrating the business process into a unified enterprise model of modern service company

NASA Astrophysics Data System (ADS)

Li, Ying; Luo, Zhiling; Yin, Jianwei; Xu, Lida; Yin, Yuyu; Wu, Zhaohui

2017-01-01

Modern service company (MSC), the enterprise involving special domains, such as the financial industry, information service industry and technology development industry, depends heavily on information technology. Modelling of such enterprise has attracted much research attention because it promises to help enterprise managers to analyse basic business strategies (e.g. the pricing strategy) and even optimise the business process (BP) to gain benefits. While the existing models proposed by economists cover the economic elements, they fail to address the basic BP and its relationship with the economic characteristics. Those proposed in computer science regardless of achieving great success in BP modelling perform poorly in supporting the economic analysis. Therefore, the existing approaches fail to satisfy the requirement of enterprise modelling for MSC, which demands simultaneous consideration of both economic analysing and business processing. In this article, we provide a unified enterprise modelling approach named Enterprise Pattern (EP) which bridges the gap between the BP model and the enterprise economic model of MSC. Proposing a language named Enterprise Pattern Description Language (EPDL) covering all the basic language elements of EP, we formulate the language syntaxes and two basic extraction rules assisting economic analysis. Furthermore, we extend Business Process Model and Notation (BPMN) to support EPDL, named BPMN for Enterprise Pattern (BPMN4EP). The example of mobile application platform is studied in detail for a better understanding of EPDL.

Configuration evaluation and criteria plan. Volume 2: Evaluation critera plan (preliminary). Space Transportation Main Engine (STME) configuration study

NASA Technical Reports Server (NTRS)

Bair, E. K.

1986-01-01

The unbiased selection of the Space Transportation Main Engine (STME) configuration requires that the candidate engines be evaluated against a predetermined set of criteria which must be properly weighted to emphasize critical requirements defined prior to the actual evaluation. The evaluation and selection process involves the following functions: (1) determining if a configuration can satisfy basic STME requirements (yes/no); (2) defining the evaluation criteria; (3) selecting the criteria relative importance or weighting; (4) determining the weighting sensitivities; and (5) establishing a baseline for engine evaluation. The criteria weighting and sensitivities are cost related and are based on mission models and vehicle requirements. The evaluation process is used as a coarse screen to determine the candidate engines for the parametric studies and as a fine screen to determine concept(s) for conceptual design. The criteria used for the coarse and fine screen evaluation process is shown. The coarse screen process involves verifying that the candidate engines can meet the yes/no screening requirements and a semi-subjective quantitative evaluation. The fine screen engines have to meet all of the yes/no screening gates and are then subjected to a detailed evaluation or assessment using the quantitative cost evaluation processes. The option exists for re-cycling a concept through the quantitative portion of the screening and allows for some degree of optimization. The basic vehicle is a two stage LOX/HC, LOX/LH2 parallel burn vehicle capable of placing 150,000 lbs in low Earth orbit (LEO).

Optimization of structures to satisfy aeroelastic requirements

NASA Technical Reports Server (NTRS)

Rudisill, C. S.

1975-01-01

A method for the optimization of structures to satisfy flutter velocity constraints is presented along with a method for determining the flutter velocity. A method for the optimization of structures to satisfy divergence velocity constraints is included.

Mathematic modeling of the Earth's surface and the process of remote sensing

NASA Technical Reports Server (NTRS)

Balter, B. M.

1979-01-01

It is shown that real data from remote sensing of the Earth from outer space are not best suited to the search for optimal procedures with which to process such data. To work out the procedures, it was proposed that data synthesized with the help of mathematical modeling be used. A criterion for simularity to reality was formulated. The basic principles for constructing methods for modeling the data from remote sensing are recommended. A concrete method is formulated for modeling a complete cycle of radiation transformations in remote sensing. A computer program is described which realizes the proposed method. Some results from calculations are presented which show that the method satisfies the requirements imposed on it.

An Improved Suite of Object Oriented Software Measures

NASA Technical Reports Server (NTRS)

Neal, Ralph D.; Weistroffer, H. Roland; Coppins, Richard J.

1997-01-01

In the pursuit of ever increasing productivity, the need to be able to measure specific aspects of software is generally agreed upon. As object oriented programming languages are becoming more and more widely used, metrics specifically designed for object oriented software are required. In recent years there has been an explosion of new, object oriented software metrics proposed in the literature. Unfortunately, many or most of these proposed metrics have not been validated to measure what they claim to measure. In fact, an analysis of many of these metrics shows that they do not satisfy basic properties of measurement theory, and thus their application has to be suspect. In this paper ten improved metrics are proposed and are validated using measurement theory.

SARS: Safeguards Accounting and Reporting Software

NASA Astrophysics Data System (ADS)

Mohammedi, B.; Saadi, S.; Ait-Mohamed, S.

In order to satisfy the requirements of the SSAC (State System for Accounting and Control of nuclear materials), for recording and reporting objectives; this computer program comes to bridge the gape between nuclear facilities operators and national inspection verifying records and delivering reports. The SARS maintains and generates at-facility safeguards accounting records and generates International Atomic Energy Agency (IAEA) safeguards reports based on accounting data input by the user at any nuclear facility. A database structure is built and BORLAND DELPHI programming language has been used. The software is designed to be user-friendly, to make extensive and flexible management of menus and graphs. SARS functions include basic physical inventory tacking, transaction histories and reporting. Access controls are made by different passwords.

Graduate Education in Psychology: A Comment on Rogers' Passionate Statement

ERIC Educational Resources Information Center

Brown, Robert C., Jr.; Tedeschi, James T.

1972-01-01

Authors' hope that this critical evaluation can place Carl Rogers' assumptions into perspective; they propose a compromise program meant to satisfy the basic aims of a humanistic psychology program. For Rogers' rejoinder see AA 512 869. (MB)

A Variational Assimilation Method for Satellite and Conventional Data: Development of Basic Model for Diagnosis of Cyclone Systems

NASA Technical Reports Server (NTRS)

Achtemeier, Gary L.; Scott, Robert W.; Chen, J.

1991-01-01

A summary is presented of the progress toward the completion of a comprehensive diagnostic objective analysis system based upon the calculus of variations. The approach was to first develop the objective analysis subject to the constraints that the final product satisfies the five basic primitive equations for a dry inviscid atmosphere: the two nonlinear horizontal momentum equations, the continuity equation, the hydrostatic equation, and the thermodynamic equation. Then, having derived the basic model, there would be added to it the equations for moist atmospheric processes and the radiative transfer equation.

Integrated design and management of complex and fast track projects

NASA Astrophysics Data System (ADS)

Mancini, Dario

2003-02-01

Modern scientific and technological projects are increasingly in competition over scientific aims, technological innovation, performance, time and cost. They require a dedicated and innovative organization able to satisfy contemporarily various technical and logistic constraints imposed by the final user, and guarantee the satisfaction of technical specifications, identified on the basis of scientific aims. In order to satisfy all the above, the management has to be strategically innovative and intuitive, by removing, first of all, the bottlenecks that are pointed out, usually only at the end of the projects, as the causes of general dissatisfaction. More than 30 years spent working on complex multidisciplinary systems and 20 years of formative experience in managing contemporarily both scientific, technological and industrial projects have given the author the possibility to study, test and validate strategies for parallel project management and integrated design, merged in a sort of unique optimized task, using the newly-coined word "Technomethodology". The paper highlights useful information to be taken into consideration during project organization to minimize the program deviations from the expected goals and describe some of the basic meanings of this new advanced method that is the key for parallel successful management of multiple and interdisciplinary activities.

Inventory of thermal springs and wells within a one-mile radius of Yucca Lodge, Truth or Consequences, New Mexico

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schwab, G.E.

1982-02-01

Equity Management Corporation proposes (1) to build about 30 condominiums at the present site of the Yucca Lodge, Truth or Consequences, New Mexico and (2) to heat the condominiums with the natural thermal waters that discharge from the property. To do so the corporation must satisfy the rules and regulations of four state and federal agencies. To satisfy some of the data requirements of these agencies and to provide basic data on the geohydrology of the area this report provides the results of a field inventory of the springs and wells within one mile of the lodge. Table 1 summarizesmore » the data for eight springs and three sites where springs once issued. Table 2 summarizes the data on forty-four operable wells and thirty wells that are unusable in their present condition. Appendices list (1) wells presumed to be in the area but not located during field inspection and (2) wells that could be in the area, but were found to be beyond the one-mile radius. Temperature and specific conductance of the water show only minor variation within the recognized hot-water.« less

[Analysis of informed consent readibility in intensive care].

PubMed

Ramírez-Puerta, M R; Fernández-Fernández, R; Frías-Pareja, J C; Yuste-Ossorio, M E; Narbona-Galdó, S; Peñas-Maldonado, L

2013-11-01

To analyze the readability of informed consent documents (IC) used in an intensive care department and in the Andalusian Healthcare System (AHS). A descriptive study was carried out. The Intensive Care Unit of a tertiary Hospital, and the AHS. A review and analysis was made of the existing 14 IC models in the Intensive Care Unit and of another 14 IC models offered by the AHS, using the following readability scores: Flesch, Sentence complexity, LEGIN, Fernández-Huerta, Szigriszt and INFLESZ. Twenty-four IC (85.7%) failed to satisfy some of the indexes, while three (10.7%) did not satisfy any of them. Four documents (14.3%) satisfied all the indexes analyzed, and therefore are easy to understand. Flesch score: satisfied by one of the ICU IC (7.1%) and by three of the AHS documents (21.4%). Sentence complexity score: satisfied by 11 of the ICU IC (78.6%) and by 13 of the AHS documents (92.8%). Fernández-Huerta score: satisfied by four of the ICU IC (28.6%) and by 13 of the AHS documents (92.8%). Szigriszt score: satisfied by two of the ICU IC (14.3%) and by 11 of the AHS documents (64.3%). INFLESZ score: satisfied by two of the ICU IC (14.3%) and by 10 of the AHS documents (71.4%). The documents analyzed are generally difficult to read and understand by most people, and do not satisfy the basic purpose for which they were drafted. Copyright © 2012 Elsevier España, S.L. and SEMICYUC. All rights reserved.

14 CFR Appendix E to Part 417 - Flight Termination System Testing and Analysis

Code of Federal Regulations, 2012 CFR

2012-01-01

... contains requirements for tests and analyses that apply to all flight termination systems and the... termination system components that satisfy the requirements of this appendix. (b) Component tests and analyses. A component must satisfy each test or analysis required by any table of this appendix to demonstrate...

14 CFR Appendix E to Part 417 - Flight Termination System Testing and Analysis

Code of Federal Regulations, 2010 CFR

2010-01-01

... contains requirements for tests and analyses that apply to all flight termination systems and the... termination system components that satisfy the requirements of this appendix. (b) Component tests and analyses. A component must satisfy each test or analysis required by any table of this appendix to demonstrate...

14 CFR Appendix E to Part 417 - Flight Termination System Testing and Analysis

Code of Federal Regulations, 2013 CFR

2013-01-01

... contains requirements for tests and analyses that apply to all flight termination systems and the... termination system components that satisfy the requirements of this appendix. (b) Component tests and analyses. A component must satisfy each test or analysis required by any table of this appendix to demonstrate...

14 CFR Appendix E to Part 417 - Flight Termination System Testing and Analysis

Code of Federal Regulations, 2014 CFR

2014-01-01

... contains requirements for tests and analyses that apply to all flight termination systems and the... termination system components that satisfy the requirements of this appendix. (b) Component tests and analyses. A component must satisfy each test or analysis required by any table of this appendix to demonstrate...

14 CFR Appendix E to Part 417 - Flight Termination System Testing and Analysis

Code of Federal Regulations, 2011 CFR

2011-01-01

... contains requirements for tests and analyses that apply to all flight termination systems and the... termination system components that satisfy the requirements of this appendix. (b) Component tests and analyses. A component must satisfy each test or analysis required by any table of this appendix to demonstrate...

78 FR 20999 - Self-Regulatory Organizations; The Depository Trust Company; Notice of Filing of Proposed Rule...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-04-08

... Fund Deposit does not already satisfy the new requirement.\\8\\ \\4\\ See DTC Rules ( http://dtcc.com/legal... Participants Fund Deposit does not already satisfy the new requirement) be deposited with DTC on the same... Regarding the Collection of Participants' Required Participants Fund Deposits April 2, 2013. Pursuant to...

26 CFR 1.410(b)-1 - Minimum coverage requirements (before 1994).

Code of Federal Regulations, 2013 CFR

2013-04-01

... plan satisfies section 410(b)(1) if it satisfies the requirements of paragraph (b)(1) or (b)(2) of this... this subparagraph if it benefits— (i) Seventy percent or more of all employees, or (ii) Eighty percent... requirements of section 410(b)(1) and this subparagraph if it benefits such employees as qualify under a...

Networked buffering: a basic mechanism for distributed robustness in complex adaptive systems.

PubMed

Whitacre, James M; Bender, Axel

2010-06-15

A generic mechanism--networked buffering--is proposed for the generation of robust traits in complex systems. It requires two basic conditions to be satisfied: 1) agents are versatile enough to perform more than one single functional role within a system and 2) agents are degenerate, i.e. there exists partial overlap in the functional capabilities of agents. Given these prerequisites, degenerate systems can readily produce a distributed systemic response to local perturbations. Reciprocally, excess resources related to a single function can indirectly support multiple unrelated functions within a degenerate system. In models of genome:proteome mappings for which localized decision-making and modularity of genetic functions are assumed, we verify that such distributed compensatory effects cause enhanced robustness of system traits. The conditions needed for networked buffering to occur are neither demanding nor rare, supporting the conjecture that degeneracy may fundamentally underpin distributed robustness within several biotic and abiotic systems. For instance, networked buffering offers new insights into systems engineering and planning activities that occur under high uncertainty. It may also help explain recent developments in understanding the origins of resilience within complex ecosystems.

Light harvesting proteins for solar fuel generation in bioengineered photoelectrochemical cells.

PubMed

Ihssen, Julian; Braun, Artur; Faccio, Greta; Gajda-Schrantz, Krisztina; Thöny-Meyer, Linda

2014-01-01

The sun is the primary energy source of our planet and potentially can supply all societies with more than just their basic energy needs. Demand of electric energy can be satisfied with photovoltaics, however the global demand for fuels is even higher. The direct way to produce the solar fuel hydrogen is by water splitting in photoelectrochemical (PEC) cells, an artificial mimic of photosynthesis. There is currently strong resurging interest for solar fuels produced by PEC cells, but some fundamental technological problems need to be solved to make PEC water splitting an economic, competitive alternative. One of the problems is to provide a low cost, high performing water oxidizing and oxygen evolving photoanode in an environmentally benign setting. Hematite, α-Fe2O3, satisfies many requirements for a good PEC photoanode, but its efficiency is insufficient in its pristine form. A promising strategy for enhancing photocurrent density takes advantage of photosynthetic proteins. In this paper we give an overview of how electrode surfaces in general and hematite photoanodes in particular can be functionalized with light harvesting proteins. Specifically, we demonstrate how low-cost biomaterials such as cyanobacterial phycocyanin and enzymatically produced melanin increase the overall performance of virtually no-cost metal oxide photoanodes in a PEC system. The implementation of biomaterials changes the overall nature of the photoanode assembly in a way that aggressive alkaline electrolytes such as concentrated KOH are not required anymore. Rather, a more environmentally benign and pH neutral electrolyte can be used.

Necessary conditions for morally responsible animal research.

PubMed

DeGrazia, David; Sebo, Jeff

2015-10-01

In this article, we present three necessary conditions for morally responsible animal research that we believe people on both sides of this debate can accept. Specifically, we argue that, even if human beings have higher moral status than nonhuman animals, animal research is morally permissible only if it satisfies (1) an expectation of sufficient net benefit, (2) a worthwhile-life condition, and (3) a no-unnecessary-harm/qualified-basic-needs condition. We then claim that, whether or not these necessary conditions are jointly sufficient for justified animal research, they are relatively demanding, with the consequence that many animal experiments may fail to satisfy them.

Accuracy analysis of pointing control system of solar power station

NASA Technical Reports Server (NTRS)

Hung, J. C.; Peebles, P. Z., Jr.

1978-01-01

The first-phase effort concentrated on defining the minimum basic functions that the retrodirective array must perform, identifying circuits that are capable of satisfying the basic functions, and looking at some of the error sources in the system and how they affect accuracy. The initial effort also examined three methods for generating torques for mechanical antenna control, performed a rough analysis of the flexible body characteristics of the solar collector, and defined a control system configuration for mechanical pointing control of the array.

48 CFR 6.302-1 - Only one responsible source and no other supplies or services will satisfy agency requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... REQUIREMENTS Other Than Full and Open Competition 6.302-1 Only one responsible source and no other supplies or... sources, and no other type of supplies or services will satisfy agency requirements, full and open... capabilities. (2) The existence of limited rights in data, patent rights, copyrights, or secret processes; the...

17 CFR 240.14d-1 - Scope of and definitions applicable to Regulations 14D and 14E.

Code of Federal Regulations, 2012 CFR

2012-04-01

... its aggregate trading volume on securities exchanges in Canada and on the Canadian Dealing Network... accordance with the requirements of the home jurisdiction law or practice will satisfy the requirements of... jurisdiction law or practice will satisfy the requirements of § 240.14e-1(c). Where payment may not be made on...

17 CFR 240.14d-1 - Scope of and definitions applicable to Regulations 14D and 14E.

Code of Federal Regulations, 2011 CFR

2011-04-01

... its aggregate trading volume on securities exchanges in Canada and on the Canadian Dealing Network... accordance with the requirements of the home jurisdiction law or practice will satisfy the requirements of... jurisdiction law or practice will satisfy the requirements of § 240.14e-1(c). Where payment may not be made on...

17 CFR 240.14d-1 - Scope of and definitions applicable to Regulations 14D and 14E.

Code of Federal Regulations, 2013 CFR

2013-04-01

... its aggregate trading volume on securities exchanges in Canada and on the Canadian Dealing Network... accordance with the requirements of the home jurisdiction law or practice will satisfy the requirements of... jurisdiction law or practice will satisfy the requirements of § 240.14e-1(c). Where payment may not be made on...

17 CFR 240.14d-1 - Scope of and definitions applicable to Regulations 14D and 14E.

Code of Federal Regulations, 2014 CFR

2014-04-01

... its aggregate trading volume on securities exchanges in Canada and on the Canadian Dealing Network... accordance with the requirements of the home jurisdiction law or practice will satisfy the requirements of... jurisdiction law or practice will satisfy the requirements of § 240.14e-1(c). Where payment may not be made on...

48 CFR 1406.302-1 - Only one responsible source and no other supplies or services will satisfy agency requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... COMPETITION REQUIREMENTS Other Than Full and Open Competition 1406.302-1 Only one responsible source and no... 48 Federal Acquisition Regulations System 5 2010-10-01 2010-10-01 false Only one responsible source and no other supplies or services will satisfy agency requirements. 1406.302-1 Section 1406.302-1...

48 CFR 606.302-1 - Only one responsible source and no other supplies or services will satisfy agency requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... COMPETITION REQUIREMENTS Other Than Full and Open Competition 606.302-1 Only one responsible source and no... 48 Federal Acquisition Regulations System 4 2010-10-01 2010-10-01 false Only one responsible source and no other supplies or services will satisfy agency requirements. 606.302-1 Section 606.302-1...

48 CFR 6.302-1 - Only one responsible source and no other supplies or services will satisfy agency requirements.

Code of Federal Regulations, 2011 CFR

2011-10-01

... REQUIREMENTS Other Than Full and Open Competition 6.302-1 Only one responsible source and no other supplies or... sources, and no other type of supplies or services will satisfy agency requirements, full and open... from the original source in the case of a follow-on contract for the continued development or...

What is satisfying about satisfying events? Testing 10 candidate psychological needs.

PubMed

Sheldon, K M; Elliot, A J; Kim, Y; Kasser, T

2001-02-01

Three studies compared 10 candidate psychological needs in an attempt to determine which are truly most fundamental for humans. Participants described "most satisfying events" within their lives and then rated the salience of each of the 10 candidate needs within these events. Supporting self-determination theory postulates (Ryan & Deci, 2000)--autonomy, competence, and relatedness, were consistently among the top 4 needs, in terms of both their salience and their association with event-related affect. Self-esteem was also important, whereas self-actualization or meaning, physical thriving, popularity or influence, and money-luxury were less important. This basic pattern emerged within three different time frames and within both U.S. and South Korean samples and also within a final study that asked, "What's unsatisfying about unsatisfying events?" Implications for hierarchical theories of needs are discussed.

Turbojet-engine Starting and Acceleration

NASA Technical Reports Server (NTRS)

Mc Cafferty, R. J.; Straight, D. M.

1956-01-01

From considerations of safety and reliability in performance of gas-turbine aircraft, it is clear that engine starting and acceleration are of utmost importance. For this reason extensive efforts have been devoted to the investigation of the factors involved in the starting and acceleration of engines. In chapter III it is shown that certain basic combustion requirements must be met before ignition can occur; consequently, the design and operation of an engine must be tailored to provide these basic requirements in the combustion zone of the engine, particularly in the vicinity of the ignition source. It is pointed out in chapter III that ignition by electrical discharges is aided by high pressure, high temperature, low gas velocity and turbulence, gaseous fuel-air mixture, proper mixture strength, and-an optimum spark. duration. The simultaneous achievement of all these requirements in an actual turbojet-engine combustor is obviously impossible, yet any attempt to satisfy as many requirements as possible will result in lower ignition energies, lower-weight ignition systems, and greater reliability. These factors together with size and cost considerations determine the acceptability of the final ignition system. It is further shown in chapter III that the problem of wall quenching affects engine starting. For example, the dimensions of the volume to be burned must be larger than the quenching distance at the lowest pressure and the most adverse fuel-air ratio encountered. This fact affects the design of cross-fire tubes between adjacent combustion chambers in a tubular-combustor turbojet engine. Only two chambers in these engines contain spark plugs; therefore, the flame must propagate through small connecting tubes between the chambers. The quenching studies indicate that if the cross-fire tubes are too narrow the flame will not propagate from one chamber to another. In order to better understand the role of the basic factors in actual engine operation, many investigations have been conducted in single combustors from gas-turbine engines and in full-scale engines in altitude tanks and in flight. The purpose of the present chapter is to discuss the results of such studies and, where possible, to interpret these results qualitatively in terms of the basic requirements reported in chapter III. The discussion parallels the three phases of turbojet engine starting: (1) Ignition of the fuel-air mixture (2) Propagation of flame throughout the combustion zone (3) Acceleration of the engine to operating speed.

Ethics and regulation in organ procurement research.

PubMed

Ackerman, Terrence F; Winsett, Rebecca P

2002-12-01

This article explores the role of ethics and regulation in human research conducted by organ procurement agencies; basic ethical principles for human research are outlined. Organ procurement agencies are not required to observe federal regulations; however, voluntary adherence will ensure that procurement research is conducted according to current standards of ethical practice. Although most organ procurement research will qualify for exempt status, this determination should be made by an institutional review board. Even if studies qualify for exempt status, there is a moral presumption that informed consent should be sought, unless certain narrow conditions for waiver of consent are satisfied. Finally, when future research utilizing organ procurement records is anticipated, procurement coordinators should provide sufficiently detailed information to families about such plans to permit their advance informed consent to research activities.

Dynamic interferometer alignment and its utility in UV Fourier transform spectrometer systems

NASA Technical Reports Server (NTRS)

Dorval, Rick K.; Engel, James R.; Wyntjes, Geert J.

1993-01-01

Dynamic alignment has been demonstrated as a practical approach to alignment maintenance for systems in the infrared region of the spectrum. On the basis of work done by OPTRA, this technique was introduced in commercial Fourier transform spectrometer systems in 1982 and in various forms is now available from a number of manufacturers. This paper reports on work by OPTRA to extend the basic technique to systems operating in the ultraviolet. In addition, this paper reports the preliminary results of the development of an alignment system using a laser diode in place of a gas laser normally found in dynamic alignment systems. A unique optical system and spatial heterodyne technique allows for achievement of a metrology system with characteristics that fully satisfy the requirements of an ultraviolet spectrometer system.

Requirements based system risk modeling

NASA Technical Reports Server (NTRS)

Meshkat, Leila; Cornford, Steven; Feather, Martin

2004-01-01

The problem that we address in this paper is assessing the expected degree of success of the system or mission based on the degree to which each requirement is satisfied and the relative weight of the requirements. We assume a complete list of the requirements, the relevant risk elements and their probability of occurrence and the quantified effect of the risk elements on the requirements. In order to assess the degree to which each requirement is satisfied, we need to determine the effect of the various risk elements on the requirement.

77 FR 75230 - Self-Regulatory Organizations; Chicago Board Options Exchange, Incorporated; Notice of Proposed...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-12-19

... Director Nominating Body and any petition candidate must satisfy the compositional requirements determined... Nominating Body and any petition candidate must satisfy the compositional requirements determined by the... with appropriate flexibility as it evaluates the structure and composition of its Board in the future...

48 CFR 9.202 - Policy.

Code of Federal Regulations, 2010 CFR

2010-10-01

... requirements that a potential offeror (or its product) must satisfy in order to become qualified. Only those... shall be provided— (i) All requirements that they or their products must satisfy to become qualified... services not provided under contract to the agency). (3) If the services in (a)(2)(ii) above are provided...

40 CFR 80.156 - Liability for violations of the interim detergent program controls and prohibitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

..., or detergent-additized post-refinery component satisfied relevant requirements when it left their... detergent satisfied all relevant requirements when it left the detergent manufacturer's control; and (B... manufactured. (2) The test results must accurately establish that, when it left the manufacturer's control, the...

A biorefinery for mobility?

PubMed

Pacca, S; Moreira, J R

2011-11-15

Biofuels are considered as a carbon neutral alternative to hydrocarbons in the transport sector and this approach has triggered concerns about the impact the production of biofuels might have on land usage. Another option that might also lead to reduced emissions in the transport sector is electricity based on renewable energy sources such as biomass. Below, we assess the benefits and drawbacks of the joint production of ethanol and electricity in a sugar cane based refinery, and the use of both energy forms in privately owned automobiles. In this analysis, we have considered technology for energy production that is currently available and cost competitive. The results show that the amount of land that is required to power our current automobile use needs is less than what is typically stated. According to our results that are based on 2010 values, 2 million ha of land are sufficient to power the Brazilian automobile fleet, 25 million ha are enough to satisfy the needs of the U.S. fleet, and 67 million ha are sufficient to cover the global autofuel requirements. When minor efficiency gains are considered, 19 million ha will be enough to satisfy the fuel needs of the U.S. fleet in 2030, whereas land required to supply the Brazilian and global fleet remain basically unchanged. Our analysis shows that the harvested energy density of sugar cane is 306 GJ/ha/yr, which is 1.7 times the value usually reported in the literature for biofuels. As a result, taking advantage of the primary energy potential of sugar cane, only 4% of the world's available cropland area would be sufficient to produce fuels that would power the global car fleet.

Compensation, benefits, and satisfaction: the Longitudinal Emergency Medical Technician Demographic Study (LEADS) Project.

PubMed

Brown, William E; Dawson, Drew; Levine, Roger

2003-01-01

To determine the compensation, benefit package, and level of satisfaction with the benefits of nationally registered emergency medical technicians (NREMTs) in 2001. The Longitudinal EMT Attribute Demographic Study (LEADS) Project included an 18-question snapshot survey on compensation with the 2001 core survey. This survey was sent to 4,835 randomly selected NREMTs. A total of 1,718 NREMT-Basics and NREMT-Paramedics, from 1,317 different postal zip codes, responded to the survey. Most NREMTs in the survey (86% of the compensated NREMT-Basics and 85% of the compensated NREMT-Paramedics) were employed primarily as patient care providers. For their emergency medical services (EMS) work in the previous 12 months, compensated NREMT-Basics had mean earnings of 18,324 US dollars (standard error, 978 US dollars) and compensated NREMT-Paramedics had mean earnings of 34,654 US dollars (standard error, 646 US dollars). At least 26% of compensated NREMT-Basics and 9% of compensated NREMT-Paramedics had no health insurance. The majority of compensated NREMTs (62% of the Basics and 57% of the Paramedics) reported their retirement plans were not adequate to meet their financial needs. EMTs are not satisfied with the appreciation and recognition they receive from EMS employers. About one-third (35% of the compensated NREMT-Basics and 30% of the compensated NREMT-Paramedics) were not satisfied with all of the benefits they receive from their EMS employer. Nearly all (94% of both compensated NREMT-Basics and NREMT-Paramedics) believed that EMTs should be paid more for the job that they do. The adequacy of EMT compensation and benefit packages is an area of concern. It is not unreasonable to believe that these factors are associated with EMT retention and attrition. Additional longitudinal EMT information on compensation and benefits are anticipated to determine the extent to which compensation and benefits are factors in EMT retention.

A pilot study for the analysis of dream reports using Maslow's need categories: an extension to the emotional selection hypothesis.

PubMed

Coutts, Richard

2010-10-01

The emotional selection hypothesis describes a cyclical process that uses dreams to modify and test select mental schemas. An extension is proposed that further characterizes these schemas as facilitators of human need satisfaction. A pilot study was conducted in which this hypothesis was tested by assigning 100 dream reports (10 randomly selected from 10 dream logs at an online web site) to one or more categories within Maslow's hierarchy of needs. A "match" was declared when at least two of three judges agreed both for category and for whether the identified need was satisfied or thwarted in the dream narrative. The interjudge reliability of the judged needs was good (92% of the reports contained at least one match). The number of needs judged as thwarted did not differ significantly from the number judged as satisfied (48 vs. 52%, respectively). The six "higher" needs (belongingness, esteem, cognitive, aesthetic, self-actualization, and transcendence) were scored significantly more frequently (81%) than were the two lowest or "basic" needs (physiological and safety, 19%). Basic needs were also more likely to be judged as thwarted, while higher needs were more likely to be judged as satisfied. These findings are discussed in the context of Maslow's hierarchy of needs as a framework for investigating theories of dream function, including the emotional selection hypothesis and other contemporary dream theories.

Design concepts for the Centrifuge Facility Life Sciences Glovebox

NASA Technical Reports Server (NTRS)

Sun, Sidney C.; Horkachuck, Michael J.; Mckeown, Kellie A.

1989-01-01

The Life Sciences Glovebox will provide the bioisolated environment to support on-orbit operations involving non-human live specimens and samples for human life sceinces experiments. It will be part of the Centrifuge Facility, in which animal and plant specimens are housed in bioisolated Habitat modules and transported to the Glovebox as part of the experiment protocols supported by the crew. At the Glovebox, up to two crew members and two habitat modules must be accommodated to provide flexibility and support optimal operations. This paper will present several innovative design concepts that attempt to satisfy the basic Glovebox requirements. These concepts were evaluated for ergonomics and ease of operations using computer modeling and full-scale mockups. The more promising ideas were presented to scientists and astronauts for their evaluation. Their comments, and the results from other evaluations are presented. Based on the evaluations, the authors recommend designs and features that will help optimize crew performance and facilitate science accommodations, and specify problem areas that require further study.

BLSS: A Contribution to Future Life Support

NASA Technical Reports Server (NTRS)

Skoog, A. I.

1985-01-01

The problem of the supply of basic life supporting ingredients was analyzed. Storage volume and launch weight of water, oxygen and food in a conventional nonregenerable life support system are directly proportional to the crew size and the length of the mission. Because of spacecraft payload limitations this requires that the carbon, or food, recycling loop, the third and final part in the life support system, be closed to further reduce logistics cost. Advanced life support systems need to be developed in which metabolic waste products are regenerated and food is produced. Biological life support systems (BLSS) satisfy the space station environmental control functions and close the food cycle. Numerous scientific space experiments were delineated, the results of which are applicable to the support of BLSS concepts. Requirements and concepts are defined and the feasibility of BLSS for space application are analyzed. The BLSS energy mass relation, and the possibilities to influence it to achieve advantages for the BLSS are determined. A program for the development of BLSS is proposed.

An Approach to Providing a User Interface for Military Computer-Aided-Instruction in 1980.

ERIC Educational Resources Information Center

Gallenson, Louis

A recent needs study determined that most of the terminal requirements for military computer assisted instruction (CAI) applications can be satisfied with mainstream commercial terminals. Additional development, however, is likely to be required to satisfy two of the capabilities (limited graphics and prerecorded visuals). The expected…

40 CFR 80.169 - Liability for violations of the detergent certification program controls and prohibitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

...-additized PRC satisfied relevant requirements when it left the party's control; and (iii) That the party has... satisfied all relevant requirements when it left the detergent manufacturer's control. (B) Written blending... was manufactured. (2) To establish that, when it left the manufacturer's control, the detergent...

More Similar but Less Satisfying: Comparing Preferences for and the Efficacy of Within- and Cross-Category Substitutes for Food.

PubMed

Huh, Young Eun; Vosgerau, Joachim; Morewedge, Carey K

2016-06-01

When people cannot get what they want, they often satisfy their desire by consuming a substitute. Substitutes can originate from within the taxonomic category of the desired stimulus (i.e., within-category substitutes) or from a different taxonomic category that serves the same basic goal (i.e., cross-category substitutes). Both a store-brand chocolate (within-category substitute) and a granola bar (cross-category substitute), for example, can serve as substitutes for gourmet chocolate. Here, we found that people believe that within-category substitutes, which are more similar to desired stimuli, will more effectively satisfy their cravings than will cross-category substitutes (Experiments 1, 2a, and 2b). However, because within-category substitutes are more similar than cross-category substitutes to desired stimuli, they are more likely to evoke an unanticipated negative contrast effect. As a result, unless substitutes are equivalent in quality to the desired stimulus, cross-category substitutes more effectively satisfy cravings for the desired stimulus (Experiments 3 and 4). © The Author(s) 2016.

A Viking satellite orbit trim strategy

NASA Technical Reports Server (NTRS)

Hintz, G. R.

1971-01-01

One strategy is submitted for meeting the varied and stringent requirements of the Viking Project on the control of the satellite orbit to obtain reconnaissance and to prepare for lander release. To satisfy these requirements, different orbit trim maneuver strategies were developed for two typical Viking missions. In addition, a summary of recent numerical results is included to show that this strategy satisfies the mission requirements which have been identified.

A Pathway to Learner Autonomy: A Self-Determination Theory Perspective

ERIC Educational Resources Information Center

Hu, Pingying; Zhang, Jiaxiu

2017-01-01

Concepts of learner autonomy and the self-determination theory provided a theoretical rationale for the action program for learner autonomy. The action program incorporated satisfying learners' basic psychological needs into English Foreign Language (EFL) course education. The action program was implemented for one academic year. Both qualitative…

Health, Supportive Environments, and the Reasonable Person Model

Treesearch

Stephen Kaplan; Rachel Kaplan

2003-01-01

The Reasonable Person Model is a conceptual framework that links environmental factors with human behavior. People are more reasonable, cooperative, helpful, and satisfied when the environment supports their basic informational needs. The same environmental supports are important factors in enhancing human health. We use this framework to identify the informational...

Designing and Building a Collaborative Library Intranet for All

ERIC Educational Resources Information Center

Battles, Jason J.

2010-01-01

Intranets should provide quick and easy access to organizational information. The University of Alabama Libraries' intranet was only partially satisfying this basic expectation. Librarians could use it to find forms, policies, committee assignments, and meeting minutes, but navigating the libraries' intranet was neither quick nor easy, and it was…

A New Look at School Failure and School Success.

ERIC Educational Resources Information Center

Glasser, William

1997-01-01

The cause of school and marriage failure is that most people practice stimulus-response psychology. Choice theory helps nurture the warm, supportive human relationships that students need for school success and couples need for marital success. Satisfying four basic psychological needs (for belonging, power, freedom, and fun) helps humans create…

The Immersion Instructional Model: A Report from the Work Place.

ERIC Educational Resources Information Center

Watt, David M.; Jones, Paul

Any proposal for training has to satisfy two major components: it must be job relevant and be accomplished without major interruption of work schedules, while incorporating strategies to help eliminate absenteeism. One recently developed model for basic skills training, the Immersion Instructional Model, meets these criteria and provides…

Some problems with pro-competition reforms.

PubMed

Agich, G J; Begley, C E

1985-01-01

As the search for effective cost-containment policies continues, health care reform along pro-competition lines has gained considerable backing in the United States. By offering market competition to achieve allocational efficiency and vouchers and tax credits to achieve distributional equity, pro-competition reforms appear to satisfy what many believed were incommensurable goals. A critical review of this strategy reveals two practical difficulties, however. The first concerns the ambiguity arising from the proposals' reliance on the concept of equal access to some basic level of health care as its distributional objective and the second concerns the ethical dilemma arising from the proposals' reliance on physicians as rationers of health care. In considering the distributional goal of guaranteeing access to a basic minimum of health care, we argue that, despite its theoretical attractiveness, there exists no acceptable way of determining or justifying its content, and without a clear definition of the basic minimum there is no guarantee that any equity objective will be achieved under the pro-competition strategy. With regard to the use of physicians and other providers as society's gatekeepers, we point out that this role is in direct conflict with traditional responsibilities that patients expect providers to assume. Requiring doctors to ration services in response to market incentives may further erode the trust relationship between physicians and patients, and clearly puts the more seriously ill at a disadvantage.

26 CFR 1.401(a)(4)-6 - Contributory defined benefit plans.

Code of Federal Regulations, 2011 CFR

2011-04-01

... to satisfy this paragraph (b)(2)(ii)(A) merely because it eliminates employee contributions for all... requirements—(1) In general. A contributory DB plan satisfies this paragraph (b)(2)(ii)(B) if it satisfies... employee's base benefit percentage as required under paragraph (b)(2)(iii)(B)(1) of this section, it may be...

26 CFR 1.401(a)(4)-6 - Contributory defined benefit plans.

Code of Federal Regulations, 2014 CFR

2014-04-01

... to satisfy this paragraph (b)(2)(ii)(A) merely because it eliminates employee contributions for all... requirements—(1) In general. A contributory DB plan satisfies this paragraph (b)(2)(ii)(B) if it satisfies... employee's base benefit percentage as required under paragraph (b)(2)(iii)(B)(1) of this section, it may be...

26 CFR 1.401(a)(4)-6 - Contributory defined benefit plans.

Code of Federal Regulations, 2012 CFR

2012-04-01

... to satisfy this paragraph (b)(2)(ii)(A) merely because it eliminates employee contributions for all... requirements—(1) In general. A contributory DB plan satisfies this paragraph (b)(2)(ii)(B) if it satisfies... employee's base benefit percentage as required under paragraph (b)(2)(iii)(B)(1) of this section, it may be...

26 CFR 1.401(a)(4)-6 - Contributory defined benefit plans.

Code of Federal Regulations, 2013 CFR

2013-04-01

... to satisfy this paragraph (b)(2)(ii)(A) merely because it eliminates employee contributions for all... requirements—(1) In general. A contributory DB plan satisfies this paragraph (b)(2)(ii)(B) if it satisfies... employee's base benefit percentage as required under paragraph (b)(2)(iii)(B)(1) of this section, it may be...

34 CFR 76.592 - Federal evaluation-satisfying requirement for State or subgrantee evaluation.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 34 Education 1 2010-07-01 2010-07-01 false Federal evaluation-satisfying requirement for State or subgrantee evaluation. 76.592 Section 76.592 Education Office of the Secretary, Department of Education STATE-ADMINISTERED PROGRAMS What Conditions Must Be Met by the State and Its Subgrantees? Evaluation § 76.592 Federal...

20 CFR 901.31 - Grounds for suspension or termination of enrollment.

Code of Federal Regulations, 2012 CFR

2012-04-01

... enrollment. 901.31 Section 901.31 Employees' Benefits JOINT BOARD FOR THE ENROLLMENT OF ACTUARIES REGULATIONS...) Failure to satisfy requirements for enrollment. The enrollment of an actuary may be terminated if it is found that the actuary did not satisfy the eligibility requirements set forth in § 901.11 or § 901.12...

20 CFR 901.31 - Grounds for suspension or termination of enrollment.

Code of Federal Regulations, 2013 CFR

2013-04-01

... enrollment. 901.31 Section 901.31 Employees' Benefits JOINT BOARD FOR THE ENROLLMENT OF ACTUARIES REGULATIONS...) Failure to satisfy requirements for enrollment. The enrollment of an actuary may be terminated if it is found that the actuary did not satisfy the eligibility requirements set forth in § 901.11 or § 901.12...

20 CFR 901.31 - Grounds for suspension or termination of enrollment.

Code of Federal Regulations, 2014 CFR

2014-04-01

... enrollment. 901.31 Section 901.31 Employees' Benefits JOINT BOARD FOR THE ENROLLMENT OF ACTUARIES REGULATIONS...) Failure to satisfy requirements for enrollment. The enrollment of an actuary may be terminated if it is found that the actuary did not satisfy the eligibility requirements set forth in § 901.11 or § 901.12...

20 CFR 901.31 - Grounds for suspension or termination of enrollment.

Code of Federal Regulations, 2011 CFR

2011-04-01

... enrollment. 901.31 Section 901.31 Employees' Benefits JOINT BOARD FOR THE ENROLLMENT OF ACTUARIES REGULATIONS...) Failure to satisfy requirements for enrollment. The enrollment of an actuary may be terminated if it is found that the actuary did not satisfy the eligibility requirements set forth in §§ 901.12 or 901.13...

29 CFR 2520.101-3 - Notice of blackout periods under individual account plans.

Code of Federal Regulations, 2010 CFR

2010-07-01

... paragraph 4. of the model notice in paragraph (e)(2) of this section will satisfy this requirement); (v) In.... of the model notice in paragraph (e)(2) of this section will satisfy this requirement), and (B) An... three consecutive business days. (ii) Exclusions. The term “blackout period” does not include a...

20 CFR 901.31 - Grounds for suspension or termination of enrollment.

Code of Federal Regulations, 2010 CFR

2010-04-01

... enrollment. 901.31 Section 901.31 Employees' Benefits JOINT BOARD FOR THE ENROLLMENT OF ACTUARIES REGULATIONS...) Failure to satisfy requirements for enrollment. The enrollment of an actuary may be terminated if it is found that the actuary did not satisfy the eligibility requirements set forth in §§ 901.12 or 901.13...

Attitude Design for the LADEE Mission

NASA Technical Reports Server (NTRS)

Galal, Ken; Nickel, Craig; Sherman, Ryan

2015-01-01

The Lunar Atmosphere and Dust Environment Explorer (LADEE) satellite successfully completed its 148-day science investigation in a low-altitude, near-equatorial lunar orbit on April 18, 2014. The LADEE spacecraft was built, managed and operated by NASA's Ames Research Center (ARC). The Mission Operations Center (MOC) was located at Ames and was responsible for activity planning, command sequencing, trajectory and attitude design, orbit determination, and spacecraft operations. The Science Operations Center (SOC) was located at Goddard Space Flight Center and was responsible for science planning, data archiving and distribution. This paper details attitude design and operations support for the LADEE mission. LADEE's attitude design was shaped by a wide range of instrument pointing requirements that necessitated regular excursions from the baseline one revolution per orbit "Ram" attitude. Such attitude excursions were constrained by a number of flight rules levied to protect instruments from the Sun, avoid geometries that would result in simultaneous occlusion of LADEE's two star tracker heads, and maintain the spacecraft within its thermal and power operating limits. To satisfy LADEE's many attitude requirements and constraints, a set of rules and conventions was adopted to manage the complexity of this design challenge and facilitate the automation of ground software that generated pointing commands spanning multiple days of operations at a time. The resulting LADEE Flight Dynamics System (FDS) that was developed used Visual Basic scripts that generated instructions to AGI's Satellite Tool Kit (STK) in order to derive quaternion commands at regular intervals that satisfied LADEE's pointing requirements. These scripts relied heavily on the powerful "align and constrain" capability of STK's attitude module to construct LADEE's attitude profiles and the slews to get there. A description of the scripts and the attitude modeling they embodied is provided. One particular challenge analysts faced was in the design of LADEE maneuver attitudes. A flight rule requiring pre-maneuver verification of in-flight maneuver conditions by ground operators prior to burn execution resulted in the need to accommodate long periods in the maneuver attitude. This in turn complicated efforts to satisfy star tracker interference and communication constraints in lunar orbit. In response to this challenge, a graphical method was developed and used to survey candidate rotation angles about the thrust vector. This survey method is described and an example of its use on a particular LADEE maneuver is discussed. Finally, the software and methodology used to satisfy LADEE's attitude requirements are also discussed in the context of LADEE's overall activity planning effort. In particular, the way in which strategic schedules of instrument and engineering activities were translated into actual attitude profiles at the tactical level, then converted into precise quaternion commands to achieve those pointing goals is explained. In order to reduce the risk of time-consuming re-planning efforts, this process included the generation of long-term projections of constraint violation predictions for individual attitude profiles that could be used to establish keep-out time-frames for particular attitude profiles. The challenges experienced and overall efficacy of both the overall LADEE ground system and the attitude components of the Flight Dynamics System in meeting LADEE's varied pointing requirements are discussed.

An assessment of envelope-based demodulation in case of proximity of carrier and modulation frequencies

NASA Astrophysics Data System (ADS)

Shahriar, Md Rifat; Borghesani, Pietro; Randall, R. B.; Tan, Andy C. C.

2017-11-01

Demodulation is a necessary step in the field of diagnostics to reveal faults whose signatures appear as an amplitude and/or frequency modulation. The Hilbert transform has conventionally been used for the calculation of the analytic signal required in the demodulation process. However, the carrier and modulation frequencies must meet the conditions set by the Bedrosian identity for the Hilbert transform to be applicable for demodulation. This condition, basically requiring the carrier frequency to be sufficiently higher than the frequency of the modulation harmonics, is usually satisfied in many traditional diagnostic applications (e.g. vibration analysis of gear and bearing faults) due to the order-of-magnitude ratio between the carrier and modulation frequency. However, the diversification of the diagnostic approaches and applications shows cases (e.g. electrical signature analysis-based diagnostics) where the carrier frequency is in close proximity to the modulation frequency, thus challenging the applicability of the Bedrosian theorem. This work presents an analytic study to quantify the error introduced by the Hilbert transform-based demodulation when the Bedrosian identity is not satisfied and proposes a mitigation strategy to combat the error. An experimental study is also carried out to verify the analytical results. The outcome of the error analysis sets a confidence limit on the estimated modulation (both shape and magnitude) achieved through the Hilbert transform-based demodulation in case of violated Bedrosian theorem. However, the proposed mitigation strategy is found effective in combating the demodulation error aroused in this scenario, thus extending applicability of the Hilbert transform-based demodulation.

A Variational Assimilation Method for Satellite and Conventional Data: a Revised Basic Model 2B

NASA Technical Reports Server (NTRS)

Achtemeier, Gary L.; Scott, Robert W.; Chen, J.

1991-01-01

A variational objective analysis technique that modifies observations of temperature, height, and wind on the cyclone scale to satisfy the five 'primitive' model forecast equations is presented. This analysis method overcomes all of the problems that hindered previous versions, such as over-determination, time consistency, solution method, and constraint decoupling. A preliminary evaluation of the method shows that it converges rapidly, the divergent part of the wind is strongly coupled in the solution, fields of height and temperature are well-preserved, and derivative quantities such as vorticity and divergence are improved. Problem areas are systematic increases in the horizontal velocity components, and large magnitudes of the local tendencies of the horizontal velocity components. The preliminary evaluation makes note of these problems but detailed evaluations required to determine the origin of these problems await future research.

Quantum correlations in multipartite quantum systems

NASA Astrophysics Data System (ADS)

Jafarizadeh, M. A.; Heshmati, A.; Karimi, N.; Yahyavi, M.

2018-03-01

Quantum entanglement is the most famous type of quantum correlation between elements of a quantum system that has a basic role in quantum communication protocols like quantum cryptography, teleportation and Bell inequality detection. However, it has already been shown that various applications in quantum information theory do not require entanglement. Quantum discord as a new kind of quantum correlations beyond entanglement, is the most popular candidate for general quantum correlations. In this paper, first we find the entanglement witness in a particular multipartite quantum system which consists of a N-partite system in 2 n -dimensional space. Then we give an exact analytical formula for the quantum discord of this system. At the end of the paper, we investigate the additivity relation of the quantum correlation and show that this relation is satisfied for a N-partite system with 2 n -dimensional space.

Research on SEU hardening of heterogeneous Dual-Core SoC

NASA Astrophysics Data System (ADS)

Huang, Kun; Hu, Keliu; Deng, Jun; Zhang, Tao

2017-08-01

The implementation of Single-Event Upsets (SEU) hardening has various schemes. However, some of them require a lot of human, material and financial resources. This paper proposes an easy scheme on SEU hardening for Heterogeneous Dual-core SoC (HD SoC) which contains three techniques. First, the automatic Triple Modular Redundancy (TMR) technique is adopted to harden the register heaps of the processor and the instruction-fetching module. Second, Hamming codes are used to harden the random access memory (RAM). Last, a software signature technique is applied to check the programs which are running on CPU. The scheme need not to consume additional resources, and has little influence on the performance of CPU. These technologies are very mature, easy to implement and needs low cost. According to the simulation result, the scheme can satisfy the basic demand of SEU-hardening.

Universal behavior of generalized causal set d’Alembertians in curved spacetime

NASA Astrophysics Data System (ADS)

Belenchia, Alessio

2016-07-01

Causal set non-local wave operators allow both for the definition of an action for causal set theory and the study of deviations from local physics that may have interesting phenomenological consequences. It was previously shown that, in all dimensions, the (unique) minimal discrete operators give averaged continuum non-local operators that reduce to \\square -R/2 in the local limit. Recently, dropping the constraint of minimality, it was shown that there exist an infinite number of discrete operators satisfying basic physical requirements and with the right local limit in flat spacetime. In this work, we consider this entire class of generalized causal set d’Alembertins in curved spacetimes and extend to them the result about the universality of the -R/2 factor. Finally, we comment on the relation of this result to the Einstein equivalence principle.

Restoring the consistency with the contact density theorem of a classical density functional theory of ions at a planar electrical double layer.

PubMed

Gillespie, Dirk

2014-11-01

Classical density functional theory (DFT) of fluids is a fast and efficient theory to compute the structure of the electrical double layer in the primitive model of ions where ions are modeled as charged, hard spheres in a background dielectric. While the hard-core repulsive component of this ion-ion interaction can be accurately computed using well-established DFTs, the electrostatic component is less accurate. Moreover, many electrostatic functionals fail to satisfy a basic theorem, the contact density theorem, that relates the bulk pressure, surface charge, and ion densities at their distances of closest approach for ions in equilibrium at a smooth, hard, planar wall. One popular electrostatic functional that fails to satisfy the contact density theorem is a perturbation approach developed by Kierlik and Rosinberg [Phys. Rev. A 44, 5025 (1991)PLRAAN1050-294710.1103/PhysRevA.44.5025] and Rosenfeld [J. Chem. Phys. 98, 8126 (1993)JCPSA60021-960610.1063/1.464569], where the full free-energy functional is Taylor-expanded around a bulk (homogeneous) reference fluid. Here, it is shown that this functional fails to satisfy the contact density theorem because it also fails to satisfy the known low-density limit. When the functional is corrected to satisfy this limit, a corrected bulk pressure is derived and it is shown that with this pressure both the contact density theorem and the Gibbs adsorption theorem are satisfied.

Basic targeting strategies for rendezvous and flyby missions to the near-Earth asteroids

NASA Astrophysics Data System (ADS)

Perozzi, Ettore; Rossi, Alessandro; Valsecchi, Giovanni B.

2001-01-01

Missions to asteroids and comets are becoming increasingly feasible both from a technical and a financial point of view. In particular, those directed towards the Near-Earth Asteroids have proven suitable for a low-cost approach, thus attracting the major space agencies as well as private companies. The choice of a suitable target involves both scientific relevance and mission design considerations, being often a difficult task to accomplish due to the limited energy budget at disposal. The aim of this paper is to provide an approach to basic trajectory design which allows to account for both aspects of the problem, taking into account scientific and technical information. A global characterization of the Near-Earth Asteroids population carried out on the basis of their dynamics, physical properties and flight dynamics considerations, allows to identify a group of candidates which satisfy both, the scientific and engineering requirements. The feasibility of rendezvous and flyby missions towards them is then discussed and the possibility of repeated encounters with the same object is investigated, as an intermediate scenario. Within this framework, the capability of present and near future launch and propulsion systems for interplanetary missions is also addressed.

Educational Criteria for Evaluating Simple Class Diagrams Made by Novices for Conceptual Modeling

ERIC Educational Resources Information Center

Kayama, Mizue; Ogata, Shinpei; Asano, David K.; Hashimoto, Masami

2016-01-01

Conceptual modeling is one of the most important learning topics for higher education and secondary education. The goal of conceptual modeling in this research is to draw a class diagram using given notation to satisfy the given requirements. In this case, the subjects are asked to choose concepts to satisfy the given requirements and to correctly…

Calibration Of Partial-Pressure-Of-Oxygen Sensors

NASA Technical Reports Server (NTRS)

Yount, David W.; Heronimus, Kevin

1995-01-01

Report and analysis of, and discussion of improvements in, procedure for calibrating partial-pressure-of-oxygen sensors to satisfy Spacelab calibration requirements released. Sensors exhibit fast drift, which results in short calibration period not suitable for Spacelab. By assessing complete process of determining total drift range available, calibration procedure modified to eliminate errors and still satisfy requirements without compromising integrity of system.

How Do I Satisfy the General Education Language Requirement? University Students' Attitudes toward Language Study

ERIC Educational Resources Information Center

Thomas, Juan Antonio

2010-01-01

This study aims to identify the two principal reasons why college students choose a certain language to satisfy a general education second language requirement by polling 172 students enrolled in first-year language courses in 13 languages at a large Northeastern research university. Students answered a questionnaire and chose the two main reasons…

Assessment of Dog Guides by Users in Japan and Suggestions for Improvement

ERIC Educational Resources Information Center

Koda, Naoko; Kubo, Masumi; Ishigami, Tomomi; Furuhashi, Hiroaki

2011-01-01

Dog guide users in Japan were mostly satisfied with and used their dogs frequently; however, they requested some improvements in training and in basic guiding work. The findings of the study suggest the need for further improvement of training methods, considering cultural factors and individual users' needs. (Contains 3 tables.)

The Decline of Academic Motivation during Adolescence: An Accelerated Longitudinal Cohort Analysis on the Effect of Psychological Need Satisfaction

ERIC Educational Resources Information Center

Gnambs, Timo; Hanfstingl, Barbara

2016-01-01

Adolescents typically exhibit a marked decline in academic intrinsic motivation throughout their school careers. Following self-determination theory, it is hypothesised that traditional school environments insufficiently satisfy three basic psychological needs of youths during maturation, namely the needs for autonomy, competence and relatedness.…

You Are a Storyteller!

ERIC Educational Resources Information Center

Wilcox, Susan

The aim of this presentation is to persuade early childhood educators that they can and should tell stories to children in their preschool classes, day care homes, or centers. The story of Scheherezade is retold in order to illuminate the points that: (1) traditional stories share a basic, satisfying structure which, regardless of the details of…

Derivation of Performance Statements for the Automotive Mechanics Basic Trade Course: Research Documentation.

ERIC Educational Resources Information Center

Fox, A. P.; Kuhl, D. H.

A project was conducted to derive a comprehensive list of the performances of a competence mechanic to satisfy the planning needs of automotive engineering lecturers, curriculum committees, researchers, course designers, and staff developers. A list of 127 tasks together with information about their relative importance and the frequency with which…

The Relation between Balanced Need Satisfaction and Adolescents' Motivation in Physical Education

ERIC Educational Resources Information Center

Mouratidis, Athanasios; Barkoukis, Vassilis; Tsorbatzoudis, Charalambos

2015-01-01

Self-determination theory posits that satisfaction of the needs for autonomy, competence and relatedness represents the basic nutriments for humans' optimal functioning. It also postulates that with greater the degree to which these three needs are equally satisfied, the quality of motivation is further enhanced. Yet, this premise has remained…

Nutrition in Children's Sports.

ERIC Educational Resources Information Center

Smith, Nathan J.

Young athletes need to be aware of the importance of good nutrition to athletic performance. A basic diet plan, worked out with a physician to satisfy energy and weight needs, is essential. The best eating schedule and amount and type of food varies with different sports depending on the intensity and duration of physical activity. Weight control…

Job satisfaction among nursing staff in a military health care facility.

PubMed

Allgood, C; O'Rourke, K; VanDerslice, J; Hardy, M A

2000-10-01

Job satisfaction in the workplace affects absenteeism, turnover, and performance. We conducted a cross-sectional study of 201 nursing personnel to assess satisfaction among nursing staff at a military hospital in the southwestern United States. Participants completed a self-administered survey in which they rated professional status, autonomy, pay, organizational policies, task requirements, and interaction by importance and satisfaction. Autonomy, professional status, and pay were the most important factors and organizational policies was the least important factor. Military staff were slightly more satisfied with staff interactions than civilian staff. Nursing personnel working in specialty care units were significantly more satisfied with interactions and professional status, but they valued organizational policies less than those working in general units. Professionals were significantly more satisfied with pay and autonomy, whereas nonprofessionals were more satisfied with task requirements and professional status.

The mediating role of social environmental factors in the associations between attachment styles and basic needs satisfaction.

PubMed

Felton, Luke; Jowett, Sophia

2013-01-01

The present study aimed to explore the mediating role of social factors on the associations between attachment styles and basic psychological needs satisfaction within two relational contexts. Athletes (N = 215) completed a multi-section questionnaire pertaining to attachment styles, basic needs satisfied within the coaching and the parental relational context, and such social factors as social support, interpersonal conflict, autonomy and controlling behaviours. Bootstrap mediation analysis revealed that the association between avoidant attachment style and basic needs satisfaction with the coach was mediated by social support and autonomy-related behaviours from the coach. The association between avoidant attachment style and basic needs satisfaction with the parent on the other hand was mediated by all social factors investigated. Finally, the association between anxious attachment style and basic needs satisfaction from the parent was mediated by conflict and controlling behaviours. Overall, the findings of the current study suggest that social factors play an important role in explaining the associations between attachment styles and basic needs satisfaction within two central relational contexts athletes operate in, and thus should be targeted in future interventions.

Elliptic biquaternion algebra

NASA Astrophysics Data System (ADS)

Özen, Kahraman Esen; Tosun, Murat

2018-01-01

In this study, we define the elliptic biquaternions and construct the algebra of elliptic biquaternions over the elliptic number field. Also we give basic properties of elliptic biquaternions. An elliptic biquaternion is in the form A0 + A1i + A2j + A3k which is a linear combination of {1, i, j, k} where the four components A0, A1, A2 and A3 are elliptic numbers. Here, 1, i, j, k are the quaternion basis of the elliptic biquaternion algebra and satisfy the same multiplication rules which are satisfied in both real quaternion algebra and complex quaternion algebra. In addition, we discuss the terms; conjugate, inner product, semi-norm, modulus and inverse for elliptic biquaternions.

15 CFR 781.4 - U.S. Government requests for information needed to satisfy the requirements of the APR or the Act.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 15 Commerce and Foreign Trade 2 2010-01-01 2010-01-01 false U.S. Government requests for information needed to satisfy the requirements of the APR or the Act. 781.4 Section 781.4 Commerce and Foreign Trade Regulations Relating to Commerce and Foreign Trade (Continued) BUREAU OF INDUSTRY AND SECURITY...

Einsteinian cubic gravity

NASA Astrophysics Data System (ADS)

Bueno, Pablo; Cano, Pablo A.

2016-11-01

We drastically simplify the problem of linearizing a general higher-order theory of gravity. We reduce it to the evaluation of its Lagrangian on a particular Riemann tensor depending on two parameters, and the computation of two derivatives with respect to one of those parameters. We use our method to construct a D -dimensional cubic theory of gravity which satisfies the following properties: (1) it shares the spectrum of Einstein gravity, i.e., it only propagates a transverse and massless graviton on a maximally symmetric background; (2) it is defined in the same way in general dimensions; (3) it is neither trivial nor topological in four dimensions. Up to cubic order in curvature, the only previously known theories satisfying the first two requirements are the Lovelock ones. We show that, up to cubic order, there exists only one additional theory satisfying requirements (1) and (2). Interestingly, this theory is, along with Einstein gravity, the only one which also satisfies (3).

A novel medical image data-based multi-physics simulation platform for computational life sciences.

PubMed

Neufeld, Esra; Szczerba, Dominik; Chavannes, Nicolas; Kuster, Niels

2013-04-06

Simulating and modelling complex biological systems in computational life sciences requires specialized software tools that can perform medical image data-based modelling, jointly visualize the data and computational results, and handle large, complex, realistic and often noisy anatomical models. The required novel solvers must provide the power to model the physics, biology and physiology of living tissue within the full complexity of the human anatomy (e.g. neuronal activity, perfusion and ultrasound propagation). A multi-physics simulation platform satisfying these requirements has been developed for applications including device development and optimization, safety assessment, basic research, and treatment planning. This simulation platform consists of detailed, parametrized anatomical models, a segmentation and meshing tool, a wide range of solvers and optimizers, a framework for the rapid development of specialized and parallelized finite element method solvers, a visualization toolkit-based visualization engine, a Python scripting interface for customized applications, a coupling framework, and more. Core components are cross-platform compatible and use open formats. Several examples of applications are presented: hyperthermia cancer treatment planning, tumour growth modelling, evaluating the magneto-haemodynamic effect as a biomarker and physics-based morphing of anatomical models.

Synthesizing Certified Code

NASA Technical Reports Server (NTRS)

Whalen, Michael; Schumann, Johann; Fischer, Bernd

2002-01-01

Code certification is a lightweight approach to demonstrate software quality on a formal level. Its basic idea is to require producers to provide formal proofs that their code satisfies certain quality properties. These proofs serve as certificates which can be checked independently. Since code certification uses the same underlying technology as program verification, it also requires many detailed annotations (e.g., loop invariants) to make the proofs possible. However, manually adding theses annotations to the code is time-consuming and error-prone. We address this problem by combining code certification with automatic program synthesis. We propose an approach to generate simultaneously, from a high-level specification, code and all annotations required to certify generated code. Here, we describe a certification extension of AUTOBAYES, a synthesis tool which automatically generates complex data analysis programs from compact specifications. AUTOBAYES contains sufficient high-level domain knowledge to generate detailed annotations. This allows us to use a general-purpose verification condition generator to produce a set of proof obligations in first-order logic. The obligations are then discharged using the automated theorem E-SETHEO. We demonstrate our approach by certifying operator safety for a generated iterative data classification program without manual annotation of the code.

Design enhancement tools in MSC/NASTRAN

NASA Technical Reports Server (NTRS)

Wallerstein, D. V.

1984-01-01

Design sensitivity is the calculation of derivatives of constraint functions with respect to design variables. While a knowledge of these derivatives is useful in its own right, the derivatives are required in many efficient optimization methods. Constraint derivatives are also required in some reanalysis methods. It is shown where the sensitivity coefficients fit into the scheme of a basic organization of an optimization procedure. The analyzer is to be taken as MSC/NASTRAN. The terminator program monitors the termination criteria and ends the optimization procedure when the criteria are satisfied. This program can reside in several plances: in the optimizer itself, in a user written code, or as part of the MSC/EOS (Engineering Operating System) MSC/EOS currently under development. Since several excellent optimization codes exist and since they require such very specialized technical knowledge, the optimizer under the new MSC/EOS is considered to be selected and supplied by the user to meet his specific needs and preferences. The one exception to this is a fully stressed design (FSD) based on simple scaling. The gradients are currently supplied by various design sensitivity options now existing in MSC/NASTRAN's design sensitivity analysis (DSA).

Technical guidance and analytic services in support of SEASAT-A. [radar altimeters for altimetry and ocean wave height

NASA Technical Reports Server (NTRS)

Brooks, W. L.; Dooley, R. P.

1975-01-01

The design of a high resolution radar for altimetry and ocean wave height estimation was studied. From basic principles, it is shown that a short pulse wide beam radar is the most appropriate and recommended technique for measuring both altitude and ocean wave height. To achieve a topographic resolution of + or - 10 cm RMS at 5.0 meter RMS wave heights, as required for SEASAT-A, it is recommended that the altimeter design include an onboard adaptive processor. The resulting design, which assumes a maximum likelihood estimation (MLE) processor, is shown to satisfy all performance requirements. A design summary is given for the recommended radar altimeter, which includes a full deramp STRETCH pulse compression technique followed by an analog filter bank to separate range returns as well as the assumed MLE processor. The feedback loop implementation of the MLE on a digital computer was examined in detail, and computer size, estimation accuracies, and bias due to range sidelobes are given for the MLE with typical SEASAT-A parameters. The standard deviation of the altitude estimate was developed and evaluated for several adaptive and nonadaptive split-gate trackers. Split-gate tracker biases due to range sidelobes and transmitter noise are examined. An approximate closed form solution for the altimeter power return is derived and evaluated. The feasibility of utilizing the basic radar altimeter design for the measurement of ocean wave spectra was examined.

A Linear Programming Approach to Routing Control in Networks of Constrained Nonlinear Positive Systems with Concave Flow Rates

NASA Technical Reports Server (NTRS)

Arneson, Heather M.; Dousse, Nicholas; Langbort, Cedric

2014-01-01

We consider control design for positive compartmental systems in which each compartment's outflow rate is described by a concave function of the amount of material in the compartment.We address the problem of determining the routing of material between compartments to satisfy time-varying state constraints while ensuring that material reaches its intended destination over a finite time horizon. We give sufficient conditions for the existence of a time-varying state-dependent routing strategy which ensures that the closed-loop system satisfies basic network properties of positivity, conservation and interconnection while ensuring that capacity constraints are satisfied, when possible, or adjusted if a solution cannot be found. These conditions are formulated as a linear programming problem. Instances of this linear programming problem can be solved iteratively to generate a solution to the finite horizon routing problem. Results are given for the application of this control design method to an example problem. Key words: linear programming; control of networks; positive systems; controller constraints and structure.

Smart Training: The Manager's Guide to Training for Improved Performance.

ERIC Educational Resources Information Center

Carr, Clay

This book describes and advocates "smart training," an approach to on-the-job training that helps employees gain competence and empowers them to act to satisfy customers. The book is organized in 16 chapters grouped into 4 parts. Part 1 outlines the basics of smart training, including its performance base, the need for initial analysis,…

Beyond the Systems Approach to Family Therapy: An Ecological Perspective.

ERIC Educational Resources Information Center

Coleman, Paul R.; Griffith, Mariellen

A brief review of systems theory provides a rationale for an underlying theoretical model within which systems theory can be more completely understood. The essence of the model is that persons are the major unit of study because the available means of satisfying "basic needs" define and shape interaction patterns in the family as in other human…

26 CFR 1.401(a)(4)-3 - Nondiscrimination in amount of employer-provided benefits under a defined benefit plan.

Code of Federal Regulations, 2013 CFR

2013-04-01

... satisfies the ratio percentage test of § 1.410(b)-2(b)(2) because the ratio percentage of the rate group is... percent).) (g) Rate group 51 satisfies the ratio percentage test of § 1.410(b)-2(b)(2) because the ratio... uniform benefits are permitted to satisfy this requirement by meeting one of the safe harbors in paragraph...

26 CFR 1.401(a)(4)-3 - Nondiscrimination in amount of employer-provided benefits under a defined benefit plan.

Code of Federal Regulations, 2012 CFR

2012-04-01

... satisfies the ratio percentage test of § 1.410(b)-2(b)(2) because the ratio percentage of the rate group is... percent).) (g) Rate group 51 satisfies the ratio percentage test of § 1.410(b)-2(b)(2) because the ratio... uniform benefits are permitted to satisfy this requirement by meeting one of the safe harbors in paragraph...

26 CFR 1.401(a)(4)-3 - Nondiscrimination in amount of employer-provided benefits under a defined benefit plan.

Code of Federal Regulations, 2011 CFR

2011-04-01

... satisfies the ratio percentage test of § 1.410(b)-2(b)(2) because the ratio percentage of the rate group is... percent).) (g) Rate group 51 satisfies the ratio percentage test of § 1.410(b)-2(b)(2) because the ratio... uniform benefits are permitted to satisfy this requirement by meeting one of the safe harbors in paragraph...

26 CFR 1.401(a)(4)-3 - Nondiscrimination in amount of employer-provided benefits under a defined benefit plan.

Code of Federal Regulations, 2014 CFR

2014-04-01

... satisfies the ratio percentage test of § 1.410(b)-2(b)(2) because the ratio percentage of the rate group is... percent).) (g) Rate group 51 satisfies the ratio percentage test of § 1.410(b)-2(b)(2) because the ratio... uniform benefits are permitted to satisfy this requirement by meeting one of the safe harbors in paragraph...

The High Power Electric Propulsion (HiPEP) Ion Thruster

NASA Technical Reports Server (NTRS)

Foster, John E.; Haag, Tom; Patterson, Michael; Williams, George J., Jr.; Sovey, James S.; Carpenter, Christian; Kamhawi, Hani; Malone, Shane; Elliot, Fred

2004-01-01

Practical implementation of the proposed Jupiter Icy Moon Orbiter (JIMO) mission, which would require a total delta V of approximately 38 km/s, will require the development of a high power, high specific impulse propulsion system. Initial analyses show that high power gridded ion thrusters could satisfy JIMO mission requirements. A NASA GRC-led team is developing a large area, high specific impulse, nominally 25 kW ion thruster to satisfy both the performance and the lifetime requirements for this proposed mission. The design philosophy and development status as well as a thruster performance assessment are presented.

Towards a Scalable Group Vehicle-based Security System

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carter, Jason M

2016-01-01

In August 2014, the National Highway Traffic Safety Administration (NHTSA) proposed new rulemaking to require V2V communication in light vehicles. To establish trust in the basic safety messages (BSMs) that are exchanged by vehicles to improve driver safety, a vehicle public key infrastructure (VPKI) is required. We outline a system where a group or groups of vehicles manage and generate their own BSM signing keys and authenticating certificates -- a Vehicle-Based Security System (VBSS). Based on our preliminary examination, we assert the mechanisms exist to implement a VBSS that supports V2V communications; however, maintaining uniform trust throughout the system whilemore » protecting individual privacy does require reliance on nascent group signature technology which may require a significant amount of communication overhead for trust maintenance. To better evaluate the VBSS approach, we compare it to the proposed Security Credential Management System (SCMS) in four major areas including bootstrapping, pseudonym provisioning, BSM signing and authentication, and revocation. System scale, driver privacy, and the distribution and dynamics of participants make designing an effective VPKI an interesting and challenging problem; no clear-cut strategy exists to satisfy the security and privacy expectations in a highly efficient way. More work is needed in VPKI research, so the life-saving promise of V2V technology can be achieved.« less

A triangle voting algorithm based on double feature constraints for star sensors

NASA Astrophysics Data System (ADS)

Fan, Qiaoyun; Zhong, Xuyang

2018-02-01

A novel autonomous star identification algorithm is presented in this study. In the proposed algorithm, each sensor star constructs multi-triangle with its bright neighbor stars and obtains its candidates by triangle voting process, in which the triangle is considered as the basic voting element. In order to accelerate the speed of this algorithm and reduce the required memory for star database, feature extraction is carried out to reduce the dimension of triangles and each triangle is described by its base and height. During the identification period, the voting scheme based on double feature constraints is proposed to implement triangle voting. This scheme guarantees that only the catalog star satisfying two features can vote for the sensor star, which improves the robustness towards false stars. The simulation and real star image test demonstrate that compared with the other two algorithms, the proposed algorithm is more robust towards position noise, magnitude noise and false stars.

Control-structure interaction study for the Space Station solar dynamic power module

NASA Technical Reports Server (NTRS)

Cheng, J.; Ianculescu, G.; Ly, J.; Kim, M.

1991-01-01

The authors investigate the feasibility of using a conventional PID (proportional plus integral plus derivative) controller design to perform the pointing and tracking functions for the Space Station Freedom solar dynamic power module. Using this simple controller design, the control/structure interaction effects were also studied without assuming frequency bandwidth separation. From the results, the feasibility of a simple solar dynamic control solution with a reduced-order model, which satisfies the basic system pointing and stability requirements, is suggested. However, the conventional control design approach is shown to be very much influenced by the order of reduction of the plant model, i.e., the number of the retained elastic modes from the full-order model. This suggests that, for complex large space structures, such as the Space Station Freedom solar dynamic, the conventional control system design methods may not be adequate.

Théodule Ribot's ambiguous positivism: philosophical and epistemological strategies in the founding of French scientific psychology.

PubMed

Guillin, Vincent

2004-01-01

Théodule Ribot (1839-1916) is regarded by many historians of psychology as the "father" of the discipline in France. Ribot contributed to the development of a "new psychology" independent from philosophy, relying on the methods of the natural sciences. However, such an epistemological transition encountered fierce opposition from both the champions of the old-fashioned metaphysical psychology and the representatives of the "scientific spirit." This article focuses on the objections raised by the latter, and especially philosophers of science, against the possibility of a scientific psychology. For instance, according to Auguste Comte, psychology does not satisfy certain basic methodological requirements. To overcome these objections, Ribot, in his La Psychologie Anglaise Contemporaine (1870/1914), devised an epistemological strategy that amounted to invoking criticisms of Comte's views made by other representatives of the positivist school, such as John Stuart Mill and Herbert Spencer. Copyright 2004 Wiley Periodicals, Inc.

Electron lithography STAR design guidelines. Part 3: The mosaic transistor array applied to custom microprocessors. Part 4: Stores logic arrays, SLAs implemented with clocked CMOS

NASA Technical Reports Server (NTRS)

Trotter, J. D.

1982-01-01

The Mosaic Transistor Array is an extension of the STAR system developed by NASA which has dedicated field cells designed to be specifically used in semicustom microprocessor applications. The Sandia radiation hard bulk CMOS process is utilized in order to satisfy the requirements of space flights. A design philosophy is developed which utilizes the strengths and recognizes the weaknesses of the Sandia process. A style of circuitry is developed which incorporates the low power and high drive capability of CMOS. In addition the density achieved is better than that for classic CMOS, although not as good as for NMOS. The basic logic functions for a data path are designed with compatible interface to the STAR grid system. In this manner either random logic or PLA type structures can be utilized for the control logic.

Security Framework for Pervasive Healthcare Architectures Utilizing MPEG-21 IPMP Components.

PubMed

Fragopoulos, Anastasios; Gialelis, John; Serpanos, Dimitrios

2009-01-01

Nowadays in modern and ubiquitous computing environments, it is imperative more than ever the necessity for deployment of pervasive healthcare architectures into which the patient is the central point surrounded by different types of embedded and small computing devices, which measure sensitive physical indications, interacting with hospitals databases, allowing thus urgent medical response in occurrences of critical situations. Such environments must be developed satisfying the basic security requirements for real-time secure data communication, and protection of sensitive medical data and measurements, data integrity and confidentiality, and protection of the monitored patient's privacy. In this work, we argue that the MPEG-21 Intellectual Property Management and Protection (IPMP) components can be used in order to achieve protection of transmitted medical information and enhance patient's privacy, since there is selective and controlled access to medical data that sent toward the hospital's servers.

Program VSAERO theory document: A computer program for calculating nonlinear aerodynamic characteristics of arbitrary configurations

NASA Technical Reports Server (NTRS)

Maskew, Brian

1987-01-01

The VSAERO low order panel method formulation is described for the calculation of subsonic aerodynamic characteristics of general configurations. The method is based on piecewise constant doublet and source singularities. Two forms of the internal Dirichlet boundary condition are discussed and the source distribution is determined by the external Neumann boundary condition. A number of basic test cases are examined. Calculations are compared with higher order solutions for a number of cases. It is demonstrated that for comparable density of control points where the boundary conditions are satisfied, the low order method gives comparable accuracy to the higher order solutions. It is also shown that problems associated with some earlier low order panel methods, e.g., leakage in internal flows and junctions and also poor trailing edge solutions, do not appear for the present method. Further, the application of the Kutta conditions is extremely simple; no extra equation or trailing edge velocity point is required. The method has very low computing costs and this has made it practical for application to nonlinear problems requiring iterative solutions for wake shape and surface boundary layer effects.

xCT (SLC7A11)-mediated metabolic reprogramming promotes non-small cell lung cancer progression.

PubMed

Ji, Xiangming; Qian, Jun; Rahman, S M Jamshedur; Siska, Peter J; Zou, Yong; Harris, Bradford K; Hoeksema, Megan D; Trenary, Irina A; Heidi, Chen; Eisenberg, Rosana; Rathmell, Jeffrey C; Young, Jamey D; Massion, Pierre P

2018-05-23

Many tumors increase uptake and dependence on glucose, cystine or glutamine. These basic observations on cancer cell metabolism have opened multiple new diagnostic and therapeutic avenues in cancer research. Recent studies demonstrated that smoking could induce the expression of xCT (SLC7A11) in oral cancer cells, suggesting that overexpression of xCT may support lung tumor progression. We hypothesized that overexpression of xCT occurs in lung cancer cells to satisfy the metabolic requirements for growth and survival. Our results demonstrated that 1) xCT was highly expressed at the cytoplasmic membrane in non-small cell lung cancer (NSCLC), 2) the expression of xCT was correlated with advanced stage and predicted a worse 5-year survival, 3) targeting xCT transport activity in xCT overexpressing NSCLC cells with sulfasalazine decreased cell proliferation and invasion in vitro and in vivo and 4) increased dependence on glutamine was observed in xCT overexpressed normal airway epithelial cells. These results suggested that xCT regulate metabolic requirements during lung cancer progression and be a potential therapeutic target in NSCLC.

[Overall design and proof-test of an integrated environmental control and life support system (ECLSS) for demonstration and verification].

PubMed

Rui, Jia-bai; Zheng, Chuan-xian; Zeng, Qing-tang

2002-12-01

Objective. To test and demonstrate embryonic form of our future space station ECLSS, which will also form an advanced research and test ground facility. Method. The following functions of the system were tested and demonstrated: integrated solid amine CO2 collection and concentration, Sabatier CO2 reduction, urine processing thermoelectric integrated membrane evaporation, solid polymer water electrolysis O2 generation, concentrated ventilation, temperature and humidity control, the measurement and control system, and other non-regenerative techniques. All of these were demonstrated in a sealed adiabatic module, and passed the proof-tests. Result. The principal technical requirements of the system and each regenerative subsystem were met. The integration of system general and each subsystem was successful, and the partial closed loop of the system's integration has been realized basically. Conclusion. The reasonableness of the project design was verified, and the major system technical requirements were satisfied. The suitability and harmonization among system general and each subsystem were good, the system operated normally, and the parameters measured were correct.

Multistage Passive Cooler for Spaceborne Instruments

NASA Technical Reports Server (NTRS)

Rodriquez, Jose I.

2007-01-01

A document describes a three-stage passive radiative cooler for a cryogenic spectrometer to be launched into a low orbit around the Moon. This cooler is relatively lightweight and compact, and its basic design is scalable and otherwise adaptable to other applications in which there are requirements for cooling instrumentation in orbit about planets. The cooler includes multiple lightweight flat radiator blades alternating with cylindrical parabolic infrared reflectors. The radiator blades are oriented at an angle chosen to prevent infrared loading from the Moon limb at the intended orbital altitude and attitude. The reflectors are shaped and oriented to position their foci outside the radiator surfaces. There are six radiator-blade/reflector pairs - two pairs for each stage of cooling. The radiator blades and reflectors are coated on their front and back surfaces with materials having various infrared emissivities, infrared reflectivities, and solar reflectivities so as to maximize infrared radiation to cold outer space and minimize inadvertent solar heating. The radiator blades and reflectors are held in place by a lightweight support structure, the components of which are designed to satisfy a complex combination of thermal and mechanical requirements.

Design control for clinical translation of 3D printed modular scaffolds.

PubMed

Hollister, Scott J; Flanagan, Colleen L; Zopf, David A; Morrison, Robert J; Nasser, Hassan; Patel, Janki J; Ebramzadeh, Edward; Sangiorgio, Sophia N; Wheeler, Matthew B; Green, Glenn E

2015-03-01

The primary thrust of tissue engineering is the clinical translation of scaffolds and/or biologics to reconstruct tissue defects. Despite this thrust, clinical translation of tissue engineering therapies from academic research has been minimal in the 27 year history of tissue engineering. Academic research by its nature focuses on, and rewards, initial discovery of new phenomena and technologies in the basic research model, with a view towards generality. Translation, however, by its nature must be directed at specific clinical targets, also denoted as indications, with associated regulatory requirements. These regulatory requirements, especially design control, require that the clinical indication be precisely defined a priori, unlike most academic basic tissue engineering research where the research target is typically open-ended, and furthermore requires that the tissue engineering therapy be constructed according to design inputs that ensure it treats or mitigates the clinical indication. Finally, regulatory approval dictates that the constructed system be verified, i.e., proven that it meets the design inputs, and validated, i.e., that by meeting the design inputs the therapy will address the clinical indication. Satisfying design control requires (1) a system of integrated technologies (scaffolds, materials, biologics), ideally based on a fundamental platform, as compared to focus on a single technology, (2) testing of design hypotheses to validate system performance as opposed to mechanistic hypotheses of natural phenomena, and (3) sequential testing using in vitro, in vivo, large preclinical and eventually clinical tests against competing therapies, as compared to single experiments to test new technologies or test mechanistic hypotheses. Our goal in this paper is to illustrate how design control may be implemented in academic translation of scaffold based tissue engineering therapies. Specifically, we propose to (1) demonstrate a modular platform approach founded on 3D printing for developing tissue engineering therapies and (2) illustrate the design control process for modular implementation of two scaffold based tissue engineering therapies: airway reconstruction and bone tissue engineering based spine fusion.

Design Control for Clinical Translation of 3D Printed Modular Scaffolds

PubMed Central

Hollister, Scott J.; Flanagan, Colleen L.; Zopf, David A.; Morrison, Robert J.; Nasser, Hassan; Patel, Janki J.; Ebramzadeh, Edward; Sangiorgio, Sophia N.; Wheeler, Matthew B.; Green, Glenn E.

2015-01-01

The primary thrust of tissue engineering is the clinical translation of scaffolds and/or biologics to reconstruct tissue defects. Despite this thrust, clinical translation of tissue engineering therapies from academic research has been minimal in the 27 year history of tissue engineering. Academic research by its nature focuses on, and rewards, initial discovery of new phenomena and technologies in the basic research model, with a view towards generality. Translation, however, by its nature must be directed at specific clinical targets, also denoted as indications, with associated regulatory requirements. These regulatory requirements, especially design control, require that the clinical indication be precisely defined a priori, unlike most academic basic tissue engineering research where the research target is typically open-ended, and furthermore requires that the tissue engineering therapy be constructed according to design inputs that ensure it treats or mitigates the clinical indication. Finally, regulatory approval dictates that the constructed system be verified, i.e., proven that it meets the design inputs, and validated, i.e., that by meeting the design inputs the therapy will address the clinical indication. Satisfying design control requires (1) a system of integrated technologies (scaffolds, materials, biologics), ideally based on a fundamental platform, as compared to focus on a single technology, (2) testing of design hypotheses to validate system performance as opposed to mechanistic hypotheses of natural phenomena, and (3) sequential testing using in vitro, in vivo, large preclinical and eventually clinical tests against competing therapies, as compared to single experiments to test new technologies or test mechanistic hypotheses. Our goal in this paper is to illustrate how design control may be implemented in academic translation of scaffold based tissue engineering therapies. Specifically, we propose to (1) demonstrate a modular platform approach founded on 3D printing for developing tissue engineering therapies and (2) illustrate the design control process for modular implementation of two scaffold based tissue engineering therapies: airway reconstruction and bone tissue engineering based spine fusion. PMID:25666115

39 CFR 762.42 - Request for substitute disbursement postal money orders; requirements for undertaking of indemnity.

Code of Federal Regulations, 2011 CFR

2011-07-01

... the following classes of cases: (1) If the Postal Service is satisfied that the loss, theft... Service is satisfied as to the identity of the Disbursement Postal Money Order presented and that any...

39 CFR 762.42 - Request for substitute disbursement postal money orders; requirements for undertaking of indemnity.

Code of Federal Regulations, 2010 CFR

2010-07-01

... the following classes of cases: (1) If the Postal Service is satisfied that the loss, theft... Service is satisfied as to the identity of the Disbursement Postal Money Order presented and that any...

An analytical study of double bend achromat lattice.

PubMed

Fakhri, Ali Akbar; Kant, Pradeep; Singh, Gurnam; Ghodke, A D

2015-03-01

In a double bend achromat, Chasman-Green (CG) lattice represents the basic structure for low emittance synchrotron radiation sources. In the basic structure of CG lattice single focussing quadrupole (QF) magnet is used to form an achromat. In this paper, this CG lattice is discussed and an analytical relation is presented, showing the limitation of basic CG lattice to provide the theoretical minimum beam emittance in achromatic condition. To satisfy theoretical minimum beam emittance parameters, achromat having two, three, and four quadrupole structures is presented. In this structure, different arrangements of QF and defocusing quadruple (QD) are used. An analytical approach assuming quadrupoles as thin lenses has been followed for studying these structures. A study of Indus-2 lattice in which QF-QD-QF configuration in the achromat part has been adopted is also presented.

26 CFR 1.401(a)(4)-3 - Nondiscrimination in amount of employer-provided benefits under a defined benefit plan.

Code of Federal Regulations, 2010 CFR

2010-04-01

... satisfies the ratio percentage test of § 1.410(b)-2(b)(2) because the ratio percentage of the rate group is... percent).) (g) Rate group 51 satisfies the ratio percentage test of § 1.410(b)-2(b)(2) because the ratio... benefits are permitted to satisfy this requirement by meeting one of the safe harbors in paragraph (b) of...

Micromechanical Disk Array for Enhanced Frequency Stability Against Bias Voltage Fluctuations

DTIC Science & Technology

2014-11-20

already made inroads into the low-end timing market , and research devices have been reported to satisfy GSM phase noise requirements while only...resonators have already made inroads into the low-end timing market , and research devices have been reported to satisfy GSM phase noise requirements...Notably oscillators referenced to very high Q capacitive-gap transduced MEMS resonators have already made inroads into the low-end timing market , and

Two proposed convergence criteria for Monte Carlo solutions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Forster, R.A.; Pederson, S.P.; Booth, T.E.

1992-01-01

The central limit theorem (CLT) can be applied to a Monte Carlo solution if two requirements are satisfied: (1) The random variable has a finite mean and a finite variance; and (2) the number N of independent observations grows large. When these two conditions are satisfied, a confidence interval (CI) based on the normal distribution with a specified coverage probability can be formed. The first requirement is generally satisfied by the knowledge of the Monte Carlo tally being used. The Monte Carlo practitioner has a limited number of marginal methods to assess the fulfillment of the second requirement, such asmore » statistical error reduction proportional to 1/[radical]N with error magnitude guidelines. Two proposed methods are discussed in this paper to assist in deciding if N is large enough: estimating the relative variance of the variance (VOV) and examining the empirical history score probability density function (pdf).« less

Investigating Students' Perceived Discipline Relevance Subsequent to Playing Educational Computer Games: A Personal Interest and Self-Determination Theory Approach

ERIC Educational Resources Information Center

Sorebo, Oystein; Haehre, Reidar

2012-01-01

The purpose of this study is to explain students' perceived relevance of playing an educational game as a means for development of discipline competence. Based on self-determination theory and the concept of personal interest, we propose that: Satisfying students' basic needs for competence, autonomy, and relatedness when playing educational games…

Money Buys Financial Security and Psychological Need Satisfaction: Testing Need Theory in Affluence

ERIC Educational Resources Information Center

Howell, Ryan T.; Kurai, Mark; Tam, Leona

2013-01-01

The most prominent theory to explain the curvilinear relationship between income and subjective well-being (SWB) is need theory, which proposes that increased income and wealth can lead to increased well-being in poverty because money is used to satisfy basic physiological needs. The present study tests the tenets of need theory by proposing that…

Terrestrial quarantine considerations for unmanned sample return missions

NASA Technical Reports Server (NTRS)

Hoffman, A. R.; Stavro, W.; Miller, L. W.; Taylor, D. M.

1973-01-01

For the purpose of understanding some of the possible implications of a terrestrial quarantine constraint on a mission and for developing a basic approach which can be used to demonstrate compliance beyond that developed for Apollo, a terrestrial quarantine study was performed. It is shown that some of the basic tools developed and used by the planetary quarantine community have applicability to terrestrial quarantine analysis. By using these tools, it is concluded that: (1) the method of biasing the earth aiming point when returning from the planet is necessary but, by itself, may not satisfy terrestrial quarantine constraints; and (2) spacecraft and container design significantly influence contamination transfer.

Fractional vector calculus and fluid mechanics

NASA Astrophysics Data System (ADS)

Lazopoulos, Konstantinos A.; Lazopoulos, Anastasios K.

2017-04-01

Basic fluid mechanics equations are studied and revised under the prism of fractional continuum mechanics (FCM), a very promising research field that satisfies both experimental and theoretical demands. The geometry of the fractional differential has been clarified corrected and the geometry of the fractional tangent spaces of a manifold has been studied in Lazopoulos and Lazopoulos (Lazopoulos KA, Lazopoulos AK. Progr. Fract. Differ. Appl. 2016, 2, 85-104), providing the bases of the missing fractional differential geometry. Therefore, a lot can be contributed to fractional hydrodynamics: the basic fractional fluid equations (Navier Stokes, Euler and Bernoulli) are derived and fractional Darcy's flow in porous media is studied.

Low cost miniature data collection platform

NASA Technical Reports Server (NTRS)

1977-01-01

The development of the RF elements of a telecommunications package involved detailed study and analysis of concepts and techniques followed by laboratory testing and evaluation of designs. The design goals for a complete telecommunications package excluding antenna were a total weight of 300 grams, in a total volume of 400 cu cm with a capability of unattended operation for a period of six months. Of utmost importance is extremely low cost when produced in lots of 10,000. Early in the program it became apparent that a single Miniature Data Collection Platform would not satisfy all users. A single high efficiency system would not satisfy a user who had available a large battery capacity but required a low cost system. Conversely, the low cost system would not satisfy the end user who had a very limited battery capacity. A system design to satisfy these varied requirements was implemented by designing several versions of the system building blocks and then constructing three systems from these building blocks.

Light Pollution: A Primer for Astronomers to Engage in Teaching and Outreach

NASA Astrophysics Data System (ADS)

Caton, Daniel Bruce

2018-01-01

Most astronomers are familiar with the basic problem of light pollution but may not have explored how to teach their students about the problem or to inform officials in their community in order to help mitigate the problem. Indeed, many professional and amateur astronomers leave their light-polluted community to observe the sky from dark research observatories and rural star parties,, and then return to take no action to alleviate and reduce the light pollution in their own community. This is not a sustainable approach, and eventually this will lead to fewer sites to do their observations.In this presentation we give the basics of the problem and provide information on effective solutions. A link will be provided to download a sample PowerPoint, with Notes providing guidance to edit it to include images of both good and bad lighting in their own community. This can be shown to students as part of introductory astronomy and observational techniques courses, so the students might be able to help their with the problem in their own communities. Indeed this may satisfy curriculum requirements as a component of sustainable development. It may also be presented to local planning and permitting officials to develop at least a simple outdoor lighting ordinance.

A team public health research project for first-year pharmacy students to apply content from didactic courses.

PubMed

Fuentes, David; Deguire, Nancy; Patel, Rajul; Boyce, Eric

2010-08-10

To implement and assess a first-year pharmacy student group research project that provided practical hands-on application and reinforced the curricula of concurrent didactic courses. Groups of 6 to 7 students chose a public health topic based on the Healthy People 2010 Priority Areas and created a survey instrument. Faculty facilitated mock institutional review board (IRB) review sessions which provided teams with ongoing feedback and refinement recommendations before each team administered their survey instrument to a predefined population. Data analysis, formal written reports, and oral presentations were presented to peers and project faculty members. Teams complied with the requirements of the mock IRB, effectively applied basic research principles learned in class, collected survey data, performed inferential statistical analyses on the data, , and presented their project findings. Two-hundred six of 210 students (98%) reported feeling satisfied with both the results of their project and the accomplishments of their team. Teams applied a varied skill set including primary literature evaluation, basic research principles, statistics, public speaking, and peer collaboration in conducting a public health research project. First-year pharmacy students may benefit from participation in a collaborative research project that provides hands-on application of material being taught in didactic courses.

Career management: understanding the process.

PubMed

Mackowiak, J; Eckel, F M

1985-02-01

This article is the first of a three-part series on career management for hospital pharmacists. Work attitudes, life cycles, needs, and career trends are discussed. Three basic work attitudes exist. Some see work as punishment. Others believe work in itself is good, i.e., they have a strong work ethic. Some view work as a means to satisfy, at least partially, a range of needs. Attitudinal transition points are likely to occur at specific times in the adult life cycle. The stages of the life cycle can be labeled as leaving, reaching out, questioning, midlife crisis, settling down, and mellowing. A progression through each of these stages is required for normal adult psychological development. Every individual exhibits a blend of needs that changes throughout life. Jobs can fulfill existence, relatedness, and growth needs. Relatedness needs include the need for love, affiliation, social esteem, and power, and growth needs include the need for self-esteem, competence, achievement, and autonomy. Three important career trends are the changing opportunities for advancement, women in careers, and dual-career couples. The number of women pharmacists is increasing as is the number of two-career couples. Tips for managing two-career relationships are presented. Pharmacists can manage their careers more effectively by understanding their needs, identifying their basic attitude toward work, and being aware of the trends occurring in pharmacy.

Ant Colony Optimization Analysis on Overall Stability of High Arch Dam Basis of Field Monitoring

PubMed Central

Liu, Xiaoli; Chen, Hong-Xin; Kim, Jinxie

2014-01-01

A dam ant colony optimization (D-ACO) analysis of the overall stability of high arch dams on complicated foundations is presented in this paper. A modified ant colony optimization (ACO) model is proposed for obtaining dam concrete and rock mechanical parameters. A typical dam parameter feedback problem is proposed for nonlinear back-analysis numerical model based on field monitoring deformation and ACO. The basic principle of the proposed model is the establishment of the objective function of optimizing real concrete and rock mechanical parameter. The feedback analysis is then implemented with a modified ant colony algorithm. The algorithm performance is satisfactory, and the accuracy is verified. The m groups of feedback parameters, used to run a nonlinear FEM code, and the displacement and stress distribution are discussed. A feedback analysis of the deformation of the Lijiaxia arch dam and based on the modified ant colony optimization method is also conducted. By considering various material parameters obtained using different analysis methods, comparative analyses were conducted on dam displacements, stress distribution characteristics, and overall dam stability. The comparison results show that the proposal model can effectively solve for feedback multiple parameters of dam concrete and rock material and basically satisfy assessment requirements for geotechnical structural engineering discipline. PMID:25025089

77 FR 24555 - Andean Trade Preference Act (ATPA), as Amended: Request for Public Comments Regarding Beneficiary...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-24

...., provides trade benefits for eligible Andean countries. The original Act allowed only Bolivia, Ecuador... Bolivia no longer satisfies the eligibility criteria related to counternarcotics and suspended Bolivia's... Congress, the President did not determine that Bolivia satisfies the requirements set forth in section 203...

77 FR 64890 - Transmission Planning and Cost Allocation by Transmission Owning and Operating Public Utilities

Federal Register 2010, 2011, 2012, 2013, 2014

2012-10-24

... each cost allocation method must satisfy six cost allocation principles. DATES: Effective November 23... Interregional Transmission 61 Coordination Requirements III. Cost Allocation 65 1. Cost Allocation Principle 2... must satisfy six cost allocation principles. 3. In Order No. 1000-A, the Commission largely affirmed...

41 CFR 60-741.3 - Exceptions to the definitions of “disability” and “qualified individual.”

Code of Federal Regulations, 2014 CFR

2014-07-01

... individual satisfies the requisite skill, experience, education, and other job-related requirements of such... individual, provided that such individual satisfies the requisite skill, experience, education, and other job..., voyeurism, gender identity disorders not resulting from physical impairments, or other sexual behavior...

43 CFR 419.1 - What is the purpose of this part?

Code of Federal Regulations, 2014 CFR

2014-10-01

... Truckee River Reservoirs to satisfy the exercise of water rights in conformance with the Orr Ditch Decree...) This part satisfies the requirement of Section 205(a)(5) of the Truckee-Carson-Pyramid Lake Water...: (1) Implements California's allocation of Truckee River basin water and the Nevada and California...

43 CFR 419.1 - What is the purpose of this part?

Code of Federal Regulations, 2013 CFR

2013-10-01

... Truckee River Reservoirs to satisfy the exercise of water rights in conformance with the Orr Ditch Decree...) This part satisfies the requirement of Section 205(a)(5) of the Truckee-Carson-Pyramid Lake Water...: (1) Implements California's allocation of Truckee River basin water and the Nevada and California...

43 CFR 419.1 - What is the purpose of this part?

Code of Federal Regulations, 2012 CFR

2012-10-01

... Truckee River Reservoirs to satisfy the exercise of water rights in conformance with the Orr Ditch Decree...) This part satisfies the requirement of Section 205(a)(5) of the Truckee-Carson-Pyramid Lake Water...: (1) Implements California's allocation of Truckee River basin water and the Nevada and California...

40 CFR 62.14463 - What reporting requirements must I satisfy?

Code of Federal Regulations, 2014 CFR

2014-07-01

... must I satisfy? (a) You must report the following to the EPA Administrator (or delegated enforcement... 10 days of an inspection or the time frame established by the EPA Administrator (or delegated... EPA Administrator (or delegated enforcement authority); (14) Concentrations of CO, PM, HCl, Pb, Cd, Hg...

40 CFR 62.14463 - What reporting requirements must I satisfy?

Code of Federal Regulations, 2013 CFR

2013-07-01

... must I satisfy? (a) You must report the following to the EPA Administrator (or delegated enforcement... 10 days of an inspection or the time frame established by the EPA Administrator (or delegated... EPA Administrator (or delegated enforcement authority); (14) Concentrations of CO, PM, HCl, Pb, Cd, Hg...

Afghanistan in the Balance: Air Politik

DTIC Science & Technology

2010-06-01

satisfying basic physiological needs, such as food and water; then safety; love and belonging, esteem , and self -actualization. 17 In a contemporary...Instead, through an understanding of shared self -interests, states produce norms and standards of behavior that can be temporally enabling but are also...regime guided by the principles of the Peace of Westphalia (1648). This standard acknowledges the right of a state to self -determination. In this

[Development of special food products for cosmonaut's nutrition during extravehicular activities].

PubMed

Agureev, A N; Kalandarov, S; Vasil'eva, V F; Gurova, L A

2003-01-01

On the analysis of the factual energy expenditure by cosmonauts during extravehicular activities two choices of special rations (SR) were developed. Hygienic testing showed that all nutritional components in these SRs were present in optimal quantities. Consumption of the SR foods during any basic meal will not misbalance the latter but satisfy the body demand of the main indispensable nutritional factors.

An iwatsubo-based solution for labyrinth seals - comparison with experimental results

NASA Technical Reports Server (NTRS)

Childs, D. W.; Scharrer, J. K.

1984-01-01

The basic equations are derived for compressible flow in a labyrinth seal. The flow is assumed to be completely turbulent in the circumferential direction where the friction factor is determined by the Blasius relation. Linearized zeroth and first-order perturbation equations are developed for small motion about a centered position by an expansion in the eccentricity ratio. The zeroth-order pressure distribution is found by satisfying the leakage equation while the circumferential velocity distribution is determined by satisfying the momentum equation. The first-order equations are solved by a separation of variables solution. Integration of the resultant pressure distribution along and around the seal defines the reaction force developed by the seal and the corresponding dynamic coefficients. The results of this analysis are compared to published test results.

Fractional Klein-Gordon equation composed of Jumarie fractional derivative and its interpretation by a smoothness parameter

NASA Astrophysics Data System (ADS)

Ghosh, Uttam; Banerjee, Joydip; Sarkar, Susmita; Das, Shantanu

2018-06-01

Klein-Gordon equation is one of the basic steps towards relativistic quantum mechanics. In this paper, we have formulated fractional Klein-Gordon equation via Jumarie fractional derivative and found two types of solutions. Zero-mass solution satisfies photon criteria and non-zero mass satisfies general theory of relativity. Further, we have developed rest mass condition which leads us to the concept of hidden wave. Classical Klein-Gordon equation fails to explain a chargeless system as well as a single-particle system. Using the fractional Klein-Gordon equation, we can overcome the problem. The fractional Klein-Gordon equation also leads to the smoothness parameter which is the measurement of the bumpiness of space. Here, by using this smoothness parameter, we have defined and interpreted the various cases.

Minimization of Food Cost on 2000-Calorie Diabetic Diet

NASA Astrophysics Data System (ADS)

Urrutia, J. D.; Mercado, J.; Tampis, R. L.

2017-03-01

This study focuses on minimization of food cost that satisfies the daily nutrients required based on 2000-calorie diet for a diabetic person. This paper attempts to provide a food combination that satisfies the daily nutrient requirements of a diabetic person and its lowest possible dietary food cost. A linear programming diet model is used to determine the cheapest combination of food items that satisfy the recommended daily nutritional requirements of the diabetic persons. According to the findings, a 50 year old and above diabetic male need to spend a minimum of 72.22 pesos for foods that satisfy the daily nutrients they need. In order to attain the minimum spending, the foods must consist of 60.49 grams of anchovy, 91.24 grams of carrot, 121.92 grams of durian, 121.41 grams of chicken egg, 70.82 grams of pork (lean), and 369.70 grams of rice (well-milled). For a 50 year old and above diabetic female, the minimum spending is 64.65 pesos per day and the food must consist of 75.87 grams of anchovy, 43.38 grams of carrot, 160.46 grams of durian, 69.66 grams of chicken egg, 23.16 grams of pork (lean) and 416.19 grams of rice (well-milled).

Micromachined TWTs for THz Radiation Sources

NASA Technical Reports Server (NTRS)

Booske, John H.; vanderWeide, Daniel W.; Kory, Carol L.; Limbach, S.; Downey, Alan (Technical Monitor)

2001-01-01

The Terahertz (THz) region of the electromagnetic spectrum (about 300 - 3000 GHz in frequency or about 0.1 - 1 mm free space wavelength) has enormous potential for high-data-rate communications, spectroscopy, astronomy, space research, medicine, biology, surveillance, remote sensing, industrial process control, etc. It has been characterized as the most scientifically rich, yet under-utilized, region of the electromagnetic spectrum. The most critical roadblock to full exploitation of the THz band is lack of coherent radiation sources that are powerful (0.001 - 1.0 W continuous wave), efficient (> 1%), frequency agile (instantaneously tunable over 1% bandwidths or more), reliable, and comparatively inexpensive. To develop vacuum electron device (VED) radiation sources satisfying these requirements, fabrication and packaging approaches must be heavily considered to minimize costs, in addition to the basic interaction physics and circuit design. To minimize size of the prime power supply, beam voltage must be minimized, preferably 10 kV. Solid state sources satisfy the low voltage requirement, but are many orders of magnitude below power, efficiency, and bandwidth requirements. On the other hand, typical fast-wave VED sources in this regime (e.g., gyrotrons, FELs) tend to be large, expensive, high voltage and very high power devices unsuitable for most of the applications cited above. VEDs based on grating or inter-digital (ID) circuits have been researched and developed. However, achieving forward-wave amplifier operation with instantaneous fractional bandwidths > 1% is problematic for these devices with low-energy (< 15 kV) electron beams. Moreover, the interaction impedance is quite low unless the beam-circuit spacing is kept particularly narrow, often leading to significant beam interception. One solution to satisfy the THz source requirements mentioned above is to develop micromachined VEDs, or "micro-VEDs". Among other benefits, micro-machining technologies provide superior high frequency wall conductivity as a result of superior surface smoothness compared with conventional mechanical or electric discharge machining approaches. Micro-VED technologies are already being applied to the development of millimeter-wave klystrons at Stanford Linear Accelerator Center and submillimeter-wave klystrons at the University of Leeds. We are investigating the use of micro-machining technologies to develop THz regime TWTs, with emphasis on folded-waveguide TWTs. The folded-waveguide TWT (FW-TWT) has several features that make it attractive for THz-regime micro-VED applications. It is a relatively simple circuit to design and fabricate, it is amenable to precision pattern replication by micro-machining, and it is has been demonstrated capable of forward-wave amplification with appreciable bandwidth. We are conducting experimental and computational studies of micro-VED FW-TWTs to examine their feasibility for applications at frequencies from 200 - 1000 GHz.

Regulatory experience in applying a radiological environmental protection framework for existing and planned nuclear facilities.

PubMed

Mihok, S; Thompson, P

2012-01-01

Frameworks and methods for the radiological protection of non-human biota have been evolving rapidly at the International Commission on Radiological Protection and through various European initiatives. The International Atomic Energy Agency has incorporated a requirement for environmental protection in the latest revision of its Basic Safety Standards. In Canada, the Canadian Nuclear Safety Commission has been legally obligated to prevent unreasonable risk to the environment since 2000. Licensees have therefore been meeting generic legal requirements to demonstrate adequate control of releases of radioactive substances for the protection of both people and biota for many years. In the USA, in addition to the generic requirements of the Environmental Protection Agency and the Nuclear Regulatory Commission, Department of Energy facilities have also had to comply with specific dose limits after a standard assessment methodology was finalised in 2002. Canadian regulators developed a similar framework for biota dose assessment through a regulatory assessment under the Canadian Environmental Protection Act in the late 1990s. Since then, this framework has been applied extensively to satisfy legal requirements under the Canadian Environmental Assessment Act and the Nuclear Safety and Control Act. After approximately a decade of experience in applying these methods, it is clear that simple methods are fit for purpose, and can be used for making regulatory decisions for existing and planned nuclear facilities. Copyright © 2012. Published by Elsevier Ltd.

How to encourage intrinsic motivation in the clinical teaching environment?: a systematic review from the self-determination theory.

PubMed

Orsini, Cesar; Evans, Phillip; Jerez, Oscar

2015-01-01

Internalization of students' motivation towards an intrinsic form is associated with increased interest, commitment, learning, and satisfaction with education. Self-Determination theory postulates that intrinsic motivation and autonomous forms of self-regulation are the desired type of motivation; as they have been associated with deep learning, better performance and well-being. It claims three basic psychological needs have to be satisfied in order to achieve intrinsic motivation. These are the needs for autonomy, competence and relatedness. This study aims to provide a review on how these basic psychological needs are encouraged in undergraduate students so they can be transferred to the clinical teaching environment. Electronic searches were performed across four databases (Medline, Embase, PsycINFO, and ERIC), relevant journals, and retrieved bibliography of selected articles. In total, searches produced 4,869 references, from which 16 studies met the inclusion criteria. Main themes were coded in three categories: The support of autonomy, competence and relatedness. The research-based evidence appears to be of reasonable quality, and indicates that teachers should work to satisfy students' basic psychological needs to foster internalization of self-regulation. Our findings suggest that teachers should interact with students in a more 'human centred' teaching style, as these actions predict motivational internalization. Several themes emerged from different contexts and further investigation should expand them. This review identified actions that clinical teachers could implement in their daily work to support students' self-determination. Autonomy supportive teaching in health professions educations would benefit students and may actually result in more effective health care delivery.

How to encourage intrinsic motivation in the clinical teaching environment?: a systematic review from the self-determination theory

PubMed Central

2015-01-01

Purpose: Internalization of students’ motivation towards an intrinsic form is associated with increased interest, commitment, learning, and satisfaction with education. Self-Determination theory postulates that intrinsic motivation and autonomous forms of self-regulation are the desired type of motivation; as they have been associated with deep learning, better performance and well-being. It claims three basic psychological needs have to be satisfied in order to achieve intrinsic motivation. These are the needs for autonomy, competence and relatedness. This study aims to provide a review on how these basic psychological needs are encouraged in undergraduate students so they can be transferred to the clinical teaching environment. Methods: Electronic searches were performed across four databases (Medline, Embase, PsycINFO, and ERIC), relevant journals, and retrieved bibliography of selected articles. In total, searches produced 4,869 references, from which 16 studies met the inclusion criteria. Results: Main themes were coded in three categories: The support of autonomy, competence and relatedness. The research-based evidence appears to be of reasonable quality, and indicates that teachers should work to satisfy students’ basic psychological needs to foster internalization of self-regulation. Our findings suggest that teachers should interact with students in a more ‘human centred’ teaching style, as these actions predict motivational internalization. Several themes emerged from different contexts and further investigation should expand them. Conclusion: This review identified actions that clinical teachers could implement in their daily work to support students’ self-determination. Autonomy supportive teaching in health professions educations would benefit students and may actually result in more effective health care delivery. PMID:25855386

Some important considerations in the development of stress corrosion cracking test methods.

NASA Technical Reports Server (NTRS)

Wei, R. P.; Novak, S. R.; Williams, D. P.

1972-01-01

Discussion of some of the precaution needs the development of fracture-mechanics based test methods for studying stress corrosion cracking involves. Following a review of pertinent analytical fracture mechanics considerations and of basic test methods, the implications for test corrosion cracking studies of the time-to-failure determining kinetics of crack growth and life are examined. It is shown that the basic assumption of the linear-elastic fracture mechanics analyses must be clearly recognized and satisfied in experimentation and that the effects of incubation and nonsteady-state crack growth must also be properly taken into account in determining the crack growth kinetics, if valid data are to be obtained from fracture-mechanics based test methods.

Description of MSFC engineering photographic analysis

NASA Technical Reports Server (NTRS)

Earle, Jim; Williams, Frank

1988-01-01

Utilizing a background that includes development of basic launch and test photographic coverage and analysis procedures, the MSFC Photographic Evaluation Group has built a body of experience that enables it to effectively satisfy MSFC's engineering photographic analysis needs. Combining the basic soundness of reliable, proven techniques of the past with the newer technical advances of computers and computer-related devices, the MSFC Photo Evaluation Group is in a position to continue to provide photo and video analysis service center-wide and NASA-wide to supply an improving photo analysis product to meet the photo evaluation needs of the future; and to provide new standards in the state-of-the-art of photo analysis of dynamic events.

A quantitative analysis of inter-island telephony traffic in the Pacific Basin Region (PBR)

NASA Technical Reports Server (NTRS)

Evans, D. D.; Arth, C. H.

1980-01-01

As part of NASA's continuing assessment of future communication satellite requirements, a study was conducted to quantitatively scope current and future telecommunication traffic demand in the South Pacific Archipelagos. This demand was then converted to equivalent satellite transponder capacities. Only inter-island telephony traffic for the Pacific Basin Region was included. The results show that if all this traffic were carried by a satellite system, one-third of a satellite transponder would be needed to satisfy the base-year (1976-1977) requirement and about two-thirds of a satellite transponder would be needed to satisfy the forecasted 1985 requirement.

Discrete shaped strain sensors for intelligent structures

NASA Technical Reports Server (NTRS)

Andersson, Mark S.; Crawley, Edward F.

1992-01-01

Design of discrete, highly distributed sensor systems for intelligent structures has been studied. Data obtained indicate that discrete strain-averaging sensors satisfy the functional requirements for distributed sensing of intelligent structures. Bartlett and Gauss-Hanning sensors, in particular, provide good wavenumber characteristics while meeting the functional requirements. They are characterized by good rolloff rates and positive Fourier transforms for all wavenumbers. For the numerical integration schemes, Simpson's rule is considered to be very simple to implement and consistently provides accurate results for five sensors or more. It is shown that a sensor system that satisfies the functional requirements can be applied to a structure that supports mode shapes with purely sinusoidal curvature.

SNAP 19 Pioneer F and G. Final Report

DOE R&D Accomplishments Database

1973-06-01

The generator developed for the Pioneer mission evolved from the SNAP 19 RTG`s launched aboard the NIMBUS III spacecraft. In order to satisfy the power requirements and environment of earth escape trajectory, significant modifications were made to the thermoelectric converter, heat source, and structural configuration. Specifically, a TAGS 2N thermoelectric couple was designed to provide higher efficiency and improved long term power performance, and the electrical circuitry was modified to yield very low magnetic field from current flow in the RTG. A new heat source was employed to satisfy operational requirements and its integration with the generator required alteration to the method of providing support to the fuel capsule.

Leading Commercial Series Don't Satisfy "Gold Standard"

ERIC Educational Resources Information Center

Manzo, Kathleen Kennedy

2004-01-01

This article describes how despite the fact that a number of reading programs have satisfied the requirement under the federal reading law for embodying a strong research base, there appeared a limited outside evidence that any of them has produced a conclusive and consistent effect on overall reading achievement. The publishers of each of the…

43 CFR 419.3 - What general principles govern implementation of the TROA?

Code of Federal Regulations, 2013 CFR

2013-10-01

... the extent that water is lawfully available. This includes, but is not limited to, the exercise of... requirements, so that the available water supply in the Truckee River basin satisfies, to the maximum extent..., water quality, and recreation purposes. (b) Satisfy vested and perfected rights to use the water of the...

43 CFR 419.3 - What general principles govern implementation of the TROA?

Code of Federal Regulations, 2014 CFR

2014-10-01

... the extent that water is lawfully available. This includes, but is not limited to, the exercise of... requirements, so that the available water supply in the Truckee River basin satisfies, to the maximum extent..., water quality, and recreation purposes. (b) Satisfy vested and perfected rights to use the water of the...

43 CFR 419.3 - What general principles govern implementation of the TROA?

Code of Federal Regulations, 2012 CFR

2012-10-01

... the extent that water is lawfully available. This includes, but is not limited to, the exercise of... requirements, so that the available water supply in the Truckee River basin satisfies, to the maximum extent..., water quality, and recreation purposes. (b) Satisfy vested and perfected rights to use the water of the...

46 CFR 32.70-5 - Hull requirements; general-TB/ALL.

Code of Federal Regulations, 2013 CFR

2013-10-01

..., AND HULL REQUIREMENTS Hull Requirements for Steel Hull Tank Vessels Constructed Prior to November 10... Charge, Marine Inspection, shall satisfy himself that the vessel's structure as specified in this section...

46 CFR 32.70-5 - Hull requirements; general-TB/ALL.

Code of Federal Regulations, 2012 CFR

2012-10-01

..., AND HULL REQUIREMENTS Hull Requirements for Steel Hull Tank Vessels Constructed Prior to November 10... Charge, Marine Inspection, shall satisfy himself that the vessel's structure as specified in this section...

46 CFR 32.70-5 - Hull requirements; general-TB/ALL.

Code of Federal Regulations, 2014 CFR

2014-10-01

..., AND HULL REQUIREMENTS Hull Requirements for Steel Hull Tank Vessels Constructed Prior to November 10... Charge, Marine Inspection, shall satisfy himself that the vessel's structure as specified in this section...

46 CFR 32.70-5 - Hull requirements; general-TB/ALL.

Code of Federal Regulations, 2011 CFR

2011-10-01

..., AND HULL REQUIREMENTS Hull Requirements for Steel Hull Tank Vessels Constructed Prior to November 10... Charge, Marine Inspection, shall satisfy himself that the vessel's structure as specified in this section...

Characteristics of physicians engaged in basic science: a questionnaire survey of physicians in basic science departments of a medical school in Japan.

PubMed

Yamazaki, Yuka; Uka, Takanori; Shimizu, Haruhiko; Miyahira, Akira; Sakai, Tatsuo; Marui, Eiji

2012-09-01

The number of physicians engaged in basic science and teaching is sharply decreasing in Japan. To alleviate this shortage, central government has increased the quota of medical students entering the field. This study aimed to determine the characteristics of physicians who are engaged in basic science in efforts to recruit talent. A questionnaire was distributed to all 30 physicians in the basic science departments of Juntendo University School of Medicine. Question items inquired about sex, years since graduation, years between graduation and time entering basic science, clinical experience, recommending the career to medical students, expected obstacles to students entering basic science, efforts to inspire students in research, increased number of lectures and practical training sessions on research, and career choice satisfaction. Correlations between the variables were examined using χ(2) tests. Overall, 26 physicians, including 7 female physicians, returned the questionnaire (response rate 86.7%). Most physicians were satisfied with their career choice. Medical students were deemed not to choose basic science as their future career, because they aimed to become clinicians and because they were concerned about salary. Women physicians in basic science departments were younger than men. Women physicians also considered themselves to make more efforts in inspiring medical students to be interested in research. Moreover, physicians who became basic scientists earlier in their career wanted more research-related lectures in medical education. Improving physicians' salaries in basic science is important to securing talent. In addition, basic science may be a good career path for women physicians to follow.

Negotiable Collateral Damage: Civil Liberties Versus National Security in Times of Threat

DTIC Science & Technology

2011-06-01

physiological, safety, love, esteem , and self -actualization.7 For the individual, defense protects the ability to satisfy these five needs. In his...physical security, ontological security, sociation, self - esteem , and transcendence.8 For the state, the most basic needs are those of its...the hierarchy of needs, falling into the realm of self - esteem and transcendence. The framers of the Constitution appreciated this, sacrificing some

The Effects of Local Economic Conditions on Navy Enlistments.

DTIC Science & Technology

1980-03-18

Standard Metropolitan Statistical Area (SMSA) as the basic economic unit, cross-sectional regression models were constructed for enlistment rate, recruiter...to eligible population suggesting that a cheaper alternative to raising mili- tary wages would be to increase the number of recruiters. Arima (1978...is faced with a number of cri- teria that must be satisfied by an acceptable test variable. As with other variables included in the model , economic

Low Cost Technical Solutions to Jump Start an Insider Threat Program

DTIC Science & Technology

2016-05-11

Low Cost Technical Solutions to Jump Start an Insider Threat Program George J. Silowash Derrick L. Spooner Daniel L. Costa Michael J...Albrethsen May 2016 TECHNICAL NOTE CMU/SEI-2016-TN-004 CERT Division http://www.sei.cmu.edu Copyright 2016 Carnegie Mellon University This... technical note will explore tools that may be suitable for satisfying the basic technical needs of an insider threat program, giving organizations a

Looking into the factors affecting renal patients' quality of life.

PubMed

Theodora, K; Christina, D; Tania, F; Anna, P; Georgios, V

1996-01-01

Quality of life, according to Horquist is "the extent to which one's needs are satisfied, in the context of physical, psychological, social and environmental conditions" (I). Self-esteem is the basic element of a good quality of life. Health-related quality of life consists of a number of components; including family relationships, friendships, finances, physical and psychological status, adjustment to therapy and feeling of security during the treatment.

A Lightweight White-Box Symmetric Encryption Algorithm against Node Capture for WSNs †

PubMed Central

Shi, Yang; Wei, Wujing; He, Zongjian

2015-01-01

Wireless Sensor Networks (WSNs) are often deployed in hostile environments and, thus, nodes can be potentially captured by an adversary. This is a typical white-box attack context, i.e., the adversary may have total visibility of the implementation of the build-in cryptosystem and full control over its execution platform. Handling white-box attacks in a WSN scenario is a challenging task. Existing encryption algorithms for white-box attack contexts require large memory footprint and, hence, are not applicable for wireless sensor networks scenarios. As a countermeasure against the threat in this context, in this paper, we propose a class of lightweight secure implementations of the symmetric encryption algorithm SMS4. The basic idea of our approach is to merge several steps of the round function of SMS4 into table lookups, blended by randomly generated mixing bijections. Therefore, the size of the implementations are significantly reduced while keeping the same security efficiency. The security and efficiency of the proposed solutions are theoretically analyzed. Evaluation shows our solutions satisfy the requirement of sensor nodes in terms of limited memory size and low computational costs. PMID:26007737

Amperometric Enzyme-Based Biosensors for Application in Food and Beverage Industry

NASA Astrophysics Data System (ADS)

Csöoregi, Elisabeth; Gáspñr, Szilveszter; Niculescu, Mihaela; Mattiasson, Bo; Schuhmann, Wolfgang

Continuous, sensitive, selective, and reliable monitoring of a large variety of different compounds in various food and beverage samples is of increasing importance to assure a high-quality and tracing of any possible source of contamination of food and beverages. Most of the presently used classical analytical methods are often requiring expensive instrumentation, long analysis times and well-trained staff. Amperometric enzyme-based biosensors on the other hand have emerged in the last decade from basic science to useful tools with very promising application possibilities in food and beverage industry. Amperometric biosensors are in general highly selective, sensitive, relatively cheap, and easy to integrate into continuous analysis systems. A successful application of such sensors for industrial purposes, however, requires a sensor design, which satisfies the specific needs of monitoring the targeted analyte in the particular application, Since each individual application needs different operational conditions and sensor characteristics, it is obvious that biosensors have to be tailored for the particular case. The characteristics of the biosensors are depending on the used biorecognition element (enzyme), nature of signal transducer (electrode material) and the communication between these two elements (electron-transfer pathway).

Implementation of a Water Flow Control System into the ISS'S Planned Fluids & Combustion Facility

NASA Technical Reports Server (NTRS)

Edwards, Daryl A.

2003-01-01

The Fluids and Combustion Facility (FCF) will become an ISS facility capable of performing basic combustion and fluids research. The facility consists of two independent payload racks specifically configured to support multiple experiments over the life of the ISS. Both racks will depend upon the ISS's Moderate Temperature Loop (MTL) for removing waste heat generated by the avionics and experiments operating within the racks. By using the MTL, constraints are imposed by the ISS vehicle on how the coolant resource is used. On the other hand, the FCF depends upon effective thermal control for maximizing life of the hardware and for supplying proper boundary conditions for the experiments. In the implementation of a design solution, significant factors in the selection of the hardware included ability to measure and control relatively low flow rates, ability to throttle flow within the time constraints of the ISS MTL, conserve energy usage, observe low mass and small volume requirements. An additional factor in the final design solution selection was considering how the system would respond to a loss of power event. This paper describes the method selected to satisfy the FCF design requirements while maintaining the constraints applied by the ISS vehicle.

Preliminary study of a millimeter wave FMCW InSAR for UAS indoor navigation.

PubMed

Scannapieco, Antonio F; Renga, Alfredo; Moccia, Antonio

2015-01-22

Small autonomous unmanned aerial systems (UAS) could be used for indoor inspection in emergency missions, such as damage assessment or the search for survivors in dangerous environments, e.g., power plants, underground railways, mines and industrial warehouses. Two basic functions are required to carry out these tasks, that is autonomous GPS-denied navigation with obstacle detection and high-resolution 3Dmapping with moving target detection. State-of-the-art sensors for UAS are very sensitive to environmental conditions and often fail in the case of poor visibility caused by dust, fog, smoke, flames or other factors that are met as nominal mission scenarios when operating indoors. This paper is a preliminary study concerning an innovative radar sensor based on the interferometric Synthetic Aperture Radar (SAR) principle, which has the potential to satisfy stringent requirements set by indoor autonomous operation. An architectural solution based on a frequency-modulated continuous wave (FMCW) scheme is proposed after a detailed analysis of existing compact and lightweight SAR. A preliminary system design is obtained, and the main imaging peculiarities of the novel sensor are discussed, demonstrating that high-resolution, high-quality observation of an assigned control volume can be achieved.

Preliminary Study of a Millimeter Wave FMCW InSAR for UAS Indoor Navigation

PubMed Central

Scannapieco, Antonio F.; Renga, Alfredo; Moccia, Antonio

2015-01-01

Small autonomous unmanned aerial systems (UAS) could be used for indoor inspection in emergency missions, such as damage assessment or the search for survivors in dangerous environments, e.g., power plants, underground railways, mines and industrial warehouses. Two basic functions are required to carry out these tasks, that is autonomous GPS-denied navigation with obstacle detection and high-resolution 3D mapping with moving target detection. State-of-the-art sensors for UAS are very sensitive to environmental conditions and often fail in the case of poor visibility caused by dust, fog, smoke, flames or other factors that are met as nominal mission scenarios when operating indoors. This paper is a preliminary study concerning an innovative radar sensor based on the interferometric Synthetic Aperture Radar (SAR) principle, which has the potential to satisfy stringent requirements set by indoor autonomous operation. An architectural solution based on a frequency-modulated continuous wave (FMCW) scheme is proposed after a detailed analysis of existing compact and lightweight SAR. A preliminary system design is obtained, and the main imaging peculiarities of the novel sensor are discussed, demonstrating that high-resolution, high-quality observation of an assigned control volume can be achieved. PMID:25621606

Implicit motives and basic need satisfaction in extreme endurance sports.

PubMed

Schüler, Julia; Wegner, Mirko; Knechtle, Beat

2014-06-01

Previous research has shown that the effects of basic psychological needs on the flow experience in sports are moderated by implicit motives. However, so far, only leisure and health-oriented sports have been analyzed. In a pilot study and a main study (N = 29, 93), we tested whether the implicit achievement and affiliation motives interact with the need for competence and the need for social relatedness satisfaction, respectively, to predict flow experience and well-being in extreme endurance athletes. Results showed that highly achievement-motivated individuals benefited more from the need for competence satisfaction in terms of flow than individuals with a low achievement motive did. In addition, highly affiliation-motivated individuals whose need for social relatedness is satisfied reported higher positive affect and lower exercise addiction scores than athletes with a low motive. We discuss the differential effects of the interplay between the achievement and affiliation motives and basic needs on different outcome variables.

Recurrence relations for orthogonal polynomials for PDEs in polar and cylindrical geometries.

PubMed

Richardson, Megan; Lambers, James V

2016-01-01

This paper introduces two families of orthogonal polynomials on the interval (-1,1), with weight function [Formula: see text]. The first family satisfies the boundary condition [Formula: see text], and the second one satisfies the boundary conditions [Formula: see text]. These boundary conditions arise naturally from PDEs defined on a disk with Dirichlet boundary conditions and the requirement of regularity in Cartesian coordinates. The families of orthogonal polynomials are obtained by orthogonalizing short linear combinations of Legendre polynomials that satisfy the same boundary conditions. Then, the three-term recurrence relations are derived. Finally, it is shown that from these recurrence relations, one can efficiently compute the corresponding recurrences for generalized Jacobi polynomials that satisfy the same boundary conditions.

The Geostationary Operational Satellite R Series SpaceWire Based Data System Architecture

NASA Technical Reports Server (NTRS)

Krimchansky, Alexander; Anderson, William H.; Bearer, Craig

2010-01-01

The GOES-R program selected SpaceWire as the best solution to satisfy the desire for simple and flexible instrument to spacecraft command and telemetry communications. Data generated by GOES-R instruments is critical for meteorological forecasting, public safety, space weather, and other key applications. In addition, GOES-R instrument data is provided to ground stations on a 24/7 basis. GOES-R requires data errors be detected and corrected from origin to final destination. This paper describes GOES-R developed strategy to satisfy this requirement

Requirements based system level risk modeling

NASA Technical Reports Server (NTRS)

Meshkat, Leila; Cornford, Steven; Feather, Martin

2004-01-01

The problem that we address in this paper is assessing the expected degree of success of the system or mission based on the degree to which each requirement is satisfied and the relative weight of the requirements.

Regulation of cellular iron metabolism

PubMed Central

Wang, Jian; Pantopoulos, Kostas

2011-01-01

Iron is an essential but potentially hazardous biometal. Mammalian cells require sufficient amounts of iron to satisfy metabolic needs or to accomplish specialized functions. Iron is delivered to tissues by circulating transferrin, a transporter that captures iron released into the plasma mainly from intestinal enterocytes or reticuloendothelial macrophages. The binding of iron-laden transferrin to the cell-surface transferrin receptor 1 results in endocytosis and uptake of the metal cargo. Internalized iron is transported to mitochondria for the synthesis of haem or iron–sulfur clusters, which are integral parts of several metalloproteins, and excess iron is stored and detoxified in cytosolic ferritin. Iron metabolism is controlled at different levels and by diverse mechanisms. The present review summarizes basic concepts of iron transport, use and storage and focuses on the IRE (iron-responsive element)/IRP (iron-regulatory protein) system, a well known post-transcriptional regulatory circuit that not only maintains iron homoeostasis in various cell types, but also contributes to systemic iron balance. PMID:21348856

Preparation and characterisation of CNF/MWCNT carbon aerogel as efficient adsorbents.

PubMed

Xu, Zhaoyang; Jiang, Xiangdong; Tan, Sicong; Wu, Weibing; Shi, Jiangtao; Zhou, Huan; Chen, Peng

2018-06-01

In recent years, carbon aerogels have attracted much attention in basic research and as potential applications in many fields. Herein, the authors report a novel approach using bamboo powder as raw material to fabricate cellulose nanofibers (CNFs)/multi-walled carbon nanotubes (MWCNTs) carbon aerogels by a simple dipping and carbonisation process. The developed material exhibits many exciting properties including low density (0.056 g cm -3 ), high porosity (95%), efficient capability for separation of oily droplets from water, and high adsorption capacity for a variety of oils and organic solvents by up to 110 times its own weight. Furthermore, the CNF/MWCNT carbon aerogels (CMCA) can be recycled many times by distillation and combustion, satisfying the requirements of practical oil-water separation. Taken together with its economical, environmentally benign manufacturing process, sustainability of the precursor and versatility of material, the CMCA developed in this study will be a promising candidate for addressing the problems arising from the spills of oily compounds.

Reinventing clinical trials: a review of innovative biomarker trial designs in cancer therapies.

PubMed

Lin, Ja-An; He, Pei

2015-06-01

Recently, new clinical trial designs involving biomarkers have been studied and proposed in cancer clinical research, in the hope of incorporating the rapid growing basic research into clinical practices. Journal articles related to various biomarkers and their role in cancer clinical trial, articles and books about statistical issues in trial design, and regulatory website, documents, and guidance for submission of targeted cancer therapies. The drug development process involves four phases. The confirmatory Phase III is essential in regulatory approval of a special treatment. Regulatory agency has restrictions on confirmatory trials 'using adaptive designs'. No rule of thumb to pick the most appropriate design for biomarker-related trials. Statistical issues to solve in new designs. Regulatory acceptance of the 'newly proposed trial designs'. Biomarker-related trial designs that can resolve the statistical issues and satisfy the regulatory requirement. © The Author 2015. Published by Oxford University Press. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Towards Optical Partial Discharge Detection with Micro Silicon Photomultipliers

PubMed Central

Ren, Ming; Song, Bo; Dong, Ming

2017-01-01

Optical detection is reliable in intrinsically characterizing partial discharges (PDs). Because of the great volume and high-level power supply of the optical devices that can satisfy the requirements in photosensitivity, optical PD detection can merely be used in laboratory studies. To promote the practical application of the optical approach in an actual power apparatus, a silicon photomultiplier (SiPM)-based PD sensor is introduced in this paper, and its basic properties, which include the sensitivity, pulse resolution, correlation with PD severity, and electromagnetic (EM) interference immunity, are experimentally evaluated. The stochastic phase-resolved PD pattern (PRPD) for three typical insulation defects are obtained by SiPM PD detector and are compared with those obtained using a high-frequency current transformer (HFCT) and a vacuum photomultiplier tube (PMT). Because of its good performances in the above aspects and its additional advantages, such as the small size, low power supply, and low cost, SiPM offers great potential in practical optical PD monitoring. PMID:29125544

Towards Optical Partial Discharge Detection with Micro Silicon Photomultipliers.

PubMed

Ren, Ming; Zhou, Jierui; Song, Bo; Zhang, Chongxing; Dong, Ming; Albarracín, Ricardo

2017-11-10

Optical detection is reliable in intrinsically characterizing partial discharges (PDs). Because of the great volume and high-level power supply of the optical devices that can satisfy the requirements in photosensitivity, optical PD detection can merely be used in laboratory studies. To promote the practical application of the optical approach in an actual power apparatus, a silicon photomultiplier (SiPM)-based PD sensor is introduced in this paper, and its basic properties, which include the sensitivity, pulse resolution, correlation with PD severity, and electromagnetic (EM) interference immunity, are experimentally evaluated. The stochastic phase-resolved PD pattern (PRPD) for three typical insulation defects are obtained by SiPM PD detector and are compared with those obtained using a high-frequency current transformer (HFCT) and a vacuum photomultiplier tube (PMT). Because of its good performances in the above aspects and its additional advantages, such as the small size, low power supply, and low cost, SiPM offers great potential in practical optical PD monitoring.

Systematics for checking geometric errors in CNC lathes

NASA Astrophysics Data System (ADS)

Araújo, R. P.; Rolim, T. L.

2015-10-01

Non-idealities presented in machine tools compromise directly both the geometry and the dimensions of machined parts, generating distortions in the project. Given the competitive scenario among different companies, it is necessary to have knowledge of the geometric behavior of these machines in order to be able to establish their processing capability, avoiding waste of time and materials as well as satisfying customer requirements. But despite the fact that geometric tests are important and necessary to clarify the use of the machine correctly, therefore preventing future damage, most users do not apply such tests on their machines for lack of knowledge or lack of proper motivation, basically due to two factors: long period of time and high costs of testing. This work proposes a systematics for checking straightness and perpendicularity errors in CNC lathes demanding little time and cost with high metrological reliability, to be used on factory floors of small and medium-size businesses to ensure the quality of its products and make them competitive.

Research on common methods for evaluating the operation effect of integrated wastewater treatment facilities of iron and steel enterprises

NASA Astrophysics Data System (ADS)

Bingsheng, Xu

2017-04-01

Considering the large quantities of wastewater generated from iron and steel enterprises in China, this paper is aimed to research the common methods applied for evaluating the integrated wastewater treatment effect of iron and steel enterprises. Based on survey results on environmental protection performance, technological economy, resource & energy consumption, services and management, an indicator system for evaluating the operation effect of integrated wastewater treatment facilities is set up. By discussing the standards and industrial policies in and out of China, 27 key secondary indicators are further defined on the basis of investigation on main equipment and key processes for wastewater treatment, so as to determine the method for setting key quantitative and qualitative indicators for evaluation indicator system. It is also expected to satisfy the basic requirements of reasonable resource allocation, environmental protection and sustainable economic development, further improve the integrated wastewater treatment effect of iron and steel enterprises, and reduce the emission of hazardous substances and environmental impact.

Development of a nickel/metal hydride battery (Ni/MH) system for EV application

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ikoma, M.; Hamada, S.; Morishita, N.

1994-12-31

In order to satisfy basic battery characteristics for electric vehicles (EV) such as specific energy, specific power and cycle life that are required for driving on urban streets, the authors have selected the valve-regulated lead acid battery as a conventional battery and the nickel/metal-hydride battery as an advanced battery, and have been studying their development in order to put them into practical use by 1998. Regarding the nickel/metal-hydride battery, excellent nickel positive electrode with high temperature charge efficiency accomplished with additives such as Ca compounds, and an exceedingly good hydrogen absorbing alloy negative electrode with high capacity and long cyclemore » life, achieved by adjustment of alloy composition, surface treatment, and control of binder and conductive additive have been developed to overcome difficulties in the scale-up of battery size. Modular batteries using this technology possess specific energy twice (70 Wh/kg) that of the lead-acid battery, and have superior specific power (160 Wh/kg) and cycle life. 5 refs.« less

Analysis and documentation of QCSEE (Quiet Clean Short-haul Experimental Engine) over-the-wing exhaust system development

NASA Technical Reports Server (NTRS)

Ammer, R. C.; Kutney, J. T.

1977-01-01

A static scale model test program was conducted in the static test area of the NASA-Langley 9.14- by 18.29 m(30- by 60-ft) Full-Scale Wind Tunnel Facility to develop an over-the-wing (OTW) nozzle and reverser configuration for the Quiet Clean Short-Haul Experimental Engine (QCSEE). Three nozzles and one basic reverser configuration were tested over the QCSEE takeoff and approach power nozzle pressure ratio range between 1.1 and 1.3. The models were scaled to 8.53% of QCSEE engine size and tested behind two 13.97-cm (5.5-in.) diameter tip-turbine-driven fan simulators coupled in tandem. An OTW nozzle and reverser configuration was identified which satisfies the QCSEE experimental engine requirements in terms of nozzle cycle area variation capability and reverse thrust level, and provides good jet flow spreading over a wing upper surface for achievement of high propulsive lift performance.

26 CFR 1.401(a)(4)-6 - Contributory defined benefit plans.

Code of Federal Regulations, 2010 CFR

2010-04-01

... (b)(2)(ii)(A) merely because it eliminates employee contributions for all employees with plan year...) In general. A contributory DB plan satisfies this paragraph (b)(2)(ii)(B) if it satisfies either of... employee's base benefit percentage as required under paragraph (b)(2)(iii)(B)(1) of this section, it may be...

77 FR 70376 - Withdrawal of Approval of Air Quality Implementation Plans and Findings of Failure To Submit...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-11-26

... satisfies the requirement regarding offsetting emissions growth caused by growth in vehicle miles traveled...-month time clock for mandatory imposition of sanctions and the two-year time clock for EPA to promulgate... technologies for boilers in CAA 182(e)(3); and (7) provisions satisfying the vehicle miles traveled (VMT...

26 CFR 48.6715-1 - Penalty for misuse of dyed fuel.

Code of Federal Regulations, 2012 CFR

2012-04-01

...) will not apply in the following cases: (1) Diesel fuel or kerosene that satisfies the dyeing and... kerosene that satisfies the dyeing and marking requirements of § 48.4082-1 (b) and (c) is blended with any other liquid (other than diesel fuel or kerosene) that contains the type and amount of dye and marker...

26 CFR 48.6715-1 - Penalty for misuse of dyed fuel.

Code of Federal Regulations, 2010 CFR

2010-04-01

...) will not apply in the following cases: (1) Diesel fuel or kerosene that satisfies the dyeing and... kerosene that satisfies the dyeing and marking requirements of § 48.4082-1 (b) and (c) is blended with any other liquid (other than diesel fuel or kerosene ) that contains the type and amount of dye and marker...

26 CFR 48.6715-1 - Penalty for misuse of dyed fuel.

Code of Federal Regulations, 2011 CFR

2011-04-01

...) will not apply in the following cases: (1) Diesel fuel or kerosene that satisfies the dyeing and... kerosene that satisfies the dyeing and marking requirements of § 48.4082-1 (b) and (c) is blended with any other liquid (other than diesel fuel or kerosene ) that contains the type and amount of dye and marker...

26 CFR 48.6715-1 - Penalty for misuse of dyed fuel.

Code of Federal Regulations, 2013 CFR

2013-04-01

...) will not apply in the following cases: (1) Diesel fuel or kerosene that satisfies the dyeing and... kerosene that satisfies the dyeing and marking requirements of § 48.4082-1 (b) and (c) is blended with any other liquid (other than diesel fuel or kerosene) that contains the type and amount of dye and marker...

Modeling of shock wave propagation in large amplitude ultrasound.

PubMed

Pinton, Gianmarco F; Trahey, Gregg E

2008-01-01

The Rankine-Hugoniot relation for shock wave propagation describes the shock speed of a nonlinear wave. This paper investigates time-domain numerical methods that solve the nonlinear parabolic wave equation, or the Khokhlov-Zabolotskaya-Kuznetsov (KZK) equation, and the conditions they require to satisfy the Rankine-Hugoniot relation. Two numerical methods commonly used in hyperbolic conservation laws are adapted to solve the KZK equation: Godunov's method and the monotonic upwind scheme for conservation laws (MUSCL). It is shown that they satisfy the Rankine-Hugoniot relation regardless of attenuation. These two methods are compared with the current implicit solution based method. When the attenuation is small, such as in water, the current method requires a degree of grid refinement that is computationally impractical. All three numerical methods are compared in simulations for lithotripters and high intensity focused ultrasound (HIFU) where the attenuation is small compared to the nonlinearity because much of the propagation occurs in water. The simulations are performed on grid sizes that are consistent with present-day computational resources but are not sufficiently refined for the current method to satisfy the Rankine-Hugoniot condition. It is shown that satisfying the Rankine-Hugoniot conditions has a significant impact on metrics relevant to lithotripsy (such as peak pressures) and HIFU (intensity). Because the Godunov and MUSCL schemes satisfy the Rankine-Hugoniot conditions on coarse grids, they are particularly advantageous for three-dimensional simulations.

Sense and avoid technology for Global Hawk and Predator UAVs

NASA Astrophysics Data System (ADS)

McCalmont, John F.; Utt, James; Deschenes, Michael; Taylor, Michael J.

2005-05-01

The Sensors Directorate at the Air Force Research Laboratory (AFRL) along with Defense Research Associates, Inc. (DRA) conducted a flight demonstration of technology that could potentially satisfy the Federal Aviation Administration's (FAA) requirement for Unmanned Aerial Vehicles (UAVs) to sense and avoid local air traffic sufficient to provide an "...equivalent level of safety, comparable to see-and-avoid requirements for manned aircraft". This FAA requirement must be satisfied for autonomous UAV operation within the national airspace. The real-time on-board system passively detects approaching aircraft, both cooperative and non-cooperative, using imaging sensors operating in the visible/near infrared band and a passive moving target indicator algorithm. Detection range requirements for RQ-4 and MQ-9 UAVs were determined based on analysis of flight geometries, avoidance maneuver timelines, system latencies and human pilot performance. Flight data and UAV operating parameters were provided by the system program offices, prime contractors, and flight-test personnel. Flight demonstrations were conducted using a surrogate UAV (Aero Commander) and an intruder aircraft (Beech Bonanza). The system demonstrated target detection ranges out to 3 nautical miles in nose-to-nose scenarios and marginal visual meteorological conditions. (VMC) This paper will describe the sense and avoid requirements definition process and the system concept (sensors, algorithms, processor, and flight rest results) that has demonstrated the potential to satisfy the FAA sense and avoid requirements.

Space station Simulation Computer System (SCS) study for NASA/MSFC. Volume 2: Concept document

NASA Technical Reports Server (NTRS)

1989-01-01

The Simulation Computer System (SCS) concept document describes and establishes requirements for the functional performance of the SCS system, including interface, logistic, and qualification requirements. The SCS is the computational communications and display segment of the Marshall Space Flight Center (MSFC) Payload Training Complex (PTC). The PTC is the MSFC facility that will train onboard and ground operations personnel to operate the payloads and experiments on board the international Space Station Freedom. The requirements to be satisfied by the system implementation are identified here. The SCS concept document defines the requirements to be satisfied through the implementation of the system capability. The information provides the operational basis for defining the requirements to be allocated to the system components and enables the system organization to assess whether or not the completed system complies with the requirements of the system.

20 CFR 655.152 - Advertising requirements.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 20 Employees' Benefits 3 2012-04-01 2012-04-01 false Advertising requirements. 655.152 Section 655... Employment in the United States (H-2A Workers) Post-Acceptance Requirements § 655.152 Advertising requirements. All advertising conducted to satisfy the required recruitment activities under § 655.151 must...

20 CFR 655.152 - Advertising requirements.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 20 Employees' Benefits 3 2010-04-01 2010-04-01 false Advertising requirements. 655.152 Section 655... Employment in the United States (H-2A Workers) Post-Acceptance Requirements § 655.152 Advertising requirements. All advertising conducted to satisfy the required recruitment activities under § 655.151 must...

20 CFR 655.152 - Advertising requirements.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 20 Employees' Benefits 3 2013-04-01 2013-04-01 false Advertising requirements. 655.152 Section 655... Employment in the United States (H-2A Workers) Post-Acceptance Requirements § 655.152 Advertising requirements. All advertising conducted to satisfy the required recruitment activities under § 655.151 must...

20 CFR 655.152 - Advertising requirements.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 20 Employees' Benefits 3 2014-04-01 2014-04-01 false Advertising requirements. 655.152 Section 655... Employment in the United States (H-2A Workers) Post-Acceptance Requirements § 655.152 Advertising requirements. All advertising conducted to satisfy the required recruitment activities under § 655.151 must...

20 CFR 655.152 - Advertising requirements.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 20 Employees' Benefits 3 2011-04-01 2011-04-01 false Advertising requirements. 655.152 Section 655... Employment in the United States (H-2A Workers) Post-Acceptance Requirements § 655.152 Advertising requirements. All advertising conducted to satisfy the required recruitment activities under § 655.151 must...

Microwave ECR Ion Thruster Development Activities at NASA Glenn Research Center

NASA Technical Reports Server (NTRS)

Foster, John E.; Patterson, Michael J.

2002-01-01

Outer solar system missions will have propulsion system lifetime requirements well in excess of that which can be satisfied by ion thrusters utilizing conventional hollow cathode technology. To satisfy such mission requirements, other technologies must be investigated. One possible approach is to utilize electrodeless plasma production schemes. Such an approach has seen low power application less than 1 kW on earth-space spacecraft such as ARTEMIS which uses the rf thruster the RIT 10 and deep space missions such as MUSES-C which will use a microwave ion thruster. Microwave and rf thruster technologies are compared. A microwave-based ion thruster is investigated for potential high power ion thruster systems requiring very long lifetimes.

The Changing Role of Money as a Motivator.

DTIC Science & Technology

1982-04-23

61). Abraham Maslow advanced the theory that man is motivated by a hierachy of needs . Maslow classified human needs into a pyramidal structure as...theory, man strives to fill these needs in their order of hierachy , with the basic phsiological needs being satis- fied first. The physiological and safety... needs are most closely asso- ciated with the desire for money. vowever, as a person moves up through the hierachy , the ability of money to satisfy

Trends in NASA communication satellites

NASA Technical Reports Server (NTRS)

Sivo, J. N.; Robbins, W. H.; Stretchberry, D. M.

1972-01-01

Satellite telecommunications can help to satisfy several national needs such as education, health care, cultural opportunities, and data transfer. There are current experiments being conducted with NASA spacecraft ATS 1, 3, and 5 in an attempt to satisfy these national needs. Future experiments are planned for the ATS F/G and CTS spacecrafts. The next generation of communications satellites must provide multiple region coverage, multichannel capability, high quality TV pictures, and must allow low cost ground receivers to be used. The proposed NASA spacecrafts, ATS H/I, will satisfy these requirements. Other countries of the world can benefit from ATS H/I technology.

40 CFR 161.70 - Acceptable protocols.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Development (OECD) Protocols. Tests conducted in accordance with the requirements and recommendations of the... data generated by the study will satisfy the requirements of this part. (c) Procedures for requesting...

Experimental investigation of two-phase heat transfer in a porous matrix.

NASA Technical Reports Server (NTRS)

Von Reth, R.; Frost, W.

1972-01-01

One-dimensional two-phase flow transpiration cooling through porous metal is studied experimentally. The experimental data is compared with a previous one-dimensional analysis. Good agreement with calculated temperature distribution is obtained as long as the basic assumptions of the analytical model are satisfied. Deviations from the basic assumptions are caused by nonhomogeneous and oscillating flow conditions. Preliminary derivation of nondimensional parameters which characterize the stable and unstable flow conditions is given. Superheated liquid droplets observed sputtering from the heated surface indicated incomplete evaporation at heat fluxes well in access of the latent energy transport. A parameter is developed to account for the nonequilibrium thermodynamic effects. Measured and calculated pressure drops show contradicting trends which are attributed to capillary forces.

The rested relationship: Sleep benefits marital evaluations.

PubMed

Maranges, Heather M; McNulty, James K

2017-02-01

Remaining satisfied with a relationship often requires thinking in ways that use self-regulatory resources-satisfied couples discount undesirable experiences when forming global evaluations of the relationship. Nevertheless, recent work indicates that the self-regulatory resources required to engage in these processes are limited. Although consuming new energy may be one way to replenish these limited resources, sleep is another. The current study used a daily diary study of 68 newlywed couples to examine the implications of sleep for daily marital evaluations. Every day for up to 7 days, both members of the couples reported their evaluations of their interpersonal specific experiences, global relationship satisfaction, and amount of sleep. Multilevel analysis revealed that spouses were more satisfied on days after which they had slept for a longer period of time. Furthermore, sleep also buffered husbands', but not wives', marital satisfaction against the implications of negative specific evaluations-husbands were better able to remain more globally satisfied despite negative evaluations of specific aspects of the relationship on days following more sleep. These findings suggest that sleep may offer self-regulatory benefits and should thus be incorporated into existing interpersonal models that highlight the importance of self-regulation. (PsycINFO Database Record (c) 2017 APA, all rights reserved).

Results of an academic promotion and career path survey of faculty at the Johns Hopkins University School of Medicine.

PubMed

Thomas, Patricia A; Diener-West, Marie; Canto, Marcia I; Martin, Don R; Post, Wendy S; Streiff, Michael B

2004-03-01

Clinician-educator faculty are increasing in numbers in academic medical centers, but their academic advancement is slower than that of research faculty. The authors sought to quantify the magnitude of this difference in career advancement and to explore the characteristics of faculty that might explain the difference. In 1999, a questionnaire was administered to all MD faculty at the rank of instructor and above (259) in the Department of Medicine at the Johns Hopkins University School of Medicine. A total of 180 (69%) faculty returned questionnaires. Of these, 178 identified with one of four career paths: basic researcher (46), clinical researcher (69), academic clinician (38), or teacher-clinician (25). Career path did not differ by age, gender, rank, years on faculty, hours worked per week, family responsibility, or global work satisfaction. After adjusting for age, gender, time at rank, and work satisfaction, the odds of being at a higher rank were 85% less for academic clinicians (odds ratio,.15; 95% confidence interval, 0.06-0.40) and 69% less for teacher-clinicians (odds ratio,.31; 95% confidence interval, 0.11-0.88) than for basic researchers. Clinical researchers did not differ from basic researchers in the likelihood of being at higher rank. Similarly, compared with basic research faculty, the adjusted odds of being more satisfied with progress towards academic promotion were 92% lower for academic clinicians and 87% lower for teacher-clinicians. Clinician-educator faculty were less likely to be at higher rank at this institution than were faculty in research paths. Differences in rank may be explained by lower rank at hire for faculty in these career paths, time available for scholarly activities, or other resources available to support scholarship. Retaining clinician-educators will require further exploration of barriers to promotion inherent to these career paths and methods of modifying these barriers.

13 CFR 130.480 - Program income.

Code of Federal Regulations, 2014 CFR

2014-01-01

... based in universities or nonprofit organizations shall be subject to OMB requirements (see OMB Circular... network. It cannot be used to satisfy the requirements for Matching Funds. The Project Officer shall...

13 CFR 130.480 - Program income.

Code of Federal Regulations, 2013 CFR

2013-01-01

... based in universities or nonprofit organizations shall be subject to OMB requirements (see OMB Circular... network. It cannot be used to satisfy the requirements for Matching Funds. The Project Officer shall...

13 CFR 130.480 - Program income.

Code of Federal Regulations, 2012 CFR

2012-01-01

... based in universities or nonprofit organizations shall be subject to OMB requirements (see OMB Circular... network. It cannot be used to satisfy the requirements for Matching Funds. The Project Officer shall...

13 CFR 130.480 - Program income.

Code of Federal Regulations, 2010 CFR

2010-01-01

... based in universities or nonprofit organizations shall be subject to OMB requirements (see OMB Circular... network. It cannot be used to satisfy the requirements for Matching Funds. The Project Officer shall...

State transformations and Hamiltonian structures for optimal control in discrete systems

NASA Astrophysics Data System (ADS)

Sieniutycz, S.

2006-04-01

Preserving usual definition of Hamiltonian H as the scalar product of rates and generalized momenta we investigate two basic classes of discrete optimal control processes governed by the difference rather than differential equations for the state transformation. The first class, linear in the time interval θ, secures the constancy of optimal H and satisfies a discrete Hamilton-Jacobi equation. The second class, nonlinear in θ, does not assure the constancy of optimal H and satisfies only a relationship that may be regarded as an equation of Hamilton-Jacobi type. The basic question asked is if and when Hamilton's canonical structures emerge in optimal discrete systems. For a constrained discrete control, general optimization algorithms are derived that constitute powerful theoretical and computational tools when evaluating extremum properties of constrained physical systems. The mathematical basis is Bellman's method of dynamic programming (DP) and its extension in the form of the so-called Carathéodory-Boltyanski (CB) stage optimality criterion which allows a variation of the terminal state that is otherwise fixed in Bellman's method. For systems with unconstrained intervals of the holdup time θ two powerful optimization algorithms are obtained: an unconventional discrete algorithm with a constant H and its counterpart for models nonlinear in θ. We also present the time-interval-constrained extension of the second algorithm. The results are general; namely, one arrives at: discrete canonical equations of Hamilton, maximum principles, and (at the continuous limit of processes with free intervals of time) the classical Hamilton-Jacobi theory, along with basic results of variational calculus. A vast spectrum of applications and an example are briefly discussed with particular attention paid to models nonlinear in the time interval θ.

Recursive Deadbeat Controller Design

NASA Technical Reports Server (NTRS)

Juang, Jer-Nan; Phan, Minh Q.

1997-01-01

This paper presents a recursive algorithm for a deadbeat predictive controller design. The method combines together the concepts of system identification and deadbeat controller designs. It starts with the multi-step output prediction equation and derives the control force in terms of past input and output time histories. The formulation thus derived satisfies simultaneously system identification and deadbeat controller design requirements. As soon as the coefficient matrices are identified satisfying the output prediction equation, no further work is required to compute the deadbeat control gain matrices. The method can be implemented recursively just as any typical recursive system identification techniques.

10 CFR 851.13 - Compliance.

Code of Federal Regulations, 2012 CFR

2012-01-01

... with the requirements of this rule before February 9, 2007. (b) In the event a contractor has... methods to be added to the existing program, description, or process, that satisfy the requirements of...

76 FR 37195 - Proposed Collection; Comment Request for Regulation Project

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-24

... preparer penalties-manual signature requirement. DATES: Written comments should be received on or before... . SUPPLEMENTARY INFORMATION: Title: Preparer Penalties-Manual Signature Requirement (Sec. 1.6695-1(B)). OMB Number..., satisfy the manual signature requirements by using a facsimile signature. However, they will be required...

76 FR 23713 - Wireless E911 Location Accuracy Requirements

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-28

... Location Accuracy Requirements AGENCY: Federal Communications Commission. ACTION: Final rule; announcement... contained in regulations concerning wireless E911 location accuracy requirements. The information collection... standards for wireless Enhanced 911 (E911) Phase II location accuracy and reliability to satisfy these...

Hunger promotes acquisition of nonfood objects.

PubMed

Xu, Alison Jing; Schwarz, Norbert; Wyer, Robert S

2015-03-03

Hunger motivates people to consume food, for which finding and acquiring food is a prerequisite. We test whether the acquisition component spills over to nonfood objects: Are hungry people more likely to acquire objects that cannot satisfy their hunger? Five laboratory and field studies show that hunger increases the accessibility of acquisition-related concepts and the intention to acquire not only food but also nonfood objects. Moreover, people act on this intention and acquire more nonfood objects (e.g., binder clips) when they are hungry, both when these items are freely available and when they must be paid for. However, hunger does not influence how much they like nonfood objects. We conclude that a basic biologically based motivation can affect substantively unrelated behaviors that cannot satisfy the motivation. This presumably occurs because hunger renders acquisition-related concepts and behaviors more accessible, which influences decisions in situations to which they can be applied.

A Comparison of Experimental and Theoretical Results for Labyrinth Gas Seals. Ph.D. Thesis

NASA Technical Reports Server (NTRS)

Scharrer, Joseph Kirk

1987-01-01

The basic equations are derived for a two control volume model for compressible flow in a labyrinth seal. The flow is assumed to be completely turbulent and isoenergetic. The wall friction factors are determined using the Blasius formula. Jet flow theory is used for the calculation of the recirculation velocity in the cavity. Linearized zeroth and first order perturbation equations are developed for small motion about a centered position by an expansion in the eccentricity ratio. The zeroth order pressure distribution is found by satisfying the leakage equation. The circumferential velocity distribution is determined by satisfying the momentum equations. The first order equations are solved by a separation of variable solution. Integration of the resultant pressure distribution along and around the seal defines the reaction force developed by the seal and the corresponding dynamic coefficients. The results of this analysis are compared to experimental test results.

Hunger promotes acquisition of nonfood objects

PubMed Central

Xu, Alison Jing; Schwarz, Norbert; Wyer, Robert S.

2015-01-01

Hunger motivates people to consume food, for which finding and acquiring food is a prerequisite. We test whether the acquisition component spills over to nonfood objects: Are hungry people more likely to acquire objects that cannot satisfy their hunger? Five laboratory and field studies show that hunger increases the accessibility of acquisition-related concepts and the intention to acquire not only food but also nonfood objects. Moreover, people act on this intention and acquire more nonfood objects (e.g., binder clips) when they are hungry, both when these items are freely available and when they must be paid for. However, hunger does not influence how much they like nonfood objects. We conclude that a basic biologically based motivation can affect substantively unrelated behaviors that cannot satisfy the motivation. This presumably occurs because hunger renders acquisition-related concepts and behaviors more accessible, which influences decisions in situations to which they can be applied. PMID:25730858

Line managers as marketers.

PubMed

Rynne, T J

1986-09-01

Many hospital administrators and boards of directors, having overcome their initial opposition to advertising and hired a marketing professional, are wondering why their marketing programs have not accomplished all that they had hoped. The answer lies in their perception of who is responsible for marketing. Marketing is not a specialty separate from the disciplines of management--it is a basic management skill. Its goal is to satisfy the customer by providing products and services that meet the customer's needs, wants, and preferences. Line managers must understand the hospital's customers and make the critical day-to-day differences in satisfying them. They are the hospital's front-line marketers, and the marketing department's role is to support them in this function. The marketing department should develop the line managers' marketing skills by furnishing them with the appropriate tools: formats, models, examples, and instructions. In addition, the marketing staff should provide such specialized services as marketing research, ad agency management, and development of communications.

Stripline/Microstrip Transition in Multilayer Circuit Board

NASA Technical Reports Server (NTRS)

Epp, Larry; Khan, Abdur

2005-01-01

A stripline-to-microstrip transition has been incorporated into a multilayer circuit board that supports a distributed solid-state microwave power amplifier, for the purpose of coupling the microwave signal from a buried-layer stripline to a top-layer microstrip. The design of the transition could be adapted to multilayer circuit boards in such products as cellular telephones (for connecting between circuit-board signal lines and antennas), transmitters for Earth/satellite communication systems, and computer mother boards (if processor speeds increase into the range of tens of gigahertz). The transition is designed to satisfy the following requirements in addition to the basic coupling requirement described above: (1) The transition must traverse multiple layers, including intermediate layers that contain DC circuitry. (2) The transition must work at a frequency of 32 GHz with low loss and low reflection. (3) The power delivered by the transition to top-layer microstrip must be split equally in opposite directions along the microstrip. Referring to the figure, this amounts to a requirement that when power is supplied to input port 1, equal amounts of power flow through output ports 2 and 3. (4) The signal-line via that is necessarily a part of such a transition must not be what is known in the art as a blind via; that is, it must span the entire thickness of the circuit board.

Evaluating Security Controls Based on Key Performance Indicators and Stakeholder Mission

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sheldon, Frederick T; Abercrombie, Robert K; Mili, Ali

2008-01-01

Good security metrics are required to make good decisions about how to design security countermeasures, to choose between alternative security architectures, and to improve security during operations. Therefore, in essence, measurement can be viewed as a decision aid. The lack of sound practical security metrics is severely hampering progress in the development of secure systems. The Cyberspace Security Econometrics System (CSES) offers the following advantages over traditional measurement systems: (1) CSES reflects the variances that exist amongst different stakeholders of the same system. Different stakeholders will typically attach different stakes to the same requirement or service (e.g., a service maymore » be provided by an information technology system or process control system, etc.). (2) For a given stakeholder, CSES reflects the variance that may exist among the stakes she/he attaches to meeting each requirement. The same stakeholder may attach different stakes to satisfying different requirements within the overall system specification. (3) For a given compound specification (e.g., combination(s) of commercial off the shelf software and/or hardware), CSES reflects the variance that may exist amongst the levels of verification and validation (i.e., certification) performed on components of the specification. The certification activity may produce higher levels of assurance across different components of the specification than others. Consequently, this paper introduces the basis, objectives and capabilities for the CSES including inputs/outputs and the basic structural and mathematical underpinnings.« less

The space of ultrametric phylogenetic trees.

PubMed

Gavryushkin, Alex; Drummond, Alexei J

2016-08-21

The reliability of a phylogenetic inference method from genomic sequence data is ensured by its statistical consistency. Bayesian inference methods produce a sample of phylogenetic trees from the posterior distribution given sequence data. Hence the question of statistical consistency of such methods is equivalent to the consistency of the summary of the sample. More generally, statistical consistency is ensured by the tree space used to analyse the sample. In this paper, we consider two standard parameterisations of phylogenetic time-trees used in evolutionary models: inter-coalescent interval lengths and absolute times of divergence events. For each of these parameterisations we introduce a natural metric space on ultrametric phylogenetic trees. We compare the introduced spaces with existing models of tree space and formulate several formal requirements that a metric space on phylogenetic trees must possess in order to be a satisfactory space for statistical analysis, and justify them. We show that only a few known constructions of the space of phylogenetic trees satisfy these requirements. However, our results suggest that these basic requirements are not enough to distinguish between the two metric spaces we introduce and that the choice between metric spaces requires additional properties to be considered. Particularly, that the summary tree minimising the square distance to the trees from the sample might be different for different parameterisations. This suggests that further fundamental insight is needed into the problem of statistical consistency of phylogenetic inference methods. Copyright © 2016 The Authors. Published by Elsevier Ltd.. All rights reserved.

Heterogeneous Superconducting Low-Noise Sensing Coils

NASA Technical Reports Server (NTRS)

Hahn, Inseob; Penanen, Konstantin I.; Ho Eom, Byeong

2008-01-01

A heterogeneous material construction has been devised for sensing coils of superconducting quantum interference device (SQUID) magnetometers that are subject to a combination of requirements peculiar to some advanced applications, notably including low-field magnetic resonance imaging for medical diagnosis. The requirements in question are the following: The sensing coils must be large enough (in some cases having dimensions of as much as tens of centimeters) to afford adequate sensitivity; The sensing coils must be made electrically superconductive to eliminate Johnson noise (thermally induced noise proportional to electrical resistance); and Although the sensing coils must be cooled to below their superconducting- transition temperatures with sufficient cooling power to overcome moderate ambient radiative heat leakage, they must not be immersed in cryogenic liquid baths. For a given superconducting sensing coil, this combination of requirements can be satisfied by providing a sufficiently thermally conductive link between the coil and a cold source. However, the superconducting coil material is not suitable as such a link because electrically superconductive materials are typically poor thermal conductors. The heterogeneous material construction makes it possible to solve both the electrical- and thermal-conductivity problems. The basic idea is to construct the coil as a skeleton made of a highly thermally conductive material (typically, annealed copper), then coat the skeleton with an electrically superconductive alloy (typically, a lead-tin solder) [see figure]. In operation, the copper skeleton provides the required thermally conductive connection to the cold source, while the electrically superconductive coating material shields against Johnson noise that originates in the copper skeleton.

40 CFR 161.440 - Spray drift data requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

...) Notes General use patterns Terrestrial Food crop Nonfood Aquatic Food crop Nonfood Greenhouse Food crop..., fish and wildlife, and nontarget plants. This requirement may be satisfied by submittal of published or...

40 CFR 161.440 - Spray drift data requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

...) Notes General use patterns Terrestrial Food crop Nonfood Aquatic Food crop Nonfood Greenhouse Food crop..., fish and wildlife, and nontarget plants. This requirement may be satisfied by submittal of published or...

Alternate-Fueled Combustor-Sector Performance: Part A: Combustor Performance Part B: Combustor Emissions

NASA Technical Reports Server (NTRS)

Shouse, D. T.; Neuroth, C.; Henricks, R. C.; Lynch, A.; Frayne, C.; Stutrud, J. S.; Corporan, E.; Hankins, T.

2010-01-01

Alternate aviation fuels for military or commercial use are required to satisfy MIL-DTL-83133F(2008) or ASTM D 7566 (2010) standards, respectively, and are classified as drop-in fuel replacements. To satisfy legacy issues, blends to 50% alternate fuel with petroleum fuels are certified individually on the basis of feedstock. Adherence to alternate fuels and fuel blends requires smart fueling systems or advanced fuel-flexible systems, including combustors and engines without significant sacrifice in performance or emissions requirements. This paper provides preliminary performance (Part A) and emissions and particulates (Part B) combustor sector data for synthetic-parafinic-kerosene- (SPK-) type fuel and blends with JP-8+100 relative to JP-8+100 as baseline fueling.

A study to define a set of requirements for cleansing agents for use in the Space Station whole body shower

NASA Technical Reports Server (NTRS)

1985-01-01

The objective of this research is to define a set of requirements for a whole body cleansing agent to be used in the Space Station Whole Body Shower System. In addition, cleansing agent candidates are to be identified that are likely to satisfy requirements defined in the first part of the study. It is understood that the main reason for having a Whole Body Shower is to satisfy the physiological, psychological and social needs of the crew throughout the duration of duty in the Space Station. The cleansing agent must also be compatible with the vortex water/gas separator and the water reclamation system. To accomplish these goals the study was divided into six tasks.

On the Effective Construction of Compactly Supported Wavelets Satisfying Homogenous Boundary Conditions on the Interval

NASA Technical Reports Server (NTRS)

Chiavassa, G.; Liandrat, J.

1996-01-01

We construct compactly supported wavelet bases satisfying homogeneous boundary conditions on the interval (0,1). The maximum features of multiresolution analysis on the line are retained, including polynomial approximation and tree algorithms. The case of H(sub 0)(sup 1)(0, 1)is detailed, and numerical values, required for the implementation, are provided for the Neumann and Dirichlet boundary conditions.

47 CFR 68.316 - Hearing aid compatibility: Technical requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... selection of equipment options, of satisfying the requirements applicable to its marketing area. 2.3The... telephones, e.g., proprietary or digital telephones, an appropriate feed circuit and termination shall be...

14 CFR 417.121 - Safety critical preflight operations.

Code of Federal Regulations, 2011 CFR

2011-01-01

... must satisfy the requirements of § 417.307(b). (i) Unguided suborbital rocket preflight operations. For the launch of an unguided suborbital rocket, in addition to meeting the other requirements of this...

14 CFR 417.121 - Safety critical preflight operations.

Code of Federal Regulations, 2013 CFR

2013-01-01

... must satisfy the requirements of § 417.307(b). (i) Unguided suborbital rocket preflight operations. For the launch of an unguided suborbital rocket, in addition to meeting the other requirements of this...

14 CFR 417.121 - Safety critical preflight operations.

Code of Federal Regulations, 2010 CFR

2010-01-01

... must satisfy the requirements of § 417.307(b). (i) Unguided suborbital rocket preflight operations. For the launch of an unguided suborbital rocket, in addition to meeting the other requirements of this...

14 CFR 417.121 - Safety critical preflight operations.

Code of Federal Regulations, 2014 CFR

2014-01-01

... must satisfy the requirements of § 417.307(b). (i) Unguided suborbital rocket preflight operations. For the launch of an unguided suborbital rocket, in addition to meeting the other requirements of this...

14 CFR 417.121 - Safety critical preflight operations.

Code of Federal Regulations, 2012 CFR

2012-01-01

... must satisfy the requirements of § 417.307(b). (i) Unguided suborbital rocket preflight operations. For the launch of an unguided suborbital rocket, in addition to meeting the other requirements of this...

40 CFR 63.1354 - Reporting requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

... the Administrator a copy of the report sent to the State to satisfy the requirements of this section..., you must submit reports to the EPA's WebFIRE database by using the Compliance and Emissions Data...

40 CFR 63.1354 - Reporting requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

... the Administrator a copy of the report sent to the State to satisfy the requirements of this section..., you must submit reports to the EPA's WebFIRE database by using the Compliance and Emissions Data...

43 CFR 3105.2-3 - Requirements.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 43 Public Lands: Interior 2 2013-10-01 2013-10-01 false Requirements. 3105.2-3 Section 3105.2-3... § 3105.2-3 Requirements. (a) The communitization or drilling agreement shall describe the separate tracts... order. (c) The public interest requirement for an approved communitization agreement shall be satisfied...

43 CFR 3105.2-3 - Requirements.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 43 Public Lands: Interior 2 2012-10-01 2012-10-01 false Requirements. 3105.2-3 Section 3105.2-3... § 3105.2-3 Requirements. (a) The communitization or drilling agreement shall describe the separate tracts... order. (c) The public interest requirement for an approved communitization agreement shall be satisfied...

43 CFR 3105.2-3 - Requirements.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 43 Public Lands: Interior 2 2014-10-01 2014-10-01 false Requirements. 3105.2-3 Section 3105.2-3... § 3105.2-3 Requirements. (a) The communitization or drilling agreement shall describe the separate tracts... order. (c) The public interest requirement for an approved communitization agreement shall be satisfied...

13 CFR 108.150 - Management and ownership diversity requirement.

Code of Federal Regulations, 2014 CFR

2014-01-01

...” Institutional Investor may be substituted for two or three of the three investors who are otherwise required. The following Institutional Investors are “acceptable” for this purpose: (1) Entities whose overall... Investors satisfactory to SBA. (d) Voting requirement. The investors required for you to satisfy diversity...

13 CFR 108.150 - Management and ownership diversity requirement.

Code of Federal Regulations, 2013 CFR

2013-01-01

...” Institutional Investor may be substituted for two or three of the three investors who are otherwise required. The following Institutional Investors are “acceptable” for this purpose: (1) Entities whose overall... Investors satisfactory to SBA. (d) Voting requirement. The investors required for you to satisfy diversity...

13 CFR 108.150 - Management and ownership diversity requirement.

Code of Federal Regulations, 2012 CFR

2012-01-01

...” Institutional Investor may be substituted for two or three of the three investors who are otherwise required. The following Institutional Investors are “acceptable” for this purpose: (1) Entities whose overall... Investors satisfactory to SBA. (d) Voting requirement. The investors required for you to satisfy diversity...

13 CFR 108.150 - Management and ownership diversity requirement.

Code of Federal Regulations, 2011 CFR

2011-01-01

...” Institutional Investor may be substituted for two or three of the three investors who are otherwise required. The following Institutional Investors are “acceptable” for this purpose: (1) Entities whose overall... Investors satisfactory to SBA. (d) Voting requirement. The investors required for you to satisfy diversity...

20 CFR 655.17 - Advertising requirements.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 20 Employees' Benefits 3 2012-04-01 2012-04-01 false Advertising requirements. 655.17 Section 655... Advertising requirements. All advertising conducted to satisfy the required recruitment steps under § 655.15... those to be offered to the H-2B workers. All advertising must contain the following information: (a) The...

Readout Electronics for the Central Drift Chamber of the Belle-II Detector

NASA Astrophysics Data System (ADS)

Uchida, Tomohisa; Taniguchi, Takashi; Ikeno, Masahiro; Iwasaki, Yoshihito; Saito, Masatoshi; Shimazaki, Shoichi; Tanaka, Manobu M.; Taniguchi, Nanae; Uno, Shoji

2015-08-01

We have developed readout electronics for the central drift chamber (CDC) of the Belle-II detector. The space near the endplate of the CDC for installation of the electronics was limited by the detector structure. Due to the large amounts of data generated by the CDC, a high-speed data link, with a greater than one gigabit transfer rate, was required to transfer the data to a back-end computer. A new readout module was required to satisfy these requirements. This module processes 48 signals from the CDC, converts them to digital data and transfers it directly to the computer. All functions that transfer digital data via the high speed link were implemented on the single module. We have measured its electrical characteristics and confirmed that the results satisfy the requirements of the Belle-II experiment.

"BreastfeedingBasics": web-based education that meets current knowledge competencies.

PubMed

Lewin, Linda Orkin; O'Connor, Mary E

2012-08-01

The United States has not met the majority of the Centers for Disease Control and Prevention goals for breastfeeding duration. Studies have shown a lack of knowledge about breastfeeding by health care professionals and students (HCP/S). Web-based education can be a cost-effective manner of education for HCP/S. "BreastfeedingBasics" is an online free educational program available for use. This study compares information in "BreastfeedingBasics" to the breastfeeding knowledge competencies recommended by the US Breastfeeding Committee (USBC). It also evaluates usage of "BreastfeedingBasics" by users and health care professional faculty. Using anonymous information from Web site users, the authors compared mean pre-test and post-test scores of the modules as a measure of the knowledge gained by HCP/S users. They evaluated usage by demographic information and used a Web-based survey to assess benefits of usage of "BreastfeedingBasics" to faculty. Overall, 15 020 HCP/S used the Web site between April 1999 and December 2009. "BreastfeedingBasics" meets 8 of the 11 USBC knowledge competencies. Mean post-test scores increased (P < .001) for all modules. Faculty reported its benefits to be free, broad scope, and the ability to be completed on the students' own time; 84% of the faculty combined the use of "BreastfeedingBasics" with clinical work. Use of "BreastfeedingBasics" can help HCP/S meet the USBC core breastfeeding knowledge competencies and gain knowledge. Faculty are satisfied with its use. Wider use of "BreastfeedingBasics" to help improve the knowledge of HCP/S may help in improving breastfeeding outcomes.

12 CFR 204.121 - Bankers' banks.

Code of Federal Regulations, 2010 CFR

2010-01-01

... time deposits. Under section 19(b)(9), however, a depository institution is not required to maintain... depository institutions; directors, officers or employees of the same or other depository institutions... required to satisfy Federal reserve requirements on all of its transaction accounts and nonpersonal time...

Associations between state regulations, training length, perceived quality and job satisfaction among certified nursing assistants: cross-sectional secondary data analysis.

PubMed

Han, Kihye; Trinkoff, Alison M; Storr, Carla L; Lerner, Nancy; Johantgen, Meg; Gartrell, Kyungsook

2014-08-01

In the U.S., there are federal requirements on how much training and annual continuing education a certified nursing assistant must complete in order to be certified. The requirements are designed to enable them to provide competent and quality care to nursing home residents. Many states also require additional training and continuing education hours as improved nursing home quality indicators have been found to be related to increased training. This study investigated the associations among state level regulations, initial training quality and focus, and job satisfaction in certified nursing assistants. Cross-sectional secondary data analysis. This study used the National Nursing Home Survey and National Nursing Assistant Survey as well as data on state regulations of certified nursing assistant training. 2897 certified nursing assistants in 580 nursing homes who were currently working at a nursing home facility, who represented 680,846 certified nursing assistants in US. State regulations were related to initial training and job satisfaction among certified nursing assistants using chi square tests and binomial logistic regression models. Analyses were conducted using SAS-callable SUDAAN to correct for complex sampling design effects in the National Nursing Home Survey and National Nursing Assistant Survey. Models were adjusted for personal and facility characteristics. Certified nursing assistants reporting high quality training were more likely to work in states requiring additional initial training hours (p=0.02) and were more satisfied with their jobs (OR=1.51, 95% CI=1.09-2.09) than those with low quality training. In addition, those with more training focused on work life skills were 91% more satisfied (OR=1.91, 95% CI=1.41-2.58) whereas no relationship was found between training focused on basic care skills and job satisfaction (OR=1.36, 95% CI=0.99-1.84). Certified nursing assistants with additional initial training were more likely to report that their training was of high quality, and this was related to job satisfaction. Job satisfaction was also associated with receiving more training that focused on work life skills. Federal training regulations should reconsider additional hours for certified nursing assistant initial training, and include work life skills as a focus. As job satisfaction has been linked to nursing home turnover, attention to training may improve satisfaction, ultimately reducing staff turnover. Copyright © 2014 Elsevier Ltd. All rights reserved.

A Deadline-Aware Scheduling and Forwarding Scheme in Wireless Sensor Networks.

PubMed

Dao, Thi-Nga; Yoon, Seokhoon; Kim, Jangyoung

2016-01-05

Many applications in wireless sensor networks (WSNs) require energy consumption to be minimized and the data delivered to the sink within a specific delay. A usual solution for reducing energy consumption is duty cycling, in which nodes periodically switch between sleep and active states. By increasing the duty cycle interval, consumed energy can be reduced more. However, a large duty cycle interval causes a long end-to-end (E2E) packet delay. As a result, the requirement of a specific delay bound for packet delivery may not be satisfied. In this paper, we aim at maximizing the duty cycle while still guaranteeing that the packets arrive at the sink with the required probability, i.e., the required delay-constrained success ratio (DCSR) is achieved. In order to meet this objective, we propose a novel scheduling and forwarding scheme, namely the deadline-aware scheduling and forwarding (DASF) algorithm. In DASF, the E2E delay distribution with the given network model and parameters is estimated in order to determine the maximum duty cycle interval, with which the required DCSR is satisfied. Each node independently selects a wake-up time using the selected interval, and packets are forwarded to a node in the potential forwarding set, which is determined based on the distance between nodes and the sink. DASF does not require time synchronization between nodes, and a node does not need to maintain neighboring node information in advance. Simulation results show that the proposed scheme can satisfy a required delay-constrained success ratio and outperforms existing algorithms in terms of E2E delay and DCSR.

A Deadline-Aware Scheduling and Forwarding Scheme in Wireless Sensor Networks

PubMed Central

Dao, Thi-Nga; Yoon, Seokhoon; Kim, Jangyoung

2016-01-01

Many applications in wireless sensor networks (WSNs) require energy consumption to be minimized and the data delivered to the sink within a specific delay. A usual solution for reducing energy consumption is duty cycling, in which nodes periodically switch between sleep and active states. By increasing the duty cycle interval, consumed energy can be reduced more. However, a large duty cycle interval causes a long end-to-end (E2E) packet delay. As a result, the requirement of a specific delay bound for packet delivery may not be satisfied. In this paper, we aim at maximizing the duty cycle while still guaranteeing that the packets arrive at the sink with the required probability, i.e., the required delay-constrained success ratio (DCSR) is achieved. In order to meet this objective, we propose a novel scheduling and forwarding scheme, namely the deadline-aware scheduling and forwarding (DASF) algorithm. In DASF, the E2E delay distribution with the given network model and parameters is estimated in order to determine the maximum duty cycle interval, with which the required DCSR is satisfied. Each node independently selects a wake-up time using the selected interval, and packets are forwarded to a node in the potential forwarding set, which is determined based on the distance between nodes and the sink. DASF does not require time synchronization between nodes, and a node does not need to maintain neighboring node information in advance. Simulation results show that the proposed scheme can satisfy a required delay-constrained success ratio and outperforms existing algorithms in terms of E2E delay and DCSR. PMID:26742046

46 CFR 38.05-1 - Design and construction of vessels-general-TB/ALL.

Code of Federal Regulations, 2010 CFR

2010-10-01

... system shall satisfy the requirements for toughness specified in subchapter F (Marine Engineering) of... secondary barrier is required, the material of that barrier and of contiguous hull structure shall have...

32 CFR Appendix to Part 162 - Reporting Procedures

Code of Federal Regulations, 2010 CFR

2010-07-01

... PECI reporting requirements provide the OSD with summary information required to provide program accountability, and satisfy the congressional concerns on program management. Information may be submitted in memorandum, letter, or other acceptable form. B. Information Requirements 1. PIF. Each DoD Component that has...

Compact Plasma Accelerator for Micropropulsion Applications

NASA Technical Reports Server (NTRS)

Foster, John E.

2001-01-01

There is a need for a low power, light-weight (compact), high specific impulse electric propulsion device to satisfy mission requirements for microsatellite (1 to 20 kg) class missions. Satisfying these requirements entails addressing the general problem of generating a sufficiently dense plasma within a relatively small volume and then accelerating it. In the work presented here, the feasibility of utilizing a magnetic cusp to generate a dense plasma over small length scales of order 1 mm is investigated. This approach could potentially mitigate scaling issues associated with conventional ion thruster plasma containment schemes. Plume and discharge characteristics were documented using a Faraday probe and a retarding potential analyzer.

Determination of ASPS performance for large payloads in the shuttle orbiter disturbance environment. [digital simulation

NASA Technical Reports Server (NTRS)

Keckler, C. R.; Kibler, K. S.; Powell, L. F.

1979-01-01

A high fidelity simulation of the annular suspension and pointing system (ASPS), its payload, and the shuttle orbiter was used to define the worst case orientations of the ASPS and its payload for the various vehicle disturbances, and to determine the performance capability of the ASPS under these conditions. The most demanding and largest proposed payload, the Solar Optical Telescope was selected for study. It was found that, in all cases, the ASPS more than satisfied the payload's requirements. It is concluded that, to satisfy facility class payload requirements, the ASPS or a shuttle orbiter free-drift mode (control system off) should be utilized.

Gupta-Bleuler Quantization of the Maxwell Field in Globally Hyperbolic Space-Times

NASA Astrophysics Data System (ADS)

Finster, Felix; Strohmaier, Alexander

2015-08-01

We give a complete framework for the Gupta-Bleuler quantization of the free electromagnetic field on globally hyperbolic space-times. We describe one-particle structures that give rise to states satisfying the microlocal spectrum condition. The field algebras in the so-called Gupta-Bleuler representations satisfy the time-slice axiom, and the corresponding vacuum states satisfy the microlocal spectrum condition. We also give an explicit construction of ground states on ultrastatic space-times. Unlike previous constructions, our method does not require a spectral gap or the absence of zero modes. The only requirement, the absence of zero-resonance states, is shown to be stable under compact perturbations of topology and metric. Usual deformation arguments based on the time-slice axiom then lead to a construction of Gupta-Bleuler representations on a large class of globally hyperbolic space-times. As usual, the field algebra is represented on an indefinite inner product space, in which the physical states form a positive semi-definite subspace. Gauge transformations are incorporated in such a way that the field can be coupled perturbatively to a Dirac field. Our approach does not require any topological restrictions on the underlying space-time.

Prediction of plasma properties in mercury ion thrusters

NASA Technical Reports Server (NTRS)

Longhurst, G. R.

1978-01-01

A simplified theoretical model was developed which obtains to first order the plasma properties in the discharge chamber of a mercury ion thruster from basic thruster design and controllable operating parameters. The basic operation and design of ion thrusters is discussed, and the important processes which influence the plasma properties are described in terms of the design and control parameters. The conservation for mass, charge and energy were applied to the ion production region, which was defined as the region of the discharge chamber having as its outer boundary the surface of revolution of the innermost field line to intersect the anode. Mass conservation and the equations describing the various processes involved with mass addition and removal from the ion production region are satisfied by a Maxwellian electron density spatial distribution in that region.

What Are We Waiting For Customer Wait Time, Fill Rate, And Marine Corps Equipment Operational Availability

DTIC Science & Technology

2016-12-01

managed by an RIP. SECREPs are typically critical repair assemblies that require consistently high fill- rates to satisfy maintenance customers ...fill-rate is potentially misreporting performance and areas where short customer wait times could potentially suffice for inventory management . A...supply. Inventory forecasting and management should focus on parts with CWTs that do not satisfy the maintenance customer and 100% fill-rates should

Unsupervised domain adaptation for early detection of drought stress in hyperspectral images

NASA Astrophysics Data System (ADS)

Schmitter, P.; Steinrücken, J.; Römer, C.; Ballvora, A.; Léon, J.; Rascher, U.; Plümer, L.

2017-09-01

Hyperspectral images can be used to uncover physiological processes in plants if interpreted properly. Machine Learning methods such as Support Vector Machines (SVM) and Random Forests have been applied to estimate development of biomass and detect and predict plant diseases and drought stress. One basic requirement of machine learning implies, that training and testing is done in the same domain and the same distribution. Different genotypes, environmental conditions, illumination and sensors violate this requirement in most practical circumstances. Here, we present an approach, which enables the detection of physiological processes by transferring the prior knowledge within an existing model into a related target domain, where no label information is available. We propose a two-step transformation of the target features, which enables a direct application of an existing model. The transformation is evaluated by an objective function including additional prior knowledge about classification and physiological processes in plants. We have applied the approach to three sets of hyperspectral images, which were acquired with different plant species in different environments observed with different sensors. It is shown, that a classification model, derived on one of the sets, delivers satisfying classification results on the transformed features of the other data sets. Furthermore, in all cases early non-invasive detection of drought stress was possible.

Validation of software for calculating the likelihood ratio for parentage and kinship.

PubMed

Drábek, J

2009-03-01

Although the likelihood ratio is a well-known statistical technique, commercial off-the-shelf (COTS) software products for its calculation are not sufficiently validated to suit general requirements for the competence of testing and calibration laboratories (EN/ISO/IEC 17025:2005 norm) per se. The software in question can be considered critical as it directly weighs the forensic evidence allowing judges to decide on guilt or innocence or to identify person or kin (i.e.: in mass fatalities). For these reasons, accredited laboratories shall validate likelihood ratio software in accordance with the above norm. To validate software for calculating the likelihood ratio in parentage/kinship scenarios I assessed available vendors, chose two programs (Paternity Index and familias) for testing, and finally validated them using tests derived from elaboration of the available guidelines for the field of forensics, biomedicine, and software engineering. MS Excel calculation using known likelihood ratio formulas or peer-reviewed results of difficult paternity cases were used as a reference. Using seven testing cases, it was found that both programs satisfied the requirements for basic paternity cases. However, only a combination of two software programs fulfills the criteria needed for our purpose in the whole spectrum of functions under validation with the exceptions of providing algebraic formulas in cases of mutation and/or silent allele.

Latest Progress In Novel High Conductivity And Highly Stable Composite Structure Developments For Satellite Applications

NASA Astrophysics Data System (ADS)

Klebor, Maximillian; Reichmann, Olaf; Pfeiffer, Ernst K.; Ihle, Alexander; Linke, Stefan; Tschepe, Christoph; Roddecke, Susanne; Richter, Ines; Berrill, Mark; Santiago-Prowald, Julian

2012-07-01

Materials such as aluminium, titanium and carbon fibre based composites are indispensable in space business. However, special demands on spaceborne applications require both new ideas and new concepts but also powerful novel materials. These days the trend is to substitute aluminium for CFRP basically in order to safe mass or to decrease thermal expansions. Nevertheless there are upcoming requirements that cannot be met using standard CFRP materials. In this connection innovative composites have to be introduced. In the frame of this paper three major applications for such material requests are considered, i.e.: • antennas • satellite platform structural panels • radiators. The new composites need to cope with the following challenges and demands: high operational temperature range, high stiffness, high strength, high thermal conductivity, vacuum compatibility, low mass, high in- orbit stability, compatibility with metallic parts and many more. Some of these demands have to be fulfilled in conjunction. Herein the innovative composites cover new raw materials and their combination, manufacturing process enhancement as well as new inspection and test methods. It has been observed that by using the developed CFRPs it is possible to satisfy and excel the needs. However, these materials feature a different behaviour than conventional composites which has to be taken into account during future design.

The CEOS-Land Surface Imaging Constellation Portal for GEOSS: A resource for land surface imaging system information and data access

USGS Publications Warehouse

Holm, Thomas; Gallo, Kevin P.; Bailey, Bryan

2010-01-01

The Committee on Earth Observation Satellites is an international group that coordinates civil space-borne observations of the Earth, and provides the space component of the Global Earth Observing System of Systems (GEOSS). The CEOS Virtual Constellations concept was implemented in an effort to engage and coordinate disparate Earth observing programs of CEOS member agencies and ultimately facilitate their contribution in supplying the space-based observations required to satisfy the requirements of the GEOSS. The CEOS initially established Study Teams for four prototype constellations that included precipitation, land surface imaging, ocean surface topography, and atmospheric composition. The basic mission of the Land Surface Imaging (LSI) Constellation [1] is to promote the efficient, effective, and comprehensive collection, distribution, and application of space-acquired image data of the global land surface, especially to meet societal needs of the global population, such as those addressed by the nine Group on Earth Observations (GEO) Societal Benefit Areas (SBAs) of agriculture, biodiversity, climate, disasters, ecosystems, energy, health, water, and weather. The LSI Constellation Portal is the result of an effort to address important goals within the LSI Constellation mission and provide resources to assist in planning for future space missions that might further contribute to meeting those goals.

Basic Values, Career Orientations, and Career Anchors: Empirical Investigation of Relationships

PubMed Central

Abessolo, Marc; Rossier, Jérôme; Hirschi, Andreas

2017-01-01

In today's dynamic and uncertain career context, values play an important role for career choice and lifelong career self-management. Values are desirable goals that are sought by individuals to satisfy their needs and are important for understanding career orientations in terms of protean and boundaryless career orientations and career anchors. However, how career orientations or career anchors fit into a well-established and supported model and into the structure of basic human values remains an important and under-investigated question. The aim of this study was to use Schwartz's model of structural values to empirically explore the relationships and structural correspondences among basic values, career orientations, and career anchors. A heterogeneous sample of 238 employees from French-speaking Switzerland (Mage = 35.60, SD = 13.03) completed the Portrait Values Questionnaire (PVQ5X), the Protean and Boundaryless Career Attitudes Scales (PCAS, BCAS), and the Career Orientation Inventory (COI) via an anonymous and confidential survey questionnaire. The results showed that it was possible to meaningfully position both career orientations and career anchors in Schwartz's values structure. The protean and boundaryless career orientations were positively related to Schwartz's basic values that emphasized openness to change and career anchors meaningfully followed the motivational continuum of these basic values. Overall, the overlap among the basic values, career orientations, and career anchors appeared relatively important, suggesting that these basic values, orientations, and anchors should be considered simultaneously to understand and address the factors and processes underlying individuals' career choices and paths. PMID:28955275

Basic Values, Career Orientations, and Career Anchors: Empirical Investigation of Relationships.

PubMed

Abessolo, Marc; Rossier, Jérôme; Hirschi, Andreas

2017-01-01

In today's dynamic and uncertain career context, values play an important role for career choice and lifelong career self-management. Values are desirable goals that are sought by individuals to satisfy their needs and are important for understanding career orientations in terms of protean and boundaryless career orientations and career anchors. However, how career orientations or career anchors fit into a well-established and supported model and into the structure of basic human values remains an important and under-investigated question. The aim of this study was to use Schwartz's model of structural values to empirically explore the relationships and structural correspondences among basic values, career orientations, and career anchors. A heterogeneous sample of 238 employees from French-speaking Switzerland (Mage = 35.60, SD = 13.03) completed the Portrait Values Questionnaire (PVQ5X), the Protean and Boundaryless Career Attitudes Scales (PCAS, BCAS), and the Career Orientation Inventory (COI) via an anonymous and confidential survey questionnaire. The results showed that it was possible to meaningfully position both career orientations and career anchors in Schwartz's values structure. The protean and boundaryless career orientations were positively related to Schwartz's basic values that emphasized openness to change and career anchors meaningfully followed the motivational continuum of these basic values. Overall, the overlap among the basic values, career orientations, and career anchors appeared relatively important, suggesting that these basic values, orientations, and anchors should be considered simultaneously to understand and address the factors and processes underlying individuals' career choices and paths.

42 CFR 66.205 - Requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 42 Public Health 1 2010-10-01 2010-10-01 false Requirements. 66.205 Section 66.205 Public Health... NATIONAL RESEARCH SERVICE AWARDS Institutional Grants § 66.205 Requirements. (a) No Award shall be made to... the form and manner the Secretary may prescribe, that he or she will satisfy the requirements of § 66...

42 CFR 66.205 - Requirements.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 42 Public Health 1 2011-10-01 2011-10-01 false Requirements. 66.205 Section 66.205 Public Health... NATIONAL RESEARCH SERVICE AWARDS Institutional Grants § 66.205 Requirements. (a) No Award shall be made to... the form and manner the Secretary may prescribe, that he or she will satisfy the requirements of § 66...

42 CFR 483.150 - Statutory basis; Deemed meeting or waiver of requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... CARE FACILITIES Requirements That Must Be Met by States and State Agencies: Nurse Aide Training and... 1919(f)(2) of the Act, which establish standards for training nurse-aides and for evaluating their competency. (b) Deemed meeting of requirements. A nurse aide is deemed to satisfy the requirement of...

47 CFR 80.753 - Signal strength requirements at the service area contour.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 47 Telecommunication 5 2010-10-01 2010-10-01 false Signal strength requirements at the service... Station VHF Coverage § 80.753 Signal strength requirements at the service area contour. (a) The requirements for reception by a marine VHF shipboard receiver are satisfied if the field strength from the...

47 CFR 80.753 - Signal strength requirements at the service area contour.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 47 Telecommunication 5 2011-10-01 2011-10-01 false Signal strength requirements at the service... Station VHF Coverage § 80.753 Signal strength requirements at the service area contour. (a) The requirements for reception by a marine VHF shipboard receiver are satisfied if the field strength from the...

42 CFR 417.472 - Basic contract requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 42 Public Health 3 2010-10-01 2010-10-01 false Basic contract requirements. 417.472 Section 417.472 Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT OF HEALTH AND HUMAN SERVICES... PREPAYMENT PLANS Medicare Contract Requirements § 417.472 Basic contract requirements. (a) Submittal of...

Reduction of aircraft gas turbine engine pollutant emissions

NASA Technical Reports Server (NTRS)

Diehl, L. A.

1978-01-01

To accomplish simultaneous reduction of unburned hydrocarbons, carbon monoxide, and oxides of nitrogen, required major modifications to the combustor. The modification most commonly used was a staged combustion technique. While these designs are more complicated than production combustors, no insurmountable operational difficulties were encountered in either high pressure rig or engine tests which could not be resolved with additional normal development. The emission reduction results indicate that reductions in unburned hydrocarbons were sufficient to satisfy both near and far-termed EPA requirements. Although substantial reductions were observed, the success in achieving the CO and NOx standards was mixed and depended heavily on the engine/engine cycle on which it was employed. Technology for near term CO reduction was satisfactory or marginally satisfactory. Considerable doubt exists if this technology will satisfy all far-term requirements.

How gauge covariance of the fermion and boson propagators in QED constrain the effective fermion-boson vertex

DOE PAGES

Jia, Shaoyang; Pennington, M. R.

2016-12-12

In this paper, we derive the gauge covariance requirement imposed on the QED fermion-photon three-point function within the framework of a spectral representation for fermion propagators. When satisfied, such requirement ensures solutions to the fermion propagator Schwinger-Dyson equation (SDE) in any covariant gauge with arbitrary numbers of spacetime dimensions to be consistent with the Landau-Khalatnikov-Fradkin transformation (LKFT). The general result has been verified by the special cases of three and four dimensions. Additionally, we present the condition that ensures the vacuum polarization is independent of the gauge parameter. Finally, as an illustration, we show how the gauge technique dimensionally regularizedmore » in four dimensions does not satisfy the covariance requirement.« less

40 CFR 62.14463 - What reporting requirements must I satisfy?

Code of Federal Regulations, 2010 CFR

2010-07-01

... POLLUTANTS Federal Plan Requirements for Hospital/Medical/Infectious Waste Incinerators Constructed on or....14453, as applicable; (c) The waste management plan as specified in § 62.14431; (d) The highest maximum... (k) Records of the annual equipment inspections, any required maintenance, and any repairs not...

Standby power for railroad-highway grade crossing warning systems

DOT National Transportation Integrated Search

1976-09-30

The requirements for standby power at railroad-highway grade crossings, as established by the states, the Association of American Railroads, and the individual railroads, are described. Standard means of satisfying these requirements, using 115 vac p...

Curvature tensors unified field equations on SEXn

NASA Astrophysics Data System (ADS)

Chung, Kyung Tae; Lee, Il Young

1988-09-01

We study the curvature tensors and field equations in the n-dimensional SE manifold SEXn. We obtain several basic properties of the vectors S λ and U λ and then of the SE curvature tensor and its contractions, such as a generalized Ricci identity, a generalized Bianchi identity, and two variations of the Bianchi identity satisfied by the SE Einstein tensor. Finally, a system of field equations is discussed in SEXn and one of its particular solutions is constructed and displayed.

Measurement and control of a Coulomb-blockaded parafermion box

NASA Astrophysics Data System (ADS)

Snizhko, Kyrylo; Egger, Reinhold; Gefen, Yuval

2018-02-01

Parafermionic zero modes are fractional topologically protected quasiparticles expected to arise in various platforms. We show that Coulomb charging effects define a parafermion box with unique access options via fractional edge states and/or quantum antidots. Basic protocols for the detection, manipulation, and control of parafermionic quantum states are formulated. With those tools, one may directly observe the dimension of the zero-mode Hilbert space, prove the degeneracy of this space, and perform on-demand digital operations satisfying a parafermionic algebra.

EHV systems technology - A look at the principles and current status. [Electric and Hybrid Vehicle

NASA Technical Reports Server (NTRS)

Kurtz, D. W.; Levin, R. R.

1983-01-01

An examination of the basic principles and practices of systems engineering is undertaken in the context of their application to the component and subsystem technologies involved in electric and hybrid vehicle (EHV) development. The limitations of purely electric vehicles are contrasted with hybrid, heat engine-incorporating vehicle technology, which is inherently more versatile. A hybrid vehicle concept assessment methodology is presented which employs current technology and yet fully satisfies U.S. Department of Energy petroleum displacement goals.

USGS Research on Saline Waters Co-Produced with Energy Resources

USGS Publications Warehouse

,

1997-01-01

The United States energy industry faces the challenge of satisfying our expanding thirst for energy while protecting the environment. This challenge is magnified by the increasing volumes of saline water produced with oil and gas in the Nation's aging petroleum fields. Ultimately, energy-producing companies are responsible for disposing of these waters. USGS research provides basic information, for use by regulators, industry, and the public, about the chemistry of co-produced waters and environmentally acceptable ways of handling them.

Practical quality control tools for curves and surfaces

NASA Technical Reports Server (NTRS)

Small, Scott G.

1992-01-01

Curves (geometry) and surfaces created by Computer Aided Geometric Design systems in the engineering environment must satisfy two basic quality criteria: the geometric shape must have the desired engineering properties; and the objects must be parameterized in a way which does not cause computational difficulty for geometric processing and engineering analysis. Interactive techniques are described which are in use at Boeing to evaluate the quality of aircraft geometry prior to Computational Fluid Dynamic analysis, including newly developed methods for examining surface parameterization and its effects.

Optimization of Maneuver Execution for Landsat-7 Routine Operations

NASA Technical Reports Server (NTRS)

Cox, E. Lucien, Jr.; Bauer, Frank H. (Technical Monitor)

2000-01-01

Multiple mission constraints were satisfied during a lengthy, strategic ascent phase. Once routine operations begin, the ongoing concern of maintaining mission requirements becomes an immediate priority. The Landsat-7 mission has tight longitude control box and Earth imaging that requires sub-satellite descending nodal equator crossing times to occur in a narrow 30minute range fifteen (15) times daily. Operationally, spacecraft maneuvers must'be executed properly to maintain mission requirements. The paper will discuss the importance of optimizing the altitude raising and plane change maneuvers, amidst known constraints, to satisfy requirements throughout mission lifetime. Emphasis will be placed not only on maneuver size and frequency but also on changes in orbital elements that impact maneuver execution decisions. Any associated trade-off arising from operations contingencies will be discussed as well. Results of actual altitude and plane change maneuvers are presented to clarify actions taken.

Personnel scheduling using an integer programming model- an application at Avanti Blue-Nile Hotels.

PubMed

Kassa, Biniyam Asmare; Tizazu, Anteneh Eshetu

2013-01-01

In this paper, we report perhaps a first of its kind application of management science in the Ethiopian hotel industry. Avanti Blue Nile Hotels, a newly established five star hotel in Bahir Dar, is the company for which we developed an integer programming model that determines an optimal weekly shift schedule for the Hotel's engineering department personnel while satisfying several constraints including weekly rest requirements per employee, rest requirements between working shifts per employee, required number of personnel per shift, and other constraints. The model is implemented on an excel solver routine. The model enables the company's personnel department management to develop a fair personnel schedule as needed and to effectively utilize personnel resources while satisfying several technical, legal and economic requirements. These encouraging achievements make us optimistic about the gains other Ethiopian organizations can amass by introducing management science approaches in their management planning and decision making systems.

A Brownian dynamics study on ferrofluid colloidal dispersions using an iterative constraint method to satisfy Maxwell’s equations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dubina, Sean Hyun, E-mail: sdubin2@uic.edu; Wedgewood, Lewis Edward, E-mail: wedge@uic.edu

2016-07-15

Ferrofluids are often favored for their ability to be remotely positioned via external magnetic fields. The behavior of particles in ferromagnetic clusters under uniformly applied magnetic fields has been computationally simulated using the Brownian dynamics, Stokesian dynamics, and Monte Carlo methods. However, few methods have been established that effectively handle the basic principles of magnetic materials, namely, Maxwell’s equations. An iterative constraint method was developed to satisfy Maxwell’s equations when a uniform magnetic field is imposed on ferrofluids in a heterogeneous Brownian dynamics simulation that examines the impact of ferromagnetic clusters in a mesoscale particle collection. This was accomplished bymore » allowing a particulate system in a simple shear flow to advance by a time step under a uniformly applied magnetic field, then adjusting the ferroparticles via an iterative constraint method applied over sub-volume length scales until Maxwell’s equations were satisfied. The resultant ferrofluid model with constraints demonstrates that the magnetoviscosity contribution is not as substantial when compared to homogeneous simulations that assume the material’s magnetism is a direct response to the external magnetic field. This was detected across varying intensities of particle-particle interaction, Brownian motion, and shear flow. Ferroparticle aggregation was still extensively present but less so than typically observed.« less

The AmeriFlux Data Activity and Data System: An Evolving Collection of Data Management Techniques, Tools, Products and Services

DOE Office of Scientific and Technical Information (OSTI.GOV)

Boden, Thomas A; Krassovski, Misha B; Yang, Bai

2013-01-01

The Carbon Dioxide Information Analysis Center (CDIAC) at Oak Ridge National Laboratory (ORNL), USA has provided scientific data management support for the U.S. Department of Energy and international climate change science since 1982. Over this period, climate change science has expanded from research focusing on basic understanding of geochemical cycles, particularly the carbon cycle, to integrated research addressing climate change impacts, vulnerability, adaptation, and mitigation. Interests in climate change data and information worldwide have grown remarkably and, as a result, so have demands and expectations for CDIAC s data systems. To meet the growing demands, CDIAC s strategy has beenmore » to design flexible data systems using proven technologies blended with new, evolving technologies and standards. CDIAC development teams are multidisciplinary and include computer science and information technology expertise, but also scientific expertise necessary to address data quality and documentation issues and to identify data products and system capabilities needed by climate change scientists. CDIAC has learned there is rarely a single commercial tool or product readily available to satisfy long-term scientific data system requirements (i.e., one size does not fit all and the breadth and diversity of environmental data are often too complex for easy use with commercial products) and typically deploys a variety of tools and data products in an effort to provide credible data freely to users worldwide. Like many scientific data management applications, CDIAC s data systems are highly customized to satisfy specific scientific usage requirements (e.g., developing data products specific for model use) but are also designed to be flexible and interoperable to take advantage of new software engineering techniques, standards (e.g., metadata standards) and tools and to support future Earth system data efforts (e.g., ocean acidification). CDIAC has provided data management support for numerous long-term measurement projects crucial to climate change science. One current example is the AmeriFlux measurement network. AmeriFlux provides continuous measurements from forests, grasslands, wetlands, and croplands in North, Central, and South America and offers important insight about carbon cycling in terrestrial ecosystems. We share our approaches in satisfying the challenges of delivering AmeriFlux data worldwide to benefit others with similar challenges handling climate change data, further heighten awareness and use of an outstanding ecological data resource, and highlight expanded software engineering applications being used for climate change measurement data.« less

42 CFR 1007.5 - Basic requirement.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 42 Public Health 5 2010-10-01 2010-10-01 false Basic requirement. 1007.5 Section 1007.5 Public... STATE MEDICAID FRAUD CONTROL UNITS § 1007.5 Basic requirement. A State Medicaid fraud control unit must... requirements of §§ 1007.7 through 1007.13 of this part. ...

Preliminary design of an alternate high-temperature turbine. A topical report for Phase II of the High-Temperature-Turbine Technology Program

DOE Office of Scientific and Technical Information (OSTI.GOV)

Strough, R.I.

The feasibility of designing a convectively air-cooled turbine to operate in the environment of a 3000/sup 0/F combustor exit temperature with maximum turbine airfoil metal temperatures held to 1500/sup 0/F was established. The United Technologies-Kraftwerk Union V84.3 gas turbine design was used as the basic configuration for the design of the 3000/sup 0/F turbine. Turbine cooling requirements were determined based on the use of the modified V84.3 type silo combustor with a pattern factor of 0.1. The convective air-cooling technology levels in terms of cooling effectiveness required to satisfy the airfoil cooling requirements were identified. Cooling schemes and fabrication technologiesmore » required are discussed. Turbine airfoil cooling technology levels required for the 3000/sup 0/F engine were selected. The performance of the 3000/sup 0/F convectively air-cooled gas turbine in simple and combined cycle was calculated. The 3000/sup 0/F gas turbine combined-cycle system provides an increase in power of 61% and a decrease in heat rate of 10% compared to a similar system with a combustor exit temperature of 2210/sup 0/F and the same airflow. The development of a successful 3000/sup 0/F convectively air-cooled turbine can be accomplished with a reasonable design and fabrication development effort on the cooled turbine airfoils. Use of the convectively air-cooled turbine provides the transfer of technology from extensive aircraft engines developed programs and operating experience to industrial gas turbines. It eliminates the requirement for large investments in alternate cooling techniques tailored specifically for industrial engines which offer no additional benefits.« less

Piezo-Operated Shutter Mechanism Moves 1.5 cm

NASA Technical Reports Server (NTRS)

Glaser, Robert; Bamford, Robert

2005-01-01

The figure shows parts of a shutter mechanism designed to satisfy a number of requirements specific to its original intended application as a component of an atomic clock to be flown in outer space. The mechanism may also be suitable for use in laboratory and industrial vacuum systems on Earth for which there are similar requirements. The requirements include the following: a) To alternately close, then open, a 1.5-cm-diameter optical aperture twice per second, with a stroke time of no more than 15 ms, during a total operational lifetime of at least a year; b) To attenuate light by a factor of at least 1012 when in the closed position; c) To generate little or no magnetic field; d) To be capable of withstanding bakeout at a temperature of 200 C to minimize outgassing during subsequent operation in an ultrahigh vacuum; and e) To fit within a diameter of 12 in. (=305 mm) a size limit dictated by the size of an associated magnetic shield. The light-attenuation requirement is satisfied by use of overlapping shutter blades. The closure of the aperture involves, among other things, insertion of a single shutter blade between a pair of shutter blades. The requirement to minimize the magnetic field is satisfied by use of piezoelectric actuators. Because piezoelectric actuators cannot withstand bakeout, they must be mounted outside the vacuum chamber, and, hence, motion must be transmitted from the actuators to the shutter levers via a vacuum-chamber-wall diaphragm.

Safer work clothing for fishermen.

PubMed

Geving, Ingunn Holmen; Reitan, Jarl; Sandsund, Mariann; Faerevik, Hilde; Reinertsen, Randi Eidsmo; Aasjord, Halvard

2006-01-01

The fisherman's work environment consists of many potential risks. A study of occupational accidents in the Norwegian fishing industry in the nine-year period from 1998 to 2006 shows that more than 3/4 of the deaths were caused by loss of fishing vessel or man-overboard accidents. Furthermore, the greatest risk of drowning is found in the smallest fleet. The aim of our project was to develop safer work clothing and through this contribute to a reduction in work accidents and injuries in the fishing fleet. We considered that it is possible to produce protective work clothing that satisfies a specification of requirements covering the fishermen's needs for protection and comfort during work. An end user-centred process including twenty-three personal interviews and a questionnaire was used to clarify the fishermen's needs and wishes before detailed design and product development. We identified an overview of all the fishermen's needs for protection during work, and produced a prioritised list of functional requirements for the clothing. The results show that the clothing previously preferred by fishermen does not satisfy all the users' demands for safety, functionality and comfort. These demands have been taken into consideration when designing improved work clothing for the fishing fleet. A selected number of prototypes were developed on the basis of the established specification of requirements. The prototypes were evaluated according to the users' requirements through tests in SINTEF's Work Physiology Laboratory and on board fishing vessels. The results demonstrate that the new protective clothing satisfies the fishermen's requirements.

23 CFR 1340.3 - Basic design requirements.

Code of Federal Regulations, 2010 CFR

2010-04-01

... STATE OBSERVATIONAL SURVEYS OF SEAT BELT USE § 1340.3 Basic design requirements. Surveys conducted in... requirement. The sample identified for the survey shall have a probability-based design such that estimates... 23 Highways 1 2010-04-01 2010-04-01 false Basic design requirements. 1340.3 Section 1340.3...

23 CFR 1340.3 - Basic design requirements.

Code of Federal Regulations, 2011 CFR

2011-04-01

... STATE OBSERVATIONAL SURVEYS OF SEAT BELT USE § 1340.3 Basic design requirements. Surveys conducted in... requirement. The sample identified for the survey shall have a probability-based design such that estimates... 23 Highways 1 2011-04-01 2011-04-01 false Basic design requirements. 1340.3 Section 1340.3...

20 CFR 655.17 - Advertising requirements.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 20 Employees' Benefits 3 2011-04-01 2011-04-01 false Advertising requirements. 655.17 Section 655... States (H-2B Workers) § 655.17 Advertising requirements. All advertising conducted to satisfy the... employment which are not less favorable than those to be offered to the H-2B workers. All advertising must...

20 CFR 655.17 - Advertising requirements.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 20 Employees' Benefits 3 2010-04-01 2010-04-01 false Advertising requirements. 655.17 Section 655... States (H-2B Workers) § 655.17 Advertising requirements. All advertising conducted to satisfy the... employment which are not less favorable than those to be offered to the H-2B workers. All advertising must...

47 CFR 87.189 - Requirements for public correspondence equipment and operations.

Code of Federal Regulations, 2012 CFR

2012-10-01

... the Commission in conformity with part 87. Aircraft earth stations that are required to be commissioned to use a privately owned satellite system also must meet the provisions of § 87.51. (c) A... correspondence communications are being handled. For aircraft earth stations, this requirement is satisfied by...

47 CFR 87.189 - Requirements for public correspondence equipment and operations.

Code of Federal Regulations, 2014 CFR

2014-10-01

... the Commission in conformity with part 87. Aircraft earth stations that are required to be commissioned to use a privately owned satellite system also must meet the provisions of § 87.51. (c) A... correspondence communications are being handled. For aircraft earth stations, this requirement is satisfied by...

47 CFR 87.189 - Requirements for public correspondence equipment and operations.

Code of Federal Regulations, 2013 CFR

2013-10-01

... the Commission in conformity with part 87. Aircraft earth stations that are required to be commissioned to use a privately owned satellite system also must meet the provisions of § 87.51. (c) A... correspondence communications are being handled. For aircraft earth stations, this requirement is satisfied by...

Government Contractors and Sticky SGA Costs

DTIC Science & Technology

2015-04-30

supply generic products such as toothpaste which do not require satisfying unique federal requirements (and related paperwork). For these reasons... toothpaste . Proctor and Gamble may not need to deal with issues involving government-specific specifications and may have minimal incremental paperwork

Task Assignment Heuristics for Distributed CFD Applications

NASA Technical Reports Server (NTRS)

Lopez-Benitez, N.; Djomehri, M. J.; Biswas, R.; Biegel, Bryan (Technical Monitor)

2001-01-01

CFD applications require high-performance computational platforms: 1. Complex physics and domain configuration demand strongly coupled solutions; 2. Applications are CPU and memory intensive; and 3. Huge resource requirements can only be satisfied by teraflop-scale machines or distributed computing.

7 CFR 760.621 - Requirement to report acreage and production.

Code of Federal Regulations, 2010 CFR

2010-01-01

... counties. (b) Acreage and production reports that have been submitted to FSA for NAP or to RMA for crop... production submitted for NAP or FCIA purposes must satisfy the requirements of NAP or FCIA, as applicable. In...

40 CFR 63.1368 - Reporting requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

... of §§ 63.1362(h), 63.1365(h), 63.1366(g), and 63.1367(d) are satisfied. (l) Reports of heat exchange systems. The owner or operator of an affected source subject to the requirements for heat exchange systems...

40 CFR 63.1368 - Reporting requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... of § 63.1362(h), § 63.1365(h), § 63.1366(g), and § 63.1367(d) are satisfied. (l) Reports of heat exchange systems. The owner or operator of an affected source subject to the requirements for heat exchange...

Implementation Guidelines for State Safety Oversight of Rail Fixed Guideway Systems

DOT National Transportation Integrated Search

1996-06-01

These guidelines will assist states, oversight agencies, and rail transit agencies in developing safety and security programs to satisfy the requirements of the Federal Transit Administration (FTA). These requirements were published in the Federal Re...

Goals Analysis Procedure Guidelines for Applying the Goals Analysis Process

NASA Technical Reports Server (NTRS)

Motley, Albert E., III

2000-01-01

One of the key elements to successful project management is the establishment of the "right set of requirements", requirements that reflect the true customer needs and are consistent with the strategic goals and objectives of the participating organizations. A viable set of requirements implies that each individual requirement is a necessary element in satisfying the stated goals and that the entire set of requirements, taken as a whole, is sufficient to satisfy the stated goals. Unfortunately, it is the author's experience that during project formulation phases' many of the Systems Engineering customers do not conduct a rigorous analysis of the goals and objectives that drive the system requirements. As a result, the Systems Engineer is often provided with requirements that are vague, incomplete, and internally inconsistent. To complicate matters, most systems development methodologies assume that the customer provides unambiguous, comprehensive and concise requirements. This paper describes the specific steps of a Goals Analysis process applied by Systems Engineers at the NASA Langley Research Center during the formulation of requirements for research projects. The objective of Goals Analysis is to identify and explore all of the influencing factors that ultimately drive the system's requirements.

An Aircraft Separation Algorithm with Feedback and Perturbation

NASA Technical Reports Server (NTRS)

White, Allan L.

2010-01-01

A separation algorithm is a set of rules that tell aircraft how to maneuver in order to maintain a minimum distance between them. This paper investigates demonstrating that separation algorithms satisfy the FAA requirement for the occurrence of incidents by means of simulation. Any demonstration that a separation algorithm, or any other aspect of flight, satisfies the FAA requirement is a challenge because of the stringent nature of the requirement and the complexity of airspace operations. The paper begins with a probability and statistical analysis of both the FAA requirement and demonstrating meeting it by a Monte Carlo approach. It considers the geometry of maintaining separation when one plane must change its flight path. It then develops a simple feedback control law that guides the planes on their paths. The presence of feedback control permits the introduction of perturbations, and the stochastic nature of the chosen perturbation is examined. The simulation program is described. This paper is an early effort in the realistic demonstration of a stringent requirement. Much remains to be done.

A multiple functional connector for high-resolution optical satellites

NASA Astrophysics Data System (ADS)

She, Fengke; Zheng, Gangtie

2017-11-01

For earth observation satellites, perturbations from actuators, such as CMGs and momentum wheels, and thermal loadings from support structures often have significant impact on the image quality of an optical. Therefore, vibration isolators and thermal deformation releasing devices nowadays often become important parts of an image satellite. However, all these devices will weak the connection stiffness between the optical instrument and the satellite bus structure. This will cause concern of the attitude control system design for worrying about possible negative effect on the attitude control. Therefore, a connection design satisfying all three requirements is a challenge of advanced image satellites. Chinese scientists have proposed a large aperture high-resolution satellite for earth observation. To meet all these requirements and ensure image quality, specified multiple function connectors are designed to meet these challenging requirements, which are: isolating vibration, releasing thermal deformation and ensuring whole satellite dynamic properties [1]. In this paper, a parallel spring guide flexure is developed for both vibration isolation and thermal deformation releasing. The stiffness of the flexure is designed to meet the vibration isolation requirement. To attenuate vibration, and more importantly to satisfy the stability requirement of the attitude control system, metal damping, which has many merits for space applications, are applied in this connecter to provide a high damping ratio and nonlinear stiffness. The capability of the connecter for vibration isolation and attenuation is validated through numerical simulation and experiments. Connecter parameter optimization is also conducted to meet both requirements of thermal deformation releasing and attitude control. Analysis results show that the in-orbit attitude control requirement is satisfied while the thermal releasing performance is optimized. The design methods and analysis results are also provided in the present paper.

Application of the generalized reduced gradient method to conceptual aircraft design

NASA Technical Reports Server (NTRS)

Gabriele, G. A.

1984-01-01

The complete aircraft design process can be broken into three phases of increasing depth: conceptual design, preliminary design, and detail design. Conceptual design consists primarily of developing general arrangements and selecting the configuration that optimally satisfies all mission requirements. The result of the conceptual phase is a conceptual baseline configuration that serves as the starting point for the preliminary design phase. The conceptual design of an aircraft involves a complex trade-off of many independent variables that must be investigated before deciding upon the basic configuration. Some of these variables are discrete (number of engines), some represent different configurations (canard vs conventional tail) and some may represent incorporation of new technologies (aluminum vs composite materials). At Lockheed-Georgia, the sizing program is known as GASP (Generalized Aircraft Sizing Program). GASP is a large program containing analysis modules covering the many different disciplines involved fin defining the aricraft, such as aerodynamics, structures, stability and control, mission performance, and cost. These analysis modules provide first-level estimates the aircraft properties that are derived from handbook, experimental, and historical sources.

Recent Progress in Active Antenna Designs for the Long Wavelength Array (LWA)

NASA Astrophysics Data System (ADS)

Hicks, B. C.; Stewart, K. P.; Paravastu, N.; Bradley, R. F.; Parashare, C. R.; Erickson, W. C.; Gross, C.; Polisensky, E.; Crane, P. C.; Ray, P. S.; Kassim, N. E.; Weiler, K. W.

2005-12-01

We present new designs for active antenna systems optimized for HF/VHF radio astronomy, ionospheric science, space weather, and other radio science applications. Active antenna designs have been developed and tested which satisfy the need for high linearity and stability while achieving Galactic background dominated noise levels. The presence of very strong terrestrial radio-frequency interference (RFI), and world-wide propagation at these frequencies require that the preamplifiers have very high dynamic range. Distortion products must be below the Galactic background level for RFI mitigation techniques to be successful. Individual antennas should have broad response patterns to cover most of the sky without pointing mechanisms, but with decreased sensitivity at low elevations. Ideal designs would also be immune to environmental effects such as temperature variations and precipitation. For projects such as the LWA, where thousands of receptors will be needed, they must also be robust, inexpensive, and easy to manufacture and install. We discuss high-performance designs that are optimized for cost-sensitive applications such as the LWA. Basic research in astronomy is supported by the Office of Naval Research.

[The supply chain is everybody's business...].

PubMed

Coulondre, Antoine

2007-05-01

The management of the supply chain is a matter of delicate balance. This is certainly due to its position at the crossroads between suppliers and users requirements, as well as logistic, financial and technical regulations. For a public organisation like EFS, whose annual budget amounts to 697 million euros, there is a lot at stake: supplies represent the second most important item of its budget accounting for 38% of annual expenses. Three quarters of the purchases concern basic activities such as blood collection, testing procedures, transformation and distribution of blood products. The last quarter is spent on more general activities (computer systems, telecommunications...). Professionalisation of the purchasing function has grown since the creation of the government-owned organisation as a single national unit (EFS) in the year 2000. Its consequences can be felt especially in the field of the "core activities". The current stage consists in maintaining close links between all the skills necessary to a high-quality supply chain. The latter will undoubtedly be beneficial to the medical, technical and support departments of EFS, which are the in-house customers to satisfy.

Development and applications of 3-dimensional integration nanotechnologies.

PubMed

Kim, Areum; Choi, Eunmi; Son, Hyungbin; Pyo, Sung Gyu

2014-02-01

Unlike conventional two-dimensional (2D) planar structures, signal or power is supplied through through-silicon via (TSV) in three-dimensional (3D) integration technology to replace wires for binding the chip/wafer. TSVs have becomes an essential technology, as they satisfy Moore's law. This 3D integration technology enables system and sensor functions at a nanoscale via the implementation of a highly integrated nano-semiconductor as well as the fabrication of a single chip with multiple functions. Thus, this technology is considered to be a new area of development for the systemization of the nano-bio area. In this review paper, the basic technology required for such 3D integration is described and methods to measure the bonding strength in order to measure the void occurring during bonding are introduced. Currently, CMOS image sensors and memory chips associated with nanotechnology are being realized on the basis of 3D integration technology. In this paper, we intend to describe the applications of high-performance nano-biosensor technology currently under development and the direction of development of a high performance lab-on-a-chip (LOC).

Design and prototype tests of a seismic attenuation system for the advanced-LIGO output mode cleaner

NASA Astrophysics Data System (ADS)

Bertolini, A.; DeSalvo, R.; Galli, C.; Gennaro, G.; Mantovani, M.; Márka, S.; Sannibale, V.; Takamori, A.; Torrie, C.

2006-04-01

Both present LIGO and advanced LIGO (Ad-LIGO) will need an output mode cleaner (OMC) to reach the desired sensitivity. We designed a suitable OMC seismically attenuated optical table fitting to the existing vacuum chambers (horizontal access module, HAM chambers). The most straightforward and cost-effective solution satisfying the Ad-LIGO seismic attenuation specifications was to implement a single passive seismic attenuation stage, derived from the 'seismic attenuation system' (SAS) concept. We built and tested prototypes of all critical components. On the basis of these tests and past experience, we expect that the passive attenuation performance of this new design, called HAM-SAS, will match all requirements for the LIGO OMC, and all Ad-LIGO optical tables. Its performance can be improved, if necessary, by implementation of a simple active attenuation loop at marginal additional cost. The design can be easily modified to equip the LIGO basic symmetric chamber (BSC) chambers and leaves space for extensive performance upgrades for future evolutions of Ad-LIGO. Design parameters and prototype test results are presented.

Damage-mitigating control of aerospace systems for high performance and extended life

NASA Technical Reports Server (NTRS)

Ray, Asok; Wu, Min-Kuang; Carpino, Marc; Lorenzo, Carl F.; Merrill, Walter C.

1992-01-01

The concept of damage-mitigating control is to minimize fatigue (as well as creep and corrosion) damage of critical components of mechanical structures while simultaneously maximizing the system dynamic performance. Given a dynamic model of the plant and the specifications for performance and stability robustness, the task is to synthesize a control law that would meet the system requirements and, at the same time, satisfy the constraints that are imposed by the material and structural properties of the critical components. The authors present the concept of damage-mitigating control systems design with the following objectives: (1) to achieve high performance with a prolonged life span; and (2) to systematically update the controller as the new technology of advanced materials evolves. The major challenge is to extract the information from the material properties and then utilize this information in a mathematical form so that it can be directly applied to robust control synthesis for mechanical systems. The basic concept of damage-mitigating control is illustrated using a relatively simplified model of a space shuttle main engine.

A wireless multi-channel bioimpedance measurement system for personalized healthcare and lifestyle.

PubMed

Ramos, Javier; Ausín, José Luis; Lorido, Antonio Manuel; Redondo, Francisco; Duque-Carrillo, Juan Francisco

2013-01-01

Miniaturized, noninvasive, wearable sensors constitute a fundamental prerequisite for pervasive, predictive, and preventive healthcare systems. In this sense, this paper presents the design, realization, and evaluation of a wireless multi-channel measurement system based on a cost-effective high-performance integrated circuit for electrical bioimpedance (EBI) measurements in the frequency range from 1 kHz to 1 MHz. The resulting on-chip spectrometer provides high measuring EBI capabilities and together with a low-cost, commercially available radio frequency transceiver device. It provides reliable wireless communication, constitutes the basic node to build EBI wireless sensor networks (EBI-WSNs). The proposed EBI-WSN behaves as a high-performance wireless multi-channel EBI spectrometer, where the number of channels is completely scalable and independently configurable to satisfy specific measurement requirements of each individual. A prototype of the EBI node leads to a very small printed circuit board of approximately 8 cm2 including chip-antenna, which can operate several years on one 3-V coin cell battery and make it suitable for long-term preventive healthcare monitoring.

Small Form Factor Information Storage Devices for Mobile Applications in Korea

NASA Astrophysics Data System (ADS)

Park, Young-Pil; Park, No-Cheol; Kim, Chul-Jin

Recently, the ubiquitous environment in which anybody can reach a lot of information data without any limitations on the place and time has become an important social issue. There are two basic requirements in the field of information storage devices which have to be satisfied; the first is the demand for the improvement of memory capacity to manage the increased data capacity in personal and official purposes. The second is the demand for new development of information storage devices small enough to be applied to mobile multimedia digital electronics, including digital camera, PDA and mobile phones. To summarize, for the sake of mobile applications, it is necessary to develop information storage devices which have simultaneously a large capacity and a small size. Korea possesses the necessary infrastructure for developing such small sized information storage devices. It has a good digital market, major digital companies, and various research institutes. Nowadays, many companies and research institutes including university cooperate together in the research on small sized information storage devices. Thus, it is expected that small form factor optical disk drives will be commercialized in the very near future in Korea.

The Profiles in Science Digital Library: Behind the Scenes.

PubMed

Gallagher, Marie E; Moffatt, Christie

2012-01-01

This demonstration shows the Profiles in Science ® digital library. Profiles in Science contains digitized selections from the personal manuscript collections of prominent biomedical researchers, medical practitioners, and those fostering science and health. The Profiles in Science Web site is the delivery mechanism for content derived from the digital library system. The system is designed according to our basic principles for digital library development [1]. The digital library includes the rules and software used for digitizing items, creating and editing database records and performing quality control as well as serving the digital content to the public. Among the types of data managed by the digital library are detailed item-level, collection-level and cross-collection metadata, digitized photographs, papers, audio clips, movies, born-digital electronic files, optical character recognized (OCR) text, and annotations (see Figure 1). The digital library also tracks the status of each item, including digitization quality, sensitivity of content, and copyright. Only items satisfying all required criteria are released to the public through the World Wide Web. External factors have influenced all aspects of the digital library's infrastructure.

Application of an imaging system to a museum exhibition for developing interactive exhibitions

NASA Astrophysics Data System (ADS)

Miyata, Kimiyoshi; Inoue, Yuka; Takiguchi, Takahiro; Tsumura, Norimichi; Nakaguchi, Toshiya; Miyake, Yoichi

2009-10-01

In the National Museum of Japanese History, 215,759 artifacts are stored and used for research and exhibitions. In museums, due to the limitation of space in the galleries, a guidance system is required to satisfy visitors' needs and to enhance their understanding of the artifacts. We introduce one exhibition using imaging technology to improve visitors' understanding of a kimono (traditional Japanese clothing) exhibition. In the imaging technology introduced, one data projector, one display with touch panel interface, and magnifiers were used as exhibition tools together with a real kimono. The validity of this exhibition method was confirmed by results from a visitors' interview survey. Second, to further develop the interactive guidance system, an augmented reality system that consisted of cooperation between the projector and a digital video camera was also examined. A white paper board in the observer's hand was used as a projection screen and also as an interface to control the images projected on the board. The basic performance of the proposed system was confirmed; however continuous development was necessary for applying the system to actual exhibitions.

Prospects for development of hydrocarbon raw materials resources reproduction

NASA Astrophysics Data System (ADS)

Vertakova, Y. V.; Babich, T. N.; Polozhentseva, Y. S.; Zvyagintsev, G. L.

2017-10-01

The article presents data on the influence of factors in the field of innovative technology of thermocatalytic depolymerization of solid household wastes (SHW) on the efficiency and prospects for the development of technogenic hydrocarbon raw materials resource reproduction. Process thermodynamics, reactions kinetics, the mechanism of thermolysis of secondary polymers in organic solvents have been studied by means of laboratory experiments. It is shown that different morphological groups of wastes dissolve practically at the same rate at temperatures of 250-310°C. A homogeneous product is formed in the liquid phase; the spread of values for the elements lies in the interval of 1.5-4.5 %; technological requirements of the stages of formation of boiler fuels are satisfied. Using the principles of patent analysis, new techniques of processing household waste components are proposed. The basics of energy-efficient and energy-saving processes of technogenic hydrocarbon raw materials resource reproduction have been laid. The possibility of increasing the production payback and intensification is shown. Ecological and demographic safety for population and technical and economic benefits from SHW processing are achieved.

On a viable first-order formulation of relativistic viscous fluids and its applications to cosmology

NASA Astrophysics Data System (ADS)

Disconzi, Marcelo M.; Kephart, Thomas W.; Scherrer, Robert J.

We consider a first-order formulation of relativistic fluids with bulk viscosity based on a stress-energy tensor introduced by Lichnerowicz. Choosing a barotropic equation-of-state, we show that this theory satisfies basic physical requirements and, under the further assumption of vanishing vorticity, that the equations of motion are causal, both in the case of a fixed background and when the equations are coupled to Einstein's equations. Furthermore, Lichnerowicz's proposal does not fit into the general framework of first-order theories studied by Hiscock and Lindblom, and hence their instability results do not apply. These conclusions apply to the full-fledged nonlinear theory, without any equilibrium or near equilibrium assumptions. Similarities and differences between the approach explored here and other theories of relativistic viscosity, including the Mueller-Israel-Stewart formulation, are addressed. Cosmological models based on the Lichnerowicz stress-energy tensor are studied. As the topic of (relativistic) viscous fluids is also of interest outside the general relativity and cosmology communities, such as, for instance, in applications involving heavy-ion collisions, we make our presentation largely self-contained.

48 CFR 801.602-71 - Basic review requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 48 Federal Acquisition Regulations System 5 2010-10-01 2010-10-01 false Basic review requirements... GENERAL DEPARTMENT OF VETERANS AFFAIRS ACQUISITION REGULATION SYSTEM Career Development, Contracting Authority, and Responsibilities 801.602-71 Basic review requirements. Contracting officers must obtain...

Hypergeometric Equation in Modeling Relativistic Isotropic Sphere

NASA Astrophysics Data System (ADS)

Thirukkanesh, S.; Ragel, F. C.

2014-04-01

We study the Einstein system of equations in static spherically symmetric spacetimes. We obtained classes of exact solutions to the Einstein system by transforming the condition for pressure isotropy to a hypergeometric equation choosing a rational form for one of the gravitational potentials. The solutions are given in simple form that is a desirable requisite to study the behavior of relativistic compact objects in detail. A physical analysis indicate that our models satisfy all the fundamental requirements of realistic star and match smoothly with the exterior Schwarzschild metric. The derived masses and densities are consistent with the previously reported experimental and theoretical studies describing strange stars. The models satisfy the standard energy conditions required by normal matter.

Survey of needs and capabilities for wind tunnel testing of dynamic stability of aircraft at high angles of attack

NASA Technical Reports Server (NTRS)

Orlik-Ruckemann, K. J.

1973-01-01

A survey was conducted relative to future requirements for dynamic stability information for such aerospace vehicles as the space shuttle and advanced high performance military aircraft. High-angle-of-attack and high-Reynolds number conditions were emphasized. A review was made of the wind-tunnel capabilities in North America for measuring dynamic stability derivatives, revealing an almost total lack of capabilities that could satisfy these requirements. Recommendations are made regarding equipment that should be constructed to remedy this situation. A description is given of some of the more advanced existing capabilities, which can be used to at least partly satisfy immediate demands.

48 CFR 926.7002 - Responsibilities.

Code of Federal Regulations, 2014 CFR

2014-10-01

... SOCIOECONOMIC PROGRAMS Implementation of Section 3021 of the Energy Policy Act of 1992 926.7002 Responsibilities... requirements falling within the scope of section 3021 of the Energy Policy Act. Identification shall occur at... award that directly satisfies an Energy Policy Act program or requirement. ...

48 CFR 926.7002 - Responsibilities.

Code of Federal Regulations, 2012 CFR

2012-10-01

... SOCIOECONOMIC PROGRAMS Implementation of Section 3021 of the Energy Policy Act of 1992 926.7002 Responsibilities... requirements falling within the scope of section 3021 of the Energy Policy Act. Identification shall occur at... award that directly satisfies an Energy Policy Act program or requirement. ...

48 CFR 926.7002 - Responsibilities.

Code of Federal Regulations, 2013 CFR

2013-10-01

... SOCIOECONOMIC PROGRAMS Implementation of Section 3021 of the Energy Policy Act of 1992 926.7002 Responsibilities... requirements falling within the scope of section 3021 of the Energy Policy Act. Identification shall occur at... award that directly satisfies an Energy Policy Act program or requirement. ...

48 CFR 926.7002 - Responsibilities.

Code of Federal Regulations, 2011 CFR

2011-10-01

... SOCIOECONOMIC PROGRAMS Implementation of Section 3021 of the Energy Policy Act of 1992 926.7002 Responsibilities... requirements falling within the scope of section 3021 of the Energy Policy Act. Identification shall occur at... award that directly satisfies an Energy Policy Act program or requirement. ...

48 CFR 926.7002 - Responsibilities.

Code of Federal Regulations, 2010 CFR

2010-10-01

... SOCIOECONOMIC PROGRAMS Implementation of Section 3021 of the Energy Policy Act of 1992 926.7002 Responsibilities... requirements falling within the scope of section 3021 of the Energy Policy Act. Identification shall occur at... award that directly satisfies an Energy Policy Act program or requirement. ...

Galileo environmental test and analysis program summary

NASA Technical Reports Server (NTRS)

Hoffman, A. R.

1991-01-01

This paper presents an overview of the Galileo Project's environmental test and analysis program during the spacecraft development phase - October 1978 through launch in October 1989. After describing the top-level objectives of the program, summaries of-the approach, requirements, and margins are provided. Examples of assembly- and system-level test results are given for both the pre-1986 (direct mission) testing and the post-1986 (Venus-Earth-Earth gravity assist mission) testing, including dynamic, thermal, electromagnetic compatibility (EMC), and magnetic. The approaches and results for verifying by analysis that the requirements of certain environments (e.g., radiation, micrometeoroids, and single event upsets) are satisfied are presented. The environmental program implemented on Galileo satisfied the spirit and intent of the requirements imposed by the Project during the spacecraft's development. The lessons learned from the Galileo environmental program are discussed in this paper.

Requirements for Simulating Space Radiation With Particle Accelerators

NASA Technical Reports Server (NTRS)

Schimmerling, W.; Wilson, J. W.; Cucinotta, F.; Kim, M-H Y.

2004-01-01

Interplanetary space radiation consists of fully ionized nuclei of atomic elements with high energy for which only the few lowest energy ions can be stopped in shielding materials. The health risk from exposure to these ions and their secondary radiations generated in the materials of spacecraft and planetary surface enclosures is a major limiting factor in the management of space radiation risk. Accurate risk prediction depends on a knowledge of basic radiobiological mechanisms and how they are modified in the living tissues of a whole organism. To a large extent, this knowledge is not currently available. It is best developed at ground-based laboratories, using particle accelerator beams to simulate the components of space radiation. Different particles, in different energy regions, are required to study different biological effects, including beams of argon and iron nuclei in the energy range 600 to several thousand MeV/nucleon and carbon beams in the energy range of approximately 100 MeV/nucleon to approximately 1000 MeV/nucleon. Three facilities, one each in the United States, in Germany and in Japan, currently have the partial capability to satisfy these constraints. A facility has been proposed using the Brookhaven National Laboratory Booster Synchrotron in the United States; in conjunction with other on-site accelerators, it will be able to provide the full range of heavy ion beams and energies required. International cooperation in the use of these facilities is essential to the development of a safe international space program.

Making Games Not Work: Paradoxes Embedded in Game-Based Training and Concepts for Overcoming Them

NASA Technical Reports Server (NTRS)

Jones, Phillip N.; Cuper, Taryn

2010-01-01

An interest in game-based training solutions is natural. All one has to do is watch someone fully engaged in a modern game to see the potential of harnessing that attention for training. However, the reality of game-based training has not fully satisfied these expectations. This paper explains two paradoxes that must be overcome for games to support training. These paradoxes are a result of the realities of the basic human condition clashing with the requirements of learning theory. 80th paradoxes arise from the concept of "engagement" that is central to games. The first comes from a more robust definition of engagement, which is the condition of Flow or Optimal Experience. Flow is the state game developers want to see in users. One aspect of Flow is loss of sense of self as the individual becomes immersed in the experience. The paradox arises because this loss of self directly contradicts the learning requirement of self-reflection. The second paradox comes from theories of play, which state in part that play requires a level of individual freedom. The contradiction arises when game-based play must be harnessed to an organizational training program or regimen. The paper will discuss these paradoxes in the context of an effort to design a game-based training modality to train combat medics and will close with a review of compensating strategies identified by the designers. The paper will provide information important to anyone interested in conceptualizing and designing game-based training.

Forward collision warning based on kernelized correlation filters

NASA Astrophysics Data System (ADS)

Pu, Jinchuan; Liu, Jun; Zhao, Yong

2017-07-01

A vehicle detection and tracking system is one of the indispensable methods to reduce the occurrence of traffic accidents. The nearest vehicle is the most likely to cause harm to us. So, this paper will do more research on about the nearest vehicle in the region of interest (ROI). For this system, high accuracy, real-time and intelligence are the basic requirement. In this paper, we set up a system that combines the advanced KCF tracking algorithm with the HaarAdaBoost detection algorithm. The KCF algorithm reduces computation time and increase the speed through the cyclic shift and diagonalization. This algorithm satisfies the real-time requirement. At the same time, Haar features also have the same advantage of simple operation and high speed for detection. The combination of this two algorithm contribute to an obvious improvement of the system running rate comparing with previous works. The detection result of the HaarAdaBoost classifier provides the initial value for the KCF algorithm. This fact optimizes KCF algorithm flaws that manual car marking in the initial phase, which is more scientific and more intelligent. Haar detection and KCF tracking with Histogram of Oriented Gradient (HOG) ensures the accuracy of the system. We evaluate the performance of framework on dataset that were self-collected. The experimental results demonstrate that the proposed method is robust and real-time. The algorithm can effectively adapt to illumination variation, even in the night it can meet the detection and tracking requirements, which is an improvement compared with the previous work.

Awareness-based game-theoretic space resource management

NASA Astrophysics Data System (ADS)

Chen, Genshe; Chen, Huimin; Pham, Khanh; Blasch, Erik; Cruz, Jose B., Jr.

2009-05-01

Over recent decades, the space environment becomes more complex with a significant increase in space debris and a greater density of spacecraft, which poses great difficulties to efficient and reliable space operations. In this paper we present a Hierarchical Sensor Management (HSM) method to space operations by (a) accommodating awareness modeling and updating and (b) collaborative search and tracking space objects. The basic approach is described as follows. Firstly, partition the relevant region of interest into district cells. Second, initialize and model the dynamics of each cell with awareness and object covariance according to prior information. Secondly, explicitly assign sensing resources to objects with user specified requirements. Note that when an object has intelligent response to the sensing event, the sensor assigned to observe an intelligent object may switch from time-to-time between a strong, active signal mode and a passive mode to maximize the total amount of information to be obtained over a multi-step time horizon and avoid risks. Thirdly, if all explicitly specified requirements are satisfied and there are still more sensing resources available, we assign the additional sensing resources to objects without explicitly specified requirements via an information based approach. Finally, sensor scheduling is applied to each sensor-object or sensor-cell pair according to the object type. We demonstrate our method with realistic space resources management scenario using NASA's General Mission Analysis Tool (GMAT) for space object search and track with multiple space borne observers.

24 CFR 599.203 - Basic application submission requirements.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 24 Housing and Urban Development 3 2010-04-01 2010-04-01 false Basic application submission... Development (Continued) OFFICE OF ASSISTANT SECRETARY FOR COMMUNITY PLANNING AND DEVELOPMENT, DEPARTMENT OF... Renewal Communities § 599.203 Basic application submission requirements. The basic application submission...

33 CFR 154.2201 - Vapor control system-general requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

... high liquid level sensor that activates an alarm that satisfies the requirements of 33 CFR 154.2100(e); and (3) A high-high liquid level sensor that closes the remotely operated cargo vapor shutoff valve... vapor-moving device. One sensor with two stages may be used to meet this requirement as well as...

26 CFR 1.410(b)-1 - Minimum coverage requirements (before 1994).

Code of Federal Regulations, 2011 CFR

2011-04-01

... (CONTINUED) INCOME TAX (CONTINUED) INCOME TAXES (CONTINUED) Pension, Profit-Sharing, Stock Bonus Plans, Etc... the minimum age and service requirements (if any) prescribed by the plan, as of the date coverage is... employees (including employees who do not satisfy the minimum age or service requirements of the plan) are...

77 FR 13678 - Self-Regulatory Organizations; ICE Clear Credit LLC; Notice of Filing of Proposed Rule To Provide...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-07

...%) of the Initial Margin Requirement for Client-related Positions Cleared in a Clearing Participant's... satisfy the initial margin-related liquidity requirements for client-related positions cleared in a... hundred percent (100%) of the initial margin requirement for client-related positions cleared in a...

26 CFR 1.401(k)-4 - SIMPLE 401(k) plan requirements.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 26 Internal Revenue 5 2012-04-01 2011-04-01 true SIMPLE 401(k) plan requirements. 1.401(k)-4 Section 1.401(k)-4 Internal Revenue INTERNAL REVENUE SERVICE, DEPARTMENT OF THE TREASURY (CONTINUED...(k)-4 SIMPLE 401(k) plan requirements. (a) General rule. A cash or deferred arrangement satisfies the...

26 CFR 1.401(k)-4 - SIMPLE 401(k) plan requirements.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 26 Internal Revenue 5 2014-04-01 2014-04-01 false SIMPLE 401(k) plan requirements. 1.401(k)-4 Section 1.401(k)-4 Internal Revenue INTERNAL REVENUE SERVICE, DEPARTMENT OF THE TREASURY (CONTINUED...(k)-4 SIMPLE 401(k) plan requirements. (a) General rule. A cash or deferred arrangement satisfies the...

26 CFR 1.401(k)-4 - SIMPLE 401(k) plan requirements.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 26 Internal Revenue 5 2011-04-01 2011-04-01 false SIMPLE 401(k) plan requirements. 1.401(k)-4 Section 1.401(k)-4 Internal Revenue INTERNAL REVENUE SERVICE, DEPARTMENT OF THE TREASURY (CONTINUED...(k)-4 SIMPLE 401(k) plan requirements. (a) General rule. A cash or deferred arrangement satisfies the...

26 CFR 1.401(k)-4 - SIMPLE 401(k) plan requirements.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 26 Internal Revenue 5 2013-04-01 2013-04-01 false SIMPLE 401(k) plan requirements. 1.401(k)-4 Section 1.401(k)-4 Internal Revenue INTERNAL REVENUE SERVICE, DEPARTMENT OF THE TREASURY (CONTINUED...(k)-4 SIMPLE 401(k) plan requirements. (a) General rule. A cash or deferred arrangement satisfies the...

42 CFR 84.103 - Man tests; performance requirements.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 42 Public Health 1 2013-10-01 2013-10-01 false Man tests; performance requirements. 84.103 Section...-Contained Breathing Apparatus § 84.103 Man tests; performance requirements. (a) The apparatus shall satisfy... is 24 ±6 °C. (75 ±10 °F.), the maximum temperature of inspired air recorded during man tests shall...

42 CFR 84.103 - Man tests; performance requirements.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 42 Public Health 1 2014-10-01 2014-10-01 false Man tests; performance requirements. 84.103 Section...-Contained Breathing Apparatus § 84.103 Man tests; performance requirements. (a) The apparatus shall satisfy... is 24 ±6 °C. (75 ±10 °F.), the maximum temperature of inspired air recorded during man tests shall...

42 CFR 84.103 - Man tests; performance requirements.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 42 Public Health 1 2012-10-01 2012-10-01 false Man tests; performance requirements. 84.103 Section...-Contained Breathing Apparatus § 84.103 Man tests; performance requirements. (a) The apparatus shall satisfy... is 24 ±6 °C. (75 ±10 °F.), the maximum temperature of inspired air recorded during man tests shall...

7 CFR 1717.306 - RUS required rates.

Code of Federal Regulations, 2011 CFR

2011-01-01

...-emption in Rate Making in Connection With Power Supply Borrowers § 1717.306 RUS required rates. (a) Upon... of RUS that are sufficient to satisfy the requirements of the RUS wholesale power contract and other... with terms of the RUS wholesale power contract and other RUS documents in a timely fashion, RUS may...

7 CFR 1717.306 - RUS required rates.

Code of Federal Regulations, 2010 CFR

2010-01-01

...-emption in Rate Making in Connection With Power Supply Borrowers § 1717.306 RUS required rates. (a) Upon... of RUS that are sufficient to satisfy the requirements of the RUS wholesale power contract and other... with terms of the RUS wholesale power contract and other RUS documents in a timely fashion, RUS may...

78 FR 49681 - Requirement of a Section 4959 Excise Tax Return and Time for Filing the Return

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-15

... failure to meet the community health needs assessment (CHNA) requirements for any taxable year. The... organizations to satisfy the community health needs assessment requirements of section 501(r)(3). A hospital... three years and adopt an implementation strategy to meet the community health needs identified through...

49 CFR 383.123 - Requirements for a school bus endorsement.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 5 2011-10-01 2011-10-01 false Requirements for a school bus endorsement. 383.123... Requirements for a school bus endorsement. (a) An applicant for the school bus endorsement must satisfy the... for school buses by State or Federal law or regulation. (ii) Emergency exits and procedures for safely...

Requirements controlled design: A method for discovery of discontinuous system boundaries in the requirements hyperspace

NASA Astrophysics Data System (ADS)

Hollingsworth, Peter Michael

The drive toward robust systems design, especially with respect to system affordability throughout the system life-cycle, has led to the development of several advanced design methods. While these methods have been extremely successful in satisfying the needs for which they have been developed, they inherently leave a critical area unaddressed. None of them fully considers the effect of requirements on the selection of solution systems. The goal of all of current modern design methodologies is to bring knowledge forward in the design process to the regions where more design freedom is available and design changes cost less. Therefore, it seems reasonable to consider the point in the design process where the greatest restrictions are placed on the final design, the point in which the system level requirements are set. Historically the requirements have been treated as something handed down from above. However, neither the customer nor the solution provider completely understood all of the options that are available in the broader requirements space. If a method were developed that provided the ability to understand the full scope of the requirements space, it would allow for a better comparison of potential solution systems with respect to both the current and potential future requirements. The key to a requirements conscious method is to treat requirements differently from the traditional approach. The method proposed herein is known as Requirements Controlled Design (RCD). By treating the requirements as a set of variables that control the behavior of the system, instead of variables that only define the response of the system, it is possible to determine a-priori what portions of the requirements space that any given system is capable of satisfying. Additionally, it should be possible to identify which systems can satisfy a given set of requirements and the locations where a small change in one or more requirements poses a significant risk to a design program. This thesis puts forth the theory and methodology to enable RCD, and details and validates a specific method called the Modified Strength Pareto Evolutionary Algorithm (MSPEA).

Entanglement of purification through holographic duality

NASA Astrophysics Data System (ADS)

Umemoto, Koji; Takayanagi, Tadashi

2018-06-01

The gauge/gravity correspondence discovered two decades ago has had a profound influence on how the basic laws in physics should be formulated. In spite of the predictive power of holographic approaches (for example, when they are applied to strongly coupled condensed-matter physics problems), the fundamental reasons behind their success remain unclear. Recently, the role of quantum entanglement has come to the fore. Here we explore a quantity that connects gravity and quantum information in the light of the gauge/gravity correspondence. This is given by the minimal cross-section of the entanglement wedge that connects two disjoint subsystems in a gravity dual. In particular, we focus on various inequalities that are satisfied by this quantity. They suggest that it is a holographic counterpart of the quantity called entanglement of purification, which measures a bipartite correlation in a given mixed state. We give a heuristic argument that supports this identification based on a tensor network interpretation of holography. This predicts that the entanglement of purification satisfies the strong superadditivity for holographic conformal field theories.

Electrochemistry and Storage Panel Report

NASA Technical Reports Server (NTRS)

Stedman, J. K.; Halpert, G.

1984-01-01

Design and performance requirements for electrochemical power storage systems are discussed and some of the approaches towards satisfying these constraints are described. Geosynchronous and low Earth orbit applications, radar type load constraints, and high voltage systems requirements are addressed. In addition, flywheel energy storage is discussed.

45 CFR 263.8 - What happens if a State fails to meet the basic MOE requirement?

Code of Federal Regulations, 2010 CFR

2010-10-01

... 45 Public Welfare 2 2010-10-01 2010-10-01 false What happens if a State fails to meet the basic... Maintenance of Effort? § 263.8 What happens if a State fails to meet the basic MOE requirement? (a) If any State fails to meet its basic MOE requirement for any fiscal year, then we will reduce dollar-for-dollar...

5 CFR 300.103 - Basic requirements.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 5 Administrative Personnel 1 2010-01-01 2010-01-01 false Basic requirements. 300.103 Section 300.103 Administrative Personnel OFFICE OF PERSONNEL MANAGEMENT CIVIL SERVICE REGULATIONS EMPLOYMENT (GENERAL) Employment Practices § 300.103 Basic requirements. (a) Job analysis. Each employment practice of the Federal Government generally, and of...

Additively manufactured biodegradable porous magnesium.

PubMed

Li, Y; Zhou, J; Pavanram, P; Leeflang, M A; Fockaert, L I; Pouran, B; Tümer, N; Schröder, K-U; Mol, J M C; Weinans, H; Jahr, H; Zadpoor, A A

2018-02-01

An ideal bone substituting material should be bone-mimicking in terms of mechanical properties, present a precisely controlled and fully interconnected porous structure, and degrade in the human body to allow for full regeneration of large bony defects. However, simultaneously satisfying all these three requirements has so far been highly challenging. Here we present topologically ordered porous magnesium (WE43) scaffolds based on the diamond unit cell that were fabricated by selective laser melting (SLM) and satisfy all the requirements. We studied the in vitro biodegradation behavior (up to 4 weeks), mechanical properties and biocompatibility of the developed scaffolds. The mechanical properties of the AM porous WE43 (E = 700-800 MPa) scaffolds were found to fall into the range of the values reported for trabecular bone even after 4 weeks of biodegradation. Scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), electrochemical tests and µCT revealed a unique biodegradation mechanism that started with uniform corrosion, followed by localized corrosion, particularly in the center of the scaffolds. Biocompatibility tests performed up to 72 h showed level 0 cytotoxicity (according to ISO 10993-5 and -12), except for one time point (i.e., 24 h). Intimate contact between cells (MG-63) and the scaffolds was also observed in SEM images. The study shows for the first time that AM of porous Mg may provide distinct possibilities to adjust biodegradation profile through topological design and open up unprecedented opportunities to develop multifunctional bone substituting materials that mimic bone properties and enable full regeneration of critical-size load-bearing bony defects. The ideal biomaterials for bone tissue regeneration should be bone-mimicking in terms of mechanical properties, present a fully interconnected porous structure, and exhibit a specific biodegradation behavior to enable full regeneration of bony defects. Recent advances in additive manufacturing have resulted in biomaterials that satisfy the first two requirements but simultaneously satisfying the third requirement has proven challenging so far. Here we present additively manufactured porous magnesium structures that have the potential to satisfy all above-mentioned requirements. Even after 4 weeks of biodegradation, the mechanical properties of the porous structures were found to be within those reported for native bone. Moreover, our comprehensive electrochemical, mechanical, topological, and biological study revealed a unique biodegradation behavior and the limited cytotoxicity of the developed biomaterials. Copyright © 2017 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Pulse Jet Mixing Tests With Noncohesive Solids

DOE Office of Scientific and Technical Information (OSTI.GOV)

Meyer, Perry A.; Bamberger, Judith A.; Enderlin, Carl W.

2009-05-11

This report summarizes results from pulse jet mixing (PJM) tests with noncohesive solids in Newtonian liquid conducted during FY 2007 and 2008 to support the design of mixing systems for the Hanford Waste Treatment and Immobilization Plant (WTP). Tests were conducted at three geometric scales using noncohesive simulants. The test data were used to independently develop mixing models that can be used to predict full-scale WTP vessel performance and to rate current WTP mixing system designs against two specific performance requirements. One requirement is to ensure that all solids have been disturbed during the mixing action, which is important tomore » release gas from the solids. The second requirement is to maintain a suspended solids concentration below 20 weight percent at the pump inlet. The models predict the height to which solids will be lifted by the PJM action, and the minimum velocity needed to ensure all solids have been lifted from the floor. From the cloud height estimate we can calculate the concentration of solids at the pump inlet. The velocity needed to lift the solids is slightly more demanding than "disturbing" the solids, and is used as a surrogate for this metric. We applied the models to assess WTP mixing vessel performance with respect to the two perform¬ance requirements. Each mixing vessel was evaluated against these two criteria for two defined waste conditions. One of the wastes was defined by design limits and one was derived from Hanford waste characterization reports. The assessment predicts that three vessel types will satisfy the design criteria for all conditions evaluated. Seven vessel types will not satisfy the performance criteria used for any of the conditions evaluated. The remaining three vessel types provide varying assessments when the different particle characteristics are evaluated. The assessment predicts that three vessel types will satisfy the design criteria for all conditions evaluated. Seven vessel types will not satisfy the performance criteria used for any of the conditions evaluated. The remaining three vessel types provide varying assessments when the different particle characteristics are evaluated. The HLP-022 vessel was also evaluated using 12 m/s pulse jet velocity with 6-in. nozzles, and this design also did not satisfy the criteria for all of the conditions evaluated.« less

Diffusion Processes Satisfying a Conservation Law Constraint

DOE PAGES

Bakosi, J.; Ristorcelli, J. R.

2014-03-04

We investigate coupled stochastic differential equations governing N non-negative continuous random variables that satisfy a conservation principle. In various fields a conservation law requires that a set of fluctuating variables be non-negative and (if appropriately normalized) sum to one. As a result, any stochastic differential equation model to be realizable must not produce events outside of the allowed sample space. We develop a set of constraints on the drift and diffusion terms of such stochastic models to ensure that both the non-negativity and the unit-sum conservation law constraint are satisfied as the variables evolve in time. We investigate the consequencesmore » of the developed constraints on the Fokker-Planck equation, the associated system of stochastic differential equations, and the evolution equations of the first four moments of the probability density function. We show that random variables, satisfying a conservation law constraint, represented by stochastic diffusion processes, must have diffusion terms that are coupled and nonlinear. The set of constraints developed enables the development of statistical representations of fluctuating variables satisfying a conservation law. We exemplify the results with the bivariate beta process and the multivariate Wright-Fisher, Dirichlet, and Lochner’s generalized Dirichlet processes.« less

Diffusion Processes Satisfying a Conservation Law Constraint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bakosi, J.; Ristorcelli, J. R.

We investigate coupled stochastic differential equations governing N non-negative continuous random variables that satisfy a conservation principle. In various fields a conservation law requires that a set of fluctuating variables be non-negative and (if appropriately normalized) sum to one. As a result, any stochastic differential equation model to be realizable must not produce events outside of the allowed sample space. We develop a set of constraints on the drift and diffusion terms of such stochastic models to ensure that both the non-negativity and the unit-sum conservation law constraint are satisfied as the variables evolve in time. We investigate the consequencesmore » of the developed constraints on the Fokker-Planck equation, the associated system of stochastic differential equations, and the evolution equations of the first four moments of the probability density function. We show that random variables, satisfying a conservation law constraint, represented by stochastic diffusion processes, must have diffusion terms that are coupled and nonlinear. The set of constraints developed enables the development of statistical representations of fluctuating variables satisfying a conservation law. We exemplify the results with the bivariate beta process and the multivariate Wright-Fisher, Dirichlet, and Lochner’s generalized Dirichlet processes.« less

Evaluation of Clinical Reasoning in Basic Emergencies Using a Script Concordance Test

PubMed Central

Charlin, Bernard; Vanpee, Dominique

2010-01-01

Objectives To develop and assess the reliability of a script concordance test (SCT) to evaluate pharmacy students' clinical reasoning when facing basic emergency situations. Design A first aid course was designed that consisted of 8 weekly instructional sessions (4 on internal medicine, including life threatening situations; 2 on pediatrics; and 2 on trauma) in which the instructor presented case studies in a small-group format. In the first and final sessions of the course, a practice SCT was administered to familiarize students with the test format. Assessment A 66-question SCT examination was administered to the 68 third-year pharmacy students enrolled in the first aid course. The students' mean score was 68.5% ± 9.8% and panel members' mean score was 86.5% ± 4.2%. Twenty students were selected randomly to complete a course survey and 85% indicated they were satisfied with using the SCT. Conclusions A first aid SCT was found to be both a practical and reliable testing instrument for assessing the clinical reasoning of pharmacy students in basic emergency situations. PMID:21436943

A Study on the Optimal Generation Mix Based on Portfolio Theory with Considering the Basic Condition for Power Supply

NASA Astrophysics Data System (ADS)

Kato, Moritoshi; Zhou, Yicheng

This paper presents a novel method to analyze the optimal generation mix based on portfolio theory with considering the basic condition for power supply, which means that electricity generation corresponds with load curve. The optimization of portfolio is integrated with the calculation of a capacity factor of each generation in order to satisfy the basic condition for power supply. Besides, each generation is considered to be an asset, and risks of the generation asset both in its operation period and construction period are considered. Environmental measures are evaluated through restriction of CO2 emissions, which are indicated by CO2 price. Numerical examples show the optimal generation mix according to risks such as the deviation of capacity factor of nuclear power or restriction of CO2 emissions, the possibility of introduction of clean coal technology (IGCC, CCS) or renewable energy, and so on. The results of this work will be possibly applied as setting the target of the generation mix for the future according to prospects of risks of each generation and restrictions of CO2 emissions.

Determinants of village doctors' job satisfaction under China's health sector reform: a cross-sectional mixed methods study.

PubMed

Li, Tongtong; Lei, Trudy; Sun, Fiona; Xie, Zheng

2017-04-18

To strengthen rural health workforce, the Chinese government has launched a series of policies to promote the job satisfaction of village doctors since the health sector reform. The purpose of this mixed-method study is to describe village doctors' job satisfaction under the context of health sector reform and investigate the associated factors. Data was obtained from a survey of village doctors across three Chinese provinces in 2014. Using a multistage sampling process, quantitative data was collected from village doctors through the self-administered questionnaire and analyzed by multilevel logistic regression models. Qualitative data was collected through face-to-face semi-structured interviews on both village doctors and health managers. Theoretical coding was then conducted to analyze qualitative data. Among the 1221 respondents, 48.6% felt satisfied with their job. Older village doctors with less of a workload and under high-level integrated management were more likely to feel satisfied with their job. Village doctors who earned the top level of monthly income felt more satisfied, while on the county level, those who lived in counties with the highest GDP felt less satisfied. However, enrollment in a pension plan showed no significant difference in regards to village doctors' job satisfaction. Among 34 participants of qualitative interviews, most believed that age, income, and integrated management had a positive influence on the job satisfaction, while pension plan and basic public health care policies exhibited negative effects. Also, the increasing in availability of healthcare and health resources along with local economic development had negative effects on village doctors' job satisfaction. Village doctors' job satisfaction was quite low in regards to several determinants including age, income, workload, enrollment in a pension plan, integrated management, and county economic and medical availability development.

Oriental nose elongation using an L-shaped polyethylene sheet implant for combined septal spreading and extension.

PubMed

Zhou, Jia; Huang, Xiaolu; Zheng, Danning; Li, Haizhou; Herrler, Tanja; Li, Qingfeng

2014-04-01

The currently recommended strategies for short nose elongation were designed primarily for the Caucasian nasal framework. For Oriental patients, more elongation often is required because a hypoplastic septal cartilage requires more elongation, resulting in a higher risk of complications. This report proposes a modified technique for Oriental nose elongation, which adjusts the pressure points after nasal elongation using an L-shaped implant. Between January 2007 and December 2009, 58 patients underwent Oriental nose elongation using an L-shaped, porous, high-density polyethylene sheet implant. Augmentation rhinoplasty and conchal cartilage shield grafts were performed depending on the nasal shape. Pre- and postoperative nasal length, height, and projection as well as columella-labial angle, columella-lobular angle, and nasal tip angle were measured and compared. A patient satisfaction survey was performed postoperatively. All occurring complications were recorded. The postoperative nasal length was significantly elongated from 47.0±10.4 mm to 49.3±10.1 mm (p=0.003), and the nasal height increased significantly from 48.5±9.1 mm to 50.4±8.5 mm (p=0.011). The initially obtuse columella-labial angle improved significantly from 100.8°±12.1° to 92.5°±15.5° (p=0.014). No significant changes were found regarding nasal projection, nasal tip angle, or columella-lobular angle. The majority of the patients (91.3%) were highly satisfied or satisfied with the aesthetic results. A major complication in terms of implant exposure was observed in one case. The minor complications included stiffness of the nasal tip (3 patients) and tip redness (1 patient). In Oriental nose elongation, the use of an L-shaped graft is a feasible and safe treatment option that allows for an excellent aesthetic outcome and reduces the incidence of complications. This journal requires that authors assign a level of evidence to each submission to which Evidence-Based Medicine rankings are applicable. This excludes Review Articles, Book Reviews, and manuscripts that concern Basic Science, Animal Studies, Cadaver Studies, and Experimental Studies. For a full description of these Evidence-Based Medicine ratings, please refer to the Table of Contents or the online Instructions to Authors www.springer.com/00266 .

40 CFR 64.4 - Submittal requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

... proposed to satisfy § 64.3(b)(2) or (3) include differences from manufacturer recommendations, the owner or operator shall explain the reasons for the differences between the requirements proposed by the owner or... conditions representative of maximum emissions potential under anticipated operating conditions at the...

40 CFR 64.4 - Submittal requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

... proposed to satisfy § 64.3(b)(2) or (3) include differences from manufacturer recommendations, the owner or operator shall explain the reasons for the differences between the requirements proposed by the owner or... conditions representative of maximum emissions potential under anticipated operating conditions at the...

Federal Contractors and Sticky Costs

DTIC Science & Technology

2014-11-05

products such as toothpaste which do not require satisfying unique federal requirements (and related paperwork). For these reasons, it may not be...sales tend to be for off-the-shelf items such as toothpaste . Proctor and Gamble may not need to deal with issues involving government-specific

13 CFR 127.504 - What additional requirements must a concern satisfy to submit an offer on an EDWOSB or WOSB...

Code of Federal Regulations, 2011 CFR

2011-01-01

... Business Credit and Assistance SMALL BUSINESS ADMINISTRATION WOMEN-OWNED SMALL BUSINESS FEDERAL CONTRACT... eligibility; and (d) It will meet the applicable percentages of work requirement as set forth in § 125.6 of...

13 CFR 127.504 - What additional requirements must a concern satisfy to submit an offer on an EDWOSB or WOSB...

Code of Federal Regulations, 2010 CFR

2010-01-01

... Business Credit and Assistance SMALL BUSINESS ADMINISTRATION WOMEN-OWNED SMALL BUSINESS FEDERAL CONTRACT... eligibility; and (d) It will meet the applicable percentages of work requirement as set forth in § 125.6 of...

45 CFR 146.117 - Special enrollment periods.

Code of Federal Regulations, 2010 CFR

2010-10-01

... coverage under any group health plan or health insurance coverage; and (C) The employee satisfies the... REQUIREMENTS FOR THE GROUP HEALTH INSURANCE MARKET Requirements Relating to Access and Renewability of Coverage... health insurance issuer offering health insurance coverage in connection with a group health plan, is...

A Trustworthy Internet Auction Model with Verifiable Fairness.

ERIC Educational Resources Information Center

Liao, Gen-Yih; Hwang, Jing-Jang

2001-01-01

Describes an Internet auction model achieving verifiable fairness, a requirement aimed at enhancing the trust of bidders in auctioneers. Analysis results demonstrate that the proposed model satisfies various requirements regarding fairness and privacy. Moreover, in the proposed model, the losing bids remain sealed. (Author/AEF)

IDC System Specification Document.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Clifford, David J.

2014-12-01

This document contains the system specifications derived to satisfy the system requirements found in the IDC System Requirements Document for the IDC Reengineering Phase 2 project. Revisions Version Date Author/Team Revision Description Authorized by V1.0 12/2014 IDC Reengineering Project Team Initial delivery M. Harris

Regulatory requirements for genotoxicity assessment of plant protection product active ingredients, impurities, and metabolites.

PubMed

Booth, Ewan D; Rawlinson, Paul J; Maria Fagundes, Priscila; Leiner, Kevin A

2017-06-01

Active ingredients in plant protection products are subject to rigorous safety assessment during their development, including assessment of genotoxicity. Plant protection products are used for agriculture in multiple regions and for the registration of active ingredients it is necessary to satisfy the data requirements of these different regions. There are no overarching global agreements on which genotoxicity studies need to be conducted to satisfy the majority of regulatory authorities. The implementation of new OECD guidelines for the in vitro micronucleus, transgenic rodent somatic and germ cell gene mutation and in vivo comet assays, as well as the revision of a number of other OECD test guidelines has resulted in some changes to data requirements. This review describes the genotoxicity data requirements for chemical active ingredients as well as biologicals, microbials, ground water metabolites, metabolites, and impurities in a number of regions. Similarities and differences are highlighted. Environ. Mol. Mutagen. 58:325-344, 2017. © 2017 Wiley Periodicals, Inc. © 2017 Wiley Periodicals, Inc.

Operation Condition Monitoring using Temporal Weighted Dempster-Shafer Theory

DTIC Science & Technology

2014-12-23

are mutually exclusive; A mapping of  : 2 0,1m   , which defines the basic probability assignment( BPA ) of each subset A  of hypotheses and...satisfying ( ) 0;m   ( ) 1 A m A   . The BPA represents a certain piece of ev idence. A rule of D-S evidence combination, which could be used to...yield a new BPA from two independent evidences and their BPAs . There are a number of possible combination rules in application (Sentz, 2002). One

NASA Astrophysics Data System (ADS)

2018-05-01

Eigenvalues and eigenvectors, together, constitute the eigenstructure of the system. The design of vibrating systems aimed at satisfying specifications on eigenvalues and eigenvectors, which is commonly known as eigenstructure assignment, has drawn increasing interest over the recent years. The most natural mathematical framework for such problems is constituted by the inverse eigenproblems, which consist in the determination of the system model that features a desired set of eigenvalues and eigenvectors. Although such a problem is intrinsically challenging, several solutions have been proposed in the literature. The approaches to eigenstructure assignment can be basically divided into passive control and active control.

Analyzing the Commitment of College Students Using a Brief, Contextualized Measure of Need Satisfaction From the Perspective of Self-Determination Theory.

PubMed

Davidson, William; Beck, Hall P

2018-01-01

This study empirically confirmed the relationships between the degree to which students satisfied three basic needs (competence, relatedness, and autonomy) and the strength of their commitments to the university they attended and to obtaining a baccalaureate degree. A questionnaire was administered online to 1257 students at two 4-year universities. Regression analysis yielded statistically significant associations between the three needs and Institutional Commitment and Degree Commitment, explaining more than 20% of the variance in the latter two variables.

Safe Onboard Guidance and Control Under Probabilistic Uncertainty

NASA Technical Reports Server (NTRS)

Blackmore, Lars James

2011-01-01

An algorithm was developed that determines the fuel-optimal spacecraft guidance trajectory that takes into account uncertainty, in order to guarantee that mission safety constraints are satisfied with the required probability. The algorithm uses convex optimization to solve for the optimal trajectory. Convex optimization is amenable to onboard solution due to its excellent convergence properties. The algorithm is novel because, unlike prior approaches, it does not require time-consuming evaluation of multivariate probability densities. Instead, it uses a new mathematical bounding approach to ensure that probability constraints are satisfied, and it is shown that the resulting optimization is convex. Empirical results show that the approach is many orders of magnitude less conservative than existing set conversion techniques, for a small penalty in computation time.

Analysis of Forgery Attack on One-Time Proxy Signature and the Improvement

NASA Astrophysics Data System (ADS)

Wang, Tian-Yin; Wei, Zong-Li

2016-02-01

In a recent paper, Yang et al. (Quant. Inf. Process. 13(9), 2007-2016, 2014) analyzed the security of one-time proxy signature scheme Wang and Wei (Quant. Inf. Process. 11(2), 455-463, 2012) and pointed out that it cannot satisfy the security requirements of unforgeability and undeniability because an eavesdropper Eve can forge a valid proxy signature on a message chosen by herself. However, we find that the so-called proxy message-signature pair forged by Eve is issued by the proxy signer in fact, and anybody can obtain it as a requester, which means that the forgery attack is not considered as a successful attack. Therefore, the conclusion that this scheme cannot satisfy the security requirements of proxy signature against forging and denying is not appropriate in this sense. Finally, we study the reason for the misunderstanding and clarify the security requirements for proxy signatures.

Test and Validation of the Mars Science Laboratory Robotic Arm

NASA Technical Reports Server (NTRS)

Robinson, M.; Collins, C.; Leger, P.; Kim, W.; Carsten, J.; Tompkins, V.; Trebi-Ollennu, A.; Florow, B.

2013-01-01

The Mars Science Laboratory Robotic Arm (RA) is a key component for achieving the primary scientific goals of the mission. The RA supports sample acquisition by precisely positioning a scoop above loose regolith or accurately preloading a percussive drill on Martian rocks or rover-mounted organic check materials. It assists sample processing by orienting a sample processing unit called CHIMRA through a series of gravity-relative orientations and sample delivery by positioning the sample portion door above an instrument inlet or the observation tray. In addition the RA facilitates contact science by accurately positioning the dust removal tool, Alpha Particle X-Ray Spectrometer (APXS) and the Mars Hand Lens Imager (MAHLI) relative to surface targets. In order to fulfill these seemingly disparate science objectives the RA must satisfy a variety of accuracy and performance requirements. This paper describes the necessary arm requirement specification and the test campaign to demonstrate these requirements were satisfied.

Issues to be addressed in the design and fabrication of ultralightweight meter-class optics

NASA Astrophysics Data System (ADS)

Krumweide, Gary C.

1998-08-01

There is a growing need for large aperture, ultralightweight, deployable optics for various science, military and commercial compact satellites. This paper will examine the engineering and manufacturing considerations that must be addressed in order to satisfy the requirements for these sought after optics. In order to limit the scope of this paper, only Graphite Fiber Reinforced/Polymer Matrix Composites (GFR/PMC) will be under consideration because of the potential to satisfy ultralightweight mirror requirements. The requirements associated with specular mirror concepts that Composite Optics, Incorporated (COI) has proposed to Air Force Research Laboratory and NASA Langley Research Center for visible range optics and LIDAR optics, respectively, will also be our interest. Moreover, it is the intent of this paper to illustrate how COI's proposed design/manufacturing concepts for visible and LIDAR optics have evolved based on overcoming, or working around, material constraints and/or undesirable characteristics associated with GFR/PMC.

26 CFR 1.9101-1 - Permission to submit information required by certain returns and statements on magnetic tape.

Code of Federal Regulations, 2014 CFR

2014-04-01

... satisfied by submitting the information required by such form on magnetic tape or by other media, provided... submitting the information required by such form on magnetic tape or other approved media, provided that the prior consent of the Commissioner of Social Security (or other authorized officer or employee thereof...

26 CFR 1.9101-1 - Permission to submit information required by certain returns and statements on magnetic tape.

Code of Federal Regulations, 2013 CFR

2013-04-01

... satisfied by submitting the information required by such form on magnetic tape or by other media, provided... submitting the information required by such form on magnetic tape or other approved media, provided that the prior consent of the Commissioner of Social Security (or other authorized officer or employee thereof...

26 CFR 1.9101-1 - Permission to submit information required by certain returns and statements on magnetic tape.

Code of Federal Regulations, 2011 CFR

2011-04-01

... satisfied by submitting the information required by such form on magnetic tape or by other media, provided... submitting the information required by such form on magnetic tape or other approved media, provided that the prior consent of the Commissioner of Social Security (or other authorized officer or employee thereof...

26 CFR 1.9101-1 - Permission to submit information required by certain returns and statements on magnetic tape.

Code of Federal Regulations, 2012 CFR

2012-04-01

... satisfied by submitting the information required by such form on magnetic tape or by other media, provided... submitting the information required by such form on magnetic tape or other approved media, provided that the prior consent of the Commissioner of Social Security (or other authorized officer or employee thereof...

75 FR 232 - Finding of Failure To Submit Certain State Implementation Plans Required for the 1-Hour Ozone NAAQS

Federal Register 2010, 2011, 2012, 2013, 2014

2010-01-05

... Failure To Submit Certain State Implementation Plans Required for the 1-Hour Ozone NAAQS AGENCY...) for three ozone nonattainment areas to satisfy certain requirements of the Clean Air Act (CAA) for the 1-hour ozone National Ambient Air Quality Standards (NAAQS). To accompany this action we are issuing...

40 CFR 265.256 - Special requirements for ignitable or reactive waste.

Code of Federal Regulations, 2010 CFR

2010-07-01

... TREATMENT, STORAGE, AND DISPOSAL FACILITIES Waste Piles § 265.256 Special requirements for ignitable or reactive waste. (a) Ignitable or reactive waste must not be placed in a pile unless the waste and pile satisfy all applicable requirements of 40 CFR part 268, and: (1) Addition of the waste to an existing pile...

26 CFR 1.401-3 - Requirements as to coverage.

Code of Federal Regulations, 2011 CFR

2011-04-01

... qualified unless it is part of a plan which satisfies the coverage requirements of section 401(a)(3... corporation adopts a plan at a time when it has 1,000 employees. The plan provides that all full-time.... (b) If a plan fails to qualify under the percentage requirements of section 401(a)(3)(A), it may...

26 CFR 1.401-3 - Requirements as to coverage.

Code of Federal Regulations, 2012 CFR

2012-04-01

... qualified unless it is part of a plan which satisfies the coverage requirements of section 401(a)(3... corporation adopts a plan at a time when it has 1,000 employees. The plan provides that all full-time.... (b) If a plan fails to qualify under the percentage requirements of section 401(a)(3)(A), it may...

26 CFR 1.401-3 - Requirements as to coverage.

Code of Federal Regulations, 2014 CFR

2014-04-01

... qualified unless it is part of a plan which satisfies the coverage requirements of section 401(a)(3... corporation adopts a plan at a time when it has 1,000 employees. The plan provides that all full-time.... (b) If a plan fails to qualify under the percentage requirements of section 401(a)(3)(A), it may...

26 CFR 1.401-3 - Requirements as to coverage.

Code of Federal Regulations, 2013 CFR

2013-04-01

... qualified unless it is part of a plan which satisfies the coverage requirements of section 401(a)(3... corporation adopts a plan at a time when it has 1,000 employees. The plan provides that all full-time.... (b) If a plan fails to qualify under the percentage requirements of section 401(a)(3)(A), it may...

40 CFR 152.90 - The selective method.

Code of Federal Regulations, 2010 CFR

2010-07-01

... authorizations or offers to pay. Refer to § 152.95. (6) Documentation of a data gap. Refer to § 152.96. [49 FR... data gap. (a) List of data requirements. Each applicant must submit a list of the data requirements... gap procedures in § 152.96 that a conditional requirement need not be satisfied by the submission or...

Integrated network architecture for sustained human and robotic exploration

NASA Technical Reports Server (NTRS)

Noreen, Gary K.; Cesarone, Robert; Deutsch, Leslie; Edwards, Charlie; Soloff, Jason; Ely, Todd; Cook, Brian; Morabito, David; Hemmati, Hamid; Piazzolla, Sabino;

ETS levels in hospitality environments satisfying ASHRAE standard 62-1989: "ventilation for acceptable indoor air quality"

NASA Astrophysics Data System (ADS)

Moschandreas, D. J.; Vuilleumier, K. L.

Prior to this study, indoor air constituent levels and ventilation rates of hospitality environments had not been measured simultaneously. This investigation measured indoor Environmental Tobacco Smoke-related (ETS-related) constituent levels in two restaurants, a billiard hall and a casino. The objective of this study was to characterize ETS-related constituent levels inside hospitality environments when the ventilation rates satisfy the requirements of the ASHRAE 62-1989 Ventilation Standard. The ventilation rate of each selected hospitality environment was measured and adjusted. The study advanced only if the requirements of the ASHRAE 62-1989 Ventilation Standard - the pertinent standard of the American Society of Heating, Refrigeration and Air Conditioning Engineers - were satisfied. The supply rates of outdoor air and occupant density were measured intermittently to assure that the ventilation rate of each facility satisfied the standard under occupied conditions. Six ETS-related constituents were measured: respirable suspended particulate (RSP) matter, fluorescent particulate matter (FPM, an estimate of the ETS particle concentrations), ultraviolet particulate matter (UVPM, a second estimate of the ETS particle concentrations), solanesol, nicotine and 3-ethenylpyridine (3-EP). ETS-related constituent levels in smoking sections, non-smoking sections and outdoors were sampled daily for eight consecutive days at each hospitality environment. This study found that the difference between the concentrations of ETS-related constituents in indoor smoking and non-smoking sections was statistically significant. Differences between indoor non-smoking sections and outdoor ETS-related constituent levels were identified but were not statistically significant. Similarly, differences between weekday and weekend evenings were identified but were not statistically significant. The difference between indoor smoking sections and outdoors was statistically significant. Most importantly, ETS-related constituent concentrations measured indoors did not exceed existing occupational standards. It was concluded that if the measured ventilation rates of the sampled facilities satisfied the ASHRAE 62-1989 Ventilation Standard requirements, the corresponding ETS-related constituents were measured at concentrations below known harmful levels as specified by the American Conference of Governmental Industrial Hygiene (ACGIH).

19 CFR 111.11 - Basic requirements for a license.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 19 Customs Duties 1 2010-04-01 2010-04-01 false Basic requirements for a license. 111.11 Section 111.11 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF HOMELAND SECURITY; DEPARTMENT OF THE TREASURY CUSTOMS BROKERS Procedure To Obtain License or Permit § 111.11 Basic requirements for...

19 CFR 111.11 - Basic requirements for a license.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 19 Customs Duties 1 2012-04-01 2012-04-01 false Basic requirements for a license. 111.11 Section 111.11 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF HOMELAND SECURITY; DEPARTMENT OF THE TREASURY CUSTOMS BROKERS Procedure To Obtain License or Permit § 111.11 Basic requirements for...

19 CFR 111.11 - Basic requirements for a license.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 19 Customs Duties 1 2011-04-01 2011-04-01 false Basic requirements for a license. 111.11 Section 111.11 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF HOMELAND SECURITY; DEPARTMENT OF THE TREASURY CUSTOMS BROKERS Procedure To Obtain License or Permit § 111.11 Basic requirements for...

19 CFR 111.11 - Basic requirements for a license.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 19 Customs Duties 1 2013-04-01 2013-04-01 false Basic requirements for a license. 111.11 Section 111.11 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF HOMELAND SECURITY; DEPARTMENT OF THE TREASURY CUSTOMS BROKERS Procedure To Obtain License or Permit § 111.11 Basic requirements for...

19 CFR 111.11 - Basic requirements for a license.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 19 Customs Duties 1 2014-04-01 2014-04-01 false Basic requirements for a license. 111.11 Section 111.11 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF HOMELAND SECURITY; DEPARTMENT OF THE TREASURY CUSTOMS BROKERS Procedure To Obtain License or Permit § 111.11 Basic requirements for...

Influence of Scale Effect and Model Performance in Downscaling ASTER Land Surface Temperatures to a Very High Spatial Resolution in an Agricultural Area

NASA Astrophysics Data System (ADS)

Zhou, J.; Li, G.; Liu, S.; Zhan, W.; Zhang, X.

2015-12-01

At present land surface temperatures (LSTs) can be generated from thermal infrared remote sensing with spatial resolutions from ~100 m to tens of kilometers. However, LSTs with high spatial resolution, e.g. tens of meters, are still lack. The purpose of LST downscaling is to generate LSTs with finer spatial resolutions than their native spatial resolutions. The statistical linear or nonlinear regression models are most frequently used for LST downscaling. The basic assumption of these models is the scale-invariant relationships between LST and its descriptors, which is questioned but rare researches have been reported. In addition, few researches can be found for downscaling satellite LST or TIR data to a high spatial resolution, i.e. better than 100 m or even finer. The lack of LST with high spatial resolution cannot satisfy the requirements of applications such as evapotranspiration mapping at the field scale. By selecting a dynamically developing agricultural oasis as the study area, the aim of this study is to downscale the Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) LSTs to 15 m, to satisfy the requirement of evapotranspiration mapping at the field scale. Twelve ASTER images from May to September in 2012, covering the entire growth stage of maize, were selected. Four statistical models were evaluated, including one global model, one piecewise model, and two local models. The influence from scale effect in downscaling LST was quantified. The downscaled LSTs are evaluated from accuracy and image quality. Results demonstrate that the influence from scale effect varies according to models and the maize growth stage. Significant influence about -4 K to 6 K existed at the early stage and weaker influence existed in the middle stage. When compared with the ground measured LSTs, the downscaled LSTs resulted from the global and local models yielded higher accuracies and better image qualities than the local models. In addition to the vegetation indices, the surface albedo is an important descriptor for downscaling LST through explaining its spatial variation induced by soil moisture.

PCIPS 2.0: Powerful multiprofile image processing implemented on PCs

NASA Technical Reports Server (NTRS)

Smirnov, O. M.; Piskunov, N. E.

1992-01-01

Over the years, the processing power of personal computers has steadily increased. Now, 386- and 486-based PC's are fast enough for many image processing applications, and inexpensive enough even for amateur astronomers. PCIPS is an image processing system based on these platforms that was designed to satisfy a broad range of data analysis needs, while requiring minimum hardware and providing maximum expandability. It will run (albeit at a slow pace) even on a 80286 with 640K memory, but will take full advantage of bigger memory and faster CPU's. Because the actual image processing is performed by external modules, the system can be easily upgraded by the user for all sorts of scientific data analysis. PCIPS supports large format lD and 2D images in any numeric type from 8-bit integer to 64-bit floating point. The images can be displayed, overlaid, printed and any part of the data examined via an intuitive graphical user interface that employs buttons, pop-up menus, and a mouse. PCIPS automatically converts images between different types and sizes to satisfy the requirements of various applications. PCIPS features an API that lets users develop custom applications in C or FORTRAN. While doing so, a programmer can concentrate on the actual data processing, because PCIPS assumes responsibility for accessing images and interacting with the user. This also ensures that all applications, even custom ones, have a consistent and user-friendly interface. The API is compatible with factory programming, a metaphor for constructing image processing procedures that will be implemented in future versions of the system. Several application packages were created under PCIPS. The basic package includes elementary arithmetics and statistics, geometric transformations and import/export in various formats (FITS, binary, ASCII, and GIF). The CCD processing package and the spectral analysis package were successfully used to reduce spectra from the Nordic Telescope at La Palma. A photometry package is also available, and other packages are being developed. A multitasking version of PCIPS that utilizes the factory programming concept is currently under development. This version will remain compatible (on the source code level) with existing application packages and custom applications.

Characterization and optimization of the magnetron directional amplifier

NASA Astrophysics Data System (ADS)

Hatfield, Michael Craig

Many applications of microwave wireless power transmission (WPT) are dependent upon a high-powered electronically-steerable phased array composed of many radiating modules. The phase output from the high-gain amplifier in each module must be accurately controlled if the beam is to be properly steered. A highly reliable, rugged, and inexpensive design is essential for making WPT applications practical. A conventional microwave oven magnetron may be combined with a ferrite circulator and other external circuitry to create such a system. By converting it into a two-port amplifier, the magnetron is capable of delivering at least 30 dB of power gain while remaining phase-locked to the input signal over a wide frequency range. The use of the magnetron in this manner is referred to as a MDA (Magnetron Directional Amplifier). The MDA may be integrated with an inexpensive slotted waveguide array (SWA) antenna to form the Electronically-Steerable Phased Array Module (ESPAM). The ESPAM provides a building block approach to creating phased arrays for WPT. The size and shape of the phased array may be tailored to satisfy a diverse range of applications. This study provided an in depth examination into the capabilities of the MDA/ESPAM. The basic behavior of the MDA was already understood, as well as its potential applicability to WPT. The primary objective of this effort was to quantify how well the MDA could perform in this capacity. Subordinate tasks included characterizing the MDA behavior in terms of its system inputs, optimizing its performance, performing sensitivity analyses, and identifying operating limitations. A secondary portion of this study examined the suitability of the ESPAM in satisfying system requirements for the solar power satellite (SPS). Supporting tasks included an analysis of SPS requirements, modeling of the SWA antenna, and the demonstration of a simplified phased array constructed of ESPAM elements. The MDA/ESPAM is well suited for use as an amplifier or an element in a WPT phased array, providing over 75% efficiency and a fractional bandwidth exceeding 1.7% at 2.45 GHz. The results of this effort provide the WPT design engineer with tools to predict the MDA's optimum performance and limitations.

Control system design for flexible structures using data models

NASA Technical Reports Server (NTRS)

Irwin, R. Dennis; Frazier, W. Garth; Mitchell, Jerrel R.; Medina, Enrique A.; Bukley, Angelia P.

1993-01-01

The dynamics and control of flexible aerospace structures exercises many of the engineering disciplines. In recent years there has been considerable research in the developing and tailoring of control system design techniques for these structures. This problem involves designing a control system for a multi-input, multi-output (MIMO) system that satisfies various performance criteria, such as vibration suppression, disturbance and noise rejection, attitude control and slewing control. Considerable progress has been made and demonstrated in control system design techniques for these structures. The key to designing control systems for these structures that meet stringent performance requirements is an accurate model. It has become apparent that theoretically and finite-element generated models do not provide the needed accuracy; almost all successful demonstrations of control system design techniques have involved using test results for fine-tuning a model or for extracting a model using system ID techniques. This paper describes past and ongoing efforts at Ohio University and NASA MSFC to design controllers using 'data models.' The basic philosophy of this approach is to start with a stabilizing controller and frequency response data that describes the plant; then, iteratively vary the free parameters of the controller so that performance measures become closer to satisfying design specifications. The frequency response data can be either experimentally derived or analytically derived. One 'design-with-data' algorithm presented in this paper is called the Compensator Improvement Program (CIP). The current CIP designs controllers for MIMO systems so that classical gain, phase, and attenuation margins are achieved. The center-piece of the CIP algorithm is the constraint improvement technique which is used to calculate a parameter change vector that guarantees an improvement in all unsatisfied, feasible performance metrics from iteration to iteration. The paper also presents a recently demonstrated CIP-type algorithm, called the Model and Data Oriented Computer-Aided Design System (MADCADS), developed for achieving H(sub infinity) type design specifications using data models. Control system design for the NASA/MSFC Single Structure Control Facility are demonstrated for both CIP and MADCADS. Advantages of design-with-data algorithms over techniques that require analytical plant models are also presented.

iSPHERE - A New Approach to Collaborative Research and Cloud Computing

NASA Astrophysics Data System (ADS)

Al-Ubaidi, T.; Khodachenko, M. L.; Kallio, E. J.; Harry, A.; Alexeev, I. I.; Vázquez-Poletti, J. L.; Enke, H.; Magin, T.; Mair, M.; Scherf, M.; Poedts, S.; De Causmaecker, P.; Heynderickx, D.; Congedo, P.; Manolescu, I.; Esser, B.; Webb, S.; Ruja, C.

2015-10-01

The project iSPHERE (integrated Scientific Platform for HEterogeneous Research and Engineering) that has been proposed for Horizon 2020 (EINFRA-9- 2015, [1]) aims at creating a next generation Virtual Research Environment (VRE) that embraces existing and emerging technologies and standards in order to provide a versatile platform for scientific investigations and collaboration. The presentation will introduce the large project consortium, provide a comprehensive overview of iSPHERE's basic concepts and approaches and outline general user requirements that the VRE will strive to satisfy. An overview of the envisioned architecture will be given, focusing on the adapted Service Bus concept, i.e. the "Scientific Service Bus" as it is called in iSPHERE. The bus will act as a central hub for all communication and user access, and will be implemented in the course of the project. The agile approach [2] that has been chosen for detailed elaboration and documentation of user requirements, as well as for the actual implementation of the system, will be outlined and its motivation and basic structure will be discussed. The presentation will show which user communities will benefit and which concrete problems, scientific investigations are facing today, will be tackled by the system. Another focus of the presentation is iSPHERE's seamless integration of cloud computing resources and how these will benefit scientific modeling teams by providing a reliable and web based environment for cloud based model execution, storage of results, and comparison with measurements, including fully web based tools for data mining, analysis and visualization. Also the envisioned creation of a dedicated data model for experimental plasma physics will be discussed. It will be shown why the Scientific Service Bus provides an ideal basis to integrate a number of data models and communication protocols and to provide mechanisms for data exchange across multiple and even multidisciplinary platforms.

SigWin-detector: a Grid-enabled workflow for discovering enriched windows of genomic features related to DNA sequences.

PubMed

Inda, Márcia A; van Batenburg, Marinus F; Roos, Marco; Belloum, Adam S Z; Vasunin, Dmitry; Wibisono, Adianto; van Kampen, Antoine H C; Breit, Timo M

2008-08-08

Chromosome location is often used as a scaffold to organize genomic information in both the living cell and molecular biological research. Thus, ever-increasing amounts of data about genomic features are stored in public databases and can be readily visualized by genome browsers. To perform in silico experimentation conveniently with this genomics data, biologists need tools to process and compare datasets routinely and explore the obtained results interactively. The complexity of such experimentation requires these tools to be based on an e-Science approach, hence generic, modular, and reusable. A virtual laboratory environment with workflows, workflow management systems, and Grid computation are therefore essential. Here we apply an e-Science approach to develop SigWin-detector, a workflow-based tool that can detect significantly enriched windows of (genomic) features in a (DNA) sequence in a fast and reproducible way. For proof-of-principle, we utilize a biological use case to detect regions of increased and decreased gene expression (RIDGEs and anti-RIDGEs) in human transcriptome maps. We improved the original method for RIDGE detection by replacing the costly step of estimation by random sampling with a faster analytical formula for computing the distribution of the null hypothesis being tested and by developing a new algorithm for computing moving medians. SigWin-detector was developed using the WS-VLAM workflow management system and consists of several reusable modules that are linked together in a basic workflow. The configuration of this basic workflow can be adapted to satisfy the requirements of the specific in silico experiment. As we show with the results from analyses in the biological use case on RIDGEs, SigWin-detector is an efficient and reusable Grid-based tool for discovering windows enriched for features of a particular type in any sequence of values. Thus, SigWin-detector provides the proof-of-principle for the modular e-Science based concept of integrative bioinformatics experimentation.

Implementing ICAO Language Proficiency Requirements in the Versant Aviation English Test

ERIC Educational Resources Information Center

Van Moere, Alistair; Suzuki, Masanori; Downey, Ryan; Cheng, Jian

2009-01-01

This paper discusses the development of an assessment to satisfy the International Civil Aviation Organization (ICAO) Language Proficiency Requirements. The Versant Aviation English Test utilizes speech recognition technology and a computerized testing platform, such that test administration and scoring are fully automated. Developed in…

26 CFR 1.1295-3 - Retroactive elections.

Code of Federal Regulations, 2010 CFR

2010-04-01

... rules require that the shareholder possess reasonable belief as of the election due date that the... reasonable belief that a foreign corporation was not a PFIC. Paragraph (e) of this section prescribes special rules for certain shareholders that are deemed to satisfy the reasonable belief requirement and...

41 CFR 301-11.18 - What M&IE rate will I receive if a meal(s) is furnished by the Government or is included in the...

Code of Federal Regulations, 2012 CFR

2012-07-01

... medical requirements or religious beliefs; (2) In accordance with administrative procedures prescribed by... meals in order to satisfy your medical requirements or religious beliefs. (c) In your agency's...

41 CFR 301-11.18 - What M&IE rate will I receive if a meal(s) is furnished by the Government or is included in the...

Code of Federal Regulations, 2014 CFR

2014-07-01

... medical requirements or religious beliefs; (2) In accordance with administrative procedures prescribed by... meals in order to satisfy your medical requirements or religious beliefs. (c) In your agency's...

41 CFR 301-11.18 - What M&IE rate will I receive if a meal(s) is furnished by the Government or is included in the...

Code of Federal Regulations, 2013 CFR

2013-07-01

... medical requirements or religious beliefs; (2) In accordance with administrative procedures prescribed by... meals in order to satisfy your medical requirements or religious beliefs. (c) In your agency's...

40 CFR 86.016-1 - General applicability.

Code of Federal Regulations, 2012 CFR

2012-07-01

... solar-powered vehicles. Use good engineering judgment to apply these requirements to these vehicles... (CONTINUED) CONTROL OF EMISSIONS FROM NEW AND IN-USE HIGHWAY VEHICLES AND ENGINES General Provisions for... the manufacturer satisfies the requirements of § 86.007-23(f). (3) When a manufacturer chooses to use...

40 CFR 86.016-1 - General applicability.

Code of Federal Regulations, 2013 CFR

2013-07-01

... solar-powered vehicles. Use good engineering judgment to apply these requirements to these vehicles... (CONTINUED) CONTROL OF EMISSIONS FROM NEW AND IN-USE HIGHWAY VEHICLES AND ENGINES General Provisions for... the manufacturer satisfies the requirements of § 86.007-23(f). (3) When a manufacturer chooses to use...

10 CFR 71.101 - Quality assurance requirements.

Code of Federal Regulations, 2010 CFR

2010-01-01

... quality assurance actions related to control of the physical characteristics and quality of the material... through 71.137 and satisfying any specific provisions that are applicable to the licensee's activities... assurance requirement's importance to safety. (c) Approval of program. (1) Before the use of any package for...

40 CFR 158.70 - Satisfying data requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... the data requirement. In evaluating experimental design, the Agency will consider whether generally... specified in this part are acceptable. This determination will be based on the design and conduct of the... conduct of each experiment in terms of whether the study was conducted in conformance with the design...

40 CFR 158.70 - Satisfying data requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

... the data requirement. In evaluating experimental design, the Agency will consider whether generally... specified in this part are acceptable. This determination will be based on the design and conduct of the... conduct of each experiment in terms of whether the study was conducted in conformance with the design...

40 CFR 158.70 - Satisfying data requirements.

Code of Federal Regulations, 2012 CFR

2012-07-01

... the data requirement. In evaluating experimental design, the Agency will consider whether generally... specified in this part are acceptable. This determination will be based on the design and conduct of the... conduct of each experiment in terms of whether the study was conducted in conformance with the design...

40 CFR 158.70 - Satisfying data requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

... the data requirement. In evaluating experimental design, the Agency will consider whether generally... specified in this part are acceptable. This determination will be based on the design and conduct of the... conduct of each experiment in terms of whether the study was conducted in conformance with the design...

40 CFR 158.70 - Satisfying data requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

... the data requirement. In evaluating experimental design, the Agency will consider whether generally... specified in this part are acceptable. This determination will be based on the design and conduct of the... conduct of each experiment in terms of whether the study was conducted in conformance with the design...

Intentionally Short-Range Communications (ISRC) exploratory development plan

NASA Astrophysics Data System (ADS)

Yen, J.

1992-06-01

This document is an exploratory development plan for the Intentionally Short-Range Communications (ISRC) project. The USMC requirements and project objectives are quantified, then possible solutions identified and developed. Some of these ideas will be attempted to determine the best option(s) satisfying the USMC requirements.

23 CFR 1313.7 - Requirements for a high fatality rate state.

Code of Federal Regulations, 2010 CFR

2010-04-01

... Section 1313.7 Highways NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION INCENTIVE GRANT CRITERIA FOR ALCOHOL-IMPAIRED DRIVING PREVENTION PROGRAMS § 1313.7 Requirements for a high... driving enforcement campaign in accordance with § 1313.6(a) and include information that satisfies the...

45 CFR 152.14 - Eligibility.

Code of Federal Regulations, 2011 CFR

2011-10-01

... have satisfied the requirement in paragraph (a)(2) of this section for purposes of applying to enroll in a PCIP in the new service area. (c) Pre-existing condition requirement. For purposes of... condition for purposes of this section: (1) Refusal of coverage. Documented evidence that an insurer has...

14 CFR 142.49 - Training center instructor and evaluator privileges and limitations.

Code of Federal Regulations, 2010 CFR

2010-01-01

... and Flight Training Equipment Requirements § 142.49 Training center instructor and evaluator... each curriculum for which that instructor is qualified. (2) Testing and checking for which that instructor is qualified. (3) Instruction, testing, and checking intended to satisfy the requirements of any...

14 CFR 142.49 - Training center instructor and evaluator privileges and limitations.

Code of Federal Regulations, 2011 CFR

2011-01-01

... and Flight Training Equipment Requirements § 142.49 Training center instructor and evaluator... each curriculum for which that instructor is qualified. (2) Testing and checking for which that instructor is qualified. (3) Instruction, testing, and checking intended to satisfy the requirements of any...

14 CFR 142.49 - Training center instructor and evaluator privileges and limitations.

Code of Federal Regulations, 2014 CFR

2014-01-01

... and Flight Training Equipment Requirements § 142.49 Training center instructor and evaluator... each curriculum for which that instructor is qualified. (2) Testing and checking for which that instructor is qualified. (3) Instruction, testing, and checking intended to satisfy the requirements of any...

14 CFR 142.49 - Training center instructor and evaluator privileges and limitations.

Code of Federal Regulations, 2012 CFR

2012-01-01

... and Flight Training Equipment Requirements § 142.49 Training center instructor and evaluator... each curriculum for which that instructor is qualified. (2) Testing and checking for which that instructor is qualified. (3) Instruction, testing, and checking intended to satisfy the requirements of any...

14 CFR 142.49 - Training center instructor and evaluator privileges and limitations.

Code of Federal Regulations, 2013 CFR

2013-01-01

... and Flight Training Equipment Requirements § 142.49 Training center instructor and evaluator... each curriculum for which that instructor is qualified. (2) Testing and checking for which that instructor is qualified. (3) Instruction, testing, and checking intended to satisfy the requirements of any...

Enhancements of evolutionary algorithm for the complex requirements of a nurse scheduling problem

NASA Astrophysics Data System (ADS)

Tein, Lim Huai; Ramli, Razamin

2014-12-01

Over the years, nurse scheduling is a noticeable problem that is affected by the global nurse turnover crisis. The more nurses are unsatisfied with their working environment the more severe the condition or implication they tend to leave. Therefore, the current undesirable work schedule is partly due to that working condition. Basically, there is a lack of complimentary requirement between the head nurse's liability and the nurses' need. In particular, subject to highly nurse preferences issue, the sophisticated challenge of doing nurse scheduling is failure to stimulate tolerance behavior between both parties during shifts assignment in real working scenarios. Inevitably, the flexibility in shifts assignment is hard to achieve for the sake of satisfying nurse diverse requests with upholding imperative nurse ward coverage. Hence, Evolutionary Algorithm (EA) is proposed to cater for this complexity in a nurse scheduling problem (NSP). The restriction of EA is discussed and thus, enhancement on the EA operators is suggested so that the EA would have the characteristic of a flexible search. This paper consists of three types of constraints which are the hard, semi-hard and soft constraints that can be handled by the EA with enhanced parent selection and specialized mutation operators. These operators and EA as a whole contribute to the efficiency of constraint handling, fitness computation as well as flexibility in the search, which correspond to the employment of exploration and exploitation principles.

Development of Ni-Ba(Zr,Y)O3 cermet anodes for direct ammonia-fueled solid oxide fuel cells

NASA Astrophysics Data System (ADS)

Miyazaki, Kazunari; Okanishi, Takeou; Muroyama, Hiroki; Matsui, Toshiaki; Eguchi, Koichi

2017-10-01

In this study, the availability of Ni-Ba(Zr,Y)O3-δ (BZY) cermet for the anode of direct ammonia-fueled solid oxide fuel cells (SOFCs) is evaluated. In this device, the anodes need to be active for the catalytic ammonia decomposition as well as the electrochemical hydrogen oxidation. In the catalytic activity test, ammonia decomposes completely over Ni-BZY at ca. 600 °C, while higher temperature is required to accomplish the complete decomposition over the conventional SOFC anode of Ni-yttria-stabilized zirconia cermet. The high activity of Ni-BZY is attributed to the high basicity of BZY and the high resistance to hydrogen poisoning effect. The electrochemical property of Ni-BZY anode is also evaluated with the anode-supported cell of Ni-BZY|BZY|Pt at 600-700 °C with feeding ammonia or hydrogen as a fuel. Since the residence time of ammonia fuel in the thick Ni-BZY anode is long, the difference in the cell performance between two fuels is relatively small. Furthermore, it is proved that the steam concentration in the fuel strongly affects the cell performance. We find that this factor is important to satisfy the above mentioned requirements for the anode of direct ammonia-fueled SOFCs. Throughout this study, it is concluded that Ni-BZY cermet will be a promising anode.

Additive Layer Manufacturing for Launcher's Applications

NASA Astrophysics Data System (ADS)

Vilanova, J.; Romera, P.; Lasagni, F.; Zorrilla, A.; Perinan, A.

2014-06-01

In the next years the European space industry has the challenge of maintaining its competitiveness in launch vehicles (LV) production, due to the growth of competition worldwide. It has to assure its position developing new applied technologies. In this field the effort is focussed on the production of short series of customized products, like payloads, flight components or launcher parts. ALM (Additive Layer Manufacturing) could be a powerful tool that offers new competitiveness factors for this industry, comprising a set of emerging technologies that are becoming a competitor to forming, casting and machining as well as being utilised directly as a complementary alternative.Originally used for prototypes and models, now ALM becomes a very useful technology capable to fabricate functional parts for the space industrial sector. Its demands on rapid technologies are different to "earth" industries, and they aren't so easily satisfied because space is a field with different requirements depending on its application: launchers, reusable vehicles, satellites, probes, low gravity researches, manned spacecraft, or even moon and planetary exploration.This paper reports on the ALM potential applications, under ESA requirements, exploring the challenges and possibilities for its use in the launchers market, trying to answer two basic questions: the first one, whether ALM is a mature technology to be ready for its use as flight hardware; and the second one, if it can be used to reduce the product cycle, and consequently, the development, production and operational costs.

Lightweight, Mesoporous, and Highly Absorptive All-Nanofiber Aerogel for Efficient Solar Steam Generation.

PubMed

Jiang, Feng; Liu, He; Li, Yiju; Kuang, Yudi; Xu, Xu; Chen, Chaoji; Huang, Hao; Jia, Chao; Zhao, Xinpeng; Hitz, Emily; Zhou, Yubing; Yang, Ronggui; Cui, Lifeng; Hu, Liangbing

2018-01-10

The global fresh water shortage has driven enormous endeavors in seawater desalination and wastewater purification; among these, solar steam generation is effective in extracting fresh water by efficient utilization of naturally abundant solar energy. For solar steam generation, the primary focus is to design new materials that are biodegradable, sustainable, of low cost, and have high solar steam generation efficiency. Here, we designed a bilayer aerogel structure employing naturally abundant cellulose nanofibrils (CNFs) as basic building blocks to achieve sustainability and biodegradability as well as employing a carbon nanotube (CNT) layer for efficient solar utilization with over 97.5% of light absorbance from 300 to 1200 nm wavelength. The ultralow density (0.0096 g/cm 3 ) of the aerogel ensures that minimal material is required, reducing the production cost while at the same time satisfying the water transport and thermal-insulation requirements due to its highly porous structure (99.4% porosity). Owing to its rationally designed structure and thermal-regulation performance, the bilayer CNF-CNT aerogel exhibits a high solar-energy conversion efficiency of 76.3% and 1.11 kg m -2 h -1 at 1 kW m -2 (1 Sun) solar irradiation, comparable or even higher than most of the reported solar steam generation devices. Therefore, the all-nanofiber aerogel presents a new route for designing biodegradable, sustainable, and scalable solar steam generation devices with superb performance.

Deployable Crew Quarters

NASA Technical Reports Server (NTRS)

Izenson, Michael G.; Chen, Weibo

2008-01-01

The deployable crew quarters (DCQ) have been designed for the International Space Station (ISS). Each DCQ would be a relatively inexpensive, deployable boxlike structure that is designed to fit in a rack bay. It is to be occupied by one crewmember to provide privacy and sleeping functions for the crew. A DCQ comprises mostly hard panels, made of a lightweight honeycomb or matrix/fiber material, attached to each other by cloth hinges. Both faces of each panel are covered with a layer of Nomex cloth and noise-suppression material to provide noise isolation from ISS. On Earth, the unit is folded flat and attached to a rigid pallet for transport to the ISS. On the ISS, crewmembers unfold the unit and install it in place, attaching it to ISS structural members by use of soft cords (which also help to isolate noise and vibration). A few hard pieces of equipment (principally, a ventilator and a smoke detector) are shipped separately and installed in the DCQ unit by use of a system of holes, slots, and quarter-turn fasteners. Full-scale tests showed that the time required to install a DCQ unit amounts to tens of minutes. The basic DCQ design could be adapted to terrestrial applications to satisfy requirements for rapid deployable emergency shelters that would be lightweight, portable, and quickly erected. The Temporary Early Sleep Station (TeSS) currently on-orbit is a spin-off of the DCQ.

Health information in Italian public health websites: moving from inaccessibility to accessibility.

PubMed

Mancini, Cristina; Zedda, Monica; Barbaro, Annarita

2005-12-01

In January 2004, the Italian government passed new legislation designed to give people with disabilities access to online services. Starting from the new legislation requirements, the purpose of this study is to investigate whether Italian Local Health Authorities websites are accessible to users with different abilities. One hundred and seventy websites were analysed evaluating their compliance to the World Wide Web Consortium (W3C) Priority 1 guidelines via a combination of appropriate accessibility testing methods. This review was carried out twice: the first time it took place between the end of 2003 and May-June 2004. The same survey was repeated again in December 2004, after the issuing of the draft of the Implementation Regulations for The Stanca Law in July 2004. In this second survey, all the websites analysed before were checked again to establish if some measures to make those sites accessible were taken. Seventy-six per cent of the analysed websites fail to satisfy the most basic W3C requirements, but Italian Local Health Authorities websites are likely to present significant improvements to access for some disabled user groups: the number of accessible websites increased consistently between the first and the second review. It seems that awareness of web accessibility issues is increasing among developers of health information websites because of law enforcement. Recommendations for future research and development are offered.

Combining environment-driven adaptation and task-driven optimisation in evolutionary robotics.

PubMed

Haasdijk, Evert; Bredeche, Nicolas; Eiben, A E

2014-01-01

Embodied evolutionary robotics is a sub-field of evolutionary robotics that employs evolutionary algorithms on the robotic hardware itself, during the operational period, i.e., in an on-line fashion. This enables robotic systems that continuously adapt, and are therefore capable of (re-)adjusting themselves to previously unknown or dynamically changing conditions autonomously, without human oversight. This paper addresses one of the major challenges that such systems face, viz. that the robots must satisfy two sets of requirements. Firstly, they must continue to operate reliably in their environment (viability), and secondly they must competently perform user-specified tasks (usefulness). The solution we propose exploits the fact that evolutionary methods have two basic selection mechanisms-survivor selection and parent selection. This allows evolution to tackle the two sets of requirements separately: survivor selection is driven by the environment and parent selection is based on task-performance. This idea is elaborated in the Multi-Objective aNd open-Ended Evolution (monee) framework, which we experimentally validate. Experiments with robotic swarms of 100 simulated e-pucks show that monee does indeed promote task-driven behaviour without compromising environmental adaptation. We also investigate an extension of the parent selection process with a 'market mechanism' that can ensure equitable distribution of effort over multiple tasks, a particularly pressing issue if the environment promotes specialisation in single tasks.

Discretization and Preconditioning Algorithms for the Euler and Navier-Stokes Equations on Unstructured Meshes

NASA Technical Reports Server (NTRS)

Bart, Timothy J.; Kutler, Paul (Technical Monitor)

1998-01-01

Chapter 1 briefly reviews several related topics associated with the symmetrization of systems of conservation laws and quasi-conservation laws: (1) Basic Entropy Symmetrization Theory; (2) Symmetrization and eigenvector scaling; (3) Symmetrization of the compressible Navier-Stokes equations; and (4) Symmetrization of the quasi-conservative form of the magnetohydrodynamic (MHD) equations. Chapter 2 describes one of the best known tools employed in the study of differential equations, the maximum principle: any function f(x) which satisfies the inequality f(double prime)>0 on the interval [a,b] attains its maximum value at one of the endpoints on the interval. Chapter three examines the upwind finite volume schemes for scalar and system conservation laws. The basic tasks in the upwind finite volume approach have already been presented: reconstruction, flux evaluation, and evolution. By far, the most difficult task in this process is the reconstruction step.

The Basic Psychological Needs at Work Scale: Measurement Invariance between Canada and France.

PubMed

Brien, Maryse; Forest, Jacques; Mageau, Geneviève A; Boudrias, Jean-Sébastien; Desrumaux, Pascale; Brunet, Luc; Morin, Estelle M

2012-07-01

The purpose of this study is to develop and validate the Basic Psychological Needs at Work Scale (BPNWS) in French, but items are also provided in English in the article. The BPNWS is a work-related self-report instrument designed to measure the degree to which the needs for autonomy, competence, and relatedness, as identified by Self-Determination Theory (Deci & Ryan, 2000), are satisfied at work. Using exploratory and confirmatory factor analysis, the first study examines the structure of the BPNWS in a group of 271 workers. The second study tests the measurement invariance of the scale in a group of 851 teachers from two different cultures, Canada and France. Results support the three-factor structure and show adequate internal consistency, as well as nomological validity across samples. © 2012 The Authors. Applied Psychology: Health and Well-Being © 2012 The International Association of Applied Psychology.

Minimum Contradictions Physics and Propulsion via Superconducting Magnetic Field Trapping

NASA Astrophysics Data System (ADS)

Nassikas, A. A.

2010-01-01

All theories are based on Axioms which obviously are arbitrary; e.g. SRT, GRT, QM Axioms. Instead of manipulating the experience through a new set of Arbitrary Axioms it would be useful to search, through a basic tool that we have at our disposal i.e. Logic Analysis, for a set of privileged axioms. Physics theories, beyond their particular axioms, can be restated through the basic communication system as consisting of the Classical Logic, the Sufficient Reason Principle and the Anterior-Posterior Axiom. By means of a theorem this system can be proven as contradictory. The persistence in logic is the way for a set of privileged axioms to be found. This can be achieved on the basis of the Claim for Minimum Contradictions. Further axioms beyond the ones of the basic communications imply further contradictions. Thus, minimum contradictions can be achieved when things are described through anterior-posterior terms; due to existing contradictions through stochastic space-time, which is matter itself, described through a Ψ wave function and distributed, in a Hypothetical Measuring Field (HMF), through the density probability function P(r, t). On this basis, a space-time QM is obtained and this QM is a unified theory satisfying the requirements of quantum gravity. There are both mass-gravitational space-time (g) regarded as real and charge-electromagnetic (em) space-time that could be regarded as imaginary. In a closed system energy conversion-conservation and momentum action take place through photons, which can be regarded either as (g) or (em) space-time formation whose rest mass is equal to zero. Universe Evolution is described through the interaction of the gravitational (g) with the electromagnetic (em) space-time-matter field and not through any other entities. This methodology implies that there is no need for dark matter. An experiment is proposed relative to the (g)+(em) interaction based on Superconducting Magnetic Field Trapping to validate this approach.

Hazardous Asteroids: Cloaking STEM Skills Training within an Attention-Grabbing Science/Math Course

NASA Astrophysics Data System (ADS)

Ryan, Eileen V.; Ryan, William H.

2015-11-01

A graduate-level course was designed and taught during the summer months from 2009 - 2015 in order to contribute to the training and professional development of K-12 teachers residing in the Southwest. The teachers were seeking Master’s degrees via the New Mexico Institute of Mining and Technology’s (NMT’s) Masters of Science Teaching (MST) program, and the course satisfied a science or math requirement. The MST program provides opportunities for in-service teachers to enhance their content backgrounds in science, mathematics, engineering, and technology (SMET). The ultimate goal is to assist teachers in gaining knowledge that has direct application in the classroom.The engaging topic area of near-Earth object (NEO) characterization studies was used to create a fun and exciting framework for mastering basic skills and concepts in physics and astronomy. The objective was to offer a class that had the appropriate science rigor (with an emphasis on mathematics) within a non-threatening format. The course, entitled “Hazardous Asteroids”, incorporates a basic planetary physics curriculum, with challenging laboratories that include a heavy emphasis on math and technology. Since the authors run a NASA-funded NEO research and follow-up program, also folded into the course is the use of the Magdalena Ridge Observatory’s 2.4-meter telescope so participants can take and reduce their own data on a near-Earth asteroid.In exit assessments, the participants have given the course excellent ratings for design and implementation, and the overall degree of satisfaction was high. This validates that a well-constructed (and rigorous) course can be effective in receptively reaching teachers in need of basic skills refreshment. Many of the teachers taking the course were employed in school districts serving at-risk or under-prepared students, and the course helped provide them with the confidence vital to developing new strategies for successful teaching.

49 CFR 551.63 - May a foreign manufacturer submit a designation by email or facsimile?

Code of Federal Regulations, 2010 CFR

2010-10-01

... email or facsimile? 551.63 Section 551.63 Transportation Other Regulations Relating to Transportation... foreign manufacturer submit a designation by email or facsimile? No, the statute requires designation... designation documents submitted via email or facsimile, as they do not satisfy this requirement. ...

41 CFR 301-11.18 - What M&IE rate will I receive if a meal(s) is furnished by the Government or is included in the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... consume the furnished meal(s) because of medical requirements or religious beliefs; (2) In accordance with... (4) You purchase substitute meals in order to satisfy your medical requirements or religious beliefs...

41 CFR 301-11.18 - What M&IE rate will I receive if a meal(s) is furnished by the Government or is included in the...

Code of Federal Regulations, 2011 CFR

2011-07-01

... consume the furnished meal(s) because of medical requirements or religious beliefs; (2) In accordance with... (4) You purchase substitute meals in order to satisfy your medical requirements or religious beliefs...

50 CFR 23.25 - What additional information is required on a non-Party CITES document?

Code of Federal Regulations, 2013 CFR

2013-10-01

... IN ENDANGERED SPECIES OF WILD FAUNA AND FLORA (CITES) Prohibitions, Exemptions, and Requirements § 23... export will not be detrimental to the survival of the species.(ii) The Management Authority is satisfied... purposes that are not detrimental to the survival of the species. ...

50 CFR 23.25 - What additional information is required on a non-Party CITES document?

Code of Federal Regulations, 2011 CFR

2011-10-01

... IN ENDANGERED SPECIES OF WILD FAUNA AND FLORA (CITES) Prohibitions, Exemptions, and Requirements § 23... export will not be detrimental to the survival of the species.(ii) The Management Authority is satisfied... purposes that are not detrimental to the survival of the species. ...

50 CFR 23.25 - What additional information is required on a non-Party CITES document?

Code of Federal Regulations, 2012 CFR

2012-10-01

... IN ENDANGERED SPECIES OF WILD FAUNA AND FLORA (CITES) Prohibitions, Exemptions, and Requirements § 23... export will not be detrimental to the survival of the species.(ii) The Management Authority is satisfied... purposes that are not detrimental to the survival of the species. ...

49 CFR 192.913 - When may an operator deviate its program from certain requirements of this subpart?

Code of Federal Regulations, 2011 CFR

2011-10-01

... management program. An operator that uses a performance-based approach that satisfies the requirements for... to demonstrate the exceptional performance of its integrity management program through the following... to the operator's pipeline system and to the operator's integrity management program; (vi) A...