High-performance computing-based exploration of flow control with micro devices.

PubMed

Fujii, Kozo

2014-08-13

The dielectric barrier discharge (DBD) plasma actuator that controls flow separation is one of the promising technologies to realize energy savings and noise reduction of fluid dynamic systems. However, the mechanism for controlling flow separation is not clearly defined, and this lack of knowledge prevents practical use of this technology. Therefore, large-scale computations for the study of the DBD plasma actuator have been conducted using the Japanese Petaflops supercomputer 'K' for three different Reynolds numbers. Numbers of new findings on the control of flow separation by the DBD plasma actuator have been obtained from the simulations, and some of them are presented in this study. Knowledge of suitable device parameters is also obtained. The DBD plasma actuator is clearly shown to be very effective for controlling flow separation at a Reynolds number of around 10(5), and several times larger lift-to-drag ratio can be achieved at higher angles of attack after stall. For higher Reynolds numbers, separated flow is partially controlled. Flow analysis shows key features towards better control. DBD plasma actuators are a promising technology, which could reduce fuel consumption and contribute to a green environment by achieving high aerodynamic performance. The knowledge described above can be obtained only with high-end computers such as the supercomputer 'K'. © 2014 The Author(s) Published by the Royal Society. All rights reserved.

Progress in Payload Separation Risk Mitigation for a Deployable Venus Heat Shield

NASA Technical Reports Server (NTRS)

Smith, Brandon P.; Yount, Bryan C.; Venkatapathy, Ethiraj; Stern, Eric C.; Prabhu, Dinesh K.; Litton, Daniel K.

2013-01-01

A deployable decelerator known as the Adaptive Deployable Entry and Placement Technology (ADEPT) offers substantial science and mass savings for the Venus In Situ Explorer (VISE) mission. The lander and science payload must be separated from ADEPT during atmospheric entry. This paper presents a trade study of the separation system concept of operations and provides a conceptual design of the baseline: aft-separation with a subsonic parachute. Viability of the separation system depends on the vehicle's dynamic stability characteristics during deceleration from supersonic to subsonic speeds. A trajectory sensitivity study presented shows that pitch damping and Venusian winds drive stability prior to parachute deployment, while entry spin rate is not a driver of stability below Mach 5. Additionally, progress in free-flight CFD techniques capable of computing aerodynamic damping parameters is presented. Exploratory simulations of ADEPT at a constant speed of Mach number of 0.8 suggest the vehicle may have an oscillation limit cycle near 5 angle-of-attack. The proposed separation system conceptual design is thought to be viable.

Common Low-cost IM Explosive Program. Development of Next Generation Insensitive Munitions: A Success Story

DTIC Science & Technology

2011-11-30

fuze separating from the shell body preventing high order detonations thus saving the lives of the Soldiers. Unit’s SPC Alan Ng  with his father Peter...Sensitive If not fully compliant, must show improvement over Baseline explosive Affordable Artillery Cost Drivers = Steel Body Material & Explosive Fill...Mortar Cost Drivers = Steel Body Material, Fuze & Propelling Charges Producible within the National Technology and Industrial Base Infrastructure

The Impact of Sustainable Development Technology on a Small Economy-The Case of Energy-Saving Technology.

PubMed

Chen, Xiding; Huang, Qinghua; Huang, Weilun; Li, Xue

2018-02-08

We investigated the impact of a sustainable development technology on the macroeconomic variables in a small economy utilizing a case study with a stochastically improving energy saving technology and a stochastically increasing energy price. The results show the technological displacement effects of energy saving technology are stronger, but there are more ambiguous instantaneous returns to physical capital. However, the energy saving technology's displacement effects might not affect the conditions under which the Harberger-Laursen-Metzler (HLM) effect holds. The effects of rising energy prices on bonds are stronger, and there are more ambiguous instantaneous returns, but the conditions under which the HLM effect holds are different.

Electric energy savings from new technologies. Revision 1

DOE Office of Scientific and Technical Information (OSTI.GOV)

Harrer, B.J.; Kellogg, M.A.; Lyke, A.J.

1986-09-01

Purpose of the report is to provide information about the electricity-saving potential of new technologies to OCEP that it can use in developing alternative long-term projections of US electricity consumption. Low-, base-, and high-case scenarios of the electricity savings for 10 technologies were prepared. The total projected annual savings for the year 2000 for all 10 technologies were 137 billion kilowatt hours (BkWh), 279 BkWh, and 470 BkWh, respectively, for the three cases. The magnitude of these savings projections can be gauged by comparing them to the Department's reference case projection for the 1985 National Energy Policy Plan. In themore » Department's reference case, total consumption in 2000 is projected to be 3319 BkWh. Because approximately 75% of the base-case estimate of savings are already incorporated into the reference projection, only 25% of the savings estimated here should be subtracted from the reference projection for analysis purposes.« less

The Impact of Sustainable Development Technology on a Small Economy—The Case of Energy-Saving Technology

PubMed Central

Huang, Qinghua; Huang, Weilun; Li, Xue

2018-01-01

We investigated the impact of a sustainable development technology on the macroeconomic variables in a small economy utilizing a case study with a stochastically improving energy saving technology and a stochastically increasing energy price. The results show the technological displacement effects of energy saving technology are stronger, but there are more ambiguous instantaneous returns to physical capital. However, the energy saving technology’s displacement effects might not affect the conditions under which the Harberger-Laursen-Metzler (HLM) effect holds. The effects of rising energy prices on bonds are stronger, and there are more ambiguous instantaneous returns, but the conditions under which the HLM effect holds are different. PMID:29419788

Environmental burdens in the management of end-of-life cathode ray tubes.

PubMed

Rocchetti, Laura; Beolchini, Francesca

2014-02-01

We compared the environmental burdens in the management of end-of life cathode ray tubes (CRTs) within two frameworks according to the different technologies of the production of televisions/monitors. In the first case, CRT recycling is addressed to the recovery of the panel and funnel glass for the manufacturing of new CRT screens. In the second case, where flat screen technology has replaced that of CRT, the recycling is addressed to the recovery of the glass cullet and lead for other applications. The impacts were evaluated according to the problem-oriented methodology of the Institute of Environmental Sciences, Leiden University, Leiden, The Netherlands. Our data confirm that in both cases, the recycling treatment allows benefits to be gained for the environment through the recovery of the secondary raw materials. These benefits are higher for the "CRT technology" framework (1 kg CO2 saved per CRT) than for the "flat screen technology" (0.9 kg CO2 saved, per CRT, as the highest possible), mainly due to the high energy consumption for lead separation from the funnel glass. Furthermore, the recovery of yttrium from the fluorescent powders that are a residue of the recycling treatment would further improve the CO2 credit for both the frameworks considered, which would provide a further saving of about 0.75 kg CO2 per CRT, net of the energy and raw materials needed for the recovery. Overall, this study confirms that, even with a change in the destination of the recovered materials, the recycling processes provide a benefit for the environment: indeed the higher loads for the environment are balanced by avoiding the primary production of the recovered materials. Copyright © 2013 Elsevier Ltd. All rights reserved.

78 FR 18585 - Energy Technology Savings LLC; Supplemental Notice That Initial Market-Based Rate Filing Includes...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-27

... facilitate electronic service, persons with Internet access who will eFile a document and/or be listed as a... Technology Savings LLC; Supplemental Notice That Initial Market-Based Rate Filing Includes Request for... Energy Technology Savings LLC's application for market-based rate authority, with an accompanying rate...

An assessment of the benefits of the use of NASA developed fuel conservative technology in the US commercial aircraft fleet

NASA Technical Reports Server (NTRS)

1975-01-01

Cost and benefits of a fuel conservative aircraft technology program proposed by NASA are estimated. NASA defined six separate technology elements for the proposed program: (a) engine component improvement (b) composite structures (c) turboprops (d) laminar flow control (e) fuel conservative engine and (f) fuel conservative transport. There were two levels postulated: The baseline program was estimated to cost $490 million over 10 years with peak funding in 1980. The level two program was estimated to cost an additional $180 million also over 10 years. Discussions with NASA and with representatives of the major commercial airframe manufacturers were held to estimate the combinations of the technology elements most likely to be implemented, the potential fuel savings from each combination, and reasonable dates for incorporation of these new aircraft into the fleet.

Energy-Saving Opportunities for Manufacturing Enterprises (International English Fact Sheet)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

This fact sheet provides information about the Industrial Technologies Program Save Energy Now energy audit process, software tools, training, energy management standards, and energy efficient technologies to help U.S. companies identify energy cost savings.

Reducing Operating Costs and Energy Consumption at Water Utilities

EPA Pesticide Factsheets

Due to their unique combination of high energy usage and potential for significant savings, utilities are turning to energy-efficient technologies to help save money. Learn about cost and energy saving technologies from this brochure.

Quantifying Adoption Rates and Energy Savings Over Time for Advanced Manufacturing Technologies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hanes, Rebecca; Carpenter Petri, Alberta C; Riddle, Matt

Energy-efficient manufacturing technologies can reduce energy consumption and lower operating costs for an individual manufacturing facility, but increased process complexity and the resulting risk of disruption means that manufacturers may be reluctant to adopt such technologies. In order to quantify potential energy savings at scales larger than a single facility, it is necessary to account for how quickly and how widely the technology will be adopted by manufacturers. This work develops a methodology for estimating energy-efficient manufacturing technology adoption rates using quantitative, objectively measurable technology characteristics, including energetic, economic and technical criteria. Twelve technology characteristics are considered, and each characteristicmore » is assigned an importance weight that reflects its impact on the overall technology adoption rate. Technology characteristic data and importance weights are used to calculate the adoption score, a number between 0 and 1 that represents how quickly the technology is likely to be adopted. The adoption score is then used to estimate parameters for the Bass diffusion curve, which quantifies the change in the number of new technology adopters in a population over time. Finally, energy savings at the sector level are calculated over time by multiplying the number of new technology adopters at each time step with the technology's facility-level energy savings. The proposed methodology will be applied to five state-of-the-art energy-efficient technologies in the carbon fiber composites sector, with technology data obtained from the Department of Energy's 2016 bandwidth study. Because the importance weights used in estimating the Bass curve parameters are subjective, a sensitivity analysis will be performed on the weights to obtain a range of parameters for each technology. The potential energy savings for each technology and the rate at which each technology is adopted in the sector are quantified and used to identify the technologies which offer the greatest cumulative sector-level energy savings over a period of 20 years. Preliminary analysis indicates that relatively simple technologies, such as efficient furnaces, will be adopted more quickly and result in greater cumulative energy savings compared to more complex technologies that require process retrofitting, such as advanced control systems.« less

New technology and energy-saving equipment for production of composite materials

NASA Astrophysics Data System (ADS)

Romanovich, A. A.; Glagolev, S. N.; Babaevsky, A. N.

2018-03-01

The article considers industrial technology and energy-saving equipment for cement and composite binder production with a reduction in energy intensity of the process up to 50% due to the synergetic effect during mechanic activation of the raw mix with the replacement of part of the clinker component with the mineral hydro-active additive. The technological process is based on the sequential introduction of components in dispersed phases into the feed mixture in the grinding path and at the stage of product separation with certain dispersed characteristics. The increase in the energy efficiency of the line is achieved by the joint operation of the press roller aggregate, which is the development of BSTU named after V.G. Shoukhov, and rotor-vortex mills of a very fine grinding of a new design. The experienced design of the aggregate with the device for deagglomeration of the pressed tape allows combining the processes of grinding and disaggregation of the pressed material, thereby reducing the operating costs and increasing the efficiency of using the grinding unit. Comparative tests of cement samples obtained in energy-saving aggregates (PRA + RVM) are given which allowed establishing that their beam strength for compression and bending is higher by 15-20% than the traditional method obtained in a ball mill. An analytical expression is also given that allows one to determine the power consumed for the deagglomeration of crushed and pressed material between the main rolls, taking into account the geometric dimensions of the rolls and the physico-mechanical characteristics of the material.

Review of the Application of Green Building and Energy Saving Technology

NASA Astrophysics Data System (ADS)

Tong, Zhineng

2017-12-01

The use of energy-saving technologies in green buildings should run through the entire process of building design, construction and use, enabling green energy-saving technologies to maximize their effectiveness in construction. Realize the sustainable development of green building, reduce energy consumption, reduce people’s interference with the natural environment, suitable for people living in “green” building.

Beads-on-String Structured Nanofibers for Smart and Reversible Oil/Water Separation with Outstanding Antifouling Property.

PubMed

Wang, Yuanfeng; Lai, Chuilin; Wang, Xiaowen; Liu, Yang; Hu, Huawen; Guo, Yujuan; Ma, Kaikai; Fei, Bin; Xin, John H

2016-09-28

It is challenging to explore a unified solution for the treatment of oily wastewater from complex sources. Thus, membrane materials with flexible separation schemes are highly desired. Herein, we fabricated a smart membrane by electrospinning TiO2 doped polyvinylidene fluoride (PVDF) nanofibers. The as-formed beads-on-string structure and hierarchical roughness of the nanofibers contribute to its superwetting/resisting property to liquids, which is desirable in oil/water separation. Switched simply by UV (or sunlight) irradiation and heating treatment, the smart membrane can realize reversible separation of oil/water mixtures by selectively allowing water or oil to pass through alone. Most importantly, the as-prepared nanofiber membrane possesses outstanding antifouling and self-cleaning performance resulting from the photocatalytic property of TiO2, which has practical significance in saving solvents and recycling materials. This work provides a route for fabricating cost-effective, easily scaled up, and recyclable membranes for on-demand oil/water separation in versatile situations, which can be of great usage in the new green separation technology.

Anaerobic treatment as a core technology for energy, nutrients and water recovery from source-separated domestic waste(water).

PubMed

Zeeman, Grietje; Kujawa, Katarzyna; de Mes, Titia; Hernandez, Lucia; de Graaff, Marthe; Abu-Ghunmi, Lina; Mels, Adriaan; Meulman, Brendo; Temmink, Hardy; Buisman, Cees; van Lier, Jules; Lettinga, Gatze

2008-01-01

Based on results of pilot scale research with source-separated black water (BW) and grey water (GW), a new sanitation concept is proposed. BW and GW are both treated in a UASB (-septic tank) for recovery of CH4 gas. Kitchen waste is added to the anaerobic BW treatment for doubling the biogas production. Post-treatment of the effluent is providing recovery of phosphorus and removal of remaining COD and nitrogen. The total energy saving of the new sanitation concept amounts to 200 MJ/year in comparison with conventional sanitation, moreover 0.14 kg P/p/year and 90 litres of potential reusable water are produced. (c) IWA Publishing 2008.

Conducting polymers: Synthesis and industrial applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gottesfeld, S.

1997-04-01

The Conducting Polymer project funded by the AIM Program has developed new methods for the synthesis of conducting polymers and evaluated new industrial applications for these materials which will result in significant reductions in energy usage or industrial waste. The applications specifically addressed during FY 1996 included two ongoing efforts on membranes for gas separation and on electrochemical capacitors and a third new application: electrochemical reactors (ECRs) based on polymeric electrolytes. As a gas separation membrane, conducting polymers offer high selectivity and the potential to chemically or electrically adapt the membrane for specific gas combinations. Potential energy savings in themore » US for this application are estimated at 1 to 3 quads/yr. As an active material in electrochemical capacitors, electronically conducting polymers have the potential of storing large amounts of electric energy in low cost materials. Potential energy savings estimated at 1 quad/yr would result from introduction of electrochemical capacitors as energy storage devices in power trains of electric and hybrid vehicles, once such vehicles reach 20% of the total transportation market in the US. In the chlor-alkali industry, electrochemical reactors based on polymer electrolyte membranes consume around 1 % of the total electric power in the US. A new activity, started in FY 1996, is devoted to energy efficient ECRs. In the case of the chlor-alkali industry, energy savings as high as 50% seem possible with the novel ECR technology demonstrated by the author in 1996.« less

Sorbent-based Oxygen Production for Energy Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sethi, Vijay

Project DE-FE0024075 deals with the development of a moderate-temperature sorbent-based oxygen production technology. Sorbent-based oxygen production process utilizes oxygen-storage properties of Perovskites to (1) adsorb oxygen from air in a solid sorbent, and (2) release the adsorbed oxygen into a sweep gas such as CO 2 and/or steam for gasification systems or recycled flue gas for oxy-combustion systems. Pure oxygen can be produced by the use of vacuum instead of a sweep gas to affect the pressure swing. By developing more efficient and stable, higher sorption capacity, newer class of materials operating at moderate temperatures this process represents a majormore » advancement in air separation technology. Newly developed perovskite ceramic sorbent materials with order-disorder transition have a higher O 2 adsorption capacity, potentially 200 °C lower operating temperatures, and up to two orders of magnitude faster desorption rates than those used in earlier development efforts. The performance advancements afforded by the new materials lead to substantial savings in capital investment and operational costs. Cost of producing oxygen using sorbents could be as much as 26% lower than VPSA and about 13% lower than a large cryogenic air separation unit. Cost advantage against large cryogenic separation is limited because sorbent-based separation numbers up sorbent modules for achieving the larger capacity.« less

Prospects for reducing the processing cost of lithium ion batteries

DOE PAGES

Wood III, David L.; Li, Jianlin; Daniel, Claus

2014-11-06

A detailed processing cost breakdown is given for lithium-ion battery (LIB) electrodes, which focuses on: elimination of toxic, costly N-methylpyrrolidone (NMP) dispersion chemistry; doubling the thicknesses of the anode and cathode to raise energy density; and, reduction of the anode electrolyte wetting and SEI-layer formation time. These processing cost reduction technologies generically adaptable to any anode or cathode cell chemistry and are being implemented at ORNL. This paper shows step by step how these cost savings can be realized in existing or new LIB manufacturing plants using a baseline case of thin (power) electrodes produced with NMP processing and amore » standard 10-14-day wetting and formation process. In particular, it is shown that aqueous electrode processing can cut the electrode processing cost and energy consumption by an order of magnitude. Doubling the thickness of the electrodes allows for using half of the inactive current collectors and separators, contributing even further to the processing cost savings. Finally wetting and SEI-layer formation cost savings are discussed in the context of a protocol with significantly reduced time. These three benefits collectively offer the possibility of reducing LIB pack cost from $502.8 kWh-1-usable to $370.3 kWh-1-usable, a savings of $132.5/kWh (or 26.4%).« less

76 FR 6653 - Public Housing Capital Fund Program

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-07

...; heating system replacements; wall insulation; site-based generation; advanced energy savings technologies...; wall insulation; site-based generation; advanced energy savings technologies, including renewable...

Design and Implementation of Green Construction Scheme for a High-rise Residential Building Project

NASA Astrophysics Data System (ADS)

Zhou, Yong; Huang, You Zhen

2018-06-01

This paper mainly studies the green construction scheme of a high-rise residential building project. From "four sections one environmental protection", saving material, water saving, energy saving, economical use of land and environmental protection conduct analysis and research. Adopting scientific, advanced, reasonable and economical construction technology measures, implementing green construction method. Promoting energy-saving technologies in buildings, ensuring the sustainable use of resources, Maximum savings of resources and energy, increase energy efficiency, to reduce pollution, reducing the adverse environmental impact of construction activities, ensure construction safety, build sustainable buildings.

Cogeneration Technology Alternatives Study (CTAS). Volume 3: Industrial processes

NASA Technical Reports Server (NTRS)

Palmer, W. B.; Gerlaugh, H. E.; Priestley, R. R.

1980-01-01

Cogenerating electric power and process heat in single energy conversion systems rather than separately in utility plants and in process boilers is examined in terms of cost savings. The use of various advanced energy conversion systems are examined and compared with each other and with current technology systems for their savings in fuel energy, costs, and emissions in individual plants and on a national level. About fifty industrial processes from the target energy consuming sectors were used as a basis for matching a similar number of energy conversion systems that are considered as candidate which can be made available by the 1985 to 2000 time period. The sectors considered included food, textiles, lumber, paper, chemicals, petroleum, glass, and primary metals. The energy conversion systems included steam and gas turbines, diesels, thermionics, stirling, closed cycle and steam injected gas turbines, and fuel cells. Fuels considered were coal, both coal and petroleum based residual and distillate liquid fuels, and low Btu gas obtained through the on site gasification of coal. An attempt was made to use consistent assumptions and a consistent set of ground rules specified by NASA for determining performance and cost. Data and narrative descriptions of the industrial processes are given.

Environmentally-friendly oxygen-free roasting/wet magnetic separation technology for in situ recycling cobalt, lithium carbonate and graphite from spent LiCoO2/graphite lithium batteries.

PubMed

Li, Jia; Wang, Guangxu; Xu, Zhenming

2016-01-25

The definite aim of the present paper is to present some novel methods that use oxygen-free roasting and wet magnetic separation to in situ recycle of cobalt, Lithium Carbonate and Graphite from mixed electrode materials. The in situ recycling means to change waste into resources by its own components, which is an idea of "waste+waste→resources." After mechanical scraping the mixed electrode materials enrich powders of LiCoO2 and graphite. The possible reaction between LiCoO2 and graphite was obtained by thermodynamic analysis. The feasibility of the reaction at high temperature was studied with the simultaneous thermogravimetry analysis under standard atmospheric pressure. Then the oxygen-free roasting/wet magnetic separation method was used to transfer the low added value mixed electrode materials to high added value products. The results indicated that, through the serious technologies of oxygen-free roasting and wet magnetic separation, mixture materials consist with LiCoO2 and graphite powders are transferred to the individual products of cobalt, Lithium Carbonate and Graphite. Because there is not any chemical solution added in the process, the cost of treating secondary pollution can be saved. This study provides a theoretical basis for industrial-scale recycling resources from spent LIBs. Copyright © 2015 Elsevier B.V. All rights reserved.

Benefits of information technology-enabled diabetes management.

PubMed

Bu, Davis; Pan, Eric; Walker, Janice; Adler-Milstein, Julia; Kendrick, David; Hook, Julie M; Cusack, Caitlin M; Bates, David W; Middleton, Blackford

2007-05-01

To determine the financial and clinical benefits of implementing information technology (IT)-enabled disease management systems. A computer model was created to project the impact of IT-enabled disease management on care processes, clinical outcomes, and medical costs for patients with type 2 diabetes aged >25 years in the U.S. Several ITs were modeled (e.g., diabetes registries, computerized decision support, remote monitoring, patient self-management systems, and payer-based systems). Estimates of care process improvements were derived from published literature. Simulations projected outcomes for both payer and provider organizations, scaled to the national level. The primary outcome was medical cost savings, in 2004 U.S. dollars discounted at 5%. Secondary measures include reduction of cardiovascular, cerebrovascular, neuropathy, nephropathy, and retinopathy clinical outcomes. All forms of IT-enabled disease management improved the health of patients with diabetes and reduced health care expenditures. Over 10 years, diabetes registries saved $14.5 billion, computerized decision support saved $10.7 billion, payer-centered technologies saved $7.10 billion, remote monitoring saved $326 million, self-management saved $285 million, and integrated provider-patient systems saved $16.9 billion. IT-enabled diabetes management has the potential to improve care processes, delay diabetes complications, and save health care dollars. Of existing systems, provider-centered technologies such as diabetes registries currently show the most potential for benefit. Fully integrated provider-patient systems would have even greater potential for benefit. These benefits must be weighed against the implementation costs.

Energy Saving Melting and Revert Reduction Technology (Energy SMARRT): Manufacturing Advanced Engineered Components Using Lost Foam Casting Technology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Littleton, Harry; Griffin, John

2011-07-31

This project was a subtask of Energy Saving Melting and Revert Reduction Technology (Energy SMARRT) Program. Through this project, technologies, such as computer modeling, pattern quality control, casting quality control and marketing tools, were developed to advance the Lost Foam Casting process application and provide greater energy savings. These technologies have improved (1) production efficiency, (2) mechanical properties, and (3) marketability of lost foam castings. All three reduce energy consumption in the metals casting industry. This report summarizes the work done on all tasks in the period of January 1, 2004 through June 30, 2011. Current (2011) annual energy savingmore » estimates based on commercial introduction in 2011 and a market penetration of 97% by 2020 is 5.02 trillion BTU's/year and 6.46 trillion BTU's/year with 100% market penetration by 2023. Along with these energy savings, reduction of scrap and improvement in casting yield will result in a reduction of the environmental emissions associated with the melting and pouring of the metal which will be saved as a result of this technology. The average annual estimate of CO2 reduction per year through 2020 is 0.03 Million Metric Tons of Carbon Equivalent (MM TCE).« less

Integrated control of emission reductions, energy-saving, and cost-benefit using a multi-objective optimization technique in the pulp and paper industry.

PubMed

Wen, Zongguo; Xu, Chang; Zhang, Xueying

2015-03-17

Reduction of water pollutant emissions and energy consumption is regarded as a key environmental objective for the pulp and paper industry. The paper develops a bottom-up model called the Industrial Water Pollutant Control and Technology Policy (IWPCTP) based on an industrial technology simulation system and multiconstraint technological optimization. Five policy scenarios covering the business as usual (BAU) scenario, the structural adjustment (SA) scenario, the cleaner technology promotion (CT) scenario, the end-treatment of pollutants (EOP) scenario, and the coupling measures (CM) scenario have been set to describe future policy measures related to the development of the pulp and paper industry from 2010-2020. The outcome of this study indicates that the energy saving amount under the CT scenario is the largest, while that under the SA scenario is the smallest. Under the CT scenario, savings by 2020 include 70 kt/year of chemical oxygen demand (COD) emission reductions and savings of 7443 kt of standard coal, 539.7 ton/year of ammonia nitrogen (NH4-N) emission reductions, and savings of 7444 kt of standard coal. Taking emission reductions, energy savings, and cost-benefit into consideration, cleaner technologies like highly efficient pulp washing, dry and wet feedstock preparation, and horizontal continuous cooking, medium and high consistency pulping and wood dry feedstock preparation are recommended.

Decision support for redesigning wastewater treatment technologies.

PubMed

McConville, Jennifer R; Künzle, Rahel; Messmer, Ulrike; Udert, Kai M; Larsen, Tove A

2014-10-21

This paper offers a methodology for structuring the design space for innovative process engineering technology development. The methodology is exemplified in the evaluation of a wide variety of treatment technologies for source-separated domestic wastewater within the scope of the Reinvent the Toilet Challenge. It offers a methodology for narrowing down the decision-making field based on a strict interpretation of treatment objectives for undiluted urine and dry feces and macroenvironmental factors (STEEPLED analysis) which influence decision criteria. Such an evaluation identifies promising paths for technology development such as focusing on space-saving processes or the need for more innovation in low-cost, energy-efficient urine treatment methods. Critical macroenvironmental factors, such as housing density, transportation infrastructure, and climate conditions were found to affect technology decisions regarding reactor volume, weight of outputs, energy consumption, atmospheric emissions, investment cost, and net revenue. The analysis also identified a number of qualitative factors that should be carefully weighed when pursuing technology development; such as availability of O&M resources, health and safety goals, and other ethical issues. Use of this methodology allows for coevolution of innovative technology within context constraints; however, for full-scale technology choices in the field, only very mature technologies can be evaluated.

Performance of Nanocomposite Membranes Containing 0D to 2D Nanofillers for CO₂ Separation: A Review.

PubMed

Janakiram, Saravanan; Ahmadi, Mahdi; Dai, Zhongde; Ansaloni, Luca; Deng, Liyuan

2018-05-14

Membrane technology has the potential to be an eco-friendly and energy-saving solution for the separation of CO₂ from different gaseous streams due to the lower cost and the superior manufacturing features. However, the performances of membranes made of conventional polymers are limited by the trade-off between the permeability and selectivity. Improving the membrane performance through the addition of nanofillers within the polymer matrix offers a promising strategy to achieve superior separation performance. This review aims at providing a complete overview of the recent advances in nanocomposite membranes for enhanced CO₂ separation. Nanofillers of various dimensions and properties are categorized and effects of nature and morphology of the 0D to 2D nanofillers in the corresponding nanocomposite membranes of different polymeric matrixes are discussed with regard to the CO₂ permeation properties. Moreover, a comprehensive summary of the performance data of various nanocomposite membranes is presented. Finally, the advantages and challenges of various nanocomposite membranes are discussed and the future research and development opportunities are proposed.

2011 Naval Energy Forum. Volume 2

DTIC Science & Technology

2011-10-14

APPLIED RESEARCH ASSOCIATES • CHASE SUPPLY, INC. • ESPEY MGF. & ELECTRONICS • FREE FLOW POWER • LIVEFUELS • MILSPRAY MILITARY TECHNOLOGIES • PETRA ... Martin Luther King experts reality check? 5 “Heavier-than-air flying machines are impossible” - Lord Kelvin, President, Royal Society, 1895 6 “The...1. Win-Win: Mutual Benefit & Value Proposition – DOD: Save Energy, Save Money, Save Lives (General Martin Dempsey) – DOE: Accelerate technology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Desroches, Louis-Benoit; Garbesi, Karina

It is well established that energy efficiency is most often the lowest cost approach to reducing national energy use and minimizing carbon emissions. National investments in energy efficiency to date have been highly cost-effective. The cumulative impacts (out to 2050) of residential energy efficiency standards are expected to have a benefit-to-cost ratio of 2.71:1. This project examined energy end-uses in the residential, commercial, and in some cases the industrial sectors. The scope is limited to appliances and equipment, and does not include building materials, building envelopes, and system designs. This scope is consistent with the scope of DOE's appliance standardsmore » program, although many products considered here are not currently subject to energy efficiency standards. How much energy could the United States save if the most efficient design options currently feasible were adopted universally? What design features could produce those savings? How would the savings from various technologies compare? With an eye toward identifying promising candidates and strategies for potential energy efficiency standards, the Max Tech and Beyond project aims to answer these questions. The analysis attempts to consolidate, in one document, the energy savings potential and design characteristics of best-on-market products, best-engineered products (i.e., hypothetical products produced using best-on-market components and technologies), and emerging technologies in research & development. As defined here, emerging technologies are fundamentally new and are as yet unproven in the market, although laboratory studies and/or emerging niche applications offer persuasive evidence of major energy-savings potential. The term 'max tech' is used to describe both best-engineered and emerging technologies (whichever appears to offer larger savings). Few best-on-market products currently qualify as max tech, since few apply all available best practices and components. The three primary analyses presented in this report are: Nevertheless, it is important to analyze best-on-market products, since data on truly max tech technologies are limited. (1) an analysis of the cross-cutting strategies most promising for reducing appliance and equipment energy use in the U.S.; (2) a macro-analysis of the U.S. energy-saving potential inherent in promising ultra-efficient appliance technologies; and (3) a product-level analysis of the energy-saving potential.« less

Smart Money

ERIC Educational Resources Information Center

Ullman, Ellen

2009-01-01

From using virtualization technology to accepting lunch payments online, school districts are seeking money-saving methods. In this article, the author discusses some methods used by school districts that allow them to save money from using virtualization technology to accepting lunch payments online.

Energy Efficient Engine Program: Technology Benefit/Cost Study, Volume II

NASA Technical Reports Server (NTRS)

Gray, D. E.; Gardner, W. B.

1983-01-01

The Benefit/Cost Study portion of the NASA-sponsored Energy Efficient Engine Component Development and Integration program was successful in achieving its objectives: identification of air transport propulsion system technology requirements for the years 2000 and 2010, and formulation of programs for developing these technologies. It is projected that the advanced technologies identified, when developed to a state of readiness, will provide future commercial and military turbofan engines with significant savings in fuel consumption and related operating costs. These benefits are significant and far from exhausted. The potential savings translate into billions of dollars in annual savings for the airlines. Analyses indicate that a significant portion of the overall savings is attributed to aerodynamic and structure advancements. Another important consideration in acquiring these benefits is developing a viable reference technology base that will permit engines to operate at substantially higher overall pressure ratios and bypass ratios. Results have pointed the direction for future research and a comprehensive program plan for achieving this was formulated. The next major step is initiating the program effort that will convert the advanced technologies into the expected benefits.

Save Energy Now Assessments Results 2008 Summary Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wright, Anthony L; Martin, Michaela A; Nimbalkar, Sachin U

In October 2005, U.S. Department of Energy Secretary Bodman launched his Easy Ways to Save Energy campaign with a promise to provide energy assessments to 200 of the largest U.S. manufacturing plants. DOE's Industrial Technologies Program (ITP) responded to the Secretary's campaign with its Save Energy Now initiative, featuring a new and highly cost-effective form of energy savings assessment. The approach for these assessments drew heavily on the existing resources of ITP's technology delivery component. Over the years, ITP Technology Delivery has worked with industry partners to assemble a suite of respected software tools, proven assessment protocols, training curricula, certified energy experts, and strong partnerships for deployment. The Save Energy Now assessments conducted in calendar year 2006 focused on natural gas savings and targeted many of the nation's largest manufacturing plants - those that consume at least 1 TBtu of energy annually. The 2006 Save Energy Now assessments focused primarily on assessments of steam and process heating systems, which account for an estimated 74% of all natural gas use by U.S. manufacturing plants. Because of the success of the Save Energy Now assessments conducted in 2006 and 2007, the program was expanded and enhanced in two major ways in 2008: (1) a new goal was set to perform at least 260 assessments; and (2) the assessment focus was expanded to include pumping, compressed air, and fan systems in addition to steam and process heating. DOE ITP also has developed software tools to assess energy efficiency improvement opportunities in pumping, compressed air, and fan systems. The Save Energy Now assessments integrate a strong training component designed to teach industrial plant personnel how to use DOE's opportunity assessment software tools. This approach has the advantages of promoting strong buy-in of plant personnel for the assessment and its outcomes and preparing them better to independently replicate the assessment process at the company's other facilities. Another important element of the Save Energy Now assessment process is the follow-up process used to identify how many of the recommended savings opportunities from individual assessments have been implemented in the industrial plants. Plant personnel involved with the Save Energy Now assessments are contacted 6 months, 12 months, and 24 months after individual assessments are completed to determine implementation results. A total of 260 Save Energy Now assessments were successfully completed in calendar year 2008. This means that a total of 718 assessments were completed in 2006, 2007, and 2008. As of July 2009, we have received a total of 239 summary reports from the ESAs that were conducted in year 2008. Hence, at the time that this report was prepared, 680 final assessment reports were completed (200 from year 2006, 241 from year 2007, and 239 from year 2008). The total identified potential cost savings from these 680 assessments ismore » $$1.1 billion per year, including natural gas savings of about 98 TBtu per year. These results, if fully implemented, could reduce CO{sub 2} emissions by about 8.9 million metric tons annually. When this report was prepared, data on implementation of recommended energy and cost savings measures from 488 Save Energy Now assessments were available. For these 488 plants, measures saving a total of $$147 million per year have been implemented, measures that will save $169 million per year are in the process of being implemented, and plants are planning implementation of measures that will save another $239 million per year. The implemented recommendations are already achieving total CO{sub 2} reductions of about 1.8 million metric tons per year. This report provides a summary of the key results for the Save Energy Now assessments completed in 2008; details of the 6-month, 12-month, and 24-month implementation results obtained to date; and an evaluation of these implementation results. This report also summarizes key accomplishments, findings, and lessons learned from all the Save Energy Now assessments completed to date. A separate report (Wright et al. 2010) provides more detailed information on key results for all of the 2008 assessments of steam, process heating, pumping, compressed air, and fan systems. Two prior reports (Wright et al. 2007 and Wright et al. 2009) detail the results from the 2006 and 2007 assessments and discuss the major components of the assessment process and improvements in the process made in 2007.« less

Save Energy Now Assessments Results 2008 Detailed Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wright, Anthony L; Martin, Michaela A; Nimbalkar, Sachin U

In October 2005, U.S. Department of Energy Secretary Bodman launched his Easy Ways to Save Energy campaign with a promise to provide energy assessments to 200 of the largest U.S. manufacturing plants. DOE's Industrial Technologies Program (ITP) responded to the Secretary's campaign with its Save Energy Now initiative, featuring a new and highly cost-effective form of energy savings assessment. The approach for these assessments drew heavily on the existing resources of ITP's technology delivery component. Over the years, ITP Technology Delivery has worked with industry partners to assemble a suite of respected software tools, proven assessment protocols, training curricula, certified energy experts, and strong partnerships for deployment. The Save Energy Now assessments conducted in calendar year 2006 focused on natural gas savings and targeted many of the nation's largest manufacturing plants - those that consume at least 1 TBtu of energy annually. The 2006 Save Energy Now assessments focused primarily on assessments of steam and process heating systems, which account for an estimated 74% of all natural gas use by U.S. manufacturing plants. Because of the success of the Save Energy Now assessments conducted in 2006 and 2007, the program was expanded and enhanced in two major ways in 2008: (1) a new goal was set to perform at least 260 assessments; and (2) the assessment focus was expanded to include pumping, compressed air, and fan systems in addition to steam and process heating. DOE ITP also has developed software tools to assess energy efficiency improvement opportunities in pumping, compressed air, and fan systems. The Save Energy Now assessments integrate a strong training component designed to teach industrial plant personnel how to use DOE's opportunity assessment software tools. This approach has the advantages of promoting strong buy-in of plant personnel for the assessment and its outcomes and preparing them better to independently replicate the assessment process at the company's other facilities. Another important element of the Save Energy Now assessment process is the follow-up process used to identify how many of the recommended savings opportunities from individual assessments have been implemented in the industrial plants. Plant personnel involved with the Save Energy Now assessments are contacted 6 months, 12 months, and 24 months after individual assessments are completed to determine implementation results. A total of 260 Save Energy Now assessments were successfully completed in calendar year 2008. This means that a total of 718 assessments were completed in 2006, 2007, and 2008. As of July 2009, we have received a total of 239 summary reports from the ESAs that were conducted in year 2008. Hence, at the time that this report was prepared, 680 final assessment reports were completed (200 from year 2006, 241 from year 2007, and 239 from year 2008). The total identified potential cost savings from these 680 assessments ismore » $$1.1 billion per year, including natural gas savings of about 98 TBtu per year. These results, if fully implemented, could reduce CO{sub 2} emissions by about 8.9 million metric tons annually. When this report was prepared, data on implementation of recommended energy and cost savings measures from 488 Save Energy Now assessments were available. For these 488 plants, measures saving a total of $$147 million per year have been implemented, measures that will save $169 million per year are in the process of being implemented, and plants are planning implementation of measures that will save another $239 million per year. The implemented recommendations are already achieving total CO{sub 2} reductions of about 1.8 million metric tons per year. This report provides a summary of the key results for the Save Energy Now assessments completed in 2008; details of the 6-month, 12-month, and 24-month implementation results obtained to date; and an evaluation of these implementation results. This report also summarizes key accomplishments, findings, and lessons learned from all the Save Energy Now assessments completed to date. A separate report (Wright et al. 2010) provides more detailed information on key results for all of the 2008 assessments of steam, process heating, pumping, compressed air, and fan systems. Two prior reports (Wright et al. 2007 and Wright et al. 2009) detail the results from the 2006 and 2007 assessments and discuss the major components of the assessment process and improvements in the process made in 2007.« less

Effects of Microwave Radiation on Oil Recovery

NASA Astrophysics Data System (ADS)

Esmaeili, Abdollah

2011-12-01

A variety of oil recovery methods have been developed and applied to mature and depleted reservoirs in order to improve the efficiency. Microwave radiation oil recovery method is a relatively new method and has been of great interest in the recent years. Crude oil is typically co-mingled with suspended solids and water. To increase oil recovery, it is necessary to remove these components. The separation of oil from water and solids using gravitational settling methods is typically incomplete. Oil-in-water and oil-water-solid emulsions can be demulsified and separated into their individual layers by microwave radiation. The data also show that microwave separation is faster than gravity separation and can be faster than conventional heating at many conditions. After separation of emulsion into water and oil layers, water can be discharged and oil is collected. High-frequency microwave recycling process can recover oil and gases from oil shale, residual oil, drill cuttings, tar sands oil, contaminated dredge/sediments, tires and plastics with significantly greater yields and lower costs than are available utilizing existing known technologies. This process is environmentally friendly, fuel-generating recycler to reduce waste, cut emissions, and save energy. This paper presents a critical review of Microwave radiation method for oil recovery.

Technical Support Document: 50% Energy Savings Design Technology Packages for Highway Lodging Buildings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jiang, Wei; Gowri, Krishnan; Lane, Michael D.

2009-09-28

This Technical Support Document (TSD) describes the process, methodology and assumptions for development of the 50% Energy Savings Design Technology Packages for Highway Lodging Buildings, a design guidance document intended to provide recommendations for achieving 50% energy savings in highway lodging properties over the energy-efficiency levels contained in ANSI/ASHRAE/IESNA Standard 90.1-2004, Energy Standard for Buildings Except Low-Rise Residential Buildings.

The Myth About Saving Money: "IT Investments Will Save The Institution Money"

ERIC Educational Resources Information Center

Hawkins, Brian L.; Oblinger, Diana G.

2005-01-01

Claims that investing in information technology will save money for a college or university have rarely proven true. In fact, realizing the promised dollar savings is so rare in higher education that the credibility of many IT professionals has been jeopardized by making the claim. Not producing promised savings only exacerbates the sense, among…

26 CFR 1.149(d)-1A - Limitations on advance refundings.

Code of Federal Regulations, 2010 CFR

2010-04-01

... savings test. If any separate issue in a multipurpose issue increases the aggregate present value debt service savings on the entire multipurpose issue or reduces the present value debt service losses on that...

31 CFR 359.30 - Are definitive Series I savings bonds purchased in the name of an individual computed separately...

Code of Federal Regulations, 2010 CFR

2010-07-01

... 31 Money and Finance: Treasury 2 2010-07-01 2010-07-01 false Are definitive Series I savings bonds....30 Section 359.30 Money and Finance: Treasury Regulations Relating to Money and Finance (Continued) FISCAL SERVICE, DEPARTMENT OF THE TREASURY BUREAU OF THE PUBLIC DEBT OFFERING OF UNITED STATES SAVINGS...

Using Technology to Control Costs

ERIC Educational Resources Information Center

Ho, Simon; Schoenberg, Doug; Richards, Dan; Morath, Michael

2009-01-01

In this article, the authors examines the use of technology to control costs in the child care industry. One of these technology solutions is Software-as-a-Service (SaaS). SaaS solutions can help child care providers save money in many aspects of center management. In addition to cost savings, SaaS solutions are also particularly appealing to…

Maximizing Residential Energy Savings: Net Zero Energy House (ZEH) Technology Pathways

DOE Office of Scientific and Technical Information (OSTI.GOV)

Anderson, R.; Roberts, D.

To meet current U.S. Department of Energy zero-energy home performance goals, new technologies and solutions must increase whole-house efficiency savings by an additional 40% relative to those provided by best available components and systems.

A Summary of Research on Energy Saving and Emission Reduction of Transportation

NASA Astrophysics Data System (ADS)

Cheng, Dongxiang; Wu, Lufen

2017-12-01

Road transport is an important part of transportation, and road in the field of energy-saving emission reduction is a very important industry. According to the existing problems of road energy saving and emission reduction, this paper elaborates the domestic and international research on energy saving and emission reduction from three aspects: road network optimization, pavement material and pavement maintenance. Road network optimization may be overlooked, and the research content is still relatively preliminary; pavement materials mainly from the asphalt pavement temperature mixed asphalt technology research; pavement maintenance technology development is relatively comprehensive.

Competence formation of engineering directions students in the field of energy saving as a way to create new generation technologies

NASA Astrophysics Data System (ADS)

Gilmanshin, I. R.; Gilmanshina, S. I.

2017-09-01

The urgency of the formation of competence in the field of energy saving in the process of studying engineering and technical disciplines at the university is substantiated. The author’s definition of the competence in the field of energy saving is given, allowing to consider the necessity of its formation among students - future engineers as a way to create technologies of a new generation. The essence of this competence is revealed. The system of work, pedagogical conditions and technologies of its formation in the conditions of the federal university is substantiated.

Removal of micropollutants with coarse-ground activated carbon for enhanced separation with hydrocyclone classifiers.

PubMed

Otto, N; Platz, S; Fink, T; Wutscherk, M; Menzel, U

2016-01-01

One key technology to eliminate organic micropollutants (OMP) from wastewater effluent is adsorption using powdered activated carbon (PAC). To avoid a discharge of highly loaded PAC particles into natural water bodies a separation stage has to be implemented. Commonly large settling tanks and flocculation filters with the application of coagulants and flocculation aids are used. In this study, a multi-hydrocyclone classifier with a downstream cloth filter has been investigated on a pilot plant as a space-saving alternative with no need for a dosing of chemical additives. To improve the separation, a coarser ground PAC type was compared to a standard PAC type with regard to elimination results of OMP as well as separation performance. With a PAC dosing rate of 20 mg/l an average of 64.7 wt% of the standard PAC and 79.5 wt% of the coarse-ground PAC could be separated in the hydrocyclone classifier. A total average separation efficiency of 93-97 wt% could be reached with a combination of both hydrocyclone classifier and cloth filter. Nonetheless, the OMP elimination of the coarse-ground PAC was not sufficient enough to compete with the standard PAC. Further research and development is necessary to find applicable coarse-grained PAC types with adequate OMP elimination capabilities.

Real-time monitoring system for improving corona electrostatic separation in the process of recovering waste printed circuit boards.

PubMed

Li, Jia; Zhou, Quan; Xu, Zhenming

2014-12-01

Although corona electrostatic separation is successfully used in recycling waste printed circuit boards in industrial applications, there are problems that cannot be resolved completely, such as nonmetal particle aggregation and spark discharge. Both of these problems damage the process of separation and are not easy to identify during the process of separation in industrial applications. This paper provides a systematic study on a real-time monitoring system. Weight monitoring systems were established to continuously monitor the separation process. A Virtual Instrumentation program written by LabVIEW was utilized to sample and analyse the mass increment of the middling product. It includes four modules: historical data storage, steady-state analysis, data computing and alarm. Three kinds of operating conditions were used to verify the applicability of the monitoring system. It was found that the system achieved the goal of monitoring during the separation process and realized the function of real-time analysis of the received data. The system also gave comprehensible feedback on the accidents of material blockages in the feed inlet and high-voltage spark discharge. With the warning function of the alarm system, the whole monitoring system could save the human cost and help the new technology to be more easily applied in industry. © The Author(s) 2014.

2007 National Small Business Conference: Critical Infrastructure Opportunities

DTIC Science & Technology

2007-05-18

Flooding of Subway Tunnels From IED Bomber Maximize lives saved – provide time to evacuate Recent advances in inflatable structure technology: • Stronger...Polimetry/ Signal Processing technologies (Radar & Sonar) Low Cost Advanced Composite Structures Low Cost Composite Sandwich Structures and...Ubiquitous Chem/Bio Detect 34 High Impact Technology Solutions Resilient Tunnel Prevent Flooding of Subway Tunnels From IED Bomber Maximize lives saved

Smart material screening machines using smart materials and controls

NASA Astrophysics Data System (ADS)

Allaei, Daryoush; Corradi, Gary; Waigand, Al

2002-07-01

The objective of this product is to address the specific need for improvements in the efficiency and effectiveness in physical separation technologies in the screening areas. Currently, the mining industry uses approximately 33 billion kW-hr per year, costing 1.65 billion dollars at 0.05 cents per kW-hr, of electrical energy for physical separations. Even though screening and size separations are not the single most energy intensive process in the mining industry, they are often the major bottleneck in the whole process. Improvements to this area offer tremendous potential in both energy savings and production improvements. Additionally, the vibrating screens used in the mining processing plants are the most costly areas from maintenance and worker health and safety point of views. The goal of this product is to reduce energy use in the screening and total processing areas. This goal is accomplished by developing an innovative screening machine based on smart materials and smart actuators, namely smart screen that uses advanced sensory system to continuously monitor the screening process and make appropriate adjustments to improve production. The theory behind the development of Smart Screen technology is based on two key technologies, namely smart actuators and smart Energy Flow ControlT (EFCT) strategies, developed initially for military applications. Smart Screen technology controls the flow of vibration energy and confines it to the screen rather than shaking much of the mass that makes up the conventional vibratory screening machine. Consequently, Smart Screens eliminates and downsizes many of the structural components associated with conventional vibratory screening machines. As a result, the surface area of the screen increases for a given envelope. This increase in usable screening surface area extends the life of the screens, reduces required maintenance by reducing the frequency of screen change-outs and improves throughput or productivity.

Parafricta Bootees and Undergarments to Reduce Skin Breakdown in People with or at Risk of Pressure Ulcers: A NICE Medical Technologies Guidance.

PubMed

Meads, Catherine; Glover, Matthew; Dimmock, Paul; Pokhrel, Subhash

2016-12-01

As part of the development of the National Institute for Health and Care Excellence (NICE) Medical Technologies Guidance on Parafricta Bootees and Undergarments to reduce skin breakdown in people with, or at risk of, pressure ulcers, the manufacturer (APA Parafricta Ltd) submitted clinical and economic evidence, which was critically appraised by an External Assessment Centre (EAC) and subsequently used by the Medical Technologies Advisory Committee (MTAC) to develop recommendations for further research. The University of Birmingham and Brunel University, acting as a consortium, were commissioned to act as the EAC, independently appraising the submission. This article is an overview of the original evidence submitted, the EAC's findings and the final NICE guidance. Very little comparative evidence was submitted to demonstrate the effectiveness of Parafricta Bootees or Undergarments. The sponsor submitted a simple cost analysis to estimate the costs of using Parafricta in addition to current practice-in comparison with current practice alone-in hospital and community settings separately. The analysis took a National Health Service (NHS) perspective. The basis of the analysis was a previously published comparative study, which showed no statistical difference in average lengths of stay between patients who wore Parafricta Undergarments and Bootees, and those who did not. The economic model incorporated the costs of Parafricta but assumed shorter lengths of stay with Parafricta. The sponsor concluded that Parafricta was cost saving relative to the comparators. The EAC made amendments to the sponsor's analysis to correct for errors and to reflect alternative assumptions. Parafricta remained cost saving in most analyses, and the savings per prevalent case ranged from £757 in the hospital model to £3455 in the community model. All analyses were severely limited by the available data on effectiveness-in particular, a lack of good-quality comparative studies.

Technology for Water Treatment

NASA Technical Reports Server (NTRS)

1992-01-01

There are approximately 500,000 water cooling towers in the United States, all of which must be kept clear of "scale" and corrosion and free of pollutants and bacteria. Electron Pure, Ltd. manufactures a hydro cooling tower conditioner as well as an automatic pool sanitizer. The pool sanitizer consists of two copper/silver electrodes placed in a chamber mounted in the pool's recirculation system. The tower conditioner combines the ionization system with a water conditioner, pump, centrifugal solids separator and timer. The system saves water, eliminates algae and operates maintenance and chemical free. The company has over 100 distributors in the U.S. as well as others in 20 foreign countries. The buildup of scale and corrosion is the most costly maintenance problem in cooling tower operation. Jet Propulsion Laboratory successfully developed a non-chemical system that not only curbed scale and corrosion, but also offered advantages in water conservation, cost savings and the elimination of toxic chemical discharge. In the system, ozone is produced by an on-site generator and introduced to the cooling tower water. Organic impurities are oxidized, and the dissolved ozone removes bacteria and scale. National Water Management, a NASA licensee, has installed its ozone advantage systems at some 200 cooling towers. Customers have saved money and eliminated chemical storage and discharge.

ResStock - Targeting Energy and Cost Savings for U.S. Homes | NREL

Science.gov Websites

ResStock - Targeting Energy and Cost Savings for U.S. Homes Science and Technology Highlights Highlights in Research & Development ResStock - Targeting Energy and Cost Savings for U.S. Homes Key discovered $49 billion in potential annual utility bill savings through cost-effective energy efficiency

Low-Emissivity, Energy-Control, Retrofit Window Film: Final Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Winckler, Lisa

Solutia Performance Films, utilizing funding from the U.S. Department of Energy's Buildings Technologies Program, completed research to develop, validate, and commercialize a range of cost-effective, low-emissivity energy-control retrofit window films with significantly improved emissivity over current technology. These films, sold under the EnerLogic® trade name, offer the energy-saving properties of modern low-e windows, with several advantages over replacement windows, such as: lower initial installation cost, a significantly lower product carbon footprint, and an ability to provide a much faster return on investment. EnerLogic® window films also offer significantly greater energy savings than previously available with window films with similar visiblemore » light transmissions. EnerLogic® window films offer these energy-saving advantages over other window films due to its ability to offer both summer cooling and winter heating savings. Unlike most window films, that produce savings only during the cooling season, EnerLogic® window film is an all-season, low-emissivity (low-e) film that produces both cooling and heating season savings. This paper will present technical information on the development hurdles as well as details regarding the following claims being made about EnerLogic® window film, which can be found at www.EnerLogicfilm.com: 1. Other window film technologies save energy. EnerLogic® window film's patent-pending coating delivers excellent energy efficiency in every season, so no other film can match its annual dollar or energy consumption savings. 2. EnerLogic® window film is a low-cost, high-return technology that compares favorably to other popular energy-saving measures both in terms of energy efficiency and cost savings. In fact, EnerLogic® window film typically outperforms most of the alternatives in terms of simple payback. 3. EnerLogic® window film provides unparalleled glass insulating capabilities for window film products. With its patent-pending low-e technology, EnerLogic® window film has the best insulating performance of any film product available. The insulating power of EnerLogic® window film gives single-pane windows the annual insulating performance of double-pane windows - and gives double-pane windows the annual insulating performance of triple-pane windows.« less

Energy Efficiency Opportunities in Highway Lodging Buildings: Development of 50% Energy Savings Design Technology Packages

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jiang, Wei; Gowri, Krishnan; Thornton, Brian A.

2010-06-30

This paper presents the process, methodology, and assumptions for development of the 50% Energy Savings Design Technology Packages for Highway Lodging Buildings, a design guidance document that provides specific recommendations for achieving 50% energy savings in roadside motels (highway lodging) above the requirements of ANSI/ASHRAE/IESNA Standard 90.1-2004. This 50% solution represents a further step toward realization of the U.S. Department of Energy’s net-zero energy building goal, and go beyond the 30% savings in the Advanced Energy Design Guide series (upon which this work was built). This work can serve as the technical feasibility study for the development of a 50%more » saving Advanced Energy Design Guide for highway lodging, and thus should greatly expedite the development process. The purpose of this design package is to provide user-friendly design assistance to designers, developers, and owners of highway lodging properties. It is intended to encourage energy-efficient design by providing prescriptive energy-efficiency recommendations for each climate zone that attains the 50% the energy savings target. This paper describes the steps that were taken to demonstrate the technical feasibility of achieving a 50% reduction in whole-building energy use with practical and commercially available technologies. The energy analysis results are presented, indicating the recommended energy-efficient measures achieved a national-weighted average energy savings of 55%, relative to Standard 90.1-2004. The cost-effectiveness of the recommended technology package is evaluated and the result shows an average simple payback of 11.3 years.« less

Performance Contracting: Taking School Technology Green

ERIC Educational Resources Information Center

Taival, Dane

2009-01-01

Energy efficiency makes fiscal and environmental sense, and so does energy savings performance contracting. Because an energy savings performance contract can create a self-funding package of products and services that reduce energy and operating costs, over time, school districts' sometimes-large initial investment in emerging technologies saves…

Scaleable production and separation of fermentation-derived acetic acid. Final CRADA report.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Snyder, S. W.; Energy Systems

2010-02-08

Half of U.S. acetic acid production is used in manufacturing vinyl acetate monomer (VAM) and is economical only in very large production plants. Nearly 80% of the VAM is produced by methanol carbonylation, which requires high temperatures and exotic construction materials and is energy intensive. Fermentation-derived acetic acid production allows for small-scale production at low temperatures, significantly reducing the energy requirement of the process. The goal of the project is to develop a scaleable production and separation process for fermentation-derived acetic acid. Synthesis gas (syngas) will be fermented to acetic acid, and the fermentation broth will be continuously neutralized withmore » ammonia. The acetic acid product will be recovered from the ammonium acid broth using vapor-based membrane separation technology. The process is summarized in Figure 1. The two technical challenges to success are selecting and developing (1) microbial strains that efficiently ferment syngas to acetic acid in high salt environments and (2) membranes that efficiently separate ammonia from the acetic acid/water mixture and are stable at high enough temperature to facilitate high thermal cracking of the ammonium acetate salt. Fermentation - Microbial strains were procured from a variety of public culture collections (Table 1). Strains were incubated and grown in the presence of the ammonium acetate product and the fastest growing cultures were selected and incubated at higher product concentrations. An example of the performance of a selected culture is shown in Figure 2. Separations - Several membranes were considered. Testing was performed on a new product line produced by Sulzer Chemtech (Germany). These are tubular ceramic membranes with weak acid functionality (see Figure 3). The following results were observed: (1) The membranes were relatively fragile in a laboratory setting; (2) Thermally stable {at} 130 C in hot organic acids; (3) Acetic acid rejection > 99%; and (4) Moderate ammonia flux. The advantages of producing acetic acid by fermentation include its appropriateness for small-scale production, lower cost feedstocks, low energy membrane-based purification, and lower temperature and pressure requirements. Potential energy savings of using fermentation are estimated to be approximately 14 trillion Btu by 2020 from a reduction in natural gas use. Decreased transportation needs with regional plants will eliminate approximately 200 million gallons of diesel consumption, for combined savings of 45 trillion Btu. If the fermentation process captures new acetic acid production, savings could include an additional 5 trillion Btu from production and 7 trillion Btu from transportation energy.« less

Clean Cities 2016 Vehicle Buyer's Guide

DOE Office of Scientific and Technical Information (OSTI.GOV)

2016-02-01

Drivers and fleets are increasingly turning to the hundreds of light-duty, alternative fuel, and advanced technology vehicle models that reduce petroleum use, save on fuel costs, and cut emissions. This guide provides a comprehensive list of the 2016 light-duty models that use alternative fuels or advanced fuel-saving technologies.

Alternative Fuels Data Center: Idle Reduction

Science.gov Websites

Cities Annual Petroleum Savings Clean Cities Annual Petroleum Savings Incentive and Law Additions by Fuel /Technology Type Incentive and Law Additions by Fuel/Technology Type Incentive Additions by Policy Type Incentive Additions by Policy Type More Idle Reduction Data | All Maps & Data Case Studies Massachusetts

Design, Specification and Construction of Specialized Measurement System in the Experimental Building

NASA Astrophysics Data System (ADS)

Fedorczak-Cisak, Malgorzata; Kwasnowski, Pawel; Furtak, Marcin; Hayduk, Grzegorz

2017-10-01

Experimental buildings for “in situ” research are a very important tool for collecting data on energy efficiency of the energy-saving technologies. One of the most advanced building of this type in Poland is the Maloposkie Laboratory of Energy-saving Buildings at Cracow University of Technology. The building itself is used by scientists as a research object and research tool to test energy-saving technologies. It is equipped with a specialized measuring system consisting of approx. 3 000 different sensors distributed in technical installations and structural elements of the building (walls, ceilings, cornices) and the ground. The authors of the paper will present the innovative design and technology of this specialized instrumentation. They will discuss issues arising during the implementation and use of the building.

Energy and cost saving results for advanced technology systems from the Cogeneration Technology Alternatives Study (CTAS)

NASA Technical Reports Server (NTRS)

Sagerman, G. D.; Barna, G. J.; Burns, R. K.

1979-01-01

An overview of the organization and methodology of the Cogeneration Technology Alternatives Study is presented. The objectives of the study were to identify the most attractive advanced energy conversion systems for industrial cogeneration applications in the future and to assess the advantages of advanced technology systems compared to those systems commercially available today. Advanced systems studied include steam turbines, open and closed cycle gas turbines, combined cycles, diesel engines, Stirling engines, phosphoric acid and molten carbonate fuel cells and thermionics. Steam turbines, open cycle gas turbines, combined cycles, and diesel engines were also analyzed in versions typical of today's commercially available technology to provide a base against which to measure the advanced systems. Cogeneration applications in the major energy consuming manufacturing industries were considered. Results of the study in terms of plant level energy savings, annual energy cost savings and economic attractiveness are presented for the various energy conversion systems considered.

Application of advanced technologies to derivatives of current small transport aircraft

NASA Technical Reports Server (NTRS)

Renze, P. P.; Terry, J. E.

1981-01-01

Mission requirements of the derivative design were the same as the baseline to readily identify the advanced technology benefits achieved. Advanced technologies investigated were in the areas of propulsion, structures and aerodynamics and a direct operating cost benefit analysis conducted to identify the most promising. Engine improvements appear most promising and combined with propeller, airfoil, surface coating and composite advanced technologies give a 21-25 percent DOC savings. A 17 percent higher acquisition cost is offset by a 34 percent savings in fuel used.

Energy conservation through sealing technology

NASA Technical Reports Server (NTRS)

Stair, W. K.; Ludwig, L. P.

1978-01-01

Improvements in fluid film sealing resulting from a proposed research program could lead to an annual energy saving, on a national basis, equivalent to about 37 million bbl of oil or 0.3% of the total U.S. energy consumption. Further, the application of known sealing technology can result in an annual saving of an additional 10 million bbl of oil. The energy saving would be accomplished by reduction in process heat energy loss, reduction of frictional energy generated, and minimization of energy required to operate ancillary equipment associated with the seal system. In addition to energy saving, cost effectiveness is further enhanced by reduction in maintenance and in minimization of equipment for collecting leakage and for meeting environmental pollution standards.

48 CFR 23.205 - Energy-savings performance contracts.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 48 Federal Acquisition Regulations System 1 2012-10-01 2012-10-01 false Energy-savings performance... SOCIOECONOMIC PROGRAMS ENVIRONMENT, ENERGY AND WATER EFFICIENCY, RENEWABLE ENERGY TECHNOLOGIES, OCCUPATIONAL SAFETY, AND DRUG-FREE WORKPLACE Energy and Water Efficiency and Renewable Energy 23.205 Energy-savings...

48 CFR 23.205 - Energy-savings performance contracts.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 48 Federal Acquisition Regulations System 1 2010-10-01 2010-10-01 false Energy-savings performance... SOCIOECONOMIC PROGRAMS ENVIRONMENT, ENERGY AND WATER EFFICIENCY, RENEWABLE ENERGY TECHNOLOGIES, OCCUPATIONAL SAFETY, AND DRUG-FREE WORKPLACE Energy and Water Efficiency and Renewable Energy 23.205 Energy-savings...

48 CFR 23.205 - Energy-savings performance contracts.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 48 Federal Acquisition Regulations System 1 2013-10-01 2013-10-01 false Energy-savings performance... SOCIOECONOMIC PROGRAMS ENVIRONMENT, ENERGY AND WATER EFFICIENCY, RENEWABLE ENERGY TECHNOLOGIES, OCCUPATIONAL SAFETY, AND DRUG-FREE WORKPLACE Energy and Water Efficiency and Renewable Energy 23.205 Energy-savings...

48 CFR 23.205 - Energy-savings performance contracts.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 48 Federal Acquisition Regulations System 1 2014-10-01 2014-10-01 false Energy-savings performance... SOCIOECONOMIC PROGRAMS ENVIRONMENT, ENERGY AND WATER EFFICIENCY, RENEWABLE ENERGY TECHNOLOGIES, OCCUPATIONAL SAFETY, AND DRUG-FREE WORKPLACE Energy and Water Efficiency and Renewable Energy 23.205 Energy-savings...

48 CFR 23.205 - Energy-savings performance contracts.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 48 Federal Acquisition Regulations System 1 2011-10-01 2011-10-01 false Energy-savings performance... SOCIOECONOMIC PROGRAMS ENVIRONMENT, ENERGY AND WATER EFFICIENCY, RENEWABLE ENERGY TECHNOLOGIES, OCCUPATIONAL SAFETY, AND DRUG-FREE WORKPLACE Energy and Water Efficiency and Renewable Energy 23.205 Energy-savings...

U.S. Department of Energy’s Industrial Technologies Program and Its Impacts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Weakley, Steven A.; Brown, Scott A.

The U.S. Department of Energy’s Industrial Technologies Program (ITP) has been working with industry since 1976 to encourage the development and adoption of new, energy-efficient technologies. ITP has helped industry not only use energy and materials more efficiently but also improve environ-mental performance, product quality, and productivity. To help ITP determine the impacts of its pro-grams, Pacific Northwest National Laboratory (PNNL) periodically reviews and analyzes ITP pro-gram benefits. PNNL contacts vendors and users of ITP-sponsored technologies that have been commer-cialized, estimates the number of units that have penetrated the market, conducts engineering analyses to estimate energy savings from the newmore » technolo-gies, and estimates air pollution and carbon emission reductions. This paper discusses the results of PNNL’s most recent review (conducted in 2010). From 1976-2009, the commercialized technologies from ITP’s research and development programs and other activities have cumulatively saved 10.0 quadrillion Btu, with a net cost savings of $61.82 billion.« less

Energy Efficient Engine Flight Propulsion System Preliminary Analysis and Design Report

NASA Technical Reports Server (NTRS)

Bisset, J. W.; Howe, D. C.

1983-01-01

The final design and analysis of the flight propulsion system is presented. This system is the conceptual study engine defined to meet the performance, economic and environmental goals established for the Energy Efficient Engine Program. The design effort included a final definition of the engine, major components, internal subsystems, and nacelle. Various analytical representations and results from component technology programs are used to verify aerodynamic and structural design concepts and to predict performance. Specific design goals and specifications, reflecting future commercial aircraft propulsion system requirements for the mid-1980's, are detailed by NASA and used as guidelines during engine definition. Information is also included which details salient results from a separate study to define a turbofan propulsion system, known as the maximum efficiency engine, which reoptimized the advanced fuel saving technologies for improved fuel economy and direct operating costs relative to the flight propulsion system.

Aerodynamic Drag Reduction Technologies Testing of Heavy-Duty Vocational Vehicles and a Dry Van Trailer

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ragatz, Adam; Thornton, Matthew

This study focused on two accepted methods for quantifying the benefit of aerodynamic improvement technologies on vocational vehicles: the coastdown technique, and on-road constant speed fuel economy measurements. Both techniques have their advantages. Coastdown tests are conducted over a wide range in speed and allow the rolling resistance and aerodynamic components of road load force to be separated. This in turn allows for the change in road load and fuel economy to be estimated at any speed, as well as over transient cycles. The on-road fuel economy measurements only supply one lumped result, applicable at the specific test speed, butmore » are a direct measurement of fuel usage and are therefore used in this study as a check on the observed coastdown results. Resulting coefficients were then used to populate a vehicle model and simulate expected annual fuel savings over real-world vocational drive cycles.« less

Sino-US cooperation in water saving technologies: essential international problems

USDA-ARS?s Scientific Manuscript database

The United States and China share many agricultural problems, but one of great importance is the need to produce more crop yield in the face of water scarcity. Common recognition of this problem led to the development of a joint Sino-US Water Saving Technologies Flagship project within the larger US...

Cabin Pressure Monitors Notify Pilots to Save Lives

NASA Technical Reports Server (NTRS)

2015-01-01

In 2013, San Diego-based Aviation Technology Inc. obtained an exclusive license for the technology behind the cabin pressure monitor invented at Kennedy Space Center and built its own version of the product. The Alt Alert is designed to save lives by alerting aircraft pilots and crews when cabin pressure becomes dangerously low.

Reactors Save Energy, Costs for Hydrogen Production

NASA Technical Reports Server (NTRS)

2014-01-01

While examining fuel-reforming technology for fuel cells onboard aircraft, Glenn Research Center partnered with Garrettsville, Ohio-based Catacel Corporation through the Glenn Alliance Technology Exchange program and a Space Act Agreement. Catacel developed a stackable structural reactor that is now employed for commercial hydrogen production and results in energy savings of about 20 percent.

Building energy information systems: Synthesis of costs, savings, and best-practice uses

DOE PAGES

Granderson, Jessica; Lin, Guanjing

2016-02-19

Building energy information systems (EIS) are a powerful customer-facing monitoring and analytical technology that can enable up to 20% site energy savings for buildings. Few technologies are as heavily marketed, but in spite of their potential, EIS remain an under-adopted emerging technology. One reason is the lack of information on purchase costs and associated energy savings. While insightful, the growing body of individual case studies has not provided industry the information needed to establish the business case for investment. Vastly different energy and economic metrics prevent generalizable conclusions. This paper addresses three common questions concerning EIS use: what are themore » costs, what have users saved, and which best practices drive deeper savings? We present a large-scale assessment of the value proposition for EIS use based on data from over two-dozen organizations. Participants achieved year-over-year median site and portfolio savings of 17% and 8%, respectively; they reported that this performance would not have been possible without the EIS. The median five-year cost of EIS software ownership (up-front and ongoing costs) was calculated to be $1,800 per monitoring point (kilowatt meter points were most common), with a median portfolio-wide implementation size of approximately 200 points. In this paper, we present an analysis of the relationship between key implementation factors and achieved energy reductions. Extent of efficiency projects, building energy performance prior to EIS installation, depth of metering, and duration of EIS were strongly correlated with greater savings. As a result, we also identify the best practices use of EIS associated with greater energy savings.« less

Building energy information systems: Synthesis of costs, savings, and best-practice uses

DOE Office of Scientific and Technical Information (OSTI.GOV)

Granderson, Jessica; Lin, Guanjing

Building energy information systems (EIS) are a powerful customer-facing monitoring and analytical technology that can enable up to 20% site energy savings for buildings. Few technologies are as heavily marketed, but in spite of their potential, EIS remain an under-adopted emerging technology. One reason is the lack of information on purchase costs and associated energy savings. While insightful, the growing body of individual case studies has not provided industry the information needed to establish the business case for investment. Vastly different energy and economic metrics prevent generalizable conclusions. This paper addresses three common questions concerning EIS use: what are themore » costs, what have users saved, and which best practices drive deeper savings? We present a large-scale assessment of the value proposition for EIS use based on data from over two-dozen organizations. Participants achieved year-over-year median site and portfolio savings of 17% and 8%, respectively; they reported that this performance would not have been possible without the EIS. The median five-year cost of EIS software ownership (up-front and ongoing costs) was calculated to be $1,800 per monitoring point (kilowatt meter points were most common), with a median portfolio-wide implementation size of approximately 200 points. In this paper, we present an analysis of the relationship between key implementation factors and achieved energy reductions. Extent of efficiency projects, building energy performance prior to EIS installation, depth of metering, and duration of EIS were strongly correlated with greater savings. As a result, we also identify the best practices use of EIS associated with greater energy savings.« less

Lighting retrofits at the Pittsburgh Zoo and Aviary

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sadowski, E.C.

Energy bills for the Pittsburgh Zoo typically total $280,000 a year, of which about $220,000 are spent on electricity. Until recently, lighting accounted for 20 percent of this electricity use. This translated into an annual cost of $44,000. Recent advances in lighting technology have made it possible to perform lighting retrofits in Zoo facilities that reduce energy costs while also providing improved light quality and better lit and more natural looking exhibits and animal holding areas. Through an investment of $127,690 in these projects from mid-1992 through mid-1994, the Zoo expects to realize an annual savings in electricity costs ofmore » $24,500 and further savings from a reduction in maintenance and plant replacement costs. Retrofits to the lighting systems in the Tropical Forest Building, the Aquarium, and the Niches of the World Building were the most interesting and are described in detail. Providing a sufficient amount of ultraviolet light to maintain the health of reptiles was a particular challenge in the Niches of the World Building. Lack of separate meters and additions to the Zoo have made the determination of the actual performance of these retrofit projects impossible. A similar retrofit project at the Pittsburgh Aviary (now the National Aviary) in 1989 through 1990 provides savings figures that should be comparable to those expected at the Zoo, however. This project cost $100,000 and saved $21,008 in electricity costs during the first year of operation. Maintenance costs were reduced by approximately $5000 a year.« less

Recent Advances and Research Status in Energy Conservation of Iron Ore Sintering in China

NASA Astrophysics Data System (ADS)

Wang, Yao-Zu; Zhang, Jian-Liang; Liu, Zheng-Jian; Du, Cheng-Bo

2017-11-01

For the ferrous burden of blast furnaces in China, sinter generally accounts for more than 70% and the sintering process accounts for approximately 6-10% of the total energy consumption of the iron and steel enterprise. Therefore, saving energy during the sintering process is important to reduce the energy consumption in the iron and steel industry. This paper aims to illustrate recent advances and the research status of energy conservation of iron ore sintering in China. It focuses on the development and application of energy-saving technologies such as the composite agglomeration process, sintering with high-proportion flue gas recirculation sintering, recovery of sensible heat from the sinter cooling process, homogeneous deep-bed sintering technology, and comprehensive treatment technology of leakage of sintering. Moreover, some suggestions for the future development of energy-saving technologies are put forward.

Improvement in gold grade from iron-oxide mineral using reduction roasting and magnetic separation

NASA Astrophysics Data System (ADS)

Kim, Hyun-soo; On, Hyun-sung; Lim, Dae-hack; Myung, Eun-ji; Park, Cheon-young

2017-04-01

Microwave has a wide range of applications in mineral technology, metallurgy, etc. It is an established fact that microwave energy has potential for the speedy and efficient heating of minerals and in a commercial context may provide savings in both time and energy. Microwave heating is being developed as a potential thermal pre-treatment process, because of its unique advantages over the differences of ore minerals in absorbing microwaves. The aim of this study was to investigate the improvement in Au grade from iron-oxide mineral using reduction roasting and magnetic separation. The characteristics of iron-oxide mineral were analyzed using chemical, XRD and reflected light microscopy. The reduction roasting using microwave and magnetic separation experiments were examined under various conditions (reducing agent and chemical additive). The results of XRD and reflected light microscopy showed that the iron-oxide mineral mainly composed of illite, quartz and hematite. The iron-oxide mineral had an Au, Ag, Fe contents of 6.4, 35.1 and 155,441.1 mg/kg, respectively. The results demonstrated that the improvement in Au by reduction roasting using microwave (frequency of 2.45GHz, intensity of 5kW) and magnetic separation (magnetic field intensity of 9,000 Gauss) were effective processes. The Au content in iron-oxide mineral from 6.4 mg/kg to 14.2 mg/kg was achieved within microwave exposure time of 10min (reducing agent(PAC) ratio = 50 : 50, 5% of chemical additive(Soda ash)). Acknowledgment : This subject is supported by Korea Ministry of Environment as "Advanced Technology Program for Environmental Industry"

Understanding and modeling the economics of ECM

NASA Astrophysics Data System (ADS)

Wells, Wayne E.; Edinbarough, Immanuel A.

2004-12-01

Traditional economic analysis methods for manufacturing decisions include only the clearly identified immediate cost and revenue streams. Environmental issues have generally been seen as costs, in the form of waste material losses, conformance tests and pre-discharge treatments. The components of the waste stream often purchased as raw materials, become liabilities at the "end of the pipe" and their intrinsic material value is seldom recognized. A new mathematical treatment of manufacturing economics is proposed in which the costs of separation are compared with the intrinsic value of the waste materials to show how their recovery can provide an economic advantage to the manufacturer. The model is based on a unique combination of thermodynamic analysis, economic modeling and linear optimization. This paper describes the proposed model, and examines case studies in which the changed decision rules have yielded significant savings while protecting the environment. The premise proposed is that by including the value of the waste materials in the profit objective of the firm and applying the appropriate technological solution, manufacturing processes can become closed systems in which losses approach zero and environmental problems are converted into economic savings.

Textile composite fuselage structures development

NASA Technical Reports Server (NTRS)

Jackson, Anthony C.; Barrie, Ronald E.; Chu, Robert L.

1993-01-01

Phase 2 of the NASA ACT Contract (NAS1-18888), Advanced Composite Structural Concepts and Materials Technology for Transport Aircraft Structures, focuses on textile technology, with resin transfer molding or powder coated tows. The use of textiles has the potential for improving damage tolerance, reducing cost and saving weight. This program investigates resin transfer molding (RTM), as a maturing technology for high fiber volume primary structures and powder coated tows as an emerging technology with a high potential for significant cost savings and superior structural properties. Powder coated tow technology has promise for significantly improving the processibility of high temperature resins such as polyimides.

Outplacement Services in Support of BRAC and Competitive Sourcing Task Group

DTIC Science & Technology

2003-07-30

Management(SM) is an automated Web-based solution that streamlines workforce adjustment initiatives and exit processing, saving time and money by getting...effected during FY02 – almost 7,000. o Over 160,000 employees have been saved from involuntary separation since program inception in 1993. Buyouts...monetary incentive, up to $25,000, for employee to retire, either optional or early, or resign. Payment of the incentive must save another DoD employee

Assessment Study on Sensors and Automation in the Industries of the Future. Reports on Industrial Controls, Information Processing, Automation, and Robotics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bennett, Bonnie; Boddy, Mark; Doyle, Frank

This report presents the results of an expert study to identify research opportunities for Sensors & Automation, a sub-program of the U.S. Department of Energy (DOE) Industrial Technologies Program (ITP). The research opportunities are prioritized by realizable energy savings. The study encompasses the technology areas of industrial controls, information processing, automation, and robotics. These areas have been central areas of focus of many Industries of the Future (IOF) technology roadmaps. This report identifies opportunities for energy savings as a direct result of advances in these areas and also recognizes indirect means of achieving energy savings, such as product quality improvement,more » productivity improvement, and reduction of recycle.« less

Aggressive Strategies for Residential Energy and Carbon Savings by 2025

NASA Astrophysics Data System (ADS)

Ling, F. H.; Kammen, D. M.

2004-12-01

Energy efficiency technologies and practices have long been recognized as a low-cost, often least cost, option that can be deployed widely throughout the economy (Steve Nadel, 2002; Donald A. Hanson and John A. Laitner, 2003). We are engaged in a review of technology-based energy savings options throughout the U. S. economy with a joint focus on both immediate savings opportunities and long-term strategies for accelerating the innovation process and pipeline. For the near term, we developed scenarios based on available 'off the shelf' technologies and practices for achieving minimum energy consumption in lighting, standby power in electronics, and miscellaneous end-uses in the U.S. residential sector. In the business-as-usual (BAU) case, energy consumption continues to grow despite innovations at a current rate of 1.7 percent/year (Laitner, 2004). Nevertheless, the need for developing new energy supplies can be mitigated through the use of 'best current technologies' as the industry norm in 2025. Figure 1 (see URL below) shows this reduction in energy consumption and greenhouse gas emissions. The BAU model corresponds to the current rate of 'decarbonization' in the overall U.S. economy (Energy Information Administration, 2004). Over a twenty-year period, about 2 billion metric tons of carbon dioxide and 30 quads of primary fuel could be saved through the introduction of "best current technology" with the greatest reductions in the area of lighting technologies. In 2025, 1.5 quads of primary energy is saved with the breakdown in end-use electricity saved as follows: 113 TWh (0.39 quads), 70.8 TWh (0.24 quads), and 62 TWh (0.21 quads) for residential lighting, appliance standards, and standby power respectively. In addition, there is empirical evidence from specific technology sectors, from statewide programs in California, as well as on theoretical grounds (Laitner, 2004) that innovation and decarbonization rates of 3 to 5 percent/year have at times been, and could again be achieved. While such high rates of innovation do not usually sustain themselves for more than a few years, innovation rates higher than the current 1.7 percent/year are also explored in this study. Acknowledgement: Alliance to Save Energy (ASE) and Energy Foundation References: Energy Information Administration. "Annual Energy Outlook 2004." Washington, DC: U.S. Department of Energy, 2004. Hanson, Donald A. and Laitner, John A. "Skip". "An Integrated Analysis of Policies That Increase Investments in Advanced Energy-Efficient/Low-Carbon Technologies." Energy Economics, 2003. Laitner, J. A. "How far energy efficiency." 2004. Nadel, Steve. "Appliance and Equipment Efficiency Standards." Annual Reviews, 2002.

NREL's Energy-Saving Technology for Air Conditioning Cuts Peak Power Loads Without Using Harmful Refrigerants (Fact Sheet)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

2012-07-01

This fact sheet describes how the DEVAP air conditioner was invented, explains how the technology works, and why it won an R&D 100 Award. Desiccant-enhanced evaporative (DEVAP) air-conditioning will provide superior comfort for commercial buildings in any climate at a small fraction of the electricity costs of conventional air-conditioning equipment, releasing far less carbon dioxide and cutting costly peak electrical demand by an estimated 80%. Air conditioning currently consumes about 15% of the electricity generated in the United States and is a major contributor to peak electrical demand on hot summer days, which can lead to escalating power costs, brownouts,more » and rolling blackouts. DEVAP employs an innovative combination of air-cooling technologies to reduce energy use by up to 81%. DEVAP also shifts most of the energy needs to thermal energy sources, reducing annual electricity use by up to 90%. In doing so, DEVAP is estimated to cut peak electrical demand by nearly 80% in all climates. Widespread use of this cooling cycle would dramatically cut peak electrical loads throughout the country, saving billions of dollars in investments and operating costs for our nation's electrical utilities. Water is already used as a refrigerant in evaporative coolers, a common and widely used energy-saving technology for arid regions. The technology cools incoming hot, dry air by evaporating water into it. The energy absorbed by the water as it evaporates, known as the latent heat of vaporization, cools the air while humidifying it. However, evaporative coolers only function when the air is dry, and they deliver humid air that can lower the comfort level for building occupants. And even many dry climates like Phoenix, Arizona, have a humid season when evaporative cooling won't work well. DEVAP extends the applicability of evaporative cooling by first using a liquid desiccant-a water-absorbing material-to dry the air. The dry air is then passed to an indirect evaporative cooling stage, in which the incoming air is in thermal contact with a moistened surface that evaporates the water into a separate air stream. As the evaporation cools the moistened surface, it draws heat from the incoming air without adding humidity to it. A number of cooling cycles have been developed that employ indirect evaporative cooling, but DEVAP achieves a superior efficiency relative to its technological siblings.« less

U.S. Department of Energy’s Industrial Technology Program and Its Impacts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Weakley, Steven A.; Roop, Joseph M.

The U.S. Department of Energy’s Industrial Technologies Program (ITP) has been working with industry since 1976 to encourage the development and adoption of new, energy-efficient technologies. ITP has helped industry not only use energy and materials more efficiently but also improve environ-mental performance, product quality, and productivity. To help ITP determine the impacts of its pro-grams, Pacific Northwest National Laboratory (PNNL) periodically reviews and analyzes ITP pro-gram benefits. PNNL contacts vendors and users of ITP-sponsored technologies that have been commer-cialized, estimates the number of units that have penetrated the market, conducts engineering analyses to estimate energy savings from the newmore » technolo¬gies, and estimates air pollution and carbon emission reductions. This paper discusses the results of PNNL’s most recent review (conducted in 2009). From 1976-2008, the commercialized technologies from ITP’s research and development programs and other activities have cumulatively saved 9.27 quadrillion Btu, with a net cost savings of $63.91 billion.« less

U.S. Department of Energy’s Industrial Technology Program and Its Impacts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Weakley, Steven A.; Roop, Joseph M.

The U.S. Department of Energy’s Industrial Technologies Program (ITP) has been working with industry since 1976 to encourage the development and adoption of new, energy-efficient technologies. ITP has helped industry not only use energy and materials more efficiently but also improve environ-mental performance, product quality, and productivity. To help ITP determine the impacts of its pro-grams, Pacific Northwest National Laboratory (PNNL) periodically reviews and analyzes ITP pro-gram benefits. PNNL contacts vendors and users of ITP-sponsored technologies that have been commer-cialized, estimates the number of units that have penetrated the market, conducts engineering analyses to estimate energy savings from the newmore » technolo¬gies, and estimates air pollution and carbon emission reductions. This paper discusses the results of PNNL’s most recent review (conducted in 2008). From 1976-2007, the commercialized technologies from ITP’s research and development programs and other activities have cumulatively saved 6.17 quadrillion Btu, with a net cost savings of $63.0 billion.« less

U. S. Department of Energy (DOE) Industrial Programs and Their Impacts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Weakley, Steven A.; Roop, Joseph M.

The U.S. Department of Energy's Industrial Technologies Program (ITP) has been working with industry since 1976 to encourage the development and adoption of new, energy-efficient technologies. ITP has helped industry not only use energy and materials more efficiently but also improve environmental performance, product quality, and productivity. To help ITP determine the impacts of its programs, Pacific Northwest National Laboratory (PNNL) periodically reviews and analyzes ITP program benefits. PNNL contacts vendors and users of ITP-sponsored technologies that have been commercialized, estimates the number of units that have penetrated the market, conducts engineering analyses to estimate energy savings from the newmore » technologies, and estimates air pollution and carbon emission reductions. This paper discusses the results of the most recent PNNL review (conducted in 2003). From 1976-2002, the commercialized technologies from ITP's R&D programs and other activities have cumulatively saved 3.7 quadrillion Btu, with a net cost savings of $14.6 billion.« less

U.S. Department of Energy (DOE) Industrial Programs and Their Impacts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Weakley, Steven A.; Roop, Joseph M.

The U.S. Department of Energy’s Industrial Technologies Program (ITP) has been working with industry since 1976 to encourage the development and adoption of new, energy-efficient technologies. ITP has helped industry not only use energy and materials more efficiently but also improve environmental performance, product quality, and productivity. To help ITP determine the impacts of its programs, Pacific Northwest National Laboratory (PNNL) periodically reviews and analyzes ITP program benefits. PNNL contacts vendors and users of ITP-sponsored technologies that have been commercialized, estimates the number of units that have penetrated the market, conducts engineering analyses to estimate energy savings from the newmore » technologies, and estimates air pollution and carbon emission reductions. This paper discusses the results of the most recent PNNL review (conducted in 2005). From 1976-2004, the commercialized technologies from ITP’s research and development (R&D) programs and other activities have cumulatively saved 4.72 quadrillion Btu, with a net cost savings of $23.1 billion.« less

12 CFR 390.252 - How must separate corporate identities be maintained?

Code of Federal Regulations, 2014 CFR

2014-01-01

... 12 Banks and Banking 5 2014-01-01 2014-01-01 false How must separate corporate identities be maintained? 390.252 Section 390.252 Banks and Banking FEDERAL DEPOSIT INSURANCE CORPORATION REGULATIONS AND... Organizations § 390.252 How must separate corporate identities be maintained? (a) Each State savings association...

12 CFR 390.252 - How must separate corporate identities be maintained?

Code of Federal Regulations, 2012 CFR

2012-01-01

... 12 Banks and Banking 5 2012-01-01 2012-01-01 false How must separate corporate identities be maintained? 390.252 Section 390.252 Banks and Banking FEDERAL DEPOSIT INSURANCE CORPORATION REGULATIONS AND... Organizations § 390.252 How must separate corporate identities be maintained? (a) Each State savings association...

12 CFR 390.252 - How must separate corporate identities be maintained?

Code of Federal Regulations, 2013 CFR

2013-01-01

... 12 Banks and Banking 5 2013-01-01 2013-01-01 false How must separate corporate identities be maintained? 390.252 Section 390.252 Banks and Banking FEDERAL DEPOSIT INSURANCE CORPORATION REGULATIONS AND... Organizations § 390.252 How must separate corporate identities be maintained? (a) Each State savings association...

Improved components for engine fuel savings

NASA Technical Reports Server (NTRS)

Antl, R. J.; Mcaulay, J. E.

1980-01-01

NASA programs for developing fuel saving technology include the Engine Component Improvement Project for short term improvements in existing air engines. The Performance Improvement section is to define component technologies for improving fuel efficiency for CF6, JT9D and JT8D turbofan engines. Sixteen concepts were developed and nine were tested while four are already in use by airlines. If all sixteen concepts are successfully introduced the gain will be fuel savings of more than 6 billion gallons over the lifetime of the engines. The improvements include modifications in fans, mounts, exhaust nozzles, turbine clearance and turbine blades.

Bandwidth Study on Energy Use and Potential Energy Saving Opportunities in U.S. Pulp and Paper Manufacturing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sabine Brueske, Caroline Kramer, Aaron Fisher

2015-06-01

Energy bandwidth studies of U.S. manufacturing sectors can serve as foundational references in framing the range (or bandwidth) of potential energy savings opportunities. This bandwidth study examines energy consumption and potential energy savings opportunities in U.S. pulp and paper manufacturing. The study relies on multiple sources to estimate the energy used in six individual process areas, representing 52% of sector-wide energy consumption. Energy savings opportunities for individual processes are based on technologies currently in use or under development; the potential savings are then extrapolated to estimate sector-wide energy savings opportunity

Bandwidth Study on Energy Use and Potential Energy Savings Opportunities in U.S. Petroleum Refining

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sabine Brueske, Caroline Kramer, Aaron Fisher

2015-06-01

Energy bandwidth studies of U.S. manufacturing sectors can serve as foundational references in framing the range (or bandwidth) of potential energy savings opportunities. This bandwidth study examines energy consumption and potential energy savings opportunities in U.S. petroleum refining. The study relies on multiple sources to estimate the energy used in nine individual process areas, representing 68% of sector-wide energy consumption. Energy savings opportunities for individual processes are based on technologies currently in use or under development; these potential savings are then extrapolated to estimate sector-wide energy savings opportunity.

Energy Savings Potential and RD&D Opportunities for Commercial Building HVAC Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Goetzler, William; Shandross, Richard; Young, Jim

The Building Technologies Office (BTO) commissioned this characterization and technology assessment of heating, ventilation, and air-conditioning (HVAC) systems for commercial buildings. The main objectives of this study: Identify a wide range of technology options in varying stages of development that could reduce commercial HVAC energy consumption; Characterize these technology options based on their technical energy-savings potential, development status, non-energy benefits, and other factors affecting end-user acceptance and the ability to compete with conventional HVAC technologies; Make specific recommendations to DOE and other stakeholders on potential research, development, and demonstration (RD&D) activities that would support further development of the most promisingmore » technology options.« less

Survey of metallurgical recycling processes. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pemsler, J.P.

1979-03-01

In the year 2000, the US will consume about 3.2 x 10/sup 15/ Btu to produce the seven major nonferrous metals Al, Cu, Zn, Pb, Ni, Mg, and Ti. Of this amount, 82% will be used in the production of Al. It is projected that 0.6 x 10/sup 15/ Btu will be saved by the recycle of secondary metals. Major opportunities for increasing the extent of recycle and thereby increasing the energy savings are discussed. An inherent feature in the energistics of recycle is that physical processes such as magnetic separation, density separations, melting, and in some instances vaporization aremore » far less energy intensive than are chemical processes associated with dissolution and electrowinning. It is in the domain of scrap of complex composition and physical form, difficult to handle by existing technology, that opportunities exist for new chemical recycle technology. Recycle of scrap metal of adequate grade is currently achieved through pyrometallurgical processes which, in many cases, are not very energy intensive as compared with hydrometallurgical processes. Preliminary flowsheets are presented for the recovery of value metals from batteries considered for use in vehicular propulsion and load leveling applications. The battery types examined are lead/acid, nickel/zinc, nickel/iron, zinc/chlorine, lithium-aluminum/iron sulfide, and sodium/sulfur. A flow sheet has been outlined for an integrated hydrometallurgical process to treat low-grade copper scrap. A fully integrated hydrometallurgical process is outlined, and costs and energy consumption are derived, for recovering zinc metal from electric furnace flue dusts. Costs and energy are high and the process does not appear to warrant development at this time. Improvement in the recycle of magnesium is associated primarily with improved recycle in the Al industry where Mg is an important alloy additive. Ni and Ti recycle are associated with improved collection and sorting of stainless steel and specialty alloys.« less

Chapter 2: Commercial and Industrial Lighting Evaluation Protocol. The Uniform Methods Project: Methods for Determining Energy Efficiency Savings for Specific Measures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kurnik, Charles W; Gowans, Dakers; Telarico, Chad

The Commercial and Industrial Lighting Evaluation Protocol (the protocol) describes methods to account for gross energy savings resulting from the programmatic installation of efficient lighting equipment in large populations of commercial, industrial, and other nonresidential facilities. This protocol does not address savings resulting from changes in codes and standards, or from education and training activities. A separate Uniform Methods Project (UMP) protocol, Chapter 3: Commercial and Industrial Lighting Controls Evaluation Protocol, addresses methods for evaluating savings resulting from lighting control measures such as adding time clocks, tuning energy management system commands, and adding occupancy sensors.

Using economic benefits for recycling in a separate collection centre managed as a "reverse supermarket": a sociological survey.

PubMed

De Feo, Giovanni; Polito, Anna Rita

2015-04-01

Separate collection centres (SCCs), where citizens can deliver recyclable fractions of municipal solid waste (MSW), in an "urban mining" perspective, can be considered a sort of "reverse supermarket", where people can deliver their recyclables in order to either obtain a waste fee reduction or shopping vouchers. The latter is the case of Baronissi, a town of around 17,000 inhabitants in the Province of Salerno, in the Campania region of Italy. The principal aim of the study was to investigate by means of a sociological survey the relationship between citizens and the separate collection program, with particular emphasis on the role played by the SCC. The separate collection system was evaluated either good or very good by 95.8% of the sample, while 99.2% expressed a good or very good evaluation of the quality of the service inside the separate collection centre: SCC users acted as a community as highlighted by the negative response of the Chi-square test for independence. Respecting the environment prevailed over saving time, obtaining eco-points, or saving money as the main reason why people went to the SCC. The majority of the respondents agreed if only putrescibles and residue should be collected directly from their homes, while all the other materials should be collected exclusively at the SCC, allowing to save money for the management of the kerbside collection system with a consequent further waste fee reduction for the residents. Copyright © 2015 Elsevier Ltd. All rights reserved.

[Advances in studies on multi-stage countercurrent extraction technology in traditional Chinese medicine].

PubMed

Xie, Zhi-Peng; Liu, Xue-Song; Chen, Yong; Cai, Ming; Qu, Hai-Bin; Cheng, Yi-Yu

2007-05-01

Multi-stage countercurrent extraction technology, integrating solvent extraction, repercolation with dynamic and countercurrent extraction, is a novel extraction technology for the traditional Chinese medicine. This solvent-saving, energy-saving and high-extraction-efficiency technology can at the most drive active compounds to diffuse from the herbal materials into the solvent stage by stage by creating concentration differences between the herbal materials and the solvents. This paper reviewed the basic principle, the influence factors and the research progress and trends of the equipments and the application of the multi-stage countercurrent extraction.

77 FR 23373 - Small Business Investment Companies-Energy Saving Qualified Investments

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-19

... Debenture usage, number of Small Businesses financed, resulting breakthroughs in technology, comparative studies quantifying energy savings, and performance of Small Businesses financed. While SBA is concerned...

Explaining the differences in household food waste collection and treatment provisions between local authorities in England and Wales.

PubMed

Bees, A D; Williams, I D

2017-12-01

Separate household food waste collection for anaerobic digestion is one method used in the sustainable management of biodegradable municipal solid waste (MSW). Recycling of food waste contributes to the UK's reuse, recycling and composting targets and can help local authorities boost plateauing rates whilst encouraging landfill diversion. This study explored the reasons for differences in the provision of food waste collections, using two comparable local authorities, one with a collection in Wales (Cardiff), and the other absent of such service in England (Southampton). A PESTLE analysis investigated the political, economic, social, technological, legal and environmental impacts of separate food waste collections. The greenhouse gas impacts of the collection and treatment systems of MSW in both cities were estimated for 2012/13. Results showed significant policy and legislative differences between devolved governments, that separate food waste collections can save local authorities significant sums of money and substantially reduce greenhouse gas impacts. A survey of one hundred respondents in each city aimed to understand attitudes and behaviours towards recycling, food waste segregation, cooking and purchasing habits. The number of frequent recyclers and levels of satisfaction were higher in the authority which provided a separate food waste collection. In the area which lacked a separate collection service, over three-quarters of respondents would participate in such a scheme if it were available. Copyright © 2017 Elsevier Ltd. All rights reserved.

Energy Savings Potential and RD&D Opportunities for Non-Vapor-Compression HVAC Technologies

DOE Office of Scientific and Technical Information (OSTI.GOV)

none,

While vapor-compression technologies have served heating, ventilation, and air-conditioning (HVAC) needs very effectively, and have been the dominant HVAC technology for close to 100 years, the conventional refrigerants used in vapor-compression equipment contribute to global climate change when released to the atmosphere. This Building Technologies Office report: --Identifies alternatives to vapor-compression technology in residential and commercial HVAC applications --Characterizes these technologies based on their technical energy savings potential, development status, non-energy benefits, and other factors affecting end-user acceptance and their ability to compete with conventional vapor-compression systems --Makes specific research, development, and deployment (RD&D) recommendations to support further development ofmore » these technologies, should DOE choose to support non-vapor-compression technology further.« less

17 CFR 240.3a4-1 - Associated persons of an issuer deemed not to be brokers.

Code of Federal Regulations, 2011 CFR

2011-04-01

... investment company (or registered separate account); an insurance company; a bank; a savings and loan... trust for which a bank, a savings and loan association, a trust company, or a registered investment... the Investment Advisers Act of 1940 to an investment company registered under the Investment Company...

Energy-Saving Melting and Revert Reduction Technology (E-SMARRT): Final Summary Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

White, Thornton C

2014-03-31

Energy-Saving Melting and Revert Reduction Technology (E-SMARRT) is a balanced portfolio of R&D tasks that address energy-saving opportunities in the metalcasting industry. E-SMARRT was created to: • Improve important capabilities of castings • Reduce carbon footprint of the foundry industry • Develop new job opportunities in manufacturing • Significantly reduce metalcasting process energy consumption and includes R&D in the areas of: • Improvements in Melting Efficiency • Innovative Casting Processes for Yield Improvement/Revert Reduction • Instrumentation and Control Improvement • Material properties for Casting or Tooling Design Improvement The energy savings and process improvements developed under E-SMARRT have been mademore » possible through the unique collaborative structure of the E-SMARRT partnership. The E-SMARRT team consisted of DOE’s Office of Industrial Technology, the three leading metalcasting technical associations in the U.S: the American Foundry Society; the North American Die Casting Association; and the Steel Founders’ Society of America; and SCRA Applied R&D, doing business as the Advanced Technology Institute (ATI), a recognized leader in distributed technology management. This team provided collaborative leadership to a complex industry composed of approximately 2,000 companies, 80% of which employ less than 100 people, and only 4% of which employ more than 250 people. Without collaboration, these new processes and technologies that enable energy efficiencies and environment-friendly improvements would have been slow to develop and had trouble obtaining a broad application. The E-SMARRT R&D tasks featured low-threshold energy efficiency improvements that are attractive to the domestic industry because they do not require major capital investment. The results of this portfolio of projects are significantly reducing metalcasting process energy consumption while improving the important capabilities of metalcastings. Through June 2014, the E-SMARRT program predicts an average annual estimated savings of 59 Trillion BTUs per year over a 10 year period through Advanced Melting Efficiencies and Innovative Casting Processes. Along with these energy savings, an estimated average annual estimate of CO2 reduction per year over a ten year period is 3.56 Million Metric Tons of Carbon Equivalent (MM TCE).« less

Saving energy and reducing emissions of both polycyclic aromatic hydrocarbons and particulate matter by adding bio-solution to emulsified diesel.

PubMed

Lin, Yuan-Chung; Lee, Wen-Jhy; Chen, Chun-Chi; Chen, Chung-Bang

2006-09-01

Development of emulsified diesel has been driven by the need to reduce emissions from diesel engines and to save energy. Emulsification technology and bio-solution (NOE-7F) were used to produce emulsified diesel in this study. The experimental results indicated that there were no significant separation layers in W13 (13 wt % water + 87 wt % PDF), W16 (16 wt % water + 84 wt % PDF), W19 (19 wt % water + 81 wt % PDF), E13 (13 wt % NOE-7F water + 87 wt % PDF), E16 (16 wt % NOE-7F water + 83 wt % PDF), and E19 (19 wt % NOE-7F water + 81 wt % PDF) after premium diesel fuel (PDF) was emulsified for more than 30 days. In addition, there was no significant increase in damage from using these six emulsified fuels after the operation of the diesel generator for more than one year. The energy saving and reduction of particulate matter (PM) and total polycyclic aromatic hydrocarbons (PAHs) for W13, W16, W19, E13, E16 and E19, respectively, were 3.90%, 30.9%, 27.6%; 3.38%, 37.0%, 34.9%; 2.17%, 22.2%, 15.4%; 5.87%, 38.6%, 49.3%; 5.88%, 57.8%, 58.0%; and 4.75%, 31.1%, 47.3%, compared with PDF. The above results revealed that the bio-solution (NOE-7F) had a catalytic effect which elevated the combustion efficiency and decreased pollutant emissions during the combustion process. Furthermore, bio-solution (NOE-7F) can stabilize the emulsified fuels and enhance energy saving. Thus, emulsified fuels are highly suitable for use as alternative fuels. Due to the increasing price of diesel, emulsified diesel containing NOE-7F has potential for commercial application.

Use of Occupancy Sensors in LED Parking Lot and Garage Applications: Early Experiences

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kinzey, Bruce R.; Myer, Michael; Royer, Michael P.

2012-11-07

Occupancy sensor systems are gaining traction as an effective technological approach to reducing energy use in exterior commercial lighting applications. Done correctly, occupancy sensors can substantially enhance the savings from an already efficient lighting system. However, this technology is confronted by several potential challenges and pitfalls that can leave a significant amount of the prospective savings on the table. This report describes anecdotal experiences from field installations of occupancy sensor controlled light-emitting diode (LED) lighting at two parking structures and two parking lots. The relative levels of success at these installations reflect a marked range of potential outcomes: from anmore » additional 76% in energy savings to virtually no additional savings. Several issues that influenced savings were encountered in these early stage installations and are detailed in the report. Ultimately, care must be taken in the design, selection, and commissioning of a sensor-controlled lighting installation, else the only guaranteed result may be its cost.« less

Energy-Saving Opportunities for Manufacturing Companies, (English/Russian Fact Sheet) (Revised)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

This English/Russian brochure describes the Industrial Technologies Program Save Energy Now model and provides information on tools and resources to help manufacturing facilities reduce industrial energy intensity.

Energy-Saving Opportunities for Manufacturing Companies, International Fact Sheet (Spanish)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

This English/Spanish fact sheet describes the Industrial Technologies Program Save Energy Now model and provides information on tools and resources to help manufacturing facilities reduce industrial energy intensity.

Bandwidth Study on Energy Use and Potential Energy Saving Opportunities in U.S. Chemical Manufacturing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sabine Brueske, Caroline Kramer, Aaron Fisher

Energy bandwidth studies of U.S. manufacturing sectors can serve as foundational references in framing the range (or bandwidth) of potential energy savings opportunities. This bandwidth study examines energy consumption and potential energy savings opportunities in U.S. chemical manufacturing. The study relies on multiple sources to estimate the energy used in the production of 74 individual chemicals, representing 57% of sector-wide energy consumption. Energy savings opportunities for individual chemicals and for 15 subsectors of chemicals manufacturing are based on technologies currently in use or under development; these potential savings are then extrapolated to estimate sector-wide energy savings opportunity.

Hydrogen Selective Inorganic membranes for Gas Separations under High Pressure Intermediate Temperature Hydrocarbonic Envrionment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rich Ciora; Paul KT Liu

2012-06-27

In this project, we have successfully developed a full scale commercially ready carbon molecular sieve (CMS) based membrane for applications in H{sub 2} recovery from refinery waste and other aggressive gas streams. Field tests at a refinery pilot plant and a coal gasification facility have successfully demonstrated its ability to recovery hydrogen from hydrotreating and raw syngas respectively. High purity H{sub 2} and excellent stability of the membrane permeance and selectivity were obtained in testing conducted over >500 hours at each site. The results from these field tests as well as laboratory testing conclude that the membranes can be operated at high pressures (up to 1,000 psig) and temperatures (up to 300 C) in presence of aggressive contaminants, such as sulfur and nitrogen containing species (H{sub 2}S, CO{sub 2}, NH{sub 3}, etc), condensable hydrocarbons, tar-like species, heavy metals, etc. with no observable effect on membrane performance. By comparison, similar operating conditions and/or environments would rapidly destroy competing membranes, such as polymeric, palladium, zeolitic, etc. Significant cost savings can be achieved through recovering H{sub 2} from refinery waste gas using this newly developed CMS membrane. Annual savings ofmore » $$2 to 4MM/year (per 20,000 scfd of waste gas) can be realized by recovering the H{sub 2} for reuse (versus fuel). Projecting these values over the entire US market, potential H{sub 2} savings from refinery waste gases on the order of 750 to 1,000MM scfd and $$750 to $1,000MM per year are possible. In addition to the cost savings, potential energy savings are projected to be ca. 150 to 220 tBTU/yr and CO{sub 2} gas emission reductions are projected to be ca. 5,000 to 6,500MMtons/year. The full scale membrane bundle developed as part of this project, i.e., 85 x 30 inch ceramic membrane tubes packaged into a full ceramic potting, is an important accomplishment. No comparable commercial scale product exists in the inorganic membrane field. Further, this newly developed full scale bundle concept can be extended to other thin film inorganic membrane technology (Pd, zeolite, etc), providing a potential commercialization pathway for these membrane materials that demonstrate high potential in a variety of separation applications yet remain a laboratory 'novelty' for lack of a full scale support. Overall, the project has been highly successful and all of the project objectives have been met. We have developed the first of its kind commercial scale carbon molecular sieve membrane and demonstrated its performance in field testing under aggressive operating conditions and in the presence of chemical contaminants that would rapidly destroy alternative organic and inorganic membranes. This innovative membrane permits H{sub 2} recovery from gas streams that up until now have not been successfully treated with membrane or conventional technology. Our end user participant is currently pursuing the field demonstration of this membrane for hydrogen recovery at its refinery site.« less

Life cycle and economic assessment of source-separated MSW collection with regard to greenhouse gas emissions: a case study in China.

PubMed

Dong, Jun; Ni, Mingjiang; Chi, Yong; Zou, Daoan; Fu, Chao

2013-08-01

In China, the continuously increasing amount of municipal solid waste (MSW) has resulted in an urgent need for changing the current municipal solid waste management (MSWM) system based on mixed collection. A pilot program focusing on source-separated MSW collection was thus launched (2010) in Hangzhou, China, to lessen the related environmental loads. And greenhouse gas (GHG) emissions (Kyoto Protocol) are singled out in particular. This paper uses life cycle assessment modeling to evaluate the potential environmental improvement with regard to GHG emissions. The pre-existing MSWM system is assessed as baseline, while the source separation scenario is compared internally. Results show that 23 % GHG emissions can be decreased by source-separated collection compared with the base scenario. In addition, the use of composting and anaerobic digestion (AD) is suggested for further optimizing the management of food waste. 260.79, 82.21, and -86.21 thousand tonnes of GHG emissions are emitted from food waste landfill, composting, and AD, respectively, proving the emission reduction potential brought by advanced food waste treatment technologies. Realizing the fact, a modified MSWM system is proposed by taking AD as food waste substitution option, with additional 44 % GHG emissions saved than current source separation scenario. Moreover, a preliminary economic assessment is implemented. It is demonstrated that both source separation scenarios have a good cost reduction potential than mixed collection, with the proposed new system the most cost-effective one.

A Compendium of Energy Conservation: Success Stories 90

DOE R&D Accomplishments Database

1990-12-01

The Department of Energy's (DOE) Office of Conservation and Renewable Energy proudly presents this summary of some its most successful projects and activities. The projects included in this document have made significant contributions to improving energy efficiency and fuel flexibility in the United States. The energy savings that can be realized from these projects are considerable. Americans have shown an impressive ability to reduce energy consumption since 1973. Studies show that 34 quadrillion Btus (quads) of energy were saved in 1988 alone as a result of energy conservation and other factors. These savings, worth approximately $180 billion, represent more energy than the United States obtains from any other single source. The availability of new, energy-efficient technologies has been an important ingredient in achieving these savings. Federal efforts to develop and commercialize energy-saving technologies and processes are a part of the reason for this progress. Over the past 10 years, DOE has carefully invested more than $2 billion in hundreds of research and development (R&D) projects to ensure the availability of advanced technology in the marketplace. These energy-efficient projects are carried out through DOE's Office of Conservation and Renewable Energy and reflect opportunities in the three energy-consuming, end-use sectors of the economy: buildings, transportation, and industry.

Our Hidden Past: Peacetime

DOE Office of Scientific and Technical Information (OSTI.GOV)

Smith, Ray

Y-12 separated isotopes to win the war, then during the 1950s separated isotopes to save lives. Y-12's calutrons were used for a peacetime mission in the stable isotope program. Y-12 provided stable isotopes for research in medicine, agriculture, industry and biology.

Our Hidden Past: Peacetime

ScienceCinema

Smith, Ray

2018-06-04

Y-12 separated isotopes to win the war, then during the 1950s separated isotopes to save lives. Y-12's calutrons were used for a peacetime mission in the stable isotope program. Y-12 provided stable isotopes for research in medicine, agriculture, industry and biology.

Pollution prevention as a market-enhancing strategy: a storehouse of economical and environmental opportunities.

PubMed Central

Hoffman, J S

1992-01-01

EPA's (Environmental Protection Agency) Green Lights Program for energy-efficient lighting illustrates the economic benefits and the market-transforming value of a pollution prevention philosophy. Using technologies available today, and assuming current prices, this program is expected to reduce air pollution 5%, while saving the nation's businesses up to 20 billion in electric bills every year. However, these pollution prevention and savings estimates may be low. As Green Lights transforms the market for lighting services by creating a higher demand for better technologies at lower costs, the program will likely achieve even larger pollution reductions and electricity savings. PMID:11607262

The membrane separation mechanism in protein concentration from the extract of waste press cake in biofuel manufacturing process of Jatropha seeds

NASA Astrophysics Data System (ADS)

Chung, T. W.; Chen, C. K.; Hsu, S. H.

2017-11-01

Protein concentration process using filter membrane has a significant advantage on energy saving compared to the traditional drying processes. However, fouling on large membrane area and frequent membrane cleaning will increase the energy consumption and operation cost for the protein concentration process with filter membrane. In this study, the membrane filtration for protein concentration will be conducted and compared with the recent protein concentration technology. The analysis of operating factors for protein concentration process using filter membrane was discussed. The separation mechanism of membrane filtration was developed according to the size difference between the pore of membrane and the particle of filter material. The Darcy’s Law was applied to discuss the interaction on flux, TMP (transmembrane pressure) and resistance in this study. The effect of membrane pore size, pH value and TMP on the steady-state flux (Jst) and protein rejection (R) were studied. It is observed that the Jst increases with decreasing membrane pore size, the Jst increases with increasing TMP, and R increased with decreasing solution pH value. Compare to other variables, the pH value is the most significant variable for separation between protein and water.

Energy-Saving Opportunities for Manufacturing Companies (English/Portuguese Brochure) (in English/Portuguese)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

This English/Portuguese brochure describes the Industrial Technologies Program Save Energy Now model and provides information on tools and resources to help manufacturing facilities reduce industrial energy intensity.

Dynamic modeling of potentially conflicting energy reduction strategies for residential structures in semi-arid climates.

PubMed

Hester, Nathan; Li, Ke; Schramski, John R; Crittenden, John

2012-04-30

Globally, residential energy consumption continues to rise due to a variety of trends such as increasing access to modern appliances, overall population growth, and the overall increase of electricity distribution. Currently, residential energy consumption accounts for approximately one-fifth of total U.S. energy consumption. This research analyzes the effectiveness of a range of energy-saving measures for residential houses in semi-arid climates. These energy-saving measures include: structural insulated panels (SIP) for exterior wall construction, daylight control, increased window area, efficient window glass suitable for the local weather, and several combinations of these. Our model determined that energy consumption is reduced by up to 6.1% when multiple energy savings technologies are combined. In addition, pre-construction technologies (structural insulated panels (SIPs), daylight control, and increased window area) provide roughly 4 times the energy savings when compared to post-construction technologies (window blinds and efficient window glass). The model also illuminated the importance variations in local climate and building configuration; highlighting the site-specific nature of this type of energy consumption quantification for policy and building code considerations. Published by Elsevier Ltd.

Reducing Weight for Transportation Applications: Technology Challenges and Opportunities

NASA Astrophysics Data System (ADS)

Taub, Alan I.

Today's land, sea and air transportation industries — as a business necessity — are focused on technology solutions that will make vehicles more sustainable in terms of energy, the environment, safety and affordability. Reducing vehicle weight is a key enabler for meeting these challenges as well as increasing payload and improving performance. The potential weight reductions from substituting lightweight metals (advanced high-strength steels, aluminum, magnesium and titanium alloys) are well established. For magnesium castings, weight savings of 60% have been reported [1]. The value of weight reduction depends on the transportation sector and ranges from about 5/kg saved for automobiles to over 500/kg saved for aircraft [2]. The challenge is to optimize the material properties and develop robust, high volume, manufacturing technologies and the associated supply chain to fabricate components and subsystems at the appropriate cost for each application.

The financial impact of robotic technology for partial and radical nephrectomy.

PubMed

Kates, Max; Ball, Mark W; Patel, Hiten D; Gorin, Michael A; Pierorazio, Phillip M; Allaf, Mohamad E

2015-03-01

We sought to evaluate the financial impact of robotic technology for partial nephrectomy (PN) and radical nephrectomy (RN) in the state of Maryland. The Maryland Health Services Cost Review Commission (HSCRC) documents all acute care hospital charges data. This database was queried for patients who underwent laparoscopic or robot-assisted RN and PN from 2008 to 2012. Total hospital charge, subcharge, and length of stay (LOS) were analyzed separately for RN and PN. Overall, 2834 patients were identified. Of those, 282 were laparoscopic PN (LPN), 1078 robot-assisted PN (RPN), 1098 laparoscopic RN (LRN), and 376 robot-assisted RN (RRN). For PN, the total hospital charge was $19,062 for LPN and $18,255 for RPN (P=0.138), with a charge savings of $807 per case in favor of robotics. For RN, the total hospital charge was $23,391 for RRN and $18,280 for LRN (P=0.004), with a charge premium of $5111 for robotic cases. LOS was shorter for RPN compared with LPN (2.51 vs 2.99 days, P<0.0001) and for RRN compared with LRN (3.52 vs 3.98, P=0.0498). RPN is associated with lower hospital charges than LPN, while RRN is associated with higher hospital charges than LRN. Savings for RPN are driven by decreased room and board charge, while the premium for RRN is driven by higher operating room and supply charges. Because RRN use is increasing, the financial implications of RRN use for routine cases warrants further study.

Quantifying the benefits of a building retrofit using an integrated system approach: A case study

DOE PAGES

Regnier, Cynthia; Sun, Kaiyu; Hong, Tianzhen; ...

2017-11-11

Building retrofits provide a large opportunity to significantly reduce energy consumption in the buildings sector. Traditional building retrofits focus on equipment upgrades, often at the end of equipment life or failure, and result in replacement with marginally improved similar technology and limited energy savings. The Integrated System (IS) retrofit approach enables much greater energy savings by leveraging interactive effects between end use systems, enabling downsized or lower energy technologies. This work presents a case study in Hawaii quantifying the benefits of an IS retrofit approach compared to two traditional retrofit approaches: a Standard Practice of upgrading equipment to meet minimummore » code requirements, and an Improved Practice of upgrading equipment to a higher efficiency. The IS approach showed an energy savings of 84% over existing building energy use, much higher than the traditional approaches of 13% and 33%. The IS retrofit also demonstrated the greatest energy cost savings potential. While the degree of savings realized from the IS approach will vary by building and climate, these findings indicate that savings on the order of 50% and greater are not possible without an IS approach. It is therefore recommended that the IS approach be universally adopted to achieve deep energy savings.« less

Quantifying the benefits of a building retrofit using an integrated system approach: A case study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Regnier, Cynthia; Sun, Kaiyu; Hong, Tianzhen

Building retrofits provide a large opportunity to significantly reduce energy consumption in the buildings sector. Traditional building retrofits focus on equipment upgrades, often at the end of equipment life or failure, and result in replacement with marginally improved similar technology and limited energy savings. The Integrated System (IS) retrofit approach enables much greater energy savings by leveraging interactive effects between end use systems, enabling downsized or lower energy technologies. This work presents a case study in Hawaii quantifying the benefits of an IS retrofit approach compared to two traditional retrofit approaches: a Standard Practice of upgrading equipment to meet minimummore » code requirements, and an Improved Practice of upgrading equipment to a higher efficiency. The IS approach showed an energy savings of 84% over existing building energy use, much higher than the traditional approaches of 13% and 33%. The IS retrofit also demonstrated the greatest energy cost savings potential. While the degree of savings realized from the IS approach will vary by building and climate, these findings indicate that savings on the order of 50% and greater are not possible without an IS approach. It is therefore recommended that the IS approach be universally adopted to achieve deep energy savings.« less

Energy-saving technology of vector controlled induction motor based on the adaptive neuro-controller

NASA Astrophysics Data System (ADS)

Engel, E.; Kovalev, I. V.; Karandeev, D.

2015-10-01

The ongoing evolution of the power system towards a Smart Grid implies an important role of intelligent technologies, but poses strict requirements on their control schemes to preserve stability and controllability. This paper presents the adaptive neuro-controller for the vector control of induction motor within Smart Gird. The validity and effectiveness of the proposed energy-saving technology of vector controlled induction motor based on adaptive neuro-controller are verified by simulation results at different operating conditions over a wide speed range of induction motor.

An overview of flywheel technology for space applications

NASA Astrophysics Data System (ADS)

Decker, D. Kent; Spector, Victor A.; Pieronek, Thomas J.

1997-01-01

Recent developments in advanced composite flywheels using magnetic bearings has produced specific energies greater than 30 Whr/lb. These specific energy levels provide an opportunity for significant spacecraft weight savings compared to using nickel-hydrogen battery technology. Additional weight savings are possible if the flywheels are also used for momentum control. This paper explores the new challenges presented by application of flywheel technology to space power and attitude control subsystems. Issues with respect to mission application, safety and containment, launch environment, and combined power and attitude control operation are discussed.

An analysis of growth factors of rapeseed at modern resource-saving technology

NASA Astrophysics Data System (ADS)

Filipova, M.; Zheleva, I.; Sulejmenova, N.; Abildaev, E.

2017-10-01

Nowadays the production of rapeseed has grown due to the variety of existing possibilities for its using. This calls the search for new, resource-saving technologies for its growing in Republic of Kazakhstan. For these new technologies it is needed to know which are the factors that influence the production of rapeseed and how each factor influence the production and the quality of this culture. The careful study of these factors is necessary for better understudying the process of the growing aimed increasing the yields and quantity of the rapeseed.

Change in Land Use and Evapotranspiration in the Manas River Basin, China with Long-term Water-saving Measures.

PubMed

Yang, Guang; Xue, Lianqing; He, Xinlin; Wang, Cui; Long, Aihua

2017-12-19

Widespread application of water-saving measures, especially advanced drip irrigation technologies, may significantly impact on the land use, and further potentially alter regional ecological environments in an arid area. In this study, the remote sensing and geographic information system technology were used to analyze the LANDSAT images (1976-2015) and the MOD16 evapotranspiration data (2000-2015) in the Manas River Basin (MRB), China where the water-saving technologies have experienced the past 40 years. Our results show that the area of the cultivated land was approximately doubled from 1976 to 2015 with a dynamic degree of cultivated land ranging from 1.7% to 4%. The reclamation rates were estimated at 9.5% in 1976 and 21.8% in 2015 and the comprehensive index of land use degree shows an increasing trend in the MRB. The evapotranspiration in the MRB suggests that the cultivated land is becoming more humid while the other regions are becoming more arid. Long-term change in the land use is mainly promoted due to the multiple years' efforts on development of the water-saving technologies. This study greatly improves our understanding of the interactions between change in ecological environments and human activities and may provide policy makers guidance of sustainable development at an arid area.

Optimization of the oxidant supply system for combined cycle MHD power plants

NASA Technical Reports Server (NTRS)

Juhasz, A. J.

1982-01-01

An in-depth study was conducted to determine what, if any, improvements could be made on the oxidant supply system for combined cycle MHD power plants which could be reflected in higher thermal efficiency and a reduction in the cost of electricity, COE. A systematic analysis of air separation process varitions which showed that the specific energy consumption could be minimized when the product stream oxygen concentration is about 70 mole percent was conducted. The use of advanced air compressors, having variable speed and guide vane position control, results in additional power savings. The study also led to the conceptual design of a new air separation process, sized for a 500 MW sub e MHD plant, referred to a internal compression is discussed. In addition to its lower overall energy consumption, potential capital cost savings were identified for air separation plants using this process when constructed in a single large air separation train rather than multiple parallel trains, typical of conventional practice.

Energy Savings Potential and Research, Development, & Demonstration Opportunities for Commercial Building Heating, Ventilation, and Air Conditioning Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

none,

2011-09-01

This report covers an assessment of 182 different heating, ventilation, and air-conditioning (HVAC) technologies for U.S. commercial buildings to identify and provide analysis on 17 priority technology options in various stages of development. The analyses include an estimation of technical energy-savings potential, description of technical maturity, description of non-energy benefits, description of current barriers for market adoption, and description of the technology’s applicability to different building or HVAC equipment types. From these technology descriptions, are suggestions for potential research, development and demonstration (RD&D) initiatives that would support further development of the priority technology options.

How maya women respond to changing technology : The effect of helping behavior on initiating reproduction.

PubMed

Kramer, K L; McMillan, G P

1998-06-01

In the mid 1970s labor-saving technology was introduced into a Maya subsistence agricultural community that markedly increased the efficiency with which maize could be ground and water collected. This increased efficiency introduces a possible savings in the time that women allocate to work, which can be reapportioned to child care, food production, domestic work, or leisure. An earlier study suggested that this labor-saving technology had a positive effect in decreasing the age at which these Maya women begin their reproductive careers. Although there is a statistical association between the age at which women bear their first child and the introduction of modern technology, this association does not demonstrate that the decline in age at first birth is causally related to the presence of technology. This paper pursues two objectives to evaluate this potential causal relationship in greater detail. First, a theory relating technological change to the initiation of a reproductive career is briefly developed in order to make qualitative predictions about behavioral changes as a response to changing technology. Second, these predictions are then tested against time allocation data recently collected in this same Maya community.We suggest that both of the conditions necessary to initiate reproduction-fecundity and access to mates-fundamentally depend on the amount of help that a girl provides to her family. Further, the help that a girl provides can be affected by technological changes. Analyses show that when modern technology is available, unmarried young women do not change the time allocated to domestic tasks and child care, and allocate more time to low-energy leisure activities. This lack of perceived benefit to working more and a potential concomitant shift towards a positive energy balance may in part explain why Maya women leave home and initiate reproduction at a younger age after labor-saving technology is introduced.

Looking at IT through a New Lens: Achieving Cost Savings in a Fiscally Challenging Time

ERIC Educational Resources Information Center

Claffey, George F., Jr.

2009-01-01

Information technology (IT) departments must cut costs and justify expenditures in the face of shrinking budgets. To promote greater cost savings, it is important to look at IT through a new "lens." This article discusses four broad categories that can be evaluated to determine if IT resource alignment is appropriate and if savings can…

Future perspectives of using hollow fibers as structured packings in light hydrocarbon distillation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yang, Dali; Orler, Bruce; Tornga, Stephanie

2011-01-26

Olefin and paraffin are the largest chemical commodities. Furthermore, they are major building blocks for the petrochemical industry. Each year, petroleum refining, consumes 4,500 TBtu/yr in separation energy, making it one of the most energy-intensive industries in the United States). Just considering liquefied petroleum gas (ethane/propane/butane) and olefins (ethylene and propylene) alone, the distillation energy consumption is about 400 TBtu/yr in the US. Since petroleum distillation is a mature technology, incremental improvements in column/tray design will only provide a few percent improvements in the performance. However, each percent saving in net energy use amounts to savings of 10 TBtu/yr andmore » reduces CO{sub 2} emissions by 0.2 MTon/yr. In practice, distillation columns require 100 to 200 trays to achieve the desired separation. The height of a transfer unit (HTU) of conventional packings is typical in the range of 36-60 inch. Since 2006, we had explored using several non-selective membranes as the structured packings to replace the conventional packing materials used in propane and propylene distillation. We obtained the lowest HTU of < 8 inch for the hollow fiber column, which was >5 times shorter than that of the conventional packing materials. In 2008, we also investigated this type of packing materials in iso-/n-butane distillation. Because of a slightly larger relative volatility of iso-/n-butane than that of propane/propylene, a wider and a more stable operational range was obtained for the iso-/n-butane pair. However, all of the experiments were conducted on a small scale with flowrate of < 25 gram/min. Recently, we demonstrated this technology on a larger scale (<250 gram/min). Within the loading range of F-factor < 2.2 Pa{sup 0.5}, a pressure drop on the vapor side is below 50 mbar/m, which suggests that the pressure drop of hollow fibers packings is not an engineering barrier for the applications in distillations. The thermal stability study suggests that polypropylene hollow fibers are stable after a long time exposure to C{sub 2} - C{sub 4} mixtures. The effects of packing density on the separation efficiency will be discussed.« less

Effects of UAV Supervisory Control on F-18 Formation Flight Performance in a Simulator Environment

DTIC Science & Technology

2013-03-01

words) Continual advances in technology, along with increased cockpit workload— particularly the shift from two- seat to single- seat fighters to save...INTENTIONALLY LEFT BLANK v ABSTRACT Continual advances in technology, along with increased cockpit workload— particularly the shift from two- seat to...single- seat fighters to save money and reduce risk to life—push the limits of human mental capacity. Additionally, there is interest within the

Cogeneration Technology Alternatives Study (CTAS). Volume 1: Summary

NASA Technical Reports Server (NTRS)

Barna, G. J.; Burns, R. K.; Sagerman, G. D.

1980-01-01

Various advanced energy conversion systems that can use coal or coal-derived fuels for industrial cogeneration applications were compared to provide information needed by DOE to establish research and development funding priorities for advanced-technology systems that could significantly advance the use of coal or coal-derived fuels in industrial cogeneration. Steam turbines, diesel engines, open-cycle gas turbines, combined cycles, closed-cycle gas turbines, Stirling engines, phosphoric acid fuel cells, molten carbonate fuel cells, and thermionics were studied with technology advancements appropriate for the 1985-2000 time period. The various advanced systems were compared and evaluated for wide diversity of representative industrial plants on the basis of fuel energy savings, annual energy cost savings, emissions savings, and rate of return on investment as compared with purchasing electricity from a utility and providing process heat with an on-site boiler. Also included in the comparisons and evaluations are results extrapolated to the national level.

Cogeneration Technology Alternatives Study (CTAS). Volume 2: Comparison and evaluation of results

NASA Technical Reports Server (NTRS)

1984-01-01

CTAS compared and evaluated various advanced energy conversion systems that can use coal or coal-derived fuels for industrial cogeneration applications. The principal aim of the study was to provide information needed by DOE to establish research and development (R&D) funding priorities for advanced-technology systems that could significantly advance the use of coal or coal-derived fuels in industrial cogeneration. Steam turbines, diesel engines, open-cycle gas turbines, combined cycles, closed-cycle gas turbines, Stirling engines, phosphoric acid fuel cells, molten carbonate fuel cells, and thermionics were studied with technology advancements appropriate for the 1985-2000 time period. The various advanced systems were compared and evaluated for a wide diversity of representative industrial plants on the basis of fuel energy savings, annual energy cost savings, emissions savings, and rate of return on investment (ROI) as compared with purchasing electricity from a utility and providing process heat with an on-site boiler.

Advanced Measurement Systems Available to PIWG Members

NASA Technical Reports Server (NTRS)

Anderson, Robert; Lei, Jih-Fen (Technical Monitor)

2002-01-01

It was developed advanced measurement technologies to meet NASA goals: reduce design cycle time, reduce emission, reduce testing time, increase safety. The technology are saving money. This technology are available now for technology transfer: optical diagnostics, the film technology and MEMS devices.

Design and evaluation of Continuous Descent Approach as a fuel-saving procedure

NASA Astrophysics Data System (ADS)

Jin, Li

Continuous Descent Approach (CDA), which is among the key concepts of the Next Generation Air Transportation System (NextGen), is a fuel economical procedure, but requires increased separation to accommodate spacing uncertainties among arriving aircraft. Such negative impact is often overlooked when benefits are estimated. Although a considerable number of researches have been devoted to the estimation of potential fuel saving of CDA, few have attempted to explain the fuel saving observed in field tests from an analytical point of view. This research gives insights into the reasons why CDA saves fuel, and a number of design guidelines for CDA procedures are derived. The analytical relationship between speed, altitude, and time-cumulative fuel consumption is derived based on Base of Aircraft Data (BADA) Total Energy Model. Theoretical analysis implies that speed profile has an impact as substantial as, if not more than, vertical profile on the fuel consumption in the terminal area. In addition, CDA is not intrinsically a fuel-saving procedure: whether CDA saves fuel or not is contingent upon whether the speed profile is properly designed or not. Based on this model, the potential fuel savings due to CDA at San Francisco International Airport were estimated, and the accuracy of this estimation is analyzed. Possible uncertainties in this fuel estimation primarily resulted from the modeled CDA procedure and the inaccuracy of BADA. This thesis also investigates the fuel savings due to CDAs under high traffic conditions, counting not only the savings benefiting from optimal vertical profiles but also the extra fuel burn resulting from the increased separations. The simulated CDAs traffic is based on radar track data, and deconflicted by a scheduling algorithm that targets minimized delays. The delays are absorbed by speed change and path stretching, accounting for the air traffic controls that are entailed by CDAs. The fuel burn statistics calculated based on the BADA Total Energy Model reveals that the CDAs save on average 171.87 kg per arrival, but the number is discounted by delay absorption. The savings diminish as the arrival demand increases, and could be even negative due to large delays. The throughput analysis demonstrated that the impact of CDA on airport capacity is insignificant and tolerable. The Atlanta International Airport was used as the testbed for sensitivity analysis, and the New York Metroplex was used as the test bed for throughput analysis.

When energy saving advice leads to more, rather than less, consumption

NASA Astrophysics Data System (ADS)

Revell, Kirsten M. A.; Stanton, Neville A.

2017-01-01

Energy saving technology that relies on behaviour change fails to deliver on its promise. Energy saving advice also has limited effect. This paper examines and reveals how technology and energy saving advice interacts with householders' thought processes to influence energy consumption. A case study of three households that held a 'Feedback' mental model of the home heating thermostat, as defined by Kempton [1986. 'Two Theories of Home Heat Control'. Cognitive Science 10 (1): 75-90], was undertaken to understand the driver behind differences in their home heating strategies, and the effect on energy consumption. Analysis was undertaken from five different data sources comprising: (1) boiler on durations, (2) thermostat set point adjustments, (3) self-reported strategies with home heating controls, (4) user mental model descriptions of the home heating system, and (5) Interview transcripts. The authors found that differences in user mental models of home heating at the system level explained differences in the strategies chosen at the control device level. Differences in boiler on periods were found to relate to limitations of the 'Feedback' mental model; that is, the model fails to consider the effect of the movement of warm air within the home and the impact of internal/external temperature differentials on heat loss rates. The authors argue that technology and advice should be tailored to the thought processes adopted by householders in order to promote behaviour that would realise intended energy savings.

Products from NASA's In-Space Propulsion Technology Program Applicable to Low-Cost Planetary Missions

NASA Technical Reports Server (NTRS)

Anderson, David J.; Pencil, Eric; Vento, Daniel; Peterson, Todd; Dankanich, John; Hahne, David; Munk, Michelle M.

2011-01-01

Since September 2001 NASA s In-Space Propulsion Technology (ISPT) program has been developing technologies for lowering the cost of planetary science missions. Recently completed is the high-temperature Advanced Material Bipropellant Rocket (AMBR) engine providing higher performance for lower cost. Two other cost saving technologies nearing completion are the NEXT ion thruster and the Aerocapture technology project. Also under development are several technologies for low cost sample return missions. These include a low cost Hall effect thruster (HIVHAC) which will be completed in 2011, light weight propellant tanks, and a Multi-Mission Earth Entry Vehicle (MMEEV). This paper will discuss the status of the technology development, the cost savings or performance benefits, and applicability of these in-space propulsion technologies to NASA s future Discovery, and New Frontiers missions, as well as their relevance for sample return missions.

Space system production cost benefits from contemporary philosophies in management and manufacturing

NASA Technical Reports Server (NTRS)

Rosmait, Russell L.

1991-01-01

The cost of manufacturing space system hardware has always been expensive. The Engineering Cost Group of the Program Planning office at Marshall is attempting to account for cost savings that result from new technologies in manufacturing and management. The objective is to identify and define contemporary philosophies in manufacturing and management. The seven broad categories that make up the areas where technological advances can assist in reducing space system costs are illustrated. Included within these broad categories is a list of the processes or techniques that specifically provide the cost savings within todays design, test, production and operations environments. The processes and techniques listed achieve savings in the following manner: increased productivity; reduced down time; reduced scrap; reduced rework; reduced man hours; and reduced material costs. In addition, it should be noted that cost savings from production and processing improvements effect 20 to 40 pct. of production costs whereas savings from management improvements effects 60 to 80 of production cost. This is important because most efforts in reducing costs are spent trying to reduce cost in the production.

12 CFR 559.10 - How must separate corporate identities be maintained?

Code of Federal Regulations, 2010 CFR

2010-01-01

... 12 Banks and Banking 5 2010-01-01 2010-01-01 false How must separate corporate identities be maintained? 559.10 Section 559.10 Banks and Banking OFFICE OF THRIFT SUPERVISION, DEPARTMENT OF THE TREASURY... corporate identities be maintained? (a) Each savings association and subordinate organization thereof must...

12 CFR 559.10 - How must separate corporate identities be maintained?

Code of Federal Regulations, 2013 CFR

2013-01-01

... 12 Banks and Banking 6 2013-01-01 2012-01-01 true How must separate corporate identities be maintained? 559.10 Section 559.10 Banks and Banking OFFICE OF THRIFT SUPERVISION, DEPARTMENT OF THE TREASURY... corporate identities be maintained? (a) Each savings association and subordinate organization thereof must...

12 CFR 559.10 - How must separate corporate identities be maintained?

Code of Federal Regulations, 2014 CFR

2014-01-01

... 12 Banks and Banking 6 2014-01-01 2012-01-01 true How must separate corporate identities be maintained? 559.10 Section 559.10 Banks and Banking OFFICE OF THRIFT SUPERVISION, DEPARTMENT OF THE TREASURY... corporate identities be maintained? (a) Each savings association and subordinate organization thereof must...

12 CFR 559.10 - How must separate corporate identities be maintained?

Code of Federal Regulations, 2012 CFR

2012-01-01

... 12 Banks and Banking 6 2012-01-01 2012-01-01 false How must separate corporate identities be maintained? 559.10 Section 559.10 Banks and Banking OFFICE OF THRIFT SUPERVISION, DEPARTMENT OF THE TREASURY... corporate identities be maintained? (a) Each savings association and subordinate organization thereof must...

12 CFR 559.10 - How must separate corporate identities be maintained?

Code of Federal Regulations, 2011 CFR

2011-01-01

... 12 Banks and Banking 5 2011-01-01 2011-01-01 false How must separate corporate identities be maintained? 559.10 Section 559.10 Banks and Banking OFFICE OF THRIFT SUPERVISION, DEPARTMENT OF THE TREASURY... corporate identities be maintained? (a) Each savings association and subordinate organization thereof must...

Evaluation of Composite Structures Technologies for Application to NASA's Vision for Space Exploration (CoSTS)

NASA Technical Reports Server (NTRS)

Deo, Ravi; Wang, Donny; Bohlen, Jim; Fukuda, Cliff

2008-01-01

A trade study was conducted to determine the suitability of composite structures for weight and life cycle cost savings in primary and secondary structural systems for crew exploration vehicles, crew and cargo launch vehicles, landers, rovers, and habitats. The results of the trade study were used to identify and rank order composite material technologies that can have a near-term impact on a broad range of exploration mission applications. This report recommends technologies that should be developed to enable usage of composites on Vision for Space Exploration vehicles towards mass and life-cycle cost savings.

The aluminum smelting process.

PubMed

Kvande, Halvor

2014-05-01

This introduction to the industrial primary aluminum production process presents a short description of the electrolytic reduction technology, the history of aluminum, and the importance of this metal and its production process to modern society. Aluminum's special qualities have enabled advances in technologies coupled with energy and cost savings. Aircraft capabilities have been greatly enhanced, and increases in size and capacity are made possible by advances in aluminum technology. The metal's flexibility for shaping and extruding has led to architectural advances in energy-saving building construction. The high strength-to-weight ratio has meant a substantial reduction in energy consumption for trucks and other vehicles. The aluminum industry is therefore a pivotal one for ecological sustainability and strategic for technological development.

The Aluminum Smelting Process

PubMed Central

2014-01-01

This introduction to the industrial primary aluminum production process presents a short description of the electrolytic reduction technology, the history of aluminum, and the importance of this metal and its production process to modern society. Aluminum's special qualities have enabled advances in technologies coupled with energy and cost savings. Aircraft capabilities have been greatly enhanced, and increases in size and capacity are made possible by advances in aluminum technology. The metal's flexibility for shaping and extruding has led to architectural advances in energy-saving building construction. The high strength-to-weight ratio has meant a substantial reduction in energy consumption for trucks and other vehicles. The aluminum industry is therefore a pivotal one for ecological sustainability and strategic for technological development. PMID:24806722

Saving-enhanced memory: the benefits of saving on the learning and remembering of new information.

PubMed

Storm, Benjamin C; Stone, Sean M

2015-02-01

With the continued integration of technology into people's lives, saving digital information has become an everyday facet of human behavior. In the present research, we examined the consequences of saving certain information on the ability to learn and remember other information. Results from three experiments showed that saving one file before studying a new file significantly improved memory for the contents of the new file. Notably, this effect was not observed when the saving process was deemed unreliable or when the contents of the to-be-saved file were not substantial enough to interfere with memory for the new file. These results suggest that saving provides a means to strategically off-load memory onto the environment in order to reduce the extent to which currently unneeded to-be-remembered information interferes with the learning and remembering of other information. © The Author(s) 2014.

Preliminary Weight Savings Estimate for a Commercial Transport Wing Using Rod-Stiffened Stitched Composite Technology

NASA Technical Reports Server (NTRS)

Lovejoy, Andrew E.

2015-01-01

A structural concept called pultruded rod stitched efficient unitized structure (PRSEUS) was developed by the Boeing Company to address the complex structural design aspects associated with a pressurized hybrid wing body (HWB) aircraft configuration. While PRSEUS was an enabling technology for the pressurized HWB structure, limited investigation of PRSEUS for other aircraft structures, such as circular fuselages and wings, has been done. Therefore, a study was undertaken to investigate the potential weight savings afforded by using the PRSEUS concept for a commercial transport wing. The study applied PRSEUS to the Advanced Subsonic Technology (AST) Program composite semi-span test article, which was sized using three load cases. The initial PRSEUS design was developed by matching cross-sectional stiffnesses for each stringer/skin combination within the wing covers, then the design was modified to ensure that the PRSEUS design satisfied the design criteria. It was found that the PRSEUS wing design exhibited weight savings over the blade-stiffened composite AST Program wing of nearly 9%, and a weight savings of 49% and 29% for the lower and upper covers, respectively, compared to an equivalent metallic wing.

Closest Multi-Spacecraft Flying Formation on This Week @NASA – September 23, 2016

NASA Image and Video Library

2016-09-23

The four spacecraft orbiting Earth in formation as part of NASA’s Magnetospheric Multiscale, or MMS, mission achieved a new record recently when the space between them was decreased from just over six miles to only four-and-a-half miles. This is the closest separation ever of any multi-spacecraft formation. The team of spacecraft fly in a pyramid shape, called a tetrahedron, which enables MMS to capture three-dimensional observations of magnetic reconnection – a mysterious phenomenon, during which magnetic fields experience explosive interactions. The closer formation will allow the spacecraft to measure magnetic reconnection at smaller scales, helping scientists to better understand it. Also, Destination Mars Exhibit, Orbital ATK Targets Launch Window, NASA-developed Technology Saves Pilot’s Life, and Combined Federal Campaign Underway!

Core-Shell Columns in High-Performance Liquid Chromatography: Food Analysis Applications

PubMed Central

Preti, Raffaella

2016-01-01

The increased separation efficiency provided by the new technology of column packed with core-shell particles in high-performance liquid chromatography (HPLC) has resulted in their widespread diffusion in several analytical fields: from pharmaceutical, biological, environmental, and toxicological. The present paper presents their most recent applications in food analysis. Their use has proved to be particularly advantageous for the determination of compounds at trace levels or when a large amount of samples must be analyzed fast using reliable and solvent-saving apparatus. The literature hereby described shows how the outstanding performances provided by core-shell particles column on a traditional HPLC instruments are comparable to those obtained with a costly UHPLC instrumentation, making this novel column a promising key tool in food analysis. PMID:27143972

Status of not-in-kind refrigeration technologies for household space conditioning, water heating and food refrigeration

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bansal, Pradeep; Vineyard, Edward Allan; Abdelaziz, Omar

This paper presents a review of the next generation not-in-kind technologies to replace conventional vapor compression refrigeration technology for household applications. Such technologies are sought to provide energy savings or other environmental benefits for space conditioning, water heating and refrigeration for domestic use. These alternative technologies include: thermoacoustic refrigeration, thermoelectric refrigeration, thermotunneling, magnetic refrigeration, Stirling cycle refrigeration, pulse tube refrigeration, Malone cycle refrigeration, absorption refrigeration, adsorption refrigeration, and compressor driven metal hydride heat pumps. Furthermore, heat pump water heating and integrated heat pump systems are also discussed due to their significant energy saving potential for water heating and space conditioningmore » in households. The paper provides a snapshot of the future R&D needs for each of the technologies along with the associated barriers. Both thermoelectric and magnetic technologies look relatively attractive due to recent developments in the materials and prototypes being manufactured.« less

Using learning curves on energy-efficient technologies to estimate future energy savings and emission reduction potentials in the U.S. iron and steel industry

DOE Office of Scientific and Technical Information (OSTI.GOV)

Karali, Nihan; Park, Won Young; McNeil, Michael A.

Increasing concerns on non-sustainable energy use and climate change spur a growing research interest in energy efficiency potentials in various critical areas such as industrial production. This paper focuses on learning curve aspects of energy efficiency measures in the U.S iron and steel sector. A number of early-stage efficient technologies (i.e., emerging or demonstration technologies) are technically feasible and have the potential to make a significant contribution to energy saving and CO 2 emissions reduction, but fall short economically to be included. However, they may also have the cost effective potential for significant cost reduction and/or performance improvement in themore » future under learning effects such as ‘learning-by-doing’. The investigation is carried out using ISEEM, a technology oriented, linear optimization model. We investigated how steel demand is balanced with/without the availability learning curve, compared to a Reference scenario. The retrofit (or investment in some cases) costs of energy efficient technologies decline in the scenario where learning curve is applied. The analysis also addresses market penetration of energy efficient technologies, energy saving, and CO 2 emissions in the U.S. iron and steel sector with/without learning impact. Accordingly, the study helps those who use energy models better manage the price barriers preventing unrealistic diffusion of energy-efficiency technologies, better understand the market and learning system involved, predict future achievable learning rates more accurately, and project future savings via energy-efficiency technologies with presence of learning. We conclude from our analysis that, most of the existing energy efficiency technologies that are currently used in the U.S. iron and steel sector are cost effective. Penetration levels increases through the years, even though there is no price reduction. However, demonstration technologies are not economically feasible in the U.S. iron and steel sector with the current cost structure. In contrast, some of the demonstration technologies are adapted in the mid-term and their penetration levels increase as the prices go down with learning curve. We also observe large penetration of 225kg pulverized coal injection with the presence of learning.« less

Advances in Household Appliances- A Review

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bansal, Pradeep; Vineyard, Edward Allan; Abdelaziz, Omar

2011-01-01

An overview of options and potential barriers and risks for reducing the energy consumption, peak demand, and emissions for seven key energy consuming residential products (refrigerator-freezers, dishwashers, clothes washers, clothes dryers, electric ovens, gas ovens and microwave ovens) is presented. The paper primarily concentrates on the potential energy savings from the use of advanced technologies in appliances for the U.S. market. The significance and usefulness of each technology was evaluated in order to prioritize the R&D needs to improve energy efficiency of appliances in view of energy savings, cost, and complexity. The paper provides a snapshot of the future R&Dmore » needs for each of the technologies along with the associated barriers. Although significant energy savings may be achieved, one of the major barriers in most cases is high first cost. One way of addressing this issue and promoting the introduction of new technologies is to level the playing field for all manufacturers by establishing Minimum Energy Performance Standards (MEPS) which are not cost prohibitive and promoting energy efficient products through incentives to both manufacturers and consumers.« less

U. S. Department of Energy (DOE) Industrial Programs and Their Impacts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Weakley, Steven A.; Roop, Joseph M.

The U.S. Department of Energy’s Industrial Technologies Program (ITP) has been working with industry since 1976 to encourage the development and adoption of new, energy-efficient technologies. ITP has helped industry not only use energy and materials more efficiently but also improve environ¬mental performance, product quality, and productivity. To help ITP determine the impacts of its pro¬grams, Pacific Northwest National Laboratory (PNNL) periodically reviews and analyzes ITP pro¬gram benefits. PNNL contacts vendors and users of ITP-sponsored technologies that have been commer¬cialized, estimates the number of units that have penetrated the market, conducts engineering analyses to estimate energy savings from the newmore » technolo¬gies, and estimates air pollution and carbon emission reductions. This paper discusses the results of the most recent PNNL review (conducted in 2007). From 1976-2006, the commercialized technologies from ITP’s research and development (R&D) programs and other activities have cumulatively saved 5.65 quadrillion Btu, with a net cost savings of $37.8 billion.« less

U.S. Department of Energy (DOE) Industrial Programs and Their Impacts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Weakley, Steven A.; Roop, Joseph M.

The U.S. Department of Energy’s Industrial Technologies Program (ITP) has been working with industry since 1976 to encourage the development and adoption of new, energy-efficient technologies. ITP has helped industry not only use energy and materials more efficiently but also improve environ¬mental performance, product quality, and productivity. To help ITP determine the impacts of its pro¬grams, Pacific Northwest National Laboratory (PNNL) periodically reviews and analyzes ITP pro¬gram benefits. PNNL contacts vendors and users of ITP-sponsored technologies that have been commer¬cialized, estimates the number of units that have penetrated the market, conducts engineering analyses to estimate energy savings from the newmore » technolo¬gies, and estimates air pollution and carbon emission reductions. This paper discusses the results of the most recent PNNL review (conducted in 2006). From 1976-2005, the commercialized technologies from ITP’s research and development (R&D) programs and other activities have cumulatively saved 5.13 quadrillion Btu, with a net cost savings of $29.3 billion.« less

How Safe is Vehicle Safety? The Contribution of Vehicle Technologies to the Reduction in Road Casualties in France from 2000 to 2010

PubMed Central

Page, Yves; Hermitte, Thierry; Cuny, Sophie

2011-01-01

In France, over the last 10 years, road fatalities have decreased dramatically by 48%. This reduction is somewhat close to the target fixed by the European Commision in 2001 for the whole of Europe (−50 %). According to the French govnerment, 75% of this reduction was due to the implementation of automatic speed cameras on the roadsides from 2003 onwards. Yet, during this period, there was also a significantly increase in safety technology, new regulations in front and side impacts, and developments in Euro NCAP to improve passive safety in the vehicles. This paper set out to estimate the extent that vehicle safety technologies contributed to the road safety benefits over this decade. Using a combination of databases and fitment rates, the number of fatalities and hospitalized injuries saved in passenger car crashes was estimated for a number of safety technologies, individually and as a package including a 5 star EuroNCAP rating. The additional benefits from other public safety measures were also similarly estimated. The results showed that overall safety measures during this decade saved 240,676 fatalities + serious injuries, of which 173,663 were car occupants. Of these, 27,365 car occupants and 1,083 pedestrian savings could be attributed directly to vehicle safety improvements (11% overall). It was concluded that while public safety measures were responsible for the majority of the savings, enhanced vehicle safety technologies also made a significant improvement in the road toll in France during the last decade. As the take-up rate for these technologies improves, is expected to continue to provide even more benefits in the next 10-year period. PMID:22105388

The House that NASA Built

NASA Technical Reports Server (NTRS)

1977-01-01

Tech House, located at NASA's Langley Research Center, Hampton, Virginia, is a demonstration project in which aerospace and commercial building technology are combined to produce an energy-efficient home. Advanced technology offers savings to the family in utility costs and energy conservation. Solar panels on the roof of tech house provide the principal energy saving. They capture the sun's rays to heat water in pipes that run through the solar collectors. The heated water is then stored in a large, well insulated underground tank. A heat exchanger extracts beat from the water and blows it through ducts to warm the house. Tech House is well insulated for energy savings. The principal insulation is fireproof Tripolymer foam which is sprayed onto walls and ceilings in thicknesses up to six inches.

A homogeneous method to measure aminoacyl-tRNA synthetase aminoacylation activity using scintillation proximity assay technology.

PubMed

Macarrón, R; Mensah, L; Cid, C; Carranza, C; Benson, N; Pope, A J; Díez, E

2000-09-10

A new method to measure the aminoacylation of tRNA based upon the use of the scintillation proximity assay (SPA) technology has been developed. The assay detects incorporation of radiolabeled amino acids into cognate tRNA, catalyzed by a specific aminoacyl-tRNA synthetase (aaRS). Under acidic conditions, uncoated yttrium silicate SPA beads were found to bind tRNA aggregates, while the radiolabeled amino acid substrate remains in solution, resulting in good signal discrimination of these two species in the absence of any separation steps. The usefulness of this approach was demonstrated by measurement of steady-state kinetic constants and inhibitor binding constants for a range of aaRS enzymes in comparison with data from standard, trichloroacetic acid-precipitation-based assays. In all cases, the data were quantitatively comparable. Although the radioisotopic counting efficiency of the SPA method was less than that of standard liquid scintillation counting, the statistical performance (i.e., signal to background, variability, stability) of the SPA assays was at least equivalent to the separation-based methods. The assay was also shown to work well in miniaturized 384-well microtiter plate formats, resulting in considerable reagent savings. In summary, a new method to characterize aaRS activity is described that is faster and more amenable to high-throughput screening than traditional methods. Copyright 2000 Academic Press.

Cost Savings Realized by Implementation of Routine Microbiological Identification by Matrix-Assisted Laser Desorption Ionization–Time of Flight Mass Spectrometry

PubMed Central

Alby, Kevin; Kerr, Alan; Jones, Melissa; Gilligan, Peter H.

2015-01-01

Matrix-assisted laser desorption ionization–time of flight (MALDI-TOF) mass spectrometry (MS) is an emerging technology for rapid identification of bacterial and fungal isolates. In comparison to conventional methods, this technology is much less labor intensive and can provide accurate and reliable results in minutes from a single isolated colony. We compared the cost of performing the bioMérieux Vitek MALDI-TOF MS with conventional microbiological methods to determine the amount saved by the laboratory by converting to the new technology. Identification costs for 21,930 isolates collected between April 1, 2013, and March 31, 2014, were directly compared for MALDI-TOF MS and conventional methodologies. These isolates were composed of commonly isolated organisms, including commonly encountered aerobic and facultative bacteria and yeast but excluding anaerobes and filamentous fungi. Mycobacterium tuberculosis complex and rapidly growing mycobacteria were also evaluated for a 5-month period during the study. Reagent costs and a total cost analysis that included technologist time in addition to reagent expenses and maintenance service agreement costs were analyzed as part of this study. The use of MALDI-TOF MS equated to a net savings of $69,108.61, or 87.8%, in reagent costs annually compared to traditional methods. When total costs are calculated to include technologist time and maintenance costs, traditional identification would have cost $142,532.69, versus $68,886.51 with the MALDI-TOF MS method, resulting in a laboratory savings of $73,646.18, or 51.7%, annually by adopting the new technology. The initial cost of the instrument at our usage level would be offset in about 3 years. MALDI-TOF MS not only represents an innovative technology for the rapid and accurate identification of bacterial and fungal isolates, it also provides a significant cost savings for the laboratory. PMID:25994167

Cost Savings Realized by Implementation of Routine Microbiological Identification by Matrix-Assisted Laser Desorption Ionization-Time of Flight Mass Spectrometry.

PubMed

Tran, Anthony; Alby, Kevin; Kerr, Alan; Jones, Melissa; Gilligan, Peter H

2015-08-01

Matrix-assisted laser desorption ionization-time of flight (MALDI-TOF) mass spectrometry (MS) is an emerging technology for rapid identification of bacterial and fungal isolates. In comparison to conventional methods, this technology is much less labor intensive and can provide accurate and reliable results in minutes from a single isolated colony. We compared the cost of performing the bioMérieux Vitek MALDI-TOF MS with conventional microbiological methods to determine the amount saved by the laboratory by converting to the new technology. Identification costs for 21,930 isolates collected between April 1, 2013, and March 31, 2014, were directly compared for MALDI-TOF MS and conventional methodologies. These isolates were composed of commonly isolated organisms, including commonly encountered aerobic and facultative bacteria and yeast but excluding anaerobes and filamentous fungi. Mycobacterium tuberculosis complex and rapidly growing mycobacteria were also evaluated for a 5-month period during the study. Reagent costs and a total cost analysis that included technologist time in addition to reagent expenses and maintenance service agreement costs were analyzed as part of this study. The use of MALDI-TOF MS equated to a net savings of $69,108.61, or 87.8%, in reagent costs annually compared to traditional methods. When total costs are calculated to include technologist time and maintenance costs, traditional identification would have cost $142,532.69, versus $68,886.51 with the MALDI-TOF MS method, resulting in a laboratory savings of $73,646.18, or 51.7%, annually by adopting the new technology. The initial cost of the instrument at our usage level would be offset in about 3 years. MALDI-TOF MS not only represents an innovative technology for the rapid and accurate identification of bacterial and fungal isolates, it also provides a significant cost savings for the laboratory. Copyright © 2015, American Society for Microbiology. All Rights Reserved.

CFB repowering options

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gittinger, J.

1996-12-31

Circulating fluidized bed CFB repowering options are summarized. The following topics are discussed: why repower with CFB technology; advantages of repowering; two forms of of repowering; B and N`s internal recirculation CFB; space-saving design features; cost-saving design features; Ukrainian repowering project; and candidates for repowering.

Shining a Light on Savings.

ERIC Educational Resources Information Center

Kennedy, Mike

2000-01-01

Discusses how schools and universities can save energy and money by evaluating lighting systems and changing behaviors. Retrofitting older buildings with better lighting technology and use of natural light are examined. An example of an energy conservation education program to reduce energy waste is highlighted. (GR)

Vehicle Technology Simulation and Analysis Tools | Transportation Research

Science.gov Websites

| NREL Vehicle Technology Simulation and Analysis Tools Vehicle Technology Simulation and vehicle technologies with the potential to achieve significant fuel savings and emission reductions. NREL : Automotive Deployment Options Projection Tool The ADOPT modeling tool estimates vehicle technology

An overview of recovery of metals from slags.

PubMed

Shen, Huiting; Forssberg, E

2003-01-01

Various slags are produced as by-products in metallurgical processes or as residues in incineration processes. According to the origins and the characteristics, the main slags can be classified into three categories, namely ferrous slag, non-ferrous slag and incineration slag. This paper analysed and summarised the generation, characteristics and application of various slags, and discussed the potential effects of the slags on the environment. On this basis, a review of a number of methods for recovery of metals from the slags was made. It can be seen that a large amount of slags is produced each year. They usually contain a quantity of valuable metals except for blast furnace slag and they are actually a secondary resource of metals. By applying mineral processing technologies, such as crushing, grinding, magnetic separation, eddy current separation, flotation and so on, leaching or roasting, it is possible to recover metals such as Fe, Cr, Cu, Al, Pb, Zn, Co, Ni, Nb, Ta, Au, and Ag etc. from the slags. Recovery of metals from the slags and utilisation of the slags are important not only for saving metal resources, but also for protecting the environment.

12 CFR 550.250 - Must I keep fiduciary assets separate from other assets?

Code of Federal Regulations, 2010 CFR

2010-01-01

... 12 Banks and Banking 5 2010-01-01 2010-01-01 false Must I keep fiduciary assets separate from other assets? 550.250 Section 550.250 Banks and Banking OFFICE OF THRIFT SUPERVISION, DEPARTMENT OF THE TREASURY FIDUCIARY POWERS OF SAVINGS ASSOCIATIONS Exercising Fiduciary Powers Custody and Control of Assets...

12 CFR 550.430 - Must I keep fiduciary records separate and distinct from other records?

Code of Federal Regulations, 2010 CFR

2010-01-01

... 12 Banks and Banking 5 2010-01-01 2010-01-01 false Must I keep fiduciary records separate and distinct from other records? 550.430 Section 550.430 Banks and Banking OFFICE OF THRIFT SUPERVISION, DEPARTMENT OF THE TREASURY FIDUCIARY POWERS OF SAVINGS ASSOCIATIONS Exercising Fiduciary Powers Recordkeeping...

12 CFR 550.430 - Must I keep fiduciary records separate and distinct from other records?

Code of Federal Regulations, 2011 CFR

2011-01-01

... 12 Banks and Banking 5 2011-01-01 2011-01-01 false Must I keep fiduciary records separate and distinct from other records? 550.430 Section 550.430 Banks and Banking OFFICE OF THRIFT SUPERVISION, DEPARTMENT OF THE TREASURY FIDUCIARY POWERS OF SAVINGS ASSOCIATIONS Exercising Fiduciary Powers Recordkeeping...

12 CFR 550.250 - Must I keep fiduciary assets separate from other assets?

Code of Federal Regulations, 2011 CFR

2011-01-01

... 12 Banks and Banking 5 2011-01-01 2011-01-01 false Must I keep fiduciary assets separate from other assets? 550.250 Section 550.250 Banks and Banking OFFICE OF THRIFT SUPERVISION, DEPARTMENT OF THE TREASURY FIDUCIARY POWERS OF SAVINGS ASSOCIATIONS Exercising Fiduciary Powers Custody and Control of Assets...

Ceramic Technologies for Sustainability: Perspectives from Siemens Corporate Technology

NASA Astrophysics Data System (ADS)

Rossner, W.

2011-05-01

Climate change, environmental care, energy efficiency, scarcity of resources, population growth, demographic change, urbanization and globalization are the most pressing questions in the coming century. They will have an effect on all regions and groups of global society. Effective solutions will require immediate, efficient and concerted activities in all areas at the social, economic and environmental level. Since the 1980s it has been understood that developments should examine their sustainability more seriously to ensure that they do not compromise the ability of future generations to meet their own needs. This has also attributes to the sustainability demand of ceramic technologies. In the last decades a wide variety of ceramics developments have been brought to the markets, ranging from human implants to thermal barrier coatings in fossil power plants. There are innovative developments which should enter the market within the next years like solid oxide fuel cells or separation membranes for gas and liquids. Further ahead there will be ceramics with self-adapting, self-healing and multifunctional features to generate novel applications to save energy and to reduce carbon footprints across the entire value creation process of energy, industry, transportation and manufacturing.

In-situ resource utilization technologies for Mars life support systems.

PubMed

Sridhar, K R; Finn, J E; Kliss, M H

2000-01-01

The atmosphere of Mars has many of the ingredients that can be used to support human exploration missions. It can be "mined" and processed to produce oxygen, buffer gas, and water, resulting in significant savings on mission costs. The use of local materials, called ISRU (for in-situ resource utilization), is clearly an essential strategy for a long-term human presence on Mars from the standpoints of self-sufficiency, safety, and cost. Currently a substantial effort is underway by NASA to develop technologies and designs of chemical plants to make propellants from the Martian atmosphere. Consumables for life support, such as oxygen and water, will probably benefit greatly from this ISRU technology development for propellant production. However, the buffer gas needed to dilute oxygen for breathing is not a product of a propellant production plant. The buffer gas needs on each human Mars mission will probably be in the order of metric tons, primarily due to losses during airlock activity. Buffer gas can be separated, compressed, and purified from the Mars atmosphere. This paper discusses the buffer gas needs for a human mission to Mars and consider architectures for the generation of buffer gas including an option that integrates it to the propellant production plant.

Future Propulsion Opportunities for Commuter Airplanes

NASA Technical Reports Server (NTRS)

Strack, W. C.

1982-01-01

Commuter airplane propulsion opportunities are summarized. Consideration is given to advanced technology conventional turboprop engines, advanced propellers, and several unconventional alternatives: regenerative turboprops, rotaries, and diesels. Advanced versions of conventional turboprops (including propellers) offer 15-20 percent savings in fuel and 10-15 percent in DOC compared to the new crop of 1500-2000 SHP engines currently in development. Unconventional engines could boost the fuel savings to 30-40 percent. The conclusion is that several important opportunities exist and, therefore, powerplant technology need not plateau.

Caring and professional practice settings: the impact of technology, change, and efficiency.

PubMed

Crow, G

2001-01-01

Technology, change, efficiency, and caring are not necessarily concepts that are used in the same sentence when describing motivational and professional practice settings. Caring within health care organizations can take many forms. One of the most significant and meaningful forms is through building networks for shared decision making and shared accountability. While caring can save the life of a patient and convey trust and commitment to patients, families, and staff, it can also save the life of your organization.

Concept for a power system controller for large space electrical power systems

NASA Technical Reports Server (NTRS)

Lollar, L. F.; Lanier, J. R., Jr.; Graves, J. R.

1981-01-01

The development of technology for a fail-operatonal power system controller (PSC) utilizing microprocessor technology for managing the distribution and power processor subsystems of a large multi-kW space electrical power system is discussed. The specific functions which must be performed by the PSC, the best microprocessor available to do the job, and the feasibility, cost savings, and applications of a PSC were determined. A limited function breadboard version of a PSC was developed to demonstrate the concept and potential cost savings.

Utilization of Porous Media for Condensing Heat Exchangers

NASA Technical Reports Server (NTRS)

Tuan, George C.

2006-01-01

The use of porous media as a mean of separating liquid condensate from the air stream in condensing heat exchangers has been explored in the past inside small plant growth chambers and in the Apollo Command Module. Both applications used a cooled porous media made of sintered stainless steel to cool and separate condensation from the air stream. However, the main issues with the utilization of porous media in the past have been the deterioration of the porous media over long duration, such as clogging and changes in surface wetting characteristics. In addition, for long duration usage, biofilm growth from microorganisms on the porous medial would also be an issue. In developing Porous Media Condensing Heat Exchangers (PMCHX) for future space applications, different porous materials and microbial growth control methods will need to be explored. This paper explores the work performed at JSC and GRC to evaluate different porous materials and microbial control methods to support the development of a Porous Media Condensing Heat Exchanger. It outlines the basic principles for designing a PMCHX and issues that were encountered and ways to resolve those issues. The PMCHX has potential of mass, volume, and power savings over current CHX and water separator technology and would be beneficial for long duration space missions.

RAPID DETERMINATION OF ACTINIDES IN URINE BY INDUCTIVELY-COUPLED PLASMA MASS SPECTROMETRY AND ALPHA SPECTROMETRY: A HYBRID APPROACH

DOE Office of Scientific and Technical Information (OSTI.GOV)

Maxwell, S.; Jones, V.

2009-05-27

A new rapid separation method that allows separation and preconcentration of actinides in urine samples was developed for the measurement of longer lived actinides by inductively coupled plasma mass spectrometry (ICP-MS) and short-lived actinides by alpha spectrometry; a hybrid approach. This method uses stacked extraction chromatography cartridges and vacuum box technology to facilitate rapid separations. Preconcentration, if required, is performed using a streamlined calcium phosphate precipitation. Similar technology has been applied to separate actinides prior to measurement by alpha spectrometry, but this new method has been developed with elution reagents now compatible with ICP-MS as well. Purified solutions are splitmore » between ICP-MS and alpha spectrometry so that long- and short-lived actinide isotopes can be measured successfully. The method allows for simultaneous extraction of 24 samples (including QC samples) in less than 3 h. Simultaneous sample preparation can offer significant time savings over sequential sample preparation. For example, sequential sample preparation of 24 samples taking just 15 min each requires 6 h to complete. The simplicity and speed of this new method makes it attractive for radiological emergency response. If preconcentration is applied, the method is applicable to larger sample aliquots for occupational exposures as well. The chemical recoveries are typically greater than 90%, in contrast to other reported methods using flow injection separation techniques for urine samples where plutonium yields were 70-80%. This method allows measurement of both long-lived and short-lived actinide isotopes. 239Pu, 242Pu, 237Np, 243Am, 234U, 235U and 238U were measured by ICP-MS, while 236Pu, 238Pu, 239Pu, 241Am, 243Am and 244Cm were measured by alpha spectrometry. The method can also be adapted so that the separation of uranium isotopes for assay is not required, if uranium assay by direct dilution of the urine sample is preferred instead. Multiple vacuum box locations may be set-up to supply several ICP-MS units with purified sample fractions such that a high sample throughput may be achieved, while still allowing for rapid measurement of short-lived actinides by alpha spectrometry.« less

NREL Technical Reports Guide the Way to 50% Energy Savings in Hospitals, Office Buildings (Fact Sheet)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

2011-02-01

Researchers at the National Renewable Energy Laboratory (NREL) have developed two technical reports that provide recommendations to help designers and operators of large office buildings and hospitals achieve at least a 50% energy savings using existing technology.

Energy Saving Melting and Revert Reduction Technology (E-SMARRT): Mechanical Performance of Dies

DOE Office of Scientific and Technical Information (OSTI.GOV)

R. Allen Miller, Principal Investigator; Kabiri-Bamoradian, Contributors: Khalil; Delgado-Garza, Abelardo

2011-09-13

As a net shape process, die casting is intrinsically efficient and improvements in energy efficiency are strongly dependent on design and process improvements that reduce scrap rates so that more of the total consumed energy goes into acceptable, usable castings. A casting that is distorted and fails to meet specified dimensional requirements is typically remelted but this still results in a decrease in process yield, lost productivity, and increased energy consumption. This work focuses on developing, and expanding the use of, computer modeling methods that can be used to improve the dimensional accuracy of die castings and produce die designsmore » and machine/die setups that reduce rejection rates due to dimensional issues. A major factor contributing to the dimensional inaccuracy of the casting is the elastic deformations of the die cavity caused by the thermo mechanical loads the dies are subjected to during normal operation. Although thermal and die cavity filling simulation are widely used in the industry, structural modeling of the die, particularly for managing part distortion, is not yet widely practiced. This may be due in part to the need to have a thorough understanding of the physical phenomenon involved in die distortion and the mathematical theory employed in the numerical models to efficiently model the die distortion phenomenon. Therefore, two of the goals of this work are to assist in efforts to expand the use of structural modeling and related technologies in the die casting industry by 1) providing a detailed modeling guideline and tutorial for those interested in developing the necessary skills and capability and 2) by developing simple meta-models that capture the results and experience gained from several years of die distortion research and can be used to predict key distortion phenomena of relevance to a die caster with a minimum of background and without the need for simulations. These objectives were met. A detailed modeling tutorial was provided to NADCA for distribution to the industry. Power law based meta-models for predicting machine tie bar loading and for predicting maximum parting surface separation were successfully developed and tested against simulation results for a wide range of machines and experimental data. The models proved to be remarkably accurate, certainly well within the requirements for practical application. In addition to making die structural modeling more accessible, the work advanced the state-of-the-art by developing improved modeling of cavity pressure effects, which is typically modeled as a hydrostatic boundary condition, and performing a systematic analysis of the influence of ejector die design variables on die deflection and parting plane separation. This cavity pressure modeling objective met with less than complete success due to the limits of current finite element based fluid structure interaction analysis methods, but an improved representation of the casting/die interface was accomplished using a combination of solid and shell elements in the finite element model. This approximation enabled good prediction of final part distortion verified with a comprehensive evaluation of the dimensions of test castings produced with a design experiment. An extra deliverable of the experimental work was development of high temperature mechanical properties for the A380 die casting alloy. The ejector side design objective was met and the results were incorporated into the metamodels described above. This new technology was predicted to result in an average energy savings of 2.03 trillion BTU's/year over a 10 year period. Current (2011) annual energy saving estimates over a ten year period, based on commercial introduction in 2009, a market penetration of 70% by 2014 is 4.26 trillion BTU's/year by 2019. Along with these energy savings, reduction of scrap and improvement in casting yield will result in a reduction of the environmental emissions associated with the melting and pouring of the metal which will be saved as a result of this technology. The average annual estimate of CO2 reduction per year through 2020 is 0.085 Million Metric Tons of Carbon Equivalent (MM TCE).« less

New Manufacturing Method for Paper Filler and Fiber Material

DOE Office of Scientific and Technical Information (OSTI.GOV)

Doelle, Klaus

2013-08-25

The use of fillers in printing and writing papers has become a prerequisite for competing in a global market to reduce the cost of materials. Use of calcium carbonates (ranging from 18% to 30%) as filler is a common practice in the paper industry but the choices of fillers for each type of papers vary widely according to its use. The market for uncoated digital printing paper is one that continues to introduce exciting growth projections. and it is important to understand the effect that new manufacturing methods of calcium carbonates have on the energy efficiency and paper production. Research conducted under this award showed that the new fiber filler composite material has the potential to increase the paper filler content by up to 5% without losing mechanical properties. Benefits of the technology can be summarized as follows for a 1% filler increase per metric ton of paper produced: (i) production cost savings overmore » $$12, (ii) Energy savings of 100,900 btu, (iii) CO{sub 2} emission savings of 33 lbs, and additional savings for wood preparation, pulping, recovery of 203593 btu with a 46lbs of CO{sub 2} emission savings per 1% filler increase. In addition the technology has the potential to save: (i) additional $$3 per ton of bleached pulp produced, (ii) bleaching energy savings of 170,000 btu, (iii) bleaching CO{sub 2} emission savings of 39 lbs, and (iv) additional savings for replacing conventional bleaching chemicals with a sustainable bleaching chemical is estimated to be 900,000 btu with a 205 lbs of CO{sub 2} emission savings per ton of bleached pulp produced. All the above translates to a estimated annual savings for a 12% filler increase of 296 trillion buts or 51 million barrel of oil equivalent (BOE) or 13.7% of the industries energy demand. This can lead to a increase of renewable energy usage from 56% to close to 70% for the industry sector. CO{sub 2} emission of the industry at a 12% filler increase could be lowered by over 39 million tons annually. If the new technology could be implemented for bleaching process a total annual estimated energy savings potential of 64 trillion buts or 11 million barrel of oil equivalent (BOE) equal to 3% of the paper industries energy demand could be realized. This could lead to a increase of renewable energy usage from 56% to close to 60% for the industry. CO{sub 2} emissions could be lowered by over 7.4 million tons annually. It is estimated that an installed system could also yield a 75 to 100% return of investment (ROI) rate for the capital equipment that need to be installed for the fiber filler composite manufacturing process.« less

Building Better Cost-Effective Schools.

ERIC Educational Resources Information Center

Cunningham, Cody; Chase, Greg

2003-01-01

Discusses how schools can effectively plan ahead for the rapid advancement of technology through use of wireless technology. Describes its flexibility and savings, and planning and design issues. (EV)

21st century locomotive technology: quarterly technical status report 26

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lembit Salasoo; Ramu Chandra

2009-08-24

Parasitic losses due to hybrid sodium battery thermal management do not significantly reduce the fuel saving benefits of the hybrid locomotive. Optimal thermal management trajectories were converted into realizable algorithms which were robust and gave excellent performance to limit thermal excusions and maintain fuel savings.

Cost benefit for assessment of intermediate coronary stenosis with fractional flow reserve in public and private sectors in australia.

PubMed

Murphy, J C; Hansen, P S; Bhindi, R; Figtree, G A; Nelson, G I C; Ward, M R

2014-09-01

Fractional Flow Reserve (FFR) is a proven technology for guiding percutaneous coronary intervention (PCI), but is not reimbursed despite the fact that it is frequently used to defer PCI. Costs incurred with use of FFR were compared in both the public and private sectors with the costs that would have been incurred if the technology was not available using consecutive cases over a two year period in a public teaching hospital and its co-located private hospital. FFR was performed on 143 lesions in 120 patients. FFR was < 0.80 in 37 lesions in 34 patients and 25 underwent PCI while 11 had CABG. It was estimated that without FFR 78 lesions in 70 patients would have had PCI with 17 patients having CABG with 35 additional functional tests. Despite a cost of $A1200 per wire, FFR actually saved money. Mean savings in the public sector were $1200 per patient while in the private sector the savings were $5000 per patient. FFR use saves money for the Federal Government in the public sector and for the Private Health Funds in the private sector. These financial benefits are seen in addition to the improved outcomes seen with this technology. Copyright © 2014. Published by Elsevier B.V.

A novel application of concentrated solar thermal energy in foundries.

PubMed

Selvaraj, J; Harikesavan, V; Eshwanth, A

2016-05-01

Scrap preheating in foundries is a technology that saves melting energy, leading to economic and environmental benefits. The proposed method in this paper utilizes solar thermal energy for preheating scrap, effected through a parabolic trough concentrator that focuses sunlight onto a receiver which carries the metallic scrap. Scraps of various thicknesses were placed on the receiver to study the heat absorption by them. Experimental results revealed the pattern with which heat is gained by the scrap, the efficiency of the process and how it is affected as the scrap gains heat. The inferences from them gave practical guidelines on handling scraps for best possible energy savings. Based on the experiments conducted, preheat of up to 160 °C and a maximum efficiency of 70 % and a minimum efficiency of 40 % could be achieved across the time elapsed and heat gained by the scrap. Calculations show that this technology has the potential to save around 8 % of the energy consumption in foundries. Cumulative benefits are very encouraging: 180.45 million kWh of energy savings and 203,905 t of carbon emissions cut per year across the globe. This research reveals immense scope for this technology to be adopted by foundries throughout the world.

Insurance choice and tax-preferred health savings accounts.

PubMed

Cardon, James H; Showalter, Mark H

2007-03-01

We develop an infinite horizon utility maximization model of the interaction between insurance choice and tax-preferred health savings accounts. The model can be used to examine a wide range of policy options, including flexible spending accounts, health savings accounts, and health reimbursement accounts. We also develop a 2-period model to simulate various implications of the model. Key results from the simulation analysis include the following: (1) with no adverse selection, use of unrestricted health savings accounts leads to modest welfare gains, after accounting for the tax revenue loss; (2) with adverse selection and an initial pooling equilibrium comprised of "sick" and "healthy" consumers, introducing HSAs can, but does not necessarily, lead to a new pooling equilibrium. The new equilibrium results in a higher coinsurance rate, an increase in expected utility for healthy consumers, and a decrease in expected utility for sick consumers; (3) with adverse selection and a separating equilibrium, both sick and healthy consumers are better off with a health savings account; (4) efficiency gains are possible when insurance contracts are explicitly linked to tax-preferred health savings accounts.

Save water to save carbon and money: developing abatement costs for expanded greenhouse gas reduction portfolios.

PubMed

Stokes, Jennifer R; Hendrickson, Thomas P; Horvath, Arpad

2014-12-02

The water-energy nexus is of growing interest for researchers and policy makers because the two critical resources are interdependent. Their provision and consumption contribute to climate change through the release of greenhouse gases (GHGs). This research considers the potential for conserving both energy and water resources by measuring the life-cycle economic efficiency of greenhouse gas reductions through the water loss control technologies of pressure management and leak management. These costs are compared to other GHG abatement technologies: lighting, building insulation, electricity generation, and passenger transportation. Each cost is calculated using a bottom-up approach where regional and temporal variations for three different California water utilities are applied to all alternatives. The costs and abatement potential for each technology are displayed on an environmental abatement cost curve. The results reveal that water loss control can reduce GHGs at lower cost than other technologies and well below California's expected carbon trading price floor. One utility with an energy-intensive water supply could abate 135,000 Mg of GHGs between 2014 and 2035 and save--rather than spend--more than $130/Mg using the water loss control strategies evaluated. Water loss control technologies therefore should be considered in GHG abatement portfolios for utilities and policy makers.

Cogeneration Technology Alternatives Study (CTAS). Volume 3: Energy conversion system characteristics

NASA Technical Reports Server (NTRS)

1980-01-01

Six current and thirty-six advanced energy conversion systems were defined and combined with appropriate balance of plant equipment. Twenty-six industrial processes were selected from among the high energy consuming industries to serve as a frame work for the study. Each conversion system was analyzed as a cogenerator with each industrial plant. Fuel consumption, costs, and environmental intrusion were evaluated and compared to corresponding traditional values. The advanced energy conversion technologies indicated reduced fuel consumption, costs, and emissions. Fuel energy savings of 10 to 25 percent were predicted compared to traditional on site furnaces and utility electricity. With the variety of industrial requirements, each advanced technology had attractive applications. Fuel cells indicated the greatest fuel energy savings and emission reductions. Gas turbines and combined cycles indicated high overall annual savings. Steam turbines and gas turbines produced high estimated returns. In some applications, diesels were most efficient. The advanced technologies used coal derived fuels, or coal with advanced fluid bed combustion or on site gasifications. Data and information for both current and advanced energy conversion technology are presented. Schematic and physical descriptions, performance data, equipment cost estimates, and predicted emissions are included. Technical developments which are needed to achieve commercialization in the 1985-2000 period are identified.

40 CFR 80.1163 - What penalties apply under the RFS program?

Code of Federal Regulations, 2010 CFR

2010-07-01

..., for every day of each such violation and the amount of economic benefit or savings resulting from each... obligation, during any averaging period, is subject to a separate day of violation for each day in the..., a requirement of any provision of this subpart is liable for a separate day of violation for each...

Rock Port Celebrates New Technology Center.

ERIC Educational Resources Information Center

Grones, Freda

1997-01-01

Discusses the advantages dome architecture gave to a new school technology center in Rock Port, Missouri. Advantages cover energy cost savings, lighting, storage space, aesthetics, accessibility, and convenience. (GR)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Crolley, R.; Thompson, M.

There has been a need for a faster and cheaper deployment model for information technology (IT) solutions to address waste management needs at US Department of Energy (DOE) complex sites for years. Budget constraints, challenges in deploying new technologies, frequent travel, and increased job demands for existing employees have prevented IT organizations from staying abreast of new technologies or deploying them quickly. Despite such challenges, IT organizations have added significant value to waste management handling through better worker safety, tracking, characterization, and disposition at DOE complex sites. Systems developed for site-specific missions have broad applicability to waste management challenges andmore » in many cases have been expanded to meet other waste missions. Radio frequency identification (RFID) and global positioning satellite (GPS)-enabled solutions have reduced the risk of radiation exposure and safety risks. New web-based and mobile applications have enabled precision characterization and control of nuclear materials. These solutions have also improved operational efficiencies and shortened schedules, reduced cost, and improved regulatory compliance. Collaboration between US Department of Energy (DOE) complex sites is improving time to delivery and cost efficiencies for waste management missions with new information technologies (IT) such as wireless computing, global positioning satellite (GPS), and radio frequency identification (RFID). Integrated solutions developed at separate DOE complex sites by new technology Centers of Excellence (CoE) have increased material control and accountability, worker safety, and environmental sustainability. CoEs offer other DOE sister sites significant cost and time savings by leveraging their technology expertise in project scoping, implementation, and ongoing operations.« less

Ethical considerations for the utilization of tele-health technologies in home and hospice care by the nursing profession.

PubMed

Demiris, George; Oliver, Debra Parker; Courtney, Karen L

2006-01-01

Home care, including hospice care, is a growing component of the current healthcare system and pertains to care services that are provided to individuals, their family members, and caregivers in their own residence. Both domains face funding limitations as life expectancy and the segment of the population older than 65 years increase. Tele-health, defined as the use of advanced telecommunication technologies to enable communication between patients and healthcare providers separated by geographic distance, is perceived as a concept that can enhance both home and hospice care and address some of the current challenges. This article discusses ethical challenges associated with the utilization of tele-health technologies by the nursing profession in the home setting. These factors form a framework for the ethical considerations that result from the introduction of these technologies in nursing practice. Specifically, the article discusses the issue of privacy and confidentiality of patient data, informed consent, equity of access, promoting dependency versus independence, the lack of human touch and the impact of technology on the nurse-patient relationship, and the medicalization of the home environment. These issues constitute a road map both for nursing practitioners who are aiming to provide an efficient delivery of services in the home and for nursing administrators who are asked to make judgments about the use of tele-health technology as a supplement to traditional care and as a cost-saving tool.

Improved System Yields $100,000 Annual Savings (Systems Analysis at Alcoa Yields Significant Savings)

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

1999-01-01

In another Office of Industrial Technologies Motor Challenge Success Story, Alcoa (formerly Alumax) aluminum reduced annual energy consumption by 12% and reduced both maintenance and noise levels. Order this fact sheet now to learn how your company can both increase energy efficiency and decrease pollution.

OpenADR Specification to Ease Saving Power in Buildings

ScienceCinema

None

2017-12-09

A new data model developed by researchers at the Department of Energys Lawrence Berkeley National Laboratory and their colleagues at other universities and in the private sector will help facilities and buildings save power through automated demand response technology, and advance the development of the Smart Grid.

Electric portfolio modeling with stochastic water - climate interactions: Implications for co-management of water and electric utilities

NASA Astrophysics Data System (ADS)

Woldeyesus, Tibebe Argaw

Water supply constraints can significantly restrict electric power generation, and such constraints are expected to worsen with future climate change. The overarching goal of this thesis is to incorporate stochastic water-climate interactions into electricity portfolio models and evaluate various pathways for water savings in co-managed water-electric utilities. Colorado Springs Utilities (CSU) is used as a case study to explore the above issues. The thesis consists of three objectives: Characterize seasonality of water withdrawal intensity factors (WWIF) for electric power generation and develop a risk assessment framework due to water shortages; Incorporate water constraints into electricity portfolio models and evaluate the impact of varying capital investments (both power generation and cooling technologies) on water use and greenhouse gas emissions; Compare the unit cost and overall water savings from both water and electric sectors in co-managed utilities to facilitate overall water management. This thesis provided the first discovery and characterization of seasonality of WWIF with distinct summertime and wintertime variations of +/-17% compared to the power plant average (0.64gal/kwh) which itself is found to be significantly higher than the literature average (0.53gal/kwh). Both the streamflow and WWIF are found to be highly correlated with monthly average temperature (r-sq = 89%) and monthly precipitation (r-sq of 38%) enabling stochastic simulation of future WWIF under moderate climate change scenario. Future risk to electric power generation also showed the risk to be underestimated significantly when using either the literature average or the power plant average WWIF. Seasonal variation in WWIF along with seasonality in streamflow, electricity demand and other municipal water demands along with storage are shown to be important factors for more realistic risk estimation. The unlimited investment in power generation and/or cooling technologies is also found to save water and GHG emissions by 68% and 75% respectively at a marginal levelized cost increase of 12%. In contrast, the zero investment scenarios (which optimizes exiting technologies to address water scarcity constraints on power generation) shows 50% water savings and 23% GHG emissions reduction at a relatively high marginal levelized cost increase of 37%. Water saving strategies in electric sector show very high cost of water savings (48,000 and 200,000)/Mgal-year under unlimited investment and zero investment scenarios respectively, but they have greater water saving impacts of 6% to CSU municipal water demand; while the individual water saving strategies from water sector have low cost of water savings ranging from (37-1,500)/Mgal-year but with less than 0.5% water reduction impact to CSU due to their low penetration. On the other hand, use of reclaimed water for power plant cooling systems have shown great water savings of up to 92% against the BAU and cost of water saving from (0-73,000)/Mgal-year when integrated with unlimited investment and zero investment water minimizing scenarios respectively in the electric sector. Overall, cities need to focus primarily on use of reclaimed water and in new generation technologies' investment including cooling system retrofits while focusing on expanding the penetration rate of individual water saving strategies in the water sector.

Potential benefits for propfan technology on derivatives of future short- to medium-range transport aircraft

NASA Technical Reports Server (NTRS)

Goldsmith, I. M.; Bowles, J. V.

1980-01-01

It is noted that several NASA-sponsored studies have identified a substantial potential fuel savings for high subsonic speed aircraft utilizing the propfan concept compared to the equivalent technology turbofan aircraft. Attention is given to a feasibility study for propfan-powered short- to medium-haul commercial transport aircraft conducted to evaluate potential fuel savings and identify critical technology requirements using the latest propfan performance data. An analysis is made of the design and performance characteristics of a wing-mounted and two-aft-mounted derivative propfan aircraft configurations, based on a DC-9 Super 80 airframe, which are compared to the baseline turbofan design. Finally, recommendations for further research efforts are also made.

Optical design of a light-emitting diode lamp for a maritime lighthouse.

PubMed

Jafrancesco, D; Mercatelli, L; Sansoni, P; Fontani, D; Sani, E; Coraggia, S; Meucci, M; Francini, F

2015-04-10

Traffic signaling is an emerging field for light-emitting diode (LED) applications. This sustainable power-saving illumination technology can be used in maritime signaling thanks to the recently updated norms, where the possibility to utilize LED sources is explicitly cited, and to the availability of high-power white LEDs that, combined with suitable lenses, permit us to obtain well-collimated beams. This paper describes the optical design of a LED-based lamp that can replace a traditional lamp in an authentic marine lighthouse. This source recombines multiple separated LEDs realizing a quasi-punctual localized source. Advantages can be lower energy consumption, higher efficiency, longer life, fewer faults, slower aging, and minor maintenance costs. The proposed LED source allows us to keep and to utilize the old Fresnel lenses of the lighthouse, which very often have historical value.

Defense Health Care Reform: Additional Implementation Details Would Increase Transparency of DOD’s Plans and Enhance Accountability

DTIC Science & Technology

2013-11-01

on timelines; and was not required to include information on shared services because the reporting time frame was not applicable. GAO also assessed...implementation costs and aggregated cost-savings estimates for the consolidation of four shared services . However, some key details of a sound business...case were missing, such as the basis for the savings. DOD’s business cases aggregated the separate business lines of its shared services , which

Evaluation for Water Conservation in Agriculture: Using a Multi-Method Econometric Approach

NASA Astrophysics Data System (ADS)

Ramirez, A.; Eaton, D. J.

2012-12-01

Since the 1960's, farmers have implemented new irrigation technology to increase crop production and planting acreage. At that time, technology responded to the increasing demand for food due to world population growth. Currently, the problem of decreased water supply threatens to limit agricultural production. Uncertain precipitation patterns, from prolonged droughts to irregular rains, will continue to hamper planting operations, and farmers are further limited by an increased competition for water from rapidly growing urban areas. Irrigation technology promises to reduce water usage while maintaining or increasing farm yields. The challenge for water managers and policy makers is to quantify and redistribute these efficiency gains as a source of 'new water.' Using conservation in farming as a source of 'new water' requires accurately quantifying the efficiency gains of irrigation technology under farmers' actual operations and practices. From a water resource management and policy perspective, the efficiency gains from conservation in farming can be redistributed to municipal, industrial and recreational uses. This paper presents a methodology that water resource managers can use to statistically verify the water savings attributable to conservation technology. The specific conservation technology examined in this study is precision leveling, and the study includes a mixed-methods approach using four different econometric models: Ordinary Least Squares, Fixed Effects, Propensity Score Matching, and Hierarchical Linear Models. These methods are used for ex-post program evaluation where random assignment is not possible, and they could be employed to evaluate agricultural conservation programs, where participation is often self-selected. The principal method taken in this approach is Hierarchical Linear Models (HLM), a useful model for agriculture because it incorporates the hierarchical nature of the data (fields, tenants, and landowners) as well as crop rotation (fields in and out of production). The other three methods provide verification of the accuracy of the HLM model and create a robust comparison of the water savings estimates. Seventeen factors were used to isolate the effect of precision leveling from variations in climate, investments in other irrigation improvements, and farmers' management skills. These statistical analyses yield accurate water savings estimates because they consider farmers' actual irrigation technology and practices. Results suggest that savings from water conservation technology under farmers' actual production systems and management are less than those reported by experimental field studies. These water savings measure the 'in situ' effect of the technology, considering farmers' actual irrigation practices and technology. In terms of the accuracy of the models, HLM provides the most precise estimate of the impact of precision leveling on a field's water usage. The HLM estimate was within the 95% confidence interval of the other three models, thus verifying the accuracy and robustness of the statistical findings and model.

A framework for quantifying the impact of occupant behavior on energy savings of energy conservation measures

DOE PAGES

Sun, K; Hong, T

2017-07-01

© 2017 Elsevier B.V. To improve energy efficiency—during new buildings design or during a building retrofit—evaluating the energy savings potential of energy conservation measures (ECMs) is a critical task. In building retrofits, occupant behavior significantly impacts building energy use and is a leading factor in uncertainty when determining the effectiveness of retrofit ECMs. Current simulation-based assessment methods simplify the representation of occupant behavior by using a standard or representative set of static and homogeneous assumptions ignoring the dynamics, stochastics, and diversity of occupant's energy-related behavior in buildings. The simplification contributes to significant gaps between the simulated and measured actual energymore » performance of buildings. This study presents a framework for quantifying the impact of occupant behaviors on ECM energy savings using building performance simulation. During the first step of the study, three occupant behavior styles (austerity, normal, and wasteful) were defined to represent different levels of energy consciousness of occupants regarding their interactions with building energy systems (HVAC, windows, lights and plug-in equipment). Next, a simulation workflow was introduced to determine a range of the ECM energy savings. Then, guidance was provided to interpret the range of ECM savings to support ECM decision making. Finally, a pilot study was performed in a real building to demonstrate the application of the framework. Simulation results show that the impact of occupant behaviors on ECM savings vary with the type of ECM. Occupant behavior minimally affects energy savings for ECMs that are technology-driven (the relative savings differ by less than 2%) and have little interaction with the occupants; for ECMs with strong occupant interaction, such as the use of zonal control variable refrigerant flow system and natural ventilation, energy savings are significantly affected by occupant behavior (the relative savings differ by up to 20%). The study framework provides a novel, holistic approach to assessing the uncertainty of ECM energy savings related to occupant behavior, enabling stakeholders to understand and assess the risk of adopting energy efficiency technologies for new and existing buildings.« less

A framework for quantifying the impact of occupant behavior on energy savings of energy conservation measures

DOE PAGES

Sun, Kaiyu; Hong, Tianzhen

2017-04-27

To improve energy efficiency—during new buildings design or during a building retrofit—evaluating the energy savings potential of energy conservation measures (ECMs) is a critical task. In building retrofits, occupant behavior significantly impacts building energy use and is a leading factor in uncertainty when determining the effectiveness of retrofit ECMs. Current simulation-based assessment methods simplify the representation of occupant behavior by using a standard or representative set of static and homogeneous assumptions ignoring the dynamics, stochastics, and diversity of occupant's energy-related behavior in buildings. The simplification contributes to significant gaps between the simulated and measured actual energy performance of buildings. Thismore » paper presents a framework for quantifying the impact of occupant behaviors on ECM energy savings using building performance simulation. During the first step of the study, three occupant behavior styles (austerity, normal, and wasteful) were defined to represent different levels of energy consciousness of occupants regarding their interactions with building energy systems (HVAC, windows, lights and plug-in equipment). Next, a simulation workflow was introduced to determine a range of the ECM energy savings. Then, guidance was provided to interpret the range of ECM savings to support ECM decision making. Finally, a pilot study was performed in a real building to demonstrate the application of the framework. Simulation results show that the impact of occupant behaviors on ECM savings vary with the type of ECM. Occupant behavior minimally affects energy savings for ECMs that are technology-driven (the relative savings differ by less than 2%) and have little interaction with the occupants; for ECMs with strong occupant interaction, such as the use of zonal control variable refrigerant flow system and natural ventilation, energy savings are significantly affected by occupant behavior (the relative savings differ by up to 20%). Finally, the study framework provides a novel, holistic approach to assessing the uncertainty of ECM energy savings related to occupant behavior, enabling stakeholders to understand and assess the risk of adopting energy efficiency technologies for new and existing buildings.« less

A framework for quantifying the impact of occupant behavior on energy savings of energy conservation measures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sun, Kaiyu; Hong, Tianzhen

To improve energy efficiency—during new buildings design or during a building retrofit—evaluating the energy savings potential of energy conservation measures (ECMs) is a critical task. In building retrofits, occupant behavior significantly impacts building energy use and is a leading factor in uncertainty when determining the effectiveness of retrofit ECMs. Current simulation-based assessment methods simplify the representation of occupant behavior by using a standard or representative set of static and homogeneous assumptions ignoring the dynamics, stochastics, and diversity of occupant's energy-related behavior in buildings. The simplification contributes to significant gaps between the simulated and measured actual energy performance of buildings. Thismore » paper presents a framework for quantifying the impact of occupant behaviors on ECM energy savings using building performance simulation. During the first step of the study, three occupant behavior styles (austerity, normal, and wasteful) were defined to represent different levels of energy consciousness of occupants regarding their interactions with building energy systems (HVAC, windows, lights and plug-in equipment). Next, a simulation workflow was introduced to determine a range of the ECM energy savings. Then, guidance was provided to interpret the range of ECM savings to support ECM decision making. Finally, a pilot study was performed in a real building to demonstrate the application of the framework. Simulation results show that the impact of occupant behaviors on ECM savings vary with the type of ECM. Occupant behavior minimally affects energy savings for ECMs that are technology-driven (the relative savings differ by less than 2%) and have little interaction with the occupants; for ECMs with strong occupant interaction, such as the use of zonal control variable refrigerant flow system and natural ventilation, energy savings are significantly affected by occupant behavior (the relative savings differ by up to 20%). Finally, the study framework provides a novel, holistic approach to assessing the uncertainty of ECM energy savings related to occupant behavior, enabling stakeholders to understand and assess the risk of adopting energy efficiency technologies for new and existing buildings.« less

Disaster Relief and Emergency Medical Services Project (DREAMS TM): Digital EMS

DTIC Science & Technology

2000-10-01

exchanges between the hospital and the EMS vehicle. By creating the virtual presence of a physician at or near the emergency scene, more lives will be saved ...address, cross street, zip code etc. The map can be saved to the clipboard or to an EMF graphics file for use by other applications in the system. 29...section can be found in Appendix B. The EMS personnel on board the ambulance can benefit greatly from technology integration. Several time- saving

Alternative Fuels Data Center

Science.gov Websites

technologies and operational practices which increase fuel efficiency and reduce emissions from goods movement . EPA provides partners with performance benchmarking tools, fleet management best practices, technology is working with partners to test and verify advanced technologies and operational practices that save

Composite Technology for Exploration

NASA Technical Reports Server (NTRS)

Fikes, John

2017-01-01

The CTE (Composite Technology for Exploration) Project will develop and demonstrate critical composites technologies with a focus on joints that utilize NASA expertise and capabilities. The project will advance composite technologies providing lightweight structures to support future NASA exploration missions. The CTE project will demonstrate weight-saving, performance-enhancing bonded joint technology for Space Launch System (SLS)-scale composite hardware.

The potential environmental gains from recycling waste plastics: Simulation of transferring recycling and recovery technologies to Shenyang, China

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen Xudong, E-mail: chen.xudong@nies.go.jp; National Institute for Environmental Studies, 16-2 Onogawa, Tsukuba, Ibaraki 305-8506; Graduate School of Environmental Studies, Nagoya University, Furo-cho, Chikusa-ku, Nagoya City 464-8601

Research highlights: {yields} Urban symbiosis creates compatibility of industrial development and waste management. {yields} Mechanical technology leads to more CO{sub 2} emission reduction. {yields} Energy recovery technology leads to more fossil fuel saving. {yields} Clean energy makes recycling technologies cleaner. {yields} Demand management is crucial for realizing potential environmental gains of recycling. - Abstract: With the increasing attention on developing a low-carbon economy, it is necessary to seek appropriate ways on reducing greenhouse gas (GHG) emissions through innovative municipal solid waste management (MSWM), such as urban symbiosis. However, quantitative assessments on the environmental benefits of urban symbiosis, especially in developingmore » countries, are limited because only a limited number of planned synergistic activities have been successful and it is difficult to acquire detailed inventory data from private companies. This paper modifies and applies a two-step simulation system and used it to assess the potential environmental benefits, including the reduction of GHG emissions and saving of fossil fuels, by employing various Japanese plastics recycling/energy-recovery technologies in Shenyang, China. The results showed that among various recycling/energy-recovery technologies, the mechanical waste plastics recycling technology, which produces concrete formwork boards (NF boards), has the greatest potential in terms of reducing GHG emissions (1.66 kg CO{sub 2}e/kg plastics), whereas the technology for the production of refuse plastic fuel (RPF) has the greatest potential on saving fossil fuel consumption (0.77 kgce/kg-plastics). Additional benefits can be gained by applying combined technologies that cascade the utilization of waste plastics. Moreover, the development of clean energy in conjunction with the promotion of new waste plastics recycling programs could contribute to additional reductions in GHG emissions and fossil fuel consumption.« less

Towards increased recycling of household waste: Documenting cascading effects and material efficiency of commingled recyclables and biowaste collection.

PubMed

Cimpan, Ciprian; Rothmann, Marianne; Hamelin, Lorie; Wenzel, Henrik

2015-07-01

Municipal solid waste (MSW) management remains a challenge, even in Europe where several countries now possess capacity to treat all arising MSW, while others still rely on unsustainable disposal pathways. In the former, strategies to reach higher recycling levels are affecting existing waste-to-energy (WtE) treatment infrastructure, by inducing additional overcapacity and this in turn rebounds as pressure on the waste and recyclable materials markets. This study addresses such situations by documenting the effects, in terms of resource recovery, global warming potential (GWP) and cumulative energy demand (CED), of a transition from a self-sufficient waste management system based on minimal separate collection and efficient WtE, towards a system with extended separate collection of recyclable materials and biowaste. In doing so, it tackles key questions: (1) whether recycling and biological treatment are environmentally better compared to highly efficient WtE, and (2) what are the implications of overcapacity-related cascading effects, namely waste import, when included in the comparison of alternative waste management systems. System changes, such as the implementation of kerbside separate collection of recyclable materials were found to significantly increase material recovery, besides leading to substantial GWP and CED savings in comparison to the WtE-based system. Bio-waste separate collection contributed with additional savings when co-digested with manure, and even more significantly when considering future renewable energy background systems reflecting the benefits induced by the flexible use of biogas. Given the current liberalization of trade in combustible waste in Europe, waste landfilling was identified as a short-to-medium-term European-wide waste management marginal reacting to overcapacity effects induced by the implementation of increased recycling strategies. When waste import and, consequently, avoided landfilling were included in the system boundary, additional savings of up to 700 kg CO2 eq. and 16 GJ eq. of primary energy per tonne of imported waste were established. Conditions, such as energy recovery efficiency, and thresholds beyond which import-related savings potentially turn into GWP burdens were also determined. Copyright © 2015 Elsevier Ltd. All rights reserved.

Aerosol corrosion prevention and energy-saving strategies in the design of green data centers.

PubMed

Ferrero, Luca; Sangiorgi, Giorgia; Ferrini, Barbara S; Perrone, Maria G; Moscatelli, Marco; D'Angelo, Luca; Rovelli, Grazia; Ariatta, Alberto; Truccolo, Redy; Bolzacchini, Ezio

2013-04-16

The energy demands of data centers (DCs) worldwide are rapidly increasing, as are their environmental and economic costs. This paper presents a study conducted at Sannazzaro de' Burgondi (Po Valley), Italy, specifically aimed at optimizing the operating conditions of a DC designed for the Italian Oil and Gas Company (Eni) (5200 m(2) of Information Technology installed, 30 MW) and based on a direct free cooling (DFC) system. The aim of the study was to save the largest possible quantity of energy, while at the same time preventing aerosol corrosion. The aerosol properties (number size distribution, chemical composition, deliquescence relative humidity (DRH), acidity) and meteorological parameters were monitored and utilized to determine the potential levels of aerosol entering the DC (equivalent ISO class), together with its DRH. These data enabled us both to select the DC's filtering system (MERV13 filters) and to optimize the cooling cycle through calculation of the most reliable humidity cycle (60% of maximum allowed RH) applicable to the DFC. A potential energy saving of 81%, compared to a traditional air conditioning cooling system, was estimated: in one year, for 1 kW of installed information technology, the estimated energy saving is 7.4 MWh, resulting in 2.7 fewer tons of CO2 being emitted, and a financial saving of € 1100.

A taxonomy of hospitals participating in Medicare accountable care organizations.

PubMed

Bazzoli, Gloria J; Harless, David W; Chukmaitov, Askar S

2017-03-03

Medicare was an early innovator of accountable care organizations (ACOs), establishing the Medicare Shared Savings Program (MSSP) and Pioneer programs in 2012-2013. Existing research has documented that ACOs bring together an array of health providers with hospitals serving as important participants. Hospitals vary markedly in their service structure and organizational capabilities, and thus, one would expect hospital ACO participants to vary in these regards. Our research identifies hospital subgroups that share certain capabilities and competencies. Such research, in conjunction with existing ACO research, provides deeper understanding of the structure and operation of these organizations. Given that Medicare was an initiator of the ACO concept, our findings provide a baseline to track the evolution of ACO hospitals over time. Hierarchical clustering methods are used in separate analyses of MSSP and Pioneer ACO hospitals. Hospitals participating in ACOs with 2012-2013 start dates are identified through multiple sources. Study data come from the Centers for Medicare and Medicaid Services, American Hospital Association, and Health Information and Management Systems Society. Five-cluster solutions were developed separately for the MSSP and Pioneer hospital samples. Both the MSSP and Pioneer taxonomies had several clusters with high levels of health information technology capabilities. Also distinct clusters with strong physician linkages were present. We examined Pioneer ACO hospitals that subsequently left the program and found that they commonly had low levels of ambulatory care services or health information technology. Distinct subgroups of hospitals exist in both the MSSP and Pioneer programs, suggesting that individual hospitals serve different roles within an ACO. Health information technology and physician linkages appear to be particularly important features in ACO hospitals. ACOs need to consider not only geographic and service mix when selecting hospital participants but also their vertical integration features and management competencies.

Scientific Inquiry into Home Electronic Technology Usage

ERIC Educational Resources Information Center

Lazaros, Edward J.; Spotts, Thomas H.; Verdon, Jessica E.

2010-01-01

This activity promotes ways to save electricity in the home. Students identify electronic devices in the home and examine wattage, hours of use per month, estimated wattage per month, kilowatt hours per month, average retail price per kilowatt hour in each state, and the estimated cost per month. Students gain an appreciation for how saving power…

Tool to Prioritize Energy Efficiency Investments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Farese, P.; Gelman, R.; Hendron, R.

2012-08-01

To provide analytic support of the U.S. Department of Energy's Office of the Building Technology Program (BTP), NREL developed a Microsoft Excel-based tool to provide an open and objective comparison of the hundreds of investment opportunities available to BTP. This tool uses established methodologies to evaluate the energy savings and cost of those savings.

Why Cool Roofs?

ScienceCinema

Chu, Steven

2017-12-27

By installing a cool roof at DOE, the federal government and Secretary Chu are helping to educate families and businesses about the important energy and cost savings that can come with this simple, low-cost technology. Cool roofs have the potential to quickly and dramatically reduce global carbon emissions while saving money every month on consumers' electrical bills.

Green Energy in New Construction: Maximize Energy Savings and Minimize Cost

ERIC Educational Resources Information Center

Ventresca, Joseph

2010-01-01

People often use the term "green energy" to refer to alternative energy technologies. But green energy doesn't guarantee maximum energy savings at a minimum cost--a common misconception. For school business officials, green energy means getting the lowest energy bills for the lowest construction cost, which translates into maximizing green energy…

The Impact of DOE Building Technology Energy Efficiency Programs on U.S. Employment, Income, and Investment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Scott, Michael J.; Roop, Joseph M.; Schultz, Robert W.

2008-07-31

To more fully evaluate its programs to increase the energy efficiency of the U.S. residential and commercial building stock, the U.S. Department of Energy’s Office of Energy Efficiency and Renewable Energy (EERE) assesses the macroeconomic impacts of those programs, specifically on national employment, wage income, and (most recently) investment. The analysis is conducted using the Impact of Sector Energy Technologies (ImSET) model, a special-purpose 188-sector input-output model of the U.S. economy designed specifically to evaluate the impacts of energy efficiency investments and saving. For the analysis described in the paper, ImSET was amended to provide estimates of sector-by-sector capital requirementsmore » and investment. In the scenario of the Fiscal Year (FY) 2005 Buildings Technology (BT) program, the technologies and building practices being developed and promoted by the BT program have the prospect of saving about 2.9×1015 Btu in buildings by the year 2030, about 27% of the expected growth in buildings energy consumption by the year 2030. The analysis reported in the paper finds that, by the year 2030, these savings have the potential to increase employment by up to 446,000 jobs, increase wage income by $7.8 billion, reduce needs for capital stock in the energy sector and closely related supporting industries by about $207 billion (and the corresponding annual level of investment by $13 billion), and create net capital savings that are available to grow the nation’s future economy.« less

Design methodology for integrated downstream separation systems in an ethanol biorefinery

NASA Astrophysics Data System (ADS)

Mohammadzadeh Rohani, Navid

Energy security and environmental concerns have been the main drivers for a historic shift to biofuel production in transportation fuel industry. Biofuels should not only offer environmental advantages over the petroleum fuels they replace but also should be economically sustainable and viable. The so-called second generation biofuels such as ethanol which is the most produced biofuel are mostly derived from lignocellulosic biomasses. These biofuels are more difficult to produce than the first generation ones mainly due to recalcitrance of the feedstocks in extracting their sugar contents. Costly pre-treatment and fractionation stages are required to break down lignocellulosic feedstocks into their constituent elements. On the other hand the mixture produced in fermentation step in a biorefinery contains very low amount of product which makes the subsequent separation step more difficult and more energy consuming. In an ethanol biorefinery, the dilute fermentation broth requires huge operating cost in downstream separation for recovery of the product in a conventional distillation technique. Moreover, the non-ideal nature of ethanol-water mixture which forms an iseotrope at almost 95 wt%, hinders the attainment of the fuel grade ethanol (99.5 wt%). Therefore, an additional dehydration stage is necessary to purify the ethanol from its azeotropic composition to fuel-grade purity. In order to overcome the constraint pertaining to vapor-liquid equilibrium of ethanol-water separation, several techniques have been investigated and proposed in the industry. These techniques such as membrane-based technologies, extraction and etc. have not only sought to produce a pure fuel-grade ethanol but have also aimed at decreasing the energy consumption of this energy-intensive separation. Decreasing the energy consumption of an ethanol biorefinery is of paramount importance in improving its overall economics and in facilitating the way to displacing petroleum transportation fuel and obtaining energy security. On the other hand, Process Integration (PI) as defined by Natural Resource Canada as the combination of activities which aim at improving process systems, their unit operations and their interactions in order to maximize the efficiency of using water, energy and raw materials can also help biorefineries lower their energy consumptions and improve their economics. Energy integration techniques such as pinch analysis adopted by different industries over the years have ensured using heat sources within a plant to supply the demand internally and decrease the external utility consumption. Therefore, adopting energy integration can be one of the ways biorefinery technology owners can consider in their process development as well as their business model in order to improve their overall economics. The objective of this thesis is to propose a methodology for designing integrated downstream separation in a biorefinery. This methodology is tested in an ethanol biorefinery case study. Several alternative separation techniques are evaluated in their energy consumption and economics in three different scenarios; stand-alone without energy integration, stand-alone with internal energy integration and integrated-with Kraft. The energy consumptions and capital costs of separation techniques are assessed in each scenario and the cost and benefit of integration are determined and finally the best alternative is found through techno-economic metrics. Another advantage of this methodology is the use of a graphical tool which provides insights on decreasing energy consumption by modifying the process condition. The pivot point of this work is the use of a novel energy integration method called Bridge analysis. This systematic method which originally is intended for retrofit situation is used here for integration with Kraft process. Integration potentials are identified through this method and savings are presented for each design. In stand-alone with internal integration scenario, the conventional pinch method is used for energy analysis. The results reveal the importance of energy integration in reducing energy consumption. They also show that in an ethanol biorefinery, by adopting energy integration in the conventional distillation separation, we can achieve greater energy saving compared to other alternative techniques. This in turn suggests that new alternative technologies which imply big risks for the company might not be an option for reducing the energy consumption as long as an internal and external integration is incorporated in the business model of an ethanol biorefinery. It is also noteworthy that the methodology developed in this work can be extended as a future work to include a whole biorefinery system. (Abstract shortened by UMI.).

Extending cost–benefit analysis for the sustainability impact of inter-urban Intelligent Transport Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kolosz, Ben, E-mail: kolosz27@gmail.com; Grant-Muller, Susan, E-mail: S.M.Grant-Muller@its.leeds.ac.uk

The paper reports research involving three cost–benefit analyses performed on different ITS schemes (Active Traffic Management, Intelligent Speed Adaptation and the Automated Highway System) on one of the UK's busiest highways — the M42. The environmental scope of the assets involved is widened to take into account the possibility of new technology linked by ICT and located within multiple spatial regions. The areas focused on in the study were data centre energy emissions, the embedded emissions of the road-side infrastructure, vehicle tailpipe emissions, additional hardware required by the vehicles (if applicable) and safety, and all aspects of sustainability. Dual discountingmore » is applied which aims to provide a separate discount rate for environmental elements. For ATM, despite the energy costs of the data centre, the initial implementation costs and mitigation costs of its embedded emissions, a high cost–benefit ratio of 5.89 is achieved, although the scheme becomes less effective later on its lifecycle due to rising costs of energy. ISA and AHS generate a negative result, mainly due to the cost of getting the vehicle on the road. In order to negate these costs, the pricing of the vehicle should be scaled depending upon the technology that is outfitted. Retrofitting on vehicles without the technology should be paid for by the driver. ATM will offset greenhouse gas emissions by 99 kt of CO{sub 2} equivalency over a 25 year lifespan. This reduction has taken into account the expected improvement in vehicle technology. AHS is anticipated to save 280 kt of CO{sub 2} equivalency over 15 years of operational usage. However, this offset is largely dependent on assumptions such as the level of market penetration. - Highlights: • Three cost–benefit analyses are applied to inter-urban intelligent transport. • For ATM, a high cost–benefit ratio of 5.89 is achieved. • ATM offsets greenhouse gas emissions by 99 kt of CO{sub 2} equivalency over 25 years. • ISA and AHS generate a negative result due to vehicle implementation costs. • AHS is anticipated to save 280 kt of CO{sub 2} equivalency over 15 years.« less

Motives for Acquiring and Saving in Hoarding Disorder, OCD, and Community Controls

PubMed Central

Frost, Randy O.; Steketee, Gail; Tolin, David F.; Sinopoli, Nicole; Ruby, Dylan

2015-01-01

Hoarding Disorder (HD) was classified as a separate disorder in DSM-5 (APA, 2013). However, only recently has research on hoarding begun in earnest, and as of yet, very little research exists on the motivation to acquire and save the excessive volume of possessions seen in patients with this disorder. This investigation examined the frequency of four motives for acquiring and saving possessions that are often reported anecdotally by people with HD (information, emotional reasons, avoid waste, and aesthetic reasons). Comparisons in a sample of 443 participants indicated that those with HD reported higher frequencies of each of these four motives for acquiring and saving compared to OCD participants and community controls. The intention to avoid waste emerged as the most prominent motive in people with HD. Understanding waste avoidance may be key to better understanding and treating HD. PMID:25729641

Cost Savings from Palliative Care Teams and Guidance for a Financially Viable Palliative Care Program

PubMed Central

McCarthy, Ian M; Robinson, Chessie; Huq, Sakib; Philastre, Martha; Fine, Robert L

2015-01-01

Objectives To quantify the cost savings of palliative care (PC) and identify differences in savings according to team structure, patient diagnosis, and timing of consult. Data Sources Hospital administrative records on all inpatient stays at five hospital campuses from January 2009 through June 2012. Study Design The analysis matched PC patients to non-PC patients (separately by discharge status) using propensity score methods. Weighted generalized linear model regressions of hospital costs were estimated for the matched groups. Data Collection Data were restricted to patients at least 18 years old with inpatient stays of between 7 and 30 days. Variables available included patient demographics, primary and secondary diagnoses, hospital costs incurred for the inpatient stay, and when/if the patient had a PC consult. Principal Findings We found overall cost savings from PC of $3,426 per patient for those dying in the hospital. No significant cost savings were found for patients discharged alive; however, significant cost savings for patients discharged alive could be achieved for certain diagnoses, PC team structures, or if consults occurred within 10 days of admission. Conclusions Appropriately selected and timed PC consults with physician and RN involvement can help ensure a financially viable PC program via cost savings to the hospital. PMID:25040226

Panel I: Technology and Jobs.

ERIC Educational Resources Information Center

Appalachia, 1984

1984-01-01

Panel I features two case histories of state government, university, and private corporation cooperation to bring technology to the workplace (Microelectronics Center of North Carolina and Ben Franklin Partnership Program) and presentations about Burlington Industries and General Electric Company investments in technology to save jobs and boost…

Motion control of multi-actuator hydraulic systems for mobile machineries: Recent advancements and future trends

NASA Astrophysics Data System (ADS)

Xu, Bing; Cheng, Min

2018-06-01

This paper presents a survey of recent advancements and upcoming trends in motion control technologies employed in designing multi-actuator hydraulic systems for mobile machineries. Hydraulic systems have been extensively used in mobile machineries due to their superior power density and robustness. However, motion control technologies of multi-actuator hydraulic systems have faced increasing challenges due to stringent emission regulations. In this study, an overview of the evolution of existing throttling control technologies is presented, including open-center and load sensing controls. Recent advancements in energy-saving hydraulic technologies, such as individual metering, displacement, and hybrid controls, are briefly summarized. The impact of energy-saving hydraulic technologies on dynamic performance and control solutions are also discussed. Then, the advanced operation methods of multi-actuator mobile machineries are reviewed, including coordinated and haptic controls. Finally, challenges and opportunities of advanced motion control technologies are presented by providing an overall consideration of energy efficiency, controllability, cost, reliability, and other aspects.

The impact of labor-saving technology on first birth intervals in rural Ethiopia.

PubMed

Gibson, Mhairi; Mace, Ruth

2002-02-01

Across the developing world labor-saving technologies introduce considerable savings in the time and energy that women allocate to work. Hormonal studies on natural fertility populations indicate that such a reduction in energetic expenditure (rather than improved nutritional status alone) can lead to increased ovarian function. Other qualitative studies have highlighted a link between labor-saving technology and behavioral changes affecting subsequent age at marriage, which may affect fertility. This biodemographic study was designed to investigate whether these physiological and behavioral changes affect fertility at a population level by focusing on a recent water development scheme in Southern Ethiopia. The demographic consequences of a reduction in women's workload following the installation of water points, specifically the variation in length of first birth interval (time lapsed between marriage and first birth), are investigated. First birth interval length is closely associated with lifetime fertility in populations that do not practice contraception, longer intervals being associated with lower fertility. Using life tables and multivariate hazard modeling techniques a number of significant predictors of first birth interval length are identified. Covariates such as age at marriage, season of marriage, village ecology, and access to improved water supply have significant effects on variation in first birth intervals. When entered into models as a time-varying covariate, access to a water tap stand is associated with an immediate reduction in length of first birth intervals.

Economic Analysis of the Reduction of Blood Transfusions during Surgical Procedures While Continuous Hemoglobin Monitoring Is Used

PubMed Central

Ribed-Sánchez, Borja; Varea-Díaz, Sara; Corbacho-Fabregat, Carlos; Pérez-Oteyza, Jaime; Belda-Iniesta, Cristóbal

2018-01-01

Background: Two million transfusions are performed in Spain every year. These come at a high economic price for the health system, increasing the morbidity and mortality rates. The way of obtaining the hemoglobin concentration value is via invasive and intermittent methods, the results of which take time to obtain. The drawbacks of this method mean that some transfusions are unnecessary. New continuous noninvasive hemoglobin measurement technology can save unnecessary transfusions. Methods: A prospective study was carried out with a historical control of two homogeneous groups. The control group used the traditional hemoglobin measurement methodology. The experimental group used the new continuous hemoglobin measurement technology. The difference was analyzed by comparing the transfused units of the groups. The economic savings was calculated by multiplying the cost of a transfusion by the difference in units, taking into account measurement costs. Results: The percentage of patients needing a transfusion decreased by 7.4%, and the number of transfused units per patient by 12.56%. Economic savings per patient were €20.59. At the national level, savings were estimated to be 13,500 transfusions (€1.736 million). Conclusions: Constant monitoring of the hemoglobin level significantly reduces the need for blood transfusions. By using this new measurement technology, health care facilities can significantly reduce costs and improve care quality. PMID:29702617

Energy and cost savings results for advanced technology systems from the Cogeneration Technology Alternatives Study /CTAS/

NASA Technical Reports Server (NTRS)

Sagerman, G. D.; Barna, G. J.; Burns, R. K.

1979-01-01

The Cogeneration Technology Alternatives Study (CTAS), a program undertaken to identify the most attractive advanced energy conversion systems for industrial cogeneration applications in the 1985-2000 time period, is described, and preliminary results are presented. Two cogeneration options are included in the analysis: a topping application, in which fuel is input to the energy conversion system which generates electricity and waste heat from the conversion system is used to provide heat to the process, and a bottoming application, in which fuel is burned to provide high temperature process heat and waste heat from the process is used as thermal input to the energy conversion system which generates energy. Steam turbines, open and closed cycle gas turbines, combined cycles, diesel engines, Stirling engines, phosphoric acid and molten carbonate fuel cells and thermionics are examined. Expected plant level energy savings, annual energy cost savings, and other results of the economic analysis are given, and the sensitivity of these results to the assumptions concerning fuel prices, price of purchased electricity and the potential effects of regional energy use characteristics is discussed.

Technology Prioritization: Transforming the U.S. Building Stock to Embrace Energy Efficiency

DOE Office of Scientific and Technical Information (OSTI.GOV)

Abdelaziz, Omar; Farese, Philip; Abramson, Alexis

2013-01-01

The U.S. Buildings sector is responsible for about 40% of the national energy expenditures. This is due in part to wasteful use of resources and limited considerations made for energy efficiency during the design and retrofit phases. Recent studies have indicated the potential for up to 30-50% energy savings in the U.S. buildings sector using currently available technologies. This paper discusses efforts to accelerate the transformation in the U.S. building energy efficiency sector using a new technology prioritization framework. The underlying analysis examines building energy use micro segments using the Energy Information Administration Annual Energy Outlook and other publically availablemore » information. The tool includes a stock-and-flow model to track stock vintage and efficiency levels with time. The tool can be used to investigate energy efficiency measures under a variety of scenarios and has a built-in energy accounting framework to prevent double counting of energy savings within any given portfolio. This tool is developed to inform decision making and estimate long term potential energy savings for different market adoption scenarios.« less

Solar thermal technology development: Estimated market size and energy cost savings. Volume 2: Assumptions, methodology and results

NASA Astrophysics Data System (ADS)

Gates, W. R.

1983-02-01

Estimated future energy cost savings associated with the development of cost-competitive solar thermal technologies (STT) are discussed. Analysis is restricted to STT in electric applications for 16 high-insolation/high-energy-price states. Three fuel price scenarios and three 1990 STT system costs are considered, reflecting uncertainty over future fuel prices and STT cost projections. Solar thermal technology research and development (R&D) is found to be unacceptably risky for private industry in the absence of federal support. Energy cost savings were projected to range from $0 to $10 billion (1990 values in 1981 dollars), depending on the system cost and fuel price scenario. Normal R&D investment risks are accentuated because the Organization of Petroleum Exporting Countries (OPEC) cartel can artificially manipulate oil prices and undercut growth of alternative energy sources. Federal participation in STT R&D to help capture the potential benefits of developing cost-competitive STT was found to be in the national interest. Analysis is also provided regarding two federal incentives currently in use: The Federal Business Energy Tax Credit and direct R&D funding.

Solar thermal technology development: Estimated market size and energy cost savings. Volume 2: Assumptions, methodology and results

NASA Technical Reports Server (NTRS)

Gates, W. R.

1983-01-01

Estimated future energy cost savings associated with the development of cost-competitive solar thermal technologies (STT) are discussed. Analysis is restricted to STT in electric applications for 16 high-insolation/high-energy-price states. Three fuel price scenarios and three 1990 STT system costs are considered, reflecting uncertainty over future fuel prices and STT cost projections. Solar thermal technology research and development (R&D) is found to be unacceptably risky for private industry in the absence of federal support. Energy cost savings were projected to range from $0 to $10 billion (1990 values in 1981 dollars), depending on the system cost and fuel price scenario. Normal R&D investment risks are accentuated because the Organization of Petroleum Exporting Countries (OPEC) cartel can artificially manipulate oil prices and undercut growth of alternative energy sources. Federal participation in STT R&D to help capture the potential benefits of developing cost-competitive STT was found to be in the national interest. Analysis is also provided regarding two federal incentives currently in use: The Federal Business Energy Tax Credit and direct R&D funding.

Performance and economic evaluation of the seahorse natural gas hot water heater conversion at Fort Stewart. Interim report, 1994 Summer

DOE Office of Scientific and Technical Information (OSTI.GOV)

Winiarski, D.W.

1995-01-01

The federal government is the largest single energy consumer in the United States cost valued at nearly $10 billion annually. The US Department of Energy`s (DOE) Federal Energy Management Program (FEMP) supports efforts to reduce energy use and associated expenses in the federal sector. One such effort, the New Technology Demonstration Program (NTDP), seeks to evaluate new energy-saving US technologies and secure their more timely adoption by the US government. Pacific Northwest Laboratory (PNL) is one of four DOE laboratories that participate in the New Technologies Demonstration Program, providing technical expertise and equipment to evaluate new, energy-saving technologies being studiedmore » under that program. This interim report provides the results of a field evaluation that PNL conducted for DOE/FEMP and the US Department of Defense (DoD) Strategic Environmental Research and Development Program (SERDP) to examine the performance of a candidate energy-saving technology-a hot water heater conversion system to convert electrically heated hot water tanks to natural gas fuel. The unit was installed at a single residence at Fort Stewart, a US Army base in Georgia, and the performance was monitored under the NTDP. Participating in this effort under a Cooperative Research and Development Agreement (CRADA) were Gas Fired Products, developers of the technology; the Public Service Company of North Carolina; Atlanta Gas Light Company; the Army Corps of Engineers; Fort Stewart; and Pacific Northwest Laboratory.« less

Advanced technology commercial fuselage structure

NASA Technical Reports Server (NTRS)

Ilcewicz, L. B.; Smith, P. J.; Walker, T. H.; Johnson, R. W.

1991-01-01

Boeing's program for Advanced Technology Composite Aircraft Structure (ATCAS) has focused on the manufacturing and performance issues associated with a wide body commercial transport fuselage. The primary goal of ATCAS is to demonstrate cost and weight savings over a 1995 aluminum benchmark. A 31 foot section of fuselage directly behind the wing to body intersection was selected for study purposes. This paper summarizes ATCAS contract plans and review progress to date. The six year ATCAS program will study technical issues for crown, side, and keel areas of the fuselage. All structural details in these areas will be included in design studies that incorporate a design build team (DBT) approach. Manufacturing technologies will be developed for concepts deemed by the DBT to have the greatest potential for cost and weight savings. Assembly issues for large, stiff, quadrant panels will receive special attention. Supporting technologies and mechanical tests will concentrate on the major issues identified for fuselage. These include damage tolerance, pressure containment, splices, load redistribution, post-buckled structure, and durability/life. Progress to date includes DBT selection of baseline fuselage concepts; cost and weight comparisons for crown panel designs; initial panel fabrication for manufacturing and structural mechanics research; and toughened material studies related to keel panels. Initial ATCAS studies have shown that NASA's Advanced Composite Technology program goals for cost and weight savings are attainable for composite fuselage.

Spectra Optia® for Automated Red Blood Cell Exchange in Patients with Sickle Cell Disease: A NICE Medical Technology Guidance.

PubMed

Willits, Iain; Cole, Helen; Jones, Roseanne; Carter, Kimberley; Arber, Mick; Jenks, Michelle; Craig, Joyce; Sims, Andrew

2017-08-01

The Spectra Optia ® automated apheresis system, indicated for red blood cell exchange in people with sickle cell disease, underwent evaluation by the National Institute for Health and Care Excellence, which uses its Medical Technologies Advisory Committee to make recommendations. The company (Terumo Medical Corporation) produced a submission making a case for adoption of its technology, which was critiqued by the Newcastle and York external assessment centre. Thirty retrospective observational studies were identified in their clinical submission. The external assessment centre considered these were of low methodological and reporting quality. Most were single-armed studies, with only six studies providing comparative data. The available data showed that, compared with manual red blood cell exchange, Spectra Optia reduces the frequency of exchange procedures as well as their duration, but increases the requirement for donor blood. However, other clinical and patient benefits were equivocal because of an absence of robust clinical evidence. The company provided a de novo model to support the economic proposition of the technology, and reported that in most scenarios Spectra Optia was cost saving, primarily through reduced requirement of chelation therapy to manage iron overload. The external assessment centre considered that although the cost-saving potential of Spectra Optia was plausible, the model and its clinical inputs were not sufficiently robust to demonstrate this. However, taking the evidence together with expert and patient advice, the Medical Technologies Advisory Committee considered Spectra Optia was likely to save costs, provide important patient benefits, and reduce inequality, and gave the technology a positive recommendation in Medical Technology Guidance 28.

Energy-Saving Optimization of Water Supply Pumping Station Life Cycle Based on BIM Technology

NASA Astrophysics Data System (ADS)

Qun, Miao; Wang, Jiayuan; Liu, Chao

2017-12-01

In the urban water supply system, pump station is the main unit of energy consumption. In the background of pushing forward the informatization in China, using BIM technology in design, construction and operations of water supply pumping station, can break through the limitations of the traditional model and effectively achieve the goal of energy conservation and emissions reduction. This work researches the way to solve energy-saving optimization problems in the process of whole life cycle of water supply pumping station based on BIM technology, and put forward the feasible strategies of BIM application in order to realize the healthy and sustainable development goals by establishing the BIM model of water supply pumping station of Qingdao Guzhenkou water supply project.

A method for the analysis of the benefits and costs for aeronautical research and technology

NASA Technical Reports Server (NTRS)

Williams, L. J.; Hoy, H. H.; Anderson, J. L.

1978-01-01

A relatively simple, consistent, and reasonable methodology for performing cost-benefit analyses which can be used to guide, justify, and explain investments in aeronautical research and technology is presented. The elements of this methodology (labeled ABC-ART for the Analysis of the Benefits and Costs of Aeronautical Research and Technology) include estimation of aircraft markets; manufacturer costs and return on investment versus aircraft price; airline costs and return on investment versus aircraft price and passenger yield; and potential system benefits--fuel savings, cost savings, and noise reduction. The application of this methodology is explained using the introduction of an advanced turboprop powered transport aircraft in the medium range market in 1978 as an example.

Resistively-Heated Microlith-based Adsorber for Carbon Dioxide and Trace Contaminant Removal

NASA Technical Reports Server (NTRS)

Roychoudhury, S.; Walsh, D.; Perry, J.

2005-01-01

An integrated sorber-based Trace Contaminant Control System (TCCS) and Carbon Dioxide Removal Assembly (CDRA) prototype was designed, fabricated and tested. It corresponds to a 7-person load. Performance over several adsorption/regeneration cycles was examined. Vacuum regenerations at effective time/temperature conditions, and estimated power requirements were experimentally verified for the combined CO2/trace contaminant removal prototype. The current paper details the design and performance of this prototype during initial testing at CO2 and trace contaminant concentrations in the existing CDRA, downstream of the drier. Additional long-term performance characterization is planned at NASA. Potential system design options permitting associated weight, volume savings and logistic benefits, especially as relevant for long-duration space flight, are reviewed. The technology consisted of a sorption bed with sorbent- coated metal meshes, trademarked and patented as Microlith by Precision Combustion, Inc. (PCI). By contrast the current CO2 removal system on the International Space Station employs pellet beds. Preliminary bench scale performance data (without direct resistive heating) for simultaneous CO2 and trace contaminant removal was reviewed in SAE 2004-01-2442. In the prototype, the meshes were directly electrically heated for rapid response and accurate temperature control. This allowed regeneration via resistive heating with the potential for shorter regeneration times, reduced power requirement, and net energy savings vs. conventional systems. A novel flow arrangement, for removing both CO2 and trace contaminants within the same bed, was demonstrated. Thus, the need for a separate trace contaminant unit was eliminated resulting in an opportunity for significant weight savings. Unlike the current disposable charcoal bed, zeolites for trace contaminant removal are amenable to periodic regeneration.

Energy-Efficient and Comfortable Buildings through Multivariate Integrated Control (ECoMIC)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Birru, Dagnachew; Wen, Yao-Jung; Rubinstein, Francis M.

2013-10-28

This project aims to develop an integrated control solution for enhanced energy efficiency and user comfort in commercial buildings. The developed technology is a zone-based control framework that minimizes energy usage while maintaining occupants’ visual and thermal comfort through control of electric lights, motorized venetian blinds and thermostats. The control framework is designed following a modular, scalable and flexible architecture to facilitate easy integration with exiting building management systems. The control framework contains two key algorithms: 1) the lighting load balancing algorithm and 2) the thermostat control algorithm. The lighting load balancing algorithm adopts a model-based closed-loop control approach tomore » determine the optimal electric light and venetian blind settings. It is formulated into an optimization problem with minimizing lighting-related energy consumptions as the objective and delivering adequate task light and preventing daylight glare as the constraints. The thermostat control algorithm is based on a well-established thermal comfort model and formulated as a root-finding problem to dynamically determine the optimal thermostat setpoint for both energy savings and improved thermal comfort. To address building-wide scalability, a system architecture was developed for the zone-based control technology. Three levels of services are defined in the architecture: external services, facility level services and zone level services. The zone-level service includes the control algorithms described above as well as the corresponding interfaces, profiles, sensors and actuators to realize the zone controller. The facility level services connect to the zones through a backbone network, handle supervisory level information and controls, and thus facilitate building-wide scalability. The external services provide communication capability to entities outside of the building for grid interaction and remote access. Various aspects of the developed control technology were evaluated and verified through both simulations and testbed implementations. Simulations coupling a DOE medium office reference building in EnergyPlus building simulation software and a prototype controller in Matlab were performed. During summer time in a mixed-humid climate zone, the simulations revealed reductions of 27% and 42% in electric lighting load and cooling load, respectively, when compared to an advanced base case with daylight dimming and blinds automatically tilted to block direct sun. Two single-room testbeds were established. The testbed at Philips Lighting business building (Rosemont, IL) was designed for quantifying energy performance of integrated controls. This particular implementation achieved 40% and 79% savings on lighting and HVAC energy, respectively, compared to a relatively simple base case operated on predefined schedules. While the resulting energy savings was very encouraging, it should be noted that there may be several caveats associated with it. 1) The test was run during late spring and early summer, and the savings numbers might not be directly used to extrapolate the annual energy savings. 2) Due to the needs for separate control and metering of the small-scale demonstrator within a large building, the HVAC system, hence the corresponding savings, did not represent a typical energy code-compliant design. 3) The light level in the control case was regulated at a particular setpoint, which was lower than then the full-on light level in the base case, and the savings resulted from tuning down the light level to the setpoint was not attributable to the contribution of the developed technology. The testbed at the Lawrence Berkeley National Laboratory (Berkeley, CA) specifically focused on glare control integration, and has demonstrated the feasibility and capability of the glare detection and prevention technique. While the short one-month test in this testbed provided a functional indication of the developed technology, and it would require at least a full solstice-to-solstice cycle to ruinously quantify the performance, which was not possible within the project timeframe. There are certain limitations inherited from the operational assumptions, which could potentially affect the effectiveness and applicability of the developed control technologies. The system takes a typical ceiling-mounting approach for the photosensor locations, and therefore, the control performance relies on proper commissioning or the built-in intelligence of the photosensor for pertinent task light level estimations. For spaces where daylight penetration diminishes significantly deeper into the zone, certain modification to the control algorithms is required to accommodate multiple lighting control subzones and the corresponding sensors for providing a more uniform light level across the entire zone. Integrated control of visual and thermal comfort requires the lighting control zone and thermal control zone to coincide with each other. In other words, the area illuminated by a lighting circuit needs to be the same area served by the thermostat. Thus, the original zoning will potentially constrain the applicability of this technology in retrofitting projects. This project demonstrated the technical feasibility of a zone-based integrated control technology. From the simulation results and testbed implementations, up to 60% lighting energy savings in daylit areas relative to a “no-controls” case can easily be achieved. A 20% reduction of whole building energy consumption is also attainable. In the aspect of occupant comfort, the testbed demonstrated the ability to maintain specified light level on the workplane while promptly mitigate daylight glare 90% of the time. The control system also managed to maintain the thermal environment at a comfortable level 90% of the time. The aspect of system scalability was guaranteed by the system architecture design, based on which the testbeds were instantiated. Analysis on the aspect of economic benefit has yielded an about 6-year payback time for a medium-sized building, including the installation of all hardware and software, such as motorized blinds and LED luminaires. The payback time can be significantly reduced if part of the hardware is already in place for retrofitting projects. It needs to be noted that since the payback analysis was partly based on the testbed performance results, it is constrained by the caveats associated with the testbed implementations. The main uncertainty lies in the contribution from the space conditioning energy savings as it was non-trivial to realistically configure a room-size HVAC system for directly extrapolating whole-building HVAC energy savings. It is recommended to further evaluate the developed technology at a larger scale, where the lighting and HVAC energy consumption can be realistically measured at the building level, to more rigorously quantify the performance potentials.« less

Logistics Reduction Technologies for Exploration Missions

NASA Technical Reports Server (NTRS)

Broyan, James L., Jr.; Ewert, Michael K.; Fink, Patrick W.

2014-01-01

Human exploration missions under study are limited by the launch mass capacity of existing and planned launch vehicles. The logistical mass of crew items is typically considered separate from the vehicle structure, habitat outfitting, and life support systems. Although mass is typically the focus of exploration missions, due to its strong impact on launch vehicle and habitable volume for the crew, logistics volume also needs to be considered. NASA's Advanced Exploration Systems (AES) Logistics Reduction and Repurposing (LRR) Project is developing six logistics technologies guided by a systems engineering cradle-to-grave approach to enable after-use crew items to augment vehicle systems. Specifically, AES LRR is investigating the direct reduction of clothing mass, the repurposing of logistical packaging, the use of autonomous logistics management technologies, the processing of spent crew items to benefit radiation shielding and water recovery, and the conversion of trash to propulsion gases. Reduction of mass has a corresponding and significant impact to logistical volume. The reduction of logistical volume can reduce the overall pressurized vehicle mass directly, or indirectly benefit the mission by allowing for an increase in habitable volume during the mission. The systematic implementation of these types of technologies will increase launch mass efficiency by enabling items to be used for secondary purposes and improve the habitability of the vehicle as mission durations increase. Early studies have shown that the use of advanced logistics technologies can save approximately 20 m(sup 3) of volume during transit alone for a six-person Mars conjunction class mission.

Winglets Save Billions of Dollars in Fuel Costs

NASA Technical Reports Server (NTRS)

2010-01-01

The upturned ends now featured on many airplane wings are saving airlines billions of dollars in fuel costs. Called winglets, the drag-reducing technology was advanced through the research of Langley Research Center engineer Richard Whitcomb and through flight tests conducted at Dryden Flight Research Center. Seattle-based Aviation Partners Boeing -- a partnership between Aviation Partners Inc., of Seattle, and The Boeing Company, of Chicago -- manufactures Blended Winglets, a unique design featured on Boeing aircraft around the world. These winglets have saved more than 2 billion gallons of jet fuel to date, representing a cost savings of more than $4 billion and a reduction of almost 21.5 million tons in carbon dioxide emissions.

Conceptual Data Model for Administrative Functions of a Typical Naval Ship, to Include: Drug and Alcohol Program Advisor, Watch Quarter and Station Bill, Safety, Medical and Security

DTIC Science & Technology

1991-09-01

Secretary of Defense as a method to achieve savings in the $9 billion spent annually on information technology in DoD and to promote interoperability and...by the Office of the Secretary of Defense as a method to achieve savings in the $9 billion spent annually on information technology in DoD and to...commander. Without standard conventions for terminolo- gy, tactics or operations, the different units would have to expend much more time and effort to

Re-Building Greensburg

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hewitt, Steven; Wallach, Daniel; Peterson, Stephanie

2010-01-01

Greensburg, KS - A town that was devastated by a tornado in 2007, yet came back to be one of the Nation's most energy-efficient, sustainable communities. Civic leaders and entrepreneurs helped rally residents behind the idea of "greening" Greensburg, inspiring the construction of numerous energy-efficient buildings, some of which generate their own renewable power with solar panels and wind turbines. Many of the town's government buildings use cutting edge energy-saving technologies, saving the local taxpayers' money. Greensburg has demonstrated to the world that any city can reach its energy efficiency and renewable energy goals today using widely available technologies.

DigiMesh Reliability in High Speed Vehicular Applications

NASA Astrophysics Data System (ADS)

Visan, Bogdan A.

In a fast-paced technological society, advances in wireless networking show potential to save lives. Communication is key to notifying Emergency Medical Services of a potentially deadly accident in near real-time. This paper will discuss the use of low powered wireless devices transmitting life-saving information autonomously. Current and planned technologies used in vehicles are built-in, costly, and vulnerable to physical destruction. Using an independent system can offer both old and new vehicles primary and secondary communication. The results from this research study show that vehicles can use DigiMesh as a viable solution, although relative velocity affects its performance.

Re-Building Greensburg

ScienceCinema

Hewitt, Steven; Wallach, Daniel; Peterson, Stephanie

2017-12-09

Greensburg, KS - A town that was devastated by a tornado in 2007, yet came back to be one of the Nation's most energy-efficient, sustainable communities. Civic leaders and entrepreneurs helped rally residents behind the idea of "greening" Greensburg, inspiring the construction of numerous energy-efficient buildings, some of which generate their own renewable power with solar panels and wind turbines. Many of the town's government buildings use cutting edge energy-saving technologies, saving the local taxpayers' money. Greensburg has demonstrated to the world that any city can reach its energy efficiency and renewable energy goals today using widely available technologies.

Waste biorefineries: Enabling circular economies in developing countries.

PubMed

Nizami, A S; Rehan, M; Waqas, M; Naqvi, M; Ouda, O K M; Shahzad, K; Miandad, R; Khan, M Z; Syamsiro, M; Ismail, I M I; Pant, Deepak

2017-10-01

This paper aims to examine the potential of waste biorefineries in developing countries as a solution to current waste disposal problems and as facilities to produce fuels, power, heat, and value-added products. The waste in developing countries represents a significant source of biomass, recycled materials, chemicals, energy, and revenue if wisely managed and used as a potential feedstock in various biorefinery technologies such as fermentation, anaerobic digestion (AD), pyrolysis, incineration, and gasification. However, the selection or integration of biorefinery technologies in any developing country should be based on its waste characterization. Waste biorefineries if developed in developing countries could provide energy generation, land savings, new businesses and consequent job creation, savings of landfills costs, GHG emissions reduction, and savings of natural resources of land, soil, and groundwater. The challenges in route to successful implementation of biorefinery concept in the developing countries are also presented using life cycle assessment (LCA) studies. Copyright © 2017 Elsevier Ltd. All rights reserved.

Cogeneration technology alternatives study. Volume 1: Summary report

NASA Technical Reports Server (NTRS)

1980-01-01

Data and information in the area of advanced energy conversion systems for industrial congeneration applications in the 1985-2000 time period was studied. Six current and thirty-one advanced energy conversion systems were defined and combined with appropriate balance-of-plant equipment. Twenty-six industrial processes were selected from among the high energy consuming industries to serve as a framework for the study. Each conversion system was analyzed as a cogenerator with each industrial plant. Fuel consumption, costs, and environmental intrusion were evaluated and compared to corresponding traditional values. Various cogeneration strategies were analyzed and both topping and bottoming (using industrial by-product heat) applications were included. The advanced energy conversion technologies indicated reduced fuel consumption, costs, and emissions. Typically fuel energy savings of 10 to 25 percent were predicted compared to traditional on-site furnaces and utility electricity. With the variety of industrial requirements, each advanced technology had attractive applications. Overall, fuel cells indicated the greatest fuel energy savings and emission reductions. Gas turbines and combined cycles indicated high overall annual cost savings. Steam turbines and gas turbines produced high estimated returns. In some applications, diesels were most efficient. The advanced technologies used coal-derived fuels, or coal with advanced fluid bed combustion or on-site gasification systems.

Assessment of the greenhouse effect impact of technologies used for energy recovery from municipal waste: a case for England.

PubMed

Papageorgiou, A; Barton, J R; Karagiannidis, A

2009-07-01

Waste management activities contribute to global greenhouse gas emissions approximately by 4%. In particular the disposal of waste in landfills generates methane that has high global warming potential. Effective mitigation of greenhouse gas emissions is important and could provide environmental benefits and sustainable development, as well as reduce adverse impacts on public health. The European and UK waste policy force sustainable waste management and especially diversion from landfill, through reduction, reuse, recycling and composting, and recovery of value from waste. Energy from waste is a waste management option that could provide diversion from landfill and at the same time save a significant amount of greenhouse gas emissions, since it recovers energy from waste which usually replaces an equivalent amount of energy generated from fossil fuels. Energy from waste is a wide definition and includes technologies such as incineration of waste with energy recovery, or combustion of waste-derived fuels for energy production or advanced thermal treatment of waste with technologies such as gasification and pyrolysis, with energy recovery. The present study assessed the greenhouse gas emission impacts of three technologies that could be used for the treatment of Municipal Solid Waste in order to recover energy from it. These technologies are Mass Burn Incineration with energy recovery, Mechanical Biological Treatment via bio-drying and Mechanical Heat Treatment, which is a relatively new and uninvestigated method, compared to the other two. Mechanical Biological Treatment and Mechanical Heat Treatment can turn Municipal Solid Waste into Solid Recovered Fuel that could be combusted for energy production or replace other fuels in various industrial processes. The analysis showed that performance of these two technologies depends strongly on the final use of the produced fuel and they could produce GHG emissions savings only when there is end market for the fuel. On the other hand Mass Burn Incineration generates greenhouse gas emission savings when it recovers electricity and heat. Moreover the study found that the expected increase on the amount of Municipal Solid Waste treated for energy recovery in England by 2020 could save greenhouse gas emission, if certain Energy from Waste technologies would be applied, under certain conditions.

Final Technical Report: Commercial Advanced Lighting Control (ALC) Demonstration and Deployment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Arnold, Gabe

This three-year demonstration and deployment project sought to address market barriers to accelerating the adoption of Advanced Lighting Controls (ALCs), an underutilized technology with low market penetration. ALCs are defined as networked, addressable lighting control systems that utilize software or intelligent controllers to combine multiple energy-saving lighting control strategies in a single space (e.g., smart-time scheduling, daylight harvesting, task tuning, occupancy control, personal control, variable load-shedding, and plug-load control). The networked intelligent aspect of these systems allows applicable lighting control strategies to be combined in a single space, layered over one another, maximizing overall energy-savings. The project included five realmore » building demonstrations of ALCs across the Northeast US region. The demonstrations provided valuable data and experience to support deployment tasks that are necessary to overcome market barriers. These deployment tasks included development of training resources for building designers, installers, and trades, as well as development of new energy efficiency rebates for the technology from Efficiency Forward’s utility partners. Educating designers, installers, and trades on ALCs is a critical task for reducing the cost of the technology that is currently inflated due to perceived complexity and unfamiliarity with how to design and install the systems. Further, utility and non-utility energy efficiency programs continue to relegate the technology to custom or ill-suited prescriptive program designs that do not effectively deploy the technology at scale. This project developed new, scalable rebate approaches for the technology. Efficiency Forward utilized their DesignLights Consortium® (DLC) brand and network of 81 DLC member utilities to develop and deploy the results of the project. The outputs of the project have included five published case studies, a six-hour ALC technology training curriculum that has already been deployed in five US states, and new rebates offered for the technology that have been deployed by a dozen utilities across the US. Widespread adoption of ALC technology in commercial buildings would provide tremendous benefits. The current market penetration of ALC systems is estimated at <0.1% in commercial buildings. If ALC systems were installed in all commercial buildings, approximately 1,051 TBtu of energy could be saved. This would translate into customer cost savings of approximately $10.7 billion annually.« less

Saving Energy and Money: A Lesson in Computer Power Management

ERIC Educational Resources Information Center

Lazaros, Edward J.; Hua, David

2012-01-01

In this activity, students will develop an understanding of the economic impact of technology by estimating the cost savings of power management strategies in the classroom. Students will learn how to adjust computer display settings to influence the impact that the computer has on the financial burden to the school. They will use mathematics to…

Naval Science and Technology Future Force Magazine

Science.gov Websites

Issues Contact Us Links RSS Feed Facebook IT'S EASY TO SEE THE COST SAVINGS OF VIRTUAL REALITY TRAINING THE [...] Not Just a Fad: Virtual Reality Really Does Benefit the Military IT'S EASY TO SEE THE COST SAVINGS OF VIRTUAL REALITY TRAINING-BUT IS IT AS EFFECTIVE AS, OR EVEN BETTER THAN, OTHER TYPES OF

Alternative Fuels Data Center: Municipality with a Mission: Georgia Fleet

Science.gov Websites

different alternative fuels, based on mission needs, with the goal of saving money, reducing its combined. The vehicles have logged more than 90,000 problem-free miles and are projected to save the options before investing any time and money in new fuels and technologies. He directed Curtis to the

OpenADR Specification to Ease Saving Power in Buildings

ScienceCinema

Piette, Mary Ann

2017-12-09

A new data model developed by researchers at the Department of Energys Lawrence Berkeley National Laboratory and their colleagues at other universities and in the private sector will help facilities and buildings save power through automated demand response technology, and advance the development of the Smart Grid. http://newscenter.lbl.gov/press-releases/2009/04/27/openadr-specification/

Optimising boiler performance.

PubMed

Mayoh, Paul

2009-01-01

Soaring fuel costs continue to put the squeeze on already tight health service budgets. Yet it is estimated that combining established good practice with improved technologies could save between 10% and 30% of fuel costs for boilers. Paul Mayoh, UK technical manager at Spirax Sarco, examines some of the practical measures that healthcare organisations can take to gain their share of these potential savings.

General process improvements through pinch technology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Linnhoff, B.; Polley, G.T.; Sahdev, V.

1988-06-01

Over the last ten years pinch technology has emerged as somewhat of a ''maverick'' development in the process design and energy conservation scene. Running contrary to general trends by taking the computer out of the loop and putting the engineer back in control, it has been questioned by some and welcomed by others. Regardless of persuasion, however, critics and advocates alike have largely failed to notice that pinch technology is more than an energy conservation tool. This is probably because soon after the advent of pinch technology in the 1970s, the process design scene became dominated by the oil crisis.more » Energy savings became the primary task of process designers and, therefore, the primary focus of the technology. Application during this period typically demonstrated energy cost savings in the range of 20 to 50 percent and payback periods of one year or less. Only recently have the other benefits of the technology reemerged. While it is true that pinch technology is essentially a heat-flow-based technique it is also true that it can be used to address a very diverse range of objectives.« less

Advanced Sensors and Controls for Building Applications: Market Assessment and Potential R&D Pathways

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brambley, Michael R.; Haves, Philip; McDonald, Sean C.

2005-04-13

Significant energy savings can be achieved in commercial building operation, along with increased comfort and control for occupants, through the implementation of advanced technologies. This document provides a market assessment of existing building sensors and controls and presents a range of technology pathways (R&D options) for pursuing advanced sensors and building control strategies. This paper is actually a synthesis of five other white papers: the first describes the market assessment including estimates of market potential and energy savings for sensors and control strategies currently on the market as well as a discussion of market barriers to these technologies. The othermore » four cover technology pathways: (1) current applications and strategies for new applications, (2) sensors and controls, (3) networking, security, and protocols and standards, and (4) automated diagnostics, performance monitoring, commissioning, optimal control and tools. Each technology pathway chapter gives an overview of the technology or application. This is followed by a discussion of needs and the current status of the technology. Finally, a series of research topics is proposed.« less

Research and Energy Efficiency: Selected Success Stories

DOE R&D Accomplishments Database

Garland, P. W.; Garland, R. W.

1997-06-26

Energy use and energy technology play critical roles in the U.S. economy and modern society. The Department of Energy (DOE) conducts civilian energy research and development (R&D) programs for the purpose of identifying promising technologies that promote energy security, energy efficiency, and renewable energy use. DOE-sponsored research ranges from basic investigation of phenomena all the way through development of applied technology in partnership with industry. DOE`s research programs are conducted in support of national strategic energy objectives, however austere financial times have dictated that R&D programs be measured in terms of cost vs. benefit. In some cases it is difficult to measure the return on investment for the basic "curiosity-driven" research, however many applied technology development programs have resulted in measurable commercial successes. The DOE has published summaries of their most successful applied technology energy R&D programs. In this paper, we will discuss five examples from the Building Technologies area of the DOE Energy Efficiency program. Each story will describe the technology, discuss the level of federal funding, and discuss the returns in terms of energy savings, cost savings, or national economic impacts.

Innovative manufacturing and materials for low cost lithium ion batteries

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carlson, Steven

2015-12-29

This project demonstrated entirely new manufacturing process options for lithium ion batteries with major potential for improved cost and performance. These new manufacturing approaches are based on the use of the new electrode-coated separators instead of the conventional electrode-coated metal current collector foils. The key enabler to making these electrode-coated separators is a new and unique all-ceramic separator with no conventional porous plastic separator present. A simple, low cost, and high speed manufacturing process of a single coating of a ceramic pigment and polymer binder onto a re-usable release film, followed by a subsequent delamination of the all-ceramic separator andmore » any layers coated over it, such as electrodes and metal current collectors, was utilized. A suitable all-ceramic separator was developed that demonstrated the following required features needed for making electrode-coated separators: (1) no pores greater than 100 nanometer (nm) in diameter to prevent any penetration of the electrode pigments into the separator; (2) no shrinkage of the separator when heated to the high oven heats needed for drying of the electrode layer; and (3) no significant compression of the separator layer by the high pressure calendering step needed to densify the electrodes by about 30%. In addition, this nanoporous all-ceramic separator can be very thin at 8 microns thick for increased energy density, while providing all of the performance features provided by the current ceramic-coated plastic separators used in vehicle batteries: improved safety, longer cycle life, and stability to operate at voltages up to 5.0 V in order to obtain even more energy density. The thin all-ceramic separator provides a cost savings of at least 50% for the separator component and by itself meets the overall goal of this project to reduce the cell inactive component cost by at least 20%. The all-ceramic separator also enables further cost savings by its excellent heat stability with no shrinkage at up to 220oC. This allows vacuum drying of the dry cell just before filling with the electrolyte and thereby can reduce the size of the cell assembly dry room by 50%. Once the electrode-coated separator is produced, there are many different approaches for adding the metal current collector layers and making and connecting the tabs of the cells. These approaches include: (1) laminating the electrode side of the electrode-coated separator to both sides of a metal current collector; and (2) making a full coated electrode stack by coating or depositing a current collector layer on the electrode side and then coating a second electrode layer onto the current collector. Further cost savings are available from using lower cost and/or thinner and lighter current collectors and from using a separator coating manufacturing process at widths of 1.5 meters (m) or more and at high production line speeds of up to 125 meters per minute (mpm), both of which are well above the conventional coating widths and line speeds presently used in manufacturing electrodes for lithium ion batteries.« less

Modern energy efficient technologies of high-rise construction

NASA Astrophysics Data System (ADS)

Lukmanova, Inessa; Golov, Roman

2018-03-01

The paper analyzes modern energy-efficient technologies, both being applied, and only introduced into the application in the construction of high-rise residential buildings. All technologies are systematized by the authors as part of a unified model of "Arrows of Energy-Efficient Technologies", which imply performing energy-saving measures in the design, construction and operation of buildings.

Industrial application of green chromatography - II. Separation and analysis of preservatives in skincare products using subcritical water chromatography.

PubMed

Yang, Y; Kapalavavi, B; Gujjar, L; Hadrous, S; Marple, R; Gamsky, C

2012-10-01

Several high-temperature liquid chromatography (HTLC) and subcritical water chromatography (SBWC) methods have been successfully developed in this study for separation and analysis of preservatives contained in Olay skincare creams. Efficient separation and quantitative analysis of preservatives have been achieved on four commercially available ZirChrom and Waters XBridge columns at temperatures ranging from 100 to 200°C. The quantification results obtained by both HTLC and SBWC methods developed for preservatives analysis are accurate and reproducible. A large number of replicate HTLC and SBWC runs also indicate no significant system building-up or interference for skincare cream analysis. Compared with traditional HPLC separation carried out at ambient temperature, the HTLC methods can save up to 90% methanol required in the HPLC mobile phase. However, the SBWC methods developed in this project completely eliminated the use of toxic organic solvents required in the HPLC mobile phase, thus saving a significant amount of money and making the environment greener. Although both homemade and commercial systems can accomplish SBWC separations, the SBWC methods using the commercial system for preservative analysis are recommended for industrial applications because they can be directly applied in industrial plant settings. © 2012 The Authors ICS © 2012 Society of Cosmetic Scientists and the Société Française de Cosmétologie.

Net-Zero Building Technologies Create Substantial Energy Savings -

Science.gov Websites

-by-step information for decision making around net-zero energy building technologies. The past three improved insulation, windows, and heating and cooling systems. Despite these strides, energy use by energy building methodologies and technologies during a tour of the RSF's rooftop PV system. Photo by

Saving a Language with Computers, Tape Recorders, and Radio.

ERIC Educational Resources Information Center

Bennett, Ruth

This paper discusses the use of technology in instruction. It begins by examining research on technology and indigenous languages, focusing on the use of technology to get community attention for an indigenous language, improve the quantity of quality language, document spoken language, create sociocultural learning contexts, improve study skills,…

How can radio frequency identification technology impact nursing practice?

PubMed

Billingsley, Luanne; Wyld, David

2014-12-01

Radio frequency identification (RFID) technology can save nurses time, improve quality of care, en hance patient and staff safety, and decrease costs. However, without a better understanding of these systems and their benefits to patients and hospitals, nurses may be slower to recommend, implement, or adopt RFID technology into practice.

Next-generation purex flowsheets with acetohydroxamic acid as complexant for FBR and thermal-fuel reprocessing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kumar, Shekhar; Koganti, S.B.

2008-07-01

Acetohydroxamic acid (AHA) is a novel complexant for recycle of nuclear-fuel materials. It can be used in ordinary centrifugal extractors, eliminating the need for electro-redox equipment or complex maintenance requirements in a remotely maintained hot cell. In this work, the effect of AHA on Pu(IV) distribution ratios in 30% TBP system was quantified, modeled, and integrated in SIMPSEX code. Two sets of batch experiments involving macro Pu concentrations (conducted at IGCAR) and one high-Pu flowsheet (literature) were simulated for AHA based U-Pu separation. Based on the simulation and validation results, AHA based next-generation reprocessing flowsheets are proposed for co-processing basedmore » FBR and thermal-fuel reprocessing as well as evaporator-less macro-level Pu concentration process required for MOX fuel fabrication. Utilization of AHA results in significant simplification in plant design and simpler technology implementations with significant cost savings. (authors)« less

Modular Chemical Process Intensification: A Review.

PubMed

Kim, Yong-Ha; Park, Lydia K; Yiacoumi, Sotira; Tsouris, Costas

2017-06-07

Modular chemical process intensification can dramatically improve energy and process efficiencies of chemical processes through enhanced mass and heat transfer, application of external force fields, enhanced driving forces, and combinations of different unit operations, such as reaction and separation, in single-process equipment. These dramatic improvements lead to several benefits such as compactness or small footprint, energy and cost savings, enhanced safety, less waste production, and higher product quality. Because of these benefits, process intensification can play a major role in industrial and manufacturing sectors, including chemical, pulp and paper, energy, critical materials, and water treatment, among others. This article provides an overview of process intensification, including definitions, principles, tools, and possible applications, with the objective to contribute to the future development and potential applications of modular chemical process intensification in industrial and manufacturing sectors. Drivers and barriers contributing to the advancement of process intensification technologies are discussed.

Modular Chemical Process Intensification: A Review

DOE PAGES

Kim, Yong-ha; Park, Lydia K.; Yiacoumi, Sotira; ...

2016-06-24

Modular chemical process intensification can dramatically improve energy and process efficiencies of chemical processes through enhanced mass and heat transfer, application of external force fields, enhanced driving forces, and combinations of different unit operations, such as reaction and separation, in single-process equipment. Dramatic improvements such as these lead to several benefits such as compactness or small footprint, energy and cost savings, enhanced safety, less waste production, and higher product quality. Because of these benefits, process intensification can play a major role in industrial and manufacturing sectors, including chemical, pulp and paper, energy, critical materials, and water treatment, among others. Thismore » article provides an overview of process intensification, including definitions, principles, tools, and possible applications, with the objective to contribute to the future development and potential applications of modular chemical process intensification in industrial and manufacturing sectors. Drivers and barriers contributing to the advancement of process intensification technologies are discussed.« less

Smart Manufacturing Technologies and Data Analytics for Improving Energy Efficiency in Industrial Energy Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nimbalkar, Sachin U.; Guo, Wei; Wenning, Thomas J.

Smart manufacturing and advanced data analytics can help the manufacturing sector unlock energy efficiency from the equipment level to the entire manufacturing facility and the whole supply chain. These technologies can make manufacturing industries more competitive, with intelligent communication systems, real-time energy savings, and increased energy productivity. Smart manufacturing can give all employees in an organization the actionable information they need, when they need it, so that each person can contribute to the optimal operation of the corporation through informed, data-driven decision making. This paper examines smart technologies and data analytics approaches for improving energy efficiency and reducing energy costsmore » in process-supporting energy systems. It dives into energy-saving improvement opportunities through smart manufacturing technologies and sophisticated data collection and analysis. The energy systems covered in this paper include those with motors and drives, fans, pumps, air compressors, steam, and process heating.« less

Underground structure pattern and multi AO reaction with step feed concept for upgrading an large wastewater treatment plant

NASA Astrophysics Data System (ADS)

Peng, Yi; Zhang, Jie; Li, Dong

2018-03-01

A large wastewater treatment plant (WWTP) could not meet the new demand of urban environment and the need of reclaimed water in China, using a US treatment technology. Thus a multi AO reaction process (Anaerobic/oxic/anoxic/oxic/anoxic/oxic) WWTP with underground structure was proposed to carry out the upgrade project. Four main new technologies were applied: (1) multi AO reaction with step feed technology; (2) deodorization; (3) new energy-saving technology such as water resource heat pump and optical fiber lighting system; (4) dependable old WWTP’s water quality support measurement during new WWTP’s construction. After construction, upgrading WWTP had saved two thirds land occupation, increased 80% treatment capacity and improved effluent standard by more than two times. Moreover, it had become a benchmark of an ecological negative capital changing to a positive capital.

[Research on carbon reduction potential of electric vehicles for low-carbon transportation and its influencing factors].

PubMed

Shi, Xiao-Qing; Li, Xiao-Nuo; Yang, Jian-Xin

2013-01-01

Transportation is the key industry of urban energy consumption and carbon emissions. The transformation of conventional gasoline vehicles to new energy vehicles is an important initiative to realize the goal of developing low-carbon city through energy saving and emissions reduction, while electric vehicles (EV) will play an important role in this transition due to their advantage in energy saving and lower carbon emissions. After reviewing the existing researches on energy saving and emissions reduction of electric vehicles, this paper analyzed the factors affecting carbon emissions reduction. Combining with electric vehicles promotion program in Beijing, the paper analyzed carbon emissions and reduction potential of electric vehicles in six scenarios using the optimized energy consumption related carbon emissions model from the perspective of fuel life cycle. The scenarios included power energy structure, fuel type (energy consumption per 100 km), car type (CO2 emission factor of fuel), urban traffic conditions (speed), coal-power technologies and battery type (weight, energy efficiency). The results showed that the optimized model was able to estimate carbon emissions caused by fuel consumption more reasonably; electric vehicles had an obvious restrictive carbon reduction potential with the fluctuation of 57%-81.2% in the analysis of six influencing factors, while power energy structure and coal-power technologies play decisive roles in life-cycle carbon emissions of electric vehicles with the reduction potential of 78.1% and 81.2%, respectively. Finally, some optimized measures were proposed to reduce transport energy consumption and carbon emissions during electric vehicles promotion including improving energy structure and coal technology, popularizing energy saving technologies and electric vehicles, accelerating the battery R&D and so on. The research provides scientific basis and methods for the policy development for the transition of new energy vehicles in low-carbon transport.

Unintended consequence of managing the coupled humans and water: the irrigation efficiency paradox

NASA Astrophysics Data System (ADS)

Liu, Y.

2015-12-01

Water shortage most severely restricts the socio-economic development of many arid and semi-arid regions in the world, for which water-saving technology is believed to be an effective solution. However, as a realworld case, the total water consumption of Xinjiang Uygur Autonomous Region of China continued to increase as irrigation efficiency dramatically improved through the application of water-saving technology in the study period 1998-2010. This phenomenon, known as the irrigation efficiency paradox or Jevons paradox, is interpreted as an economic rebound effect. In this study, we explore the dynamic feedbacks between humans and water in this paradox through a socio-hydrological perspective. We analyze the co-evolutionary trajectory of coupled human-water dynamics from 1950 to 2010 to provide it a general context. A conceptual socio-hydrological model based on five key elements, namely, irrigation land, water-saving technology, water consumption, societal sensitivity to water scarcity, and the policy mix, is constructed. The policy mix to be adopted is determined by a social decision-making process mainly based on the societal sensitivity, which reflects the societal preference on two sorts of policies: (i) irrigation land control and (ii) water-saving technology promotion. Modeling results verify the hypothesized mechanism by successfully reproducing the observed dynamics including the emergence of the efficiency paradox. Our analysis indicates that the implementation of more adaptive rules may even eliminate the paradox. The effects of different initial policy mixes are also explored, and the results show that land control policies should be given equal priority when dealing with water scarcity. These findings point to a double-helix-type co-evolution of humans and water.

Integrating the Technology Acceptance Model and Diffusion of Innovation: Factors Promoting Interest in Energy Efficient and Renewable Energy Technologies at Military Installations, Federal Facilities and Land-Grant Universities

ERIC Educational Resources Information Center

Dudik, C. E. Jane

2017-01-01

Energy managers are tasked with identifying energy savings opportunities and promoting energy independence. Energy-efficient (EE) and renewable-energy (RE) technology demonstrations enable energy managers to evaluate new energy technologies and adopt those that appear most effective. This study examined whether energy technology demonstrations…

Economic Operation of Supercritical CO2 Refrigeration Energy Storage Technology

NASA Astrophysics Data System (ADS)

Hay, Ryan

With increasing penetration of intermittent renewable energy resources, improved methods of energy storage are becoming a crucial stepping stone in the path toward a smarter, greener grid. SuperCritical Technologies is a company based in Bremerton, WA that is developing a storage technology that can operate entirely on waste heat, a resource that is otherwise dispelled into the environment. The following research models this storage technology in several electricity spot markets around the US to determine if it is economically viable. A modification to the storage dispatch scheme is then presented which allows the storage unit to increase its profit in real-time markets by taking advantage of extreme price fluctuations. Next, the technology is modeled in combination with an industrial load profile on two different utility rate schedules to determine potential cost savings. The forecast of facility load has a significant impact on savings from the storage dispatch, so an exploration into this relationship is then presented.

Performance and economic evaluation of the seahorse natural gas hot water heater conversion at Fort Stewart. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Winiarski, D.W.

1995-12-01

The Federal government is the largest single energy consumer in the United States with consumption of nearly 1.5 quads/year of energy (10{sup 15} quad = 1015 Btu) and cost valued at nearly $10 billion annually. The US Department of Energy`s (DOE) Federal Energy Management Program (FEMP) supports efforts to reduce energy use and associated expenses in the Federal sector. One such effort, the New Technology Demonstration Program (NTDP) seeks to evaluate new energy -- saving US technologies and secure their more timely adoption by the US government. Pacific Northwest Laboratory (PNL) is one of four DOE laboratories that participate inmore » the New Technologies Demonstration Program, providing technical expertise and equipment to evaluate new, energy-saving technologies being studied under that program. This report provides the results of a field evaluation that PNL conducted for DOE/FEMP with funding support from the US Department of Defense (DoD) Strategic Environmental Research and Development Program (SERDP) to examine the performance of 4 candidate energy-saving technology-a water heater conversion system to convert electrically powered water heaters to natural gas fuel. The unit was installed at a single residence at Fort Stewart, a US Army base in Georgia, and the performance was monitored under the NTDP. Participating in this effort under a Cooperative Research and Development Agreement (CRADA) were Gas Fired Products, developers of the technology; the Public Service Company of North Carolina; Atlanta Gas Light Company; the Army Corps of Engineers; Fort Stewart; and Pacific Northwest Laboratory.« less

Leveraging Intelligent Vehicle Technologies to Maximize Fuel Economy (Presentation)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gonder, J.

2011-11-01

Advancements in vehicle electronics, along with communication and sensing technologies, have led to a growing number of intelligent vehicle applications. Example systems include those for advanced driver information, route planning and prediction, driver assistance, and crash avoidance. The National Renewable Energy Laboratory is exploring ways to leverage intelligent vehicle systems to achieve fuel savings. This presentation discusses several potential applications, such as providing intelligent feedback to drivers on specific ways to improve their driving efficiency, and using information about upcoming driving to optimize electrified vehicle control strategies for maximum energy efficiency and battery life. The talk also covers the potentialmore » of Advanced Driver Assistance Systems (ADAS) and related technologies to deliver significant fuel savings in addition to providing safety and convenience benefits.« less

Separation of the principal HDL subclasses by iodixanol ultracentrifugation

PubMed Central

Harman, Nicola L.; Griffin, Bruce A.; Davies, Ian G.

2013-01-01

HDL subclasses detection, in cardiovascular risk, has been limited due to the time-consuming nature of current techniques. We have developed a time-saving and reliable separation of the principal HDL subclasses employing iodixanol density gradient ultracentrifugation (IxDGUC) combined with digital photography. HDL subclasses were separated in 2.5 h from prestained plasma on a three-step iodixanol gradient. HDL subclass profiles were generated by digital photography and gel scan software. Plasma samples (n = 46) were used to optimize the gradient for the resolution of HDL heterogeneity and to compare profiles generated by IxDGUC with gradient gel electrophoresis (GGE); further characterization from participants (n = 548) with a range of lipid profiles was also performed. HDL subclass profiles generated by IxDGUC were comparable to those separated by GGE as indicated by a significant association between areas under the curve for both HDL2 and HDL3 (HDL2, r = 0.896, P < 0.01; HDL3, r = 0.894, P < 0.01). The method was highly reproducible, with intra- and interassay coefficient of variation percentage < 5 for percentage area under the curve HDL2 and HDL3, and < 1% for peak Rf and peak density. The method provides time-saving and cost-effective detection and preparation of the principal HDL subclasses. PMID:23690506

On eco-efficient technologies to minimize industrial water consumption

NASA Astrophysics Data System (ADS)

Amiri, Mohammad C.; Mohammadifard, Hossein; Ghaffari, Ghasem

2016-07-01

Purpose - Water scarcity will further stress on available water systems and decrease the security of water in many areas. Therefore, innovative methods to minimize industrial water usage and waste production are of paramount importance in the process of extending fresh water resources and happen to be the main life support systems in many arid regions of the world. This paper demonstrates that there are good opportunities for many industries to save water and decrease waste water in softening process by substituting traditional with echo-friendly methods. The patented puffing method is an eco-efficient and viable technology for water saving and waste reduction in lime softening process. Design/methodology/approach - Lime softening process (LSP) is a very sensitive process to chemical reactions. In addition, optimal monitoring not only results in minimizing sludge that must be disposed of but also it reduces the operating costs of water conditioning. Weakness of the current (regular) control of LSP based on chemical analysis has been demonstrated experimentally and compared with the eco-efficient puffing method. Findings - This paper demonstrates that there is a good opportunity for many industries to save water and decrease waste water in softening process by substituting traditional method with puffing method, a patented eco-efficient technology. Originality/value - Details of the required innovative works to minimize industrial water usage and waste production are outlined in this paper. Employing the novel puffing method for monitoring of lime softening process results in saving a considerable amount of water while reducing chemical sludge.

Commercializing Government-sponsored Innovations: Twelve Successful Buildings Case Studies

DOE R&D Accomplishments Database

Brown, M. A.; Berry, L. G.; Goel, R. K.

1989-01-01

This report examines the commercialization and use of R and D results funded by DOE's Office of Buildings and Community Systems (OBCS), an office that is dedicated to improving the energy efficiency of the nation's buildings. Three goals guided the research described in this report: to improve understanding of the factors that hinder or facilitate the transfer of OBCS R and D results, to determine which technology transfer strategies are most effective and under what circumstances each is appropriate, and to document the market penetration and energy savings achieved by successfully-commercialized innovations that have received OBCS support. Twelve successfully-commercialized innovations are discussed here. The methodology employed involved a review of the literature, interviews with innovation program managers and industry personnel, and data collection from secondary sources. Six generic technology transfer strategies are also described. Of these, contracting R and D to industrial partners is found to be the most commonly used strategy in our case studies. The market penetration achieved to date by the innovations studied ranges from less than 1% to 100%. For the three innovations with the highest predicted levels of energy savings (i.e., the flame retention head oil burner, low-E windows, and solid-state ballasts), combined cumulative savings by the year 2000 are likely to approach 2 quads. To date the energy savings for these three innovations have been about 0.2 quads. Our case studies illustrate the important role federal agencies can play in commercializing new technologies.

Low Energy Technology. A Unit of Instruction in Agricultural Economics. Planning for Energy Savings.

ERIC Educational Resources Information Center

Utley, Michael; Scanlon, Dennis C.

This unit of instruction on farm management for energy savings was designed for use by agribusiness and natural resources teachers in Florida high schools and by agricultural extension agents as they work with adults and students. It is one of a series of 11 instructional units (see note) written to help teachers and agents to educate their…

NREL's Work for the U.S. Navy Illuminates Energy and Cost Savings | News

Science.gov Websites

load controls and whole-building energy efficiency retrofits as good investments for the Navy. " Program Director Steve Gorin said. Advanced power strips, a plug load control technology that cuts power and an office building with capacity for roughly 100 staff. While plug load savings depend on what can

JPRS Report, Science & Technology, China: Energy.

DTIC Science & Technology

1988-02-10

bedrock growth anticlines, buried hill fault blocks, rolling anticlines, compression anticlines, draped anticlines, volcanic diapers and others. The...development and utilization of solar , wind, geothermal and other energy resources, the energy conservation capacity and newly-added energy resources were...equivalent to 20 million tons of standard coal. The firewood-saving capacity in wood and coal-saving stoves, biogas pits and solar cookers alone was

Unified Communications for Space Inventory Management

NASA Technical Reports Server (NTRS)

Gifford, Kevin K.; Fink, Patrick W.; Barton, Richard; Ngo, Phong H.

2009-01-01

To help assure mission success for long-duration exploration activities, NASA is actively pursuing wireless technologies that promote situational awareness and autonomy. Wireless technologies are typically extensible, offer freedom from wire tethers, readily support redundancy, offer potential for decreased wire weight, and can represent dissimilar implementation for increased reliability. In addition, wireless technologies can enable additional situational awareness that otherwise would be infeasible. For example, addition of wired sensors, the need for which might not have been apparent at the outset of a program, night be extremely costly due in part to the necessary routing of cables through the vehicle. RFID, or radio frequency identification, is a wireless technology with the potential for significant savings and increased reliability and safety in space operations. Perhaps the most obvious savings relate to the application of inventory management. A fully automated inventory management system is highly desirable for long-term sustaining operations in space environments. This assertion is evidenced by inventory activities on the International Space Station, which represents the most extensive inventory tracking experience base in the history of space operations. In the short tern, handheld RFID readers offer substantial savings owing to reduced crew time for inventory audits. Over the long term, a combination of improved RFID technology and operational concepts modified to fully utilize the technology should result in space based inventory management that is highly reliable and requires very little crew time. In addition to inventory management, RFID is likely to find space applications in real-time location and tracking systems. These could vary from coarse-resolution RFID portals to the high resolution afforded by ultra-wideband (UWB) RFID. Longer range RFID technologies that leverage passive surface acoustic wave (SAW) devices are being investigated to track assets on a lunar or planetary surface.

Better Buildings Alliance 2013 Annual Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

2014-01-31

We are pleased to share with you a copy of the 2013 Annual Report. Inside, you’ll find significant program accomplishments, profiles on highlighted members, and plans for 2014. With your contributions, support, and leadership over the past 12 months, the program has reached significant milestones, including: Growing membership to over 200 members, to represent over 10 billion square feet of U.S. commercial building space and one-seventh of the market; Increasing participation in the 15 Solutions Teams by 75%; Developing 3 new high-efficiency technology specifications that if widely implemented, could save more than $5 billion in energy costs per year; Launchingmore » the Advanced RTU Campaign and Wireless Meter Challenge, and surpassing 100 million sq. ft. in the Lighting Energy Efficiency in Parking (LEEP) Campaign; Welcoming partners in new sectors, including K-12 schools and local governments; The program is a critical element of the Better Buildings Initiative, driving 20% energy savings in the building sector by 2020 through innovation, new technologies, and profiling leadership. Thank you for your ongoing participation, we are looking forward to working with you in the new year on your energy saving targets and advancing technical and market practices that promote energy savings at your organization.« less

Influence of process operating parameters on dryness level and energy saving during wastewater sludge electro-dewatering.

PubMed

Mahmoud, Akrama; Hoadley, Andrew F A; Conrardy, Jean-Baptiste; Olivier, Jérémy; Vaxelaire, Jean

2016-10-15

Electrically assisted mechanical dewatering, known as electro-dewatering (EDW), is an alternative emerging technology for energy-efficient liquid/solids separation in the dewatering of wastewater sludge. In this study, the performance of the electro-dewatering (EDW) process for activated wastewater sludge was investigated. The influence of the operating modes; being the timing of voltage (U-EDW) or current (I-EDW) application to either or both the filtration and compression stages, and the influence of the applied pressure (in successive 30 min pressure steps) were studied. The results showed that by delaying the application of the electric field to the filter cake compression stage, there was a potential saving in power consumption of around 10-12% in the case of U-EDW and about 30-46% in the case of I-EDW. The increase of the applied pressure from 0.5 to 12 bar during the filter cake compression stage leads to an increase in electro-dewatering kinetics. The results also reveal that at a low electric field level the increase of the processing pressure has a relatively pronounced effect on the dewatering process. At high levels of the electric field, a minimum processing pressure (4-6 bar) is required to improve the electrical contact between the electrode and the sludge and thus lower the energy consumption. Copyright © 2016 Elsevier Ltd. All rights reserved.

Research and technology in the Federal Motor Carrier Safety Administration

DOT National Transportation Integrated Search

2002-01-01

As the Federal Government's chief commercial vehicle safety agency, the Federal Motor Carrier Safety Administration's (FMCSA), Office of Research and Technology (R&T) focuses on saving lives and reducing injuries by helping to prevent crashes involvi...

Wireless Success Story - Industrial Technologies Program (ITP)

DOE Office of Scientific and Technical Information (OSTI.GOV)

none,

This success story presents the results of wireless research by Sensors & Automation, a sub-program of the U.S. Department of Energy (DOE) Industrial Technologies Program (ITP). The prioritized research resulted in success with realized energy and cost savings.

Precision aerial application for site-specific rice crop management

USDA-ARS?s Scientific Manuscript database

Precision agriculture includes different technologies that allow agricultural professional to use information management tools to optimize agriculture production. The new technologies allow aerial application applicators to improve application accuracy and efficiency, which saves time and money for...

CHP Energy and Emissions Savings Calculator

EPA Pesticide Factsheets

Download the CHP Emissions Calculator, a tool that calculates the difference between the anticipated carbon dioxide, methane, nitrous oxide, sulfur dioxide, and nitrogen oxide emissions from a CHP system to those of a separate heat and power system.

Field monitoring and evaluation of a residential gas-engine-driven heat pump: Volume 2, Heating season

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miller, J.D.

1995-11-01

The Federal Government is the largest single energy consumer in the United States; consumption approaches 1.5 quads/year of energy (1 quad = 10{sup 15} Btu) at a cost valued at nearly $10 billion annually. The US Department of Energy (DOE) Federal Energy Management Program (FEMP) supports efforts to reduce energy use and associated expenses in the Federal sector. One such effort, the New Technology Demonstration Program (NTDP), seeks to evaluate new energy-saving US technologies and secure their more timely adoption by the US Government. Pacific Northwest Laboratory (PNL) is one of four DOE national multiprogram laboratories that participate in themore » NTDP by providing technical expertise and equipment to evaluate new, energy-saving technologies being studied and evaluated under that program. This two-volume report describes a field evaluation that PNL conducted for DOE/FEMP and the US Department of Defense (DoD) Strategic Environmental Research and Development Program (SERDP) to examine the performance of a candidate energy-saving technology -- a gas-engine-driven heat pump. The unit was installed at a single residence at Fort Sam Houston, a US Army base in San Antonio, Texas, and the performance was monitored under the NTDP. Participating in this effort under a Cooperative Research and Development Agreement (CRADA) were York International, the heat pump manufacturer; Gas Research Institute (GRI), the technology developer; City Public Service of San Antonio, the local utility; American Gas Cooling Center (AGCC); Fort Sam Houston; and PNL.« less

Energy Savings by Treating Buildings as Systems

NASA Astrophysics Data System (ADS)

Harvey, L. D. Danny

2008-09-01

This paper reviews the opportunities for dramatically reducing energy use in buildings by treating buildings as systems, rather than focusing on device efficiencies. Systems-level considerations are relevant for the operation of heat pumps (where the temperatures at which heat or coldness are distributed are particularly important); the joint or separate provision of heating, cooling, and ventilation; the joint or separate removal of sensible heat and moisture; and in the operation of fluid systems having pumps. Passive heating, cooling, and ventilation, as well as daylighting (use of sunlight for lighting purposes) also require consideration of buildings as systems. In order to achieve the significant (50-75%) energy savings that are possible through a systems approach, the design process itself has to involve a high degree of integration between the architect and various engineering disciplines (structural, mechanical, electrical), and requires the systematic examination and adjustment of alternative designs using computer simulation models.

Are Green Vehicles Worth the Extra Cost? The Case of Diesel-Electric Hybrid Technology for Urban Delivery Vehicles

ERIC Educational Resources Information Center

Krutilla, Kerry; Graham, John D.

2012-01-01

A central question for environmental policy is whether the long-term benefits of energy-saving technologies are sufficient to justify their short-term costs, and if so, whether financial incentives are needed to stimulate adoption. The fiscal effects of incentivizing new technologies, and the revenue effects of using the technology, are also…

Sand Filter Technology

DTIC Science & Technology

2016-08-01

Approved for public release: distribution unlimited TDS-NAVFAC-EXWC-PW-1604 Aug 2016 Sand Filter Technology This report summarizes the...findings from a demonstration of sand filter technology to determine whether the technology will save energy with a simple payback within the...EXWC) performed the evaluation at the Naval Air Station Lemoore, CA. The two year evaluation period began with one year of sand filter operation

Europe Report, Science and Technology.

DTIC Science & Technology

1986-11-17

fallout, bio- technology, stimulation, BRITE [Basic Research in Industrial Technologies for Europe] and non-nuclear energy ); -Overall assessment of...must make more use of new technologies," Narjes says. The new program will also pay particular attention to public health, environment, and energy ...nuclear fission and fusion). Concurrently subjects such as security, waste, and energy saving will get more attention. It is evident that the

Application of superalloy powder metallurgy for aircraft engines

NASA Technical Reports Server (NTRS)

Dreshfield, R. L.; Miner, R. V., Jr.

1980-01-01

In the last decade, Government/Industry programs have advanced powder metallurgy-near-net-shape technology to permit the use of hot isostatic pressed (HIP) turbine disks in the commercial aircraft fleet. These disks offer a 30% savings of input weight and an 8% savings in cost compared in cast-and-wrought disks. Similar savings were demonstrated for other rotating engine components. A compressor rotor fabricated from hot-die-forged-HIP superalloy billets revealed input weight savings of 54% and cost savings of 35% compared to cast-and-wrought parts. Engine components can be produced from compositions such as Rene 95 and Astroloy by conventional casting and forging, by forging of HIP powder billets, or by direct consolidation of powder by HIP. However, each process produces differences in microstructure or introduces different defects in the parts. As a result, their mechanical properties are not necessarily identical. Acceptance methods should be developed which recognize and account for the differences.

Energy implications of mechanical and mechanical–biological treatment compared to direct waste-to-energy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cimpan, Ciprian, E-mail: cic@kbm.sdu.dk; Wenzel, Henrik

2013-07-15

Highlights: • Compared systems achieve primary energy savings between 34 and 140 MJ{sub primary}/100 MJ{sub input} {sub waste.} • Savings magnitude is foremost determined by chosen primary energy and materials production. • Energy consumption and process losses can be upset by increased technology efficiency. • Material recovery accounts for significant shares of primary energy savings. • Direct waste-to-energy is highly efficient if cogeneration (CHP) is possible. - Abstract: Primary energy savings potential is used to compare five residual municipal solid waste treatment systems, including configurations with mechanical (MT) and mechanical–biological (MBT) pre-treatment, which produce waste-derived fuels (RDF and SRF), biogasmore » and/or recover additional materials for recycling, alongside a system based on conventional mass burn waste-to-energy and ash treatment. To examine the magnitude of potential savings we consider two energy efficiency levels (state-of-the-art and best available technology), the inclusion/exclusion of heat recovery (CHP vs. PP) and three different background end-use energy production systems (coal condensing electricity and natural gas heat, Nordic electricity mix and natural gas heat, and coal CHP energy quality allocation). The systems achieved net primary energy savings in a range between 34 and 140 MJ{sub primary}/100 MJ{sub input} {sub waste}, in the different scenario settings. The energy footprint of transportation needs, pre-treatment and reprocessing of recyclable materials was 3–9.5%, 1–18% and 1–8% respectively, relative to total energy savings. Mass combustion WtE achieved the highest savings in scenarios with CHP production, nonetheless, MBT-based systems had similarly high performance if SRF streams were co-combusted with coal. When RDF and SRF was only used in dedicated WtE plants, MBT-based systems totalled lower savings due to inherent system losses and additional energy costs. In scenarios without heat recovery, the biodrying MBS-based system achieved the highest savings, on the condition of SRF co-combustion. As a sensitivity scenario, alternative utilisation of SRF in cement kilns was modelled. It supported similar or higher net savings for all pre-treatment systems compared to mass combustion WtE, except when WtE CHP was possible in the first two background energy scenarios. Recovery of plastics for recycling before energy recovery increased net energy savings in most scenario variations, over those of full stream combustion. Sensitivity to assumptions regarding virgin plastic substitution was tested and was found to mostly favour plastic recovery.« less

Multi-interface Level Sensors and New Development in Monitoring and Control of Oil Separators

PubMed Central

Bukhari, Syed Faisal Ahmed; Yang, Wuqiang

2006-01-01

In the oil industry, huge saving may be made if suitable multi-interface level measurement systems are employed for effectively monitoring crude oil separators and efficient control of their operation. A number of techniques, e.g. externally mounted displacers, differential pressure transmitters and capacitance rod devices, have been developed to measure the separation process with gas, oil, water and other components. Because of the unavailability of suitable multi-interface level measurement systems, oil separators are currently operated by the trial-and-error approach. In this paper some conventional techniques, which have been used for level measurement in industry, and new development are discussed.

The Effectiveness of Using Technology in English Language Classrooms in Government Primary Schools in Bangladesh

ERIC Educational Resources Information Center

Parvin, Ruxana Hossain; Salam, Shaikh Flint

2015-01-01

Across the globe, governments of different countries have recognized the importance and value of digital technologies in language learning. This article is based on the pilot project of Save the Children using information and communication technology (ICT) in education. Through this initiative, interactive multimedia software based on national…

Composite Material Application to Liquid Rocket Engines

NASA Technical Reports Server (NTRS)

Judd, D. C.

1982-01-01

The substitution of reinforced plastic composite (RPC) materials for metal was studied. The major objectives were to: (1) determine the extent to which composite materials can be beneficially used in liquid rocket engines; (2) identify additional technology requirements; and (3) determine those areas which have the greatest potential for return. Weight savings, fabrication costs, performance, life, and maintainability factors were considered. Two baseline designs, representative of Earth to orbit and orbit to orbit engine systems, were selected. Weight savings are found to be possible for selected components with the substitution of materials for metal. Various technology needs are identified before RPC material can be used in rocket engine applications.

Innovative technology conserves resources and generates savings: a case study from the Sunnybrook Regional Processing Centre.

PubMed

Karim, Abdool Z

2009-01-01

The regional processing centre at Sunnybrook Health Sciences Centre recently faced the substantial challenge of increasing cleaning capacity to meet the current workload and anticipated future demand without increasing its operating budget. The solution, upgrading its cleaning and decontamination system to a highly automated system, met both objectives. An analysis of the impact of the change found that the new system provided additional benefits, including improved productivity and cleaning quality; decreased costs; reduced water, electricity and chemical use; improved worker safety and morale; and decreased overtime. Investing in innovative technology improved key departmental outcomes while meeting institutional environmental and cost savings objectives.

The research of automatic speed control algorithm based on Green CBTC

NASA Astrophysics Data System (ADS)

Lin, Ying; Xiong, Hui; Wang, Xiaoliang; Wu, Youyou; Zhang, Chuanqi

2017-06-01

Automatic speed control algorithm is one of the core technologies of train operation control system. It’s a typical multi-objective optimization control algorithm, which achieve the train speed control for timing, comfort, energy-saving and precise parking. At present, the train speed automatic control technology is widely used in metro and inter-city railways. It has been found that the automatic speed control technology can effectively reduce the driver’s intensity, and improve the operation quality. However, the current used algorithm is poor at energy-saving, even not as good as manual driving. In order to solve the problem of energy-saving, this paper proposes an automatic speed control algorithm based on Green CBTC system. Based on the Green CBTC system, the algorithm can adjust the operation status of the train to improve the efficient using rate of regenerative braking feedback energy while ensuring the timing, comfort and precise parking targets. Due to the reason, the energy-using of Green CBTC system is lower than traditional CBTC system. The simulation results show that the algorithm based on Green CBTC system can effectively reduce the energy-using due to the improvement of the using rate of regenerative braking feedback energy.

Unmanned Aerial Systems in Occupational Hygiene-Learning from Allied Disciplines.

PubMed

Eninger, Robert M; Johnson, Robert L

2015-10-01

Unmanned Aerial System (UAS) technologies are rapidly developing, lowering cost, and technology barriers for their use in numerous applications. This review and commentary summarizes relevant literature in allied fields and evaluates potential application and utility of UAS technology in the discipline of occupational hygiene. Disciplines closely related to occupational hygiene are moving to investigate potential uses--and in some cases--already employing this technology for research or commercial purposes. The literature was reviewed to formulate a cross-sectional picture of how UAS technology is being used in these closely allied disciplines which could inform or guide potential use in occupational hygiene. Discussed are UAS applications in environmental monitoring, emergency response, epidemiology, safety, and process optimization. A rapidly developing state of the art indicates that there is potential utility for this technology in occupational hygiene. Benefits may include cost savings, time savings, and averting hazardous environments via remote sensing. The occupational hygiene community can look to allied fields to garner lessons and possible applications to their own practice. Published by Oxford University Press on behalf of the British Occupational Hygiene Society 2015.

Technology selection for MSW treatment in Altiplano areas using FMDM.

PubMed

Jiang, Jianguo; Lou, Zhiying; Hg, Siio; Duo, Ji; Li, Zhong

2009-10-01

There are special requirements for municipal solid waste (MSW) treatment caused by lower oxygen content and atmospheric pressure on the Altiplano. The intention of this paper was to analyse the applicability of various technologies to MSW treatment in the Altiplano and select the best one based on the current MSW collection modes and technical levels, using the Fuzzy Mathematical Decision Method (FMDM). Technologies including landfill, incineration, composting, and anaerobic digestion (AD) were compared. The results of the studies showed that AD technology is a new technology which is attractive in economic terms and helpful for environmental harmony. AD can solve the difficulties caused by a high content of organic matter in the MSW, lower atmospheric pressure and oxygen content on the Altiplano. Moreover, it can achieve reduction and recycling of the waste, thereby saving space for treatment and disposal. Using this technology, renewable energy can be recovered to save conventional fuel consumption and the emission of greenhouse gases can be reduced to improve the conservation of the local ecosystem. Putting AD into practice in the Altiplano may be the preferred method of MSW treatment.

Waste water biological purification plants of dairy products industry and energy management

NASA Astrophysics Data System (ADS)

Stepanov, Sergey; Solkina, Olga; Stepanov, Alexander; Zhukova, Maria

2017-10-01

The paper presents results of engineering and economical comparison of waste water biological purification plants of dairy products industry. Three methods of purification are compared: traditional biological purification with the use of secondary clarifiers and afterpurification through granular-bed filters, biomembrane technology and physical-and-chemical treatment together with biomembrane technology for new construction conditions. The improvement of the biological purification technology using nitro-denitrification and membrane un-mixing of sludge mixture is a promising trend in this area. In these calculations, an energy management which is widely applied abroad was used. The descriptions of the three methods are illustrated with structural schemes. Costs of equipment and production areas are taken from manufacturers’ data. The research is aimed at an engineering and economical comparison of new constructions of waste water purification of dairy products industry. The experiment demonstrates advantages of biomembrane technology in waste water purification. This technology offers prospects of 122 million rubles cost saving during 25 years of operation when compared with of the technology of preparatory reagent flotation and of 13.7 million rubles cost saving compared to the option of traditional biological purification.

Automated procedures for sizing aerospace vehicle structures /SAVES/

NASA Technical Reports Server (NTRS)

Giles, G. L.; Blackburn, C. L.; Dixon, S. C.

1972-01-01

Results from a continuing effort to develop automated methods for structural design are described. A system of computer programs presently under development called SAVES is intended to automate the preliminary structural design of a complete aerospace vehicle. Each step in the automated design process of the SAVES system of programs is discussed, with emphasis placed on use of automated routines for generation of finite-element models. The versatility of these routines is demonstrated by structural models generated for a space shuttle orbiter, an advanced technology transport,n hydrogen fueled Mach 3 transport. Illustrative numerical results are presented for the Mach 3 transport wing.

The cost savings of expanding Medicaid eligibility to include currently uninsured homeless adults with substance use disorders.

PubMed

Zur, Julia; Mojtabai, Ramin; Li, Suhui

2014-04-01

Following the June 2012 Supreme Court ruling that states are no longer mandated to expand their Medicaid programs in 2014 as part of the Affordable Care Act, many states plan to opt out of the expansion, citing affordability as their primary concern. In response to this controversy, the present study evaluated the cost savings of expanding Medicaid coverage to include currently ineligible homeless adults with substance use disorders, a subset of the population that incurs some of the greatest societal costs and is disproportionately impacted by uninsurance. Using a time horizon of 7 years, separate analyses were conducted for state and federal governments, and then a final analysis evaluated the combined costs for the other two models. Results of the study demonstrate that, although the expansion will be associated with a net cost when combining state and federal expenses and savings, states will experience tremendous savings if they choose to participate.

Energy efficiency in the U.S. residential sector: An engineering and economic assessment of opportunities for large energy savings and greenhouse gas emissions reductions

NASA Astrophysics Data System (ADS)

Lima de Azevedo, Ines Margarida

Energy efficiency and conservation is a very promising part of a portfolio of the needed strategies to mitigate climate change. Several technologies and energy efficiency measures in the residential sector offer potential for large energy savings. However, while energy efficiency options are currently considered as a means of reducing carbon emissions, there is still large uncertainty about the effect of such measures on overall carbon savings. The first part of this thesis provides a national assessment of the energy efficiency potential in the residential sector under several different scenarios, which include the perspectives of different economic agents (consumers, utilities, ESCOs, and a society). The scenarios also include maximizing energy, electricity or carbon dioxide savings. The second part of this thesis deals with a detailed assessment of the potential for white-light LEDs for energy and carbon dioxide savings in the U.S. commercial and residential sectors. Solid-state lighting shows great promise as a source of efficient, affordable, color-balanced white light. Indeed, assuming market discount rates, the present work demonstrates that white solid-state lighting already has a lower levelized annual cost (LAC) than incandescent bulbs and that it will be lower than that of the most efficient fluorescent bulbs by the end of this decade. However, a large literature indicates that households do not make their decisions in terms of simple expected economic value. The present analysis shows that incorporating the findings from literature on high implicit discount rates from households when performing decisions towards efficient technologies delays the adoption of white LEDs by a couple of years. After a review of the technology, the present work compares the electricity consumption, carbon emissions and cost-effectiveness of current lighting technologies, when accounting for expected performance evolution through 2015. Simulations of lighting electricity consumption and implicit greenhouse gases emissions for the U.S. residential and commercial sectors through 2015 under different policy scenarios (voluntary solid-state lighting adoption, implementation of lighting standards in new construction and rebate programs or equivalent subsidies) are also included.

"More drop per crop" when moving from gravitational to drip irrigated agriculture? Experiences from a North Moroccan case study

NASA Astrophysics Data System (ADS)

Feltz, N.; Gaspart, F.; Vanclooster, M.

2015-12-01

In order to save agricultural water, the famous FAO's "more crop per drop" has been taken literally in many arid or semi-arid places around the world and policies that aim improving "efficiencies" (irrigation efficiency…) have been implemented, often leading to the promotion of water saving technologies. In 1865, studying coal consumption, W.S. Jevons highlighted that improving coal use efficiency could, as a paradox, lead to higher global coal use. Many economists later extended this idea to resource saving technologies in general, showing that, due to the "rebound effect", the adoption of more efficient technologies, in terms of use of resources, could lead to a higher global consumption of this resource if this adoption didn't go with adjustment measures. Regarding these considerations, the emerging question is to which extent water saving technologies (i.e. that aim improving water related efficiencies) are appropriate to save water at large scale. Our study addresses this question through the analysis of the conversion from surface to drip irrigation in Triffa's irrigated perimeter (Morocco). We aim addressing this question using the detailed analysis of two data sets. First, available data were collected for every farm within the study area from the local administrations. Second, interviews were conducted with farmers to complete the dataset and to characterize their behavior. This allowed assessing water related efficiencies at farm scale. Subsequently, models were implemented to link efficiencies with general attributes and thereby identify the main drivers of water related efficiencies in the study area. Finally, these models were used to upscale farm-scale assessment to the perimeter scale. Our results show that, under current conditions, moving from surface to drip irrigation leads to higher global water withdrawal. However, the aforementioned "rebound effect" does not allow explaining the higher pressure because of contextual specificities. Deeper analysis suggests that economic but also social and psychological issues need to be considered in this transition process. To fully achieve the expected results from moving to drip irrigation, those issues must be dealt with and the transition to drip irrigation must go hand in hand with stewardship programs and appropriate farmers capacity building.

48 CFR 23.200 - Scope.

Code of Federal Regulations, 2010 CFR

2010-10-01

... ENVIRONMENT, ENERGY AND WATER EFFICIENCY, RENEWABLE ENERGY TECHNOLOGIES, OCCUPATIONAL SAFETY, AND DRUG-FREE WORKPLACE Energy and Water Efficiency and Renewable Energy 23.200 Scope. (a) This subpart prescribes... that use renewable energy technology; and (2) Using an energy-savings performance contract to obtain...

48 CFR 23.200 - Scope.

Code of Federal Regulations, 2013 CFR

2013-10-01

... ENVIRONMENT, ENERGY AND WATER EFFICIENCY, RENEWABLE ENERGY TECHNOLOGIES, OCCUPATIONAL SAFETY, AND DRUG-FREE WORKPLACE Energy and Water Efficiency and Renewable Energy 23.200 Scope. (a) This subpart prescribes... that use renewable energy technology; and (2) Using an energy-savings performance contract to obtain...

48 CFR 23.200 - Scope.

Code of Federal Regulations, 2014 CFR

2014-10-01

... ENVIRONMENT, ENERGY AND WATER EFFICIENCY, RENEWABLE ENERGY TECHNOLOGIES, OCCUPATIONAL SAFETY, AND DRUG-FREE WORKPLACE Energy and Water Efficiency and Renewable Energy 23.200 Scope. (a) This subpart prescribes... that use renewable energy technology; and (2) Using an energy-savings performance contract to obtain...

48 CFR 23.200 - Scope.

Code of Federal Regulations, 2012 CFR

2012-10-01

... ENVIRONMENT, ENERGY AND WATER EFFICIENCY, RENEWABLE ENERGY TECHNOLOGIES, OCCUPATIONAL SAFETY, AND DRUG-FREE WORKPLACE Energy and Water Efficiency and Renewable Energy 23.200 Scope. (a) This subpart prescribes... that use renewable energy technology; and (2) Using an energy-savings performance contract to obtain...

48 CFR 23.200 - Scope.

Code of Federal Regulations, 2011 CFR

2011-10-01

... ENVIRONMENT, ENERGY AND WATER EFFICIENCY, RENEWABLE ENERGY TECHNOLOGIES, OCCUPATIONAL SAFETY, AND DRUG-FREE WORKPLACE Energy and Water Efficiency and Renewable Energy 23.200 Scope. (a) This subpart prescribes... that use renewable energy technology; and (2) Using an energy-savings performance contract to obtain...

Solid-State Lighting R&D Plan - 2015

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bardsley, Norman; Bland, Stephen; Hansen, Monica

2015-05-28

Provides analysis and direction for ongoing R&D activities to advance SSL technology and increase energy savings, reviewing SSL technology status and trends for both LEDs and OLEDs and offering an overview of the current DOE SSL R&D project portfolio.

Adding Audio Supported Smartboard Lectures to an Introductory Astronomy Online Laboratory

NASA Astrophysics Data System (ADS)

Lahaise, U. G. L.

2003-12-01

SMART Board(TM) and RealProducer(R) Plus technologies were used to develop a series of narrated pre-lab introductory online lectures. Smartboard slides were created by capturing images from internet pages and power point slides, then annotated and saved as web pages using smartboard technology. Short audio files were recorded using the RealProducer Plus software which were then linked to individual slides. WebCT was used to deliver the online laboratory. Students in an Introductory Astronomy of the Solar System Online laboratory used the lectures to prepare for laboratory exercises. The narrated pre-lab lectures were added to six out of eight suitable laboratory exercises. A survey was given to the students to research their online laboratory experience, in general, and the impact of the narrated smartboard lectures on their learning success, specifically. Data were collected for two accelerated sessions. Results show that students find the online laboratory equally hard or harder than a separate online lecture. The accelerated format created great time pressure which negatively affected their study habits. About half of the students used the narrated pre-lab lectures consistently. Preliminary findings show that lab scores in the accelerated sessions were brought up to the level of full semester courses.

Microwave Regenerable Air Purification Device

NASA Technical Reports Server (NTRS)

Atwater, James E.; Holtsnider, John T.; Wheeler, Richard R., Jr.

1996-01-01

The feasibility of using microwave power to thermally regenerate sorbents loaded with water vapor, CO2, and organic contaminants has been rigorously demonstrated. Sorbents challenged with air containing 0.5% CO2, 300 ppm acetone, 50 ppm trichloroethylene, and saturated with water vapor have been regenerated, singly and in combination. Microwave transmission, reflection, and phase shift has also been determined for a variety of sorbents over the frequency range between 1.3-2.7 GHz. This innovative technology offers the potential for significant energy savings in comparison to current resistive heating methods because energy is absorbed directly by the material to be heated. Conductive, convective and radiative losses are minimized. Extremely rapid heating is also possible, i.e., 1400 C in less than 60 seconds. Microwave powered thermal desorption is directly applicable to the needs of Advance Life Support in general, and of EVA in particular. Additionally, the applicability of two specific commercial applications arising from this technology have been demonstrated: the recovery for re-use of acetone (and similar solvents) from industrial waste streams using a carbon based molecular sieve; and the separation and destruction of trichloroethylene using ZSM-5 synthetic zeolite catalyst, a predominant halocarbon environmental contaminant. Based upon these results, Phase II development is strongly recommended.

Prompt and Precise Prototyping

NASA Technical Reports Server (NTRS)

2003-01-01

For Sanders Design International, Inc., of Wilton, New Hampshire, every passing second between the concept and realization of a product is essential to succeed in the rapid prototyping industry where amongst heavy competition, faster time-to-market means more business. To separate itself from its rivals, Sanders Design aligned with NASA's Marshall Space Flight Center to develop what it considers to be the most accurate rapid prototyping machine for fabrication of extremely precise tooling prototypes. The company's Rapid ToolMaker System has revolutionized production of high quality, small-to-medium sized prototype patterns and tooling molds with an exactness that surpasses that of computer numerically-controlled (CNC) machining devices. Created with funding and support from Marshall under a Small Business Innovation Research (SBIR) contract, the Rapid ToolMaker is a dual-use technology with applications in both commercial and military aerospace fields. The advanced technology provides cost savings in the design and manufacturing of automotive, electronic, and medical parts, as well as in other areas of consumer interest, such as jewelry and toys. For aerospace applications, the Rapid ToolMaker enables fabrication of high-quality turbine and compressor blades for jet engines on unmanned air vehicles, aircraft, and missiles.

Cooperation Helps Power Saving

DTIC Science & Technology

2009-04-07

the destination node hears the poll, the link between the two nodes is activated. In the original STEM, two radios working on two separate channels... hears the poll, the link between the two nodes is activated. In the original STEM, two radios working on two separate chan- nels are used: one radio is...Computer and Communications Societies. Proceedings. IEEE, vol. 3, pp. 1548–1557 vol.3, 2001. [2] R . Kravets and P. Krishnan, “Application-driven power

[Optimization theory and practical application of membrane science technology based on resource of traditional Chinese medicine residue].

PubMed

Zhu, Hua-Xu; Duan, Jin-Ao; Guo, Li-Wei; Li, Bo; Lu, Jin; Tang, Yu-Ping; Pan, Lin-Mei

2014-05-01

Resource of traditional Chinese medicine residue is an inevitable choice to form new industries characterized of modem, environmental protection and intensive in the Chinese medicine industry. Based on the analysis of source and the main chemical composition of the herb residue, and for the advantages of membrane science and technology used in the pharmaceutical industry, especially membrane separation technology used in improvement technical reserves of traditional extraction and separation process in the pharmaceutical industry, it is proposed that membrane science and technology is one of the most important choices in technological design of traditional Chinese medicine resource industrialization. Traditional Chinese medicine residue is a very complex material system in composition and character, and scientific and effective "separation" process is the key areas of technology to re-use it. Integrated process can improve the productivity of the target product, enhance the purity of the product in the separation process, and solve many tasks which conventional separation is difficult to achieve. As integrated separation technology has the advantages of simplified process and reduced consumption, which are in line with the trend of the modern pharmaceutical industry, the membrane separation technology can provide a broad platform for integrated process, and membrane separation technology with its integrated technology have broad application prospects in achieving resource and industrialization process of traditional Chinese medicine residue. We discuss the principles, methods and applications practice of effective component resources in herb residue using membrane separation and integrated technology, describe the extraction, separation, concentration and purification application of membrane technology in traditional Chinese medicine residue, and systematically discourse suitability and feasibility of membrane technology in the process of traditional Chinese medicine resource industrialization in this paper.

Weatherization Works II - Summary of Findings from the ARRA Period Evaluation of the U.S. Department of Energy's Weatherization Assistance Program

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tonn, Bruce Edward; Carroll, David; Rose, Erin M.

2015-10-01

This report presents a summary of the American Recovery and Reinvestment Act of 2009 (ARRA) evaluation of the U.S. Department of Energy s low-income Weatherization Program. This evaluation focused on the WAP Program Year 2010. The ARRA evaluation produced fourteen separate reports, including this summary. Three separate reports address the energy savings, energy cost savings, and cost effectiveness of WAP across four housing types: single family, mobile home, and large multifamily. Other reports address the environmental emissions benefits attributable to WAP, and characterize the program. Special studies were conducted to: estimate the impacts of weatherization and healthy homes interventions onmore » asthma-related Medicaid claims in a small cohort in Washington State; assess how weatherization recipients communicate their weatherization experiences to those in their social network, and assess processes implemented to defer homes for weatherization. Small studies addressed energy use in refrigerators, WAP as implemented in the U.S. territories for the first time, and weatherization s impacts on air conditioning energy savings. The national occupant survey was mined for additional insights on the impacts of weatherization on household budgets and energy behaviors post-weatherization. Lastly, the results of a survey of weatherization training centers are summarized.« less

Weatherization Works--Summary of Findings from the Retrospective Evaluation of the U.S. DOE's Weatherization Assistance Program

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tonn, Bruce Edward; Carroll, David; Pigg, Scott

This report presents a summary of the studies and analyses that compose the retrospective evaluation of the U.S. Department of Energy s low-income Weatherization Assistance Program (WAP). WAP provides grants to Grantees (i.e., states) that then provide grants to Subgrantees (i.e., local weatherization agencies) to weatherize low-income homes. This evaluation focused on the WAP Program Year 2008. The retrospective evaluation produced twenty separate reports, including this summary. Four separate reports address the energy savings, energy cost savings, and cost effectiveness of WAP across four housing types: single family, mobile home, small multifamily, and large multifamily. Other reports address the environmentalmore » emissions, macroeconomic, and health and household-related benefits attributable to WAP, and characterize the program, its recipients, and those eligible for the program. Major field studies are also summarized, including a major indoor air quality study and a follow-up ventilation study, an in-depth in-field assessment of weatherization work and quality, and a study that assesses reasons for variations in energy savings across homes. Results of surveys of weatherization staff, occupants, occupants satisfaction with weatherization services provided, and weatherization trainees are summarized. Lastly, this report summarizes a set of fifteen case studies of high-performing and unique local weatherization agencies.« less

The Energy - Water Connection: Can We Sustain Critical Resources and Make them Reliable, Affordable, and Environmentally Sound?(LBNL Summer Lecture Series)

ScienceCinema

McMahon, Jim

2018-05-16

Summer Lecture Series 2006: Jim McMahon of Berkeley Lab's Environmental Energy Technologies Division (EETD) is head of the Energy Analysis Department in EETD, which provides technical analysis to the Department of Energy on things like energy efficiency appliance standards. McMahon and his colleagues helped the nation save tens of billions of dollars in energy costs since the standards program began. Now his Water-Energy Technology Team (WETT) is applying its expertise to the linked problem of energy and water. Each of us requires more than 500 gallons per person per day for food production, plus an additional 465 gallons to produce household electricity. WETT hopes to mine some of the numerous opportunities to save energy and water by applying new technologies.

Defining the future of health technology: biomechatronics.

PubMed

Bushko, Renata G

2002-01-01

Future progress in healthcare and medicine depends on today's investment in research, development, and education. We cannot leave such urgent issues to determine themselves, but rather must actively collaborate to ensure a stable healthcare system. This chapter describes efforts made by leading experts in industry, government, and academia to better ascertain future healthcare management. Such collaboration has occurred during a series of Future Healthcare Technology Summits helping in planning investments in health technology. Deliberating and reviewing plans before taking action will accelerate progress as it will (1) save costs, (2) encourage compliance, (3) improve clinical outcomes, and (4) ensure greater patient satisfaction. What we must resolve is: How can we invest a couple billion dollars to save hundreds of billions and, most importantly, increase human health in the future. A new branch of science, Biomechatronics, with millions of Intelligent Caring Creatures- is the answer.

Examination of the costs, benefits and enery conservation aspects of the NASA aircraft fuel conservation technology program

NASA Technical Reports Server (NTRS)

1975-01-01

The costs and benefits of the NASA Aircraft Fuel Conservation Technology Program are discussed. Consideration is given to a present worth analysis of the planned program expenditures, an examination of the fuel savings to be obtained by the year 2005 and the worth of this fuel savings relative to the investment required, a comparison of the program funding with that planned by other Federal agencies for energy conservation, an examination of the private industry aeronautical research and technology financial posture for the period FY 76 - FY 85, and an assessment of the potential impacts on air and noise pollution. To aid in this analysis, a computerized fleet mix forecasting model was developed. This model enables the estimation of fuel consumption and present worth of fuel expenditures for selected commerical aircraft fleet mix scenarios.

Freight Wing Trailer Aerodynamics Final Technical Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sean Graham

2007-10-31

Freight Wing Incorporated utilized the opportunity presented by a DOE category two Inventions and Innovations grant to commercialize and improve upon aerodynamic technology for semi-tuck trailers, capable of decreasing heavy vehicle fuel consumption, related environmental damage, and U.S. consumption of foreign oil. Major project goals included the demonstration of aerodynamic trailer technology in trucking fleet operations, and the development and testing of second generation products. A great deal of past scientific research has demonstrated that streamlining box shaped semi-trailers can significantly reduce a truck’s fuel consumption. However, significant design challenges have prevented past concepts from meeting industry needs. Freight Wingmore » utilized a 2003 category one Inventions and Innovations grant to develop practical solutions to trailer aerodynamics. Fairings developed for the front, rear, and bottom of standard semi-trailers together demonstrated a 7% improvement to fuel economy in scientific tests conducted by the Transportation Research Center (TRC). Operational tests with major trucking fleets proved the functionality of the products, which were subsequently brought to market. This category two grant enabled Freight Wing to further develop, test and commercialize its products, resulting in greatly increased understanding and acceptance of aerodynamic trailer technology. Commercialization was stimulated by offering trucking fleets 50% cost sharing on trial implementations of Freight Wing products for testing and evaluation purposes. Over 230 fairings were implemented through the program with 35 trucking fleets including industry leaders such as Wal-Mart, Frito Lay and Whole Foods. The feedback from these testing partnerships was quite positive with product performance exceeding fleet expectations in many cases. Fleet feedback also was also valuable from a product development standpoint and assisted the design of several second generation products intended to further improve efficiency, lower costs, and enhance durability. Resulting products demonstrated a 30% efficiency improvement in full scale wind tunnel tests. The fuel savings of our most promising product, the “Belly Fairing” increased from 4% to 6% in scientific track and operational tests. The project successfully demonstrated the economic feasibility of trailer aerodynamics and positioned the technology to realize significant public benefits. Scientific testing conducted with partners such as the EPA Smartway program and Transport Canada clearly validated the fuel and emission saving potential of the technology. The Smartway program now recommends trailer aerodynamics as a certified fuel saving technology and is offering incentives such as low interest loans. Trailer aerodynamics can save average trucks over 1,100 gallons of fuel an 13 tons of emissions every 100,000 miles, a distance many trucks travel annually. These fuel savings produce a product return on investment period of one to two years in average fleet operations. The economic feasibility of the products was validated by participating fleets, several of which have since completed large implementations or demonstrated an interest in volume orders. The commercialization potential of the technology was also demonstrated, resulting in a national distribution and manufacturing partnership with a major industry supplier, Carrier Transicold. Consequently, Freight Wing is well positioned to continue marketing trailer aerodynamics to the trucking industry. The participation of leading fleets in this project served to break down the market skepticism that represents a primary barrier to widespread industry utilization. The benefits of widespread utilization of the technology could be quite significant for both the transportation industry and the public. Trailer aerodynamics could potentially save the U.S. trucking fleet over a billion gallons of fuel and 20 million tons of emissions annually.« less

Technology Demonstration: Acoustic Condition Assessment of Wastewater Collection Systems

EPA Science Inventory

The overall objective of this demonstration project was to evaluate technologies that are designed for rapid deployment using portable equipment that can result in significant cost-savings to wastewater utilities. Smaller diameter pipes (i.e., less than 12-inch diameter) are gen...

10 CFR 436.32 - Qualified contractors lists.

Code of Federal Regulations, 2014 CFR

2014-01-01

... implement the technologies which it proposes to provide; (2) Previous project clients provide ratings which... DEPARTMENT OF ENERGY ENERGY CONSERVATION FEDERAL ENERGY MANAGEMENT AND PLANNING PROGRAMS Methods and... cost savings performance services and grouped by technology. The list shall be prepared from statements...

10 CFR 436.32 - Qualified contractors lists.

Code of Federal Regulations, 2012 CFR

2012-01-01

... implement the technologies which it proposes to provide; (2) Previous project clients provide ratings which... DEPARTMENT OF ENERGY ENERGY CONSERVATION FEDERAL ENERGY MANAGEMENT AND PLANNING PROGRAMS Methods and... cost savings performance services and grouped by technology. The list shall be prepared from statements...

10 CFR 436.32 - Qualified contractors lists.

Code of Federal Regulations, 2011 CFR

2011-01-01

... implement the technologies which it proposes to provide; (2) Previous project clients provide ratings which... DEPARTMENT OF ENERGY ENERGY CONSERVATION FEDERAL ENERGY MANAGEMENT AND PLANNING PROGRAMS Methods and... cost savings performance services and grouped by technology. The list shall be prepared from statements...

10 CFR 436.32 - Qualified contractors lists.

Code of Federal Regulations, 2013 CFR

2013-01-01

... implement the technologies which it proposes to provide; (2) Previous project clients provide ratings which... DEPARTMENT OF ENERGY ENERGY CONSERVATION FEDERAL ENERGY MANAGEMENT AND PLANNING PROGRAMS Methods and... cost savings performance services and grouped by technology. The list shall be prepared from statements...

POLLUTION PREVENTION TECHNOLOGY DIFFUSION INITIATIVE (TDI)

EPA Science Inventory

Although pollution prevention (P2) technologies save money and help prevent the release of toxic and hazardous wastes into the environment, many companies are reluctant to install new equipment or change the current processes. Some of the reluctance is initiated by lack of time a...

DOE Office of Scientific and Technical Information (OSTI.GOV)

None, None

The SSL R&D Plan provides analysis and direction for ongoing R&D activities to advance SSL technology and increase energy savings. The R&D Plan also reviews SSL technology status and trends for both LEDs and OLEDs and offers an overview of the current DOE SSL R&D project portfolio.

THE SUPERFUND INNOVATIVE TECHNOLOGY EVALUATION PROGRAM; ANNUAL REPORT TO CONGRESS, FY 1998

EPA Science Inventory

This document summarizes the accomplishments and activities of the Superfund Innovative Technology Evaluation (SITE) Program for 1998. General information on the SITE program is presented. In addition, cost savings effected by the SITE program were estimated and are presented. ...

Technology Dollars from Pennies Saved.

ERIC Educational Resources Information Center

Anderson, Mary Alice

1996-01-01

Suggests ways to stretch media center budgets for technology, based on experiences at Winona Middle School (Minnesota). Topics include keeping statistics, hardware purchase and warranty information, centralizing purchases, planning for the reallocation of hardware and software, creative financing, working with business and community groups, staff…

Ferment in Technology

ERIC Educational Resources Information Center

Crossland, Janice

1974-01-01

A pollution-reducing and energy-saving alternative to petroleum use could be the fermentation industry and other technologies based on the use of renewable resources. Expansion of the fermentation industry could reduce our dependence on petroleum, reduce growing waste disposal problems, and help solve world food shortages. (BT)

Technology "Outsourcing": The Results Are Mixed.

ERIC Educational Resources Information Center

Blumenstyk, Goldie

1999-01-01

Reviews "outsourcing" of technology services by institutions of higher education, including the College of Notre Dame (California) and East Tennessee State University, and finds that, although external companies, especially COLLEGIS, offer expertise and savings, they sometimes do not understand the special problems of an academic…

Agreement Technologies for Energy Optimization at Home.

PubMed

González-Briones, Alfonso; Chamoso, Pablo; De La Prieta, Fernando; Demazeau, Yves; Corchado, Juan M

2018-05-19

Nowadays, it is becoming increasingly common to deploy sensors in public buildings or homes with the aim of obtaining data from the environment and taking decisions that help to save energy. Many of the current state-of-the-art systems make decisions considering solely the environmental factors that cause the consumption of energy. These systems are successful at optimizing energy consumption; however, they do not adapt to the preferences of users and their comfort. Any system that is to be used by end-users should consider factors that affect their wellbeing. Thus, this article proposes an energy-saving system, which apart from considering the environmental conditions also adapts to the preferences of inhabitants. The architecture is based on a Multi-Agent System (MAS), its agents use Agreement Technologies (AT) to perform a negotiation process between the comfort preferences of the users and the degree of optimization that the system can achieve according to these preferences. A case study was conducted in an office building, showing that the proposed system achieved average energy savings of 17.15%.

Solar thermal technology development: Estimated market size and energy cost savings. Volume 1: Executive summary

NASA Technical Reports Server (NTRS)

Gates, W. R.

1983-01-01

Estimated future energy cost savings associated with the development of cost-competitive solar thermal technologies (STT) are discussed. Analysis is restricted to STT in electric applications for 16 high-insolation/high-energy-price states. The fuel price scenarios and three 1990 STT system costs are considered, reflecting uncertainty over future fuel prices and STT cost projections. STT R&D is found to be unacceptably risky for private industry in the absence of federal support. Energy cost savings were projected to range from $0 to $10 billion (1990 values in 1981 dollars), dependng on the system cost and fuel price scenario. Normal R&D investment risks are accentuated because the Organization of Petroleum Exporting Countries (OPEC) cartel can artificially manipulate oil prices and undercut growth of alternative energy sources. Federal participation in STT R&D to help capture the potential benefits of developing cost-competitive STT was found to be in the national interest.

Solar thermal technology development: Estimated market size and energy cost savings. Volume 1: Executive summary

NASA Astrophysics Data System (ADS)

Gates, W. R.

1983-02-01

Estimated future energy cost savings associated with the development of cost-competitive solar thermal technologies (STT) are discussed. Analysis is restricted to STT in electric applications for 16 high-insolation/high-energy-price states. The fuel price scenarios and three 1990 STT system costs are considered, reflecting uncertainty over future fuel prices and STT cost projections. STT R&D is found to be unacceptably risky for private industry in the absence of federal support. Energy cost savings were projected to range from $0 to $10 billion (1990 values in 1981 dollars), dependng on the system cost and fuel price scenario. Normal R&D investment risks are accentuated because the Organization of Petroleum Exporting Countries (OPEC) cartel can artificially manipulate oil prices and undercut growth of alternative energy sources. Federal participation in STT R&D to help capture the potential benefits of developing cost-competitive STT was found to be in the national interest.

Fuel savings potential of the NASA Advanced Turboprop Program

DOE Office of Scientific and Technical Information (OSTI.GOV)

Whitlow, J.B. Jr.; Sievers, G.K.

1984-01-01

The NASA Advanced Turboprop (ATP) Program is directed at developing new technology for highly loaded, multibladed propellers for use at Mach 0.65 to 0.85 and at altitudes compatible with the air transport system requirements. Advanced turboprop engines offer the potential of 15 to 30 percent savings in aircraft block fuel relative to advanced turbofan engines (50 to 60 percent savings over today's turbofan fleet). The concept, propulsive efficiency gains, block fuel savings and other benefits, and the program objectives through a systems approach are described. Current program status and major accomplishments in both single rotation and counter rotation propeller technologymore » are addressed. The overall program from scale model wind tunnel tests to large scale flight tests on testbed aircraft is discussed.« less

Rescuing Writing Instruction: How To Save Time & Money with Technology

ERIC Educational Resources Information Center

Kuriloff, Peshe C.

2004-01-01

This document focuses on the writing skills of college students. The days of students sifting through piles of file cards, producing detailed outlines, and handwriting drafts have slipped into the distant past. Students write quickly and casually with the assistance of technology, and common sense dictates that technology needs to be used to teach…

The New Film Technologies: Computerized Video-Assisted Film Production.

ERIC Educational Resources Information Center

Mott, Donald R.

Over the past few years, video technology has been used to assist film directors after they have shot a scene, to control costs, and to create special effects, especially computer assisted graphics. At present, a computer based editing system called "Film 5" combines computer technology and video tape with film to save as much as 50% of…

Industrial Technologies Program - A Clean, Secure Energy Future via Industrial Energy Efficiency

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

The Industrial Technologies Program (ITP) leads the national effort to save energy and reduce greenhouse gas emissions in the largest energy-using sector of the U.S. economy. ITP drives energy efficiency improvements and carbon dioxide reductions throughout the manufacturing supply chain, helping develop and deploy innovative technologies that transform the way industry uses energy.

Does Technology Pay? Investing Wisely Takes Discipline

ERIC Educational Resources Information Center

Simkins, Michael

2006-01-01

Conservative estimates indicate that in the past five years U.S. schools have spent more than $25 billion on various forms of technology. With these figures in mind, it is important to ask how to increase the chances of getting value for technology investment. There is no magic formula for calculating a specific dollar estimate of savings or…

EPA ENERGY STAR: Tackling Growth in Home Electronics and Small Appliances

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sanchez, Marla Christine; Brown, Richard; Homan, Gregory

2008-11-17

Over a decade ago, the electricity consumption associated with home electronics and other small appliances emerged onto the global energy policy landscape as one of the fastest growing residential end uses with the opportunity to deliver significant energy savings. As our knowledge of this end use matures, it is essential to step back and evaluate the degree to which energy efficiency programs have successfully realized energy savings and where savings opportunities have been missed.For the past fifteen years, we have quantified energy, utility bill, and carbon savings for US EPA?s ENERGY STAR voluntary product labeling program. In this paper, wemore » present a unique look into the US residential program savings claimed to date for EPA?s ENERGY STAR office equipment, consumer electronics, and other small household appliances as well as EPA?s projected program savings over the next five years. We present a top-level discussion identifying program areas where EPA?s ENERGY STAR efforts have succeeded and program areas where ENERGY STAR efforts did not successfully address underlying market factors, technology issues and/or consumer behavior. We end by presenting the magnitude of ?overlooked? savings.« less

Airspace Technology Demonstration 3 (ATD-3): Dynamic Weather Routes (DWR) Technology Transfer Document Summary Version 1.0

NASA Technical Reports Server (NTRS)

Sheth, Kapil; Wang, Easter Mayan Chan

2016-01-01

Airspace Technology Demonstration #3 (ATD-3) is part of NASA's Airspace Operations and Safety Program (AOSP) - specifically, its Airspace Technology Demonstrations (ATD) Project. ATD-3 is a multiyear research and development effort which proposes to develop and demonstrate automation technologies and operating concepts that enable air navigation service providers and airspace users to continuously assess weather, winds, traffic, and other information to identify, evaluate, and implement workable opportunities for flight plan route corrections that can result in significant flight time and fuel savings in en route airspace. In order to ensure that the products of this tech-transfer are relevant and useful, NASA has created strong partnerships with the FAA and key industry stakeholders. This summary document and accompanying technology artifacts satisfy the first of three Research Transition Products (RTPs) defined in the Applied Traffic Flow Management (ATFM) Research Transition Team (RTT) Plan. This transfer consists of NASA's legacy Dynamic Weather Routes (DWR) work for efficient routing for en-route weather avoidance. DWR is a ground-based trajectory automation system that continuously and automatically analyzes active airborne aircraft in en route airspace to identify opportunities for simple corrections to flight plan routes that can save significant flying time, at least five minutes wind-corrected, while avoiding weather and considering traffic conflicts, airspace sector congestion, special use airspace, and FAA routing restrictions. The key benefit of the DWR concept is to let automation continuously and automatically analyze active flights to find those where simple route corrections can save significant time and fuel. Operators are busy during weather events. It is more effective to let automation find the opportunities for high-value route corrections.

Reducing environmental damage through the use of unmanned aerial vehicles as the best available technology

NASA Astrophysics Data System (ADS)

Fedulova, E. A.; Akulov, A. O.; Rada, A. O.; Alabina, T. A.; Savina, Ju Ju

2018-01-01

The article examines the possibilities of using unmanned aerial vehicles as the best available technologies in the field of agriculture and mining. The object of the study is the use of unmanned aerial vehicles as the best available technology. The main areas of application of this technology are identified: agro technical operations, aerial photography of mining operations. The technology of unmanned aerial vehicles is compared with the technologies of ground agricultural machinery. The research methodology includes an expert evaluation of the unmanned aerial vehicle technology belonging to the class of the best available technologies by the criteria: the level of environmental impact, resource saving, the use of low-waste, non-waste processes, the existence of at least two objects, economic efficiency. Expert evaluations were processed using the apparatus of fuzzy sets, which make it possible to construct membership functions. This allowed us to prove that the technology of unmanned aerial vehicles belongs to a fuzzy set of the best available technologies. The results of the research show that the use of unmanned aerial vehicles provides a saving of resources, especially non-renewable combustible minerals, reduces emissions and discharges of pollutants into the atmosphere, and also reduces soil erosion. Unmanned aerial vehicles should be included in the national directories of the best available technologies for the mining industry and agriculture.

Spinoff 2011

NASA Technical Reports Server (NTRS)

2012-01-01

Topics include: Bioreactors Drive Advances in Tissue Engineering; Tooling Techniques Enhance Medical Imaging; Ventilator Technologies Sustain Critically Injured Patients; Protein Innovations Advance Drug Treatments, Skin Care; Mass Analyzers Facilitate Research on Addiction; Frameworks Coordinate Scientific Data Management; Cameras Improve Navigation for Pilots, Drivers; Integrated Design Tools Reduce Risk, Cost; Advisory Systems Save Time, Fuel for Airlines; Modeling Programs Increase Aircraft Design Safety; Fly-by-Wire Systems Enable Safer, More Efficient Flight; Modified Fittings Enhance Industrial Safety; Simulation Tools Model Icing for Aircraft Design; Information Systems Coordinate Emergency Management; Imaging Systems Provide Maps for U.S. Soldiers; High-Pressure Systems Suppress Fires in Seconds; Alloy-Enhanced Fans Maintain Fresh Air in Tunnels; Control Algorithms Charge Batteries Faster; Software Programs Derive Measurements from Photographs; Retrofits Convert Gas Vehicles into Hybrids; NASA Missions Inspire Online Video Games; Monitors Track Vital Signs for Fitness and Safety; Thermal Components Boost Performance of HVAC Systems; World Wind Tools Reveal Environmental Change; Analyzers Measure Greenhouse Gasses, Airborne Pollutants; Remediation Technologies Eliminate Contaminants; Receivers Gather Data for Climate, Weather Prediction; Coating Processes Boost Performance of Solar Cells; Analyzers Provide Water Security in Space and on Earth; Catalyst Substrates Remove Contaminants, Produce Fuel; Rocket Engine Innovations Advance Clean Energy; Technologies Render Views of Earth for Virtual Navigation; Content Platforms Meet Data Storage, Retrieval Needs; Tools Ensure Reliability of Critical Software; Electronic Handbooks Simplify Process Management; Software Innovations Speed Scientific Computing; Controller Chips Preserve Microprocessor Function; Nanotube Production Devices Expand Research Capabilities; Custom Machines Advance Composite Manufacturing; Polyimide Foams Offer Superior Insulation; Beam Steering Devices Reduce Payload Weight; Models Support Energy-Saving Microwave Technologies; Materials Advance Chemical Propulsion Technology; and High-Temperature Coatings Offer Energy Savings.

Improved system integration for integrated gasification combined cycle (IGCC) systems.

PubMed

Frey, H Christopher; Zhu, Yunhua

2006-03-01

Integrated gasification combined cycle (IGCC) systems are a promising technology for power generation. They include an air separation unit (ASU), a gasification system, and a gas turbine combined cycle power block, and feature competitive efficiency and lower emissions compared to conventional power generation technology. IGCC systems are not yet in widespread commercial use and opportunities remain to improve system feasibility via improved process integration. A process simulation model was developed for IGCC systems with alternative types of ASU and gas turbine integration. The model is applied to evaluate integration schemes involving nitrogen injection, air extraction, and combinations of both, as well as different ASU pressure levels. The optimal nitrogen injection only case in combination with an elevated pressure ASU had the highest efficiency and power output and approximately the lowest emissions per unit output of all cases considered, and thus is a recommended design option. The optimal combination of air extraction coupled with nitrogen injection had slightly worse efficiency, power output, and emissions than the optimal nitrogen injection only case. Air extraction alone typically produced lower efficiency, lower power output, and higher emissions than all other cases. The recommended nitrogen injection only case is estimated to provide annualized cost savings compared to a nonintegrated design. Process simulation modeling is shown to be a useful tool for evaluation and screening of technology options.

Modelling of settlement territory flooding using geoinformation technologies

NASA Astrophysics Data System (ADS)

Zatserkovnyi, V. I.; Bogoslavskyi, M. D.

2016-10-01

The article describes the main problems concerned with area flooding. The ways to prevent and eliminate these problems are determined. It is proposed to use the GIS technologies in the fight against flooding. This can qualitatively improve monitoring of territories, save time and money.

How To Organize Technology Areas.

ERIC Educational Resources Information Center

Fickes, Michael

1998-01-01

Highlights three ways a college or university can organize its technology areas to maximize comfort and save space. Examples are provided on controlling equipment sprawl through thoughtful workstation development, designing computer rooms for flexibility and effective cable management, and emulating business setups that are work-flow efficient and…

Defense | NREL

Science.gov Websites

Maritime Academy training ships to test promising energy saving technologies and increase steaming days between refuelings. The Maritime Pre-Screening Assessment of Conservation Technologies (M-PACT) project uses a ship-board test-bed with sophisticated sensors and a calibrated model to evaluate new and

An Overview of the Beacon Monitor Operations Technology

NASA Technical Reports Server (NTRS)

Sue, Miles K.; Wyatt, E. Jay; Foster, Mike; Schlutsmeyer, Alan; Sherwood, Rob

1997-01-01

This paper summarizes the end-to-end design of a technology for low cost mission operations. Cost savings is achieved by reducing the total volume of downlinked engineering telemetry by decreasing the frequency of telemetry acquisition and the volume of data received per pass.

Advanced composites structural concepts and materials technologies for primary aircraft structures: Design/manufacturing concept assessment

NASA Technical Reports Server (NTRS)

Chu, Robert L.; Bayha, Tom D.; Davis, HU; Ingram, J. ED; Shukla, Jay G.

1992-01-01

Composite Wing and Fuselage Structural Design/Manufacturing Concepts have been developed and evaluated. Trade studies were performed to determine how well the concepts satisfy the program goals of 25 percent cost savings, 40 percent weight savings with aircraft resizing, and 50 percent part count reduction as compared to the aluminum Lockheed L-1011 baseline. The concepts developed using emerging technologies such as large scale resin transfer molding (RTM), automatic tow placed (ATP), braiding, out-of-autoclave and automated manufacturing processes for both thermoset and thermoplastic materials were evaluated for possible application in the design concepts. Trade studies were used to determine which concepts carry into the detailed design development subtask.

Integrated Application of Active Controls (IAAC) technology to an advanced subsonic transpot project-demonstration act system definition

NASA Technical Reports Server (NTRS)

Hanks, G. W.; Shomber, H. A.; Crumb, C. B.; Flora, C. C.; Macdonald, K. A. B.; Smith, R. D.; Sassi, A. P.; Dorwart, R. J.

1982-01-01

The 1985 ACT airplane is the Final Active Controls Technology (ACT) Airplane with the addition of three-axis fly by wire. Thus it retains all the efficiency features of the full ACT system plus the weight and cost savings accruing from deletion of the mechanical control system. The control system implements the full IAAC spectrum of active controls except flutter-mode control, judged essentially nonbeneficial, and incorporates new control surfaces called flaperons to make the most of wing-load alleviation. This redundant electronic system is conservatively designed to preserve the extreme reliability required of crucial short-period pitch augmentation, which provides more than half of the fuel savings.

Development of air conditioning technologies to reduce CO2 emissions in the commercial sector

PubMed Central

Yoshida, Yukiko

2006-01-01

Background Architectural methods that take into account global environmental conservation generally concentrate on mitigating the heat load of buildings. Here, we evaluate the reduction of carbon dioxide (CO2) emissions that can be achieved by improving heating, ventilating, and air conditioning (HVAC) technologies. Results The Climate Change Research Hall (CCRH) of the National Institute for Environmental Studies (NIES) is used as a case study. CCRH was built in line with the "Green Government Buildings" program of the Government Buildings Department at the Ministry of Land, Infrastructure and Transport in Japan. We have assessed the technology used in this building, and found that there is a possibility to reduce energy consumption in the HVAC system by 30%. Conclusion Saving energy reduces CO2 emissions in the commercial sector, although emission factors depend on the country or region. Consequently, energy savings potential may serve as a criterion in selecting HVAC technologies with respect to emission reduction targets. PMID:17062161

Electronic/electric technology benefits study. [avionics

NASA Technical Reports Server (NTRS)

Howison, W. W.; Cronin, M. J.

1982-01-01

The benefits and payoffs of advanced electronic/electric technologies were investigated for three types of aircraft. The technologies, evaluated in each of the three airplanes, included advanced flight controls, advanced secondary power, advanced avionic complements, new cockpit displays, and advanced air traffic control techniques. For the advanced flight controls, the near term considered relaxed static stability (RSS) with mechanical backup. The far term considered an advanced fly by wire system for a longitudinally unstable airplane. In the case of the secondary power systems, trades were made in two steps: in the near term, engine bleed was eliminated; in the far term bleed air, air plus hydraulics were eliminated. Using three commercial aircraft, in the 150, 350, and 700 passenger range, the technology value and pay-offs were quantified, with emphasis on the fiscal benefits. Weight reductions deriving from fuel saving and other system improvements were identified and the weight savings were cycled for their impact on TOGW (takeoff gross weight) and upon the performance of the airframes/engines. Maintenance, reliability, and logistic support were the other criteria.

Energy use and conservation trends, 1972--1986

DOE Office of Scientific and Technical Information (OSTI.GOV)

Klan, M.S.; Belzer, D.B.; Marsh, S.J.

1989-02-01

US trends in energy use and conservation since 1972 are analyzed in this report. That year represents the last year prior to significant energy price shocks. In 1986, an estimated 31.8 quads has been saved in the US compared with what consumption would have been if the energy use per dollar of GNP had continued on the same trend after 1972 as in the period 1960--1972. Actual US energy consumption in 1986 was 74.3 quads. It is clear that energy conservation is persistent and conservation investments continue to pay off even after initial energy price shocks have subsided. Separate analysesmore » have been conducted for the major end-use sectors (residential, commercial, industrial, and transportation). Savings have been estimated in each sector, and the factors contributing to sectoral savings identified. 19 refs., 23 figs., 26 tabs.« less

Are cooler surfaces a cost-effect mitigation of urban heat islands?

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pomerantz, Melvin

Much research has gone into technologies to mitigate urban heat islands by making urban surfaces cooler by increasing their albedos. To be practical, the benefit of the technology must be greater than its cost. Here, this report provides simple methods for quantifying the maxima of some benefits that albedo increases may provide. The method used is an extension of an earlier paper that estimated the maximum possible electrical energy saving achievable in an entire city in a year by a change of albedo of its surfaces. The present report estimates the maximum amounts and monetary savings of avoided CO 2more » emissions and the decreases in peak power demands. As examples, for several warm cities in California, a 0.2 increase in albedo of pavements is found to reduce CO 2 emissions by < 1 kg per m 2 per year. At the current price of CO 2 reduction in California, the monetary saving is < US$ 0.01 per year per m 2 modified. The resulting maximum peak-power reductions are estimated to be < 7% of the base power of the city. In conclusion, the magnitudes of the savings are such that decision-makers should choose carefully which urban heat island mitigation techniques are cost effective.« less

Are cooler surfaces a cost-effect mitigation of urban heat islands?

DOE PAGES

Pomerantz, Melvin

2017-04-20

Much research has gone into technologies to mitigate urban heat islands by making urban surfaces cooler by increasing their albedos. To be practical, the benefit of the technology must be greater than its cost. Here, this report provides simple methods for quantifying the maxima of some benefits that albedo increases may provide. The method used is an extension of an earlier paper that estimated the maximum possible electrical energy saving achievable in an entire city in a year by a change of albedo of its surfaces. The present report estimates the maximum amounts and monetary savings of avoided CO 2more » emissions and the decreases in peak power demands. As examples, for several warm cities in California, a 0.2 increase in albedo of pavements is found to reduce CO 2 emissions by < 1 kg per m 2 per year. At the current price of CO 2 reduction in California, the monetary saving is < US$ 0.01 per year per m 2 modified. The resulting maximum peak-power reductions are estimated to be < 7% of the base power of the city. In conclusion, the magnitudes of the savings are such that decision-makers should choose carefully which urban heat island mitigation techniques are cost effective.« less

The Impact of Technological Change on Work and Training. Tripartite European Meeting on the Impact of Technological Change on Work and Training (Geneva, Switzerland, October 28-November 2, 1991).

ERIC Educational Resources Information Center

International Labour Office, Geneva (Switzerland).

The first part of this report examines the relationship of technological change to employment and work. After a brief introduction, chapter 1 discusses new technology and labor productivity versus employment, emphasizing the effects of labor-saving machinery and changes in specific sectors of employment, such as electrical machinery,…

PubMed Central

DAMONTI, A.; MORELLI, P.; MUSSI, M.; PATREGNANI, C.; GARAGIOLA, E.; FOGLIA, E.; PAGANI, R.; CARMINATI, R.; PORAZZI, E.

2015-01-01

Summary Introduction. The objective of this paper is the comparison between two different technologies used for the removal of a uterine myoma, a frequent benign tumor: the standard technology currently used, laparoscopy, and an innovative one, colpoceliotomy. It was considered relevant to evaluate the real and the potential effects of the two technologies implementation and, in addition, the consequences that the introduction or exclusion of the innovative technology would have for both the National Health System (NHS) and the entire community. Methods. The comparison between these two different technologies, the standard and the innovative one, was conducted using a Health Technology Assessment (HTA). In particular, in order to analyse their differences, a multi-dimensional approach was considered: effectiveness, costs and budget impact analysis data were collected, applying different instruments, such as the Activity Based Costing methodology (ABC), the Cost-Effectiveness Analysis (CEA) and the Budget Impact Analysis (BIA). Organisational, equity and social impact were also evaluated. Results. The results showed that the introduction of colpoceliotomy would provide significant economic savings to the Regional and National Health Service; in particular, a saving of € 453.27 for each surgical procedure. Discussion. The introduction of the innovative technology, colpoceliotomy, could be considered a valuable tool; one offering many advantages related to less invasiveness and a shorter surgical procedure than the standard technology currently used (laparoscopy). PMID:26900330

Lidar as a Diagnostic of Smoke/Obscurants: Overview and Assessment of the Development with Recommendations

DTIC Science & Technology

1984-10-03

aerosol , and the name " laser radar" is used to denote systems de- signed for the detection of solid objects...34* MEASUREMENW OF T(Li) BY SEPARATE TRANSMISSOMETER . One method of measuring * T(Li) is by a separate transmissometer system operating at the lidar wavelength... transmissometer path may be radially outward from the lidar (along the lidar beam) to save the expense of scanning hardware in a developing lidar system ,

40 CFR 246.200-8 - Recommended procedures: Cost analysis.

Code of Federal Regulations, 2010 CFR

2010-07-01

...) SOLID WASTES SOURCE SEPARATION FOR MATERIALS RECOVERY GUIDELINES Requirements and Recommended Procedures..., storage, and transportation costs have been made, and estimated tonnages of both recoverable high-grade... for revenue from paper sales and savings from diverting recycled materials from disposal. Potential...

40 CFR 246.202-6 - Recommended procedures: Cost analysis.

Code of Federal Regulations, 2010 CFR

2010-07-01

..., storage and transportation costs have been made, and estimated tonnages of both recoverable material and...) SOLID WASTES SOURCE SEPARATION FOR MATERIALS RECOVERY GUIDELINES Requirements and Recommended Procedures... paper sales and savings from diverting recycled materials from disposal. Potential costs to upgrade...

40 CFR 246.201-7 - Recommended procedures: Cost analysis.

Code of Federal Regulations, 2010 CFR

2010-07-01

..., storage and transportation costs have been made, and estimated tonnages of both recoverable materials and...) SOLID WASTES SOURCE SEPARATION FOR MATERIALS RECOVERY GUIDELINES Requirements and Recommended Procedures... paper sales and savings from diverting recycled materials from disposal. Potential costs to upgrade...

An Operational Wake Vortex Sensor Using Pulsed Coherent Lidar

NASA Technical Reports Server (NTRS)

Barker, Ben C., Jr.; Koch, Grady J.; Nguyen, D. Chi

1998-01-01

NASA and FAA initiated a program in 1994 to develop methods of setting spacings for landing aircraft by incorporating information on the real-time behavior of aircraft wake vortices. The current wake separation standards were developed in the 1970's when there was relatively light airport traffic and a logical break point by which to categorize aircraft. Today's continuum of aircraft sizes and increased airport packing densities have created a need for re-evaluation of wake separation standards. The goals of this effort are to ensure that separation standards are adequate for safety and to reduce aircraft spacing for higher airport capacity. Of particular interest are the different requirements for landing under visual flight conditions and instrument flight conditions. Over the years, greater spacings have been established for instrument flight than are allowed for visual flight conditions. Preliminary studies indicate that the airline industry would save considerable money and incur fewer passenger delays if a dynamic spacing system could reduce separations at major hubs during inclement weather to the levels routinely achieved under visual flight conditions. The sensor described herein may become part of this dynamic spacing system known as the "Aircraft VOrtex Spacing System" (AVOSS) that will interface with a future air traffic control system. AVOSS will use vortex behavioral models and short-term weather prediction models in order to predict vortex behavior sufficiently into the future to allow dynamic separation standards to be generated. The wake vortex sensor will periodically provide data to validate AVOSS predictions. Feasibility of measuring wake vortices using a lidar was first demonstrated using a continuous wave (CW) system from NASA Marshall Space Flight Sensor and tested at the Volpe National Transportation Systems Center's wake vortex test site at JFK International Airport. Other applications of CW lidar for wake vortex measurement have been made more recently, including a system developed by the MIT Lincoln Laboratory. This lidar has been used for detailed measurements of wake vortex velocities in support of wake vortex model validation. The first measurements of wake vortices using a pulsed, lidar were made by Coherent Technologies, Inc. (CTI) using a 2 micron solid-state, flashlamp-pumped system operating at 5 Hz. This system was first deployed at Denver's Stapleton Airport. Pulsed lidar has been selected as the baseline technology for an operational sensor due to its longer range capability.

Interfacial damage identification of steel and concrete composite beams based on piezoceramic wave method.

PubMed

Yan, Shi; Dai, Yong; Zhao, Putian; Liu, Weiling

2018-01-01

Steel-concrete composite structures are playing an increasingly important role in economic construction because of a series of advantages of great stiffness, good seismic performance, steel material saving, cost efficiency, convenient construction, etc. However, in service process, due to the long-term effects of environmental impacts and dynamic loading, interfaces of a composite structure might generate debonding cracks, relative slips or separations, and so on, lowering the composite effect of the composite structure. In this paper, the piezoceramics (PZT) are used as transducers to perform experiments on interface debonding slips and separations of composite beams, respectively, aimed at proposing an interface damage identification model and a relevant damage detection innovation method based on PZT wave technology. One part of various PZT patches was embedded in concrete as "smart aggregates," and another part of the PZT patches was pasted on the surface of the steel beam flange, forming a sensor array. A push-out test for four specimens was carried out and experimental results showed that, under the action of the external loading, the received signal amplitudes will increasingly decrease with increase of debonding slips along the interface. The proposed signal energy-based interface damage detection algorithm is highly efficient in surface state evaluations of composite beams.

Environmental impact assessment of solid waste management in Beijing City, China

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhao Yan; Key Laboratory for Solid Waste Management and Environment Safety, Ministry of Education of China, Tsinghua University, 100084 Beijing; Christensen, Thomas H.

2011-04-15

The environmental impacts of municipal solid waste management in Beijing City were evaluated using a life-cycle-based model, EASEWASTE, to take into account waste generation, collection, transportation, treatment/disposal technologies, and savings obtained by energy and material recovery. The current system, mainly involving the use of landfills, has manifested significant adverse environmental impacts caused by methane emissions from landfills and many other emissions from transfer stations. A short-term future scenario, where some of the landfills (which soon will reach their capacity because of rising amount of waste in Beijing City) are substituted by incinerators with energy recovery, would not result in significantmore » environmental improvement. This is primarily because of the low calorific value of mixed waste, and it is likely that the incinerators would require significant amounts of auxiliary fuels to support combustion of wet waste. As for the long-term future scenario, efficient source separation of food waste could result in significant environmental improvements, primarily because of increase in calorific value of remaining waste incinerated with energy recovery. Sensitivity analysis emphasized the importance of efficient source separation of food waste, as well as the electricity recovery in incinerators, in order to obtain an environmentally friendly waste management system in Beijing City.« less

Predicting Cloud Computing Technology Adoption by Organizations: An Empirical Integration of Technology Acceptance Model and Theory of Planned Behavior

ERIC Educational Resources Information Center

Ekufu, ThankGod K.

2012-01-01

Organizations are finding it difficult in today's economy to implement the vast information technology infrastructure required to effectively conduct their business operations. Despite the fact that some of these organizations are leveraging on the computational powers and the cost-saving benefits of computing on the Internet cloud, others…

Radiant Barriers Save Energy in Buildings

NASA Technical Reports Server (NTRS)

2014-01-01

Langley Research Center needed to coat the Echo 1 satellite with a fine mist of vaporized metal, and collaborated with industry to create "radiant barrier technology." In 2010, Ryan Garrett learned about a new version of the technology resistant to oxidation and founded RadiaSource in Ogden, Utah, to provide the NASA-derived technology for applications in homes, warehouses, gymnasiums, and agricultural settings.

A Compendium of Energy Conservation Success Stories

DOE R&D Accomplishments Database

1988-09-01

Three-quarters of DOE's Conservation R and D funds have been devoted to technology research and development: basic and applied research, exploratory R and D, engineering feasibility studies, pilot-scale prototype R and D, and technology demonstration. Non R and D projects have involved technology assessment program planning and analysis, model development, technology transfer and consumer information, health effects and safety research, and technical support for rule making. The success stories summarized in this compendium fall into three general categories: Completed Technology Success Stories, projects that have resulted in new energy-saving technologies that are presently being used in the private sector; Technical Success Stories, projects that have produced or disseminated important scientific/technical information likely to result in future energy savings; Program Success Stories, non-R and D activities that have resulted in nationally significant energy benefits. The Energy Conservation research and development program at DOE is managed by the Office of Conservation under the direction of the Deputy Assistant Secretary for Conservation. Three subordinate Program Offices correspond to the buildings, transportation, and industrial end-use sectors. A fourth subordinate Program Office{endash}Energy Utilization Research{endash}sponsors research and technical inventions for all end-use sectors.

47 CFR 201.3 - Policy.

Code of Federal Regulations, 2010 CFR

2010-10-01

... OFFICE OF SCIENCE AND TECHNOLOGY POLICY AND NATIONAL SECURITY COUNCIL EXECUTIVE POLICY § 201.3 Policy. (a..., postattack resources will be assigned to activities concerned with the maintenance and saving of lives... and recovery. (g) The Director of the Office of Science and Technology Policy will serve as the...

The Use of Technology for STD Partner Services in the United States: A Structured Review.

PubMed

Kachur, Rachel; Hall, Wendasha; Coor, Alexandra; Kinsey, Jennine; Collins, Dayne; Strona, F V

2018-05-01

Since the late 1990s, health departments and STD programs throughout the U.S. have used technologies, such as the internet and mobile phones, to provide services to persons with a sexually transmitted infection, including HIV, and their sex partners, also known as partner services. This study reviewed the published literature to assess and compare partner services outcomes as a result of using technology and to calculate cost savings through cases averted. We conducted a structured literature review of all U.S. studies that examined the use of technology to notify persons exposed to an STD (syphilis, chlamydia, gonorrhea), including HIV, by health care professionals in the U.S. from 2000 to 2017. Outcome measures, including the number of the number of partners notified, screened or tested; and new positives identified, were captured and cost savings were calculated, when data were available. Seven studies were identified. Methods used for partner services differed across studies, although email was the primary mode in 6 (83%) of the 7 studies. Only 2 of the 7 studies compared use of technology for partner services to traditional partner services. Between 10% and 97% of partners were successfully notified of their exposure through the use of technology and between 34% and 81% were screened or tested. Five studies reported on new infections identified, which ranged from 3-19. Use of technology for partner serves saved programs between $22,795 and $45,362 in direct and indirect medical costs. Use of technology for partner services increased the number of partners notified, screened or tested, and new infections found. Importantly, the use of technology allowed programs to reach partners who otherwise would not have been notified of their exposure to an STD or HIV. Improved response times and time to treatment were also seen as was re-engagement into care for previous HIV positive patients. Data and outcome measures across the studies were not standardized, making it difficult to generalize conclusions. Although not a replacement for traditional partner services, the use of technology enhances partner service outcomes.

Survey of electrochemical metal winning processes. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vaaler, L.E.

1979-03-01

The subject program was undertaken to find electrometallurgical technology that could be developed into energy saving commercial metal winning processes. Metals whose current production processes consume significant energy (excepting copper and aluminum) are magnesium, zinc, lead, chromium, manganese, sodium, and titanium. The technology of these metals, with the exception of titanium, was reviewed. Growth of titanium demand has been too small to justify the installation of an electrolyte process that has been developed. This fact and the uncertainty of estimates of future demand dissuaded us from reviewing titanium technology. Opportunities for developing energy saving processes were found for magnesium, zinc,more » lead, and sodium. Costs for R and D and demonstration plants have been estimated. It appeared that electrolytic methods for chromium and manganese cannot compete energywise or economically with the pyrometallurgical methods of producing the ferroalloys, which are satisfactory for most uses of chromium and manganese.« less

Peculiarities of non-autoclaved lime wall materials production using clays

NASA Astrophysics Data System (ADS)

Volodchenko, A. A.; Lesovik, V. S.; Cherepanova, I. A.; Volodchenko, A. N.; Zagorodnjuk, L. H.; Elistratkin, M. Y.

2018-03-01

At present, the development and implementation of energy saving technologies for building materials production, which correspond to modern trends of «green» technologies, become ever more popular. One of the most widely spread wall materials today is a lime brick and stones. The primary raw goods used in production of such materials are quarziferous rocks. However, they have some disadvantages, including low strength index at the intermediate phase of their production, especially in case with a raw brick, which is an issue in the production of high-hollow goods due to low strength index of raw materials and the nonoptimal matrix structure. The conducted experiments confirmed the possibility to control structurization of building composites due to application of nonconventional argillous raw materials. Besides, the material and mineral composition of nonconventional clay rocks ensures the optimal microstructure thus providing for the production of efficient wall building materials via energy saving technology.

Problems of Technology of Energy-Saving Buildings and Their Impact on Energy Efficiency in Buildings

NASA Astrophysics Data System (ADS)

Kwasnowski, Pawel; Fedorczak-Cisak, Malgorzata; Knap, Katarzyna

2017-10-01

Introduction of EPBD in legislation of the EU member states caused that buildings must meet very stringent requirements of thermal protection and energy efficiency. On the basis of EPBD provisions, EU Member States introduce standard of NZEB (Nearly Zero-Energy Buildings). Such activities cause a need for new, innovative materials and technologies, and new approaches to design, construction and retrofitting of buildings. Indispensable is the precise coordination of the design of structure and technical installations of building, which may be provided in an integrated design process in the system BIM. Good coordination and cooperation of all contractors during the construction phase is also necessary. The article presents the problems and the new methodology for the design, construction and use of energy efficient buildings in terms of energy saving technologies, including discussion of the significant impact of the automation of technical installations on the building energy efficiency.

Options for reducing carbon dioxide emissions

NASA Astrophysics Data System (ADS)

Rosenfeld, Arthur H.; Price, Lynn

1992-03-01

Improvements in energy efficiency can significantly reduce the annual growth in greenhouse gas emissions. Such improvements occur when energy intensity is reduced; no reduction in energy services is required. Using the concept of ``cost of conserved energy'' to develop conservation supply curves similar to resource supply curves, researchers consistently find that electricity and natural gas savings of nearly 50% of current consumption are possible for U.S. buildings. Such reductions in energy consumption directly reduce emissions of greenhouse gases. To capture these savings, we must continue to develop energy-efficient technologies and strategies. This paper describes three recent energy-efficient technologies that benefitted from energy conservation research and development (R&D) funding: high-frequency ballasts, compact fluorescent lamps, and low-emissivity windows. Other advanced technologies and strategies of spectrally selective windows, superwindows, electrochromic windows, advanced insulation, low-flow showerheads, improved recessed lamp fixtures, whitening surfaces and planting urban trees, daylighting, and thermal energy storage are also discussed.

High-content screening in microfluidic devices.

PubMed

Cheong, Raymond; Paliwal, Saurabh; Levchenko, Andre

2010-08-01

Miniaturization is the key to advancing the state of the art in high-content screening (HCS) in order to enable dramatic cost savings through reduced usage of expensive biochemical reagents and to enable large-scale screening on primary cells. Microfluidic technology offers the potential to enable HCS to be performed with an unprecedented degree of miniaturization. This perspective highlights a real-world example from the authors’ work of HCS assays implemented in a highly miniaturized microfluidic format. The advantages of this technology are discussed, including cost savings, high-throughput screening on primary cells, improved accuracy, the ability to study complex time-varying stimuli, and ease of automation, integration and scaling. The reader will understand the capabilities of anew microfluidics-based platform for HCS and the advantages it provides over conventional plate-based HCS. Microfluidics technology will drive significant advancements and broader usage and applicability of HCS in drug discovery.

Experimental research on the application of HTAC in small-size heating furnace

NASA Astrophysics Data System (ADS)

Zhou, Yu; Qin, Chaokui; Yang, Jun; Chen, Zhiguang

2018-03-01

High temperature air combustion (HTAC) technology, which is also known as regenerative combustion technology, has realized energy saving, CO2 and NOx emissions reduction and low-noise combustion. It has been widely applied in various types of heating furnace and has achieved good energy-saving effect. However, there is little application of this technology in small-size furnace. In this paper, a small-size regenerative heating furnace was built in the laboratory and experiments were carried out on it. The result shows that, if the transport frequency was set to a group per min, the center temperature of processed workpiece at the rated conditions (i.e. burner power is 300 kW and switching time is 60s) reached 1133°C. And the efficiency of the heating furnace was 36.8%. Then the derived comprehensive heat transfer coefficient was 168 W/(m2˙°C).

DOE Office of Scientific and Technical Information (OSTI.GOV)

Perrin, Tess E.; Davis, Robert G.; Wilkerson, Andrea M.

This GATEWAY project evaluated four field installations to better understand the long-term performance of a number of LED products, which can hopefully stimulate improvements in designing, manufacturing, specifying, procuring, and installing LED products. Field studies provide the opportunity to discover and investigate issues that cannot be simulated or uncovered in a laboratory, but the installed performance over time of commercially available LED products has not been well documented. Improving long-term performance can provide both direct energy savings by reducing the need to over-light to account for light loss and indirect energy savings through better market penetration due to SSL’s competitivemore » advantages over less-efficient light source technologies. The projects evaluated for this report illustrate that SSL use is often motivated by advantages other than energy savings, including maintenance savings, easier integration with control systems, and improved lighting quality.« less

Sara Lee: Improved Compressed Air System Increases Efficiency and Saves Energy at an Industrial Bakery

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

This case study was prepared for the Industrial Technologies Program of the U.S. Department of Energy (DOE); it describes the energy and costs savings resulting from improving the compressed air system of a large Sara Lee bakery in Sacramento, California. The compressed air system supports many operations of the bread-making machines, and it had been performing poorly. A specialist from Draw Professional Services, a DOE Allied Partner, evaluated the system, and his suggestions included repairing a controller, fixing leaks, and replacing a compressor with a new one fitted with an energy-saving variable-speed drive. As a result, the bakery has reducedmore » its energy use by 471,000 kilowatt-hours annually and is saving $50,000 per year in operating and maintenance costs.« less

Spinoff 2015

NASA Technical Reports Server (NTRS)

2015-01-01

Topics covered include: 3D Endoscope to Boost Safety, Cut Cost of Surgery; Audio App Brings a Better Night's Sleep Liquid Cooling Technology Increases Exercise Efficiency; Algae-Derived Dietary Ingredients Nourish Animals; Space Grant Research Launches Rehabilitation Chair; Vision Trainer Teaches Focusing Techniques at Home; Aircraft Geared Architecture Reduces Fuel Cost and Noise; Ubiquitous Supercritical Wing Design Cuts Billions in Fuel Costs; Flight Controller Software Protects Lightweight Flexible Aircraft; Cabin Pressure Monitors Notify Pilots to Save Lives; Ionospheric Mapping Software Ensures Accuracy of Pilots' GPS; Water Mapping Technology Rebuilds Lives in Arid Regions; Shock Absorbers Save Structures and Lives during Earthquakes; Software Facilitates Sharing of Water Quality Data Worldwide; Underwater Adhesives Retrofit Pipelines with Advanced Sensors; Laser Imaging Video Camera Sees through Fire, Fog, Smoke; 3D Lasers Increase Efficiency, Safety of Moving Machines; Air Revitalization System Enables Excursions to the Stratosphere; Magnetic Fluids Deliver Better Speaker Sound Quality; Bioreactor Yields Extracts for Skin Cream; Private Astronaut Training Prepares Commercial Crews of Tomorrow; Activity Monitors Help Users Get Optimum Sun Exposure; LEDs Illuminate Bulbs for Better Sleep, Wake Cycles; Charged Particles Kill Pathogens and Round Up Dust; Balance Devices Train Golfers for a Consistent Swing; Landsat Imagery Enables Global Studies of Surface Trends; Ruggedized Spectrometers Are Built for Tough Jobs; Gas Conversion Systems Reclaim Fuel for Industry; Remote Sensing Technologies Mitigate Drought; Satellite Data Inform Forecasts of Crop Growth; Probes Measure Gases for Environmental Research; Cloud Computing Technologies Facilitate Earth Research; Software Cuts Homebuilding Costs, Increases Energy Efficiency; Portable Planetariums Teach Science; Schedule Analysis Software Saves Time for Project Planners; Sound Modeling Simplifies Vehicle Noise Management; Custom 3D Printers Revolutionize Space Supply Chain; Improved Calibration Shows Images' True Colors; Micromachined Parts Advance Medicine, Astrophysics, and More; Metalworking Techniques Unlock a Unique Alloy; Low-Cost Sensors Deliver Nanometer-Accurate Measurements; Electrical Monitoring Devices Save on Time and Cost; Dry Lubricant Smooths the Way for Space Travel, Industry; and Compact Vapor Chamber Cools Critical Components.

Potential savings associated with drug substitution in Medicare Part D: the Translating Research into Action for Diabetes (TRIAD) study.

PubMed

Duru, O Kenrik; Ettner, Susan L; Turk, Norman; Mangione, Carol M; Brown, Arleen F; Fu, Jeffery; Simien, Leslie; Tseng, Chien-Wen

2014-01-01

Drug substitution is a promising approach to reducing medication costs. To calculate the potential savings in a Medicare Part D plan from generic or therapeutic substitution for commonly prescribed drugs. Cross-sectional, simulation analysis. Low-income subsidy (LIS) beneficiaries (n = 145,056) and non low-income subsidy (non-LIS) beneficiaries (n = 1,040,030) enrolled in a large, national Part D health insurer in 2007 and eligible for a possible substitution. Using administrative data from 2007, we identified claims filled for brand-name drugs for which a direct generic substitute was available. We also identified the 50 highest cost drugs separately for LIS and non-LIS beneficiaries, and reached consensus on which drugs had possible therapeutic substitutes (27 for LIS, 30 for non-LIS). For each possible substitution, we used average daily costs of the original and substitute drugs to calculate the potential out-of-pocket savings, health plan savings, and when applicable, savings for the government/LIS subsidy. Overall, 39 % of LIS beneficiaries and 51 % of non-LIS beneficiaries were eligible for a generic and/or therapeutic substitution. Generic substitutions resulted in an average annual savings of $160 in the case of LIS beneficiaries and $127 in the case of non-LIS beneficiaries. Therapeutic substitutions resulted in an average annual savings of $452 in the case of LIS beneficiaries and $389 in the case of non-LIS beneficiaries. Our findings indicate that drug substitution, particularly therapeutic substitution, could result in significant cost savings. There is a need for additional studies evaluating the acceptability of therapeutic substitution interventions within Medicare Part D.

Enhanced Oxidative Dehydrogenation of Ethane with Facilitated Transport Membranes for Low Cost Production of Ethylene

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nemser, Stuart; Shangguan, Ning; Pennisi, Kenneth

This SBIR program has been extremely successful. We have met or exceeded all of the key objectives. We have successfully demonstrated the product and process feasibility. Compact Membrane Systems proposed a membrane separation technology which can efficiently separate ethylene from ethane in the presence of H 2O and CO 2. The CMS ethylene/ethane separation will significantly improve the economics of the Oxidative Dehydrogenation (ODH) process. We have developed membranes with high ethylene flux and high ethylene/ethane selectivity. These membranes have also shown good resistance to high concentration CO 2 and CO. Economic analysis shows at least **% cost savings comparedmore » with conventional distillation used for ethylene/ethane separation. Given our success to date, we have been able to establish key direct partnerships with other collaborators. The primary objective of the Phase I program was to develop a stable membrane that is capable of providing very efficient and cost effective production of ethylene from ethane. The CMS fluorinated membrane developed during this program was found to be able to provide very good C 2H 4/C 2H 6 selectivity and outstanding C 2H 4 permeance. With the development of the fast and highly selective ethylene CMS membrane, we have achieved all our Phase I program objectives. This is especially true of the estimated cost of ethylene production that is projected to be over **% less than the conventional method (distillation) at scale applications (** Nm3/h). The final result is better than the Phase I goal of 30% less. In summary, during the Phase I, we developed a CMS membrane with a high C 2H 4 permeance good C 2H 4/C 2H 6 selectivity. The stability and anti-fouling ability of the CMS membrane was demonstrated by exposing the membrane to a C 2H 4/C 2H 6 mixture gas for 7 weeks. A membrane based ODH production and separation system was designed and the economic and engineering evaluation using the VMGSim models predicted a cost of $***. As previously stated this is at least a 35% cost reduction from the conventional methods and higher than the Phase I goal (25% cost reduction). The successful Phase I research attracted the interest from several major industrial players who are willing to provide partnership and support of further research. Successful development of the fluoropolymer membranes for C 2H 4/C 2H 6 separation in the process of ODH will provide significant benefits to the public: 1. Development of a highly economically profitable use of shale gas resource; 2. More economic growth and job creations based on the rich shale gas resource in US; 3. Huge energy savings compared with the conventional production of ethylene.« less

Directional Gila River crossing saves construction, mitigation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Saylor, L.A.

1994-12-01

Directional drilled river crossing technology gained a new convert this fall as El Paso Natural Gas Co. (EPNG) replaced a washed out 10 3/4-in. line that crossed the Gila River and two irrigation canals near Yuma, Ariz. The 1,650-ft bore, the company's first drilled river crossing, saved both construction costs and environmental reporting and mitigation expenses. This paper reviews the planning, engineering, and equipment used to install this river pipeline crossing.

Demonstration of Energy Savings in Commercial Buildings for Tiered Trim and Respond Method in Resetting Static Pressure for VAV Systems

DTIC Science & Technology

2017-03-01

FINAL REPORT Demonstration of Energy Savings in Commercial Buildings for Tiered Trim and Respond Method in Resetting Static Pressure for VAV...release Page Intentionally Left Blank This report was prepared under contract to the Department of Defense Environmental Security Technology...Certification Program (ESTCP). The publication of this report does not indicate endorsement by the Department of Defense, nor should the contents be

CHARACTERIZING COSTS, SAVINGS AND BENEFITS OF A SELECTION OF ENERGY EFFICIENT EMERGING TECHNOLOGIES IN THE UNITED STATES

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xu, T.; Slaa, J.W.; Sathaye, J.

2010-12-15

Implementation and adoption of efficient end-use technologies have proven to be one of the key measures for reducing greenhouse gas (GHG) emissions throughout the industries. In many cases, implementing energy efficiency measures is among one of the most cost effective investments that the industry could make in improving efficiency and productivity while reducing CO2 emissions. Over the years, there have been incentives to use resources and energy in a cleaner and more efficient way to create industries that are sustainable and more productive. With the working of energy programs and policies on GHG inventory and regulation, understanding and managing themore » costs associated with mitigation measures for GHG reductions is very important for the industry and policy makers around the world. Successful implementation of emerging technologies not only can help advance productivities and competitiveness but also can play a significant role in mitigation efforts by saving energy. Providing evaluation and estimation of the costs and energy savings potential of emerging technologies is the focus of our work in this project. The overall goal of the project is to identify and select emerging and under-utilized energy-efficient technologies and practices as they are important to reduce energy consumption in industry while maintaining economic growth. This report contains the results from performing Task 2"Technology evaluation" for the project titled"Research Opportunities in Emerging and Under-Utilized Energy-Efficient Industrial Technologies," which was sponsored by California Energy Commission and managed by CIEE. The project purpose is to analyze market status, market potential, and economic viability of selected technologies applicable to the U.S. In this report, LBNL first performed re-assessments of all of the 33 emerging energy-efficient industrial technologies, including re-evaluation of the 26 technologies that were previously identified by Martin et al. (2000) and their potential significance to energy use in the industries, and new evaluation of additional seven technologies. The re-assessments were essentially updated with recent information that we searched and collected from literature to the extent possible. The progress of selected technologies as they diffused into the marketplace from 2000 to 2010 was then discussed in this report. The report also includes updated detailed characterizations of 15 technologies studied in 2000, with comparisons noted.« less

Pericarditis

MedlinePlus

... Daily Conferences Fellowships and Residencies School of Perfusion Technology Education Resources Library & Learning Resource Center CME Resources THI Journal THI Cardiac Society Save the Date: International Symposium on Cardiovascular Regenerative ...

Cardiomyopathy

MedlinePlus

... Daily Conferences Fellowships and Residencies School of Perfusion Technology Education Resources Library & Learning Resource Center CME Resources THI Journal THI Cardiac Society Save the Date: International Symposium on Cardiovascular Regenerative ...

Cyanosis

MedlinePlus

... Daily Conferences Fellowships and Residencies School of Perfusion Technology Education Resources Library & Learning Resource Center CME Resources THI Journal THI Cardiac Society Save the Date: International Symposium on Cardiovascular Regenerative ...

Performance evaluation of hybrid VLC using device cost and power over data throughput criteria

NASA Astrophysics Data System (ADS)

Lee, C. C.; Tan, C. S.; Wong, H. Y.; Yahya, M. B.

2013-09-01

Visible light communication (VLC) technology has attained its attention in both academic and industry lately. It is determined by the development of light emitting diode (LED) technology for solid-state lighting (SSL).It has great potential to gradually replace radio frequency (RF) wireless technology because it offers unregulated and unlicensed bandwidth to withstand future demand of indoor wireless access to real-time bandwidth-demanding applications. However, it was found to provide intrusive uplink channel that give rise to unpleasant irradiance from the user device which could interfere with the downlink channel of VLC and hence limit mobility to users as a result of small coverage (field of view of VLC).To address this potential problem, a Hybrid VLC system which integrates VLC (for downlink) and RF (for uplink) technology is proposed. It offers a non-intrusive RF back channel that provides high throughput VLC and maintains durability with conventional RF devices. To deploy Hybrid VLC system in the market, it must be energy and cost saving to attain its equivalent economical advantage by comparing to existing architecture that employs fluorescent or LED lights with RF technology. In this paper, performance evaluation on the proposed hybrid system was carried out in terms of device cost and power consumption against data throughput. Based on our simulation, Hybrid VLC system was found to reduce device cost by 3% and power consumption by 68% when compares to fluorescent lights with RF technology. Nevertheless, when it is compared to LED lights with RF technology, our proposed hybrid system is found to achieve device cost saving as high as 47% and reduced power consumption by 49%. Such promising results have demonstrated that Hybrid VLC system is a feasible solution and has paved the way for greater cost saving and energy efficient compares with the current RF architecture even with the increasing requirement of indoor area coverage.

How to "Kill a Watt" and Save Energy

ERIC Educational Resources Information Center

Massiha, G. H.; Houston, Shelton; Rawat, Kuldeep S.

2011-01-01

Many technology students--and especially those interested in environmental and energy issues--can benefit from learning about power ratings and the energy usage of electrical systems like the electrical equipment and appliances found in most homes. Students enrolled in electronics and construction technology courses learn to determine the power…

Fed Up with Delays, a President Pushes To Outsource Technology Operations.

ERIC Educational Resources Information Center

Olsen, Florence

2002-01-01

Discusses how officials at Salt Lake Community College decided the only way they could get the kind of technology service they needed was to hire a company to run the operation; the plan will not save money, but seeks better service and room for expansion. (EV)

Corporate Energy Conservation Program for Alcoa North American Extrusions: Office of Industrial Technologies (OIT) Aluminum BestPractices Management Case Study

DOE Office of Scientific and Technical Information (OSTI.GOV)

U.S. Department of Energy

2001-08-06

This case study is the latest in a series on industrial firms who are implementing energy efficient technologies and system improvements into their manufacturing processes. The case studies document the activities, savings, and lessons learned on these projects.

Teach Efficient Production with Modular Fixturing Pallets

ERIC Educational Resources Information Center

Creger, Don W.; Payne, Brent A.

2010-01-01

Advances in technology have yielded computer numerical control (CNC) machines and computer-aided manufacturing (CAM) software that saves time and increases productivity in today's industrial world. Training students to understand and use these technologies has become a key ingredient in preparing them for work in industry. Teachers of machining…

THE AFFORDABLE BIOSHELTERS PROJECT: TESTING INNOVATIVE TECHNOLOGIES, WORKING TO MAKE HIGH PERFORMANCE SOLAR GREENHOUSES COST COMPETITIVE

EPA Science Inventory

The economic feasibility and limitations of technologies investigated will be evaluated, including for liquid foam insulation, subsoil heat storages, and compost exhaust heating. These systems will save most of the energy and money spent to heat greenhouses in exchange for a h...

Technological Development and Its Implications for Educational Planning.

ERIC Educational Resources Information Center

Sanyal, Bikas C.

The phenomenon of technological development has assumed great importance in the contemporary world. It is reflected in unprecedented growth in productivity with accompanying labor saving, in improvement of quality of products, in the launching of new products and services, and in the development of new branches of activity. This document reports…

Construction Program Saved! Partnership Revitalizes School of Applied Technology

ERIC Educational Resources Information Center

LaPlaca, Joseph

2010-01-01

The Edison School of Applied Technology, a comprehensive public high school, has long had a reputation for producing top-notch crafts workers, tradespeople, project managers, estimators, and industry leaders. The school's graduates helped build the city and many currently have successful, productive careers in the public and private sectors. But…

Saving Time with Technology

ERIC Educational Resources Information Center

Gullen, Kristine; Zimmerman, Holly

2013-01-01

In order to help teachers envision digital products in action in classrooms, the authors look at three examples of how teachers they know enhance learning time by employing technology efficiently. The examples include: (1) a social studies teacher who begins each class period with a three-question formative assessment using the website…

Impact of Radiation Hardness and Operating Temperatures of Silicon Carbide Electronics on Space Power System Mass

NASA Technical Reports Server (NTRS)

Juhasz, Albert J.; Tew, Roy C.; Schwarze, Gene E.

1998-01-01

The effect of silicon carbide (SiC) electronics operating temperatures on Power Management and Distribution (PMAD), or Power Conditioning (PC), subsystem radiator size and mass requirements was evaluated for three power output levels (100 kW(e) , 1 MW(e), and 10 MW(e)) for near term technology ( i.e. 1500 K turbine inlet temperature) Closed Cycle Gas Turbine (CCGT) power systems with a High Temperature Gas Reactor (HTGR) heat source. The study was conducted for assumed PC radiator temperatures ranging from 370 to 845 K and for three scenarios of electrical energy to heat conversion levels which needed to be rejected to space by means of the PC radiator. In addition, during part of the study the radiation hardness of the PC electronics was varied at a fixed separation distance to estimate its effect on the mass of the instrument rated reactor shadow shield. With both the PC radiator and the conical shadow shield representing major components of the overall power system the influence of the above on total power system mass was also determined. As expected, results show that the greatest actual mass savings achieved by the use of SiC electronics occur with high capacity power systems. Moreover, raising the PC radiator temperature above 600 K yields only small additional system mass savings. The effect of increased radiation hardness on total system mass is to reduce system mass by virtue of lowering the shield mass.

Advanced Active Thermal Control Systems Architecture Study

NASA Technical Reports Server (NTRS)

Hanford, Anthony J.; Ewert, Michael K.

1996-01-01

The Johnson Space Center (JSC) initiated a dynamic study to determine possible improvements available through advanced technologies (not used on previous or current human vehicles), identify promising development initiatives for advanced active thermal control systems (ATCS's), and help prioritize funding and personnel distribution among many research projects by providing a common basis to compare several diverse technologies. Some technologies included were two-phase thermal control systems, light-weight radiators, phase-change thermal storage, rotary fluid coupler, and heat pumps. JSC designed the study to estimate potential benefits from these various proposed and under-development thermal control technologies for five possible human missions early in the next century. The study compared all the technologies to a baseline mission using mass as a basis. Each baseline mission assumed an internal thermal control system; an external thermal control system; and aluminum, flow-through radiators. Solar vapor compression heat pumps and light-weight radiators showed the greatest promise as general advanced thermal technologies which can be applied across a range of missions. This initial study identified several other promising ATCS technologies which offer mass savings and other savings compared to traditional thermal control systems. Because the study format compares various architectures with a commonly defined baseline, it is versatile and expandable, and is expected to be updated as needed.

Energy and emissions saving potential of additive manufacturing: the case of lightweight aircraft components

DOE PAGES

Huang, Runze; Riddle, Matthew; Graziano, Diane; ...

2015-05-08

Additive manufacturing (AM) holds great potential for improving materials efficiency, reducing life-cycle impacts, and enabling greater engineering functionality compared to conventional manufacturing (CM) processes. For these reasons, AM has been adopted by a growing number of aircraft component manufacturers to achieve more lightweight, cost-effective designs. This study estimates the net changes in life-cycle primary energy and greenhouse gas emissions associated with AM technologies for lightweight metallic aircraft components through the year 2050, to shed light on the environmental benefits of a shift from CM to AM processes in the U.S. aircraft industry. A systems modeling framework is presented, with integratesmore » engineering criteria, life-cycle environmental data, and aircraft fleet stock and fuel use models under different AM adoption scenarios. Estimated fleetwide life-cycle primary energy savings in a rapid adoption scenario reach 70-174 million GJ/year in 2050, with cumulative savings of 1.2-2.8 billion GJ. Associated cumulative emission reduction potentials of CO2e were estimated at 92.8-217.4 million metric tons. About 95% of the savings is attributed to airplane fuel consumption reductions due to lightweighting. In addition, about 4050 tons aluminum, 7600 tons titanium and 8100 tons of nickel alloys could be saved per year in 2050. The results indicate a significant role of AM technologies in helping society meet its long-term energy use and GHG emissions reduction goals, and highlight barriers and opportunities for AM adoption for the aircraft industry.« less

Energy and emissions saving potential of additive manufacturing: the case of lightweight aircraft components

DOE Office of Scientific and Technical Information (OSTI.GOV)

Huang, Runze; Riddle, Matthew; Graziano, Diane

Additive manufacturing (AM) holds great potential for improving materials efficiency, reducing life-cycle impacts, and enabling greater engineering functionality compared to conventional manufacturing (CM) processes. For these reasons, AM has been adopted by a growing number of aircraft component manufacturers to achieve more lightweight, cost-effective designs. This study estimates the net changes in life-cycle primary energy and greenhouse gas emissions associated with AM technologies for lightweight metallic aircraft components through the year 2050, to shed light on the environmental benefits of a shift from CM to AM processes in the U.S. aircraft industry. A systems modeling framework is presented, with integratesmore » engineering criteria, life-cycle environmental data, and aircraft fleet stock and fuel use models under different AM adoption scenarios. Estimated fleetwide life-cycle primary energy savings in a rapid adoption scenario reach 70-174 million GJ/year in 2050, with cumulative savings of 1.2-2.8 billion GJ. Associated cumulative emission reduction potentials of CO2e were estimated at 92.8-217.4 million metric tons. About 95% of the savings is attributed to airplane fuel consumption reductions due to lightweighting. In addition, about 4050 tons aluminum, 7600 tons titanium and 8100 tons of nickel alloys could be saved per year in 2050. The results indicate a significant role of AM technologies in helping society meet its long-term energy use and GHG emissions reduction goals, and highlight barriers and opportunities for AM adoption for the aircraft industry.« less

Discover CHP

EPA Pesticide Factsheets

Access information about how CHP systems work; their efficiency, environmental, economic, and reliability benefits; the cost and performance characteristics of CHP technologies; and how to calculate CHP efficiency emissions savings.

Fetal Heart

MedlinePlus

... Daily Conferences Fellowships and Residencies School of Perfusion Technology Education Resources Library & Learning Resource Center CME Resources THI Journal THI Cardiac Society Save the Date: International Symposium on Cardiovascular Regenerative ...

Rheumatic Fever

MedlinePlus

... Daily Conferences Fellowships and Residencies School of Perfusion Technology Education Resources Library & Learning Resource Center CME Resources THI Journal THI Cardiac Society Save the Date: International Symposium on Cardiovascular Regenerative ...

Silent Ischemia

MedlinePlus

... Daily Conferences Fellowships and Residencies School of Perfusion Technology Education Resources Library & Learning Resource Center CME Resources THI Journal THI Cardiac Society Save the Date: International Symposium on Cardiovascular Regenerative ...

Pulmonary Atresia

MedlinePlus

... Daily Conferences Fellowships and Residencies School of Perfusion Technology Education Resources Library & Learning Resource Center CME Resources THI Journal THI Cardiac Society Save the Date: International Symposium on Cardiovascular Regenerative ...

Vulnerable Plaque

MedlinePlus

... Daily Conferences Fellowships and Residencies School of Perfusion Technology Education Resources Library & Learning Resource Center CME Resources THI Journal THI Cardiac Society Save the Date: International Symposium on Cardiovascular Regenerative ...

Intravascular Ultrasound

MedlinePlus

... Daily Conferences Fellowships and Residencies School of Perfusion Technology Education Resources Library & Learning Resource Center CME Resources THI Journal THI Cardiac Society Save the Date: International Symposium on Cardiovascular Regenerative ...

National Space Biomedical Research Institute (NSBRI) JSC Summer Projects

NASA Technical Reports Server (NTRS)

Dowdy, Forrest Ryan

2014-01-01

This project optimized the calorie content in a breakfast meal replacement bar for the Advanced Food Technology group. Use of multivariable optimization yielded the highest weight savings possible while simultaneously matching NASA Human Standards nutritional guidelines. The scope of this research included the study of shelf-life indicators such as water activity, moisture content, and texture analysis. Key metrics indicate higher protein content, higher caloric density, and greater mass savings as a result of the reformulation process. The optimization performed for this study demonstrated wide application to other food bars in the Advanced Food Technology portfolio. Recommendations for future work include shelf life studies on bar hardening and overall acceptability data over increased time frames and temperature fluctuation scenarios.

The NES strikes a dry hole

DOE Office of Scientific and Technical Information (OSTI.GOV)

Heede, R.

1991-12-31

Thanks to widespread use of more efficient automobiles, aircraft, buildings, computers, appliances, and factories, US energy expenditures are $200 billion lower today that if the economy had remained at the level of energy productivity in 1973, and $400 billion annual energy expenditures could be trimmed in the future. However if energy saving are cheap and effective and environmentally beneficial, the question remains of why we don`t take better advantage of them. The speed of technological advances and resistance to change coupled with several varieties of political myopia explain the bulk of the slow adoption of energy savings. The central issuemore » is not technology or even cost, but sound implementation strategies and education, the focus of this article.« less

Yield Improvement and Energy Savings Uing Phosphonates as Additives in Kraft pulping

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ulrike W. Tschirner; Timothy Smith

2007-03-31

Project Objective: Develop a commercially viable modification to the Kraft process resulting in energy savings, increased yield and improved bleachability. Evaluate the feasibility of this technology across a spectrum of wood species used in North America. Develop detailed fundamental understanding of the mechanism by which phosphonates improve KAPPA number and yield. Evaluate the North American market potential for the use of phosphonates in the Kraft pulping process. Examine determinants of customer perceived value and explore organizational and operational factors influencing attitudes and behaviors. Provide an economic feasibility assessment for the supply chain, both suppliers (chemical supply companies) and buyers (Kraftmore » mills). Provide background to most effectively transfer this new technology to commercial mills.« less

Energy Efficiency in Public Buildings through Context-Aware Social Computing.

PubMed

García, Óscar; Alonso, Ricardo S; Prieto, Javier; Corchado, Juan M

2017-04-11

The challenge of promoting behavioral changes in users that leads to energy savings in public buildings has become a complex task requiring the involvement of multiple technologies. Wireless sensor networks have a great potential for the development of tools, such as serious games, that encourage acquiring good energy and healthy habits among users in the workplace. This paper presents the development of a serious game using CAFCLA, a framework that allows for integrating multiple technologies, which provide both context-awareness and social computing. Game development has shown that the data provided by sensor networks encourage users to reduce energy consumption in their workplace and that social interactions and competitiveness allow for accelerating the achievement of good results and behavioral changes that favor energy savings.

ECASTAR: Energy conservation. An assessment of systems, technologies and requirements

NASA Technical Reports Server (NTRS)

1975-01-01

A methodology was presented for a systems approach to energy conservation actions and their potentials and impacts in the United States. Constraints affecting the approach were ranked, and the most important ones are the present economic and technical conditions. The following unresolved issues were identified: consumptive lifestyles vs. conservation ethic, environmental standards vs. energy conservation, capital availability, decentralization and vertical integration vs. centralization, fuel rich regions vs. fuel poor regions, supply vs. end use conservation, life cycle costing vs. initial cost, mandatory savings vs. voluntary savings, labor intensive vs. capital intensive, price control vs. free market. The following recommendations were made: provide action/impact assessment, establish regional energy centers, improve technology articulation with government, design total energy systems, utilize existing systems approach expertise.

Technology Solutions Case Study: Excavationless: Exterior-Side Foundation Insulation for Existing Homes

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

Building science research supports installing exterior (soil side) foundation insulation as the optimal method to enhance the hygrothermal performance of new homes. With exterior foundation insulation, water management strategies are maximized while insulating the basement space and ensuring a more even temperature at the foundation wall. This project describes an innovative, minimally invasive foundation insulation upgrade technique on an existing home that uses hydrovac excavation technology combined with a liquid insulating foam. Cost savings over the traditional excavation process ranged from 23% to 50%. The excavationless process could result in even greater savings since replacement of building structures, exterior features,more » utility meters, and landscaping would be minimal or non-existent in an excavationless process.« less

Computer multitasking with Desqview 386 in a family practice.

PubMed Central

Davis, A E

1990-01-01

Computers are now widely used in medical practice for accounting and secretarial tasks. However, it has been much more difficult to use computers in more physician-related activities of daily practice. I investigated the Desqview multitasking system on a 386 computer as a solution to this problem. Physician-directed tasks of management of patient charts, retrieval of reference information, word processing, appointment scheduling and office organization were each managed by separate programs. Desqview allowed instantaneous switching back and forth between the various programs. I compared the time and cost savings and the need for physician input between Desqview 386, a 386 computer alone and an older, XT computer. Desqview significantly simplified the use of computer programs for medical information management and minimized the necessity for physician intervention. The time saved was 15 minutes per day; the costs saved were estimated to be $5000 annually. PMID:2383848

Robotics in rehabilitation: technology as destiny.

PubMed

Stein, Joel

2012-11-01

Robotic aids for rehabilitation hold considerable promise but have not yet achieved widespread clinical adoption. Barriers to adoption include the limited data on efficacy, the single-purpose design of existing robots, financial considerations, and clinician lack of familiarity with this technology. Although the path forward to clinical adoption may be slow and have several false starts, the labor-saving aspect of robotic technology will ultimately ensure its adoption.

Effect of aircraft technology improvements on intercity energy use

NASA Technical Reports Server (NTRS)

1976-01-01

An examination of the growth or decline in energy consumption in short haul, high density intercity transportation is made in relation to changes in aeronautical technology. Improvements or changes in the technology of competitive modes are also included. Certain improvements in air traffic control procedures were included to determine their effectiveness in saving energy along with a fuel efficient turboprop short haul aircraft concept.

Simulation of a Novel Single-column Cryogenic Air Separation Process Using LNG Cold Energy

NASA Astrophysics Data System (ADS)

Jieyu, Zheng; Yanzhong, Li; Guangpeng, Li; Biao, Si

In this paper, a novel single-column air separation process is proposed with the implementation of heat pump technique and introduction of LNG coldenergy. The proposed process is verifiedand optimized through simulation on the Aspen Hysys® platform. Simulation results reveal that thepower consumption per unit mass of liquid productis around 0.218 kWh/kg, and the total exergy efficiency of the systemis 0.575. According to the latest literatures, an energy saving of 39.1% is achieved compared with those using conventional double-column air separation units.The introduction of LNG cold energy is an effective way to increase the system efficiency.

Rapid, economical qualitative method for separation of aflatoxins B-1, B-2 & G-1, G-2 by dry column chromatography.

PubMed

Megalla, S E

1983-12-01

A good correlation of four components of aflatoxins was accomplished by using the dry column chromatography method. The decolorization process of interfering substances, by 0.01 N KOH and defatting the extract with petroleum ether yields a clean residue for DCC separation. It is clear that the dry column chromatography is a very simple and time-saving procedure for separation of aflatoxins. DCC columns are more economical than precoated 'thick layer' preparative plates and, in DCC, no large developing tanks need to be used. Hazards associated with the use of large volumes of flammable solvents are greatly reduced.

Multi-Year Program Plan FY'09-FY'15 Solid-State Lighting Research and Development

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

2009-03-01

President Obama's energy and environment agenda calls for deployment of 'the Cheapest, Cleanest, Fastest Energy Source - Energy Efficiency.' The Department of Energy's (DOE) Office of Energy Efficiency and Renewable Energy (EERE) plays a critical role in advancing the President's agenda by helping the United States advance toward an energy-efficient future. Lighting in the United States is projected to consume nearly 10 quads of primary energy by 2012.3 A nation-wide move toward solid-state lighting (SSL) for general illumination could save a total of 32.5 quads of primary energy between 2012 and 2027. No other lighting technology offers the DOE andmore » our nation so much potential to save energy and enhance the quality of our built environment. The DOE has set forth the following mission statement for the SSL R&D Portfolio: Guided by a Government-industry partnership, the mission is to create a new, U.S.-led market for high-efficiency, general illumination products through the advancement of semiconductor technologies, to save energy, reduce costs and enhance the quality of the lighted environment.« less

How effective is group feedback in encouraging occupants of an office building to reduce energy consumption?

NASA Astrophysics Data System (ADS)

Shah, Ushik D.

Lighting contributes to a high percentage of the total energy use in office buildings. The lack of financial incentive often dissuades office workers from trying to save electricity at their work place. This thesis aims at reducing the total power consumed by an office building by using persuasive technologies on the occupants to promote environmentally conscious and energy saving behavior. A three week field study was conducted by providing occupants of an office building feedback about their energy consumption along with messages to encourage them to save energy. Feedback was provided via television screens and flyers placed strategically at the study location, the fourth floor of the Knoy Hall of Technology, Purdue University, West Lafayette campus. The results obtained from the analysis of data showed no change in energy consumption post intervention. Group feedback thus proved to be ineffective in encouraging occupants of this office building to reduce their energy consumption. This thesis presents the findings of the study and discusses recommendations and future scope for similar studies.

Cogeneration Technology Alternatives Study (CTAS). Volume 5: Cogeneration systems results

NASA Technical Reports Server (NTRS)

Gerlaugh, H. E.; Hall, E. W.; Brown, D. H.; Priestley, R. R.; Knightly, W. F.

1980-01-01

The use of various advanced energy conversion systems is examined and compared with each other and with current technology systems for savings in fuel energy, costs, and emissions in individual plants and on a national level. About fifty industrial processes from the largest energy consuming sectors were used as a basis for matching a similar number of energy conversion systems that are considered as candidate which can be made available by the 1985 to 2000 time period. The sectors considered included food, textiles, lumber, paper, chemicals, petroleum, glass, and primary metals. The energy conversion systems included steam and gas turbines, diesels, thermionics, stirling, closed cycle and steam injected gas turbines, and fuel cells. Fuels considered were coal, both coal and petroleum based residual and distillate liquid fuels, and low Btu gas obtained through the on site gasification of coal. The methodology and results of matching the cogeneration energy conversion systems to approximately 50 industrial processes are described. Results include fuel energy saved, levelized annual energy cost saved, return on investment, and operational factors relative to the noncogeneration base cases.

Agreement Technologies for Energy Optimization at Home

PubMed Central

2018-01-01

Nowadays, it is becoming increasingly common to deploy sensors in public buildings or homes with the aim of obtaining data from the environment and taking decisions that help to save energy. Many of the current state-of-the-art systems make decisions considering solely the environmental factors that cause the consumption of energy. These systems are successful at optimizing energy consumption; however, they do not adapt to the preferences of users and their comfort. Any system that is to be used by end-users should consider factors that affect their wellbeing. Thus, this article proposes an energy-saving system, which apart from considering the environmental conditions also adapts to the preferences of inhabitants. The architecture is based on a Multi-Agent System (MAS), its agents use Agreement Technologies (AT) to perform a negotiation process between the comfort preferences of the users and the degree of optimization that the system can achieve according to these preferences. A case study was conducted in an office building, showing that the proposed system achieved average energy savings of 17.15%. PMID:29783768

Saving for Learning in the Netherlands. Research Report.

ERIC Educational Resources Information Center

Biggar, Sharon

The Netherlands has been characterized by highly differentiated secondary education, with separate practical, vocational, secondary, and pre-university institutions. Over time, these have converged somewhat. Well-thought-out vocational and adult programs emphasize providing skills needed in the workplace. At least part-time education is compulsory…

Links between global meat trade and organic river pollution

NASA Astrophysics Data System (ADS)

Wen, Yingrong; Schoups, Gerrit; van de Giesen, Nick

2017-04-01

Rising demand of meat boosts livestock farming intensification. Due to international meat trade, the environmental costs of production are becoming increasingly separated from where the meat is consumed. However, little is known about the impact of trade on the environment for both importers and exporters. Combining multi-scale (national, regional and gridded) data, we present a new method to quantify the impacts of international meat trade on global river organic pollution. We computed spatially distributed organic pollution in global river networks with and without meat trade, where the without-trade scenario assumes that meat imports are replaced by local production. Our analysis indicates high potential savings of livestock population and pollutants production at the global scale due to the international meat trade. The spatially detailed analysis shows that current trade contributes to organic pollution reductions in meat importing regions, especially in rich nations. The deterioration of river water quality, especially in developing regions, points to an urgent need for affordable infrastructure and technology development and wastewater solutions.

Photorealistic scene presentation: virtual video camera

NASA Astrophysics Data System (ADS)

Johnson, Michael J.; Rogers, Joel Clark W.

1994-07-01

This paper presents a low cost alternative for presenting photo-realistic imagery during the final approach, which often is a peak workload phase of flight. The method capitalizes on `a priori' information. It accesses out-the-window `snapshots' from a mass storage device, selecting the snapshots that deliver the best match for a given aircraft position and runway scene. It then warps the snapshots to align them more closely with the current viewpoint. The individual snapshots, stored as highly compressed images, are decompressed and interpolated to produce a `clear-day' video stream. The paper shows how this warping, when combined with other compression methods, saves considerable amounts of storage; compression factors from 1000 to 3000 were achieved. Thus, a CD-ROM today can store reference snapshots for thousands of different runways. Dynamic scene elements not present in the snapshot database can be inserted as separate symbolic or pictorial images. When underpinned by an appropriate suite of sensor technologies, the methods discussed indicate an all-weather virtual video camera is possible.

Reversed-Phase High-Performance Liquid Chromatography for the Quantification and Optimization for Extracting 10 Kinds of Carotenoids in Pepper (Capsicum annuum L.) Leaves.

PubMed

Li, Jing; Xie, Jianming; Yu, Jihua; Lv, Jian; Zhang, Junfeng; Wang, Xiaolong; Wang, Cheng; Tang, Chaonan; Zhang, Yingchun; Dawuda, Mohammed Mujitaba; Zhu, Daiqiang; Ma, Guoli

2017-09-27

Carotenoids are considered to be crucial elements in many fields and, furthermore, the significant factor in pepper leaves under low light and chilling temperature. However, little literature focused on the method to determinate and extract the contents of carotenoid compositions in pepper leaves. Therefore, a time-saving and highly sensitive reversed-phase high-performance liquid chromatography method for separation and quantification of 10 carotenoids was developed, and an optimized technological process for carotenoid composition extraction in pepper leaves was established for the first time. Our final method concluded that six xanthophylls eluted after about 9-26 min. In contrast, four carotenes showed higher retention times after nearly 28-40 min, which significantly shortened time and improved efficiency. Meanwhile, we suggested that 8 mL of 20% KOH-methanol solution should be added to perform saponification at 60 °C for 30 min. The ratio of solid-liquid was 1:8, and the ultrasound-assisted extraction time was 40 min.

Next generation industrial biotechnology based on extremophilic bacteria.

PubMed

Chen, Guo-Qiang; Jiang, Xiao-Ran

2018-04-01

Industrial biotechnology aims to produce bulk chemicals including polymeric materials and biofuels based on bioprocessing sustainable agriculture products such as starch, fatty acids and/or cellulose. However, traditional bioprocesses require bioreactors made of stainless steel, complicated sterilization, difficult and expensive separation procedures as well as well-trained engineers that are able to conduct bioprocessing under sterile conditions, reducing the competitiveness of the bio-products. Amid the continuous low petroleum price, next generation industrial biotechnology (NGIB) allows bioprocessing to be conducted under unsterile (open) conditions using ceramic, cement or plastic bioreactors in a continuous way, it should be an energy, water and substrate saving technology with convenient operation procedure. NGIB also requires less capital investment and reduces demand on highly trained engineers. The foundation for the simplified NGIB is microorganisms that resist contaminations by other microbes, one of the examples is rapid growing halophilic bacteria inoculated under high salt concentration and alkali pH. They have been engineered to produce multiple products in various scales. Copyright © 2017 Elsevier Ltd. All rights reserved.

Recycling the liquid fraction of alkaline hydrogen peroxide in the pretreatment of corn stover.

PubMed

Alencar, Bárbara Ribeiro Alves; Reis, Alexandre Libanio Silva; de Souza, Raquel de Fatima Rodrigues; Morais, Marcos Antônio; Menezes, Rômulo Simões Cezar; Dutra, Emmanuel Damilano

2017-10-01

The aim of this study was to evaluate the influence of recycling the liquid fraction of pretreatment with alkaline hydrogen peroxide (AHP) on the hydrolysis of corn stover. Corn stover was pretreated in the traditional condition with 7.5% v/v H 2 O 2 . After pretreatment, the solids were separated from the liquid fraction and five successive reuse cycles of the liquid fraction were tested. The solid fraction from pretreatment in each recycle was submitted to enzymatic hydrolysis. The number of recycles had a linear negative effect (R 2 =0.98) on biomass delignification efficiency and also affected negatively the enzymatic conversion efficiency. Despite the decrease in efficiency after each recycling step, reuse of the liquid fraction leads to reduction in water, H 2 O 2 and NaOH consumption of up to 57.6%, 59.6% and 57.6%, respectively. These findings point to an efficient recycling technology, which may reduce costs and save water. Copyright © 2017 Elsevier Ltd. All rights reserved.

Experimental Evaluation of High Performance Integrated Heat Pump

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miller, William A; Berry, Robert; Durfee, Neal

2016-01-01

Integrated heat pump (IHP) technology provides significant potential for energy savings and comfort improvement for residential buildings. In this study, we evaluate the performance of a high performance IHP that provides space heating, cooling, and water heating services. Experiments were conducted according to the ASHRAE Standard 206-2013 where 24 test conditions were identified in order to evaluate the IHP performance indices based on the airside performance. Empirical curve fits of the unit s compressor maps are used in conjunction with saturated condensing and evaporating refrigerant conditions to deduce the refrigerant mass flowrate, which, in turn was used to evaluate themore » refrigerant side performance as a check on the airside performance. Heat pump (compressor, fans, and controls) and water pump power were measured separately per requirements of Standard 206. The system was charged per the system manufacturer s specifications. System test results are presented for each operating mode. The overall IHP performance metrics are determined from the test results per the Standard 206 calculation procedures.« less

Robust and durable superhydrophobic cotton fabrics for oil/water separation.

PubMed

Zhou, Xiaoyan; Zhang, Zhaozhu; Xu, Xianghui; Guo, Fang; Zhu, Xiaotao; Men, Xuehu; Ge, Bo

2013-08-14

By introducing the incorporation of polyaniline and fluorinated alkyl silane to the cotton fabric via a facile vapor phase deposition process, the fabric surface possessed superhydrophobicity with the water contact angle of 156° and superoleophilicity with the oil contact angle of 0°. The as-prepared fabric can be applied as effective materials for the separation of water and oil mixture with separation efficiency as high as 97.8%. Compared with other materials for oil/water separation, the reported process was simple, time-saving, and repeatable for at least 30 times. Moreover, the obtained fabric kept stable superhydrophobicity and high separation efficiency under extreme environment conditions of high temperature, high humidity, strong acidic or alkaline solutions, and mechanical forces. Therefore, this reported fabric has the advantages of scalable fabrication, high separation efficiency, stable recyclability, and excellent durability, exhibiting the strong potential for industrial production.

Heart Information Center

MedlinePlus

... Daily Conferences Fellowships and Residencies School of Perfusion Technology Education Resources Library & Learning Resource Center CME Resources THI Journal THI Cardiac Society Save the Date: International Symposium on Cardiovascular Regenerative ...

Mitral Valve Prolapse

MedlinePlus

... Daily Conferences Fellowships and Residencies School of Perfusion Technology Education Resources Library & Learning Resource Center CME Resources THI Journal THI Cardiac Society Save the Date: International Symposium on Cardiovascular Regenerative ...

Transmyocardial Laser Revascularization

MedlinePlus

... Daily Conferences Fellowships and Residencies School of Perfusion Technology Education Resources Library & Learning Resource Center CME Resources THI Journal THI Cardiac Society Save the Date: International Symposium on Cardiovascular Regenerative ...

Coronary Artery Anomalies

MedlinePlus

... Daily Conferences Fellowships and Residencies School of Perfusion Technology Education Resources Library & Learning Resource Center CME Resources THI Journal THI Cardiac Society Save the Date: International Symposium on Cardiovascular Regenerative ...

Application of Waste Heat Recovery Energy Saving Technology in Reform of UHP-EAF

NASA Astrophysics Data System (ADS)

Zhao, J. H.; Zhang, S. X.; Yang, W.; Yu, T.

2017-08-01

The furnace waste heat of a company’s existing 4 × 100t ultra-high-power electric arc furnaces is not used and discharged directly of the situation has been unable to meet the national energy-saving emission reduction requirements, and also affected their own competitiveness and sustainable development. In order to make full use of the waste heat of the electric arc furnace, this paper presents an the energy-saving transformation program of using the new heat pipe boiler on the existing ultra-high-power electric arc furnaces for recovering the waste heat of flue gas. The results show that after the implementation of the project can save energy equivalent to 42,349 tons of standard coal. The flue gas waste heat is fully utilized and dust emission concentration is accorded with the standard of Chinese invironmental protection, which have achieved good results.

Red blood cell depletion from bone marrow and peripheral blood buffy coat: a comparison of two new and three established technologies.

PubMed

Sorg, Nadine; Poppe, Carolin; Bunos, Milica; Wingenfeld, Eva; Hümmer, Christiane; Krämer, Ariane; Stock, Belinda; Seifried, Erhard; Bonig, Halvard

2015-06-01

Red blood cell (RBC) depletion is a standard technique for preparation of ABO-incompatible bone marrow transplants (BMTs). Density centrifugation or apheresis are used successfully at clinical scale. The advent of a bone marrow (BM) processing module for the Spectra Optia (Terumo BCT) provided the initiative to formally compare our standard technology, the COBE2991 (Ficoll, manual, "C") with the Spectra Optia BMP (apheresis, semiautomatic, "O"), the Sepax II NeatCell (Ficoll, automatic, "S"), the Miltenyi CliniMACS Prodigy density gradient separation system (Ficoll, automatic, "P"), and manual Ficoll ("M"). C and O handle larger product volumes than S, P, and M. Technologies were assessed for RBC depletion, target cell (mononuclear cells [MNCs] for buffy coats [BCs], CD34+ cells for BM) recovery, and cost/labor. BC pools were simultaneously purged with C, O, S, and P; five to 18 BM samples were sequentially processed with C, O, S, and M. Mean RBC removal with C was 97% (BCs) or 92% (BM). From both products, O removed 97%, and P, S, and M removed 99% of RBCs. MNC recovery from BC (98% C, 97% O, 65% P, 74% S) or CD34+ cell recovery from BM (92% C, 90% O, 67% S, 70% M) were best with C and O. Polymorphonuclear cells (PMNs) were depleted from BCs by P, S, and C, while O recovered 50% of PMNs. Time savings compared to C or M for all tested technologies are considerable. All methods are in principle suitable and can be selected based on sample volume, available technology, and desired product specifications beyond RBC depletion and MNC and/or CD34+ cell recovery. © 2015 AABB.

Application of BIM technology in construction bidding

NASA Astrophysics Data System (ADS)

wei, Li

2017-12-01

bidding is a very important step of construction project. For the owners, bidding is the key link of selecting the best construction plan and saving the project cost to the maximum extent. For Construction Corporation, it is the key to show their construction technology which can improve the probability of winning the bid. this paper researches on the application of BIM technology in bidding process of construction project in detail, and discussesthe application of BIM technology in construction field comprehensively.

Cost modeling to justify technology acquisitions.

PubMed

Vanden Brink, J; Gray, S

1997-06-01

In an era of diminishing resources, healthcare providers must justify new technology acquisitions. Cost modeling is one method of evaluating the financial impact a technology acquisition will have on a healthcare facility or integrated delivery system. This methodology requires careful data collection and a thorough analysis of both current costs and future cost savings resulting from the new technology. By using a cost modeling methodology, providers will be able to achieve competitive and economic advantages by analyzing both cost and value.

Innovative production technology ethanol from sweet sorghum

NASA Astrophysics Data System (ADS)

Kashapov, N. F.; Nafikov, M. M.; Gazetdinov, M. X.; Nafikova, M. M.; Nigmatzyanov, A. R.

2016-06-01

The paper considers the technological aspects of production of ethanol from nontraditional for Russian Federation crops - sweet sorghum. Presents the technological scheme of alcohol production and fuel pellets from sweet sorghum. Special attention is paid to assessing the efficiency of alcohol production from sweet sorghum. The described advantage of sugar content in stem juice of sweet sorghum compared with other raw materials. Allegedly, the use of the technology for producing alcohol from sweet sorghum allows to save resources.

Distributive Distillation Enabled by Microchannel Process Technology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Arora, Ravi

The application of microchannel technology for distributive distillation was studied to achieve the Grand Challenge goals of 25% energy savings and 10% return on investment. In Task 1, a detailed study was conducted and two distillation systems were identified that would meet the Grand Challenge goals if the microchannel distillation technology was used. Material and heat balance calculations were performed to develop process flow sheet designs for the two distillation systems in Task 2. The process designs were focused on two methods of integrating the microchannel technology 1) Integrating microchannel distillation to an existing conventional column, 2) Microchannel distillation formore » new plants. A design concept for a modular microchannel distillation unit was developed in Task 3. In Task 4, Ultrasonic Additive Machining (UAM) was evaluated as a manufacturing method for microchannel distillation units. However, it was found that a significant development work would be required to develop process parameters to use UAM for commercial distillation manufacturing. Two alternate manufacturing methods were explored. Both manufacturing approaches were experimentally tested to confirm their validity. The conceptual design of the microchannel distillation unit (Task 3) was combined with the manufacturing methods developed in Task 4 and flowsheet designs in Task 2 to estimate the cost of the microchannel distillation unit and this was compared to a conventional distillation column. The best results were for a methanol-water separation unit for the use in a biodiesel facility. For this application microchannel distillation was found to be more cost effective than conventional system and capable of meeting the DOE Grand Challenge performance requirements.« less

Future Warfare: Anthology Revised Edition

DTIC Science & Technology

2001-06-01

film “ Saving Private Ryan ” are compelling and chilling. But the information age promises to make ground combat considerably less destructive that the...116 Saving Private Ryan , 80–81 Schwarzkopf, Norman, 242, 243–244 Science and technology, 191–202 Scipio, 44 Security beyond the year 2010, 128–131, 137... Private Ryan ” where the true horror of face-to-face ground combat is driven into the psyche of the movie goer. I am increasingly convinced, however

Commercial Mobile Device Technology Implementation Implications in United States Marine Corps Processes: A Case Study Approach

DTIC Science & Technology

2016-09-01

innovative solutions to current problems. One such innovation that could potentially save the Marine Corps money , while increasing its ability to prepare...the Marine Corps money , while increasing its ability to prepare for and conduct its mission, is the use of commercial mobile devices. This research...problems. One such innovation that could potentially save the USMC money , while increasing the ability to prepare for and conduct its mission is the

Energy and emissions saving potential of additive manufacturing: the case of lightweight aircraft components

DOE Office of Scientific and Technical Information (OSTI.GOV)

Huang, Runze; Riddle, Matthew; Graziano, Diane

Additive manufacturing (AM) holds great potential for improving materials efficiency, reducing life-cycle impacts, and enabling greater engineering functionality compared to conventional manufacturing (CM), and AM has been increasingly adopted by aircraft component manufacturers for lightweight, cost-effective designs. This study estimates the net changes in life-cycle primary energy and greenhouse gas emissions associated with AM technologies for lightweight metallic aircraft components through the year 2050, to shed light on the environmental benefits of a shift from CM to AM processes in the U.S. aircraft industry. A systems modeling framework is presented, with integrates engineering criteria, life-cycle environmental data, aircraft fleet stockmore » and fuel use models under different AM adoption scenarios. Estimated fleet-wide life-cycle primary energy savings at most reach 70-173 million GJ/year in 2050, with cumulative savings of 1.2–2.8 billion GJ. Associated cumulative GHG emission reductions were estimated at 92.1–215.0 million metric tons. In addition, thousands of tons of aluminum, titanium and nickel alloys could be potentially saved per year in 2050. The results indicate a significant role of AM technologies in helping society meet its long-term energy use and GHG emissions reduction goals, and highlight barriers and opportunities for AM adoption for the aircraft industry.« less

Low Cost Chemical Feedstocks Using an Improved and Energy Efficient Natural Gas Liquid (NGL) Removal Process, Final Technical Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Meyer, Howard, S.; Lu, Yingzhong

The overall objective of this project is to develop a new low-cost and energy efficient Natural Gas Liquid (NGL) recovery process - through a combination of theoretical, bench-scale and pilot-scale testing - so that it could be offered to the natural gas industry for commercialization. The new process, known as the IROA process, is based on U.S. patent No. 6,553,784, which if commercialized, has the potential of achieving substantial energy savings compared to currently used cryogenic technology. When successfully developed, this technology will benefit the petrochemical industry, which uses NGL as feedstocks, and will also benefit other chemical industries thatmore » utilize gas-liquid separation and distillation under similar operating conditions. Specific goals and objectives of the overall program include: (i) collecting relevant physical property and Vapor Liquid Equilibrium (VLE) data for the design and evaluation of the new technology, (ii) solving critical R&D issues including the identification of suitable dehydration and NGL absorbing solvents, inhibiting corrosion, and specifying proper packing structure and materials, (iii) designing, construction and operation of bench and pilot-scale units to verify design performance, (iv) computer simulation of the process using commercial software simulation platforms such as Aspen-Plus and HYSYS, and (v) preparation of a commercialization plan and identification of industrial partners that are interested in utilizing the new technology. NGL is a collective term for C2+ hydrocarbons present in the natural gas. Historically, the commercial value of the separated NGL components has been greater than the thermal value of these liquids in the gas. The revenue derived from extracting NGLs is crucial to ensuring the overall profitability of the domestic natural gas production industry and therefore of ensuring a secure and reliable supply in the 48 contiguous states. However, rising natural gas prices have dramatically reduced the economic incentive to extract NGLs from domestically produced natural gas. Successful gas processors will be those who adopt technologies that are less energy intensive, have lower capital and operating costs and offer the flexibility to tailor the plant performance to maximize product revenue as market conditions change, while maintaining overall system efficiency. Presently, cryogenic turbo-expander technology is the dominant NGL recovery process and it is used throughout the world. This process is known to be highly energy intensive, as substantial energy is required to recompress the processed gas back to pipeline pressure. The purpose of this project is to develop a new NGL separation process that is flexible in terms of ethane rejection and can reduce energy consumption by 20-30% from current levels, particularly for ethane recoveries of less than 70%. The new process integrates the dehydration of the raw natural gas stream and the removal of NGLs in such a way that heat recovery is maximized and pressure losses are minimized so that high-value equipment such as the compressor, turbo-expander, and a separate dehydration unit are not required. GTI completed a techno-economic evaluation of the new process based on an Aspen-HYSYS simulation model. The evaluation incorporated purchased equipment cost estimates obtained from equipment suppliers and two different commercial software packages; namely, Aspen-Icarus and Preliminary Design and Quoting Service (PDQ$). For a 100 MMscfd gas processing plant, the annualized capital cost for the new technology was found to be about 10% lower than that of conventional technology for C2 recovery above 70% and about 40% lower than that of conventional technology for C2 recovery below 50%. It was also found that at around 40-50% C2 recovery (which is economically justifiable at the current natural gas prices), the energy cost to recover NGL using the new technology is about 50% of that of conventional cryogenic technology.« less

Membrane separation systems---A research and development needs assessment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baker, R.W.; Cussler, E.L.; Eykamp, W.

1990-04-01

Industrial separation processes consume a significant portion of the energy used in the United States. A 1986 survey by the Office of Industrial Programs estimated that about 4.2 quads of energy are expended annually on distillation, drying and evaporation operations. This survey also concluded that over 0.8 quads of energy could be saved in the chemical, petroleum and food industries alone if these industries adopted membrane separation systems more widely. Membrane separation systems offer significant advantages over existing separation processes. In addition to consuming less energy than conventional processes, membrane systems are compact and modular, enabling easy retrofit to existingmore » industrial processes. The present study was commissioned by the Department of Energy, Office of Program Analysis, to identify and prioritize membrane research needs in light of DOE's mission. Each report will be individually cataloged.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kobos, Peter Holmes; Malczynski, Leonard A.; Walker, La Tonya Nicole

People save for retirement throughout their career because it is virtually impossible to save all you’ll need in retirement the year before you retire. Similarly, without installing incremental amounts of clean fossil, renewable or transformative energy technologies throughout the coming decades, a radical and immediate change will be near impossible the year before a policy goal is set to be in place. This notion of steady installation growth over acute installations of technology to meet policy goals is the core topic of discussion for this research. This research operationalizes this notion by developing the theoretical underpinnings of regulatory and marketmore » acceptance delays by building upon the common Technology Readiness Level (TRL) framework and offers two new additions to the research community. The new and novel Regulatory Readiness Level (RRL) and Market Readiness Level (MRL) frameworks were developed. These components, collectively called the Technology, Regulatory and Market (TRM) readiness level framework allow one to build new constraints into existing Integrated Assessment Models (IAMs) to address research questions such as, ‘To meet our desired technical and policy goals, what are the factors that affect the rate we must install technology to achieve these goals in the coming decades?’« less

Fresh Veggies from Space

NASA Technical Reports Server (NTRS)

2001-01-01

Professor Marc Anderson of the University of Wisconsin-Madison developed a technology for use in plant-growth experiments aboard the Space Shuttle. Anderson's research and WCSAR's technology were funded by NASA and resulted in a joint technology licensed to KES Science and Technology, Inc. This transfer of space-age technology resulted in the creation of a new plant-saving product, an ethylene scrubber for plant growth chambers. This innovation presents commercial benefits for the food industry in the form of a new device, named Bio-KES. Bio-KES removes ethylene and helps to prevent spoilage. Ethylene accounts for up to 10 percent of produce losses and 5 percent of flower losses. Using Bio-KES in storage rooms and displays will increase the shelf life of perishable foods by more than one week, drastically reducing the costs associated with discarded rotten foods and flowers. The savings could potentially be passed on to consumers. For NASA, the device means that astronauts can conduct commercial agricultural research in space. Eventually, it may also help to grow food in space and keep it fresh longer. This could lead to less packaged food being taken aboard missions since it could be cultivated in an ethylene-free environment.

Diagnostic Tests and Procedures

MedlinePlus

... Daily Conferences Fellowships and Residencies School of Perfusion Technology Education Resources Library & Learning Resource Center CME Resources THI Journal THI Cardiac Society Save the Date: International Symposium on Cardiovascular Regenerative ...

Vasculature of the Leg

MedlinePlus

... Daily Conferences Fellowships and Residencies School of Perfusion Technology Education Resources Library & Learning Resource Center CME Resources THI Journal THI Cardiac Society Save the Date: International Symposium on Cardiovascular Regenerative ...

Cost-Value Analysis and the SAVE: A Work in Progress, But an Option for Localised Decision Making?

PubMed

Karnon, Jonathan; Partington, Andrew

2015-12-01

Cost-value analysis aims to address the limitations of the quality-adjusted life-year (QALY) by incorporating the strength of public concerns for fairness in the allocation of scarce health care resources. To date, the measurement of value has focused on equity weights to reflect societal preferences for the allocation of QALY gains. Another approach is to use a non-QALY-based measure of value, such as an outcome 'equivalent to saving the life of a young person' (a SAVE). This paper assesses the feasibility and validity of using the SAVE as a measure of value for the economic evaluation of health care technologies. A web-based person trade-off (PTO) survey was designed and implemented to estimate equivalent SAVEs for outcome events associated with the progression and treatment of early-stage breast cancer. The estimated equivalent SAVEs were applied to the outputs of an existing decision analytic model for early breast cancer. The web-based PTO survey was undertaken by 1094 respondents. Validation tests showed that 68 % of eligible responses revealed consistent ordering of responses and 32 % displayed ordinal transitivity, while 37 % of respondents showing consistency and ordinal transitivity approached cardinal transitivity. Using consistent and ordinally transitive responses, the mean incremental cost per SAVE gained was £ 3.72 million. Further research is required to improve the validity of the SAVE, which may include a simpler web-based survey format or a face-to-face format to facilitate more informed responses. A validated method for estimating equivalent SAVEs is unlikely to replace the QALY as the globally preferred measure of outcome, but the SAVE may provide a useful alternative for localized decision makers with relatively small, constrained budgets-for example, in programme budgeting and marginal analysis.

A SIEPON based transmitter sleep mode energy-efficient mechanism in EPON

NASA Astrophysics Data System (ADS)

Nikoukar, AliAkbar; Hwang, I.-Shyan; Wang, Chien-Jung; Ab-Rahman, Mohammad Syuhaimi; Liem, Andrew Tanny

2015-06-01

The main energy consumption in computer networks is the access networks. The passive optical network (PON) has the least energy consumption among access network technologies. In addition, the time division multiplexing (TDM) Ethernet PON (EPON) is one of the best candidates to improve energy consumption by time utilization. The optical network unit (ONU) can utilize the time and save the energy in the EPON by turning off its transmitter/receiver when there is no upstream/downstream traffic. The ITU-T and IEEE organizations are published standards for energy-saving in the TDM-PON. Although their standards provide the framework to accomplish the energy-saving, the algorithms/criteria to generate events to accommodate various operational policies, time to wake up, parameter values for timers are out of scope of the standards. Many studies have proposed schemes for energy-saving in TDM-PON to achieve maximum energy saving. Even so, these schemes increase the mean packet delay and consequently, reduce the quality of service (QoS). In this paper, first we take a look to the state of the art for PON energy-saving. Additionally, a mechanism based on SIEPON standard in EPON with new components in the ONUs and optical line terminal (OLT) is proposed to save the transmitter energy and guarantee QoS. The proposed mechanism follows the SIEPON standard, considers the QoS first, and then saves the energy as far as possible. The ONU sleep controller unit (OSC) and green dynamic bandwidth allocation (GDBA) are used to calculate the ONU transmitter sleep (Tx) duration and grant the proper time to the ONUs. Simulation results show that the proposed energy-saving mechanism not only promises the QoS performance in terms of mean packet delay, packet loss, throughput, and jitter, but also saves energy in different maximum cycle times.

Separation and Depleted Uranium Fragments from Gun Test Catchment. Volume 2. Catchment System and Separations Methods

DTIC Science & Technology

1993-12-30

projectile fragments from target materials, principally sand. Phase I activities included (1) literature review of separations technology , (2) site visits, (3...the current operation, evaluation of alternative means for separation of DU from sand, a review of uranium mining technology for v possible...the current operation, evaluation of alternative means for separation of DU from sand, a review of uranium mining technology for possible

Alcoa North American Extrusions Implements Energy Use Assessments at Multiple Facilities: Office of Industrial Technologies (OIT) BestPractices Aluminum Assessment Case Study

DOE Office of Scientific and Technical Information (OSTI.GOV)

U.S. Department of Energy

2001-08-05

This case study is the latest in a series on industrial firms who are implementing energy efficient technologies and system improvements into their manufacturing processes. The case studies document the activities, savings, and lessons learned on these projects.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ramachandran, N.

New technologies were used to cost-effectively remediate several hundred feet of radioactively contaminated subsurface drain pipes at the General Motors site in Adrian, Michigan, and to conduct post-remedial verification surveys. Supplemental cleanup criteria were applied to inaccessible areas of the project, and inexpensive treatment technology was used to treat wastewater generated. Application of these methods resulted in substantial cost savings.

Complex modeling of technological processes in pneumatic mixers for production of dry construction mixtures

NASA Astrophysics Data System (ADS)

Orekhova, T. N.; Nosov, O. A.; Prokopenko, V. S.; Kachaev, A. E.

2018-03-01

The improvement of the design of the pneumatic mixers aimed at the possibility of obtaining homogeneous disperse systems, while the resource and energy saving issues play an important role in the conditions of enterprises that use this type of equipment in their technological chain, is described in the article.

Using iPods in Dance Pedagogy

ERIC Educational Resources Information Center

Block, Betty A.

2008-01-01

Today's "Net Generation" is used to instant access to information that is wireless and mobile. There is so much information that students can access on their own that class time can be saved for things technology cannot teach, such as personal interactions, dance etiquette, and partnering. Technology should not be a substitute for personal and…

Waste-to-Chemicals for a Circular Economy: The Case of Urea Production (Waste-to-Urea).

PubMed

Antonetti, Elena; Iaquaniello, Gaetano; Salladini, Annarita; Spadaccini, Luca; Perathoner, Siglinda; Centi, Gabriele

2017-03-09

The economics and environmental impact of a new technology for the production of urea from municipal solid waste, particularly the residue-derived fuel (RdF) fraction, is analyzed. Estimates indicate a cost of production of approximately €135 per ton of urea (internal rate of return more than 10 %) and savings of approximately 0.113 tons of CH 4 and approximately 0.78 tons of CO 2 per ton of urea produced. Thus, the results show that this waste-to-urea (WtU) technology is both economically valuable and environmentally advantageous (in terms of saving resources and limiting carbon footprint) for the production of chemicals from municipal solid waste in comparison with both the production of urea with conventional technology (starting from natural gas) and the use of RdF to produce electrical energy (waste-to-energy). A further benefit is the lower environmental impact of the solid residue produced from RdF conversion. The further benefit of this technology is the possibility to realize distributed fertilizer production. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

A study of the cost-effective markets for new technology agricultural aircraft

NASA Technical Reports Server (NTRS)

Hazelrigg, G. A., Jr.; Clyne, F.

1979-01-01

A previously developed data base was used to estimate the regional and total U.S. cost-effective markets for a new technology agricultural aircraft as incorporating features which could result from NASA-sponsored aerial applications research. The results show that the long-term market penetration of a new technology aircraft would be near 3,000 aircraft. This market penetration would be attained in approximately 20 years. Annual sales would be about 200 aircraft after 5 to 6 years of introduction. The net present value of cost savings benefit which this aircraft would yield (measured on an infinite horizon basis) would be about $35 million counted at a 10 percent discount rate and $120 million at a 5 percent discount rate. At both discount rates the present value of cost savings exceeds the present value of research and development (R&D) costs estimated for the development of the technology base needed for the proposed aircraft. These results are quite conservative as they have been derived neglecting future growth in the agricultural aviation industry, which has been averaging about 12 percent per year over the past several years.

Economical and Energy Efficiency of Iron and Steel Industry Reindustrialisation in Russia Based on Implementation of Breakthrough Energy-Saving Technologies

NASA Astrophysics Data System (ADS)

Shevelev, L. N.

2017-12-01

Estimates were given of economical and energy efficiency of breakthrough energy-saving technologies, which increase competitive advantages and provide energy efficiency of production while reducing negative impact on the environment through reduction of emissions of harmful substances and greenhouse gases in the atmosphere. Among these technologies, preference is given to the following: pulverized coal fuel, blast-furnace gas recycling, gasification of non-coking coal in bubble-type gas-generators, iron-ore concentrate briquetting with steam coal with further use of ore-coal briquettes in electric furnace steel making. Implementation of these technologies at iron and steel works will significantly reduce the energy intensity of production through reduction of expensive coking coal consumption by means of their substitution by less expensive non-coking (steam) coal, and natural gas substitution by own secondary energy resource, which is the reducing gas. As the result, plants will get an opportunity to become self-sufficient in energy-resources and free themselves entirely from expensive purchased energy resources (natural gas, electric power, and partially coking coals), and cross over to low-carbon development.

Potentially avoidable hospitalisation for constipation in Victoria, Australia in 2010-11.

PubMed

Ansari, Humaira; Ansari, Zahid; Hutson, John M; Southwell, Bridget R

2014-07-11

When primary care of constipation fails, the patient may need emergency hospitalisation for disimpaction. This study aimed to provide population-based data on the number of unplanned admissions and the cost to the healthcare system for constipation in Victoria, Australia in financial year 2010-11. The Victorian Admitted Episodes Dataset was examined to find the number of emergency hospital separations coded as constipation (ICD-10-AM Code K390). An estimate of costs was determined from the number of weighted inlier equivalent separations (WIES) multiplied by the WEIS price, used by the Victorian Government for funding purposes. There were 3978 emergency separations for constipation in Victoria in 2010-2011, 92% in public hospitals. Fifty-five percent were female and 38% > 75 years old. One third stayed overnight and 1/3 more than 1 day. The emergency bed day rate was 7.1 per 10,000 of population. The estimate of cost, based on WEIS, was approximately $8.3 million. Potential savings could be made by reducing the number of separations in 6 Local Government Areas (LGAs). This study shows that the burden (in number of admissions, emergency bed days and overall direct costs) in managing emergency admissions for constipation in Victoria, Australia, is very significant and likely to be similar in other developed countries. Improved primary healthcare and alternative ways to achieve faecal disimpaction without emergency admission could save the public health system a proportion of this $8.3 million.

A low-power current-reuse dual-band analog front-end for multi-channel neural signal recording.

PubMed

Sepehrian, H; Gosselin, B

2014-01-01

Thoroughly studying the brain activity of freely moving subjects requires miniature data acquisition systems to measure and wirelessly transmit neural signals in real time. In this application, it is mandatory to simultaneously record the bioelectrical activity of a large number of neurons to gain a better knowledge of brain functions. However, due to limitations in transferring the entire raw data to a remote base station, employing dedicated data reduction techniques to extract the relevant part of neural signals is critical to decrease the amount of data to transfer. In this work, we present a new dual-band neural amplifier to separate the neuronal spike signals (SPK) and the local field potential (LFP) simultaneously in the analog domain, immediately after the pre-amplification stage. By separating these two bands right after the pre-amplification stage, it is possible to process LFP and SPK separately. As a result, the required dynamic range of the entire channel, which is determined by the signal-to-noise ratio of the SPK signal of larger bandwidth, can be relaxed. In this design, a new current-reuse low-power low-noise amplifier and a new dual-band filter that separates SPK and LFP while saving capacitors and pseudo resistors. A four-channel dual-band (SPK, LFP) analog front-end capable of simultaneously separating SPK and LFP is implemented in a TSMC 0.18 μm technology. Simulation results present a total power consumption per channel of 3.1 μw for an input referred noise of 3.28 μV and a NEF for 2.07. The cutoff frequency of the LFP band is fc=280 Hz, and fL=725 Hz and fL=11.2 KHz for SPK, with 36 dB gain for LFP band 46 dB gain for SPK band.

Impact of Sustainable Cool Roof Technology on Building Energy Consumption

NASA Astrophysics Data System (ADS)

Vuppuluri, Prem Kiran

Highly reflective roofing systems have been analyzed over several decades to evaluate their ability to meet sustainability goals, including reducing building energy consumption and mitigating the urban heat island. Studies have isolated and evaluated the effects of climate, surface reflectivity, and roof insulation on energy savings, thermal load mitigation and also ameliorating the urban heat island. Other sustainable roofing systems, like green-roofs and solar panels have been similarly evaluated. The motivation for the present study is twofold: the first goal is to present a method for simultaneous evaluation and inter-comparison of multiple roofing systems, and the second goal is to quantitatively evaluate the realized heating and cooling energy savings associated with a white roof system compared to the reduction in roof-top heat flux. To address the first research goal a field experiment was conducted at the International Harvester Building located in Portland, OR. Thermal data was collected for a white roof, vegetated roof, and a solar panel shaded vegetated roof, and the heat flux through these roofing systems was compared against a control patch of conventional dark roof membrane. The second research goal was accomplished using a building energy simulation program to determine the impact of roof area and roof insulation on the savings from a white roof, in both Portland and Phoenix. The ratio of cooling energy savings to roof heat flux reduction from replacing a dark roof with a white roof was 1:4 for the month of July, and 1:5 annually in Portland. The COP of the associated chillers ranges from 2.8-4.2, indicating that the ratio of cooling energy savings to heat flux reduction is not accounted for solely by the COP of the chillers. The results of the building simulation indicate that based on energy savings alone, white roofs are not an optimal choice for Portland. The benefits associated with cooling energy savings relative to a black roof are offset by the winter-time penalty, and the net benefit from adopting white roof technology in Portland is small. That said, there are other potential benefits of white roofing such as impact on urban heat islands and roof life that must also be considered.

24 CFR 904.111 - Nonroutine Maintenance Reserve (NRMR).

Code of Federal Regulations, 2014 CFR

2014-04-01

... reserve requirements for 90 days the LHA shall invest the excess in federally insured savings accounts... Nonroutine Maintenance Reserve (NRMR). (a) Purpose of reserve. The LHA shall establish and maintain a separate NRMR for each home, using a portion of the homebuyer's monthly payment. The purpose of the NRMR is...

24 CFR 904.111 - Nonroutine Maintenance Reserve (NRMR).

Code of Federal Regulations, 2013 CFR

2013-04-01

... reserve requirements for 90 days the LHA shall invest the excess in federally insured savings accounts... Nonroutine Maintenance Reserve (NRMR). (a) Purpose of reserve. The LHA shall establish and maintain a separate NRMR for each home, using a portion of the homebuyer's monthly payment. The purpose of the NRMR is...

24 CFR 904.111 - Nonroutine Maintenance Reserve (NRMR).

Code of Federal Regulations, 2011 CFR

2011-04-01

... reserve requirements for 90 days the LHA shall invest the excess in federally insured savings accounts... Nonroutine Maintenance Reserve (NRMR). (a) Purpose of reserve. The LHA shall establish and maintain a separate NRMR for each home, using a portion of the homebuyer's monthly payment. The purpose of the NRMR is...

24 CFR 904.111 - Nonroutine Maintenance Reserve (NRMR).

Code of Federal Regulations, 2012 CFR

2012-04-01

... reserve requirements for 90 days the LHA shall invest the excess in federally insured savings accounts... Nonroutine Maintenance Reserve (NRMR). (a) Purpose of reserve. The LHA shall establish and maintain a separate NRMR for each home, using a portion of the homebuyer's monthly payment. The purpose of the NRMR is...

5 CFR 1650.31 - Age-based withdrawals.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 5 Administrative Personnel 3 2012-01-01 2012-01-01 false Age-based withdrawals. 1650.31 Section... FUNDS FROM THE THRIFT SAVINGS PLAN In-Service Withdrawals § 1650.31 Age-based withdrawals. (a) A participant who has reached age 591/2 and who has not separated from Government employment is eligible to...

5 CFR 1650.31 - Age-based withdrawals.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 5 Administrative Personnel 3 2010-01-01 2010-01-01 false Age-based withdrawals. 1650.31 Section... FUNDS FROM THE THRIFT SAVINGS PLAN In-Service Withdrawals § 1650.31 Age-based withdrawals. (a) A participant who has reached age 591/2 and who has not separated from Government employment is eligible to...

5 CFR 1650.31 - Age-based withdrawals.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 5 Administrative Personnel 3 2013-01-01 2013-01-01 false Age-based withdrawals. 1650.31 Section... FUNDS FROM THE THRIFT SAVINGS PLAN In-Service Withdrawals § 1650.31 Age-based withdrawals. (a) A participant who has reached age 591/2 and who has not separated from Government service is eligible to...

5 CFR 1650.31 - Age-based withdrawals.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 5 Administrative Personnel 3 2014-01-01 2014-01-01 false Age-based withdrawals. 1650.31 Section... FUNDS FROM THE THRIFT SAVINGS PLAN In-Service Withdrawals § 1650.31 Age-based withdrawals. (a) A participant who has reached age 591/2 and who has not separated from Government service is eligible to...

5 CFR 1650.31 - Age-based withdrawals.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 5 Administrative Personnel 3 2011-01-01 2011-01-01 false Age-based withdrawals. 1650.31 Section... FUNDS FROM THE THRIFT SAVINGS PLAN In-Service Withdrawals § 1650.31 Age-based withdrawals. (a) A participant who has reached age 591/2 and who has not separated from Government employment is eligible to...

Festival Works to Save Pioneering Dances by Black Choreographers.

ERIC Educational Resources Information Center

Biemiller, Lawrence

1988-01-01

The American Dance Festival has begun a three-year effort to encourage scholars to delve into the history and influences of black modern dance, and the Ford Foundation has promised $300,000 to the project. Some express concern about separating black choreography from other American dance. (MSE)

77 FR 22666 - Payment System Risk Policy; Daylight Overdraft Posting Rules

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-17

... of separately-sorted savings bonds and to eliminate a reference to the contractual clearing balance... clearing balance program are effective July 12, 2012. FOR FURTHER INFORMATION CONTACT: Susan V. Foley... account balances according to a set of ``posting rules'' that determine the intraday timing of debits and...

Hollow Fiber Membrane Dehumidification Device for Air Conditioning System.

PubMed

Zhao, Baiwang; Peng, Na; Liang, Canzeng; Yong, Wai Fen; Chung, Tai-Shung

2015-11-16

In order to provide a comfortable living and working environment indoors in tropical countries, the outdoor air often needs to be cooled and dehumidified before it enters the rooms. Membrane separation is an emerging technology for air dehumidification and it is based on the solution diffusion mechanism. Water molecules are preferentially permeating through the membranes due to its smaller kinetic diameter and higher condensability than the other gases. Compared to other dehumidification technologies such as direct cooling or desiccation, there is no phase transition involved in membrane dehumidification, neither the contact between the fresh air stream and the desiccants. Hence, membrane dehumidification would not only require less energy consumption but also avoid cross-contamination problems. A pilot scale air dehumidification system is built in this study which comprises nine pieces of one-inch PAN/PDMS hollow fiber membrane modules. A 150 h long-term test shows that the membrane modules has good water vapor transport properties by using a low vacuum force of only 0.78 bar absolute pressure at the lumen side. The water vapor concentration of the feed humid air decreases dramatically from a range of 18-22 g/m³ to a range of 13.5-18.3 g/m³. Most importantly, the total energy saving is up to 26.2% compared with the conventional air conditioning process.

Case Study for the ARRA-funded GSHP Demonstration at University at Albany

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu, Xiaobing; Malhotra, Mini; Xiong, Zeyu

High initial costs and lack of public awareness of ground-source heat pump (GSHP) technology are the two major barriers preventing rapid deployment of this energy-saving technology in the United States. Under the American Recovery and Reinvestment Act (ARRA), 26 GSHP projects have been competitively selected and carried out to demonstrate the benefits of GSHP systems and innovative technologies for cost reduction and/or performance improvement. This report highlights the findings of a case study of one of the ARRA-funded GSHP demonstration projects—a distributed GSHP system at a new 500-bed apartment-style student residence hall at the University at Albany. This case studymore » is based on the analysis of detailed design documents, measured performance data, published catalog data of heat pump equipment, and actual construction costs. Simulations with a calibrated computer model are performed for both the demonstrated GSHP system and a baseline heating, ventilation, and airconditioning (HVAC) system to determine the energy savings and other related benefits achieved by the GSHP system. The evaluated performance metrics include the energy efficiency of the heat pump equipment and the overall GSHP system, as well as the pumping performance, energy savings, carbon emission reductions, and cost-effectiveness of the demonstrated GSHP system compared with the baseline HVAC system. This case study also identifies opportunities for improving the operational efficiency of the demonstrated GSHP system.« less

A review on waste heat recovery from exhaust in the ceramics industry

NASA Astrophysics Data System (ADS)

Delpech, Bertrand; Axcell, Brian; Jouhara, Hussam

2017-11-01

Following the energy crisis in 1980, many saving technologies have been investigated with attempts to implement them into various industries, one of them is the field of ceramic production. In order to comply with energy saving trends and environmental issues, the European ceramic industry sector has developed energy efficient systems which reduced significantly production time and costs and reduced total energy consumption. The last achievement is of great importance as the energy consumption of the ceramic process accounts for a significant percentage of the total production costs. More precisely, the firing stage consumes the highest amount of energy during the whole ceramic production process. The use of roller kilns, fired by natural gas, involves a loss of 50% of the input energy via the flue gas and the cooling gas exhausts. This review paper briefly describes the production process of the different ceramic products, with a focus on the ceramic sector in Europe. Due to the limited on waste heat recovery in the ceramic industry, other high temperature waste heat recovery applications are considered in the paper, such as in concrete and steel production, which could have a potential use in the ceramic industry. The state of the art technologies used in the ceramics industry are reviewed with a special interest in waste heat recovery from the ceramic process exhaust stacks and energy saving technologies.

Energy Efficient Engine integrated core/low spool design and performance report

NASA Technical Reports Server (NTRS)

Stearns, E. Marshall

1985-01-01

The Energy Efficient Engine (E3) is a NASA program to create fuel saving technology for future transport aircraft engines. The E3 technology advancements were demonstrated to operate reliably and achieve goal performance in tests of the Integrated Core/Low Spool vehicle. The first build of this undeveloped technology research engine set a record for low fuel consumption. Its design and detailed test results are herein presented.

World Wind Tools Reveal Environmental Change

NASA Technical Reports Server (NTRS)

2012-01-01

Originally developed under NASA's Learning Technologies program as a tool to engage and inspire students, World Wind software was released under the NASA Open Source Agreement license. Honolulu, Hawaii based Intelesense Technologies is one of the companies currently making use of the technology for environmental, public health, and other monitoring applications for nonprofit organizations and Government agencies. The company saved about $1 million in development costs by using the NASA software.

An overview of the Small Engine Component Technology (SECT) studies

NASA Technical Reports Server (NTRS)

Vanco, M. R.; Wintucky, W. T.; Niedzwiecki, R. W.

1986-01-01

The objectives of the joint NASA/Army SECT Studies were to identify high payoff technologies for year 2000 small gas turbine engine applications and to provide a technology plan for guiding future research and technology efforts applicable to rotorcraft, commuter and general aviation aircraft and cruise missiles. Competitive contracts were awarded to Allison, AVCO Lycoming, Garrett, Teledyne CAE and Williams International. This paper presents an overview of the contractors' study efforts for the commuter, rotorcraft, cruise missile, and auxiliary power (APU) applications with engines in the 250 to 1,000 horsepower size range. Reference aircraft, missions and engines were selected. Advanced engine configurations and cycles with projected year 2000 component technologies were evaluated and compared with a reference engine selected by the contractor. For typical commuter and rotorcraft applications, fuel savings of 22 percent to 42 percent can be attained. For $1/gallon and $2/gallon fuel, reductions in direct operating cost range from 6 percent to 16 percent and from 11 percent to 17 percent respectively. For subsonic strategic cruise missile applications, fuel savings of 38 percent to 54 percent can be achieved which allows 35 percent to 60 percent increase in mission range and life cycle cost reductions of 40 percent to 56 percent. High payoff technologies have been identified for all applications.

Diseases of the Tricuspid Valve

MedlinePlus

... Daily Conferences Fellowships and Residencies School of Perfusion Technology Education Resources Library & Learning Resource Center CME Resources THI Journal THI Cardiac Society Save the Date: International Symposium on Cardiovascular Regenerative ...

Fermilab Today - Guidelines

Science.gov Websites

range of story topics, including: Professional achievements and milestones (awards, retirements, records -saving practices at the lab Research milestones, records Scientific research, advances in technology The

Kr/Xe Separation over a Chabazite Zeolite Membrane

DOE Office of Scientific and Technical Information (OSTI.GOV)

Feng, Xuhui; Zong, Zhaowang; Elsaidi, Sameh K.

2016-08-10

Cryogenic distillation, the current conventional technology to separate Krypton and Xenon from air, and from nuclear reprocessing technologies, is an energy-intensive and expensive process. Membrane technology could potentially make this challenging industrial separation less energy intensive and economically viable. We demonstrate that chabazite zeolite SAPO-34 membranes effectively separated Kr/Xe gas mixtures at industrially relevant compositions. Control over membrane thickness and average crystal size led to industrial range permeances and high separation selectivities. Specifically, SAPO-34 membranes can separate Kr/Xe mixtures with Kr permeances as high as 361.4 GPU and separation selectivities of 34.8 for molar compositions close to typical concentrations ofmore » these two gases in air. In addition, SAPO-34 membranes separated Kr/Xe mixtures with Kr permeances as high as 525.7 GPU and separation selectivities up to 45.1 for molar compositions as might be encountered in nuclear reprocessing technologies. Molecular sieving and differences in diffusivities were identified as the dominant separation mechanisms.« less

Green Routing Fuel Saving Opportunity Assessment: A Case Study on California Large-Scale Real-World Travel Data: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhu, Lei; Holden, Jacob; Gonder, Jeff

New technologies, such as connected and automated vehicles, have attracted more and more researchers for improving the energy efficiency and environmental impact of current transportation systems. The green routing strategy instructs a vehicle to select the most fuel-efficient route before the vehicle departs. It benefits the current transportation system with fuel saving opportunity through identifying the greenest route. This paper introduces an evaluation framework for estimating benefits of green routing based on large-scale, real-world travel data. The framework has the capability to quantify fuel savings by estimating the fuel consumption of actual routes and comparing to routes procured by navigationmore » systems. A route-based fuel consumption estimation model, considering road traffic conditions, functional class, and road grade is proposed and used in the framework. An experiment using a large-scale data set from the California Household Travel Survey global positioning system trajectory data base indicates that 31% of actual routes have fuel savings potential with a cumulative estimated fuel savings of 12%.« less

Green Routing Fuel Saving Opportunity Assessment: A Case Study on California Large-Scale Real-World Travel Data

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhu, Lei; Holden, Jacob; Gonder, Jeffrey D

New technologies, such as connected and automated vehicles, have attracted more and more researchers for improving the energy efficiency and environmental impact of current transportation systems. The green routing strategy instructs a vehicle to select the most fuel-efficient route before the vehicle departs. It benefits the current transportation system with fuel saving opportunity through identifying the greenest route. This paper introduces an evaluation framework for estimating benefits of green routing based on large-scale, real-world travel data. The framework has the capability to quantify fuel savings by estimating the fuel consumption of actual routes and comparing to routes procured by navigationmore » systems. A route-based fuel consumption estimation model, considering road traffic conditions, functional class, and road grade is proposed and used in the framework. An experiment using a large-scale data set from the California Household Travel Survey global positioning system trajectory data base indicates that 31% of actual routes have fuel savings potential with a cumulative estimated fuel savings of 12%.« less

A novel technology coupling extraction and foam fractionation for separating the total saponins from Achyranthes bidentata.

PubMed

Ding, Linlin; Wang, Yanji; Wu, Zhaoliang; Liu, Wei; Li, Rui; Wang, Yanyan

2016-10-02

A novel technology coupling extraction and foam fractionation was developed for separating the total saponins from Achyranthes bidentata. In the developed technology, the powder of A. bidentata was loaded in a nylon filter cloth pocket with bore diameter of 180 µm. The pocket was fixed in the bulk liquid phase for continuously releasing saponins. Under the optimal conditions, the concentration and the extraction rate of the total saponins in the foamate by the developed technology were 73.5% and 416.2% higher than those by the traditional technology, respectively. The foamates obtained by the traditional technology and the developed technology were analyzed by ultraperformance liquid chromatography-mass spectrometry to determine their ingredients, and the results appeared that the developed technology exhibited a better performance for separating saponins than the traditional technology. The study is expected to develop a novel technology for cost effectively separating plant-derived materials with surface activity.

Emergy-based assessment on industrial symbiosis: a case of Shenyang Economic and Technological Development Zone.

PubMed

Geng, Yong; Liu, Zuoxi; Xue, Bing; Dong, Huijuan; Fujita, Tsuyoshi; Chiu, Anthony

2014-12-01

Industrial symbiosis is the sharing of services, utility, and by-product resources among industries. This is usually made in order to add value, reduce costs, and improve the environment, and therefore has been taken as an effective approach for developing an eco-industrial park, improving resource efficiency, and reducing pollutant emission. Most conventional evaluation approaches ignored the contribution of natural ecosystem to the development of industrial symbiosis and cannot reveal the interrelations between economic development and environmental protection, leading to a need of an innovative evaluation method. Under such a circumstance, we present an emergy analysis-based evaluation method by employing a case study at Shenyang Economic and Technological Development Zone (SETDZ). Specific emergy indicators on industrial symbiosis, including emergy savings and emdollar value of total emergy savings, were developed so that the holistic picture of industrial symbiosis can be presented. Research results show that nonrenewable inputs, imported resource inputs, and associated services could be saved by 89.3, 32.51, and 15.7 %, and the ratio of emergy savings to emergy of the total energy used would be about 25.58 %, and the ratio of the emdollar value of total emergy savings to the total gross regional product (GRP) of SETDZ would be 34.38 % through the implementation of industrial symbiosis. In general, research results indicate that industrial symbiosis could effectively reduce material and energy consumption and improve the overall eco-efficiency. Such a method can provide policy insights to industrial park managers so that they can raise appropriate strategies on developing eco-industrial parks. Useful strategies include identifying more potential industrial symbiosis opportunities, optimizing energy structure, increasing industrial efficiency, recovering local ecosystems, and improving public and industrial awareness of eco-industrial park policies.

Building an Energy-efficient Uplink and Downlink Delay Aware TDM-PON System

NASA Astrophysics Data System (ADS)

Newaz, S. H. Shah; Jang, Min Seok; Alaelddin, Fuad Yousif Mohammed; Lee, Gyu Myoung; Choi, Jun Kyun

2016-05-01

With the increasing concern over the energy expenditure due to rapid ICT expansion and growth of Internet traffic volume, there is a growing trend towards developing energy-efficient ICT solutions. Passive Optical Network (PON), which is regarded as a key enabler to facilitate high speed broadband connection to individual subscribers, is considered as one of the energy-efficient access network technologies. However, an immense amount of research effort can be noticed in academia and industries to make PON more energy-efficient. In this paper, we aim at improving energy saving performance of Time Division Multiplexing (TDM)-PON, which is the most widely deployed PON technology throughout the world. A commonly used approach to make TDM-PON energy-efficient is to use sleep mode in Optical Network Units (ONUs), which are the customer premises equipment of a TDM-PON system. However, there is a strong trade-off relationship between traffic delay performance of an ONU and its energy saving (the longer the sleep interval length of an ONU, the lower its energy consumption, but the higher the traffic delay, and vice versa). In this paper, we propose an Energy-efficient Uplink and Downlink Delay Aware (EUDDA) scheme for TDM-PON system. The prime object of EUDDA is to meet both downlink and uplink traffic delay requirement while maximizing energy saving performance of ONUs as much as possible. In EUDDA, traffic delay requirement is given more priority over energy saving. Even so, it still can improve energy saving of ONUs noticeably. We evaluate performance of EUDDA in front of two existing solutions in terms of traffic delay, jitter, and ONU energy consumption. The performance results show that EUDDA significantly outperforms the other existing solutions.

Back to the Earth.

ERIC Educational Resources Information Center

Abnee, Conn

1999-01-01

Discusses how schools can use geothermal technology to conserve energy and save money. How geothermal climate control works and its payback are examined, and examples of development and use are highlighted. (GR)