Translating Theory into Practice: Implications of Japanese Management Theory for Student Personnel Administrators. NASPA Monograph Series Volume 3. First Edition.

ERIC Educational Resources Information Center

Deegan, William L.; And Others

Japanese management theory was studied to identify specific models for consideration by student personnel administrators. The report is organized into three sections: major components of Japanese management theory, potential implications for student personnel administration, and three models, based on components of Japanese management theory, for…

FOR Allocation to Distribution Systems based on Credible Improvement Potential (CIP)

NASA Astrophysics Data System (ADS)

Tiwary, Aditya; Arya, L. D.; Arya, Rajesh; Choube, S. C.

2017-02-01

This paper describes an algorithm for forced outage rate (FOR) allocation to each section of an electrical distribution system subject to satisfaction of reliability constraints at each load point. These constraints include threshold values of basic reliability indices, for example, failure rate, interruption duration and interruption duration per year at load points. Component improvement potential measure has been used for FOR allocation. Component with greatest magnitude of credible improvement potential (CIP) measure is selected for improving reliability performance. The approach adopted is a monovariable method where one component is selected for FOR allocation and in the next iteration another component is selected for FOR allocation based on the magnitude of CIP. The developed algorithm is implemented on sample radial distribution system.

SSME Post Test Diagnostic System: Systems Section

NASA Technical Reports Server (NTRS)

Bickmore, Timothy

1995-01-01

An assessment of engine and component health is routinely made after each test firing or flight firing of a Space Shuttle Main Engine (SSME). Currently, this health assessment is done by teams of engineers who manually review sensor data, performance data, and engine and component operating histories. Based on review of information from these various sources, an evaluation is made as to the health of each component of the SSME and the preparedness of the engine for another test or flight. The objective of this project - the SSME Post Test Diagnostic System (PTDS) - is to develop a computer program which automates the analysis of test data from the SSME in order to detect and diagnose anomalies. This report primarily covers work on the Systems Section of the PTDS, which automates the analyses performed by the systems/performance group at the Propulsion Branch of NASA Marshall Space Flight Center (MSFC). This group is responsible for assessing the overall health and performance of the engine, and detecting and diagnosing anomalies which involve multiple components (other groups are responsible for analyzing the behavior of specific components). The PTDS utilizes several advanced software technologies to perform its analyses. Raw test data is analyzed using signal processing routines which detect features in the data, such as spikes, shifts, peaks, and drifts. Component analyses are performed by expert systems, which use 'rules-of-thumb' obtained from interviews with the MSFC data analysts to detect and diagnose anomalies. The systems analysis is performed using case-based reasoning. Results of all analyses are stored in a relational database and displayed via an X-window-based graphical user interface which provides ranked lists of anomalies and observations by engine component, along with supporting data plots for each.

Enabling Technologies for Ceramic Hot Section Components

DOE Office of Scientific and Technical Information (OSTI.GOV)

Venkat Vedula; Tania Bhatia

Silicon-based ceramics are attractive materials for use in gas turbine engine hot sections due to their high temperature mechanical and physical properties as well as lower density than metals. The advantages of utilizing ceramic hot section components include weight reduction, and improved efficiency as well as enhanced power output and lower emissions as a result of reducing or eliminating cooling. Potential gas turbine ceramic components for industrial, commercial and/or military high temperature turbine applications include combustor liners, vanes, rotors, and shrouds. These components require materials that can withstand high temperatures and pressures for long duration under steam-rich environments. For Navymore » applications, ceramic hot section components have the potential to increase the operation range. The amount of weight reduced by utilizing a lighter gas turbine can be used to increase fuel storage capacity while a more efficient gas turbine consumes less fuel. Both improvements enable a longer operation range for Navy ships and aircraft. Ceramic hot section components will also be beneficial to the Navy's Growth Joint Strike Fighter (JSF) and VAATE (Versatile Affordable Advanced Turbine Engines) initiatives in terms of reduced weight, cooling air savings, and capability/cost index (CCI). For DOE applications, ceramic hot section components provide an avenue to achieve low emissions while improving efficiency. Combustors made of ceramic material can withstand higher wall temperatures and require less cooling air. Ability of the ceramics to withstand high temperatures enables novel combustor designs that have reduced NO{sub x}, smoke and CO levels. In the turbine section, ceramic vanes and blades do not require sophisticated cooling schemes currently used for metal components. The saved cooling air could be used to further improve efficiency and power output. The objectives of this contract were to develop technologies critical for ceramic hot section components for gas turbine engines. Significant technical progress has been made towards maturation of the EBC and CMC technologies for incorporation into gas turbine engine hot-section. Promising EBC candidates for longer life and/or higher temperature applications relative to current state of the art BSAS-based EBCs have been identified. These next generation coating systems have been scaled-up from coupons to components and are currently being field tested in Solar Centaur 50S engine. CMC combustor liners were designed, fabricated and tested in a FT8 sector rig to demonstrate the benefits of a high temperature material system. Pretest predictions made through the use of perfectly stirred reactor models showed a 2-3x benefit in CO emissions for CMC versus metallic liners. The sector-rig test validated the pretest predictions with >2x benefit in CO at the same NOx levels at various load conditions. The CMC liners also survived several trip shut downs thereby validating the CMC design methodology. Significant technical progress has been made towards incorporation of ceramic matrix composites (CMC) and environmental barrier coatings (EBC) technologies into gas turbine engine hot-section. The second phase of the program focused on the demonstration of a reverse flow annular CMC combustor. This has included overcoming the challenges of design and fabrication of CMCs into 'complex' shapes; developing processing to apply EBCs to 'engine hardware'; testing of an advanced combustor enabled by CMCs in a PW206 rig; and the validation of performance benefits against a metal baseline. The rig test validated many of the pretest predictions with a 40-50% reduction in pattern factor compared to the baseline and reductions in NOx levels at maximum power conditions. The next steps are to develop an understanding of the life limiting mechanisms in EBC and CMC materials, developing a design system for EBC coated CMCs and durability testing in an engine environment.« less

42 CFR § 484.330 - Process for determining and applying the value-based payment adjustment under the Home Health...

Code of Federal Regulations, 2010 CFR

2016-10-01

...-based payment adjustment under the Home Health Value-Based Purchasing (HHVBP) Model. § 484.330 Section... (HHVBP) Model Components for Competing Home Health Agencies Within State Boundaries § 484.330 Process for determining and applying the value-based payment adjustment under the Home Health Value-Based Purchasing...

42 CFR § 484.330 - Process for determining and applying the value-based payment adjustment under the Home Health...

Code of Federal Regulations, 2010 CFR

2017-10-01

...-based payment adjustment under the Home Health Value-Based Purchasing (HHVBP) Model. § 484.330 Section... (HHVBP) Model Components for Competing Home Health Agencies Within State Boundaries § 484.330 Process for determining and applying the value-based payment adjustment under the Home Health Value-Based Purchasing...

Stand-level growth and yield component models for red oak-sweetgum forests on Mid-South minor stream bottoms

Treesearch

Emily B. Schultz; J. Clint Iles; Thomas G. Matney; Andrew W. Ezell; James S. Meadows; Theodor D. Leininger; al. et.

2010-01-01

Greater emphasis is being placed on Southern bottomland hardwood management, but relatively few growth and yield prediction systems exist that are based on sufficient measurements. We present the aggregate stand-level expected yield and structural component equations for a red oak (Quercus section Lobatae)-sweetgum (Liquidambar styraciflua L.) growth and yield model....

Proposal of a calculation method to determine the structural components' contribution on the deceleration of a passenger compartment based on the energy-derivative method.

PubMed

Nagasaka, Kei; Mizuno, Koji; Ito, Daisuke; Saida, Naoya

2017-05-29

In car crashes, the passenger compartment deceleration significantly influences the occupant loading. Hence, it is important to consider how each structural component deforms in order to control the passenger compartment deceleration. In frontal impact tests, the passenger compartment deceleration depends on the energy absorption property of the front structures. However, at this point in time there are few papers describing the components' quantitative contributions on the passenger compartment deceleration. Generally, the cross-sectional force is used to examine each component's contribution to passenger compartment deceleration. However, it is difficult to determine each component's contribution based on the cross-sectional forces, especially within segments of the individual members itself such as the front rails, because the force is transmitted continuously and the cross-sectional forces remain the same through the component. The deceleration of a particle can be determined from the derivative of the kinetic energy. Using this energy-derivative method, the contribution of each component on the passenger compartment deceleration can be determined. Using finite element (FE) car models, this method was applied for full-width and offset impact tests. This method was also applied to evaluate the deceleration of the powertrain. The finite impulse response (FIR) coefficient of the vehicle deceleration (input) and the driver chest deceleration (output) was calculated from Japan New Car Assessment Program (JNCAP) tests. These were applied to the component's contribution on the vehicle deceleration in FE analysis, and the component's contribution to the deceleration of the driver's chest was determined. The sum of the contribution of each component coincides with the passenger compartment deceleration in all types of impacts; therefore, the validity of this method was confirmed. In the full-width impact, the contribution of the crush box was large in the initial phases, and the contribution of the passenger compartment was large in the final phases. For the powertrain deceleration, the crush box had a positive contribution and the passenger compartment had a negative contribution. In the offset test, the contribution of the honeycomb and the passenger compartment deformation to the passenger compartment deceleration was large. Based on the FIR analysis, the passenger compartment deformation contributed the most to the chest deceleration of the driver dummy in the full-width impact. Based on the energy-derivative method, the contribution of the components' deformation to deceleration of the passenger compartment can be calculated for various types of crash configurations more easily, directly, and quantitatively than by using conventional methods. In addition, by combining the energy-derivative method and FIR, each structure's contribution to the occupant deceleration can be obtained. The energy-derivative method is useful in investigating how the deceleration develops from component deformations and also in designing deceleration curves for various impact configurations.

Design, Analysis and Fabrication of Secondary Structural Components for the Habitat Demonstration Unit-Deep Space Habitat

NASA Technical Reports Server (NTRS)

Smith, Russell W.; Langford, William M.

2012-01-01

In support of NASA s Habitat Demonstration Unit - Deep Space Habitat Prototype, a number of evolved structural sections were designed, fabricated, analyzed and installed in the 5 meter diameter prototype. The hardware consisted of three principal structural sections, and included the development of novel fastener insert concepts. The articles developed consisted of: 1) 1/8th of the primary flooring section, 2) an inner radius floor beam support which interfaced with, and supported (1), 3) two upper hatch section prototypes, and 4) novel insert designs for mechanical fastener attachments. Advanced manufacturing approaches were utilized in the fabrication of the components. The structural components were developed using current commercial aircraft constructions as a baseline (for both the flooring components and their associated mechanical fastener inserts). The structural sections utilized honeycomb sandwich panels. The core section consisted of 1/8th inch cell size Nomex, at 9 lbs/cu ft, and which was 0.66 inches thick. The facesheets had 3 plys each, with a thickness of 0.010 inches per ply, made from woven E-glass with epoxy reinforcement. Analysis activities consisted of both analytical models, as well as initial closed form calculations. Testing was conducted to help verify analysis model inputs, as well as to facilitate correlation between testing and analysis. Test activities consisted of both 4 point bending tests as well as compressive core crush sequences. This paper presents an overview of this activity, and discusses issues encountered during the various phases of the applied research effort, and its relevance to future space based habitats.

Layer Additive Production or Manufacturing of Thick Sections of Ti-6Al-4V by Selective Electron Beam Melting (SEBM)

NASA Astrophysics Data System (ADS)

Sun, Y. Y.; Gulizia, S.; Fraser, D.; Oh, C. H.; Lu, S. L.; Qian, M.

2017-10-01

Selective electron beam melting (SEBM) is an established layer additive manufacturing or production process for small-to-medium-sized components of Ti-6Al-4V. Current literature data on SEBM of Ti-6Al-4V are, however, based principally on thin-section (<1″; mostly <0.5″) samples or components. In this research, 34-mm-thick (1.34″) Ti-6Al-4V block samples were produced through use of default Arcam SEBM parameters and characterized versus section thickness. High densities (99.4-99.8%) were achieved across different thick sections, but markedly inhomogeneous microstructures also developed. Nonetheless, the tensile properties measured from 27 different thickness-width positions all clearly satisfied the minimum requirements for mill-annealed Ti-6Al-4V. SEBM produced highly dense thick sections of Ti-6Al-4V with good tensile properties. Large lack-of-fusion defects (80-250 µm) were found to be mainly responsible for variations in tensile properties.

Diffractive dijet cross sections in photoproduction at HERA

NASA Astrophysics Data System (ADS)

Breitweg, J.; Derrick, M.; Krakauer, D.; Magill, S.; Mikunas, D.; Musgrave, B.; Repond, J.; Stanek, R.; Talaga, R. L.; Yoshida, R.; Zhang, H.; Mattingly, M. C. K.; Anselmo, F.; Antonioli, P.; Bari, G.; Basile, M.; Bellagamba, L.; Boscherini, D.; Bruni, A.; Bruni, G.; Romeo, G. Cara; Castellini, G.; Cifarelli, L.; Cindolo, F.; Contin, A.; Coppola, N.; Corradi, M.; de Pasquale, S.; Giusti, P.; Iacobucci, G.; Laurenti, G.; Levi, G.; Margotti, A.; Massam, T.; Nania, R.; Palmonari, F.; Pesci, A.; Polini, A.; Sartorelli, G.; Garcia, Y. Zamora; Zichichi, A.; Amelung, C.; Bornheim, A.; Brock, I.; Coböken, K.; Crittenden, J.; Deffner, R.; Eckert, M.; Grothe, M.; Hartmann, H.; Heinloth, K.; Heinz, L.; Hilger, E.; Jakob, H.-P.; Kappes, A.; Katz, U. F.; Kerger, R.; Paul, E.; Pfeiffer, M.; Stamm, J.; Wieber, H.; Bailey, D. S.; Campbell-Robson, S.; Cottingham, W. N.; Foster, B.; Hall-Wilton, R.; Heath, G. P.; Heath, H. F.; McFall, J. D.; Piccioni, D.; Roff, D. G.; Tapper, R. J.; Ayad, R.; Capua, M.; Iannotti, L.; Schioppa, M.; Susinno, G.; Kim, J. Y.; Lee, J. H.; Lim, I. T.; Pac, M. Y.; Caldwell, A.; Cartiglia, N.; Jing, Z.; Liu, W.; Mellado, B.; Parsons, J. A.; Ritz, S.; Sampson, S.; Sciulli, F.; Straub, P. B.; Zhu, Q.; Borzemski, P.; Chwastowski, J.; Eskreys, A.; Figiel, J.; Klimek, K.; Przybycień, M. B.; Zawiejski, L.; Adamczyk, L.; Bednarek, B.; Bukowy, M.; Czermak, A. M.; Jeleń, K.; Kisielewska, D.; Kowalski, T.; Przybycień, M.; Rulikowska-Zarbska, E.; Suszycki, L.; Zajc, J.; Duliński, Z.; Kotański, A.; Abbiendi, G.; Bauerdick, L. A. T.; Behrens, U.; Beier, H.; Bienlein, J. K.; Desler, K.; Drews, G.; Fricke, U.; Gialas, I.; Goebel, F.; Göttlicher, P.; Graciani, R.; Haas, T.; Hain, W.; Hasell, D.; Hebbel, K.; Johnson, K. F.; Kasemann, M.; Koch, W.; Kötz, U.; Kowalski, H.; Lindemann, L.; Löhr, B.; Milewski, J.; Milite, M.; Monteiro, T.; Ng, J. S. T.; Notz, D.; Park, I. H.; Pellegrino, A.; Pelucchi, F.; Piotrzkowski, K.; Rohde, M.; Roldán, J.; Ryan, J. J.; Savin, A. A.; Schneekloth, U.; Schwarzer, O.; Selonke, F.; Stonjek, S.; Surrow, B.; Tassi, E.; Westphal, D.; Wolf, G.; Wollmer, U.; Youngman, C.; Zeuner, W.; Burow, B. D.; Coldewey, C.; Grabosch, H. J.; Meyer, A.; Schlenstedt, S.; Barbagli, G.; Gallo, E.; Pelfer, P.; Maccarrone, G.; Votano, L.; Bamberger, A.; Eisenhardt, S.; Markun, P.; Raach, H.; Trefzger, T.; Wölfle, S.; Bromley, J. T.; Brook, N. H.; Bussey, P. J.; Doyle, A. T.; MacDonald, N.; Saxon, D. H.; Sinclair, L. E.; Skillicorn, I. O.; Strickland, E.; Waugh, R.; Bohnet, I.; Gendner, N.; Holm, U.; Meyer-Larsen, A.; Salehi, H.; Wick, K.; Garfagnini, A.; Gladilin, L. K.; Horstmann, D.; Kçira, D.; Klanner, R.; Lohrmann, E.; Poelz, G.; Schott, W.; Zetsche, F.; Bacon, T. C.; Butterworth, I.; Cole, J. E.; Howell, G.; Lamberti, L.; Long, K. R.; Miller, D. B.; Pavel, N.; Prinias, A.; Sedgbeer, J. K.; Sideris, D.; Walker, R.; Mallik, U.; Wang, S. M.; Wu, J. T.; Cloth, P.; Filges, D.; Fleck, J. I.; Ishii, T.; Kuze, M.; Suzuki, I.; Tokushuku, K.; Yamada, S.; Yamauchi, K.; Yamazaki, Y.; Hong, S. J.; Lee, S. B.; Nam, S. W.; Park, S. K.; Barreiro, F.; Fernández, J. P.; García, G.; Glasman, C.; Hernández, J. M.; Hervás, L.; Labarga, L.; Martínez, M.; Peso, J. Del; Puga, J.; Terrón, J.; Trocóniz, J. F. De; Corriveau, F.; Hanna, D. S.; Hartmann, J.; Hung, L. W.; Murray, W. N.; Ochs, A.; Riveline, M.; Stairs, D. G.; St-Laurent, M.; Ullmann, R.; Tsurugai, T.; Bashkirov, V.; Dolgoshein, B. A.; Stifutkin, A.; Bashindzhagyan, G. L.; Ermolov, P. F.; Golubkov, Yu. A.; Khein, L. A.; Korotkova, N. A.; Korzhavina, I. A.; Kuzinin, V. A.; Lukina, O. Yu.; Proskuryakov, A. S.; Shcheglova, L. M.; Solomin, A. N.; Zotkin, S. A.; Bokel, C.; Botje, M.; Brümmer, N.; Engelen, J.; Koffeman, E.; Kooijman, P.; van Sighem, A.; Tiecke, H.; Tuning, N.; Verkerke, W.; Vossebeld, J.; Wiggers, L.; Wolf, E. De; Acosta, D.; Bylsma, B.; Durkin, L. S.; Gilmore, J.; Ginsburg, C. M.; Kim, C. L.; Ling, T. Y.; Nylander, P.; Romanowski, T. A.; Blaikley, H. E.; Cashmore, R. J.; Cooper-Sarkar, A. M.; Devenish, R. C. E.; Edmonds, J. K.; Große-Knetter, J.; Harnew, N.; Nath, C.; Noyes, V. A.; Quadt, A.; Ruske, O.; Tickner, J. R.; Walczak, R.; Waters, D. S.; Bertolin, A.; Brugnera, R.; Carlin, R.; Corso, F. Dal; Dosselli, U.; Limentani, S.; Morandin, M.; Posocco, M.; Stanco, L.; Stroili, R.; Voci, C.; Bulmahn, J.; Oh, B. Y.; Okrasiński, J. R.; Toothacker, W. S.; Whitmore, J. J.; Iga, Y.; D'Agostini, G.; Marini, G.; Nigro, A.; Raso, M.; Hart, J. C.; McCubbin, N. A.; Shah, T. P.; Epperson, D.; Heusch, C.; Rahn, J. T.; Sadrozinski, H. F.-W.; Seiden, A.; Wichmann, R.; Williams, D. C.; Abramowicz, H.; Briskin, G.; Dagan, S.; Kananov, S.; Levy, A.; Abe, T.; Fusayasu, T.; Inuzuka, M.; Nagano, K.; Umemori, K.; Yamashita, T.; Hamatsu, R.; Hirose, T.; Homma, K.; Kitamura, S.; Matsushita, T.; Arneodo, M.; Cirio, R.; Costa, M.; Ferrero, M. I.; Maselli, S.; Monaco, V.; Peroni, C.; Petrucci, M. C.; Ruspa, M.; Sacchi, R.; Solano, A.; Staiano, A.; Dardo, M.; Bailey, D. C.; Fagerstroem, C.-P.; Galea, R.; Hartner, G. F.; Joo, K. K.; Levman, G. M.; Martin, J. F.; Orr, R. S.; Polenz, S.; Sabetfakhri, A.; Simmons, D.; Teuscher, R. J.; Butterworth, J. M.; Catterall, C. D.; Hayes, M. E.; Jones, T. W.; Lane, J. B.; Saunders, R. L.; Sutton, M. R.; Wing, M.; Ciborowski, J.; Grzelak, G.; Kasprzak, M.; Nowak, R. J.; Pawlak, J. M.; Pawlak, R.; Tymieniecka, T.; Wróblewski, A. K.; Zakrzewski, J. A.; Zarnecki, A. F.; Adamus, M.; Deppe, O.; Eisenberg, Y.; Hochman, D.; Karshon, U.; Badgett, W. F.; Chapin, D.; Cross, R.; Dasu, S.; Foudas, C.; Loveless, R. J.; Mattingly, S.; Reeder, D. D.; Smith, W. H.; Vaiciulis, A.; Wodarczyk, M.; Deshpande, A.; Dhawan, S.; Hughes, V. W.; Bhadra, S.; Frisken, W. R.; Khakzad, M.; Schmidke, W. B.

1998-08-01

Differential dijet cross sections have been measured with the ZEUS detector for photoproduction events in which the hadronic final state containing the jets is separated with respect to the outgoing proton direction by a large rapidity gap. The cross section has been measured as a function of the fraction of the photon (ϰγ OBS) and pomeron (β OBS) momentum participating in the production of the dijet system. The observed ϰγ OBS dependence shows evidence for the presence of a resolved- as well as a direct-photon component. The measured cross section da/dβ OBS increases as β OBS increases indicating that there is a sizeable contribution to dijet production from those events in which a large fraction of the pomeron momentum participates in the hard scattering. These cross sections and the ZEUS measurements of the diffractive structure function can be described by calculations based on parton densities in the pomeron which evolve according to the QCD evolution equations and include a substantial hard momentum component of gluons in the pomeron.

On 3-D inelastic analysis methods for hot section components (base program)

NASA Technical Reports Server (NTRS)

Wilson, R. B.; Bak, M. J.; Nakazawa, S.; Banerjee, P. K.

1986-01-01

A 3-D Inelastic Analysis Method program is described. This program consists of a series of new computer codes embodying a progression of mathematical models (mechanics of materials, special finite element, boundary element) for streamlined analysis of: (1) combustor liners, (2) turbine blades, and (3) turbine vanes. These models address the effects of high temperatures and thermal/mechanical loadings on the local (stress/strain)and global (dynamics, buckling) structural behavior of the three selected components. Three computer codes, referred to as MOMM (Mechanics of Materials Model), MHOST (Marc-Hot Section Technology), and BEST (Boundary Element Stress Technology), have been developed and are briefly described in this report.

78 FR 13895 - Certain Wireless Communications Base Stations and Components Thereof; Institution of...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-01

... INTERNATIONAL TRADE COMMISSION [Investigation No. 337-TA-871] Certain Wireless Communications Base.... International Trade Commission. ACTION: Notice. SUMMARY: Notice is hereby given that a complaint was filed with the U.S. International Trade Commission on January 24, 2013, under section 337 of the Tariff Act of...

49 CFR 173.165 - Polyester resin kits.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 49 Transportation 2 2012-10-01 2012-10-01 false Polyester resin kits. 173.165 Section 173.165... Polyester resin kits. (a) Except for transportation by aircraft, polyester resin kits consisting of a base... resin kits consisting of a base material component (Class 3, Packing Group II or III) and an activator...

Developing Flowcharted Procedures Manuals for School District Administration within the ISO 9000 Context.

ERIC Educational Resources Information Center

Schoch, Robert

2002-01-01

Describes how the School District of Lancaster, Pennsylvania, implemented a districtwide quality-management system based on the Geneva-based International Standards Organization 9001, a major component of which is the documentation of procedures. Includes sections on implementation, procedure manuals, quality management, uniformity, formatting,…

42 CFR 422.258 - Calculation of benchmarks.

Code of Federal Regulations, 2011 CFR

2011-10-01

... section 1853(n)(2) of Act. The weights for each component are based on the phase-in period assigned each... phase-in period, the blended benchmark for an area for a year equals the section 1853(n)(2) of the Act... year after 2012, there is a change in the quartile in which an area is ranked compared to the previous...

Dielectric waveguide with transverse index variation that support a zero group velocity mode at a non-zero longitudinal wavevector

DOEpatents

Ibanescu, Mihai; Joannopoious, John D.; Fink, Yoel; Johnson, Steven G.; Fan, Shanhui

2005-06-21

Optical components including a laser based on a dielectric waveguide extending along a waveguide axis and having a refractive index cross-section perpendicular to the waveguide axis, the refractive index cross-section supporting an electromagnetic mode having a zero group velocity for a non-zero wavevector along the waveguide axis.

New Hampshire Early Childhood Professional Development System: Guide to Early Childhood Careers.

ERIC Educational Resources Information Center

McDonnell, Tessa, Ed.

The community of child care providers in New Hampshire has adopted the Early Childhood Professional Development System as an initial step toward assuring quality care and education for children. This guide describes the components of that system and is presented in eight sections. Section 1 of the guide introduces the system based on a set of two…

Energy efficient engine high-pressure turbine supersonic cascade technology report

NASA Technical Reports Server (NTRS)

Kopper, F. C.; Milano, R.; Davis, R. L.; Dring, R. P.; Stoeffler, R. C.

1981-01-01

The performance of two vane endwall geometries and three blade sections for the high-pressure turbine was evaluated in terms of the efficiency requirements of the Energy Efficient Engine high-pressure turbine component. The van endwall designs featured a straight wall and S-wall configuration. The blade designs included a base blade, straightback blade, and overcambered blade. Test results indicated that the S-wall vane configuration and the base blade configuration offered the most promising performance characteristics for the Energy Efficient Engine high-pressure turbine component.

Creep fatigue life prediction for engine hot section materials (isotropic)

NASA Technical Reports Server (NTRS)

Moreno, Vito; Nissley, David; Lin, Li-Sen Jim

1985-01-01

The first two years of a two-phase program aimed at improving the high temperature crack initiation life prediction technology for gas turbine hot section components are discussed. In Phase 1 (baseline) effort, low cycle fatigue (LCF) models, using a data base generated for a cast nickel base gas turbine hot section alloy (B1900+Hf), were evaluated for their ability to predict the crack initiation life for relevant creep-fatigue loading conditions and to define data required for determination of model constants. The variables included strain range and rate, mean strain, strain hold times and temperature. None of the models predicted all of the life trends within reasonable data requirements. A Cycle Damage Accumulation (CDA) was therefore developed which follows an exhaustion of material ductility approach. Material ductility is estimated based on observed similarities of deformation structure between fatigue, tensile and creep tests. The cycle damage function is based on total strain range, maximum stress and stress amplitude and includes both time independent and time dependent components. The CDA model accurately predicts all of the trends in creep-fatigue life with loading conditions. In addition, all of the CDA model constants are determinable from rapid cycle, fully reversed fatigue tests and monotonic tensile and/or creep data.

Calculation on spectrum of direct DNA damage induced by low-energy electrons including dissociative electron attachment.

PubMed

Liu, Wei; Tan, Zhenyu; Zhang, Liming; Champion, Christophe

2017-03-01

In this work, direct DNA damage induced by low-energy electrons (sub-keV) is simulated using a Monte Carlo method. The characteristics of the present simulation are to consider the new mechanism of DNA damage due to dissociative electron attachment (DEA) and to allow determining damage to specific bases (i.e., adenine, thymine, guanine, or cytosine). The electron track structure in liquid water is generated, based on the dielectric response model for describing electron inelastic scattering and on a free-parameter theoretical model and the NIST database for calculating electron elastic scattering. Ionization cross sections of DNA bases are used to generate base radicals, and available DEA cross sections of DNA components are applied for determining DNA-strand breaks and base damage induced by sub-ionization electrons. The electron elastic scattering from DNA components is simulated using cross sections from different theoretical calculations. The resulting yields of various strand breaks and base damage in cellular environment are given. Especially, the contributions of sub-ionization electrons to various strand breaks and base damage are quantitatively presented, and the correlation between complex clustered DNA damage and the corresponding damaged bases is explored. This work shows that the contribution of sub-ionization electrons to strand breaks is substantial, up to about 40-70%, and this contribution is mainly focused on single-strand break. In addition, the base damage induced by sub-ionization electrons contributes to about 20-40% of the total base damage, and there is an evident correlation between single-strand break and damaged base pair A-T.

NASA JPL Distributed Systems Technology (DST) Object-Oriented Component Approach for Software Inter-Operability and Reuse

NASA Technical Reports Server (NTRS)

Hall, Laverne; Hung, Chaw-Kwei; Lin, Imin

2000-01-01

The purpose of this paper is to provide a description of NASA JPL Distributed Systems Technology (DST) Section's object-oriented component approach to open inter-operable systems software development and software reuse. It will address what is meant by the terminology object component software, give an overview of the component-based development approach and how it relates to infrastructure support of software architectures and promotes reuse, enumerate on the benefits of this approach, and give examples of application prototypes demonstrating its usage and advantages. Utilization of the object-oriented component technology approach for system development and software reuse will apply to several areas within JPL, and possibly across other NASA Centers.

Multispectral Digital Image Analysis of Varved Sediments in Thin Sections

NASA Astrophysics Data System (ADS)

Jäger, K.; Rein, B.; Dietrich, S.

2006-12-01

An update of the recently developed method COMPONENTS (Rein, 2003, Rein & Jäger, subm.) for the discrimination of sediment components in thin sections is presented here. COMPONENTS uses a 6-band (multispectral) image analysis. To derive six-band spectral information of the sediments, thin sections are scanned with a digital camera mounted on a polarizing microscope. The thin sections are scanned twice, under polarized and under unpolarized plain light. During each run RGB images are acquired which are subsequently stacked to a six-band file. The first three bands (Blue=1, Green=2, Red=3) result from the spectral behaviour in the blue, green and red band with unpolarized light conditions, and the bands 4 to 6 (Blue=4, Green=5, Red=6) from the polarized light run. The next step is the discrimination of the sediment components by their transmission behaviour. Automatic classification algorithms broadly used in remote sensing applications cannot be used due to unavoidable variations of sediment particle or thin section thicknesses that change absolute grey values of the sediment components. Thus, we use an approach based on band ratios, also known as indices. By using band ratios, the grey values measured in different bands are normalized against each other and illumination variations (e.g. thickness variations) are eliminated. By combining specific ratios we are able to detect all seven major components in the investigated sediments (carbonates, diatoms, fine clastic material, plant rests, pyrite, quartz and resin). Then, the classification results (compositional maps) are validated. Although the automatic classification and the analogous classification show high concordances, some systematic errors could be identified. For example, the transition zone between the sediment and resin filled cracks is classified as fine clastic material and very coarse carbonates are partly classified as quartz because coarse carbonates can be very bright and spectra are partly saturated (grey value 255). With reduced illumination intensity "carbonate image pixels" get unsaturated and can be well distinguished from quartz grains. During the evaluation process we identify all falsely classified areas using neighbourhood matrices and reclassify them. Finally, we use filter techniques to derive downcore component frequencies from the classified thin section images for variable thick virtual samples. The filter conducts neighbourhood analyses. After filtering, each pixel of the filtered images carries the information about the frequency of any given component in a defined neighbourhood around (virtual sampling). References Rein, B. (2003) In-situ Reflektionsspektroskopie und digitale Bildanalyse Gewinnung hochauflösender Paläoumweltdaten mit fernerkundlichen Methoden, Habilitation Thesis, Univ. Mainz, 104 p. Jäger, K. and Rein, B. (2005): Identifying varve components using digital image analysis techniques. - in: Heidi Haas, Karl Ramseyer & Fritz Schlunegger (eds.): Sediment 2005 (18th-20th July 2005), Schriftenreihe der Deutschen Gesellschaft für Geowissenschaften, 38, p. 81 Rein, B. and Jäger, K. (subm.) COMPONENTS - Sediment component detection in thin sections by multispectral digital image analysis. Sedimentology.

Identification of tissular origin of particles based on autofluorescence multispectral image analysis at the macroscopic scale

NASA Astrophysics Data System (ADS)

Corcel, Mathias; Devaux, Marie-Françoise; Guillon, Fabienne; Barron, Cécile

2017-06-01

Powders produced from plant materials are heterogeneous in relation to native plant heterogeneity, and during grinding, dissociation often occurred at the tissue scale. The tissue composition of powdery samples could be modified through dry fractionation diagrams and impact their end-uses properties. If tissue identification is often made on native plant structure, this characterization is not straightforward in destructured samples such powders. Taking advantage of the autofluorescence properties of cell wall components, multispectral image acquisition is envisioned to identify the tissular origin of particles. Images were acquired on maize stem sections and ground tissues isolated from the same stem by hand dissection. The variability in fluorescence intensity profiles was analysed using principal component analysis. The correspondence between fluorescence profiles and the different tissues observed in maize sections was assessed based on histology or known compositional heterogeneity. Similar variability was encountered in fluorescence profiles extracted from powder leading to the potential ability to predict tissular origin based on this autofluorescence multispectral signal.

34 CFR 694.10 - What are the requirements for awards under the program's scholarship component under section 404E...

Code of Federal Regulations, 2010 CFR

2010-07-01

...'s scholarship component under section 404E of the HEA? 694.10 Section 694.10 Education Regulations... What are the requirements for awards under the program's scholarship component under section 404E of the HEA? (a) Amount of scholarship. (1) Except as provided in paragraph (a)(2) of this section, the...

Application of Time-Frequency Representations To Non-Stationary Radar Cross Section

DTIC Science & Technology

2009-03-01

The three- dimensional plot produced by a TFR allows one to determine which spectral components of a signal vary with time [25... a range bin ( of width cT 2 ) from the stepped frequency waveform. 2. Cancel the clutter (stationary components) by zeroing out points associated with ...generating an infinite number of bilinear Time Frequency distributions based on a generalized equation and a change- able

Work-Based Learning: A Resource Guide for Change.

ERIC Educational Resources Information Center

Hudson River Center for Program Development, Glenmont, NY.

This document is intended to provide New York schools, business/industry representatives, and others with resources to develop or further refine work-based learning (WBL) strategies or components. Section 1 presents background information on the following topics: (1) the scope of WBL; (2) foundations for the development of WBL; (3) categories of…

TNT: Nontraditional Occupations. Practical Arts. Instructor's Manual. Competency-Based Vocational Education.

ERIC Educational Resources Information Center

Sparks, Mavis C.; And Others

Designed to be incorporated into career exploration programs in grades 6-9, this nontraditional occupations unit is a component in the Think Nontraditional Series curriculum and is prepared in a competency-based format. The reading level is approximately seventh grade. A course introduction section contains description and purpose of the…

78 FR 68475 - Certain Vision-Based Driver Assistance System Cameras and Components Thereof; Institution of...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-11-14

... INTERNATIONAL TRADE COMMISSION [Inv. No. 337-TA-899] Certain Vision-Based Driver Assistance System.... International Trade Commission. ACTION: Notice. SUMMARY: Notice is hereby given that a complaint was filed with the U.S. International Trade Commission on September 20, 2013, under section 337 of the Tariff Act of...

16 CFR 1500.5 - Hazardous mixtures.

Code of Federal Regulations, 2010 CFR

2010-01-01

... defined by section 2(f) of the act (repeated in § 1500.3(b)(4)) should be based on the physical, chemical... hazardous or more hazardous than its components because of synergistic or antagonistic reactions. It may not...

Methods for assessing wall interference in the 2- by 2-foot adaptive-wall wind tunnel

NASA Technical Reports Server (NTRS)

Schairer, E. T.

1986-01-01

Discussed are two methods for assessing two-dimensional wall interference in the adaptive-wall test section of the NASA Ames 2 x 2-Foot Transonic Wind Tunnel: (1) a method for predicting free-air conditions near the walls of the test section (adaptive-wall methods); and (2) a method for estimating wall-induced velocities near the model (correction methods), both of which methods are based on measurements of either one or two components of flow velocity near the walls of the test section. Each method is demonstrated using simulated wind tunnel data and is compared with other methods of the same type. The two-component adaptive-wall and correction methods were found to be preferable to the corresponding one-component methods because: (1) they are more sensitive to, and give a more complete description of, wall interference; (2) they require measurements at fewer locations; (3) they can be used to establish free-stream conditions; and (4) they are independent of a description of the model and constants of integration.

Improving cancer treatment with cyclotron produced radionuclides. Progress report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Larson, S.M.; Finn, R.D.

1993-11-01

This report describes our continuing long term goal of promoting nuclear medicine applications by improving the scientific basis for tumor diagnosis, treatment and treatment follow-up based on the use of cyclotron produced radiotracers in oncology. The program includes 3 interactive components: Radiochemistry/Cyclotron; Pharmacology; and Immunology. An essential strategy is as follows: novel radionuclides and radiotracers developed in the Radiochemistry/Cyclotron section will be employed in the Pharmacology and Immunology sections during the next year. The development of novel radionuclides and tracers is of course useful in and of itself, but their utility is greatly enhanced by the interaction with the immunologymore » and pharmacology components of the program.« less

Object linking in repositories

NASA Technical Reports Server (NTRS)

Eichmann, David (Editor); Beck, Jon; Atkins, John; Bailey, Bill

1992-01-01

This topic is covered in three sections. The first section explores some of the architectural ramifications of extending the Eichmann/Atkins lattice-based classification scheme to encompass the assets of the full life cycle of software development. A model is considered that provides explicit links between objects in addition to the edges connecting classification vertices in the standard lattice. The second section gives a description of the efforts to implement the repository architecture using a commercially available object-oriented database management system. Some of the features of this implementation are described, and some of the next steps to be taken to produce a working prototype of the repository are pointed out. In the final section, it is argued that design and instantiation of reusable components have competing criteria (design-for-reuse strives for generality, design-with-reuse strives for specificity) and that providing mechanisms for each can be complementary rather than antagonistic. In particular, it is demonstrated how program slicing techniques can be applied to customization of reusable components.

International VLBI Service for Geodesy and Astrometry 2000 Annual Report

NASA Technical Reports Server (NTRS)

Vandenberg, N. R. (Editor); Baver, K. D. (Editor); Smith, David E. (Technical Monitor)

2000-01-01

This volume of reports is the 2000 Annual Report of the International Very Long Base Interferometry (VLBI) Service for Geodesy and Astrometry (IVS). The individual reports were contributed by VLBI groups in the international geodetic and astrometric community who constitute the permanent components of IVS. The IVS 2000 Annual Report documents the work of the IVS components for the period March 1, 1999 (the official inauguration date of IVS) through December 31, 2000. The reports document changes, activities, and progress of the IVS. The entire contents of this Annual Report also appear on the IVS web site at http://ivscc.gsfc.nasa.gov/publications/ar2000. This book and the web site are organized as follows: (1) The first section contains general information about IVS, a map showing the location of the components, information about the Directing Board members, and the report of the IVS Chair; (2) The second section of Special Reports contains a status report of the IVS Working Group on GPS phase center mapping, a reproduction of the resolution making IVS a Service of the International Astronomical Union (IAU), and a reprint of the VLBI Standard Interface (VSI); (3) The next seven sections hold the component reports from the Coordinators, Network Stations, Operation Centers, Correlators, Data Centers, Analysis Centers, and Technology Development Centers; and (4) The last section includes reference information about IVS: the Terms of Reference, the lists of Member and Affiliated organizations, the IVS Associate Member list, a complete list of IVS components, the list of institutions contributing to this report, and a list of acronyms. The 2000 Annual Report demonstrates the vitality of the IVS and the outstanding progress we have made during our first 22 months.

Nontraditional Fog Seal for Asphalt Pavement : Performance on Shoulder Sections in Minnesota

DOT National Transportation Integrated Search

2018-05-01

The pavement engineering community has recently been introduced to a number of nontraditional products intended for uses as surface sealers for bituminous pavements. Many new products use agricultural-based components and little is known regarding th...

Reliability Prediction for Combustors and Turbines. Volume I.

DTIC Science & Technology

1977-06-01

comprised of many sophisticated components utilizing the latest in high-strength materials and technology. This is especially true in the turbine component...JT9D engine. This inspection technique makes use of a horoscope probe to look into the en- gine hot section while the engine remains installed in the...engine can now be removed based on results observed with the horoscope . This type of failure can be caused by any of the three primary turbine airfoil

Radar cross section fundamentals for the aircraft designer

NASA Technical Reports Server (NTRS)

Stadmore, H. A.

1979-01-01

Various aspects of radar cross-section (RCS) techniques are summarized, with emphasis placed on fundamental electromagnetic phenomena, such as plane and spherical wave formulations, and the definition of RCS is given in the far-field sense. The basic relationship between electronic countermeasures and a signature level is discussed in terms of the detectability range of a target vehicle. Fundamental radar-signature analysis techniques, such as the physical-optics and geometrical-optics approximations, are presented along with examples in terms of aircraft components. Methods of analysis based on the geometrical theory of diffraction are considered and various wave-propagation phenomena are related to local vehicle geometry. Typical vehicle components are also discussed, together with their contribution to total vehicle RCS and their individual signature sensitivities.

Comparison of CDOM EEMs Characteristics along F and PN section in Eastern China Sea: significance for sources tracing

NASA Astrophysics Data System (ADS)

Du, Yong; Zhang, Xiaoyu; Jiang, Binbin; Huang, Dasong; Yao, Lingling

2015-04-01

In this paper, a total of 28 water samples were collected mainly from three sections(C section in the Yangtze river inner estuary, PN section and F section on the spindle of Changjiang diluted water influenced by different hydrodynamic processes),which taken on two cruises in spring and summer of 2011. Absorption and fluorescence spectroscopy were measured along with dissolved organic carbon(DOC) concentrations and temperature, salinity and another environmental parameters to characterize the material sources and environmental implications of dissolved organic matter(DOM). Two protein-like components(tyrosine-like peak B and tryptophan-like peak T1), and two humic-like components(marine humic-like peak M and ultraviolet region humic-like peak A ) were identified by PARAFAC. We discussed CDOM distribution characteristic, material composition, and influence factors during the slowly dilution process of Changjiang diluted water into the east China sea by comparing the correlation of the CDOM absorption, fluorescence intensity, and fluorescence peak with DOC, in order to provide the based biogeochemistry theory basis for building DOC implications using CDOM fluorescence properties. The results revealed that:1) the Yangtze river and its inner estuary (upstream of the river mouth) were detected a higher amount of humic-like components. With the rapid dilution (or settlement) at the inner estuary, the humic-like components would further spread and dilute slowly on PN section and F section. On PN section, the terrigenous material is the main source material, and the main mechanism of CDOM distribution characteristics is controlled by dilution diffusion. Affected by the water mass convergence, marine dissolved organic matter in local waters had obvious input. However, due to the complexed hydrodynamic environment on F section, the input of terrigenous material has many ways. The influence of marine dissolved organic matter increased with the offshore distance increases.2) Although the absorption coefficient of DOC has good instruction significance, CDOM fluorescence intensity can more accurately express the amount of DOC in water than that of absorption coefficient with the source of dissolved organic matter enhanced.3) In general, CDOM fluorescence intensity and DOC show good linear relationship in the study region. But the correlation would change in different sea, and may ignore the rapidly dilution(or possibly sedimentation process) of estuarine waters, which need to be further depth study. Keywords: CDOM; F section; PN section; sources tracing; hydrodynamic environment

X-Ray Fluorescence Solvent Detection at the Substrate-Adhesive Interface

NASA Technical Reports Server (NTRS)

Wurth, Laura; Evans, Kurt; Weber, Bart; Headrick, Sarah

2005-01-01

With environmental regulations limiting the use of volatile organic compounds, low-vapor pressure solvents have replaced traditional degreasing solvents for bond substrate preparation. When used to clean and prepare porous bond substrates such as phenolic composites, low vapor pressure solvents can penetrate deep into substrate pore networks and remain there for extended periods. Trapped solvents can interact with applied adhesives either prior to or during cure, potentially compromising bond properties. Currently, methods for characterizing solvent time-depth profiles in bond substrates are limited to bulk gravimetric or sectioning techniques. While sectioning techniques such as microtome allow construction of solvent depth profiles, their depth resolution and reliability are limited by substrate type. Sectioning techniques are particularly limited near the adhesive-substrate interface where depth resolution is further limited by adhesive-substrate hardness and, in the case of a partially cured adhesive, mechanical properties differences. Additionally, sectioning techniques cannot provide information about lateral solvent diffusion. Cross-section component mapping is an alternative method for measuring solvent migration in porous substrates that eliminates the issues associated with sectioning techniques. With cross-section mapping, the solvent-wiped substrate is sectioned perpendicular rather than parallel to the wiped surface, and the sectioned surface is analyzed for the solvent or solvent components of interest using a two-dimensional mapping or imaging technique. Solvent mapping can be performed using either direct or indirect methods. With a direct method, one or more solvent components are mapped using red or Raman spectroscopy together with a moveable sample stage and/or focal plane array detector. With an indirect method, an elemental "tag" not present in the substrate is added to the solvent before the substrate is wiped. Following cross sectioning, the tag element can then be mapped by its characteristic x-ray emission using either x-ray fluorescence, or electron-beam energy-and wavelength-dispersive x-ray spectrometry. The direct mapping techniques avoid issues of different diffusion or migration rates of solvents and elemental tags, while the indirect techniques avoid spectral resolution issues in cases where solvents and substrates have adjacent or overlapping peaks. In this study, cross-section component indirect mapping is being evaluated as a method for measuring migration of d-limonene based solvents in glass-cloth phenolic composite (GCP) prior to and during subsequent bonding and epoxy adhesive cure.

Influence of movable test section elements configuration on its drag and flow field uniformity at transonic speeds

NASA Astrophysics Data System (ADS)

Glazkov, S. A.; Gorbushin, A. R.; Osipova, S. L.; Semenov, A. V.

2016-10-01

The report describes the results of flow field experimental research in TsAGI T-128 transonic wind tunnel. During the tests Mach number, stagnation pressure, test section wall perforation ratio, angles between the test section panels and mixing chamber flaps varied. Based on the test results one determined corrections to the free-stream Mach number related to the flow speed difference in the model location and in the zone of static pressure measurement on the test section walls, nonuniformity of the longitudinal velocity component in the model location, optimal position of the movable test section elements to provide flow field uniformity in the test section and minimize the test leg drag.

Coach simplified structure modeling and optimization study based on the PBM method

NASA Astrophysics Data System (ADS)

Zhang, Miaoli; Ren, Jindong; Yin, Ying; Du, Jian

2016-09-01

For the coach industry, rapid modeling and efficient optimization methods are desirable for structure modeling and optimization based on simplified structures, especially for use early in the concept phase and with capabilities of accurately expressing the mechanical properties of structure and with flexible section forms. However, the present dimension-based methods cannot easily meet these requirements. To achieve these goals, the property-based modeling (PBM) beam modeling method is studied based on the PBM theory and in conjunction with the characteristics of coach structure of taking beam as the main component. For a beam component of concrete length, its mechanical characteristics are primarily affected by the section properties. Four section parameters are adopted to describe the mechanical properties of a beam, including the section area, the principal moments of inertia about the two principal axles, and the torsion constant of the section. Based on the equivalent stiffness strategy, expressions for the above section parameters are derived, and the PBM beam element is implemented in HyperMesh software. A case is realized using this method, in which the structure of a passenger coach is simplified. The model precision is validated by comparing the basic performance of the total structure with that of the original structure, including the bending and torsion stiffness and the first-order bending and torsional modal frequencies. Sensitivity analysis is conducted to choose design variables. The optimal Latin hypercube experiment design is adopted to sample the test points, and polynomial response surfaces are used to fit these points. To improve the bending and torsion stiffness and the first-order torsional frequency and taking the allowable maximum stresses of the braking and left turning conditions as constraints, the multi-objective optimization of the structure is conducted using the NSGA-II genetic algorithm on the ISIGHT platform. The result of the Pareto solution set is acquired, and the selection strategy of the final solution is discussed. The case study demonstrates that the mechanical performances of the structure can be well-modeled and simulated by PBM beam. Because of the merits of fewer parameters and convenience of use, this method is suitable to be applied in the concept stage. Another merit is that the optimization results are the requirements for the mechanical performance of the beam section instead of those of the shape and dimensions, bringing flexibility to the succeeding design.

Visualization and Semiquantitative Study of the Distribution of Major Components in Wheat Straw in Mesoscopic Scale using Fourier Transform Infrared Microspectroscopic Imaging.

PubMed

Yang, Zengling; Mei, Jiaqi; Liu, Zhiqiang; Huang, Guangqun; Huang, Guan; Han, Lujia

2018-06-19

Understanding the biochemical heterogeneity of plant tissue linked to crop straw anatomy is attractive to plant researchers and researchers in the field of biomass refinery. This study provides an in situ analysis and semiquantitative visualization of major components distribution in internodal transverse sections of wheat straw based on Fourier transform infrared (FTIR) microspectroscopic imaging, with a fast non-negativity-constrained least squares (fast NNLS) fitting. This paper investigates changes in biochemical components of tissue during stages of elongation, booting, heading, flowering, grain-filling, milk-ripening, dough, and full-ripening. Visualization analysis was carried out with reference spectra for five components (microcrystalline cellulose, xylan, lignin, pectin, and starch) of wheat straw. Our result showed that (a) the cellulose and lignin distribution is consistent with that from tissue-dyeing with safranin O-fast green and (b) the distribution of cellulose, lignin, and starch is consistent with chemical images for characteristic wavelength at 1432, 1507, and 987 cm -1 , respectively, showing no interference from the other components analyzed. With the validation from biochemical images using characteristic wavelength and tissue-dyeing techniques, further semiquantitative analysis in local tissues based on fast NNLS was carried out, and the result showed that (a) the contents of cellulose in various tissues are very different, with most in parenchyma tissue and least in the epidermis and (b) during plant development, the fluctuation of each component in tissues follows nearly the same trend, especially within vascular bundles and parenchyma tissue. Thus, FTIR microspectroscopic imaging combined with suitable chemometric methods can be successfully applied to study chemical distributions within the internodes transverse sections of wheat straw, providing semiquantitative chemical information.

34 CFR 200.28 - Schoolwide program components.

Code of Federal Regulations, 2010 CFR

2010-07-01

... provide information on, and to improve, the achievement of individual students and the overall... literacy services, to increase parental involvement in accordance with sections 1118(c) through (f) and... identified on a timely basis; and (2) Provide sufficient information on which to base effective assistance to...

34 CFR 200.28 - Schoolwide program components.

Code of Federal Regulations, 2011 CFR

2011-07-01

... provide information on, and to improve, the achievement of individual students and the overall... literacy services, to increase parental involvement in accordance with sections 1118(c) through (f) and... identified on a timely basis; and (2) Provide sufficient information on which to base effective assistance to...

34 CFR 200.28 - Schoolwide program components.

Code of Federal Regulations, 2012 CFR

2012-07-01

... provide information on, and to improve, the achievement of individual students and the overall... literacy services, to increase parental involvement in accordance with sections 1118(c) through (f) and... identified on a timely basis; and (2) Provide sufficient information on which to base effective assistance to...

34 CFR 200.28 - Schoolwide program components.

Code of Federal Regulations, 2014 CFR

2014-07-01

... provide information on, and to improve, the achievement of individual students and the overall... literacy services, to increase parental involvement in accordance with sections 1118(c) through (f) and... identified on a timely basis; and (2) Provide sufficient information on which to base effective assistance to...

34 CFR 200.28 - Schoolwide program components.

Code of Federal Regulations, 2013 CFR

2013-07-01

... provide information on, and to improve, the achievement of individual students and the overall... literacy services, to increase parental involvement in accordance with sections 1118(c) through (f) and... identified on a timely basis; and (2) Provide sufficient information on which to base effective assistance to...

47 CFR 65.300 - Calculations of the components and weights of the cost of capital.

Code of Federal Regulations, 2011 CFR

2011-10-01

... indexed revenue threshold as defined in § 32.9000. The calculations shall be based on data reported to the... treated as “zero cost” sources of financing in section 450 and subpart G of this part 65. Specifically...

47 CFR 65.300 - Calculations of the components and weights of the cost of capital.

Code of Federal Regulations, 2010 CFR

2010-10-01

... indexed revenue threshold as defined in § 32.9000. The calculations shall be based on data reported to the... treated as “zero cost” sources of financing in section 450 and subpart G of this part 65. Specifically...

Revisit of cosmic ray antiprotons from dark matter annihilation with updated constraints on the background model from AMS-02 and collider data

NASA Astrophysics Data System (ADS)

Cui, Ming-Yang; Pan, Xu; Yuan, Qiang; Fan, Yi-Zhong; Zong, Hong-Shi

2018-06-01

We study the cosmic ray antiprotons with updated constraints on the propagation, proton injection, and solar modulation parameters based on the newest AMS-02 data near the Earth and Voyager data in the local interstellar space, and on the cross section of antiproton production due to proton-proton collisions based on new collider data. We use a Bayesian approach to properly consider the uncertainties of the model predictions of both the background and the dark matter (DM) annihilation components of antiprotons. We find that including an extra component of antiprotons from the annihilation of DM particles into a pair of quarks can improve the fit to the AMS-02 antiproton data considerably. The favored mass of DM particles is about 60~100 GeV, and the annihilation cross section is just at the level of the thermal production of DM (langleσvrangle ~ O(10‑26) cm3 s‑1).

Component-based model to predict aerodynamic noise from high-speed train pantographs

NASA Astrophysics Data System (ADS)

Latorre Iglesias, E.; Thompson, D. J.; Smith, M. G.

2017-04-01

At typical speeds of modern high-speed trains the aerodynamic noise produced by the airflow over the pantograph is a significant source of noise. Although numerical models can be used to predict this they are still very computationally intensive. A semi-empirical component-based prediction model is proposed to predict the aerodynamic noise from train pantographs. The pantograph is approximated as an assembly of cylinders and bars with particular cross-sections. An empirical database is used to obtain the coefficients of the model to account for various factors: incident flow speed, diameter, cross-sectional shape, yaw angle, rounded edges, length-to-width ratio, incoming turbulence and directivity. The overall noise from the pantograph is obtained as the incoherent sum of the predicted noise from the different pantograph struts. The model is validated using available wind tunnel noise measurements of two full-size pantographs. The results show the potential of the semi-empirical model to be used as a rapid tool to predict aerodynamic noise from train pantographs.

Doppler Broadening and its Contribution to Compton Energy-Absorption Cross Sections: An Analysis of the Compton Component in Terms of Mass-Energy Absorption Coefficient

NASA Astrophysics Data System (ADS)

Rao, D. V.; Takeda, T.; Itai, Y.; Akatsuka, T.; Cesareo, R.; Brunetti, A.; Gigante, G. E.

2002-09-01

Compton energy absorption cross sections are calculated using the formulas based on a relativistic impulse approximation to assess the contribution of Doppler broadening and to examine the Compton profile literature and explore what, if any, effect our knowledge of this line broadening has on the Compton component in terms of mass-energy absorption coefficient. Compton energy-absorption cross sections are evaluated for all elements, Z=1-100, and for photon energies 1 keV-100 MeV. Using these cross sections, the Compton component of the mass-energy absorption coefficient is derived in the energy region from 1 keV to 1 MeV for all the elements Z=1-100. The electron momentum prior to the scattering event should cause a Doppler broadening of the Compton line. The momentum resolution function is evaluated in terms of incident and scattered photon energy and scattering angle. The overall momentum resolution of each contribution is estimated for x-ray and γ-ray energies of experimental interest in the angular region 1°-180°. Also estimated is the Compton broadening using nonrelativistic formula in the angular region 1°-180°, for 17.44, 22.1, 58.83, and 60 keV photons for a few elements (H, C, N, O, P, S, K, and Ca) of biological importance.

Microscopic neural image registration based on the structure of mitochondria

NASA Astrophysics Data System (ADS)

Cao, Huiwen; Han, Hua; Rao, Qiang; Xiao, Chi; Chen, Xi

2017-02-01

Microscopic image registration is a key component of the neural structure reconstruction with serial sections of neural tissue. The goal of microscopic neural image registration is to recover the 3D continuity and geometrical properties of specimen. During image registration, various distortions need to be corrected, including image rotation, translation, tissue deformation et.al, which come from the procedure of sample cutting, staining and imaging. Furthermore, there is only certain similarity between adjacent sections, and the degree of similarity depends on local structure of the tissue and the thickness of the sections. These factors make the microscopic neural image registration a challenging problem. To tackle the difficulty of corresponding landmarks extraction, we introduce a novel image registration method for Scanning Electron Microscopy (SEM) images of serial neural tissue sections based on the structure of mitochondria. The ellipsoidal shape of mitochondria ensures that the same mitochondria has similar shape between adjacent sections, and its characteristic of broad distribution in the neural tissue guarantees that landmarks based on the mitochondria distributed widely in the image. The proposed image registration method contains three parts: landmarks extraction between adjacent sections, corresponding landmarks matching and image deformation based on the correspondences. We demonstrate the performance of our method with SEM images of drosophila brain.

A microcontroller-based microwave free-space measurement system for permittivity determination of lossy liquid materials.

PubMed

Hasar, U C

2009-05-01

A microcontroller-based noncontact and nondestructive microwave free-space measurement system for real-time and dynamic determination of complex permittivity of lossy liquid materials has been proposed. The system is comprised of two main sections--microwave and electronic. While the microwave section provides for measuring only the amplitudes of reflection coefficients, the electronic section processes these data and determines the complex permittivity using a general purpose microcontroller. The proposed method eliminates elaborate liquid sample holder preparation and only requires microwave components to perform reflection measurements from one side of the holder. In addition, it explicitly determines the permittivity of lossy liquid samples from reflection measurements at different frequencies without any knowledge on sample thickness. In order to reduce systematic errors in the system, we propose a simple calibration technique, which employs simple and readily available standards. The measurement system can be a good candidate for industrial-based applications.

Tire deflation device

DOEpatents

Barker, Stacey G [Idaho Falls, ID

2010-01-05

A tire deflation device includes (1) a component having a plurality of bores, (2) a plurality of spikes removably insertable into the plurality of bores and (3) a keeper within each among the plurality of bores, the keeper being configured to contact a sidewall surface of a spike among the plurality of spikes and to exert force upon the sidewall surface. In an embodiment, the tire deflation device includes (a) a component including a bore in a material, the bore including a receiving region, a sidewall surface and a base surface, (b) a channel extending from the sidewall surface into the material, (c) a keeper having a first section housed within the channel and a second section which extends past the sidewall surface into the receiving region, and (d) a spike removably insertable into the bore.

Improving cancer treatment with cyclotron produced radionuclides

DOE Office of Scientific and Technical Information (OSTI.GOV)

Larson, S.M. Finn, R.D.

1992-08-04

This report describes the author's continuing long term goal of promoting nuclear medicine applications by improving the scientific basis for tumor diagnosis treatment and treatment follow-up based on the use of cyclotron produced radiotracers in oncology. The program has 3 interactive components: Radiochemistry /Cyclotron; Pharmacology; and Immunology. An essential strategy is as follows: novel radionuclides and radiotracers developed in the Radiochemistry/Cyclotron section under the DOE grant during the 1989--1992 grant period, will be employed in the Pharmacology and Immunology sections of the DOE grant during the 1992--1995 grant period. The development of novel radionuclides and tracers is of course usefulmore » in and of itself, but their utility is greatly enhanced by the interaction with the immunology and pharmacology components of the program.« less

Peace Corps Language Training Curriculum.

ERIC Educational Resources Information Center

Peace Corps, Washington, DC. Information Collection and Exchange Div.

This competency-based curriculum in foreign language learning for Peace Corps volunteers is designed for beginning learners and stresses listening and speaking skills. The curriculum contains the following components: an initial Scope and Sequence chart; three sections on activities (General, Grammar, and Listening), 14 topic area units (the core…

Droplet microfluidics for single-cell analysis.

PubMed

Brouzes, Eric

2012-01-01

This book chapter aims at providing an overview of all the aspects and procedures needed to develop a droplet-based workflow for single-cell analysis (see Fig. 10.1). The surfactant system used to stabilize droplets is a critical component of droplet microfluidics; its properties define the type of droplet-based assays and workflows that can be developed. The scope of this book chapter is limited to fluorinated surfactant systems that have proved to generate extremely stable droplets and allow to easily retrieve the encapsulated material. The formulation section discusses how the experimental parameters influence the choice of the surfactant system to use. The circuit design section presents recipes to design and integrate different droplet modules into a whole assay. The fabrication section describes the manufacturing of microfluidic chip including the surface treatment which is pivotal in droplet microfluidics. Finally, the last section reviews the experimental setup for fluorescence detection with an emphasis on cell injection and incubation.

47 CFR 25.254 - Special requirements for ancillary terrestrial components operating in the 1610-1626.5 MHz/2483.5...

Code of Federal Regulations, 2012 CFR

2012-10-01

...: The preceding rules of § 25.254 are based on cdma2000 and IS-95 system architecture. To the extent that a Big LEO MSS licensee is able to demonstrate that the use of different system architectures would... section, an MSS licensee is permitted to apply for ATC authorization based on another system architecture...

47 CFR 25.254 - Special requirements for ancillary terrestrial components operating in the 1610-1626.5 MHz/2483.5...

Code of Federal Regulations, 2011 CFR

2011-10-01

...: The preceding rules of § 25.254 are based on cdma2000 and IS-95 system architecture. To the extent that a Big LEO MSS licensee is able to demonstrate that the use of different system architectures would... section, an MSS licensee is permitted to apply for ATC authorization based on another system architecture...

Development and Factor Analysis of the Protective Factors Index: A Report Card Section Related to the Work of School Counselors

ERIC Educational Resources Information Center

Bass, Gwen; Lee, Ji Hee; Wells, Craig; Carey, John C.; Lee, Sangmin

2015-01-01

The scale development and exploratory and confirmatory factor analyses of the Protective Factor Index (PFI) is described. The PFI is a 13-item component of elementary students' report cards that replaces typical items associated with student behavior. The PFI is based on the Construct-Based Approach (CBA) to school counseling, which proposes that…

Evaluating Usability of Radiology Information Systems in Hospitals of Tabriz University of Medical Sciences.

PubMed

Rezaei-Hachesu, Peyman; Pesianian, Esmaeil; Mohammadian, Mohsen

2016-02-01

Radiology information system (RIS) in order to reduce workload and improve the quality of services must be well-designed. Heuristic evaluation is one of the methods that understand usability problems with the least time, cost and resources. The aim of present study is to evaluate the usability of RISs in hospitals. This is a cross-sectional descriptive study (2015) that uses heuristic evaluation method to evaluate the usability of RIS used in 3 hospitals of Tabriz city. The data are collected using a standard checklist based on 13 principles of Nielsen Heuristic evaluation method. Usability of RISs was investigated based on the number of components observed from Nielsen principles and problems of usability based on the number of non-observed components as well as non-existent or unrecognizable components. by evaluation of RISs in each of the hospitals 1, 2 and 3, total numbers of observed components were obtained as 173, 202 and 196, respectively. It was concluded that the usability of RISs in the studied population, on average and with observing 190 components of the 291 components related to the 13 principles of Nielsen is 65.41 %. Furthermore, problems of usability were obtained as 26.35%. The established and visible nature of some components such as response time of application, visual feedbacks, colors, view and design and arrangement of software objects cause more attention to these components as principal components in designing UI software. Also, incorrect analysis before system design leads to a lack of attention to secondary needs like Help software and security issues.

NEuclid: a long-range tilt-immune homodyne interferometer

NASA Astrophysics Data System (ADS)

Bradshaw, M. J.; Speake, C. C.

2017-11-01

The new Easy to Use Compact Laser Interferometric Device (nEUCLID) is a polarisation-based homodyne interferometer with substantially unequal arms that is tolerant to target mirror tilt. The design has no active components, uses standard optical components of 25 mm diameter, has a working distance of 706 mm and a reference arm-length of 21 mm. nEUCLID optics have a footprint of 210 x 190 x 180 mm, and has a tolerance to target mirror tilt of +/- 0.5 degrees, made possible by a novel new retro-reflector design [1]. nEUCLID was built to a set of specifications laid down by Airbus Defence and Space, who required a lowmass, low-power device to measure displacement with nanometre accuracy for space applications. At the University of Birmingham we have previously built a smaller, more compact tilt-insensitive homodyne interferometer - the EUCLID [2, 3, 4] - which has a working distance of 6 mm, a working range of +/- 3 mm, and a tilt range of +/- 1° [2]. We created a new optical design to allow a much larger working distance to be achieved (as discussed in Section II) and used this in a new interferometer - the nEUCLID. Section II describes the interferometer in detail; how nEUCLID is tilt insensitive, and the optical configuration. Section III states the design specifications from Airbus Defence and Space and the components used in the final design. The output interference pattern from nEUCLID, and how it has been corrected with a meniscus lens, is also discussed. In Section IV we discuss the results demonstrating the tilt immunity range, and the sensitivity of the device. Section V describes several potential applications of nEUCLID, and Section VI draws together our conclusions.

CBE: The Right Angle for Learning.

ERIC Educational Resources Information Center

Seitz, Fred

Designed for instructors at Beaufort Technical College (BTC) in South Carolina, this handbook provides a brief guide to competency-based education (CBE) and to the available resources at the college for assistance. Section 1 offers introductory comments on the concept of quality control and the five basic components of educational quality control.…

75 FR 9434 - Civil Rights Division, Disability Rights Section; Agency Information Collection Activities Under...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-02

... Act of 1973 Discrimination Complaint Form. The Department of Justice, Civil Rights Division... Act of 1973 Discrimination Complaint Form. (3) The agency form number and applicable component of the...: Individuals alleging discrimination by public entities based on disability. Under title II of the Americans...

Attracting Clients to Service-Oriented Programs.

ERIC Educational Resources Information Center

Disney, Diane M.

One of a series of manuals developed by the Home and Community-Based Career Education Project, the outreach component publication describes how the project went about attracting clients for its adult vocational counseling services. Sections include: creating a publicity campaign, using an advertising agency, creating products for the mass media,…

The Creative Curriculum for Infants and Toddlers.

ERIC Educational Resources Information Center

Dombro, Amy Laura; And Others

Stemming from the core idea that infant and toddler care should be based on building relationships, this curriculum provides a foundation for staff development. Section 1, "Why a Curriculum for Infants and Toddlers?" examines key quality indicators; discusses curriculum components; describes how to use it to make decisions throughout a…

Modeling Hospital Discharge and Placement Decision Making: Whither the Elderly.

ERIC Educational Resources Information Center

Clark, William F.; Pelham, Anabel O.

This paper examines the hospital discharge decision making process for elderly patients, based on observations of the operations of a long term care agency, the California Multipurpose Senior Services Project. The analysis is divided into four components: actors, factors, processes, and strategy critique. The first section discusses the major…

Coherent and incoherent ultrasound backscatter from cell aggregates.

PubMed

de Monchy, Romain; Destrempes, François; Saha, Ratan K; Cloutier, Guy; Franceschini, Emilie

2016-09-01

The effective medium theory (EMT) was recently developed to model the ultrasound backscatter from aggregating red blood cells [Franceschini, Metzger, and Cloutier, IEEE Trans. Ultrason. Ferroelectr. Freq. Control 58, 2668-2679 (2011)]. The EMT assumes that aggregates can be treated as homogeneous effective scatterers, which have effective properties determined by the aggregate compactness and the acoustical characteristics of the cells and the surrounding medium. In this study, the EMT is further developed to decompose the differential backscattering cross section of a single cell aggregate into coherent and incoherent components. The coherent component corresponds to the squared norm of the average scattering amplitude from the effective scatterer, and the incoherent component considers the variance of the scattering amplitude (i.e., the mean squared norm of the fluctuation of the scattering amplitude around its mean) within the effective scatterer. A theoretical expression for the incoherent component based on the structure factor is proposed and compared with another formulation based on the Gaussian direct correlation function. This theoretical improvement is assessed using computer simulations of ultrasound backscatter from aggregating cells. The consideration of the incoherent component based on the structure factor allows us to approximate the simulations satisfactorily for a product of the wavenumber times the aggregate radius kr ag around 2.

Exploration of cellular reaction systems.

PubMed

Kirkilionis, Markus

2010-01-01

We discuss and review different ways to map cellular components and their temporal interaction with other such components to different non-spatially explicit mathematical models. The essential choices made in the literature are between discrete and continuous state spaces, between rule and event-based state updates and between deterministic and stochastic series of such updates. The temporal modelling of cellular regulatory networks (dynamic network theory) is compared with static network approaches in two first introductory sections on general network modelling. We concentrate next on deterministic rate-based dynamic regulatory networks and their derivation. In the derivation, we include methods from multiscale analysis and also look at structured large particles, here called macromolecular machines. It is clear that mass-action systems and their derivatives, i.e. networks based on enzyme kinetics, play the most dominant role in the literature. The tools to analyse cellular reaction networks are without doubt most complete for mass-action systems. We devote a long section at the end of the review to make a comprehensive review of related tools and mathematical methods. The emphasis is to show how cellular reaction networks can be analysed with the help of different associated graphs and the dissection into modules, i.e. sub-networks.

Probabalistic Risk Assessment of a Turbine Disk

NASA Astrophysics Data System (ADS)

Carter, Jace A.; Thomas, Michael; Goswami, Tarun; Fecke, Ted

Current Federal Aviation Administration (FAA) rotor design certification practices risk assessment using a probabilistic framework focused on only the life-limiting defect location of a component. This method generates conservative approximations of the operational risk. The first section of this article covers a discretization method, which allows for a transition from this relative risk to an absolute risk where the component is discretized into regions called zones. General guidelines were established for the zone-refinement process based on the stress gradient topology in order to reach risk convergence. The second section covers a risk assessment method for predicting the total fatigue life due to fatigue induced damage. The total fatigue life incorporates a dual mechanism approach including the crack initiation life and propagation life while simultaneously determining the associated initial flaw sizes. A microstructure-based model was employed to address uncertainties in material response and relate crack initiation life with crack size, while propagation life was characterized large crack growth laws. The two proposed methods were applied to a representative Inconel 718 turbine disk. The zone-based method reduces the conservative approaches, while showing effects of feature-based inspection on the risk assessment. In the fatigue damage assessment, the predicted initial crack distribution was found to be the most sensitive probabilistic parameter and can be used to establish an enhanced inspection planning.

Identification among morphologically similar Argyreia (Convolvulaceae) based on leaf anatomy and phenetic analyses.

PubMed

Traiperm, Paweena; Chow, Janene; Nopun, Possathorn; Staples, G; Swangpol, Sasivimon C

2017-12-01

The genus Argyreia Lour. is one of the species-rich Asian genera in the family Convolvulaceae. Several species complexes were recognized in which taxon delimitation was imprecise, especially when examining herbarium materials without fully developed open flowers. The main goal of this study is to investigate and describe leaf anatomy for some morphologically similar Argyreia using epidermal peeling, leaf and petiole transverse sections, and scanning electron microscopy. Phenetic analyses including cluster analysis and principal component analysis were used to investigate the similarity of these morpho-types. Anatomical differences observed between the morpho-types include epidermal cell walls and the trichome types on the leaf epidermis. Additional differences in the leaf and petiole transverse sections include the epidermal cell shape of the adaxial leaf blade, the leaf margins, and the petiole transverse sectional outline. The phenogram from cluster analysis using the UPGMA method represented four groups with an R value of 0.87. Moreover, the important quantitative and qualitative leaf anatomical traits of the four groups were confirmed by the principal component analysis of the first two components. The results from phenetic analyses confirmed the anatomical differentiation between the morpho-types. Leaf anatomical features regarded as particularly informative for morpho-type differentiation can be used to supplement macro morphological identification.

LUTE telescope structural design

NASA Technical Reports Server (NTRS)

Ruthven, Gregory

1993-01-01

The major objective of the Lunar Ultraviolet Transit Experiment (LUTE) Telescope Structural Design Study was to investigate the feasibility of designing an ultralightweight 1-m aperture system within optical performance requirements and mass budget constraints. This study uses the results from our previous studies on LUTE as a basis for further developing the LUTE structural architecture. After summarizing our results in Section 2, Section 3 begins with the overall logic we used to determine which telescope 'structural form' should be adopted for further analysis and weight estimates. Specific telescope component analysis showing calculated fundamental frequencies and how they compare with our derived requirements are included. 'First-order' component stress analyses to ensure telescope optical and structural component (i.e. mirrors & main bulkhead) weights are realistic are presented. Layouts of both the primary and tertiary mirrors showing dimensions that are consistent with both our weight and frequency calculations also form part of Section 3. Section 4 presents our calculated values for the predicted thermally induced primary-to-secondary mirror despace motion due to the large temperature range over which LUTE must operate. Two different telescope design approaches (one which utilizes fused quartz metering rods and one which assumes the entire telescope is fabricated from beryllium) are considered in this analysis. We bound the secondary mirror focus mechanism range (in despace) based on these two telescope configurations. In Section 5 we show our overall design of the UVTA (Ultraviolet Telescope Assembly) via an 'exploded view' of the sub-system. The 'exploded view' is annotated to help aid in the understanding of each sub-assembly. We also include a two view layout of the UVTA from which telescope and telescope component dimensions can be measured. We conclude our study with a set of recommendations not only with respect to the LUTE structural architecture but also on other topics related to the overall feasibility of the LUTE telescope sub-system.

Developing anti-tobacco messages for Australian Aboriginal and Torres Strait Islander peoples: evidence from a national cross-sectional survey.

PubMed

Gould, Gillian S; Watt, Kerrianne; Stevenson, Leah; McEwen, Andy; Cadet-James, Yvonne; Clough, Alan R

2014-03-13

Smoking rates in Australian Aboriginal and Torres Strait Islander peoples remain high, with limited impact of government measures for many subgroups. The aim of this cross-sectional study was to investigate differences in organisational practice for developing anti-tobacco messages for these target populations. Telephone interviews were conducted with 47 organisation representatives using a structured questionnaire based on health communication and health promotion frameworks. Responses were coded into phases of message development, message types (educational, threat, positive or advocacy), target groups, message recommendations, and evaluations undertaken. Cultural sensitivity for message development was divided into surface structure (use of images, language, demographics) and deep structure (use of socio-cultural values). A categorical principal component analysis explored the key dimensions of the findings and their component relationships. Among organisations interviewed, a community-orientated, bottom-up approach for developing anti-tobacco messages was reported by 47% (n=24); 55% based message development on a theoretical framework; 87% used a positive benefit appeal; 38% used threat messages. More Aboriginal Medical Services (AMSs) targeted youth (p<0.005) and advised smokers to quit (p<0.05) than other types of organisations. AMSs were significantly more likely to report using deep structure in tailoring messages compared with non-government (p<0.05) and government organisations (p<0.05). Organisations that were oriented to the general population were more likely to evaluate their programs (p<0.05). A two-dimensional non-linear principal component analysis extracted components interpreted as "cultural understanding" (bottom-up, community-based approaches, deep structures) and "rigour" (theoretical frameworks, and planned/completed evaluations), and accounted for 53% of the variability in the data. Message features, associated with successful campaigns in other populations, are starting to be used for Aboriginal and Torres Strait Islander peoples. A model is proposed to facilitate the development of targeted anti-tobacco messages for Aboriginal and Torres Strait Islander peoples. Organisations could consider incorporating both components of cultural understanding-rigour to enable the growth of evidence-based practice.

Developing anti-tobacco messages for Australian Aboriginal and Torres Strait Islander peoples: evidence from a national cross-sectional survey

PubMed Central

2014-01-01

Background Smoking rates in Australian Aboriginal and Torres Strait Islander peoples remain high, with limited impact of government measures for many subgroups. The aim of this cross-sectional study was to investigate differences in organisational practice for developing anti-tobacco messages for these target populations. Methods Telephone interviews were conducted with 47 organisation representatives using a structured questionnaire based on health communication and health promotion frameworks. Responses were coded into phases of message development, message types (educational, threat, positive or advocacy), target groups, message recommendations, and evaluations undertaken. Cultural sensitivity for message development was divided into surface structure (use of images, language, demographics) and deep structure (use of socio-cultural values). A categorical principal component analysis explored the key dimensions of the findings and their component relationships. Results Among organisations interviewed, a community-orientated, bottom-up approach for developing anti-tobacco messages was reported by 47% (n = 24); 55% based message development on a theoretical framework; 87% used a positive benefit appeal; 38% used threat messages. More Aboriginal Medical Services (AMSs) targeted youth (p < 0.005) and advised smokers to quit (p < 0.05) than other types of organisations. AMSs were significantly more likely to report using deep structure in tailoring messages compared with non-government (p < 0.05) and government organisations (p < 0.05). Organisations that were oriented to the general population were more likely to evaluate their programs (p < 0.05). A two-dimensional non-linear principal component analysis extracted components interpreted as “cultural understanding” (bottom-up, community-based approaches, deep structures) and “rigour” (theoretical frameworks, and planned/completed evaluations), and accounted for 53% of the variability in the data. Conclusion Message features, associated with successful campaigns in other populations, are starting to be used for Aboriginal and Torres Strait Islander peoples. A model is proposed to facilitate the development of targeted anti-tobacco messages for Aboriginal and Torres Strait Islander peoples. Organisations could consider incorporating both components of cultural understanding-rigour to enable the growth of evidence-based practice. PMID:24625235

Quantifying behavioural determinants relating to health professional reporting of medication errors: a cross-sectional survey using the Theoretical Domains Framework.

PubMed

Alqubaisi, Mai; Tonna, Antonella; Strath, Alison; Stewart, Derek

2016-11-01

The aims of this study were to quantify the behavioural determinants of health professional reporting of medication errors in the United Arab Emirates (UAE) and to explore any differences between respondents. A cross-sectional survey of patient-facing doctors, nurses and pharmacists within three major hospitals of Abu Dhabi, the UAE. An online questionnaire was developed based on the Theoretical Domains Framework (TDF, a framework of behaviour change theories). Principal component analysis (PCA) was used to identify components and internal reliability determined. Ethical approval was obtained from a UK university and all hospital ethics committees. Two hundred and ninety-four responses were received. Questionnaire items clustered into six components of knowledge and skills, feedback and support, action and impact, motivation, effort and emotions. Respondents generally gave positive responses for knowledge and skills, feedback and support and action and impact components. Responses were more neutral for the motivation and effort components. In terms of emotions, the component with the most negative scores, there were significant differences in terms of years registered as health professional (those registered longest most positive, p = 0.002) and age (older most positive, p < 0.001) with no differences for gender and health profession. Emotional-related issues are the dominant barrier to reporting and are common to all professions. There is a need to develop, test and implement an intervention to impact health professionals' emotions. Such an intervention should focus on evidence-based behaviour change techniques of reducing negative emotions, focusing on emotional consequences and providing social support. • This research used the Theoretical Domains Framework to quantify the behavioural determinants of health professional reporting of medication errors. • Questionnaire items relating to emotions surrounding reporting generated the most negative responses with significant differences in terms of years registered as health professional (those registered longest most positive) and age (older most positive) with no differences for gender and health profession. • Interventions based on behaviour change techniques mapped to emotions should be prioritised for development.

Improving cancer treatment with cyclotron produced radionuclides. Comprehensive progress report, February 1, 1990--January 31, 1993

DOE Office of Scientific and Technical Information (OSTI.GOV)

Larson, S.M. Finn, R.D.

1992-08-04

This report describes the author`s continuing long term goal of promoting nuclear medicine applications by improving the scientific basis for tumor diagnosis treatment and treatment follow-up based on the use of cyclotron produced radiotracers in oncology. The program has 3 interactive components: Radiochemistry /Cyclotron; Pharmacology; and Immunology. An essential strategy is as follows: novel radionuclides and radiotracers developed in the Radiochemistry/Cyclotron section under the DOE grant during the 1989--1992 grant period, will be employed in the Pharmacology and Immunology sections of the DOE grant during the 1992--1995 grant period. The development of novel radionuclides and tracers is of course usefulmore » in and of itself, but their utility is greatly enhanced by the interaction with the immunology and pharmacology components of the program.« less

Behaviour and design considerations for continuous flow closed-open-closed liquid microchannels.

PubMed

Melin, Jessica; van der Wijngaart, Wouter; Stemme, Göran

2005-06-01

This paper introduces a method of combining open and closed microchannels in a single component in a novel way which couples the benefits of both open and closed microfluidic systems and introduces interesting on-chip microfluidic behaviour. Fluid behaviour in such a component, based on continuous pressure driven flow and surface tension, is discussed in terms of cross sectional flow behaviour, robustness, flow-pressure performance, and its application to microfluidic interfacing. The closed-open-closed microchannel possesses the versatility of upstream and downstream closed microfluidics along with open fluidic direct access. The device has the advantage of eliminating gas bubbles present upstream when these enter the open channel section. The unique behaviour of this device opens the door to applications including direct liquid sample interfacing without the need for additional and bulky sample tubing.

Views of Family Medicine Trainees of a Teaching Hospital in Riyadh regarding their Hospital Rotations: A Qualitative Study.

PubMed

Alquaiz, Aljohara M; Abdulghani, Hamza M; Karim, Syed Irfan; Qureshi, Riaz

2013-01-01

To explore Family Medicine Trainees views regarding the hospital component of their Family Medicine (FM) training program. This is a qualitative focus group discussion based study. Thirteen trainees, eight from final year of FM training program and five from third year of the same program participated in the study. The structure for discussion included a previously distributed and completed questionnaire that included three sections. The first section was evaluation of the satisfaction of trainees with the different hospital specialties rotations. The second section related to reasons for rating the different rotations as excellent and very good. The third section related to deficiencies in training for those rotations which received a score of 3-5. The items in the questionnaire were utilized in the focus group discussion. Two facilitators who were investigators facilitated the discussion. The data was qualitatively analyzed to identify emergent themes and subthemes that described the trainees' views. The trainees highlighted the following views: Teaching in the hospital component is not relevant to the needs of Family Medicine trainees. Duration of the hospital posts should be reviewed. Emphasis should be on out-patient clinics rather than in-patient. More emphasis must be given to procedural skills, minor surgery and teaching in clinical contexts. Hospital training component of the Family Medicine training program should be reviewed, as the structure and its implementation doesn't reflect the views of trainees regarding its relevance to their day to day practice.

Gas-absorption process

DOEpatents

Stephenson, Michael J.; Eby, Robert S.

1978-01-01

This invention is an improved gas-absorption process for the recovery of a desired component from a feed-gas mixture containing the same. In the preferred form of the invention, the process operations are conducted in a closed-loop system including a gas-liquid contacting column having upper, intermediate, and lower contacting zones. A liquid absorbent for the desired component is circulated through the loop, being passed downwardly through the column, regenerated, withdrawn from a reboiler, and then recycled to the column. A novel technique is employed to concentrate the desired component in a narrow section of the intermediate zone. This technique comprises maintaining the temperature of the liquid-phase input to the intermediate zone at a sufficiently lower value than that of the gas-phase input to the zone to effect condensation of a major part of the absorbent-vapor upflow to the section. This establishes a steep temperature gradient in the section. The stripping factors below this section are selected to ensure that virtually all of the gases in the downflowing absorbent from the section are desorbed. The stripping factors above the section are selected to ensure re-dissolution of the desired component but not the less-soluble diluent gases. As a result, a peak concentration of the desired component is established in the section, and gas rich in that component can be withdrawn therefrom. The new process provides important advantages. The chief advantage is that the process operations can be conducted in a single column in which the contacting zones operate at essentially the same pressure.

40 CFR 141.720 - Inactivation toolbox components.

Code of Federal Regulations, 2013 CFR

2013-07-01

... between the indicated values: Log credit = (0.0397 × (1.09757)Temp) × CT. (c) Site-specific study. The... this section on a site-specific basis. The State must base this approval on a site-specific study a... in this table are applicable only to post-filter applications of UV in filtered systems and to...

40 CFR 141.720 - Inactivation toolbox components.

Code of Federal Regulations, 2010 CFR

2010-07-01

... between the indicated values: Log credit = (0.0397 × (1.09757)Temp) × CT. (c) Site-specific study. The... this section on a site-specific basis. The State must base this approval on a site-specific study a... in this table are applicable only to post-filter applications of UV in filtered systems and to...

40 CFR 141.720 - Inactivation toolbox components.

Code of Federal Regulations, 2011 CFR

2011-07-01

... between the indicated values: Log credit = (0.0397 × (1.09757)Temp) × CT. (c) Site-specific study. The... this section on a site-specific basis. The State must base this approval on a site-specific study a... in this table are applicable only to post-filter applications of UV in filtered systems and to...

40 CFR 141.720 - Inactivation toolbox components.

Code of Federal Regulations, 2012 CFR

2012-07-01

... between the indicated values: Log credit = (0.0397 × (1.09757)Temp) × CT. (c) Site-specific study. The... this section on a site-specific basis. The State must base this approval on a site-specific study a... in this table are applicable only to post-filter applications of UV in filtered systems and to...

"Fitness Assessment": Recommendations for an Enjoyable Student Experience

ERIC Educational Resources Information Center

Phillips, Sharon R.; Marttinen, Risto; Mercier, Kevin

2017-01-01

Fitness assessment can be an important and useful component of physical education. This article discusses how to avoid the pitfalls that lead to negative student experiences with fitness assessment and presents research-based suggestions for creating a positive experience for all students. A section to help teachers understand how to use fitness…

VESL for Heating and Air Conditioning: A Competency-based Curriculum Guide. Project OSCAER.

ERIC Educational Resources Information Center

Lopez-Valadez, Jeanne, Ed.; Pankratz, David, Ed.

This guide is intended for vocational educators developing the vocational English as a second language (VESL) component of a course in heating and air conditioning. The introductory section examines assumptions about second language learning and instruction and VESL classes, local adaptations of the curriculum, and sample VESL lessons. The chapter…

Preparation of Professionals and Career Development for the Disabled. Section V.

ERIC Educational Resources Information Center

Sanders, Charles D.; And Others

This document contains five papers about resources, support systems, and advocacy presented at a national conference about the nonwhite disabled. The papers and authors are: (1) "A College-Based Rehabilitation Training Program for Working with the Nonwhite Disabled" (C. D. Sanders)--program components include attention to sensitivity training,…

The Comprehensive Community Career and Vocational Guidance and Counseling Model.

ERIC Educational Resources Information Center

West Virginia State Dept. of Education, Charleston. Bureau of Vocational, Technical, and Adult Education.

A model is presented which is intended to serve as a reference and provide guidelines for the establishment of community based vocational guidance and counseling programs in West Virginia. The first of six sections identifies and expands four components of the program: self-understanding, decision making, environmental awareness, and job…

Directly connected heat exchanger tube section and coolant-cooled structure

DOEpatents

Chainer, Timothy J.; Coico, Patrick A.; Graybill, David P.; Iyengar, Madhusudan K.; Kamath, Vinod; Kochuparambil, Bejoy J.; Schmidt, Roger R.; Steinke, Mark E.

2015-09-15

A method is provided for fabricating a cooling apparatus for cooling an electronics rack, which includes an air-to-liquid heat exchanger, one or more coolant-cooled structures, and a tube. The heat exchanger is associated with the electronics rack and disposed to cool air passing through the rack, includes a plurality of coolant-carrying tube sections, each tube section having a coolant inlet and outlet, one of which is coupled in fluid communication with a coolant loop to facilitate flow of coolant through the tube section. The coolant-cooled structure(s) is in thermal contact with an electronic component(s) of the rack, and facilitates transfer of heat from the component(s) to the coolant. The tube connects in fluid communication one coolant-cooled structure and the other of the coolant inlet or outlet of the one tube section, and facilitates flow of coolant directly between that coolant-carrying tube section of the heat exchanger and the coolant-cooled structure.

Directly connected heat exchanger tube section and coolant-cooled structure

DOEpatents

Chainer, Timothy J; Coico, Patrick A; Graybill, David P; Iyengar, Madhusudan K; Kamath, Vinod; Kochuparambil, Bejoy J; Schmidt, Roger R; Steinke, Mark E

2014-04-01

A cooling apparatus for an electronics rack is provided which includes an air-to-liquid heat exchanger, one or more coolant-cooled structures and a tube. The heat exchanger, which is associated with the electronics rack and disposed to cool air passing through the rack, includes a plurality of distinct, coolant-carrying tube sections, each tube section having a coolant inlet and a coolant outlet, one of which is coupled in fluid communication with a coolant loop to facilitate flow of coolant through the tube section. The coolant-cooled structure(s) is in thermal contact with an electronic component(s) of the rack, and facilitates transfer of heat from the component(s) to the coolant. The tube connects in fluid communication one coolant-cooled structure and the other of the coolant inlet or outlet of the one tube section, and facilitates flow of coolant directly between that coolant-carrying tube section of the heat exchanger and the coolant-cooled structure.

Simulation of mixture microstructures via particle packing models and their direct comparison with real mixtures

NASA Astrophysics Data System (ADS)

Gulliver, Eric A.

The objective of this thesis to identify and develop techniques providing direct comparison between simulated and real packed particle mixture microstructures containing submicron-sized particles. This entailed devising techniques for simulating powder mixtures, producing real mixtures with known powder characteristics, sectioning real mixtures, interrogating mixture cross-sections, evaluating and quantifying the mixture interrogation process and for comparing interrogation results between mixtures. A drop and roll-type particle-packing model was used to generate simulations of random mixtures. The simulated mixtures were then evaluated to establish that they were not segregated and free from gross defects. A powder processing protocol was established to provide real mixtures for direct comparison and for use in evaluating the simulation. The powder processing protocol was designed to minimize differences between measured particle size distributions and the particle size distributions in the mixture. A sectioning technique was developed that was capable of producing distortion free cross-sections of fine scale particulate mixtures. Tessellation analysis was used to interrogate mixture cross sections and statistical quality control charts were used to evaluate different types of tessellation analysis and to establish the importance of differences between simulated and real mixtures. The particle-packing program generated crescent shaped pores below large particles but realistic looking mixture microstructures otherwise. Focused ion beam milling was the only technique capable of sectioning particle compacts in a manner suitable for stereological analysis. Johnson-Mehl and Voronoi tessellation of the same cross-sections produced tessellation tiles with different the-area populations. Control charts analysis showed Johnson-Mehl tessellation measurements are superior to Voronoi tessellation measurements for detecting variations in mixture microstructure, such as altered particle-size distributions or mixture composition. Control charts based on tessellation measurements were used for direct, quantitative comparisons between real and simulated mixtures. Four sets of simulated and real mixtures were examined. Data from real mixture was matched with simulated data when the samples were well mixed and the particle size distributions and volume fractions of the components were identical. Analysis of mixture components that occupied less than approximately 10 vol% of the mixture was not practical unless the particle size of the component was extremely small and excellent quality high-resolution compositional micrographs of the real sample are available. These methods of analysis should allow future researchers to systematically evaluate and predict the impact and importance of variables such as component volume fraction and component particle size distribution as they pertain to the uniformity of powder mixture microstructures.

RHCV Telescope System Operations Manual

DTIC Science & Technology

2018-01-05

hardware and software components. Several of the components are closely coupled and rely on one-another, while others are largely independent. This...of hardware and software components. Several of the components are closely coupled and rely on one-another, while others are largely independent. This...attendant training The use cases are briefly described in separate sections, and step-by-step instructions are presented. Each section begins on a new

Social Studies Curriculum Continuum. Grades K-8.

ERIC Educational Resources Information Center

Cole, Richard, Ed.

A series of charts relating social studies skills to components for grades kindergarten through eight is presented. The document is divided into three major sections: grades kindergarten through two, three through five, and six through eight. Nine categories and related components are listed within each section: (1) content components include…

Passive heat-transfer means for nuclear reactors. [LMFBR

DOEpatents

Burelbach, J.P.

1982-06-10

An improved passive cooling arrangement is disclosed for maintaining adjacent or related components of a nuclear reactor within specified temperature differences. Specifically, heat pipes are operatively interposed between the components, with the vaporizing section of the heat pipe proximate the hot component operable to cool it and the primary condensing section of the heat pipe proximate the other and cooler component operable to heat it. Each heat pipe further has a secondary condensing section that is located outwardly beyond the reactor confinement and in a secondary heat sink, such as air ambient the containment, that is cooler than the other reactor component. By having many such heat pipes, an emergency passive cooling system is defined that is operative without electrical power.

Component-specific modeling. [jet engine hot section components

NASA Technical Reports Server (NTRS)

Mcknight, R. L.; Maffeo, R. J.; Tipton, M. T.; Weber, G.

1992-01-01

Accomplishments are described for a 3 year program to develop methodology for component-specific modeling of aircraft hot section components (turbine blades, turbine vanes, and burner liners). These accomplishments include: (1) engine thermodynamic and mission models, (2) geometry model generators, (3) remeshing, (4) specialty three-dimensional inelastic structural analysis, (5) computationally efficient solvers, (6) adaptive solution strategies, (7) engine performance parameters/component response variables decomposition and synthesis, (8) integrated software architecture and development, and (9) validation cases for software developed.

Improving Turbine Performance with Ceramic Matrix Composites

NASA Technical Reports Server (NTRS)

DiCarlo, James A.

2007-01-01

Under the new NASA Fundamental Aeronautics Program, efforts are on-going within the Supersonics Project aimed at the implementation of advanced SiC/SiC ceramic composites into hot section components of future gas turbine engines. Due to recent NASA advancements in SiC-based fibers and matrices, these composites are lighter and capable of much higher service temperatures than current metallic superalloys, which in turn will allow the engines to operate at higher efficiencies and reduced emissions. This presentation briefly reviews studies within Task 6.3.3 that are primarily aimed at developing physics-based concepts, tools, and process/property models for micro- and macro-structural design, fabrication, and lifing of SiC/SiC turbine components in general and airfoils in particular. Particular emphasis is currently being placed on understanding and modeling (1) creep effects on residual stress development within the component, (2) fiber architecture effects on key composite properties such as design strength, and (3) preform formation processes so that the optimum architectures can be implemented into complex-shaped components, such as turbine vanes and blades.

The Freight Analysis Framework Verson 4 (FAF4) - Building the FAF4 Regional Database: Data Sources and Estimation Methodologies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hwang, Ho-Ling; Hargrove, Stephanie; Chin, Shih-Miao

The Freight Analysis Framework (FAF) integrates data from a variety of sources to create a comprehensive national picture of freight movements among states and major metropolitan areas by all modes of transportation. It provides a national picture of current freight flows to, from, and within the United States, assigns the flows to the transportation network, and projects freight flow patterns into the future. The FAF4 is the fourth database of its kind, FAF1 provided estimates for truck, rail, and water tonnage for calendar year 1998, FAF2 provided a more complete picture based on the 2002 Commodity Flow Survey (CFS) andmore » FAF3 made further improvements building on the 2007 CFS. Since the first FAF effort, a number of changes in both data sources and products have taken place. The FAF4 flow matrix described in this report is used as the base-year data to forecast future freight activities, projecting shipment weights and values from year 2020 to 2045 in five-year intervals. It also provides the basis for annual estimates to the FAF4 flow matrix, aiming to provide users with the timeliest data. Furthermore, FAF4 truck freight is routed on the national highway network to produce the FAF4 network database and flow assignments for truck. This report details the data sources and methodologies applied to develop the base year 2012 FAF4 database. An overview of the FAF4 components is briefly discussed in Section 2. Effects on FAF4 from the changes in the 2012 CFS are highlighted in Section 3. Section 4 provides a general discussion on the process used in filling data gaps within the domestic CFS matrix, specifically on the estimation of CFS suppressed/unpublished cells. Over a dozen CFS OOS components of FAF4 are then addressed in Section 5 through Section 11 of this report. This includes discussions of farm-based agricultural shipments in Section 5, shipments from fishery and logging sectors in Section 6. Shipments of municipal solid wastes and debris from construction and demolition activities are covered in Section 7. Movements involving OOS industry sectors on Retail, Services, and Household/Business Moves are addressed in Section 8. Flows of OOS commodity on crude petroleum and natural gas are presented in Sections 9 and 10, respectively. Discussions regarding shipments of foreign trade, including trade with Canada/Mexico, international airfreight, and waterborne foreign trade, are then discussed in Section 11. Several appendices are also provided at the end of this report to offer additional information.« less

Effectiveness and Cost Efficiency of Different Surveillance Components for Proving Freedom and Early Detection of Disease: Bluetongue Serotype 8 in Cattle as Case Study for Belgium, France and the Netherlands.

PubMed

Welby, S; van Schaik, G; Veldhuis, A; Brouwer-Middelesch, H; Peroz, C; Santman-Berends, I M; Fourichon, C; Wever, P; Van der Stede, Y

2017-12-01

Quick detection and recovery of country's freedom status remain a constant challenge in animal health surveillance. The efficacy and cost efficiency of different surveillance components in proving the absence of infection or (early) detection of bluetongue serotype 8 in cattle populations within different countries (the Netherlands, France, Belgium) using surveillance data from years 2006 and 2007 were investigated using an adapted scenario tree model approach. First, surveillance components (sentinel, yearly cross-sectional and passive clinical reporting) within each country were evaluated in terms of efficacy for substantiating freedom of infection. Yearly cross-sectional survey and passive clinical reporting performed well within each country with sensitivity of detection values ranging around 0.99. The sentinel component had a sensitivity of detection around 0.7. Secondly, how effective the components were for (early) detection of bluetongue serotype 8 and whether syndromic surveillance on reproductive performance, milk production and mortality data available from the Netherlands and Belgium could be of added value were evaluated. Epidemic curves were used to estimate the timeliness of detection. Sensitivity analysis revealed that expected within-herd prevalence and number of herds processed were the most influential parameters for proving freedom and early detection. Looking at the assumed direct costs, although total costs were low for sentinel and passive clinical surveillance components, passive clinical surveillance together with syndromic surveillance (based on reproductive performance data) turned out most cost-efficient for the detection of bluetongue serotype 8. To conclude, for emerging or re-emerging vectorborne disease that behaves such as bluetongue serotype 8, it is recommended to use passive clinical and syndromic surveillance as early detection systems for maximum cost efficiency and sensitivity. Once an infection is detected and eradicated, cross-sectional screening for substantiating freedom of infection and sentinel for monitoring the disease evolution are recommended. © 2016 Blackwell Verlag GmbH.

A Microstructure-Based Time-Dependent Crack Growth Model for Life and Reliability Prediction of Turbopropulsion Systems

NASA Astrophysics Data System (ADS)

Chan, Kwai S.; Enright, Michael P.; Moody, Jonathan; Fitch, Simeon H. K.

2014-01-01

The objective of this investigation was to develop an innovative methodology for life and reliability prediction of hot-section components in advanced turbopropulsion systems. A set of generic microstructure-based time-dependent crack growth (TDCG) models was developed and used to assess the sources of material variability due to microstructure and material parameters such as grain size, activation energy, and crack growth threshold for TDCG. A comparison of model predictions and experimental data obtained in air and in vacuum suggests that oxidation is responsible for higher crack growth rates at high temperatures, low frequencies, and long dwell times, but oxidation can also induce higher crack growth thresholds (Δ K th or K th) under certain conditions. Using the enhanced risk analysis tool and material constants calibrated to IN 718 data, the effect of TDCG on the risk of fracture in turboengine components was demonstrated for a generic rotor design and a realistic mission profile using the DARWIN® probabilistic life-prediction code. The results of this investigation confirmed that TDCG and cycle-dependent crack growth in IN 718 can be treated by a simple summation of the crack increments over a mission. For the temperatures considered, TDCG in IN 718 can be considered as a K-controlled or a diffusion-controlled oxidation-induced degradation process. This methodology provides a pathway for evaluating microstructural effects on multiple damage modes in hot-section components.

Environmental Barrier Coating Fracture, Fatigue and High-Heat-Flux Durability Modeling and Stochastic Progressive Damage Simulation

NASA Technical Reports Server (NTRS)

Zhu, Dongming; Nemeth, Noel N.

2017-01-01

Advanced environmental barrier coatings will play an increasingly important role in future gas turbine engines because of their ability to protect emerging light-weight SiC/SiC ceramic matrix composite (CMC) engine components, further raising engine operating temperatures and performance. Because the environmental barrier coating systems are critical to the performance, reliability and durability of these hot-section ceramic engine components, a prime-reliant coating system along with established life design methodology are required for the hot-section ceramic component insertion into engine service. In this paper, we have first summarized some observations of high temperature, high-heat-flux environmental degradation and failure mechanisms of environmental barrier coating systems in laboratory simulated engine environment tests. In particular, the coating surface cracking morphologies and associated subsequent delamination mechanisms under the engine level high-heat-flux, combustion steam, and mechanical creep and fatigue loading conditions will be discussed. The EBC compostion and archtechture improvements based on advanced high heat flux environmental testing, and the modeling advances based on the integrated Finite Element Analysis Micromechanics Analysis Code/Ceramics Analysis and Reliability Evaluation of Structures (FEAMAC/CARES) program will also be highlighted. The stochastic progressive damage simulation successfully predicts mud flat damage pattern in EBCs on coated 3-D specimens, and a 2-D model of through-the-thickness cross-section. A 2-parameter Weibull distribution was assumed in characterizing the coating layer stochastic strength response and the formation of damage was therefore modeled. The damage initiation and coalescence into progressively smaller mudflat crack cells was demonstrated. A coating life prediction framework may be realized by examining the surface crack initiation and delamination propagation in conjunction with environmental degradation under high-heat-flux and environment load test conditions.

Advanced Ceramic Matrix Composites (CMCs) for High Temperature Applications

NASA Technical Reports Server (NTRS)

Singh, M.

2005-01-01

Advanced ceramic matrix composites (CMCs) are enabling materials for a number of demanding applications in aerospace, energy, and nuclear industries. In the aerospace systems, these materials are being considered for applications in hot sections of jet engines such as the combustor liner, vanes, nozzle components, nose cones, leading edges of reentry vehicles, and space propulsion components. Applications in the energy and environmental industries include radiant heater tubes, heat exchangers, heat recuperators, gas and diesel particulate filters, and components for land based turbines for power generation. These materials are also being considered for use in the first wall and blanket components of fusion reactors. In the last few years, a number of CMC components have been developed and successfully tested for various aerospace and ground based applications. However, a number of challenges still remain slowing the wide scale implementation of these materials. They include robust fabrication and manufacturing, assembly and integration, coatings, property modeling and life prediction, design codes and databases, repair and refurbishment, and cost. Fabrication of net and complex shape components with high density and tailorable matrix properties is quite expensive, and even then various desirable properties are not achievable. In this presentation, a number of examples of successful CMC component development and testing will be provided. In addition, critical need for robust manufacturing, joining and assembly technologies in successful implementation of these systems will be discussed.

Aircraft gas turbine materials and processes.

PubMed

Kear, B H; Thompson, E R

1980-05-23

Materials and processing innovations that have been incorporated into the manufacture of critical components for high-performance aircraft gas turbine engines are described. The materials of interest are the nickel- and cobalt-base superalloys for turbine and burner sections of the engine, and titanium alloys and composites for compressor and fan sections of the engine. Advanced processing methods considered include directional solidification, hot isostatic pressing, superplastic foring, directional recrystallization, and diffusion brazing. Future trends in gas turbine technology are discussed in terms of materials availability, substitution, and further advances in air-cooled hardware.

An integrated risk assessment of the environmental hazards influence on Kazakhstan section (from Khorgas and Dostyk dry ports to Aktau seaport) of the international transport corridor

NASA Astrophysics Data System (ADS)

Akiyanova, F. Zh; Arykbayeva, Z. K.; Atalikhova, A. M.; Dauilbayev, B. A.; Zinabdin, N. B.; Kubeyev, A. B.; Tkach, K. A.

2018-01-01

The article outlines research results on the assessment of natural hazards impact risk on the international transport corridors’ Kazakhstan section (from Khorgas and Dostyk dry ports to the seaport of Aktau) functioning. Based on the component-by-stage analysis of physical and geographical conditions with the use of qualimetric approach, the areas with different risk levels of natural disasters were identified. To minimize the risk of natural problems exposure, a set of environmental recommendations has been developed.

Cramer-Rao Lower Bound Evaluation for Linear Frequency Modulation Based Active Radar Networks Operating in a Rice Fading Environment.

PubMed

Shi, Chenguang; Salous, Sana; Wang, Fei; Zhou, Jianjiang

2016-12-06

This paper investigates the joint target parameter (delay and Doppler) estimation performance of linear frequency modulation (LFM)-based radar networks in a Rice fading environment. The active radar networks are composed of multiple radar transmitters and multichannel receivers placed on moving platforms. First, the log-likelihood function of the received signal for a Rician target is derived, where the received signal scattered off the target comprises of dominant scatterer (DS) component and weak isotropic scatterers (WIS) components. Then, the analytically closed-form expressions of the Cramer-Rao lower bounds (CRLBs) on the Cartesian coordinates of target position and velocity are calculated, which can be adopted as a performance metric to access the target parameter estimation accuracy for LFM-based radar network systems in a Rice fading environment. It is found that the cumulative Fisher information matrix (FIM) is a linear combination of both DS component and WIS components, and it also demonstrates that the joint CRLB is a function of signal-to-noise ratio (SNR), target's radar cross section (RCS) and transmitted waveform parameters, as well as the relative geometry between the target and the radar network architectures. Finally, numerical results are provided to indicate that the joint target parameter estimation performance of active radar networks can be significantly improved with the exploitation of DS component.

Cramer-Rao Lower Bound Evaluation for Linear Frequency Modulation Based Active Radar Networks Operating in a Rice Fading Environment

PubMed Central

Shi, Chenguang; Salous, Sana; Wang, Fei; Zhou, Jianjiang

2016-01-01

This paper investigates the joint target parameter (delay and Doppler) estimation performance of linear frequency modulation (LFM)-based radar networks in a Rice fading environment. The active radar networks are composed of multiple radar transmitters and multichannel receivers placed on moving platforms. First, the log-likelihood function of the received signal for a Rician target is derived, where the received signal scattered off the target comprises of dominant scatterer (DS) component and weak isotropic scatterers (WIS) components. Then, the analytically closed-form expressions of the Cramer-Rao lower bounds (CRLBs) on the Cartesian coordinates of target position and velocity are calculated, which can be adopted as a performance metric to access the target parameter estimation accuracy for LFM-based radar network systems in a Rice fading environment. It is found that the cumulative Fisher information matrix (FIM) is a linear combination of both DS component and WIS components, and it also demonstrates that the joint CRLB is a function of signal-to-noise ratio (SNR), target’s radar cross section (RCS) and transmitted waveform parameters, as well as the relative geometry between the target and the radar network architectures. Finally, numerical results are provided to indicate that the joint target parameter estimation performance of active radar networks can be significantly improved with the exploitation of DS component. PMID:27929433

75 FR 32638 - Defense Federal Acquisition Regulation Supplement; Contract Authority for Advanced Component...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-08

... Prototype Units (DFARS Case 2009-D034) AGENCY: Defense Acquisition Regulations System, Department of Defense... Component Development or Prototype Units.'' Section 819 is intended to prevent a contract for new technology... development of advanced components or the procurement of prototype units. To do so, section 819 places...

GMSEC Interface Specification Document 2016 March

NASA Technical Reports Server (NTRS)

Handy, Matthew

2016-01-01

The GMSEC Interface Specification Document contains the standard set of defined messages. Each GMSEC standard message contains a GMSEC Information Bus Header section and a Message Contents section. Each message section identifies required fields, optional fields, data type and recommended use of the fields. Additionally, this document includes the message subjects associated with the standard messages. The system design of the operations center should ensure the components that are selected use both the API and the defined standard messages in order to achieve full interoperability from component to component.

3-D inelastic analysis methods for hot section components. Volume 2: Advanced special functions models

NASA Technical Reports Server (NTRS)

Wilson, R. B.; Banerjee, P. K.

1987-01-01

This Annual Status Report presents the results of work performed during the third year of the 3-D Inelastic Analysis Methods for Hot Sections Components program (NASA Contract NAS3-23697). The objective of the program is to produce a series of computer codes that permit more accurate and efficient three-dimensional analyses of selected hot section components, i.e., combustor liners, turbine blades, and turbine vanes. The computer codes embody a progression of mathematical models and are streamlined to take advantage of geometrical features, loading conditions, and forms of material response that distinguish each group of selected components.

Overview of online two-dimensional liquid chromatography based on cell membrane chromatography for screening target components from traditional Chinese medicines.

PubMed

Muhammad, Saqib; Han, Shengli; Xie, Xiaoyu; Wang, Sicen; Aziz, Muhammad Majid

2017-01-01

Cell membrane chromatography is a simple, specific, and time-saving technique for studying drug-receptor interactions, screening of active components from complex mixtures, and quality control of traditional Chinese medicines. However, the short column life, low sensitivity, low column efficiency (so cannot resolve satisfactorily mixture of compounds), low peak capacity, and inefficient in structure identification were bottleneck in its application. Combinations of cell membrane chromatography with multidimensional chromatography such as two-dimensional liquid chromatography and high sensitivity detectors like mass have significantly reduced many of the above-mentioned shortcomings. This paper provides an overview of the current advances in online two-dimensional-based cell membrane chromatography for screening target components from traditional Chinese medicines with particular emphasis on the instrumentation, preparation of cell membrane stationary phase, advantages, and disadvantages compared to alternative approaches. The last section of the review summarizes the applications of the online two-dimensional high-performance liquid chromatography based cell membrane chromatography reported since its emergence to date (2010-June 2016). © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Development of a critical appraisal tool to assess the quality of cross-sectional studies (AXIS)

PubMed Central

Downes, Martin J; Brennan, Marnie L; Williams, Hywel C; Dean, Rachel S

2016-01-01

Objectives The aim of this study was to develop a critical appraisal (CA) tool that addressed study design and reporting quality as well as the risk of bias in cross-sectional studies (CSSs). In addition, the aim was to produce a help document to guide the non-expert user through the tool. Design An initial scoping review of the published literature and key epidemiological texts was undertaken prior to the formation of a Delphi panel to establish key components for a CA tool for CSSs. A consensus of 80% was required from the Delphi panel for any component to be included in the final tool. Results An initial list of 39 components was identified through examination of existing resources. An international Delphi panel of 18 medical and veterinary experts was established. After 3 rounds of the Delphi process, the Appraisal tool for Cross-Sectional Studies (AXIS tool) was developed by consensus and consisted of 20 components. A detailed explanatory document was also developed with the tool, giving expanded explanation of each question and providing simple interpretations and examples of the epidemiological concepts being examined in each question to aid non-expert users. Conclusions CA of the literature is a vital step in evidence synthesis and therefore evidence-based decision-making in a number of different disciplines. The AXIS tool is therefore unique and was developed in a way that it can be used across disciplines to aid the inclusion of CSSs in systematic reviews, guidelines and clinical decision-making. PMID:27932337

Ribonucleoprotein components in liver cell nuclei as visualized by cryoultramicrotomy

PubMed Central

1975-01-01

The interphase nucleus of the normal rat hepatocyte has been studied in ultrathin frozen sections after glutaraldehyde fixation and the modification of various staining procedures known to be specific for DNA structures (Moyne's thallium stain, Gautier's osmium-ammine) or preferential for RNP carriers and basic proteins (regressive stains based on the use of EDTA or citrate, negatively charged colloidal iron). The results are comparable to those obtained after classical dehydration and embedding. Particular attention has been paid to the nucleolus and extranucleolar RNP components, such as perichromatin fibrils and granules, as well as interchromatin granules. A striking observation was the uneven size and the strongly increased number of perichromatin granules, and the appearance of a contiguous interchromatin net, containing nucleoproteins. Cryoultramicrotomy without embedding appears to be very useful for the exploration of the nucleus in thick sections which remain sufficiently transparent even with the usual accelerating voltages. PMID:51852

3-D inelastic analysis methods for hot section components (base program). [turbine blades, turbine vanes, and combustor liners

NASA Technical Reports Server (NTRS)

Wilson, R. B.; Bak, M. J.; Nakazawa, S.; Banerjee, P. K.

1984-01-01

A 3-D inelastic analysis methods program consists of a series of computer codes embodying a progression of mathematical models (mechanics of materials, special finite element, boundary element) for streamlined analysis of combustor liners, turbine blades, and turbine vanes. These models address the effects of high temperatures and thermal/mechanical loadings on the local (stress/strain) and global (dynamics, buckling) structural behavior of the three selected components. These models are used to solve 3-D inelastic problems using linear approximations in the sense that stresses/strains and temperatures in generic modeling regions are linear functions of the spatial coordinates, and solution increments for load, temperature and/or time are extrapolated linearly from previous information. Three linear formulation computer codes, referred to as MOMM (Mechanics of Materials Model), MHOST (MARC-Hot Section Technology), and BEST (Boundary Element Stress Technology), were developed and are described.

Processing of Advanced Cast Alloys for A-USC Steam Turbine Applications

NASA Astrophysics Data System (ADS)

Jablonski, Paul D.; Hawk, Jeffery A.; Cowen, Christopher J.; Maziasz, Philip J.

2012-02-01

The high-temperature components within conventional supercritical coal-fired power plants are manufactured from ferritic/martensitic steels. To reduce greenhouse-gas emissions, the efficiency of pulverized coal steam power plants must be increased to as high a temperature and pressure as feasible. The proposed steam temperature in the DOE/NETL Advanced Ultra Supercritical power plant is high enough (760°C) that ferritic/martensitic steels will not work for the majority of high-temperature components in the turbine or for pipes and tubes in the boiler due to temperature limitations of this class of materials. Thus, Ni-based superalloys are being considered for many of these components. Off-the-shelf forged nickel alloys have shown good promise at these temperatures, but further improvements can be made through experimentation within the nominal chemistry range as well as through thermomechanical processing and subsequent heat treatment. However, cast nickel-based superalloys, which possess high strength, creep resistance, and weldability, are typically not available, particularly those with good ductility and toughness that are weldable in thick sections. To address those issues related to thick casting for turbine casings, for example, cast analogs of selected wrought nickel-based superalloys such as alloy 263, Haynes 282, and Nimonic 105 have been produced. Alloy design criteria, melt processing experiences, and heat treatment are discussed with respect to the as-processed and heat-treated microstructures and selected mechanical properties. The discussion concludes with the prospects for full-scale development of a thick section casting for a steam turbine valve chest or rotor casing.

Developing and Implementing a Data Base and Microcomputer Tracking System To Track and Serve Minority Students To Enhance Minority Recruitment and Retention.

ERIC Educational Resources Information Center

Mendoza, Jose

Brief descriptions are provided of several components of Glendale Community College's (GCC's) programs to ensure adequate links with the minority community and stimulate enrollments to achieve parity in enrollment proportions. Introductory sections offer a rationale for minority emphasis programs, define "minority," enumerate reasons for attending…

Effects of an Interteaching Probe on Learning and Generalization of American Psychological Association (APA) Style

ERIC Educational Resources Information Center

Slezak, Jonathan M.; Faas, Caitlin

2017-01-01

This study implemented the components of interteaching as a probe to teach American Psychological Association (APA) Style to undergraduate university students in a psychology research methods and statistics course. The interteaching method was compared to the traditional lecture-based approach between two sections of the course with the same…

75 FR 59745 - In the Matter of: Certain Components for Installation of Marine Autopilots With GPS or IMU...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-09-28

.... Strandvelen 18, Lysaker, Norway. Navico UK, Ltd., Premier Way, Abbey Park, Romsey Hampshire, United Kingdom..., Southampton Road. Portsmouth Hampshire, PO6 4QB, United Kingdom. Raymarine Inc., 21 Manchester Street... violations of section 337 based upon the importation into the United States, the sale for importation, and...

Family differences in equations for predicting biomass and leaf area in Douglas-fir (Pseudotsuga menziesii var. menziesii).

Treesearch

J.B. St. Clair

1993-01-01

Logarithmic regression equations were developed to predict component biomass and leaf area for an 18-yr-old genetic test of Douglas-fir (Pseudotsuga menziesii [Mirb.] Franco var. menziesii) based on stem diameter or cross-sectional sapwood area. Equations did not differ among open-pollinated families in slope, but intercepts...

Impacts of Performance Pay under the Teacher Incentive Fund: Study Design Report

ERIC Educational Resources Information Center

Glazerman, Steven; Chiang, Hanley; Wellington, Alison; Constantine, Jill; Player, Dan

2011-01-01

The body of research on the design, implementation, and effects of performance-based compensation systems has influenced the design and evaluation of the 2010 Teacher Incentive Fund (TIF) grants. In the sections presented here, the authors describe the key components of 2010 TIF grants and the conceptual framework for the evaluation. The remainder…

45 CFR 2552.27 - What two search components of the National Service Criminal History Check must I satisfy to...

Code of Federal Regulations, 2010 CFR

2010-10-01

... position? 2552.27 Section 2552.27 Public Welfare Regulations Relating to Public Welfare (Continued... satisfy to determine an individual's suitability to serve in a covered position? Unless the Corporation... time of application; and (b) National Sex Offender Public Registry. A name-based search of the...

El curriculo creativo para ninos de cero a tres anos (The Creative Curriculum for Infants and Toddlers).

ERIC Educational Resources Information Center

Dombro, Amy Laura; Colker, Laura J.; Dodge, Diane Trister

Stemming from the core idea that infant and toddler care should be based on building relationships, this curriculum in Spanish-language version provides a foundation for staff development. Section 1, "Why a Curriculum for Infants and Toddlers?" examines key quality indicators, discusses curriculum components, describes how to use the…

Passive heat transfer means for nuclear reactors

DOEpatents

Burelbach, James P.

1984-01-01

An improved passive cooling arrangement is disclosed for maintaining adjacent or related components of a nuclear reactor within specified temperature differences. Specifically, heat pipes are operatively interposed between the components, with the vaporizing section of the heat pipe proximate the hot component operable to cool it and the primary condensing section of the heat pipe proximate the other and cooler component operable to heat it. Each heat pipe further has a secondary condensing section that is located outwardly beyond the reactor confinement and in a secondary heat sink, such as air ambient the containment, that is cooler than the other reactor component. Means such as shrouding normally isolated the secondary condensing section from effective heat transfer with the heat sink, but a sensor responds to overheat conditions of the reactor to open the shrouding, which thereby increases the cooling capacity of the heat pipe. By having many such heat pipes, an emergency passive cooling system is defined that is operative without electrical power.

Association Between Awareness of Hypertension and Health-Related Quality of Life in a Cross-Sectional Population-Based Study in Rural Area of Northwest China.

PubMed

Mi, Baibing; Dang, Shaonong; Li, Qiang; Zhao, Yaling; Yang, Ruihai; Wang, Duolao; Yan, Hong

2015-07-01

Hypertensive patients have more complex health care needs and are more likely to have poorer health-related quality of life than normotensive people. The awareness of hypertension could be related to reduce health-related quality of life. We propose the use of quantile regression to explore more detailed relationships between awareness of hypertension and health-related quality of life. In a cross-sectional, population-based study, 2737 participants (including 1035 hypertensive patients and 1702 normotensive participants) completed the Short-Form Health Survey. A quantile regression model was employed to investigate the association of physical component summary scores and mental component summary scores with awareness of hypertension and to evaluate the associated factors. Patients who were aware of hypertension (N = 554) had lower scores than patients who were unaware of hypertension (N = 481). The median (IQR) of physical component summary scores: 48.20 (13.88) versus 53.27 (10.79), P < 0.01; the mental component summary scores: 50.68 (15.09) versus 51.70 (10.65), P = 0.03. adjusting for covariates, the quantile regression results suggest awareness of hypertension was associated with most physical component summary scores quantiles (P < 0.05 except 10th and 20th quantiles) in which the β-estimates from -2.14 (95% CI: -3.80 to -0.48) to -1.45 (95% CI: -2.42 to -0.47), as the same significant trend with some poorer mental component summary scores quantiles in which the β-estimates from -3.47 (95% CI: -6.65 to -0.39) to -2.18 (95% CI: -4.30 to -0.06). The awareness of hypertension has a greater effect on those with intermediate physical component summary status: the β-estimates were equal to -2.04 (95% CI: -3.51 to -0.57, P < 0.05) at the 40th and decreased further to -1.45 (95% CI: -2.42 to -0.47, P < 0.01) at the 90th quantile. Awareness of hypertension was negatively related to health-related quality of life in hypertensive patients in rural western China, which has a greater effect on mental component summary scores with the poorer status and on physical component summary scores with the intermediate status.

Study of component technologies for fuel cell on-site integrated energy system. Volume 2: Appendices

NASA Technical Reports Server (NTRS)

Lee, W. D.; Mathias, S.

1980-01-01

This data base catalogue was compiled in order to facilitate the analysis of various on site integrated energy system with fuel cell power plants. The catalogue is divided into two sections. The first characterizes individual components in terms of their performance profiles as a function of design parameters. The second characterizes total heating and cooling systems in terms of energy output as a function of input and control variables. The integrated fuel cell systems diagrams and the computer analysis of systems are included as well as the cash flows series for baseline systems.

Genetic improvement in mastitis resistance: comparison of selection criteria from cross-sectional and random regression sire models for somatic cell score.

PubMed

Odegård, J; Klemetsdal, G; Heringstad, B

2005-04-01

Several selection criteria for reducing incidence of mastitis were developed from a random regression sire model for test-day somatic cell score (SCS). For comparison, sire transmitting abilities were also predicted based on a cross-sectional model for lactation mean SCS. Only first-crop daughters were used in genetic evaluation of SCS, and the different selection criteria were compared based on their correlation with incidence of clinical mastitis in second-crop daughters (measured as mean daughter deviations). Selection criteria were predicted based on both complete and reduced first-crop daughter groups (261 or 65 daughters per sire, respectively). For complete daughter groups, predicted transmitting abilities at around 30 d in milk showed the best predictive ability for incidence of clinical mastitis, closely followed by average predicted transmitting abilities over the entire lactation. Both of these criteria were derived from the random regression model. These selection criteria improved accuracy of selection by approximately 2% relative to a cross-sectional model. However, for reduced daughter groups, the cross-sectional model yielded increased predictive ability compared with the selection criteria based on the random regression model. This result may be explained by the cross-sectional model being more robust, i.e., less sensitive to precision of (co)variance components estimates and effects of data structure.

Improving Night Time Driving Safety Using Vision-Based Classification Techniques.

PubMed

Chien, Jong-Chih; Chen, Yong-Sheng; Lee, Jiann-Der

2017-09-24

The risks involved in nighttime driving include drowsy drivers and dangerous vehicles. Prominent among the more dangerous vehicles around at night are the larger vehicles which are usually moving faster at night on a highway. In addition, the risk level of driving around larger vehicles rises significantly when the driver's attention becomes distracted, even for a short period of time. For the purpose of alerting the driver and elevating his or her safety, in this paper we propose two components for any modern vision-based Advanced Drivers Assistance System (ADAS). These two components work separately for the single purpose of alerting the driver in dangerous situations. The purpose of the first component is to ascertain that the driver would be in a sufficiently wakeful state to receive and process warnings; this is the driver drowsiness detection component. The driver drowsiness detection component uses infrared images of the driver to analyze his eyes' movements using a MSR plus a simple heuristic. This component issues alerts to the driver when the driver's eyes show distraction and are closed for a longer than usual duration. Experimental results show that this component can detect closed eyes with an accuracy of 94.26% on average, which is comparable to previous results using more sophisticated methods. The purpose of the second component is to alert the driver when the driver's vehicle is moving around larger vehicles at dusk or night time. The large vehicle detection component accepts images from a regular video driving recorder as input. A bi-level system of classifiers, which included a novel MSR-enhanced KAZE-base Bag-of-Features classifier, is proposed to avoid false negatives. In both components, we propose an improved version of the Multi-Scale Retinex (MSR) algorithm to augment the contrast of the input. Several experiments were performed to test the effects of the MSR and each classifier, and the results are presented in experimental results section of this paper.

Improving Night Time Driving Safety Using Vision-Based Classification Techniques

PubMed Central

Chien, Jong-Chih; Chen, Yong-Sheng; Lee, Jiann-Der

2017-01-01

The risks involved in nighttime driving include drowsy drivers and dangerous vehicles. Prominent among the more dangerous vehicles around at night are the larger vehicles which are usually moving faster at night on a highway. In addition, the risk level of driving around larger vehicles rises significantly when the driver’s attention becomes distracted, even for a short period of time. For the purpose of alerting the driver and elevating his or her safety, in this paper we propose two components for any modern vision-based Advanced Drivers Assistance System (ADAS). These two components work separately for the single purpose of alerting the driver in dangerous situations. The purpose of the first component is to ascertain that the driver would be in a sufficiently wakeful state to receive and process warnings; this is the driver drowsiness detection component. The driver drowsiness detection component uses infrared images of the driver to analyze his eyes’ movements using a MSR plus a simple heuristic. This component issues alerts to the driver when the driver’s eyes show distraction and are closed for a longer than usual duration. Experimental results show that this component can detect closed eyes with an accuracy of 94.26% on average, which is comparable to previous results using more sophisticated methods. The purpose of the second component is to alert the driver when the driver’s vehicle is moving around larger vehicles at dusk or night time. The large vehicle detection component accepts images from a regular video driving recorder as input. A bi-level system of classifiers, which included a novel MSR-enhanced KAZE-base Bag-of-Features classifier, is proposed to avoid false negatives. In both components, we propose an improved version of the Multi-Scale Retinex (MSR) algorithm to augment the contrast of the input. Several experiments were performed to test the effects of the MSR and each classifier, and the results are presented in experimental results section of this paper. PMID:28946643

Independent component model for cognitive functions of multiple subjects using [15O]H2O PET images.

PubMed

Park, Hae-Jeong; Kim, Jae-Jin; Youn, Tak; Lee, Dong Soo; Lee, Myung Chul; Kwon, Jun Soo

2003-04-01

An independent component model of multiple subjects' positron emission tomography (PET) images is proposed to explore the overall functional components involved in a task and to explain subject specific variations of metabolic activities under altered experimental conditions utilizing the Independent component analysis (ICA) concept. As PET images represent time-compressed activities of several cognitive components, we derived a mathematical model to decompose functional components from cross-sectional images based on two fundamental hypotheses: (1) all subjects share basic functional components that are common to subjects and spatially independent of each other in relation to the given experimental task, and (2) all subjects share common functional components throughout tasks which are also spatially independent. The variations of hemodynamic activities according to subjects or tasks can be explained by the variations in the usage weight of the functional components. We investigated the plausibility of the model using serial cognitive experiments of simple object perception, object recognition, two-back working memory, and divided attention of a syntactic process. We found that the independent component model satisfactorily explained the functional components involved in the task and discuss here the application of ICA in multiple subjects' PET images to explore the functional association of brain activations. Copyright 2003 Wiley-Liss, Inc.

Multistep Cylindrical Structure Analysis at Normal Incidence Based on Water-Substrate Broadband Metamaterial Absorbers

NASA Astrophysics Data System (ADS)

Fang, Chonghua

2018-01-01

A new multistep cylindrical structure based on water-substrate broadband metamaterial absorbers is designed to reduce the traditional radar cross-section (RCS) of a rod-shaped object. The proposed configuration consists of two distinct parts. One of these components is formed by a four-step cylindrical metal structure, whereas the other one is formed by a new water-substrate broadband metamaterial absorber. The designed structure can significantly reduce the radar cross section more than 10 dB from 4.58 to 18.42 GHz which is the 86.5 % bandwidth of from C-band to 20 GHz. The results of measurement show reasonably good accordance with the simulated ones, which verifies the ability and effect of the proposed design.

Toolbox for the design of LiNbO3-based passive and active integrated quantum circuits

NASA Astrophysics Data System (ADS)

Sharapova, P. R.; Luo, K. H.; Herrmann, H.; Reichelt, M.; Meier, T.; Silberhorn, C.

2017-12-01

We present and discuss perspectives of current developments on advanced quantum optical circuits monolithically integrated in the lithium niobate platform. A set of basic components comprising photon pair sources based on parametric down conversion (PDC), passive routing elements and active electro-optically controllable switches and polarisation converters are building blocks of a toolbox which is the basis for a broad range of diverse quantum circuits. We review the state-of-the-art of these components and provide models that properly describe their performance in quantum circuits. As an example for applications of these models we discuss design issues for a circuit providing on-chip two-photon interference. The circuit comprises a PDC section for photon pair generation followed by an actively controllable modified mach-Zehnder structure for observing Hong-Ou-Mandel interference. The performance of such a chip is simulated theoretically by taking even imperfections of the properties of the individual components into account.

Validation and application of Acoustic Mapping Velocimetry

NASA Astrophysics Data System (ADS)

Baranya, Sandor; Muste, Marian

2016-04-01

The goal of this paper is to introduce a novel methodology to estimate bedload transport in rivers based on an improved bedform tracking procedure. The measurement technique combines components and processing protocols from two contemporary nonintrusive instruments: acoustic and image-based. The bedform mapping is conducted with acoustic surveys while the estimation of the velocity of the bedforms is obtained with processing techniques pertaining to image-based velocimetry. The technique is therefore called Acoustic Mapping Velocimetry (AMV). The implementation of this technique produces a whole-field velocity map associated with the multi-directional bedform movement. Based on the calculated two-dimensional bedform migration velocity field, the bedload transport estimation is done using the Exner equation. A proof-of-concept experiment was performed to validate the AMV based bedload estimation in a laboratory flume at IIHR-Hydroscience & Engineering (IIHR). The bedform migration was analysed at three different flow discharges. Repeated bed geometry mapping, using a multiple transducer array (MTA), provided acoustic maps, which were post-processed with a particle image velocimetry (PIV) method. Bedload transport rates were calculated along longitudinal sections using the streamwise components of the bedform velocity vectors and the measured bedform heights. The bulk transport rates were compared with the results from concurrent direct physical samplings and acceptable agreement was found. As a first field implementation of the AMV an attempt was made to estimate bedload transport for a section of the Ohio river in the United States, where bed geometry maps, resulted by repeated multibeam echo sounder (MBES) surveys, served as input data. Cross-sectional distributions of bedload transport rates from the AMV based method were compared with the ones obtained from another non-intrusive technique (due to the lack of direct samplings), ISSDOTv2, developed by the US Army Corps of Engineers. The good agreement between the results from the two different methods is encouraging and suggests further field tests in varying hydro-morphological situations.

Method and system for providing cooling for turbine components

DOE Office of Scientific and Technical Information (OSTI.GOV)

Morgan, Victor John; Lacy, Benjamin Paul

2016-08-16

A system for providing cooling for a turbine component that includes an outer surface exposed to combustion gases is provided. A component base includes at least one fluid supply passage coupleable to a source of cooling fluid. At least one feed passage communicates with the at least one fluid supply passage. At least one delivery channel communicates with the at least one feed passage. At least one cover layer covers the at least one feed passage and the at least one delivery channel, defining at least in part the component outer surface. At least one discharge passage extends to themore » outer surface. A diffuser section is defined in at least one of the at least one delivery channel and the at least one discharge passage, such that a fluid channeled through the system is diffused prior to discharge adjacent the outer surface.« less

47 CFR 25.254 - Special requirements for ancillary terrestrial components operating in the 1610-1626.5 MHz/2483.5...

Code of Federal Regulations, 2010 CFR

2010-10-01

... components operating in the 1610-1626.5 MHz/2483.5-2500 MHz bands. 25.254 Section 25.254 Telecommunication... Standards § 25.254 Special requirements for ancillary terrestrial components operating in the 1610-1626.5... unacceptable interference to systems identified in paragraph (c) of this section and, in any case, shall not...

SAS program for quantitative stratigraphic correlation by principal components

USGS Publications Warehouse

Hohn, M.E.

1985-01-01

A SAS program is presented which constructs a composite section of stratigraphic events through principal components analysis. The variables in the analysis are stratigraphic sections and the observational units are range limits of taxa. The program standardizes data in each section, extracts eigenvectors, estimates missing range limits, and computes the composite section from scores of events on the first principal component. Provided is an option of several types of diagnostic plots; these help one to determine conservative range limits or unrealistic estimates of missing values. Inspection of the graphs and eigenvalues allow one to evaluate goodness of fit between the composite and measured data. The program is extended easily to the creation of a rank-order composite. ?? 1985.

Mise en oeuvre et etalonnage d'une soufflerie de recherche sur les couches limites

NASA Astrophysics Data System (ADS)

Pioton, Julien

In order to reproduce a turbulent boundary layer separation bubble in a laboratory at the École de Technologie Supérieure of Montreal, an open-circuit wind tunnel equipped with a blow-down centrifugal fan has been implemented and calibrated for this research project. The methodology for the conception of the wind tunnel components, based on the results obtained from previous experiments, has been validated by the comparison between experimental and theoretical pressure losses along the wind tunnel. Dimensionless mean axial velocity measurements in the working section have showed an irrotational uniform flow zone at the contraction end, which demonstrates the satisfactory performance of the flowconditioning components located upstream from the working section. Mean axial velocity and total pressure measurements along the working section have allowed for estimates of the location of boundary between irrotational and rotational flow at the separation bubble. The maximum mean height of the boundary layer has been estimated at around 15 cm. Oil film visualisations have revealed a mean bubble separation length of approximately 52 cm. Theses oil visualisations, supported by mean lateral velocity measurements in the current configuration of the working section, have indicated important three-dimensional effects and significant dissymmetry in the vicinity of the separation and reattachment zones at the separation bubble.

The role of nonlinear torsional contributions on the stability of flexural-torsional oscillations of open-cross section beams

NASA Astrophysics Data System (ADS)

Di Egidio, Angelo; Contento, Alessandro; Vestroni, Fabrizio

2015-12-01

An open-cross section thin-walled beam model, already developed by the authors, has been conveniently simplified while maintaining the capacity of accounting for the significant nonlinear warping effects. For a technical range of geometrical and mechanical characteristics of the beam, the response is characterized by the torsional curvature prevailing over the flexural ones. A Galerkin discretization is performed by using a suitable expansion of displacements based on shape functions. The attention is focused on the dynamic response of the beam to a harmonic force, applied at the free end of the cantilever beam. The excitation is directed along the symmetry axis of the beam section. The stability of the one-component oscillations has been investigated using the analytical model, showing the importance of the internal resonances due to the nonlinear warping coupling terms. Comparison with the results provided by a computational finite element model has been performed. The good agreement among the results of the analytical and the computational models confirms the effectiveness of the simplified model of a nonlinear open-cross section thin-walled beam and overall the important role of the warping and of the torsional elongation in the study of the one-component dynamic oscillations and their stability.

Performance Characterization of Digital Optical Data Transfer Systems for Use in the Space Radiation Environment

NASA Technical Reports Server (NTRS)

Reed, Robert A.; Ladbury, Ray L.; Day, John H. (Technical Monitor)

2000-01-01

Radiation effects in photonic and microelectronic components can impact the performance of high-speed digital optical data link in a variety of ways. This segment of the short course focuses on radiation effects in digital optical data links operating in the MHz to GHz regime. (Some of the information is applicable to frequencies above and below this regime) The three basic component level effects that should be considered are Total Ionizing Dose (TID), Displacement Damage Dose (DDD) and Single Event Effects (SEE). In some cases the system performance degradation can be quantified from component level tests, while in others a more holistic characterization approach must be taken. In Section 2.0 of this segment of the Short Course we will give a brief overview of the space radiation environment follow by a summary of the basic space radiation effects important for microelectronics and photonics listed above. The last part of this section will give an example of a typical mission radiation environment requirements. Section 3.0 gives an overview of intra-satellite digital optical data link systems. It contains a discussion of the digital optical data link and it's components. Also, we discuss some of the important system performance metrics that are impacted by radiation effects degradation of optical and optoelectronic component performance. Section 4.0 discusses radiation effects in optical and optoelectronic components. While each component effect will be discussed, the focus of this section is on degradation of passive optical components and SEE in photodiodes (other mechanisms are covered in segment II of this short course entitled "Photonic Devices with Complex and Multiple Failure Modes"). Section 5.0 will focus on optical data link system response to the space radiation environment. System level SEE ground testing will be discussed. Then we give a discussion of system level assessment of data link performance when operating in the space radiation environment.

Potential advantages associated with implementing a risk-based inspection program by a nuclear facility

NASA Astrophysics Data System (ADS)

McNeill, Alexander, III; Balkey, Kenneth R.

1995-05-01

The current inservice inspection activities at a U.S. nuclear facility are based upon the American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code, Section XI. The Code selects examination locations based upon a sampling criteria which includes component geometry, stress, and usage among other criteria. This can result in a significant number of required examinations. As a result of regulatory action each nuclear facility has conducted probabilistic risk assessments (PRA) or individual plant examinations (IPE), producing plant specific risk-based information. Several initiatives have been introduced to apply this new plant risk information. Among these initiatives is risk-based inservice inspection. A code case has been introduced for piping inspections based upon this new risk- based technology. This effort brought forward to the ASME Section XI Code committee, has been initiated and championed by the ASME Research Task Force on Risk-Based Inspection Guidelines -- LWR Nuclear Power Plant Application. Preliminary assessments associated with the code case have revealed that potential advantages exist in a risk-based inservice inspection program with regard to a number of exams, risk, personnel exposure, and cost.

Process Evaluation of a School-Based Education Program about Organ Donation and Registration, and the Intention for Continuance

ERIC Educational Resources Information Center

Reubsaet, A.; Reinaerts, E. B. M.; Brug, J.; van Hooff, J. P.; van den Borne, H. W.

2004-01-01

This paper describes the process evaluation of an organ donation education program for high school students aged 15-18 years of which the effectiveness was established. The program consisted of three components: a video with group discussion, an interactive computer-tailored program and a registration training session. A cross-sectional survey was…

Automatic Processing of Metallurgical Abstracts for the Purpose of Information Retrieval. Final Report.

ERIC Educational Resources Information Center

Melton, Jessica S.

Objectives of this project were to develop and test a method for automatically processing the text of abstracts for a document retrieval system. The test corpus consisted of 768 abstracts from the metallurgical section of Chemical Abstracts (CA). The system, based on a subject indexing rational, had two components: (1) a stored dictionary of words…

Environmental Barrier Coatings for Ceramic Matrix Composites - An Overview

NASA Technical Reports Server (NTRS)

Lee, Kang; Zhu, Dongming; Wiesner, Valerie Lynn; van Roode, Mark; Kashyap, Tania; Zhu, Dongming; Wiesner, Valerie

2016-01-01

Ceramic Matrix Composites (CMCs) are increasingly being considered as structural materials for advanced power generation equipment. Broadly speaking the two classes of materials are oxide-based CMCs and non-oxide based CMCs. The non-oxide CMCs are primarily silicon-based. Under conditions prevalent in the gas turbine hot section the water vapor formed in the combustion of gaseous or liquid hydrocarbons reacts with the surface-SiO2 to form volatile products. Progressive surface recession of the SiC-SiC CMC component, strength loss as a result of wall thinning and chemical changes in the component occur, which leads to the loss of structural integrity and mechanical strength and becomes life limiting to the equipment in service. The solutions pursued to improve the life of SiC-SiC CMCs include the incorporation of an external barrier coating to provide surface protection to the CMC substrate. The coating system has become known as an Environmental Barrier Coating (EBC). The relevant early coatings work was focused on coatings for corrosion protection of silicon-based monolithic ceramics operating under severely corrosive conditions. The development of EBCs for gas turbine hot section components was built on the early work for silicon-based monolithics. The first generation EBC is a three-layer coating, which in its simplest configuration consists of a silicon (Si) base coat applied on top of the CMC, a barium-strontium-aluminosilicate (BSAS) surface coat resistant to water vapor attack, and a mullite-based intermediate coating layer between the Si base coat and BSAS top coat. This system can be represented as Si-Mullite-BSAS. While this baseline EBC presented a significant improvement over the uncoated SiC-SiC CMC, for the very long durations of 3-4 years or more expected for industrial operation further improvements in coating durability are desirable. Also, for very demanding applications with higher component temperatures but shorter service lives more rugged EBCs will be necessary. A second generation of EBCs incorporates rare earth silicates which have extremely favorable resistance against environmental attack and a higher temperature capability. Performance data for this class of EBCs is more limited and especially field data are not as extensive as for the first generation EBCs. Extensive laboratory, rig and engine testing, including testing of EBC coated SiC-SiC CMCs in actual field applications is in progress. The development of next generation EBCs with even higher temperature capability than the second generation EBC is also underway. This paper will discuss the current status of EBC technology and future direction based on literature survey.

Prevalence and Correlates of Insufficient Sleep Syndrome in Japanese Young Adults: A Web-Based Cross-Sectional Study.

PubMed

Morita, Yuko; Sasai-Sakuma, Taeko; Asaoka, Shoichi; Inoue, Yuichi

2015-10-15

This study investigated the prevalence and risk factors of insufficient sleep syndrome (ISS), and factors associated with daytime dysfunction in the disorder in Japanese young adults. In this cross-sectional study, a web-based questionnaire survey was used to assess demographic variables, sleep habits and quality, depressive symptoms, and health-related quality of life (HRQOL) in 2,276 participants aged 20-25. Eleven percent of participants were classified as having ISS. Multiple logistic regression analysis revealed that the presence of ISS was significantly associated with social status (student or full-time employee). The participants with ISS had significantly higher depression scores and lower mental component summary scores than healthy sleepers. In the participants with ISS, a delayed sleep-wake schedule was extracted as a factor associated with worse mental component summary. Results indicate a relatively high proportion of Japanese young adults suffer from ISS, and that the condition is associated with a social status of student or full-time employee. Moreover, a delayed sleep-wake schedule may lead to further deterioration of mental HRQOL in ISS-affected persons. © 2015 American Academy of Sleep Medicine.

Power Enhancement in High Dimensional Cross-Sectional Tests

PubMed Central

Fan, Jianqing; Liao, Yuan; Yao, Jiawei

2016-01-01

We propose a novel technique to boost the power of testing a high-dimensional vector H : θ = 0 against sparse alternatives where the null hypothesis is violated only by a couple of components. Existing tests based on quadratic forms such as the Wald statistic often suffer from low powers due to the accumulation of errors in estimating high-dimensional parameters. More powerful tests for sparse alternatives such as thresholding and extreme-value tests, on the other hand, require either stringent conditions or bootstrap to derive the null distribution and often suffer from size distortions due to the slow convergence. Based on a screening technique, we introduce a “power enhancement component”, which is zero under the null hypothesis with high probability, but diverges quickly under sparse alternatives. The proposed test statistic combines the power enhancement component with an asymptotically pivotal statistic, and strengthens the power under sparse alternatives. The null distribution does not require stringent regularity conditions, and is completely determined by that of the pivotal statistic. As specific applications, the proposed methods are applied to testing the factor pricing models and validating the cross-sectional independence in panel data models. PMID:26778846

A Critical Analysis of the Conventionally Employed Creep Lifing Methods

PubMed Central

Abdallah, Zakaria; Gray, Veronica; Whittaker, Mark; Perkins, Karen

2014-01-01

The deformation of structural alloys presents problems for power plants and aerospace applications due to the demand for elevated temperatures for higher efficiencies and reductions in greenhouse gas emissions. The materials used in such applications experience harsh environments which may lead to deformation and failure of critical components. To avoid such catastrophic failures and also increase efficiency, future designs must utilise novel/improved alloy systems with enhanced temperature capability. In recognising this issue, a detailed understanding of creep is essential for the success of these designs by ensuring components do not experience excessive deformation which may ultimately lead to failure. To achieve this, a variety of parametric methods have been developed to quantify creep and creep fracture in high temperature applications. This study reviews a number of well-known traditionally employed creep lifing methods with some more recent approaches also included. The first section of this paper focuses on predicting the long-term creep rupture properties which is an area of interest for the power generation sector. The second section looks at pre-defined strains and the re-production of full creep curves based on available data which is pertinent to the aerospace industry where components are replaced before failure. PMID:28788623

On 3-D inelastic analysis methods for hot section components. Volume 1: Special finite element models

NASA Technical Reports Server (NTRS)

Nakazawa, S.

1988-01-01

This annual status report presents the results of work performed during the fourth year of the 3-D Inelastic Analysis Methods for Hot Section Components program (NASA Contract NAS3-23697). The objective of the program is to produce a series of new computer codes permitting more accurate and efficient 3-D analysis of selected hot section components, i.e., combustor liners, turbine blades and turbine vanes. The computer codes embody a progression of math models and are streamlined to take advantage of geometrical features, loading conditions, and forms of material response that distinguish each group of selected components. Volume 1 of this report discusses the special finite element models developed during the fourth year of the contract.

Magnetostratigraphy of Early Middle Toarcian expanded sections from the Iberian Range (central Spain)

NASA Astrophysics Data System (ADS)

Osete, María-Luisa; Gialanella, Paola-Romana; Gómez, Juan J.; Villalaín, Juan J.; Goy, Antonio; Heller, Friedrich

2007-07-01

The magnetostratigraphy of the Lower-Middle Toarcian has been established in two well-dated stratigraphically expanded sections: the Sierra Palomera and the Ariño sections, located in the Iberian Range, in central-eastern Spain. Two magnetisation components could be isolated by thermal cleaning: a secondary syntectonic component of always normal polarity unblocking at intermediate temperatures up to 450 °C/475 °C (A component) and a high temperature unblocking component up to 575 °C (B component). The B component passes fold and reversal tests and is considered the characteristic remanent magnetisation of primary origin. The first Toarcian palaeomagnetic pole for Iberia has been obtained: Plat = 77.4°, Plon = 241.3°E (dm = 5.4° dp = 6.0°). Five pairs of normal and reversed polarity zones were calibrated to regional ammonite subzones. The pattern can be calibrated to other Toarcian magnetostratigraphic studies, but provides a more detailed biostratigraphic framework. A refined magnetic polarity time scale is proposed for the Lower-Middle Toarcian.

Almond-Shaped Test Body

NASA Technical Reports Server (NTRS)

Dominek, Allen; Wood, Richard; Gilreath, Mel

1992-01-01

Almond shaped test body developed for use in electromagnetic anechoic chamber for evaluation of range and measurement of components has low radar cross section that varies with angle over large dynamic range. Surface is composite formed by joining properly scaled ellipsoidal surfaces. Used to mount components whose radar cross sections are to be measured, and simulate backscatter characteristics of component as though it were over infinite ground plane.

Electron-neutrino scattering off nuclei from two different theoretical perspectives

NASA Astrophysics Data System (ADS)

Martini, M.; Jachowicz, N.; Ericson, M.; Pandey, V.; Van Cuyck, T.; Van Dessel, N.

2016-07-01

We analyze charged-current electron-neutrino cross sections on carbon. We consider two different theoretical approaches, on one hand the continuum random phase approximation (CRPA) which allows a description of giant resonances and quasielastic excitations, on the other hand the RPA-based calculations which are able to describe multinucleon emission and coherent and incoherent pion production as well as quasielastic excitations. We compare the two approaches in the genuine quasielastic channel, and find a satisfactory agreement between them at large energies while at low energies the collective giant resonances show up only in the CRPA approach. We also compare electron-neutrino cross sections with the corresponding muon-neutrino ones in order to investigate the impact of the different charged-lepton masses. Finally, restricting to the RPA-based approach, we compare the sum of quasielastic, multinucleon emission, coherent, and incoherent one-pion production cross sections (folded with the electron-neutrino T2K flux) with the charged-current inclusive electron-neutrino differential cross sections on carbon measured by T2K. We find a good agreement with the data. The multinucleon component is needed in order to reproduce the T2K electron-neutrino inclusive cross sections.

A seismic fault recognition method based on ant colony optimization

NASA Astrophysics Data System (ADS)

Chen, Lei; Xiao, Chuangbai; Li, Xueliang; Wang, Zhenli; Huo, Shoudong

2018-05-01

Fault recognition is an important section in seismic interpretation and there are many methods for this technology, but no one can recognize fault exactly enough. For this problem, we proposed a new fault recognition method based on ant colony optimization which can locate fault precisely and extract fault from the seismic section. Firstly, seismic horizons are extracted by the connected component labeling algorithm; secondly, the fault location are decided according to the horizontal endpoints of each horizon; thirdly, the whole seismic section is divided into several rectangular blocks and the top and bottom endpoints of each rectangular block are considered as the nest and food respectively for the ant colony optimization algorithm. Besides that, the positive section is taken as an actual three dimensional terrain by using the seismic amplitude as a height. After that, the optimal route from nest to food calculated by the ant colony in each block is judged as a fault. Finally, extensive comparative tests were performed on the real seismic data. Availability and advancement of the proposed method were validated by the experimental results.

Strategies for improving antibiotic use in Qatar: a survey of pharmacists' perceptions and experiences.

PubMed

Pawluk, Shane; Black, Emily; El-Awaisi, Alla

2015-02-01

The objectives of this study were to identify antimicrobial stewardship activities in Qatar, identify pharmacist involvement in activities and summarize perceived barriers for implementation of antimicrobial stewardship programs (ASPs). A cross-sectional survey was developed based on study objectives and completed by pharmacists in Qatar. Most hospital settings have implemented components of ASP. Lack of infectious disease specialists and training of healthcare providers was the most common barrier to implementation or expansion of ASP identified in the hospital and community settings respectively. Pharmacists report some components of ASP have been implemented; however, barriers must be overcome to further expand ASPs. © 2014 Royal Pharmaceutical Society.

Issues in Defining Software Architectures in a GIS Environment

NASA Technical Reports Server (NTRS)

Acosta, Jesus; Alvorado, Lori

1997-01-01

The primary mission of the Pan-American Center for Earth and Environmental Studies (PACES) is to advance the research areas that are relevant to NASA's Mission to Planet Earth program. One of the activities at PACES is the establishment of a repository for geographical, geological and environmental information that covers various regions of Mexico and the southwest region of the U.S. and that is acquired from NASA and other sources through remote sensing, ground studies or paper-based maps. The center will be providing access of this information to other government entities in the U.S. and Mexico, and research groups from universities, national laboratories and industry. Geographical Information Systems(GIS) provide the means to manage, manipulate, analyze and display geographically referenced information that will be managed by PACES. Excellent off-the-shelf software exists for a complete GIS as well as software for storing and managing spatial databases, processing images, networking and viewing maps with layered information. This allows the user flexibility in combining systems to create a GIS or to mix these software packages with custom-built application programs. Software architectural languages provide the ability to specify the computational components and interactions among these components, an important topic in the domain of GIS because of the need to integrate numerous software packages. This paper discusses the characteristics that architectural languages address with respect to the issues relating to the data that must be communicated between software systems and components when systems interact. The paper presents a background on GIS in section 2. Section 3 gives an overview of software architecture and architectural languages. Section 4 suggests issues that may be of concern when defining the software architecture of a GIS. The last section discusses the future research effort and finishes with a summary.

Exclusive ρ0 meson electroproduction from hydrogen at CLAS

NASA Astrophysics Data System (ADS)

Clas Collaboration; Hadjidakis, C.; Guidal, M.; Garçon, M.; Laget, J.-M.; Smith, E. S.; Vanderhaeghen, M.; Adams, G.; Ambrozewicz, P.; Anciant, E.; Anghinolfi, M.; Asavapibhop, B.; Asryan, G.; Audit, G.; Auger, T.; Avakian, H.; Bagdasaryan, H.; Ball, J. P.; Barrow, S.; Battaglieri, M.; Beard, K.; Bektasoglu, M.; Bellis, M.; Benmouna, N.; Bianchi, N.; Biselli, A. S.; Boiarinov, S.; Bonner, B. E.; Bouchigny, S.; Bradford, R.; Branford, D.; Briscoe, W. J.; Brooks, W. K.; Burkert, V. D.; Butuceanu, C.; Calarco, J. R.; Carman, D. S.; Carnahan, B.; Cetina, C.; Chen, S.; Cole, P. L.; Coleman, A.; Cords, D.; Corvisiero, P.; Crabb, D.; Crannell, H.; Cummings, J. P.; de Sanctis, E.; Devita, R.; Degtyarenko, P. V.; Dennis, L.; Dharmawardane, K. V.; Dhuga, K. S.; Didelez, J.-P.; Djalali, C.; Dodge, G. E.; Doughty, D.; Dragovitsch, P.; Dugger, M.; Dytman, S.; Dzyubak, O. P.; Egiyan, H.; Egiyan, K. S.; Elouadrhiri, L.; Empl, A.; Eugenio, P.; Farhi, L.; Fatemi, R.; Feuerbach, R. J.; Forest, T. A.; Frolov, V.; Funsten, H.; Gaff, S. J.; Gavalian, G.; Gilfoyle, G. P.; Giovanetti, K. L.; Girard, P.; Gordon, C. I. O.; Gothe, R. W.; Griffioen, K. A.; Guillo, M.; Guler, M.; Guo, L.; Gyurjyan, V.; Hakobyan, R. S.; Hardie, J.; Heddle, D.; Hersman, F. W.; Hicks, K.; Hleiqawi, H.; Holtrop, M.; Hourany, E.; Hu, J.; Hyde-Wright, C. E.; Ilieva, Y.; Ireland, D.; Ito, M. M.; Jenkins, D.; Jo, H.-S.; Joo, K.; Juengst, H. G.; Kelley, J. H.; Kellie, J.; Khandaker, M.; Kim, K. Y.; Kim, K.; Kim, W.; Klein, A.; Klein, F. J.; Klimenko, A. V.; Klusman, M.; Kossov, M.; Kramer, L. H.; Kuhn, S. E.; Kuhn, J.; Lachniet, J.; Langheinrich, J.; Lawrence, D.; Lee, T.; Li, Ji; Livingstone, K.; Lukashin, K.; Manak, J. J.; Marchand, C.; McAleer, S.; McNabb, J. W. C.; Mecking, B. A.; Melone, J. J.; Mestayer, M. D.; Meyer, C. A.; Mikhailov, K.; Minehart, R.; Mirazita, M.; Miskimen, R.; Morand, L.; Morrow, S. A.; Muccifora, V.; Mueller, J.; Mutchler, G. S.; Napolitano, J.; Nasseripour, R.; Nelson, S. O.; Niccolai, S.; Niculescu, G.; Niculescu, I.; Niczyporuk, B. B.; Niyazov, R. A.; Nozar, M.; O'Rielly, G. V.; Osipenko, M.; Park, K.; Pasyuk, E.; Peterson, G.; Philips, S. A.; Pivnyuk, N.; Pocanic, D.; Pogorelko, O.; Polli, E.; Pozdniakov, S.; Preedom, B. M.; Price, J. W.; Prok, Y.; Protopopescu, D.; Qin, L. M.; Raue, B. A.; Riccardi, G.; Ricco, G.; Ripani, M.; Ritchie, B. G.; Ronchetti, F.; Rossi, P.; Rosner, G.; Rowntree, D.; Rubin, P. D.; Sabatié, F.; Sabourov, K.; Salgado, C.; Santoro, J. P.; Sapunenko, V.; Schumacher, R. A.; Serov, V. S.; Sharabian, Y. G.; Shaw, J.; Simionatto, S.; Skabelin, A. V.; Smith, L. C.; Sober, D. I.; Spraker, M.; Stavinsky, A.; Stepanyan, S.; Stokes, B. E.; Stoler, P.; Strauch, S.; Taiuti, M.; Taylor, S.; Tedeschi, D. J.; Thoma, U.; Thompson, R.; Tkabladze, A.; Todor, L.; Tur, C.; Ungaro, M.; Vineyard, M. F.; Vlassov, A. V.; Wang, K.; Weinstein, L. B.; Weller, H.; Weygand, D. P.; Whisnant, C. S.; Williams, M.; Wolin, E.; Wood, M. H.; Yegneswaran, A.; Yun, J.; Zana, L.

2005-01-01

The longitudinal and transverse components of the cross section for the ep→e‧pρ0 reaction were measured in Hall B at Jefferson Laboratory using the CLAS detector. The data were taken with a 4.247 GeV electron beam and were analyzed in a range of xB from 0.2 to 0.6 and of Q2 from 1.5 to 3.0 GeV2. The data are compared to a Regge model based on effective hadronic degrees of freedom and to a calculation based on Generalized Parton Distributions. It is found that, at our lowest xB values, the transverse part of the cross section is well described by the former approach while the longitudinal part can be reproduced by the latter.

Combining ESPI with laser scanning for 3D characterization of racing tyres sections

NASA Astrophysics Data System (ADS)

Pagliarulo, Vito; Farroni, Flavio; Ferraro, Pietro; Lanzotti, Antonio; Martorelli, Massimo; Memmolo, Pasquale; Speranza, Domenico; Timpone, Francesco

2018-05-01

In this work is exploited the possibility to use two optical techniques and combining their measurements for the 3D characterization of different tyres with particular attention to the tyre's section. Electronic Speckle Pattern Interferometry (ESPI) and Laser Scanner (LS) based on principle of triangulation have been employed for investigating and studying the tyre's section and 3D shape respectively. As case studies two different racing tyres, Michelin S9H and Pirelli Diablo respectively, have been considered. The investigation has been focused at the aim to evaluate and measure the section's components in order to add to the 3D model obtained by Laser Scanning accurate information about the different layers along through the tyres sections. It is important to note that the assessment about the different layers along the section is a very difficult task to obtain by visual inspection or classical microscopy and even with the LS. Here we demonstrate that the different layers can be easily highlighted and identified by mean of the ESPI.

TRENCADIS - secure architecture to share and manage DICOM objects in a ontological framework based on OGSA.

PubMed

Blanquer, Ignacio; Hernandez, Vicente; Segrelles, Damià; Torres, Erik

2007-01-01

Today most European healthcare centers use the digital format for their databases of images. TRENCADIS is a software architecture comprising a set of services as a solution for interconnecting, managing and sharing selected parts of medical DICOM data for the development of training and decision support tools. The organization of the distributed information in virtual repositories is based on semantic criteria. Different groups of researchers could organize themselves to propose a Virtual Organization (VO). These VOs will be interested in specific target areas, and will share information concerning each area. Although the private part of the information to be shared will be removed, special considerations will be taken into account to avoid the access by non-authorized users. This paper describes the security model implemented as part of TRENCADIS. The paper is organized as follows. First introduces the problem and presents our motivations. Section 1 defines the objectives. Section 2 presents an overview of the existing proposals per objective. Section 3 outlines the overall architecture. Section 4 describes how TRENCADIS is architected to realize the security goals discussed in the previous sections. The different security services and components of the infrastructure are briefly explained, as well as the exposed interfaces. Finally, Section 5 concludes and gives some remarks on our future work.

HIGH DIMENSIONAL COVARIANCE MATRIX ESTIMATION IN APPROXIMATE FACTOR MODELS.

PubMed

Fan, Jianqing; Liao, Yuan; Mincheva, Martina

2011-01-01

The variance covariance matrix plays a central role in the inferential theories of high dimensional factor models in finance and economics. Popular regularization methods of directly exploiting sparsity are not directly applicable to many financial problems. Classical methods of estimating the covariance matrices are based on the strict factor models, assuming independent idiosyncratic components. This assumption, however, is restrictive in practical applications. By assuming sparse error covariance matrix, we allow the presence of the cross-sectional correlation even after taking out common factors, and it enables us to combine the merits of both methods. We estimate the sparse covariance using the adaptive thresholding technique as in Cai and Liu (2011), taking into account the fact that direct observations of the idiosyncratic components are unavailable. The impact of high dimensionality on the covariance matrix estimation based on the factor structure is then studied.

Structural damage continuous monitoring by using a data driven approach based on principal component analysis and cross-correlation analysis

NASA Astrophysics Data System (ADS)

Camacho-Navarro, Jhonatan; Ruiz, Magda; Villamizar, Rodolfo; Mujica, Luis; Moreno-Beltrán, Gustavo; Quiroga, Jabid

2017-05-01

Continuous monitoring for damage detection in structural assessment comprises implementation of low cost equipment and efficient algorithms. This work describes the stages involved in the design of a methodology with high feasibility to be used in continuous damage assessment. Specifically, an algorithm based on a data-driven approach by using principal component analysis and pre-processing acquired signals by means of cross-correlation functions, is discussed. A carbon steel pipe section and a laboratory tower were used as test structures in order to demonstrate the feasibility of the methodology to detect abrupt changes in the structural response when damages occur. Two types of damage cases are studied: crack and leak for each structure, respectively. Experimental results show that the methodology is promising in the continuous monitoring of real structures.

Femtosecond Fiber Lasers Based on Dissipative Processes for Nonlinear Microscopy.

PubMed

Wise, Frank W

2012-01-01

Recent progress in the development of femtosecond-pulse fiber lasers with parameters appropriate for nonlinear microscopy is reviewed. Pulse-shaping in lasers with only normal-dispersion components is briefly described, and the performance of the resulting lasers is summarized. Fiber lasers based on the formation of dissipative solitons now offer performance competitive with that of solid-state lasers, but with the benefits of the fiber medium. Lasers based on self-similar pulse evolution in the gain section of a laser also offer a combination of short pulse duration and high pulse energy that will be attractive for applications in nonlinear bioimaging.

Development of an alkaline fuel cell subsystem

NASA Technical Reports Server (NTRS)

1987-01-01

A two task program was initiated to develop advanced fuel cell components which could be assembled into an alkaline power section for the Space Station Prototype (SSP) fuel cell subsystem. The first task was to establish a preliminary SSP power section design to be representative of the 200 cell Space Station power section. The second task was to conduct tooling and fabrication trials and fabrication of selected cell stack components. A lightweight, reliable cell stack design suitable for the SSP regenerative fuel cell power plant was completed. The design meets NASA's preliminary requirements for future multikilowatt Space Station missions. Cell stack component fabrication and tooling trials demonstrated cell components of the SSP stack design of the 1.0 sq ft area can be manufactured using techniques and methods previously evaluated and developed.

Novel Thin Film Sensor Technology for Turbine Engine Hot Section Components

NASA Technical Reports Server (NTRS)

Wrbanek, John D.; Fralick, Gustave C.

2007-01-01

Degradation and damage that develops over time in hot section components can lead to catastrophic failure of the turbine section of aircraft engines. A range of thin film sensor technology has been demonstrated enabling on-component measurement of multiple parameters either individually or in sensor arrays including temperature, strain, heat flux, and flow. Conductive ceramics are beginning to be investigated as new materials for use as thin film sensors in the hot section, leveraging expertise in thin films and high temperature materials. The current challenges are to develop new sensor and insulation materials capable of withstanding the extreme hot section environment, and to develop techniques for applying sensors onto complex high temperature structures for aging studies of hot propulsion materials. The technology research and development ongoing at NASA Glenn Research Center for applications to future aircraft, launch vehicles, space vehicles, and ground systems is outlined.

Structure Formation and Properties of Weld Overlay Produced by Laser Cladding under the Influence of Nanoparticles of High-melting Compounds

NASA Astrophysics Data System (ADS)

Murzakov, M.; Petrovskiy, V.; Birukov, V.; Dzhumaev, P.; Polski, V.; Markushov, Y.; Bykovskiy, D.

Researches of flat samples using laser cladding technology were carried out. Nickel-based powders with the addition of nanopowders of tantalum carbide and tungsten carbide with water-based hydroxyethylcellulose as the binder, were used for slip cladding. Powders are fused on under local argon protection. The experiments were carried out to determine minimal base metal penetration depth, microhardness distribution over cross section of substrate and deposited layers, enrichment level of cladding metal with base components depending on power density and deposition rate. Metallographic studies of obtained overlays were conducted using a high-precision analytical equipment.

How Organizations Can Enhance the Quality of Life of Their Clients and Assess Their Results: The Concept of QOL Enhancement

ERIC Educational Resources Information Center

Reinders, Hans S.; Schalock, Robert L.

2014-01-01

This article presents the framework of a dynamic approach to quality of life (QOL) enhancement based on the conceptualization and measurement of individual-referenced quality of life. Sections of the article summarize the premises of QOL enhancement, provide the rationale for a dynamic approach to QOL enhancement, discuss six components of QOL…

Navy High-Strength Steel Corrosion-Fatigue Modeling Program

DTIC Science & Technology

2006-10-01

interest. In the global analysis, the axial loading and residual stress (via the temperature profile discussed in the previous section) were applied to...developed based on observa- tions from analyses of axial load components with sinusoidally varying surface geometries. These observations indicated that...profile parameters (height and wavelength in each surface direction) and the applied axial loading . Stress Varies Sinusoidally 180° Out of Phase

30 CFR 1206.174 - How do I value gas production when an index-based method cannot be used?

Code of Federal Regulations, 2012 CFR

2012-07-01

... production that cannot be valued under § 1206.172, as well as gas plant products, and to value components of... data than the data described in paragraph (a)(4)(iii) of this section or data to augment the data... the augmented data source beginning with production on the first day of the month following the date...

30 CFR 1206.174 - How do I value gas production when an index-based method cannot be used?

Code of Federal Regulations, 2014 CFR

2014-07-01

... production that cannot be valued under § 1206.172, as well as gas plant products, and to value components of... data than the data described in paragraph (a)(4)(iii) of this section or data to augment the data... the augmented data source beginning with production on the first day of the month following the date...

30 CFR 1206.174 - How do I value gas production when an index-based method cannot be used?

Code of Federal Regulations, 2013 CFR

2013-07-01

... production that cannot be valued under § 1206.172, as well as gas plant products, and to value components of... data than the data described in paragraph (a)(4)(iii) of this section or data to augment the data... the augmented data source beginning with production on the first day of the month following the date...

Report on a Highly Used Computer Aid for the Professor in his Grade and Record Keeping Tasks.

ERIC Educational Resources Information Center

Brockmeier, Richard

SPARS is a computer data base management system designed to aid the college professor in handling his students' grades and other classroom data. It can handle multiple sections and labs, and allows the professor to combine and separate these components in a variety of ways. SPARS seeks to meet the sometimes competing goals of simplicity of use and…

Classroom Practice in Reading.

ERIC Educational Resources Information Center

Earle, Richard A., Ed.

Each of the five sections in this book deals with one of the five major components in a diagnostic/prescriptive model of classroom reading instruction: instructional purpose, evaluation, materials, methods, and classroom management. Articles in the "Instructional Purpose" section discuss the affective component of instruction and the relationship…

Assuring Structural Integrity in Army Systems

DTIC Science & Technology

1985-02-28

power plants are* I. American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code , Section III - Rules for Construction of Nuclear...Power Plant Components; 2. ASNE Boiler and Pressure Vessel Code , Section XI, Rules for In-Service Inspection of Nuclear Power Plant Components; and 3

Cooled electronic system with liquid-cooled cold plate and thermal spreader coupled to electronic component

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chainer, Timothy J.; Graybill, David P.; Iyengar, Madhusudan K.

Apparatus and method are provided for facilitating cooling of an electronic component. The apparatus includes a liquid-cooled cold plate and a thermal spreader associated with the cold plate. The cold plate includes multiple coolant-carrying channel sections extending within the cold plate, and a thermal conduction surface with a larger surface area than a surface area of the component to be cooled. The thermal spreader includes one or more heat pipes including multiple heat pipe sections. One or more heat pipe sections are partially aligned to a first region of the cold plate, that is, where aligned to the surface tomore » be cooled, and partially aligned to a second region of the cold plate, which is outside the first region. The one or more heat pipes facilitate distribution of heat from the electronic component to coolant-carrying channel sections of the cold plate located in the second region of the cold plate.« less

Cooled electronic system with liquid-cooled cold plate and thermal spreader coupled to electronic component

DOEpatents

Chainer, Timothy J.; Graybill, David P.; Iyengar, Madhusudan K.; Kamath, Vinod; Kochuparambil, Bejoy J.; Schmidt, Roger R.; Steinke, Mark E.

2016-08-09

Apparatus and method are provided for facilitating cooling of an electronic component. The apparatus includes a liquid-cooled cold plate and a thermal spreader associated with the cold plate. The cold plate includes multiple coolant-carrying channel sections extending within the cold plate, and a thermal conduction surface with a larger surface area than a surface area of the component to be cooled. The thermal spreader includes one or more heat pipes including multiple heat pipe sections. One or more heat pipe sections are partially aligned to a first region of the cold plate, that is, where aligned to the surface to be cooled, and partially aligned to a second region of the cold plate, which is outside the first region. The one or more heat pipes facilitate distribution of heat from the electronic component to coolant-carrying channel sections of the cold plate located in the second region of the cold plate.

Cooled electronic system with liquid-cooled cold plate and thermal spreader coupled to electronic component

DOEpatents

Chainer, Timothy J.; Graybill, David P.; Iyengar, Madhusudan K.; Kamath, Vinod; Kochuparambil, Bejoy J.; Schmidt, Roger R.; Steinke, Mark E.

2016-04-05

Apparatus and method are provided for facilitating cooling of an electronic component. The apparatus includes a liquid-cooled cold plate and a thermal spreader associated with the cold plate. The cold plate includes multiple coolant-carrying channel sections extending within the cold plate, and a thermal conduction surface with a larger surface area than a surface area of the component to be cooled. The thermal spreader includes one or more heat pipes including multiple heat pipe sections. One or more heat pipe sections are partially aligned to a first region of the cold plate, that is, where aligned to the surface to be cooled, and partially aligned to a second region of the cold plate, which is outside the first region. The one or more heat pipes facilitate distribution of heat from the electronic component to coolant-carrying channel sections of the cold plate located in the second region of the cold plate.

82 FR 57290 - Certain Memory Modules and Components Thereof Institution of Investigation

Federal Register 2010, 2011, 2012, 2013, 2014

2017-12-04

...Notice is hereby given that a complaint was filed with the U.S. International Trade Commission on October 31, 2017, under section 337 of the Tariff Act of 1930, as amended, on behalf of Netlist, Inc. of Irvine, California. A supplement to the complaint was filed on November 21, 2017. The complaint alleges violations of section 337 based upon the importation into the United States, the sale for importation, and the sale within the United States after importation of certain memory modules and components thereof by reason of infringement of certain claims of U.S. Patent No. 9,606,907 (``the '907 patent'') and U.S. Patent No. 9,535,623 (``the '623 patent''). The complaint further alleges that an industry in the United States exists or is in the process of being established as required by the applicable Federal Statute. The complainant requests that the Commission institute an investigation and, after the investigation, issue a limited exclusion order and a cease and desist order.

Shear-wave reflection imaging using a MEMS-based 3C landstreamer and a vertical impact source - an esker study in SW Finland

NASA Astrophysics Data System (ADS)

Brodic, Bojan; Malehmir, Alireza; Maries, Georgiana; Ahokangas, Elina; Mäkinen, Joni; Pasanen, Antti

2017-04-01

Higher resolution of S-wave seismic data compared to the P-wave ones are attractive for the researches working with the seismic methods. This is particularly true for near-surface applications due to significantly lower shear-wave velocities of unconsolidated sediments. Shear-wave imaging, however, poses certain restrictions on both source and receiver selections and also processing strategies. With three component (3C) seismic receivers becoming more affordable and used, shear-wave imaging from vertical sources is attracting more attention for near-surface applications. Theoretically, a vertical impact source will always excite both P- and S-waves although the excited S-waves are radially polarized (SV). There is an exchange of seismic energy between the vertical and radial component of the seismic wavefield. Additionally, it is theoretically accepted that there is no energy conversion or exchange from vertical into the transverse (or SH) component of the seismic wavefield, and the SH-waves can only be generated using SH sources. With the objectives of imaging esker structure (glacial sediments), water table and depth to bedrock, we conducted a seismic survey in Virttaankangas, in southwestern Finland. A bobcat-mounted vertical drop hammer (500 kg) was used as the seismic source. To obtain better source coupling, a 75×75×1.5 cm steel plate was mounted at the bottom of the hammer casing and all the hits made on this plate after placing it firmly on the ground at every shot point. For the data recording, we used a state-of-the-art comprising of 100 units, 240 m-long, 3C MEMS (micro electro-mechanical system) based seismic landstreamer developed at Uppsala University. Although the focus of the study was on the vertical component data, careful inspection of the transverse (SH) component of the raw data revealed clear shear wave reflections (normal moveout velocities ranging from 280-350 m/s at 50 m depth) on several shot gathers. This indicated potential for their analysis, hence shear-wave reflection imaging was carried out. Results show an excellent correspondence between the drilled depth to bedrock and the one independently obtained using P-wave first arrivals traveltime tomography with a reflection imaged on the stacked section of the SH component data. Aside from this reflection that follows the undulating bedrock topography, additional reflections are also observed on the stacked section that might be related to the sedimentary structures at the site. The section shows much finer resolution compared to the P-wave stacked section processed independently and reported earlier this year. This study illustrates the importance of 3C data recording and shows the potential of the landstreamer in imaging shallow subsurface using both P- and SH-waves generated from a vertical impact source. Whether the strong SH-wave energy observed is generated immediately at the source-ground contact, possible sliding of the base plate on which the impacts were made, an effect of near-surface heterogeneities or other factors remains to be carefully investigated. Acknowledgments: A contribution from Trust 2.2 project (http://trust-geoinfra.se) sponsored by Formas, BeFo, SBUF, SGU, Skanska, Tyréns, FQM, and NGI. We thank Turku Water Company, GTK and University of Turku, Department of Geography and Geology for supporting the data acquisition.

Prevalence of Metabolic Syndrome and Its Components among Japanese Workers by Clustered Business Category.

PubMed

Hidaka, Tomoo; Hayakawa, Takehito; Kakamu, Takeyasu; Kumagai, Tomohiro; Hiruta, Yuhei; Hata, Junko; Tsuji, Masayoshi; Fukushima, Tetsuhito

2016-01-01

The present study was a cross-sectional study conducted to reveal the prevalence of metabolic syndrome and its components and describe the features of such prevalence among Japanese workers by clustered business category using big data. The data of approximately 120,000 workers were obtained from a national representative insurance organization, and the study analyzed the health checkup and questionnaire results according to the field of business of each subject. Abnormalities found during the checkups such as excessive waist circumference, hypertension or glucose intolerance, and metabolic syndrome, were recorded. All subjects were classified by business field into 18 categories based on The North American Industry Classification System. Based on the criteria of the Japanese Committee for the Diagnostic Criteria of Metabolic Syndrome, the standardized prevalence ratio (SPR) of metabolic syndrome and its components by business category was calculated, and the 95% confidence interval of the SPR was computed. Hierarchical cluster analysis was then performed based on the SPR of metabolic syndrome components, and the 18 business categories were classified into three clusters for both males and females. The following business categories were at significantly high risk of metabolic syndrome: among males, Construction, Transportation, Professional Services, and Cooperative Association; and among females, Health Care and Cooperative Association. The results of the cluster analysis indicated one cluster for each gender with a higher prevalence of metabolic syndrome components; among males, a cluster consisting of Manufacturing, Transportation, Finance, and Cooperative Association, and among females, a cluster consisting of Mining, Transportation, Finance, Accommodation, and Cooperative Association. These findings reveal that, when providing health guidance and support regarding metabolic syndrome, consideration must be given to its components and the variety of its prevalence rates by business category and gender.

Prevalence of Metabolic Syndrome and Its Components among Japanese Workers by Clustered Business Category

PubMed Central

Hidaka, Tomoo; Hayakawa, Takehito; Kakamu, Takeyasu; Kumagai, Tomohiro; Hiruta, Yuhei; Hata, Junko; Tsuji, Masayoshi; Fukushima, Tetsuhito

2016-01-01

The present study was a cross-sectional study conducted to reveal the prevalence of metabolic syndrome and its components and describe the features of such prevalence among Japanese workers by clustered business category using big data. The data of approximately 120,000 workers were obtained from a national representative insurance organization, and the study analyzed the health checkup and questionnaire results according to the field of business of each subject. Abnormalities found during the checkups such as excessive waist circumference, hypertension or glucose intolerance, and metabolic syndrome, were recorded. All subjects were classified by business field into 18 categories based on The North American Industry Classification System. Based on the criteria of the Japanese Committee for the Diagnostic Criteria of Metabolic Syndrome, the standardized prevalence ratio (SPR) of metabolic syndrome and its components by business category was calculated, and the 95% confidence interval of the SPR was computed. Hierarchical cluster analysis was then performed based on the SPR of metabolic syndrome components, and the 18 business categories were classified into three clusters for both males and females. The following business categories were at significantly high risk of metabolic syndrome: among males, Construction, Transportation, Professional Services, and Cooperative Association; and among females, Health Care and Cooperative Association. The results of the cluster analysis indicated one cluster for each gender with a higher prevalence of metabolic syndrome components; among males, a cluster consisting of Manufacturing, Transportation, Finance, and Cooperative Association, and among females, a cluster consisting of Mining, Transportation, Finance, Accommodation, and Cooperative Association. These findings reveal that, when providing health guidance and support regarding metabolic syndrome, consideration must be given to its components and the variety of its prevalence rates by business category and gender. PMID:27082961

Site-specific Microzonation Study in Delhi Metropolitan City by 2-D Modelling of SH and P-SV Waves

NASA Astrophysics Data System (ADS)

Parvez, Imtiyaz A.; Vaccari, F.; Panza, G. F.

Delhi - the capital of India lies on a severe earthquake hazard threat not only from local earthquakes but also from Himalayan events just 200-250 km apart. The seismic ground motion in a part of Delhi City is computed with a hybrid technique based on the modal summation and the finite-difference scheme for site-specific strong ground motion modelling. Complete realistic SH and #E5/E5#-SV wave seismograms are computed along two geological cross sections, (1) north-south, from Inter State Bus Terminal (ISBT) to Sewanagar and (2) east-west, from Tilak Bridge to Punjabi Bagh. Two real earthquake sources of July 15, 1720 (MMI=IX, M=7.4) and August 27, 1960 (M=6.0) have been used in modelling. The response spectra ratio (RSR), i.e. the response spectra computed from the signals synthesized along the laterally varying section and normalized by the response spectra computed from the corresponding signals, synthesized for the bedrock reference regional model, have been determined. As expected, the sedimentary cover causes an increase of the signal amplitude, particularly in the radial and transverse components. To further check the site-effects, we reversed the source location to the other side of the cross section and recomputed the site amplifications. There are only a few sites where a large amplification is invariant with respect to the two source locations considered. The RSR ranges between 5 to 10 in the frequency range from 2.8 to 3.7 Hz for the radial and transverse components of motion along the NS cross section. Along the EW cross section RSR varies between 3.5 to 7.5 in the frequency range from 3.5 to 4.1 Hz. The amplification of the vertical component is considerable at high frequency (>4 Hz.) whereas it is negligible in lower frequency range.

Raman spectroscopic analysis of human skin tissue sections ex-vivo: evaluation of the effects of tissue processing and dewaxing

NASA Astrophysics Data System (ADS)

Ali, Syed M.; Bonnier, Franck; Tfayli, Ali; Lambkin, Helen; Flynn, Kathleen; McDonagh, Vincent; Healy, Claragh; Clive Lee, T.; Lyng, Fiona M.; Byrne, Hugh J.

2013-06-01

Raman spectroscopy coupled with K-means clustering analysis (KMCA) is employed to elucidate the biochemical structure of human skin tissue sections and the effects of tissue processing. Both hand and thigh sections of human cadavers were analyzed in their unprocessed and formalin-fixed, paraffin-processed (FFPP), and subsequently dewaxed forms. In unprocessed sections, KMCA reveals clear differentiation of the stratum corneum (SC), intermediate underlying epithelium, and dermal layers for sections from both anatomical sites. The SC is seen to be relatively rich in lipidic content; the spectrum of the subjacent layers is strongly influenced by the presence of melanin, while that of the dermis is dominated by the characteristics of collagen. For a given anatomical site, little difference in layer structure and biochemistry is observed between samples from different cadavers. However, the hand and thigh sections are consistently differentiated for all cadavers, largely based on lipidic profiles. In dewaxed FFPP samples, while the SC, intermediate, and dermal layers are clearly differentiated by KMCA of Raman maps of tissue sections, the lipidic contributions to the spectra are significantly reduced, with the result that respective skin layers from different anatomical sites become indistinguishable. While efficient at removing the fixing wax, the tissue processing also efficiently removes the structurally similar lipidic components of the skin layers. In studies of dermatological processes in which lipids play an important role, such as wound healing, dewaxed samples are therefore not appropriate. Removal of the lipids does however accentuate the spectral features of the cellular and protein components, which may be more appropriate for retrospective analysis of disease progression and biochemical analysis using tissue banks.

Structures of Mid-Polish Trough in the light of regional magnetotelluric survey

NASA Astrophysics Data System (ADS)

Stefaniuk, M.; Pokorski, J.; Wojdyla, M.; Klitynski, W.

2009-04-01

Introduction The magnetotelluric survey at three long regional profiles crossing the Mid-Polish Trough in north-western part of Poland was made during 2005-2008 period. Two of the profiles pass across the Pomeranian section of the Trough and the third one cuts its Kujawy section. The task of the survey was to recognize the geological structure of the contact zone of Precambrian East European Craton and Paleozoic Platform of Western Europe. The profiles crossed major geological structures of central and north-western Poland, including the Variscan Externides and Varscian Foredeep, the Transeuropean Suture Zone and the marginal zone of the East European Craton. The main objectives of the project included evaluation of resistivity distribution and identification of structures of sub-Zechstein sedimentary and metamorphic complexes.The screening of seismic energy by high reflective Zechstein evaporates is the main problem in identifying the sub-Zechstein complexes in the Polish Lowlands area. Since evaporates do not screen the electromagnetic waves, the magnetotelluric method can be advantageously applied. The sub-Zechstein complexes and structures are commonly considered as hydrocarbon prospective. A lot of gas deposits have been discovered in Rotliegend sediments in central and Western Europe. A number offshore and onshore oil fields were found in Cambrian sandstones in the Baltic Sea area. Techniques and methodology of surveys Magnetotelluric measurements were taken with the use of MT-1 system of Electromagnetic Instruments Incorporation (EMI), Richmond, California, USA and System 2000.net based on V8 receiver of Phoenix Geophysics Ltd., Ottawa, Canada. An average spacing of sounding sites was about 4 km. The components of natural electromagnetic field were recorded over a broad range of frequencies, ranging from 0.0003 Hz to 575 Hz (MT-1) and 0,0003 HZ to 10 000,0 HZ (System 2000.net). This frequency band allowed information on the geology from a depth range of a few dozen meters to approximately 100 km to be obtained. A remote reference site was located at a distance of over 100 km of the study area. Data processing and interpretation Processing of the recorded data included the estimation of the components of impedance tensor (Zxx, Zxy, Zyx and Zyy ), with the use of robust procedures. The components of the impedance tensor enabled calculation of field curves for two orientations of the measurement system and additional parameters of the medium like skew, strike, pole diagrams etc. Recording of the vertical component of electromagnetic field (Hz) enabled the tipper parameter, T, to be calculated. Geophysical interpretation of MT sounding data along profiles was based on 1D inversion and 2D inversion. The upper part of the geological section is built of relatively flat layers; hence a 1D interpretation model could be effectively applied. Starting models for 1D inversion were constructed based on results of electromagnetic well-logging data. Some well-documented seismic horizons were taken as constraints in 1D inversion. The first step in 2D MT inversion was the calculation of inverse model with stabilized parameters of the upper part of geological section over the top of Zechstein complex. The starting model was obtained with the use of available geological cross-sections interpreted based on borehole and reflection seismic data. Results of inversion for the lower part of the section with constrained its upper part made some misfits between calculated and post-processed magnetotelluric curves. The second step in geophysical interpretation was 2D inversion with no constraints, which was finished when the misfit was small. Results of the first step of 2D inversion were applied as a starting model. Depending on inversion parameters, final resistivity distribution model along profiles was obtained. Geological interpretation was made based on resistivity cross-sections and borehole and reflection seismic data. Of great interest is varied resistivity of the formation resting below the Zechstein evaporate complex. As a result of data interpretation geophysical and geological sections were constructed. Conclusions As a result of magnetotelluric data interpretation, a tectonic model along measurement profiles with fault zones was constructed and lithology differentiation of sub-Zechstein complex was determined. Deep magnetotelluric cross-sections with interpretation of sub-Zechstein structures across the Polish Lowlands help to understand geodynamic processes in the area. Acknowledgments. This paper was based on results of investigations carried out by the PBG Geophysical Exploration Company Ltd. financed by Ministry of Environment trough National Fund for Environment Protection and Water Resources. The authors used also results of statutory research of Department of General Geology, Environment Protection and Geotourism, UST AGH, financed by the Minister of Science and Higher Education (project no 11.11.140.447). Interpretation was carried out using software by EMI, and Geosystem WingLinkTM.

A Comparative Study of the Proposed Models for the Components of the National Health Information System

PubMed Central

Ahmadi, Maryam; Damanabi, Shahla; Sadoughi, Farahnaz

2014-01-01

Introduction: National Health Information System plays an important role in ensuring timely and reliable access to Health information, which is essential for strategic and operational decisions that improve health, quality and effectiveness of health care. In other words, using the National Health information system you can improve the quality of health data, information and knowledge used to support decision making at all levels and areas of the health sector. Since full identification of the components of this system – for better planning and management influential factors of performanceseems necessary, therefore, in this study different attitudes towards components of this system are explored comparatively. Methods: This is a descriptive and comparative kind of study. The society includes printed and electronic documents containing components of the national health information system in three parts: input, process and output. In this context, search for information using library resources and internet search were conducted, and data analysis was expressed using comparative tables and qualitative data. Results: The findings showed that there are three different perspectives presenting the components of national health information system Lippeveld and Sauerborn and Bodart model in 2000, Health Metrics Network (HMN) model from World Health Organization in 2008, and Gattini’s 2009 model. All three models outlined above in the input (resources and structure) require components of management and leadership, planning and design programs, supply of staff, software and hardware facilities and equipment. Plus, in the “process” section from three models, we pointed up the actions ensuring the quality of health information system, and in output section, except for Lippeveld Model, two other models consider information products and use and distribution of information as components of the national health information system. Conclusion: the results showed that all the three models have had a brief discussion about the components of health information in input section. But Lippeveld model has overlooked the components of national health information in process and output sections. Therefore, it seems that the health measurement model of network has a comprehensive presentation for the components of health system in all three sections-input, process and output. PMID:24825937

A comparative study of the proposed models for the components of the national health information system.

PubMed

Ahmadi, Maryam; Damanabi, Shahla; Sadoughi, Farahnaz

2014-04-01

National Health Information System plays an important role in ensuring timely and reliable access to Health information, which is essential for strategic and operational decisions that improve health, quality and effectiveness of health care. In other words, using the National Health information system you can improve the quality of health data, information and knowledge used to support decision making at all levels and areas of the health sector. Since full identification of the components of this system - for better planning and management influential factors of performanceseems necessary, therefore, in this study different attitudes towards components of this system are explored comparatively. This is a descriptive and comparative kind of study. The society includes printed and electronic documents containing components of the national health information system in three parts: input, process and output. In this context, search for information using library resources and internet search were conducted, and data analysis was expressed using comparative tables and qualitative data. The findings showed that there are three different perspectives presenting the components of national health information system Lippeveld and Sauerborn and Bodart model in 2000, Health Metrics Network (HMN) model from World Health Organization in 2008, and Gattini's 2009 model. All three models outlined above in the input (resources and structure) require components of management and leadership, planning and design programs, supply of staff, software and hardware facilities and equipment. Plus, in the "process" section from three models, we pointed up the actions ensuring the quality of health information system, and in output section, except for Lippeveld Model, two other models consider information products and use and distribution of information as components of the national health information system. the results showed that all the three models have had a brief discussion about the components of health information in input section. But Lippeveld model has overlooked the components of national health information in process and output sections. Therefore, it seems that the health measurement model of network has a comprehensive presentation for the components of health system in all three sections-input, process and output.

The approach for shortest paths in fire succor based on component GIS technology

NASA Astrophysics Data System (ADS)

Han, Jie; Zhao, Yong; Dai, K. W.

2007-06-01

Fire safety is an important issue for the national economy and people's living. Efficiency and exactness of fire department succor directly relate to safety of peoples' lives and property. Many disadvantages of the traditional fire system have been emerged in practical applications. The preparation of pumpers is guided by wireless communication or wire communication, so its real-time and accurate performances are much poorer. The information about the reported fire, such as the position, disaster and map, et al., for alarm and command was processed by persons, which slows the reaction speed and delays the combat opportunity. In order to solve these disadvantages, it has an important role to construct a modern fire command center based on high technology. The construction of modern fire command center can realize the modernization and automation of fire command and management. It will play a great role in protecting safety of peoples' lives and property. The center can enhance battle ability and can reduce the direct and indirect loss of fire damage at most. With the development of science technology, Geographic Information System (GIS) has becoming a new information industry for hardware production, software development, data collection, space analysis and counseling. With the popularization of computers and the development of GIS, GIS has gained increasing broad applications for its strong functionality. Network analysis is one of the most important functions of GIS, and the most elementary and pivotal issue of network analysis is the calculation of shortest paths. The shortest paths are mostly applied to some emergent systems such as 119 fire alarms. These systems mainly require that the computation time of the optimal path should be 1-3 seconds. And during traveling, the next running path of the vehicles should be calculated in time. So the implement of the shortest paths must have a high efficiency. In this paper, the component GIS technology was applied to collect and record the data information (such as, the situation of this disaster, map and road status et al) of the reported fire firstly. The ant colony optimization was used to calculate the shortest path of fire succor secondly. The optimization results were sent to the pumpers, which can let pumpers choose the shortest paths intelligently and come to fire position with least time. The programming method for shortest paths is proposed in section 3. There are three parts in this section. The elementary framework of the proposed programming method is presented in part one. The systematic framework of GIS component is described in part two. The ant colony optimization employed is presented in part three. In section 4, a simple application instance was presented to demonstrate the proposed programming method. There are three parts in this section. The distributed Web application based on component GIS was described in part one. The optimization results without traffic constraint were presented in part two. The optimization results with traffic constraint were presented in part three. The contributions of this paper can be summarized as follows. (1) It proposed an effective approach for shortest paths in fire succor based on component GIS technology. This proposed approach can achieve the real-time decisions of shortest paths for fire succor. (2) It applied the ant colony optimization to implement the shortest path decision. The traffic information was considered in the shortest path decision using ant colony optimization. The final application instance suggests that the proposed approach is feasible, correct and valid.

Inequalities in the spiritual health of young Canadians: a national, cross-sectional study.

PubMed

Michaelson, Valerie; Freeman, John; King, Nathan; Ascough, Hannah; Davison, Colleen; Trothen, Tracy; Phillips, Sian; Pickett, William

2016-11-28

Spiritual health, along with physical, emotional, and social aspects, is one of four domains of health. Assessment in this field of research is challenging methodologically. No contemporary population-based studies have profiled the spiritual health of adolescent Canadians with a focus on health inequalities. In a 2014 nationally representative sample of Canadians aged 11-15 years we therefore: (1) psychometrically evaluated a series of items used to assess the perceived importance of spiritual health and its four potential sub-domains (connections with: self, others, nature and the natural environment, and the transcendent) to adolescents; (2) described potential inequalities in spiritual health within adolescent populations, overall and by spiritual health sub-domain, by key socio-demographic factors. Cross-sectional analysis of survey reports from the 2014 (Cycle 7) of the Canadian Health Behaviour in School-aged Children study (weighted n = 25,036). Principal components analysis followed by confirmatory factor analysis were used to explore the psychometric properties of the spiritual health items and the associated composite scale describing perceived importance of spiritual health. Associations among this composite scale, its individual sub-domains, and key socio-demographic factors were then explored. The principal components analysis best supported a four-factor structure where the eight scale items loaded highly according to the original four domains. This was also supported in confirmatory factor analyses. We then combined the eight items into composite spiritual health score as supported by theory, principal components analysis findings, and acceptable tests of reliability. Further confirmatory factor analysis suggested the need for additional refinements to this scale. Based upon exploratory cross-sectional analyses, strong socio-demographic inequalities were observed in the spiritual health measures by age, gender, relative material wealth, immigration status, and province/territory. Study findings highlight potential inequalities in the spiritual health of young Canadians, as well as opportunities for methodological advances in the assessment of adolescent spiritual health in our population.

Thin Film Ceramic Strain Sensor Development for High Temperature Environments

NASA Technical Reports Server (NTRS)

Wrbanek, John D.; Fralick, Gustave C.; Gonzalez, Jose M.; Laster, Kimala L.

2008-01-01

The need for sensors to operate in harsh environments is illustrated by the need for measurements in the turbine engine hot section. The degradation and damage that develops over time in hot section components can lead to catastrophic failure. At present, the degradation processes that occur in the harsh hot section environment are poorly characterized, which hinders development of more durable components, and since it is so difficult to model turbine blade temperatures, strains, etc, actual measurements are needed. The need to consider ceramic sensing elements is brought about by the temperature limits of metal thin film sensors in harsh environments. The effort at the NASA Glenn Research Center (GRC) to develop high temperature thin film ceramic static strain gauges for application in turbine engines is described, first in the fan and compressor modules, and then in the hot section. The near-term goal of this research effort was to identify candidate thin film ceramic sensor materials and provide a list of possible thin film ceramic sensor materials and corresponding properties to test for viability. A thorough literature search was conducted for ceramics that have the potential for application as high temperature thin film strain gauges chemically and physically compatible with the NASA GRCs microfabrication procedures and substrate materials. Test results are given for tantalum, titanium and zirconium-based nitride and oxynitride ceramic films.

Experimental investigation on the thermal performance of Si micro-heat pipe with different cross-sections

NASA Astrophysics Data System (ADS)

Hamidnia, Mohammad; Luo, Yi; Wang, Xiaodong; Li, Congming

2017-10-01

Increasing component densities of the integrated circuit (IC) and packaging levels has led to thermal management problems. Si substrates with embedded micro-heat pipes (MHPs) couple good thermal characteristics and cost savings associated with IC batch processing. The thermal performance of MHP is intimately related to the cross-sectional geometry. Different cross-sections are designed in order to enhance the backflow of working fluid. In this experimental study, three different Si MHPs with same hydraulic diameter and various cross-sections are fabricated by micro-fabrication methods and tested under different conditions of fluid charge ratios. The results show that the trapezoidal MHP associated with rectangular artery which is charged with 40% of vapor chamber’s volume has the best thermal performance. This silicon-based MHP is a passive approach for thermal management, which could widen applications in the commercial electronics industry and LED lightings.

Power system applications of fiber optics

NASA Technical Reports Server (NTRS)

Kirkham, H.; Johnston, A.; Lutes, G.; Daud, T.; Hyland, S.

1984-01-01

Power system applications of optical systems, primarily using fiber optics, are reviewed. The first section reviews fibers as components of communication systems. The second section deals with fiber sensors for power systems, reviewing the many ways light sources and fibers can be combined to make measurements. Methods of measuring electric field gradient are discussed. Optical data processing is the subject of the third section, which begins by reviewing some widely different examples and concludes by outlining some potential applications in power systems: fault location in transformers, optical switching for light fired thyristors and fault detection based on the inherent symmetry of most power apparatus. The fourth and final section is concerned with using optical fibers to transmit power to electric equipment in a high voltage situation, potentially replacing expensive high voltage low power transformers. JPL has designed small photodiodes specifically for this purpose, and fabricated and tested several samples. This work is described.

On 3-D inelastic analysis methods for hot section components. Volume 1: Special finite element models

NASA Technical Reports Server (NTRS)

Nakazawa, S.

1987-01-01

This Annual Status Report presents the results of work performed during the third year of the 3-D Inelastic Analysis Methods for Hot Section Components program (NASA Contract NAS3-23697). The objective of the program is to produce a series of new computer codes that permit more accurate and efficient three-dimensional analysis of selected hot section components, i.e., combustor liners, turbine blades, and turbine vanes. The computer codes embody a progression of mathematical models and are streamlined to take advantage of geometrical features, loading conditions, and forms of material response that distinguish each group of selected components. This report is presented in two volumes. Volume 1 describes effort performed under Task 4B, Special Finite Element Special Function Models, while Volume 2 concentrates on Task 4C, Advanced Special Functions Models.

40 CFR 94.211 - Emission-related maintenance instructions for purchasers.

Code of Federal Regulations, 2010 CFR

2010-07-01

... the Administrator's satisfaction that the engine will function properly only if the component or... section are defined as critical emission-related components. (i) Catalytic convertor. (ii) Electronic... which satisfy one of the conditions defined in paragraphs (j)(2)(i) through (j)(2)(vi) of this section...

18 CFR 367.51 - Components of construction.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 18 Conservation of Power and Water Resources 1 2010-04-01 2010-04-01 false Components of construction. 367.51 Section 367.51 Conservation of Power and Water Resources FEDERAL ENERGY REGULATORY... in other items in this section. (3)(i) Materials and supplies includes the purchase price at the...

48 CFR 44.400 - Scope of subpart.

Code of Federal Regulations, 2010 CFR

2010-10-01

... SUBCONTRACTING POLICIES AND PROCEDURES Subcontracts for Commercial Items and Commercial Components 44.400 Scope... required to apply to any subcontractors that are furnishing commercial items or commercial components in accordance with Section 8002(b)(2) of Public Law 103-355 and Section 826 of Public Law 110-181 (10 U.S.C...

Reading and Math.

ERIC Educational Resources Information Center

Baldwin, Anna; And Others

This publication contains materials used in the three phases of the reading and mathematics components of work-specific classes. Each section begins with an overview of developments in that phase. Section 1 focuses on Phase 1 during which math and reading were taught as separate components. It contains a math placement appraisal, worksheets and…

Heat transfer to two-phase air/water mixtures flowing in small tubes with inlet disequilibrium

NASA Technical Reports Server (NTRS)

Janssen, J. M.; Florschuetz, L. W.; Fiszdon, J. P.

1986-01-01

The cooling of gas turbine components was the subject of considerable research. The problem is difficult because the available coolant, compressor bleed air, is itself quite hot and has relatively poor thermophysical properties for a coolant. Injecting liquid water to evaporatively cool the air prior to its contact with the hot components was proposed and studied, particularly as a method of cooling for contingency power applications. Injection of a small quantity of cold liquid water into a relatively hot coolant air stream such that evaporation of the liquid is still in process when the coolant contacts the hot component was studied. No approach was found whereby heat transfer characteristics could be confidently predicted for such a case based solely on prior studies. It was not clear whether disequilibrium between phases at the inlet to the hot component section would improve cooling relative to that obtained where equilibrium was established prior to contact with the hot surface.

Reactive Distillation for Esterification of Bio-based Organic Acids

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fields, Nathan; Miller, Dennis J.; Asthana, Navinchandra S.

2008-09-23

The following is the final report of the three year research program to convert organic acids to their ethyl esters using reactive distillation. This report details the complete technical activities of research completed at Michigan State University for the period of October 1, 2003 to September 30, 2006, covering both reactive distillation research and development and the underlying thermodynamic and kinetic data required for successful and rigorous design of reactive distillation esterification processes. Specifically, this project has led to the development of economical, technically viable processes for ethyl lactate, triethyl citrate and diethyl succinate production, and on a larger scalemore » has added to the overall body of knowledge on applying fermentation based organic acids as platform chemicals in the emerging biorefinery. Organic acid esters constitute an attractive class of biorenewable chemicals that are made from corn or other renewable biomass carbohydrate feedstocks and replace analogous petroleum-based compounds, thus lessening U.S. dependence on foreign petroleum and enhancing overall biorefinery viability through production of value-added chemicals in parallel with biofuels production. Further, many of these ester products are candidates for fuel (particularly biodiesel) components, and thus will serve dual roles as both industrial chemicals and fuel enhancers in the emerging bioeconomy. The technical report from MSU is organized around the ethyl esters of four important biorenewables-based acids: lactic acid, citric acid, succinic acid, and propionic acid. Literature background on esterification and reactive distillation has been provided in Section One. Work on lactic acid is covered in Sections Two through Five, citric acid esterification in Sections Six and Seven, succinic acid in Section Eight, and propionic acid in Section Nine. Section Ten covers modeling of ester and organic acid vapor pressure properties using the SPEAD (Step Potential Equilibrium and Dynamics) method.« less

The extinction properties of forest components

NASA Technical Reports Server (NTRS)

Karam, M. A.; Fung, A. K.; Blanchard, A. J.; Nance, C. E.

1988-01-01

The effect of each forest component on the extinction of electromagnetic waves is investigated by modeling the branches with finite cylinders, deciduous leaves with elliptic disks, and coniferous leaves with needles. The inner field is estimated by the field inside an infinitely long cylinder of similar properties for the branches, and by the Shifrin approximation for the leaves. For each forest component analytic expressions were derived for the extinction cross section via the forward scattering theorem and for ohmic and scattered losses. For branches, the variation of the extinction cross section obtained via the forward scattering theorem is illustrated numerically as a function of the branch radius and the imaginery part of its dielectric constant. It is compared with the measurements from a single branch. For the leaves, the forward scattering theorem gives value for the extinction cross section equal to the ohmic cross section.

Integrated Instrumentation and Sensor Systems Enabling Condition-Based Maintenance of Aerospace Equipment

DTIC Science & Technology

2012-01-01

systems . For some specific sensor requirements in the domains considered here, for example, assessing system behavior and component state in gas turbine ...Cost Objectives. In general , the implication of the suitability and life cycle cost [LCC] driven objectives for integrated instrumentation/sensor system ...section should be considered. In general , the systems engineering approach provided clear benefits in defining user significant IISS system requirements and

Gender Differences in the Prevalence of Metabolic Syndrome and Its Components among Adults with Disabilities Based on a Community Health Check Up Data

ERIC Educational Resources Information Center

Lin, Jin-Ding; Lin, Lan-Ping; Liou, Shih-Wen; Chen, Yu-Chung; Hsu, Shang-Wei; Liu, Chien-Ting

2013-01-01

Metabolic syndrome is highly prevalent in society gradually and has important implications for public health in recent years. The present study aims to examine the gender effect on the prevalence of metabolic syndrome among adults with disabilities. A cross-sectional study was conduct to analyze annual health check-up chart of 419 people with…

78 FR 79480 - Notice of Receipt of Complaint; Solicitation of Comments Relating to the Public Interest

Federal Register 2010, 2011, 2012, 2013, 2014

2013-12-30

...Notice is hereby given that the U.S. International Trade Commission has received a complaint entitled Certain Vision-Based Driver Assistance System Cameras and Components Thereof, DN 2993; the Commission is soliciting comments on any public interest issues raised by the complaint or complainant's filing under section 210.8(b) of the Commission's Rules of Practice and Procedure (19 CFR 210.8(b)).

14 CFR 23.994 - Fuel system components.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Fuel system components. 23.994 Section 23... AIRWORTHINESS STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Powerplant Fuel System Components § 23.994 Fuel system components. Fuel system components in an engine nacelle or in the fuselage...

14 CFR 25.994 - Fuel system components.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Fuel system components. 25.994 Section 25... AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Powerplant Fuel System Components § 25.994 Fuel system components. Fuel system components in an engine nacelle or in the fuselage must be protected from damage...

14 CFR 23.994 - Fuel system components.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Fuel system components. 23.994 Section 23... AIRWORTHINESS STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Powerplant Fuel System Components § 23.994 Fuel system components. Fuel system components in an engine nacelle or in the fuselage...

14 CFR 23.994 - Fuel system components.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Fuel system components. 23.994 Section 23... AIRWORTHINESS STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Powerplant Fuel System Components § 23.994 Fuel system components. Fuel system components in an engine nacelle or in the fuselage...

14 CFR 23.994 - Fuel system components.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Fuel system components. 23.994 Section 23... AIRWORTHINESS STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Powerplant Fuel System Components § 23.994 Fuel system components. Fuel system components in an engine nacelle or in the fuselage...

14 CFR 25.994 - Fuel system components.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Fuel system components. 25.994 Section 25... AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Powerplant Fuel System Components § 25.994 Fuel system components. Fuel system components in an engine nacelle or in the fuselage must be protected from damage...

14 CFR 25.994 - Fuel system components.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Fuel system components. 25.994 Section 25... AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Powerplant Fuel System Components § 25.994 Fuel system components. Fuel system components in an engine nacelle or in the fuselage must be protected from damage...

14 CFR 25.994 - Fuel system components.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Fuel system components. 25.994 Section 25... AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Powerplant Fuel System Components § 25.994 Fuel system components. Fuel system components in an engine nacelle or in the fuselage must be protected from damage...

14 CFR 23.994 - Fuel system components.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Fuel system components. 23.994 Section 23... AIRWORTHINESS STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Powerplant Fuel System Components § 23.994 Fuel system components. Fuel system components in an engine nacelle or in the fuselage...

14 CFR 25.994 - Fuel system components.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Fuel system components. 25.994 Section 25... AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Powerplant Fuel System Components § 25.994 Fuel system components. Fuel system components in an engine nacelle or in the fuselage must be protected from damage...

Nonperturbative contributions to a resummed leptonic angular distribution in inclusive neutral vector boson production

NASA Astrophysics Data System (ADS)

Guzzi, Marco; Nadolsky, Pavel M.; Wang, Bowen

2014-07-01

We present an analysis of nonperturbative contributions to the transverse momentum distribution of Z/γ* bosons produced at hadron colliders. The new data on the angular distribution ϕη* of Drell-Yan pairs measured at the Tevatron are shown to be in excellent agreement with a perturbative QCD prediction based on the Collins-Soper-Sterman (CSS) resummation formalism at next-to-next-to-leading logarithmic (NNLL) accuracy. Using these data, we determine the nonperturbative component of the CSS resummed cross section and estimate its dependence on arbitrary resummation scales and other factors. With the scale dependence included at the NNLL level, a significant nonperturbative component is needed to describe the angular data.

Introduction. ERIC Processing Manual, Section I.

ERIC Educational Resources Information Center

Brandhorst, Ted, Ed.

This document describes the major organizational components of the Educational Resources Information Center (ERIC) system, the interactions between those components, and the major products and services provided by those components. (WTB)

Electromagnetic absorption properties of spacecraft and space debris

NASA Astrophysics Data System (ADS)

Micheli, D.; Santoni, F.; Giusti, A.; Delfini, A.; Pastore, R.; Vricella, A.; Albano, M.; Arena, L.; Piergentili, F.; Marchetti, M.

2017-04-01

Aim of the work is to present a method to evaluate the electromagnetic absorption properties of spacecraft and space debris. For these objects, the radar detection ability depends mainly on volume, shape, materials type and other electromagnetic reflecting behaviour of spacecraft surface components, such as antennas or thermal blankets, and of metallic components in space debris. The higher the electromagnetic reflection coefficient of such parts, the greater the radar detection possibility. In this research an electromagnetic reverberation chamber is used to measure the absorption cross section (ACS) of four objects which may represent space structure operating components as well as examples of space debris: a small satellite, a composite antenna dish, a Thermal Protection System (TPS) tile and a carbon-based composite missile shell. The ACS mainly depends on geometrical characteristics like apertures, face numbers and bulk porosity, as well as on the type of the material itself. The ACS, which is an electromagnetic measurement, is expressed in squared meters and thus can be compared with the objects geometrical cross section. A small ACS means a quite electromagnetic reflective tendency, which is beneficial for radar observations; on the contrary, high values of ACS indicate a strong absorption of the electromagnetic field, which in turn can result a critical hindering of radar tracking.

HIGH DIMENSIONAL COVARIANCE MATRIX ESTIMATION IN APPROXIMATE FACTOR MODELS

PubMed Central

Fan, Jianqing; Liao, Yuan; Mincheva, Martina

2012-01-01

The variance covariance matrix plays a central role in the inferential theories of high dimensional factor models in finance and economics. Popular regularization methods of directly exploiting sparsity are not directly applicable to many financial problems. Classical methods of estimating the covariance matrices are based on the strict factor models, assuming independent idiosyncratic components. This assumption, however, is restrictive in practical applications. By assuming sparse error covariance matrix, we allow the presence of the cross-sectional correlation even after taking out common factors, and it enables us to combine the merits of both methods. We estimate the sparse covariance using the adaptive thresholding technique as in Cai and Liu (2011), taking into account the fact that direct observations of the idiosyncratic components are unavailable. The impact of high dimensionality on the covariance matrix estimation based on the factor structure is then studied. PMID:22661790

Improved LED backlight with unique color and intensity control and NVIS capability

NASA Astrophysics Data System (ADS)

Herman, Robert; Zagar, Pete; Ulijasz, Ted; Hansen, Hans C.; Ellner, Fred

2006-05-01

Currently deployed conventional flat panel AMLCD displays employ fluorescent lamp backlights to achieve the required lighting levels for cockpits in high performance aircraft. Advances have been made in backlighting technology by replacing fluorescent lamps with high performance LEDs. However, these new LED-based backlights are lacking in control of color and luminance intensity especially when related to NVIS requirements in a cockpit. This paper describes a unique integration of LED, electronic, and optical components to meet the requirements of high performance aircraft over their extreme range of operating environments. The LED-based backlight utilizes state-of-art components to enable daylight, night, and NVIS requirements to be implemented in a simple cost-effective package. The performance results presented highlight the advantages of this new design when compared to currently available backlighting designs. Techniques as described in section 2 of this paper are covered under patent application to the US and International Patent Offices.

Progress in SiC/SiC Ceramic Composite Development for Gas Turbine Hot-Section Components under NASA EPM and UEET Programs

NASA Technical Reports Server (NTRS)

DiCarlo, J. A.; Yun, Hee Mann; Morscher, Gregory N.; Bhatt, Ramakrishna T.

2002-01-01

The successful application of ceramic matrix composites as hot-section components in advanced gas turbine engines will require the development of constituent materials and processes that can provide the material systems with the key thermostructural properties required for long-term component service. Much initial progress in identifying these materials and processes was made under the former NASA Enabling Propulsion Materials Program using stoichiometric Sylramic (trademark) silicon-carbide (SiC) fibers, 2D (two dimensional)-woven fiber architectures, chemically vapor-infiltrated (CVI) BN fiber coatings (interphases), and SiC-based matrices containing CVI SiC interphase over-coatings, slurry-infiltrated SiC particulate, and melt-infiltrated (MI) silicon. The objective of this paper is to discuss the property benefits of this SiC/SiC composite system for high-temperature engine components and to elaborate on further progress in SiC/SiC development made under the new NASA Ultra Efficient Engine Technology Program. This progress stems from the recent development of advanced constituent materials and manufacturing processes, including specific treatments at NASA that improve the creep, rupture, and environmental resistance of the Sylramic fiber as well as the thermal conductivity and creep resistance of the CVI SiC over-coatings. Also discussed are recent observations concerning the detrimental effects of inadvertent carbon in the fiber-BN interfacial region and the beneficial effects of certain 2D-architectures for thin-walled SiC/SiC panels.

Development and Property Evaluation of Selected HfO2-Silicon and Rare Earth-Silicon Based Bond Coats and Environmental Barrier Coating Systems for SiC/SiC Ceramic Matrix Composites

NASA Technical Reports Server (NTRS)

Zhu, Dongming

2016-01-01

Ceramic environmental barrier coatings (EBC) and SiC/SiC ceramic matrix composites (CMCs) will play a crucial role in future aircraft propulsion systems because of their ability to significantly increase engine operating temperatures, improve component durability, reduce engine weight and cooling requirements. Advanced EBC systems for SiC/SiC CMC turbine and combustor hot section components are currently being developed to meet future turbine engine emission and performance goals. One of the significant material development challenges for the high temperature CMC components is to develop prime-reliant, high strength and high temperature capable environmental barrier coating bond coat systems, since the current silicon bond coat cannot meet the advanced EBC-CMC temperature and stability requirements. In this paper, advanced NASA HfO2-Si and rare earth Si based EBC bond coat EBC systems for SiC/SiC CMC combustor and turbine airfoil applications are investigated. High temperature properties of the advanced EBC systems, including the strength, fracture toughness, creep and oxidation resistance have been studied and summarized. The advanced NASA EBC systems showed some promise to achieve 1500C temperature capability, helping enable next generation turbine engines with significantly improved engine component temperature capability and durability.

Production of Diesel Engine Turbocharger Turbine from Low Cost Titanium Powder

DOE Office of Scientific and Technical Information (OSTI.GOV)

Muth, T. R.; Mayer, R.

2012-05-04

Turbochargers in commercial turbo-diesel engines are multi-material systems where usually the compressor rotor is made of aluminum or titanium based material and the turbine rotor is made of either a nickel based superalloy or titanium, designed to operate under the harsh exhaust gas conditions. The use of cast titanium in the turbine section has been used by Cummins Turbo Technologies since 1997. Having the benefit of a lower mass than the superalloy based turbines; higher turbine speeds in a more compact design can be achieved with titanium. In an effort to improve the cost model, and develop an industrial supplymore » of titanium componentry that is more stable than the traditional aerospace based supply chain, the Contractor has developed component manufacturing schemes that use economical Armstrong titanium and titanium alloy powders and MgR-HDH powders. Those manufacturing schemes can be applied to compressor and turbine rotor components for diesel engine applications with the potential of providing a reliable supply of titanium componentry with a cost and performance advantage over cast titanium.« less

Joining and Integration of Silicon Carbide-Based Materials for High Temperature Applications

NASA Technical Reports Server (NTRS)

Halbig, Michael C.; Singh, Mrityunjay

2016-01-01

Advanced joining and integration technologies of silicon carbide-based ceramics and ceramic matrix composites are enabling for their implementation into wide scale aerospace and ground-based applications. The robust joining and integration technologies allow for large and complex shapes to be fabricated and integrated with the larger system. Potential aerospace applications include lean-direct fuel injectors, thermal actuators, turbine vanes, blades, shrouds, combustor liners and other hot section components. Ground based applications include components for energy and environmental systems. Performance requirements and processing challenges are identified for the successful implementation different joining technologies. An overview will be provided of several joining approaches which have been developed for high temperature applications. In addition, various characterization approaches were pursued to provide an understanding of the processing-microstructure-property relationships. Microstructural analysis of the joint interfaces was conducted using optical, scanning electron, and transmission electron microscopy to identify phases and evaluate the bond quality. Mechanical testing results will be presented along with the need for new standardized test methods. The critical need for tailoring interlayer compositions for optimum joint properties will also be highlighted.

Model-based recursive partitioning to identify risk clusters for metabolic syndrome and its components: findings from the International Mobility in Aging Study

PubMed Central

Pirkle, Catherine M; Wu, Yan Yan; Zunzunegui, Maria-Victoria; Gómez, José Fernando

2018-01-01

Objective Conceptual models underpinning much epidemiological research on ageing acknowledge that environmental, social and biological systems interact to influence health outcomes. Recursive partitioning is a data-driven approach that allows for concurrent exploration of distinct mixtures, or clusters, of individuals that have a particular outcome. Our aim is to use recursive partitioning to examine risk clusters for metabolic syndrome (MetS) and its components, in order to identify vulnerable populations. Study design Cross-sectional analysis of baseline data from a prospective longitudinal cohort called the International Mobility in Aging Study (IMIAS). Setting IMIAS includes sites from three middle-income countries—Tirana (Albania), Natal (Brazil) and Manizales (Colombia)—and two from Canada—Kingston (Ontario) and Saint-Hyacinthe (Quebec). Participants Community-dwelling male and female adults, aged 64–75 years (n=2002). Primary and secondary outcome measures We apply recursive partitioning to investigate social and behavioural risk factors for MetS and its components. Model-based recursive partitioning (MOB) was used to cluster participants into age-adjusted risk groups based on variabilities in: study site, sex, education, living arrangements, childhood adversities, adult occupation, current employment status, income, perceived income sufficiency, smoking status and weekly minutes of physical activity. Results 43% of participants had MetS. Using MOB, the primary partitioning variable was participant sex. Among women from middle-incomes sites, the predicted proportion with MetS ranged from 58% to 68%. Canadian women with limited physical activity had elevated predicted proportions of MetS (49%, 95% CI 39% to 58%). Among men, MetS ranged from 26% to 41% depending on childhood social adversity and education. Clustering for MetS components differed from the syndrome and across components. Study site was a primary partitioning variable for all components except HDL cholesterol. Sex was important for most components. Conclusion MOB is a promising technique for identifying disease risk clusters (eg, vulnerable populations) in modestly sized samples. PMID:29500203

Gas mixtures for gas-filled radiation detectors

DOEpatents

Christophorou, Loucas G.; McCorkle, Dennis L.; Maxey, David V.; Carter, James G.

1982-01-05

Improved binary and ternary gas mixtures for gas-filled radiation detectors are provided. The components are chosen on the basis of the principle that the first component is one molecular gas or mixture of two molecular gases having a large electron scattering cross section at energies of about 0.5 eV and higher, and the second component is a noble gas having a very small cross section at and below about 1.0 eV, whereby fast electrons in the gaseous mixture are slowed into the energy range of about 0.5 eV where the cross section for the mixture is small and hence the electron mean free path is large. The reduction in both the cross section and the electron energy results in an increase in the drift velocity of the electrons in the gas mixtures over that for the separate components for a range of E/P (pressure-reduced electric field) values. Several gas mixtures are provided that provide faster response in gas-filled detectors for convenient E/P ranges as compared with conventional gas mixtures.

Gas mixtures for gas-filled particle detectors

DOEpatents

Christophorou, Loucas G.; McCorkle, Dennis L.; Maxey, David V.; Carter, James G.

1980-01-01

Improved binary and tertiary gas mixtures for gas-filled particle detectors are provided. The components are chosen on the basis of the principle that the first component is one gas or mixture of two gases having a large electron scattering cross section at energies of about 0.5 eV and higher, and the second component is a gas (Ar) having a very small cross section at and below aout 0.5 eV, whereby fast electrons in the gaseous mixture are slowed into the energy range of about 0.5 eV where the cross section for the mixture is small and hence the electron mean free path is large. The reduction in both the cross section and the electron energy results in an increase in the drift velocity of the electrons in the gas mixtures over that for the separate components for a range of E/P (pressure-reduced electron field) values. Several gas mixtures are provided that provide faster response in gas-filled detectors for convenient E/P ranges as compared with conventional gas mixtures.

Improved gas mixtures for gas-filled radiation detectors

DOEpatents

Christophorou, L.G.; McCorkle, D.L.; Maxey, D.V.; Carter, J.G.

1980-03-28

Improved binary and ternary gas mixtures for gas-filled radiation detectors are provided. The components are chosen on the basis of the principle that the first component is one molecular gas or mixture of two molecular gases having a large electron scattering cross section at energies of about 0.5 eV and higher, and the second component is a noble gas having a very small cross section at and below about 1.0 eV, whereby fast electrons in the gaseous mixture are slowed into the energy range of about 0.5 eV where the cross section for the mixture is small and hence the electron mean free path is large. The reduction in both the cross section and the electron energy results in an increase in the drift velocity of the electrons in the gas mixtures over that for the separate components for a range of E/P (pressure-reduced electric field) values. Several gas mixtures are provided that provide faster response in gas-filled detectors for convenient E/P ranges as compared with conventional gas mixtures.

Improved gas mixtures for gas-filled particle detectors

DOEpatents

Christophorou, L.G.; McCorkle, D.L.; Maxey, D.V.; Carter, J.G.

Improved binary and tertiary gas mixture for gas-filled particle detectors are provided. The components are chosen on the basis of the principle that the first component is one gas or mixture of two gases having a large electron scattering cross section at energies of about 0.5 eV and higher, and the second component is a gas (Ar) having a very small cross section at and below about 0.5 eV; whereby fast electrons in the gaseous mixture are slowed into the energy range of about 0.5 eV where the cross section for the mixture is small and hence the electron mean free path is large. The reduction in both the cross section and the electron energy results in an increase in the drift velocity of the electrons in the gas mixtures over that for the separate components for a range of E/P (pressure-reduced electron field) values. Several gas mixtures are provided that provide faster response in gas-filled detectors for convenient E/P ranges as compared with conventional gas mixtures.

The magnetic polarity stratigraphy of the Mauch Chunk Formation, Pennsylvania

PubMed Central

Opdyke, Neil D.; DiVenere, Victor J.

2004-01-01

Three sections of Chesterian Mauch Chunk Formation in Pennsylvania have been studied paleomagnetically to determine a Late Mississippian magnetic polarity stratigraphy. The upper section at Lavelle includes a conglomerate with abundant red siltstone rip-up clasts that yielded a positive conglomerate test. All samples were subjected to progressive thermal demagnetization to temperatures as high as 700°C. Two components of magnetization were isolated: a synfolding “B” component and the prefolding “C” component. The conglomerate test is positive, indicating that the C component was acquired very early in the history of the sediment. A coherent pattern of magnetic polarity reversals was identified. Five magnetozones were identified in the upper Lavelle section, which yields a pattern that is an excellent match with the pattern of reversals obtained from the upper Mauch Chunk at the original type section of the Mississippian/Pennsylvanian boundary at Pottsville, PA. The frequency of reversals in the upper Mississippian, as identified in the Mauch Chunk Formation, is approximately one to two per million years, which is an average for field reversal through time. PMID:15353597

The magnetic polarity stratigraphy of the Mauch Chunk Formation, Pennsylvania.

PubMed

Opdyke, Neil D; DiVenere, Victor J

2004-09-14

Three sections of Chesterian Mauch Chunk Formation in Pennsylvania have been studied paleomagnetically to determine a Late Mississippian magnetic polarity stratigraphy. The upper section at Lavelle includes a conglomerate with abundant red siltstone rip-up clasts that yielded a positive conglomerate test. All samples were subjected to progressive thermal demagnetization to temperatures as high as 700 degrees C. Two components of magnetization were isolated: a synfolding "B" component and the prefolding "C" component. The conglomerate test is positive, indicating that the C component was acquired very early in the history of the sediment. A coherent pattern of magnetic polarity reversals was identified. Five magnetozones were identified in the upper Lavelle section, which yields a pattern that is an excellent match with the pattern of reversals obtained from the upper Mauch Chunk at the original type section of the Mississippian/Pennsylvanian boundary at Pottsville, PA. The frequency of reversals in the upper Mississippian, as identified in the Mauch Chunk Formation, is approximately one to two per million years, which is an average for field reversal through time.

Fragmentation cross sections of O-16 between 0.9 and 200 GeV/nucleon

NASA Technical Reports Server (NTRS)

Hirzebruch, S. E.; Heinrich, W.; Tolstov, K. D.; Kovalenko, A. D.; Benton, E. V.

1995-01-01

Inclusive cross sections for high energy interactions at 0.9, 2.3, 3.6, and 13.5 GeV/nucleon of O-16 with C, CR-39 (C12H18O7), CH2, Al, Cu, Ag, and Pb targets were measured. The total charge-changing cross sections and partial charge-changing cross sections for the production of fragments with charge Z = 6 and Z = 7 are compared to previous experiments at 60 and 200 GeV/nucleon. The contributions of Coulomb dissociation to the total cross sections are calculated. Using factorization rules the partial electromagnetic cross sections are separated from the nuclear components. Energy dependence of both components are investigated and discussed.

Femtosecond Fiber Lasers Based on Dissipative Processes for Nonlinear Microscopy

PubMed Central

Wise, Frank W.

2012-01-01

Recent progress in the development of femtosecond-pulse fiber lasers with parameters appropriate for nonlinear microscopy is reviewed. Pulse-shaping in lasers with only normal-dispersion components is briefly described, and the performance of the resulting lasers is summarized. Fiber lasers based on the formation of dissipative solitons now offer performance competitive with that of solid-state lasers, but with the benefits of the fiber medium. Lasers based on self-similar pulse evolution in the gain section of a laser also offer a combination of short pulse duration and high pulse energy that will be attractive for applications in nonlinear bioimaging. PMID:23869163

Are sectioning and soldering of short-span implant-supported prostheses necessary procedures?

PubMed

Bianchini, Marco A; Souza, João G O; Souza, Dircilene C; Magini, Ricardo S; Benfatti, Cesar A M; Cardoso, Antonio C

2011-01-01

The aim of this study was to evaluate the fit between dental abutments and the metal framework of a 3-unit fixed prosthesis screwed to two implants to determine whether sectioning and soldering of the framework are in fact necessary procedures. The study was based on a model of a metal framework of a 3-unit prosthesis screwed to two implants. A total of 18 metal frameworks were constructed and divided into 3 groups: (1) NS group - each framework was cast in one piece and not sectioned; (2) CS group - the components of each sectioned framework were joined by conventional soldering; and (3) LW group - the components of each sectioned framework were joined by laser welding. The control group consisted of six silver-palladium alloy copings that were not cast together. Two analyses were mperformed: in the first analysis, the framework was screwed only to the first abutment, and in the second analysis, the framework was screwed to both abutments. The prosthetic fit was assessed at a single point using a measuring microscope (Measurescope, Nikon, Japan) and the marginal gap was measured in micrometers. Statistical analysis was performed using analysis of variance (ANOVA), Scheffe's test, Student's t-test, and Mann-Whitney U test. The NS group had larger marginal gaps than the other groups (p<0.01), while the CS and LW groups had a similar degree of misfit with no significant difference between them. The results revealed that, in the case of short-span 3-unit fixed prostheses, the framework should be sectioned and soldered or welded to prevent or reduce marginal gaps between the metal framework and dental abutments.

Feature Extraction for Track Section Status Classification Based on UGW Signals

PubMed Central

Yang, Yuan; Shi, Lin

2018-01-01

Track status classification is essential for the stability and safety of railway operations nowadays, when railway networks are becoming more and more complex and broad. In this situation, monitoring systems are already a key element in applications dedicated to evaluating the status of a certain track section, often determining whether it is free or occupied by a train. Different technologies have already been involved in the design of monitoring systems, including ultrasonic guided waves (UGW). This work proposes the use of the UGW signals captured by a track monitoring system to extract the features that are relevant for determining the corresponding track section status. For that purpose, three features of UGW signals have been considered: the root mean square value, the energy, and the main frequency components. Experimental results successfully validated how these features can be used to classify the track section status into free, occupied and broken. Furthermore, spatial and temporal dependencies among these features were analysed in order to show how they can improve the final classification performance. Finally, a preliminary high-level classification system based on deep learning networks has been envisaged for future works. PMID:29673156

Preassembled Building Components. Proceedings of a Program Conducted as Part of the Conferences of the Building Research Institute Division of Engineering and Industrial Research (Fall 1960).

ERIC Educational Resources Information Center

National Academy of Sciences - National Research Council, Washington, DC.

Four aspects of preassembled building components are discussed--(1) attitudes on preassembled components, (2) principles of preassembled components construction, (3) structural component case studies, and (4) mechanical component case studies. In section 1, various views on preassembled components are discussed including--(1) the architect's view,…

Nurses’ knowledge of blood transfusion in medical training centers of Shahrekord University of Medical Science in 2004

PubMed Central

Aslani, Yosef; Etemadyfar, Shahram; Noryan, Kobra

2010-01-01

BACKGROUND: Using blood and blood components is a common therapeutic procedure in hospitals. Nurses have an important role in a safe blood transfusion. Therefore, it is crucial for nurses to have sufficient knowledge of situations, amount and methods of using blood components, possible side effects and necessary cares. This study investigated nurses’ knowledge of blood transfusion. METHODS: This was a cross-sectional descriptive study on 117 nurses in medical training hospitals of Shahrekord University of Medical Sciences in 2004, aiming to evaluate their knowledge of blood transfusion. Data were collected using a questionnaire including 4 sections and 29 questions. Sections included demographic data, nurses’ knowledge of blood components, nurses’ knowledge of blood components infusion techniques, and nurses’ knowledge of indication and side effects of blood components infusion. Knowledge scores were first coded and then categorized in three levels of good, average, and poor. Data were analyzed using SPSS software. RESULTS: The nurses’ knowledge of blood and blood component, techniques of blood components infusion, and its indication and side effects was average (66.7%, 65.8% and 59%, respectively). CONCLUSIONS: The findings showed that the nurses’ knowledge of blood and blood component was average and insufficient. Therefore, it is recommended to activate the blood transfusion committees in hospitals to increase the quality of this common procedure and prevent side effects by in-service trainings of nurses. PMID:21589778

Quantitative allochem compositional analysis of Lochkovian-Pragian boundary sections in the Prague Basin (Czech Republic)

NASA Astrophysics Data System (ADS)

Weinerová, Hedvika; Hron, Karel; Bábek, Ondřej; Šimíček, Daniel; Hladil, Jindřich

2017-06-01

Quantitative allochem compositional trends across the Lochkovian-Pragian boundary Event were examined at three sections recording the proximal to more distal carbonate ramp environment of the Prague Basin. Multivariate statistical methods (principal component analysis, correspondence analysis, cluster analysis) of point-counted thin section data were used to reconstruct facies stacking patterns and sea-level history. Both the closed-nature allochem percentages and their centred log-ratio (clr) coordinates were used. Both these approaches allow for distinguishing of lowstand, transgressive and highstand system tracts within the Praha Formation, which show gradual transition from crinoid-dominated facies deposited above the storm wave base to dacryoconarid-dominated facies of deep-water environment below the storm wave base. Quantitative compositional data also indicate progradative-retrogradative trends in the macrolithologically monotonous shallow-water succession and enable its stratigraphic correlation with successions from deeper-water environments. Generally, the stratigraphic trends of the clr data are more sensitive to subtle changes in allochem composition in comparison to the results based on raw data. A heterozoan-dominated allochem association in shallow-water environments of the Praha Formation supports the carbonate ramp environment assumed by previous authors.

Reliability Assessment Approach for Stirling Convertors and Generators

NASA Technical Reports Server (NTRS)

Shah, Ashwin R.; Schreiber, Jeffrey G.; Zampino, Edward; Best, Timothy

2004-01-01

Stirling power conversion is being considered for use in a Radioisotope Power System for deep-space science missions because it offers a multifold increase in the conversion efficiency of heat to electric power. Quantifying the reliability of a Radioisotope Power System that utilizes Stirling power conversion technology is important in developing and demonstrating the capability for long-term success. A description of the Stirling power convertor is provided, along with a discussion about some of the key components. Ongoing efforts to understand component life, design variables at the component and system levels, related sources, and the nature of uncertainties is discussed. The requirement for reliability also is discussed, and some of the critical areas of concern are identified. A section on the objectives of the performance model development and a computation of reliability is included to highlight the goals of this effort. Also, a viable physics-based reliability plan to model the design-level variable uncertainties at the component and system levels is outlined, and potential benefits are elucidated. The plan involves the interaction of different disciplines, maintaining the physical and probabilistic correlations at all the levels, and a verification process based on rational short-term tests. In addition, both top-down and bottom-up coherency were maintained to follow the physics-based design process and mission requirements. The outlined reliability assessment approach provides guidelines to improve the design and identifies governing variables to achieve high reliability in the Stirling Radioisotope Generator design.

High-heat-flux testing of irradiated tungsten-based materials for fusion applications using infrared plasma arc lamps

DOE PAGES

Sabau, Adrian S.; Ohriner, Evan K.; Kiggans, Jim; ...

2014-11-01

Testing of advanced materials and component mock-ups under prototypical fusion high-heat-flux conditions, while historically a mainstay of fusion research, has proved to be quite challenging, especially for irradiated materials. A new high-heat-flux–testing (HHFT) facility based on water-wall plasma arc lamps (PALs) is now introduced for materials and small-component testing. Two PAL systems, utilizing a 12 000°C plasma arc contained in a quartz tube cooled by a spiral water flow over the inside tube surface, provide maximum incident heat fluxes of 4.2 and 27 MW/m 2 over areas of 9×12 and 1×10 cm 2, respectively. This paper will present the overallmore » design and implementation of a PAL-based irradiated material target station (IMTS). The IMTS is primarily designed for testing the effects of heat flux or thermal cycling on material coupons of interest, such as those for plasma-facing components. Temperature results are shown for thermal cycling under HHFT of tungsten coupon specimens that were neutron irradiated in HFIR. Finally, radiological surveys indicated minimal contamination of the 36×36×18 cm test section, demonstrating the capability of the new facility to handle irradiated specimens at high temperature.« less

Ceramic Composite Development for Gas Turbine Engine Hot Section Components

NASA Technical Reports Server (NTRS)

DiCarlo, James A.; VANrOODE, mARK

2006-01-01

The development of ceramic materials for incorporation into the hot section of gas turbine engines has been ongoing for about fifty years. Researchers have designed, developed, and tested ceramic gas turbine components in rigs and engines for automotive, aero-propulsion, industrial, and utility power applications. Today, primarily because of materials limitations and/or economic factors, major challenges still remain for the implementation of ceramic components in gas turbines. For example, because of low fracture toughness, monolithic ceramics continue to suffer from the risk of failure due to unknown extrinsic damage events during engine service. On the other hand, ceramic matrix composites (CMC) with their ability to display much higher damage tolerance appear to be the materials of choice for current and future engine components. The objective of this paper is to briefly review the design and property status of CMC materials for implementation within the combustor and turbine sections for gas turbine engine applications. It is shown that although CMC systems have advanced significantly in thermo-structural performance within recent years, certain challenges still exist in terms of producibility, design, and affordability for commercial CMC turbine components. Nevertheless, there exist some recent successful efforts for prototype CMC components within different engine types.

Impact Testing and Simulation of Composite Airframe Structures

NASA Technical Reports Server (NTRS)

Jackson, Karen E.; Littell, Justin D.; Horta, Lucas G.; Annett, Martin S.; Fasanella, Edwin L.; Seal, Michael D., II

2014-01-01

Dynamic tests were performed at NASA Langley Research Center on composite airframe structural components of increasing complexity to evaluate their energy absorption behavior when subjected to impact loading. A second objective was to assess the capabilities of predicting the dynamic response of composite airframe structures, including damage initiation and progression, using a state-of-the-art nonlinear, explicit transient dynamic finite element code, LS-DYNA. The test specimens were extracted from a previously tested composite prototype fuselage section developed and manufactured by Sikorsky Aircraft Corporation under the US Army's Survivable Affordable Repairable Airframe Program (SARAP). Laminate characterization testing was conducted in tension and compression. In addition, dynamic impact tests were performed on several components, including I-beams, T-sections, and cruciform sections. Finally, tests were conducted on two full-scale components including a subfloor section and a framed fuselage section. These tests included a modal vibration and longitudinal impact test of the subfloor section and a quasi-static, modal vibration, and vertical drop test of the framed fuselage section. Most of the test articles were manufactured of graphite unidirectional tape composite with a thermoplastic resin system. However, the framed fuselage section was constructed primarily of a plain weave graphite fabric material with a thermoset resin system. Test data were collected from instrumentation such as accelerometers and strain gages and from full-field photogrammetry.

Progress Report on Alloy 617 Notched Specimen Testing

DOE Office of Scientific and Technical Information (OSTI.GOV)

McMurtrey, Michael David; Wright, Richard Neil; Lillo, Thomas Martin

Creep behavior of Alloy 617 has been extensively characterized to support the development of a draft Code Case to qualify Alloy 617 in Section III division 5 of the ASME Boiler and Pressure Vessel Code. This will allow use of Alloy 617 in construction of nuclear reactor components at elevated temperatures and longer periods of time (up to 950°C and 100,000 hours). Prior to actual use, additional concerns not considered in the ASME code need to be addressed. Code Cases are based largely on uniaxial testing of smooth gage specimens. In service conditions, components will generally be under multi axialmore » loading. There is also the concern of the behavior at discontinuities, such as threaded components. To address the concerns of multi axial creep behavior and at geometric discontinuities, notched specimens have been designed to create conditions representative of the states that service components experience. Two general notch geometries have been used for these series of tests: U notch and V notch specimens. The notches produce a tri axial stress state, though not uniform across the specimen. Characterization of the creep behavior of the U notch specimens and the creep rupture behavior of the V notch specimens provides a good approximation of the behavior expected of actual components. Preliminary testing and analysis have been completed and are reported in this document. This includes results from V notch specimens tested at 900°C and 800°C. Failure occurred in the smooth gage section of the specimen rather than at the root of the notch, though some damage was present at the root of the notch, where initial stress was highest. This indicates notch strengthening behavior in this material at these temperatures.« less

76 FR 55416 - In the Matter of Certain Led Photographic Lighting Devices and Components Thereof; Notice of...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-07

...Notice is hereby given that a complaint was filed with the U.S. International Trade Commission on August 3, 2011, under section 337 of the Tariff Act of 1930, as amended, 19 U.S.C. 1337, on behalf of Litepanels, Ltd. of the United Kingdom and Litepanels, Inc. of Van Nuys, California. Supplements to the Complaint were filed on August 24, and August 25, 2011. The complaint alleges violations of section 337 based upon the importation into the United States, the sale for importation, and the sale within the United States after importation of certain LED photographic lighting devices and components thereof by reason of infringement of certain claims of U.S. Patent No. 7,972,022 (``the `022 patent''); U.S. Patent No. 7,510,290 (``the `290 patent''); U.S. Patent No. 7,429,117 (``the `117 patent''); U.S. Patent No. 7,318,652 (``the `652 patent''); and U.S. Patent No. 6,948,823 (``the `823 patent''). The complaint further alleges that an industry in the United States exists as required by subsection (a)(2) of section 337. The complainants request that the Commission institute an investigation and, after the investigation, issue an exclusion order and cease and desist orders.

Direct measurements of the optical cross sections and refractive indices of individual volatile and hygroscopic aerosol particles.

PubMed

Mason, B J; Cotterell, M I; Preston, T C; Orr-Ewing, A J; Reid, J P

2015-06-04

We present measurements of the evolving extinction cross sections of individual aerosol particles (spanning 700-2500 nm in radius) during the evaporation of volatile components or hygroscopic growth using a combination of a single particle trap formed from a Bessel light beam and cavity ring-down spectroscopy. For single component organic aerosol droplets of 1,2,6-hexanetriol, polyethylene glycol 400, and glycerol, the slow evaporation of the organic component (over time scales of 1000 to 10,000 s) leads to a time-varying size and extinction cross section that can be used to estimate the refractive index of the droplet. Measurements on binary aqueous-inorganic aerosol droplets containing one of the inorganic solutes ammonium bisulfate, ammonium sulfate, sodium nitrate, or sodium chloride (over time scales of 1000 to 15,000 s) under conditions of changing relative humidity show that extinction cross-section measurements are consistent with expectations from accepted models for the variation in droplet refractive index with hygroscopic growth. In addition, we use these systems to establish an experimental protocol for future single particle extinction measurements. The advantages of mapping out the evolving light extinction cross-section of an individual particle over extended time frames accompanied by hygroscopic cycling or component evaporation are discussed.

Using satellite observations to quantify biomass burning emissions of NOx, and hydrocarbons in the Tropics

NASA Technical Reports Server (NTRS)

Jaegle, Lyatt

2005-01-01

This is the final report for "Using satellite observations to quantify biomass burning emissions of NOx and hydrocarbons in the Tropics", funded through the New Investigator Program between March 2001 and March 2005. This period includes a 1-year no-cost extension of the original award. This report summarizes our accomplishments during the duration of the grant. Section 2 focuses on the research component of this work, while section 3 describes the education component. The personnel supported under this project is given in section 4. Section 5 lists publications resulting from NASA support and section 6 provides a list of conferences and seminars where the results were presented.

26 CFR 1.23-5 - Certification procedures.

Code of Federal Regulations, 2013 CFR

2013-04-01

... definition of an energy-conserving component or renewable energy source property. Upon the request of a...)(1)). (2) The item meets the definition of an other energy-conserving component specified in section 23(c)(4) or former section 44C(c)(4) see (§ 1.23-2(d)(4)). (3) The item meets the definition of solar...

26 CFR 1.23-5 - Certification procedures.

Code of Federal Regulations, 2012 CFR

2012-04-01

... definition of an energy-conserving component or renewable energy source property. Upon the request of a...)(1)). (2) The item meets the definition of an other energy-conserving component specified in section 23(c)(4) or former section 44C(c)(4) see (§ 1.23-2(d)(4)). (3) The item meets the definition of solar...

26 CFR 1.23-5 - Certification procedures.

Code of Federal Regulations, 2014 CFR

2014-04-01

... definition of an energy-conserving component or renewable energy source property. Upon the request of a...)(1)). (2) The item meets the definition of an other energy-conserving component specified in section 23(c)(4) or former section 44C(c)(4) see (§ 1.23-2(d)(4)). (3) The item meets the definition of solar...

21 CFR 177.1635 - Poly(p-methylstyrene) and rubber-modified poly(p-methyl-styrene).

Code of Federal Regulations, 2010 CFR

2010-04-01

...-modified poly(p-methylstyrene) identified in this section may be safely used as components of articles... are available from the Center for Food Safety and Applied Nutrition (HFS-200), Food and Drug... complying with this section, when used as components of the food-contact surface of any article that is the...

Raman imaging to investigate ultrastructure and composition of plant cell walls : distribution of lignin and cellulose in black spruce wood (Picea mariana)

Treesearch

Umesh P. Agarwal

2006-01-01

A detailed understanding of the structural organization of the cell wall of vascular plants is important from both the perspectives of plant biology and chemistry and of commercial utilization. A state-of-the-art 633-nm laser-based confocal Raman microscope was used to determine the distribution of cell wall components in the cross section of black spruce wood in situ...

42 CFR 93.209 - Funding component.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 42 Public Health 1 2014-10-01 2014-10-01 false Funding component. 93.209 Section 93.209 Public... EFFECTS STUDIES OF HAZARDOUS SUBSTANCES RELEASES AND FACILITIES PUBLIC HEALTH SERVICE POLICIES ON RESEARCH MISCONDUCT Definitions § 93.209 Funding component. Funding component means any organizational unit of the PHS...

42 CFR 93.209 - Funding component.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 42 Public Health 1 2012-10-01 2012-10-01 false Funding component. 93.209 Section 93.209 Public... EFFECTS STUDIES OF HAZARDOUS SUBSTANCES RELEASES AND FACILITIES PUBLIC HEALTH SERVICE POLICIES ON RESEARCH MISCONDUCT Definitions § 93.209 Funding component. Funding component means any organizational unit of the PHS...

42 CFR 93.209 - Funding component.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 42 Public Health 1 2013-10-01 2013-10-01 false Funding component. 93.209 Section 93.209 Public... EFFECTS STUDIES OF HAZARDOUS SUBSTANCES RELEASES AND FACILITIES PUBLIC HEALTH SERVICE POLICIES ON RESEARCH MISCONDUCT Definitions § 93.209 Funding component. Funding component means any organizational unit of the PHS...

42 CFR 93.209 - Funding component.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 42 Public Health 1 2011-10-01 2011-10-01 false Funding component. 93.209 Section 93.209 Public... EFFECTS STUDIES OF HAZARDOUS SUBSTANCES RELEASES AND FACILITIES PUBLIC HEALTH SERVICE POLICIES ON RESEARCH MISCONDUCT Definitions § 93.209 Funding component. Funding component means any organizational unit of the PHS...

42 CFR 93.209 - Funding component.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 42 Public Health 1 2010-10-01 2010-10-01 false Funding component. 93.209 Section 93.209 Public... EFFECTS STUDIES OF HAZARDOUS SUBSTANCES RELEASES AND FACILITIES PUBLIC HEALTH SERVICE POLICIES ON RESEARCH MISCONDUCT Definitions § 93.209 Funding component. Funding component means any organizational unit of the PHS...

46 CFR 160.076-21 - Component materials.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 6 2011-10-01 2011-10-01 false Component materials. 160.076-21 Section 160.076-21 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS... Component materials. (a) Each component material used in the manufacturer of an inflatable PFD must— (1...

46 CFR 160.076-21 - Component materials.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 6 2013-10-01 2013-10-01 false Component materials. 160.076-21 Section 160.076-21 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS... Component materials. Each component material used in the manufacture of an inflatable PFD must— (a) Meet the...

46 CFR 160.076-21 - Component materials.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 6 2014-10-01 2014-10-01 false Component materials. 160.076-21 Section 160.076-21 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS... Component materials. Each component material used in the manufacture of an inflatable PFD must— (a) Meet the...

14 CFR 25.1711 - Component identification: EWIS.

Code of Federal Regulations, 2010 CFR

2010-01-01

... rules, by operating rules, or as a result of the assessment required by § 25.1709, EWIS components...) of this section must remain legible throughout the expected service life of the EWIS component. (d... adverse effect on the performance of that component throughout its expected service life. (e...

49 CFR 195.254 - Above ground components.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 3 2010-10-01 2010-10-01 false Above ground components. 195.254 Section 195.254 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY... PIPELINE Construction § 195.254 Above ground components. (a) Any component may be installed above ground in...

49 CFR 195.254 - Above ground components.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 3 2011-10-01 2011-10-01 false Above ground components. 195.254 Section 195.254 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY... PIPELINE Construction § 195.254 Above ground components. (a) Any component may be installed above ground in...

Angular analysis of the e + e - → D ( * ) ± D * ∓ process near the open charm threshold using initial-state radiation

DOE PAGES

Zhukova, V.

2018-01-10

Here, we repormore » t a new measurement of the exclusive e + e - → D ( * ) ± D * ∓ cross sections as a function of the center-of-mass energy from the D ( * ) ± D * ∓ threshold through $$ \\sqrt{s}=6.0 $$ GeV, using the initial-state radiation technique. The analysis is based on a data sample collected with the Belle detector with an integrated luminosity of 951 fb -1. The accuracy of the cross section measurement is increased by a factor of 2 over the first Belle study. We perform the first angular analysis of the e + e - → D ( * ) ± D * ∓ process and decompose this exclusive cross section into three components corresponding to the D * helicities.« less

Angular analysis of the e + e - → D ( * ) ± D * ∓ process near the open charm threshold using initial-state radiation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhukova, V.

Here, we repormore » t a new measurement of the exclusive e + e - → D ( * ) ± D * ∓ cross sections as a function of the center-of-mass energy from the D ( * ) ± D * ∓ threshold through $$ \\sqrt{s}=6.0 $$ GeV, using the initial-state radiation technique. The analysis is based on a data sample collected with the Belle detector with an integrated luminosity of 951 fb -1. The accuracy of the cross section measurement is increased by a factor of 2 over the first Belle study. We perform the first angular analysis of the e + e - → D ( * ) ± D * ∓ process and decompose this exclusive cross section into three components corresponding to the D * helicities.« less

Biochronostratigraphy and paleoenvironment analysis of Neogene deposits from the Pelotas Basin (well 2-TG-96-RS), Southernmost Brazil.

PubMed

Silva, Wagner G; Zerfass, Geise S A; Souza, Paulo A; Helenes, Javier

2015-09-01

This paper presents the integration of micropaleontological (palynology and foraminifera) and isotopic (87Sr/86Sr) analysis of a selected interval from the well 2-TG-96-RS, drilled on the onshore portion of the Pelotas Basin, Rio Grande do Sul, Brazil. A total of eight samples of the section between 140.20 and 73.50 m in depth was selected for palynological analysis, revealing diversified and abundant palynomorph associations. Species of spores, pollen grains and dinoflagellate cysts are the most common palynomorphs found. Planktic and benthic calcareous foraminifera were recovered from the lowest two levels of the section (140.20 and 134.30 m). Based on the stratigraphic range of the species of dinoflagellate cysts and sporomorphs, a span age from Late Miocene to Early Pliocene is assigned. The relative age obtained from the 87Sr/86Sr ratio in shells of calcareous foraminifers indicates a Late Miocene (Messinian) correspondence, corroborating the biostratigraphic positioning performed with palynomorphs. Paleoenvironmental interpretations based on the quantitative distribution of organic components (palynomorphs, phytoclasts and amorphous organic matter) throughout the section and on foraminiferal associations indicate a shallow marine depositional environment for the section. Two palynologicals intervals were recognized based on palynofacies analysis, related to middle to outer shelf (140.20 to 128.90 m) and inner shelf (115.75 to 73.50 m) conditions.

21 CFR 3.4 - Designated agency component.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 1 2013-04-01 2013-04-01 false Designated agency component. 3.4 Section 3.4 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES GENERAL PRODUCT JURISDICTION Assignment of Agency Component for Review of Premarket Applications § 3.4 Designated agency component. (a) To designate the agency component...

21 CFR 3.4 - Designated agency component.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 1 2010-04-01 2010-04-01 false Designated agency component. 3.4 Section 3.4 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES GENERAL PRODUCT JURISDICTION Assignment of Agency Component for Review of Premarket Applications § 3.4 Designated agency component. (a) To designate the agency component...

21 CFR 3.4 - Designated agency component.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 1 2011-04-01 2011-04-01 false Designated agency component. 3.4 Section 3.4 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES GENERAL PRODUCT JURISDICTION Assignment of Agency Component for Review of Premarket Applications § 3.4 Designated agency component. (a) To designate the agency component...

21 CFR 3.4 - Designated agency component.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 1 2014-04-01 2014-04-01 false Designated agency component. 3.4 Section 3.4 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES GENERAL PRODUCT JURISDICTION Assignment of Agency Component for Review of Premarket Applications § 3.4 Designated agency component. (a) To designate the agency component...

First Measurement of the Muon Anti-Neutrino Charged Current Quasielastic Double-Differential Cross-Section

DOE Office of Scientific and Technical Information (OSTI.GOV)

Grange, Joseph M.

2013-01-01

This dissertation presents the first measurement of the muon antineutrino charged current quasi-elastic double-differential cross section. These data significantly extend the knowledge of neutrino and antineutrino interactions in the GeV range, a region that has recently come under scrutiny due to a number of conflicting experimental results. To maximize the precision of this measurement, three novel techniques were employed to measure the neutrino background component of the data set. Representing the first measurements of the neutrino contribution to an accelerator-based antineutrino beam in the absence of a magnetic field, the successful execution of these techniques carry implications for current andmore » future neutrino experiments.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hamilton, Bruce Duncan

The objective of the report is to provide an assessment of the domestic supply chain and manufacturing infrastructure supporting the U.S. offshore wind market. The report provides baseline information and develops a strategy for future development of the supply chain required to support projected offshore wind deployment levels. A brief description of each of the key chapters includes: » Chapter 1: Offshore Wind Plant Costs and Anticipated Technology Advancements. Determines the cost breakdown of offshore wind plants and identifies technical trends and anticipated advancements in offshore wind manufacturing and construction. » Chapter 2: Potential Supply Chain Requirements and Opportunities. Providesmore » an organized, analytical approach to identifying and bounding the uncertainties associated with a future U.S. offshore wind market. It projects potential component-level supply chain needs under three demand scenarios and identifies key supply chain challenges and opportunities facing the future U.S. market as well as current suppliers of the nation’s land-based wind market. » Chapter 3: Strategy for Future Development. Evaluates the gap or competitive advantage of adding manufacturing capacity in the U.S. vs. overseas, and evaluates examples of policies that have been successful . » Chapter 4: Pathways for Market Entry. Identifies technical and business pathways for market entry by potential suppliers of large-scale offshore turbine components and technical services. The report is intended for use by the following industry stakeholder groups: (a) Industry participants who seek baseline cost and supplier information for key component segments and the overall U.S. offshore wind market (Chapters 1 and 2). The component-level requirements and opportunities presented in Section 2.3 will be particularly useful in identifying market sizes, competition, and risks for the various component segments. (b) Federal, state, and local policymakers and economic development agencies, to assist in identifying policies with low effort and high impact (Chapter 3). Section 3.3 provides specific policy examples that have been demonstrated to be effective in removing barriers to development. (c) Current and potential domestic suppliers in the offshore wind market, in evaluating areas of opportunity and understanding requirements for participation (Chapter 4). Section 4.4 provides a step-by-step description of the qualification process that suppliers looking to sell components into a future U.S. offshore wind market will need to follow.« less

Voltage Based Detection Method for High Impedance Fault in a Distribution System

NASA Astrophysics Data System (ADS)

Thomas, Mini Shaji; Bhaskar, Namrata; Prakash, Anupama

2016-09-01

High-impedance faults (HIFs) on distribution feeders cannot be detected by conventional protection schemes, as HIFs are characterized by their low fault current level and waveform distortion due to the nonlinearity of the ground return path. This paper proposes a method to identify the HIFs in distribution system and isolate the faulty section, to reduce downtime. This method is based on voltage measurements along the distribution feeder and utilizes the sequence components of the voltages. Three models of high impedance faults have been considered and source side and load side breaking of the conductor have been studied in this work to capture a wide range of scenarios. The effect of neutral grounding of the source side transformer is also accounted in this study. The results show that the algorithm detects the HIFs accurately and rapidly. Thus, the faulty section can be isolated and service can be restored to the rest of the consumers.

Modification of the Douglas Neumann program to improve the efficiency of predicting component interference and high lift characteristics

NASA Technical Reports Server (NTRS)

Bristow, D. R.; Grose, G. G.

1978-01-01

The Douglas Neumann method for low-speed potential flow on arbitrary three-dimensional lifting bodies was modified by substituting the combined source and doublet surface paneling based on Green's identity for the original source panels. Numerical studies show improved accuracy and stability for thin lifting surfaces, permitting reduced panel number for high-lift devices and supercritical airfoil sections. The accuracy of flow in concave corners is improved. A method of airfoil section design for a given pressure distribution, based on Green's identity, was demonstrated. The program uses panels on the body surface with constant source strength and parabolic distribution of doublet strength, and a doublet sheet on the wake. The program is written for the CDC CYBER 175 computer. Results of calculations are presented for isolated bodies, wings, wing-body combinations, and internal flow.

A review of European applications of artificial intelligence to space

NASA Technical Reports Server (NTRS)

Drummond, Mark (Editor); Stewart, Helen (Editor)

1993-01-01

The purpose is to describe the applications of Artificial Intelligence (AI) to the European Space program that are being developed or have been developed. The results of a study sponsored by the Artificial Intelligence Research and Development program of NASA's Office of Advanced Concepts and Technology (OACT) are described. The report is divided into two sections. The first consists of site reports, which are descriptions of the AI applications seen at each place visited. The second section consists of two summaries which synthesize the information in the site reports by organizing this information in two different ways. The first organizes the material in terms of the type of application, e.g., data analysis, planning and scheduling, and procedure management. The second organizes the material in terms of the component technologies of Artificial Intelligence which the applications used, e.g., knowledge based systems, model based reasoning, procedural reasoning, etc.

How the Klein–Nishina formula was derived: Based on the Sangokan Nishina Source Materials

PubMed Central

YAZAKI, Yuji

2017-01-01

In 1928, Klein and Nishina investigated Compton scattering based on the Dirac equation just proposed in the same year, and derived the Klein–Nishina formula for the scattering cross section of a photon. At that time the Dirac equation had the following unsettled conceptual questions: the negative energy states, its four-component wave functions, and the spin states of an electron. Hence, during their investigation struggles, they encountered various difficulties. In this article, we describe their struggles to derive the formula using the “Sangokan Nishina Source Materials” retained in the the Nishina Memorial Foundation. PMID:28603211

Simple refractometer based on in-line fiber interferometers

NASA Astrophysics Data System (ADS)

Esteban, Ó.; Martínez Manuel, R.; Shlyagin, M. G.

2015-09-01

A very simple but accurate optical fiber refractometer based on the Fresnel reflection in the fiber tip and two in-line low-reflective mirrors for light intensity referencing is reported. Each mirror was generated by connecting together 2 fiber sections with FC/PC and FC/APC connectors using the standard FC/PC mating sleeve. For the sensor interrogation, a standard DFB diode laser pumped with a sawtooth-wave current was used. A resolution of 6 x 10-4 was experimentally demonstrated using different liquids. A simple sensor construction and the use of low cost components make the reported system interesting for many applications.

19 CFR 10.183 - Duty-free entry of civil aircraft, aircraft engines, ground flight simulators, parts, components...

Code of Federal Regulations, 2014 CFR

2014-04-01

... engines, ground flight simulators, parts, components, and subassemblies. 10.183 Section 10.183 Customs... Duty-free entry of civil aircraft, aircraft engines, ground flight simulators, parts, components, and... aircraft, aircraft engines, and ground flight simulators, including their parts, components, and...

19 CFR 10.183 - Duty-free entry of civil aircraft, aircraft engines, ground flight simulators, parts, components...

Code of Federal Regulations, 2013 CFR

2013-04-01

... engines, ground flight simulators, parts, components, and subassemblies. 10.183 Section 10.183 Customs... Duty-free entry of civil aircraft, aircraft engines, ground flight simulators, parts, components, and... aircraft, aircraft engines, and ground flight simulators, including their parts, components, and...

19 CFR 10.183 - Duty-free entry of civil aircraft, aircraft engines, ground flight simulators, parts, components...

Code of Federal Regulations, 2012 CFR

2012-04-01

... engines, ground flight simulators, parts, components, and subassemblies. 10.183 Section 10.183 Customs... Duty-free entry of civil aircraft, aircraft engines, ground flight simulators, parts, components, and... aircraft, aircraft engines, and ground flight simulators, including their parts, components, and...

40 CFR 62.14505 - What are the principal components of this subpart?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 8 2010-07-01 2010-07-01 false What are the principal components of this subpart? 62.14505 Section 62.14505 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... components of this subpart? This subpart contains the eleven major components listed in paragraphs (a...

2 CFR 1125.937 - DoD Component.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 2 Grants and Agreements 1 2011-01-01 2011-01-01 false DoD Component. 1125.937 Section 1125.937 Grants and Agreements Federal Agency Regulations for Grants and Agreements DEPARTMENT OF DEFENSE NONPROCUREMENT DEBARMENT AND SUSPENSION Definitions § 1125.937 DoD Component. In this part, DoD Component means...

30 CFR 7.507 - Air-monitoring components.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Air-monitoring components. 7.507 Section 7.507... APPROVAL OF MINING PRODUCTS TESTING BY APPLICANT OR THIRD PARTY Refuge Alternatives § 7.507 Air-monitoring components. (a) Each refuge alternative shall have an air-monitoring component that provides persons inside...

30 CFR 7.507 - Air-monitoring components.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Air-monitoring components. 7.507 Section 7.507... APPROVAL OF MINING PRODUCTS TESTING BY APPLICANT OR THIRD PARTY Refuge Alternatives § 7.507 Air-monitoring components. (a) Each refuge alternative shall have an air-monitoring component that provides persons inside...

30 CFR 7.507 - Air-monitoring components.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Air-monitoring components. 7.507 Section 7.507... APPROVAL OF MINING PRODUCTS TESTING BY APPLICANT OR THIRD PARTY Refuge Alternatives § 7.507 Air-monitoring components. (a) Each refuge alternative shall have an air-monitoring component that provides persons inside...

30 CFR 27.22 - Methane detector component.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Methane detector component. 27.22 Section 27.22... APPROVAL OF MINING PRODUCTS METHANE-MONITORING SYSTEMS Construction and Design Requirements § 27.22 Methane detector component. (a) A methane detector component shall be suitably constructed for incorporation in or...

21 CFR 888.5940 - Cast component.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Cast component. 888.5940 Section 888.5940 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES ORTHOPEDIC DEVICES Surgical Devices § 888.5940 Cast component. (a) Identification. A cast component is a...

21 CFR 888.5940 - Cast component.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Cast component. 888.5940 Section 888.5940 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES ORTHOPEDIC DEVICES Surgical Devices § 888.5940 Cast component. (a) Identification. A cast component is a...

21 CFR 888.5940 - Cast component.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Cast component. 888.5940 Section 888.5940 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES ORTHOPEDIC DEVICES Surgical Devices § 888.5940 Cast component. (a) Identification. A cast component is a...

30 CFR 27.22 - Methane detector component.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Methane detector component. 27.22 Section 27.22... detector component. (a) A methane detector component shall be suitably constructed for incorporation in or... detector shall include: (1) A method of continuous sampling of the atmosphere in which it functions. (2) A...

30 CFR 27.22 - Methane detector component.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Methane detector component. 27.22 Section 27.22... detector component. (a) A methane detector component shall be suitably constructed for incorporation in or... detector shall include: (1) A method of continuous sampling of the atmosphere in which it functions. (2) A...

30 CFR 27.22 - Methane detector component.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Methane detector component. 27.22 Section 27.22... detector component. (a) A methane detector component shall be suitably constructed for incorporation in or... detector shall include: (1) A method of continuous sampling of the atmosphere in which it functions. (2) A...

30 CFR 27.22 - Methane detector component.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Methane detector component. 27.22 Section 27.22... detector component. (a) A methane detector component shall be suitably constructed for incorporation in or... detector shall include: (1) A method of continuous sampling of the atmosphere in which it functions. (2) A...

NASA Tech Briefs, July 2001. Volume 25, No. 7

NASA Technical Reports Server (NTRS)

2001-01-01

Topics include: special coverage sections on Data Acquisition, and sections on electronic components and systems, software, mechanics, machinery/automation, biomedical and a special section of Photonics Tech Briefs.

The development and exploratory analysis of the Back Pain Attitudes Questionnaire (Back-PAQ)

PubMed Central

Darlow, Ben; Perry, Meredith; Mathieson, Fiona; Stanley, James; Melloh, Markus; Marsh, Reginald; Baxter, G David; Dowell, Anthony

2014-01-01

Objectives To develop an instrument to assess attitudes and underlying beliefs about back pain, and subsequently investigate its internal consistency and underlying structures. Design The instrument was developed by a multidisciplinary team of clinicians and researchers based on analysis of qualitative interviews with people experiencing acute and chronic back pain. Exploratory analysis was conducted using data from a population-based cross-sectional survey. Setting Qualitative interviews with community-based participants and subsequent postal survey. Participants Instrument development informed by interviews with 12 participants with acute back pain and 11 participants with chronic back pain. Data for exploratory analysis collected from New Zealand residents and citizens aged 18 years and above. 1000 participants were randomly selected from the New Zealand Electoral Roll. 602 valid responses were received. Measures The 34-item Back Pain Attitudes Questionnaire (Back-PAQ) was developed. Internal consistency was evaluated by the Cronbach α coefficient. Exploratory analysis investigated the structure of the data using Principal Component Analysis. Results The 34-item long form of the scale had acceptable internal consistency (α=0.70; 95% CI 0.66 to 0.73). Exploratory analysis identified five two-item principal components which accounted for 74% of the variance in the reduced data set: ‘vulnerability of the back’; ‘relationship between back pain and injury’; ‘activity participation while experiencing back pain’; ‘prognosis of back pain’ and ‘psychological influences on recovery’. Internal consistency was acceptable for the reduced 10-item scale (α=0.61; 95% CI 0.56 to 0.66) and the identified components (α between 0.50 and 0.78). Conclusions The 34-item long form of the scale may be appropriate for use in future cross-sectional studies. The 10-item short form may be appropriate for use as a screening tool, or an outcome assessment instrument. Further testing of the 10-item Back-PAQ's construct validity, reliability, responsiveness to change and predictive ability needs to be conducted. PMID:24860003

Geologic columns for the ICDP-USGS Eyreville A and B cores, Chesapeake Bay impact structure: Sediment-clast breccias, 1096 to 444 m depth

USGS Publications Warehouse

Edwards, L.E.; Powars, D.S.; Gohn, G.S.; Dypvik, H.

2009-01-01

The Eyreville A and B cores, recovered from the "moat" of the Chesapeake Bay impact structure, provide a thick section of sediment-clast breccias and minor stratified sediments from 1095.74 to 443.90 m. This paper discusses the components of these breccias, presents a geologic column and descriptive lithologic framework for them, and formalizes the Exmore Formation. From 1095.74 to ??867 m, the cores consist of nonmarine sediment boulders and sand (rare blocks up to 15.3 m intersected diameter). A sharp contact in both cores at ??867 m marks the lowest clayey, silty, glauconitic quartz sand that constitutes the base of the Exmore Formation and its lower diamicton member. Here, material derived from the upper sediment target layers, as well as some impact ejecta, occurs. The block-dominated member of the Exmore Formation, from ??855-618.23 m, consists of nonmarine sediment blocks and boulders (up to 45.5 m) that are juxtaposed complexly. Blocks of oxidized clay are an important component. Above 618.23 m, which is the base of the informal upper diamicton member of the Exmore Formation, the glauconitic matrix is a consistent component in diamicton layers between nonmarine sediment clasts that decrease in size upward in the section. Crystalline-rock clasts are not randomly distributed but rather form local concentrations. The upper part of the Exmore Formation consists of crudely fining-upward sandy packages capped by laminated silt and clay. The overlap interval of Eyreville A and B (940-??760 m) allows recognition of local similarities and differences in the breccias. ?? 2009 The Geological Society of America.

The Impact of State Legislation and Model Policies on Bullying in Schools.

PubMed

Terry, Amanda

2018-04-01

The purpose of this study was to determine the impact of the coverage of state legislation and the expansiveness ratings of state model policies on the state-level prevalence of bullying in schools. The state-level prevalence of bullying in schools was based on cross-sectional data from the 2013 High School Youth Risk Behavior Survey. Multiple regression was conducted to determine whether the coverage of state legislation and the expansiveness rating of a state model policy affected the state-level prevalence of bullying in schools. The purpose and definition category of components in state legislation and the expansiveness rating of a state model policy were statistically significant predictors of the state-level prevalence of bullying in schools. The other 3 categories of components in state legislation-District Policy Development and Review, District Policy Components, and Additional Components-were not statistically significant predictors in the model. Extensive coverage in the purpose and definition category of components in state legislation and a high expansiveness rating of a state model policy may be important in efforts to reduce bullying in schools. Improving these areas may reduce the state-level prevalence of bullying in schools. © 2018, American School Health Association.

Report of material and equipment section`s activities at New York Shipbuilding Corporation during fabrication of AXC 167 1/2 starting May 18, 1951. Part 7, Section 3

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stewart, J.R.

1954-04-28

This document provides Part VII, Section III and Section IV of the report of the Material and Equipment Section`s activities at the New York Shipbuilding Corporation. The fabrication, inspection, and testing of reactor components is detailed.

12 CFR 502.28 - How does OTS determine the organizational form component for a savings and loan holding company?

Code of Federal Regulations, 2010 CFR

2010-01-01

... component for a savings and loan holding company? 502.28 Section 502.28 Banks and Banking OFFICE OF THRIFT SUPERVISION, DEPARTMENT OF THE TREASURY ASSESSMENTS AND FEES Assessments Savings and Loan Holding Companies... savings and loan holding company that OTS regulates under section 10(l) of the HOLA. OTS will compute your...

78 FR 59732 - Revisions to Design of Structures, Components, Equipment, and Systems

Federal Register 2010, 2011, 2012, 2013, 2014

2013-09-27

...,'' Section 3.7.2, ``Seismic System Analysis,'' Section 3.7.3, ``Seismic Subsystem Analysis,'' Section 3.8.1... Analysis,'' (Accession No. ML13198A223); Section 3.7.3, ``Seismic Subsystem Analysis,'' (Accession No..., ``Seismic System Analysis,'' Section 3.7.3, ``Seismic Subsystem Analysis,'' Section 3.8.1, ``Concrete...

Technique of estimation of actual strength of a gas pipeline section at its deformation in landslide action zone

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tcherni, V.P.

1996-12-31

The technique is given which permits determination of stress and strain state (SSS) and estimation of actual strength of a section of a buried main gas pipeline (GP) in the case of its deformation in a landslide action zone. The technique is based on the use of three-dimensional coordinates of axial points of the deformed GP section. These coordinates are received by a full-scale survey. The deformed axis of the surveyed GP section is described by the polynomial. The unknown coefficients of the polynomial can be determined from the boundary conditions at points of connection with contiguous undeformed sections asmore » well as by use of minimization methods in mathematical processing of full-scale survey results. The resulting form of GP section`s axis allows one to determine curvatures and, accordingly, bending moments along all the length of the considered section. The influence of soil resistance to longitudinal displacements of a pipeline is used to determine longitudinal forces. Resulting values of bending moments and axial forces as well as the known value of internal pressure are used to analyze all necessary components of an actual SSS of pipeline section and to estimate its strength by elastic analysis.« less

PDSM characterization for fabrication of free-space OXC optical components

NASA Astrophysics Data System (ADS)

Argueta, Victor; Fitzpatrick, Brianna

2017-11-01

In 2007 Dr Khine et al published a paper where they presented a technique using thermoplastics and PDMS to create microfluidic patterns1. Their technique involves printing a pattern in a polystyrene sheet using a laser printer. Once the pattern is transfer the polystyrene sheets they are heated to reduce their size. By printing the same pattern of the plastic sheets before heating, it is possible to control the height up to 80 μm and the width as thin as 65 μm1, 2. This technique is attractive to be used in optical fabrication due to its versatility, low cost and fast prototyping. However, in order to fabricate optical systems, we will need to control the refractive index of PDMS to allow design of basic optical components like waveguides, beam splitter, or diffuse reflectors; or more complex structures like interferometers, optical microfluidic lab-on-chip, micro-lens arrays. Several techniques exist to control the refractive index for PDMS either by controlling the curing temperature, the ratio between the base and curing agent, or by curing using UV light3-5. In this paper, we present the changes on refractive index by changing the curing temperature for different base/reaction agent ratios. We then apply these results to fabricate an optical component for a free-space optical cross-connect (OXC). Optical cross-connects are an important network element for constructing the next generation of optical networks, where provisioning (reconfiguration), scalability, and fast restoration will be needed6-8. The main attraction of all-optical switching is that it enables routing of optical data signals without the need for conversion to electrical signals, and therefore, is independent of data rate and data protocols. We have proposed previously9, 11 a new approach for an OXC. Our architecture is a free-space 3-D while still using digital MEMS. Our system is based on the optical White cell12, which consists of three spherical mirrors among which light can circulate. In Section II, we will briefly mention the basic characteristics of the binary White cell OXC configuration. Section III we will introduce the changes induced on curing PDMS, our SDD design and its fabrication for two different beam displacements. Finally, in Section IV, we will present the summary and conclusions of our work.

A study of internal structure in components made by additive manufacturing process using 3 D X-ray tomography

DOE Office of Scientific and Technical Information (OSTI.GOV)

Raguvarun, K., E-mail: prajagopal@iitm.ac.in; Balasubramaniam, Krishnan, E-mail: prajagopal@iitm.ac.in; Rajagopal, Prabhu, E-mail: prajagopal@iitm.ac.in

Additive manufacturing methods are gaining increasing popularity for rapidly and efficiently manufacturing parts and components in the industrial context, as well as for domestic applications. However, except when used for prototyping or rapid visualization of components, industries are concerned with the load carrying capacity and strength achievable by additive manufactured parts. In this paper, the wire-arc additive manufacturing (AM) process based on gas tungsten arc welding (GTAW) has been examined for the internal structure and constitution of components generated by the process. High-resolution 3D X-ray tomography is used to gain cut-views through wedge-shaped parts created using this GTAW additive manufacturingmore » process with titanium alloy materials. In this work, two different control conditions for the GTAW process are considered. The studies reveal clusters of porosities, located in periodic spatial intervals along the sample cross-section. Such internal defects can have a detrimental effect on the strength of the resulting AM components, as shown in destructive testing studies. Closer examination of this phenomenon shows that defect clusters are preferentially located at GTAW traversal path intervals. These results highlight the strong need for enhanced control of process parameters in ensuring components with minimal defects and higher strength.« less

A study of internal structure in components made by additive manufacturing process using 3 D X-ray tomography

NASA Astrophysics Data System (ADS)

Raguvarun, K.; Balasubramaniam, Krishnan; Rajagopal, Prabhu; Palanisamy, Suresh; Nagarajah, Romesh; Hoye, Nicholas; Curiri, Dominic; Kapoor, Ajay

2015-03-01

Additive manufacturing methods are gaining increasing popularity for rapidly and efficiently manufacturing parts and components in the industrial context, as well as for domestic applications. However, except when used for prototyping or rapid visualization of components, industries are concerned with the load carrying capacity and strength achievable by additive manufactured parts. In this paper, the wire-arc additive manufacturing (AM) process based on gas tungsten arc welding (GTAW) has been examined for the internal structure and constitution of components generated by the process. High-resolution 3D X-ray tomography is used to gain cut-views through wedge-shaped parts created using this GTAW additive manufacturing process with titanium alloy materials. In this work, two different control conditions for the GTAW process are considered. The studies reveal clusters of porosities, located in periodic spatial intervals along the sample cross-section. Such internal defects can have a detrimental effect on the strength of the resulting AM components, as shown in destructive testing studies. Closer examination of this phenomenon shows that defect clusters are preferentially located at GTAW traversal path intervals. These results highlight the strong need for enhanced control of process parameters in ensuring components with minimal defects and higher strength.

Implementation Challenges for Ceramic Matrix Composites in High Temperature Applications

NASA Technical Reports Server (NTRS)

Singh, Mrityunjay

2004-01-01

Ceramic matrix composites are leading candidate materials for a number of applications in aeronautics, space, energy, electronics, nuclear, and transportation industries. In the aeronautics and space exploration systems, these materials are being considered for applications in hot sections of jet engines such as the combustor liner, nozzle components, nose cones, leading edges of reentry vehicles and space propulsion components. Applications in the energy and environmental industries include radiant heater tubes, heat exchangers, heat recuperators, gas and diesel particulate filters (DPFs), and components for land based turbines for power generation. These materials are also being considered for use in the first wall and blanket components of fusion reactors. There are a number of critical issues and challenges related to successful implementation of composite materials. Fabrication of net and complex shape components with high density and tailorable matrix properties is quite expensive, and even then various desirable properties are not achievable. In this presentation, microstructure and thermomechanical properties of composites fabricated by two techniques (chemical vapor infiltration and melt infiltration), will be presented. In addition, critical need for robust joining and assembly technologies in successful implementation of these systems will be discussed. Other implementation issues will be discussed along with advantages and benefits of using these materials for various components in high temperature applications.

The twofold diagnosis of personality disorder: How do personality dysfunction and pathological traits increment each other at successive levels of the trait hierarchy?

PubMed

Bastiaansen, Leen; Hopwood, Christopher J; Van den Broeck, Joke; Rossi, Gina; Schotte, Christiaan; De Fruyt, Filip

2016-07-01

Besides the categorical classification of personality disorders (PDs) in Section II of the DSM-5 (American Psychiatric Association, 2013), which has been transferred as such from DSM-IV, Section III provides an alternative model to stimulate further research on the dimensional conceptualization of PDs. In this alternative system, a PD diagnosis is based on 2 essential criteria: impaired personality functioning and the presence of pathological traits. One topic that warrants further research concerns the incremental validity of these 2 components. The current study addresses this issue in a mixed community-patient sample (N = 233). First, Goldberg's (2006) "bass-ackwards" method was used to examine the hierarchical structure of pathological traits as measured by the Dimensional Assessment of Personality Pathology (DAPP-BQ; Livesley & Jackson, 2009). We then extracted a single higher order factor from the Severity Index of Personality Problems (SIPP-118; Verheul et al., 2008) to derive 1 coherent indicator of personality dysfunction. Correlation and hierarchical regression analyses were used to determine the incremental validity of the dysfunction factor versus the trait components at succeeding levels of the DAPP-BQ hierarchy. The results only partially supported the 2-component PD diagnosis, as traits and dysfunction appeared to have only limited incremental validity. Moreover, lower order traits were generally unable to outperform higher order components in predicting specific DSM-IV PDs. Implications for the conceptualization and assessment of personality pathology are discussed. (PsycINFO Database Record (c) 2016 APA, all rights reserved).

Oxfordian magnetostratigraphy of the Aguilón and Tosos sections (Iberian Range, Spain) and evidence of a pre-Oligocene overprint

NASA Astrophysics Data System (ADS)

Juárez, M. T.; Osete, M. L.; Meléndez, G.; Langereis, C. G.; Zijderveld, J. D. A.

1994-08-01

A composite magnetic polarity sequence has been constructed for the middle and late Oxfordian (late Jurassic) from four overlapping sections situated in both limbs of an anticline. Two stable magnetisation components could be isolated in every sample analyzed. Both components pass the fold test: a low-temperature secondary component, with Dec. = 340.9° and Inc. = 44.9° ( α95 = 1.7°), of pre-Oligocene age, showing always normal polarity, and a high-temperature primary component, with Dec. = 324.1° and Inc. = 40.6° (α 95 = 2.9°). The latter shows both normal and reversed polarities and provides the geomagnetic record for the late Jurassic. The magnetostratigraphy of the four overlapping sections has given consistent results and indicates that a high frequency of reversals characterises the pattern of the geomagnetic field during the middle to upper Oxfordian. The corresponding Oxfordian paleopole is Plat = 251.2°, Plong = 55.9° ( α95 = 3.1).

North Massif lithologies and chemical compositions viewed from 2-4 mm particles of soil sample 76503

NASA Technical Reports Server (NTRS)

Bishop, Kaylynn M.; Jolliff, Bradley L.; Korotev, Randy L.; Haskin, Larry A.

1992-01-01

We identify the lithologic and compositional components of soil 76503 based on INAA of 243 2-4-mm particles and 72 thin sections from these and associated 1-2-mm particles (76502). We present a statistical distribution of the major compositional types as the first step of a detailed comparative study of the North and South Massifs. The soil sample was collected well away from any boulder and is more representative of typical North Massif material than any single large rock or boulder sample. So far, our examination of the 76503 particles has provided a better definition of precursor igneous lithologies and their petrogenetic relationships. It has enabled us to refine the nature of mixing components for the North Massif less than 1-mm fines. It has confirmed the differences in lithologies and their proportions between materials of the North and South Massifs; e.g., the North Massif is distinguished by the absence of a 72275-type KREEP component, the abundance of a highly magnesian igneous component, and the absence of certain types of melt compositions found in the South Massif samples.

Elastic/Inelastic Measurement Project

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yates, Steven; Hicks, Sally; Vanhoy, Jeffrey

2016-03-01

The work scope involves the measurement of neutron scattering from natural sodium ( 23Na) and two isotopes of iron, 56Fe and 54Fe. Angular distributions, i.e., differential cross sections, of the scattered neutrons will be measured for 5 to 10 incident neutron energies per year. The work of the first year concentrates on 23Na, while the enriched iron samples are procured. Differential neutron scattering cross sections provide information to guide nuclear reaction model calculations in the low-­energy (few MeV) fast-­neutron region. This region lies just above the isolated resonance region, which in general is well studied; however, model calculations are difficultmore » in this region because overlapping resonance structure is evident and direct nuclear reactions are becoming important. The standard optical model treatment exhibits good predictive ability for the wide-­region average cross sections but cannot treat the overlapping resonance features. In addition, models that do predict the direct reaction component must be guided by measurements to describe correctly the strength of the direct component, e.g., β 2 must be known to describe the direct component of the scattering to the first excited state. Measurements of the elastic scattering differential cross sections guide the optical model calculations, while inelastic differential cross sections provide the crucial information for correctly describing the direct component. Activities occurring during the performance period are described.« less

Beyond E 11

NASA Astrophysics Data System (ADS)

Bossard, Guillaume; Kleinschmidt, Axel; Palmkvist, Jakob; Pope, Christopher N.; Sezgin, Ergin

2017-05-01

We study the non-linear realisation of E 11 originally proposed by West with particular emphasis on the issue of linearised gauge invariance. Our analysis shows even at low levels that the conjectured equations can only be invariant under local gauge transformations if a certain section condition that has appeared in a different context in the E 11 literature is satisfied. This section condition also generalises the one known from exceptional field theory. Even with the section condition, the E 11 duality equation for gravity is known to miss the trace component of the spin connection. We propose an extended scheme based on an infinite-dimensional Lie superalgebra, called the tensor hierarchy algebra, that incorporates the section condition and resolves the above issue. The tensor hierarchy algebra defines a generalised differential complex, which provides a systematic description of gauge invariance and Bianchi identities. It furthermore provides an E 11 representation for the field strengths, for which we define a twisted first order self-duality equation underlying the dynamics.

Ion Elevators and Escalators in Multilevel Structures for Lossless Ion Manipulations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ibrahim, Yehia M.; Hamid, Ahmed M.; Cox, Jonathan T.

2017-01-19

We describe two approaches based upon ion ‘elevator’ and ‘escalator’ components that allow moving ions to different levels in structures for lossless ion manipulations (SLIM). Guided by ion motion simulations we designed elevator and escalator components providing essentially lossless transmission in multi-level designs based upon ion current measurements. The ion elevator design allowed ions to efficiently bridge a 4 mm gap between levels. The component was integrated in a SLIM and coupled to a QTOF mass spectrometer using an ion funnel interface to evaluate the m/z range transmitted as compared to transmission within a level (e.g. in a linear section).more » Mass spectra for singly-charged ions of m/z 600-2700 produced similar mass spectra for both elevator and straight (linear motion) components. In the ion escalator design, traveling waves (TW) were utilized to transport ions efficiently between two SLIM levels. Ion current measurements and ion mobility (IM) spectrometry analysis illustrated that ions can be transported between TW-SLIM levels with no significant loss of either ions or IM resolution. These developments provide a path for the development of multilevel designs providing e.g. much longer IM path lengths, more compact designs, and the implementation of much more complex SLIM devices in which e.g. different levels may operate at different temperatures or with different gases.« less

Direct Visualization of the Outer Membrane of Mycobacteria and Corynebacteria in Their Native State▿ †

PubMed Central

Zuber, Benoît; Chami, Mohamed; Houssin, Christine; Dubochet, Jacques; Griffiths, Gareth; Daffé, Mamadou

2008-01-01

The cell envelope of mycobacteria, which include the causative agents of tuberculosis and leprosy, is crucial for their success as pathogens. Despite a continued strong emphasis on identifying the multiple chemical components of this envelope, it has proven difficult to combine its components into a comprehensive structural model, primarily because the available ultrastructural data rely on conventional electron microscopy embedding and sectioning, which are known to induce artifacts. The existence of an outer membrane bilayer has long been postulated but has never been directly observed by electron microscopy of ultrathin sections. Here we have used cryo-electron microscopy of vitreous sections (CEMOVIS) to perform a detailed ultrastructural analysis of three species belonging to the Corynebacterineae suborder, namely, Mycobacterium bovis BCG, Mycobacterium smegmatis, and Corynebacterium glutamicum, in their native state. We provide new information that accurately describes the different layers of the mycobacterial cell envelope and challenges current models of the organization of its components. We show a direct visualization of an outer membrane, analogous to that found in gram-negative bacteria, in the three bacterial species examined. Furthermore, we demonstrate that mycolic acids, the hallmark of mycobacteria and related genera, are essential for the formation of this outer membrane. In addition, a granular layer and a low-density zone typifying the periplasmic space of gram-positive bacteria are apparent in CEMOVIS images of mycobacteria and corynebacteria. Based on our observations, a model of the organization of the lipids in the outer membrane is proposed. The architecture we describe should serve as a reference for future studies to relate the structure of the mycobacterial cell envelope to its function. PMID:18567661

Direct visualization of the outer membrane of mycobacteria and corynebacteria in their native state.

PubMed

Zuber, Benoît; Chami, Mohamed; Houssin, Christine; Dubochet, Jacques; Griffiths, Gareth; Daffé, Mamadou

2008-08-01

The cell envelope of mycobacteria, which include the causative agents of tuberculosis and leprosy, is crucial for their success as pathogens. Despite a continued strong emphasis on identifying the multiple chemical components of this envelope, it has proven difficult to combine its components into a comprehensive structural model, primarily because the available ultrastructural data rely on conventional electron microscopy embedding and sectioning, which are known to induce artifacts. The existence of an outer membrane bilayer has long been postulated but has never been directly observed by electron microscopy of ultrathin sections. Here we have used cryo-electron microscopy of vitreous sections (CEMOVIS) to perform a detailed ultrastructural analysis of three species belonging to the Corynebacterineae suborder, namely, Mycobacterium bovis BCG, Mycobacterium smegmatis, and Corynebacterium glutamicum, in their native state. We provide new information that accurately describes the different layers of the mycobacterial cell envelope and challenges current models of the organization of its components. We show a direct visualization of an outer membrane, analogous to that found in gram-negative bacteria, in the three bacterial species examined. Furthermore, we demonstrate that mycolic acids, the hallmark of mycobacteria and related genera, are essential for the formation of this outer membrane. In addition, a granular layer and a low-density zone typifying the periplasmic space of gram-positive bacteria are apparent in CEMOVIS images of mycobacteria and corynebacteria. Based on our observations, a model of the organization of the lipids in the outer membrane is proposed. The architecture we describe should serve as a reference for future studies to relate the structure of the mycobacterial cell envelope to its function.

NASA Tech Briefs, November 2001. Volume 25, No. 11

NASA Technical Reports Server (NTRS)

2001-01-01

Topics include: special coverage section on data acquisition, and sections on electronic components and systems, software, materials, machinery/automation, physical sciences, book and reports, and a special section of Photonics Tech Briefs.

NASA Tech Briefs, September 2001. Volume 25, No. 9

NASA Technical Reports Server (NTRS)

2001-01-01

Topics include: special coverage section on sensors, and sections on electronic components systems, software, materials, machinery/automation, manufacturing/fabrication, bio-medical, book and reports, and a special section of Photonics Tech Briefs.

46 CFR 54.01-25 - Miscellaneous pressure components (modifies UG-11).

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 2 2014-10-01 2014-10-01 false Miscellaneous pressure components (modifies UG-11). 54.01-25 Section 54.01-25 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING PRESSURE VESSELS General Requirements § 54.01-25 Miscellaneous pressure components (modifies UG-11). (a) Pressure components for pressure...

46 CFR 54.01-25 - Miscellaneous pressure components (modifies UG-11).

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 2 2011-10-01 2011-10-01 false Miscellaneous pressure components (modifies UG-11). 54.01-25 Section 54.01-25 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING PRESSURE VESSELS General Requirements § 54.01-25 Miscellaneous pressure components (modifies UG-11). (a) Pressure components for pressure...

46 CFR 54.01-25 - Miscellaneous pressure components (modifies UG-11).

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 2 2013-10-01 2013-10-01 false Miscellaneous pressure components (modifies UG-11). 54.01-25 Section 54.01-25 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING PRESSURE VESSELS General Requirements § 54.01-25 Miscellaneous pressure components (modifies UG-11). (a) Pressure components for pressure...

46 CFR 54.01-25 - Miscellaneous pressure components (modifies UG-11).

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Miscellaneous pressure components (modifies UG-11). 54.01-25 Section 54.01-25 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING PRESSURE VESSELS General Requirements § 54.01-25 Miscellaneous pressure components (modifies UG-11). (a) Pressure components for pressure...

46 CFR 54.01-25 - Miscellaneous pressure components (modifies UG-11).

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 2 2012-10-01 2012-10-01 false Miscellaneous pressure components (modifies UG-11). 54.01-25 Section 54.01-25 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING PRESSURE VESSELS General Requirements § 54.01-25 Miscellaneous pressure components (modifies UG-11). (a) Pressure components for pressure...

49 CFR 393.203 - Cab and body components.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 5 2011-10-01 2011-10-01 false Cab and body components. 393.203 Section 393.203... NECESSARY FOR SAFE OPERATION Frames, Cab and Body Components, Wheels, Steering, and Suspension Systems § 393.203 Cab and body components. (a) The cab compartment doors or door parts used as an entrance or exist...

Directions in implementation research methods for behavioral and social science.

PubMed

Irwin, Molly; Supplee, Lauren H

2012-10-01

There is a growing interest, by researchers, policymakers, and practitioners, in evidence-based policy and practice. As a result, more dollars are being invested in program evaluation in order to establish "what works," and in some cases, funding is specifically tied to those programs found to be effective. However, reproducing positive effects found in research requires more than simply adopting an evidence-based program. Implementation research can provide guidance on which components of an intervention matter most for program impacts and how implementation components can best be implemented. However, while the body of rigorous research on effective practices continues to grow, research on implementation lags behind. To address these issues, the Administration for Children and Families and federal partners convened a roundtable meeting entitled, Improving Implementation Research Methods for Behavioral and Social Science, in the fall of 2010. This special section of the Journal of Behavioral Health Services & Research includes papers from the roundtable and highlights the role implementation science can play in shedding light on the difficult task of taking evidence-based practices to scale.

Crash energy absorption of two-segment crash box with holes under frontal load

NASA Astrophysics Data System (ADS)

Choiron, Moch. Agus; Sudjito, Hidayati, Nafisah Arina

2016-03-01

Crash box is one of the passive safety components which designed as an impact energy absorber during collision. Crash box designs have been developed in order to obtain the optimum crashworthiness performance. Circular cross section was first investigated with one segment design, it rather influenced by its length which is being sensitive to the buckling occurrence. In this study, the two-segment crash box design with additional holes is investigated and deformation behavior and crash energy absorption are observed. The crash box modelling is performed by finite element analysis. The crash test components were impactor, crash box, and fixed rigid base. Impactor and the fixed base material are modelled as a rigid, and crash box material as bilinear isotropic hardening. Crash box length of 100 mm and frontal crash velocity of 16 km/jam are selected. Crash box material of Aluminum Alloy is used. Based on simulation results, it can be shown that holes configuration with 2 holes and ¾ length locations have the largest crash energy absorption. This condition associated with deformation pattern, this crash box model produces axisymmetric mode than other models.

Laser polishing of additive manufactured Ti alloys

NASA Astrophysics Data System (ADS)

Ma, C. P.; Guan, Y. C.; Zhou, W.

2017-06-01

Laser-based additive manufacturing has attracted much attention as a promising 3D printing method for metallic components in recent years. However, surface roughness of additive manufactured components has been considered as a challenge to achieve high performance. In this work, we demonstrate the capability of fiber laser in polishing rough surface of additive manufactured Ti-based alloys as Ti-6Al-4V and TC11. Both as-received surface and laser-polished surfaces as well as cross-section subsurfaces were analyzed carefully by White-Light Interference, Confocal Microscope, Focus Ion Beam, Scanning Electron Microscopy, Energy Dispersive Spectrometer, and X-ray Diffraction. Results revealed that as-received Ti-based alloys with surface roughness more than 5 μm could be reduce to less than 1 μm through laser polishing process. Moreover, microstructure, microhardness and wear resistance of laser-polished zone was investigated in order to examine the thermal effect of laser polishing processing on the substrate of additive manufactured Ti alloys. This proof-of-concept process has the potential to effectively improve the surface roughness of additive manufactured metallic alloy by local polishing method without damage to the substrate.

Expert system technology

NASA Technical Reports Server (NTRS)

Prince, Mary Ellen

1987-01-01

The expert system is a computer program which attempts to reproduce the problem-solving behavior of an expert, who is able to view problems from a broad perspective and arrive at conclusions rapidly, using intuition, shortcuts, and analogies to previous situations. Expert systems are a departure from the usual artificial intelligence approach to problem solving. Researchers have traditionally tried to develop general modes of human intelligence that could be applied to many different situations. Expert systems, on the other hand, tend to rely on large quantities of domain specific knowledge, much of it heuristic. The reasoning component of the system is relatively simple and straightforward. For this reason, expert systems are often called knowledge based systems. The report expands on the foregoing. Section 1 discusses the architecture of a typical expert system. Section 2 deals with the characteristics that make a problem a suitable candidate for expert system solution. Section 3 surveys current technology, describing some of the software aids available for expert system development. Section 4 discusses the limitations of the latter. The concluding section makes predictions of future trends.

Report of material and equipment section`s activities at New York Shipbuilding Corporation during fabrication of AXC 167 1/2 starting May 18, 1951. Part 7, Section 1: Paragraphs 1--14

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stewart, J.R.

1954-02-28

This document provides Part VII, Section I, Paragraphs 1 through 16 and Part VII, Section II of the Material and Equipment Section`s activities during the fabrication of reactor components and vessels at the New York Shipbuilding Corporation.

Thermal barrier coatings issues in advanced land-based gas turbines

NASA Technical Reports Server (NTRS)

Parks, W. P.; Lee, W. Y.; Wright, I. G.

1995-01-01

The Department of Energy's Advanced Turbine System (ATS) program is aimed at forecasting the development of a new generation of land-based gas turbine systems with overall efficiencies significantly beyond those of current state-of-the-art machines, as well as greatly increased times between inspection and refurbishment, improved environmental impact, and decreased cost. The proposed duty cycle of ATS turbines will require the use of different criteria in the design of the materials for the critical hot gas path components. In particular, thermal barrier coatings will be an essential feature of the hot gas path components in these machines. While such coatings are routinely used in high-performance aircraft engines and are becoming established in land-based turbines, the requirements of the ATS turbine application are sufficiently different that significant improvements in thermal barrier coating technology will be necessary. In particular, it appears that thermal barrier coatings will have to function on all airfoil sections of the first stage vanes and blades to provide the significant temperature reduction required. In contrast, such coatings applied to the blades and vances of advanced aircraft engines are intended primarily to reduce air cooling requirements and extend component lifetime; failure of those coatings can be tolerated without jeopardizing mechanical or corrosion performance. A major difference is that in ATS turbines these components will be totally reliant on thermal barrier coatings which will, therefore, need to be highly reliable even over the leading edges of first stage blades. Obviously, the ATS program provides a very challenging opportunity for TBC's, and involves some significant opportunities to extend this technology.

Fabricating cooled electronic system with liquid-cooled cold plate and thermal spreader

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chainer, Timothy J.; Graybill, David P.; Iyengar, Madhusudan K.

Methods are provided for facilitating cooling of an electronic component. The method includes providing a liquid-cooled cold plate and a thermal spreader associated with the cold plate. The cold plate includes multiple coolant-carrying channel sections extending within the cold plate, and a thermal conduction surface with a larger surface area than a surface area of the component to be cooled. The thermal spreader includes one or more heat pipes including multiple heat pipe sections. One or more heat pipe sections are partially aligned to a first region of the cold plate, that is, where aligned to the surface to bemore » cooled, and partially aligned to a second region of the cold plate, which is outside the first region. The one or more heat pipes facilitate distribution of heat from the electronic component to coolant-carrying channel sections of the cold plate located in the second region of the cold plate.« less

Fabricating cooled electronic system with liquid-cooled cold plate and thermal spreader

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chainer, Timothy J.; Graybill, David P.; Iyengar, Madhusudan K.

Methods are provided for facilitating cooling of an electronic component. The methods include providing a liquid-cooled cold plate and a thermal spreader associated with the cold plate. The cold plate includes multiple coolant-carrying channel sections extending within the cold plate, and a thermal conduction surface with a larger surface area than a surface area of the component to be cooled. The thermal spreader includes one or more heat pipes including multiple heat pipe sections. One or more heat pipe sections are partially aligned to a first region of the cold plate, that is, where aligned to the surface to bemore » cooled, and partially aligned to a second region of the cold plate, which is outside the first region. The one or more heat pipes facilitate distribution of heat from the electronic component to coolant-carrying channel sections of the cold plate located in the second region of the cold plate.« less

Separation of pedogenic and lithogenic components of magnetic susceptibility in the Chinese loess/palaeosol sequence as determined by the CBD procedure and a mixing analysis

NASA Astrophysics Data System (ADS)

Vidic, Nataša. J.; TenPas, Jeff D.; Verosub, Kenneth L.; Singer, Michael J.

2000-08-01

Magnetic susceptibility variations in the Chinese loess/palaeosol sequences have been used extensively for palaeoclimatic interpretations. The magnetic signal of these sequences must be divided into lithogenic and pedogenic components because the palaeoclimatic record is primarily reflected in the pedogenic component. In this paper we compare two methods for separating the pedogenic and lithogenic components of the magnetic susceptibility signal: the citrate-bicarbonate-dithionite (CBD) extraction procedure, and a mixing analysis. Both methods yield good estimates of the pedogenic component, especially for the palaeosols. The CBD procedure underestimates the lithogenic component and overestimates the pedogenic component. The magnitude of this effect is moderately high in loess layers but almost negligible in palaeosols. The mixing model overestimates the lithogenic component and underestimates the pedogenic component. Both methods can be adjusted to yield better estimates of both components. The lithogenic susceptibility, as determined by either method, suggests that palaeoclimatic interpretations based only on total susceptibility will be in error and that a single estimate of the average lithogenic susceptibility is not an accurate basis for adjusting the total susceptibility. A long-term decline in lithogenic susceptibility with depth in the section suggests more intense or prolonged periods of weathering associated with the formation of the older palaeosols. The CBD procedure provides the most comprehensive information on the magnitude of the components and magnetic mineralogy of loess and palaeosols. However, the mixing analysis provides a sensitive, rapid, and easily applied alternative to the CBD procedure. A combination of the two approaches provides the most powerful and perhaps the most accurate way of separating the magnetic susceptibility components.

A method for radiological characterization based on fluence conversion coefficients

NASA Astrophysics Data System (ADS)

Froeschl, Robert

2018-06-01

Radiological characterization of components in accelerator environments is often required to ensure adequate radiation protection during maintenance, transport and handling as well as for the selection of the proper disposal pathway. The relevant quantities are typical the weighted sums of specific activities with radionuclide-specific weighting coefficients. Traditional methods based on Monte Carlo simulations are radionuclide creation-event based or the particle fluences in the regions of interest are scored and then off-line weighted with radionuclide production cross sections. The presented method bases the radiological characterization on a set of fluence conversion coefficients. For a given irradiation profile and cool-down time, radionuclide production cross-sections, material composition and radionuclide-specific weighting coefficients, a set of particle type and energy dependent fluence conversion coefficients is computed. These fluence conversion coefficients can then be used in a Monte Carlo transport code to perform on-line weighting to directly obtain the desired radiological characterization, either by using built-in multiplier features such as in the PHITS code or by writing a dedicated user routine such as for the FLUKA code. The presented method has been validated against the standard event-based methods directly available in Monte Carlo transport codes.

Creep-fatigue life prediction for engine hot section materials (isotropic)

NASA Technical Reports Server (NTRS)

Moreno, V.

1982-01-01

The objectives of this program are the investigation of fundamental approaches to high temperature crack initiation life prediction, identification of specific modeling strategies and the development of specific models for component relevant loading conditions. A survey of the hot section material/coating systems used throughout the gas turbine industry is included. Two material/coating systems will be identified for the program. The material/coating system designated as the base system shall be used throughout Tasks 1-12. The alternate material/coating system will be used only in Task 12 for further evaluation of the models developed on the base material. In Task II, candidate life prediction approaches will be screened based on a set of criteria that includes experience of the approaches within the literature, correlation with isothermal data generated on the base material, and judgements relative to the applicability of the approach for the complex cycles to be considered in the option program. The two most promising approaches will be identified. Task 3 further evaluates the best approach using additional base material fatigue testing including verification tests. Task 4 consists of technical, schedular, financial and all other reporting requirements in accordance with the Reports of Work clause.

Rock magnetism and magnetostratigraphy of the loess-sol series of Ukraine (Roksolany, Boyanychi, and Korshev sections)

NASA Astrophysics Data System (ADS)

Bakhmutov, V. G.; Kazanskii, A. Yu.; Matasova, G. G.; Glavatskii, D. V.

2017-11-01

The results of the rock magnetic and paleomagnetic studies for the Quaternary loess-sol deposits of Ukraine are reported. The magnetic properties of the rocks composing the sections in the Pre-Black-Sea Depression (Roksolany) and Volyn Upland (Boyanychi and Korshev) are compared. Based on the highly precise measurements by modern instruments, the primary magnetization component is isolated in the rocks and its polarity is reliably determined in both the loess and soil horizons. The position of the Matuyama-Brunhes boundary in the Roksolany section is determined at a depth of 46.6 m at the contact of the Lubenskii and Martonoshskii soil horizons. This is consistent with the present-day notions of the group of Ukrainian scientists about the Quaternary stratigraphy of the south of Ukraine and inconsistent with the previous results that placed this boundary at a depth of 34 m in loesses above the PK7 level.

Geology of the surficial aquifer system, Broward County, Florida; lithologic logs

USGS Publications Warehouse

Causaras, C.R.

1985-01-01

The geologic framework of the surficial aquifer system, of which the Biscayne aquifer is the major component in Broward County, Florida, is presented in eight geologic cross sections. The cross sections are based on detailed lithologic logs of 27 test wells that were drilled, in the summer of 1981, through the sediments overlying the relatively impermeable units of the Hawthorn Formation, of Miocene age. The cross sections show the aquifer system as a wedge-shaped sequence of Cenozoic sediments. The aquifer thickness gradually decreases from more than 400 feet along the coast to about 160 feet in the west and southwest parts of Broward County. The sediments that comprise the aquifer system range in age from Pliocene to Pleistocene and are assigned to the following stratigraphic units from bottom to top: Tamiami Formation, Caloosahatchee Marl, Fort Thompson Formation, Key Largo Limestone, Anastasia Formation, Miami Oolite, and Pamlico Sand. (USGS)

NASA Tech Briefs, August 2001. Volume 25, No. 8

NASA Technical Reports Server (NTRS)

2001-01-01

Topics include: special coverage section on computers and peripherals, and sections on electronic components systems, software, materials, mechanics, manufacturing/fabrication, physical sciences, book and reports, and a special section of Motion Control Tech Briefs.

Loaded Transducer Fpr Downhole Drilling Component

DOEpatents

Hall, David R.; Hall, H. Tracy; Pixton, David; Dahlgren, Scott; Sneddon, Cameron; Briscoe, Michael; Fox, Joe

2005-07-05

A robust transmission element for transmitting information between downhole tools, such as sections of drill pipe, in the presence of hostile environmental conditions, such as heat, dirt, rocks, mud, fluids, lubricants, and the like. The transmission element maintains reliable connectivity between transmission elements, thereby providing an uninterrupted flow of information between drill string components. A transmission element is mounted within a recess proximate a mating surface of a downhole drilling component, such as a section of drill pipe. To close gaps present between transmission elements, transmission elements may be biased with a "spring force," urging them closer together.

Loaded transducer for downhole drilling components

DOEpatents

Hall, David R.; Hall, Jr., H. Tracy; Pixton, David S.; Briscoe, Michael A.; Dahlgren, Scott Steven; Fox, Joe; Sneddon, Cameron

2006-02-21

A robust transmission element for transmitting information between downhole tools, such as sections of drill pipe, in the presence of hostile environmental conditions, such as heat, dirt, rocks, mud, fluids, lubricants, and the like. The transmission element maintains reliable connectivity between transmission elements, thereby providing an uninterrupted flow of information between drill string components. A transmission element is mounted within a recess proximate a mating surface of a downhole drilling component, such as a section of drill pipe. To close gaps present between transmission elements, transmission elements may be biased with a "spring force, urging them closer together."

NASA Tech Briefs, December 2001. Volume 25, No. 12

NASA Technical Reports Server (NTRS)

2001-01-01

Topics include: special coverage section on sensors, and sections on electronic components and systems, software, materials, mechanics, information sciences, book and reports, and a special section of Motion Control Tech Briefs. It also contains a section celebrating the 25th anniversary of the publication.

Passive cooling system for a vehicle

DOEpatents

Hendricks, Terry Joseph; Thoensen, Thomas

2005-11-15

A passive cooling system for a vehicle (114) transfers heat from an overheated internal component, for example, an instrument panel (100), to an external portion (116) of the vehicle (114), for example, a side body panel (126). The passive cooling system includes one or more heat pipes (112) having an evaporator section (118) embedded in the overheated internal component and a condenser section (120) at the external portion (116) of the vehicle (114). The evaporator (118) and condenser (120) sections are in fluid communication. The passive cooling system may also include a thermally conductive film (140) for thermally connecting the evaporator sections (118) of the heat pipes (112) to each other and to the instrument panel (100).

Passive Cooling System for a Vehicle

DOEpatents

Hendricks, T. J.; Thoensen, T.

2005-11-15

A passive cooling system for a vehicle (114) transfers heat from an overheated internal component, for example, an instrument panel (100), to an external portion (116) of the vehicle (114), for example, a side body panel (126). The passive cooling system includes one or more heat pipes (112) having an evaporator section (118) embedded in the overheated internal component and a condenser section (120) at the external portion (116) of the vehicle (114). The evaporator (118) and condenser (120) sections are in fluid communication. The passive cooling system may also include a thermally conductive film (140) for thermally connecting the evaporator sections (118) of the heat pipes (112) to each other and to the instrument panel (100).

Mars vertical axis wind machines. The design of a Darreus and a Giromill for use on Mars

NASA Astrophysics Data System (ADS)

Brach, David; Dube, John; Kelly, Jon; Peterson, Joanna; Bollig, John; Gohr, Lisa; Mahoney, Kamin; Polidori, Dave

1992-05-01

This report contains the design of both a Darrieus and a Giromill for use on Mars. The report has been organized so that the interested reader may read only about one machine without having to read the entire report. Where components for the two machines differ greatly, separate sections have been allotted for each machine. Each section is complete; therefore, no relevant information is missed by reading only the section for the machine of interest. Also, when components for both machines are similar, both machines have been combined into one section. This is done so that the reader interested in both machines need not read the same information twice.

Mars vertical axis wind machines. The design of a Darreus and a Giromill for use on Mars

NASA Technical Reports Server (NTRS)

Brach, David; Dube, John; Kelly, Jon; Peterson, Joanna; Bollig, John; Gohr, Lisa; Mahoney, Kamin; Polidori, Dave

1992-01-01

This report contains the design of both a Darrieus and a Giromill for use on Mars. The report has been organized so that the interested reader may read only about one machine without having to read the entire report. Where components for the two machines differ greatly, separate sections have been allotted for each machine. Each section is complete; therefore, no relevant information is missed by reading only the section for the machine of interest. Also, when components for both machines are similar, both machines have been combined into one section. This is done so that the reader interested in both machines need not read the same information twice.

Multi-contrast MRI registration of carotid arteries based on cross-sectional images and lumen boundaries

NASA Astrophysics Data System (ADS)

Wu, Yu-Xia; Zhang, Xi; Xu, Xiao-Pan; Liu, Yang; Zhang, Guo-Peng; Li, Bao-Juan; Chen, Hui-Jun; Lu, Hong-Bing

2017-02-01

Ischemic stroke has great correlation with carotid atherosclerosis and is mostly caused by vulnerable plaques. It's particularly important to analysis the components of plaques for the detection of vulnerable plaques. Recently plaque analysis based on multi-contrast magnetic resonance imaging has attracted great attention. Though multi-contrast MR imaging has potentials in enhanced demonstration of carotid wall, its performance is hampered by the misalignment of different imaging sequences. In this study, a coarse-to-fine registration strategy based on cross-sectional images and wall boundaries is proposed to solve the problem. It includes two steps: a rigid step using the iterative closest points to register the centerlines of carotid artery extracted from multi-contrast MR images, and a non-rigid step using the thin plate spline to register the lumen boundaries of carotid artery. In the rigid step, the centerline was extracted by tracking the crosssectional images along the vessel direction calculated by Hessian matrix. In the non-rigid step, a shape context descriptor is introduced to find corresponding points of two similar boundaries. In addition, the deterministic annealing technique is used to find a globally optimized solution. The proposed strategy was evaluated by newly developed three-dimensional, fast and high resolution multi-contrast black blood MR imaging. Quantitative validation indicated that after registration, the overlap of two boundaries from different sequences is 95%, and their mean surface distance is 0.12 mm. In conclusion, the proposed algorithm has improved the accuracy of registration effectively for further component analysis of carotid plaques.

Development of a unified constitutive model for an isotropic nickel base superalloy Rene 80

NASA Technical Reports Server (NTRS)

Ramaswamy, V. G.; Vanstone, R. H.; Laflen, J. H.; Stouffer, D. C.

1988-01-01

Accurate analysis of stress-strain behavior is of critical importance in the evaluation of life capabilities of hot section turbine engine components such as turbine blades and vanes. The constitutive equations used in the finite element analysis of such components must be capable of modeling a variety of complex behavior exhibited at high temperatures by cast superalloys. The classical separation of plasticity and creep employed in most of the finite element codes in use today is known to be deficient in modeling elevated temperature time dependent phenomena. Rate dependent, unified constitutive theories can overcome many of these difficulties. A new unified constitutive theory was developed to model the high temperature, time dependent behavior of Rene' 80 which is a cast turbine blade and vane nickel base superalloy. Considerations in model development included the cyclic softening behavior of Rene' 80, rate independence at lower temperatures and the development of a new model for static recovery.

Oil and gas pipeline construction cost analysis and developing regression models for cost estimation

NASA Astrophysics Data System (ADS)

Thaduri, Ravi Kiran

In this study, cost data for 180 pipelines and 136 compressor stations have been analyzed. On the basis of the distribution analysis, regression models have been developed. Material, Labor, ROW and miscellaneous costs make up the total cost of a pipeline construction. The pipelines are analyzed based on different pipeline lengths, diameter, location, pipeline volume and year of completion. In a pipeline construction, labor costs dominate the total costs with a share of about 40%. Multiple non-linear regression models are developed to estimate the component costs of pipelines for various cross-sectional areas, lengths and locations. The Compressor stations are analyzed based on the capacity, year of completion and location. Unlike the pipeline costs, material costs dominate the total costs in the construction of compressor station, with an average share of about 50.6%. Land costs have very little influence on the total costs. Similar regression models are developed to estimate the component costs of compressor station for various capacities and locations.

Hyperspectral infrared nanoimaging of organic samples based on Fourier transform infrared nanospectroscopy

PubMed Central

Amenabar, Iban; Poly, Simon; Goikoetxea, Monika; Nuansing, Wiwat; Lasch, Peter; Hillenbrand, Rainer

2017-01-01

Infrared nanospectroscopy enables novel possibilities for chemical and structural analysis of nanocomposites, biomaterials or optoelectronic devices. Here we introduce hyperspectral infrared nanoimaging based on Fourier transform infrared nanospectroscopy with a tunable bandwidth-limited laser continuum. We describe the technical implementations and present hyperspectral infrared near-field images of about 5,000 pixel, each one covering the spectral range from 1,000 to 1,900 cm−1. To verify the technique and to demonstrate its application potential, we imaged a three-component polymer blend and a melanin granule in a human hair cross-section, and demonstrate that multivariate data analysis can be applied for extracting spatially resolved chemical information. Particularly, we demonstrate that distribution and chemical interaction between the polymer components can be mapped with a spatial resolution of about 30 nm. We foresee wide application potential of hyperspectral infrared nanoimaging for valuable chemical materials characterization and quality control in various fields ranging from materials sciences to biomedicine. PMID:28198384

Low-Thermal-Conductivity Pyrochlore Oxide Materials Developed for Advanced Thermal Barrier Coatings

NASA Technical Reports Server (NTRS)

Bansal, Narottam P.; Zhu, Dong-Ming

2005-01-01

When turbine engines operate at higher temperatures, they consume less fuel, have higher efficiencies, and have lower emissions. The upper-use temperatures of the base materials (superalloys, silicon-based ceramics, etc.) used for the hot-section components of turbine engines are limited by the physical, mechanical, and corrosion characteristics of these materials. Thermal barrier coatings (TBCs) are applied as thin layers on the surfaces of these materials to further increase the operating temperatures. The current state-of-the-art TBC material in commercial use is partially yttria-stabilized zirconia (YSZ), which is applied on engine components by plasma spraying or by electron-beam physical vapor deposition. At temperatures higher than 1000 C, YSZ layers are prone to sintering, which increases thermal conductivity and makes them less effective. The sintered and densified coatings can also reduce thermal stress and strain tolerance, which can reduce the coating s durability significantly. Alternate TBC materials with lower thermal conductivity and better sintering resistance are needed to further increase the operating temperature of turbine engines.

Hyperspectral infrared nanoimaging of organic samples based on Fourier transform infrared nanospectroscopy

NASA Astrophysics Data System (ADS)

Amenabar, Iban; Poly, Simon; Goikoetxea, Monika; Nuansing, Wiwat; Lasch, Peter; Hillenbrand, Rainer

2017-02-01

Infrared nanospectroscopy enables novel possibilities for chemical and structural analysis of nanocomposites, biomaterials or optoelectronic devices. Here we introduce hyperspectral infrared nanoimaging based on Fourier transform infrared nanospectroscopy with a tunable bandwidth-limited laser continuum. We describe the technical implementations and present hyperspectral infrared near-field images of about 5,000 pixel, each one covering the spectral range from 1,000 to 1,900 cm-1. To verify the technique and to demonstrate its application potential, we imaged a three-component polymer blend and a melanin granule in a human hair cross-section, and demonstrate that multivariate data analysis can be applied for extracting spatially resolved chemical information. Particularly, we demonstrate that distribution and chemical interaction between the polymer components can be mapped with a spatial resolution of about 30 nm. We foresee wide application potential of hyperspectral infrared nanoimaging for valuable chemical materials characterization and quality control in various fields ranging from materials sciences to biomedicine.

Report of material and equipment section`s activities at New York Shipbuilding Corporation during fabrication of AXC 167 1/2 starting May 18, 1951. Part 3

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stewart, J.R.

1954-05-26

This report provides Part III through VI of the Material and Equipment Section`s activities at New York Shipbuilding Corporation. Fabrication, inspection, and testing of reactor components are detailed.

NASA Tech Briefs, March 1999. Volume 23, No. 3

NASA Technical Reports Server (NTRS)

1999-01-01

Topics include: special coverage sections on CAD/CAE/PDM, industrial controls and sections on electronic components systems, materials, software, mechanics, machinery/automation, manufacturing/fabrication, physical sciences, book and reports, and a special section of Photonics Tech Briefs and a seconds special section of Rapid Product Development.

NASA Tech Briefs, April 1999. Volume 23, No. 4

NASA Technical Reports Server (NTRS)

1999-01-01

Topics include: special coverage sections on automotive technology, and CAM and sections on electronic components and systems, software, materials, machinery/automation, physical sciences, and a special section of Electronic Tech Briefs and Motion Control Tech Briefs.

NASA Tech Briefs, December 2000. Volume 24, No. 12

NASA Technical Reports Server (NTRS)

2000-01-01

Topics include: special coverage sections on Imaging/Video/Display Technology, and sections on electronic components and systems, test and measurement, software, information sciences, and special sections of Electronics Tech Briefs and Motion Control Tech Briefs.

NASA Tech Briefs, January 1999. Volume 23, Mp/ 1

NASA Technical Reports Server (NTRS)

1999-01-01

Topics include: special coverage sections on sensors and data acquisition and sections on electronic components and circuits, electronic software, materials, mechanics, bio-medical physical sciences, book and reports, and a special section of Photonics Tech Briefs.

40 CFR 141.716 - Source toolbox components.

Code of Federal Regulations, 2012 CFR

2012-07-01

... for Microbial Toolbox Components § 141.716 Source toolbox components. (a) Watershed control program. Systems receive 0.5-log Cryptosporidium treatment credit for implementing a watershed control program that meets the requirements of this section. (1) Systems that intend to apply for the watershed control...

40 CFR 141.716 - Source toolbox components.

Code of Federal Regulations, 2013 CFR

2013-07-01

... for Microbial Toolbox Components § 141.716 Source toolbox components. (a) Watershed control program. Systems receive 0.5-log Cryptosporidium treatment credit for implementing a watershed control program that meets the requirements of this section. (1) Systems that intend to apply for the watershed control...

40 CFR 141.716 - Source toolbox components.

Code of Federal Regulations, 2014 CFR

2014-07-01

... for Microbial Toolbox Components § 141.716 Source toolbox components. (a) Watershed control program. Systems receive 0.5-log Cryptosporidium treatment credit for implementing a watershed control program that meets the requirements of this section. (1) Systems that intend to apply for the watershed control...

Data transmission element for downhole drilling components

DOEpatents

Hall, David R.; Hall, Jr., H. Tracy; Pixton, David S.; Dahlgren, Scott; Fox, Joe; Sneddon, Cameron; Briscoe, Michael

2006-01-31

A robust data transmission element for transmitting information between downhole components, such as sections of drill pipe, in the presence of hostile environmental conditions, such as heat, dirt, rocks, mud, fluids, lubricants, and the like. The data transmission element components include a generally U-shaped annular housing, a generally U-shaped magnetically conductive, electrically insulating element such as ferrite, and an insulated conductor. Features on the magnetically conducting, electrically insulating element and the annular housing create a pocket when assembled. The data transmission element is filled with a polymer to retain the components within the annular housing by filling the pocket with the polymer. The polymer can bond with the annular housing and the insulated conductor but preferably not the magnetically conductive, electrically insulating element. A data transmission element is mounted within a recess proximate a mating surface of a downhole drilling component, such as a section of drill pipe.

Paleogeographic insights based on new U-Pb dates for altered tuffs in the Miocene Barstow Formation, California

USGS Publications Warehouse

Miller, David; Rosario, Jose E.; Leslie, Shannon R.; Vazquez, Jorge A.

2013-01-01

The type section of the Barstow Formation in the Mud Hills, north of Barstow, is a reference section for early to middle Miocene paleontology, magnetostratigraphy, and dated volcanic episodes. Thanks to this robust chronologic framework, much of the interpretation of the paleogeography of the region from about 18 Ma to 13 Ma is based on study of the rocks in the Mud Hills. Eastward from the type section, the Barstow Formation typically is altered and structurally complex, and therefore it is hard to fit into the patterns inferred for sedimentation at the type section. We have studied ten tuff beds in five locations, extracting zircons that are partly eruptive components of the volcanic ash and partly detrital. Ion microprobe dating of the zircons associated with the ashes allows us to improve stratigraphic correlations. Dated tuffs range from 19.3 Ma to ~14.8 Ma. In several of the sections, we dated tuffs in the range 16.2-16.5 Ma, about the same age as the ~16.3 Ma Rak Tuff in the type section. The beginning of lacustrine limestone, shale, and siltstone deposition varies significantly, from ~16.3 Ma in the type section to ~18.5 Ma in hills to the east and the Calico Mountains, and greater than 19.3 Ma at Harvard Hill. At ~16.3 Ma, the sedimentary rocks ranged (west to east) from silty sandstone and limestone, to mudstone with gypsum, to massive mudstone, and then to sandstone. If the sections have not been greatly shuffled by subsequent faulting, the picture that emerges is one of a broad basin whose center near the Yermo Hills was occupied by a lake that was much longer lived and deeper than to the east and west.

Deep Downhole Seismic Testing at the Waste Treatment Plant Site, Hanford, WA. Volume IV S-Wave Measurements in Borehole C4993 Seismic Records, Wave-Arrival Identifications and Interpreted S-Wave Velocity Profile.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stokoe, Kenneth H.; Li, Song Cheng; Cox, Brady R.

2007-06-06

In this volume (IV), all S-wave measurements are presented that were performed in Borehole C4993 at the Waste Treatment Plant (WTP) with T-Rex as the seismic source and the Lawrence Berkeley National Laboratory (LBNL) 3-D wireline geophone as the at-depth borehole receiver. S-wave measurements were performed over the depth range of 370 to 1300 ft, typically in 10-ft intervals. However, in some interbeds, 5-ft depth intervals were used, while below about 1200 ft, depth intervals of 20 ft were used. Shear (S) waves were generated by moving the base plate of T-Rex for a given number of cycles at amore » fixed frequency as discussed in Section 2. This process was repeated so that signal averaging in the time domain was performed using 3 to about 15 averages, with 5 averages typically used. In addition, a second average shear wave record was recorded by reversing the polarity of the motion of the T-Rex base plate. In this sense, all the signals recorded in the field were averaged signals. In all cases, the base plate was moving perpendicular to a radial line between the base plate and the borehole which is in and out of the plane of the figure shown in Figure 1.1. The definition of “in-line”, “cross-line”, “forward”, and “reversed” directions in items 2 and 3 of Section 2 was based on the moving direction of the base plate. In addition to the LBNL 3-D geophone, called the lower receiver herein, a 3-D geophone from Redpath Geophysics was fixed at a depth of 22 ft in Borehole C4993, and a 3-D geophone from the University of Texas (UT) was embedded near the borehole at about 1.5 ft below the ground surface. The Redpath geophone and the UT geophone were properly aligned so that one of the horizontal components in each geophone was aligned with the direction of horizontal shaking of the T-Rex base plate. This volume is organized into 12 sections as follows. Section 1: Introduction, Section 2: Explanation of Terminology, Section 3: Vs Profile at Borehole C4993, Sections 4 to 6: Unfiltered S-wave records of lower horizontal receiver, reaction mass, and reference receiver, respectively, Sections 7 to 9: Filtered S-wave signals of lower horizontal receiver, reaction mass and reference receiver, respectively, Section 10: Expanded and filtered S-wave signals of lower horizontal receiver, and Sections 11 and 12: Waterfall plots of unfiltered and filtered lower horizontal receiver signals, respectively.« less

Project W-320 acceptance test report for AY-farm electrical distribution

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bevins, R.R.

1998-04-02

This Acceptance Test Procedure (ATP) has been prepared to demonstrate that the AY-Farm Electrical Distribution System functions as required by the design criteria. This test is divided into three parts to support the planned construction schedule; Section 8 tests Mini-Power Pane AY102-PPI and the EES; Section 9 tests the SSS support systems; Section 10 tests the SSS and the Multi-Pak Group Control Panel. This test does not include the operation of end-use components (loads) supplied from the distribution system. Tests of the end-use components (loads) will be performed by other W-320 ATPs.

Novel approach of wavelet analysis for nonlinear ultrasonic measurements and fatigue assessment of jet engine components

NASA Astrophysics Data System (ADS)

Bunget, Gheorghe; Tilmon, Brevin; Yee, Andrew; Stewart, Dylan; Rogers, James; Webster, Matthew; Farinholt, Kevin; Friedersdorf, Fritz; Pepi, Marc; Ghoshal, Anindya

2018-04-01

Widespread damage in aging aircraft is becoming an increasing concern as both civil and military fleet operators are extending the service lifetime of their aircraft. Metallic components undergoing variable cyclic loadings eventually fatigue and form dislocations as precursors to ultimate failure. In order to characterize the progression of fatigue damage precursors (DP), the acoustic nonlinearity parameter is measured as the primary indicator. However, using proven standard ultrasonic technology for nonlinear measurements presents limitations for settings outside of the laboratory environment. This paper presents an approach for ultrasonic inspection through automated immersion scanning of hot section engine components where mature ultrasonic technology is used during periodic inspections. Nonlinear ultrasonic measurements were analyzed using wavelet analysis to extract multiple harmonics from the received signals. Measurements indicated strong correlations of nonlinearity coefficients and levels of fatigue in aluminum and Ni-based superalloys. This novel wavelet cross-correlation (WCC) algorithm is a potential technique to scan for fatigue damage precursors and identify critical locations for remaining life prediction.

Improving cancer treatment with cyclotron produced radionuclides. Comprehensive progress report, February 1, 1992--July 15, 1995

DOE Office of Scientific and Technical Information (OSTI.GOV)

Larson, S.M.; Finn, R.D.

1995-07-17

This research continues the long term goals of promoting nuclear medicine applications by improving the scientific basis for tumor diagnosis, treatment and treatment follow-up based on the use of cyclotron produced radiotracers in oncology. This program fits into the nuclear medicine component of DOE`s mission, which is aimed at enhancing the beneficial applications of radiation, radionuclides, and stable isotopes in the diagnosis, study and treatment of human diseases. The grant includes 3 interactive components: Radiochemistry/Cyclotron; Pharmacology/Immunology; and Imaging Physics. An essential strategy is as follows: novel radionuclides and radiotracers developed in the Radiochemistry/Section under the DOE grant during the 1992--1995more » will be employed in the Pharmacology/Immunology component in the period 1996--1999. Imaging Physics resolves relevant imaging related physics issues that arise during the experimentation that results. In addition to the basic research mission, this project also provides a basis for training of research scientists in radiochemistry, immunology, bioengineering and imaging physics.« less

Evaluation of hydrogels for soft tissue adhesives in vitro and in vivo analyses

NASA Astrophysics Data System (ADS)

Yuan, Liu; Fan, Wenshuai; Han, Linyingjun; Guo, Changan; Yan, Zuoqin; Zhu, Meifang; Mo, Xiumei

2018-03-01

In this study, natural materials (sodium alginate, dextran, gelatin and carboxymethyl chitosan) were modified to get aldehyde components and amino components. Upon mixing the two-component solutions together, four kinds of Schiff base hydrogels formed successfully within 5-300 s and could seal the wound tissue. The cytotoxicity tests of hydrogel extraction solution confirmed that the hydrogels are nontoxic materials. The adhesive ability was evaluated in vivo by measuring the adhesive strength after sealing the skin incisions on the back of rats. All the hydrogels showed higher adhesive strength than that of commercial fibrin glue and the blank control. The histological staining observation by hematoxylin and eosin staining (HE) and Masson's trichrome staining (MTC) methods suggested that the hydrogels had good biocompatibility and biodegradation in vivo. They have only normal initial inflammation to skin tissue and could improve the formation of new collagen in the incision section. So, the prepared hydrogels were both safe and effective tissue adhesive, which had the great potentials to be used as skin tissue adhesive.

X-ray edge singularity in resonant inelastic x-ray scattering (RIXS)

NASA Astrophysics Data System (ADS)

Markiewicz, Robert; Rehr, John; Bansil, Arun

2013-03-01

We develop a lattice model based on the theory of Mahan, Noziéres, and de Dominicis for x-ray absorption to explore the effect of the core hole on the RIXS cross section. The dominant part of the spectrum can be described in terms of the dynamic structure function S (q , ω) dressed by matrix element effects, but there is also a weak background associated with multi-electron-hole pair excitations. The model reproduces the decomposition of the RIXS spectrum into well- and poorly-screened components. An edge singularity arises at the threshold of both components. Fairly large lattice sizes are required to describe the continuum limit. Supported by DOE Grant DE-FG02-07ER46352 and facilitated by the DOE CMCSN, under grant number DE-SC0007091.

Comments on settling chamber design for quiet, blowdown wind tunnels

NASA Technical Reports Server (NTRS)

Beckwith, I. E.

1981-01-01

Transfer of an existing continous circuit supersonic wind tunnel to Langley and its operation there as a blowdown tunnel is planned. Flow disturbance requirements in the supply section and methods for reducing the high level broad band acoustic disturbances present in typical blowdown tunnels are reviewed. Based on recent data and the analysis of two blowdown facilities at Langley, methods for reducing the total turbulence levels in the settling chamber, including both acoustic and vorticity modes, to less than one percent are recommended. The pertinent design details of the damping screens and honeycomb and the recommended minimum pressure drop across the porous components providing the required two orders of magnitude attenuation of acoustic noise levels are given. A suggestion for the support structure of these high pressure drop porous components is offered.

Modeling the Webgraph: How Far We Are

NASA Astrophysics Data System (ADS)

Donato, Debora; Laura, Luigi; Leonardi, Stefano; Millozzi, Stefano

The following sections are included: * Introduction * Preliminaries * WebBase * In-degree and out-degree * PageRank * Bipartite cliques * Strongly connected components * Stochastic models of the webgraph * Models of the webgraph * A multi-layer model * Large scale simulation * Algorithmic techniques for generating and measuring webgraphs * Data representation and multifiles * Generating webgraphs * Traversal with two bits for each node * Semi-external breadth first search * Semi-external depth first search * Computation of the SCCs * Computation of the bow-tie regions * Disjoint bipartite cliques * PageRank * Summary and outlook

29 CFR 1919.32 - Specially designed blocks and components.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 29 Labor 7 2010-07-01 2010-07-01 false Specially designed blocks and components. 1919.32 Section 1919.32 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION... Treatment; Competent Persons § 1919.32 Specially designed blocks and components. (a) Blocks and connecting...

21 CFR 888.5890 - Noninvasive traction component.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Noninvasive traction component. 888.5890 Section 888.5890 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES ORTHOPEDIC DEVICES Surgical Devices § 888.5890 Noninvasive traction component. (a...

21 CFR 888.5890 - Noninvasive traction component.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Noninvasive traction component. 888.5890 Section 888.5890 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES ORTHOPEDIC DEVICES Surgical Devices § 888.5890 Noninvasive traction component. (a...

21 CFR 888.5890 - Noninvasive traction component.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Noninvasive traction component. 888.5890 Section 888.5890 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES ORTHOPEDIC DEVICES Surgical Devices § 888.5890 Noninvasive traction component. (a...

21 CFR 888.5890 - Noninvasive traction component.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Noninvasive traction component. 888.5890 Section 888.5890 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES ORTHOPEDIC DEVICES Surgical Devices § 888.5890 Noninvasive traction component. (a...

21 CFR 888.5890 - Noninvasive traction component.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Noninvasive traction component. 888.5890 Section 888.5890 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES ORTHOPEDIC DEVICES Surgical Devices § 888.5890 Noninvasive traction component. (a...

16 CFR 1509.4 - Spacing of unit components.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 16 Commercial Practices 2 2010-01-01 2010-01-01 false Spacing of unit components. 1509.4 Section 1509.4 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION FEDERAL HAZARDOUS SUBSTANCES ACT REGULATIONS REQUIREMENTS FOR NON-FULL-SIZE BABY CRIBS § 1509.4 Spacing of unit components. (a) Uniformly...

49 CFR 192.153 - Components fabricated by welding.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 3 2010-10-01 2010-10-01 false Components fabricated by welding. 192.153 Section....153 Components fabricated by welding. (a) Except for branch connections and assemblies of standard... welding, whose strength cannot be determined, must be established in accordance with paragraph UG-101 of...

21 CFR 890.5350 - Exercise component.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Exercise component. 890.5350 Section 890.5350 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES PHYSICAL MEDICINE DEVICES Physical Medicine Therapeutic Devices § 890.5350 Exercise component. (a...

21 CFR 890.5350 - Exercise component.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Exercise component. 890.5350 Section 890.5350 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES PHYSICAL MEDICINE DEVICES Physical Medicine Therapeutic Devices § 890.5350 Exercise component. (a...

21 CFR 890.5350 - Exercise component.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Exercise component. 890.5350 Section 890.5350 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES PHYSICAL MEDICINE DEVICES Physical Medicine Therapeutic Devices § 890.5350 Exercise component. (a...

21 CFR 890.5350 - Exercise component.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Exercise component. 890.5350 Section 890.5350 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES PHYSICAL MEDICINE DEVICES Physical Medicine Therapeutic Devices § 890.5350 Exercise component. (a...

21 CFR 890.5350 - Exercise component.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Exercise component. 890.5350 Section 890.5350 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES PHYSICAL MEDICINE DEVICES Physical Medicine Therapeutic Devices § 890.5350 Exercise component. (a...

49 CFR 192.153 - Components fabricated by welding.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 49 Transportation 3 2014-10-01 2014-10-01 false Components fabricated by welding. 192.153 Section....153 Components fabricated by welding. (a) Except for branch connections and assemblies of standard... welding, whose strength cannot be determined, must be established in accordance with paragraph UG-101 of...

49 CFR 192.153 - Components fabricated by welding.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 3 2011-10-01 2011-10-01 false Components fabricated by welding. 192.153 Section....153 Components fabricated by welding. (a) Except for branch connections and assemblies of standard... welding, whose strength cannot be determined, must be established in accordance with paragraph UG-101 of...

49 CFR 192.153 - Components fabricated by welding.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 49 Transportation 3 2013-10-01 2013-10-01 false Components fabricated by welding. 192.153 Section....153 Components fabricated by welding. (a) Except for branch connections and assemblies of standard... welding, whose strength cannot be determined, must be established in accordance with paragraph UG-101 of...

49 CFR 192.153 - Components fabricated by welding.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 49 Transportation 3 2012-10-01 2012-10-01 false Components fabricated by welding. 192.153 Section....153 Components fabricated by welding. (a) Except for branch connections and assemblies of standard... welding, whose strength cannot be determined, must be established in accordance with paragraph UG-101 of...

16 CFR 1509.5 - Component-spacing test apparatus.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 16 Commercial Practices 2 2011-01-01 2011-01-01 false Component-spacing test apparatus. 1509.5 Section 1509.5 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION FEDERAL HAZARDOUS SUBSTANCES ACT REGULATIONS REQUIREMENTS FOR NON-FULL-SIZE BABY CRIBS § 1509.5 Component-spacing test apparatus. (a) Loading...

16 CFR 1509.5 - Component-spacing test apparatus.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 16 Commercial Practices 2 2010-01-01 2010-01-01 false Component-spacing test apparatus. 1509.5 Section 1509.5 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION FEDERAL HAZARDOUS SUBSTANCES ACT REGULATIONS REQUIREMENTS FOR NON-FULL-SIZE BABY CRIBS § 1509.5 Component-spacing test apparatus. (a) Loading...

7 CFR 3201.80 - Electronic components cleaners.

Code of Federal Regulations, 2013 CFR

2013-01-01

... PROCUREMENT Designated Items § 3201.80 Electronic components cleaners. (a) Definition. Products that are designed to wash or remove dirt or extraneous matter from electronic parts, devices, circuits, or systems... 7 Agriculture 15 2013-01-01 2013-01-01 false Electronic components cleaners. 3201.80 Section 3201...

7 CFR 3201.80 - Electronic components cleaners.

Code of Federal Regulations, 2014 CFR

2014-01-01

... PROCUREMENT Designated Items § 3201.80 Electronic components cleaners. (a) Definition. Products that are designed to wash or remove dirt or extraneous matter from electronic parts, devices, circuits, or systems... 7 Agriculture 15 2014-01-01 2014-01-01 false Electronic components cleaners. 3201.80 Section 3201...

15 CFR 921.33 - Boundary changes, amendments to the management plan, and addition of multiple-site components.

Code of Federal Regulations, 2010 CFR

2010-01-01

... management plan, and addition of multiple-site components. 921.33 Section 921.33 Commerce and Foreign Trade... management plan, and addition of multiple-site components. (a) Changes in the boundary of a Reserve and major... management plan shall address goals and objectives for all components of the multi-site Reserve and the...

19 CFR 10.25 - Textile components cut to shape in the United States and assembled abroad.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 19 Customs Duties 1 2011-04-01 2011-04-01 false Textile components cut to shape in the United States and assembled abroad. 10.25 Section 10.25 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION... components cut to shape in the United States and assembled abroad. Where a textile component is cut to shape...

41 CFR 102-85.40 - What are the major components of the pricing policy?

Code of Federal Regulations, 2010 CFR

2010-07-01

... components of the pricing policy? 102-85.40 Section 102-85.40 Public Contracts and Property Management...-PRICING POLICY FOR OCCUPANCY IN GSA SPACE Pricing Policy-General § 102-85.40 What are the major components of the pricing policy? The major components of the pricing policy are: (a) An OA between a customer...

19 CFR 10.25 - Textile components cut to shape in the United States and assembled abroad.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 19 Customs Duties 1 2010-04-01 2010-04-01 false Textile components cut to shape in the United States and assembled abroad. 10.25 Section 10.25 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION... components cut to shape in the United States and assembled abroad. Where a textile component is cut to shape...

Transducer for downhole drilling components

DOEpatents

Hall, David R; Fox, Joe R

2006-05-30

A robust transmission element for transmitting information between downhole tools, such as sections of drill pipe, in the presence of hostile environmental conditions, such as heat, dirt, rocks, mud, fluids, lubricants, and the like. The transmission element maintains reliable connectivity between transmission elements, thereby providing an uninterrupted flow of information between drill string components. A transmission element is mounted within a recess proximate a mating surface of a downhole drilling component, such as a section of drill pipe. The transmission element may include an annular housing forming a trough, an electrical conductor disposed within the trough, and an MCEI material disposed between the annular housing and the electrical conductor.

Which Components of Medical Homes Reduce the Time Burden on Families of Children with Special Health Care Needs?

PubMed Central

Miller, Jane E; Nugent, Colleen N; Russell, Louise B

2015-01-01

Objectives To examine which components of medical homes affect time families spend arranging/coordinating health care for their children with special health care needs (CSHCNs) and providing health care at home. Data Sources 2009–2010 National Survey of Children with Special Health Care Needs (NS-CSHCN), a population-based survey of 40,242 CSHCNs. Study Design NS-CSHCN is a cross-sectional, observational study. We used generalized ordered logistic regression, testing for nonproportional odds in the associations between each of five medical home components and time burden, controlling for insurance, child health, and sociodemographics. Data Collection/Extraction Methods Medical home components were collected using Child and Adolescent Health Measurement Initiative definitions. Principal Findings Family-centered care, care coordination, and obtaining needed referrals were associated with 15–32 percent lower odds of time burdens arranging/coordinating and 16–19 percent lower odds providing health care. All five components together were associated with lower odds of time burdens, with greater reductions for higher burdens providing care. Conclusions Three of the five medical home components were associated with lower family time burdens arranging/coordinating and providing health care for children with chronic conditions. If the 55 percent of CSHCNs lacking medical homes had one, the share of families with time burdens arranging care could be reduced by 13 percent. PMID:25100200

Finite Element Based HWB Centerbody Structural Optimization and Weight Prediction

NASA Technical Reports Server (NTRS)

Gern, Frank H.

2012-01-01

This paper describes a scalable structural model suitable for Hybrid Wing Body (HWB) centerbody analysis and optimization. The geometry of the centerbody and primary wing structure is based on a Vehicle Sketch Pad (VSP) surface model of the aircraft and a FLOPS compatible parameterization of the centerbody. Structural analysis, optimization, and weight calculation are based on a Nastran finite element model of the primary HWB structural components, featuring centerbody, mid section, and outboard wing. Different centerbody designs like single bay or multi-bay options are analyzed and weight calculations are compared to current FLOPS results. For proper structural sizing and weight estimation, internal pressure and maneuver flight loads are applied. Results are presented for aerodynamic loads, deformations, and centerbody weight.

Structural cooling fluid tube for supporting a turbine component and supplying cooling fluid

DOE Office of Scientific and Technical Information (OSTI.GOV)

Charron, Richard; Pierce, Daniel

2015-02-24

A shaft cover support for a gas turbine engine is disclosed. The shaft cover support not only provides enhanced support to a shaft cover of the gas turbine engine, but also includes a cooling fluid chamber for passing fluids from a rotor air cooling supply conduit to an inner ring cooling manifold. As such, the shaft cover support accomplishes in a single component what was only partially accomplished in two components in conventional configurations. The shaft cover support may also provide additional stiffness and reduce interference of the flow from the compressor. In addition, the shaft cover support accommodates amore » transition section extending between compressor and turbine sections of the engine. The shaft cover support has a radially extending region that is offset from the inlet and outlet that enables the shaft cover support to surround the transition, thereby reducing the overall length of this section of the engine.« less

Nuclear component horizontal seismic restraint

DOEpatents

Snyder, Glenn J.

1988-01-01

A nuclear component horizontal seismic restraint. Small gaps limit horizontal displacement of components during a seismic occurrence and therefore reduce dynamic loadings on the free lower end. The reactor vessel and reactor guard vessel use thicker section roll-forged rings welded between the vessel straight shell sections and the bottom hemispherical head sections. The inside of the reactor guard vessel ring forging contains local vertical dovetail slots and upper ledge pockets to mount and retain field fitted and installed blocks. As an option, the horizontal displacement of the reactor vessel core support cone can be limited by including shop fitted/installed local blocks in opposing alignment with the reactor vessel forged ring. Beams embedded in the wall of the reactor building protrude into apertures in the thermal insulation shell adjacent the reactor guard vessel ring and have motion limit blocks attached thereto to provide to a predetermined clearance between the blocks and reactor guard vessel ring.

10 CFR 54.21 - Contents of application-technical information.

Code of Federal Regulations, 2013 CFR

2013-01-01

... delineated in § 54.4, identify and list those structures and components subject to an aging management review. Structures and components subject to an aging management review shall encompass those structures and... component identified in paragraph (a)(1) of this section, demonstrate that the effects of aging will be...

10 CFR 54.21 - Contents of application-technical information.

Code of Federal Regulations, 2012 CFR

2012-01-01

... delineated in § 54.4, identify and list those structures and components subject to an aging management review. Structures and components subject to an aging management review shall encompass those structures and... component identified in paragraph (a)(1) of this section, demonstrate that the effects of aging will be...

10 CFR 54.21 - Contents of application-technical information.

Code of Federal Regulations, 2014 CFR

2014-01-01

... delineated in § 54.4, identify and list those structures and components subject to an aging management review. Structures and components subject to an aging management review shall encompass those structures and... component identified in paragraph (a)(1) of this section, demonstrate that the effects of aging will be...

46 CFR 108.473 - Foam system components.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 4 2011-10-01 2011-10-01 false Foam system components. 108.473 Section 108.473 Shipping... EQUIPMENT Fire Extinguishing Systems Foam Extinguishing Systems § 108.473 Foam system components. (a) Each foam agent, each tank for a foam agent, each discharge outlet, each control, and each valve for the...

46 CFR 108.473 - Foam system components.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Foam system components. 108.473 Section 108.473 Shipping... EQUIPMENT Fire Extinguishing Systems Foam Extinguishing Systems § 108.473 Foam system components. (a) Each foam agent, each tank for a foam agent, each discharge outlet, each control, and each valve for the...

30 CFR 7.506 - Breathable air components.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Breathable air components. 7.506 Section 7.506... APPROVAL OF MINING PRODUCTS TESTING BY APPLICANT OR THIRD PARTY Refuge Alternatives § 7.506 Breathable air components. (a) Breathable air shall be supplied by compressed air cylinders, compressed breathable-oxygen...

30 CFR 7.506 - Breathable air components.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Breathable air components. 7.506 Section 7.506... APPROVAL OF MINING PRODUCTS TESTING BY APPLICANT OR THIRD PARTY Refuge Alternatives § 7.506 Breathable air components. (a) Breathable air shall be supplied by compressed air cylinders, compressed breathable-oxygen...

30 CFR 7.506 - Breathable air components.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Breathable air components. 7.506 Section 7.506... APPROVAL OF MINING PRODUCTS TESTING BY APPLICANT OR THIRD PARTY Refuge Alternatives § 7.506 Breathable air components. (a) Breathable air shall be supplied by compressed air cylinders, compressed breathable-oxygen...

78 FR 63243 - Certain Audiovisual Components and Products Containing the Same; Commission Determination To...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-10-23

... INTERNATIONAL TRADE COMMISSION [Investigation No. 337-TA-837] Certain Audiovisual Components and Products Containing the Same; Commission Determination To Review a Final Initial Determination Finding a... section 337 as to certain audiovisual components and products containing the same with respect to claims 1...

21 CFR 864.2360 - Mycoplasma detection media and components.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Mycoplasma detection media and components. 864.2360 Section 864.2360 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN... § 864.2360 Mycoplasma detection media and components. (a) Identification. Mycoplasma detection media and...

21 CFR 864.2360 - Mycoplasma detection media and components.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Mycoplasma detection media and components. 864.2360 Section 864.2360 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN... § 864.2360 Mycoplasma detection media and components. (a) Identification. Mycoplasma detection media and...

21 CFR 864.2360 - Mycoplasma detection media and components.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Mycoplasma detection media and components. 864.2360 Section 864.2360 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN... § 864.2360 Mycoplasma detection media and components. (a) Identification. Mycoplasma detection media and...

21 CFR 864.2360 - Mycoplasma detection media and components.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Mycoplasma detection media and components. 864.2360 Section 864.2360 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN... § 864.2360 Mycoplasma detection media and components. (a) Identification. Mycoplasma detection media and...

7 CFR 1126.53 - Announcement of class prices, component prices, and advanced pricing factors.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 9 2010-01-01 2009-01-01 true Announcement of class prices, component prices, and advanced pricing factors. 1126.53 Section 1126.53 Agriculture Regulations of the Department of Agriculture... class prices, component prices, and advanced pricing factors. See § 1000.53. ...

7 CFR 1030.53 - Announcement of class prices, component prices, and advanced pricing factors.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 9 2010-01-01 2009-01-01 true Announcement of class prices, component prices, and advanced pricing factors. 1030.53 Section 1030.53 Agriculture Regulations of the Department of Agriculture... of class prices, component prices, and advanced pricing factors. See § 1000.53. ...

7 CFR 1033.53 - Announcement of class prices, component prices, and advanced pricing factors.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 9 2010-01-01 2009-01-01 true Announcement of class prices, component prices, and advanced pricing factors. 1033.53 Section 1033.53 Agriculture Regulations of the Department of Agriculture... class prices, component prices, and advanced pricing factors. See § 1000.53. ...

7 CFR 1005.53 - Announcement of class prices, component prices, and advanced pricing factors.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 9 2010-01-01 2009-01-01 true Announcement of class prices, component prices, and advanced pricing factors. 1005.53 Section 1005.53 Agriculture Regulations of the Department of Agriculture... class prices, component prices, and advanced pricing factors. See § 1000.53. ...

7 CFR 1032.53 - Announcement of class prices, component prices, and advanced pricing factors.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 9 2010-01-01 2009-01-01 true Announcement of class prices, component prices, and advanced pricing factors. 1032.53 Section 1032.53 Agriculture Regulations of the Department of Agriculture... class prices, component prices, and advanced pricing factors. See § 1000.53. ...

7 CFR 1006.53 - Announcement of class prices, component prices, and advanced pricing factors.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 9 2010-01-01 2009-01-01 true Announcement of class prices, component prices, and advanced pricing factors. 1006.53 Section 1006.53 Agriculture Regulations of the Department of Agriculture... class prices, component prices, and advanced pricing factors. See § 1000.53. ...

7 CFR 1001.53 - Announcement of class prices, component prices, and advanced pricing factors.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 9 2010-01-01 2009-01-01 true Announcement of class prices, component prices, and advanced pricing factors. 1001.53 Section 1001.53 Agriculture Regulations of the Department of Agriculture... class prices, component prices, and advanced pricing factors. See § 1000.53. ...

7 CFR 1131.53 - Announcement of class prices, component prices, and advanced pricing factors.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 9 2010-01-01 2009-01-01 true Announcement of class prices, component prices, and advanced pricing factors. 1131.53 Section 1131.53 Agriculture Regulations of the Department of Agriculture... class prices, component prices, and advanced pricing factors. See § 1000.53. ...

7 CFR 1007.53 - Announcement of class prices, component prices, and advanced pricing factors.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 9 2010-01-01 2009-01-01 true Announcement of class prices, component prices, and advanced pricing factors. 1007.53 Section 1007.53 Agriculture Regulations of the Department of Agriculture... class prices, component prices, and advanced pricing factors. See § 1000.53. ...

23 CFR 500.204 - TMS components for highway traffic data.

Code of Federal Regulations, 2010 CFR

2010-04-01

... INFRASTRUCTURE MANAGEMENT MANAGEMENT AND MONITORING SYSTEMS Traffic Monitoring System § 500.204 TMS components for highway traffic data. (a) General. Each State's TMS, including those using alternative procedures... 23 Highways 1 2010-04-01 2010-04-01 false TMS components for highway traffic data. 500.204 Section...

49 CFR 172.802 - Components of a security plan.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 49 Transportation 2 2013-10-01 2013-10-01 false Components of a security plan. 172.802 Section 172... TABLE, SPECIAL PROVISIONS, HAZARDOUS MATERIALS COMMUNICATIONS, EMERGENCY RESPONSE INFORMATION, TRAINING REQUIREMENTS, AND SECURITY PLANS Safety and Security Plans § 172.802 Components of a security plan. (a) The...

49 CFR 172.802 - Components of a security plan.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 49 Transportation 2 2014-10-01 2014-10-01 false Components of a security plan. 172.802 Section 172... TABLE, SPECIAL PROVISIONS, HAZARDOUS MATERIALS COMMUNICATIONS, EMERGENCY RESPONSE INFORMATION, TRAINING REQUIREMENTS, AND SECURITY PLANS Safety and Security Plans § 172.802 Components of a security plan. (a) The...

49 CFR 172.802 - Components of a security plan.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 2 2011-10-01 2011-10-01 false Components of a security plan. 172.802 Section 172... TABLE, SPECIAL PROVISIONS, HAZARDOUS MATERIALS COMMUNICATIONS, EMERGENCY RESPONSE INFORMATION, TRAINING REQUIREMENTS, AND SECURITY PLANS Safety and Security Plans § 172.802 Components of a security plan. (a) The...

49 CFR 172.802 - Components of a security plan.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 49 Transportation 2 2012-10-01 2012-10-01 false Components of a security plan. 172.802 Section 172... TABLE, SPECIAL PROVISIONS, HAZARDOUS MATERIALS COMMUNICATIONS, EMERGENCY RESPONSE INFORMATION, TRAINING REQUIREMENTS, AND SECURITY PLANS Safety and Security Plans § 172.802 Components of a security plan. (a) The...

Multiple-source multiple-harmonic active vibration control of variable section cylindrical structures: A numerical study

NASA Astrophysics Data System (ADS)

Liu, Jinxin; Chen, Xuefeng; Gao, Jiawei; Zhang, Xingwu

2016-12-01

Air vehicles, space vehicles and underwater vehicles, the cabins of which can be viewed as variable section cylindrical structures, have multiple rotational vibration sources (e.g., engines, propellers, compressors and motors), making the spectrum of noise multiple-harmonic. The suppression of such noise has been a focus of interests in the field of active vibration control (AVC). In this paper, a multiple-source multiple-harmonic (MSMH) active vibration suppression algorithm with feed-forward structure is proposed based on reference amplitude rectification and conjugate gradient method (CGM). An AVC simulation scheme called finite element model in-loop simulation (FEMILS) is also proposed for rapid algorithm verification. Numerical studies of AVC are conducted on a variable section cylindrical structure based on the proposed MSMH algorithm and FEMILS scheme. It can be seen from the numerical studies that: (1) the proposed MSMH algorithm can individually suppress each component of the multiple-harmonic noise with an unified and improved convergence rate; (2) the FEMILS scheme is convenient and straightforward for multiple-source simulations with an acceptable loop time. Moreover, the simulations have similar procedure to real-life control and can be easily extended to physical model platform.

Taming axial dispersion in hydrodynamic chromatography columns through wall patterning

NASA Astrophysics Data System (ADS)

Adrover, Alessandra; Cerbelli, Stefano; Giona, Massimiliano

2018-04-01

A well-known limitation of hydrodynamic chromatography arises from the synergistic interaction between transverse diffusion and streamwise convection, which enhances axial dispersion through the Taylor-Aris mechanism. We show that a periodic sequence of slip/no-slip conditions at the channel walls (e.g., representing wall indentations hosting stable air pockets) can significantly reduce axial dispersion, thus enhancing separation performance. The theoretical/numerical analysis is based on a generalization of Brenner's macrotransport approach to solute transport, here modified to account for the finite-size of the suspended particles. The most effective dispersion-taming outcome is observed when the alternating sequence of slip/no-slip conditions yields non-vanishing cross-sectional flow components. The combination of these components with the hindering interaction between the channel boundaries and the finite-sized particles gives rise to a non-trivial solution of Brenner's problem on the unit periodic cell, where the cross-sectional particle number density departs from the spatially homogeneous condition. In turn, this effect impacts upon the solution of the so-called b-field defining the large-scale dispersion tensor, with an overall decremental effect on the axial dispersion coefficient and on the Height Equivalent of a Theoretical Plate.

Definition and means of maintaining the criticality detectors and alarms portion of the PFP safety envelope

DOE Office of Scientific and Technical Information (OSTI.GOV)

White, W.F.

The purpose of this document is to provide the definition and means of maintaining the Safety Envelope (SE) related to the Criticality Alarm System (CAS). This document provides amplification of the Limiting Condition for Operation (LCO) described in the Plutonium Finishing Plant (PFP) Operational Safety Requirements (OSR), WHC-SD-CP-OSR-010, Rev. 0, 1994, Section 3.1.2, Criticality Detectors and Alarms. This document, with its appendices, provides the following: (1) System functional requirements for determining system operability (Section 3); (2) A list of annotated system block diagrams which indicate the safety envelope boundaries (Appendix C); (3) A list of the Safety Class 1 andmore » 2 Safety Envelope (SC-1/2 SE) equipment for input into the Master Component Index (Appendix B); (4) Functional requirements for individual SC-1/2 SE components, including appropriate setpoints and process parameters (Section 6 and Appendix A); (5) A list of the operational, maintenance and surveillance procedures necessary to operate and maintain the SC-1/2 SE components as required by the LCO (Section 6 and Appendix A).« less

Metabolic syndrome correlates poorly with cognitive performance in stroke-free community-dwelling older adults: a population-based, cross-sectional study in rural Ecuador.

PubMed

Del Brutto, Oscar H; Mera, Robertino M; Zambrano, Mauricio

2016-04-01

Studies investigating a possible correlation between metabolic syndrome and cognitive decline have been inconsistent. To determine whether metabolic syndrome or each of its components correlate with cognitive performance in community-dwelling older adults in rural Ecuador. Stroke-free Atahualpa residents aged ≥60 years were identified during a door-to-door survey. Metabolic syndrome was defined according to the International Diabetes Federation criteria. Cognition was evaluated by the use of the Montreal Cognitive Assessment (MoCA). Multivariate logistic regression models estimated the association between metabolic syndrome and each of its components with cognitive performance. A total of 212 persons (mean age: 69.2 ± 7.2 years, 64 % women) were enrolled. Of these, 120 (57 %) had metabolic syndrome. Mean scores in the MoCA were 18.2 ± 4.6 for persons with and 19 ± 4.7 for those without metabolic syndrome. In fully adjusted logistic models, MoCA scores were not associated with metabolic syndrome (p = 0.101). After testing individual components of metabolic syndrome with the MoCA score, we found that only hypertriglyceridemia was independently associated with the MoCA score (p = 0.009). This population-based study showed a poor correlation of metabolic syndrome with cognitive performance after adjusting for relevant confounders. Of the individual components of metabolic syndrome, only hypertriglyceridemia correlated with worse cognitive performance.

78 FR 13911 - Proposed Revision to Design of Structures, Components, Equipment and Systems

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-01

... Analysis Reports for Nuclear Power Plants: LWR Edition,'' Section 3.7.1, ``Seismic Design Parameters,'' Section 3.7.2, ``Seismic System Analysis,'' Section 3.7.3, ``Seismic Subsystem Analysis,'' Section 3.8.1... and analysis issues, (2) updates to review interfaces to improve the efficiency and consistency of...

75 FR 33818 - Nationwide Limited Public Interest Waiver of Section 1605 (Buy American Requirement) of American...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-15

... Waiver of Section 1605 (Buy American Requirement) of American Recovery and Reinvestment Act of 2009 (ARRA... of the American Recovery and Reinvestment Act of 2009 (ARRA) Section 1605 under the authority of Section 1605(b)(1) (public interest waiver) for de minimis incidental components of sanitation facilities...

Film Cooled Recession of SiC/SiC Ceramic Matrix Composites: Test Development, CFD Modeling and Experimental Observations

NASA Technical Reports Server (NTRS)

Zhu, Dongming; Sakowski, Barbara A.; Fisher, Caleb

2014-01-01

SiCSiC ceramic matrix composites (CMCs) systems will play a crucial role in next generation turbine engines for hot-section component applications because of their ability to significantly increase engine operating temperatures, reduce engine weight and cooling requirements. However, the environmental stability of Si-based ceramics in high pressure, high velocity turbine engine combustion environment is of major concern. The water vapor containing combustion gas leads to accelerated oxidation and corrosion of the SiC based ceramics due to the water vapor reactions with silica (SiO2) scales forming non-protective volatile hydroxide species, resulting in recession of the ceramic components. Although environmental barrier coatings are being developed to help protect the CMC components, there is a need to better understand the fundamental recession behavior of in more realistic cooled engine component environments.In this paper, we describe a comprehensive film cooled high pressure burner rig based testing approach, by using standardized film cooled SiCSiC disc test specimen configurations. The SiCSiC specimens were designed for implementing the burner rig testing in turbine engine relevant combustion environments, obtaining generic film cooled recession rate data under the combustion water vapor conditions, and helping developing the Computational Fluid Dynamics (CFD) film cooled models and performing model validation. Factors affecting the film cooled recession such as temperature, water vapor concentration, combustion gas velocity, and pressure are particularly investigated and modeled, and compared with impingement cooling only recession data in similar combustion flow environments. The experimental and modeling work will help predict the SiCSiC CMC recession behavior, and developing durable CMC systems in complex turbine engine operating conditions.

Organizational home care models across Europe: A cross sectional study.

PubMed

Van Eenoo, Liza; van der Roest, Henriëtte; Onder, Graziano; Finne-Soveri, Harriet; Garms-Homolova, Vjenka; Jonsson, Palmi V; Draisma, Stasja; van Hout, Hein; Declercq, Anja

2018-01-01

Decision makers are searching for models to redesign home care and to organize health care in a more sustainable way. The aim of this study is to identify and characterize home care models within and across European countries by means of structural characteristics and care processes at the policy and the organization level. At the policy level, variables that reflected variation in health care policy were included based on a literature review on the home care policy for older persons in six European countries: Belgium, Finland, Germany, Iceland, Italy, and the Netherlands. At the organizational level, data on the structural characteristics and the care processes were collected from 36 home care organizations by means of a survey. Data were collected between 2013 and 2015 during the IBenC project. An observational, cross sectional, quantitative design was used. The analyses consisted of a principal component analysis followed by a hierarchical cluster analysis. Fifteen variables at the organizational level, spread across three components, explained 75.4% of the total variance. The three components made it possible to distribute home care organizations into six care models that differ on the level of patient-centered care delivery, the availability of specialized care professionals, and the level of monitoring care performance. Policy level variables did not contribute to distinguishing between home care models. Six home care models were identified and characterized. These models can be used to describe best practices. Copyright © 2017 Elsevier Ltd. All rights reserved.

Sleep bruxism, awake bruxism and sleep quality among Brazilian dental students: a cross-sectional study.

PubMed

Serra-Negra, Júnia Maria; Scarpelli, Ana Carolina; Tirsa-Costa, Débora; Guimarães, Flávia Helena; Pordeus, Isabela Almeida; Paiva, Saul Martins

2014-01-01

The aim of the study was to evaluate the association of sleep bruxism, awake bruxism and sleep quality among dental students of the Federal University of Minas Gerais, Belo Horizonte, Brazil. A cross-sectional study was performed including 183 Brazilian dental students aged from 17 to 46 years old. The complete course curriculum consists of 9 semesters. Students enrolled in the first semester, the middle semester and the final semester of the course participated in the survey. The PSQI-BR (the Brazilian version of the Pittsburgh Sleep Questionnaire Index) was used for data collection. The PSQI-BR was distributed during lecture classes. Sleep bruxism and awake bruxism diagnosis was based on self-reported data. Descriptive analysis, Kruskal-Wallis, Mann-Whitney and Poisson regression with robust estimator were the statistical tests used. Sleep bruxism prevalence was 21.5% and awake bruxism prevalence was 36.5%. Sleep duration components were associated with sleep bruxism (PR=1.540; 95% CI: 1.00-2.37) and awake bruxism (PR=1.344; 95% CI: 1,008-1,790). There was an association between awake bruxism and habitual sleep efficiency component (PR=1.323; 95% CI: 1.03-1.70). Sleep disturbance component and awake bruxism were associated (PR=1.533; 95% CI: 1.03-2.27). Poor sleep quality was an important factor among dental students, who reported sleep bruxism as well as among those who presented awake bruxism.

Electrochemical Enzyme Biosensors Revisited: Old Solutions for New Problems.

PubMed

Monteiro, Tiago; Almeida, Maria Gabriela

2018-05-14

Worldwide legislation is driving the development of novel and highly efficient analytical tools for assessing the composition of every material that interacts with Consumers or Nature. The biosensor technology is one of the most active R&D domains of Analytical Sciences focused on the challenge of taking analytical chemistry to the field. Electrochemical biosensors based on redox enzymes, in particular, are highly appealing due to their usual quick response, high selectivity and sensitivity, low cost and portable dimensions. This review paper aims to provide an overview of the most important advances made in the field since the proposal of the first biosensor, the well-known hand-held glucose meter. The first section addresses the current needs and challenges for novel analytical tools, followed by a brief description of the different components and configurations of biosensing devices, and the fundamentals of enzyme kinetics and amperometry. The following sections emphasize on enzyme-based amperometric biosensors and the different stages of their development.

Anti-Stokes effect CCD camera and SLD based optical coherence tomography for full-field imaging in the 1550nm region

NASA Astrophysics Data System (ADS)

Kredzinski, Lukasz; Connelly, Michael J.

2012-06-01

Full-field Optical coherence tomography is an en-face interferometric imaging technology capable of carrying out high resolution cross-sectional imaging of the internal microstructure of an examined specimen in a non-invasive manner. The presented system is based on competitively priced optical components available at the main optical communications band located in the 1550 nm region. It consists of a superluminescent diode and an anti-stokes imaging device. The single mode fibre coupled SLD was connected to a multi-mode fibre inserted into a mode scrambler to obtain spatially incoherent illumination, suitable for OCT wide-field modality in terms of crosstalk suppression and image enhancement. This relatively inexpensive system with moderate resolution of approximately 24um x 12um (axial x lateral) was constructed to perform a 3D cross sectional imaging of a human tooth. To our knowledge this is the first 1550 nm full-field OCT system reported.

32 CFR 21.320 - Are there areas in which DoD Components must establish policies and procedures to implement the...

Code of Federal Regulations, 2012 CFR

2012-07-01

... under awards, if the DoD Component makes any awards to institutions of higher education or to other... establish policies and procedures to implement the DoDGARs? 21.320 Section 21.320 National Defense... Components must establish policies and procedures to implement the DoDGARs? Yes, Heads of DoD Components or...

32 CFR 21.320 - Are there areas in which DoD Components must establish policies and procedures to implement the...

Code of Federal Regulations, 2011 CFR

2011-07-01

... under awards, if the DoD Component makes any awards to institutions of higher education or to other... establish policies and procedures to implement the DoDGARs? 21.320 Section 21.320 National Defense... Components must establish policies and procedures to implement the DoDGARs? Yes, Heads of DoD Components or...

32 CFR 21.320 - Are there areas in which DoD Components must establish policies and procedures to implement the...

Code of Federal Regulations, 2014 CFR

2014-07-01

... under awards, if the DoD Component makes any awards to institutions of higher education or to other... establish policies and procedures to implement the DoDGARs? 21.320 Section 21.320 National Defense... Components must establish policies and procedures to implement the DoDGARs? Yes, Heads of DoD Components or...

32 CFR 21.320 - Are there areas in which DoD Components must establish policies and procedures to implement the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... under awards, if the DoD Component makes any awards to institutions of higher education or to other... establish policies and procedures to implement the DoDGARs? 21.320 Section 21.320 National Defense... Components must establish policies and procedures to implement the DoDGARs? Yes, Heads of DoD Components or...

32 CFR 21.320 - Are there areas in which DoD Components must establish policies and procedures to implement the...

Code of Federal Regulations, 2013 CFR

2013-07-01

... under awards, if the DoD Component makes any awards to institutions of higher education or to other... establish policies and procedures to implement the DoDGARs? 21.320 Section 21.320 National Defense... Components must establish policies and procedures to implement the DoDGARs? Yes, Heads of DoD Components or...

19 CFR 10.26 - Articles assembled or processed in a beneficiary country in whole of U.S. components or...

Code of Federal Regulations, 2010 CFR

2010-04-01

... textile components cut to shape in the United States. 10.26 Section 10.26 Customs Duties U.S. CUSTOMS AND... ingredients; articles assembled in a beneficiary country from textile components cut to shape in the United... assembled in a beneficiary country in whole of textile components cut to shape (but not to length, width, or...

NASA Tech Briefs, October 1998. Volume 22, No. 10

NASA Technical Reports Server (NTRS)

1998-01-01

Topics include: special coverage sections on sensors/imaging and mechanical technology, and sections on electronic components and circuits, electronic systems, software, materials, machinery/automation, manufacturing/fabrication, physical sciences, information sciences, book and reports, and a special section of Photonics Tech Briefs.

In-vivo segmentation and quantification of coronary lesions by optical coherence tomography images for a lesion type definition and stenosis grading.

PubMed

Celi, Simona; Berti, Sergio

2014-10-01

Optical coherence tomography (OCT) is a catheter-based medical imaging technique that produces cross-sectional images of blood vessels. This technique is particularly useful for studying coronary atherosclerosis. In this paper, we present a new framework that allows a segmentation and quantification of OCT images of coronary arteries to define the plaque type and stenosis grading. These analyses are usually carried out on-line on the OCT-workstation where measuring is mainly operator-dependent and mouse-based. The aim of this program is to simplify and improve the processing of OCT images for morphometric investigations and to present a fast procedure to obtain 3D geometrical models that can also be used for external purposes such as for finite element simulations. The main phases of our toolbox are the lumen segmentation and the identification of the main tissues in the artery wall. We validated the proposed method with identification and segmentation manually performed by expert OCT readers. The method was evaluated on ten datasets from clinical routine and the validation was performed on 210 images randomly extracted from the pullbacks. Our results show that automated segmentation of the vessel and of the tissue components are possible off-line with a precision that is comparable to manual segmentation for the tissue component and to the proprietary-OCT-console for the lumen segmentation. Several OCT sections have been processed to provide clinical outcome. Copyright © 2014 Elsevier B.V. All rights reserved.

Constitutive modeling for isotropic materials

NASA Technical Reports Server (NTRS)

Chan, K. S.; Lindholm, U. S.; Bodner, S. R.

1988-01-01

The third and fourth years of a 4-year research program, part of the NASA HOST Program, are described. The program goals were: (1) to develop and validate unified constitutive models for isotropic materials, and (2) to demonstrate their usefulness for structural analysis of hot section components of gas turbine engines. The unified models selected for development and evaluation were those of Bodner-Partom and of Walker. The unified approach for elastic-viscoplastic constitutive equations is a viable method for representing and predicting material response characteristics in the range where strain rate and temperature dependent inelastic deformations are experienced. This conclusion is reached by extensive comparison of model calculations against the experimental results of a test program of two high temperature Ni-base alloys, B1900+Hf and Mar-M247, over a wide temperature range for a variety of deformation and thermal histories including uniaxial, multiaxial, and thermomechanical loading paths. The applicability of the Bodner-Partom and the Walker models for structural applications has been demonstrated by implementing these models into the MARC finite element code and by performing a number of analyses including thermomechanical histories on components of hot sections of gas turbine engines and benchmark notch tensile specimens. The results of the 4-year program have been published in four annual reports. The results of the base program are summarized in this report. The tasks covered include: (1) development of material test procedures, (2) thermal history effects, and (3) verification of the constitutive model for an alternative material.

Development of an integrated BEM approach for hot fluid structure interaction: BEST-FSI: Boundary Element Solution Technique for Fluid Structure Interaction

NASA Technical Reports Server (NTRS)

Dargush, G. F.; Banerjee, P. K.; Shi, Y.

1992-01-01

As part of the continuing effort at NASA LeRC to improve both the durability and reliability of hot section Earth-to-orbit engine components, significant enhancements must be made in existing finite element and finite difference methods, and advanced techniques, such as the boundary element method (BEM), must be explored. The BEM was chosen as the basic analysis tool because the critical variables (temperature, flux, displacement, and traction) can be very precisely determined with a boundary-based discretization scheme. Additionally, model preparation is considerably simplified compared to the more familiar domain-based methods. Furthermore, the hyperbolic character of high speed flow is captured through the use of an analytical fundamental solution, eliminating the dependence of the solution on the discretization pattern. The price that must be paid in order to realize these advantages is that any BEM formulation requires a considerable amount of analytical work, which is typically absent in the other numerical methods. All of the research accomplishments of a multi-year program aimed toward the development of a boundary element formulation for the study of hot fluid-structure interaction in Earth-to-orbit engine hot section components are detailed. Most of the effort was directed toward the examination of fluid flow, since BEM's for fluids are at a much less developed state. However, significant strides were made, not only in the analysis of thermoviscous fluids, but also in the solution of the fluid-structure interaction problem.

Microgravity Manufacturing Via Fused Deposition

NASA Technical Reports Server (NTRS)

Cooper, K. G.; Griffin, M. R.

2003-01-01

Manufacturing polymer hardware during space flight is currently outside the state of the art. A process called fused deposition modeling (FDM) can make this approach a reality by producing net-shaped components of polymer materials directly from a CAE model. FDM is a rapid prototyping process developed by Stratasys, Inc.. which deposits a fine line of semi-molten polymer onto a substrate while moving via computer control to form the cross-sectional shape of the part it is building. The build platen is then lowered and the process is repeated, building a component directly layer by layer. This method enables direct net-shaped production of polymer components directly from a computer file. The layered manufacturing process allows for the manufacture of complex shapes and internal cavities otherwise impossible to machine. This task demonstrated the benefits of the FDM technique to quickly and inexpensively produce replacement components or repair broken hardware in a Space Shuttle or Space Station environment. The intent of the task was to develop and fabricate an FDM system that was lightweight, compact, and required minimum power consumption to fabricate ABS plastic hardware in microgravity. The final product of the shortened task turned out to be a ground-based breadboard device, demonstrating miniaturization capability of the system.

Environmental Stability and Oxidation Behavior of HfO2-Si and YbGd(O) Based Environmental Barrier Coating Systems for SiCSiC Ceramic Matrix Composites

NASA Technical Reports Server (NTRS)

Zhu, Dongming; Farmer, Serene; McCue, Terry R.; Harder, Bryan; Hurst, Janet B.

2017-01-01

Ceramic environmental barrier coatings (EBC) and SiCSiC ceramic matrix composites (CMCs) will play a crucial role in future aircraft propulsion systems because of their ability to significantly increase engine operating temperatures, improve component durability, reduce engine weight and cooling requirements. Advanced EBC systems for SiCSiC CMC turbine and combustor hot section components are currently being developed to meet future turbine engine emission and performance goals. One of the significant material development challenges for the high temperature CMC components is to develop prime-reliant, environmental durable environmental barrier coating systems. In this paper, the durability and performance of advanced Electron Beam-Physical Vapor Deposition (EB-PVD) NASA HfO2-Si and YbGdSi(O) EBC bond coat top coat systems for SiCSiC CMC have been summarized. The high temperature thermomechanical creep, fatigue and oxidation resistance have been investigated in the laboratory simulated high-heat-flux environmental test conditions. The advanced NASA EBC systems showed promise to achieve 1500C temperature capability, helping enable next generation turbine engines with significantly improved engine component temperature capability and durability.

Gaseous insulators for high voltage electrical equipment

DOEpatents

Christophorou, Loucas G.; James, David R.; Pace, Marshall O.; Pai, Robert Y.

1979-01-01

Gaseous insulators comprise compounds having high attachment cross sections for electrons having energies in the 0-1.3 electron volt range. Multi-component gaseous insulators comprise compounds and mixtures having overall high electron attachment cross sections in the 0-1.3 electron volt range and moderating gases having high cross sections for inelastic interactions with electrons of energies 1-4 electron volts. Suitable electron attachment components include hexafluorobutyne, perfluorobutene-2, perfluorocyclobutane, perfluorodimethylcyclobutane, perfluorocyclohexene, perfluoromethylcyclohexane, hexafluorobutadiene, perfluoroheptene-1 and hexafluoroazomethane. Suitable moderating gases include N.sub.2, CO, CO.sub.2 and H.sub.2. The gaseous insulating mixture can also contain SF.sub.6, perfluoropropane and perfluorobenzene.

Gaseous insulators for high voltage electrical equipment

DOEpatents

Christophorou, Loucas G.; James, David R.; Pace, Marshall O.; Pai, Robert Y.

1981-01-01

Gaseous insulators comprise compounds having high attachment cross sections for electrons having energies in the 0-1.3 electron volt range. Multi-component gaseous insulators comprise compounds and mixtures having overall high electron attachment cross sections in the 0-1.3 electron volt range and moderating gases having high cross sections for inelastic interactions with electrons of energies 1-4 electron volts. Suitable electron attachment components include hexafluorobutyne, perfluorobutene-2, perfluorocyclobutane, perfluorodimethylcyclobutane, perfluorocyclohexene, perfluoromethylcyclohexane, hexafluorobutadiene, perfluoroheptene-1 and hexafluoroazomethane. Suitable moderating gases include N.sub.2, CO, CO.sub.2 and H.sub.2. The gaseous insulating mixture can also contain SF.sub.6, perfluoropropane and perfluorobenzene.

Fine needle aspiration in the diagnosis and classification of hepatoblastoma: Analysis of 21 New Cases.

PubMed

Vlajnic, Tatjana; Brisse, Hervé J; Aerts, Isabelle; Fréneaux, Paul; Cellier, Cécile; Fabre, Monique; Klijanienko, Jerzy

2017-02-01

Diagnosis of hepatoblastoma (HBL) is based on characteristic clinical and radiological presentation, young age and marked elevation of serum α-fetoprotein (aFP). Fine needle aspiration (FNA) technique is successfully used in the diagnosis of hepatoblastoma. To evaluate the value of FNA in the diagnosis and subtyping of HBL, we report our experience correlated to histological sections (core needle biopsy, CNB). From 1991 to 2015, 21 cases from 20 patients were cytologically diagnosed as HBL. The patients were 15 males and 5 females, mean age being 3 years, and median age being 2 years and 4 months. Serum aFP levels ranged from negative to 1,285,000 ng/ml. We defined cytological criteria to diagnose fetal, embryonal, mesenchymal, and small cell undifferentiated components. The accurate cytological diagnosis of HBL was made in all cases; 8 cases exhibited a single component and 13 cases exhibited two or more components. Fetal and embryonal components were seen in 18 and 13 cases, respectively, and small cell undifferentiated component was seen in one case. Mesenchymal component was seen in 12 cases. Comparing cytology and histology, identical components were identified on both, FNA and CNB in 14 cases. When analyzing only the presence of epithelial components, 17 cases were concordant in both techniques. FNA allows to accurately diagnose HBL and recognize its histological subtypes. On the basis of high concordance between cytological and histological diagnosis, FNA is validated as an alternative diagnostic method to CNB. Diagn. Cytopathol. 2017;45:91-100. © 2016 Wiley Periodicals, Inc. © 2016 Wiley Periodicals, Inc.

Thermal and Environmental Barrier Coating Development for Advanced Propulsion Engine Systems

NASA Technical Reports Server (NTRS)

Zhu, Dongming; Miller, Robert A.; Fox, Dennis S.

2008-01-01

Ceramic thermal and environmental barrier coatings (TEBCs) are used in gas turbine engines to protect engine hot-section components in the harsh combustion environments, and extend component lifetimes. Advanced TEBCs that have significantly lower thermal conductivity, better thermal stability and higher toughness than current coatings will be beneficial for future low emission and high performance propulsion engine systems. In this paper, ceramic coating design and testing considerations will be described for turbine engine high temperature and high-heat-flux applications. Thermal barrier coatings for metallic turbine airfoils and thermal/environmental barrier coatings for SiC/SiC ceramic matrix composite (CMC) components for future supersonic aircraft propulsion engines will be emphasized. Further coating capability and durability improvements for the engine hot-section component applications can be expected by utilizing advanced modeling and design tools.

21 CFR 111.120 - What quality control operations are required for components, packaging, and labels before use in...

Code of Federal Regulations, 2013 CFR

2013-04-01

... components, packaging, and labels before use in the manufacture of a dietary supplement? 111.120 Section 111..., OR HOLDING OPERATIONS FOR DIETARY SUPPLEMENTS Production and Process Control System: Requirements for... labels before use in the manufacture of a dietary supplement? Quality control operations for components...

21 CFR 111.120 - What quality control operations are required for components, packaging, and labels before use in...

Code of Federal Regulations, 2014 CFR

2014-04-01

... components, packaging, and labels before use in the manufacture of a dietary supplement? 111.120 Section 111..., OR HOLDING OPERATIONS FOR DIETARY SUPPLEMENTS Production and Process Control System: Requirements for... labels before use in the manufacture of a dietary supplement? Quality control operations for components...

21 CFR 111.120 - What quality control operations are required for components, packaging, and labels before use in...

Code of Federal Regulations, 2012 CFR

2012-04-01

... components, packaging, and labels before use in the manufacture of a dietary supplement? 111.120 Section 111..., OR HOLDING OPERATIONS FOR DIETARY SUPPLEMENTS Production and Process Control System: Requirements for... labels before use in the manufacture of a dietary supplement? Quality control operations for components...

21 CFR 111.120 - What quality control operations are required for components, packaging, and labels before use in...

Code of Federal Regulations, 2011 CFR

2011-04-01

... components, packaging, and labels before use in the manufacture of a dietary supplement? 111.120 Section 111..., OR HOLDING OPERATIONS FOR DIETARY SUPPLEMENTS Production and Process Control System: Requirements for... labels before use in the manufacture of a dietary supplement? Quality control operations for components...

30 CFR 75.1508 - Training and records for examination, maintenance and repair of refuge alternatives and components.

Code of Federal Regulations, 2010 CFR

2010-07-01

... repair, the person conducting the maintenance or repair shall make a record of all corrective action..., maintenance and repair of refuge alternatives and components. 75.1508 Section 75.1508 Mineral Resources MINE..., maintenance and repair of refuge alternatives and components. (a) Persons examining, maintaining, or repairing...

32 CFR 21.650 - DoD Components.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 32 National Defense 1 2010-07-01 2010-07-01 false DoD Components. 21.650 Section 21.650 National Defense Department of Defense OFFICE OF THE SECRETARY OF DEFENSE DoD GRANT AND AGREEMENT REGULATIONS DoD GRANTS AND AGREEMENTS-GENERAL MATTERS Definitions § 21.650 DoD Components. The Office of the Secretary of...

32 CFR 21.650 - DoD Components.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 32 National Defense 1 2011-07-01 2011-07-01 false DoD Components. 21.650 Section 21.650 National Defense Department of Defense OFFICE OF THE SECRETARY OF DEFENSE DoD GRANT AND AGREEMENT REGULATIONS DoD GRANTS AND AGREEMENTS-GENERAL MATTERS Definitions § 21.650 DoD Components. The Office of the Secretary of...

32 CFR 21.650 - DoD Components.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 32 National Defense 1 2014-07-01 2014-07-01 false DoD Components. 21.650 Section 21.650 National Defense Department of Defense OFFICE OF THE SECRETARY OF DEFENSE DoD GRANT AND AGREEMENT REGULATIONS DoD GRANTS AND AGREEMENTS-GENERAL MATTERS Definitions § 21.650 DoD Components. The Office of the Secretary of...

32 CFR 21.650 - DoD Components.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 32 National Defense 1 2012-07-01 2012-07-01 false DoD Components. 21.650 Section 21.650 National Defense Department of Defense OFFICE OF THE SECRETARY OF DEFENSE DoD GRANT AND AGREEMENT REGULATIONS DoD GRANTS AND AGREEMENTS-GENERAL MATTERS Definitions § 21.650 DoD Components. The Office of the Secretary of...

32 CFR 21.650 - DoD Components.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 32 National Defense 1 2013-07-01 2013-07-01 false DoD Components. 21.650 Section 21.650 National Defense Department of Defense OFFICE OF THE SECRETARY OF DEFENSE DoD GRANT AND AGREEMENT REGULATIONS DoD GRANTS AND AGREEMENTS-GENERAL MATTERS Definitions § 21.650 DoD Components. The Office of the Secretary of...

21 CFR 181.26 - Drying oils as components of finished resins.

Code of Federal Regulations, 2011 CFR

2011-04-01

... classified as drying oils, when migrating from food-packaging material (as components of finished resins... 21 Food and Drugs 3 2011-04-01 2011-04-01 false Drying oils as components of finished resins. 181.26 Section 181.26 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN...

21 CFR 181.26 - Drying oils as components of finished resins.

Code of Federal Regulations, 2010 CFR

2010-04-01

... classified as drying oils, when migrating from food-packaging material (as components of finished resins... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Drying oils as components of finished resins. 181.26 Section 181.26 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN...

21 CFR 111.120 - What quality control operations are required for components, packaging, and labels before use in...

Code of Federal Regulations, 2010 CFR

2010-04-01

... components, packaging, and labels before use in the manufacture of a dietary supplement? 111.120 Section 111..., OR HOLDING OPERATIONS FOR DIETARY SUPPLEMENTS Production and Process Control System: Requirements for... labels before use in the manufacture of a dietary supplement? Quality control operations for components...

An Introductory Idea for Teaching Two-Component Phase Diagrams

ERIC Educational Resources Information Center

Peckham, Gavin D.; McNaught, Ian J.

2011-01-01

The teaching of two-component phase diagrams has attracted little attention in this "Journal," and it is hoped that this article will make a useful contribution. Current physical chemistry textbooks describe two-component phase diagrams adequately, but do so in a piecemeal fashion one section at a time; first solid-liquid equilibria, then…

7 CFR 1124.53 - Announcement of class prices, component prices, and advanced pricing factors.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 9 2010-01-01 2009-01-01 true Announcement of class prices, component prices, and advanced pricing factors. 1124.53 Section 1124.53 Agriculture Regulations of the Department of Agriculture... Announcement of class prices, component prices, and advanced pricing factors. See § 1000.53. ...

44 CFR 354.5 - Description of site-specific, plume pathway EPZ biennial exercise-related component services and...

Code of Federal Regulations, 2012 CFR

2012-10-01

..., plume pathway EPZ biennial exercise-related component services and other services. 354.5 Section 354.5... Description of site-specific, plume pathway EPZ biennial exercise-related component services and other... will assess fees on licensees include the following: (a) Site-specific, plume pathway EPZ biennial...

14 CFR 121.277 - Protection of other airplane components against fire.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false Protection of other airplane components....277 Protection of other airplane components against fire. (a) Except as provided in paragraph (b) of this section, all airplane surfaces aft of the nacelles in the area of one nacelle diameter on both...

14 CFR 121.277 - Protection of other airplane components against fire.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 3 2012-01-01 2012-01-01 false Protection of other airplane components....277 Protection of other airplane components against fire. (a) Except as provided in paragraph (b) of this section, all airplane surfaces aft of the nacelles in the area of one nacelle diameter on both...

14 CFR 121.277 - Protection of other airplane components against fire.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 3 2011-01-01 2011-01-01 false Protection of other airplane components....277 Protection of other airplane components against fire. (a) Except as provided in paragraph (b) of this section, all airplane surfaces aft of the nacelles in the area of one nacelle diameter on both...

14 CFR 121.277 - Protection of other airplane components against fire.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 3 2014-01-01 2014-01-01 false Protection of other airplane components....277 Protection of other airplane components against fire. (a) Except as provided in paragraph (b) of this section, all airplane surfaces aft of the nacelles in the area of one nacelle diameter on both...

20 CFR 228.50 - Tier II annuity component widow(er), child, or parent.

Code of Federal Regulations, 2010 CFR

2010-04-01

..., or parent. 228.50 Section 228.50 Employees' Benefits RAILROAD RETIREMENT BOARD REGULATIONS UNDER THE... annuity component widow(er), child, or parent. (a) General. The tier II annuity component is an additional amount payable to a widow(er), disabled widow(er), child, or parent, but not to a surviving divorced...

77 FR 23751 - Certain Food Waste Disposers and Components and Packaging Thereof; Institution of Investigation...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-20

... INTERNATIONAL TRADE COMMISSION [Inv. No. 337-TA-838] Certain Food Waste Disposers and Components... States after importation of certain food waste disposers and components and packaging thereof by reason... an industry in the United States exists as required by subsections (a)(1)(A) and (a)(2) of section...

30 CFR 7.508 - Harmful gas removal components.

Code of Federal Regulations, 2012 CFR

2012-07-01

... chemical used for removal of harmful gas shall be— (1) Contained such that when stored or used it cannot... for disposal of used chemical. (c) Each harmful gas removal component shall be tested to determine its... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Harmful gas removal components. 7.508 Section 7...

30 CFR 7.508 - Harmful gas removal components.

Code of Federal Regulations, 2013 CFR

2013-07-01

... chemical used for removal of harmful gas shall be— (1) Contained such that when stored or used it cannot... for disposal of used chemical. (c) Each harmful gas removal component shall be tested to determine its... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Harmful gas removal components. 7.508 Section 7...

30 CFR 7.508 - Harmful gas removal components.

Code of Federal Regulations, 2014 CFR

2014-07-01

... chemical used for removal of harmful gas shall be— (1) Contained such that when stored or used it cannot... for disposal of used chemical. (c) Each harmful gas removal component shall be tested to determine its... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Harmful gas removal components. 7.508 Section 7...

21 CFR 181.26 - Drying oils as components of finished resins.

Code of Federal Regulations, 2013 CFR

2013-04-01

... classified as drying oils, when migrating from food-packaging material (as components of finished resins... 21 Food and Drugs 3 2013-04-01 2013-04-01 false Drying oils as components of finished resins. 181.26 Section 181.26 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN...

21 CFR 181.26 - Drying oils as components of finished resins.

Code of Federal Regulations, 2014 CFR

2014-04-01

... food-packaging material (as components of finished resins) shall include: Chinawood oil (tung oil... 21 Food and Drugs 3 2014-04-01 2014-04-01 false Drying oils as components of finished resins. 181.26 Section 181.26 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN...

21 CFR 181.26 - Drying oils as components of finished resins.

Code of Federal Regulations, 2012 CFR

2012-04-01

... classified as drying oils, when migrating from food-packaging material (as components of finished resins... 21 Food and Drugs 3 2012-04-01 2012-04-01 false Drying oils as components of finished resins. 181.26 Section 181.26 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN...

14 CFR 121.277 - Protection of other airplane components against fire.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Protection of other airplane components....277 Protection of other airplane components against fire. (a) Except as provided in paragraph (b) of this section, all airplane surfaces aft of the nacelles in the area of one nacelle diameter on both...

14 CFR 1203a.105 - Implementation by field and component installations.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 5 2011-01-01 2010-01-01 true Implementation by field and component installations. 1203a.105 Section 1203a.105 Aeronautics and Space NATIONAL AERONAUTICS AND SPACE ADMINISTRATION NASA SECURITY AREAS § 1203a.105 Implementation by field and component installations. If a Director of a...

Crash energy absorption of two-segment crash box with holes under frontal load

DOE Office of Scientific and Technical Information (OSTI.GOV)

Choiron, Moch Agus, E-mail: agus-choiron@ub.ac.id; Sudjito,; Hidayati, Nafisah Arina

Crash box is one of the passive safety components which designed as an impact energy absorber during collision. Crash box designs have been developed in order to obtain the optimum crashworthiness performance. Circular cross section was first investigated with one segment design, it rather influenced by its length which is being sensitive to the buckling occurrence. In this study, the two-segment crash box design with additional holes is investigated and deformation behavior and crash energy absorption are observed. The crash box modelling is performed by finite element analysis. The crash test components were impactor, crash box, and fixed rigid base.more » Impactor and the fixed base material are modelled as a rigid, and crash box material as bilinear isotropic hardening. Crash box length of 100 mm and frontal crash velocity of 16 km/jam are selected. Crash box material of Aluminum Alloy is used. Based on simulation results, it can be shown that holes configuration with 2 holes and ¾ length locations have the largest crash energy absorption. This condition associated with deformation pattern, this crash box model produces axisymmetric mode than other models.« less

Long regional magnetotelluric profile crossing geotectonic structures of central Poland

NASA Astrophysics Data System (ADS)

Stefaniuk, M.; Pokorski, J.; Wojdyla, M.

2009-04-01

Introduction The magnetotelluric survey was made along a regional profile, which runs across Poland from south-west to north-east during 2005-2006 years. The profile crosses major geological structures of Central Poland, including the Variscan Externides and Variscan foredeep, the Transeuropean Suture Zone and the marginal zone of East European Craton. The main objectives of the project include identification of sub-Zechstein sedimentary structures and evaluation of resistivity distribution within the deep crust, especially at the contact of East European Precambrian Craton and Central Europe Paleozoic structures. The length of the profile is about 700 km; 161 deep magnetotelluric sounding sites were made with a medium spacing of about 4 km. Data acquisition and processing The recording of the components of natural electromagnetic field was made with a broad range of frequencies, varying from 0.0003 Hz up to 575 Hz with use of MT-1 system of Electromagnetic Instruments Incorporation. This frequency band allowed obtaining the information about geology ranging from a few dozen meters to approximately 100 km, depending on the vertical distribution of the resistivity inside geological medium. To reduce the electromagnetic noise, magnetic and electric remote reference was applied. A remote reference site was located at a distance of over 100 km of field sites. Processing of the recorded data included the estimation of the components of impedance tensor (Zxx, Zxy, Zyx and Zyy ), with use of robust type procedures. The components of the impedance tensor allowed in a subsequent step for calculation of field curves for two orientations of the measurement system (XY - described further as the TM mode and YX - TE mode) and additional parameters of the medium like skew, strike, pole diagrams etc. Recording of the vertical component of electromagnetic field (Hz) allowed calculation of tipper parameter T. Magnetotelluric soundings interpretation Geophysical interpretation of MT sounding data was made based on 1D and 2D inversion. The upper part of the geological section is built of relatively flat layers, hence a 1D interpretation model could be effectively applied. Starting models for 1D inversion were constructed based on results of electromagnetic well-logging and some well-documented seismic horizons. Initial models for 2D inversion were constructed with the use of results of 1D magnetotelluric sounding inversion and structural model of the upper part of cross-section based on seismic data interpretation. 2D inversion was performed in two steps with use of NLCG and SBI algorithms. At first step of inversion high-frequency range of data was used and constraints based on borehole data was applied. Inversion in second step was made with starting model constructed based on results of first one and with stabilizing resistivity distribution in upper part of cross-section. Of great interest is varied resistivity of the formation resting between the Zechstein evaporate complex, and the crystalline basement. Interpretation of results of magnetotelluric soundings provide a lot of new information. The main tectonic boundaries were distinguished and location of sediments of different lithology reflected in resistivity differentiation was defined. Some new deep tectonic elements were recognized at the zone of Fore-Sudetic Block and Fore-Sudetic Monocline. Substantial differentiation of resistivity of crystalline massif of the East European Craton basement was discovered. Zones of low resistivity are probably connected with development of metamorphic processes or reflects location of big faults. Geological cross- section based on resistivity distribution was constructed. Deep model of regional structures based on resistivity distribution was suggested as well. Acknowledgments. This paper was based on results of investigations carried out by the PBG Geophysical Exploration Company Ltd. financed by the Minister of Environment through National Found for Environment Protection and Water Resources. The authors used also results of statutory research of Department of General Geology, Environment Protection and Geotourism, UST AGH, financed by the Minister of Science and Higher Education (project no 11.11.140.447). Geophysical interpretation was carried out using softwares by EMI, and Geosystem WingLinkTM.

Fluid handling equipment: A compilation

NASA Technical Reports Server (NTRS)

1976-01-01

Devices and techniques used in fluid-handling and vacuum systems are described. Section 1 presents several articles on fluid lines and tubing. Section 2 describes a number of components such as valves, filters, and regulators. The last section contains descriptions of a number of innovative fluid-handling systems.

NASA Tech Briefs, November 1998. Volume 22, No. 11

NASA Technical Reports Server (NTRS)

1998-01-01

Topics include: special coverage sections on test and measurement and sections on electronic components and circuits, electronic systems, software, materials, mechanics, machinery/automation, physical sciences, information sciences, book and reports, and special sections of Electronics Tech Briefs amd Rapid Product Development Tech Briefs.

Office of the Secretary; Civilian Health and Medical Program of the Uniformed Services (CHAMPUS); transitional assistance management program; early eligibility for TRICARE for certain reserve component members. Final rule.

PubMed

2006-06-02

This final rule revises requirements and procedures for the Transitional Assistance Management Program, which was temporarily revised by section 704 of the National Defense Authorization Act for Fiscal Year 2004 (NDAA-04) (Pub. L. 108-136) and section 1117 of the Emergency Supplemental Appropriations Act for the Reconstruction of Iraq and Afghanistan, 2004 (Emergency Supplemental) (Pub. L. 108-106), which revisions were made permanent by section 706(a) of the Ronald W. Reagan National Defense Authorization Act for Fiscal Year 2005 (NDAA-05) (Pub. L. 108-375). In addition, it establishes requirements and procedures for implementation of the earlier TRICARE eligibility for certain reserve component members authorized by section 703 of NDAA-04 and section 1116 of the Emergency Supplemental, which provisions were made permanent by section 703 of NDAA-05. The rule adopts the interim rule published in the Federal Register on March 16, 2005 (70 FR 12798).

A Study of Uncertainties for MODIS Cloud Retrievals of Optical Thickness and Effective Radius

NASA Technical Reports Server (NTRS)

Platnick, Steven; Pincus, Robert

2002-01-01

The investigation spanned four linked components as summarized in section III, each relating to some aspect of uncertainty assessment in the retrieval of cloud optical and microphysical properties using solar reflectance algorithms such as the MODIS operational cloud product (product IDS MOD06, MDY06 for Terra and Aqua, respectively). As discussed, three of these components have been fully completed (items (l), (2), and (3) while item (4) has been partially completed. These efforts have resulted in peer-reviewed publications and/or information delivered to the MODIS P.I. (M. D. King) for inclusion in the cloud product Quality Assessment (QA) output, a portion of the product output used, in part, for retrieval error assignments. This final report begins with a synopsis of the proposed investigation (section III) followed by a summary of work performed up through the last report including updates (section IV). Section V describes new activities. Publications from the efforts are listed in section VI. Figures (available in powerpoint format) are found in section VII.

Circulating ghrelin, leptin, and soluble leptin receptor concentrations and cardiometabolic risk factors in a community-based sample.

PubMed

Ingelsson, Erik; Larson, Martin G; Yin, Xiaoyan; Wang, Thomas J; Meigs, James B; Lipinska, Izabella; Benjamin, Emelia J; Keaney, John F; Vasan, Ramachandran S

2008-08-01

The conjoint effects and relative importance of ghrelin, leptin, and soluble leptin receptor (sOB-R), adipokines involved in appetite control and energy expenditure in mediating cardiometabolic risk, is unknown. The objective of the study was to study the cross-sectional relations of these adipokines to cardiometabolic risk factors in a community-based sample. We measured circulating ghrelin, leptin, and sOB-R in 362 participants (mean age 45 yr; 54% women) of the Framingham Third Generation Cohort. Body mass index, waist circumference (WC), blood pressure, lipid measures, fasting glucose, smoking, and metabolic syndrome (MetS) were measured. Ghrelin and leptin concentrations were significantly higher in women (P < 0.0001). In multivariable models, ghrelin was inversely associated with age and systolic blood pressure, and leptin was positively related to body mass index and WC. sOB-R was positively associated with age, total cholesterol, and fasting glucose and inversely with WC and high-density lipoprotein cholesterol. Ghrelin and sOB-R concentrations were significantly lower with number of MetS components (P for trend = 0.022 and < 0.0001, respectively), whereas leptin concentrations were higher (P for trend = 0.0001). Relating all adipokines to MetS conjointly, higher ghrelin and leptin concentrations were associated with decreased and increased odds of MetS (odds ratio 0.55, P < 0.0001; odds ratio 4.44, P = 0.0002, per 1 sd increase of respective log adipokine). In our community-based sample, we observed a sexual dimorphism in circulating ghrelin and leptin concentrations. Ghrelin, leptin, and sOB-R were associated with number of MetS components cross-sectionally, consistent with the hypothesis that these adipokines may have a central role in cardiometabolic risk.

Writing Assignments with a Metacognitive Component Enhance Learning in a Large Introductory Biology Course

PubMed Central

Mynlieff, Michelle; Manogaran, Anita L.; St. Maurice, Martin

2014-01-01

Writing assignments, including note taking and written recall, should enhance retention of knowledge, whereas analytical writing tasks with metacognitive aspects should enhance higher-order thinking. In this study, we assessed how certain writing-intensive “interventions,” such as written exam corrections and peer-reviewed writing assignments using Calibrated Peer Review and including a metacognitive component, improve student learning. We designed and tested the possible benefits of these approaches using control and experimental variables across and between our three-section introductory biology course. Based on assessment, students who corrected exam questions showed significant improvement on postexam assessment compared with their nonparticipating peers. Differences were also observed between students participating in written and discussion-based exercises. Students with low ACT scores benefited equally from written and discussion-based exam corrections, whereas students with midrange to high ACT scores benefited more from written than discussion-based exam corrections. Students scored higher on topics learned via peer-reviewed writing assignments relative to learning in an active classroom discussion or traditional lecture. However, students with low ACT scores (17–23) did not show the same benefit from peer-reviewed written essays as the other students. These changes offer significant student learning benefits with minimal additional effort by the instructors. PMID:26086661

Instrumental background in balloon-borne gamma-ray spectrometers and techniques for its reduction

NASA Technical Reports Server (NTRS)

Gehrels, N.

1985-01-01

Instrumental background in balloon-borne gamma-ray spectrometers is presented. The calculations are based on newly available interaction cross sections and new analytic techniques, and are the most detailed and accurate published to date. Results compare well with measurements made in the 20 keV to 10 MeV energy range by the Goddard Low Energy Gamma-ray Spectrometer (LEGS). The principal components of the continuum background in spectrometers with GE detectors and thick active shields are: (1) elastic neutron scattering of atmospheric neutrons on the Ge nuclei; (2) aperture flux of atmospheric and cosmic gamma rays; (3) beta decays of unstable nuclides produced by nuclear interactions of atmospheric protons and neutrons with Ge nuclei; and (4) shield leakage of atmospheric gamma rays. The improved understanding of these components leads to several recommended techniques for reducing the background.

Soil Components in Heterogeneous Impact Glass in Martian Meteorite EETA79001

NASA Technical Reports Server (NTRS)

Schrader, C. M.; Cohen, B. A.; Donovan, J. J.; Vicenzi, E. P.

2010-01-01

Martian soil composition can illuminate past and ongoing near-surface processes such as impact gardening [2] and hydrothermal and volcanic activity [3,4]. Though the Mars Exploration Rovers (MER) have analyzed the major-element composition of Martian soils, no soil samples have been returned to Earth for detailed chemical analysis. Rao et al. [1] suggested that Martian meteorite EETA79001 contains melted Martian soil in its impact glass (Lithology C) based on sulfur enrichment of Lithology C relative to the meteorite s basaltic lithologies (A and B) [1,2]. If true, it may be possible to extract detailed soil chemical analyses using this meteoritic sample. We conducted high-resolution (0.3 m/pixel) element mapping of Lithology C in thin section EETA79001,18 by energy dispersive spectrometry (EDS). We use these data for principal component analysis (PCA).

Design sensitivity analysis using EAL. Part 1: Conventional design parameters

NASA Technical Reports Server (NTRS)

Dopker, B.; Choi, Kyung K.; Lee, J.

1986-01-01

A numerical implementation of design sensitivity analysis of builtup structures is presented, using the versatility and convenience of an existing finite element structural analysis code and its database management system. The finite element code used in the implemenatation presented is the Engineering Analysis Language (EAL), which is based on a hybrid method of analysis. It was shown that design sensitivity computations can be carried out using the database management system of EAL, without writing a separate program and a separate database. Conventional (sizing) design parameters such as cross-sectional area of beams or thickness of plates and plane elastic solid components are considered. Compliance, displacement, and stress functionals are considered as performance criteria. The method presented is being extended to implement shape design sensitivity analysis using a domain method and a design component method.