Stiffness Characteristics of Composite Rotor Blades With Elastic Couplings

NASA Technical Reports Server (NTRS)

Piatak, David J.; Nixon, Mark W.; Kosmatka, John B.

1997-01-01

Recent studies on rotor aeroelastic response and stability have shown the beneficial effects of incorporating elastic couplings in composite rotor blades. However, none of these studies have clearly identified elastic coupling limits and the effects of elastic couplings on classical beam stiffnesses of representative rotor blades. Knowledge of these limits and effects would greatly enhance future aeroelastic studies involving composite rotor blades. The present study addresses these voids and provides a preliminary design database for investigators who may wish to study the effects of elastic couplings on representative blade designs. The results of the present study should provide a basis for estimating the potential benefits associated with incorporating elastic couplings without the need for first designing a blade cross section and then performing a cross-section analysis to obtain the required beam section properties as is customary in the usual one-dimensional beam-type approach.

Understanding Gender, Creativity, and Entrepreneurial Intentions

ERIC Educational Resources Information Center

Smith, Ronda Marie; Sardeshmukh, Shruti R.; Combs, Gwendolyn M.

2016-01-01

Purpose: The purpose of this paper is to explore the complex relationships between gender and entrepreneurial intentions. Design/methodology/approach: This paper uses a two study design where the second study is a constructive replication of the first study. The first study uses a cross-sectional design, while the second uses a design where data…

Limit states and reliability-based pipeline design. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zimmerman, T.J.E.; Chen, Q.; Pandey, M.D.

1997-06-01

This report provides the results of a study to develop limit states design (LSD) procedures for pipelines. Limit states design, also known as load and resistance factor design (LRFD), provides a unified approach to dealing with all relevant failure modes combinations of concern. It explicitly accounts for the uncertainties that naturally occur in the determination of the loads which act on a pipeline and in the resistance of the pipe to failure. The load and resistance factors used are based on reliability considerations; however, the designer is not faced with carrying out probabilistic calculations. This work is done during developmentmore » and periodic updating of the LSD document. This report provides background information concerning limits states and reliability-based design (Section 2), gives the limit states design procedures that were developed (Section 3) and provides results of the reliability analyses that were undertaken in order to partially calibrate the LSD method (Section 4). An appendix contains LSD design examples in order to demonstrate use of the method. Section 3, Limit States Design has been written in the format of a recommended practice. It has been structured so that, in future, it can easily be converted to a limit states design code format. Throughout the report, figures and tables are given at the end of each section, with the exception of Section 3, where to facilitate understanding of the LSD method, they have been included with the text.« less

77 FR 9256 - Design and Methodology for Postmarket Surveillance Studies Under Section 522 of the Federal Food...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-16

... (i) Intended to be implanted in the human body for more than 1 year or to be used to sustain or... DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration [Docket No. FDA-2012-N-0123] Design and Methodology for Postmarket Surveillance Studies Under Section 522 of the Federal Food, Drug...

Traditional Versus Online Biology Courses: Connecting Course Design and Student Learning in an Online Setting

PubMed Central

Biel, Rachel; Brame, Cynthia J.

2016-01-01

Online courses are a large and growing part of the undergraduate education landscape, but many biology instructors are skeptical about the effectiveness of online instruction. We reviewed studies comparing the effectiveness of online and face-to-face (F2F) undergraduate biology courses. Five studies compared student performance in multiple course sections at community colleges, while eight were smaller scale and compared student performance in particular biology courses at a variety of types of institutions. Of the larger-scale studies, two found that students in F2F sections outperformed students in online sections, and three found no significant difference; it should be noted, however, that these studies reported little information about course design. Of the eight smaller scale studies, six found no significant difference in student performance between the F2F and online sections, while two found that the online sections outperformed the F2F sections. In alignment with general findings about online teaching and learning, these results suggest that well-designed online biology courses can be effective at promoting student learning. Three recommendations for effective online instruction in biology are given: the inclusion of an online orientation to acclimate students to the online classroom; student-instructor and student-student interactions facilitated through synchronous and asynchronous communication; and elements that prompt student reflection and self-assessment. We conclude that well-designed online biology courses can be as effective as their traditional counterparts, but that more research is needed to elucidate specific course elements and structures that can maximize online students’ learning of key biology skills and concepts. PMID:28101268

Traditional Versus Online Biology Courses: Connecting Course Design and Student Learning in an Online Setting.

PubMed

Biel, Rachel; Brame, Cynthia J

2016-12-01

Online courses are a large and growing part of the undergraduate education landscape, but many biology instructors are skeptical about the effectiveness of online instruction. We reviewed studies comparing the effectiveness of online and face-to-face (F2F) undergraduate biology courses. Five studies compared student performance in multiple course sections at community colleges, while eight were smaller scale and compared student performance in particular biology courses at a variety of types of institutions. Of the larger-scale studies, two found that students in F2F sections outperformed students in online sections, and three found no significant difference; it should be noted, however, that these studies reported little information about course design. Of the eight smaller scale studies, six found no significant difference in student performance between the F2F and online sections, while two found that the online sections outperformed the F2F sections. In alignment with general findings about online teaching and learning, these results suggest that well-designed online biology courses can be effective at promoting student learning. Three recommendations for effective online instruction in biology are given: the inclusion of an online orientation to acclimate students to the online classroom; student-instructor and student-student interactions facilitated through synchronous and asynchronous communication; and elements that prompt student reflection and self-assessment. We conclude that well-designed online biology courses can be as effective as their traditional counterparts, but that more research is needed to elucidate specific course elements and structures that can maximize online students' learning of key biology skills and concepts.

Consistency between cross-sectional and longitudinal SNP: blood lipid associations.

PubMed

Costanza, Michael C; Beer-Borst, Sigrid; James, Richard W; Gaspoz, Jean-Michel; Morabia, Alfredo

2012-02-01

Various studies have linked different genetic single nucleotide polymorphisms (SNPs) to different blood lipids (BL), but whether these "connections" were identified using cross-sectional or longitudinal (i.e., changes over time) designs has received little attention. Cross-sectional and longitudinal assessments of BL [total, high-, low-density lipoprotein cholesterol (TC, HDL, LDL), triglycerides (TG)] and non-genetic factors (body mass index, smoking, alcohol intake) were measured for 2,002 Geneva, Switzerland, adults during 1999-2008 (two measurements, median 6 years apart), and 20 SNPs in 13 BL metabolism-related genes. Fixed and mixed effects repeated measures linear regression models, respectively, were employed to identify cross-sectional and longitudinal SNP:BL associations among the 1,516 (76%) study participants who reported not being treated for hypercholesterolemia at either measurement time. One-third more (12 vs. 9) longitudinal than cross-sectional associations were found [Bonferroni-adjusted two-tailed p < 0.00125 (=0.05/2)/20) for each of the four ensembles of 20 SNP:individual BL associations tested under the two study designs]. There was moderate consistency between the cross-sectional and longitudinal findings, with eight SNP:BL associations consistently identified across both study designs: [APOE.2 and APOE.4 (rs7412 and rs429358)]:TC; HL/LIPC (rs2070895):HDL; [APOB (rs1367117), APOE.2 and APOE.4 (rs7412 and rs429358)]:LDL; [APOA5 (rs2072560) and APOC III (rs5128)]:TG. The results suggest that cross-sectional studies, which include most genome-wide association studies (GWAS), can assess the large majority of SNP:BL associations. In the present analysis, which was much less powered than a GWAS, the cross-sectional study was around 2/3 (67%) as efficient as the longitudinal study.

Urban Children in Distress: An Introduction to the Issues. Innocenti Occasional Papers. The Urban Child Series, Number 2.

ERIC Educational Resources Information Center

Blanc, Cristina S.

This publication presents a discussion of the status of poor urban children world-wide and the design of a five-nation study of the condition of distressed urban children. Following an introduction, Section 2 describes the urban child project designed to study and advance the plight of urban children in developing nations. Section 3 outlines the…

Social Studies: A Guide for Curriculum Development.

ERIC Educational Resources Information Center

Indiana State Dept. of Public Instruction, Indianapolis.

This social studies curriculum guide is designed for grades K-12. Divided into seven sections, the first section offers a brief introduction and calls attention to the laws and rulings in Indiana which affect the teaching of social studies. Section two outlines the guide's rationale which stresses that knowledge must be combined with rational…

Incorporating Skills into Social Studies Programs, K-12.

ERIC Educational Resources Information Center

Gregory, George, Ed.

Designed to assist schools in implementing developmental skills in the social studies programs for grades K-12, this guide is divided into seven sections. The first section, a literature review, cites publications on social studies skills. Section 2 gives an interdisciplinary view of shared skills in the New York state curriculum. Three skill…

The Neighbourhood Effects on Health and Well-being (NEHW) study.

PubMed

O'Campo, Patricia; Wheaton, Blair; Nisenbaum, Rosane; Glazier, Richard H; Dunn, James R; Chambers, Catharine

2015-01-01

Many cross-sectional studies of neighbourhood effects on health do not employ strong study design elements. The Neighbourhood Effects on Health and Well-being (NEHW) study, a random sample of 2412 English-speaking Toronto residents (age 25-64), utilises strong design features for sampling neighbourhoods and individuals, characterising neighbourhoods using a variety of data sources, measuring a wide range of health outcomes, and for analysing cross-level interactions. We describe here methodological issues that shaped the design and analysis features of the NEHW study to ensure that, while a cross-sectional sample, it will advance the quality of evidence emerging from observational studies. Copyright © 2014 The Authors. Published by Elsevier Ltd.. All rights reserved.

Advanced Transportation System Studies Technical Area 2 (TA-2) Heavy Lift Launch Vehicle Development Contract. Volume 2; Technical Results

NASA Technical Reports Server (NTRS)

1995-01-01

The sections in this report include: Single Stage to Orbit (SSTO) Design Ground-rules; Operations Issues and Lessons Learned; Vertical-Takeoff/Landing Versus Vertical-Takeoff/Horizontal-Landing; SSTO Design Results; SSTO Simulation Results; SSTO Assessment Results; SSTO Sizing Tool User's Guide; SSto Turnaround Assessment Report; Ground Operations Assessment First Year Executive Summary; Health Management System Definition Study; Major TA-2 Presentations; First Lunar Outpost Heavy Lift Launch Vehicle Design and Assessment; and the section, Russian Propulsion Technology Assessment Reports.

Who Gets Designated a Terrorist and Why?

ERIC Educational Resources Information Center

Beck, Colin J.; Miner, Emily

2013-01-01

This study examines formal terrorism designations by governments through the lens of organization studies research on categorization processes. It is argued that designations hinge on markers from the organizational profile of a militant group. Using cross-sectional data on militant organizations and designations by the United States, the United…

Amphetamine-type stimulants and HIV infection among men who have sex with men: implications on HIV research and prevention from a systematic review and meta-analysis

PubMed Central

Thu Vu, Nga Thi; Maher, Lisa; Zablotska, Iryna

2015-01-01

Introduction HIV infections and the use of amphetamine-type stimulants (ATS) among men who have sex with men (MSM) have been increasing internationally, but the role of ATS use as a co-factor for HIV infection remains unclear. We aimed to summarize the association between ATS use and HIV infection among MSM. Methods We conducted a systematic search of MEDLINE, EMBASE, GLOBAL HEALTH and PsycINFO for relevant English, peer-reviewed articles of quantitative studies published between 1980 and 25 April 2013. Pooled estimates of the association – prevalence rate ratios (PRR, cross-sectional studies), odds ratio (OR, case-control studies) and hazard ratio (HR, longitudinal studies), with 95% Confidence Intervals (CI) – were calculated using random-effects models stratified by study design and ATS group (meth/amphetamines vs. ecstasy). We assessed the existence of publication bias in funnel plots and checked for sources of heterogeneity using meta-regression and subgroup analysis. Results We identified 6710 article titles, screened 1716 abstracts and reviewed 267 full text articles. A total of 35 publications were eligible for data abstraction and meta-analysis, resulting in 56 records of ATS use. Most studies (31/35) were conducted in high-income countries. Published studies used different research designs, samples and measures of ATS use. The pooled association between meth/amphetamine use and HIV infection was statistically significant in all three designs (PRR=1.86; 95% CI: 1.57–2.17; OR=2.73; 95% CI: 2.16–3.46 and HR=3.43; 95% CI: 2.98–3.95, respectively, for cross-sectional, case-control and longitudinal studies). Ecstasy use was not associated with HIV infection in cross-sectional studies (PRR=1.15; 95% CI: 0.88–1.49; OR=3.04; 95% CI: 1.29–7.18 and HR=2.48; 95% CI: 1.42–4.35, respectively, for cross-sectional, case-control and longitudinal studies). Results in cross-sectional studies were highly heterogeneous due to issues with ATS measurement and different sampling frames. Conclusions While meth/amphetamine use was significantly associated with HIV infection among MSM in high-income countries in all study designs, evidence of the role of ecstasy in HIV infection was lacking in cross-sectional studies. Cross-sectional study design, measurement approaches and source populations may also be important modifiers of the strength and the direction of associations. Event-specific measure of individual drug is required to establish temporal relationship between ATS use and HIV infection. HIV prevention programmes targeting MSM should consider including interventions designed to address meth/amphetamine use. PMID:25609214

Methodology for safety optimization of highway cross-sections for horizontal curves with restricted sight distance.

PubMed

Ibrahim, Shewkar E; Sayed, Tarek; Ismail, Karim

2012-11-01

Several earlier studies have noted the shortcomings with existing geometric design guides which provide deterministic standards. In these standards the safety margin of the design output is generally unknown and there is little knowledge of the safety implications of deviating from the standards. To mitigate these shortcomings, probabilistic geometric design has been advocated where reliability analysis can be used to account for the uncertainty in the design parameters and to provide a mechanism for risk measurement to evaluate the safety impact of deviations from design standards. This paper applies reliability analysis for optimizing the safety of highway cross-sections. The paper presents an original methodology to select a suitable combination of cross-section elements with restricted sight distance to result in reduced collisions and consistent risk levels. The purpose of this optimization method is to provide designers with a proactive approach to the design of cross-section elements in order to (i) minimize the risk associated with restricted sight distance, (ii) balance the risk across the two carriageways of the highway, and (iii) reduce the expected collision frequency. A case study involving nine cross-sections that are parts of two major highway developments in British Columbia, Canada, was presented. The results showed that an additional reduction in collisions can be realized by incorporating the reliability component, P(nc) (denoting the probability of non-compliance), in the optimization process. The proposed approach results in reduced and consistent risk levels for both travel directions in addition to further collision reductions. Copyright © 2012 Elsevier Ltd. All rights reserved.

21 CFR 312.120 - Foreign clinical studies not conducted under an IND.

Code of Federal Regulations, 2010 CFR

2010-04-01

... HUMAN SERVICES (CONTINUED) DRUGS FOR HUMAN USE INVESTIGATIONAL NEW DRUG APPLICATION Miscellaneous § 312... the act or section 351 of the Public Health Service Act (the PHS Act) (42 U.S.C. 262)) a well-designed... this section, GCP is defined as a standard for the design, conduct, performance, monitoring, auditing...

Future design of perpetual pavements for New Mexico.

DOT National Transportation Integrated Search

2009-12-29

This study provides guidance for future designs of perpetual pavements in New Mexico. The perpetual pavement in this study refers to only hot mix asphalt (HMA) pavement sections designed for a useful life of 50 years or more without having major dist...

Research studies on advanced optical module/head designs for optical devices

NASA Technical Reports Server (NTRS)

Burke, James J.

1991-01-01

A summary is presented of research in optical data storage materials and of research at the center. The first section contains summary reports under the general headings of: (1) Magnetooptic media: modeling, design, fabrication, characterization, and testing; (2) Optical heads: holographic optical elements; and (3) Optical heads: integrated optics. The second section consist of a proposal entitled, Signal Processing Techniques for Optical Data Storage. And section three presents various publications prepared by the center.

Arrow-wing supersonic cruise aircraft structural design concepts evaluation. Volume 1: Sections 1 through 6

NASA Technical Reports Server (NTRS)

Sakata, I. F.; Davis, G. W.

1975-01-01

The structural approach best suited for the design of a Mach 2.7 arrow-wing supersonic cruise aircraft was investigated. Results, procedures, and principal justification of results are presented. Detailed substantiation data are given. In general, each major analysis is presented sequentially in separate sections to provide continuity in the flow of the design concepts analysis effort. In addition to the design concepts evaluation and the detailed engineering design analyses, supporting tasks encompassing: (1) the controls system development; (2) the propulsion-airframe integration study; and (3) the advanced technology assessment are presented.

Comparative Evaluation of Stress Distribution in Experimentally Designed Nickel-titanium Rotary Files with Varying Cross Sections: A Finite Element Analysis.

PubMed

Basheer Ahamed, Shadir Bughari; Vanajassun, Purushothaman Pranav; Rajkumar, Kothandaraman; Mahalaxmi, Sekar

2018-04-01

Single cross-sectional nickel-titanium (NiTi) rotary instruments during continuous rotations are subjected to constant and variable stresses depending on the canal anatomy. This study was intended to create 2 new experimental, theoretic single-file designs with combinations of triple U (TU), triangle (TR), and convex triangle (CT) cross sections and to compare their bending stresses in simulated root canals with a single cross-sectional instrument using finite element analysis. A 3-dimensional model of the simulated root canal with 45° curvature and NiTi files with 5 cross-sectional designs were created using Pro/ENGINEER Wildfire 4.0 software (PTC Inc, Needham, MA) and ANSYS software (version 17; ANSYS, Inc, Canonsburg, PA) for finite element analysis. The NiTi files of 3 groups had single cross-sectional shapes of CT, TR, and TU designs, and 2 experimental groups had a CT, TR, and TU (CTU) design and a TU, TR, and CT (UTC) design. The file was rotated in simulated root canals to analyze the bending stress, and the von Mises stress value for every file was recorded in MPa. Statistical analysis was performed using the Kruskal-Wallis test and the Bonferroni-adjusted Mann-Whitney test for multiple pair-wise comparison with a P value <.05 (95 %). The maximum bending stress of the rotary file was observed in the apical third of the CT design, whereas comparatively less stress was recorded in the CTU design. The TU and TR designs showed a similar stress pattern at the curvature, whereas the UTC design showed greater stress in the apical and middle thirds of the file in curved canals. All the file designs showed a statistically significant difference. The CTU designed instruments showed the least bending stress on a 45° angulated simulated root canal when compared with all the other tested designs. Copyright © 2017 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Interim report on roughness measurement of elevated roadway sections : I-10 Laplace - Kenner, I-10 Henderson - Grosse Tete.

DOT National Transportation Integrated Search

1973-09-01

Two sections of Interstate 10 have been selected for study to determine the initial roughness and subsequent change in roughness with time. The two sections represent different design and construction procedures. : Section 1 is located on I-10 betwee...

Evaluating Learning Management System (LMS)-Facilitated Delivery of Universal Design for Learning (UDL)

ERIC Educational Resources Information Center

Bryans Bongey, Sarah

2012-01-01

This quantitative study involved 157 students in two sections of an undergraduate class in general biology, as well as one instructor who taught both sections of the course. It used resources from the Center for Applied Special Technologies (CAST) to evaluate the viability of a Learning Management System (LMS) to provide Universal Design for…

Exploring Structural Dynamics within and between Sensory and Intellectual Functioning in Old and Very Old Age: Longitudinal Evidence from the Berlin Aging Study

ERIC Educational Resources Information Center

Ghisletta, Paolo; Lindenberger, Ulman

2005-01-01

Cross-sectional and longitudinal analyses of age-heterogeneous samples have revealed correlational links between and within intellectual, sensory, and sensorimotor domains. Due to basic limitations of cross-sectional designs and a reluctance to disentangle antecedent-consequent relations in longitudinal designs, the functional significance and…

Advanced designs for non-imaging submillimeter-wave Winston cone concentrators

NASA Astrophysics Data System (ADS)

Nelson, A. O.; Grossman, E. N.

2014-05-01

We describe the design and simulation of several non-imaging concentrators designed to couple submillimeter wavelength radiation from free space into highly overmoded, rectangular, WR-10 waveguide. Previous designs are altered to improve the uniformity of efficiency rather than the efficiency itself. The concentrators are intended for use as adapters between instruments using overmoded WR-10 waveguide as input or output and sources propagating through free space. Previous simulation and measurement have shown that the angular response is primarily determined by the Winston cone and is well predicted by geometric optics theory while the efficiencies are primarily determined by the transition section. Additionally, previous work has shown insensitivity to polarization, orientation and beam size. Several separate concentrator designs are studied, all of which use a Winston cone (also known as a compound parabolic concentrator) with an input diameter ranging from 4 mm to 16 mm, and "throat" diameters of less than 0.5 mm to 4 mm as the initial interface. The use of various length adiabatic circular-to-rectangular transition sections is investigated, along with the effect of an additional, 25 mm waveguide section designed to model the internal waveguide of the power meter. Adapters without a transition section and a rectangular Winston cone throat aperture and double cone configurations are also studied. Adapters are analyzed in simulation for consistent efficiency across the opening aperture.

Coal Mine Roadway Stability in Soft Rock: A Case Study

NASA Astrophysics Data System (ADS)

Shen, Baotang

2014-11-01

Roadway instability has always been a major concern in deep underground coal mines where the surrounding rock strata and coal seams are weak and the in situ stresses are high. Under the high overburden and tectonic stresses, roadways could collapse or experience excessive deformation, which not only endangers mining personnel but could also reduce the functionality of the roadway and halt production. This paper describes a case study on the stability of roadways in an underground coal mine in Shanxi Province, China. The mine was using a longwall method to extract coal at a depth of approximately 350 m. Both the coal seam and surrounding rock strata were extremely weak and vulnerable to weathering. Large roadway deformation and severe roadway instabilities had been experienced in the past, hence, an investigation of the roadway failure mechanism and new support designs were needed. This study started with an in situ stress measurement programme to determine the stress orientation and magnitude in the mine. It was found that the major horizontal stress was more than twice the vertical stress in the East-West direction, perpendicular to the gateroads of the longwall panel. The high horizontal stresses and low strength of coal and surrounding rock strata were the main causes of roadway instabilities. Detailed numerical modeling was conducted to evaluate the roadway stability and deformation under different roof support scenarios. Based on the modeling results, a new roadway support design was proposed, which included an optimal cable/bolt arrangement, full length grouting, and high pre-tensioning of bolts and cables. It was expected the new design could reduce the roadway deformation by 50 %. A field experiment using the new support design was carried out by the mine in a 100 m long roadway section. Detailed extensometry and stress monitorings were conducted in the experimental roadway section as well as sections using the old support design. The experimental section produced a much better roadway profile than the previous roadway sections. The monitoring data indicated that the roadway deformation in the experimental section was at least 40-50 % less than the previous sections. This case study demonstrated that through careful investigation and optimal support design, roadway stability in soft rock conditions can be significantly improved.

Online and Social Networking Interventions for the Treatment of Depression in Young People: A Systematic Review

PubMed Central

Goodall, Joanne; Hetrick, Sarah E; Parker, Alexandra G; Gilbertson, Tamsyn; Amminger, G. Paul; Davey, Christopher G; McGorry, Patrick D; Gleeson, John; Alvarez-Jimenez, Mario

2014-01-01

Background Major depression accounts for the greatest burden of all diseases globally. The peak onset of depression occurs between adolescence and young adulthood, and for many individuals, depression displays a relapse-remitting and increasingly severe course. Given this, the development of cost-effective, acceptable, and population-focused interventions for depression is critical. A number of online interventions (both prevention and acute phase) have been tested in young people with promising results. As these interventions differ in content, clinician input, and modality, it is important to identify key features (or unhelpful functions) associated with treatment outcomes. Objective A systematic review of the research literature was undertaken. The review was designed to focus on two aspects of online intervention: (1) standard approaches evaluating online intervention content in randomized controlled designs (Section 1), and (2) second-generation online interventions and services using social networking (eg, social networking sites and online support groups) in any type of research design (Section 2). Methods Two specific literature searches were undertaken. There was no date range specified. The Section 1 search, which focused on randomized controlled trials, included only young people (12-25 years) and yielded 101 study abstracts, of which 15 met the review inclusion criteria. The Section 2 search, which included all study design types and was not restricted in terms of age, yielded 358 abstracts, of which 22 studies met the inclusion criteria. Information about the studies and their findings were extracted and tabulated for review. Results The 15 studies identified in Section 1 described 10 trials testing eight different online interventions, all of which were based on a cognitive behavioral framework. All but one of the eight identified studies reported positive results; however, only five of the 15 studies used blinded interviewer administered outcomes with most trials using self-report data. Studies varied significantly in presentation of intervention content, treatment dose, and dropout. Only two studies included moderator or clinician input. Results for Section 2 were less consistent. None of the Section 2 studies reported controlled or randomized designs. With the exception of four studies, all included participants were younger than 25 years of age. Eight of the 16 social networking studies reported positive results for depression-related outcomes. The remaining studies were either mixed or negative. Findings for online support groups tended to be more positive; however, noteworthy risks were identified. Conclusions Online interventions with a broad cognitive behavioral focus appear to be promising in reducing depression symptomology in young people. Further research is required into the effectiveness of online interventions delivering cognitive behavioral subcomponents, such as problem-solving therapy. Evidence for the use of social networking is less compelling, although limited by a lack of well-designed studies and social networking interventions. A range of future social networking therapeutic opportunities are highlighted. PMID:25226790

Online and social networking interventions for the treatment of depression in young people: a systematic review.

PubMed

Rice, Simon M; Goodall, Joanne; Hetrick, Sarah E; Parker, Alexandra G; Gilbertson, Tamsyn; Amminger, G Paul; Davey, Christopher G; McGorry, Patrick D; Gleeson, John; Alvarez-Jimenez, Mario

2014-09-16

Major depression accounts for the greatest burden of all diseases globally. The peak onset of depression occurs between adolescence and young adulthood, and for many individuals, depression displays a relapse-remitting and increasingly severe course. Given this, the development of cost-effective, acceptable, and population-focused interventions for depression is critical. A number of online interventions (both prevention and acute phase) have been tested in young people with promising results. As these interventions differ in content, clinician input, and modality, it is important to identify key features (or unhelpful functions) associated with treatment outcomes. A systematic review of the research literature was undertaken. The review was designed to focus on two aspects of online intervention: (1) standard approaches evaluating online intervention content in randomized controlled designs (Section 1), and (2) second-generation online interventions and services using social networking (eg, social networking sites and online support groups) in any type of research design (Section 2). Two specific literature searches were undertaken. There was no date range specified. The Section 1 search, which focused on randomized controlled trials, included only young people (12-25 years) and yielded 101 study abstracts, of which 15 met the review inclusion criteria. The Section 2 search, which included all study design types and was not restricted in terms of age, yielded 358 abstracts, of which 22 studies met the inclusion criteria. Information about the studies and their findings were extracted and tabulated for review. The 15 studies identified in Section 1 described 10 trials testing eight different online interventions, all of which were based on a cognitive behavioral framework. All but one of the eight identified studies reported positive results; however, only five of the 15 studies used blinded interviewer administered outcomes with most trials using self-report data. Studies varied significantly in presentation of intervention content, treatment dose, and dropout. Only two studies included moderator or clinician input. Results for Section 2 were less consistent. None of the Section 2 studies reported controlled or randomized designs. With the exception of four studies, all included participants were younger than 25 years of age. Eight of the 16 social networking studies reported positive results for depression-related outcomes. The remaining studies were either mixed or negative. Findings for online support groups tended to be more positive; however, noteworthy risks were identified. Online interventions with a broad cognitive behavioral focus appear to be promising in reducing depression symptomology in young people. Further research is required into the effectiveness of online interventions delivering cognitive behavioral subcomponents, such as problem-solving therapy. Evidence for the use of social networking is less compelling, although limited by a lack of well-designed studies and social networking interventions. A range of future social networking therapeutic opportunities are highlighted.

Global Cost and Weight Evaluation of Fuselage Side Panel Design Concepts

NASA Technical Reports Server (NTRS)

Polland, D. R.; Finn, S. R.; Griess, K. H.; Hafenrichter, J. L.; Hanson, C. T.; Ilcewicz, L. B.; Metschan, S. L.; Scholz, D. B.; Smith, P. J.

1997-01-01

This report documents preliminary design trades conducted under NASA contracts NAS1 18889 (Advanced Technology Composite Aircraft Structures, ATCAS) and NAS1-19349 (Task 3, Pathfinder Shell Design) for a subsonic wide body commercial aircraft fuselage side panel section utilizing composite materials. Included in this effort were (1) development of two complete design concepts, (2) generation of cost and weight estimates, (3) identification of technical issues and potential design enhancements, and (4) selection of a single design to be further developed. The first design concept featured an open-section stringer stiffened skin configuration while the second was based on honeycomb core sandwich construction. The trade study cost and weight results were generated from comprehensive assessment of each structural component comprising the fuselage side panel section from detail fabrication through airplane final assembly. Results were obtained in three phases: (1) for the baseline designs, (2) after global optimization of the designs, and (3) the results anticipated after detailed design optimization. A critical assessment of both designs was performed to determine the risk associated with each concept, that is the relative probability of achieving the cost and weight projections. Seven critical technical issues were identified as the first step towards side panel detailed design optimization.

Examining Development of Curriculum Knowledge of Prospective Mathematics Teachers

ERIC Educational Resources Information Center

Sahin, Ömer; Soylu, Yasin

2017-01-01

Explanatory-confirmatory research design, one of the mixed methods research designs, was used in this study to investigate Curriculum Knowledge developments of prospective teachers regarding algebra. Cross-sectional study method, as a type of descriptive research and one of the non-experimental research designs, was used to collect quantitative…

Design and implementation of observational studies to measure disease burden with a focus on stroke.

PubMed

Howard, George; Howard, Virginia J

2018-02-01

Observational epidemiological studies have the dual goals of measuring disease burden and assessing the association between exposures and outcomes. This report focuses on the first of these goals and provides an overview of design considerations of commonly used approaches, specifically community surveillance studies, cross-sectional studies, and longitudinal cohort studies. Each of these designs has strengths and weaknesses, with no study design being superior in all cases. Rather, these designs are complementary to achieve a better understanding of the burden of stroke.

The Emergence of Women in West Virginia History: A Title IX Project for Social Studies.

ERIC Educational Resources Information Center

Butler, Dee

This booklet was designed to be used as a supplemental social studies unit and is divided into four sections. Section 1 profiles famous women of West Virginia including Aracoma, Nancy Hanks Lincoln, Mary Harris Jones, Susan Matilda Dew Hoff, Frances Benjamin Johnston, and Nancy Hart Douglas. Section 2, profiles contemporary women in West Virginia…

Performance evaluation of Arizona's LTPP SPS-1 project : strategic study of flexible pavement structural factors.

DOT National Transportation Integrated Search

2012-01-01

As part of the Long Term Pavement Performance (LTPP) Program, Arizona DOT constructed 16 SPS-1 test : sections on U.S. Route 93 near Kingman. The SPS-1 study was designed to study a variety of structural : sections in new asphalt concrete constructio...

Knowledge of Metabolic Syndrome in Chinese Adults: Implications for Health Education

ERIC Educational Resources Information Center

Lo, Sally Wai Sze; Chair, Sek Ying; Lee, Iris Fung Kam

2016-01-01

Objective: The objective of this study was to assess knowledge of metabolic syndrome (MS) among Chinese adults and provide directions for designing healthcare promotion schemes for improving MS awareness in the community. Design: The study adopted a cross-sectional design and a convenience sampling method. Method: Chinese adults aged 18-65 years…

Route 139 rehabilitation: Pulaski Skyway contract 2 : technical brief.

DOT National Transportation Integrated Search

2017-06-01

This study addressed the need for an aesthetically pleasing historic concrete balustrade design alternative for the Pulaski Skyway in Jersey City, Hudson County. In this study, a crashworthy design was developed according to AASHTO Section 13 specifi...

7 CFR 1737.32 - Loan Design (LD).

Code of Federal Regulations, 2012 CFR

2012-01-01

... Studies-Area Coverage Survey and Loan Design § 1737.32 Loan Design (LD). (a) A loan application requires supporting data collectively called a “Loan Design.” The LD contains a forecast of service requirements and a... 7 Agriculture 11 2012-01-01 2012-01-01 false Loan Design (LD). 1737.32 Section 1737.32 Agriculture...

7 CFR 1737.32 - Loan Design (LD).

Code of Federal Regulations, 2013 CFR

2013-01-01

... Studies-Area Coverage Survey and Loan Design § 1737.32 Loan Design (LD). (a) A loan application requires supporting data collectively called a “Loan Design.” The LD contains a forecast of service requirements and a... 7 Agriculture 11 2013-01-01 2013-01-01 false Loan Design (LD). 1737.32 Section 1737.32 Agriculture...

7 CFR 1737.32 - Loan Design (LD).

Code of Federal Regulations, 2010 CFR

2010-01-01

... Studies-Area Coverage Survey and Loan Design § 1737.32 Loan Design (LD). (a) A loan application requires supporting data collectively called a “Loan Design.” The LD contains a forecast of service requirements and a... 7 Agriculture 11 2010-01-01 2010-01-01 false Loan Design (LD). 1737.32 Section 1737.32 Agriculture...

7 CFR 1737.32 - Loan Design (LD).

Code of Federal Regulations, 2011 CFR

2011-01-01

... Studies-Area Coverage Survey and Loan Design § 1737.32 Loan Design (LD). (a) A loan application requires supporting data collectively called a “Loan Design.” The LD contains a forecast of service requirements and a... 7 Agriculture 11 2011-01-01 2011-01-01 false Loan Design (LD). 1737.32 Section 1737.32 Agriculture...

7 CFR 1737.32 - Loan Design (LD).

Code of Federal Regulations, 2014 CFR

2014-01-01

... Studies-Area Coverage Survey and Loan Design § 1737.32 Loan Design (LD). (a) A loan application requires supporting data collectively called a “Loan Design.” The LD contains a forecast of service requirements and a... 7 Agriculture 11 2014-01-01 2014-01-01 false Loan Design (LD). 1737.32 Section 1737.32 Agriculture...

Difficulties of Student Teachers in the Engineering Graphics and Design Course at a South African University: Snapshot on Sectional Drawing

ERIC Educational Resources Information Center

Makgato, Moses; Khoza, Samuel D.

2016-01-01

Engineering Graphics and Design (EGD) is a university course that teaches a medium of communication in the form of drawings. This study was undertaken to investigate factors associated with the difficulties experienced by student teachers in the sectional drawing component of the EGD course. Purposive sampling was used to select 40 students…

Fostering Entrepreneurship through Business Incubation: The Role and Prospects of Postsecondary Vocational-Technical Education. Report 2: Case Studies.

ERIC Educational Resources Information Center

Hernandez-Gantes, Victor M.; And Others

This report presents nine case studies featuring efforts to foster community development through business incubation and entrepreneurial programs at two-year colleges. A background section discusses case description, and organization and format of case studies. The second section describes the case study design. Each case study is introduced with…

Annual Review of Asian American Psychology, 2014

PubMed Central

Kim, Su Yeong; Shen, Yishan; Hou, Yang; Tilton, Kelsey E.; Juang, Linda; Wang, Yijie

2015-01-01

This 2014 review of Asian American psychology is the sixth review in the series. It includes 316 articles that met the inclusion criteria established by the past five annual reviews. Featured articles were derived from three sources: 137 were generated via the search term “Asian American” in PyscINFO, 111 were generated via a search for specific Asian American ethnic groups, and 32 were generated via author searches of articles that met the inclusion criteria. The top primary topic was health and health-related behaviors, the most frequently employed study design was cross-sectional, and the most studied Asian American ethnic group was Chinese. This year’s review includes information on the target population of the primary topic, the age range and developmental period of participants, and whether the study design was cross-sectional or longitudinal. It also identifies top authors and journals contributing to the 2014 annual review. These new features reveal that the most common target population of the primary topic was youths; studies most commonly included emerging adults ages 18–25; cross-sectional study design was employed more often than longitudinal design; the top contributor to the 2014 review was Stephen Chen, who authored the highest number of papers included; and the Asian American Journal of Psychology generated the highest number of publications for this review. PMID:26925199

Ohio Studies: Minimum Standards Leadership Series 1985.

ERIC Educational Resources Information Center

Ohio State Dept. of Education, Columbus. Div. of Elementary and Secondary Education.

This monograph is designed to provide materials, ideas, and strategies for school districts and teachers to broaden and expand the standards and requirements of Ohio studies. Section 1, "Introduction" provides an overview of the monograph. Section 2, "Organizing for Instruction" gives several alternative approaches to designing…

[IBEAS design: adverse events prevalence in Latin American hospitals].

PubMed

Aranaz-Andrés, J M; Aibar-Remón, C; Limón-Ramírez, R; Amarilla, A; Restrepo, F R; Urroz, O; Sarabia, O; Inga, R; Santivañez, A; Gonseth-García, J; Larizgoitia-Jauregui, I; Agra-Varela, Y; Terol-García, E

2011-01-01

To describe the methodological characteristics of the IBEAS study: adverse events prevalence in Latin American hospitals, with the aim of analysing the magnitude, significance and impact of adverse events (AE); to identify the main problems associated with patient safety AE; to increase the capacity of professionals involved in patient safety; and the setting up of patient safety agendas in the participating countries. A patient safety study launched in 35 Latin American hospitals through the analysis of AE in 5 countries: Argentina, Colombia, Costa Rica, Mexico and Peru, using a cross-sectional study using a review of clinical records as the main method. The implications of using a cross-sectional design when studying AE are described, in terms of resources required, internal validity and usefulness related to risk management. The cross-sectional design seems an efficient methodology in terms of time and resources spent, as well as being easy to carry out. Although the cross-sectional design does not review the all hospital episodes, it is able to provide a reliable estimate of prevalence and to support a surveillance system. Because of a possible survival bias, it is likely that the AE which led to hospital admissions will be overestimated, as well as the health related infections or those adverse events which are difficult to identify if the patient is not examined (e.g. contusions). Communication with the ward staff (if the patient is still hospitalised) help in finding the causality and their prevention. Copyright © 2010 SECA. Published by Elsevier Espana. All rights reserved.

The stability of cassette walls in compression

NASA Astrophysics Data System (ADS)

Voutay, Pierre-Arnaud

Much research into the behaviour of cold formed steel columns in the last decade has focused on channel sections undergoing local, distortional and overall buckling. Light gauge steel cassette sections are a particular form of channel section which offers an alternative form of load-bearing wall assembly for use in low-rise steel framed construction. Cassette wall sections possess wide and slender flanges so that, by including intermediate stiffeners in these wide flanges, a significant increase in the ultimate load capacity may be achieved. However, the introduction of intermediate stiffeners also increases the number of buckling modes (stiffener buckling) and, therefore complicates the behaviour and increases the risk of interactive buckling between these modes. The work undertaken in this thesis aims to clarify the behaviour of wide flanges in compression with and without intermediate stiffeners. In this research, the distortional mode of web and narrow flange buckling was inhibited by connecting the narrow flanges of the cassettes together at suitable intervals. "Generalised Beam Theory" (GBT), which allows the individual buckling modes to be considered individually and in predetermined combinations, provides a particularly good tool with which to analyse and understand the buckling behaviour of cassette sections with and without intermediate stiffeners. "Generalised Beam Theory" (GBT) is used throughout this work to determine the elastic buckling stress of the sections studied (simply supported stiffened plates, as well as cassette sections). Since the economic design of cold-formed steel sections requires the consideration of post- buckling behaviour, elastic buckling values are not directly comparable with design code values which are usually based on the concept of effective width. Therefore, finite element analysis with both material and geometric nonlinearity has also been carried out in order to obtain the ultimate strength in the critical mode or mode combination. Firstly the results of experimental test are analysed and their behaviour reproduced numerically. This serves to explain the test results and verify the numerical model. Confidence in modelling non-linear instability phenomena with the finite element method is acquired. Secondly, an initial parametric study was undertaken on the behaviour of cassette sections with and without intermediate stiffeners. This study considers the effect of the length and overall buckling on the behaviour of cassette sections, the effect of load eccentricity and the effect of the rotational restraint given by the web to the stiffened wide flange. A second parametric study including 96 specimens was undertaken next. This study considered the effect of the number (up to three intermediate stiffeners) and sizes of intermediate stiffeners on slender flanges with a slenderness ratio between 150 ≤ w/t ≤ 600. A wide range of geometries was studied covering single and interactive buckling modes. Comparison of the ultimate strength obtained from finite element analysis with the ultimate strength obtained using the effective width approach of modem design codes such as Eurocode 3 part 1.3 (1996) and NAS (North American specification (2001)) was then possible. By integrating the stress distribution over the length of the specimen, the stiffened wide flange can be isolated from the rest of the section (webs and narrow flanges). Design procedures tor plate elements incorporating one or two intermediate stiffeners under compressive load are given in Eurocode 3; Part 1.3. However, cassette sections, which have wider and more slender flanges than typical sheeting and decking, are increasingly being used in practical construction. For such cases, the design procedures in Eurocode 3 are less well founded. An improvement of the Eurocode 3 procedure dealing with intermediate stiffeners is proposed and validated for one, two or three stiffeners. Throughout the work, simple expressions suitable for design calculations are presented. Modern design codes as well as Direct Strength Method are evaluated in the light of findings of this work and wherever possible suggestions for improvements are made.

LUTE telescope structural design

NASA Technical Reports Server (NTRS)

Ruthven, Gregory

1993-01-01

The major objective of the Lunar Ultraviolet Transit Experiment (LUTE) Telescope Structural Design Study was to investigate the feasibility of designing an ultralightweight 1-m aperture system within optical performance requirements and mass budget constraints. This study uses the results from our previous studies on LUTE as a basis for further developing the LUTE structural architecture. After summarizing our results in Section 2, Section 3 begins with the overall logic we used to determine which telescope 'structural form' should be adopted for further analysis and weight estimates. Specific telescope component analysis showing calculated fundamental frequencies and how they compare with our derived requirements are included. 'First-order' component stress analyses to ensure telescope optical and structural component (i.e. mirrors & main bulkhead) weights are realistic are presented. Layouts of both the primary and tertiary mirrors showing dimensions that are consistent with both our weight and frequency calculations also form part of Section 3. Section 4 presents our calculated values for the predicted thermally induced primary-to-secondary mirror despace motion due to the large temperature range over which LUTE must operate. Two different telescope design approaches (one which utilizes fused quartz metering rods and one which assumes the entire telescope is fabricated from beryllium) are considered in this analysis. We bound the secondary mirror focus mechanism range (in despace) based on these two telescope configurations. In Section 5 we show our overall design of the UVTA (Ultraviolet Telescope Assembly) via an 'exploded view' of the sub-system. The 'exploded view' is annotated to help aid in the understanding of each sub-assembly. We also include a two view layout of the UVTA from which telescope and telescope component dimensions can be measured. We conclude our study with a set of recommendations not only with respect to the LUTE structural architecture but also on other topics related to the overall feasibility of the LUTE telescope sub-system.

21 CFR 58.61 - Equipment design.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 1 2010-04-01 2010-04-01 false Equipment design. 58.61 Section 58.61 Food and... PRACTICE FOR NONCLINICAL LABORATORY STUDIES Equipment § 58.61 Equipment design. Equipment used in the... of appropriate design and adequate capacity to function according to the protocol and shall be...

21 CFR 58.61 - Equipment design.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 1 2011-04-01 2011-04-01 false Equipment design. 58.61 Section 58.61 Food and... PRACTICE FOR NONCLINICAL LABORATORY STUDIES Equipment § 58.61 Equipment design. Equipment used in the... of appropriate design and adequate capacity to function according to the protocol and shall be...

Action Biology. Advanced Placement for the Second Year. First Edition.

ERIC Educational Resources Information Center

Davis, Mary Pitt

This document provides biology experiments designed for students who have completed a first year biology course. This self contained laboratory booklet contains four sections. In section 1, "Instrumentation in the Study of Cells," discussion sections and suggestions for teacher demonstrations are provided. It also includes some basic materials…

The Energy Primer.

ERIC Educational Resources Information Center

Tennessee Valley Authority, Chattanooga. Div. of Power Utilization.

This publication is an information source on energy for teachers. The information in this publication is factual, and designed for courses of study about energy. This book has been divided into separate energy-related sections. Each section ends with a list of student participation discussion activities. The sections present facts about: (1)…

Evaluating the Cooperative Component in Cooperative Learning: A Quasi-Experimental Study

ERIC Educational Resources Information Center

Emerson, Tisha L. N.; English, Linda K.; McGoldrick, KimMarie

2015-01-01

In this study, the authors employed a quasi-experimental research design to examine the efficacy of a cooperative learning pedagogy (i.e., think-pair-share exercises) integrated into sections of microeconomic principles. Materials, exercises, and assessment instruments for all study sections are identical except for the nature of the…

National Dam Safety Program. Cadet Mine Tailings Dam (MO 30715), Mississippi - Kaskaskia - St. Louis Basin, Washington County, Missouri. Phase I Inspection Report.

DTIC Science & Technology

1980-02-01

Safety Inspection of Dams" are not available. These studies should be performed by a professional engineer experienced in the design and construction...engineer experienced in the design and construction of tailings dams. An inspection and maintenance program should be initiated. Periodic inspections...Page No. SECTION 1 - PROJECT INFORMATION 1.1 General 1 1.2 Description of Project 1 1.3 Pertinent Data 2 SECTION 2 - ENGINEERING DATA 2.1 Design 5 2.2

Geostationary Operational Environmental Satellite (GOES-N report). Volume 1: Technical

NASA Technical Reports Server (NTRS)

1991-01-01

The GOES-N study consisted of five distinct tasks including: determining replication costs of GOES I-M and GOES-7 in the GOES-N time frame; defining and evaluating modifications to GOES I-M to improve efficiency or reduce costs; and defining evolutionary changes to the GOES I-M design to satisfy National Weather Service (NWS) 1983 and NOAA 1989 requirements. The categorization and disposition of NOAA requirements is reported in volume 1 section 4. Results of the GOES I-M efficiency/cost improvement modifications study are described in Section 7.1. The system concept options 1, 2, and 3 that generally represent the results of the Task 2, 3A, and 3B studies are summarized in Section 7.2. Another result of the GOES-N study, the determination of which NWS 1983 and NOAA 1989 requirements can be met with the three options, is contained in volume 1 section 7. Conclusions and recommendations are covered in volume 1 section 8. Imager, sounder, control system, space environment monitor, search and rescue, weather facsimile, data collection system, and products/process/communications recommendations were extracted from sections 9, 10, and 11. Section 8 also contains conclusions pertaining to programmatic operational satellite issues (prerequisite development strategies, the direct procurement of instruments by the government, protoflight mission, etc.). Sections 9, 10, and 11 address instrument, control system, image/navigation/registration, and other system design considerations and surveys. These sections are supported by the appendices in volume 2.

Geostationary Operational Environmental Satellite (GOES-N report). Volume 1: Technical

NASA Astrophysics Data System (ADS)

1991-12-01

The GOES-N study consisted of five distinct tasks including: determining replication costs of GOES I-M and GOES-7 in the GOES-N time frame; defining and evaluating modifications to GOES I-M to improve efficiency or reduce costs; and defining evolutionary changes to the GOES I-M design to satisfy National Weather Service (NWS) 1983 and NOAA 1989 requirements. The categorization and disposition of NOAA requirements is reported in volume 1 section 4. Results of the GOES I-M efficiency/cost improvement modifications study are described in Section 7.1. The system concept options 1, 2, and 3 that generally represent the results of the Task 2, 3A, and 3B studies are summarized in Section 7.2. Another result of the GOES-N study, the determination of which NWS 1983 and NOAA 1989 requirements can be met with the three options, is contained in volume 1 section 7. Conclusions and recommendations are covered in volume 1 section 8. Imager, sounder, control system, space environment monitor, search and rescue, weather facsimile, data collection system, and products/process/communications recommendations were extracted from sections 9, 10, and 11. Section 8 also contains conclusions pertaining to programmatic operational satellite issues (prerequisite development strategies, the direct procurement of instruments by the government, protoflight mission, etc.). Sections 9, 10, and 11 address instrument, control system, image/navigation/registration, and other system design considerations and surveys. These sections are supported by the appendices in volume 2.

Distributive Education II. Course of Study.

ERIC Educational Resources Information Center

Nelson, Frank W.

This curriculum guide for teacher-coordinators is designed to provide a course of study in distributive education (Distributive Education II) in Oklahoma. Content is in nine sections with each section consisting of one or more instructional units: (1) Orientation (Introduction to Distributive Occupations, DECA), (2) Survival Skills (Job…

A time projection chamber for high accuracy and precision fission cross-section measurements

DOE PAGES

Heffner, M.; Asner, D. M.; Baker, R. G.; ...

2014-05-22

The fission Time Projection Chamber (fissionTPC) is a compact (15 cm diameter) two-chamber MICROMEGAS TPC designed to make precision cross-section measurements of neutron-induced fission. The actinide targets are placed on the central cathode and irradiated with a neutron beam that passes axially through the TPC inducing fission in the target. The 4π acceptance for fission fragments and complete charged particle track reconstruction are powerful features of the fissionTPC which will be used to measure fission cross-sections and examine the associated systematic errors. This study provides a detailed description of the design requirements, the design solutions, and the initial performance ofmore » the fissionTPC.« less

Behaviour of Reinforced Concrete Columns of Various Cross-Sections Subjected to Fire

NASA Astrophysics Data System (ADS)

Balaji, Aneesha; Muhamed Luquman, K.; Nagarajan, Praveen; Madhavan Pillai, T. M.

2016-09-01

Fire resistance is one of the crucial design regulations which are now mandatory in most of the design codes. Therefore, a thorough knowledge of behaviour of structures exposed to fire is required in this aspect. Columns are the most vulnerable structural member to fire as it can be exposed to fire from all sides. However, the data available for fire resistant design for columns are limited. Hence the present work is focused on the effect of cross-sectional shape of column in fire resistance design. The various cross-sections considered are Square, Ell (L), Tee (T), and Plus (`+') shape. Also the effect of size and shape and distribution of steel reinforcement on fire resistance of columns is studied. As the procedure for determining fire resistance is not mentioned in Indian Standard code IS 456 (2000), the simplified method (500 °C isotherm method) recommended in EN 1992-1-2:2004 (E) (Eurocode 2) is adopted. The temperature profiles for various cross-sections are developed using finite element method and these profiles are used to predict fire resistance capability of compression members. The fire resistance based on both numerical and code based methods are evaluated and compared for various types of cross-section.

Alienation from School

ERIC Educational Resources Information Center

Hascher, Tina; Hagenauer, Gerda

2010-01-01

Two studies aimed at understanding the time course of alienation from school and school factors that may influence alienation from school during early adolescence. In Study 1, 434 students from grade 5-8 participated (cross-sectional design). In Study 2, we followed 356 students from grade 6-7 (longitudinal design). The results confirm the…

Supervisor Behaviours that Facilitate Training Transfer

ERIC Educational Resources Information Center

Lancaster, Sue; Di Milia, Lee; Cameron, Roslyn

2013-01-01

Purpose: The purpose of this paper is to describe the supervisor behaviours that employees found to be helpful and unhelpful in facilitating training transfer. The study aims to provide rich qualitative data from the employee's perspective. Design/methodology/approach: This study utilises a cross-sectional design. A case study and a qualitative…

Sample size calculations for stepped wedge and cluster randomised trials: a unified approach

PubMed Central

Hemming, Karla; Taljaard, Monica

2016-01-01

Objectives To clarify and illustrate sample size calculations for the cross-sectional stepped wedge cluster randomized trial (SW-CRT) and to present a simple approach for comparing the efficiencies of competing designs within a unified framework. Study Design and Setting We summarize design effects for the SW-CRT, the parallel cluster randomized trial (CRT), and the parallel cluster randomized trial with before and after observations (CRT-BA), assuming cross-sectional samples are selected over time. We present new formulas that enable trialists to determine the required cluster size for a given number of clusters. We illustrate by example how to implement the presented design effects and give practical guidance on the design of stepped wedge studies. Results For a fixed total cluster size, the choice of study design that provides the greatest power depends on the intracluster correlation coefficient (ICC) and the cluster size. When the ICC is small, the CRT tends to be more efficient; when the ICC is large, the SW-CRT tends to be more efficient and can serve as an alternative design when the CRT is an infeasible design. Conclusion Our unified approach allows trialists to easily compare the efficiencies of three competing designs to inform the decision about the most efficient design in a given scenario. PMID:26344808

Research design and statistical methods in Pakistan Journal of Medical Sciences (PJMS).

PubMed

Akhtar, Sohail; Shah, Syed Wadood Ali; Rafiq, M; Khan, Ajmal

2016-01-01

This article compares the study design and statistical methods used in 2005, 2010 and 2015 of Pakistan Journal of Medical Sciences (PJMS). Only original articles of PJMS were considered for the analysis. The articles were carefully reviewed for statistical methods and designs, and then recorded accordingly. The frequency of each statistical method and research design was estimated and compared with previous years. A total of 429 articles were evaluated (n=74 in 2005, n=179 in 2010, n=176 in 2015) in which 171 (40%) were cross-sectional and 116 (27%) were prospective study designs. A verity of statistical methods were found in the analysis. The most frequent methods include: descriptive statistics (n=315, 73.4%), chi-square/Fisher's exact tests (n=205, 47.8%) and student t-test (n=186, 43.4%). There was a significant increase in the use of statistical methods over time period: t-test, chi-square/Fisher's exact test, logistic regression, epidemiological statistics, and non-parametric tests. This study shows that a diverse variety of statistical methods have been used in the research articles of PJMS and frequency improved from 2005 to 2015. However, descriptive statistics was the most frequent method of statistical analysis in the published articles while cross-sectional study design was common study design.

[Saarland Growth Study: sampling design].

PubMed

Danker-Hopfe, H; Zabransky, S

2000-01-01

The use of reference data to evaluate the physical development of children and adolescents is part of the daily routine in the paediatric ambulance. The construction of such reference data is based on the collection of extensive reference data. There are different kinds of reference data: cross sectional references, which are based on data collected from a big representative cross-sectional sample of the population, longitudinal references, which are based on follow-up surveys of usually smaller samples of individuals from birth to maturity, and mixed longitudinal references, which are a combination of longitudinal and cross-sectional reference data. The advantages and disadvantages of the different methods of data collection and the resulting reference data are discussed. The Saarland Growth Study was conducted for several reasons: growth processes are subject to secular changes, there are no specific reference data for children and adolescents from this part of the country and the growth charts in use in the paediatric praxis are possibly not appropriate any more. Therefore, the Saarland Growth Study served two purposes a) to create actual regional reference data and b) to create a database for future studies on secular trends in growth processes of children and adolescents from Saarland. The present contribution focusses on general remarks on the sampling design of (cross-sectional) growth surveys and its inferences for the design of the present study.

Energy transport corridors: the potential role of Federal lands in states identified by the Energy Policy Act of 2005, section 368(b).

DOE Office of Scientific and Technical Information (OSTI.GOV)

Krummel, J.; Hlohowskyj, I.; Kuiper, J.

2011-09-01

On August 8, 2005, the President signed the Energy Policy Act of 2005 (EPAct) into law. In Subtitle F of EPAct, Congress set forth various provisions that would change the way certain federal agencies (Agencies) coordinate to authorize the use of land for a variety of energy-related purposes. As part of Subtitle F of EPAct, Section 368 addresses the issue of energy transportation corridors on federal land for oil, gas, and hydrogen pipelines, as well as electricity transmission and distribution facilities. Because of the critical importance of improving the nation's electrical transmission grid, Congress recognized that electricity transmission issues shouldmore » receive added attention when the Agencies address corridor location and analysis issues. In Section 368, Congress specifically directed the Agencies to consider the need for upgraded and new facilities to deliver electricity: In carrying out [Section 368], the Secretaries shall take into account the need for upgraded and new electricity transmission and distribution facilities to (1) improve reliability; (2) relieve congestion; and (3) enhance capability of the national grid to deliver electricity. Section 368 does not require the Agencies to consider or approve specific projects, applications for rights-of-way (ROWs), or other permits within designated energy corridors. Importantly, Section 368 does not direct, license, or otherwise permit any on-the-ground activity of any sort. If an applicant is interested in obtaining an authorization to develop a project within any corridor designated under Section 368, the applicant would have to apply for a ROW authorization and applicable permits. The Agencies would consider each application by applying appropriate project-specific reviews under requirements of laws and related regulations, including, but not limited to, the National Environmental Policy Act (NEPA), the Clean Water Act, the Clean Air Act, Section 7 of the Endangered Species Act (ESA), and Section 106 of the National Historic Preservation Act (NHPA). Under Section 368, Congress divided the United States into two groups of states: the 11 contiguous western states and the remaining states. Direction for energy transportation corridor analysis and selection in the 11 western states was addressed in Section 368(a) of EPAct, while direction for energy transportation corridor analysis and selection in all other states was addressed under Section 368(b) of EPAct. It was clearly the priority of Congress to conduct corridor location studies and designation first on federal lands in the western states. Under Section 368(a), the Agencies produced a programmatic environmental impact statement (EIS), Designation of Energy Corridors on Federal Land in the 11 Western States (DOE and DOI 2008), that was used in part as the basis for designating more than 6,000 mi (9,656 km) of energy transportation corridors on federal land in 11 western states. Under Section 368(a) of EPAct, Congress clearly stated the Agencies needed to (1) designate energy transportation corridors on federal land, (2) conduct the necessary environmental review of the designated corridors, and (3) incorporate the designated corridors into the appropriate land use plans. Congressional direction under Section 368(b) of EPAct differs from that provided under Section 368(a). Specifically, Section 368(b) requires the secretaries of the Agencies, in consultation with the Federal Energy Regulatory Commission (FERC), affected utility industries, and other interested persons, to jointly: (1) Identify corridors for oil, gas, and hydrogen pipelines and electricity transmission and distribution facilities on federal land in states other than the 11 western states identified under Section 368(a) of EPAct, and (2) Schedule prompt action to identify, designate, and incorporate the corridors into the applicable land use plans. While Section 368(a) clearly directs designation as a necessary first step for energy transportation corridors in the 11 western states, Section 368(b) directs the Agencies to first identify corridors and then schedule prompt action to identify, designate, and incorporate the corridors into applicable land use plans. To comply with the congressional direction provided in Section 368(b), the Agencies investigated corridor identification issues in the Section 368(b) states; this report to Congress provides information that could be relevant to possible future designation of energy corridors. Future designations, if appropriate and necessary, would occur when the Agencies undertake revisions and/or updates to land use plans that guide management decisions on lands located within individual administrative units, such as specific National Forests, National Parks, or Wildlife Refuges. At this time, the Agencies are not proposing any actions or decisions related directly or indirectly to designating energy corridors on federal land under Section 368(b) of EPAct.« less

23 CFR Appendix C to Subpart A of... - Policy for the Signing and Numbering of Future Interstate Corridors Designated by Section 332 of...

Code of Federal Regulations, 2014 CFR

2014-04-01

... Interstate Corridors Designated by Section 332 of the NHS Designation Act of 1995 or Designated Under 23 U.S... Interstate Corridors Designated by Section 332 of the NHS Designation Act of 1995 or Designated Under 23 U.S... signs along a federally designated future Interstate corridor only after the specific route location has...

23 CFR Appendix C to Subpart A of... - Policy for the Signing and Numbering of Future Interstate Corridors Designated by Section 332 of...

Code of Federal Regulations, 2011 CFR

2011-04-01

... Interstate Corridors Designated by Section 332 of the NHS Designation Act of 1995 or Designated Under 23 U.S... Interstate Corridors Designated by Section 332 of the NHS Designation Act of 1995 or Designated Under 23 U.S... signs along a federally designated future Interstate corridor only after the specific route location has...

23 CFR Appendix C to Subpart A of... - Policy for the Signing and Numbering of Future Interstate Corridors Designated by Section 332 of...

Code of Federal Regulations, 2013 CFR

2013-04-01

... Interstate Corridors Designated by Section 332 of the NHS Designation Act of 1995 or Designated Under 23 U.S... Interstate Corridors Designated by Section 332 of the NHS Designation Act of 1995 or Designated Under 23 U.S... signs along a federally designated future Interstate corridor only after the specific route location has...

23 CFR Appendix C to Subpart A of... - Policy for the Signing and Numbering of Future Interstate Corridors Designated by Section 332 of...

Code of Federal Regulations, 2010 CFR

2010-04-01

... Interstate Corridors Designated by Section 332 of the NHS Designation Act of 1995 or Designated Under 23 U.S... Corridors Designated by Section 332 of the NHS Designation Act of 1995 or Designated Under 23 U.S.C. 139(b... federally designated future Interstate corridor only after the specific route location has been established...

In Search of Canadian Materials, Revised.

ERIC Educational Resources Information Center

Phillips, Donna, Comp.

Designed as an aid to the selection of Canadian materials for the school library, this revised edition lists 2,100 titles and provides a new separate section on women's studies. Major subdivisions of the work include periodical and reference materials sections, as well as sections by subject category: business and consumer education; fine arts,…

Enhancing Student Learning of Research Methods through the Use of Undergraduate Teaching Assistants

ERIC Educational Resources Information Center

Crowe, Jessica; Ceresola, Ryan; Silva, Tony

2014-01-01

By using a quasi-experimental design, in this study, we test the effect of undergraduate teaching assistants on student learning. Data were collected from 170 students enrolled in four sections of a quantitative research methods course, two sections without undergraduate teaching assistants and two sections with undergraduate teaching assistants,…

Comparison of safety effect estimates obtained from empirical Bayes before-after study, propensity scores-potential outcomes framework, and regression model with cross-sectional data.

PubMed

Wood, Jonathan S; Donnell, Eric T; Porter, Richard J

2015-02-01

A variety of different study designs and analysis methods have been used to evaluate the performance of traffic safety countermeasures. The most common study designs and methods include observational before-after studies using the empirical Bayes method and cross-sectional studies using regression models. The propensity scores-potential outcomes framework has recently been proposed as an alternative traffic safety countermeasure evaluation method to address the challenges associated with selection biases that can be part of cross-sectional studies. Crash modification factors derived from the application of all three methods have not yet been compared. This paper compares the results of retrospective, observational evaluations of a traffic safety countermeasure using both before-after and cross-sectional study designs. The paper describes the strengths and limitations of each method, focusing primarily on how each addresses site selection bias, which is a common issue in observational safety studies. The Safety Edge paving technique, which seeks to mitigate crashes related to roadway departure events, is the countermeasure used in the present study to compare the alternative evaluation methods. The results indicated that all three methods yielded results that were consistent with each other and with previous research. The empirical Bayes results had the smallest standard errors. It is concluded that the propensity scores with potential outcomes framework is a viable alternative analysis method to the empirical Bayes before-after study. It should be considered whenever a before-after study is not possible or practical. Copyright © 2014 Elsevier Ltd. All rights reserved.

Adolescent Idiopathic Scoliosis and Eating Disorders: Is There a Relation? Results of a Cross-Sectional Study

ERIC Educational Resources Information Center

Zaina, Fabio; Donzelli, Sabrina; Lusini, Monia; Vismara, Luca; Capodaglio, Paolo; Neri, Laura; Negrini, Stefano

2013-01-01

A recent study suggests a correlation between idiopathic scoliosis in adolescence and eating disorders. However, this does not correspond with our clinical experience in the same population. The aim of this study was to verify the correlation between scoliosis and eating disorders in adolescence. A cross-sectional study was designed including 187…

Design of Test Loops for Forced Convection Heat Transfer Studies at Supercritical State

NASA Astrophysics Data System (ADS)

Balouch, Masih N.

Worldwide research is being conducted to improve the efficiency of nuclear power plants by using supercritical water (SCW) as the working fluid. One such SCW reactor considered for future development is the CANDU-Supercritical Water Reactor (CANDU-SCWR). For safe and accurate design of the CANDU-SCWR, a detailed knowledge of forced-convection heat transfer in SCW is required. For this purpose, two supercritical fluid loops, i.e. a SCW loop and an R-134a loop are developed at Carleton University. The SCW loop is designed to operate at pressures as high as 28 MPa, temperatures up to 600 °C and mass fluxes of up to 3000 kg/m2s. The R-134a loop is designed to operate at pressures as high as 6 MPa, temperatures up to 140 °C and mass fluxes in the range of 500-6000 kg/m2s. The test loops designs allow for up to 300 kW of heating power to be imparted to the fluid. Both test loops are of the closed-loop design, where flow circulation is achieved by a centrifugal pump in the SCW loop and three parallel-connected gear pumps in the R-134a loop, respectively. The test loops are pressurized using a high-pressure nitrogen cylinder and accumulator assembly, which allows independent control of the pressure, while simultaneously dampening pump induced pressure fluctuations. Heat exchangers located upstream of the pumps control the fluid temperature in the test loops. Strategically located measuring instrumentation provides information on the flow rate, pressure and temperature in the test loops. The test loops have been designed to accommodate a variety of test-section geometries, ranging from a straight circular tube to a seven-rod bundle, achieving heat fluxes up to 2.5 MW/m2 depending on the test-section geometry. The design of both test loops allows for easy reconfiguration of the test-section orientation relative to the gravitational direction. All the test sections are of the directly-heated design, where electric current passing through the pressure retaining walls of the test sections provides the Joule heating required to heat up the fluid to supercritical conditions. A high-temperature dielectric gasket isolates the current carrying parts of the test section from the rest of the assembly. Temperature and pressure drop data are collected at the inlet and outlet, and along the heated length of the test section. The test loops and test sections are designed according to American Society of Mechanical Engineers (ASME) Pressure Piping B31.1, and Boiler and Pressure Vessel Code, Section VIII-Division 1 rules. The final test loops and test sections assemblies are certified by Technical Standards and Safety Authority (TSSA). Every attempt is made to use off-the-shelf components where possible in order to streamline the design process and reduce costs. Following a rigorous selection process, stainless steel Types 316 and 316H are selected as the construction materials for the test loops, and Inconel 625 is selected as the construction material for the test sections. This thesis describes the design of the SCW and R-134a loops along with the three test-section geometries (i.e., tubular, annular and bundle designs).

Medical Students' Attitudes towards Peer Physical Examination: Findings from an International Cross-Sectional and Longitudinal Study

ERIC Educational Resources Information Center

Rees, Charlotte E.; Wearn, Andy M.; Vnuk, Anna K.; Sato, Toshio J.

2009-01-01

Although studies have begun to shed light on medical students' attitudes towards peer physical examination (PPE), they have been conducted at single sites, and have generally not examined changes in medical students' attitudes over time. Employing both cross-sectional and longitudinal designs, the current study examines medical students' attitudes…

Optimal one-section and two-section circular sound-absorbing duct liners for plane-wave and monopole sources without flow

NASA Technical Reports Server (NTRS)

Lester, H. C.; Posey, J. W.

1976-01-01

A discrete frequency study is made of the influence of source characteristics on the optimal properties of acoustically lined uniform and two section ducts. Two simplified sources, a plane wave and a monopole, are considered in some detail and over a greater frequency range than has been previously studied. Source and termination impedance effects are given limited examination. An example of a turbomachinery source and three associated source variants is also presented. Optimal liner designs based on modal theory approach the Cremer criterion at low frequencies and the geometric acoustics limit at high frequencies. Over an intermediate frequency range, optimal two section liners produced higher transmission losses than did the uniform configurations. Source distribution effects were found to have a significant effect on optimal liner design, but source and termination impedance effects appear to be relatively unimportant.

Estimating the Occurrence of Child Maltreatment and Risk-Factor Effects: Benefits of a Mixed-Design Strategy in Epidemiologic Research.

ERIC Educational Resources Information Center

Bertolli, Jeanne; And Others

1995-01-01

This article discusses methodologic limitations of four observational study designs (ecologic, case-control, cross-sectional, and cohort) that dominate the child abuse and neglect literature and identifies key features of an "ideal" study of child maltreatment. It proposes a new mixed-design strategy, which improves ability to identify child…

Detailed design package for design of a video system providing optimal visual information for controlling payload and experiment operations with television

NASA Technical Reports Server (NTRS)

1975-01-01

A detailed description of a video system for controlling space shuttle payloads and experiments is presented in the preliminary design review and critical design review, first and second engineering design reports respectively, and in the final report submitted jointly with the design package. The material contained in the four subsequent sections of the package contains system descriptions, design data, and specifications for the recommended 2-view system. Section 2 contains diagrams relating to the simulation test configuration of the 2-view system. Section 3 contains descriptions and drawings of the deliverable breadboard equipment. A description of the recommended system is contained in Section 4 with equipment specifications in Section 5.

High-Fidelity Multidisciplinary Design Using an Integrated Design Environment

DTIC Science & Technology

2007-08-14

Leovirivakit and A. .Jamneson, -- Case Studies ini Aero-St ruc(t ural NWing Planiforiii aiid Section Op- tifiization". 22`1~ AIAA Applied Aerodynamaiics...design of complete aircraft configurations. The work was focused on four main areas: (1) Flow solution algorithms for unstructured meshes, (2) Aero...Multi-Fidelity Design Optimization Studies for Supersonic lIets" . 13"’" AIAA Aerospace Sciences Meeting kc E’xhibit, AIAA Paper 2005- (0531, Reno. NV

Assessment of optimum threshold and particle shape parameter for the image analysis of aggregate size distribution of concrete sections

NASA Astrophysics Data System (ADS)

Ozen, Murat; Guler, Murat

2014-02-01

Aggregate gradation is one of the key design parameters affecting the workability and strength properties of concrete mixtures. Estimating aggregate gradation from hardened concrete samples can offer valuable insights into the quality of mixtures in terms of the degree of segregation and the amount of deviation from the specified gradation limits. In this study, a methodology is introduced to determine the particle size distribution of aggregates from 2D cross sectional images of concrete samples. The samples used in the study were fabricated from six mix designs by varying the aggregate gradation, aggregate source and maximum aggregate size with five replicates of each design combination. Each sample was cut into three pieces using a diamond saw and then scanned to obtain the cross sectional images using a desktop flatbed scanner. An algorithm is proposed to determine the optimum threshold for the image analysis of the cross sections. A procedure was also suggested to determine a suitable particle shape parameter to be used in the analysis of aggregate size distribution within each cross section. Results of analyses indicated that the optimum threshold hence the pixel distribution functions may be different even for the cross sections of an identical concrete sample. Besides, the maximum ferret diameter is the most suitable shape parameter to estimate the size distribution of aggregates when computed based on the diagonal sieve opening. The outcome of this study can be of practical value for the practitioners to evaluate concrete in terms of the degree of segregation and the bounds of mixture's gradation achieved during manufacturing.

21 CFR 320.27 - Guidelines on the design of a multiple-dose in vivo bioavailability study.

Code of Federal Regulations, 2011 CFR

2011-04-01

... vivo bioavailability study. 320.27 Section 320.27 Food and Drugs FOOD AND DRUG ADMINISTRATION... Guidelines on the design of a multiple-dose in vivo bioavailability study. (a) Basic principles. (1) In... labeling of the test product. (3) A multiple-dose study may be required to determine the bioavailability of...

Comparison of Student Performance in Video Game Format vs. Traditional Approach in Introductory Astronomy Classes

NASA Astrophysics Data System (ADS)

Barringer, Daniel; Kregenow, Julia M.; Palma, Christopher; Plummer, Julia

2015-01-01

In Spring of 2014, Penn State debuted an online Introductory Astronomy (AST 001) section that was designed as a video game. Previous studies have shown that well-designed games help learners to build accurate understanding of embedded concepts and processes and aid learner motivation, which strongly contributes to a student's willingness to learn. We start by presenting the learning gains as measured with the Test of Astronomy Standards (TOAST) from this new course design. We further compare the learning gains from the video game section with learning gains measured from more traditional online formats and in-person lecture sections of AST 001 taught at Penn State over the last five years to evaluate the extent to which this new medium for online Astronomy education supports student learning.

78 FR 49520 - Scientific Information Request on Imaging Techniques for the Surveillance, Diagnosis, and Staging...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-14

... conducting this comparative effectiveness review pursuant to Section 1013 of the Medicare Prescription Drug... summary, including the following elements: study number, study period, design, methodology, indication and... period, design, methodology, indication and diagnosis, proper use instructions, inclusion and exclusion...

Design and evaluation of steel bridges with double composite action

DOT National Transportation Integrated Search

2010-02-01

This report presents findings from a cooperative USF/URS/FDOT research study undertaken to develop design rules for : double composite steel bridges. In the study, a 48 ft long, 16 ft wide, 4 ft. 10 in. deep trapezoidal HPS 70W box section : desig...

Satellite Power Systems (SPS) concept definition study, exhibit C. Volume 2, part 1: System engineering

NASA Technical Reports Server (NTRS)

Hanley, G. M.

1979-01-01

Volume 2, Part 1, of a seven volume report is presented. Part 1 encompasses Satellite Power Systems (SPS) systems engineering aspects and is divided into three sections. The first section presents descriptions of the various candidate concepts considered and conclusions and recommendations for a preferred concept. The second section presents a summary of results of the various trade studies and analysis conducted during the course of the study. The third section describes the Photovoltaic Satellite Based Satellite Power System (SPS) Point Design as it was defined through studies performed during the period January 1977 through March 1979.

The World Around Them; Environmental Education in the Urban Environment.

ERIC Educational Resources Information Center

Henderson, Ernest L.

This manual is a teacher's guide to environmental study activities for intermediate grade students in urban areas. It is divided into four color coded sections: A City Block-An Environmental Design; The Streets of the City; Noise Pollution; and Student Worksheets and Study Guides. Each of these sections presents objectives, generalizations, and…

Future Studies in the K-12 Curriculum.

ERIC Educational Resources Information Center

Haas, John D.

This guide is designed to help elementary and secondary school teachers and curriculum developers plan units on the future. It is presented in five sections. Section I discusses the origins of the modern futures movement and the concepts of future studies, time dimensions, global approach, self-fulfilling and self-defeating forecasts, and types of…

Flipped Instruction in a High School Science Classroom

ERIC Educational Resources Information Center

Leo, Jonathan; Puzio, Kelly

2016-01-01

This paper reports on a quasi-experimental study examining the effectiveness of flipped instruction in a 9th grade biology classroom. This study included four sections of freshmen-level biology taught by the first author at a private secondary school in the Pacific Northwest. Using a block randomized design, two sections were flipped and two…

End-of-High-School Mathematics Attainment: How Did Students Get There?

ERIC Educational Resources Information Center

Newton, Xiaoxia A.

2010-01-01

Background: Many studies have looked at students' mathematics achievement in the middle and high school years and the kinds of factors that are associated with their achievement. Within this domain, however, most research utilized cross-sectional data. Cross-sectional designs have both statistical and conceptual limitations. Few studies used…

75 FR 51328 - Agency Information Collection Activities: Request for Comments for a New Information Collection

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-19

... National Transportation Systems Center (Volpe Center) have designed the survey and will submit the survey... Phase 2 Implementation Study Survey. The Federal Register notice with a 60-day public comment period...-LU Section 6009 Phase 2 Implementation Study Survey. Background: Section 6009 of the Safe...

Quantifying fish habitat associated with stream simulation design culverts in northern Wisconsin

Treesearch

A. Timm; D. Higgins; J. Stanovick; R. Kolka; S. Eggert

2017-01-01

This study investigated the effects of culvert replacement design on fish habitat and fish weight by comparing substrate diversity and weight at three stream simulation (SS)-design and three bankfull and backwater (BB)-design sites on the Chequamegon-Nicolet National Forest, Wisconsin. Stream channel cross-sections, Wolman substrate particle counts, and single-pass...

CMOS-array design-automation techniques

NASA Technical Reports Server (NTRS)

Feller, A.; Lombardt, T.

1979-01-01

Thirty four page report discusses design of 4,096-bit complementary metal oxide semiconductor (CMOS) read-only memory (ROM). CMOSROM is either mask or laser programable. Report is divided into six sections; section one describes background of ROM chips; section two presents design goals for chip; section three discusses chip implementation and chip statistics; conclusions and recommendations are given in sections four thru six.

Unit cell geometry of multiaxial preforms for structural composites

NASA Technical Reports Server (NTRS)

Ko, Frank; Lei, Charles; Rahman, Anisur; Du, G. W.; Cai, Yun-Jia

1993-01-01

The objective of this study is to investigate the yarn geometry of multiaxial preforms. The importance of multiaxial preforms for structural composites is well recognized by the industry but, to exploit their full potential, engineering design rules must be established. This study is a step in that direction. In this work the preform geometry for knitted and braided preforms was studied by making a range of well designed samples and studying them by photo microscopy. The structural geometry of the preforms is related to the processing parameters. Based on solid modeling and B-spline methodology a software package is developed. This computer code enables real time structural representations of complex fiber architecture based on the rule of preform manufacturing. The code has the capability of zooming and section plotting. These capabilities provide a powerful means to study the effect of processing variables on the preform geometry. the code also can be extended to an auto mesh generator for downstream structural analysis using finite element method. This report is organized into six sections. In the first section the scope and background of this work is elaborated. In section two the unit cell geometries of braided and multi-axial warp knitted preforms is discussed. The theoretical frame work of yarn path modeling and solid modeling is presented in section three. The thin section microscopy carried out to observe the structural geometry of the preforms is the subject in section four. The structural geometry is related to the processing parameters in section five. Section six documents the implementation of the modeling techniques into the computer code MP-CAD. A user manual for the software is also presented here. The source codes and published papers are listed in the Appendices.

Impact evaluation of composite floor sections

NASA Technical Reports Server (NTRS)

Boitnott, Richard L.; Fasanella, Edwin L.

1989-01-01

Graphite-epoxy floor sections representative of aircraft fuselage construction were statically and dynamically tested to evaluate their response to crash loadings. These floor sections were fabricated using a frame-stringer design typical of present aluminum aircraft without features to enhance crashworthiness. The floor sections were tested as part of a systematic research program developed to study the impact response of composite components of increasing complexity. The ultimate goal of the research program is to develop crashworthy design features for future composite aircraft. Initially, individual frames of six-foot diameter were tested both statically and dynamically. The frames were then used to construct built-up floor sections for dynamic tests at impact velocities of approximately 20 feet/sec to simulate survivable crash velocities. In addition, static tests were conducted to gain a better understanding of the failure mechanisms seen in the dynamic tests.

The People of West Africa.

ERIC Educational Resources Information Center

Adams, George; And Others

Designed for use in Michigan schools, this K-2 social studies unit examines aspects of African and Black American life. Material is divided into 11 sections. Sections 1 and 2 provide rationale, project overview, and an introduction to the unit. Section 3 outlines the five content and skill goals of the program: to learn the location of Ghana,…

Space-Based Space Surveillance Logistics Case Study: A Qualitative Product Support Element Analysis

DTIC Science & Technology

2017-12-01

Facilities and Infrastructure. Product Support Management and Design Interface are also covered, but only in a general manner. Conclusions from the study...core analysis, with the overarching two elements ( Design Interface and Product Support Management) mentioned briefly. G. THESIS STATEMENT This...were implemented. The two overarching elements of Product Support Management and Design Interface will be discussed briefly in the findings section

Analysis and design of quiet hypersonic wind tunnels

NASA Astrophysics Data System (ADS)

Naiman, Hadassah

The purpose of the present work is to integrate CFD into the design of quiet hypersonic wind tunnels and the analysis of their performance. Two specific problems are considered. The first problem is the automated design of the supersonic portion of a quiet hypersonic wind tunnel. Modern optimization software is combined with full Navier-Stokes simulations and PSE stability analysis to design a Mach 6 nozzle with maximum quiet test length. A response surface is constructed from a user-specified set of contour shapes and a genetic algorithm is used to find the "optimal contour", which is defined as the shortest nozzle with the maximum quiet test length. This is achieved by delaying transition along the nozzle wall. It is found that transition is triggered by Goertler waves, which can be suppressed by including a section of convex curvature along the contour. The optimal design has an unconventional shape described as compound curvature, which makes the contour appear slightly wavy. The second problem is the evaluation of a proposed modification of the test section in the Boeing/AFOSR Mach 6 Quiet Tunnel. The new design incorporates a section of increased diameter with the intention of enabling the tunnel to start in the presence of larger blunt models. Cone models with fixed base diameter (and hence fixed blockage ratio) are selected for this study. Cone half-angles from 15° to 75° are examined to ascertain the effect of ii the strength of the test model shock wave on the tunnel startup. The unsteady, laminar, compressible Navier-Stokes equations are solved. The resulting flowfields are analyzed to see what affect the shocks and shear layers have on the quiet test section flow. This study indicates that cone angles ≤20° allow the tunnel to start. Keywords. automated optimization, response surface, parabolized stability equations, compound curvature, laminar, wind tunnel, unstart, test section.

The Causal Effects of Father Absence

PubMed Central

McLanahan, Sara; Tach, Laura; Schneider, Daniel

2014-01-01

The literature on father absence is frequently criticized for its use of cross-sectional data and methods that fail to take account of possible omitted variable bias and reverse causality. We review studies that have responded to this critique by employing a variety of innovative research designs to identify the causal effect of father absence, including studies using lagged dependent variable models, growth curve models, individual fixed effects models, sibling fixed effects models, natural experiments, and propensity score matching models. Our assessment is that studies using more rigorous designs continue to find negative effects of father absence on offspring well-being, although the magnitude of these effects is smaller than what is found using traditional cross-sectional designs. The evidence is strongest and most consistent for outcomes such as high school graduation, children’s social-emotional adjustment, and adult mental health. PMID:24489431

Association between Lifestyle and School Attendance in Japanese Medical Students: A Pilot Study

ERIC Educational Resources Information Center

Tanaka, Masaaki; Watanabe, Yasuyoshi

2012-01-01

Objective: Lifestyle factors are thought to be associated with students' academic performance. Whether lifestyle factors were associated with medical students' school attendance was determined. Design: Cross-sectional design. Setting: The study group consisted of 157 healthy second-year medical students attending Osaka City University Graduate…

A Population-Based Study of Preschoolers' Food Neophobia and Its Associations with Food Preferences

ERIC Educational Resources Information Center

Russell, Catherine Georgina; Worsley, Anthony

2008-01-01

Objective: This cross-sectional study was designed to investigate the relationships between food preferences, food neophobia, and children's characteristics among a population-based sample of preschoolers. Design: A parent-report questionnaire. Setting: Child-care centers, kindergartens, playgroups, day nurseries, and swimming centers. Subjects:…

Domestic Violence Assessments in the Child Advocacy Center

ERIC Educational Resources Information Center

Thackeray, Jonathan D.; Scribano, Philip V.; Rhoda, Dale

2010-01-01

Objective: This study was designed to identify the frequency, methods, and practices of universal assessments for domestic violence (DV) within child advocacy centers (CACs) and determine which factors are associated with CACs that conduct universal DV assessments. Methods: The study design was a cross-sectional, web-based survey distributed to…

A design methodology for portable software on parallel computers

NASA Technical Reports Server (NTRS)

Nicol, David M.; Miller, Keith W.; Chrisman, Dan A.

1993-01-01

This final report for research that was supported by grant number NAG-1-995 documents our progress in addressing two difficulties in parallel programming. The first difficulty is developing software that will execute quickly on a parallel computer. The second difficulty is transporting software between dissimilar parallel computers. In general, we expect that more hardware-specific information will be included in software designs for parallel computers than in designs for sequential computers. This inclusion is an instance of portability being sacrificed for high performance. New parallel computers are being introduced frequently. Trying to keep one's software on the current high performance hardware, a software developer almost continually faces yet another expensive software transportation. The problem of the proposed research is to create a design methodology that helps designers to more precisely control both portability and hardware-specific programming details. The proposed research emphasizes programming for scientific applications. We completed our study of the parallelizability of a subsystem of the NASA Earth Radiation Budget Experiment (ERBE) data processing system. This work is summarized in section two. A more detailed description is provided in Appendix A ('Programming Practices to Support Eventual Parallelism'). Mr. Chrisman, a graduate student, wrote and successfully defended a Ph.D. dissertation proposal which describes our research associated with the issues of software portability and high performance. The list of research tasks are specified in the proposal. The proposal 'A Design Methodology for Portable Software on Parallel Computers' is summarized in section three and is provided in its entirety in Appendix B. We are currently studying a proposed subsystem of the NASA Clouds and the Earth's Radiant Energy System (CERES) data processing system. This software is the proof-of-concept for the Ph.D. dissertation. We have implemented and measured the performance of a portion of this subsystem on the Intel iPSC/2 parallel computer. These results are provided in section four. Our future work is summarized in section five, our acknowledgements are stated in section six, and references for published papers associated with NAG-1-995 are provided in section seven.

The Influence of Collaborative Learning on Student Attitudes and Performance in an Introductory Chemistry Laboratory

NASA Astrophysics Data System (ADS)

Shibley, Ivan A., Jr.; Zimmaro, Dawn M.

2002-06-01

This study was designed to determine the effect of collaborative learning on student attitudes and performance in an introductory chemistry laboratory. Two sections per semester for three semesters were randomly designated as either a control section or an experimental section. Students in the control section performed most labs individually, while those in the experimental section performed all labs in groups of four. Both quantitative and qualitative measures were used to evaluate the impact of collaborative learning on student achievement and attitudes. Grades did not differ between the two sections, indicating that collaborative learning did not affect short-term student achievement. Students seemed to develop a more positive attitude about the laboratory and about chemistry in the collaborative learning sections as judged from their classroom evaluations of the teacher, the course, and the collaborative learning experience. The use of collaborative learning in the laboratory as described in this paper therefore may provide a means of improving student attitudes toward chemistry.

Design of Deflectors for Little Goose Spillway, Snake River, Oregon: A Physical Model Study

DTIC Science & Technology

2017-06-01

model of the spillway. Four different deflector designs were compared relative to flow conditions in the stilling basin and tailrace area of the...performance in a 1:40-scale section model of the spillway. Four different deflector designs were compared relative to flow conditions in the stilling basin and...ER D C/ CH L TR -1 7- 10 Dissolved Gas Abatement Studies Design of Deflectors for Little Goose Spillway, Snake River, Oregon A

Research design and statistical methods in Pakistan Journal of Medical Sciences (PJMS)

PubMed Central

Akhtar, Sohail; Shah, Syed Wadood Ali; Rafiq, M.; Khan, Ajmal

2016-01-01

Objective: This article compares the study design and statistical methods used in 2005, 2010 and 2015 of Pakistan Journal of Medical Sciences (PJMS). Methods: Only original articles of PJMS were considered for the analysis. The articles were carefully reviewed for statistical methods and designs, and then recorded accordingly. The frequency of each statistical method and research design was estimated and compared with previous years. Results: A total of 429 articles were evaluated (n=74 in 2005, n=179 in 2010, n=176 in 2015) in which 171 (40%) were cross-sectional and 116 (27%) were prospective study designs. A verity of statistical methods were found in the analysis. The most frequent methods include: descriptive statistics (n=315, 73.4%), chi-square/Fisher’s exact tests (n=205, 47.8%) and student t-test (n=186, 43.4%). There was a significant increase in the use of statistical methods over time period: t-test, chi-square/Fisher’s exact test, logistic regression, epidemiological statistics, and non-parametric tests. Conclusion: This study shows that a diverse variety of statistical methods have been used in the research articles of PJMS and frequency improved from 2005 to 2015. However, descriptive statistics was the most frequent method of statistical analysis in the published articles while cross-sectional study design was common study design. PMID:27022365

A method for the design of transonic flexible wings

NASA Technical Reports Server (NTRS)

Smith, Leigh Ann; Campbell, Richard L.

1990-01-01

Methodology was developed for designing airfoils and wings at transonic speeds which includes a technique that can account for static aeroelastic deflections. This procedure is capable of designing either supercritical or more conventional airfoil sections. Methods for including viscous effects are also illustrated and are shown to give accurate results. The methodology developed is an interactive system containing three major parts. A design module was developed which modifies airfoil sections to achieve a desired pressure distribution. This design module works in conjunction with an aerodynamic analysis module, which for this study is a small perturbation transonic flow code. Additionally, an aeroelastic module is included which determines the wing deformation due to the calculated aerodynamic loads. Because of the modular nature of the method, it can be easily coupled with any aerodynamic analysis code.

Academic and Family Conditions Associated with Intrinsic Academic Motivation in Japanese Medical Students: A Pilot Study

ERIC Educational Resources Information Center

Tanaka, Masaaki; Watanabea, Yasuyoshi

2012-01-01

Objective: Intrinsic academic motivation is one of the most important psychological concepts in education, and it is related to academic outcomes in medical students. This study examined the relationships between academic and family conditions and intrinsic academic motivation. Design: Cross-sectional design. Setting: The study group consisted of…

Design of catalytic monoliths for closed-cycle carbon dioxide lasers

NASA Technical Reports Server (NTRS)

Herz, R. K.; Guinn, K.; Goldblum, S.; Noskowski, E.

1989-01-01

Pulsed carbon dioxide (CO2) lasers have many applications in aeronautics, space research, weather monitoring and other areas. Full exploitation of the potential of these lasers in hampered by the dissociation of CO2 that occurs during laser operation. The development of closed-cycle CO2 lasers requires active CO-O2 recombination (CO oxidation) catalyst and design methods for implementation of catalysts in CO2 laser systems. A monolith catalyst section model and associated design computer program, LASCAT, are presented to assist in the design of a monolith catalyst section of a closed cycle CO2 laser system. Using LASCAT,the designer is able to specify a number of system parameters and determine the monolith section performance. Trade-offs between the catalyst activity, catalyst dimensions, monolith dimensions, pressure drop, O2 conversion, and other variables can be explored and adjusted to meet system design specifications. An introduction describes a typical closed-cycle CO2 system, and indicates some advantages of a closed cycle laser system over an open cycle system and some advantages of monolith support over other types of supports. The development and use of a monolith catalyst model is presented. The results of a design study and a discussion of general design rules are given.

Radar Cross Section Studies/Compact Range Research

NASA Technical Reports Server (NTRS)

Burnside, W. D.; Dominek, A. K.; Gupta, I. J.; Newman, E. H.; Pathak, P. H.; Peters, L., Jr.

1988-01-01

A summary is given of the achievements of NASA Grant NsG-1613 by Ohio State University from May 1, 1987 to April 30, 1988. The major topics covered are as follows: (1) electromagnetic scattering analysis; (2) indoor scattering measurement systems; (3) RCS control; (4) waveform processing techniques; (5) material scattering and design studies; (6) design and evaluation of design studies; and (7) antenna studies. Major progress has been made in each of these areas as verified by the numerous publications produced.

Augmented Cross-Sectional Studies with Abbreviated Follow-up for Estimating HIV Incidence

PubMed Central

Claggett, B.; Lagakos, S.W.; Wang, R.

2011-01-01

Summary Cross-sectional HIV incidence estimation based on a sensitive and less-sensitive test offers great advantages over the traditional cohort study. However, its use has been limited due to concerns about the false negative rate of the less-sensitive test, reflecting the phenomenon that some subjects may remain negative permanently on the less-sensitive test. Wang and Lagakos (2010) propose an augmented cross-sectional design which provides one way to estimate the size of the infected population who remain negative permanently and subsequently incorporate this information in the cross-sectional incidence estimator. In an augmented cross-sectional study, subjects who test negative on the less-sensitive test in the cross-sectional survey are followed forward for transition into the nonrecent state, at which time they would test positive on the less-sensitive test. However, considerable uncertainty exists regarding the appropriate length of follow-up and the size of the infected population who remain nonreactive permanently to the less-sensitive test. In this paper, we assess the impact of varying follow-up time on the resulting incidence estimators from an augmented cross-sectional study, evaluate the robustness of cross-sectional estimators to assumptions about the existence and the size of the subpopulation who will remain negative permanently, and propose a new estimator based on abbreviated follow-up time (AF). Compared to the original estimator from an augmented cross-sectional study, the AF Estimator allows shorter follow-up time and does not require estimation of the mean window period, defined as the average time between detectability of HIV infection with the sensitive and less-sensitive tests. It is shown to perform well in a wide range of settings. We discuss when the AF Estimator would be expected to perform well and offer design considerations for an augmented cross-sectional study with abbreviated follow-up. PMID:21668904

Augmented cross-sectional studies with abbreviated follow-up for estimating HIV incidence.

PubMed

Claggett, B; Lagakos, S W; Wang, R

2012-03-01

Cross-sectional HIV incidence estimation based on a sensitive and less-sensitive test offers great advantages over the traditional cohort study. However, its use has been limited due to concerns about the false negative rate of the less-sensitive test, reflecting the phenomenon that some subjects may remain negative permanently on the less-sensitive test. Wang and Lagakos (2010, Biometrics 66, 864-874) propose an augmented cross-sectional design that provides one way to estimate the size of the infected population who remain negative permanently and subsequently incorporate this information in the cross-sectional incidence estimator. In an augmented cross-sectional study, subjects who test negative on the less-sensitive test in the cross-sectional survey are followed forward for transition into the nonrecent state, at which time they would test positive on the less-sensitive test. However, considerable uncertainty exists regarding the appropriate length of follow-up and the size of the infected population who remain nonreactive permanently to the less-sensitive test. In this article, we assess the impact of varying follow-up time on the resulting incidence estimators from an augmented cross-sectional study, evaluate the robustness of cross-sectional estimators to assumptions about the existence and the size of the subpopulation who will remain negative permanently, and propose a new estimator based on abbreviated follow-up time (AF). Compared to the original estimator from an augmented cross-sectional study, the AF estimator allows shorter follow-up time and does not require estimation of the mean window period, defined as the average time between detectability of HIV infection with the sensitive and less-sensitive tests. It is shown to perform well in a wide range of settings. We discuss when the AF estimator would be expected to perform well and offer design considerations for an augmented cross-sectional study with abbreviated follow-up. © 2011, The International Biometric Society.

PBL and Critical Thinking Disposition in Chinese Medical Students--A Randomized Cross-Sectional Study

ERIC Educational Resources Information Center

Du, XiangYun; Emmersen, Jeppe; Toft, Egon; Sun, Baozhi

2013-01-01

The purpose of this study was to explore the relationship of problem-based learning (PBL) and the development of critical thinking disposition (CT) and academic achievement in Chinese medical students using a cross-sectional randomized design. Medical students from China Medical University (CMU) were randomized to PBL or non-PBL teaching at the…

Factors Associated with Women's Antenatal Plans to Use a Baby Walker: A Cross Sectional Study

ERIC Educational Resources Information Center

Illingworth, Rachel; Kendrick, Denise; Collier, Jacqueline; Woods, Amanda; Wattse, Kim; Dewey, Michael; Chen, Chih-Mei

2006-01-01

Objective: The objective of these analyses was to explore maternal antenatal decisions about baby walker use, factors associated with these decisions and the relationship between antenatal plans to use a walker and postnatal walker use. Design: Cross sectional study. Setting: Mothers-to-be (n = 1174) participating in a cluster randomised…

A Project-Based Cornerstone Course in Civil Engineering: Student Perceptions and Identity Development

ERIC Educational Resources Information Center

Marshall, Jill; Bhasin, Amit; Boyles, Stephen; David, Bernard; James, Rachel; Patrick, Anita

2018-01-01

Our study used a natural experiment to compare a project-based cornerstone course with the traditionally-taught introductory course in civil engineering. During the study, two sections of the course were organized around an overarching project, the design of an event center, and the remaining sections used guest lectures, a textbook, and…

In-Service Teachers' Perceptions and Interpretations of Students' Errors in Mathematics

ERIC Educational Resources Information Center

Chauraya, Million; Mashingaidze, Samuel

2017-01-01

This paper reports on findings of a research study that investigated in-service secondary school teachers' perceptions and interpretations of students' errors in mathematics. The study used a survey research design in which a questionnaire with two sections was used to collect data. The first section sought to find out the teachers' perceptions of…

Field investigation of high performance pavements in Virginia.

DOT National Transportation Integrated Search

2005-01-01

This study evaluated 18 pavement sections located in high-traffic highways in Virginia to find a premium pavement design with a life span of 40 years or more using current and past field experience. The selected pavement sections were thought to perf...

Preface to the special section on human factors and automation in vehicles: designing highly automated vehicles with the driver in mind.

PubMed

Merat, Natasha; Lee, John D

2012-10-01

This special section brings together diverse research regarding driver interaction with advanced automotive technology to guide design of increasingly automated vehicles. Rapidly evolving vehicle automation will likely change cars and trucks more in the next 5 years than the preceding 50, radically redefining what it means to drive. This special section includes 10 articles from European and North American researchers reporting simulator and naturalistic driving studies. Little research has considered the consequences of fully automated driving, with most focusing on lane-keeping and speed control systems individually. The studies reveal two underlying design philosophies: automate driving versus support driving. Results of several studies, consistent with previous research in other domains, suggest that the automate philosophy can delay driver responses to incidents in which the driver has to intervene and take control from the automation. Understanding how to orchestrate the transfer or sharing of control between the system and the driver, particularly in critical incidents, emerges as a central challenge. Designers should not assume that automation can substitute seamlessly for a human driver, nor can they assume that the driver can safely accommodate the limitations of automation. Designers, policy makers, and researchers must give careful consideration to what role the person should have in highly automated vehicles and how to support the driver if the driver is to be responsible for vehicle control. As in other domains, driving safety increasingly depends on the combined performance of the human and automation, and successful designs will depend on recognizing and supporting the new roles of the driver.

Reliability Based Geometric Design of Horizontal Circular Curves

NASA Astrophysics Data System (ADS)

Rajbongshi, Pabitra; Kalita, Kuldeep

2018-06-01

Geometric design of horizontal circular curve primarily involves with radius of the curve and stopping sight distance at the curve section. Minimum radius is decided based on lateral thrust exerted on the vehicles and the minimum stopping sight distance is provided to maintain the safety in longitudinal direction of vehicles. Available sight distance at site can be regulated by changing the radius and middle ordinate at the curve section. Both radius and sight distance depend on design speed. Speed of vehicles at any road section is a variable parameter and therefore, normally the 98th percentile speed is taken as the design speed. This work presents a probabilistic approach for evaluating stopping sight distance, considering the variability of all input parameters of sight distance. It is observed that the 98th percentile sight distance value is much lower than the sight distance corresponding to 98th percentile speed. The distribution of sight distance parameter is also studied and found to follow a lognormal distribution. Finally, the reliability based design charts are presented for both plain and hill regions, and considering the effect of lateral thrust.

Declining Fertility and the Use of Cesarean Delivery: Evidence from a Population-Based Study in Taiwan

PubMed Central

Ma, Ke-Zong M; Norton, Edward C; Lee, Shoou-Yih D

2010-01-01

Objective To test the hypothesis that declining fertility would affect the number of cesarean sections (c-sections) on maternal demand, but not medically indicated c-sections. Data Sources The 1996–2004 National Health Insurance Research Database in Taiwan for all singleton deliveries. Study Design Retrospective population-based, longitudinal study. Estimation was performed using multinomial probit models. Principal Findings Results revealed that declining fertility had a significant positive effect on the probability of having a c-section on maternal request but not medically indicated c-section. Conclusions Our findings offer a precautionary note to countries experiencing a fertility decline. Policies to contain the rise of c-sections should understand the role of women's preferences, especially regarding cesarean deliveries on maternal request. PMID:20545781

The Camera Lens: A Window into the [World]; Film Study and Film Making: Resource Suggestions for the English Class.

ERIC Educational Resources Information Center

Mihalka, Gwendolyn C.; Bolton, Gerre M.

This guide for film study and film making in the secondary English class arranges materials in a sequential order and divides them into four major sections. The section on background information includes: Table of Contents, Design for Use of the Guide, Rationale for the Use of Film Study in the English Class, Objectives for a Film Study and Film…

Big River Reservoir Project - Pawcatuck River and Narragansett Bay Drainage Basins - Water and Related Land Resources Study. Volume III. Appendices H-K.

DTIC Science & Technology

1981-07-01

including a recreation impact analysis, aquatic and terrestrial ecosystems assessment and a fish and wildlife management plan), social and cultural...APPENDIX G - DESIGN AND COST ESTIMATES VOLUME III - APPENDIX H - RECREATION AND NATURAL RESOURCES Section 1 - Recreation Impact Analysis Section 2 - Aquatic... Ecosystem Assessment Section 3 - Terrestrial Ecosystem Assessment Section 4 - Fish and Wildlife Management Plan APPENDIX I - SOCIAL AND CULTURAL

Composite Structure Modeling and Analysis of Advanced Aircraft Fuselage Concepts

NASA Technical Reports Server (NTRS)

Mukhopadhyay, Vivek; Sorokach, Michael R.

2015-01-01

NASA Environmentally Responsible Aviation (ERA) project and the Boeing Company are collabrating to advance the unitized damage arresting composite airframe technology with application to the Hybrid-Wing-Body (HWB) aircraft. The testing of a HWB fuselage section with Pultruded Rod Stitched Efficient Unitized Structure (PRSEUS) construction is presently being conducted at NASA Langley. Based on lessons learned from previous HWB structural design studies, improved finite-element models (FEM) of the HWB multi-bay and bulkhead assembly are developed to evaluate the performance of the PRSEUS construction. In order to assess the comparative weight reduction benefits of the PRSEUS technology, conventional cylindrical skin-stringer-frame models of a cylindrical and a double-bubble section fuselage concepts are developed. Stress analysis with design cabin-pressure load and scenario based case studies are conducted for design improvement in each case. Alternate analysis with stitched composite hat-stringers and C-frames are also presented, in addition to the foam-core sandwich frame and pultruded rod-stringer construction. The FEM structural stress, strain and weights are computed and compared for relative weight/strength benefit assessment. The structural analysis and specific weight comparison of these stitched composite advanced aircraft fuselage concepts demonstrated that the pressurized HWB fuselage section assembly can be structurally as efficient as the conventional cylindrical fuselage section with composite stringer-frame and PRSEUS construction, and significantly better than the conventional aluminum construction and the double-bubble section concept.

A Simple and Efficient Device for Demonstrating Cross-Sectional Anatomy of the Head

ERIC Educational Resources Information Center

Zamarioli, Ariane; Demaman, Aline Santos; Bim, Waldeci Roberto; Homem, Jefferson Mallman; Thomazini, Jose Antonio

2010-01-01

Described in this article is a novel device that facilitates study of the cross-sectional anatomy of the human head. In designing our device, we aimed to protect sections of the head from the destructive action of handling during anatomy laboratory while also ensuring excellent visualization of the anatomic structures. We used an electric saw to…

The Role of School Professionals in Implementing Section 504 for Students with Disabilities

ERIC Educational Resources Information Center

Madaus, Joseph W.; Shaw, Stan F.

2008-01-01

There is a paucity of research related to the implementation of the procedural regulations of Section 504 of the Rehabilitation Act of 1973 in public schools. Section 504 is a general education civil rights law designed to provide access for students with disabilities. This study presents data from a survey that was distributed to a range of…

Applications and Engineering Analysis of Lotus Roots under External Water Pressure

PubMed Central

Wang, Chang Jiang; Mynors, Diane

2016-01-01

Engineers can learn from nature for inspirations to create new designs. The internal structure of lotus roots with several oval holes was studied in this paper for engineering inspirations. The structural performance of lotus roots under outside water pressure was simulated and compared with various cross-sectional areas. The distribution of stresses in the cross-sectional area of lotus roots was analysed and presented. It was found that the maximum compressive stresses in the cross-sectional area of lotus roots were occurring at the long axis ends of the holes. This was very different from that of circular holes. Further analysis on the triaxiality factors revealed that the cross-sectional area of the lotus root resulted in large areas of high triaxiality factors. The resulting hydrostatic stress in the cross-sectional area of lotus root ranges from zero to 2.7 times the applied outside pressure. In contrast, the hydrostatic stress in a cylindrical cross-sectional area is a fixed value. The study showed that the lotus root and the orientation of the oval holes could be mimicked in the design of new structures, for example, underwater pipes and vessels. PMID:28127228

Impact of ambient air pollution on physical activity among adults: a systematic review and meta-analysis.

PubMed

An, Ruopeng; Zhang, Sheng; Ji, Mengmeng; Guan, Chenghua

2018-03-01

This study systematically reviewed literature regarding the impact of ambient air pollution on physical activity among children and adults. Keyword and reference search was conducted in PubMed and Web of Science to systematically identify articles meeting all of the following criteria - study designs: interventions or experiments, retrospective or prospective cohort studies, cross-sectional studies, and case-control studies; subjects: adults; exposures: specific air pollutants and overall air quality; outcomes: physical activity and sedentary behaviour; article types: peer-reviewed publications; and language: articles written in English. Meta-analysis was performed to estimate the pooled effect size of ambient PM 2.5 air pollution on physical inactivity. Seven studies met the inclusion criteria. Among them, six were conducted in the United States, and one was conducted in the United Kingdom. Six adopted a cross-sectional study design, and one used a prospective cohort design. Six had a sample size larger than 10,000. Specific air pollutants assessed included PM 2.5 , PM 10 , O 3 , and NO x , whereas two studies focused on overall air quality. All studies found air pollution level to be negatively associated with physical activity and positively associated with leisure-time physical inactivity. Study participants, and particularly those with respiratory disease, self-reported a reduction in outdoor activities to mitigate the detrimental impact of air pollution. Meta-analysis revealed a one unit (μg/m 3 ) increase in ambient PM 2.5 concentration to be associated with an increase in the odds of physical inactivity by 1.1% (odds ratio = 1.011; 95% confidence interval = 1.001, 1.021; p-value < .001) among US adults. Existing literature in general suggested that air pollution discouraged physical activity. Current literature predominantly adopted a cross-sectional design and focused on the United States. Future studies are warranted to implement a longitudinal study design and evaluate the impact of air pollution on physical activity in heavily polluted developing countries.

Asphaltic concrete overlays of rigid and flexible pavements : final report.

DOT National Transportation Integrated Search

1980-10-01

This study evaluated the effect of a given thickness of asphaltic concrete overlay in rehabilitating 53 test sections conforming to the experiment design. This factorial design specified various levels of traffic intensity and overlay thickness for b...

Optimization of Asphalt Mixture Design for the Louisiana ALF Test Sections

DOT National Transportation Integrated Search

2018-05-01

This research presents an extensive study on the design and characterization of asphalt mixtures used in road pavements. Both mixture volumetrics and physical properties obtained from several laboratory tests were considered in optimizing the mixture...

Animals in the Classroom: A Guide for Teachers. Elementary Science Study.

ERIC Educational Resources Information Center

Gillmor, Mary S.; And Others

This guide is designed to encourage people to keep animals of all kinds in the classroom and to use them in teaching language arts, mathematics, and social studies, as well as science and nature study. The booklet is divided into four sections. The first section contains an account of a year with desert animals in an ungraded classroom of six- to…

Design Study of a Modular Gas-Cooled, Closed-Brayton Cycle Reactor for Marine Use

DTIC Science & Technology

1989-06-01

materials in the core and surroundings. To investigate this design point in the marine variant I developed the program HEAT.BAS to perform a one-dimensional...helium as the working fluid. The core is a graphite moderated, epithermal spectrum reactor, using TRISO fuel particles in extruded graphite fuel elements...The fuel is highly enriched U2315 . The containment is shaped in an inverted ’T’ with two sections. The upper section contains the reactor core

Section Preequating under the Equivalent Groups Design without IRT

ERIC Educational Resources Information Center

Guo, Hongwen; Puhan, Gautam

2014-01-01

In this article, we introduce a section preequating (SPE) method (linear and nonlinear) under the randomly equivalent groups design. In this equating design, sections of Test X (a future new form) and another existing Test Y (an old form already on scale) are administered. The sections of Test X are equated to Test Y, after adjusting for the…

Preliminary Options Assessment of Versatile Irradiation Test Reactor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sen, Ramazan Sonat

The objective of this report is to summarize the work undertaken at INL from April 2016 to January 2017 and aimed at analyzing some options for designing and building a versatile test reactor; the scope of work was agreed upon with DOE-NE. Section 2 presents some results related to KNK II and PRISM Mod A. Section 3 presents some alternatives to the VCTR presented in [ ] as well as a neutronic parametric study to assess the minimum power requirement needed for a 235U metal fueled fast test reactor capable to generate a fast (>100 keV) flux of 4.0 xmore » 1015 n /cm2-s at the test location. Section 4 presents some results regarding a fundamental characteristic of test reactors, namely displacement per atom (dpa) in test samples. Section 5 presents the INL assessment of the ANL fast test reactor design FASTER. Section 6 presents a summary.« less

Local Deplanation Of Double Reinforced Beam Cross Section Under Bending

NASA Astrophysics Data System (ADS)

Baltov, Anguel; Yanakieva, Ana

2015-12-01

Bending of beams, double reinforced by means of thin composite layers, is considered in the study. Approximate numerical solution is proposed, considering transitional boundary areas, where smooth quadratic transition of the elasticity modulus and deformations take place. Deplanation of the cross section is also accounted for in the areas. Their thickness is found equalizing the total stiffness of the cross section and the layer stiffness. Deplanation of the cross section of the transitional area is determined via the longitudinal deformation in the reinforcing layer, accounting for the equilibrium between the internal and the external moment, generated by the longitudinal stresses in the cross section. A numerical example is given as an illustration demonstrating model's plausibility. The model allows the design and the calculation of recycled concrete beams double reinforced by means of thin layers. The approach is in agreement with modern design of nearly zero energy buildings (NZEB).

Optimization of Root Section for Ultra-long Steam Turbine Rotor Blade

NASA Astrophysics Data System (ADS)

Hála, Jindřich; Luxa, Martin; Šimurda, David; Bobčík, Marek; Novák, Ondřej; Rudas, Bartoloměj; Synáč, Jaroslav

2018-04-01

This study presents the comparison of aerodynamic performances of two successive designs of the root profiles for the ultra-long rotor blade equipped with a straight fir-tree dovetail. Since aerodynamic and strength requirements laid upon the root section design are contradictory, it is necessary to aerodynamically optimize the design within the limits given by the foremost strength requirements. The most limiting criterion of the static strength is the size of the blade cross-section, which is determined by the number of blades in a rotor and also by the shape and size of a blade dovetail. The aerodynamic design requires mainly the zero incidence angle at the inlet of a profile and in the ideal case ensures that the load does not exceed a limit load condition. Moreover, the typical root profile cascades are transonic with supersonic exit Mach number, therefore, the shape of a suction side and a trailing edge has to respect transonic expansion of a working gas. In this paper, the two variants of root section profile cascades are compared and the aerodynamic qualities of both variants are verified using CFD simulation and two mutually independent experimental methods of measurements (optical and pneumatic).

Using Faculty Characteristics to Predict Attitudes toward Developmental Education

ERIC Educational Resources Information Center

Sides, Meredith Louise Carr

2017-01-01

The study adapted Astin's I-E-O model and utilized multiple regression analyses to predict faculty attitudes toward developmental education. The study utilized a cross-sectional survey design to survey faculty members at 27 different higher education institutions in the state of Alabama. The survey instrument was a self-designed questionnaire that…

Motivational Factors and Teachers Commitment in Public Secondary Schools in Mbale Municipality

ERIC Educational Resources Information Center

Olurotimi, Ogunlade Joseph; Asad, Kamonges Wahab; Abdulrauf, Abdulkadir

2015-01-01

The study investigated the influence of motivational factors on teachers' commitment in public Secondary School in Mbale Municipality. The study employed Cross-sectional survey design. The sampling technique used to select was simple random sampling technique. The instrument used to collect data was a self designed questionnaire. The data…

Promising Practices in CTS.

ERIC Educational Resources Information Center

Alberta Dept. of Education, Edmonton. Curriculum Standards Branch.

This document contains 85 articles taken from previously published issues of the "CTS Communication Network Update," a publication about the career and technology studies (CTS) program of career education designed for Alberta, Canada, high school juniors and seniors. Following an introductory section and a section on general CTS, the…

Performance investigations on modified vertical axis water turbine: Combination of lift and drag

NASA Astrophysics Data System (ADS)

Baumatary, Mithinga; Biswas, Angimitra; Misra, Rahul Dev

2018-04-01

Extracting energy from the water has been followed since decades due to environmental friendly. Now a days everyone is running after clean energy, therefore extracting energy from the water turbine is a good approach. The main idea of this study is to investigate the performance of a new design turbine which is a combination of the concepts of lift and drag turbine. The main purpose of the study is to accumulate maximum energy by considering advantages of two different types of turbine. The maximum coefficient of power is 0.141 at free stream velocity of 0.5 m/s. The modified new design turbine consist of straight section and the curve section. The length of the straight section influences the performance of the turbine. Investigation on the optimization of straight section has been carried out in this paper. As this type of turbine have opted the advantages of both lift and drag it has turned out to be fruitful.

40 CFR 1048.615 - What are the provisions for exempting engines designed for lawn and garden applications?

Code of Federal Regulations, 2014 CFR

2014-07-01

... engines designed for lawn and garden applications? 1048.615 Section 1048.615 Protection of Environment... designed for lawn and garden applications? This section is intended for engines designed for lawn and garden applications, but it applies to any engines meeting the criteria in paragraph (a) of this section...

40 CFR 1048.615 - What are the provisions for exempting engines designed for lawn and garden applications?

Code of Federal Regulations, 2013 CFR

2013-07-01

... engines designed for lawn and garden applications? 1048.615 Section 1048.615 Protection of Environment... designed for lawn and garden applications? This section is intended for engines designed for lawn and garden applications, but it applies to any engines meeting the criteria in paragraph (a) of this section...

40 CFR 1048.615 - What are the provisions for exempting engines designed for lawn and garden applications?

Code of Federal Regulations, 2011 CFR

2011-07-01

... engines designed for lawn and garden applications? 1048.615 Section 1048.615 Protection of Environment... designed for lawn and garden applications? This section is intended for engines designed for lawn and garden applications, but it applies to any engines meeting the criteria in paragraph (a) of this section...

40 CFR 1048.615 - What are the provisions for exempting engines designed for lawn and garden applications?

Code of Federal Regulations, 2012 CFR

2012-07-01

... engines designed for lawn and garden applications? 1048.615 Section 1048.615 Protection of Environment... designed for lawn and garden applications? This section is intended for engines designed for lawn and garden applications, but it applies to any engines meeting the criteria in paragraph (a) of this section...

29 CFR 1640.9 - Processing of complaints or charges of employment discrimination filed with a designated agency...

Code of Federal Regulations, 2012 CFR

2012-07-01

... discrimination filed with a designated agency and either a section 504 agency, the EEOC, or both. 1640.9 Section 1640.9 Labor Regulations Relating to Labor (Continued) EQUAL EMPLOYMENT OPPORTUNITY COMMISSION... and either a section 504 agency, the EEOC, or both. (a) Designated agency processing. A designated...

29 CFR 1640.9 - Processing of complaints or charges of employment discrimination filed with a designated agency...

Code of Federal Regulations, 2014 CFR

2014-07-01

... discrimination filed with a designated agency and either a section 504 agency, the EEOC, or both. 1640.9 Section 1640.9 Labor Regulations Relating to Labor (Continued) EQUAL EMPLOYMENT OPPORTUNITY COMMISSION... and either a section 504 agency, the EEOC, or both. (a) Designated agency processing. A designated...

29 CFR 1640.9 - Processing of complaints or charges of employment discrimination filed with a designated agency...

Code of Federal Regulations, 2011 CFR

2011-07-01

... discrimination filed with a designated agency and either a section 504 agency, the EEOC, or both. 1640.9 Section 1640.9 Labor Regulations Relating to Labor (Continued) EQUAL EMPLOYMENT OPPORTUNITY COMMISSION... and either a section 504 agency, the EEOC, or both. (a) Designated agency processing. A designated...

29 CFR 1640.9 - Processing of complaints or charges of employment discrimination filed with a designated agency...

Code of Federal Regulations, 2010 CFR

2010-07-01

... discrimination filed with a designated agency and either a section 504 agency, the EEOC, or both. 1640.9 Section 1640.9 Labor Regulations Relating to Labor (Continued) EQUAL EMPLOYMENT OPPORTUNITY COMMISSION... and either a section 504 agency, the EEOC, or both. (a) Designated agency processing. A designated...

Life Satisfaction Questionnaire (Lisat-9): Reliability and Validity for Patients with Acquired Brain Injury

ERIC Educational Resources Information Center

Boonstra, Anne M.; Reneman, Michiel F.; Stewart, Roy E.; Balk, Gerlof A.

2012-01-01

The aim of this study was to determine the reliability and discriminant validity of the Dutch version of the life satisfaction questionnaire (Lisat-9 DV) to assess patients with an acquired brain injury. The reliability study used a test-retest design, and the validity study used a cross-sectional design. The setting was the general rehabilitation…

Asphaltic concrete overlays of rigid and flexible pavements : interim report No. 1.

DOT National Transportation Integrated Search

1977-09-01

This study evaluated the effect of a given thickness of asphaltic concrete overlay in rehabilitating 53 test sections conforming to the experiment design. This factorial design specified various levels of traffic intensity and overlay thickness for b...

Optimal Design of Sheet Pile Wall Embedded in Clay

NASA Astrophysics Data System (ADS)

Das, Manas Ranjan; Das, Sarat Kumar

2015-09-01

Sheet pile wall is a type of flexible earth retaining structure used in waterfront offshore structures, river protection work and temporary supports in foundations and excavations. Economy is an essential part of a good engineering design and needs to be considered explicitly in obtaining an optimum section. By considering appropriate embedment depth and sheet pile section it may be possible to achieve better economy. This paper describes optimum design of both cantilever and anchored sheet pile wall penetrating clay using a simple optimization tool Microsoft Excel ® Solver. The detail methodology and its application with examples are presented for cantilever and anchored sheet piles. The effects of soil properties, depth of penetration and variation of ground water table on the optimum design are also discussed. Such a study will help professional while designing the sheet pile wall penetrating clay.

Design of cryogenic tanks for space vehicles shell structures analytical modeling

NASA Technical Reports Server (NTRS)

Copper, Charles; Mccarthy, K.; Pilkey, W. D.; Haviland, J. K.

1991-01-01

The initial objective was to study the use of superplastically formed corrugated hat section stringers and frames in place of integrally machined stringers over separate frames for the tanks of large launch vehicles subjected to high buckling loads. The ALS was used as an example. The objective of the follow-on project was to study methods of designing shell structures subjected to severe combinations of structural loads and thermal gradients, with emphasis on new combinations of structural arrangements and materials. Typical applications would be to fuselage sections of high speed civil transports and to cryogenic tanks on the National Aerospace Plane.

The Effect of Using Dynamic Mathematics Software: Cross Section and Visualization

ERIC Educational Resources Information Center

Kösa, Temel

2016-01-01

The main purpose of this study is to determine the effects of using dynamic mathematics software on pre-service mathematics teachers' ability to infer the shape of a cross section of a three-dimensional solid, as well as on their spatial visualization skills. The study employed a quasi-experimental design with a control group; the Purdue Spatial…

Observational Study of Preschool Education and Care for Disadvantaged Children: Recommendations for Measuring Cognitive and Social-Emotional Outcomes among Chapter 1 Children.

ERIC Educational Resources Information Center

Seppanen, Patricia S.; Love, John M.

This paper presents recommendations about measures for assessing cognitive and social-emotional outcomes of children in Chapter 1 preschool and kindergarten programs. Section I explains the purpose and design of the study, giving special attention to the Chapter 1 substudy. Section II covers critical issues related to cognitive and…

Comparison of gimbal approaches to decrease drag force and radar cross sectional area in missile application

NASA Astrophysics Data System (ADS)

Sakarya, Doǧan Uǧur

2017-05-01

Drag force effect is an important aspect of range performance in missile applications especially for long flight time. However, old fashioned gimbal approaches force to increase missile diameter. This increase has negative aspect of rising in both drag force and radar cross sectional area. A new gimbal approach was proposed recently. It uses a beam steering optical arrangement. Therefore, it needs less volume envelope for same field of regard and same optomechanical assembly than the old fashioned gimbal approaches. In addition to longer range performance achieved with same fuel in the new gimbal approach, this method provides smaller cross sectional area which can be more invisible in enemies' radar. In this paper, the two gimbal approaches - the old fashioned one and the new one- are compared in order to decrease drag force and radar cross sectional area in missile application. In this study; missile parameters are assumed to generate gimbal and optical design parameters. Optical design is performed according to these missile criteria. Two gimbal configurations are designed with respect to modeled missile parameters. Also analyzes are performed to show decreased drag force and radar cross sectional area in the new approach for comparison.

Impact of Study Design on Reported Incidences of Acute Mountain Sickness: A Systematic Review.

PubMed

Waeber, Baptiste; Kayser, Bengt; Dumont, Lionel; Lysakowski, Christopher; Tramèr, Martin R; Elia, Nadia

2015-09-01

Published incidences of acute mountain sickness (AMS) vary widely. Reasons for this variation, and predictive factors of AMS, are not well understood. We aimed to identify predictive factors that are associated with the occurrence of AMS, and to test the hypothesis that study design is an independent predictive factor of AMS incidence. We did a systematic search (Medline, bibliographies) for relevant articles in English or French, up to April 28, 2013. Studies of any design reporting on AMS incidence in humans without prophylaxis were selected. Data on incidence and potential predictive factors were extracted by two reviewers and crosschecked by four reviewers. Associations between predictive factors and AMS incidence were sought through bivariate and multivariate analyses for different study designs separately. Association between AMS incidence and study design was assessed using multiple linear regression. We extracted data from 53,603 subjects from 34 randomized controlled trials, 44 cohort studies, and 33 cross-sectional studies. In randomized trials, the median of AMS incidences without prophylaxis was 60% (range, 16%-100%); mode of ascent and population were significantly associated with AMS incidence. In cohort studies, the median of AMS incidences was 51% (0%-100%); geographical location was significantly associated with AMS incidence. In cross-sectional studies, the median of AMS incidences was 32% (0%-68%); mode of ascent and maximum altitude were significantly associated with AMS incidence. In a multivariate analysis, study design (p=0.012), mode of ascent (p=0.003), maximum altitude (p<0.001), population (p=0.002), and geographical location (p<0.001) were significantly associated with AMS incidence. Age, sex, speed of ascent, duration of exposure, or history of AMS were inconsistently reported and therefore not further analyzed. Reported incidences and identifiable predictive factors of AMS depend on study design.

Jacks--A Study of Simple Machines.

ERIC Educational Resources Information Center

Parsons, Ralph

This vocational physics individualized student instructional module on jacks (simple machines used to lift heavy objects) contains student prerequisites and objectives, an introduction, and sections on the ratchet bumper jack, the hydraulic jack, the screw jack, and load limitations. Designed with a laboratory orientation, each section consists of…

A Systematic Review of Psychological Studies Applied to Futsal

PubMed Central

Dias, Cláudia Salomé; Fonseca, António Manuel

2016-01-01

Abstract This study presents a systematic review of psychological studies applied to futsal. A total of 23 studies were analyzed within five sections: a year overview and the name of journals, research designs, data collection, sample characteristics, and a focus category. This study found that the first psychological articles that were applied to futsal were published in 2008, and the number of publications gradually increased since then. The majority of examined studies were cross-sectional designs and conducted at the elite level in European and Asian countries. Most studies did not use mixed methods and did not specify the age of the subjects. Psychological research applied to futsal focused on athletes, non-athletes and several psychological factors. Critical and innovative reflections were made to highlight research gaps and present suggestions for further research. PMID:28149362

The Effects of the Critical Ice Accretion on Airfoil and Wing Performance

NASA Technical Reports Server (NTRS)

Selig, Michael S.; Bragg, Michael B.; Saeed, Farooq

1998-01-01

In support of the NASA Lewis Modern Airfoils Ice Accretion Test Program, the University of Illinois at Urbana-Champaign provided expertise in airfoil design and aerodynamic analysis to determine the aerodynamic effect of ice accretion on modern airfoil sections. The effort has concentrated on establishing a design/testing methodology for "hybrid airfoils" or "sub-scale airfoils," that is, airfoils having a full-scale leading edge together with a specially designed and foreshortened aft section. The basic approach of using a full-scale leading edge with a foreshortened aft section was considered to a limited extent over 40 years ago. However, it was believed that the range of application of the method had not been fully exploited. Thus a systematic study was being undertaken to investigate and explore the range of application of the method so as to determine its overall potential.

Information content of household-stratified epidemics.

PubMed

Kinyanjui, T M; Pellis, L; House, T

2016-09-01

Household structure is a key driver of many infectious diseases, as well as a natural target for interventions such as vaccination programs. Many theoretical and conceptual advances on household-stratified epidemic models are relatively recent, but have successfully managed to increase the applicability of such models to practical problems. To be of maximum realism and hence benefit, they require parameterisation from epidemiological data, and while household-stratified final size data has been the traditional source, increasingly time-series infection data from households are becoming available. This paper is concerned with the design of studies aimed at collecting time-series epidemic data in order to maximize the amount of information available to calibrate household models. A design decision involves a trade-off between the number of households to enrol and the sampling frequency. Two commonly used epidemiological study designs are considered: cross-sectional, where different households are sampled at every time point, and cohort, where the same households are followed over the course of the study period. The search for an optimal design uses Bayesian computationally intensive methods to explore the joint parameter-design space combined with the Shannon entropy of the posteriors to estimate the amount of information in each design. For the cross-sectional design, the amount of information increases with the sampling intensity, i.e., the designs with the highest number of time points have the most information. On the other hand, the cohort design often exhibits a trade-off between the number of households sampled and the intensity of follow-up. Our results broadly support the choices made in existing epidemiological data collection studies. Prospective problem-specific use of our computational methods can bring significant benefits in guiding future study designs. Copyright © 2016 The Authors. Published by Elsevier B.V. All rights reserved.

Penetration of immunoreagents in Vibratome-sectioned brain: a light and electron microscopic study.

PubMed

Piekut, D T; Casey, S M

1983-05-01

Immunocytochemical studies on the localization of peptides at the ultrastructural level have most frequently involved the application of the peroxidase--antiperoxidase (PAP) method of immunocytochemistry and the use of the preembedding or postembedding staining procedures. The present study was designed to determine the depth of penetration of Vibratome tissue sections by immunoreagents used in the preembedding method in which immunostaining of unembedded fixed tissue sections is accomplished prior to tissue dehydration and embedment. Our data indicate that penetration of immunoreagents is restricted to the superficial 8-9 micrometers of a 80-micrometers thick Vibratome tissue section of hypothalamus of brain using antisera generated against arginine vasopressin. The final immunoreaction product visualized in a Vibratome tissue section may reflect only a fraction of the amount of hormone contained within the thickness of the tissue section.

Impacts of Performance Pay under the Teacher Incentive Fund: Study Design Report

ERIC Educational Resources Information Center

Glazerman, Steven; Chiang, Hanley; Wellington, Alison; Constantine, Jill; Player, Dan

2011-01-01

The body of research on the design, implementation, and effects of performance-based compensation systems has influenced the design and evaluation of the 2010 Teacher Incentive Fund (TIF) grants. In the sections presented here, the authors describe the key components of 2010 TIF grants and the conceptual framework for the evaluation. The remainder…

Design of field experiments: Influence of treatment response relative to standard deviation and blocking factor characteristics on efficient blocking strategy

USDA-ARS?s Scientific Manuscript database

Selection of experimental design can markedly influence efficiency of field research. This study used Monte Carlo simulations to compare the ability of different field experimental designs to distinguish defined treatment differences, and the paper concludes with a section on practical use of the in...

Where We Have Been and Where We Are Going: A Content Analysis of Articles Published in the Journal of Women's Health Physical Therapy From 2005 to 2015

PubMed Central

Coronado, Rogelio A.; Hill, Alexandra D.; Alappattu, Meryl J.

2018-01-01

Objective The objective of this study was to examine the type and content of Journal of Women’s Health Physical Therapy (JWHPT) publications over the last decade. Study Design Content and bibliometric analysis of published literature Background Component sections, such as the Section on Women’s Health (SoWH) of the American Physical Therapy Association provide content expertise to areas of specialty physical therapist practice, thereby supporting the dissemination of evidence for physical therapists to use. Closely aligned with the mission of the SoWH, JWHPT provides evidence reflecting this practice area. The purpose of our analysis was to examine publications within JWHPT to determine how closely JWHPT is meeting the mission and focus of section members. Methods and Measures We used established bibliographic methodology to code and review manuscripts published online between 2005 and 2015 in JWHPT using established domains (article type, participant type, research design, study purpose, and area of focus). Total publications and proportion of publications based on domain were described. Impact by citation and author was examined using bibliometric software. Results Eighteen percent of the items published in JWHPT were original research papers submitted for the first time. Of those papers, the primary study design was cross-sectional experimental research, most commonly studying interventions. The primary practice area reported was management of incontinence. Conclusions We suggest that a continued need to increase efforts for the submission and publication of a greater proportion of randomized controlled trials and metric articles. PMID:29375281

Overview of clinical research design.

PubMed

Hartung, Daniel M; Touchette, Daniel

2009-02-15

Basic concepts and terminology of clinical research design are presented for new clinical investigators. Clinical research, research involving human subjects, can be described as either observational or experimental. The findings of all clinical research can be threatened by issues of bias and confounding. Biases are systematic errors in how study subjects are selected or measured, which result in false inferences. Confounding is a distortion in findings that is attributable to mixing variable effects. Uncontrolled observation research is generally more prone to bias and confounding than experimental research. Observational research includes designs such as the cohort study, case-control study, and cross-sectional study, while experimental research typically involves a randomized controlled trial (RCT). The cohort study, which includes the RCT, defines subject allocation on the basis of exposure interest (e.g., drug, disease-management program) and follows the patients to assess the outcomes. The case-control study uses the primary outcome of interest (e.g., adverse event) to define subject allocation, and different exposures are assessed in a retrospective manner. Cross-sectional research evaluates both exposure and outcome concurrently. Each of these design methods possesses different strengths and weaknesses in answering research questions, as well as underlying many study subtypes. While experimental research is the strongest method for establishing causality, it can be difficult to accomplish under many scenarios. Observational clinical research offers many design alternatives that may be appropriate if planned and executed carefully.

14 CFR 25.1181 - Designated fire zones; regions included.

Code of Federal Regulations, 2012 CFR

2012-01-01

... engines; and (7) Combustor, turbine, and tailpipe sections of turbine engine installations that contain... Protection § 25.1181 Designated fire zones; regions included. (a) Designated fire zones are— (1) The engine power section; (2) The engine accessory section; (3) Except for reciprocating engines, any complete...

14 CFR 25.1181 - Designated fire zones; regions included.

Code of Federal Regulations, 2010 CFR

2010-01-01

... engines; and (7) Combustor, turbine, and tailpipe sections of turbine engine installations that contain... Protection § 25.1181 Designated fire zones; regions included. (a) Designated fire zones are— (1) The engine power section; (2) The engine accessory section; (3) Except for reciprocating engines, any complete...

14 CFR 25.1181 - Designated fire zones; regions included.

Code of Federal Regulations, 2013 CFR

2013-01-01

... engines; and (7) Combustor, turbine, and tailpipe sections of turbine engine installations that contain... Protection § 25.1181 Designated fire zones; regions included. (a) Designated fire zones are— (1) The engine power section; (2) The engine accessory section; (3) Except for reciprocating engines, any complete...

14 CFR 25.1181 - Designated fire zones; regions included.

Code of Federal Regulations, 2011 CFR

2011-01-01

... engines; and (7) Combustor, turbine, and tailpipe sections of turbine engine installations that contain... Protection § 25.1181 Designated fire zones; regions included. (a) Designated fire zones are— (1) The engine power section; (2) The engine accessory section; (3) Except for reciprocating engines, any complete...

14 CFR 25.1181 - Designated fire zones; regions included.

Code of Federal Regulations, 2014 CFR

2014-01-01

... engines; and (7) Combustor, turbine, and tailpipe sections of turbine engine installations that contain... Protection § 25.1181 Designated fire zones; regions included. (a) Designated fire zones are— (1) The engine power section; (2) The engine accessory section; (3) Except for reciprocating engines, any complete...

Stroke-Related Knowledge, Lifestyle Behaviours and Health Beliefs in Singaporean Chinese: Implications for Health Education

ERIC Educational Resources Information Center

Wong, Wai Pong; Yeung, Meredith; Loh, Susan; Lee, Mina; Ghazali, F.; Chan, C. J.; Feng, S.; Liew, Y. V.; Seah, P. F.; Wee, J.; Wang, J.; Huang, X.; Dean, Elizabeth

2013-01-01

Objective: The objective of the present study was to describe stroke-related knowledge (risk factors, warning signs and emergency response), lifestyle behaviours and health beliefs among Singaporean Chinese, and to identify any factors associated with such knowledge, behaviours and beliefs. Design: This was a cross-sectional study design employing…

Large-scale breeder reactor prototype mechanical pump conceptual design study, hot leg

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1976-09-01

Due to the extensive nature of this study, the report is presented as a series of small reports. The complete design analysis is placed in a separate section. The drawings and tabulations are in the back portion of the report. Other topics are enumerated and located as shown in the table of contents.

The Role of Flow Experience and CAD Tools in Facilitating Creative Behaviours for Architecture Design Students

ERIC Educational Resources Information Center

Dawoud, Husameddin M.; Al-Samarraie, Hosam; Zaqout, Fahed

2015-01-01

This study examined the role of flow experience in intellectual activity with an emphasis on the relationship between flow experience and creative behaviour in design using CAD. The study used confluence and psychometric approaches because of their unique abilities to depict a clear image of creative behaviour. A cross-sectional study…

Designing mark-recapture studies to reduce effects of distance weighting on movement distance distributions of stream fishes

USGS Publications Warehouse

Albanese, B.; Angermeier, P.L.; Gowan, C.

2003-01-01

Mark-recapture studies generate biased, or distance-weighted, movement data because short distances are sampled more frequently than long distances. Using models and field data, we determined how study design affects distance weighting and the movement distributions of stream fishes. We first modeled distance weighting as a function of recapture section length in an unbranching stream. The addition of an unsampled tributary to one of these models substantially increased distance weighting by decreasing the percentage of upstream distances that were sampled. Similarly, the presence of multiple tributaries in the field study resulted in severe bias. However, increasing recapture section length strongly affected distance weighting in both the model and the field study, producing a zone where the number of fish moving could be estimated with little bias. Subsampled data from the field study indicated that longer median (three of three species) and maximum distances (two of three species) can be detected by increasing the length of the recapture section. The effect was extreme for bluehead chub Nocomis leptocephalus, a highly mobile species, which exhibited a longer median distance (133 m versus 60 m), a longer maximum distance (1,144 m versus 708 m), and a distance distribution that differed in shape when the full (4,123-m recapture section) and subsampled (1,978-m recapture section) data sets were compared. Correction factors that adjust the observed number of movements to undersampled distances upwards and those to oversampled distances downwards could not mitigate the distance weighting imposed by the shorter recapture section. Future studies should identify the spatial scale over which movements can be accurately measured before data are collected. Increasing recapture section length a priori is far superior to using post hoc correction factors to reduce the influence of distance weighting on observed distributions. Implementing these strategies will be especially important in stream networks where fish can follow multiple pathways out of the recapture section.

7 CFR 621.44 - Special studies.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 6 2011-01-01 2011-01-01 false Special studies. 621.44 Section 621.44 Agriculture... studies. As designated, NRCS represents USDA on special study groups such as for the Colorado River Basin Salinity Control Program Studies. ...

7 CFR 621.44 - Special studies.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 6 2010-01-01 2010-01-01 false Special studies. 621.44 Section 621.44 Agriculture... studies. As designated, NRCS represents USDA on special study groups such as for the Colorado River Basin Salinity Control Program Studies. ...

Experimental Investigation of a Point Design Optimized Arrow Wing HSCT Configuration

NASA Technical Reports Server (NTRS)

Narducci, Robert P.; Sundaram, P.; Agrawal, Shreekant; Cheung, S.; Arslan, A. E.; Martin, G. L.

1999-01-01

The M2.4-7A Arrow Wing HSCT configuration was optimized for straight and level cruise at a Mach number of 2.4 and a lift coefficient of 0.10. A quasi-Newton optimization scheme maximized the lift-to-drag ratio (by minimizing drag-to-lift) using Euler solutions from FL067 to estimate the lift and drag forces. A 1.675% wind-tunnel model of the Opt5 HSCT configuration was built to validate the design methodology. Experimental data gathered at the NASA Langley Unitary Plan Wind Tunnel (UPWT) section #2 facility verified CFL3D Euler and Navier-Stokes predictions of the Opt5 performance at the design point. In turn, CFL3D confirmed the improvement in the lift-to-drag ratio obtained during the optimization, thus validating the design procedure. A data base at off-design conditions was obtained during three wind-tunnel tests. The entry into NASA Langley UPWT section #2 obtained data at a free stream Mach number, M(sub infinity), of 2.55 as well as the design Mach number, M(sub infinity)=2.4. Data from a Mach number range of 1.8 to 2.4 was taken at UPWT section #1. Transonic and low supersonic Mach numbers, M(sub infinity)=0.6 to 1.2, was gathered at the NASA Langley 16 ft. Transonic Wind Tunnel (TWT). In addition to good agreement between CFD and experimental data, highlights from the wind-tunnel tests include a trip dot study suggesting a linear relationship between trip dot drag and Mach number, an aeroelastic study that measured the outboard wing deflection and twist, and a flap scheduling study that identifies the possibility of only one leading-edge and trailing-edge flap setting for transonic cruise and another for low supersonic acceleration.

Analysis of subsonic wind tunnel with variation shape rectangular and octagonal on test section

NASA Astrophysics Data System (ADS)

Rhakasywi, D.; Ismail; Suwandi, A.; Fadhli, A.

2018-02-01

The need for good design in the aerodynamics field required a wind tunnel design. The wind tunnel design required in this case is capable of generating laminar flow. In this research searched for wind tunnel models with rectangular and octagonal variations with objectives to generate laminar flow in the test section. The research method used numerical approach of CFD (Computational Fluid Dynamics) and manual analysis to analyze internal flow in test section. By CFD simulation results and manual analysis to generate laminar flow in the test section is a design that has an octagonal shape without filled for optimal design.

Staff Perspectives on the Use of a Computer-Based Concept for Lifestyle Intervention Implemented in Primary Health Care

ERIC Educational Resources Information Center

Carlfjord, Siw; Johansson, Kjell; Bendtsen, Preben; Nilsen, Per; Andersson, Agneta

2010-01-01

Objective: The aim of this study was to evaluate staff experiences of the use of a computer-based concept for lifestyle testing and tailored advice implemented in routine primary health care (PHC). Design: The design of the study was a cross-sectional, retrospective survey. Setting: The study population consisted of staff at nine PHC units in the…

Curriculum History, Schooling and the History of the Present

ERIC Educational Resources Information Center

Popkewitz, Thomas S.

2011-01-01

The essay focuses on curriculum history as the study of systems of reason. The first section considers curriculum as "converting ordinances", inscribing Puritan notions of education as evangelizing and calculating designs in American Progressive education. The second section examines the Social Question, a cross-Atlantic Protestant reformist…

Energy Conservation in Construction Trades. Special Packages: Instructional Resources for Vocational Education.

ERIC Educational Resources Information Center

Ohio State Univ., Columbus. National Center for Research in Vocational Education.

Designed for secondary and postsecondary vocational teachers and administrators, this resource package on energy conservation in construction trades contains three sections of information. Section I provides an instructional module (developed by the Wisconsin Vocational Studies Center) on solar energy; the module is organized into seven units:…

Development of drive mechanism for an oscillating airfoil

NASA Technical Reports Server (NTRS)

Sticht, Clifford D.

1988-01-01

The design and development of an in-draft wind tunnel test section which will be used to study the dynamic stall of airfoils oscillating in pitch is described. The hardware developed comprises a spanned airfoil between schleiren windows, a four bar linkage, flywheels, a drive system and a test section structure.

Current Illinois Legal Issues. Second Edition.

ERIC Educational Resources Information Center

Kopecky, Frank J., Ed.; Wilkin, Rebecca S., Ed.

Designed as supplementary reading in American government or social studies courses, this compilation of articles is intended to help students gain a better understanding of the judiciary's role in the Illinois legal system. The first of three sections contains articles about judges and the court system. The second section examines the criminal…

Remote Sensing and the Earth.

ERIC Educational Resources Information Center

Brosius, Craig A.; And Others

This document is designed to help senior high school students study remote sensing technology and techniques in relation to the environmental sciences. It discusses the acquisition, analysis, and use of ecological remote data. Material is divided into three sections and an appendix. Section One is an overview of the basics of remote sensing.…

The Recovery of Energy from Waste.

ERIC Educational Resources Information Center

Baxter, Zeland L.; And Others

This study unit advocates the use of biomass conversion techniques with municipal solid wastes as a viable action for energy development. The unit includes: (1) an introductory section (providing a unit overview and supportive statements for biomass conversion; (2) a historical review of energy use from wastes; (3) a section on design and…

Cognitive Development in Children with Brain Damage.

ERIC Educational Resources Information Center

Bortner, Morton

Presented is a report on a cross-sectional and longitudinal study concerned with the course of intellectual development in 210 children (6-12 years old) educationally designated as brain damaged (learning disabled and/or behavior problems) and assigned to special school placement. The report is divided into four sections which focus on…

Adaptive Automation Design and Implementation

DTIC Science & Technology

2015-09-17

Study : Space Navigator This section demonstrates the player modeling paradigm, focusing specifically on the response generation section of the player ...human-machine system, a real-time player modeling framework for imitating a specific person’s task performance, and the Adaptive Automation System...Model . . . . . . . . . . . . . . . . . . . . . . . 13 Clustering-Based Real-Time Player Modeling . . . . . . . . . . . . . . . . . . . . . . 15 An

Alcohol, Tobacco, and Other Drugs Resource Guide: Tobacco.

ERIC Educational Resources Information Center

Zuckerman, Karen, Ed.

This guide was designed to aid prevention specialists, educators, parents, and others in addressing tobacco problems among youth. Listed here are numerous publications--each one summarized--on tobacco use. The guide is divided into two sections: (1) Prevention Material for Tobacco; and (2) Studies, Articles, and Reports on Tobacco. Section one…

Themes and methods of research presented at European General Practice Research Network conferences.

PubMed

Kruschinski, Carsten; Lange, Maaike; Lionis, Christos; van Weel, Chris; Hummers-Pradier, Eva

2010-08-01

The World Organization of Family Doctors (Wonca) defined core characteristics of general practice and general practitioners' competencies. It is unclear to which extent research has addressed these issues so far. To determine themes and research methods of general practice research as reflected by presentations at the European General Practice Research Network (EGPRN) meetings. Descriptive and retrospective study. All abstracts presented at each of the 14 EGPRN conferences between June 2001 and October 2007 were analysed for content and study design/methodology. Categories for content were developed inductively; a predefined hierarchical scheme was used for study designs. A total of N=614 abstracts were classified. The main research topics were related to GP/health service issues (n=232), clinical (n=148) and patient-related themes (n=118). Original data (n=558) were mainly derived from cross-sectional designs (38.7%). Intervention studies (11.0%), longitudinal designs including case-control and cohort studies (13.3%) as well as instrumental research (2.2%) were less common. More than one-fourth of all original studies were qualitative studies (27.6%). Stratified analysis revealed that cross-sectional designs were less frequent in the second half of conferences. Analysis by country showed that, in contrast to different quantitative designs, the proportion of qualitative studies was comparable. To test effectiveness of diagnostic and therapeutic interventions under primary care conditions, a higher proportion of experimental studies would be preferable. This could increase the acceptance of general practitioners' specific approaches and provide clear guidance on approaches and procedures, especially in health care systems not predominantly based on primary care.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nexant, Inc., San Francisco, California

The first section (Task 1) of this report by Nexant includes a survey and screening of various acid gas removal processes in order to evaluate their capability to meet the specific design requirements for thermochemical ethanol synthesis in NREL's thermochemical ethanol design report (Phillips et al. 2007, NREL/TP-510-41168). MDEA and selexol were short-listed as the most promising acid-gas removal agents based on work described in Task 1. The second report section (Task 2) describes a detailed design of an MDEA (methyl diethanol amine) based acid gas removal system for removing CO2 and H2S from biomass-derived syngas. Only MDEA was chosenmore » for detailed study because of the available resources.« less

Lattice design of the integrable optics test accelerator and optical stochastic cooling experiment at Fermilab

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kafka, Gene

2015-05-01

The Integrable Optics Test Accelerator (IOTA) storage ring at Fermilab will serve as the backbone for a broad spectrum of Advanced Accelerator R&D (AARD) experiments, and as such, must be designed with signi cant exibility in mind, but without compromising cost e ciency. The nonlinear experiments at IOTA will include: achievement of a large nonlinear tune shift/spread without degradation of dynamic aperture; suppression of strong lattice resonances; study of stability of nonlinear systems to perturbations; and studies of di erent variants of nonlinear magnet design. The ring optics control has challenging requirements that reach or exceed the present state ofmore » the art. The development of a complete self-consistent design of the IOTA ring optics, meeting the demands of all planned AARD experiments, is presented. Of particular interest are the precise control for nonlinear integrable optics experiments and the transverse-to-longitudinal coupling and phase stability for the Optical Stochastic Cooling Experiment (OSC). Since the beam time-of- ight must be tightly controlled in the OSC section, studies of second order corrections in this section are presented.« less

Lattice design of the integrable optics test accelerator and optical stochastic cooling experiment at Fermilab

NASA Astrophysics Data System (ADS)

Kafka, Gene

The Integrable Optics Test Accelerator (IOTA) storage ring at Fermilab will serve as the backbone for a broad spectrum of Advanced Accelerator R&D (AARD) experiments, and as such, must be designed with significant flexibility in mind, but without compromising cost efficiency. The nonlinear experiments at IOTA will include: achievement of a large nonlinear tune shift/spread without degradation of dynamic aperture; suppression of strong lattice resonances; study of stability of nonlinear systems to perturbations; and studies of different variants of nonlinear magnet design. The ring optics control has challenging requirements that reach or exceed the present state of the art. The development of a complete self-consistent design of the IOTA ring optics, meeting the demands of all planned AARD experiments, is presented. Of particular interest are the precise control for nonlinear integrable optics experiments and the transverse-to-longitudinal coupling and phase stability for the Optical Stochastic Cooling Experiment (OSC). Since the beam time-of-flight must be tightly controlled in the OSC section, studies of second order corrections in this section are presented.

Final analysis and design of a thermal protection system for 8-foot HTST combustor

NASA Technical Reports Server (NTRS)

Moskowitz, S.

1973-01-01

The cylindrical shell combustor with T-bar supports in the 8-foot HTST at the NASA-Langley Research Center encountered vibratory fatigue cracking over a period of 50-250 tunnel tests within a limited range of the required operating envelope. A preliminary design study provided several suitable thermal protection system designs for the combustor, one of which was a two-pass regenerative type air-cooled omega-shaped segment liner. A final design layout of the omega segment liner was prepared and analyzed for steady-state and transient conditions. The design of a support system for the fuel spray bar assembly was also included. Detail drawings suitable for fabrication purposes were also prepared. Liner design problems defined during the preliminary study included (1) the ingress of gas into the attachment bulb section of the omega segment, (2) the large thermal gradient along the leg of the omega bulb attachment section and, (3) the local peak metal temperature at the radius between the liner ID and the leg of the bulb attachment. These were resolved during the final design task. Analyses of the final design of the omega segment liner indicated that all design goals were met and the design provided the capability of operating over the required test envelope with a life expectancy substantially above the goal of 1500 cycles.

A preliminary design study on an acoustic muffler for the laminar flow transition research apparatus

NASA Technical Reports Server (NTRS)

Abrahamson, A. L.

1984-01-01

An acoustic muffler design of a research tool for studying laminar flow and the mechanisms of transition, the Laminar Flow and Transition Research Apparatus (LFTRA) is investigated. Since the presence of acoustic pressure fluctuations is known to affect transition, low background noise levels in the test section of the LFTRA are mandatory. The difficulties and tradeoffs of various muffler design concepts are discussed and the most promising candidates are emphasized.

Study to investigate design, fabrication and test of low cost concepts for large hybrid composite helicopter fuselage, phase 2

NASA Technical Reports Server (NTRS)

Adams, K. M.; Lucas, J. J.

1977-01-01

The development of a frame/stringer/skin fabrication technique for composite airframe construction was studied as a low cost approach to the manufacturer of larger helicopter airframe components. A center cabin aluminum airframe section of the Sikorsky CH-53D, was selected for evaluation as a composite structure. The design, as developed, is composed of a woven KEVLAR R-49/epoxy skin and graphite/epoxy frames and stringers. The single cure concept is made possible by the utilization of pre-molded foam cores, over which the graphite/epoxy pre-impregnated frame and stringer reinforcements are positioned. Bolted composite channel sections were selected as the optimum joint construction. The applicability of the single cure concept to larger realistic curved airframe sections, and the durability of the composite structure in a realistic spectrum fatigue environment, was described.

Parental and Child Characteristics Related to Early-Onset Disordered Eating: A Systematic Review.

PubMed

Larsen, Pernille Stemann; Strandberg-Larsen, Katrine; Micali, Nadia; Andersen, Anne-Marie Nybo

2015-01-01

After participating in this activity, learners should be better able to: Evaluate the evidence regarding parental and child characteristics related to early-onset disordered eating. Eating disorders are rare in children, but disordered eating is common. Understanding the phenomenology of disordered eating in childhood can aid prevention of full-blown eating disorders. The purpose of this review is to systematically extract and synthesize the evidence on parental and child characteristics related to early-onset disordered eating. Systematic searches were conducted in PubMED/MEDLINE, EMBASE, and PsycInfo using the following search terms: eating disorder, disordered eating, problem eating, anorexia nervosa, bulimia nervosa, binge eating, child, preadolescent, and early onset. Studies published from 1990 to 2013 addressing parental and child characteristics of disordered eating in children aged 6 to 12 years were eligible for inclusion. The search was restricted to studies with cross-sectional, case-control, or longitudinal designs, studies in English, and with abstracts available. Forty-four studies fit these criteria. Most studies were based on community samples with a cross-sectional design. The included studies varied considerably in size, instruments used to assess early-onset disordered eating, and parental and child characteristics investigated. Important determinants included the following: higher body weight, previously reported disordered eating, body dissatisfaction, depression, parental disordered eating, and parental comments/concerns about child's weight and eating. The findings were inconsistent for sex, age, socioeconomic status, ethnicity, self-esteem/worth, and parental body weight. In conclusion, characteristics related to early-onset disordered eating have mainly been explored with a cross-sectional design. Full understanding of causal pathways will require good-quality longitudinal studies designed to address the influence of parental eating behaviors, mental and physical health, family interactions, and child growth patterns.

What Differentiates Adolescent Problematic Drinkers from Their Peers? Results from a Cross-Sectional Study in Northern Irish School Children

ERIC Educational Resources Information Center

McKay, Michael T.; Sumnall, Harry; Goudie, Andrew J.; Field, Matt; Cole, Jon C.

2011-01-01

Aim: To investigate whether or not a range of factors were associated with problematic drinking, as assessed using the Adolescent Alcohol Involvement Scale (AAIS) in a sample of 11-16-year olds in Northern Ireland. Methods: The study used a cross-sectional experimental design. Post-primary schools in the Eastern Health Board Area of Northern…

Investigation of two-stage air-cooled turbine suitable for flight at Mach number of 2.5 II : blade design

NASA Technical Reports Server (NTRS)

Miser, James W; Stewart, Warner L

1957-01-01

A blade design study is presented for a two-stage air-cooled turbine suitable for flight at a Mach number of 2.5 for which velocity diagrams have been previously obtained. The detailed procedure used in the design of the blades is given. In addition, the design blade shapes, surface velocity distributions, inner and outer wall contours, and other design data are presented. Of all the blade rows, the first-stage rotor has the highest solidity, with a value of 2.289 at the mean section. The second-stage stator also had a high mean-section solidity of 1.927, mainly because of its high inlet whirl. The second-stage rotor has the highest value of the suction-surface diffusion parameter, with a value of 0.151. All other blade rows have values for this parameter under 0.100.

Feasibility study on AFR-100 fuel conversion from uranium-based fuel to thorium-based fuel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Heidet, F.; Kim, T.; Grandy, C.

2012-07-30

Although thorium has long been considered as an alternative to uranium-based fuels, most of the reactors built to-date have been fueled with uranium-based fuel with the exception of a few reactors. The decision to use uranium-based fuels was initially made based on the technology maturity compared to thorium-based fuels. As a result of this experience, lot of knowledge and data have been accumulated for uranium-based fuels that made it the predominant nuclear fuel type for extant nuclear power. However, following the recent concerns about the extent and availability of uranium resources, thorium-based fuels have regained significant interest worldwide. Thorium ismore » more abundant than uranium and can be readily exploited in many countries and thus is now seen as a possible alternative. As thorium-based fuel technologies mature, fuel conversion from uranium to thorium is expected to become a major interest in both thermal and fast reactors. In this study the feasibility of fuel conversion in a fast reactor is assessed and several possible approaches are proposed. The analyses are performed using the Advanced Fast Reactor (AFR-100) design, a fast reactor core concept recently developed by ANL. The AFR-100 is a small 100 MW{sub e} reactor developed under the US-DOE program relying on innovative fast reactor technologies and advanced structural and cladding materials. It was designed to be inherently safe and offers sufficient margins with respect to the fuel melting temperature and the fuel-cladding eutectic temperature when using U-10Zr binary metal fuel. Thorium-based metal fuel was preferred to other thorium fuel forms because of its higher heavy metal density and it does not need to be alloyed with zirconium to reduce its radiation swelling. The various approaches explored cover the use of pure thorium fuel as well as the use of thorium mixed with transuranics (TRU). Sensitivity studies were performed for the different scenarios envisioned in order to determine the best core performance characteristics for each of them. With the exception of the fuel type and enrichment, the reference AFR-100 core design characteristics were kept unchanged, including the general core layout and dimensions, assembly dimensions, materials and power rating. In addition, the mass of {sup 235}U required was kept within a reasonable range from that of the reference AFR-100 design. The core performance characteristics, kinetics parameters and reactivity feedback coefficients were calculated using the ANL suite of fast reactor analysis code systems. Orifice design calculations and the steady-state thermal-hydraulic analyses were performed using the SE2-ANL code. The thermal margins were evaluated by comparing the peak temperatures to the design limits for parameters such as the fuel melting temperature and the fuel-cladding eutectic temperature. The inherent safety features of AFR-100 cores proposed were assessed using the integral reactivity parameters of the quasi-static reactivity balance analysis. The design objectives and requirements, the computation methods used as well as a description of the core concept are provided in Section 2. The three major approaches considered are introduced in Section 3 and the neutronics performances of those approaches are discussed in the same section. The orifice zoning strategies used and the steady-state thermal-hydraulic performance are provided in Section 4. The kinetics and reactivity coefficients, including the inherent safety characteristics, are provided in Section 5, and the Conclusions in Section 6. Other scenarios studied and sensitivity studies are provided in the Appendix section.« less

Twenty years' research on peer victimization and psychosocial maladjustment: a meta-analytic review of cross-sectional studies.

PubMed

Hawker, D S; Boulton, M J

2000-05-01

Cross-sectional quantitative designs are often used to investigate whether peer victimization is positively related to psychosocial maladjustment. This paper presents a meta-analytic review of cross-sectional studies, published between 1978 and 1997, of the association of peer victimization with psychosocial maladjustment. Mean effect sizes were calculated for the association between peer victimization and each form of maladjustment (depression, loneliness, generalized and social anxiety, and global and social self-worth) assessed. The results suggested that victimization is most strongly related to depression, and least strongly related to anxiety. There was no evidence that victimization is more strongly related to social than to psychological forms of maladjustment. Effect sizes were stronger when the same informants were used to assess both victimization and maladjustment than when different informants were used. There were some design limitations to the studies reviewed, but all together their results provide a strong background for more complex research into the course and treatment of victims' distress.

Two-phase flow pressure drop and heat transfer during condensation in microchannels with uniform and converging cross-sections

NASA Astrophysics Data System (ADS)

Kuo, Ching Yi; Pan, Chin

2010-09-01

This study experimentally investigates steam condensation in rectangular microchannels with uniform and converging cross-sections and a mean hydraulic diameter of 135 µm. The steam flow in the microchannels was cooled by water cross-flowing along its bottom surface, which is different from other methods reported in the literature. The flow patterns, two-phase flow pressure drop and condensation heat transfer coefficient are determined. The microchannels with the uniform cross-section design have a higher heat transfer coefficient than those with the converging cross-section under condensation in the mist/annular flow regimes, although the latter work best for draining two-phase fluids composed of uncondensed steam and liquid water, which is consistent with the result of our previous study. From the experimental results, dimensionless correlations of condensation heat transfer for the mist and annular flow regions and a two-phase frictional multiplier are developed for the microchannels with both types of cross-section designs. The experimental data agree well with the obtained correlations, with the maximum mean absolute errors of 6.4% for the two-phase frictional multiplier and 6.0% for the condensation heat transfer.

Oceanographic scanner system design study, volume 1

NASA Technical Reports Server (NTRS)

1971-01-01

The design is reported of a dual mode multispectral scanner, capable of satisfying both overland and oceanographic requirements. A complete system description and performance summary of the scanner are given. In addition, subsystem and component descriptions and performance analyses are treated in individual sections. The design of the scanner, with minimum modifications, interfaces to the ERTS spacecraft and the ground data handling system.

26 CFR 1.48-10 - Single purpose agricultural or horticultural structures.

Code of Federal Regulations, 2010 CFR

2010-04-01

... designed and constructed” test of paragraph (d) of this section since it would be economic to use the... specifically designed and constructed for permissible purposes (as defined in paragraph (b)(2) of this section). See paragraph (d) of this section for the rule regarding “specifically designed and constructed”. (ii...

26 CFR 1.48-10 - Single purpose agricultural or horticultural structures.

Code of Federal Regulations, 2011 CFR

2011-04-01

... designed and constructed” test of paragraph (d) of this section since it would be economic to use the... specifically designed and constructed for permissible purposes (as defined in paragraph (b)(2) of this section). See paragraph (d) of this section for the rule regarding “specifically designed and constructed”. (ii...

Multirate flutter suppression system design for the Benchmark Active Controls Technology Wing

NASA Technical Reports Server (NTRS)

Berg, Martin C.; Mason, Gregory S.

1994-01-01

To study the effectiveness of various control system design methodologies, the NASA Langley Research Center initiated the Benchmark Active Controls Project. In this project, the various methodologies will be applied to design a flutter suppression system for the Benchmark Active Controls Technology (BACT) Wing (also called the PAPA wing). Eventually, the designs will be implemented in hardware and tested on the BACT wing in a wind tunnel. This report describes a project at the University of Washington to design a multirate flutter suppression system for the BACT wing. The objective of the project was two fold. First, to develop a methodology for designing robust multirate compensators, and second, to demonstrate the methodology by applying it to the design of a multirate flutter suppression system for the BACT wing. The contributions of this project are (1) development of an algorithm for synthesizing robust low order multirate control laws (the algorithm is capable of synthesizing a single compensator which stabilizes both the nominal plant and multiple plant perturbations; (2) development of a multirate design methodology, and supporting software, for modeling, analyzing and synthesizing multirate compensators; and (3) design of a multirate flutter suppression system for NASA's BACT wing which satisfies the specified design criteria. This report describes each of these contributions in detail. Section 2.0 discusses our design methodology. Section 3.0 details the results of our multirate flutter suppression system design for the BACT wing. Finally, Section 4.0 presents our conclusions and suggestions for future research. The body of the report focuses primarily on the results. The associated theoretical background appears in the three technical papers that are included as Attachments 1-3. Attachment 4 is a user's manual for the software that is key to our design methodology.

Experimental investigation of a newly designed supersonic wind tunnel

NASA Astrophysics Data System (ADS)

Wu, J.; Radespiel, R.

2015-06-01

The flow characteristics of the tandem nozzle supersonic wind tunnel at the Institute of Fluid Mechanics, Technische Universität Braunschweig, a are investigated. Conventional measurement techniques were utilized. The flow development is examined by pressure sensors installed at various streamwise positions. The temperature is measured in the storage tube and the settling chamber. The influence of flow treatment in the settling chamber on the flow quality is also studied. The flow quality of test section is evaluated by a 6-probe Pitot rake. The pressure fluctuations in the test section are studied by a sharp cone model. Eventually, good agreement between the measurements and numerical simulation of the tunnel design is achieved.

Predictors of Low-Care Prevalence in Florida Nursing Homes: The Role of Medicaid Waiver Programs

ERIC Educational Resources Information Center

Hahn, Elizabeth A.; Thomas, Kali S.; Hyer, Kathryn; Andel, Ross; Meng, Hongdao

2011-01-01

Purpose of the study: To examine the relationship between county-level Medicaid home- and community-based service (HCBS) waiver expenditures and the prevalence of low-care residents in Florida nursing homes (NHs). Design and Methods: The present study used a cross-sectional design. We combined two data sources: NH facility-level data (including…

Rurality and Nursing Home Quality: Evidence from the 2004 National Nursing Home Survey

ERIC Educational Resources Information Center

Kang, Yu; Meng, Hongdao; Miller, Nancy A.

2011-01-01

Purpose of the Study: To evaluate the impact of rural geographic location on nursing home quality of care in the United States. Design and Methods: The study used cross-sectional observational design. We obtained resident- and facility-level data from 12,507 residents in 1,174 nursing homes from the 2004 National Nursing Home Survey. We used…

Development and Validation of an Instrument to Assess Student Attitudes toward Science across Grades 5 through 10

ERIC Educational Resources Information Center

Summers, Ryan; Abd-El-Khalick, Fouad

2018-01-01

The aim of the present study is to enable future studies into students' attitudes toward science, and related constructs, by developing and validating an instrument suitable for cross-sectional designs. Following a thorough review of the literature it was determined that many extant instruments included design aspects that appeared to be limited…

Training Valence, Instrumentality, and Expectancy Scale (T-VIES-it): Factor Structure and Nomological Network in an Italian Sample

ERIC Educational Resources Information Center

Zaniboni, Sara; Fraccaroli, Franco; Truxillo, Donald M.; Bertolino, Marilena; Bauer, Talya N.

2011-01-01

Purpose: The purpose of this study is to validate, in an Italian sample, a multidimensional training motivation measure (T-VIES-it) based on expectancy (VIE) theory, and to examine the nomological network surrounding the construct. Design/methodology/approach: Using a cross-sectional design study, 258 public sector employees in Northeast Italy…

21 CFR 320.26 - Guidelines on the design of a single-dose in vivo bioavailability or bioequivalence study.

Code of Federal Regulations, 2013 CFR

2013-04-01

... delivery systems other than oral or intravenous dosage forms with an appropriate reference standard, the... 21 Food and Drugs 5 2013-04-01 2013-04-01 false Guidelines on the design of a single-dose in vivo bioavailability or bioequivalence study. 320.26 Section 320.26 Food and Drugs FOOD AND DRUG ADMINISTRATION...

21 CFR 320.26 - Guidelines on the design of a single-dose in vivo bioavailability or bioequivalence study.

Code of Federal Regulations, 2012 CFR

2012-04-01

... delivery systems other than oral or intravenous dosage forms with an appropriate reference standard, the... 21 Food and Drugs 5 2012-04-01 2012-04-01 false Guidelines on the design of a single-dose in vivo bioavailability or bioequivalence study. 320.26 Section 320.26 Food and Drugs FOOD AND DRUG ADMINISTRATION...

21 CFR 320.26 - Guidelines on the design of a single-dose in vivo bioavailability or bioequivalence study.

Code of Federal Regulations, 2014 CFR

2014-04-01

... delivery systems other than oral or intravenous dosage forms with an appropriate reference standard, the... 21 Food and Drugs 5 2014-04-01 2014-04-01 false Guidelines on the design of a single-dose in vivo bioavailability or bioequivalence study. 320.26 Section 320.26 Food and Drugs FOOD AND DRUG ADMINISTRATION...

Study of an advanced transport airplane design concept known as Flatbed

NASA Technical Reports Server (NTRS)

Smethers, R. G.; Caldwell, E. W.; Warnock, W. E.; Wilson, J. M., Jr.

1980-01-01

The design concept and configuration of the Flatbed transport aircraft are presented. The Flatbed configuration combines into one frame, the ability to haul cargo, virtually unrestrained by cross sectional dimensions of the fuselage. The feasibility and capability of the Flatbed is discussed in depth.

Design study of a radio-frequency quadrupole for high-intensity beams

NASA Astrophysics Data System (ADS)

Bahng, Jungbae; Kim, Eun-San; Choi, Bong-Hyuk

2017-07-01

The Rare isotope Accelerator Of Newness (RAON) heavy-ion accelerator has been designed for the Rare Isotope Science Project (RISP) in Korea. The RAON will produce heavy-ion beams from 660-MeV-proton to 200-MeV/u-uranium with continuous wave (CW) power of 400 kW to support research in various scientific fields. Its system consists of an ECR ion source, LEBTs with 10 keV/u, CW RFQ accelerator with 81.25 MHz and 500 keV/u, a MEBT system, and a SC linac. In detail, the driver linac system consists of a Quarter Wave Resonator (QWR) section with 81.25 MHz and a Half Wave Resonator (HWR) section with 162.5 MHz, Linac-1, and a Spoke Cavity section with 325 MHz, Linac-2. These linacs have been designed to optimize the beam parameters to meet the required design goals. At the same time, a light-heavy ion accelerator with high-intensity beam, such as proton, deuteron, and helium beams, is required for experiments. In this paper, we present the design study of the high intensity RFQ for a deuteron beam with energies from 30 keV/u to 1.5 MeV/u and currents in the mA range. This system is composed of an Penning Ionization Gauge ion source, short LEBT with a RF deflector, and shared SC Linac. In order to increase acceleration efficiency in a short length with low cost, the 2nd harmonic of 162.5 MHz is applied as the operation frequency in the D+ RFQ design. The D+ RFQ is designed with 4.97 m, 1.52 bravery factor. Since it operates with 2nd harmonic frequency, the beam should be 50% of the duty factor while the cavity should be operated in CW mode, to protect the downstream linac system. We focus on avoiding emittance growth by the space-charge effect and optimizing the RFQ to achieve a high transmission and low emittance growth. Both the RFQ beam dynamics study and RFQ cavity design study for two and three dimensions will be discussed. Supported by Korea University Future Research Grant

Earthquake ground motion: Chapter 3

USGS Publications Warehouse

Luco, Nicolas; Kircher, Charles A.; Crouse, C. B.; Charney, Finley; Haselton, Curt B.; Baker, Jack W.; Zimmerman, Reid; Hooper, John D.; McVitty, William; Taylor, Andy

2016-01-01

Most of the effort in seismic design of buildings and other structures is focused on structural design. This chapter addresses another key aspect of the design process—characterization of earthquake ground motion into parameters for use in design. Section 3.1 describes the basis of the earthquake ground motion maps in the Provisions and in ASCE 7 (the Standard). Section 3.2 has examples for the determination of ground motion parameters and spectra for use in design. Section 3.3 describes site-specific ground motion requirements and provides example site-specific design and MCER response spectra and example values of site-specific ground motion parameters. Section 3.4 discusses and provides an example for the selection and scaling of ground motion records for use in various types of response history analysis permitted in the Standard.

14 CFR 23.335 - Design airspeeds.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Design airspeeds. 23.335 Section 23.335... Design airspeeds. Except as provided in paragraph (a)(4) of this section, the selected design airspeeds are equivalent airspeeds (EAS). (a) Design cruising speed, V C. For V C the following apply: (1) Where...

14 CFR 23.335 - Design airspeeds.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Design airspeeds. 23.335 Section 23.335... Design airspeeds. Except as provided in paragraph (a)(4) of this section, the selected design airspeeds are equivalent airspeeds (EAS). (a) Design cruising speed, V C. For V C the following apply: (1) Where...

47 CFR 80.1252 - Designated entities.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 47 Telecommunication 5 2011-10-01 2011-10-01 false Designated entities. 80.1252 Section 80.1252... MARITIME SERVICES Competitive Bidding Procedures § 80.1252 Designated entities. (a) This section addresses certain issues concerning designated entities in maritime communications services subject to competitive...

47 CFR 80.1252 - Designated entities.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 47 Telecommunication 5 2010-10-01 2010-10-01 false Designated entities. 80.1252 Section 80.1252... MARITIME SERVICES Competitive Bidding Procedures § 80.1252 Designated entities. (a) This section addresses certain issues concerning designated entities in maritime communications services subject to competitive...

Guidelines for the design of subsurface drainage systems for highway structural sections

DOT National Transportation Integrated Search

1972-06-01

Design criteria and a design method for pavement subsurface drainage systems include inflow-outflow method of analysis, open graded drainage layers, collector drains, pipe outlets and markers. Design examples are given for embankment sections, cut se...

Interpersonal Skills and Facebook® Use among College Students

ERIC Educational Resources Information Center

Rhodes, Darson L.; Sniatecki, Jessica L.; Rocco, Mary; Todd, Lauren

2015-01-01

The use of Facebook® among college students is prevalent, and its relationship with interpersonal skills is unknown. A cross-sectional design study using a convenience sample of undergraduate students enrolled in one of four sections of an upper-level nutrition course at a Northeastern, public university was conducted to investigate this…

ACCESS Guide to the Persian Gulf Crisis. Updated Edition.

ERIC Educational Resources Information Center

Young, Stephen, Ed.

This guide for studying the events of the Persian Gulf War is designed to be non-partisan and to promote participation in public debate among concerned citizens, national organizations, educators, researchers, and academics. The guide is divided into four sections. Section 1 provides background information, the text of the United Nations…

Social Studies in the Mainstreamed Classroom, K-6.

ERIC Educational Resources Information Center

Ochoa, Anna S.; Shuster, Susan K.

A guide is designed for elementary school teachers with handicapped students in their classrooms. Seven sections comprise the document. Section I discusses the implications of mainstreaming for classroom teachers. Discussed are 1) the physical and social isolation of the handicapped students in the 1960s; 2) the impact of Public Law 94-142 which…

System-Level Experimental Validations for Supersonic Commercial Transport Aircraft Entering Service in the 2018-2020 Time Period

NASA Technical Reports Server (NTRS)

Magee, Todd E.; Fugal, Spencer R.; Fink, Lawrence E.; Adamson, Eric E.; Shaw, Stephen G.

2015-01-01

This report describes the work conducted under NASA funding for the Boeing N+2 Supersonic Experimental Validation project to experimentally validate the conceptual design of a supersonic airliner feasible for entry into service in the 2018 -to 2020 timeframe (NASA N+2 generation). The primary goal of the project was to develop a low-boom configuration optimized for minimum sonic boom signature (65 to 70 PLdB). This was a very aggressive goal that could be achieved only through integrated multidisciplinary optimization tools validated in relevant ground and, later, flight environments. The project was split into two phases. Phase I of the project covered the detailed aerodynamic design of a low boom airliner as well as the wind tunnel tests to validate that design (ref. 1). This report covers Phase II of the project, which continued the design methodology development of Phase I with a focus on the propulsion integration aspects as well as the testing involved to validate those designs. One of the major airplane configuration features of the Boeing N+2 low boom design was the overwing nacelle. The location of the nacelle allowed for a minimal effect on the boom signature, however, it added a level of difficulty to designing an inlet with acceptable performance in the overwing flow field. Using the Phase I work as the starting point, the goals of the Phase 2 project were to design and verify inlet performance while maintaining a low-boom signature. The Phase II project was successful in meeting all contract objectives. New modular nacelles were built for the larger Performance Model along with a propulsion rig with an electrically-actuated mass flow plug. Two new mounting struts were built for the smaller Boom Model, along with new nacelles. Propulsion integration testing was performed using an instrumented fan face and a mass flow plug, while boom signatures were measured using a wall-mounted pressure rail. A side study of testing in different wind tunnels was completed as a precursor to the selection of the facilities used for validation testing. As facility schedules allowed, the propulsion testing was done at the NASA Glenn Research Center (GRC) 8 x 6-Foot wind tunnel, while boom and force testing was done at the NASA Ames Research Center (ARC) 9 x 7-Foot wind tunnel. During boom testing, a live balance was used for gathering force data. This report is broken down into nine sections. The first technical section (Section 2) covers the general scope of the Phase II activities, goals, a description of the design and testing efforts, and the project plan and schedule. Section 3 covers the details of the propulsion system concepts and design evolution. A series of short tests to evaluate the suitability of different wind tunnels for boom, propulsion, and force testing was also performed under the Phase 2 effort, with the results covered in Section 4. The propulsion integration testing is covered in Section 5 and the boom and force testing in Section 6. CFD comparisons and analyses are included in Section 7. Section 8 includes the conclusions and lessons learned.

Study program for design improvements of the X-3060 klystron. Phase 3: Electron gun fabrication and beam analyzer evaluation. Phase 4: Klystron prototype fabrication and testing

NASA Technical Reports Server (NTRS)

Goldfinger, A.

1981-01-01

A full scale model was produced to verify suggested design changes. Through beam analyzer study, the correct electron beam diameter and cross sectional profile were established in conjunction with the desired confining magnetic field. Comparative data on the performance of the X-3060 klystron, design predictions for the improved klystron, and performance data taken during acceptance testing of the prototype VKS-8274 JPL are presented.

Application of a design-build-team approach to low cost and weight composite fuselage structure

NASA Technical Reports Server (NTRS)

Ilcewicz, L. B.; Walker, T. H.; Willden, K. S.; Swanson, G. D.; Truslove, G.; Metschan, S. L.; Pfahl, C. L.

1991-01-01

Relationships between manufacturing costs and design details must be understood to promote the application of advanced composite technologies to transport fuselage structures. A team approach, integrating the disciplines responsible for aircraft structural design and manufacturing, was developed to perform cost and weight trade studies for a twenty-foot diameter aft fuselage section. Baseline composite design and manufacturing concepts were selected for large quadrant panels in crown, side, and keel areas of the fuselage section. The associated technical issues were also identified. Detailed evaluation of crown panels indicated the potential for large weight savings and costs competitive with aluminum technology in the 1995 timeframe. Different processes and material forms were selected for the various elements that comprise the fuselage structure. Additional cost and weight savings potential was estimated for future advancements.

Design features of a low-disturbance supersonic wind tunnel for transition research at low supersonic Mach numbers

NASA Technical Reports Server (NTRS)

Wolf, Stephen W. D.; Laub, James A.; King, Lyndell S.; Reda, Daniel C.

1992-01-01

A unique, low-disturbance supersonic wind tunnel is being developed at NASA-Ames to support supersonic laminar flow control research at cruise Mach numbers of the High Speed Civil Transport (HSCT). The distinctive design features of this new quiet tunnel are a low-disturbance settling chamber, laminar boundary layers along the nozzle/test section walls, and steady supersonic diffuser flow. This paper discusses these important aspects of our quiet tunnel design and the studies necessary to support this design. Experimental results from an 1/8th-scale pilot supersonic wind tunnel are presented and discussed in association with theoretical predictions. Natural laminar flow on the test section walls is demonstrated and both settling chamber and supersonic diffuser performance is examined. The full-scale wind tunnel should be commissioned by the end of 1993.

Design and evaluation of a bolted joint for a discrete carbon-epoxy rod-reinforced hat section

NASA Technical Reports Server (NTRS)

Rousseau, Carl Q.; Baker, Donald J.

1996-01-01

The use of prefabricated pultruded carbon-epoxy rods has reduced the manufacturing complexity and costs of stiffened composite panels while increasing the damage tolerance of the panels. However, repairability of these highly efficient discrete stiffeners has been a concern. Design, analysis, and test results are presented in this paper for a bolted-joint repair for the pultruded rod concept that is capable of efficiently transferring axial loads in a hat-section stiffener on the upper skin segment of a heavily loaded aircraft wing component. A tension and a compression joint design were evaluated. The tension joint design achieved approximately 1.0% strain in the carbon-epoxy rod-reinforced hat-section and failed in a metal fitting at 166% of the design ultimate load. The compression joint design failed in the carbon-epoxy rod-reinforced hat-section test specimen area at approximately 0.7% strain and at 110% of the design ultimate load. This strain level of 0.7% in compression is similar to the failure strain observed in previously reported carbon-epoxy rod-reinforced hat-section column tests.

Taurus Lightweight Manned Spacecraft Earth orbiting vehicle

NASA Technical Reports Server (NTRS)

Bosset, M.

1991-01-01

The Taurus Lightweight Manned Spacecraft (LMS) was developed by students of the University of Maryland's Aerospace Engineering course in Space Vehicle Design. That course required students to design an Alternative Manned Spacecraft (AMS) to augment or replace the Space Transportation System and meet the following design requirements: (1) launch on the Taurus Booster being developed by Orbital Sciences Corporation; (2) 99.9 percent assured crew survival rate; (3) technology cutoff date of 1 Jan. 1991; (4) compatibility with current space administration infrastructure; and (5) first flight by May 1995. The Taurus LMS design meets the above requirements and represents an initial step toward larger and more complex spacecraft. The Taurus LMS has a very limited application when compared to the space shuttle, but it demonstrates that the U.S. can have a safe, reliable, and low-cost space system. The Taurus LMS is a short mission duration spacecraft designed to place one man into low Earth orbit (LEO). The driving factor for this design was the low payload carrying capabilities of the Taurus Booster - 1300 kg to a 300-km orbit. The Taurus LMS design is divided into six major design sections. The Human Factors section deals with the problems of life support and spacecraft cooling. The Propulsion section contains the Abort System, the Orbital Maneuvering System (OMS), the Reaction Control System (RCS), and Power Generation. The thermal protection systems and spacecraft structure are contained in the Structures section. The Avionics section includes Navigation, Attitude Determination, Data Processing, Communication systems, and Sensors. The Mission Analysis section was responsible for ground processing and spacecraft astrodynamics. The Systems Integration Section pulled the above sections together into one spacecraft, and addressed costing and reliability.

Modular Radioisotope Thermoelectric Generator (RTG) Program. Final technical report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1992-12-31

Section 2.0 of this report summarizes the MOD-RTG reference flight design, and Section 3.0 discusses the Ground Demonstration System design. Multicouple technology development is discussed in Section 4.0, and Section 5.0 lists all published technical papers prepared during the course of the contract.

Factors Influencing Residents' Satisfaction in Residential Aged Care

ERIC Educational Resources Information Center

Chou, Shu-Chiung; Boldy, Duncan P.; Lee, Andy H.

2003-01-01

Purpose: The aim of this study was to identify the important factors influencing residents' satisfaction in residential aged care and to provide a better understanding of their interrelationships. Design and Methods: A cross-sectional survey design was used to collect the required information, including resident satisfaction, resident dependency…

The Hoosier Connection: Grade 8.

ERIC Educational Resources Information Center

Harris, Ira; And Others

This eighth grade teacher's guide with student activities is designed to create greater awareness of Indiana, its geography, history, government, and future and is designed to be used as a supplement to the study of the U.S. Constitution and the Indiana Constitution. In the first section, entitled "Geography of Indiana," the lessons…

Evaluation of pathogen-specific biomarkers for the diagnosis of tuberculosis in white-tailed deer (Odocoileus virginianus)

USDA-ARS?s Scientific Manuscript database

Objective - To develop a noninvasive biomarker based Mycobacterium bovis specific detection system to track infection in domestic and wild animals. Design – Experimental longitudinal study for discovery and cross sectional design for validation Animals - Yearling white-tailed deer fawns (n=8) were ...

Human-Centered Technologies and Procedures for Future Air Traffic Management: A Preliminary Overview of 1996 Studies and Results

NASA Technical Reports Server (NTRS)

Smith, Philip; McCoy, Elaine; Denning, Rebecca; Woods, David; Sarter, Nadine; Dekker, Sidney; Billings, Charles

1996-01-01

In this project, we have been exploring the use of a general methodology to predict the impact of future Air Traffic Management (ATM) concepts and technologies. In applying this methodology, our emphasis has been on the importance of modeling coordination and cooperation among the multiple agents within this system, and on understanding how the interactions among these agents will be influenced as new roles, responsibilities, procedures and technologies are introduced. To accomplish this, we have been collecting data on performance under the current air traffic management system, trying to identify critical problem areas and looking for exemplars suggestive of general approaches for solving such problems. Based on the results of these field studies, we have developed a set of scenarios centered around potential future system designs, and have conducted studies using these scenarios involving a total 40 controllers, dispatchers, pilots and traffic managers. The purpose of this report is to provide NASA with an early summary of the major recommendations that have resulted from our research under the AATT Program thus far. Recommendations 1-3 deal with general approaches that our findings suggest should be incorporated in future AATT Program activities, while Recommendations 4-11 identify some specific topics and technologies that merit research and development activities. Detailed technical reports containing supporting data, as well as the results of our still ongoing analyses, will be provided at a later date. The remainder of this report is organized as follows. Section 1 briefly describes the general design philosophy supported by our empirical studies. Section 2 presents the research methods we have used for identifying requirements for future system designs and for evaluating alternative design solutions. Section 3 discusses preliminary results from an initial set of investigations that we have conducted using these research methods. Section 4 then provides an overall summary. An outline of the rest of this preliminary project summary is provided on the following page.

Toxic Hazards Research Unit 1989

DTIC Science & Technology

1990-10-01

frequently be developed to drive the experimental design and to assist in risk avsessments. The Toxic Hazards Division, Harry G. Armstrong Aerospace...postexposure, respectively. The experimental design (Section 3.3, Subchronic Inhalation Toxicity Studies on 3.1 Oil at Concentrations of 250, 50, and...sodium salt and the pH was adjusted to 7.4. 101 EXPERIMENTAL DESIGN Initiation Assessment A total of seven groups consisting of eight animals per

40 CFR 792.135 - Physical and chemical characterization studies.

Code of Federal Regulations, 2011 CFR

2011-07-01

... studies. 792.135 Section 792.135 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED... A Study § 792.135 Physical and chemical characterization studies. (a) All provisions of the GLPs shall apply to physical and chemical characterization studies designed to determine stability...

Structure reliability design and analysis of support ring for cylinder seal

NASA Astrophysics Data System (ADS)

Minmin, Zhao

2017-09-01

In this paper, the general reliability design process of the cross-sectional dimension of the support ring is introduced, which is used for the cylinder sealing. Then, taking a certain section shape support ring as an example, the every size parameters of section are determined from the view point of reliability design. Last, the static strength and reliability of the support ring are analyzed to verify the correctness of the reliability design result.

47 CFR 90.1103 - Designated entities.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 47 Telecommunication 5 2010-10-01 2010-10-01 false Designated entities. 90.1103 Section 90.1103... Designated entities. (a) This section addresses certain issues concerning designated entities in the Location... provisions. (1) A small business is an entity that, together with its affiliates and controlling interests...

47 CFR 90.1103 - Designated entities.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 47 Telecommunication 5 2011-10-01 2011-10-01 false Designated entities. 90.1103 Section 90.1103... Designated entities. (a) This section addresses certain issues concerning designated entities in the Location... provisions. (1) A small business is an entity that, together with its affiliates and controlling interests...

10 CFR 50.55a - Codes and standards.

Code of Federal Regulations, 2010 CFR

2010-01-01

..., standard design approval, and standard design certification application under part 52 of this chapter is... section. (a)(1) Structures, systems, and components must be designed, fabricated, erected, constructed... Guide 1.84, Revision 34, “Design, Fabrication, and Materials Code Case Acceptability, ASME Section III...

Knowledge Management in Instructional Design. ERIC Digest.

ERIC Educational Resources Information Center

Spector, J. Michael; Edmonds, Gerald S.

This digest reviews what instructional designers do, describes knowledge management, and indicates how knowledge management is influencing instructional design. The first section defines instructional design (ID) and briefly describes the ID process. The second section covers knowledge management (KM), including definitions of KM and systems,…

Radar cross section studies/compact range research

NASA Technical Reports Server (NTRS)

Burnside, W. D.; Dominek, A. K.; Gupta, I. J.; Newman, E. H.; Pathak, P. H.; Peters, L., Jr.

1989-01-01

Achievements in advancing the state-of-the-art in the measurement, control, and analysis of electromagnetic scattering from general aerodynamic targets are summarized. The major topics associated with this study include: (1) electromagnetic scattering analysis; (2) indoor scattering measurement systems; (3) RCS control; (4) waveform processing techniques; (5) material scattering and design studies; (6) design and evaluation of standard targets; and (7) antenna studies. Progress in each of these areas is reported and related publications are listed.

Smoking in Australian University Students and Its Association with Socio-Demographic Factors, Stress, Health Status, Coping Strategies, and Attitude

ERIC Educational Resources Information Center

Sun, Jing; Buys, Nicholas; Stewart, Donald; Shum, David; Farquhar, Lynette

2011-01-01

Purpose: This study aims to evaluate the prevalence of smoking amongst university students in Brisbane, Australia and associated risk factors. Design/methodology/approach: A cross-sectional design was used for the study. A sample of 2,414 university students aged 18-30 was examined to estimate the prevalence of tobacco use. Smoking was measured by…

21 CFR 320.26 - Guidelines on the design of a single-dose in vivo bioavailability or bioequivalence study.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 5 2011-04-01 2011-04-01 false Guidelines on the design of a single-dose in vivo bioavailability or bioequivalence study. 320.26 Section 320.26 Food and Drugs FOOD AND DRUG ADMINISTRATION... test product and the reference material should be administered to subjects in the fasting state, unless...

Design versions of HTS three-phase cables with the minimized value of AC losses

NASA Astrophysics Data System (ADS)

Altov, V. A.; Balashov, N. N.; Degtyarenko, P. N.; Ivanov, S. S.; Kopylov, S. I.; Lipa, DA; Samoilenkov, S. V.; Sytnikov, V. E.; Zheltov, V. V.

2018-03-01

Design versions of HTS three-phase cables consisting of 2G HTS tapes have been investigated by the numerical simulation method with the aim of AC losses minimization. Two design versions of cables with the coaxial and extended rectangular cross-section shape are considered – the non-sectioned and sectioned one. In the latter each cable phase consists of sections connected in parallel. The optimal dimensions of sections and order of their alteration are chosen by appropriate calculations. The model used takes into account the current distribution between the sections and its non-uniformity within each single HTS tape as well. The following characteristics are varied: design version, dimension, positioning of extra copper layer in a cable, design of HTS tapes themselves and their mutual position. The dependence of AC losses on the latter two characteristics is considered in details, and the examples of cable designs optimized by the total set of characteristics for the medium class of voltages (10 – 60 kV) are given. At the critical current JC=5.1 кA per phase and current amplitudes lower than 0.85JC, the level of total AC losses does not exceed the natural cryostat heat losses.

Parametric Study of Fire Performance of Concrete Filled Hollow Steel Section Columns with Circular and Square Cross-Section

NASA Astrophysics Data System (ADS)

Nurfaidhi Rizalman, Ahmad; Tahir, Ng Seong Yap Mahmood Md; Mohammad, Shahrin

2018-03-01

Concrete filled hollow steel section column have been widely accepted by structural engineers and designers for high rise construction due to the benefits of combining steel and concrete. The advantages of concrete filled hollow steel section column include higher strength, ductility, energy absorption capacity, and good structural fire resistance. In this paper, comparison on the fire performance between circular and square concrete filled hollow steel section column is established. A three-dimensional finite element package, ABAQUS, was used to develop the numerical model to study the temperature development, critical temperature, and fire resistance time of the selected composite columns. Based on the analysis and comparison of typical parameters, the effect of equal cross-sectional size for both steel and concrete, concrete types, and thickness of external protection on temperature distribution and structural fire behaviour of the columns are discussed. The result showed that concrete filled hollow steel section column with circular cross-section generally has higher fire resistance than the square section.

Designing an upgrade of the Medley setup for light-ion production and fission cross-section measurements

NASA Astrophysics Data System (ADS)

Jansson, K.; Gustavsson, C.; Al-Adili, A.; Hjalmarsson, A.; Andersson-Sundén, E.; Prokofiev, A. V.; Tarrío, D.; Pomp, S.

2015-09-01

Measurements of neutron-induced fission cross-sections and light-ion production are planned in the energy range 1-40 MeV at the upcoming Neutrons For Science (NFS) facility. In order to prepare our detector setup for the neutron beam with continuous energy spectrum, a simulation software was written using the Geant4 toolkit for both measurement situations. The neutron energy range around 20 MeV is troublesome when it comes to the cross-sections used by Geant4 since data-driven cross-sections are only available below 20 MeV but not above, where they are based on semi-empirical models. Several customisations were made to the standard classes in Geant4 in order to produce consistent results over the whole simulated energy range. Expected uncertainties are reported for both types of measurements. The simulations have shown that a simultaneous precision measurement of the three standard cross-sections H(n,n), 235U(n,f) and 238U(n,f) relative to each other is feasible using a triple layered target. As high resolution timing detectors for fission fragments we plan to use Parallel Plate Avalanche Counters (PPACs). The simulation results have put some restrictions on the design of these detectors as well as on the target design. This study suggests a fissile target no thicker than 2 μm (1.7 mg/cm2) and a PPAC foil thickness preferably less than 1 μm. We also comment on the usability of Geant4 for simulation studies of neutron reactions in this energy range.

Aircraft Maneuvers for the Evaluation of Flying Qualities and Agility. Volume 2. Maneuver Descriptions and Section Guide

DTIC Science & Technology

1993-08-01

Requirements to Design 2 Several of these maneuvers may be suitable for the development of design criteria or tactical utility studies . However, this...research was not intended to be a criteria development effort or a tactical ufiflity study . Instead, a sensitivity between each maneuver and various...utility studies because it contains measure of merit data and pilot comments for numerous desigp parameter variations. The Standard Evaluation

A Longitudinal Study of Memory Advantages in Bilinguals

PubMed Central

Ljungberg, Jessica K.; Hansson, Patrik; Andrés, Pilar; Josefsson, Maria; Nilsson, Lars-Göran

2013-01-01

Typically, studies of cognitive advantages in bilinguals have been conducted previously by using executive and inhibitory tasks (e.g. Simon task) and applying cross-sectional designs. This study longitudinally investigated bilingual advantages on episodic memory recall, verbal letter and categorical fluency during the trajectory of life. Monolingual and bilingual participants (n = 178) between 35–70 years at baseline were drawn from the Betula Prospective Cohort Study of aging, memory, and health. Results showed that bilinguals outperformed monolinguals at the first testing session and across time both in episodic memory recall and in letter fluency. No interaction with age was found indicating that the rate of change across ages was similar for bilinguals and monolinguals. As predicted and in line with studies applying cross-sectional designs, no advantages associated with bilingualism were found in the categorical fluency task. The results are discussed in the light of successful aging. PMID:24023803

[Methodological design for the National Survey Violence Against Women in Mexico].

PubMed

Olaiz, Gustavo; Franco, Aurora; Palma, Oswaldo; Echarri, Carlos; Valdez, Rosario; Herrera, Cristina

2006-01-01

To describe the methodology, the research designs used, the estimation and sample selection, variable definitions, collection instruments, and operative design and analytical procedures for the National Survey Violence Against Women in Mexico. A complex (two-step) cross-sectional study was designed and the qualitative design was carried out using in-depth interviews and participant observation in health care units. We obtained for the quantitative study a total of 26 240 interviews in women users of health services and 2 636 questionnaires for health workers; the survey is representative of the 32 Mexican states. For the qualitative study 26 in-depth interviews were conducted with female users and 60 interviews with health workers in the States of Quintana Roo, Coahuila and the Federal District.

78 FR 13911 - Proposed Revision to Design of Structures, Components, Equipment and Systems

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-01

... Analysis Reports for Nuclear Power Plants: LWR Edition,'' Section 3.7.1, ``Seismic Design Parameters,'' Section 3.7.2, ``Seismic System Analysis,'' Section 3.7.3, ``Seismic Subsystem Analysis,'' Section 3.8.1... and analysis issues, (2) updates to review interfaces to improve the efficiency and consistency of...

30 CFR 756.17 - Approval of the Hopi Tribe's abandoned mine land reclamation plan amendments.

Code of Federal Regulations, 2011 CFR

2011-07-01

... public facilities projects; section II, B(1)(d)(ii), concerning the protection of property; and section... eligible projects; Chairman's Letter of Designation and Hopi Tribe Resolution—Designation of Tribal agency... mineral industry on Tribal lands impacted by coal or mineral development; Section II, G—Reports; Sections...

Man-computer Inactive Data Access System (McIDAS). [design, development, fabrication, and testing

NASA Technical Reports Server (NTRS)

1973-01-01

A technical description is given of the effort to design, develop, fabricate, and test the two dimensional data processing system, McIDAS. The system has three basic sections: an access and data archive section, a control section, and a display section. Areas reported include hardware, system software, and applications software.

Design of a compliant wheel for a miniature rover to be used on Mars

NASA Astrophysics Data System (ADS)

Carroll, Mark; Johnson, Jess; Yong, Jimmy

1991-12-01

The Jet Propulsion Laboratory has identified the need for a compliant wheel for a miniature martian rover vehicle. This wheel must meet requirements of minimum mass, linear radial deflection, and reliability in cryogenic conditions over a five year lifespan. Additionally, axial and tangential deflections must be no more than 10 percent of the radial value. The team designed a wheel by use of finite element and dimensionless parameter analysis. Due to the complex geometry of the wheel, a finite element model describing its behavior was constructed to investigate different wheel configurations. Axial and tangential deflections were greatly reduced but did not meet design criteria. A composite material was selected for its high strength, toughness, fatigue resistance, and damping characteristics. The team chose a Kevlar fiber filled thermoplastic composite. This report is divided into four primary sections. First, the introduction section gives background information, defines the task, and discusses the scope and limitations of the project. Second, the alternative designs section introduces alternative design solutions, addresses advantages and disadvantages of each, and identifies the parameters used to determine the best design. Third, the design solution section introduces the methods used to evaluate the alternates, and gives a description of the design process used. Finally, the conclusion and recommendations section evaluates the wheel design, and offers recommendations pertaining to improvement of the design solution.

Design of a compliant wheel for a miniature rover to be used on Mars

NASA Technical Reports Server (NTRS)

Carroll, Mark; Johnson, Jess; Yong, Jimmy

1991-01-01

The Jet Propulsion Laboratory has identified the need for a compliant wheel for a miniature martian rover vehicle. This wheel must meet requirements of minimum mass, linear radial deflection, and reliability in cryogenic conditions over a five year lifespan. Additionally, axial and tangential deflections must be no more than 10 percent of the radial value. The team designed a wheel by use of finite element and dimensionless parameter analysis. Due to the complex geometry of the wheel, a finite element model describing its behavior was constructed to investigate different wheel configurations. Axial and tangential deflections were greatly reduced but did not meet design criteria. A composite material was selected for its high strength, toughness, fatigue resistance, and damping characteristics. The team chose a Kevlar fiber filled thermoplastic composite. This report is divided into four primary sections. First, the introduction section gives background information, defines the task, and discusses the scope and limitations of the project. Second, the alternative designs section introduces alternative design solutions, addresses advantages and disadvantages of each, and identifies the parameters used to determine the best design. Third, the design solution section introduces the methods used to evaluate the alternates, and gives a description of the design process used. Finally, the conclusion and recommendations section evaluates the wheel design, and offers recommendations pertaining to improvement of the design solution.

Bituminous concrete overlay studies.

DOT National Transportation Integrated Search

1971-01-01

Deflection tests conducted on eight sections of primary highway, both before and after asphaltic concrete resurfacings, were analyzed as a study of the utility of such tests in the design of overlays. The application of tentative traffic and allowabl...

Intravenous volume tomographic pulmonary angiography imaging

NASA Astrophysics Data System (ADS)

Ning, Ruola; Strang, John G.; Chen, Biao; Conover, David L.; Yu, Rongfeng

1999-05-01

This study presents a new intravenous (IV) tomographic angiography imaging technique, called intravenous volume tomographic digital angiography (VTDA) for cross sectional pulmonary angiography. While the advantages of IV-VTDA over spiral CT in terms of volume scanning time and resolution have been validated and reported in our previous papers for head and neck vascular imaging, the superiority of IV-VTDA over spiral CT for cross sectional pulmonary angiography has not been explored yet. The purpose of this study is to demonstrate the advantage of isotropic resolution of IV-VTDA in the x, y and z directions through phantom and animal studies, and to explore its clinical application for detecting clots in pulmonary angiography. A prototype image intensifier-based VTDA imaging system has been designed and constructed by modifying a GE 8800 CT scanner. This system was used for a series of phantom and dog studies. A pulmonary vascular phantom was designed and constructed. The phantom was scanned using the prototype VTDA system for direct 3D reconstruction. Then the same phantom was scanned using a GE CT/i spiral CT scanner using the routine pulmonary CT angiography protocols. IV contrast injection and volume scanning protocols were developed during the dog studies. Both VTDA reconstructed images and spiral CT images of the specially designed phantom were analyzed and compared. The detectability of simulated vessels and clots was assessed as the function of iodine concentration levels, oriented angles, and diameters of the vessels and clots. A set of 3D VTDA reconstruction images of dog pulmonary arteries was obtained with different IV injection rates and isotropic resolution in the x, y and z directions. The results of clot detection studies in dog pulmonary arteries have also been shown. This study presents a new tomographic IV angiography imaging technique for cross sectional pulmonary angiography. The results of phantom and animal studies indicate that IV-VTDA is superior to spiral CT for cross sectional pulmonary angiography.

Developing Communication Skills: General Considerations and Specific Techniques.

ERIC Educational Resources Information Center

Joiner, Elizabeth Garner; Westphal, Patricia Barney, Ed.

This practical book is designed for the classroom teacher of a second or foreign language at any level. The articles are grouped into two distinct but interdependent sections on general considerations and specific techniques. The contents of the first section are as follows: "Moi Tarzan, Vous Jane?: A Study of Communicative Competence" by P.B.…

Lecture notes in economics and mathematical system. Volume 150: Supercritical wing sections 3

NASA Technical Reports Server (NTRS)

Bauer, F.; Garabedian, P.; Korn, D.

1977-01-01

Application of computational fluid dynamics to the design and analysis of supercritical wing sections is discussed. Computer programs used to study the flight of modern aircraft at high subsonic speeds are listed and described. The cascades of shockless transonic airfoils that are expected to increase the efficiency of compressors and turbines are included.

Model Course of Study for Agricultural Programs in Iowa. Preparing for the Future.

ERIC Educational Resources Information Center

Martin, Robert A.; And Others

Each section contained in this packet is necessary for designing an effective program of agriculture education. The curriculum guide that is developed from this model should include the same sections. The model includes: (1) community description; (2) school description; (3) goals and objectives of education in agriculture; (4) evaluation policy;…

WebQuest on Conic Sections as a Learning Tool for Prospective Teachers

ERIC Educational Resources Information Center

Kurtulus, Aytac; Ada, Tuba

2012-01-01

WebQuests incorporate technology with educational concepts through integrating online resources with student-centred and activity-based learning. In this study, we describe and evaluate a WebQuest based on conic sections, which we have used with a group of prospective mathematics teachers. The WebQuest entitled: "Creating a Carpet Design Using…

State Level Programs to Prepare and Use Mental Health Manpower in a State Mental Health Agency.

ERIC Educational Resources Information Center

Southern Regional Education Board, Atlanta, GA.

To assist mental health agency leaders and others concerned with state mental health manpower development, these guidelines (presented in ten sections) explore various issues and approaches and indications for using one approach over another. The first three sections focus on designing and conducting manpower studies, making long range projections…

Psychological Problems in Children with Cerebral Palsy: A Cross-Sectional European Study

ERIC Educational Resources Information Center

Parkes, Jackie; White-Koning, Melanie; Dickinson, Heather O.; Thyen, Ute; Arnaud, Catherine; Beckung, Eva; Fauconnier, Jerome; Marcelli, Marco; McManus, Vicki; Michelsen, Susan I.; Parkinson, Kathryn; Colver, Allan

2008-01-01

Objectives: To describe psychological symptoms in 8-12-year-old children with cerebral palsy; to investigate predictors of these symptoms and their impact on the child and family. Design: A cross-sectional multi-centre survey. Participants: Eight hundred and eighteen children with cerebral palsy, aged 8-12 years, identified from population-based…

Libro de Lectura. Nivel A. (Reading Book. Level A.).

ERIC Educational Resources Information Center

Yeats, Alid; And Others

This is the first in a series of four reading books written in Spanish and designed for use in elementary bilingual education programs. The stories are divided into two main sections, Estudios Sociales (Social Studies) and La Naturaleza (Nature). The five stories in the first section deal with such topics as the home, school, and cleaning. The…

Libro de Lectura. Nivel B. (Reading Book. Level B.).

ERIC Educational Resources Information Center

Yeats, Alid; And Others

This is the second in a series of four reading books written in Spanish and designed for use in elementary bilingual education programs. The stories are divided into two main sections, Estudios Sociales (Social Studies), and La Comunidad (The Community). The stories in the first section have to do with activities in the home, particularly chores…

Study/experimental/research design: much more than statistics.

PubMed

Knight, Kenneth L

2010-01-01

The purpose of study, experimental, or research design in scientific manuscripts has changed significantly over the years. It has evolved from an explanation of the design of the experiment (ie, data gathering or acquisition) to an explanation of the statistical analysis. This practice makes "Methods" sections hard to read and understand. To clarify the difference between study design and statistical analysis, to show the advantages of a properly written study design on article comprehension, and to encourage authors to correctly describe study designs. The role of study design is explored from the introduction of the concept by Fisher through modern-day scientists and the AMA Manual of Style. At one time, when experiments were simpler, the study design and statistical design were identical or very similar. With the complex research that is common today, which often includes manipulating variables to create new variables and the multiple (and different) analyses of a single data set, data collection is very different than statistical design. Thus, both a study design and a statistical design are necessary. Scientific manuscripts will be much easier to read and comprehend. A proper experimental design serves as a road map to the study methods, helping readers to understand more clearly how the data were obtained and, therefore, assisting them in properly analyzing the results.

Joint Study on Some Major Developments in Elementary School Curriculum in Asian and Pacific Countries: Research Design. Report of a Regional Workshop (Tokyo, Japan, February 28-March 15, 1984).

ERIC Educational Resources Information Center

National Inst. for Educational Research, Tokyo (Japan).

A basic framework for undertaking a study of elementary curricula in Pacific and Asian countries is presented. The material, which emerged from a regional workshop, is divided into two sections. A chart in section 1 summarizes major features of elementary school curricula in Australia, Bangladesh, China, India, Japan, Malaysia, Nepal, New Zealand,…

Ram-Jet off Design Performances

NASA Astrophysics Data System (ADS)

Andriani, Roberto; Ghezzi, Umberto

2002-01-01

In this work it is intended to study the off-design performances of a ram jet engine. To this purpouse it has been analyzed in a first time the behaviour of an ideal engine, that means to not consider the losses in the various components, or, under a thermodynamic point of view, to consider the fluid transformation through the air intake and exhaust nozzle, remembering that in a ram jet there are not rotating components as compressor and turbine, isentropic. Referring to the ram-jet scheme of fig.1. we can say, neglecting the fuel introduced, that the air mass flow rate throughout the engine is constant. If we consider the two control sections 4 and 8, respectively the throat section of the converging-diverging supersonic inlet and the throat section of the discharge nozzle, the condition of constant mass flow leads to the relation: m4 =f (M 4 ) m8 = m 4 = m8 We can imaging that the throat section # 4 is always choked for any value of the flight Mach number M0. This means that the throat section 4 is adjusted at any value of M0 so that the flow Mach number in 4 is equal to unity. In this it follows: R. Andriani, U. Ghezzi1 Since in an ideal case T t8 The relation [1] allows to determine the T8 temperature, that represent the maximum cycle temperature, for different operating conditions, as flight Mach number and altitude. We then have two cases: the first is A8 (nozzle throat section) fixed, and the second is A8 variable. In the first case the maximum temperature T8 is univocally determined by the operating condition. In the second case A8 can be varied so to maintain T8 at a chosen value. The graphic of fig.2 shows the first case. In particular it has been considered as design point an altitude of 15000 meters and a flight Mach number equal to 2. In this condition it has been evaluated the section A8 for unity mass flow rate. At the same altitude, varying the flight Mach number, with the section A4 always choked, the graphic shows the variation of the maximum cycle temperature according to the equation *. We notice as the temperature raises to unacceptable levels as we accelerate from the design point. For instance we can see as if we move to flight Mach number 2.2 the maximum temperature raises from 1800 Kelvin degrees (design point) to more than 2900 [K], a value practically unreachable. This shows as the ramjet with fixed discharge nozzle allows very little variation of the operating conditions around the design point. If we consider instead the possibility to vary the nozzle section A8 we can imagine to adjust it so to maintain constant the temperature T8, according to the relation *. The graphics of fig.3 show the area variation required to the section A8 to maintain constant the temperature T8 at the same altitude for different values of the flight Mach number. Considering a circular section, on the same R. Andriani, U. Ghezzi2 picture is reported the corresponding variation of the diameter. On the Y-axis it is reported the ratio between the entity (section and diameter) at the considered condition and at the design point. For the case of A8 section variable it has also been evaluated the behavior of the specific fuel consumption, the mass flow rate and the thrust. In fig.4 they are reported the behavior TSFC and Fuel/air ratio at different flight Mach numbers, and the ratio between them and the design value. In fig .5 it is reported the ratio between the thrust and mass flow rate at different flight conditions and their value at design point. R. Andriani, U. Ghezzi3

Pre-Employment Laboratory Education. Clothing/Fashion Design Guidebook.

ERIC Educational Resources Information Center

Texas Tech Univ., Lubbock. Home Economics Instructional Materials Center.

This guidebook is designed for use in teaching students enrolled in preemployment laboratory education (PELE) clothing/fashion design programs. The first of two major sections includes an overview for teachers on planning, conducting, and evaluating a PELE clothing/fashion design program. Specific topics discussed in section 1 include (1)…

14 CFR 23.1181 - Designated fire zones; regions included.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Designated fire zones; regions included. 23... Powerplant Powerplant Fire Protection § 23.1181 Designated fire zones; regions included. Designated fire zones are— (a) For reciprocating engines— (1) The power section; (2) The accessory section; (3) Any...

14 CFR 23.1181 - Designated fire zones; regions included.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Designated fire zones; regions included. 23... Powerplant Powerplant Fire Protection § 23.1181 Designated fire zones; regions included. Designated fire zones are— (a) For reciprocating engines— (1) The power section; (2) The accessory section; (3) Any...

14 CFR 23.1181 - Designated fire zones; regions included.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Designated fire zones; regions included. 23... Powerplant Powerplant Fire Protection § 23.1181 Designated fire zones; regions included. Designated fire zones are— (a) For reciprocating engines— (1) The power section; (2) The accessory section; (3) Any...

14 CFR 23.1181 - Designated fire zones; regions included.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Designated fire zones; regions included. 23... Powerplant Powerplant Fire Protection § 23.1181 Designated fire zones; regions included. Designated fire zones are— (a) For reciprocating engines— (1) The power section; (2) The accessory section; (3) Any...

14 CFR 23.1181 - Designated fire zones; regions included.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Designated fire zones; regions included. 23... Powerplant Powerplant Fire Protection § 23.1181 Designated fire zones; regions included. Designated fire zones are— (a) For reciprocating engines— (1) The power section; (2) The accessory section; (3) Any...

Pre-Employment Laboratory Education. Home Furnishings/Interior Design Guidebook.

ERIC Educational Resources Information Center

Texas Tech Univ., Lubbock. Home Economics Instructional Materials Center.

This guidebook is designed for use in teaching students enrolled in pre-employment laboratory education (PELE) home furnishing/interior design programs. The first of two major sections includes an overview for teachers on planning, conducting, and evaluating a home furnishings/interior design program. Specific topics discussed in section 1 include…

A Discussion of Knowledge Based Design

NASA Technical Reports Server (NTRS)

Wood, Richard M.; Bauer, Steven X. S.

1999-01-01

A discussion of knowledge and Knowledge- Based design as related to the design of aircraft is presented. The paper discusses the perceived problem with existing design studies and introduces the concepts of design and knowledge for a Knowledge- Based design system. A review of several Knowledge-Based design activities is provided. A Virtual Reality, Knowledge-Based system is proposed and reviewed. The feasibility of Virtual Reality to improve the efficiency and effectiveness of aerodynamic and multidisciplinary design, evaluation, and analysis of aircraft through the coupling of virtual reality technology and a Knowledge-Based design system is also reviewed. The final section of the paper discusses future directions for design and the role of Knowledge-Based design.

Design of a Ku band miniature multiple beam klystron

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bandyopadhyay, Ayan Kumar, E-mail: ayan.bandyopadhyay@gmail.com; Pal, Debasish; Kant, Deepender

2016-03-09

The design of a miniature multiple beam klystron (MBK) working in the Ku-band frequency range is presented in this article. Starting from the main design parameters, design of the electron gun, the input and output couplers and radio frequency section (RF-section) are presented. The design methodology using state of the art commercial electromagnetic design tools, analytical formulae as well as noncommercial design tools are briefly presented in this article.

Design and Evaluation of a Bolted Joint for a Discrete Carbon-Epoxy Rod-Reinforced Hat Section

NASA Technical Reports Server (NTRS)

Baker, Donald J.; Rousseau, Carl Q.

1996-01-01

The use of pre-fabricated pultruded carbon-epoxy rods has reduced the manufacturing complexity and costs of stiffened composite panels while increasing the damage tolerance of the panels. However, repairability of these highly efficient discrete stiffeners has been a concern. Design, analysis, and test results are presented in this paper for a bolted-joint repair for the pultruded rod concept that is capable of efficiently transferring axial loads in a hat-section stiffener on the upper skin segment of a heavily loaded aircraft wing component. A tension and a compression joint design were evaluated. The tension joint design achieved approximately 1.0 percent strain in the carbon-epoxy rod-reinforced hat-section and failed in a metal fitting at 166 percent of the design ultimate load. The compression joint design failed in the carbon-epoxy rod-reinforced hat-section test specimen area at approximately 0.7 percent strain and at 110 percent of the design ultimate load. This strain level of 0.7 percent in compression is similar to the failure strain observed in previously reported carbon-epoxy rod-reinforced hat-section column tests.

Systems design study of the Pioneer Venus spacecraft. Volume 1. Technical analyses and tradeoffs, section 7 (part 3 of 4). [aerodynamic design problems for small probe reentry

NASA Technical Reports Server (NTRS)

1973-01-01

The aerodynamic design problems for the Pioneer Venus mission are discussed for a small probe shape that enters the atmosphere, and exhibits good stability for the subsonic portion of the flight. The problems discussed include: heat shield, structures and mechanisms, thermal control, decelerator, probe communication, data handling and command, and electric power.

Undertaking Experiments in Social Sciences: Sequential, Multiple Time Series Designs for Consideration

ERIC Educational Resources Information Center

Phan, Huy P.; Ngu, Bing H.

2017-01-01

In social sciences, the use of stringent methodological approaches is gaining increasing emphasis. Researchers have recognized the limitations of cross-sectional, non-manipulative data in the study of causality. True experimental designs, in contrast, are preferred as they represent rigorous standards for achieving causal flows between variables.…

Engineering Graphics and Design Teachers' Understanding and Teaching of Assembly Drawing

ERIC Educational Resources Information Center

Singh-Pillay, Asheena; Sotsaka, Douglas Sibusiso

2017-01-01

This study explored the relationship between teachers' content knowledge and their pedagogical skills, and reports on that relationship in the teaching of Assembly Drawing (AD) in a South African context. Given that Engineering Graphics Design (EGD) learners perform poorly in the AD section of the matriculation examination, we need to understand…

Linking Teacher Competences to Organizational Citizenship Behaviour: The Role of Empowerment

ERIC Educational Resources Information Center

Kasekende, Francis; Munene, John C.; Otengei, Samson Omuudu; Ntayi, Joseph Mpeera

2016-01-01

Purpose: The purpose of this paper is to examine relationship between teacher competences and organizational citizenship behavior (OCB) with empowerment as a mediating factor. Design/methodology/approach: The study took a cross-sectional descriptive and analytical design. Using cluster and random sampling procedures, data were obtained from 383…

Radio and Television Repairer Fundamentals. Student's Manual.

ERIC Educational Resources Information Center

Maul, Chuck

This self-contained student manual on fundamentals of radio and television repair is designed to help trade and industrial students relate work experience on the job to information studied at school. Designed for individualized instruction under the supervision of a coordinator or instructor, the manual has 9 sections, each containing 2 to 10…

Parent-Reported Social Support for Child's Fruit and Vegetable Intake: Validity of Measures

ERIC Educational Resources Information Center

Dave, Jayna M.; Evans, Alexandra E.; Condrasky, Marge D.; Williams, Joel E.

2012-01-01

Objective: To develop and validate measures of parental social support to increase their child's fruit and vegetable (FV) consumption. Design: Cross-sectional study design. Setting: School and home. Participants: Two hundred three parents with at least 1 elementary school-aged child. Main Outcome Measure: Parents completed a questionnaire that…

Students' Attitudes towards School-Based Sex and Relationships Education in Tanzania

ERIC Educational Resources Information Center

Mkumbo, Kitila A. K.

2014-01-01

Objective: The objective of this paper was to assess students' attitudes towards school-based sex and relationships education (SRE). Design: This study featured a cross-sectional survey design. Method: A sample of 715 students from two districts in Tanzania completed a survey questionnaire assessing various aspects related to their attitudes…

Stroke Survivors' Evaluations of a Stroke Workbook-Based Intervention Designed to Increase Perceived Control over Recovery

ERIC Educational Resources Information Center

Joice, Sara; Johnston, Marie; Bonetti, Debbie; Morrison, Val; MacWalter, Ron

2012-01-01

Objective: To report stroke survivors' experiences and perceived usefulness of an effective self-help workbook-based intervention. Design: A cross-sectional study involving the intervention group of an earlier randomized controlled trial. Setting: At the participants' homes approximately seven weeks post-hospital discharge. Method: Following the…

Determinants of Low-Fat Eating Behaviors among Midlife African American Women

ERIC Educational Resources Information Center

Evans, Gina L.; McNeil, Lorna H.; Laufman, Larry; Bowman, Sharon L.

2009-01-01

Objective: The purpose of this study was to explore midlife African American women's low-fat eating habits in the context of health attitudes, social support, and food preferences. Design: A cross-sectional design was used. Settings: One Midwestern and 1 national African American women's organization were targeted for data collection.…

Predictors of Paternal and Maternal Controlling Feeding Practices with 2- to 5-Year-Old Children

ERIC Educational Resources Information Center

Haycraft, Emma; Blissett, Jackie

2012-01-01

Objective: This study aimed to identify predictors of controlling feeding practices in both mothers and fathers of young children. Design: Cross-sectional, questionnaire design. Setting: Nursery schools within the United Kingdom recruited participants. Participants: Ninety-six mothers and fathers comprising 48 mother-father pairs of male and…

Sexuality Education in South African Schools: The Challenge for Civil Society Organisations

ERIC Educational Resources Information Center

Adams Tucker, Leigh; George, Gavin; Reardon, Candice; Panday, Saadhna

2017-01-01

Objective: Drawing on the perceptions of various key stakeholders, the paper explores the strengths and limitations of involving civil society organisations in the delivery of HIV and AIDS and sexuality education in South African schools. Design: Qualitative study with a cross-sectional design. Setting: Research was conducted at 16 public…

Development of direct-inverse 3-D methods for applied transonic aerodynamic wing design and analysis

NASA Technical Reports Server (NTRS)

Carlson, Leland A.

1989-01-01

Progress in the direct-inverse wing design method in curvilinear coordinates has been made. This includes the remedying of a spanwise oscillation problem and the assessment of grid skewness, viscous interaction, and the initial airfoil section on the final design. It was found that, in response to the spanwise oscillation problem that designing at every other spanwise station produced the best results for the cases presented, a smoothly varying grid is especially needed for the accurate design at the wing tip, the boundary layer displacement thicknesses must be included in a successful wing design, the design of high and medium aspect ratio wings is possible with this code, and the final airfoil section designed is fairly independent of the initial section.

NRC ARDC Guidance Support Status Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Holbrook, Mark R.

This report provides a summary that reflects the progress and status of proposed regulatory design criteria for advanced non-light water reactor (LWR) designs in accordance with the Level 3 milestone M3AT-17IN2001013 in work package AT-17IN200101. These criteria have been designated as advanced reactor design criteria (ARDC) and they provide guidance to future applicants for addressing the general design criteria (GDC) that are currently applied specifically to LWR designs. This report provides a summary of Phase 2 activities related to the various tasks associated with ARDC development and the subsequent development of ARDC regulatory guidance for sodium fast reactor (SFR) andmore » modular high-temperature gas-cooled reactor (HTGR) designs. Status Report Organization: Section 2 discusses the origin of the GDC and their application to LWRs. Section 3 addresses the objective of this initiative and how it benefits the advanced non-LWR reactor vendors. Section 4 discusses the scope and structure of the initiative. Section 5 provides background on the U.S. Department of Energy (DOE) ARDC team’s original development of the proposed ARDC that were submitted to the NRC for consideration. Section 6 provides a summary of recent ARDC Phase 2 activities. Appendices A through E document the DOE ARDC team’s public comments on various sections of the NRC’s draft regulatory guide DG–1330, “Guidance for Developing Principal Design Criteria for Non-Light Water Reactors.”« less

Development of thermoplastic composite aircraft structures

NASA Technical Reports Server (NTRS)

Renieri, Michael P.; Burpo, Steven J.; Roundy, Lance M.; Todd, Stephanie A.; Kim, H. J.

1992-01-01

Efforts focused on the use of thermoplastic composite materials in the development of structural details associated with an advanced fighter fuselage section with applicability to transport design. In support of these designs, mechanics developments were conducted in two areas. First, a dissipative strain energy approach to material characterization and failure prediction, developed at the Naval Research Laboratory, was evaluated as a design/analysis tool. Second, a finite element formulation for thick composites was developed and incorporated into a lug analysis method which incorporates pin bending effects. Manufacturing concepts were developed for an upper fuel cell cover. A detailed trade study produced two promising concepts: fiber placement and single-step diaphragm forming. Based on the innovative design/manufacturing concepts for the fuselage section primary structure, elements were designed, fabricated, and structurally tested. These elements focused on key issues such as thick composite lugs and low cost forming of fastenerless, stiffener/moldine concepts. Manufacturing techniques included autoclave consolidation, single diaphragm consolidation (SDCC) and roll-forming.

Analysis and Design of Rotors at Ultra-Low Reynolds Numbers

NASA Technical Reports Server (NTRS)

Kunz, Peter J.; Strawn, Roger C.

2003-01-01

Design tools have been developed for ultra-low Reynolds number rotors, combining enhanced actuator-ring / blade-element theory with airfoil section data based on two-dimensional Navier-Stokes calculations. This performance prediction method is coupled with an optimizer for both design and analysis applications. Performance predictions from these tools have been compared with three-dimensional Navier Stokes analyses and experimental data for a 2.5 cm diameter rotor with chord Reynolds numbers below 10,000. Comparisons among the analyses and experimental data show reasonable agreement both in the global thrust and power required, but the spanwise distributions of these quantities exhibit significant deviations. The study also reveals that three-dimensional and rotational effects significantly change local airfoil section performance. The magnitude of this issue, unique to this operating regime, may limit the applicability of blade-element type methods for detailed rotor design at ultra-low Reynolds numbers, but these methods are still useful for evaluating concept feasibility and rapidly generating initial designs for further analysis and optimization using more advanced tools.

Watershed-based survey designs

USGS Publications Warehouse

Detenbeck, N.E.; Cincotta, D.; Denver, J.M.; Greenlee, S.K.; Olsen, A.R.; Pitchford, A.M.

2005-01-01

Watershed-based sampling design and assessment tools help serve the multiple goals for water quality monitoring required under the Clean Water Act, including assessment of regional conditions to meet Section 305(b), identification of impaired water bodies or watersheds to meet Section 303(d), and development of empirical relationships between causes or sources of impairment and biological responses. Creation of GIS databases for hydrography, hydrologically corrected digital elevation models, and hydrologic derivatives such as watershed boundaries and upstream–downstream topology of subcatchments would provide a consistent seamless nationwide framework for these designs. The elements of a watershed-based sample framework can be represented either as a continuous infinite set defined by points along a linear stream network, or as a discrete set of watershed polygons. Watershed-based designs can be developed with existing probabilistic survey methods, including the use of unequal probability weighting, stratification, and two-stage frames for sampling. Case studies for monitoring of Atlantic Coastal Plain streams, West Virginia wadeable streams, and coastal Oregon streams illustrate three different approaches for selecting sites for watershed-based survey designs.

Infrared sensor and window system issues

NASA Astrophysics Data System (ADS)

Hargraves, Charles H., Jr.; Martin, James M.

1992-12-01

EO/IR windows are a significant challenge for the weapon system sensor designer who must design for high EO performance, low radar cross section (RCS), supersonic flight, durability, producibility and affordable initial and life cycle costs. This is particularly true in the 8 to 12 micron IR band at which window materials and coating choices are limited by system design requirements. The requirements also drive the optimization of numerous mechanical, optical, materials, and electrical parameters. This paper addresses the EO/IR window as a system design challenge. The interrelationship of the optical, mechanical, and system design processes are examined. This paper presents a summary of the test results, trade studies and analyses that were performed for multi-segment, flight-worthy optical windows with superior optical performance at subsonic and supersonic aircraft velocities and reduced radar cross section. The impact of the window assembly on EO system modulation transfer function (MTF) and sensitivity will be discussed. The use of conductive coatings for shielding/signature control will be discussed.

Knowledge-based system for detailed blade design of turbines

NASA Astrophysics Data System (ADS)

Goel, Sanjay; Lamson, Scott

1994-03-01

A design optimization methodology that couples optimization techniques to CFD analysis for design of airfoils is presented. This technique optimizes 2D airfoil sections of a blade by minimizing the deviation of the actual Mach number distribution on the blade surface from a smooth fit of the distribution. The airfoil is not reverse engineered by specification of a precise distribution of the desired Mach number plot, only general desired characteristics of the distribution are specified for the design. Since the Mach number distribution is very complex, and cannot be conveniently represented by a single polynomial, it is partitioned into segments, each of which is characterized by a different order polynomial. The sum of the deviation of all the segments is minimized during optimization. To make intelligent changes to the airfoil geometry, it needs to be associated with features observed in the Mach number distribution. Associating the geometry parameters with independent features of the distribution is a fairly complex task. Also, for different optimization techniques to work efficiently the airfoil geometry needs to be parameterized into independent parameters, with enough degrees of freedom for adequate geometry manipulation. A high-pressure, low reaction steam turbine blade section was optimized using this methodology. The Mach number distribution was partitioned into pressure and suction surfaces and the suction surface distribution was further subdivided into leading edge, mid section and trailing edge sections. Two different airfoil representation schemes were used for defining the design variables of the optimization problem. The optimization was performed by using a combination of heuristic search and numerical optimization. The optimization results for the two schemes are discussed in the paper. The results are also compared to a manual design improvement study conducted independently by an experienced airfoil designer. The turbine blade optimization system (TBOS) is developed using the described methodology of coupling knowledge engineering with multiple search techniques for blade shape optimization. TBOS removes a major bottleneck in the design cycle by performing multiple design optimizations in parallel, and improves design quality at the same time. TBOS not only improves the design but also the designers' quality of work by taking the mundane repetitive task of design iterations away and leaving them more time for innovative design.

Design and calibration of the mixing layer and wind tunnel

NASA Technical Reports Server (NTRS)

Bell, James H.; Mehta, Rabindra D.

1989-01-01

A detailed account of the design, assembly and calibration of a wind tunnel specifically designed for free-shear layer research is contained. The construction of this new facility was motivated by a strong interest in the study of plane mixing layers with varying initial and operating conditions. The Mixing Layer Wind tunnel is located in the Fluid Mechanics Laboratory at NASA Ames Research Center. The tunnel consists of two separate legs which are driven independently by centrifugal blowers connected to variable speed motors. The blower/motor combinations are sized such that one is smaller than the other, giving maximum flow speeds of about 20 and 40 m/s, respectively. The blower speeds can either be set manually or via the Microvax II computer. The two streams are allowed to merge in the test section at the sharp trailing edge of a slowly tapering splitter plate. The test section is 36 cm in the cross-stream direction, 91 cm in the spanwise direction and 366 cm in length. One test section side-wall is slotted for probe access and adjustable so that the streamwise pressure gradient may be controlled. The wind tunnel is also equipped with a computer controlled, three-dimensional traversing system which is used to investigate the flow fields with pressure and hot-wire instrumentation. The wind tunnel calibration results show that the mean flow in the test section is uniform to within plus or minus 0.25 pct and the flow angularity is less than 0.25 deg. The total streamwise free-stream turbulence intensity level is approximately 0.15 pct. Currently the wind tunnel is being used in experiments designed to study the three-dimensional structure of plane mixing layers and wakes.

Taurus lightweight manned spacecraft Earth orbiting vehicle

NASA Technical Reports Server (NTRS)

Chase, Kevin A.; Vandersall, Eric J.; Plotkin, Jennifer; Travisano, Jeffrey J.; Loveless, Dennis; Kaczmarek, Michael; White, Anthony G.; Est, Andy; Bulla, Gregory; Henry, Chris

1991-01-01

The Taurus Lightweight Manned Spacecraft (LMS) was developed by students of the University of Maryland's Aerospace Engineering course in Space Vehicle Design. That course required students to design an Alternative Manned Spacecraft (AMS) to augment or replace the Space Transportation System and meet the following design requirements: (1) launch on the Taurus Booster being developed by Orbital Sciences Corporation; (2) 99.9 percent assured crew survival rate; (3) technology cutoff data of 1 Jan. 1991; (4) compatibility with current space administration infrastructure; and (5) first flight by May 1995. The Taurus LMS design meets the above requirements and represents an initial step towards larger and more complex spacecraft. The Taurus LMS has a very limited application when compared to the Space Shuttle, but it demonstrates that the U.S. can have a safe, reliable, and low cost space system. The Taurus LMS is a short mission duration spacecraft designed to place one man into low earth orbit (LEO). The driving factor for this design was the low payload carrying capabilities of the Taurus Booster--1300 kg to a 300 km orbit. The Taurus LMS design is divided into six major design sections. The human factors system deals with the problems of life support and spacecraft cooling. The propulsion section contains the abort system, the Orbital Maneuvering System (OMS), the Reaction Control System (RCS), and power generation. The thermal protection systems and spacecraft structure are contained in the structures section. The avionics section includes navigation, attitude determination, data processing, communication systems, and sensors. The mission analysis section was responsible for ground processing and spacecraft astrodynamics. The systems integration section pulled the above sections together into one spacecraft and addressed costing and reliability.

Designing Computerized Provider Order Entry Software in Iran: The Nurses' and Physicians' Viewpoints.

PubMed

Khammarnia, Mohammad; Sharifian, Roxana; Zand, Farid; Keshtkaran, Ali; Barati, Omid

2016-09-01

This study aimed to identify the functional requirements of computerized provider order entry software and design this software in Iran. This study was conducted using review documentation, interview, and focus group discussions in Shiraz University of Medical Sciences, as the medical pole in Iran, in 2013-2015. The study sample consisted of physicians (n = 12) and nurses (n = 2) in the largest hospital in the southern part of Iran and information technology experts (n = 5) in Shiraz University of Medical Sciences. Functional requirements of the computerized provider order entry system were examined in three phases. Finally, the functional requirements were distributed in four levels, and accordingly, the computerized provider order entry software was designed. The software had seven main dimensions: (1) data entry, (2) drug interaction management system, (3) warning system, (4) treatment services, (5) ability to write in software, (6) reporting from all sections of the software, and (7) technical capabilities of the software. The nurses and physicians emphasized quick access to the computerized provider order entry software, order prescription section, and applicability of the software. The software had some items that had not been mentioned in other studies. Ultimately, the software was designed by a company specializing in hospital information systems in Iran. This study was the first specific investigation of computerized provider order entry software design in Iran. Based on the results, it is suggested that this software be implemented in hospitals.

Laser program annual report, 1980

DOE Office of Scientific and Technical Information (OSTI.GOV)

Coleman, L.W.; Krupke, W.F.; Strack, J.R.

1981-06-01

Volume 2 contains five sections that cover the areas of target design, target fabrication, diagnostics, and fusion experiments. Section 3 reports on target design activities, plasma theory and simulation, code development, and atomic theory. Section 4 presents the accomplishments of the Target Fabrication Group, Section 5 contains the results of our diagnostics development, and Section 6 describes advances made in the management and analysis of experimental data. Finally, Section 7 in Volume 2 reports the results of laser target experiments conducted during the year.

Interim Design Report for the International Design Study for a Neutrino Factory

DOE Office of Scientific and Technical Information (OSTI.GOV)

Choubey, S.; Gandhi, R.; Goswami, S.

2011-10-01

The starting point for the International Design Study for the Neutrino Factory (the IDS-NF) was the output of the earlier International Scoping Study for a future Neutrino Factory and super-beam facility (the ISS). The accelerator facility described in section 2 incorporates the improvements that have been derived from the substantial amount of work carried out within the Accelerator Working Group. Highlights of these improvements include: (1) Initial concepts for the implementation of the proton driver at each of the three example sites, CERN, FNAL, and RAL; (2) Detailed studies of the energy deposition in the target area; (3) A reductionmore » in the length of the muon beam phase-rotation and bunching systems; (4) Detailed analyses of the impact of the risk that stray magnetic field in the accelerating cavities in the ionization cooling channel will reduce the maximum operating gradient. Several alternative ionization-cooling lattices have been developed as fallback options to mitigate this technical risk; (5) Studies of particle loss in the muon front-end and the development of strategies to mitigate the deleterious effects of such losses; (6) The development of more complete designs for the muon linac and re-circulating linacs; (7) The development of a design for the muon FFAG that incorporates insertions for injection and extraction; and (8) Detailed studies of diagnostics in the decay ring. Other sub-systems have undergone a more 'incremental' evolution; an indication that the design of the Neutrino Factory has achieved a degree of maturity. The design of the neutrino detectors described in section 3 has been optimized and the Detector Working Group has made substantial improvements to the simulation and analysis of the Magnetized Iron Neutrino Detector (MIND) resulting in an improvement in the overall neutrino-detection efficiency and a reduction in the neutrino-energy threshold. In addition, initial consideration of the engineering of the MIND has generated a design that is feasible and a finite element analysis of the toroidal magnetic field to produce a realistic field map has been carried out. Section 3 also contains, for the first time, a specification for the near-detector systems and a demonstration that the neutrino flux can be determined with a precision of 1% through measurements of inverse muon decay at the near detector. The performance of the facility, the work of the Physics and Performance Evaluation Group, is described in section 1. The effect of the improved MIND performance is to deliver a discovery reach for CP-invariance violation in the lepton sector, the determination of the mass hierarchy, and of {theta}{sub 13} that extends down to values of sin{sup 2} 2{theta}{sub 13} {approx} 5 x 10{sup -5} and is robust against systematic uncertainties. In addition, the improved neutrino-energy threshold has allowed an indicative analysis of the kind of re-optimization of the facility that could be carried out should {theta}{sub 13} be found close to the current upper bound. The results presented in section 1 demonstrate that the discovery reach as well as the precision with which the oscillation parameters can be measured at the baseline Neutrino Factory is superior to that of other proposed facilities for all possible values of sin{sup 2} 2{theta}{sub 13}.« less

Energy efficient engine: Low-pressure turbine subsonic cascade component development and integration program

NASA Technical Reports Server (NTRS)

Sharma, O. P.; Kopper, F. C.; Knudsen, L. K.; Yustinich, J. B.

1982-01-01

A subsonic cascade test program was conducted to provide technical data for optimizing the blade and vane airfoil designs for the Energy Efficient Engine Low-Pressure Turbine component. The program consisted of three parts. The first involved an evaluation of the low-chamber inlet guide vane. The second, was an evaluation of two candidate aerodynamic loading philosophies for the fourth blade root section. The third part consisted of an evaluation of three candidate airfoil geometries for the fourth blade mean section. The performance of each candidate airfoil was evaluated in a linear cascade configuration. The overall results of this study indicate that the aft-loaded airfoil designs resulted in lower losses which substantiated Pratt & Whitney Aircraft's design philosophy for the Energy Efficient Engine low-pressure turbine component.

Software Design Document SAF Workstation. Volume 1, Sections 1.0 - 2.4. 3.4.86

DTIC Science & Technology

1991-06-01

SLECT TERMS IS. NUMER OF PAGES SIMNET Software Design Document for the SAF Workstation CSCI (CSCI 6). 14. PRICE CODE SECUWItY CLASSIFICATION Is. SECUJRITY...AD-A244 972 SOFTWARE DESIGN DOCUMENT SAF Workstation CSCI (6) Volume 1 of 2 Sections 1.0 - 2.4.3.4.86 DTIC June, 1991 Flt. FCTE S JAN 09 1992...00247 APPROVED FOR PUBLIC RELEASE DISTRBUTION UNLIMITED -Mono SOFTWARE DESIGN DOCUMENT SAF Workstation CSCI (6) Volume 1 of 2 Sections 1.0 - 2.4.3.4.86

Public Interest in Medical Research Participation: Does It Matter if Patients or Community Members Have Helped Design the Study?

PubMed

Cobb, Enesha M; Gebremariam, Achamyeleh; Singer, Dianne; Davis, Matthew M

2015-10-01

We determined national levels of public participation in medical research study design. We compared public interest in medical research participation (MRP) in studies overall, versus studies explicitly designed with public involvement. Cross-sectional household survey of US population in June 2013. Descriptive statistics estimated participation in medical research study design. Chi-square test compared levels of interest in MRP if respondent knew patients or community members helped design the study. Of 2,048 respondents (participation rate 60%), 5% knew someone who had helped design a medical research study. There was no association between having known someone or personal participation in study design and willingness to engage in MRP. Although the overall proportion of respondents who would consider MRP initially (51%) was similar to the proportion who would consider MRP with community member involvement in study design (49%), the changes in respondents' views across the different scenarios were significantly greater than what would have been expected by chance. We found similar levels of interest in MRP whether or not the public is involved in medical research study design. This finding may indicate that public involvement in study design, like community-based participatory research, may not affect overall rates of MRP. © 2015 Wiley Periodicals, Inc.

Laser program annual report, 1979

DOE Office of Scientific and Technical Information (OSTI.GOV)

Coleman, L.W.; Strack, J.R.

1980-03-01

This volume contains four sections that covers the areas of target design, target fabrication, diagnostics, and experiments. Section 3 reports on target design activities, plasma theory and simulation, code development, and atomic theory. Section 4 presents the accomplishments of the target fabrication group, and Section 5 presents results of diagnostic developments and applications for the year. The results of laser-target experiments are presented. (MOW)

Structural design of composite rotor blades with consideration of manufacturability, durability, and manufacturing uncertainties

NASA Astrophysics Data System (ADS)

Li, Leihong

A modular structural design methodology for composite blades is developed. This design method can be used to design composite rotor blades with sophisticate geometric cross-sections. This design method hierarchically decomposed the highly-coupled interdisciplinary rotor analysis into global and local levels. In the global level, aeroelastic response analysis and rotor trim are conduced based on multi-body dynamic models. In the local level, variational asymptotic beam sectional analysis methods are used for the equivalent one-dimensional beam properties. Compared with traditional design methodology, the proposed method is more efficient and accurate. Then, the proposed method is used to study three different design problems that have not been investigated before. The first is to add manufacturing constraints into design optimization. The introduction of manufacturing constraints complicates the optimization process. However, the design with manufacturing constraints benefits the manufacturing process and reduces the risk of violating major performance constraints. Next, a new design procedure for structural design against fatigue failure is proposed. This procedure combines the fatigue analysis with the optimization process. The durability or fatigue analysis employs a strength-based model. The design is subject to stiffness, frequency, and durability constraints. Finally, the manufacturing uncertainty impacts on rotor blade aeroelastic behavior are investigated, and a probabilistic design method is proposed to control the impacts of uncertainty on blade structural performance. The uncertainty factors include dimensions, shapes, material properties, and service loads.

Age Differences in the Monitoring of Learning: Cross-Sectional Evidence of Spared Resolution across the Adult Life Span

ERIC Educational Resources Information Center

Hertzog, Christopher; Sinclair, Starlette M.; Dunlosky, John

2010-01-01

Researchers of metacognitive development in adulthood have exclusively used extreme-age-groups designs. We used a full cross-sectional sample (N = 285, age range: 18-80) to evaluate how associative relatedness and encoding strategies influence judgments of learning (JOLs) in adulthood. Participants studied related and unrelated word pairs and made…

Parent Choice: A Digest of the Research. [Parent Choice and the Public Schools: Volume 1].

ERIC Educational Resources Information Center

Zerchykov, Ross

This guide, first in a series of four volumes, is designed to give information to parents and other decision makers on costs and benefits of different kinds of choices of schools that children might attend. Four sections present digests of information based on research and evaluation studies. Section 1 introduces the format and purpose of the…

If You Record It, Some Won't Come: Using Lecture Capture in Introductory Psychology

ERIC Educational Resources Information Center

Drouin, Michelle A.

2014-01-01

In this study, I examined the effects of offering supplemental video lecture recordings to students in a face-to-face introductory psychology course. I employed a quasi-experimental design, in which one section had lectures recordings available (recordings of the face-to-face lecture) and one section did not, and I examined whether class section…

Criterion-Related Validity of the TOEFL iBT Listening Section. TOEFL iBT Research Report. RR-09-02

ERIC Educational Resources Information Center

Sawaki, Yasuyo; Nissan, Susan

2009-01-01

The study investigated the criterion-related validity of the "Test of English as a Foreign Language"[TM] Internet-based test (TOEFL[R] iBT) Listening section by examining its relationship to a criterion measure designed to reflect language-use tasks that university students encounter in everyday academic life: listening to academic…

The Influence of Study Away Experiences on Global Perspective-Taking

ERIC Educational Resources Information Center

Engberg, Mark E.

2013-01-01

This article examines the relationship between 2 study away experiences--study abroad and service-learning--and the development of a global perspective. Three different studies are presented using cross-sectional and longitudinal designs and multi-institutional samples. The results specifically link involvement in study abroad and service-learning…

In search of causality: a systematic review of the relationship between the built environment and physical activity among adults

PubMed Central

2011-01-01

Background Empirical evidence suggests that an association between the built environment and physical activity exists. This evidence is mostly derived from cross-sectional studies that do not account for other causal explanations such as neighborhood self-selection. Experimental and quasi-experimental designs can be used to isolate the effect of the built environment on physical activity, but in their absence, statistical techniques that adjust for neighborhood self-selection can be used with cross-sectional data. Previous reviews examining the built environment-physical activity relationship have not differentiated among findings based on study design. To deal with self-selection, we synthesized evidence regarding the relationship between objective measures of the built environment and physical activity by including in our review: 1) cross-sectional studies that adjust for neighborhood self-selection and 2) quasi-experiments. Method In September 2010, we searched for English-language studies on built environments and physical activity from all available years in health, leisure, transportation, social sciences, and geographical databases. Twenty cross-sectional and 13 quasi-experimental studies published between 1996 and 2010 were included in the review. Results Most associations between the built environment and physical activity were in the expected direction or null. Land use mix, connectivity and population density and overall neighborhood design were however, important determinants of physical activity. The built environment was more likely to be associated with transportation walking compared with other types of physical activity including recreational walking. Three studies found an attenuation in associations between built environment characteristics and physical activity after accounting for neighborhood self-selection. Conclusion More quasi-experiments that examine a broader range of environmental attributes in relation to context-specific physical activity and that measure changes in the built environment, neighborhood preferences and their effect on physical activity are needed. PMID:22077952

Development of Accomodation Models for Soldiers in Vehicles: Driver

DTIC Science & Technology

2014-09-01

human needs and performance. A small section of this standard addresses the design of vehicle seats and the layout of the driver workstation...drivers and passengers (squad). The study was designed to focus on tactical vehicle (truck) designs with fixed driver heel points and H30 values...fore-aft and vertically, along with adjusting the seat back angle, to obtain a comfortable driving position. The Soldier’s posture and seat adjustments

78 FR 58609 - Proposed Collection; Comment Request for Regulation Project

Federal Register 2010, 2011, 2012, 2013, 2014

2013-09-24

... Designated Roth Contributions to Cash or Deferred Arrangements Under Section 401(k). DATES: Written comments... . SUPPLEMENTARY INFORMATION: Title: Designated Roth Contributions to Cash or Deferred Arrangements Under Section... regulations provide guidance concerning the requirements for designated Roth contributions to qualified cash...

A Systematic Review of Yoga for Balance in a Healthy Population

PubMed Central

Nkodo, Amélie-Françoise; Moonaz, Steffany Haaz; Dagnelie, Gislin

2014-01-01

Abstract Objective: A systematic review was done of the evidence on yoga for improving balance. Design: Relevant articles and reviews were identified in major databases (PubMed, MEDLINE®, IndMed, Web of Knowledge, EMBASE, EBSCO, Science Direct, and Google Scholar), and their reference lists searched. Key search words were yoga, balance, proprioception, falling, fear of falling, and falls. Included studies were peer-reviewed articles published in English before June 2012, using healthy populations. All yoga styles and study designs were included. Two (2) raters individually rated study quality using the Downs & Black (DB) checklist. Final scores were achieved by consensus. Achievable scores ranged from 0 to 27. Effect size (ES) was calculated where possible. Results: Fifteen (15) of 152 studies (age range 10–93, n=688) met the inclusion criteria: 5 randomized controlled trials (RCTs), 4 quasi-experimental, 2 cross-sectional, and 4 single-group designs. DB scores ranged from 10 to 24 (RCTs), 14–19 (quasi-experimental), 6–12 (cross-sectional), and 11–20 (single group). Studies varied by yoga style, frequency of practice, and duration. Eleven (11) studies found positive results (p<0.05) on at least one balance outcome. ES ranged from −0.765 to 2.71 (for 8 studies) and was not associated with DB score. Conclusions: Yoga may have a beneficial effect on balance, but variable study design and poor reporting quality obscure the results. Balance as an outcome is underutilized, and more probing measures are needed. PMID:24517304

Bibliometric analysis of scientific articles published in Brazilian and international orthodontic journals over a 10-year period.

PubMed

Primo, Neudí Antonio; Gazzola, Vivian Bertoglio; Primo, Bruno Tochetto; Tovo, Maximiano Ferreira; Faraco, Italo Medeiros

2014-01-01

This study aimed at describing the profiles of Brazilian and international studies published in orthodontic journals. The sample comprised 635 articles selected from two scientific journals, i.e., Dental Press Journal of Orthodontics and American Journal of Orthodontics and Dentofacial Orthopedics, which were analyzed at three different intervals over a 10-year period (1999 - 2004 - 2009). Articles were described in terms of knowledge domain, study design, and country of origin (or state of origin for Brazilian papers). The most frequent study designs adopted in international studies were cohort (23.9%) and cross-sectional (21.7%) designs. Among Brazilian papers, cross-sectional studies (28.9%) and literature reviews (24.6%) showed greater frequency. The topics most often investigated in international articles were dental materials (17%) and treatment devices (12.4%), with the latter topic being addressed by 16% of the Brazilian publications, followed by malocclusion, with 12.6%. In all cases, the most frequent countries of origin coincided with the countries of origin of each journal. The majority of the studies analyzed featured a low level of scientific evidence. Moreover, the findings showed that journals tend to publish studies produced in their own country of origin, and that there are marked discrepancies in the number of papers published by different Brazilian states.

78 FR 45011 - Designation of Bulut Yayla, AKA: Samet Ince as a Specially Designated Global Terrorist Pursuant...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-25

... DEPARTMENT OF STATE [Public Notice 8390] Designation of Bulut Yayla, AKA: Samet Ince as a Specially Designated Global Terrorist Pursuant to Section 1(b) of Executive Order 13224, as Amended Acting under the authority of and in accordance with section 1(b) of Executive Order 13224 of September 23...

26 CFR 1.468B - Designated settlement funds.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 26 Internal Revenue 6 2010-04-01 2010-04-01 false Designated settlement funds. 1.468B Section 1... (CONTINUED) INCOME TAXES Taxable Year for Which Deductions Taken § 1.468B Designated settlement funds. A designated settlement fund, as defined in section 468B(d)(2), is taxed in the manner described in § 1.468B-2...

Improving the Spelling Ability among Speakers of African American English through Explicit Instruction

ERIC Educational Resources Information Center

Pittman, Ramona T.; Joshi, R. Malatesha; Carreker, Suzanne

2014-01-01

The purpose of this eight week study was to provide explicit instruction to improve spelling to 124 sixth grade students who are speakers of African American English (AAE). Two classroom teachers taught 14 different language arts class sections. The research design was a pretest/posttest/posttest design using wait-list-control. The treatment group…

76 FR 38658 - Agency Information Collection Activities; Submission for Office of Management and Budget Review...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-01

.... One question related to the test DTC advertisements to be used in the study. (Response) We agree that... level (from smallest to largest effect) will be manipulated in one design, and the risk level (from...) demonstrates that information presented with section headings, graphics (such as bullets), and other design...

Total Quality Management in Secondary Schools in Kenya: Extent of Practice

ERIC Educational Resources Information Center

Ngware, Moses Waithanji; Wamukuru, David Kuria; Odebero, Stephen Onyango

2006-01-01

Purpose: To investigate the extent to which secondary schools practiced aspects of total quality management (TQM). Design/methodology/approach: A cross-sectional research design was used in this study. A sample of 300 teachers in a residential session during a school holiday provided their perceptions on the practice of TQM in their schools. Data…

Children's Perceptions of Illness and Health: An Analysis of Drawings

ERIC Educational Resources Information Center

Mouratidi, Paraskevi-Stavroula; Bonoti, Fotini; Leondari, Angeliki

2016-01-01

Objective: The purpose of this study was to explore possible age differences in children's perceptions of illness and health and to what extent these differ from adults' perceptions. Design: Cross-sectional design. Setting: Selected nursery and primary schools in Greece. Method: The sample consisted of 347 children aged 5-11 years and 114…

Organizational and Individual Conditions Associated with Depressive Symptoms among Nursing Home Residents over Time

ERIC Educational Resources Information Center

Cassie, Kimberly M.; Cassie, William E.

2012-01-01

Purpose: To examine the effect of organizational culture and climate on depressive symptoms among nursing home residents. Design and Methods: Using a pooled cross-sectional design, this study examines a sample of 23 nursing homes, 1,114 employees, and 5,497 residents. Depressive symptoms were measured using the Minimum Data Set, Depression Rating…

Networking and Managers' Career Success in the Malaysian Public Sector: The Moderating Effect of Managerial Level

ERIC Educational Resources Information Center

Rasdi, Roziah Mohd; Garavan, Thomas N.; Ismail, Maimunah

2012-01-01

Purpose: The purpose of this paper is to investigate how managerial level moderates the relationships between networking behaviours and career success (objective and subjective) in the context of a public sector organisation in Malaysia. Design/methodology/approach: The study utilised a cross-sectional design and investigated these relationships…

Evaluating the Determinants of Sugary Beverage Consumption among Overweight and Obese Adults: An Application of the Integrative Model of Behavioural Prediction

ERIC Educational Resources Information Center

Collado-Rivera, Maria; Branscum, Paul; Larson, Daniel; Gao, Haijuan

2018-01-01

Objective: The objective of this study was to evaluate the determinants of sugary drink consumption among overweight and obese adults attempting to lose weight using the Integrative Model of Behavioural Prediction (IMB). Design: Cross-sectional design. Method: Determinants of behavioural intentions (attitudes, perceived norms and perceived…

Design in Context: A Conceptual Framework for the Study of Computer Software in Higher Education.

ERIC Educational Resources Information Center

Kozma, Robert B.; Bangert-Drowns, Robert L.

The conceptual groundwork needed to examine the impact of technology, primarily microcomputers, on student learning is presented. Medium, method, and context are tied with a science of design. In section I, research on technology in higher education is reviewed, medium and method are defined, and interaction with context is discussed. Taxonomies…

Impact of carotid stent cell design on vessel scaffolding: a case study comparing experimental investigation and numerical simulations.

PubMed

Conti, Michele; Van Loo, Denis; Auricchio, Ferdinando; De Beule, Matthieu; De Santis, Gianluca; Verhegghe, Benedict; Pirrelli, Stefano; Odero, Attilio

2011-06-01

To quantitatively evaluate the impact of carotid stent cell design on vessel scaffolding by using patient-specific finite element analysis of carotid artery stenting (CAS). The study was organized in 2 parts: (1) validation of a patient-specific finite element analysis of CAS and (2) evaluation of vessel scaffolding. Micro-computed tomography (CT) images of an open-cell stent deployed in a patient-specific silicone mock artery were compared with the corresponding finite element analysis results. This simulation was repeated for the closed-cell counterpart. In the second part, the stent strut distribution, as reflected by the inter-strut angles, was evaluated for both cell types in different vessel cross sections as a measure of scaffolding. The results of the patient-specific finite element analysis of CAS matched well with experimental stent deployment both qualitatively and quantitatively, demonstrating the reliability of the numerical approach. The measured inter-strut angles suggested that the closed-cell design provided superior vessel scaffolding compared to the open-cell counterpart. However, the full strut interconnection of the closed-cell design reduced the stent's ability to accommodate to the irregular eccentric profile of the vessel cross section, leading to a gap between the stent surface and the vessel wall. Even though this study was limited to a single stent design and one vascular anatomy, the study confirmed the capability of dedicated computer simulations to predict differences in scaffolding by open- and closed-cell carotid artery stents. These simulations have the potential to be used in the design of novel carotid stents or for procedure planning.

Study/Experimental/Research Design: Much More Than Statistics

PubMed Central

Knight, Kenneth L.

2010-01-01

Abstract Context: The purpose of study, experimental, or research design in scientific manuscripts has changed significantly over the years. It has evolved from an explanation of the design of the experiment (ie, data gathering or acquisition) to an explanation of the statistical analysis. This practice makes “Methods” sections hard to read and understand. Objective: To clarify the difference between study design and statistical analysis, to show the advantages of a properly written study design on article comprehension, and to encourage authors to correctly describe study designs. Description: The role of study design is explored from the introduction of the concept by Fisher through modern-day scientists and the AMA Manual of Style. At one time, when experiments were simpler, the study design and statistical design were identical or very similar. With the complex research that is common today, which often includes manipulating variables to create new variables and the multiple (and different) analyses of a single data set, data collection is very different than statistical design. Thus, both a study design and a statistical design are necessary. Advantages: Scientific manuscripts will be much easier to read and comprehend. A proper experimental design serves as a road map to the study methods, helping readers to understand more clearly how the data were obtained and, therefore, assisting them in properly analyzing the results. PMID:20064054

Bibliometric Analysis of Journal of Clinical and Diagnostic Research (Dentistry Section; 2007-2014)

PubMed Central

Basavaraj, P; Singla, Ashish; Singh, Khushboo; Kundu, Hansa; Vashishtha, Vaibhav; Pandita, Venisha; Malhi, Ravneet

2015-01-01

Background: The role of scientific journals in diffusion of data concerning researches in the field of Public Health Dentistry is of premier importance. Bibliometric analysis involves analysis of publications reflecting the type of research work. Aim: The present study was conducted with an aim to determine the number and trends of published articles in Journal of Clinical and Diagnostic Research (JCDR) from Feb. 2007 to Oct.2014. Settings and Design: A retrospective observational study was conducted for JCDR. Materials and Methods: All issues of JCDR were electronically searched for the parameters : study design, area of interest of research, state /college where research was conducted, authorship pattern, source of articles published each year, changing study trends, disease under study and publication bias. Statistical Analysis used: The data was organized and analyzed using software SPSS - version 21.0; descriptive statistics was used. Results: Bibliometric analysis was done for 601 articles of JCDR published from Feb. 2007 to Oct. 2014. The total number of articles published under Dentistry section have tremendously increased from mere 2 articles in 2007 to 328 articles in 2014.Majority of the study designs published in both the journal were case reports (42.6%) followed by cross sectional studies (24.8%). 96.3% of the articles were from India. Majority of the articles published were of multi authors (65.2%) and from Educational institutes (98.4%). The trends of the articles published indicated that the case reports/series formed the major bulk (others=59.1%) followed by research studies (21.3%). Conclusion: It was concluded that most articles published were case reports followed by researches indicating an inclination towards better quality methodology. The SJR and the citation count of the articles published also indicated the quality of the scientific articles published. PMID:26023643

Design and Evaluation of Fault-Tolerant VLSI/WSI Processor Arrays.

DTIC Science & Technology

1987-12-31

studies reported in this paper. In Section .3, the reliabuility characteristics of single-level FTPA’s are discusseri. Four different type of FTPA’s are...for processor arrays are proposed and studied . Stu- dies on algorithmic and software aspects relevant to systems are reported in items 4, 5, 8, 12 and...O’Keefe M., and Fortes, J. A. B., "A Comparative Study of Two Systematic Design Methodologies for Systolic Arrays," (Long Version) International Workshop on

Estimation of unemployment rates using small area estimation model by combining time series and cross-sectional data

NASA Astrophysics Data System (ADS)

Muchlisoh, Siti; Kurnia, Anang; Notodiputro, Khairil Anwar; Mangku, I. Wayan

2016-02-01

Labor force surveys conducted over time by the rotating panel design have been carried out in many countries, including Indonesia. Labor force survey in Indonesia is regularly conducted by Statistics Indonesia (Badan Pusat Statistik-BPS) and has been known as the National Labor Force Survey (Sakernas). The main purpose of Sakernas is to obtain information about unemployment rates and its changes over time. Sakernas is a quarterly survey. The quarterly survey is designed only for estimating the parameters at the provincial level. The quarterly unemployment rate published by BPS (official statistics) is calculated based on only cross-sectional methods, despite the fact that the data is collected under rotating panel design. The study purpose to estimate a quarterly unemployment rate at the district level used small area estimation (SAE) model by combining time series and cross-sectional data. The study focused on the application and comparison between the Rao-Yu model and dynamic model in context estimating the unemployment rate based on a rotating panel survey. The goodness of fit of both models was almost similar. Both models produced an almost similar estimation and better than direct estimation, but the dynamic model was more capable than the Rao-Yu model to capture a heterogeneity across area, although it was reduced over time.

A design method for entrance sections of transonic wind tunnels with rectangular cross sections

NASA Technical Reports Server (NTRS)

Lionel, L.; Mcdevitt, J. B.

1975-01-01

A mathematical technique developed to design entrance sections for transonic or high-speed subsonic wind tunnels with rectangular cross sections is discribed. The transition from a circular cross-section setting chamber to a rectangular test section is accomplished smoothly so as not to introduce secondary flows (vortices or boundary-layer separation) into a uniform test stream. The results of static-pressure measurements in the transition region and of static and total-pressure surveys in the test section of a pilot model for a new facility at the Ames Research Center are presented.

NASA Hybrid Wing Aircraft Aeroacoustic Test Documentation Report

NASA Technical Reports Server (NTRS)

Heath, Stephanie L.; Brooks, Thomas F.; Hutcheson, Florence V.; Doty, Michael J.; Bahr, Christopher J.; Hoad, Danny; Becker, Lawrence; Humphreys, William M.; Burley, Casey L.; Stead, Dan;

Effects of eccentricities and lateral pressure on the design of stiffened compression panels

NASA Technical Reports Server (NTRS)

Giles, G. L.; Anderson, M. S.

1972-01-01

An analysis for determining the effects of eccentricities and lateral pressure on the design of stiffened compression panels is presented. The four types of panel stiffeners considered are integral, zee, integral zee, and integral tee. Mass-strength curves, which give the mass of the panel necessary to carry a specified load, are given along with related design equations needed to calculate the cross-sectional dimensions of the minimum-mass-stiffened panel. The results of the study indicate that the proportions of the panels are geometrically similar to the proportions of panels designed for no eccentricity or lateral pressure, but no cross-sectional dimensions are greater, resulting in significantly increased mass. The analytical minimum-mass designs of zee-stiffened panels are compared with designs from experimentally derived charts. An assumed eccentricity of 0.001 times the length of the panel is used to correlate the analytical and experimental data. Good correlation between the experimentally derived and the analytical curves is obtained for the range of loading where materials yield governs the design. At lower loads the mass given by the analytical curve using this assumed eccentricity is greater than that given by the experimental results.

Design of a resistive exercise device for use on the Space Shuttle

NASA Technical Reports Server (NTRS)

Carlson, Dennis L.; Durrani, Mohammed; Redilla, Christi L.

1992-01-01

The National Aeronautics and Space Administration in conjunction with the Universities Space Research Association sponsored the design of a Resistive Exercise Device (RED) for use on the Space Shuttle. The device must enable the astronauts to perform a number of exercises to prevent skeletal muscle atrophy and neuromuscular deconditioning in microgravity environments. The RED must fit the requirements for limited volume and weight and must provide a means of restraint during exercise. The design team divided the functions of the device into three major groups: methods of supplying force, methods of adjusting force, and methods of transmitting the force to the user. After analyzing the three main functions of the RED and developing alternatives for each, the design team used a comparative decision process to choose the most feasible components for the overall design. The design team selected the constant force spring alternative for further embodiment. The device consists of an array of different sized constant force springs which can be pinned in different combinations to produce the required output forces. The force is transmitted by means of a shaft and gear system. The final report is divided into four sections. An introduction section discusses the sponsor background, problem background and requirements of the device. The second section covers the alternative designs for each of the main functions. The design solution and pertinent calculations comprises the third section. The final section contains design conclusions and recommendations including topics of future work.

Tension Behaviour on the Connection of the Cold-Formed Cut-Curved Steel Channel Section

NASA Astrophysics Data System (ADS)

Sani, Mohd Syahrul Hisyam Mohd; Muftah, Fadhluhartini; Fakri Muda, Mohd; Siang Tan, Cher

2017-08-01

Cold-formed steel (CFS) are utilised as a non-structural and structural element in construction activity especially a residential house and small building roof truss system. CFS with a lot of advantages and some of disadvantages such as buckling that must be prevented for roof truss production are being studied equally. CFS was used as a top chord of the roof truss system which normally a slender section is dramatically influenced to buckling failure and instability of the structure. So, the curved section is produced for a top chord for solving the compression member of the roof truss. Besides, there are lacked of design and production information about the CFS curved channel section. In the study, the CFS is bent by using a cut-curved method because of ease of production, without the use of skilled labour and high cost machine. The tension behaviour of the strengthening method of cut-curved or could be recognised as a connection of the cut-curved section was tested and analysed. There are seven types of connection was selected. From the testing and observation, it is shown the specimen with full weld along the cut section and adds with flange element plate with two self-drilling screws (F7A) was noted to have a higher value of ultimate load. Finally, there are three alternative methods of connection for CFS cut-curved that could be a reference for a contractor and further design.

A high power, pulsed, microwave amplifier for a synthetique aperture radar electrical model. Phase 1: Design

NASA Astrophysics Data System (ADS)

Atkinson, J. E.; Barker, G. G.; Feltham, S. J.; Gabrielson, S.; Lane, P. C.; Matthews, V. J.; Perring, D.; Randall, J. P.; Saunders, J. W.; Tuck, R. A.

1982-05-01

An electrical model klystron amplifier was designed. Its features include a gridded gun, a single stage depressed collector, a rare earth permanent magnet focusing system, an input loop, six rugged tuners and a coaxial line output section incorporating a coaxial-to-waveguide transducer and a pillbox window. At each stage of the design, the thermal and mechanical aspects were investigated and optimized within the framework of the RF specification. Extensive use was made of data from the preliminary design study and from RF measurements on the breadboard model. In an additional study, a comprehensive draft tube specification has been produced. Great emphasis has been laid on a second additional study on space-qualified materials and processes.

Case-control studies in diabetes. Do they really use a case-control design?

PubMed

Ramos, Analía; Mendoza, Lilian Cristina; Rabasa, Fernanda; Bolíbar, Ignasi; Puig, Teresa; Corcoy, Rosa

2017-07-01

Studies defined as case-control do not always use this design. We aimed to estimate the frequency of mislabelled case-control studies in published articles in the area of diabetes and to identify the predictors of incorrect labelling. We searched Medline and Web of Science for articles with "diabetes" and "case control" in title and filtered for language (English/Romance) and period (January 2010-December 2014). Inclusion criteria were: (1) statement to use a case-control design in title, (2) to be a final full-length publication and (3) to have original data in the area of diabetes. Three independent reviewers went through titles, looked for full texts and reviewed them. Discrepancies were settled with a fourth reviewer. Expert epidemiologist advice was requested in case of doubt. case-control mislabelling; addressed predictors: publication year, journal impact factor and journal subject. proportion of mislabelled CC articles and assessment of predictors by multivariate logistic regression analysis. We retrieved 362 articles, 251 of them fulfilling inclusion criteria. The proportion of mislabelled CC studies was 43.8% (confidence interval 95% 37.7-50.0%). Most mislabelled studies had a cross-sectional design (82.7%). Predictors of mislabelling were publication year, journal impact factor and journal area. A relevant subset of studies defined as case-control in the area of diabetes correspond to mislabelled cross-sectional studies. Incorrect labelling misleads readers regarding the interpretation of results and the cause-effect hypothesis. Researchers, reviewers and editors should be aware of and commit to settle this issue.

A cross-sectional analysis of HIV and hepatitis C clinical trials 2007 to 2010: the relationship between industry sponsorship and randomized study design.

PubMed

Goswami, Neela D; Tsalik, Ephraim L; Naggie, Susanna; Miller, William C; Horton, John R; Pfeiffer, Christopher D; Hicks, Charles B

2014-01-22

The proportion of clinical research sponsored by industry will likely continue to expand as federal funds for academic research decreases, particularly in the fields of HIV/AIDS and hepatitis C (HCV). While HIV and HCV continue to burden the US population, insufficient data exists as to how industry sponsorship affects clinical trials involving these infectious diseases. Debate exists about whether pharmaceutical companies undertake more market-driven research practices to promote therapeutics, or instead conduct more rigorous trials than their non-industry counterparts because of increased resources and scrutiny. The ClinicalTrials.gov registry, which allows investigators to fulfill a federal mandate for public trial registration, provides an opportunity for critical evaluation of study designs for industry-sponsored trials, independent of publication status. As part of a large public policy effort, the Clinical Trials Transformation Initiative (CTTI) recently transformed the ClinicalTrials.gov registry into a searchable dataset to facilitate research on clinical trials themselves. We conducted a cross-sectional analysis of 477 HIV and HCV drug treatment trials, registered with ClinicalTrials.gov from 1 October 2007 to 27 September 2010, to study the relationship of study sponsorship with randomized study design. The likelihood of using randomization given industry (versus non-industry) sponsorship was reported with prevalence ratios (PR). PRs were estimated using crude and stratified tabular analysis and Poisson regression adjusting for presence of a data monitoring committee, enrollment size, study phase, number of study sites, inclusion of foreign study sites, exclusion of persons older than age 65, and disease condition. The crude PR was 1.17 (95% CI 0.94, 1.45). Adjusted Poisson models produced a PR of 1.13 (95% CI 0.82, 1.56). There was a trend toward mild effect measure modification by study phase, but this was not statistically significant. In stratified tabular analysis the adjusted PR was 1.14 (95% CI 0.78, 1.68) among phase 2/3 trials and 1.06 (95% CI 0.50, 2.22) among phase 4 trials. No significant relationship was found between industry sponsorship and use of randomization in trial design in this cross-sectional study. Prospective studies evaluating other aspects of trial design may shed further light on the relationship between industry sponsorship and appropriate trial methodology.

A cross-sectional analysis of HIV and hepatitis C clinical trials 2007 to 2010: the relationship between industry sponsorship and randomized study design

PubMed Central

2014-01-01

Background The proportion of clinical research sponsored by industry will likely continue to expand as federal funds for academic research decreases, particularly in the fields of HIV/AIDS and hepatitis C (HCV). While HIV and HCV continue to burden the US population, insufficient data exists as to how industry sponsorship affects clinical trials involving these infectious diseases. Debate exists about whether pharmaceutical companies undertake more market-driven research practices to promote therapeutics, or instead conduct more rigorous trials than their non-industry counterparts because of increased resources and scrutiny. The ClinicalTrials.gov registry, which allows investigators to fulfill a federal mandate for public trial registration, provides an opportunity for critical evaluation of study designs for industry-sponsored trials, independent of publication status. As part of a large public policy effort, the Clinical Trials Transformation Initiative (CTTI) recently transformed the ClinicalTrials.gov registry into a searchable dataset to facilitate research on clinical trials themselves. Methods We conducted a cross-sectional analysis of 477 HIV and HCV drug treatment trials, registered with ClinicalTrials.gov from 1 October 2007 to 27 September 2010, to study the relationship of study sponsorship with randomized study design. The likelihood of using randomization given industry (versus non-industry) sponsorship was reported with prevalence ratios (PR). PRs were estimated using crude and stratified tabular analysis and Poisson regression adjusting for presence of a data monitoring committee, enrollment size, study phase, number of study sites, inclusion of foreign study sites, exclusion of persons older than age 65, and disease condition. Results The crude PR was 1.17 (95% CI 0.94, 1.45). Adjusted Poisson models produced a PR of 1.13 (95% CI 0.82, 1.56). There was a trend toward mild effect measure modification by study phase, but this was not statistically significant. In stratified tabular analysis the adjusted PR was 1.14 (95% CI 0.78, 1.68) among phase 2/3 trials and 1.06 (95% CI 0.50, 2.22) among phase 4 trials. Conclusions No significant relationship was found between industry sponsorship and use of randomization in trial design in this cross-sectional study. Prospective studies evaluating other aspects of trial design may shed further light on the relationship between industry sponsorship and appropriate trial methodology. PMID:24450313

National Longitudinal Study of the High School Class of 1972: A Summary of the Merged Findings from Analyses by RTI of the First Follow-Up and Preceding Data. RTI Concept Paper No. CP-22-75-07.

ERIC Educational Resources Information Center

Research Triangle Inst., Durham, NC. Center for Educational Research and Evaluation.

An overview of the National Longitudinal Study of the High School Class of 1972 (NLS) is provided. Section one describes the research design for the base-year and first through third followup surveys. Section two summarizes findings from data analyses of the first followup and base-year, completed before September 1975. The findings are presented…

Breakthroughs in Low Profile Leaky Wave HPM Antennas

DTIC Science & Technology

2016-10-17

3D RF modeling, but the design time and effort will be greatly reduced compared to starting from scratch. The LWAs featured here exhibit beam...Section 4 present related and novel antenna designs that leverage some of the concepts from this research program. Section 5 and Section 6 present...parameters that we used previously for the wire-grill design in Figure 3, but this time with the intent to combine it with an acrylic (εr=2.55) window of

47 CFR 22.223 - Designated entities.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 47 Telecommunication 2 2010-10-01 2010-10-01 false Designated entities. 22.223 Section 22.223... Licensing Requirements and Procedures Competitive Bidding Procedures § 22.223 Designated entities. (a) Scope... sections. (b) A small business is an entity that either: (1) Together with its affiliates and controlling...

47 CFR 22.223 - Designated entities.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 47 Telecommunication 2 2011-10-01 2011-10-01 false Designated entities. 22.223 Section 22.223... Licensing Requirements and Procedures Competitive Bidding Procedures § 22.223 Designated entities. (a) Scope... sections. (b) A small business is an entity that either: (1) Together with its affiliates and controlling...

47 CFR 17.9 - Designated antenna farm areas.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 47 Telecommunication 1 2011-10-01 2011-10-01 false Designated antenna farm areas. 17.9 Section 17... ANTENNA STRUCTURES Federal Aviation Administration Notification Criteria § 17.9 Designated antenna farm areas. The areas described in the following paragraphs of this section are established as antenna farm...

47 CFR 17.9 - Designated antenna farm areas.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 47 Telecommunication 1 2010-10-01 2010-10-01 false Designated antenna farm areas. 17.9 Section 17... ANTENNA STRUCTURES Federal Aviation Administration Notification Criteria § 17.9 Designated antenna farm areas. The areas described in the following paragraphs of this section are established as antenna farm...

47 CFR 17.9 - Designated antenna farm areas.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 47 Telecommunication 1 2013-10-01 2013-10-01 false Designated antenna farm areas. 17.9 Section 17... ANTENNA STRUCTURES Federal Aviation Administration Notification Criteria § 17.9 Designated antenna farm areas. The areas described in the following paragraphs of this section are established as antenna farm...

47 CFR 17.9 - Designated antenna farm areas.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 47 Telecommunication 1 2012-10-01 2012-10-01 false Designated antenna farm areas. 17.9 Section 17... ANTENNA STRUCTURES Federal Aviation Administration Notification Criteria § 17.9 Designated antenna farm areas. The areas described in the following paragraphs of this section are established as antenna farm...

47 CFR 17.9 - Designated antenna farm areas.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 47 Telecommunication 1 2014-10-01 2014-10-01 false Designated antenna farm areas. 17.9 Section 17... ANTENNA STRUCTURES Federal Aviation Administration Notification Criteria § 17.9 Designated antenna farm areas. The areas described in the following paragraphs of this section are established as antenna farm...

47 CFR 54.202 - Additional requirements for Commission designation of eligible telecommunications carriers.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 47 Telecommunication 3 2014-10-01 2014-10-01 false Additional requirements for Commission designation of eligible telecommunications carriers. 54.202 Section 54.202 Telecommunication FEDERAL... telecommunications carriers. (a) In order to be designated an eligible telecommunications carrier under section 214(e...

47 CFR 54.202 - Additional requirements for Commission designation of eligible telecommunications carriers.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 47 Telecommunication 3 2012-10-01 2012-10-01 false Additional requirements for Commission designation of eligible telecommunications carriers. 54.202 Section 54.202 Telecommunication FEDERAL... telecommunications carriers. (a) In order to be designated an eligible telecommunications carrier under section 214(e...

47 CFR 54.202 - Additional requirements for Commission designation of eligible telecommunications carriers.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 47 Telecommunication 3 2013-10-01 2013-10-01 false Additional requirements for Commission designation of eligible telecommunications carriers. 54.202 Section 54.202 Telecommunication FEDERAL... telecommunications carriers. (a) In order to be designated an eligible telecommunications carrier under section 214(e...

Development of a general method for obtaining the geometry of microfluidic networks

DOE Office of Scientific and Technical Information (OSTI.GOV)

Razavi, Mohammad Sayed, E-mail: m.sayedrazavi@gmail.com; Salimpour, M. R.; Shirani, Ebrahim

2014-01-15

In the present study, a general method for geometry of fluidic networks is developed with emphasis on pressure-driven flows in the microfluidic applications. The design method is based on general features of network's geometry such as cross-sectional area and length of channels. Also, the method is applicable to various cross-sectional shapes such as circular, rectangular, triangular, and trapezoidal cross sections. Using constructal theory, the flow resistance, energy loss and performance of the network are optimized. Also, by this method, practical design strategies for the fabrication of microfluidic networks can be improved. The design method enables rapid prediction of fluid flowmore » in the complex network of channels and is very useful for improving proper miniaturization and integration of microfluidic networks. Minimization of flow resistance of the network of channels leads to universal constants for consecutive cross-sectional areas and lengths. For a Y-shaped network, the optimal ratios of consecutive cross-section areas (A{sub i+1}/A{sub i}) and lengths (L{sub i+1}/L{sub i}) are obtained as A{sub i+1}/A{sub i} = 2{sup −2/3} and L{sub i+1}/L{sub i} = 2{sup −1/3}, respectively. It is shown that energy loss in the network is proportional to the volume of network. It is also seen when the number of channels is increased both the hydraulic resistance and the volume occupied by the network are increased in a similar manner. Furthermore, the method offers that fabrication of multi-depth and multi-width microchannels should be considered as an integral part of designing procedures. Finally, numerical simulations for the fluid flow in the network have been performed and results show very good agreement with analytic results.« less

Impacts of Noise Barriers on Near-Road Air Quality

EPA Science Inventory

Numerous health studies show an increase in adverse health effects for populations near large roadways. A study was designed to assess traffic emission impacts on air quality near a heavily traveled highway. The portion of highway studied included a section of open field and a se...

School Location, School Section and Students' Gender as Predictors to Secondary School Dropout Rate in Rivers State, Nigeria

ERIC Educational Resources Information Center

Christian, Mathew

2015-01-01

This study was undertaken to underscore the extent the variables of school location, students' gender and school section can predict the rate of drop out of secondary school students. Ex post facto design was adopted and all data on students' enrollment, retention and completion were collected from available schools' records for two cohorts of…

Cross-Sectional and Longitudinal Risk Factors for Falls, Fear of Falling, and Falls Efficacy in a Cohort of Middle-Aged African Americans

ERIC Educational Resources Information Center

Anderson, Elena M.; Wolinsky, Fredric D.; Miller, J. Phillip; Wilson, Margaret-Mary G.; Malmstrom, Theodore K.; Miller, Douglas K.

2006-01-01

Purpose: The purpose of this study is to cross-sectionally and longitudinally identify risk factors for falls, fear of falling, and falls efficacy in late-middle-aged African Americans. Design and Methods: We performed in-home assessments on a probability sample of 998 African Americans and conducted two annual follow-up interviews. Multiple…

Career Ladders and Teacher Incentives: The Utah Experiment. Part I: The Implementation. Final Report: Secretary's Discretionary Program Implementation Grant to Develop Teacher Incentive Structures.

ERIC Educational Resources Information Center

Peterson, Ken; Kauchak, Don

This volume, the first of two reports on development of teacher incentive structures, focuses on implementation of a career ladder design and teacher evaluation experiment in four Utah school districts. The report has five sections. Section 1 describes study background and implementation of an evaluation-reward system that featured data collection…

Selected Essays and Curriculum Units: Foreign Language Instruction through the Study of Literary Texts. French, German, Spanish.

ERIC Educational Resources Information Center

Silber, Ellen S., Ed.; Krug, Clara, Ed.

This guide presents essays and curriculum units designed for use by secondary and college teachers of French, German, and Spanish as a foreign language. The first section of the work includes two essays, in French, and eight curriculum units based on the stories of Guy de Maupassant. The second section contains seven curriculum units that…

Continuation of superpave projects monitoring.

DOT National Transportation Integrated Search

2011-07-01

This study involved the continuous monitoring of material properties and field performance of : twelve Superpave project sections in Florida for the establishment of reasonable and effective mixture : design guidelines and criteria, the identificatio...

Volume II: Ecosystem management: principles and applications.

Treesearch

M.E. Jensen; P.S. Bourgeron

1994-01-01

This document provides land managers with practical suggestions for implementing ecosystem management. It contains 28 papers organized into five sections: historical perspectives, ecological principles, sampling design, case studies, and implementation strategies.

Systems design study of the Pioneer Venus spacecraft. Appendices to volume 1, sections 3-6 (part 1 of 3). [design of Venus probe windows

NASA Technical Reports Server (NTRS)

1973-01-01

The design is described of the Venus probe windows, which are required to measure solar flux, infrared flux, aureole, and cloud particles. Window heating and structural materials for the probe window assemblies are discussed along with the magnetometer. The command lists for science, power and communication requirements, telemetry sign characteristics, mission profile summary, mass properties of payloads, and failure modes are presented.

Computer-Aided Design Applications for the Base Civil Engineering Technical Design Section.

DTIC Science & Technology

1983-09-01

4 1983.’ S DEPARTMENT OF TiHE AIR FORCE L ~j AIR UNIVERSITY * AIR FORCE INSTITUTE OF TECHNOLOGY Nam Wright- Patterson Air Force Bas, Ohio d ’rI ’ 4to...I -. L I 1it it COMPUTER-AIDED DESIGN APPLICATIONS FOR THE BASE CIVIL ENGINEERING TECHNICAL DESIGN SECTION William M. Duncan, Captain, USAF LSSR 15-83...8217 .. ’ , .. - -. . ’ . , ._, - . . - .2 , _ : ’i 1 . . . . .- J.. .. . ’ _ -i l - , . analysis and design, water supply and wastewater disposal system design, and most

In the eye of the beholder: Evaluative context modulates mind-wandering.

PubMed

Forrin, Noah D; Risko, Evan F; Smilek, Daniel

2018-04-01

We present novel evidence that mind-wandering rates during a reading task are influenced by experimental context. In Experiment 1, participants read a series of passages and we measured their frequency of mind-wandering and their subjective evaluations of passage difficulty/interest. Section length was manipulated, such that some passages were presented in short sections and others were presented in long sections. Importantly, participants were randomly assigned to complete either a within-subject version of the experiment (in which they read some short-section passages and some long-section passages) or a between-subjects design (in which they only read either short-section or long-section passages). We found that the within-subject design yielded significant effects of section length on mind-wandering and on subjective passage evaluations, whereas the between-subjects design yielded null effects. This pattern of results was replicated in Experiment 2. These results provide compelling evidence that mind-wandering rates can be influenced by the experimental design. We conclude that mind-wandering is not only driven by the objective demands of the task, but also by subjective evaluations of those task properties, which are influenced by the context in which the task is evaluated (i.e., the "evaluative context"). Copyright © 2018. Published by Elsevier B.V.

High-Tip-Speed, Low-Loading Transonic Fan Stage. Part 1: Aerodynamic and Mechanical Design

NASA Technical Reports Server (NTRS)

Wright, L. C.; Vitale, N. G.; Ware, T. C.; Erwin, J. R.

1973-01-01

A high-tip-speed, low-loading transonic fan stage was designed to deliver an overall pressure ratio of 1.5 with an adiabatic efficiency of 86 percent. The design flow per unit annulus area is 42.0 pounds per square foot. The fan features a hub/tip ratio of 0.46, a tip diameter of 28.74 in. and operates at a design tip speed of 1600 fps. For these design conditions, the rotor blade tip region operates with supersonic inlet and supersonic discharge relative velocities. A sophisticated quasi-three-dimensional characteristic section design procedure was used for the all-supersonic sections and the inlet of the midspan transonic sections. For regions where the relative outlet velocities are supersonic, the blade operates with weak oblique shocks only.

Flow Distribution Control Characteristics in Marine Gas Turbine Waste- Heat Recovery Systems. Phase 2. Flow Distribution Control in Waste-Heat Steam Generators

DTIC Science & Technology

1982-07-01

waste-heat steam generators. The applicable steam generator design concepts and general design consideration were reviewed and critical problems...a once-through forced-circulation steam generator design should be selected because of stability, reliability, compact- ness and lightweight...consists of three sections and one appendix. In Section I, the applicable steam generator design conccpts and general design * considerations are reviewed

Study designs, use of statistical tests, and statistical analysis software choice in 2015: Results from two Pakistani monthly Medline indexed journals.

PubMed

Shaikh, Masood Ali

2017-09-01

Assessment of research articles in terms of study designs used, statistical tests applied and the use of statistical analysis programmes help determine research activity profile and trends in the country. In this descriptive study, all original articles published by Journal of Pakistan Medical Association (JPMA) and Journal of the College of Physicians and Surgeons Pakistan (JCPSP), in the year 2015 were reviewed in terms of study designs used, application of statistical tests, and the use of statistical analysis programmes. JPMA and JCPSP published 192 and 128 original articles, respectively, in the year 2015. Results of this study indicate that cross-sectional study design, bivariate inferential statistical analysis entailing comparison between two variables/groups, and use of statistical software programme SPSS to be the most common study design, inferential statistical analysis, and statistical analysis software programmes, respectively. These results echo previously published assessment of these two journals for the year 2014.

Mindfulness Mechanisms in Sports: Mediating Effects of Rumination and Emotion Regulation on Sport-Specific Coping.

PubMed

Josefsson, Torbjörn; Ivarsson, Andreas; Lindwall, Magnus; Gustafsson, Henrik; Stenling, Andreas; Böröy, Jan; Mattsson, Emil; Carnebratt, Jakob; Sevholt, Simon; Falkevik, Emil

2017-01-01

The main objective of the project was to examine a proposed theoretical model of mindfulness mechanisms in sports. We conducted two studies (the first study using a cross-sectional design and the second a longitudinal design) to investigate if rumination and emotion regulation mediate the relation between dispositional mindfulness and sport-specific coping. Two hundred and forty-two young elite athletes, drawn from various sports, were recruited for the cross-sectional study. For the longitudinal study, 65 elite athletes were recruited. All analyses were performed using Bayesian statistics. The path analyses showed credible indirect effects of dispositional mindfulness on coping via rumination and emotion regulation in both the cross-sectional study and the longitudinal study. Additionally, the results in both studies showed credible direct effects of dispositional mindfulness on rumination and emotion regulation. Further, credible direct effects of emotion regulation as well as rumination on coping were also found in both studies. Our findings support the theoretical model, indicating that rumination and emotion regulation function as essential mechanisms in the relation between dispositional mindfulness and sport-specific coping skills. Increased dispositional mindfulness in competitive athletes (i.e. by practicing mindfulness) may lead to reductions in rumination, as well as an improved capacity to regulate negative emotions. By doing so, athletes may improve their sport-related coping skills, and thereby enhance athletic performance.

40 CFR 81.305 - California.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 17 2011-07-01 2011-07-01 false California. 81.305 Section 81.305 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) DESIGNATION OF AREAS FOR AIR QUALITY PLANNING PURPOSES Section 107 Attainment Status Designations § 81.305 California. California—TSP Designated area Does not...

40 CFR 81.305 - California.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 18 2012-07-01 2012-07-01 false California. 81.305 Section 81.305 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) DESIGNATION OF AREAS FOR AIR QUALITY PLANNING PURPOSES Section 107 Attainment Status Designations § 81.305 California. California—TSP Designated area Does not...

40 CFR 81.305 - California.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 18 2014-07-01 2014-07-01 false California. 81.305 Section 81.305 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) DESIGNATION OF AREAS FOR AIR QUALITY PLANNING PURPOSES Section 107 Attainment Status Designations § 81.305 California. California—TSP Designated area Does not...

29 CFR 2570.133 - Parties, how designated.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 29 Labor 9 2011-07-01 2011-07-01 false Parties, how designated. 2570.133 Section 2570.133 Labor Regulations Relating to Labor (Continued) EMPLOYEE BENEFITS SECURITY ADMINISTRATION, DEPARTMENT OF LABOR... ERISA Section 502(c)(7) § 2570.133 Parties, how designated. For 502(c)(7) civil penalty proceedings...

29 CFR 2570.133 - Parties, how designated.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 29 Labor 9 2010-07-01 2010-07-01 false Parties, how designated. 2570.133 Section 2570.133 Labor Regulations Relating to Labor (Continued) EMPLOYEE BENEFITS SECURITY ADMINISTRATION, DEPARTMENT OF LABOR... ERISA Section 502(c)(7) § 2570.133 Parties, how designated. For 502(c)(7) civil penalty proceedings...

29 CFR 2570.133 - Parties, how designated.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 29 Labor 9 2012-07-01 2012-07-01 false Parties, how designated. 2570.133 Section 2570.133 Labor Regulations Relating to Labor (Continued) EMPLOYEE BENEFITS SECURITY ADMINISTRATION, DEPARTMENT OF LABOR... ERISA Section 502(c)(7) § 2570.133 Parties, how designated. For 502(c)(7) civil penalty proceedings...

Analysis of thick brain sections by obverse-reverse computer microscopy: application of a new, high clarity Golgi-Nissl stain.

PubMed

Glaser, E M; Van der Loos, H

1981-08-01

Exceptionally clear Golgi-Nissl sections of 300 micron thickness have been morphometrically studied by light microscopy using oil immersion objectives. The clarity results from a new variation of a staining procedure that combines Golgi and Nissl images in one section. A viewing technique has been developed that permits a histologic preparation to be examined from its obverse (or normally viewed) side and its reverse (or under) side. The technique was designed for use with a computer microscope but can be employed with any light microscope whose stage position can be measured within 100 micron. Sections thicker than 300 micron can be studied dependent on the working distance of the objective lens, provided that the clarity of the material permits it.

17 CFR 230.421 - Presentation of information in prospectuses.

Code of Federal Regulations, 2010 CFR

2010-04-01

... in such fashion as to obscure any of the required information or any information necessary to keep... organization, language, and design of the front and back cover pages, the summary, and the risk factors section.... (3) In designing these sections or other sections of the prospectus, you may include pictures, logos...

17 CFR 230.421 - Presentation of information in prospectuses.

Code of Federal Regulations, 2011 CFR

2011-04-01

... in such fashion as to obscure any of the required information or any information necessary to keep... organization, language, and design of the front and back cover pages, the summary, and the risk factors section.... (3) In designing these sections or other sections of the prospectus, you may include pictures, logos...

A meta-analysis on progressive atrophy in intractable temporal lobe epilepsy

PubMed Central

Caciagli, Lorenzo; Bernasconi, Andrea; Wiebe, Samuel; Koepp, Matthias J.; Bernasconi, Neda

2017-01-01

Objective: It remains unclear whether drug-resistant temporal lobe epilepsy (TLE) is associated with cumulative brain damage, with no expert consensus and no quantitative syntheses of the available evidence. Methods: We conducted a systematic review and meta-analysis of MRI studies on progressive atrophy, searching PubMed and Ovid MEDLINE databases for cross-sectional and longitudinal quantitative MRI studies on drug-resistant TLE. Results: We screened 2,976 records and assessed eligibility of 248 full-text articles. Forty-two articles met the inclusion criteria for quantitative evaluation. We observed a predominance of cross-sectional studies, use of different clinical indices of progression, and high heterogeneity in age-control procedures. Meta-analysis of 18/1 cross-sectional/longitudinal studies on hippocampal atrophy (n = 979 patients) yielded a pooled effect size of r = −0.42 for ipsilateral atrophy related to epilepsy duration (95% confidence interval [CI] −0.51 to −0.32; p < 0.0001; I2 = 65.22%) and r = −0.35 related to seizure frequency (95% CI −0.47 to −0.22; p < 0.0001; I2 = 61.97%). Sensitivity analyses did not change the results. Narrative synthesis of 25/3 cross-sectional/longitudinal studies on whole brain atrophy (n = 1,504 patients) indicated that >80% of articles reported duration-related progression in extratemporal cortical and subcortical regions. Detailed analysis of study design features yielded low to moderate levels of evidence for progressive atrophy across studies, mainly due to dominance of cross-sectional over longitudinal investigations, use of diverse measures of seizure estimates, and absence of consistent age control procedures. Conclusions: While the neuroimaging literature is overall suggestive of progressive atrophy in drug-resistant TLE, published studies have employed rather weak designs to directly demonstrate it. Longitudinal multicohort studies are needed to unequivocally differentiate aging from disease progression. PMID:28687722

Viscous Design of TCA Configuration

NASA Technical Reports Server (NTRS)

Krist, Steven E.; Bauer, Steven X. S.; Campbell, Richard L.

1999-01-01

The goal in this effort is to redesign the baseline TCA configuration for improved performance at both supersonic and transonic cruise. Viscous analyses are conducted with OVERFLOW, a Navier-Stokes code for overset grids, using PEGSUS to compute the interpolations between overset grids. Viscous designs are conducted with OVERDISC, a script which couples OVERFLOW with the Constrained Direct Iterative Surface Curvature (CDISC) inverse design method. The successful execution of any computational fluid dynamics (CFD) based aerodynamic design method for complex configurations requires an efficient method for regenerating the computational grids to account for modifications to the configuration shape. The first section of this presentation deals with the automated regridding procedure used to generate overset grids for the fuselage/wing/diverter/nacelle configurations analysed in this effort. The second section outlines the procedures utilized to conduct OVERDISC inverse designs. The third section briefly covers the work conducted by Dick Campbell, in which a dual-point design at Mach 2.4 and 0.9 was attempted using OVERDISC; the initial configuration from which this design effort was started is an early version of the optimized shape for the TCA configuration developed by the Boeing Commercial Airplane Group (BCAG), which eventually evolved into the NCV design. The final section presents results from application of the Natural Flow Wing design philosophy to the TCA configuration.

21 CFR 201.57 - Specific requirements on content and format of labeling for human prescription drug and...

Code of Federal Regulations, 2013 CFR

2013-04-01

... comparative rates of occurrence cannot be reliably determined (e.g., adverse reactions were observed only in... in vivo study designs or results (e.g., drug interaction studies), may be included in this section if...

21 CFR 201.57 - Specific requirements on content and format of labeling for human prescription drug and...

Code of Federal Regulations, 2012 CFR

2012-04-01

... comparative rates of occurrence cannot be reliably determined (e.g., adverse reactions were observed only in... in vivo study designs or results (e.g., drug interaction studies), may be included in this section if...

21 CFR 201.57 - Specific requirements on content and format of labeling for human prescription drug and...

Code of Federal Regulations, 2014 CFR

2014-04-01

... comparative rates of occurrence cannot be reliably determined (e.g., adverse reactions were observed only in... in vivo study designs or results (e.g., drug interaction studies), may be included in this section if...

NHEXAS PHASE I MARYLAND STUDY--QUALITY SYSTEMS AND IMPLEMENTATION PLAN (HSPH QSIP)

EPA Science Inventory

This document describes the project design and quality systems used by the Maryland Study for NHEXAS Phase 1. It contains the following sections: Project Planning and Organization, Project Implementation Plan, Data Acquisition and Management, Records Usage and Management, Routin...

Project Themis: Water Visualization Study

DTIC Science & Technology

2011-09-15

parameters and design space. Apparatus is discussed, including water flow loop and test section parts, as well as flow measurements, LDV, PLIF, and...release; distribution unlimited Project Themis: Water Visualization Study Allen Bishop AFRL/RZSE 15 Sept 2011 2 About Me • BS & MS Aerospace

Simulations & Case Studies. [SITE 2002 Section].

ERIC Educational Resources Information Center

Seymour, Cathy R., Ed.

This document contains the following papers on simulations and case studies from the SITE (Society for Information Technology & Teacher Education) 2002 conference: "3-D Virtual Classroom Technology" (Kimberly Arseneau Miller, Angela Glod); "Simulated Lesson Design Studios" (Willis Copeland); "Lights, Camera, Integration: Presentation Programs and…

Redesigned rotor for a highly loaded, 1800 ft/sec tip speed compressor fan stage 1: Aerodynamic and mechanical design

NASA Technical Reports Server (NTRS)

Halle, J. E.; Ruschak, J. T.

1975-01-01

A highly loaded, high tip-speed fan rotor was designed with multiple-circular-arc airfoil sections as a replacement for a marginally successful rotor which had precompression airfoil sections. The substitution of airfoil sections was the only aerodynamic change. Structural design of the redesigned rotor blade was guided by successful experience with the original blade. Calculated stress levels and stability parameters for the redesigned rotor are within limits demonstrated in tests of the original rotor.

Continuation of superpave projects monitoring.

DOT National Transportation Integrated Search

2011-07-01

This study involved the continuous monitoring of material properties and field performance of twelve Superpave project sections in Florida for the establishment of reasonable and effective mixture design guidelines and criteria, the identification an...

49 CFR 511.64 - Petitions for settlement; timing, contents.

Code of Federal Regulations, 2011 CFR

2011-10-01

... section proposing conditions for settlement. Conditions for settlement can be specific acts designed to... technology development programs, or making public the results of privately performed studies, surveys, or research activities. ...

49 CFR 511.64 - Petitions for settlement; timing, contents.

Code of Federal Regulations, 2012 CFR

2012-10-01

... section proposing conditions for settlement. Conditions for settlement can be specific acts designed to... technology development programs, or making public the results of privately performed studies, surveys, or research activities. ...

49 CFR 511.64 - Petitions for settlement; timing, contents.

Code of Federal Regulations, 2013 CFR

2013-10-01

... section proposing conditions for settlement. Conditions for settlement can be specific acts designed to... technology development programs, or making public the results of privately performed studies, surveys, or research activities. ...

49 CFR 511.64 - Petitions for settlement; timing, contents.

Code of Federal Regulations, 2010 CFR

2010-10-01

... section proposing conditions for settlement. Conditions for settlement can be specific acts designed to... technology development programs, or making public the results of privately performed studies, surveys, or research activities. ...

49 CFR 511.64 - Petitions for settlement; timing, contents.

Code of Federal Regulations, 2014 CFR

2014-10-01

... section proposing conditions for settlement. Conditions for settlement can be specific acts designed to... technology development programs, or making public the results of privately performed studies, surveys, or research activities. ...

Predicting Parental Monitoring Behaviours for Sugar-Sweetened Beverages in Parents of School-Aged Children: An Application of the Integrative Behavioural Model

ERIC Educational Resources Information Center

Housely, Alexandra; Branscum, Paul; Cheney, Marshall; Hofford, Craig

2016-01-01

Objective: The objective of this study was to identify theory-based psychosocial and environmental determinants of parental monitoring practices related to child sugar-sweetened beverage consumption. Design: Cross-sectional design. Method: Data were obtained from a convenience sample of parents (n = 270) with children attending an after-school…

Wide area detection system: Conceptual design study. [using television and microelectronic technology

NASA Technical Reports Server (NTRS)

Hilbert, E. E.; Carl, C.; Goss, W.; Hansen, G. R.; Olsasky, M. J.; Johnston, A. R.

1978-01-01

An integrated sensor for traffic surveillance on mainline sections of urban freeways is described. Applicable imaging and processor technology is surveyed and the functional requirements for the sensors and the conceptual design of the breadboard sensors are given. Parameters measured by the sensors include lane density, speed, and volume. The freeway image is also used for incident diagnosis.

Mediating Effects of Coping, Personal Belief, and Social Support on the Relationship among Stress, Depression, and Smoking Behaviour in University Students

ERIC Educational Resources Information Center

Sun, Jing; Buys, Nicholas; Stewart, Donald; Shum, David

2011-01-01

Purpose: The purpose of this paper is to investigate whether university students' smoking behaviour is associated with higher levels of stress and depression directly, or indirectly, via the mediation of coping, personal beliefs and social support. Design/methodology/approach: The study design involves a cross-sectional survey. Structural equation…

Complexity and Chaos - State-of-the-Art; Formulations and Measures of Complexity

DTIC Science & Technology

2007-09-01

Systems (SoS) Section. His research interests are oriented toward the study, design and engineering of military complex systems through the lens of the...Approved for release by This work is part of project 15bp01 – Defensive Software Design . © Her Majesty the Queen in Right of Canada...16 2.35 Minimum Number of Sub Groups

Passive mode-locking of 3.25μm GaSb-based type-I quantum-well cascade diode lasers

NASA Astrophysics Data System (ADS)

Feng, Tao; Shterengas, Leon; Kipshidze, Gela; Hosoda, Takashi; Wang, Meng; Belenky, Gregory

2018-02-01

Passively mode-locked type-I quantum well cascade diode lasers emitting in the methane absorption band near 3.25 μm were designed, fabricated and characterized. The deep etched 5.5-μm-wide single spatial mode ridge waveguide design utilizing split-contact architecture was implemented. The devices with absorber to gain section length ratios of 11% and 5.5% were studied. Lasers with the longer absorber section ( 300 μm) generated smooth bell-shape-like emission spectrum with about 30 lasing modes at full-width-at-half-maximum level. Devices with reverse biased absorber section demonstrated stable radio frequency beat with nearly perfect Lorentzian shape over four orders of magnitude of intensity. The estimated pulse-to-pulse timing jitter was about 110 fs/cycle. Laser generated average power of more than 1 mW in mode-locked regime.

Imaging and elemental mapping of biological specimens with a dual-EDS dedicated scanning transmission electron microscope

PubMed Central

Wu, J.S.; Kim, A. M.; Bleher, R.; Myers, B.D.; Marvin, R. G.; Inada, H.; Nakamura, K.; Zhang, X.F.; Roth, E.; Li, S.Y.; Woodruff, T. K.; O'Halloran, T. V.; Dravid, Vinayak P.

2013-01-01

A dedicated analytical scanning transmission electron microscope (STEM) with dual energy dispersive spectroscopy (EDS) detectors has been designed for complementary high performance imaging as well as high sensitivity elemental analysis and mapping of biological structures. The performance of this new design, based on a Hitachi HD-2300A model, was evaluated using a variety of biological specimens. With three imaging detectors, both the surface and internal structure of cells can be examined simultaneously. The whole-cell elemental mapping, especially of heavier metal species that have low cross-section for electron energy loss spectroscopy (EELS), can be faithfully obtained. Optimization of STEM imaging conditions is applied to thick sections as well as thin sections of biological cells under low-dose conditions at room- and cryogenic temperatures. Such multimodal capabilities applied to soft/biological structures usher a new era for analytical studies in biological systems. PMID:23500508

Simplified, inverse, ejector design tool

NASA Technical Reports Server (NTRS)

Dechant, Lawrence J.

1993-01-01

A simple lumped parameter based inverse design tool has been developed which provides flow path geometry and entrainment estimates subject to operational, acoustic, and design constraints. These constraints are manifested through specification of primary mass flow rate or ejector thrust, fully-mixed exit velocity, and static pressure matching. Fundamentally, integral forms of the conservation equations coupled with the specified design constraints are combined to yield an easily invertible linear system in terms of the flow path cross-sectional areas. Entrainment is computed by back substitution. Initial comparison with experimental and analogous one-dimensional methods show good agreement. Thus, this simple inverse design code provides an analytically based, preliminary design tool with direct application to High Speed Civil Transport (HSCT) design studies.

Velocity-based analysis of sediment incipient deposition in rigid boundary open channels.

PubMed

Aksoy, Hafzullah; Safari, Mir Jafar Sadegh; Unal, Necati Erdem; Mohammadi, Mirali

2017-11-01

Drainage systems must be designed in a way to minimize undesired problems such as decrease in hydraulic capacity of the channel, blockage and transport of pollutants due to deposition of sediment. Channel design considering self-cleansing criteria are used to solve the sedimentation problem. Incipient deposition is one of the non-deposition self-cleansing design criteria that can be used as a conservative method for channel design. Experimental studies have been carried out in five different cross-section channels, namely trapezoidal, rectangular, circular, U-shape and V-bottom. Experiments were performed in a tilting flume using four different sizes of sands as sediment in nine different channel bed slopes. Two well-known methods, namely the Novak & Nalluri and Yang methods are considered for the analysis of sediment motion. Equations developed using experimental data are found to be in agreement with the literature. It is concluded that the design velocity depends on the shape of the channel cross-section. Rectangular and V-bottom channels need lower and higher incipient deposition velocities, respectively, in comparison with other channels.

Tourism Studies. Guide to Standards and Implementation. Career & Technology Studies.

ERIC Educational Resources Information Center

Alberta Dept. of Education, Edmonton. Curriculum Standards Branch.

This Alberta curriculum guide, focusing on tourism studies, defines competencies that: help students build daily living skills, investigate career options in the design and repair of motor vehicles, use technology in these fields effectively and efficiently, and prepare for entry into the workplace or related postsecondary programs. Section A…

Distance Learning Library Services in Ugandan Universities

ERIC Educational Resources Information Center

Mayende, Jackline Estomihi Kiwelu; Obura, Constant Okello

2013-01-01

The study carried out at Makerere University and Uganda Martyrs University in 2010 aimed at providing strategies for enhanced distance learning library services in terms of convenience and adequacy. The study adopted a cross sectional descriptive survey design. The study revealed services provided in branch libraries in Ugandan universities were…

Design and implementation of a cross-sectional nutritional phenotyping study of healthy US adults

USDA-ARS?s Scientific Manuscript database

Metabolic imbalance is a key determinant of risk of chronic diseases. Metabolic health cannot be assessed solely by body mass calculations or by static, fasted state biochemical readouts. Although previous studies have described temporal responses to dietary challenges, these studies fail to assess ...

Performance evaluation of Arizona's LTPP SPS-9 Project : strategic study of flexible pavement mix design factors.

DOT National Transportation Integrated Search

2016-01-01

As part of the Long Term Pavement Performance (LTPP) Program, the Arizona Department of Transportation (ADOT) constructed five Specific Pavement Studies 9 (SPS9) test sections on U.S. Route 93 near Kingman. This project, SPS9B, studied the effe...

Classroom Research by Classroom Teachers, 1992.

ERIC Educational Resources Information Center

Tanner, Michael, Ed.

1992-01-01

This volume celebrates teachers as life-long learners of the art of teaching, by presenting 21 action research studies designed and implemented by classroom teachers. A "How To Get Started" section outlines action research steps and offers worksheets. Descriptions of the research studies begin with ethnographic studies, which include "Adopt a…

Repetitive switching for an electromagnetic rail gun

NASA Astrophysics Data System (ADS)

Gruden, J. M.

1983-12-01

Previous testing on a repetitive opening switch for inductive energy storage has proved the feasibility of the rotary switch concept. The concept consists of a rotating copper disk (rotor) with a pie-shaped insulator section and brushes which slide along each of the rotor surfaces. While on top of the copper surface, the brushes and rotor conduct current allowing the energy storage inductor to charge. When the brushes slide onto the insulator section, the current cannot pass through the rotor and is diverted into the load. This study investigates two new brush designs and a rotor modification designed to improve the current commutating capabilities of the switch. One brush design (fringe fiber) employs carbon fibers on the leading and trailing edge of the brush to increase the resistive commutating action as the switch opens and closes. The other brush design uses fingers to conduct current to the rotor surface, effectively increasing the number of brush contact points. The rotor modification was the placement of tungsten inserts at the copper-insulator interfaces.

Research on the Cross Section Precision of High-strength Steel Tube with Rectangular Section in Rotary Draw Bending

NASA Astrophysics Data System (ADS)

Yang, Hongliang; Zhao, Hao; Xing, Zhongwen

2017-11-01

For the demand of energy conservation and security improvement, high-strength steel (HSS) is increasingly being used to produce safety related automotive components. However, cross-section distortion occurs easily in bending of HSS tube with rectangular section (RS), affecting the forming precision. HSS BR1500HS tube by rotary draw bending is taken as the study object and a description method of cross-section distortion is proposed in this paper. The influence on cross-section precision of geometric parameters including cross-section position, thickness of tube, bend radius etc. are studied by experiment. Besides, simulation of the rotary draw bending of HSS tube with rectangular section by ABAQUS are carried out and compared to the experiment. The results by simulation agree well with the experiment and show that the cross-section is approximately trapezoidal after distortion; the maximum of distortion exists at 45 ∼ 60° of the bending direction; and the absolute and relative distortion values increase with the decreasing of tube thickness or bending radius. Therefore, the results can provide a reference for the design of geometric parameters of HSS tube with rectangular section in rotary draw bending.

Instructional System Design for Executive Orientation and Project Management Training Packages, Technical Memorandum No. 3. Interim Report. RF Project No. 3131-A1.

ERIC Educational Resources Information Center

Cook, Desmond L.; And Others

This memorandum reports on the third phase, the design, of a four-phase project to design project management training materials for local educational agencies. The first section of the memorandum explains some considerations regarding management education and the organization of the report. Section 2 presents the design specifications for the…

Coach simplified structure modeling and optimization study based on the PBM method

NASA Astrophysics Data System (ADS)

Zhang, Miaoli; Ren, Jindong; Yin, Ying; Du, Jian

2016-09-01

For the coach industry, rapid modeling and efficient optimization methods are desirable for structure modeling and optimization based on simplified structures, especially for use early in the concept phase and with capabilities of accurately expressing the mechanical properties of structure and with flexible section forms. However, the present dimension-based methods cannot easily meet these requirements. To achieve these goals, the property-based modeling (PBM) beam modeling method is studied based on the PBM theory and in conjunction with the characteristics of coach structure of taking beam as the main component. For a beam component of concrete length, its mechanical characteristics are primarily affected by the section properties. Four section parameters are adopted to describe the mechanical properties of a beam, including the section area, the principal moments of inertia about the two principal axles, and the torsion constant of the section. Based on the equivalent stiffness strategy, expressions for the above section parameters are derived, and the PBM beam element is implemented in HyperMesh software. A case is realized using this method, in which the structure of a passenger coach is simplified. The model precision is validated by comparing the basic performance of the total structure with that of the original structure, including the bending and torsion stiffness and the first-order bending and torsional modal frequencies. Sensitivity analysis is conducted to choose design variables. The optimal Latin hypercube experiment design is adopted to sample the test points, and polynomial response surfaces are used to fit these points. To improve the bending and torsion stiffness and the first-order torsional frequency and taking the allowable maximum stresses of the braking and left turning conditions as constraints, the multi-objective optimization of the structure is conducted using the NSGA-II genetic algorithm on the ISIGHT platform. The result of the Pareto solution set is acquired, and the selection strategy of the final solution is discussed. The case study demonstrates that the mechanical performances of the structure can be well-modeled and simulated by PBM beam. Because of the merits of fewer parameters and convenience of use, this method is suitable to be applied in the concept stage. Another merit is that the optimization results are the requirements for the mechanical performance of the beam section instead of those of the shape and dimensions, bringing flexibility to the succeeding design.

Integrating Survey and Molecular Approaches to Better Understand Wildlife Disease Ecology

PubMed Central

Cowled, Brendan D.; Ward, Michael P.; Laffan, Shawn W.; Galea, Francesca; Garner, M. Graeme; MacDonald, Anna J.; Marsh, Ian; Muellner, Petra; Negus, Katherine; Quasim, Sumaiya; Woolnough, Andrew P.; Sarre, Stephen D.

2012-01-01

Infectious wildlife diseases have enormous global impacts, leading to human pandemics, global biodiversity declines and socio-economic hardship. Understanding how infection persists and is transmitted in wildlife is critical for managing diseases, but our understanding is limited. Our study aim was to better understand how infectious disease persists in wildlife populations by integrating genetics, ecology and epidemiology approaches. Specifically, we aimed to determine whether environmental or host factors were stronger drivers of Salmonella persistence or transmission within a remote and isolated wild pig (Sus scrofa) population. We determined the Salmonella infection status of wild pigs. Salmonella isolates were genotyped and a range of data was collected on putative risk factors for Salmonella transmission. We a priori identified several plausible biological hypotheses for Salmonella prevalence (cross sectional study design) versus transmission (molecular case series study design) and fit the data to these models. There were 543 wild pig Salmonella observations, sampled at 93 unique locations. Salmonella prevalence was 41% (95% confidence interval [CI]: 37–45%). The median Salmonella DICE coefficient (or Salmonella genetic similarity) was 52% (interquartile range [IQR]: 42–62%). Using the traditional cross sectional prevalence study design, the only supported model was based on the hypothesis that abundance of available ecological resources determines Salmonella prevalence in wild pigs. In the molecular study design, spatial proximity and herd membership as well as some individual risk factors (sex, condition score and relative density) determined transmission between pigs. Traditional cross sectional surveys and molecular epidemiological approaches are complementary and together can enhance understanding of disease ecology: abundance of ecological resources critical for wildlife influences Salmonella prevalence, whereas Salmonella transmission is driven by local spatial, social, density and individual factors, rather than resources. This enhanced understanding has implications for the control of diseases in wildlife populations. Attempts to manage wildlife disease using simplistic density approaches do not acknowledge the complexity of disease ecology. PMID:23071552

HEAT EXCHANGER

DOEpatents

Fox, T.H. III; Richey, T. Jr.; Winders, G.R.

1962-10-23

A heat exchanger is designed for use in the transfer of heat between a radioactive fiuid and a non-radioactive fiuid. The exchanger employs a removable section containing the non-hazardous fluid extending into the section designed to contain the radioactive fluid. The removable section is provided with a construction to cancel out thermal stresses. The stationary section is pressurized to prevent leakage of the radioactive fiuid and to maintain a safe, desirable level for this fiuid. (AEC)

Preliminary Tests in the NACA Tank to Investigate the Fundamental Characteristics of Hydrofoils

NASA Technical Reports Server (NTRS)

Ward, Kenneth E.; Land, Norman S.

1940-01-01

This preliminary investigation was made to study the hydrodynamic properties and general behavior of simple hydrofoils. Six 5- by 30-inch plain, rectangular hydrofoils were tested in the NACA tank at various speeds, angles of attack and depths below the water surface. Two of the hydrofoils had sections representing the sections of commonly used airfoils, one had a section similar to one developed Guidoni for use with hydrofoil-equipped seaplane floats, and three had sections designed to have constant chordwise pressure distributions at given values of the lift coefficient for the purpose of delaying the speed at which cavitation begins. The experimental results are presented as curves of the lift and drag coefficients plotted against speed for the various angles of attack and depths for which the hydrofoils were tested. A number of derived curves are included for the purpose of better comparing the characteristics of the hydrofoils and to show the effects of depth. Several representative photographs show the development of cavitation on the the upper surface of the hydrofoils. The results indicate that properly designed hydrofoil sections will have excellent characteristics and that the speed at which cavitation occurs may be delayed to an appreciable extent by the use of suitable sections.

21 CFR 884.1100 - Endometrial brush.

Code of Federal Regulations, 2010 CFR

2010-04-01

... endometrium (the mucosal lining of the uterus) by brushing its surface. This device is used to study... perforation, or a recent cesarean section, and (3) Design and testing: (i) The sampling component is covered...

21 CFR 884.1100 - Endometrial brush.

Code of Federal Regulations, 2011 CFR

2011-04-01

... endometrium (the mucosal lining of the uterus) by brushing its surface. This device is used to study... perforation, or a recent cesarean section, and (3) Design and testing: (i) The sampling component is covered...

Where We Have Been and Where We Are Going: A Content Analysis of Articles Published in the Journal of Women's Health Physical Therapy From 2005 to 2015.

PubMed

Bishop, Mark D; Coronado, Rogelio A; Hill, Alexandra D; Alappattu, Meryl J

2017-05-01

The objective of this study was to examine the type and content of Journal of Women's Health Physical Therapy (JWHPT) publications over the last decade. Content and bibliometric analysis of published literature. Component sections, such as the Section on Women's Health (SoWH) of the American Physical Therapy Association provide content expertise to areas of specialty physical therapist practice, thereby supporting the dissemination of evidence for physical therapists to use. Closely aligned with the mission of the SoWH, JWHPT provides evidence reflecting this practice area. The purpose of our analysis was to examine publications within JWHPT to determine how closely JWHPT is meeting the mission and focus of section members. We used established bibliographic methodology to code and review manuscripts published online between 2005 and 2015 in JWHPT using established domains (article type, participant type, research design, study purpose, and area of focus). Total publications and proportion of publications based on domain were described. Impact by citation and author was examined using bibliometric software. Eighteen percent of the items published in JWHPT were original research papers submitted for the first time. Of those papers, the primary study design was cross-sectional experimental research, most commonly studying interventions. The primary practice area reported was management of incontinence. We suggest that a continued need to increase efforts for the submission and publication of a greater proportion of randomized controlled trials and metric articles.

Prevalence of Depressive Symptoms among Urban Adolescents of South India

ERIC Educational Resources Information Center

Mohanraj, Rani; Subbaiah, Karunanidhi

2010-01-01

Aim: This study aimed to find the prevalence of depressive symptoms among adolescents studying in schools in Chennai. Settings and Design: The study was a school based cross-sectional survey in which data were collected through a self-administered questionnaire from adolescents studying in classes X, XI and XII. Material: Beck Depression Inventory…

34 CFR 658.1 - What is the Undergraduate International Studies and Foreign Language Program?

Code of Federal Regulations, 2011 CFR

2011-07-01

... Foreign Language Program? 658.1 Section 658.1 Education Regulations of the Offices of the Department of... STUDIES AND FOREIGN LANGUAGE PROGRAM General § 658.1 What is the Undergraduate International Studies and Foreign Language Program? The Undergraduate International Studies and Foreign Language Program is designed...

34 CFR 658.1 - What is the Undergraduate International Studies and Foreign Language Program?

Code of Federal Regulations, 2010 CFR

2010-07-01

... Foreign Language Program? 658.1 Section 658.1 Education Regulations of the Offices of the Department of... STUDIES AND FOREIGN LANGUAGE PROGRAM General § 658.1 What is the Undergraduate International Studies and Foreign Language Program? The Undergraduate International Studies and Foreign Language Program is designed...

Factors Associated with Screen Time among School-Age Children in Korea

ERIC Educational Resources Information Center

Ham, Ok Kyung; Sung, Kyung Mi; Kim, Hee Kyung

2013-01-01

The purpose of this study was to investigate the association of sociodemographic, psychosocial, and behavioral characteristics with screen time among school-age children in Korea. This study employed a nonexperimental, cross-sectional study design. A total of 370 children attending four elementary schools participated in the study. Self-report…

41 CFR 60-3.14 - Technical standards for validity studies.

Code of Federal Regulations, 2010 CFR

2010-07-01

... likely to affect validity differences; or that these factors are included in the design of the study and... construct validity is both an extensive and arduous effort involving a series of research studies, which... validity studies. 60-3.14 Section 60-3.14 Public Contracts and Property Management Other Provisions...

41 CFR 60-3.14 - Technical standards for validity studies.

Code of Federal Regulations, 2013 CFR

2013-07-01

... likely to affect validity differences; or that these factors are included in the design of the study and... construct validity is both an extensive and arduous effort involving a series of research studies, which... validity studies. 60-3.14 Section 60-3.14 Public Contracts and Property Management Other Provisions...

41 CFR 60-3.14 - Technical standards for validity studies.

Code of Federal Regulations, 2014 CFR

2014-07-01

... likely to affect validity differences; or that these factors are included in the design of the study and... construct validity is both an extensive and arduous effort involving a series of research studies, which... validity studies. 60-3.14 Section 60-3.14 Public Contracts and Property Management Other Provisions...

41 CFR 60-3.14 - Technical standards for validity studies.

Code of Federal Regulations, 2011 CFR

2011-07-01

... likely to affect validity differences; or that these factors are included in the design of the study and... construct validity is both an extensive and arduous effort involving a series of research studies, which... validity studies. 60-3.14 Section 60-3.14 Public Contracts and Property Management Other Provisions...

41 CFR 60-3.14 - Technical standards for validity studies.

Code of Federal Regulations, 2012 CFR

2012-07-01

... likely to affect validity differences; or that these factors are included in the design of the study and... construct validity is both an extensive and arduous effort involving a series of research studies, which... validity studies. 60-3.14 Section 60-3.14 Public Contracts and Property Management Other Provisions...

The Participation to The All Japan College of Technology Design Competition and The Trial of Art and Design Education

NASA Astrophysics Data System (ADS)

Takeshita, Junji; Kato, Kenji

In the 2nd All Japan College of Technology Design Competition, the students majoring department of architecture (included architecture course in advanced course of Architecture and Civil Engineering) of Toyota National College of Technology won the highest award in all 3 sections of the held competition. In this paper, 2 sections of design course in awarded 3 sections was taken up. In addition, while reporting the circumstances and measure to the competition participation, the revision of a molding subject performed in recent years and the relation of this winning-a-prize result were considered.

[Application of SPSS orthogonal design in tissue culture of Anoectochilus roxburghii].

PubMed

Zhang, Fusheng; Guo, Shunxing

2009-10-01

To study the effect of the different constitutions of plant hormone on the development of Anoectochilus roxburghii. A. roxburghii were harvested after having been cultured for 60 days. An orthogonal design was used to study the effect of NAA and 6-BA on the leaf number, eustipe number, lateral branch number of the stem tip and stem section, and the height of the stem tips. All of the data were processed by SPSS. It is reported for the first time that NAA could make different development of A. roxburghii at low concentration ( < 1 mg L(-1)) and high concentration ( > 1 mg L(-1)). The optimum constitution of MS medium was NAA 0.5 mg L(-1) + 6-BA 1 mg L(-1) for the growth of the stem tip of A. roxburghii, and NAA 1 mg L(-1) + 6-BA 2 mg L(-1) for the differentiation of bud and the formation of lateral branch of the stem section. The different concentrations of NAA and 6-BA had different effects on the growth and differentiation of the stem tip and the stem section of A. roxburghii.

Translating Stem Cell Research to Cardiac Disease Therapies: Pitfalls and Prospects for Improvement

PubMed Central

Rosen, Michael R.; Myerburg, Robert J.; Francis, Darrel P.; Cole, Graham D.; Marbán, Eduardo

2014-01-01

Over the past 2 decades, there have been numerous stem cell studies focused on cardiac diseases, ranging from proof-of-concept to phase 2 trials. This series of articles focuses on the legacy of these studies and the outlook for future treatment of cardiac diseases with stem cell therapies. The first section by Rosen and Myerburg is an independent review that analyzes the basic science and translational strategies supporting the rapid advance of stem cell technology to the clinic, the philosophies behind them, trial designs, and means for going forward that may impact favorably on progress. The second and third sections were collected in response to the initial section of this review. The commentary by Francis and Cole discusses the Rosen and Myerburg review and details how trial outcomes can be affected by noise, poor trial design (particularly the absence of blinding), and normal human tendencies toward optimism and denial. The final, independent article by Marbán takes a different perspective concerning the potential for positive impact of stem cell research applied to heart disease and future prospects for its clinical application. PMID:25169179

Conceptual design of a fleet of autonomous regolith throwing devices for radiation shielding of lunar habitats

NASA Technical Reports Server (NTRS)

Armstrong, Karem; Mcadams, Daniel A.; Norrell, Jeffery L.

1992-01-01

The National Aeronautics and Space Administration (NASA) in conjunction with Universities Space Research Association (USRA) has requested that the feasibility of a fleet of regolith tossing devices designed to cover a lunar habitat for radiation protection be demonstrated. The regolith, or lunar soil, protects the lunar habitat and its inhabitants from radiation. Ideally, the device will operate autonomously in the lunar environment. To prove the feasibility of throwing regolith on the Moon, throwing solutions were compared to traditional, Earth-based methods for moving soil. Various throwing configurations were investigated. A linear throwing motion combined with a spring and motor energizing system proved a superior solution. Three different overall configurations for the lunar device are presented. A single configuration is chosen and critical parameters such as operating procedure, system volume, mass, and power are developed. The report is divided into seven main sections. First, the Introduction section gives background information, defines the project requirements and the design criteria, and presents the methodology used for the completion of this design. Next, the Preliminary Analysis section presents background information on characteristics of lunar habitats and the lunar environment. Then, the Alternate Designs section presents alternate solutions to each of the critical functions of the device. Fourth, a detailed analysis of throwing the regolith is done to demonstrate its feasibility. Then, the three overall design configurations are presented. Next, a configuration is selected and the conceptual design is expanded to include system performance characteristics, size, and mass. Finally, the Conclusions and Recommendations for Future Work section evaluates the design, outlines the next step to be taken in the design process, and suggests possible goals for future design work.

30 CFR 715.18 - Dams constructed of or impounding waste material.

Code of Federal Regulations, 2011 CFR

2011-07-01

... existing or new dams without the approval of the regulatory authority. The permittee shall design, locate... design precipitation event within 10 days. (viii) During construction of dams subject to this section... adjacent to each dam within 30 days of certification of design pursuant to this section. (4) All dams...

26 CFR 1.852-9 - Special procedural requirements applicable to designation under section 852(b)(3)(D).

Code of Federal Regulations, 2010 CFR

2010-04-01

..., DEPARTMENT OF THE TREASURY (CONTINUED) INCOME TAX (CONTINUED) INCOME TAXES Regulated Investment Companies and Real Estate Investment Trusts § 1.852-9 Special procedural requirements applicable to designation under section 852(b)(3)(D). (a) Regulated investment company—(1) Notice to shareholders. (i) A designation of...

Design, Development, Implementation, and Evaluation of the Computer Aided Interactive Testing System (CAITS). Focus on the Trained Person.

ERIC Educational Resources Information Center

1983

This report describes the design, development, implementation, and evaluation of the Computer Aided Interactive Testing System (CAITS) and addresses the applicability of the system in the Naval Education and Training Command. In addition to an introduction (section one), the report contains four sections and three appendices. Section two describes…

Home Centered Care: Designing a Family Day Care Program. A Guide for Caregivers and Parents.

ERIC Educational Resources Information Center

Garcia, Ronda

Consistent in its approach to child development and caregiving concepts, this guide for parents and child caregivers explores aspects of family day care in five sections. Section I discusses the design of physically safe environments for children. Section II describes the developing likes and needs of infants, toddlers, preschool children, and…

Axial Crushing of Thin-Walled Columns with Octagonal Section: Modeling and Design

NASA Astrophysics Data System (ADS)

Liu, Yucheng; Day, Michael L.

This chapter focus on numerical crashworthiness analysis of straight thinwalled columns with octagonal cross sections. Two important issues in this analysis are demonstrated here: computer modeling and crashworthiness design. In the first part, this chapter introduces a method of developing simplified finite element (FE) models for the straight thin-walled octagonal columns, which can be used for the numerical crashworthiness analysis. Next, this chapter performs a crashworthiness design for such thin-walled columns in order to maximize their energy absorption capability. Specific energy absorption (SEA) is set as the design objective, side length of the octagonal cross section and wall thickness are selected as design variables, and maximum crushing force (Pm) occurs during crashes is set as design constraint. Response surface method (RSM) is employed to formulate functions for both SEA and Pm.

Design guidelines for wind-resistant structures

DOE Office of Scientific and Technical Information (OSTI.GOV)

McDonald, J.R.; Mehta, K.C.; Minor, J.E.

1975-06-01

The purpose of this document is to prescribe criteria and to provide guidance for professional personnel who are involved in the design and evaluation of buildings and structures to resist tornadoes and extreme winds at the Oak Ridge, Tennessee, Portsmouth, Ohio, and Paducah, Kentucky, Plant Sites. The scope of the document covers loads due to extreme winds and tornadoes. Other loading conditions such as dead, live, or earthquake loads shall be considered as prescribed by the Union Carbide Corporation. In Section II the method for determining the maximum design windspeed for any specified level of risk is described. The straightmore » wind and tornado parameters are then deduced from the value of maximum design windspeed. The three types of tornado and extreme wind loads (aerodynamic, atmospheric pressure change and missiles) are treated in Sections III, IV, and V, respectively. Appropriate load combinations are defined in Section VI. The final section contains several examples showing how the design guidelines are used to determine appropriate design wind pressures. A description of the computer program used to predict missile accelerations, velocities and trajectories is contained in Appendix A. Additional design examples are provided in Appendix B.« less

Project Exodus

NASA Technical Reports Server (NTRS)

1990-01-01

Project Exodus is an in-depth study to identify and address the basic problems of a manned mission to Mars. The most important problems concern propulsion, life support, structure, trajectory, and finance. Exodus will employ a passenger ship, cargo ship, and landing craft for the journey to Mars. These three major components of the mission design are discussed separately. Within each component the design characteristics of structures, trajectory, and propulsion are addressed. The design characteristics of life support are mentioned only in those sections requiring it.

Ergonomics and design: its principles applied in the industry.

PubMed

Tavares, Ademario Santos; Silva, Francisco Nilson da

2012-01-01

Industrial Design encompasses both product development and optimization of production process. In this sense, Ergonomics plays a fundamental role, because its principles, methods and techniques can help operators to carry out their tasks most successfully. A case study carried out in an industry shows that the interaction among Design, Production Engineering and Materials Engineering departments may improve some aspects concerned security, comfort, efficiency and performance. In this process, Ergonomics had shown to be of essential importance to strategic decision making to the improvement of production section.

Megawatt Space Power Conditioning, Distribution, and Control Study

DTIC Science & Technology

1988-03-01

also must be given to the design of an ac transmission line for this relatively high frequency . 2.3.2 Medium High Voltage Systems. Figure 2-4 shows a...systems are designed to exploit the use of 2 MW klystrode tubes (see Section 3.1) which require a dc voltage of about 140 kV. This high voltage can be...the concerns is that to date there have been no three-phase high voltage, high frequency transmission lines designed . Figure 5-6. While the previous

Groundwater contamination downstream of a contaminant penetration site. II. Horizontal penetration of the contaminant plume

USGS Publications Warehouse

Rubin, H.; Buddemeier, R.W.

2002-01-01

Part I of this study (Rubin, H.; Buddemeier, R.W. Groundwater Contamination Downstream of a Contaminant Penetration Site Part 1: Extension-Expansion of the Contaminant Plume. J. of Environmental Science and Health Part A (in press).) addressed cases, in which a comparatively thin contaminated region represented by boundary layers (BLs) developed within the freshwater aquifer close to contaminant penetration site. However, at some distance downstream from the penetration site, the top of the contaminant plume reaches the top or bottom of the aquifer. This is the location of the "attachment point," which comprises the entrance cross section of the domain evaluated by the present part of the study. It is shown that downstream from the entrance cross section, a set of two BLs develop in the aquifer, termed inner and outer BLs. It is assumed that the evaluated domain, in which the contaminant distribution gradually becomes uniform, can be divided into two sections, designated: (a) the restructuring section, and (b) the establishment section. In the restructuring section, the vertical concentration gradient leads to expansion of the inner BL at the expense of the outer BL, and there is almost no transfer of contaminant mass between the two layers. In the establishment section, each of the BLs occupies half of the aquifer thickness, and the vertical concentration gradient leads to transfer of contaminant mass from the inner to the outer BL. By use of BL approximations, changes of salinity distribution in the aquifer are calculated and evaluated. The establishment section ends at the uniformity point, downstream from which the contaminant concentration profile is practically uniform. The length of the restructuring section, as well as that of the establishment section, is approximately proportional to the aquifer thickness squared, and is inversely proportional to the transverse dispersivity. The study provides a convenient set of definitions and terminology that are helpful in visualizing the gradual development of uniform contaminant concentration distribution in an aquifer subject to contaminant plume penetration. The method developed in this study can be applied to a variety of problems associated with groundwater quality, such as initial evaluation of field data, design of field data collection, the identification of appropriate boundary conditions for numerical models, selection of appropriate numerical modeling approaches, interpretation and evaluation of field monitoring results, etc.

Hospital board effectiveness: relationships between governing board composition and hospital financial viability.

PubMed Central

Molinari, C; Morlock, L; Alexander, J; Lyles, C A

1993-01-01

OBJECTIVE. Two theories--agency and managerialism--are compared with respect to their usefulness in explaining the role of insiders on the hospital board: whether their participation enhances or impairs board financial decision making. DATA SOURCES/STUDY SETTING. The study used 1985 hospital financial and governing board data for a representative sample of acute care California hospitals. STUDY DESIGN. Relationships were examined cross-sectionally between the presence or absence of insiders on the board and measures of hospital financial viability while controlling for the organizational factors of system affiliation, ownership, size, region, and corporate restructuring. PRINCIPAL FINDINGS. Multiple regression analysis found significant relationships between insider (CEO, medical staff) participation and hospital viability. CONCLUSIONS. These results support the managerial theory of governance by suggesting that the CEO and medical staff provide informational advantages to the hospital governing board. However, the cross-sectional design points to the need for future longitudinal studies in order to sequence these relationships between insider participation and improved hospital viability. PMID:8344824

Control-Structure-Interaction (CSI) technologies and trends to future NASA missions

NASA Technical Reports Server (NTRS)

1990-01-01

Control-structure-interaction (CSI) issues which are relevant for future NASA missions are reviewed. This goal was achieved by: (1) reviewing large space structures (LSS) technologies to provide a background and survey of the current state of the art (SOA); (2) analytically studying a focus mission to identify opportunities where CSI technology may be applied to enhance or enable future NASA spacecraft; and (3) expanding a portion of the focus mission, the large antenna, to provide in-depth trade studies, scaling laws, and methodologies which may be applied to other NASA missions. Several sections are presented. Section 1 defines CSI issues and presents an overview of the relevant modeling and control issues for LLS. Section 2 presents the results of the three phases of the CSI study. Section 2.1 gives the results of a CSI study conducted with the Geostationary Platform (Geoplat) as the focus mission. Section 2.2 contains an overview of the CSI control design methodology available in the technical community. Included is a survey of the CSI ground-based experiments which were conducted to verify theoretical performance predictions. Section 2.3 presents and demonstrates a new CSI scaling law methodology for assessing potential CSI with large antenna systems.

Motion of an Articulated Vehicle with Two-Dimensional Sections Subject to Lateral Obstacles

NASA Astrophysics Data System (ADS)

Antonyuk, E. Ya.; Zabuga, A. T.

2016-07-01

Some aspects of the geometry, kinematics, and dynamics of a three-section robotic vehicle with a front steerable wheel are studied. The constraints between the wheels and the flat ground are assumed nonholonomic. The vehicle moves in a narrow L-shaped corridor. A path for the characteristic points of the sections of the robot is designed. A dynamic model of the system is developed. The maximum possible dimensions of the robot that allow its unimpeded and non-stop motion are determined. The kinetostatic analysis of the load on a three-section vehicle moving along a planned path is modeled. The holonomic and nonholonomic constraint reactions between the wheels and the ground and in the joints between the sections are determined

An Updated Review of Epidemiologic Studies on the Relationship Between Exposure to Whole-Body Vibration and Low Back Pain

NASA Astrophysics Data System (ADS)

Bovenzi, M.; Hulshof, C. T. J.

1998-08-01

The aim of this paper is to update the information on the epidemiologic evidence of the adverse health effects of whole-body vibration (WBV) on the spinal system by means of a review of the epidemiologic studies published between 1986 and 1996. In a systematic search of epidemiologic studies of low back pain (LBP) disorders and occupations with exposure to WBV, 37 articles were retrieved. The quality of each study was evaluated according to criteria concerning the assessment of vibration exposure, assessment of health effects, and methodology. The epidemiologic studies reaching an adequate score on each of the above mentioned criteria, were included in the final review. A meta-analysis was also conducted in order to combine the results of independent epidemiologic studies. After applying the selection criteria, 16 articles reporting the occurrence of LBP disorders in 19 WBV-exposed occupational groups, reached a sufficient score. The study design was cross-sectional for 13 occupational groups, longitudinal for 5 groups and of case-control type for one group. The main reasons for the exclusion of studies were insufficient quantitative information on WBV exposure and the lack of control groups. The findings of the selected studies and the results of the meta-analysis of both cross-sectional and cohort studies showed that occupational exposure to WBV is associated with an increased risk of LBP, sciatic pain, and degenerative changes in the spinal system, including lumbar intervertebral disc disorders. Owing to the cross-sectional design of the majority of the reviewed studies, this epidemiologic evidence is not sufficient to outline a clear exposure-response relationship between WBV exposure and LBP disorders. Upon comparing the epidemiological studies included in this review with those conducted before 1986, it is concluded that research design and the quality of exposure and health effect data in the field of WBV have improved in the last decade.

Bibliometric analysis of scientific articles published in Brazilian and international orthodontic journals over a 10-year period

PubMed Central

Primo, Neudí Antonio; Gazzola, Vivian Bertoglio; Primo, Bruno Tochetto; Tovo, Maximiano Ferreira; Faraco Junior, Italo Medeiros

2014-01-01

Objective This study aimed at describing the profiles of Brazilian and international studies published in orthodontic journals. Methods The sample comprised 635 articles selected from two scientific journals, i.e., Dental Press Journal of Orthodontics and American Journal of Orthodontics and Dentofacial Orthopedics, which were analyzed at three different intervals over a 10-year period (1999 - 2004 - 2009). Articles were described in terms of knowledge domain, study design, and country of origin (or state of origin for Brazilian papers). Results The most frequent study designs adopted in international studies were cohort (23.9%) and cross-sectional (21.7%) designs. Among Brazilian papers, cross-sectional studies (28.9%) and literature reviews (24.6%) showed greater frequency. The topics most often investigated were dental materials (17%) and treatment devices (12.4%) in international articles, with the latter topic being addressed by 16% of the Brazilian publications, followed by malocclusion, with 12.6%. In all cases, the most frequent countries of origin coincided with the countries of origin of each journal. Conclusions The majority of the studies analyzed featured a low level of scientific evidence. Moreover, the findings showed that journals tend to publish studies produced in their own country of origin, and that there are marked discrepancies in the number of papers published by different Brazilian states. PMID:24945515

Design and Numerical Simulation of Radial Inflow Turbine Volute

NASA Astrophysics Data System (ADS)

Shah, Samip P.; Channiwala, S. A.; Kulshreshtha, D. B.; Chaudhari, Gaurang

2014-12-01

The volute of a radial inflow turbine has to be designed to ensure that the desired rotor inlet conditions like absolute Mach number, flow angle etc. are attained. For the reasonable performance of vaneless volute turbine care has to be taken for reduction in losses at an appropriate flow angle at the rotor inlet, in the direction of volute, whose function is to convert gas energy into kinetic energy and direct the flow towards the rotor inlet at an appropriate flow angle with reduced losses. In literature it was found that the incompressible approaches failed to provide free vortex and uniform flow at rotor inlet for compressible flow regimes. So, this paper describes a non-dimensional design procedure for a vaneless turbine volute for compressible flow regime and investigates design parameters, such as the distribution of area ratio and radius ratio as a function of azimuth angle. The nondimensional design is converted in dimensional form for three different volute cross sections. A commercial computational fluid dynamics code is used to develop numerical models of three different volute cross sections. From the numerical models, losses generation in the different volutes are identified and compared. The maximum pressure loss coefficient for Trapezoidal cross section is 0.1075, for Bezier-trapezoidal cross section is 0.0677 and for circular cross section is 0.0438 near tongue region, which suggested that the circular cross section will give a better efficiency than other types of volute cross sections.

Systems design study of the Pioneer Venus spacecraft. Volume 1. Technical analyses and tradeoffs, sections 1-4 (part 1 of 4)

NASA Technical Reports Server (NTRS)

1973-01-01

The results are reported of the Pioneer Venus studies from 2 October 1972 through 30 June 1973. Many missions were considered, involving two launch vehicles (Thor/Delta and Atlas/Centaur), and different launch opportunities and spacecraft configurations to meet varying science requirements, all at minimum cost. The sequence of events is described and the specific studies conducted are summarized. The effects of science payload on mission and spacecraft design are discussed along with the mission analyses.

Design integration and noise studies for jet STOL aircraft. Volume 1: Program summary

NASA Technical Reports Server (NTRS)

Okeefe, V. O.; Kelley, G. S.

1972-01-01

This program was undertaken to develop, through analysis, design, experimental static testing, wind tunnel testing, and design integration studies, an augmentor wing jet flap configuration for a jet STOL transport aircraft having maximum propulsion and aerodynamic performance with minimum noise generation. The program had three basic elements: (1) static testing of a scale wing section to demonstrate augmentor performance and noise characteristics; (2) two-dimensional wind tunnel testing to determine flight speed effects on performance; and (3) system design and evaluation which integrated the augmentor information obtained into a complete system and ensured that the design was compatible with the requirements for a large STOL transport having a 500-ft sideline noise of 95 PNdB or less. This objective has been achieved.

Development of a hydro kinetic river turbine with simulation and operational measurement results in comparison

NASA Astrophysics Data System (ADS)

Ruopp, A.; Ruprecht, A.; Riedelbauch, S.; Arnaud, G.; Hamad, I.

2014-03-01

The development of a hydro-kinetic prototype was shown including the compound structure, guide vanes, runner blades and a draft tube section with a steeply sloping, short spoiler. The design process of the hydrodynamic layout was split into three major steps. First the compound and the draft tube section was designed and the best operating point was identified using porous media as replacement for the guide vane and runner section (step one). The best operating point and the volume flux as well as the pressure drop was identified and used for the design of the guide vane section and the runner section. Both were designed and simulated independently (step two). In step three, all parts were merged in stationary simulation runs detecting peak power and operational bandwidth. In addition, the full scale demonstrator was installed in August 2010 and measured in the St. Lawrence River in Quebec supporting the average inflow velocity using ADCP (Acoustic Doppler Current Profiler) and the generator power output over the variable rotational speed. Simulation data and measurements are in good agreement. Thus, the presented approach is a suitable way in designing a hydro kinetic turbine.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dahl, P.F.

The magnet system for the Superconducting Super Collider will likely remain the most ambitions-and challenging-application of superconducting technology for the foreseeable future. The centerpiece of the system is the behemoth collider dipole magnet. Its design, still evolving in its detailed features, dates from the mid-1980's when it emerged as the winter in an early technical showdown that occupied the fledgling SSC project. In the present report we chronicle the origins and chief milestones in the development of certain SSC dipole design concepts. Unfortunately, the chronicle must remain incomplete, with the design not yet frozen as we go to press andmore » still subject to important modifications as the SSC Laboratory settles in near its future home in Ellis County, Texas, hard on the heels of a wide-ranging design review in the closing days of the SSC Central Design Group in (CDG) Berkeley. Be that as it may, in what follows we concentrate on the early years in an attempt to recapitulate the birth of the dipole, taking as our point of departure the SSC Reference Designs Study (RDS) of 1984. In Section 3 we touch on the background for the various RDS options, including ISABELLE/CBA and the Tevatron. In Section 4 the narrative focuses on the two final protagonists, a high-field cosine theta (cos {theta}) magnet and a low-field superferric magnet. Section 5 recounts the circumstances surrounding the selection of a particular magnet style'' for further development, and the ups and downs of the first model magnets. We conclude with a smattering of progress highlights in refining the design during the final push under the reign of the CDG. Beyond that, the ongoing chronicle must be left for others to amplify and complete.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dahl, P.F.

The magnet system for the Superconducting Super Collider will likely remain the most ambitions-and challenging-application of superconducting technology for the foreseeable future. The centerpiece of the system is the behemoth collider dipole magnet. Its design, still evolving in its detailed features, dates from the mid-1980`s when it emerged as the winter in an early technical showdown that occupied the fledgling SSC project. In the present report we chronicle the origins and chief milestones in the development of certain SSC dipole design concepts. Unfortunately, the chronicle must remain incomplete, with the design not yet frozen as we go to press andmore » still subject to important modifications as the SSC Laboratory settles in near its future home in Ellis County, Texas, hard on the heels of a wide-ranging design review in the closing days of the SSC Central Design Group in (CDG) Berkeley. Be that as it may, in what follows we concentrate on the early years in an attempt to recapitulate the birth of the dipole, taking as our point of departure the SSC Reference Designs Study (RDS) of 1984. In Section 3 we touch on the background for the various RDS options, including ISABELLE/CBA and the Tevatron. In Section 4 the narrative focuses on the two final protagonists, a high-field cosine theta (cos {theta}) magnet and a low-field superferric magnet. Section 5 recounts the circumstances surrounding the selection of a particular magnet ``style`` for further development, and the ups and downs of the first model magnets. We conclude with a smattering of progress highlights in refining the design during the final push under the reign of the CDG. Beyond that, the ongoing chronicle must be left for others to amplify and complete.« less

Design and performance of controlled-diffusion stator compared with original double-circular-arc stator

NASA Technical Reports Server (NTRS)

Gelder, Thomas F.; Schmidt, James F.; Suder, Kenneth L.; Hathaway, Michael D.

1987-01-01

The capabilities of two stators, one with controlled-diffusion (CD) blade sections and one with double-circular-arc (DCA) blade sections, were compared. A CD stator was designed and tested that had the same chord length but half the blades of the DCA stator. The same fan rotor (tip speed, 429 m/sec; pressure ratio, 1.65) was used with each stator row. The design and analysis system is briefly described. The overall stage and rotor performances with each stator are compared, as are selected blade element data. The minimum overall efficiency decrement across the stator was approximately 1 percentage point greater with the CD balde sections than with the DCA blade sections.

Design and performance of controlled-diffusion stator compared with original double-circular-arc stator

NASA Technical Reports Server (NTRS)

Gelder, Thomas F.; Schmidt, James F.; Suder, Kenneth L.; Hathaway, Michael D.

1987-01-01

The capabilities of two stators, one with controlled-diffusion (CD) blade sections and one with double-circular-arc (DCA) blade sections, were compared. A CD stator was designed and tested that had the same chord length but half the blades of the DCA stator. The same fan rotor (tip speed, 429 m/sec; pressure ratio, 1.65) was used with each stator row. The design and analysis system is briefly described. The overall stage and rotor performances with each stator are compared, as are selected blade element data. The minimum overall efficiency decrement across the stator was approximately 1 percentage point greater with the CD blade sections than with the DCA blade sections.

Low-Cost Jet Fuel Starter Design Study

DTIC Science & Technology

1974-12-02

2G 27 3^ 38 & 39 60 vi WflU I LIST OF TABLES (continued) TABLE NO, 7 D-l I>-2 TITLE PAGE NO, Sea Level Design Point Component...Improvements 60 Turbojet Performance Summary D-3 Turbofan Performance Summary D-5 vii 1 SECTION INTRODUCTION The purpose of this study was to define...temperature difference between the top and bot- tom of the starter, does not begin to have an effect until after 60 seconds from shutdown. The Jet fuel

Engineering report. Part 2: NASA wheel and brake material tradeoff study for space shuttle type environmental requirements

NASA Technical Reports Server (NTRS)

Bok, L. D.

1973-01-01

The study included material selection and trade-off for the structural components of the wheel and brake optimizing weight vs cost and feasibility for the space shuttle type application. Analytical methods were used to determine section thickness for various materials, and a table was constructed showing weight vs. cost trade-off. The wheel and brake were further optimized by considering design philosophies that deviate from standard aircraft specifications, and designs that best utilize the materials being considered.

The Strengthening the Reporting of Observational Studies in Epidemiology (STROBE) Statement: guidelines for reporting observational studies.

PubMed

von Elm, Erik; Altman, Douglas G; Egger, Matthias; Pocock, Stuart J; Gøtzsche, Peter C; Vandenbroucke, Jan P

2014-12-01

Much biomedical research is observational. The reporting of such research is often inadequate, which hampers the assessment of its strengths and weaknesses and of a study's generalisability. The Strengthening the Reporting of Observational Studies in Epidemiology (STROBE) Initiative developed recommendations on what should be included in an accurate and complete report of an observational study. We defined the scope of the recommendations to cover three main study designs: cohort, case-control, and cross-sectional studies. We convened a 2-day workshop in September 2004, with methodologists, researchers, and journal editors to draft a checklist of items. This list was subsequently revised during several meetings of the coordinating group and in e-mail discussions with the larger group of STROBE contributors, taking into account empirical evidence and methodological considerations. The workshop and the subsequent iterative process of consultation and revision resulted in a checklist of 22 items (the STROBE Statement) that relate to the title, abstract, introduction, methods, results, and discussion sections of articles. 18 items are common to all three study designs and four are specific for cohort, case-control, or cross-sectional studies. A detailed Explanation and Elaboration document is published separately and is freely available on the Web sites of PLoS Medicine, Annals of Internal Medicine, and Epidemiology. We hope that the STROBE Statement will contribute to improving the quality of reporting of observational studies. Copyright © 2014 The Authors. Published by Elsevier Ltd.. All rights reserved.

Evaluating Learning Management System (LMS)-facilitated Delivery of Universal Design for Learning (UDL)

NASA Astrophysics Data System (ADS)

Bryans Bongey, Sarah

This quantitative study involved 157 students in two sections of an undergraduate class in general biology, as well as one instructor who taught both sections of the course. It used resources from the Center for Applied Special Technologies (CAST) to evaluate the viability of a Learning Management System (LMS) to provide Universal Design for Learning (UDL). It also measured and tracked the instructor's level of efficacy in sustaining UDL approaches throughout the semester. In an effort to identify the UDL's specific outcomes or benefits to students, this study used a pre- and post- test to identify the treatment's impact on student engagement. Findings indicated that the LMS could be designed to comply with UDL guidelines, and the instructor was able to establish a high level of efficacy in maintaining that UDL design. However, based on the statistical analysis of pre- and post-test responses from control vs. treatment groups of students, the treatment was seen to have no significant effect in the area of student engagement. Overall, the study added to the literature by suggesting (a) the viability of the LMS as a means of providing UDL approaches, (b) the promise of the LMS as a tool faculty can use to deliver UDL with a high level of efficacy, and (c) the design's lack of effect in the area of student engagement. The fact that this study was limited to a single brand of LMS (Blackboard), a single instructor, and a single group of students underscores the need for further research.

Analysis of Potential Energy Corridors Proposed by the Western Electricity Coordinating Council

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kuiper, James A.; Cantwell, Brian J.; Hlava, Kevin J.

2014-02-24

This report, Analysis of Potential Energy Corridors Proposed by the Western Electricity Coordinating Council (WECC), was prepared by the Environmental Science Division of Argonne National Laboratory (Argonne). The intent of WECC’s work was to identify planning-level energy corridors that the Department of Energy (DOE) and its affiliates could study in greater detail. Argonne was tasked by DOE to analyze the WECC Proposed Energy Corridors in five topic areas for use in reviewing and revising existing corridors, as well as designating additional energy corridors in the 11 western states. In compliance with Section 368 of the Energy Policy Act of 2005more » (EPAct), the Secretaries of Energy, Agriculture, and the Interior (Secretaries) published a Programmatic Environmental Impact Statement in 2008 to address the proposed designation of energy transport corridors on federal lands in the 11 western states. Subsequently, Records of Decision designating the corridors were issued in 2009 by the Bureau of Land Management (BLM) and the U.S. Forest Service (USFS). The 2012 settlement of a lawsuit, brought by The Wilderness Society and others against the United States, which identified environmental concerns for many of the corridors requires, among other things, periodic reviews of the corridors to assess the need for revisions, deletions, or additions. A 2013 Presidential Memorandum requires the Secretaries to undertake a continuing effort to identify and designate energy corridors. The WECC Proposed Energy Corridors and their analyses in this report provide key information for reviewing and revising existing corridors, as well as designating additional energy corridors in the 11 western states. Load centers and generation hubs identified in the WECC analysis, particularly as they reflect renewable energy development, would be useful in reviewing and potentially updating the designated Section 368 corridor network. Argonne used Geographic Information System (GIS) technology to analyze the proposed energy corridors in the WECC report in five topic areas: Federal land jurisdiction, Existing Section 368 corridors, Existing transmission lines, Previously studied corridor locations, and Protected areas. Analysis methods are explained and tables and maps are provided to describe the results of the analyses in all five topic areas. WECC used a rational approach to connecting the hubs it identified, although there may be opportunities for adapting some of the proposed WECC routes to previously designated Section 368 corridors, for example: The WECC proposed energy corridors are in fact centerlines of proposed routes connecting hubs of various descriptions related to electric energy transmission. Although the centerlines were sited to avoid sensitive areas, infrastructure proposed within actual pathways or corridors defined by the centerlines would sometimes affect lands where such development would not normally be allowed, such as National Parks and Monuments, National Wildlife Refuges, and Wilderness Areas. Many WECC proposed energy corridors are sited along centerlines of existing roads, including Interstate Highways, where in some cases additional width to accommodate energy transmission infrastructure may not be available. Examples include the WECC Proposed Corridor along Interstate 70 through Glenwood Canyon in Colorado, and along U.S. Highway 89 across Glen Canyon Dam in Arizona. Several WECC proposed energy corridors are parallel to designated Section 368 corridors that have already cleared the preliminary steps to right-of-way approval. In many of these cases, the WECC hub connection objectives can be met more efficiently by routing on the designated Section 368 corridors.« less

Another look at the safety effects of horizontal curvature on rural two-lane highways.

PubMed

Saleem, Taha; Persaud, Bhagwant

2017-09-01

Crash Modification Factors (CMFs) are used to represent the effects on crashes of changes to highway design elements and are usually obtained from observational studies based on reported crashes. The design element of interest for this paper is horizontal curvature on rural 2-lane highways. The data for this study came from the Washington State database in the Highway Safety Information System (HSIS). Crash prediction models are developed for curve sections on rural 2-lane highway and the tangent sections up- and down-stream of the curve sections. Different negative binomial models were developed for segments on level grades (<3%), moderate grades (3-6%), and steep grades (>6%) to account for the confounding effects of gradient. The relationships between crashes at different traffic volumes and deflection angles are explored to illustrate how to get estimates of CMFs for increases in the minimum radius, considering the effect of increased tangent length for sharper curves, an effect that is overlooked in the Highway Safety Manual CMF, in addition to the effect of gradient. The results of that exploration indicated that even at different design speeds and deflection angles, the CMF estimates for incremental increases in radius lie within the same range, and that the crash reduction rate (CRR) is higher at segments on higher grades compared to the ones on lower grades. Copyright © 2017 Elsevier Ltd. All rights reserved.

77 FR 31625 - Center For Scientific Review; Notice of Closed Meetings

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-29

... Integrated Review Group, Biostatistical Methods and Research Design Study Section. Date: June 22, 2012. Time... Domestic Assistance Program Nos. 93.306, Comparative Medicine; 93.333, Clinical Research, 93.306, 93.333...

Ironbound Research Project

DOT National Transportation Integrated Search

2002-12-01

The Infrastructure Design Lab of the New Jersey School of Architecture, with the assistance of NCTIP, is working with the Business Improvement District (BID) of the historic Ironbound section of Newark to study various plans that have been prepared f...

Cost model relationships between textile manufacturing processes and design details for transport fuselage elements

NASA Technical Reports Server (NTRS)

Metschan, Stephen L.; Wilden, Kurtis S.; Sharpless, Garrett C.; Andelman, Rich M.

1993-01-01

Textile manufacturing processes offer potential cost and weight advantages over traditional composite materials and processes for transport fuselage elements. In the current study, design cost modeling relationships between textile processes and element design details were developed. Such relationships are expected to help future aircraft designers to make timely decisions on the effect of design details and overall configurations on textile fabrication costs. The fundamental advantage of a design cost model is to insure that the element design is cost effective for the intended process. Trade studies on the effects of processing parameters also help to optimize the manufacturing steps for a particular structural element. Two methods of analyzing design detail/process cost relationships developed for the design cost model were pursued in the current study. The first makes use of existing databases and alternative cost modeling methods (e.g. detailed estimating). The second compares design cost model predictions with data collected during the fabrication of seven foot circumferential frames for ATCAS crown test panels. The process used in this case involves 2D dry braiding and resin transfer molding of curved 'J' cross section frame members having design details characteristic of the baseline ATCAS crown design.

Experimental investigations of aeration efficiency in high-head gated circular conduits.

PubMed

Cihat Tuna, M; Ozkan, Fahri; Baylar, Ahmet

2014-01-01

The primary purpose of water aeration is to increase the oxygen saturation of the water. This can be achieved by using hydraulic structures because of substantial air bubble entrainment at these structures. Closed conduit aeration is a particular instance of this. While there has been a great deal of research on air-demand ratio within closed conduit, very little research has specifically addressed aeration efficiency of closed conduit. In the present work an experimental study was conducted to investigate the aeration efficiency of high-head gated circular conduits. Results showed that high-head gated circular conduits were effective for oxygen transfer. The effects of Froude number and ratio of the water cross-sectional flow area to the conduit cross-sectional area on aeration efficiency were particularly significant, whereas the effect of conduit length was only moderate. Further, a design formula for the aeration efficiency was presented relating the aeration efficiency to ratio of water cross-sectional flow area to conduit cross-sectional area and Froude number. The obtained results will be useful in future modeling processes and aid the practicing engineer in predicting aeration efficiency for design purposes.

Draw-and-Write Technique Elicits Children's Perceptions of Health in the USA and Guatemala

ERIC Educational Resources Information Center

Renslow, Jillian; Maupin, Jonathan

2018-01-01

Objective: Using the draw-and-write methodology, this study examined cross-cultural similarities and differences in children's perceptions of health. Design: Cross-sectional design. Setting: One public elementary school in the USA and in Guatemala. Method: The total sample included 161 children 9-10 years of age, 80 in the USA and 81 in Guatemala.…

Final Report for Dynamic Models for Causal Analysis of Panel Data. Methods for Temporal Analysis. Part I, Chapter 1.

ERIC Educational Resources Information Center

Hannan, Michael T.; Tuma, Nancy Brandon

This document is part of a series of chapters described in SO 011 759. Working from the premise that temporal analysis is indispensable for the study of change, the document examines major alternatives in research design of this nature. Five sections focus on the features, advantages, and limitations of temporal analysis. Four designs which…

Porter's Five Competitive Forces Framework and Other Factors That Influence the Choice of Response Strategies Adopted by Public Universities in Kenya

ERIC Educational Resources Information Center

Mathooko, Francis M.; Ogutu, Martin

2015-01-01

Purpose: The purpose of this paper is to establish the extent to which Porter's five competitive forces (PFCF) framework, among other factors drive the choice of response strategies adopted by public universities in Kenya. Design/Methodology/Approach: The study design was descriptive and utilized a cross-sectional survey of all the public…

The United States and Canada: A Common Heritage, a Shared Future.

ERIC Educational Resources Information Center

Blankenship, Glen; And Others

Designed to familiarize students with Canada and how it compares and contrasts with the United States, this collection of 18 lessons is designed to be used in a variety of ways. The lessons may be used individually, infused as case studies into a variety of course topics or used as a complete unit. Each lesson is divided into six sections: lesson…

CORRELATES OF RECOVERY FROM ALCOHOL DEPENDENCE: A PROSPECTIVE STUDY OVER A 3-YEAR FOLLOW-UP INTERVAL

PubMed Central

Dawson, Deborah A.; Goldstein, Risë B.; Ruan, W. June; Grant, Bridget F.

2011-01-01

Background Correlates of recovery from alcohol dependence have been identified through a variety of study designs characterized by different strengths and limitations. The goal of this study was to compare correlates of recovery based on a 3-year prospective design with those based on cross-sectional analyses of data from the same source. Methods Data from the 2001-2002 Wave 1 and 2004-2005 Wave 2 National Epidemiologic Survey on Alcohol and Related Conditions (NESARC) were used to examine baseline characteristics associated with Wave 2 recovery from alcohol dependence, among those who classified with past-year DSM-IV alcohol dependence at Wave 1 (n=1,172). Results Abstinent recovery (AR) was significantly associated with Black/Asian/Hispanic race/ethnicity, children <1 year of age in the household at baseline, attending religious services ≥weekly at follow-up, and having initiated help seeking that comprised/included 12-step participation within <3 years prior to baseline. Nonabstinent recovery (NR) was positively associated with being never married at baseline, having job problems or being unemployed in the year preceding baseline, attending religious services

SSME alternate turbopump (pump section) axial load analysis

NASA Technical Reports Server (NTRS)

Crease, G. A.; Rosello, A., Jr.; Fetfatsidis, A. K.

1989-01-01

A flow balancing computer program constructed to calculate the axial loads on the Space Shuttle Main Engine (SSME) alternate turbopumps (ATs) pump sections are described. The loads are used in turn to determine load balancing piston design requirements. The application of the program to the inlet section, inducer/impeller/stage, bearings, seals, labyrinth, damper, piston, face and corner, and stationary/rotating surfaces is indicated. Design analysis results are reported which show that the balancing piston's designs are adequate and that performance and life will not be degraded by the turbopump's axial load characteristics.

Energy Futures Synthesis for West-Wide Section 368 Energy Corridors

DOE Office of Scientific and Technical Information (OSTI.GOV)

O'Neill, Barbara L.; Gagne, Douglas A.; Cook, Jeffrey J.

To comply with Section 368(a) of the Energy Policy Act of 2005 (EPAct), the U.S. Bureau of Land Management (BLM) and the U.S. Forest Service designated 6,000 miles of energy corridors on public and national forest lands in the western United States in 2009. The corridors, commonly referred to as 'West-wide' or 'Section 368' energy corridors, are intended as preferred locations for future siting of electric transmission and distribution lines and for oil, gas, and hydrogen pipelines. In response to a lawsuit filed by several organizations over the corridor designations, the BLM, Forest Service, and the U.S. Department of Energymore » entered into a Settlement Agreement, directing the formation of the Section 368 Interagency Workgroup to periodically review the energy corridors on a regional basis. In conducting the reviews, the Workgroup identifies new, relevant, existing, publicly available information to make recommendations for revisions, deletions, and additions to the Section 368 energy corridors. This report synthesizes information in available contemporary transmission, pipeline, and energy future studies to inform the regional reviews by providing a snapshot of what the western energy and transmission system will look like generally 10-15 years in the future. After an overview of the western grid implications, the analysis narrows to Region 2 and Region 3 of the BLM Section 368 energy corridors and focuses on the implications of potential developments in the oil, natural gas, and electricity markets in Colorado, New Mexico, Utah, and portions of Arizona and Nevada that could inform the current regional review. This analysis will help inform the Workgroup on potential development within existing corridors and the need for new corridors that have not yet been designated.« less

Risk factors for asthma and allergy associated with urban migration: background and methodology of a cross-sectional study in Afro-Ecuadorian school children in Northeastern Ecuador (Esmeraldas-SCAALA Study)

PubMed Central

Cooper, Philip J; Chico, Martha E; Vaca, Maritza G; Rodriguez, Alejandro; Alcântara-Neves, Neuza M; Genser, Bernd; de Carvalho, Lain Pontes; Stein, Renato T; Cruz, Alvaro A; Rodrigues, Laura C; Barreto, Mauricio L

2006-01-01

Background Asthma and allergic diseases are becoming increasingly frequent in children in urban centres of Latin America although the prevalence of allergic disease is still low in rural areas. Understanding better why the prevalence of asthma is greater in urban migrant populations and the role of risk factors such as life style and environmental exposures, may be key to understand what is behind this trend. Methods/design The Esmeraldas-SCAALA (Social Changes, Asthma and Allergy in Latin America) study consists of cross-sectional and nested case-control studies of school children in rural and urban areas of Esmeraldas Province in Ecuador. The cross-sectional study will investigate risk factors for atopy and allergic disease in rural and migrant urban Afro-Ecuadorian school children and the nested case-control study will examine environmental, biologic and social risk factors for asthma among asthma cases and non-asthmatic controls from the cross-sectional study. Data will be collected through standardised questionnaires, skin prick testing to relevant aeroallergen extracts, stool examinations for parasites, blood sampling (for measurement of IgE, interleukins and other immunological parameters), anthropometric measurements for assessment of nutritional status, exercise testing for assessment of exercise-induced bronchospasm and dust sampling for measurement of household endotoxin and allergen levels. Discussion The information will be used to identify the factors associated with an increased risk of asthma and allergies in migrant and urbanizing populations, to improve the understanding of the causes of the increase in asthma prevalence and to identify potentially modifiable factors to inform the design of prevention programmes to reduce the risk of allergy in urban populations in Latin America. PMID:16970809

Assessing the first wave of epidemiological studies of nanomaterial workers

NASA Astrophysics Data System (ADS)

Liou, Saou-Hsing; Tsai, Candace S. J.; Pelclova, Daniela; Schubauer-Berigan, Mary K.; Schulte, Paul A.

2015-10-01

The results of early animal studies of engineered nanomaterials (ENMs) and air pollution epidemiology suggest that it is important to assess the health of ENM workers. Initial epidemiological studies of workers' exposure to ENMs (<100 nm) are reviewed and characterized for their study designs, findings, and limitations. Of the 15 studies, 11 were cross-sectional, 4 were longitudinal (1 was both cross-sectional and longitudinal in design), and 1 was a descriptive pilot study. Generally, the studies used biologic markers as the dependent variables. All 11 cross-sectional studies showed a positive relationship between various biomarkers and ENM exposures. Three of the four longitudinal studies showed a negative relationship; the fourth showed positive findings after a 1-year follow-up. Each study considered exposure to ENMs as the independent variable. Exposure was assessed by mass concentration in 10 studies and by particle count in six studies. Six of them assessed both mass and particle concentrations. Some of the studies had limited exposure data because of inadequate exposure assessment. Generally, exposure levels were not very high in comparison to those in human inhalation chamber studies, but there were some exceptions. Most studies involved a small sample size, from 2 to 258 exposed workers. These studies represent the first wave of epidemiological studies of ENM workers. They are limited by small numbers of participants, inconsistent (and in some cases inadequate) exposure assessments, generally low exposures, and short intervals between exposure and effect. Still, these studies are a foundation for future work; they provide insight into where ENM workers are experiencing potentially adverse effects that might be related to ENM exposures.

Forest Community: An Ecological Study

ERIC Educational Resources Information Center

Zipko, Stephen J.

1974-01-01

Discusses science activities designed to examine a balanced community in an unspoiled wooded section, including the study of physical and floral characteristics, shrubs, small and large trees, and animals. Indicates that the students' awareness of man's place in nature and nature's place in man is enhanced through such activities. (CC)

Antecedents of Emotional Intelligence: An Empirical Study

ERIC Educational Resources Information Center

Barbuto, John E., Jr.; Story, Joana S.

2010-01-01

This study examined the relationships between emotional intelligence, locus of control, and mental boundaries. Three hundred and eighty-two county employees were sampled using a cross-sectional survey design. The results indicated internal locus of control and thin mental boundaries are positively related to emotional intelligence. A hierarchical…

21 CFR 58.31 - Testing facility management.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 1 2010-04-01 2010-04-01 false Testing facility management. 58.31 Section 58.31... management. For each nonclinical laboratory study, testing facility management shall: (a) Designate a study... appropriately tested for identity, strength, purity, stability, and uniformity, as applicable. (e) Assure that...

Design data book phase A/B study for a pressure fed engine on a reusable space shuttle booster

NASA Technical Reports Server (NTRS)

1972-01-01

Preliminary engineering definition information is presented for a liquid pressure-fed reusable booster engine. The material is reported in three separate sections which include: (1) program and baseline data, (2) critical trade studies summary, and (3) methodology.

Determinants of Effective Communication among Undergraduate Students

ERIC Educational Resources Information Center

Anvari, Roya; Atiyaye, Dauda Mohammed

2014-01-01

This study aims to investigate the relationship between effective communication and transferring information. In the present correlational study, a cross-sectional research design was employed, and data were collected using a questionnaire-based survey. 46 students were chosen based on random sampling and questionnaires were distributed among…

Knowledge Gaps Exist Among Dentists Regarding Curing Lights and Personal Protection.

PubMed

Wright, Wanda G

2017-09-01

Light curing procedures - performance, knowledge level and safety awareness among dentists. Kopperud SE, Rukke HV, Kopperud HM, Bruzell EM. J Dent 2017;58:67-73. Information not available TYPE OF STUDY/DESIGN: Cross-sectional study. Copyright © 2017 Elsevier Inc. All rights reserved.

Crew interface analysis: Selected articles on space human factors research, 1987 - 1991

NASA Technical Reports Server (NTRS)

Bagian, Tandi (Compiler)

1993-01-01

As part of the Flight Crew Support Division at NASA, the Crew Interface Analysis Section is dedicated to the study of human factors in the manned space program. It assumes a specialized role that focuses on answering operational questions pertaining to NASA's Space Shuttle and Space Station Freedom Programs. One of the section's key contributions is to provide knowledge and information about human capabilities and limitations that promote optimal spacecraft and habitat design and use to enhance crew safety and productivity. The section provides human factors engineering for the ongoing missions as well as proposed missions that aim to put human settlements on the Moon and Mars. Research providing solutions to operational issues is the primary objective of the Crew Interface Analysis Section. The studies represent such subdisciplines as ergonomics, space habitability, man-computer interaction, and remote operator interaction.

Thermal performance of plate fin heat sink cooled by air slot impinging jet with different cross-sectional area

NASA Astrophysics Data System (ADS)

Mesalhy, O. M.; El-Sayed, Mostafa M.

2015-06-01

Flow and heat transfer characteristics of a plate-fin heat sink cooled by a rectangular impinging jet with different cross-sectional area were studied experimentally and numerically. The study concentrated on investigating the effect of jet width, fin numbers, and fin heights on thermal performance. Entropy generation minimization method was used to define the optimum design and operating conditions. It is found that, the jet width that minimizes entropy generation changes with heat sink height and fin numbers.

A Comparison of Vertical and Transverse Sections in the Histological Diagnosis of Alopecia Areata Scalp Biopsy Specimens

PubMed Central

Singh, Kanika; Sharma, Sonal; Singh, Usha Rani; Bhattacharya, Sambit Nath

2016-01-01

Context: Both vertical and transverse sections are used for the diagnosis of alopecia areata. However when a single biopsy is submitted the pathologist has to decide which type is better. Aims: To compare the diagnostic histological features in vertical and transverse sections in alopecia areata scalp biopsy specimens. Settings and Design: Tertiary Care Hospital. Comparative Study. Materials and Methods: A total of 30 patients were enrolled in the study. Two four mm punch biopsy were taken. One was used to take vertical sections and the other for transverse section and histological features of alopecia areata noted in both. Statistical Analysis Used: Chi-square test, percentage. Results: Diagnosis of alopecia areata could be made in 30 (100%) cases in transverse sections and 28 cases (93.3%) in vertical sections. The number of hair follicles available for evaluation was more in the transverse section. Nanogen follicles and miniaturization of follicles were better visualized in the transverse sections. However the catagen and telogen follicles were noted in both vertical and transverse sections but the number and the ratio of anagen and telogen hair follicles could be better assessed in the transverse sections. Presence of peribulbar lymphocytic infiltrate, eosinophils and pigment casts were noted in both transverse and vertical sections. Conclusions: Transverse sections provide a better assessment of the histological features of alopecia areata than vertical sections and thus should be preferred. PMID:27625562

Cesarean sections in Alberta from April 1979 to March 1988.

PubMed Central

Saunders, L D; Flowerdew, G

1991-01-01

OBJECTIVES: To determine (a) trends in the cesarean section rate in Alberta from April 1979 to March 1988, (b) the contribution of different primary indications to the overall increase in the cesarean section rate and (c) trends in the cesarean section rate by residence of the mother. DESIGN: Retrospective study. PARTICIPANTS: Women who gave birth in acute care hospitals in Alberta during the study period. Indications for cesarean section were defined by a hierarchic classification system. Geographic regions were identified according to the mother's residence. MAIN RESULTS: The crude cesarean section rate increased from 13.2 to 17.3 per 100 deliveries between 1979-80 and 1987-88. Previous cesarean section accounted for 54% of the increase, breech presentation for 17%, fetal distress for 17% and dystocia for 10%. The contribution of previous cesarean section was due to the substantial increase in the number of women presenting with a previous cesarean section. The cesarean section rate among women who had previously had the procedure decreased from 96.7% in 1979-80 to 84.6% in 1987-88. The crude cesarean section rates by region varied from 10.3 to 22.3 per 100 deliveries. CONCLUSIONS: Further efforts to reduce the rate of cesarean section among women who have previously undergone the procedure are needed to control the rate of cesarean section in Alberta. Decreasing the rate of primary cesarean section is also an important goal. PMID:2025819

SCHOOLS OF PRESTRESSED CONCRETE. PLANNING, DESIGN AND CONSTRUCTION OF EDUCATIONAL FACILITIES FOR SCHOOLS AND COLLEGES.

ERIC Educational Resources Information Center

LYMAN, ROBERT J.

THE USE OF PRESTRESSED CONCRETE IS EMPHASIZED IN THE AREAS OF SCHOOL PLANNING, DESIGN, AND CONSTRUCTION. THE PLANNING SECTION INCLUDES--(1) ROLES OF ACTIVE PARTIES AND RELATED ORGANIZATIONS, (2) PROCEDURES, AND (3) CONCEPTUAL DATA FOR SITE AND BUILDING. THE DESIGN SECTION CONTAINS--(1) DEVELOPMENT OF CONSTRUCTION SYSTEMS, (2) INTEGRATION OF…

Engineering Technology Programs Courses Guide for Computer Aided Design and Computer Aided Manufacturing.

ERIC Educational Resources Information Center

Georgia Univ., Athens. Div. of Vocational Education.

This guide describes the requirements for courses in computer-aided design and computer-aided manufacturing (CAD/CAM) that are part of engineering technology programs conducted in vocational-technical schools in Georgia. The guide is organized in five sections. The first section provides a rationale for occupations in design and in production,…

40 CFR 63.1426 - Process vent requirements for determining organic HAP concentration, control efficiency, and...

Code of Federal Regulations, 2013 CFR

2013-07-01

... performance test for those control techniques in accordance with paragraph (b)(6) of this section. The design..., immediately preceding the use of the control technique. A design evaluation shall also address other vent... paragraph (f)(1)(i) of this section, the design evaluation shall document the control efficiency and address...

78 FR 68735 - Reduction or Suspension of Safe Harbor Contributions

Federal Register 2010, 2011, 2012, 2013, 2014

2013-11-15

... forth in section 401(k)(3), called the actual deferral percentage (ADP) test, or one of the design-based... design-based safe harbor method under which a CODA is treated as satisfying the ADP test if the... the design-based alternatives in section 401(m)(10), 401(m)(11), or 401(m)(12). The ACP test in...