Aquaculture. Second Edition. Teacher Edition.

ERIC Educational Resources Information Center

Walker, Susan S.; Crummett, Dan

This teacher and student guide for aquaculture contains 15 units of instruction that cover the following topics: (1) introduction to aquaculture; (2) the aquatic environment; (3) fundamental fish biology; (4) marketing; (5) site selection; (6) facility design and layout; (7) water quality management; (8) fish health management; (9) commercial…

Unequal-area, fixed-shape facility layout problems using the firefly algorithm

NASA Astrophysics Data System (ADS)

Ingole, Supriya; Singh, Dinesh

2017-07-01

In manufacturing industries, the facility layout design is a very important task, as it is concerned with the overall manufacturing cost and profit of the industry. The facility layout problem (FLP) is solved by arranging the departments or facilities of known dimensions on the available floor space. The objective of this article is to implement the firefly algorithm (FA) for solving unequal-area, fixed-shape FLPs and optimizing the costs of total material handling and transportation between the facilities. The FA is a nature-inspired algorithm and can be used for combinatorial optimization problems. Benchmark problems from the previous literature are solved using the FA. To check its effectiveness, it is implemented to solve large-sized FLPs. Computational results obtained using the FA show that the algorithm is less time consuming and the total layout costs for FLPs are better than the best results achieved so far.

13. Historic drawing of rocket engine test facility layout, including ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

13. Historic drawing of rocket engine test facility layout, including Buildings 202, 205, 206, and 206A, February 3, 1984. NASA GRC drawing number CF-101539. On file at NASA Glenn Research Center. - Rocket Engine Testing Facility, NASA Glenn Research Center, Cleveland, Cuyahoga County, OH

Design & layout of recreation facilities

Treesearch

Howard R. Orr

1971-01-01

Design and layout of recreation facilities is a problem solving process that must be divorced from the emotionalism that has shrouded outdoor recreation and must deal deliberately with the growing information concerning people and natural resources.

48. Photocopy of Architectural Layout drawing, dated August 6, 1976 ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

48. Photocopy of Architectural Layout drawing, dated August 6, 1976 by Raytheon Company. Original drawing property of United States Air Force, 21" Space Command. AL-2 - PAVE PAWS TECHNICAL FACILITY - OTIS AFB - EQUIPMENT LAYOUT - SECOND FLOOR AND PLATFORM 2A. DRAWING NO. AW35-46-06 - Cape Cod Air Station, Technical Facility-Scanner Building & Power Plant, Massachusetts Military Reservation, Sandwich, Barnstable County, MA

Optical design of the National Ignition Facility main laser and switchyard/target area beam transport systems

NASA Astrophysics Data System (ADS)

Miller, John L.; English, R. Edward, Jr.; Korniski, Ronald J.; Rodgers, J. Michael

1999-07-01

The optical design of the main laser and transport mirror sections of the National Ignition Facility are described. For the main laser the configuration, layout constraints, multiple beam arrangement, pinhole layout and beam paths, clear aperture budget, ray trace models, alignment constraints, lens designs, wavefront performance, and pupil aberrations are discussed. For the transport mirror system the layout, alignment controls and clear aperture budget are described.

Reducing Operating Costs by Optimizing Space in Facilities

DTIC Science & Technology

2012-03-01

Base level 5 engineering units will provide facility floor plans, furniture layouts, and staffing documentation as necessary. One obstacle...due to the quantity and diverse locations. Base level engineering units provided facility floor plans, furniture layouts, and staffing documentation... furniture purchases and placement 5. Follow a quality systematic process in all decisions The per person costs can be better understood with a real

Constructing an optimal facility layout to maximize adjacency as a function of common boundary length

NASA Astrophysics Data System (ADS)

Ghassemi Tari, Farhad; Neghabi, Hossein

2018-03-01

An effective facility layout implies that departments with high flow are laid adjacent. However, in the case of a very narrow boundary length between the neighbouring departments, the adjacency would actually be useless. In traditional layout design methods, a score is generally assigned independent of the department's boundary length. This may result in a layout design with a restricted material flow. This article proposes a new concept of adjacency in which the department pairs are laid adjacent with a wider path. To apply this concept, a shop with unequal rectangular departments is contemplated and a mathematical programming model with the objective of maximizing the sum of the adjacency degrees is proposed. A computational experiment is conducted to demonstrate the efficiency of the layout design. It is demonstrated that the new concept provides a more efficient and a more realistic layout design.

Computer visualizations in engineering applications

NASA Astrophysics Data System (ADS)

Bills, K. C.

The use of computerized simulations of various robotic tasks via IGRIP software is reported. The projects include underwater activities demonstrating clean up of a quarry; time study of methods to store waste drums inside a facility; design walk-through of a new facility; plant layout flyover; and conceptual development and layout of new mechanisms.

Space Fabrication Demonstration System

NASA Technical Reports Server (NTRS)

1977-01-01

Progress in the development of a beam builder to be deployed by space shuttle for assembly of large structures in space is reported. The thermal coating for the structural truss was selected and the detail truss design and analysis completed. Data acquired during verification of the design of the basic 'building block' truss are included as well as design layouts for various fabrication facility subsystems.

Modernizing sports facilities

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dustin, R.

Modernization and renovation of sports facilities challenge the design team to balance a number of requirements: spectator and owner expectations, existing building and site conditions, architectural layouts, code and legislation issues, time constraints and budget issues. System alternatives are evaluated and selected based on the relative priorities of these requirements. These priorities are unique to each project. At Alexander Memorial Coliseum, project schedules, construction funds and facility usage became the priorities. The ACC basketball schedule and arrival of the Centennial Olympics dictated the construction schedule. Initiation and success of the project depended on the commitment of the design team tomore » meet coliseum funding levels established three years ago. Analysis of facility usage and system alternative capabilities drove the design team to select a system that met the project requirements and will maximize the benefits to the owner and spectators for many years to come.« less

Mars mission science operations facilities design

NASA Technical Reports Server (NTRS)

Norris, Jeffrey S.; Wales, Roxana; Powell, Mark W.; Backes, Paul G.; Steinke, Robert C.

2002-01-01

A variety of designs for Mars rover and lander science operations centers are discussed in this paper, beginning with a brief description of the Pathfinder science operations facility and its strengths and limitations. Particular attention is then paid to lessons learned in the design and use of operations facilities for a series of mission-like field tests of the FIDO prototype Mars rover. These lessons are then applied to a proposed science operations facilities design for the 2003 Mars Exploration Rover (MER) mission. Issues discussed include equipment selection, facilities layout, collaborative interfaces, scalability, and dual-purpose environments. The paper concludes with a discussion of advanced concepts for future mission operations centers, including collaborative immersive interfaces and distributed operations. This paper's intended audience includes operations facility and situation room designers and the users of these environments.

Simulation Modeling of a Facility Layout in Operations Management Classes

ERIC Educational Resources Information Center

Yazici, Hulya Julie

2006-01-01

Teaching quantitative courses can be challenging. Similarly, layout modeling and lean production concepts can be difficult to grasp in an introductory OM (operations management) class. This article describes a simulation model developed in PROMODEL to facilitate the learning of layout modeling and lean manufacturing. Simulation allows for the…

General layout of reactor and control areas upon advent of ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

General layout of reactor and control areas upon advent of power burst facility (PBF). Shows relationship of PBF to SPERT-I, -II, -III, and -IV. Ebasco Services 1205-PER/PBF-U-102. Date: July 1965. INEEL index no. 761-0100-00-205-123006 - Idaho National Engineering Laboratory, SPERT-I & Power Burst Facility Area, Scoville, Butte County, ID

Layout design in order to improve efficiency in manufacturing

NASA Astrophysics Data System (ADS)

Siregar, I.; Tarigan, U.; Nasution, T. H.

2018-02-01

This research was conducted at the company that produces bobbins and ream type cigarette paper. Problems that found on the production process is the back and forth (back tracking) movement. Back and forth (back tracking) movement extending the total distance moved by the material and increase the total moment of transfer materials thus reducing the efficiency of the transfer of materials in the production process. The purpose of this study is to give design for the layout of production facilities in the company, so that the expected production produced by the company can reach the targets set by the management company. The method used in this research is the Graph-Based Construction and Travel Chart Method. The results of the analysis of the proposed layout with Graph-Based Construction was selected with a total value that is equal to the moment of transfer of 780 758 m / year. This result is better than the actual layout in the amount of 1,021,038.12 meters / year and the results of the method Travel Alternative Chart I of 826.236,60 meters/year, Alternative II of 1.004.433,56 meters / year, and Alternative III for 828,467.12 meters/year. The design layout of Graph-Based Construction material increases the transfer efficiency for 23.53%. With this layout proposal, expected production capacity will be increased along with the shortening of the distance of the displacement that must be passed by the material to be processed.

33 CFR 127.105 - Layout and spacing of marine transfer area for LNG.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 33 Navigation and Navigable Waters 2 2011-07-01 2011-07-01 false Layout and spacing of marine transfer area for LNG. 127.105 Section 127.105 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF... AND LIQUEFIED HAZARDOUS GAS Waterfront Facilities Handling Liquefied Natural Gas § 127.105 Layout and...

33 CFR 127.105 - Layout and spacing of marine transfer area for LNG.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Layout and spacing of marine transfer area for LNG. 127.105 Section 127.105 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF... AND LIQUEFIED HAZARDOUS GAS Waterfront Facilities Handling Liquefied Natural Gas § 127.105 Layout and...

The Use of Multi-Criteria Evaluation and Network Analysis in the Area Development Planning Process

DTIC Science & Technology

2013-03-01

layouts. The alternative layout scoring process, base in multi-criteria evaluation, returns a quantitative score for each alternative layout and a...The purpose of this research was to develop improvements to the area development planning process. These plans are used to improve operations within...an installation sub-section by altering the physical layout of facilities. One methodology was developed based on apply network analysis concepts to

Evidence-based ergonomics. A comparison of Japanese and American office layouts.

PubMed

Noro, Kageyu; Fujimaki, Goroh; Kishi, Shinsuke

2003-01-01

There is a variety of alternatives in office layouts. Yet the theoretical basis and criteria for predicting how well these layouts accommodate employees are poorly understood. The objective of this study was to evaluate criteria for selecting office layouts. Intensive computer workers worked in simulated office layouts in a controlled experimental laboratory. Eye movement measures indicate that knowledge work requires both concentration and interaction. Findings pointed to one layout as providing optimum balance between these 2 requirements. Recommendations for establishing a theoretical basis and design criteria for selecting office layouts based on work style are suggested.

Toward Optimization of Gaze-Controlled Human-Computer Interaction: Application to Hindi Virtual Keyboard for Stroke Patients.

PubMed

Meena, Yogesh Kumar; Cecotti, Hubert; Wong-Lin, Kongfatt; Dutta, Ashish; Prasad, Girijesh

2018-04-01

Virtual keyboard applications and alternative communication devices provide new means of communication to assist disabled people. To date, virtual keyboard optimization schemes based on script-specific information, along with multimodal input access facility, are limited. In this paper, we propose a novel method for optimizing the position of the displayed items for gaze-controlled tree-based menu selection systems by considering a combination of letter frequency and command selection time. The optimized graphical user interface layout has been designed for a Hindi language virtual keyboard based on a menu wherein 10 commands provide access to type 88 different characters, along with additional text editing commands. The system can be controlled in two different modes: eye-tracking alone and eye-tracking with an access soft-switch. Five different keyboard layouts have been presented and evaluated with ten healthy participants. Furthermore, the two best performing keyboard layouts have been evaluated with eye-tracking alone on ten stroke patients. The overall performance analysis demonstrated significantly superior typing performance, high usability (87% SUS score), and low workload (NASA TLX with 17 scores) for the letter frequency and time-based organization with script specific arrangement design. This paper represents the first optimized gaze-controlled Hindi virtual keyboard, which can be extended to other languages.

IC layout adjustment method and tool for improving dielectric reliability at interconnects

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kahng, Andrew B.; Chan, Tuck Boon

Method for adjusting a layout used in making an integrated circuit includes one or more interconnects in the layout that are susceptible to dielectric breakdown are selected. One or more selected interconnects are adjusted to increase via to wire spacing with respect to at least one via and one wire of the one or more selected interconnects. Preferably, the selecting analyzes signal patterns of interconnects, and estimates the stress ratio based on state probability of routed signal nets in the layout. An annotated layout is provided that describes distances by which one or more via or wire segment edges aremore » to be shifted. Adjustments can include thinning and shifting of wire segments, and rotation of vias.« less

The use of multidimensional scaling for facilities layout - An application to the design of the Space Station

NASA Technical Reports Server (NTRS)

Tullis, Thomas S.; Bied Sperling, Barbra; Steinberg, A. L.

1986-01-01

Before an optimum layout of the facilities for the proposed Space Station can be designed, it is necessary to understand the functions that will be performed by the Space Station crew and the relationships among those functions. Five criteria for assessing functional relationships were identified. For each of these criteria, a matrix representing the degree of association of all pairs of functions was developed. The key to making inferences about the layout of the Space Station from these matrices was the use of multidimensional scaling (MDS). Applying MDS to these matrices resulted in spatial configurations of the crew functions in which smaller distances in the MDS configuration reflected closer associations. An MDS analysis of a composite matrix formed by combining the five individual matrices resulted in two dimensions that describe the configuration: a 'private-public' dimension and a 'group-individual' dimension. Seven specific recommendations for Space Station layout were derived from analyses of the MDS configurations. Although these techniques have been applied to the design of the Space Station, they can be applied to the design of any facility where people live or work.

Geologic Materials Center - Policy and Facilities | Alaska Division of

Science.gov Websites

tours are free of charge. Viewing Rooms Public viewing room has five roller tables with 150 linear feet of sample layout space Three private viewing rooms with 25 linear feet of roller table layout space

59. Photocopy of Architectural Layout drawing, dated 25 June, 1993 ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

59. Photocopy of Architectural Layout drawing, dated 25 June, 1993 by US Air Force Space Command. Original drawing property of United States Air Force, 21" Space Command. AL-6 PAVE PAWS SUPPORT SYSTEMS - CAPE COD AFB, MASSACHUSETTS - LAYOUT 4-A, 5TH & 5-A. DRAWING NO. AL-6 - SHEET 7 OF 21. - Cape Cod Air Station, Technical Facility-Scanner Building & Power Plant, Massachusetts Military Reservation, Sandwich, Barnstable County, MA

57. Photocopy of Architectural Layout drawing, dated 25 June, 1993 ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

57. Photocopy of Architectural Layout drawing, dated 25 June, 1993 by US Air Force Space Command. Original drawing property of United States Air Force, 21" Space Command. AL-3 PAVE PAWS SUPPORT SYSTEMS - CAPE COD AFB, MASSACHUSETTS - LAYOUT 1 FLOOR AND 1sr FLOOR ROOF. DRAWING NO. AL-3 - SHEET 4 OF 21. - Cape Cod Air Station, Technical Facility-Scanner Building & Power Plant, Massachusetts Military Reservation, Sandwich, Barnstable County, MA

58. Photocopy of Architectural Layout drawing, dated 25 June, 1993 ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

58. Photocopy of Architectural Layout drawing, dated 25 June, 1993 by US Air Force Space Command. Original drawing property of United States Air Force, 21" Space Command. AL-5 PAVE PAWS SUPPORT SYSTEMS - CAPE COD AFB, MASSACHUSETTS - LAYOUT 3RD, 3A, 4TH LEVELS. DRAWING NO. AL-5 - SHEET 6 OF 21 - Cape Cod Air Station, Technical Facility-Scanner Building & Power Plant, Massachusetts Military Reservation, Sandwich, Barnstable County, MA

44. Photograph of a line drawing. 'PLAN LAYOUT OF PART ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

44. Photograph of a line drawing. 'PLAN LAYOUT OF PART III, SECTION 1, EQUIPMENT LAYOUT, BUILDINGS H-1 TO H-10 INCL., GRINDING, MANUFACTURING AREA, PLANT 'B'.' From U.S. Army Corps of Engineers. Industrial Facilities Inventory, Holston Ordnance Works, Kingsport, Tennessee. Plant 8, Parts II, III. (Nashville, TN: Office of the District Engineer, 1944). - Holston Army Ammunition Plant, RDX-and-Composition-B Manufacturing Line 9, Kingsport, Sullivan County, TN

31. Photograph of a line drawing. 'PLAN LAYOUT OF PART ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

31. Photograph of a line drawing. 'PLAN LAYOUT OF PART III, SECTION 1, EQUIPMENT LAYOUT, BUILDINGS D-1 TO U-10 INCL., NITRATION, MANUFACTURING AREA, PLANT 'B'.' From U.S. Army Corps of Engineers. Industrial Facilities Inventory, Holston Ordnance Works, Kingsport, Tennessee. Plant B, Parts II, III. (Nashville, TN: Office of the District Engineer, 1944). - Holston Army Ammunition Plant, RDX-and-Composition-B Manufacturing Line 9, Kingsport, Sullivan County, TN

Space syntax in healthcare facilities research: a review.

PubMed

Haq, Saif; Luo, Yang

2012-01-01

Space Syntax is a theory and method that has been developing for the last 40 years. Originally conceived as a theory of "society and space," it has expanded to other areas. An important aspect of this is technical; it allows the quantification of layouts, and unit spaces within a layout, so that the environment itself can produce independent variables in quantitative research. Increasingly, it is being used to study healthcare facilities. Space Syntax has thereby become relevant to healthcare facilities researchers and designers. This paper attempts to explain Space Syntax to a new audience of healthcare designers, administrators, and researchers; it provides a literature review on the use of Space Syntax in healthcare facility research and suggests some possibilities for future application.

Implications of system usability on intermodal facility design.

DOT National Transportation Integrated Search

2010-08-01

Ensuring good design of intermodal transportation facilities is critical for effective and : satisfactory operation. Passenger use of the facilities is often hindered by inadequate space, a poor : layout, or lack of signage. This project aims to impr...

10 CFR 70.64 - Requirements for new facilities or new processes at existing facilities.

Code of Federal Regulations, 2011 CFR

2011-01-01

... behavior of items relied on for safety. (b) Facility and system design and facility layout must be based on... existing facilities. (a) Baseline design criteria. Each prospective applicant or licensee shall address the following baseline design criteria in the design of new facilities. Each existing licensee shall address the...

10 CFR 70.64 - Requirements for new facilities or new processes at existing facilities.

Code of Federal Regulations, 2013 CFR

2013-01-01

... behavior of items relied on for safety. (b) Facility and system design and facility layout must be based on... existing facilities. (a) Baseline design criteria. Each prospective applicant or licensee shall address the following baseline design criteria in the design of new facilities. Each existing licensee shall address the...

10 CFR 70.64 - Requirements for new facilities or new processes at existing facilities.

Code of Federal Regulations, 2012 CFR

2012-01-01

... behavior of items relied on for safety. (b) Facility and system design and facility layout must be based on... existing facilities. (a) Baseline design criteria. Each prospective applicant or licensee shall address the following baseline design criteria in the design of new facilities. Each existing licensee shall address the...

10 CFR 70.64 - Requirements for new facilities or new processes at existing facilities.

Code of Federal Regulations, 2014 CFR

2014-01-01

... behavior of items relied on for safety. (b) Facility and system design and facility layout must be based on... existing facilities. (a) Baseline design criteria. Each prospective applicant or licensee shall address the following baseline design criteria in the design of new facilities. Each existing licensee shall address the...

Analysis on flexible manufacturing system layout using arena simulation software

NASA Astrophysics Data System (ADS)

Fadzly, M. K.; Saad, Mohd Sazli; Shayfull, Z.

2017-09-01

Flexible manufacturing system (FMS) was defined as highly automated group technology machine cell, consisting of a group of processing stations interconnected by an automated material handling and storage system, and controlled by an integrated computer system. FMS can produce parts or products are in the mid-volume, mid-variety production range. The layout system in FMS is an important criterion to design the FMS system to produce a part or product. This facility layout of an FMS involves the positioning of cells within given boundaries, so as to minimize the total projected travel time between cells. Defining the layout includes specifying the spatial coordinates of each cell, its orientation in either a horizontal or vertical position, and the location of its load or unloads point. There are many types of FMS layout such as In-line, loop ladder and robot centered cell layout. The research is concentrating on the design and optimization FMS layout. The final conclusion can be summarized that the objective to design and optimisation of FMS layout for this study is successful because the FMS In-line layout is the best layout based on effective time and cost using ARENA simulation software.

14 CFR 151.131 - Forms.

Code of Federal Regulations, 2014 CFR

2014-01-01

... proposal for the development of an airport layout plan or plans, or both, designed to lead to a project... usable airport facility shown on an airport layout plan developed under the proposal, or initiate the... designed to lead to a project application, or both, within three years after the date of acceptance of the...

14 CFR 151.131 - Forms.

Code of Federal Regulations, 2010 CFR

2010-01-01

... proposal for the development of an airport layout plan or plans, or both, designed to lead to a project... usable airport facility shown on an airport layout plan developed under the proposal, or initiate the... designed to lead to a project application, or both, within three years after the date of acceptance of the...

14 CFR 151.131 - Forms.

Code of Federal Regulations, 2012 CFR

2012-01-01

... proposal for the development of an airport layout plan or plans, or both, designed to lead to a project... usable airport facility shown on an airport layout plan developed under the proposal, or initiate the... designed to lead to a project application, or both, within three years after the date of acceptance of the...

14 CFR 151.131 - Forms.

Code of Federal Regulations, 2013 CFR

2013-01-01

... proposal for the development of an airport layout plan or plans, or both, designed to lead to a project... usable airport facility shown on an airport layout plan developed under the proposal, or initiate the... designed to lead to a project application, or both, within three years after the date of acceptance of the...

76 FR 15001 - Entergy Nuclear Operations, Inc,. Entergy Nuclear Vermont Yankee, LLC, Vermont Yankee Nuclear...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-18

... understand VY's design, layout, and construction. This failure to comprehend and understand the layout... Facilities,'' and General Design Criteria 60, ``Control of Releases of Radioactive Materials to the Environment,'' and 64, ``Monitoring Radioactivity Releases,'' of Appendix A, ``General Design Criteria for...

14 CFR 151.131 - Forms.

Code of Federal Regulations, 2011 CFR

2011-01-01

... proposal for the development of an airport layout plan or plans, or both, designed to lead to a project... usable airport facility shown on an airport layout plan developed under the proposal, or initiate the... designed to lead to a project application, or both, within three years after the date of acceptance of the...

Career Development Guide for Services Officers.

DTIC Science & Technology

1986-04-01

1 AirTE Comman and StaffR ColleNI G ....................2 AirtWaru Collge ...feeding operations. This is accomplished by determining personnel requirements and physical layout of facilities. This person also establishes performanco...primarily manages a commissary store. This person * determines personnel and equipment requirements, physical layout, operating *hours, and financial

Layout Improvement Study to Reduce Staff Walking Distance in a Large Health Care Facility: How to Not Walk an Extra 4740 Miles.

PubMed

Ley-Chavez, Adriana; Hmar-Lagroun, Tatiana; Douglas-Ntagha, Pamela; Cumbo, Charlotte L

2016-01-01

Inefficient facility layouts have been found to be a challenge in health care, with excessive walking adding to the demands of staff and creating delays, which can impact the quality of care. Minimizing unnecessary transportation during care delivery improves efficiency, reduces delays, and frees up resources for use on value-added activities. This article presents a methodology and application of facility design to improve responsiveness and efficiency at a large hospital. The approach described provides the opportunity to improve existing layouts in facilities in which the floor plan is already defined, but there is some flexibility to relocate key areas. The existing physical constraints and work flows are studied and taken into consideration, and the volume of traffic flow throughout the facility guides the decision of where to relocate areas for maximum efficiency. Details on the steps followed and general recommendations to perform the necessary process and data analyses are provided. We achieved a 34.8% reduction in distance walked (4740 miles saved per year) and a 30% reduction in floors traveled in elevators (344 931 floors, which translate to 842 hours spent using elevators) by relocating 4 areas in which frequently used resources are housed.

Layout Geometry in the Selection of Intrinsic Frames of Reference from Multiple Viewpoints

ERIC Educational Resources Information Center

Mou, Weimin; Zhao, Mintao; McNamara, Timothy P.

2007-01-01

Four experiments investigated the roles of layout geometry in the selection of intrinsic frames of reference in spatial memory. Participants learned the locations of objects in a room from 2 or 3 viewing perspectives. One view corresponded to the axis of bilateral symmetry of the layout, and the other view(s) was (were) nonorthogonal to the axis…

27. Photograph of a line drawing. 'PLAN LAYOUT AND CROSS ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

27. Photograph of a line drawing. 'PLAN LAYOUT AND CROSS SECTION OF PART III, SECTION 1, EQUIPMENT LAYOUT, BUILDINGS C-1, C-3, C-5, C-6, C-7, C-9 INCL., MIXING, MANUFACTURING AREA, PLANT 'B'.' From the U.S. Army Corps of Engineers. Industrial Facilities Inventory, Holston Ordnance Works, Kingsport, Tennessee. Plant B, Parts II, III. (Nashville, TN: Office of the District Engineer, 1944). - Holston Army Ammunition Plant, RDX-and-Composition-B Manufacturing Line 9, Kingsport, Sullivan County, TN

Design and Simulation Plant Layout Using Systematic Layout Planning

NASA Astrophysics Data System (ADS)

Suhardini, D.; Septiani, W.; Fauziah, S.

2017-12-01

This research aims to design the factory layout of PT. Gunaprima Budiwijaya in order to increase production capacity. The problem faced by this company is inappropriate layout causes cross traffic on the production floor. The re-layout procedure consist of these three steps: analysing the existing layout, designing plant layout based on SLP and evaluation and selection of alternative layout using Simulation Pro model version 6. Systematic layout planning is used to re-layout not based on the initial layout. This SLP produces four layout alternatives, and each alternative will be evaluated based on two criteria, namely cost of material handling using Material Handling Evaluation Sheet (MHES) and processing time by simulation. The results showed that production capacity is increasing as much as 37.5% with the addition of the machine and the operator, while material handling cost was reduced by improvement of the layout. The use of systematic layout planning method reduces material handling cost of 10,98% from initial layout or amounting to Rp1.229.813,34.

The Methodology of Interactive Parametric Modelling of Construction Site Facilities in BIM Environment

NASA Astrophysics Data System (ADS)

Kozlovská, Mária; Čabala, Jozef; Struková, Zuzana

2014-11-01

Information technology is becoming a strong tool in different industries, including construction. The recent trend of buildings designing is leading up to creation of the most comprehensive virtual building model (Building Information Model) in order to solve all the problems relating to the project as early as in the designing phase. Building information modelling is a new way of approaching to the design of building projects documentation. Currently, the building site layout as a part of the building design documents has a very little support in the BIM environment. Recently, the research of designing the construction process conditions has centred on improvement of general practice in planning and on new approaches to construction site layout planning. The state of art in field of designing the construction process conditions indicated an unexplored problem related to connection of knowledge system with construction site facilities (CSF) layout through interactive modelling. The goal of the paper is to present the methodology for execution of 3D construction site facility allocation model (3D CSF-IAM), based on principles of parametric and interactive modelling.

Supporting the design of office layout meeting ergonomics requirements.

PubMed

Margaritis, Spyros; Marmaras, Nicolas

2007-11-01

This paper proposes a method and an information technology tool aiming to support the ergonomics layout design of individual workstations in a given space (building). The proposed method shares common ideas with previous generic methods for office layout. However, it goes a step forward and focuses on the cognitive tasks which have to be carried out by the designer or the design team trying to alleviate them. This is achieved in two ways: (i) by decomposing the layout design problem to six main stages, during which only a limited number of variables and requirements are considered and (ii) by converting the ergonomics requirements to functional design guidelines. The information technology tool (ErgoOffice 0.1) automates certain phases of the layout design process, and supports the design team either by its editing and graphical facilities or by providing adequate memory support.

Designing Clinical Space for the Delivery of Integrated Behavioral Health and Primary Care.

PubMed

Gunn, Rose; Davis, Melinda M; Hall, Jennifer; Heintzman, John; Muench, John; Smeds, Brianna; Miller, Benjamin F; Miller, William L; Gilchrist, Emma; Brown Levey, Shandra; Brown, Jacqueline; Wise Romero, Pam; Cohen, Deborah J

2015-01-01

This study sought to describe features of the physical space in which practices integrating primary care and behavioral health care work and to identify the arrangements that enable integration of care. We conducted an observational study of 19 diverse practices located across the United States. Practice-level data included field notes from 2-4-day site visits, transcripts from semistructured interviews with clinicians and clinical staff, online implementation diary posts, and facility photographs. A multidisciplinary team used a 4-stage, systematic approach to analyze data and identify how physical layout enabled the work of integrated care teams. Two dominant spatial layouts emerged across practices: type-1 layouts were characterized by having primary care clinicians (PCCs) and behavioral health clinicians (BHCs) located in separate work areas, and type-2 layouts had BHCs and PCCs sharing work space. We describe these layouts and the influence they have on situational awareness, interprofessional "bumpability," and opportunities for on-the-fly communication. We observed BHCs and PCCs engaging in more face-to-face methods for coordinating integrated care for patients in type 2 layouts (41.5% of observed encounters vs 11.7%; P < .05). We show that practices needed to strike a balance between professional proximity and private work areas to accomplish job tasks. Private workspace was needed for focused work, to see patients, and for consults between clinicians and clinical staff. We describe the ways practices modified and built new space and provide 2 recommended layouts for practices integrating care based on study findings. Physical layout and positioning of professionals' workspace is an important consideration in practices implementing integrated care. Clinicians, researchers, and health-care administrators are encouraged to consider the role of professional proximity and private working space when creating new facilities or redesigning existing space to foster delivery of integrated behavioral health and primary care. © Copyright 2015 by the American Board of Family Medicine.

How work context affects operating room processes: using data mining and computer simulation to analyze facility and process design.

PubMed

Baumgart, André; Denz, Christof; Bender, Hans-Joachim; Schleppers, Alexander

2009-01-01

The complexity of the operating room (OR) requires that both structural (eg, department layout) and behavioral (eg, staff interactions) patterns of work be considered when developing quality improvement strategies. In our study, we investigated how these contextual factors influence outpatient OR processes and the quality of care delivered. The study setting was a German university-affiliated hospital performing approximately 6000 outpatient surgeries annually. During the 3-year-study period, the hospital significantly changed its outpatient OR facility layout from a decentralized (ie, ORs in adjacent areas of the building) to a centralized (ie, ORs in immediate vicinity of each other) design. To study the impact of the facility change on OR processes, we used a mixed methods approach, including process analysis, process modeling, and social network analysis of staff interactions. The change in facility layout was seen to influence OR processes in ways that could substantially affect patient outcomes. For example, we found a potential for more errors during handovers in the new centralized design due to greater interdependency between tasks and staff. Utilization of the mixed methods approach in our analysis, as compared with that of a single assessment method, enabled a deeper understanding of the OR work context and its influence on outpatient OR processes.

Improvement of the user interface of multimedia applications by automatic display layout

NASA Astrophysics Data System (ADS)

Lueders, Peter; Ernst, Rolf

1995-03-01

Multimedia research has mainly focussed on real-time data capturing and display combined with compression, storage and transmission of these data. However, there is another problem considering real-time selecting and arranging a possibly large amount of data from multiple media on the computer screen together with textual and graphical data of regular software. This problem has already been known from complex software systems, such as CASE and hypertest, and will even be aggravated in multimedia systems. The aim of our work is to alleviate the user from the burden of continuously selecting, placing and sizing windows and their contents, but without introducing solutions limited to only few applications. We present an experimental system which controls the computer screen contents and layouts, directed by a user and/or tool provided information filter and prioritization. To be application independent, the screen layout is based on general layout optimization algorithms adapted from the VLSI layout which are controlled by application specific objective functions. In this paper, we discuss the problems of a comprehensible screen layout including the stability of optical information in time, the information filtering, the layout algorithms and the adaptation of the objective function to include a specific application. We give some examples of different standard applications with layout problems ranging from hierarchical graph layout to window layout. The results show that the automatic tool independent display layout will be possible in a real time interactive environment.

Floor vibration evaluations for medical facilities

NASA Astrophysics Data System (ADS)

Himmel, Chad N.

2003-10-01

The structural floor design for new medical facilities is often selected early in the design phase and in renovation projects, the floor structure already exists. Because the floor structure can often have an influence on the location of vibration sensitive medical equipment and facilities, it is becoming necessary to identify the best locations for equipment and facilities early in the design process. Even though specific criteria for vibration-sensitive uses and equipment may not always be available early in the design phase, it should be possible to determine compatible floor structures for planned vibration-sensitive uses by comparing conceptual layouts with generic floor vibration criteria. Relatively simple evaluations of planned uses and generic criteria, combined with on-site vibration and noise measurements early in design phase, can significantly reduce future design problems and expense. Concepts of evaluation procedures and analyses will be presented in this paper. Generic floor vibration criteria and appropriate parameters to control resonant floor vibration and noise will be discussed for typical medical facilities and medical research facilities. Physical, economic, and logistical limitations that affect implementation will be discussed through case studies.

Science Facilities Bibliography.

ERIC Educational Resources Information Center

National Science Foundation, Washington, DC.

A bibliographic collection on science buildings and facilities is cited with many different reference sources for those concerned with the design, planning, and layout of science facilities. References are given covering a broad scope of information on--(1) physical plant planning, (2) management and safety, (3) building type studies, (4) design…

The accelerator facility of the Heidelberg Ion-Beam Therapy Centre (HIT)

NASA Astrophysics Data System (ADS)

Peters, Andreas

The following sections are included: * Introduction * Beam parameters * General layout of the HIT facility * The accelerator chain in detail * Operational aspects of a particle therapy facility * 24/7 accelerator operation at 335 days per year * Safety and regulatory aspects * Status and perspectives * References

CONCEPTUAL DESIGN ASSESSMENT FOR THE CO-FIRING OF BIO-REFINERY SUPPLIED LIGNIN PROJECT

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ted Berglund; Jeffrey T. Ranney; Carol L. Babb

2001-04-01

The major aspects of this project are proceeding toward completion. Prior to this quarter, design criteria, tentative site selection, facility layout, and preliminary facility cost estimates have been completed and issued for review. Processing of bio-solids was completed, providing material for the pilot operations. Pilot facility design, equipment selection, and modification were completed during the fourth quarter of 2000. Initial pilot facility shakedown was completed during the fourth quarter. After some unavoidable delays, a suitable representative supply of municipal solid waste (MSW) feed material was procured. During this quarter (first quarter of 2001), shredding of the feed material was completedmore » and final feed conditioning was completed. Pilot facility hydrolysis production was completed to produce lignin for co-fire testing. Pilot facility modifications continued to improve facility operations and performance during the first quarter of 2001. Samples of the co-fire fuel material were sent to the co-fire facility for evaluation. The TVA-Colbert facility has neared completion of the task to evaluate the co-location of the Masada facility on the operation of the power generation facility. The TVA-Colbert fossil plant is fully capable of providing a reliable steam supply. The preferred steam supply connection points and steam pipeline routing have been identified. The environmental review of the pipeline routing has been completed and no major impacts have been identified. Detailed assessment of steam export impacts on the Colbert boiler system have been completed and a cost estimate for steam supply system is being developed.« less

Layout of bunch compressor for Beijing XFEL test facility

NASA Astrophysics Data System (ADS)

Zhu, Xiongwei; Du, Yingchao; He, Xiaozhong; Yang, Yufeng

2006-10-01

In this paper, we describe the layout of the bunch compressor for the Beijing XFEL test facility (BTF). Our bunch compressor setup is different from the usual one due to the space limit. The compensation X-BAND cavity and the first bunch compressor are separate in distance. The electron bunch is decelerated first and then accelerated to enter the first bunch compressor. The simulation result shows that our setup works well, and the nonlinear term is well compensated. Also, we present the result about the CSR emittance dilution study. Finally, we develop a program to study microbunch instability in the second BTF bunch compressor.

What Would a Graph Look Like in this Layout? A Machine Learning Approach to Large Graph Visualization.

PubMed

Kwon, Oh-Hyun; Crnovrsanin, Tarik; Ma, Kwan-Liu

2018-01-01

Using different methods for laying out a graph can lead to very different visual appearances, with which the viewer perceives different information. Selecting a "good" layout method is thus important for visualizing a graph. The selection can be highly subjective and dependent on the given task. A common approach to selecting a good layout is to use aesthetic criteria and visual inspection. However, fully calculating various layouts and their associated aesthetic metrics is computationally expensive. In this paper, we present a machine learning approach to large graph visualization based on computing the topological similarity of graphs using graph kernels. For a given graph, our approach can show what the graph would look like in different layouts and estimate their corresponding aesthetic metrics. An important contribution of our work is the development of a new framework to design graph kernels. Our experimental study shows that our estimation calculation is considerably faster than computing the actual layouts and their aesthetic metrics. Also, our graph kernels outperform the state-of-the-art ones in both time and accuracy. In addition, we conducted a user study to demonstrate that the topological similarity computed with our graph kernel matches perceptual similarity assessed by human users.

Conceptual design assessment for the co-firing of bio-refinery supplied lignin project. Quarterly report, July 1--September 30, 2000

DOE Office of Scientific and Technical Information (OSTI.GOV)

Berglund, T.; Ranney, J.T.; Babb, C.L.

2000-10-01

The initial design criteria of the MSW to ethanol facility have been completed along with preliminary site identification and layouts for the processing facility. These items are the first step in evaluating the feasibility of this co-located facility. Pilot facility design and modification are underway for the production and dewatering of the lignin fuel. Major process equipment identification has been completed and several key unit operations will be accomplished on rental equipment. Equipment not available for rental or at TVA has been ordered and facility modification and shakedown will begin in October. The study of the interface and resulting impactsmore » on the TVA Colbert facility are underway. The TVA Colbert fossil plant is fully capable of providing a reliable steam supply for the proposed Masada waste processing facility. The preferred supply location in the Colbert steam cycle has been identified as have possible steam pipeline routes to the Colbert boundary. Additional analysis is underway to fully predict the impact of the steam supply on Colbert plant performance and to select a final steam pipeline route.« less

Radiography Capabilities for Matter-Radiation Interactions in Extremes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Walstrom, Peter Lowell; Garnett, Robert William; Chapman, Catherine A. B

The Matter-Radiation Interactions in Extremes (MaRIE) experimental facility will be used to discover and design the advanced materials needed to meet 21st century national security and energy security challenges. This new facility will provide the new tools scientists need to develop next-generation materials that will perform predictably and on-demand for currently unattainable lifetimes in extreme environments. The MaRIE facility is based on upgrades to the existing LANSCE 800-MeV proton linac and a new 12-GeV electron linac and associated X-ray FEL to provide simultaneous multiple probe beams, and new experimental areas. In addition to the high-energy photon probe beam, both electronmore » and proton radiography capabilities will be available at the MaRIE facility. Recently, detailed radiography system studies have been performed to develop conceptual layouts of high-magnification electron and proton radiography systems that can meet the experimental requirements for the expected first experiments to be performed at the facility. A description of the radiography systems, their performance requirements, and a proposed facility layout are presented.« less

Description of European Space Agency (ESA) Concept Development for a Mars Sample Receiving Facility (MSRF)

NASA Astrophysics Data System (ADS)

Vrublevskis, J.; Berthoud, L.; Guest, M.; Smith, C.; Bennett, A.; Gaubert, F.; Schroeven-Deceuninck, H.; Duvet, L.; van Winnendael, M.

2018-04-01

This presentation gives an overview of the several studies conducted for the European Space Agency (ESA) since 2007, which progressively developed layouts for a potential implementation of a Mars Sample Receiving Facility (MSRF).

Music Facilities.

ERIC Educational Resources Information Center

Ontario Dept. of Education, Toronto. School Planning and Building Research Section.

The layouts and specifications in this booklet are intended to assist those involved in planning music facilities for elementary and secondary schools. Drawings, room plans, and text illustrate specifications for location; space relationship; combined and separate instrumental and vocal rooms; practice rooms; and auxiliary areas. Particular…

Method and apparatus for managing access to a memory

DOE Office of Scientific and Technical Information (OSTI.GOV)

DeBenedictis, Erik

A method and apparatus for managing access to a memory of a computing system. A controller transforms a plurality of operations that represent a computing job into an operational memory layout that reduces a size of a selected portion of the memory that needs to be accessed to perform the computing job. The controller stores the operational memory layout in a plurality of memory cells within the selected portion of the memory. The controller controls a sequence by which a processor in the computing system accesses the memory to perform the computing job using the operational memory layout. The operationalmore » memory layout reduces an amount of energy consumed by the processor to perform the computing job.« less

Biotechnology Facility (BTF) for ISS

NASA Technical Reports Server (NTRS)

1998-01-01

Engineering mockup shows the general arrangement of the plarned Biotechnology Facility inside an EXPRESS rack aboard the International Space Station. This layout includes a gas supply module (bottom left), control computer and laptop interface (bottom right), two rotating wall vessels (top right), and support systems.

SSC Test Operations Contract Overview

NASA Technical Reports Server (NTRS)

Kleim, Kerry D.

2010-01-01

This slide presentation reviews the Test Operations Contract at the Stennis Space Center (SSC). There are views of the test stands layouts, and closer views of the test stands. There are descriptions of the test stand capabilities, some of the other test complexes, the Cryogenic propellant storage facility, the High Pressure Industrial Water (HPIW) facility, and Fluid Component Processing Facility (FCPF).

40 CFR 264.1 - Purpose, scope and applicability.

Code of Federal Regulations, 2013 CFR

2013-07-01

... owner/operator must design, construct, operate, and maintain a unit within a 100-year floodplain to... procedures must address proper design, construction, maintenance, and operation of remediation waste..., the location of all records within the facility, and the facility layout. In addition, this person...

40 CFR 264.1 - Purpose, scope and applicability.

Code of Federal Regulations, 2012 CFR

2012-07-01

... owner/operator must design, construct, operate, and maintain a unit within a 100-year floodplain to... procedures must address proper design, construction, maintenance, and operation of remediation waste..., the location of all records within the facility, and the facility layout. In addition, this person...

40 CFR 264.1 - Purpose, scope and applicability.

Code of Federal Regulations, 2011 CFR

2011-07-01

... owner/operator must design, construct, operate, and maintain a unit within a 100-year floodplain to... procedures must address proper design, construction, maintenance, and operation of remediation waste..., the location of all records within the facility, and the facility layout. In addition, this person...

Design of a signal conditioner for the Fermilab Magnet Test Facility

DOE Office of Scientific and Technical Information (OSTI.GOV)

Giannelli, Pietro

2012-01-01

This thesis describes the design of a remotely-programmable signal conditioner for the harmonic measurement of accelerator magnets. A 10-channel signal conditioning circuit featuring bucking capabilities was designed from scratch and implemented to the level of the printed circuit board layout. Other system components were chosen from those available on the market. Software design was started with the definition of routine procedures. This thesis is part of an upgrade project for replacing obsolescent automated test equipment belonging to the Fermilab Magnet Test Facility. The design started with a given set of requirements. Using a top-down approach, all the circuits were designedmore » and their expected performances were theoretically predicted and simulated. A limited prototyping phase followed. The printed circuit boards were laid out and routed using a CAD software and focusing the design on maximum electromagnetic interference immunity. An embedded board was selected for controlling and interfacing the signal conditioning circuitry with the instrumentation network. Basic low level routines for hardware access were defined. This work covered the entire design process of the signal conditioner, resulting in a project ready for manufacturing. The expected performances are in line with the requirements and, in the cases where this was not possible, approval of trade-offs was sought and received from the end users. Part I deals with the global structure of the signal conditioner and the subdivision in functional macro-blocks. Part II treats the hardware design phase in detail, covering the analog and digital circuits, the printed circuit layouts, the embedded controller and the power supply selection. Part III deals with the basic hardware-related routines to be implemented in the final software.« less

Instructional Media Center. Educational Facility Series. A Guide to Planning.

ERIC Educational Resources Information Center

Esposito, Nicholas A., Ed.

General recommendations are set forth regarding aesthetics, acoustics, lighting, temperature control, location, and layout of the instructional media center. Consideration is given to spatial relationships, equipment and furnishings, and suggestions are included regarding basic and advance facilities for primary, middle and secondary schools. (FS)

Using Multicriteria Analysis in Issues Concerning Adaptation of Historic Facilities for the Needs of Public Utility Buildings with a Function of a Theatre

NASA Astrophysics Data System (ADS)

Obracaj, Piotr; Fabianowski, Dariusz

2017-10-01

Implementations concerning adaptation of historic facilities for public utility objects are associated with the necessity of solving many complex, often conflicting expectations of future users. This mainly concerns the function that includes construction, technology and aesthetic issues. The list of issues is completed with proper protection of historic values, different in each case. The procedure leading to obtaining the expected solution is a multicriteria procedure, usually difficult to accurately define and requiring designer’s large experience. An innovative approach has been used for the analysis, namely - the modified EA FAHP (Extent Analysis Fuzzy Analytic Hierarchy Process) Chang’s method of a multicriteria analysis for the assessment of complex functional and spatial issues. Selection of optimal spatial form of an adapted historic building intended for the multi-functional public utility facility was analysed. The assumed functional flexibility was determined in the scope of: education, conference, and chamber spectacles, such as drama, concerts, in different stage-audience layouts.

Solving a layout design problem by analytic hierarchy process (AHP) and data envelopment analysis (DEA) approach

NASA Astrophysics Data System (ADS)

Tuzkaya, Umut R.; Eser, Arzum; Argon, Goner

2004-02-01

Today, growing amounts of waste due to fast consumption rate of products started an irreversible environmental pollution and damage. A considerable part of this waste is caused by packaging material. With the realization of this fact, various waste policies have taken important steps. Here we considered a firm, where waste Aluminum constitutes majority of raw materials for this fir0m. In order to achieve a profitable recycling process, plant layout should be well designed. In this study, we propose a two-step approach involving Analytic Hierarchy Process (AHP) and Data Envelopment Analysis (DEA) to solve facility layout design problems. A case example is considered to demonstrate the results achieved.

[Spatial tendency of urban land use in new Yinzhou Town of Ningbo City, Zhejiang Province of East China].

PubMed

Jiang, Wen-Wei; Guo, Hui-Hui; Mei, Yan-Xia

2012-03-01

By adopting gradient analysis combining with the analysis of urban land use degree, this paper studied the spatial layout characteristics of residential and industrial lands in new Yinzhou Town, and explored the location characters of various urban land use by selecting public green land, public facilities, and road as the location advantage factors. Gradient analysis could effectively connect with the spatial layout of urban land use, and quantitatively depict the spatial character of urban land use. In the new town, there was a new urban spatial center mostly within the radius of 2 km, namely, the urban core area had obvious location advantage in the cross-shaft direction urban development. On the south of Yinzhou Avenue, the urban hinterland would be constructed soon. In the future land use of the new town, the focus would be the reasonable vicissitude of industrial land after the adjustment of industrial structure, the high-efficient intensive use of the commercial land restricted by the compulsive condition of urban core area, and the agricultural land protection in the southeastern urban-rural fringe.

Developing a gate-array capability at a research and development laboratory

NASA Astrophysics Data System (ADS)

Balch, J. W.; Current, K. W.; Magnuson, W. G., Jr.; Pocha, M. D.

1983-03-01

Experiences in developing a gate array capability for low volume applications in a research and development (R and D) laboratory are described. By purchasing unfinished wafers and doing the customization steps in-house. Turnaround time was shortened to as little as one week and the direct costs reduced to as low as $5K per design. Designs generally require fast turnaround (a few weeks to a few months) and very low volumes (1 to 25). Design costs must be kept at a minimum. After reviewing available commercial gate array design and fabrication services, it was determined that objectives would best be met by using existing internal integrated circuit fabrication facilities, the COMPUTERVISION interactive graphics layout system, and extensive computational capabilities. The reasons and the approach taken for; selection for a particular gate array wafer, adapting a particular logic simulation program, and how layout aids were enhanced are discussed. Testing of the customized chips is described. The content, schedule, and results of the internal gate array course recently completed are discussed. Finally, problem areas and near term plans are presented.

40 CFR 35.920-3 - Contents of application.

Code of Federal Regulations, 2010 CFR

2010-07-01

... legal description of the property to be acquired, a preliminary layout of the distribution and drainage...) Step 2+3. Combination design and construction of a treatment works. Before the award of a grant or... report (required only if a facility is to be constructed) including facility design data and cost...

40 CFR 35.920-3 - Contents of application.

Code of Federal Regulations, 2011 CFR

2011-07-01

... legal description of the property to be acquired, a preliminary layout of the distribution and drainage...) Step 2+3. Combination design and construction of a treatment works. Before the award of a grant or... report (required only if a facility is to be constructed) including facility design data and cost...

40 CFR 35.920-3 - Contents of application.

Code of Federal Regulations, 2012 CFR

2012-07-01

... legal description of the property to be acquired, a preliminary layout of the distribution and drainage...) Step 2+3. Combination design and construction of a treatment works. Before the award of a grant or... report (required only if a facility is to be constructed) including facility design data and cost...

Figures of Merit for Aeronautics Programs and Addition to NASA LARC Fire Station

NASA Technical Reports Server (NTRS)

Harper, Belinda M.

1995-01-01

This report accounts details of two research projects for the Langley Aerospace Research Summer Scholars (LARSS) program. The first project, with the Office of Mission Assurance, involved subjectively predicting the probable success of two aeronautics programs by means of a tool called a Figure of Merit. The figure of merit bases program success on the quality and reliability of the following factors: parts, complexity of research, quality programs, hazards elimination, and single point failures elimination. The second project, for the Office of Safety and Facilities Assurance, required planning, layouts, and source seeking for an addition to the fire house. Forecasted changes in facility layout necessitate this addition which will serve as housing for the fire fighters.

Improving the Spacelab mass memory unit tape layout with a simulation model

NASA Technical Reports Server (NTRS)

Noneman, S. R.

1984-01-01

A tape drive called the Mass Memory Unit (MMU) stores software used by Spacelab computers. MMU tape motion must be minimized during typical flight operations to avoid a loss of scientific data. A projection of the tape motion is needed for evaluation of candidate tape layouts. A computer simulation of the scheduled and unscheduled MMU tape accesses is developed for this purpose. This simulation permits evaluations of candidate tape layouts by tracking and summarizing tape movements. The factors that affect tape travel are investigated and a heuristic is developed to find a good tape layout. An improved tape layout for Spacelab I is selected after the evaluation of fourteen candidates. The simulation model will provide the ability to determine MMU layouts that substantially decrease the tape travel on future Spacelab flights.

Effects on driving performance of interacting with an in-vehicle music player: a comparison of three interface layout concepts for information presentation.

PubMed

Mitsopoulos-Rubens, Eve; Trotter, Margaret J; Lenné, Michael G

2011-05-01

Interface design is an important factor in assessing the potential effects on safety of interacting with an in-vehicle information system while driving. In the current study, the layout of information on a visual display was manipulated to explore its effect on driving performance in the context of music selection. The comparative effects of an auditory-verbal (cognitive) task were also explored. The driving performance of 30 participants was assessed under both baseline and dual task conditions using the Lane Change Test. Concurrent completion of the music selection task with driving resulted in significant impairment to lateral driving performance (mean lane deviation and percentage of correct lane changes) relative to the baseline, and significantly greater mean lane deviation relative to the combined driving and the cognitive task condition. The magnitude of these effects on driving performance was independent of layout concept, although significant differences in subjective workload estimates and performance on the music selection task across layout concepts highlights that potential uncertainty regarding design use as conveyed through layout concept could be disadvantageous. The implications of these results for interface design and safety are discussed. Copyright © 2010 Elsevier Ltd and The Ergonomics Society. All rights reserved.

Solving a mathematical model integrating unequal-area facilities layout and part scheduling in a cellular manufacturing system by a genetic algorithm.

PubMed

Ebrahimi, Ahmad; Kia, Reza; Komijan, Alireza Rashidi

2016-01-01

In this article, a novel integrated mixed-integer nonlinear programming model is presented for designing a cellular manufacturing system (CMS) considering machine layout and part scheduling problems simultaneously as interrelated decisions. The integrated CMS model is formulated to incorporate several design features including part due date, material handling time, operation sequence, processing time, an intra-cell layout of unequal-area facilities, and part scheduling. The objective function is to minimize makespan, tardiness penalties, and material handling costs of inter-cell and intra-cell movements. Two numerical examples are solved by the Lingo software to illustrate the results obtained by the incorporated features. In order to assess the effects and importance of integration of machine layout and part scheduling in designing a CMS, two approaches, sequentially and concurrent are investigated and the improvement resulted from a concurrent approach is revealed. Also, due to the NP-hardness of the integrated model, an efficient genetic algorithm is designed. As a consequence, computational results of this study indicate that the best solutions found by GA are better than the solutions found by B&B in much less time for both sequential and concurrent approaches. Moreover, the comparisons between the objective function values (OFVs) obtained by sequential and concurrent approaches demonstrate that the OFV improvement is averagely around 17 % by GA and 14 % by B&B.

40. Photocopy of building model photograph, ca., 1974, photographer unknown. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

40. Photocopy of building model photograph, ca., 1974, photographer unknown. Original photograph property of United States Air Force, 21" Space Command. CAPE COD AIR STATION PAVE PAWS FACILITY MODEL - ELEVATION SHOWING FLOOR AND EQUIPMENT LAYOUT. - Cape Cod Air Station, Technical Facility-Scanner Building & Power Plant, Massachusetts Military Reservation, Sandwich, Barnstable County, MA

34 CFR 395.31 - Acquisition and occupation of Federal property.

Code of Federal Regulations, 2014 CFR

2014-07-01

... design for such construction, substantial alteration, or renovation includes a satisfactory site or sites for the location and operation of a vending facility by a blind vendor. In those cases where a design... facility to be operated by a blind vendor prior to the completion of the final space layout of the building...

34 CFR 395.31 - Acquisition and occupation of Federal property.

Code of Federal Regulations, 2011 CFR

2011-07-01

... design for such construction, substantial alteration, or renovation includes a satisfactory site or sites for the location and operation of a vending facility by a blind vendor. In those cases where a design... facility to be operated by a blind vendor prior to the completion of the final space layout of the building...

34 CFR 395.31 - Acquisition and occupation of Federal property.

Code of Federal Regulations, 2012 CFR

2012-07-01

... design for such construction, substantial alteration, or renovation includes a satisfactory site or sites for the location and operation of a vending facility by a blind vendor. In those cases where a design... facility to be operated by a blind vendor prior to the completion of the final space layout of the building...

34 CFR 395.31 - Acquisition and occupation of Federal property.

Code of Federal Regulations, 2013 CFR

2013-07-01

... design for such construction, substantial alteration, or renovation includes a satisfactory site or sites for the location and operation of a vending facility by a blind vendor. In those cases where a design... facility to be operated by a blind vendor prior to the completion of the final space layout of the building...

Analytical Tools for Functional Assessment of Architectural Layouts

NASA Astrophysics Data System (ADS)

Bąkowski, Jarosław

2017-10-01

Functional layout of the building, understood as a layout or set of the facility rooms (or groups of rooms) with a system of internal communication, creates an environment and a place of mutual relations between the occupants of the object. Achieving optimal (from the occupants’ point of view) spatial arrangement is possible through activities that often go beyond the stage of architectural design. Adopted in the architectural design, most often during trial and error process or on the basis of previous experience (evidence-based design), functional layout is subject to continuous evaluation and dynamic changing since the beginning of its use. Such verification of the occupancy phase allows to plan future, possible transformations, as well as to develop model solutions for use in other settings. In broader terms, the research hypothesis is to examine whether and how the collected datasets concerning the facility and its utilization can be used to develop methods for assessing functional layout of buildings. In other words, if it is possible to develop an objective method of assessing functional layouts basing on a set of buildings’ parameters: technical, technological and functional ones and whether the method allows developing a set of tools enhancing the design methodology of complex functional objects. By linking the design with the construction phase it is possible to build parametric models of functional layouts, especially in the context of sustainable design or lean design in every aspect: ecological (by reducing the property’s impact on environment), economic (by optimizing its cost) and social (through the implementation of high-performance work environment). Parameterization of size and functional connections of the facility become part of the analyses, as well as the element of model solutions. The “lean” approach means the process of analysis of the existing scheme and consequently - finding weak points as well as means for eliminating these defects. This approach, supplemented by the method of reverse engineering means that already in the design phase there is essential knowledge about the functioning of the facility. It is far beyond intuitive knowledge, based on the standards and specifications. In the scope of reverse engineering methods, the subject of the research is an audit of the product (i.e. architectural design, especially the built spatial layout) in order to determine exactly how it works. Information gained in this way is to help building a system for supporting decisions for preparing design solutions for future investments as well as the functional analysis itself becomes an essential part of the setting up building information process. The data are presented with graphical methods as networks of different factors between rooms. The direct analytical method for the setting is to determine the functional collision between users’ tracks, finding or indication of the shortest paths connecting analyzed rooms and finally to identify the optimal location of these rooms (each according to different factor). The measurement data are supplemented by the results of surveys conducted among users of hospitals, statistics and quantitative medical procedures performed in the test section of the hospital. The results of research are transferred and integrated with BIM system (building information modelling system), and included in the specifications of the IFC (Industry Foundation Classes), especially at the level of information on the relationship between the individual properties associated with elements (in the case of hospitals it may be information about the necessary connections with other rooms, access times from or to specific rooms, rooms utilization conditions, fire safety protection and conditions and many other). At the level of the BIM specification the model data are integrated at the BIM 6D (an extension of the model data with a range of functional analysis) or even BIM 7D (additional integration with systems used at the stage of operation and maintenance of the facility).

LPT. Plot plan and site layout. Includes shield test pool/EBOR ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

LPT. Plot plan and site layout. Includes shield test pool/EBOR facility. (TAN-645 and -646) low power test building (TAN-640 and -641), water storage tanks, guard house (TAN-642), pump house (TAN-644), driveways, well, chlorination building (TAN-643), septic system. Ralph M. Parsons 1229-12 ANP/GE-7-102. November 1956. Approved by INEEL Classification Office for public release. INEEL index code no. 038-0102-00-693-107261 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

10. Photographic copy of engineering drawing showing the plumbing layout ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

10. Photographic copy of engineering drawing showing the plumbing layout of Test Stand 'C' Cv Cell, vacuum line, and scrubber-condenser as erected in 1977-78. JPL drawing by VTN Consolidated, Inc. Engineers, Architects, Planners, 2301 Campus Drive, Irvine, California 92664: 'JPL-ETS E-18 (C-Stand Modifications) Flow Diagram,' sheet M-2 (JPL sheet number E18/41-0), September 1, 1977. - Jet Propulsion Laboratory Edwards Facility, Test Stand C, Edwards Air Force Base, Boron, Kern County, CA

26. Photograph of a line drawing. 'PLAN LAYOUT AND CROSS ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

26. Photograph of a line drawing. 'PLAN LAYOUT AND CROSS SECTION OF PART I, SECTION 8, BUILDINGS NO. C-1, C-3, C-5, C-6, C-7, C-9, MIXING, MANUFACTURING AREA, PLANT B AS OF 4-24-44.' From the U.S. Army Corps of Engineers. Industrial Facilities Inventory, Holston Ordnance Works, Kingsport, Tennessee. Plant B, Parts II, III. (Nashville, TN: Office of the District Engineer, 1944). - Holston Army Ammunition Plant, RDX-and-Composition-B Manufacturing Line 9, Kingsport, Sullivan County, TN

9. Photographic copy of engineering drawing showing the mechanical layout ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

9. Photographic copy of engineering drawing showing the mechanical layout of Test Stand 'C' Cv Cell, vacuum line, and scrubber-condenser as erected in 1977-78. JPL drawing by VTN Consolidated, Inc. Engineers, Architects, Planners, 2301 Campus Drive, Irvine, California 92664: 'JPL-ETS E-18 (C-Stand Modifications) Control Elevations & Schematics,' sheet M-5 (JPL sheet number E18/44-0), 1 September 1977. - Jet Propulsion Laboratory Edwards Facility, Test Stand C, Edwards Air Force Base, Boron, Kern County, CA

Production facility layout by comparing moment displacement using BLOCPLAN and ALDEP Algorithms

NASA Astrophysics Data System (ADS)

Tambunan, M.; Ginting, E.; Sari, R. M.

2018-02-01

Production floor layout settings include the organizing of machinery, materials, and all the equipments used in the production process in the available area. PT. XYZ is a company that manufactures rubber and rubber compounds for retreading tire threaded with hot and cold cooking system. In the production of PT. XYZ is divided into three interrelated parts, namely Masterbatch Department, Department Compound, and Procured Thread Line Department. PT. XYZ has a production process with material flow is irregular and the arrangement of machine is complicated and need to be redesigned. The purpose of this study is comparing movement displacement using BLOCPLAN and ALDEP algorithm in order to redesign existing layout. Redesigning the layout of the production floor is done by applying algorithms of BLOCPLAN and ALDEP. The algorithm used to find the best layout design by comparing the moment displacement and the flow pattern. Moment displacement on the floor layout of the company’s production currently amounts to 2,090,578.5 meters per year and material flow pattern is irregular. Based on the calculation, the moment displacement for the BLOCPLAN is 1,551,344.82 meter per year and ALDEP is 1,600,179 meter per year. Flow Material resulted is in the form of straight the line.

Layout compliance for triple patterning lithography: an iterative approach

NASA Astrophysics Data System (ADS)

Yu, Bei; Garreton, Gilda; Pan, David Z.

2014-10-01

As the semiconductor process further scales down, the industry encounters many lithography-related issues. In the 14nm logic node and beyond, triple patterning lithography (TPL) is one of the most promising techniques for Metal1 layer and possibly Via0 layer. As one of the most challenging problems in TPL, recently layout decomposition efforts have received more attention from both industry and academia. Ideally the decomposer should point out locations in the layout that are not triple patterning decomposable and therefore manual intervention by designers is required. A traditional decomposition flow would be an iterative process, where each iteration consists of an automatic layout decomposition step and manual layout modification task. However, due to the NP-hardness of triple patterning layout decomposition, automatic full chip level layout decomposition requires long computational time and therefore design closure issues continue to linger around in the traditional flow. Challenged by this issue, we present a novel incremental layout decomposition framework to facilitate accelerated iterative decomposition. In the first iteration, our decomposer not only points out all conflicts, but also provides the suggestions to fix them. After the layout modification, instead of solving the full chip problem from scratch, our decomposer can provide a quick solution for a selected portion of layout. We believe this framework is efficient, in terms of performance and designer friendly.

75 FR 42820 - Notice of Availability of a Final Environmental Assessment (Final EA) and a Finding of No...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-07-22

... evaluated the construction and operation of a new 20,000-square-foot standard design Terminal Radar Approach Control Facility/Base Building conforming to the guidelines of the Terminal Facilities Design Standards... Airport Layout Plan. The Final EA has been prepared in accordance with the National Environmental Policy...

48 CFR 552.270-14 - Changes.

Code of Federal Regulations, 2012 CFR

2012-10-01

... following: (1) Specifications (including drawings and designs). (2) Work or services. (3) Facilities or space layout. (4) Amount of space, provided the Lessor consents to the change. (b) If any such change...

48 CFR 552.270-14 - Changes.

Code of Federal Regulations, 2013 CFR

2013-10-01

... following: (1) Specifications (including drawings and designs). (2) Work or services. (3) Facilities or space layout. (4) Amount of space, provided the Lessor consents to the change. (b) If any such change...

48 CFR 552.270-14 - Changes.

Code of Federal Regulations, 2010 CFR

2010-10-01

... following: (1) Specifications (including drawings and designs). (2) Work or services. (3) Facilities or space layout. (4) Amount of space, provided the Lessor consents to the change. (b) If any such change...

48 CFR 552.270-14 - Changes.

Code of Federal Regulations, 2014 CFR

2014-10-01

... following: (1) Specifications (including drawings and designs). (2) Work or services. (3) Facilities or space layout. (4) Amount of space, provided the Lessor consents to the change. (b) If any such change...

Research Possibilities Beyond Deep Space Gateway

NASA Astrophysics Data System (ADS)

Smitherman, D. V.; Needham, D. H.; Lewis, R.

2018-02-01

This abstract explores the possibilities for a large research facilities module attached to the Deep Space Gateway, using the same large module design and basic layout planned for the Deep Space Transport.

48 CFR 552.270-14 - Changes.

Code of Federal Regulations, 2011 CFR

2011-10-01

... following: (1) Specifications (including drawings and designs). (2) Work or services. (3) Facilities or space layout. (4) Amount of space, provided the Lessor consents to the change. (b) If any such change...

A similarity score-based two-phase heuristic approach to solve the dynamic cellular facility layout for manufacturing systems

NASA Astrophysics Data System (ADS)

Kumar, Ravi; Singh, Surya Prakash

2017-11-01

The dynamic cellular facility layout problem (DCFLP) is a well-known NP-hard problem. It has been estimated that the efficient design of DCFLP reduces the manufacturing cost of products by maintaining the minimum material flow among all machines in all cells, as the material flow contributes around 10-30% of the total product cost. However, being NP hard, solving the DCFLP optimally is very difficult in reasonable time. Therefore, this article proposes a novel similarity score-based two-phase heuristic approach to solve the DCFLP optimally considering multiple products in multiple times to be manufactured in the manufacturing layout. In the first phase of the proposed heuristic, a machine-cell cluster is created based on similarity scores between machines. This is provided as an input to the second phase to minimize inter/intracell material handling costs and rearrangement costs over the entire planning period. The solution methodology of the proposed approach is demonstrated. To show the efficiency of the two-phase heuristic approach, 21 instances are generated and solved using the optimization software package LINGO. The results show that the proposed approach can optimally solve the DCFLP in reasonable time.

CONCEPTUAL DESIGN ASSESSMENT FOR THE CO-FIRING OF BIO-REFINERY SUPPLIED LIGNIN PROJECT

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ted Berglund; Jeffrey T. Ranney; Carol L. Babb

2001-01-01

The major aspects of this project are proceeding toward completion. Prior to this quarter, design criteria, tentative site selection, facility layout, and preliminary facility cost estimates have been completed and issued for review. Processing of bio-solids was completed, providing material for the pilot operations. Pilot facility design, equipment selection, and modification were completed during the fourth quarter. Initial pilot facility shakedown was completed during the fourth quarter. During pilot plant shakedown operations, several production batch test runs were performed. These pilot tests were coupled with laboratory testing to confirm pilot results. In initial batches of operations, cellulose to glucose conversionsmore » of 62.5% and 64.8% were observed in laboratory hydrolysis. As part of this testing, lignin dewatering was tested using laboratory and vendor-supplied filtration equipment. Dewatering tests reported moisture contents in the lignin of between 50% and 60%. Dewatering parameters and options will continue to be investigated during lignin production. After some unavoidable delays, a suitable representative supply of MSW feed material was procured. Shredding of the feed material was completed and final drying of the feed is expected to be completed by late January. Once feed drying is completed, pilot facility production will begin to produce lignin for co-fire testing. Facility modifications are expected to continue to improve facility operations and performance during the first quarter of 2001. The TVA-Colbert facility continues to make progress in evaluating the co-location of the Masada facility on the operation of the power generation facility. The TVA-Colbert fossil plant is fully capable of providing a reliable steam supply. The preferred steam supply connection points and steam pipeline routing have been identified. The environmental review of the pipeline routing has been completed and no major impacts have been identified. Detailed assessment of steam export impacts on the Colbert boiler system continues.« less

23 CFR 771.111 - Early coordination, public involvement, and project development.

Code of Federal Regulations, 2012 CFR

2012-04-01

..., substantially changes the layout or functions of connecting roadways or of the facility being improved, has a... planning, (B) The project's alternatives, and major design features, (C) The social, economic...

10 CFR 75.10 - Facility information.

Code of Federal Regulations, 2011 CFR

2011-01-01

..., to the extent feasible, to the form, location and flow of nuclear material, and to the general layout... paragraph (b)(5) of this section, must be prepared on IAEA approved Design Information Questionnaire forms...

10 CFR 75.10 - Facility information.

Code of Federal Regulations, 2014 CFR

2014-01-01

..., to the extent feasible, to the form, location and flow of nuclear material, and to the general layout... paragraph (b)(5) of this section, must be prepared on IAEA approved Design Information Questionnaire forms...

23 CFR 771.111 - Early coordination, public involvement, and project development.

Code of Federal Regulations, 2010 CFR

2010-04-01

..., substantially changes the layout or functions of connecting roadways or of the facility being improved, has a... planning, (B) The project's alternatives, and major design features, (C) The social, economic...

10 CFR 75.10 - Facility information.

Code of Federal Regulations, 2012 CFR

2012-01-01

..., to the extent feasible, to the form, location and flow of nuclear material, and to the general layout... paragraph (b)(5) of this section, must be prepared on IAEA approved Design Information Questionnaire forms...

10 CFR 75.10 - Facility information.

Code of Federal Regulations, 2013 CFR

2013-01-01

..., to the extent feasible, to the form, location and flow of nuclear material, and to the general layout... paragraph (b)(5) of this section, must be prepared on IAEA approved Design Information Questionnaire forms...

23 CFR 771.111 - Early coordination, public involvement, and project development.

Code of Federal Regulations, 2011 CFR

2011-04-01

..., substantially changes the layout or functions of connecting roadways or of the facility being improved, has a... planning, (B) The project's alternatives, and major design features, (C) The social, economic...

PBF Reactor Building (PER620). Plot plan shows layout, including auxiliary ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

PBF Reactor Building (PER-620). Plot plan shows layout, including auxiliary buildings: Emergency Generator (621), Hose House (622), Cooling Tower Auxiliary (624), Maintenance and Storage Warehouse (625), Gas Cylinder Storage (627), Hose House (628), Cooling Tower (720), Substation (719), and other features. Road connections between PBF Reactor, its control building, and SPERT-I site. Note cable trenches along road to control building. Date: July 1965. Ebasco Services, PER-U-101. INEEL index no. 761-0100-00-205-123005 - Idaho National Engineering Laboratory, SPERT-I & Power Burst Facility Area, Scoville, Butte County, ID

Applications of Modeling and Simulation for Flight Hardware Processing at Kennedy Space Center

NASA Technical Reports Server (NTRS)

Marshall, Jennifer L.

2010-01-01

The Boeing Design Visualization Group (DVG) is responsible for the creation of highly-detailed representations of both on-site facilities and flight hardware using computer-aided design (CAD) software, with a focus on the ground support equipment (GSE) used to process and prepare the hardware for space. Throughout my ten weeks at this center, I have had the opportunity to work on several projects: the modification of the Multi-Payload Processing Facility (MPPF) High Bay, weekly mapping of the Space Station Processing Facility (SSPF) floor layout, kinematics applications for the Orion Command Module (CM) hatches, and the design modification of the Ares I Upper Stage hatch for maintenance purposes. The main goal of each of these projects was to generate an authentic simulation or representation using DELMIA V5 software. This allowed for evaluation of facility layouts, support equipment placement, and greater process understanding once it was used to demonstrate future processes to customers and other partners. As such, I have had the opportunity to contribute to a skilled team working on diverse projects with a central goal of providing essential planning resources for future center operations.

CONCEPTUAL DESIGN ASSESSMENT FOR THE CO-FIRING OF BIO-REFINERY SUPPLIED LIGNIN PROJECT

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ted Berglund; Jeffrey T. Ranney; Carol L. Babb

2001-10-01

The major aspects of this project are proceeding toward completion. Prior to this quarter, design criteria, tentative site selection, facility layout, and preliminary facility cost estimates were completed and issued. Processing of bio-solids was completed, providing material for the pilot operations. Pilot facility design, equipment selection, and modification were completed during the fourth quarter of 2000. Initial pilot facility shakedown was completed. After some unavoidable delays, a suitable representative supply of MSW feed material was procured. During this first quarter of 2001, shredding of the feed material and final feed conditioning were completed. Pilot facility hydrolysis production was completed tomore » produce lignin for co-fire testing and the lignin fuel was washed and dewatered. Both the lignin and bio-solids fuel materials for co-fire testing were sent to the co-fire facility (EERC) for evaluation and co-firing. EERC has received coal typical of the fuel to the TVA-Colbert boilers. This material will be used at EERC as baseline material and for mixing with the bio-fuel for combustion testing. EERC combustion testing of the bio-based fuels is scheduled to begin in October of 2001. The TVA-Colbert facility has neared completion of the task to evaluate co-location of the Masada facility on the operation of the power generation facility. The TVA-Colbert fossil plant is fully capable of providing a reliable steam supply. The preferred steam supply connection points and steam pipeline routing have been identified. The environmental review of the pipeline routing has been completed and no major impacts have been identified. Detailed assessment of steam export impacts on the Colbert boiler system have been completed and a cost estimate for steam supply system was completed. The cost estimate and the output and heat rate impacts will be used to determine a preliminary price for the exported steam.« less

Overview of the Neutron experimental facilities at LANSCE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mocko, Michal

2016-06-30

This presentation gives an overview of the neutron experimental facilities at LANSCE. The layout is mentioned in detail, with a map of the south-side experimental facilities, information on Target-4 and the Lujan Center. Then it goes into detail about neutron sources, specifically continuous versus pulsed. Target 4 is then discussed. In conclusion, we have introduced the south-side experimental facilities in operation at LANSCE. 1L target and Target 4 provide complementary neutron energy spectra. Two spallation neutron sources taken together cover more than 11 orders of magnitude in neutron energy.

32 CFR 223.7 - Procedures-determination of DoD UCNI.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Detection and Security Alarm Systems. (i) Information on the layout or design of security and alarm systems...) Frequency and schedule of DoD SNM inventories. (3) Facility Description. (i) Maps, conceptual design, and...

32 CFR 223.7 - Procedures-determination of DoD UCNI.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Detection and Security Alarm Systems. (i) Information on the layout or design of security and alarm systems...) Frequency and schedule of DoD SNM inventories. (3) Facility Description. (i) Maps, conceptual design, and...

How Does Scale of Implementation Impact the Environmental Sustainability of Wastewater Treatment Integrated with Resource Recovery?

PubMed

Cornejo, Pablo K; Zhang, Qiong; Mihelcic, James R

2016-07-05

Energy and resource consumptions required to treat and transport wastewater have led to efforts to improve the environmental sustainability of wastewater treatment plants (WWTPs). Resource recovery can reduce the environmental impact of these systems; however, limited research has considered how the scale of implementation impacts the sustainability of WWTPs integrated with resource recovery. Accordingly, this research uses life cycle assessment (LCA) to evaluate how the scale of implementation impacts the environmental sustainability of wastewater treatment integrated with water reuse, energy recovery, and nutrient recycling. Three systems were selected: a septic tank with aerobic treatment at the household scale, an advanced water reclamation facility at the community scale, and an advanced water reclamation facility at the city scale. Three sustainability indicators were considered: embodied energy, carbon footprint, and eutrophication potential. This study determined that as with economies of scale, there are benefits to centralization of WWTPs with resource recovery in terms of embodied energy and carbon footprint; however, the community scale was shown to have the lowest eutrophication potential. Additionally, technology selection, nutrient control practices, system layout, and topographical conditions may have a larger impact on environmental sustainability than the implementation scale in some cases.

An optimization tool for satellite equipment layout

NASA Astrophysics Data System (ADS)

Qin, Zheng; Liang, Yan-gang; Zhou, Jian-ping

2018-01-01

Selection of the satellite equipment layout with performance constraints is a complex task which can be viewed as a constrained multi-objective optimization and a multiple criteria decision making problem. The layout design of a satellite cabin involves the process of locating the required equipment in a limited space, thereby satisfying various behavioral constraints of the interior and exterior environments. The layout optimization of satellite cabin in this paper includes the C.G. offset, the moments of inertia and the space debris impact risk of the system, of which the impact risk index is developed to quantify the risk to a satellite cabin of coming into contact with space debris. In this paper an optimization tool for the integration of CAD software as well as the optimization algorithms is presented, which is developed to automatically find solutions for a three-dimensional layout of equipment in satellite. The effectiveness of the tool is also demonstrated by applying to the layout optimization of a satellite platform.

Automatic page composition with nested sub-layouts

NASA Astrophysics Data System (ADS)

Hunter, Andrew

2013-03-01

This paper provides an overview of a system for the automatic composition of publications. The system first composes nested hierarchies of contents, then applies layout engines at branch points in the hierarchies to explore layout options, and finally selects the best overall options for the finished publications. Although the system has been developed as a general platform for automated publishing, this paper describes its application to the composition and layout of a magazine-like publication for social content from Facebook. The composition process works by assembling design fragments that have been populated with text and images from the Facebook social network. The fragments constitute a design language for a publication. Each design fragment is a nested mutable sub-layout that has no specific size or shape until after it has been laid-out. The layout process balances the space requirements of the fragment's internal contents with its external context in the publication. The mutability of sub-layouts requires that their layout options must be kept open until all the other contents that share the same space have been considered. Coping with large numbers of options is one of the greatest challenges in layout automation. Most existing layout methods work by rapidly elimination design options rather than by keeping options open. A further goal of this publishing system is to confirm that a custom publication can be generated quickly by the described methods. In general, the faster that publications can be created, the greater the opportunities for the technology.

The Development of an Information System Master Plan for the Pacific Missile Range Facility, Barking Sands, Hawaii

DTIC Science & Technology

1992-03-01

sites and support facilities are located on the islands of Niihau and Oahu. Figure 1 depicts the overall layout of PMRF. [Ref. 4: p. 2] In addition...the HIANG facility at Kokee: • a wideband microwave system serving Niihau Island remotely controls operation of the AN/APS-134 surveillance radar, and...provides relay of digitized radar data, control data and voice between the remotely operated, unmanned radar on Niihau Island and Barking Sands

Education: University is Nucleus of New Belgian Town

ERIC Educational Resources Information Center

O'Sullivan, Dermot A.

1972-01-01

The description of Louvain-la-Neuve, near Brussels, where the layout of university facilities, the town, and the science park has been conceived and planned as an integrated whole rather than as piecemeal additions. (Author/CP)

Safeguards Approaches for Black Box Processes or Facilities

DOE Office of Scientific and Technical Information (OSTI.GOV)

Diaz-Marcano, Helly; Gitau, Ernest TN; Hockert, John

2013-09-25

The objective of this study is to determine whether a safeguards approach can be developed for “black box” processes or facilities. These are facilities where a State or operator may limit IAEA access to specific processes or portions of a facility; in other cases, the IAEA may be prohibited access to the entire facility. The determination of whether a black box process or facility is safeguardable is dependent upon the details of the process type, design, and layout; the specific limitations on inspector access; and the restrictions placed upon the design information that can be provided to the IAEA. Thismore » analysis identified the necessary conditions for safeguardability of black box processes and facilities.« less

Safety assessment in plant layout design using indexing approach: implementing inherent safety perspective. Part 2-Domino Hazard Index and case study.

PubMed

Tugnoli, Alessandro; Khan, Faisal; Amyotte, Paul; Cozzani, Valerio

2008-12-15

The design of layout plans requires adequate assessment tools for the quantification of safety performance. The general focus of the present work is to introduce an inherent safety perspective at different points of the layout design process. In particular, index approaches for safety assessment and decision-making in the early stages of layout design are developed and discussed in this two-part contribution. Part 1 (accompanying paper) of the current work presents an integrated index approach for safety assessment of early plant layout. In the present paper (Part 2), an index for evaluation of the hazard related to the potential of domino effects is developed. The index considers the actual consequences of possible escalation scenarios and scores or ranks the subsequent accident propagation potential. The effects of inherent and passive protection measures are also assessed. The result is a rapid quantification of domino hazard potential that can provide substantial support for choices in the early stages of layout design. Additionally, a case study concerning selection among various layout options is presented and analyzed. The case study demonstrates the use and applicability of the indices developed in both parts of the current work and highlights the value of introducing inherent safety features early in layout design.

Graph Drawing Aesthetics-Created by Users, Not Algorithms.

PubMed

Purchase, H C; Pilcher, C; Plimmer, B

2012-01-01

Prior empirical work on layout aesthetics for graph drawing algorithms has concentrated on the interpretation of existing graph drawings. We report on experiments which focus on the creation and layout of graph drawings: participants were asked to draw graphs based on adjacency lists, and to lay them out "nicely." Two interaction methods were used for creating the drawings: a sketch interface which allows for easy, natural hand movements, and a formal point-and-click interface similar to a typical graph editing system. We find, in common with many other studies, that removing edge crossings is the most significant aesthetic, but also discover that aligning nodes and edges to an underlying grid is important. We observe that the aesthetics favored by participants during creation of a graph drawing are often not evident in the final product and that the participants did not make a clear distinction between the processes of creation and layout. Our results suggest that graph drawing systems should integrate automatic layout with the user's manual editing process, and provide facilities to support grid-based graph creation.

Selecting a proper design period for heliostat field layout optimization using Campo code

NASA Astrophysics Data System (ADS)

Saghafifar, Mohammad; Gadalla, Mohamed

2016-09-01

In this paper, different approaches are considered to calculate the cosine factor which is utilized in Campo code to expand the heliostat field layout and maximize its annual thermal output. Furthermore, three heliostat fields containing different number of mirrors are taken into consideration. Cosine factor is determined by considering instantaneous and time-average approaches. For instantaneous method, different design days and design hours are selected. For the time average method, daily time average, monthly time average, seasonally time average, and yearly time averaged cosine factor determinations are considered. Results indicate that instantaneous methods are more appropriate for small scale heliostat field optimization. Consequently, it is proposed to consider the design period as the second design variable to ensure the best outcome. For medium and large scale heliostat fields, selecting an appropriate design period is more important. Therefore, it is more reliable to select one of the recommended time average methods to optimize the field layout. Optimum annual weighted efficiency for heliostat fields (small, medium, and large) containing 350, 1460, and 3450 mirrors are 66.14%, 60.87%, and 54.04%, respectively.

Microgravity

NASA Image and Video Library

1998-01-01

Engineering mockup shows the general arrangement of the plarned Biotechnology Facility inside an EXPRESS rack aboard the International Space Station. This layout includes a gas supply module (bottom left), control computer and laptop interface (bottom right), two rotating wall vessels (top right), and support systems.

11 CFR 9033.12 - Production of computerized information.

Code of Federal Regulations, 2010 CFR

2010-01-01

...) Disbursements made and reimbursements received for the cost of transportation, ground services and facilities...'s software capabilities, such as user guides, technical manuals, formats, layouts and other... software and the computerized information prepared or maintained by the committee. ...

An application of corelap algoritm to improve the utilization space of the classroom

NASA Astrophysics Data System (ADS)

Sembiring, A. C.; Budiman, I.; Mardhatillah, A.; Tarigan, U. P.; Jawira, A.

2018-04-01

The high demand of the room due to the increasing number of students requires the addition of the room The limited number of rooms, the price of land and the cost of building expensive infrastructure requires effective and efficient use of the space. The facility layout redesign is done using the Computerized Relationship Planning (CORELAP) algorithm based on total closeness rating (TCR). By calculating the square distance between the departments based on the coordinates of the central point of the department. The distance obtained is multiplied by the material current from the From-to chart matrix. The analysis is done by comparing the total distance between the initial layout and the proposed layout and then viewing the activities performed in each room. The results of CORELAP algorithm processing gives an increase of room usage efficiency equal to 14, 98% from previous activity.

Simultaneous optimization of micro-heliostat geometry and field layout using a genetic algorithm

NASA Astrophysics Data System (ADS)

Lazardjani, Mani Yousefpour; Kronhardt, Valentina; Dikta, Gerhard; Göttsche, Joachim

2016-05-01

A new optimization tool for micro-heliostat (MH) geometry and field layout is presented. The method intends simultaneous performance improvement and cost reduction through iteration of heliostat geometry and field layout parameters. This tool was developed primarily for the optimization of a novel micro-heliostat concept, which was developed at Solar-Institut Jülich (SIJ). However, the underlying approach for the optimization can be used for any heliostat type. During the optimization the performance is calculated using the ray-tracing tool SolCal. The costs of the heliostats are calculated by use of a detailed cost function. A genetic algorithm is used to change heliostat geometry and field layout in an iterative process. Starting from an initial setup, the optimization tool generates several configurations of heliostat geometries and field layouts. For each configuration a cost-performance ratio is calculated. Based on that, the best geometry and field layout can be selected in each optimization step. In order to find the best configuration, this step is repeated until no significant improvement in the results is observed.

Site Planning and Layout.

ERIC Educational Resources Information Center

Moore, Gary T.

1998-01-01

Examines five issues related to child care facility design: (1) siting the building, outdoor play, and service areas; (2) creating favorable microclimates; (3) developmentally appropriate play yards; (4) pedestrian access and site circulation; and (5) vehicular access and parking away from pedestrians and play. (KB)

Yucca Mountain Project Subsurface Facilities Design

DOE Office of Scientific and Technical Information (OSTI.GOV)

A. Linden; R.S. Saunders; R.J. Boutin

2002-11-19

Four units of the Topopah Springs formation (volcanic tuff) are considered for the proposed repository: the upper lithophysal, the middle non-lithophysal, the lower lithophysal, and the lower non-lithophysal. Yucca Mountain was recently designated the site for a proposed repository to dispose of spent nuclear fuel and high-level radioactive waste. Work is proceeding to advance the design of subsurface facilities to accommodate emplacing waste packages in the proposed repository. This paper summarized recent progress in the design of subsurface layout of the proposed repository. The original Site Recommendation (SR) concept for the subsurface design located the repository largely within the lowermore » lithophysal zone (approximately 73%) of the Topopah The Site Recommendation characterized area suitable for emplacement consisted of the primary upper block, the lower block and the southern upper block extension. The primary upper block accommodated the mandated 70,000 metric tons of heavy metal (MTHM) at a 1.45 kW/m hear heat load. Based on further study of the Site Recommendation concept, the proposed repository siting area footprint was modified to make maximum use of available site characterization data, and thus, reduce uncertainties associated with performance assessment. As a result of this study, a modified repository footprint has been proposed and is presently being review for acceptance by the DOE. A panel design concept was developed to reduce overall costs and reduce the overall emplacement schedule. This concept provides flexibility to adjust the proposed repository subsurface layout with time, as it makes it unnecessary to ''commit'' to development of a large single panel at the earliest stages of construction. A description of the underground layout configuration and influencing factors that affect the layout configuration are discussed in the report.« less

Development of a Prediction Model Based on RBF Neural Network for Sheet Metal Fixture Locating Layout Design and Optimization.

PubMed

Wang, Zhongqi; Yang, Bo; Kang, Yonggang; Yang, Yuan

2016-01-01

Fixture plays an important part in constraining excessive sheet metal part deformation at machining, assembly, and measuring stages during the whole manufacturing process. However, it is still a difficult and nontrivial task to design and optimize sheet metal fixture locating layout at present because there is always no direct and explicit expression describing sheet metal fixture locating layout and responding deformation. To that end, an RBF neural network prediction model is proposed in this paper to assist design and optimization of sheet metal fixture locating layout. The RBF neural network model is constructed by training data set selected by uniform sampling and finite element simulation analysis. Finally, a case study is conducted to verify the proposed method.

A multiple-drawer medication layout problem in automated dispensing cabinets.

PubMed

Pazour, Jennifer A; Meller, Russell D

2012-12-01

In this paper we investigate the problem of locating medications in automated dispensing cabinets (ADCs) to minimize human selection errors. We formulate the multiple-drawer medication layout problem and show that the problem can be formulated as a quadratic assignment problem. As a way to evaluate various medication layouts, we develop a similarity rating for medication pairs. To solve industry-sized problem instances, we develop a heuristic approach. We use hospital ADC transaction data to conduct a computational experiment to test the performance of our developed heuristics, to demonstrate how our approach can aid in ADC design trade-offs, and to illustrate the potential improvements that can be made when applying an analytical process to the multiple-drawer medication layout problem. Finally, we present conclusions and future research directions.

Development of a Prediction Model Based on RBF Neural Network for Sheet Metal Fixture Locating Layout Design and Optimization

PubMed Central

Wang, Zhongqi; Yang, Bo; Kang, Yonggang; Yang, Yuan

2016-01-01

Fixture plays an important part in constraining excessive sheet metal part deformation at machining, assembly, and measuring stages during the whole manufacturing process. However, it is still a difficult and nontrivial task to design and optimize sheet metal fixture locating layout at present because there is always no direct and explicit expression describing sheet metal fixture locating layout and responding deformation. To that end, an RBF neural network prediction model is proposed in this paper to assist design and optimization of sheet metal fixture locating layout. The RBF neural network model is constructed by training data set selected by uniform sampling and finite element simulation analysis. Finally, a case study is conducted to verify the proposed method. PMID:27127499

The Systems Biology Markup Language (SBML) Level 3 Package: Layout, Version 1 Core.

PubMed

Gauges, Ralph; Rost, Ursula; Sahle, Sven; Wengler, Katja; Bergmann, Frank T

2015-06-01

Many software tools provide facilities for depicting reaction network diagrams in a visual form. Two aspects of such a visual diagram can be distinguished: the layout (i.e.: the positioning and connections) of the elements in the diagram, and the graphical form of the elements (for example, the glyphs used for symbols, the properties of the lines connecting them, and so on). For software tools that also read and write models in SBML (Systems Biology Markup Language) format, a common need is to store the network diagram together with the SBML representation of the model. This in turn raises the question of how to encode the layout and the rendering of these diagrams. The SBML Level 3 Version 1 Core specification does not provide a mechanism for explicitly encoding diagrams, but it does provide a mechanism for SBML packages to extend the Core specification and add additional syntactical constructs. The Layout package for SBML Level 3 adds the necessary features to SBML so that diagram layouts can be encoded in SBML files, and a companion package called SBML Rendering specifies how the graphical rendering of elements can be encoded. The SBML Layout package is based on the principle that reaction network diagrams should be described as representations of entities such as species and reactions (with direct links to the underlying SBML elements), and not as arbitrary drawings or graphs; for this reason, existing languages for the description of vector drawings (such as SVG) or general graphs (such as GraphML) cannot be used.

The Systems Biology Markup Language (SBML) Level 3 Package: Layout, Version 1 Core.

PubMed

Gauges, Ralph; Rost, Ursula; Sahle, Sven; Wengler, Katja; Bergmann, Frank Thomas

2015-09-04

Many software tools provide facilities for depicting reaction network diagrams in a visual form. Two aspects of such a visual diagram can be distinguished: the layout (i.e.: the positioning and connections) of the elements in the diagram, and the graphical form of the elements (for example, the glyphs used for symbols, the properties of the lines connecting them, and so on). For software tools that also read and write models in SBML (Systems Biology Markup Language) format, a common need is to store the network diagram together with the SBML representation of the model. This in turn raises the question of how to encode the layout and the rendering of these diagrams. The SBML Level 3 Version 1 Core specification does not provide a mechanism for explicitly encoding diagrams, but it does provide a mechanism for SBML packages to extend the Core specification and add additional syntactical constructs. The Layout package for SBML Level 3 adds the necessary features to SBML so that diagram layouts can be encoded in SBML files, and a companion package called SBML Rendering specifies how the graphical rendering of elements can be encoded. The SBML Layout package is based on the principle that reaction network diagrams should be described as representations of entities such as species and reactions (with direct links to the underlying SBML elements), and not as arbitrary drawings or graphs; for this reason, existing languages for the description of vector drawings (such as SVG) or general graphs (such as GraphML) cannot be used.

32 CFR Appendix B to Part 223 - Guidelines for the Determination of DoD UCNI

Code of Federal Regulations, 2011 CFR

2011-07-01

... Systems a. Information on the layout or design of security and alarm systems at a specific DoD SNM.... Frequency and schedule of DoD SNM inventories. 3. Facility Description a. Maps, conceptual design, and...

32 CFR Appendix B to Part 223 - Guidelines for the Determination of DoD UCNI

Code of Federal Regulations, 2012 CFR

2012-07-01

... Systems a. Information on the layout or design of security and alarm systems at a specific DoD SNM.... Frequency and schedule of DoD SNM inventories. 3. Facility Description a. Maps, conceptual design, and...

32 CFR Appendix B to Part 223 - Guidelines for the Determination of DoD UCNI

Code of Federal Regulations, 2010 CFR

2010-07-01

... Systems a. Information on the layout or design of security and alarm systems at a specific DoD SNM.... Frequency and schedule of DoD SNM inventories. 3. Facility Description a. Maps, conceptual design, and...

An air-bearing weight offload system for ground test of heavy LSS structures

NASA Technical Reports Server (NTRS)

Rice, R. B.

1989-01-01

The capability and use of the Gravity Offload Facility (GOF) are discussed. Briefly explained are the: truss and base casting; carriage assembly; carriage weldment; vertical lift axis control; lifting cylinder; payload gimbal; motion base layout; and control processor.

Facilities and Methods Used in Full-scale Airplane Crash-fire Investigation

NASA Technical Reports Server (NTRS)

Black, Dugald O.

1952-01-01

The facilities and the techniques employed in the conduct of full scale airplane crash-fire studies currently being conducted at the NACA Lewis laboratory are discussed herein. This investigation is part of a comprehensive study of the airplane crash-fire problem. The crash configuration chosen, the general physical layout of the crash site, the test methods, the instrumentation, the data-recording systems, and the post-crash examination procedure are described

A tight upper bound for quadratic knapsack problems in grid-based wind farm layout optimization

NASA Astrophysics Data System (ADS)

Quan, Ning; Kim, Harrison M.

2018-03-01

The 0-1 quadratic knapsack problem (QKP) in wind farm layout optimization models possible turbine locations as nodes, and power loss due to wake effects between pairs of turbines as edges in a complete graph. The goal is to select up to a certain number of turbine locations such that the sum of selected node and edge coefficients is maximized. Finding the optimal solution to the QKP is difficult in general, but it is possible to obtain a tight upper bound on the QKP's optimal value which facilitates the use of heuristics to solve QKPs by giving a good estimate of the optimality gap of any feasible solution. This article applies an upper bound method that is especially well-suited to QKPs in wind farm layout optimization due to certain features of the formulation that reduce the computational complexity of calculating the upper bound. The usefulness of the upper bound was demonstrated by assessing the performance of the greedy algorithm for solving QKPs in wind farm layout optimization. The results show that the greedy algorithm produces good solutions within 4% of the optimal value for small to medium sized problems considered in this article.

Optimizing longwall mine layouts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Minkel, M.J.

1996-12-31

Before spending the time to design an underground mine in detail, the mining engineer should be assured of the economic viability of the location of the layout. This has historically been a trial-and-error, iterative process. Traditional underground mine planning usually bases the layout on the geological characteristics of a deposit such as minimum seam height, quality, and the absence of faults. Whether one attempts to make a decision manually. or use traditional mine planning software, the process works something like this: First you build geological model. Then you impose a {open_quotes}best guess{close_quotes} as to which geological layers will become partmore » of the mined product, or will influence mining. Next you place your design where you believe is the best location to make a mine. Then you select equipment which you believe will cost-effectively mine the area. Finally, you schedule your equipment selection through the design over the mine life, run financial analyses and see if the rate of return is acceptable. If the NPV is acceptable, the design is accepted. If the NPV is not acceptable, the engineer has to restart the cycle of redesigning the layout, rescheduling the equipment, and restudying the economics again.« less

Design for an integrated discipline operations control center for Space Station Freedom

NASA Technical Reports Server (NTRS)

Haines, Richard F.

1993-01-01

This paper presents selected features of a human factors oriented plan for a Space Station Freedom (SSF) ground Discipline Operations Center (DOC) that is integrated with other work areas used by multidisciplinary life scientists. This combined facility is referred to as an integrated DOC or IDOC. This plan is based upon the assumption that there will be a constantly changing array of specialized equipment and procedures used by life sciences principal investigators (PI) on the ground which must be linked to SSF through various DOC systems. Other sites will also be able to communicate with SSF (Anon., 1992). It is also assumed that cost reduction will be a major design consideration and that one integrated structure will be less expensive to build and operate than two separate ones. Since both the DOC personnel and PIs will need to communicate with the flight crew aboard SSF, the general interconnect architecture of the PIs' communication linkage is considered here. Key human factor design elements of this plan include: a candidate facility layout which accommodates three (3), multipurpose, rapidly reconfigurable work areas (suites) and consequent user traffic flow considerations, a multimedia telecommunications support capability, functional (human) traffic flow, optimized internal illumination and acoustics requirements, selected volumetric and safety requirements, and other architectural design parameters.

Layout pattern analysis using the Voronoi diagram of line segments

NASA Astrophysics Data System (ADS)

Dey, Sandeep Kumar; Cheilaris, Panagiotis; Gabrani, Maria; Papadopoulou, Evanthia

2016-01-01

Early identification of problematic patterns in very large scale integration (VLSI) designs is of great value as the lithographic simulation tools face significant timing challenges. To reduce the processing time, such a tool selects only a fraction of possible patterns which have a probable area of failure, with the risk of missing some problematic patterns. We introduce a fast method to automatically extract patterns based on their structure and context, using the Voronoi diagram of line-segments as derived from the edges of VLSI design shapes. Designers put line segments around the problematic locations in patterns called "gauges," along which the critical distance is measured. The gauge center is the midpoint of a gauge. We first use the Voronoi diagram of VLSI shapes to identify possible problematic locations, represented as gauge centers. Then we use the derived locations to extract windows containing the problematic patterns from the design layout. The problematic locations are prioritized by the shape and proximity information of the design polygons. We perform experiments for pattern selection in a portion of a 22-nm random logic design layout. The design layout had 38,584 design polygons (consisting of 199,946 line segments) on layer Mx, and 7079 markers generated by an optical rule checker (ORC) tool. The optical rules specify requirements for printing circuits with minimum dimension. Markers are the locations of some optical rule violations in the layout. We verify our approach by comparing the coverage of our extracted patterns to the ORC-generated markers. We further derive a similarity measure between patterns and between layouts. The similarity measure helps to identify a set of representative gauges that reduces the number of patterns for analysis.

Using Workflow Diagrams to Address Hand Hygiene in Pediatric Long-Term Care Facilities1

PubMed Central

Carter, Eileen J.; Cohen, Bevin; Murray, Meghan T.; Saiman, Lisa; Larson, Elaine L.

2015-01-01

Hand hygiene (HH) in pediatric long-term care settings has been found to be sub-optimal. Multidisciplinary teams at three pediatric long-term care facilities developed step-by-step workflow diagrams of commonly performed tasks highlighting HH opportunities. Diagrams were validated through observation of tasks and concurrent diagram assessment. Facility teams developed six workflow diagrams that underwent 22 validation observations. Four main themes emerged: 1) diagram specificity, 2) wording and layout, 3) timing of HH indications, and 4) environmental hygiene. The development of workflow diagrams is an opportunity to identify and address the complexity of HH in pediatric long-term care facilities. PMID:25773517

Neutron Scattering Announcements

Science.gov Websites

will be added. We encourage everyone interested in neutron scattering to take full advantage of this neutron source ESS. After an initial layout phase using analytical considerations further assessment of Home Page | Facilities | Reference | Software | Conferences | Announcements | Mailing Lists Neutron

Toward Optimal Target Placement for Neural Prosthetic Devices

PubMed Central

Cunningham, John P.; Yu, Byron M.; Gilja, Vikash; Ryu, Stephen I.; Shenoy, Krishna V.

2008-01-01

Neural prosthetic systems have been designed to estimate continuous reach trajectories (motor prostheses) and to predict discrete reach targets (communication prostheses). In the latter case, reach targets are typically decoded from neural spiking activity during an instructed delay period before the reach begins. Such systems use targets placed in radially symmetric geometries independent of the tuning properties of the neurons available. Here we seek to automate the target placement process and increase decode accuracy in communication prostheses by selecting target locations based on the neural population at hand. Motor prostheses that incorporate intended target information could also benefit from this consideration. We present an optimal target placement algorithm that approximately maximizes decode accuracy with respect to target locations. In simulated neural spiking data fit from two monkeys, the optimal target placement algorithm yielded statistically significant improvements up to 8 and 9% for two and sixteen targets, respectively. For four and eight targets, gains were more modest, as the target layouts found by the algorithm closely resembled the canonical layouts. We trained a monkey in this paradigm and tested the algorithm with experimental neural data to confirm some of the results found in simulation. In all, the algorithm can serve not only to create new target layouts that outperform canonical layouts, but it can also confirm or help select among multiple canonical layouts. The optimal target placement algorithm developed here is the first algorithm of its kind, and it should both improve decode accuracy and help automate target placement for neural prostheses. PMID:18829845

The Fast-spectrum Transmutation Experimental Facility FASTEF: Main design achievements (part 2: Reactor building design and plant layout) within the FP7-CDT collaborative project of the European Commission

DOE Office of Scientific and Technical Information (OSTI.GOV)

De Bruyn, D.; Engelen, J.; Ortega, A.

MYRRHA (Multi-purpose hybrid Research Reactor for High-tech Applications) is the flexible experimental accelerator-driven system (ADS) in development at SCK-CEN in replacement of its material testing reactor BR2. SCK-CEN in association with 17 European partners from industry, research centres and academia, responded to the FP7 (Seventh Framework Programme) call from the European Commission to establish a Central Design Team (CDT) for the design of a Fast Spectrum Transmutation Experimental Facility (FASTEF) able to demonstrate efficient transmutation and associated technology through a system working in subcritical and/or critical mode. The project has started on April 01, 2009 for a period of threemore » years. In this paper, we present the latest concept of the reactor building and the plant layout. The FASTEF facility has evolved quite a lot since the intermediate reporting done at the ICAPP'10 and ICAPP'11 conferences 1,2. Many iterations have been performed to take into account the safety requirements. The present configuration enables an easy operation and maintenance of the facility, including the possibility to change large components of the reactor. In a companion paper 3, we present the latest configuration of the reactor core and primary system. (authors)« less

A systems approach for designing a radio station layout for the U.S. National Airspace

NASA Astrophysics Data System (ADS)

Boci, Erton S.

Today's National Airspace System (NAS) is managed using an aging surveillance radar system. Current radar technology is not adequate to sustain the rapid growth of the commercial, civil, and federal aviation sectors and cannot be adapted to use emerging 21st century airspace surveillance technologies. With 87,000 flights to manage per day, America's ground based radar system has hit a growth ceiling. Consequently, the FAA has embarked on a broad-reaching effort called the Next Generation Air Transportation System (NextGen) that seeks to transform today's aviation airspace management and ensure increased safety and capacity in our NAS. This dissertation presents a systems approach to Service Volume (SV) engineering, a relatively new field of engineering that has emerged in support of the FAA's Automatic Dependent Surveillance -- Broadcast (ADS-B) Air Traffic Modernization Program. SV Engineering is responsible for radio station layout design that would provide the required radio frequency (RF) coverage over a set of Service Volumes, each which represents a section of controlled airspace that is served by a particular air control facility or service. The radio station layout must be optimized to meet system performance, safety, and interference requirements while minimizing the number of radio station sites required to provide RF coverage of the entire airspace of the Unites States. The interference level requirements at the victim (of interference) receivers are the most important and stringent requirements imposed on the ADS-B radio station layout and configuration. In this dissertation, we show a novel and practical way to achieve this optimality by developing and employing several key techniques such as such as reverse radio line-of-site (RLOS) and complex entity-relationship modeling, to address the greater challenges of engineering this complex system. Given that numerous NAS radar facilities are clustered together in relative close proximity to each other, we can optimize site selection placement for coverage through a process of coverage aggregation if we anticipate and leverage the emergent properties that manifest from their aggregation. This optimization process across the NAS significantly reduces the total number of RS sites necessary for complete coverage. Furthermore, in this dissertation, we show the approach taken to develop an entity-relationship model that will support the data capture and distribution of RF SV design. We utilize the CORE software environment to develop a geospatial / RF design entityrelationship (ER) model schema that in conjunction with development of several advanced parsers facilitates effective data management and the communication of complex model logical and parametric detail. Authors note: While the modern standard for scientific papers is to use the International System of Units (SI), this paper was written using the units of measure of the civilian aviation domain to make this research accessible and useful to that community.

Living aboard the Space Shuttle

NASA Technical Reports Server (NTRS)

1984-01-01

The crew habitat of the Space Shuttle is briefly characterized. Subjects discussed include the overall layout of the crew quarters; the air-purification and climate-control facilities; menus and food-preparation techniques; dishwashing, laundry, toilet, bathing, and shaving procedures; and recreation and sleeping accommodations. Drawings and a photograph are provided.

29. SITE BUILDING 002 SCANNER BUILDING FLOOR 3A ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

29. SITE BUILDING 002 - SCANNER BUILDING - FLOOR 3A ("A" FACE) AT SYSTEM LAYOUT GRID 17. GENERAL OBLIQUE VIEW OF "A" FACE INTERIOR SHOWING RADAR EMITTER/ANTENNA INTERFACE ELECTRONICS. - Cape Cod Air Station, Technical Facility-Scanner Building & Power Plant, Massachusetts Military Reservation, Sandwich, Barnstable County, MA

Development of cloud-operating platform for detention facility design

NASA Astrophysics Data System (ADS)

Tun Lee, Kwan; Hung, Meng-Chiu; Tseng, Wei-Fan; Chan, Yi-Ping

2017-04-01

In the past 20 years, the population of Taiwan has accumulated in urban areas. The land development has changed the hydrological environment and resulted in the increase of surface runoff and shortened the time to peak discharge. The change of runoff characteristics increases the flood risk and reduces resilient ability of the city during flood. Considering that engineering measures may not be easy to implement in populated cities, detention facilities set on building basements have been proposed to compromise the increase of surface runoff resulting from development activities. In this study, a web-based operational platform has been developed to integrate the GIS technologies, hydrological analyses, as well as relevant regulations for the design of detention facilities. The design procedure embedded in the system includes a prior selection of type and size of the detention facility, integrated hydrological analysis for the developing site, and inspection of relevant regulations. After login the platform, designers can access the system database to retrieve road maps, land use coverages, and storm sewer information. Once the type, size, inlet, and outlet of the detention facility are assigned, the system can acquire the rainfall intensity-duration-frequency information from adjacent rain gauges to perform hydrological analyses for the developing site. The increase of the runoff volume due to the development and the reduction of the outflow peak through the construction of the detention facility can be estimated. The outflow peak at the target site is then checked with relevant regulations to confirm the suitability of the detention facility design. The proposed web-based platform can provide a concise layout of the detention facility and the drainageway of the developing site on a graphical interface. The design information can also be delivered directly through a web link to authorities for inspecting to simplify the complex administrative procedures.

Production layout improvement in emergency services: a participatory approach.

PubMed

Zanatta, Mateus; Amaral, Fernando Gonçalves

2012-01-01

Volunteer fire department is a service that responds emergency situations in places where there are no military emergency services. These services need to respond quickly, because time is often responsible for the operation success besides work environment and setup time interfere with the prompt response to these calls and care efficiency. The layout design is one factor that interferes with the quick setup. In this case, the spaces arrangement can result in excessive or unnecessary movements; also the equipment provision may hinder the selection and collection of these or even create movement barriers for the workers. This work created a new layout for the emergency assistance service, considering the human factors related to work through the task analysis and workers participation on the alternatives of improvement. The results showed an alternate layout with corridors and minimization of unusable sites, allowing greater flexibility and new possibilities of requirements.

Modeling human-machine interactions for operations room layouts

NASA Astrophysics Data System (ADS)

Hendy, Keith C.; Edwards, Jack L.; Beevis, David

2000-11-01

The LOCATE layout analysis tool was used to analyze three preliminary configurations for the Integrated Command Environment (ICE) of a future USN platform. LOCATE develops a cost function reflecting the quality of all human-human and human-machine communications within a workspace. This proof- of-concept study showed little difference between the efficacy of the preliminary designs selected for comparison. This was thought to be due to the limitations of the study, which included the assumption of similar size for each layout and a lack of accurate measurement data for various objects in the designs, due largely to their notional nature. Based on these results, the USN offered an opportunity to conduct a LOCATE analysis using more appropriate assumptions. A standard crew was assumed, and subject matter experts agreed on the communications patterns for the analysis. Eight layouts were evaluated with the concepts of coordination and command factored into the analysis. Clear differences between the layouts emerged. The most promising design was refined further by the USN, and a working mock-up built for human-in-the-loop evaluation. LOCATE was applied to this configuration for comparison with the earlier analyses.

33 CFR 127.1101 - Piping systems.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Waterfront Facilities Handling Liquefied Hazardous Gas Design and Construction § 127.1101 Piping systems... following criteria: (a) Each system must be designed and constructed in accordance with ASME B31.3. (b) Each... the line or equipment. Unless the layout of the piping allows the isolation valve at the transfer...

33 CFR 127.1101 - Piping systems.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Waterfront Facilities Handling Liquefied Hazardous Gas Design and Construction § 127.1101 Piping systems... following criteria: (a) Each system must be designed and constructed in accordance with ASME B31.3. (b) Each... the line or equipment. Unless the layout of the piping allows the isolation valve at the transfer...

33 CFR 127.1101 - Piping systems.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Waterfront Facilities Handling Liquefied Hazardous Gas Design and Construction § 127.1101 Piping systems... following criteria: (a) Each system must be designed and constructed in accordance with ASME B31.3. (b) Each... the line or equipment. Unless the layout of the piping allows the isolation valve at the transfer...

33 CFR 127.1101 - Piping systems.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Waterfront Facilities Handling Liquefied Hazardous Gas Design and Construction § 127.1101 Piping systems... following criteria: (a) Each system must be designed and constructed in accordance with ASME B31.3. (b) Each... the line or equipment. Unless the layout of the piping allows the isolation valve at the transfer...

33 CFR 127.1101 - Piping systems.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Waterfront Facilities Handling Liquefied Hazardous Gas Design and Construction § 127.1101 Piping systems... following criteria: (a) Each system must be designed and constructed in accordance with ASME B31.3. (b) Each... the line or equipment. Unless the layout of the piping allows the isolation valve at the transfer...

43. Photograph of an original construction drawing, dated October 1927, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

43. Photograph of an original construction drawing, dated October 1927, in the possession of Facilities Planning Office, Iowa State University, Ames, Iowa. GROUND FLOOR PLAN, REFRIGERATION LAYOUT AND DETAILS; SHEET R-1 OF 1 SHEET - Dairy Industry Building, Iowa State University campus, Ames, Story County, IA

Job Grading Standard for Materials Expediter WG-6705.

ERIC Educational Resources Information Center

Civil Service Commission, Washington, DC. Bureau of Policies and Standards.

The standard is used to grade nonsupervisory jobs involved in routing and expediting the movement of parts, end items, supplies, and materials within production and repair facilities to meet priority needs. The work requires knowledge of material characteristics, uses, condition, industrial production shop procedures, shop layout, and internal…

PBF Cubicle 13. Shield wall details illustrate shielding technique of ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

PBF Cubicle 13. Shield wall details illustrate shielding technique of stepped penetrations and brick layout scheme for valve stem extension sleeve. Aerojet Nuclear Company. Date: May 1976. INEEL index no. 761-0620-00-400-195280 - Idaho National Engineering Laboratory, SPERT-I & Power Burst Facility Area, Scoville, Butte County, ID

South Carolina Industrial Arts Safety Guide. Administrator and Instructor Section.

ERIC Educational Resources Information Center

South Carolina State Dept. of Education, Columbia.

This administrator and instructor section of a South Carolina industrial arts safety guide includes sections on responsibility for school safety, safety programming for the teacher, emergency action, suggested forms and outlines, and facility design and layout. School board and superintendent, administrator, and teacher responsibilities for school…

Alternating phase-shifted mask for logic gate levels, design, and mask manufacturing

NASA Astrophysics Data System (ADS)

Liebmann, Lars W.; Graur, Ioana C.; Leipold, William C.; Oberschmidt, James M.; O'Grady, David S.; Regaill, Denis

1999-07-01

While the benefits of alternating phase shifted masks in improving lithographic process windows at increased resolution are well known throughout the lithography community, broad implementation of this potentially powerful technique has been slow due to the inherent complexity of the layout design and mask manufacturing process. This paper will review a project undertaken at IBM's Semiconductor Research and Development Center and Mask Manufacturing and Development facility to understand the technical and logistical issues associated with the application of alternating phase shifted mask technology to the gate level of a full microprocessor chip. The work presented here depicts an important milestone toward integration of alternating phase shifted masks into the manufacturing process by demonstrating an automated design solution and yielding a functional alternating phase shifted mask. The design conversion of the microprocessor gate level to a conjugate twin shifter alternating phase shift layout was accomplished with IBM's internal design system that automatically scaled the design, added required phase regions, and resolved phase conflicts. The subsequent fabrication of a nearly defect free phase shifted mask, as verified by SEM based die to die inspection, highlights the maturity of the alternating phase shifted mask manufacturing process in IBM's internal mask facility. Well defined and recognized challenges in mask inspection and repair remain and the layout of alternating phase shifted masks present a design and data preparation overhead, but the data presented here demonstrate the feasibility of designing and building manufacturing quality alternating phase shifted masks for the gate level of a microprocessor.

CFD simulation of fluid dynamic and biokinetic processes within activated sludge reactors under intermittent aeration regime.

PubMed

Sánchez, F; Rey, H; Viedma, A; Nicolás-Pérez, F; Kaiser, A S; Martínez, M

2018-08-01

Due to the aeration system, biological reactors are the most energy-consuming facilities of convectional WWTPs. Many biological reactors work under intermittent aeration regime; the optimization of the aeration process (air diffuser layout, air flow rate per diffuser, aeration length …) is necessary to ensure an efficient performance; satisfying the effluent requirements with the minimum energy consumption. This work develops a CFD modelling of an activated sludge reactor (ASR) which works under intermittent aeration regime. The model considers the fluid dynamic and biological processes within the ASR. The biological simulation, which is transient, takes into account the intermittent aeration regime. The CFD modelling is employed for the selection of the aeration system of an ASR. Two different aeration configurations are simulated. The model evaluates the aeration power consumption necessary to satisfy the effluent requirements. An improvement of 2.8% in terms of energy consumption is achieved by modifying the air diffuser layout. An analysis of the influence of the air flow rate per diffuser on the ASR performance is carried out. The results show a reduction of 14.5% in the energy consumption of the aeration system when the air flow rate per diffuser is reduced. The model provides an insight into the aeration inefficiencies produced within ASRs. Copyright © 2018 Elsevier Ltd. All rights reserved.

Human factors engineering in oil and gas--a review of industry guidance.

PubMed

Robb, Martin; Miller, Gerald

2012-01-01

Oil and gas exploration and production activities are carried out in hazardous environments in many parts of the world. Recent events in the Gulf of Mexico highlight those risks and underline the importance of considering human factors during facility design. Ergonomic factors such as machinery design, facility and accommodation layout and the organization of work activities have been systematically considered over the past twenty years on a limited number of offshore facility design projects to a) minimize the occupational risks to personnel, b) support operations and maintenance tasks and c) improve personnel wellbeing. During this period, several regulators and industry bodies such as the American Bureau of Shipping (ABS), the American Society of Testing and Materials (ASTM), the UK's Health and Safety Executive (HSE), Oil and Gas Producers (OGP), and Norway's Petroleum Safety Authority (PSA) have developed specific HFE design standards and guidance documents for the application of Human Factors Engineering (HFE) to the design and operation of Oil and Gas projects. However, despite the existence of these guidance and recommended design practise documents, and documented proof of their value in enhancing crew safety and efficiency, HFE is still not well understood across the industry and application across projects is inconsistent. This paper summarizes the key Oil and Gas industry bodies' HFE guidance documents, identifies recurring themes and current trends in the use of these standards, provides examples of where and how these HFE standards have been used on past major offshore facility design projects, and suggests criteria for selecting the appropriate HFE strategy and tasks for future major oil and gas projects. It also provides a short history of the application of HFE to the offshore industry, beginning with the use of ASTM F 1166 to a major operator's Deepwater Gulf of Mexico facility in 1990 and the application of HFE to diverse world regions. This latter point highlights the need to consider user populations when selecting HFE design criteria, an aspect strongly emphasized in current industry guidance.

The laboratory astrophysics facility at University College

NASA Astrophysics Data System (ADS)

Hyland, A. R.; Smith, R. G.; Robinson, G.

A laboratory astrophysics facility for the study of the terrestrial analogues of interstellar dust grains is being developed in the Physics Department, University College, Australian Defence Force Academy. The facility consists of a gas handling system for the preparation of samples, a closed-cycle cooler and specimen chamber, and a Fourier Transform Infrared (FTIR) Spectrometer capable of high resolution (0.3/cm) and high sensitivity measurements, currently from 1-25 microns. The layout and construction of the laboratory are described, and the proposed initial experimental program aimed at determining the optical constants of ices, over a wide wavelength range for comparison with astronomical observations, is discussed.

LAFD: TA-15 DARHT Firefighter Facility Familiarization Tour, OJT 53044, Revision 0.2

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rutherford, Victor Stephen; Priestley, Terry B.; Maestas, Marvin Manuel

The Los Alamos National Laboratory (LANL or the Lab) will conduct familiarization tours for the Los Alamos County Fire Department (LAFD) at the Dual-Axis Radiographic Hydrodynamic Test (DARHT) Facility, TA-15-0312. The purpose of these tours is to orient LAFD firefighters to the DARHT facility layout and hazards. This document provides information and figures to supplement the familiarization tours. The document will be distributed to the trainees at the time of the familiarization tour. A checklist (Attachment A) has also been developed to ensure that all required information is consistently presented to LAFD personnel during the familiarization tours.

Voting with Their Seats: Computer Laboratory Design and the Casual User

ERIC Educational Resources Information Center

Spennemann, Dirk H. R.; Atkinson, John; Cornforth, David

2007-01-01

Student computer laboratories are provided by most teaching institutions around the world; however, what is the most effective layout for such facilities? The log-in data files from computer laboratories at a regional university in Australia were analysed to determine whether there was a pattern in student seating. In particular, it was…

51. Photograph of an original construction drawing, dated August 1927, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

51. Photograph of an original construction drawing, dated August 1927, in the possession of Facilities planning Office, Iowa State University, Ames, Iowa. GROUND FLOOR PLAN, MECHANICAL FAN ROOM LAYOUT, ELECTRICAL WIRING DIAGRAM, RADIATOR, FANS 1 & 2, DETAILS; SHEET NO. 202 OF 3 - Dairy Industry Building, Iowa State University campus, Ames, Story County, IA

Library Automation and Facility Planning.

ERIC Educational Resources Information Center

Cohen, Aaron; Cohen, Elaine

This seminar and workbook are designed to aid librarians in planning and designing attractive and efficient libraries in light of the changing technologies of the 1980s. It is based on the premise that the electronic revolution of the 1980s will cause substantial changes in the work force, work processes, and the nature of physical layouts of…

Child Care Center Design & the Potential of Architecture.

ERIC Educational Resources Information Center

Abbott, Carl; Abbott, Cooper

This paper discusses the impact of layout and design of child care centers on the education of young children. It asserts that child care facilities must be designed to support and stimulate children's natural developmental processes, providing both direct and indirect educational opportunities. The paper discusses the stages of the design process…

As-built data capture of complex piping using photogrammetry technology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Morray, J.P.; Ziu, C.G.

1995-11-01

Plant owners face an increasingly difficult and expensive task of updating drawings, both regarding the plant logic and physical layout. Through the use of photogrammetry technology, H-H spectrum has created a complete operating plant data capture service, with the result that the task of recording accurate plant configurations has become assured and economical. The technology has proven to be extremely valuable for the capture of complex piping configurations, as well as entire plant facilities, and yields accuracy within 1/4 inch. The method uses photographs and workstation technology to quickly document and compute the plant layout, with all components, regardless ofmore » size, included in the resulting model. The system has the capability to compute actual 3-D coordinates of any point based on previous triangulations, allowing for an immediate assessment of accuracy. This ensures a consistent level of accuracy, which is impossible to achieve in a manual approach. Due to the speed of the process, the approach is very important in hazardous/difficult environments such as nuclear power facilities or offshore platforms.« less

Wind Farm Layout Optimization through a Crossover-Elitist Evolutionary Algorithm performed over a High Performing Analytical Wake Model

NASA Astrophysics Data System (ADS)

Kirchner-Bossi, Nicolas; Porté-Agel, Fernando

2017-04-01

Wind turbine wakes can significantly disrupt the performance of further downstream turbines in a wind farm, thus seriously limiting the overall wind farm power output. Such effect makes the layout design of a wind farm to play a crucial role on the whole performance of the project. An accurate definition of the wake interactions added to a computationally compromised layout optimization strategy can result in an efficient resource when addressing the problem. This work presents a novel soft-computing approach to optimize the wind farm layout by minimizing the overall wake effects that the installed turbines exert on one another. An evolutionary algorithm with an elitist sub-optimization crossover routine and an unconstrained (continuous) turbine positioning set up is developed and tested over an 80-turbine offshore wind farm over the North Sea off Denmark (Horns Rev I). Within every generation of the evolution, the wind power output (cost function) is computed through a recently developed and validated analytical wake model with a Gaussian profile velocity deficit [1], which has shown to outperform the traditionally employed wake models through different LES simulations and wind tunnel experiments. Two schemes with slightly different perimeter constraint conditions (full or partial) are tested. Results show, compared to the baseline, gridded layout, a wind power output increase between 5.5% and 7.7%. In addition, it is observed that the electric cable length at the facilities is reduced by up to 21%. [1] Bastankhah, Majid, and Fernando Porté-Agel. "A new analytical model for wind-turbine wakes." Renewable Energy 70 (2014): 116-123.

Geometrical layout and optics modelling of the surface science beamline station at the SESAME synchrotron radiation facility.

PubMed

Salah, Wa'el; Sanchez del Rio, Manuel

2011-05-01

The layout and the optical performance of the SGM branch of the D09 bending-magnet beamline, under construction at SESAME, are presented. The beamline is based on the Dragon-type design and delivers photons over the spectral range 15-250 eV. One fixed entrance slit and a movable exit slit are used. The performance of the beamline has been characterized by calculating the mirror reflectivities and the grating efficiencies. The flux and resolution were calculated by ray-tracing using SHADOW. The grating diffraction efficiencies were calculated using the GRADIF code. The results and the overall shapes of the predicted curves are in reasonable agreement with those obtained using an analytical formula.

Liquid rocket booster study. Volume 2, book 4, appendices 6-8: Reports of Rocketdyne, Pratt and Whitney, and TRW

NASA Technical Reports Server (NTRS)

1988-01-01

For the pressure fed engines, detailed trade studies were conducted defining engine features such as thrust vector control methods, thrust chamber construction, etc. This was followed by engine design layouts and booster propulsion configuration layouts. For the pump fed engines parametric performance and weight data was generated for both O2/H2 and O2/RP-1 engines. Subsequent studies resulted in the selection of both LOX/RP-1 and O2/H2 propellants for the pump fed engines. More detailed analysis of the selected LOX/RP-1 and O2/H2 engines was conducted during the final phase of the study.

Variability-aware double-patterning layout optimization for analog circuits

NASA Astrophysics Data System (ADS)

Li, Yongfu; Perez, Valerio; Tripathi, Vikas; Lee, Zhao Chuan; Tseng, I.-Lun; Ong, Jonathan Yoong Seang

2018-03-01

The semiconductor industry has adopted multi-patterning techniques to manage the delay in the extreme ultraviolet lithography technology. During the design process of double-patterning lithography layout masks, two polygons are assigned to different masks if their spacing is less than the minimum printable spacing. With these additional design constraints, it is very difficult to find experienced layout-design engineers who have a good understanding of the circuit to manually optimize the mask layers in order to minimize color-induced circuit variations. In this work, we investigate the impact of double-patterning lithography on analog circuits and provide quantitative analysis for our designers to select the optimal mask to minimize the circuit's mismatch. To overcome the problem and improve the turn-around time, we proposed our smart "anchoring" placement technique to optimize mask decomposition for analog circuits. We have developed a software prototype that is capable of providing anchoring markers in the layout, allowing industry standard tools to perform automated color decomposition process.

Space station functional relationships analysis

NASA Technical Reports Server (NTRS)

Tullis, Thomas S.; Bied, Barbra R.

1988-01-01

A systems engineering process is developed to assist Space Station designers to understand the underlying operational system of the facility so that it can be physically arranged and configured to support crew productivity. The study analyzes the operational system proposed for the Space Station in terms of mission functions, crew activities, and functional relationships in order to develop a quantitative model for evaluation of interior layouts, configuration, and traffic analysis for any Station configuration. Development of the model involved identification of crew functions, required support equipment, criteria of assessing functional relationships, and tools for analyzing functional relationship matrices, as well as analyses of crew transition frequency, sequential dependencies, support equipment requirements, potential for noise interference, need for privacy, and overall compatability of functions. The model can be used for analyzing crew functions for the Initial Operating Capability of the Station and for detecting relationships among these functions. Note: This process (FRA) was used during Phase B design studies to test optional layouts of the Space Station habitat module. The process is now being automated as a computer model for use in layout testing of the Space Station laboratory modules during Phase C.

THE CONCEPTUAL DESIGN ASSESSMENT FOR THE CO-FIRING OF BIO-REFINERY SUPPLIED LIGNIN PROJECT

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ted Berglund; Jeffrey T. Ranney; Carol L. Babb

2001-07-01

The major aspects of this project are proceeding toward completion. Prior to this quarter, design criteria, tentative site selection, facility layout, and preliminary facility cost estimates were completed and issued. Processing of bio-solids was completed, providing material for the pilot operations. Pilot facility design, equipment selection, and modification were completed during the fourth quarter of 2000. Initial pilot facility shakedown was completed during the fourth quarter. After some unavoidable delays, a suitable representative supply of MSW feed material was procured. During this first quarter of 2001, shredding of the feed material and final feed conditioning were completed. Pilot facility hydrolysismore » production was completed to produce lignin for co-fire testing. During this quarter, TVA completed the washing and dewatering of the lignin material produced from the MSW hydrolysis. Seven drums of lignin material were washed to recover the acid and sugar from the lignin and provide an improved fuel for steam generation. Samples of both the lignin and bio-solids fuel materials for co-fire testing were sent to the co-fire facility (EERC) for evaluation. After sample evaluation, EERC approved sending the material and all of the necessary fuel for testing was shipped to EERC. EERC has requested and will receive coal typical of the fuel to the TVA-Colbert boilers. This material will be used at EERC as baseline material and for mixing with the bio-fuel for combustion testing. EERC combustion testing of the bio based fuels is scheduled to begin in August of 2001. The TVA-Colbert facility has neared completion of the task to evaluate the co-location of the Masada facility on the operation of the power generation facility. The TVA-Colbert fossil plant is fully capable of providing a reliable steam supply. The preferred steam supply connection points and steam pipeline routing have been identified. The environmental review of the pipeline routing has been completed and no major impacts have been identified. Detailed assessment of steam export impacts on the Colbert boiler system have been completed and a cost estimate for steam supply system was completed. The cost estimate and the output and heat rate impacts will be used to determine a preliminary price for the exported steam. The preliminary steam price will be determined in the next quarter.« less

Using a 3D CAD plant model to simplify process hazard reviews

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tolpa, G.

A Hazard and Operability (HAZOP) review is a formal predictive procedure used to identify potential hazard and operability problems associated with certain processes and facilities. The HAZOP procedure takes place several times during the life cycle of the facility. Replacing plastic models, layout and detail drawings with a 3D CAD electronic model, provides access to process safety information and a detailed level of plant topology that approaches the visualization capability of the imagination. This paper describes the process that is used for adding the use of a 3D CAD model to flowsheets and proven computer programs for the conduct ofmore » hazard and operability reviews. Using flowsheets and study nodes as a road map for the review the need for layout and other detail drawings is all but eliminated. Using the 3D CAD model again for a post-P and ID HAZOP supports conformance to layout and safety requirements, provides superior visualization of the plant configuration and preserves the owners equity in the design. The response from the review teams are overwhelmingly in favor of this type of review over a review that uses only drawings. Over the long term the plant model serves more than just process hazards analysis. Ongoing use of the model can satisfy the required access to process safety information, OHSA documentation and other legal requirements. In this paper extensive instructions address the logic for the process hazards analysis and the preparation required to assist anyone who wishes to add the use of a 3D model to their review.« less

Empirical Performance Model-Driven Data Layout Optimization and Library Call Selection for Tensor Contraction Expressions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lu, Qingda; Gao, Xiaoyang; Krishnamoorthy, Sriram

Empirical optimizers like ATLAS have been very effective in optimizing computational kernels in libraries. The best choice of parameters such as tile size and degree of loop unrolling is determined by executing different versions of the computation. In contrast, optimizing compilers use a model-driven approach to program transformation. While the model-driven approach of optimizing compilers is generally orders of magnitude faster than ATLAS-like library generators, its effectiveness can be limited by the accuracy of the performance models used. In this paper, we describe an approach where a class of computations is modeled in terms of constituent operations that are empiricallymore » measured, thereby allowing modeling of the overall execution time. The performance model with empirically determined cost components is used to perform data layout optimization together with the selection of library calls and layout transformations in the context of the Tensor Contraction Engine, a compiler for a high-level domain-specific language for expressing computational models in quantum chemistry. The effectiveness of the approach is demonstrated through experimental measurements on representative computations from quantum chemistry.« less

An Arsenal Ship Design

DTIC Science & Technology

1996-12-01

151 B. PROPULSION PLANT SELECTION....................................................................... 152 ix C. PROPULSION PLANT LAYOUT...155 D. ELECTRICAL PLANT SELECTION...designed into the hull and power plant and once finalized is only a function of how many miles the ship is to be driven. Decision trade- offs are to

Concept definition study for an extremely large aerophysics range facility

NASA Technical Reports Server (NTRS)

Swift, H.; Witcofski, R.

1992-01-01

The development of a large aerophysical ballistic range facility is considered to study large-scale hypersonic flows at high Reynolds numbers for complex shapes. A two-stage light gas gun is considered for the hypervelocity launcher, and the extensive range tankage is discussed with respect to blast suppression, model disposition, and the sabot impact tank. A layout is given for the large aerophysics facility, and illustrations are provided for key elements such as the guide rail. The paper shows that such a facility could be used to launch models with diameters approaching 250 mm at velocities of 6.5 km/s with peak achievable accelerations of not more than 85.0 kgs. The envisioned range would provide gas-flow facilities capable of controlling the modeled quiescent atmospheric conditions. The facility is argued to be a feasible and important step in the investigation and experiment of such hypersonic vehicles as the National Aerospace Plane.

Computer code for analyzing the performance of aquifer thermal energy storage systems

NASA Astrophysics Data System (ADS)

Vail, L. W.; Kincaid, C. T.; Kannberg, L. D.

1985-05-01

A code called Aquifer Thermal Energy Storage System Simulator (ATESSS) has been developed to analyze the operational performance of ATES systems. The ATESSS code provides an ability to examine the interrelationships among design specifications, general operational strategies, and unpredictable variations in the demand for energy. The uses of the code can vary the well field layout, heat exchanger size, and pumping/injection schedule. Unpredictable aspects of supply and demand may also be examined through the use of a stochastic model of selected system parameters. While employing a relatively simple model of the aquifer, the ATESSS code plays an important role in the design and operation of ATES facilities by augmenting experience provided by the relatively few field experiments and demonstration projects. ATESSS has been used to characterize the effect of different pumping/injection schedules on a hypothetical ATES system and to estimate the recovery at the St. Paul, Minnesota, field experiment.

Circulation and Library Design: The Influence of 'Movement' on the Layout of Libraries.

ERIC Educational Resources Information Center

Marples, D. L.; Knell, K. A.

The movement of people in a library is inevitably noisy and also creates a visual distraction for the reader. If the provision of quiet areas where readers can work undisturbed is an important criterion of library design, the traffic patterns generated in a library by the disposition of the various facilities - stacks, periodicals, reference…

KSC-2013-1528

NASA Image and Video Library

2013-02-15

CAPE CANAVERAL, Fla. – An artist's concept shows a possible layout of a commercial spacecraft and rocket using facilities at Launch Pad 39A as NASA's Kennedy Space Center in Florida undergoes a transformation into a multi-user spaceport. Several companies are designing rockets and spacecraft that could be used to launch astronauts and payloads into space in the future. Credit: NASA

Layout, Equipment, and Work Methods for School Lunch Kitchens and Serving Lines.

ERIC Educational Resources Information Center

Biedermann, Konrad; And Others

The objectives of this study include the development of (1) guides for the planning and the remodeling of new school kitchens and lunchroom facilities and (2) standards of labor utilization for three sizes of cafeterias. The data reflect the results of over six weeks of observation and measurement of operations in various school kitchens,…

Quantitative assessment of energy and resource recovery in wastewater treatment plants based on plant-wide simulations.

PubMed

Fernández-Arévalo, T; Lizarralde, I; Fdz-Polanco, F; Pérez-Elvira, S I; Garrido, J M; Puig, S; Poch, M; Grau, P; Ayesa, E

2017-07-01

The growing development of technologies and processes for resource treatment and recovery is offering endless possibilities for creating new plant-wide configurations or modifying existing ones. However, the configurations' complexity, the interrelation between technologies and the influent characteristics turn decision-making into a complex or unobvious process. In this frame, the Plant-Wide Modelling (PWM) library presented in this paper allows a thorough, comprehensive and refined analysis of different plant configurations that are basic aspects in decision-making from an energy and resource recovery perspective. In order to demonstrate the potential of the library and the need to run simulation analyses, this paper carries out a comparative analysis of WWTPs, from a techno-economic point of view. The selected layouts were (1) a conventional WWTP based on a modified version of the Benchmark Simulation Model No. 2, (2) an upgraded or retrofitted WWTP, and (3) a new Wastewater Resource Recovery Facilities (WRRF) concept denominated as C/N/P decoupling WWTP. The study was based on a preliminary analysis of the organic matter and nutrient energy use and recovery options, a comprehensive mass and energy flux distribution analysis in each configuration in order to compare and identify areas for improvement, and a cost analysis of each plant for different influent COD/TN/TP ratios. Analysing the plants from a standpoint of resources and energy utilization, a low utilization of the energy content of the components could be observed in all configurations. In the conventional plant, the COD used to produce biogas was around 29%, the upgraded plant was around 36%, and 34% in the C/N/P decoupling WWTP. With regard to the self-sufficiency of plants, achieving self-sufficiency was not possible in the conventional plant, in the upgraded plant it depended on the influent C/N ratio, and in the C/N/P decoupling WWTP layout self-sufficiency was feasible for almost all influents, especially at high COD concentrations. The plant layouts proposed in this paper are just a sample of the possibilities offered by current technologies. Even so, the library presented here is generic and can be used to construct any other plant layout, provided that a model is available. Copyright © 2017 Elsevier Ltd. All rights reserved.

Semantic photo books: leveraging blogs and social media for photo book creation

NASA Astrophysics Data System (ADS)

Rabbath, Mohamad; Sandhaus, Philipp; Boll, Susanne

2011-03-01

Recently, we observed a substantial increase in the users' interest in sharing their photos online in travel blogs, social communities and photo sharing websites. An interesting aspect of these web platforms is their high level of user-media interaction and thus a high-quality source of semantic annotations: Users comment on the photos of each others, add external links to their travel blogs, tag each other in the social communities and add captions and descriptions to their photos. However, while those media assets are shared online, many users still highly appreciate the representation of these media in appealing physical photo books where the semantics are represented in form of descriptive text, maps, and external elements in addition to their related photos. Thus, in this paper we aim at fulfilling this need and provide an approach for creating photo books from Web 2.0 resources. We concentrate on two kinds of online shared media as resources for printable photo books: (a) Blogs especially travel blogs (b) Social community websites like Facebook which witness a rapidly growing number of shared media elements including photos. We introduce an approach to select media elements including photos, geographical maps and texts from both blogs and social networks semi-automatically, and then use these elements to create a printable photo book with an appealing layout. Because the selected media elements can be too many for the resulting book, we choose the most proper ones by exploiting content based, social based, and interactive based criteria. Additionally we add external media elements such as geographical maps, texts and externally hosted photos from linked resources. Having selected the important media, our approach uses a genetic algorithm to create an appealing layout using aesthetical rules, such as positioning the photo with the related text or map in a way that respects the golden ratio and symmetry. Distributing the media over the pages is done by optimizing the distribution according to several rules such that no pages with purely textual elements without photos are produced. For the page layout appropriate photos are chosen for the background based on their salience. Other media assets, such as texts, photos and geographical maps are positioned in the foreground by a dynamic page layout algorithm respecting both the content of the photos and the background, and common rules for visual layout. The result of our system is a photo book in a printable format. We implemented our approach as web services that analyze the media elements, enrich them, and create the layout in order to finally publish a photo book. The connection to those services is implemented in two interfaces. The first is a tool to select entries from personal blogs, and the second is a Facebook application that allows the user to select photos from his albums.

Solid waste management complex site development plan

DOE Office of Scientific and Technical Information (OSTI.GOV)

Greager, T.M.

1994-09-30

The main purpose of this Solid Waste Management Complex Site Development Plan is to optimize the location of future solid waste treatment and storage facilities and the infrastructure required to support them. An overall site plan is recommended. Further, a series of layouts are included that depict site conditions as facilities are constructed at the SWMC site. In this respect the report serves not only as the siting basis for future projects, but provides siting guidance for Project W-112, as well. The plan is intended to function as a template for expected growth of the site over the next 30more » years so that future facilities and infrastructure will be properly integrated.« less

Human Factors Evaluations of Two-Dimensional Spacecraft Conceptual Layouts

NASA Technical Reports Server (NTRS)

Kennedy, Kriss J.; Toups, Larry D.; Rudisill, Marianne

2010-01-01

Much of the human factors work done in support of the NASA Constellation lunar program has been with low fidelity mockups. These volumetric replicas of the future lunar spacecraft allow researchers to insert test subjects from the engineering and astronaut population and evaluate the vehicle design as the test subjects perform simulations of various operational tasks. However, lunar outpost designs must be evaluated without the use of mockups, creating a need for evaluation tools that can be performed on two-dimension conceptual spacecraft layouts, such as floor plans. A tool based on the Cooper- Harper scale was developed and applied to one lunar scenario, enabling engineers to select between two competing floor plan layouts. Keywords: Constellation, human factors, tools, processes, habitat, outpost, Net Habitable Volume, Cooper-Harper.

Occupational Training in Selected Metalworking Industries, 1974. A Report on a Survey of Selected Occupations.

ERIC Educational Resources Information Center

Bureau of Labor Statistics (DOL), New York, NY.

A survey was conducted regarding the occupational training provided by employers for fourteen occupations in four metalworking industries. The fourteen occupations selected for study included crane operator, electrician, layout worker, machine tool setter, machinist, mechanic, sheet metal worker, and tool and die maker. The four industries…

On the possibility for precision measurements of differential cross sections for elastic proton–proton scattering at the Protvino accelerator

DOE Office of Scientific and Technical Information (OSTI.GOV)

Denisov, S. P., E-mail: denisov@ihep.ru; Kozelov, A. V.; Petrov, V. A.

Elastic-scattering data were analyzed, and it was concluded on the basis of this analysis that precisionmeasurements of differential cross sections for elastic proton–proton scattering at the accelerator of the Institute for High Energy Physics (IHEP, Protvino, Russia) over a broad momentum-transfer range are of importance and topical interest. The layout of the respective experimental facility detecting the scattered particle and recoil proton and possessing a high momentum-transfer resolution was examined along with the equipment constituting this facility. The facility in question is able to record up to a billion events of elastic proton–proton scattering per IHEP accelerator run (20 days).more » Other lines of physics research with this facility are briefly discussed.« less

Re-engineering a pharmacy work system and layout to facilitate patient counseling.

PubMed

Lin, A C; Jang, R; Sedani, D; Thomas, S; Barker, K N; Flynn, E A

1996-07-01

The development and evaluation of a new work system and facility design for a chain of community pharmacies are described. A new work system was developed to optimize utilization of pharmacist and technician time and allow the pharmacy to increase patient counseling without adding personnel. In the new system, pharmacists would review prescriptions, check technicians' work, and dispense prescriptions, counseling patients as needed; technicians would enter prescriptions into the pharmacy computer and fill them. The existing work system and design were evaluated in June and July of 1992 by observing, classifying, and recording activities of pharmacy personnel three days per week at six pharmacies in the chain. Pharmacy designs that would work with the new work system were created by a university design class after consultation with representatives of the pharmacy chain and the university's college of pharmacy. The pharmacy chain selected one design, and a detailed floor plan and specifications were created. To test how the new design and system would work at each of the six test pharmacies, a computer simulation program was developed and verified by using the data collected on the existing pharmacy operations. Computer simulation showed that, with the new design and system, increasing patient counseling would increase patient waiting time slightly but would not require additional personnel. The layout and work system in a chain of community pharmacies were redesigned to facilitate patient counseling and make the best use of employee time.

Optical performance considerations for analysis and simulation of power tower plants

NASA Astrophysics Data System (ADS)

Pidaparthi, Arvind; Landman, Willem; Hoffmann, Jaap; Dinter, Frank

2017-06-01

South Africa has implemented a `time of day' tariff structure for concentrating solar power plants in the Renewable Energy Independent Power Producer Procurement Programme. It is hypothesised that payment allocation factors for the `time of day' and the `time of use' dispatch schedule influence the optimal heliostat field layout. SolarPILOT software is used to generate and optimize the heliostat field layout of a 100 MWe power tower plant in Upington, South Africa with 8 hours of thermal energy storage in the SunShot scenario with a high receiver thermal efficiency of 90%. A large size heliostat with a total area of 115.56 m2 and an external cylindrical receiver are considered for the heliostat field layout. A subset of 12 days is simulated on an hourly basis to achieve convergence and to take seasonal, daily and hourly weather variability into account. During the optimization of a heliostat field layout, the heliostats are ranked and selected according to a performance metric. In this study, two field layouts are compared based on two different performance metrics, namely: power delivered to the receiver and the time of use weighted power. The optical performance is simulated using both the Hermite (analytical) and the Monte-Carlo Ray-Tracing methods. By accounting for the TOU weighted power, it is found that the LCOE increases from 0.1831 /kWh to 0.1870 /kWh using the Hermite (analytical) method. Similarly, when MCRT techniques are used for the optical characterization, the LCOE value increases from 0.1781 /kWh to 0.1832 /kWh. It is recommended that payment allocation factors and the tariff structure for the time of day be included when comparing field layouts with other layout generation and optimization strategies. This study will be useful for power tower developers in identifying practices to be included in the optical characterization of their heliostat field layouts for better simulation results.

PATIKAweb: a Web interface for analyzing biological pathways through advanced querying and visualization.

PubMed

Dogrusoz, U; Erson, E Z; Giral, E; Demir, E; Babur, O; Cetintas, A; Colak, R

2006-02-01

Patikaweb provides a Web interface for retrieving and analyzing biological pathways in the Patika database, which contains data integrated from various prominent public pathway databases. It features a user-friendly interface, dynamic visualization and automated layout, advanced graph-theoretic queries for extracting biologically important phenomena, local persistence capability and exporting facilities to various pathway exchange formats.

7. Photograph of a line drawing. 'PART III, SECTION 1, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

7. Photograph of a line drawing. 'PART III, SECTION 1, EQUIPMENT LAYOUT, BUILDING NO. 10, PRODUCER GAS & EXHAUSTER BLDG., PLANT A.' From U.S. Army Corps of Engineers. Industrial Facilities Inventory, Holston Ordnance Works, Kingsport, Tennessee. Plant A, Parts I, II, III. (Nashville, TN: Office of District Engineer, 1944). - Holston Army Ammunition Plant, Producer Gas Plant, Kingsport, Sullivan County, TN

A Sharp methodology for VLSI layout

NASA Astrophysics Data System (ADS)

Bapat, Shekhar

1993-01-01

The layout problem for VLSI circuits is recognized as a very difficult problem and has been traditionally decomposed into the several seemingly independent sub-problems of placement, global routing, and detailed routing. Although this structure achieves a reduction in programming complexity, it is also typically accompanied by a reduction in solution quality. Most current placement research recognizes that the separation is artificial, and that the placement and routing problems should be solved ideally in tandem. We propose a new interconnection model, Sharp and an associated partitioning algorithm. The Sharp interconnection model uses a partitioning shape that roughly resembles the musical sharp 'number sign' and makes extensive use of pre-computed rectilinear Steiner trees. The model is designed to generate strategic routing information along with the partitioning results. Additionally, the Sharp model also generates estimates of the routing congestion. We also propose the Sharp layout heuristic that solves the layout problem in its entirety. The Sharp layout heuristic makes extensive use of the Sharp partitioning model. The use of precomputed Steiner tree forms enables the method to model accurately net characteristics. For example, the Steiner tree forms can model both the length of the net and more importantly its route. In fact, the tree forms are also appropriate for modeling the timing delays of nets. The Sharp heuristic works to minimize both the total layout area by minimizing total net length (thus reducing the total wiring area), and the congestion imbalances in the various channels (thus reducing the unused or wasted channel area). Our heuristic uses circuit element movements amongst the different partitioning blocks and selection of alternate minimal Steiner tree forms to achieve this goal. The objective function for the algorithm can be modified readily to include other important circuit constraints like propagation delays. The layout technique first computes a very high-level approximation of the layout solution (i.e., the positions of the circuit elements and the associated net routes). The approximate solution is alternately refined, objective function. The technique creates well defined sub-problems and offers intermediary steps that can be solved in parallel, as well as a parallel mechanism to merge the sub-problem solutions.

High Temperature Electrolysis 4 kW Experiment Design, Operation, and Results

DOE Office of Scientific and Technical Information (OSTI.GOV)

J.E. O'Brien; X. Zhang; K. DeWall

2012-09-01

This report provides results of long-term stack testing completed in the new high-temperature steam electrolysis multi-kW test facility recently developed at INL. The report includes detailed descriptions of the piping layout, steam generation and delivery system, test fixture, heat recuperation system, hot zone, instrumentation, and operating conditions. This facility has provided a demonstration of high-temperature steam electrolysis operation at the 4 kW scale with advanced cell and stack technology. This successful large-scale demonstration of high-temperature steam electrolysis will help to advance the technology toward near-term commercialization.

The Children's Book Showcase, 1976.

ERIC Educational Resources Information Center

Children's Book Council, New York, NY.

The Children's Book Council of New York presents outstanding books for 1976 in the Children's Book Showcase 1976 catalog. Selection criteria place heavy emphasis on illustration, typography, layout, binding, paper, printing, and reproduction, with vitality and originality also considered. The two-page spread for each of the 28 selections contains…

Bipolar electrode selection for a motor imagery based brain computer interface

NASA Astrophysics Data System (ADS)

Lou, Bin; Hong, Bo; Gao, Xiaorong; Gao, Shangkai

2008-09-01

A motor imagery based brain-computer interface (BCI) provides a non-muscular communication channel that enables people with paralysis to control external devices using their motor imagination. Reducing the number of electrodes is critical to improving the portability and practicability of the BCI system. A novel method is proposed to reduce the number of electrodes to a total of four by finding the optimal positions of two bipolar electrodes. Independent component analysis (ICA) is applied to find the source components of mu and alpha rhythms, and optimal electrodes are chosen by comparing the projection weights of sources on each channel. The results of eight subjects demonstrate the better classification performance of the optimal layout compared with traditional layouts, and the stability of this optimal layout over a one week interval was further verified.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Delahaye, J-P.; Ankenbrandt, C.; Bogacz, A.

A Neutrino Factory where neutrinos of all species are produced in equal quantities by muon decay is described as a facility at the intensity frontier for exquisite precision providing ideal conditions for ultimate neutrino studies and the ideal complement to Long Baseline Facilities like LBNF at Fermilab. It is foreseen to be built in stages with progressively increasing complexity and performance, taking advantage of existing or proposed facilities at an existing laboratory like Fermilab. A tentative layout based on a recirculating linac providing opportunities for considerable saving is discussed as well as its possible evolution toward a muon collider ifmore » and when requested by Physics. Tentative parameters of the various stages are presented as well as the necessary R&D to address the technological issues and demonstrate their feasibility.« less

The Impact of Environmental Design on Teamwork and Communication in Healthcare Facilities: A Systematic Literature Review.

PubMed

Gharaveis, Arsalan; Hamilton, D Kirk; Pati, Debajyoti

2018-01-01

The purpose of this systematic review is to investigate the current knowledge about the impact of healthcare facility design on teamwork and communication by exploring the relevant literature. Teamwork and communication are behavioral factors that are impacted by physical design. However, the effects of environmental factors on teamwork and communication have not been investigated extensively in healthcare design literature. There are no published systematic reviews on the current topic. Searches were conducted in PubMed and Google Scholar databases in addition to targeted design journals including Health Environmental Research & Design, Environment and Behavior, Environmental Psychology, and Applied Ergonomics. Inclusion criteria were (a) full-text English language articles related to teamwork and communication and (b) involving any healthcare built environment and space design published in peer-reviewed journals between 1984 and 2017. Studies were extracted using defined inclusion and exclusion criteria. In the first phase, 26 of the 195 articles most relevant to teamwork and 19 studies of the 147 were identified and reviewed to understand the impact of communication in healthcare facilities. The literature regarding the impact of built environment on teamwork and communication were reviewed and explored in detail. Eighteen studies were selected and succinctly summarized as the final product of this review. Environmental design, which involves nurses, support staff, and physicians, is one of the critical factors that promotes the efficiency of teamwork and collaborative communication. Layout design, visibility, and accessibility levels are the most cited aspects of design which can affect the level of communication and teamwork in healthcare facilities.

Evaluation of the built environment: staff and family satisfaction pre- and post-occupancy of the Children's Hospital.

PubMed

Kotzer, Anne Marie; Zacharakis, Susan Koch; Raynolds, Mary; Buenning, Fred

2011-01-01

To evaluate and compare the impact of an existing and newly built hospital environment on family and staff satisfaction related to light, noise, temperature, aesthetics, and amenities, as well as safety, security, and privacy. The United States is engaged in an unprecedented healthcare building boom driven by the need to replace aging facilities, understand the impact of the built environment on quality and safety, incorporate rapidly emerging technologies, and enhance patient- and family-centered care. More importantly, there is heightened attention to creating optimal physical environments to achieve the best possible outcomes for patients, families, and staff. Using a pre-post descriptive survey design, all nursing, social work, therapy staff, and families on selected inpatient units were invited to participate. A demographic form and Family and Staff Satisfaction Surveys were developed and administered pre- and post-occupancy of the new facility. Pre/post mean scores for staff satisfaction improved on all survey subscales with statistically significant improvement (p < .05) in most areas. The most improvement was seen with layout of the patient room, natural light, storage and writing surfaces, and comfort and appeal. Family satisfaction demonstrated statistically significant improvement on all subscales (p ≤ .01), especially for natural light, quiet space, parking, and the child's room as a healing environment. Families and staff reported greater satisfaction with the newly built hospital environment compared to the old facility. Study results will help guide future architectural design decisions, attract and retain staff at a world-class facility, and create the most effective healing environments.

Roads and Airfields I (Programed Instruction). Engineer Subcourse 64-9.

ERIC Educational Resources Information Center

Army Engineer School, Fort Belvoir, VA.

The document is a programed text for a correspondence course in the planning, construction, and maintenance of military roads and airfields. There are seven lessons: construction requirements and design criteria; road reconnaissance and site selection; airfield reconnaissance and site selection; layout procedures, construction staking, and field…

CONCEPTUAL DESIGN ASSESSMENT FOR THE COFIRING OF BIOREFINERY SUPPLIED LIGNIN PROJECT

DOE Office of Scientific and Technical Information (OSTI.GOV)

David J. Webster; Jeffrey T. Ranney; Jacqueline G. Broder

2002-07-01

The major aspects of this project are proceeding toward completion. Prior to this quarter, design criteria, tentative site selection, facility layout, and preliminary facility cost estimates were completed. Processing of biosolids and pilot facility hydrolysis production have been completed to produce lignin for cofire testing. EERC had received all the biomass and baseline coal fuels for use in testing. All the combustion and fuel handling tests at EERC have been completed. During fuel preparation EERC reported no difficulties in fuel blending and handling. Preliminary cofire test results indicate that the blending of lignin and biosolids with the Colbert coal blendmore » generally reduces NOx emissions, increases the reactivity of the coal, and increases the ash deposition rate on superheater surfaces. Deposits produced from the fuel blends, however, are more friable and hence easier to remove from tube surfaces relative to those produced from the baseline Colbert coal blend. A draft of the final cofire technical report entitled ''Effects of Cofiring Lignin and Biosolids with Coal on Fireside Performance and Combustion Products'' has been prepared and is currently being reviewed by project team members. A final report is expected by mid-third quarter 2002. The TVA-Colbert facility has neared completion of the task to evaluate co-location of the Masada facility on the operation of the power generation facility. The TVA-Colbert fossil plant is fully capable of providing a reliable steam supply. The environmental review, preferred steam supply connection points and steam pipeline routing, and assessment of steam export impacts have been completed without major issue. A cost estimate for the steam supply system was also completed. TVA is further evaluating the impacts of adding lignin to the coal fuel blend and how the steam cost is impacted by proximity of the Masada biomass facility. TVA has provided a draft final report that is under review by team members.« less

Integrating Research into the MDE Program.

ERIC Educational Resources Information Center

Sanders, Lester E.; Lynd, Robert

1982-01-01

Examines a simulation approach to teaching selected research concepts to marketing and distributive education students and to applying these concepts to advertising layout, broadcast media advertising, retail selling, and wholesaling. (CT)

The Value of Interior Design

DTIC Science & Technology

1994-05-01

DTIC NWL2919941 The Value of Interior Design G 194 A Description of the Benefits of Applying Interior Design Principles to U.S. Army Facilities by...have considerable cost benefits . Figure 2 demonstrates the effects of specifying different furniture systems. All three layouts provide a "typical... benefit not present in the single workstation). The team approach is highly effective in reducing circulation requirements, thus increasing usable

The Low Density Matter (LDM) beamline at FERMI: optical layout and first commissioning.

PubMed

Svetina, Cristian; Grazioli, Cesare; Mahne, Nicola; Raimondi, Lorenzo; Fava, Claudio; Zangrando, Marco; Gerusina, Simone; Alagia, Michele; Avaldi, Lorenzo; Cautero, Giuseppe; de Simone, Monica; Devetta, Michele; Di Fraia, Michele; Drabbels, Marcel; Feyer, Vitaliy; Finetti, Paola; Katzy, Raphael; Kivimäki, Antti; Lyamayev, Viktor; Mazza, Tommaso; Moise, Angelica; Möller, Thomas; O'Keeffe, Patrick; Ovcharenko, Yevheniy; Piseri, Paolo; Plekan, Oksana; Prince, Kevin C; Sergo, Rudi; Stienkemeier, Frank; Stranges, Stefano; Coreno, Marcello; Callegari, Carlo

2015-05-01

The Low Density Matter (LDM) beamline has been built as part of the FERMI free-electron laser (FEL) facility to serve the atomic, molecular and cluster physics community. After the commissioning phase, it received the first external users at the end of 2012. The design and characterization of the LDM photon transport system is described, detailing the optical components of the beamline.

Microgrid Enabled Distributed Energy Solutions (MEDES) - Fort Bliss Military Reservation

DTIC Science & Technology

2014-04-01

Security Act EPA Environmental Protection Agency EPAct05 Energy Policy Act of 2005 EPDF Enlisted Personnel Dining Facility EPEC El Paso Electric Company...Retrofitting the existing electrical infrastructure was a challenge, especially with the existing switchboard layout restricting the addition of motor ...operators (to allow for load shedding). The Lockheed Martin team installed as many motor operators as physically possible in the existing

1. Photographic copy of fire alarm plan for Control and ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

1. Photographic copy of fire alarm plan for Control and Recording Center Building 4221/E-22, showing layout of rooms. California Institute of Technology, Jet Propulsion Laboratory, Plant Engineering 'Edwards Test Station, Fire Alarm Plan, Bldg. E-22,' drawing no. EFA/11-1, December 15, 1961. - Jet Propulsion Laboratory Edwards Facility, Control & Recording Center, Edwards Air Force Base, Boron, Kern County, CA

Redesign of employee cafeteria increases efficiency, satisfaction.

PubMed

Snook, I D; Levitsky, S E

1980-12-01

By streamlining the menu selection, layout, and operation of its employee cafeteria, a hospital was able to improve employee satisfaction with the service and reallocate needed resources to its inpatient food service.

"The Mother's Magazine": Moral Media for an Emergent Domestic Pedagogy, 1833-1848

ERIC Educational Resources Information Center

Schertz, Matthew Victor

2009-01-01

This paper presents a theoretical analysis of selected passages from "The Mother's Magazine", one of the first periodicals for women published in the USA. Of particular interest are selections that highlight desirable maternal characteristics and those that described the intended pedagogical experiences within the domestic sphere. The layout,…

Radiation Hardness Assurance (RHA) for Space Systems

NASA Technical Reports Server (NTRS)

Poivey, Christian; Buchner, Stephen

2007-01-01

This presentation discusses radiation hardness assurance (RHA) for space systems, providing both the programmatic aspects of RHA and the RHA procedure. RHA consists of all activities undertaken to ensure that the electronics and materials of a space system perform to their design specifications after exposure to the space radiation environment. RHA also pertains to environment definition, part selection, part testing, spacecraft layout, radiation tolerant design, and mission/system/subsystems requirements. RHA procedure consists of establishing mission requirements, defining and evaluating the radiation hazard, selecting and categorizing the appropriate parts, and evaluating circuit response to hazard. The RHA approach is based on risk management and is confined only to parts, it includes spacecraft layout, system/subsystem/circuit design, and system requirements and system operations. RHA should be taken into account in the early phases of a program including the proposal and feasibility analysis phases.

[Air quality control systems: heating, ventilating, and air conditioning (HVAC)].

PubMed

Bellucci Sessa, R; Riccio, G

2004-01-01

After a brief illustration of the principal layout schemes of Heating, Ventilating, and Air Conditioning (HVAC), the first part of this paper summarizes the standards, both voluntary and compulsory, regulating HVAC facilities design and installation with regard to the question of Indoor Air Quality (IAQ). The paper then examines the problem of ventilation systems maintenance and the essential hygienistic requirements in whose absence HVAC facilities may become a risk factor for people working or living in the building. Lastly, the paper deals with HVAC design strategies and methods, which aim not only to satisfy comfort and air quality requirements, but also to ensure easy and effective maintenance procedures.

Standing working posture compared in pregnant and non-pregnant conditions.

PubMed

Paul, J A; Frings-Dresen, M H

1994-09-01

During pregnancy, an increase in body weight occurs together with changes in body weight distribution and in fit between body dimensions and workplace layout. These changes may cause alterations in working posture which may, in turn, have adverse consequences for the biomechanical load on the musculoskeletal system and so increase the risk of musculoskeletal disorders. Using photographic posture registration, the standing working posture was studied in 27 women during the last stage of pregnancy and after delivery (the experimental group). The women performed an assembly task while standing at various workplace layouts. The postural differences between the pregnant condition and the non-pregnant condition were studied and the effect of the various workplace layouts assessed. Ten non-pregnant controls were also studied twice to establish the effect of the time interval between the measuring occasions. We found that the women of the experimental group stood further from the work surface in the pregnant condition compared to the non-pregnant condition, the hips were positioned more backwards, and, in order to reach the tesk, they increased the flexion of the trunk, increased the anteflexion of the upper arms, and extended the arms more. At the workplace layout in which the work surface height was self-selected, the postural differences due to pregnancy were smallest or even absent, compared to the postural differences in the other workplace layouts studied. Ergonomists and workers in occupational health services should be alert to the consequences for the biomechanical load on the musculoskeletal system and the risk of development of health complaints caused by postural changes due to pregnancy. An adjustable workplace layout may prevent some problems.

Improving the layout of recycling centres by use of lean production principles.

PubMed

Sundin, Erik; Björkman, Mats; Eklund, Mats; Eklund, Jörgen; Engkvist, Inga-Lill

2011-06-01

There has been increased focus on recycling in Sweden during recent years. This focus can be attributed to external environmental factors such as tougher legislation, but also to the potential gains for raw materials suppliers. Recycling centres are important components in the Swedish total recycling system. Recycling centres are manned facilities for waste collection where visitors can bring, sort and discard worn products as well as large-sized, hazardous, and electrical waste. The aim of this paper was to identify and describe the main flows and layout types at Swedish recycling centres. The aim was also to adapt and apply production theory for designing and managing recycling centre operations. More specifically, this means using lean production principles to help develop guidelines for recycling centre design and efficient control. Empirical data for this research was primarily collected through interviews and questionnaires among both visitors and employees at 16 Swedish recycling centres. Furthermore, adapted observation protocols have been used in order to explore visitor activities. There was also close collaboration with a local recycling centre company, which shared their layout experiences with the researchers in this project. The recycling centres studied had a variety of problems such as queues of visitors, overloading of material and improper sorting. The study shows that in order to decrease the problems, the recycling centres should be designed and managed according to lean production principles, i.e. through choosing more suitable layout choices with visible and linear flows, providing better visitor information, and providing suitable technical equipment. Improvements can be achieved through proper planning of the layout and control of the flow of vehicles, with the result of increased efficiency and capacity, shorter visits, and cleaner waste fractions. The benefits of a lean production mindset include increased visitor capacity, waste flexibility, improved sorting quality, shorter time for visits and improved working conditions. Copyright © 2011 Elsevier Ltd. All rights reserved.

WASTE TREATMENT BUILDING SYSTEM DESCRIPTION DOCUMENT

DOE Office of Scientific and Technical Information (OSTI.GOV)

F. Habashi

2000-06-22

The Waste Treatment Building System provides the space, layout, structures, and embedded subsystems that support the processing of low-level liquid and solid radioactive waste generated within the Monitored Geologic Repository (MGR). The activities conducted in the Waste Treatment Building include sorting, volume reduction, and packaging of dry waste, and collecting, processing, solidification, and packaging of liquid waste. The Waste Treatment Building System is located on the surface within the protected area of the MGR. The Waste Treatment Building System helps maintain a suitable environment for the waste processing and protects the systems within the Waste Treatment Building (WTB) from mostmore » of the natural and induced environments. The WTB also confines contaminants and provides radiological protection to personnel. In addition to the waste processing operations, the Waste Treatment Building System provides space and layout for staging of packaged waste for shipment, industrial and radiological safety systems, control and monitoring of operations, safeguards and security systems, and fire protection, ventilation and utilities systems. The Waste Treatment Building System also provides the required space and layout for maintenance activities, tool storage, and administrative facilities. The Waste Treatment Building System integrates waste processing systems within its protective structure to support the throughput rates established for the MGR. The Waste Treatment Building System also provides shielding, layout, and other design features to help limit personnel radiation exposures to levels which are as low as is reasonably achievable (ALARA). The Waste Treatment Building System interfaces with the Site Generated Radiological Waste Handling System, and with other MGR systems that support the waste processing operations. The Waste Treatment Building System interfaces with the General Site Transportation System, Site Communications System, Site Water System, MGR Site Layout, Safeguards and Security System, Site Radiological Monitoring System, Site Electrical Power System, Site Compressed Air System, and Waste Treatment Building Ventilation System.« less

New Baseline Design of the ILC RTML System

DOE Office of Scientific and Technical Information (OSTI.GOV)

Seletskiy, S.; Kapin, V. V.; Solyak, N.

2012-05-01

The new ILC baseline was proposed in 2009 (Strawman baseline - SB2009) to minimize cost of the machine and accommodate many changes made in the design of the accelerator systems. The biggest changes are made in the central area, where BDS, RTM L, DR, electron and positron sources are sharing the tunnels. A new layout of the compact DR and re-location of the electron and positron sources to the main tunnel requires a new lattice design for all beamlines in this area. The lattice design was coord inated between accelerator systems and Convention Facility and Siting (CFS) group to eliminatemore » conflicts between beamlines and satisfy construction requirements. In this paper we present a new design of the RTML electron and positron lattices in the centr al area and other modifications made in the RTML line to accommodate changes to the beamline layouts.« less

The NuMAX Long Baseline Neutrino Factory Concept

DOE Office of Scientific and Technical Information (OSTI.GOV)

Delahaye, J-P.; Ankenbrandt, C.; Bogacz, A.

A Neutrino Factory where neutrinos of all species are produced in equal quantities by muon decay is described as a facility at the intensity frontier for exquisite precision providing ideal conditions for ultimate neutrino studies and the ideal complement to Long Baseline Facilities like LBNF at Fermilab. It is foreseen to be built in stages with progressively increasing complexity and performance, taking advantage of existing or proposed facilities at an existing laboratory like Fermilab. A tentative layout based on a recirculating linac providing opportunities for considerable saving is discussed as well as its possible evolution toward a muon collider ifmore » and when requested by Physics. Tentative parameters of the various stages are presented as well as the necessary R&D to address the technological issues and demonstrate their feasibility.« less

The NuMAX Long Baseline Neutrino Factory concept

DOE PAGES

Delahaye, J-P.; Ankenbrandt, C. M.; Bogacz, S. A.; ...

2018-06-01

A Neutrino Factory where neutrinos of all species are produced in equal quantities by muon decay is described as a facility at the intensity frontier for exquisite precision providing ideal conditions for ultimate neutrino studies and the ideal complement to Long Baseline Facilities like LBNF at Fermilab. It is foreseen to be built in stages with progressively increasing complexity and performance, taking advantage of existing or proposed facilities at an existing laboratory like Fermilab. A tentative layout based on a recirculating linac providing opportunities for considerable saving is discussed as well as its possible evolution toward a muon collider ifmore » and when requested by Physics. Tentative parameters of the various stages are presented as well as the necessary R&D to address the technological issues and demonstrate their feasibility.« less

The NuMAX Long Baseline Neutrino Factory concept

DOE Office of Scientific and Technical Information (OSTI.GOV)

Delahaye, J-P.; Ankenbrandt, C. M.; Bogacz, S. A.

A Neutrino Factory where neutrinos of all species are produced in equal quantities by muon decay is described as a facility at the intensity frontier for exquisite precision providing ideal conditions for ultimate neutrino studies and the ideal complement to Long Baseline Facilities like LBNF at Fermilab. It is foreseen to be built in stages with progressively increasing complexity and performance, taking advantage of existing or proposed facilities at an existing laboratory like Fermilab. A tentative layout based on a recirculating linac providing opportunities for considerable saving is discussed as well as its possible evolution toward a muon collider ifmore » and when requested by Physics. Tentative parameters of the various stages are presented as well as the necessary R&D to address the technological issues and demonstrate their feasibility.« less

The NuMAX Long Baseline Neutrino Factory Concept

DOE PAGES

Delahaye, J-P.; Ankenbrandt, C.; Bogacz, A.; ...

2018-06-12

A Neutrino Factory where neutrinos of all species are produced in equal quantities by muon decay is described as a facility at the intensity frontier for exquisite precision providing ideal conditions for ultimate neutrino studies and the ideal complement to Long Baseline Facilities like LBNF at Fermilab. It is foreseen to be built in stages with progressively increasing complexity and performance, taking advantage of existing or proposed facilities at an existing laboratory like Fermilab. A tentative layout based on a recirculating linac providing opportunities for considerable saving is discussed as well as its possible evolution toward a muon collider ifmore » and when requested by Physics. Tentative parameters of the various stages are presented as well as the necessary R&D to address the technological issues and demonstrate their feasibility.« less

Orbit Transfer Rocket Engine Technology Program. Task C.5. Enhanced Heat Transfer Combustor Technology

DTIC Science & Technology

1991-12-01

December, 1991 i--" NASA-Lewis Research Center Cleveland, Ohio 44135 94-08573 Contract No. NAS3-23773 .0l•!ill~• 111 l94 3 16 09V PISULATIXI NOTICI... 3 3.1 Test Hardware and Facility Description...V - Drawings and Layouts of Calorimeter Insert and Related Hardware .... 133 - Ui - FIGURES NUMBER PIALE GE 3 -1 Integrated Component Evaluator (I.C.E

38. Photograph of a line drawing. 'PART III, SECTION 1, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

38. Photograph of a line drawing. 'PART III, SECTION 1, EQUIPMENT LAYOUT, BUILDINGS G-1 TO G-10 INCL., PURIFICATION, MANUFACTURING AREA, PLAN 'B'.' From U.S. Army Corps of Engineers. Industrial Facilities Inventory, Holston Ordnance Works, Kingsport, Tennessee. Plant B, Parts II, III. (Nashville, TN: Office of District Engineer, 1944). - Holston Army Ammunition Plant, RDX-and-Composition-B Manufacturing Line 9, Kingsport, Sullivan County, TN

The Low Density Matter (LDM) beamline at FERMI: optical layout and first commissioning

PubMed Central

Svetina, Cristian; Grazioli, Cesare; Mahne, Nicola; Raimondi, Lorenzo; Fava, Claudio; Zangrando, Marco; Gerusina, Simone; Alagia, Michele; Avaldi, Lorenzo; Cautero, Giuseppe; de Simone, Monica; Devetta, Michele; Di Fraia, Michele; Drabbels, Marcel; Feyer, Vitaliy; Finetti, Paola; Katzy, Raphael; Kivimäki, Antti; Lyamayev, Viktor; Mazza, Tommaso; Moise, Angelica; Möller, Thomas; O’Keeffe, Patrick; Ovcharenko, Yevheniy; Piseri, Paolo; Plekan, Oksana; Prince, Kevin C.; Sergo, Rudi; Stienkemeier, Frank; Stranges, Stefano; Coreno, Marcello; Callegari, Carlo

2015-01-01

The Low Density Matter (LDM) beamline has been built as part of the FERMI free-electron laser (FEL) facility to serve the atomic, molecular and cluster physics community. After the commissioning phase, it received the first external users at the end of 2012. The design and characterization of the LDM photon transport system is described, detailing the optical components of the beamline. PMID:25931066

43. Photograph of a line drawing. 'PART III, SECTION 1, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

43. Photograph of a line drawing. 'PART III, SECTION 1, EQUIPMENT LAYOUT, BUILDINGS H-1 TO H-10 INCL., GRINDING, MANUFACTURING AREA, PLANT 'B'.' From U.S. Army Corps of Engineers. Industrial Facilities Inventory, Holston Ordnance Works, Kingsport, Tennessee. Plant B, Parts II, III. (Nashville, TN: Office of the District Engineer, 1944). - Holston Army Ammunition Plant, RDX-and-Composition-B Manufacturing Line 9, Kingsport, Sullivan County, TN

Human factor design of habitable space facilities

NASA Technical Reports Server (NTRS)

Clearwater, Yvonne A.

1987-01-01

Current fundamental and applied habitability research conducted as part of the U.S. space program is reviewed with emphasis on methods, findings, and applications of the results to the planning and design of the International Space Station. The discussion covers the following six concurrent directions of habitability research: operational simulation, functional interior decor research, space crew privacy requirements, interior layout and configuration analysis, human spatial habitability model, and analogous environments research.

Royal Canadian Mounted Police National Operations Center Layout Study and Design Options

DTIC Science & Technology

2012-03-01

for the individual requirements are as follows: 1. UFC: United Facilities Criteria (Department of Defense, 2008); 2. ISO 11064: Ergonomic Design ...NOC is required to accommodate additional personnel above and beyond the existing seated capacity. As such, the proposed design needs to improve the...for Standardization. (2000). 1SO 11064 - Ergonomic Design of Control Centres. Larson, C. E., & LaFasto, F. M. (1989). Teamwork: What must go right

30. Photograph of a line drawing. 'CROSS SECTION OF PART ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

30. Photograph of a line drawing. 'CROSS SECTION OF PART III, SECTION 1, EQUIPMENT LAYOUT, BUILDINGS D-1 TO D-10 INCL., NITRATION, MANUFACTURING AREA, PLANT 'B'.' From U.S. Army Corps of Engineers. Industrial Facilities Inventory, Holston Ordnance Works, Kingsport, Tennessee. Plant B, Parts II, III. (Nashville, TN: Office of the District Engineer, 1944). - Holston Army Ammunition Plant, RDX-and-Composition-B Manufacturing Line 9, Kingsport, Sullivan County, TN

AI in manufacturing

NASA Astrophysics Data System (ADS)

Gross, John E.; Minato, Rick; Smith, David M.; Loftin, R. B.; Savely, Robert T.

1991-10-01

AI techniques are shown to have been useful in such aerospace industry tasks as vehicle configuration layouts, process planning, tool design, numerically-controlled programming of tools, production scheduling, and equipment testing and diagnosis. Accounts are given of illustrative experiences at the production facilities of three major aerospace defense contractors. Also discussed is NASA's autonomous Intelligent Computer-Aided Training System, for such ambitious manned programs as Space Station Freedom, which employs five different modules to constitute its job-independent training architecture.

Modelling Pedestrian Travel Time and the Design of Facilities: A Queuing Approach

PubMed Central

Rahman, Khalidur; Abdul Ghani, Noraida; Abdulbasah Kamil, Anton; Mustafa, Adli; Kabir Chowdhury, Md. Ahmed

2013-01-01

Pedestrian movements are the consequence of several complex and stochastic facts. The modelling of pedestrian movements and the ability to predict the travel time are useful for evaluating the performance of a pedestrian facility. However, only a few studies can be found that incorporate the design of the facility, local pedestrian body dimensions, the delay experienced by the pedestrians, and level of service to the pedestrian movements. In this paper, a queuing based analytical model is developed as a function of relevant determinants and functional factors to predict the travel time on pedestrian facilities. The model can be used to assess the overall serving rate or performance of a facility layout and correlate it to the level of service that is possible to provide the pedestrians. It has also the ability to provide a clear suggestion on the designing and sizing of pedestrian facilities. The model is empirically validated and is found to be a robust tool to understand how well a particular walking facility makes possible comfort and convenient pedestrian movements. The sensitivity analysis is also performed to see the impact of some crucial parameters of the developed model on the performance of pedestrian facilities. PMID:23691055

Methodology of shell structure reinforcement layout optimization

NASA Astrophysics Data System (ADS)

Szafrański, Tomasz; Małachowski, Jerzy; Damaziak, Krzysztof

2018-01-01

This paper presents an optimization process of a reinforced shell diffuser intended for a small wind turbine (rated power of 3 kW). The diffuser structure consists of multiple reinforcement and metal skin. This kind of structure is suitable for optimization in terms of selection of reinforcement density, stringers cross sections, sheet thickness, etc. The optimisation approach assumes the reduction of the amount of work to be done between the optimization process and the final product design. The proposed optimization methodology is based on application of a genetic algorithm to generate the optimal reinforcement layout. The obtained results are the basis for modifying the existing Small Wind Turbine (SWT) design.

Wind conditions in urban layout - Numerical and experimental research

NASA Astrophysics Data System (ADS)

Poćwierz, Marta; Zielonko-Jung, Katarzyna

2018-01-01

This paper presents research which compares the numerical and the experimental results for different cases of airflow around a few urban layouts. The study is concerned mostly with the analysis of parameters, such as pressure and velocity fields, which are essential in the building industry. Numerical simulations have been performed by the commercial software Fluent, with the use of a few different turbulence models, including popular k-ɛ, k-ɛ realizable or k-ω. A particular attention has been paid to accurate description of the conditions on the inlet and the selection of suitable computing grid. The pressure measurement near buildings and oil visualization were undertaken and described accordingly.

Re-Engineering the ISS Payload Operations Control Center During Increased Utilization and Critical Onboard Events

NASA Technical Reports Server (NTRS)

Marsh, Angela L.; Dudley, Stephanie R. B.

2014-01-01

With an increase in the utilization and hours of payload operations being executed onboard the International Space Station (ISS), upgrading the NASA Marshall Space Flight Center (MSFC) Huntsville Operations Support Center (HOSC) ISS Payload Control Area (PCA) was essential to gaining efficiencies and assurance of current and future payload health and science return. PCA houses the Payload Operations Integration Center (POIC) responsible for the execution of all NASA payloads onboard the ISS. POIC Flight Controllers are responsible for the operation of voice, stowage, command, telemetry, video, power, thermal, and environmental control in support of ISS science experiments. The methodologies and execution of the PCA refurbishment were planned and performed within a four month period in order to assure uninterrupted operation of ISS payloads and minimal impacts to payload operations teams. To vacate the PCA, three additional HOSC control rooms were reconfigured to handle ISS realtime operations, Backup Control Center (BCC) to Mission Control in Houston, simulations, and testing functions. This involved coordination and cooperation from teams of ISS operations controllers, multiple engineering and design disciplines, management, and construction companies performing an array of activities simultaneously and in sync delivering a final product with no issues that impacted the schedule. For each console operator discipline, studies of Information Technology (IT) tools and equipment layouts, ergonomics, and lines of sight were performed. Infusing some of the latest IT into the project was an essential goal in ensuring future growth and success of the ISS payload science returns. Engineering evaluations led to a state of the art media wall implementation and more efficient ethernet cabling distribution providing the latest products and the best solution for the POIC. These engineering innovations led to cost savings for the project. Constraints involved in the management of the project included executing over 450 crew-hours of ISS real-time payload operations including a major onboard communications upgrade, SpaceX un-berth, a Soyuz launch, roll-out of ISS live video and interviews from the POIC, annual BCC certification and hurricane season, and ISS simulations and testing. Continuous ISS payload operations were possible during the PCA facility modifications with the reconfiguration of four control rooms and standup of two temporary control areas. Another major restriction to the project was an ongoing facility upgrade that included a NASA Headquarters mandated replacement of all electrical and mechanical systems and replacement of an external generator. These upgrades required a facility power outage during the PCA upgrades. The project also encompassed console layout designs and ordering, amenities selections and ordering, excessing of old equipment, moves, disposal of old IT equipment, camera installations, facility tour re-schedules, and contract justifications. These were just some of the tasks needed for a successful project.

Improving the hydrocarbon production via co-pyrolysis of bagasse with bio-plastic and dual-catalysts layout.

PubMed

Zhang, Huiyan; Likun, Peter Keliona Wani; Xiao, Rui

2018-03-15

Catalytic fast pyrolysis (CFP) of bagasse and bio-plastic (chicken feather keratin) and their mixtures were conducted to produce aromatic hydrocarbons over a HZSM-5, USY, and dual-catalysts layout. The effects of temperature, co-feeding ratios, feed-to-catalyst ratios and dual catalysts on hydrocarbon yields and selectivities were investigated. The results show a general improvement in the aromatic hydrocarbons yields in all cases compared to non-catalytic and pure biomass pyrolysis. The aromatic hydrocarbons increased by 10 fold with the increase of temperature from 400°C to 700°C. The aromatic yields increased 1.5 times at co-feeding, 2.0 greater at feed/HZSM-5 ratio of 1:6, 1.2 times at feed/USY ratio of 1:16, and 2.66 times at USY/HZSM-5 scenario. The selectivities towards benzene increased, at higher co-feeding ratios, while that of toluene shows an opposite trend. Xylenes selectivities were less sensitive to the changes of co-feeding ratios. In contrast, the USY catalyst only produced little amount of toluene and xylenes. The dual catalyst design (USY/HZSM-5) resulted in the highest aromatic yields, than other catalyst design scenarios. The pyrolysis temperature is a significant parameter for hydrocarbon production. Co-feeding bagasse and bio-plastic enhanced biomass conversion to aromatic compounds. For any type of zeolite catalyst, there was an optimum feed-to-catalyst ratio that generated maximum hydrocarbons. Dual catalyst layout shows a new opportunity for efficient conversion of biomass materials into hydrocarbons. Copyright © 2017 Elsevier B.V. All rights reserved.

Guide for users of the National Transonic Facility

NASA Technical Reports Server (NTRS)

Fuller, D. E.; Gloss, B. B.; Nystrom, D.

1981-01-01

The National Transonic Facility (NTF) is a fan-driven, closed-circuit, continuous flow, pressurized wind tunnel. The test section is 2.5 m x 2.5 m and 7.62 m long with a slotted-wall configuration. The NTF will have a Mach number range from 0.2 to 1.2, with Reynolds number up to 120 10 to the sixth power at Mach 1 (based on a reference length of 0.25 m). The pressure range for the facility will be from 1 to about 9 bars (1 ban = 100 kPa), and the temperature can be varied from 340 to 78 K. This report provides potential users of the NTF with the information required for preliminary planning to test programs and for preliminary layout of models and model supports which may be used in such programs.

Deconstructing Visual Scenes in Cortex: Gradients of Object and Spatial Layout Information

PubMed Central

Kravitz, Dwight J.; Baker, Chris I.

2013-01-01

Real-world visual scenes are complex cluttered, and heterogeneous stimuli engaging scene- and object-selective cortical regions including parahippocampal place area (PPA), retrosplenial complex (RSC), and lateral occipital complex (LOC). To understand the unique contribution of each region to distributed scene representations, we generated predictions based on a neuroanatomical framework adapted from monkey and tested them using minimal scenes in which we independently manipulated both spatial layout (open, closed, and gradient) and object content (furniture, e.g., bed, dresser). Commensurate with its strong connectivity with posterior parietal cortex, RSC evidenced strong spatial layout information but no object information, and its response was not even modulated by object presence. In contrast, LOC, which lies within the ventral visual pathway, contained strong object information but no background information. Finally, PPA, which is connected with both the dorsal and the ventral visual pathway, showed information about both objects and spatial backgrounds and was sensitive to the presence or absence of either. These results suggest that 1) LOC, PPA, and RSC have distinct representations, emphasizing different aspects of scenes, 2) the specific representations in each region are predictable from their patterns of connectivity, and 3) PPA combines both spatial layout and object information as predicted by connectivity. PMID:22473894

Various supercritical carbon dioxide cycle layouts study for molten carbonate fuel cell application

NASA Astrophysics Data System (ADS)

Bae, Seong Jun; Ahn, Yoonhan; Lee, Jekyoung; Lee, Jeong Ik

2014-12-01

Various supercritical carbon dioxide (S-CO2) cycles for a power conversion system of a Molten Carbonate Fuel Cell (MCFC) hybrid system are studied in this paper. Re-Compressing Brayton (RCB) cycle, Simple Recuperated Brayton (SRB) cycle and Simple Recuperated Transcritical (SRT) cycle layouts were selected as candidates for this study. In addition, a novel concept of S-CO2 cycle which combines Brayton cycle and Rankine cycle is proposed and intensively studied with other S-CO2 layouts. A parametric study is performed to optimize the total system to be compact and to achieve wider operating range. Performances of each S-CO2 cycle are compared in terms of the thermal efficiency, net electricity of the MCFC hybrid system and approximate total volumes of each S-CO2 cycle. As a result, performance and total physical size of S-CO2 cycle can be better understood for MCFC S-CO2 hybrid system and especially, newly suggested S-CO2 cycle shows some success.

Routing channels in VLSI layout

NASA Astrophysics Data System (ADS)

Cai, Hong

A number of algorithms for the automatic routing of interconnections in Very Large Scale Integration (VLSI) building-block layouts are presented. Algorithms for the topological definition of channels, the global routing and the geometrical definition of channels are presented. In contrast to traditional approaches the definition and ordering of the channels is done after the global routing. This approach has the advantage that global routing information can be taken into account to select the optimal channel structure. A polynomial algorithm for the channel definition and ordering problem is presented. The existence of a conflict-free channel structure is guaranteed by enforcing a sliceable placement. Algorithms for finding the shortest connection path are described. A separate algorithm is developed for the power net routing, because the two power nets must be planarly routed with variable wire width. An integrated placement and routing system for generating building-block layout is briefly described. Some experimental results and design experiences in using the system are also presented. Very good results are obtained.

Underground Architecture and Layout for the Belgian High-Level and Long-Lived Intermediate-Level Radioactive Waste Disposal Facility- 12116

DOE Office of Scientific and Technical Information (OSTI.GOV)

Van Cotthem, Alain; Van Humbeeck, Hughes; Biurrun, Enrique

The underground architecture and layout of the proposed Belgian high-level (HLW) and long-lived, intermediate-level radioactive wastes (ILW-LL) disposal system (repository) is mainly based on lessons learned during the development and 30-year-long operation of an underground research laboratory (URL) ('HADES') located adjacent to the city of Mol at a depth of 225 m in a 100-m-thick, Tertiary clay formation; the Boom clay. The following main operational and safety challenges are addressed in the proposed architecture and layout: 1. Following excavation, the underground openings needed to be promptly supported to minimize the extent of the excavation damaged zone (EDZ). 2. The sizemore » and unsupported stand-up time at tunnel crossings/intersections also needed to be minimized to minimize the extent of the related EDZ. 3. Steel components had to be minimized to limit the related long-term (post-closure) corrosion and hydrogen production. 4. The shafts and all equipment had to go down through a 180-m-thick aquifer and handle up to 65-Ton payloads. 5. The shaft seals had to be placed in the underlying clay layer. The currently proposed layout minimizes the excavated volume based on strict long-term-safety criteria and optimizes operational safety. Operational safety is further enhanced by a remote-controlled waste-package-handling system transporting the waste packages from their respective surface location down to their respective disposal location with no intermediate operation. The related on-site preparation and thenceforth use of cement-based, waste package- transportation containers are integral operational-safety components. In addition to strengthening the waste packages and providing radiation protection, these containers also provide long-term corrosion protection of the internal 'primary' steel packages. (authors)« less

[Land layout for lake tourism based on ecological restraint].

PubMed

Wang, Jian-Ying; Li, Jiang-Feng; Zou, Li-Lin; Liu, Shi-Bin

2012-10-01

To avoid the decrease and deterioration of lake wetlands and the other ecological issues such as lake water pollution that were caused by the unreasonable exploration of lake tourism, a land layout for the tourism development of Liangzi Lake with the priority of ecological security pattern was proposed, based on the minimal cumulative resistance model and by using GIS technology. The study area was divided into four ecological function zones, i. e., core protection zone, ecological buffer zone, ecotone zone, and human activity zone. The core protection zone was the landscape region of ecological source. In the protection zone, new tourism land was forbidden to be increased, and some of the existing fundamental tourism facilities should be removed while some of them should be upgraded. The ecological buffer zone was the landscape region with resistance value ranged from 0 to 4562. In the buffer zone, expansion of tourism land should be forbidden, the existing tourism land should be downsized, and human activities should be isolated from ecological source by converting the human environment to the natural environment as far as possible. The ecotone zone was the landscape region with resistance value ranged from 4562 to 30797. In this zone, the existing tourism land was distributed in patches, tourism land could be expanded properly, and the lake forestry ecological tourism should be developed widely. The human activity zone was the landscape region with resistance value ranged from 30797 to 97334, which would be the key area for the land layout of lake tourism. It was suggested that the land layout for tourism with the priority of landscape ecological security pattern would be the best choice for the lake sustainable development.

Clear & Simple

MedlinePlus

... page factsheet, a 10-page booklet, or a series of short factsheets delivered at different points in the learning process. Budget and target audience information help shape decisions about the length and scope of the product. Design questions include photo and graphics selection, layout and ...

Design of dental surgeries in relation to instrument decontamination.

PubMed

Smith, A J; Lockhart, D E A; McDonald, E; Creanor, S; Hurrell, D; Bagg, J

2010-12-01

Recent guidelines advise that the decontamination of dental instruments should be undertaken outwith the treatment area. The aim of this study was to determine the physical area of rooms in dental surgeries that decontaminate instruments within and outwith the treatment area respectively, and other factors relating to practice layout and ventilation. Data were collected by interview and observation of dental healthcare workers in dental practice in Scotland, UK. Room layouts were recorded and measured at floor, benchtop and above benchtop heights. Thirteen surgeries with instrument decontamination processes occurring in the treatment area and seven surgeries with instrument decontamination outwith the treatment area were selected at random for detailed analysis of room dimensions. Of the 179 dental surgeries surveyed, 55% were located in converted residential premises and most practitioners (91%) did not share premises with other healthcare providers. The median number of rooms in the practices was 8 (range: 2-21) and the median number of surgeries present was 3 (range: 1-6). Regardless of whether instrument decontamination facilities were housed within the treatment area or not, the average treatment area room size for both was 15.8m(2) (range: 7.3-23.9) (P=0.862), with 20% of the room area available as work surfaces. The median size of the seven instrument decontamination rooms (local decontamination units) was 7.6m(2) (range: 2.9-16.0), with, on average, 63% of the room used for work surfaces. This survey suggests that the historical location of dental surgeries in converted residential properties places many restrictions on appropriate design for healthcare premises. Copyright © 2010 The Hospital Infection Society. Published by Elsevier Ltd. All rights reserved.

Replenishable food supply on Mars

NASA Technical Reports Server (NTRS)

1990-01-01

The design team's present objective is to design a facility which will provide an environment to grow plants on the surface of Mars for a continuous supply of food for a ten-man crew. The main focus of the project is the design of a greenhouse. Concentration of the current design effort is on the outer structure, internal layout, and construction methods. The project was conducted by undergraduate students at Prairie View A&M University during Fall 1989 and Spring 1990.

Extraterrestrial processing and manufacturing of large space systems, volume 1, chapters 1-6

NASA Technical Reports Server (NTRS)

Miller, R. H.; Smith, D. B. S.

1979-01-01

Space program scenarios for production of large space structures from lunar materials are defined. The concept of the space manufacturing facility (SMF) is presented. The manufacturing processes and equipment for the SMF are defined and the conceptual layouts are described for the production of solar cells and arrays, structures and joints, conduits, waveguides, RF equipment radiators, wire cables, and converters. A 'reference' SMF was designed and its operation requirements are described.

GUINEVERE experiment: Kinetic analysis of some reactivity measurement methods by deterministic and Monte Carlo codes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bianchini, G.; Burgio, N.; Carta, M.

The GUINEVERE experiment (Generation of Uninterrupted Intense Neutrons at the lead Venus Reactor) is an experimental program in support of the ADS technology presently carried out at SCK-CEN in Mol (Belgium). In the experiment a modified lay-out of the original thermal VENUS critical facility is coupled to an accelerator, built by the French body CNRS in Grenoble, working in both continuous and pulsed mode and delivering 14 MeV neutrons by bombardment of deuterons on a tritium-target. The modified lay-out of the facility consists of a fast subcritical core made of 30% U-235 enriched metallic Uranium in a lead matrix. Severalmore » off-line and on-line reactivity measurement techniques will be investigated during the experimental campaign. This report is focused on the simulation by deterministic (ERANOS French code) and Monte Carlo (MCNPX US code) calculations of three reactivity measurement techniques, Slope ({alpha}-fitting), Area-ratio and Source-jerk, applied to a GUINEVERE subcritical configuration (namely SC1). The inferred reactivity, in dollar units, by the Area-ratio method shows an overall agreement between the two deterministic and Monte Carlo computational approaches, whereas the MCNPX Source-jerk results are affected by large uncertainties and allow only partial conclusions about the comparison. Finally, no particular spatial dependence of the results is observed in the case of the GUINEVERE SC1 subcritical configuration. (authors)« less

Generation of Spatially Aligned Collagen Fiber Networks through Microtransfer Molding

PubMed Central

Naik, Nisarga; Caves, Jeffrey

2013-01-01

The unique biomechanical properties of native tissue are governed by the organization and composition of integrated collagen and elastin networks. We report an approach for fabricating spatially aligned, fiber-reinforced composites (FRC) with adjustable collagen fiber dimensions, layouts, and distribution within an elastin-like protein matrix yielding a biocomposite with controllable mechanical responses. Microtransfer molding is employed for the fabrication of hollow and solid collagen fibers with straight or crimped fiber geometries. Collagen fibers (width: 2 – 50 μm, thickness: 300 nm – 3 μm) exhibit a Young’s modulus of 126 ± 61 MPa and an ultimate tensile strength (UTS) of 7 ± 3.2 MPa. As fiber networks within composite structures, straight fiber layouts display orthotropic responses with Young’s modulus ranging from 0.95 ± 0.35 to 10.4 ± 0.5 MPa and tensile strength from 0.22 ± 0.08 to 0.87 ± 0.5 MPa with increasing fraction of collagen fibers (1–10% v/v). In contrast, composites based on crimped fiber layouts exhibit strain-dependent stiffness with an increase in Young’s modulus from 0.7 ± 0.14 MPa to 3.15 ± 0.49 MPa, at a specific transition strain. Through controlling the microstructure of engineered collagen fiber networks, a facile means has been established to control macroscale mechanical responses of composite protein-based materials. PMID:24039146

Optimization of site layout for change of plant operation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Reuwer, S.M.; Kasperski, E.; Joseph, T.D.

1995-12-31

Several of the Florida Power & Light operating fossil power plants have undergone significant site layout changes as well as changes in plant operation. The FPL Fort Lauderdale Plant was repowered in 1992 which consisted of using four (4) Westinghouse 501F Combustion Turbines rated at 158 Mw each, to repower two (2) existing steam turbines rates at 143 Mw each. In 1991, a physical security fence separation occurred between Turkey Point Plants`s fossil fueled Units 1&2, and its nuclear fueled Units 3&4. As a result of this separation, certain facilities common to both the nuclear side and fossil side ofmore » the plant required relocating. Also, the Sanford and Manatee Plants were evaluated for the use of a new fuel as an alternative source. Manatee Plant is currently in the licensing process for modifications to burn a new fuel, requiring expansion of backened clean-up equipment, with additional staff to operate this equipment. In order to address these plant changes, site development studies were prepared for each plant to determine the suitability of the existing ancillary facilities to support the operational changes, and to make recommendations for facility improvement if found inadequate. A standardized process was developed for all of the site studies. This proved to be a comprehensive process and approach, that gave FPL a successful result that all the various stake holders bought into. This process was objectively based, focused, and got us to where we need to be as quickly as possible. As a result, this paper details the outline and various methods developed to prepare a study following this process, that will ultimately provide the optimum site development plan for the changing plant operations.« less

On the suitability and development of layout templates for analog layout reuse and layout-aware synthesis

NASA Astrophysics Data System (ADS)

Castro-Lopez, Rafael; Fernandez, Francisco V.; Rodriguez Vazquez, Angel

2005-06-01

Accelerating the synthesis of increasingly complex analog integrated circuits is key to bridge the widening gap between what we can integrate and what we can design while meeting ever-tightening time-to-market constraints. It is a well-known fact in the semiconductor industry that such goal can only be attained by means of adequate CAD methodologies, techniques, and accompanying tools. This is particularly important in analog physical synthesis (a.k.a. layout generation), where large sensitivities of the circuit performances to the many subtle details of layout implementation (device matching, loading and coupling effects, reliability, and area features are of utmost importance to analog designers), render complete automation a truly challenging task. To approach the problem, two directions have been traditionally considered, knowledge-based and optimization-based, both with their own pros and cons. Besides, recently reported solutions oriented to speed up the overall design flow by means of reuse-based practices or by cutting off time-consuming, error-prone spins between electrical and layout synthesis (a technique known as layout-aware synthesis), rely on a outstandingly rapid yet efficient layout generation method. This paper analyses the suitability of procedural layout generation based on templates (a knowledge-based approach) by examining the requirements that both layout reuse and layout-aware solutions impose, and how layout templates face them. The ability to capture the know-how of experienced layout designers and the turnaround times for layout instancing are considered main comparative aspects in relation to other layout generation approaches. A discussion on the benefit-cost trade-off of using layout templates is also included. In addition to this analysis, the paper delves deeper into systematic techniques to develop fully reusable layout templates for analog circuits, either for a change of the circuit sizing (i.e., layout retargeting) or a change of the fabrication process (i.e., layout migration). Several examples implemented with the Cadence's Virtuoso tool suite are provided as demonstration of the paper's contributions.

Improving mobile robot localization: grid-based approach

NASA Astrophysics Data System (ADS)

Yan, Junchi

2012-02-01

Autonomous mobile robots have been widely studied not only as advanced facilities for industrial and daily life automation, but also as a testbed in robotics competitions for extending the frontier of current artificial intelligence. In many of such contests, the robot is supposed to navigate on the ground with a grid layout. Based on this observation, we present a localization error correction method by exploring the geometric feature of the tile patterns. On top of the classical inertia-based positioning, our approach employs three fiber-optic sensors that are assembled under the bottom of the robot, presenting an equilateral triangle layout. The sensor apparatus, together with the proposed supporting algorithm, are designed to detect a line's direction (vertical or horizontal) by monitoring the grid crossing events. As a result, the line coordinate information can be fused to rectify the cumulative localization deviation from inertia positioning. The proposed method is analyzed theoretically in terms of its error bound and also has been implemented and tested on a customary developed two-wheel autonomous mobile robot.

LAFD: TA-55 General Facility Familiarization Tour, Course #55261

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rutherford, Victor Stephen; Miller, Joshua; Mason, Robert Clifford

Los Alamos National Laboratory (LANL) will conduct familiarization tours for personnel of the Los Alamos County Fire Department (LAFD) at the TA-55 General Facility. These familiarization tours are official LANL business; the purpose of these tours is to orient LAFD firefighters to the facility so that they can respond efficiently and quickly to a variety of emergency situations. This orientation includes, among other topics, ingress and egress of the area and buildings, layout and organization of the facility, evacuation procedures and assembly points, and areas of concern within the various buildings at the facility. LAFD firefighters have the skills andmore » abilities to perform firefighting operations and other emergency response tasks that cannot be provided by LANL personnel who have the required clearance level. This handout provides details of the information, along with maps and diagrams, to be presented during the familiarization tours. The handout will be distributed to the trainees at the time of the tour. A corresponding checklist will also be used as guidance during the familiarization tours to ensure that all required information is presented to LAFD personnel.« less

Status of the LBNF Cryogenic System

DOE PAGES

Montanari, D.; Adamowski, M.; Bremer, J.; ...

2017-12-30

We present that the Sanford Underground Research Facility (SURF) will host the Deep Underground Neutrino Experiment (DUNE), an international multi-kiloton Long-Baseline neutrino experiment that will be installed about a mile underground in Lead, SD. In the current configuration four cryostats will contain a modular detector and a total of 68,400 tons of ultrapure liquid argon, with a level of impurities lower than 100 parts per trillion of oxygen equivalent contamination. The Long-Baseline Neutrino Facility (LBNF) provides the conventional facilities and the cryogenic infrastructure to support DUNE. The system is comprised of three sub-systems: External/Infrastructure, Proximity and Internal cryogenics. An internationalmore » engineering team will design, manufacture, commission, and qualify the LBNF cryogenic system. This contribution presents the modes of operations, layout and main features of the LBNF cryogenic system. Lastly, the expected performance, the functional requirements and the status of the design are also highlighted.« less

Status of the LBNF Cryogenic System

DOE Office of Scientific and Technical Information (OSTI.GOV)

Montanari, D.; Adamowski, M.; Bremer, J.

We present that the Sanford Underground Research Facility (SURF) will host the Deep Underground Neutrino Experiment (DUNE), an international multi-kiloton Long-Baseline neutrino experiment that will be installed about a mile underground in Lead, SD. In the current configuration four cryostats will contain a modular detector and a total of 68,400 tons of ultrapure liquid argon, with a level of impurities lower than 100 parts per trillion of oxygen equivalent contamination. The Long-Baseline Neutrino Facility (LBNF) provides the conventional facilities and the cryogenic infrastructure to support DUNE. The system is comprised of three sub-systems: External/Infrastructure, Proximity and Internal cryogenics. An internationalmore » engineering team will design, manufacture, commission, and qualify the LBNF cryogenic system. This contribution presents the modes of operations, layout and main features of the LBNF cryogenic system. Lastly, the expected performance, the functional requirements and the status of the design are also highlighted.« less

Status of the LBNF Cryogenic System

DOE Office of Scientific and Technical Information (OSTI.GOV)

Montanari, D.; Adamowski, M.; Bremer, J.

2017-01-01

The Sanford Underground Research Facility (SURF) will host the Deep Underground Neutrino Experiment (DUNE), an international multi-kiloton Long-Baseline neutrino experiment that will be installed about a mile underground in Lead, SD. In the current configuration four cryostats will contain a modular detector and a total of 68,400 ton of ultrapure liquid argon, with a level of impurities lower than 100 parts per trillion of oxygen equivalent contamination. The Long-Baseline Neutrino Facility (LBNF) provides the conventional facilities and the cryogenic infrastructure to support DUNE. The system is comprised of three sub-systems: External/Infrastructure, Proximity and Internal cryogenics. An international engineering team willmore » design, manufacture, commission, and qualify the LBNF cryogenic system. This contribution presents the models of operations, layout and main features of the LBNF cryogenic system. The expected performance, the functional requirements and the status of the design are also highlighted.« less

Acoustic facilities for human factors research at NASA Langley Research Center: Description and operational capabilities

NASA Astrophysics Data System (ADS)

Hubbard, H. H.; Powell, C. A.

1981-06-01

A number of facilities were developed which provide a unique test capability for psychoacoustics and related human factors research. The design philosophy, physical layouts, dimensions, construction features, operating capabilities, and example applications for these facilities are described. In the exterior effects room, human subjects are exposed to the types of noises that are experienced outdoors, and in the interior effects room, subjects are exposed to the types of noises and noise-induced vibrations that are experience indoors. Subjects are also exposed to noises in an echo-free environment in the anechoic listening room. An aircraft noise synthesis system, which simulates aircraft flyover noise at an observer position on the ground, is used in conjunction with these three rooms. The passenger ride quality apparatus, a device for studying passenger response to noise and vibration in aircraft, or in other vehicles, is described.

Overview of an Indoor Sonic Boom Simulator at NASA Langley Research Center

NASA Technical Reports Server (NTRS)

Klos, Jacob

2012-01-01

A facility has been constructed at NASA Langley Research Center to simulate the soundscape inside residential houses that are exposed to environmental noise from aircraft. This controllable indoor listening environment, the Interior Effects Room, enables systematic study of parameters that affect psychoacoustic response. The single-room facility, built using typical residential construction methods and materials, is surrounded on adjacent sides by two arrays of loudspeakers in close proximity to the exterior walls. The arrays, containing 52 subwoofers and 52 mid-range speakers, have a usable bandwidth of 3 Hz to 5 kHz and sufficient output to allow study of sonic boom noise. In addition to these exterior arrays, satellite speakers placed inside the room are used to augment the transmitted sound with rattle and other audible contact ]induced noise that can result from low frequency excitation of a residential house. The layout of the facility, operational characteristics, acoustic characteristics and equalization approaches are summarized.

Status of the LBNF Cryogenic System

NASA Astrophysics Data System (ADS)

Montanari, D.; Adamowski, M.; Bremer, J.; Delaney, M.; Diaz, A.; Doubnik, R.; Haaf, K.; Hentschel, S.; Norris, B.; Voirin, E.

2017-12-01

The Sanford Underground Research Facility (SURF) will host the Deep Underground Neutrino Experiment (DUNE), an international multi-kiloton Long-Baseline neutrino experiment that will be installed about a mile underground in Lead, SD. In the current configuration four cryostats will contain a modular detector and a total of 68,400 tons of ultrapure liquid argon, with a level of impurities lower than 100 parts per trillion of oxygen equivalent contamination. The Long-Baseline Neutrino Facility (LBNF) provides the conventional facilities and the cryogenic infrastructure to support DUNE. The system is comprised of three sub-systems: External/Infrastructure, Proximity and Internal cryogenics. An international engineering team will design, manufacture, commission, and qualify the LBNF cryogenic system. This contribution presents the modes of operations, layout and main features of the LBNF cryogenic system. The expected performance, the functional requirements and the status of the design are also highlighted.

Acoustic facilities for human factors research at NASA Langley Research Center: Description and operational capabilities

NASA Technical Reports Server (NTRS)

Hubbard, H. H.; Powell, C. A.

1981-01-01

A number of facilities were developed which provide a unique test capability for psychoacoustics and related human factors research. The design philosophy, physical layouts, dimensions, construction features, operating capabilities, and example applications for these facilities are described. In the exterior effects room, human subjects are exposed to the types of noises that are experienced outdoors, and in the interior effects room, subjects are exposed to the types of noises and noise-induced vibrations that are experience indoors. Subjects are also exposed to noises in an echo-free environment in the anechoic listening room. An aircraft noise synthesis system, which simulates aircraft flyover noise at an observer position on the ground, is used in conjunction with these three rooms. The passenger ride quality apparatus, a device for studying passenger response to noise and vibration in aircraft, or in other vehicles, is described.

User-friendly design approach for analog layout design

NASA Astrophysics Data System (ADS)

Li, Yongfu; Lee, Zhao Chuan; Tripathi, Vikas; Perez, Valerio; Ong, Yoong Seang; Hui, Chiu Wing

2017-03-01

Analog circuits are sensitives to the changes in the layout environment conditions, manufacturing processes, and variations. This paper presents analog verification flow with five types of analogfocused layout constraint checks to assist engineers in identifying any potential device mismatch and layout drawing mistakes. Compared to several solutions, our approach only requires layout design, which is sufficient to recognize all the matched devices. Our approach simplifies the data preparation and allows seamless integration into the layout environment with minimum disruption to the custom layout flow. Our user-friendly analog verification flow provides the engineer with more confident with their layouts quality.

42. Photograph of a line drawing. 'CROSS SECTION AND PLAN ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

42. Photograph of a line drawing. 'CROSS SECTION AND PLAN LAYOUT OF PART I, SECTION 8, BUILDINGS NO. H-1 TO H-10 INCL., GRINDING, MANUFACTURING AREA, PLANT B AS OF 4-24-44.' From the U.S. Army Corps of Engineers. Industrial Facilities Inventory, Holston Ordnance Works, Kingsport, Tennessee. Plant B, Parts II, III. (NashVille, TN: Office of the District Engineer, 1944). - Holston Army Ammunition Plant, RDX-and-Composition-B Manufacturing Line 9, Kingsport, Sullivan County, TN

29. Photograph of a line drawing. 'CROSS SECTION AND PLAN ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

29. Photograph of a line drawing. 'CROSS SECTION AND PLAN LAYOUT OF PART I, SECTION 8, BUILDINGS NO. D-1 TO D-10 INCL., NITRATION, MANUFACTURING AREA, PLANT B AS OF 4-24-44.' From the U.S. Army Corps of Engineers. Industrial Facilities Inventory, Holston Ordnance Works, Kingsport, Tennessee. Plant B, Parts II, III. (Nashville, TN: Office of the District Engineer, 1944). - Holston Army Ammunition Plant, RDX-and-Composition-B Manufacturing Line 9, Kingsport, Sullivan County, TN

Predicting the effect of seine rope layout pattern and haul-in procedure on the effectiveness of demersal seine fishing: A Computer simulation-based approach.

PubMed

Madsen, Nina A H; Aarsæther, Karl G; Herrmann, Bent

2017-01-01

Demersal Seining is an active fishing method applying two long seine ropes and a seine net. Demersal seining relies on fish responding to the seine rope as it moves during the fishing process. The seine ropes and net are deployed in a specific pattern encircling an area on the seabed. In some variants of demersal seining the haul-in procedure includes a towing phase where the fishing vessel moves forward before starting to winch in the seine ropes. The initial seine rope encircled area, the gradual change in it during the haul-in process and the fish's reaction to the moving seine ropes play an important role in the catch performance of demersal seine fishing. The current study investigates this subject by applying computer simulation models for demersal seine fishing. The demersal seine fishing is dynamic in nature and therefore a dynamic model, SeineSolver is applied for simulating the physical behaviour of the seine ropes during the fishing process. Information about the seine rope behaviour is used as input to another simulation tool, SeineFish that predicts the catch performance of the demersal seine fishing process. SeineFish implements a simple model for how fish at the seabed reacts to an approaching seine rope. Here, the SeineSolver and SeineFish tools are applied to investigate catching performance for a Norwegian demersal seine fishery targeting cod (Gadus morhua) in the coastal zone. The effect of seine rope layout pattern and the duration of the towing phase are investigated. Among the four different layout patterns investigated, the square layout pattern was predicted to perform best; catching 69%-86% more fish than would be obtained with the rectangular layout pattern. Inclusion of a towing phase in the fishing process was found to increase the catch performance for all layout patterns. For the square layout pattern, inclusion of a towing phase of 15 or 35 minutes increased the catch performance by respectively 37% and 48% compared to fishing without a towing phase. These results highlights the importance of the selected seine rope layout pattern and the duration of the towing phase when fishermen try to maximize the catch performance of their fishery. To our knowledge this is the first time the combination of models for the physical behaviour of seine ropes and for fish behaviour in response to seine rope movements have been applied to predict catch performance for demersal seining.

Predicting the effect of seine rope layout pattern and haul-in procedure on the effectiveness of demersal seine fishing: A Computer simulation-based approach

PubMed Central

Madsen, Nina A. H.; Aarsæther, Karl G.; Herrmann, Bent

2017-01-01

Demersal Seining is an active fishing method applying two long seine ropes and a seine net. Demersal seining relies on fish responding to the seine rope as it moves during the fishing process. The seine ropes and net are deployed in a specific pattern encircling an area on the seabed. In some variants of demersal seining the haul-in procedure includes a towing phase where the fishing vessel moves forward before starting to winch in the seine ropes. The initial seine rope encircled area, the gradual change in it during the haul-in process and the fish's reaction to the moving seine ropes play an important role in the catch performance of demersal seine fishing. The current study investigates this subject by applying computer simulation models for demersal seine fishing. The demersal seine fishing is dynamic in nature and therefore a dynamic model, SeineSolver is applied for simulating the physical behaviour of the seine ropes during the fishing process. Information about the seine rope behaviour is used as input to another simulation tool, SeineFish that predicts the catch performance of the demersal seine fishing process. SeineFish implements a simple model for how fish at the seabed reacts to an approaching seine rope. Here, the SeineSolver and SeineFish tools are applied to investigate catching performance for a Norwegian demersal seine fishery targeting cod (Gadus morhua) in the coastal zone. The effect of seine rope layout pattern and the duration of the towing phase are investigated. Among the four different layout patterns investigated, the square layout pattern was predicted to perform best; catching 69%-86% more fish than would be obtained with the rectangular layout pattern. Inclusion of a towing phase in the fishing process was found to increase the catch performance for all layout patterns. For the square layout pattern, inclusion of a towing phase of 15 or 35 minutes increased the catch performance by respectively 37% and 48% compared to fishing without a towing phase. These results highlights the importance of the selected seine rope layout pattern and the duration of the towing phase when fishermen try to maximize the catch performance of their fishery. To our knowledge this is the first time the combination of models for the physical behaviour of seine ropes and for fish behaviour in response to seine rope movements have been applied to predict catch performance for demersal seining. PMID:28771583

Economics of Soil Disturbance

Treesearch

Han-Sup Han

2007-01-01

Economic implications of soil disturbance are discussed in four categories: planning and layout, selection of harvesting systems and equipment, long-term site productivity loss, and rehabilitation treatments. Preventive measures are more effective in minimizing impacts on soils than rehabilitation treatments because of the remedial expenses, loss of productivity until...

Generalization of the photo process window and its application to OPC test pattern design

NASA Astrophysics Data System (ADS)

Eisenmann, Hans; Peter, Kai; Strojwas, Andrzej J.

2003-07-01

From the early development phase up to the production phase, test pattern play a key role for microlithography. The requirement for test pattern is to represent the design well and to cover the space of all process conditions, e.g. to investigate the full process window and all other process parameters. This paper shows that the current state-of-the-art test pattern do not address these requirements sufficiently and makes suggestions for a better selection of test pattern. We present a new methodology to analyze an existing layout (e.g. logic library, test pattern or full chip) for critical layout situations which does not need precise process data. We call this method "process space decomposition", because it is aimed at decomposing the process impact to a layout feature into a sum of single independent contributions, the dimensions of the process space. This is a generalization of the classical process window, which examines defocus and exposure dependency of given test pattern, e.g. CD value of dense and isolated lines. In our process space we additionally define the dimensions resist effects, etch effects, mask error and misalignment, which describe the deviation of the printed silicon pattern from its target. We further extend it by the pattern space using a product based layout (library, full chip or synthetic test pattern). The criticality of pattern is defined by their deviation due to aerial image, their sensitivity to the respective dimension or several combinations of these. By exploring the process space for a given design, the method allows to find the most critical patterns independent of specific process parameters. The paper provides examples for different applications of the method: (1) selection of design oriented test pattern for lithography development (2) test pattern reduction in process characterization (3) verification/optimization of printability and performance of post processing procedures (like OPC) (4) creation of a sensitive process monitor.

Acoustic-tactile rendering of visual information

NASA Astrophysics Data System (ADS)

Silva, Pubudu Madhawa; Pappas, Thrasyvoulos N.; Atkins, Joshua; West, James E.; Hartmann, William M.

2012-03-01

In previous work, we have proposed a dynamic, interactive system for conveying visual information via hearing and touch. The system is implemented with a touch screen that allows the user to interrogate a two-dimensional (2-D) object layout by active finger scanning while listening to spatialized auditory feedback. Sound is used as the primary source of information for object localization and identification, while touch is used both for pointing and for kinesthetic feedback. Our previous work considered shape and size perception of simple objects via hearing and touch. The focus of this paper is on the perception of a 2-D layout of simple objects with identical size and shape. We consider the selection and rendition of sounds for object identification and localization. We rely on the head-related transfer function for rendering sound directionality, and consider variations of sound intensity and tempo as two alternative approaches for rendering proximity. Subjective experiments with visually-blocked subjects are used to evaluate the effectiveness of the proposed approaches. Our results indicate that intensity outperforms tempo as a proximity cue, and that the overall system for conveying a 2-D layout is quite promising.

Design of hydrogen vent line for the cryogenic hydrogen system in J-PARC

NASA Astrophysics Data System (ADS)

Tatsumoto, Hideki; Aso, Tomokazu; Kato, Takashi; Ohtsu, Kiichi; Hasegawa, Shoichi; Maekawa, Fujio; Futakawa, Masatoshi

2009-02-01

As one of the main experimental facilities in J-PARC, an intense spallation neutron source (JSNS) driven by a 1-MW proton beam selected supercritical hydrogen at a temperature of 20 K and a pressure of 1.5 MPa as a moderator material. Moderators are controlled by a cryogenic hydrogen system that has a hydrogen relief system, which consists of high and low pressure stage of manifolds, a hydrogen vent line and a stack, in order to release hydrogen to the outside safely. The design of the hydrogen vent line should be considered to prevent purge nitrogen gas in the vent line from freezing when releasing the cryogenic hydrogen, to prevent moisture in the stack placed in an outdoor location from freezing, and to inhibit large piping temperature reduction at a building wall penetration. In this work, temperature change behaviors in the hydrogen vent line were analyzed by using a CFD code, STAR-CD. We determined required sizes of the vent line based on the analytical results and its layout in the building.

76 FR 28925 - Tribal Veterans Cemetery Grants

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-19

... means the process of site selection, land acquisition, design and planning, earth moving, landscaping... space, or functional layout; and it will not enter into a construction contract for the project or... State or Tribal Organization and the design team to provide a standard for preparation of drawings...

Chemical Mahjong

ERIC Educational Resources Information Center

Cossairt, Travis J.; Grubbs, W. Tandy

2011-01-01

An open-access, Web-based mnemonic game is described whereby introductory chemistry knowledge is tested using mahjong solitaire game play. Several tile sets and board layouts are included that are themed upon different chemical topics. Introductory tile sets can be selected that prompt the player to match element names to symbols and metric…

Automatic Constraint Detection for 2D Layout Regularization.

PubMed

Jiang, Haiyong; Nan, Liangliang; Yan, Dong-Ming; Dong, Weiming; Zhang, Xiaopeng; Wonka, Peter

2016-08-01

In this paper, we address the problem of constraint detection for layout regularization. The layout we consider is a set of two-dimensional elements where each element is represented by its bounding box. Layout regularization is important in digitizing plans or images, such as floor plans and facade images, and in the improvement of user-created contents, such as architectural drawings and slide layouts. To regularize a layout, we aim to improve the input by detecting and subsequently enforcing alignment, size, and distance constraints between layout elements. Similar to previous work, we formulate layout regularization as a quadratic programming problem. In addition, we propose a novel optimization algorithm that automatically detects constraints. We evaluate the proposed framework using a variety of input layouts from different applications. Our results demonstrate that our method has superior performance to the state of the art.

Re-Engineering the ISS Payload Operations Control Center During Increased Utilization and Critical Onboard Events

NASA Technical Reports Server (NTRS)

Dudley, Stephanie R. B.; Marsh, Angela L.

2014-01-01

With an increase in utilization and hours of payload operations being executed onboard the International Space Station (ISS), upgrading the NASA Marshall Space Flight Center (MSFC) Huntsville Operations Support Center (HOSC) ISS Payload Control Area (PCA) was essential to gaining efficiencies and assurance of current and future payload health and science return. PCA houses the Payload Operations Integration Center (POIC) responsible for the execution of all NASA payloads onboard the ISS. POIC Flight Controllers are responsible for the operation of voice, stowage, command, telemetry, video, power, thermal, and environmental control in support of ISS science experiments. The methodologies and execution of the PCA refurbishment were planned and performed within a four-month period in order to assure uninterrupted operation of ISS payloads and minimal impacts to payload operations teams. To vacate the PCA, three additional HOSC control rooms were reconfigured to handle ISS real-time operations, Backup Control Center (BCC) to Mission Control in Houston, simulations, and testing functions. This involved coordination and cooperation from teams of ISS operations controllers, multiple engineering and design disciplines, management, and construction companies performing an array of activities simultaneously and in sync delivering a final product with no issues that impacted the schedule. For each console operator discipline, studies of Information Technology (IT) tools and equipment layouts, ergonomics, and lines of sight were performed. Infusing some of the latest IT into the project was an essential goal in ensuring future growth and success of the ISS payload science returns. Engineering evaluations led to a state of the art Video Wall implementation and more efficient ethernet cabling distribution providing the latest products and the best solution for the POIC. These engineering innovations led to cost savings for the project. Constraints involved in the management of the project included executing over 450 crew-hours of ISS real-time payload operations including a major onboard communications upgrade, SpaceX un-berth, a Soyuz launch, roll-out of ISS live video and interviews from the POIC, annual BCC certification and hurricane season, and ISS simulations and testing. Continuous ISS payload operations were possible during the PCA facility modifications with the reconfiguration of four control rooms and standup of two temporary control areas. Another major restriction to the project was an ongoing facility upgrade that included a NASA Headquarters mandated replacement of all electrical and mechanical systems and replacement of an external generator. These upgrades required a facility power outage during the PCA upgrades. The project also encompassed console layout designs and ordering, amenities selections and ordering, excessing of old equipment, moves, disposal of old IT equipment, camera installations, facility tour re-schedules, and contract justifications. These were just some of the tasks needed for a successful project. This paper describes the logistics and lessons learned in upgrading a control center capability in the middle of complex real-time operations. Combining the efficiencies of controller interaction and new technology infusion were prime drivers for this upgrade to handle the increased utilization of science research on ISS. The success of this project could not jeopardize the current operations while these facility upgrades occurred.

CONCEPTUAL DESIGN ASSESSMENT FOR THE CO-FIRING OF BIO-REFINERY SUPPLIED LIGNIN PROJECT

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ted Berglund; Jeffrey T. Ranney; Carol L. Babb

2002-04-01

The major aspects of this project are proceeding toward completion. Prior to this quarter, design criteria, tentative site selection, facility layout, and preliminary facility cost estimates were completed and issued. Processing of bio-solids was completed, providing material for the pilot operations. Pilot facility hydrolysis production has been completed to produce lignin for co-fire testing and the lignin fuel was washed and dewatered. Both the lignin and bio-solids fuel materials for co-fire testing were sent to the co-fire facility (EERC) for evaluation and co-firing. EERC has received coal typical of the fuel to the TVA-Colbert boilers. This material was used atmore » EERC as baseline material and for mixing with the bio-fuel for combustion testing. All the combustion and fuel handling tests at EERC have been completed. During fuel preparation EERC reported no difficulties in fuel blending and handling. Preliminary co-fire test results indicate that the blending of lignin and bio-solids with the Colbert coal blend generally reduces NO{sub x} emissions, increases the reactivity of the coal, and increases the ash deposition rate on superheater surfaces. Deposits produced from the fuel blends, however, are more friable and hence easier to remove from tube surfaces relative to those produced from the baseline Colbert coal blend. The final co-fire testing report is being prepared at EERC and will be completed by the end of the second quarter of 2002. The TVA-Colbert facility has neared completion of the task to evaluate co-location of the Masada facility on the operation of the power generation facility. The TVA-Colbert fossil plant is fully capable of providing a reliable steam supply. The preferred steam supply connection points and steam pipeline routing have been identified. The environmental review of the pipeline routing has been completed and no major impacts have been identified. Detailed assessment of steam export impacts on the Colbert boiler system have been completed and a cost estimate for the steam supply system was completed. The cost estimate and output and heat rate impacts have been used to determine a preliminary price for the exported steam. TVA is further evaluating the impacts of adding lignin to the coal fuel blend and how the steam cost is impacted by proximity of the Masada biomass facility.« less

[The patient and family satisfaction with the department of mental health in Rome].

PubMed

Cozza, M; Amara, M; Butera, N; Infantino, G; Monti, A M; Provénzano, R

1997-01-01

Satisfaction's measurement with Mental Health Services in patients and their relatives. Satisfaction scale administration to the patients who were treated in community-based psychiatric service from 1.1.1996 to 31.3.1996 and the relatives who were primarily involved in caring for the patient. The ASL Rome "C" community-based psychiatric service. Verona Service Satisfaction Scale-54, a multidimensional instrument which measure satisfaction with community-based psychiatric service. Main results (301 scales for patients, 163 scales for relatives), pointed out for patients a higher satisfaction for the technical and interpersonal skills of psychiatrists and psychologists (score of specific items > 4). Lowest scores of satisfaction were towards the appearance, comfort level and physical layout of the facility (score 2.95) and towards the response of the service to emergencies during the night, weekend and Bank Holidays (score 2.87). Relatives were not particularly keen for the item regarding help to find open employment (score 2.76). Furthermore patients and their relatives gave a negative evaluation of the publicity and information offered by Mental Health Services. Dimension's analysis reaches the same conclusions deduced items's average score. The result of this study emphasizes the patients higher degree of satisfaction than the relatives. The above results point out three aspects to be improved by the Mental Health Service in order to satisfy the demands of the patients and relatives: 1. appearance, comfort level and physical layout of the facility, 2. publicity and information, 3. social activities and social skills.

HOLA: Human-like Orthogonal Network Layout.

PubMed

Kieffer, Steve; Dwyer, Tim; Marriott, Kim; Wybrow, Michael

2016-01-01

Over the last 50 years a wide variety of automatic network layout algorithms have been developed. Some are fast heuristic techniques suitable for networks with hundreds of thousands of nodes while others are multi-stage frameworks for higher-quality layout of smaller networks. However, despite decades of research currently no algorithm produces layout of comparable quality to that of a human. We give a new "human-centred" methodology for automatic network layout algorithm design that is intended to overcome this deficiency. User studies are first used to identify the aesthetic criteria algorithms should encode, then an algorithm is developed that is informed by these criteria and finally, a follow-up study evaluates the algorithm output. We have used this new methodology to develop an automatic orthogonal network layout method, HOLA, that achieves measurably better (by user study) layout than the best available orthogonal layout algorithm and which produces layouts of comparable quality to those produced by hand.

[VDT worker's posture and workload in free-address office system].

PubMed

Iwakiri, Kazuyuki; Mori, Ippei; Sotoyama, Midori; Nose, Kaori; Ochiai, Takanori; Jonai, Hiroshi; Saito, Susumu

2006-01-01

A free-address system is a new office layout in which a worker can freely sit in their favorite place with a computer and materials. Since this layout has recently been introduced in offices, we conducted a questionnaire survey which aimed to clarify the effects of the free-address system on visual display terminals (VDT) workers' posture and workload. A total of 203 male VDT workers who were system engineers aged 20 to 59 using a notebook computer were evaluated, of whom 150 used the free-address layout, and 53 used the fixed-address layout. The free-address layout was effective in the improvement of individual work space compared with the fixed-address layout. Also, in this layout the worker did not feel dissatisfaction with communication or support between workers. However, workers using the free-address layout assumed an unsuitable work posture, without adjusting the height of their chairs. Furthermore, this layout might have risk factors which increase neck/shoulder and low back stiffness and/or pain. Therefore, the free-address layout may have incipient problems, and it will be necessary to examine further the effects of this layout on VDT worker's health.

Selective Dry Etch for Defining Ohmic Contacts for High Performance ZnO TFTs

DTIC Science & Technology

2014-03-27

scale, high-frequency ZnO thin - film transistors (TFTs) could be fabricated. Molybdenum, tantalum, titanium tungsten 10-90, and tungsten metallic contact... thin - film transistor layout utilized in the thesis research . . . . . 42 3.4 Process Flow Diagram for Optical and e-Beam Devices...TFT thin - film transistor TLM transmission line model UV ultra-violet xvii SELECTIVE DRY ETCH FOR DEFINING OHMIC CONTACTS FOR HIGH PERFORMANCE ZnO TFTs

Environmental Development cum Forest Plantation Planning and Management.

ERIC Educational Resources Information Center

Katoch, C. D.

This textbook covers environmental conservation through forest plantation planning and management for all levels of forestry professionals and non-professionals in India and abroad. The book is divided into six parts and 29 sections in sequential order. Part I contains details on site selection, site preparations, site clearance, layout, and…

The Design of English Elementary and Primary Schools. A Select Annotated Bibliography.

ERIC Educational Resources Information Center

McNicholas, John, Comp.

School building design in this publication is interpreted as meaning layout and arrangement of rooms rather than as architectural style. Citations are organized under (1) central authority publications, (2) local authority publications, (3) general works, (4) articles in periodicals, and (5) unpublished theses. (Author/MLF)

Techniques for optimizing human-machine information transfer related to real-time interactive display systems

NASA Technical Reports Server (NTRS)

Granaas, Michael M.; Rhea, Donald C.

1989-01-01

The requirements for the development of real-time displays are reviewed. Of particular interest are the psychological aspects of design such as the layout, color selection, real-time response rate, and the interactivity of displays. Some existing Western Aeronautical Test Range displays are analyzed.

Basics of Desktop Publishing. Second Edition.

ERIC Educational Resources Information Center

Beeby, Ellen; Crummett, Jerrie

This document contains teacher and student materials for a basic course in desktop publishing. Six units of instruction cover the following: (1) introduction to desktop publishing; (2) desktop publishing systems; (3) software; (4) type selection; (5) document design; and (6) layout. The teacher edition contains some or all of the following…

An efficient way of layout processing based on calibre DRC and pattern matching for defects inspection application

NASA Astrophysics Data System (ADS)

Li, Helen; Lee, Robben; Lee, Tyzy; Xue, Teddy; Liu, Hermes; Wu, Hall; Wan, Qijian; Du, Chunshan; Hu, Xinyi; Liu, Zhengfang

2018-03-01

As technology advances, escalating layout design complexity and chip size make defect inspection becomes more challenging than ever before. The YE (Yield Enhancement) engineers are seeking for an efficient strategy to ensure accuracy without suffering running time. A smart way is to set different resolutions for different pattern structures, for examples, logic pattern areas have a higher scan resolution while the dummy areas have a lower resolution, SRAM area may have another different resolution. This can significantly reduce the scan processing time meanwhile the accuracy does not suffer. Due to the limitation of the inspection equipment, the layout must be processed in order to output the Care Area marker in line with the requirement of the equipment, for instance, the marker shapes must be rectangle and the number of the rectangle shapes should be as small as possible. The challenge is how to select the different Care Areas by pattern structures, merge the areas efficiently and then partition them into pieces of rectangle shapes. This paper presents a solution based on Calibre DRC and Pattern Matching. Calibre equation-based DRC is a powerful layout processing engine and Calibre Pattern Matching's automated visual capture capability enables designers to define these geometries as layout patterns and store them in libraries which can be re-used in multiple design layouts. Pattern Matching simplifies the description of very complex relationships between pattern shapes efficiently and accurately. Pattern matching's true power is on display when it is integrated with normal DRC deck. In this application of defects inspection, we first run Calibre DRC to get rule based Care Area then use Calibre Pattern Matching's automated pattern capture capability to capture Care Area shapes which need a higher scan resolution with a tune able pattern halo. In the pattern matching step, when the patterns are matched, a bounding box marker will be output to identify the high resolution area. The equation-based DRC and Pattern Matching effectively work together for different scan phases.

32 CFR 553.7 - Design and layout of Army national cemeteries.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 32 National Defense 3 2012-07-01 2009-07-01 true Design and layout of Army national cemeteries... RESERVATIONS AND NATIONAL CEMETERIES ARMY NATIONAL CEMETERIES § 553.7 Design and layout of Army national cemeteries. (a) General cemetery layout plans, landscape planting plans and gravesite layout plans for Army...

32 CFR 553.7 - Design and layout of Army national cemeteries.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 32 National Defense 3 2011-07-01 2009-07-01 true Design and layout of Army national cemeteries... RESERVATIONS AND NATIONAL CEMETERIES ARMY NATIONAL CEMETERIES § 553.7 Design and layout of Army national cemeteries. (a) General cemetery layout plans, landscape planting plans and gravesite layout plans for Army...

32 CFR 553.7 - Design and layout of Army national cemeteries.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 32 National Defense 3 2014-07-01 2014-07-01 false Design and layout of Army national cemeteries... RESERVATIONS AND NATIONAL CEMETERIES ARMY NATIONAL CEMETERIES § 553.7 Design and layout of Army national cemeteries. (a) General cemetery layout plans, landscape planting plans and gravesite layout plans for Army...

32 CFR 553.7 - Design and layout of Army national cemeteries.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 32 National Defense 3 2010-07-01 2010-07-01 true Design and layout of Army national cemeteries... RESERVATIONS AND NATIONAL CEMETERIES ARMY NATIONAL CEMETERIES § 553.7 Design and layout of Army national cemeteries. (a) General cemetery layout plans, landscape planting plans and gravesite layout plans for Army...

32 CFR 553.7 - Design and layout of Army national cemeteries.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 32 National Defense 3 2013-07-01 2013-07-01 false Design and layout of Army national cemeteries... RESERVATIONS AND NATIONAL CEMETERIES ARMY NATIONAL CEMETERIES § 553.7 Design and layout of Army national cemeteries. (a) General cemetery layout plans, landscape planting plans and gravesite layout plans for Army...

48 CFR 52.236-17 - Layout of Work.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 48 Federal Acquisition Regulations System 2 2011-10-01 2011-10-01 false Layout of Work. 52.236-17... Layout of Work. As prescribed in 36.517, insert the following clause in solicitations and contracts when... need for accurate work layout and for siting verification during work performance: Layout of Work (APR...

48 CFR 52.236-17 - Layout of Work.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 48 Federal Acquisition Regulations System 2 2010-10-01 2010-10-01 false Layout of Work. 52.236-17... Layout of Work. As prescribed in 36.517, insert the following clause in solicitations and contracts when... need for accurate work layout and for siting verification during work performance: Layout of Work (APR...

KSC-04PD-1563

NASA Technical Reports Server (NTRS)

2004-01-01

KENNEDY SPACE CENTER, FLA. Sen. Bill Nelson (right), D-Fla., explains the layout of the glass cockpit to Sen. John F. Kerry, D-Mass., on the flight deck of orbiter Discovery during a tour of the Orbiter Processing Facility (OPF). The bunny suits they are wearing are clean room attire required for anyone coming in close proximity to Discovery, currently being prepared for flight on the next Space Shuttle mission. The tour of the OPF follows a public meeting Kerry held at the Dr. Kurt H. Debus Conference Facility at the Kennedy Space Center Visitor Complex. He said he chose to speak at KSC because it symbolizes Americas commitment to science, innovation and technology. He and Sen. John Edwards, D-N.C., are on a speaking tour prior to their appearance at the Democratic National Convention in Boston.

Optimization of RET flow using test layout

NASA Astrophysics Data System (ADS)

Zhang, Yunqiang; Sethi, Satyendra; Lucas, Kevin

2008-11-01

At advanced technology nodes with extremely low k1 lithography, it is very hard to achieve image fidelity requirements and process window for some layout configurations. Quite often these layouts are within simple design rule constraints for a given technology node. It is important to have these layouts included during early RET flow development. Most of RET developments are based on shrunk layout from the previous technology node, which is possibly not good enough. A better methodology in creating test layout is required for optical proximity correction (OPC) recipe and assists feature development. In this paper we demonstrate the application of programmable test layouts in RET development. Layout pattern libraries are developed and embedded in a layout tool (ICWB). Assessment gauges are generated together with patterns for quick correction accuracy assessment. Several groups of test pattern libraries have been developed based on learning from product patterns and a layout DOE approach. The interaction between layout patterns and OPC recipe has been studied. Correction of a contact layer is quite challenge because of poor convergence and low process window. We developed test pattern library with many different contact configurations. Different OPC schemes are studied on these test layouts. The worst process window patterns are pinpointed for a given illumination condition. Assist features (AF) are frequently placed according to pre-determined rules to improve lithography process window. These rules are usually derived from lithographic models and experiments. Direct validation of AF rules is required at development phase. We use the test layout approach to determine rules in order to eliminate AF printability problem.

UCx target preparations and characterizations

NASA Astrophysics Data System (ADS)

Andrighetto, Alberto; Corradetti, Stefano; Manzolaro, Mattia; Scarpa, Daniele; Monetti, Alberto; Rossignoli, Massimo; Borgna, Francesca; Ballan, Michele; Agostini, Mattia; D'Agostini, Fabio; Ferrari, Matteo; Zenoni, Aldo

2018-05-01

The Target-Ion Source unit is the core of an ISOL-RIB facility. Many international ISOL facilities have chosen different layouts of this unit. Many research groups are involved in research and development of targets capable of dissipating high power and, at the same time, be able to have a fast isotope release. This is mandatory in order to produce beams of short half-life isotopes. The research of new materials with advanced microstructural features is crucial in this field. The design of a proper target is indeed strictly related to the obtainment of porous refractory materials, which are capable to work under extreme conditions (temperatures up to 2000 °C in high vacuum) with a high release efficiency. For SPES, the second generation Italian ISOL-RIB Facility, the target will be made of uranium carbide (UCx) in which, by fission induced by a proton beam of 40 MeV of energy (8 kW of power), isotopes in the 60-160 amu mass region are produced. The current technological developments are also crucial in the study of third generation ISOL facilities.

Multi-modality molecular imaging: pre-clinical laboratory configuration

NASA Astrophysics Data System (ADS)

Wu, Yanjun; Wellen, Jeremy W.; Sarkar, Susanta K.

2006-02-01

In recent years, the prevalence of in vivo molecular imaging applications has rapidly increased. Here we report on the construction of a multi-modality imaging facility in a pharmaceutical setting that is expected to further advance existing capabilities for in vivo imaging of drug distribution and the interaction with their target. The imaging instrumentation in our facility includes a microPET scanner, a four wavelength time-domain optical imaging scanner, a 9.4T/30cm MRI scanner and a SPECT/X-ray CT scanner. An electronics shop and a computer room dedicated to image analysis are additional features of the facility. The layout of the facility was designed with a central animal preparation room surrounded by separate laboratory rooms for each of the major imaging modalities to accommodate the work-flow of simultaneous in vivo imaging experiments. This report will focus on the design of and anticipated applications for our microPET and optical imaging laboratory spaces. Additionally, we will discuss efforts to maximize the daily throughput of animal scans through development of efficient experimental work-flows and the use of multiple animals in a single scanning session.

Flow analysis of airborne particles in a hospital operating room

NASA Astrophysics Data System (ADS)

Faeghi, Shiva; Lennerts, Kunibert

2016-06-01

Preventing airborne infections during a surgery has been always an important issue to deliver effective and high quality medical care to the patient. One of the important sources of infection is particles that are distributed through airborne routes. Factors influencing infection rates caused by airborne particles, among others, are efficient ventilation and the arrangement of surgical facilities inside the operating room. The paper studies the ventilation airflow pattern in an operating room in a hospital located in Tehran, Iran, and seeks to find the efficient configurations with respect to the ventilation system and layout of facilities. This study uses computational fluid dynamics (CFD) and investigates the effects of different inflow velocities for inlets, two pressurization scenarios (equal and excess pressure) and two arrangements of surgical facilities in room while the door is completely open. The results show that system does not perform adequately when the door is open in the operating room under the current conditions, and excess pressure adjustments should be employed to achieve efficient results. The findings of this research can be discussed in the context of design and controlling of the ventilation facilities of operating rooms.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rutherford, Victor Stephen

Los Alamos National Laboratory (LANL) will conduct familiarization tours for personnel of the Los Alamos County Fire Department (LAFD) at TA-16 high explosives (HE) facilities. These familiarization tours are official LANL business; the purpose of these tours is to orient LAFD firefighters to the facility so that they can respond efficiently and quickly to a variety of emergency situations. This orientation includes, among other topics, ingress and egress of the area and buildings, layout and organization of the facility, evacuation procedures and assembly points, and areas of concern within the various buildings at the facility. LAFD firefighters have the skillsmore » and abilities to perform firefighting operations and other emergency response tasks that cannot be provided by LANL personnel who have the required clearance. This handout provides details of the information, along with maps and diagrams, to be presented during the familiarization tours. The handout will be distributed to the trainees at the time of the tour. A corresponding checklist will also be used as guidance during the familiarization tours to ensure that all required information is presented to LAFD personnel.« less

The Super Separator Spectrometer S3 and the associated detection systems: SIRIUS & LEB-REGLIS3

NASA Astrophysics Data System (ADS)

Déchery, F.; Savajols, H.; Authier, M.; Drouart, A.; Nolen, J.; Ackermann, D.; Amthor, A. M.; Bastin, B.; Berryhill, A.; Boutin, D.; Caceres, L.; Coffey, M.; Delferrière, O.; Dorvaux, O.; Gall, B.; Hauschild, K.; Hue, A.; Jacquot, B.; Karkour, N.; Laune, B.; Le Blanc, F.; Lecesne, N.; Lopez-Martens, A.; Lutton, F.; Manikonda, S.; Meinke, R.; Olivier, G.; Payet, J.; Piot, J.; Pochon, O.; Prince, V.; Souli, M.; Stelzer, G.; Stodel, C.; Stodel, M.-H.; Sulignano, B.; Traykov, E.; Uriot, D.; S³, Sirius; Leb-Reglis3 Collaboration

2016-06-01

The Super Separator Spectrometer (S3) facility is developed in the framework of the SPIRAL2 project [1]. S3 has been designed to extend the capability of the facility to perform experiments with extremely low cross sections, taking advantage of the very high intensity stable beams of the superconducting linear accelerator of SPIRAL2. It will mainly use fusion-evaporation reactions to reach extreme regions of the nuclear chart: new opportunities will be opened for super-heavy element studies and spectroscopy at and beyond the driplines. In addition to our previous article (Déchery et al. [2]) introducing the optical layout of the spectrometer and the expected performances, this article will present the current status of the main elements of the facility: the target station, the superconducting multipole, and the magnetic and electric dipoles, with a special emphasis on the status of the detection system SIRIUS and on the low-energy branch which includes the REGLIS3 system. S3 will also be a source of low energy radioactive isotopes for delivery to the DESIR facility.

Los Alamos County Fire Department LAFD: TA-55 PF-4 Facility Familiarization Tour, OJT 55260

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rutherford, Victor Stephen

Los Alamos National Laboratory (LANL) will conduct familiarization tours for Los Alamos County Fire Department (LAFD) personnel at the Plutonium Facility (PF-4) at Technical Area (TA)-55. These familiarization tours are official LANL business; the purpose of these tours is to orient the firefighters to the facility so that they can respond efficiently and quickly to a variety of emergency situations. This orientation includes the ingress and egress of the area and buildings, layout and organization of the facility, evacuation procedures and assembly points, and areas of concern within the various buildings at the facility. LAFD firefighters have the skills andmore » abilities to perform firefighting operations and other emergency response tasks that cannot be provided by other LANL personnel who have the required clearance level. This handout provides details of the information, along with maps and diagrams, to be presented during the familiarization tours. The handout will be distributed to the trainees at the time of the tour. A corresponding checklist will also be used as guidance during the familiarization tours to ensure that all required information is presented to LAFD personnel.« less

LAFD: TA-55 RLUOB/CUB Facility Familiarization Tour, OJT #55265

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rutherford, Victor Stephen

2017-09-14

Los Alamos National Laboratory (LANL) conducts familiarization tours for personnel of the Los Alamos County Fire Department (LAFD) at the RLUOB/CUB, technical area (TA)-55, 400/440, facility, Radiological Laboratory Utility Office Building (RLUOB)/Central Utility Building (CUB). These familiarization tours are official LANL business; the purpose of these tours is to orient LAFD firefighters to the facility so that they can respond efficiently and quickly to a variety of emergency situations. This orientation includes, among other topics, the ingress and egress of the area and buildings, layout and organization of the facility, evacuation procedures and assembly points, and areas of concern withinmore » the various buildings at the facility. LAFD firefighters have the skills and abilities to perform firefighting operations and other emergency response tasks that cannot be provided by other LANL personnel who have the required clearance level. This handout provides details of the information, along with maps and diagrams, to be presented during the familiarization tours. The handout is distributed to the trainees at the time of the tour; a corresponding checklist is also used as guidance during the familiarization tours to ensure that all required information is presented to LAFD personnel.« less

An efficient grid layout algorithm for biological networks utilizing various biological attributes

PubMed Central

Kojima, Kaname; Nagasaki, Masao; Jeong, Euna; Kato, Mitsuru; Miyano, Satoru

2007-01-01

Background Clearly visualized biopathways provide a great help in understanding biological systems. However, manual drawing of large-scale biopathways is time consuming. We proposed a grid layout algorithm that can handle gene-regulatory networks and signal transduction pathways by considering edge-edge crossing, node-edge crossing, distance measure between nodes, and subcellular localization information from Gene Ontology. Consequently, the layout algorithm succeeded in drastically reducing these crossings in the apoptosis model. However, for larger-scale networks, we encountered three problems: (i) the initial layout is often very far from any local optimum because nodes are initially placed at random, (ii) from a biological viewpoint, human layouts still exceed automatic layouts in understanding because except subcellular localization, it does not fully utilize biological information of pathways, and (iii) it employs a local search strategy in which the neighborhood is obtained by moving one node at each step, and automatic layouts suggest that simultaneous movements of multiple nodes are necessary for better layouts, while such extension may face worsening the time complexity. Results We propose a new grid layout algorithm. To address problem (i), we devised a new force-directed algorithm whose output is suitable as the initial layout. For (ii), we considered that an appropriate alignment of nodes having the same biological attribute is one of the most important factors of the comprehension, and we defined a new score function that gives an advantage to such configurations. For solving problem (iii), we developed a search strategy that considers swapping nodes as well as moving a node, while keeping the order of the time complexity. Though a naïve implementation increases by one order, the time complexity, we solved this difficulty by devising a method that caches differences between scores of a layout and its possible updates. Conclusion Layouts of the new grid layout algorithm are compared with that of the previous algorithm and human layout in an endothelial cell model, three times as large as the apoptosis model. The total cost of the result from the new grid layout algorithm is similar to that of the human layout. In addition, its convergence time is drastically reduced (40% reduction). PMID:17338825

Layout Design of Human-Machine Interaction Interface of Cabin Based on Cognitive Ergonomics and GA-ACA.

PubMed

Deng, Li; Wang, Guohua; Yu, Suihuai

2016-01-01

In order to consider the psychological cognitive characteristics affecting operating comfort and realize the automatic layout design, cognitive ergonomics and GA-ACA (genetic algorithm and ant colony algorithm) were introduced into the layout design of human-machine interaction interface. First, from the perspective of cognitive psychology, according to the information processing process, the cognitive model of human-machine interaction interface was established. Then, the human cognitive characteristics were analyzed, and the layout principles of human-machine interaction interface were summarized as the constraints in layout design. Again, the expression form of fitness function, pheromone, and heuristic information for the layout optimization of cabin was studied. The layout design model of human-machine interaction interface was established based on GA-ACA. At last, a layout design system was developed based on this model. For validation, the human-machine interaction interface layout design of drilling rig control room was taken as an example, and the optimization result showed the feasibility and effectiveness of the proposed method.

Layout Design of Human-Machine Interaction Interface of Cabin Based on Cognitive Ergonomics and GA-ACA

PubMed Central

Deng, Li; Wang, Guohua; Yu, Suihuai

2016-01-01

In order to consider the psychological cognitive characteristics affecting operating comfort and realize the automatic layout design, cognitive ergonomics and GA-ACA (genetic algorithm and ant colony algorithm) were introduced into the layout design of human-machine interaction interface. First, from the perspective of cognitive psychology, according to the information processing process, the cognitive model of human-machine interaction interface was established. Then, the human cognitive characteristics were analyzed, and the layout principles of human-machine interaction interface were summarized as the constraints in layout design. Again, the expression form of fitness function, pheromone, and heuristic information for the layout optimization of cabin was studied. The layout design model of human-machine interaction interface was established based on GA-ACA. At last, a layout design system was developed based on this model. For validation, the human-machine interaction interface layout design of drilling rig control room was taken as an example, and the optimization result showed the feasibility and effectiveness of the proposed method. PMID:26884745

The checkpoint ordering problem

PubMed Central

Hungerländer, P.

2017-01-01

Abstract We suggest a new variant of a row layout problem: Find an ordering of n departments with given lengths such that the total weighted sum of their distances to a given checkpoint is minimized. The Checkpoint Ordering Problem (COP) is both of theoretical and practical interest. It has several applications and is conceptually related to some well-studied combinatorial optimization problems, namely the Single-Row Facility Layout Problem, the Linear Ordering Problem and a variant of parallel machine scheduling. In this paper we study the complexity of the (COP) and its special cases. The general version of the (COP) with an arbitrary but fixed number of checkpoints is NP-hard in the weak sense. We propose both a dynamic programming algorithm and an integer linear programming approach for the (COP) . Our computational experiments indicate that the (COP) is hard to solve in practice. While the run time of the dynamic programming algorithm strongly depends on the length of the departments, the integer linear programming approach is able to solve instances with up to 25 departments to optimality. PMID:29170574

The LArIAT experiment: first measurement of the inclusive total pion cross-section in Argon

NASA Astrophysics Data System (ADS)

de María Blaszczyk, Flor

2018-05-01

In light of future large neutrino experiments such as DUNE, an excellent understanding of LArTPCs is required. The Liquid Argon In A Test-beam (LArIAT) experiment, located in the Fermilab Test Beam Facility, is designed to characterize the performance of LArTPCs and improve the reconstruction algorithms but also to measure the cross-sections of charged particles in Argon. The goals and experimental layout will be presented, as well as the world’s first inclusive total pion interaction cross-section on Argon measured by LArIAT.

A Simple and Resource-efficient Setup for the Computer-aided Drug Design Laboratory.

PubMed

Moretti, Loris; Sartori, Luca

2016-10-01

Undertaking modelling investigations for Computer-Aided Drug Design (CADD) requires a proper environment. In principle, this could be done on a single computer, but the reality of a drug discovery program requires robustness and high-throughput computing (HTC) to efficiently support the research. Therefore, a more capable alternative is needed but its implementation has no widespread solution. Here, the realization of such a computing facility is discussed, from general layout to technical details all aspects are covered. © 2016 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

9. Credit JPL. Photographic copy of drawing, engineering drawing showing ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

9. Credit JPL. Photographic copy of drawing, engineering drawing showing structure of Test Stand 'A' (Building 4202/E-3) and its relationship to the Monitor Building or blockhouse (Building 4203/E-4) when a reinforced concrete machinery room was added to the west side of Test Stand 'A' in 1955. California Institute of Technology, Jet Propulsion Laboratory, Plant Engineering 'Electrical Layout - Muroc, Test Stand & Refrigeration Equipment Room,' drawing no. E3/7-0, April 6, 1955. - Jet Propulsion Laboratory Edwards Facility, Test Stand A, Edwards Air Force Base, Boron, Kern County, CA

Uranium Enrichment Safeguards

DOE Office of Scientific and Technical Information (OSTI.GOV)

Demuth, Scott F.; Trahan, Alexis Chanel

2017-06-26

DIV of facility layout, material flows, and other information provided in the DIQ. Material accountancy through an annual PIV and a number of interim inventory verifications, including UF6 cylinder identification and counting, NDA of cylinders, and DA on a sample collection of UF6. Application of C/S technologies utilizing seals and tamper-indicating devices (TIDs) on cylinders, containers, storage rooms, and IAEA instrumentation to provide continuity of knowledge between inspection. Verification of the absence of undeclared material and operations, especially HEU production, through SNRIs, LFUA of cascade halls, and environmental swipe sampling

KSC-2013-1529

NASA Image and Video Library

2013-02-15

CAPE CANAVERAL, Fla. – An artist's concept shows a possible layout of a commercial spacecraft and rocket using facilities inside the Vehicle Assembly Building at NASA's Kennedy Space Center in Florida as the center undergoes a transformation into a multi-user spaceport. At left is the Space Launch System, or SLS, currently under development by NASA. At right is a generic rocket and spacecraft design indicative of the likely arrangement of such a vehicle. Several companies are designing rockets and spacecraft that could be used to launch astronauts and payloads into space in the future. Credit: NASA

Human factors in spacecraft design

NASA Technical Reports Server (NTRS)

Harrison, Albert A.; Connors, Mary M.

1990-01-01

This paper describes some of the salient implications of evolving mission parameters for spacecraft design. Among the requirements for future spacecraft are new, higher standards of living, increased support of human productivity, and greater accommodation of physical and cultural variability. Design issues include volumetric allowances, architecture and layouts, closed life support systems, health maintenance systems, recreational facilities, automation, privacy, and decor. An understanding of behavioral responses to design elements is a precondition for critical design decisions. Human factors research results must be taken into account early in the course of the design process.

Chemical Remote Sensing ’Proof of Concept’,

DTIC Science & Technology

1981-03-31

A122 579 CHEMICAL REMOTE SENSING ;PROOF OF CONCEPT’(U) UTAH 1/I \\ STATE UNIV LOGAN ELECTRO-DYNAMICS LAB BARTSCHI ET AL. 31 MAR 81 SCIENTIFC-8...STANDARDS -I963-A AFGL-TR-81-021 2 CHEMICAL REMOTE SENSING "Proof of Concept" B.Y. Bartschi F. P. DelGreco M. Ahmadjian Electro-Dynamics Laboratories...Applications of remote sensing 2 2.2 Program Development 4 -O 3.1 Optical Layout 6 3.2 Block Diagram of Sensor System 7 3.3 Sensor Facility 10 3.4

New library building: Mercer University School of Medicine, Macon, Georgia.

PubMed Central

Rankin, J A; Bernard, G R

1984-01-01

The Mercer University School of Medicine (MUSM) enrolled its charter class in 1982. The curriculum is problem-based and adaptable to the learning needs of each student. MUSM is housed in a new building designed to support this unique educational program. Its library is an example of a comparatively small, but fully functional, medical school library. The planning process, design, and layout of the new library facility are described. Among its unique features are an integrated print and non-print collection, current periodical display space, and extensive use of task lighting. PMID:6733330

Product Operations Status Summary Metrics

NASA Technical Reports Server (NTRS)

Takagi, Atsuya; Toole, Nicholas

2010-01-01

The Product Operations Status Summary Metrics (POSSUM) computer program provides a readable view into the state of the Phoenix Operations Product Generation Subsystem (OPGS) data pipeline. POSSUM provides a user interface that can search the data store, collect product metadata, and display the results in an easily-readable layout. It was designed with flexibility in mind for support in future missions. Flexibility over various data store hierarchies is provided through the disk-searching facilities of Marsviewer. This is a proven program that has been in operational use since the first day of the Phoenix mission.

Design and development of pressure and repressurization purge system for reusable space shuttle multilayer insulation system

NASA Technical Reports Server (NTRS)

1971-01-01

Preliminary design and analysis of purge system concepts and purge subsystem approaches are defined and evaluated. Acceptable purge subsystem approaches were combined into four predesign layouts which are presented for comparison and evaluation. Two predesigns were selected for further detailed design and evaluation for eventual selection of the best design for a full scale test configuration. An operation plan is included as an appendix for reference to shuttle-oriented operational parameters.

Expert system for generating initial layouts of zoom systems with multiple moving lens groups

NASA Astrophysics Data System (ADS)

Cheng, Xuemin; Wang, Yongtian; Hao, Qun; Sasián, José M.

2005-01-01

An expert system is developed for the automatic generation of initial layouts for the design of zoom systems with multiple moving lens groups. The Gaussian parameters of the zoom system are optimized using the damped-least-squares method to achieve smooth zoom cam curves, with the f-number of each lens group in the zoom system constrained to a rational value. Then each lens group is selected automatically from a database according to its range of f-number, field of view, and magnification ratio as it is used in the zoom system. The lens group database is established from the results of analyzing thousands of zoom lens patents. Design examples are given, which show that the scheme is a practical approach to generate starting points for zoom lens design.

Universality in the Evolution of Orientation Columns in the Visual Cortex

PubMed Central

Kaschube, Matthias; Schnabel, Michael; Löwel, Siegrid; Coppola, David M.; White, Leonard E.; Wolf, Fred

2011-01-01

The brain’s visual cortex processes information concerning form, pattern, and motion within functional maps that reflect the layout of neuronal circuits. We analyzed functional maps of orientation preference in the ferret, tree shrew, and galago—three species separated since the basal radiation of placental mammals more than 65 million years ago—and found a common organizing principle. A symmetry-based class of models for the self-organization of cortical networks predicts all essential features of the layout of these neuronal circuits, but only if suppressive long-range interactions dominate development. We show mathematically that orientation-selective long-range connectivity can mediate the required interactions. Our results suggest that self-organization has canalized the evolution of the neuronal circuitry underlying orientation preference maps into a single common design. PMID:21051599

Method and apparatus for displaying information

NASA Technical Reports Server (NTRS)

Huang, Sui (Inventor); Eichler, Gabriel (Inventor); Ingber, Donald E. (Inventor)

2010-01-01

A method for displaying large amounts of information. The method includes the steps of forming a spatial layout of tiles each corresponding to a representative reference element; mapping observed elements onto the spatial layout of tiles of representative reference elements; assigning a respective value to each respective tile of the spatial layout of the representative elements; and displaying an image of the spatial layout of tiles of representative elements. Each tile includes atomic attributes of representative elements. The invention also relates to an apparatus for displaying large amounts of information. The apparatus includes a tiler forming a spatial layout of tiles, each corresponding to a representative reference element; a comparator mapping observed elements onto said spatial layout of tiles of representative reference elements; an assigner assigning a respective value to each respective tile of said spatial layout of representative reference elements; and a display displaying an image of the spatial layout of tiles of representative reference elements.

Automated space processing payloads study. Volume 2, book 1: Technical report. [instrument packages and space shuttles

NASA Technical Reports Server (NTRS)

1975-01-01

The extent was investigated to which experiment hardware and operational requirements can be met by automatic control and material handling devices; payload and system concepts that make extensive use of automation technology are defined. Hardware requirements for each experiment were established and tabulated, and investigations of applicable existing hardware were documented. The capabilities and characteristics of industrial automation equipment, controls, and techniques are presented in the form of a summary of applicable equipment characteristics in three basic mutually-supporting formats. Facilities for performing groups of experiments are defined along with four levitation groups and three furnace groups; major hardware elements required to implement them were identified. A conceptual design definition of ten different automated processing facilities is presented along with the specific equipment to implement each facility and the design layouts of the different units. Constraints and packaging, weight, and power requirements for six payloads postulated for shuttle missions in the 1979 to 1982 time period were examined.

The development of an inherent safety approach to the prevention of domino accidents.

PubMed

Cozzani, Valerio; Tugnoli, Alessandro; Salzano, Ernesto

2009-11-01

The severity of industrial accidents in which a domino effect takes place is well known in the chemical and process industry. The application of an inherent safety approach for the prevention of escalation events leading to domino accidents was explored in the present study. Reference primary scenarios were analyzed and escalation vectors were defined. Inherent safety distances were defined and proposed as a metric to express the intensity of the escalation vectors. Simple rules of thumb were presented for a preliminary screening of these distances. Swift reference indices for layout screening with respect to escalation hazard were also defined. Two case studies derived from existing layouts of oil refineries were selected to understand the potentialities coming from the application in the methodology. The results evidenced that the approach allows a first comparative assessment of the actual domino hazard in a layout, and the identification of critical primary units with respect to escalation events. The methodology developed also represents a useful screening tool to identify were to dedicate major efforts in the design of add-on measures, optimizing conventional passive and active measures for the prevention of severe domino accidents.

Using pattern based layout comparison for a quick analysis of design changes

NASA Astrophysics Data System (ADS)

Huang, Lucas; Yang, Legender; Kan, Huan; Zou, Elain; Wan, Qijian; Du, Chunshan; Hu, Xinyi; Liu, Zhengfang

2018-03-01

A design usually goes through several versions until achieving a most successful one. These changes between versions are not a complete substitution but a continual improvement, either fixing the known issues of its prior versions (engineering change order) or a more optimized design substitution of a portion of the design. On the manufacturing side, process engineers care more about the design pattern changes because any new pattern occurrence may be a killer of the yield. An effective and efficient way to narrow down the diagnosis scope appeals to the engineers. What is the best approach of comparing two layouts? A direct overlay of two layouts may not always work as even though most of the design instances will be kept in the layout from version to version, the actual placements may be different. An alternative way, pattern based layout comparison, comes to play. By expanding this application, it makes it possible to transfer the learning in one cycle to another and accelerate the process of failure analysis. This paper presents a solution to compare two layouts by using Calibre DRC and Pattern Matching. The key step in this flow is layout decomposition. In theory, with a fixed pattern size, a layout can always be decomposed into limited number of patterns by moving the pattern center around the layout, the number is limited but may be huge if the layout is not processed smartly! A mathematical answer is not what we are looking for but an engineering solution is more desired. Layouts must be decomposed into patterns with physical meaning in a smart way. When a layout is decomposed and patterns are classified, a pattern library with unique patterns inside is created for that layout. After individual pattern libraries for each layout are created, run pattern comparison utility provided by Calibre Pattern Matching to compare the pattern libraries, unique patterns will come out for each layout. This paper illustrates this flow in details and demonstrates the advantage of combining Calibre DRC and Calibre Pattern Matching.

77 FR 67862 - Notice of Availability of the Final Environmental Assessment (EA) and Finding of No Significant...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-11-14

... the Aberdeen Regional Airport for current and projected levels of aviation by the design aircraft... wildlife habitat. The selected alternative includes the: (I.) Unconditional approval of the Airport Layout... eligible items. (4.) Approval of design and use of air traffic procedures needed to implement the proposed...

Use of Geometry for Spatial Reorientation in Children Applies Only to Symmetric Spaces

ERIC Educational Resources Information Center

Lew, Adina R.; Gibbons, Bryony; Murphy, Caroline; Bremner, J. Gavin

2010-01-01

Proponents of the geometric module hypothesis argue that following disorientation, many species reorient by use of macro-environment geometry. It is suggested that attention to the surface layout geometry of natural terrain features may have been selected for over evolutionary time due to the enduring and unambiguous location information it…

GABE: A Cloud Brokerage System for Service Selection, Accountability and Enforcement

ERIC Educational Resources Information Center

Sundareswaran, Smitha

2014-01-01

Much like its meteorological counterpart, "Cloud Computing" is an amorphous agglomeration of entities. It is amorphous in that the exact layout of the servers, the load balancers and their functions are neither known nor fixed. Its an agglomerate in that multiple service providers and vendors often coordinate to form a multitenant system…

Optimization lighting layout based on gene density improved genetic algorithm for indoor visible light communications

NASA Astrophysics Data System (ADS)

Liu, Huanlin; Wang, Xin; Chen, Yong; Kong, Deqian; Xia, Peijie

2017-05-01

For indoor visible light communication system, the layout of LED lamps affects the uniformity of the received power on communication plane. In order to find an optimized lighting layout that meets both the lighting needs and communication needs, a gene density genetic algorithm (GDGA) is proposed. In GDGA, a gene indicates a pair of abscissa and ordinate of a LED, and an individual represents a LED layout in the room. The segmented crossover operation and gene mutation strategy based on gene density are put forward to make the received power on communication plane more uniform and increase the population's diversity. A weighted differences function between individuals is designed as the fitness function of GDGA for reserving the population having the useful LED layout genetic information and ensuring the global convergence of GDGA. Comparing square layout and circular layout, with the optimized layout achieved by the GDGA, the power uniformity increases by 83.3%, 83.1% and 55.4%, respectively. Furthermore, the convergence of GDGA is verified compared with evolutionary algorithm (EA). Experimental results show that GDGA can quickly find an approximation of optimal layout.

A novel approach of ensuring layout regularity correct by construction in advanced technologies

NASA Astrophysics Data System (ADS)

Ahmed, Shafquat Jahan; Vaderiya, Yagnesh; Gupta, Radhika; Parthasarathy, Chittoor; Marin, Jean-Claude; Robert, Frederic

2017-03-01

In advanced technology nodes, layout regularity has become a mandatory prerequisite to create robust designs less sensitive to variations in manufacturing process in order to improve yield and minimizing electrical variability. In this paper we describe a method for designing regular full custom layouts based on design and process co-optimization. The method includes various design rule checks that can be used on-the-fly during leaf-cell layout development. We extract a Layout Regularity Index (LRI) from the layouts based on the jogs, alignments and pitches used in the design for any given metal layer. Regularity Index of a layout is the direct indicator of manufacturing yield and is used to compare the relative health of different layout blocks in terms of process friendliness. The method has been deployed for 28nm and 40nm technology nodes for Memory IP and is being extended to other IPs (IO, standard-cell). We have quantified the gain of layout regularity with the deployed method on printability and electrical characteristics by process-variation (PV) band simulation analysis and have achieved up-to 5nm reduction in PV band.

Comparison of a traditional and non-traditional residential care facility for persons living with dementia and the impact of the environment on occupational engagement.

PubMed

Richards, Kieva; D'Cruz, Rachel; Harman, Suzanne; Stagnitti, Karen

2015-12-01

Dementia residential facilities can be described as traditional or non-traditional facilities. Non-traditional facilities aim to utilise principles of environmental design to create a milieu that supports persons experiencing cognitive decline. This study aimed to compare these two environments in rural Australia, and their influence on residents' occupational engagement. The Residential Environment Impact Survey (REIS) was used and consists of: a walk-through of the facility; activity observation; interviews with residents and employees. Thirteen residents were observed and four employees interviewed. Resident interviews did not occur given the population diagnosis of moderate to severe dementia. Descriptive data from the walk-through and activity observation were analysed for potential opportunities of occupational engagement. Interviews were thematically analysed to discern perception of occupational engagement of residents within their facility. Both facilities provided opportunities for occupational engagement. However, the non-traditional facility provided additional opportunities through employee interactions and features of the physical environment. Interviews revealed six themes: Comfortable environment; roles and responsibilities; getting to know the resident; more stimulation can elicit increased engagement; the home-like experience and environmental layout. These themes coupled with the features of the environment provided insight into the complexity of occupational engagement within this population. This study emphasises the influence of the physical and social environment on occupational engagement opportunities. A non-traditional dementia facility maximises these opportunities and can support development of best-practice guidelines within this population. © 2015 Occupational Therapy Australia.

Interior design of the lunar outpost

NASA Technical Reports Server (NTRS)

Kennedy, Kriss J.

1990-01-01

This paper is part of an ongoing study on the interior design of a lunar outpost habitat facility. The concept presented represents the work done up to and including August 1989. This concept is part of NASA's ongoing effort to explore alternative options for planet surface systems habitation. Results of a volume analog study to determine the required pressurized volume are presented along with an internal layout of the habitat facility. The concept presented in this paper is a constructible lunar habitat that provides a living and working environment for a crew of 12. It is a 16-m diameter spherical pneumatic structure which contains 2145 cubic meters of volume. Five levels of living and working areas make up the 742 sq m of floor space. A 2-m vertical circulation shaft at the center allows for transfer of crew and equipment.

KSC-04pd1563

NASA Image and Video Library

2004-07-26

KENNEDY SPACE CENTER, FLA. - Sen. Bill Nelson (right), D-Fla., explains the layout of the glass cockpit to Sen. John F. Kerry, D-Mass., on the flight deck of orbiter Discovery during a tour of the Orbiter Processing Facility (OPF). The “bunny suits” they are wearing are clean room attire required for anyone coming in close proximity to Discovery, currently being prepared for flight on the next Space Shuttle mission. The tour of the OPF follows a public meeting Kerry held at the Dr. Kurt H. Debus Conference Facility at the Kennedy Space Center Visitor Complex. He said he chose to speak at KSC because it symbolizes America’s commitment to science, innovation and technology. He and Sen. John Edwards, D-N.C., are on a speaking tour prior to their appearance at the Democratic National Convention in Boston.

Mars habitat

NASA Technical Reports Server (NTRS)

Ayers, Dale; Barnes, Timothy; Bryant, Woody; Chowdhury, Parveen; Dillard, Joe; Gardner, Vernadette; Gregory, George; Harmon, Cheryl; Harrell, Brock; Hilton, Sherrill

1991-01-01

The objective of this study is to develop a conceptual design for a permanently manned, self-sustaining Martian facility, to accommodate a crew of 20 people. The goal is to incorporate the major functions required for long term habitation in the isolation of a barren planet into a thriving ecosystem. These functions include living, working, service, and medical facilities as well as a green house. The main design task was to focus on the internal layout while investigating the appropriate structure, materials, and construction techniques. The general concept was to create a comfortable, safe living environment for the crew members for a stay of six to twelve months on Mars. Two different concepts were investigated, a modular assembly reusable structure (MARS) designated Lavapolis, and a prefabricated space frame structure called Hexamars. Both models take into account factors such as future expansion, radiation shielding, and ease of assembly.

Assistive peripheral phosphene arrays deliver advantages in obstacle avoidance in simulated end-stage retinitis pigmentosa: a virtual-reality study

NASA Astrophysics Data System (ADS)

Zapf, Marc Patrick H.; Boon, Mei-Ying; Lovell, Nigel H.; Suaning, Gregg J.

2016-04-01

Objective. The prospective efficacy of peripheral retinal prostheses for guiding orientation and mobility in the absence of residual vision, as compared to an implant for the central visual field (VF), was evaluated using simulated prosthetic vision (SPV). Approach. Sighted volunteers wearing a head-mounted display performed an obstacle circumvention task under SPV. Mobility and orientation performance with three layouts of prosthetic vision were compared: peripheral prosthetic vision of higher visual acuity (VA) but limited VF, of wider VF but limited VA, as well as centrally restricted prosthetic vision. Learning curves using these layouts were compared fitting an exponential model to the mobility and orientation measures. Main results. Using peripheral layouts, performance was superior to the central layout. Walking speed with both higher-acuity and wider-angle layouts was 5.6% higher, and mobility errors reduced by 46.4% and 48.6%, respectively, as compared to the central layout. The wider-angle layout yielded the least number of collisions, 63% less than the higher-acuity and 73% less than the central layout. Using peripheral layouts, the number of visual-scanning related head movements was 54.3% (higher-acuity) and 60.7% (wider-angle) lower, as compared to the central layout, and the ratio of time standing versus time walking was 51.9% and 61.5% lower, respectively. Learning curves did not differ between layouts, except for time standing versus time walking, where both peripheral layouts achieved significantly lower asymptotic values compared to the central layout. Significance. Beyond complementing residual vision for an improved performance, peripheral prosthetic vision can effectively guide mobility in the later stages of retinitis pigmentosa (RP) without residual vision. Further, the temporal dynamics of learning peripheral and central prosthetic vision are similar. Therefore, development of a peripheral retinal prosthesis and early implantation to alleviate VF constriction in RP should be considered to extend the target group and the time of benefit for potential retinal prosthesis implantees.

14 CFR 77.2 - Definition of terms.

Code of Federal Regulations, 2011 CFR

2011-01-01

... approach system is planned and is so indicated by an FAA approved airport layout plan; a military service approved military airport layout plan; any other FAA planning document, or military service military... layout plan, a military service approved military airport layout plan, or by any planning document...

Impact of data layouts on the efficiency of GPU-accelerated IDW interpolation.

PubMed

Mei, Gang; Tian, Hong

2016-01-01

This paper focuses on evaluating the impact of different data layouts on the computational efficiency of GPU-accelerated Inverse Distance Weighting (IDW) interpolation algorithm. First we redesign and improve our previous GPU implementation that was performed by exploiting the feature of CUDA dynamic parallelism (CDP). Then we implement three versions of GPU implementations, i.e., the naive version, the tiled version, and the improved CDP version, based upon five data layouts, including the Structure of Arrays (SoA), the Array of Structures (AoS), the Array of aligned Structures (AoaS), the Structure of Arrays of aligned Structures (SoAoS), and the Hybrid layout. We also carry out several groups of experimental tests to evaluate the impact. Experimental results show that: the layouts AoS and AoaS achieve better performance than the layout SoA for both the naive version and tiled version, while the layout SoA is the best choice for the improved CDP version. We also observe that: for the two combined data layouts (the SoAoS and the Hybrid), there are no notable performance gains when compared to other three basic layouts. We recommend that: in practical applications, the layout AoaS is the best choice since the tiled version is the fastest one among three versions. The source code of all implementations are publicly available.

Integrated manufacturing flow for selective-etching SADP/SAQP

NASA Astrophysics Data System (ADS)

Ali, Rehab Kotb; Fatehy, Ahmed Hamed; Word, James

2018-03-01

Printing cut mask in SAMP (Self Aligned Multi Patterning) is very challenging at advanced nodes. One of the proposed solutions is to print the cut shapes selectively. Which means the design is decomposed into mandrel tracks, Mandrel cuts and non-Mandrel cuts. The mandrel and non-Mandrel cuts are mutually independent which results in relaxing spacing constrains and as a consequence more dense metal lines. In this paper, we proposed the manufacturing flow of selective etching process. The results are quantified in terms of measuring PVBand, EPE and the number of hard bridging and pinching across the layout.

The effect of design modifications to the typographical layout of the New York State elementary science learning standards on user preference and process time

NASA Astrophysics Data System (ADS)

Arnold, Jeffery E.

The purpose of this study was to determine the effect of four different design layouts of the New York State elementary science learning standards on user processing time and preference. Three newly developed layouts contained the same information as the standards core curriculum. In this study, the layout of the core guide is referred to as Book. The layouts of the new documents are referred to as Chart, Map, and Tabloid based on the format used to convey content hierarchy information. Most notably, all the new layouts feature larger page sizes, color, page tabs, and an icon based navigation system (IBNS). A convenience sample of 48 New York State educators representing three educator types (16 pre-service teachers, 16 in-service teachers, and 16 administrators) participated in the study. After completing timed tasks accurately, participants scored each layout based on preference. Educator type and layout were the independent variables, and process time and user preference were the dependent variables. A two-factor experimental design with Educator Type as the between variable and with repeated measures on Layout, the within variable, showed a significant difference in process time for Educator Type and Layout. The main effect for Educator Type (F(2, 45) = 8.03, p <.001) was significant with an observed power of .94, and an effect size of .26. The pair-wise comparisons for process time showed that pre-service teachers (p = .02) and administrators (p =.009) completed the assigned tasks more quickly when compared to in-service teachers. The main effect for Layout (F(3, 135) = 4.47, p =.01) was also significant with an observed power of .80, and an effect size of .09. Pair-wise comparisons showed that the newly developed Chart (p = .019) and Map (p = .032) layouts reduced overall process time when compared to the existing state learning standards (Book). The Layout X Educator type interaction was not significant. The same two-factor experimental design on preference, showed the main effect for Layout (F(3, 135) = 28.43, p =.001) was significant. The observed power was 1.0, with an effect size of .39. Pair-wise comparisons for preference scores showed that the Chart (p = .001), Map (p = .001), and Tabloid (p = .001) were preferred over the Book layout. The Layout Type X Educator Type interaction and the main effect for Educator Type were not significant. This study provides evidence that the newly developed design layouts improve usability (as measured by process time and preference scores) of the New York State elementary science learning standard documents. Features in the new layout design, such as the IBNS, may provide a foundation for a visual language and aid users in navigating standard documents across grade level and subject areas. Implications for the next generation of standard documents are presented.

A multilevel layout algorithm for visualizing physical and genetic interaction networks, with emphasis on their modular organization.

PubMed

Tuikkala, Johannes; Vähämaa, Heidi; Salmela, Pekka; Nevalainen, Olli S; Aittokallio, Tero

2012-03-26

Graph drawing is an integral part of many systems biology studies, enabling visual exploration and mining of large-scale biological networks. While a number of layout algorithms are available in popular network analysis platforms, such as Cytoscape, it remains poorly understood how well their solutions reflect the underlying biological processes that give rise to the network connectivity structure. Moreover, visualizations obtained using conventional layout algorithms, such as those based on the force-directed drawing approach, may become uninformative when applied to larger networks with dense or clustered connectivity structure. We implemented a modified layout plug-in, named Multilevel Layout, which applies the conventional layout algorithms within a multilevel optimization framework to better capture the hierarchical modularity of many biological networks. Using a wide variety of real life biological networks, we carried out a systematic evaluation of the method in comparison with other layout algorithms in Cytoscape. The multilevel approach provided both biologically relevant and visually pleasant layout solutions in most network types, hence complementing the layout options available in Cytoscape. In particular, it could improve drawing of large-scale networks of yeast genetic interactions and human physical interactions. In more general terms, the biological evaluation framework developed here enables one to assess the layout solutions from any existing or future graph drawing algorithm as well as to optimize their performance for a given network type or structure. By making use of the multilevel modular organization when visualizing biological networks, together with the biological evaluation of the layout solutions, one can generate convenient visualizations for many network biology applications.

48 CFR 36.517 - Layout of work.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 48 Federal Acquisition Regulations System 1 2010-10-01 2010-10-01 false Layout of work. 36.517... CONTRACTING CONSTRUCTION AND ARCHITECT-ENGINEER CONTRACTS Contract Clauses 36.517 Layout of work. The contracting officer shall insert the clause at 52.236-17, Layout of Work, in solicitations and contracts when...

48 CFR 36.517 - Layout of work.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 48 Federal Acquisition Regulations System 1 2011-10-01 2011-10-01 false Layout of work. 36.517... CONTRACTING CONSTRUCTION AND ARCHITECT-ENGINEER CONTRACTS Contract Clauses 36.517 Layout of work. The contracting officer shall insert the clause at 52.236-17, Layout of Work, in solicitations and contracts when...

CIVIL TECHNOLOGY, HIGHWAY AND STRUCTURAL OPTIONS, A SUGGESTED 2-YEAR POST HIGH SCHOOL CURRICULUM. TECHNICAL EDUCATION PROGRAM SERIES, NUMBER 8.

ERIC Educational Resources Information Center

BEAUMONT, JOHN A; AND OTHERS

DESIGNED TO ASSIST ADMINISTRATORS, SUPERVISORS, AND TEACHERS TO PLAN, DEVELOP, AND EVALUATE PROGRAMS, THIS CURRICULUM GUIDE OFFERS COURSE OUTLINES, PROCEDURES, LABORATORY LAYOUTS, TEXTS AND REFERENCES, LISTS OF LABORATORY EQUIPMENT AND ITS COST, AND A SELECTED LIST OF SCIENTIFIC AND TECHNICAL SOCIETIES. BASIC MATERIALS WERE PREPARED AT THE…

New PDC cutters improve drilling efficiency

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mensa-Wilmot, G.

1997-10-27

New polycrystalline diamond compact (PDC) cutters increase penetration rates and cumulative footage through improved abrasion, impact, interface strength, thermal stability, and fatigue characteristics. Studies of formation characterization, vibration analysis, hydraulic layouts, and bit selection continue to improve and expand PDC bit applications. The paper discusses development philosophy, performance characteristics and requirements, Types A, B, and C cutters, and combinations.

The Mission of "La Prensa": Informing a Layout of the Literature of Hispanic New York

ERIC Educational Resources Information Center

Galasso, Regina

2012-01-01

The Hispanic literature of New York has often been classified as belonging to a handful of canonical authors or selected national groups. However, examples from the early years of the newspaper "La Prensa" and Felipe Alfau's novel "Chromos", as well as consideration for New York's cultural climate during the first decades of…

Materials for programmed, functional transformation in transient electronic systems.

PubMed

Hwang, Suk-Won; Kang, Seung-Kyun; Huang, Xian; Brenckle, Mark A; Omenetto, Fiorenzo G; Rogers, John A

2015-01-07

Materials and device designs are presented for electronic systems that undergo functional transformation by a controlled time sequence in the dissolution of active materials and/or encapsulation layers. Demonstration examples include various biocompatible, multifunctional systems with autonomous behavior defined by materials selection and layout. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

A NASTRAN Model of a Large Flexible Swing-Wing Bomber. Volume 1: NASTRAN Model Plane

NASA Technical Reports Server (NTRS)

Mock, W. D.

1982-01-01

A review was conducted of B-1 aircraft no. 2 (A/C-2) internal loads models to determine the minimum model complexity necessary to fulfill all of the airloads research study objectives. Typical model sizings were tabulated at selected vehicle locations, and scale layouts were prepared of the NASTRAN structural analysis model.

Microfilming of the Texas Women: A Celebration of History Exhibit Archives in the Texas Woman's University Library.

ERIC Educational Resources Information Center

Nicewarner, Metta

1988-01-01

Description of the microfilming of a women's studies archive at the Texas Woman's University Library discusses: (1) project background; (2) criteria for equipment purchase; (3) equipment selected; (4) recommended resources; (5) indexing and layout decisions; (6) the filming process; and (7) the pros and cons of in-house microreproduction. (three…

Marker optimization for facial motion acquisition and deformation.

PubMed

Le, Binh H; Zhu, Mingyang; Deng, Zhigang

2013-11-01

A long-standing problem in marker-based facial motion capture is what are the optimal facial mocap marker layouts. Despite its wide range of potential applications, this problem has not yet been systematically explored to date. This paper describes an approach to compute optimized marker layouts for facial motion acquisition as optimization of characteristic control points from a set of high-resolution, ground-truth facial mesh sequences. Specifically, the thin-shell linear deformation model is imposed onto the example pose reconstruction process via optional hard constraints such as symmetry and multiresolution constraints. Through our experiments and comparisons, we validate the effectiveness, robustness, and accuracy of our approach. Besides guiding minimal yet effective placement of facial mocap markers, we also describe and demonstrate its two selected applications: marker-based facial mesh skinning and multiresolution facial performance capture.

Long term orbital storage of cryogenic propellants for advanced space transportation missions

NASA Technical Reports Server (NTRS)

Schuster, John R.; Brown, Norman S.

1987-01-01

A comprehensive study has developed the major features of a large capacity orbital propellant depot for the space-based, cryogenic OTV. The study has treated both the Dual-Keel Space Station and co-orbiting platforms as the accommodations base for the propellant storage facilities, and trades have examined both tethered and hard-docked options. Five tank set concepts were developed for storing the propellants, and along with layout options for the station and platform, were evaluated from the standpoints of servicing, propellant delivery, boiloff, micrometeoroid/debris shielding, development requirements, and cost. These trades led to the recommendation that an all-passive storage concept be considered for the platform and an actively refrigerated concept providing for reliquefaction of all boiloff be considered for the Space Station. The tank sets are modular, each storing up to 45,400 kg of LO2/LH2, and employ many advanced features to provide for microgravity fluid management and to limit boiloff. The features include such technologies as zero-gravity mass gauging, total communication capillary liquid acquisition devices, autogenous pressurization, thermodynamic vent systems, thick multilayer insulation, vapor-cooled shields, solar-selective coatings, advanced micrometeoroid/debris protection systems, and long-lived cryogenic refrigeration systems.

Automatic layout of structured hierarchical reports.

PubMed

Bakke, Eirik; Karger, David R; Miller, Robert C

2013-12-01

Domain-specific database applications tend to contain a sizable number of table-, form-, and report-style views that must each be designed and maintained by a software developer. A significant part of this job is the necessary tweaking of low-level presentation details such as label placements, text field dimensions, list or table styles, and so on. In this paper, we present a horizontally constrained layout management algorithm that automates the display of structured hierarchical data using the traditional visual idioms of hand-designed database UIs: tables, multi-column forms, and outline-style indented lists. We compare our system with pure outline and nested table layouts with respect to space efficiency and readability, the latter with an online user study on 27 subjects. Our layouts are 3.9 and 1.6 times more compact on average than outline layouts and horizontally unconstrained table layouts, respectively, and are as readable as table layouts even for large datasets.

Native conflict awared layout decomposition in triple patterning lithography using bin-based library matching method

NASA Astrophysics Data System (ADS)

Ke, Xianhua; Jiang, Hao; Lv, Wen; Liu, Shiyuan

2016-03-01

Triple patterning (TP) lithography becomes a feasible technology for manufacturing as the feature size further scale down to sub 14/10 nm. In TP, a layout is decomposed into three masks followed with exposures and etches/freezing processes respectively. Previous works mostly focus on layout decomposition with minimal conflicts and stitches simultaneously. However, since any existence of native conflict will result in layout re-design/modification and reperforming the time-consuming decomposition, the effective method that can be aware of native conflicts (NCs) in layout is desirable. In this paper, a bin-based library matching method is proposed for NCs detection and layout decomposition. First, a layout is divided into bins and the corresponding conflict graph in each bin is constructed. Then, we match the conflict graph in a prebuilt colored library, and as a result the NCs can be located and highlighted quickly.

Reference Frames during the Acquisition and Development of Spatial Memories

ERIC Educational Resources Information Center

Kelly, Jonathan W.; McNamara, Timothy P.

2010-01-01

Four experiments investigated the role of reference frames during the acquisition and development of spatial knowledge, when learning occurs incrementally across views. In two experiments, participants learned overlapping spatial layouts. Layout 1 was first studied in isolation, and Layout 2 was later studied in the presence of Layout 1. The…

Designing for Communication: The Key to Successful Desktop Publishing.

ERIC Educational Resources Information Center

McCain, Ted D. E.

Written for those who are new to design and page layout, this book focuses on providing novice desktop publishers with an understanding of communication, graphic design, typography, page layout, and page layout techniques. The book also discusses how people read, design as a consequence of understanding, and the principles of page layout. Chapters…

Schematic driven layout of Reed Solomon encoders

NASA Technical Reports Server (NTRS)

Arave, Kari; Canaris, John; Miles, Lowell; Whitaker, Sterling

1992-01-01

Two Reed Solomon error correcting encoders are presented. Schematic driven layout tools were used to create the encoder layouts. Special consideration had to be given to the architecture and logic to provide scalability of the encoder designs. Knowledge gained from these projects was used to create a more flexible schematic driven layout system.

Automatic page layout using genetic algorithms for electronic albuming

NASA Astrophysics Data System (ADS)

Geigel, Joe; Loui, Alexander C. P.

2000-12-01

In this paper, we describe a flexible system for automatic page layout that makes use of genetic algorithms for albuming applications. The system is divided into two modules, a page creator module which is responsible for distributing images amongst various album pages, and an image placement module which positions images on individual pages. Final page layouts are specified in a textual form using XML for printing or viewing over the Internet. The system makes use of genetic algorithms, a class of search and optimization algorithms that are based on the concepts of biological evolution, for generating solutions with fitness based on graphic design preferences supplied by the user. The genetic page layout algorithm has been incorporated into a web-based prototype system for interactive page layout over the Internet. The prototype system is built using client-server architecture and is implemented in java. The system described in this paper has demonstrated the feasibility of using genetic algorithms for automated page layout in albuming and web-based imaging applications. We believe that the system adequately proves the validity of the concept, providing creative layouts in a reasonable number of iterations. By optimizing the layout parameters of the fitness function, we hope to further improve the quality of the final layout in terms of user preference and computation speed.

A multilevel layout algorithm for visualizing physical and genetic interaction networks, with emphasis on their modular organization

PubMed Central

2012-01-01

Background Graph drawing is an integral part of many systems biology studies, enabling visual exploration and mining of large-scale biological networks. While a number of layout algorithms are available in popular network analysis platforms, such as Cytoscape, it remains poorly understood how well their solutions reflect the underlying biological processes that give rise to the network connectivity structure. Moreover, visualizations obtained using conventional layout algorithms, such as those based on the force-directed drawing approach, may become uninformative when applied to larger networks with dense or clustered connectivity structure. Methods We implemented a modified layout plug-in, named Multilevel Layout, which applies the conventional layout algorithms within a multilevel optimization framework to better capture the hierarchical modularity of many biological networks. Using a wide variety of real life biological networks, we carried out a systematic evaluation of the method in comparison with other layout algorithms in Cytoscape. Results The multilevel approach provided both biologically relevant and visually pleasant layout solutions in most network types, hence complementing the layout options available in Cytoscape. In particular, it could improve drawing of large-scale networks of yeast genetic interactions and human physical interactions. In more general terms, the biological evaluation framework developed here enables one to assess the layout solutions from any existing or future graph drawing algorithm as well as to optimize their performance for a given network type or structure. Conclusions By making use of the multilevel modular organization when visualizing biological networks, together with the biological evaluation of the layout solutions, one can generate convenient visualizations for many network biology applications. PMID:22448851

BEaTriX, expanded x-ray beam facility for testing modular elements of telescope optics: an update

NASA Astrophysics Data System (ADS)

Pelliciari, C.; Spiga, D.; Bonnini, E.; Buffagni, E.; Ferrari, C.; Pareschi, G.; Tagliaferri, G.

2015-09-01

We present in this paper an update on the design of BEaTriX (Beam Expander Testing X-ray facility), an X-ray apparatus to be realized at INAF/OAB and that will generate an expanded, uniform and parallel beam of soft X-rays. BEaTriX will be used to perform the functional tests of X-ray focusing modules of large X-ray optics such as those for the ATHENA X-ray observatory, using the Silicon Pore Optics (SPO) as a baseline technology, and Slumped Glass Optics (SGO) as a possible alternative. Performing the tests in X-rays provides the advantage of an in-situ, at-wavelength quality control of the optical modules produced in series by the industry, performing a selection of the modules with the best angular resolution, and, in the case of SPOs, there is also the interesting possibility to align the parabolic and the hyperbolic stacks directly under X-rays, to minimize the aberrations. However, a parallel beam with divergence below 2 arcsec is necessary in order to measure mirror elements that are expected to reach an angular resolution of about 4 arcsec, since the ATHENA requirement for the entire telescope is 5 arcsec. Such a low divergence over the typical aperture of modular optics would require an X-ray source to be located in a several kilometers long vacuum tube. In contrast, BEaTriX will be compact enough (5 m x 14 m) to be housed in a small laboratory, will produce an expanded X-ray beam 60 mm x 200 mm broad, characterized by a very low divergence (1.5 arcsec HEW), strong polarization, high uniformity, and X-ray energy selectable between 1.5 keV and 4.5 keV. In this work we describe the BEaTriX layout and show a performance simulation for the X-ray energy of 4.5 keV.

Air-kerma evaluation at the maze entrance of HDR brachytherapy facilities.

PubMed

Pujades, M C; Granero, D; Vijande, J; Ballester, F; Perez-Calatayud, J; Papagiannis, P; Siebert, F A

2014-12-01

In the absence of procedures for evaluating the design of brachytherapy (BT) facilities for radiation protection purposes, the methodology used for external beam radiotherapy facilities is often adapted. The purpose of this study is to adapt the NCRP 151 methodology for estimating the air-kerma rate at the door in BT facilities. Such methodology was checked against Monte Carlo (MC) techniques using the code Geant4. Five different facility designs were studied for (192)Ir and (60)Co HDR applications to account for several different bunker layouts.For the estimation of the lead thickness needed at the door, the use of transmission data for the real spectra at the door instead of the ones emitted by (192)Ir and (60)Co will reduce the lead thickness by a factor of five for (192)Ir and ten for (60)Co. This will significantly lighten the door and hence simplify construction and operating requirements for all bunkers.The adaptation proposed in this study to estimate the air-kerma rate at the door depends on the complexity of the maze: it provides good results for bunkers with a maze (i.e. similar to those used for linacs for which the NCRP 151 methodology was developed) but fails for less conventional designs. For those facilities, a specific Monte Carlo study is in order for reasons of safety and cost-effectiveness.

Space Launch System Base Heating Test: Environments and Base Flow Physics

NASA Technical Reports Server (NTRS)

Mehta, Manish; Knox, Kyle; Seaford, Mark; Dufrene, Aaron

2016-01-01

NASA MSFC and CUBRC designed and developed a 2% scale SLS propulsive wind tunnel test program to investigate base flow effects during flight from lift-off to MECO. This type of test program has not been conducted in 40+ years during the NASA Shuttle Program. Dufrene et al paper described the operation, instrumentation type and layout, facility and propulsion performance, test matrix and conditions and some raw results. This paper will focus on the SLS base flow physics and the generation and results of the design environments being used to design the thermal protection system.

Random Access Frame (RAF) System Neutral Buoyancy Evaluations

NASA Technical Reports Server (NTRS)

Howe, A. Scott; Polit-Casillas, Raul; Akin, David L.; McBryan, Katherine; Carlsen, Christopher

2015-01-01

The Random Access Frame (RAF) concept is a system for organizing internal layouts of space habitats, vehicles, and outposts. The RAF system is designed as a more efficient improvement over the current International Standard Payload Rack (ISPR) used on the International Space Station (ISS), which was originally designed to allow for swapping and resupply by the Space Shuttle. The RAF system is intended to be applied in variable gravity or microgravity environments. This paper discusses evaluations and results of testing the RAF system in a neutral buoyancy facility simulating low levels of gravity that might be encountered in a deep space environment.

Health knowledge, attitudes and practices of family planning service providers and clients in Akwapim North District of Ghana.

PubMed

Atuahene, Margaret Duah; Afari, Esther Oku; Adjuik, Martin; Obed, Samuel

2016-01-01

Family planning services help save lives by reducing women's exposure to risks of child birth and abortion. While family planning services provide measures to prevent unintended pregnancies and time the formation of families, the acceptability and coverage is still very low worldwide. Some of the reasons for this include poor quality of service, unavailability of range of methods, fear of opposition from partners, side effects and health concerns among others.About 40 % of the world's 215,000 annual deaths in childbirth occur in the Sub-Saharan region. In Ghana, urban-rural fertility differences range from two to three children. The acceptability and coverage of family planning are still low and in the study area in particular. We sought to examine factors that contribute to low acceptability and coverage of family planning services in a sub-urban community with a design of quantitative cross-sectional. Ethical approval was given by the Ghana Health Service. Midwives and community health nurses who provide family planning services were interviewed. Exit-interview was also conducted with women receiving a variety of outpatient services. Most of the women in this study (48.7 %) were in the 25-34 age range and were either married (42.8 %) or cohabiting (40.5 %). Majority of these women (67.7 %) have middle/Junior high level of formal education with a modal parity of two. Sixty eight (68) clients were identified as current family planning users. About 6.0 % and 4.5 % were dissatisfied about auditory and visual privacy during counselling respectively. This was confirmed by providers who attributed it to inappropriate facility layout. Most of the clients (79.1 %) were not given educational materials although 88.8 % were talked to about family planning and this could be due to unavailability of these hand-outs.Though clients show satisfaction of services received, providers did not follow standard protocols with as much as 73.7 % faced with challenges in provision of services which were attributed to improper facility layout and lack of furniture. About 77.2 % were willing to provide short term methods, while 91.2 % wanted to provide long term methods. As much as 93.3 % of the women said they would have liked providers give more detailed information on family planning. While most of the women (88.3 %) used injectables, only 6.1 % and 0.9 % used Implants and IUD respectively. Finding ways to improve client privacy through good facility layout will ensure visual and auditory privacy to enhance family planning service provision and uptake. Continuous competency training will assist providers design innovative action plans and meet client satisfaction needs.

Optimal Control Surface Layout for an Aeroservoelastic Wingbox

NASA Technical Reports Server (NTRS)

Stanford, Bret K.

2017-01-01

This paper demonstrates a technique for locating the optimal control surface layout of an aeroservoelastic Common Research Model wingbox, in the context of maneuver load alleviation and active utter suppression. The combinatorial actuator layout design is solved using ideas borrowed from topology optimization, where the effectiveness of a given control surface is tied to a layout design variable, which varies from zero (the actuator is removed) to one (the actuator is retained). These layout design variables are optimized concurrently with a large number of structural wingbox sizing variables and control surface actuation variables, in order to minimize the sum of structural weight and actuator weight. Results are presented that demonstrate interdependencies between structural sizing patterns and optimal control surface layouts, for both static and dynamic aeroelastic physics.

[An investigation of the application of hygienic standards for the design of industrial enterprises (GBZ 1-2010)].

PubMed

Lu, Y; Zhang, M

2016-08-20

Objective: To study the applicability, the high frequency used content, the feasibility, and issues needed to be solved of the standard of GBZ 1-2010, aiming to provide technical evidence for the revision of GBZ1. Methods: In the study, the data were collected by referring to the literature database and the questionnaire from June 2013 to June 2015. There were 2 surveys carried out in the study, with methods including questionnaire survey and specific interview. The investigation methods include the paper version of the questionnaire by mail, the electronic version of the questionnaire by e-mail, and the online survey. And 111 questionnaires were collected. Results: In total, the applicability survey (the first survey) received 156 suggestions covering 76 items from 23 facilities, and 13 key technical issues were summarized to be solved as priorities. In the application survey (the second survey) , the leading three jobs using GBZ 1-2010 were the occupational hazards evaluation for constructive project (82.0%) , lecturing/training (65.8%) , occupational hazards monitoring (64.9%) , respectively. The high frequency used contents of GBZ 1-2010 were the sixth part "the basic hygienic requirements for workplace" (90.1%) , the fifth part "site selection, overall layout and workshop design" (87.4%) , the seventh part "the basic hygienic requirements for welfare room" (85.6%) , respectively. In the results of feasibility, scores of the fourth part "the general rules" , the fifth part "site selection, overall layout and workshop design" , the sixth part "the basic hygienic requirements for workplace" , the seventh part "the basic hygienic requirements for welfare room" , the eighth "emergency rescue" , annex A "the correct use instructions" , annex B "buffer zone standards for industrial enterprises" were 2.6, 3.1, 3.5, 3.8, 3.2, 3.3, 2.6, respectively. Among 111 questionnaires, the parts needed to be modified as priories were the fifth part "site selection, overall layout and workshop design" (51.4%) , and the sixth part "the basic hygienic requirements for workplace" (51.4%) . In results of the key technical issues needed to be modified of GBZ 1-2010, the contents needed to be added as priories were the occupational prevention and control requirements of biological factors (51.4%) , technical parameters of dust in workplace (48.7%) , technical parameters of hazardous agents in workplace (46.9%) , the quality and quantity requirements of fresh air (46.0%) , the setting conditions of the emergency rescue station (46.0%) , the hygienic design requirements of joint workshops and the evidence (45.1%) , and requirements for medical emergency rescue personnel equipped and qualified (45.1%) . Conclusion: GBZ 1-2010 is feasible and practical, mainly used by occupational health technical service organizations in the occupational hazards evaluation for constructive project, lecturing/training, occupational hazards monitoring, et al. GBZ 1 plays a directive role in government decision-making, control of constructive projects from the beginning, training and capacity building of occupational health professionals, and the prevention and treatment of occupational diseases in enterprises, needing to strengthen the implementation of GBZ 1. And on the basis of the above key technical issues to be revised, international cooperation and exchanges should be strengthened, so that it is adapted to the development of the modern enterprise system.

DeDaL: Cytoscape 3 app for producing and morphing data-driven and structure-driven network layouts.

PubMed

Czerwinska, Urszula; Calzone, Laurence; Barillot, Emmanuel; Zinovyev, Andrei

2015-08-14

Visualization and analysis of molecular profiling data together with biological networks are able to provide new mechanistic insights into biological functions. Currently, it is possible to visualize high-throughput data on top of pre-defined network layouts, but they are not always adapted to a given data analysis task. A network layout based simultaneously on the network structure and the associated multidimensional data might be advantageous for data visualization and analysis in some cases. We developed a Cytoscape app, which allows constructing biological network layouts based on the data from molecular profiles imported as values of node attributes. DeDaL is a Cytoscape 3 app, which uses linear and non-linear algorithms of dimension reduction to produce data-driven network layouts based on multidimensional data (typically gene expression). DeDaL implements several data pre-processing and layout post-processing steps such as continuous morphing between two arbitrary network layouts and aligning one network layout with respect to another one by rotating and mirroring. The combination of all these functionalities facilitates the creation of insightful network layouts representing both structural network features and correlation patterns in multivariate data. We demonstrate the added value of applying DeDaL in several practical applications, including an example of a large protein-protein interaction network. DeDaL is a convenient tool for applying data dimensionality reduction methods and for designing insightful data displays based on data-driven layouts of biological networks, built within Cytoscape environment. DeDaL is freely available for downloading at http://bioinfo-out.curie.fr/projects/dedal/.

Factors influencing experience in crowds - The participant perspective.

PubMed

Filingeri, Victoria; Eason, Ken; Waterson, Patrick; Haslam, Roger

2017-03-01

Humans encounter crowd situations on a daily basis, resulting in both negative and positive experiences. Understanding how to optimise the participant experience of crowds is important. In the study presented in this paper, 5 focus groups were conducted (35 participants, age range: 21-71 years) and 55 crowd situations observed (e.g. transport hubs, sport events, retail situations). Influences on participant experience in crowds identified by the focus groups and observations included: physical design of crowd space and facilities (layout, queuing strategies), crowd movement (monitoring capacity, pedestrian flow), communication and information (signage, wayfinding), comfort and welfare (provision of facilities, environmental comfort), and public order. It was found that important aspects affecting participant experience are often not considered systematically in the planning of events or crowd situations. The findings point to human factors aspects of crowds being overlooked, with the experiences of participants often poor. Copyright © 2016. Published by Elsevier Ltd.

Pathway collages: personalized multi-pathway diagrams.

PubMed

Paley, Suzanne; O'Maille, Paul E; Weaver, Daniel; Karp, Peter D

2016-12-13

Metabolic pathway diagrams are a classical way of visualizing a linked cascade of biochemical reactions. However, to understand some biochemical situations, viewing a single pathway is insufficient, whereas viewing the entire metabolic network results in information overload. How do we enable scientists to rapidly construct personalized multi-pathway diagrams that depict a desired collection of interacting pathways that emphasize particular pathway interactions? We define software for constructing personalized multi-pathway diagrams called pathway-collages using a combination of manual and automatic layouts. The user specifies a set of pathways of interest for the collage from a Pathway/Genome Database. Layouts for the individual pathways are generated by the Pathway Tools software, and are sent to a Javascript Pathway Collage application implemented using Cytoscape.js. That application allows the user to re-position pathways; define connections between pathways; change visual style parameters; and paint metabolomics, gene expression, and reaction flux data onto the collage to obtain a desired multi-pathway diagram. We demonstrate the use of pathway collages in two application areas: a metabolomics study of pathogen drug response, and an Escherichia coli metabolic model. Pathway collages enable facile construction of personalized multi-pathway diagrams.

A Tool for the Automated Design and Evaluation of Habitat Interior Layouts

NASA Technical Reports Server (NTRS)

Simon, Matthew A.; Wilhite, Alan W.

2013-01-01

The objective of space habitat design is to minimize mass and system size while providing adequate space for all necessary equipment and a functional layout that supports crew health and productivity. Unfortunately, development and evaluation of interior layouts is often ignored during conceptual design because of the subjectivity and long times required using current evaluation methods (e.g., human-in-the-loop mockup tests and in-depth CAD evaluations). Early, more objective assessment could prevent expensive design changes that may increase vehicle mass and compromise functionality. This paper describes a new interior design evaluation method to enable early, structured consideration of habitat interior layouts. This interior layout evaluation method features a comprehensive list of quantifiable habitat layout evaluation criteria, automatic methods to measure these criteria from a geometry model, and application of systems engineering tools and numerical methods to construct a multi-objective value function measuring the overall habitat layout performance. In addition to a detailed description of this method, a C++/OpenGL software tool which has been developed to implement this method is also discussed. This tool leverages geometry modeling coupled with collision detection techniques to identify favorable layouts subject to multiple constraints and objectives (e.g., minimize mass, maximize contiguous habitable volume, maximize task performance, and minimize crew safety risks). Finally, a few habitat layout evaluation examples are described to demonstrate the effectiveness of this method and tool to influence habitat design.

Device Independent Layout and Style Editing Using Multi-Level Style Sheets

NASA Astrophysics Data System (ADS)

Dees, Walter

This paper describes a layout and styling framework that is based on the multi-level style sheets approach. It shows some of the techniques that can be used to add layout and style information to a UI in a device-independent manner, and how to reuse the layout and style information to create user interfaces for different devices

A grid layout algorithm for automatic drawing of biochemical networks.

PubMed

Li, Weijiang; Kurata, Hiroyuki

2005-05-01

Visualization is indispensable in the research of complex biochemical networks. Available graph layout algorithms are not adequate for satisfactorily drawing such networks. New methods are required to visualize automatically the topological architectures and facilitate the understanding of the functions of the networks. We propose a novel layout algorithm to draw complex biochemical networks. A network is modeled as a system of interacting nodes on squared grids. A discrete cost function between each node pair is designed based on the topological relation and the geometric positions of the two nodes. The layouts are produced by minimizing the total cost. We design a fast algorithm to minimize the discrete cost function, by which candidate layouts can be produced efficiently. A simulated annealing procedure is used to choose better candidates. Our algorithm demonstrates its ability to exhibit cluster structures clearly in relatively compact layout areas without any prior knowledge. We developed Windows software to implement the algorithm for CADLIVE. All materials can be freely downloaded from http://kurata21.bio.kyutech.ac.jp/grid/grid_layout.htm; http://www.cadlive.jp/ http://kurata21.bio.kyutech.ac.jp/grid/grid_layout.htm; http://www.cadlive.jp/

Penrose high-dynamic-range imaging

NASA Astrophysics Data System (ADS)

Li, Jia; Bai, Chenyan; Lin, Zhouchen; Yu, Jian

2016-05-01

High-dynamic-range (HDR) imaging is becoming increasingly popular and widespread. The most common multishot HDR approach, based on multiple low-dynamic-range images captured with different exposures, has difficulties in handling camera and object movements. The spatially varying exposures (SVE) technology provides a solution to overcome this limitation by obtaining multiple exposures of the scene in only one shot but suffers from a loss in spatial resolution of the captured image. While aperiodic assignment of exposures has been shown to be advantageous during reconstruction in alleviating resolution loss, almost all the existing imaging sensors use the square pixel layout, which is a periodic tiling of square pixels. We propose the Penrose pixel layout, using pixels in aperiodic rhombus Penrose tiling, for HDR imaging. With the SVE technology, Penrose pixel layout has both exposure and pixel aperiodicities. To investigate its performance, we have to reconstruct HDR images in square pixel layout from Penrose raw images with SVE. Since the two pixel layouts are different, the traditional HDR reconstruction methods are not applicable. We develop a reconstruction method for Penrose pixel layout using a Gaussian mixture model for regularization. Both quantitative and qualitative results show the superiority of Penrose pixel layout over square pixel layout.

Task-specific performance effects with different numeric keypad layouts.

PubMed

Armand, Jenny T; Redick, Thomas S; Poulsen, Joan R

2014-07-01

Two commonly used keypad arrangements are the telephone and calculator layouts. The purpose of this study was to determine if entering different types of numeric information was quicker and more accurate with the telephone or the calculator layout on a computer keyboard numeric keypad. Fifty-seven participants saw a 10-digit numeric stimulus to type with a computer number keypad as quickly and as accurately as possible. Stimuli were presented in either a numerical [1,234,567,890] or phone [(123) 456-7890] format. The results indicated that participants' memory of the layout for the arrangement of keys on a telephone was significantly better than the layout of a calculator. In addition, the results showed that participants were more accurate when entering stimuli using the calculator keypad layout. Critically, participants' response times showed an interaction of stimulus format and keypad layout: participants were specifically slowed when entering numeric stimuli using a telephone keypad layout. Responses made using the middle row of keys were faster and more accurate than responses using the top and bottom row of keys. Implications for keypad design and cell phone usage are discussed. Copyright © 2013 Elsevier Ltd and The Ergonomics Society. All rights reserved.

Periodical Publishing in Wisconsin. Proceedings of the Conference on Periodical Publishing in Wisconsin (Madison, WI, May 11-12, 1978).

ERIC Educational Resources Information Center

Danky, James P., Ed.; And Others

The papers contained in this compilation were drawn from the proceedings of a 1978 conference on periodical publishing in Wisconsin. Papers in the first section of the collection deal with the basics of publishing and cover such topics as selecting articles, starting a new publication, mailing procedures, aesthetics and layout, and printing…

a Geographic Analysis of Optimal Signage Location Selection in Scenic Area

NASA Astrophysics Data System (ADS)

Ruan, Ling; Long, Ying; Zhang, Ling; Wu, Xiao Ling

2016-06-01

As an important part of the scenic area infrastructure services, signage guiding system plays an indispensable role in guiding the way and improving the quality of tourism experience. This paper proposes an optimal method in signage location selection and direction content design in a scenic area based on geographic analysis. The object of the research is to provide a best solution to arrange limited guiding boards in a tourism area to show ways arriving at any scenic spot from any entrance. There are four steps to achieve the research object. First, the spatial distribution of the junction of the scenic road, the passageway and the scenic spots is analyzed. Then, the count of scenic roads intersection on the shortest path between all entrances and all scenic spots is calculated. Next, combing with the grade of the scenic road and scenic spots, the importance of each road intersection is estimated quantitatively. Finally, according to the importance of all road intersections, the most suitable layout locations of signage guiding boards can be provided. In addition, the method is applied in the Ming Tomb scenic area in China and the result is compared with the existing signage guiding space layout.

Improvement of productivity in low volume production industry layout by using witness simulation software

NASA Astrophysics Data System (ADS)

Jaffrey, V.; Mohamed, N. M. Z. N.; Rose, A. N. M.

2017-10-01

In almost all manufacturing industry, increased productivity and better efficiency of the production line are the most important goals. Most factories especially small scale factory has less awareness of manufacturing system optimization and lack of knowledge about it and uses the traditional way of management. Problems that are commonly identified in the factory are a high idle time of labour and also small production. This study is done in a Small and Medium Enterprises (SME) low volume production company. Data collection and problems affecting productivity and efficiency are identified. In this study, Witness simulation software is being used to simulate the layout and the output is focusing on the improvement of layout in terms of productivity and efficiency. In this study, the layout is rearranged by reducing the travel time from a workstation to another workstation. Then, the improved layout is modelled and the machine and labour statistic of both, original and improved layout is taken. Productivity and efficiency are calculated for both layout and then being compared.

Using RGB-D sensors and evolutionary algorithms for the optimization of workstation layouts.

PubMed

Diego-Mas, Jose Antonio; Poveda-Bautista, Rocio; Garzon-Leal, Diana

2017-11-01

RGB-D sensors can collect postural data in an automatized way. However, the application of these devices in real work environments requires overcoming problems such as lack of accuracy or body parts' occlusion. This work presents the use of RGB-D sensors and genetic algorithms for the optimization of workstation layouts. RGB-D sensors are used to capture workers' movements when they reach objects on workbenches. Collected data are then used to optimize workstation layout by means of genetic algorithms considering multiple ergonomic criteria. Results show that typical drawbacks of using RGB-D sensors for body tracking are not a problem for this application, and that the combination with intelligent algorithms can automatize the layout design process. The procedure described can be used to automatically suggest new layouts when workers or processes of production change, to adapt layouts to specific workers based on their ways to do the tasks, or to obtain layouts simultaneously optimized for several production processes. Copyright © 2017 Elsevier Ltd. All rights reserved.

Combining Multiple Forms Of Visual Information To Specify Contact Relations In Spatial Layout

NASA Astrophysics Data System (ADS)

Sedgwick, Hal A.

1990-03-01

An expert system, called Layout2, has been described, which models a subset of available visual information for spatial layout. The system is used to examine detailed interactions between multiple, partially redundant forms of information in an environment-centered geometrical model of an environment obeying certain rather general constraints. This paper discusses the extension of Layout2 to include generalized contact relations between surfaces. In an environment-centered model, the representation of viewer-centered distance is replaced by the representation of environmental location. This location information is propagated through the representation of the environment by a network of contact relations between contiguous surfaces. Perspective information interacts with other forms of information to specify these contact relations. The experimental study of human perception of contact relations in extended spatial layouts is also discussed. Differences between human results and Layout2 results reveal limitations in the human ability to register available information; they also point to the existence of certain forms of information not yet formalized in Layout2.

Layout decomposition of self-aligned double patterning for 2D random logic patterning

NASA Astrophysics Data System (ADS)

Ban, Yongchan; Miloslavsky, Alex; Lucas, Kevin; Choi, Soo-Han; Park, Chul-Hong; Pan, David Z.

2011-04-01

Self-aligned double pattering (SADP) has been adapted as a promising solution for sub-30nm technology nodes due to its lower overlay problem and better process tolerance. SADP is in production use for 1D dense patterns with good pitch control such as NAND Flash memory applications, but it is still challenging to apply SADP to 2D random logic patterns. The favored type of SADP for complex logic interconnects is a two mask approach using a core mask and a trim mask. In this paper, we first describe layout decomposition methods of spacer-type double patterning lithography, then report a type of SADP compliant layouts, and finally report SADP applications on Samsung 22nm SRAM layout. For SADP decomposition, we propose several SADP-aware layout coloring algorithms and a method of generating lithography-friendly core mask patterns. Experimental results on 22nm node designs show that our proposed layout decomposition for SADP effectively decomposes any given layouts.

Exact solution for the optimal neuronal layout problem.

PubMed

Chklovskii, Dmitri B

2004-10-01

Evolution perfected brain design by maximizing its functionality while minimizing costs associated with building and maintaining it. Assumption that brain functionality is specified by neuronal connectivity, implemented by costly biological wiring, leads to the following optimal design problem. For a given neuronal connectivity, find a spatial layout of neurons that minimizes the wiring cost. Unfortunately, this problem is difficult to solve because the number of possible layouts is often astronomically large. We argue that the wiring cost may scale as wire length squared, reducing the optimal layout problem to a constrained minimization of a quadratic form. For biologically plausible constraints, this problem has exact analytical solutions, which give reasonable approximations to actual layouts in the brain. These solutions make the inverse problem of inferring neuronal connectivity from neuronal layout more tractable.

A Description of the Development, Capabilities, and Operational Status of the Test SLATE Data Acquisition System at the National Transonic Facility

NASA Technical Reports Server (NTRS)

Cramer, Christopher J.; Wright, James D.; Simmons, Scott A.; Bobbitt, Lynn E.; DeMoss, Joshua A.

2015-01-01

The paper will present a brief background of the previous data acquisition system at the National Transonic Facility (NTF) and the reasoning and goals behind the upgrade to the current Test SLATE (Test Software Laboratory and Automated Testing Environments) data acquisition system. The components, performance characteristics, and layout of the Test SLATE system within the NTF control room will be discussed. The development, testing, and integration of Test SLATE within NTF operations will be detailed. The operational capabilities of the system will be outlined including: test setup, instrumentation calibration, automatic test sequencer setup, data recording, communication between data and facility control systems, real time display monitoring, and data reduction. The current operational status of the Test SLATE system and its performance during recent NTF testing will be highlighted including high-speed, frame-by-frame data acquisition with conditional sampling post-processing applied. The paper concludes with current development work on the system including the capability for real-time conditional sampling during data acquisition and further efficiency enhancements to the wind tunnel testing process.

Preliminary design studies of an advanced general aviation aircraft

NASA Technical Reports Server (NTRS)

Barrett, Ron; Demoss, Shane; Dirkzwager, AB; Evans, Darryl; Gomer, Charles; Keiter, Jerry; Knipp, Darren; Seier, Glen; Smith, Steve; Wenninger, ED

1991-01-01

The preliminary design results are presented of the advanced aircraft design project. The goal was to take a revolutionary look into the design of a general aviation aircraft. Phase 1 of the project included the preliminary design of two configurations, a pusher, and a tractor. Phase 2 included the selection of only one configuration for further study. The pusher configuration was selected on the basis of performance characteristics, cabin noise, natural laminar flow, and system layouts. The design was then iterated to achieve higher levels of performance.

Site selection model for new metro stations based on land use

NASA Astrophysics Data System (ADS)

Zhang, Nan; Chen, Xuewu

2015-12-01

Since the construction of metro system generally lags behind the development of urban land use, sites of metro stations should adapt to their surrounding situations, which was rarely discussed by previous research on station layout. This paper proposes a new site selection model to find the best location for a metro station, establishing the indicator system based on land use and combining AHP with entropy weight method to obtain the schemes' ranking. The feasibility and efficiency of this model has been validated by evaluating Nanjing Shengtai Road station and other potential sites.

Application of Three Existing Stope Boundary Optimisation Methods in an Operating Underground Mine

NASA Astrophysics Data System (ADS)

Erdogan, Gamze; Yavuz, Mahmut

2017-12-01

The underground mine planning and design optimisation process have received little attention because of complexity and variability of problems in underground mines. Although a number of optimisation studies and software tools are available and some of them, in special, have been implemented effectively to determine the ultimate-pit limits in an open pit mine, there is still a lack of studies for optimisation of ultimate stope boundaries in underground mines. The proposed approaches for this purpose aim at maximizing the economic profit by selecting the best possible layout under operational, technical and physical constraints. In this paper, the existing three heuristic techniques including Floating Stope Algorithm, Maximum Value Algorithm and Mineable Shape Optimiser (MSO) are examined for optimisation of stope layout in a case study. Each technique is assessed in terms of applicability, algorithm capabilities and limitations considering the underground mine planning challenges. Finally, the results are evaluated and compared.

Processing sequence annotation data using the Lua programming language.

PubMed

Ueno, Yutaka; Arita, Masanori; Kumagai, Toshitaka; Asai, Kiyoshi

2003-01-01

The data processing language in a graphical software tool that manages sequence annotation data from genome databases should provide flexible functions for the tasks in molecular biology research. Among currently available languages we adopted the Lua programming language. It fulfills our requirements to perform computational tasks for sequence map layouts, i.e. the handling of data containers, symbolic reference to data, and a simple programming syntax. Upon importing a foreign file, the original data are first decomposed in the Lua language while maintaining the original data schema. The converted data are parsed by the Lua interpreter and the contents are stored in our data warehouse. Then, portions of annotations are selected and arranged into our catalog format to be depicted on the sequence map. Our sequence visualization program was successfully implemented, embedding the Lua language for processing of annotation data and layout script. The program is available at http://staff.aist.go.jp/yutaka.ueno/guppy/.

Research on layout and construction performance of cultural and creative industry parks in Xihu District of Hangzhou

NASA Astrophysics Data System (ADS)

Wang, Juan; Zhou, Jun

2018-05-01

Combing the current situation of cultural and creative industry parks in Xihu District of Hangzhou, analyzing the supporting elements of its layout, cultural and creative industry Pars in Xihu District have the characteristics of obvious group block distribution and the dominant function of each park is obviously influenced by the supporting elements. This paper selected four municipal cultural and creative industry parks for the investigation of their operating conditions. It is found out that the park construction performance of different construction foundation, positioning, development model is quite afferent. Therefore, it suggests that the creative industry park should be integrated with urban life, commerce, business and other functions. The park with weak ecological foundation should optimize the image of the park by means of urban renewal, and the policy should be inclined to retain talents and so on.

PV module mounting method and mounting assembly

DOEpatents

Lenox, Carl J.S.; Johnson, Kurt M.

2013-04-23

A method for mounting PV modules to a deck includes selecting PV module layout pattern so that adjacent PV module edges are spaced apart. PV mounting and support assemblies are secured to the deck according to the layout pattern using fasteners extending into the deck. The PV modules are placed on the PV mounting and support assemblies. Retaining elements are located over and secured against the upper peripheral edge surfaces of the PV modules so to secure them to the deck with the peripheral edges of the PV modules spaced apart from the deck. In some examples a PV module mounting assembly, for use on a shingled deck, comprises flashing, a base mountable on the flashing, a deck-penetrating fastener engageable with the base and securable to the deck so to secure the flashing and the base to the shingled deck, and PV module mounting hardware securable to the base.

Validation of X1 motorcycle model in industrial plant layout by using WITNESSTM simulation software

NASA Astrophysics Data System (ADS)

Hamzas, M. F. M. A.; Bareduan, S. A.; Zakaria, M. Z.; Tan, W. J.; Zairi, S.

2017-09-01

This paper demonstrates a case study on simulation, modelling and analysis for X1 Motorcycles Model. In this research, a motorcycle assembly plant has been selected as a main place of research study. Simulation techniques by using Witness software were applied to evaluate the performance of the existing manufacturing system. The main objective is to validate the data and find out the significant impact on the overall performance of the system for future improvement. The process of validation starts when the layout of the assembly line was identified. All components are evaluated to validate whether the data is significance for future improvement. Machine and labor statistics are among the parameters that were evaluated for process improvement. Average total cycle time for given workstations is used as criterion for comparison of possible variants. From the simulation process, the data used are appropriate and meet the criteria for two-sided assembly line problems.

A Computer Program for Drip Irrigation System Design for Small Plots

NASA Astrophysics Data System (ADS)

Philipova, Nina; Nicheva, Olga; Kazandjiev, Valentin; Chilikova-Lubomirova, Mila

2012-12-01

A computer programhas been developed for design of surface drip irrigation system. It could be applied for calculation of small scale fields with an area up to 10 ha. The program includes two main parts: crop water requirements and hydraulic calculations of the system. It has been developed in Graphical User Interface in MATLAB and gives opportunity for selecting some parameters from tables such as: agro- physical soil properties, characteristics of the corresponding crop, climatic data. It allows the user of the program to assume and set a definite value, for example the emitter discharge, plot parameters and etc. Eight cases of system layout according to the water source layout and the number of plots of the system operation are laid into hydraulic section of the program. It includes the design of lateral, manifold, main line and pump calculations. The program has been compiled to work in Windows.

Definition of experiments and instruments for a communication/navigation research laboratory. Volume 2: Experiment selection

NASA Technical Reports Server (NTRS)

1972-01-01

The selection and definition of candidate experiments and the associated experiment instrumentation requirements are described. Information is presented that addresses the following study objectives: (1) determine specific research and technology needs in the comm/nav field through a survey of the scientific/technical community; (2) develop manned low earth orbit space screening criteria and compile lists of potential candidate experiments; (3) in Blue Book format, define and describe selected candidate experiments in sufficient detail to develop laboratory configuration designs and layouts; and (4) develop experiment time phasing criteria and recommend a payload for sortie can/early laboratory missions.

EM calibration based on Post OPC layout analysis

NASA Astrophysics Data System (ADS)

Sreedhar, Aswin; Kundu, Sandip

2010-03-01

Design for Manufacturability (DFM) involves changes to the design and CAD tools to help increase pattern printability and improve process control. Design for Reliability (DFR) performs the same to improve reliability of devices from failures such as Electromigration (EM), gate-oxide break down, hot carrier injection (HCI), Negative Bias Temperature Insatiability (NBTI) and mechanical stress effects. Electromigration (EM) occurs due to migration or displacement of atoms as a result of the movement of electrons through a conducting medium. The rate of migration determines the Mean Time to Failure (MTTF) which is modeled as a function of temperature and current density. The model itself is calibrated through failure analysis (FA) of parts that are deemed to have failed due to EM against design parameters such as linewidth. Reliability Verification (RV) of a design involves verifying that every conducting line in a design meets certain MTTF threshold. In order to perform RV, current density for each wire must be computed. Current itself is a function of the parasitics that are determined through RC extraction. The standard practice is to perform the RC extraction and current density calculation on drawn, pre-OPC layouts. If a wire fails to meet threshold for MTTF, it may be resized. Subsequently, mask preparation steps such as OPC and PSM introduce extra features such as SRAFs, jogs,hammerheads and serifs that change their resistance, capacitance and current density values. Hence, calibrating EM model based on pre-OPC layouts will lead to different results compared to post-OPC layouts. In this work, we compare EM model calibration and reliability check based on drawn layout versus predicted layout, where the drawn layout is pre-OPC layout and predicted layout is based on litho simulation of post-OPC layout. Results show significant divergence between these two approaches, making a case for methodology based on predicted layout.

Using the clustered circular layout as an informative method for visualizing protein-protein interaction networks.

PubMed

Fung, David C Y; Wilkins, Marc R; Hart, David; Hong, Seok-Hee

2010-07-01

The force-directed layout is commonly used in computer-generated visualizations of protein-protein interaction networks. While it is good for providing a visual outline of the protein complexes and their interactions, it has two limitations when used as a visual analysis method. The first is poor reproducibility. Repeated running of the algorithm does not necessarily generate the same layout, therefore, demanding cognitive readaptation on the investigator's part. The second limitation is that it does not explicitly display complementary biological information, e.g. Gene Ontology, other than the protein names or gene symbols. Here, we present an alternative layout called the clustered circular layout. Using the human DNA replication protein-protein interaction network as a case study, we compared the two network layouts for their merits and limitations in supporting visual analysis.

Application of Approximate Pattern Matching in Two Dimensional Spaces to Grid Layout for Biochemical Network Maps

PubMed Central

Inoue, Kentaro; Shimozono, Shinichi; Yoshida, Hideaki; Kurata, Hiroyuki

2012-01-01

Background For visualizing large-scale biochemical network maps, it is important to calculate the coordinates of molecular nodes quickly and to enhance the understanding or traceability of them. The grid layout is effective in drawing compact, orderly, balanced network maps with node label spaces, but existing grid layout algorithms often require a high computational cost because they have to consider complicated positional constraints through the entire optimization process. Results We propose a hybrid grid layout algorithm that consists of a non-grid, fast layout (preprocessor) algorithm and an approximate pattern matching algorithm that distributes the resultant preprocessed nodes on square grid points. To demonstrate the feasibility of the hybrid layout algorithm, it is characterized in terms of the calculation time, numbers of edge-edge and node-edge crossings, relative edge lengths, and F-measures. The proposed algorithm achieves outstanding performances compared with other existing grid layouts. Conclusions Use of an approximate pattern matching algorithm quickly redistributes the laid-out nodes by fast, non-grid algorithms on the square grid points, while preserving the topological relationships among the nodes. The proposed algorithm is a novel use of the pattern matching, thereby providing a breakthrough for grid layout. This application program can be freely downloaded from http://www.cadlive.jp/hybridlayout/hybridlayout.html. PMID:22679486

Influence of sample pool on interference pattern in defocused interferometric particle imaging.

PubMed

Zhang, Hongxia; Zhou, Ye; Liu, Jing; Jia, Dagong; Liu, Tiegen

2017-04-01

Particles widely exist in various fields. In practical experiments, sometimes it is necessary to dissolve particles in water in a sample pool. This article proposes two typical layouts of the sample pool in defocused interferometric particle imaging (IPI). Layout I is the sample pool surface perpendicular to the incident light and layout II is the sample pool surface perpendicular to the scattered light. For layout I, the scattered light of the particles does not keep symmetric at the meridional and sagittal planes after being refracted by the sample pool surface, and elliptical interference patterns are formed at the defocused IPI image plane. But for layout II, the scattered light keeps symmetric after being refracted, and circular interference patterns are formed. Aimed at the two sample pool layouts, the ray-tracing software ZEMAX was used to simulate the spot shape of particles at different defocus distances. Furthermore, its effect on the ellipticity of the interference pattern with the tilt angle of the sample pool is analyzed. The relative error of the axis ratio for layout I does not exceed 9.2% at different defocus distances. The experimental results have good agreement with the theoretical analyses, and it indicates that layout II is more reasonable for the IPI system.

Influence of sample pool on interference pattern in defocused interferometric particle imaging

NASA Astrophysics Data System (ADS)

Zhang, Hongxia; Zhou, Ye; Liu, Jing; Jia, Dagong; Liu, Tiegen

2017-04-01

Particles widely exist in various fields. In practical experiments, sometimes it is necessary to dissolve particles in water in a sample pool. This article proposes two typical layouts of the sample pool in defocused interferometric particle imaging (IPI). Layout I is the sample pool surface perpendicular to the incident light and layout II is the sample pool surface perpendicular to the scattered light. For layout I, the scattered light of the particles does not keep symmetric at the meridional and sagittal planes after being refracted by the sample pool surface, and elliptical interference patterns are formed at the defocused IPI image plane. But for layout II, the scattered light keeps symmetric after being refracted, and circular interference patterns are formed. Aimed at the two sample pool layouts, the ray-tracing software ZEMAX was used to simulate the spot shape of particles at different defocus distances. Furthermore, its effect on the ellipticity of the interference pattern with the tilt angle of the sample pool is analyzed. The relative error of the axis ratio for layout I does not exceed 9.2% at different defocus distances. The experimental results have good agreement with the theoretical analyses, and it indicates that layout II is more reasonable for the IPI system.

Application of approximate pattern matching in two dimensional spaces to grid layout for biochemical network maps.

PubMed

Inoue, Kentaro; Shimozono, Shinichi; Yoshida, Hideaki; Kurata, Hiroyuki

2012-01-01

For visualizing large-scale biochemical network maps, it is important to calculate the coordinates of molecular nodes quickly and to enhance the understanding or traceability of them. The grid layout is effective in drawing compact, orderly, balanced network maps with node label spaces, but existing grid layout algorithms often require a high computational cost because they have to consider complicated positional constraints through the entire optimization process. We propose a hybrid grid layout algorithm that consists of a non-grid, fast layout (preprocessor) algorithm and an approximate pattern matching algorithm that distributes the resultant preprocessed nodes on square grid points. To demonstrate the feasibility of the hybrid layout algorithm, it is characterized in terms of the calculation time, numbers of edge-edge and node-edge crossings, relative edge lengths, and F-measures. The proposed algorithm achieves outstanding performances compared with other existing grid layouts. Use of an approximate pattern matching algorithm quickly redistributes the laid-out nodes by fast, non-grid algorithms on the square grid points, while preserving the topological relationships among the nodes. The proposed algorithm is a novel use of the pattern matching, thereby providing a breakthrough for grid layout. This application program can be freely downloaded from http://www.cadlive.jp/hybridlayout/hybridlayout.html.

Layouts of trigeneration plants for centralized power supply

NASA Astrophysics Data System (ADS)

Klimenko, A. V.; Agababov, V. S.; Il'ina, I. P.; Rozhnatovskii, V. D.; Burmakina, A. V.

2016-06-01

One of the possible and, under certain conditions, sufficiently effective methods for reducing consumption of fuel and energy resources is the development of plants for combined generation of different kinds of energy. In the power industry of Russia, the facilities have become widespread in which the cogeneration technology, i.e., simultaneous generation of electric energy and heat, is implemented. Such facilities can use different plants, viz., gas- and steam-turbine plants and gas-reciprocating units. Cogeneration power supply can be further developed by simultaneously supplying the users not only with electricity and heat but also with cold. Such a technology is referred to as trigeneration. To produce electricity and heat, trigeneration plants can use the same facilities that are used in cogeneration, namely, gas-turbine plants, steam-turbine plants, and gas-reciprocating units. Cold can be produced in trigeneration plants using thermotransformers of various kinds, such as vaporcompression thermotransformers, air thermotransformers, and absorption thermotransformers, that operate as chilling machines. The thermotransformers can also be used in the trigeneration plants to generate heat. The main advantage of trigeneration plants based on gas-turbine plants or gas-reciprocating units over cogeneration plants is the increased thermodynamic power supply efficiency owing to utilization of the waste-gas heat not only in winter but also in summer. In the steam-turbine-based trigeneration plants equipped with absorption thermotransformers, the enhancement of the thermodynamic power supply efficiency is determined by the increase in the heat extraction load during the nonheating season. The article presents calculated results that demonstrate higher thermodynamic efficiency of a gas-turbine-based plant with an absorption thermotransformer that operates in the trigeneration mode compared with a cogeneration gas-turbine plant. The structural arrangements of trigeneration plants designed to supply electricity, heat, and cold to the users are shown and the principles of their operation are described. The article presents results of qualitative analysis of different engineering solutions applied to select one combination of power- and heat-generating equipment and thermotransformers or another.

Novel Biocontrol Methods for Listeria monocytogenes Biofilms in Food Production Facilities.

PubMed

Gray, Jessica A; Chandry, P Scott; Kaur, Mandeep; Kocharunchitt, Chawalit; Bowman, John P; Fox, Edward M

2018-01-01

High mortality and hospitalization rates have seen Listeria monocytogenes as a foodborne pathogen of public health importance for many years and of particular concern for high-risk population groups. Food manufactures face an ongoing challenge in preventing the entry of L. monocytogenes into food production environments (FPEs) due to its ubiquitous nature. In addition to this, the capacity of L. monocytogenes strains to colonize FPEs can lead to repeated identification of L. monocytogenes in FPE surveillance. The contamination of food products requiring product recall presents large economic burden to industry and is further exacerbated by damage to the brand. Poor equipment design, facility layout, and worn or damaged equipment can result in Listeria hotspots and biofilms where traditional cleaning and disinfecting procedures may be inadequate. Novel biocontrol methods may offer FPEs effective means to help improve control of L. monocytogenes and decrease cross contamination of food. Bacteriophages have been used as a medical treatment for many years for their ability to infect and lyse specific bacteria. Endolysins, the hydrolytic enzymes of bacteriophages responsible for breaking the cell wall of Gram-positive bacteria, are being explored as a biocontrol method for food preservation and in nanotechnology and medical applications. Antibacterial proteins known as bacteriocins have been used as alternatives to antibiotics for biopreservation and food product shelf life extension. Essential oils are natural antimicrobials formed by plants and have been used as food additives and preservatives for many years and more recently as a method to prevent food spoilage by microorganisms. Competitive exclusion occurs naturally among bacteria in the environment. However, intentionally selecting and applying bacteria to effect competitive exclusion of food borne pathogens has potential as a biocontrol application. This review discusses these novel biocontrol methods and their use in food safety and prevention of spoilage, and examines their potential to control L. monocytogenes within biofilms in food production facilities.

SINQ layout, operation, applications and R&D to high power

NASA Astrophysics Data System (ADS)

Bauer, G. S.; Dai, Y.; Wagner, W.

2002-09-01

Since 1997, the Paul Scherrer Institut (PSI) is operating a 1 MW class research spallation neutron source, named SINQ. SINQ is driven by a cascade of three accelerators, the final stage being a 590 MeV isochronous ring cyclotron which delivers a beam current of 1.8 mA at an rf-frequency of 51 MHz. Since for neutron production this is essentially a dc-device, SINQ is a continuous neutron source and is optimized in its design for high time average neutron flux. This makes the facility similar to a research reactor in terms of utilization, but, in terms of beam power, it is, by a large margin, the most powerful spallation neutron source currently in operation world wide. As a consequence, target load levels prevail in SINQ which are beyond the realm of existing experience, demanding a careful approach to the design and operation of a high power target. While the best neutronic performance of the source is expected for a liquid lead-bismuth eutectic target, no experience with such systems exists. For this reason a staged approach has been embarked upon, starting with a heavy water cooled rod target of Zircaloy-2 and proceeding via steel clad lead rods towards the final goal of a target optimised in both, neutronic performance and service life time. Experience currently accruing with a test target containing sample rods with different materials specimens will help to select the proper structural material and make dependable life time estimates accounting for the real operating conditions that prevail in the facility. In parallel, both theoretical and experimental work is going on within the MEGAPIE (MEGAwatt Pilot Experiment) project, a joint initiative by six European research institutions and JAERI (Japan), DOE (USA) and KAERI (Korea), to design, build, operate and explore a liquid lead-bismuth spallation target for 1MW of beam power, taking advantage of the existing spallation neutron facility SINQ.

Novel Biocontrol Methods for Listeria monocytogenes Biofilms in Food Production Facilities

PubMed Central

Gray, Jessica A.; Chandry, P. Scott; Kaur, Mandeep; Kocharunchitt, Chawalit; Bowman, John P.; Fox, Edward M.

2018-01-01

High mortality and hospitalization rates have seen Listeria monocytogenes as a foodborne pathogen of public health importance for many years and of particular concern for high-risk population groups. Food manufactures face an ongoing challenge in preventing the entry of L. monocytogenes into food production environments (FPEs) due to its ubiquitous nature. In addition to this, the capacity of L. monocytogenes strains to colonize FPEs can lead to repeated identification of L. monocytogenes in FPE surveillance. The contamination of food products requiring product recall presents large economic burden to industry and is further exacerbated by damage to the brand. Poor equipment design, facility layout, and worn or damaged equipment can result in Listeria hotspots and biofilms where traditional cleaning and disinfecting procedures may be inadequate. Novel biocontrol methods may offer FPEs effective means to help improve control of L. monocytogenes and decrease cross contamination of food. Bacteriophages have been used as a medical treatment for many years for their ability to infect and lyse specific bacteria. Endolysins, the hydrolytic enzymes of bacteriophages responsible for breaking the cell wall of Gram-positive bacteria, are being explored as a biocontrol method for food preservation and in nanotechnology and medical applications. Antibacterial proteins known as bacteriocins have been used as alternatives to antibiotics for biopreservation and food product shelf life extension. Essential oils are natural antimicrobials formed by plants and have been used as food additives and preservatives for many years and more recently as a method to prevent food spoilage by microorganisms. Competitive exclusion occurs naturally among bacteria in the environment. However, intentionally selecting and applying bacteria to effect competitive exclusion of food borne pathogens has potential as a biocontrol application. This review discusses these novel biocontrol methods and their use in food safety and prevention of spoilage, and examines their potential to control L. monocytogenes within biofilms in food production facilities. PMID:29666613

Study of LED layout in indoor visible light communication and performance analysis

NASA Astrophysics Data System (ADS)

Wang, Jiaan; Che, Ying; Wang, Xinlan; Guo, Linyang; Li, Jing

2017-10-01

Light emitting diodes(LED) could provide both illumination and data communication in indoor visible light communication(VLC) that owns the modulation bandwith from several from several MHz to seneral hundreds of MHz. The layout of LED plays an important role in maintaining a steady optical power distribution over the receiving plane. The existing rectangular LED layout does not provide a full coverage on the receiving plane leaving receiving optical power outage area, which in turn affects the best performance of the VLC system. This paper design a circular layout scheme of LED in 5mX5mX3m room based on the criterion of the illumination minimum mean square deviation. The influence of the distribution of the intensity of illumination with the radius of 1m and 1.5m,for including the wall reflection and not including the wall reflection, and make a comparison with rectangular LED layout of illumination distribution, when the number of LEDs with rectangular layout as same as circular layout. Including the number of LEDs are 4 and 16.For a specific simulation parameters as following:height of receiving plane is 0.85m,a single LEDs is composed of 60X60 LED chips, the parameters of a single chip is that transmitting power is 20mW,center luminous intensity is 0.73cd.semiangle at half power is 70deg.The parameters of concentrator is that photodiode area is 1cm2,photodiode responsivity is 0.4,field of view at the receiver is 85deg.Other parameters are that reflective index of concentrator is 1.5,reflectivity of wall is 0.8.Circular layout and rectangular layout are analyzed through simulation of the received optical power distribution, signal noise ratio distribution in non line of sight(including the wall reflection) and line of sight(not including the wall reflection),when the number of the LED is different. It is clear from the results that the received optical power distribution of non line of sight is better than line of sight, when the number of the LED are same, but the signal noise ratio distribution is decreased result of the reflection of the wall. It is found that the received optical power of circular layout is better than the received optical power distribution of rectangulr layout, and circular layout is a good solution that add the received optical power at the 4 corners of room, improve the system ability of communication, when making a contrast of rectangular lyout with circular layout,at the same time,the fluctuate of circular layout's signal to noise ratio of is smller than rectangular layuot.The radius of circular layout or the location of rectangular layout is keeping, the received optical power of receiving plane is increased, by adding the number of LED,in the meantime, the interference between LED light source also increase. But the increase of the circular layout radius when the number of LED remain the same is helpful to reduce the inter symbol interference that work out between LED each other, enhance the system signal noise ratio. In this paper, the results of the reaearch provides a new idea for indoor visible light communication with non-standard room (Size of room is not 5mX5mX3m), at the same time, provides guiding significance for future setting up the indoor visible light communication links.

Computer-aided engineering system for design of sequence arrays and lithographic masks

DOEpatents

Hubbell, Earl A.; Lipshutz, Robert J.; Morris, Macdonald S.; Winkler, James L.

1997-01-01

An improved set of computer tools for forming arrays. According to one aspect of the invention, a computer system is used to select probes and design the layout of an array of DNA or other polymers with certain beneficial characteristics. According to another aspect of the invention, a computer system uses chip design files to design and/or generate lithographic masks.

An EAS experiment at mountain altitude for the detection of gamma-ray sources

NASA Technical Reports Server (NTRS)

Allkofer, O. C.; Samorski, M.; Stamm, W.

1985-01-01

The plan of an extensive air shower experiment 2.200 m above sea level for the detection of 10 to the 14th power eV to 10 to the 17th power eV gamma rays from sources in the declination band 0 deg to + 60 deg is described. The site selection, detector array and electronic layout are detailed.

The Effect of Design Modifications to the Typographical Layout of the New York State Elementary Science Learning Standards on User Preference and Process Time

ERIC Educational Resources Information Center

Arnold, Jeffery E.

2010-01-01

The purpose of this study was to determine the effect of four different design layouts of the New York State elementary science learning standards on user processing time and preference. Three newly developed layouts contained the same information as the standards core curriculum. In this study, the layout of the core guide is referred to as Book.…

Numerical investigation of optimal layout of rockbolts for ground structures

NASA Astrophysics Data System (ADS)

Kato, Junji; Ishi, Keiichiro; Terada, Kenjiro; Kyoya, Takashi

Due to difficulty to obtain reliable ground data, layout of rockbolts is determined entirely in a classical way assuming an isotropic rock stress condition. The present study assumes anisotropic stress condition and optimizes layout of rockbolts in order to maximize the stiffness of unstable ground of tunnels and slopes by applying multiphase layout optimization. It was verified that this method has a certain possibility to improve the stiffness of unstable ground.

The Effect of Visual Task Difficulty on the Fixation-Related Lambda Response

DTIC Science & Technology

2018-02-01

than limiting eye movements in experimental paradigms. The lambda response, a prominent neural signature of the fixation-related potential, has been...release; distribution is unlimited. v List of Figures Fig. 1 Task layout. The left image shows the layout of the experimental environment while a...on an invisible 7 × 7 grid. Fig. 1 Task layout. The left image shows the layout of the experimental environment while a participant performs the

Design space exploration for early identification of yield limiting patterns

NASA Astrophysics Data System (ADS)

Li, Helen; Zou, Elain; Lee, Robben; Hong, Sid; Liu, Square; Wang, JinYan; Du, Chunshan; Zhang, Recco; Madkour, Kareem; Ali, Hussein; Hsu, Danny; Kabeel, Aliaa; ElManhawy, Wael; Kwan, Joe

2016-03-01

In order to resolve the causality dilemma of which comes first, accurate design rules or real designs, this paper presents a flow for exploration of the layout design space to early identify problematic patterns that will negatively affect the yield. A new random layout generating method called Layout Schema Generator (LSG) is reported in this paper, this method generates realistic design-like layouts without any design rule violation. Lithography simulation is then used on the generated layout to discover the potentially problematic patterns (hotspots). These hotspot patterns are further explored by randomly inducing feature and context variations to these identified hotspots through a flow called Hotspot variation Flow (HSV). Simulation is then performed on these expanded set of layout clips to further identify more problematic patterns. These patterns are then classified into design forbidden patterns that should be included in the design rule checker and legal patterns that need better handling in the RET recipes and processes.

Topology-optimized metasurfaces: impact of initial geometric layout.

PubMed

Yang, Jianji; Fan, Jonathan A

2017-08-15

Topology optimization is a powerful iterative inverse design technique in metasurface engineering and can transform an initial layout into a high-performance device. With this method, devices are optimized within a local design phase space, making the identification of suitable initial geometries essential. In this Letter, we examine the impact of initial geometric layout on the performance of large-angle (75 deg) topology-optimized metagrating deflectors. We find that when conventional metasurface designs based on dielectric nanoposts are used as initial layouts for topology optimization, the final devices have efficiencies around 65%. In contrast, when random initial layouts are used, the final devices have ultra-high efficiencies that can reach 94%. Our numerical experiments suggest that device topologies based on conventional metasurface designs may not be suitable to produce ultra-high-efficiency, large-angle metasurfaces. Rather, initial geometric layouts with non-trivial topologies and shapes are required.

Describing litho-constrained layout by a high-resolution model filter

NASA Astrophysics Data System (ADS)

Tsai, Min-Chun

2008-05-01

A novel high-resolution model (HRM) filtering technique was proposed to describe litho-constrained layouts. Litho-constrained layouts are layouts that have difficulties to pattern or are highly sensitive to process-fluctuations under current lithography technologies. HRM applies a short-wavelength (or high NA) model simulation directly on the pre-OPC, original design layout to filter out low spatial-frequency regions, and retain high spatial-frequency components which are litho-constrained. Since no OPC neither mask-synthesis steps are involved, this new technique is highly efficient in run time and can be used in design stage to detect and fix litho-constrained patterns. This method has successfully captured all the hot-spots with less than 15% overshoots on a realistic 80 mm2 full-chip M1 layout in 65nm technology node. A step by step derivation of this HRM technique is presented in this paper.

Localized direction selective responses in the dendrites of visual interneurons of the fly

PubMed Central

2010-01-01

Background The various tasks of visual systems, including course control, collision avoidance and the detection of small objects, require at the neuronal level the dendritic integration and subsequent processing of many spatially distributed visual motion inputs. While much is known about the pooled output in these systems, as in the medial superior temporal cortex of monkeys or in the lobula plate of the insect visual system, the motion tuning of the elements that provide the input has yet received little attention. In order to visualize the motion tuning of these inputs we examined the dendritic activation patterns of neurons that are selective for the characteristic patterns of wide-field motion, the lobula-plate tangential cells (LPTCs) of the blowfly. These neurons are known to sample direction-selective motion information from large parts of the visual field and combine these signals into axonal and dendro-dendritic outputs. Results Fluorescence imaging of intracellular calcium concentration allowed us to take a direct look at the local dendritic activity and the resulting local preferred directions in LPTC dendrites during activation by wide-field motion in different directions. These 'calcium response fields' resembled a retinotopic dendritic map of local preferred directions in the receptive field, the layout of which is a distinguishing feature of different LPTCs. Conclusions Our study reveals how neurons acquire selectivity for distinct visual motion patterns by dendritic integration of the local inputs with different preferred directions. With their spatial layout of directional responses, the dendrites of the LPTCs we investigated thus served as matched filters for wide-field motion patterns. PMID:20384983

Patient handling system for carbon ion beam scanning therapy

PubMed Central

Shirai, Toshiyuki; Takei, Yuka; Furukawa, Takuji; Inaniwa, Taku; Matsuzaki, Yuka; Kumagai, Motoki; Murakami, Takeshi; Noda, Koji

2012-01-01

Our institution established a new treatment facility for carbon ion beam scanning therapy in 2010. The major advantages of scanning beam treatment compared to the passive beam treatment are the following: high dose conformation with less excessive dose to the normal tissues, no bolus compensator and patient collimator/ multi‐leaf collimator, better dose efficiency by reducing the number of scatters. The new facility was designed to solve several problems encountered in the existing facility, at which several thousand patients were treated over more than 15 years. Here, we introduce the patient handling system in the new treatment facility. The new facility incorporates three main systems, a scanning irradiation system (S‐IR), treatment planning system (TPS), and patient handling system (PTH). The PTH covers a wide range of functions including imaging, geometrical/position accuracy including motion management (immobilization, robotic arm treatment bed), layout of the treatment room, treatment workflow, software, and others. The first clinical trials without respiratory gating have been successfully started. The PTH allows a reduction in patient stay in the treatment room to as few as 7 min. The PTH plays an important role in carbon ion beam scanning therapy at the new institution, particularly in the management of patient handling, application of image‐guided therapy, and improvement of treatment workflow, and thereby allows substantially better treatment at minimum cost. PACS numbers: 87.56.‐v; 87.57.‐s; 87.55.‐x PMID:23149784

An efficient biological pathway layout algorithm combining grid-layout and spring embedder for complicated cellular location information

PubMed Central

2010-01-01

Background Graph drawing is one of the important techniques for understanding biological regulations in a cell or among cells at the pathway level. Among many available layout algorithms, the spring embedder algorithm is widely used not only for pathway drawing but also for circuit placement and www visualization and so on because of the harmonized appearance of its results. For pathway drawing, location information is essential for its comprehension. However, complex shapes need to be taken into account when torus-shaped location information such as nuclear inner membrane, nuclear outer membrane, and plasma membrane is considered. Unfortunately, the spring embedder algorithm cannot easily handle such information. In addition, crossings between edges and nodes are usually not considered explicitly. Results We proposed a new grid-layout algorithm based on the spring embedder algorithm that can handle location information and provide layouts with harmonized appearance. In grid-layout algorithms, the mapping of nodes to grid points that minimizes a cost function is searched. By imposing positional constraints on grid points, location information including complex shapes can be easily considered. Our layout algorithm includes the spring embedder cost as a component of the cost function. We further extend the layout algorithm to enable dynamic update of the positions and sizes of compartments at each step. Conclusions The new spring embedder-based grid-layout algorithm and a spring embedder algorithm are applied to three biological pathways; endothelial cell model, Fas-induced apoptosis model, and C. elegans cell fate simulation model. From the positional constraints, all the results of our algorithm satisfy location information, and hence, more comprehensible layouts are obtained as compared to the spring embedder algorithm. From the comparison of the number of crossings, the results of the grid-layout-based algorithm tend to contain more crossings than those of the spring embedder algorithm due to the positional constraints. For a fair comparison, we also apply our proposed method without positional constraints. This comparison shows that these results contain less crossings than those of the spring embedder algorithm. We also compared layouts of the proposed algorithm with and without compartment update and verified that latter can reach better local optima. PMID:20565884

[Evolution of work duties in manufacturing activities].

PubMed

Guerra, F

2001-01-01

The present work deals with duties' evolution according to the aspect of the investment's increase in facilities and equipment for employ, of industry-wide agreement, of cost accounting, of added value, of plant lay-out, of job competence and of production technologies. The mutual relation between duties and risk of cumulative trauma disorders is studied in qualitative and quantitative way making use of active and waiting labour time allotment during the labour cycle, rest and fatigue factor, labour losses, collective and individual breaks, high repeated work and worked items' variability. In conclusion the paper presents elements and examples about investments in automation and organisation with relay-out.

GRAPHICS MANAGER (GFXMGR): An interactive graphics software program for the Advanced Electronics Design (AED) graphics controller, Model 767

DOE Office of Scientific and Technical Information (OSTI.GOV)

Faculjak, D.A.

1988-03-01

Graphics Manager (GFXMGR) is menu-driven, user-friendly software designed to interactively create, edit, and delete graphics displays on the Advanced Electronics Design (AED) graphics controller, Model 767. The software runs on the VAX family of computers and has been used successfully in security applications to create and change site layouts (maps) of specific facilities. GFXMGR greatly benefits graphics development by minimizing display-development time, reducing tedium on the part of the user, and improving system performance. It is anticipated that GFXMGR can be used to create graphics displays for many types of applications. 8 figs., 2 tabs.

STS-114 Discovery Return to Flight: International Space Station Processing Overview

NASA Technical Reports Server (NTRS)

2005-01-01

Bruce Buckingham, NASA Public Affairs, introduces Scott Higgenbotham, STS-114 Payload Manager. Higgenbotham gives a power point presentation on the hardware that is going to fly in the Discovery Mission to the International Space Station. He presents a layout of the hardware which includes The Logistics Flight 1 (LF1) launch package configuration Multipurpose Logistics Module (MPLM), External Stowage Platform-2 (ESP-2) and the Lightweight Mission Peculiar Equipment Support Structure Carrier (LMC). He explains these payloads in detail. The LF-1 team is also shown in the International Space Station Processing Facility. This presentation ends with a brief question and answer period.

BioLayout(Java): versatile network visualisation of structural and functional relationships.

PubMed

Goldovsky, Leon; Cases, Ildefonso; Enright, Anton J; Ouzounis, Christos A

2005-01-01

Visualisation of biological networks is becoming a common task for the analysis of high-throughput data. These networks correspond to a wide variety of biological relationships, such as sequence similarity, metabolic pathways, gene regulatory cascades and protein interactions. We present a general approach for the representation and analysis of networks of variable type, size and complexity. The application is based on the original BioLayout program (C-language implementation of the Fruchterman-Rheingold layout algorithm), entirely re-written in Java to guarantee portability across platforms. BioLayout(Java) provides broader functionality, various analysis techniques, extensions for better visualisation and a new user interface. Examples of analysis of biological networks using BioLayout(Java) are presented.

Automated aerial image based CD metrology initiated by pattern marking with photomask layout data

NASA Astrophysics Data System (ADS)

Davis, Grant; Choi, Sun Young; Jung, Eui Hee; Seyfarth, Arne; van Doornmalen, Hans; Poortinga, Eric

2007-05-01

The photomask is a critical element in the lithographic image transfer process from the drawn layout to the final structures on the wafer. The non-linearity of the imaging process and the related MEEF impose a tight control requirement on the photomask critical dimensions. Critical dimensions can be measured in aerial images with hardware emulation. This is a more recent complement to the standard scanning electron microscope measurement of wafers and photomasks. Aerial image measurement includes non-linear, 3-dimensional, and materials effects on imaging that cannot be observed directly by SEM measurement of the mask. Aerial image measurement excludes the processing effects of printing and etching on the wafer. This presents a unique contribution to the difficult process control and modeling tasks in mask making. In the past, aerial image measurements have been used mainly to characterize the printability of mask repair sites. Development of photomask CD characterization with the AIMS TM tool was motivated by the benefit of MEEF sensitivity and the shorter feedback loop compared to wafer exposures. This paper describes a new application that includes: an improved interface for the selection of meaningful locations using the photomask and design layout data with the Calibre TM Metrology Interface, an automated recipe generation process, an automated measurement process, and automated analysis and result reporting on a Carl Zeiss AIMS TM system.

SimArray: a user-friendly and user-configurable microarray design tool

PubMed Central

Auburn, Richard P; Russell, Roslin R; Fischer, Bettina; Meadows, Lisa A; Sevillano Matilla, Santiago; Russell, Steven

2006-01-01

Background Microarrays were first developed to assess gene expression but are now also used to map protein-binding sites and to assess allelic variation between individuals. Regardless of the intended application, efficient production and appropriate array design are key determinants of experimental success. Inefficient production can make larger-scale studies prohibitively expensive, whereas poor array design makes normalisation and data analysis problematic. Results We have developed a user-friendly tool, SimArray, which generates a randomised spot layout, computes a maximum meta-grid area, and estimates the print time, in response to user-specified design decisions. Selected parameters include: the number of probes to be printed; the microtitre plate format; the printing pin configuration, and the achievable spot density. SimArray is compatible with all current robotic spotters that employ 96-, 384- or 1536-well microtitre plates, and can be configured to reflect most production environments. Print time and maximum meta-grid area estimates facilitate evaluation of each array design for its suitability. Randomisation of the spot layout facilitates correction of systematic biases by normalisation. Conclusion SimArray is intended to help both established researchers and those new to the microarray field to develop microarray designs with randomised spot layouts that are compatible with their specific production environment. SimArray is an open-source program and is available from . PMID:16509966

The ISS Fluids and Combustion Facility: Experiment Accommodations Summary

NASA Technical Reports Server (NTRS)

Corban, Robert R.; Simons, Stephen N. (Technical Monitor)

2001-01-01

The International Space Station's (ISS's) Fluids and Combustion Facility (FCF) is in the process of final design and development activities to accommodate a wide range of experiments in the fields of combustion science and fluid physics. The FCF is being designed to provide potential experiments with well defined interfaces that can meet the experimenters requirements, provide the flexibility for on-orbit reconfiguration, and provide the maximum capability within the ISS resources and constraints. As a multi-disciplined facility, the FCF supports various experiments and scientific objectives, which will be developed in the future and are not completely defined at this time. Since developing experiments to be performed within FCF is a continuous process throughout the FCF's operational lifetime, each individual experiment must determine the best configuration of utilizing facility capabilities and resources with augmentation of specific experiment hardware. Configurations of potential experiments in the FCF has been on-going to better define the FCF interfaces and provide assurances that the FCF design will meet its design requirements. This paper provides a summary of ISS resources and FCF capabilities, which are available for potential ISS FCF users. Also, to better understand the utilization of the FCF a description of a various experiment layouts and associated operations in the FCF are provided.

Two decades (1993-2012) of adult intensive care unit design: a comparative study of the physical design features of the best practice examples.

PubMed

Rashid, Mahbub

2014-01-01

In 2006, Critical Care Nursing Quarterly published a study of the physical design features of a set of best practice example adult intensive care units (ICUs). These adult ICUs were awarded between 1993 and 2003 by the Society of Critical Care Medicine (SCCM), the American Association of Critical-Care Nurses, and the American Institute of Architects/Academy of Architecture for Health for their efforts to promote the critical care unit environment through design. Since 2003, several more adult ICUs were awarded by the same organizations for similar efforts. This study includes these newer ICUs along with those of the previous study to cover a period of 2 decades from 1993 to 2012. Like the 2006 study, this study conducts a systematic content analysis of the materials submitted by the award-winning adult ICUs. On the basis of the analysis, the study compares the 1993-2002 and 2003-2012 adult ICUs in relation to construction type, unit specialty, unit layout, unit size, patient room size and design, support and service area layout, and family space design. The study also compares its findings with the 2010 Guidelines for Design and Construction of Health Care Facilities of the Facility Guidelines Institute and the 2012 Guidelines for Intensive Care Unit Design of the SCCM. The study indicates that the award-winning ICUs of both decades used several design features that were associated with positive outcomes in research studies. The study also indicates that the award-winning ICUs of the second decade used more evidence-based design features than those of the first decades. In most cases, these ICUs exceeded the requirements of the Facility Guidelines Institute Guidelines to meet those of the SCCM Guidelines. Yet, the award-winning ICUs of both decades also used several features that had very little or no supporting research evidence. Since they all were able to create an optimal critical care environment for which they were awarded, having knowledge of the physical design of these award-winning ICUs may help design better ICUs.

Loss analysis and optimum design of a highly efficient and compact CMOS DC–DC converter with novel transistor layout using 60 nm multipillar-type vertical body channel MOSFET

NASA Astrophysics Data System (ADS)

Itoh, Kazuki; Endoh, Tetsuo

2018-04-01

In this paper, we present a novel transistor layout of multi pillar-type vertical body-channel (BC) MOSFET for cascode power switches for improving the efficiency and compactness of CMOS DC–DC converters. The proposed layout features a stacked and multifingered layout to suppress the loss due to parasitic components such as diffusion resistance and contact resistance. In addition, the loss of each MOSFET, which configures cascode power switches, is analyzed, and it is revealed that the total optimum gate width and loss with the high-side (HS) n-type MOSFET topology are 27 and 16% smaller than those with the HS p-type MOSFET topology, respectively. Moreover, a circuit simulation of 2.0 to 0.8 V, 100 MHz CMOS DC–DC converters with the proposed layout is carried out by using experimentally extracted models of BSIM4 60 nm vertical BC MOSFETs. The peak efficiency of the HS n-type MOSFET converter with the proposed layout is 90.1%, which is 6.0% higher than that with the conventional layout.

Learning Building Layouts with Non-geometric Visual Information: The Effects of Visual Impairment and Age

PubMed Central

Kalia, Amy A.; Legge, Gordon E.; Giudice, Nicholas A.

2009-01-01

Previous studies suggest that humans rely on geometric visual information (hallway structure) rather than non-geometric visual information (e.g., doors, signs and lighting) for acquiring cognitive maps of novel indoor layouts. This study asked whether visual impairment and age affect reliance on non-geometric visual information for layout learning. We tested three groups of participants—younger (< 50 years) normally sighted, older (50–70 years) normally sighted, and low vision (people with heterogeneous forms of visual impairment ranging in age from 18–67). Participants learned target locations in building layouts using four presentation modes: a desktop virtual environment (VE) displaying only geometric cues (Sparse VE), a VE displaying both geometric and non-geometric cues (Photorealistic VE), a Map, and a Real building. Layout knowledge was assessed by map drawing and by asking participants to walk to specified targets in the real space. Results indicate that low-vision and older normally-sighted participants relied on additional non-geometric information to accurately learn layouts. In conclusion, visual impairment and age may result in reduced perceptual and/or memory processing that makes it difficult to learn layouts without non-geometric visual information. PMID:19189732

Generating Multi-Destination Maps.

PubMed

Zhang, Junsong; Fan, Jiepeng; Luo, Zhenshan

2017-08-01

Multi-destination maps are a kind of navigation maps aimed to guide visitors to multiple destinations within a region, which can be of great help to urban visitors. However, they have not been developed in the current online map service. To address this issue, we introduce a novel layout model designed especially for generating multi-destination maps, which considers the global and local layout of a multi-destination map. We model the layout problem as a graph drawing that satisfies a set of hard and soft constraints. In the global layout phase, we balance the scale factor between ROIs. In the local layout phase, we make all edges have good visibility and optimize the map layout to preserve the relative length and angle of roads. We also propose a perturbation-based optimization method to find an optimal layout in the complex solution space. The multi-destination maps generated by our system are potential feasible on the modern mobile devices and our result can show an overview and a detail view of the whole map at the same time. In addition, we perform a user study to evaluate the effectiveness of our method, and the results prove that the multi-destination maps achieve our goals well.

Layout and cabling considerations for a large communications antenna array

NASA Technical Reports Server (NTRS)

Logan, R. T., Jr.

1993-01-01

Layout considerations for a large deep space communications antenna array are discussed. A fractal geometry for the antenna layout is described that provides optimal packing of antenna elements, efficient cable routing, and logical division of the array into identical sub-arrays.

SOI layout decomposition for double patterning lithography on high-performance computer platforms

NASA Astrophysics Data System (ADS)

Verstov, Vladimir; Zinchenko, Lyudmila; Makarchuk, Vladimir

2014-12-01

In the paper silicon on insulator layout decomposition algorithms for the double patterning lithography on high performance computing platforms are discussed. Our approach is based on the use of a contradiction graph and a modified concurrent breadth-first search algorithm. We evaluate our technique on 45 nm Nangate Open Cell Library including non-Manhattan geometry. Experimental results show that our soft computing algorithms decompose layout successfully and a minimal distance between polygons in layout is increased.

Library API for Z-Order Memory Layout

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bethel, E. Wes

This library provides a simple-to-use API for implementing an altnerative to traditional row-major order in-memory layout, one based on a Morton- order space filling curve (SFC) , specifically, a Z-order variant of the Morton order curve. The library enables programmers to, after a simple initialization step, to convert a multidimensional array from row-major to Z- order layouts, then use a single, generic API call to access data from any arbitrary (i,j,k) location from within the array, whether it it be stored in row- major or z-order format. The motivation for using a SFC in-memory layout is for improved spatial locality,more » which results in increased use of local high speed cache memory. The basic idea is that with row-major order layouts, a data access to some location that is nearby in index space is likely far away in physical memory, resulting in poor spatial locality and slow runtime. On the other hand, with a SFC-based layout, accesses that are nearby in index space are much more likely to also be nearby in physical memory, resulting in much better spatial locality, and better runtime performance. Numerous studies over the years have shown significant runtime performance gains are realized by using a SFC-based memory layout compared to a row-major layout, sometimes by as much as 50%, which result from the better use of the memory and cache hierarchy that are attendant with a SFC-based layout (see, for example, [Beth2012]). This library implementation is intended for use with codes that work with structured, array-based data in 2 or 3 dimensions. It is not appropriate for use with unstructured or point-based data.« less

Discrete wavelength selection for the optical readout of a metamaterial biosensing system for glucose concentration estimation via a support vector regression model.

PubMed

Teutsch, T; Mesch, M; Giessen, H; Tarin, C

2015-01-01

In this contribution, a method to select discrete wavelengths that allow an accurate estimation of the glucose concentration in a biosensing system based on metamaterials is presented. The sensing concept is adapted to the particular application of ophthalmic glucose sensing by covering the metamaterial with a glucose-sensitive hydrogel and the sensor readout is performed optically. Due to the fact that in a mobile context a spectrometer is not suitable, few discrete wavelengths must be selected to estimate the glucose concentration. The developed selection methods are based on nonlinear support vector regression (SVR) models. Two selection methods are compared and it is shown that wavelengths selected by a sequential forward feature selection algorithm achieves an estimation improvement. The presented method can be easily applied to different metamaterial layouts and hydrogel configurations.

Learning Layouts for Single-Page Graphic Designs.

PubMed

O'Donovan, Peter; Agarwala, Aseem; Hertzmann, Aaron

2014-08-01

This paper presents an approach for automatically creating graphic design layouts using a new energy-based model derived from design principles. The model includes several new algorithms for analyzing graphic designs, including the prediction of perceived importance, alignment detection, and hierarchical segmentation. Given the model, we use optimization to synthesize new layouts for a variety of single-page graphic designs. Model parameters are learned with Nonlinear Inverse Optimization (NIO) from a small number of example layouts. To demonstrate our approach, we show results for applications including generating design layouts in various styles, retargeting designs to new sizes, and improving existing designs. We also compare our automatic results with designs created using crowdsourcing and show that our approach performs slightly better than novice designers.

Design of in-flight fragment separator using high-power primary beams in the energy of a few hundred MeV/u

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kim, J. Y.; Kim, J. W.; Wan, W.

2015-07-15

An in-flight fragment separator usually requires large acceptance and high momentum resolution to minimize the loss of a rare isotope beam of interest produced at a thin target, which is especially important when {sup 238}U fission reactions in the energy of 200 MeV/u are used. The production target and beam dump are located in the pre-separator, where a beam power of up to 400 kW is dissipated. The area is surrounded by thick radiation shielding walls, which result in long drift spaces between adjacent magnetic components at various locations and an asymmetrical layout. Efforts have been made to minimize non-linearmore » effects in the pre-separator beam optics with trials of different separator configurations and correction schemes using COSY Infinity and GICOSY. The main separator is configured to be mirror symmetric such that correction with hexapole and octupole coils can be more readily applied. The separator configuration was finalized to allow the facility design to proceed and the key components including superconducting magnets have been designed and prototyped. In addition, the separator design has been evaluated using LISE++ including a set of wedge degraders at dispersive focal planes to improve the yield and purity of selected isotope beam.« less

Acta Aerodynanica Sinica (Selected Articles),

DTIC Science & Technology

1985-12-05

to the director of the institute and his advisor Professor R. Eppler for their assistance. A %: 61 References [1] Ji Xiumei, "Aerodynamic Layout of... Airfoils ; by Wang Jie ..........o......................114 ~-A Simpler Implicit Method to Solve N-S Equation; 1 Zhang Hanxin, Yu Zechu, Lu Linsheng...In addition, we also discovered that the leading edge separation vortex-could improve the lift of the airfoil . Hence, the important task is to

Cost Effectiveness Study of Wastewater Management Systems for Selected U.S. Coast Guard Vessels. Volume 2. Effectiveness Assessment of Candidate Systems

DTIC Science & Technology

1977-03-01

267 Input Layout for Each Card Type ...................... 269 Input Sequence .......................... 271 SAMPLE PROBLEM...13 3 Sample Data rormn Used for Documenting MSD Effectiveness Attribute Data ........................... 15 -1 Sample Form Used for Documenting WMS...from commodes, urinals and garbage grinder) and gray (galley and turbid, i.e., output from sinks, showers, laundry, deck, drains, etc.) wastewaters

Computer-aided engineering system for design of sequence arrays and lithographic masks

DOEpatents

Hubbell, Earl A.; Morris, MacDonald S.; Winkler, James L.

1999-01-05

An improved set of computer tools for forming arrays. According to one aspect of the invention, a computer system (100) is used to select probes and design the layout of an array of DNA or other polymers with certain beneficial characteristics. According to another aspect of the invention, a computer system uses chip design files (104) to design and/or generate lithographic masks (110).

Computer-aided engineering system for design of sequence arrays and lithographic masks

DOEpatents

Hubbell, Earl A.; Morris, MacDonald S.; Winkler, James L.

1996-01-01

An improved set of computer tools for forming arrays. According to one aspect of the invention, a computer system (100) is used to select probes and design the layout of an array of DNA or other polymers with certain beneficial characteristics. According to another aspect of the invention, a computer system uses chip design files (104) to design and/or generate lithographic masks (110).

Computer-aided engineering system for design of sequence arrays and lithographic masks

DOEpatents

Hubbell, E.A.; Morris, M.S.; Winkler, J.L.

1999-01-05

An improved set of computer tools for forming arrays is disclosed. According to one aspect of the invention, a computer system is used to select probes and design the layout of an array of DNA or other polymers with certain beneficial characteristics. According to another aspect of the invention, a computer system uses chip design files to design and/or generate lithographic masks. 14 figs.

Computer-aided engineering system for design of sequence arrays and lithographic masks

DOEpatents

Hubbell, E.A.; Lipshutz, R.J.; Morris, M.S.; Winkler, J.L.

1997-01-14

An improved set of computer tools for forming arrays is disclosed. According to one aspect of the invention, a computer system is used to select probes and design the layout of an array of DNA or other polymers with certain beneficial characteristics. According to another aspect of the invention, a computer system uses chip design files to design and/or generate lithographic masks. 14 figs.

Computer-aided engineering system for design of sequence arrays and lithographic masks

DOEpatents

Hubbell, E.A.; Morris, M.S.; Winkler, J.L.

1996-11-05

An improved set of computer tools for forming arrays is disclosed. According to one aspect of the invention, a computer system is used to select probes and design the layout of an array of DNA or other polymers with certain beneficial characteristics. According to another aspect of the invention, a computer system uses chip design files to design and/or generate lithographic masks. 14 figs.

The ATLAS Liquid Argon Electromagnetic Calorimeter

NASA Astrophysics Data System (ADS)

Carminati, L.

2005-10-01

The construction of the ATLAS Liquid Argon Electromagnetic calorimeter has been completed and commissioning is in progress. After a brief description of the detector layout, readout electronics and calibration, a review of the present status of the integration and the detector qualification is reported. Finally a selection of performance results obtained during several test beams will be presented with particular attention to linearity, uniformity, position reconstruction and γ/π0 separation.

Object-based implicit learning in visual search: perceptual segmentation constrains contextual cueing.

PubMed

Conci, Markus; Müller, Hermann J; von Mühlenen, Adrian

2013-07-09

In visual search, detection of a target is faster when it is presented within a spatial layout of repeatedly encountered nontarget items, indicating that contextual invariances can guide selective attention (contextual cueing; Chun & Jiang, 1998). However, perceptual regularities may interfere with contextual learning; for instance, no contextual facilitation occurs when four nontargets form a square-shaped grouping, even though the square location predicts the target location (Conci & von Mühlenen, 2009). Here, we further investigated potential causes for this interference-effect: We show that contextual cueing can reliably occur for targets located within the region of a segmented object, but not for targets presented outside of the object's boundaries. Four experiments demonstrate an object-based facilitation in contextual cueing, with a modulation of context-based learning by relatively subtle grouping cues including closure, symmetry, and spatial regularity. Moreover, the lack of contextual cueing for targets located outside the segmented region was due to an absence of (latent) learning of contextual layouts, rather than due to an attentional bias towards the grouped region. Taken together, these results indicate that perceptual segmentation provides a basic structure within which contextual scene regularities are acquired. This in turn argues that contextual learning is constrained by object-based selection.

Preliminary design of a supersonic Short Takeoff and Vertical Landing (STOVL) fighter aircraft

NASA Technical Reports Server (NTRS)

Cox, Brian; Borchers, Paul; Gomer, Charlie; Henderson, Dean; Jacobs, Tavis; Lawson, Todd; Peterson, Eric; Ross, Tweed, III; Bellmard, Larry

1990-01-01

The preliminary design study of a supersonic Short Takeoff and Vertical Landing (STOVL) fighter is presented. A brief historical survey of powered lift vehicles was presented, followed by a technology assessment of the latest supersonic STOVL engine cycles under consideration by industry and government in the U.S. and UK. A survey of operational fighter/attack aircraft and the modern battlefield scenario were completed to develop, respectively, the performance requirements and mission profiles for the study. Three configurations were initially investigated with the following engine cycles: a hybrid fan vectored thrust cycle, a lift+lift/cruise cycle, and a mixed flow vectored thrust cycle. The lift+lift/cruise aircraft configuration was selected for detailed design work which consisted of: (1) a material selection and structural layout, including engine removal considerations, (2) an aircraft systems layout, (3) a weapons integration model showing the internal weapons bay mechanism, (4) inlet and nozzle integration, (5) an aircraft suckdown prediction, (6) an aircraft stability and control analysis, including a takeoff, hover, and transition control analysis, (7) a performance and mission capability study, and (8) a life cycle cost analysis. A supersonic fighter aircraft with STOVL capability with the lift+lift/cruise engine cycle seems a viable option for the next generation fighter.

A tailored 200 parameter VME based data acquisition system for IBA at the Lund Ion Beam Analysis Facility - Hardware and software

NASA Astrophysics Data System (ADS)

Elfman, Mikael; Ros, Linus; Kristiansson, Per; Nilsson, E. J. Charlotta; Pallon, Jan

2016-03-01

With the recent advances towards modern Ion Beam Analysis (IBA), going from one- or few-parameter detector systems to multi-parameter systems, it has been necessary to expand and replace the more than twenty years old CAMAC based system. A new VME multi-parameter (presently up to 200 channels) data acquisition and control system has been developed and implemented at the Lund Ion Beam Analysis Facility (LIBAF). The system is based on the VX-511 Single Board Computer (SBC), acting as master with arbiter functionality and consists of standard VME modules like Analog to Digital Converters (ADC's), Charge to Digital Converters (QDC's), Time to Digital Converters (TDC's), scaler's, IO-cards, high voltage and waveform units. The modules have been specially selected to support all of the present detector systems in the laboratory, with the option of future expansion. Typically, the detector systems consist of silicon strip detectors, silicon drift detectors and scintillator detectors, for detection of charged particles, X-rays and γ-rays. The data flow of the raw data buffers out from the VME bus to the final storage place on a 16 terabyte network attached storage disc (NAS-disc) is described. The acquisition process, remotely controlled over one of the SBCs ethernet channels, is also discussed. The user interface is written in the Kmax software package, and is used to control the acquisition process as well as for advanced online and offline data analysis through a user-friendly graphical user interface (GUI). In this work the system implementation, layout and performance are presented. The user interface and possibilities for advanced offline analysis are also discussed and illustrated.

HyPEP FY06 Report: Models and Methods

DOE Office of Scientific and Technical Information (OSTI.GOV)

DOE report

2006-09-01

The Department of Energy envisions the next generation very high-temperature gas-cooled reactor (VHTR) as a single-purpose or dual-purpose facility that produces hydrogen and electricity. The Ministry of Science and Technology (MOST) of the Republic of Korea also selected VHTR for the Nuclear Hydrogen Development and Demonstration (NHDD) Project. This research project aims at developing a user-friendly program for evaluating and optimizing cycle efficiencies of producing hydrogen and electricity in a Very-High-Temperature Reactor (VHTR). Systems for producing electricity and hydrogen are complex and the calculations associated with optimizing these systems are intensive, involving a large number of operating parameter variations andmore » many different system configurations. This research project will produce the HyPEP computer model, which is specifically designed to be an easy-to-use and fast running tool for evaluating nuclear hydrogen and electricity production facilities. The model accommodates flexible system layouts and its cost models will enable HyPEP to be well-suited for system optimization. Specific activities of this research are designed to develop the HyPEP model into a working tool, including (a) identifying major systems and components for modeling, (b) establishing system operating parameters and calculation scope, (c) establishing the overall calculation scheme, (d) developing component models, (e) developing cost and optimization models, and (f) verifying and validating the program. Once the HyPEP model is fully developed and validated, it will be used to execute calculations on candidate system configurations. FY-06 report includes a description of reference designs, methods used in this study, models and computational strategies developed for the first year effort. Results from computer codes such as HYSYS and GASS/PASS-H used by Idaho National Laboratory and Argonne National Laboratory, respectively will be benchmarked with HyPEP results in the following years.« less

76 FR 68194 - Submission for OMB Review; Comment Request

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-03

... Layouts for HPBS Work Measures. OMB No.: 0970-0230. Description: There is no longer a High Performance... information on States' performance. The Transmission File Layouts form provides the format that States will... are not requesting any changes to the Transmission File Layouts form. Respondents: Respondents may...

32 CFR Appendix B to Part 247 - CE Publications

Code of Federal Regulations, 2012 CFR

2012-07-01

... liaison functions on publisher premises including monitoring and coordinating layout and design and other... coordinate layout and ensure that the preparation of editorial material is performed in such a way as to... commander's representative shall have the authority to specify newspaper advertising layout when required to...

Effects of revised consultation room design on patient-physician communication.

PubMed

Ajiboye, Folaranmi; Dong, Fanglong; Moore, Justin; Kallail, K James; Baughman, Allison

2015-01-01

To evaluate the impact of a revised consultation room design on patient-physician interaction in an outpatient setting. The growth of ambulatory medical care makes outpatient facilities the primary point of health care contact for many Americans. However, the outpatient consultation room design remains largely unchanged, despite its increased use and the adoption of technology-mediated information sharing in clinical encounter. A randomized controlled trial used a postvisit questionnaire to assess six domains of interest (satisfaction with the visit and the consultation room, mutual respect, patient trust in the physician, communication quality, people-room interaction, and interpersonal-room interaction) in two different room designs (a traditional room and an experimental room in which a pedestal table had replaced the examination table). Interpersonal-room interaction was enhanced in the experimental consultation room when compared to the traditional consultation room (p = .0038). Participants in the experimental consultation room had better access to the computer screen, increased provider information sharing, and more time engaging providers in conversation about information on the monitor. Changing the layout of a consultation room has the potential to improve interpersonal communication through better information sharing. Clinicians who are interested in maximizing the benefits of their clinical encounter should consider changing the layout of their consultation room, especially the positioning of the computer screen. © The Author(s) 2014.

46 CFR 160.076-35 - Information pamphlet.

Code of Federal Regulations, 2010 CFR

2010-10-01

... pamphlet prior to purchase. The pamphlet text and layout must be submitted to the Commandant for approval... information, instructions, or illustrations must not be included within the approved text and layout. Sample pamphlet text and layout may be obtained by contacting the Commandant. This pamphlet may be combined with...

46 CFR 160.076-35 - Information pamphlet.

Code of Federal Regulations, 2011 CFR

2011-10-01

... pamphlet prior to purchase. The pamphlet text and layout must be submitted to the Commandant for approval... information, instructions, or illustrations must not be included within the approved text and layout. Sample pamphlet text and layout may be obtained by contacting the Commandant. This pamphlet may be combined with...

Mental Layout Extrapolations Prime Spatial Processing of Scenes

ERIC Educational Resources Information Center

Gottesman, Carmela V.

2011-01-01

Four experiments examined whether scene processing is facilitated by layout representation, including layout that was not perceived but could be predicted based on a previous partial view (boundary extension). In a priming paradigm (after Sanocki, 2003), participants judged objects' distances in photographs. In Experiment 1, full scenes (target),…

Layout Geometry in Encoding and Retrieval of Spatial Memory

ERIC Educational Resources Information Center

Mou, Weimin; Liu, Xianyun; McNamara, Timothy P.

2009-01-01

Two experiments investigated whether the spatial reference directions that are used to specify objects' locations in memory can be solely determined by layout geometry. Participants studied a layout of objects from a single viewpoint while their eye movements were recorded. Subsequently, participants used memory to make judgments of relative…

76 FR 52956 - Proposed Information Collection Activity; Comment Request

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-24

... (HPBS) Transmission File Layouts for HPBS Work Measures OMB No.: 0970-0230 Description: There is no... provide us less precise information on States' performance. The Transmission File Layouts form provides... requested to transmit similar files. We are not requesting any changes to the Transmission File Layouts form...

41 CFR 102-85.35 - What definitions apply to this part?

Code of Federal Regulations, 2011 CFR

2011-01-01

..., due to its layout, design, location, or other characteristics, is unlikely to be needed by another GSA... professional techniques of planning, layout and interior design to determine the best internal location and the... definition of “tenant improvement.” Initial space layout means the specific placement of workstations...

41 CFR 102-85.35 - What definitions apply to this part?

Code of Federal Regulations, 2013 CFR

2013-07-01

..., due to its layout, design, location, or other characteristics, is unlikely to be needed by another GSA... professional techniques of planning, layout and interior design to determine the best internal location and the... definition of “tenant improvement.” Initial space layout means the specific placement of workstations...

41 CFR 102-85.35 - What definitions apply to this part?

Code of Federal Regulations, 2012 CFR

2012-01-01

..., due to its layout, design, location, or other characteristics, is unlikely to be needed by another GSA... professional techniques of planning, layout and interior design to determine the best internal location and the... definition of “tenant improvement.” Initial space layout means the specific placement of workstations...

77 FR 22376 - Airport Improvement Program (AIP) Grant Assurances

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-13

.... Additionally, the FAA is amending paragraph (a) of Sponsor Assurance 29, Airport Layout Plan, to require that... be depicted on the airport layout plan (ALP). This includes all residential and commercial through... the statutory grant assurance relating to airport layout plans to provide that a sponsor does not have...

41 CFR 102-85.35 - What definitions apply to this part?

Code of Federal Regulations, 2014 CFR

2014-01-01

..., due to its layout, design, location, or other characteristics, is unlikely to be needed by another GSA... professional techniques of planning, layout and interior design to determine the best internal location and the... definition of “tenant improvement.” Initial space layout means the specific placement of workstations...

Issues in Text Design and Layout for Computer Based Communications.

ERIC Educational Resources Information Center

Andresen, Lee W.

1991-01-01

Discussion of computer-based communications (CBC) focuses on issues involved with screen design and layout for electronic text, based on experiences with electronic messaging, conferencing, and publishing within the Australian Open Learning Information Network (AOLIN). Recommendations for research on design and layout for printed text are also…

76 FR 39256 - Airworthiness Directives; Dassault Aviation Model FALCON 7X Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-06

... include modifying the applicable wiring and layout, a general visual inspection for absence of marks of... March 3, 2010. (2) Modify the applicable wiring and layout, in accordance with the Accomplishment... modifying the applicable wiring and layout, in accordance with Dassault Mandatory Service Bulletin 7X- 006...

A case study of printing industry plant layout for effective production

NASA Astrophysics Data System (ADS)

Viswajit, T.; Teja, T. Ravi; Deepthi, Y. P.

2017-07-01

This paper presents the overall picture of the processes happening in printing industry. This research is aimed to improve the plant layout of existing plant. The travel time was reduced by relocating machinery. Relocation is based on systematic layout planning (SLP). The complete process of raw material entering the industry to dispatching of finished product is shown in 3-D Flow diagram. The process happening in each floor explained in detail using Flow Process chart. Travel time is reduced by 25% after modifying existing plant layout.

Study on workshop layout of a motorcycle company based on systematic layout planning (SLP)

NASA Astrophysics Data System (ADS)

Zhou, Kang-Qu; Zhang, Rui-Juan; Wang, Ying-Dong; Wang, Bing-Jie

2010-08-01

The method of SLP has been applied in a motorcycle company's layout planning. In this layout design, the related graphics have been used to illuminate the logistics and non-logistics relationships of every workshop to get the integrated relationships of workshops and preliminary plans. Comparing the two preliminary plans including logistics efficiency, space utilization, management conveniences, etc, an improvement solution is proposed. Through the improvement solution, the productivity has been increased by 18% and the production capacity is able to make 1600 engines each day.

[SCHWABE Company's patent portfolio of Ginkgo biloba preparation].

PubMed

Liu, Wei; Cheng, Xin-Min; Geng, Dong-Mei; Tan, Wei; Zou, Wen-Jun

2014-09-01

SCHWABE Company in German is the first and largest manufacturer of Ginkgo biloba preparation. The company not only has leading technology in this field, but also protects its own market effectively through the high quality of patent drafting and exactly patent layout. Based on multi-angle analysis for patent portfolio of G. biloba preparation at application time, legal status, globally layout, Chinese layout, the article provides technical reference of research and development of G. biloba, also provides valuable experience of traditonal Chinese medicine patent portfolio layout for Chinese enterprises.

Navigating comics: an empirical and theoretical approach to strategies of reading comic page layouts.

PubMed

Cohn, Neil

2013-01-01

Like the sequence of words in written language, comic book page layouts direct images into a deliberate reading sequence. Conventional wisdom would expect that comic panels follow the order of text: left-to-right and down - a "Z-path" - though several layouts can violate this order, such as Gestalt groupings of panels that deny a Z-path of reading. To examine how layouts pressure readers to choose pathways deviating from the Z-path, we presented participants with comic pages empty of content, and asked them to number the panels in the order they would read them. Participants frequently used strategies departing from both the traditional Z-path and Gestalt groupings. These preferences reveal a system of constraints that organizes panels into hierarchic constituents, guiding readers through comic page layouts.

Automatic Layout Design for Power Module

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ning, Puqi; Wang, Fei; Ngo, Khai

The layout of power modules is one of the most important elements in power module design, especially for high power densities, where couplings are increased. In this paper, an automatic design process using a genetic algorithm is presented. Some practical considerations are introduced in the optimization of the layout design of the module. This paper presents a process for automatic layout design for high power density modules. Detailed GA implementations are introduced both for outer loop and inner loop. As verified by a design example, the results of the automatic design process presented here are better than those from manualmore » design and also better than the results from a popular design software. This automatic design procedure could be a major step toward improving the overall performance of future layout design.« less

Production layout improvement by using line balancing and Systematic Layout Planning (SLP) at PT. XYZ

NASA Astrophysics Data System (ADS)

Buchari; Tarigan, U.; Ambarita, M. B.

2018-02-01

PT. XYZ is a wood processing company which produce semi-finished wood with production system is make to order. In the production process, it can be seen that the production line is not balanced. The imbalance of the production line is caused by the difference in cycle time between work stations. In addition, there are other issues, namely the existence of material flow pattern is irregular so it resulted in the backtracking and displacement distance away. This study aimed to obtain the allocation of work elements to specific work stations and propose an improvement of the production layout based on the result of improvements in the line balancing. The method used in the balancing is Ranked Positional Weight (RPW) or also known as Helgeson Birnie method. While the methods used in the improvement of the layout is the method of Systematic Layout Planning (SLP). By using Ranked Positional Weight (RPW) obtained increase in line efficiency becomes 84,86% and decreased balance delay becomes 15,14%. Repairing the layout using the method of Systematic Layout Planning (SLP) also give good results with a reduction in path length becomes 133,82 meters from 213,09 meters previously or a decrease of 37.2%.

An engineering methodology for implementing and testing VLSI (Very Large Scale Integrated) circuits

NASA Astrophysics Data System (ADS)

Corliss, Walter F., II

1989-03-01

The engineering methodology for producing a fully tested VLSI chip from a design layout is presented. A 16-bit correlator, NPS CORN88, that was previously designed, was used as a vehicle to demonstrate this methodology. The study of the design and simulation tools, MAGIC and MOSSIM II, was the focus of the design and validation process. The design was then implemented and the chip was fabricated by MOSIS. This fabricated chip was then used to develop a testing methodology for using the digital test facilities at NPS. NPS CORN88 was the first full custom VLSI chip, designed at NPS, to be tested with the NPS digital analysis system, Tektronix DAS 9100 series tester. The capabilities and limitations of these test facilities are examined. NPS CORN88 test results are included to demonstrate the capabilities of the digital test system. A translator, MOS2DAS, was developed to convert the MOSSIM II simulation program to the input files required by the DAS 9100 device verification software, 91DVS. Finally, a tutorial for using the digital test facilities, including the DAS 9100 and associated support equipments, is included as an appendix.

East Spar development: NCC buoy--The vertical submarine

DOE Office of Scientific and Technical Information (OSTI.GOV)

Boyle, E.C.

1998-02-01

The remote East Spar gas/condensate field has been developed using a subsea production system operated by an unmanned navigation, communication, and control (NCC) buoy. The use of this type of system allows control of the field from any convenient location, with the command-response time and the cost of the facility almost completely independent of the distance to the shore or host facility. Successes during the project (such as using model tests to prove the concept and using a tension-leg mooring system to reduce the motion response of the buoy) are discussed and compared to failures, like the weight and sizemore » growth of the structure, caused as the design requirements were finalized and external factors changed. The operation and layout of this facility is summarized, showing why it was described as a vertical submarine. Conclusions are drawn about the use of an NCC buoy to develop this field, showing that the main objectives have been achieved. The limited operating experience to date is also considered in the review of the design objectives. The paper concludes with the possibilities for the future of this type of concept.« less

Development of an open-source web-based intervention for Brazilian smokers - Viva sem Tabaco.

PubMed

Gomide, H P; Bernardino, H S; Richter, K; Martins, L F; Ronzani, T M

2016-08-02

Web-based interventions for smoking cessation available in Portuguese do not adhere to evidence-based treatment guidelines. Besides, all existing web-based interventions are built on proprietary platforms that developing countries often cannot afford. We aimed to describe the development of "Viva sem Tabaco", an open-source web-based intervention. The development of the intervention included the selection of content from evidence-based guidelines for smoking cessation, the design of the first layout, conduction of 2 focus groups to identify potential features, refinement of the layout based on focus groups and correction of content based on feedback provided by specialists on smoking cessation. At the end, we released the source-code and intervention on the Internet and translated it into Spanish and English. The intervention developed fills gaps in the information available in Portuguese and the lack of open-source interventions for smoking cessation. The open-source licensing format and its translation system may help researchers from different countries deploying evidence-based interventions for smoking cessation.

Attention promotes episodic encoding by stabilizing hippocampal representations

PubMed Central

Aly, Mariam; Turk-Browne, Nicholas B.

2016-01-01

Attention influences what is later remembered, but little is known about how this occurs in the brain. We hypothesized that behavioral goals modulate the attentional state of the hippocampus to prioritize goal-relevant aspects of experience for encoding. Participants viewed rooms with paintings, attending to room layouts or painting styles on different trials during high-resolution functional MRI. We identified template activity patterns in each hippocampal subfield that corresponded to the attentional state induced by each task. Participants then incidentally encoded new rooms with art while attending to the layout or painting style, and memory was subsequently tested. We found that when task-relevant information was better remembered, the hippocampus was more likely to have been in the correct attentional state during encoding. This effect was specific to the hippocampus, and not found in medial temporal lobe cortex, category-selective areas of the visual system, or elsewhere in the brain. These findings provide mechanistic insight into how attention transforms percepts into memories. PMID:26755611

The European XFEL Free Electron Laser at DESY

ScienceCinema

Weise, Hans [Deutsches Elektronen-Synchrotron, Germany

2017-12-09

The European X-ray Free-Electron laser Facility (XFEL) is going to be built in an international collaboration at the Deutsches Elektronen-Synchrotron (DESY), Germany, and the Technical Design Report was published in 2006. The official project is expected for summer 2007. This new facility will offer photon beams at wavelengths as short as 1 angstrom with highest peak brilliance being more than 100 million times higher than present day synchrotron radiation sources. The radiation has a high degree of transverse coherence and the pulse duration is reduced from {approx}100 picoseconds (typ. for SR light sources) down to the {approx}10 femtosecond time domain. The overall layout of the XFEL will be described. This includes the envisaged operation parameters for the linear accelerator using superconducting TESLA technology. The complete design is based on the actually operated FLASH free-electron laser at DESY. Experience with the operation during first long user runs at wavelengths from 30 to 13 nm will be described in detail.

Wayfinding: a quality factor in human design approach to healthcare facilities.

PubMed

Del Nord, R

1999-01-01

The specific aim of this paper is the systematic analysis of interactions and reciprocal conditions existing between the physical space of hospital buildings and the different categories of individuals that come in contact with them. The physical and environmental facilities of hospital architecture often influence the therapeutic character of space and the employees. If the values of the individual are to be safeguarded in this context, priority needs to be given to such factors as communication, privacy, etc. This would mean the involvement of other professional groups such as psychologists, sociologists, ergonomists, etc. at the hospital building planning stage. This paper will outline the result of some research conducted at the University Research Center "TESIS" of Florence to provide better understanding of design strategies applied to reduce the pathology of spaces within the healthcare environment. The case studies will highlight the parameters and the possible architectural solutions to wayfinding and the humanization of spaces, with particular emphasis on lay-outs, technologies, furniture and finishing design.

20 CFR 638.303 - Site selection and facilities management.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 20 Employees' Benefits 3 2010-04-01 2010-04-01 false Site selection and facilities management. 638... Facilities Management § 638.303 Site selection and facilities management. (a) The Job Corps Director shall... center, facilities engineering and real estate management will be conducted by the Job Corps Director or...

A Physics-Based Approach for Power Integrity in Multi-Layered PCBs

NASA Astrophysics Data System (ADS)

Zhao, Biyao

Developing a power distribution network (PDN) for ASICs and ICs to achieve the low-voltage ripple specifications for current digital designs is challenging with the high-speed and low-voltage ICs. Present methods are typically guided by best engineering practices for low impedance looking into the PDN from the IC. A pre-layout design methodology for power integrity in multi-layered PCB PDN geometry is proposed in the thesis. The PCB PDN geometry is segmented into four parts and every part is modelled using different methods based on the geometry details of the part. Physics-based circuit models are built for every part and the four parts are re-assembled into one model. The influence of geometry details is clearly revealed in this methodology. Based on the physics-based circuit mode, the procedures of using the pre-layout design methodology as a guideline during the PDN design is illustrated. Some common used geometries are used to build design space, and the design curves with the geometry details are provided to be a look up library for engineering use. The pre-layout methodology is based on the resonant cavity model of parallel planes for the cavity structures, and parallel-plane PEEC (PPP) for the irregular shaped plane inductance, and PEEC for the decoupling capacitor connection above the top most or bottom most power-return planes. PCB PDN is analyzed based on the input impedance looking into the PCB from the IC. The pre-layout design methodology can be used to obtain the best possible PCB PDN design. With the switching current profile, the target impedance can be selected to evaluate the PDN performance, and the frequency domain PDN input impedance can be used to obtain the voltage ripple in the time domain to give intuitive insight of the geometry impact on the voltage ripple.

Automatic digital photo-book making system

NASA Astrophysics Data System (ADS)

Wang, Wiley; Teo, Patrick; Muzzolini, Russ

2010-02-01

The diversity of photo products has grown more than ever before. A group of photos are not only printed individually, but also can be arranged in specific order to tell a story, such as in a photo book, a calendar or a poster collage. Similar to making a traditional scrapbook, digital photo book tools allow the user to choose a book style/theme, layouts of pages, backgrounds and the way the pictures are arranged. This process is often time consuming to users, given the number of images and the choices of layout/background combinations. In this paper, we developed a system to automatically generate photo books with only a few initial selections required. The system utilizes time stamps, color indices, orientations and other image properties to best fit pictures into a final photo book. The common way of telling a story is to lay the pictures out in chronological order. If the pictures are proximate in time, they will coincide with each other and are often logically related. The pictures are naturally clustered along a time line. Breaks between clusters can be used as a guide to separate pages or spreads, thus, pictures that are logically related can stay close on the same page or spread. When people are making a photo book, it is helpful to start with chronologically grouped images, but time alone wont be enough to complete the process. Each page is limited by the number of layouts available. Many aesthetic rules also apply, such as, emphasis of preferred pictures, consistency of local image density throughout the whole book, matching a background to the content of the images, and the variety of adjacent page layouts. We developed an algorithm to group images onto pages under the constraints of aesthetic rules. We also apply content analysis based on the color and blurriness of each picture, to match backgrounds and to adjust page layouts. Some of our aesthetic rules are fixed and given by designers. Other aesthetic rules are statistic models trained by using customer photo book samples. We evaluate our algorithm with test photo sets, and ask participants both quantitative and qualitative questions for feedback. We have seen the improvement on the time it takes users to produce a photo book and on the satisfaction with the overall quality.

Safety assessment in plant layout design using indexing approach: implementing inherent safety perspective. Part 1 - guideword applicability and method description.

PubMed

Tugnoli, Alessandro; Khan, Faisal; Amyotte, Paul; Cozzani, Valerio

2008-12-15

Layout planning plays a key role in the inherent safety performance of process plants since this design feature controls the possibility of accidental chain-events and the magnitude of possible consequences. A lack of suitable methods to promote the effective implementation of inherent safety in layout design calls for the development of new techniques and methods. In the present paper, a safety assessment approach suitable for layout design in the critical early phase is proposed. The concept of inherent safety is implemented within this safety assessment; the approach is based on an integrated assessment of inherent safety guideword applicability within the constraints typically present in layout design. Application of these guidewords is evaluated along with unit hazards and control devices to quantitatively map the safety performance of different layout options. Moreover, the economic aspects related to safety and inherent safety are evaluated by the method. Specific sub-indices are developed within the integrated safety assessment system to analyze and quantify the hazard related to domino effects. The proposed approach is quick in application, auditable and shares a common framework applicable in other phases of the design lifecycle (e.g. process design). The present work is divided in two parts: Part 1 (current paper) presents the application of inherent safety guidelines in layout design and the index method for safety assessment; Part 2 (accompanying paper) describes the domino hazard sub-index and demonstrates the proposed approach with a case study, thus evidencing the introduction of inherent safety features in layout design.

Comparing taxi clearance input layouts for advancements in flight deck automation for surface operations

NASA Astrophysics Data System (ADS)

Cheng, Lara W. S.

Airport moving maps (AMMs) have been shown to decrease navigation errors, increase taxiing speed, and reduce workload when they depict airport layout, current aircraft position, and the cleared taxi route. However, current technologies are limited in their ability to depict the cleared taxi route due to the unavailability of datacomm or other means of electronically transmitting clearances from ATC to the flight deck. This study examined methods by which pilots can input ATC-issued taxi clearances to support taxi route depictions on the AMM. Sixteen general aviation (GA) pilots used a touchscreen monitor to input taxi clearances using two input layouts, softkeys and QWERTY, each with and without feedforward (graying out invalid inputs). QWERTY yielded more taxi route input errors than the softkeys layout. The presence of feedforward did not produce fewer taxi route input errors than in the non-feedforward condition. The QWERTY layout did reduce taxi clearance input times relative to the softkeys layout, but when feedforward was present this effect was observed only for the longer, 6-segment taxi clearances. It was observed that with the softkeys layout, feedforward reduced input times compared to non-feedforward but only for the 4-segment clearances. Feedforward did not support faster taxi clearance input times for the QWERTY layout. Based on the results and analyses of the present study, it is concluded that for taxi clearance inputs, (1) QWERTY remain the standard for alphanumeric inputs, and (2) feedforward be investigated further, with a focus on participant preference and performance of black-gray contrast of keys.

Layout as Political Expression: Visual Literacy and the Peruvian Press.

ERIC Educational Resources Information Center

Barnhurst, Kevin G.

Newspaper layout and design studies ignore politics, and most studies of newspaper politics ignore visual design. News layout is generally thought to be a set of neutral, efficient practices. This study suggests that the political position of Peruvian newspapers parallels their visual presentation of terrorism. The liberal "La Republica"…

Two-Year-Old Children Interpret Abstract, Purely Geometric Maps

ERIC Educational Resources Information Center

Winkler-Rhoades, Nathan; Carey, Susan C.; Spelke, Elizabeth S.

2013-01-01

In two experiments, 2.5-year-old children spontaneously used geometric information from 2D maps to locate objects in a 3D surface layout, without instruction or feedback. Children related maps to their corresponding layouts even though the maps differed from the layouts in size, mobility, orientation, dimensionality, and perspective, and even when…

Automatic Layout Design for Power Module

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ning, Puqi; Wang, Fei; Ngo, Khai

The layout of power modules is one of the key points in power module design, especially for high power densities, where couplings are increased. In this paper, along with the design example, an automatic design processes by using a genetic algorithm are presented. Some practical considerations and implementations are introduced in the optimization of module layout design.

49 CFR 238.447 - Train operator's controls and power car cab layout.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 4 2011-10-01 2011-10-01 false Train operator's controls and power car cab layout... layout. (a) Train operator controls in the power car cab shall be arranged so as to minimize the chance.... (d) Power car cab information displays shall be designed with the following characteristics: (1...

49 CFR 238.447 - Train operator's controls and power car cab layout.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 49 Transportation 4 2013-10-01 2013-10-01 false Train operator's controls and power car cab layout... layout. (a) Train operator controls in the power car cab shall be arranged so as to minimize the chance.... (d) Power car cab information displays shall be designed with the following characteristics: (1...

49 CFR 238.447 - Train operator's controls and power car cab layout.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 49 Transportation 4 2012-10-01 2012-10-01 false Train operator's controls and power car cab layout... layout. (a) Train operator controls in the power car cab shall be arranged so as to minimize the chance.... (d) Power car cab information displays shall be designed with the following characteristics: (1...

Student Perceptions of Textbook Layout and Learnability in Private Schools

ERIC Educational Resources Information Center

Hoshangabadwala, Alefiyah

2015-01-01

This research is an exploratory study that investigates students' perceptions pertinent to textbook layout and organization and their evaluation of the textbook ease of learning. The objective is to find out whether the layout dynamics of school textbooks make any difference in students' interest in studying or subject understanding. 73 students…

Gender Differences in Student Attitude for Seating Layout in College Classrooms

ERIC Educational Resources Information Center

Burgess, Brigitte; Kaya, Naz

2007-01-01

This study examined whether gender influenced college students' attitudes regarding classroom seating layout. Seating layouts included: a) rows of tablet-arm chairs, b) U-shaped, c) clusters, and d) rows of tables with individual chairs. The sample consisted of 912 college students. Factor analysis yielded two dimensions: "Feeling at Ease" and…

Layout of the LER (Low Energy Ring) Arc

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hutton, A.

We have recently been trying to accumulate all of the information necessary to decide on the layout of the regular curved arcs of the Low Energy Ring (LER) and there have been several ABC Notes published on different aspects of the problem. This note will describe the layout that has been derived from these considerations.

A flexible layout design method for passive micromixers.

PubMed

Deng, Yongbo; Liu, Zhenyu; Zhang, Ping; Liu, Yongshun; Gao, Qingyong; Wu, Yihui

2012-10-01

This paper discusses a flexible layout design method of passive micromixers based on the topology optimization of fluidic flows. Being different from the trial and error method, this method obtains the detailed layout of a passive micromixer according to the desired mixing performance by solving a topology optimization problem. Therefore, the dependence on the experience of the designer is weaken, when this method is used to design a passive micromixer with acceptable mixing performance. Several design disciplines for the passive micromixers are considered to demonstrate the flexibility of the layout design method for passive micromixers. These design disciplines include the approximation of the real 3D micromixer, the manufacturing feasibility, the spacial periodic design, and effects of the Péclet number and Reynolds number on the designs obtained by this layout design method. The capability of this design method is validated by several comparisons performed between the obtained layouts and the optimized designs in the recently published literatures, where the values of the mixing measurement is improved up to 40.4% for one cycle of the micromixer.

A compact and realistic cerebral cortical layout derived from prewhitened resting-state fMRI time series: Cherniak's adjacency rule, size law, and metamodule grouping upheld

PubMed Central

Lewis, Scott M.; Christova, Peka; Jerde, Trenton A.; Georgopoulos, Apostolos P.

2012-01-01

We used hierarchical tree clustering to derive a functional organizational chart of 52 human cortical areas (26 per hemisphere) from zero-lag correlations calculated between single-voxel, prewhitened, resting-state BOLD fMRI time series in 18 subjects. No special “resting-state networks” were identified. There were four major features in the resulting tree (dendrogram). First, there was a strong clustering of homotopic, left-right hemispheric areas. Second, cortical areas were concatenated in multiple, partially overlapping clusters. Third, the arrangement of the areas revealed a layout that closely resembled the actual layout of the cerebral cortex, namely an orderly progression from anterior to posterior. And fourth, the layout of the cortical areas in the tree conformed to principles of efficient, compact layout of components proposed by Cherniak. Since the tree was derived on the basis of the strength of neural correlations, these results document an orderly relation between functional interactions and layout, i.e., between structure and function. PMID:22973198

Compilation of Blast Parameters of Selected High Explosives, Propellants, and Pyrotechnics in Surface Burst Configurations.

DTIC Science & Technology

1987-01-01

APPENDIX B- DATA REDUCTION PROGRAM .............................. 403 LIST OF ILLUSTRATIONS FIGURE NO. PAGE 1. Instrumented Test Pad Layout...weight to produce the same yield relative to hemis- pherical TNT. The test specimens were placed at ground zero in a particular in- plant geometry...The containers were either scaled from the original size or tested in full- scale configurations. The test charges were placed at ground zero and

Heat Recovery Incinerator-Equipment Selection and Plant Layout for Safety, Human Engineering and Maintainability.

DTIC Science & Technology

1984-10-01

16 4.2 Solid Waste Receiving and Storage Area ........................ 17 4.3 Equipment Location and Spacing...10OROS (Ccr4n-ifl. **,0d. d - -eet -.d tdonfffy by bltk -P-+) HRI, RAM, Human factors, HRI design, IRI safety, solid waste , energy recovery 10 AOSTNACT...health and safety hazards to individuals hand-sorting the conglomerate of solid waste , the potential of dangerous substances and inflammable or ex

Development of a Star Tracker-Based Reference System for Accurate Attitude Determination of a Simulated Spacecraft

DTIC Science & Technology

2012-03-01

the mathematical pretext for quaternions, which summarizes as: In three- dimensional space , any displacement of a rigid body such that a ...for the patch board was selected, with a uniform 8 mm spacing between LED centers. Figure 33 is schematic of the patch board layout, and Fig. 34 shows...attitude determination since the dawn of the space age. Without accurate attitude determination, a “Lost- in-

Improved heliostat field design for solar tower plants

NASA Astrophysics Data System (ADS)

Collado, Francisco J.; Guallar, Jesús

2017-06-01

In solar power tower (SPT) systems, selecting the optimum location of thousands of heliostats and the most profitable tower height and receiver size remains a challenge. Campo code is prepared for the detailed design of such plants in particular, the optimum layout, provided that the plant size is known. Therefore, less exhaustive codes, as DELSOL3, are also needed to perform preliminary parametric analysis that narrows the most economic size of the plant.

Occupational Strength Testing Related to Gender-Neutral Issues in Naval Aviation: A Selected Bibliography.

DTIC Science & Technology

1995-02-01

the deficiency in using the DoD survey in designing escape system tests covering female aviators. Further, analysis of two existing anthropometric...sinusoidally in all 5 contractions with a peak endurance midway through the ovulatory phase and the lowest endurance mid-way through the luteal phase...goals, and identifies deficiencies in the crewstation layout of mockups and aircraft undergoing development. 96 Reilly, R. R.; Zedeck, S.; Tenopyr, M. L