Erosion of iron-chromium alloys by glass particles

NASA Technical Reports Server (NTRS)

Salik, J.; Buckley, D. H.

1984-01-01

The material loss upon erosion was measured for several iron-chromium alloys. Two types of erodent material were used: spherical glass beads and sharp particles of crushed glass. For erosion with glass beads the erosion resistance (defined as the reciprocal of material loss rate) was linearly dependent on hardness. This is in accordance with the erosion behavior of pure metals, but contrary to the erosion behavior of alloys of constant composition that were subjected to different heat treatments. For erosion with crushed glass, however, no correlation existed between hardness and erosion resistance. Instead, the erosion resistance depended on alloy composition rather than on hardness and increased with the chromium content of the alloy. The difference in erosion behavior for the two types of erodent particles suggested that two different material removal mechanisms were involved. This was confirmed by SEM micrographs of the eroded surfaces, which showed that for erosion with glass beads the mechanism of material removal was deformation-induced flaking of surface layers, or peening, whereas for erosion with crushed glass it was cutting or chopping.

Erosion at decommissioned road-stream crossings: case studies from three northern California watersheds

Treesearch

Sam A. Flanagan; David Fuller; Leonard Job; Sam Morrison

2012-01-01

Post-treatment erosion was observed for 41 decommissioned road stream crossings in three northern California watersheds. Sites were purposefully selected in order to characterize the nature and range of post-treatment erosional responses. Sites with the highest visible erosion were selected in order to better understand the dominant process and incorporate any...

Erosion characteristics and horizontal variability for small erosion depths in the Sacramento-San Joaquin River Delta, California, USA

NASA Astrophysics Data System (ADS)

Schoellhamer, David H.; Manning, Andrew J.; Work, Paul A.

2017-06-01

Erodibility of cohesive sediment in the Sacramento-San Joaquin River Delta (Delta) was investigated with an erosion microcosm. Erosion depths in the Delta and in the microcosm were estimated to be about one floc diameter over a range of shear stresses and times comparable to half of a typical tidal cycle. Using the conventional assumption of horizontally homogeneous bed sediment, data from 27 of 34 microcosm experiments indicate that the erosion rate coefficient increased as eroded mass increased, contrary to theory. We believe that small erosion depths, erosion rate coefficient deviation from theory, and visual observation of horizontally varying biota and texture at the sediment surface indicate that erosion cannot solely be a function of depth but must also vary horizontally. We test this hypothesis by developing a simple numerical model that includes horizontal heterogeneity, use it to develop an artificial time series of suspended-sediment concentration (SSC) in an erosion microcosm, then analyze that time series assuming horizontal homogeneity. A shear vane was used to estimate that the horizontal standard deviation of critical shear stress was about 30% of the mean value at a site in the Delta. The numerical model of the erosion microcosm included a normal distribution of initial critical shear stress, a linear increase in critical shear stress with eroded mass, an exponential decrease of erosion rate coefficient with eroded mass, and a stepped increase in applied shear stress. The maximum SSC for each step increased gradually, thus confounding identification of a single well-defined critical shear stress as encountered with the empirical data. Analysis of the artificial SSC time series with the assumption of a homogeneous bed reproduced the original profile of critical shear stress, but the erosion rate coefficient increased with eroded mass, similar to the empirical data. Thus, the numerical experiment confirms the small-depth erosion hypothesis. A linear model of critical shear stress and eroded mass is proposed to simulate small-depth erosion, assuming that the applied and critical shear stresses quickly reach equilibrium.

Erosion characteristics and horizontal variability for small erosion depths in the Sacramento-San Joaquin River Delta, California, USA

USGS Publications Warehouse

Schoellhamer, David H.; Manning, Andrew J.; Work, Paul A.

2017-01-01

Erodibility of cohesive sediment in the Sacramento-San Joaquin River Delta (Delta) was investigated with an erosion microcosm. Erosion depths in the Delta and in the microcosm were estimated to be about one floc diameter over a range of shear stresses and times comparable to half of a typical tidal cycle. Using the conventional assumption of horizontally homogeneous bed sediment, data from 27 of 34 microcosm experiments indicate that the erosion rate coefficient increased as eroded mass increased, contrary to theory. We believe that small erosion depths, erosion rate coefficient deviation from theory, and visual observation of horizontally varying biota and texture at the sediment surface indicate that erosion cannot solely be a function of depth but must also vary horizontally. We test this hypothesis by developing a simple numerical model that includes horizontal heterogeneity, use it to develop an artificial time series of suspended-sediment concentration (SSC) in an erosion microcosm, then analyze that time series assuming horizontal homogeneity. A shear vane was used to estimate that the horizontal standard deviation of critical shear stress was about 30% of the mean value at a site in the Delta. The numerical model of the erosion microcosm included a normal distribution of initial critical shear stress, a linear increase in critical shear stress with eroded mass, an exponential decrease of erosion rate coefficient with eroded mass, and a stepped increase in applied shear stress. The maximum SSC for each step increased gradually, thus confounding identification of a single well-defined critical shear stress as encountered with the empirical data. Analysis of the artificial SSC time series with the assumption of a homogeneous bed reproduced the original profile of critical shear stress, but the erosion rate coefficient increased with eroded mass, similar to the empirical data. Thus, the numerical experiment confirms the small-depth erosion hypothesis. A linear model of critical shear stress and eroded mass is proposed to simulate small-depth erosion, assuming that the applied and critical shear stresses quickly reach equilibrium.

Investigation of the dynamics of ephemeral gully erosion on arable land of the forest-steppe and steppe zone of the East of the Russian Plain from remote sensing data

NASA Astrophysics Data System (ADS)

Platoncheva, E. V.

2018-01-01

Spatio-temporal estimation of the erosion of arable soils is still an urgent task, in spite of the numerous methods of such assessments. Development of information technologies, the emergence of high and ultra-high resolution images allows reliable identification of linear forms of erosion to determine its dynamics on arable land. The study drew attention to the dynamics of the most active erosion unit - an ephemeral gully. The estimation of the dynamics was carried out on the basis of different space images for the maximum possible period (from 1986 to 2016). The cartographic method was used as the main research method. Identification of a belt of ephemeral gully erosion based on materials of multi-zone space surveys and GIS-technology of their processing was carried out. In the course of work with satellite imagery and subsequent verification of the received data on the ground, the main signs of deciphering the ephemeral gully network were determined. A methodology for geoinformation mapping of the dynamics of ephemeral gully erosion belt was developed and a system of indicators quantitatively characterizing its development on arable slopes was proposed. The evaluation of the current ephemeral gully network based on the interpretation of space images includes the definition of such indicators of ephemeral gully erosion as the density of the ephemeral gully net, the density of the ephemeral gullies, the area and linear dynamics of the ephemeral gully network. Preliminary results of the assessment of the dynamics of the belt erosion showed an increase in all quantitative indicators of ephemeral gully erosion for the observed period.

Prevention of dentine erosion by brushing with anti-erosive toothpastes.

PubMed

Aykut-Yetkiner, Arzu; Attin, Thomas; Wiegand, Annette

2014-07-01

This in vitro study aimed to investigate the preventive effect of brushing with anti-erosive toothpastes compared to a conventional fluoride toothpaste on dentine erosion. Bovine dentine specimens (n=12 per subgroup) were eroded in an artificial mouth (6 days, 6×30 s/day) using either citric acid (pH:2.5) or a hydrochloric acid/pepsin solution (pH:1.6), simulating extrinsic or intrinsic erosive conditions, respectively. In between, the specimens were rinsed with artificial saliva. Twice daily, the specimens were brushed for 15 s in an automatic brushing machine at 2.5 N with a conventional fluoride toothpaste slurry (elmex, AmF) or toothpaste slurries with anti-erosive formulations: Apacare (NaF/1% nHAP), Biorepair (ZnCO3-HAP), Chitodent (Chitosan), elmex Erosionsschutz (NaF/AmF/SnCl2/Chitosan), mirasensitive hap (NaF/30% HAP), Sensodyne Proschmelz (NaF/KNO3). Unbrushed specimens served as control. Dentine loss was measured profilometrically and statistically analysed using two-way and one-way ANOVA followed by Scheffe's post hoc tests. RDA-values of all toothpastes were determined, and linear mixed models were applied to analyse the influence of toothpaste abrasivity on dentine wear (p<0.05). Dentine erosion of unbrushed specimens amounted to 5.1±1.0 μm (extrinsic conditions) and 12.9±1.4 μm (intrinsic conditions). All toothpastes significantly reduced dentine erosion by 24-67% (extrinsic conditions) and 21-40% (intrinsic conditions). Biorepair was least effective, while all other toothpastes were not significantly different from each other. Linear mixed models did not show a significant effect of the RDA-value of the respective toothpaste on dentine loss. Toothpastes with anti-erosive formulations reduced dentine erosion, especially under simulated extrinsic erosive conditions, but were not superior to a conventional fluoride toothpaste. Copyright © 2014 Elsevier Ltd. All rights reserved.

The effect of choosing three different C factor formulae derived from NDVI on a fully raster-based erosion modelling

NASA Astrophysics Data System (ADS)

Sulistyo, Bambang

2016-11-01

The research was aimed at studying the efect of choosing three different C factor formulae derived from NDVI on a fully raster-based erosion modelling of The USLE using remote sensing data and GIS technique. Methods applied was by analysing all factors affecting erosion such that all data were in the form of raster. Those data were R, K, LS, C and P factors. Monthly R factor was evaluated based on formula developed by Abdurachman. K factor was determined using modified formula used by Ministry of Forestry based on soil samples taken in the field. LS factor was derived from Digital Elevation Model. Three C factors used were all derived from NDVI and developed by Suriyaprasit (non-linear) and by Sulistyo (linear and non-linear). P factor was derived from the combination between slope data and landcover classification interpreted from Landsat 7 ETM+. Another analysis was the creation of map of Bulk Density used to convert erosion unit. To know the model accuracy, model validation was done by applying statistical analysis and by comparing Emodel with Eactual. A threshold value of ≥ 0.80 or ≥ 80% was chosen to justify. The research result showed that all Emodel using three formulae of C factors have coeeficient of correlation value of > 0.8. The results of analysis of variance showed that there was significantly difference between Emodel and Eactual when using C factor formula developed by Suriyaprasit and Sulistyo (non-linear). Among the three formulae, only Emodel using C factor formula developed by Sulistyo (linear) reached the accuracy of 81.13% while the other only 56.02% as developed by Sulistyo (nonlinear) and 4.70% as developed by Suriyaprasit, respectively.

Solid impingement erosion mechanisms and characterization of erosion resistance of ductile metals

NASA Technical Reports Server (NTRS)

Rao, V. P.; Buckley, D. H.

1982-01-01

Experimental results pertaining to spherical glass bead and angular crushed glass particle impingement are presented. A concept of energy adsorption to explain the failure of material is proposed. The erosion characteristics of several pure metals were correlated with the proposed energy parameters and with other properties. Correlations of erosion and material properties were also carried out with these materials to study the effect of the angle of impingement. Analyses of extensive erosion data indicate that surface energy, strain energy, melting point, bulk modulus, hardness, ultimate resilience, atomic volume and product of linear coefficient of thermal expansion, bulk modulus, and temperature rise required for melting, and ultimate resilience, and hardness exhibit the best correlations. It appears that both energy and thermal properties contribute to the total erosion.

Comparing global-scale topographic and climatic metrics to long-term erosion rates using ArcSwath, an efficient new ArcGIS tool for swath profile analysis

NASA Astrophysics Data System (ADS)

Blomqvist, Niclas; Whipp, David

2016-04-01

The topography of the Earth's surface is the result of the interaction of tectonics, erosion and climate. Thus, topography should contain a record of these processes that can be extracted by topographic analysis. The question considered in this study is whether the spatial variations in erosion that have sculpted the modern topography are representative of the long-term erosion rates in mountainous regions. We compare long-term erosion rates derived from low-temperature thermochronometry to erosional proxies calculated from topographic and climatic data analysis. The study has been performed on a global scale including six orogens: The Himalaya, Andes, Taiwan, Olympic Mountains, Southern Alps in New Zealand and European Alps. The data was analyzed using a new swath profile analysis tool for ArcGIS called ArcSwath (https://github.com/HUGG/ArcSwath) to determine the correlations between the long-term erosion rates and modern elevations, slope angles, relief in 2.5-km- and 5-km-diameter circles, erosion potential, normalized channel steepness index ksn, and annual rainfall. ArcSwath uses a Python script that has been incorporated into an ArcMap 10.2 add-in tool, extracting swath profiles in about ten seconds compared to earlier workflows that could take more than an hour. In ArcMap, UTM-projected point or raster files can be used for creating swath profiles. Point data are projected onto the swath and the statistical parameters (minimum, mean and maximum of the values across the swath) are calculated for the raster data. Both can be immediately plotted using the Python matplotlib library, or plotted externally using the csv-file that is produced by ArcSwath. When raster and point data are plotted together, it is easier to make comparisons and see correlations between the selected data. An unambiguous correlation between the topographic or climatic metrics and long-term erosion rates was not found. Fitting of linear regression lines to the topographic/ climatic metric data and the long-term erosion rates shows that 86 of 288 plots (30%) have "good" R2 values (> 0.35) and 135 of 288 (47%) have an "acceptable" R2 value (> 0.2). The "good" and "acceptable" values have been selected on the basis of visual fit to the regression line. The majority of the plots with a "good" correlation value have positive correlations, while 11/86 plots have negative slopes for the regression lines. Interestingly, two topographic profile shapes were clear in swath profiles: Concave-up (e.g., the central-western Himalaya and the northern Bolivian Andes) and concave-down or straight (e.g., the eastern Himalayas and the southern Bolivian Andes). On the orogen scale, the concave-up shape is often related to relatively high precipitation and erosion rates on the slopes of steep topography. The concave-down/straight profiles seem to occur in association of low rainfall and/or erosion rates. Though we cannot say with confidence, the lack of a clear correlation between long-term erosion rates and climate or topography may be due to the difference in their respective timescales as climate can vary over shorter timescales than 105-107 years. In that case, variations between fluvial and glacial erosion may have overprinted the erosional effects of one another.

Cavitation erosion - scale effect and model investigations

NASA Astrophysics Data System (ADS)

Geiger, F.; Rutschmann, P.

2015-12-01

The experimental works presented in here contribute to the clarification of erosive effects of hydrodynamic cavitation. Comprehensive cavitation erosion test series were conducted for transient cloud cavitation in the shear layer of prismatic bodies. The erosion pattern and erosion rates were determined with a mineral based volume loss technique and with a metal based pit count system competitively. The results clarified the underlying scale effects and revealed a strong non-linear material dependency, which indicated significantly different damage processes for both material types. Furthermore, the size and dynamics of the cavitation clouds have been assessed by optical detection. The fluctuations of the cloud sizes showed a maximum value for those cavitation numbers related to maximum erosive aggressiveness. The finding suggests the suitability of a model approach which relates the erosion process to cavitation cloud dynamics. An enhanced experimental setup is projected to further clarify these issues.

Climatic controls on the pace of glacier erosion

NASA Astrophysics Data System (ADS)

Koppes, Michele; Hallet, Bernard; Rignot, Eric; Mouginot, Jeremie; Wellner, Julia; Love, Katherine

2016-04-01

Mountain ranges worldwide have undergone large-scale modification due the erosive action of ice, yet the mechanisms that control the timing of this modification and the rate by which ice erodes remain poorly understood. Available data report a wide range of erosion rates from individual ice masses over varying timescales, suggesting that modern erosion rates exceed orogenic rates by 2-3 orders of magnitude. These modern rates are presumed to be due to dynamic acceleration of the ice masses during deglaciation and retreat. Recent numerical models have focused on replicating the processes that produce the geomorphic signatures of glacial landscapes. Central to these models is a simple quantitative index that relates erosion rate to ice dynamics and to climate. To provide such an index, we examined explicitly the factors controlling modern glacier erosion rates across climatic regimes. Holding tectonic history, bedrock lithology and glacier hypsometries relatively constant across a latitudinal transect from Patagonia to the Antarctic Peninsula, we find that modern, basin-averaged erosion rates vary by three orders of magnitude, from 1->10 mm yr-1 for temperate tidewater glaciers to 0.01-<0.1 mm yr-1 for polar outlet glaciers, largely as a function of temperature and basal thermal regime. Erosion rates also increase non-linearly with both the sliding speed and the ice flux through the ELA, in accord with theory. The general relationship between ice dynamics and erosion suggests that the erosion rate scales non-linearly with basal sliding speed, with an exponent n ≈ 2-2.62. Notably, erosion rates decrease by over two orders of magnitude between temperate and polar glaciers with similar ice discharge rates. The difference in erosion rates between temperate and colder glaciers of similar shape and size is primarily related to the abundance of meltwater accessing the bed. Since all glaciers worldwide have experienced colder than current climatic conditions, the 100-fold decrease in long-term relative to modern erosion rates may in part reflect the temporal averaging of warm and cold-based conditions over the lifecycle of these glaciers. Higher temperatures and precipitation rates at the end of glaciations favor the production of water from rainfall, surface melting and internal melting, which promotes sliding, erosion and sediment production and evacuation from under the ice. Hence, climatic variation, more than the extent of ice cover or ice volume, controls the pace at which glaciers shape mountains.

Linear infrastructure impacts on landscape hydrology.

PubMed

Raiter, Keren G; Prober, Suzanne M; Possingham, Hugh P; Westcott, Fiona; Hobbs, Richard J

2018-01-15

The extent of roads and other forms of linear infrastructure is burgeoning worldwide, but their impacts are inadequately understood and thus poorly mitigated. Previous studies have identified many potential impacts, including alterations to the hydrological functions and soil processes upon which ecosystems depend. However, these impacts have seldom been quantified at a regional level, particularly in arid and semi-arid systems where the gap in knowledge is the greatest, and impacts potentially the most severe. To explore the effects of extensive track, road, and rail networks on surface hydrology at a regional level we assessed over 1000 km of linear infrastructure, including approx. 300 locations where ephemeral streams crossed linear infrastructure, in the largely intact landscapes of Australia's Great Western Woodlands. We found a high level of association between linear infrastructure and altered surface hydrology, with erosion and pooling 5 and 6 times as likely to occur on-road than off-road on average (1.06 erosional and 0.69 pooling features km -1 on vehicle tracks, compared with 0.22 and 0.12 km -1 , off-road, respectively). Erosion severity was greater in the presence of tracks, and 98% of crossings of ephemeral streamlines showed some evidence of impact on water movement (flow impedance (62%); diversion of flows (73%); flow concentration (76%); and/or channel initiation (31%)). Infrastructure type, pastoral land use, culvert presence, soil clay content and erodibility, mean annual rainfall, rainfall erosivity, topography and bare soil cover influenced the frequency and severity of these impacts. We conclude that linear infrastructure frequently affects ephemeral stream flows and intercepts natural overland and near-surface flows, artificially changing site-scale moisture regimes, with some parts of the landscape becoming abnormally wet and other parts becoming water-starved. In addition, linear infrastructure frequently triggers or exacerbates erosion, leading to soil loss and degradation. Where linear infrastructure densities are high, their impacts on ecological processes are likely to be considerable. Linear infrastructure is widespread across much of this relatively intact region, but there remain areas with very low infrastructure densities that need to be protected from further impacts. There is substantial scope for mitigating the impacts of existing and planned infrastructure developments. Copyright © 2017 Elsevier Ltd. All rights reserved.

Soil erosion-runoff relationships: insights from laboratory studies

NASA Astrophysics Data System (ADS)

Mamedov, Amrakh; Warrington, David; Levy, Guy

2016-04-01

Understanding the processes and mechanisms affecting runoff generation and subsequent soil erosion in semi-arid regions is essential for the development of improved soil and water conservation management practices. Using a drip type laboratory rain simulator, we studied runoff and soil erosion, and the relationships between them, in 60 semi-arid region soils varying in their intrinsic properties (e.g., texture, organic matter) under differing extrinsic conditions (e.g., rain properties, and conditions prevailing in the field soil). Both runoff and soil erosion were significantly affected by the intrinsic soil and rain properties, and soil conditions within agricultural fields or watersheds. The relationship between soil erosion and runoff was stronger when the rain kinetic energy was higher rather than lower, and could be expressed either as a linear or exponential function. Linear functions applied to certain limited cases associated with conditions that enhanced soil structure stability, (e.g., slow wetting, amending with soil stabilizers, minimum tillage in clay soils, and short duration exposure to rain). Exponential functions applied to most of the cases under conditions that tended to harm soil stability (e.g., fast wetting of soils, a wide range of antecedent soil water contents and rain kinetic energies, conventional tillage, following biosolid applications, irrigation with water of poor quality, consecutive rain simulations). The established relationships between runoff and soil erosion contributed to a better understanding of the mechanisms governing overland flow and soil loss, and could assist in (i) further development of soil erosion models and research techniques, and (ii) the design of more suitable management practices for soil and water conservation.

Predicting landslides in clearcut patches

Treesearch

Raymond M. Rice; Norman H. Pillsbury

1982-01-01

Abstract - Accelerated erosion in the form of landslides can be an undesirable consequence of clearcut logging on steep slopes. Forest managers need a method of predicting the risk of such erosion. Data collected after logging in a granitic area of northwestern California were used to develop a predictive equation. A linear discriminant function was developed that...

Critical assessment of jet erosion test methodologies for cohesive soil and sediment

USDA-ARS?s Scientific Manuscript database

The submerged Jet Erosion Test (JET) is a commonly used technique to assess the erodibility of cohesive soil. Employing a linear excess shear stress equation and impinging jet theory, simple numerical methods have been developed to analyze data collected using a JET to determine the critical shear s...

Categorization of erosion control matting for slope applications.

DOT National Transportation Integrated Search

2013-12-25

Erosion control is an important aspect of any Georgia Department of Transportation (GDOT) construction project, with the extreme negative impacts of high sediment loads in natural waterways having been well documented. Selection of a proper erosion c...

The influence of frequently consumed beverages and snacks on dental erosion among preschool children in Saudi Arabia.

PubMed

Al-Dlaigan, Yousef H; Al-Meedania, Laila A; Anil, Sukumaran

2017-12-11

To determine the prevalence of dental erosion and its association to commonly used beverages and snacks among 3 to 5 year old preschool children in Riyadh, Saudi Arabia. Three hundred eighty-eight preschool children between 3 and 5 years old were selected from 10 different schools using a cluster random sample selection; there were 184 (47%) boys and 204 (53%) girls. The surfaces of each tooth were examined for erosion, and the level of tooth wear was recorded. Data on the frequently used beverages and snacks were obtained by questionnaires completed by the parents of the preschool children. Among the 388 children examined, 47% exhibited low erosion, 10% exhibited moderate erosion and 4% exhibited severe erosion. There was no statistically significant difference between boys and girls in terms of the prevalence of erosion. Sixty percent of the children regularly consumed juice drinks. Among daily consumers, 84% of children showed erosion prevalence with strongly significant association (p < 0.005). Holding the drink in the mouth also showed a significant association with erosion (p < 0.02). It was concluded that an association was found between the prevalence of dental erosion and the frequency of citrus and carbonated juice consumed by the preschool children in Saudi Arabia.

Beach erosion and nest site selection by the leatherback sea turtle Dermochelys coriacea (Testudines: Dermochelyidae) and implications for management practices at Playa Gandoca, Costa Rica.

PubMed

Spanier, Matthew J

2010-12-01

Leatherback sea turtles (Dermochelys coriacea) nest on dynamic, erosion-prone beaches. Erosive processes and resulting nest loss have long been presumed to be a hindrance to clutch survival. In order to better understand how leatherbacks cope with unstable nesting beaches, I investigated the role of beach erosion in leatherback nest site selection at Playa Gandoca, Costa Rica. I also examined the potential effect of nest relocation, a conservation strategy in place at Playa Gandoca to prevent nest loss to erosion, on the temperature of incubating clutches. I monitored changes in beach structure as a result of erosion at natural nest sites during the time the nest was laid, as well as in subsequent weeks. To investigate slope as a cue for nest site selection, I measured the slope of the beach where turtles ascended from the sea to nest, as well as the slopes at other random locations on the beach for comparison. I examined temperature differences between natural and relocated nest sites with thermocouples placed in the sand at depths typical of leatherback nests. Nests were distributed non-randomly in a clumped distribution along the length of the beach and laid at locations that were not undergoing erosion. The slope at nest sites was significantly different than at randomly chosen locations on the beach. The sand temperature at nest depths was significantly warmer at natural nest sites than at locations of relocated nests. The findings of this study suggest leatherbacks actively select nest sites that are not undergoing erosive processes, with slope potentially being used as a cue for site selection. The relocation of nests appears to be inadvertently cooling the nest environment. Due to the fact that leatherback clutches undergo temperature-dependent sex determination, the relocation of nests may be producing an unnatural male biasing of hatchlings. The results of this study suggest that the necessity of relocation practices, largely in place to protect nests from erosion, should be reevaluated to ensure the proper conservation of this critically endangered species.

Simwe model application on susceptibility analysis to linear erosion: a case study in Alto Douro wine region.

NASA Astrophysics Data System (ADS)

Fernandes, Joana; Bateira, Carlos; Soares, Laura; Faria, Ana; Moura, Rui; Gonçalves, José

2016-04-01

The wine production in Alto Douro Wine Region - one of the world's oldest regulated and demarcated wine region - is based on a slope system organized in agricultural terraces once supported exclusively by dry stone walls. It has been undergoing the necessary changes for the introduction of technological innovations partially associated to the mechanization of vineyards work. In this sense, different forms of terrain framing have been implemented, namely the substitution of stone walls by earth embankments. This evolution raises a group of problems related to the hydric soil erosion and landscape preservation, since Alto Douro Wine Region is classified as UNESCO World Heritage Site since 2001. The study area is mostly occupied by vineyards planted in the agriculture terraces without continuous vegetation, the flow proceeds superficially influenced by the weak infiltration capacity and hydraulic conductivity. So, because of this conditioning factor the erosive features present non-significant depth, and the length thereof is limited essentially by the slope of the land, where was registered 64 gullies and 78 rills This paper focuses on the evaluation of susceptibility to linear erosion, through the application of SIMWE (SIMulated Water Erosion), (Mitas and Mitasova, 1998), using a digital elevation model, with pixel of one square meter of spatial resolution, created through detail aerial photographs, (side pixel of 50 cm), submitted to automatic stereo-correlation procedures in Agisoft PhotoScan software. The results provided by the model are compared with hydrological characteristics of the soil, (infiltration capacity, and hydraulic conductivity), soil texture, and soil structure parameters (identified by electrical resistivity measurement) where obtained from field monitoring. This approach demonstrates an association between the spatial distribution of erosive features with high values of soil saturation, and reduced water discharge (10-110 cm3/s), that are consistent with the lower values of electrical resistivity. The areas with the highest amount of erosive features are related to medium sediment flux values, (13.8-334.2 g/ms), medium or high transport capacity (250.3g/ms - 9.4 kg/ms), and sediment concentration with medium or very high classes where register more than 70% of gullies. These values, combined with low hydraulic conductivity with average Ks values 0.0004 cm3/s, and soil infiltration capacity with values from 0.11 to 0.36 cm/min, derives from the fine texture of soils - gravel (18.8 - 47.9%), sand (10.8 - 20.5%) and silt/clay (32.1 - 64.9%), induce an increased runoff and the development of linear erosion. The obtained results seem to indicate a good performance of the SIMWE model in the identification of the areas more susceptible to the hydric erosion of the soils, indeed, the most critical areas show the connection between the inventoried erosive forms. Keywords: Water Erosion, SIMWE, Agricultural Terraces, Alto Douro Wine Region References Mitas, H. e Mitasova, L. (1998). Distribuited Soil Erosion Simulation for effective erosion prevention. Water Resources Research, Vol. 34(3), pp. 505-516.

Characteristics of pulsed runoff-erosion events under typical rainstorms in a small watershed on the Loess Plateau of China.

PubMed

Wu, Lei; Jiang, Jun; Li, Gou-Xia; Ma, Xiao-Yi

2018-02-27

The pulsed events of rainstorm erosion on the Loess Plateau are well-known, but little information is available concerning the characteristics of superficial soil erosion processes caused by heavy rainstorms at the watershed scale. This study statistically evaluated characteristics of pulsed runoff-erosion events based on 17 observed rainstorms from 1997-2010 in a small loess watershed on the Loess Plateau of China. Results show that: 1) Rainfall is the fundamental driving force of soil erosion on hillslopes, but the correlations of rainfall-runoff and rainfall-sediment in different rainstorms are often scattered due to infiltration-excess runoff and soil conservation measures. 2) Relationships between runoff and sediment for each rainstorm event can be regressed by linear, power, logarithmic and exponential functions. Cluster Analysis is helpful in classifying runoff-erosion events and formulating soil conservation strategies for rainstorm erosion. 3) Response characteristics of sediment yield are different in different levels of pulsed runoff-erosion events. Affected by rainfall intensity and duration, large changes may occur in the interactions between flow and sediment for different flood events. Results provide new insights into runoff-erosion processes and will assist soil conservation planning in the loess hilly region.

Characterization of solid particle erosion resistance of ductile metals based on their properties

NASA Technical Reports Server (NTRS)

Rao, P. V.; Buckley, D. H.

1985-01-01

This paper presents experimental results pertaining to spherical glass bead and angular crushed glass particle impingement. A concept of energy absorption to explain the failure of material is proposed and is correlated with the erosion characteristics of several pure metals. Analyses of extensive erosion data indicate that the properties - surface energy, specific melting energy, strain energy, melting point, bulk modulus, hardness, atomic volume - and the product of the parameters - linear coefficient of thermal expansion x bulk modulus x temperature rise required for melting, and ultimate resilience x hardness - exhibit the best correlations. The properties of surface energy and atomic volume are suggested for the first time for correlation purposes and are found to correlate well with erosion rates at different angles of impingement. It further appears that both energy and thermal properties contribute to the total erosion.

Modeling runoff and erosion risk in a~small steep cultivated watershed using different data sources: from on-site measurements to farmers' perceptions

NASA Astrophysics Data System (ADS)

Auvet, B.; Lidon, B.; Kartiwa, B.; Le Bissonnais, Y.; Poussin, J.-C.

2015-09-01

This paper presents an approach to model runoff and erosion risk in a context of data scarcity, whereas the majority of available models require large quantities of physical data that are frequently not accessible. To overcome this problem, our approach uses different sources of data, particularly on agricultural practices (tillage and land cover) and farmers' perceptions of runoff and erosion. The model was developed on a small (5 ha) cultivated watershed characterized by extreme conditions (slopes of up to 55 %, extreme rainfall events) on the Merapi volcano in Indonesia. Runoff was modelled using two versions of STREAM. First, a lumped version was used to determine the global parameters of the watershed. Second, a distributed version used three parameters for the production of runoff (slope, land cover and roughness), a precise DEM, and the position of waterways for runoff distribution. This information was derived from field observations and interviews with farmers. Both surface runoff models accurately reproduced runoff at the outlet. However, the distributed model (Nash-Sutcliffe = 0.94) was more accurate than the adjusted lumped model (N-S = 0.85), especially for the smallest and biggest runoff events, and produced accurate spatial distribution of runoff production and concentration. Different types of erosion processes (landslides, linear inter-ridge erosion, linear erosion in main waterways) were modelled as a combination of a hazard map (the spatial distribution of runoff/infiltration volume provided by the distributed model), and a susceptibility map combining slope, land cover and tillage, derived from in situ observations and interviews with farmers. Each erosion risk map gives a spatial representation of the different erosion processes including risk intensities and frequencies that were validated by the farmers and by in situ observations. Maps of erosion risk confirmed the impact of the concentration of runoff, the high susceptibility of long steep slopes, and revealed the critical role of tillage direction. Calibrating and validating models using in situ measurements, observations and farmers' perceptions made it possible to represent runoff and erosion risk despite the initial scarcity of hydrological data. Even if the models mainly provided orders of magnitude and qualitative information, they significantly improved our understanding of the watershed dynamics. In addition, the information produced by such models is easy for farmers to use to manage runoff and erosion by using appropriate agricultural practices.

Erosion-corrosion and cavitation-erosion measurements on copper alloys utilizing thin layer activation technique

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tsai, C.H.; Hsu, K.Y.; Kai, J.J.

1992-12-31

The surface layers of copper alloy specimens were made radioactive by bombarding with 5 MeV protons from a van de Graaff accelerator which converted Cu-65 into Zn-65 through (p,n) reaction. The amount of surface material loss could then be monitored by measuring the total remaining {gamma}-ray activity generated from Zn-65 decay. This technique, termed thin layer activation (TLA), has the advantage of in situ monitoring the rate of surface removal due to corrosion, erosion-corrosion, wearing, etc. In this work, the erosion-corrosion tests on aluminum brass and 90Cu-10Ni were conducted in circulating sea water and the erosion-corrosion rates measured using TLAmore » and conventional methods such as linear polarization resistance (LPR) method and weight loss coupons were compared. A vibrational cavitation-erosion test was also performed on aluminum bronze, in which the measurements by TLA were compared with those of weight loss measurements.« less

Rainfall-induced soil aggregate breakdown in field experiments at different rainfall intensities and initial soil moisture conditions

NASA Astrophysics Data System (ADS)

Shi, Pu; Thorlacius, Sigurdur; Keller, Thomas; Keller, Martin; Schulin, Rainer

2017-04-01

Soil aggregate breakdown under rainfall impact is an important process in interrill erosion, but is not represented explicitly in water erosion models. Aggregate breakdown not only reduces infiltration through surface sealing during rainfall, but also determines the size distribution of the disintegrated fragments and thus their availability for size-selective sediment transport and re-deposition. An adequate representation of the temporal evolution of fragment mass size distribution (FSD) during rainfall events and the dependence of this dynamics on factors such as rainfall intensity and soil moisture content may help improve mechanistic erosion models. Yet, little is known about the role of those factors in the dynamics of aggregate breakdown under field conditions. In this study, we conducted a series of artificial rainfall experiments on a field silt loam soil to investigate aggregate breakdown dynamics at different rainfall intensity (RI) and initial soil water content (IWC). We found that the evolution of FSD in the course of a rainfall event followed a consistent two-stage pattern in all treatments. The fragment mean weight diameter (MWD) drastically decreased in an approximately exponential way at the beginning of a rainfall event, followed by a further slow linear decrease in the second stage. We proposed an empirical model that describes this temporal pattern of MWD decrease during a rainfall event and accounts for the effects of RI and IWC on the rate parameters. The model was successfully tested using an independent dataset, showing its potential to be used in erosion models for the prediction of aggregate breakdown. The FSD at the end of the experimental rainfall events differed significantly among treatments, indicating that different aggregate breakdown mechanisms responded differently to the variation in initial soil moisture and rainfall intensity. These results provide evidence that aggregate breakdown dynamics needs to be considered in a case-specific manner in modelling sediment mobilization and transport during water erosion events.

Spatial distribution of loggerhead turtle (Caretta caretta) emergences along a highly dynamic beach in the northern Gulf of Mexico

USGS Publications Warehouse

Lamont, Margaret M.; Houser, Chris

2014-01-01

As coastlines change due to sea level rise and an increasing human presence, understanding how species, such as marine turtles, respond to alterations in habitat is necessary for proper management and conservation. Survey data from a major nesting beach in the northern Gulf of Mexico, where a revetment was installed, was used to assess spatial distribution of loggerhead emergences. Through use of Quadrat analysis and piecewise linear regression with breakpoint, we present evidence to suggest that nest site selection in loggerheads is determined in the nearshore environment, and by characteristics such as wave height, alongshore currents, depth and patterns of erosion and accretion. Areas of relatively dense nesting were found in areas with relatively strong alongshore currents, relatively small waves, a steep offshore slope and the largest historical rates of erosion. Areas of relatively dense nesting also corresponded to areas of low nesting success. Both nesting and non-nesting emergences were clustered immediately adjacent to the revetment and at other eroding sites along the beach. These results suggest that alterations to the nearshore environment from activities such as construction of a jetty, dredging or installation of pilings, may impact sea turtle nest distribution alongshore. We also show that piecewise linear regression with breakpoint is a technique that can be used with geomorphological and oceanographic data to predict locations of nest clumping and may be useful for managers at other nesting beaches.

Modeling the reduction in soil loss due to soil armouring caused by rainfall erosion

USDA-ARS?s Scientific Manuscript database

Surface soil properties can change as a result of soil disturbances, erosion, or deposition. One process that can significantly change surface soil properties is soil armouring, which is the selective removal of finer particles by rill or interrill erosion, leaving an armoured layer of coarser parti...

Crop Performance and Soil Properties in Two Artificially-Eroded Soils in North-Central Alberta

DOE Office of Scientific and Technical Information (OSTI.GOV)

Izaurralde, R Cesar C.; Malhi, S. S.; Nyborg, M.

2006-09-01

Field experiments were conducted from 1991 to 1995 at Josephburg (Orthic Black Chernozem, Typic Cryoboroll) and Cooking Lake (Orthic Gray Luvisol, Typic Cryoboralf), Alberta, to determine impact of topsoil removal on selected soil properties, N-mineralization potential and crop yield, and effectiveness of various amendments for restoring the productivity of eroded soils. The simulated-erosion levels were established in the autumn of 1990 by removing 20 cm topsoil in 5-cm depth increments. The four amendments were: control, addition of 5 cm of topsoil, fertilizers to supply 100 kg N ha-1 and 20 kg P ha-1, and cattle manure at 75 Mg ha-1.more » Topsoil and manure were applied once in the autumn of 1990, while fertilizers were applied annually from 1991 to 1995. Available N and P, total C, N and P, and N-mineralization potential decreased, while bulk density increased with increasing depth of topsoil removal. Tiller number, plant height, spike density, thousand kernel weight, and leaf area index decreased with simulated erosion. Grain yield reductions due to simulated soil erosion were either linear or curvilinear functions of nutrient removal. Application of N and P fertilizers and manure improved grain yield and reduced the impact of yield loss due to erosion. Return of 5 cm of topsoil also increased grain yield, but to a lesser extent than manure or fertilizers. Grain yields were maximized when fertilizers were also applied to organic amendment treatments. In conclusion, the findings suggest the importance of integrated use of organic amendments and chemical fertilizers for best crop yields on severely-eroded soils.« less

Relationship between water quality and macro-scale parameters (land use, erosion, geology, and population density) in the Siminehrood River Basin.

PubMed

Bostanmaneshrad, Farshid; Partani, Sadegh; Noori, Roohollah; Nachtnebel, Hans-Peter; Berndtsson, Ronny; Adamowski, Jan Franklin

2018-10-15

To date, few studies have investigated the simultaneous effects of macro-scale parameters (MSPs) such as land use, population density, geology, and erosion layers on micro-scale water quality variables (MSWQVs). This research focused on an evaluation of the relationship between MSPs and MSWQVs in the Siminehrood River Basin, Iran. In addition, we investigated the importance of water particle travel time (hydrological distance) on this relationship. The MSWQVs included 13 physicochemical and biochemical parameters observed at 15 stations during three seasons. Primary screening was performed by utilizing three multivariate statistical analyses (Pearson's correlation, cluster and discriminant analyses) in seven series of observed data. These series included three separate seasonal data, three two-season data, and aggregated three-season data for investigation of relationships between MSPs and MSWQVs. Coupled data (pairs of MSWQVs and MSPs) repeated in at least two out of three statistical analyses were selected for final screening. The primary screening results demonstrated significant relationships between land use and phosphorus, total solids and turbidity, erosion levels and electrical conductivity, and erosion and total solids. Furthermore, water particle travel time effects were considered through three geographical pattern definitions of distance for each MSP by using two weighting methods. To find effective MSP factors on MSWQVs, a multivariate linear regression analysis was employed. Then, preliminary equations that estimated MSWQVs were developed. The preliminary equations were modified to adaptive equations to obtain the final models. The final models indicated that a new metric, referred to as hydrological distance, provided better MSWQV estimation and water quality prediction compared to the National Sanitation Foundation Water Quality Index. Crown Copyright © 2018. Published by Elsevier B.V. All rights reserved.

Soil water erosion processes in mountain forest catchment - analysis by using terrestrial laser scanning

NASA Astrophysics Data System (ADS)

Dąbek, Paweł; Żmuda, Romuald; Szczepański, Jakub; Ćmielewski, Bartłomiej; Patrzałek, Ciechosław

2013-04-01

The paper presents the results of the analysis of the water erosion processes of soil occurring in forestry mountain catchment area in the region of West Sudetes Mountain in Poland. The research was carried out within the experimental area of skid trails (operational trails), which were used to the end of 2010 in obtaining wood and its mechanical transport to the place of storage. As a consequence of forestry works that were carried out it was changing the natural structure of ground and its surface on the wooded slopes, which, combined with the favorable hydro-meteorological conditions contributed to the intensification of the water erosion processes of soil on surface of trails. For the implementation of the research project of the analysis of water erosion processes in the forestry catchment area innovative was used terrestrial laser scanning. Using terrestrial laser scanning has enabled the analysis of the dynamics of erosion processes both in time, as well as in spatial and quantitative terms. Scanning was performed at a resolution of 4 mm, resulting in 62 500 points per 1 square meter. After filtering the data were interpolated to other resolution of 1 cm, which can identify even the smallest linear and surface effects of erosion. While installed on the experimental area, along the skid trails, anti-erosion barriers in order to reduce transport eroded material and allow its accumulation. Allowed to precisely determine the location of areas of accumulation, the rate and amount of accumulated material. The result of the analyses that was carried out is identification areas of denudation of the eroded material, and also determine the intensity of the erosion processes and their quantitative analysis. The long-term researches on hydrological conditions and forest complexes functioning show that forest effectively stores water, limits linear and surface flow and delays water outflow from a catchment. Carried out a research project using the terrestrial laser scanning shows that anthropogenic activities in the form of forest management and their effects in the form of dense network of forest roads and skid trails and obtaining wood diminish correct functioning of a forest or even increase the phenomenon of erosion. Submit the results of the analysis consider the problem of dynamics and intensity of erosion processes in mountain areas, and show the effectiveness of the methodology of research.

Quantifying recent erosion and sediment delivery using probability sampling: A case study

Treesearch

Jack Lewis

2002-01-01

Abstract - Estimates of erosion and sediment delivery have often relied on measurements from locations that were selected to be representative of particular terrain types. Such judgement samples are likely to overestimate or underestimate the mean of the quantity of interest. Probability sampling can eliminate the bias due to sample selection, and it permits the...

Dimensionless erosion laws for cohesive sediment

USGS Publications Warehouse

Walder, Joseph S.

2016-01-01

A method of achieving a dimensionless collapse of erosion-rate data for cohesive sediments is proposed and shown to work well for data collected in flume-erosion tests on mixtures of sand and mud (silt plus clay sized particles) for a wide range of mud fraction. The data collapse corresponds to a dimensional erosion law of the form E∼(τ−τc)m">E∼(τ−τc)mE∼(τ−τc)m, where E">EE is erosion rate, τ">ττ is shear stress, τc">τcτc is the threshold shear stress for erosion to occur, and m≈7/4">m≈7/4m≈7/4. This result contrasts with the commonly assumed linear erosion law E=kd(τ−τc)">E=kd(τ−τc)E=kd(τ−τc), where kd">kdkd is a measure of how easily sediment is eroded. The data collapse prompts a re-examination of the way that results of the hole-erosion test (HET) and jet-erosion test (JET) are customarily analyzed, and also calls into question the meaningfulness not only of proposed empirical relationships between kd">kdkd and τc">τcτc, but also of the erodibility parameter kd">kdkd itself. Fuller comparison of flume-erosion data with hole-erosion and jet-erosion data will require revised analyses of the HET and JET that drop the assumption m=1">m=1m=1 and, in the case of the JET, certain simplifying assumptions about the mechanics of jet scour.

Nutrient and dust enrichment in Danish wind erosion sediments for different tillage directions

NASA Astrophysics Data System (ADS)

Mohammadian Behbahani, Ali; Fister, Wolfgang; Heckrath, Goswin; Kuhn, Nikolaus J.

2015-04-01

More than 80% of the soil types in Denmark have a sandy texture. Denmark is also subject to strong offshore and onshore winds, therefore, Danish soils are considered especially vulnerable to wind erosion. Where conventional tillage operations are applied on poorly aggregated soils, tillage ridges are more or less the only roughness element that can be used to protect soils against wind erosion until crop plants are large enough to provide sufficient breaks. Since wind erosion is a selective process, it can be assumed that increasing erosion rates are associated with increasing loss of dust sized particles and nutrients. However, selective erosion is strongly affected by the orientation and respective trapping efficiency of tillage ridges and furrows. The main objective of this study, therefore, was to determine the effect of tillage direction on nutrient mobilization by wind erosion from agricultural land in Denmark. In order to assess the relationship between the enrichment ratio of specific particle sizes and the amount of eroded nutrients, three soils with loamy sand texture, but varying amounts of sand-sized particles, were selected. In addition, a soil with slightly less sand, but much higher organic matter content was chosen. The soils were tested with three different soil surface scenarios (flat surface, parallel tillage, perpendicular tillage) in a wind tunnel simulation. The parallel tillage operation experienced the greatest erosion rates, independent of soil type. Particles with D50 between 100-155 µm showed the greatest risk of erosion. However, due to a greater loss of dust sized particles from perpendicularly tilled surfaces, this wind-surface arrangement showed a significant increase in nutrient enrichment ratio compared to parallel tillage and flat surfaces. The main reason for this phenomenon is most probably the trapping of larger particles in the perpendicular furrows. This indicates that the highest rate of soil protection does not necessarily coincide with lowest soil nutrient losses and dust emissions. For the evaluation of protection measures on these soil types in Denmark it is, therefore, important to differentiate between their effectivity to reduce total soil erosion amount, dust emission, and nutrient loss.

Liquid metals as a divertor plasma-facing material explored using the Pilot-PSI and Magnum-PSI linear devices

NASA Astrophysics Data System (ADS)

Morgan, T. W.; Rindt, P.; van Eden, G. G.; Kvon, V.; Jaworksi, M. A.; Lopes Cardozo, N. J.

2018-01-01

For DEMO and beyond, liquid metal plasma-facing components are considered due to their resilience to erosion through flowed replacement, potential for cooling beyond conduction and inherent immunity to many of the issues of neutron loading compared to solid materials. The development curve of liquid metals is behind that of e.g. tungsten however, and tokamak-based research is currently somewhat limited in scope. Therefore, investigation into linear plasma devices can provide faster progress under controlled and well-diagnosed conditions in assessing many of the issues surrounding the use of liquid metals. The linear plasma devices Magnum-PSI and Pilot-PSI are capable of producing DEMO-relevant plasma fluxes, which well replicate expected divertor conditions, and the exploration of physics issues for tin (Sn) and lithium (Li) such as vapour shielding, erosion under high particle flux loading and overall power handling are reviewed here. A deeper understanding of erosion and deposition through this work indicates that stannane formation may play an important role in enhancing Sn erosion, while on the other hand the strong hydrogen isotope affinity reduces the evaporation rate and sputtering yields for Li. In combination with the strong redeposition rates, which have been observed under this type of high-density plasma, this implies that an increase in the operational temperature range, implying a power handling range of 20-25 MW m-2 for Sn and up to 12.5 MW m-2 for Li could be achieved. Vapour shielding may be expected to act as a self-protection mechanism in reducing the heat load to the substrate for off-normal events in the case of Sn, but may potentially be a continual mode of operation for Li.

Monthly Rainfall Erosivity Assessment for Switzerland

NASA Astrophysics Data System (ADS)

Schmidt, Simon; Meusburger, Katrin; Alewell, Christine

2016-04-01

Water erosion is crucially controlled by rainfall erosivity, which is quantified out of the kinetic energy of raindrop impact and associated surface runoff. Rainfall erosivity is often expressed as the R-factor in soil erosion risk models like the Universal Soil Loss Equation (USLE) and its revised version (RUSLE). Just like precipitation, the rainfall erosivity of Switzerland has a characteristic seasonal dynamic throughout the year. This inter-annual variability is to be assessed by a monthly and seasonal modelling approach. We used a network of 86 precipitation gauging stations with a 10-minute temporal resolution to calculate long-term average monthly R-factors. Stepwise regression and Monte Carlo Cross Validation (MCCV) was used to select spatial covariates to explain the spatial pattern of R-factor for each month across Switzerland. The regionalized monthly R-factor is mapped by its individual regression equation and the ordinary kriging interpolation of its residuals (Regression-Kriging). As covariates, a variety of precipitation indicator data has been included like snow height, a combination of hourly gauging measurements and radar observations (CombiPrecip), mean monthly alpine precipitation (EURO4M-APGD) and monthly precipitation sums (Rhires). Topographic parameters were also significant explanatory variables for single months. The comparison of all 12 monthly rainfall erosivity maps showed seasonality with highest rainfall erosivity in summer (June, July, and August) and lowest rainfall erosivity in winter months. Besides the inter-annual temporal regime, a seasonal spatial variability was detectable. Spatial maps of monthly rainfall erosivity are presented for the first time for Switzerland. The assessment of the spatial and temporal dynamic behaviour of the R-factor is valuable for the identification of more susceptible seasons and regions as well as for the application of selective erosion control measures. A combination with monthly vegetation cover (C-factor) maps would enable the assessment of seasonal dynamics of erosion processes in Switzerland.

An Assessment of the Impact of Urbanization on Soil Erosion in Inner Mongolia.

PubMed

Wang, Li-Yan; Xiao, Yi; Rao, En-Ming; Jiang, Ling; Xiao, Yang; Ouyang, Zhi-Yun

2018-03-19

Inner Mongolia, an autonomous region of the People's Republic of China, has experienced severe soil erosion following a period of rapid economic development and urbanization. To investigate how urbanization has influenced the extent of soil erosion in Inner Mongolia, we used urbanization and soil erosion data from 2000 through 2010 to determine the relationship between urbanization and soil erosion patterns. Two empirical equations-the Revised Universal Soil Loss Equation (RUSLE) and the Revised Wind Erosion Equation (RWEQ)-were used to estimate the intensity of soil erosion, and we performed backward linear regression to model how it changed with greater urbanization. There was an apparent increase in the rate of urbanization and a decrease in the area affected by soil erosion in 2010 compared to the corresponding values for 2000. The urban population stood at 11.32 million in 2010, which represented a 16.47% increase over that in 2000. The area affected by soil erosion in 2000 totaled 704,817 km², yet it had decreased to 674,135 km² by 2010. However, a path of modest urban development (rural-urban mitigation) and reasonable industrial structuring (the development of GDP-2) may partially reduce urbanization's ecological pressure and thus indirectly reduce the threat of soil erosion to human security. Therefore, to better control soil erosion in Inner Mongolia during the process of urbanization, the current model of economic development should be modified to improve the eco-efficiency of urbanization, while also promoting new modes of urbanization that are environmentally sustainable, cost-effective, and conserve limited resources.

An Assessment of the Impact of Urbanization on Soil Erosion in Inner Mongolia

PubMed Central

Xiao, Yi; Rao, En-Ming; Jiang, Ling; Xiao, Yang; Ouyang, Zhi-Yun

2018-01-01

Inner Mongolia, an autonomous region of the People’s Republic of China, has experienced severe soil erosion following a period of rapid economic development and urbanization. To investigate how urbanization has influenced the extent of soil erosion in Inner Mongolia, we used urbanization and soil erosion data from 2000 through 2010 to determine the relationship between urbanization and soil erosion patterns. Two empirical equations—the Revised Universal Soil Loss Equation (RUSLE) and the Revised Wind Erosion Equation (RWEQ)—were used to estimate the intensity of soil erosion, and we performed backward linear regression to model how it changed with greater urbanization. There was an apparent increase in the rate of urbanization and a decrease in the area affected by soil erosion in 2010 compared to the corresponding values for 2000. The urban population stood at 11.32 million in 2010, which represented a 16.47% increase over that in 2000. The area affected by soil erosion in 2000 totaled 704,817 km2, yet it had decreased to 674,135 km2 by 2010. However, a path of modest urban development (rural–urban mitigation) and reasonable industrial structuring (the development of GDP-2) may partially reduce urbanization’s ecological pressure and thus indirectly reduce the threat of soil erosion to human security. Therefore, to better control soil erosion in Inner Mongolia during the process of urbanization, the current model of economic development should be modified to improve the eco-efficiency of urbanization, while also promoting new modes of urbanization that are environmentally sustainable, cost-effective, and conserve limited resources. PMID:29562707

Erosion and re-deposition of lithium and boron coatings under high-flux plasma bombardment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Abrams, Tyler Wayne

2015-01-01

Lithium and boron coatings are applied to the walls of many tokamaks to enhance performance and protect the underlying substrates. Li and B-coated high-Z substrates are planned for use in NSTX-U and are a candidate plasma-facing component (PFC) for DEMO. However, previous measurements of Li evaporation and thermal sputtering on low-flux devices indicate that the Li temperature permitted on such devices may be unacceptably low. Thus it is crucial to characterize gross and net Li erosion rates under high-flux plasma bombardment. Additionally, no quantitative measurements have been performed of the erosion rate of a boron-coated PFC during plasma bombardment. Amore » realistic model for the compositional evolution of a Li layer under D bombardment was developed that incorporates adsorption, implantation, and diffusion. A model was developed for temperature-dependent mixed-material Li-D erosion that includes evaporation, physical sputtering, chemical sputtering, preferential sputtering, and thermal sputtering. The re-deposition fraction of a Li coating intersecting a linear plasma column was predicted using atomic physics information and by solving the Li continuity equation. These models were tested in the Magnum-PSI linear plasma device at ion fluxes of 10^23-10^24 m^-2 s^-1 and Li surface temperatures less than 800 degrees C. Li erosion was measured during bombardment with a neon plasma that will not chemically react with Li and the results agreed well with the erosion model. Next the ratio of the total D fluence to the areal density of the Li coating was varied to quantify differences in Li erosion under D plasma bombardment as a function of the D concentration. The ratio of D/Li atoms was calculated using the results of MD simulations and good agreement is observed between measurements and the predictions of the mixed-material erosion model. Li coatings are observed to disappear from graphite much faster than from TZM Mo, indicating that fast Li diffusion into the bulk graphite substrate occurred, as predicted. Li re-deposition fractions very close to unity are observed in Magnum-PSI, as predicted by modeling. Finally, predictions of Li coating lifetimes in the NSTX-U divertor are calculated. The gross erosion rate of boron coatings was also measured for the first time in a high-flux plasma device.« less

Evaluation of the sustainability of road drainage systems

NASA Astrophysics Data System (ADS)

García-Diez, Iván; Palencia, Covadonga; Fernández Raga, María

2017-04-01

Water is the most erosive agent that exists on the linear structures, because they are constantly subjected to outdoor condition like irregular infiltration, frosts and different rain intensities. Another variables that highly influence in the entire lifetime of a natural drainage system are the spatial and temporal variability of the rainfall, the soil, the vegetation cover and the design. All this factors are affecting the vulnerability of the clearings and embankments, by wearing away the weakest materials which surround the roads or train rails, producing erosion and very bumpy surfaces. The result is that the original pattern, developped to disminished the lost of soil, is not properly working and it cannot eliminate water, with the consequence destruction of the linear structure after several rainfall periods, and the accumulation of material down slope. The propose of this research focuses on analysing the drainage systems used in spanish roads and railways lines. For this purpose, a revision of the literature has been done, and the main drainage solutions have been recovered, carrying out an evaluation of them from an environmental point of view. This procedure has been requested by several authors in the past (Nwa, E.U. & Twocock, J.G., 1969; Goulter, I.C., 1992), together with the need of designing a more sustainable drainage system. The final objective of this complete revision is to compare objetively the designs to valuate them in order to develop a new drainage patter which minimize the erosion, increasing the durability and effectiveness of the drainage system. For this purpose, it is neccesary to assure that all the systems will be compare under similar parameters of flow rate, vegetation, substrate, lenght, slope and total section. Only the channels pattern and water distribution will change. The analysis has been done following Liu, H. & Zhu, X.B., (2012), who pointed out that the main parameters to take into account to select a road drainage system are the hydraulic functioning, structural strength, produced erosion, service life, initial invesment and maintenance costs of different drainage systems. The followed methodology was to create a Leopold's matrix to compare among the alternatives of drainage design, asignating a puntuation from 1 to 5 to each factor that affects the functioning of the drainage. The process to decide the punctuation of every factor in each drainage design will be also explained. The alternative which obtains more puntuation represents the best available design to decrease erosion on the slopes and increase the service life. The validation of this results has been done in the field. References Goulter, I.C., 1992. Systems Analysis in Water-Distribution Network Design: From Theory to Practice, Journal of Water Resources Planning and Management. ASCE 118, No. 3 Nwa, E.U. & Twocock, J.G., 1969. Drainage design theory and practice. Journal of Hydrology 9, 259-276 Liu, H. & Zhu, X.B., 2012. Influencing Factors and Prevention Measures of Erosion Damage for Highway Slope in Loess Area. Advanced Materials Research 594, 161-166

In-Situ Measurement of Hall Thruster Erosion Using a Fiber Optic Regression Probe

NASA Technical Reports Server (NTRS)

Polzink, Kurt A.; Korman, Valentin

2008-01-01

One potential life-limiting mechanism in a Hall thruster is the erosion of the ceramic material comprising the discharge channel. This is especially true for missions that require long thrusting periods and can be problematic for lifetime qualification, especially when attempting to qualify a thruster by analysis rather than a test lasting the full duration of the mission. In addition to lifetime, several analytical and numerical models include electrode erosion as a mechanism contributing to enhanced transport properties. However, there is still a great deal of dispute over the importance of erosion to transport in Hall thrusters. The capability to perform an in-situ measurement of discharge channel erosion is useful in addressing both the lifetime and transport concerns. An in-situ measurement would allow for real-time data regarding the erosion rates at different operating points, providing a quick method for empirically anchoring any analysis geared towards lifetime qualification. Erosion rate data over a thruster's operating envelope would also be useful in the modeling of the detailed physics inside the discharge chamber. A recent fundamental sensor development effort has led to a novel regression, erosion, and ablation sensor technology (REAST). The REAST sensor allows for measurement of real-time surface erosion rates at a discrete surface location. The sensor was tested using a linear Hall thruster geometry, which served as a means of producing plasma erosion of a ceramic discharge chamber. The mass flow rate, discharge voltage, and applied magnetic field strength could be varied, allowing for erosion measurements over a broad thruster operating envelope. Results are presented demonstrating the ability of the REAST sensor to capture not only the insulator erosion rates but also changes in these rates as a function of the discharge parameters.

A new methodology for hydro-abrasive erosion tests simulating penstock erosive flow

NASA Astrophysics Data System (ADS)

Aumelas, V.; Maj, G.; Le Calvé, P.; Smith, M.; Gambiez, B.; Mourrat, X.

2016-11-01

Hydro-abrasive resistance is an important property requirement for hydroelectric power plant penstock coating systems used by EDF. The selection of durable coating systems requires an experimental characterization of coating performance. This can be achieved by performing accelerated and representative laboratory tests. In case of severe erosion induced by a penstock flow, there is no suitable method or standard representative of real erosive flow conditions. The presented study aims at developing a new methodology and an associated laboratory experimental device. The objective of the laboratory apparatus is to subject coated test specimens to wear conditions similar to the ones generated at the penstock lower generatrix in actual flow conditions. Thirteen preselected coating solutions were first been tested during a 45 hours erosion test. A ranking of the thirteen coating solutions was then determined after characterisation. To complete this first evaluation and to determine the wear kinetic of the four best coating solutions, additional erosion tests were conducted with a longer duration of 216 hours. A comparison of this new method with standardized tests and with real service operating flow conditions is also discussed. To complete the final ranking based on hydro-abrasive erosion tests, some trial tests were carried out on penstock samples to check the application method of selected coating systems. The paper gives some perspectives related to erosion test methodologies for materials and coating solutions for hydraulic applications. The developed test method can also be applied in other fields.

Effects of DEM source and resolution on WEPP hydrologic and erosion simulation: A case study of two forest watersheds in northern Idaho

Treesearch

J. X. Zhang; J. Q. Wu; K. Chang; W. J. Elliot; S. Dun

2009-01-01

The recent modification of the Water Erosion Prediction Project (WEPP) model has improved its applicability to hydrology and erosion modeling in forest watersheds. To generate reliable topographic and hydrologic inputs for the WEPP model, carefully selecting digital elevation models (DEMs) with appropriate resolution and accuracy is essential because topography is a...

Mariner 9 evidence for wind erosion in the equatorial and mid-latitude regions of Mars

NASA Technical Reports Server (NTRS)

Mccauley, J. F.

1973-01-01

Evidence for extensive wind erosion principally in the equatorial and mid-latitude regions of Mars is presented and compared with selected erosional landforms from the coastal desert of Peru known to be of eolian origin. The evidence for widespread erosion on Mars prompted an examination of certain aspects of its wind regime that are thought to be significant geologically.

Dust and nutrient enrichment by wind erosion from Danish soils in dependence of tillage direction

NASA Astrophysics Data System (ADS)

Mohammadian Behbahani, Ali; Fister, Wolfgang; Heckrath, Goswin; Kuhn, Nikolaus J.

2016-04-01

Wind erosion is a selective process, which promotes erosion of fine particles. Therefore, it can be assumed that increasing erosion rates are generally associated with increasing loss of dust sized particles and nutrients. However, this selective process is strongly affected by the orientation and respective trapping efficiency of tillage ridges and furrows. Since tillage ridges are often the only protection measure available on poorly aggregated soils in absence of a protective vegetation cover, it is very important to know which orientation respective to the dominant wind direction provides best protection. This knowledge could be very helpful for planning erosion protection measures on fields with high wind erosion susceptibility. The main objective of this study, therefore, was to determine the effect of tillage direction on dust and nutrient mobilization by wind, using wind tunnel simulations. In order to assess the relationship between the enrichment ratio of specific particle sizes and the amount of eroded nutrients, three soils with loamy sand texture, but varying amounts of sand-sized particles, were selected. In addition, a soil with slightly less sand, but much higher organic matter content was chosen. The soils were tested with three different soil surface scenarios - flat surface, parallel tillage, perpendicular tillage. The parallel tillage operation experienced the greatest erosion rates, independent of soil type. Particles with D50 between 100-155 μm showed the greatest risk of erosion. However, due to a greater loss of dust sized particles from perpendicularly tilled surfaces, this wind-surface arrangement showed a significant increase in nutrient enrichment ratio compared to parallel tillage and flat surfaces. The main reason for this phenomenon is most probably the trapping of larger particles in the perpendicular furrows. This indicates that the highest rate of soil protection does not necessarily coincide with lowest soil nutrient losses and dust emissions. For the evaluation of protection measures on these soil types in Denmark it is, therefore, important to differentiate between their effectivity to reduce total soil erosion amount, dust emission, and nutrient loss.

Interrill Erodibility of P and C on conventially and organically farmed Devon soils

NASA Astrophysics Data System (ADS)

Kuhn, N. J.

2012-04-01

Soil erosion can have significant off-site effects on water quality and thus human and habitat health. Apart from sedimentation, the transfer of nutrients, both dissolved and particulate, is a major concern. The particulate transfer of nutrients from agricultural land can occur either by rill or interrill erosion. Rill erosion is non-selective and affects only a limited extent of agricultural land. Interrill processes such as crusting, splash and raindrop-impacted wash, on the other hand, act on all cropland and affect the quality of the water from all areas generating runoff. A significant amount of phosphorus (P) is contained in the surface soil layer transformed by interrill processes annually. In the EU, the P content of a crusted (2 mm) surface layer corresponds to 4 to 40 kg ha-1 of P on arable land (1.094 mil km2). Therefore, the role of interrill processes and erosion for regional nutrient cycling requires close attention. Interrill erosion is a complex phenomenon, involving the detachment, transport and deposition of soil particles by raindrop impacted flow. Resistance to interrill erosion varies between soils depending on their physical, chemical and mineralogical properties. In addition, significant changes in soil resistance to interrill erosion occur during storms as a result of changes in surface roughness, cohesion and particle size. As a consequence, erosion on interrill areas is selective, moving the most easily detached small and/or light soil particles which are often enriched in clay, P and organic C. Commonly, the risk of erosion associated with organically farmed soils is lower than those farmed in a conventional way. This is attributed to greater aggregate stability and thus greater infiltration and lower erodibility. Erosion of nutrients on organically farmed soils is therefore considered to be reduced by the same order of magnitude than the amount of eroded soil compared to conventionally farmed soils. However, the selective nature of interrill erosion potentially counteracts this effect by the preferential removal of fine particles enriched in nutrients and soil organic matter. In this study, an experiment comparing the erodibility of P and C on organically and conventially farmed soils from Devon is presented. The results show a disproportional increase of P in sediment from the organically farmed soil, reducing the perceived benefit of organic farming on nutrient erosion by 80%. The pronounced P enrichment in the organically farmed soil is attributed to the higher concentrations of C and P as well as lower densities of the small particle fraction. The results, while very preliminary, indicate that the impact of soil management on off-site effects of erosion such as water quality can only be fully assessed when we understand the relevant erosion processes. They also indicate that some less than expected positive effects of changing soil management to improve water quality might be caused by the preferential erosion of P-bearing soil particles.

Assessing soil quality indicator under different land use and soil erosion using multivariate statistical techniques.

PubMed

Nosrati, Kazem

2013-04-01

Soil degradation associated with soil erosion and land use is a critical problem in Iran and there is little or insufficient scientific information in assessing soil quality indicator. In this study, factor analysis (FA) and discriminant analysis (DA) were used to identify the most sensitive indicators of soil quality for evaluating land use and soil erosion within the Hiv catchment in Iran and subsequently compare soil quality assessment using expert opinion based on soil surface factors (SSF) form of Bureau of Land Management (BLM) method. Therefore, 19 soil physical, chemical, and biochemical properties were measured from 56 different sampling sites covering three land use/soil erosion categories (rangeland/surface erosion, orchard/surface erosion, and rangeland/stream bank erosion). FA identified four factors that explained for 82 % of the variation in soil properties. Three factors showed significant differences among the three land use/soil erosion categories. The results indicated that based upon backward-mode DA, dehydrogenase, silt, and manganese allowed more than 80 % of the samples to be correctly assigned to their land use and erosional status. Canonical scores of discriminant functions were significantly correlated to the six soil surface indices derived of BLM method. Stepwise linear regression revealed that soil surface indices: soil movement, surface litter, pedestalling, and sum of SSF were also positively related to the dehydrogenase and silt. This suggests that dehydrogenase and silt are most sensitive to land use and soil erosion.

Soil erosion under multiple time-varying rainfall events

NASA Astrophysics Data System (ADS)

Heng, B. C. Peter; Barry, D. Andrew; Jomaa, Seifeddine; Sander, Graham C.

2010-05-01

Soil erosion is a function of many factors and process interactions. An erosion event produces changes in surface soil properties such as texture and hydraulic conductivity. These changes in turn alter the erosion response to subsequent events. Laboratory-scale soil erosion studies have typically focused on single independent rainfall events with constant rainfall intensities. This study investigates the effect of multiple time-varying rainfall events on soil erosion using the EPFL erosion flume. The rainfall simulator comprises ten Veejet nozzles mounted on oscillating bars 3 m above a 6 m × 2 m flume. Spray from the nozzles is applied onto the soil surface in sweeps; rainfall intensity is thus controlled by varying the sweeping frequency. Freshly-prepared soil with a uniform slope was subjected to five rainfall events at daily intervals. In each 3-h event, rainfall intensity was ramped up linearly to a maximum of 60 mm/h and then stepped down to zero. Runoff samples were collected and analysed for particle size distribution (PSD) as well as total sediment concentration. We investigate whether there is a hysteretic relationship between sediment concentration and discharge within each event and how this relationship changes from event to event. Trends in the PSD of the eroded sediment are discussed and correlated with changes in sediment concentration. Close-up imagery of the soil surface following each event highlight changes in surface soil structure with time. This study enhances our understanding of erosion processes in the field, with corresponding implications for soil erosion modelling.

The mechanism of erosion of metallic materials under cavitation attack

NASA Technical Reports Server (NTRS)

Rao, B. C. S.; Buckley, D. H.

1985-01-01

The mean depth of penetration rates (MDPRs) of eight polycrystalline metallic materials, Al 6061-T6, Cu, brass, phosphor bronze, Ni, Fe, Mo, and Ti-5Al-2.5Sn exposed to cavitation attack in a viscous mineral oil with a 20 kHz ultrasonic oscillator vibrating at 50 micron amplitude are reported. The titanium alloy followed by molybdenum have large incubation periods and small MDPRs. The incubation periods correlate linearly with the inverse of hardness and the average MDPRs correlate linearly with the inverse of tensile strength of materials. The linear relationships yield better statistical parameters than geometric and exponential relationships. The surface roughness and the ratio of pit depth to pit width (h/a) increase with the duration of cavitation attack. The ratio h/a varies from 0.1 to 0.8 for different materials. Recent investigations (20) using scanning electron microscopy to study deformation and pit formation features are briefly reviewed. Investigations with single crystals indicate that the geometry of pits and erosion are dependent on their orientation.

[Splash erosion of black soil with different reclamation years and its relations to soil aggregates selective characteristics].

PubMed

Zhou, Yi-Yang; Wang, En-Heng; Chen, Xiang-Wei

2009-10-01

Taking the typical black soil with a reclamation history of 8, 30, and 50 years and the un-reclaimed secondary forest land as test objects, a simulation study was made on the process of splash erosion and the selective characteristics of soil aggregates under artificial rainfall condition, with the effects of reclamation on the splash erosion in black soil region analyzed. The splash amount of reclaimed black soil was evidently higher than that of un-reclaimed secondary forest land, and increased with increasing reclamation years, with a variation range of 0.95-7.06 g x cm(-1). There was a significant exponential correlation between splash amount and splash distance, and the percentages of small size water-stable aggregates increased with increasing splash distance. The critical particle size of soil aggregates for the enrichment and depletion of splash erosion was 1.0 mm. Soil water-stable aggregates larger than 2 mm and smaller than 0.25 mm in size and soil organic matter content were the main factors affecting the splash erosion characteristics of typical black soil.

Towards estimates of future rainfall erosivity in Europe based on REDES and WorldClim datasets

NASA Astrophysics Data System (ADS)

Panagos, Panos; Ballabio, Cristiano; Meusburger, Katrin; Spinoni, Jonathan; Alewell, Christine; Borrelli, Pasquale

2017-05-01

The policy requests to develop trends in soil erosion changes can be responded developing modelling scenarios of the two most dynamic factors in soil erosion, i.e. rainfall erosivity and land cover change. The recently developed Rainfall Erosivity Database at European Scale (REDES) and a statistical approach used to spatially interpolate rainfall erosivity data have the potential to become useful knowledge to predict future rainfall erosivity based on climate scenarios. The use of a thorough statistical modelling approach (Gaussian Process Regression), with the selection of the most appropriate covariates (monthly precipitation, temperature datasets and bioclimatic layers), allowed to predict the rainfall erosivity based on climate change scenarios. The mean rainfall erosivity for the European Union and Switzerland is projected to be 857 MJ mm ha-1 h-1 yr-1 till 2050 showing a relative increase of 18% compared to baseline data (2010). The changes are heterogeneous in the European continent depending on the future projections of most erosive months (hot period: April-September). The output results report a pan-European projection of future rainfall erosivity taking into account the uncertainties of the climatic models.

Towards estimates of future rainfall erosivity in Europe based on REDES and WorldClim datasets.

PubMed

Panagos, Panos; Ballabio, Cristiano; Meusburger, Katrin; Spinoni, Jonathan; Alewell, Christine; Borrelli, Pasquale

2017-05-01

The policy requests to develop trends in soil erosion changes can be responded developing modelling scenarios of the two most dynamic factors in soil erosion, i.e. rainfall erosivity and land cover change. The recently developed Rainfall Erosivity Database at European Scale (REDES) and a statistical approach used to spatially interpolate rainfall erosivity data have the potential to become useful knowledge to predict future rainfall erosivity based on climate scenarios. The use of a thorough statistical modelling approach (Gaussian Process Regression), with the selection of the most appropriate covariates (monthly precipitation, temperature datasets and bioclimatic layers), allowed to predict the rainfall erosivity based on climate change scenarios. The mean rainfall erosivity for the European Union and Switzerland is projected to be 857 MJ mm ha -1  h -1  yr -1 till 2050 showing a relative increase of 18% compared to baseline data (2010). The changes are heterogeneous in the European continent depending on the future projections of most erosive months (hot period: April-September). The output results report a pan-European projection of future rainfall erosivity taking into account the uncertainties of the climatic models.

Sports drink consumption and dental erosion among amateur runners.

PubMed

Antunes, Leonardo S; Veiga, Lais; Nery, Victor S; Nery, Caio C; Antunes, Lívia A

2017-01-01

This cross-sectional study assessed the prevalence and potential risk factors for dental erosion in amateur athletes at running events. After a sample calculation, 108 runners from the state of Rio de Janeiro, Brazil, were selected and examined for dental wear by a single trained and calibrated evaluator (kappa = 1.00). To identify risk factors, the runners were interviewed by using a standardized, semi-structured questionnaire. The average (SD) age of the runners was 34.2 (11.45), and the prevalence of dental erosion was 19.4%. Gastroesophageal reflux, running frequency per week, and time expended during competition were associated with dental erosion (P < 0.05). The association between use of isotonic drinks and dental erosion was not significant (P > 0.05). In conclusion, dental erosion was not associated with use of isotonic drinks. However, frequency of exercise per week and gastroesophageal reflux were risk factors for dental erosion.

Rainfall erosivity and sediment load over the Poyang Lake Basin under variable climate and human activities since the 1960s

NASA Astrophysics Data System (ADS)

Gu, Chaojun; Mu, Xingmin; Gao, Peng; Zhao, Guangju; Sun, Wenyi; Yu, Qiang

2018-03-01

Accelerated soil erosion exerts adverse effects on water and soil resources. Rainfall erosivity reflects soil erosion potential driven by rainfall, which is essential for soil erosive risk assessment. This study investigated the spatiotemporal variation of rainfall erosivity and its impacts on sediment load over the largest freshwater lake basin of China (the Poyang Lake Basin, abbreviate to PYLB). The spatiotemporal variations of rainfall erosivity from 1961 to 2014 based on 57 meteorological stations were detected using the Mann-Kendall test, linear regression, and kriging interpolation method. The sequential t test analysis of regime shift (STARS) was employed to identify the abrupt changes of sediment load, and the modified double mass curve was used to assess the impacts of rainfall erosivity variability on sediment load. It was found that there was significant increase (P < 0.05) in rainfall erosivity in winter due to the significant increase in January over the last 54 years, whereas no trend in year and other seasons. Annual sediment load into the Poyang Lake (PYL) decreased significantly (P < 0.01) between 1961 and 2014, and the change-points were identified in both 1985 and 2003. It was found that take annual rainfall erosivity as the explanatory variables of the double mass curves is more reasonable than annual rainfall and erosive rainfall. The estimation via the modified double mass curve demonstrated that compared with the period before change-point (1961-1984), the changes of rainfall erosivity increased 8.0 and 2.1% of sediment load during 1985-2002 and 2003-2014, respectively. Human activities decreased 50.2 and 69.7% of sediment load during the last two periods, which indicated effects of human activities on sediment load change was much larger than that of rainfall erosivity variability in the PYLB.

[Dynamics of soil erosion at upper reaches of Minjiang River based on GIS].

PubMed

He, Xingyuan; Hu, Zhibi; Li, Yuehui; Hu, Yuanman

2005-12-01

Based on TM and ETM imagines, and employing GIS technique and empirical Revised Universal Soil Loss Equation (RUSLE) model, this paper studied the dynamics of soil erosion at the upper reaches of Minjiang River during three typical periods, with the main affecting factors analyzed. The results showed that the soil erosion area was increased by 1.28%, 1.84 % and 1.70% in 1986, 1995 and 2000, respectively. The average erosion modulus was increased from 832.64 t x km(-2) x yr(-1) in 1986 to 1048.74 t x km(-2) yr(-2) in 1995 and reached 1362.11 t x km(-2) yr(-1) in 2000, and soil loss was mainly of slight and light erosion, companying with a small quantity of middling erosion. The area of soil erosion was small, and the degree was light. There was a significant correlation between slope and soil loss, which mainly happened in the regions with a slope larger than 25 degrees, and accounted for 93.65%, 93.81% and 92.71% of the total erosion in 1986, 1995 and 2000, respectively. As for the altitude, middling, semi-high and high mountains and dry valley were liable to soil erosion, which accounted for 98.21%, 97.63% and 99.27% of the total erosion in 1986, 1995 and 2000, respectively. Different vegetation had a significant effect on soil erosion, and shrub and newly restored forest were the main erosion area. Excessive depasture not only resulted in the degradation of pasture, but also led to slight soil erosion. Land use type and soil type also contributed to soil loss, among which, dry-cinnamon soil and calcic gray-cinnamon soil were the most dangerous ones needing more protection. Soil loss was also linearly increased with increasing population and households, which suggested that the increase of population and households was the driving factor for soil loss increase in this area.

Electromagnetic Torque in Tokamaks with Toroidal Asymmetries

DOE Office of Scientific and Technical Information (OSTI.GOV)

Logan, Nikolas Christopher

2015-01-01

Lithium and boron coatings are applied to the walls of many tokamaks to enhance performance and protect the underlying substrates. Li and B-coated high-Z substrates are planned for use in NSTX-U and are a candidate plasma-facing component (PFC) for DEMO. However, previous measurements of Li evaporation and thermal sputtering on low-flux devices indicate that the Li temperature permitted on such devices may be unacceptably low. Thus it is crucial to characterize gross and net Li erosion rates under high-flux plasma bombardment. Additionally, no quantitative measurements have been performed of the erosion rate of a boron-coated PFC during plasma bombardment. Amore » realistic model for the compositional evolution of a Li layer under D bombardment was developed that incorporates adsorption, implantation, and diffusion. A model was developed for temperature-dependent mixed-material Li-D erosion that includes evaporation, physical sputtering, chemical sputtering, preferential sputtering, and thermal sputtering. The re-deposition fraction of a Li coating intersecting a linear plasma column was predicted using atomic physics information and by solving the Li continuity equation. These models were tested in the Magnum-PSI linear plasma device at ion fluxes of 10^23-10^24 m^-2 s^-1 and Li surface temperatures less than 800 degrees C. Li erosion was measured during bombardment with a neon plasma that will not chemically react with Li and the results agreed well with the erosion model. Next the ratio of the total D fluence to the areal density of the Li coating was varied to quantify differences in Li erosion under D plasma bombardment as a function of the D concentration. The ratio of D/Li atoms was calculated using the results of MD simulations and good agreement is observed between measurements and the predictions of the mixed-material erosion model. Li coatings are observed to disappear from graphite much faster than from TZM Mo, indicating that fast Li diffusion into the bulk graphite substrate occurred, as predicted. Li re-deposition fractions very close to unity are observed in Magnum-PSI, as predicted by modeling. Finally, predictions of Li coating lifetimes in the NSTX-U divertor are calculated. The gross erosion rate of boron coatings was also measured for the first time in a high-flux plasma device.« less

Soil erosion risk assessment using interviews, empirical soil erosion modeling (RUSLE) and fallout radionuclides in a volcanic crater lake watershed subjected to land use change, western Uganda

NASA Astrophysics Data System (ADS)

De Crop, Wannes; Ryken, Nick; Tomma Okuonzia, Judith; Van Ranst, Eric; Baert, Geert; Boeckx, Pascal; Verschuren, Dirk; Verdoodt, Ann

2017-04-01

Population pressure results in conversion of natural vegetation to cropland within the western Ugandan crater lake watersheds. These watersheds however are particularly prone to soil degradation and erosion because of the high rainfall intensity and steep topography. Increased soil erosion losses expose the aquatic ecosystems to excessive nutrient loading. In this study, the Katinda crater lake watershed, which is already heavily impacted by agricultural land use, was selected for an explorative study on its (top)soil characteristics - given the general lack of data on soils within these watersheds - as well as an assessment of soil erosion risks. Using group discussions and structured interviews, the local land users' perceptions on land use, soil quality, soil erosion and lake ecology were compiled. Datasets on rainfall, topsoil characteristics, slope gradient and length, and land use were collected. Subsequently a RUSLE erosion model was run. Results from this empirical erosion modeling approach were validated against soil erosion estimates based on 137Cs measurements.

Gully erosion in Moldova: evolution, importance and control

NASA Astrophysics Data System (ADS)

Leah, Tamara

2017-04-01

Soil erosion and landslides are major environmental problems in the Republic of Moldova, resulting in long-term impacts on land productivity and sustainable development of rural areas. Soil erosion occurs on about 1.5 million hectares of agricultural land. Erosion possible limits on agricultural land range from 3 t/ha to 180 t/ha. The weighted average in the country is 18.5 t/ ha/year. But once in 50-100 years the mentioned limits may be exceeded. Combination the physical-geographical complicate conditions with intensive agricultural activities on the slopes led to the development of linear (depth) erosion, from initial sheet and rills to entire systems of gullies and ravines. Depth erosion affects most powerful the slope land (60%) of southern steppe and central silvo-steppe zones of Moldova. Gullies refers to erosion forms named "agrierosional", which forms most often on slopes with a length of 500 m and inclination greater than 3°, pants occupied with vineyards and orchards. Annually on these slopes are formed 700-800 new gullies, with length of 50-70 km and an area of 300 hectares. As a result of the inadequate soil cultivation the gullies parameters are increased, that concentrates water runoff, intensifies soil erosion, forming corrugation on the soil surface and increase land and environment degradation. The first gullies inventory in Moldova was carried out in 1911, the following in 1965 and 1982. After this period their area was annual included in the land cadastral sheet. If in the 1911 the total number of gullies made up 9543 with an area of 14434 hectares, in 1965 was increased on average by 3.5 times and in the southern areas more than 10 times. Gullies density of the republic made up in 1911 - 0.42 unites/km2, in 1965 increased by 3 times and in some districts by 5-6 times. After 1965, a part of the land affected by gullies was gradually transformed from farmland into forest resources. This measure contributed to significant changes in agricultural land by reducing sudden decrease to the 1982 the index by gullies affection. The study of gullies intensity growth was achieved from 1966 in the main regions of Moldova. From 256 objects (gullies): 30% constitute those with weak growth (up to 0.3 m per year); 25% - with moderate growth (0.3-0.5 m) and 45% - with strong growth (0.5-1.5 m). There is no gully where would deprive their expansion process. Multiannual average growths of gullies are in large ranges - from 0.53 m on the Dniester Plateau to 1.48 m on the South Moldavian Plain. On the 1 January 2016 in the Republic of Moldova was registered 12031 hectares with gullies. Following active growth of depth erosion their total area annually increases with 300 hectares and the total destroyed land with 450-500 hectares. Linear and volume growth forecast of ravines (gullies) in different natural conditions of Moldova will be taken into consideration in designing of hydro-technical antierosion constructions and schemes to combat gullies erosion. Consequently, there is a need for erosion monitoring, special researches, experimental and modelling studies of gullies as a basis for predicting the effects of environmental change on gully erosion rates, implementation of measures to combat soil depth erosion in Moldova. Keywords: Agriculture activities, Erosion control, Gully erosion, Slope, Republic of Moldova

TESTING OF TMR SAND MANTIS FINAL REPORT

DOE Office of Scientific and Technical Information (OSTI.GOV)

Krementz, D; William Daugherty, W

2007-06-12

Screening tests of Sand Mantis candidate materials selected for erosion resistance have been completed. The results of this testing identified that over a relatively short period of operation (<1 hour), measurable erosion will occur in each of the candidate zoom tube materials given equal operating exposure. Additionally, this testing has shown that erosion of the rubber discharge hose directly downstream of the vehicle could be expected to limit the service life of the discharge hose. On the basis of these test results, SRNL recommends the following; {lg_bullet} redesign of critical system components (e.g., zoom tube, discharge hose) should be conductedmore » to improve system characteristics relative to erosion and capitalize on the results of this testing, {lg_bullet} continued efforts to deploy the Sand Mantis should include testing to better define and optimize operating parameters, and gain an understanding of system dynamics, {lg_bullet} discontinue wear testing with the selected materials pending redesign of critical system components (1st recommendation) and inclusion of other candidate materials. The final selection of additional candidate materials should be made following design changes, but might include a Stellite alloy or zirconia.« less

Cavitation pitting and erosion of aluminum 6061-T6 in mineral oil water

NASA Technical Reports Server (NTRS)

Rao, B. C. S.; Buckley, D. H.

1983-01-01

Cavitation erosion studies of aluminum 6061-T6 in mineral oil and in ordinary tap water are presented. The maximum erosion rate (MDPR, or mean depth of penetration rate) in mineral oil was about four times that in water. The MDPR in mineral oil decreased continuously with time, but the MDPR in water remained approximately constant. The cavitation pits in mineral oil were of smaller diameter and depth than the pits in water. Treating the pits as spherical segments, we computed the radius r of the sphere. The logarithm of h/a, where h is the pit depth and 2a is the top width of the pit, was linear when plotted against the logarithm of 2r/h - 1.

Erosion Risks in Selected Watersheds for the 2005 School Fire Located Near Pomeroy, Washington on Predominately Ash-Cap Soils

Treesearch

William Elliot; Ina Sue Miller; Brandon Glaza

2007-01-01

A limited erosion potential analysis was carried out on the 50,000 acre School Fire. Three WEPP interfaces were used for the analysis, a GIS wizard, an online interface and a windows interface. Ten watersheds within the fire area were modeled with the GeoWEPP tool (a geo-spatial interface for WEPP, Water Erosion Predication Project). The watersheds covered 18,823 acres...

Reduction of erosive wear in situ by stannous fluoride-containing toothpaste.

PubMed

Huysmans, M C D N J M; Jager, D H J; Ruben, J L; Unk, D E M F; Klijn, C P A H; Vieira, A M

2011-01-01

Stannous fluoride (SnF) has been suggested as a dental erosion-preventive agent. The aim of this single-centre, randomized, double-blind, in situ study was to evaluate the effect of toothpastes with SnF in the prevention of erosive enamel wear. A combined split-mouth (extra-oral water or toothpaste brushing) and crossover (type of toothpaste) set-up was used. Twelve volunteers wore palatal appliances containing human enamel samples. Three toothpastes were used, in three consecutive runs, in randomized order: two toothpastes containing SnF (coded M and PE) and one toothpaste containing only sodium fluoride (coded C). On day 1 of each run the appliances were worn for pellicle formation. On days 2-5 the samples were also brushed twice with a toothpaste-water slurry or only water (control). Erosion took place on days 2-5 extra-orally 3 times a day (5 min) in a citric acid solution (pH 2.3). Enamel wear depth was quantified by optical profilometry. The effect of toothpastes was tested using General Linear Modeling. Average erosive wear depth of control samples was 23 μm. Both SnF toothpastes significantly reduced erosive wear: M by 34% (SD 39%) and PE by 26% (SD 25%). The control toothpaste reduced erosive wear non-significantly by 7% (SD 20%). Both SnF-containing toothpastes significantly reduced erosive wear compared to the sodium fluoride toothpaste. We conclude that SnF-containing toothpastes are able to reduce erosive tooth wear in situ. Copyright © 2011 S. Karger AG, Basel.

Two cases of erosive oral lichen planus with autoantibodies to desmoglein 3.

PubMed

Muramatsu, Ken; Nishie, Wataru; Natsuga, Ken; Fujita, Yasuyuki; Iwata, Hiroaki; Yamada, Tamaki; Yamashita, Emi; Asaka, Takuya; Shimizu, Hiroshi

2016-11-01

Oral lichen planus (OLP) is a chronic inflammatory disorder of the oral mucosa of unknown etiology. Clinically, the erosive type of OLP (erosive OLP) can show features similar to those of pemphigus vulgaris (PV), an autoimmune blistering disorder in which desmoglein (Dsg)3 is targeted. In addition to clinical and histopathological findings, immunological studies, including direct immunofluorescence (IF), indirect IF and enzyme-linked immunosorbent assay (ELISA) that detect autoantibodies to Dsg3, are helpful in differentiating erosive OLP from PV. Here, we show two cases of erosive OLP with autoantibodies to Dsg3. Patient 1 was a 68-year-old woman with chronic erosions of the oral mucosa, in which elevated levels of immunoglobulin (Ig)G autoantibodies to Dsg1 and Dsg3 were detected by ELISA. Patient 2 was an 85-year-old woman with white striae with erosions on the lateral sides of the buccal mucosa with elevated levels of IgG autoantibodies to Dsg3 detected by ELISA. Histopathological findings from both cases showed lichenoid dermatitis, and both direct and indirect IF showed no tissue-bound IgG autoantibodies. From these findings, the diagnosis of erosive OLP was made. Immunological assays revealed both cases to have IgG-directing calcium-independent linear epitopes on Dsg3, which are suggestive of non-pathogenic autoantibodies. In addition, autoantibodies to Dsg3 in patient 2 reacted with a prosequence-possessing precursor form of Dsg3 but not with the mature form of the molecule. The present study suggests that erosive OLP may develop anti-Dsg3 autoantibodies, which should be carefully assessed. © 2016 Japanese Dermatological Association.

Current and future assessments of soil erosion by water on the Tibetan Plateau based on RUSLE and CMIP5 climate models.

PubMed

Teng, Hongfen; Liang, Zongzheng; Chen, Songchao; Liu, Yong; Viscarra Rossel, Raphael A; Chappell, Adrian; Yu, Wu; Shi, Zhou

2018-04-18

Soil erosion by water is accelerated by a warming climate and negatively impacts water security and ecological conservation. The Tibetan Plateau (TP) has experienced warming at a rate approximately twice that observed globally, and heavy precipitation events lead to an increased risk of erosion. In this study, we assessed current erosion on the TP and predicted potential soil erosion by water in 2050. The study was conducted in three steps. During the first step, we used the Revised Universal Soil Equation (RUSLE), publicly available data, and the most recent earth observations to derive estimates of annual erosion from 2002 to 2016 on the TP at 1-km resolution. During the second step, we used a multiple linear regression (MLR) model and a set of climatic covariates to predict rainfall erosivity on the TP in 2050. The MLR was used to establish the relationship between current rainfall erosivity data and a set of current climatic and other covariates. The coefficients of the MLR were generalised with climate covariates for 2050 derived from the fifth phase of the Coupled Model Intercomparison Project (CMIP5) models to estimate rainfall erosivity in 2050. During the third step, soil erosion by water in 2050 was predicted using rainfall erosivity in 2050 and other erosion factors. The results show that the mean annual soil erosion rate on the TP under current conditions is 2.76tha -1 y -1 , which is equivalent to an annual soil loss of 559.59×10 6 t. Our 2050 projections suggested that erosion on the TP will increase to 3.17tha -1 y -1 and 3.91tha -1 y -1 under conditions represented by RCP2.6 and RCP8.5, respectively. The current assessment and future prediction of soil erosion by water on the TP should be valuable for environment protection and soil conservation in this unique region and elsewhere. Copyright © 2018 Elsevier B.V. All rights reserved.

Modelling sheet erosion on steep slopes in the loess region of China

NASA Astrophysics Data System (ADS)

Wu, Bing; Wang, Zhanli; Zhang, Qingwei; Shen, Nan; Liu, June

2017-10-01

The relationship of sheet erosion rate (SE), slope gradient (S) and rainfall intensity (I), and hydraulic parameters, such as flow velocity (V), shear stress (τ), stream power (Ω) and unit stream power (P), was investigated to derive an accurate experimental model. The experiment was conducted at slopes of 12.23%, 17.63%, 26.8%, 36.4%, 40.4% and 46.63% under I of 48, 60, 90, 120, 138 and 150 mm h-1, respectively, using simulated rainfall. Results showed that sheet erosion rate increased as a power function with rainfall intensity and slope gradient with R2 = 0.95 and Nash-Sutcliffe model efficiency (NSE) = 0.87. Sheet erosion rate was more sensitive to rainfall intensity than to slope gradient. It increased as a power function with flow velocity, which was satisfactory for predicting sheet erosion rate with R2 = 0.95 and NSE = 0.81. Shear stress and stream power could be used to predict sheet erosion rate accurately with a linear function equation. Stream power (R2 = 0.97, NSE = 0.97) was a better predictor of sheet erosion rather than shear stress (R2 = 0.90, NSE = 0.89). However, a prediction based on unit stream power was poor. The new equation (i.e. SE = 7.5 ×1012S1.43I3.04 and SE = 0.06 Ω - 0.0003 and SE = 0.011 τ - 0.01) would improve water erosion estimation on loess hillslopes of China.

When do glaciated landscapes form?

NASA Astrophysics Data System (ADS)

Koppes, M. N.

2015-12-01

Glacial erosion is a fundamental link between climate and the tectonic and surface processes that create topography. Mountain ranges worldwide have undergone large-scale modification due the erosive action of ice masses, yet the mechanisms that control the timing of this modification and the rate by which ice erodes remain poorly understood. Available data report a wide range of erosion rates from individual ice masses over varying timescales, from the modern to orogenic. Recent numerical modeling efforts have focused on replicating the processes that produce the geomorphic signatures of glacial landscapes. Central to these models is a simple index that relates erosion rate to ice dynamics. To provide a quantitative test of the links between glacial erosion, sliding and ice discharge, we examined explicitly the factors controlling modern glacier erosion rates across climatic regimes, from Patagonia to the Antarctic Peninsula. We find that modern, basin-averaged erosion rates vary by three orders of magnitude, from 1->10 mm yr-1 in Patagonia to 0.01-<0.1 mm yr-1 in the AP, largely as a function of temperature and basal thermal regime. Erosion rates also increase non-linearly with both the sliding speed and the ice flux through the ELA, in accord with theories of glacial erosion. Notably, erosion rates decrease by over two orders of magnitude between temperate and polar glaciers with similar discharge rates. The difference in erosion rates between temperate and colder glaciers of similar shape and size is primarily related to the abundance of meltwater accessing the bed. Since all glaciers worldwide have experienced colder than current climatic conditions, the 100-fold decrease in long-term relative to modern erosion rates may in part reflect the temporal averaging of temperate and polar conditions over the lifecycle of these glaciers. Hence, climatic variation, more than the extent of ice cover or tectonic changes, controls the pace at which glaciers shape mountains.

Erosion-driven uplift in the Gamburtsev Subglacial Mountains of East Antarctica

NASA Astrophysics Data System (ADS)

Paxman, G. J. G.; Watts, A. B.; Ferraccioli, F.; Jordan, T. A.; Bell, R. E.; Jamieson, S. S. R.; Finn, C. A.

2016-10-01

The relative roles of climate and tectonics in mountain building have been widely debated. Central to this debate is the process of flexural uplift in response to valley incision. Here we quantify this process in the Gamburtsev Subglacial Mountains, a paradoxical tectonic feature in cratonic East Antarctica. Previous studies indicate that rifting and strike-slip tectonics may have provided a key trigger for the initial uplift of the Gamburtsevs, but the contribution of more recent valley incision remains to be quantified. Inverse spectral (free-air admittance and Bouguer coherence) methods indicate that, unusually for continents, the coherence between free-air gravity anomalies and bedrock topography is high (>0.5) and that the elastic thickness of the lithosphere is anomalously low (<15 km), in contrast to previously reported values of up to ∼70 km. The isostatic effects of two different styles of erosion are quantified: dendritic fluvial incision overprinted by Alpine-style glacial erosion in the Gamburtsevs and outlet glacier-type selective linear erosion in the Lambert Rift, part of the East Antarctic Rift System. 3D flexural models indicate that valley incision has contributed ca. 500 m of peak uplift in the Gamburtsevs and up to 1.2 km in the Lambert Rift, which is consistent with the present-day elevation of Oligocene-Miocene glaciomarine sediments. Overall, we find that 17-25% of Gamburtsev peak uplift can be explained by erosional unloading. These relatively low values are typical of temperate mountain ranges, suggesting that most of the valley incision in the Gamburtsevs occurred prior to widespread glaciation at 34 Ma. The pre-incision topography of the Gamburtsevs lies at 2-2.5 km above sea-level, confirming that they were a key inception point for the development of the East Antarctic Ice Sheet. Tectonic and/or dynamic processes were therefore responsible for ca. 80% of the elevation of the modern Gamburtsev Subglacial Mountains.

Large-scale assessment of soil erosion in Africa: satellites help to jointly account for dynamic rainfall and vegetation cover

NASA Astrophysics Data System (ADS)

Vrieling, Anton; Hoedjes, Joost C. B.; van der Velde, Marijn

2015-04-01

Efforts to map and monitor soil erosion need to account for the erratic nature of the soil erosion process. Soil erosion by water occurs on sloped terrain when erosive rainfall and consequent surface runoff impact soils that are not well-protected by vegetation or other soil protective measures. Both rainfall erosivity and vegetation cover are highly variable through space and time. Due to data paucity and the relative ease of spatially overlaying geographical data layers into existing models like USLE (Universal Soil Loss Equation), many studies and mapping efforts merely use average annual values for erosivity and vegetation cover as input. We first show that rainfall erosivity can be estimated from satellite precipitation data. We obtained average annual erosivity estimates from 15 yr of 3-hourly TRMM Multi-satellite Precipitation Analysis (TMPA) data (1998-2012) using intensity-erosivity relationships. Our estimates showed a positive correlation (r = 0.84) with long-term annual erosivity values of 37 stations obtained from literature. Using these TMPA erosivity retrievals, we demonstrate the large interannual variability, with maximum annual erosivity often exceeding two to three times the mean value, especially in semi-arid areas. We then calculate erosivity at a 10-daily time-step and combine this with vegetation cover development for selected locations in Africa using NDVI - normalized difference vegetation index - time series from SPOT VEGETATION. Although we do not integrate the data at this point, the joint analysis of both variables stresses the need for joint accounting for erosivity and vegetation cover for large-scale erosion assessment and monitoring.

Susceptibility of bovine dental enamel with initial erosion lesion to new erosive challenges

PubMed Central

Tereza, Guida Paola Genovez; Boteon, Ana Paula; Ferrairo, Brunna Mota; Gonçalves, Priscilla Santana Pinto; da Silva, Thiago Cruvinel; Honório, Heitor Marques; Rios, Daniela

2017-01-01

This in vitro study evaluated the impact of initial erosion on the susceptibility of enamel to further erosive challenge. Thirty bovine enamel blocks were selected by surface hardness and randomized into two groups (n = 15): GC- group composed by enamel blocks without erosion lesion and GT- group composed by enamel blocks with initial erosion lesion. The baseline profile of each block was determined using the profilometer. The initial erosion was produced by immersing the blocks into HCl 0.01 M, pH 2.3 for 30 seconds, under stirring. The erosive cycling consisted of blocks immersion in hydrochloric acid (0.01 M, pH 2.3) for 2 minutes, followed by immersion in artificial saliva for 120 minutes. This procedure was repeated 4 times a day for 5 days, and the blocks were kept in artificial saliva overnight. After erosive cycling, final profile measurement was performed. Profilometry measured the enamel loss by the superposition of initial and final profiles. Data were analyzed by t-test (p<0.05). The result showed no statistically significant difference between groups (GS = 14.60±2.86 and GE = .14.69±2.21 μm). The presence of initial erosion on bovine dental enamel does not enhance its susceptibility to new erosive challenges. PMID:28817591

Susceptibility of bovine dental enamel with initial erosion lesion to new erosive challenges.

PubMed

Oliveira, Gabriela Cristina de; Tereza, Guida Paola Genovez; Boteon, Ana Paula; Ferrairo, Brunna Mota; Gonçalves, Priscilla Santana Pinto; Silva, Thiago Cruvinel da; Honório, Heitor Marques; Rios, Daniela

2017-01-01

This in vitro study evaluated the impact of initial erosion on the susceptibility of enamel to further erosive challenge. Thirty bovine enamel blocks were selected by surface hardness and randomized into two groups (n = 15): GC- group composed by enamel blocks without erosion lesion and GT- group composed by enamel blocks with initial erosion lesion. The baseline profile of each block was determined using the profilometer. The initial erosion was produced by immersing the blocks into HCl 0.01 M, pH 2.3 for 30 seconds, under stirring. The erosive cycling consisted of blocks immersion in hydrochloric acid (0.01 M, pH 2.3) for 2 minutes, followed by immersion in artificial saliva for 120 minutes. This procedure was repeated 4 times a day for 5 days, and the blocks were kept in artificial saliva overnight. After erosive cycling, final profile measurement was performed. Profilometry measured the enamel loss by the superposition of initial and final profiles. Data were analyzed by t-test (p<0.05). The result showed no statistically significant difference between groups (GS = 14.60±2.86 and GE = .14.69±2.21 μm). The presence of initial erosion on bovine dental enamel does not enhance its susceptibility to new erosive challenges.

Solutal convection induced by dissolution. Influence on erosion dynamics and interface shaping.

NASA Astrophysics Data System (ADS)

Berhanu, Michael; Philippi, Julien; Cohen, Caroline; Derr, Julien; Courrech du Pont, Sylvain

2017-04-01

Rock fractures invaded by a water flow, are often subjected to dissolution, which let grow and evolve the initial fracture network, by evacuating the eroded minerals under a solute form. In the case of fast kinetic of dissolution, local erosion rate is set by the advection of the solute. The erosion velocity decreases indeed with the solute concentration at the interface and vanishes when this concentration reaches the saturation value. Even in absence of an imposed or external flow, advection can drive the dissolution, when buoyancy effects due to gravity induce a solutal convection flow, which controls the erosive dynamics and modifies the shape of the dissolving interface. Here, we investigate using model experiments with fast dissolving materials and numerical simulations in simplified situations, solutal convection induced by dissolution. Results are interpreted regarding a linear stability analysis of the corresponding solutal Rayleigh-Benard instability. A dissolving surface is suspended above a water height, initially at rest. In a first step, solute flux is transported through a growing diffusion layer. Then after an onset time, once the layer exceeds critical width, convection flow starts under the form of falling plumes. A dynamic equilibrium results in average from births and deaths of intermittent plumes, setting the size of the solute concentration boundary layer at the interface and thus the erosion velocity. Solutal convection can also induce a pattern on the dissolving interface. We show experimentally with suspended and inclined blocks of salt and sugar, that in a linear stage, the first wavelength of the dissolution pattern corresponds to the wavelength of the convection instability. Then pattern evolves to more complex shapes due to non-linear interactions between the flow and the eroded interface. More generally, we inquire what are the conditions to observe a such solutal convection instability in geological situations and if the properties of dissolution patterns can be related to the characteristic of the convective flow. C. Oltéan, F. Golfier and M.A. Buès, Numerical and experimental investigation of buoyancy-driven dissolution in vertical fracture, J. Geophys. Res. Solid Earth, 118(5), 2038-2048 (2013) C. Cohen, M. Berhanu, J. Derr and S. Courrech du Pont, Erosion patterns on dissolving and melting bodies (2015 Gallery of Fluid motion), Phys. Rev. Fluids, 1, 050508 (2016) T. S. Sullivan, Y. Liu, and R. E. Ecke, Turbulent solutal convection and surface patterning in solid dissolution, Phys. Rev. E 54, 486 (1996)

Computation of rainfall erosivity from daily precipitation amounts.

PubMed

Beguería, Santiago; Serrano-Notivoli, Roberto; Tomas-Burguera, Miquel

2018-10-01

Rainfall erosivity is an important parameter in many erosion models, and the EI30 defined by the Universal Soil Loss Equation is one of the best known erosivity indices. One issue with this and other erosivity indices is that they require continuous breakpoint, or high frequency time interval, precipitation data. These data are rare, in comparison to more common medium-frequency data, such as daily precipitation data commonly recorded by many national and regional weather services. Devising methods for computing estimates of rainfall erosivity from daily precipitation data that are comparable to those obtained by using high-frequency data is, therefore, highly desired. Here we present a method for producing such estimates, based on optimal regression tools such as the Gamma Generalised Linear Model and universal kriging. Unlike other methods, this approach produces unbiased and very close to observed EI30, especially when these are aggregated at the annual level. We illustrate the method with a case study comprising more than 1500 high-frequency precipitation records across Spain. Although the original records have a short span (the mean length is around 10 years), computation of spatially-distributed upscaling parameters offers the possibility to compute high-resolution climatologies of the EI30 index based on currently available, long-span, daily precipitation databases. Copyright © 2018 Elsevier B.V. All rights reserved.

Designing a national soil erosion monitoring network for England and Wales

NASA Astrophysics Data System (ADS)

Lark, Murray; Rawlins, Barry; Anderson, Karen; Evans, Martin; Farrow, Luke; Glendell, Miriam; James, Mike; Rickson, Jane; Quine, Timothy; Quinton, John; Brazier, Richard

2014-05-01

Although soil erosion is recognised as a significant threat to sustainable land use and may be a priority for action in any forthcoming EU Soil Framework Directive, those responsible for setting national policy with respect to erosion are constrained by a lack of robust, representative, data at large spatial scales. This reflects the process-orientated nature of much soil erosion research. Recognising this limitation, The UK Department for Environment, Food and Rural Affairs (Defra) established a project to pilot a cost-effective framework for monitoring of soil erosion in England and Wales (E&W). The pilot will compare different soil erosion monitoring methods at a site scale and provide statistical information for the final design of the full national monitoring network that will: provide unbiased estimates of the spatial mean of soil erosion rate across E&W (tonnes ha-1 yr-1) for each of three land-use classes - arable and horticultural grassland upland and semi-natural habitats quantify the uncertainty of these estimates with confidence intervals. Probability (design-based) sampling provides most efficient unbiased estimates of spatial means. In this study, a 16 hectare area (a square of 400 x 400 m) positioned at the centre of a 1-km grid cell, selected at random from mapped land use across E&W, provided the sampling support for measurement of erosion rates, with at least 94% of the support area corresponding to the target land use classes. Very small or zero erosion rates likely to be encountered at many sites reduce the sampling efficiency and make it difficult to compare different methods of soil erosion monitoring. Therefore, to increase the proportion of samples with larger erosion rates without biasing our estimates, we increased the inclusion probability density in areas where the erosion rate is likely to be large by using stratified random sampling. First, each sampling domain (land use class in E&W) was divided into strata; e.g. two sub-domains within which, respectively, small or no erosion rates, and moderate or larger erosion rates are expected. Each stratum was then sampled independently and at random. The sample density need not be equal in the two strata, but is known and is accounted for in the estimation of the mean and its standard error. To divide the domains into strata we used information on slope angle, previous interpretation of erosion susceptibility of the soil associations that correspond to the soil map of E&W at 1:250 000 (Soil Survey of England and Wales, 1983), and visual interpretation of evidence of erosion from aerial photography. While each domain could be stratified on the basis of the first two criteria, air photo interpretation across the whole country was not feasible. For this reason we used a two-phase random sampling for stratification (TPRS) design (de Gruijter et al., 2006). First, we formed an initial random sample of 1-km grid cells from the target domain. Second, each cell was then allocated to a stratum on the basis of the three criteria. A subset of the selected cells from each stratum were then selected for field survey at random, with a specified sampling density for each stratum so as to increase the proportion of cells where moderate or larger erosion rates were expected. Once measurements of erosion have been made, an estimate of the spatial mean of the erosion rate over the target domain, its standard error and associated uncertainty can be calculated by an expression which accounts for the estimated proportions of the two strata within the initial random sample. de Gruijter, J.J., Brus, D.J., Biekens, M.F.P. & Knotters, M. 2006. Sampling for Natural Resource Monitoring. Springer, Berlin. Soil Survey of England and Wales. 1983 National Soil Map NATMAP Vector 1:250,000. National Soil Research Institute, Cranfield University.

Dental erosion in 12-year-old school children living in Jakarta

NASA Astrophysics Data System (ADS)

Septalita, A.; Bahar, A.; Agustanti, A.; Rahardjo, A.; Maharani, D. A.; Rosalien, R.

2017-08-01

This study assesses the dental erosion status of 12-year-old Indonesian children and studies the determinants of dental erosion of these children. The survey was performed in 2016 with ethics approval. A multistage cluster proportional to size random sampling method was adopted to select 12-year-old children in 24 primary schools in Jakarta. The parents were asked to complete a self-administered questionnaire concerning their children’s diet and oral health habits. The children were examined by a single calibrated examiner. Detection of dental erosion followed basic erosive wear examination (BEWE) criteria. A total of 487 children participated in the survey. Most children (88%) had at least some signs of erosion (BEWE > 0), with dentin being involved in 50% of the cases (BEWE = 2). Dental erosion was significantly related to gender, the frequencies of citric tea consumption, parent’s dental knowledge, father’s education, and dental caries (OR = 3.148). The 12-year-old Indonesian school children who lived in Jakarta had signs of erosion, although severe erosion was not found. Screening programs should be provided to identify risk groups so early preventive measures can be taken.

Rainfall erosivity in Europe.

PubMed

Panagos, Panos; Ballabio, Cristiano; Borrelli, Pasquale; Meusburger, Katrin; Klik, Andreas; Rousseva, Svetla; Tadić, Melita Perčec; Michaelides, Silas; Hrabalíková, Michaela; Olsen, Preben; Aalto, Juha; Lakatos, Mónika; Rymszewicz, Anna; Dumitrescu, Alexandru; Beguería, Santiago; Alewell, Christine

2015-04-01

Rainfall is one the main drivers of soil erosion. The erosive force of rainfall is expressed as rainfall erosivity. Rainfall erosivity considers the rainfall amount and intensity, and is most commonly expressed as the R-factor in the USLE model and its revised version, RUSLE. At national and continental levels, the scarce availability of data obliges soil erosion modellers to estimate this factor based on rainfall data with only low temporal resolution (daily, monthly, annual averages). The purpose of this study is to assess rainfall erosivity in Europe in the form of the RUSLE R-factor, based on the best available datasets. Data have been collected from 1541 precipitation stations in all European Union (EU) Member States and Switzerland, with temporal resolutions of 5 to 60 min. The R-factor values calculated from precipitation data of different temporal resolutions were normalised to R-factor values with temporal resolutions of 30 min using linear regression functions. Precipitation time series ranged from a minimum of 5 years to a maximum of 40 years. The average time series per precipitation station is around 17.1 years, the most datasets including the first decade of the 21st century. Gaussian Process Regression (GPR) has been used to interpolate the R-factor station values to a European rainfall erosivity map at 1 km resolution. The covariates used for the R-factor interpolation were climatic data (total precipitation, seasonal precipitation, precipitation of driest/wettest months, average temperature), elevation and latitude/longitude. The mean R-factor for the EU plus Switzerland is 722 MJ mm ha(-1) h(-1) yr(-1), with the highest values (>1000 MJ mm ha(-1) h(-1) yr(-1)) in the Mediterranean and alpine regions and the lowest (<500 MJ mm ha(-1) h(-1) yr(-1)) in the Nordic countries. The erosivity density (erosivity normalised to annual precipitation amounts) was also the highest in Mediterranean regions which implies high risk for erosive events and floods. Copyright © 2015 The Authors. Published by Elsevier B.V. All rights reserved.

Robotic weld overlay coatings for erosion control

NASA Astrophysics Data System (ADS)

The erosion of materials by the impact of solid particles has received increasing attention during the past twenty years. Recently, research has been initiated with the event of advanced coal conversion processes in which erosion plays an important role. The resulting damage, termed Solid Particle Erosion (SPE), is of concern primarily because of the significantly increased operating costs which result in material failures. Reduced power plant efficiency due to solid particle erosion of boiler tubes and waterfalls has led to various methods to combat SPE. One method is to apply coatings to the components subjected to erosive environments. Protective weld overlay coatings are particularly advantageous in terms of coating quality. The weld overlay coatings are essentially immune to spallation due to a strong metallurgical bond with the substrate material. By using powder mixtures, multiple alloys can be mixed in order to achieve the best performance in an erosive environment. However, a review of the literature revealed a lack of information on weld overlay coating performance in erosive environments which makes the selection of weld overlay alloys a difficult task. The objective of this project is to determine the effects of weld overlay coating composition and microstructure on erosion resistance. These results will lead to a better understanding of erosion mitigation in CFB's.

Threats to coastal communities of Mahanadi delta due to imminent consequences of erosion - Present and near future.

PubMed

Mukhopadhyay, Anirban; Ghosh, Pramit; Chanda, Abhra; Ghosh, Amit; Ghosh, Subhajit; Das, Shouvik; Ghosh, Tuhin; Hazra, Sugata

2018-05-11

Coastal erosion is a natural hazard which causes significant loss to properties as well as coastal habitats. Coastal districts of Mahanadi delta, one of the most populated deltas of the Indian subcontinent, are suffering from the ill effects of coastal erosion. An important amount of assets is being lost every year along with forced migration of huge portions of coastal communities due to erosion. An attempt has been made in this study to predict the future coastline of the Mahanadi Delta based on historical trends. Historical coastlines of the delta have been extracted using semi-automated Tasselled Cap technique from the LANDSAT satellite imageries of the year 1990, 1995, 2000, 2006 and 2010. Using Digital Shoreline Assessment System (DSAS) tool of USGS, the trend of the coastline has been assessed in the form of End Point Rate (EPR) and Linear Regression Rate (LRR). A hybrid methodology has been adopted using statistical (EPR) and trigonometric functions to predict the future positions of the coastlines of the years 2020, 2035 and 2050. The result showed that most of the coastline (≈65%) is facing erosion at present. The predicted outcome shows that by the end of year 2050 the erosion scenario will worsen which in turn would lead to very high erosion risk for 30% of the total coastal mouzas (small administrative blocks). This study revealed the coastal erosion trend of Mahanadi delta and based on the predicted coastlines it can be inferred that the coastal communities in near future would be facing substantial threat due to erosion particularly in areas surrounding Puri (a renowned tourist pilgrimage) and Paradwip (one of the busiest ports and harbours of the country). Copyright © 2018 Elsevier B.V. All rights reserved.

Characterisation of anti-erosive properties of nanocomposite coatings by the methods of sclerometry

NASA Astrophysics Data System (ADS)

Kudryakov, O. V.; Varavka, V. N.; Ilyasov, V. V.

2017-05-01

Results of research of coatings of the different metal-ceramics systems are given. Coatings were received by ion-plasma sedimentation in vacuum in the form of multilayered composite material, which had a thickness of layers within nanometric range. Selection of composite systems is determined by applied research problem - namely designing of the anti-erosive coatings durable in the condition of drop impingement impacts. For this purpose the sclerometric studies, the bench erosive tests and optimization of the obtained data were done.

Polarization sensitive camera for the in vitro diagnostic and monitoring of dental erosion

NASA Astrophysics Data System (ADS)

Bossen, Anke; Rakhmatullina, Ekaterina; Lussi, Adrian; Meier, Christoph

Due to a frequent consumption of acidic food and beverages, the prevalence of dental erosion increases worldwide. In an initial erosion stage, the hard dental tissue is softened due to acidic demineralization. As erosion progresses, a gradual tissue wear occurs resulting in thinning of the enamel. Complete loss of the enamel tissue can be observed in severe clinical cases. Therefore, it is essential to provide a diagnosis tool for an accurate detection and monitoring of dental erosion already at early stages. In this manuscript, we present the development of a polarization sensitive imaging camera for the visualization and quantification of dental erosion. The system consists of two CMOS cameras mounted on two sides of a polarizing beamsplitter. A horizontal linearly polarized light source is positioned orthogonal to the camera to ensure an incidence illumination and detection angles of 45°. The specular reflected light from the enamel surface is collected with an objective lens mounted on the beam splitter and divided into horizontal (H) and vertical (V) components on each associate camera. Images of non-eroded and eroded enamel surfaces at different erosion degrees were recorded and assessed with diagnostic software. The software was designed to generate and display two types of images: distribution of the reflection intensity (V) and a polarization ratio (H-V)/(H+V) throughout the analyzed tissue area. The measurements and visualization of these two optical parameters, i.e. specular reflection intensity and the polarization ratio, allowed detection and quantification of enamel erosion at early stages in vitro.

Dynamics of Soil Organic Carbon and Microbial Biomass Carbon in Relation to Water Erosion and Tillage Erosion

PubMed Central

Xiaojun, Nie; Jianhui, Zhang; Zhengan, Su

2013-01-01

Dynamics of soil organic carbon (SOC) are associated with soil erosion, yet there is a shortage of research concerning the relationship between soil erosion, SOC, and especially microbial biomass carbon (MBC). In this paper, we selected two typical slope landscapes including gentle and steep slopes from the Sichuan Basin, China, and used the 137Cs technique to determine the effects of water erosion and tillage erosion on the dynamics of SOC and MBC. Soil samples for the determination of 137Cs, SOC, MBC and soil particle-size fractions were collected on two types of contrasting hillslopes. 137Cs data revealed that soil loss occurred at upper slope positions of the two landscapes and soil accumulation at the lower slope positions. Soil erosion rates as well as distribution patterns of the <0.002-mm clay shows that water erosion is the major process of soil redistribution in the gentle slope landscape, while tillage erosion acts as the dominant process of soil redistribution in the steep slope landscape. In gentle slope landscapes, both SOC and MBC contents increased downslope and these distribution patterns were closely linked to soil redistribution rates. In steep slope landscapes, only SOC contents increased downslope, dependent on soil redistribution. It is noticeable that MBC/SOC ratios were significantly lower in gentle slope landscapes than in steep slope landscapes, implying that water erosion has a negative effect on the microbial biomass compared with tillage erosion. It is suggested that MBC dynamics are closely associated with soil redistribution by water erosion but independent of that by tillage erosion, while SOC dynamics are influenced by soil redistribution by both water erosion and tillage erosion. PMID:23717530

Insights into lateral marsh retreat mechanism through localized field measurements

NASA Astrophysics Data System (ADS)

Bendoni, M.; Mel, R.; Solari, L.; Lanzoni, S.; Francalanci, S.; Oumeraci, H.

2016-02-01

Deterioration of salt marshes may be due to several factors related to increased anthropic pressure, sea level rise, and erosive processes. While salt marshes can reach equilibrium in the vertical direction, adapting to sea level rise, they are inherently unstable in the horizontal direction. Marsh boundaries are characterized by scarps with bare sediment below the vegetated surface layer that can be easily removed by wave-induced erosion. In this work, we explore the different mechanisms involved in the erosion of marsh borders through the interpretation of field data. The analysis is based on a systematic field monitoring of a salt marsh in the Venice Lagoon subject to lateral erosion. Measurements included horizontal retreat of the scarp at various locations and wave height in front of the marsh during three storm surges. Continuous erosion and mass failures alternated during the observed period, leading to an average retreat up to 80 cm/yr. The data, collected roughly every month for 1.5 year, indicate that the linear relation that links the observed erosion rate to the impinging wave power exhibits a larger slope than that already estimated in literature on the basis of long-term surveys. Moreover, an increase in the gradient of erodibility is detected along the marsh scarp, due to the combined action of soil strengthening by vegetation on the marsh surface and the impact of wave breaking at the bank toe, which promote cantilever failures and increase the lateral erosion rate.

Scenario Studies on Effects of Soil Infiltration Rates, Land Slope, and Furrow Irrigation Characteristics on Furrow Irrigation-Induced Erosion.

PubMed

Dibal, Jibrin M; Ramalan, A A; Mudiare, O J; Igbadun, H E

2014-01-01

Furrow irrigation proceeds under several soil-water-furrow hydraulics interaction dynamics. The soil erosion consequences from such interactions in furrow irrigation in Samaru had remained uncertain. A furrow irrigation-induced erosion (FIIE) model was used to simulate the potential severity of soil erosion in irrigated furrows due to interactive effects of infiltration rates, land slope, and some furrow irrigation characteristics under different scenarios. The furrow irrigation characteristics considered were furrow lengths, widths, and stream sizes. The model itself was developed using the dimensional analysis approach. The scenarios studied were the interactive effects of furrow lengths, furrow widths, and slopes steepness; infiltration rates and furrow lengths; and stream sizes, furrow lengths, and slopes steepness on potential furrow irrigation-induced erosion, respectively. The severity of FIIE was found to relate somewhat linearly with slope and stream size, and inversely with furrow lengths and furrow width. The worst soil erosion (378.05 t/ha/yr) was found as a result of the interactive effects of 0.65 m furrow width, 50 m furrow length, and 0.25% slope steepness; and the least soil erosion (0.013 t/ha/yr) was induced by the combined effects of 0.5 l/s, 200 m furrow length, and 0.05% slope steepness. Evidently considering longer furrows in furrow irrigation designs would be a better alternative of averting excessive FIIE.

Evaluation and selection of indicators for land degradation and desertification monitoring: types of degradation, causes, and implications for management.

PubMed

Kairis, Or; Kosmas, C; Karavitis, Ch; Ritsema, C; Salvati, L; Acikalin, S; Alcalá, M; Alfama, P; Atlhopheng, J; Barrera, J; Belgacem, A; Solé-Benet, A; Brito, J; Chaker, M; Chanda, R; Coelho, C; Darkoh, M; Diamantis, I; Ermolaeva, O; Fassouli, V; Fei, W; Feng, J; Fernandez, F; Ferreira, A; Gokceoglu, C; Gonzalez, D; Gungor, H; Hessel, R; Juying, J; Khatteli, H; Khitrov, N; Kounalaki, A; Laouina, A; Lollino, P; Lopes, M; Magole, L; Medina, L; Mendoza, M; Morais, P; Mulale, K; Ocakoglu, F; Ouessar, M; Ovalle, C; Perez, C; Perkins, J; Pliakas, F; Polemio, M; Pozo, A; Prat, C; Qinke, Y; Ramos, A; Ramos, J; Riquelme, J; Romanenkov, V; Rui, L; Santaloia, F; Sebego, R; Sghaier, M; Silva, N; Sizemskaya, M; Soares, J; Sonmez, H; Taamallah, H; Tezcan, L; Torri, D; Ungaro, F; Valente, S; de Vente, J; Zagal, E; Zeiliguer, A; Zhonging, W; Ziogas, A

2014-11-01

Indicator-based approaches are often used to monitor land degradation and desertification from the global to the very local scale. However, there is still little agreement on which indicators may best reflect both status and trends of these phenomena. In this study, various processes of land degradation and desertification have been analyzed in 17 study sites around the world using a wide set of biophysical and socioeconomic indicators. The database described earlier in this issue by Kosmas and others (Environ Manage, 2013) for defining desertification risk was further analyzed to define the most important indicators related to the following degradation processes: water erosion in various land uses, tillage erosion, soil salinization, water stress, forest fires, and overgrazing. A correlation analysis was applied to the selected indicators in order to identify the most important variables contributing to each land degradation process. The analysis indicates that the most important indicators are: (i) rain seasonality affecting water erosion, water stress, and forest fires, (ii) slope gradient affecting water erosion, tillage erosion and water stress, and (iii) water scarcity soil salinization, water stress, and forest fires. Implementation of existing regulations or policies concerned with resources development and environmental sustainability was identified as the most important indicator of land protection.

Identifying Watershed Regions Sensitive to Soil Erosion and Contributing to Lake Eutrophication--A Case Study in the Taihu Lake Basin (China).

PubMed

Lin, Chen; Ma, Ronghua; He, Bin

2015-12-24

Taihu Lake in China is suffering from severe eutrophication partly due to non-point pollution from the watershed. There is an increasing need to identify the regions within the watershed that most contribute to lake water degradation. The selection of appropriate temporal scales and lake indicators is important to identify sensitive watershed regions. This study selected three eutrophic lake areas, including Meiliang Bay (ML), Zhushan Bay (ZS), and the Western Coastal region (WC), as well as multiple buffer zones next to the lake boundary as the study sites. Soil erosion intensity was designated as a watershed indicator, and the lake algae area was designated as a lake quality indicator. The sensitive watershed region was identified based on the relationship between these two indicators among different lake divisions for a temporal sequence from 2000 to 2012. The results show that the relationship between soil erosion modulus and lake quality varied among different lake areas. Soil erosion from the two bay areas was more closely correlated with water quality than soil erosion from the WC region. This was most apparent at distances of 5 km to 10 km from the lake, where the r² was as high as 0.764. Results indicate that soil erosion could be used as an indicator for identifying key watershed protection areas. Different lake areas need to be considered separately due to differences in geographical features, land use, and the corresponding effects on lake water quality.

Identifying Watershed Regions Sensitive to Soil Erosion and Contributing to Lake Eutrophication—A Case Study in the Taihu Lake Basin (China)

PubMed Central

Lin, Chen; Ma, Ronghua; He, Bin

2015-01-01

Taihu Lake in China is suffering from severe eutrophication partly due to non-point pollution from the watershed. There is an increasing need to identify the regions within the watershed that most contribute to lake water degradation. The selection of appropriate temporal scales and lake indicators is important to identify sensitive watershed regions. This study selected three eutrophic lake areas, including Meiliang Bay (ML), Zhushan Bay (ZS), and the Western Coastal region (WC), as well as multiple buffer zones next to the lake boundary as the study sites. Soil erosion intensity was designated as a watershed indicator, and the lake algae area was designated as a lake quality indicator. The sensitive watershed region was identified based on the relationship between these two indicators among different lake divisions for a temporal sequence from 2000 to 2012. The results show that the relationship between soil erosion modulus and lake quality varied among different lake areas. Soil erosion from the two bay areas was more closely correlated with water quality than soil erosion from the WC region. This was most apparent at distances of 5 km to 10 km from the lake, where the r2 was as high as 0.764. Results indicate that soil erosion could be used as an indicator for identifying key watershed protection areas. Different lake areas need to be considered separately due to differences in geographical features, land use, and the corresponding effects on lake water quality. PMID:26712772

Modulation of erosion rates of uplifting landscapes by long-term climate change: Experimental investigation

NASA Astrophysics Data System (ADS)

Moussirou, Bérangé; Bonnet, Stéphane

2017-04-01

Whether climatic variations play a major role, or not, in setting the erosion rate of continental landscapes is key for demonstrating the influence of climate on the tectonic evolution of mountain belts, as expected from analytical, numerical and analog modelling approaches. These models actually demonstrate that any modification in surface erosion rate that would affect significantly the gravitational loading of the continental crust might change its state of stress and consequently its deformation. However field evidences of these interactions has proved challenging to demonstrate unambiguously, the question of the climatic control on erosion efficiency at the geological time-scale being among the most critical issues. Here, we investigate how a change in precipitation influences the erosional dynamics of a landscape on the basis of an experimental approach where we surveyed the erosion by runoff of water of laboratory-scale landscapes that evolved under the combination of uplift and rainfall forcings (e.g. Bonnet and Crave, 2006). The experimental facility used is a modified of a device initially developed in the Geosciences Rennes laboratory and now set up in the Geosciences Environnement Toulouse laboratory. Following early experiments of Bonnet and Crave (2003) where the effect of a sudden drop in precipitation was investigated, we consider here the impact of decreasing rainfall events of finite duration on the erosive response of a landscape forced by a constant uplift (10 mm/h) and initially at steady-state (SS1). We performed several experiments with the same amplitude (from 160 to 60mm/h) but with different duration of rainfall drop (Tp: 0, 60, 300, 500, 700 min). As predicted theoretically and already observed in numerical and experimental modelling studies, a sudden drop of precipitation rate (Tp=0) induced a decrease of the mean erosion rate of the landscape (E), resulting in surface uplift. Then, landscape mean elevation stabilized to a higher value as it recovered a new steady-state (SS2). On experiments with a gradual (linear) decrease of precipitation of finite duration (Tp>0), we observe that the onset of surface uplift and of decrease in erosion rate is delayed with regard to the onset of precipitation change and occurs only after a period where landscapes remain very close steady-state. The duration of this delay differs between experiments and increases linearly with Tp. Beyond this delay, the mean erosion rate then drops to a minimum value, while knickpoints migrate in the drainage system following the mechanism described by Whipple and Tucker (1999). We observe that the amplitude of the drop in mean erosion rate decreases with Tp, experiments with the longest duration of precipitation drop showing a damped erosional response, representing only about 20 % the uplift rate value (Tp=700 min). As a perspective we anticipate that experiments with longer Tp would ultimately not show any significant erosional response to precipitation variations.

The SfM-monitored rill experiment, a tool to detect decisive processes?

NASA Astrophysics Data System (ADS)

Remke, Alexander-André; Wirtz, Stefan; Brings, Christine; Gronz, Oliver; Seeger, Manuel; Ries, Johannes B.

2016-04-01

The initiation of rill erosion marks the transition from sheet to linear erosion. With this transition, the relevant processes change and therefore, the observation method needs to be changed too: from observing rainfall induced drop impacts to hydraulic observations. For us, the investigation of the decisive processes in eroding rills resulted in a constantly revised and updated rill erosion experiment, that has been used for several years. Within this experiment the sediment transport behavior of rills is simulated and examined. To make the experiment repeatable and replicable, several key-variables have to be kept constant, i.e. water quantity (1000 L), test duration (approx. 4 min.) and the length of the tested rill section (20 m). For each tested rill, the topographic background is determined i.e. catchment area, aspect, slope, position and height of existing knick-points and three cross-sections. After the initial assessment, the rill is flushed with water (250 L min -1) twice in order to determine the modifications of the rill caused by the flowing water. Within these approx. 4 minutes of "controlled destruction" the velocity of the turbulently flowing water at the beginning of the erosional event and after one and two minutes is determined and the corresponding water depth is recorded using three gauges at selected measuring points. At the end of the tested rill segment, the discharge is constantly monitored. Unfortunately, the results of this rill experiment do not directly show the modifications caused by the artificial waterflow. A way out of this knowledge gap is offered by combining this experimental measurement method with a technique already used in different scientific disciplines in more large-scale applications. Structure-from-Motion technology offers the opportunity to get a different, more detailed view inside the erosion rills. A static multi-camera-array and a dynamically moved digital video-frame camera are now used to obtain three-dimensional models of the rills before and after the experiment. These 3-D-models allow, in close connection with the time-controlled sampling, to point out the spatial and temporal distribution of erosion and accumulation hotspots. Furthermore it becomes possible to strike the erosion/accumulation-balance and get a glimpse at the hot-spots of side-wall-failure and rill bed-incision. The combination of both approaches - rill experiment and 3D modells - results in a more comprehensive insight: What happens in the rill? They allow for the detailed observation of the position, magnitude and furthermore the identification of the relevant erosion process. Eventually, the increased knowledge will assist to describe the processes accurately in a mathematical-physical way.

The role of carbon dust emission as a global source of atmospheric CO2

USDA-ARS?s Scientific Manuscript database

Soil erosion redistributes soil organic carbon (SOC) within terrestrial ecosystems, to the atmosphere and oceans. Dust export is an essential component of the carbon (C) and carbon dioxide (CO2) budget, because wind erosion contributes to the C cycle by selectively removing4 SOC from vast areas and ...

Soil organic carbon dust emission: an omitted global source of atmospheric CO2?

USDA-ARS?s Scientific Manuscript database

Soil erosion redistributes soil organic carbon (SOC) within terrestrial ecosystems, to the atmosphere and oceans. Dust export is an essential component of the carbon (C) and carbon dioxide (CO2) budget because wind erosion contributes to the C cycle by removing selectively SOC from vast areas and tr...

Food acid content and erosive potential of sugar-free confections.

PubMed

Shen, P; Walker, G D; Yuan, Y; Reynolds, C; Stacey, M A; Reynolds, E C

2017-06-01

Dental erosion is an increasingly prevalent problem associated with frequent consumption of acidic foods and beverages. The aim of this study was to measure the food acid content and the erosive potential of a variety of sugar-free confections. Thirty sugar-free confections were selected and extracts analysed to determine pH, titratable acidity, chemical composition and apparent degree of saturation with respect to apatite. The effect of the sugar-free confections in artificial saliva on human enamel was determined in an in vitro dental erosion assay using change in surface microhardness. The change in surface microhardness was used to categorize the confections as high, moderate or low erosive potential. Seventeen of the 30 sugar-free confections were found to contain high concentrations of food acids, exhibit low pH and high titratable acidity and have high erosive potential. Significant correlations were found between the dental erosive potential (change in enamel surface microhardness) and pH and titratable acidity of the confections. Ten of these high erosive potential confections displayed dental messages on the packaging suggesting they were safe for teeth. Many sugar-free confections, even some with 'Toothfriendly' messages on the product label, contain high contents of food acids and have erosive potential. © 2017 Australian Dental Association.

The use of color infrared photography for wetlands assessment

NASA Technical Reports Server (NTRS)

Enslin, W. R.; Sullivan, M. C.

1974-01-01

A study was undertaken of Pointe Mouillee Marsh, located on Lake Erie, to assess shoreline erosion and to inventory and evaluate adjacent land as potential replacement for areas lost to erosion, and to provide better data sources for management decisions. The results of the study were: (1) Evaluation of low altitude oblique photography was useful in determining specifications of operational mission requirements; (2) Accurate base map revisions, reflecting shoreline erosion, were made using aerial photography and a Zoom Transfer Scope; (3) An aerial land cover inventory provided data necessary for the selection of adjacent lands suitable for marshland development; (4) A detailed inventory of vegetative communities (mapped from CIR), was made for management decisions; and (5) A carefully selected and well laid-out transect was a key asset to photo interpretation and analysis of vegetation.

Predicting risk of rill initiation in a sub-catchment of Lake Balaton, Hungary

NASA Astrophysics Data System (ADS)

Hausner, C.; Sisák, I.

2009-04-01

Rill erosion is an accelerated form of soil degradation. It removes much more soil and nutrients from the agricultural land than sheet erosion. Soils in the southern sub-watershed of Lake Balaton are especially prone to rill erosion and they contribute to siltation of ditches, to muddy floods and to eutrofication of the lake. The parent material in this region is mainly (sandy) loess and the soils are already moderately or strongly eroded thus, the low tolerance of loess against erosion determines erodibility. Identification of soils with high risk of rill erosion is crucial to plan mitigation measures. Soil erodibility has been investigated in this study in the catchment of Tetves stream. The USLE soil erodibility factor and soil slaking are widely accepted indicators for soil erosion. Both of them are published for all soil texture classes in handbooks of soil mapping. We have found that erodibility derived from our physical model has a close linear correlation with the product of the USLE soil erodibility factor and soil slaking grade thus, USLE could be directly used to assess parameters for physical based models. Rill erosion is highly probable if the product of KUSLE X slaking grade is above 2. Digital maps were produced to delineate soils with high potential for rill erosion. The basic data for the soil properties were drawn from the 1:10,000 soil map. Soil texture classes were used to assign KUSLE and slaking grade to the soil units. Beyond soil properties, other factors also influence rill formation: slope, surface cover, rainfall intensity. However, identifying soil properties, which make soils prone to rill erosion, is an important initial step for the reduction of diffuse agricultural loads to Lake Balaton. It might be the objective of River Basin Management Plans in the Water Framework Directive to prevent rill erosion and our study provides scientific evidence for targeting this policy.

Study of erosion characterization of carbon fiber reinforced composite material

NASA Astrophysics Data System (ADS)

Debnath, Uttam Kumar; Chowdhury, Mohammad Asaduzzaman; Kowser, Md. Arefin; Mia, Md. Shahin

2017-06-01

Carbon fiber composite materials are widely used at different engineering and industrial applications there are good physical, mechanical, chemical properties and light weight. Erosion behavior of materials depends on various factors such as impact angle, particle velocity, particle size, particle shape, particle type, particle flux, temperature of the tested materials. Among these factors impact angle and particle velocity have been recognized as two parameters that noticeably influence the erosion rates of all tested materials. Irregular shaped sand (SiO2) particles of various sizes (200-300 µm, 400-500 µm, and 500-600 µm) were selected erosive element. Tested conditions such as impingement angles between 15 degree to 90 degree, impact velocities between 30-50 m/sec, and stand-off distances 15-25 mm at surrounding room temperature were maintained. The highest level of erosion of the tested composite is obtained at 60° impact angle, which signifies the semi-ductile behavior of this material. Erosion showed increasing trend with impact velocity and decreasing nature in relation to stand-off distance. Surface damage was analyzed using SEM to examine the nature of the erosive wear mechanism.

Searching for plant root traits to improve soil cohesion and resist soil erosion

NASA Astrophysics Data System (ADS)

De Baets, Sarah; Smyth, Kevin; Denbigh, Tom; Weldon, Laura; Higgins, Ben; Matyjaszkiewicz, Antoni; Meersmans, Jeroen; Chenchiah, Isaac; Liverpool, Tannie; Quine, Tim; Grierson, Claire

2017-04-01

Soil erosion poses a serious threat to future food and environmental security. Soil erosion protection measures are therefore of great importance for soil conservation and food security. Plant roots have proven to be very effective in stabilizing the soil and protecting the soil against erosion. However, no clear insights are yet obtained into the root traits that are responsible for root-soil cohesion. This is important in order to better select the best species for soil protection. Research using Arabidopsis mutants has made great progress towards explaining how root systems are generated by growth, branching, and responses to gravity, producing mutants that affect root traits. In this study, the performance of selected Arabidopsis mutants is analyzed in three root-soil cohesion assays. Measurements of detachment, uprooting force and soil detachment are here combined with the microscopic analysis of root properties, such as the presence, length and density of root hairs in this case. We found that Arabidopsis seedlings with root hairs (wild type, wer myb23, rsl4) were more difficult to detach from gel media than hairless (cpc try) or short haired (rsl4, rhd2) roots. Hairy roots (wild type, wer myb23) on mature, non-reproductive rosettes were more difficult to uproot from compost or clay soil than hairless roots (cpc try). At high root densities, erosion rates from soils with hairless roots (cpc try) were as much as 10 times those seen from soils occupied by roots with hairs (wer myb23, wild type). We find therefore root hairs play a significant role in root-soil cohesion and in minimizing erosion. This framework and associated suite of experimental assays demonstrates its ability to measure the effect of any root phenotype on the effectiveness of plant roots in binding substrates and reducing erosion.

Climatic vs. tectonic control on glacial relief

NASA Astrophysics Data System (ADS)

Prasicek, Günther; Herman, Frederic; Robl, Jörg

2017-04-01

The limiting effect of a climatically-induced glacial buzz-saw on the height of mountain ranges has been extensively discussed in the geosciences. The buzz-saw concept assumes that solely climate controls the amount of topography present above the equilibrium line altitude (ELA), while the rock uplift rate plays no relevant role. This view is supported by analyses of hypsometric patterns in orogens worldwide. Furthermore, numerical landscape evolution models show that glacial erosion modifies the hypsometry and reduces the overall relief of mountain landscapes. However, such models often do not incorporate tectonic uplift and can only simulate glacial erosion over a limited amount of time, typically one or several glacial cycles. Constraints on glacial end-member landscapes from analytical, time-independent models are widely lacking. Here we present a steady-state solution for a glacier equilibrium profile in an active orogen modified from the mathematical conception presented by Headley et al. (2012). Our approach combines a glacial erosion law with the shallow ice approximation, specifically the formulations of ice sliding and deformation velocities and ice flux, to calculate ice surface and bed topography from prescribed specific mass balance and rock uplift rate. This solution allows the application of both linear and non-linear erosion laws and can be iteratively fitted to a predefined gradient of specific mass balance with elevation. We tested the influence of climate (fixed rock uplift rate, different ELAs) and tectonic forcing (fixed ELA, different rock uplift rates) on steady-state relief. Our results show that, similar to fluvial orogens, both climate and rock uplift rate exert a strong influence on glacial relief and that the relation among rock uplift rate and relief is governed by the glacial erosion law. This finding can provide an explanation for the presence of high relief in high latitudes. Headley, R.M., Roe, G., Hallet, B., 2012. Glacier longitudinal profiles in regions of active uplift. Earth and Planetary Science Letters, 317-318, 354-362.

Electrode erosion properties of gas spark switches for fast linear transformer drivers

NASA Astrophysics Data System (ADS)

Li, Xiaoang; Pei, Zhehao; Zhang, Yuzhao; Liu, Xuandong; Li, Yongdong; Zhang, Qiaogen

2017-12-01

Fast linear transformer drivers (FLTDs) are a popular and potential route for high-power devices employing multiple "bricks" in series and parallel, but they put extremely stringent demands on gas switches. Electrode erosion of FLTD gas switches is a restrictive and unavoidable factor that degrades performance and limits stability. In this paper, we systematically investigated the electrode erosion characteristics of a three-electrode field distortion gas switch under the typical working conditions of FLTD switches, and the discharge current was 7-46 kA with 46-300 ns rise time. A high speed frame camera and a spectrograph were used to capture the expansion process and the spectral emission of the spark channel was used to estimate the current density and the spark temperature, and then the energy fluxes and the external forces on the electrode surface were calculated. A tens of kilo-ampere nanosecond pulse could generate a 1011 W/m2 energy flux injection and 1.3-3.5 MPa external pressure on the electrode surface, resulting in a millimeter-sized erosion crater with the maximum peak height Rz reaching 100 μm magnitude. According to the morphological images by a laser scanning confocal microscope, the erosion crater of a FLTD switch contained three kinds of local morphologies, namely a center boiling region, an overflow region and a sputtering region. In addition, the crater size, the surface roughness, and the mass loss were highly dependent on the current amplitude and the transferred charge. We also observed Morphology Type I and Type II, respectively, with different pulse parameters, which had an obvious influence on surface roughness and mass loss. Finally, the quantitative relationship between the electrode mass loss and the pulse parameter was clarified. The transferred charge and the current amplitude were proved to be the main factors determining the electrode mass loss of a FLTD switch, and a least squares fitting expression for mass loss was also obtained.

Quantifying gully erosion contribution from morphodynamic analysis of historical aerial photographs in a large catchment SW Spain

NASA Astrophysics Data System (ADS)

Hayas, Antonio; Giráldez, Juan V.; Laguna, Ana; Peña, Peña; Vanwalleghem, Tom

2015-04-01

Gully erosion is widely recognized as an important erosion process and source of sediment, especially in Mediterranean basins. Recent advances in monitoring techniques, such as ground-based LiDAR, drone-bounded cameras or photoreconstruction, allow quantifying gully erosion rates with unprecedented accuracy. However, many studies only focus on gully growth during a short period. In agricultural areas, farmers frequently erase gullies artificially. Over longer time scales, this results in an important dynamic of gully growth and infilling. Also, given the significant temporal variability of precipitation, land use and the proper gully erosion processes, gully growth is non-linear over time. This study therefore aims at analyzing gully morphodynamics over a long time scale (1957-2011) in a large catchment in order to quantify gully erosion processes and its contribution to overall sediment dynamics. The 20 km2 study area is located in SW Spain. The extension of the gully network was digitized by photographic interpretation based on aerial photographs from 1957, 1981, 1985, 1999, 2002, 2005, 2007, 2009 and 2011. Gully width was measured at representative control points for each of these years. During this period, the dominant land use changed considerably from herbaceous crops to olive orchards. A field campaign was conducted in 2014 to measure current gully width and depth. Total gully volume and uncertainty was determined by Monte Carlo-based simulations of gully cross-sectional area for unmeasured sections. The extension of the gully network both increased and decreased in the study period. Gully density varied between 1.93 km km-2 in 1957, with a minimum of 1.37 km km-2 in 1981 and a maximum of 5.40 km km-2 in 2011. Gully width estimated in selected points from the orthophotos range between 0.9 m and 59.2 m, and showed a good lognormal fit. Field campaigns results in a collection of cross-section measures with gullies widths between 1.87 and 28.5 m and depths from 0.55 m to 5.02 m. A gully width-depth relation was established according to a logarithm expression with an overall r2 of 0.82. As no historical information on gully depth was available, this relation was assumed to be constant over time. Monte Carlo simulation was then used to generate width and depth values for the different gully segments, based on different lognormal distributions fitted to the estimated gully widths from 1957-2011 and on the width-depth regression. The calculated mean gully volume between 1953 and 2011 varied between 145.103 m3 and 2454.103 m3. The contribution of gully erosion to the overall sediment budget was found to be relatively stable between 1957-2008 with a mean value of 11.2 ton ha-1 year-1, while in the period 2008-2011 which includes frequent rainy days winter resulted in a mean value of 604 ton ha-1 year-1. Uncertainty estimates by Monte Carlo place the estimated contribution of gully erosion for this last period between 523-694 ton ha-1 year-1. The relation between gully erosion rates and driving factors such as land use change and rainfall was analysed in order to explain this variation. The high gully erosion rates of the period 2008-2011 could be linked to extreme rainfall events. This study has determined gully erosion rates with a high temporal resolution over several decades. The results show that gully erosion rates are highly variable and therefore that a simple interpolation between the start and end date would highly underestimate gully contribution during certain years, such as for example between 2005-2011. Overall, gully erosion is shown to be an important process of sediment generation in Mediterranean basins.

Suppressed gross erosion of high-temperature lithium via rapid deuterium implantation

DOE PAGES

Abrams, T.; Jaworski, M. A.; Chen, M.; ...

2015-12-17

Lithium-coated high-Z substrates are planned for use in the NSTX-U divertor and are a candidate plasma facing component (PFC) for reactors, but it remains necessary to characterize the gross Li erosion rate under high plasma fluxes (>10 23 m -2 s -1), typical for the divertor region. In this work, a realistic model for the compositional evolution of a Li/D layer is developed that incorporates first principles molecular dynamics (MD) simulations of D diffusion in liquid Li. Predictions of Li erosion from a mixed Li/D material are also developed that include formation of lithium deuteride (LiD). The erosion rate ofmore » Li from LiD is predicted to be significantly lower than from pure Li. This prediction is tested in the Magnum-PSI linear plasma device at ion fluxes of 10 23-10 24 m -2 s -1 and Li surface temperatures. ≤800 °C. Li/LiD coatings ranging in thickness from 0.2 to 500 μm are studied. The dynamic D/Li concentrations are inferred via diffusion simulations. The pure Li erosion rate remains greater than Langmuir Law evaporation, as expected. For mixed-material Li/LiD surfaces, the erosion rates are reduced, in good agreement with modelling in almost all cases. Lastly, these results imply that the temperature limit for a Li-coated PFC may be significantly higher than previously imagined.« less

Assessment of Tooth Wear Among Glass Factory Workers: WHO 2013 Oral Health Survey.

PubMed

Chaturvedi, Pulkit; Bhat, Nagesh; Asawa, Kailash; Tak, Mridula; Bapat, Salil; Gupta, Vivek Vardhan

2015-08-01

Glass factory workers are often exposed to the hazardous environment that leads to deleterious oral health and subsequently, general health. We planned to determine the effects of the particulates present in the milieu on the tooth wear among workers. To assess tooth wear among glass factory workers in Jaipur, Rajasthan, India. A descriptive cross-sectional survey was conducted among 936 glass workers in Jaipur, Rajasthan, India from January-June 2014. A survey proforma was designed for tooth wear evaluation with the help of WHO Oral Health Assessment form 2013 (for adults). Information regarding oral health practices, adverse habits and dietary habits, demographic details was gathered and clinical parameters were recorded. The Chi-square test, t-test, One-way Analysis of Variance and a Stepwise multiple linear regression analysis. The most prevalent form of erosion was enamel erosion (589, 62.93%) with few subjects of deeper dentinal erosion and the difference was statistically significant (p=0.001). Dental erosion was found to be higher among males compared to females. Years of experience and educational status were identified as best predictors for dental erosion. It was concluded that there was considerable evidence of dental erosion found among the factory workers. Due to ignorance on social, cultural and health aspects, professional approach with regular dental care services for detection of early symptoms and planning of preventive strategies is warranted.

An Analytical Model for Basin-scale Glacier Erosion as a Function of Climate and Topography

NASA Astrophysics Data System (ADS)

Jaffrey, M.; Hallet, B.

2017-12-01

Knowledge about glacier erosion has advanced considerably over the last few decades with the emergence of a firm mechanistic understanding of abrasion and quarrying, the growing sophistication of complex numerical models of glacial erosion and the evolution of glacial landforms, and the increase in data from field studies of erosion rates. Interest in glacial erosion has also intensified and diversified substantially as it is increasingly recognized as a key process affecting the heights of mountains, the overall evolution of mountain belts, and the coupling of climate, erosion, and tectonics. Yet, the general controls of glacier erosion rates have not been addressed theoretically, and the large range of published basin-scale erosion rates, covering more than 3 orders of magnitude, remains poorly understood. To help gain insight into glacier erosion rates at the scale of glacier basins, the only scale for which extensive data exist, we develop analytically a simple budget of the total mechanical energy per unit time, the power, dissipated by a steady state glacier in sliding, S, and viscous deformation, V. We hypothesize that the power for the work of erosion derives solely from S and that the basin wide erosion rate scales with S averaged over the basin. We solve the power budget directly in terms of climatic and topographic parameters, showing explicitly that the source of power to drive both S and V is the gravitational power supplied by the net snow accumulation (mass balance). The budget leads to the simple metric φ=mbΔz2 for the basin average of S with Δz being the glacier basin relief and mb the gradient of the mass balance with elevation. The dependence of φ on the square of the relief arises from both the mass balance's and potential energy's linear increases with elevation. We validate φ using results from a comprehensive field study of erosion rates paired with glaciological data along a transect extending from Southern Patagonia to the Antarctic Peninsula (Koppes et al. 2015. Nature, 526(7571), 100). Along this transect, φ accounts for 75% ± 12% of the variation in reported erosion rates. The power budget model illuminates the role of climate and topography in basin scale erosion rates with direct implications for the broad community interested in ice masses and their interconnections with climate and topography.

Rainfall and Erosion Response Following a Southern California Wildfire

NASA Astrophysics Data System (ADS)

Wohlgemuth, P. M.; Robichaud, P. R.; Brown, R. E.

2011-12-01

Wildfire renders landscapes susceptible to flooding and accelerated surface erosion. Consumption of the vegetation canopy and the litter or duff layer removes resistances to the agents of erosion. Moreover, changes in soil properties can restrict infiltration, increasing the effectiveness of the driving forces of rainsplash and surface runoff. However, it is unclear whether surface erosion varies linearly with rainfall amounts and intensities or if thresholds exist beyond which erosion increases in a different trajectory. The Santiago Fire burned over 11000 ha in northeastern Orange County, California in October 2007. The burn area consists of a deeply dissected mountain block underlain by sedimentary and metamorphic rocks that produce erosive soils. Regional erosion and sediment transport is triggered by winter cyclonic storms. Recording raingages were deployed across a vertical gradient within the burned area and silt fences were constructed to monitor hillslope erosion. During the study period initial storms were characterized by moderate rainfall (amounts less than 25 mm with peak 10-minute intensities of less than 10 mm per hr). Surface erosion was concomitantly minor, less than 0.4 Mg per ha. However, an unusual thunderstorm in late May 2008 produced spatially variable rainfall and consequent surface erosion across the study area. The raingage at a lower elevation site measured 41.4 mm of rain for this storm with a peak 10-minute intensity of 81 mm per hr. The silt fences were overtopped, yielding a minimum value of 18.5 Mg per ha. In contrast, the raingage at an upper elevation site recorded 19.6 mm of rain with a peak 10-minute intensity of 50 mm per hr. Surface erosion in the higher elevation sites was negligible (0.1 Mg per ha). Subsequently, individual storms exceeded 100 mm of rainfall but peak 10-minute intensities never approached those of the May thunderstorm. Erosion was moderate (mostly less than 5 Mg per ha), albeit influenced by the presence of regrowing vegetation. We therefore believe that surface erosion in the immediate postfire environment is more related to storm intensity than rainfall amount. Even allowing for site-to-site differences and site changes over the first postfire winter season, it is clear that some threshold in erosion response was crossed at the lower elevation sites during the May 2008 thunderstorm. We suggest that this represents a threshold of peak 10-minute intensity of between 50 and 80 mm per hr.

Assessment of soil erosion risk in Komering watershed, South Sumatera, using SWAT model

NASA Astrophysics Data System (ADS)

Salsabilla, A.; Kusratmoko, E.

2017-07-01

Changes in land use watershed led to environmental degradation. Estimated loss of soil erosion is often difficult due to some factors such as topography, land use, climate and human activities. This study aims to predict soil erosion hazard and sediment yield using the Soil and Water Assessment Tools (SWAT) hydrological model. The SWAT was chosen because it can simulate the model with limited data. The study area is Komering watershed (806,001 Ha) in South Sumatera Province. There are two factors land management intervention: 1) land with agriculture, and 2) land with cultivation. These factors selected in accordance with the regulations of spatial plan area. Application of the SWAT demonstrated that the model can predict surface runoff, soil erosion loss and sediment yield. The erosion risk for each watershed can be classified and predicted its changes based on the scenarios which arranged. In this paper, we also discussed the relationship between the distribution of erosion risk and watershed's characteristics in a spatial perspective.

Quantitative genetic properties of four measures of deformity in yellowtail kingfish Seriola lalandi Valenciennes, 1833.

PubMed

Nguyen, N H; Whatmore, P; Miller, A; Knibb, W

2016-02-01

The main aim of this study was to estimate the heritability for four measures of deformity and their genetic associations with growth (body weight and length), carcass (fillet weight and yield) and flesh-quality (fillet fat content) traits in yellowtail kingfish Seriola lalandi. The observed major deformities included lower jaw, nasal erosion, deformed operculum and skinny fish on 480 individuals from 22 families at Clean Seas Tuna Ltd. They were typically recorded as binary traits (presence or absence) and were analysed separately by both threshold generalized models and standard animal mixed models. Consistency of the models was evaluated by calculating simple Pearson correlation of breeding values of full-sib families for jaw deformity. Genetic and phenotypic correlations among traits were estimated using a multitrait linear mixed model in ASReml. Both threshold and linear mixed model analysis showed that there is additive genetic variation in the four measures of deformity, with the estimates of heritability obtained from the former (threshold) models on liability scale ranging from 0.14 to 0.66 (SE 0.32-0.56) and from the latter (linear animal and sire) models on original (observed) scale, 0.01-0.23 (SE 0.03-0.16). When the estimates on the underlying liability were transformed to the observed scale (0, 1), they were generally consistent between threshold and linear mixed models. Phenotypic correlations among deformity traits were weak (close to zero). The genetic correlations among deformity traits were not significantly different from zero. Body weight and fillet carcass showed significant positive genetic correlations with jaw deformity (0.75 and 0.95, respectively). Genetic correlation between body weight and operculum was negative (-0.51, P < 0.05). The genetic correlations' estimates of body and carcass traits with other deformity were not significant due to their relatively high standard errors. Our results showed that there are prospects for genetic selection to improve deformity in yellowtail kingfish and that measures of deformity should be included in the recording scheme, breeding objectives and selection index in practical selective breeding programmes due to the antagonistic genetic correlations of deformed jaws with body and carcass performance. © 2015 John Wiley & Sons Ltd.

Drywall stilt dermatosis.

PubMed

Lewis, E J; Prawer, S E; Crutchfield, C E

1996-12-01

We describe a previously unreported occupational dermatosis occurring in a worker employed in drywall installation and finishing. This 50-year-old man presented with bilaterally symmetrical, parallel, linear crusted erosions on his anteromedial legs after wearing drywall stilts. The pathophysiology of this condition is considered.

The Relationship Between Focal Erosions and Generalized Osteoporosis in Postmenopausal Women with Rheumatoid Arthritis: The Osteoporosis in Rheumatoid Arthritis (OPiRA) Cohort Study

PubMed Central

Solomon, Daniel H.; Finkelstein, Joel S.; Shadick, Nancy; LeBoff, Meryl S; Winalski, Carl; Stedman, Margaret; Glass, Roberta; Brookhart, M. Alan; Weinblatt, Michael E.; Gravallese, Ellen M.

2009-01-01

Background After 10 years of RA, more than half of patients have focal erosions and the risk of fracture is doubled. However, little information exists about the potential relationship between focal erosions and BMD. Methods We enrolled 163 postmenopausal women with RA who did not use osteoporosis medications. Participants underwent a DXA test at the hip and spine, hand x-rays, and answered a questionnaire. The hand x-rays were scored using the Sharp method. We examined the relationship between BMD and erosions using Spearman correlation coefficients and adjusted linear regression models. Results The 163 postmenopausal women had an average duration of RA of 13.7 years and almost all patients were currently using a DMARD. 63% were RF positive, the median mHAQ score was 0.7, and the average DAS-28 was 3.8. The erosion score was significantly correlated with the total hip BMD (Spearman R = −0.33, p < 0.0001) but not with the lumbar spine BMD (Spearman R = −0.09, p = 0.27). Hip BMD was significantly lower in RF positive women versus RF negative women (p = 0.02). In multivariable models that included age, BMI, and cumulative oral glucocorticoid dosage, neither total hip nor spine BMD were significantly associated with focal erosions. Conclusion These results suggest that hip BMD is associated with focal erosions among postmenopausal women with RA, but that this association disappears after multivariate adjustment. While BMD and erosions may be correlated bone manifestations of RA, their relationship is complex and influenced by other disease-related factors. PMID:19479876

Soil property effects on wind erosion of organic soils

NASA Astrophysics Data System (ADS)

Zobeck, Ted M.; Baddock, Matthew; Scott Van Pelt, R.; Tatarko, John; Acosta-Martinez, Veronica

2013-09-01

Histosols (also known as organic soils, mucks, or peats) are soils that are dominated by organic matter (OM > 20%) in half or more of the upper 80 cm. Forty two states have a total of 21 million ha of Histosols in the United States. These soils, when intensively cropped, are subject to wind erosion resulting in loss of crop productivity and degradation of soil, air, and water quality. Estimating wind erosion on Histosols has been determined by USDA-Natural Resources Conservation Service (NRCS) as a critical need for the Wind Erosion Prediction System (WEPS) model. WEPS has been developed to simulate wind erosion on agricultural land in the US, including soils with organic soil material surfaces. However, additional field measurements are needed to understand how soil properties vary among organic soils and to calibrate and validate estimates of wind erosion of organic soils using WEPS. Soil properties and sediment flux were measured in six soils with high organic contents located in Michigan and Florida, USA. Soil properties observed included organic matter content, particle density, dry mechanical stability, dry clod stability, wind erodible material, and geometric mean diameter of the surface aggregate distribution. A field portable wind tunnel was used to generate suspended sediment and dust from agricultural surfaces for soils ranging from 17% to 67% organic matter. The soils were tilled and rolled to provide a consolidated, friable surface. Dust emissions and saltation were measured using an isokinetic vertical slot sampler aspirated by a regulated suction source. Suspended dust was sampled using a Grimm optical particle size analyzer. Particle density of the saltation-sized material (>106 μm) was inversely related to OM content and varied from 2.41 g cm-3 for the soil with the lowest OM content to 1.61 g cm-3 for the soil with highest OM content. Wind erodible material and the geometric mean diameter of the surface soil were inversely related to dry clod stability. The effect of soil properties on sediment flux varied among flux types. Saltation flux was adequately predicted with simple linear regression models. Dry mechanical stability was the best single soil property linearly related to saltation flux. Simple linear models with soil properties as independent variables were not well correlated with PM10E values (mass flux). A second order polynomial equation with OM as the independent variable was found to be most highly correlated with PM10E values. These results demonstrate that variations in sediment and dust emissions can be linked to soil properties using simple models based on one or more soil properties to estimate saltation mass flux and PM10E values from organic and organic-rich soils.

Analysis of the deconstruction of Dyke Marsh, George Washington Memorial Parkway, Virginia-Progression, geologic and manmade causes, and effective restoration scenarios

USGS Publications Warehouse

Litwin, Ronald J.; Smoot, Joseph P.; Pavich, Milan J.; Markewich, Helaine W.; Oberg, Erik; Helwig, Ben; Steury, Brent; Santucci, Vincent L.; Durika, Nancy J.; Rybicki, Nancy B.; Engelhardt, Katharina M.; Sanders, Geoffrey; Verardo, Stacey; Elmore, Andrew J.; Gilmer, Joseph

2011-01-01

Photoanalysis of time-sequence aerial photographs of Dyke Marsh enabled us to calculate shoreline erosion estimates for this marsh over 19 years (1987-2006), as well as to quantify overall marsh acreage for 6 calendar years spanning an ~70 year interval (1937-2006). Photo overlay of a historic map enabled us to extend our whole-marsh acreage calculations back to 1883. Both sets of analyses were part of a geologic framework study in support of current efforts by the National Park Service (NPS) to restore this urban wetland. Two time intervals were selected for our shoreline erosion analyses, based on image quality and availability: 1987 to 2002, and 2002 to 2006. The more recent time interval shows a marked increase in erosion in the southern part of Dyke Marsh, following a wave-induced breach of a small peninsula that had protected its southern shoreline. Field observations and analyses of annual aerial imagery between 1987 and 2006 revealed a progressive increase in wave-induced erosion that presently is deconstructing Hog Island Gut, the last significant tidal creek network within the Dyke Marsh. These photo analyses documented an overall average westward shoreline loss of 6.0 to 7.8 linear feet per year along the Potomac River during this 19-year time interval. Additionally, photographic evidence documented that lateral erosion now is capturing existing higher order tributaries in the Hog Island Gut. Wave-driven stream piracy is fragmenting the remaining marsh habitat, and therefore its connectivity, relatively rapidly, causing the effective mouth of the Hog Island Gut tidal network to retreat headward visibly over the past several decades. Based on our estimates of total marsh area in the Dyke Marsh derived from 1987 aerial imagery, as much as 12 percent of the central part of the marsh has eroded in the 19 year period we studied (or ~7.5 percent of the original ~78.8 acres of 1987 marshland). Shoreline loss estimates for marsh parcels north and south of our study area have not yet been analyzed, although annual aerial photos from 1987 to 2002 confirm visible progressive shoreline loss in those areas over this same time interval.

Assessment of mercury erosion by surface water in Wanshan mercury mining area.

PubMed

Dai, ZhiHui; Feng, Xinbin; Zhang, Chao; Shang, Lihai; Qiu, Guangle

2013-08-01

Soil erosion is a main cause of land degradation, and in its accelerated form is also one of the most serious ecological environmental problems. Moreover, there are few studies on migration of mercury (Hg) induced by soil erosion in seriously Hg-polluted districts. This paper selected Wanshan Hg mining area, SW China as the study area. Revised universal soil loss equation (RUSLE) and Geographic information system (GIS) methods were applied to calculate soil and Hg erosion and to classify soil erosion intensity. Our results show that the soil erosion rate can reach up to 600,884tkm(-2)yr(-1). Surfaces associated with very slight and extremely severe erosion include 76.6% of the entire land in Wanshan. Furthermore, the cumulative erosion rates in the area impacted by extremely severe erosion make up 90.5% of the total. On an annual basis, Hg surface erosion load was predicted to be 505kgyr(-1) and the corresponding mean migration flux of Hg was estimated to be 3.02kgkm(-2)yr(-1). The erosion loads of Hg resulting from farmland and meadow soil were 175 and 319kgyr(-1) respectively, which were enhanced compared to other landscape types due to the fact that they are generally located in the steep zones associated with significant reclamation. Contributing to establish a mass balance of Hg in Wanshan Hg mining area, this study supplies a dependable scientific basis for controlling soil and water erosion in the local ecosystems. Land use change is the most effective way for reducing Hg erosion load in Wanshan mining area. Copyright © 2013 Elsevier Inc. All rights reserved.

Microscopic investigation of cavitation erosion damage in metals

NASA Technical Reports Server (NTRS)

Hackworh, J. V.; Adler, W. F.

1974-01-01

The results of research to identify the cavitation erosion damage mechanisms at the microscopic level for three metals (aluminum, stainless steel, and titanium) representing a range of properties and microstructure are presented. The metals were exposed to cavitation generated in distilled water by a 20-kHz ultrasonic facility operating at a vibration amplitude of 2 mils. Representative properties of the metals and experimental details are summarized. Replicas of the eroded surfaces of the specimens obtained periodically during exposure were examined with a transmission electron microscope to follow progression of the erosion damage and identify dominant erosion mechanisms as a function of exposure time. Eroded surfaces of selected specimens were also examined with a scanning electron microscope to assist in the interpretation.

The "Knife-Cut Sign" Revisited: A Distinctive Presentation of Linear Erosive Herpes Simplex Virus Infection in Immunocompromised Patients.

PubMed

Cohen, Philip R

2015-10-01

The "knife-cut sign" is a distinctive presentation of linear erosive herpes simplex virus infection in immunocompromised patients. To describe a man whose herpes simplex virus infection-related skin lesions demonstrated the "knife-cut sign" and to review the characteristics of reported immunosuppressed individuals with "knife-cut" cutaneous herpes simplex virus lesions. A man with multiple myeloma and post-stem cell transplant cutaneous graft-versus-host disease managed with systemic prednisone and sirolimus developed disseminated cutaneous herpes simplex virus infection with virus-associated linear ulcers of the inguinal folds and the area between his ear and scalp; the lesions at both sites had a distinctive "knife-cut" appearance. Using the PubMed database, an extensive literature search was performed on herpes simplex virus, immunocompromised patient, and "knife-cut sign". Herpes simplex virus infection-associated skin lesions that demonstrate the "knife-cut sign" present in patients who are immunosuppressed secondary to either an underlying medical condition or a systemic therapy or both. The distinctive virus-related cutaneous lesions appear as linear ulcers and fissures in intertriginous areas, such as the folds in the inguinal area, the vulva, and the abdomen; in addition, other sites include beneath the breast, within the gluteal cleft, and the area between the ear and the scalp. Not only herpes simplex virus-2, but also herpes simplex virus-1 has been observed as the causative viral serotype; indeed, herpes simplex virus-1 has been associated with genital and inframammary lesions in addition to those above the neck. Direct fluorescent antibody testing is a rapid method for confirming the clinically suspected viral infection; however, since false-negative direct fluorescent antibody testing occurred in some of the patients, it may be prudent to also perform viral cultures and possibly lesional skin biopsies to establish the diagnosis. The herpes simplex virus infection-related skin lesions clinically improve once systemic antiviral therapy is initiated. In immunosuppressed individuals, the "knife-cut sign" is a distinctive presentation of cutaneous linear erosive herpes simplex virus infection. Recognition of the linear ulcers in intertriginous areas and body folds should prompt the clinician to consider herpes simplex virus infection-associated skin lesions in an immunocompromised patient and to initiate systemic antiviral treatment while awaiting the results of laboratory evaluation to confirm the suspected diagnosis.

Event-based soil loss models for construction sites

NASA Astrophysics Data System (ADS)

Trenouth, William R.; Gharabaghi, Bahram

2015-05-01

The elevated rates of soil erosion stemming from land clearing and grading activities during urban development, can result in excessive amounts of eroded sediments entering waterways and causing harm to the biota living therein. However, construction site event-based soil loss simulations - required for reliable design of erosion and sediment controls - are one of the most uncertain types of hydrologic models. This study presents models with improved degree of accuracy to advance the design of erosion and sediment controls for construction sites. The new models are developed using multiple linear regression (MLR) on event-based permutations of the Universal Soil Loss Equation (USLE) and artificial neural networks (ANN). These models were developed using surface runoff monitoring datasets obtained from three sites - Greensborough, Cookstown, and Alcona - in Ontario and datasets mined from the literature for three additional sites - Treynor, Iowa, Coshocton, Ohio and Cordoba, Spain. The predictive MLR and ANN models can serve as both diagnostic and design tools for the effective sizing of erosion and sediment controls on active construction sites, and can be used for dynamic scenario forecasting when considering rapidly changing land use conditions during various phases of construction.

[Sediment transport characteristics at different erosion stages for non-hardened roads of the Shenfu Coalfield, west China].

PubMed

Guo, Ming-ming; Wang, Wen-long; Li, Jian-ming; Huang, Peng-fei; Zhu, Bao-cai; Wang, Zhen; Luo, Ting

2015-02-01

Non-hardened roads formed in the production of the Shenfu Coalfield have a unique condition of underlying surface. The road surface is composed of a regolith layer with a certain thickness resulted from long-term rolling and thus, is characterized by weakened anti-scourabilty and anti-erodibility. In contrast, soil layer below the regolith has a higher bulk density and anti-erodibility. The processes of soil erosion on the non-hardened roads exhibit some differences under rainfall condition. The process of sediment transport and the relationship between sediment transport rate and erosion factors at different erosion stages were studied on non-hardened roads with slope degrees ranging from 3° to 12° (3°, 6°, 9°, 12°) by a field experiment under artificial rainfall. Results showed that the first peak of sediment transport on the regolith surface was observed at the sheet erosion stage. Sheet erosion occurred only at 3° slope degree, with an average variation coefficient of 0.07 for sediment transport rate. Rills in every testing began to develop at slope degrees of 6° to 12° about 15 min after runoff initiation. At the sheet erosion stage, the process of sediment transport fluctuated considerably at rainfall intensities of > 1.5 mm · min(-1), but the differences in its variation were little at the three slope degrees, with average variation coefficients of 0.20, 0.19 and 0.16, respectively. Rainfall intensity had a more significant impact on sediment transport rate than slope degree. The process of sediment transport at the rill erosion stage fluctuated, but the fluctuation was obviously smaller than that at the sheet erosion stage, with average variation coefficients of 0.05, 0.09 and 0.10 at the three slope degrees. Many wide and shallow rills evolved at the rill erosion stage. The sediment transport rate could be well predicted by a power function of rainfall intensity and slope degree at the sheet and rill erosion stages. The stable sediment transport rate for all the tests was linearly related to runoff rate and sediment concentration.

Continued development of abradable gas path seals. [for gas turbine engines

NASA Technical Reports Server (NTRS)

Shiembob, L. T.

1975-01-01

Major program objectives were the continued development of NiCrAlY feltmetal and honeycomb systems for knife edge seal applications in the 1144 to 1366 K temperature range, and to initiate abradable seal material evaluation for blade tip seal applications in the 1366 to 1589 K temperature range. Larger fiber size, higher density feltmetal showed greatly improved erosion resistance with a slight reduction in abradability compared to the baseline feltmetal. Pack aluminide coating of the honeycomb extended the oxidation resistance and slightly improved the abradability of this material. Evaluation through selected abradability, erosion and oxidation testing, and pertinent metallography led to selection of a plasma sprayed yttria stabilized zirconia (ZrO2)/CoCrAlY layered system as the system with the most potential to meet the 1589 K requirement for blade tip seals. This system demonstrated structural integrity, erosion resistance, and some degree of abradability.

GITR Simulation of Helium Exposed Tungsten Erosion and Redistribution in PISCES-A

NASA Astrophysics Data System (ADS)

Younkin, T. R.; Green, D. L.; Doerner, R. P.; Nishijima, D.; Drobny, J.; Canik, J. M.; Wirth, B. D.

2017-10-01

The extreme heat, charged particle, and neutron flux / fluence to plasma facing materials in magnetically confined fusion devices has motivated research to understand, predict, and mitigate the associated detrimental effects. Of relevance to the ITER divertor is the helium interaction with the tungsten divertor, the resulting erosion and migration of impurities. The linear plasma device PISCES A has performed dedicated experiments for high (4x10-22 m-2s-1) and low (4x10-21 m-2s-1) flux, 250 eV He exposed tungsten targets to assess the net and gross erosion of tungsten and volumetric transport. The temperature of the target was held between 400 and 600 degrees C. We present results of the erosion / migration / re-deposition of W during the experiment from the GITR (Global Impurity Transport) code coupled to materials response models. In particular, the modeled and experimental W I emission spectroscopy data for the 429.4 nm wavelength and net erosion through target and collector mass difference measurements are compared. Overall, the predictions are in good agreement with experiments. This material is supported by the US DOE, Office of Science, Office of Fusion Energy Sciences and Office of Advanced Scientific Computing Research through the SciDAC program on Plasma-Surface Interactions.

Dental erosion and its association with diet in Libyan schoolchildren.

PubMed

Huew, R; Waterhouse, P J; Moynihan, P J; Kometa, S; Maguire, A

2011-10-01

To investigate any association between dental erosion and its potential dietary risk factors in a group of schoolchildren in Benghazi, Libya. A cross-sectional observational study. A random sample of 12-year-old schoolchildren in 36 randomly selected schools completed a questionnaire to provide dietary data and underwent dental examination. Dental erosion was assessed using UK National Diet and Nutrition Survey (2000) criteria. Associations between erosion and dietary variables under study were investigated through processes of bivariate and multivariate analyses. Of 791 schoolchildren dentally examined, 40.8% had dental erosion; erosion into enamel affecting 32.5%, into dentine affecting 8% and into pulp affecting 0.3% of subjects. Bivariate analysis showed frequency of fruit-based sugary drink intake was statistically significantly and positively associated with erosion (p=0.006, Odds Ratio; 1.498, 95% CI; 1.124, 1.996) as was the length of time taken to consume acidic drinks (p≠0.005, Odds Ratio; 1.593, 95%CI; 1.161, 2.186). Additionally, multivariate analysis showed frequency of consumption of fruit other than bananas, sugared tea with milk and flavoured milk to also be positively associated with erosion (p=<0.05). In this group of Libyan 12-year-olds, frequency of consumption of fruit-based sugary drinks and length of time taken to consume acidic drinks were the primary statistically significant positive risk factors for dental erosion.

Quantification of long-term erosion rates from root exposure/tree age relationships in an alpine meadow catchment

NASA Astrophysics Data System (ADS)

Scuderi, Louis A.

2017-04-01

Erosion rates derived using dendrogeomorphology have been used to quantify slope degradation in many localities globally. However, with the exception of the western United States, most of these estimates are derived from short-lived trees whose lifetimes may not adequately reflect the complete range of slope processes which can include erosion, deposition, impacts of extreme events and even long-term hiatuses. Erosion rate estimates at a given site using standard techniques therefore reflect censored local point erosion estimates rather than long-term rates. We applied a modified dendrogeomorphic approach to rapidly estimate erosion rates from dbh/age relationships to assess the difference between short and long-term rates and found that the mean short-term rate was 0.13 cm/yr with high variability, while the uncensored long-term rate was 0.06 cm/yr. The results indicate that rates calculated from short-lived trees, while possibly appropriate for local short-term point estimates of erosion, are highly variable and may overestimate regional long-term rates by > 50%. While these findings do not invalidate the use of dendrogeomorphology to estimate erosion rates they do suggest that care must be taken to select older trees that incorporate a range of slope histories in order to best approximate regional long-term rates.

A new experimental material for modeling relief dynamics and interactions between tectonics and surface processes

NASA Astrophysics Data System (ADS)

Graveleau, F.; Hurtrez, J.-E.; Dominguez, S.; Malavieille, J.

2011-12-01

We developed a new granular material (MatIV) to study experimentally landscape evolution in active mountain belt piedmonts. Its composition and related physical properties have been determined using empirical criteria derived from the scaling of deformation, erosion-transport and sedimentation natural processes. MatIV is a water-saturated composite material made up with 4 granular components (silica powder, glass microbeads, plastic powder and graphite) whose physical, mechanical and erosion-related properties were measured with different laboratory tests. Mechanical measurements were made on a modified Hubbert-type direct shear apparatus. Erosion-related properties were determined using an experimental set-up that allows quantifying the erosion/sedimentation budget from tilted relaxation topographies. For MatIV, we also investigated the evolution of mean erosion rates and stream power erosion law exponents in 1D as a function of slope. Our results indicate that MatIV satisfies most of the defined criteria. It deforms brittlely according to the linear Mohr-Coulomb failure criterion and localizes deformation along discrete faults. Its erosion pattern is characterized by realistic hillslope and channelized processes (slope diffusion, mass wasting, channel incision). During transport, eroded particles are sorted depending on their density and shape, which results in stratified alluvial deposits displaying lateral facies variations. To evaluate the degree of similitude between model and nature, we used a new experimental device that combines accretionary wedge deformation mechanisms and surface runoff erosion processes. Results indicate that MatIV succeeded in producing detailed morphological and sedimentological features (drainage basin, channel network, terrace, syntectonic alluvial fan). Geometric, kinematic and dynamic similarity criteria have been investigated to compare precisely model to nature. Although scaling is incomplete, it yields particularly informative orders of magnitude. With all these characteristics, MatIV appears as a very promising material to investigate experimentally a wide range of scientific questions dealing with relief dynamics and interactions between tectonics, erosion and sedimentation processes.

Effect of abdominal visceral fat on the development of new erosive oesophagitis: a prospective cohort study.

PubMed

Nam, Su Youn; Kim, Young-Woo; Park, Bum Joon; Ryu, Kum Hei; Choi, Il Ju; Nam, Byung-Ho; Kim, Hyun Boem

2017-04-01

Although abdominal visceral fat has been associated with erosive oesophagitis in cross-sectional studies, there are no data that describe its longitudinal effects. We aimed to evaluate the longitudinal effects of abdominal visceral fat on the development of new erosive oesophagitis in patients who did not have erosive oesophagitis at baseline. This was a single-centre prospective study. A total of 1503 participants without erosive oesophagitis at baseline were followed up for 34 months and they underwent oesophagogastroduodenoscopy and computed tomography at both baseline and during follow-up. The longitudinal effects of abdominal visceral fat on the development of new erosive oesophagitis were evaluated using odds ratios (ORs) and 95% confidence intervals (CIs). New oesophagitis developed in 83 patients. Compared with the first quartile, the third (OR=3.96, 95% CI: 1.54-10.18) and the fourth (OR=4.67, 95% CI: 1.79-12.23) of baseline visceral fat quartiles, the third (OR=3.03, 95% CI: 1.14-8.04) and the fourth (OR=7.50, 95% CI: 2.92-19.25) follow-up visceral fat quartiles, and the fourth visceral fat change quartile (OR=2.76, 95% CI: 1.47-5.21) were associated with increased development of new erosive oesophagitis, and the P value for each trend was less than 0.001. New erosive oesophagitis was inversely related to the follow-up Helicobacter pylori status and it was associated positively with the presence of a hiatal hernia and smoking during follow-up, but it was not associated with reflux symptoms, the H. pylori status, presence of a hiatal hernia or smoking at baseline. Higher level of visceral fat at baseline and follow-up visceral fat, and greater changes in the visceral level were associated linearly with the development of new erosive oesophagitis in this longitudinal study.

Dental Erosion and its Associated Factors In 11-16-Year Old School Children.

PubMed

Kirthiga, M; Poornima, P; Praveen, R; Sakeena, B; Disha, P

2015-01-01

Dental erosion currently stands as a great challenge for the clinician, regarding the diagnosis, identification of the etiological factors, prevention and execution of an adequate treatment. To evaluate the prevalence, severity, and associated factors on dental erosion in 11-16-years old. A cross sectional study was conducted among 2000 school children who were randomly selected. A questionnaire was given to the children that included personal demographic details and habit of consuming acidic foods and drinks. An index specific for dental erosion given by O Sullivan was used to assess every affected tooth. The values were subjected to chi-square test and multivariate logistic regression analysis. The prevalence of dental erosion was found to be 1.4%. Females (1.6%) were slightly more affected than males (1.3%). Public school children (2.1%) were found to be affected a little more than private children (0.7%). Chi square test showed significant association between type of school and erosion prevalence (p = 0.015). Most commonly affected teeth were lateral incisor (59.72%). The prevalence of dental erosion was found to be low when compared to various studies done all over the world.

Erosion of Earthen Levees by Wave Action

NASA Astrophysics Data System (ADS)

Ozeren, Y.; Wren, D. G.; Reba, M. L.

2016-02-01

Earthen levees of aquaculture and irrigation reservoirs in the United States often experience significant erosion due to wind-generated waves. Typically constructed using local soils, unprotected levees are subjected to rapid erosion and retreat due to wind generated waves and surface runoff. Only a limited amount of published work addresses the erosion rates for unprotected levees, and producers who rely on irrigation reservoirs need an economic basis for selecting a protection method for vulnerable levees. This, in turn, means that a relationship between wave energy and erosion of cohesive soils is needed. In this study, laboratory experiments were carried out in order to quantify wave induced levee erosion and retreat. A model erodible bank was packed using a soil consisting of approximately 14% sand, 73% silt, and 13% clay in a 20.6 m long 0.7 m wide and 1.2 m deep wave tank at the USDA-ARS, National Sedimentation Laboratory in Oxford MS. The geometry of the levee face was monitored by digital camera and the waves were measured by means of 6 capacitance wave staffs. Relationships were established between levee erosion, edge and retreat rates, and incident wave energy.

Atomic Oxygen Erosion Yield Predictive Tool for Spacecraft Polymers in Low Earth Orbit

NASA Technical Reports Server (NTRS)

Bank, Bruce A.; de Groh, Kim K.; Backus, Jane A.

2008-01-01

A predictive tool was developed to estimate the low Earth orbit (LEO) atomic oxygen erosion yield of polymers based on the results of the Polymer Erosion and Contamination Experiment (PEACE) Polymers experiment flown as part of the Materials International Space Station Experiment 2 (MISSE 2). The MISSE 2 PEACE experiment accurately measured the erosion yield of a wide variety of polymers and pyrolytic graphite. The 40 different materials tested were selected specifically to represent a variety of polymers used in space as well as a wide variety of polymer chemical structures. The resulting erosion yield data was used to develop a predictive tool which utilizes chemical structure and physical properties of polymers that can be measured in ground laboratory testing to predict the in-space atomic oxygen erosion yield of a polymer. The properties include chemical structure, bonding information, density and ash content. The resulting predictive tool has a correlation coefficient of 0.914 when compared with actual MISSE 2 space data for 38 polymers and pyrolytic graphite. The intent of the predictive tool is to be able to make estimates of atomic oxygen erosion yields for new polymers without requiring expensive and time consumptive in-space testing.

Testing the Success Rate of Establishing Multitrophic Vegetation for Stream Buffer Mitigation According to Georgia DOT Specifications on Different Slope Ratios

DOT National Transportation Integrated Search

2017-02-01

Multitrophic vegetative mitigation is required for stream buffers, wetlands, and retention basins within state waters. Downslopes adjacent to linear road construction are typically steep, which creates challenges for establishment and erosion control...

Water erosion susceptibility mapping by applying Stochastic Gradient Treeboost to the Imera Meridionale River Basin (Sicily, Italy)

NASA Astrophysics Data System (ADS)

Angileri, Silvia Eleonora; Conoscenti, Christian; Hochschild, Volker; Märker, Michael; Rotigliano, Edoardo; Agnesi, Valerio

2016-06-01

Soil erosion by water constitutes a serious problem affecting various countries. In the last few years, a number of studies have adopted statistical approaches for erosion susceptibility zonation. In this study, the Stochastic Gradient Treeboost (SGT) was tested as a multivariate statistical tool for exploring, analyzing and predicting the spatial occurrence of rill-interrill erosion and gully erosion. This technique implements the stochastic gradient boosting algorithm with a tree-based method. The study area is a 9.5 km2 river catchment located in central-northern Sicily (Italy), where water erosion processes are prevalent, and affect the agricultural productivity of local communities. In order to model soil erosion by water, the spatial distribution of landforms due to rill-interrill and gully erosion was mapped and 12 environmental variables were selected as predictors. Four calibration and four validation subsets were obtained by randomly extracting sets of negative cases, both for rill-interrill erosion and gully erosion models. The results of validation, based on receiving operating characteristic (ROC) curves, showed excellent to outstanding accuracies of the models, and thus a high prediction skill. Moreover, SGT allowed us to explore the relationships between erosion landforms and predictors. A different suite of predictor variables was found to be important for the two models. Elevation, aspect, landform classification and land-use are the main controlling factors for rill-interrill erosion, whilst the stream power index, plan curvature and the topographic wetness index were the most important independent variables for gullies. Finally, an ROC plot analysis made it possible to define a threshold value to classify cells according to the presence/absence of the two erosion processes. Hence, by heuristically combining the resulting rill-interrill erosion and gully erosion susceptibility maps, an integrated water erosion susceptibility map was created. The adopted method offers the advantages of an objective and repeatable procedure, whose result is useful for local administrators to identify the areas that are most susceptible to water erosion and best allocate resources for soil conservation strategies.

Assessment of Tooth Wear Among Glass Factory Workers: WHO 2013 Oral Health Survey

PubMed Central

Bhat, Nagesh; Asawa, Kailash; Tak, Mridula; Bapat, Salil; Gupta, Vivek Vardhan

2015-01-01

Background Glass factory workers are often exposed to the hazardous environment that leads to deleterious oral health and subsequently, general health. We planned to determine the effects of the particulates present in the milieu on the tooth wear among workers. Aim To assess tooth wear among glass factory workers in Jaipur, Rajasthan, India. Settings and Design A descriptive cross-sectional survey was conducted among 936 glass workers in Jaipur, Rajasthan, India from January-June 2014. Materials and Methods A survey proforma was designed for tooth wear evaluation with the help of WHO Oral Health Assessment form 2013 (for adults). Information regarding oral health practices, adverse habits and dietary habits, demographic details was gathered and clinical parameters were recorded. Statistical Analysis The Chi–square test, t–test, One-way Analysis of Variance and a Stepwise multiple linear regression analysis. Results The most prevalent form of erosion was enamel erosion (589, 62.93%) with few subjects of deeper dentinal erosion and the difference was statistically significant (p=0.001). Dental erosion was found to be higher among males compared to females. Years of experience and educational status were identified as best predictors for dental erosion. Conclusion It was concluded that there was considerable evidence of dental erosion found among the factory workers. Due to ignorance on social, cultural and health aspects, professional approach with regular dental care services for detection of early symptoms and planning of preventive strategies is warranted. PMID:26436050

Arroyo channel head evolution in a flash-flood-dominated discontinuous ephemeral stream system

USGS Publications Warehouse

DeLong, Stephen B.; Johnson, Joel P.L.; Whipple, Kelin X.

2014-01-01

We study whether arroyo channel head retreat in dryland discontinuous ephemeral streams is driven by surface runoff, seepage erosion, mass wasting, or some combination of these hydrogeomorphic processes. We monitored precipitation, overland flow, soil moisture, and headcut migration over several seasonal cycles at two adjacent rangeland channel heads in southern Arizona. Erosion occurred by headward retreat of vertical to overhanging faces, driven dominantly by surface runoff. No evidence exists for erosion caused by shallow-groundwater–related processes, even though similar theater-headed morphologies are sometimes attributed to seepage erosion by emerging groundwater. At our field site, vertical variation in soil shear strength influenced the persistence of the characteristic theater-head form. The dominant processes of erosion included removal of grains and soil aggregates during even very shallow (1–3 cm) overland flow events by runoff on vertical to overhanging channel headwalls, plunge-pool erosion during higher-discharge runoff events, immediate postrunoff wet mass wasting, and minor intra-event dry mass wasting on soil tension fractures developing subparallel to the headwall. Multiple stepwise linear regression indicates that the migration rate is most strongly correlated with flow duration and total precipitation and is poorly correlated with peak flow depth or time-integrated flow depth. The studied channel heads migrated upslope with a self-similar morphologic form under a wide range of hydrological conditions, and the most powerful flash floods were not always responsible for the largest changes in landscape form in this environment. 

Estimating eroded soil and predicting further erosion in Daisetsuzan National Park in Hokkaido, Japan

NASA Astrophysics Data System (ADS)

Kobayashi, Yusuke; Watanabe, Teiji

2017-04-01

This study has three objectives: (1) to estimate changes of the eroded volume of mountain trails from 2014 to 2016 by making DSMs, (2) to understand a relationship between the trail erosion and micro-topography, and (3) to predict the volume of soil that can be eroded in future. Trail erosion has been investigated near Mt. Hokkai-dake in Daisetzuzan National Park, Hokkaido, northern Japan, with a drone (UAV) from 2014 to 2016. Seven segments with the soil erosion from starting sites to ending sites were selected to make DSMs and Orthophotographs by Agisoft, which is one of the Structure from Motion (SfM) software. Then, at fourteen points in each of the seven segments were selected to estimate the volume of soil that can be eroded in the future by PANDA2, a soil compaction penetrometer. The eroded volume in the segment with the largest eroded value attained 274.67 m3 for the two-year period although extremely heavy rain hit this area in the 2016 summer. The result obtained by PANDA2 shows that soil more than 100 cm in depth will be potentially eroded at four points in three years to one hundred years.

Developing a geomorphic approach for ranking watersheds for rehabilitation, Zuni Indian Reservation, New Mexico

USGS Publications Warehouse

Gellis, A.C.; Cheama, A.; Lalio, S.M.

2001-01-01

As a result of past erosion problems on the Zuni Indian Reservation in western New Mexico, the US Congress in 1990 authorized the Zuni Tribe to begin a program for watershed rehabilitation. This paper describes an approach to rank the most appropriate watersheds for rehabilitation for the Zuni Reservation. The approach was based on data collected during a 3-year study on geomorphic and anthropogenic characteristics of the Rio Nutria Watershed, including data on (i) arroyo cross-sectional changes, (ii) erosion-control structures, and (iii) sheetwash erosion. Results of this 3-year study indicated that 61 of 85 channel cross-sections aggraded and channels with lower width-to-depth ratios eroded. Results on assessment of erosion-control structures, some dating back to the 1930's, indicated that 60% of earthen dams and 22% of rock-and-brush structures were breached or flanked in the Rio Nutria Watershed. Sheetwash erosion measured on five land-cover sites (sagebrush, pasture, chained pin??on and juniper, unchained pin??on and juniper, and ponderosa pine) indicated chained pin??on and juniper sites and pasture sites had the highest volume-weighted sediment concentrations of 13,000 and 9970 ppm, respectively. Based on interpretations of the 3-year study in the Rio Nutria Watershed, a two-stage approach was developed to rank the most appropriate watersheds for rehabilitation on the Zuni Reservation. In the first stage, the reservation was divided into eight major watersheds, which were ranked according to the most potential for erosion. In the second stage, the watershed with the most potential for erosion was divided into sub-basins, which were ranked according to the most potential for erosion. Quantitative and qualitative information on physical and anthropogenic factors were used at each stage to rank the watersheds. Quantitative physical data included headcut density, percentage of bare ground, percentage of chained area, channel width-to-depth ratio, change in channel density from 1934 to 1988, and sheetwash erosion rates. Qualitative physical data included erosion rankings on the main channels, tributaries, and entire basins. Anthropogenic data included density of dirt roads and condition of erosion-control structures. A community survey and agricultural acreage were also used in the selection process. The first stage analysis resulted in the selection of the Rio Nutria Watershed as the most appropriate major watershed for rehabilitation. In the second stage, the Rio Nutria Watershed was divided into 15 sub-basins; the analysis indicated the highest priority sub-basins for rehabilitation were Benny Draw, Coal Mine Canyon Draw, and Garcia Draw.

Long-term erosion rates of Panamanian drainage basins determined using in situ 10Be

NASA Astrophysics Data System (ADS)

Gonzalez, Veronica Sosa; Bierman, Paul R.; Nichols, Kyle K.; Rood, Dylan H.

2016-12-01

Erosion rates of tropical landscapes are poorly known. Using measurements of in situ-produced 10Be in quartz extracted from river and landslide sediment samples, we calculate long-term erosion rates for many physiographic regions of Panama. We collected river sediment samples from a wide variety of watersheds (n = 35), and then quantified 24 landscape-scale variables (physiographic, climatic, seismic, geologic, and land-use proxies) for each watershed before determining the relationship between these variables and long-term erosion rates using linear regression, multiple regression, and analysis of variance (ANOVA). We also used grain-size-specific 10Be analysis to infer the effect of landslides on the concentration of 10Be in fluvial sediment and thus on erosion rates. Cosmogenic 10Be-inferred, background erosion rates in Panama range from 26 to 595 m My- 1, with an arithmetic average of 201 m My- 1, and an area-weighted average of 144 m My- 1. The strongest and most significant relationship in the dataset was between erosion rate and silicate weathering rate, the mass of material leaving the basin in solution. None of the topographic variables showed a significant relationship with erosion rate at the 95% significance level; we observed weak but significant correlation between erosion rates and several climatic variables related to precipitation and temperature. On average, erosion rates in Panama are higher than other cosmogenically-derived erosion rates in tropical climates including those from Puerto Rico, Madagascar, Australia and Sri Lanka, likely the result of Panama's active tectonic setting and thus high rates of seismicity and uplift. Contemporary sediment yield and cosmogenically-derived erosion rates for three of the rivers we studied are similar, suggesting that human activities are not increasing sediment yield above long-term erosion rate averages in Panama. 10Be concentration is inversely proportional to grain size in landslide and fluvial samples from Panama; finer grain sizes from landslide material have lower 10Be concentration than fine-grained fluvial sediment. Large grains from both landslide and stream sediments have similarly low 10Be concentrations. These data suggest that fluvial gravel is delivered to the channel by landslides whereas sand is preferentially delivered by soil creep and bank collapse. Furthermore, the difference in 10Be concentration in sand-sized material delivered by soil creep and that delivered by landsliding suggests that the frequency and intensity of landslides influence basin scale erosion rates.

Investigating the effect of lignosulfonate on erosion rate of the embankments constructed with clayey sand.

PubMed

Koohpeyma, Hamid Reza; Vakili, Amir Hossein; Moayedi, Hossein; Panjsetooni, Alireza; Nazir, Ramli

2013-01-01

Internal erosion is known as the most important cause of dam failure after overtopping. It is important to improve the erosion resistance of the erodible soil by selecting an effective technique along with the reasonable costs. To prevent internal erosion of embankment dams the use of chemical stabilizers that reduce the soil erodibility potential is highly recommended. In the present study, a lignin-based chemical, known as lignosulfonate, is used to improve the erodibility of clayey sand specimen. The clayey sand was tested in various hydraulic heads in terms of internal erosion in its natural state as well as when it is mixed with the different percentages of lignosulfonate. The results show that erodibility of collected clayey sand is very high and is dramatically reduced by adding lignosulfonate. Adding 3% of lignosulfonate to clayey sand can reduce the coefficient of soil erosion from 0.01020 to 0.000017. It is also found that the qualitative erodibility of stabilized soil with 3% lignosulfonate is altered from the group of extremely rapid to the group of moderately slow.

Investigating the Effect of Lignosulfonate on Erosion Rate of the Embankments Constructed with Clayey Sand

PubMed Central

Koohpeyma, Hamid Reza; Vakili, Amir Hossein; Panjsetooni, Alireza; Nazir, Ramli

2013-01-01

Internal erosion is known as the most important cause of dam failure after overtopping. It is important to improve the erosion resistance of the erodible soil by selecting an effective technique along with the reasonable costs. To prevent internal erosion of embankment dams the use of chemical stabilizers that reduce the soil erodibility potential is highly recommended. In the present study, a lignin-based chemical, known as lignosulfonate, is used to improve the erodibility of clayey sand specimen. The clayey sand was tested in various hydraulic heads in terms of internal erosion in its natural state as well as when it is mixed with the different percentages of lignosulfonate. The results show that erodibility of collected clayey sand is very high and is dramatically reduced by adding lignosulfonate. Adding 3% of lignosulfonate to clayey sand can reduce the coefficient of soil erosion from 0.01020 to 0.000017. It is also found that the qualitative erodibility of stabilized soil with 3% lignosulfonate is altered from the group of extremely rapid to the group of moderately slow. PMID:24459437

In-Situ Measurement of Hall Thruster Erosion Using a Fiber Optic Regression Probe

NASA Technical Reports Server (NTRS)

Polzin, Kurt; Korman, Valentin

2009-01-01

One potential life-limiting mechanism in a Hall thruster is the erosion of the ceramic material comprising the discharge channel. This is especially true for missions that require long thrusting periods and can be problematic for lifetime qualification, especially when attempting to qualify a thruster by analysis rather than a test lasting the full duration of the mission. In addition to lifetime, several analytical and numerical models include electrode erosion as a mechanism contributing to enhanced transport properties. However, there is still a great deal of dispute over the importance of erosion to transport in Hall thrusters. The capability to perform an in-situ measurement of discharge channel erosion is useful in addressing both the lifetime and transport concerns. An in-situ measurement would allow for real-time data regarding the erosion rates at different operating points, providing a quick method for empirically anchoring any analysis geared towards lifetime qualification. Erosion rate data over a thruster s operating envelope would also be useful in the modeling of the detailed physics inside the discharge chamber. There are many different sensors and techniques that have been employed to quantify discharge channel erosion in Hall thrusters. Snapshots of the wear pattern can be obtained at regular shutdown intervals using laser profilometry. Many non-intrusive techniques of varying complexity and sensitivity have been employed to detect the time-varying presence of erosion products in the thruster plume. These include the use quartz crystal microbalances, emission spectroscopy, laser induced flourescence, and cavity ring-down spectroscopy. While these techniques can provide a very accurate picture of the level of eroded material in the thruster plume, it is more difficult to use them to determine the location from which the material was eroded. Furthermore, none of the methods cited provide a true in-situ measure of erosion at the channel surface while the thruster is in operation (i.e. none yield a continuous channel erosion measurement). A recent fundamental sensor development effort has led to a novel regression, erosion, and ablation sensor technology (REAST). The REAST sensor allows for measurement of real-time surface erosion rates at a discrete surface location. The sensor was tested using a linear Hall thruster geometry (see Fig. 1), which served as a means of producing plasma erosion of a ceramic discharge chamber. The mass flow rate, discharge voltage, and applied magnetic field strength could be varied, allowing for erosion measurements over a broad thruster operating envelope. Results are presented demonstrating the ability of the REAST sensor to capture not only the insulator erosion rates but also changes in these rates as a function of the discharge parameters.

Soil erosion in mountainous areas: how far can we go?

NASA Astrophysics Data System (ADS)

Egli, Markus

2017-04-01

Erosion is the counter part of soil formation, is a natural process and cannot be completely impeded. With respect to soil protection, the term of tolerable soil erosion, having several definitions, has been created. Tolerable erosion is often equalled to soil formation or production. It is therefore crucial that we know the rates of soil formation when discussing sustainability of soil use and management. Natural rates of soil formation or production are determined by mineral weathering or transformation of parent material into soil, dust deposition and organic matter incorporation. In mountain areas where soil depth is a main limiting factor for soil productivity, the use and management of soils must consider how to preserve them from excessive depth loss and consequent degradation of their physical, chemical and biological properties. Even under natural conditions, landscape surfaces and soils are known to evolve in complex, non-linear ways over time. As a result, soil production and erosion change substantially with time. The fact that soil erosion and soil production processes are discontinuous over time is an aspect that is in most cases completely neglected. To conserve a given situation, tolerable values should take these dynamics into account. Measurements of long and short-term physical erosion rates, total denudation, weathering rates and soil production have recently become much more widely available through cosmogenic and fallout nuclide techniques. In addition to this, soil chronosequences deliver a precious insight into the temporal aspect of soil formation and production. Examples from mountainous and alpine areas demonstrate that soil production rates strongly vary as a function of time (with young soils and eroded surfaces having distinctly higher rates than old soils). Extensive erosion promotes rejuvenation of the surface and, therefore, accelerates chemical weathering and soil production - the resulting soil thickness will however be shallow. The comparison of soil production and erosion rates indicates that the present-day management of grassland soils in several alpine and mountain regions will lead in the long-term to very shallow soils (showing the characteristics of young soils). Shallow soils go along with high 'tolerable' erosion rates. It is, however, strongly doubtful whether this matches the deeper sense of sustainability.

Toothpastes and enamel erosion/abrasion - Impact of active ingredients and the particulate fraction.

PubMed

Ganss, C; Marten, J; Hara, A T; Schlueter, N

2016-11-01

To investigate in vitro a range of differently characterised toothpastes with respect to their efficacy in an erosion/abrasion setting with special emphasis on the role of the particulate ingredients. Human enamel samples were erosively demineralised with citric acid (2min, 6×/day; 0.5%, pH 2.5; 10 days) and immersed in slurries (2min, 2×/day) either without or with brushing (15s, load 200g). The toothpastes were eight NaF-toothpastes, three hydroxyapatite-toothpastes (one without and two with NaF), one fluoride-free chitosan-toothpaste and three Sn-toothpastes. Negative control was erosion only, positive control was SnF 2 gel. Tissue loss was quantified profilometrically. The SnF 2 gel was most effective (reduction of tissue loss of 79%). Most of the products reduced tissue loss significantly when applied as slurries (between 28 and 66%). Brushing increased tissue loss in almost all toothpastes, only 5 formulations (all Sn-toothpastes and 2 NaF-toothpastes) reduced tissue loss significantly when compared to negative control (between 33 and 59%). There was a non-linear association between abrasiveness and amount of particles in a formulation, the particle size had no impact. Toothpastes had a protecting effect when applied as slurries but to a much lesser degree when applied with brushing. The particulate fraction may be a determinant for toothpaste efficacy in erosion/abrasion settings. Toothpastes are important carriers of active agents against erosion, but physical impacts through brushing modifies efficacy distinctly. Understanding the role of the particulate fraction in toothpastes may offer perspectives for designing effective formulations for patients with erosive lesions. Copyright © 2016 Elsevier Ltd. All rights reserved.

The influence of changes in land use and landscape patterns on soil erosion in a watershed.

PubMed

Zhang, Shanghong; Fan, Weiwei; Li, Yueqiang; Yi, Yujun

2017-01-01

It is very important to have a good understanding of the relation between soil erosion and landscape patterns so that soil and water conservation in river basins can be optimized. In this study, this relationship was explored, using the Liusha River Watershed, China, as a case study. A distributed water and sediment model based on the Soil and Water Assessment Tool (SWAT) was developed to simulate soil erosion from different land use types in each sub-basin of the Liusha River Watershed. Observed runoff and sediment data from 1985 to 2005 and land use maps from 1986, 1995, and 2000 were used to calibrate and validate the model. The erosion modulus for each sub-basin was calculated from SWAT model results using the different land use maps and 12 landscape indices were chosen and calculated to describe the land use in each sub-basin for the different years. The variations in instead of the absolute amounts of the erosion modulus and the landscape indices for each sub-basin were used as the dependent and independent variables, respectively, for the regression equations derived from multiple linear regression. The results indicated that the variations in the erosion modulus were closely related to changes in the large patch index, patch cohesion index, modified Simpson's evenness index, and the aggregation index. From the regression equation and the corresponding landscape indices, it was found that watershed erosion can be reduced by decreasing the physical connectivity between patches, improving the evenness of the landscape patch types, enriching landscape types, and enhancing the degree of aggregation between the landscape patches. These findings will be useful for water and soil conservation and for optimizing the management of watershed landscapes. Copyright © 2016 Elsevier B.V. All rights reserved.

Soil erosion risk mapping: how to explain the stakeholders what lies behind?

NASA Astrophysics Data System (ADS)

Cerdan, Olivier; Degan, Francesca; Salvador-Blanes, Sebastien

2014-05-01

Recent demographic projections of the impact of global changes point to the need of increasing food and biomass production to meet expected global demand. This issue is particularly complex as it must comply with an increasing awareness that environmental quality must be preserved. Increased production can be achieved through either an intensification of agricultural practices or an increase of cultivated areas. In both cases, significant adverse effects are expected in terms of land degradation and its ability to maintain sustainable agricultural productivity. In this context, soil degradation vulnerability assessment is becoming more and more integrated in land management planning. Soil erosion being one of the major causes of soil degradation, the demand for soil erosion risk maps is increasing. However, the 2D representation of a process that shows strong non-linear dynamics in space and time is far from trivial. Important assumptions on the way to integrate these heterogeneities in time and space have to be made. How to integrate the crop rotation calendar and the climatic seasonal variability at the yearly scale? Or, how to characterise the erosion vulnerability of a geographical space that combines areas having different erosion risks? Moreover, other important questions arise with the resolution and the uncertainties associated with the available input data. And, last but not least, the final map needs, not only to integrate all these issues, but, more importantly, to be understandable by public managers. In this paper we illustrate the different difficulties inherent to soil erosion mapping, taking an example in different catchments of the Loire valley in France and present possible options to the spatial integration of both temporal and spatial variations in erosion risk.

The effect of increasing sodium fluoride concentrations on erosion and attrition of enamel and dentine in vitro.

PubMed

Austin, R S; Rodriguez, J M; Dunne, S; Moazzez, R; Bartlett, D W

2010-10-01

To investigate the effect of an aqueous sodium fluoride solution of increasing concentration on erosion and attrition of enamel and dentine in vitro. Enamel and dentine sections from caries-free human third molars were polished flat and taped (exposing a 3 mm x 3 mm area) before being randomly allocated to 1 of 5 groups per substrate (n=10/gp): G1 (distilled water control); G2 (225 ppm NaF); G3 (1450 ppm NaF); G4 (5000 ppm NaF); G5 (19,000 ppm NaF). All specimens were subjected to 5, 10 and 15 cycles of experimental wear [1 cycle=artificial saliva (2h, pH 7.0)+erosion (0.3% citric acid, pH 3.2, 5 min)+fluoride/control (5 min)+attrition (60 linear strokes in artificial saliva from enamel antagonists loaded to 300 g)]. Following tape removal, step height (SH) in mum was measured using optical profilometry. When the number of cycles increased the amount of tooth surface loss increased significantly in enamel and dentine after attrition and erosion and for dentine after attrition. Attrition and erosion resulted in greater surface loss than attrition alone after 15 cycles of experimental wear of enamel. 5000 ppm and 19,000 ppm sodium fluoride solutions had a protective effect on erosive and attritional enamel tooth wear in vitro, however no other groups showed significant differences. The more intensive the fluoride regime the more protection was afforded to enamel from attrition and erosion. However, in this study no such protective effect was demonstrated for dentine. Copyright 2010 Elsevier Ltd. All rights reserved.

Comparison Between Bandage Contact Lenses and Pressure Patching on the Erosion Area and Pain Scale in Patients With Corneal Erosion.

PubMed

Triharpini, Ni Nyoman; Gede Jayanegara, I Wayan; Handayani, Ariesanti Tri; Widiana, I Gde Raka

2015-01-01

Corneal erosion is common in eye emergency cases. Extensive corneal erosions result in severe pain and prolonged healing time. This study aimed to compare bandage contact lenses with pressure patching in terms of reducing the size of the erosion area, pain scale in patients with corneal erosion and its complications. A randomized open-label clinical trial was conducted. Subjects with mechanical corneal erosion were selected to use either bandage contact lenses or pressure patching. All subjects received antibiotic eye drops and 0.5% tropicamide eye drops. Evaluations were done 24 and 72 hours after treatment. The size of the corneal erosion area, pain scale, and complications were assessed. A total of 32 eyes (16 eyes in each group) were studied. The change in the size of the corneal erosion area was greater in the bandage contact lens group than in the pressure patching group, although there was no significant difference. In the bandage contact lens group, 56.25% of the eyes were healed at 24 hours and 43.75% were healed at 72 hours. In the pressure patching group, 62.50% were healed at 24 hours and 12.50% were healed at 72 hours. The change in pain scale was significantly greater in the bandage contact lens group than in the pressure patching group. No complications were found in both groups. Bandage contact lenses are an effective alternative to treating mechanical corneal erosion because of their effect in reducing pain without causing any complications.

Reduction of Gun Erosion and Correlation of Gun Erosion Measurements

NASA Technical Reports Server (NTRS)

Bogdanoff, Dave; Wercinski, Paul (Technical Monitor)

1997-01-01

Gun barrel erosion is serious problem with two-stage light gas guns. Excessive barrel erosion can lead to poor or failed launches and frequent barrel changes, with the corresponding down time. Also, excessive barrel erosion can limit the maximum velocity obtainable by loading down the hydrogen working gas with eroded barrel material. Guided by a CFD code, the operating conditions of the Ames 0.5-inch gun were modified to reduce barrel erosion. The changes implemented included: (1) reduction in the piston mass, powder mass and hydrogen fill pressure; and (2) reduction in pump tube volume, while maintaining hydrogen mass. The latter change was found, in particular, to greatly reduce barrel erosion. For muzzle velocity ranges of 6.1 - 6.9 km/sec, the barrel erosion was reduced by a factor of 10. Even for the higher muzzle velocity range of 7.0 - 8.2 km/sec, the barrel erosion was reduced by a factor of 4. Gun erosion data from the Ames 0.5-inch, 1.0-inch, and 1.5-inch guns operated over a wide variety of launch conditions was examined and it was found that this data could be correlated using four different parameters: normalized powder charge energy, normalized hydrogen energy density, normalized pump tube volume and barrel diameter. The development of the correlation and the steps used to collapse the experimental data are presented. Over a certain parameter range in the correlation developed, the barrel erosion per shot is found to increase very rapidly. The correlation should prove useful in the selection of gun operating conditions and the design of new guns. Representative shapes of eroded gun barrels are also presented.

Influence of Intrinsic Factors on Erosive Tooth Wear in a Large-Scale Epidemiological Study.

PubMed

Alaraudanjoki, Viivi; Laitala, Marja-Liisa; Tjäderhane, Leo; Pesonen, Paula; Lussi, Adrian; Ronkainen, Jukka; Anttonen, Vuokko

2016-01-01

To assess the influence of self-reported intrinsic factors [gastroesophageal reflux disease (GERD), long-term alcoholism, long-term heavy use of alcohol and multiple pregnancies] on erosive tooth wear in a middle-aged cohort sample. Of the total Northern Finland Birth Cohort (NFBC 1966), a convenience sample (n = 3,181) was invited for an oral health examination in 2012-2013, of which 1,962 participated, comprising the final study group. Erosive tooth wear was assessed by sextants using the Basic Erosive Wear Examination Index (BEWE, 0-18). Clinical data were supplemented by questionnaires conducted in 1997/1998 and 2012/2013. The participants were divided into severe (BEWE sum ≥9) and no-to-moderate (BEWE sum 0-8) erosive wear groups, and the logistic regression model was applied. Selected intrinsic factors were quite rare in this cohort sample and explained only 5.9% of the difference in the prevalence and severity of erosive wear. Daily symptoms of GERD [odds ratio (OR) 3.8, confidence interval (CI) 1.2-12.0] and hyposalivation (OR 3.8, CI 1.2-11.8) were the strongest risk indicators for severe erosive wear. Additionally, variables associated with an elevated risk for severe erosive wear were diagnosed alcoholism at any point (OR 2.5, CI 0.7-9.7) and self-reported heavy use of alcohol in both questionnaires (OR 2.0, CI 0.6-6.2). Even low-dose long-term consumption of alcohol was associated with erosive wear. In this cohort sample, intrinsic factors such as GERD or alcoholism alone are relatively uncommon causes of erosive tooth wear. The role of long-term use of alcohol in the erosion process may be bigger than presumed. © 2016 S. Karger AG, Basel.

Dental Erosion and Dentin Hypersensitivity among Adult Asthmatics and Non-asthmatics Hospital-based: A Preliminary Study.

PubMed

Farag, Zahra Hassan Abdelaziz; Awooda, Elhadi Mohieldin

2016-01-01

Asthma is a chronic inflammatory condition affecting the airways leading to spasm and swelling of the airways. The medications taken for the treatment of asthma can result in dental erosion and dentin hypersensitivity. The aims of this study were to investigate the severity of dental erosion amongst adult asthmatics according to: gender, type and duration of medication taken and to compare dental erosion and dentin hypersensitivity between asthmatics and non-asthmatics. Comparative, cross-sectional hospital based study among 40 asthmatics (M=15 & F=25) and 40 non-asthmatics (M=18 & F=22) in the age range of 18-60 year selected purposefully from Al-Shaab Teaching Hospital in Khartoum city. The Basic Erosive Wear Index was used for dental erosion assessment. Dentine hypersensitivity was determined by giving ice cold water and rated using the Visual Analogue Scale. Chi-square and Student's t-test were used for statistical analysis with P value ≤.05. There was an association between severity of dental erosion and presence of asthma (P=0.03), where asthmatics had a higher degree of erosion (moderate and severe) and non-asthmatics a lower degree. No significant association was found between dental erosion and gender, type and duration of medication among asthmatics group. A statistically significant difference was revealed in the degree of dentin hypersensitivity (P=0.00) among asthmatics (35.13%) and non-asthmatics (14.13%). Asthmatic patients had a higher degree of dental erosion and dentin hypersensitivity compared to non-asthmatics. Among asthmatic patients there was no association between severity of dental erosion and gender, type and duration medication was taken for.

First application of the WEPP model to predict runoff and erosion risk in fire-affected volcanic areas in Europe

NASA Astrophysics Data System (ADS)

Neris, Jonay; Robichaud, Peter R.; Elliot, William J.; Doerr, Stefan H.; Notario del Pino, Jesús S.; Lado, Marcos

2017-04-01

An estimated that 15% of the world's population lives in volcanic areas. Recent catastrophic erosion events following wildfires in volcanic terrain have highlighted the geomorphological instability of this soil type under disturbed conditions and steep slopes. Predicting the hydrological and erosional response of this soils in the post-fire period is the first step to design and develop adequate actions to minimize risks in the post-fire period. In this work we apply, for the first time, the Water Erosion Prediction Project model for predicting erosion and runoff events in fire-affected volcanic soils in Europe. Two areas affected by wildfires in 2015 were selected in Tenerife (Spain) representative of different fire behaviour (downhill surface fire with long residence time vs uphill crown fire with short residence time), severity (moderate soil burn severity vs light soil burn severity) and climatic conditions (average annual precipitation of 750 and 210 mm respectively). The actual erosion processes were monitored in the field using silt fences. Rainfall and rill simulations were conducted to determine hydrologic, interrill and rill erosion parameters. The soils were sampled and key properties used as model input, evaluated. During the first 18 months after the fire 7 storms produced runoff and erosion in the selected areas. Sediment delivery reached 5.4 and 2.5 Mg ha-1 respectively in the first rainfall event monitored after the fire, figures comparable to those reported for fire-affected areas of the western USA with similar climatic conditions but lower than those showed by wetter environments. The validation of the WEPP model using field data showed reasonable estimates of hillslope sediment delivery in the post-fire period and, therefore, it is suggested that this model can support land managers in volcanic areas in Europe in predicting post-fire hydrological and erosional risks and designing suitable mitigation treatments.

Acquired pellicle as a modulator for dental erosion.

PubMed

Vukosavljevic, Dusa; Custodio, William; Buzalaf, Marilia A R; Hara, Anderson T; Siqueira, Walter L

2014-06-01

Dental erosion is a multifactorial condition that can result in the loss of tooth structure and function, potentially increasing tooth sensitivity. The exposure of enamel to acids from non-bacterial sources is responsible for the progression of erosion. These erosive challenges are counteracted by the anti-erosive properties of the acquired pellicle (AP), an integument formed in vivo as a result of selective adsorption of salivary proteins on the tooth surface, containing also lipids and glycoproteins. This review provides an in-depth discussion regarding how the physical structure of the AP, along with its composition, contributes to AP anti-erosive properties. The physical properties that contribute to AP protective nature include pellicle thickness, maturation time, and site of development. The pellicle contains salivary proteins embedded within its structure that demonstrate anti-erosive properties; however, rather than individual proteins, protein-protein interactions play a fundamental role in the protective nature of the AP. In addition, dietary and synthetic proteins can modify the pellicle, enhancing its protective efficiency against dental erosion. The salivary composition of the AP and its corresponding protein-profile may be employed as a diagnostic tool, since it likely contains salivary biomarkers for oral diseases that initiate at the enamel surface, including dental erosion. Finally, by modifying the composition and structure of the AP, this protein integument has the potential to be used as a target-specific treatment option for oral diseases related to tooth demineralization. Copyright © 2014 The Authors. Published by Elsevier Ltd.. All rights reserved.

Analysis of particle size to erosion wear of sliding sleeve ball seat based on fluent software

NASA Astrophysics Data System (ADS)

Ding, Kun; Yin, Hongcheng; Wan, Bingqian; Cheng, Hao; Xiang, Lu; Li, Jianmin

2017-04-01

The fracturing has become the most offensive stimulation treatment in the low permeability reservoir. But, as the construction displacement and sand dosage of overlong horizontal well were increased continuously, the erosion wear of ball seat of pitching sliding sleeve was increasingly serious, which might lead to the failure of opening the sliding sleeve. In the existing literature, there were many researches on the erosion wear of liquid-solid two-phase flow in the diameter of sudden expansion pipe, but the influence of solid particle with mixed particle size to the erosion wear was not considered. This paper studied the erosion wear of ball seat according to the mixed proppant with different particle sizes, and carried out the numerical simulation with Fluent software with the Euler two-fluid theory. The results showed that: the erosion wear rate of ball seat is in inversely proportional to the particle size of proppant; the erosion wear rate of ball seat is different when the volume fraction of proppant with different particle sizes is changed; and for the mixed proppant of which the particle size is 0.3mm and 0.8mm, the erosion wear rate of ball seat is minimum when the volume fraction of proppant, of which the particle size is 0.3mm, is about 20%. The simulated result contributed to the deep study on erosion wear law of solid particle, and meanwhile, provided a certain reference basis for the selection of staged fracturing material of horizontal well.

Evaluation of the serum zinc level in erosive and non-erosive oral lichen planus.

PubMed

Gholizadeh, N; Mehdipour, M; Najafi, Sh; Bahramian, A; Garjani, Sh; Khoeini Poorfar, H

2014-06-01

Lichen planus is a chronic inflammatory immunologic-based disease involving skin and mucosa. This disease is generally divided into two categories: erosive and non-erosive. Many etiologic factors are deliberated regarding the disease; however, the disorders of immune system and the role of cytotoxic T-lymphocytes and monocytes are more highlighted. Zinc is an imperative element for the growth of epithelium and its deficiency induces the cytotoxic activity of T-helper2 cells, which seems to be associated with lichen planus. This study was aimed to evaluate the levels of serum zinc in erosive and non-erosive oral lichen planus (OLP) and to compare it with the healthy control group to find out any feasible inference. A total of 22 patients with erosive oral lichen planus, 22 patients with non erosive OLP and 44 healthy individuals as the control group were recruited in this descriptive-comparative study. All the participants were selected from the referees to the department of oral medicine, school of dentistry, Tabriz University of Medical Sciences. Serum zinc level was examined for all the individuals with liquid-stat kit (Beckman Instruments Inc.; Carlsbad, CA). Data were analyzed by adopting the ANOVA and Tukey tests, using SPSS 16 statistical software. The mean age of patients with erosive and non-erosive LP was 41.7 and 41.3 years, respectively. The mean age of the healthy control group was 34.4 years .The mean serum zinc levels in the erosive and non erosive lichen planus groups and control groups were 8.3 (1.15), 11.15 (0.92) and 15.74 (1.75) μg/dl respectively. The difference was statistically significant (p< 0.05). The serum zinc levels were decreased in patients with erosive oral lichen planus. This finding may probably indicate the promising role of zinc in development of oral lichen planus.

Pawcatuck and Woonasquatucket River Basins and Narragansett Bay Local Drainage Area. Appendixes.

DTIC Science & Technology

1981-11-01

as to merit no further Federal expenditures . NEW ENGLAND-NEW YORK INTER-AGENCY COMMITTEE REPORT A report by the New England-New York Inter-Agency...quality, flood control, hydroelectric power, navigation, sho-e erosion, fish and wildlife, recreation, historic sites, land management, mineral...navigation improvements, shore erosion protection for selected sites, and increased opportunities for water-oriented recreation, fish and wildlife

Effects of DTM resolution on slope steepness and soil loss prediction on hillslope profiles

Treesearch

Eder Paulo Moreira; William J. Elliot; Andrew T. Hudak

2011-01-01

Topographic attributes play a critical role in predicting erosion in models such as the Water Erosion Prediction Project (WEPP). The effects of four different high resolution hillslope profiles were studied using four different DTM resolutions: 1-m, 3-m, 5-m and 10-m. The WEPP model used a common scenario encountered in the forest environment and the selected hillslope...

Reclamation of skid roads with fiber mats and native vegetation: effects on erosion

Treesearch

shawn T. Grushecky; David w. McGill; William Grafton; John Edwards; Lisa Tager

2007-01-01

A research study was established to test the effectiveness of fiber mats and native seed mixtures in reducing soil erosion from newly-constructed skid roads in the Elk River Watershed in central West Virginia. Twelve road sections of equal grade were paired with a randomly-selected section receiving a fiber mat and native grass seed while the other road section was not...

Road surface erosion on the Jackson Demonstration State Forest: results of a pilot study

Treesearch

Brian Barrett; Rosemary Kosaka; David. Tomberlin

2012-01-01

This paper presents results of a 3 year pilot study of surface erosion on forest roads in the Jackson Demonstration State Forest in California’s coastal redwood region. Ten road segments representing a range of surface, grade, and ditch conditions were selected for the study. At each segment, settling basins with tipping buckets were installed to measure...

Primary prevention of dental erosion by calcium and fluoride: a systematic review.

PubMed

Zini, A; Krivoroutski, Y; Vered, Y

2014-02-01

Overviews of the current literature only provide summaries of existing relevant preventive strategies for dental erosion. To perform a systematic review according to the quantitative meta-analysis method of the scientific literature on prevention of dental erosion. The focused question will address primary prevention of dental erosion by calcium and fluoride. Randomized clinical trials (RCTs) regarding dental erosion prevention. The search included five databases: Embase, Cochrane database of systematic reviews, PubMed (MEDLINE), FDA publication and Berman medical library of the Hebrew University. The search included data in the English language, with effect on preventing dental erosion always presented as mean enamel loss and measured by profilometer. Statistical meta-analysis was performed by StatsDirect program and PEPI statistical software. Fixed- and random-effect models were used to analyse the data. Heterogeneity tests were employed to validate the fixed-effect model assumption. A total of 475 articles on dental erosion prevention were located. A four-stage selection process was employed, and 10 RCT articles were found to be suitable for meta-analysis. The number of studies on prevention of dental erosion maintaining standards of evidence-based dentistry remains insufficient to reach any definite conclusions. The focused questions of this review cannot be addressed according to the existing literature. © 2013 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Changes in particle size distribution of suspended sediment affected by gravity erosion on the Loess Plateau, China

NASA Astrophysics Data System (ADS)

Guo, Wen-Zhao; Xu, Xiang-Zhou; Liu, Ya-Kun; Zhang, Hong-Wu; Zhu, Ming-Dong

2017-04-01

Gravity erosion generates an enormous volume of sediment on the steep hillslopes throughout the world, yet the response from particle size distribution (PSD) of suspended sediment to mass failure remains poorly understood. Here rainfall simulation experiments were conducted on the natural loess slopes to induce a series of mass failures under rainfall intensity of 48 mm h-1, and then an index of enrichment/dilution ratio was used to quantitatively explore the change trend of suspended sediment PSD affected by gravity erosion. To determine suspended sediment, water samples were collected in a polyethylene bottle directly from the gully runoff and channel flow in the pre and during- slope failures events. Then, the particle fractions of samples were done by combining sieving method and photoelectric sedimentometer technique. The results are shown as follows: (1) Gravity erosion has a significant influence on the particle size distribution of suspended sediment. As the mass erosion occurred, the proportion of sand-sized particles was decreased from 71.2 to 50.8%, whereas the proportions of clay and silt were increased remarkably from 1.3 to 7.3% and 27.5 to 41.9%, respectively. Hence the sediment can be more easily transported into channel flow while the suspended sediment load becomes finer as gravitational erosion occurs. (2) The median particle size (d50), sediment heterogeneity (H) and fractal dimensions (D) were significantly correlated with gravity erosion. As a result, d50 was decreased from 0.084 to 0.051 mm, H was increase from 5.6 to 26.8, and D was magnified from 2.60 to 2.78. This implies that mass failure makes the particle size distribution of suspended sediment more nonuniform and irregular. (3) Suspended sediment tended to enrich in the silt and clay fractions, while it diluted in the sand fractions during landslide erosion. Meanwhile, the enrichment/dilution ratios were 13.9 for the clay fractions, 1.4 for clay, and 0.7 for sand. This reflects the particle size selectivity of sediment mobilization on hillslope, and the selectivity of sediment delivery and transport from hillslope to channel. The results have important implications for understanding the connectivity between gravity erosion and sediment discharge to hydrological processes occurring on the hillslope.

Quantifying streambank erosion: a comparative study using an unmanned aerial system (UAS) and a terrestrial laser scanner

NASA Astrophysics Data System (ADS)

Rizzo, D.; Hamshaw, S. D.; Dewoolkar, M.; ONeil-Dunne, J.; Frolik, J.; Bryce, T. G.; Waldron, A. Y.

2015-12-01

Streambank erosion is a common non-point source contributing to suspended sediment and nutrient loading of waterways, and recently has been estimated to account for 30-80% of sediment loading into receiving waters. There is interest in developing reliable methods to quantify bank erosion in watersheds, so effective management strategies can be devised. However, current methods can be either cost prohibitive or unreliable. Direct measurement approaches (surveys and erosion pins) are labor intensive and yield site-specific measurements that are limited for extrapolation to larger scales. Similar issues arise with analytical methods such as slope stability analysis, which require material parameters that are resource intensive to determine. Newer approaches such as use of aerial LiDAR data have proved effective for watershed level assessment, but come with long turnaround times and high cost. Terrestrial laser scanning (TLS) is also effective and offers high accuracy, however collection over large areas is impractical and post-processing is labor intensive. New technology in the form of unmanned aerial systems (UAS) has the potential to significantly enhance the ability to monitor channel migration and quantify bank erosion at variable scales. In this study, 20 km of the Mad and Winooski Rivers in Vermont were flown using a senseFly eBee UAS. Flights were made in spring and fall 2015 in leaf-off conditions with selected portions also flown after large storms in the summer. Change in bank profiles between spring and fall flights provide a comprehensive estimate of bank erosion along the study reaches. Six sites with varying bank heights, erosion sensitivity, and vegetation conditions were selected for simultaneous surveying using a TLS. Point cloud data from both the TLS and UAS were compared to assess the accuracy of the UAS for capturing the bank profile. Changes in bank cross-sections and in volumes calculated from 3D digital surface models were used to compare the UAS and TLS methods. Ascertaining the accuracy of UAS in measuring streambank profiles will determine the appropriateness of the technology for long-term monitoring of bank erosion. The ability for rapid deployment, covering large areas, and fast post-processing allow for more comprehensive monitoring of streambank erosion in river systems.

Holocene evolution of a wave-dominated fan-delta: Godavari delta, India

NASA Astrophysics Data System (ADS)

Saito, Y.; Nageswara Rao, K.; Nagakumar, K.; Demudu, G.; Rajawat, A.; Kubo, S.; Li, Z.

2013-12-01

The Godavari delta is one of the world's largest wave-dominated deltas. The Godavari River arises in the Western Ghats near the west coast of India and drains an area of about 3.1x10^5 km^2, flowing about 1465 km southeast across the Indian peninsula to the Bay of Bengal. The Godavari delta consists of a gentle seaward slope from its apex (12 m elevation) at Rajahmundry and a coastal beach-ridge plain over a distance of about 75 km and covers ~5200 km^2 as a delta plain. The river splits into two major distributary channels, the Gautami and the Vasishta, at a barrage constructed in the mid-1800s. The coastal environment of the deltaic coast is microtidal (~1 m mean tidal range) and wave-dominated (~1.5 m mean wave height in the June-September SW monsoon season, ~0.8 m in the NE monsoon season). Models of the Holocene evolution of the Godavari delta have changed from a zonal progradation model (e.g. Nageswara Rao & Sadakata, 1993) to a truncated cuspate delta model (Nageswara Rao et al., 2005, 2012). Twelve borehole cores (340 m total length), taken in the coastal delta plain during 2010-2013, yielded more than 100 C-14 dates. Sediment facies and C-14 dates from these and previous cores and remote-sensing data support a new delta evolution model. The Holocene coastal delta plain is divided into two parts by a set of linear beach ridges 12-14 km landward from the present shoreline in the central part of the delta. The location of the main depocenter (lobe) has shifted during the Holocene from 1) the center to 2) the west, 3) east, 4) center, 5) west, and 6) east. The linear beach ridges separate the first three from the last three stages. These lobe shifts are controlled by river channel shifts near the apex. Just as the current linear shoreline of the central part of the delta and the concave-up nearshore topography are the result of coastal erosion of a cuspate delta, the linear beach ridges indicate a former eroded shoreline. An unconformity within the deltaic sediments also indicates erosional environments during the formation of the linear shoreline. We interpret this unconformity as a wave-ravinement surface in a regressive delta succession reflecting the decrease of sediment supply due to lobe shifts (or avulsion), and not as a marine erosion surface due to forced regression. Similar erosion surface is recognized in the Yellow River delta (Saito et al., 2000). Discrimination of either surface for ancient sediments and rocks in a wave-dominated setting will be important in sequence-stratigraphic interpretation. Coastal erosion and deposition have occurred in wave-dominated deltas naturally on centennial to millenneial time scales, resulting in delta progradation during the Holocene. However recent decrease of sediment discharge due to dam construction and irrigation on decadal time scales has been exacerbating coastal erosion significantly, resulting in delta shrinking in the Godavari delta. Nageswara Rao, K., Sadakata, N.: In Kay, R. (Ed.), Deltas of the World. American Society of Civil Engineers, New York, 1-15, 1993. Nageswara Rao, K. et al.: In Bhattacharya, J.P., Gioson, L. (Eds.), River Deltas--Concepts, Models and Examples: SEPM Special Publication 83, 435-451, 2005. Nageswara Rao, K. et al.: Geomorphology 175-176, 163¬-175, 2012. Saito, Y. et al.: J Asian Earth Sci. 18, 489-497, 2000.

A comparison of indexing methods to evaluate quality of soils subjected to different erosion: the role of soil microbiological properties.

NASA Astrophysics Data System (ADS)

Romaniuk, Romina; Lidia, Giuffre; Alejandro, Costantini; Norberto, Bartoloni; Paolo, Nannipieri

2010-05-01

Soil quality assessment is needed to evaluate the soil conditions and sustainability of soil and crop management properties, and thus requires a systematic approach to select and interpret soil properties to be used as indicators. The aim of this work was to evaluate and compare different indexing methods to assess quality of an undisturbed grassland soil (UN), a degraded pasture soil (GL) and a no tilled soil (NT) with four different A horizon depths (25, 23, 19 and 14 cm) reflecting a diverse erosion. Twenty four soil properties were measured from 0 to10 (1) and 10 to 20 cm. (2) and a minimum data set was chosen by multivariate principal component analysis (PCA) considering all measured soil properties together (A), or according to their classification in physical, chemical or microbiological (B) properties. The measured soil properties involved either inexpensive or not laborious standard protocols, to be used in routine laboratory analysis (simple soil quality index - SSQI), or a more laborious, time consuming and expensive protocols to determine microbial diversity and microbial functionality by methyl ester fatty acids (PLFA) and catabolic response profiles (CRP), respectively (complex soil quality index - CSQI). The selected properties were linearly normalized and integrated by the weight additive method to calculate SSQI A, SSQI B, CSQI A and CSQI B indices. Two microbiological soil quality indices (MSQI) were also calculated: the MSQI 1 only considered microbiological properties according to the procedure used for calculating SQI; the MSQI 2 was calculated by considering microbial carbon biomass (MCB), microbial activity (Resp) and functional diversity determined by CPR (E). The soil quality indices were SSQI A = MCB 1 + Particulate Organic Carbon (POC)1 + Mean Weight Diameter (MWD)1; SSQI B = Saturated hydraulic conductivity (K) 1 + Total Organic Carbon (TOC) 1 + MCB 1; CSQI A = MCB 1 + POC 1 + MWD 1; CSQI B = K 1+ TOC 1+ 0.3 * (MCB 1+ i/a +POC 1) + 0,05 * (E + cy/pre), where i/a and cy/pre are the iso/anteiso and cyclopropyl/precursors ratios determined by PLFA; MSQI 1 (0,3 * (MCB 1+ i/a 1 +POC 1) + 0,05 * (E 1+ cy/pre 1) ) and MSQI 2 (MCB 1+Resp 1+ E 1). All the calculated indices differentiated references plots (UN and GL), from those under no tillage (NT) system. Values were similar in NT plots with low erosion levels (NT 25 and 23) but higher than values of plots with high erosion (NT 19 and 14). Soil quality indices constructed by procedure B, (SSQI B and CSQI B) differentiated among the studied plots with the same or higher sensitivity than the other indices and allowed evaluating the impact of soil management practices and erosion on soil physical, chemical and microbiological properties. The lack of indicators representing all soil properties (physical, chemical and biological) in SQI constructed by procedure A could decrease the index sensitivity to changes in management; and the same may happen when physical, chemical and biological properties present different weights into the calculated SQI. The inclusion of CRP and PLFA data in the indices slightly increased or did not increase the index sensitivity (CSQI A and CSQI B). Generally microbiological indices (MSQI 1 and MSQI 2) were highly sensitive to soil erosion. However, we suggest that indices integrating physical, chemical and microbiological properties may give a more complete view of the soil quality than indices only based on measurement of a few microbiological properties.

Climate-change impacts on terrestrial ecosystems and water resources at different global warming levels

NASA Astrophysics Data System (ADS)

Tanaka, A.; Takahashi, K.; Shiogama, H.; Hanasaki, N.; Masaki, Y.; Ito, A.; Noda, H.; Hijioka, Y.; Emori, S.

2016-12-01

The Paris Agreement of 2015 includes pursuing efforts to limit the increase in the global mean temperature from preindustrial levels (ΔGMT) to 1.5°C, as well as suppressing ΔGMT well below 2°C. However, how impacts of 1.5°C differ from the impacts of 2°C or greater warming is unclear, and further studies covering wider ranges of ΔGMT are required. We arranged climate-change impacts at different ΔGMT levels by employing the outputs from impact assessment simulations based on climate scenarios of five climate models and four radiative forcing scenarios. We then tested whether climate-change impacts at different ΔGMT levels in a range ΔGMT = 1.5-4°C can be derived from those at ΔGMT = 2°C by linear scaling. We assessed impacts on net primary production, CO2 emissions from biomass burning, soil erosion, and surface runoff, at global and regional scales. We found that linearity holds in most regions for net primary production, biomass burning, and surface runoff, but fails for soil erosion. In this session, we discuss at what value of ΔGMT linearity fails for both world and several regional domains.

Effects of vegetation on runoff generation, sediment yield and soil shear strength on road-side slopes under a simulation rainfall test in the Three Gorges Reservoir Area, China.

PubMed

Liu, Yao-Jun; Wang, Tian-Wei; Cai, Chong-Fa; Li, Zhao-Xia; Cheng, Dong-Bing

2014-07-01

Vegetation recolonization has often been used to control roadside slope erosion, and in this paper, four restoration models - Natural Restoration, Grass, Grass & Shrub, Sodded Strip - were chosen to recolonize the plants on a newly built unpaved roadside slope in the Three Gorges Reservoir Area. After eight months growth, eight rainfall simulations (intensity of 90 mm h(-1) for 60 min) and in-situ soil shear strength test were then carried out to identify the impacts of vegetation on roadside slope erosion and soil shear strength. The erosion on cutslopes was higher than that on fillslopes. The runoff coefficient and soil detachment rate were significantly lower on the Grass & Shrub model (4.3% and 1.99 g m(-2) min(-1), respectively) compared with the other three, which had the highest surface cover (91.4%), aboveground biomass (1.44 kg m(-2)) and root weight density (3.94 kg m(-3)). The runoff coefficient and soil detachment rate on roadside slopes showed a logarithmic decrease with the root weight density, root length density and aboveground biomass. The soil shear strength measured before and after the rainfall was higher on Grass & Shrub (59.29 and 53.73 kPa) and decreased on Grass (46.93 and 40.48 kPa), Sodded Strip (31.20 and 18.87 kPa) and Natural Restoration (25.31 and 9.36 kPa). Negative linear correlations were found between the soil shear strength reduction and aboveground biomass, root weight density and root length density. The variation of soil shear strength reduction was closely related to the roadside slope erosion, a positive linear correlation was found between runoff coefficient and soil shear strength reduction, and a power function was shown between soil detachment rate and soil shear strength reduction. This study demonstrated that Grass and Grass & Shrub were more suitable and highly cost-effective in controlling initial period erosion of newly built low-volume unpaved road. Copyright © 2014 Elsevier B.V. All rights reserved.

Erodibility of waste (Loess) soils from construction sites under water and wind erosional forces.

PubMed

Tanner, Smadar; Katra, Itzhak; Argaman, Eli; Ben-Hur, Meni

2018-03-01

Excess soils from construction sites (waste soils) become a problem when exposed to soil erosion by water or wind. Understanding waste soil erodibility can contribute to its proper reuse for various surface applications. The general objective of the study was to provide a better understanding of the effects of soil properties on erodibility of waste soils excavated from various depths in a semiarid region under rainfall and wind erosive forces. Soil samples excavated from the topsoil (0-0.3m) and subsoil layers (0.3-0.9 and >1m depths) were subjected to simulated rainfall and wind. Under rainfall erosive forces, the subsoils were more erodible than the topsoil, in contrast to the results obtained under wind erosive forces. Exchangeable sodium percentage was the main factor controlling soil erodibility (K i ) under rainfall, and a significant logarithmic regression line was found between these two parameters. In addition, a significant, linear regression was found between K i and slaking values for the studied soil samples, suggesting that the former can be predicted from the latter. Soil erodibility under wind erosion force was controlled mainly by the dry aggregate characteristics (mean weight diameter and aggregate density): their higher values in the subsoil layers resulted in lower soil erodibility compared to the topsoil. Copyright © 2017 Elsevier B.V. All rights reserved.

Comparison of clinical burden between patients with erosive hand osteoarthritis and inflammatory arthritis in symptomatic community-dwelling adults: the Keele clinical assessment studies

PubMed Central

Kloppenburg, Margreet; Marshall, Michelle; Nicholls, Elaine; Rosendaal, Frits R.; van der Windt, Danielle A.; Peat, George

2013-01-01

Objective. To investigate in the general population the clinical impact of erosive OA in interphalangeal joints (IPJs) compared with symptomatic radiographic hand OA and inflammatory arthritis. Methods. Standardized assessments with hand radiographs were performed in participants of two population-based cohorts in North Staffordshire with hand symptoms lasting ≥1 day in the past month. Erosive OA was defined as the presence of an eroded or remodelled phase in ≥1 IPJ using the Verbruggen–Veys method. Radiographic hand OA was defined as the presence of ≥1 IPJ/first carpometacarpal joint with a Kellgren–Lawrence score of ≥2. Diagnoses of inflammatory arthritis were based on medical records. Hand pain and disability were assessed with the Australian/Canadian Hand Osteoarthritis Index (AUSCAN). Linear regression analyses were used to compare clinical determinants between groups and calculate mean differences with 95% CIs, adjusted for age and sex. Results. Of 1076 participants with hand symptoms [60% women, mean age 64.8 years (s.d. 8.3 years)]; 80 persons (7.4%) had erosive OA. The population prevalence of erosive OA in ≥1 IPJ was 2.4% (95% CI 1.8, 3.0). Persons with erosive OA reported more pain and disability than persons with symptomatic radiographic hand OA [adjusted mean difference 1.3 (95% CI 0.3, 2.3) and 2.3 (95% CI 0.4, 4.2), respectively]. Individuals with inflammatory arthritis (n = 44) reported more pain and disability than those with erosive OA [adjusted mean difference 1.7 (95% CI 0.05, 3.4) and 6.3 (95% CI 2.8, 9.9), respectively]. Conclusion. While erosive OA has a greater impact than symptomatic radiographic hand OA in the general population, it is not as severe in terms of hand pain and disability as inflammatory RA. PMID:24046470

A quantitative study of gully erosion based on object-oriented analysis techniques: a case study in Beiyanzikou catchment of Qixia, Shandong, China.

PubMed

Wang, Tao; He, Fuhong; Zhang, Anding; Gu, Lijuan; Wen, Yangmao; Jiang, Weiguo; Shao, Hongbo

2014-01-01

This paper took a subregion in a small watershed gully system at Beiyanzikou catchment of Qixia, China, as a study and, using object-orientated image analysis (OBIA), extracted shoulder line of gullies from high spatial resolution digital orthophoto map (DOM) aerial photographs. Next, it proposed an accuracy assessment method based on the adjacent distance between the boundary classified by remote sensing and points measured by RTK-GPS along the shoulder line of gullies. Finally, the original surface was fitted using linear regression in accordance with the elevation of two extracted edges of experimental gullies, named Gully 1 and Gully 2, and the erosion volume was calculated. The results indicate that OBIA can effectively extract information of gullies; average range difference between points field measured along the edge of gullies and classified boundary is 0.3166 m, with variance of 0.2116 m. The erosion area and volume of two gullies are 2141.6250 m(2), 5074.1790 m(3) and 1316.1250 m(2), 1591.5784 m(3), respectively. The results of the study provide a new method for the quantitative study of small gully erosion.

Impact erosion prediction using the finite volume particle method with improved constitutive models

NASA Astrophysics Data System (ADS)

Leguizamón, Sebastián; Jahanbakhsh, Ebrahim; Maertens, Audrey; Vessaz, Christian; Alimirzazadeh, Siamak; Avellan, François

2016-11-01

Erosion damage in hydraulic turbines is a common problem caused by the high- velocity impact of small particles entrained in the fluid. In this investigation, the Finite Volume Particle Method is used to simulate the three-dimensional impact of rigid spherical particles on a metallic surface. Three different constitutive models are compared: the linear strainhardening (L-H), Cowper-Symonds (C-S) and Johnson-Cook (J-C) models. They are assessed in terms of the predicted erosion rate and its dependence on impact angle and velocity, as compared to experimental data. It has been shown that a model accounting for strain rate is necessary, since the response of the material is significantly tougher at the very high strain rate regime caused by impacts. High sensitivity to the friction coefficient, which models the cutting wear mechanism, has been noticed. The J-C damage model also shows a high sensitivity to the parameter related to triaxiality, whose calibration appears to be scale-dependent, not exclusively material-determined. After calibration, the J-C model is capable of capturing the material's erosion response to both impact velocity and angle, whereas both C-S and L-H fail.

Impacts of changing hydrology on permanent gully growth: experimental results

NASA Astrophysics Data System (ADS)

Day, Stephanie S.; Gran, Karen B.; Paola, Chris

2018-06-01

Permanent gullies grow through head cut propagation in response to overland flow coupled with incision and widening in the channel bottom leading to hillslope failures. Altered hydrology can impact the rate at which permanent gullies grow by changing head cut propagation, channel incision, and channel widening rates. Using a set of small physical experiments, we tested how changing overland flow rates and flow volumes alter the total volume of erosion and resulting gully morphology. Permanent gullies were modeled as both detachment-limited and transport-limited systems, using two different substrates with varying cohesion. In both cases, the erosion rate varied linearly with water discharge, such that the volume of sediment eroded was a function not of flow rate, but of total water volume. This implies that efforts to reduce peak flow rates alone without addressing flow volumes entering gully systems may not reduce erosion. The documented response in these experiments is not typical when compared to larger preexisting channels where higher flow rates result in greater erosion through nonlinear relationships between water discharge and sediment discharge. Permanent gullies do not respond like preexisting channels because channel slope remains a free parameter and can adjust relatively quickly in response to changing flows.

Analysis of Artificial Neural Network in Erosion Modeling: A Case Study of Serang Watershed

NASA Astrophysics Data System (ADS)

Arif, N.; Danoedoro, P.; Hartono

2017-12-01

Erosion modeling is an important measuring tool for both land users and decision makers to evaluate land cultivation and thus it is necessary to have a model to represent the actual reality. Erosion models are a complex model because of uncertainty data with different sources and processing procedures. Artificial neural networks can be relied on for complex and non-linear data processing such as erosion data. The main difficulty in artificial neural network training is the determination of the value of each network input parameters, i.e. hidden layer, momentum, learning rate, momentum, and RMS. This study tested the capability of artificial neural network application in the prediction of erosion risk with some input parameters through multiple simulations to get good classification results. The model was implemented in Serang Watershed, Kulonprogo, Yogyakarta which is one of the critical potential watersheds in Indonesia. The simulation results showed the number of iterations that gave a significant effect on the accuracy compared to other parameters. A small number of iterations can produce good accuracy if the combination of other parameters was right. In this case, one hidden layer was sufficient to produce good accuracy. The highest training accuracy achieved in this study was 99.32%, occurred in ANN 14 simulation with combination of network input parameters of 1 HL; LR 0.01; M 0.5; RMS 0.0001, and the number of iterations of 15000. The ANN training accuracy was not influenced by the number of channels, namely input dataset (erosion factors) as well as data dimensions, rather it was determined by changes in network parameters.

Statistics of rocky coast erosion and percolation theory

NASA Astrophysics Data System (ADS)

Baldassarri, A.; Sapoval, B.

2012-04-01

The dynamics of rocky coasts is an erratic phenomenon featuring numerous small erosion events, but sometimes large dramatic collapses. In this sense, its study should not limit or rely on average erosion rates. Recent studies, based on historical as well as recent data, have indicated that the frequency of magnitude of erosion events display long tail distribution, similar to what observed in landslide. In other words the time evolution of a coast morphology does not enter the classical category of Gaussian process, but rather that of critical systems in physics. We recently proposed a minimal dynamical model of rocky coast erosion which is able to reproduce the diversity of rocky coast morphologies and their dynamics. This model is based on a single, simple ingredient, the retroaction of the coast morphology on the erosive power of the sea. It follows from the idea that erosion can spontaneously create irregular seashores, but, in turn, the geometrical irregularity of the coast participates to the damping of sea-waves, decreasing the average wave amplitude and erosive power. The resulting mutual self-stabilization dynamics of the sea erosion power and coastal irregular morphology leads spontaneously the system to a critical dynamics. Our results indicate then that rocky coast erosion and the statistical theory of percolation are closely related. In this framework, the sometimes fractal geometry of coastlines can be recovered and understood in terms of fractal dimension of the external perimeter of a percolation cluster. From a more practical point of view, the analogy with percolation interfaces means that the coast constitutes a strong, but possibly fragile, barrier to sea erosion, emerging from a self-organised selection process. Accordingly, the effect of a slow weathering degradation of the rocks mechanical properties, as well as other perturbations from natural or human cause, can trigger random and large erosion events difficult to predict and control. To the extent that these ideas apply, natural coasts should be "preserved" and managed with care.

Soil carbon storages and erosional exports along a forested denudation gradient in the Sierra Nevada, California

NASA Astrophysics Data System (ADS)

Yoo, K.; Wang, X.; Mudd, S. M.; Weinman, B.; Gutknecht, J.; Gabet, E. J.

2017-12-01

Eroding uplands not only provide physically mixed soil zones where OC and minerals actively interact but also are the significant sources of suspended sediments and organic carbon (OC) to rivers. Here our goal is to quantify the extents that erosion affects soils' capacities to store OC in different degrees of mineral-association and to facilitate the exports of minerals that might capture OC on their reactive surfaces. We examined a tributary basin to the Middle Folk Feather River in California, where knickpoint migration has created a series of hillslopes with erosion rates varying from 35 to 250 mm kyr-1. Other than erosion rates, the studied hillslopes within the tributary basin shared similar environmental factors. Soil samples were collected from select hillslopes that differ in their relative positions to knikpoints and were subject to size and density fractionation. Despite the substantial difference in erosion rates, concentrations of particulate OC (POC) and mineral-associated OC (MOC) and soil thickness varied little. Instead, considerable increase in coarse rock contents positively associated with erosion rate was responsible for the reduction of soil OC inventories by 37% with increasing erosion rate. In contrast to consistent MOC concentrations across the erosion gradient, clay contents in soils are negatively correlated with erosion rates. This seemingly contradictory result, however, is consistent with BET mineral specific surface area that remains insensitive to erosion rates. OC coverage on mineral surface was found to be less than < 50%, indicating that eroded minerals would have a significant, and currently unknown, capacity to adsorb additional OC during their transport to sediment sinks. This study thus reveals that mineral weathering acts as an important filter through which erosion affects the soil carbon cycle.

Estimates of soil erosion using cesium-137 tracer models.

PubMed

Saç, M M; Uğur, A; Yener, G; Ozden, B

2008-01-01

The soil erosion was studied by 137Cs technique in Yatagan basin in Western Turkey, where there exist intensive agricultural activities. This region is subject to serious soil loss problems and yet there is not any erosion data towards soil management and control guidelines. During the soil survey studies, the soil profiles were examined carefully to select the reference points. The soil samples were collected from the slope facets in three different study areas (Kirtas, Peynirli and Kayisalan Hills). Three different models were applied for erosion rate calculations in undisturbed and cultivated sites. The profile distribution model (PDM) was used for undisturbed soils, while proportional model (PM) and simplified mass balance model (SMBM) were used for cultivated soils. The mean annual erosion rates found using PDM in undisturbed soils were 15 t ha(-1) year(-1) at the Peynirli Hill and 27 t ha(-1) year(-1) at the Kirtas Hill. With the PM and SMBM in cultivated soils at Kayişalan, the mean annual erosion rates were obtained to be 65 and 116 t ha(-1) year(-1), respectively. The results of 137Cs technique were compared with the results of the Universal Soil Loss Equation (USLE).

Soil erosion and the global carbon budget.

PubMed

Lal, R

2003-07-01

Soil erosion is the most widespread form of soil degradation. Land area globally affected by erosion is 1094 million ha (Mha) by water erosion, of which 751 Mha is severely affected, and 549 Mha by wind erosion, of which 296 Mha is severely affected. Whereas the effects of erosion on productivity and non-point source pollution are widely recognized, those on the C dynamics and attendant emission of greenhouse gases (GHGs) are not. Despite its global significance, erosion-induced carbon (C) emission into the atmosphere remains misunderstood and an unquantified component of the global carbon budget. Soil erosion is a four-stage process involving detachment, breakdown, transport/redistribution and deposition of sediments. The soil organic carbon (SOC) pool is influenced during all four stages. Being a selective process, erosion preferentially removes the light organic fraction of a low density of <1.8 Mg/m(3). A combination of mineralization and C export by erosion causes a severe depletion of the SOC pool on eroded compared with uneroded or slightly eroded soils. In addition, the SOC redistributed over the landscape or deposited in depressional sites may be prone to mineralization because of breakdown of aggregates leading to exposure of hitherto encapsulated C to microbial processes among other reasons. Depending on the delivery ratio or the fraction of the sediment delivered to the river system, gross erosion by water may be 75 billion Mg, of which 15-20 billion Mg are transported by the rivers into the aquatic ecosystems and eventually into the ocean. The amount of total C displaced by erosion on the earth, assuming a delivery ratio of 10% and SOC content of 2-3%, may be 4.0-6.0 Pg/year. With 20% emission due to mineralization of the displaced C, erosion-induced emission may be 0.8-1.2 Pg C/year on the earth. Thus, soil erosion has a strong impact on the global C cycle and this component must be considered while assessing the global C budget. Adoption of conservation-effective measures may reduce the risks of C emission and sequester C in soil and biota.

Dental erosion in groups of Yemeni children and adolescents and the modification of an erosion partial recording system.

PubMed

Al-Ashtal, Amin; Johansson, Anders; Omar, Ridwaan; Johansson, Ann-Katrin

2017-07-01

The prevalence of dental erosion is rising especially among children and adolescents and its grading needs further investigation. To determine the prevalence and severity of dental erosion in groups of Yemeni children and adolescents, and to clinically compare an erosion partial recording system (EPRS) with a proposed modified-simplified version (EPRS-M). Of 6163 individuals aged 5-6, 13-14 and 18-19 years, 911 were randomly selected, of which 668 participated in the study. Dental erosion was graded using EPRS. EPRS-M was proposed, and its sensitivity and specificity was calculated in relation to EPRS. Prevalence of erosion extending into dentine on at least one tooth was 6.8% among 5- to 6-year-olds, 3.0% among 13- to 14-year-olds and 14.6% among 18- to 19-year olds. The highest prevalence was 19.2% among girls aged 18-19 years which was significantly higher than boys (10.4%) in the same age group (P = 0.044). Sensitivity and specificity for EPRS-M in relation to EPRS were 85.7% and 100% for primary teeth, and 84.1% and 100% for permanent teeth. Dental erosion was common among children and older teenagers and highest among older girls but less common among younger teenagers. The tested accuracy of EPRS-M qualifies it to be used as an initial quick detection tool in future dental erosion research. © 2016 The Authors. International Journal of Paediatric Dentistry published by BSPD, IAPD and John Wiley & Sons Ltd.

New Active Optical Technique Developed for Measuring Low-Earth-Orbit Atomic Oxygen Erosion of Polymers

NASA Technical Reports Server (NTRS)

Banks, Bruce A.; deGroh, Kim K.; Demko, Rikako

2003-01-01

Polymers such as polyimide Kapton (DuPont) and Teflon FEP (DuPont, fluorinated ethylene propylene) are commonly used spacecraft materials because of desirable properties such as flexibility, low density, and in the case of FEP, a low solar absorptance and high thermal emittance. Polymers on the exterior of spacecraft in the low-Earth-orbit (LEO) environment are exposed to energetic atomic oxygen. Atomic oxygen reaction with polymers causes erosion, which is a threat to spacecraft performance and durability. It is, therefore, important to understand the atomic oxygen erosion yield E (the volume loss per incident oxygen atom) of polymers being considered in spacecraft design. The most common technique for determining E is a passive technique based on mass-loss measurements of samples exposed to LEO atomic oxygen during a space flight experiment. There are certain disadvantages to this technique. First, because it is passive, data are not obtained until after the flight is completed. Also, obtaining the preflight and postflight mass measurements is complicated by the fact that many polymers absorb water and, therefore, the mass change due to water absorption can affect the E data. This is particularly true for experiments that receive low atomic oxygen exposures or for samples that have a very low E. An active atomic oxygen erosion technique based on optical measurements has been developed that has certain advantages over the mass-loss technique. This in situ technique can simultaneously provide the erosion yield data on orbit and the atomic oxygen exposure fluence, which is needed for erosion yield determination. In the optical technique, either sunlight or artificial light can be used to measure the erosion of semitransparent or opaque polymers as a result of atomic oxygen attack. The technique is simple and adaptable to a rather wide range of polymers, providing that they have a sufficiently high optical absorption coefficient. If one covers a photodiode with a uniformly thick sheet of semitransparent polymer such as Kapton H polyimide, then as atomic oxygen erodes the polymer, the short-circuit current from the photodiode will increase in an exponential manner with fluence. This nonlinear response with fluence results in a lack of sensitivity for measuring low atomic oxygen fluences. However, if one uses a variable-thickness polymer or carbon sample, which is configured as shown in the preceding figure, then a linear response can be achieved for opaque materials using a parabolic well for a circular geometry detector or a V-shaped well for a rectangular-geometry detector. Variable-thickness samples can be fabricated using many thin polymer layers. For semitransparent polymers such as Kapton H polyimide, there is an initial short-circuit current that is greater than zero. This current has a slightly nonlinear dependence on atomic oxygen fluence in comparison to opaque materials such as black Kapton as shown in the graph. For this graph figure, the total thickness of Kapton H was assumed to be 0.03 cm. The photodiode short-circuit current shown in the graph was generated on the basis of preliminary measurements-a total reflectance rho of 0.0424 and an optical absorption coefficient a of 146.5 cm(sup -1). In addition to obtaining on-orbit data, the advantage of this active erosion and erosion yield measurement technique is its simplicity and reliance upon well-characterized fluence witness materials as well as a nearly linear photodiode short-circuit current dependence upon atomic oxygen fluence. The optical technique is useful for measuring either atomic oxygen fluence or erosion, depending on the information desired. To measure the atomic oxygen erosion yield of a test material, one would need to have two photodiode sensors, one for the test material and one that uses a known erosion yield material (such as Kapton) to measure the atomic oxygen fluence.

Comparative effects of oil palm and selective logging on erosion, river channels and water chemistry in Malaysian steeplands

NASA Astrophysics Data System (ADS)

Walsh, Rory; Nainar, Anand; Nurhidayu, Siti; Higton, Sam; Annammala, Kogilavani; Wall, Katy; Bidin, Kawi; Blake, William; Darling, Isabella

2017-04-01

Oil palm land-use has expanded greatly in recent decades in SE Asia and other parts of the wet tropics, including to steepland areas, where bench-terraced landscaping is involved. Retaining (and sometimes restoring) riparian forest strips and rainforest fragments on the steepest slopes have been adopted as elements of strategies designed to reduce adverse effects on runoff generation, erosion, downstream sedimentation, flooding and pollutional problems - as well as biodiversity and emissions. Results of catchment monitoring, soil erosion and sediment fingerprinting research in oil palm and selectively logged steeplands of eastern Sabah and Peninsular Malaysia are presented. The evidence indicates the greater scale and temporal persistence of effects that oil palm land-use (compared with selective logging) has had on suspended sediment dynamics, soil erosion, downstream sedimentation, channel geometry and dynamics and river pollution. The importance of (1) high densities of roads and tracks and (2) relatively impermeable bench-terraced terrain in enhancing runoff, sediment and nutrient outputs in storm events is stressed. Influences of oil palm management practices including riparian forest strips in increasing or reducing these effects are critically reviewed and ways of increasing the effectiveness of riparian forest strips are proposed. The design and rationale of current projects exploring and testing consequences of existing and proposed improved land management practices are briefly described. The key importance of involvement of people from the oil palm industry (including multinational companies, smallholders and their organizations) and Government bodies that are responsible for land-use policies and land management practices is stressed.

Experimental rill erosion research vs. model concepts - quantification of the hydraulic and erosional efficiency of rills

NASA Astrophysics Data System (ADS)

Wirtz, Stefan

2014-05-01

In soil erosion research, rills are believed to be one of the most efficient forms. They act as preferential flow paths for overland flow and hence become the most efficient sediment sources in a catchment. However their fraction of the overall detachment in a certain area compared to other soil erosion processes is contentious. The requirement for handling this subject is the standardization of the used measurement methods for rill erosion quantification. Only by using a standardized method, the results of different studies become comparable and can be synthesized to one overall statement. In rill erosion research, such a standardized field method was missing until now. Hence, the first aim of this study is to present an experimental setup that enables us to obtain comparable data about process dynamics in eroding rills under standardized conditions in the field. Using this rill experiment, the runoff efficiency of rills (second aim) and the fraction of rill erosion on total soil loss (third aim) in a catchment are quantified. The erosion rate [g m-2] in the rills is between twenty- and sixty-times higher compared to the interrill areas, the specific discharge [L s-1 m-2] in the rills is about 2000 times higher. The identification and quantification of different rill erosion processes are the fourth aim within this project. Gravitative processes like side wall failure, headcut- and knickpoint retreat provide up to 94 % of the detached sediment quantity. In soil erosion models, only the incision into the rill's bottom is considered, hence the modelled results are unsatisfactorily. Due to the low quality of soil erosion model results, the fifth aim of the study is to review two physical basic assumptions using the rill experiments. Contrasting with the model assumptions, there is no clear linear correlation between any hydraulic parameter and the detachment rate and the transport rate is capable of exceeding the transport capacity. In conclusion, the results clearly show the need of experimental field data obtained under conditions as close as possible to reality. This is the only way to improve the fundamental knowledge about the function and the impact of the different processes in rill erosion. A better understanding of the process combinations is a fundamental request for developing a really functioning soil erosion model. In such a model, spatial and temporal variability as well as the combination of different sub-processes must be considered. Regarding the experimental results of this study, the simulation of natural processes using simple, static mathematical equations seems not to be possible.

When more is actually less-the tale of chronic ammonia toxicity

USDA-ARS?s Scientific Manuscript database

A commercial catfish producer submitted 7 food-sized fish from a pond that was experiencing mortalities on Jan 24, 2014. The ~ 2.64 acre pond was stocked with hybrid catfish. No gross external lesions were evident except for linear erosions (scratches) on the skin that were thought iatrogenic in or...

Experimental Setup for Evaluation of the Protective Technical Measures Against the Slopes Degradation Along Linear Construction Sites

NASA Astrophysics Data System (ADS)

Kavka, Petr; Zumr, David; Neumann, Martin; Lidmila, Martin; Dufka, Dušan

2017-04-01

Soil erosion of the slopes along the linear construction sites, such as railroads, roads, pipelines or watercourses, is usually underestimated by the construction companies and controlling authorities. But under certain circumstances, when the construction site is not maintained and protected properly, a large amounts of soil may be transported from the sites to the surrounding environment during the intensive rainfall. Transported sediment, often carrying adsorbed pollutants, may reach watercourses and cause water recipient siltation and pollution. Within the applied research project we investigate ways of low cost, quick and easy technical measures that would help to protect the slopes against the splash erosion, rills development and sliding. The methodology is based on testing of various permeable covers, sheets, anchoring and patchy vegetation on a plot and hillslope scales. In this contribution we will present the experimental plot setup, consisting of large soil blocks encapsulated in the monitored steel containers and nozzle rainfall simulator. The presentation is funded by the Technological Agency of the Czech Republic (research project TH02030428) and an internal student CTU grant.

A geomorphic process law for detachment-limited hillslopes

NASA Astrophysics Data System (ADS)

Turowski, Jens

2015-04-01

Geomorphic process laws are used to assess the shape evolution of structures at the Earth's surface over geological time scales, and are routinely used in landscape evolution models. There are two currently available concepts on which process laws for hillslope evolution rely. In the transport-limited concept, the evolution of a hillslope is described by a linear or a non-linear diffusion equation. In contrast, in the threshold slope concept, the hillslope is assumed to collapse to a slope equal to the internal friction angle of the material when the load due to the relief exists the material strength. Many mountains feature bedrock slopes, especially in the high mountains, and material transport along the slope is limited by the erosion of the material from the bedrock. Here, I suggest a process law for detachment-limited or threshold-dominated hillslopes, in which the erosion rate is a function of the applied stress minus the surface stress due to structural loading. The process law leads to the prediction of an equilibrium form that compares well to the shape of many mountain domes.

Is the use of esomeprazole in gastroesophageal reflux disease a cost-effective option in Poland?

PubMed

Petryszyn, Pawel; Staniak, Aleksandra; Grzegrzolka, Jedrzej

2016-03-01

To compare the cost-effectiveness of therapy of gastroesophageal reflux disease with esomeprazole and other proton pump inhibitors (PPIs) in Poland. Studies comparing esomeprazole with other PPIs in the treatment of erosive esophagitis, non-erosive reflux disease and gastroesophageal reflux disease maintenance therapy were systematically reviewed. 9 randomized clinical trials were selected, meta-analyses were conducted. Cost data derived from Polish Ministry of Health and Pharmacies in Wroclaw. In the treatment of erosive esophagitis esomeprazole was significantly more effective than other PPIs. Both for 4- and 8-week therapy respective incremental cost-effectiveness ratio values were acceptably low. Differences in effectiveness of non-erosive reflux disease therapy were not significant. The replacement of pantoprazole 20 mg with more effective esomeprazole 20 mg in the 6-month maintenance therapy was associated with a substantially high incremental cost-effectiveness ratio.

Materials for Advanced Turbine Engines (MATE). Project 4: Erosion resistant compressor airfoil coating

NASA Technical Reports Server (NTRS)

Rashid, J. M.; Freling, M.; Friedrich, L. A.

1987-01-01

The ability of coatings to provide at least a 2X improvement in particulate erosion resistance for steel, nickel and titanium compressor airfoils was identified and demonstrated. Coating materials evaluated included plasma sprayed cobalt tungsten carbide, nickel carbide and diffusion applied chromium plus boron. Several processing parameters for plasma spray processing and diffusion coating were evaluated to identify coating systems having the most potential for providing airfoil erosion resistance. Based on laboratory results and analytical evaluations, selected coating systems were applied to gas turbine blades and evaluated for surface finish, burner rig erosion resistance and effect on high cycle fatigue strength. Based on these tests, the following coatings were recommended for engine testing: Gator-Gard plasma spray 88WC-12Co on titanium alloy airfoils, plasma spray 83WC-17Co on steel and nickel alloy airfoils, and Cr+B on nickel alloy airfoils.

Multifractal Model of Soil Water Erosion

NASA Astrophysics Data System (ADS)

Oleshko, Klaudia

2017-04-01

Breaking of solid surface symmetry during the interaction between the rainfall of high erosivity index and internally unstable volcanic soil/vegetation systems, results in roughness increasing as well as fertile horizon loosing. In these areas, the sustainability of management practices depends on the ability to select and implement the precise indicators of soil erodibility and vegetation capacity to protect the system against the extreme damaging precipitation events. Notwithstanding, the complex, non-linear and scaling nature of the phenomena involved in the interaction among the soil, vegetation and precipitation is still not taken into account by the numerous commonly used empirical, mathematical and computer simulation models: for instance, by the universal soil loss equation (USLE). The soil erodibility factor (K-factor) is still measuring by a set of empirical, dimensionless parameters and indexes, without taking into account the scaling (frequently multifractal) origin of a broad range of heterogeneous, anisotropic and dynamical phenomena involved in hydric erosion. Their mapping is not representative of this complex system spatial variability. In our research, we propose to use the toolbox of fractals and multifractals techniques in vista of its ability to measure the scale invariance and type/degree of soil, vegetation and precipitation symmetry breaking. The hydraulic units are chosen as the precise measure of soil/vegetation stability. These units are measured and modeled for soils with contrasting architecture, based on their porosity/permeability (Poroperm) as well as retention capacity relations. The simple Catalog of the most common Poroperm relations is proposed and the main power law relations among the elements of studied system are established and compared for some representative agricultural and natural Biogeosystems of Mexico. All resulted are related with the Mandelbrot' Baby Theorem in order to construct the universal Phase Diagram which graphically represents the critical points of the dynamics of soil erodibility as function of the vegetation cover and precipitation parameters.

Deployment Area Selection and Land Withdrawal/Acquisition. M-X/MPS (M-X/Multiple Protective Shelter) Environmental Technical Report. Mitigations.

DTIC Science & Technology

1981-10-02

structure. Compacted soils are difficult to revegetate without adequate treatment . In addition, compacted soils have lower infiltration rates * which result...Reno, Nevada. August 1976). Erosion and sediment can be controlled on construction sites if certain principles are followed in the use of treatment of...If successful erosion control treatment is applied to the land in the watershed, sediment production can be reduced to

A fuzzy multi-objective linear programming approach for integrated sheep farming and wildlife in land management decisions: a case study in the Patagonian rangelands

NASA Astrophysics Data System (ADS)

Metternicht, Graciela; Blanco, Paula; del Valle, Hector; Laterra, Pedro; Hardtke, Leonardo; Bouza, Pablo

2015-04-01

Wildlife is part of the Patagonian rangelands sheep farming environment, with the potential of providing extra revenue to livestock owners. As sheep farming became less profitable, farmers and ranchers could focus on sustainable wildlife harvesting. It has been argued that sustainable wildlife harvesting is ecologically one of the most rational forms of land use because of its potential to provide multiple products of high value, while reducing pressure on ecosystems. The guanaco (Lama guanicoe) is the most conspicuous wild ungulate of Patagonia. Guanaco ?bre, meat, pelts and hides are economically valuable and have the potential to be used within the present Patagonian context of production systems. Guanaco populations in South America, including Patagonia, have experienced a sustained decline. Causes for this decline are related to habitat alteration, competition for forage with sheep, and lack of reasonable management plans to develop livelihoods for ranchers. In this study we propose an approach to explicitly determinate optimal stocking rates based on trade-offs between guanaco density and livestock grazing intensity on rangelands. The focus of our research is on finding optimal sheep stocking rates at paddock level, to ensure the highest production outputs while: a) meeting requirements of sustainable conservation of guanacos over their minimum viable population; b) maximizing soil carbon sequestration, and c) minimizing soil erosion. In this way, determination of optimal stocking rate in rangelands becomes a multi-objective optimization problem that can be addressed using a Fuzzy Multi-Objective Linear Programming (MOLP) approach. Basically, this approach converts multi-objective problems into single-objective optimizations, by introducing a set of objective weights. Objectives are represented using fuzzy set theory and fuzzy memberships, enabling each objective function to adopt a value between 0 and 1. Each objective function indicates the satisfaction of the decision maker towards the respective objective. Fuzzy logic is closer to intuitive thinking used by decision makers, making it a user-friendly approach for them to select alternatives. The proposed approach was applied in a study area of approximately 40,000 hectares in semiarid Patagonian rangelands where extensive, continuous sheep grazing for wool production is the main land use. Multi- and hyper-spectral data were combined with ancillary data within a GIS environment, and used to derive maps of forage production, guanacos density, soil organic carbon and soil erosion. Different scenarios, with different objectives weights were evaluated. Results showed that under scenario 1, where livestock production is predicted to have the highest values, guanaco numbers decrease substantially as well as soil carbon sequestration, and soil erosion exhibit the highest values. On the other hand, when guanaco population is prioritized, livestock production has the lowest value. A compromise alternative resulted from a scenario where variables are assigned same weight; under this condition, high livestock production is predicted, while conservation of guanaco population is sustainable, carbon sequestration is maximized and soil erosion minimized.

Can spatial study of hydrological connectivity explain some behaviors of catchments?

NASA Astrophysics Data System (ADS)

Cantreul, Vincent

2015-04-01

Erosion is a major threat to European soil. Consequences can be very important both on-site and off-site. Belgian loamy soils are highly vulnerable to this threat because of their natural sensitivity to erosion on the one hand, and because the land is mainly used for intensive agricultural practices on the other hand. Over the last few decades, rising erosion has even been observed in our regions. This shows the importance of a deeper understanding of the coupled phenomena of runoff and erosion in order to manage soils at catchment scale. Plenty of research have already studied this but all agree to say that it seems to have a non-linear relationship between rainfall and discharge, as well as between rainfall and erosion. For that reason, a new concept has been developed a few years ago: the hydrological connectivity. Several research have focused on connectivity but up to now, each there are as much definition as papers. In this thesis, it will be important firstly to resume all these definitions to clarify this concept. Secondly, a methodology using various transects on the watershed and some pertinent field measurements will be used. These measurements include spatial distribution of particle size, surface states and soil moisture. A new approach of photogrammetry using an UAV will be used to observe erosion and deposition zones on the watershed. In this framework, several time scales will be studied from the event scale to the annual scale passing by monthly and seasonal scales. All this will serve to progress toward a better understanding of the concept of hydrological connectivity in order to study erosion at catchment scale. The final goal of this study is to describe hydrologically each different part of the catchment and to generalize these behaviors to other catchments with similar properties if possible. Afterwards, this research will be integrated in an existing (or not) model to improve the modelling of discharge and erosion in the catchment. Thanks to that, a scenario of hydraulic mitigation measures could be proposed in order to reduce runoff and erosion in the catchment. This scenario will include hydraulic, hydrologic but also ecological, landscape and economical points of view. Key words: catchment, erosion, runoff, modelling, connectivity, UAV, scale, mitigation measures

Fault tectonics and earthquake hazards in the Peninsular Ranges, Southern California. [including San Diego River, Otay Mts., Japatul Valley, Barrett Lake, Horsethief Canyon, Pine Valley Creek, Pine Creek, and Mojave Desert

NASA Technical Reports Server (NTRS)

Merifield, P. M. (Principal Investigator)

1975-01-01

The author has identified the following significant results. Thin sections of rock exposed along the San Diego River linear were prepared and determined to be fault breccia. Single band and ratio images of the western Mojave Desert were prepared from the multispectral scanner digital tapes. Subtle differences in color of soil and rock are enhanced on the ratio images. Two north-northeast trending linears (Horsethief Canyon and Pine Valley Creek) and an east-west linear (Pine Creek) were concluded to have resulted from erosion along well-developed foliation in crystalline basement rocks.

Quantification Of Erosion Rates Of Agriculturally Used Soils By Artificial

NASA Astrophysics Data System (ADS)

Jha, Abhinand

2010-05-01

0.0.1 1. Introduction to soil erosion measurement by radionuclides Soil erosion by water, wind and tillage affects both agriculture and the natural environment. Studying this phenomenon would be one of the advancements in science. Soil erosion occurs worldwide and since the last two decades it has been a main topic of discussion all over the world. The use of environmental radionuclides such as 90Sr, 137Cs to study medium term soil erosion (40 yrs) started in the early 1990's. Using these new techniques better knowledge about erosion can be gained and this knowledge can be implemented for erosion risk management. The erosion and sedimentation study by using man-made and natural radioisotopes is a key technique, which has developed over the past 30 years. Fallout 137Cs and Cosmogenic 7Be are radionuclides that have been used to provide independent measurements of soil-erosion and sediment-deposition rates and patterns [1] [2] [3] [4]. Erosion measurements using radionuclides 137Cs, 7Be Caesium-137 from atmospheric nuclear-weapons tests in the 1950s and 1960s (Fig.1) is a unique tracer of erosion and sedimentation, since there are no natural sources of 137Cs. Unique events such as the Chernobyl accident in April 1986 caused regional dispersal of 137Cs that affects the total global deposition budget. This yearly pattern of fallout can be used to develop a chronology of deposition horizons in lakes, reservoirs, and floodplains. 137Cs can be easily measured by gamma spectroscopy. Using 137Cs is a fast and cheap method to study erosion-deposition processes compared to the traditional methods like silt bags. PIC Figure 1: Global 137Cs fallout (Modified from SAAS Bulletin 353, Part E, DDR, 1986) When 137Cs, 7Be reach the soil surface by wet and dry deposition, they are quickly and strongly adsorbed by ion exchange and are essentially non exchangeable in most environments. Each radionuclide is distributed differently in the soil because of differences in half-lives (30 yrs for 137Cs and 53 days for 7Be), delivery rates, delivery histories, and land use (Fig. 2). An Physical processes, such as water and wind, are the dominant factors moving 137Cs, 7Be tagged soil particles within and between landscape compartments. PIC Figure 2: Generalized sketch illustrating the distributions of 137Cs and 7Be in tilled and undisturbed soils 2 Erosion study at Young Moraine regions of Germany Recently, a study had been performed to evaluate erosion rates in a typical pattern of landscapes in the Young Moraine regions of North-East Germany [5]. The 137Cs concentrations were measured at selected sampling points of various study sites. Among the areas selected for sampling was Basedow, which is a cultivated area, situated north of Berlin. During a master thesis study at university of Bremen in the academic year 2008-2009 [6] a second sampling campaign was performed at the same study site and 137Cs and 7Be concentrations were measured. Two mathematical models (a proportional model and a mass balance model) were applied to estimate erosion or deposition rates giving a distinction between uncultivated or essentially undisturbed soils and cultivated or soils under permanent pasture (Fig.3A). An improved depositional model was developed during this study. The simulation results from this model are presented in Fig.4. Due to the half-life (53.2 days) of 7Be, a mass balance model was developed and used to calculate erosion rates from 7Be (Fig.3B). PIC Figure 3: A: Erosion rates for 137Cs calculated by mass balance model. B: Erosion rates calculated with mass balance model using the 7Be data at Basedow (2008). The results verify that there is long term erosion as a result of wind, water and agricultural practices. The annual erosion rates at Basedow calculated using a mass balance and a proportional model were in the range between 30-50 t ha-1yr-1. These values were comparable to the erosion rates calculated in the previous study [5] by the models mentioned above. PIC Figure 4: Profiles of sediment calculated for different erosion rates by Cs-137 within the ploughed soil 3 Conclusions and outlook Erosion rates for agricultural soils at Young Moraine regions of North-East Germany were determined by using two radionuclides, 137Cs and 7Be. In combination, the two radionuclides provide a valuable means of investigating soil erosion and assessing erosion risk in the study area. Potentials and limitations of the erosion measurement techniques using radiotracers are discussed in this study. The models used to quantify erosion rates using 137Cs and 7Be were studied. Erosion rates calculated by theses models are difficult to measure over a period of 50 years. A validation of these erosion rates for the time period (50 years) used in the 137Cs-based models will give a new perspective to the use of soil erosion modeling. Most of the regions in India are suffering from high erosion rates [7]. By using the new techniques in erosion quantification the land management practices can be improved and the erosion risk can be reduced in India.

7 CFR 613.2 - Policy and objectives.

Code of Federal Regulations, 2011 CFR

2011-01-01

... working with experiment stations, crop improvement associations, and other State and Federal agencies. (b... related to: (1) Controlling soil erosion on all lands; (2) Conserving water; (3) Protecting upstream... enhancement; (12) Selecting plants that tolerate air pollution agents and toxic soil chemicals; (13) Selecting...

Trend of Soil Erosion Processes within the Southern Half of the Russian Plain for the Last Decades

NASA Astrophysics Data System (ADS)

Golosov, V. N.; Yermolaev, O. P.; Safina, G. R.; Maltsev, K. A.; Gusarov, A. V.; Rysin, I. I.

2018-01-01

Complex approach is applied for assessment of recent trends of sheet, rill and gully erosion in different landscape zones of study area. Investigation is undertaken in 6 selected sectors (area of each transect is about 6-10 thousand km2), uniformly distributed over the area of the Russian Plain. Changes of the different factors, including some meteorological and hydrological parameters, land use change, USLE C-factor, were determined for the period 1980-2015. A set of field methods was used for quantification of sediment redistribution rates for the key small catchments. It was found that erosion rate decreased in forest and forest-steppe zone. Gully density decreases considerably in all landscape zones. The reduction of surface runoff from cultivated slope during snow-melting is the main reason of decreasing of sheet, rill and gully erosion rates in the forest, forest steppe and the north of steppe landscape zones. Increasing the proportion of perennial grasses in crop-rotation is the other factor of serious reduction of erosion processes in the forest zone.

Scaling up from field to region for wind erosion prediction using a field-scale wind erosion model and GIS

USGS Publications Warehouse

Zobeck, T.M.; Parker, N.C.; Haskell, S.; Guoding, K.

2000-01-01

Factors that affect wind erosion such as surface vegetative and other cover, soil properties and surface roughness usually change spatially and temporally at the field-scale to produce important field-scale variations in wind erosion. Accurate estimation of wind erosion when scaling up from fields to regions, while maintaining meaningful field-scale process details, remains a challenge. The objectives of this study were to evaluate the feasibility of using a field-scale wind erosion model with a geographic information system (GIS) to scale up to regional levels and to quantify the differences in wind erosion estimates produced by different scales of soil mapping used as a data layer in the model. A GIS was used in combination with the revised wind erosion equation (RWEQ), a field-scale wind erosion model, to estimate wind erosion for two 50 km2 areas. Landsat Thematic Mapper satellite imagery from 1993 with 30 m resolution was used as a base map. The GIS database layers included land use, soils, and other features such as roads. The major land use was agricultural fields. Data on 1993 crop management for selected fields of each crop type were collected from local government agency offices and used to 'train' the computer to classify land areas by crop and type of irrigation (agroecosystem) using commercially available software. The land area of the agricultural land uses was overestimated by 6.5% in one region (Lubbock County, TX, USA) and underestimated by about 21% in an adjacent region (Terry County, TX, USA). The total estimated wind erosion potential for Terry County was about four times that estimated for adjacent Lubbock County. The difference in potential erosion among the counties was attributed to regional differences in surface soil texture. In a comparison of different soil map scales in Terry County, the generalised soil map had over 20% more of the land area and over 15% greater erosion potential in loamy sand soils than did the detailed soil map. As a result, the wind erosion potential determined using the generalised soil map Was about 26% greater than the erosion potential estimated by using the detailed soil map in Terry County. This study demonstrates the feasibility of scaling up from fields to regions to estimate wind erosion potential by coupling a field-scale wind erosion model with GIS and identifies possible sources of error with this approach.

Nourishment of perched sand dunes and the issue of erosion control in the Great Lakes

NASA Astrophysics Data System (ADS)

Marsh, William M.

1990-09-01

Although limited in coverage, perched sand dunes situated on high coastal bluffs are considered the most prized of Great Lakes dunes. Grand Sable Dunes on Lake Superior and Sleeping Bear Dunes on Lake Michigan are featured attractions of national lakeshores under National Park Service management. The source of sand for perched dunes is the high bluff along their lakeward edge. As onshore wind crosses the bluff, flow is accelerated upslope, resulting in greatly elevated levels of wind stress over the slope brow. On barren, sandy bluffs, wind erosion is concentrated in the brow zone, and for the Grand Sable Bluff, it averaged 1 m3/yr per linear meter along the highest sections for the period 1973 1983. This mechanism accounts for about 6,500 m3 of sand nourishment to the dunefield annually and clearly has been the predominant mechanism for the long-term development of the dunefield. However, wind erosion and dune nourishment are possible only where the bluff is denuded of plant cover by mass movements and related processes induced by wave erosion. In the Great Lakes, wave erosion and bluff retreat vary with lake levels; the nourishment of perched dunes is favored by high levels. Lake levels have been relatively high for the past 50 years, and shore erosion has become a major environmental issue leading property owners and politicians to support lake-level regulation. Trimming high water levels could reduce geomorphic activity on high bluffs and affect dune nourishment rates. Locally, nourishment also may be influenced by sediment accumulation associated with harbor protection facilities and by planting programs aimed at stabilizing dunes.

Surface-Sensitive Microwear Texture Analysis of Attrition and Erosion.

PubMed

Ranjitkar, S; Turan, A; Mann, C; Gully, G A; Marsman, M; Edwards, S; Kaidonis, J A; Hall, C; Lekkas, D; Wetselaar, P; Brook, A H; Lobbezoo, F; Townsend, G C

2017-03-01

Scale-sensitive fractal analysis of high-resolution 3-dimensional surface reconstructions of wear patterns has advanced our knowledge in evolutionary biology, and has opened up opportunities for translatory applications in clinical practice. To elucidate the microwear characteristics of attrition and erosion in worn natural teeth, we scanned 50 extracted human teeth using a confocal profiler at a high optical resolution (X-Y, 0.17 µm; Z < 3 nm). Our hypothesis was that microwear complexity would be greater in erosion and that anisotropy would be greater in attrition. The teeth were divided into 4 groups, including 2 wear types (attrition and erosion) and 2 locations (anterior and posterior teeth; n = 12 for each anterior group, n = 13 for each posterior group) for 2 tissue types (enamel and dentine). The raw 3-dimensional data cloud was subjected to a newly developed rigorous standardization technique to reduce interscanner variability as well as to filter anomalous scanning data. Linear mixed effects (regression) analyses conducted separately for the dependent variables, complexity and anisotropy, showed the following effects of the independent variables: significant interactions between wear type and tissue type ( P = 0.0157 and P = 0.0003, respectively) and significant effects of location ( P < 0.0001 and P = 0.0035, respectively). There were significant associations between complexity and anisotropy when the dependent variable was either complexity ( P = 0.0003) or anisotropy ( P = 0.0014). Our findings of greater complexity in erosion and greater anisotropy in attrition confirm our hypothesis. The greatest geometric means were noted in dentine erosion for complexity and dentine attrition for anisotropy. Dentine also exhibited microwear characteristics that were more consistent with wear types than enamel. Overall, our findings could complement macrowear assessment in dental clinical practice and research and could assist in the early detection and management of pathologic tooth wear.

Advances in soil erosion modelling through remote sensing data availability at European scale

NASA Astrophysics Data System (ADS)

Panagos, Panos; Karydas, Christos; Borrelli, Pasqualle; Ballabio, Cristiano; Meusburger, Katrin

2014-08-01

Under the European Union's Thematic Strategy for Soil Protection, the European Commission's Directorate-General for the Environment (DG Environment) has identified the mitigation of soil losses by erosion as a priority area. Policy makers call for an overall assessment of soil erosion in their geographical area of interest. They have asked that risk areas for soil erosion be mapped under present land use and climate conditions, and that appropriate measures be taken to control erosion within the legal and social context of natural resource management. Remote sensing data help to better assessment of factors that control erosion, such as vegetation coverage, slope length and slope angle. In this context, the data availability of remote sensing data during the past decade facilitates the more precise estimation of soil erosion risk. Following the principles of the Universal Soil Loss Equation (USLE), various options to calculate vegetative cover management (C-factor) have been investigated. The use of the CORINE Land Cover dataset in combination with lookup table values taken from the literature is presented as an option that has the advantage of a coherent input dataset but with the drawback of static input. Recent developments in the Copernicus programme have made detailed datasets available on land cover, leaf area index and base soil characteristics. These dynamic datasets allow for seasonal estimates of vegetation coverage, and their application in the G2 soil erosion model which represents a recent approach to the seasonal monitoring of soil erosion. The use of phenological datasets and the LUCAS land use/cover survey are proposed as auxiliary information in the selection of the best methodology.

Root characteristics of cover crops and their erosion-reducing potential during concentrated runoff

NASA Astrophysics Data System (ADS)

de Baets, S.; Poesen, J.

2009-04-01

In the loam region in central Belgium, a lot of research has been conducted on the effects of cover crops for preventing splash and interrill erosion and on their nutrient pumping effectiveness. As this is a very effective erosion and environment conservation technique, planting cover crops during the winter season is widely applied in the loess belt. Most of these cover crops freeze at the beginning of the winter period. Consequently, the above-ground biomass becomes less effective in protecting the soil from water erosion. Apart from the effects of the above-ground biomass in protecting the soil against raindrop impacts and reducing flow velocities by the retarding effects of their stems, plant roots also play an important role in improving soil strength. Previous research showed that roots contribute to a large extent to the resistance of topsoils against concentrated flow erosion. Unfortunately, information on root properties of common cover crops (e.g. Sinapis alba, Phacelia tanacetifoli, Lolium perenne, Avena sativa, Secale cereale, Raphanus sativus subsp. oleiferus) is very scarce. Therefore, root density distribution with depth and their erosion-reducing effects during concentrated flow erosion were assessed by conducting root auger measurements and concentrated flow experiments at the end of the growth period (December). The preliminary results indicate that the studied cover crops are not equally effective in preventing soil loss by concentrated flow erosion at the end of the growing season. Cover crops with thick roots, such as Sinapis alba and Raphanus sativus subsp. oleiferus are less effective than cover crops with fine-branched roots such as Phacelia tanacetifoli, Lolium perenne (Ryegrass), Avena sativa (Oats) and Secale cereale (Rye) in preventing soil losses by concentrated flow erosion. These results enable soil managers to select the most suitable crops and maximize soil protection.

Quantifying and modeling soil erosion and sediment export from construction sites in southern California

NASA Astrophysics Data System (ADS)

Wernet, A. K.; Beighley, R. E.

2006-12-01

Soil erosion is a power process that continuously alters the Earth's landscape. Human activities, such as construction and agricultural practices, and natural events, such as forest fires and landslides, disturb the landscape and intensify erosion processes leading to sudden increases in runoff sediment concentrations and degraded stream water quality. Understanding soil erosion and sediment transport processes is of great importance to researchers and practicing engineers, who routinely use models to predict soil erosion and sediment movement for varied land use and climate change scenarios. However, existing erosion models are limited in their applicability to constructions sites which have highly variable soil conditions (density, moisture, surface roughness, and best management practices) that change often in both space and time. The goal of this research is to improve the understanding, predictive capabilities and integration of treatment methodologies for controlling soil erosion and sediment export from construction sites. This research combines modeling with field monitoring and laboratory experiments to quantify: (a) spatial and temporal distribution of soil conditions on construction sites, (b) soil erosion due to event rainfall, and (c) potential offsite discharge of sediment with and without treatment practices. Field sites in southern California were selected to monitor the effects of common construction activities (ex., cut/fill, grading, foundations, roads) on soil conditions and sediment discharge. Laboratory experiments were performed in the Soil Erosion Research Laboratory (SERL), part of the Civil and Environmental Engineering department at San Diego State University, to quantify the impact of individual factors leading to sediment export. SERL experiments utilize a 3-m by 10-m tilting soil bed with soil depths up to 1 m, slopes ranging from 0 to 50 percent, and rainfall rates up to 150 mm/hr (6 in/hr). Preliminary modeling, field and laboratory results are presented.

A simple, sensitive and non-destructive technique for characterizing bovine dental enamel erosion: attenuated total reflection Fourier transform infrared spectroscopy

PubMed Central

Kim, In-Hye; Son, Jun Sik; Min, Bong Ki; Kim, Young Kyoung; Kim, Kyo-Han; Kwon, Tae-Yub

2016-01-01

Although many techniques are available to assess enamel erosion in vitro, a simple, non-destructive method with sufficient sensitivity for quantifying dental erosion is required. This study characterized the bovine dental enamel erosion induced by various acidic beverages in vitro using attenuated total reflection Fourier transform infrared (ATR-FTIR) spectroscopy. Deionized water (control) and 10 acidic beverages were selected to study erosion, and the pH and neutralizable acidity were measured. Bovine anterior teeth (110) were polished with up to 1 200-grit silicon carbide paper to produce flat enamel surfaces, which were then immersed in 20 mL of the beverages for 30 min at 37 °C. The degree of erosion was evaluated using ATR-FTIR spectroscopy and Vickers' microhardness measurements. The spectra obtained were interpreted in two ways that focused on the ν1, ν3 phosphate contour: the ratio of the height amplitude of ν3 PO4 to that of ν1 PO4 (Method 1) and the shift of the ν3 PO4 peak to a higher wavenumber (Method 2). The percentage changes in microhardness after the erosion treatments were primarily affected by the pH of the immersion media. Regression analyses revealed highly significant correlations between the surface hardness change and the degree of erosion, as detected by ATR-FTIR spectroscopy (P<0.001). Method 1 was the most sensitive to these changes, followed by surface hardness change measurements and Method 2. This study suggests that ATR-FTIR spectroscopy is potentially advantageous over the microhardness test as a simple, non-destructive, sensitive technique for the quantification of enamel erosion. PMID:27025266

A simple, sensitive and non-destructive technique for characterizing bovine dental enamel erosion: attenuated total reflection Fourier transform infrared spectroscopy.

PubMed

Kim, In-Hye; Son, Jun Sik; Min, Bong Ki; Kim, Young Kyoung; Kim, Kyo-Han; Kwon, Tae-Yub

2016-03-30

Although many techniques are available to assess enamel erosion in vitro, a simple, non-destructive method with sufficient sensitivity for quantifying dental erosion is required. This study characterized the bovine dental enamel erosion induced by various acidic beverages in vitro using attenuated total reflection Fourier transform infrared (ATR-FTIR) spectroscopy. Deionized water (control) and 10 acidic beverages were selected to study erosion, and the pH and neutralizable acidity were measured. Bovine anterior teeth (110) were polished with up to 1 200-grit silicon carbide paper to produce flat enamel surfaces, which were then immersed in 20 mL of the beverages for 30 min at 37 °C. The degree of erosion was evaluated using ATR-FTIR spectroscopy and Vickers' microhardness measurements. The spectra obtained were interpreted in two ways that focused on the ν1, ν3 phosphate contour: the ratio of the height amplitude of ν3 PO4 to that of ν1 PO4 (Method 1) and the shift of the ν3 PO4 peak to a higher wavenumber (Method 2). The percentage changes in microhardness after the erosion treatments were primarily affected by the pH of the immersion media. Regression analyses revealed highly significant correlations between the surface hardness change and the degree of erosion, as detected by ATR-FTIR spectroscopy (P<0.001). Method 1 was the most sensitive to these changes, followed by surface hardness change measurements and Method 2. This study suggests that ATR-FTIR spectroscopy is potentially advantageous over the microhardness test as a simple, non-destructive, sensitive technique for the quantification of enamel erosion.

Linear IgA dermatosis associated with ulcerative colitis: complete and sustained remission after total colectomy.

PubMed

Vargas, Thiago Jeunon de Sousa; Fialho, Mônica; Santos, Luiza Tavares dos; Rodrigues, Palmira Assis de Jesus Barreto; Vargas, Ana Luisa Bittencourt Sampaio Jeunon; Sousa, Maria Auxiliadora Jeunon

2013-01-01

Linear IgA dermatosis has been increasingly associated with inflammatory bowel diseases, particularly ulcerative colitis. A 13-year-old male patient with an 11-month history of ulcerative colitis developed vesicles, pustules and erosions on the skin of the face, trunk and buttocks and in the oral mucosa. The work-up revealed a neutrophil-rich sub-epidermal bullous disease and linear deposition of IgA along the dermoepidermal junction, establishing the diagnosis of linear IgA dermatosis. The patient experienced unsatisfactory partial control of skin and intestinal symptoms despite the use of adalimumab, mesalazine, prednisone and dapsone for some months. After total colectomy, he presented complete remission of skin lesions, with no need of medications during two years of follow-up. A review of previously reported cases of the association is provided here and the role of ulcerative colitis in triggering linear IgA dermatosis is discussed.

Development of a model to predict ash transport and water pollution risk in fire-affected environments

NASA Astrophysics Data System (ADS)

Neris, Jonay; Elliot, William J.; Doerr, Stefan H.; Robichaud, Peter R.

2017-04-01

An estimated that 15% of the world's population lives in volcanic areas. Recent catastrophic erosion events following wildfires in volcanic terrain have highlighted the geomorphological instability of this soil type under disturbed conditions and steep slopes. Predicting the hydrological and erosional response of this soils in the post-fire period is the first step to design and develop adequate actions to minimize risks in the post-fire period. In this work we apply, for the first time, the Water Erosion Prediction Project model for predicting erosion and runoff events in fire-affected volcanic soils in Europe. Two areas affected by wildfires in 2015 were selected in Tenerife (Spain) representative of different fire behaviour (downhill surface fire with long residence time vs uphill crown fire with short residence time), severity (moderate soil burn severity vs light soil burn severity) and climatic conditions (average annual precipitation of 750 and 210 mm respectively). The actual erosion processes were monitored in the field using silt fences. Rainfall and rill simulations were conducted to determine hydrologic, interrill and rill erosion parameters. The soils were sampled and key properties used as model input, evaluated. During the first 18 months after the fire 7 storms produced runoff and erosion in the selected areas. Sediment delivery reached 5.4 and 2.5 Mg ha-1 respectively in the first rainfall event monitored after the fire, figures comparable to those reported for fire-affected areas of the western USA with similar climatic conditions but lower than those showed by wetter environments. The validation of the WEPP model using field data showed reasonable estimates of hillslope sediment delivery in the post-fire period and, therefore, it is suggested that this model can support land managers in volcanic areas in Europe in predicting post-fire hydrological and erosional risks and designing suitable mitigation treatments.

A Quantitative Study of Gully Erosion Based on Object-Oriented Analysis Techniques: A Case Study in Beiyanzikou Catchment of Qixia, Shandong, China

PubMed Central

Wang, Tao; He, Fuhong; Zhang, Anding; Gu, Lijuan; Wen, Yangmao; Jiang, Weiguo; Shao, Hongbo

2014-01-01

This paper took a subregion in a small watershed gully system at Beiyanzikou catchment of Qixia, China, as a study and, using object-orientated image analysis (OBIA), extracted shoulder line of gullies from high spatial resolution digital orthophoto map (DOM) aerial photographs. Next, it proposed an accuracy assessment method based on the adjacent distance between the boundary classified by remote sensing and points measured by RTK-GPS along the shoulder line of gullies. Finally, the original surface was fitted using linear regression in accordance with the elevation of two extracted edges of experimental gullies, named Gully 1 and Gully 2, and the erosion volume was calculated. The results indicate that OBIA can effectively extract information of gullies; average range difference between points field measured along the edge of gullies and classified boundary is 0.3166 m, with variance of 0.2116 m. The erosion area and volume of two gullies are 2141.6250 m2, 5074.1790 m3 and 1316.1250 m2, 1591.5784 m3, respectively. The results of the study provide a new method for the quantitative study of small gully erosion. PMID:24616626

Impact of erosion and tillage on the productivity and quality of selected semiarid soils of Iran

NASA Astrophysics Data System (ADS)

Mehdizade, B.; Asadi, H.; Shabanpour, M.; Ghadiri, H.

2013-09-01

This greenhouse research was carried out to study the effects of water and tillage erosion on agricultural productivity and soil quality in soil samples from a semiarid region of Iran. A factorial experiment of complete randomized block design was used to compare the effects of soil erosion (eroded and non-eroded soils), slope position, water stress and fertilizer (N-P-K) on yield and yield components of wheat as soil productivity index. The results showed that erosion ie water and tillage erosion has a significant effect (p<0.01) in decreasing soil productivity due to its negative impact on soil organic matter, nutrients (N and K) and hydraulic conductivity. Complete N-P-K fertilization and water stress had significant effects on increasing and decreasing of wheat yield, respectively. The effect of water stress in particular was so high that it could eclipse the erosion impact on yield reduction. Wheat dry matter and grain mass on foot and mid slopes were significantly higher than that on upslope positions where total N and available K were the lowest and equivalent calcium carbonate the highest. Saturated hydraulic conductivity and total nitrogen were found to be the most important soil properties as far as their correlations to wheat yield are concerned.

Use of (137)Cs technique for soil erosion study in the agricultural region of Casablanca in Morocco.

PubMed

Nouira, A; Sayouty, E H; Benmansour, M

2003-01-01

Accelerated erosion and soil degradation currently cause serious problems to the Oued El Maleh basin (Morocco). Furthermore, there is still only limited information on rates of soil loss for optimising strategies for soil conservation. In the present study we have used the (137)Cs technique to assess the soil erosion rates on an agricultural land in Oued el Maleh basin near Casablanca (Morocco). A small representative agricultural field was selected to investigate the soil degradation required by soil managers in this region. The transect approach was applied for sampling to identify the spatial redistribution of (137)Cs. The spatial variability of (137)Cs inventory has provided evidence of the importance of tillage process and the human effects on the redistribution of (137)Cs. The mean (137)Cs inventory was found about 842 Bq m(-2), this value corresponds to an erosion rate of 82 tha(-1) yr(-1) by applying simplified mass balance model in a preliminary estimation. When data on site characteristics were available, the refined mass balance model was applied to highlight the contribution of tillage effect in soil redistribution. The erosion rate was estimated about 50 tha(-1) yr(-1). The aspects related to the sampling procedures and the models for calculation of erosion rates are discussed.

Bedrock river erosion measurements and modelling along a river of the Frontal Himalaya

NASA Astrophysics Data System (ADS)

Lave, Jerome; Dubille, Matthieu

2017-04-01

River incision is a key process in mountains denudation and therefore in landscape evolution models. Despite its importance, most incision models for mountain rivers rely on simplified, or quite empirical relations, and generally only consider annual average values for water discharge and sediment flux. In contrast, very few studies consider mechanistic models at the timescale of a flood, and try to bridge the gap between experimental or theoretical approaches and long term river incision studies. In this contribution, we present observations made during 7 monsoon seasons on fluvial bedrock erosion along the Bakeya river across the Frontal Himalaya in Central Nepal. Along its lower gorge, this river incises alternation of indurated sandstone and less resistant claystone, at Holocene rates larger than 10mm/yr. More importantly, its upper drainage mostly drains through non-cohesive conglomerate which allows, in this specific setting, estimating the bedload characteristics and instantaneous fluxes, i.e. a pre-requisite to test mechanistic models of fluvial erosion. During the study period, we monitored and documented the channel bank erosion in order to understand the amplitude of the erosion processes, their occurrence in relation with hydrology, in order to test time-integrated models of erosion. Besides hydrologic monitoring, erosion measurements were threefold: (1) at the scale of the whole monsoon, plucking and block removal by repeated photo surveys of a 400m long channel reach, (2) detailed microtopographic surveys of channel bedrock elevation along a few sandstone bars to document their abrasion, (3) real time measurement of fluvial bedrock wear to document erosion timing using a new erosion sensor. Results indicate that: 1. Erosion is highly dependent on rock resistance, but on average block detachment and removal is a more efficient process than bedrock attrition, and operates at a rate that permit channel banks downcutting to keep pace with Holocene uplift rate. 2. Both block detachment and attrition processes clearly increase with fluvial shear stress, but non-linearly, in particular through the existence of a minimum threshold. As a result of which bank erosion occur during only a few hours per year during short and very high flood events, which questions the use of average discharge (or drainage area) in many bedrock erosion models. We then propose a semi-physical model of sandstone bars abrasion based on discharge history (HEC-RAS modelling), Rouse suspension model, and experimental measurements on dependency of abrasion rate vs impacting particle size. This model predicts well the timing and the amplitude of both real-time and monsoon average abrasion along the surveyed sandstone bars. This first validation of a model for bank erosion opens large perspective for future work on channel bottom incision modelling using physical models of erosion and their time- and gravel-size-integration, with the objective to introduce more physical rules in landscape evolution models.

Wind-Driven Erosion and Exposure Potential at Mars 2020 Rover Candidate-Landing Sites.

PubMed

Chojnacki, Matthew; Banks, Maria; Urso, Anna

2018-02-01

Aeolian processes have likely been the predominant geomorphic agent for most of Mars' history and have the potential to produce relatively young exposure ages for geologic units. Thus, identifying local evidence for aeolian erosion is highly relevant to the selection of landing sites for future missions, such as the Mars 2020 Rover mission that aims to explore astrobiologically relevant ancient environments. Here we investigate wind-driven activity at eight Mars 2020 candidate-landing sites to constrain erosion potential at these locations. To demonstrate our methods, we found that contemporary dune-derived abrasion rates were in agreement with rover-derived exhumation rates at Gale crater and could be employed elsewhere. The Holden crater candidate site was interpreted to have low contemporary erosion rates, based on the presence of a thick sand coverage of static ripples. Active ripples at the Eberswalde and southwest Melas sites may account for local erosion and the dearth of small craters. Moderate-flux regional dunes near Mawrth Vallis were deemed unrepresentative of the candidate site, which is interpreted to currently be experiencing low levels of erosion. The Nili Fossae site displayed the most unambiguous evidence for local sand transport and erosion, likely yielding relatively young exposure ages. The downselected Jezero crater and northeast Syrtis sites had high-flux neighboring dunes and exhibited substantial evidence for sediment pathways across their ellipses. Both sites had relatively high estimated abrasion rates, which would yield young exposure ages. The downselected Columbia Hills site lacked evidence for sand movement, and contemporary local erosion rates are estimated to be relatively low.

The Dust Storm Index (DSI): A method for monitoring broadscale wind erosion using meteorological records

NASA Astrophysics Data System (ADS)

O'Loingsigh, T.; McTainsh, G. H.; Tews, E. K.; Strong, C. L.; Leys, J. F.; Shinkfield, P.; Tapper, N. J.

2014-03-01

Wind erosion of soils is a natural process that has shaped the semi-arid and arid landscapes for millennia. This paper describes the Dust Storm Index (DSI); a methodology for monitoring wind erosion using Australian Bureau of Meteorology (ABM) meteorological observational data since the mid-1960s (long-term), at continental scale. While the 46 year length of the DSI record is its greatest strength from a wind erosion monitoring perspective, there are a number of technical challenges to its use because when the World Meteorological Organisation (WMO) recording protocols were established the use of the data for wind erosion monitoring was never intended. Data recording and storage protocols are examined, including the effects of changes to the definition of how observers should interpret and record dust events. A method is described for selecting the 180 long-term ABM stations used in this study and the limitations of variable observation frequencies between stations are in part resolved. The rationale behind the DSI equation is explained and the examples of temporal and spatial data visualisation products presented include; a long term national wind erosion record (1965-2011), continental DSI maps, and maps of the erosion event types that are factored into the DSI equation. The DSI is tested against dust concentration data and found to provide an accurate representation of wind erosion activity. As the ABM observational records used here were collected according to WMO protocols, the DSI methodology could be used in all countries with WMO-compatible meteorological observation and recording systems.

Wind-Driven Erosion and Exposure Potential at Mars 2020 Rover Candidate-Landing Sites

PubMed Central

Chojnacki, Matthew; Banks, Maria; Urso, Anna

2018-01-01

Aeolian processes have likely been the predominant geomorphic agent for most of Mars’ history and have the potential to produce relatively young exposure ages for geologic units. Thus, identifying local evidence for aeolian erosion is highly relevant to the selection of landing sites for future missions, such as the Mars 2020 Rover mission that aims to explore astrobiologically relevant ancient environments. Here we investigate wind-driven activity at eight Mars 2020 candidate-landing sites to constrain erosion potential at these locations. To demonstrate our methods, we found that contemporary dune-derived abrasion rates were in agreement with rover-derived exhumation rates at Gale crater and could be employed elsewhere. The Holden crater candidate site was interpreted to have low contemporary erosion rates, based on the presence of a thick sand coverage of static ripples. Active ripples at the Eberswalde and southwest Melas sites may account for local erosion and the dearth of small craters. Moderate-flux regional dunes near Mawrth Vallis were deemed unrepresentative of the candidate site, which is interpreted to currently be experiencing low levels of erosion. The Nili Fossae site displayed the most unambiguous evidence for local sand transport and erosion, likely yielding relatively young exposure ages. The downselected Jezero crater and northeast Syrtis sites had high-flux neighboring dunes and exhibited substantial evidence for sediment pathways across their ellipses. Both sites had relatively high estimated abrasion rates, which would yield young exposure ages. The downselected Columbia Hills site lacked evidence for sand movement, and contemporary local erosion rates are estimated to be relatively low. PMID:29568719

Wind-Driven Erosion and Exposure Potential at Mars 2020 Rover Candidate-Landing Sites

NASA Astrophysics Data System (ADS)

Chojnacki, Matthew; Banks, Maria; Urso, Anna

2018-02-01

Aeolian processes have likely been the predominant geomorphic agent for most of Mars' history and have the potential to produce relatively young exposure ages for geologic units. Thus, identifying local evidence for aeolian erosion is highly relevant to the selection of landing sites for future missions, such as the Mars 2020 Rover mission that aims to explore astrobiologically relevant ancient environments. Here we investigate wind-driven activity at eight Mars 2020 candidate-landing sites to constrain erosion potential at these locations. To demonstrate our methods, we found that contemporary dune-derived abrasion rates were in agreement with rover-derived exhumation rates at Gale crater and could be employed elsewhere. The Holden crater candidate site was interpreted to have low contemporary erosion rates, based on the presence of a thick sand coverage of static ripples. Active ripples at the Eberswalde and southwest Melas sites may account for local erosion and the dearth of small craters. Moderate-flux regional dunes near Mawrth Vallis were deemed unrepresentative of the candidate site, which is interpreted to currently be experiencing low levels of erosion. The Nili Fossae site displayed the most unambiguous evidence for local sand transport and erosion, likely yielding relatively young exposure ages. The downselected Jezero crater and northeast Syrtis sites had high-flux neighboring dunes and exhibited substantial evidence for sediment pathways across their ellipses. Both sites had relatively high estimated abrasion rates, which would yield young exposure ages. The downselected Columbia Hills site lacked evidence for sand movement, and contemporary local erosion rates are estimated to be relatively low.

Identification of critical sediment source areas at regional level

NASA Astrophysics Data System (ADS)

Fargas, D.; Casasnovas, J. A. Martínez; Poch, R.

In order to identify critical sediment sources in large catchments, using easily available terrain information at regional scale, a methodology has been developed to obtain a qualitative assessment necessary for further studies. The main objective of the model is to use basic terrain data related to the erosive processes which contribute to the production, transport and accumulation of sediments through the main water paths in the watershed. The model is based on the selection of homogeneous zones regarding drainage density and lithology, achieved by joining the spatial basic units by a rating system. The values of drainage density are rated according to an erosion class (Bucko & Mazurova, 1958). The lithology is rated by erosion indexes, adapted from FAO (1977). The combination and reclassification of the results brings about five qualitative classes of sediment emission risk. This methodology has been tested an validated for the watershed of the Joaquín Costa reservoir (NE Spain), with a surface of 1500 km 2. The mapping scale was 1:100.000 and the model was implemented through a vector GIS (Arc/Info). The prediction was checked by means of photo-interpretation and field work, which gave a accuracy of 78.5%. The proposed methodology has been proved useful as an initial approach for erosion assessment and soil conservation planning at the regional level, and also to select priority areas where further analyses can be developed.

Modification of the USLE K factor for soil erodibility assessment on calcareous soils in Iran

NASA Astrophysics Data System (ADS)

Ostovari, Yaser; Ghorbani-Dashtaki, Shoja; Bahrami, Hossein-Ali; Naderi, Mehdi; Dematte, Jose Alexandre M.; Kerry, Ruth

2016-11-01

The measurement of soil erodibility (K) in the field is tedious, time-consuming and expensive; therefore, its prediction through pedotransfer functions (PTFs) could be far less costly and time-consuming. The aim of this study was to develop new PTFs to estimate the K factor using multiple linear regression, Mamdani fuzzy inference systems, and artificial neural networks. For this purpose, K was measured in 40 erosion plots with natural rainfall. Various soil properties including the soil particle size distribution, calcium carbonate equivalent, organic matter, permeability, and wet-aggregate stability were measured. The results showed that the mean measured K was 0.014 t h MJ- 1 mm- 1 and 2.08 times less than the estimated mean K (0.030 t h MJ- 1 mm- 1) using the USLE model. Permeability, wet-aggregate stability, very fine sand, and calcium carbonate were selected as independent variables by forward stepwise regression in order to assess the ability of multiple linear regression, Mamdani fuzzy inference systems and artificial neural networks to predict K. The calcium carbonate equivalent, which is not accounted for in the USLE model, had a significant impact on K in multiple linear regression due to its strong influence on the stability of aggregates and soil permeability. Statistical indices in validation and calibration datasets determined that the artificial neural networks method with the highest R2, lowest RMSE, and lowest ME was the best model for estimating the K factor. A strong correlation (R2 = 0.81, n = 40, p < 0.05) between the estimated K from multiple linear regression and measured K indicates that the use of calcium carbonate equivalent as a predictor variable gives a better estimation of K in areas with calcareous soils.

Decision support for the selection of reference sites using 137Cs as a soil erosion tracer

NASA Astrophysics Data System (ADS)

Arata, Laura; Meusburger, Katrin; Bürge, Alexandra; Zehringer, Markus; Ketterer, Michael E.; Mabit, Lionel; Alewell, Christine

2017-08-01

The classical approach of using 137Cs as a soil erosion tracer is based on the comparison between stable reference sites and sites affected by soil redistribution processes; it enables the derivation of soil erosion and deposition rates. The method is associated with potentially large sources of uncertainty with major parts of this uncertainty being associated with the selection of the reference sites. We propose a decision support tool to Check the Suitability of reference Sites (CheSS). Commonly, the variation among 137Cs inventories of spatial replicate reference samples is taken as the sole criterion to decide on the suitability of a reference inventory. Here we propose an extension of this procedure using a repeated sampling approach, in which the reference sites are resampled after a certain time period. Suitable reference sites are expected to present no significant temporal variation in their decay-corrected 137Cs depth profiles. Possible causes of variation are assessed by a decision tree. More specifically, the decision tree tests for (i) uncertainty connected to small-scale variability in 137Cs due to its heterogeneous initial fallout (such as in areas affected by the Chernobyl fallout), (ii) signs of erosion or deposition processes and (iii) artefacts due to the collection, preparation and measurement of the samples; (iv) finally, if none of the above can be assigned, this variation might be attributed to turbation processes (e.g. bioturbation, cryoturbation and mechanical turbation, such as avalanches or rockfalls). CheSS was exemplarily applied in one Swiss alpine valley where the apparent temporal variability called into question the suitability of the selected reference sites. In general we suggest the application of CheSS as a first step towards a comprehensible approach to test for the suitability of reference sites.

Application of ERTS-1 data to the protection and management of New Jersey's coastal environment

NASA Technical Reports Server (NTRS)

Yunghans, R. S.; Feinberg, E. B.; Wobber, F. J.; Mairs, R. L. (Principal Investigator); Macomber, R. T.; Stanczuk, D.

1973-01-01

The author has identified the following significant results. Rates of erosion and accretion of the shoreline are being calculated for two test areas along the New Jersey coast. Measurements are made on aerial photographs taken over the last 20 years and processed by computer. The rates are presented in graphic form on an ERTS-1 base map at a scale of 1:125,000. These rates are being used to determine the effectiveness of various shore protection structures at preventing sand removal and encouraging sand accumulation. Information on maintenance and construction expenditures is being used to obtain a cost effectiveness ratio for various shore protection devices. The relationship of erosion rates, property value, and project cost are all criteria for selection of site type and extent of a shore protection structure. Compilation and evaluation of historical data will identify past decision making patterns. The effectiveness of these decisions with respect to erosion rates, property value, and project cost, can be used as an added criteria for future allocation of money and the selection of site and type of structure to be built.

Growth and erosion of mountain ranges at the northeastern margin of Tibet

NASA Astrophysics Data System (ADS)

Hetzel, Ralf; Palumbo, Luigi; Giese, Jörg; Guo, Jianming

2010-05-01

The hypothesis that mountain belts may reach a steady state, in which rock uplift is balanced by erosion, has been supported by numerous field studies and numerical models. The early evolution of mountain ranges, however, and especially the relation between fault growth and topographic response has received little attention. By using a space-for-time substitution we illustrate how active thrust faults and small, fault-bounded mountain ranges evolve into mature mountain chains that will ultimately be incorporated into the laterally growing Tibetan Plateau. At an early stage of development, when faults propagate laterally, slip rates are constant along strike [1-3]. As long as no significant topographic relief has developed, tectonic uplift is at least an order of magnitude faster than the rate of erosion [2,4]. During progressive relief growth and the establishment of drainage basins, erosion of the rising mountain ranges becomes more important, but the studied ranges are still in a pre-steady state and continue to grow both vertically and laterally [5]. During this stage the rate of erosion is linearly correlated to the mean hillslope gradient and the mean local relief, if differences in lithology or rock strength are negligible [6]. The rate of relief growth may be inferred from the difference between local erosion rates on ridge crests and catchment-wide denudation rates [7] - the latter may be taken as a surrogate for the rate of river incision. As hillslopes approach a threshold value, landsliding becomes the dominant process of mass transport and erosion rates increase non-linearly with slope. Once a steady state has been reached, the erosion rate is equal to the rate of rock uplift. A key problem is how the rate of rock uplift can be quantified in such regions, because the stochastic distribution of landslides causes the denudation rates inferred from 10Be in river sediment to be highly variable [8]. References [1] Hetzel et al. (2004). Implications of the fault scaling law for the growth of topography: Mountain ranges in the broken foreland of NE Tibet. Terra Nova 16, 157-162. [2] Hetzel et al. (2002). Low slip rates and long-term preservation of geomorphic features in Central Asia. Nature 417, 428-432. [3] Hetzel et al. (2004). Late Pleistocene/Holocene slip rate of the Zhangye thrust (Qilian Shan, China) and implications for the active growth of the northeastern Tibetan Plateau, Tectonics 23, TC6006, doi:10.1029/2004TC001653. [4] Goethals et al. (2009). Determining the impact of faulting on the rate of erosion in a low-relief landscape: A case study using in situ produced 21Ne on active normal faults in the Bishop Tuff, California. Geomorphology 103, 401-413. [5] Palumbo et al. (2009). Deciphering the rate of mountain growth during topographic presteady state: an example from the NE margin of the Tibetan Plateau. Tectonics 28, TC4017, doi:10.1029/2009TC002455. [6] Palumbo et al. (in press). Topographic and lithologic control on catchment-wide denudation rates derived from cosmogenic 10Be in two mountain ranges at the margin of NE Tibet. Geomorphology, doi:10.1016/j.geomorph.2009.11.019. [7] Meyer et al. (in press). Determining the growth rate of topographic relief using in situ-produced 10Be: A case study in the Black Forest, Germany. Earth and Planetary Science Letters. [8] Densmore et al. (2009). Spatial variations in catchment-averaged denudation rates from normal fault footwalls. Geology 37, 1139-1142.

Modelling the impact of vegetation on marly catchments in the Southern Alps of France

NASA Astrophysics Data System (ADS)

Carriere, Alexandra; Le Bouteiller, Caroline; Tucker, Greg; Naaim, Mohamed

2017-04-01

The Southern Alps of France have been identified as a hot-spot in a global climate change context where the rainfall intensity increase may exacerbate the erosion of already badly erodible lands: Badlands. Vegetalization methods are a promising area of research for erosion control and slope and riverbed stabilization. Nevertheless the impact of vegetation on erosive dynamics is still poorly understood. We own data collected over the last thirty years on marly catchments in the Southern Alps of France from the Draix-Bléone Observatory, part of the Network of Drainage Basins RBV. These are temporal data of sedimentary flux at the scale of the precipitation event but also more recent topographic data on watersheds with areas ranging from 10-3 square kilometers to twenty square kilometers. Erosion rates in this landscape reach 1 cm per year. We simulate the topographic evolution of the catchments over a few decades to centuries with the landscape evolution model Landlab, using our data to calibrate and explicitly validate the model. This model, in comparison with other landscape evolution models, incorporates a more advanced vegetation module in terms of ecology. Nevertheless the erosion-vegetation coupling is not present in Landlab and we are working on its construction. To this end we use an erosion module and a vegetation module that we seek to couple. We want to see how the erosion laws parameters depend on the vegetation cover. We have implemented the calibration of parameters of a non-linear diffusion module coupled with a transport-limited law by comparing the simulated annual sediment flux with the one of the data of the observatory as a function of the percentage of vegetation cover of the ground. We obtained average values of parameters adjusted according to vegetation cover. We observe that the values of the erosion laws parameters are strongly affected by the percentage of vegetation cover. We will then spatialize these parameters on our vegetation maps in order to obtain different parameter values for different types of vegetation.

Dental caries and erosion status of 12-year-old Hong Kong children

PubMed Central

2014-01-01

Background This study aimed to assess the dental caries and erosion status of 12-year-old Hong Kong children and study the determinants of dental caries and dental erosion of these children. Methods The survey was performed from 2011 to 2012 with ethics approval. Stratified random sampling was adopted to select 12-year-old children in 7 primary schools in Hong Kong. The participating parents were asked to complete a self-administered questionnaire concerning their children’s diet and oral health habits. The children were examined for caries status with WHO criteria by 3 calibrated examiners. Detection of dental erosion followed Basic Erosive Wear Examination (BEWE) criteria. Results A total of 704 children were recruited and 600 (316 boys, 53%) participated in the survey. There were 124 children (21%) with caries experience (DMFT > 0) and their DMFT was 0.34 ± 0.76. About half of their decay was unfilled (DT = 0.16 ± 0.52) The DMFT of girls and boys were 0.45 ± 0.89 and 0.23 ± 0.61, respectively (p = 0.001). Girls also had a higher DT (0.21 ± 0.62 compared with 0.11 ± 0.41, p = 0.013) and FT than boys (0.23 ± 0.63 compared with 0.12 ± 0.44, p = 0.016). Most children (75%) had at least some sign of erosion (BEWE > 0), but no severe erosion (BEWE = 3). Logistic regression showed girls who consumed soft drinks and took vitamin C supplements had higher caries risk. Dental erosion was more severe among the children who had caries experience and consumed fruit juice. Conclusions The 12-year-old Hong Kong children had low caries experience, and almost half of the decay was left untreated. Although severe erosion was not found, many children had early signs of erosion. PMID:24397565

Tooth erosion and eating disorders: a systematic review and meta-analysis.

PubMed

Hermont, Ana Paula; Oliveira, Patrícia A D; Martins, Carolina C; Paiva, Saul M; Pordeus, Isabela A; Auad, Sheyla M

2014-01-01

Eating disorders are associated with the highest rates of morbidity and mortality of any mental disorders among adolescents. The failure to recognize their early signs can compromise a patient's recovery and long-term prognosis. Tooth erosion has been reported as an oral manifestation that might help in the early detection of eating disorders. The aim of this systematic review and meta-analysis was to search for scientific evidence regarding the following clinical question: Do eating disorders increase the risk of tooth erosion? An electronic search addressing eating disorders and tooth erosion was conducted in eight databases. Two independent reviewers selected studies, abstracted information and assessed its quality. Data were abstracted for meta-analysis comparing tooth erosion in control patients (without eating disorders) vs. patients with eating disorders; and patients with eating disorder risk behavior vs. patients without such risk behavior. Combined odds ratios (ORs) and a 95% confidence interval (CI) were obtained. Twenty-three papers were included in the qualitative synthesis and assessed by a modified version of the Newcastle-Ottawa Scale. Fourteen papers were included in the meta-analysis. Patients with eating disorders had more risk of tooth erosion (OR = 12.4, 95%CI = 4.1-37.5). Patients with eating disorders who self-induced vomiting had more risk of tooth erosion than those patients who did not self-induce vomiting (OR = 19.6, 95%CI = 5.6-68.8). Patients with risk behavior of eating disorder had more risk of tooth erosion than patients without such risk behavior (Summary OR = 11.6, 95%CI = 3.2-41.7). The scientific evidence suggests a causal relationship between tooth erosion and eating disorders and purging practices. Nevertheless, there is a lack of scientific evidence to fulfill the basic criteria of causation between the risk behavior for eating disorders and tooth erosion.

A 4 year prospective longitudinal study of progression of dental erosion associated to lifestyle in 13-14 year-old Swedish adolescents.

PubMed

Hasselkvist, Agneta; Johansson, Anders; Johansson, Ann-Katrin

2016-04-01

To evaluate the progression of dental erosion in 13-14 year-olds after 4 years, and its association with lifestyle and oral health. 227 randomly selected 13-14 year-olds from a Public Dental Clinic, Örebro, Sweden, were investigated. A clinical examination was performed which included dental caries/gingival/plaque status, as well as grading of dental erosion at the tooth surface and participant levels in "marker teeth", including buccal/palatal surfaces of 6 maxillary anterior teeth (13-23), and occlusal surfaces of first molars. An interview and a questionnaire regarding drinking habits and other lifestyle factors were completed. All investigations were repeated at follow-up. The participants were divided into high and low progression erosion groups and logistic regression statistics were applied. 175 individuals participated at follow-up. Progression occurred in 35% of the 2566 tooth surfaces. 32% of the surfaces had deteriorated by one severity grade (n=51 individuals) and 3% by two grades (n=2 individuals). Boys showed more severe erosion than girls at the follow-up. Among the variables predicting greater progression, a lower severity of erosive wear at baseline had the highest OR (13.3), followed in descending order by a "retaining" drinking technique, more frequent intake of drinks between meals, low GBI and lesser sour milk intake, with reference to the baseline recording. Using these five variables, sensitivity and specificity were 87% and 67% respectively, for predicting progression of erosion. Progression of erosive lesions in Swedish adolescents aged 13-14 years followed up to age 17-18 years was common and related to certain lifestyle factors. In permanent teeth, dental erosion may develop early in life and its progression is common. Dental health workers should be made aware of this fact and regular screenings for erosion and recording of associated lifestyle factors should be performed. Copyright © 2016 Z. Published by Elsevier Ltd.. All rights reserved.

Estimating soil erosion risk and evaluating erosion control measures for soil conservation planning at Koga watershed in the highlands of Ethiopia

NASA Astrophysics Data System (ADS)

Molla, Tegegne; Sisheber, Biniam

2017-01-01

Soil erosion is one of the major factors affecting sustainability of agricultural production in Ethiopia. The objective of this paper is to estimate soil erosion using the universal soil loss equation (RUSLE) model and to evaluate soil conservation practices in a data-scarce watershed region. For this purpose, soil data, rainfall, erosion control practices, satellite images and topographic maps were collected to determine the RUSLE factors. In addition, measurements of randomly selected soil and water conservation structures were done at three sub-watersheds (Asanat, Debreyakob and Rim). This study was conducted in Koga watershed at upper part of the Blue Nile basin which is affected by high soil erosion rates. The area is characterized by undulating topography caused by intensive agricultural practices with poor soil conservation practices. The soil loss rates were determined and conservation strategies have been evaluated under different slope classes and land uses. The results showed that the watershed is affected by high soil erosion rates (on average 42 t ha-1 yr-1), greater than the maximum tolerable soil loss (18 t ha-1 yr-1). The highest soil loss (456 t ha-1 yr-1) estimated from the upper watershed occurred on cultivated lands of steep slopes. As a result, soil erosion is mainly aggravated by land-use conflicts and topographic factors and the rugged topographic land forms of the area. The study also demonstrated that the contribution of existing soil conservation structures to erosion control is very small due to incorrect design and poor management. About 35 % out of the existing structures can reduce soil loss significantly since they were constructed correctly. Most of the existing structures were demolished due to the sediment overload, vulnerability to livestock damage and intense rainfall. Therefore, appropriate and standardized soil and water conservation measures for different erosion-prone land uses and land forms need to be implemented in Koga watershed.

Sustainable agriculture, soil management and erosion from prehistoric times to 2100

NASA Astrophysics Data System (ADS)

Vanwalleghem, Tom; Gómez, Jose Alfonso; Infante Amate, Juan; González Molina, Manuel; Fernández, David Soto; Guzmán, Gema; Vanderlinden, Karl; Laguna, Ana; Giráldez, Juan Vicente

2015-04-01

The rational use of soil requires the selection of management practices to take profit of the beneficial functions of plant growth, water and nutrient storage, and pollutants removal by filtering and decomposition without altering its properties. However, the first evidence of important and widespread erosion peaks can generally be found with the arrival of the first farmers all over the world. In areas with a long land-use history such as the Mediterranean, clear signs indicating the advanced degradation status of the landscape, such as heavily truncated soils, are visible throughout. Soil conservation practices are then aimed at reducing erosion to geological rates, in equilibrium with long-term soil formation rates, while maximizing agricultural production. The adoption of such practices in most areas of the world are as old as the earliest soil erosion episodes themselves. This work firstly reviews historical evidence linking soil management and soil erosion intensity, with examples from N Europe and the Mediterranean. In particular, work by the authors in olive orchards will be presented that shows how significant variations in soil erosion rates between could be linked to the historical soil management. The potential of historical documents for calibrating a soil erosion model is shown as the model, in this case RUSLE-based and combining tillage and water erosion, adequately represents the measured erosion rate dynamics. Secondly, results from present-day, long-term farm experiments in the EU are reviewed to evaluate the effect of different soil management practices on physical soil properties, such as bulk density, penetration resistance, aggregate stability, runoff coefficient or sediment yield. Finally, we reflect upon model and field data that indicate how future global climate change is expected to affect soil management and erosion and how the examples used above hold clues about sustainable historical management practices that can be used successfully in the future.

Dental caries and erosion status of 12-year-old Hong Kong children.

PubMed

Zhang, Shinan; Chau, Alex Mh; Lo, Edward Cm; Chu, Chun-Hung

2014-01-08

This study aimed to assess the dental caries and erosion status of 12-year-old Hong Kong children and study the determinants of dental caries and dental erosion of these children. The survey was performed from 2011 to 2012 with ethics approval. Stratified random sampling was adopted to select 12-year-old children in 7 primary schools in Hong Kong. The participating parents were asked to complete a self-administered questionnaire concerning their children's diet and oral health habits. The children were examined for caries status with WHO criteria by 3 calibrated examiners. Detection of dental erosion followed Basic Erosive Wear Examination (BEWE) criteria. A total of 704 children were recruited and 600 (316 boys, 53%) participated in the survey. There were 124 children (21%) with caries experience (DMFT > 0) and their DMFT was 0.34 ± 0.76. About half of their decay was unfilled (DT = 0.16 ± 0.52) The DMFT of girls and boys were 0.45 ± 0.89 and 0.23 ± 0.61, respectively (p = 0.001). Girls also had a higher DT (0.21 ± 0.62 compared with 0.11 ± 0.41, p = 0.013) and FT than boys (0.23 ± 0.63 compared with 0.12 ± 0.44, p = 0.016). Most children (75%) had at least some sign of erosion (BEWE > 0), but no severe erosion (BEWE = 3). Logistic regression showed girls who consumed soft drinks and took vitamin C supplements had higher caries risk. Dental erosion was more severe among the children who had caries experience and consumed fruit juice. The 12-year-old Hong Kong children had low caries experience, and almost half of the decay was left untreated. Although severe erosion was not found, many children had early signs of erosion.

Uncertainties in assessing tillage erosion - How appropriate are our measuring techniques?

NASA Astrophysics Data System (ADS)

Fiener, P.; Wilken, F.; Aldana-Jague, E.; Deumlich, D.; Gómez, J. A.; Guzmán, G.; Hardy, R. A.; Quinton, J. N.; Sommer, M.; Van Oost, K.; Wexler, R.

2018-03-01

Tillage erosion on arable land is a very important process leading to a net downslope movement of soil and soil constitutes. Tillage erosion rates are commonly in the same order of magnitude as water erosion rates and can be even higher, especially under highly mechanized agricultural soil management. Despite its prevalence and magnitude, tillage erosion is still understudied compared to water erosion. The goal of this study was to bring together experts using different techniques to determine tillage erosion and use the different results to discuss and quantify uncertainties associated with tillage erosion measurements. The study was performed in northeastern Germany on a 10 m by 50 m plot with a mean slope of 8%. Tillage erosion was determined after two sequences of seven tillage operations. Two different micro-tracers (magnetic iron oxide mixed with soil and fluorescent sand) and one macro-tracer (passive radio-frequency identification transponders (RFIDs), size: 4 × 22 mm) were used to directly determine soil fluxes. Moreover, tillage induced changes in topography were measured for the entire plot with two different terrestrial laser scanners and an unmanned aerial system for structure from motion topography analysis. Based on these elevation differences, corresponding soil fluxes were calculated. The mean translocation distance of all techniques was 0.57 m per tillage pass, with a relatively wide range of mean soil translocation distances ranging from 0.39 to 0.72 m per pass. A benchmark technique could not be identified as all used techniques have individual error sources, which could not be quantified. However, the translocation distances of the macro-tracers used were consistently smaller than the translocation distances of the micro-tracers (mean difference = - 26 ± 12%), which questions the widely used assumption of non-selective soil transport via tillage operations. This study points out that tillage erosion measurements, carried out under almost optimal conditions, are subject to major uncertainties that are far from negligible.

Atomic Oxygen Erosion Yield Prediction for Spacecraft Polymers in Low Earth Orbit

NASA Technical Reports Server (NTRS)

Banks, Bruce A.; Backus, Jane A.; Manno, Michael V.; Waters, Deborah L.; Cameron, Kevin C.; deGroh, Kim K.

2009-01-01

The ability to predict the atomic oxygen erosion yield of polymers based on their chemistry and physical properties has been only partially successful because of a lack of reliable low Earth orbit (LEO) erosion yield data. Unfortunately, many of the early experiments did not utilize dehydrated mass loss measurements for erosion yield determination, and the resulting mass loss due to atomic oxygen exposure may have been compromised because samples were often not in consistent states of dehydration during the pre-flight and post-flight mass measurements. This is a particular problem for short duration mission exposures or low erosion yield materials. However, as a result of the retrieval of the Polymer Erosion and Contamination Experiment (PEACE) flown as part of the Materials International Space Station Experiment 2 (MISSE 2), the erosion yields of 38 polymers and pyrolytic graphite were accurately measured. The experiment was exposed to the LEO environment for 3.95 years from August 16, 2001 to July 30, 2005 and was successfully retrieved during a space walk on July 30, 2005 during Discovery s STS-114 Return to Flight mission. The 40 different materials tested (including Kapton H fluence witness samples) were selected specifically to represent a variety of polymers used in space as well as a wide variety of polymer chemical structures. The MISSE 2 PEACE Polymers experiment used carefully dehydrated mass measurements, as well as accurate density measurements to obtain accurate erosion yield data for high-fluence (8.43 1021 atoms/sq cm). The resulting data was used to develop an erosion yield predictive tool with a correlation coefficient of 0.895 and uncertainty of +/-6.3 10(exp -25)cu cm/atom. The predictive tool utilizes the chemical structures and physical properties of polymers to predict in-space atomic oxygen erosion yields. A predictive tool concept (September 2009 version) is presented which represents an improvement over an earlier (December 2008) version.

Modeling long-term suspended-sediment export from an undisturbed forest catchment

NASA Astrophysics Data System (ADS)

Zimmermann, Alexander; Francke, Till; Elsenbeer, Helmut

2013-04-01

Most estimates of suspended sediment yields from humid, undisturbed, and geologically stable forest environments fall within a range of 5 - 30 t km-2 a-1. These low natural erosion rates in small headwater catchments (≤ 1 km2) support the common impression that a well-developed forest cover prevents surface erosion. Interestingly, those estimates originate exclusively from areas with prevailing vertical hydrological flow paths. Forest environments dominated by (near-) surface flow paths (overland flow, pipe flow, and return flow) and a fast response to rainfall, however, are not an exceptional phenomenon, yet only very few sediment yields have been estimated for these areas. Not surprisingly, even fewer long-term (≥ 10 years) records exist. In this contribution we present our latest research which aims at quantifying long-term suspended-sediment export from an undisturbed rainforest catchment prone to frequent overland flow. A key aspect of our approach is the application of machine-learning techniques (Random Forest, Quantile Regression Forest) which allows not only the handling of non-Gaussian data, non-linear relations between predictors and response, and correlations between predictors, but also the assessment of prediction uncertainty. For the current study we provided the machine-learning algorithms exclusively with information from a high-resolution rainfall time series to reconstruct discharge and suspended sediment dynamics for a 21-year period. The significance of our results is threefold. First, our estimates clearly show that forest cover does not necessarily prevent erosion if wet antecedent conditions and large rainfalls coincide. During these situations, overland flow is widespread and sediment fluxes increase in a non-linear fashion due to the mobilization of new sediment sources. Second, our estimates indicate that annual suspended sediment yields of the undisturbed forest catchment show large fluctuations. Depending on the frequency of large events, annual suspended-sediment yield varies between 74 - 416 t km-2 a-1. Third, the estimated sediment yields exceed former benchmark values by an order of magnitude and provide evidence that the erosion footprint of undisturbed, forested catchments can be undistinguishable from that of sustainably managed, but hydrologically less responsive areas. Because of the susceptibility to soil loss we argue that any land use should be avoided in natural erosion hotspots.

Sediment dynamics in an overland flow-prone forest catchment

NASA Astrophysics Data System (ADS)

Zimmermann, Alexander; Elsenbeer, Helmut

2010-05-01

Vegetation controls erosion in many respects, and it is assumed that forest cover is an effective control. Currently, most literature on erosion processes in forest ecosystems support this impression and estimates of sediment export from forested catchments serve as benchmarks to evaluate erosion processes under different land uses. Where soil properties favor near-surface flow paths, however, vegetation may not mitigate surface erosion. In the forested portion of the Panama Canal watershed overland flow is widespread and occurs frequently, and indications of active sediment transport are hard to overlook. In this area we selected a 9.7 ha catchment for a high-resolution study of suspended sediment dynamics. We equipped five nested catchments to elucidate sources, drivers, magnitude and timing of suspended sediment export by continuous monitoring of overland flow and stream flow and by simultaneous, event-based sediment sampling. The support program included monitoring throughfall, splash erosion, overland-flow connectivity and a survey of infiltrability, permeability, and aggregate stability. This dataset allowed a comprehensive view on erosion processes. We found that overland flow controls the suspended-sediment dynamics in channels. Particularly, rainfalls of high intensity at the end of the rainy season have a superior impact on the overall sediment export. During these events, overland flow occurs catchment-wide up to the divide and so does erosion. With our contribution we seek to provide evidence that forest cover and large sediment yields are no contradiction in terms even in the absence of mass movements.

Oxygen plasma treatment and deposition of CN{sub x} on a fluorinated polymer matrix composite for improved erosion resistance

DOE Office of Scientific and Technical Information (OSTI.GOV)

Muratore, C.; Korenyi-Both, A.; Bultman, J. E.

2007-07-15

The use of polymer matrix composites in aerospace propulsion applications is currently limited by insufficient resistance to erosion by abrasive media. Erosion resistant coatings may provide necessary protection; however, adhesion to many high temperature polymer matrix composite (PMC) materials is poor. A low pressure oxygen plasma treatment process was developed to improve adhesion of CN{sub x} coatings to a carbon reinforced, fluorinated polymer matrix composite. Fullerene-like CN{sub x} was selected as an erosion resistant coating for its high hardness-to-elastic modulus ratio and elastic resilience which were expected to reduce erosion from media incident at different angles (normal or glancing) relativemore » to the surface. In situ x-ray photoelectron spectroscopy was used to evaluate the effect of the plasma treatment on surface chemistry, and electron microscopy was used to identify changes in the surface morphology of the PMC substrate after plasma exposure. The fluorine concentration at the surface was significantly reduced and the carbon fibers were exposed after plasma treatment. CN{sub x} coatings were then deposited on oxygen treated PMC substrates. Qualitative tests demonstrated that plasma treatment improved coating adhesion resulting in an erosion resistance improvement of a factor of 2 compared to untreated coated composite substrates. The combination of PMC pretreatment and coating with CN{sub x} reduced the erosion rate by an order of magnitude for normally incident particles.« less

Erosion under climate and human pressures: An alpine lake sediment perspective

NASA Astrophysics Data System (ADS)

Arnaud, Fabien; Poulenard, Jérôme; Giguet-Covex, Charline; Wilhelm, Bruno; Révillon, Sidonie; Jenny, Jean-Philippe; Revel, Marie; Enters, Dirk; Bajard, Manon; Fouinat, Laurent; Doyen, Elise; Simonneau, Anaëlle; Pignol, Cécile; Chapron, Emmanuel; Vannière, Boris; Sabatier, Pierre

2016-11-01

We review the scientific efforts over the last decades to reconstruct erosion from continuous alpine lake sediment records. We focused both on methodological issues, showing the growing importance of non-destructive high resolution approaches (XRF core-scanner) as well as progresses in the understanding of processes leading to the creation of an "erosion signal" in lakes. We distinguish "continuous records" from "event-records". Both provide complementary information but need to be studied with different approaches. Continuous regionally-relevant records proved to be particularly pertinent to document regional erosion patterns throughout the Holocene, in particular applying the source to sink approach. Event-based approaches demonstrated and took advantage of the strong non-linearity of sediment transport in high altitude catchment areas. This led to flood frequency and intensity reconstructions, highlighting the influence of climate change upon flood dynamics in the mountain. The combination of different record types, both in terms of location (high vs. low elevation), sedimentology (high vs. low terrigenous contribution) and significance (local vs. regional) is one of the main outputs of this paper. It allows the establishment of comprehensive histories of NW French Alps erosion, but also and consequently, soil dynamics and hydrological patterns throughout the Holocene. We also discuss the influence of glacier dynamics, one of the major agents of erosion in the Alps. A major feature is the growing human influence upon erosion at a local scale since at least the middle of the Bronze Age (3500 cal. BP). However and according to the regional record from Lake Bourget, only few periods of rising erosion at local scales generated a regional record that can be discriminated from wetter climatic periods. Among them, the period between 200 BCE and 400 AD appeared to be marked by a generalised rise in human-triggered erosion at local scales in the northern French Alps. This review highlights the importance of modern high-resolution and interdisciplinary studies of lake sediments, in order to better understand the complex relationships between humans, climate and the Earth system in general. We strongly argue that regional integration of data is now required to move a step further. Such an integration is easier with cost- and time-effective methods as well as after a better definition of approaches and their limits. This should lead to a stronger collaboration between paleo-data producers and modellers in the near future.

Induction furnace testing of the durability of prototype crucibles in a molten metal environment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jablonski, Paul D.

2005-09-01

Engineered ceramic crucibles are commonly used to contain molten metal. Besides high temperature stability, other desired crucible characteristics include thermal shock resistance, minimal reaction with the molten metal and resistance to attack from the base metal oxide formed during melting. When used in an induction furnace, they can be employed as a “semi-permanent” crucible incorporating a dry ram backup and a ceramic cap. This report covers several 250-lb single melt crucible tests in an air melt induction furnace. These tests consisted of melting a charge of 17-4PH stainless steel, holding the charge molten for two hours before pouring off themore » heat and then subsequently sectioning the crucible to review the extent of erosion, penetration and other physical characteristics. Selected temperature readings were made throughout each melt. Chemistry samples were also taken from each heat periodically throughout the hold. The manganese level was observed to affect the rate of chromium loss in a non-linear fashion.« less

Evaluation of Time-Varying Hydrology within the Training Range Environmental Evaluation and Characterization System (TREECS TM)

DTIC Science & Technology

2014-08-01

daily) hydrology UI user interface of a model USGS U.S. Geological Survey USLE Universal Soil Loss Equation used to compute soil erosion rate for...SCS curve number runoff method, inches or m It daily infiltration rate for day t, m/day K soil erodibility factor in the USLE and MUSLE L length...and soil erosion (using the Universal Soil Loss Equation, or USLE ) as a reference even when time-varying hydrology is selected for use. The UI also

Lymphocytic gastritis: a newly described entity: a retrospective endoscopic and histological study.

PubMed Central

Haot, J; Hamichi, L; Wallez, L; Mainguet, P

1988-01-01

Lymphocytic gastritis is a histopathological entity characterised by the accumulation of small lymphocytes in the surface and foveolar epithelium. In order to investigate the correlation between endoscopy and histology in this condition, 192 observations selected on the basis of a presumed diagnosis of erosive or varioliform gastritis were reviewed. Ninety two instances corresponded to lymphocytic gastritis, while 100 did not show any particular microscopic feature and were labelled non-specific gastritis. There was a good correlation (48 of 58) between the diagnosis of the so-called varioliform gastritis and the histological evidence of lymphocytic gastritis. The correlation was even better when nodules, erosions, and enlarged folds were considered. Lymphocytic gastritis has a typical endoscopical appearance consisting of nodules, erosions, and large folds predominating in the gastric body. This contrasts with non-specific gastritis, which affects the antrum and produces erosions on a flat mucosa. Images Fig. 1 Fig. 2 Fig. 3 Fig. 4 Fig. 5 Fig. 6 PMID:3198002

Simulating CRN derived erosion rates in a transient Andean catchment using the TTLEM model

NASA Astrophysics Data System (ADS)

Campforts, Benjamin; Vanacker, Veerle; Herman, Frédéric; Schwanghart, Wolfgang; Tenrorio Poma, Gustavo; Govers, Gerard

2017-04-01

Assessing the impact of mountain building and erosion on the earth surface is key to reconstruct and predict terrestrial landscape evolution. Landscape evolution models (LEMs) are an essential tool in this research effort as they allow to integrate our growing understanding of physical processes governing erosion and transport of mass across the surface. The recent development of several LEMs opens up new areas of research in landscape evolution. Here, we want to seize this opportunity by answering a fundamental research question: does a model designed to simulate landscape evolution over geological timescales allows to simulate spatially varying erosion rates at a millennial timescale? We selected the highly transient Paute catchment in the Southeastern Ecuadorian Andes as a study area. We found that our model (TTLEM) is capable to better explain the spatial patterns of ca. 30 Cosmogenic Radio Nuclide (CRN) derived catchment wide erosion rates in comparison to a classical, statistical approach. Thus, the use of process-based landscape evolution models may not only be of great help to understand long-term landscape evolution but also in understanding spatial and temporal variations in sediment fluxes at the millennial time scale.

The evolution of concepts for soil erosion modelling

NASA Astrophysics Data System (ADS)

Kirkby, Mike

2013-04-01

From the earliest models for soil erosion, based on power laws relating sediment discharge or yield to slope length and gradient, the development of the Universal Soil Loss Equation was a natural step, although one that has long continued to hinder the development of better perceptual models for erosion processes. Key stumbling blocks have been: 1. The failure to go through runoff generation as a key intermediary 2. The failure to separate hydrological and strength parameters of the soil 3. The failure to treat sediment transport along a slope as a routing problem 4. The failure to analyse the nature of the dependence on vegetation Key advances have been in these directions (among others) 1. Improved understanding of the hydrological processes (e.g. infiltration and runoff, sediment entrainment) leading to KINEROS, LISEM,WEPP, PESERA 2. Recognition of selective sediment transport (e.g. transport- or supply-limited removal, grain travel distances) leading e.g. to MAHLERAN 3. Development of models adapted to particular time/space scales Some major remaining problems 1. Failure to integrate geomorphological and agronomic approaches 2. Tillage erosion - Is erosion loss of sediment or lowering of centre of mass? 3. Dynamic change during an event, as rills etc form.

The Characteristics of Extreme Erosion Events in a Small Mountainous Watershed

PubMed Central

Fang, Nu-Fang; Shi, Zhi-Hua; Yue, Ben-Jiang; Wang, Ling

2013-01-01

A large amount of soil loss is caused by a small number of extreme events that are mainly responsible for the time compression of geomorphic processes. The aim of this study was to analyze suspended sediment transport during extreme erosion events in a mountainous watershed. Field measurements were conducted in Wangjiaqiao, a small agricultural watershed (16.7 km2) in the Three Gorges Area (TGA) of China. Continuous records were used to analyze suspended sediment transport regimes and assess the sediment loads of 205 rainfall–runoff events during a period of 16 hydrological years (1989–2004). Extreme events were defined as the largest events, ranked in order of their absolute magnitude (representing the 95th percentile). Ten extreme erosion events from 205 erosion events, representing 83.8% of the total suspended sediment load, were selected for study. The results of canonical discriminant analysis indicated that extreme erosion events are characterized by high maximum flood-suspended sediment concentrations, high runoff coefficients, and high flood peak discharge, which could possibly be explained by the transport of deposited sediment within the stream bed during previous events or bank collapses. PMID:24146898

A multi-sensor approach to assess erosion risk in low mountain range landscapes - a comparative case study in western Germany

NASA Astrophysics Data System (ADS)

Seeling, S.; Buddenbaum, H.; Seeger, M.; Löhnertz, M.

2009-04-01

In this presentation we summarize our experience in the derivation of variables for identification of erosion and areas endagered of erosion from different remote sensing sensors. The field study is situated at the "Zemmer-Plateau" (north-east from Trier) and was undertaken to compare the ability of different, passive and active, remote sensing sensors to derive several process parameters of soil erosion in agricultural landscapes. Additionally the added value of sensor combinations was investigated. Backscatter of C-Band microwave instruments is known to be sensitive to soil roughness and surface soil moisture. If landuse and roughness is approximately constant, backscatter is mostly affected by temporal changes in soil moisture. For the test site multitemporal imagery from the ASAR and ERS2 sensors was available. For the identification of areas prone to waterlogging an approach based on principal component analysis was used. Multitemporal imagery from optical sensors like Landsat and SPOT HRV allow the assessment of slow changes within the landscape and annual changes of vegetation cover. We used Landsat imagery from 1975, 1984 and 2000 to map the changes in landuse and associated soil development, multi temporal imagery from SPOT 4 and 5 satellites was used to identify different crop types. Additionally we investigated which areas that are prone to erosion by their topography position, have, due to maladjusted land management, not been protected by vegetation cover during the main annual rainfall season in 2003. Airborne Laser Scanning (ALS) data is well suited for discovering areas susceptible of erosion. Even under forest canopies ALS can provide high-resolution terrain models that can be used for identifying trenches, linear features, steep hills and other terrain features, which trigger erosion or are even results of erosion. ALS-derived DTMs usually have a spatial resolution of about 1 m, while DTMs from other data sources are much coarser. A key problem when working with ALS is finding the echoes that have really been reflected by the ground and not by buildings or vegetation. This is achieved by filtering the last and only return laser points. The investigations were aided be the analyses of two Quickbird datasets. The information layers derived from different sensors were merged into a preliminary erosion information system. This data base allows the identification of areas prone to erosion risk. Furthermore the results allow setting the focus on the most effective methods for further investigations.

Erosion and deterioration of the Isles Dernieres Barrier Island Arc, Louisiana, U.S.A.: 1853 to 1988

USGS Publications Warehouse

McBride, Randolph A.; Penland, Shea; Jaffe, Bruce E.; Williams, S. Jeffress; Sallenger, Asbury H.; Westphal, Karen A.

1989-01-01

Using cartographic and aerial photography data from the years 1853, 1890, 1934, 1956, 1978, 1984, and 1988, shoreline change maps of the Isles Dernieres barrier island arc were constructed. These data were accurately superimposed, using a computer mapping system, which removed projection, datum, scale, and other cartographic inconsistencies. Linear, areal, and perimeter measurements indicate that the Isles Dernieres are suffering rapid rates of coastal erosion, land loss, and breakup. Bayside and gulfside erosion, in combination with sediment shortage and subsidence, have caused the Isles Dernieres to narrow through time. In addition, the core of the barrier island arc does not migrate landward and instead, breaks up in place as a result of inlet breaching and development. This is in contrast to other models of landward barrier island migration during transgression. If these trends continue, the Isles Dernieres will likely evolve into a subaqueous inner-shelf shoal by the early 21st century. Loss of the Isles Dernieres barrier island arc will severely impact the Terrebonne parish estuary, resulting in decreased environmental quality and increased public risk from storms and hurricanes.

[Analysis of hydrodynamics parameters of runoff erosion and sediment-yielding on unpaved road].

PubMed

Huang, Peng-Fei; Wang, Wen-Long; Luo, Ting; Wang, Zhen; Wang, Zheng-Li; Li, Ren

2013-02-01

By the method of field runoff washout experiment, a simulation study was conducted on the relationships between the soil detachment rate and the hydrodynamic parameters on unpaved road, and the related quantitative formulas were established. Under the conditions of different flow discharges and road gradients, the averaged soil detachment rate increased with increasing flow discharge and road gradient, and the relationships between them could be described by a power function. As compared with road gradient, flow discharge had greater effects on the soil detachment rate. The soil detachment rate had a power relation with water flow velocity and runoff kinetic energy, and the runoff kinetic energy was of importance to the soil detachment rate. The soil detachment rate was linearly correlated with the unit runoff kinetic energy. The averaged soil erodibility was 0.120 g m-1.J-F-1, and the averaged critical unit runoff kinetic energy was 2.875 g.m-1.J-1. Flow discharge, road gradient, and unit runoff kinetic energy could be used to accurately describe the soil erosion process and calculate the soil erosion rate on unpaved road.

The influence of different factors on in vitro enamel erosion.

PubMed

Lussi, A; Jäggi, T; Schärer, S

1993-01-01

The aim of this study was to use two demineralization test methods to analyze the erosive potential of beverages and foodstuffs. In addition, the surface microhardness test and the iodide permeability test were compared. Surface microhardness and iodide permeability were measured before and after exposure. To characterize the beverages and foodstuffs the content of phosphate, calcium and fluoride, pH, the titrable amount of base to pH 5.5 and 7.0 as well as the buffer capacity at pH 5.5 were determined. Sprite light showed the highest significant decrease in surface microhardness (p < or = 0.05) followed by grapefruit juice, apple juice and salad dressing. The highest significant increase in iodide permeability (p < or = 0.05) was caused by exposure to grapefruit juice followed by apple juice (Sprite light was not tested). Multiple linear regression analyses revealed that the erosive capacity of different drinks, juices and foodstuffs are statistically significantly associated with their acidity, pH values, phosphate and fluoride contents as well as the baseline surface microhardness or iodide permeability values of the exposed enamel.

Coastal erosion and mass wasting along the Canadian Beaufort Sea based on annual airborne LiDAR elevation data

NASA Astrophysics Data System (ADS)

Obu, Jaroslav; Lantuit, Hugues; Grosse, Guido; Günther, Frank; Sachs, Torsten; Helm, Veit; Fritz, Michael

2017-09-01

Erosion of permafrost coasts has received increasing scientific attention since 1990s because of rapid land loss and the mobilisation potential of old organic carbon. The majority of permafrost coastal erosion studies are limited to time periods from a few years to decades. Most of these studies emphasize the spatial variability of coastal erosion, but the intensity of inter-annual variations, including intermediate coastal aggradation, remains poorly documented. We used repeat airborne Light Detection And Ranging (LiDAR) elevation data from 2012 and 2013 with 1 m horizontal resolution to study coastal erosion and accompanying mass-wasting processes in the hinterland. Study sites were selected to include different morphologies along the coast of the Yukon Coastal Plain and on Herschel Island. We studied elevation and volume changes and coastline movement and compared the results between geomorphic units. Results showed simple uniform coastal erosion from low coasts (up to 10 m height) and a highly diverse erosion pattern along coasts with higher backshore elevation. This variability was particularly pronounced in the case of active retrogressive thaw slumps, which can decrease coastal erosion or even cause temporary progradation by sediment release. Most of the extremes were recorded in study sites with active slumping (e.g. 22 m of coastline retreat and 42 m of coastline progradation). Coastline progradation also resulted from the accumulation of slope collapse material. These occasional events can significantly affect the coastline position on a specific date and can affect coastal retreat rates as estimated in long term by coastline digitalisation from air photos and satellite imagery. These deficiencies can be overcome by short-term airborne LiDAR measurements, which provide detailed and high-resolution information about quickly changing elevations in coastal areas.

The effect of magnesium hydroxide-containing dentifrice using an extrinsic and intrinsic erosion cycling model.

PubMed

Passos, Vanara Florêncio; Rodrigues, Lidiany Karla Azevedo; Santiago, Sérgio Lima

2018-02-01

To evaluate, in vitro, the effect of Mg(OH) 2 dentifrice, and the influence of the number of experimental days, on the extrinsic (citric acid -CA) and intrinsic (hydrochloric acid -HCl) enamel erosion models. Human enamel slabs were selected according to surface hardness and randomly assigned to 3 groups (n=9) as follows: non-fluoridated (negative control), NaF (1450ppm F- positive control) and Mg(OH) 2 (2%) dentifrices. The slabs were daily submitted to a 2-h period of pellicle formation and, over a period of 5days, submitted to cycles (3×/day) of erosive challenge (CA 0.05M, pH=3.75 or HCl 0.01M, pH=2 for 30s), treatment (1min -1:3w/w of dentifrice/distilled water) and remineralization (artificial saliva/120min). Enamel changes were determined by surface hardness loss (SHL) for each day and mechanical profilometry analysis. Data were analyzed by two-way ANOVA followed by Tukey's test to % SHL and one-way ANOVA to profilometry (p<0.05). The number of experimental days influenced the erosion process for the two types of erosion models (p<0.001). Mg(OH) 2 -containing dentifrices were effective in reducing enamel extrinsic acid erosion as determined by % SHL (p<0.001) when compared to the control group, being better than positive control (p<0.001); however, the dentifrices were not effective for the intrinsic model (p=0.295). With regards to surface wear, no statistically significant differences were found among the groups for CA (p=0.225) and HCl (p=0.526). The findings suggest that Mg(OH) 2 dentifrices might protect enamel against slight erosion, but protection was not effective for stronger acid erosion. Copyright © 2017 Elsevier Ltd. All rights reserved.

Predicting orogenic wedge styles as a function of analogue erosion law and material softening

NASA Astrophysics Data System (ADS)

Mary, Baptiste C. L.; Maillot, Bertrand; Leroy, Yves M.

2013-10-01

The evolution of a compressive frictional wedge on a weak, frictional and planar décollement, subjected to frontal accretion, is predicted with a two step method called sequential limit analysis. The first step consists in finding, with the kinematic approach of limit analysis, the length of the active décollement and the dips of the emerging ramp and of the conjugate shear plane composing the emerging thrust fold. The second step leads to a modification of the geometry, first, because of the thrust fold development due to compression and, second, because of erosion. Erosion consists in removing periodically any material above a fictitious line at a selected slope, as done in analogue experiments. This application of sequential limit analysis generalizes the critical Coulomb wedge theory since it follows the internal deformation development. With constant frictional properties, the deformation is mostly diffuse, a succession of thrust folds being activated so that the topographic slope reaches exactly the theoretical, critical value. Frictional weakening on the ramps results in a deformation style composed of thrust sheets and horses. Applying an erosion slope at the critical topographic value leads to exhumation in the frontal, central, or rear region of the wedge depending on the erosion period and the weakening. Erosion at slopes slightly above or below the critical value results in exhumation toward the foreland or the hinterland, respectively, regardless of the erosion period. Exhumation is associated with duplexes, imbricate fans, antiformal stacks, and major backthrusting. Comparisons with sandbox experiments confirm that the thickness, dips, vergence, and exhumation of thrust sheets can be reproduced with friction and erosion parameters within realistic ranges of values.

Mechanical weathering and rock erosion by climate-dependent subcritical cracking

NASA Astrophysics Data System (ADS)

Eppes, Martha-Cary; Keanini, Russell

2017-06-01

This work constructs a fracture mechanics framework for conceptualizing mechanical rock breakdown and consequent regolith production and erosion on the surface of Earth and other terrestrial bodies. Here our analysis of fracture mechanics literature explicitly establishes for the first time that all mechanical weathering in most rock types likely progresses by climate-dependent subcritical cracking under virtually all Earth surface and near-surface environmental conditions. We substantiate and quantify this finding through development of physically based subcritical cracking and rock erosion models founded in well-vetted fracture mechanics and mechanical weathering, theory, and observation. The models show that subcritical cracking can culminate in significant rock fracture and erosion under commonly experienced environmental stress magnitudes that are significantly lower than rock critical strength. Our calculations also indicate that climate strongly influences subcritical cracking—and thus rock weathering rates—irrespective of the source of the stress (e.g., freezing, thermal cycling, and unloading). The climate dependence of subcritical cracking rates is due to the chemophysical processes acting to break bonds at crack tips experiencing these low stresses. We find that for any stress or combination of stresses lower than a rock's critical strength, linear increases in humidity lead to exponential acceleration of subcritical cracking and associated rock erosion. Our modeling also shows that these rates are sensitive to numerous other environment, rock, and mineral properties that are currently not well characterized. We propose that confining pressure from overlying soil or rock may serve to suppress subcritical cracking in near-surface environments. These results are applicable to all weathering processes.

Mountain river meanders and typhoon strike frequency in the western Pacific

NASA Astrophysics Data System (ADS)

Stark, C. P.; Barbour, J.; Hsieh, M.; Hovius, N.; Jen, C.; Chen, M.

2004-12-01

Bedrock-floored mountain rivers are shaped by erosion processes that ultimately control the evolution of the landscape on geological time scales. In mountains across the western Pacific, meanders in bedrock channels are common and often emerge during incision rather than inherit their sinuosity from a past alluvial form. Incising emergent meanders are important because they reveal a process of lateral channel erosion at least as fast as the vertical rate erosion. Here we report a remarkable link between incised meander development and typhoon strike frequency, a good proxy for extreme rainfall and flood discharge. Using satellite imagery, shuttle-radar topographic data and a 58~year inventory of typhoon tracks, we mapped meander abundance and quantified regional densities of mountain river sinuosity and typhoon strikes. Our analysis shows that eroding meanders are most common in the typhoon-prone islands of Japan, Taiwan and the Philippines, and in rivers incising weak lithologies. One might expect that the faster the erosion rate, the greater the meandering, but we have found that monthly mean rainfall - and therefore mean discharge - correlates very poorly with sinuosity. Instead, the variability of rainfall, and presumably discharge, about the mean explains bedrock meander development much better. Mountain river sinuosity, for geologically similar bedrock, increases in a roughly linear fashion with typhoon strike frequency. The coefficient of variation of monthly rainfall (standard deviation normalized by the mean) exhibits a similar trend. We deduce that extreme flood discharge, e.g. driven by typhoon rainfall, accelerates lateral erosion rates and spurs meander development in mountain rivers.

Contrasting landform perception with varied radar illumination geometries and at simulated resolutions of Venera and Magellan

NASA Technical Reports Server (NTRS)

Ford, J. P.; Arvidson, R. E.

1989-01-01

The high sensitivity of imaging radars to slope at moderate to low incidence angles enhances the perception of linear topography on images. It reveals broad spatial patterns that are essential to landform mapping and interpretation. As radar responses are strongly directional, the ability to discriminate linear features on images varies with their orientation. Landforms that appear prominent on images where they are transverse to the illumination may be obscure to indistinguishable on images where they are parallel to it. Landform detection is also influenced by the spatial resolution in radar images. Seasat radar images of the Gran Desierto Dunes complex, Sonora, Mexico; the Appalachian Valley and Ridge Province; and accreted terranes in eastern interior Alaska were processed to simulate both Venera 15 and 16 images (1000 to 3000 km resolution) and image data expected from the Magellan mission (120 to 300 m resolution. The Gran Desierto Dunes are not discernable in the Venera simulation, whereas the higher resolution Magellan simulation shows dominant dune patterns produced from differential erosion of the rocks. The Magellan simulation also shows that fluvial processes have dominated erosion and exposure of the folds.

Origin and lateral migration of linear dunes in the Qaidam Basin of NW China revealed by dune sediments, internal structures, and optically stimulated luminescence ages, with implications for linear dunes on Titan: discussion

USGS Publications Warehouse

Rubin, David M.; Rubin, Alan M.

2013-01-01

Zhou et al. (2012) proposed that longitudinal dunes in the Qaidam Basin, China, formed like yardangs: by erosion into sediment that was not deposited by those dunes. Because erosion occurs on the upwind flanks of most migrating dunes (Rubin and Hunter, 1982, 1985), the key to demonstrating a yardang-like origin is to show that the dunes did not deposit the strata that they contain. Zhou et al. made this argument by proposing that: (1) The dunes have not deposited cross-strata in the past 810 yr. (2) Cross-bedding within the dunes was not deposited by the dunes on the present-day land surface, but rather by older dunes that had a different morphology. (3) The present dunes are a later generation, “most likely of erosional origin similar to yardangs with orientations controlled by strikes of joints,” (p. 1147). (4) Rates of deflation in the dune field have been extremely high for the past 810–2440 yr. This commentary reviews these conclusions, reviews contradictory observations, and considers alternative interpretations.

Use of multi-temporal SPOT-5 satellite images for land degradation assessment in Cameron Highlands, Malaysia using Geospatial techniques

NASA Astrophysics Data System (ADS)

Nampak, Haleh; Pradhan, Biswajeet

2016-07-01

Soil erosion is the common land degradation problem worldwide because of its economic and environmental impacts. Therefore, land-use change detection has become one of the major concern to geomorphologists, environmentalists, and land use planners due to its impact on natural ecosystems. The objective of this paper is to evaluate the relationship between land use/cover changes and land degradation in the Cameron highlands (Malaysia) through multi-temporal remotely sensed satellite images and ancillary data. Land clearing in the study area has resulted increased soil erosion due to rainfall events. Also unsustainable development and agriculture, mismanagement and lacking policies contribute to increasing soil erosion rates. The LULC distribution of the study area was mapped for 2005, 2010, and 2015 through SPOT-5 satellite imagery data which were classified based on object-based classification. A soil erosion model was also used within a GIS in order to study the susceptibility of the areas affected by changes to overland flow and rain splash erosion. The model consists of four parameters, namely soil erodibility, slope, vegetation cover and overland flow. The results of this research will be used in the selection of the areas that require mitigation processes which will reduce their degrading potential. Key words: Land degradation, Geospatial, LULC change, Soil erosion modelling, Cameron highlands.

Dynamic soil properties in response to anthropogenic disturbance

NASA Astrophysics Data System (ADS)

Vanacker, Veerle; Ortega, Raúl

2013-04-01

Anthropogenic disturbance of natural vegetation can profoundly alter the physical, chemical and biological processes within soils. Rapid removal of topsoil during intense farming can result in an imbalance between soil production through chemical weathering and physical erosion, with direct implications on local biogeochemical cycling. However, the feedbacks between soil erosion, chemical weathering and biogeochemical cycling in response to anthropogenic forcing are not yet fully understood. Here, we study dynamic soil properties for a rapidly changing anthropogenic landscape, and focus on the coupling between physical erosion, soil production and soil chemical weathering. The archaeological site of Santa Maria de Melque (Toledo, Central Spain) was selected for its remarkably long occupation history dating back to the 7th century AD. As part of the agricultural complex, four retention reservoirs were built in the Early Middle Ages. The sedimentary archive was used to track the evolution in sedimentation rates and geochemical properties of the sediment. Catchment-wide soil erosion rates vary slightly between the various occupation phases (7th century-now), but are of the same magnitude as the cosmogenic nuclide-derived erosion rates. However, there exists large spatial variation in physical erosion rates that are coupled with chemical weathering intensities. The sedimentary records suggest that there are important changes in the spatial pattern of sediment source areas through time as a result of changing land use patterns

Gastroesophageal reflux, dental erosion, and halitosis in epidemiological surveys: a systematic review.

PubMed

Marsicano, Juliane A; de Moura-Grec, Patrícia G; Bonato, Rafaela C S; Sales-Peres, Matheus de Carvalho; Sales-Peres, Arsenio; Sales-Peres, Sílvia Helena de Carvalho

2013-02-01

In published studies, it has been suggested that dental wear is associated with gastroesophageal reflux disease (GERD). This systematic review was carried out to evaluate the association of GERD, dental erosion, and halitosis and to compare the indices adopted in epidemiological surveys. The Medline database (until October, 2011) was searched systematically to identify studies evaluating the prevalence of oral alterations, such as dental erosion and halitosis, in patients with GERD symptoms. Two reviewers analyzed all reports and the selected studies were evaluated according to the quality of evidence, using the validated Newcastle-Ottawa Quality Assessment Scale. Full-text copies of a total of 32 publications were obtained in duplicate. Sixteen publications were identified among the citations in the Bibliographic lists of studies that fulfilled the exclusion/inclusion criteria and quality of evidence. The relationship between dental erosion and GERD patients was significant in only seven studies. According to three studies, halitosis could be one of several extraesophageal symptoms or manifestations in GERD patients. In one study, it was found that the mucosa of GERD patients was significantly more acidic in comparison with that of the control group. This systematic review showed that there is a relationship between GERD and oral diseases (dental erosion and halitosis). The epidemiological surveys used different indices to analyze GERD and dental erosion. Further research could investigate the best method for assessing the two diseases.

Erosion tests of materials by energetic particle beams

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schechter, D.E.; Tsai, C.C.; Sluss, F.

1985-01-01

The internal components of magnetic fusion devices must withstand erosion from and high heat flux of energetic plasma particles. The selection of materials for the construction of these components is important to minimize contamination of the plasma. In order to study various materials' comparative resistance to erosion by energetic particles and their ability to withstand high heat flux, water-cooled copper swirl tubes coated or armored with various materials were subjected to bombardment by hydrogen and helium particle beams. Materials tested were graphite, titanium carbide (TiC), chromium, nickel, copper, silver, gold, and aluminum. Details of the experimental arrangement and methods ofmore » application or attachment of the materials to the copper swirl tubes are presented. Results including survivability and mass losses are discussed.« less

Three mars years: Viking lander 1 imaging observations

USGS Publications Warehouse

Arvidson, R. E.; Guinness, E.A.; Moore, H.J.; Tillman, J.; Wall, S.D.

1983-01-01

The Mutch Memorial Station (Viking Lander 1) on Mars acquired imaging and meteorological data over a period of 2245 martian days (3:3 martian years). This article discusses the deposition and erosion of thin deposits (ten to hundreds of micrometers) of bright red dust associated with global dust storms, and the removal of centimeter amounts of material in selected areas during a dust storm late in the third winter. Atmospheric pressure data acquired during the period of intense erosion imply that baroclinic disturbances and strong diurnal solar tidal heating combined to produce strong winds. Erosion occurred principally in areas where soil cohesion was reduced by earlier surface sampler activities. Except for redistribution of thin layers of materials, the surface appears to be remarkably stable, perhaps because of cohesion of the undisturbed surface material.

Three Mars years: viking lander 1 imaging observations.

PubMed

Arvidson, R E; Guinness, E A; Moore, H J; Tillman, J; Wall, S D

1983-11-04

The Mutch Memorial Station (Viking Lander 1) on Mars acquired imaging and meteorological data over a period of 2245 martian days (3:3 martian years). This article discusses the deposition and erosion of thin deposits (ten to hundreds of micrometers) of bright red dust associated with global dust storms, and the removal of centimeter amounts of material in selected areas during a dust storm late in the third winter. Atmospheric pressure data acquired during the period of intense erosion imply that baroclinic disturbances and strong diurnal solar tidal heating combined to produce strong winds. Erosion occurred principally in areas where soil cohesion was reduced by earlier surface sampler activities. Except for redistribution of thin layers of materials, the surface appears to be remarkably stable, perhaps because of cohesion of the undisturbed surface material.

Three Mars years - Viking Lander 1 imaging observations

NASA Technical Reports Server (NTRS)

Arvidson, R. E.; Guinness, E. A.; Moore, H. J.; Tillman, J.; Wall, S. D.

1983-01-01

The Mutch Memorial Station (Viking Lander 1) on Mars acquired imaging and meteorological data over a period of 2245 martian days (3.3 martian years). This article discusses the deposition and erosion of thin deposits (ten to hundreds of micrometers) of bright red dust associated with global dust storms, and the removal of centimeter amounts of material in selected areas during a dust storm late in the third winter. Atmospheric pressure data acquired during the period of intense erosion imply that baroclinic disturbances and strong diurnal solar tidal heating combined to produce strong winds. Erosion occurred principally in areas where soil cohesion was reduced by earlier surface sampler activities. Except for redistribution of thin layers of materials, the surface appears to be remarkably stable, perhaps because of cohension of the undisturbed surface material.

Dynamics of intense rainfalls in the southern half of European Russia for the period 1960-2015

NASA Astrophysics Data System (ADS)

Chizhikova, N.

2018-01-01

Two time periods (1960-1986 and 1986-2015) were compared in terms of mean annual frequency and mean annual sum of warm season rainfalls to quantify general trends in the changing regime of heavy precipitation over the southern part of European Russia, which is the area of the most intensive agricultural activity. The identified trends were compared with the published assessment of the intensity trends of soil erosion processes. The prevalence of the increasing tendency in the frequency and amount of precipitation is demonstrated, which undergoes against a decrease in the rate of eroded sediment accumulation and against a decrease of linear growth rate of gullies. This result rather proves the crucial contribution of the snowmelt to the soil erosion over the studied area.

Coastal erosion and wetland change in Louisiana: selected USGS products

USGS Publications Warehouse

Williams, S. Jeffress; Reid, Jamey M.; Cross, VeeAnn A.; Polloni, Christopher F.

2003-01-01

This Digital Data Series (DDS) report is primarily a selection of USGS science products that were previously published as paper atlases and maps but are no longer available in their original form. We have made an attempt to preserve the paper atlases by having them scanned in an efficient compressed digital format that provides a print-on-demand as well as a programmed viewing capability of the original material. We included additional materials bearing on aspects to enhance the scientific understanding of coastal erosion and wetland loss in Louisiana. In addition, this report contains multimedia-based publications including photographs, a 48-minute video, and map tools to allow the user to experience the many scientifically based research activities that are in progress along the coast of Louisiana.

Use of palm-mat geotextiles for rainsplash erosion control

NASA Astrophysics Data System (ADS)

Bhattacharyya, R.; Fullen, M. A.; Davies, K.; Booth, C. A.

2010-07-01

Soil detachment by raindrop action (rainsplash erosion) is a very important subprocess of erosion by water. It is a particular problem in the UK as most soils are sandy or loamy sand in texture and lands have gentle to medium slope. However, few studies report potential rainsplash erosion control options under field conditions. Hence, the utilization of palm-mat geotextiles as a rainsplash erosion control technique was investigated at Hilton, east Shropshire, U.K. (52°33'5.7″ N, 2°19'18.3″ W). Geotextile-mats constructed from Borassus aethiopum (Borassus palm of West Africa) and Mauritia flexuosa (Buriti palm of South America) leaves are termed Borassus mats and Buriti mats, respectively. Two-year field experiments were conducted at Hilton to study the effects of emplacing Borassus and Buriti mats on rainsplash erosion of a loamy sand soil. Two sets (12 plots each) of experiments were established to study the effects of these mats on splash height and splash erosion. Splash height needs to be known to assess the transport mechanism of major soil fraction and its constituents on sloping land by rainsplash. In both sets, six randomly-selected plots were covered with mats, and the rest were bare. Results (during 22/01/2007‒23/01/2009; total precipitation = 1731.5 mm) show that Borassus mat-covered plots had ˜ 89% ( P < 0.001) less total splash erosion (2.97 kg m - 2 ) than bare plots (27.02 kg m - 2 ). Comparatively, mean splash height from Borassus mat-covered plots (0.12 m) was significantly ( P < 0.001) less than the bare plots, by ˜ 54%. However, Buriti mat-cover on bare plots had no significant ( P > 0.05) effect in rainsplash erosion control during that period, although plots with Buriti mats significantly ( P < 0.05) decreased splash height (by ˜ 18%) compared with bare plots (0.26 m). Buriti mats, probably due to their ˜ 43, 62 and 50% lower cover percentage (44%), mass per unit area (413 g - 2 ) and thickness (10 mm), respectively, compared with Borassus mats, were not effective in rainsplash erosion control. Both mats did not significantly ( P > 0.05) improve selected soil properties (i.e., soil organic matter, particle size distribution, aggregate stability and total soil carbon) as soil organic matter (SOM) input from mat-decomposition was much less than total SOM content. However, the changes in fine and medium sand contents (after 2 years) in the Borassus covered plots were significantly ( P < 0.05; n = 6) related to the total rainsplash erosion during 2007‒2009. Emplacement of Borassus and Buriti mats on bare soils did not decrease SOM contents after 2 years, indicating that improvements in some soil properties might occur over longer durations. After ˜ 10 months, Buriti mats lost ˜ 70% of their initial weight ( P < 0.001) and their initial cover percentage ( C, %) decreased drastically ( P < 0.05); whereas, Borassus mats maintained similar C to the initial condition, although mass per unit area decreased by ˜ 20% ( P < 0.05). Moreover, the functional longevity of Borassus mats was ˜ 2 years against only 1 year for Buriti mats. Hence, use of Borassus mats is highly effective for rainsplash erosion control in the UK.

Effects of soil management techniques on soil water erosion in apricot orchards.

PubMed

Keesstra, Saskia; Pereira, Paulo; Novara, Agata; Brevik, Eric C; Azorin-Molina, Cesar; Parras-Alcántara, Luis; Jordán, Antonio; Cerdà, Artemi

2016-05-01

Soil erosion is extreme in Mediterranean orchards due to management impact, high rainfall intensities, steep slopes and erodible parent material. Vall d'Albaida is a traditional fruit production area which, due to the Mediterranean climate and marly soils, produces sweet fruits. However, these highly productive soils are left bare under the prevailing land management and marly soils are vulnerable to soil water erosion when left bare. In this paper we study the impact of different agricultural land management strategies on soil properties (bulk density, soil organic matter, soil moisture), soil water erosion and runoff, by means of simulated rainfall experiments and soil analyses. Three representative land managements (tillage/herbicide/covered with vegetation) were selected, where 20 paired plots (60 plots) were established to determine soil losses and runoff. The simulated rainfall was carried out at 55mmh(-1) in the summer of 2013 (<8% soil moisture) for one hour on 0.25m(2) circular plots. The results showed that vegetation cover, soil moisture and organic matter were significantly higher in covered plots than in tilled and herbicide treated plots. However, runoff coefficient, total runoff, sediment yield and soil erosion were significantly higher in herbicide treated plots compared to the others. Runoff sediment concentration was significantly higher in tilled plots. The lowest values were identified in covered plots. Overall, tillage, but especially herbicide treatment, decreased vegetation cover, soil moisture, soil organic matter, and increased bulk density, runoff coefficient, total runoff, sediment yield and soil erosion. Soil erosion was extremely high in herbicide plots with 0.91Mgha(-1)h(-1) of soil lost; in the tilled fields erosion rates were lower with 0.51Mgha(-1)h(-1). Covered soil showed an erosion rate of 0.02Mgha(-1)h(-1). These results showed that agricultural management influenced water and sediment dynamics and that tillage and herbicide treatment should be avoided. Copyright © 2016 Elsevier B.V. All rights reserved.

Does erosion progress differently on teeth already presenting clinical signs of erosive tooth wear than on sound teeth? An in vitro pilot trial.

PubMed

Carvalho, Thiago Saads; Baumann, Tommy; Lussi, Adrian

2016-07-07

Erosive tooth wear (ETW) is clinically characterized by a loss of tooth surface, and different enamel depths may have different susceptibility to demineralization. Therefore, the aim of this in vitro pilot study was to assess if the progression of erosive demineralization is faster on teeth already presenting signs of ETW when compared to originally sound teeth. We selected 23 central incisors: 14 were clinically sound (Sound) and 9 presented clinical signs of early erosive tooth wear (ETW-teeth). The teeth were embedded in resin, leaving an uncovered window of native enamel (6.69 ± 2.30 mm(2)) on the incisal half of the labial surface. We measured enamel surface reflection intensity (SRI) initially and after each consecutive erosive challenge (1 % citric acid, total of 4, 8, 12, 16, 20 and 24 min). Calcium released to the citric acid was measured with an atomic absorption spectrometer. We observed higher initial SRI values in ETW-teeth than in Sound teeth (p = 0.007). During in vitro erosive demineralization, we observed that erosion on originally Sound teeth progressed significantly slower (p = 0.033) than on ETW-teeth: SRI decreased by 75 % (from 100 to 25 %) on Sound teeth, and by 89 % (from 100 to 11 %) on ETW-teeth. Calcium release increased during erosion, but presented no significant differences (p = 0.643) between originally Sound (0.031 μmol/mm(2)) and ETW-teeth (0.032 μmol/mm(2)). There was satisfactory correlation between calcium release and rSRI values (r s  = -0.66). The optical reflectometer distinguished originally sound teeth from those with signs of ETW, and the results suggest that acid demineralization progresses differently on teeth already presenting clinical signs of ETW than on sound teeth.

Deep erosions of the palmar aspect of the navicular bone diagnosed by standing magnetic resonance imaging.

PubMed

Sherlock, C; Mair, T; Blunden, T

2008-11-01

Erosion of the palmar (flexor) aspect of the navicular bone is difficult to diagnose with conventional imaging techniques. To review the clinical, magnetic resonance (MR) and pathological features of deep erosions of the palmar aspect of the navicular bone. Cases of deep erosions of the palmar aspect of the navicular bone, diagnosed by standing low field MR imaging, were selected. Clinical details, results of diagnostic procedures, MR features and pathological findings were reviewed. Deep erosions of the palmar aspect of the navicular bone were diagnosed in 16 mature horses, 6 of which were bilaterally lame. Sudden onset of lameness was recorded in 63%. Radiography prior to MR imaging showed equivocal changes in 7 horses. The MR features consisted of focal areas of intermediate or high signal intensity on T1-, T2*- and T2-weighted images and STIR images affecting the dorsal aspect of the deep digital flexor tendon, the fibrocartilage of the palmar aspect, subchondral compact bone and medulla of the navicular bone. On follow-up, 7/16 horses (44%) had been subjected to euthanasia and only one was being worked at its previous level. Erosions of the palmar aspect of the navicular bone were confirmed post mortem in 2 horses. Histologically, the lesions were characterised by localised degeneration of fibrocartilage with underlying focal osteonecrosis and fibroplasia. The adjacent deep digital flexor tendon showed fibril formation and fibrocartilaginous metaplasia. Deep erosions of the palmar aspect of the navicular bone are more easily diagnosed by standing low field MR imaging than by conventional radiography. The lesions involve degeneration of the palmar fibrocartilage with underlying osteonecrosis and fibroplasia affecting the subchondral compact bone and medulla, and carry a poor prognosis for return to performance. Diagnosis of shallow erosive lesions of the palmar fibrocartilage may allow therapeutic intervention earlier in the disease process, thereby preventing progression to deep erosive lesions.

Runoff and initial erosion assessment in fruit tree crops and improved forage pastures in the slopes of the Irazu Volcano (Costa Rica)

NASA Astrophysics Data System (ADS)

Marchamalo, Miguel; González-Rodrigo, Beatriz

2017-04-01

Costa Rica is located in the Central American tropical isthmus. It presents high precipitations (ranging from 1400-8500 mm) and protection levels (27% of national territory). However, intensive land use and increasing population in headwaters are major threats for water resource management in this country. Birrís Basin is a 4800 hectares sub-watershed of the River Reventazón Basin, the major hydroelectric source in Costa Rica. Birrís Basin was selected for its high estimated erosion rates and its potential for demonstrative projects (ICE, 1999). Some pilot projects have been developed in this watershed starting from 1999, when major Costa Rican energy producer, Instituto Costarricense de Electricidad, began with a long term watershed management program for the Reventazón Basin. This study aims at measuring runoff and initial splash and sheet erosion to assess the hydrological response of two pilot land use projects. Erosion and runoff plots were established and monitored in a one year period for two pilot projects (fruit trees and forage pastures) and their respective traditional land uses (vegetable crops and extensive pastures). Improved forage pastures showed reduced runoff by 73% and split erosion by 55% compared to prior extensive pastures. Conversion of vegetable crop lands into fruit tree plantations (apricot and avocado) made possible a 97% reduction of soil initial erosion. Land use pilot projects have succeeded in runoff and soil erosion reduction. Now it is time for a wider technology transfer program to expand improved land uses within Birrís Basin.

Evaluation of different machine learning models for predicting and mapping the susceptibility of gully erosion

NASA Astrophysics Data System (ADS)

Rahmati, Omid; Tahmasebipour, Nasser; Haghizadeh, Ali; Pourghasemi, Hamid Reza; Feizizadeh, Bakhtiar

2017-12-01

Gully erosion constitutes a serious problem for land degradation in a wide range of environments. The main objective of this research was to compare the performance of seven state-of-the-art machine learning models (SVM with four kernel types, BP-ANN, RF, and BRT) to model the occurrence of gully erosion in the Kashkan-Poldokhtar Watershed, Iran. In the first step, a gully inventory map consisting of 65 gully polygons was prepared through field surveys. Three different sample data sets (S1, S2, and S3), including both positive and negative cells (70% for training and 30% for validation), were randomly prepared to evaluate the robustness of the models. To model the gully erosion susceptibility, 12 geo-environmental factors were selected as predictors. Finally, the goodness-of-fit and prediction skill of the models were evaluated by different criteria, including efficiency percent, kappa coefficient, and the area under the ROC curves (AUC). In terms of accuracy, the RF, RBF-SVM, BRT, and P-SVM models performed excellently both in the degree of fitting and in predictive performance (AUC values well above 0.9), which resulted in accurate predictions. Therefore, these models can be used in other gully erosion studies, as they are capable of rapidly producing accurate and robust gully erosion susceptibility maps (GESMs) for decision-making and soil and water management practices. Furthermore, it was found that performance of RF and RBF-SVM for modelling gully erosion occurrence is quite stable when the learning and validation samples are changed.

Identifying plant traits: a key aspect for suitable species selection in ecological restoration of semiarid slopes

NASA Astrophysics Data System (ADS)

Bochet, Esther; García-Fayos, Patricio

2017-04-01

In the context of ecological restoration, one of the greatest challenges for practitioners and scientists is to select suitable species for revegetation purposes. In semiarid environments where restoration projects often fail, little attention has been paid so far to the contribution of plant traits to species success. The objective of this study was to (1) identify plant traits associated with species success on four roadside situations along an erosion-productivity gradient, and (2) to provide an ecological framework for selecting suitable species on the basis of their morphological and functional traits, applied to semiarid environments. We analyzed the association of 10 different plant traits with species success of 296 species surveyed on the four roadside situations in a semiarid region (Valencia, Spain). Plant traits included general plant traits (longevity, woodiness) and more specific root-, seed- and leaf-related traits (root type, sprouting ability, seed mucilage, seed mass, seed susceptibility to removal, specific leaf area and leaf dry matter content). All of them were selected according to the prevailing limiting ecogeomorphological processes acting along the erosion-productivity gradient. We observed strong shifts along the erosion-productivity gradient in the traits associated to species success. At the harshest end of the gradient, the most intensely eroded and driest one, species success was mainly associated to seed resistance to removal by runoff and to resistance to drought. At the opposite end of the gradient, the most productive one, species success was associated to a competitive-ruderal plant strategy (herbaceous successful species with high specific leaf area and low leaf dry matter content). Our study provides an ecologically-based approach for selecting suitable native species on the basis or their morphological and functional traits and supports a differential trait-based selection of species as regards roadslope type and aspect. In conclusion, these new insights from basic ecology and practical management guidance represent a great opportunity for practitioners to move forward with the success of roadslope restoration in semiarid environments.

[Estimation of the effect derived from wind erosion of soil and dust emission in Tianjin suburbs on the central district based on WEPS model].

PubMed

Chen, Li; Han, Ting-Ting; Li, Tao; Ji, Ya-Qin; Bai, Zhi-Peng; Wang, Bin

2012-07-01

Due to the lack of a prediction model for current wind erosion in China and the slow development for such models, this study aims to predict the wind erosion of soil and the dust emission and develop a prediction model for wind erosion in Tianjin by investigating the structure, parameter systems and the relationships among the parameter systems of the prediction models for wind erosion in typical areas, using the U.S. wind erosion prediction system (WEPS) as reference. Based on the remote sensing technique and the test data, a parameter system was established for the prediction model of wind erosion and dust emission, and a model was developed that was suitable for the prediction of wind erosion and dust emission in Tianjin. Tianjin was divided into 11 080 blocks with a resolution of 1 x 1 km2, among which 7 778 dust emitting blocks were selected. The parameters of the blocks were localized, including longitude, latitude, elevation and direction, etc.. The database files of blocks were localized, including wind file, climate file, soil file and management file. The weps. run file was edited. Based on Microsoft Visualstudio 2008, secondary development was done using C + + language, and the dust fluxes of 7 778 blocks were estimated, including creep and saltation fluxes, suspension fluxes and PM10 fluxes. Based on the parameters of wind tunnel experiments in Inner Mongolia, the soil measurement data and climate data in suburbs of Tianjin, the wind erosion module, wind erosion fluxes, dust emission release modulus and dust release fluxes were calculated for the four seasons and the whole year in suburbs of Tianjin. In 2009, the total creep and saltation fluxes, suspension fluxes and PM10 fluxes in the suburbs of Tianjin were 2.54 x 10(6) t, 1.25 x 10(7) t and 9.04 x 10(5) t, respectively, among which, the parts pointing to the central district were 5.61 x 10(5) t, 2.89 x 10(6) t and 2.03 x 10(5) t, respectively.

Geo-statistical model of Rainfall erosivity by using high temporal resolution precipitation data in Europe

NASA Astrophysics Data System (ADS)

Panagos, Panos; Ballabio, Cristiano; Borrelli, Pasquale; Meusburger, Katrin; Alewell, Christine

2015-04-01

Rainfall erosivity (R-factor) is among the 6 input factors in estimating soil erosion risk by using the empirical Revised Universal Soil Loss Equation (RUSLE). R-factor is a driving force for soil erosion modelling and potentially can be used in flood risk assessments, landslides susceptibility, post-fire damage assessment, application of agricultural management practices and climate change modelling. The rainfall erosivity is extremely difficult to model at large scale (national, European) due to lack of high temporal resolution precipitation data which cover long-time series. In most cases, R-factor is estimated based on empirical equations which take into account precipitation volume. The Rainfall Erosivity Database on the European Scale (REDES) is the output of an extensive data collection of high resolution precipitation data in the 28 Member States of the European Union plus Switzerland taking place during 2013-2014 in collaboration with national meteorological/environmental services. Due to different temporal resolutions of the data (5, 10, 15, 30, 60 minutes), conversion equations have been applied in order to homogenise the database at 30-minutes interval. The 1,541 stations included in REDES have been interpolated using the Gaussian Process Regression (GPR) model using as covariates the climatic data (monthly precipitation, monthly temperature, wettest/driest month) from WorldClim Database, Digital Elevation Model and latitude/longitude. GPR has been selected among other candidate models (GAM, Regression Kriging) due the best performance both in cross validation (R2=0.63) and in fitting dataset (R2=0.72). The highest uncertainty has been noticed in North-western Scotland, North Sweden and Finland due to limited number of stations in REDES. Also, in highlands such as Alpine arch and Pyrenees the diversity of environmental features forced relatively high uncertainty. The rainfall erosivity map of Europe available at 500m resolution plus the standard error and the erosivity density (Rainfall erosivity per mm of precipitation) are available in the European Soil Data Centre (ESDAC). The highest erosivity has been found in the mediterrean countries (Italy, Western Greece, Spain, Northern Portugal), South Austria, Slovenia, Croatia and Western United Kingdom.

Storms, channel changes, and a sediment budget for an urban-suburban stream, Difficult Run, Virginia, USA

USGS Publications Warehouse

Gellis, Allen C.; Myers, Michael; Noe, Gregory; Hupp, Cliff R.; Shenk, Edward; Myers, Luke

2017-01-01

Determining erosion and deposition rates in urban-suburban settings and how these processes are affected by large storms is important to understanding geomorphic processes in these landscapes. Sediment yields in the suburban and urban Upper Difficult Run are among the highest ever recorded in the Chesapeake Bay watershed, ranging from 161 to 376 Mg/km2/y. Erosion and deposition of streambanks, channel bed, and bars and deposition of floodplains were monitored between 1 March 2010 and 18 January 2013 in Upper Difficult Run, Virginia, USA. We documented the effects of two large storms, Tropical Storm Lee (September 2011), a 100-year event, and Super Storm Sandy (October 2012) a 5-year event, on channel erosion and deposition. Variability in erosion and deposition rates for all geomorphic features, temporally and spatially, are important conclusions of this study. Tropical Storm Lee was an erosive event, where erosion occurred on 82% of all streambanks and where 88% of streambanks that were aggrading before Tropical Storm Lee became erosional. Statistical analysis indicated that drainage area explains linear changes (cm/y) in eroding streambanks and that channel top width explains cross-sectional area changes (cm2/y) in eroding streambanks and floodplain deposition (mm/y). A quasi-sediment budget constructed for the study period using the streambanks, channel bed, channel bars, and floodplain measurements underestimated the measured suspended-sediment load by 61% (2130 Mg/y). Underestimation of the sediment load may be caused by measurement errors and to contributions from upland sediment sources, which were not measured but estimated at 36% of the gross input of sediment. Eroding streambanks contributed 42% of the gross input of sediment and accounted for 70% of the measured suspended-sediment load. Similar to other urban watersheds, the large percentage of impervious area in Difficult Run and direct runoff of precipitation leads to increased streamflow and streambank erosion. This study emphasizes the importance of streambanks in urban-suburban sediment budgets but also suggests that other sediment sources, such as upland sources, which were not measured in this study, can be an important source of sediment.

Combining sediment fingerprinting and a conceptual model for erosion and sediment transfer to explore sediment sources in an Alpine catchment

NASA Astrophysics Data System (ADS)

Costa, A.; Stutenbecker, L.; Anghileri, D.; Bakker, M.; Lane, S. N.; Molnar, P.; Schlunegger, F.

2017-12-01

In Alpine basins, sediment production and transfer is increasingly affected by climate change and human activities, specifically hydropower exploitation. Changes in sediment sources and pathways significantly influence basin management, biodiversity and landscape evolution. We explore the dynamics of sediment sources in a partially glaciated and highly regulated Alpine basin, the Borgne basin, by combining geochemical fingerprinting with the modelling of erosion and sediment transfer. The Borgne basin in southwest Switzerland is composed of three main litho-tectonic units, which we characterised following a tributary-sampling approach from lithologically characteristic sub-basins. We analysed bulk geochemistry using lithium borate fusion coupled with ICP-ES, and we used it to discriminate the three lithologic sources using statistical methods. Finally, we applied a mixing model to estimate the relative contributions of the three sources to the sediment sampled at the outlet. We combine results of the sediment fingerprinting with simulations of a spatially distributed conceptual model for erosion and transport of fine sediment. The model expresses sediment erosion by differentiating the contributions of erosional processes driven by erosive rainfall, snowmelt, and icemelt. Soil erodibility is accounted for as function of land-use and sediment fluxes are linearly convoluted to the outlet by sediment transfer rates for hillslope and river cells, which are a function of sediment connectivity. Sediment connectivity is estimated on the basis of topographic-hydraulic connectivity, flow duration associated with hydropower flow abstraction and permanent storage in hydropower reservoirs. Sediment fingerprinting at the outlet of the Borgne shows a consistent dominance (68-89%) of material derived from the uppermost, highly glaciated reaches, while contributions of the lower part (10-25%) and middle part (1-16%), where rainfall erosion is predominant, are minor. This result is confirmed by the model simulation which shows that, despite the large flow abstraction (about 90%), the upstream reaches contribute the most of the sediments. This study shows how combining geochemical techniques and sediment erosion models provides insight in the dynamics of sediment sources.

The Arctic Coastal Erosion Problem

DOE Office of Scientific and Technical Information (OSTI.GOV)

Frederick, Jennifer M.; Thomas, Matthew Anthony; Bull, Diana L.

Permafrost-dominated coastlines in the Arctic are rapidly disappearing. Arctic coastal erosion rates in the United States have doubled since the middle of the twentieth century and appear to be accelerating. Positive erosion trends have been observed for highly-variable geomorphic conditions across the entire Arctic, suggesting a major (human-timescale) shift in coastal landscape evolution. Unfortunately, irreversible coastal land loss in this region poses a threat to native, industrial, scientific, and military communities. The Arctic coastline is vast, spanning more than 100,000 km across eight nations, ten percent of which is overseen by the United States. Much of area is inaccessible bymore » all-season roads. People and infrastructure, therefore, are commonly located near the coast. The impact of the Arctic coastal erosion problem is widespread. Homes are being lost. Residents are being dispersed and their villages relocated. Shoreline fuel storage and delivery systems are at greater risk. The U.S. Department of Energy (DOE) and Sandia National Laboratories (SNL) operate research facilities along some of the most rapidly eroding sections of coast in the world. The U.S. Department of Defense (DOD) is struggling to fortify coastal radar sites, operated to ensure national sovereignty in the air, against the erosion problem. Rapid alterations to the Arctic coastline are facilitated by oceanographic and geomorphic perturbations associated with climate change. Sea ice extent is declining, sea level is rising, sea water temperature is increasing, and permafrost state is changing. The polar orientation of the Arctic exacerbates the magnitude and rate of the environmental forcings that facilitate coastal land area loss. The fundamental mechanics of these processes are understood; their non-linear combination poses an extreme hazard. Tools to accurately predict Arctic coastal erosion do not exist. To obtain an accurate predictive model, a coupling of the influences of evolving wave dynamics, thermodynamics, and sediment dynamics must be developed. The objective of this document is to present the state-of-the-science and outline the key steps for creation of a framework that will allow for improved prediction of Arctic coastal erosion rates. This is the first step towards the quantification of coastal hazards that will allow for sustainable planning and development of Arctic infrastructure.« less

Linear Stability and Instability Patterns in Ion Bombarded Silicon Surfaces

NASA Astrophysics Data System (ADS)

Madi, Charbel Said

2011-12-01

This thesis is a combined experimental and theoretical study of the fundamental physical mechanisms governing nanoscale surface morphology evolution of Ar + ion bombarded silicon surfaces. I experimentally determined the topographical phase diagram resulting from Ar+ ion irradiation of Si surfaces at room temperature in the linear regime of surface dynamics as we vary the control parameters ion beam energy and incidence angle. At all energies, it is characterized by a diverging wavelength bifurcation from a smooth stable surface to parallel mode ripples (wavevector parallel to the projected ion beam on the surface) as the ion beam incidence angle is varied. At sufficiently high angles theta ≈ 85°, I observed perpendicular mode ripples (wavevector perpendicular to the ion beam). Through real-time Grazing-Incidence Small Angle X-ray Scattering, I have definitively established that ion-induced erosion, which is the consensus predominant cause of pattern formation, is not only of the wrong sign to explain the measured curvature coefficients responsible in driving the surface dynamics, but also is so small in magnitude as to be essentially negligible for pattern formation except possibly at the most grazing angles of incidence where both erosion and redistribution effects converge to zero. That the contribution of ion impact induced prompt atomic redistribution effects entirely overwhelms that of erosion in both the stabilizing and destabilizing regimes is of profound significance, as it overturns the erosion-based paradigm that has dominated the pattern formation field for over two decades. In situ wafer curvature measurements using the Multi-beam Optical Stress Sensor system were performed during amorphization of silicon by normal incidence 250 eV ion irradiation. An average compressive saturation stress built up in the amorphous layer was found to be as large as 1.5 GPa. By assuming the ion-induced amorphization layer to be modeled as a viscoelastic film that is anisotropically stressed by ion beam irradiation, we measure the deformation imparted per ion due to anisotropic deformation to be equal to A =1.15x10-16 cm2/ion. Although compressive stress is being injected into a thin viscoelastic ion-stimulated surface layer, the surface is unconditionally stable to topographic perturbations, corroborating the measured experimental phase diagram.

Spatial and temporal assessment of back-barrier erosion on Cumberland Island National Seashore, Georgia, 2011–2013

USGS Publications Warehouse

Calhoun, Daniel L.; Riley, Jeffrey W.

2016-07-15

Much research has been conducted to better understand erosion and accretion processes for the seaward zones of coastal barrier islands; however, at Cumberland Island National Seashore, Georgia, the greater management concern is the effect that erosion is having on the resources of the island’s western shoreline, or the back barrier. Catastrophic slumping and regular rates of erosion greater than 1 meter per year threaten important habitat, historical and pre-historical resources, and modern infrastructure on the island. Prior research has helped National Park Service (NPS) staff identify the most severe and vulnerable areas, but in order to develop effective management actions, information is needed on what forces and conditions cause erosion. To this end, the U.S. Geological Survey, in cooperation with the NPS, conducted two longitudinal surveys, one each at the beginning and end of the approximately year-long monitoring period from late 2011 to early 2013, along five selected segments of the back barrier of the Cumberland Island National Seashore. Monitoring stations were constructed at four of these locations that had previously been identified as erosional hotspots. The magnitude of erosion at each location was quantified to determine the relative influence of causative agents. Results indicate that erosion is, in general, highly variable within and among these segments of the Cumberland Island National Seashore’s back barrier. Observed erosion ranged from a maximum of 2.5 meters of bluff-line retreat to some areas that exhibited no net erosion over the 1-year study period. In terms of timing of erosion, three of the four sites were primarily affected by punctuated erosional events that were coincident with above-average high tides and elevated wind speeds. The fourth site exhibited steady, low-magnitude retreat throughout the study period. While it is difficult to precisely subscribe certain amounts of erosion to specific agents, this study provides insight into the mode of erosion among sites and the interaction among factors that set up conditions that may be leading to punctuated events.Estimates of sea-level rise were incorporated into the results of this study to project conditions that could be in place by the end of the 21st century. When using the erosion rates observed in this study to extrapolate future shoreline position, results indicate an average retreat (across all monitored locations) of 15 meters by 2050 and approximately 37 meters by 2100.

The success of recent land management efforts to tackle gully erosion in Northern France

NASA Astrophysics Data System (ADS)

Frankl, Amaury; Nyssen, Jan; Salvador, Pierre-Gil

2017-04-01

In the open-field agricultural landscapes of Europe, especially in the topographic-rolling loess-covered regions, soil erosion is an important problem. Here, small headwater catchments hold almost no permanent vegetation, and with few physical obstacles to reduce runoff velocities, runoff concentration along linear landscape elements (plot boundaries) or thalwegs frequently causes ephemeral gullies to occur - the latter reflecting the poor hydrogeomorphic condition of the land- and soilscape. To tackles this, and to remediate negative on- and off-site effects, land management efforts have multiplied over the past decades in many regions. This includes, amongst others measures, the implementation of vegetation barriers (French fascines, Dutch wilgenteendam). In the loess-dominated Aa river basin (640 km2) of northern France, where cropland accounts for 67% of the cover, mainly managed in open-field agro-industrial farming schemes, we investigated the effect of the implementation of vegetation barriers on ephemeral gully erosion dynamics, together with rainfall characteristics and cropland management. This was done from a spatially explicit study at the scale of 500 x 500 m grid cells using a diachronic analysis of historical aerial photographs (period 1947-2012). Fascines, introduced since 2001, were present in ca. 25% of the gully erosion sites. Spatio-temporal gully length variability was mainly driven by cumulative precipitation, and the presence of fascines could not significantly explain trends in decreasing gully lengths. In addition, the impact of fascines on mudflow hazards and on local sediment storage was also analysed. In sum, fascines clearly showed to have a local effect on the storage of sediment, but due to their limited implementation and poor maintenance, they did not decrease the landscape's vulnerability to gully erosion or mudflow hazards. Being increasingly implemented for erosion control in western Europe, this study points at the challenges encountered when managing vast open-field landscapes with vegetation barriers.

Watershed erosion estimated from a high-resolution sediment core reveals a non-stationary frequency-magnitude relationship and importance of seasonal climate drivers

NASA Astrophysics Data System (ADS)

Gavin, D. G.; Colombaroli, D.; Morey, A. E.

2015-12-01

The inclusion of paleo-flood events greatly affects estimates of peak magnitudes (e.g., Q100) in flood-frequency analysis. Likewise, peak events also are associated with certain synoptic climatic patterns that vary on all time scales. Geologic records preserved in lake sediments have the potential to capture the non-stationarity in frequency-magnitude relationships, but few such records preserve a continuous history of event magnitudes. We present a 10-meter 2000-yr record from Upper Squaw Lake, Oregon, that contains finely laminated silt layers that reflect landscape erosion events from the 40 km2 watershed. CT-scans of the core (<1 mm resolution) and a 14C-dated chronology yielded a pseudo-annual time series of erosion magnitudes. The most recent 80 years of the record correlates strongly with annual peak stream discharge and road construction. We examined the frequency-magnitude relationship for the entire pre-road period and show that the seven largest events fall above a strongly linear relationship, suggesting a distinct process (e.g., severe fires or earthquakes) operating at low-frequency to generate large-magnitude events. Expressing the record as cumulative sediment accumulation anomalies showed the importance of the large events in "returning the system" to the long-term mean rate. Applying frequency-magnitude analysis in a moving window showed that the Q100 and Q10 of watershed erosion varied by 1.7 and 1.0 orders of magnitude, respectively. The variations in watershed erosion are weakly correlated with temperature and precipitation reconstructions at the decadal to centennial scale. This suggests that dynamics both internal (i.e., sediment production) and external (i.e., earthquakes) to the system, as well as more stochastic events (i.e., single severe wildfires) can at least partially over-ride external climate forcing of watershed erosion at decadal to centennial time scales.

The success of recent land management efforts to reduce soil erosion in northern France

NASA Astrophysics Data System (ADS)

Frankl, Amaury; Prêtre, Vincent; Nyssen, Jan; Salvador, Pierre-Gil

2018-02-01

Soil erosion is an important problem in open-field agricultural landscapes. With almost no permanent vegetation in small headwater catchments, and with few physical obstacles to reduce runoff velocities, runoff concentration along linear landscape elements (plot boundaries) or thalwegs frequently causes ephemeral gullies to form - the latter reflecting the poor hydrogeomorphic condition of the land- and soilscape. To address this problem, and to remediate negative on- and off-site effects, land management efforts have multiplied over the past decades in many regions. This includes, amongst other measures, the implementation of vegetation barriers called 'fascines'. In the loess-dominated Aa River basin of northern France, where cropland accounts for 67% of the cover, we investigated the effect of fascines on ephemeral gully erosion dynamics, together with rainfall characteristics and cropland management. This was accomplished through a spatially explicit study of 269 sites prone to ephemeral gullying using a diachronic analysis of historical aerial photographs. Between 1947 and 2012, ephemeral gully densities at the scale of the Aa River basin (643 km2) varied between 0.39 and 1.31 m ha- 1 (long-term average of 0.68 m ha- 1 (with local maxima up to 9.35 m ha- 1). Densities are, however, much higher when only considering the most erosion-vulnerable municipalities (long-term average of 2.23-4.30 m ha- 1); those values should be used when comparing results from this study to other reports of ephemeral gully erosion. Fascines were introduced in 2001 and were present in 30% of the gully erosion sites by 2012. Although the presence of fascines has an effect on gully length reduction, spatial and temporal variations in gully length were mainly driven by cumulative precipitation. Measurement of sediment deposition at 29 fascines in 2016 showed that only 47% of the fascines functioned as sediment sinks. They stored on average 1.7 Mg of sediment per winter half-year, corresponding to 0.009 Mg ha- 1. The results suggest that fascines positively impact the landscape's resilience and reduce ephemeral gully erosion rates. The use of vegetation barriers such as fascines are increasingly implemented for erosion control in western Europe, but pose problems for the management of open-field landscapes.

Wind Erosion

NASA Image and Video Library

2015-07-02

Long term winds have etched the surface in Memnonia Sulci. Partial cemented surface materials are easily eroded by the wind, forming linear ridges called yardangs. The multiple direction of yardangs in this VIS image indicate that there were at least two different wind directions in this area. Orbit Number: 59217 Latitude: -8.33112 Longitude: 186.506 Instrument: VIS Captured: 2015-04-20 15:12 http://photojournal.jpl.nasa.gov/catalog/PIA19502

SU-E-T-497: Semi-Automated in Vivo Radiochromic Film Dosimetry Using a Novel Image Processing Algorithm

DOE Office of Scientific and Technical Information (OSTI.GOV)

Reyhan, M; Yue, N

Purpose: To validate an automated image processing algorithm designed to detect the center of radiochromic film used for in vivo film dosimetry against the current gold standard of manual selection. Methods: An image processing algorithm was developed to automatically select the region of interest (ROI) in *.tiff images that contain multiple pieces of radiochromic film (0.5x1.3cm{sup 2}). After a user has linked a calibration file to the processing algorithm and selected a *.tiff file for processing, an ROI is automatically detected for all films by a combination of thresholding and erosion, which removes edges and any additional markings for orientation.more » Calibration is applied to the mean pixel values from the ROIs and a *.tiff image is output displaying the original image with an overlay of the ROIs and the measured doses. Validation of the algorithm was determined by comparing in vivo dose determined using the current gold standard (manually drawn ROIs) versus automated ROIs for n=420 scanned films. Bland-Altman analysis, paired t-test, and linear regression were performed to demonstrate agreement between the processes. Results: The measured doses ranged from 0.2-886.6cGy. Bland-Altman analysis of the two techniques (automatic minus manual) revealed a bias of -0.28cGy and a 95% confidence interval of (5.5cGy,-6.1cGy). These values demonstrate excellent agreement between the two techniques. Paired t-test results showed no statistical differences between the two techniques, p=0.98. Linear regression with a forced zero intercept demonstrated that Automatic=0.997*Manual, with a Pearson correlation coefficient of 0.999. The minimal differences between the two techniques may be explained by the fact that the hand drawn ROIs were not identical to the automatically selected ones. The average processing time was 6.7seconds in Matlab on an IntelCore2Duo processor. Conclusion: An automated image processing algorithm has been developed and validated, which will help minimize user interaction and processing time of radiochromic film used for in vivo dosimetry.« less

Geomorphic, hydrologic, and erosion data for selected reclaimed hillslopes, the Seneca II Mine, Routt County, Colorado, October 1988 - July 1990

USGS Publications Warehouse

Elliott, J.G.

1993-01-01

Geomorphic, hydrologic, and erosion data were collected from five reclaimed hillslopes at the Seneca II mine near Hayden, Colorado. Hillslope surveys were used to determine hillslope lengths, which range from 670 to 1,280 ft, and hillslope gradients, which range from 0.17 to 0.23 ft/ft (17 to 23 percent). Elevations in the study area range from 6,890 to 7,140 feet and hillslope aspect generally is west or south. Mean total vegetation cover ranges from 74 to 91 percent. Total monthly precipitation for December 1988 through May 1990 was computed from daily measurements made with weighing-bucket precipitation gages. Several snowpack measurements were made during 2 winters. Volumetric soil-water content was determined at incremental depths using a neutron probe and in the upper 11.8 in of soil using a time-domain reflectometer. Active and recent soil erosion was indicated by the presence of rills. Rill density (the sum of rill lengths/unit area) was computed at 50-feet intervals along each hillslope study area. Differences in soil-surface elevations between September or October 1989 and June 1990 were determined with an erosion frame and replicate soil-surface surveys at 16 erosion-study plots.

Granitic boulder erosion caused by chaparral wildfire: Implications for cosmogenic radionuclide dating of bedrock surfaces

USGS Publications Warehouse

Kendrick, Katherine J.; Camille Partin,; Graham, Robert C.

2016-01-01

Rock surface erosion by wildfire is significant and widespread but has not been quantified in southern California or for chaparral ecosystems. Quantifying the surface erosion of bedrock outcrops and boulders is critical for determination of age using cosmogenic radionuclide techniques, as even modest surface erosion removes the accumulation of the cosmogenic radionuclides and causes significant underestimate of age. This study documents the effects on three large granitic boulders following the Esperanza Fire of 2006 in southern California. Spalled rock fragments were quantified by measuring the removed rock volume from each measured boulder. Between 7% and 55% of the total surface area of the boulders spalled in this single fire. The volume of spalled material, when normalized across the entire surface area, represents a mean surface lowering of 0.7–12.3 mm. Spalled material was thicker on the flanks of the boulders, and the height of the fire effects significantly exceeded the height of the vegetation prior to the wildfire. Surface erosion of boulders and bedrock outcrops as a result of wildfire spalling results in fresh surfaces that appear unaffected by chemical weathering. Such surfaces may be preferentially selected by researchers for cosmogenic surface dating because of their fresh appearance, leading to an underestimate of age.

Erosion and Soil Contamination Control Using Coconut Flakes And Plantation Of Centella Asiatica And Chrysopogon Zizanioides

NASA Astrophysics Data System (ADS)

Roslan, Rasyikin; Che Omar, Rohayu; Nor Zuliana Baharuddin, Intan; Zulkarnain, M. S.; Hanafiah, M. I. M.

2016-11-01

Land degradation in Malaysia due to water erosion and water logging cause of loss of organic matter, biodiversity and slope instability but also land are contaminated with heavy metals. Various alternative such as physical remediation are use but it not showing the sustainability in term of environmental sustainable. Due to that, erosion and soil contamination control using coconut flakes and plantation of Centella asiatica and Chrysopogon zizanioides are use as alternative approach for aid of sophisticated green technology known as phytoremediation and mycoremediation. Soil from cabonaceous phyllite located near to Equine Park, Sri Kembangan are use for monitoring the effect of phytoremediation and mycoremediation in reducing soil contamination and biotechnology for erosion control. Five laboratory scale prototypes were designed to monitor the effect of different proportion of coconut flakes i.e. 10%, 25%, 50% & 100% and plantation of Centella asiatica and Chrysopogon zizanioides to reduce the top soil from eroding and reduce the soil contamination. Prototype have been observe started from first week and ends after 12 weeks. Centella asiatica planted on 10% coconut flakes with 90% soil and Chrysopogon zizanioides planted on 25% coconut flakes with 75% soil are selected proportion to be used as phytoremediation and mycoremediation in reducing soil contamination and biotechnology for erosion control.

Universal shape evolution of particles by bed-load

NASA Astrophysics Data System (ADS)

Jerolmack, D. J.; Domokos, G.; Shaw, S.; Sipos, A.; Szabo, T.

2016-12-01

River currents, wind and waves drive bed-load transport, in which sediment particles collide with each other and the Earth's surface. A generic consequence is erosion and rounding of particles as a result of chipping, often referred to in geological literature as abrasion. Recent studies have shown that the erosion of river pebbles can be modeled as diffusion of surface curvature, indicating that geometric aspects of chipping erosion are insensitive to details of collisions and material properties. Here we present data from fluvial, aeolian and coastal environments that suggest a universal relation between particle circularity and mass lost due to bed-load chipping. Simulations and experiments support the diffusion model and demonstrate that three constraints are required to produce this universal curve: (i) initial particles are fragments; (ii) erosion is dominated by collisions among like-sized particles; and (iii) collision energy is small enough that chipping dominates over fragmentation. We show that the mechanics of bedrock weathering and bed-load transport select these constraints, providing the foundation to estimate a particle's erosion rate from its shape alone in most sedimentary environments. These findings may be used to determine the contribution of chipping to downstream fining in rivers and deserts, and to infer transport conditions using only images of sediment grains.

Comparative study of soil erodibility and critical shear stress between loess and purple soils

NASA Astrophysics Data System (ADS)

Xing, Hang; Huang, Yu-han; Chen, Xiao-yan; Luo, Bang-lin; Mi, Hong-xing

2018-03-01

Loess and purple soils are two very important cultivated soils, with the former in the loess region and the latter in southern sub-tropical region of China, featured with high-risks of erosion, considerable differences of soil structures due to differences in mineral and nutrient compositions. Study on soil erodibility (Kr) and critical shear stress (τc) of these two soils is beneficial to predict soil erosion with such models as WEPP. In this study, rill erosion experimental data sets of the two soils are used for estimating their Kr and τc before they are compared to understand their differences of rill erosion behaviors. The maximum detachment rates of the loess and purple soils are calculated under different hydrodynamic conditions (flow rates: 2, 4, 8 L/min; slope gradients: 5°, 10°, 15°, 20°, 25°) through analytical and numerical methods respectively. Analytical method used the derivative of the function between sediment concentration and rill length to estimate potential detachment rates, at the rill beginning. Numerical method estimated potential detachment rates with the experimental data, at the rill beginning and 0.5 m location. The Kr and τc of these two soils are determined by the linear equation based on experimental data. Results show that the methods could well estimate the Kr and τc of these two soils as they remain basically unchanged under different hydrodynamic conditions. The Kr value of loess soil is about twice of the purple soil, whereas the τc is about half of that. The numerical results have good correlations with the analytical values. These results can be useful in modeling rill erosion processes of loess and purple soils.

Do root traits affect a plant's ability to influence soil erosion?

NASA Astrophysics Data System (ADS)

Burak, Emma; Quinton, John; Dodd, Ian

2017-04-01

With the ever increasing global population the agricultural sector is put under increasing pressure. This pressure is imposed on the soil and results in wide spread degradation that ultimately decreases productivity. Soil erosion is one of the main features of this degradation. Much focus has been put on the ability of plant canopies to mitigate soil erosion but little research has assessed the impact of below ground biomass. It is understood that woody roots reinforce slopes and lateral roots are believed to support the soil surface but the impact of root hairs is completely unknown. This study used two root hairless mutants one of barley (brb) and one of maize (rth3) along with their wild types (WT) to assess the capacity of different root traits to bind soil particles to the root system, creating a physical coating called a rhizosheath. The two genotypes were grown in a clay loam and periodically harvested during vegetative development. Rhizosheath weight was used to measure the ability of the root system to effectively bind soil particles, while root length was measured to standardise the results between genotypes. Overall, rhizosheath weight increased linearly with root length. When compared to WT plants of the same age, the root length of brb was, on average, 37% greater, suggesting that they compensated for the absence of root hairs by proliferating lateral roots. However, WT plants were far superior at binding soil particles as the rhizosheath weights were 5 fold greater, when expressed per unit root length. Thus root hairs are more important in binding soil particles than lateral roots. Whether these genotypic differences in root traits affect soil erosion will be assessed using mesocosm and field trials. Keywords: Soil erosion, Roots, Barley, Rhizosheath

Erosion and attrition of human enamel in vitro part II: influence of time and loading.

PubMed

Eisenburger, M; Addy, M

2002-01-01

To determine the influence of load and time on enamel wear by attrition under neutral and acid environments in vitro. Groups of 10 enamel cusp and smooth surface specimens obtained from unerupted third molars were opposed in a wear machine under loads of 200, 400 and 600 g in citric acid at pH 3.2 and in physiological saline at 35 degrees C for 30 min (2280 wear cycles). The experiment was repeated with a load of 600 g for 10 and 20 min accompanied by 10 taped specimens to measure erosion only. Erosion and attrition of smooth surface specimens was determined by profilometry. At a load of 600 g attrition in saline increased with time from 7.9 microm (SD 3.7 microm) at 10 min, 10.2 microm (SD 4.8 microm) at 20-25.5 microm (SD 9.1 microm) after 30 min and combined attrition/erosion in citric acid from 1.5 microm (SD 0.4 microm) to 2.5 microm (SD 0.9 microm) to 6.0 microm (SD 3.7 microm). At a fixed time of 30 min, attrition in saline was 5.2 microm (SD 3.6 microm) at 200 g and 8.1 microm (SD 1.5 microm) at 400 g and combined attrition/erosion in citric acid 2.8 microm (SD 1.2 microm) and 3.6 microm (SD 0.7 microm). Comparison between both environments revealed significant differences at fixed load at all time points (p < 0.01) and at fixed time between 400 and 600 g (p < 0.01). Load and time significantly influence enamel wear both in acid and neutral conditions but the effects were not linear. Copyright 2002 Elsevier Science Ltd.

Thermal Conductivity and Erosion Durability of Composite Two-Phase Air Plasma Sprayed Thermal Barrier Coatings

NASA Technical Reports Server (NTRS)

Schmitt, Michael P.; Rai, Amarendra K.; Zhu, Dongming; Dorfman, Mitchell R.; Wolfe, Douglas E.

2015-01-01

To enhance efficiency of gas turbines, new thermal barrier coatings (TBCs) must be designed which improve upon the thermal stability limit of 7 wt% yttria stabilized zirconia (7YSZ), approximately 1200 C. This tenant has led to the development of new TBC materials and microstructures capable of improved high temperature performance. This study focused on increasing the erosion durability of cubic zirconia based TBCs, traditionally less durable than the metastable t' zirconia based TBCs. Composite TBC microstructures composed of a low thermal conductivity/high temperature stable cubic Low-k matrix phase and a durable t' Low-k secondary phase were deposited via APS. Monolithic coatings composed of cubic Low-k and t' Low-k were also deposited, in addition to a 7YSZ benchmark. The thermal conductivity and erosion durability were then measured and it was found that both of the Low-k materials have significantly reduced thermal conductivities, with monolithic t' Low-k and cubic Low-k improving upon 7YSZ by approximately 13 and approximately 25%, respectively. The 40 wt% t' Low-k composite (40 wt% t' Low-k - 60 wt% cubic Low-k) showed a approximately 22% reduction in thermal conductivity over 7YSZ, indicating even at high levels, the t' Low-k secondary phase had a minimal impact on thermal in the composite coating. It was observed that a mere 20 wt% t' Low-k phase addition can reduce the erosion of a cubic Low-k matrix phase composite coating by over 37%. Various mixing rules were then investigated to assess this non-linear composite behavior and suggestions were made to further improve erosion durability.

Compensatory selection for roads over natural linear features by wolves in northern Ontario: Implications for caribou conservation

PubMed Central

Patterson, Brent R.; Anderson, Morgan L.; Rodgers, Arthur R.; Vander Vennen, Lucas M.; Fryxell, John M.

2017-01-01

Woodland caribou (Rangifer tarandus caribou) in Ontario are a threatened species that have experienced a substantial retraction of their historic range. Part of their decline has been attributed to increasing densities of anthropogenic linear features such as trails, roads, railways, and hydro lines. These features have been shown to increase the search efficiency and kill rate of wolves. However, it is unclear whether selection for anthropogenic linear features is additive or compensatory to selection for natural (water) linear features which may also be used for travel. We studied the selection of water and anthropogenic linear features by 52 resident wolves (Canis lupus x lycaon) over four years across three study areas in northern Ontario that varied in degrees of forestry activity and human disturbance. We used Euclidean distance-based resource selection functions (mixed-effects logistic regression) at the seasonal range scale with random coefficients for distance to water linear features, primary/secondary roads/railways, and hydro lines, and tertiary roads to estimate the strength of selection for each linear feature and for several habitat types, while accounting for availability of each feature. Next, we investigated the trade-off between selection for anthropogenic and water linear features. Wolves selected both anthropogenic and water linear features; selection for anthropogenic features was stronger than for water during the rendezvous season. Selection for anthropogenic linear features increased with increasing density of these features on the landscape, while selection for natural linear features declined, indicating compensatory selection of anthropogenic linear features. These results have implications for woodland caribou conservation. Prey encounter rates between wolves and caribou seem to be strongly influenced by increasing linear feature densities. This behavioral mechanism–a compensatory functional response to anthropogenic linear feature density resulting in decreased use of natural travel corridors–has negative consequences for the viability of woodland caribou. PMID:29117234

Compensatory selection for roads over natural linear features by wolves in northern Ontario: Implications for caribou conservation.

PubMed

Newton, Erica J; Patterson, Brent R; Anderson, Morgan L; Rodgers, Arthur R; Vander Vennen, Lucas M; Fryxell, John M

2017-01-01

Woodland caribou (Rangifer tarandus caribou) in Ontario are a threatened species that have experienced a substantial retraction of their historic range. Part of their decline has been attributed to increasing densities of anthropogenic linear features such as trails, roads, railways, and hydro lines. These features have been shown to increase the search efficiency and kill rate of wolves. However, it is unclear whether selection for anthropogenic linear features is additive or compensatory to selection for natural (water) linear features which may also be used for travel. We studied the selection of water and anthropogenic linear features by 52 resident wolves (Canis lupus x lycaon) over four years across three study areas in northern Ontario that varied in degrees of forestry activity and human disturbance. We used Euclidean distance-based resource selection functions (mixed-effects logistic regression) at the seasonal range scale with random coefficients for distance to water linear features, primary/secondary roads/railways, and hydro lines, and tertiary roads to estimate the strength of selection for each linear feature and for several habitat types, while accounting for availability of each feature. Next, we investigated the trade-off between selection for anthropogenic and water linear features. Wolves selected both anthropogenic and water linear features; selection for anthropogenic features was stronger than for water during the rendezvous season. Selection for anthropogenic linear features increased with increasing density of these features on the landscape, while selection for natural linear features declined, indicating compensatory selection of anthropogenic linear features. These results have implications for woodland caribou conservation. Prey encounter rates between wolves and caribou seem to be strongly influenced by increasing linear feature densities. This behavioral mechanism-a compensatory functional response to anthropogenic linear feature density resulting in decreased use of natural travel corridors-has negative consequences for the viability of woodland caribou.

The influence of the annual invasive plant, Impatiens glandulifera, on the sediment dynamics of inland watercourses in temperate regions

NASA Astrophysics Data System (ADS)

Dalvi, Shrutika; Greenwood, Philip

2016-04-01

Impatiens glandulifera (Common English Name - Himalayan Balsam) is a non native annual and highly invasive plant that was introduced into parts of Europe from the Himalaya during the nineteenth century as a colourful adornment to parks and gardens. This Plant colonises areas along the river banks, preferably wet, depositional sites, and displaces natural vegetation. The plant is killed by cold weather. The leaves area of riverbank previously occupied by the plant extremely vulnerable to soil erosion until new plant germinates in the following spring. Research work undertaken in the northwest Switzerland and the soutwestern United Kingdom established s link between accelerated soil erosion caused by Impatiens glandulifera and its detrimental impact on native biodiversity of riparian zone of river catchment area. This study focueses on the potential impact of such erosion on sediment quality. A priory reasoning suggests that the preference of Impatiens glandulifera on young depsotional sites near watercourses affects sediment quality. In this study, the results of a soil quality analysis along Impatiens glandulifera-contaminated river banks is presented. Soil physical and chemical properties are compared to non-affected sites to assess the potential impact of preferential erosion on water quality. In addtiion, soil surface profile (SSP) measuring based on by erosion pins, a micro profile bridge and a digital calliper at different selected locations along the riparian zone of river catchment area is used to determine erosion rates and determine sediment transfer from the riparian zone into the rivers.

Effect of Potato (Solanum tuberosum L.) Cropping Systems on Soil and Nutrient Losses Through Runoff in a Humic Nitisol, Kenya

NASA Astrophysics Data System (ADS)

Nyawade, Shadrack; Charles, Gachene; Karanja, Nancy; Elmar, Schulte-Geldermann

2016-04-01

Soil erosion has been identified as one of the major causes of soil productivity decline in the potato growing areas of East African Highlands. Potato establishes a protective soil cover only at about 45-60 days after planting and does not yield sufficient surface mulch upon harvest which leaves the soil bare at the critical times when rainfall intensities are usually high thus exposes soil to erosion. A field study was carried out using runoff plots during the short and long rainy seasons of 2014/15 respectively at the University of Nairobi Upper Kabete Farm, Kenya. The objectives were to assess the effect of soil surface roughness and potato cropping systems on soil loss and runoff, to determine the effect of erosion on nutrient enrichment ratio and to evaluate the soil organic matter fraction most susceptible to soil erosion. The treatments comprised of Bare Soil (T1); Potato + Garden Pea (Pisum sativa) (T2); Potato + Climbing Bean (Phaseolus vulgaris) (T3); Potato + Dolichos (Lablab purpureus) (T4) and Sole Potato (Solanum tuberosum L.) (T5). The amount of soil loss and runoff recorded in each event differed significantly between treatments (p<0.05) and were consistently highest in T1 and lowest in T4. Mean cumulative soil loss reduced by 6.4, 13.3 and 24.4 t ha-1from T2, T3 and T4 respectively compared to sole potato plots (T5), while mean cumulative runoff reduced by 8.5, 17.1 and 28.3 mm from T2, T3 and T4 respectively when compared with the sole potato plots (T5) indicating that T4 plots provided the most effective cover in reducing soil loss and runoff. Regression analyses revealed that both runoff and soil loss related significantly with surface roughness and percent cover (R2=0.83 and 0.73 respectively, p<0.05). Statistically significant linear dependence of runoff and soil loss on surface roughness and crop cover was found in T4 (p<0.05) indicating that this system was highly effective in minimizing soil loss and runoff. Enrichment ratio was on average greater than unity for all soil elements analyzed indicating that erosion process was selective. Concentrations of soil organic matter in the eroded sediment were higher in the stable fraction; mineral organic carbon (18.43-19.30 g kg-1), mineral nitrogen (1.67-1.93 g kg-1) than in the labile fraction; particulate organic carbon (7.72-9.39 g kg-1), particulate nitrogen (0.62-0.84 g kg-1) indicating that much of the eroded soil organic matter was in stable form. The study shows that there is need to incorporate suitable indeterminate legume cover crops such as Dolichos lablab in potato cropping systems so as to minimize soil and nutrient losses due to erosion. Acknowledgement This study was part of the CIP-Sub Saharan Africa managed project-"Improved Soil Fertility Management for Sustainable Intensification in Potato Based Systems in Ethiopia and Kenya"-funded by the BMZ/GIZ International Agricultural Research for Development Fund.

Maintenance practices for stormwater runoff - phase 2.

DOT National Transportation Integrated Search

2015-04-01

Seven wet detention ponds possessing severe maintenance issues were selected from disparate FDOT : districts. The maintenance problems ranged from excess littoral zone growth and intense algal blooms : to bank erosion and sediment accumulation. Inten...

Exploring Water Pollution. Part 3

ERIC Educational Resources Information Center

Rillo, Thomas J.

1976-01-01

Lists over 30 outdoor science activities dealing with water formation, erosion, pollution, and other water-related topics. Provides, in addition, a selected bibliography of films, tapes, booklets and pamphlets, and filmstrips as additional reference materials. (CP)

The role of electronic mechanisms in surface erosion and glow phenomena

NASA Technical Reports Server (NTRS)

Haglund, Richard F., Jr.

1987-01-01

Experimental studies of desorption induced by electronic transitions (DIET) are described. Such studies are producing an increasingly complete picture of the dynamical pathways through which incident electronic energy is absorbed and rechanneled to produce macroscopic erosion and glow. These mechanistic studies can determine rate constants for erosion and glow processes in model materials and provide valuable guidance in materials selection and development. Extensive experiments with electron, photon, and heavy particle irradiation of alkali halides and other simple model materials have produced evidence showing that: (1) surface erosion, consisting primarily in the ejection or desorption of ground-state neutral atoms, occurs with large efficiencies for all irradiated species; (2) surface glow, resulting from the radiative decay of desorbed atoms, likewise occurs for all irradiating species; (3) the typical mechanism for ground-state neutral desorption is exciton formation, followed by relaxation to a permanent, mobile electronic defect which is the precursor to bond-breaking in the surface or near-surface bulk of the material; and (4) the mechanisms for excited atom formation may include curve crossing in atomic collisions, interactions with surface defect or impurity states, or defect diffusion.

Dental erosion among children aged 3-6 years and its associated indicators.

PubMed

Tao, Dan-Ying; Hao, Gu; Lu, Hai-Xia; Tian, Yu; Feng, Xi-Ping

2015-01-01

To analyze the status quo of dental erosion in 3- to 6-year-old children in Shanghai. A stratified, cluster, multistage random sampling methods was applied to 3- to 6-year-old children in Shanghai in 2012. Both questionnaire and clinical oral examination were performed in the survey. The questionnaire included general information, such as age, gender, parental education, dietary habit, oral health behavior, general medical health, and socioeconomic status. The clinical examination focused on the eroded tooth surface and dental erosion extent. SPSS v19.0 software package was utilized for statistical analysis. A total of 1,837 children aged 3-6 years were randomly selected in Shanghai. The overall dental erosion prevalence was 15.1 percent. Among different age groups, a relatively high prevalence of 17.1 percent was found in the 4-year-old group, and a relatively low prevalence of 12.0 percent was observed in the 3-year-old group. Surprisingly, there was no significant difference among the four age groups. The occurrence of dental erosion was influenced by habits of vinegar/coffee/tea consumption, mother's educational background, birthplace, and regurgitation (P < 0.05). The dental erosion prevalence in 3- to 6-year-old children in Shanghai appears to be close to that of other Chinese provinces as well as that observed in most of surveys carried out in different parts of the world. Efforts should be made to raise public awareness about the disease. Moreover, further studies targeted to explore the relationship between dental erosion and risk factors are needed. It is also necessary to establish a unified diagnostic standard for future epidemiological investigations. © 2015 American Association of Public Health Dentistry.

Application of a modeling approach to designate soil and soil organic carbon loss to wind erosion on long-term monitoring sites (BDF) in Northern Germany

NASA Astrophysics Data System (ADS)

Nerger, Rainer; Funk, Roger; Cordsen, Eckhard; Fohrer, Nicola

2017-04-01

Soil organic carbon (SOC) loss is a serious problem in maize monoculture areas of Northern Germany. Sites of the soil monitoring network (SMN) "Boden-Dauerbeobachtung" show long-term soil and SOC losses, which cannot be explained by conventional SOC balances nor by other non-Aeolian causes. Using a process-based model, the main objective was to determine whether these losses can be explained by wind erosion. In the long-term context of 10 years, wind erosion was not measured directly but often observed. A suitable estimation approach linked high-quality soil/farming monitoring data with wind erosion modeling results. The model SWEEP, validated for German sandy soils, was selected using 10-minute wind speed data. Two similar local SMN study sites were compared, however, site A was characterized by high SOC loss and often affected by wind erosion, while the reference site B was not. At site A soil mass and SOC stock decreased by 49.4 and 2.44 kg m-2 from 1999 to 2009. Using SWEEP, a total soil loss of 48.9 kg m-2 resulted for 16 erosion events (max. single event 12.6 kg m-2). A share of 78% was transported by suspension with a SOC enrichment ratio (ER) of 2.96 (saltation ER 0.98), comparable to the literature. At the reference site measured and modeled topsoil losses were minimal. The good agreement between monitoring and modeling results suggested that wind erosion caused significant long-term soil and SOC losses. The approach uses results of prior studies and is applicable to similar well-studied sites without other noteworthy SOC losses.

Meta-analysis of the prevalence of tooth wear in primary dentition.

PubMed

Corica, A; Caprioglio, A

2014-12-01

To conduct a meta-analysis of all the studies published in literature over the past three decades on the prevalence of dental erosion in preschool children. The Pubmed data base revealed only one systematic review on the prevalence of tooth wear in children up to 5 years old. The search included works published from January 1982 to September 2012, using the following combinations of keywords: 1) "dental erosion" AND "children"; 2) "dental erosion in primary dentition"; 3) "dental" AND "attrition" AND "prevalence". The inclusion criteria for papers on tooth wear were the deciduous dentition observed only on the palatal and buccal sides with the distinction of erosion, attrition and abrasion. We took into consideration only randomized control trials. We excluded articles not written in English, case reports, historical and forensic studies, in vitro and in vivo studies. In case of doubt and/or when an abstract was not available, the full text copy of the article was examined. The first search on Pubmed revealed 29 articles, the same found in the study of Kreulen [2010], however we selected only multicentric studies focused on children of age below 5 years old, in which only the primary dentition (D) and only anterior teeth (incisors) were considered. Both forest plot and scatter plot showed the prevalence of dental erosion in primary dentition, and that older children had a more severe dental erosion. Dental erosion should be considered a paediatric dentistry pathological entity as well as dental caries, and it can be related to more severe systemic diseases such as Gastroesophageal reflux disease. In addition, taking care of these little patients is important because they might suffer persentiveness, and also pulpal pathology caused by the typical structure of deciduous teeth, where the pulp cavity is wide and close to the dentine and the enamel.

Comparison of SWAT and GeoWEPP model in predicting the impact of stone bunds on runoff and erosion processes in the Northern Ethiopian Highlands

NASA Astrophysics Data System (ADS)

Demelash, Nigus; Flagler, Jared; Renschler, Chris; Strohmeier, Stefan; Holzmann, Hubert; Feras, Ziadat; Addis, Hailu; Zucca, Claudio; Bayu, Wondimu; Klik, Andreas

2017-04-01

Soil degradation is a major issue in the Ethiopian highlands which are most suitable for agriculture and, therefore, support a major part of human population and livestock. Heavy rainstorms during the rainy season in summer create soil erosion and runoff processes which affect soil fertility and food security. In the last years programs for soil conservation and afforestation were initiated by the Ethiopian government to reduce erosion risk, retain water in the landscape and improve crop yields. The study was done in two adjacent watersheds in the Northwestern highlands of Ethiopia. One of the watersheds is developed by soil and water conservation structures (stone bunds) in 2011 and the other one is without soil and water conservation structures. Spatial distribution of soil textures and other soil properties were determined in the field and in the laboratory and a soil map was derived. A land use map was evaluated based on satellite images and ground truth data. A Digital Elevation Model of the watershed was developed based on conventional terrestrial surveying using a total station. At the outlet of the watersheds weirs with cameras were installed to measure surface runoff. During each event runoff samples were collected and sediment concentration was analyzed. The objective of this study is 1) to assess the impact of stone bunds on runoff and erosion processes by using simulation models, and 2) to compare the performance of two soil erosion models in predicting the measurements. The selected erosion models were the Soil and Water Assessment Tool (SWAT) and the Geospatial Interface to the Water Erosion Prediction Project (GeoWEPP). The simulation models were calibrated/verified for the 2011-2013 periods and validated with 2014-2015 data. Results of this comparison will be presented.

Effect of mismanagement at the state of organic matter in soil

NASA Astrophysics Data System (ADS)

Hladký, Jan; Elbl, Jakub; Kynický, Jindřich; Dvořáčková, Helena; Juřička, David; Pecina, Václav; Brtnický, Martin

2017-04-01

Organic matter is an essential part of the soil. It affects the physical, chemical, and biological properties of the soil. It is therefore necessary to maintain organic matter in the soil and its quality as the prevention of soil degradation. Loss of organic matter is in the Czech Republic threatened up to 45% of arable soil. The most important reason for the loss of organic matter in the soil is poor management, especially improper crop rotation, cultivation of erosion-prone crops where erosion takes away valuable topsoil with nutrients and organic matter. The aim of our study was to verify the influence of inappropriate management on selected 5 plots in southern Moravia in the Czech Republic. It is the region with the highest incidence of water erosion in the Czech Republic. Were selected plots with significantly sloping, where corn was grown. Samples were taken in the autumn after the harvest, each of topsoil. The sampling sites were placed in positions on the slope where soil was not damaged by erosion, as well as the place greatest damage and the place where washed soil was accumulated. Soil average humus content was for undamaged position on the slope 1.93% and 0.84 quality, the most heavily damaged part of the slope humus content dropped to 1.35% and its quality at only 0.56. In the case of position of accumulated soils was found the average amount of humus 1.70% and 0.90 quality. Humus content and its quality is statistically significantly influenced by water erosion (α = 0.05). The study showed that bad management, when there is not crop rotation adapted to the given conditions and not subjected to any suitable soil-protecting technologies, there is significant damage to soils, which shows mainly organic matter decline and a decline in its quality. Continuation of our study will verify the possibility of stabilization of soil organic matter and draft appropriate technologies.

Automated method for measuring the extent of selective logging damage with airborne LiDAR data

NASA Astrophysics Data System (ADS)

Melendy, L.; Hagen, S. C.; Sullivan, F. B.; Pearson, T. R. H.; Walker, S. M.; Ellis, P.; Kustiyo; Sambodo, Ari Katmoko; Roswintiarti, O.; Hanson, M. A.; Klassen, A. W.; Palace, M. W.; Braswell, B. H.; Delgado, G. M.

2018-05-01

Selective logging has an impact on the global carbon cycle, as well as on the forest micro-climate, and longer-term changes in erosion, soil and nutrient cycling, and fire susceptibility. Our ability to quantify these impacts is dependent on methods and tools that accurately identify the extent and features of logging activity. LiDAR-based measurements of these features offers significant promise. Here, we present a set of algorithms for automated detection and mapping of critical features associated with logging - roads/decks, skid trails, and gaps - using commercial airborne LiDAR data as input. The automated algorithm was applied to commercial LiDAR data collected over two logging concessions in Kalimantan, Indonesia in 2014. The algorithm results were compared to measurements of the logging features collected in the field soon after logging was complete. The automated algorithm-mapped road/deck and skid trail features match closely with features measured in the field, with agreement levels ranging from 69% to 99% when adjusting for GPS location error. The algorithm performed most poorly with gaps, which, by their nature, are variable due to the unpredictable impact of tree fall versus the linear and regular features directly created by mechanical means. Overall, the automated algorithm performs well and offers significant promise as a generalizable tool useful to efficiently and accurately capture the effects of selective logging, including the potential to distinguish reduced impact logging from conventional logging.

Passive monitoring of a sea dike during a tidal cycle using sea waves as a seismic noise source

NASA Astrophysics Data System (ADS)

Joubert, Anaëlle; Feuvre, Mathieu Le; Cote, Philippe

2018-05-01

Over the past decade, ambient seismic noise has been used successfully to monitor various geological objects with high accuracy. Recently, it has been shown that surface seismic waves propagating within a sea dike body can be retrieved from the cross-correlation of ambient seismic noise generated by sea waves. We use sea wave impacts to monitor the response of a sea dike during a tidal cycle using empirical Green's functions. These are obtained either by cross-correlation or deconvolution, from signals recorded by sensors installed linearly on the crest of a dike. Our analysis is based on delay and spectral amplitude measurements performed on reconstructed surface waves propagating along the array. We show that localized variations of velocity and attenuation are correlated with changes in water level as a probable consequence of water infiltration inside the structure. Sea dike monitoring is of critical importance for safety and economic reasons, as internal erosion is generally only detected at late stages by visual observations. The method proposed here may provide a solution for detecting structural weaknesses, monitoring progressive internal erosion, and delineating areas of interest for further geotechnical studies, in view to understanding the erosion mechanisms involved.

Applicability of Different Hydraulic Parameters to Describe Soil Detachment in Eroding Rills

PubMed Central

Wirtz, Stefan; Seeger, Manuel; Zell, Andreas; Wagner, Christian; Wagner, Jean-Frank; Ries, Johannes B.

2013-01-01

This study presents the comparison of experimental results with assumptions used in numerical models. The aim of the field experiments is to test the linear relationship between different hydraulic parameters and soil detachment. For example correlations between shear stress, unit length shear force, stream power, unit stream power and effective stream power and the detachment rate does not reveal a single parameter which consistently displays the best correlation. More importantly, the best fit does not only vary from one experiment to another, but even between distinct measurement points. Different processes in rill erosion are responsible for the changing correlations. However, not all these procedures are considered in soil erosion models. Hence, hydraulic parameters alone are not sufficient to predict detachment rates. They predict the fluvial incising in the rill's bottom, but the main sediment sources are not considered sufficiently in its equations. The results of this study show that there is still a lack of understanding of the physical processes underlying soil erosion. Exerted forces, soil stability and its expression, the abstraction of the detachment and transport processes in shallow flowing water remain still subject of unclear description and dependence. PMID:23717669

The role of vegetation on gully erosion stabilization at a severely degraded landscape: A case study from Calhoun Experimental Critical Zone Observatory

NASA Astrophysics Data System (ADS)

Bastola, S.; Dialynas, Y. G.; Bras, R. L.; Noto, L. V.; Istanbulluoglu, E.

2018-05-01

Gully erosion was evidence of land degradation in the southern Piedmont, site of the Calhoun Critical Zone Observatory (CCZO), during the cotton farming era. Understanding of the underlying gully erosion processes is essential to develop gully erosion models that could be useful in assessing the effectiveness of remedial and soil erosion control measures such as gully backfilling, revegetation, and terracing. Development and validation of process-based gully erosion models is difficult because observations of the formation and progression of gullies are limited. In this study, analytic formulations of the two dominant gullying processes, namely, plunge pool erosion and slab failure, are utilized to simulate the gullying processes in the 4-km2 Holcombe's Branch watershed. In order to calibrate parameters of the gully erosion model, gully features (e.g., depth and area) extracted from a high-resolution LiDAR map are used. After the calibration, the gully model is able to delineate the spatial extent of gullies whose statistics are in close agreement with the gullies extracted from the LiDAR DEM. Several simulations with the calibrated model are explored to evaluate the effectiveness of various gully remedial measures, such as backfilling and revegetation. The results show that in the short-term, the reshaping of the topographical surface by backfilling and compacting gullies is effective in slowing down the growth of gullies (e.g., backfilling decreased the spatial extent of gullies by 21-46% and decreased the average depth of gullies by up to 9%). Revegetation, however, is a more effective approach to stabilizing gullies that would otherwise expand if no gully remedial measures are implemented. Analyses of our simulations show that the gully stabilization effect of revegetation varies over a wide range, i.e., leading to 23-69% reduction of the spatial extent of gullies and up to 45% reduction in the depth of gullies, depending on the selection of plant species and management practices.

Application of Unmanned Aerial System-based Photogrammetry to Monitor Landforms Evolution of Mudstone Badlands

NASA Astrophysics Data System (ADS)

Chen, Yichin

2017-04-01

Mudstone badlands are the area characteristized by its rapid erosion and steep, fractured, and barren landforms. Monitoring the topography changes in badland help improve our knowledge of the hillslope and river processing on landforms and develop susceptibility model for surface erosion hazards. Recently, advances in unmanned aerial system (UAS) and close-range photogrammetry technology have opened up the possibility of effectively measuring topography changes with high spatiotemporal resolutions. In this study, we used the UAS and close-range photogrammetry technology to monitor the topography changes in a rapidly eroded badland, south-western Taiwan. A small mudstone hillslope with area of 0.2 ha approximately and with slope gradient of 37 degrees was selected as the study site. A widely used and commercial quadcopter equipped non-metric camera was used to take images with ground sampling distance (GSD) 5 mm approximately. The Pix4DMapper, a commercial close-range photogrammetry software, was used to perform stereo matching, extract point clouds, generate digital surface models (DSMs) and orthoimage. To control model accuracy, a set of ground control points was surveyed by using eGPS. The monitoring was carried out after every significant rainfall event that may induced observable erosion in the badland site. The results show that DSMs have the GSDs of 4.0 5.4 mm and vertical accuracy of 61 116 mm. The accuracy largely depends on the quality of ground control points. The spatial averaged erosion rate during six months of monitoring was 328 mm, which is higher in the gully sides than in the ridges. The erosion rate is positively correlated with the slope gradient and drainage contributing area that implies the important role of surface gully erosion in mudstone badland erosion. This study shows that UAS and close-range photogrammetry technology can be used to monitor the topography change in badland areas effectively and can provide high spatiotemporal resolutions of DSMs for developing distributed surface erosion models.

Is research on soil erosion hazard and mitigation in the Global South still needed? (Alexander von Humbold Medal Lecture)

NASA Astrophysics Data System (ADS)

Poesen, Jean

2016-04-01

Soil erosion represents a geomorphological and geological hazard that may cause environmental damage (land degradation), property damage, loss of livelihoods and services as well as social and economic disruption. Erosion not only lowers the quality of our soils on site, resulting in a drastic reduction of their ecosystem functions that play a vital role in daily life, but causes also significant sediment-related problems off site. To curb soil erosion problems, a range of soil conservation techniques and strategies have been designed and are being applied. Worldwide, ca. 62 000 research papers on soil erosion and 116 000 on soil conservation have been published (Web of Science, Dec. 2015). The number of such papers dealing with the Global South represents less than 20 % of all papers, despite the fact that many regions in this part of the world face significant soil erosion problems, aggravated by a rapidly growing population and major environmental changes. Given the large number of research papers on this topic, one might therefore conclude that we now know almost everything about the various soil erosion processes and rates, their factors and consequences as well as their control so that little new knowledge can still be added to the vast amount of available information. We refute this conclusion by pointing to some major research gaps that still need to be addressed if we want to use our soils in a more sustainable way. More specifically the following topics need more research attention: 1) improved understanding of both natural and anthropogenic soil erosion processes and their interactions, 2) scaling up soil erosion processes and rates in space and time, and 3) innovative techniques and strategies to prevent or reduce erosion rates. This will be illustrated with case studies from the Global South. If future research focuses on these research gaps, we will 1) better understand processes and their interactions operating at a range of spatial and temporal scales, their rates as well as their on-site and off-site impacts, which is crucial for better targeting erosion control measures and which is academically spoken rewarding, and 2) we will also be in a better position to select the most appropriate and effective soil erosion control techniques and strategies which are badly needed for a sustainable use of our soils in the Anthropocene and for the improvement of environmental conditions worldwide.

Hysteretic sediment fluxes in rainfall-driven soil erosion

NASA Astrophysics Data System (ADS)

Cheraghi, Mohsen; Jomaa, Seifeddine; Sander, Graham C.; Barry, D. Andrew

2017-04-01

Hysteresis patterns of different sediment particle sizes were studied via a detailed laboratory study and modelling. Seven continuous rainfall events with stepwise- varying rainfall intensities (30, 37.5, 45, 60, 45, 37.5 and 30 mm h-1, each 20 min duration) were conducted using a 5-m × 2-m erosion flume. Flow rates and sediment concentration data were measured using flume discharge samples, and interpreted using the Hairsine and Rose (HR) soil erosion model. The total sediment concentration and concentrations of seven particle size classes (< 2, 2-20, 20-50, 50-100, 100-315, 315-1000 and > 1000 μm) were measured. For the total eroded soil and the finer particle sizes (< 2, 2-20 and 20-50 μm), there was a clockwise pattern in the sediment concentration versus discharge curves. However, as the particle size increased, concentrations tended to vary linearly with discharge. The HR model predictions for the total eroded soil and the finer particle size classes (up to 100 μm) were in good agreement with the experimental results. For the larger particles, the model provided qualitative agreement with the measurements but concentration values were different. In agreement with previous investigations using the HR model, these differences were attributed to the HR model's assumption of suspended sediment flow, which does not account for saltation and rolling motions. Keywords: Hysteresis effects, Sediment transport, Flume experiment, Splash soil erosion, Hairsine and Rose model, Particle Swarm Optimization.

Soil erosion measurements under organic and conventional land use treatments and different tillage systems using micro-scale runoff plots and a portable rainfall simulator

NASA Astrophysics Data System (ADS)

Seitz, Steffen; Goebes, Philipp; Song, Zhengshan; Wittwer, Raphaël; van der Heijden, Marcel; Scholten, Thomas

2015-04-01

Soil erosion is a major environmental problem of our time and negatively affects soil organic matter (SOM), aggregate stability or nutrient availability for instance. It is well known that agricultural practices have a severe influence on soil erosion by water. Several long-term field trials show that the use of low input strategies (e.g. organic farming) instead of conventional high-input farming systems leads to considerable changes of soil characteristics. Organic farming relies on crop rotation, absence of agrochemicals, green manure and weed control without herbicides. As a consequence, SOM content in the top soil layer is usually higher than on arable land under conventional use. Furthermore, the soil surface is better protected against particle detachment and overland flow due to a continuous vegetation cover and a well-developed root system increases soil stability. Likewise, tillage itself can cause soil erosion on arable land. In this respect, conservation and reduced tillage systems like No-Till or Ridge-Till provide a protecting cover from the previous year's residue and reduce soil disturbance. Many studies have been carried out on the effect of farming practices on soil erosion, but with contrasting results. To our knowledge, most of those studies rely on soil erosion models to calculate soil erosion rates and replicated experimental field measurement designs are rarely used. In this study, we performed direct field assessment on a farming system trial in Rümlang, Switzerland (FAST: Farming System and Tillage experiment Agroscope) to investigate the effect of organic farming practises and tillage systems on soil erosion. A portable single nozzle rainfall simulator and a light weight tent have been used with micro-scale runoff plots (0.4 m x 0.4 m). Four treatments (Conventional/Tillage, Conventional/No-Tillage, Organic/Tillage, Organic/Reduced-tillage) have been sampled with 8 replications each for a total of 32 runoff plots. All plots have been distributed randomly within the treatments. Linear mixed effect modelling was used to examine the effects of the treatments on sediment discharge and surface runoff. Results were compared with recent findings from erosion models and laboratory studies. Results show that sediment discharge is significantly higher (59 %, p=0.018) on conventional treatments (31.8 g/m2/h) than on organic treatments (20.0 g/m2/h). This finding supports results from several studies, which found soil erosion rates from 18 % to 184 % higher on conventional than on organic treatments. Under both farming systems, ploughed treatments show higher sediment discharge (conventional farming: 104 %, organic farming: 133 %, p=0.004) than treatments with reduced or no tillage. Runoff volume did not show significant effects in our treatments. An interaction between the farming practice and the tillage system could not be found, which strengthens the importance of both. With the help of a well-replicated micro-scale runoff plot design and a portable rainfall simulator we were able to gather reliable soil erosion data in situ in short term and without external parameterization. Our field assessment shows that organic farming and reduced tillage practices protect agricultural land best against soil erosion.

Choosing the target of adaptive soil erosion management in Mediterranean. Long vs. Extreme erosion, internal vs. external catchment dynamics

NASA Astrophysics Data System (ADS)

Smetanova, Anna; Follain, Stéphane; David, Mélodie; Ciampalini, Rossano; Raclot, Damien; Crabit, Armand; Le Bissonnais, Yves

2017-04-01

For soil resources protection and regulation of soil erosion off-site effects in Mediterranean, it is inevitable to adjust current land management planning to both, event magnitude and long-term erosion means [2, 3, 5]. Science-based soil protection measures need to be adjusted to spatial and temporal scale of practice differing between stakeholders and management aims, and reflect increasing frequency of torrential rainfalls leading to very high erosion rates in short time [3, 4]. In order to address selection of zero-soil erosion land management target, this study applies modelling approach for comparison of 7 land use scenarios using the LandSoil model [1]. We propose comparison of internal vs. external catchment dynamic at extreme event- and long-term scale as a tool for understanding effect of land management in targeting emerging erosion and connectivity patterns. Our results suggest, that proposed approach can be applied to identify best management scenario practices regarding different management aims of farmers and watershed managers. [1] Ciampalini R, Follain S, Le Bissonnais Y. 2012. LandSoil: A model for analysing the impact of erosion on agricultural landscape evolution. Geomorphology 175-176: 25-37. [2] David M, Follain S, Ciampalini R, Le Bissonnais Y, Couturier A, Walter C. 2014. Simulation of medium-term soil redistributions for different land use and landscape design scenarios within a vineyard landscape in Mediterranean France. Geomorphology 214: 10-21. [3] Smetanová A, Le Bissonnais Y, Raclot D, Nunes JP, Licciardello F, Le Bouteiller C, Latron J, Rodríguez-Caballero E, Mathys N, Klotz S, Mekki I, Gallart F, Solé Benet A, Pérez Gallego N, Andrieux P, Moussa R, Planchon O, Marisa Santos J, Alshihabi O, Chikhaoui M., submitted. Patterns of temporal variability and time compression of sediment yield in small Mediterranean catchments. Soil Use & Management [4] Smetanová A, Paton E, Maynard C, Tindale S, Fernandez-Getino A-P, Marques MJ, Bracken L, Le Bissonnais Y, Keesstra S. submitted -b. Stakeholders' perception of the relevance of water and sediment connectivity in water and land management. Land Degradation & Development [5] Stroosnijder L. 2005. Measurement of erosion: Is it possible? CATENA 64: 162-173.

Basal erosion: barrier to earthquake propagation? Insight from the northern chilean forearc

NASA Astrophysics Data System (ADS)

Cubas, N.

2017-12-01

Subducted topographic features have often been suspected as barriers to large earthquake propagation. These features would induce basal erosion, leading to a large network of fractures impeding large nucleation or shear localization. Looking for correlation between basal erosion and megathrust ruptures is thus critical nowadays to understand earthquake mechanics and infer rupture scenarios. In this study, we propose to seek possible location of basal erosion from the forearc morphology by applying the critical taper theory. We focus on the North Chile subduction zone that has experienced four major earthquakes during the last two decades and where basal erosion and seamount subduction have already been suspected. Basal erosion should occur when the basal friction approaches the internal friction. We thus seek what part of the forearc is at critical state and select areas for which the two frictions are almost equal. We find a large band, located at 25km depth, from the Mejillones peninsula to the Iquique region at critical state with very high basal friction. The critical areas seem to surround the Tocopilla 2007 Mw 7.7 and the Iquique 2014 Mw 8.1 ruptures. When compared with the interseismic coupling, except for the Tocopilla segment, the critical areas are located in low-coupled zones. More interestingly, the reported normal faults of the forearc do not appear above the erosional areas but rather between them. These normal faults are systematically located above locked patches and seismic asperities. These areas are actually at extensional critical state and characterized by a very low effective friction. We thus suspect the extensional features to be related to earthquakes rather than basal erosion. We then look for similar relationships along the Sumatra subduction zone to see if basal erosion is a common process. The Tocopilla and Iquique earthquakes ruptured only part of the northern Chile seismic gap although the full segment was ready for a new large rupture. Areas of basal erosion might have impeded the propagation of these ruptures and could as well delineate the future mega-earthquake.

Improved high pressure turbine shroud

NASA Technical Reports Server (NTRS)

Bessen, I. I.; Rigney, D. V.; Schwab, R. C.

1977-01-01

A new high pressure turbine shroud material has been developed from the consolidation of prealloyed powders of Ni, Cr, Al and Y. The new material, a filler for cast turbine shroud body segments, is called Genaseal. The development followed the identification of oxidation resistance as the primary cause of prior shroud deterioration, since conversion to oxides reduces erosion resistance and increases spalling under thermal cycled engine conditions. The NICrAlY composition was selected in preference to NIAL and FeCRALY alloys, and was formulated to a prescribed density range that offers suitable erosion resistance, thermal conductivity and elastic modulus for improved behavior as a shroud.

Aircraft surface coatings

NASA Technical Reports Server (NTRS)

1982-01-01

Liquid, spray on elastomeric polyurethanes are selected and investigated as best candidates for aircraft external protective coatings. Flight tests are conducted to measure drag effects of these coatings compared to paints and a bare metal surface. The durability of two elastometric polyurethanes are assessed in airline flight service evaluations. Laboratory tests are performed to determine corrosion protection properties, compatibility with aircraft thermal anti-icing systems, the effect of coating thickness on erosion durability, and the erosion characteristics of composite leading edges-bare and coated. A cost and benefits assessment is made to determine the economic value of various coating configurations to the airlines.

Sediment Production and Storage Through a Glacial-Interglacial Cycle on a Cool-Temperate Glaciated Margin

NASA Astrophysics Data System (ADS)

Powell, R. D.

2001-12-01

The southern Alaska margin has high coastal mountains, which coupled with temperate glaciation, result in extremely high modern erosion rates (e.g. Jaeger et al., 2001), possibly exceeding rates of orogenic uplift (Meigs and Sauber, 2000). Where measured, modern sediment yields are among the highest of any basin worldwide (Hallet et al., 1996; Elverhoi et al., 1998; Jaeger et al., 1998). In Muir Inlet, Glacier Bay, sediment yields from slowly retreating glaciers decrease logarithmically with decreasing drainage basin area (Powell, 1991), a trend also reflected in regional data synthesized in Hallet et al. (1996). Alley (1997) then hypothesized that if erosion increases with basin area then where two tributaries join, deeper erosion would ensue, which is consistent with linear erosional troughs and hanging valleys. The idea is also consistent with the general downglacier increase in water flux at the glacier bed. However over longer periods, data from seismic profiles of the Gulf of Alaska shelf, show sediment yields are nearly the same through a glacial-interglacial cycle; regional data from other glaciated basins appear to confirm that trend (Elverhoi et al., 1998). If yields are continuously high from bedrock erosion, then why are mountains not eroded to base level because erosion rates are higher than isostatic uplift? Why are trends in yields apparently different during recent retreats with decreasing basin sizes than during longer term glacial cycles? Answers to these questions may be numerous and compound; however, one possibility will be evaluated. We know there is significant modern bedrock erosion occurring during glacial retreat and that also appears to have been the case during advance. Native stories describing the last (Little Ice Age) advance in Glacier Bay describe a large amount of sediment being produced (Powell et al., 1995) indicating that significant erosion was occurring. Fjord-wall stratigraphy shows that sediment had infilled much of the Bay up to ca. 200 m above modern sea level (Goldthwait,1986) prior to the LIA. During that advance, all sediments were then eroded down to bedrock, locally up to 400-500 m below sea level (Powell and Molnia, 1989), and then dumped at the Bay entrance, the site of maximum advance Powell et al., 1995). By inference, because most sediment packages on the shelf are deposited during glacially advanced phases, they probably mostly include sediment redistributed from fjords and inner shelf with a minor component from freshly eroded mountain bedrock. The ELA, under which most erosion may occur (Meigs and Sauber, 2000), lies over fjords during glacial maxima where the glacier is probably thickest with pressure melting and melting/freezing occurring at the bed. Erosion of sediment deposited there during a retreat phase may be enhanced, as may fjord over-deepening, whereas, thinner ice over mountains is likely to be cold at the bed, limiting erosion. As the glacier retreats the ELA moves toward the mountains as may the center of erosion, which then occurs mainly on bedrock. Mountain uplift may be enhanced during interglacials when glacio-isostatic rebound occurs and increased erosion adds to the isostatic effect. Therefore, during glacial-interglacial cycles average sediment yields from a glacier may not vary significantly, but the main centers of erosion change through time as does the eroding substrate and locations of depocenters.

Effects of Shoreline Dynamics on Saltmarsh Vegetation

PubMed Central

Sharma, Shailesh; Goff, Joshua; Moody, Ryan M.; McDonald, Ashley; Byron, Dorothy; Heck, Kenneth L.; Powers, Sean P.; Ferraro, Carl; Cebrian, Just

2016-01-01

We evaluated the impact of shoreline dynamics on fringing vegetation density at mid- and low-marsh elevations at a high-energy site in the northern Gulf of Mexico. Particularly, we selected eight unprotected shoreline stretches (75 m each) at a historically eroding site and measured their inter-annual lateral movement rate using the DSAS method for three consecutive years. We observed high inter-annual variability of shoreline movement within the selected stretches. Specifically, shorelines retrograded (eroded) in year 1 and year 3, whereas, in year 2, shorelines advanced seaward. Despite shoreline advancement in year 2, an overall net erosion was recorded during the survey period. Additionally, vegetation density generally declined at both elevations during the survey period; however, probably due to their immediate proximity with lateral erosion agents (e.g., waves, currents), marsh grasses at low-elevation exhibited abrupt reduction in density, more so than grasses at mid elevation. Finally, contrary to our hypothesis, despite shoreline advancement, vegetation density did not increase correspondingly in year 2 probably due to a lag in response from biota. More studies in other coastal systems may advance our knowledge of marsh edge systems; however, we consider our results could be beneficial to resource managers in preparing protection plans for coastal wetlands against chronic stressors such as lateral erosion. PMID:27442515

Effects of Shoreline Dynamics on Saltmarsh Vegetation.

PubMed

Sharma, Shailesh; Goff, Joshua; Moody, Ryan M; McDonald, Ashley; Byron, Dorothy; Heck, Kenneth L; Powers, Sean P; Ferraro, Carl; Cebrian, Just

2016-01-01

We evaluated the impact of shoreline dynamics on fringing vegetation density at mid- and low-marsh elevations at a high-energy site in the northern Gulf of Mexico. Particularly, we selected eight unprotected shoreline stretches (75 m each) at a historically eroding site and measured their inter-annual lateral movement rate using the DSAS method for three consecutive years. We observed high inter-annual variability of shoreline movement within the selected stretches. Specifically, shorelines retrograded (eroded) in year 1 and year 3, whereas, in year 2, shorelines advanced seaward. Despite shoreline advancement in year 2, an overall net erosion was recorded during the survey period. Additionally, vegetation density generally declined at both elevations during the survey period; however, probably due to their immediate proximity with lateral erosion agents (e.g., waves, currents), marsh grasses at low-elevation exhibited abrupt reduction in density, more so than grasses at mid elevation. Finally, contrary to our hypothesis, despite shoreline advancement, vegetation density did not increase correspondingly in year 2 probably due to a lag in response from biota. More studies in other coastal systems may advance our knowledge of marsh edge systems; however, we consider our results could be beneficial to resource managers in preparing protection plans for coastal wetlands against chronic stressors such as lateral erosion.

State of the art in protection of erosion-corrosion on vertical axis tidal current turbine

NASA Astrophysics Data System (ADS)

Musabikha, Siti; Utama, I. Ketut Aria Pria; Mukhtasor

2018-05-01

Vertical axis tidal current turbine is main part of ocean energy devices which converts the tidal current energy into electricity. Its development is arising too due to increased interest research topic concerning climate change mitigation. Due to its rotating movement, it will be induced mechanical forces, such as shear stress and/or particle impact. Because of its natural operations, vertical axis turbine is also being exposed to harsh and corroding marine environment itself. In order to secure the vertical tidal turbine devices from mechanical wear and corrosion effects which is lead to a material loss, an appropriate erosion-corrosion protection needs to be defined. Its protection actionscan be derived such as design factors, material selections, inhibitors usage, cathodic protections, and coatings. This paper aims to analyze protection method which is necessary to control erosion-corrosion phenomenon that appears to the vertical axis tidal current turbine.

Synthesising empirical results to improve predictions of post-wildfire runoff and erosion response

USGS Publications Warehouse

Shakesby, Richard A.; Moody, John A.; Martin, Deborah A.; Robichaud, Peter R.

2016-01-01

Advances in research into wildfire impacts on runoff and erosion have demonstrated increasing complexity of controlling factors and responses, which, combined with changing fire frequency, present challenges for modellers. We convened a conference attended by experts and practitioners in post-wildfire impacts, meteorology and related research, including modelling, to focus on priority research issues. The aim was to improve our understanding of controls and responses and the predictive capabilities of models. This conference led to the eight selected papers in this special issue. They address aspects of the distinctiveness in the controls and responses among wildfire regions, spatiotemporal rainfall variability, infiltration, runoff connectivity, debris flow formation and modelling applications. Here we summarise key findings from these papers and evaluate their contribution to improving understanding and prediction of post-wildfire runoff and erosion under changes in climate, human intervention and population pressure on wildfire-prone areas.

Ablative material testing for low-pressure, low-cost rocket engines

NASA Technical Reports Server (NTRS)

Richter, G. Paul; Smith, Timothy D.

1995-01-01

The results of an experimental evaluation of ablative materials suitable for the production of light weight, low cost rocket engine combustion chambers and nozzles are presented. Ten individual specimens of four different compositions of silica cloth-reinforced phenolic resin materials were evaluated for comparative erosion in a subscale rocket engine combustion chamber. Gaseous hydrogen and gaseous oxygen were used as propellants, operating at a nominal chamber pressure of 1138 kPa (165 psi) and a nominal mixture ratio (O/F) of 3.3. These conditions were used to thermally simulate operation with RP-1 and liquid oxygen, and achieved a specimen throat gas temperature of approximately 2456 K (4420 R). Two high-density composition materials exhibited high erosion resistance, while two low-density compositions exhibited approximately 6-75 times lower average erosion resistance. The results compare favorably with previous testing by NASA and provide adequate data for selection of ablatives for low pressure, low cost rocket engines.

Binational digital soils map of the Ambos Nogales watershed, southern Arizona and northern Sonora, Mexico

USGS Publications Warehouse

Norman, Laura

2004-01-01

We have prepared a digital map of soil parameters for the international Ambos Nogales watershed to use as input for selected soils-erosion models. The Ambos Nogales watershed in southern Arizona and northern Sonora, Mexico, contains the Nogales wash, a tributary of the Upper Santa Cruz River. The watershed covers an area of 235 km2, just under half of which is in Mexico. Preliminary investigations of potential erosion revealed a discrepancy in soils data and mapping across the United States-Mexican border due to issues including different mapping resolutions, incompatible formatting, and varying nomenclature and classification systems. To prepare a digital soils map appropriate for input to a soils-erosion model, the historical analog soils maps for Nogales, Ariz., were scanned and merged with the larger-scale digital soils data available for Nogales, Sonora, Mexico using a geographic information system.

Shoreline erosion at selected areas along Lake Sharpe on the Lower Brule Reservation in South Dakota, 1966–2015

USGS Publications Warehouse

Thompson, Ryan F.; Stamm, John F.

2018-06-21

The Lower Brule Reservation in central South Dakota is losing land because of shoreline erosion along Lake Sharpe, a reservoir on the Missouri River, which has caused detrimental effects for the Lower Brule Sioux Tribe including losses of cultural sites, recreation access points, wildlife habitat, irrigated cropland, and landmass. To better understand and quantify shoreline erosion, the Lower Brule Sioux Tribe and the U.S. Geological Survey cooperated on a series of data-collection efforts and study of shoreline erosion along Lake Sharpe. Data collected or compiled for 1966–2015 were used to describe and quantify shoreline erosion along Lake Sharpe. The progression of shoreline erosion near the community of Lower Brule, South Dakota, was tracked by comparing current or recent aerial imagery with existing historical maps. At 33 evaluation lines along a 7-mile reach of Lake Sharpe shoreline near Lower Brule, cumulative change of shoreline from 1966 to 2010 ranged from about −224 feet of deposition to 770 feet of erosion.Photographic and location data were collected for this study to understand the processes affecting erosion and estimate erosion rates. Photographs were collected only in the 7-mile reach near Lower Brule, but locations of the bank over time were collected at the 7-mile reach and two additional reaches within the Lower Brule Reservation. Global navigation satellite system equipment was used in real-time kinematic mode to collect bank locations along three reaches of interest. Reach-length data were collected four times between November 2011 and November 2012. A small, unmanned aerial system (drone) was used to capture digital video along the shoreline of the 7-mile reach.Water-level fluctuations contribute to the number of wet-dry cycles experienced by the soils at the shoreline or bank. The soils present under the current (2017) location of the reservoir are predominantly terrace alluvium, consisting of sand and silt. Detailed soils data for Lyman County indicate that the dominant soil type along the southern part of the shoreline in the 7-mile reach is Bullcreek clay. Weather within the study area can affect the erosion rate. Air temperature can potentially affect erosion rates by freezing and thawing water and soils. Mean hourly wind speeds vary somewhat throughout the year but averaged 13.3 miles per hour. The direction of prevailing winds near Lower Brule indicates that there are several miles of fetch to build large waves.Annual erosion rates calculated or measured throughout this study varied by location. Long-term annual average erosion rates of the 7-mile reach, as calculated by image analysis, ranged from −5.1 feet per year (deposition) to 17.5 feet per year (erosion). Short-term annual erosion rates measured using global navigation satellite system equipment during 2010–12 ranged from about 0 to 31.7 feet per year for the 7-mile reach. Existing scour countermeasures have been effective variably. Fieldstone rip-rap seems to have stabilized the shoreline, whereas tree strips paralleling the shoreline seem to have slowed erosion.

Humid site stabilization and closure

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cutshall, N.H.

1981-01-01

The purpose of the work described here is to identify and evaluate the importance of factors that are expected to dictate the nature of site stabilization and closure requirements. Subsequent efforts will plan for implementation of such requirements. Two principal areas of site stabilization and closure effort will be pursued initially - geological management and vegetation management. The geological effort will focus on chemical weathering and surficial erosion. Such catastrophic geologic events as landslides, flooding, earthquakes, volcanos, etc. are already considered in site selection and operation and these factors will not be emphasized initially. Vegetation management will be designed tomore » control erosion, to minimize nuclide mobilization by roots and to be compatible with natural successional pressures. It is anticipated that the results of this work will be important both to site selection and operation as well as the actual stabilization and closure procedure.« less

Health Sensing Functions in Thermal Barrier Coatings Incorporating Rare-Earth-Doped Luminescent Sublayers

NASA Technical Reports Server (NTRS)

Eldridge, J. I.; Singh, J.; Wolfe, D. E.

2004-01-01

Great effort has been directed towards developing techniques to monitor the health of thermal barrier coatings (TBCs) that would detect the approach of safety-threatening conditions. An unconventional approach is presented here where health sensing functionality is integrated into the TBC itself by the incorporation of rare-earth-doped luminescent sublayers to monitor erosion as well as whether the TBC is maintaining the underlying substrate at a sufficiently low temperature. Erosion indication is demonstrated in electron-beam physical vapor deposited (EB-PVD) TBCs consisting of 7wt% yttria-stabilized zirconia (7YSZ) with europium-doped and terbium-doped sublayers. Multiple ingot deposition produced sharp boundaries between the doped sublayers without interrupting the columnar growth of the TBC. The TBC-coated specimens were subjected to alumina particle jet erosion, and the erosion depth was then indicated under ultraviolet illumination that excited easily visible luminescence characteristic of sublayer that was exposed by erosion. In addition, temperature measurements from a bottom-lying europium-doped sublayer in a TBC produced by multiple ingot EB-PVD were accomplished by measuring the temperature-dependent decay time from the 606 nm wavelength emission excited in that sublayer with a 532 nm wavelength laser that was selected for its close match to one of the europium excitation wavelengths as well as being at a wavelength where the TBC is relatively transparent. It is proposed the low dopant levels and absence of interruption of the TBC columnar growth allow the addition of the erosion and temperature sensing functions with minimal effects on TBC performance.

Cosmogenic 10Be and 26Al exposure ages of tors and erratics, Cairngorm Mountains, Scotland: Timescales for the development of a classic landscape of selective linear glacial erosion

USGS Publications Warehouse

Phillips, W.M.; Hall, A.M.; Mottram, R.; Fifield, L.K.; Sugden, D.E.

2006-01-01

The occurrence of tors within glaciated regions has been widely cited as evidence for the preservation of relic pre-Quaternary landscapes beneath protective covers of non-erosive dry-based ice. Here, we test for the preservation of pre-Quaternary landscapes with cosmogenic surface exposure dating of tors. Numerous granite tors are present on summit plateaus in the Cairngorm Mountains of Scotland where they were covered by local ice caps many times during the Pleistocene. Cosmogenic 10Be and 26Al data together with geomorphic relationships reveal that these landforms are more dynamic and younger than previously suspected. Many Cairngorm tors have been bulldozed and toppled along horizontal joints by ice motion, leaving event surfaces on tor remnants and erratics that can be dated with cosmogenic nuclides. As the surfaces have been subject to episodic burial by ice, an exposure model based upon ice and marine sediment core proxies for local glacial cover is necessary to interpret the cosmogenic nuclide data. Exposure ages and weathering characteristics of tors are closely correlated. Glacially modified tors and boulder erratics with slightly weathered surfaces have 10Be exposure ages of about 15 to 43 ka. Nuclide inheritance is present in many of these surfaces. Correction for inheritance indicates that the eastern Cairngorms were deglaciated at 15.6 ?? 0.9 ka. Glacially modified tors with moderate to advanced weathering features have 10Be exposure ages of 19 to 92 ka. These surfaces were only slightly modified during the last glacial cycle and gained much of their exposure during the interstadial of marine Oxygen Isotope Stage 5 or earlier. Tors lacking evidence of glacial modification and exhibiting advanced weathering have 10Be exposure ages between 52 and 297 ka. Nuclide concentrations in these surfaces are probably controlled by bedrock erosion rates instead of discrete glacial events. Maximum erosion rates estimated from 10Be range from 2.8 to 12.0 mm/ka, with an error weighted mean of 4.1 ?? 0.2 mm/ka. Three of these surfaces yield model exposure-plus-burial ages of 295-71+84, 520-141+178, and 626-85+102 ka. A vertical cosmogenic nuclide profile across the oldest sampled tor indicates a long-term emergence rate of 31 ?? 2 mm/ka. These findings show that dry-based ice caps are capable of substantially eroding tors by entraining blocks previously detached by weathering processes. Bedrock surfaces and erratic boulders in such settings are likely to have nuclide inheritance and may yield erroneous (too old) exposure ages. While many Cairngorm tors have survived multiple glacial cycles, rates of regolith stripping and bedrock erosion are too high to permit the widespread preservation of pre-Quaternary rock surfaces. ?? 2005 Elsevier B.V. All rights reserved.

A Sensitive Technique Using Atomic Force Microscopy to Measure the Low Earth Orbit Atomic Oxygen Erosion of Polymers

NASA Technical Reports Server (NTRS)

deGroh, Kim K.; Banks, Bruce A.; Clark, Gregory W.; Hammerstrom, Anne M.; Youngstrom, Erica E.; Kaminski, Carolyn; Fine, Elizabeth S.; Marx, Laura M.

2001-01-01

Polymers such as polyimide Kapton and Teflon FEP (fluorinated ethylene propylene) are commonly used spacecraft materials due to their desirable properties such as flexibility, low density, and in the case of FEP low solar absorptance and high thermal emittance. Polymers on the exterior of spacecraft in the low Earth orbit (LEO) environment are exposed to energetic atomic oxygen. Atomic oxygen erosion of polymers occurs in LEO and is a threat to spacecraft durability. It is therefore important to understand the atomic oxygen erosion yield (E, the volume loss per incident oxygen atom) of polymers being considered in spacecraft design. Because long-term space exposure data is rare and very costly, short-term exposures such as on the shuttle are often relied upon for atomic oxygen erosion determination. The most common technique for determining E is through mass loss measurements. For limited duration exposure experiments, such as shuttle experiments, the atomic oxygen fluence is often so small that mass loss measurements can not produce acceptable uncertainties. Therefore, a recession measurement technique has been developed using selective protection of polymer samples, combined with postflight atomic force microscopy (AFM) analysis, to obtain accurate erosion yields of polymers exposed to low atomic oxygen fluences. This paper discusses the procedures used for this recession depth technique along with relevant characterization issues. In particular, a polymer is salt-sprayed prior to flight, then the salt is washed off postflight and AFM is used to determine the erosion depth from the protected plateau. A small sample was salt-sprayed for AFM erosion depth analysis and flown as part of the Limited Duration Candidate Exposure (LDCE-4,-5) shuttle flight experiment on STS-51. This sample was used to study issues such as use of contact versus non-contact mode imaging for determining recession depth measurements. Error analyses were conducted and the percent probable error in the erosion yield when obtained by the mass loss and recession depth techniques has been compared. The recession depth technique is planned to be used to determine the erosion yield of 42 different polymers in the shuttle flight experiment PEACE (Polymer Erosion And Contamination Experiment) planned to fly in 2002 or 2003.

In vitro assessment of artificial saliva formulations on initial enamel erosion remineralization.

PubMed

Ionta, Franciny Querobim; Mendonça, Fernanda Lyrio; de Oliveira, Gabriela Cristina; de Alencar, Catarina Ribeiro Barros; Honório, Heitor Marques; Magalhães, Ana Carolina; Rios, Daniela

2014-02-01

Various formulations of artificial saliva are present in the literature and little guidance is available on the standardization of type of saliva for use in in vitro protocols for erosive studies. The aim of this study was to evaluate the remineralizing capacity of different formulations of artificial saliva on initial enamel erosive lesion. Bovine enamel blocks were subjected to short-term acidic exposure by immersion in citric acid 0.05 M (pH 2.5) for 15s, resulting in surface softening without tissue loss. Then 90 selected eroded enamel blocks were randomly and equally divided into 6 groups according to saliva formulation (n=15): Saliva 1 (contain mucin); Saliva 2 (Saliva 1 without mucin); Saliva 3; Saliva 4; Saliva 5 (contain sodium carboxymethyl cellulose) and control (C) (deionized water). After demineralization enamel blocks were subjected to remineralization by immersion in the saliva's formulations for 2h. Enamel remineralization was measured by superficial hardness test (% superficial hardness change). The data were tested using ANOVA and Tukey's test (p<0.05). All the tested formulations of artificial saliva resulted in significantly higher enamel remineralization compared to control (p<0.001). Saliva 3 showed higher percentage of enamel remineralization than Saliva 5 (p<0.05). Besides the variety of artificial saliva for erosion in vitro protocols, all the formulations tested were able to partially remineralize initial erosive lesions. Copyright © 2013. Published by Elsevier Ltd.

Coupled analysis on landscape pattern and hydrological processes in Yanhe watershed of China.

PubMed

Li, J; Zhou, Z X

2015-02-01

As a typical experimental Soil and Water Conservation District, Yanhe watershed has long been plagued by soil erosion due to severe human disturbances. Exerting remote sensing (RS) and geographic information system (GIS) technology, this paper firstly analyzed and simulated ecological hydrological process in Yanhe watershed based on SWAT model, constructed a comprehensive landscape indices which was closely related to soil erosion, and reflected the coupling relationship between regional landscape pattern change and soil erosion. The results are as follows: (1) Areas of different land use types remained relatively stable from 1990 to 2000 and then changed drastically from 2000 to 2010, which was characterized by lawn expansion and cultivated land shrinkage. (2) In terms of the spatial heterogeneity of hydrological response unit (HRUs), the correlation coefficient of seven selected landscape indices and runoff was very small, and cannot pass all significant testing. But correlation between the indices and sediment yield except for Total Core Area (TCA) and Interspersion and Juxtaposition Index (IJI) was remarkable. (3) According to 'the source-sink' theory of soil erosion, new landscape index-slope-HRU landscape index (SHLI) was built, and reflected the relationship between landscape pattern and soil erosion processes to a certain extent. (4) Coupling relationship between SHLI in 2010 and annual sediment was very prominent. In the sub-basin scale, SHLI has obvious regional differentiation from annual sediment. Copyright © 2014 Elsevier B.V. All rights reserved.

Development of a statistical model for the determination of the probability of riverbank erosion in a Meditteranean river basin

NASA Astrophysics Data System (ADS)

Varouchakis, Emmanouil; Kourgialas, Nektarios; Karatzas, George; Giannakis, Georgios; Lilli, Maria; Nikolaidis, Nikolaos

2014-05-01

Riverbank erosion affects the river morphology and the local habitat and results in riparian land loss, damage to property and infrastructures, ultimately weakening flood defences. An important issue concerning riverbank erosion is the identification of the areas vulnerable to erosion, as it allows for predicting changes and assists with stream management and restoration. One way to predict the vulnerable to erosion areas is to determine the erosion probability by identifying the underlying relations between riverbank erosion and the geomorphological and/or hydrological variables that prevent or stimulate erosion. A statistical model for evaluating the probability of erosion based on a series of independent local variables and by using logistic regression is developed in this work. The main variables affecting erosion are vegetation index (stability), the presence or absence of meanders, bank material (classification), stream power, bank height, river bank slope, riverbed slope, cross section width and water velocities (Luppi et al. 2009). In statistics, logistic regression is a type of regression analysis used for predicting the outcome of a categorical dependent variable, e.g. binary response, based on one or more predictor variables (continuous or categorical). The probabilities of the possible outcomes are modelled as a function of independent variables using a logistic function. Logistic regression measures the relationship between a categorical dependent variable and, usually, one or several continuous independent variables by converting the dependent variable to probability scores. Then, a logistic regression is formed, which predicts success or failure of a given binary variable (e.g. 1 = "presence of erosion" and 0 = "no erosion") for any value of the independent variables. The regression coefficients are estimated by using maximum likelihood estimation. The erosion occurrence probability can be calculated in conjunction with the model deviance regarding the independent variables tested (Atkinson et al. 2003). The developed statistical model is applied to the Koiliaris River Basin in the island of Crete, Greece. The aim is to determine the probability of erosion along the Koiliaris' riverbanks considering a series of independent geomorphological and/or hydrological variables. Data for the river bank slope and for the river cross section width are available at ten locations along the river. The riverbank has indications of erosion at six of the ten locations while four has remained stable. Based on a recent work, measurements for the two independent variables and data regarding bank stability are available at eight different locations along the river. These locations were used as validation points for the proposed statistical model. The results show a very close agreement between the observed erosion indications and the statistical model as the probability of erosion was accurately predicted at seven out of the eight locations. The next step is to apply the model at more locations along the riverbanks. In November 2013, stakes were inserted at selected locations in order to be able to identify the presence or absence of erosion after the winter period. In April 2014 the presence or absence of erosion will be identified and the model results will be compared to the field data. Our intent is to extend the model by increasing the number of independent variables in order to indentify the key factors favouring erosion along the Koiliaris River. We aim at developing an easy to use statistical tool that will provide a quantified measure of the erosion probability along the riverbanks, which could consequently be used to prevent erosion and flooding events. Atkinson, P. M., German, S. E., Sear, D. A. and Clark, M. J. 2003. Exploring the relations between riverbank erosion and geomorphological controls using geographically weighted logistic regression. Geographical Analysis, 35 (1), 58-82. Luppi, L., Rinaldi, M., Teruggi, L. B., Darby, S. E. and Nardi, L. 2009. Monitoring and numerical modelling of riverbank erosion processes: A case study along the Cecina River (central Italy). Earth Surface Processes and Landforms, 34 (4), 530-546. Acknowledgements This work is part of an on-going THALES project (CYBERSENSORS - High Frequency Monitoring System for Integrated Water Resources Management of Rivers). The project has been co-financed by the European Union (European Social Fund - ESF) and Greek national funds through the Operational Program "Education and Lifelong Learning" of the National Strategic Reference Framework (NSRF) - Research Funding Program: THALES. Investing in knowledge society through the European Social Fund.

Estimation of contraction scour in riverbed using SERF

USGS Publications Warehouse

Jiang, J.; Ganju, N.K.; Mehta, A.J.

2004-01-01

Contraction scour in a firm-clay estuarine riverbed is estimated at an oil-unloading terminal at the Port of Haldia in India, where a scour hole attained a maximum depth greater than 5 m relative to the original bottom. A linear equation for the erosion flux as a function of the excess bed shear stress was semicalibrated in a rotating-cylinder device called SERF (Simulator of Erosion Rate Function) and coupled to a hydrodynamic code to simulate the hole as a clear-water scour process. SERF, whose essential design is based on previous such devices, additionally included a load cell for in situ and rapid measurement of the eroded sediment mass. Based on SERF's performance and the degree of comparison between measured and simulated hole geometry, it appears that this device holds promise as a simple tool for prediction of scour in firm-clay beds. ?? ASCE.

Quantifying the Spatial Distribution of Hill Slope Erosion Using a 3-D Laser Scanner

NASA Astrophysics Data System (ADS)

Scholl, B. N.; Bogonko, M.; He, Y.; Beighley, R. E.; Milberg, C. T.

2007-12-01

Soil erosion is a complicated process involving many interdependent variables including rainfall intensity and duration, drop size, soil characteristics, ground cover, and surface slope. The interplay of these variables produces differing spatial patterns of rill versus inter-rill erosion by changing the effective energy from rain drop impacts and the quantities and timing of sheet and shallow, concentrated flow. The objective of this research is to characterize the spatial patterns of rill and inter-rill erosion produced from simulated rainfall on different soil densities and surface slopes using a 3-D laser scanner. The soil used in this study is a sandy loam with bulk density due to compaction ranging from 1.25-1.65 g/cm3. The surface slopes selected for this study are 25, 33, and 50 percent and represent common slopes used for grading on construction sites. The spatial patterns of soil erosion are measured using a Trimble GX DR 200+ 3D Laser Scanner which employs a time of flight calculation averaged over 4 points using a class 2, pulsed, 532 nm, green laser at a distance of 2 to 11 m from the surface. The scanner measures point locations on an approximately 5 mm grid. The pre- and post-erosion scan surfaces are compared to calculate the change in volume and the dimensions of rills and inter-rill areas. The erosion experiments were performed in the Soil Erosion Research Laboratory (SERL), part of the Civil and Environmental Engineering department at San Diego State University. SERL experiments utilize a 3-m by 10-m tilting soil bed with a soil depth of 0.5 meters. Rainfall is applied to the soil surface using two overhead Norton ladder rainfall simulators, which produce realistic rain drop diameters (median = 2.25 mm) and impact velocities. Simulated storm events used in this study consist of rainfall intensities ranging from 5, 10 to 15 cm/hr for durations of 20 to 30 minutes. Preliminary results are presented that illustrate a change in runoff processes and erosion patterns as soil density increases and reduces infiltration characteristics. Total soil loss measured from the bottom of the erosion bed is compared to the volume of soil loss determined using the laser scanner. Due to soil consolidation during the experiment, the accuracy of measured soil loss from the laser scanner increases with increasing soil density. Ratios of rill and inter-rill erosions for each experiment are also presented. URL: http://spatialhydro.sdsu.edu

Standardization of splash device

NASA Astrophysics Data System (ADS)

Fernández Raga, María; Peters, Piet

2017-04-01

The erosion is a complex process that has been studied extensively by numerous researchers, requiring a prolongued time effort and a large economic investment. To be effective, the measurements of erosion should be precise, controlled and replicable, and to assure efectiveness, measurement devices of erosion should be properly designed, constructed, well calibrated and also they should be operated by a trained person (Stroosnijder, 2005). Because researchers try to improve old devices, the equipment is constantly being redesigned, making the measurements not comparable and furthermore, producing a lack of available standarized device. The lack of standardization of erosion equipment is more obvious in the case of the local splash erosion, where the nature of the process makes very difficult to isolate its effects. In this article we compare the results obtained from five of the most common splash erosion devices (selected from more than 16 different currently types), under the same rain conditions, with the objective of facilitate the standardization of the method that will be more easy to build, minimizing the error. A set of six splash devices were setted in well known positions under simulated rain, to measured the differences, among devices and the accuracy of the data recovered after 10 minutes of rainfall simulation under different intensities (from 60 to 130 mm/h). The rainfall simulator of Wageningen was used, using sand as splash erosion source. Differences in the infiltration were also measured, and a calibration of sizes and speeds of the raindrops was done using the photography method (Hamidreza-Sadeghi et al., 2013). The splash devices selected for this study were unbounded splash devices (like the funnel, the cup (Fernandez-Raga et al., 2010) and the splash flume (Jomaa et al., 2010)), and bounded devices that allow the calculation of splash rate, (like the new cup (Scholten et al., 2011) and the Morgan tray). The behaviour of different splash devices with the changes of intensity will be explained and discussed, with a recommendation of use. References Fernandez-Raga, M, Fraile, R, Keizer, J, Teijeiro, MEV, Castro, A, Palencia, C, Koenders, J and Marques, RLD. 2010. The kinetic energy of rain measured with an optical disdrometer: An application to splash erosion. Atmospheric Research 96, 225-240. doi: 10.1016/j.atmosres.2009.07.013 Hamidreza-Sadeghi, S, Abdollahi, Z and Khaledi-Darvishan, A. 2013. Experimental comparison of some techniques for estimating natural raindrop size distribution on the south coast of the Caspian Sea, Iran. Hydrological sciences Journal 58, 1374-1382. doi: 10.1080/02626667.2013.814917 Jomaa, S, Barry, D, Brovelli, A, Sander, G, Parlange, J, Heng, B and Tromp-van Meerveld, H. 2010. Effect of raindrop splash and transversal width on soil erosion: Laboratory flume experiments and analysis with the Hairsine-Rose model. Journal of Hydrology 395, 117-132. doi: 10.1016/j.jhydrol.2010.10.021 Scholten, T, Geißler, C, Goc, J, Kühn, P and Wiegand, C. 2011. A new splash cup to measure the kinetic energy of rainfall. Journal of Plant Nutrition and Soil Science 174, 596-601. doi: 10.1002/jpln.201000349 Stroosnijder, L. 2005. Measurement of erosion: is it possible? Catena 64, 162-173. doi: 10.1016/j.catena.2005.08.004

Effect of Contact Damage on the Strength of Ceramic Materials.

DTIC Science & Technology

1982-10-01

variables that are important to erosion, and a multivariate , linear regression analysis is used to fit the data to the dimensional analysis. The...of Equations 7 and 8 by a multivariable regression analysis (room tem- perature data) Exponent Regression Standard error Computed coefficient of...1980) 593. WEAVER, Proc. Brit. Ceram. Soc. 22 (1973) 125. 39. P. W. BRIDGMAN, "Dimensional Analaysis ", (Yale 18. R. W. RICE, S. W. FREIMAN and P. F

Erosion measurements at various scales in a semi arid mountainous catchment - case of the Rheraya watershed, High Atlas, Morocco

NASA Astrophysics Data System (ADS)

Cheggour, A.; Simonneaux, V.; Roose, E.

2009-04-01

Erosion is a critical phenomenon in North Africa, under the combined effects of aggressive rainfall and soil fragility, increased by the grazing pressure on rangelands. However measurements of actual erosion rates are rare, especially in mountainous areas. Siltation of dams is estimated at more than 60 million m3 annually in Morocco, which corresponds to a decrease of 0.5% of the storage capacity. The Rheraya watershed (225 km2) is located in a semi-arid climat, in the High Atlas of Morocco. In order to assess erosion processes at various scales, three types of measurements were achieved on this area, namely rainfall simulation tests one square meter, erosion plots on 150 m2, and catchment's discharge and associated sediments measurements. Rainfall simulation experiments were achieved on 27 sites, measuring runoff and sediment charge. The turbidity was correctly measured thanks to the development of a new runoff collector which doesn't disturb the soil. In the scope of spatial extrapolation, we searched for indicators obtained from ground description variables and/or by laboratory tests on soil samples, which were well correlated with infiltration and turbidity of the simulations. For the various soils present in the study area, the results show a large variability of infiltration (from 1 to 70 mm h-1) and turbidity (from 3 to 325 g.l-1). Analysis showed that infiltration is correlated mainly with texture and soil surface opening, and that turbidity is related to the surface of bare soil exposed to runoff. Six erosion plots of about 150 m2, located on various soil and land cover conditions, were measured during four years. The observations showed very rare runoff events in the main part of the watershed, producing a low sediment load (between 0.015 and 2.5 t.ha1.year1). Conversely, runoff was much more frequent on silty badlands, producing about 95% of the watershed sediment (350 t.ha-1.year-1) despite their area was only 1% of the watershed. There was a significant linear relation between simulation turbidity and erosion plot turbidity. However, there was a great difference between infiltration estimates from the two types of measurements. Plot infiltrations estimates were only between 3 and 5 mm/h, but they were significantly correlated to the one from test, through an exponential relation. Finally, an estimate of the overall erosion at catchment's scale was achieved from plots values extrapolated using a soil map, and gave about 3 to 4 t.ha-1.year-1. A good correlation was found between this watershed scale estimate and the catchment's exportation, indirectly validating the significance of both measurements. Moreover, both estimates were about the same, showing a sediment delivery ratio around one. Keywords: erosion, rainfall simulation, erosion plot, sediment exportation

Relationship between Risk Behavior for Eating Disorders and Dental Caries and Dental Erosion.

PubMed

Brandt, Lorenna Mendes Temóteo; Fernandes, Liege Helena Freitas; Aragão, Amanda Silva; Aguiar, Yêska Paola Costa; Auad, Sheyla Márcia; de Castro, Ricardo Dias; Cavalcanti, Sérgio D'Ávila Lins Bezerra; Cavalcanti, Alessandro Leite

2017-01-01

The aim of this study was to evaluate whether there is an association between risk behavior for eating disorders (EDs) and dental erosion and caries. A controlled cross-sectional study was conducted in Brazil, involving 850 randomly selected female adolescents. After evaluating risk behavior for eating disorders through the Bulimic Investigatory Test of Edinburgh, 12 adolescents were identified with severe risk behavior for EDs and matched to 48 adolescents without such risk. Dental examinations, anthropometric measurements, and eating habits and oral hygiene were performed. Adolescents with high severity eating disorder condition were not more likely to show dental caries ( p = 0.329; OR = 2.2, 95% CI: 0.35-13.72) or dental erosion ( p = 0.590; OR = 2.33; 95% CI: 0.56-9.70). Adolescents with high body mass index (BMI) were five times more likely to have high severity eating disorder condition ( p = 0.031; OR = 5.1; 95% CI: 1.61-23.07). Therefore, high severity risk behavior for EDs was not significantly associated with dental caries and dental erosion. However, high BMI was a risk factor for developing eating disorders and should be an alert for individuals with this condition.

Relationship between Risk Behavior for Eating Disorders and Dental Caries and Dental Erosion

PubMed Central

Brandt, Lorenna Mendes Temóteo; Fernandes, Liege Helena Freitas; Aragão, Amanda Silva; Cavalcanti, Sérgio D'Ávila Lins Bezerra

2017-01-01

The aim of this study was to evaluate whether there is an association between risk behavior for eating disorders (EDs) and dental erosion and caries. A controlled cross-sectional study was conducted in Brazil, involving 850 randomly selected female adolescents. After evaluating risk behavior for eating disorders through the Bulimic Investigatory Test of Edinburgh, 12 adolescents were identified with severe risk behavior for EDs and matched to 48 adolescents without such risk. Dental examinations, anthropometric measurements, and eating habits and oral hygiene were performed. Adolescents with high severity eating disorder condition were not more likely to show dental caries (p = 0.329; OR = 2.2, 95% CI: 0.35–13.72) or dental erosion (p = 0.590; OR = 2.33; 95% CI: 0.56–9.70). Adolescents with high body mass index (BMI) were five times more likely to have high severity eating disorder condition (p = 0.031; OR = 5.1; 95% CI: 1.61–23.07). Therefore, high severity risk behavior for EDs was not significantly associated with dental caries and dental erosion. However, high BMI was a risk factor for developing eating disorders and should be an alert for individuals with this condition. PMID:29423431

A Million-Year Record of Glaciation in the Tropical Andes

NASA Astrophysics Data System (ADS)

Smith, J. A.; Seltzer, G. O.; Rodbell, D. T.; Farber, D. L.; Finkel, R. C.

2004-12-01

We present a longterm record of glaciation in the tropical Andes based on cosmogenic dating (10Be) of boulders on moraines. Well-preserved moraines in deglaciated valleys bordering the Junin Plain in central Peru ( ˜11° S, 76° W, 4000 m) were deposited during several glacial cycles extending back more than one million years before present (1 Myr BP). The presence of boulders with zero-erosion 10Be exposure ages >1 Myr constrains boulder erosion rates to relatively low values. For boulders at high altitudes, however, even low boulder erosion rates (0.3 to 0.5 m/Myr) make calculated old exposure ages markedly older [e.g., ˜20% older for a zero-erosion age of 400,000 10Be years (400 10Be kyr)]. Exposure ages recalculated with boulder erosion rates of 0.3 m/Myr straddle interglacial marine isotope stage (MIS) 11 ( ˜430-390 kyr BP), fall within glacial MIS 12 ( ˜480-430 kyr BP), but skip over glacial MIS 16 ( ˜670-630 kyr BP), perhaps the largest ice volume of the past 2 Myr. Increasing the erosion rate used in the calculations to 0.5 m/Myr moves ages into both MIS 11 and MIS 16. If we assume that the older Andean glaciations were indeed synchronous with global ice volume, our data suggest that boulder preservation cannot be treated as a simple linear process. Conversely, the data may be suggesting correctly that glaciation of the tropical Andes was not synchronous with the global glaciations as inferred from the marine isotope record. Our chronology for the last glacial maximum (LGM) in the region supports the idea of asynchrony between the global ice volume record and the terrestrial record of glaciation in the tropical Andes. The LGM in the Junin region of Peru and in the Cordillera Real of Bolivia (16° S 68° W) occurred ˜34 to 22 10Be kyr BP and was less extensive than older glaciations. Asynchrony between the LGM in the Northern Hemisphere ( ˜21 kyr BP) and the tropical Andes suggests that previous glaciations in the tropical Andes may have been similarly out of step.

Regional soil erosion assessment based on a sample survey and geostatistics

NASA Astrophysics Data System (ADS)

Yin, Shuiqing; Zhu, Zhengyuan; Wang, Li; Liu, Baoyuan; Xie, Yun; Wang, Guannan; Li, Yishan

2018-03-01

Soil erosion is one of the most significant environmental problems in China. From 2010 to 2012, the fourth national census for soil erosion sampled 32 364 PSUs (Primary Sampling Units, small watersheds) with the areas of 0.2-3 km2. Land use and soil erosion controlling factors including rainfall erosivity, soil erodibility, slope length, slope steepness, biological practice, engineering practice, and tillage practice for the PSUs were surveyed, and the soil loss rate for each land use in the PSUs was estimated using an empirical model, the Chinese Soil Loss Equation (CSLE). Though the information collected from the sample units can be aggregated to estimate soil erosion conditions on a large scale; the problem of estimating soil erosion condition on a regional scale has not been addressed well. The aim of this study is to introduce a new model-based regional soil erosion assessment method combining a sample survey and geostatistics. We compared seven spatial interpolation models based on the bivariate penalized spline over triangulation (BPST) method to generate a regional soil erosion assessment from the PSUs. Shaanxi Province (3116 PSUs) in China was selected for the comparison and assessment as it is one of the areas with the most serious erosion problem. Ten-fold cross-validation based on the PSU data showed the model assisted by the land use, rainfall erosivity factor (R), soil erodibility factor (K), slope steepness factor (S), and slope length factor (L) derived from a 1 : 10 000 topography map is the best one, with the model efficiency coefficient (ME) being 0.75 and the MSE being 55.8 % of that for the model assisted by the land use alone. Among four erosion factors as the covariates, the S factor contributed the most information, followed by K and L factors, and R factor made almost no contribution to the spatial estimation of soil loss. The LS factor derived from 30 or 90 m Shuttle Radar Topography Mission (SRTM) digital elevation model (DEM) data worsened the estimation when used as the covariates for the interpolation of soil loss. Due to the unavailability of a 1 : 10 000 topography map for the entire area in this study, the model assisted by the land use, R, and K factors, with a resolution of 250 m, was used to generate the regional assessment of the soil erosion for Shaanxi Province. It demonstrated that 54.3 % of total land in Shaanxi Province had annual soil loss equal to or greater than 5 t ha-1 yr-1. High (20-40 t ha-1 yr-1), severe (40-80 t ha-1 yr-1), and extreme ( > 80 t ha-1 yr-1) erosion occupied 14.0 % of the total land. The dry land and irrigated land, forest, shrubland, and grassland in Shaanxi Province had mean soil loss rates of 21.77, 3.51, 10.00, and 7.27 t ha-1 yr-1, respectively. Annual soil loss was about 207.3 Mt in Shaanxi Province, with 68.9 % of soil loss originating from the farmlands and grasslands in Yan'an and Yulin districts in the northern Loess Plateau region and Ankang and Hanzhong districts in the southern Qingba mountainous region. This methodology provides a more accurate regional soil erosion assessment and can help policymakers to take effective measures to mediate soil erosion risks.

Atomic Oxygen Fluence Monitor

NASA Technical Reports Server (NTRS)

Banks, Bruce A.

2011-01-01

This innovation enables a means for actively measuring atomic oxygen fluence (accumulated atoms of atomic oxygen per area) that has impinged upon spacecraft surfaces. Telemetered data from the device provides spacecraft designers, researchers, and mission managers with real-time measurement of atomic oxygen fluence, which is useful for prediction of the durability of spacecraft materials and components. The innovation is a compact fluence measuring device that allows in-space measurement and transmittance of measured atomic oxygen fluence as a function of time based on atomic oxygen erosion yields (the erosion yield of a material is the volume of material that is oxidized per incident oxygen atom) of materials that have been measured in low Earth orbit. It has a linear electrical response to atomic oxygen fluence, and is capable of measuring high atomic oxygen fluences (up to >10(exp 22) atoms/sq cm), which are representative of multi-year low-Earth orbital missions (such as the International Space Station). The durability or remaining structural lifetime of solar arrays that consist of polymer blankets on which the solar cells are attached can be predicted if one knows the atomic oxygen fluence that the solar array blanket has been exposed to. In addition, numerous organizations that launch space experiments into low-Earth orbit want to know the accumulated atomic oxygen fluence that their materials or components have been exposed to. The device is based on the erosion yield of pyrolytic graphite. It uses two 12deg inclined wedges of graphite that are over a grit-blasted fused silica window covering a photodiode. As the wedges erode, a greater area of solar illumination reaches the photodiode. A reference photodiode is also used that receives unobstructed solar illumination and is oriented in the same direction as the pyrolytic graphite covered photodiode. The short-circuit current from the photodiodes is measured and either sent to an onboard data logger, or transmitted to a receiving station on Earth. By comparison of the short-circuit currents from the fluence-measuring photodiode and the reference photodiode, one can compute the accumulated atomic oxygen fluence arriving in the direction that the fluence monitor is pointing. The device produces a signal that is linear with atomic oxygen fluence using a material whose atomic oxygen erosion yield has been measured over a period of several years in low-Earth orbit.

Groundwater-Surface Water Interaction: A Case Study of Embankment Dam Safety Assessment in Sweden.

NASA Astrophysics Data System (ADS)

Ferdos, F.; Dargahi, B.

2015-12-01

Seepage, when excessive and unimpeded, can cause embankment dam failure. Such failures are often initiated by internal erosion and piping. Modelling these phenomena in embankment dams, accounting for the groundwater-surface water interactions, is crucial when performing dam safety assessments. The aim of this study was to evaluate the applicability of modelling seepage flows in multi-region dams using a finite element based multi-physics model. The model was applied to the Trängslet dam, the largest dam in Sweden. The objectives were to analyze the characteristics of both the flow and the surface-ground water interactions occurring in the dam, including: i) the saturated and unsaturated laminar flow regimes within the dam body, ii) the non-linear through-flow in the dam shoulders' coarse material, iii) the influence of the surface waves in the reservoir on the seepage flow by coupling the physics to a hydrodynamic interface, and iv) the influence of a conceptual "erosion tunnel" on the seepage flow and its interaction with the surface water flow by coupling the physics to a CFD interface. The focus of the study was on the influence of the transient water head boundary condition, surface waves and the internal erosion tunnel on the location of the phreatic line and the seepage flow rate. The simulated seepage flow of the dam in its original condition tallied with the monitoring measurements (40-70 l/s). The main feature found was the relatively high position of the phreatic line, which could compromise the stability of the dam. The combination of the seepage model with the reservoir hydrodynamics indicated a negligible influence of the surface waves on seepage flow. Results from the combination of the seepage model with fluid dynamics indicated that a conceptual "erosion tunnel" placed within the dam, even as high as in the unsaturated zone, significantly affects the phreatic line's position. This also causes the seepage flow to increase by several orders of magnitude, resulting in non-linear turbulent flow regimes in the downstream shoulder of the dam and, ultimately, dam failure. While the modelling was limited by a lack of reliable geometrical and geotechnical data, the results of the study do highlight the importance of including groundwater-surface water interactions in dam safety assessments.

Feedbacks between subglacial dynamics and long-term glacial landscape evolution (Invited)

NASA Astrophysics Data System (ADS)

Brædstrup, C. F.; Egholm, D. L.; Ugelvig, S. V.; Christensen, A. D.; Andersen, J. L.

2011-12-01

Several well-known glacial landforms (such as U-shaped troughs and cirques) are associated with characteristic length scales, indicating that the viscosity of the ice and the stress gradients associated with ice flow exert first-order controls on their formation. The evolution of these glacial landforms has so far mostly been explored using phenomenological models that simply link the subglacial erosion rate to sliding or ice discharge. In order to improve our understanding of the causal links between the glacial landforms and the physics of the subglacial environment, we have performed computational experiments with a higher-order ice sheet model (Egholm et al., 2009) capable of simulating the long-term evolution of subglacial dynamics at a high spatial resolution. The orientation and magnitude of subglacial stress components depend not only on ice thickness and ice surface gradients, but also on the details of the bed topography and the regional variations in ice flow velocity. As glaciers erode their beds and modify the morphology of glaciated valleys, the subglacial dynamics therefore change with important implications for the sliding patterns and the continued erosion rates. We focus this presentation on feedbacks between the evolving bed topography and the subglacial erosion patterns. We have performed our experiments with different sliding and erosion laws, including highly non-linear rules representing coulomb-type slip at the bed (Schoof, 2010) and a quarrying model associated to the level of cavitation (Iverson, 2012). The highly non-linear computational experiments are made possible by new and very efficient GPU-accelerated multigrid algorithms. The computational experiments show that higher-order stress effects associated with local changes to the bed gradient provide important stabilizing effects for example in overdeepenings and near topographic steps. The experiments also show how a narrow and meandering pre-glacial valley represents a much more stable environment for a glacier than a glacially eroded valley where slip instabilities can readily propagate upstream. References: Egholm, D. L. et al. Modeling the flow of glaciers in steep terrains: The integrated second-order shallow ice approximation (iSOSIA). Journal of Geophysical Research, 116, F02012 (2011). Iverson, N. R. A theory of glacial quarrying for landscape evolution models. Geology, v. 40, no. 8, 679-682 (2012). Schoof, C. The effect of cavitation on glacier sliding. Proc. R. Soc. A , 461, 609-627 (2005).

Feedbacks between subglacial dynamics and long-term glacial landscape evolution (Invited)

NASA Astrophysics Data System (ADS)

Brædstrup, C. F.; Egholm, D. L.; Ugelvig, S. V.; Christensen, A. D.; Andersen, J. L.

2013-12-01

Several well-known glacial landforms (such as U-shaped troughs and cirques) are associated with characteristic length scales, indicating that the viscosity of the ice and the stress gradients associated with ice flow exert first-order controls on their formation. The evolution of these glacial landforms has so far mostly been explored using phenomenological models that simply link the subglacial erosion rate to sliding or ice discharge. In order to improve our understanding of the causal links between the glacial landforms and the physics of the subglacial environment, we have performed computational experiments with a higher-order ice sheet model (Egholm et al., 2009) capable of simulating the long-term evolution of subglacial dynamics at a high spatial resolution. The orientation and magnitude of subglacial stress components depend not only on ice thickness and ice surface gradients, but also on the details of the bed topography and the regional variations in ice flow velocity. As glaciers erode their beds and modify the morphology of glaciated valleys, the subglacial dynamics therefore change with important implications for the sliding patterns and the continued erosion rates. We focus this presentation on feedbacks between the evolving bed topography and the subglacial erosion patterns. We have performed our experiments with different sliding and erosion laws, including highly non-linear rules representing coulomb-type slip at the bed (Schoof, 2010) and a quarrying model associated to the level of cavitation (Iverson, 2012). The highly non-linear computational experiments are made possible by new and very efficient GPU-accelerated multigrid algorithms. The computational experiments show that higher-order stress effects associated with local changes to the bed gradient provide important stabilizing effects for example in overdeepenings and near topographic steps. The experiments also show how a narrow and meandering pre-glacial valley represents a much more stable environment for a glacier than a glacially eroded valley where slip instabilities can readily propagate upstream. References: Egholm, D. L. et al. Modeling the flow of glaciers in steep terrains: The integrated second-order shallow ice approximation (iSOSIA). Journal of Geophysical Research, 116, F02012 (2011). Iverson, N. R. A theory of glacial quarrying for landscape evolution models. Geology, v. 40, no. 8, 679-682 (2012). Schoof, C. The effect of cavitation on glacier sliding. Proc. R. Soc. A , 461, 609-627 (2005).

Satellite observation of bio-optical indicators related to North-Western Black Sea coastal zone changes

NASA Astrophysics Data System (ADS)

Zoran, Maria

Satellite remote sensing provides a means for locating, identifying and mapping certain coastal zone features and assessing of spatio-temporal changes.The Romanian coastal zone of the Black Sea is a mosaic of complex, interacting ecosystems, exposed to dramatic changes due to natural and anthropogenic causes (increase in the nutrient and pollutant load of rivers input, industrial and municipal wastewater pollution along the coast, and dumping on the open sea). This study focuses on the assessment of coastal zone land cover changes based on the fusion of satellite remote sensing data.The evaluation of coastal zone landscapes is based upon different sub-functions which refer to landscape features such as water, soil, land-use, buildings, groundwater, biotope types. Mixed pixels result when the sensor's instantaneous field-of-view includes more than one land cover class on the ground. Based on different satellite data (Landsat TM, ETM, SAR ERS, IKONOS, Quickbird, and MODIS) was performed object recognition for North-Western Black Sea coastal zone. Preliminary results show significant coastline position changes of North Western Black Sea during the period of 1987-2007 and urban growth of Constantza town. Also the change in the position of the coastline is examined and linked to the urban expansion in order to determine if the changes are natural or anthropogenic. A distinction is made between landfill/sedimentation processes on the one hand and dredging/erosion processes on the other. Waves play an important role for shoreline configuration. Wave pattern could induce erosion and sedimentation. A quasi-linear model was used to model the rate of shoreline change. The vectors of shoreline were used to compare with wave spectra model in order to examine the accuracy of the coastal erosion model. The shoreline rate modeled from vectors data of SAR ERS-1 has a good correlation with a quasi-linear model. Wave refraction patterns are a good index for shoreline erosion. A coast-parallel wind drives the surface layer of water almost directly offshore. Removing the surface layer causes deeper water, with different characteristics (e.g. colder and with higher salinity), to upwell along the coast. The upwelling signal is strong influenced by the seasonal cycle, the upwelling effects have strong influence on the marine ecosystems, which are all localized in the first 100-200 m.

Rate of bedrock channel incision by waterfall retreat and landscape response constrained by cosmogenic 3He, Kauai, Hawaii

NASA Astrophysics Data System (ADS)

Mackey, B. H.; Lamb, M. P.; Scheingross, J. S.; Farley, K. A.

2011-12-01

Channel incision and knickpoint retreat are the drivers of landscape evolution, yet we are still challenged to quantify the rate and processes by which rivers cut into rock. The Napali Coast on the northwestern side of Kauai, Hawaii, has multiple linear channels incising >200 m into the shield volcano surface. The channels have well-constrained initial conditions, including original topography, and relatively uniform layered basalt of known age (~4.5 Ma), which have attracted previous studies of channel evolution (e.g., Seidl et al., 1994, 1997). Many channels feature prominent waterfalls, although the mechanism of knickpoint initiation (submarine landslide vs cliff erosion) and subsequent retreat remain ambiguous. Motivated by these knowledge gaps and recent advances in cosmogenic helium geochronology, we revisited the Kaulaula Valley, a 9 km long narrow valley, beheaded on its upslope extent by the Waimea Canyon, and ending near the coast at the northern Mana Plain. Four kilometers up the canyon is a prominent 40 m high vertical knickpoint, dividing the valley into strongly contrasting geomorphic domains. The boulder-lined channel below the knickpoint is linear, steep (15%), and confined to a narrow valley with steep rocky cliffs (average slope 31°). Large, >2 m diameter angular boulders in the lower section of channel show evidence of mobility from debris flows. Above the knickpoint, average channel gradient is reduced (9%), bed load is much finer, and convex, soil-mantled hillslopes have a consistently lower mean slope of 18°. We constrained the exposure age of 18 features (in-channel boulders, stable boulders on terraces, and in-channel bedrock) along the length of the channel, by analysis of cosmogenic 3He in olivine phenocrysts. Cosmogenic exposure ages are oldest near the coast (80 ka) and systematically decrease with upstream distance towards the waterfall (< 5ka). In the upper section of channel, cosmogenic ages are approximately constant (10-20 ka). This data supports the conceptual model of knickpoint retreat and downstream terrace abandonment advocated by Seidl (1997), and we can constrain a maximum retreat rate of 40 mm/yr. Steady state erosion appears to dominate upstream of the waterfall. Catchment averaged erosion rates from detrital olivine (assuming catchment averaged production rate) give an erosion rate of 0.04 mm/yr .

Preventive effects of different protective agents on dentin erosion: An in vitro investigation

PubMed Central

Gulino, Chiara; Mirando, Maria; Colombo, Marco; Pietrocola, Giampiero

2017-01-01

Background The purpose of this in vitro study was to evaluate the preventive effects of different protective agents on dentine erosion, measuring mean percentage weight loss. Dissolution of dentine under erosive challenges caused by soft drinks was analyzed: specimens were weighed following each immersion period, with mean percent weight losses calculated. Material and Methods Extracted teeth were sectioned into uniform slabs. Seventy permanent enamel specimens were randomly distributed to seven groups. Initial weights of all dentin specimens were performed. The fluoride pastes Remin Pro, MI Paste Plus, Tooth Mousse, Biorepair, Biorepair Plus and Regenerate were used in this study. A control group was treated just with tap water. The specimens then were immersed in Coca-Cola for a total of 32 min at room temperature. Finally each specimen was dry and weighed. The mass loss was calculated as a percentage of that observed prior the fluoride pastes application. Weight loss data were subjected to Analysis of Variance (One-way ANOVA) followed by Bonferroni’s post hoc tests. Results Percent weight loss of specimens exposed to early stages in Coca-Cola showed linear progression with time. Specimen’s application of fluoridated varnishes such as Biorepair or Regenerate, prior immersion in Coca-Cola, significantly protect dentin from demineralization. Otherwise, application of Tooth Mousse or Biorepair Plus increased dentin demineralization starting from 24 min of immersion in Coca-Cola. Conclusions Despite the limitations of this study, the protective pastes that showed the less weight loss due to the acidic challenge are Biorepair and Regenerate. Key words:Dentine, erosion, protective agents, soft drinks, toothpastes. PMID:28149456

Preventive effects of different protective agents on dentin erosion: An in vitro investigation.

PubMed

Poggio, Claudio; Gulino, Chiara; Mirando, Maria; Colombo, Marco; Pietrocola, Giampiero

2017-01-01

The purpose of this in vitro study was to evaluate the preventive effects of different protective agents on dentine erosion, measuring mean percentage weight loss. Dissolution of dentine under erosive challenges caused by soft drinks was analyzed: specimens were weighed following each immersion period, with mean percent weight losses calculated. Extracted teeth were sectioned into uniform slabs. Seventy permanent enamel specimens were randomly distributed to seven groups. Initial weights of all dentin specimens were performed. The fluoride pastes Remin Pro, MI Paste Plus, Tooth Mousse, Biorepair, Biorepair Plus and Regenerate were used in this study. A control group was treated just with tap water. The specimens then were immersed in Coca-Cola for a total of 32 min at room temperature. Finally each specimen was dry and weighed. The mass loss was calculated as a percentage of that observed prior the fluoride pastes application. Weight loss data were subjected to Analysis of Variance (One-way ANOVA) followed by Bonferroni's post hoc tests. Percent weight loss of specimens exposed to early stages in Coca-Cola showed linear progression with time. Specimen's application of fluoridated varnishes such as Biorepair or Regenerate, prior immersion in Coca-Cola, significantly protect dentin from demineralization. Otherwise, application of Tooth Mousse or Biorepair Plus increased dentin demineralization starting from 24 min of immersion in Coca-Cola. Despite the limitations of this study, the protective pastes that showed the less weight loss due to the acidic challenge are Biorepair and Regenerate. Key words: Dentine, erosion, protective agents, soft drinks, toothpastes.

The Significance of Land Cover Delineation on Soil Erosion Assessment.

PubMed

Efthimiou, Nikolaos; Psomiadis, Emmanouil

2018-04-25

The study aims to evaluate the significance of land cover delineation on soil erosion assessment. To that end, RUSLE (Revised Universal Soil Loss Equation) was implemented at the Upper Acheloos River catchment, Western Central Greece, annually and multi-annually for the period 1965-92. The model estimates soil erosion as the linear product of six factors (R, K, LS, C, and P) considering the catchment's climatic, pedological, topographic, land cover, and anthropogenic characteristics, respectively. The C factor was estimated using six alternative land use delineations of different resolution, namely the CORINE Land Cover (CLC) project (2000, 2012 versions) (1:100,000), a land use map conducted by the Greek National Agricultural Research Foundation (NAGREF) (1:20,000), a land use map conducted by the Greek Payment and Control Agency for Guidance and Guarantee Community Aid (PCAGGCA) (1:5,000), and the Landsat 8 16-day Normalized Difference Vegetation Index (NDVI) dataset (30 m/pixel) (two approximations) based on remote sensing data (satellite image acquired on 07/09/2016) (1:40,000). Since all other factors remain unchanged per each RUSLE application, the differences among the yielded results are attributed to the C factor (thus the land cover pattern) variations. Validation was made considering the convergence between simulated (modeled) and observed sediment yield. The latter was estimated based on field measurements conducted by the Greek PPC (Public Power Corporation). The model performed best at both time scales using the Landsat 8 (Eq. 13) dataset, characterized by a detailed resolution and a satisfactory categorization, allowing the identification of the most susceptible to erosion areas.

Coastal erosion hazard and vulnerability using sig tools. Comparison between "La Barra town, Buenaventura, (Pacific Ocean of Colombia) and Providence - Santa Catalina islands (Colombian Caribbean Sea)

NASA Astrophysics Data System (ADS)

Coca-Domínguez, Oswaldo; Ricaurte-Villota, Constanza; Morales-Giraldo, David; Rangel-Buitrago, Nelson

2014-05-01

Analysis of hazards and vulnerability associated to coastal erosion along coastlines is a first issue in order to establish plans for adaptation to climate change in coastal areas. La Barra Town, Buenaventura (Pacific ocean of Colombia) and Providence - Santa Catalina Islands (Colombian Caribbean) were selected to develop a detailed analysis of coastal erosion hazard and vulnerability from different perspectives: i) physical (hazard) , ii) social , iii) conservation approach and iv) cultural heritage (Raizal). The analysis was made by a semi quantitative approximation method, applying variables associated with the intrinsic coastal zone properties (i.e. type of beach, exposure of the coast to waves, etc.). Coastal erosion data and associated variables as well land use; conservation and heritage data were used to carry out a further detailed analysis of the human - structural vulnerability and exposure to hazards. The data shows erosion rates close to -17 m yr-1 in La Barra Town (highlighting their critical condition and urgent relocation process), while in some sectors of Providence Island, such as Old Town, erosion rate was -5 m yr-1. The observed erosion process affects directly the land use and the local and regional economy. The differences between indexes and the structural and physical vulnerability as well the use of methodological variables are presented in the context of each region. In this work, all the information was worked using a GIS environment since this allows editing and updating the information continuously. The application of this methodology generates useful information in order to promote risk management as well prevention, mitigation and reduction plans. In both areas the adaptation must be a priority strategy to be considered, including relocation alternatives and sustainable protection with the support of studies of uses and future outlooks in the coast. The methodology is framed into the use of GIS tools and it highlights their benefits in the analysis of information.

Land use and climate change impacts on runoff and soil erosion at the hillslope scale in the Brazilian Cerrado.

PubMed

Anache, Jamil A A; Flanagan, Dennis C; Srivastava, Anurag; Wendland, Edson C

2018-05-01

Land use and climate change can influence runoff and soil erosion, threatening soil and water conservation in the Cerrado biome in Brazil. The adoption of a process-based model was necessary due to the lack of long-term observed data. Our goals were to calibrate the WEPP (Water Erosion Prediction Project) model for different land uses under subtropical conditions in the Cerrado biome; predict runoff and soil erosion for these different land uses; and simulate runoff and soil erosion considering climate change. We performed the model calibration using a 5-year dataset (2012-2016) of observed runoff and soil loss in four different land uses (wooded Cerrado, tilled fallow without plant cover, pasture, and sugarcane) in experimental plots. Selected soil and management parameters were optimized for each land use during the WEPP model calibration with the existing field data. The simulations were conducted using the calibrated WEPP model components with a 100-year climate dataset created with CLIGEN (weather generator) based on regional climate statistics. We obtained downscaled General Circulation Model (GCM) projections, and runoff and soil loss were predicted with WEPP using future climate scenarios for 2030, 2060, and 2090 considering different Representative Concentration Pathways (RCPs). The WEPP model had an acceptable performance for the subtropical conditions. Land use can influence runoff and soil loss rates in a significant way. Potential climate changes, which indicate the increase of rainfall intensities and depths, may increase the variability and rates of runoff and soil erosion. However, projected climate changes did not significantly affect the runoff and soil erosion for the four analyzed land uses at our location. Finally, the runoff behavior was distinct for each land use, but for soil loss we found similarities between pasture and wooded Cerrado, suggesting that the soil may attain a sustainable level when the land management follows conservation principles. Copyright © 2017 Elsevier B.V. All rights reserved.

Influence of Threshold for Bedrock Erosion on River Long Profile Development and Knickzone Retreat in Response to Tectonic Perturbation

NASA Astrophysics Data System (ADS)

Attal, M.; Hobley, D.; Cowie, P. A.; Whittaker, A. C.; Tucker, G. E.; Roberts, G. P.

2008-12-01

Prominent convexities in channel long profiles, or knickzones, are an expected feature of bedrock rivers responding to a change in the rate of base level fall driven by tectonic processes. In response to a change in relative uplift rate, the simple stream power model which is characterized by a slope exponent equal to unity predicts that knickzone retreat velocity is independent of uplift rate and that channel slope and uplift rate are linearly related along the reaches which have re-equilibrated with respect to the new uplift condition (i.e., downstream of the profile convexity). However, a threshold for erosion has been shown to introduce non- linearity between slope and uplift rate when associated with stochastic rainfall variability. We present field data regarding the height and retreat rates of knickzones in rivers upstream of active normal faults in the central Apennines, Italy, where excellent constraints exist on the temporal and spatial history of fault movement. The knickzones developed in response to an independently-constrained increase in fault throw rate 0.75 Ma. Channel characteristics and Shield stress values suggest that these rivers lie close to the detachment-limited end-member but the knickzone retreat velocity (calculated from the time since fault acceleration) has been found to scale systematically with the known fault throw rates, even after accounting for differences in drainage area. In addition, the relationship between measured channel slope and relative uplift rate is non-linear, suggesting that a threshold for erosion might be effective in this setting. We use the Channel-Hillslope Integrated Landscape Development (CHILD) model to quantify the effect of such a threshold on river long profile development and knickzone retreat in response to tectonic perturbation. In particular, we investigate the evolutions of 3 Italian catchments of different size characterized by contrasted degree of tectonic perturbation, using physically realistic threshold values based on sediment grain-size measurements along the studied rivers. We show that the threshold alone cannot account for field observations of the size, position and retreat rate of profile convexities and that other factors neglected by the simple stream power law (e.g. role of sediments) have to be invoked to explain the discrepancy between field observations and modeled topographies.

Soil erosion and sediment yield, a double barrel problem in South Africa's only large river network without a dam

NASA Astrophysics Data System (ADS)

Le Roux, Jay

2016-04-01

Soil erosion not only involves the loss of fertile topsoil but is also coupled with sedimentation of dams, a double barrel problem in semi-arid regions where water scarcity is frequent. Due to increasing water requirements in South Africa, the Department of Water and Sanitation is planning water resource development in the Mzimvubu River Catchment, which is the only large river network in the country without a dam. Two dams are planned including a large irrigation dam and a hydropower dam. However, previous soil erosion studies indicate that large parts of the catchment is severely eroded. Previous studies, nonetheless, used mapping and modelling techniques that represent only a selection of erosion processes and provide insufficient information about the sediment yield. This study maps and models the sediment yield comprehensively by means of two approaches over a five-year timeframe between 2007 and 2012. Sediment yield contribution from sheet-rill erosion was modelled with ArcSWAT (a graphical user interface for SWAT in a GIS), whereas gully erosion contributions were estimated using time-series mapping with SPOT 5 imagery followed by gully-derived sediment yield modelling in a GIS. Integration of the sheet-rill and gully results produced a total sediment yield map, with an average of 5 300 t km-2 y-1. Importantly, the annual average sediment yield of the areas where the irrigation dam and hydropower dam will be built is around 20 000 t km-2 y-1. Without catchment rehabilitation, the life expectancy of the irrigation dam and hydropower dam could be 50 and 40 years respectively.

Modeling erosion and sedimentation coupled with hydrological and overland flow processes at the watershed scale

NASA Astrophysics Data System (ADS)

Kim, Jongho; Ivanov, Valeriy Y.; Katopodes, Nikolaos D.

2013-09-01

A novel two-dimensional, physically based model of soil erosion and sediment transport coupled to models of hydrological and overland flow processes has been developed. The Hairsine-Rose formulation of erosion and deposition processes is used to account for size-selective sediment transport and differentiate bed material into original and deposited soil layers. The formulation is integrated within the framework of the hydrologic and hydrodynamic model tRIBS-OFM, Triangulated irregular network-based, Real-time Integrated Basin Simulator-Overland Flow Model. The integrated model explicitly couples the hydrodynamic formulation with the advection-dominated transport equations for sediment of multiple particle sizes. To solve the system of equations including both the Saint-Venant and the Hairsine-Rose equations, the finite volume method is employed based on Roe's approximate Riemann solver on an unstructured grid. The formulation yields space-time dynamics of flow, erosion, and sediment transport at fine scale. The integrated model has been successfully verified with analytical solutions and empirical data for two benchmark cases. Sensitivity tests to grid resolution and the number of used particle sizes have been carried out. The model has been validated at the catchment scale for the Lucky Hills watershed located in southeastern Arizona, USA, using 10 events for which catchment-scale streamflow and sediment yield data were available. Since the model is based on physical laws and explicitly uses multiple types of watershed information, satisfactory results were obtained. The spatial output has been analyzed and the driving role of topography in erosion processes has been discussed. It is expected that the integrated formulation of the model has the promise to reduce uncertainties associated with typical parameterizations of flow and erosion processes. A potential for more credible modeling of earth-surface processes is thus anticipated.

Optical Diagnostic Characterization of High-Power Hall Thruster Wear and Operation

NASA Technical Reports Server (NTRS)

Williams, George J., Jr.; Soulas, George C.; Kamhawi, Hani

2012-01-01

Optical emission spectroscopy is employed to correlate BN insulator erosion with high-power Hall thruster operation. Specifically, actinometry leveraging excited xenon states is used to normalize the emission spectra of ground state boron as a function of thruster operating condition. Trends in the strength of the boron signal are correlated with thruster power, discharge voltage, and discharge current. In addition, the technique is demonstrated on metallic coupons embedded in the walls of the HiVHAc EM thruster. The OES technique captured the overall trend in the erosion of the coupons which boosts credibility in the method since there are no data to which to calibrate the erosion rates of high-power Hall thrusters. The boron signals are shown to trend linearly with discharge voltage for a fixed discharge current as expected. However, the boron signals of the higher-power NASA 300M and NASA 457Mv2 trend with discharge current and show an unexpectedly weak to inverse dependence on discharge voltage. Electron temperatures measured optically in the near-field plume of the thruster agree well with Langmuir probe data. However, the optical technique used to determine Te showed unacceptable sensitivity to the emission intensities. Near-field, single-frequency imaging of the xenon neutrals is also presented as a function of operating condition for the NASA 457 Mv2.

Modes of Disintegration of Solid Foods in Simulated Gastric Environment

PubMed Central

Kong, Fanbin

2009-01-01

A model stomach system was used to investigate disintegration of various foods in simulated gastric environment. Food disintegration modes and typical disintegration profiles are summarized in this paper. Mechanisms contributing to the disintegration kinetics of different foods were investigated as related to acidity, temperature, and enzymatic effect on the texture and changes in microstructure. Food disintegration was dominated by either fragmentation or erosion, depending on the physical forces acting on food and the cohesive force within the food matrix. The internal cohesive forces changed during digestion as a result of water penetration and acidic and enzymatic hydrolysis. When erosion was dominant, the disintegration data (weight retention vs. disintegration time) may be expressed with exponential, sigmoidal, and delayed-sigmoidal profiles. The different profiles are the result of competition among the rates of water absorption, texture softening, and erosion. A linear-exponential equation was used to describe the different disintegration curves with good fit. Acidity and temperature of gastric juice showed a synergistic effect on carrot softening, while pepsin was the key factor in disintegrating high-protein foods. A study of the change of carrot microstructure during digestion indicated that degradation of the pectin and cell wall was responsible for texture softening that contributed to the sigmoidal profile of carrot disintegration. PMID:20401314

Hydrologic analysis for selection and placement of conservation practices at the watershed scale

NASA Astrophysics Data System (ADS)

Wilson, C.; Brooks, E. S.; Boll, J.

2012-12-01

When a water body is exceeding water quality standards and a Total Maximum Daily Load has been established, conservation practices in the watershed are able to reduce point and non-point source pollution. Hydrological analysis is needed to place conservation practices in the most hydrologically sensitive areas. The selection and placement of conservation practices, however, is challenging in ungauged watersheds with little or no data for the hydrological analysis. The objective of this research is to perform a hydrological analysis for mitigation of erosion and total phosphorus in a mixed land use watershed, and to select and place the conservation practices in the most sensitive areas. The study area is the Hangman Creek watershed in Idaho and Washington State, upstream of Long Lake (WA) reservoir, east of Spokane, WA. While the pollutant of concern is total phosphorus (TP), reductions in TP were translated to total suspended solids or reductions in nonpoint source erosion and sediment delivery to streams. Hydrological characterization was done with a simple web-based tool, which runs the Water Erosion Prediction Project (WEPP) model for representative land types in the watersheds, where a land type is defined as a unique combination of soil type, slope configuration, land use and management, and climate. The web-based tool used site-specific spatial and temporal data on land use, soil physical parameters, slope, and climate derived from readily available data sources and provided information on potential pollutant pathways (i.e. erosion, runoff, lateral flow, and percolation). Multiple land types representative in the watershed were ordered from most effective to least effective, and displayed spatially using GIS. The methodology for the Hangman Creek watershed was validated in the nearby Paradise Creek watershed that has long-term stream discharge and monitoring as well as land use data. Output from the web-based tool shows the potential reductions for different tillage practices, buffer strips, streamside management, and conversion to the conservation reserve program in the watershed. The output also includes the relationship between land area where conservation practices are placed and the potential reduction in pollution, showing the diminished returns on investment as less sensitive areas are being treated. This application of a simple web-based tool and the use of a physically-based erosion model (i.e. WEPP) illustrates that quantitative, spatial and temporal analysis of changes in pollutant loading and site-specific recommendations of conservation practices can be made in ungauged watersheds.

Phosphorus load to surface water from bank erosion in a Danish lowland river basin.

PubMed

Kronvang, Brian; Audet, Joachim; Baattrup-Pedersen, Annette; Jensen, Henning S; Larsen, Søren E

2012-01-01

Phosphorus loss from bank erosion was studied in the catchment of River Odense, a lowland Danish river basin, with the aim of testing the hypothesis of whether stream banks act as major diffuse phosphorus (P) sources at catchment scale. Furthermore, the study aimed at analyzing the impact of different factors influencing bank erosion and P loss such as stream order, anthropogenic disturbances, width of uncultivated buffer strips, and the vegetation of buffer strips. A random stratified procedure in geographical information system (GIS) was used to select two replicate stream reaches covering different stream orders, channelized vs. naturally meandering channels, width of uncultivated buffer strips (≤ 2 m and ≥ 10 m), and buffer strips with different vegetation types. Thirty-six 100-m stream reaches with 180 bank plots and a total of 3000 erosion pins were established in autumn 2006, and readings were conducted during a 3-yr period (2006-2009). The results show that neither stream size nor stream disturbance measured as channelization of channel or the width of uncultivated buffer strip had any significant ( < 0.05) influence on bank erosion and P losses during each of the 3 yr studied. In buffer strips with natural trees bank erosion was significantly ( < 0.05) lower than in buffer strips dominated by grass and herbs. Gross and net P input from bank erosion amounted to 13.8 to 16.5 and 2.4 to 6.3 t P, respectively, in the River Odense catchment during the three study years. The net P input from bank erosion equaled 17 to 29% of the annual total P export and 21 to 62% of the annual export of P from diffuse sources from the River Odense catchment. Most of the exported total P was found to be bioavailable (71.7%) based on a P speciation of monthly suspended sediment samples collected at the outlet of the river basin. The results found in this study have a great importance for managers working with P mitigation and modeling at catchment scale. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

Selection criteria for wear resistant powder coatings under extreme erosive wear conditions

NASA Astrophysics Data System (ADS)

Kulu, P.; Pihl, T.

2002-12-01

Wear-resistant thermal spray coatings for sliding wear are hard but brittle (such as carbide and oxide based coatings), which makes them useless under impact loading conditions and sensitive to fatigue. Under extreme conditions of erosive wear (impact loading, high hardness of abrasives, and high velocity of abradant particles), composite coatings ensure optimal properties of hardness and toughness. The article describes tungsten carbide-cobalt (WC-Co) systems and self-fluxing alloys, containing tungsten carbide based hardmetal particles [NiCrSiB-(WC-Co)] deposited by the detonation gun, continuous detonation spraying, and spray fusion processes. Different powder compositions and processes were studied, and the effect of the coating structure and wear parameters on the wear resistance of coatings are evaluated. The dependence of the wear resistance of sprayed and fused coatings on their hardness is discussed, and hardness criteria for coating selection are proposed. The so-called “double cemented” structure of WC-Co based hardmetal or metal matrix composite coatings, as compared with a simple cobalt matrix containing particles of WC, was found optimal. Structural criteria for coating selection are provided. To assist the end user in selecting an optimal deposition method and materials, coating selection diagrams of wear resistance versus hardness are given. This paper also discusses the cost-effectiveness of coatings in the application areas that are more sensitive to cost, and composite coatings based on recycled materials are offered.

Evidence of anthropogenic tipping points in fluvial dynamics in Europe

NASA Astrophysics Data System (ADS)

Notebaert, Bastiaan; Broothaerts, Nils; Verstraeten, Gert

2018-05-01

In this study the occurrence of thresholds in fluvial style changes during the Holocene are discussed for three different catchments: the Dijle and Amblève catchments (Belgium) and the Valdaine Region (France). We consider tipping points to be a specific type of threshold, defined as relatively rapid and irreversible changes in the system. Field data demonstrate that fluvial style has varied in all three catchments over time, and that different tipping points can be identified. An increase in sediment load as a result of human induced soil erosion lead to a permanent change in the Dijle floodplains from a forested peaty marsh towards open landscape with clastic deposition and a well-defined river channel. In the Valdaine catchment, an increase in coarse sediment load, caused by increased erosion in the mountainous upper catchment, altered the floodplains from a meandering pattern to a braided pattern. Other changes in fluvial style appeared to be reversible. Rivers in the Valdaine were prone to different aggradation and incision phases due to changes in peak water discharge and sediment delivery, but the impact was too low for these changes to be irreversible. Likewise the Dijle River has recently be prone to an incision phase due to a clear water effect, and also this change is expected to be reversible. Finally, the Amblève River did not undergo major changes in style during the last 2000 to 5000 years, even though floodplain sedimentation rates increased tenfold during the last 600 years. Overall, these examples demonstrate how changes in fluvial style depend on the crossing of thresholds in sediment supply and water discharge. Although changes in these controlling parameters are caused by anthropogenic land use changes, the link between those land use changes and changes in fluvial style is not linear. This is due to the temporal variability in landscape connectivity and sediment transport and the non-linear relationship between land use intensity and soil erosion.

Materials International Space Station Experiment-6 (MISSE-6) Atomic Oxygen Fluence Monitor Experiment

NASA Technical Reports Server (NTRS)

Banks, Bruce A.; Miller, Sharon K.; Waters, Deborah L.

2010-01-01

An atomic oxygen fluence monitor was flown as part of the Materials International Space Station Experiment-6 (MISSE-6). The monitor was designed to measure the accumulation of atomic oxygen fluence with time as it impinged upon the ram surface of the MISSE 6B Passive Experiment Container (PEC). This was an active experiment for which data was to be stored on a battery-powered data logger for post-flight retrieval and analysis. The atomic oxygen fluence measurement was accomplished by allowing atomic oxygen to erode two opposing wedges of pyrolytic graphite that partially covered a photodiode. As the wedges of pyrolytic graphite erode, the area of the photodiode that is illuminated by the Sun increases. The short circuit current, which is proportional to the area of illumination, was to be measured and recorded as a function of time. The short circuit current from a different photodiode, which was oriented in the same direction and had an unobstructed view of the Sun, was also to be recorded as a reference current. The ratio of the two separate recorded currents should bear a linear relationship with the accumulated atomic oxygen fluence and be independent of the intensity of solar illumination. Ground hyperthermal atomic oxygen exposure facilities were used to evaluate the linearity of the ratio of short circuit current to the atomic oxygen fluence. In flight, the current measurement circuitry failed to operate properly, thus the overall atomic oxygen mission fluence could only be estimated based on the physical erosion of the pyrolytic graphite wedges. The atomic oxygen fluence was calculated based on the knowledge of the space atomic oxygen erosion yield of pyrolytic graphite measured from samples on the MISSE 2. The atomic oxygen fluence monitor, the expected result and comparison of mission atomic oxygen fluence based on the erosion of the pyrolytic graphite and Kapton H atomic oxygen fluence witness samples are presented in this paper.

[A field experiment of runoff and sediment yielding processes from residues in Shenfu-Dongsheng Coalfield].

PubMed

Li, Jian-Ming; Wang, Wen-Long; Wang, Zhen; Luo, Ting; Li, Hong-Wei; Jin, Jian

2013-12-01

The processes of runoff and sediment yields from and the benefits of water and sediment reductions by the residues produced in the Shenfu-Dongsheng Coalfield were investigated by a simulated field rainfall experiment. The runoff generation time generally presented a decreasing trend with increasing rainfall intensity, but varied widely with the change of residue compositions. Runoff from the slag reached a steady velocity faster than that from the spoil, and the average velocities of runoff from the residues were gradually decreased in the spoil, the slag with more sand and less stone, and the slag with less sand and more stone. Runoff rates for the residues reached a steady rate 6 min after runoff generation, and were significantly correlated with the rainfall intensities. Erosion on the residues mainly occurred in the first 6 min after runoff generation. Average sediment concentrations in the first 6 min were 0.43-4.27 times of those thereafter for the spoil, and 1.43-54.93 times for the slag. The runoff volume was a linear function of the rainfall intensity for the spoil and the slag with more sand and less stone, and was a power function of rainfall intensity for the slag with less sand and more stone. The relationships between single erosion and rainfall intensity for the spoil and the slag with less sand and more stone can be described by exponential and power functions, respectively. For the spoil, the erosion rate was a linear function of the runoff volume. When fish-scale pits and vegetation coverage were adopted on the surface of the slag, the generation of runoff lagged 24 min behind initial rainfall applications at intensities of 1.0 and 1.5 mm x min(-1), and the runoff and sediment yields were reduced by 29.5%-52.9% and 85.7%-97.9%, respectively.

Intensification of citrus production and soil loss in Eastern Spain

NASA Astrophysics Data System (ADS)

Cerdà, A.; González Peñaloza, F. A.; Burguet, M.; Giménez Morera, A.

2012-04-01

After land abandonment for five decades (Arnáez et al., 2010; Belmonte Serrato et al., 1999) as a widespread process in Spain, agriculture intensification is taken place. This is changing the nature of the soil erosion processes as they were known (Cerdà, 1997; Cammeraat and Imeson, 1999; Ruiz Sinoga et al., 2010; Zavala et al., 2010). Citrus production are being reallocated on slopes due to the new irrigation systems (drip-irrigation), the thermic inversion on the bottom of the valley and then the frost affecting the plantations, the high prices of the bottom valley lands and the investment in agriculture from other economic sectors such as tourism and industry. Those new plantations are based on intense pesticides and herbicides use, and erosion processes are triggered due to the sloping surface developed (Cerdà et al., 2010). Five study sites were selected in the Montesa Municipality research zone, where an increase in the orange and clementines plantations were found during the last 20 years. Measurements were perfomed by a simple method, which consist in measuring the surface characteristics: stoniness, crust, herbs, bare soil, sheet flow, rills and gullies. One thousand meters were monitored at each of the study sites and measurements were done in January and August with a precision of 1 cm. The results show that the erosion rates are controlled by the sheet erosion (78,4 %), although rill and gullies exist (< 1 %) and they are active and contribute to high erosion rates. Stones and vegetation cover was found to by low. The infiltration rates of the soils were measured by means of rainfall simulation experiments and cylinder infiltrometer. The results show that the new citrus plantations results in low infiltration rates, and high erosion rates. This is contributing to a non-sustainable agriculture production due to the high erosion rates. And also a lack in soil services as the surface runoff and then the soil erosion is enhanced; and soil infiltration reduce. The economical value of the land and water lost is making this new intense chemically managed new citrus plantation non sustainable. The intensification of agriculture is triggering new soil erosion processes to be added to the traditional ones (García Ruiz and López Bermúdez, 2009). This research study is being supported by the the research project CGL2008-02879/BTE

Process based modelling of soil organic carbon redistribution on landscape scale

NASA Astrophysics Data System (ADS)

Schindewolf, Marcus; Seher, Wiebke; Amorim, Amorim S. S.; Maeso, Daniel L.; Jürgen, Schmidt

2014-05-01

Recent studies have pointed out the great importance of erosion processes in global carbon cycling. Continuous erosion leads to a massive loss of top soils including the loss of organic carbon accumulated over long time in the soil humus fraction. Lal (2003) estimates that 20% of the organic carbon eroded with top soils is emitted into atmosphere, due to aggregate breakdown and carbon mineralization during transport by surface runoff. Furthermore soil erosion causes a progressive decrease of natural soil fertility, since cation exchange capacity is associated with organic colloids. As a consequence the ability of soils to accumulate organic carbon is reduced proportionately to the drop in soil productivity. The colluvial organic carbon might be protected from further degradation depending on the depth of the colluvial cover and local decomposing conditions. Some colluvial sites can act as long-term sinks for organic carbon. The erosional transport of organic carbon may have an effect on the global carbon budget, however, it is uncertain, whether erosion is a sink or a source for carbon in the atmosphere. Another part of eroded soils and organic carbon will enter surface water bodies and might be transported over long distances. These sediments might be deposited in the riparian zones of river networks. Erosional losses of organic carbon will not pass over into atmosphere for the most part. But soil erosion limits substantially the potential of soils to sequester atmospheric CO2 by generating humus. The present study refers to lateral carbon flux modelling on landscape scale using the process based EROSION 3D soil loss simulation model, using existing parameter values. The selective nature of soil erosion results in a preferentially transport of fine particles while less carbonic larger particles remain on site. Consequently organic carbon is enriched in the eroded sediment compared to the origin soil. For this reason it is essential that EROSION 3D provides the grain size distribution (clay, silt and sand) of the transported sediment. A test slope is modeled covering certain land use and soil management scenarios referring to different rainfall events. Results allow first insights on carbon loss and depletion on sediment delivery areas as well as carbon gains and enrichments on deposition areas on landscape scale. Lal, R. (2003). Soil erosion and the global carbon budget. Environment International vol. 29: 437-450.

Analysis of Decadal-Scale Shoreline Change along the Hamlet of Paulatuk (Canadian Arctic), using Landsat Satellite Imagery and GIS techniques from 1984 to 2014.

NASA Astrophysics Data System (ADS)

Sankar, R. D.; Murray, M. S.; Wells, P.

2016-12-01

Increased accuracy in estimating coastal change along localized segments of the Canadian Arctic coast is essential, in order to identify plausible adaptation initiatives to deal with the effects of climate change. This paper quantifies rates of shoreline movement along an 11 km segment of the Hamlet of Paulatuk (Northwest Territories, Canada), using an innovative modelling technique - Analyzing Moving Boundaries Using R (AMBUR). Approximately two dozen shorelines, obtained from high-resolution Landsat satellite imagery were analyzed. Shorelines were extracted using the band ratio method and compiled in ArcMapTM to determine decadal trends of coastal change. The unique geometry of Paulatuk facilitated an independent analysis of the western and eastern sections of the study area. Long-term (1984-2014) and short-term (1984-2003) erosion and accretion rates were calculated using the Linear Regression and End Point Rate methods respectively. Results reveal an elevated rate of erosion for the western section of the hamlet over the long-term (-1.1 m/yr), compared to the eastern portion (-0.92 m/yr). The study indicates a significant alongshore increase in the rates of erosion on both portions of the study area, over the short-term period 1984 to 2003. Mean annual erosion rates increased over the short-term along the western segment (-1.4 m/yr), while the eastern shoreline retreated at a rate of -1.3 m/yr over the same period. The analysis indicates that an amalgamation of factors may be responsible for the patterns of land loss experienced along Paulatuk. These include increased sea-surface temperature coupled with dwindling arctic ice and elevated storm hydrodynamics. The analysis further reveals that the coastline along the eastern portion of the hamlet, where the majority of the population reside, is vulnerable to a high rate of shoreline erosion.

Natural change and human impact in a present-day fluvial catchment: The Geul River, Southern Netherlands

NASA Astrophysics Data System (ADS)

Vandenberghe, J.; de Moor, J. J. W.; Spanjaard, G.

2012-07-01

The Geul River has a long history of channel straightening and bank protection, but also has several natural meandering parts. In addition, some formerly 'fixed' or 'protected' stretches of the river have been allowed to meander freely since 1988. Therefore, it represents an ideal case for evaluating the contribution of human interference to the intrinsic evolution of the river. In this paper, we compare the response of selected (not protected) reaches of the present-day river to different human modifications. The river banks were labelled as "stable", "unstable" or "erosive". As might be expected, stretches with a high sinuosity have a high percentage of erosive and unstable bank length, while low-sinuosity stretches experience hardly any erosion. The amount of lateral erosion and sedimentation in natural situations is compared with that in situations with different bank protection and stabilization types. Erosion rates may locally attain up to 2 m per year. Detailed grain-size analysis of point-bar sections enable distinction of successive fining-up sequences. Vertical aggradation rates within the point-bars are up to 0.15 m yr- 1. The highest rates are found in the youngest point-bars. Collectively, the results of this study show that when bank protection is removed, the freely meandering river creates its own specific ecosystems and retention capacity increases. Such a return to natural environmental and ecological conditions is in accordance with the objectives of the European Water Framework Directive.

Using Computational Fluid Dynamics to Compare Shear Rate and Turbulence in the TIM-Automated Gastric Compartment With USP Apparatus II.

PubMed

Hopgood, Matthew; Reynolds, Gavin; Barker, Richard

2018-03-30

We use computational fluid dynamics to compare the shear rate and turbulence in an advanced in vitro gastric model (TIMagc) during its simulation of fasted state Migrating Motor Complex phases I and II, with the United States Pharmacopeia paddle dissolution apparatus II (USPII). A specific focus is placed on how shear rate in these apparatus affects erosion-based solid oral dosage forms. The study finds that tablet surface shear rates in TIMagc are strongly time dependant and fluctuate between 0.001 and 360 s -1 . In USPII, tablet surface shear rates are approximately constant for a given paddle speed and increase linearly from 9 s -1 to 36 s -1 as the paddle speed is increased from 25 to 100 rpm. A strong linear relationship is observed between tablet surface shear rate and tablet erosion rate in USPII, whereas TIMagc shows highly variable behavior. The flow regimes present in each apparatus are compared to in vivo predictions using Reynolds number analysis. Reynolds numbers for flow in TIMagc lie predominantly within the predicted in vivo bounds (0.01-30), whereas Reynolds numbers for flow in USPII lie above the predicted upper bound when operating with paddle speeds as low as 25 rpm (33). Copyright © 2018 American Pharmacists Association®. Published by Elsevier Inc. All rights reserved.

Impact of weather and climate scenarios on conservation assessment outcomes

USDA-ARS?s Scientific Manuscript database

This paper reviews selected watershed studies of the Conservation Effects Assessment Project (CEAP) and interprets findings from the perspective of potential climate change impacts on conservation outcomes. Primary foci are runoff, soil erosion, sediment transport, watershed sediment yield, and asso...

Potential-scour assessments and estimates of maximum scour at selected bridges in Iowa

USGS Publications Warehouse

Fischer, E.E.

1995-01-01

Although the abutment-scour equation predicted deep scour holes at many of the sites, the only significant abutment scour that was measured was erosion of the embankment at the left abutment at one bridge after a flood.

VDOT manual of practice for planning stormwater management.

DOT National Transportation Integrated Search

1992-01-01

The final report is in the form of a manual of practice for the VDOT to use in planning its stormwater management strategies. The manual was proposed to aid in the selection and design of erosion control practices and stormwater control practices for...

Adaptation to heavy rainfall events: watershed-community planning of soil and water conservation technologies in Syria

NASA Astrophysics Data System (ADS)

Ziadat, Feras; Al-Wadaey, Ahmed; Masri, Zuhair; Sakai, Hirokazu

2010-05-01

The Fourth Assessment Report of the Intergovernmental Panel on Climate Change (IPCC) and other research, predict a significant future increase in the frequency and intensity of heavy rainfall events in many regions. This increase runoff and soil erosion, and reduce agricultural productivity, as well as increasing risks of flood damage to crops and infrastructure. Implementing adaptation measures and improved land management through erosion control and soil protection are among those that protect water and agriculture and limit their vulnerability. Soil erosion control practices are often based on long-term climatic averages. Special attention is needed to provide protection against average high-return frequency storms as well as severe storms with low-return frequency. Suitable and affordable soil conservation plans, coupled with an appropriate enabling environment, are needed. A watershed and community were selected in the mountainous area of North West Syria. The fields represent the non-tropical highland dry areas and dominated by olive orchards on steep slopes. Farmers were aware of resource degradation and productivity reduction, but lacked financial capital to implement the needed adaptation measures. A micro-credit system was established with the help of the UNDP Global Environment Facility - Small Grants Program (GEF-SGP) with small grants available for each farmer. Haphazard implementation on scattered fields proved inefficient in demonstrating obvious impact. Therefore, each watershed was classified into three erosion risk categories (high, moderate and low), derived from maps of flow accumulation, slope steepness, slope shape and land use. Using field survey of land ownership, the boundaries of 168 farms in the watersheds were mapped. Farmers' fields were classified using the erosion-risk map and considering the on-farm erosion hazard and the off-farm effect on other farmers' fields following the hillslope sequence. More than 60% of the farms were classified into high erosion risk areas. Accordingly, a community-watershed plan was established and revised with the community committee. Loans to implement soil and water conservation measures were distributed to 52 farmers based on the priorities of their farms. Results from four runoff events in 2009 showed that one erosive runoff event can deliver more than 50% of the total soil loss. Implementing semi-circular bunds reduced rill erosion by 40% and captured 3.4 tons of sediments per hectare. The effect of this approach in limiting the negative impact of extreme rainfall events, at watershed and field levels, are now being quantified and modeled. Keywords: climate change, land use, soil erosion, GIS, flow accumulation, land tenure.

Sensitivity Analysis of the USLE Soil Erodibility Factor to Its Determining Parameters

NASA Astrophysics Data System (ADS)

Mitova, Milena; Rousseva, Svetla

2014-05-01

Soil erosion is recognized as one of the most serious soil threats worldwide. Soil erosion prediction is the first step in soil conservation planning. The Universal Soil Loss Equation (USLE) is one of the most widely used models for soil erosion predictions. One of the five USLE predictors is the soil erodibility factor (K-factor), which evaluates the impact of soil characteristics on soil erosion rates. Soil erodibility nomograph defines K-factor depending on soil characteristics, such as: particle size distribution (fractions finer that 0.002 mm and from 0.1 to 0.002 mm), organic matter content, soil structure and soil profile water permeability. Identifying the soil characteristics, which mostly influence the K-factor would give an opportunity to control the soil loss through erosion by controlling the parameters, which reduce the K-factor value. The aim of the report is to present the results of analysis of the relative weight of these soil characteristics in the K-factor values. The relative impact of the soil characteristics on K-factor was studied through a series of statistical analyses of data from the geographic database for soil erosion risk assessments in Bulgaria. Degree of correlation between K-factor values and the parameters that determine it was studied by correlation analysis. The sensitivity of the K-factor was determined by studying the variance of each parameter within the range between minimum and maximum possible values considering average value of the other factors. Normalizing transformation of data sets was applied because of the different dimensions and the orders of variation of the values of the various parameters. The results show that the content of particles finer than 0.002 mm has the most significant relative impact on the soil erodibility, followed by the content of particles with size from 0.1 mm to 0.002 mm, the class of the water permeability of the soil profile, the content of organic matter and the aggregation class. The relationships of the K-factor with the relative content of particle size from 0.1 to 0.002 mm and the class of aggregation are linear, directly proportional. When the content of particles sized from 0.1 to 0.002 mm increases with one relative unit, the K-factor increases with 0.0091 t ha h / ha MJ mm, while the same relative increase of the class of aggregation, results to an increase of the K-factor by 0.0034 t ha h / ha MJ mm. On the other side, the relationships between the K-factor values and the contents of clay and organic matter, and the class of profile water permeability, are linear, inversely proportional. When the clay content increases with one relative unit, the K-factor value decreases by 0.0099 t ha h / ha MJ mm. The same relative increases in the content of soil organic matter and the class of soil profile water permeability, result to a decrease of the values of K-factor respectively by 0.0042 and 0.0045 t ha h / ha MJ mm.

Considerations of erosion and storage of carbon, focusing on tropical landscapes in Puerto Rico and Panama (Invited)

NASA Astrophysics Data System (ADS)

Stallard, R. F.

2013-12-01

Humid tropical regions are particularly good settings to examine the terrestrial carbon and nutrient cycles because the high average temperatures combined with abundant water and frequent intense storms promote rapid biological activity, weathering, and physical erosion. In studying the human-modified carbon or nutrient cycles on particular landscapes, assessments of the impact of human activities must be compared to prior states of those landscapes with regard to (1) biogeochemical reservoir sizes on the landscape, (2) rates of transport through and out of the landscape, and (3) ultimate fate of the material exported. Ongoing studies in small catchments and larger adjacent watersheds in Puerto Rico (PR) and Panama (PTY) assess which biological, hydrologic, and geomorphic mechanisms have been affected by human activities. The catchments are on older volcanic rocks (6, 2 in PR), granitic rocks (3, all in PR), and one in PTY on limey sediments. Three of the volcanic catchments and one granitic catchment are agricultural. In all these landscapes, landslides, rather than surficial erosion, appear to be the largest regional sediment source, and the biggest landslide-producing storms occur once every few decades. Both landslide-related and surficial erosion are greater in agricultural catchments compared to forested catchments on the same lithology, and granitic landscapes are eroding far more rapidly than volcanic landscapes. Physical erosion on the granitic landscapes appears to be greatly in excess of reasonable equilibrium rates based on mass balances and estimates based on Be-10. The particulate-organic-carbon (POC) yields exceed combined dissolved organic (DOC) and inorganic (DIC) carbon yields in the granitic watersheds, but they are considerably less than the DOC+DIC yields in the volcanic watersheds. Annual yields of DIC and DOC relate linearly to annual runoff, whereas POC has a steep exponential-style increase with increasing runoff, indicating a strong sensitivity to climate change, compared to a linear response. POC yields are tied to sediment yields that are, in turn, far in excess of equilibrium yields. This excess implies that much of the present carbon transport in eastern PR is the result of erosion in excess of equilibrium. In essence, soils that have developed for thousands of years are eroding more rapidly than they are now forming. Carbon accumulation in soil is rapid, and in a landslide scar, which can endure thousands of years, half of the carbon is regenerated in 80 years and all of it in about 200 years. Thus, eroding carbon is being replaced with carbon from the atmosphere. In PR, sediments are delivered to reservoirs or the ocean; in PTY deposition is in reservoirs. These reservoirs are strongly coupled sinks for carbon and nutrients. After landslides, huge quantities of sediment are deposited along with considerable wood and other organic debris. Sediment that deposits in the crenulated arms of the reservoirs is quite rich in organic matter derived from lake productivity that has been greatly augmented by nutrients derived from agricultural lands and domestic wastes. Carbon storage in reservoirs exceeds forest storage, and unlike forests, increases with time.

Large-Scale Simulation of the Effects of Climate Change on Runoff Erosion Following Extreme Wildfire Events Authors: Gould, Adam, Warren, Barber, Wagenbrenner, Robichaud, Wang, Cherkauer

NASA Astrophysics Data System (ADS)

Gould, G.; Adam, J. C.; Barber, M. E.; Wagenbrenner, J. W.; Robichaud, P. R.; Wang, L.; Cherkauer, K. A.

2012-12-01

Across the western U.S., there is clear concern for increases in wildfire occurrence, severity, and post-fire runoff erosion due to projected climate changes. The aim of this study was to advance our capability to simulate post-fire runoff erosion at scales larger than a single hillslope to examine the relative contribution of sediment being released to larger streams and rivers in response to wildfire. We applied the Variable Capacity Infiltration-Water Erosion Prediction Project (VIC-WEPP), a newly-developed physically-based modeling framework that combines large-scale hydrology with hillslope-scale runoff erosion, over the Salmon River basin (SRB) in central Idaho. We selected the SRB for this study because of recent research that suggested that forest wildfires are likely contributing the majority of coarser sands that settle in downstream navigation channels and in reservoirs, causing adverse impacts to aquatic life, navigation, and flood storage. Using the Normalized Burn Ratio (NBR), burn intensity and severity maps show the regularity of wildfire occurrence in the SRB. These maps compare pre-fire images to next growing season images from the Landsat Thematic Mapper multispectral scanning sensor. Rather than implementing WEPP over all hillslopes within the SRB, we applied a representative hillslope approach. A monofractal scaling method downscales globally available 30 arc second digital elevation model (DEM) data to a 30 m resolution for simulations. This information determined the distribution of slope gradients within each VIC grid cell. This study applied VIC-WEPP over the 1979-2010 period and compared an ensemble of future climate simulations for the period of 2041-2070. For future scenarios, we only considered meteorological impacts on post-fire erosion and did not incorporate changes in future fire occurrence or severity. We ran scenarios for a variety of land cover and soil parameter sets, particularly those that relate to pre and post-fire characteristics, such as vegetative cover, interrill and rill erodibility factors, and saturated hydraulic conductivity. Evaluation of runoff erosion at experimental sites, observed by the U.S. Forest Service, involved using Disturbed WEPP which showed reasonable first post-fire year annual erosion predictions. We evaluated VIC-WEPP by comparing sediment observations downstream of the SRB with simulated yields for both pre and post-fire conditions. Generation of maps showing erosion over the SRB for each of the scenarios show specific areas within the SRB to be high, moderate, or low runoff-induced post-fire erosion regions. Our methodology will enable forest managers in the region to incorporate the impacts of changes in meteorological events on runoff erosion into their strategic management plans.

Non-uniform Erosion and Surface Evolution of Plasma-Facing Materials for Electric Propulsion

NASA Astrophysics Data System (ADS)

Matthes, Christopher Stanley Rutter

A study regarding the surface evolution of plasma-facing materials is presented. Experimental efforts were performed in the UCLA Pi Facility, designed to explore the physics of plasma-surface interactions. The influence of micro-architectured surfaces on the effects of plasma sputtering is compared with the response of planar samples. Ballistic deposition of sputtered atoms as a result of geometric re-trapping is observed. This provides a self-healing mechanism of micro-architectured surfaces during plasma exposure. This result is quantified using a QCM to demonstrate the evolution of surface features and the corresponding influence on the instantaneous sputtering yield. The sputtering yield of textured molybdenum samples exposed to 300 eV Ar plasma is found to be roughly 1 of the 2 corresponding value of flat samples, and increases with ion fluence. Mo samples exhibited a sputtering yield initially as low as 0.22+/-8%, converging to 0.4+/-8% at high fluence. Although the yield is dependent on the initial surface structure, it is shown to be transient, reaching a steady-state value that is independent of initial surface conditions. A continuum model of surface evolution resulting from sputtering, deposition and surface diffusion is also derived to resemble the damped Kuramoto-Sivashinsky (KS) equation of non-linear dynamics. Linear stability analysis of the evolution equation provides an estimate of the selected wavelength, and its dependence on the ion energy and angle of incidence. The analytical results are confirmed by numerical simulations of the equation with a Fast Fourier Transform method. It is shown that for an initially flat surface, small perturbations lead to the evolution of a selected surface pattern that has nano- scale wavelength. When the surface is initially patterned by other means, the final resulting pattern is a competition between the "templated" pattern and the "self-organized" structure. Potential future routes of research are also discussed, corresponding to a design analysis of the current experimental study.

Linear immunoglobulin A dermatosis mimicking toxic epidermal necrolysis: a case report of etanercept treatment.

PubMed

Prieto-Barrios, M; Velasco-Tamariz, V; Tous-Romero, F; Burillo-Martinez, S; Zarco-Olivo, C; Rodriguez-Peralto, J L; Ortiz-Romero, P L

2018-03-01

A 65-year-old pluripathological woman attended our hospital with a cutaneous eruption of sudden appearance after vancomycin treatment. She presented targetoid lesions affecting approximately 25-30% of her body surface, large erosions with mucosal lesions and positive Nikolsky sign. Under the initial clinical suspicion of toxic epidermal necrolysis (TEN), and considering the recent literature of successful use of etanercept in these cases, she was treated with a single dose of this antitumour necrosis factor (anti-TNF) agent. Subsequently, the exanthema progression stopped and resolution of the lesions happened in a few days. Later on, histopathology revealed a subepidermal blister with dense neutrophilic infiltrate and linear deposits of immunoglobulin A (IgA) on the dermoepidermal junction, allowing us to establish the diagnosis of drug-induced linear IgA dermatosis mimicking TEN. Linear IgA dermatosis can have severe clinical manifestations, even mimicking TEN, and can have high mortality, especially in drug-induced cases. We have not found any other report of linear IgA dermatosis treated with etanercept in the English literature. Anti-TNF medications could represent useful therapeutic alternatives in this dermatosis. © 2017 British Association of Dermatologists.

SELECTION OF RIPARIAN REACHES FOR RESTORATION AND PROTECTION WITHIN EROSION-PRONE LANDSCAPES. (R827149)

EPA Science Inventory

The perspectives, information and conclusions conveyed in research project abstracts, progress reports, final reports, journal abstracts and journal publications convey the viewpoints of the principal investigator and may not represent the views and policies of ORD and EPA. Concl...

Modelling soil erosion and associated sediment yield for small headwater catchments of the Daugava spillway valley, Latvia

NASA Astrophysics Data System (ADS)

Soms, Juris

2015-04-01

The accelerated soil erosion by water and associated fine sediment transfer in river catchments has various negative environmental as well as economic implications in many EU countries. Hence, the scientific community had recognized and ranked soil erosion among other environmental problems. Moreover, these matters might worsen in the near future in the countries of the Baltic Region, e.g. Latvia considering the predicted climate changes - more precisely, the increase in precipitation and shortening of return periods of extreme rainfall events, which in their turn will enable formation of surface runoff, erosion and increase of sediment delivery to receiving streams. Thereby it is essential to carry out studies focused on these issues in order to obtain reliable data in terms of both scientific and applied aims, e.g. environmental protection and sustainable management of soils as well as water resources. During the past decades, many of such studies of soil erosion had focused on the application of modelling techniques implemented in a GIS environment, allowing indirectly to estimate the potential soil losses and to quantify related sediment yield. According to research results published in the scientific literature, this approach currently is widely used all over the world, and most of these studies are based on the USLE model and its revised and modified versions. Considering that, the aim of this research was to estimate soil erosion rates and sediment transport under different hydro-climatic conditions in south-eastern Latvia by application of GIS-based modelling. For research purposes, empirical RUSLE model and ArcGIS software were applied, and five headwater catchments were chosen as model territories. The selected catchments with different land use are located in the Daugava spillway valley, which belongs to the upper Daugava River drainage basin. Considering lithological diversity of Quaternary deposits, a variety of soils can be identified, i.e., Stagnic Albeluvisols, Albic Rubic Arenosols and Albic Stagnic Podzols with stony loamy - clayey diamicton to coarse sand textures prevail in the selected catchments. The results of modelling were validated through obtaining data on suspended sediment load directly during episodic runoff events caused by different scenarios of runoff formation. In order to get comparable values of suspended sediment load from gully catchments that differ in size, an area-specific daily suspended sediment yield was derived. The obtained results indicate that modelled area-specific sediment yield from the catchments to river greatly varies from 0.001 to 97.2 t ha-1 yr-1; the average soil loss predicted by RUSLE for the each of five catchments calculated for a 1 × 1 m cell grid totals 0.81; 1.36; 0.96; 1.05 and 1.55 t ha-1 yr-1 respectively. Notably, despite the presence of forest vegetation that cover more than 40% of area of three of these catchments, sizable plots of soils are potentially prone to erosion rates above the tolerable threshold, i.e. 0.3 t ha-1 yr-1. Comparison of modelled vs. measured values indicates that the applied RUSLE model underestimates real sediment delivery, which shortly can reach values 213.75 kg ha-1 day-1 during intense snow melting in spring. Nevertheless, results of GIS modelling can be reasonably used to estimate the spatial distribution of soil erosion risk and to identify potential erosion hotspots.

[Underlying Mechanisms and Management of Refractory Gastroesophageal Reflux Disease].

PubMed

Lee, Kwang Jae

2015-08-01

The prevalence of gastroesophageal reflux disease (GERD) in South Korea has increased over the past 10 years. Patients with erosive reflux disease (ERD) shows better response to proton pump inhibitors (PPIs) than those with non-erosive reflux disease (NERD). NERD is a heterogeneous condition, showing pathological gastroesophageal reflux or esophageal hypersensitivity to reflux contents. NERD patients with pathological gastroesophageal reflux or hypersensitivity to acid may respond to PPIs. However, many patients with esophageal hypersensitivity to nonacid or functional heartburn do not respond to PPIs. Therefore, careful history and investigations are required when managing patients with refractory GERD who show poor response to conventional dose PPIs. Combined pH-impedance studies and a PPI diagnostic trial are recommended to reveal underlying mechanisms of refractory symptoms. For those with ongoing reflux-related symptoms, split dose administration, change to long-acting PPIs or PPIs less influenced by CYP2C19 genotypes, increasing dose of PPIs, and the addition of alginate preparations, prokinetics, selective serotonin reuptake inhibitors, or tricyclic antidepressants can be considered. Pain modulators, selective serotonin reuptake inhibitors, or tricyclic antidepressants are more likely to be effective for those with reflux-unrelated symptoms. Surgery or endoscopic per oral fundoplication may be effective in selected patients.

Mitigating Mitochondrial Genome Erosion Without Recombination.

PubMed

Radzvilavicius, Arunas L; Kokko, Hanna; Christie, Joshua R

2017-11-01

Mitochondria are ATP-producing organelles of bacterial ancestry that played a key role in the origin and early evolution of complex eukaryotic cells. Most modern eukaryotes transmit mitochondrial genes uniparentally, often without recombination among genetically divergent organelles. While this asymmetric inheritance maintains the efficacy of purifying selection at the level of the cell, the absence of recombination could also make the genome susceptible to Muller's ratchet. How mitochondria escape this irreversible defect accumulation is a fundamental unsolved question. Occasional paternal leakage could in principle promote recombination, but it would also compromise the purifying selection benefits of uniparental inheritance. We assess this tradeoff using a stochastic population-genetic model. In the absence of recombination, uniparental inheritance of freely-segregating genomes mitigates mutational erosion, while paternal leakage exacerbates the ratchet effect. Mitochondrial fusion-fission cycles ensure independent genome segregation, improving purifying selection. Paternal leakage provides opportunity for recombination to slow down the mutation accumulation, but always at a cost of increased steady-state mutation load. Our findings indicate that random segregation of mitochondrial genomes under uniparental inheritance can effectively combat the mutational meltdown, and that homologous recombination under paternal leakage might not be needed. Copyright © 2017 by the Genetics Society of America.

Detection of soil erosion with Thematic Mapper (TM) satellite data within Pinyon-Juniper woodlands

NASA Technical Reports Server (NTRS)

Price, Kevin Paul

1987-01-01

Pinyon-Juniper woodlands dominate approximately 24.3 million hectares (60 million acres) in the western United States. The overall objective was to test the sensitivity of the LANDSAT Thematic Mapper (TM) spectral data for detecting varying degrees of soil erosion within the Pinyon-Juniper woodlands. A second objective was to assess the potential of the spectral data for assigning the Universal Soil Loss Equation (USLE) crop management (C) factor values to varying cover types within the woodland. Thematic Mapper digital data for June 2, 1984 on channels 2, 3, 4, and 5 were used. Digital data analysis was performed using the ELAS software package. Best results were achieved using CLUS, an unsupervised clustering algorithm. Fifteen of the 40 Pinyon-Juniper signatures were identified as being relatively pure Pinyon-Juniper woodland. Final analysis resulted in the grouping of the 15 signatures into three major groups. Ten study sites were selected from each of the three groups and located on the ground. At each site the following field measurements were taken: percent tree canopy and percent understory cover, soil texture, total soil loss, and soil erosion rate estimates. A technique for measuring soil erosion within Pinyon-Juniper woodlands was developed. A theoretical model of site degradation after Pinyon-Juniper invasion is presented.

The importance of earthquake-induced landslides to long-term slope erosion and slope-failure hazards in seismically active regions

USGS Publications Warehouse

Keefer, D.K.

1994-01-01

This paper describes a general method for determining the amount of earthquake-induced landsliding that occurs in a seismically active region over time; this determination can be used as a quantitative measure of the long-term hazard from seismically triggered landslides as well as a measure of the importance of this process to regional slope-erosion rates and landscape evolution. The method uses data from historical earthquakes to relate total volume of landslide material dislodged by an earthquake to the magnitude, M, and seismic moment, M0, of the earthquake. From worldwide data, a linear-regression relation between landslide volume, V, and M0 is determined as: V = M0/1018.9(?? 0.13), where V is measured in m3 and M0 is in dyn-cm. To determine the amount of earthquake-generated landsliding over time, this relation is combined with data on seismic-moment release for a particular region, which may be derived from either earthquake-history or fault-slip data. The form of the M0-V relation allows the rate of production of earthquake-induced landslides over time to be determined from total rate of seismic-moment release without regard to the distribution of individual events, thus simplifying and generalizing the determination. Application of the method to twelve seismically active regions, with areas ranging from 13,275 to 2,308,000 km2, shows that erosion rates from earthquake-induced landslides vary significantly from region to region. Of the regions studied, the highest rates were determined for the island of Hawaii, New Zealand, western New Guinea, and the San Francisco Bay region of California. Significantly lower rates were determined for Iran, Tibet, the Sierra Nevada-Great Basin region of California, and central Japan (for the time period from 715 AD to the present). Intermediate rates were determined for Peru, southern California, onshore California, Turkey, and central Japan (for the time period from 1586 AD to the present). To determine the relative, long-term importance of seismically triggered landslides, these erosion rates are compared to erosion rates calculated for other slope processes and to rates calculated from fluvial sediment discharge. Comparisons with other slope processes indicate that earthquake-induced landslides are the predominant agents of slope erosion on the island of Hawaii, in the San Francisco Bay region, and in western New Guinea. For Hawaii, the San Francisco Bay region, and Sierra Nevada-Great Basin region of California, the erosion rates calculated for earthquake-induced landslides also exceed the regional erosion rates calculated from fluvial sediment discharge. ?? 1994.

A Spatially Distributed Conceptual Model for Estimating Suspended Sediment Yield in Alpine catchments

NASA Astrophysics Data System (ADS)

Costa, Anna; Molnar, Peter; Anghileri, Daniela

2017-04-01

Suspended sediment is associated with nutrient and contaminant transport in water courses. Estimating suspended sediment load is relevant for water-quality assessment, recreational activities, reservoir sedimentation issues, and ecological habitat assessment. Suspended sediment concentration (SSC) along channels is usually reproduced by suspended sediment rating curves, which relate SSC to discharge with a power law equation. Large uncertainty characterizes rating curves based only on discharge, because sediment supply is not explicitly accounted for. The aim of this work is to develop a source-oriented formulation of suspended sediment dynamics and to estimate suspended sediment yield at the outlet of a large Alpine catchment (upper Rhône basin, Switzerland). We propose a novel modelling approach for suspended sediment which accounts for sediment supply by taking into account the variety of sediment sources in an Alpine environment, i.e. the spatial location of sediment sources (e.g. distance from the outlet and lithology) and the different processes of sediment production and transport (e.g. by rainfall, overland flow, snowmelt). Four main sediment sources, typical of Alpine environments, are included in our model: glacial erosion, hillslope erosion, channel erosion and erosion by mass wasting processes. The predictive model is based on gridded datasets of precipitation and air temperature which drive spatially distributed degree-day models to simulate snowmelt and ice-melt, and determine erosive rainfall. A mass balance at the grid scale determines daily runoff. Each cell belongs to a different sediment source (e.g. hillslope, channel, glacier cell). The amount of sediment entrained and transported in suspension is simulated through non-linear functions of runoff, specific for sediment production and transport processes occurring at the grid scale (e.g. rainfall erosion, snowmelt-driven overland flow). Erodibility factors identify different lithological units, while the distance from the outlet is accounted for by including sediment wave velocities. The model is calibrated and validated on the basis of continuous turbidity data measured at the outlet of the basin. In addition, SSC data measured twice per week since 1964 are used to evaluate the performance of the model over longer time scales. Our predictive model is shown to reproduce SSC dynamics of the upper Rhône basin satisfactorily. The model accounts for the spatial distribution of sediment sources (location and processes of erosion and transport) and their activation/deactivation throughout the hydrological year. Therefore, it can reproduce the effects of changes in climate on sediment fluxes. In particular, we show that observed changes in SSC in the upper Rhône basin during the last 40 years are likely a consequence of increased air temperatures in this period and the consequent acceleration of glacial erosion.

Validating the Kinematic Wave Approach for Rapid Soil Erosion Assessment and Improved BMP Site Selection to Enhance Training Land Sustainability

DTIC Science & Technology

2014-02-01

installation based on a Euclidean distance allocation and assigned that installation’s threshold values. The second approach used a thin - plate spline ...installation critical nLS+ thresholds involved spatial interpolation. A thin - plate spline radial basis functions (RBF) was selected as the...the interpolation of installation results using a thin - plate spline radial basis function technique. 6.5 OBJECTIVE #5: DEVELOP AND

Influence of development stage and disturbance of physical and biological soil crusts on soil water erosion

NASA Astrophysics Data System (ADS)

Chamizo, S.; Cantón, Y.; Lázaro, R.; Solé-Benet, A.; Calvo-Cases, A.; Miralles, I.; Domingo, F.

2009-04-01

Most soils exposed to rainfall are prone to sealing and crusting processes causing physical soil crusts (PSCs). When climate and soil stability conditions are suitable, PSCs can be consolidated by a complex community consisting of cyanobacteria, bacteria, green algae, microfungi, lichens and bryophytes, which are collectively known as biological soil crust (BSC). The influence of soil crusts on erosion processes is complex: crusts may reduce detachment, increasing soil stability and protecting soil against raindrop impact, although that protection will depend on the type of soil crust and the stage of development; they can also build up runoff, suggesting that downstream erosion may actually be increased or favoured water harvesting to vegetated areas. On the other hand, BSCs have been demonstrated to be very vulnerable to disturbance which in turn can lead to accelerate soil erosion and other forms of land degradation. Incorporation of the response of different type of soil crusts and the effects of their disturbance is highly likely to improve the prediction of runoff and water erosion models in arid and semi-arid catchments. The objective of this work is to analyse the erosional response of PSCs and BSCs in different stages of their development and subject to distinct disturbances when extreme rainfalls intensities are applied at plot scale in semiarid environments. Small plots on the most representative crust types, corresponding to different stages of crust development, in two semiarid ecosystems in SE Spain, El Cautivo (in the Tabernas Desert) and Amoladeras (in the Natural Park Cabo de Gata-Níjar), were selected and three disturbance treatments were applied on each crust type: a) no disturbance (control), b) trampling, stepping 100 times over the crust and c) scraping. Two consecutive rainfall simulation experiments (50 mm/h rainfall intensity) were carried out on each plot: the first on dry soil and the second, 30 minutes later, on wet soil conditions. Samples of runoff were collected regularly during the rainfall simulation and sediments in runoff extracted later in laboratory. Erosion rates were significantly different at both sites, being lower in Amoladeras than in El Cautivo due to a flatter topography and a higher infiltration capacity of the sandy soils with higher organic matter content. There were not significant differences on total erosion rates between the first and the second rainfall event, as consequence of the increase of runoff under wet conditions. In El Cautivo, the erosion rates significantly decreased as crust development stage increased. However, in Amoladeras, the erosion was low in all crust types and there were not significant differences on erosion rates among the crust development stages. Among treatments, in El Cautivo, scraping and trampling promoted significant higher erosion rates than undisturbed crust, but no significant differences were found between both treatments, except for the lichen-dominated crust. In Amoladeras, no significant differences on erosion rates between the undisturbed and the trampled crust were found since in this area trampling did not have an important effect. Although the removal of the crust in semiarid environments, at local scale, always increased erosion, the effects of crust disturbance on erosion varied depending on the ecosystem, with stronger erosional effects in badland areas with a silty substrate and steep topography than in areas with a flat topography and a coarser soil texture.

Soil erosion in Iran: Issues and solutions

NASA Astrophysics Data System (ADS)

Hamidreza Sadeghi, Seyed; Cerdà, Artemi

2015-04-01

Iran currently faces many soil erosion-related problems (see citations below). These issues are resulted from some inherent characteristic and anthropogenic triggering forces. Nowadays, the latter plays more important rule to accelerate the erosion with further emphasis on soil erosion-prone arid and semi arid regions of the country. This contribution attempts to identify and describe the existing main reasons behind accelerated soil erosion in Iran. Appropriate solutions viz. structural and non-structural approaches will be then advised to combat or minimise the problems. Iran can be used as a pilot research site to understand the soil erosion processes in semiarid, arid and mountainous terrain and our research will review the scientific literature and will give an insight of the soil erosion rates in the main factors of the soil erosion in Iran. Key words: Anthropogenic Erosion, Land Degradation; Sediment Management; Sediment Problems Acknowledgements The research projects GL2008-02879/BTE, LEDDRA 243857 and PREVENTING AND REMEDIATING DEGRADATION OF SOILS IN EUROPE THROUGH LAND CARE (RECARE)FP7-ENV-2013- supported this research. References Aghili Nategh, N., Hemmat, A., & Sadeghi, M. (2014). Assessing confined and semi-confined compression curves of highly calcareous remolded soil amended with farmyard manure. Journal of Terramechanics, 53, 75-82. Arekhi, S., Bolourani, A. D., Shabani, A., Fathizad, H., Ahamdy-Asbchin, S. 2012. Mapping Soil Erosion and Sediment Yield Susceptibility using RUSLE, Remote Sensing and GIS (Case study: Cham Gardalan Watershed, Iran). Advances in Environmental Biology, 6(1), 109-124. Arekhi, S., Shabani, A., Rostamizad, G. 2012. Application of the modified universal soil loss equation (MUSLE) in prediction of sediment yield (Case study: Kengir Watershed, Iran). Arabian Journal of Geosciences, 5(6), 1259-1267.Sadeghi, S. H., Moosavi, V., Karami, A., Behnia, N. 2012. Soil erosion assessment and prioritization of affecting factors at plot scale using the Taguchi method. Journal of Hydrology, 448, 174-180. Asadi, H., Moussavi, A., Ghadiri, H., Rose, C. W. 2011. Flow-driven soil erosion processes and the size selectivity of sediment. Journal of Hydrology, 406(1), 73-81. Asadi, H., Raeisvandi, A., Rabiei, B., Ghadiri, H. 2012. Effect of land use and topography on soil properties and agronomic productivity on calcareous soils of a semiarid region, Iran. Land Degradation & Development, 23(5), 496-504. Ayoubi, S., Ahmadi, M., Abdi, M. R., Abbaszadeh Afshar, F. 2012. Relationships of< sup> 137 Cs inventory with magnetic measures of calcareous soils of hilly region in Iran. Journal of environmental radioactivity, 112, 45-51. Ayoubi, S., Mokhtari Karchegani, P., Mosaddeghi, M. R., Honarjoo, N. 2012. Soil aggregation and organic carbon as affected by topography and land use change in western Iran. Soil and Tillage Research, 121, 18-26. Emadodin, I., Bork, H. R. 2012. Degradation of soils as a result of long-term human-induced transformation of the environment in Iran: an overview. Journal of Land Use Science, 7(2), 203-219. Emadodin, I., Narita, D., Bork, H. R. 2012. Soil degradation and agricultural sustainability: an overview from Iran. Environment, Development and Sustainability, 14(5), 611-625. Haddadchi, A., Nosrati, K., Ahmadi, F. 2014. Differences between the source contribution of bed material and suspended sediments in a mountainous agricultural catchment of western Iran. CATENA, 116, 105-113. Heshmati, M., Arifin, A., Shamshuddin, J., Majid, N. M. 2012. Predicting N, P, K and organic carbon depletion in soils using MPSIAC model at the Merek catchment, Iran. Geoderma, 175, 64-77. Jafari, R., Bakhshandehmehr, L. 2013. Quantitative mapping and assessment of environmentally sensitive areas to desertification in central Iran. Land Degradation & Development.DOI: 10.1002/ldr.2227 Kavian, A., Azmoodeh, A., Solaimani, K. 2014. Deforestation effects on soil properties, runoff and erosion in northern Iran. Arabian Journal of Geosciences, 7(5), 1941-1950. Khaledi Darvishan, A., Sadeghi, S. H., Homaee, M., Arabkhedri, M. 2013. Measuring sheet erosion using synthetic color-contrast aggregates. Hydrological Processes. Mahmoodabadi, M. Cerdà, A. 2013. WEPP calibration for improved predictions on interril erosion in semi-arid to arid enviorments. Geoderma, 204-205,75-83. http://dx.doi.org/10.1016/j.geoderma.2013.04.013, Mehdizade, B., Asadi, H., Shabanpour, M., Ghadiri, H. 2013. Impact of erosion and tillage on the productivity and quality of selected semiarid soils of Iran. International Agrophysics, 27(3), 291-297. Moghadam, B. K., Jabarifar, M., Bagheri, M., Shahbazi, E. 2015. Effects of land use change on soil splash erosion in the semi-arid region of Iran. Geoderma, 241, 210-220. Nosrati, K., Ahmadi, F. 2013. Monitoring of soil organic carbon and nitrogen stocks in different land use under surface water erosion in a semi-arid drainage basin of Iran. Journal of Applied Sciences and Environmental Management, 17(2), 225-230. Nourzadeh, M., Bahrami, H. A., Goossens, D., Fryrear, D. W. 2013. Determining soil erosion and threshold friction velocity at different soil moisture conditions using a portable wind tunnel. Zeitschrift für Geomorphologie, 57(1), 97-109. Sadeghi, S. H. R., Seghaleh, M. B., Rangavar, A. S. 2013. Plot sizes dependency of runoff and sediment yield estimates from a small watershed. Catena, 102, 55-61. Sadeghi, S. H. R., Seghaleh, M. B., Rangavar, A. S. 2013. Plot sizes dependency of runoff and sediment yield estimates from a small watershed. Catena, 102, 55-61. Sadeghi, S. H., Najafi, S., Riyahi Bakhtiari, A., Abdi, P. 2014. Ascribing soil erosion types for sediment yield using composite fingerprinting technique. Hydrological Sciences Journal, 59(9), 1753-1762. Taghizadeh-Mehrjardi, R., Minasny, B., Sarmadian, F., Malone, B. P. 2014. Digital mapping of soil salinity in Ardakan region, central Iran. Geoderma, 213, 15-28.

Measurement uncertainty associated with chromatic confocal profilometry for 3D surface texture characterization of natural human enamel.

PubMed

Mullan, F; Bartlett, D; Austin, R S

2017-06-01

To investigate the measurement performance of a chromatic confocal profilometer for quantification of surface texture of natural human enamel in vitro. Contributions to the measurement uncertainty from all potential sources of measurement error using a chromatic confocal profilometer and surface metrology software were quantified using a series of surface metrology calibration artifacts and pre-worn enamel samples. The 3D surface texture analysis protocol was optimized across 0.04mm 2 of natural and unpolished enamel undergoing dietary acid erosion (pH 3.2, titratable acidity 41.3mmolOH/L). Flatness deviations due to the x, y stage mechanical movement were the major contribution to the measurement uncertainty; with maximum Sz flatness errors of 0.49μm. Whereas measurement noise; non-linearity's in x, y, z and enamel sample dimensional instability contributed minimal errors. The measurement errors were propagated into an uncertainty budget following a Type B uncertainty evaluation in order to calculate the Standard Combined Uncertainty (u c ), which was ±0.28μm. Statistically significant increases in the median (IQR) roughness (Sa) of the polished samples occurred after 15 (+0.17 (0.13)μm), 30 (+0.12 (0.09)μm) and 45 (+0.18 (0.15)μm) min of erosion (P<0.001 vs. baseline). In contrast, natural unpolished enamel samples revealed a statistically significant decrease in Sa roughness of -0.14 (0.34) μm only after 45min erosion (P<0.05s vs. baseline). The main contribution to measurement uncertainty using chromatic confocal profilometry was from flatness deviations however by optimizing measurement protocols the profilometer successfully characterized surface texture changes in enamel from erosive wear in vitro. Copyright © 2017 The Academy of Dental Materials. All rights reserved.

Effect of rainfall intensity and slope steepness on the development of soil erosion in the Southern Cis-Ural region (A model experiment)

NASA Astrophysics Data System (ADS)

Sobol, N. V.; Gabbasova, I. M.; Komissarov, M. A.

2017-09-01

The effect of rainfall intensity on the erosion of residual calcareous agrogray soils and clay-illuvial agrochernozems in the Southern Cis-Ural region on slopes of different inclination and vegetation type has been studied by simulating with a small-size sprinkler. It has been shown that soil loss linearly depends on rainfall intensity (2, 4, and 6 mm/min) and slope inclination (3° and 7°). When the rainfall intensity and duration, and the slope inclination increase, soil loss by erosion from agrogray soils increases higher than from agrochernozems. On the plowland with a slope of 3°, runoff begins 12, 10, and 5 min, on the average, after the beginning of rains at these intensities. When the slope increases to 7°, runoff begins earlier by 7, 6, and 4 min, respectively. After the beginning of runoff and with its increase by 1 mm, the soil loss from slopes of 3° and 7° reaches 4.2 and 25.7 t/ha on agrogray soils and 1.4 and 4.7 t/ha on agrochernozems, respectively. Fallow soils have higher erosion resistance, and the soil loss little depends on the slope gradient: it gradually increases to 0.3-1.0 t/ha per 1 mm of runoff with increasing rainfall intensity and duration. The content of physical clay in eroded material is higher than in the original soils. Fine fractions prevail in this material, which increases their humus content. The increase in rainfall intensity and duration to 4 and 6 mm/min results in the entrapment of coarse silt and sand by runoff.

Steady evolution of hillslopes in layered landscapes: self-organization of a numerical hogback

NASA Astrophysics Data System (ADS)

Glade, R.; Anderson, R. S.

2017-12-01

Landscapes developed in layered sedimentary or igneous rocks are common across Earth, as well as on other planets. Features such as hogbacks, exposed dikes, escarpments and mesas exhibit resistant rock layers in tilted, vertical, or horizontal orientation­s adjoining more erodible rock. Hillslopes developed in the erodible rock are typically characterized by steep, linear-to-concave slopes or "ramps" mantled with material derived from the resistant layers, often in the form of large blocks. Our previous work on hogbacks has shown that feedbacks between weathering and transport of the blocks and underlying soft rock are fundamental to their formation; our numerical model incorporating these feedbacks explain the development of commonly observed concave-up slope profiles in the absence of rilling processes. Here we employ an analytic approach to describe the steady behavior of our model, in which hillslope form and erosion rates remain constant in the reference frame of the retreating feature. We first revisit a simple geometric analysis that relates structural dip to erosion rates. We then explore the mechanisms by which our numerical model of hogback evolution self-organizes to meet these geometric expectations. Autogenic adjustment of soil depth, slope and erosion rates enables efficient transport of resistant blocks; this allows erosion of the resistant layer to keep up with base level fall rate, leading to steady evolution of the feature. Analytic solutions relate easily measurable field quantities such as ramp length, slope, block size and resistant layer dip angle to local incision rate, block velocity, and block weathering rate. These equations provide a framework for exploring the evolution of layered landscapes, and pinpoint the processes for which we require a more thorough understanding to predict the evolution of such signature landscapes over time.

Longitudinal Assessment of Synovial, Lymph Node, and Bone Volumes in Inflammatory Arthritis in Mice using in vivo MRI and micro-CT

PubMed Central

Proulx, Steven T.; Kwok, Edmund; You, Zhigang; Papuga, M. Owen; Beck, Christopher A.; Shealy, David J.; Ritchlin, Christopher T.; Awad, Hani A.; Boyce, Brendan F.; Xing, Lianping; Schwarz, Edward M.

2009-01-01

Objective Development of longitudinal 3D outcomes of inflammation and bone erosion in murine arthritis using contrast enhanced (CE) MRI and in vivo micro-CT; and in a pilot study, to determine the value of entrance criteria by age versus synovial volume in therapeutic intervention studies. Methods CE-MRI and in vivo micro-CT was performed on TNF-Tg and WT littermates to quantify the synovial and popliteal lymph node (LN) volumes and patella and talus bone volumes, respectively, which were validated with histology. These longitudinal outcome measures were used to assess the natural history of inflammatory-erosive arthritis. We also performed anti-TNF versus placebo efficacy studies in TNF-Tg mice in which treatment was initiated either by age (4–5 months) or synovial volume (3mm3 as detected by CE-MRI). Linear regression was performed to analyze the correlation between synovitis and focal erosion. Results CE-MRI demonstrated the highly variable nature of TNF-induced joint inflammation. Initiation of treatment by synovial volume produced significantly larger treatment effects on synovial volume (p=0.04) and lymph node volume (p<0.01) than initiation by age. By correlating the MRI and microCT data we were able to demonstrate a significant relationship between changes in synovial and patellar volumes (R2 =0.75; p<0.01). Conclusion In vivo CE-MRI and micro-CT 3D outcome measures are powerful tools that accurately demonstrate the progression of inflammatory-erosive arthritis in mice. These methods can be used to identify mice with arthritis of similar severity before intervention studies are initiated and thus minimize heterogeneity in outcome studies of chronic arthritis seen between genetically identical littermates. PMID:18050199

Ultimate pier and contraction scour prediction in cohesive soils at selected bridges in Illinois.

DOT National Transportation Integrated Search

2013-09-01

The Scour Rate In COhesive Soils-Erosion Function Apparatus (SRICOS-EFA) method includes an ultimate scour prediction that is : the equilibrium maximum pier and contraction scour of cohesive soils over time. The purpose of this report is to present t...

Western Juniper Field Guide: Asking the Right Questions to Select Appropriate Management Actions

USDA-ARS?s Scientific Manuscript database

The rapid expansion of western juniper into neighboring plant communities during the past 130 years has been linked to increased soil erosion; reduced forage production; altered wildlife habitat; changes in plant community composition, structure, and biodiversity. Impacts of post-settlement woodland...

Impact of Land Use Change to the Soil Erosion Estimation for Cultural Landscapes: Case Study of Paphos Disrict in Cyprus

NASA Astrophysics Data System (ADS)

Cuca, B.; Agapiou, A.

2017-05-01

In 2006 UNESCO report has identified soil loss as one of the main threats of climate change with possible impact to natural and cultural heritage. The study illustrated in this paper shows the results from geomatic perspective, applying an interdisciplinary approach undertaken in order to identify major natural hazards affecting cultural landscapes and archaeological heritage in rural areas in Cyprus. In particular, Earth Observation (EO) and ground-based methods were identified and applied for mapping, monitoring and estimation of the possible soil loss caused by soil erosion. Special attention was given to the land use/land cover factor (C) and its impact on the overall estimation of the soil-loss. Cover factor represents the effect of soil-disturbing activities, plants, crop sequence and productivity level, soil cover and subsurface bio-mass on soil erosion. Urban areas have a definite role in retarding the recharge process, leading to increased runoff and soil loss in the broader area. On the other hand, natural vegetation plays a predominant role in reducing water erosion. The land use change was estimated based on the difference of the NDVI value between Landsat 5 TM and Sentinel-2 data for the period between 1980s' until today. Cover factor was then estimated for both periods and significant land use changes were further examined in areas of significant cultural and natural landscape value. The results were then compared in order to study the impact of land use change on the soil erosion and hence on the soil loss rate in the selected areas.

Saliva composition in three selected groups with normal stimulated salivary flow rates, but yet major differences in caries experience and dental erosion.

PubMed

Bardow, Allan; Lykkeaa, Joan; Qvist, Vibeke; Ekstrand, Kim; Twetman, Svante; Fiehn, Niels-Erik

2014-08-01

It was hypothesized that, by comparing matched subjects with major differences in these dental diseases, but yet normal saliva flow rates, it would be possible to obtain data on the effect of saliva composition on dental disease isolated from the effect of the flow rate. Thus, the aim of the study was to compare the major physicochemical characteristics of stimulated whole saliva in three groups of 85 subjects, each with normal saliva flow rates and at least 24 remaining teeth. A group with very little dental disease (healthy), a group with dental erosion (erosion) and a group with very high caries experience (caries) were chosen. Furthermore, the aim was to determine whether differences among groups could also be found on an individual level. Although it was not possible to retrieve three groups whose members were completely identical, the present study points in the direction that, on a group level, subjects with very little dental disease seemed to have a more favorable physicochemical saliva composition with respect to higher calcium, phosphate, bicarbonate, pH, degree of saturation with respect to hydroxyapatite and a lower critical pH (p < 0.05 or less). However, on an individual level the explanatory power for the saliva composition was only 10% for caries experience and only 11% for dental erosion (p < 0.001). The compositional analyses performed in this study on stimulated whole saliva, including major physicochemical characteristics of saliva, will most likely have little predictive value for future dental caries and erosion in single individuals.

Assessing shoreline exposure and oyster habitat suitability maximizes potential success for sustainable shoreline protection using restored oyster reefs

USGS Publications Warehouse

LaPeyre, Megan K.; Serra, Kayla; Joyner, T. Andrew; Humphries, Austin T.

2015-01-01

Oyster reefs provide valuable ecosystem services that contribute to coastal resilience. Unfortunately, many reefs have been degraded or removed completely, and there are increased efforts to restore oysters in many coastal areas. In particular, much attention has recently been given to the restoration of shellfish reefs along eroding shorelines to reduce erosion. Such fringing reef approaches, however, often lack empirical data to identify locations where reefs are most effective in reducing marsh erosion, or fully take into account habitat suitability. Using monitoring data from 5 separate fringing reef projects across coastal Louisiana, we quantify shoreline exposure (fetch + wind direction + wind speed) and reef impacts on shoreline retreat. Our results indicate that fringing oyster reefs have a higher impact on shoreline retreat at higher exposure shorelines. At higher exposures, fringing reefs reduced marsh edge erosion an average of 1.0 m y−1. Using these data, we identify ranges of shoreline exposure values where oyster reefs are most effective at reducing marsh edge erosion and apply this knowledge to a case study within one Louisiana estuary. In Breton Sound estuary, we calculate shoreline exposure at 500 random points and then overlay a habitat suitability index for oysters. This method and the resulting visualization show areas most likely to support sustainable oyster populations as well as significantly reduce shoreline erosion. Our results demonstrate how site selection criteria, which include shoreline exposure and habitat suitability, are critical to ensuring greater positive impacts and longevity of oyster reef restoration projects.

Late Complication of Surgically Treated Atlantoaxial Instability: Occipital Bone Erosion Induced by Protruded Fixed Titanium Rod: A Case Report

PubMed Central

Nakao, Yaoki; Shimokawa, Nobuyuki; Morisako, Hiroki; Tsukazaki, Yuji; Terada, Aiko; Nakajo, Kosuke; Fu, Yoshihiko

2014-01-01

Objective Polyaxial screw-rod fixation of C1-C2 is a relatively new technique to treat atlantoaxial instability, and there have been few reports in the literature outlining all possible complications. The purpose of this case report is to present the occurrence and management of occipital bone erosion induced by the protruded rostral part of a posterior atlantoaxial screw-rod construct causing headache. Clinical Features A 70-year-old Asian man with rheumatoid arthritis initially presented to our institution with atlantoaxial instability causing progressive quadraparesis and neck pain. Intervention and Outcome Posterior atlantoaxial instrumented fixation using C1 lateral mass screws in conjunction with C2 pedicle screws was performed to stabilize these segments. Postoperatively, the patient regained the ability to independently walk and had no radiographic evidence of instrumentation hardware failure and excellent sagittal alignment. However, despite a well-stabilized fusion, the patient began to complain of headache during neck extension. Follow-up imaging studies revealed left occipital bone erosion induced by a protruded titanium rod fixed with setscrews. During revision surgery, the rod protrusion was modified and the headaches diminished. Conclusion This case demonstrates that occipital bone erosion after posterior atlantoaxial fixation causing headache may occur. The principal cause of bone erosion in this case was rod protrusion. Although posterior atlantoaxial fixation using the screw-rod system was selected to manage atlantoaxial instability because it has less complications than other procedures, surgeons should pay attention that the length of the rod protrusion should not exceed 2 mm. PMID:25435842

Effectiveness of streambank-stabilization techniques along the Kenai River, Alaska

USGS Publications Warehouse

Dorava, Joseph M.

1999-01-01

The Kenai River in southcentral Alaska is the State's most popular sport fishery and an economically important salmon river that generates as much as $70 million annually. Boatwake-induced streambank erosion and the associated damage to riparian and riverine habitat present a potential threat to this fishery. Bank-stabilization techniques commonly in use along the Kenai River were selected for evaluation of their effectiveness at attenuating boatwakes and retarding streambank erosion. Spruce trees cabled to the bank and biodegradable man-made logs (called 'bio-logs') pinned to the bank were tested because they are commonly used techniques along the river. These two techniques were compared for their ability to reduce wake heights that strike the bank and to reduce erosion of bank material, as well as for the amount and quality of habitat they provide for juvenile chinook salmon. Additionally, an engineered bank-stabilization project was evaluated because this method of bank protection is being encouraged by managers of the river. During a test that included 20 controlled boat passes, the spruce trees and the bio-log provided a similar reduction in boatwake height and bank erosion; however, the spruce trees provided a greater amount of protective habitat than the bio-log. The engineered bank-stabilization project eroded less during nine boat passes and provided more protective cover than the adjacent unprotected natural bank. Features of the bank-stabilization techniques, such as tree limbs and willow plantings that extended into the water from the bank, attenuated the boatwakes, which helped reduce erosion. These features also provided protective cover to juvenile salmon.

Preliminary Evaluation of Cavitation-Erosion Resistance of Ti-Alloys in Mercury for the Spallation Neutron Source

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pawel, Steven J; Mansur, Louis K

2010-01-01

A number of Ti-based alloys in both the mill-annealed and 20% cold-worked conditions were subjected to sonication conditions in Hg using a vibratory horn to assess relative cavitation-erosion resistance. Weight loss as a function of exposure time was roughly proportional to hardness for all alloys/conditions examined, with Ti-6Al-4V (Ti-Grade 5) and Ti-6Al-2Sn-4Zr-2Mo yielding the best resistance to cavitation-erosion as evidenced by low weight losses and little or no tendency to form pits on the exposed surface. Unalloyed Ti (Ti-Grade 4) and Ti-0.12Pd (Ti-Grade 7) exhibited greater weight losses by a factor or about two and about five, respectively, with Ti-0.12Pdmore » particularly prone to pitting development. The mean erosion rates of the best two Ti-alloys examined here were about a factor of three higher than identically tested 316LN stainless steel following a low temperature carburizing treatment, but this difference is considered minor given that the rate for both materials is very low/manageable and represents a through-thickness property for the Ti-alloys. A nitriding surface treatment was also evaluated as a potential method to further increase the cavitation-erosion resistance of these alloys in Hg, but the selected treatment proved largely ineffective. Recommendations for further work to evaluate the efficacy of Ti-based alloys for use in high-powered targets for the Spallation Neutron Source are given.« less

Laboratory Observations of Dune Erosion

NASA Astrophysics Data System (ADS)

Maddux, T. B.; Ruggiero, P.; Palmsten, M.; Holman, R.; Cox, D. T.

2006-12-01

Coastal dunes are an important feature along many coastlines, owing to their input to the sediment supply, use as habitat, and ability to protect onshore resources from wave attack. Correct predictions of the erosion and overtopping rates of these features are needed to develop improved responses to coastal dune damage events, and to determining the likelihood and magnitude of future erosion and overtopping on different beaches. We have conducted a large-scale laboratory study at Oregon State University's O.H. Hinsdale Wave Research Laboratory (HWRL) with the goal of producing a comprehensive, near prototype-scale, physical model data set of hydrodynamics, sediment transport, and morphological evolution during extreme dune erosion events. The two goals of this work are (1) to develop a better understanding of swash/dune dynamics and (2) to evaluate and guide further development of dune erosion models. We present initial results from the first phase of the experimental program. An initial beach and dune profile was selected based on field LIDAR-based observations of various U.S. east coast and Gulf coast dune systems. The laboratory beach was brought to equilibrium with pre-storm random wave conditions. It was subsequently subjected to attack from steadily increasing water level and offshore wave heights. Observations made include inner surf zone and swash free surface and velocities as well as wave-by-wave estimates of topographical change at high spatial resolution through the use of stereo video imagery. Future work will include studies of fluid overtopping of the dune and sediment overwash and assessment of the resilience of man-made "push-up" dunes to wave attack in comparison with their more-compacted "natural" cousins.

Thermal Shock and Ablation Behavior of Tungsten Nozzle Produced by Plasma Spray Forming and Hot Isostatic Pressing

NASA Astrophysics Data System (ADS)

Wang, Y. M.; Xiong, X.; Zhao, Z. W.; Xie, L.; Min, X. B.; Yan, J. H.; Xia, G. M.; Zheng, F.

2015-08-01

Tungsten nozzle was produced by plasma spray forming (PSF, relative density of 86 ± 2%) followed by hot isostatic pressing (HIPing, 97 ± 2%) at 2000 °C and 180 MPa for 180 min. Scanning electron microscope, x-ray diffractometer, Archimedes method, Vickers hardness, and tensile tests have been employed to study microstructure, phase composition, density, micro-hardness, and mechanical properties of the parts. Resistance of thermal shock and ablation behavior of W nozzle were investigated by hot-firing test on solid rocket motor (SRM). Comparing with PSF nozzle, less damage was observed for HIPed sample after SRM test. Linear ablation rate of nozzle made by PSF was (0.120 ± 0.048) mm/s, while that after HIPing reduced to (0.0075 ± 0.0025) mm/s. Three types of ablation mechanisms including mechanical erosion, thermophysical erosion, and thermochemical ablation took place during hot-firing test. The order of degree of ablation was nozzle throat > convergence > dilation inside W nozzle.

Modeling Bottom Sediment Erosion Process by Swirling the Flow by Tangential Supply of Oil in the Tank

NASA Astrophysics Data System (ADS)

Nekrasov, V. O.

2016-10-01

The article carries out a statistical data processing of quantitative and territorial division of oil tanks operating in Tyumen region, intended for reception, storage and distribution of commercial oil through trunk pipelines. It describes the working principle of the new device of erosion and prevention of oil bottom sediment formation with tangential supply of oil pumped into reservoir. The most significant similarity criteria can be emphasized in modeling rotational flows exerting significant influence on the structure of the circulating flow of oil in tank when operation of the device described. The dependence of the distribution of the linear velocity of a point on the surface along the radius at the circular motion of the oil in the tank is characterized, and on the basis of this dependence, a formula of general kinetic energy of rotational motion of oil and asphalt-resin-paraffin deposits total volume in the oil reservoir is given.

Environmental processes and spectral reflectance characteristics associated with soil erosion in desert fringe regions

NASA Technical Reports Server (NTRS)

Jacobberger, P. A.

1986-01-01

Two Thematic Mapper (TM) scenes were acquired. A scene was acquired for the Bahariya, Egypt field area, and one was acquired covering the Okavango Delta site. Investigations at the northwest Botswana study sites have concentrated upon a system of large linear (alab) dunes possessing an average wavelength of 2 kilometers and an east-west orientation. These dunes exist to the north and west of the Okavango Swamp, the pseudodeltaic end-sink of the internal Okavango-Cubango-Cuito drainage network. One archival scene and two TM acquisitions are on order, but at present no TM data were acquired for the Tombouctou/Azaouad Dunes, Mali. The three areas taken together comprise an environmental series ranging from hyperarid to semi-arid, with desertization processes operational or incipient in each. The long range goal is to predict normal seasonal variations, so that aperiodic spectral changes resulting from soil erosion, vegetation damage, and associated surface processes would be distinguishable as departures from the norm.

On the Lateral Retreat of Salt Marshes: Field Monitoring in the Venice Lagoon (Italy)

NASA Astrophysics Data System (ADS)

Solari, L.; Bendoni, M.; Mel, R.; Oumeraci, H.; Francalanci, S.; Lanzoni, S.

2014-12-01

Salt marshes are geomorphic structures located in ecotone environments such as lagoon and estuaries, providing lot of ecosystem services to local population. In the last decades they are disappearing due to several factors such as sea level rise, subsidence and edge erosion due to surface waves. The latter is likely the chief mechanism modeling marsh boundaries and leading to the loss of wide marsh areas. In the case of the Venice Lagoon, from the beginning of the last century, the whole salt marsh surface has more than halved and trends indicate that the salt marshes might completely disappear over the next 50 years. Here, we present a field monitoring activity that we are currently carrying out on a retreating salt marsh located in the north part of the Lagoon of Venice (Italy). The marsh is subject to North-East (Bora) wind. Marsh area loss during the last decades has been documented through the comparison of georeferenced aerial photographs showing a retreat rate of the order of 1 m/year. Field measurements started by the end of November 2013 and consist of: salt marsh bank geometry at different cross-sections and wave climate in the lagoon about 30 m in front of the salt marsh. Erosion data are obtained by means of erosion pins located horizontally on the marsh scarp; at higher banks (about 0.9 m), two pins are located along the same vertical direction, for lower banks (about 0.4m), only one pin is employed. Significant wave height has been measured during three storm surges by means of pressure transducers (Pts). The measured wave climate in front of the bank was then put into relationship with the offshore wave climate estimated using wind data (intensity and direction) and bathymetric data. Wind intensity and direction is measured hourly by several measurement stations located in the Lagoon of Venice. In this way, it is possible to extrapolate wave climate hourly at the monitored marsh and calculate the wave power that acted on the bank in a given time interval. Field survey revealed that the main retreating mechanisms are particle by particle erosion alternated to cantilever failures. Preliminary results show a linear relationship between erosion rate and wave energy flux and the existence of a critical threshold for the onset of erosion.

Gully erosion in the Caatinga biome, Brazil: measurement and stochastic modelling

NASA Astrophysics Data System (ADS)

Lima Alencar, Pedro Henrique; de Araújo, José Carlos; Nonato Távora Costa, Raimundo

2017-04-01

In contrast with inter-rill erosion, which takes a long time to modify the terrain form, gully erosion can fast and severely change the landscape. In the Brazilian semiarid region, a one-million km2 area that coincides with the Caatinga biome, inter-rill erosion prevails due to the silty shallow soils. However, gully erosion does occur in the Caatinga, with temporal increasing severity. This source of sediment impacts the existing dense network of small dams, generating significant deleterious effects, such as water availability reduction in a drought-prone region. This study focuses on the Madalena basin (124 km2, state of Ceará, Brazil), a land-reform settlement with 20 inhabitants per km2, whose main economic activities are agriculture (especially Zea mays), livestock and fishing. In the catchment area, where there are 12 dams (with storage capacity ranging from 6.104 to 2.107 m3), gully erosion has become an issue due to its increasing occurrence. Eight gully-erosion sites have been identified in the basin, but most of them have not yet reached great dimensions (depth and/or width), nor interacted with groundwater, being therefore classified as ephemeral gullies. We selected the three most relevant sites and measured the topography of the eroded channels, as well as the neighboring terrain relief, using accurate total stations and unmanned aerial vehicle. The data was processed with the help of software, such as DataGeosis (Office 7.5) and Surfer (11.0), providing information on gully erosion in terms of (μ ± σ): projection area (317±165 m2), eroded mass (61±36 Mg) and volume (42±25 m3), length (38±6 m), maximum depth (0.58±0.13 m) and maximum width (6.00±2.35 m). The measured data are then compared with those provided by the Foster and Lane model (1986). The model generated results with considerable scatter. This is possibly due to uncertainties in the field parameters, which are neglected in the deterministic approach of most physically-based models. We propose that the gully-erosion model approach consider the uncertainties of its main parameters/variables (e.g., soil density, soil grain-size distribution and peak discharge); and generate a histogram of responses, rather than a single deterministic value. The principle of maximum entropy should be used to derive the probability density functions of the uncertainty content of parameters and variables.

The history of human-induced soil erosion: Geomorphic legacies, early descriptions and research, and the development of soil conservation—A global synopsis

NASA Astrophysics Data System (ADS)

Dotterweich, Markus

2013-11-01

This paper presents a global synopsis about the geomorphic evidence of soil erosion in humid and semihumid areas since the beginning of agriculture. Historical documents, starting from ancient records to data from the mid-twentieth century and numerous literature reviews form an extensive assortment of examples that show how soil erosion has been perceived previously by scholars, land surveyors, farmers, land owners, researchers, and policy makers. Examples have been selected from ancient Greek and Roman Times and from central Europe, southern Africa, North America, the Chinese Loess Plateau, Australia, New Zealand, and Easter Island. Furthermore, a comprehensive collection on the development of soil erosion research and soil conservation has been provided, with a particular focus on Germany and the USA. Geomorphic evidence shows that most of the agriculturally used slopes in the Old and New Worlds had already been affected by soil erosion in earlier, prehistoric times. Early descriptions of soil erosion are often very vague. With regard to the Roman Times, geomorphic evidence shows seemingly opposing results, ranging from massive devastation to landscapes remaining stable for centuries. Unfortunately, historical documentation is lacking. In the following centuries, historical records become more frequent and more precise and observations on extreme soil erosion events are prominent. Sometimes they can be clearly linked to geomorphic evidence in the field. The advent of professional soil conservation took place in the late eighteenth century. The first extensive essay on soil conservation known to the Western world was published in Germany in 1815. The rise of professional soil conservation occurred in the late nineteenth and early twentieth centuries. Soil remediation and flood prevention programs were initiated, but the long-term success of these actions remains controversial. In recent years, increasing interest is to recover any traditional knowledge of soil management in order to incorporate it into modern soil conservation strategies. The study shows that local and regional variations in natural settings, cultural traditions, and socioeconomic conditions played a major role for the dynamics and the rates of soil erosion on a long-term perspective. Geomorphic evidence and historical sources can often complement each other, but there should be also an awareness of new pitfalls when using them together.

Electrochemical and Dry Sand Impact Erosion Studies on Carbon Steel

PubMed Central

Naz, M. Y.; Ismail, N. I.; Sulaiman, S. A.; Shukrullah, S.

2015-01-01

This study investigated the dry and aqueous erosion of mild steel using electrochemical and dry sand impact techniques. In dry sand impact experiments, mild steel was eroded with 45 μm and 150 μm sand particles. Scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX) and micro-hardness techniques were used to elaborate the surface morphology of the eroded samples. The results revealed significant change in morphology of the eroded samples. In-depth analysis showed that although the metal erosion due to larger particles was significantly higher, the fines also notably damaged the metal surface. The surface damages were appreciably reduced with decrease in impact angle of the accelerated particles. The maximum damages were observed at an impact angle of 90°. The hardness of the samples treated with 45 μm and 150 μm sand remained in the range of 88.34 to 102.31 VHN and 87.7 to 97.55 VHN, respectively. In electrochemical experiments, a triple electrode probe was added into the metal treatment process. The linear polarization resistance (LPR) measurements were performed in slurries having 5% (by weight) of sand particles. LPR of the samples treated with 45 μm and 150 μm sand slurries was calculated about 949 Ω.cm2 and 809 Ω.cm2, respectively. PMID:26561231

Electrochemical and Dry Sand Impact Erosion Studies on Carbon Steel.

PubMed

Naz, M Y; Ismail, N I; Sulaiman, S A; Shukrullah, S

2015-11-12

This study investigated the dry and aqueous erosion of mild steel using electrochemical and dry sand impact techniques. In dry sand impact experiments, mild steel was eroded with 45 μm and 150 μm sand particles. Scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX) and micro-hardness techniques were used to elaborate the surface morphology of the eroded samples. The results revealed significant change in morphology of the eroded samples. In-depth analysis showed that although the metal erosion due to larger particles was significantly higher, the fines also notably damaged the metal surface. The surface damages were appreciably reduced with decrease in impact angle of the accelerated particles. The maximum damages were observed at an impact angle of 90°. The hardness of the samples treated with 45 μm and 150 μm sand remained in the range of 88.34 to 102.31 VHN and 87.7 to 97.55 VHN, respectively. In electrochemical experiments, a triple electrode probe was added into the metal treatment process. The linear polarization resistance (LPR) measurements were performed in slurries having 5% (by weight) of sand particles. LPR of the samples treated with 45 μm and 150 μm sand slurries was calculated about 949 Ω.cm(2) and 809 Ω.cm(2), respectively.

Dynamics of volcanic ash remobilisation by wind through the Patagonian steppe after the eruption of Cordón Caulle, 2011

PubMed Central

Panebianco, Juan E.; Mendez, Mariano J.; Buschiazzo, Daniel E.; Bran, Donaldo; Gaitán, Juan J.

2017-01-01

Wind erosion of freshly-deposited volcanic ash causes persistent storms, strongly affecting ecosystems and human activity. Wind erosion of the volcanic ash was measured up to 17 months after the ash deposition, at 7 sites located within the ash-deposition area. The mass flux was measured up to 1.5 m above ground level. Mass transport rates were over 125 times the soil wind-erosion rates observed before the ash deposition, reaching up to 6.3 kg m−1 day−1. Total mass transport of ash during the 17 months ranged between 113.6 and 969.9 kg m−1 depending on topographic location and wind exposure. The vertical distribution of the mass flux at sites with higher vegetation cover was generally inverted as compared to sites with lower vegetation cover. This situation lasted 7 months and then a shift towards a more uniform vertical distribution was observed, in coincidence with the beginning of the decline of the mass transport rates. Decay rates differed between sites. Despite changes over time, an inverse linear correlation between the mass transports and the mass-flux gradients was found. Both the mass-flux gradients and the average mass-transport rates were not linked with shear-stress partition parameters, but with the ratio: ash-fall thickness to total vegetation cover. PMID:28349929

Dynamics of volcanic ash remobilisation by wind through the Patagonian steppe after the eruption of Cordón Caulle, 2011.

PubMed

Panebianco, Juan E; Mendez, Mariano J; Buschiazzo, Daniel E; Bran, Donaldo; Gaitán, Juan J

2017-03-28

Wind erosion of freshly-deposited volcanic ash causes persistent storms, strongly affecting ecosystems and human activity. Wind erosion of the volcanic ash was measured up to 17 months after the ash deposition, at 7 sites located within the ash-deposition area. The mass flux was measured up to 1.5 m above ground level. Mass transport rates were over 125 times the soil wind-erosion rates observed before the ash deposition, reaching up to 6.3 kg m -1 day -1 . Total mass transport of ash during the 17 months ranged between 113.6 and 969.9 kg m -1 depending on topographic location and wind exposure. The vertical distribution of the mass flux at sites with higher vegetation cover was generally inverted as compared to sites with lower vegetation cover. This situation lasted 7 months and then a shift towards a more uniform vertical distribution was observed, in coincidence with the beginning of the decline of the mass transport rates. Decay rates differed between sites. Despite changes over time, an inverse linear correlation between the mass transports and the mass-flux gradients was found. Both the mass-flux gradients and the average mass-transport rates were not linked with shear-stress partition parameters, but with the ratio: ash-fall thickness to total vegetation cover.

Plasma-surface interaction in the Be/W environment: Conclusions drawn from the JET-ILW for ITER

NASA Astrophysics Data System (ADS)

Brezinsek, S.; JET-EFDA contributors

2015-08-01

The JET ITER-Like Wall experiment (JET-ILW) provides an ideal test bed to investigate plasma-surface interaction (PSI) and plasma operation with the ITER plasma-facing material selection employing beryllium in the main chamber and tungsten in the divertor. The main PSI processes: material erosion and migration, (b) fuel recycling and retention, (c) impurity concentration and radiation have be1en studied and compared between JET-C and JET-ILW. The current physics understanding of these key processes in the JET-ILW revealed that both interpretation of previously obtained carbon results (JET-C) and predictions to ITER need to be revisited. The impact of the first-wall material on the plasma was underestimated. Main observations are: (a) low primary erosion source in H-mode plasmas and reduction of the material migration from the main chamber to the divertor (factor 7) as well as within the divertor from plasma-facing to remote areas (factor 30 - 50). The energetic threshold for beryllium sputtering minimises the primary erosion source and inhibits multi-step re-erosion in the divertor. The physical sputtering yield of tungsten is low as 10-5 and determined by beryllium ions. (b) Reduction of the long-term fuel retention (factor 10 - 20) in JET-ILW with respect to JET-C. The remaining retention is caused by implantation and co-deposition with beryllium and residual impurities. Outgassing has gained importance and impacts on the recycling properties of beryllium and tungsten. (c) The low effective plasma charge (Zeff = 1.2) and low radiation capability of beryllium reveal the bare deuterium plasma physics. Moderate nitrogen seeding, reaching Zeff = 1.6 , restores in particular the confinement and the L-H threshold behaviour. ITER-compatible divertor conditions with stable semi-detachment were obtained owing to a higher density limit with ILW. Overall JET demonstrated successful plasma operation in the Be/W material combination and confirms its advantageous PSI behaviour and gives strong support to the ITER material selection.

Is the “ecological and economic approach for the restoration of collapsed gullies” in Southern China really economic?

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Chengchao; Zhang, Yaoqi; Xu, Yecheng

Collapsed gully erosion constantly plagues the sustainability of rural areas in China. To control collapsed gully erosion, an ecological and economic approach, which uses tree plantation to gain economic benefits and control soil erosion, has been widely applied by local governments in Southern China. However, little is known about the economic feasibility of this new method. The objective of this study was to determine the effectiveness and economic benefits of the new method. Based on a case study in Changting County, Southeast China, two farms were selected to represent a timber tree plantation and a fruit tree plantation, respectively. Themore » Annual Capital Capitalization Method and Return on Investment (ROI) were selected to conduct cost-benefit analysis. In contrast to previous studies, we found that the new approach was far from economic. The value of the newly-built forestland in Sanzhou Village and Tufang Village is 2738 RMB ha -1 and 5477 RMB ha -1, respectively, which are extremely lower than the costs of ecological restoration. Meanwhile, the annual ROI is –3.60% and –8.90%, respectively, which is negative and also far poorer than the average value of forestry in China. The costs of conservation were substantially over the related economic benefits, and the investors would suffer from greater loss if they invested more in the conservation. Low-cost terraces with timber trees had less economic loss compared with the costly terraces with fruit tree plantation. Moreover, the cost efficiency of the new approaches in soil conservation was also greatly poorer than the conventional method. The costs of conserving one ton soil per year for conventional method, new method for planting timber trees, and planting fruit trees were 164 RMB, 696 RMB, and 11,664 RMB, respectively. Therefore, the new collapsed gully erosion control methods are uneconomic and unsuitable to be widely carried out in China in the near future.« less

Is the “ecological and economic approach for the restoration of collapsed gullies” in Southern China really economic?

DOE PAGES

Wang, Chengchao; Zhang, Yaoqi; Xu, Yecheng; ...

2015-07-31

Collapsed gully erosion constantly plagues the sustainability of rural areas in China. To control collapsed gully erosion, an ecological and economic approach, which uses tree plantation to gain economic benefits and control soil erosion, has been widely applied by local governments in Southern China. However, little is known about the economic feasibility of this new method. The objective of this study was to determine the effectiveness and economic benefits of the new method. Based on a case study in Changting County, Southeast China, two farms were selected to represent a timber tree plantation and a fruit tree plantation, respectively. Themore » Annual Capital Capitalization Method and Return on Investment (ROI) were selected to conduct cost-benefit analysis. In contrast to previous studies, we found that the new approach was far from economic. The value of the newly-built forestland in Sanzhou Village and Tufang Village is 2738 RMB ha -1 and 5477 RMB ha -1, respectively, which are extremely lower than the costs of ecological restoration. Meanwhile, the annual ROI is –3.60% and –8.90%, respectively, which is negative and also far poorer than the average value of forestry in China. The costs of conservation were substantially over the related economic benefits, and the investors would suffer from greater loss if they invested more in the conservation. Low-cost terraces with timber trees had less economic loss compared with the costly terraces with fruit tree plantation. Moreover, the cost efficiency of the new approaches in soil conservation was also greatly poorer than the conventional method. The costs of conserving one ton soil per year for conventional method, new method for planting timber trees, and planting fruit trees were 164 RMB, 696 RMB, and 11,664 RMB, respectively. Therefore, the new collapsed gully erosion control methods are uneconomic and unsuitable to be widely carried out in China in the near future.« less

Suppression of elevated cartilage turnover in postmenopausal women and in ovariectomized rats by estrogen and a selective estrogen-receptor modulator (SERM).

PubMed

Christgau, Stephan; Tankó, László B; Cloos, Paul A C; Mouritzen, Ulrik; Christiansen, Claus; Delaissé, Jean-Marie; Høegh-Andersen, Pernille

2004-01-01

Several observational studies indicate that estrogen deficiency increases the incidence of osteoarthritis in postmenopausal women. To validate this observation, we investigated the effects of ovariectomy (OVX) on cartilage erosion in rats using histology and an established bio-assay of cartilage-specific collagen type II degradation products (CTX-II). Furthermore, we investigated whether estrogen and levormeloxifene, a selective estrogen-receptor modulator (SERM), can prevent the OVX-induced changes in cartilage degradation. The clinical relevance was assessed in postmenopausal women by measuring the changes in CTX-II during 12-month treatment with levormeloxifene versus placebo. Sixty 6-month-old rats were divided in five groups. One group was subjected to sham and the others to OVX, followed by treatment with vehicle alone, estradiol or 0.2 mg/kg/day or 5 mg/kg/day of levormeloxifene. The rats were treated for 9 weeks with biweekly blood and urine sampling for measurement of bone resorption and cartilage turnover. After study termination, hind knees were removed for histological analysis of erosions. The effect of levormeloxifene in post-menopausal women was assessed by measuring CTX-II in samples from 301 women who were participating in a phase II study of this SERM. OVX rats showed significant increases in the urinary excretion of CTX-II. After 9 weeks this was manifested as increased surface erosion of knee articular cartilage compared with sham-operated rats. Treatment with estrogen or levormeloxifene prevented the OVX-induced changes. There was a significant correlation between the 4-week changes in CTX-II and cartilage erosion at week 9 (r = 0.64, P < 0.001). In postmenopausal women treated with levormeloxifene, the urinary excretion of CTX-II was decreased by approximately 50% and restored CTX-II levels to the premenopausal range. This study is the first to demonstrate that a SERM suppresses cartilage degradation in both rodents and humans, suggesting potential therapeutical benefits in the prevention of destructive joint diseases such as osteoarthritis.

Human induced prehistoric and historical soil erosion and landscape development in Southwestern USA

NASA Astrophysics Data System (ADS)

Dotterweich, Markus; Ivester, Andrew H.; Hanson, Paul R.; Daniel, Larsen; Dye, David H.; Foster, Thomas H., II

2015-04-01

The significance of soil erosion due to pre-historic land use and possible feedback mechanisms had been hardly recognized in the Southeastern USA. Here, the agricultural practices only began in the second half of the Holocene. Sedentary hunters and gatherers started to domesticate squash and sunflowers. Associated with the expansion of maize cultivation in the Mississippian period between AD 800 and 1100, significant forest clearings took place on the river floodplains. During this time, central settlements with up to 30,000 residences existed and the surrounding ridge and furrow fields extended to up to 30 ha. It is still open to question why these groups already declined in the 14/15th centuries already before the arrival of the Europeans. However, around AD 1540 the conquistador de Soto still reports extended fields with intensive cultivation of maize in the uplands of Northern Mississippi. Despite of this intensive land use by Native Americans, current research gives no indication that these activities had any significant impact on river channel form. Also, no clear evidence exists for distinct channel change occurring in response to any sort of middle Holocene Hypsithermal, Medieval warm period, or the Little Ice Age. We will present results of a project which aims to explore erosion forms, colluvial sediments and buried soils in selected 0-order and 1st-order watersheds in the southeastern USA in order to gain, solidify, and evaluate general data on soil erosion during the Native American land use period and its respective long-term effects on the environment. This will be achieved by 1) recording the stratigraphy of colluvial and alluvial sediments and buried soils, 2) mapping the extent of erosional and colluvial forms, 3) analyzing chemical and physical soil and sediment properties, 4) establishing chronological control using various dating techniques including radiocarbon and OSL dating, and 5) quantifying soil erosion using hillslope sediments. The gathered data will be used to i) compare the spatial extent of prehistoric and historic erosion and the short-term and long-term pedological and geomorphological effects of subtle soil erosion against extreme events, ii) assess the feedback-mechanisms of soil erosion on soil fertility and measurable land use changes in prehistorical and historical times, and (iii) estimate the long term effects of soil erosion and sediment deposition on archaeological features. The outcome will provide a decisive step forward to gather new qualitative and quantitative information on soil erosion during the Native American land use period to be able to achieve a better understanding of the long-term human induced landscape evolution in the uplands of the Southeastern USA and deliver data for a better predicting of landscape evolution to future climatic shifts in precipitation regimes.

Comparison of morphological and conventional edge detectors in medical imaging applications

NASA Astrophysics Data System (ADS)

Kaabi, Lotfi; Loloyan, Mansur; Huang, H. K.

1991-06-01

Recently, mathematical morphology has been used to develop efficient image analysis tools. This paper compares the performance of morphological and conventional edge detectors applied to radiological images. Two morphological edge detectors including the dilation residue found by subtracting the original signal from its dilation by a small structuring element, and the blur-minimization edge detector which is defined as the minimum of erosion and dilation residues of the blurred image version, are compared with the linear Laplacian and Sobel and the non-linear Robert edge detectors. Various structuring elements were used in this study: regular 2-dimensional, and 3-dimensional. We utilized two criterions for edge detector's performance classification: edge point connectivity and the sensitivity to the noise. CT/MR and chest radiograph images have been used as test data. Comparison results show that the blur-minimization edge detector, with a rolling ball-like structuring element outperforms other standard linear and nonlinear edge detectors. It is less noise sensitive, and performs the most closed contours.

Screening study of select cotton-based hydromulch blends produced using the cross-linked biofiber process

USDA-ARS?s Scientific Manuscript database

As global populations continue to expand, stresses placed on our renewable resources are increasing. Disturbance of native landscapes from agriculture, urbanization, or by natural evolution brings the potential for soil erosion caused by normal rain events. Increasing regulatory pressure has resulte...

The development of novel and non-invasive germplasm selections native to Arkansas for highway re-vegetation projects.

DOT National Transportation Integrated Search

2012-03-01

"Re-vegetation strategies and programs for highway rights of way in both rural and urban areas are an importatn component of any : highway construction project. Vegetation is ued to stabilize soils to prevent sheet and gully erosion and to help in so...

The new conversion model MODERN to derive erosion rates from inventories of fallout radionuclides

NASA Astrophysics Data System (ADS)

Arata, Laura; Meusburger, Katrin; Frenkel, Elena; A'Campo-Neuen, Annette; Iurian, Andra-Rada; Ketterer, Michael E.; Mabit, Lionel; Alewell, Christine

2016-04-01

The measurement of fallout radionuclides (FRNs) has become one of the most commonly used methods to quantify soil erosion and depositional processes. FRNs include anthropogenic radionuclides (e.g. 137Cs, 239+240Pu) released into the atmosphere during nuclear bomb tests and power plant accidents (e.g Chernobyl, Fukushima-Daiichi), as well as natural radiotracers such as 210Pbex and 7Be. FRNs reach the land surface by dry and wet fallouts from the atmosphere. Once deposited, FRNs are tightly adsorbed by fine soil particles and their subsequent redistribution is mostly associated with soil erosion processes. FRNs methods are based on a qualitative comparison: the inventory (total radionuclide activity per unit area) at a given sampling site is compared to that of a so called reference site. The conversion of FRN inventories into soil erosion and deposition rates is done with a variety of models, which suitability is dependent on the selected FRN, soil cultivation (ploughed or unploughed) and movement (erosion or deposition). The authors propose a new conversion model, which can be easily and comprehensively used for different FRNs, land uses and soil redistribution processes. This new model i.e. MODERN (MOdelling Deposition and Erosion rates with RadioNuclides) considers the precise depth distribution of a given FRN at a reference site, and allows adapting it for any specific site conditions. MODERN adaptability and performance has been tested on two published case studies: (i) a 137Cs study in an alpine and unploughed area in the Aosta valley (Italy) and (ii) a 210Pbex study on a ploughed area located in Romania. The results show a good agreement and a significant correlation (r= 0.91, p<0.0001) between the results of MODERN and the published models currently used by the FRN scientific community (i.e. the Profile Distribution Model and the Mass Balance Model). The open access code and the cost free accessibility of MODERN will ensure the promotion of a wider application of FRNs for investigating soil erosion and sedimentation processes.

Erosion processes in molassic cliffs: the role of the rock surface temperature and atmospheric conditions

NASA Astrophysics Data System (ADS)

Carrea, Dario; Abellán, Antonio; Guerin, Antoine; Jaboyedoff, Michel; Voumard, Jérémie

2014-05-01

The morphology of the Swiss Plateau is modeled by numerous steep cliffs of Molasse. These cliffs are mainly composed of sub-horizontal alternated layers of sandstone, shale and conglomerates deposed in the Alps foreland basin during the Tertiary period. These Molasse cliffs are affected by erosion processes inducing numerous rockfall events. Thus, it is relevant to understand how different external factors influence Molasse erosion rates. In this study, we focus on analyzing temperature variation during a winter season. As pilot study area we selected a cliff which is formed by a sub-horizontal alternation of outcropping sandstone and shale. The westward facing test site (La Cornalle, Vaud, Switzerland), which is a lateral scarp of a slow moving landslide area, is currently affected by intense erosion. Regarding data acquisition, we monitored both in-situ rock and air temperatures at 15 minutes time-step since October 2013: (1) on the one hand we measured Ground Surface Temperature (GST) at near-surface (0.1 meter depth) using a GST mini-datalogger M-Log5W-Rock model; (2) On the other hand we monitored atmospheric conditions using a weather station (Davis Vantage pro2 plus) collecting numerous parameters (i.e. temperature, irradiation, rain, wind speed, etc.). Furthermore, the area was also seasonally monitored by Ground-Based (GB) LiDAR since 2010 and monthly monitored since September 2013. In order to understand how atmospheric conditions (such as freeze and thaw effect) influence the erosion of the cliff, we modeled the temperature diffusion through the rock mass. To this end, we applied heat diffusion and radiation equation using a 1D temperature profile, obtaining as a result both temperature variations at different depths together with the location of the 0°C isotherm. Our model was calibrated during a given training set using both in-situ rock temperatures and atmospheric conditions. We then carried out a comparison with the rockfall events derived from the 3D GB-LiDAR datasets in order to quantify the erosion rates and to correlate it with atmospheric conditions, aiming to analyze which parameters influence Molasse erosion process.

Erosion processes by water in agricultural landscapes: a low-cost methodology for post-event analyses

NASA Astrophysics Data System (ADS)

Prosdocimi, Massimo; Calligaro, Simone; Sofia, Giulia; Tarolli, Paolo

2015-04-01

Throughout the world, agricultural landscapes assume a great importance, especially for supplying food and a livelihood. Among the land degradation phenomena, erosion processes caused by water are those that may most affect the benefits provided by agricultural lands and endanger people who work and live there. In particular, erosion processes that affect the banks of agricultural channels may cause the bank failure and represent, in this way, a severe threat to floodplain inhabitants and agricultural crops. Similarly, rills and gullies are critical soil erosion processes as well, because they bear upon the productivity of a farm and represent a cost that growers have to deal with. To estimate quantitatively soil losses due to bank erosion and rills processes, area based measurements of surface changes are necessary but, sometimes, they may be difficult to realize. In fact, surface changes due to short-term events have to be represented with fine resolution and their monitoring may entail too much money and time. The main objective of this work is to show the effectiveness of a user-friendly and low-cost technique that may even rely on smart-phones, for the post-event analyses of i) bank erosion affecting agricultural channels, and ii) rill processes occurring on an agricultural plot. Two case studies were selected and located in the Veneto floodplain (northeast Italy) and Marche countryside (central Italy), respectively. The work is based on high-resolution topographic data obtained by the emerging, low-cost photogrammetric method named Structure-from-Motion (SfM). Extensive photosets of the case studies were obtained using both standalone reflex digital cameras and smart-phone built-in cameras. Digital Terrain Models (DTMs) derived from SfM revealed to be effective to estimate quantitatively erosion volumes and, in the case of the bank eroded, deposited materials as well. SfM applied to pictures taken by smartphones is useful for the analysis of the topography and Earth surface processes at very low-cost. This methodology should be of great help for farmers and/or technician who work at Land Reclamation Consortia or at Civil Protection for taking suitable post-event field surveys in support to flood risk and soil management.

[Mechanisms of grass in slope erosion control in Loess sandy soil region of Northwest China].

PubMed

Zhao, Chun-Hong; Gao, Jian-En; Xu, Zhen

2013-01-01

By adopting the method of simulated precipitation and from the viewpoint of slope hydrodynamics, in combining with the analysis of soil resistance to erosion, a quantitative study was made on the mechanisms of grass in controlling the slope erosion in the cross area of wind-water erosion in Loess Plateau of Northwest China under different combinations of rainfall intensity and slope gradient, aimed to provide basis to reveal the mechanisms of vegetation in controlling soil erosion and to select appropriate vegetation for the soil and water conservation in Loess Plateau. The grass Astragalus adsurgens with the coverage about 40% could effectively control the slope erosion. This grass had an efficiency of more than 70% in reducing sediment, and the grass root had a greater effect than grass canopy. On bare slope and on the slopes with the grass plant or only the grass root playing effect, there existed a functional relation between the flow velocity on the slopes and the rainfall intensity and slope gradient (V = DJ(0.33 i 0.5), where V is flow velocity, D is the comprehensive coefficient which varies with different underlying surfaces, i is rainfall intensity, and J is slope gradient). Both the grass root and the grass canopy could markedly decrease the flow velocity on the slopes, and increase the slope resistance, but the effect of grass root in decreasing flow velocity was greater while the effect in increasing resistance was smaller than that of grass canopy. The effect of grass root in increasing slope resistance was mainly achieved by increasing the sediment grain resistance, while the effect of canopy was mainly achieved by increasing the slope form resistance and wave resistance. The evaluation of the soil resistance to erosion by using a conceptual model of sediment generation by overland flow indicated that the critical shear stress value of bare slope and of the slopes with the grass plant or only the grass root playing effect was 0.533, 1.672 and 0.925 Pa, respectively.

Effectiveness of prescribed fire to re-establish sagebrush vegetation and ecohydrologic function on woodland-encroached sagebrush steppe, Great Basin, USA

NASA Astrophysics Data System (ADS)

Williams, C. J.; Pierson, F. B.; Kormos, P.; Al-Hamdan, O. Z.; Nouwakpo, S.; Weltz, M.; Vega, S.; Lindsay, K.

2017-12-01

Range expansion of pinyon (Pinus spp.) and juniper (Juniperus spp.) conifers into sagebrush steppe (Artemisia spp.) communities has imperiled a vast domain in the western US. Encroachment of sagebrush ecosystems by pinyon and juniper conifers has negative ramifications to ecosystem structure and function and delivery of goods and services. Scientists, land management agencies, and private land owners throughout the western US are challenged with selecting from a suite of options to reduce pinyon and juniper woody fuels and re-establish sagebrush steppe structure and function. This study evaluated the effectiveness of prescribed fire to re-establish sagebrush vegetation and ecohydrologic function over a 9 yr period. Nine years post-fire hydrologic and erosion responses reflect the combination of pre-fire site conditions, perennial grass recruitment, delayed litter cover, and inherent site characteristics. Burning initially increased bare ground, runoff, and erosion for well-vegetated areas underneath tree and shrub canopies, but had minimal impact on hydrology and erosion for degraded interspaces between plants. The degraded interspaces were primarily bare ground and exhibited high runoff and erosion rates prior to burning. Initial fire effects persisted for two years, but increased productivity of grasses improved hydrologic function of interspaces over the full 9 yr period. At the hillslope scale, grass recruitment in the intercanopy between trees reduced runoff from rainsplash, sheetflow, and concentrated overland flow at one site, but did not reduce the high levels of runoff and erosion from a more degraded site. In areas formerly occupied by trees (tree zones), burning increased invasive annual grass cover due to fire removal of limited native perennial plants and competition for resources. The invasive annual grass cover had no net effect on runoff and erosion from tree zones however. Runoff and erosion increased in tree zones at the more degraded site due to delayed litter recruitment and persistence of bare ground conditions. Overall, the 9 yr study illustrates the ecohydrologic complexities with predicting sagebrush ecosystem responses to woodland encroachment and tree removal.

Modeling Long-Term Fluvial Incision : Shall we Care for the Details of Short-Term Fluvial Dynamics?

NASA Astrophysics Data System (ADS)

Lague, D.; Davy, P.

2008-12-01

Fluvial incision laws used in numerical models of coupled climate, erosion and tectonics systems are mainly based on the family of stream power laws for which the rate of local erosion E is a power function of the topographic slope S and the local mean discharge Q : E = K Qm Sn. The exponents m and n are generally taken as (0.35, 0.7) or (0.5, 1), and K is chosen such that the predicted topographic elevation given the prevailing rates of precipitation and tectonics stay within realistic values. The resulting topographies are reasonably realistic, and the coupled system dynamics behaves somehow as expected : more precipitation induces increased erosion and localization of the deformation. Yet, if we now focus on smaller scale fluvial dynamics (the reach scale), recent advances have suggested that discharge variability, channel width dynamics or sediment flux effects may play a significant role in controlling incision rates. These are not factored in the simple stream power law model. In this work, we study how these short- term details propagate into long-term incision dynamics within the framework of surface/tectonics coupled numerical models. To upscale the short term dynamics to geological timescales, we use a numerical model of a trapezoidal river in which vertical and lateral incision processes are computed from fluid shear stress at a daily timescale, sediment transport and protection effects are factored in, as well as a variable discharge. We show that the stream power law model might still be a valid model but that as soon as realistic effects are included such as a threshold for sediment transport, variable discharge and dynamic width the resulting exponents m and n can be as high as 2 and 4. This high non-linearity has a profound consequence on the sensitivity of fluvial relief to incision rate. We also show that additional complexity does not systematically translates into more non-linear behaviour. For instance, considering only a dynamical width without discharge variability does not induce a significant difference in the predicted long-term incision law and scaling of relief with incision rate at steady-state. We conclude that the simple stream power law models currently in use are false, and that details of short-term fluvial dynamics must make their way into long-term evolution models to avoid oversimplifying the coupled dynamics between erosion, tectonics and climate.

Mapping Shoreline Change Using Digital Orthophotogrammetry on Maui, Hawaii

USGS Publications Warehouse

Fletcher, C.; Rooney, J.; Barbee, M.; Lim, S.-C.; Richmond, B.

2003-01-01

Digital, aerial orthophotomosaics with 0.5-3.0 m horizontal accuracy, used with NOAA topographic maps (T-sheets), document past shoreline positions on Maui Island, Hawaii. Outliers in the shoreline position database are determined using a least median of squares regression. Least squares linear regression of the reweighted data (outliers excluded) is used to determine a shoreline trend termed the reweighted linear squares (RLS). To determine the annual erosion hazard rate (AEHR) for use by shoreline managers the RLS data is smoothed in the longshore direction using a weighted moving average five transects wide with the smoothed rate applied to the center transect. Weightings within each five transect group are 1,3,5,3,1. AEHR's (smoothed RLS values) are plotted on a 1:3000 map series for use by shoreline managers and planners. These maps are displayed on the web for public reference at http://www.co.maui.hi.us/ departments/Planning/erosion.htm. An end-point rate of change is also calculated using the earliest T-sheet and the latest collected shoreline (1997 or 2002). The resulting database consists of 3565 separate erosion rates spaced every 20 m along 90 km of sandy shoreline. Three regions are analyzed: Kihei, West Maui, and North Shore coasts. The Kihei Coast has an average AEHR of about 0.3 m/yr, an end point rate (EPR) of 0.2 m/yr, 2.8 km of beach loss and 19 percent beach narrowing in the period 1949-1997. Over the same period the West Maui coast has an average AEHR of about 0.2 m/yr, an average EPR of about 0.2 m/yr, about 4.5 km of beach loss and 25 percent beach narrowing. The North Shore has an average AEHR of about 0.4 m/yr, an average EPR of about 0.3 m/yr, 0.8 km of beach loss and 15 percent beach narrowing. The mean, island-wide EPR of eroding shorelines is 0.24 m/yr and the average AEHR of eroding shorelines is about 0.3 m/yr. The overall shoreline change rate, erosion and accretion included, as measured using the unsmoothed RLS technique is 0.21 m/yr. Island wide changes in beach width show a 19 percent decrease over the period 1949/ 1950 to 1997/2002. Island-wide, about 8 km of dry beach has been lost since 1949 (i.e., high water against hard engineering structures and natural rock substrate).

Comparative Study of SVM Methods Combined with Voxel Selection for Object Category Classification on fMRI Data

PubMed Central

Song, Sutao; Zhan, Zhichao; Long, Zhiying; Zhang, Jiacai; Yao, Li

2011-01-01

Background Support vector machine (SVM) has been widely used as accurate and reliable method to decipher brain patterns from functional MRI (fMRI) data. Previous studies have not found a clear benefit for non-linear (polynomial kernel) SVM versus linear one. Here, a more effective non-linear SVM using radial basis function (RBF) kernel is compared with linear SVM. Different from traditional studies which focused either merely on the evaluation of different types of SVM or the voxel selection methods, we aimed to investigate the overall performance of linear and RBF SVM for fMRI classification together with voxel selection schemes on classification accuracy and time-consuming. Methodology/Principal Findings Six different voxel selection methods were employed to decide which voxels of fMRI data would be included in SVM classifiers with linear and RBF kernels in classifying 4-category objects. Then the overall performances of voxel selection and classification methods were compared. Results showed that: (1) Voxel selection had an important impact on the classification accuracy of the classifiers: in a relative low dimensional feature space, RBF SVM outperformed linear SVM significantly; in a relative high dimensional space, linear SVM performed better than its counterpart; (2) Considering the classification accuracy and time-consuming holistically, linear SVM with relative more voxels as features and RBF SVM with small set of voxels (after PCA) could achieve the better accuracy and cost shorter time. Conclusions/Significance The present work provides the first empirical result of linear and RBF SVM in classification of fMRI data, combined with voxel selection methods. Based on the findings, if only classification accuracy was concerned, RBF SVM with appropriate small voxels and linear SVM with relative more voxels were two suggested solutions; if users concerned more about the computational time, RBF SVM with relative small set of voxels when part of the principal components were kept as features was a better choice. PMID:21359184

Comparative study of SVM methods combined with voxel selection for object category classification on fMRI data.

PubMed

Song, Sutao; Zhan, Zhichao; Long, Zhiying; Zhang, Jiacai; Yao, Li

2011-02-16

Support vector machine (SVM) has been widely used as accurate and reliable method to decipher brain patterns from functional MRI (fMRI) data. Previous studies have not found a clear benefit for non-linear (polynomial kernel) SVM versus linear one. Here, a more effective non-linear SVM using radial basis function (RBF) kernel is compared with linear SVM. Different from traditional studies which focused either merely on the evaluation of different types of SVM or the voxel selection methods, we aimed to investigate the overall performance of linear and RBF SVM for fMRI classification together with voxel selection schemes on classification accuracy and time-consuming. Six different voxel selection methods were employed to decide which voxels of fMRI data would be included in SVM classifiers with linear and RBF kernels in classifying 4-category objects. Then the overall performances of voxel selection and classification methods were compared. Results showed that: (1) Voxel selection had an important impact on the classification accuracy of the classifiers: in a relative low dimensional feature space, RBF SVM outperformed linear SVM significantly; in a relative high dimensional space, linear SVM performed better than its counterpart; (2) Considering the classification accuracy and time-consuming holistically, linear SVM with relative more voxels as features and RBF SVM with small set of voxels (after PCA) could achieve the better accuracy and cost shorter time. The present work provides the first empirical result of linear and RBF SVM in classification of fMRI data, combined with voxel selection methods. Based on the findings, if only classification accuracy was concerned, RBF SVM with appropriate small voxels and linear SVM with relative more voxels were two suggested solutions; if users concerned more about the computational time, RBF SVM with relative small set of voxels when part of the principal components were kept as features was a better choice.

Comprehensive study of the abrasive wear and slurry erosion behavior of an expanded system of high chromium cast iron and microstructural modification for enhanced wear resistance

NASA Astrophysics Data System (ADS)

Chung, Reinaldo Javier

High chromium cast irons (HCCIs) have been demonstrated to be an effective material for a wide range of applications in aggressive environments, where resistances to abrasion, erosion and erosion-corrosion are required. For instance, machinery and facilities used in mining and extraction in Alberta's oil sands suffer from erosion and erosion-corrosion caused by silica-containing slurries, which create challenges for the reliability and maintenance of slurry pumping systems as well as other processing and handling equipment. Considerable efforts have been made to determine and understand the relationship between microstructural features of the HCCIs and their wear performance, in order to guide the material selection and development for specific service conditions with optimal performance. The focus was previously put on a narrow group of compositions dictated by ASTM A532. However, with recent advances in casting technology, the HCCI compositional range can be significantly expanded, which potentially brings new alloys that can be superior to those which are currently employed. This work consists of three main aspects of study. The first one is the investigation of an expanded system of white irons with their composition ranging from 1 to 6 wt.% C and 5 to 45 wt.% Cr, covering 53 alloys. This work has generated wear and corrosion maps and established correlation between the performance and microstructural features for the alloys. The work was conducted in collaboration with the Materials Development Center of Weir Minerals in Australia, and the results have been collected in a database that is used by the company to guide materials selection for slurry pump components in Alberta oil sands and in other mining operations throughout the world. The second part consists of three case studies on effects of high chromium and high carbon, respectively, on the performance of the HCCIs. The third aspect is the development of an approach to enhance the wear resistance of HCCIs by microstructural modification through addition of strong carbide-forming elements to produce eutectic microstructures reinforced with in-situ formed foreign carbides. Very promising results have been obtained in lab, which demonstrates that the approach is feasible and effective in tailoring HCCIs for improved performance.

Performance mapping of a 30 cm engineering model thruster

NASA Technical Reports Server (NTRS)

Poeschel, R. L.; Vahrenkamp, R. P.

1975-01-01

A 30 cm thruster representative of the engineering model design has been tested over a wide range of operating parameters to document performance characteristics such as electrical and propellant efficiencies, double ion and beam divergence thrust loss, component equilibrium temperatures, operational stability, etc. Data obtained show that optimum power throttling, in terms of maximum thruster efficiency, is not highly sensitive to parameter selection. Consequently, considerations of stability, discharge chamber erosion, thrust losses, etc. can be made the determining factors for parameter selection in power throttling operations. Options in parameter selection based on these considerations are discussed.

Pristine and Surface-Modified Polymers in LEO: MISSE Results versus Predictive Models and Ground-Based Testing

NASA Astrophysics Data System (ADS)

Iskanderova, Zelina; Kleiman, Jacob I.; Tennyson, Rod C.

2009-01-01

Space flight data, collected and published by NASA Glenn Research Center (GRC) team for a set of pristine polymeric materials selected, compiled, and tested in two LEO flight experiments at the International Space Station, as part of the "Materials International Space Station Experiment" (MISSE), has been used for comparison with previously developed atomic oxygen erosion predictive models. The same set of materials was used for a ground-based fast atomic beam (FAO) experimental erosion study at ITL/UTIAS, where the FAO exposure was performed mostly at a standard fluence of 2×1020 cm-2, with the results collected in a database for the development of a prototype of predictive software. A comparison of MISSE-1 flight data with two predictive correlations has shown good agreement, confirming the developed approach to polymers erosion resistance forecast that might be used also for newly developed or untested in space polymeric materials. A number of surface-modified thin film space polymers, treated by two ITL-developed and patented surface modification technologies, Implantox™ [5] and Photosil™ [6], have been also included in MISSE flight experiment. The results from those MISSE samples have shown full protection of AO-sensitive main space-related hydrocarbon polymers, such as Kapton HN, back-metalized Kapton H and Kapton E, and Mylar, when treated by Implantox™ surface modification technology and significant erosion resistance enhancement up to full protection by Photosil™ treatment.

St. Louis Metro East region sediment and geomorphic study

USGS Publications Warehouse

Straub, T.D.; ,

2004-01-01

Judy's Branch, a small basin (8.64 mi2) near Glen Carbon, Illinois, is selected as a pilot site to determine sediment yield and channel erosion of streams draining the bluffs of the American Bottoms in the Metro East area of Illinois. This paper presents results of an on-going sediment and geomorphic study in Judy's Branch. The average suspended-sediment yield from two upland sub-basins (drainage area equals 0.23 and 0.40 miles2) is 851 tons/mile2-year between October 2000 and September 2003. The suspended-sediment yield at the Route 157 gage (2,188 tons/mile 2-year) (near outlet of the watershed; drainage area = 8.33 miles2) is approximately 1300 tons/mile2-year greater than the average of the upland gages for the same time period. This result is unexpected in that generally the suspended-sediment yield decreases as the watershed area increases because of sediment being stored in the channel and floodplain. The difference indicates a possible increase in yield from a source, such as streambank erosion, and supports the theory that land-use changes increase streamflows that may result in higher rates of streambank erosion. The best estimate of sediment yield from streambank erosion is 1,009 tons/mile 2-year at Route 157. This value is obtained utilizing both bank-rod data and resurveyed cross-section data.

Wear resistance and mechanisms of composite hardfacings at abrasive impact erosion wear

NASA Astrophysics Data System (ADS)

Surzhenkov, A.; Viljus, M.; Simson, T.; Tarbe, R.; Saarna, M.; Casesnoves, F.

2017-05-01

Tungsten carbide based hardmetal containing sprayed and melted composite hardfacings are prospective for protection against abrasive wear. For selection of abrasive wear resistant hardfacings under intensive impact wear conditions, both mechanical properties (hardness, fracture toughness, etc.) and abrasive wear conditions (type of abrasive, impact velocity, etc.) should be considered. This study focuses on the wear (wear rate and mechanisms) of thick metal-matrix composite hardfacings with hardmetal (WC-Co) reinforcement produced by powder metallurgy technology. The influence of the hardmetal reinforcement type on the wear resistance at different abrasive impact erosion wear (AIEW) conditions was studied. An optimal reinforcement for various wear conditions is described. Based on wear mechanism studies, a mathematical model for wear prediction was drafted.

Surface erosion at disturbed alpine sites: effects of vegetation cover and plant diversity

NASA Astrophysics Data System (ADS)

Martin, C.; Pohl, M.; Alewell, C.; Körner, C.; Buttler, A.; Rixen, C.

2009-04-01

The relationship between plant diversity and soil stability in disturbed alpine terrain is poorly studied. In this paper, we investigated the influence of plant cover and diversity on water run-off and sediment yield on ski slopes. Rainfall simulations were conducted on a micro-scale (25 x 25 cm) to be able to replicate plots with different degrees of vegetation cover. We selected plots with 10%, 30% and 60% of vegetation cover containing different combinations of plant diversities: (i) grass, (ii) herb, (iii) moss/ lichen, and all combinations of these plant groups. Each combination was replicated five times with an applied rain intensity of 375 ml min-1 for about 5 minutes. As could be expected, percent vegetation cover had a large effect on surface erosion: sediment yield decreased with increasing vegetation cover. However, within the plots with 60% cover, sediment yield was lower at higher plant diversity and functional group diversity. The findings of this study support the view that beside the re-establishment of a closed vegetation cover, plant diversity is a relevant factor to reduce surface erosion at disturbed sites in alpine ecosystems.

Field studies of beach cones as coastal erosion control/reversal devices for areas with significant oil and gas activities. [Annual report], February 24, 1992--February 23, 1993

DOE Office of Scientific and Technical Information (OSTI.GOV)

Law, V.J.

1993-03-15

The primary objective of this project is to evaluate the utility of a device called the ``beach cone`` in combating coastal erosion. Seven initial sites were selected for testing beach cones in a variety of geometric configurations. Permits were obtained from the State of Louisiana and the US Army Corps of Engineers to perform the work associated with this study. Six hundred beach cones were actually installed at six of the sites in late July and early August, 1992. One of the initial sites was abandoned because it was found to be unsuitable for beach cone placement. The test sitesmore » have been observed for six months and preliminary findings indicate that beach cones accreted significant amounts of materials along the beach of a barrier island. At other test sites, accretion rates have been less dramatic but importantly, no significant additional erosion has occurred, which is a positive result. It is too soon to state the categorical success of the beach cones, but results to date are encouraging.« less

Linear and nonlinear variable selection in competing risks data.

PubMed

Ren, Xiaowei; Li, Shanshan; Shen, Changyu; Yu, Zhangsheng

2018-06-15

Subdistribution hazard model for competing risks data has been applied extensively in clinical researches. Variable selection methods of linear effects for competing risks data have been studied in the past decade. There is no existing work on selection of potential nonlinear effects for subdistribution hazard model. We propose a two-stage procedure to select the linear and nonlinear covariate(s) simultaneously and estimate the selected covariate effect(s). We use spectral decomposition approach to distinguish the linear and nonlinear parts of each covariate and adaptive LASSO to select each of the 2 components. Extensive numerical studies are conducted to demonstrate that the proposed procedure can achieve good selection accuracy in the first stage and small estimation biases in the second stage. The proposed method is applied to analyze a cardiovascular disease data set with competing death causes. Copyright © 2018 John Wiley & Sons, Ltd.

Field measurement of basal forces generated by erosive debris flows

USGS Publications Warehouse

McCoy, S.W.; Tucker, G.E.; Kean, J.W.; Coe, J.A.

2013-01-01

It has been proposed that debris flows cut bedrock valleys in steeplands worldwide, but field measurements needed to constrain mechanistic models of this process remain sparse due to the difficulty of instrumenting natural flows. Here we present and analyze measurements made using an automated sensor network, erosion bolts, and a 15.24 cm by 15.24 cm force plate installed in the bedrock channel floor of a steep catchment. These measurements allow us to quantify the distribution of basal forces from natural debris‒flow events that incised bedrock. Over the 4 year monitoring period, 11 debris‒flow events scoured the bedrock channel floor. No clear water flows were observed. Measurements of erosion bolts at the beginning and end of the study indicated that the bedrock channel floor was lowered by 36 to 64 mm. The basal force during these erosive debris‒flow events had a large‒magnitude (up to 21 kN, which was approximately 50 times larger than the concurrent time‒averaged mean force), high‒frequency (greater than 1 Hz) fluctuating component. We interpret these fluctuations as flow particles impacting the bed. The resulting variability in force magnitude increased linearly with the time‒averaged mean basal force. Probability density functions of basal normal forces were consistent with a generalized Pareto distribution, rather than the exponential distribution that is commonly found in experimental and simulated monodispersed granular flows and which has a lower probability of large forces. When the bed sediment thickness covering the force plate was greater than ~ 20 times the median bed sediment grain size, no significant fluctuations about the time‒averaged mean force were measured, indicating that a thin layer of sediment (~ 5 cm in the monitored cases) can effectively shield the subjacent bed from erosive impacts. Coarse‒grained granular surges and water‒rich, intersurge flow had very similar basal force distributions despite differences in appearance and bulk‒flow density. These results demonstrate that debris flows can have strong control on rates of steepland evolution and contribute to a foundation needed for modeling debris‒flow incision stochastically.

Combined Tin-Containing Fluoride Solution and CO2 Laser Treatment Reduces Enamel Erosion in vitro.

PubMed

Esteves-Oliveira, Marcella; Witulski, Nadine; Hilgers, Ralf-Dieter; Apel, Christian; Meyer-Lueckel, Hendrik; Eduardo, Carlos de Paula

2015-01-01

The aim of this in vitro study was to evaluate the effect of combined CO2 laser and tin-containing fluoride treatment on the formation and progression of enamel erosive lesions. Ninety-six human enamel samples were obtained, stored in thymol solution and, after surface polishing, randomly divided into 6 different surface treatment groups (n = 16 in each group) as follows: no treatment, control (C); one CO2 laser irradiation (L1); two CO2 laser irradiations (L2); daily application of fluoride solution (F); combined daily fluoride solution + one CO2 laser irradiation (L1F), and combined daily fluoride solution + two CO2 laser irradiations (L2F). Laser irradiation was performed at 0.3 J/cm2 (5 µs/226 Hz/10.6 µm) on day 1 (L1) and day 6 (L2). The fluoride solution contained AmF/NaF (500 ppm F), and SnCl2 (800 ppm Sn) at pH 4.5. After surface treatment the samples were submitted to an erosive cycling over 10 days, including immersion in citric acid (2 min/0.05 M/pH = 2.3) 6 times daily and storage in remineralization solution (≥1 h) between erosive attacks. At the end of each cycling day, the enamel surface loss (micrometers) was measured using a 3D laser profilometer. Data were statistically analyzed by means of a 2-level mixed effects model and linear contrasts (α = 0.05). Group F (-3.3 ± 2.0 µm) showed significantly lower enamel surface loss than groups C (-27.22 ± 4.1 µm), L1 (-18.3 ± 4.4 µm) and L2 (-16.3 ± 5.3 µm) but higher than L1F (-1.0 ± 4.4 µm) and L2F (1.4 ± 3.2 µm, p < 0.05). Under the conditions of this in vitro study, the tin-containing fluoride solution caused 88% reduction of enamel surface loss, while its combination with CO2 laser irradiation at 0.3 J/cm2 hampered erosive loss almost completely. © 2015 S. Karger AG, Basel.

Image processing for IMRT QA dosimetry.

PubMed

Zaini, Mehran R; Forest, Gary J; Loshek, David D

2005-01-01

We have automated the determination of the placement location of the dosimetry ion chamber within intensity-modulated radiotherapy (IMRT) fields, as part of streamlining the entire IMRT quality assurance process. This paper describes the mathematical image-processing techniques to arrive at the appropriate measurement locations within the planar dose maps of the IMRT fields. A specific spot within the found region is identified based on its flatness, radiation magnitude, location, area, and the avoidance of the interleaf spaces. The techniques used include applying a Laplacian, dilation, erosion, region identification, and measurement point selection based on three parameters: the size of the erosion operator, the gradient, and the importance of the area of a region versus its magnitude. These three parameters are adjustable by the user. However, the first one requires tweaking in extremely rare occasions, the gradient requires rare adjustments, and the last parameter needs occasional fine-tuning. This algorithm has been tested in over 50 cases. In about 5% of cases, the algorithm does not find a measurement point due to the extremely steep and narrow regions within the fluence maps. In such cases, manual selection of a point is allowed by our code, which is also difficult to ascertain, since the fluence map does not yield itself to an appropriate measurement point selection.

CT venography: use in selecting a surgical approach for the treatment of petrous apex cholesterol granulomas.

PubMed

Isaacson, Brandon; Kutz, Joe Walter; Mendelsohn, Dianne; Roland, Peter S

2009-04-01

To demonstrate the use of computed tomographic (CT) venography in selecting a surgical approach for cholesterol granulomas. Retrospective case review. Tertiary referral center. Three patients presented with symptomatic petrous apex cholesterol granulomas with extensive bone erosion involving the jugular fossa. Computed tomographic venography was performed on each patient before selecting a surgical approach for drainage. Localization of the jugular bulb in relation to the petrous carotid artery and basal turn of the cochlea was ascertained in each subject. Three patients with large symptomatic cholesterol granulomas were identified. Conventional CT demonstrated extensive bone erosion involving the jugular fossa in each patient. The location of the jugular bulb and its proximity to the petrous carotid artery and basal turn of the cochlea could not be determined with conventional temporal bone CT and magnetic resonance imaging. Computed tomographic venography provided the exact location of the jugular bulb in all 3 patients. The favorable position of the jugular bulb in all 3 cases permitted drainage of these lesions using an infracochlear approach. Computed tomographic venography provided invaluable information in 3 patients with large symptomatic cholesterol granulomas. All 3 patients were previously thought to be unsuitable candidates for an infracochlear or infralabyrinthine approach because of the unknown location of the jugular bulb.

Genetic evaluation of claw health traits accounting for potential preselection of cows to be trimmed.

PubMed

Croué, Iola; Fikse, Freddy; Johansson, Kjell; Carlén, Emma; Thomas, Gilles; Leclerc, Hélène; Ducrocq, Vincent

2017-10-01

Claw lesions are one of the most important health issues in dairy cattle. Although the frequency of claw lesions depends greatly on herd management, the frequency can be lowered through genetic selection. A genetic evaluation could be developed based on trimming records collected by claw trimmers; however, not all cows present in a herd are usually selected by the breeder to be trimmed. The objectives of this study were to investigate the importance of the preselection of cows for trimming, to account for this preselection, and to estimate genetic parameters of claw health traits. The final data set contained 25,511 trimming records of French Holstein cows. Analyzed claw lesion traits were digital dermatitis, heel horn erosion, interdigital hyperplasia, sole hemorrhage circumscribed, sole hemorrhage diffused, sole ulcer, and white line fissure. All traits were analyzed as binary traits in a multitrait linear animal model. Three scenarios were considered: including only trimmed cows in a 7-trait model (scenario 1); or trimmed cows and contemporary cows not trimmed but present at the time of a visit (considering that nontrimmed cows were healthy) in a 7-trait model (scenario 2); or trimmed cows and contemporary cows not trimmed but present at the time of a visit (considering lesion records for trimmed cows only), in an 8-trait model, including a 0/1 trimming status trait (scenario 3). For scenario 3, heritability estimates ranged from 0.02 to 0.09 on the observed scale. Genetic correlations clearly revealed 2 groups of traits (digital dermatitis, heel horn erosion, and interdigital hyperplasia on the one hand, and sole hemorrhage circumscribed, sole hemorrhage diffused, sole ulcer, and white line fissure on the other hand). Heritabilities on the underlying scale did not vary much depending on the scenario: the effect of the preselection of cows for trimming on the estimation of heritabilities appeared to be negligible. However, including untrimmed cows as healthy caused bias in the estimation of genetic correlations. The use of a trimming status trait to account for preselection appears promising, as it allows consideration of the exhaustive population of cows present at the time a trimmer visited a farm without causing bias in genetic parameters. Copyright © 2017 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Accommodation of practical constraints by a linear programming jet select. [for Space Shuttle

NASA Technical Reports Server (NTRS)

Bergmann, E.; Weiler, P.

1983-01-01

An experimental spacecraft control system will be incorporated into the Space Shuttle flight software and exercised during a forthcoming mission to evaluate its performance and handling qualities. The control system incorporates a 'phase space' control law to generate rate change requests and a linear programming jet select to compute jet firings. Posed as a linear programming problem, jet selection must represent the rate change request as a linear combination of jet acceleration vectors where the coefficients are the jet firing times, while minimizing the fuel expended in satisfying that request. This problem is solved in real time using a revised Simplex algorithm. In order to implement the jet selection algorithm in the Shuttle flight control computer, it was modified to accommodate certain practical features of the Shuttle such as limited computer throughput, lengthy firing times, and a large number of control jets. To the authors' knowledge, this is the first such application of linear programming. It was made possible by careful consideration of the jet selection problem in terms of the properties of linear programming and the Simplex algorithm. These modifications to the jet select algorithm may by useful for the design of reaction controlled spacecraft.

Precision of 655nm Confocal Laser Profilometry for 3D surface texture characterisation of natural human enamel undergoing dietary acid mediated erosive wear.

PubMed

Mullan, F; Mylonas, P; Parkinson, C; Bartlett, D; Austin, R S

2018-03-01

To assess the precision of optical profilometry for characterising the 3D surface roughness of natural and polished human enamel in order to reliably quantify acid mediated surface roughness changes in human enamel. Forty-two enamel samples were prepared from extracted human molars and either polished flat or left unmodified. To investigate precision, the variability of thirty repeated measurements of five areas of one polished and one natural enamel sample was assessed using 655nm Confocal Laser Profilometry. Remaining samples were subjected to forty-five minutes orange juice erosion and microstructural changes were analysed using Sa roughness change (μm) and qualitatively using surface/subsurface confocal microscopy. Enamel surface profilometry from the selected areas revealed maximal precision of 5nm for polished enamel and 23nm for natural enamel. After erosion, the polished enamel revealed a 48% increase in mean (SD) Sa roughness of 0.10 (0.07)μm (P<0.05), whereas in contrast the natural enamel revealed a 45% decrease in mean (SD) roughness of -0.32 (0.42)μm (P<0.05). These data were supported by qualitative confocal images of the surface/subsurface enamel. This study demonstrates a method for precise surface texture measurement of natural human enamel. Measurement precision was superior for polished flat enamel in contrast to natural enamel however, natural enamel responds very differently to polished enamel when exposed to erosion challenges. Therefore, thus future studies characterising enamel surface changes following erosion on natural enamel may provide more clinically relevant responses in comparison to polished enamel. Copyright © 2017 The Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Critical Source Area Delineation: The representation of hydrology in effective erosion modeling.

NASA Astrophysics Data System (ADS)

Fowler, A.; Boll, J.; Brooks, E. S.; Boylan, R. D.

2017-12-01

Despite decades of conservation and millions of conservation dollars, nonpoint source sediment loading associated with agricultural disturbance continues to be a significant problem in many parts of the world. Local and national conservation organizations are interested in targeting critical source areas for control strategy implementation. Currently, conservation practices are selected and located based on the Revised Universal Soil Loss Equation (RUSLE) hillslope erosion modeling, and the National Resource Conservation Service will soon be transiting to the Watershed Erosion Predict Project (WEPP) model for the same purpose. We present an assessment of critical source areas targeted with RUSLE, WEPP and a regionally validated hydrology model, the Soil Moisture Routing (SMR) model, to compare the location of critical areas for sediment loading and the effectiveness of control strategies. The three models are compared for the Palouse dryland cropping region of the inland northwest, with un-calibrated analyses of the Kamiache watershed using publicly available soils, land-use and long-term simulated climate data. Critical source areas were mapped and the side-by-side comparison exposes the differences in the location and timing of runoff and erosion predictions. RUSLE results appear most sensitive to slope driving processes associated with infiltration excess. SMR captured saturation excess driven runoff events located at the toe slope position, while WEPP was able to capture both infiltration excess and saturation excess processes depending on soil type and management. A methodology is presented for down-scaling basin level screening to the hillslope management scale for local control strategies. Information on the location of runoff and erosion, driven by the runoff mechanism, is critical for effective treatment and conservation.

Erosion and Gully formation in the Ethiopian Highlands: physical observations and community perspectives

NASA Astrophysics Data System (ADS)

Guzman, C. D.; Admassu, S.; Derebe, A.; Yitaferu, B.; Steenhuis, T. S.

2013-12-01

The aims of this investigation are to analyze spatio-temporal variations in sediment transport to waterways in a small agricultural watershed by: (i) locating sediment sources using modeling and bio-physical scientific approaches, (ii) locating sediment sources and erosion processes through age- and gender-differentiated focus group discussions and transect walks, and (iii) linking sediment sources to changes in soil nutrient concentrations. The collected field measurements, modeling results, and community perceptions have been gathered on an area encompassing a previous study site (14 ha) on a currently larger scale (95 ha) in the Debre Mewi watershed to develop a fuller picture of the social and environmental conditions that are leading to induced or controlled erosion and gully formation. Farmers provided their perspectives on erosion processes and these were complemented by and compared to soil and water field measurements during the rainy season. Sixteen sites were selected for monitoring and measuring groundwater, soil nutrient changes, and soil depth change on the 95 ha study area, based on land use and slope angle -- half represent grazing or fallow land and half are located on cultivated land. A set of stable gullies and actively forming gullies were monitored and measured simultaneously along hillslope locations in the top, middle and bottom areas. In addition, sediment concentration samples were collected at 4 weir locations in the 95 ha watershed and also at the final outlet to this watershed. Modeling efforts emphasize steep cropland as most vulnerable, whereas community members pointed out waterlogged black soils and lower areas as vulnerable. The data demonstrate that saturated pathways in the landscape provide areas for the development and widening of gullies and that flat cropland areas experience deposition rather than erosion, while soil nutrient concentrations are decreasing upslope and increasing downslope.

Erosion and Gully Formation in the Ethiopian Highlands: Physical Observations and Community Perspectives

NASA Astrophysics Data System (ADS)

Guzman, Christian; Dagnew, Dessalegn; Zegeye, Assefa; Tilahun, Seifu; Yitaferu, Birru; Stoof, Cathelijne; Steenhuis, Tammo

2014-05-01

The aims of this investigation are to analyze spatio-temporal variations in sediment transport to waterways in a small agricultural watershed by: (i) locating sediment sources using modeling and bio-physical scientific approaches, (ii) locating sediment sources and erosion processes through age- and gender-differentiated focus group discussions and transect walks, and (iii) linking sediment sources to changes in soil nutrient concentrations. The collected field measurements, modeling results, and community perceptions have been gathered on an area encompassing a previous study site (14 ha) on a currently larger scale (95 ha) in the Debre Mewi watershed to develop a fuller picture of the social and environmental conditions that are leading to induced or controlled erosion and gully formation. Farmers provided their perspectives on erosion processes and these were complemented by and compared to soil and water field measurements during the rainy season. Nine sites were selected for monitoring and measuring groundwater, soil nutrient changes, and soil depth change on the 95 ha study area, based on land use and slope angle -- half represent grazing or fallow land and half are located on cultivated land. A set of stable gullies and actively forming gullies were monitored and measured simultaneously along hillslope locations in the top, middle and bottom areas. In addition, sediment concentration samples were collected at 4 weir locations in the 95 ha watershed and also at the final outlet to this watershed. Modeling efforts emphasize steep cropland as most vulnerable, whereas community members pointed out waterlogged black soils and lower areas as vulnerable. The data demonstrate that saturated pathways in the landscape provide areas for the development and widening of gullies and that flat cropland areas experience deposition rather than erosion, while soil nutrient concentrations are decreasing upslope and increasing downslope.

Epidemiological studies of tooth wear and dental erosion in 14-year old children in North West England. Part 2: The association of diet and habits.

PubMed

Milosevic, A; Bardsley, P F; Taylor, S

2004-10-23

To determine the strength of association (expressed as Odds Ratios) of potential risk factors with erosion and tooth wear in 14-year-old schoolchildren. A random sample of 2,385 children were selected by a stratified two-stage technique based on schools and children. Schools in NW England. Tooth wear was assessed by one examiner on three surfaces of all 12 anterior teeth (labial, incisal and palatal) and the occlusal surface of all four first molars using a four-point scale. Enamel wear was scored 0, dentine exposure <1/3 scored 1, >1/3 scored 2 and secondary dentine or pulpal exposure, scored 3. A questionnaire enquired about general health, dental health, habits and the frequency of intake of a wide range of foods and drinks. The Odds Ratios for tooth wear on any surface for habits, reflux and certain foods were: bruxism, 1.10; stomach upset, 1.45; pickles 1.86; vinegar 1.36; salt and vinegar crisps 1.33; brown/other sauces 1.57. Similarly, the odds ratios for potentially erosive drinks were: fizzy drinks 1.32; sport drinks 1.58; herbal/lemon tea 3.97. The frequency of intake was bi-modal with 397 children drinking a can per day and 207 drinking two cans per day. A significant number drank acidic beverages at bedtime but this was not associated with dental erosion. Although odds ratios greater than unity indicate an association, this was not high for carbonated beverages and many other acidic foods or drinks. Examining at fourteen years may not be ideal, as the determinants of erosion/tooth wear have not acted for long, the indices do not discriminate sufficiently and proportionately few subjects have dentine exposed on smooth surfaces.

A comparison among root soil-conservation effects for nine herbs at the cold region highway in north-eastern China

NASA Astrophysics Data System (ADS)

Xu, W.; Wang, X.; Zhang, Y.; Liu, Y.

2014-12-01

High soil-conservation herbs are very important for slope vegetation restoration of a highway in serious sandstorm regions. In this study, nine common herbs in northeast China were selected and compared to study soil-conservation effects by using an undisturbed-soil trough scouring method for soil anti-scourability enhancement and hydrostatic collapse method for soil anti-erodibility. Further, principal components analysis was used to identify significant root features that affected soil erosion resistance. Results indicated that different herbs had distinct enhancement effects on soil erosion resistance. Soil anti-scourability enhancement index decreased with increases of soil depth, slope gradient and rainfall amount. Relationship between soil anti-erodibility enhancement index ( S) and immersion time ( t) is a cubic spline in each different herb type ( R 2 ≥ 0.88). Herb root features such as micro-aggregates, organic matter, net leaf weight, thick root length, fine root length and biomass contributed a leading role in soil erosion resistance enhancement effect, and all their common factor variances were more than 0.81. Descending order of soil erosion resistance enhancement effect in soil anti-scourability for nine herbs is Poa pratensis, Medicago sativa, Viola philippica, Rudbeckia hirta, Clematis heracleifolia, Kalimeris indica, Cosmos bipinnata, Hemerocallis fulva and Sedum elatinoides, while the sequence of soil anti-erodibility is M. sativa, S. elatinoides, P. pratensis, R. hirta, H. fulva, V. philippica, C. heracleifolia, C. bipinnata and K. indica. Therefore, we concluded that P. pratensis and M. sativa were the most suitable herbs for resisting soil erosion and recommended to be widely planted for road vegetation recovery in this region.

Combining Field and Laboratory Experiments in Order to Understand Interactions Between Flow, Sediment, Vegetation And Bank Erosion in Riparian Rehabilitation Works

NASA Astrophysics Data System (ADS)

Rodriguez, J. F.; Gorrick, S.; Kalma, J.; Cook, N.; Outhet, D.; Raine, A.

2005-12-01

Riparian lands are important for maintaining viable ecosystems, improving water quality and reducing sediment yields. Yet, riparian lands are frequently neglected, degraded and poorly managed. In many Australian riverine zones clearing or grazing of native riparian vegetation has resulted in varying degrees of erosion, sedimentation and degradation of aquatic ecosystems. Reintroducing riparian vegetation is one of the preferred methods for improving bank stability, reducing bank erosion to natural rates and rehabilitating channels. The present research aims to explore how reintroduced riparian vegetation modifies the flow and sediment transport patterns and at the same time how the vegetation is affected by flow and sediment. Both field experimentation and laboratory studies will lead to basic understanding of the processes involved and will help the efficient design of plantings for riparian rehabilitation. In order to be able to reproduce the most important processes in a laboratory physical model, a field site with a relatively simple geometry has been selected for the study. The site is on a small sand bed stream in the Hunter Valley in NSW. The reach has a large radius bend with no riparian vegetation on the outer bank, where erosion occurs periodically. Reintroduction of vegetation is planned for October 2005, with pre and post monitoring stages running from March 2005 to August 2008. Laboratory physical modelling based on field characteristics and with varying flow discharges and plant arrangement will provide information to help develop, adapt and test quantitative models of flow dynamics, sediment transport and bank erosion incorporating the effects of vegetation. These results can then be used by river managers when they are developing rehabilitation strategies.

Relative influence of wildfire on soil properties and erosion processes in different Mediterranean environments in NE Spain.

PubMed

Pardini, Giovanni; Gispert, Maria; Dunjó, Gemma

2004-07-26

Abandonment of terraced soils and increased brushland cover has increased wildfire occurrence to almost an annual rate in the Cap de Creus Peninsula, NE Pyrenees Range, Province of Girona, Spain. A wildfire occurred in August 2000 and affected an area of 6760 ha of shrubs and cork trees, whereas still cultivated plots were only slightly affected. Five stations of erosion measurements, corresponding to five different environments (from present cultivation to late abandonment) were destroyed by the passage of fire, and were promptly replaced to allow to monitoring post-fire effects on soil erosion. Selected soil properties were determined monthly before the fire and during 6 months after the fire at a monthly rate. Runoff and sediment yield together with dissolved organic carbon (DOC) in runoff water and organic carbon losses in eroded sediments (EOC) were evaluated throughout 2000. The last stage of abandonment, stands of cork trees, had the highest soil stability. Nevertheless, evidence of unfavourable soil conditions was detected at the shrub stage, when Cistus monspeliensis cover was the dominant opportunistic plant. This stage was considered to be a critical threshold leading either to degradation or regeneration processes according to fire frequency. A drastic change in soil properties, erosion and nutrient depletion occurred after the fire in all the environments. Statistics enabled to state that environments differed significantly in main soil properties. By statistically comparing the measured variables between the environments before and after the fire, DOC was found to be the soil parameter showing the highest significance between environments. Absolute values of erosion were low with respect to other Mediterranean environments although the shallow nature of these soils might deserve special attention because of a comparatively higher risk of degradation. Copyright 2004 Elsevier B.V.

Clinical experience with pantoprazole in gastroesophageal reflux disease.

PubMed

Avner, D L

2000-10-01

Pantoprazole is a new proton pump inhibitor indicated for the treatment of erosive esophagitis associated with gastroesophageal reflux disease (GERD) and is available in both oral and intravenous (IV) formulations. This paper reviews the pharmacologic properties of pantoprazole and summarizes the findings from clinical studies of this drug. This review was compiled from the published literature, abstracts from clinical trials, and data on file with the manufacturer of pantoprazole. Pantoprazole selectively accumulates in the acidic environment of gastric parietal cells and acts at the final step of acid secretion by binding 2 key cysteine residues of the proton pump involved in gastric acid production. The bioavailability of pantoprazole is not altered by concomitant administration of food or antacids or with repeated dosing. Both oral and IV formulations of pantoprazole exhibit linear pharmacokinetics. Several clinical trials have proved pantoprazole superior to histamine-2-receptor antagonists (H2RAs) in reducing acid secretion and elevating gastric pH levels. Pantoprazole has been shown to be more effective than ranitidine (P < 0.05), famotidine (P < 0.001), and nizatidine (P < 0.05), and at least as effective as omeprazole, in healing erosive esophagitis and relieving associated symptoms of GERD, including regurgitation. Pantoprazole is also more effective than the H2RA nizatidine for the treatment of nighttime heartburn (P < 0.05). Studies have shown pantoprazole to be well tolerated; adverse events, including headache, diarrhea, flatulence, abdominal pain, eructation, nausea, and rash, occurred in < or = 6% of patients. The oral and IV formulations of pantoprazole are equally potent in inhibiting gastric acid secretion; thus, switching between formulations requires no dosage adjustments. Special patient populations, including the elderly and patients with renal or mild to moderate hepatic impairment, can take pantoprazole without an adjustment in dosage. Because of its unique pharmacokinetic properties, mechanism of action, and reduced potential for producing cytochrome P-450-based drug interactions, pantoprazole in both oral and IV formulations is effective over a full 24 hours and is well tolerated in a variety of patient types.

Interpolation Approaches for Characterizing Spatial Variability of Soil Properties in Tuz Lake Basin of Turkey

NASA Astrophysics Data System (ADS)

Gorji, Taha; Sertel, Elif; Tanik, Aysegul

2017-12-01

Soil management is an essential concern in protecting soil properties, in enhancing appropriate soil quality for plant growth and agricultural productivity, and in preventing soil erosion. Soil scientists and decision makers require accurate and well-distributed spatially continuous soil data across a region for risk assessment and for effectively monitoring and managing soils. Recently, spatial interpolation approaches have been utilized in various disciplines including soil sciences for analysing, predicting and mapping distribution and surface modelling of environmental factors such as soil properties. The study area selected in this research is Tuz Lake Basin in Turkey bearing ecological and economic importance. Fertile soil plays a significant role in agricultural activities, which is one of the main industries having great impact on economy of the region. Loss of trees and bushes due to intense agricultural activities in some parts of the basin lead to soil erosion. Besides, soil salinization due to both human-induced activities and natural factors has exacerbated its condition regarding agricultural land development. This study aims to compare capability of Local Polynomial Interpolation (LPI) and Radial Basis Functions (RBF) as two interpolation methods for mapping spatial pattern of soil properties including organic matter, phosphorus, lime and boron. Both LPI and RBF methods demonstrated promising results for predicting lime, organic matter, phosphorous and boron. Soil samples collected in the field were used for interpolation analysis in which approximately 80% of data was used for interpolation modelling whereas the remaining for validation of the predicted results. Relationship between validation points and their corresponding estimated values in the same location is examined by conducting linear regression analysis. Eight prediction maps generated from two different interpolation methods for soil organic matter, phosphorus, lime and boron parameters were examined based on R2 and RMSE values. The outcomes indicate that RBF performance in predicting lime, organic matter and boron put forth better results than LPI. However, LPI shows better results for predicting phosphorus.

The Status of Agroforestry in the South

Treesearch

F. Christian Zinkhan; D. Evan.  Mercer

1997-01-01

Southern agroforestty has emerged as a significant research topic. Research results indicate that agroforestty can address such sustainability problems as erosion and water pollution, while improving economic performance in selected situatiOII& Silvopastoral systems are the most commonly adopted agroforestty application in the region; le!6-common alley-cropping...

Resesrvoir sedimentation rates in the Little Washita River experimental watershed, Oklahoma

USDA-ARS?s Scientific Manuscript database

The Washita River Basin (WRB) was one of eleven pilot watershed projects selected for construction of flood control reservoirs around the country as a result of the Flood Control Act of 1936. These reservoirs were implemented to prevent and manage soil erosion and flooding. A total of 45 reservoirs ...

44 CFR 59.23 - Priorities for the sale of flood insurance under the regular program.

Code of Federal Regulations, 2010 CFR

2010-10-01

...-related erosion prone communities are placed on a register of areas eligible for ratemaking studies and then selected from this register for ratemaking studies on the basis of the following considerations— (a) Recommendations of State officials; (b) Location of community and urgency of need for flood...

44 CFR 59.23 - Priorities for the sale of flood insurance under the regular program.

Code of Federal Regulations, 2011 CFR

2011-10-01

...-related erosion prone communities are placed on a register of areas eligible for ratemaking studies and then selected from this register for ratemaking studies on the basis of the following considerations— (a) Recommendations of State officials; (b) Location of community and urgency of need for flood...

Gotel Mountains, Nigeria and Cameroon, SRTM Shaded Relief plus Height as Brightness

NASA Technical Reports Server (NTRS)

2004-01-01

River drainage patterns provide clues to the rock types and erosional processes involved in landscape evolution. Here in the Gotel Mountains along the border between Nigeria and Cameroon two distinct and highly contrasting patterns are evident. The lowlands in the northern and northwestern parts of the scene exhibit 'dendritic' patterns, while the highlands in the southern and southeastern parts of the scene show 'rectangular' and other linear drainage patterns.

Dendritic drainage patterns appear almost random. Moving upstream, streams split into smaller and smaller channels, with finer and finer spacing, and they show little preference for map orientation other than to complete the pattern. In contrast, rectangular and other linear drainage patterns show a distinct preference for certain orientations in map view. In this scene, the two major preferred orientations are rotated slightly clockwise of north-south and east-west.

Linear drainage patterns usually match the cracking patterns that can occur in relatively hard rocks, including igneous rocks such as granite and basalt. Stream erosion typically follows such lines of weakness in these hard rocks. Meanwhile, the randomness of dendritic patterns indicates that no such cracks nor any other geologic structure controls the erosion where that pattern occurs.

Given the above, the topographic pattern in this scene appears to tell us the following about the geology of this location. The lowlands are composed of poorly consolidated (relatively soft) rocks or sediments that are at least 100 meters (330 feet) thick and are 'massive' (uniform, with no prominent layering at the observed scale). The randomness of the dendritic patterns further indicates that stream erosion is the only significant dynamic process altering the lowland landscape. Forces such as volcanism and tectonics are not altering these landforms.

Meanwhile, the neighboring highlands are composed of crystalline rocks, such as granite, that are very hard (generally resistant to erosion) and probably very old. Sometime through their history these rocks cracked, perhaps when they cooled, perhaps under tectonic stress, or perhaps when pressure upon them was relieved when they were unearthed by erosion. Now at the surface, these cracks are zones of weakness as these hard rocks otherwise resist stream erosion.

But while the topographic data gives clues, it does not always provide definitive answers. Are the lowlands made up of soft sediments washed in from elsewhere or are they simply rocks 'softened' by weathering (disintegration into sand) in place over time. If the latter, might they in fact have been granite also? The two patterns interfinger geographically, suggesting that the rugged highlands may be evolving into the dendritic lowlands. Weathering products (loose sands) tend to accumulate in place in low relief terrain because erosion there is slow to remove them. Also, granites are typically 'massive' and cracking patterns vanish when the rocks disintegrate. The topographic data indeed provide thought provoking evidence, but definitive answers will require fieldwork or other additional evidence.

This image was created directly from an SRTM elevation model. A shade image was derived by computing topographic slope in the north-south direction. Northern slopes appear bright and southern slopes appear dark. The shade image was then merged with a height-as-brightness image, which helps clarify the continuity of the drainage networks.

Elevation data used in this image was acquired by the Shuttle Radar Topography Mission (SRTM) aboard the Space Shuttle Endeavour, launched on February 11, 2000. SRTM used the same radar instrument that comprised the Spaceborne Imaging Radar-C/X-Band Synthetic Aperture Radar (SIR-C/X-SAR) that flew twice on the Space Shuttle Endeavour in 1994. SRTM was designed to collect three-dimensional measurements of the Earth's surface. To collect the 3-D data, engineers added a 60-meter-long (200-foot) mast, installed additional C-band and X-band antennas, and improved tracking and navigation devices. The mission is a cooperative project between the National Aeronautics and Space Administration (NASA), the National Geospatial-Intelligence Agency (NGA) of the U.S. Department of Defense (DoD), and the German and Italian space agencies. It is managed by NASA's Jet Propulsion Laboratory, Pasadena, Calif., for NASA's Earth Science Enterprise, Washington, D.C.

Size: 144.8 kilometers (89.8 miles) by 131.5 kilometers (81.5 miles) Location: 7 degrees North latitude, 10 degrees East longitude Orientation: North toward the top Image Data: SRTM elevation shaded plus height-as-brightness Date Acquired: February 2000

Accurate, low-cost 3D-models of gullies

NASA Astrophysics Data System (ADS)

Onnen, Nils; Gronz, Oliver; Ries, Johannes B.; Brings, Christine

2015-04-01

Soil erosion is a widespread problem in arid and semi-arid areas. The most severe form is the gully erosion. They often cut into agricultural farmland and can make a certain area completely unproductive. To understand the development and processes inside and around gullies, we calculated detailed 3D-models of gullies in the Souss Valley in South Morocco. Near Taroudant, we had four study areas with five gullies different in size, volume and activity. By using a Canon HF G30 Camcorder, we made varying series of Full HD videos with 25fps. Afterwards, we used the method Structure from Motion (SfM) to create the models. To generate accurate models maintaining feasible runtimes, it is necessary to select around 1500-1700 images from the video, while the overlap of neighboring images should be at least 80%. In addition, it is very important to avoid selecting photos that are blurry or out of focus. Nearby pixels of a blurry image tend to have similar color values. That is why we used a MATLAB script to compare the derivatives of the images. The higher the sum of the derivative, the sharper an image of similar objects. MATLAB subdivides the video into image intervals. From each interval, the image with the highest sum is selected. E.g.: 20min. video at 25fps equals 30.000 single images. The program now inspects the first 20 images, saves the sharpest and moves on to the next 20 images etc. Using this algorithm, we selected 1500 images for our modeling. With VisualSFM, we calculated features and the matches between all images and produced a point cloud. Then, MeshLab has been used to build a surface out of it using the Poisson surface reconstruction approach. Afterwards we are able to calculate the size and the volume of the gullies. It is also possible to determine soil erosion rates, if we compare the data with old recordings. The final step would be the combination of the terrestrial data with the data from our aerial photography. So far, the method works well and we are able to produce accurate and low-cost 3D-models of gullies.

Geomorphic consequences of rapid deglaciation at Pasterze Glacier, Hohe Tauern Range, Austria, between 2010 and 2013 based on repeated terrestrial laser scanning data

NASA Astrophysics Data System (ADS)

Avian, M.; Kellerer-Pirklbauer, A.; Lieb, G. K.

2018-06-01

Since the end of the Little Ice Age around 1850 CE glaciers in the Alps have been receding dramatically. This study aimed to quantify and characterize the geomorphic and landform changes of a 0.9 km2 large proglacial area at the largest glacier in Austria (Pasterze Glacier, Austria, N 47°04‧, E 12°44‧). Point clouds from multiple terrestrial laserscanning (TLS) and different image data were used to quantify surface elevation changes and distinguish different types of erosional and depositional landforms during the period 2010-2013. Results indicate that the study area is characterized by a total volume loss of 1,309,000 m3. Excluding the area which was deglaciated, the volume loss equals 275,000 m3 in the period 2010-13. The decrease is related to sediment transfer out of study area and due to sediment-buried glacier ice which is slowly melting. The landform classification reveals that drift mantled slopes are most frequent (20.9% of the study area in 2013) next to ice contact terrace landforms (19.7%). In terms of vertical surface elevation changes, our results suggest distinguishing between 3 distinct domains within the study area: (i) a flat valley bottom area consisting of water/sandur areas and ice-cored landforms dominated by widespread subsurface ice melting and lateral fluvial (and thermal) erosion; (ii) a gently-sloping footslope area consisting of ice-contact sediments, former ice marginal channels and deep incised gullies with corresponding debris cones dominated by linear erosion and corresponding deposition; and (iii) a steep lateral slope area mainly built up of consolidated drift material with incised gullies dominated by linear erosion. Our results not only confirm the previously revealed high geomorphic activity for proglacial areas of alpine glaciers in terms of surface elevation variations, they also highlight that landforms might change substantially from one year to the next not only because of erosional/depositional processes, but also because of the melting of buried dead-ice bodies.

Towards a Multi-scale Montecarlo Climate Emulator for Coastal Flooding and Long-Term Coastal Change Modeling: The Beautiful Problem

NASA Astrophysics Data System (ADS)

Rueda, A.; Alvarez Antolinez, J. A.; Hegermiller, C.; Serafin, K.; Anderson, D. L.; Ruggiero, P.; Barnard, P.; Erikson, L. H.; Vitousek, S.; Camus, P.; Tomas, A.; Gonzalez, M.; Mendez, F. J.

2016-02-01

Long-term coastal evolution and coastal flooding hazards are the result of the non-linear interaction of multiple oceanographic, hydrological, geological and meteorological forcings (e.g., astronomical tide, monthly mean sea level, large-scale storm surge, dynamic wave set-up, shoreline evolution, backshore erosion). Additionally, interannual variability and trends in storminess and sea level rise are climate drivers that must be considered. Moreover, the chronology of the hydraulic boundary conditions plays an important role since a collection of consecutive minor storm events can have more impact than the 100-yr return level event. Therefore, proper modeling of shoreline erosion, beach recovery and coastal flooding should consider the sequence of storms, the multivariate nature of the hydrodynamic forcings, and the different time scales of interest (seasonality, interannual and decadal variability). To address this `beautiful problem', we propose a hybrid approach that combines: (a) numerical hydrodynamic and morphodynamic models (SWAN for wave transformation, a shoreline change model, X-Beach for modeling infragravity waves and erosion of the backshore during extreme events and RFSM-EDA (Jamieson et al, 2012) for high resolution flooding of the coastal hinterland); (b) long-term data bases (observational and hindcast) of sea state parameters, astronomical tides and non-tidal residuals; and (c) statistical downscaling techniques, non-linear data mining, and extreme value models. The statistical downscaling approaches for multivariate variables are based on circulation patterns (Espejo et al., 2014), the chronology of the circulation patterns (Guanche et al, 2013) and the event hydrographs of multivariate extremes, resulting in a time-dependent climate emulator of hydraulic boundary conditions for coupled simulations of the coastal change and flooding models. ReferencesEspejo et al (2014) Spectral ocean wave climate variability based on circulation patterns, J Phys Oc, doi: 10.1175/JPO-D-13-0276.1 Guanche et al (2013) Autoregressive logistic regression applied to atmospheric circulation patterns, Clim Dyn, doi: 10.1007/s00382-013-1690-3 Jamieson et al (2012) A highly efficient 2D flood model with sub-element topography, Proc. Of the Inst Civil Eng., 165(10), 581-595

Export Time of Earthquake-Derived Landslides in Active Mountain Ranges

NASA Astrophysics Data System (ADS)

Croissant, T.; Lague, D.; Steer, P.; Davy, P.

2016-12-01

In active mountain ranges, large earthquakes (Mw > 5-6) trigger numerous landslides that impact river dynamics. These landslides bring local and sudden sediment deposits which are eroded and transported along the river network, causing downstream changes in river geometry, transport capacity and erosion efficiency. The progressive removal of landslide materials has implications for downstream hazards management and for landscape dynamics at the timescale of the seismic cycle. Although the export time of suspended sediments from landslides triggered by large-magnitude earthquakes has been extensively studied, the processes and time scales associated to bedload transport remains poorly studied. Here, we study the sediment export of large landslides with the 2D morphodynamic model, Eros. This model combines: (i) an hydrodynamic model, (ii) a sediment transport and deposition model and (iii) a lateral erosion model. Eros is particularly well suited for this issue as it accounts for the complex retro-actions between sediment transport and fluvial geometry for rivers submitted to external forcings such as abrupt sediment supply increase. Using a simplified synthetic topography we systematically study the influence of pulse volume (Vs) and channel transport capacity (QT) on the export time of landslides. The range of simulated river behavior includes landslide vertical incision, its subsequent removal by lateral erosion and the river morphology modifications induced by downstream sediment propagation. The morphodynamic adaptation of the river increases its transport capacity along the channel and tends to accelerate the landslide evacuation. Our results highlight two regimes: (i) the export time is linearly related to Vs/QT when the sediment pulse introduced in the river does not affect significantly the river hydrodynamic (low Vs/QT) and (ii) the export time is a non-linear function of Vs/QT when the pulse undergoes significant morphodynamic modifications during its evacuation (high Vs/QT). By combining our newly derived export time functions with the frequency-magnitude of earthquake intensity and the induced sediment production, we investigate the sediment export of several plausible earthquake scenarii in different mountain ranges (New Zealand, Taiwan, Nepal).

Medusae Fossae Formation

NASA Technical Reports Server (NTRS)

2002-01-01

(Released 16 April 2002) The Science This THEMIS visible image was acquired near 11o N, 159o W (201o E) and shows examples of the remarkable variations that can be seen in the erosion of the Medusae Fossae Formation. This Formation is a soft, easily eroded deposit that extends for nearly 1,000 km along the equator of Mars. In this region, like many others throughout the Medusae Fossae Formation, the surface has been eroded by the wind into a series of linear ridges called yardangs. These ridges generally point in direction of the prevailing winds that carved them, and demonstrate the power of martian winds to erode the landscape of Mars. The easily eroded nature of the Medusae Fossae Formation suggests that it is composed of weakly cemented particles, and was most likely formed by the deposition of wind-blown dust or volcanic ash. Within this single image it is possible to see differing amounts of erosion and stripping of layers in the Medusae Fossae Formation. Near the bottom (southern) edge of the image a rock layer with a relatively smooth upper surface covers much of the image. Moving upwards (north) in the image this layer becomes more and more eroded. At first there are isolated regions where the smooth unit has been eroded to produce sets of parallel ridges and knobs. Further north these linear knobs increase in number, and only small, isolated patches of the smooth upper surface remain. Finally, at the top of the image, even the ridges have been removed, exposing the remarkably smooth top of hard, resistant layer below. This sequence of layers with differing hardness and resistance to erosion is common on Earth and on Mars, and suggests significant variations in the physical properties, composition, particle size, and/or cementation of these martian layers. As is common throughout the Medusae Fossae Formation, very few impact craters are visible, indicating that the surface exposed is relatively young, and that the process of erosion may be active today. The Story 'Yardang!' Now, that may seem like a peculiar-sounding curse word, but nobody would get in trouble for using it. A yardang is one of the very cool-sounding words geologists use to describe long, irregular features like the ones seen in this image. Yardangs are grooved, furrowed ridges that form as the wind erodes away weakly cemented material in the region. Rippling across the surface, yardangs tell the story of how the powerful Martian wind carved the surface into such a gorgeous pattern over time. (Don't miss clicking on the above image to see a detailed view, in which the beauty and almost dance-like symmetry of the waving terrain pops out in highly compelling, three-dimensional texture.) It may be easy to see which way the wind blows in this area, since these streamlined features point in the direction of prevailing winds. But how can geologists understand the various kinds of terrain seen here? First, they have to study the different patterns of erosion, looking closely at how the wind has stripped off certain layers and not others. Want to be a geologist yourself? Start at the bottom of the image and scroll upward, and see how the relatively smooth, higher terrain toward the south gradually becomes more and more eroded. Moving up the image, at first you?ll see only a few, isolated regions of parallel ridges and knolls. Go a little farther north with your eyes (toward the center of the image), and you?ll see how these linear knobs really get going! Once you get to the top of the image, only patches of these grooved ridges remain, leaving an incredibly smooth, wind-scrubbed surface behind. You know this layer has to be made of pretty hard material, because it seems impervious to further erosion. Geologists studying Mars can compare these Martian yardangs to examples found on Earth, such as those in the Lut desert of Iran. Humans have even been known to use the wind as their inspiration, sculpting the shape of yardangs themselves. The famous sphynx at Giza in Egypt is thought to be a yardang that's been whittled down a little more by ancient human chiselers.

Modelling the Holderness coast, eastern England: Past, present and future

NASA Astrophysics Data System (ADS)

Barkwith, A.; Limber, P. W.; Thomas, C. W.; Murray, A.; Jordan, H. M.; Ellis, M. A.

2012-12-01

The Holderness coast of eastern Yorkshire, England, is the most rapidly eroding coastline in Europe. Erosion can locally exceed 10 m in a single year and rates average 0.5 to 3 m yr-1, generally increasing from north to south. Pinned in the north by a chalk headland, the soft till coastline has a characteristic open spiral form terminated by a spit to the south. Erosion currently threatens local communities and infrastructure, including nationally important gas installations. Interventions to restrict local erosion usually result in enhanced erosion in adjacent, unprotected sections of coast, mirroring morphology seen on the large scale. We have initiated a modelling study to investigate the key controls on the form and evolution of this coastline, and its response to climate change, building on the Coastline Evolution Model (CEM) developed at Duke University, NC. We have adapted the CEM to permit an ensemble of simulations to be undertaken, based upon modified offshore wave climates, initial conditions and forcing factors. The CEM follows a standard 1d approach, where the cross-shore is collapsed into a single data point, allowing the planform shoreline shape and dynamics to be simulated. The model facilitates study of a coast with variable erosion rates, and enables simulation of coastline evolution when sediment is supplied from an eroding shoreface. Additionally, the CEM is adapted to use an observed two year, offshore wave climate data set as input. Initial work focussed on reconstruction of current coastline shape from an ensemble of hypothetical early Holocene shoreface positions and past wave climates. First order reconstruction of shoreline shape was achieved using several differing initial conditions and wave climates. For the majority of successful simulations, a steady state was noted for proceeding years, where erosion proceeds at an equal rate along the length of the coast south of the headland. Together with a sensitivity analysis, the derivation of the current coastline provided initial conditions for the second phase of the work: simulating the morphological response of the Holderness coastline to possible future changes in climate over the next century. An ensemble of future possible wave climate perturbations was generated from predictions of the likely response of the North Sea to future climate change over the next century, and applied linearly to the observed wave climate as each simulation progressed. The ensemble output was compared to a baseline simulation, run for a century under current wave climate, to assess the impact of predicted future climate on coastal erosion. Although this study does not currently take into account the changes in storm frequency, rises in sea level or the anthropogenic inputs that could influence the results, the initial output indicates erosional rates over the next century are likely to be retarded for the Holderness coastline under a changing climate.

Ca isotopes, chemical weathering, and geomorphic controls on long-term climate

NASA Astrophysics Data System (ADS)

Moore, J.; Jacobson, A. D.; Holmden, C. E.; Craw, D.

2009-12-01

Calcium isotope geochemistry (δ44Ca) offers a unique opportunity to directly quantify proportions of riverine Ca originating from silicate versus carbonate weathering, which is essential for understanding how geomorphic processes affecting landscape evolution, such as tectonic uplift and glaciation, influence the long-term cycling of atmospheric CO2. We measured the elemental and δ44Ca chemistry of river and rock samples from the New Zealand Southern Alps. In combination with our geochemical data, we used runoff and suspended sediment fluxes to elucidate relationships between chemical weathering, mechanical erosion, and long-term climate. The S. Alps have uniform bedrock chemistry but significant tectonic and climatic gradients. West of the main topographic divide, watersheds drain schist and experience high runoff, uplift, and erosion rates. East of the main divide, watersheds drain greywacke or schist and experience lower runoff, uplift, and erosion rates. Glaciated watersheds with high erosion rates are present throughout the mountain range. Both schist and greywacke contain up to 3% metamorphic and hydrothermal calcite. Waters exhibit two-component mixing between calcite and silicate end-members when plotted as δ44Ca versus Ca/Sr. Scatter about the mixing curve is generally smaller than the analytical uncertainty of the measurements and likely reflects variability of the end-member compositions rather than fractionation. We used the mixing relationships to calculate percentages of Ca from silicate weathering. Rivers draining greywacke average 27.6% of Ca from silicate weathering with glaciated and non-glaciated watersheds yielding 41.8 and 19.5%, respectively. Rivers draining schist average 9.8% with glaciated and non-glaciated watersheds yielding 17.7 and 3.9%, respectively. Although Ca fluxes are larger west of the main divide where erosion and runoff are higher, the percentage of Ca from silicate weathering is smaller. Hence, long-term atmospheric CO2 consumption rates do not increase linearly with mechanical erosion because erosion continuously exposes fresh calcite. For non-glacial watersheds, δ44Ca and traditional Ca/Na mixing models yield similar results. However, a substantial difference exists for glacial watersheds. We think δ44Ca is a more sensitive tracer as the difference likely reflects glacial communition, which facilitates rapid and non-stoichiometric release of Ca ions from freshly cleaved silicate surfaces.¶ This study demonstrates the utility of using δ44Ca to trace silicate versus carbonate sources of riverine Ca. Our findings support previous contentions that much of the riverine Ca flux emanating from active orogens originates from carbonate weathering, which is not a sink for atmospheric CO2 over geologic timescales. However, our findings also reveal that silicate weathering and atmospheric CO2 consumption rates in glaciated watersheds are higher than previously realized.

Tectonic significance of porosity and permeability regimes in the red beds formations of the South Georgia Rift Basin

NASA Astrophysics Data System (ADS)

Akintunde, Olusoga M.; Knapp, Camelia C.; Knapp, James H.

2014-09-01

A simple, new porosity/permeability-depth profile was developed from available laboratory measurements on Triassic sedimentary red beds (sandstone) from parts of the South Georgia Rift (SGR) basin in order to investigate the feasibility for long-term CO2 storage. The study locations were: Sumter, Berkeley, Dunbarton, Clubhouse Crossroad-3 (CC-3) and Norris Lightsey wells. As expected, both porosity and permeability show changes with depth at the regional scale that was much greater than at local scale. The significant changes in porosity and permeability with depth suggest a highly compacted, deformed basin, and potentially, a history of uplift and erosion. The permeability is generally low both at shallow (less than 1826 ft/556.56 m) and deeper depths (greater than 1826 ft/556.56 m). Both porosity and permeability follow the normal trend, decreasing linearly with depth for most parts of the study locations with the exception of the Norris Lightsey well. A petrophysical study on a suite of well logs penetrating the Norris Lightsey red beds at depths sampled by the core-derived laboratory measurements shows an abnormal shift (by 50%) in the acoustic travel time and/or in the sonic-derived P-wave velocity that indicates possible faulting or fracturing at depth. The departure of the Norris Lightsey's porosities and permeabilities from the normal compaction trend may be a consequence of the existence of a fault/fracture controlled abnormal pressure condition at depth. The linear and non-linear behaviors of the porosity/permeability distribution throughout the basin imply the composition of the SGR red beds, and by extension analog/similar Triassic-Jurassic formations within the Eastern North American Margin have been altered by compaction, uplift, erosion and possible faulting that have shaped the evolution of these Triassic formations following the major phase of rifting.

A simple bias correction in linear regression for quantitative trait association under two-tail extreme selection.

PubMed

Kwan, Johnny S H; Kung, Annie W C; Sham, Pak C

2011-09-01

Selective genotyping can increase power in quantitative trait association. One example of selective genotyping is two-tail extreme selection, but simple linear regression analysis gives a biased genetic effect estimate. Here, we present a simple correction for the bias.

Gully incision rates on the bedrock of a large dip-slope landslide revealed by multi-period LiDAR DEMs

NASA Astrophysics Data System (ADS)

Chan, Y. C.; Hsieh, Y. C.

2017-12-01

Recent advances in airborne laser scanning (ALS) technology have provided a great opportunity for characterizing surface erosion through developing improved methods in multi-period DEM differencing and geomorphometry. This study uses three periods of ALS digital elevation model (DEM) data to analyze the short-term erosional features of the Tsaoling landslide triggered by the 1999 Chi-Chi earthquake in Taiwan. Two methods for calculating the bedrock incision rate, the equal-interval cross section selection method and the continuous swath profiles selection method, were used in the study after nearly ten years of gully incision following the earthquake-triggered dip-slope landslide. Multi-temporal gully incision rates were obtained using the continuous swath profiles selection method, which is considered a practical and convenient approach in terrain change studies. After error estimation and comparison of the multi-period ALS DEMs, the terrain change in different periods can be directly calculated, reducing time-consuming fieldwork such as installation of erosion pins and measurement of topographic cross sections on site. In this study, the gully bedrock incision rates ranged between 0.23 and 3.98 m/year, remarkably higher than the typical results from the previous studies. By comparing the DEM data, aerial photos, and precipitation records of this area, the effects of erosion could be observed from the retreat of the Chunqiu Cliff outline during August 2011 to September 2012. It was inferred that the change in the topographic elevation during 2011-2012 was mainly due to the torrential rain brought by Typhoon Soula, which occurred on 30 July 2012. The local gully incision rate in the lower part of the landslide surface was remarkably faster than that of the other regions, suggesting that the fast incision of the toe area possibly contributes to the occurrence of repeated landslides in the Tsaoling area.

Using remote sensing for volumetric analyses of soil degradation by erosion

NASA Astrophysics Data System (ADS)

Vlacilova, Marketa; Krasa, Josef; Kavka, Petr

2014-05-01

Soil degradation by erosion can be effectively monitored or quantified by modern tools of remote sensing with variable level of detail accessible. The presented study deals with rill erosion assessment using stereoscopic images and orthophotos obtained by UAV (unmanned aerial vehicle). Advantages of UAVs are data in high resolution (1-10 cm/pixel), flexibility of data acquisition and price in comparison with standard aerial photography. Location attacked by intensive rainfall event in the spring 2013 was selected for this study of volumetric assessment of soil degradation by erosion. After the storm, rills and ephemeral gullies in different scales were detected on several fields in the target area. The study was focused on a single parcel catchment (12.5 ha) which attach to the main ephemeral gully in the monitored field. DEM of the location was obtained from UAV stereo images and official LIDAR data. At the same time, in-situ monitoring was effected for comparison and validation of methodology. The field measurement consisted of soil sampling and taking detailed stereo photographs of erosion rills. The photographs were processed by PhotoModeler Scanner software to obtain detailed surface data (TIN) of particular rills. The model for automatic and precise volumetric assessment of single rills was developed within ArcGIS. The whole study area DEM obtained from UAV was also analysed in ArcGIS using similar methodology for computation of rill volumes. The UAV DEM detected most rill bottoms and shapes however the level of detail was too low for actual sediment transport volume estimate. Therefore the volume obtained from UAV DEM was calibrated by the detailed models of single rills acquired by field measurement. Prior the calibration the UAV DEM volume was underestimated by 40-85% based on the rill size. Afterwards the target area was split into twelve separated regions defined by intensity and form of soil degradation (orthophoto-classified rill density). Equally, at least one representative square plot in each section was created. Next, the volume of erosion rills in each square plot was calculated and corrected by referenced relation. These results were extrapolated to the whole of the study catchment. The study contains volumetric evaluation of actual soil loss by rill erosion in detailed scale and in addition, there is a model for rill volume evaluation in highly detached fields. The results illustrate that the volume of soil loss can reach extreme values in detached areas after only one intensive rainfall event. Hundreds of cubic metres of soil can be transported in rills and ephemeral gullies from a single hectare of arable land. Findings are useful for development and verification of procedures for the identification and evaluation of actual degradation of agricultural land by water erosion. The research has been supported by the project No. QJ330118 "Using Remote Sensing for Monitoring of Soil Degradation by Erosion and Erosion Effects".

Risperidone mucoadhesive buccal tablets: formulation design, optimization and evaluation

PubMed Central

Çelik, Burak

2017-01-01

The aim of this study was to design and optimize risperidone (RIS) mucoadhesive buccal tablets for systemic delivery as an alternative route. Direct compression method was used for the preparation of buccal tablets, and screening studies were conducted with different polymers to determine their effects on tablet characteristics. Carbopol® (CP) and sodium alginate (SA) were selected as two polymer types for further optimization studies by applying response surface methodology. Tablet hardness (TH), ex vivo residence time (RT), and peak detachment force (DF) from buccal mucosa were selected as three important responses. Physicochemical compatibility of formulation excipients and RIS was evaluated by using Fourier transform infrared (FT-IR) spectroscopy and differential scanning calorimetry (DSC) analysis. In vitro drug release profiles and release kinetics were investigated; swelling index and matrix erosion studies were conducted. Optimum formulation consisted of 16.4% CP and 20.3% SA, which provided 7.67±0.29 hour ex vivo RT, 45.52±4.85 N TH, and 2.12±0.17 N DF. FT-IR spectroscopy and DSC analysis revealed that there was no chemical interaction present between tablet ingredients. Cumulative RIS release of >90% was achieved after 8 hours of in vitro dissolution studies, which was supported by swelling and matrix erosion analysis. Mechanism of RIS release was fitted best to zero-order model, while release exponent (n) value of 0.77 demonstrated an anomalous (non-Fickian) release, indicating combined erosion and swelling mechanism. The results suggested that optimized buccal tablets of RIS would be a promising and alternative delivery system for the treatment of schizophrenia. PMID:29225461

Long term characterization of ephemeral gully erosion from orthophotographs

NASA Astrophysics Data System (ADS)

Chahor, Youssef; Casalí, Javier; Giménez, Rafael; Ángel Campo-Bescós, Miguel

2017-04-01

For a knowledge of the importance and characteristics of ephemeral gully (EG) erosion to be adequate, continuous observations and measurements for long periods of time are required. Despite recent methodological advances, such as the availability of drones or photo-reconstruction, the data obtained from orthophotos taken on approximately the same dates for several years in the same places can supply information of great interest. This study aims to explore the applicability of orthophotos taken during 8 years to make a semi-detailed characterization of erosion due to ephemeral gullies over an extensive area. Thus, a homogeneous area as regards soil type, use and management, of around 570 hectares, was selected in the municipality of Pitillas, Navarra, frequently affected by EGs to carry out a long-term monitoring of it. From 8 orthophotos (≈1:5000) taken in 2003 (17 Apr-20 Sep), 2006 (28 May), 2008 (19 Jun), 2010 (5-21 Jun), 2011 (25 Sep), 2012 (23 Jun), 2013 (24 Jul) and 2014 (17 Aug), the position of small channels was digitized, identifying their ends downstream and upstream, georeferencing them, and determining their length. All the photos were taken in approximately the same season, usually in the summer. Since the area was cultivated with winter cereal or was lying fallow, its gullies have remained on the land since their formation, generally at the start of the winter, up to their elimination. This probably occurs due to tilling during the preparation tasks of the following sowing time, generally after the flight period. If we also consider that the EGs in the area remain almost unalterable after the winter, protected by the dense cereal vegetation, it can be affirmed that the flight dates supply adequate information on their final state. The authors' knowledge of the land simplified the identification of the gullies on the orthophotos. In the study area, 58 small watersheds were identified as being affected by EG erosion at least once during the study period. It was observed that most of the gullies, specifically 41 of them, appeared only once in their respective microwatersheds during the whole of that time. Of the 14 remaining ones, one of them appeared in 7 out of the 8 years studied, another one in 6 of the years, 2 of them appeared 5 times, another 2 did so on 4 occasions, 6 on 3 occasions and 5 on 2 occasions. The factors explaining that repeatability, or its absence, are not clear, although the topographic indicators proposed by De Santisteban et al. (2005) might help to shed some light on them. The places where the channels were formed were not exactly the same in the case of the gullies, which appeared repeatedly. This could be due to interannual variations in the soil's properties or its roughness due to tilling; and also to the nature of the precipitations causing them. A very high correlation was found between the total rainfall of the agricultural year and the total length of ephemeral gullies in the study area (R2= 0.85) in a linear regression between both annual variables. The total lengths of EGs ranged between 250 and 800 m, and the precipitations between 300 and 800 mm. References L. M. De Santisteban, J. Casalí, J. J. López, J. V. Giráldez, J. Poesen and J. Nachtergaele, 2005. Exploring the role of topography in small channel erosion. Earth Surf. Process. Landforms 30, 591-599

Intensive soil organic carbon losses by degradation of alpine Kobresia pasture on the Tibetan Plateau

NASA Astrophysics Data System (ADS)

Schleuss, Per-Marten; Heitkamp, Felix; Seeber, Elke; Spielvogel, Sandra; Miehe, Georg; Guggenberger, Georg; Kuzyakov, Yakov

2015-04-01

Kobresia grasslands of the Tibetan Plateau cover an area of ca. 450,000 km2. They are of high global and regional importance as they store large amounts of carbon (C) and nitrogen (N) and provide food for grazing animals. However, intensive grassland degradation in recent decades destroyed mainly the upper root-mat/soil horizon. This has dramatic consequences for SOC storage against the background of climate change and further grazing pressure. We investigated the impact of pasture degradation on SOC storage and hypothesized that SOC stocks strongly decreased due to a reduction of C-input by roots as consequence of vegetation cover loss by overgrazing, SOM decomposition and soil erosion. We selected a sequence of six degradation stages (DS1-6). As initial trigger of grassland degradation, the high grazing pressure reduces the ability of Kobresia pastures to recover from disturbances (e.g. by freezing and drying events, herbivory, trampling). Once the root mats are destroyed, the occurring root-mat cracks increase due to soil erosion, SOC decomposition and trampling activities of livestock. The SOC stocks and contents decreased along the degradation sequence from intact to highly disturbed stages. Carbon stocks declined from intact Kobresia root mats (DS1) to bare soil patches (DS6) by about 70%. The thickness of the upper soil horizons strongly declined from DS1 to DS6. Considering the bare soil patches (DS6) on average 10 cm of the most fertile topsoil were removed. This clearly suggests that soil erosion strongly contributed to SOC losses, especially from topsoil with highest SOC contents. A strong decrease of the vegetation cover (mainly K. pygmaea) demonstrated that soil degradation also resulted in die-back of K. pygmaea. Consequently, root biomass decreased along the degradation sequence (DS1-2 > DS3-4 > DS5-6), indicating lower belowground C input from roots. We found decreasing δ13C values with increasing degradation stages within the upper 20 cm of soil. Higher δ13C values were found for intact root mats (DS1), whereas lowest δ13C signatures occurred for the highly degraded stages (DS5-6). This observation seems to be unusual, because δ13C values are supposed to increase with increasing decomposition. However, the δ13C signatures agreed well with lignin contents, which increased along the degradation sequence. Since lignin is 13C depleted, the δ13C shift clearly indicates SOM decomposition and relative enrichment of lignin components. Using root biomass as indicator for C- input and δ13C values for SOM decomposition, we could explain 70% of decreasing SOC contents using a multiple linear regression model. We conclude that grassland and soil degradation led to large SOC loss due an absence of root C-input, SOM decomposition and soil erosion.

Exploring innovative techniques for identifying geochemical elements as fingerprints of sediment sources in an agricultural catchment of Argentina affected by soil erosion.

PubMed

Torres Astorga, Romina; de Los Santos Villalobos, Sergio; Velasco, Hugo; Domínguez-Quintero, Olgioly; Pereira Cardoso, Renan; Meigikos Dos Anjos, Roberto; Diawara, Yacouba; Dercon, Gerd; Mabit, Lionel

2018-05-15

Identification of hot spots of land degradation is strongly related with the selection of soil tracers for sediment pathways. This research proposes the complementary and integrated application of two analytical techniques to select the most suitable fingerprint tracers for identifying the main sources of sediments in an agricultural catchment located in Central Argentina with erosive loess soils. Diffuse reflectance Fourier transformed in the mid-infrared range (DRIFT-MIR) spectroscopy and energy-dispersive X-ray fluorescence (EDXRF) were used for a suitable fingerprint selection. For using DRIFT-MIR spectroscopy as fingerprinting technique, calibration through quantitative parameters is needed to link and correlate DRIFT-MIR spectra with soil tracers. EDXRF was used in this context for determining the concentrations of geochemical elements in soil samples. The selected tracers were confirmed using two artificial mixtures composed of known proportions of soil collected in different sites with distinctive soil uses. These fingerprint elements were used as parameters to build a predictive model with the whole set of DRIFT-MIR spectra. Fingerprint elements such as phosphorus, iron, calcium, barium, and titanium were identified for obtaining a suitable reconstruction of the source proportions in the artificial mixtures. Mid-infrared spectra produced successful prediction models (R 2  = 0.91) for Fe content and moderate useful prediction (R 2  = 0.72) for Ti content. For Ca, P, and Ba, the R 2 were 0.44, 0.58, and 0.59 respectively.

Reprint of: The evil of sluits: a re-assessment of soil erosion in the Karoo of South Africa as portrayed in century-old sources.

PubMed

Rowntree, K M

2014-06-01

Deep, linear gullies are a common feature of the present landscape of the Karoo of South Africa, where they were known locally in the early twentieth century as 'sluits'. Recent research has shown that many of these features are now stable and are no longer significant sediment sources, although they are efficient connectors in the landscape. Because most of the gully networks predate the first aerial photographs, little is known in the scientific literature about the timing of their formation. One secondary source, however, throws interesting light on the origin of these features, and the early response by landowners to their rehabilitation. The Agricultural Journal of the Cape of Good Hope at the turn of the Twentieth Century carried a number of articles by farmers and agricultural officers concerning the "evil of sluits". The authors gave accounts of widespread incision of valley bottoms by deep, wide gullies. Many of these gullies had been in existence for some thirty years but apparently had formed within living memory. A number of attempts to prevent further erosion had been put in place at the time of writing. This paper presents a review of land degradation, specifically gully erosion, and rehabilitation recommendations as given by authors writing in this journal. It reflects on the findings in the context of assessing land degradation processes through the local knowledge portrayed in the journal. Copyright © 2014. Published by Elsevier Ltd.

The evil of sluits: a re-assessment of soil erosion in the Karoo of South Africa as portrayed in century-old sources.

PubMed

Rowntree, K M

2013-11-30

Deep, linear gullies are a common feature of the present landscape of the Karoo of South Africa, where they were known locally in the early twentieth century as 'sluits'. Recent research has shown that many of these features are now stable and are no longer significant sediment sources, although they are efficient connectors in the landscape. Because most of the gully networks predate the first aerial photographs, little is known in the scientific literature about the timing of their formation. One secondary source, however, throws interesting light on the origin of these features, and the early response by landowners to their rehabilitation. The Agricultural Journal of the Cape of Good Hope at the turn of the Twentieth Century carried a number of articles by farmers and agricultural officers concerning the "evil of sluits". The authors gave accounts of widespread incision of valley bottoms by deep, wide gullies. Many of these gullies had been in existence for some thirty years but apparently had formed within living memory. A number of attempts to prevent further erosion had been put in place at the time of writing. This paper presents a review of land degradation, specifically gully erosion, and rehabilitation recommendations as given by authors writing in this journal. It reflects on the findings in the context of assessing land degradation processes through the local knowledge portrayed in the journal. Copyright © 2013 Elsevier Ltd. All rights reserved.

The litter cover of citrus leaves control soil and water losses in chemically managed orchards

NASA Astrophysics Data System (ADS)

Cerdà, A.; Jurgensen, M. F.; González-Peñaloza, F. A.

2012-04-01

Soil erosion in chemically managed orchards results in bare soil due to the removal of the weeds and the lack of catch crops. Those conditions results in extremely high erosion rates in citrus orchards (Cerdà et al., 2011) such it has been found in other orchards in the Mediterranean where the soil degradation trigger a change in the soil water properties (Gómez et al., 1999). The Mediterranean climatic and human conditions contribute to very active soil water erosion (Ruiz Sinoga et al., 2010) where rilling and piping are found (Romero-Diaz, 2007). It is widely known that high erosion rates can trigger the soil degradation such it has been found in vineyards (Ramos and Martínez Casasnovas, 2006), Olive (García Orenes et al., 2010) and other crops, which is related to the land management and land use (García Ruiz, 2010). Within the chemically managed citrus orchards, the surface cover is usually bare due to the removal of the pruned branches (usually burned) and the use of herbicides every season. A thin and non-continuous litter layer of leaves from the citrus trees covers the soil surface, which sometimes are removed by the farmers to keep the soil clean. There is no information about the effect of the citrus leaves effects on soil and water losses. The objective of this paper is to quantify the effect of the leaves cover on the surface runoff and soil losses. Experiments were conducted by means of simulated rainfall at 55 mm h-1 during one hour in a small circular plot (0.25 m2) to quantify in the field the effect of different litter cover on soil erosion and water losses. An orchard of orange trees (Navel-lane-late, 10 year old, and planted at 6 x 5m with a 45 % cover) was selected in the Municipality of Montesa. Witin the 2 ha field 35 plots were selected with litter covers from 0 to 100 % cover. The runoff discharge was measured every minute and each 5 minutes a sample for runoff sediment concentration was collected. The sediment concentration was measured by dessication. All the measurements were conducted during the summer (August 2008). The results show that the litter cover control the erosion processes. The orange leaves lying on the floor can reduce the soil losses to negligible values when the cover is higher than 60 %. After 20 % of litter cover the soil losses are dramatically reduced to values lower than 50 % of the soil losses under bare soil conditions. The litter cover also reduces the runoff rates, but the reduction is in 50 % for 80 % litter cover. The 20 % litter cover results only in a small reduction in the runoff discharge. The research conducted demonstrate that the farmers should maintain the leaves on the floor (do not brush them as they use to do) to control the high erosion rates. This research study is being supported by the the research project CGL2008-02879/BTE

The viability of prescribed fire for mitigating the soil degradational impacts of wildfire

NASA Astrophysics Data System (ADS)

Shakesby, R. A.; Bento, C. P. M.; Ferreira, C. S. S.; Ferreira, A. J. D.; Stoof, C. R.; Urbanek, E.; Walsh, R. P. D.

2012-04-01

Prescribed (controlled) fire has become an important strategy primarily to limit the likelihood of more devastating wildfire. The considerable increase in wildfire activity in recent decades throughout the Mediterranean, and in Portugal in particular, has meant that this strategy has become increasingly popular despite inherent fears of people about fire of any sort. Despite many studies of the impact of wildfire on soil erosion and degradation, relatively little research has assessed impacts of prescribed fire on soil in Portugal or elsewhere in the Mediterranean. As part of the DESIRE research programme, this paper addresses this research gap by investigating hillslope-scale losses of soil, soil organic matter and selected nutrients before and after an experimental fire (representing a 'worst case-scenario' prescribed fire) in a shrub-vegetated catchment in central Portugal. Comparison is provided by post-fire monitoring of a nearby hillslope affected by a wildfire of moderate severity. Hillslope-scale measurements were carried out over c. 3 years using sediment fences with contributing areas of up to c. 0.5 ha. Eroded sediment was periodically removed from the fences both before and after the fire at intervals ranging from a few weeks to several months depending on rainfall characteristics and logistics. Erosion expressed as g/m2 and g/m2/mm of rainfall was determined. Figures for long-term (c. 10 years) erosion under unburnt conditions for this vegetation type were obtained from a small bounded plot and from sediment accumulating in a weir pool draining a sub-catchment within the prescribed-fire catchment. In addition, soil organic matter and selected nutrients, including K2O, P2O5 and Total N, were measured in the eroded sediment and in the pre-burn and post-burn in situ soil. The results indicate that both the wildfire and prescribed fire caused erosion that was orders of magnitude higher than for long-term plot-scale and hillslope-scale erosion recorded under unburnt conditions. Total post-fire erosion measured over 21 /2 years was relatively high for this worst case scenario prescribed fire even when compared with published results from smaller-scale plots monitored after wildfire elsewhere in the Mediterranean, which would be expected to be higher. Nevertheless, the post-fire hillslope-scale losses appear to have had a relatively low impact on the thin, stony, degraded soils. This is thought also to be the case following the wildfire, even though it caused somewhat higher erosion. Its other serious effects (damage to habitat and property, loss of life), however, mean that wildfire can never be viewed as acceptable, particularly where people live in close proximity to highly fire-prone terrain. The results support the viability of prescribed fire as a strategy for combating wildfire on shrub-vegetated terrain in this wet Mediterranean environment. This view of a low impact of prescribed fire on the terrain may be different where the stability of the soil is reduced by disturbance through ploughing, where soils are very thin or contain relatively few stones, or where fire is carried out too frequently.

[Sediment-yielding process and its mechanisms of slope erosion in wind-water erosion crisscross region of Loess Plateau, Northwest China].

PubMed

Tuo, Deng-Feng; Xu, Ming-Xiang; Zheng, Shi-Qing; Li, Qiang

2012-12-01

Due to the coupling effects of wind and water erosions in the wind-water erosion crisscross region of Loess Plateau, the slope erosion in the region was quite serious, and the erosion process was quite complicated. By using wind tunnel combined with simulated rainfall, this paper studied the sediment-yielding process and its mechanisms of slope erosion under the effects of wind-water alternate erosion, and quantitatively analyzed the efffects of wind erosion on water erosion and the relationships between wind and water erosions. There was an obvious positive interaction between wind and water erosions. Wind erosion promoted the development of microtopography, and altered the quantitative relationship between the sediment-yielding under water erosion and the variation of rainfall intensity. At the rainfall intensity of 60 and 80 mm x h(-1), the sediment-yielding without wind erosion decreased with the duration of rainfall and tended to be stable, but the sediment-yielding with wind erosion decreased to a certain valley value first, and then showed an increasing trend. At the rainfall intensity of 60, 80, and 100 mm x h(-1), the sediment-yielding with the wind erosion at speeds of 11 and 14 m x s(-1) increased by 7.3%-27.9% and 23.2%-39.0%, respectively, as compared with the sediment-yielding without wind erosion. At the rainfall intensity of 120 and 150 mm x h(-1) and in the rainfall duration of 15 minutes, the sediment-yielding with and without wind erosion presented a decreasing trend, but, with the increase of rainfall duration, the sediment-yielding with wind erosion showed a trend of decreasing first and increasing then, as compared with the sediment-yielding without wind erosion. The mechanisms of wind-water alternate erosion were complicated, reflecting in the mutual relation and mutual promotion of wind erosion and water erosion in the aspects of temporal-spatial distribution, energy supply, and action mode of erosion forces.

Conception de couches minces tribologiques pour augmenter la resistance a l'erosion par impacts de particules

NASA Astrophysics Data System (ADS)

Hassani, Salim

Solid particle erosion (SPE) is a serious problem in gas turbines, pumps, heat exchangers and piping systems in aircrafts and other applications. Sand and dust ingested by gas turbine engines may cause major damage to compressor gas path components, leading to severe performance degradation, excessive wear, increased maintenance and eventually premature failure of the engines. For the compressor section of aerospace gas turbine engines, in addition to the complex filtration systems used to screen the eroding particles, tribological coatings, such as TiN, Ti/TiN, CrN and TiAlN are used as protective layers of the base titanium alloy (Ti-6Al-4V) or stainless steels (17-4PH and 410) materials (substrates) against erosive wear. Such coatings can extend the service life of the components, but their performance still remains insufficient due to the complexity of failure mechanisms occurring upon SPE. Therefore, aerospace industry seeks to develop high performance coatings for the protection against erosion by solid particles. However, with many new materials used and tested for different applications and operation under different conditions, conducting experiments for each one of them is becoming increasingly difficult. Presently, coating selection criteria to prevent damage caused by erosion are based on trial and error experiments instead of prior design of coating's architecture and properties to maximize erosion resistance. The present work focuses on the use of advanced finite element (FE) methods to design erosion resistant (ER) coatings. It contributes a new methodology based on the analysis of transient stresses generated by a single impact event. Identification of coating architectures in which such stresses are minimized and crack propagation suppressed, allows one to predict and possibly minimize the erosion rate. Erosion mechanisms and governing erosion parameters are investigated to predict the coating behavior in simulated erosion conditions. The calculation variables include impact velocity (in the range of 50--300 m/s), particle size and the mechanical properties of both the target and the impacting particle. Specifically, we investigate the impact response of coatings fabricated by physical vapor deposition (PVD) and plasma enhanced chemical vapor deposition (PECVD). This includes single and multilayer TiN and nanocomposite nc-TiN/a-SiN1.3 and nc-TiCN/a-SiCN systems on titanium alloy and stainless steel substrates. In particular, we correlate the thickness and the coating macroscopic properties, such as hardness, Young's modulus, and toughness with the erosion. The calculations confirmed earlier findings that for a single layer coating, a combination of low modulus and a high thickness lead to local stress reduction and hence possible erosion resistance enhancement. The FE simulations have further shown that a tensile stress exceeding a critical stress sigmacrit = 3.95 GPa can be easily produced by a single particle impact. For each combination of particle velocity and size, a map of tensile stresses in the TiN coating, corresponding to the predicted erosion performance, was produced. The FE model has then been extended to multilayer coating systems containing superhard nanocomposite materials. These coatings configurations, when combined with tailored mechanical properties have shown to provide an improvement of the performance over comparable single layer configurations. The development of high performance erosion-resistant coatings also requires understanding of stress propagation upon particle impact. In the second part of this work, we apply a finite element methodology to enhance and optimize the resistance of protective coatings to erosion by solid particles with appropriate stress management. A controlled distribution of the initial residual stress in the coating was used to counteract impact stress, while a Young's modulus distribution was applied to optimize impact energy spreading throughout the coating system. Considering both tensile stress reduction and energy absorption, a multi-layer configuration with specific Young's modulus and residual stress distributions along the coating depth is suggested as an optimal coating architecture. In the third part of this work, we propose practical semi-empirical and numerical predictive methods to determine erosion resistance of tribological coatings. The study presents data obtained by FE calculations that can be compared with those obtained by classical theories developed for the erosion of materials. The simulation-based approach allows one to express the functional dependence of erosion on the coating properties, and to quantitatively predict the erosion rate. We determined a proportionality coefficient for a wide range of hard coatings. This coefficient was then used, in combination with the semi-empirical expression derived from FE simulations, to determine the erosion rate of different coatings. The existing erosion theories tend to emphasize hardness, H, and Young's modulus, E, as the main parameters defining erosion resistance. In this context, we specifically focus here on the role of the H/E and H3/E 2 ratios. We demonstrate that the latter characteristics allow one to rank coatings with respect to their erosion performance. Target values for these two ratios were determined for an optimal erosion resistance. We demonstrate that the FE design of the coating architecture, combined with the tailored mechanical properties of individual components of the coating systems, opens new opportunities as a predictive tool for high performance erosion coatings. The present thesis also includes a complementary experimental study of a new kind of ER coatings. We modify the surface profile of hard coatings such as diamond like carbon (DLC) and chrome silicon nitride CrSiN in attempt to correlate the surface characteristics to the functional performance. A specific surface texture (or pattern), designed to enhance erosion resistance, was obtained using a simple and cost effective method consisting of a masking operation, followed by conventional film fabrication techniques PVD or PECVD. Micro-patterned coatings (MPC) possessing specific 3D profiles were produced. In addition to a high potential for several tribological applications, MPC allowed to provide erosion resistance enhancement by a factor of 30 compared to the non-coated stainless steel and of 3--5 times compared to that of the same coating without micro pattern.

Quantifying sediment loadings from streambank erosion in selected agricultural watersheds draining to Lake Champlain

USDA-ARS?s Scientific Manuscript database

At its mouth on Lake Champlain the Missisquoi River has a history of exceedance of phosphorus concentration target levels endorsed by the governments of Vermont, Québec, and New York. Observations along the study reach of the Missisquoi River and several of its tributaries have indicated that the r...

Surface Analysis and Tools

NASA Technical Reports Server (NTRS)

Miyoshi, Kazuhisa

2002-01-01

This article is a chapter of the book entitled, "Tribology of Mechanical Systems," to be published by ASME Press, New York, NY. It describes selected analytical techniques, which are being used in understanding phenomena and mechanisms of oxidation, adhesion, bonding, friction, erosion, abrasion, and wear, and in defining the problems. The primary emphasis is on microanalytical approaches to engineering surfaces.

The Impact of Provincial Policies on University Research. A Comparative Study of Selected Canadian Provinces.

ERIC Educational Resources Information Center

Brochu, Mireille

This report reviews and compares the impact of university support policies in Ontario to those of Quebec, Alberta, and British Columbia and proposes a framework to regenerate the research infrastructure of Ontario universities. It identifies erosion in Ontario's comparative and competitive position within Canada though Ontario still performs about…

Determining soil erosion from roads in coastal plain of Alabama

Treesearch

McFero Grace; W.J. Elliot

2008-01-01

This paper reports soil losses and observed sediment deposition for 16 randomly selected forest road sections in the National Forests of Alabama. Visible sediment deposition zones were tracked along the stormwater flow path to the most remote location as a means of quantifying soil loss from road sections. Volumes of sediment in deposition zones were determined by...

Possibilities of the particle finite element method for fluid-soil-structure interaction problems

NASA Astrophysics Data System (ADS)

Oñate, Eugenio; Celigueta, Miguel Angel; Idelsohn, Sergio R.; Salazar, Fernando; Suárez, Benjamín

2011-09-01

We present some developments in the particle finite element method (PFEM) for analysis of complex coupled problems in mechanics involving fluid-soil-structure interaction (FSSI). The PFEM uses an updated Lagrangian description to model the motion of nodes (particles) in both the fluid and the solid domains (the later including soil/rock and structures). A mesh connects the particles (nodes) defining the discretized domain where the governing equations for each of the constituent materials are solved as in the standard FEM. The stabilization for dealing with an incompressibility continuum is introduced via the finite calculus method. An incremental iterative scheme for the solution of the non linear transient coupled FSSI problem is described. The procedure to model frictional contact conditions and material erosion at fluid-solid and solid-solid interfaces is described. We present several examples of application of the PFEM to solve FSSI problems such as the motion of rocks by water streams, the erosion of a river bed adjacent to a bridge foundation, the stability of breakwaters and constructions sea waves and the study of landslides.

Environmental and engineering effects of sinkholes - the processes behind the problems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Beck, B.F.

1988-10-01

Karstic erosion of the land surface is controlled by processes occurring in the epikarstic zone-the upper portion of the limestone which is most intensely dissolved. Sinkholes developing today are generally the effects of downward movement of mantling sediment into the major karren shafts which drain the epikarstic zone deeper into the true karstic aquifer. Dissolution of the limestone itself does not cause significant changes in man's time frame. The downward erosion of mantling sediment is termed ravelling. Only in uniform sediment will an arched cavity occur. In unconsolidated sediment which is stratified, lateral tunneling may even occur. Only the majormore » karren can transmit sediment downward, the majority are ineffective. In mantled karst the location of surficial depressions and photo-linears does not necessarily correlate to areas of new collapse. The irregular and highly dissolved character of the epikarstic zone complicates foundation engineering. Downward drainage through this zone may be limited and cause flooding. An understanding of processes in the epikarstic zone is essential in developing on karst.« less

Glacial removal of late Cenozoic subglacially emplaced volcanic edifices by the West Antarctic ice sheet

USGS Publications Warehouse

Behrendt, John C.; Blankenship, D.D.; Damaske, D.; Cooper, A. K.

1995-01-01

Local maxima of the horizontal gradient of pseudogravity from closely spaced aeromagnetic surveys over the Ross Sea, northwestern Ross Ice Shelf, and the West Antarctic ice sheet, reveal a linear magnetic rift fabric and numerous subcircular, high-amplitude anomalies. Geophysical data indicate two or three youthful volcanic edifices at widely separated areas beneath the sea and ice cover in the West Antarctic rift system. In contrast, we suggest glacial removal of edifices of volcanic sources of many more anomalies. Magnetic models, controlled by marine seismic reflection and radar ice-sounding data, allow us to infer that glacial removal of the associated late Cenozoic volcanic edifices (probably debris, comprising pillow breccias, and hyaloclastites) has occurred essentially concomitantly with their subglacial eruption. "Removal' of unconsolidated volcanic debris erupted beneath the ice is probably a more appropriate term than "erosion', given its fragmented, ice-contact origin. The exposed volcanoes may have been protected from erosion by the surrounding ice sheet because of more competent rock or high elevation above the ice sheet. -from Authors

Fine scale monitoring of ice ablation following convective heat transfer: case study based on ice-wedge thermo-erosion on Bylot Island (Canadian High Arctic) and laboratory observations

NASA Astrophysics Data System (ADS)

Godin, E.; Fortier, D.

2011-12-01

Thermo-erosion gullies often develop in ice-wedge polygons terrace and contribute to the dynamic evolution of the periglacial landscape. When snowmelt surface run-off concentrated into streams and water tracks infiltrate frost cracks, advective heat flow and convective thermal transfer from water to the ice-wedge ice enable the rapid development of tunnels and gullies in the permafrost (Fortier et al. 2007). Fine scale monitoring of the physical interaction between flowing water and ice rich permafrost had already been studied in a context of thermal erosion of a large river banks in Russia (Costard et al. 2003). Ice wedge polygons thermo-erosion process leading to gullying remains to be physically modelled and quantified. The present paper focus on the fine scale monitoring of thermo-erosion physical parameters both in the field and in laboratory. The physical model in laboratory was elaborated using a fixed block of ice monitored by a linear voltage differential transducer (LVDT) and temperature sensors connected to a logger. A water container with controlled discharge and temperature provided the fluid which flowed over the ice through a hose. Water discharge (Q), water temperature (Tw), ice melting temperature (Ti) and ice ablation rate (Ar) were measured. In laboratory, water at 281 Kelvin (K) flowing on the ice (Ti 273 K) made the ice melt at a rate Ar of 0.002 m min-1, under a continuous discharge of ≈ 8 x 10-7 m3 s-1. In the field, a small channel was dug between a stream and an exposed ice-wedge in a pre-existing active gully, where in 2010 large quantities of near zero snowmelt run-off water contributed to several meters of ice wedge ablation and gully development. Screws were fastened into the ice and a ruler was used to measure the ablation rate every minute. The surface temperature of the ice wedge was monitored with thermocouples connected to a logger to obtain the condition of the ice boundary layer. Discharge and water temperature were measured in the excavated channel just before the water got in contact with the ice surface. The field experiment where flowing water at Tw = 277 K, Ti = 273 K with a water discharge of 0.01 m3 s-1 resulted in a measured Ar of 0.01 to 0.02 m min-1. Water discharge and temperature difference between water and the melting ice were fundamental to ice ablation rate. The recent climate warming in the Canadian High Arctic will likely strongly contribute to the interaction and importance of the thermo-erosion and gullying processes in the High Arctic. Combined factors such as earlier or faster snowmelt, precipitation changes during the summer and positive feedback effects will probably increase the hydrological input to gullies and therefore enhance their development by thermo-erosion. Costard F. et al. 2003. Fluvial thermal erosion investigations along a rapidly eroding river bank: Application to the Lena River (central Siberia). Earth Surface Processes and Landforms 28: 1349-1359. Fortier D. et al. 2007. Observation of rapid drainage system development by thermal erosion of ice wedges on Bylot island, Canadian Arctic Archipelago. Permafrost and Periglacial Processes 18: 229-243.

Channel morphodynamics in four reaches of the Lower Missouri River, 2006-07

USGS Publications Warehouse

Elliott, Caroline M.; Reuter, Joanna M.; Jacobson, Robert B.

2009-01-01

Channel morphodynamics in response to flow modifications from Gavins Point Dam are examined in four reaches of the Lower Missouri River. Measures include changes in channel morphology and indicators of sediment transport in four 6 kilometer long reaches located downstream from Gavins Point Dam, near Yankton, South Dakota, Kenslers Bend, Nebraska, Little Sioux, Iowa, and Miami, Missouri. Each of the four reaches was divided into 300 transects with a 20-meter spacing and surveyed during the summer in 2006 and 2007. A subset of 30 transects was randomly selected and surveyed 7-10 times in 2006-07 over a wide range of discharges including managed and natural flow events. Hydroacoustic mapping used a survey-grade echosounder and a Real Time Kinematic Global Positioning System to evaluate channel change. Acoustic Doppler current profiler measurements were used to evaluate bed-sediment velocity. Results indicate varying amounts of deposition, erosion, net change, and sediment transport in the four Lower Missouri River reaches. The Yankton reach was the most stable over monthly and annual time-frames. The Kenslers Bend and Little Sioux reaches exhibited substantial amounts of deposition and erosion, although net change was generally low in both reaches. Total, or gross geomorphic change was greatest in the Kenslers Bend reach. The Miami reach exhibited varying rates of deposition and erosion, and low net change. The Yankton, Kenslers Bend, and Miami reaches experienced net erosion during the time period that bracketed the managed May 2006 spring rise event from Gavins Point Dam.

The early cretaceous evolution of carbonate platforms from northern Oman

DOE Office of Scientific and Technical Information (OSTI.GOV)

Masse, J.P.; Borgomano, J.; Maskiry, S.Al.

1993-09-01

In northern Oman (Jebel Akhdar and foothills) Hauterivian to early Aptian shallow carbonate platforms are widely extending and pass laterally to slope and basin environments in the Nakhl zone. Progradational geometries are identified in that zone where significant correlation between thickness and sediment types supports a prominent tectonic control. The platform records four main sedimentary breaks (drowning events). Early Barremian (lower Lekhwair Formation), Late Barremian (basal Kharaib Formation), lowermost early Aptian (upper Kharaib Formation) and middle Aptian (Shuaiba-Al Hassanat formations boundary). The late Aptian-early Albian hiatus (pre-Nahr Umr unconformity) is regarded as an early Albian tectonically driven erosion. In themore » Nakhl zone, coral-rudist limestones of late Aptian-early Albian (lower Al Hassanat Formation) document an east-west ribbon platform, the southward extension of which was obscured by the middle Albian erosions and rudist limestones of middle to late Albian (upper Al Hassanat Formation), a lateral equivalent of the Nahr Umr circa littoral shaly sediments, document an east-west-trending linear platform. The foregoing points out a northward progradation coeval with a southward transgressive major trend for the Hauterivian-early Aptian interval, a faulted margin corresponding with the Nakhl zone active during the Aptian-Albian, a late Aptian ribbon platform coeval with the Bab basin initiation southward, a regional uplifting and truncation during the early-Albian (Austrian phase), whereas shallow-water carbonates are still forming at the edge of the former platform, and an active linear platform at the northern edge of the Nahr Umr basin, the corresponding drowning contemporaneous with the onset of the Cenomanian platform eastward.« less

Reabilitation of degraded area by erosion, using soil bioengineering techniques in Bacanga river basin, Sao Luis City - Maranhao State, Brazil.

NASA Astrophysics Data System (ADS)

Teixeira Guerra, A. J.; Rodrigues Bezerra, J. F.; da Mota Lima, L. D.; Silva Mendonça, J. K.; Vieira Souza, U. D.; Teixeira Guerra, T.

2009-04-01

The aim of this paper is to assess the stages of rehabilitation of a degraded site by erosion, in Salina/Sacavém district, São Luís City, considering geomorphologic characteristics and soil bioengineering techniques. This technique has been applied in different situations to rehabilitate degraded areas, with positive results from the use of biodegradable materials (e.g. vegetal fibres, wooden stakes and re-vegetation). These techniques stabilize the soil at low cost and improve the environment. Bioengineering involves the planned and strategic application of selected materials, involving biodegradable materials, often in combination with 'hard engineering' structures constructed from stone, concrete and steel. The settlement of São Luís was established in 1612 and has evolved in distinct phases. Rapid urban growth was associated with industrialization in the second half of the 18th Century. Rapid population and urban growth has intensified problems, compounded by poor planning and improper soil use. São Luís, like many other Brazilian cities, has experienced rapid population growth in recent decades, which has created a series of socio-economic and environmental problems, including accelerated soil erosion. Sacavém is one of these communities where natural and human factors contribute to the severe gully erosion. The local lithology is mainly Tertiary sandstones and, to a lesser extent, shales, argillites and siltstones, all of which belong to the Barreiras Formation. Weathering on these rocks produces erodible soils, including lithosols, latosols, concretionary red/yellow clay soils and concretionary plinthosols. Thus, erodible soils and regolith are subject to high erosion rates, especially on steeper slopes subject to additional human interventions. Furthermore, although regional slopes are quite gentle, there is localized high relative relief. Sacavém vegetation, in the gullied area, consists of brushwood. Secondary mixed forest and brushwood are the dominant vegetal cover adjacent to the urban gullies. The local climate is humid tropical, with average annual temperatures of 26°C, reaching higher values in October to December and lower from April to June. Rainfall distribution throughout the year is irregular, marked by two very distinct seasons (rainy and dry). The highly seasonal erosive rains incise a complex series of soil erosion landforms, mainly gullies in this area. The following procedures have been carried out: fieldwork with monitoring of gully head erosion; Environmental Education Program; handcraft workshop regarding the prodution of geotextiles from Buriti fiber. The rehabilitation of this degraded site, follows these stages: 1. Acquisition of equipment and materials; 2. Contracting workers; 3. Reshaping selected gully walls; 4. Adding organic palm materials to the topsoil and ~30 kg of grass seeds; 5. Application of geotextile anchored on the ground by using wooden stakes; 6. Maintenance work with photographic records; 7. Photo comparison to measure the vegetal cover percentage, with the aid of geoprocessing software. Some of the gully walls presented steep slopes, around 90 degrees, and therefore, it was necessary to reshape them for the application of soil bioengineering techniques. It was selected a sample area of 2.000 m2 to be rehabilitated. The knowledge of soil and geomorphological characteristics was essential to understand surface runoff, considering the direction of water flows. Due to the difficulties in diverting the flows, which would require more extensive engineering works, the channel was maintained, and the base of the slopes was strengthened to support the flows. In the upper part of this area, which had ~8° slope angle, contour lines were surveyed and barriers of wooden stakes were used to retard runoff velocity from adjacent vegetated slopes. Some slopes in this part had a 45° slope angle, due to the local topography. However, this angle is considered too steep for the application of palm-mats. In some parts of gully, work was completed to reshape the gullies and construct the ~12 m high terraces using the gully material. Tractor work was impeded, because on the second terrace the tractor had difficulty in working, because of the high sand content, which made the slope unstable. These terraces are crossed by a flow convergence area, which was formed by men inserting sand bags, decomposing palm leaves and grass seeds, to form a vegetated channel after grass growth. Key-words: Rehabilitation, gully, geotextile, soil bioengineering.

Modelling of Sub-daily Hydrological Processes Using Daily Time-Step Models: A Distribution Function Approach to Temporal Scaling

NASA Astrophysics Data System (ADS)

Kandel, D. D.; Western, A. W.; Grayson, R. B.

2004-12-01

Mismatches in scale between the fundamental processes, the model and supporting data are a major limitation in hydrologic modelling. Surface runoff generation via infiltration excess and the process of soil erosion are fundamentally short time-scale phenomena and their average behaviour is mostly determined by the short time-scale peak intensities of rainfall. Ideally, these processes should be simulated using time-steps of the order of minutes to appropriately resolve the effect of rainfall intensity variations. However, sub-daily data support is often inadequate and the processes are usually simulated by calibrating daily (or even coarser) time-step models. Generally process descriptions are not modified but rather effective parameter values are used to account for the effect of temporal lumping, assuming that the effect of the scale mismatch can be counterbalanced by tuning the parameter values at the model time-step of interest. Often this results in parameter values that are difficult to interpret physically. A similar approach is often taken spatially. This is problematic as these processes generally operate or interact non-linearly. This indicates a need for better techniques to simulate sub-daily processes using daily time-step models while still using widely available daily information. A new method applicable to many rainfall-runoff-erosion models is presented. The method is based on temporal scaling using statistical distributions of rainfall intensity to represent sub-daily intensity variations in a daily time-step model. This allows the effect of short time-scale nonlinear processes to be captured while modelling at a daily time-step, which is often attractive due to the wide availability of daily forcing data. The approach relies on characterising the rainfall intensity variation within a day using a cumulative distribution function (cdf). This cdf is then modified by various linear and nonlinear processes typically represented in hydrological and erosion models. The statistical description of sub-daily variability is thus propagated through the model, allowing the effects of variability to be captured in the simulations. This results in cdfs of various fluxes, the integration of which over a day gives respective daily totals. Using 42-plot-years of surface runoff and soil erosion data from field studies in different environments from Australia and Nepal, simulation results from this cdf approach are compared with the sub-hourly (2-minute for Nepal and 6-minute for Australia) and daily models having similar process descriptions. Significant improvements in the simulation of surface runoff and erosion are achieved, compared with a daily model that uses average daily rainfall intensities. The cdf model compares well with a sub-hourly time-step model. This suggests that the approach captures the important effects of sub-daily variability while utilizing commonly available daily information. It is also found that the model parameters are more robustly defined using the cdf approach compared with the effective values obtained at the daily scale. This suggests that the cdf approach may offer improved model transferability spatially (to other areas) and temporally (to other periods).

Comparison of Conventional and ANN Models for River Flow Forecasting

NASA Astrophysics Data System (ADS)

Jain, A.; Ganti, R.

2011-12-01

Hydrological models are useful in many water resources applications such as flood control, irrigation and drainage, hydro power generation, water supply, erosion and sediment control, etc. Estimates of runoff are needed in many water resources planning, design development, operation and maintenance activities. River flow is generally estimated using time series or rainfall-runoff models. Recently, soft artificial intelligence tools such as Artificial Neural Networks (ANNs) have become popular for research purposes but have not been extensively adopted in operational hydrological forecasts. There is a strong need to develop ANN models based on real catchment data and compare them with the conventional models. In this paper, a comparative study has been carried out for river flow forecasting using the conventional and ANN models. Among the conventional models, multiple linear, and non linear regression, and time series models of auto regressive (AR) type have been developed. Feed forward neural network model structure trained using the back propagation algorithm, a gradient search method, was adopted. The daily river flow data derived from Godavari Basin @ Polavaram, Andhra Pradesh, India have been employed to develop all the models included here. Two inputs, flows at two past time steps, (Q(t-1) and Q(t-2)) were selected using partial auto correlation analysis for forecasting flow at time t, Q(t). A wide range of error statistics have been used to evaluate the performance of all the models developed in this study. It has been found that the regression and AR models performed comparably, and the ANN model performed the best amongst all the models investigated in this study. It is concluded that ANN model should be adopted in real catchments for hydrological modeling and forecasting.

Morphology and stratal geometry of the Antarctic continental shelf: Insights from models

USGS Publications Warehouse

Cooper, Alan K.; Barker, Peter F.; Brancolini, Giuliano

1997-01-01

Reconstruction of past ice-sheet fluctuations from the stratigraphy of glaciated continental shelves requires understanding of the relationships among the stratal geometry, glacial and marine sedimentary processes, and ice dynamics. We investigate the formation of the morphology and the broad stratal geometry of topsets on the Antarctic continental shelf with numerical models. Our models assume that the stratal geometry and morphology are principally the results of time-integrated effects of glacial erosion and sedimentation related to the location of the seaward edge of the grounded ice. The location of the grounding line varies with time almost randomly across the shelf. With these simple assumptions, the models can successfully mimic salient features of the morphology and the stratal geometry. The models suggest that the current shelf has gradually evolved to its present geometry by many glacial advances and retreats of the grounding line to different locations across the shelf. The locations of the grounding line do not appear to be linearly correlated with either fluctuations in the 5 l s O record (which presumably represents changes in the global ice volume) or with the global sea-level curve, suggesting that either a more complex relationship exists or local effects dominate. The models suggest that erosion of preglacial sediments is confined to the inner shelf, and erosion decreases and deposition increases toward the shelf edge. Some of the deposited glacial sediments must be derived from continental erosion. The sediments probably undergo extensive transport and reworking obliterating much of the evidence for their original depositional environment. The flexural rigidity and the tectonic subsidence of the underlying lithosphere modify the bathymetry of the shelf, but probably have little effect on the stratal geometry. Our models provide several guidelines for the interpretation of unconformities, the nature of preserved topset deposits, and the significance of progradation versus aggradation of shelf sediments.

Effects of disturbance on vegetation by sand accretion and erosion across coastal dune habitats on a barrier island

PubMed Central

Miller, Thomas E.

2015-01-01

Coastal geomorphology and vegetation are expected to be particularly sensitive to climate change, because of disturbances caused by sea-level rise and increased storm frequency. Dunes have critical reciprocal interactions with vegetation; dunes create habitats for plants, while plants help to build dunes and promote geomorphological stability. These interactions are also greatly affected by disturbances associated with sand movement, either in accretion (dune building) or in erosion. The magnitude and intensity of disturbances are expected to vary with habitat, from the more exposed and less stable foredunes, to low-lying and flood-prone interdunes, to the protected and older backdunes. Permanent plots were established at three different spatial scales on St George Island, FL, USA, where the vegetation and dune elevation were quantified annually from 2011 to 2013. Change in elevation, either through accretion or erosion, was used as a measure of year-to-year disturbance over the 2 years of the study. At the scale of different dune habitats, foredunes were found to have the greatest disturbance, while interdunes had the least. Elevation and habitat (i.e. foredune, interdune, backdune) were significantly correlated with plant community composition. Generalized linear models conducted within each habitat show that the change in elevation (disturbance) is also significantly correlated with the plant community, but only within foredunes and interdunes. The importance of disturbance in exposed foredunes was expected and was found to be related to an increasing abundance of a dominant species (Uniola paniculata) in eroding areas. The significant effect of disturbance in the relatively stable interdunes was surprising, and may be due to the importance of flooding associated with small changes in elevation in these low-lying areas. Overall, this study documents changes in the plant community associated with elevation, and demonstrates that the foredune and interdune communities are also associated with the responses of specific species to local changes in elevation due to accretion or erosion. PMID:25587195

Dynamic Analysis of Soil Erosion in Songhua River Watershed

NASA Astrophysics Data System (ADS)

Zhang, Yujuan; Li, Xiuhai; Wang, Qiang; Liu, Jiang; Liang, Xin; Li, Dan; Ni, Chundi; Liu, Yan

2018-01-01

In this paper, based on RS and GIS technology and Revised Universal Soil Loss Equation (RUSLE), the soil erosion dynamic changes during the two periods of 1990 and 2010 in Bin County was analyzed by using the Landsat TM data of the two periods, so as to reveal the soil erosion spatial distribution pattern and spatial and temporal dynamic evolution rule in the region. The results showed that: the overall patterns of soil erosion were basically the same in both periods, mainly featuring slight erosion and mild erosion, with the area proportions of 80.68% and 74.71% respectively. The slight and extremely intensive erosion changing rates showed a narrowing trend; mild, moderate and intensive erosion was increasing, with a trend of increased soil erosion; mild and intensive erosion were developing towards moderate erosion and moderate and extremely intensive erosion were progressing towards intensive erosion.

Using LiDAR to Estimate Surface Erosion Volumes within the Post-storm 2012 Bagley Fire

NASA Astrophysics Data System (ADS)

Mikulovsky, R. P.; De La Fuente, J. A.; Mondry, Z. J.

2014-12-01

The total post-storm 2012 Bagley fire sediment budget of the Squaw Creek watershed in the Shasta-Trinity National Forest was estimated using many methods. A portion of the budget was quantitatively estimated using LiDAR. Simple workflows were designed to estimate the eroded volume's of debris slides, fill failures, gullies, altered channels and streams. LiDAR was also used to estimate depositional volumes. Thorough manual mapping of large erosional features using the ArcGIS 10.1 Geographic Information System was required as these mapped features determined the eroded volume boundaries in 3D space. The 3D pre-erosional surface for each mapped feature was interpolated based on the boundary elevations. A surface difference calculation was run using the estimated pre-erosional surfaces and LiDAR surfaces to determine volume of sediment potentially delivered into the stream system. In addition, cross sections of altered channels and streams were taken using stratified random selection based on channel gradient and stream order respectively. The original pre-storm surfaces of channel features were estimated using the cross sections and erosion depth criteria. Open source software Inkscape was used to estimate cross sectional areas for randomly selected channel features and then averaged for each channel gradient and stream order classes. The average areas were then multiplied by the length of each class to estimate total eroded altered channel and stream volume. Finally, reservoir and in-channel depositional volumes were estimated by mapping channel forms and generating specific reservoir elevation zones associated with depositional events. The in-channel areas and zones within the reservoir were multiplied by estimated and field observed sediment thicknesses to attain a best guess sediment volume. In channel estimates included re-occupying stream channel cross sections established before the fire. Once volumes were calculated, other erosion processes of the Bagley sedimentation study, such as surface soil erosion were combined to estimate the total fire and storm sediment budget for the Squaw Creek watershed. The LiDAR-based measurement workflows can be easily applied to other sediment budget studies using one high resolution LiDAR dataset.

High heat flux testing of CFC composites for the tokamak physics experiment

NASA Astrophysics Data System (ADS)

Valentine, P. G.; Nygren, R. E.; Burns, R. W.; Rocket, P. D.; Colleraine, A. P.; Lederich, R. J.; Bradley, J. T.

1996-10-01

High heat flux (HHF) testing of carbon fiber reinforced carbon composites (CFC's) was conducted under the General Atomics program to develop plasma-facing components (PFC's) for Princeton Plasma Physics Laboratory's tokamak physics experiment (TPX). As part of the process of selecting TPX CFC materials, a series of HHF tests were conducted with the 30 kW electron beam test system (EBTS) facility at Sandia National Laboratories, and with the plasma disruption simulator I (PLADIS-I) facility at the University of New Mexico. The purpose of the tests was to make assessments of the thermal performance and erosion behavior of CFC materials. Tests were conducted with 42 different CFC materials. In general, the CFC materials withstood the rapid thermal pulse environments without fracturing, delaminating, or degrading in a non-uniform manner; significant differences in thermal performance, erosion behavior, vapor evolution, etc. were observed and preliminary findings are presented below. The CFC's exposed to the hydrogen plasma pulses in PLADIS-I exhibited greater erosion rates than the CFC materials exposed to the electron-beam pulses in EBTS. The results obtained support the continued consideration of a variety of CFC composites for TPX PFC components.

Discordant introgression in a rapidly expanding hybrid swarm

USGS Publications Warehouse

Ward, Jessica L.; Blum, Mike J.; Walters, David M.; Porter, Brady A.; Burkhead, Noel; Freeman, Byron

2012-01-01

The erosion of species boundaries can involve rapid evolutionary change. Consequently, many aspects of the process remain poorly understood, including the formation, expansion, and evolution of hybrid swarms. Biological invasions involving hybridization present exceptional opportunities to study the erosion of species boundaries because timelines of interactions and outcomes are frequently well known. Here, we examined clinal variation across codominant and maternally inherited genetic markers as well as phenotypic traits to characterize the expansion and evolution of a hybrid swarm between native Cyprinella venusta and invasive Cyprinella lutrensis minnows. Discordant introgression of phenotype, microsatellite multilocus genotype, and mtDNA haplotype indicates that the observable expansion of the C. venusta x C. lutrensis hybrid swarm is a false invasion front. Both parental and hybrid individuals closely resembling C. lutrensis are numerically dominant in the expansion wake, indicating that the non-native parental phenotype may be selectively favored. These findings show that cryptic introgression can extend beyond the phenotypic boundaries of hybrid swarms and that hybrid swarms likely expand more rapidly than can be documented from phenotypic variation alone. Similarly, dominance of a single parental phenotype following an introduction event may lead to instances of species erosion being mistaken for species displacement without hybridization.

Medicinal plant knowledge and its erosion among the Mien (Yao) in northern Thailand.

PubMed

Srithi, Kamonnate; Balslev, Henrik; Wangpakapattanawong, Prasit; Srisanga, Prachaya; Trisonthi, Chusie

2009-06-22

We studied local knowledge and actual uses of medicinal plants among the Mien in northern Thailand, documenting traditional medical practices and its transfer between generations. With the assumption that discrepancies between knowledge and actual use represent knowledge erosion, we studied whether actual use of medicinal plants corresponded to people's knowledge of such uses. We used local knowledge from four specialist informants as the domain for semi-structured interviews with 34 randomly selected non-specialist informants. We calculated informant consensus, use value, and fidelity level for each species and use category and performed statistical analyses with Kolmogorov-Smirnov tests, Pearson correlation coefficient, Spearman's rank correlation coefficient, and paired-sample t-tests. We found significant discrepancies between knowledge and actual use of medicinal plants. The number of known and actually used plants increased with increasing informant age and decreased with increasing years of formal education. Medicinal plant knowledge and use in these Mien communities is undergoing inter-generational erosion because of acculturation and interrupted knowledge transmission. Preservation of Mien medicinal plant intellectual heritage requires continued documentation concerning use, conservation, and sustainable management of this resource, which should be publicized to younger Mien.

Coupling a basin erosion and river sediment transport model into a large scale hydrological model: an application in the Amazon basin

NASA Astrophysics Data System (ADS)

Buarque, D. C.; Collischonn, W.; Paiva, R. C. D.

2012-04-01

This study presents the first application and preliminary results of the large scale hydrodynamic/hydrological model MGB-IPH with a new module to predict the spatial distribution of the basin erosion and river sediment transport in a daily time step. The MGB-IPH is a large-scale, distributed and process based hydrological model that uses a catchment based discretization and the Hydrological Response Units (HRU) approach. It uses physical based equations to simulate the hydrological processes, such as the Penman Monteith model for evapotranspiration, and uses the Muskingum Cunge approach and a full 1D hydrodynamic model for river routing; including backwater effects and seasonal flooding. The sediment module of the MGB-IPH model is divided into two components: 1) prediction of erosion over the basin and sediment yield to river network; 2) sediment transport along the river channels. Both MGB-IPH and the sediment module use GIS tools to display relevant maps and to extract parameters from SRTM DEM (a 15" resolution was adopted). Using the catchment discretization the sediment module applies the Modified Universal Soil Loss Equation to predict soil loss from each HRU considering three sediment classes defined according to the soil texture: sand, silt and clay. The effects of topography on soil erosion are estimated by a two-dimensional slope length (LS) factor which using the contributing area approach and a local slope steepness (S), both estimated for each DEM pixel using GIS algorithms. The amount of sediment releasing to the catchment river reach in each day is calculated using a linear reservoir. Once the sediment reaches the river they are transported into the river channel using an advection equation for silt and clay and a sediment continuity equation for sand. A sediment balance based on the Yang sediment transport capacity, allowing to compute the amount of erosion and deposition along the rivers, is performed for sand particles as bed load, whilst no erosion or deposition is allowed for silt and clay. The model was first applied on the Madeira River basin, one of the major tributaries of the Amazon River (~1.4*106 km2) accounting for 35% of the suspended sediment amount annually transported for the Amazon river to the ocean. Model results agree with observed data, mainly for monthly and annual time scales. The spatial distribution of soil erosion within the basin showed a large amount of sediment being delivered from the Andean regions of Bolivia and Peru. Spatial distribution of mean annual sediment along the river showed that Madre de Dios, Mamoré and Beni rivers transport the major amount of sediment. Simulated daily suspended solid discharge agree with observed data. The model is able to provide temporaly and spatialy distributed estimates of soil loss source over the basin, locations with tendency for erosion or deposition along the rivers, and to reproduce long term sediment yield at several locations. Despite model results are encouraging, further effort is needed to validate the model considering the scarcity of data at large scale.

Hillslope-channel coupling in a steep Hawaiian catchment accelerates erosion rates over 100-fold

NASA Astrophysics Data System (ADS)

Stock, J. D.; Hanshaw, M. N.; Rosener, M.; Schmidt, K. M.; Brooks, B. A.; Tribble, G.; Jacobi, J.

2009-12-01

In tropical watersheds, hillslope changes are producing increasing amounts of fine sediment that can be quickly carried to reefs by channels. Suspended sediment concentrations off the reefs of Molokai, Hawaii, chronically exceed a toxic level of 10 mg/L, threatening reef ecosystems. We hypothesize that historic conversion of watersheds from soil creep to overland flow erosion increased both magnitude and frequency of sediment flooding adjacent reefs. We combined surficial and ecological mapping, hillslope and stream gages, and novel sensors to locate, quantify and model the generation of fine sediments polluting the Molokai reef. Ecological and geomorphic mapping from LiDAR and multi-spectral imagery located a subset of overland flow areas with vegetation cover below a threshold value preventing erosion. Here, feral goat grazing exposed cohesive volcanic soils whose low matrix hydraulic conductivities (1-20 mm/hour) promote Horton overland flow erosion. We instrumented steep, barren hillslopes with soil moisture sensors, overland flow meters, Parshall flumes, ISCO sediment samplers, and a rain gage and conducted repeat Tripod LiDAR and infiltration tests. To characterize soil resistance here and elsewhere to overland flow erosion, we deployed a Cohesive Strength Meter (CSM) to simulate the stresses of flowing water. At the 13.5 km 2 watershed mouth we used a USGS stream gage and ISCO sediment sampler to estimate total load. Over 2 years, storms triggered overland flow during rainfall intensities above 10-15 mm/hr. Overland flow meters indicate such flows can be up to 3 cm deep, with a tendency to deepen downslope. CSM tests indicate that these depths are insufficient to erode soils where vegetation is dense, but far above threshold values of 2-3 mm depth for bare soil erosion. Sediment ratings curves for both hillslope and downstream catchment gages show strong clock-wise hysteresis during the first intense storms in the Fall, becoming linear later in the rainy season. During Fall storms, sediment concentration is often 10X higher at a given stage. During intense Fall storms, we measured erosion rates using erosion pins (1.0 cm/a), suspended sediment flux (1.5 cm/a) and repeat tripod LiDAR (1.7 cm/a). These rates are at least 100-fold greater than the long-term lowering rate of 0.13 mm/a. A sediment budget constructed by extrapolating hillslope lowering rates to the portions of the catchments mapped as overland flow hotspots predicts a total yearly flux of ~ 6500 t, in agreement with the measured total of ~6200 t. A decadal record illustrates that rainfall intensities sufficient to generate overland flow occur for at least 8-10 hours every year, coincident with 1-3 large storm events. We hypothesize that high lowering rates reflect a combination of long-duration overland flow events, and availability of weathered soils that can be entrained by thin flows. It appears that the generation of loose, seasonally weathered silt is a 1st order control on the amount of sediment exported to the reef. If climate change increases storm frequency or duration, or decreases vegetation cover, sediment loading rates to the reef here could increase dramatically.

The relative importance of different grass components in controlling runoff and erosion on a hillslope under simulated rainfall

NASA Astrophysics Data System (ADS)

Li, Changjia; Pan, Chengzhong

2018-03-01

The effects of vegetation cover on overland flow and erosion processes on hillslopes vary with vegetation type and spatial distribution and the different vegetation components, including the above- and below-ground biomass. However, few attempts have been made to quantify how these factors affect erosion processes. Field experimental plots (5 m × 2 m) with a slope of approximately 25° were constructed and simulated rainfall (60 mm hr-1) (Rainfall) and simulated rainfall combined with upslope overland flow (20 L min-1) (Rainfall + Flow) were applied. Three grass species were planted, specifically Astragalus adsurgens (A. adsurgens), Medicago sativa (M. sativa) and Cosmos bipinnatus (C. bipinnatus). To isolate and quantify the relative contributions of the above-ground grass parts (stems, litter cover and leaves) and the roots to reducing surface runoff and erosion, each of the three grass species was subjected to three treatments: intact grass control (IG), no litter or leaves (only the grass stems and roots were reserved) (NLL), and only roots remaining (OR). The results showed that planting grass significantly reduced overland flow rate and velocity and sediment yield, and the mean reductions were 21.8%, 29.1% and 67.1%, respectively. M. sativa performed the best in controlling water and soil losses due to its thick canopy and dense, fine roots. Grasses reduced soil erosion mainly during the early stage of overland flow generation. The above-ground grass parts primarily contributed to reducing overland flow rate and velocity, with mean relative contributions of 64% and 86%, respectively. The roots played a predominant role in reducing soil erosion, with mean contribution of 84%. Due to the impact of upslope inflow, overland flow rate and velocity and sediment yield increased under the Rainfall + Flow conditions. The results suggest that grass species on downslope parts of semi-arid hillslopes performed better in reducing water and soil losses. This study is beneficial for forage selection, allocation and management practices, such as forage harvesting, when implementing restoration strategies to control soil and water losses.

Zonal characterization of hillslope erosion processes in a semi-arid high mountain catchment

NASA Astrophysics Data System (ADS)

Torres, Raquel; Millares, Agustín; Aguilar, Cristina; Moñino, Antonio; Ángel Losada, Miguel; José Polo, María

2013-04-01

Mediterranean and semi-arid catchments, generally suffer heterogeneous erosive processes at different spatio-temporal scales which produce, in a synergistic manner, a large amount of sediment supply. In mountainous catchments, the influence of pluvio-nival hydrological regime leads to a clear subdivision into homogeneous zones regarding the nature of hillslope processes. Here, a distinction could be addressed with 1) subsurface erosion due to saturated soil by intense snowmelt pulses and 2) steepest mid-mountain soil loss with rill/interrill, small-scale landslides and ephemeral or permanent gullying. Furthermore, the associated channels in these areas are formed by wide alluvial floodplains with important bedload contributions. This complexity conditions the evaluation of erosion and monitoring at catchment scale with elevated costs in time, devices and staff. The catchment of the Guadalfeo river encloses 1200 km², with important presence of snow in the summits height on its right margin, and semiarid low range hills with very erodible soils on its left margin. Gully erosion, landslides and stream bed-load processes, extremely actives in this area, are responsible of a real problem of soil loss and desertification with a high associated cost. This work suggests a methodology for the zonal assessment of different erosive processes taking into account the described heterogeneity and the reduction of research costs. To do this, high resolution bathymetric and topographic surveys supported in a reservoir (110 hm3) allowed the differentiation of bedload and suspended sediments as both are deposited in different locations and hence the validation of the hillslope sediment yield. In parallel, measurements in homogeneous areas were selected in order to obtain zonal results to achieve the representative processes involved. The use of portable samplers allows the remote changing of sampling routines, and thus to capture the temporal scale of the processes and the associated forcing agents. The obtained results validate the proposed methodology with adjustments/fitting between measured suspended sediment regarding the increase of volume registered at the dam. Furthermore, the measures obtained reveal a clear zonal differentiation in sediment yield which represents the heterogeneous dynamic of the processes involved.

Laparoscopic sleeve gastrectomy as revisional surgery for adjustable gastric band erosion.

PubMed

Park, Yeon Ho; Kim, Seong Min

2014-09-01

Laparoscopic sleeve gastrectomy (LSG) has been increasingly adopted as a revisional surgery for failed gastric banding. However, little information is available regarding the outcome of revisional LSG for band erosion. A retrospective database analysis was performed to study LSG as revisional surgery for band erosion. For staged revision, we waited a minimum of 3 months after band removal, and for single-stage revision, the band was removed by gastrotomy, and sleeve gastrectomy was performed at the same time. Main outcome measures were success rates of therapeutic strategies, morbidity, and mortality rates, length of stay, and body mass index (BMI) (percentage excess weight loss [%EWL]) before and after revision. From March 2011 to February 2013, 9 female patients underwent revisional LSG. Average age was 34.7 years. Six patients underwent a staged procedure, and the other 3 underwent a single-stage revision. Among the 6 staged patients, eroded bands had been removed by laparoscopy in 4 and by endoscopy in 2 without complications. Their LSGs were performed at a median of 4.4 months after band removal. Another 2 patients underwent single-stage revision. In the last patient, band erosion was incidentally found during a revisional LSG for insufficient weight loss. No mortality occurred. There were one stenosis and two proximal leaks. Two patients with leak underwent total gastrectomy and fistulojejunostomy. After a mean follow-up of 19.1 months, all 9 patients exhibited weight loss. The mean (±standard deviation [SD]) pre- and post-LSG BMIs were 34.0±4.4 and 25.6±2.1 kg/m(2), respectively, and their mean (±SD) %EWL from prebanding was 86.8±10.1%. Revisional LSG resulted in a further median %EWL of 28.0% (range, 7.9%-68.9%) versus weight at time of band removal. Revisional LSG after band erosion was found to be feasible and effective. However, it is prone to severe complication. In selected cases of band erosion, LSG can be performed at the time of band removal in a single stage.

Erosion problems in Alexandroupolis coastline, North-Eastern Greece

NASA Astrophysics Data System (ADS)

Xeidakis, G. S.; Delimani, P.; Skias, S.

2007-12-01

This paper deals with the coastal erosion processes and the related problems around the city of Alexandroupolis, NE Aegean Sea, N. Greece. The area is very fast developing, as the city is an important port and a summer resort center in SE Balkans, and will become soon a transportation and energy center, as well. The coastline under study exhibits an east west orientation and has a length of more than 50 km. The spatial distribution and the characteristics of the changes in the shoreline were studied by comparing old and new air photographs and topographic maps, as well as through repeated series of field observations and local measurements regarding the erosion process. From these studies it was concluded that the greater stretch of the western part of the coast, under consideration, is of moderate to high relief, with a considerable participation of coastal cliffs. It consists of conglomerates of varying granulometry and consistency and is under moderate to severe erosion process. The erosion phenomena in the western part of the coast may be attributed, primarily, to strong S, SW winds, blowing in the area and to trapping of sediments by Alexandroupolis’ port breakwaters; the port stops or/and diverts the sediments to the open sea; and to the east to west longshore sea current, prevailing in the area. The eastern stretch of the coast is a plain area, formed by sandy silty sediments; being a part of the river Evros’ Delta, it is under deposition and accretes seawards. The majority of the coasts under consideration are classified as coasts of high wave energy potential. Hard structures, as shore protection measures, have been constructed in some places, but they were proved, in rather short time-period, ineffective and suffered extensive failures. Thus, it is argued that for a long-term cost-effective tackling of the various erosion problems on any stretch, priority must be given to soft engineering measures; although, certain hard measures, carefully selected and locally implemented, can contribute to forming a rational combination of protection/mitigation measures. Besides, the development pressures in the coastal zone have to be confronted, in a sustainable way, through new integrated coast management regulations.

Analysis of spatio-temporal variability of C-factor derived from remote sensing data

NASA Astrophysics Data System (ADS)

Pechanec, Vilem; Benc, Antonin; Purkyt, Jan; Cudlin, Pavel

2016-04-01

In some risk areas water erosion as the present task has got the strong influence on agriculture and can threaten inhabitants. In our country combination of USLE and RUSLE models has been used for water erosion assessment (Krása et al., 2013). Role of vegetation cover is characterized by the help of vegetation protection factor, so-called C- factor. Value of C-factor is given by the ratio of washing-off on a plot with arable crops to standard plot which is kept as fallow regularly spud after any rain (Janeček et al., 2012). Under conditions we cannot identify crop structure and its turn, determination of C-factor can be problem in large areas. In such case we only determine C-factor according to the average crop representation. New technologies open possibilities for acceleration and specification of the approach. Present-day approach for the C-factor determination is based on the analysis of multispectral image data. Red and infrared spectrum is extracted and these parts of image are used for computation of vegetation index series (NDVI, TSAVI). Acquired values for fractional time sections (during vegetation period) are averaged out. At the same time values of vegetation indices for a forest and cleared area are determined. Also regressive coefficients are computed. Final calculation is done by the help of regressive equations expressing relation between values of NDVI and C-factor (De Jong, 1994; Van der Knijff, 1999; Karaburun, 2010). Up-to-date land use layer is used for the determination of erosion threatened areas on the base of selection of individual landscape segments of erosion susceptible categories of land use. By means of Landsat 7 data C-factor has been determined for the whole area of the Czech Republic in every month of the year of 2014. At the model area in a small watershed C-factor has been determined by the conventional (tabular) procedure. Analysis was focused on: i) variability assessment of C-factor values while using the conventional procedure and remote sensing, ii) variability assessment of values in different months for selected crops - time variability, growth dynamics and vegetation cover have been taken into account; iii) evaluation of space variability of C-factor values for selected crops - variability of natural conditions, markedly influencing vegetation fitness, has been taken into account. Described methods can be used for the planning of agricultural activities and for the proposing of full-scale land replotting. Presently these activities have been financially supported by the European Structural and Investment Funds.