27 CFR 20.94 - Statement of process.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 5150.19 shall also contain the following information: (i) Flow diagrams shall be submitted with the... connecting pipelines and valves. All major equipment shall be identified as to its use. The direction of flow through the pipelines shall be indicated in the flow diagram. The flow diagram, shall be accompanied by a...

Automated Methodologies for the Design of Flow Diagrams for Development and Maintenance Activities

NASA Astrophysics Data System (ADS)

Shivanand M., Handigund; Shweta, Bhat

The Software Requirements Specification (SRS) of the organization is a text document prepared by strategic management incorporating the requirements of the organization. These requirements of ongoing business/ project development process involve the software tools, the hardware devices, the manual procedures, the application programs and the communication commands. These components are appropriately ordered for achieving the mission of the concerned process both in the project development and the ongoing business processes, in different flow diagrams viz. activity chart, workflow diagram, activity diagram, component diagram and deployment diagram. This paper proposes two generic, automatic methodologies for the design of various flow diagrams of (i) project development activities, (ii) ongoing business process. The methodologies also resolve the ensuing deadlocks in the flow diagrams and determine the critical paths for the activity chart. Though both methodologies are independent, each complements other in authenticating its correctness and completeness.

Velocity diagrams

NASA Technical Reports Server (NTRS)

Whitney, W. J.; Stewart, W. L.

1972-01-01

The selection and design of velocity diagrams for axial flow turbines are considered. Application is treated in two parts which includes: (1) mean-section diagrams, and (2) radial variation of diagrams. In the first part, the velocity diagrams occurring at the mean section are assumed to represent the average conditions encountered by the turbine. The different types of diagrams, their relation to stage efficiency, and their selection when staging is required are discussed. In the second part, it is shown that in certain cases the mean-section diagrams may or may not represent the average flow conditions for the entire blade span. In the case of relatively low hub- to tip-radius ratios, substantial variations in the velocity diagrams are encountered. The radial variations in flow conditions and their effect on the velocity diagrams are considered.

CACDA Jiffy War Game Programmers Manual

DTIC Science & Technology

1977-03-01

variables for INDEX5. F-12 F-4. Program variables for LOSS. F-14 F-5. Program variables for DISPLAY. F- 16 G-I. Program variables for OVLY 1 (ROFA). G...variables for FASCAM. J-9 K-1. Program variables for OVLY 5 (AHAD). K-2 L-i. Program variables for CANNON. L-2 L-2. Program variables for CLGP. L- 16 M-i...flow diagram. 56 13. TANK (OVLY 2) flow diagram. 62 14. INFANT (OVLY 3) flow diagram. 69 15. MINE flow diagram. 74 16 . Subroutine FASCAM flow

Feedback systems for nontraditional medicines: a case for the signal flow diagram.

PubMed

Tice, B S

1998-11-01

The signal flow diagram is a graphic method used to represent complex data that is found in the field of biology and hence the field of medicine. The signal flow diagram is analyzed against a table of data and a flow chart of data and evaluated on the clarity and simplicity of imparting this information. The data modeled is from previous clinical studies and nontraditional medicine from Africa, China, and South America. This report is a development from previous presentations of the signal flow diagram.1-4

18 CFR 157.14 - Exhibits.

Code of Federal Regulations, 2013 CFR

2013-04-01

...) Exhibit G—Flow diagrams showing daily design capacity and reflecting operation with and without proposed facilities added. A flow diagram showing daily design capacity and reflecting operating conditions with only existing facilities in operation. A second flow diagram showing daily design capacity and reflecting...

18 CFR 157.14 - Exhibits.

Code of Federal Regulations, 2012 CFR

2012-04-01

...) Exhibit G—Flow diagrams showing daily design capacity and reflecting operation with and without proposed facilities added. A flow diagram showing daily design capacity and reflecting operating conditions with only existing facilities in operation. A second flow diagram showing daily design capacity and reflecting...

18 CFR 157.14 - Exhibits.

Code of Federal Regulations, 2010 CFR

2010-04-01

...) Exhibit G—Flow diagrams showing daily design capacity and reflecting operation with and without proposed facilities added. A flow diagram showing daily design capacity and reflecting operating conditions with only existing facilities in operation. A second flow diagram showing daily design capacity and reflecting...

18 CFR 157.14 - Exhibits.

Code of Federal Regulations, 2011 CFR

2011-04-01

...) Exhibit G—Flow diagrams showing daily design capacity and reflecting operation with and without proposed facilities added. A flow diagram showing daily design capacity and reflecting operating conditions with only existing facilities in operation. A second flow diagram showing daily design capacity and reflecting...

18 CFR 157.14 - Exhibits.

Code of Federal Regulations, 2014 CFR

2014-04-01

...) Exhibit G—Flow diagrams showing daily design capacity and reflecting operation with and without proposed facilities added. A flow diagram showing daily design capacity and reflecting operating conditions with only existing facilities in operation. A second flow diagram showing daily design capacity and reflecting...

Correlated sequential tunneling through a double barrier for interacting one-dimensional electrons

NASA Astrophysics Data System (ADS)

Thorwart, M.; Egger, R.; Grifoni, M.

2005-07-01

The problem of resonant tunneling through a quantum dot weakly coupled to spinless Tomonaga-Luttinger liquids has been studied. We compute the linear conductance due to sequential tunneling processes upon employing a master equation approach. Besides the previously used lowest-order golden rule rates describing uncorrelated sequential tunneling processes, we systematically include higher-order correlated sequential tunneling (CST) diagrams within the standard Weisskopf-Wigner approximation. We provide estimates for the parameter regions where CST effects can be important. Focusing mainly on the temperature dependence of the peak conductance, we discuss the relation of these findings to previous theoretical and experimental results.

Correlated sequential tunneling in Tomonaga-Luttinger liquid quantum dots

NASA Astrophysics Data System (ADS)

Thorwart, M.; Egger, R.; Grifoni, M.

2005-02-01

We investigate tunneling through a quantum dot formed by two strong impurites in a spinless Tomonaga-Luttinger liquid. Upon employing a Markovian master equation approach, we compute the linear conductance due to sequential tunneling processes. Besides the previously used lowest-order Golden Rule rates describing uncorrelated sequential tunneling (UST) processes, we systematically include higher-order correlated sequential tunneling (CST) diagrams within the standard Weisskopf-Wigner approximation. We provide estimates for the parameter regions where CST effects are shown to dominate over UST. Focusing mainly on the temperature dependence of the conductance maximum, we discuss the relation of our results to previous theoretical and experimental results.

Finding False Paths in Sequential Circuits

NASA Astrophysics Data System (ADS)

Matrosova, A. Yu.; Andreeva, V. V.; Chernyshov, S. V.; Rozhkova, S. V.; Kudin, D. V.

2018-02-01

Method of finding false paths in sequential circuits is developed. In contrast with heuristic approaches currently used abroad, the precise method based on applying operations on Reduced Ordered Binary Decision Diagrams (ROBDDs) extracted from the combinational part of a sequential controlling logic circuit is suggested. The method allows finding false paths when transfer sequence length is not more than the given value and obviates the necessity of investigation of combinational circuit equivalents of the given lengths. The possibilities of using of the developed method for more complicated circuits are discussed.

Teaching Verbal Chains Using Flow Diagrams and Texts

ERIC Educational Resources Information Center

Holliday, William G.

1976-01-01

A discussion of the recent diagram and attention theory and research surprisingly suggests that a single flow diagram with instructive questions constitutes an effective learning medium in terms of verbal chaining. (Author)

CADDIS Volume 2. Sources, Stressors and Responses: Flow Alteration - Simple Conceptual Diagram

EPA Pesticide Factsheets

Introduction to the flow alteration module, when to list flow alteration as a candidate cause, ways to measure flow alteration, simple and detailed conceptual model diagrams for flow alteration, flow alteration module references and literature reviews.

CADDIS Volume 2. Sources, Stressors and Responses: Flow Alteration - Detailed Conceptual Diagram

EPA Pesticide Factsheets

Introduction to the flow alteration module, when to list flow alteration as a candidate cause, ways to measure flow alteration, simple and detailed conceptual model diagrams for flow alteration, flow alteration module references and literature reviews.

Formulae and Flow-Diagrams

ERIC Educational Resources Information Center

Willson, William Wynne

1977-01-01

The author recommends the use of flow charting to help students understand the manipulation of algebraic formulae. He identifies some problems with flow charts and suggests an alternative method of constructing flow diagrams. (SD)

40 CFR 60.103a - Design, equipment, work practice or operational standards.

Code of Federal Regulations, 2014 CFR

2014-07-01

...) Description and simple process flow diagram showing the interconnection of the following components of the... rate. (iv) Description and simple process flow diagram showing all gas lines (including flare, purge... which lines are monitored and identify on the process flow diagram the location and type of each monitor...

40 CFR 60.103a - Design, equipment, work practice or operational standards.

Code of Federal Regulations, 2013 CFR

2013-07-01

...) Description and simple process flow diagram showing the interconnection of the following components of the... rate. (iv) Description and simple process flow diagram showing all gas lines (including flare, purge... which lines are monitored and identify on the process flow diagram the location and type of each monitor...

The Effect of Conceptual Diagrams on Aviation Mechanics' Technical Systems Understanding.

ERIC Educational Resources Information Center

Satchwell, Richard E.; Johnson, Scott D.

A quasi-experimental study explored the effect of functional flow diagrams on technical system understanding. An individualized field training package which contained schematic diagrams that illustrated an aircraft's electrical system was complimented with functional flow diagrams. In a 4-week treatment, a control group of 10 students enrolled in…

A novel diagram and complement to the CONSORT chart for presenting multimodal clinical trials.

PubMed

Schuller, Jan C; Mayer, Michael; Lanz, Doris; Schmitz, Shu-Fang Hsu; Brauchli, Peter; Leupin, Nicolas

2009-05-01

We developed a novel diagram to depict patient flow and outcomes in clinical trials. In contrast to flow diagrams such as the CONSORT chart, our diagram enables individual patient histories to be traced and depicts important patterns of treatment administration and outcomes, such as response and adverse events. Also, it is particularly useful for multimodal treatments or a sequence of different therapies where the CONSORT flow chart is less informative and can be confusing.

7 CFR 42.123 - Flow diagram for skip lot sampling and inspection.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 7 Agriculture 2 2014-01-01 2014-01-01 false Flow diagram for skip lot sampling and inspection. 42.123 Section 42.123 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING... Procedures § 42.123 Flow diagram for skip lot sampling and inspection. EC02SE91.000 Notes: 1. Only normal...

7 CFR 42.123 - Flow diagram for skip lot sampling and inspection.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 2 2011-01-01 2011-01-01 false Flow diagram for skip lot sampling and inspection. 42.123 Section 42.123 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING... Procedures § 42.123 Flow diagram for skip lot sampling and inspection. EC02SE91.000 Notes: 1. Only normal...

7 CFR 42.123 - Flow diagram for skip lot sampling and inspection.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 2 2013-01-01 2013-01-01 false Flow diagram for skip lot sampling and inspection. 42.123 Section 42.123 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING... Procedures § 42.123 Flow diagram for skip lot sampling and inspection. EC02SE91.000 Notes: 1. Only normal...

7 CFR 42.123 - Flow diagram for skip lot sampling and inspection.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 7 Agriculture 2 2012-01-01 2012-01-01 false Flow diagram for skip lot sampling and inspection. 42.123 Section 42.123 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING... Procedures § 42.123 Flow diagram for skip lot sampling and inspection. EC02SE91.000 Notes: 1. Only normal...

Reporting of participant flow diagrams in published reports of randomized trials.

PubMed

Hopewell, Sally; Hirst, Allison; Collins, Gary S; Mallett, Sue; Yu, Ly-Mee; Altman, Douglas G

2011-12-05

Reporting of the flow of participants through each stage of a randomized trial is essential to assess the generalisability and validity of its results. We assessed the type and completeness of information reported in CONSORT (Consolidated Standards of Reporting Trials) flow diagrams published in current reports of randomized trials. A cross sectional review of all primary reports of randomized trials which included a CONSORT flow diagram indexed in PubMed core clinical journals (2009). We assessed the proportion of parallel group trial publications reporting specific items recommended by CONSORT for inclusion in a flow diagram. Of 469 primary reports of randomized trials, 263 (56%) included a CONSORT flow diagram of which 89% (237/263) were published in a CONSORT endorsing journal. Reports published in CONSORT endorsing journals were more likely to include a flow diagram (62%; 237/380 versus 29%; 26/89). Ninety percent (236/263) of reports which included a flow diagram had a parallel group design, of which 49% (116/236) evaluated drug interventions, 58% (137/236) were multicentre, and 79% (187/236) compared two study groups, with a median sample size of 213 participants. Eighty-one percent (191/236) reported the overall number of participants assessed for eligibility, 71% (168/236) the number excluded prior to randomization and 98% (231/236) the overall number randomized. Reasons for exclusion prior to randomization were more poorly reported. Ninety-four percent (223/236) reported the number of participants allocated to each arm of the trial. However, only 40% (95/236) reported the number who actually received the allocated intervention, 67% (158/236) the number lost to follow up in each arm of the trial, 61% (145/236) whether participants discontinued the intervention during the trial and 54% (128/236) the number included in the main analysis. Over half of published reports of randomized trials included a diagram showing the flow of participants through the trial. However, information was often missing from published flow diagrams, even in articles published in CONSORT endorsing journals. If important information is not reported it can be difficult and sometimes impossible to know if the conclusions of that trial are justified by the data presented.

Fluctuation diagrams for hot-wire anemometry in subsonic compressible flows

NASA Technical Reports Server (NTRS)

Stainback, P. C.; Nagabushana, K. A.

1991-01-01

The concept of using 'fluctuation diagrams' for describing basic fluctuations in compressible flows was reported by Kovasznay in the 1950's. The application of this technique, for the most part, was restricted to supersonic flows. Recently, Zinovev and Lebiga published reports where they considered the fluctuation diagrams in subsonic compressible flows. For the above studies, the velocity and density sensitivities of the heated wires were equal. However, there are considerable data, much taken in the 1950's, which indicate that under some conditions the velocity and density sensitivities are not equal in subsonic compressible flows. Therefore, possible fluctuation diagrams are described for the cases where the velocity and density sensitivities are equal and the more general cases where they are unequal.

Knowledge Representation and Communication: Imparting Current State Information Flow to CPR Stakeholders

PubMed Central

de la Cruz, Norberto B.; Spiece, Leslie J.

2000-01-01

Understanding and communicating the who, what, where, when, why, and how of the clinics and services for which the computerized patient record (CPR) will be built is an integral part of the implementation process. Formal methodologies have been developed to diagram information flow -- flow charts, state-transition diagram (STDs), data flow diagrams (DFDs). For documentation of the processes at our ambulatory CPR pilot site, flowcharting was selected as the preferred method based upon its versatility and understandability.

Issues to be Considered in the Evaluation of Technical Proposals from the Ada (Trademark) Language Perspective.

DTIC Science & Technology

1985-06-10

flowcharts - hierarchical charts - data flow diagrams - finite state diagrams - control flow diagrams - decision tables/trees - entity-relationship...and beginners ; for example, is prompting via menus provided for beginners and single keystroke capability provided for experienced users? 2-13 - input

77 FR 11520 - Commission Information Collection Activities; Comment Request; Extension

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-27

..., Gas Pipeline Certificates: Annual Reports of System Flow Diagrams and System Capacity. DATES: Comments... Certificates: Annual Reports of System Flow Diagrams and System Capacity. OMB Control No.: 1902-0005. Type of... June 1 of each year, diagrams reflecting operating conditions on the pipeline's main transmission...

The application of intraoperative transit time flow measurement to accurately assess anastomotic quality in sequential vein grafting

PubMed Central

Yu, Yang; Zhang, Fan; Gao, Ming-Xin; Li, Hai-Tao; Li, Jing-Xing; Song, Wei; Huang, Xin-Sheng; Gu, Cheng-Xiong

2013-01-01

OBJECTIVES Intraoperative transit time flow measurement (TTFM) is widely used to assess anastomotic quality in coronary artery bypass grafting (CABG). However, in sequential vein grafting, the flow characteristics collected by the conventional TTFM method are usually associated with total graft flow and might not accurately indicate the quality of every distal anastomosis in a sequential graft. The purpose of our study was to examine a new TTFM method that could assess the quality of each distal anastomosis in a sequential graft more reliably than the conventional TTFM approach. METHODS Two TTFM methods were tested in 84 patients who underwent sequential saphenous off-pump CABG in Beijing An Zhen Hospital between April and August 2012. In the conventional TTFM method, normal blood flow in the sequential graft was maintained during the measurement, and the flow probe was placed a few centimetres above the anastomosis to be evaluated. In the new method, blood flow in the sequential graft was temporarily reduced during the measurement by placing an atraumatic bulldog clamp at the graft a few centimetres distal to the anastomosis to be evaluated, while the position of the flow probe remained the same as in the conventional method. This new TTFM method was named the flow reduction TTFM. Graft flow parameters measured by both methods were compared. RESULTS Compared with the conventional TTFM, the flow reduction TTFM resulted in significantly lower mean graft blood flow (P < 0.05); in contrast, yielded significantly higher pulsatility index (P < 0.05). Diastolic filling was not significantly different between the two methods and was >50% in both cases. Interestingly, the flow reduction TTFM identified two defective middle distal anastomoses that the conventional TTFM failed to detect. Graft flows near the defective distal anastomoses were improved substantially after revision. CONCLUSIONS In this study, we found that temporary reduction of graft flow during TTFM seemed to enhance the sensitivity of TTFM to less-than-critical anastomotic defects in a sequential graft and to improve the overall accuracy of the intraoperative assessment of anastomotic quality in sequential vein grafting. PMID:24000314

Reporting of participant flow diagrams in published reports of randomized trials

PubMed Central

2011-01-01

Background Reporting of the flow of participants through each stage of a randomized trial is essential to assess the generalisability and validity of its results. We assessed the type and completeness of information reported in CONSORT (Consolidated Standards of Reporting Trials) flow diagrams published in current reports of randomized trials. Methods A cross sectional review of all primary reports of randomized trials which included a CONSORT flow diagram indexed in PubMed core clinical journals (2009). We assessed the proportion of parallel group trial publications reporting specific items recommended by CONSORT for inclusion in a flow diagram. Results Of 469 primary reports of randomized trials, 263 (56%) included a CONSORT flow diagram of which 89% (237/263) were published in a CONSORT endorsing journal. Reports published in CONSORT endorsing journals were more likely to include a flow diagram (62%; 237/380 versus 29%; 26/89). Ninety percent (236/263) of reports which included a flow diagram had a parallel group design, of which 49% (116/236) evaluated drug interventions, 58% (137/236) were multicentre, and 79% (187/236) compared two study groups, with a median sample size of 213 participants. Eighty-one percent (191/236) reported the overall number of participants assessed for eligibility, 71% (168/236) the number excluded prior to randomization and 98% (231/236) the overall number randomized. Reasons for exclusion prior to randomization were more poorly reported. Ninety-four percent (223/236) reported the number of participants allocated to each arm of the trial. However, only 40% (95/236) reported the number who actually received the allocated intervention, 67% (158/236) the number lost to follow up in each arm of the trial, 61% (145/236) whether participants discontinued the intervention during the trial and 54% (128/236) the number included in the main analysis. Conclusions Over half of published reports of randomized trials included a diagram showing the flow of participants through the trial. However, information was often missing from published flow diagrams, even in articles published in CONSORT endorsing journals. If important information is not reported it can be difficult and sometimes impossible to know if the conclusions of that trial are justified by the data presented. PMID:22141446

21 CFR 862.2150 - Continuous flow sequential multiple chemistry analyzer for clinical use.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Continuous flow sequential multiple chemistry..., DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES CLINICAL CHEMISTRY AND CLINICAL TOXICOLOGY DEVICES Clinical Laboratory Instruments § 862.2150 Continuous flow sequential multiple chemistry...

21 CFR 862.2150 - Continuous flow sequential multiple chemistry analyzer for clinical use.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Continuous flow sequential multiple chemistry..., DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES CLINICAL CHEMISTRY AND CLINICAL TOXICOLOGY DEVICES Clinical Laboratory Instruments § 862.2150 Continuous flow sequential multiple chemistry...

21 CFR 862.2150 - Continuous flow sequential multiple chemistry analyzer for clinical use.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Continuous flow sequential multiple chemistry..., DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES CLINICAL CHEMISTRY AND CLINICAL TOXICOLOGY DEVICES Clinical Laboratory Instruments § 862.2150 Continuous flow sequential multiple chemistry...

21 CFR 862.2150 - Continuous flow sequential multiple chemistry analyzer for clinical use.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Continuous flow sequential multiple chemistry..., DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES CLINICAL CHEMISTRY AND CLINICAL TOXICOLOGY DEVICES Clinical Laboratory Instruments § 862.2150 Continuous flow sequential multiple chemistry...

21 CFR 862.2150 - Continuous flow sequential multiple chemistry analyzer for clinical use.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Continuous flow sequential multiple chemistry..., DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES CLINICAL CHEMISTRY AND CLINICAL TOXICOLOGY DEVICES Clinical Laboratory Instruments § 862.2150 Continuous flow sequential multiple chemistry...

MotionFlow: Visual Abstraction and Aggregation of Sequential Patterns in Human Motion Tracking Data.

PubMed

Jang, Sujin; Elmqvist, Niklas; Ramani, Karthik

2016-01-01

Pattern analysis of human motions, which is useful in many research areas, requires understanding and comparison of different styles of motion patterns. However, working with human motion tracking data to support such analysis poses great challenges. In this paper, we propose MotionFlow, a visual analytics system that provides an effective overview of various motion patterns based on an interactive flow visualization. This visualization formulates a motion sequence as transitions between static poses, and aggregates these sequences into a tree diagram to construct a set of motion patterns. The system also allows the users to directly reflect the context of data and their perception of pose similarities in generating representative pose states. We provide local and global controls over the partition-based clustering process. To support the users in organizing unstructured motion data into pattern groups, we designed a set of interactions that enables searching for similar motion sequences from the data, detailed exploration of data subsets, and creating and modifying the group of motion patterns. To evaluate the usability of MotionFlow, we conducted a user study with six researchers with expertise in gesture-based interaction design. They used MotionFlow to explore and organize unstructured motion tracking data. Results show that the researchers were able to easily learn how to use MotionFlow, and the system effectively supported their pattern analysis activities, including leveraging their perception and domain knowledge.

Concepts of diffusion theory and a graphic approach to the description of the epidemic flow of contagious disease.

PubMed Central

Angulo, J J; Pederneiras, C A; Ebner, W; Kimura, E M; Megale, P

1980-01-01

Concepts used to analyze sociological, geographic, and economic processes were adapted to an examination of the diffusion of contagious disease. The example used in applying these concepts was an epidemic of variola minor which continued for 12 months in an area of 1,006 square kilometers centered on the city of Bragança Paulista, Sao Paulo State (Brazil). A graphic procedure is proposed that depicts aspects of the epidemic flow of person-to-person transmission. Spatial, temporal, and sociological characteristics of the epidemic flow are disclosed in sequential diagrams. They represent geographic areas as well as schools and agglomerates of households affected by the epidemic at a given time, the mode of diffusion, and the source of the infection. The procedure yielded indirect evidence of the role of school pupils as introducers of variola minor into households and school classes. All subdivisions of the city, six of the seven rural districts, and four of the five elementary schools were affected through hierarchical (between-areas) diffusion. Subsequently, there was neighborhood (within-area) diffusion, and this resulted in new interactions between areas. PMID:7422812

Spent Nuclear Fuel (SNF) Project Canister Storage Building (CSB) Process Flow Diagram Mass Balance Calculations

DOE Office of Scientific and Technical Information (OSTI.GOV)

KLEM, M.J.

2000-05-11

The purpose of these calculations is to develop the material balances for documentation of the Canister Storage Building (CSB) Process Flow Diagram (PFD) and future reference. The attached mass balances were prepared to support revision two of the PFD for the CSB. The calculations refer to diagram H-2-825869.

An algorithmic approach to the brain biopsy--part I.

PubMed

Kleinschmidt-DeMasters, B K; Prayson, Richard A

2006-11-01

The formulation of appropriate differential diagnoses for a slide is essential to the practice of surgical pathology but can be particularly challenging for residents and fellows. Algorithmic flow charts can help the less experienced pathologist to systematically consider all possible choices and eliminate incorrect diagnoses. They can assist pathologists-in-training in developing orderly, sequential, and logical thinking skills when confronting difficult cases. To present an algorithmic flow chart as an approach to formulating differential diagnoses for lesions seen in surgical neuropathology. An algorithmic flow chart to be used in teaching residents. Algorithms are not intended to be final diagnostic answers on any given case. Algorithms do not substitute for training received from experienced mentors nor do they substitute for comprehensive reading by trainees of reference textbooks. Algorithmic flow diagrams can, however, direct the viewer to the correct spot in reference texts for further in-depth reading once they hone down their diagnostic choices to a smaller number of entities. The best feature of algorithms is that they remind the user to consider all possibilities on each case, even if they can be quickly eliminated from further consideration. In Part I, we assist the resident in learning how to handle brain biopsies in general and how to distinguish nonneoplastic lesions that mimic tumors from true neoplasms.

An algorithmic approach to the brain biopsy--part II.

PubMed

Prayson, Richard A; Kleinschmidt-DeMasters, B K

2006-11-01

The formulation of appropriate differential diagnoses for a slide is essential to the practice of surgical pathology but can be particularly challenging for residents and fellows. Algorithmic flow charts can help the less experienced pathologist to systematically consider all possible choices and eliminate incorrect diagnoses. They can assist pathologists-in-training in developing orderly, sequential, and logical thinking skills when confronting difficult cases. To present an algorithmic flow chart as an approach to formulating differential diagnoses for lesions seen in surgical neuropathology. An algorithmic flow chart to be used in teaching residents. Algorithms are not intended to be final diagnostic answers on any given case. Algorithms do not substitute for training received from experienced mentors nor do they substitute for comprehensive reading by trainees of reference textbooks. Algorithmic flow diagrams can, however, direct the viewer to the correct spot in reference texts for further in-depth reading once they hone down their diagnostic choices to a smaller number of entities. The best feature of algorithms is that they remind the user to consider all possibilities on each case, even if they can be quickly eliminated from further consideration. In Part II, we assist the resident in arriving at the correct diagnosis for neuropathologic lesions containing granulomatous inflammation, macrophages, or abnormal blood vessels.

54. PHOTOCOPY OF DRAWING AMMONIA LEACHING PLANT FLOW DIAGRAM, REPRESENTING ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

54. PHOTOCOPY OF DRAWING AMMONIA LEACHING PLANT FLOW DIAGRAM, REPRESENTING ONE COMPLETE CYCLE - Kennecott Copper Corporation, On Copper River & Northwestern Railroad, Kennicott, Valdez-Cordova Census Area, AK

53. PHOTOCOPY OF DRAWING AMMONIA LEACHING PLANT FLOW DIAGRAM, REPRESENTING ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

53. PHOTOCOPY OF DRAWING AMMONIA LEACHING PLANT FLOW DIAGRAM, REPRESENTING ONE COMPLETE CYCLE - Kennecott Copper Corporation, On Copper River & Northwestern Railroad, Kennicott, Valdez-Cordova Census Area, AK

55. PHOTOCOPY OF DRAWING AMMONIA LEACHING PLANT FLOW DIAGRAM, REPRESENTING ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

55. PHOTOCOPY OF DRAWING AMMONIA LEACHING PLANT FLOW DIAGRAM, REPRESENTING ONE COMPLETE CYCLE - Kennecott Copper Corporation, On Copper River & Northwestern Railroad, Kennicott, Valdez-Cordova Census Area, AK

Making Data Flow Diagrams Accessible for Visually Impaired Students Using Excel Tables

ERIC Educational Resources Information Center

Sauter, Vicki L.

2015-01-01

This paper addresses the use of Excel tables to convey information to blind students that would otherwise be presented using graphical tools, such as Data Flow Diagrams. These tables can supplement diagrams in the classroom when introducing their use to understand the scope of a system and its main sub-processes, on exams when answering questions…

Infiltration Processes and Flow Velocities Across the Landscape: When and Where is Macropore Flow Relevant?

NASA Astrophysics Data System (ADS)

Demand, D.; Blume, T.; Weiler, M.

2017-12-01

Preferential flow in macropores significantly affects the distributions of water and solutes in soil and many studies showed its relevance worldwide. Although some models include this process as a second pore domain, little is known about the spatial patterns and temporal dynamics. For example, while flow in the matrix is usually modeled and parameterized based on soil texture, an influence of texture on non-capillary flow for a given land-use class is poorly understood. To investigate the temporal and spatial dynamics on preferential flow we used a four-year soil moisture dataset from the mesoscale Attert catchment (288 km²) in Luxembourg. This dataset contains time series from 126 soil profiles in different textures and two land-use classes (forest, grassland). The soil moisture probes were installed in 10, 30 and 50 cm depth and measured in a 5-minute temporal resolution. Events were defined by a soil moisture increase higher than the instrument noise after a precipitation sum of more than 1 mm. Precipitation was measured next to the profiles so that each location could be associated to its unique precipitation characteristics. For every event and profile the soil moisture reaction was classified in sequential (ordered by depth) and non-sequential response. A non-sequential soil moisture reaction was used as an indicator of preferential flow. For sequential flow, the velocity was determined by the first reaction between two vertically adjacent sensors. The sensor reaction and wetting front velocity was analyzed in the context of precipitation characteristics and initial soil water content. Grassland sites showed a lower proportion of non-sequential flow than forest sites. For forest, non-sequential response is dependent on texture, rainfall intensity and initial water content. This is less distinct for the grassland sites. Furthermore, sequential reactions show higher flow velocities at sites, which also have high percentage of non-sequential response. In contrast, grassland sites show a more homogenous wetting front independent of soil texture. Compared against common modelling approaches of soil water flow, measured velocities show clear evidence of preferential flow, especially for forest soils. The analysis also shows that vegetation can alter the soil properties above the textural properties alone.

[Effect of hemorheology on ultrasonic doppler blood flow spectrum diagram].

PubMed

Zhang, Shenghua; Qin, Renjia

2014-08-01

The present research aims to point out the long-existing defect of analyzing the spectrum diagram only from the perspective of haemodynamics instead of haemorheology. In the light of the theories of haemodynamics and haemorheology, the causes of spectrum diagram formation of carotid artery blood at the rapid and slow flow can be clarified completely and accurately. Four conclusions have been drawn in the end. As long as the velocity gradient is large enough, obvious red blood cells concentrate to the shaft even in the big or bigger blood vessels; the spectrum diagram is the powerful proof of the two phase flow model of blood; the spectrum diagram can be completely and accurately analyzed only by combining haemodynamics with haemorheology; and only when the red blood cells concentrate to the shaft, the big or bigger blood vessels can be regarded as haemogeneous fluid.

Theoretical flow regime diagrams for the AGCE

NASA Technical Reports Server (NTRS)

Fowlis, W. W.; Miller, T. L.; Roberts, G. O.; Kopecky, K. J.

1984-01-01

The major criterion for the design of the Atmospheric General Circulation Experiment is that it be possible to realize strong baroclinic instability in the apparatus. A spherical annulus configuration which allows only steady basic state flows was chosen for the first set of stability analyses. Baroclinic instability was found for this configuration and few results suggest a regime diagram very different from the cylindrical annulus regime diagram.

Do health technology assessments comply with QUOROM diagram guidance? An empirical study.

PubMed

Hind, Daniel; Booth, Andrew

2007-11-20

The Quality of Reporting of Meta-analyses (QUOROM) statement provides guidance for improving the quality of reporting of systematic reviews and meta-analyses. To make the process of study selection transparent it recommends "a flow diagram providing information about the number of RCTs identified, included, and excluded and the reasons for excluding them". We undertook an empirical study to identify the extent of compliance in the UK Health Technology Assessment (HTA) programme. We searched Medline to retrieve all systematic reviews of therapeutic interventions in the HTA monograph series published from 2001 to 2005. Two researchers recorded whether each study contained a meta-analysis of controlled trials, whether a QUOROM flow diagram was presented and, if so, whether it expressed the relationship between the number of citations and the number of studies. We used Cohen's kappa to test inter-rater reliability. 87 systematic reviews were retrieved. There was good and excellent inter-rater reliability for, respectively, whether a review contained a meta-analysis and whether each diagram contained a citation-to-study relationship. 49% of systematic reviews used a study selection flow diagram. When only systematic reviews containing a meta-analysis were analysed, compliance was only 32%. Only 20 studies (23% of all systematic reviews; 43% of those having a study selection diagram) had a diagram which expressed the relationship between citations and studies. Compliance with the recommendations of the QUOROM statement is not universal in systematic reviews or meta-analyses. Flow diagrams make the conduct of study selection transparent only if the relationship between citations and studies is clearly expressed. Reviewers should understand what they are counting: citations, papers, studies and trials are fundamentally different concepts which should not be confused in a diagram.

Flame Deflector Section, Elevation, Water Supply Flow Diagram, Exploded ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Flame Deflector - Section, Elevation, Water Supply Flow Diagram, Exploded Deflector Manifolds, and Interior Perspective - Marshall Space Flight Center, F-1 Engine Static Test Stand, On Route 565 between Huntsville and Decatur, Huntsville, Madison County, AL

Introducing the Circular Flow Diagram to Business Students

ERIC Educational Resources Information Center

Daraban, Bogdan

2010-01-01

The circular flow of income diagram is a simplified representation of the functioning of a free-market economic system. It illustrates how businesses interact with the other economic participants within the key macroeconomic markets that coordinate the flow of income through the national economy. Therefore, it can provide students of business with…

Software Tool Integrating Data Flow Diagrams and Petri Nets

NASA Technical Reports Server (NTRS)

Thronesbery, Carroll; Tavana, Madjid

2010-01-01

Data Flow Diagram - Petri Net (DFPN) is a software tool for analyzing other software to be developed. The full name of this program reflects its design, which combines the benefit of data-flow diagrams (which are typically favored by software analysts) with the power and precision of Petri-net models, without requiring specialized Petri-net training. (A Petri net is a particular type of directed graph, a description of which would exceed the scope of this article.) DFPN assists a software analyst in drawing and specifying a data-flow diagram, then translates the diagram into a Petri net, then enables graphical tracing of execution paths through the Petri net for verification, by the end user, of the properties of the software to be developed. In comparison with prior means of verifying the properties of software to be developed, DFPN makes verification by the end user more nearly certain, thereby making it easier to identify and correct misconceptions earlier in the development process, when correction is less expensive. After the verification by the end user, DFPN generates a printable system specification in the form of descriptions of processes and data.

Graphic Organizers: Outlets for Your Thoughts.

ERIC Educational Resources Information Center

Ekhaml, Leticia

1998-01-01

Graphs, bars, charts, and diagrams have been used by designers, writers, and scientists to communicate. Now, research suggests that graphic organizers benefit teaching and learning. This article describes graphic organizers: sequential, conceptual, hierarchical, cyclical, Venn, fishbone or Ishikawa, squeeze and stretch, why-why, t-chart, KWL…

Visualizing Practice with Children and Families.

ERIC Educational Resources Information Center

Mattaini, Mark A.

1995-01-01

Argues that graphic images and technologies can be of substantial help to social work practitioners for assessment and intervention with children and families. Suggests a range of graphic tools and techniques, including profiles, ecomaps, sequential ecomaps, contingency diagrams, concurrent graphing, and computerized Visual EcoScan. (DR)

Earth Observing System (EOS)/Advanced Microwave Sounding Unit-A (AMSU-A): Instrument logic diagrams

NASA Technical Reports Server (NTRS)

1994-01-01

This report contains all of the block diagrams and internal logic diagrams for the Earth Observation System Advanced Microwave Sounding Unit-A (AMSU-A). These diagrams show the signal inputs, outputs, and internal signal flow for the AMSU-A.

Flow regimes in a shallow rotating cylindrical annulus with temperature gradients imposed on the horizontal boundaries

NASA Technical Reports Server (NTRS)

Hathaway, D. H.; Fowlis, W. W.

1986-01-01

Experimental flow regime diagrams are determined for a new rotating cylindrical annulus configuration which permits a measure of control over the internal vertical temperature gradient. The new annulus has radial temperature gradients imposed on plane horizontal thermally conducting endwalls (with the cylindrical sidewalls as insulators) and is considered to be more relevant to atmospheric dynamics studies than the classical cylindrical annulus. Observations have revealed that, in addition to the axisymmetric flow and nonaxisymmetric baroclinic wave flow which occur in the classical annulus, two additional nonaxisymmetric flow types occur in the new annulus: boundary-layer thermal convection and deep thermal convection. Flow regime diagrams for three different values of the imposed vertical temperature difference are presented, and explanations for the flow transitions are offered. The new annulus provides scientific backup for the proposed Atmospheric General Circulation Experiment for Spacelab. The apparatus diagram is included.

Rapid granular flows on a rough incline: phase diagram, gas transition, and effects of air drag.

PubMed

Börzsönyi, Tamás; Ecke, Robert E

2006-12-01

We report experiments on the overall phase diagram of granular flows on an incline with emphasis on high inclination angles where the mean layer velocity approaches the terminal velocity of a single particle free falling in air. The granular flow was characterized by measurements of the surface velocity, the average layer height, and the mean density of the layer as functions of the hopper opening, the plane inclination angle, and the downstream distance x of the flow. At high inclination angles the flow does not reach an x -invariant steady state over the length of the inclined plane. For low volume flow rates, a transition was detected between dense and very dilute (gas) flow regimes. We show using a vacuum flow channel that air did not qualitatively change the phase diagram and did not quantitatively modify mean flow velocities of the granular layer except for small changes in the very dilute gaslike phase.

Asymmetrical booster ascent guidance and control system design study. Volume 5: Space shuttle powered explicit guidance. [space shuttle development

NASA Technical Reports Server (NTRS)

Jaggers, R. F.

1974-01-01

An optimum powered explicit guidance algorithm capable of handling all space shuttle exoatospheric maneuvers is presented. The theoretical and practical basis for the currently baselined space shuttle powered flight guidance equations and logic is documented. Detailed flow diagrams for implementing the steering computations for all shuttle phases, including powered return to launch site (RTLS) abort, are also presented. Derivation of the powered RTLS algorithm is provided, as well as detailed flow diagrams for implementing the option. The flow diagrams and equations are compatible with the current powered flight documentation.

30 CFR 250.1910 - What safety and environmental information is required?

Code of Federal Regulations, 2011 CFR

2011-07-01

... information including, as appropriate, a simplified process flow diagram and acceptable upper and lower limits, where applicable, for items such as temperature, pressure, flow and composition; and (3) mechanical design information including, as appropriate, piping and instrument diagrams; electrical area...

30 CFR 250.1910 - What safety and environmental information is required?

Code of Federal Regulations, 2013 CFR

2013-07-01

... appropriate, a simplified process flow diagram and acceptable upper and lower limits, where applicable, for items such as temperature, pressure, flow and composition; and (3) mechanical design information including, as appropriate, piping and instrument diagrams; electrical area classifications; equipment...

40 CFR 420.01 - Applicability.

Code of Federal Regulations, 2011 CFR

2011-07-01

... treatment system including schematic diagrams showing the major treatment system components and flow rates... request for consideration of alternative effluent limitations is to include: (i) A schematic diagram of... waters entering the treatment facility; discharge and recycle flow rates for each water source and each...

40 CFR 60.2025 - What if my chemical recovery unit is not listed in § 60.2020(n)?

Code of Federal Regulations, 2011 CFR

2011-07-01

... materials that are recovered. (3) A description (including a process flow diagram) of the process in which... process. (4) A description (including a process flow diagram) of the chemical constituent recovery process...

40 CFR 420.01 - Applicability.

Code of Federal Regulations, 2013 CFR

2013-07-01

... treatment system including schematic diagrams showing the major treatment system components and flow rates... request for consideration of alternative effluent limitations is to include: (i) A schematic diagram of... waters entering the treatment facility; discharge and recycle flow rates for each water source and each...

40 CFR 60.2025 - What if my chemical recovery unit is not listed in § 60.2020(n)?

Code of Federal Regulations, 2012 CFR

2012-07-01

... materials that are recovered. (3) A description (including a process flow diagram) of the process in which... process. (4) A description (including a process flow diagram) of the chemical constituent recovery process...

40 CFR 60.2025 - What if my chemical recovery unit is not listed in § 60.2020(n)?

Code of Federal Regulations, 2010 CFR

2010-07-01

... materials that are recovered. (3) A description (including a process flow diagram) of the process in which... process. (4) A description (including a process flow diagram) of the chemical constituent recovery process...

40 CFR 420.01 - Applicability.

Code of Federal Regulations, 2012 CFR

2012-07-01

... treatment system including schematic diagrams showing the major treatment system components and flow rates... request for consideration of alternative effluent limitations is to include: (i) A schematic diagram of... waters entering the treatment facility; discharge and recycle flow rates for each water source and each...

30 CFR 250.1910 - What safety and environmental information is required?

Code of Federal Regulations, 2012 CFR

2012-07-01

... appropriate, a simplified process flow diagram and acceptable upper and lower limits, where applicable, for items such as temperature, pressure, flow and composition; and (3) mechanical design information including, as appropriate, piping and instrument diagrams; electrical area classifications; equipment...

30 CFR 250.1910 - What safety and environmental information is required?

Code of Federal Regulations, 2014 CFR

2014-07-01

... appropriate, a simplified process flow diagram and acceptable upper and lower limits, where applicable, for items such as temperature, pressure, flow and composition; and (3) mechanical design information including, as appropriate, piping and instrument diagrams; electrical area classifications; equipment...

40 CFR 60.2558 - What if a chemical recovery unit is not listed in § 60.2555(n)?

Code of Federal Regulations, 2012 CFR

2012-07-01

... materials that are recovered. (3) A description (including a process flow diagram) of the process in which... process. (4) A description (including a process flow diagram) of the chemical constituent recovery process...

40 CFR 420.01 - Applicability.

Code of Federal Regulations, 2014 CFR

2014-07-01

... treatment system including schematic diagrams showing the major treatment system components and flow rates... request for consideration of alternative effluent limitations is to include: (i) A schematic diagram of... waters entering the treatment facility; discharge and recycle flow rates for each water source and each...

Dark energy in six nearby galaxy flows: Synthetic phase diagrams and self-similarity

NASA Astrophysics Data System (ADS)

Chernin, A. D.; Teerikorpi, P.; Dolgachev, V. P.; Kanter, A. A.; Domozhilova, L. M.; Valtonen, M. J.; Byrd, G. G.

2012-09-01

Outward flows of galaxies are observed around groups of galaxies on spatial scales of about 1 Mpc, and around galaxy clusters on scales of 10 Mpc. Using recent data from the Hubble Space Telescope (HST), we have constructed two synthetic velocity-distance phase diagrams: one for four flows on galaxy-group scales and the other for two flows on cluster scales. It has been shown that, in both cases, the antigravity produced by the cosmic dark-energy background is stronger than the gravity produced by the matter in the outflow volume. The antigravity accelerates the flows and introduces a phase attractor that is common to all scales, corresponding to a linear velocity-distance relation (the local Hubble law). As a result, the bundle of outflow trajectories mostly follow the trajectory of the attractor. A comparison of the two diagrams reveals the universal self-similar nature of the outflows: their gross phase structure in dimensionless variables is essentially independent of their physical spatial scales, which differ by approximately a factor of 10 in the two diagrams.

Statechart-based design controllers for FPGA partial reconfiguration

NASA Astrophysics Data System (ADS)

Łabiak, Grzegorz; Wegrzyn, Marek; Rosado Muñoz, Alfredo

2015-09-01

Statechart diagram and UML technique can be a vital part of early conceptual modeling. At the present time there is no much support in hardware design methodologies for reconfiguration features of reprogrammable devices. Authors try to bridge the gap between imprecise UML model and formal HDL description. The key concept in author's proposal is to describe the behavior of the digital controller by statechart diagrams and to map some parts of the behavior into reprogrammable logic by means of group of states which forms sequential automaton. The whole process is illustrated by the example with experimental results.

40 CFR 60.2558 - What if a chemical recovery unit is not listed in § 60.2555(n)?

Code of Federal Regulations, 2010 CFR

2010-07-01

... process flow diagram) of the process in which the materials are burned, highlighting the type, design, and operation of the equipment used in this process. (4) A description (including a process flow diagram) of the...

40 CFR 60.2558 - What if a chemical recovery unit is not listed in § 60.2555(n)?

Code of Federal Regulations, 2011 CFR

2011-07-01

... process flow diagram) of the process in which the materials are burned, highlighting the type, design, and operation of the equipment used in this process. (4) A description (including a process flow diagram) of the...

Differential Cognitive and Affective Responses to Flow Diagrams in Science

ERIC Educational Resources Information Center

Holliday, William G.; And Others

1977-01-01

Describes a study in which tenth-grade biology students who were low verbal performers scored significantly higher on achievement tests when provided with picture-word diagrams of biological concepts than when provided with block-word diagrams. Students and teachers also preferred picture-word diagrams as indicated by a questionnaire. (MLH)

40 CFR 57.203 - Contents of the application.

Code of Federal Regulations, 2014 CFR

2014-07-01

... application shall also contain the following information: (1) A process flow diagram of the smelter, including current process and instrumentation diagrams for all processes or equipment which may emit or affect the... equipment (flow rates, temperature, volumes, compositions, and variations over time); and a list of all...

40 CFR 57.203 - Contents of the application.

Code of Federal Regulations, 2012 CFR

2012-07-01

... application shall also contain the following information: (1) A process flow diagram of the smelter, including current process and instrumentation diagrams for all processes or equipment which may emit or affect the... equipment (flow rates, temperature, volumes, compositions, and variations over time); and a list of all...

40 CFR 57.203 - Contents of the application.

Code of Federal Regulations, 2011 CFR

2011-07-01

... application shall also contain the following information: (1) A process flow diagram of the smelter, including current process and instrumentation diagrams for all processes or equipment which may emit or affect the... equipment (flow rates, temperature, volumes, compositions, and variations over time); and a list of all...

40 CFR 57.203 - Contents of the application.

Code of Federal Regulations, 2013 CFR

2013-07-01

... application shall also contain the following information: (1) A process flow diagram of the smelter, including current process and instrumentation diagrams for all processes or equipment which may emit or affect the... equipment (flow rates, temperature, volumes, compositions, and variations over time); and a list of all...

40. Photograph of a line drawing. 'FLOW DIAGRAM FOR BUILDING ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

40. Photograph of a line drawing. 'FLOW DIAGRAM FOR BUILDING G-1.' Holston Army Ammunition Plant, Holston Defense Corporation. December 1, 1965. Delineator: V. N.J. Drawing # 7651-1007-528. - Holston Army Ammunition Plant, RDX-and-Composition-B Manufacturing Line 9, Kingsport, Sullivan County, TN

Scrutinizing UML Activity Diagrams

NASA Astrophysics Data System (ADS)

Al-Fedaghi, Sabah

Building an information system involves two processes: conceptual modeling of the “real world domain” and designing the software system. Object-oriented methods and languages (e.g., UML) are typically used for describing the software system. For the system analysis process that produces the conceptual description, object-oriented techniques or semantics extensions are utilized. Specifically, UML activity diagrams are the “flow charts” of object-oriented conceptualization tools. This chapter proposes an alternative to UML activity diagrams through the development of a conceptual modeling methodology based on the notion of flow.

Compare Vehicle Technologies | Transportation Research | NREL

Science.gov Websites

electric car diagramming energy storage, power electronics, and climate control components, as well as storage, power electronics, and climate control components, as well as energy flow among components. 3-D control components, as well as energy flow among components. 3-D illustration of electric car diagramming

The Effect of Functional Flow Diagrams on the Technical System Understanding of Apprentice Aircraft Maintenance Mechanics.

ERIC Educational Resources Information Center

Johnson, Scott D.; Satchwell, Richard E.

A quasiexperimental study involved 18 male students enrolled in an aircraft systems course at the University of Illinois. The control group of 10 students studied 39 schematic diagrams of aircraft systems. The treatment group of eight students studied the same schematic diagrams plus conceptual diagrams of the systems. Otherwise, the instruction…

Flow diagram analysis of electrical fatalities in construction industry.

PubMed

Chi, Chia-Fen; Lin, Yuan-Yuan; Ikhwan, Mohamad

2012-01-01

The current study reanalyzed 250 electrical fatalities in the construction industry from 1996 to 2002 into seven patterns based on source of electricity (power line, energized equipment, improperly installed or damaged equipment), direct contact or indirect contact through some source of injury (boom vehicle, metal bar or pipe, and other conductive material). Each fatality was coded in terms of age, company size, experience, performing tasks, source of injury, accident cause and hazard pattern. The Chi-square Automatic Interaction Detector (CHAID) was applied to the coded data of the fatal electrocution to find a subset of predictors that might derive meaningful classifications or accidents scenarios. A series of Flow Diagrams was constructed based on CHAID result to illustrate the flow of electricity travelling from electrical source to human body. Each of the flow diagrams can be directly linked with feasible prevention strategies by cutting the flow of electricity.

Phase Coexistence in a Dynamic Phase Diagram.

PubMed

Gentile, Luigi; Coppola, Luigi; Balog, Sandor; Mortensen, Kell; Ranieri, Giuseppe A; Olsson, Ulf

2015-08-03

Metastability and phase coexistence are important concepts in colloidal science. Typically, the phase diagram of colloidal systems is considered at the equilibrium without the presence of an external field. However, several studies have reported phase transition under mechanical deformation. The reason behind phase coexistence under shear flow is not fully understood. Here, multilamellar vesicle (MLV)-to-sponge (L3 ) and MLV-to-Lα transitions upon increasing temperature are detected using flow small-angle neutron scattering techniques. Coexistence of Lα and MLV phases at 40 °C under shear flow is detected by using flow NMR spectroscopy. The unusual rheological behavior observed by studying the lamellar phase of a non-ionic surfactant is explained using (2) H NMR and diffusion flow NMR spectroscopy with the coexistence of planar lamellar-multilamellar vesicles. Moreover, a dynamic phase diagram over a wide range of temperatures is proposed. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

WATER PROCESS SYSTEM FLOW DIAGRAM FOR MTR, TRA603. SUMMARY OF ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

WATER PROCESS SYSTEM FLOW DIAGRAM FOR MTR, TRA-603. SUMMARY OF COOLANT FLOW FROM WORKING RESERVOIR TO INTERIOR OF REACTOR'S THERMAL SHIELD. NAMES TANK SECTIONS. PIPE AND DRAIN-LINE SIZES. SHOWS DIRECTION OF AIR FLOW THROUGH PEBBLE AND GRAPHITE BLOCK ZONE. NEUTRON CURTAIN AND THERMAL COLUMN DOOR. BLAW-KNOX 3150-92-7, 3/1950. INL INDEX NO. 531-0603-51-098-100036, REV. 6. - Idaho National Engineering Laboratory, Test Reactor Area, Materials & Engineering Test Reactors, Scoville, Butte County, ID

Understanding the Periodic Table of Elements via Iconic Mapping and Sequential Diagramming: The Roundhouse Strategy

ERIC Educational Resources Information Center

Ward, Robin E.; Lee, William D.

2006-01-01

Roundhouse is a visually creative information-processing tool (J. E. Trowbridge and J. H. Wandersee 1998). The procedure requires learners to construct knowledge using "mindful" connections to replace less effective practices of memorizing fragmented information. Students create observable organization schemes of related ideas and icons in a…

Flow Effects on the Flammability Diagrams of Solid Fuels

NASA Technical Reports Server (NTRS)

Cordova, J. L.; Ceamanos, J.; Fernandez-Pello, A. C.; Long, R. T.; Torero, J. L.; Quintiere, J. G.

1997-01-01

A research program is currently underway with the final objective of developing a fundamental understanding of the controlling mechanisms underlying the flammability diagrams of solid combustible materials and their derived fire properties. Given that there is a high possibility of an accidental fire occurring in a space-based facility, understanding the fire properties of materials that will be used in such facilities is of critical importance. With this purpose, the flammability diagrams of the materials, as those produced by the Lateral Ignition and Flame Spread Test (LIFT) apparatus and by a new forced flow device, the Forced Flow Ignition and Flame Spread Test (FIST) apparatus, will be obtained. The specific objective of the program is to apply the new flammability apparatus, which will more accurately reflect the potential ambient conditions of space-based environments, to the characterization of the materials for space applications. This paper presents a parametric study of oxidizer flow effects on the ignition curve of the flammability diagrams of PMMA. The dependence of the ignition delay time on the external radiant flux and either the sample width (LIFT) or the flow velocity (FIST) has been studied. Although preliminary, the results indicate that natural and forced convection flow changes, affect the characteristics of the ignition curves of the flammability diagrams. The major effect on the ignition time appears to be due to convective transfer variations at the fuel surface. At high radiant fluxes or high flow velocities, however, it appears that gas phase processes become increasingly important, affecting the overall ignition delay time. A numerical analysis of the solid fuel heating and pyrolysis has also been developed. The theoretical predictions approximate the experiments well for conditions in which the gas phase induction time is negligible.

77 FR 35667 - Commission Information Collection Activities (FERC-567); Comment Request

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-14

... Act of 1995, 44 United States Code (U.S.C.) 3507(a)(1)(D), the Federal Energy Regulatory Commission... Reports of System Flow Diagrams and System Capacity to the Office of Management and Budget (OMB) for... System Flow Diagrams and System Capacity. OMB Control No.: 1902-0005. Type of Request: Three-year...

The Effect of Functional Flow Diagrams on Apprentice Aircraft Mechanics' Technical System Understanding.

ERIC Educational Resources Information Center

Johnson, Scott D.; Satchwell, Richard E.

1993-01-01

Describes an experimental study that tested the impact of a conceptual illustration on college students' understanding of the structure, function, and behavior of complex technical systems. The use of functional flow diagrams in aircraft mechanics' training is explained, a concept map analysis is discussed, and implications for technical training…

Advanced Information Processing System (AIPS) proof-of-concept system functional design I/O network system services

NASA Technical Reports Server (NTRS)

1985-01-01

The function design of the Input/Output (I/O) services for the Advanced Information Processing System (AIPS) proof of concept system is described. The data flow diagrams, which show the functional processes in I/O services and the data that flows among them, are contained. A complete list of the data identified on the data flow diagrams and in the process descriptions are provided.

Performance Analysis of the United States Marine Corps War Reserve Materiel Program Process Flow

DTIC Science & Technology

2016-12-01

or Less)............41 Figure 21. Tornado Diagram of Expected Delays Using 2016 Inputs ........................42 x Figure 22. Fishbone Diagram of...variability. Using Crystal Ball we produced a Tornado Diagram (similar to a Pareto Chart) in order to tell us where to focus our efforts. The results of...the Tornado Diagram are shown in Figure 21. Figure 21. Tornado Diagram of Expected Delays Using 2016 Inputs Using the results shown in the Tornado

Unsteady, one-dimensional gas dynamics computations using a TVD type sequential solver

NASA Technical Reports Server (NTRS)

Thakur, Siddharth; Shyy, Wei

1992-01-01

The efficacy of high resolution convection schemes to resolve sharp gradient in unsteady, 1D flows is examined using the TVD concept based on a sequential solution algorithm. Two unsteady flow problems are considered which include the problem involving the interaction of the various waves in a shock tube with closed reflecting ends and the problem involving the unsteady gas dynamics in a tube with closed ends subject to an initial pressure perturbation. It is concluded that high accuracy convection schemes in a sequential solution framework are capable of resolving discontinuities in unsteady flows involving complex gas dynamics. However, a sufficient amount of dissipation is required to suppress oscillations near discontinuities in the sequential approach, which leads to smearing of the solution profiles.

Reporting Guidelines: Optimal Use in Preventive Medicine and Public Health

PubMed Central

Popham, Karyn; Calo, William A.; Carpentier, Melissa Y.; Chen, Naomi E.; Kamrudin, Samira A.; Le, Yen-Chi L.; Skala, Katherine A.; Thornton, Logan R.; Mullen, Patricia Dolan

2012-01-01

Numerous reporting guidelines are available to help authors write higher quality manuscripts more efficiently. Almost 200 are listed on the EQUATOR (Enhancing the Quality and Transparency of Health Research) Network’s website and they vary in authority, usability, and breadth, making it difficult to decide which one(s) to use. This paper provides consistent information about guidelines for preventive medicine and public health and a framework and sequential approach for selecting them. EQUATOR guidelines were reviewed for relevance to target audiences; selected guidelines were classified as “core” (frequently recommended) or specialized, and the latter were grouped by their focus. Core and specialized guidelines were coded for indicators of authority (simultaneous publication in multiple journals, rationale, scientific background supporting each element, expertise of designers, permanent website/named group), usability (presence of checklists and examples of good reporting), and breadth (manuscript sections covered). Discrepancies were resolved by consensus. Selected guidelines are presented in four tables arranged to facilitate selection: core guidelines, all of which pertain to major research designs; guidelines for additional study designs, topical guidelines, and guidelines for particular manuscript sections. A flow diagram provides an overview. The framework and sequential approach will enable authors as well as editors, peer reviewers, researchers, and systematic reviewers to make optimal use of available guidelines to improve the transparency, clarity, and rigor of manuscripts and research protocols and the efficiency of conducing systematic reviews and meta-analyses. PMID:22992369

Enabling Metacognition in the Laboratory: A Case Study of Four Second Year University Chemistry Students.

ERIC Educational Resources Information Center

Davidowitz, Bette; Rollnick, Marissa

2003-01-01

Explores the Competency Tripod model and flow diagrams as two sources for enabling students' metacognition in a second year undergraduate chemistry laboratory. Results indicate that all four students engaged in metacognitive practices, all believed that flow diagrams are extremely useful, and all understood the Competency Tripod model, but only…

Fourth Graders' Cognitive Processes and Learning Strategies for Reading Illustrated Biology Texts: Eye Movement Measurements

ERIC Educational Resources Information Center

Jian, Yu-Cin

2016-01-01

Previous research suggests that multiple representations can improve science reading comprehension. This facilitation effect is premised on the observation that readers can efficiently integrate information in text and diagram formats; however, this effect in young readers is still contested. Using eye-tracking technology and sequential analysis,…

43 CFR 3274.11 - What must I give BLM to approve my commercial use permit application?

Code of Federal Regulations, 2014 CFR

2014-10-01

... configuration, including meters; (f) A schematic flow diagram of the utilization facility, including... calibration schedule of production, injection, and royalty meters; (b) A schematic diagram of the utilization... is located off the utilization site, give us a generalized schematic diagram of the electrical...

43 CFR 3274.11 - What must I give BLM to approve my commercial use permit application?

Code of Federal Regulations, 2012 CFR

2012-10-01

... configuration, including meters; (f) A schematic flow diagram of the utilization facility, including... calibration schedule of production, injection, and royalty meters; (b) A schematic diagram of the utilization... is located off the utilization site, give us a generalized schematic diagram of the electrical...

43 CFR 3274.11 - What must I give BLM to approve my commercial use permit application?

Code of Federal Regulations, 2011 CFR

2011-10-01

... configuration, including meters; (f) A schematic flow diagram of the utilization facility, including... calibration schedule of production, injection, and royalty meters; (b) A schematic diagram of the utilization... is located off the utilization site, give us a generalized schematic diagram of the electrical...

43 CFR 3274.11 - What must I give BLM to approve my commercial use permit application?

Code of Federal Regulations, 2013 CFR

2013-10-01

... configuration, including meters; (f) A schematic flow diagram of the utilization facility, including... calibration schedule of production, injection, and royalty meters; (b) A schematic diagram of the utilization... is located off the utilization site, give us a generalized schematic diagram of the electrical...

Advanced Platform Systems Technology study. Volume 4: Technology advancement program plan

NASA Technical Reports Server (NTRS)

1983-01-01

An overview study of the major technology definition tasks and subtasks along with their interfaces and interrelationships is presented. Although not specifically indicated in the diagram, iterations were required at many steps to finalize the results. The development of the integrated technology advancement plan was initiated by using the results of the previous two tasks, i.e., the trade studies and the preliminary cost and schedule estimates for the selected technologies. Descriptions for the development of each viable technology advancement was drawn from the trade studies. Additionally, a logic flow diagram depicting the steps in developing each technology element was developed along with descriptions for each of the major elements. Next, major elements of the logic flow diagrams were time phased, and that allowed the definition of a technology development schedule that was consistent with the space station program schedule when possible. Schedules show the major milestone including tests required as described in the logic flow diagrams.

Business Process Flow Diagrams in Tissue Bank Informatics System Design, and Identification and Communication of Best Practices: The Pharmaceutical Industry Experience.

PubMed

McDonald, Sandra A; Velasco, Elizabeth; Ilasi, Nicholas T

2010-12-01

Pfizer, Inc.'s Tissue Bank, in conjunction with Pfizer's BioBank (biofluid repository), endeavored to create an overarching internal software package to cover all general functions of both research facilities, including sample receipt, reconciliation, processing, storage, and ordering. Business process flow diagrams were developed by the Tissue Bank and Informatics teams as a way of characterizing best practices both within the Bank and in its interactions with key internal and external stakeholders. Besides serving as a first step for the software development, such formalized process maps greatly assisted the identification and communication of best practices and the optimization of current procedures. The diagrams shared here could assist other biospecimen research repositories (both pharmaceutical and other settings) for comparative purposes or as a guide to successful informatics design. Therefore, it is recommended that biorepositories consider establishing formalized business process flow diagrams for their laboratories, to address these objectives of communication and strategy.

VisFlow - Web-based Visualization Framework for Tabular Data with a Subset Flow Model.

PubMed

Yu, Bowen; Silva, Claudio T

2017-01-01

Data flow systems allow the user to design a flow diagram that specifies the relations between system components which process, filter or visually present the data. Visualization systems may benefit from user-defined data flows as an analysis typically consists of rendering multiple plots on demand and performing different types of interactive queries across coordinated views. In this paper, we propose VisFlow, a web-based visualization framework for tabular data that employs a specific type of data flow model called the subset flow model. VisFlow focuses on interactive queries within the data flow, overcoming the limitation of interactivity from past computational data flow systems. In particular, VisFlow applies embedded visualizations and supports interactive selections, brushing and linking within a visualization-oriented data flow. The model requires all data transmitted by the flow to be a data item subset (i.e. groups of table rows) of some original input table, so that rendering properties can be assigned to the subset unambiguously for tracking and comparison. VisFlow features the analysis flexibility of a flow diagram, and at the same time reduces the diagram complexity and improves usability. We demonstrate the capability of VisFlow on two case studies with domain experts on real-world datasets showing that VisFlow is capable of accomplishing a considerable set of visualization and analysis tasks. The VisFlow system is available as open source on GitHub.

36 CFR 14.78 - Applications.

Code of Federal Regulations, 2011 CFR

2011-07-01

... application should include a one-line diagram of the proposed line and the immediate interconnecting facilities including power plants and substations, a power flow diagram for proposed line and connecting...

36 CFR 14.78 - Applications.

Code of Federal Regulations, 2014 CFR

2014-07-01

... application should include a one-line diagram of the proposed line and the immediate interconnecting facilities including power plants and substations, a power flow diagram for proposed line and connecting...

36 CFR 14.78 - Applications.

Code of Federal Regulations, 2012 CFR

2012-07-01

... application should include a one-line diagram of the proposed line and the immediate interconnecting facilities including power plants and substations, a power flow diagram for proposed line and connecting...

36 CFR 14.78 - Applications.

Code of Federal Regulations, 2013 CFR

2013-07-01

... application should include a one-line diagram of the proposed line and the immediate interconnecting facilities including power plants and substations, a power flow diagram for proposed line and connecting...

Historical Analysis of C-130E Resources

DTIC Science & Technology

1977-07-01

DOCUMENTATION SEARCH AND COLLECTION FLOW 24 DIAGRAM 6. DATA ANALYSIS FLOW DIAGRAM TASK IV 29 7. C-130 INVENTORY BY CONFIGURATION 40 8. C-130 MISSION...RESORCE RESOURCES....EOUCE .’." * ESURE :;. 400 ................... - ., -...... ’.. ... ".......... ... ’... ’" SYSTEM DESIGN PERFORMANCE 4 , OPERATIO ...Force inventory , the control of the human and material resources crosses several functions and commands. Seldom are the initial estimates verified

A master dynamic flow diagram for the shear thickening transition in micellar solutions.

PubMed

Bautista, F; Tepale, N; Fernández, V V A; Landázuri, G; Hernández, E; Macías, E R; Soltero, J F A; Escalante, J I; Manero, O; Puig, J E

2016-01-07

The shear thickening behavior of dilute micellar solutions of hexadecyltrimethylammonium-type surfactants with different counterions (tosylate, 3- and 4-fluorobenzoate, vinylbenzoate and salicylate) and of n-alkyltetradecylammonium bromide (CnTAB), with n = 14, 16 and 18, is examined here. These solutions undergo a shear thickening transition due to the formation of shear-induced structures (SISs) in the shear range studied. Here we report a relationship between the shear thickening intensity and the differences in the hydrophobicity of counterions according to the Hofmeister-like anion series, which leads to a master flow diagram. This master flow diagram is produced by plotting a normalized shear thickening intensity (Iη - 1)/(Imax - 1) versus CD/CD,max, where Iη is the shear-thickening intensity, defined as the largest viscosity obtained in the shear-thickening transition (STT) at a given surfactant concentration CD divided by the Newtonian viscosity η0, and Imax is the largest intensity value obtained in the STT at a surfactant concentration CD,max. The master flow diagram is built using several cetyltrimethylammonium-type surfactants with different counterions, according to a Hofmeister-like series, and by n-alkyltetradecylammonium bromide surfactants with different alkyl chain lengths.

Multiloop Functional Renormalization Group That Sums Up All Parquet Diagrams

NASA Astrophysics Data System (ADS)

Kugler, Fabian B.; von Delft, Jan

2018-02-01

We present a multiloop flow equation for the four-point vertex in the functional renormalization group (FRG) framework. The multiloop flow consists of successive one-loop calculations and sums up all parquet diagrams to arbitrary order. This provides substantial improvement of FRG computations for the four-point vertex and, consequently, the self-energy. Using the x-ray-edge singularity as an example, we show that solving the multiloop FRG flow is equivalent to solving the (first-order) parquet equations and illustrate this with numerical results.

Information Flow in the Launch Vehicle Design/Analysis Process

NASA Technical Reports Server (NTRS)

Humphries, W. R., Sr.; Holland, W.; Bishop, R.

1999-01-01

This paper describes the results of a team effort aimed at defining the information flow between disciplines at the Marshall Space Flight Center (MSFC) engaged in the design of space launch vehicles. The information flow is modeled at a first level and is described using three types of templates: an N x N diagram, discipline flow diagrams, and discipline task descriptions. It is intended to provide engineers with an understanding of the connections between what they do and where it fits in the overall design process of the project. It is also intended to provide design managers with a better understanding of information flow in the launch vehicle design cycle.

PRELIMINARY DESIGN ANALYSIS OF AXIAL FLOW TURBINES

NASA Technical Reports Server (NTRS)

Glassman, A. J.

1994-01-01

A computer program has been developed for the preliminary design analysis of axial-flow turbines. Rapid approximate generalized procedures requiring minimum input are used to provide turbine overall geometry and performance adequate for screening studies. The computations are based on mean-diameter flow properties and a stage-average velocity diagram. Gas properties are assumed constant throughout the turbine. For any given turbine, all stages, except the first, are specified to have the same shape velocity diagram. The first stage differs only in the value of inlet flow angle. The velocity diagram shape depends upon the stage work factor value and the specified type of velocity diagram. Velocity diagrams can be specified as symmetrical, zero exit swirl, or impulse; or by inputting stage swirl split. Exit turning vanes can be included in the design. The 1991 update includes a generalized velocity diagram, a more flexible meanline path, a reheat model, a radial component of velocity, and a computation of free-vortex hub and tip velocity diagrams. Also, a loss-coefficient calibration was performed to provide recommended values for airbreathing engine turbines. Input design requirements include power or pressure ratio, mass flow rate, inlet temperature and pressure, and rotative speed. The design variables include inlet and exit diameters, stator angle or exit radius ratio, and number of stages. Gas properties are input as gas constant, specific heat ratio, and viscosity. The program output includes inlet and exit annulus dimensions, exit temperature and pressure, total and static efficiencies, flow angles, blading angles, and last stage absolute and relative Mach numbers. This program is written in FORTRAN 77 and can be ported to any computer with a standard FORTRAN compiler which supports NAMELIST. It was originally developed on an IBM 7000 series computer running VM and has been implemented on IBM PC computers and compatibles running MS-DOS under Lahey FORTRAN, and DEC VAX series computers running VMS. Format statements in the code may need to be rewritten depending on your FORTRAN compiler. The source code and sample data are available on a 5.25 inch 360K MS-DOS format diskette. This program was developed in 1972 and was last updated in 1991. IBM and IBM PC are registered trademarks of International Business Machines. MS-DOS is a registered trademark of Microsoft Corporation. DEC VAX, and VMS are trademarks of Digital Equipment Corporation.

The Development of Multi-Level Audio-Visual Teaching Aids for Earth Science.

ERIC Educational Resources Information Center

Pitt, William D.

The project consisted of making a multi-level teaching film titled "Rocks and Minerals of the Ouachita Mountains," which runs for 25 minutes and is in color. The film was designed to be interesting to earth science students from junior high to college, and consists of dialogue combined with motion pictures of charts, sequential diagrams, outcrops,…

Supporting Learning and Promoting Conceptual Change with Box and AVOW Diagrams. Part 2: Their Impact on Student Learning at A-Level.

ERIC Educational Resources Information Center

Cheng, Peter C-H.; Shipstone, David M.

2003-01-01

Presents results of preliminary trials that suggest that the program devised helped UK Year 12 (A-level) learners develop useful concepts of current and voltage, acquire a more integrated understanding of circuit behavior, and overcome their tendencies towards localized and sequential reasoning. Provides learners with a valuable aid for problem…

The Interaction of Child-Parent Shared Reading with an Augmented Reality (AR) Picture Book and Parents' Conceptions of AR Learning

ERIC Educational Resources Information Center

Cheng, Kun-Hung; Tsai, Chin-Chung

2016-01-01

Following a previous study (Cheng & Tsai, 2014. "Computers & Education"), this study aimed to probe the interaction of child-parent shared reading with the augmented reality (AR) picture book in more depth. A series of sequential analyses were thus conducted to infer the behavioral transition diagrams and visualize the continuity…

CADDIS Volume 2. Sources, Stressors and Responses: Flow Alteration

EPA Pesticide Factsheets

Introduction to the flow alteration module, when to list flow alteration as a candidate cause, ways to measure flow alteration, simple and detailed conceptual model diagrams for flow alteration, flow alteration module references and literature reviews.

Modern Mathematical Topics in Chemistry.

ERIC Educational Resources Information Center

Henson, R. C.; Stumbles, A. M.

1979-01-01

Discusses how modern mathematical language can be used to develop chemical ideas in class. Examples for the application of Venn Diagrams and Flow Diagrams in teaching chemistry in the Nuffield courses are presented. (HM)

RDX/HMX Plant Design

DTIC Science & Technology

1981-05-01

coating process in Explosives Manufacturing Line 2. The end products of the initial design effort are process flow diagrams, piping and...instrumentation diagrams, motor control schedules, interlock logic diagrams, piping installation drawings, typical instrument Installation details, equipment...structures, equipment, utilities, and process piping extending 1.5 m (5 ft) beyond the building or area were not included in the scope of work. Nitrolysis

The Role of Graphic Elements in the Accurate Portrayal of Instructional Design.

ERIC Educational Resources Information Center

Branch, Robert C.; Bloom, Janet R.

This study explores the interpretation of two types of flow diagrams composed of different visual elements intended to communicate the same meaning. Using linear and cyclical diagrams, the study focused on whether, given a series of diagrams using linear elements and a series using cyclical elements, both types of visuals convey the same message…

GENERAL: A modified weighted probabilistic cellular automaton traffic flow model

NASA Astrophysics Data System (ADS)

Zhuang, Qian; Jia, Bin; Li, Xin-Gang

2009-08-01

This paper modifies the weighted probabilistic cellular automaton model (Li X L, Kuang H, Song T, et al 2008 Chin. Phys. B 17 2366) which considered a diversity of traffic behaviors under real traffic situations induced by various driving characters and habits. In the new model, the effects of the velocity at the last time step and drivers' desire for acceleration are taken into account. The fundamental diagram, spatial-temporal diagram, and the time series of one-minute data are analyzed. The results show that this model reproduces synchronized flow. Finally, it simulates the on-ramp system with the proposed model. Some characteristics including the phase diagram are studied.

Reappraisal of criticality for two-layer flows and its role in the generation of internal solitary waves

NASA Astrophysics Data System (ADS)

Bridges, Thomas J.; Donaldson, Neil M.

2007-07-01

A geometric view of criticality for two-layer flows is presented. Uniform flows are classified by diagrams in the momentum-massflux space for fixed Bernoulli energy, and cuspoidal curves on these diagrams correspond to critical uniform flows. Restriction of these surfaces to critical flow leads to new subsurfaces in energy-massflux space. While the connection between criticality and the generation of solitary waves is well known, we find that the nonlinear properties of these bifurcating solitary waves are also determined by the properties of the criticality surfaces. To be specific, the case of two layers with a rigid lid is considered, and application of the theory to other multilayer flows is sketched.

Phase diagram of single vesicle dynamical states in shear flow.

PubMed

Deschamps, J; Kantsler, V; Steinberg, V

2009-03-20

We report the first experimental phase diagram of vesicle dynamical states in a shear flow presented in a space of two dimensionless parameters suggested recently by V. Lebedev et al. To reduce errors in the control parameters, 3D geometrical reconstruction and determination of the viscosity contrast of a vesicle in situ in a plane Couette flow device prior to the experiment are developed. Our results are in accord with the theory predicting three distinctly separating regions of vesicle dynamical states in the plane of just two self-similar parameters.

Blade selection for a modern axial-flow compressor

NASA Technical Reports Server (NTRS)

Wright, L. C.

1974-01-01

The procedures leading to successful design of an axial flow compressor are discussed. The three related approaches to cascade selection are: (1) experimental approach which relies on the use of experimental results from identical cascades to satisfy the velocity diagrams calculated, (2) a purely analytical procedure whereby blade shapes are calculated from the theoretical cascade and viscous flow equations, and (3) a semiempirical procedure which used experimental data together with the theoretically derived functional relations to relate the cascade parameters. Diagrams of typical transonic blade sections with uncambered leading edges are presented.

Shape diagram of vesicles in Poiseuille flow.

PubMed

Coupier, Gwennou; Farutin, Alexander; Minetti, Christophe; Podgorski, Thomas; Misbah, Chaouqi

2012-04-27

Soft bodies flowing in a channel often exhibit parachutelike shapes usually attributed to an increase of hydrodynamic constraint (viscous stress and/or confinement). We show that the presence of a fluid membrane leads to the reverse phenomenon and build a phase diagram of shapes-which are classified as bullet, croissant, and parachute-in channels of varying aspect ratio. Unexpectedly, shapes are relatively wider in the narrowest direction of the channel. We highlight the role of flow patterns on the membrane in this response to the asymmetry of stress distribution.

Deformation and dynamics of red blood cells in flow through cylindrical microchannels.

PubMed

Fedosov, Dmitry A; Peltomäki, Matti; Gompper, Gerhard

2014-06-28

The motion of red blood cells (RBCs) in microcirculation plays an important role in blood flow resistance and in the cell partitioning within a microvascular network. Different shapes and dynamics of RBCs in microvessels have been previously observed experimentally including the parachute and slipper shapes. We employ mesoscale hydrodynamic simulations to predict the phase diagram of shapes and dynamics of RBCs in cylindrical microchannels, which serve as idealized microvessels, for a wide range of channel confinements and flow rates. A rich dynamical behavior is found, with snaking and tumbling discocytes, slippers performing a swinging motion, and stationary parachutes. We discuss the effects of different RBC states on the flow resistance, and the influence of RBC properties, characterized by the Föppl-von Kármán number, on the shape diagram. The simulations are performed using the same viscosity for both external and internal fluids surrounding a RBC; however, we discuss how the viscosity contrast would affect the shape diagram.

Sequential continuous flow processes for the oxidation of amines and azides by using HOF·MeCN.

PubMed

McPake, Christopher B; Murray, Christopher B; Sandford, Graham

2012-02-13

The generation and use of the highly potent oxidising agent HOF·MeCN in a controlled single continuous flow process is described. Oxidations of amines and azides to corresponding nitrated systems by using fluorine gas, water and acetonitrile by sequential gas-liquid/liquid-liquid continuous flow procedures are reported. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

CADDIS Volume 2. Sources, Stressors and Responses: Simple and Detailed Conceptual Model Diagram Downloads

EPA Pesticide Factsheets

Simple and detailed conceptual model diagram and associated narrative for ammonia, dissolved oxygen, flow alteration, herbicides, insecticides, ionic strength, metals, nutrients, ph, physical habitat, sediments, temperature, unspecified toxic chemicals.

Andreas Acrivos Dissertation Prize Lecture: Stability of inviscid flows from bifurcation diagrams exploiting a variational argument

NASA Astrophysics Data System (ADS)

Luzzatto-Fegiz, Paolo

2011-11-01

Steady fluid solutions play a special role in the dynamics of a flow: stable states may be realized in practice, while unstable ones may act as attractors. Unfortunately, determining stability is often a process far more laborious than finding steady states; indeed, even for simple vortex or wave flows, stability properties have often been the subject of debate. We consider here a stability idea originating with Lord Kelvin (1876), which involves using the second variation of the energy, δ2 E , to establish bounds on a perturbation. However, for numerically obtained flows, computing δ2 E explicitly is often not feasible. To circumvent this issue, Saffman & Szeto (1980) proposed an argument linking changes in δ2 E to turning points in a bifurcation diagram, for families of steady flows. Later work has shown that this argument is unreliable; the two key issues are associated with the absence of a formal turning-point theory, and with the inability to detect bifurcations (Dritschel 1995, and references therein). In this work, we build on ideas from bifurcation theory, and link turning points in a velocity-impulse diagram to changes in δ2 E ; in addition, this diagram delivers the direction of the change of δ2 E , thereby providing information as to whether stability is gained or lost. To detect hidden solution branches, we introduce to these fluid problems concepts from imperfection theory. The resulting approach, involving ``imperfect velocity-impulse'' diagrams, leads us to new and surprising results for a wide range of fundamental vortex and wave flows; we mention here the calculation of the first steady vortices without any symmetry, and the uncovering of the complete solution structure for vortex pairs. In addition, we find precise agreement with available results from linear stability analysis. Doctoral work advised by C.H.K. Williamson at Cornell University.

CFD simulation of hemodynamics in sequential and individual coronary bypass grafts based on multislice CT scan datasets.

PubMed

Hajati, Omid; Zarrabi, Khalil; Karimi, Reza; Hajati, Azadeh

2012-01-01

There is still controversy over the differences in the patency rates of the sequential and individual coronary artery bypass grafting (CABG) techniques. The purpose of this paper was to non-invasively evaluate hemodynamic parameters using complete 3D computational fluid dynamics (CFD) simulations of the sequential and the individual methods based on the patient-specific data extracted from computed tomography (CT) angiography. For CFD analysis, the geometric model of coronary arteries was reconstructed using an ECG-gated 64-detector row CT. Modeling the sequential and individual bypass grafting, this study simulates the flow from the aorta to the occluded posterior descending artery (PDA) and the posterior left ventricle (PLV) vessel with six coronary branches based on the physiologically measured inlet flow as the boundary condition. The maximum calculated wall shear stress (WSS) in the sequential and the individual models were estimated to be 35.1 N/m(2) and 36.5 N/m(2), respectively. Compared to the individual bypass method, the sequential graft has shown a higher velocity at the proximal segment and lower spatial wall shear stress gradient (SWSSG) due to the flow splitting caused by the side-to-side anastomosis. Simulated results combined with its surgical benefits including the requirement of shorter vein length and fewer anastomoses advocate the sequential method as a more favorable CABG method.

Stepwise Bose-Einstein Condensation in a Spinor Gas.

PubMed

Frapolli, C; Zibold, T; Invernizzi, A; Jiménez-García, K; Dalibard, J; Gerbier, F

2017-08-04

We observe multistep condensation of sodium atoms with spin F=1, where the different Zeeman components m_{F}=0,±1 condense sequentially as the temperature decreases. The precise sequence changes drastically depending on the magnetization m_{z} and on the quadratic Zeeman energy q (QZE) in an applied magnetic field. For large QZE, the overall structure of the phase diagram is the same as for an ideal spin-1 gas, although the precise locations of the phase boundaries are significantly shifted by interactions. For small QZE, antiferromagnetic interactions qualitatively change the phase diagram with respect to the ideal case, leading, for instance, to condensation in m_{F}=±1, a phenomenon that cannot occur for an ideal gas with q>0.

Flow equation for porous plug and capillary tube flow restrictors

NASA Technical Reports Server (NTRS)

Davis, W. S.

1972-01-01

Development of flow measuring apparatus for determining low flow performance of resistojet thruster is discussed. Diagram of test equipment is presented. Operation of test equipment is described and numerical relationships are explained.

Development of the Functional Flow Block Diagram for the J-2X Rocket Engine System

NASA Technical Reports Server (NTRS)

White, Thomas; Stoller, Sandra L.; Greene, WIlliam D.; Christenson, Rick L.; Bowen, Barry C.

2007-01-01

The J-2X program calls for the upgrade of the Apollo-era Rocketdyne J-2 engine to higher power levels, using new materials and manufacturing techniques, and with more restrictive safety and reliability requirements than prior human-rated engines in NASA history. Such requirements demand a comprehensive systems engineering effort to ensure success. Pratt & Whitney Rocketdyne system engineers performed a functional analysis of the engine to establish the functional architecture. J-2X functions were captured in six major operational blocks. Each block was divided into sub-blocks or states. In each sub-block, functions necessary to perform each state were determined. A functional engine schematic consistent with the fidelity of the system model was defined for this analysis. The blocks, sub-blocks, and functions were sequentially numbered to differentiate the states in which the function were performed and to indicate the sequence of events. The Engine System was functionally partitioned, to provide separate and unique functional operators. Establishing unique functional operators as work output of the System Architecture process is novel in Liquid Propulsion Engine design. Each functional operator was described such that its unique functionality was identified. The decomposed functions were then allocated to the functional operators both of which were the inputs to the subsystem or component performance specifications. PWR also used a novel approach to identify and map the engine functional requirements to customer-specified functions. The final result was a comprehensive Functional Flow Block Diagram (FFBD) for the J-2X Engine System, decomposed to the component level and mapped to all functional requirements. This FFBD greatly facilitates component specification development, providing a well-defined trade space for functional trades at the subsystem and component level. It also provides a framework for function-based failure modes and effects analysis (FMEA), and a rigorous baseline for the functional architecture.

Hertzsprung and Russell: The Minards of Astronomy

NASA Astrophysics Data System (ADS)

Broek, J. V. D.; Russo, P.

2014-01-01

This article will explore the history of flow maps, the extent of their use and how astronomy has benefited from this illustrative way of communicating ideas. Flow maps are multidimensional infographics that tell a long story in one single image. In 1812 the French civil engineer Charles Joseph Minard created a flow map that is still dubbed "the mother of all flow maps", summarising Napoleon's Russian campaign (Figure 1). Almost 100 years later, in 1910, Ejnar Hertzsprung and Henry Norris Russell created a multidimensional flow map that arguably surpasses Minard's map in ingenuity -- the Hertzprung-Russell diagram. The Hertzprung-Russell diagram represents a major step towards an understanding of stellar evolution, or "the lives of stars", and is still used in astronomy today.

Improvements in Routing for Packet-Switched Networks

DTIC Science & Technology

1975-02-18

PROGRAM FOR COMPUTER SIMULATION . . 90 B.l Flow Diagram of Adaptive Routine 90 B.2 Progiam ARPSIM 93 B.3 Explanation of Variables...equa. 90 APPENDIX B ADAPTIVE ROUTING PROGRAM FOR COMPUTER SIMULA HON The computer simulation for adaptive routing was initially run on a DDP-24 small...TRANSMIT OVER AVAILABLE LINKS MESSAGES IN QUEUE COMPUTE Ni NUMBER OF ARRIVALS AT EACH NODE i AT TIME T Fig. Bla - Flow Diagram of Program Routine 92

Development of a low-flow multiplexed interface for capillary electrophoresis/electrospray ion trap mass spectrometry using sequential spray.

PubMed

Chen, Chao-Jung; Li, Fu-An; Her, Guor-Rong

2008-05-01

A multiplexed CE-MS interface using four low-flow sheath liquid ESI sprayers has been developed. Because of the limited space between the low-flow sprayers and the entrance aperture of the ESI source, multichannel analysis is difficult using conventional rotating plate approaches. Instead, a multiplexed low-flow system was achieved by applying an ESI potential sequentially to the four low-flow sprayers, resulting in only one sprayer being sprayed at any given time. The synchronization of the scan event and the voltage relays was accomplished by using the data acquisition signal from the IT mass spectrometer. This synchronization resulted in the ESI voltage being sequentially applied to each of the four sprayers according to the corresponding scan event. With this design, a four-fold increase in analytical throughput was achieved. Because of the use of low-flow interfaces, this multiplexed system has superior sensitivity than a rotating plate design using conventional sheath liquid interfaces. The multiplexed design presented has the potential to be applied to other low-flow multiplexed systems, such as multiplexed capillary LC and multiplexed CEC.

Sequential elution process

DOEpatents

Kingsley, I.S.

1987-01-06

A process and apparatus are disclosed for the separation of complex mixtures of carbonaceous material by sequential elution with successively stronger solvents. In the process, a column containing glass beads is maintained in a fluidized state by a rapidly flowing stream of a weak solvent, and the sample is injected into this flowing stream such that a portion of the sample is dissolved therein and the remainder of the sample is precipitated therein and collected as a uniform deposit on the glass beads. Successively stronger solvents are then passed through the column to sequentially elute less soluble materials. 1 fig.

Quantification of the level of crowdedness for pedestrian movements

NASA Astrophysics Data System (ADS)

Duives, Dorine C.; Daamen, Winnie; Hoogendoorn, Serge P.

2015-06-01

Within the realm of pedestrian research numerous measures have been proposed to estimate the level of crowdedness experienced by pedestrians. However, within the field of pedestrian traffic flow modelling there does not seem to be consensus on the question which of these measures performs best. This paper shows that the shape and scatter within the resulting fundamental diagrams differs a lot depending on the measure of crowdedness used. The main aim of the paper is to establish the advantages and disadvantages of the currently existing measures to quantify crowdedness in order to evaluate which measures provide both accurate and consistent results. The assessment is not only based on the theoretical differences, but also on the qualitative and quantitative differences between the resulting fundamental diagrams computed using the crowdedness measures on one and the same data set. The qualitative and quantitative functioning of the classical Grid-based measure is compared to with the X-T measure, an Exponentially Weighted Distance measure, and a Voronoi-Diagram measure. The consistency of relating these measures for crowdedness to the two macroscopic flow variables velocity and flow, the computational efficiency and the amount of scatter present within the fundamental diagrams produced by the implementation of the different measures are reviewed. It is found that the Voronoi-Diagram and X-T measure are the most efficient and consistent measures for crowdedness.

A Whale of a Tale: Creating Spacecraft Telemetry Data Analysis Products for the Deep Impact Mission

NASA Technical Reports Server (NTRS)

Sturdevant, Kathryn

2006-01-01

A description of the Whale product generation utility and its means of analyzing project data for Deep Impact Missions is presented. The topics include: 1) Whale Definition; 2) Whale Overview; 3) Whale Challenges; 4) Network Configuration; 5) Network Diagram; 6) Whale Data Flow: Design Decisions; 7) Whale Data Flow Diagram; 8) Whale Data Flow; 9) Whale Team and Users; 10) Creeping Requirements; 11) Whale Competition; 12) Statistics: Processing Time; 13) CPU and Disk Usage; 14) The Ripple Effect of More Data; and 15) Data Validation and the Automation Challenge.

Kinetic: A system code for analyzing nuclear thermal propulsion rocket engine transients

NASA Astrophysics Data System (ADS)

Schmidt, Eldon; Lazareth, Otto; Ludewig, Hans

The topics are presented in viewgraph form and include the following: outline of kinetic code; a kinetic information flow diagram; kinetic neutronic equations; turbopump/nozzle algorithm; kinetic heat transfer equations per node; and test problem diagram.

Numerical results for axial flow compressor instability

NASA Technical Reports Server (NTRS)

Mccaughan, F. E.

1988-01-01

Using Cornell's supercomputing facilities, an extensive study of the Moore-Greitzer model was carried out, which gives accurate and reliable information about compressor instability. The bifurcation analysis in the companion paper shows the dependence of the mode of compressor response on the shape of the rotating stall characteristic. The numerical results verify and extend this with a more accurate representation of the characteristic. The effect of the parameters on the shape of the rotating stall characteristic is investigated, and it is found that the parameters with the strongest effects are the inlet length, and the shape of the compressor pressure rise vs. mass flow diagram (i.e. tall diagrams vs. shallow diagrams). The effects of inlet guide vane loss on the characteristic are discussed.

18 CFR 156.5 - Exhibits.

Code of Federal Regulations, 2011 CFR

2011-04-01

... showing daily design capacity and reflecting operation with proposed transmission facilities. A flow diagram showing daily design capacity of all transmission facilities proposed to be installed and operated... engineering design data in explanation and support of the diagrams and the proposed project, setting forth: (i...

18 CFR 156.5 - Exhibits.

Code of Federal Regulations, 2012 CFR

2012-04-01

... showing daily design capacity and reflecting operation with proposed transmission facilities. A flow diagram showing daily design capacity of all transmission facilities proposed to be installed and operated... engineering design data in explanation and support of the diagrams and the proposed project, setting forth: (i...

18 CFR 156.5 - Exhibits.

Code of Federal Regulations, 2010 CFR

2010-04-01

... showing daily design capacity and reflecting operation with proposed transmission facilities. A flow diagram showing daily design capacity of all transmission facilities proposed to be installed and operated... engineering design data in explanation and support of the diagrams and the proposed project, setting forth: (i...

18 CFR 156.5 - Exhibits.

Code of Federal Regulations, 2014 CFR

2014-04-01

... showing daily design capacity and reflecting operation with proposed transmission facilities. A flow diagram showing daily design capacity of all transmission facilities proposed to be installed and operated... engineering design data in explanation and support of the diagrams and the proposed project, setting forth: (i...

18 CFR 156.5 - Exhibits.

Code of Federal Regulations, 2013 CFR

2013-04-01

... showing daily design capacity and reflecting operation with proposed transmission facilities. A flow diagram showing daily design capacity of all transmission facilities proposed to be installed and operated... engineering design data in explanation and support of the diagrams and the proposed project, setting forth: (i...

Energy Flow through a Paper Ecosystem.

ERIC Educational Resources Information Center

Aston, T. J.

1988-01-01

Presented is an exercise for high school students which illustrates the principle and practice of measuring energy flow through a community. Included are worksheets, instructions, a flow diagram, and a list of ecosystem parameters. (Author/CW)

Information-Systems Data-Flow Diagram

NASA Technical Reports Server (NTRS)

Blosiu, J. O.

1983-01-01

Single form presents clear picture of entire system. Form giving relational review of data flow well suited to information system planning, analysis, engineering, and management. Used to review data flow for developing system or one already in use.

Mycology at a distance.

PubMed

Koneman, Elmer; Gade, Wayne

2002-01-01

GermWare Mycology is an image-rich, CD-ROM-based instruction divided into tutorial and reference programs. The tutorial program, designed for new students, provides only for sequential progress through each of the subject modules, so that each page of information is seen. In contrast, the reference program allows the more experienced learner with random and direct access to each facet of information. The aspergilli, the agents of chromomycosis, the dermatophytes, the dimorphic fungi, the hyaline molds, the dematiaceous molds, the yeasts, and the zygomyces are divided into separate modules. The tutorial program also includes an opening 'isolation procedures' module, in which details of specimen collection, culture media, and microscopic techniques are presented. The random access program includes system maps separating out each of the fungal species, and flow diagrams allowing an algorithm approach to species identifications. A global map is also included through which each fungal species can be directly accessed by the simple click of the mouse. Random access to information on the ecology, clinical presentations, pathology and therapy of the various mycotic diseases is also a feature of the reference program. A series of self-assessment exercises is included at the end of each module, with immediate 'pop-up' feedback to both correct and incorrect answers. The entire program includes over 2500 screens and over 700 color images and diagrams. GermWare Mycology is available through the Colorado Association for Continuing Medical Laboratory Education (CACMLE), who also can provide continuing education credits for individuals who complete a separate examination. For more information contact CACMLE at (303) 321-1734 or info@cacmle.org.

Visualization design and verification of Ada tasking using timing diagrams

NASA Technical Reports Server (NTRS)

Vidale, R. F.; Szulewski, P. A.; Weiss, J. B.

1986-01-01

The use of timing diagrams is recommended in the design and testing of multi-task Ada programs. By displaying the task states vs. time, timing diagrams can portray the simultaneous threads of data flow and control which characterize tasking programs. This description of the system's dynamic behavior from conception to testing is a necessary adjunct to other graphical techniques, such as structure charts, which essentially give a static view of the system. A series of steps is recommended which incorporates timing diagrams into the design process. Finally, a description is provided of a prototype Ada Execution Analyzer (AEA) which automates the production of timing diagrams from VAX/Ada debugger output.

A Numerical Study of New Logistic Map

NASA Astrophysics Data System (ADS)

Khmou, Youssef

In this paper, we propose a new logistic map based on the relation of the information entropy, we study the bifurcation diagram comparatively to the standard logistic map. In the first part, we compare the obtained diagram, by numerical simulations, with that of the standard logistic map. It is found that the structures of both diagrams are similar where the range of the growth parameter is restricted to the interval [0,e]. In the second part, we present an application of the proposed map in traffic flow using macroscopic model. It is found that the bifurcation diagram is an exact model of the Greenberg’s model of traffic flow where the growth parameter corresponds to the optimal velocity and the random sequence corresponds to the density. In the last part, we present a second possible application of the proposed map which consists of random number generation. The results of the analysis show that the excluded initial values of the sequences are (0,1).

Development of enantioselective chemiluminescence flow- and sequential-injection immunoassays for alpha-amino acids.

PubMed

Silvaieh, Hossein; Schmid, Martin G; Hofstetter, Oliver; Schurig, Volker; Gübitz, Gerald

2002-01-01

The development of an enantioselective flow-through chemiluminescence immunosensor for amino acids is described. The approach is based on a competitive assay using enantioselective antibodies. Two different instrumental approaches, a flow-injection (FIA) and a sequential-injection system (SIA), are used. Compared to the flow-injection technique, the sequential injection-mode showed better repeatability. Both systems use an immunoreactor consisting of a flow cell packed with immobilized haptens. The haptens (4-amino-L- or D-phenylalanine) are immobilized onto a hydroxysuccinimide-activated polymer (Affi-prep 10) via a tyramine spacer. Stereoselective antibodies, raised against 4-amino-L- or D-phenylalanine, are labeled with an acridinium ester. Stereoselective inhibition of binding of the acridinum-labeled antibodies to the immobilized hapten by amino acids takes place. Chiral recognition was observed not only for the hapten molecule but also for a series of different amino acids. One assay cycle including regeneration takes 6:30 min in the FIA mode and 4:40 min in the SIA mode. Using D-phenylalanine as a sample, the detection limit was found to be 6.13 pmol/ml (1.01 ng/ml) for the flow-injection immunoassay (FIIA) and 1.76 pmol/ml (0.29 ng/ml ) for the sequential-injection immunoassay (SIIA) which can be lowered to 0.22 pmol/ml (0.036 ng/ml) or 0.064 pmol/ml (0.01 ng/ml) by using a stopped flow system. The intra-assay repeatability was found to be about 5% RSD and the inter-assay repeatability below 6% (within 3 days).

Stepwise positional-orientational order and the multicritical-multistructural global phase diagram of the s=3/2 Ising model from renormalization-group theory.

PubMed

Yunus, Çağın; Renklioğlu, Başak; Keskin, Mustafa; Berker, A Nihat

2016-06-01

The spin-3/2 Ising model, with nearest-neighbor interactions only, is the prototypical system with two different ordering species, with concentrations regulated by a chemical potential. Its global phase diagram, obtained in d=3 by renormalization-group theory in the Migdal-Kadanoff approximation or equivalently as an exact solution of a d=3 hierarchical lattice, with flows subtended by 40 different fixed points, presents a very rich structure containing eight different ordered and disordered phases, with more than 14 different types of phase diagrams in temperature and chemical potential. It exhibits phases with orientational and/or positional order. It also exhibits quintuple phase transition reentrances. Universality of critical exponents is conserved across different renormalization-group flow basins via redundant fixed points. One of the phase diagrams contains a plastic crystal sequence, with positional and orientational ordering encountered consecutively as temperature is lowered. The global phase diagram also contains double critical points, first-order and critical lines between two ordered phases, critical end points, usual and unusual (inverted) bicritical points, tricritical points, multiple tetracritical points, and zero-temperature criticality and bicriticality. The four-state Potts permutation-symmetric subspace is contained in this model.

Improved workflow modelling using role activity diagram-based modelling with application to a radiology service case study.

PubMed

Shukla, Nagesh; Keast, John E; Ceglarek, Darek

2014-10-01

The modelling of complex workflows is an important problem-solving technique within healthcare settings. However, currently most of the workflow models use a simplified flow chart of patient flow obtained using on-site observations, group-based debates and brainstorming sessions, together with historic patient data. This paper presents a systematic and semi-automatic methodology for knowledge acquisition with detailed process representation using sequential interviews of people in the key roles involved in the service delivery process. The proposed methodology allows the modelling of roles, interactions, actions, and decisions involved in the service delivery process. This approach is based on protocol generation and analysis techniques such as: (i) initial protocol generation based on qualitative interviews of radiology staff, (ii) extraction of key features of the service delivery process, (iii) discovering the relationships among the key features extracted, and, (iv) a graphical representation of the final structured model of the service delivery process. The methodology is demonstrated through a case study of a magnetic resonance (MR) scanning service-delivery process in the radiology department of a large hospital. A set of guidelines is also presented in this paper to visually analyze the resulting process model for identifying process vulnerabilities. A comparative analysis of different workflow models is also conducted. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

Lageos assembly operation plan

NASA Technical Reports Server (NTRS)

Brueger, J.

1975-01-01

Guidelines and constraints procedures for LAGEOS assembly, operation, and design performance are given. Special attention was given to thermal, optical, and dynamic analysis and testing. The operation procedures illustrate the interrelation and sequence of tasks in a flow diagram. The diagram also includes quality assurance functions for verification of operation tasks.

Mars Science Laboratory CHIMRA/IC/DRT Flight Software for Sample Acquisition and Processing

NASA Technical Reports Server (NTRS)

Kim, Won S.; Leger, Chris; Carsten, Joseph; Helmick, Daniel; Kuhn, Stephen; Redick, Richard; Trujillo, Diana

2013-01-01

The design methodologies of using sequence diagrams, multi-process functional flow diagrams, and hierarchical state machines were successfully applied in designing three MSL (Mars Science Laboratory) flight software modules responsible for handling actuator motions of the CHIMRA (Collection and Handling for In Situ Martian Rock Analysis), IC (Inlet Covers), and DRT (Dust Removal Tool) mechanisms. The methodologies were essential to specify complex interactions with other modules, support concurrent foreground and background motions, and handle various fault protections. Studying task scenarios with multi-process functional flow diagrams yielded great insight to overall design perspectives. Since the three modules require three different levels of background motion support, the methodologies presented in this paper provide an excellent comparison. All three modules are fully operational in flight.

The effect of emergent features on judgments of quantity in configural and separable displays.

PubMed

Peebles, David

2008-06-01

Two experiments investigated effects of emergent features on perceptual judgments of comparative magnitude in three diagrammatic representations: kiviat charts, bar graphs, and line graphs. Experiment 1 required participants to compare individual values; whereas in Experiment 2 participants had to integrate several values to produce a global comparison. In Experiment 1, emergent features of the diagrams resulted in significant distortions of magnitude judgments, each related to a common geometric illusion. Emergent features are also widely believed to underlie the general superiority of configural displays, such as kiviat charts, for tasks requiring the integration of information. Experiment 2 tested the extent of this benefit using diagrams with a wide range of values. Contrary to the results of previous studies, the configural display produced the poorest performance compared to the more separable displays. Moreover, the pattern of responses suggests that kiviat users switched from an integration strategy to a sequential one depending on the shape of the diagram. The experiments demonstrate the powerful interaction between emergent visual properties and cognition and reveal limits to the benefits of configural displays for integration tasks. (c) 2008 APA, all rights reserved

Sequence Diversity Diagram for comparative analysis of multiple sequence alignments.

PubMed

Sakai, Ryo; Aerts, Jan

2014-01-01

The sequence logo is a graphical representation of a set of aligned sequences, commonly used to depict conservation of amino acid or nucleotide sequences. Although it effectively communicates the amount of information present at every position, this visual representation falls short when the domain task is to compare between two or more sets of aligned sequences. We present a new visual presentation called a Sequence Diversity Diagram and validate our design choices with a case study. Our software was developed using the open-source program called Processing. It loads multiple sequence alignment FASTA files and a configuration file, which can be modified as needed to change the visualization. The redesigned figure improves on the visual comparison of two or more sets, and it additionally encodes information on sequential position conservation. In our case study of the adenylate kinase lid domain, the Sequence Diversity Diagram reveals unexpected patterns and new insights, for example the identification of subgroups within the protein subfamily. Our future work will integrate this visual encoding into interactive visualization tools to support higher level data exploration tasks.

New Bedform Phase Diagrams and Discriminant Functions for Formative Conditions of Bedforms in Open-Channel Flows

NASA Astrophysics Data System (ADS)

Ohata, Koji; Naruse, Hajime; Yokokawa, Miwa; Viparelli, Enrica

2017-11-01

Understanding of the formative conditions of fluvial bedforms is significant for both river management and geological studies. Diagrams showing bedform stability conditions have been widely used for the analyses of sedimentary structures. However, the use of discriminants to determine the boundaries of different bedforms regimes has not yet been explored. In this study, we use discriminant functions to describe formative conditions for a range of fluvial bedforms in a 3-D dimensionless parametric space. We do this by means of discriminant analysis using the Mahalanobis distance. We analyzed 3,793 available laboratory and field data and used these to produce new bedform phase diagrams. These diagrams employ three dimensionless parameters representing properties of flow hydraulics and sediment particles as their axes. The discriminant functions for bedform regimes proposed herein are quadratic functions of three dimensionless parameters and are expressed as curved surfaces in 3-D space. These empirical functions can be used to estimate paleoflow velocities from sedimentary structures. As an example of the reconstruction of hydraulic conditions, we calculated the paleoflow velocity of the 2011 Tohoku-Oki tsunami backwash flow from the sedimentary structures of the tsunami deposit. In so doing, we successfully reconstructed reasonable values of the paleoflow velocities.

Numerical-experimental observation of shape bistability of red blood cells flowing in a microchannel

NASA Astrophysics Data System (ADS)

Guckenberger, Achim; Kihm, Alexander; John, Thomas; Wagner, Christian; Gekle, Stephan

Red blood cells flowing through capillaries assume a wide variety of different shapes owing to their high deformability. Predicting the realized shapes is a complex field as they are determined by the intricate interplay between the flow conditions and the membrane mechanics. In this work we construct the shape phase diagram of a single red blood cell with a physiological viscosity ratio flowing in a microchannel. We use both experimental in-vitro measurements as well as 3D numerical simulations to complement the respective other one. Numerically, we have easy control over the initial starting configuration and natural access to the full 3D shape. With this information we obtain the phase diagram as a function of initial position, starting shape and cell velocity. Experimentally, we measure the occurrence frequency of the different shapes as a function of the cell velocity to construct the experimental diagram which is in good agreement with the numerical observations. Two different major shapes are found, namely croissants and slippers. Notably, both shapes show coexistence at low (<1 mm/s) and high velocities (>3 mm/s) while in-between only croissants are stable. This pronounced bistability indicates that RBC shapes are not only determined by system parameters such as flow velocity or channel size, but also strongly depend on the initial conditions.

On-line metabolic pathway analysis based on metabolic signal flow diagram.

PubMed

Shi, H; Shimizu, K

In this work, an integrated modeling approach based on a metabolic signal flow diagram and cellular energetics was used to model the metabolic pathway analysis for the cultivation of yeast on glucose. This approach enables us to make a clear analysis of the flow direction of the carbon fluxes in the metabolic pathways as well as of the degree of activation of a particular pathway for the synthesis of biomaterials for cell growth. The analyses demonstrate that the main metabolic pathways of Saccharomyces cerevisiae change significantly during batch culture. Carbon flow direction is toward glycolysis to satisfy the increase of requirement for precursors and energy. The enzymatic activation of TCA cycle seems to always be at normal level, which may result in the overflow of ethanol due to its limited capacity. The advantage of this approach is that it adopts both virtues of the metabolic signal flow diagram and the simple network analysis method, focusing on the investigation of the flow directions of carbon fluxes and the degree of activation of a particular pathway or reaction loop. All of the variables used in the model equations were determined on-line; the information obtained from the calculated metabolic coefficients may result in a better understanding of cell physiology and help to evaluate the state of the cell culture process. Copyright 1998 John Wiley & Sons, Inc.

30 CFR 57.11053 - Escape and evacuation plans.

Code of Federal Regulations, 2013 CFR

2013-07-01

... from the date of the last review. The plan shall include: (a) Mine maps or diagrams showing directions of principal air flow, location of escape routes and locations of existing telephones, primary fans... maps or diagrams shall be posted at all shaft stations and in underground shops, lunchrooms, and...

30 CFR 57.11053 - Escape and evacuation plans.

Code of Federal Regulations, 2014 CFR

2014-07-01

... from the date of the last review. The plan shall include: (a) Mine maps or diagrams showing directions of principal air flow, location of escape routes and locations of existing telephones, primary fans... maps or diagrams shall be posted at all shaft stations and in underground shops, lunchrooms, and...

30 CFR 57.11053 - Escape and evacuation plans.

Code of Federal Regulations, 2011 CFR

2011-07-01

... from the date of the last review. The plan shall include: (a) Mine maps or diagrams showing directions of principal air flow, location of escape routes and locations of existing telephones, primary fans... maps or diagrams shall be posted at all shaft stations and in underground shops, lunchrooms, and...

30 CFR 57.11053 - Escape and evacuation plans.

Code of Federal Regulations, 2012 CFR

2012-07-01

... from the date of the last review. The plan shall include: (a) Mine maps or diagrams showing directions of principal air flow, location of escape routes and locations of existing telephones, primary fans... maps or diagrams shall be posted at all shaft stations and in underground shops, lunchrooms, and...

30 CFR 57.11053 - Escape and evacuation plans.

Code of Federal Regulations, 2010 CFR

2010-07-01

... from the date of the last review. The plan shall include: (a) Mine maps or diagrams showing directions of principal air flow, location of escape routes and locations of existing telephones, primary fans... maps or diagrams shall be posted at all shaft stations and in underground shops, lunchrooms, and...

Performance back-deduction from a loading to flow coefficient map: Application to radial turbine

NASA Astrophysics Data System (ADS)

Carbonneau, Xavier; Binder, Nicolas

2012-12-01

Radial turbine stages are often used for applications requiring off-design operation, as turbocharging for instance. The off-design ability of such stages is commonly analyzed through the traditional turbine map, plotting the reduced mass-flow against the pressure-ratio, for reduced-speed lines. However, some alternatives are possible, such as the flow-coefficient ( Ψ) to loading-coefficient ( φ) diagram where the pressure-ratio lines are actually straight lines, very convenient property to perform prediction. A robust method re-creating this map from a predicted Ψ-φ diagram is needed. Recent work has shown that this back-deduction quality, without the use of any loss models, depends on the knowledge of an intermediate pressure-ratio. A modelization of this parameter is then proposed. The comparison with both experimental and CFD results is presented, with quite good agreement for mass flow rate and rotational speed, and for the intermediate pressure ratio. The last part of the paper is dedicated to the application of the intermediate pressure-ratio knowledge to the improvement of the deduction of the pressure ratio lines in the Ψ-φ diagram. Beside this improvement, the back-deduction method of the classical map is structured, applied and evaluated.

Flow diagram or prose: does the format of practice guidelines matter?

PubMed

Hardern, R D; Hodgson, L C; Hamer, D W

1998-06-01

The aim of this study was to compare the performance of two formats (prose and flow diagram) of the guidelines for management of paracetamol poisoning, and to assess the likely performance without access to the guidelines. A prospective questionnaire study of the management of seven hypothetical cases of paracetamol ingestion was carried out by accident and emergency senior house officers at a regional induction course. No differences were found between the two formats. The proportion of correct answers was 37% in the flow diagram and 31% in the prose group (95% confidence interval for the difference -8% to 20%). In the group with neither format of the guideline the proportion of correct answers was lower: 19% (95% confidence interval for the difference between this group and the group with flow charts 6.9% to 30.6%, for the difference between this group and the group with the prose format 0.4% to 24.8%). The time taken to answer the questions did not vary between the groups. These data do not support the exclusive use of either format. They suggest that management of paracetamol poisoning is less likely to be correct if staff do not have access to the guidelines.

Shear-induced crystallization of a dense rapid granular flow: hydrodynamics beyond the melting point.

PubMed

Khain, Evgeniy; Meerson, Baruch

2006-06-01

We investigate shear-induced crystallization in a very dense flow of monodisperse inelastic hard spheres. We consider a steady plane Couette flow under constant pressure and neglect gravity. We assume that the granular density is greater than the melting point of the equilibrium phase diagram of elastic hard spheres. We employ a Navier-Stokes hydrodynamics with constitutive relations all of which (except the shear viscosity) diverge at the crystal-packing density, while the shear viscosity diverges at a smaller density. The phase diagram of the steady flow is described by three parameters: an effective Mach number, a scaled energy loss parameter, and an integer number m: the number of half-oscillations in a mechanical analogy that appears in this problem. In a steady shear flow the viscous heating is balanced by energy dissipation via inelastic collisions. This balance can have different forms, producing either a uniform shear flow or a variety of more complicated, nonlinear density, velocity, and temperature profiles. In particular, the model predicts a variety of multilayer two-phase steady shear flows with sharp interphase boundaries. Such a flow may include a few zero-shear (solidlike) layers, each of which moving as a whole, separated by fluidlike regions. As we are dealing with a hard sphere model, the granulate is fluidized within the "solid" layers: the granular temperature is nonzero there, and there is energy flow through the boundaries of the solid layers. A linear stability analysis of the uniform steady shear flow is performed, and a plausible bifurcation diagram of the system, for a fixed m, is suggested. The problem of selection of m remains open.

Slot configuration for axial-flow turbomachinery blades

NASA Technical Reports Server (NTRS)

Taylor, W. E.

1972-01-01

Machining of slot in turbine blades of axial flow turbines to provide flow path between pressure and suction surfaces is discussed. Slot configuration and improvements in blade performance are described. Diagram of blade slot to show geometry of modification is included.

Computer studies of baroclinic flow. [Atmospheric General Circulation Experiment

NASA Technical Reports Server (NTRS)

Gall, R.

1985-01-01

Programs necessary for computing the transition curve on the regime diagram for the atmospheric general circulation experiment (AGOE) were completed and used to determine the regime diagram for the rotating annulus and some axisymmetric flows for one possible AGOE configuration. The effect of geometrical constraints on the size of eddies developing from a basic state is being examined. In AGOE, the geometric constraint should be the width of the shear zone or the baroclinic zone. Linear and nonlinear models are to be used to examine both barotropic and baroclinic flows. The results should help explain the scale selection mechanism of baroclinic eddies in the atmosphere experimental models such as AGOE, and the multiple vortex phenomenon in tornadoes.

Getting With It: Flow Diagrams

ERIC Educational Resources Information Center

Ritchie, W. A.

1975-01-01

The use of flow charts in the teaching of college mathematics enhances students' understanding of mathematical processes. Used appropriately in elementary and secondary schools they could also nurture understanding of algorithms. (SD)

Flow Effects on the Flammability Diagrams of Solid Fuels: Microgravity Influence on Ignition Delay

NASA Technical Reports Server (NTRS)

Cordova, J. L.; Walther, D. C.; Fernandez-Pello, A. C.; Steinhaus, T.; Torero, J. L.; Quintere, J. G.; Ross, H. D.

1999-01-01

The possibility of an accidental fire in space-based facilities is a primary concern of space exploration programs. Spacecraft environments generally present low velocity air currents produced by ventilation and heating systems (of the order of 0.1 m/s), and fluctuating oxygen concentrations around that of air due to CO2 removal systems. Recent experiments of flame spread in microgravity show the spread rate to be faster and the limiting oxygen concentration lower than in normal-gravity. To date, there is not a material flammability-testing protocol that specifically addresses issues related to microgravity conditions. The present project (FIST) aims to establish a testing methodology that is suitable for the specific conditions of reduced gravity. The concepts underlying the operation of the LIFT apparatus, ASTM-E 1321-93, have been used to develop the Forced-flow Ignition and flame-Spread Test (FIST). As in the LIFT, the FIST is used to obtain the flammability diagrams of the material, i.e., graphs of ignition delay time and flame spread rate as a function of the externally applied radiant flux, but under forced flow rather than natural convection conditions, and for different oxygen concentrations. Although the flammability diagrams are similar, the flammability properties obtained with the FIST are found to depend on the flow characteristics. A research program is currently underway with the purpose of implementing the FIST as a protocol to characterize the flammability performance of solid materials to be used in microgravity facilities. To this point, tests have been performed with the FIST apparatus in both normal-gravity and microgravity conditions to determine the effects of oxidizer flow characteristics on the flammability diagrams of polymethylmethacrylate (PMMA) fuel samples. The experiments are conducted at reduced gravity in a KC- 135 aircraft following a parabolic flight trajectory that provides up to 25 seconds of low gravity. The objective of the experiments is to obtain data of ignition delay and flame spread rate at low flow velocities (0.1 to 0.2 m/s), which cannot be obtained under normal gravity because of the natural convection induced flows (approx. 0.5 m/s). Due to the limited reduced gravity time, the data can only be obtained for high radiant fluxes, and are consequently limited in scope. These tests do, however, provide insight into the flammability diagram characteristics at low velocity and reduced gravity, and also into the implications of the flow-dependence of the flammability properties under environments similar to those encountered in space facilities.

Storage requirements for Georgia streams

USGS Publications Warehouse

Carter, Robert F.

1983-01-01

The suitability of a stream as a source of water supply or for waste disposal may be severely limited by low flow during certain periods. A water user may be forced to provide storage facilities to supplement the natural flow if the low flow is insufficient for his needs. This report provides data for evaluating the feasibility of augmenting low streamflow by means of storage facilities. It contains tabular data on storage requirements for draft rates that are as much as 60 percent of the mean annual flow at 99 continuous-record gaging stations, and draft-storage diagrams for estimating storage requirements at many additional sites. Through analyses of streamflow data, the State was divided into four regions. Draft-storage diagrams for each region provide a means of estimating storage requirements for sites on streams where data are scant, provided the drainage area, mean annual flow, and the 7-day, 10-year low flow are known or can be estimated. These data are tabulated for the 99 gaging stations used in the analyses and for 102 partial-record sites where only base-flow measurements have been made. The draft-storage diagrams are useful not only for estimating in-channel storage required for low-flow augmentation, but also can be used for estimating the volume of off-channel storage required to retain wastewater during low-flow periods for later release. In addition, these relationships can be helpful in estimating the volume of wastewater to be disposed of by spraying on land, provided that the water disposed of in this manner is only that for which streamflow dilution water is not currently available. Mean annual flow can be determined for any stream within the State by using the runoff map in this report. Low-flow indices can be estimated by several methods, including correlation of base-flow measurements with concurrent flow at nearby continuous-record gaging stations where low-flow indices have been determined.

Stochastic fundamental diagram for probabilistic traffic flow modeling.

DOT National Transportation Integrated Search

2011-09-01

Flowing water in river, transported gas or oil in pipe, electric current in wire, moving : goods on conveyor, molecular motors in living cell, and driving vehicles on a highway are : various kinds of flow from physical or non-physical systems, yet ea...

CHARACTERISTICS OF SOLAR MERIDIONAL FLOWS DURING SOLAR CYCLE 23

DOE Office of Scientific and Technical Information (OSTI.GOV)

Basu, Sarbani; Antia, H. M., E-mail: sarbani.basu@yale.ed, E-mail: antia@tifr.res.i

2010-07-01

We have analyzed available full-disk data from the Michelson Doppler Imager on board SOHO using the 'ring diagram' technique to determine the behavior of solar meridional flows over solar cycle 23 in the outer 2% of the solar radius. We find that the dominant component of meridional flows during solar maximum was much lower than that during the minima at the beginning of cycles 23 and 24. There were differences in the flow velocities even between the two minima. The meridional flows show a migrating pattern with higher-velocity flows migrating toward the equator as activity increases. Additionally, we find thatmore » the migrating pattern of the meridional flow matches those of sunspot butterfly diagram and the zonal flows in the shallow layers. A high-latitude band in meridional flow appears around 2004, well before the current activity minimum. A Legendre polynomial decomposition of the meridional flows shows that the latitudinal pattern of the flow was also different during the maximum as compared to that during the two minima. The different components of the flow have different time dependences, and the dependence is different at different depths.« less

Meridional Flow Measurements: Comparisons Between Ring Diagram Analysis and Fourier-Hankel Analysis

NASA Astrophysics Data System (ADS)

Zaatri, A.; Roth, M.

2008-09-01

The meridional circulation is a weak flow with amplitude in the order of 10 m/s on the solar surface. As this flow could be responsible for the transport of magnetic flux during the solar cycle it has become a crucial ingredient in some dynamo models. However, only less is known about the overall structure of the meridional circulation. Helioseismology is able to provide information on the structure of this flow in the solar interior. One widely used helioseismic technique for measuring frequency shifts due to horizontal flows in the subsurface layers of the sun is the ring diagram analyis (Corbard et al. 2003). It is based on the analysis of frequency shifts in the solar oscillation power spectrum as a function of the orientation of the wave vector. This then allows drawing conclusions on the strength of meridional flow, too. Ring diagram analysis is currently limited to the analysis of the wave field in only a small region on the solar surface. Consequently, information on the solar interior can only be inferred down to a depth of about 16 Mm. Another helioseismology method that promises to estimate the meridional flow strength down to greater depths is the Fourier-Hankel analysis (Krieger et al. 2007). This technique is based on a decomposition of the wave field in poleward and equatorward propagating waves. A possible frequency shift between them is then due to the meridional flow. We have been motivated for carrying out a comparative study between the two techniques to measure the meridional flow. We investigate the degree of coherence between the two methods by analyzing the same data sets recorded by the SOHO-MDI and GONG instruments.

Selective Attentional Effects of Textbook Study Questions on Student Learning in Science.

ERIC Educational Resources Information Center

Holliday, William G.

1981-01-01

Reports results of a study testing a selective attentional model which predicted that textbook study questions adjunct to a flow diagram will focus students' attention more upon questioned information and less upon nonquestioned information. A picture-word diagram describing biogeochemical cycles to high school biology students (N=176) was used.…

Overprompting Science Students Using Adjunct Study Questions.

ERIC Educational Resources Information Center

Holliday, William G.

Described is an investigation of the hypothesis that students presented with strong hints or prompts to answers of comprehension questions adjunct to a flow diagram would understand less than students presented with no prompts. Also described is the study of the hypotheses that a diagram-only treatment group would outperform the prompted group and…

33 CFR 159.57 - Installation, operation, and maintenance instructions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... complete parts list. (5) A schematic diagram showing the relative location of each part. (6) A wiring diagram. (7) A description of the service that may be performed by the user without coming into contact with sewage or chemicals. (8) Average and peak capacity of the device for the flow rate, volume, or...

The Interpersonal Conflict Episode: A Systems Model.

ERIC Educational Resources Information Center

Slawski, Carl

A detailed systems diagram elaborates the process of dealing with a single conflict episode between two parties or persons. Hypotheses are fully stated to lead the reader through the flow diagram. A concrete example illustrates its use. Detail is provided in an accounting scheme of virtually all possible variables to consider in analyzing a…

33 CFR 159.57 - Installation, operation, and maintenance instructions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... complete parts list. (5) A schematic diagram showing the relative location of each part. (6) A wiring diagram. (7) A description of the service that may be performed by the user without coming into contact with sewage or chemicals. (8) Average and peak capacity of the device for the flow rate, volume, or...

33 CFR 159.57 - Installation, operation, and maintenance instructions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... complete parts list. (5) A schematic diagram showing the relative location of each part. (6) A wiring diagram. (7) A description of the service that may be performed by the user without coming into contact with sewage or chemicals. (8) Average and peak capacity of the device for the flow rate, volume, or...

Computer programs for axial flow compressor design

NASA Technical Reports Server (NTRS)

Carmody, R. H.; Creveling, H. F.

1969-01-01

Four computer programs examine effects of design parameters and indicate areas for research of multistage axial flow compressors. The programs provide information on velocity diagrams and stage-by-stage performance calculation, radial equilibrium of flow, radial distribution of total pressure, and off-design performance calculation.

A Jamming Phase Diagram for Pressing Polymers

NASA Astrophysics Data System (ADS)

Teng, Chao; Zhang, Zexin; Wang, Xiaoliang; Xue, Gi; Nanjing University Team; Soochow University Collaboration

2011-03-01

Molecular glasses begin to flow when they are heated. Other glassy systems, such as dense foams, emulsions, colloidal suspensions and granular materials, begin to flow when subjected to sufficiently large stresses. The equivalence of these two routes to flow is a basic tenet of jamming, a conceptual means of unifying glassy behavior in a swath of disordered, dynamical arrested systems. However, a full understanding of jamming transition for polymers remains elusive. By controlling the packing densities of polymer glasses, we found that polymer glasses could once flow under cold-pressing at temperatures well below its calorimetric glass transition temperature (Tg). The thermomechanical analysis (TMA) results confirmed that Tg changed with density as well as the applied stress, which is exactly what to be expected within the jamming picture. We propose a jamming phase diagram for polymers based on our laboratory experiments.

Physiomodel - an integrative physiology in Modelica.

PubMed

Matejak, Marek; Kofranek, Jiri

2015-08-01

Physiomodel (http://www.physiomodel.org) is our reimplementation and extension of an integrative physiological model called HumMod 1.6 (http://www.hummod.org) using our Physiolibrary (http://www.physiolibrary.org). The computer language Modelica is well-suited to exactly formalize integrative physiology. Modelica is an equation-based, and object-oriented language for hybrid ordinary differential equations (http:// www.modelica.org). Almost every physiological term can be defined as a class in this language and can be instantiated as many times as it occurs in the body. Each class has a graphical icon for use in diagrams. These diagrams are self-describing; the Modelica code generated from them is the full representation of the underlying mathematical model. Special Modelica constructs of physical connectors from Physiolibrary allow us to create diagrams that are analogies of electrical circuits with Kirchhoff's laws. As electric currents and electric potentials are connected in electrical domain, so are molar flows and concentrations in the chemical domain; volumetric flows and pressures in the hydraulic domain; flows of heat energy and temperatures in the thermal domain; and changes and amounts of members in the population domain.

EVOLUTION OF NEAR-SURFACE FLOWS INFERRED FROM HIGH-RESOLUTION RING-DIAGRAM ANALYSIS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bogart, Richard S.; Baldner, Charles S.; Basu, Sarbani

2015-07-10

Ring-diagram analysis of acoustic waves observed at the photosphere can provide a relatively robust determination of the sub-surface flows at a particular time under a particular region. The depth of penetration of the waves is related to the size of the region, hence the depth extent of the measured flows is inversely proportional to the spatial resolution. Most ring-diagram analysis has focused on regions of extent ∼15° (180 Mm) or more in order to provide reasonable mode sets for inversions. Helioseismic and Magnetic Imager (HMI) data analysis also provides a set of ring fit parameters on a scale three timesmore » smaller. These provide flow estimates for the outer 1% (7 Mm) of the Sun only, with very limited depth resolution, but with spatial resolution adequate to map structures potentially associated with the belts and regions of magnetic activity. There are a number of systematic effects affecting the determination of flows from a local helioseismic analysis of regions over different parts of the observable disk, and not all of them are well understood. In this study we characterize those systematic effects with higher spatial resolution so that they may be accounted for more effectively in mapping the temporal and spatial evolution of the flows. Leaving open the question of the mean structure of the global meridional circulation and the differential rotation, we describe the near-surface flow anomalies in time and latitude corresponding to the torsional oscillation pattern in differential rotation and analogous patterns in the meridional cell structure as observed by the Solar Dynamics Observatory/HMI.« less

In situ laser-induced photochemical silver substrate synthesis and sequential SERS detection in a flow cell.

PubMed

Herman, Krisztian; Szabó, László; Leopold, Loredana F; Chiş, Vasile; Leopold, Nicolae

2011-05-01

A new, simple, and effective approach for multianalyte sequential surface-enhanced Raman scattering (SERS) detection in a flow cell is reported. The silver substrate was prepared in situ by laser-induced photochemical synthesis. By focusing the laser on the 320 μm inner diameter glass capillary at 0.5 ml/min continuous flow of 1 mM silver nitrate and 10 mM sodium citrate mixture, a SERS active silver spot on the inner wall of the glass capillary was prepared in a few seconds. The test analytes, dacarbazine, 4-(2-pyridylazo)resorcinol (PAR) complex with Cu(II), and amoxicillin, were sequentially injected into the flow cell. Each analyte was adsorbed to the silver surface, enabling the recording of high intensity SERS spectra even at 2 s integration times, followed by desorption from the silver surface and being washed away from the capillary. Before and after each analyte passed the detection window, citrate background spectra were recorded, and thus, no "memory effects" perturbed the SERS detection. A good reproducibility of the SERS spectra obtained under flow conditions was observed. The laser-induced photochemically synthesized silver substrate enables high Raman enhancement, is characterized by fast preparation with a high success rate, and represents a valuable alternative for silver colloids as SERS substrate in flow approaches.

40 CFR 60.276a - Recordkeeping and reporting requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

... device, and continuous monitoring equipment; (4) Flow diagram of process and emission capture equipment... at values exceeding ±15 percent of the value established under § 60.274a(c) or operation at flow...

40 CFR 60.276 - Recordkeeping and reporting requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

...; (4) Flow diagram of process and emission capture equipment including other equipment or process(es... values exceeding ±15 percent of the value established under § 60.274(c) or operation at flow rates lower...

40 CFR 60.276 - Recordkeeping and reporting requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

...; (4) Flow diagram of process and emission capture equipment including other equipment or process(es... values exceeding ±15 percent of the value established under § 60.274(c) or operation at flow rates lower...

40 CFR 60.276 - Recordkeeping and reporting requirements.

Code of Federal Regulations, 2012 CFR

2012-07-01

...; (4) Flow diagram of process and emission capture equipment including other equipment or process(es... values exceeding ±15 percent of the value established under § 60.274(c) or operation at flow rates lower...

40 CFR 60.276a - Recordkeeping and reporting requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

... device, and continuous monitoring equipment; (4) Flow diagram of process and emission capture equipment... at values exceeding ±15 percent of the value established under § 60.274a(c) or operation at flow...

40 CFR 60.276a - Recordkeeping and reporting requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

... device, and continuous monitoring equipment; (4) Flow diagram of process and emission capture equipment... at values exceeding ±15 percent of the value established under § 60.274a(c) or operation at flow...

40 CFR 60.276a - Recordkeeping and reporting requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... device, and continuous monitoring equipment; (4) Flow diagram of process and emission capture equipment... at values exceeding ±15 percent of the value established under § 60.274a(c) or operation at flow...

40 CFR 60.276 - Recordkeeping and reporting requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

...; (4) Flow diagram of process and emission capture equipment including other equipment or process(es... values exceeding ±15 percent of the value established under § 60.274(c) or operation at flow rates lower...

40 CFR 60.276a - Recordkeeping and reporting requirements.

Code of Federal Regulations, 2012 CFR

2012-07-01

... device, and continuous monitoring equipment; (4) Flow diagram of process and emission capture equipment... at values exceeding ±15 percent of the value established under § 60.274a(c) or operation at flow...

40 CFR 60.276 - Recordkeeping and reporting requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

...; (4) Flow diagram of process and emission capture equipment including other equipment or process(es... values exceeding ±15 percent of the value established under § 60.274(c) or operation at flow rates lower...

Identifying High-Rate Flows Based on Sequential Sampling

NASA Astrophysics Data System (ADS)

Zhang, Yu; Fang, Binxing; Luo, Hao

We consider the problem of fast identification of high-rate flows in backbone links with possibly millions of flows. Accurate identification of high-rate flows is important for active queue management, traffic measurement and network security such as detection of distributed denial of service attacks. It is difficult to directly identify high-rate flows in backbone links because tracking the possible millions of flows needs correspondingly large high speed memories. To reduce the measurement overhead, the deterministic 1-out-of-k sampling technique is adopted which is also implemented in Cisco routers (NetFlow). Ideally, a high-rate flow identification method should have short identification time, low memory cost and processing cost. Most importantly, it should be able to specify the identification accuracy. We develop two such methods. The first method is based on fixed sample size test (FSST) which is able to identify high-rate flows with user-specified identification accuracy. However, since FSST has to record every sampled flow during the measurement period, it is not memory efficient. Therefore the second novel method based on truncated sequential probability ratio test (TSPRT) is proposed. Through sequential sampling, TSPRT is able to remove the low-rate flows and identify the high-rate flows at the early stage which can reduce the memory cost and identification time respectively. According to the way to determine the parameters in TSPRT, two versions of TSPRT are proposed: TSPRT-M which is suitable when low memory cost is preferred and TSPRT-T which is suitable when short identification time is preferred. The experimental results show that TSPRT requires less memory and identification time in identifying high-rate flows while satisfying the accuracy requirement as compared to previously proposed methods.

Distal end side-to-side anastomoses of sequential vein graft to small target coronary arteries improve intraoperative graft flow

PubMed Central

2014-01-01

Background End-to-side anastomoses to connect the distal end of the great saphenous vein (GSV) to small target coronary arteries are commonly performed in sequential coronary artery bypass grafting (CABG). However, the oversize diameter ratio between the GSV and small target vessels at end-to-side anastomoses might induce adverse hemodynamic condition. The purpose of this study was to describe a distal end side-to-side anastomosis technique and retrospectively compare the effect of distal end side-to-side versus end-to-side anastomosis on graft flow characteristics. Methods We performed side-to-side anastomoses to connect the distal end of the GSV to small target vessels on 30 patients undergoing off-pump sequential CABG in our hospital between October 2012 and July 2013. Among the 30 patients, end-to-side anastomoses at the distal end of the GSV were initially performed on 14 patients; however, due to poor graft flow, those anastomoses were revised into side-to-side anastomoses. We retrospectively compared the intraoperative graft flow characteristics of the end-to-side versus side-to-side anastomoses in the 14 patients. The patient outcomes were also evaluated. Results We found that the side-to-side anastomosis reconstruction improved intraoperative flow and reduced pulsatility index in all the 14 patients significantly. The 16 patients who had the distal end side-to-side anastomoses performed directly also exhibited satisfactory intraoperative graft flow. Three-month postoperative outcomes for all the patients were satisfactory. Conclusions Side-to-side anastomosis at the distal end of sequential vein grafts might be a promising strategy to connect small target coronary arteries to the GSV. PMID:24884776

Software Methodology Catalog. Second Edition. Revision

DTIC Science & Technology

1989-03-01

structured design involve characterization of the data flow through graphical representation, identification of the various transform elements, assembling...and graphical diagrams to facilitate communication within the team. The diagrams are consistent with the design language and can be automatically...organization, box structure graphics provide a visual means of client communication. These box structures are used during analysis and design to review

The Two-By-Two Array: An Aid in Conceptualization and Problem Solving

ERIC Educational Resources Information Center

Eberhart, James

2004-01-01

The fields of mathematics, science, and engineering are replete with diagrams of many varieties. They range in nature from the Venn diagrams of symbolic logic to the Periodic Chart of the Elements; and from the fault trees of risk assessment to the flow charts used to describe laboratory procedures, industrial processes, and computer programs. All…

Microcomputer Applications in Interaction Analysis.

ERIC Educational Resources Information Center

Wadham, Rex A.

The Timed Interval Categorical Observation Recorder (TICOR), a portable, battery powered microcomputer designed to automate the collection of sequential and simultaneous behavioral observations and their associated durations, was developed to overcome problems in gathering subtle interaction analysis data characterized by sequential flow of…

The Use of Flow Charts in Sediment Routing Analysis

Treesearch

Leslie M. Reid

1982-01-01

Flow charts are a widely used means of diagramming relationships among transport processes and storage sites during analyses of sediment routing. Because they have taken so many different forms, however, it is very difficult to use published flow charts to compare geomorphic systems. Though they generally are constructed to achieve the same purpose, flow charts...

Bellows flow-induced vibrations

NASA Technical Reports Server (NTRS)

Tygielski, P. J.; Smyly, H. M.; Gerlach, C. R.

1983-01-01

The bellows flow excitation mechanism and results of comprehensive test program are summarized. The analytical model for predicting bellows flow induced stress is refined. The model includes the effects of an upstream elbow, arbitrary geometry, and multiple piles. A refined computer code for predicting flow induced stress is described which allows life prediction if a material S-N diagram is available.

Assessing Learning Styles of Graduate Entry Nursing Students as a Classroom Research Activity: A quantitative research study.

PubMed

Gonzales, Lucia K; Glaser, Dale; Howland, Lois; Clark, Mary Jo; Hutchins, Susie; Macauley, Karen; Close, Jacqueline F; Leveque, Noelle Lipkin; Failla, Kim Reina; Brooks, Raelene; Ward, Jillian

2017-01-01

A number of studies across different disciplines have investigated students' learning styles. Differences are known to exist between graduate and baccalaureate nursing students. However, few studies have investigated the learning styles of students in graduate entry nursing programs. . Study objective was to describe graduate entry nursing students' learning styles. A descriptive design was used for this study. The Index of Learning Styles (ILS) was administered to 202 graduate entry nursing student volunteers at a southwestern university. Descriptive statistics, tests of association, reliability, and validity were performed. Graduate nursing students and faculty participated in data collection, analysis, and dissemination of the results. Predominant learning styles were: sensing - 82.7%, visual - 78.7%, sequential - 65.8%, and active - 59.9%. Inter-item reliabilities for the postulated subscales were: sensing/intuitive (α=0.70), visual/verbal (α=0.694), sequential/global (α=0.599), and active/reflective (α=0.572). Confirmatory factor analysis for results of validity were: χ 2 (896)=1110.25, p<0.001, CFI=0.779, TLI=0.766, WRMR=1.14, and RMSEA =0.034. Predominant learning styles described students as being concrete thinkers oriented toward facts (sensing); preferring pictures, diagrams, flow charts, demonstrations (visual); being linear thinkers (sequencing); and enjoying working in groups and trying things out (active),. The predominant learning styles suggest educators teach concepts through simulation, discussion, and application of knowledge. Multiple studies, including this one, provided similar psychometric results. Similar reliability and validity results for the ILS have been noted in previous studies and therefore provide sufficient evidence to use the ILS with graduate entry nursing students. This study provided faculty with numerous opportunities for actively engaging students in data collection, analysis, and dissemination of results. Copyright © 2016 Elsevier Ltd. All rights reserved.

Changes in transthoracic impedance during sequential biphasic defibrillation.

PubMed

Deakin, Charles D; Ambler, Jonathan J S; Shaw, Steven

2008-08-01

Sequential monophasic defibrillation reduces transthoracic impedance (TTI) and progressively increases current flow for any given energy level. The effect of sequential biphasic shocks on TTI is unknown. We therefore studied patients undergoing elective cardioversion using a biphasic waveform to establish whether this is a phenomenon seen in the clinical setting. Adults undergoing elective DC cardioversion for atrial flutter or fibrillation received sequential transthoracic shocks using an escalating protocol (70J, 100J, 150J, 200J, and 300J) with a truncated exponential biphasic waveform. TTI was calculated through the defibrillator circuit and recorded electronically. Successful cardioversion terminated further defibrillation shocks. A total of 58 patients underwent elective cardioversion. Cardioversion was successful in 93.1% patients. First shock TTI was 92.2 [52.0-126.0]Omega (n=58) and decreased significantly with each sequential shock. Mean TTI in patients receiving five shocks (n=5) was 85.0Omega. Sequential biphasic defibrillation decreases TTI in a similar manner to that seen with monophasic waveforms. The effect is likely during defibrillation during cardiac arrest by the quick succession in which shocks are delivered and the lack of cutaneous blood flow which limits the inflammatory response. The ability of biphasic defibrillators to adjust their waveform according to TTI is likely to minimise any effect of these findings on defibrillation efficacy.

Design of Multistage Axial-Flow Compressors

NASA Technical Reports Server (NTRS)

Crouse, J. E.; Gorrell, W. T.

1983-01-01

Program developed for computing aerodynamic design of multistage axialflow compressor and associated blading geometry input for internal flow analysis. Aerodynamic solution gives velocity diagrams on selected streamlines of revolution at blade row edges. Program written in FORTRAN IV.

Research on external flow field of a car based on reverse engineering

NASA Astrophysics Data System (ADS)

Hu, Shushan; Liu, Ronge

2018-05-01

In this paper, the point cloud data of FAW-VOLKSWAGEN car body shape is obtained by three coordinate measuring instrument and laser scanning method. The accurate three dimensional model of the car is obtained using CATIA software reverse modelling technology. The car body is gridded, the calculation field and boundary condition type of the car flow field are determined, and the numerical simulation is carried out in Hyper Mesh software. The pressure cloud diagram, velocity vector diagram, air resistance coefficient and lift coefficient of the car are obtained. The calculation results reflect the aerodynamic characteristics of the car's external flow field. The motion of the separation flow on the surface of the vehicle body is well simulated, and the area where the vortex motion is relatively intense has been determined. The results provide a theoretical basis for improving and optimizing the body shape.

Analysis of user equilibrium for staggered shifts in a single-entry traffic corridor with no late arrivals

NASA Astrophysics Data System (ADS)

Li, Chuan-Yao; Huang, Hai-Jun; Tang, Tie-Qiao

2017-05-01

In this paper, we investigate the effects of staggered shifts on the user equilibrium (UE) state in a single-entry traffic corridor with no late arrivals from the analytical and numerical perspective. The LWR (Lighthill-Whitham-Richards) model and the Greenshields' velocity-density function are used to describe the dynamic properties of traffic flow. Propositions for the properties of flow patterns in UE, and the quasi-analytic solutions for three possible situations in UE are deduced. Numerical tests are carried out to testify the analytical results, where the three-dimensional evolution diagram of traffic flow illustrates that shock and rarefaction wave exist in UE and the space-time diagram indicates that UE solutions satisfy the propagation properties of traffic flow. In addition, the cost curves show that the UE solutions satisfy the UE trip-timing condition.

Computer code for preliminary sizing analysis of axial-flow turbines

NASA Technical Reports Server (NTRS)

Glassman, Arthur J.

1992-01-01

This mean diameter flow analysis uses a stage average velocity diagram as the basis for the computational efficiency. Input design requirements include power or pressure ratio, flow rate, temperature, pressure, and rotative speed. Turbine designs are generated for any specified number of stages and for any of three types of velocity diagrams (symmetrical, zero exit swirl, or impulse) or for any specified stage swirl split. Exit turning vanes can be included in the design. The program output includes inlet and exit annulus dimensions, exit temperature and pressure, total and static efficiencies, flow angles, and last stage absolute and relative Mach numbers. An analysis is presented along with a description of the computer program input and output with sample cases. The analysis and code presented herein are modifications of those described in NASA-TN-D-6702. These modifications improve modeling rigor and extend code applicability.

Phased charging and discharging in capacitive desalinatio

DOEpatents

Stadermann, Michael; Qu, Yatian; Santiago, Juan G.; Hemmatifar, Ali

2017-09-12

A system combines complete, ultra-thin cells into a monolithic and robust framework necessary for desalination applications which yields orders of magnitude faster desalination. The electrode pairs are located so that a flow of feed water flows through or around the electrode pairs with the flow perpendicular to sequentially applied electric potentials. The system is controlled to charge the series of electrode pairs sequentially or phased. That means the charging of the second electrode pair is delayed with regard to the charging of the first electrode pair and the charging of a third electrode pair is delayed with respect to the charging of the second electrode pair.

Selection of a rigid internal fixation construct for stabilization at the craniovertebral junction in pediatric patients.

PubMed

Anderson, Richard C E; Ragel, Brian T; Mocco, J; Bohman, Leif-Erik; Brockmeyer, Douglas L

2007-07-01

Atlantoaxial and occipitocervical instability in children have traditionally been treated with posterior bone and wire fusion and external halo orthoses. Recently, successful outcomes have been achieved using rigid internal fixation, particularly C1-2 transarticular screws. The authors describe flow diagrams created to help clinicians determine which method of internal fixation to use in complex anatomical circumstances when bilateral transarticular screw placement is not possible. The records of children who underwent either atlantoaxial or occipitocervical fixation with rigid internal fixation over an 11-year period were retrospectively reviewed to define flow diagrams used to determine treatment protocols. Among the 95 patients identified who underwent atlantoaxial or occipitocervical fixation, the craniocervical anatomy in 25 patients (six atlantoaxial and 19 occipitocervical fixations [26%]) required alternative methods of internal fixation. Types of screw fixation included loop or rod constructs anchored by combinations of C1-2 transarticular screws (15 constructs), C-1 lateral mass screws (11), C-2 pars screws (24), C-2 translaminar screws (one), and subaxial lateral mass screws (six). The mean age of the patients (15 boys and 10 girls) was 9.8 years (range 1.3-17 years). All 22 patients with greater than 3-month follow-up duration achieved solid bone fusion and maintained stable constructs on radiographic studies. Clinical improvement was seen in all patients who had preoperative symptoms. Novel flow diagrams are suggested to help guide selection of rigid internal fixation constructs when performing pediatric C1-2 and occipitocervical stabilizations. Use of these flow diagrams has led to successful fusion in 25 pediatric patients with difficult anatomy requiring less common constructs.

Methods for studying medical device technology and practitioner cognition: the case of user-interface issues with infusion pumps.

PubMed

Schraagen, Jan Maarten; Verhoeven, Fenne

2013-02-01

The aims of this study were to investigate how a variety of research methods is commonly employed to study technology and practitioner cognition. User-interface issues with infusion pumps were selected as a case because of its relevance to patient safety. Starting from a Cognitive Systems Engineering perspective, we developed an Impact Flow Diagram showing the relationship of computer technology, cognition, practitioner behavior, and system failure in the area of medical infusion devices. We subsequently conducted a systematic literature review on user-interface issues with infusion pumps, categorized the studies in terms of methods employed, and noted the usability problems found with particular methods. Next, we assigned usability problems and related methods to the levels in the Impact Flow Diagram. Most study methods used to find user interface issues with infusion pumps focused on observable behavior rather than on how artifacts shape cognition and collaboration. A concerted and theory-driven application of these methods when testing infusion pumps is lacking in the literature. Detailed analysis of one case study provided an illustration of how to apply the Impact Flow Diagram, as well as how the scope of analysis may be broadened to include organizational and regulatory factors. Research methods to uncover use problems with technology may be used in many ways, with many different foci. We advocate the adoption of an Impact Flow Diagram perspective rather than merely focusing on usability issues in isolation. Truly advancing patient safety requires the systematic adoption of a systems perspective viewing people and technology as an ensemble, also in the design of medical device technology. Copyright © 2012 Elsevier Inc. All rights reserved.

Sequential geophysical and flow inversion to characterize fracture networks in subsurface systems

DOE PAGES

Mudunuru, Maruti Kumar; Karra, Satish; Makedonska, Nataliia; ...

2017-09-05

Subsurface applications, including geothermal, geological carbon sequestration, and oil and gas, typically involve maximizing either the extraction of energy or the storage of fluids. Fractures form the main pathways for flow in these systems, and locating these fractures is critical for predicting flow. However, fracture characterization is a highly uncertain process, and data from multiple sources, such as flow and geophysical are needed to reduce this uncertainty. We present a nonintrusive, sequential inversion framework for integrating data from geophysical and flow sources to constrain fracture networks in the subsurface. In this framework, we first estimate bounds on the statistics formore » the fracture orientations using microseismic data. These bounds are estimated through a combination of a focal mechanism (physics-based approach) and clustering analysis (statistical approach) of seismic data. Then, the fracture lengths are constrained using flow data. In conclusion, the efficacy of this inversion is demonstrated through a representative example.« less

Sequential geophysical and flow inversion to characterize fracture networks in subsurface systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mudunuru, Maruti Kumar; Karra, Satish; Makedonska, Nataliia

Subsurface applications, including geothermal, geological carbon sequestration, and oil and gas, typically involve maximizing either the extraction of energy or the storage of fluids. Fractures form the main pathways for flow in these systems, and locating these fractures is critical for predicting flow. However, fracture characterization is a highly uncertain process, and data from multiple sources, such as flow and geophysical are needed to reduce this uncertainty. We present a nonintrusive, sequential inversion framework for integrating data from geophysical and flow sources to constrain fracture networks in the subsurface. In this framework, we first estimate bounds on the statistics formore » the fracture orientations using microseismic data. These bounds are estimated through a combination of a focal mechanism (physics-based approach) and clustering analysis (statistical approach) of seismic data. Then, the fracture lengths are constrained using flow data. In conclusion, the efficacy of this inversion is demonstrated through a representative example.« less

Wettability and Flow Rate Impacts on Immiscible Displacement: A Theoretical Model

NASA Astrophysics Data System (ADS)

Hu, Ran; Wan, Jiamin; Yang, Zhibing; Chen, Yi-Feng; Tokunaga, Tetsu

2018-04-01

When a more viscous fluid displaces a less viscous one in porous media, viscous pressure drop stabilizes the displacement front against capillary pressure fluctuation. For this favorable viscous ratio conditions, previous studies focused on the front instability under slow flow conditions but did not address competing effects of wettability and flow rate. Here we study how this competition controls displacement patterns. We propose a theoretical model that describes the crossover from fingering to stable flow as a function of invading fluid contact angle θ and capillary number Ca. The phase diagram predicted by the model shows that decreasing θ stabilizes the displacement for θ≥45° and the critical contact angle θc increases with Ca. The boundary between corner flow and cooperative filling for θ < 45° is also described. This work extends the classic phase diagram and has potential applications in predicting CO2 capillary trapping and manipulating wettability to enhance gas/oil displacement efficiency.

The Seepage Simulation of Single Hole and Composite Gas Drainage Based on LB Method

NASA Astrophysics Data System (ADS)

Chen, Yanhao; Zhong, Qiu; Gong, Zhenzhao

2018-01-01

Gas drainage is the most effective method to prevent and solve coal mine gas power disasters. It is very important to study the seepage flow law of gas in fissure coal gas. The LB method is a simplified computational model based on micro-scale, especially for the study of seepage problem. Based on fracture seepage mathematical model on the basis of single coal gas drainage, using the LB method during coal gas drainage of gas flow numerical simulation, this paper maps the single-hole drainage gas, symmetric slot and asymmetric slot, the different width of the slot combined drainage area gas flow under working condition of gas cloud of gas pressure, flow path diagram and flow velocity vector diagram, and analyses the influence on gas seepage field under various working conditions, and also discusses effective drainage method of the center hole slot on both sides, and preliminary exploration that is related to the combination of gas drainage has been carried on as well.

Dynamical properties of nematic liquid crystals subjected to shear flow and magnetic fields: tumbling instability and nonequilibrium fluctuations.

PubMed

Fatriansyah, Jaka Fajar; Orihara, Hiroshi

2013-07-01

We investigate the dynamical properties of monodomain nematic liquid crystals under shear flow and magnetic fields on the basis of the Ericksen-Leslie theory. Stable and unstable states appear depending on the magnetic field and the shear rate. The trajectory of the unstable state shows tumbling motion. The phase diagram of these states is plotted as a function of the three components of the magnetic field at a constant shear rate. The phase diagram changes depending on the viscous properties of different types of nematic liquid crystals. In this nonequilibrium steady state, we calculate the correlation function of director fluctuations and the response function, and discuss the nonequilibrium fluctuations and the modified fluctuation-dissipation relation in connection with nonconservative forces due to shear flow.

Self assembly of oppositely charged latex particles at oil-water interface.

PubMed

Nallamilli, Trivikram; Ragothaman, Srikanth; Basavaraj, Madivala G

2017-01-15

In this study we explore the self assembly of oppositely charged latex particles at decane water interfaces. Two spreading protocols have been proposed in this context. In the first method oppositely charged particles are mixed prior to spreading at the interface, this is called "premixed-mixtures". In the second protocol negatively charged particles are first spread at the interface at known coverage followed by spreading positively charged particles at known coverage and this is called "sequential-mixtures". In premixed mixtures depending on particle mixing ratio (composition) and total surface coverage a number of 2d structures ranging from 2d crystals, aggregate-crystal coexistence and 2d-gels are observed. A detailed phase diagram of this system has been explored. In sequential-mixtures for the first time we observed a new phase in colloidal monolayers called 2d-bi crystalline domains. These structures consisted regions of two crystal phases of oppositely charged particles separated by a one dimensional chain of alternating positive and negative particles. Phase diagram of this system has also been explored at various combinations of first spread and second spread particles. A possible mechanism leading to formation of these 2d bi crystalline structures has been discussed. A direct visualization of breakage and reformation of particle barriers separating the crystal phases has been demonstrated through videos. Effect of salt in the water sub phase and particle hydrophobicity on domain formation is also investigated. Copyright © 2016 Elsevier Inc. All rights reserved.

A Babcock-Leighton Solar Dynamo Model with Multi-cellular Meridional Circulation in Advection- and Diffusion-dominated Regimes

NASA Astrophysics Data System (ADS)

Belucz, Bernadett; Dikpati, Mausumi; Forgács-Dajka, Emese

2015-06-01

Babcock-Leighton type-solar dynamo models with single-celled meridional circulation are successful in reproducing many solar cycle features. Recent observations and theoretical models of meridional circulation do not indicate a single-celled flow pattern. We examine the role of complex multi-cellular circulation patterns in a Babcock-Leighton solar dynamo in advection- and diffusion-dominated regimes. We show from simulations that the presence of a weak, second, high-latitude reverse cell speeds up the cycle and slightly enhances the poleward branch in the butterfly diagram, whereas the presence of a second cell in depth reverses the tilt of the butterfly wing to an antisolar type. A butterfly diagram constructed from the middle of convection zone yields a solar-like pattern, but this may be difficult to realize in the Sun because of magnetic buoyancy effects. Each of the above cases behaves similarly in higher and lower magnetic diffusivity regimes. However, our dynamo with a meridional circulation containing four cells in latitude behaves distinctly differently in the two regimes, producing solar-like butterfly diagrams with fast cycles in the higher diffusivity regime, and complex branches in butterfly diagrams in the lower diffusivity regime. We also find that dynamo solutions for a four-celled pattern, two in radius and two in latitude, prefer to quickly relax to quadrupolar parity if the bottom flow speed is strong enough, of similar order of magnitude as the surface flow speed.

A BABCOCK–LEIGHTON SOLAR DYNAMO MODEL WITH MULTI-CELLULAR MERIDIONAL CIRCULATION IN ADVECTION- AND DIFFUSION-DOMINATED REGIMES

DOE Office of Scientific and Technical Information (OSTI.GOV)

Belucz, Bernadett; Forgács-Dajka, Emese; Dikpati, Mausumi, E-mail: bbelucz@astro.elte.hu, E-mail: dikpati@ucar.edu

Babcock–Leighton type-solar dynamo models with single-celled meridional circulation are successful in reproducing many solar cycle features. Recent observations and theoretical models of meridional circulation do not indicate a single-celled flow pattern. We examine the role of complex multi-cellular circulation patterns in a Babcock–Leighton solar dynamo in advection- and diffusion-dominated regimes. We show from simulations that the presence of a weak, second, high-latitude reverse cell speeds up the cycle and slightly enhances the poleward branch in the butterfly diagram, whereas the presence of a second cell in depth reverses the tilt of the butterfly wing to an antisolar type. A butterflymore » diagram constructed from the middle of convection zone yields a solar-like pattern, but this may be difficult to realize in the Sun because of magnetic buoyancy effects. Each of the above cases behaves similarly in higher and lower magnetic diffusivity regimes. However, our dynamo with a meridional circulation containing four cells in latitude behaves distinctly differently in the two regimes, producing solar-like butterfly diagrams with fast cycles in the higher diffusivity regime, and complex branches in butterfly diagrams in the lower diffusivity regime. We also find that dynamo solutions for a four-celled pattern, two in radius and two in latitude, prefer to quickly relax to quadrupolar parity if the bottom flow speed is strong enough, of similar order of magnitude as the surface flow speed.« less

The Argon Geochronology Experiment (AGE)

NASA Technical Reports Server (NTRS)

Swindle, T. D.; Bode, R.; Fennema, A.; Chutjian, A.; MacAskill, J. A.; Darrach, M. R.; Clegg, S. M.; Wiens, R. C.; Cremers, D.

2006-01-01

This viewgraph presentation reviews the Argon Geochronology Experiment (AGE). Potassium-Argon dating is shown along with cosmic ray dating exposure. The contents include a flow diagram of the Argon Geochronology Experiment, and schematic diagrams of the mass spectrometer vacuum system, sample manipulation mechanism, mineral heater oven, and the quadrupole ion trap mass spectrometer. The Laser-Induced Breakdown Spectroscopy (LIBS) Operation with elemental abundances is also described.

Seminar on Understanding Digital Control and Analysis in Vibration Test Systems

NASA Technical Reports Server (NTRS)

1975-01-01

The advantages of the digital methods over the analog vibration methods are demonstrated. The following topics are covered: (1) methods of computer-controlled random vibration and reverberation acoustic testing, (2) methods of computer-controlled sinewave vibration testing, and (3) methods of computer-controlled shock testing. General algorithms are described in the form of block diagrams and flow diagrams.

The Role of Diagrammatic Respresentation in Learning Sequences, Identification and Classification as a Function of Verbal and Spatial Ability.

ERIC Educational Resources Information Center

Winn, William

1982-01-01

Results of this study suggest that diagrams provide different types of information for ninth-grade students (N=273) and that learners process each type differently. Flow diagrams running across a page from either left to right or right to left, or with or without drawings of dinosaurs, were used. (JN)

40 CFR 60.697 - Recordkeeping requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

... be kept. (i) Detailed schematics, and piping and instrumentation diagrams. (ii) The dates and... flow and volatile organic compound content under varying liquid level conditions (dynamic and static... vent stream composition, constituent concentrations, flow rate, relative humidity, and temperature. The...

40 CFR 60.697 - Recordkeeping requirements.

Code of Federal Regulations, 2012 CFR

2012-07-01

... specifications shall be kept. (i) Detailed schematics, and piping and instrumentation diagrams. (ii) The dates..., including flow and volatile organic compound content under varying liquid level conditions (dynamic and... vent stream composition, constituent concentrations, flow rate, relative humidity, and temperature. The...

40 CFR 60.697 - Recordkeeping requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

... be kept. (i) Detailed schematics, and piping and instrumentation diagrams. (ii) The dates and... flow and volatile organic compound content under varying liquid level conditions (dynamic and static... vent stream composition, constituent concentrations, flow rate, relative humidity, and temperature. The...

Transportable Maps Software. Volume I.

DTIC Science & Technology

1982-07-01

being collected at the beginning or end of the routine. This allows the interaction to be followed sequentially through its steps by anyone reading the...flow is either simple sequential , simple conditional (the equivalent of ’if-then-else’), simple iteration (’DO-loop’), or the non-linear recursion...input raster images to be in the form of sequential binary files with a SEGMENTED record type. The advantage of this form is that large logical records

TrafficGen Architecture Document

DTIC Science & Technology

2016-01-01

sequence diagram ....................................................5 Fig. 5 TrafficGen traffic flows viewed in SDT3D...Scripts contain commands to have the network node listen on specific ports and flows describing the start time, stop time, and specific traffic ...arranged vertically and time presented horizontally. Individual traffic flows are represented by horizontal bars indicating the start time, stop time

Effect of speed matching on fundamental diagram of pedestrian flow

NASA Astrophysics Data System (ADS)

Fu, Zhijian; Luo, Lin; Yang, Yue; Zhuang, Yifan; Zhang, Peitong; Yang, Lizhong; Yang, Hongtai; Ma, Jian; Zhu, Kongjin; Li, Yanlai

2016-09-01

Properties of pedestrian may change along their moving path, for example, as a result of fatigue or injury, which has never been properly investigated in the past research. The paper attempts to study the speed matching effect (a pedestrian adjusts his velocity constantly to the average velocity of his neighbors) and its influence on the density-velocity relationship (a pedestrian adjust his velocity to the surrounding density), known as the fundamental diagram of the pedestrian flow. By the means of the cellular automaton, the simulation results fit well with the empirical data, indicating the great advance of the discrete model for pedestrian dynamics. The results suggest that the system velocity and flow rate increase obviously under a big noise, i.e., a diverse composition of pedestrian crowd, especially in the region of middle or high density. Because of the temporary effect, the speed matching has little influence on the fundamental diagram. Along the entire density, the relationship between the step length and the average pedestrian velocity is a piecewise function combined two linear functions. The number of conflicts reaches the maximum with the pedestrian density of 2.5 m-2, while decreases by 5.1% with the speed matching.

UPIOM: a new tool of MFA and its application to the flow of iron and steel associated with car production.

PubMed

Nakamura, Shinichiro; Kondo, Yasushi; Matsubae, Kazuyo; Nakajima, Kenichi; Nagasaka, Tetsuya

2011-02-01

Identification of the flow of materials and substances associated with a product system provides useful information for Life Cycle Analysis (LCA), and contributes to extending the scope of complementarity between LCA and Materials Flow Analysis/Substances Flow Analysis (MFA/SFA), the two major tools of industrial ecology. This paper proposes a new methodology based on input-output analysis for identifying the physical input-output flow of individual materials that is associated with the production of a unit of given product, the unit physical input-output by materials (UPIOM). While the Sankey diagram has been a standard tool for the visualization of MFA/SFA, with an increase in the complexity of the flows under consideration, which will be the case when economy-wide intersectoral flows of materials are involved, the Sankey diagram may become too complex for effective visualization. An alternative way to visually represent material flows is proposed which makes use of triangulation of the flow matrix based on degrees of fabrication. The proposed methodology is applied to the flow of pig iron and iron and steel scrap that are associated with the production of a passenger car in Japan. Its usefulness to identify a specific MFA pattern from the original IO table is demonstrated.

TV Trouble-Shooting Manual. Volumes 3-4. Part 1: Block Diagram of Colour TV Receiver and Signal Flow. Student and Instructor's Manuals.

ERIC Educational Resources Information Center

Mukai, Masaaki; Kobayashi, Ryozo

These volumes are, respectively, the self-instructional student manual and the teacher manual that cover the first set of training topics in this course for television repair technicians. Both volumes contain the following two sections: (1) Functional Block Diagram of a Colour TV Receiver, including information on the video reproduction circuit,…

Summary of Recent Inducer Testing at MSFC and Future Plans

NASA Technical Reports Server (NTRS)

Skelley, Stephen

2003-01-01

This viewgraph presentation covers water flow tests on the RS-83 Main LOX Inducer for the Space Shuttle Main Engine (SSME). The presentation lists recent water tests on the SSME liquid oxygen (LOX) pump inducer, includes images and diagrams of the water test facility at Marshall Space Flight Center (MSFC), profiles inducer hydrodynamic forces, and diagrams the performance of the RS-83 inducer.

Analysis of internal flow of J85-13 multistage compressor

NASA Technical Reports Server (NTRS)

Hager, R. D.

1977-01-01

Interstage data recorded on a J85-13 engine were used to analyze the internal flow of the compressor. Measured pressures and temperatures were used as input to a streamline analysis program to calculate the velocity diagrams at the inlet and outlet of each blade row. From the velocity diagrams and blade geometry, selected blade-element performance parameters were calculated. From the detailed analysis it is concluded that the compressor is probably hub critical (stall initiates at the hub) in the latter stages for the design speed conditions. As a result, the casing treatment over the blade tips has little or no effect on stall margin at design speed. Radial inlet distortion did not appear to change the flow in the stages that control stall because of the rapid attenuation of the distortion within the compressor.

Distinguishing high and low flow domains in urban drainage systems 2 days ahead using numerical weather prediction ensembles

NASA Astrophysics Data System (ADS)

Courdent, Vianney; Grum, Morten; Mikkelsen, Peter Steen

2018-01-01

Precipitation constitutes a major contribution to the flow in urban storm- and wastewater systems. Forecasts of the anticipated runoff flows, created from radar extrapolation and/or numerical weather predictions, can potentially be used to optimize operation in both wet and dry weather periods. However, flow forecasts are inevitably uncertain and their use will ultimately require a trade-off between the value of knowing what will happen in the future and the probability and consequence of being wrong. In this study we examine how ensemble forecasts from the HIRLAM-DMI-S05 numerical weather prediction (NWP) model subject to three different ensemble post-processing approaches can be used to forecast flow exceedance in a combined sewer for a wide range of ratios between the probability of detection (POD) and the probability of false detection (POFD). We use a hydrological rainfall-runoff model to transform the forecasted rainfall into forecasted flow series and evaluate three different approaches to establishing the relative operating characteristics (ROC) diagram of the forecast, which is a plot of POD against POFD for each fraction of concordant ensemble members and can be used to select the weight of evidence that matches the desired trade-off between POD and POFD. In the first approach, the rainfall input to the model is calculated for each of 25 ensemble members as a weighted average of rainfall from the NWP cells over the catchment where the weights are proportional to the areal intersection between the catchment and the NWP cells. In the second approach, a total of 2825 flow ensembles are generated using rainfall input from the neighbouring NWP cells up to approximately 6 cells in all directions from the catchment. In the third approach, the first approach is extended spatially by successively increasing the area covered and for each spatial increase and each time step selecting only the cell with the highest intensity resulting in a total of 175 ensemble members. While the first and second approaches have the disadvantage of not covering the full range of the ROC diagram and being computationally heavy, respectively, the third approach leads to both a broad coverage of the ROC diagram range at a relatively low computational cost. A broad coverage of the ROC diagram offers a larger selection of prediction skill to choose from to best match to the prediction purpose. The study distinguishes itself from earlier research in being the first application to urban hydrology, with fast runoff and small catchments that are highly sensitive to local extremes. Furthermore, no earlier reference has been found on the highly efficient third approach using only neighbouring cells with the highest threat to expand the range of the ROC diagram. This study provides an efficient and robust approach to using ensemble rainfall forecasts affected by bias and misplacement errors for predicting flow threshold exceedance in urban drainage systems.

The state diagram for cell adhesion under flow: leukocyte rolling and firm adhesion.

PubMed

Chang, K C; Tees, D F; Hammer, D A

2000-10-10

Leukocyte adhesion under flow in the microvasculature is mediated by binding between cell surface receptors and complementary ligands expressed on the surface of the endothelium. Leukocytes adhere to endothelium in a two-step mechanism: rolling (primarily mediated by selectins) followed by firm adhesion (primarily mediated by integrins). Using a computational method called "Adhesive Dynamics," we have simulated the adhesion of a cell to a surface in flow, and elucidated the relationship between receptor-ligand functional properties and the dynamics of adhesion. We express this relationship in a state diagram, a one-to-one map between the biophysical properties of adhesion molecules and various adhesive behaviors. Behaviors that are observed in simulations include firm adhesion, transient adhesion (rolling), and no adhesion. We varied the dissociative properties, association rate, bond elasticity, and shear rate and found that the unstressed dissociation rate, k(r)(o), and the bond interaction length, gamma, are the most important molecular properties controlling the dynamics of adhesion. Experimental k(r)(o) and gamma values from the literature for molecules that are known to mediate rolling adhesion fall within the rolling region of the state diagram. We explain why L-selectin-mediated rolling, which has faster k(r)(o) than other selectins, is accompanied by a smaller value for gamma. We also show how changes in association rate, shear rate, and bond elasticity alter the dynamics of adhesion. The state diagram (which must be mapped for each receptor-ligand system) presents a concise and comprehensive means of understanding the relationship between bond functional properties and the dynamics of adhesion mediated by receptor-ligand bonds.

Structural state diagram of concentrated suspensions of jammed soft particles in oscillatory shear flow

NASA Astrophysics Data System (ADS)

Khabaz, Fardin; Cloitre, Michel; Bonnecaze, Roger T.

2018-03-01

In a recent study [Khabaz et al., Phys. Rev. Fluids 2, 093301 (2017), 10.1103/PhysRevFluids.2.093301], we showed that jammed soft particle glasses (SPGs) crystallize and order in steady shear flow. Here we investigate the rheology and microstructures of these suspensions in oscillatory shear flow using particle-dynamics simulations. The microstructures in both types of flows are similar, but their evolutions are very different. In both cases the monodisperse and polydisperse suspensions form crystalline and layered structures, respectively, at high shear rates. The crystals obtained in the oscillatory shear flow show fewer defects compared to those in the steady shear. SPGs remain glassy for maximum oscillatory strains less than about the yield strain of the material. For maximum strains greater than the yield strain, microstructural and rheological transitions occur for SPGs. Polydisperse SPGs rearrange into a layered structure parallel to the flow-vorticity plane for sufficiently high maximum shear rates and maximum strains about 10 times greater than the yield strain. Monodisperse suspensions form a face-centered cubic (FCC) structure when the maximum shear rate is low and hexagonal close-packed (HCP) structure when the maximum shear rate is high. In steady shear, the transition from a glassy state to a layered one for polydisperse suspensions included a significant induction strain before the transformation. In oscillatory shear, the transformation begins to occur immediately and with different microstructural changes. A state diagram for suspensions in large amplitude oscillatory shear flow is found to be in close but not exact agreement with the state diagram for steady shear flow. For more modest amplitudes of around one to five times the yield strain, there is a transition from a glassy structure to FCC and HCP crystals, at low and high frequencies, respectively, for monodisperse suspensions. At moderate frequencies, the transition is from glassy to HCP via an intermediate FCC phase.

Stepwise flow diagram for the development of formulations of non spore-forming bacteria against foliar pathogens: The case of Lysobacter capsici AZ78.

PubMed

Segarra, Guillem; Puopolo, Gerardo; Giovannini, Oscar; Pertot, Ilaria

2015-12-20

The formulation is a significant step in biopesticide development and is an efficient way to obtain consistency in terms of biological control under field conditions. Nonetheless, there is still a lack of information regarding the processes needed to achieve efficient formulation of non spore-forming bacterial biological control agents. In response to this, we propose a flow diagram made up of six steps including selection of growth parameters, checking of minimum shelf life, selection of protective additives, checking that the additives have no adverse effects, validation of the additive mix under field conditions and choosing whether to use additives as co-formulants or tank mix additives. This diagram is intended to provide guidance and decision-making criteria for the formulation of non spore-forming bacterial biological control agents against foliar pathogens. The diagram was then validated by designing an efficient formulation for a Gram-negative bacterium, Lysobacter capsici AZ78, to control grapevine downy mildew caused by Plasmopara viticola. A harvest of 10(10)L. capsici AZ78cellsml(-1) was obtained in a bench top fermenter. The viability of cells decreased by only one order of magnitude after one year of storage at 4°C. The use of a combination of corn steep liquor, lignosulfonate, and polyethyleneglycol in the formulation improved the survival of L. capsici AZ78 cells living on grapevine leaves under field conditions by one order of magnitude. Furthermore, the use of these additives also guaranteed a reduction of 71% in P. viticola attacks. In conclusion, this work presents a straightforward stepwise flow diagram to help researchers develop formulations for biological control agents that are easy to prepare, stable, not phytotoxic and able to protect the microorganims under field conditions. Copyright © 2015 Elsevier B.V. All rights reserved.

Accessible Modelling of Complexity in Health (AMoCH) and associated data flows: asthma as an exemplar.

PubMed

Liyanage, Harshana; Luzi, Daniela; De Lusignan, Simon; Pecoraro, Fabrizio; McNulty, Richard; Tamburis, Oscar; Krause, Paul; Rigby, Michael; Blair, Mitch

2016-04-18

Background Modelling is an important part of information science. Models are abstractions of reality. We use models in the following contexts: (1) to describe the data and information flows in clinical practice to information scientists, (2) to compare health systems and care pathways, (3) to understand how clinical cases are recorded in record systems and (4) to model health care business models.Asthma is an important condition associated with a substantial mortality and morbidity. However, there are difficulties in determining who has the condition, making both its incidence and prevalence uncertain.Objective To demonstrate an approach for modelling complexity in health using asthma prevalence and incidence as an exemplar.Method The four steps in our process are:1. Drawing a rich picture, following Checkland's soft systems methodology;2. Constructing data flow diagrams (DFDs);3. Creating Unified Modelling Language (UML) use case diagrams to describe the interaction of the key actors with the system;4. Activity diagrams, either UML activity diagram or business process modelling notation diagram.Results Our rich picture flagged the complexity of factors that might impact on asthma diagnosis. There was consensus that the principle issue was that there were undiagnosed and misdiagnosed cases as well as correctly diagnosed. Genetic predisposition to atopy; exposure to environmental triggers; impact of respiratory health on earnings or ability to attend education or participate in sport, charities, pressure groups and the pharmaceutical industry all increased the likelihood of a diagnosis of asthma. Stigma and some factors within the health system diminished the likelihood of a diagnosis. The DFDs and other elements focused on better case finding.Conclusions This approach flagged the factors that might impact on the reported prevalence or incidence of asthma. The models suggested that applying selection criteria may improve the specificity of new or confirmed diagnosis.

40 CFR 264.1035 - Recordkeeping requirements.

Code of Federal Regulations, 2012 CFR

2012-07-01

...., temperatures, flow rates, or vent stream organic compounds and concentrations) that represent the conditions... the estimated or design flow rate and organic content of each vent stream and define the acceptable..., drawings, schematics, and piping and instrumentation diagrams based on the appropriate sections of “APTI...

40 CFR 264.1035 - Recordkeeping requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

...., temperatures, flow rates, or vent stream organic compounds and concentrations) that represent the conditions... the estimated or design flow rate and organic content of each vent stream and define the acceptable..., drawings, schematics, and piping and instrumentation diagrams based on the appropriate sections of “APTI...

40 CFR 264.1035 - Recordkeeping requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

...., temperatures, flow rates, or vent stream organic compounds and concentrations) that represent the conditions... the estimated or design flow rate and organic content of each vent stream and define the acceptable..., drawings, schematics, and piping and instrumentation diagrams based on the appropriate sections of “APTI...

40 CFR 265.1035 - Recordkeeping requirements.

Code of Federal Regulations, 2012 CFR

2012-07-01

...., temperatures, flow rates or vent stream organic compounds and concentrations) that represent the conditions... -include the estimated or design flow rate and organic content of each vent stream and define the..., drawings, schematics, and piping and instrumentation diagrams based on the appropriate sections of “APTI...

40 CFR 265.1035 - Recordkeeping requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

...., temperatures, flow rates or vent stream organic compounds and concentrations) that represent the conditions... -include the estimated or design flow rate and organic content of each vent stream and define the..., drawings, schematics, and piping and instrumentation diagrams based on the appropriate sections of “APTI...

40 CFR 264.1035 - Recordkeeping requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

...., temperatures, flow rates, or vent stream organic compounds and concentrations) that represent the conditions... the estimated or design flow rate and organic content of each vent stream and define the acceptable..., drawings, schematics, and piping and instrumentation diagrams based on the appropriate sections of “APTI...

40 CFR 265.1035 - Recordkeeping requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

...., temperatures, flow rates or vent stream organic compounds and concentrations) that represent the conditions... -include the estimated or design flow rate and organic content of each vent stream and define the..., drawings, schematics, and piping and instrumentation diagrams based on the appropriate sections of “APTI...

40 CFR 265.1035 - Recordkeeping requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

...., temperatures, flow rates or vent stream organic compounds and concentrations) that represent the conditions... -include the estimated or design flow rate and organic content of each vent stream and define the..., drawings, schematics, and piping and instrumentation diagrams based on the appropriate sections of “APTI...

Dark energy in the environments of the Local Group, the M 81 group, and the CenA group: the normalized Hubble diagram

NASA Astrophysics Data System (ADS)

Teerikorpi, P.; Chernin, A. D.; Karachentsev, I. D.; Valtonen, M. J.

2008-05-01

Context: Type Ia supernova observations on scales of thousands of Mpc show that the global expansion of the universe is accelerated by antigravity produced by the enigmatic dark energy contributing 3/4 of the total energy of the universe. Aims: Does antigravity act on small scales as well as large? As a continuation of our efforts to answer this crucial question we combine high accuracy observations of the galaxy flows around the Local Group and the nearby M 81 and CenA groups to observe the effect of the dark energy density on local scales of a few Mpc. Methods: We use an analytical model to describe non-uniform static space-time regions around galaxy groups. In this context it is useful to present the Hubble flow in a normalized Hubble diagram V/Hv Rv vs. r/R_v, where the vacuum Hubble constant Hv depends only on the cosmological vacuum density and the zero-gravity distance Rv depends on the vacuum density and on the mass of the galaxy group. We have prepared the normalized Hubble diagrams for the LG, M 81 and CenA group environments for different values of the assumed vacuum energy density, using a total of about 150 galaxies, for almost all of which the distances have been measured by the HST. Results: The normalized Hubble diagram, where we identify dynamically different regions, is in agreement with the standard vacuum density (Ωv = 0.77~h_70-2), the out-flow of galaxies clearly being controlled by the minimum energy condition imposed by the central mass plus the vacuum density. A high vacuum density 1.6~h_70-2 violates the minimum energy limit, while a low density 0.1~h_70-2 leaves the start of the Hubble flow around 1-2 Mpc with the slope close to the global value obscure. We also consider the subtle relation of the zero-gravity radius Rv to the zero-velocity distance R0 appearing in the usual retarded expansion around a mass M: in a vacuum-dominated flat universe R0 ≈ 0.76 R_v. Conclusions: The normalized Hubble diagram appears to be a good way to present and analyze physically different regions around mass clumps embedded in cosmological vacuum. The most natural interpretation of the diagram is that the local density of the dark energy is approximately equal to the density known from studies on global scales.

33. Photocopied 1983, from original drawing (DP49484), Picatinny Arsenal, November ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

33. Photocopied 1983, from original drawing (DP-49484), Picatinny Arsenal, November 29, 1948. 'SMOKELESS POWDER Area: REWORK POWDER PROCESS FLOW DIAGRAM.' THE PROCESS DETAILED IN THIS DIAGRAM FROM THE POACHING HOUSE TO THE PACK HOUSE IS SUBSTANTIALLY THE SAME AS THE ONE FOR PRODUCING NEW POWDER FROM NITRATED COTTON. - Picatinny Arsenal, 500 Area, Powder Factory & Power House, State Route 15 near I-80, Dover, Morris County, NJ

Improving the Useability of the Defense Mapping Agency Digital Feature Analysis Data for Training Simulator Applications.

DTIC Science & Technology

1982-09-01

would be merged and a corrected output tape could be generated to 21 I 47 be used as a replacement for the original tape. A diagram of the system designed...overview of all of the procedures involved In an error correction session. The process flow is depicted in the configuration diagram provided in Figure... Roundhouse . .. ....................... 224 Roads (General) ......................... 240 Elevated. .... ...................... 244 Causeways

A Predictive Model for Submarine Canyon Type Based on the Relative Influence of Rivers, Waves and Tides.

NASA Astrophysics Data System (ADS)

Sumner, E.; Paull, C. K.

2017-12-01

In recent years progress has been achieved in directly measuring turbidity currents in submarine canyons and channels. It is useful to consider how representative these observations are of the diversity that potentially exists in the dynamics of turbidity currents among different canyons and channels. Firstly, we integrate sediment core, bathymetric and (in a limited number of cases) direct observations of turbidity current dynamics from 20 submarine canyons on the northern California Margin. We use this dataset to construct a diagram that explains canyon type, and thus turbidity current characteristics (grain-size carried, flow power, relative frequency of flows), based on the relative influence of rivers, waves and tides at the canyon head. This diagram enables prediction of canyon type and thus processes using three easily measurable characteristics: (i) distance of the canyon head from the shoreline; (ii) distance of the canyon head from the nearest river mouth; and (iii) local shelf width. Secondly, we test and refine the diagram using published data on submarine canyons from around the world. We also discuss the influence of outsized events such as earthquakes on submarine canyons. Finally, we demonstrate the location within the diagram of current monitoring studies and thus suggest where it might be fruitful to focus future monitoring efforts.

Application of machine learning and expert systems to Statistical Process Control (SPC) chart interpretation

NASA Technical Reports Server (NTRS)

Shewhart, Mark

1991-01-01

Statistical Process Control (SPC) charts are one of several tools used in quality control. Other tools include flow charts, histograms, cause and effect diagrams, check sheets, Pareto diagrams, graphs, and scatter diagrams. A control chart is simply a graph which indicates process variation over time. The purpose of drawing a control chart is to detect any changes in the process signalled by abnormal points or patterns on the graph. The Artificial Intelligence Support Center (AISC) of the Acquisition Logistics Division has developed a hybrid machine learning expert system prototype which automates the process of constructing and interpreting control charts.

Effect of sequential pneumatic compression therapy on venous blood velocity, refilling time, pain and quality of life in women with varicose veins: a randomized control study

PubMed Central

Yamany, Abeer; Hamdy, Bassant

2016-01-01

[Purpose] The aim of this study was to investigate the effects of sequential pneumatic compression therapy on venous blood flow, refilling time, pain level, and quality of life in women with varicose veins. [Subjects and Methods] Twenty-eight females with varicose veins were selected and randomly allocated to a control group, and experimental group. Maximum and mean venous blood velocities, the refilling time, pain by visual analog scale and quality of life by Aberdeen Varicose Veins Questionnaire were measured in all patients before and after six weeks of treatment. Both groups received lower extremity exercises; in addition, patients in the experimental group received sequential pneumatic compression therapy for 30 minutes daily, five days a week for six weeks. [Results] All measured parameters improved significantly in both groups, comparison of post treatment measurements between groups showed that the maximum and mean blood flow velocity, the pain level, and quality of life were significantly higher in the experimental group compared with the control group. On the other hand there was no significant difference between groups for refilling time. [Conclusion] Sequential pneumatic compression therapy with the applied parameters was an effective modality for increasing venous blood flow, reducing pain, and improving quality of women life with varicose veins. PMID:27512247

Density profiles of the exclusive queuing process

NASA Astrophysics Data System (ADS)

Arita, Chikashi; Schadschneider, Andreas

2012-12-01

The exclusive queuing process (EQP) incorporates the exclusion principle into classic queuing models. It is characterized by, in addition to the entrance probability α and exit probability β, a third parameter: the hopping probability p. The EQP can be interpreted as an exclusion process of variable system length. Its phase diagram in the parameter space (α,β) is divided into a convergent phase and a divergent phase by a critical line which consists of a curved part and a straight part. Here we extend previous studies of this phase diagram. We identify subphases in the divergent phase, which can be distinguished by means of the shape of the density profile, and determine the velocity of the system length growth. This is done for EQPs with different update rules (parallel, backward sequential and continuous time). We also investigate the dynamics of the system length and the number of customers on the critical line. They are diffusive or subdiffusive with non-universal exponents that also depend on the update rules.

Control and measurement of the phase behavior of aqueous solutions using microfluidics

PubMed Central

Shim, Jung-uk; Cristobal, Galder; Link, Darren R.; Thorsen, Todd; Jia, Yanwei; Piattelli, Katie; Fraden, Seth

2008-01-01

A microfluidic device denoted the Phase Chip has been designed to measure and manipulate the phase diagram of multi-component fluid mixtures. The Phase Chip exploits the permeation of water through poly(dimethylsiloxane) (PDMS) in order to controllably vary the concentration of solutes in aqueous nanoliter volume microdrops stored in wells. The permeation of water in the Phase Chip is modeled using the diffusion equation and good agreement between experiment and theory is obtained. The Phase Chip operates by first creating drops of the water/solute mixture whose composition varies sequentially. Next, drops are transported down channels and guided into storage wells using surface tension forces. Finally, the solute concentration of each stored drop is simultaneously varied and measured. Two applications of the Phase Chip are presented. First, the phase diagram of a polymer/salt mixture is measured on-chip and validated off-chip and second, protein crystallization rates are enhanced through the manipulation of the kinetics of nucleation and growth. PMID:17580868

Phase diagram of Ag-Pd bimetallic nanoclusters by molecular dynamics simulations: solid-to-liquid transition and size-dependent behavior.

PubMed

Kim, Da Hye; Kim, Hyun You; Ryu, Ji Hoon; Lee, Hyuck Mo

2009-07-07

This report on the solid-to-liquid transition region of an Ag-Pd bimetallic nanocluster is based on a constant energy microcanonical ensemble molecular dynamics simulation combined with a collision method. By varying the size and composition of an Ag-Pd bimetallic cluster, we obtained a complete solid-solution type of binary phase diagram of the Ag-Pd system. Irrespective of the size and composition of the cluster, the melting temperature of Ag-Pd bimetallic clusters is lower than that of the bulk state and rises as the cluster size and the Pd composition increase. Additionally, the slope of the phase boundaries (even though not exactly linear) is lowered when the cluster size is reduced on account of the complex relations of the surface tension, the bulk melting temperature, and the heat of fusion. The melting of the cluster initially starts at the surface layer. The initiation and propagation of a five-fold icosahedron symmetry is related to the sequential melting of the cluster.

Application of the Methods of Gas Dynamics to Water Flows with Free Surface II : Flows with Momentum Discontinuities (hydraulic Jumps)

NASA Technical Reports Server (NTRS)

Preiswerk, Ernst

1940-01-01

In this paper an introduction to shock polar diagrams is given which then leads into an examination of water depths in hydraulic jumps. Energy loss during these jumps is considered along with an extended look at elementary solutions of flow. An experimental test set-up is described and the results presented.

Experimental Investigation of Reynolds Number Effects on Test Quality in a Hypersonic Expansion Tube

NASA Astrophysics Data System (ADS)

Rossmann, Tobias; Devin, Alyssa; Shi, Wen; Verhoog, Charles

2017-11-01

Reynolds number effects on test time and the temporal and spatial flow quality in a hypersonic expansion tube are explored using high-speed pressure, infrared optical, and Schlieren imaging measurements. Boundary layer models for shock tube flows are fairly well established to assist in the determination of test time and flow dimensions at typical high enthalpy test conditions. However, the application of these models needs to be more fully explored due to the unsteady expansion of turbulent boundary layers and contact regions separating dissimilar gasses present in expansion tube flows. Additionally, expansion tubes rely on the development of a steady jet with a large enough core-flow region at the exit of the acceleration tube to create a constant velocity region inside of the test section. High-speed measurements of pressure and Mach number at several locations within the expansion tube allow for the determination of an experimental x-t diagram. The comparison of the experimentally determined x-t diagram to theoretical highlights the Reynolds number dependent effects on expansion tube. Additionally, spatially resolved measurements of the Reynolds number dependent, steady core-flow in the expansion tube viewing section are shown. NSF MRI CBET #1531475, Lafayette College, McCutcheon Foundation.

Design and performance of a large vocabulary discrete word recognition system. Volume 2: Appendixes. [flow charts and users manual

NASA Technical Reports Server (NTRS)

1973-01-01

The users manual for the word recognition computer program contains flow charts of the logical diagram, the memory map for templates, the speech analyzer card arrangement, minicomputer input/output routines, and assembly language program listings.

Three-dimensional vesicles under shear flow: numerical study of dynamics and phase diagram.

PubMed

Biben, Thierry; Farutin, Alexander; Misbah, Chaouqi

2011-03-01

The study of vesicles under flow, a model system for red blood cells (RBCs), is an essential step in understanding various intricate dynamics exhibited by RBCs in vivo and in vitro. Quantitative three-dimensional analyses of vesicles under flow are presented. The regions of parameters to produce tumbling (TB), tank-treating, vacillating-breathing (VB), and even kayaking (or spinning) modes are determined. New qualitative features are found: (i) a significant widening of the VB mode region in parameter space upon increasing shear rate γ and (ii) a robustness of normalized period of TB and VB with γ. Analytical support is also provided. We make a comparison with existing experimental results. In particular, we find that the phase diagram of the various dynamics depends on three dimensionless control parameters, while a recent experimental work reported that only two are sufficient.

The Interlibrary Loan Transaction

PubMed Central

Pings, Vern M.

1965-01-01

Although the number of items borrowed through interlibrary loan may not increase as dramatically as it has in the past ten years, the trend can be expected to continue because of the growing interdisciplinary nature of biomedical research and because of the anticipated improved bibliographic control of biomedical literature. To provide a framework for collecting data on volume of flow between institutions, on time requirements for processing operations, on cost of interlibrary transactions, on the efficiency of communication channels, and on alternative procedures for performing the transaction, block diagrams were prepared to show the flow of information and materials between individuals and institutions. These diagrams show the interinstitutional dependence; any alterations in procedures in one institution affect other institutions. Even though it can be clearly shown where alterations in the flow pattern can be effected, there are little quantitative data available to serve as a justification for maintaining or modifying existing procedures. PMID:14271114

A source flow characteristic technique for the analysis of scramjet exhaust flow field

NASA Technical Reports Server (NTRS)

Delguidice, P.; Dash, S.; Kalben, P.

1974-01-01

The factors which influence the design and selection of a nozzle for a hypersonic scramjet are described. A two dimensional second-order characteristic procedure capable of analyzing the aerodynamic performance of typical nozzle configurations is presented. Equations of motion governing the two dimensional, axisymmetric, or axially expanding inviscid flow of a gas mixture, with frozen chemistry, are provided. Diagrams of the flow conditions for various configurations are included.

30 CFR 250.154 - What identification signs must I display?

Code of Federal Regulations, 2014 CFR

2014-07-01

... number of the facility location as depicted on OCS Official Protraction Diagrams or leasing maps; (iii...; and (3) For subsea wells that flow individually into separate pipelines, affix the required sign on... receiving platform. For multiple subsea wells that flow into a common pipeline or pipelines, no sign is...

10 CFR 205.322 - Contents of application.

Code of Federal Regulations, 2014 CFR

2014-01-01

... diagrams which provide clarification of any of the above items should be included. (2) A general area map... conductor ratings; (ii) System power flow plots for the applicant's service area for heavy summer and light... is scheduled to be placed in service and for the fifth year thereafter. The power flow plots...

40 CFR 721.91 - Computation of estimated surface water concentrations: Instructions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... shall be computed for each site using the stream flow rate appropriate for the site according to... computing the equation, the number of kilograms released, and receiving stream flow. (a) Number of kilograms... diagram which describes each manufacturing, processing, or use operation involving the substance. The...

10 CFR 205.322 - Contents of application.

Code of Federal Regulations, 2012 CFR

2012-01-01

... diagrams which provide clarification of any of the above items should be included. (2) A general area map... conductor ratings; (ii) System power flow plots for the applicant's service area for heavy summer and light... is scheduled to be placed in service and for the fifth year thereafter. The power flow plots...

17 CFR 229.1103 - (Item 1103) Transaction summary and risk factors.

Code of Federal Regulations, 2012 CFR

2012-04-01

... if doing so will aid understanding. Consider using diagrams to illustrate the relationships among the parties, the structure of the securities offered (including, for example, the flow of funds or any... securities may be issued. (v) Identify the distribution frequency on the securities. (vi) Summarize the flow...

40 CFR 721.91 - Computation of estimated surface water concentrations: Instructions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... shall be computed for each site using the stream flow rate appropriate for the site according to... computing the equation, the number of kilograms released, and receiving stream flow. (a) Number of kilograms... diagram which describes each manufacturing, processing, or use operation involving the substance. The...

17 CFR 229.1103 - (Item 1103) Transaction summary and risk factors.

Code of Federal Regulations, 2013 CFR

2013-04-01

... if doing so will aid understanding. Consider using diagrams to illustrate the relationships among the parties, the structure of the securities offered (including, for example, the flow of funds or any... securities may be issued. (v) Identify the distribution frequency on the securities. (vi) Summarize the flow...

10 CFR 205.322 - Contents of application.

Code of Federal Regulations, 2013 CFR

2013-01-01

... diagrams which provide clarification of any of the above items should be included. (2) A general area map... conductor ratings; (ii) System power flow plots for the applicant's service area for heavy summer and light... is scheduled to be placed in service and for the fifth year thereafter. The power flow plots...

30 CFR 250.154 - What identification signs must I display?

Code of Federal Regulations, 2013 CFR

2013-07-01

... number of the facility location as depicted on OCS Official Protraction Diagrams or leasing maps; (iii...; and (3) For subsea wells that flow individually into separate pipelines, affix the required sign on... receiving platform. For multiple subsea wells that flow into a common pipeline or pipelines, no sign is...

17 CFR 229.1103 - (Item 1103) Transaction summary and risk factors.

Code of Federal Regulations, 2014 CFR

2014-04-01

... if doing so will aid understanding. Consider using diagrams to illustrate the relationships among the parties, the structure of the securities offered (including, for example, the flow of funds or any... securities may be issued. (v) Identify the distribution frequency on the securities. (vi) Summarize the flow...

30 CFR 250.154 - What identification signs must I display?

Code of Federal Regulations, 2012 CFR

2012-07-01

... number of the facility location as depicted on OCS Official Protraction Diagrams or leasing maps; (iii...; and (3) For subsea wells that flow individually into separate pipelines, affix the required sign on... receiving platform. For multiple subsea wells that flow into a common pipeline or pipelines, no sign is...

30 CFR 250.154 - What identification signs must I display?

Code of Federal Regulations, 2011 CFR

2011-07-01

... number of the facility location as depicted on OCS Official Protraction Diagrams or leasing maps; (iii...; and (3) For subsea wells that flow individually into separate pipelines, affix the required sign on... receiving platform. For multiple subsea wells that flow into a common pipeline or pipelines, no sign is...

School Improvement Processes in Career Education.

ERIC Educational Resources Information Center

Smey, Barbara A.

This manual is designed to review those topics which should be considered when initiating a school improvement effort in career education. These materials, representing a one-day workshop, consist of seven activities. Topics covered in the activities are an overview of the workshop, work flow and a work-flow diagram, needs assessment, career…

Sequential Learning and Recognition of Comprehensive Behavioral Patterns Based on Flow of People

NASA Astrophysics Data System (ADS)

Gibo, Tatsuya; Aoki, Shigeki; Miyamoto, Takao; Iwata, Motoi; Shiozaki, Akira

Recently, surveillance cameras have been set up everywhere, for example, in streets and public places, in order to detect irregular situations. In the existing surveillance systems, as only a handful of surveillance agents watch a large number of images acquired from surveillance cameras, there is a possibility that they may miss important scenes such as accidents or abnormal incidents. Therefore, we propose a method for sequential learning and the recognition of comprehensive behavioral patterns in crowded places. First, we comprehensively extract a flow of people from input images by using optical flow. Second, we extract behavioral patterns on the basis of change-point detection of the flow of people. Finally, in order to recognize an observed behavioral pattern, we draw a comparison between the behavioral pattern and previous behavioral patterns in the database. We verify the effectiveness of our approach by placing a surveillance camera on a campus.

T -odd correlations in polarized top quark decays in the sequential decay t (↑)→Xb+W+(→ℓ++νℓ) and in the quasi-three-body decay t (↑)→ Xb+ℓ++νℓ

NASA Astrophysics Data System (ADS)

Fischer, M.; Groote, S.; Körner, J. G.

2018-05-01

We identify the T -odd structure functions that appear in the description of polarized top quark decays in the sequential decay t (↑)→Xb+W+(→ℓ++νℓ) (two structure functions) and the quasi-three-body decay t (↑)→X b+ℓ++νℓ (one structure function). A convenient measure of the magnitude of the T -odd structure functions is the contribution of the imaginary part Im gR of the right-chiral tensor coupling gR to the T -odd structure functions which we work out. Contrary to the case of QCD, the NLO electroweak corrections to polarized top quark decays admit absorptive one-loop vertex contributions. We analytically calculate the imaginary parts of the relevant four electroweak one-loop triangle vertex diagrams and determine their contributions to the T -odd helicity structure functions that appear in the description of polarized top quark decays.

Dynamics of C2H 2 3 +→H++H++C 2 + investigated by 50-keV/u Ne8 + impact

NASA Astrophysics Data System (ADS)

Xu, S.; Zhu, X. L.; Feng, W. T.; Guo, D. L.; Zhao, Q.; Yan, S.; Zhang, P.; Zhao, D. M.; Gao, Y.; Zhang, S. F.; Yang, J.; Ma, X.

2018-06-01

Breakup dynamics of C2H 2 3 + → H++H++C 2 + induced by 50-keV/u Ne8 + ion impact is investigated employing a reaction microscope. All three ionic fragments in the final state are detected in coincidence, and their momentum vectors as well as the kinetic energies are determined. The kinetic-energy correlation spectrum of the two protons displays very rich structures. Utilizing the Newton diagrams and the Dalitz plots, different dissociation mechanisms corresponding to these structures are identified. It was found that, besides the concerted and sequential breakup, fragmentation mechanisms associated with different vibration modes including molecular bending and asymmetric stretching also make significant contributions. We analyzed the correlation between different fragmentation mechanisms and the kinetic-energy release (KER) and found that the sequential process occurs with higher KER while, in contrast, the concerted process mainly contributes to the lower KER. This behavior is entirely opposite to the breakup of the CO2 molecule.

Bifurcation analysis of a heterogeneous traffic flow model

NASA Astrophysics Data System (ADS)

Wang, Yu-Qing; Yan, Bo-Wen; Zhou, Chao-Fan; Li, Wei-Kang; Jia, Bin

2018-03-01

In this work, a heterogeneous traffic flow model coupled with the periodic boundary condition is proposed. Based on the previous models, a heterogeneous system composed of more than one kind of vehicles is considered. By bifurcation analysis, bifurcation patterns of the heterogeneous system are discussed in three situations in detail and illustrated by diagrams of bifurcation patterns. Besides, the stability analysis of the heterogeneous system is performed to test its anti-interference ability. The relationship between the number of vehicles and the stability is obtained. Furthermore, the attractor analysis is applied to investigate the nature of the heterogeneous system near its steady-state neighborhood. Phase diagrams of the process of the heterogeneous system from initial state to equilibrium state are intuitively presented.

Using the Circular Flow of Income Model to Teach Economics in the Middle School Classroom

ERIC Educational Resources Information Center

Marks, Melanie; Kotula, Gemma

2009-01-01

The circular flow of income diagram is a traditional starting point for economics taught at the high school and college level. Although it is an incredibly useful tool for illustrating how money flows through the economy, the model can be abstract and relies on a sophisticated vocabulary that makes it impractical for use with younger students.…

Study on a novel laser target detection system based on software radio technique

NASA Astrophysics Data System (ADS)

Song, Song; Deng, Jia-hao; Wang, Xue-tian; Gao, Zhen; Sun, Ji; Sun, Zhi-hui

2008-12-01

This paper presents that software radio technique is applied to laser target detection system with the pseudo-random code modulation. Based on the theory of software radio, the basic framework of the system, hardware platform, and the implementation of the software system are detailed. Also, the block diagram of the system, DSP circuit, block diagram of the pseudo-random code generator, and soft flow diagram of signal processing are designed. Experimental results have shown that the application of software radio technique provides a novel method to realize the modularization, miniaturization and intelligence of the laser target detection system, and the upgrade and improvement of the system will become simpler, more convenient, and cheaper.

Statistical process control: a practical application for hospitals.

PubMed

VanderVeen, L M

1992-01-01

A six-step plan based on using statistics was designed to improve quality in the central processing and distribution department of a 223-bed hospital in Oakland, CA. This article describes how the plan was implemented sequentially, starting with the crucial first step of obtaining administrative support. The QI project succeeded in overcoming beginners' fear of statistics and in training both managers and staff to use inspection checklists, Pareto charts, cause-and-effect diagrams, and control charts. The best outcome of the program was the increased commitment to quality improvement by the members of the department.

Statistical analysis of dispersion relations in turbulent solar wind fluctuations using Cluster data

NASA Astrophysics Data System (ADS)

Perschke, C.; Narita, Y.

2012-12-01

Multi-spacecraft measurements enable us to resolve three-dimensional spatial structures without assuming Taylor's frozen-in-flow hypothesis. This is very useful to study frequency-wave vector diagram in solar wind turbulence through direct determination of three-dimensional wave vectors. The existence and evolution of dispersion relation and its role in fully-developed plasma turbulence have been drawing attention of physicists, in particular, if solar wind turbulence represents kinetic Alfvén or whistler mode as the carrier of spectral energy among different scales through wave-wave interactions. We investigate solar wind intervals of Cluster data for various flow velocities with a high-resolution wave vector analysis method, Multi-point Signal Resonator technique, at the tetrahedral separation about 100 km. Magnetic field data and ion data are used to determine the frequency- wave vector diagrams in the co-moving frame of the solar wind. We find primarily perpendicular wave vectors in solar wind turbulence which justify the earlier discussions about kinetic Alfvén or whistler wave. The frequency- wave vector diagrams confirm (a) wave vector anisotropy and (b) scattering in frequencies.

Kinematic capability in the SVDS

NASA Technical Reports Server (NTRS)

Flanders, H. A.

1977-01-01

The details of the Remote Manipulator System kinematic model implemented into the Space Vehicle Dynamics Simulation are given. Detailed engineering flow diagrams and definitions of terms are included.

Maths Resource.

ERIC Educational Resources Information Center

Tapson, Frank

1985-01-01

Flow diagrams developing cube roots and formulas for the square, sphere, cube, circle and sector, oblong, and cylinder are presented. Some comments on their use, along with calculators, are included. (MNS)

Sequential lineups: shift in criterion or decision strategy?

PubMed

Gronlund, Scott D

2004-04-01

R. C. L. Lindsay and G. L. Wells (1985) argued that a sequential lineup enhanced discriminability because it elicited use of an absolute decision strategy. E. B. Ebbesen and H. D. Flowe (2002) argued that a sequential lineup led witnesses to adopt a more conservative response criterion, thereby affecting bias, not discriminability. Height was encoded as absolute (e.g., 6 ft [1.83 m] tall) or relative (e.g., taller than). If a sequential lineup elicited an absolute decision strategy, the principle of transfer-appropriate processing predicted that performance should be best when height was encoded absolutely. Conversely, if a simultaneous lineup elicited a relative decision strategy, performance should be best when height was encoded relatively. The predicted interaction was observed, providing direct evidence for the decision strategies explanation of what happens when witnesses view a sequential lineup.

The flow patterning capability of localized natural convection.

PubMed

Huang, Ling-Ting; Chao, Ling

2016-09-14

Controlling flow patterns to align materials can have various applications in optics, electronics, and biosciences. In this study, we developed a natural-convection-based method to create desirable spatial flow patterns by controlling the locations of heat sources. Fluid motion in natural convection is induced by the spatial fluid density gradient that is caused by the established spatial temperature gradient. To analyze the patterning resolution capability of this method, we used a mathematical model combined with nondimensionalization to correlate the flow patterning resolution with experimental operating conditions. The nondimensionalized model suggests that the flow pattern and resolution is only influenced by two dimensionless parameters, and , where Gr is the Grashof number, representing the ratio of buoyancy to the viscous force acting on a fluid, and Pr is the Prandtl number, representing the ratio of momentum diffusivity to thermal diffusivity. We used the model to examine all of the flow behaviors in a wide range of the two dimensionless parameter group and proposed a flow pattern state diagram which suggests a suitable range of operating conditions for flow patterning. In addition, we developed a heating wire with an angular configuration, which enabled us to efficiently examine the pattern resolution capability numerically and experimentally. Consistent resolutions were obtained between the experimental results and model predictions, suggesting that the state diagram and the identified operating range can be used for further application.

Reducing Electroosmotic Flow Enables DNA Separations in Ultrathin Channels.

DTIC Science & Technology

1998-08-01

Chemical structure of DNA bases 2 Figure 1-2: Schematic diagram of DNA base pairing 5 Figure 1-3: Schematic diagram of the capillary and the...hydrogen atoms near one of the Figure 1-1: A. Chemical structure of the DNA backbone. B. Chemical structure of DNA bases . The DNA backbone consists...of pentose sugar (deoxyribose) held together by phosphodiester bonds. The DNA bases that are derivatives of purine are adenine (A) and guanine (G

Strengthening by Substitutional Solutes and the Temperature Dependence of the Flow Stress in Ni3Al

DTIC Science & Technology

1989-05-26

stoichiometric composition in polycrystalline Ni3AI and Ni3Ga. 29 Fig. 3.1 The Ni-Al binary-alloy phase diagram in vacinity of Ni3A1 phase, as verified in...I <I- iai / I I- I I I I000 - - II 21 25 29 33 37 ATOMIC % Al Fig. 3.1 The Ni-Al binary-alloy phase diagram in vacinity of Ni3Al phase, as verified

Notes on Experiments.

ERIC Educational Resources Information Center

Physics Education, 1988

1988-01-01

Describes three experiments: (1) "Liquid Flow from Orifices"; (2) "Microcomputer-Controlled Investigation of Battery Discharge and Recovery"; and (3) "Measurement of the Speed of Sound." Drawings and diagrams accompany each. (RT)

30 CFR 250.154 - What identification signs must I display?

Code of Federal Regulations, 2010 CFR

2010-07-01

... depicted on OCS Official Protraction Diagrams or leasing maps; (iii) In the Pacific OCS Region, list the... lease number individually on the well flowline at the wellhead; and (3) For subsea wells that flow... flow into a common pipeline or pipelines, no sign is required. Right-of-use and Easement ...

How to Read an LLNL Energy Flow Chart (Sankey Diagram)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Simon, A. J.

Each year, the Lawrence Livermore National Laboratory releases energy flow charts that illustrate the nation's consumption and use of energy. A.J. Simon, group leader for LLNL’s energy program, breaks the 2015 chart down in this video, describing how to read the chart and what year-to-year trends he sees.

16. Photocopy of drawing # F1103 in files of Utilities ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

16. Photocopy of drawing # F-1103 in files of Utilities Engineering Department in Cleveland showing water flow diagram in the Division Avenue Plant. Drawing dated March 11, 1921. Flow is still in existence. - Division Avenue Pumping Station & Filtration Plant, West 45th Street and Division Avenue, Cleveland, Cuyahoga County, OH

A theory of rotating stall of multistage axial compressors

NASA Technical Reports Server (NTRS)

Moore, F. K.

1983-01-01

A theoretical analysis was made of rotating stall in axial compressors of many stages, finding conditions for a permanent, straight-through traveling disturbance, with the steady compressor characteristic assumed known, and with simple lag processes ascribed to the flows in the inlet, blade passages, and exit regions. For weak disturbances, predicted stall propagation speeds agree well with experimental results. For a locally-parabolic compressor characteristic, an exact nonlinear solution is found and discussed. For deep stall, the stall-zone boundary is most abrupt at the trailing edge, as expected. When a complete characteristic having unstalling and reverse-flow features is adopted, limit cycles governed by a Lienard's equation are found. Analysis of these cycles yields predictions of recovery from rotating stall; a relaxation oscillation is found at some limiting flow coefficient, above which no solution exists. Recovery is apparently independent of lag processes in the blade passages, but instead depends on the lags originating in the inlet and exit flows, and also on the shape of the given characteristic diagram. Small external lags and tall diagrams favor early recovery. Implications for future research are discussed.

Microfluidic Device for Sequential Injection and Flushing of Solutions and its Application to Immunosensing

NASA Astrophysics Data System (ADS)

Nashida, Norihiro; Suzuki, Hiroaki

A microfluidic system with injecting and flushing functions was developed. In the system, hydrophilic flow channels have a dry-film photoresist layer which facilitates the introduction of solutions from four injection ports. The injection and flushing of solutions are controlled by valves operated by electrowetting. The valves consist of gold working electrodes in the flow channels or a through-hole in the glass substrate. Solutions can be sequentially introduced through the injection ports into a reaction chamber and flushed through a valve in the through-hole. Necessary immunoassay steps can be conducted on the chip, and a target antibody can be detected electrochemically.

Self-assembly of colloidal particles from evaporating droplets: role of DLVO interactions and proposition of a phase diagram.

PubMed

Bhardwaj, Rajneesh; Fang, Xiaohua; Somasundaran, Ponisseril; Attinger, Daniel

2010-06-01

The shape of deposits obtained from drying drops containing colloidal particles matters for technologies such as inkjet printing, microelectronics, and bioassay manufacturing. In this work, the formation of deposits during the drying of nanoliter drops containing colloidal particles is investigated experimentally with microscopy and profilometry, and theoretically with an in-house finite-element code. The system studied involves aqueous drops containing titania nanoparticles evaporating on a glass substrate. Deposit shapes from spotted drops at different pH values are measured using a laser profilometer. Our results show that the pH of the solution influences the dried deposit pattern, which can be ring-like or more uniform. The transition between these patterns is explained by considering how DLVO interactions such as the electrostatic and van der Waals forces modify the particle deposition process. Also, a phase diagram is proposed to describe how the shape of a colloidal deposit results from the competition among three flow patterns: a radial flow driven by evaporation at the wetting line, a Marangoni recirculating flow driven by surface tension gradients, and the transport of particles toward the substrate driven by DLVO interactions. This phase diagram explains three types of deposits commonly observed experimentally, such as a peripheral ring, a small central bump, or a uniform layer. Simulations and experiments are found in very good agreement.

An Electroacoustic Hearing Protector Simulator That Accurately Predicts Pressure Levels in the Ear Based on Standard Performance Metrics

DTIC Science & Technology

2013-08-01

earplug and earmuff showing HPD simulator elements for energy flow paths...unprotected or protected ear traditionally start with analysis of energy flow through schematic diagrams based on electroacoustic (EA) analogies between...Schröter, 1983; Schröter and Pösselt, 1986; Shaw and Thiessen, 1958, 1962; Zwislocki, 1957). The analysis method tracks energy flow through fluid and

Recent Electrochemical and Optical Sensors in Flow-Based Analysis

PubMed Central

Chailapakul, Orawon; Ngamukot, Passapol; Yoosamran, Alongkorn; Siangproh, Weena; Wangfuengkanagul, Nattakarn

2006-01-01

Some recent analytical sensors based on electrochemical and optical detection coupled with different flow techniques have been chosen in this overview. A brief description of fundamental concepts and applications of each flow technique, such as flow injection analysis (FIA), sequential injection analysis (SIA), all injection analysis (AIA), batch injection analysis (BIA), multicommutated FIA (MCFIA), multisyringe FIA (MSFIA), and multipumped FIA (MPFIA) were reviewed.

[Prospective comparison of the flow chart for laboratory investigations for anaemia from the Dutch College of General Practitioners' guideline 'Anaemia' with a self-developed, substantive and logistical alternative flow chart].

PubMed

Oosterhuis, W P; van der Horst, M; van Dongen, K; Ulenkate, H J L M; Volmer, M; Wulkan, R W

2007-10-20

To compare the flow diagram for the diagnosis of anaemia from the guideline 'Anaemia' from the Dutch College of General Practitioners (NHG) with a substantive and logistical alternative protocol. Prospective. For evaluation of anaemia, 124 patients from primary care reported to the laboratories of the St. Elisabeth Hospital in Tilburg (n = 94) and the Scheper Hospital in Emmen (n = 30), the Netherlands. Two flow charts were used: the NHG's flow chart and a self-developed chart in which not mean corpuscular volume, but ferritin concentration occupies the central position. All the laboratory tests mentioned in both flow charts were carried out in every patient with, for practical reasons, the exception of Hgb electrophoresis and bone marrow investigations. General practitioners were approached and patient dossiers were consulted to obtain further clinical data. According to the NHG protocol, on the grounds of the laboratory investigations, 64 (52%) of patients could not be put in a specific category. The majority were patients with normocytary anaemia who did not fulfil the criteria for iron deficiency anaemia or the anaemia of chronic disease. According to the alternative chart, in 36 (29%) patients no diagnosis was made. These were patients in whom no abnormal laboratory findings were observed, other than low haemoglobin values. The majority of the patients had normocytary anaemia, in some cases this was interpreted as the anaemia of chronic disease, but more often the anaemia could not be assigned to a particular category. A large number ofpatients had a raised creatinine value. This value did not appear in the NHG protocol. In 15% of patients, more than one cause for anaemia was found. The NHG protocol did not enable these multiple diagnoses to be made. Accordingly, the NHG protocol was difficult to implement in the laboratory. Using the NHG flow diagram a large percentage of patients could not be assigned to a particular category. Using the alternative flow diagram, which procedure is easier to carry out in the laboratory, it was possible to make multiple diagnoses.

In situ epoxide generation by dimethyldioxirane oxidation and the use of epichlorohydrin in the flow synthesis of a library of β-amino alcohols.

PubMed

Cossar, Peter J; Baker, Jennifer R; Cain, Nicholas; McCluskey, Adam

2018-04-01

The flow coupling of epichlorohydrin with substituted phenols, while efficient, limits the nature of the epoxide available for the development of focused libraries of β-amino alcohols. This limitation was encountered in the production of analogues of 1-(4-nitrophenoxy)-3-((2-((4-(trifluoromethyl)pyrimidin-2-yl)amino)ethyl)amino)propan-2-ol 1 , a potential antibiotic lead. The in situ (flow) generation of dimethyldoxirane (DMDO) and subsequent flow olefin epoxidation abrogates this limitation and afforded facile access to structurally diverse β-amino alcohols. Analogues of 1 were readily accessed either via (i) a flow/microwave hybrid approach, or (ii) a sequential flow approach. Key steps were the in situ generation of DMDO, with olefin epoxidation in typically good yields and a flow-mediated ring opening aminolysis to form an expanded library of β-amino alcohols 1 and 10a - 18g , resulting in modest ( 11a , 21%) to excellent ( 12g , 80%) yields. Alternatively flow coupling of epichlorohydrin with phenols 4a - 4m (22%-89%) and a Bi(OTf) 3 catalysed microwave ring opening with amines afforded a select range of β-amino alcohols, but with lower levels of aminolysis regiocontrol than the sequential flow approach.

In situ epoxide generation by dimethyldioxirane oxidation and the use of epichlorohydrin in the flow synthesis of a library of β-amino alcohols

PubMed Central

Cossar, Peter J.; Baker, Jennifer R.; Cain, Nicholas

2018-01-01

The flow coupling of epichlorohydrin with substituted phenols, while efficient, limits the nature of the epoxide available for the development of focused libraries of β-amino alcohols. This limitation was encountered in the production of analogues of 1-(4-nitrophenoxy)-3-((2-((4-(trifluoromethyl)pyrimidin-2-yl)amino)ethyl)amino)propan-2-ol 1, a potential antibiotic lead. The in situ (flow) generation of dimethyldoxirane (DMDO) and subsequent flow olefin epoxidation abrogates this limitation and afforded facile access to structurally diverse β-amino alcohols. Analogues of 1 were readily accessed either via (i) a flow/microwave hybrid approach, or (ii) a sequential flow approach. Key steps were the in situ generation of DMDO, with olefin epoxidation in typically good yields and a flow-mediated ring opening aminolysis to form an expanded library of β-amino alcohols 1 and 10a–18g, resulting in modest (11a, 21%) to excellent (12g, 80%) yields. Alternatively flow coupling of epichlorohydrin with phenols 4a–4m (22%–89%) and a Bi(OTf)3 catalysed microwave ring opening with amines afforded a select range of β-amino alcohols, but with lower levels of aminolysis regiocontrol than the sequential flow approach. PMID:29765627

Analysis of internal flow characteristics of a smooth-disk water-brake dynamometer

NASA Technical Reports Server (NTRS)

Evans, D. G.

1973-01-01

The principal of absorbing power with an enclosed partially submerged rotating disk through the turbulent viscous shearing of water is discussed. Reference information is used to develop a flow model of the water brake. A method is then presented that uses vector diagrams to relate the effects of rotational flow, through flow, and secondary flow to power absorption. The method is used to describe the operating characteristics of an example 111-cm (43.7-in.) diameter water brake. Correlating performance parameters are developed in a dimensional analysis.

White Toenails

MedlinePlus

... name. Search Where do you hurt? Interactive Foot Diagram Yellow Toenails The most common cause of yellow ... Arterial Disease (PAD) is the restriction of blood flow in the arteries of the leg. When... Ingrown ...

Thick Toenails

MedlinePlus

... name. Search Where do you hurt? Interactive Foot Diagram Yellow Toenails The most common cause of yellow ... Arterial Disease (PAD) is the restriction of blood flow in the arteries of the leg. When... Ingrown ...

A system for programming experiments and for recording and analyzing data automatically1

PubMed Central

Herrick, Robert M.; Denelsbeck, John S.

1963-01-01

A system designed for use in complex operant conditioning experiments is described. Some of its key features are: (a) plugboards that permit the experimenter to change either from one program to another or from one analysis to another in less than a minute, (b) time-sharing of permanently-wired, electronic logic components, (c) recordings suitable for automatic analyses. Included are flow diagrams of the system and sample logic diagrams for programming experiments and for analyzing data. ImagesFig. 4. PMID:14055967

Nuclear Aircraft Feasibility Study. Volume 1

DTIC Science & Technology

1975-03-01

Cycle 6-36 6.2.2 Helium Mass Flow 6-42 6.2.3 Fan Pressure Ratio 6-42 6.2.4 Regenerative Cycle Application 6-43 6.2.5 Brayton Cycle...6-8 Engine Systems Summary 6-9 T-S Diagram of Ideal Brayton Cycle 6-13 T-S Diagram of Brayton Cycle for Turbofan Engine 6-15 Comparison of... Brayton Closed Cycle Thermodynamic Analysis 6-50 6.2.8-1 Indirect Cycle Gas Circulation System 6-53 6.2.8-2 Gas Turbine Generator — Pump Cycle

T-Check in Technologies for Interoperability: Business Process Management in a Web Services Context

DTIC Science & Technology

2008-09-01

UML Sequence Diagram) 6  Figure 3:   BPMN Diagram of the Order Processing Business Process 9  Figure 4:   T-Check Process for Technology Evaluation 10...Figure 5:  Notional System Architecture 12  Figure 6:  Flow Chart of the Order Processing Business Process 14  Figure 7:  Order Processing Activities...features. Figure 3 (created with Intalio BPMS Designer [Intalio 2008]) shows a BPMN view of the Order Processing business process that is used in the

Computer modeling of human decision making

NASA Technical Reports Server (NTRS)

Gevarter, William B.

1991-01-01

Models of human decision making are reviewed. Models which treat just the cognitive aspects of human behavior are included as well as models which include motivation. Both models which have associated computer programs, and those that do not, are considered. Since flow diagrams, that assist in constructing computer simulation of such models, were not generally available, such diagrams were constructed and are presented. The result provides a rich source of information, which can aid in construction of more realistic future simulations of human decision making.

Topological transitions for lattice bosons in a magnetic field

PubMed Central

Huber, Sebastian D.; Lindner, Netanel H.

2011-01-01

The Hall response provides an important characterization of strongly correlated phases of matter. We study the Hall conductivity of interacting bosons on a lattice subjected to a magnetic field. We show that for any density or interaction strength, the Hall conductivity is characterized by an integer. We find that the phase diagram is intersected by topological transitions between different values of this integer. These transitions lead to surprising effects, including sign reversal of the Hall conductivity and extensive regions in the phase diagram where it acquires a negative sign, which implies that flux flow is reversed in these regions—vortices there flow upstream. Our findings have immediate applications to a wide range of phenomena in condensed matter physics, which are effectively described in terms of lattice bosons. PMID:22109548

IGDS/TRAP Interface Program (ITIP). Software User Manual (SUM). [network flow diagrams for coal gasification studies

NASA Technical Reports Server (NTRS)

Jefferys, S.; Johnson, W.; Lewis, R.; Rich, R.

1981-01-01

This specification establishes the requirements, concepts, and preliminary design for a set of software known as the IGDS/TRAP Interface Program (ITIP). This software provides the capability to develop at an Interactive Graphics Design System (IGDS) design station process flow diagrams for use by the NASA Coal Gasification Task Team. In addition, ITIP will use the Data Management and Retrieval System (DMRS) to maintain a data base from which a properly formatted input file to the Time-Line and Resources Analysis Program (TRAP) can be extracted. This set of software will reside on the PDP-11/70 and will become the primary interface between the Coal Gasification Task Team and IGDS, DMRS, and TRAP. The user manual for the computer program is presented.

Poisson's ratio of fiber-reinforced composites

NASA Astrophysics Data System (ADS)

Christiansson, Henrik; Helsing, Johan

1996-05-01

Poisson's ratio flow diagrams, that is, the Poisson's ratio versus the fiber fraction, are obtained numerically for hexagonal arrays of elastic circular fibers in an elastic matrix. High numerical accuracy is achieved through the use of an interface integral equation method. Questions concerning fixed point theorems and the validity of existing asymptotic relations are investigated and partially resolved. Our findings for the transverse effective Poisson's ratio, together with earlier results for random systems by other authors, make it possible to formulate a general statement for Poisson's ratio flow diagrams: For composites with circular fibers and where the phase Poisson's ratios are equal to 1/3, the system with the lowest stiffness ratio has the highest Poisson's ratio. For other choices of the elastic moduli for the phases, no simple statement can be made.

Dynamic phase diagram of a nonionic surfactant lamellar phase.

PubMed

Gentile, Luigi; Behrens, Manja A; Balog, Sandor; Mortensen, Kell; Ranieri, Giuseppe A; Olsson, Ulf

2014-04-03

The dynamic phase diagram of triethylene glycol dodecyl ether (C12E3) in D2O was determined for 40, 50, and 60 wt % of surfactant. The shear flow effect on the nonionic lamellar phase was investigated as a function of temperature and concentration. The transition from planar lamellae (Lα)-to-multilamellar vesicles (MLVs) was characterized by means of rheology, rheo-small-angle neutron and light scattering. New insight into the nature of the transition region between Lα and the MLVs state is provided. A disorder-order transition was also observed by SANS. This is attributed to a transition from disordered MLVs to a close-packed array of MLV's with slightly higher order than before. Moreover flow instability was observed in the shear-thickening regime at 40 °C.

Stability diagram for dense suspensions of model colloidal Al2O3 particles in shear flow.

PubMed

Hecht, Martin; Harting, Jens; Herrmann, Hans J

2007-05-01

In Al2O3 suspensions, depending on the experimental conditions, very different microstructures can be found, comprising fluidlike suspensions, a repulsive structure, and a clustered microstructure. For technical processing in ceramics, the knowledge of the microstructure is of importance, since it essentially determines the stability of a workpiece to be produced. To enlighten this topic, we investigate these suspensions under shear by means of simulations. We observe cluster formation on two different length scales: the distance of nearest neighbors and on the length scale of the system size. We find that the clustering behavior does not depend on the length scale of observation. If interparticle interactions are not attractive the particles form layers in the shear flow. The results are summarized in a stability diagram.

Analysis of pedestrian dynamics in counter flow via an extended lattice gas model.

PubMed

Kuang, Hua; Li, Xingli; Song, Tao; Dai, Shiqiang

2008-12-01

The modeling of human behavior is an important approach to reproduce realistic phenomena for pedestrian flow. In this paper, an extended lattice gas model is proposed to simulate pedestrian counter flow under the open boundary conditions by considering the human subconscious behavior and different maximum velocities. The simulation results show that the presented model can capture some essential features of pedestrian counter flows, such as lane formation, segregation effect, and phase separation at higher densities. In particular, an interesting feature that the faster walkers overtake the slower ones and then form a narrow-sparse walkway near the central partition line is discovered. The phase diagram comparison and analysis show that the subconscious behavior plays a key role in reducing the occurrence of jam cluster. The effects of the symmetrical and asymmetrical injection rate, different partition lines, and different combinations of maximum velocities on pedestrian flow are investigated. An important conclusion is that it is needless to separate faster and slower pedestrians in the same direction by a partition line. Furthermore, the increase of the number of faster walkers does not always benefit the counter flow in all situations. It depends on the magnitude and asymmetry of injection rate. And at larger maximum velocity, the obtained critical transition point corresponding to the maximum flow rate of the fundamental diagram is in good agreement with the empirical results.

Development of high-accuracy convection schemes for sequential solvers

NASA Technical Reports Server (NTRS)

Thakur, Siddharth; Shyy, Wei

1993-01-01

An exploration is conducted of the applicability of such high resolution schemes as TVD to the resolving of sharp flow gradients using a sequential solution approach borrowed from pressure-based algorithms. It is shown that by extending these high-resolution shock-capturing schemes to a sequential solver that treats the equations as a collection of scalar conservation equations, the speed of signal propagation in the solution has to be coordinated by assigning the local convection speed as the characteristic speed for the entire system. A higher amount of dissipation is therefore needed to eliminate oscillations near discontinuities.

Tense and aspect in word problems about motion: diagram, gesture, and the felt experience of time

NASA Astrophysics Data System (ADS)

de Freitas, Elizabeth; Zolkower, Betina

2015-09-01

Word problems about motion contain various conjugated verb forms. As students and teachers grapple with such word problems, they jointly operationalize diagrams, gestures, and language. Drawing on findings from a 3-year research project examining the social semiotics of classroom interaction, we show how teachers and students use gesture and diagram to make sense of complex verb forms in such word problems. We focus on the grammatical category of "aspect" for how it broadens the concept of verb tense. Aspect conveys duration and completion or frequency of an event. The aspect of a verb defines its temporal flow (or lack thereof) and the location of a vantage point for making sense of this durational process.

Computational fluid dynamics study of the end-side and sequential coronary artery bypass anastomoses in a native coronary occlusion model.

PubMed

Matsuura, Kaoru; Jin, Wei Wei; Liu, Hao; Matsumiya, Goro

2018-04-01

The objective of this study was to evaluate the haemodynamic patterns in each anastomosis fashion using a computational fluid dynamic study in a native coronary occlusion model. Fluid dynamic computations were carried out with ANSYS CFX (ANSYS Inc., Canonsburg, PA, USA) software. The incision lengths for parallel and diamond anastomoses were fixed at 2 mm. Native vessels were set to be totally occluded. The diameter of both the native and graft vessels was set to be 2 mm. The inlet boundary condition was set by a sample of the transient time flow measurement which was measured intraoperatively. The diamond anastomosis was observed to reduce flow to the native outlet and increase flow to the bypass outlet; the opposite was observed in the parallel anastomosis. Total energy efficiency was higher in the diamond anastomosis than the parallel anastomosis. Wall shear stress was higher in the diamond anastomosis than in the parallel anastomosis; it was the highest at the top of the outlet. A high oscillatory shear index was observed at the bypass inlet in the parallel anastomosis and at the native inlet in the diamond anastomosis. The diamond sequential anastomosis would be an effective option for multiple sequential bypasses because of the better flow to the bypass outlet than with the parallel anastomosis. However, flow competition should be kept in mind while using the diamond anastomosis for moderately stenotic vessels because of worsened flow to the native outlet. Care should be taken to ensure that the fluid dynamics patterns are optimal and prevent future native and bypass vessel disease progression.

Studies of vehicle overtaking dynamics and its influence on traffic flow at a bidirectional road

NASA Astrophysics Data System (ADS)

Echab, H.; Marzoug, R.; Lakouari, N.; Ez-Zahraouy, H.

For the purposes of optimizing traffic flow composed of different types of vehicles, it is important to understand the interactions between them. This paper proposes a cellular automata model to investigate a bidirectional two-lane traffic flow under the periodic boundary condition. The vehicle flux and the phase diagrams of the system in the (ρ1,ρ2) space are constructed by applying two different overtaking models (symmetric, asymmetric). The inter-lane correlation and the overtaking frequency are also studied. The simulation results show that the variation of the density of one lane has an apparent influence on the traffic of the adjacent lane. Furthermore, it is found that the phase diagram on both models is classified into several regions. Thus, for the symmetric model, as the overtaking probability increases, the traffic on the system becomes better. Likewise, the results also indicate that the asymmetric model can effectively enhance the traffic capacity and alleviate the congested state.

Unifying Suspension and Granular flows near Jamming

NASA Astrophysics Data System (ADS)

DeGiuli, Eric; Wyart, Matthieu

2017-06-01

Rheological properties of dense flows of hard particles are singular as one approaches the jamming threshold where flow ceases, both for granular flows dominated by inertia, and for over-damped suspensions. Concomitantly, the lengthscale characterizing velocity correlations appears to diverge at jamming. Here we review a theoretical framework that gives a scaling description of stationary flows of frictionless particles. Our analysis applies both to suspensions and inertial flows of hard particles. We report numerical results in support of the theory, and show the phase diagram that results when friction is added, delineating the regime of validity of the frictionless theory.

The Intelligent Management System: An Overview.

DTIC Science & Technology

1982-12-07

comprises of hundreds of subprocesses concerned with bulb grasping, positioning, heating, cooling, etc. Each is sequentially related with others in time...activity. Activity schemata can be constructed into a network to define both parallel and sequential precedence, and hierarchical to describe...The flow of work is controlled by the "operation- lineup " associated with the product being manufactured. The operation- lineup specifies the sequence of

How to Read an LLNL Energy Flow Chart (Sankey Diagram)

ScienceCinema

Simon, A. J.

2018-01-16

Each year, the Lawrence Livermore National Laboratory releases energy flow charts that illustrate the nation's consumption and use of energy. A.J. Simon, group leader for LLNL’s energy program, breaks the 2015 chart down in this video, describing how to read the chart and what year-to-year trends he sees.

Concept for a Satellite-Based Advanced Air Traffic Management System : Volume 8. Operational Logic Flow Diagrams for a Generic Advanced Air Traffic Management system

DOT National Transportation Integrated Search

1974-02-01

The volume presents a description of the services a generic Advanced Air Traffic Management System (AATMS) should provide to the useres of the system to facilitate the safe, efficient flow of traffic. It provides a definition of the functions which t...

Predicting the Performance of an Axial-Flow Compressor

NASA Technical Reports Server (NTRS)

Steinke, R. J.

1986-01-01

Stage-stacking computer code (STGSTK) developed for predicting off-design performance of multi-stage axial-flow compressors. Code uses meanline stagestacking method. Stage and cumulative compressor performance calculated from representative meanline velocity diagrams located at rotor inlet and outlet meanline radii. Numerous options available within code. Code developed so user modify correlations to suit their needs.

33 CFR 154.2022 - Certification, recertification, or operational review-certifying entity responsibilities, generally.

Code of Federal Regulations, 2014 CFR

2014-07-01

... alarm and shutdown shown on the piping and instrumentation diagrams (P&IDs) and reviewed in the hazard... cleaning facility; and that (5) The automatic liquid block valve successfully stops flow of liquid to the... automatically stop the cargo flow to each transfer hose simultaneously, in the event an upset condition occurs...

Isothermal Time-Temperature-Precipitation Diagram for an Aluminum Alloy 6005A by In Situ DSC Experiments

PubMed Central

Milkereit, Benjamin; Giersberg, Lydia; Kessler, Olaf; Schick, Christoph

2014-01-01

Time-temperature-precipitation (TTP) diagrams deliver important material data, such as temperature and time ranges critical for precipitation during the quenching step of the age hardening procedure. Although the quenching step is continuous, isothermal TTP diagrams are often applied. Together with a so-called Quench Factor Analysis, they can be used to describe very different cooling paths. Typically, these diagrams are constructed based on mechanical properties or microstructures after an interrupted quenching, i.e., ex situ analyses. In recent years, an in situ calorimetric method to record continuous cooling precipitation diagrams of aluminum alloys has been developed to the application level by our group. This method has now been transferred to isothermal experiments, in which the whole heat treatment cycle was performed in a differential scanning calorimeter. The Al-Mg-Si-wrought alloy 6005A was investigated. Solution annealing at 540 °C and overcritical quenching to several temperatures between 450 °C and 250 °C were followed by isothermal soaking. Based on the heat flow curves during isothermal soaking, TTP diagrams were determined. An appropriate evaluation method has been developed. It was found that three different precipitation reactions in characteristic temperature intervals exist. Some of the low temperature reactions are not accessible in continuous cooling experiments and require isothermal studies. PMID:28788587

Isothermal Time-Temperature-Precipitation Diagram for an Aluminum Alloy 6005A by In Situ DSC Experiments.

PubMed

Milkereit, Benjamin; Giersberg, Lydia; Kessler, Olaf; Schick, Christoph

2014-03-28

Time-temperature-precipitation (TTP) diagrams deliver important material data, such as temperature and time ranges critical for precipitation during the quenching step of the age hardening procedure. Although the quenching step is continuous, isothermal TTP diagrams are often applied. Together with a so-called Quench Factor Analysis, they can be used to describe very different cooling paths. Typically, these diagrams are constructed based on mechanical properties or microstructures after an interrupted quenching, i.e ., ex situ analyses. In recent years, an in situ calorimetric method to record continuous cooling precipitation diagrams of aluminum alloys has been developed to the application level by our group. This method has now been transferred to isothermal experiments, in which the whole heat treatment cycle was performed in a differential scanning calorimeter. The Al-Mg-Si-wrought alloy 6005A was investigated. Solution annealing at 540 °C and overcritical quenching to several temperatures between 450 °C and 250 °C were followed by isothermal soaking. Based on the heat flow curves during isothermal soaking, TTP diagrams were determined. An appropriate evaluation method has been developed. It was found that three different precipitation reactions in characteristic temperature intervals exist. Some of the low temperature reactions are not accessible in continuous cooling experiments and require isothermal studies.

Split Flow Online Solid-Phase Extraction Coupled with Inductively Coupled Plasma Mass Spectrometry System for One-Shot Data Acquisition of Quantification and Recovery Efficiency.

PubMed

Furukawa, Makoto; Takagai, Yoshitaka

2016-10-04

Online solid-phase extraction (SPE) coupled with inductively coupled plasma mass spectrometry (ICPMS) is a useful tool in automatic sequential analysis. However, it cannot simultaneously quantify the analytical targets and their recovery percentages (R%) in one-shot samples. We propose a system that simultaneously acquires both data in a single sample injection. The main flowline of the online solid-phase extraction is divided into main and split flows. The split flow line (i.e., bypass line), which circumvents the SPE column, was placed on the main flow line. Under program-controlled switching of the automatic valve, the ICPMS sequentially measures the targets in a sample before and after column preconcentration and determines the target concentrations and the R% on the SPE column. This paper describes the system development and two demonstrations to exhibit the analytical significance, i.e., the ultratrace amounts of radioactive strontium ( 90 Sr) using commercial Sr-trap resin and multielement adsorbability on the SPE column. This system is applicable to other flow analyses and detectors in online solid phase extraction.

Low-pressure sequential compression of lower limbs enhances forearm skin blood flow.

PubMed

Amah, Guy; Voicu, Sebastian; Bonnin, Philippe; Kubis, Nathalie

2016-12-01

We investigated whether forearm skin blood flow could be improved when a multilayer pulsatile inflatable suit was applied at a low pressure to the lower limbs and abdomen. We hypothesized that a non-invasive purely mechanical stimulation of the lower limbs could induce remote forearm blood flow modifications. The pulsatile suit induced a sequential compartmentalized low compression (65 mmHg), which was synchronized with each diastole of the cardiac cycle with each phase evolving centripetally (lower limbs to abdomen). Modifications of the forearm skin blood flow were continuously recorded by laser Doppler flowmetry (LDF) at baseline and during the pulsatile suit application. Endothelium-dependent and endothelium-independent vasodilations of the forearm skin microcirculation were measured by LDF in response to a local transdermal iontophoretic application of acetylcholine (ACh-test) and to hyperthermia (hyperT- test). Twenty-four healthy volunteers, 12 men and 12 women (43±14 years) were included in the study. LDF responses increased 1) under pulsatile suit (97±106%, p.

Numerical bifurcation analysis of two coupled FitzHugh-Nagumo oscillators

NASA Astrophysics Data System (ADS)

Hoff, Anderson; dos Santos, Juliana V.; Manchein, Cesar; Albuquerque, Holokx A.

2014-07-01

The behavior of neurons can be modeled by the FitzHugh-Nagumo oscillator model, consisting of two nonlinear differential equations, which simulates the behavior of nerve impulse conduction through the neuronal membrane. In this work, we numerically study the dynamical behavior of two coupled FitzHugh-Nagumo oscillators. We consider unidirectional and bidirectional couplings, for which Lyapunov and isoperiodic diagrams were constructed calculating the Lyapunov exponents and the number of the local maxima of a variable in one period interval of the time-series, respectively. By numerical continuation method the bifurcation curves are also obtained for both couplings. The dynamics of the networks here investigated are presented in terms of the variation between the coupling strength of the oscillators and other parameters of the system. For the network of two oscillators unidirectionally coupled, the results show the existence of Arnold tongues, self-organized sequentially in a branch of a Stern-Brocot tree and by the bifurcation curves it became evident the connection between these Arnold tongues with other periodic structures in Lyapunov diagrams. That system also presents multistability shown in the planes of the basin of attractions.

Experimental and theoretical study of pure and doped crystals: Gd2O2S, Gd2O2S:Eu3+ and Gd2O2S:Tb3+

NASA Astrophysics Data System (ADS)

Wang, Fei; Chen, Xiumin; Liu, Dachun; Yang, Bin; Dai, Yongnian

2012-08-01

Quantum chemistry and experimental method were used to study on pure and doped Gd2O2S crystals in this paper. The band structure and DOS diagrams of pure and doped Gd2O2S crystals which calculated by using DFT (Density Functional Theory) method were illustrated to explain the luminescent properties of impurities in crystals. The calculations of the crystal structure were finished by using the program of CASTEP (Cambridge Sequential Total Energy Package). The samples showed the characteristic emissions of Tb3+ ions with 5D4-7FJ transitions and Eu3+ ions with 5D0-7FJ transitions which emit pure green luminescence and red luminescence respectively. The experimental excitation spectra of Tb3+ and Eu3+ doped Gd2O2S are in agreement of the DOS diagrams over the explored energy range, which has allowed a better understanding of different luminescence mechanisms of Tb3+ and Eu3+ in Gd2O2S crystals.

Testing paleointensity determinations on recent lava flows and scorias from Miyakejima, Japan

NASA Astrophysics Data System (ADS)

Fukuma, K.

2013-12-01

Still no consensus has been reached on paleointensity method. Even the classical Thellier method has not been fully tested on recent lava flows with known geomagnetic field intensity based on a systematic sampling scheme. In this study, Thellier method was applied for 1983, 1962 and 1940 basaltic lava flows and scorias from Miyakejima, Japan. Several vertical lava sections and quenched scorias, which are quite variable in magnetic mineralogy and grain size, provide an unparalleled opportunity to test paleointensity methods. Thellier experiments were conducted on a completely automated three-component spinner magnetometer with thermal demagnetizer 'tspin'. Specimens were heated in air, applied laboratory field was 45 microT, and pTRM checks were performed at every two heating steps. Curie points and hysteresis properties were obtained on small fragments removed from cylindrical specimens. For lava flows sigmoidal curves were commonly observed on the Arai diagrams. Especially the interior part of lava flows always revealed sigmoidal patterns and sometimes resulted in erroneously blurred behaviors. The directions after zero-field heating were not necessarily stable in the course of the Thellier experiments. It was very difficult, for the interior part, to ascertain linear segments on Arai diagrams corresponding to the geomagnetic field intensity at the eruption. Upper and lower clinker samples also generally revealed sigmoidal or upward concave curves on Arai diagrams. Neither lower nor higher temperature portions of the sigmoids or concaves gave the expected geomagnetic field intensities. However, there were two exceptional cases of lava flows giving correct field intensities: upper clinkers with relatively low unblocking temperatures (< 400 deg.C) and lower clinkers with broad unblocking temperature ranges from room temperature to 600 deg.C. A most promising target for paleointensity experiments within the volcanic rocks is scoria. Scoria samples always carry single Curie temperatures higher than 500 deg.C, and the ratios of saturation remanence to saturation magnetization (Mr/Ms) of about 0.5 are indicative of truly single-domain low-titanium titanomagnetite. Unambiguous straight lines were always observed on Arai diagrams covering broad temperature ranges like the lower clinker samples, and the gradients gave the expected field values within a few percent errors. Thellier experiments applied for the recent lava flows did not successfully recover the expected field intensity from most samples. No linear segment was recognized or incorrect paleointensity values were obtained from short segments with limited temperature ranges. In Thellier or other types of paleointensity experiments laboratory alteration is checked in details, but if a sample once passed the alteration check, the TRM/NRM ratios of any limited temperature or field ranges were accepted as reflecting paleointensity. Previously published paleointensity data from lava flows should include much of such dubious data. Generally lava flows are not suitable for paleointensity determinations in light of its large grain-size and mixed magnetic mineralogy, except for scoria and clinker.

Representing object oriented specifications and designs with extended data flow notations

NASA Technical Reports Server (NTRS)

Buser, Jon Franklin; Ward, Paul T.

1988-01-01

The issue of using extended data flow notations to document object oriented designs and specifications is discussed. Extended data flow notations, for the purposes here, refer to notations that are based on the rules of Yourdon/DeMarco data flow analysis. The extensions include additional notation for representing real-time systems as well as some proposed extensions specific to object oriented development. Some advantages of data flow notations are stated. How data flow diagrams are used to represent software objects are investigated. Some problem areas with regard to using data flow notations for object oriented development are noted. Some initial solutions to these problems are proposed.

Hydrological regionalisation based on available hydrological information for runoff prediction at catchment scale

NASA Astrophysics Data System (ADS)

Li, Qiaoling; Li, Zhijia; Zhu, Yuelong; Deng, Yuanqian; Zhang, Ke; Yao, Cheng

2018-06-01

Regionalisation provides a way of transferring hydrological information from gauged to ungauged catchments. The past few decades has seen several kinds of regionalisation approaches for catchment classification and runoff predictions. The underlying assumption is that catchments having similar catchment properties are hydrological similar. This requires the appropriate selection of catchment properties, particularly the inclusion of observed hydrological information, to explain the similarity of hydrological behaviour. We selected observable catchments properties and flow duration curves to reflect the hydrological behaviour, and to regionalize rainfall-runoff response for runoff prediction. As a case study, we investigated 15 catchments located in the Yangtze and Yellow River under multiple hydro-climatic conditions. A clustering scheme was developed to separate the catchments into 4 homogeneous regions by employing catchment properties including hydro-climatic attributes, topographic attributes and land cover etc. We utilized daily flow duration curves as the indicator of hydrological response and interpreted hydrological similarity by root mean square errors. The combined analysis of similarity in catchment properties and hydrological response suggested that catchments in the same homogenous region were hydrological similar. A further validation was conducted by establishing a rainfall-runoff coaxial correlation diagram for each catchment. A common coaxial correlation diagram was generated for each homogenous region. The performances of most coaxial correlation diagrams met the national standard. The coaxial correlation diagram can be transferred within the homogeneous region for runoff prediction in ungauged catchments at an hourly time scale.

Environmental Control Systems

NASA Technical Reports Server (NTRS)

Rosenbush, F. M.

1982-01-01

Materials illustrating a presentation on environment control systems for electric flight systems are presented. Schematics and flow diagrams of fresh air source and air conditioning systems, and vapor cycle and air cycle parts lists are presented.

7 CFR 3430.702 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-01-01

... original manufacturing process (42 U.S.C. 6903 (19)). Recycling means the series of activities, including... process flow diagrams and mass and energy balances for the purposes of scaling up to a demonstration scale...

7 CFR 3430.702 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-01-01

... original manufacturing process (42 U.S.C. 6903 (19)). Recycling means the series of activities, including... process flow diagrams and mass and energy balances for the purposes of scaling up to a demonstration scale...

7 CFR 3430.702 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-01-01

... original manufacturing process (42 U.S.C. 6903 (19)). Recycling means the series of activities, including... process flow diagrams and mass and energy balances for the purposes of scaling up to a demonstration scale...

What Diagrams Argue in Late Imperial Chinese Combinatorial Texts.

PubMed

Bréard, Andrea

2015-01-01

Attitudes towards diagrammatic reasoning and visualization in mathematics were seldom spelled out in texts from pre-modern China, although illustrations figure prominently in mathematical literature since the eleventh century. Taking the sums of finite series and their combinatorial interpretation as a case study, this article investigates the epistemological function of illustrations from the eleventh to the nineteenth century that encode either the mathematical objects themselves or represent their related algorithms. It particularly focuses on the two illustrations given in Wang Lai's (1768-1813) Mathematical Principles of Sequential Combinations, arguing that they reflect a specific mode of nineteenth-century mathematical argumentative practice and served as a heuristic model for later authors.

Transport induced by mean-eddy interaction: II. Analysis of transport processes

NASA Astrophysics Data System (ADS)

Ide, Kayo; Wiggins, Stephen

2015-03-01

We present a framework for the analysis of transport processes resulting from the mean-eddy interaction in a flow. The framework is based on the Transport Induced by the Mean-Eddy Interaction (TIME) method presented in a companion paper (Ide and Wiggins, 2014) [1]. The TIME method estimates the (Lagrangian) transport across stationary (Eulerian) boundaries defined by chosen streamlines of the mean flow. Our framework proceeds after first carrying out a sequence of preparatory steps that link the flow dynamics to the transport processes. This includes the construction of the so-called "instantaneous flux" as the Hovmöller diagram. Transport processes are studied by linking the signals of the instantaneous flux field to the dynamical variability of the flow. This linkage also reveals how the variability of the flow contributes to the transport. The spatio-temporal analysis of the flux diagram can be used to assess the efficiency of the variability in transport processes. We apply the method to the double-gyre ocean circulation model in the situation where the Rossby-wave mode dominates the dynamic variability. The spatio-temporal analysis shows that the inter-gyre transport is controlled by the circulating eddy vortices in the fast eastward jet region, whereas the basin-scale Rossby waves have very little impact.

A graphically oriented specification language for automatic code generation. GRASP/Ada: A Graphical Representation of Algorithms, Structure, and Processes for Ada, phase 1

NASA Technical Reports Server (NTRS)

Cross, James H., II; Morrison, Kelly I.; May, Charles H., Jr.; Waddel, Kathryn C.

1989-01-01

The first phase of a three-phase effort to develop a new graphically oriented specification language which will facilitate the reverse engineering of Ada source code into graphical representations (GRs) as well as the automatic generation of Ada source code is described. A simplified view of the three phases of Graphical Representations for Algorithms, Structure, and Processes for Ada (GRASP/Ada) with respect to three basic classes of GRs is presented. Phase 1 concentrated on the derivation of an algorithmic diagram, the control structure diagram (CSD) (CRO88a) from Ada source code or Ada PDL. Phase 2 includes the generation of architectural and system level diagrams such as structure charts and data flow diagrams and should result in a requirements specification for a graphically oriented language able to support automatic code generation. Phase 3 will concentrate on the development of a prototype to demonstrate the feasibility of this new specification language.

78 FR 59647 - Submission for OMB Review; Comment Request

Federal Register 2010, 2011, 2012, 2013, 2014

2013-09-27

... plan for restricting collection or dissemination of imagery of Israeli territory, data flow diagram and... and international obligations of the United States. The requirements are contained in 15 CFR part 960...

Possible Aural Activities in the Listening Class.

ERIC Educational Resources Information Center

Zhiqian, Wu

1989-01-01

Some aural activities are described that can help language students with their listening comprehension. They include dictation, a "who am I?" exercise, sketch-drawing, chart completion, a comparison exercise, and a flow diagram. (LB)

Performance of single-stage compressor designed on basis of constant total enthalpy with symmetrical velocity diagram at all radii and velocity ratio of 0.7 at rotor hub / Jack R. Burtt and Robert J. Jackson

NASA Technical Reports Server (NTRS)

Burtt, Jack R; Jackson, Robert J

1951-01-01

A typical inlet axial-flow compressor inlet stage, which was designed on the basis of constant total enthalpy with symmetrical velocity diagram at all radii, was investigated. At a tip speed of 1126 feet per second, a peak pressure ratio of 1.28 was obtained at an efficiency of 0.76. At a tip speed, the highest practical flow was 28 pounds per second per square foot frontal area with an efficiency of 0.78. Data for a rotor relative inlet Mach number range of from 0.5 to 0.875 indicates that the critical value for any stage radial element is approximately 0.80 for the stage investigated.

A new car-following model for autonomous vehicles flow with mean expected velocity field

NASA Astrophysics Data System (ADS)

Wen-Xing, Zhu; Li-Dong, Zhang

2018-02-01

Due to the development of the modern scientific technology, autonomous vehicles may realize to connect with each other and share the information collected from each vehicle. An improved forward considering car-following model was proposed with mean expected velocity field to describe the autonomous vehicles flow behavior. The new model has three key parameters: adjustable sensitivity, strength factor and mean expected velocity field size. Two lemmas and one theorem were proven as criteria for judging the stability of homogeneousautonomous vehicles flow. Theoretical results show that the greater parameters means larger stability regions. A series of numerical simulations were carried out to check the stability and fundamental diagram of autonomous flow. From the numerical simulation results, the profiles, hysteresis loop and density waves of the autonomous vehicles flow were exhibited. The results show that with increased sensitivity, strength factor or field size the traffic jam was suppressed effectively which are well in accordance with the theoretical results. Moreover, the fundamental diagrams corresponding to three parameters respectively were obtained. It demonstrates that these parameters play almost the same role on traffic flux: i.e. before the critical density the bigger parameter is, the greater flux is and after the critical density, the opposite tendency is. In general, the three parameters have a great influence on the stability and jam state of the autonomous vehicles flow.

Eyewitness decisions in simultaneous and sequential lineups: a dual-process signal detection theory analysis.

PubMed

Meissner, Christian A; Tredoux, Colin G; Parker, Janat F; MacLin, Otto H

2005-07-01

Many eyewitness researchers have argued for the application of a sequential alternative to the traditional simultaneous lineup, given its role in decreasing false identifications of innocent suspects (sequential superiority effect). However, Ebbesen and Flowe (2002) have recently noted that sequential lineups may merely bring about a shift in response criterion, having no effect on discrimination accuracy. We explored this claim, using a method that allows signal detection theory measures to be collected from eyewitnesses. In three experiments, lineup type was factorially combined with conditions expected to influence response criterion and/or discrimination accuracy. Results were consistent with signal detection theory predictions, including that of a conservative criterion shift with the sequential presentation of lineups. In a fourth experiment, we explored the phenomenological basis for the criterion shift, using the remember-know-guess procedure. In accord with previous research, the criterion shift in sequential lineups was associated with a reduction in familiarity-based responding. It is proposed that the relative similarity between lineup members may create a context in which fluency-based processing is facilitated to a greater extent when lineup members are presented simultaneously.

An Experimental Investigation of Flow Conditions in the Vicinity of an NACA D(sub S)-type Cowling

NASA Technical Reports Server (NTRS)

Bryant, Rosemary P.; Boswinkle, Robert W.

1946-01-01

Data are presented of the flow conditions in the vicinity of an NACA D sub S -type cowling. Tests were made of a 1/2 scale-nacelle model at inlet-velocity ratios ranging from 0.23 to 1.02 and angles of attack from 6 deg to 10 deg. The velocity and direction of flow in the vertical plane of symmetry of the cowling were determined from orifices and tufts installed on a board aligned with the flow. Diagrams showing velocity ratio contours and lines of constant flow angles are given.

Generalized serial search code acquisition - The equivalent circular state diagram approach

NASA Technical Reports Server (NTRS)

Polydoros, A.; Simon, M. K.

1984-01-01

A transform-domain method for deriving the generating function of the acquisition process resulting from an arbitrary serial search strategy is presented. The method relies on equivalent circular state diagrams, uses Mason's formula from flow-graph theory, and employs a minimum number of required parameters. The transform-domain approach is briefly described and the concept of equivalent circular state diagrams is introduced and exploited to derive the generating function and resulting mean acquisition time for three particular cases of interest, the continuous/center Z search, the broken/center Z search, and the expanding window search. An optimization of the latter technique is performed whereby the number of partial windows which minimizes the mean acquisition time is determined. The numerical results satisfy certain intuitive predictions and provide useful design guidelines for such systems.

Leeward flow over delta wings at supersonic speeds

NASA Technical Reports Server (NTRS)

Szodruch, J. G.

1980-01-01

A survey was made of the parameters affecting the development of the leeward symmetric separated flow over slender delta wings immersed in a supersonic stream. The parameters included Mach number, Reynolds number, angle of attack, leading-edge sweep angle, and body cross-sectional shape, such that subsonic and supersonic leading-edge flows are encountered. It was seen that the boundaries between the various flow regimes existing about the leeward surface may conveniently be represented on a diagram with the components of angle of attack and Mach number normal to the leading edge as governing parameters.

Improved method for calibration of exchange flows for a physical transport box model of Tampa Bay, FL USA

EPA Science Inventory

Results for both sequential and simultaneous calibration of exchange flows between segments of a 10-box, one-dimensional, well-mixed, bifurcated tidal mixing model for Tampa Bay are reported. Calibrations were conducted for three model options with different mathematical expressi...

Optimization of Multiple Related Negotiation through Multi-Negotiation Network

NASA Astrophysics Data System (ADS)

Ren, Fenghui; Zhang, Minjie; Miao, Chunyan; Shen, Zhiqi

In this paper, a Multi-Negotiation Network (MNN) and a Multi- Negotiation Influence Diagram (MNID) are proposed to optimally handle Multiple Related Negotiations (MRN) in a multi-agent system. Most popular, state-of-the-art approaches perform MRN sequentially. However, a sequential procedure may not optimally execute MRN in terms of maximizing the global outcome, and may even lead to unnecessary losses in some situations. The motivation of this research is to use a MNN to handle MRN concurrently so as to maximize the expected utility of MRN. Firstly, both the joint success rate and the joint utility by considering all related negotiations are dynamically calculated based on a MNN. Secondly, by employing a MNID, an agent's possible decision on each related negotiation is reflected by the value of expected utility. Lastly, through comparing expected utilities between all possible policies to conduct MRN, an optimal policy is generated to optimize the global outcome of MRN. The experimental results indicate that the proposed approach can improve the global outcome of MRN in a successful end scenario, and avoid unnecessary losses in an unsuccessful end scenario.

On understanding nuclear reaction network flows with branchings on directed graphs

NASA Astrophysics Data System (ADS)

Meyer, Bradley S.

2018-04-01

Nuclear reaction network flow diagrams are useful for understanding which reactions are governing the abundance changes at a particular time during nucleosynthesis. This is especially true when the flows are largely unidirectional, such as during the s-process of nucleosynthesis. In explosive nucleosynthesis, when reaction flows are large, and when forward reactions are nearly balanced by their reverses, reaction flows no longer give a clear picture of the abundance evolution in the network. This paper presents a way of understanding network evolution in terms of sums of branchings on a directed graph, which extends the concept of reaction flows to allow for multiple reaction pathways.

Computational test bench and flow chart for wavefront sensors

NASA Astrophysics Data System (ADS)

Abecassis, Úrsula V.; de Lima Monteiro, Davies W.; Salles, Luciana P.; Stanigher, Rafaela; Borges, Euller

2014-05-01

The wavefront reconstruction diagram has come to supply the need in literature of an ampler vision over the many methods and optronic devices used for the reconstruction of wavefronts and to show the existing interactions between those. A computational platform has been developed using the diagram's orientation for the taking of decision over the best technique and the photo sensible and electronic structures to be implemented. This work will be directed to an ophthalmological application in the development of an instrument of help for the diagnosis of optical aberrations of the human eye.

Ground-Based Photometric Measurements HAES Program Support.

DTIC Science & Technology

1979-01-31

photometric system such as the MTP can be optimized to a certain extent, but the fundamental limitations on 16 A z I- z -e 0 / LUJ LU z 00 04 LUL 0’ -1...Introduction 12 2.2 Background and Relevance 12 2.3 Measurement Requirements 15 2.4 MTP Optical Design 16 2.5 Digital Photon-Counting Data System 19 2.6...optical head 17 3 Block diagram of modular photometer, digital data and control systems 20 4 Flow diagram of computer program used to analyze three beam

REML/BLUP and sequential path analysis in estimating genotypic values and interrelationships among simple maize grain yield-related traits.

PubMed

Olivoto, T; Nardino, M; Carvalho, I R; Follmann, D N; Ferrari, M; Szareski, V J; de Pelegrin, A J; de Souza, V Q

2017-03-22

Methodologies using restricted maximum likelihood/best linear unbiased prediction (REML/BLUP) in combination with sequential path analysis in maize are still limited in the literature. Therefore, the aims of this study were: i) to use REML/BLUP-based procedures in order to estimate variance components, genetic parameters, and genotypic values of simple maize hybrids, and ii) to fit stepwise regressions considering genotypic values to form a path diagram with multi-order predictors and minimum multicollinearity that explains the relationships of cause and effect among grain yield-related traits. Fifteen commercial simple maize hybrids were evaluated in multi-environment trials in a randomized complete block design with four replications. The environmental variance (78.80%) and genotype-vs-environment variance (20.83%) accounted for more than 99% of the phenotypic variance of grain yield, which difficult the direct selection of breeders for this trait. The sequential path analysis model allowed the selection of traits with high explanatory power and minimum multicollinearity, resulting in models with elevated fit (R 2 > 0.9 and ε < 0.3). The number of kernels per ear (NKE) and thousand-kernel weight (TKW) are the traits with the largest direct effects on grain yield (r = 0.66 and 0.73, respectively). The high accuracy of selection (0.86 and 0.89) associated with the high heritability of the average (0.732 and 0.794) for NKE and TKW, respectively, indicated good reliability and prospects of success in the indirect selection of hybrids with high-yield potential through these traits. The negative direct effect of NKE on TKW (r = -0.856), however, must be considered. The joint use of mixed models and sequential path analysis is effective in the evaluation of maize-breeding trials.

37 CFR 1.58 - Chemical and mathematical formulae and tables.

Code of Federal Regulations, 2011 CFR

2011-07-01

..., including the claims, may contain chemical and mathematical formulae, but shall not contain drawings or flow diagrams. The description portion of the specification may contain tables, but the same tables may only be...

40 CFR 270.24 - Specific part B information requirements for process vents.

Code of Federal Regulations, 2011 CFR

2011-07-01

... emission reductions must be made using operating parameter values (e.g., temperatures, flow rates, or..., schematics, and piping and instrumentation diagrams based on the appropriate sections of “APTI Course 415...

40 CFR 270.24 - Specific part B information requirements for process vents.

Code of Federal Regulations, 2013 CFR

2013-07-01

... emission reductions must be made using operating parameter values (e.g., temperatures, flow rates, or..., schematics, and piping and instrumentation diagrams based on the appropriate sections of “APTI Course 415...

40 CFR 60.103a - Work practice standards.

Code of Federal Regulations, 2010 CFR

2010-07-01

... becomes an affected flare subject to this subpart. The plan must include: (1) A diagram illustrating all connections to the flare; (2) Methods for monitoring flow rate to the flare, including a detailed description...

40 CFR 270.24 - Specific part B information requirements for process vents.

Code of Federal Regulations, 2012 CFR

2012-07-01

... emission reductions must be made using operating parameter values (e.g., temperatures, flow rates, or..., schematics, and piping and instrumentation diagrams based on the appropriate sections of “APTI Course 415...

40 CFR 270.24 - Specific part B information requirements for process vents.

Code of Federal Regulations, 2014 CFR

2014-07-01

... emission reductions must be made using operating parameter values (e.g., temperatures, flow rates, or..., schematics, and piping and instrumentation diagrams based on the appropriate sections of “APTI Course 415...

37 CFR 1.58 - Chemical and mathematical formulae and tables.

Code of Federal Regulations, 2014 CFR

2014-07-01

..., including the claims, may contain chemical and mathematical formulae, but shall not contain drawings or flow diagrams. The description portion of the specification may contain tables, but the same tables should not...

40 CFR 60.103a - Work practice standards.

Code of Federal Regulations, 2012 CFR

2012-07-01

... becomes an affected flare subject to this subpart. The plan must include: (1) A diagram illustrating all connections to the flare; (2) Methods for monitoring flow rate to the flare, including a detailed description...

37 CFR 1.58 - Chemical and mathematical formulae and tables.

Code of Federal Regulations, 2013 CFR

2013-07-01

..., including the claims, may contain chemical and mathematical formulae, but shall not contain drawings or flow diagrams. The description portion of the specification may contain tables, but the same tables may only be...

Space shuttle on-orbit flight control software requirements, preliminary version

NASA Technical Reports Server (NTRS)

1975-01-01

Software modules associated with various flight control functions for the space shuttle orbiter are described. Data flow, interface requirements, initialization requirements and module sequencing requirements are considered. Block diagrams and tables are included.

Laser anemometry for hot flows

NASA Astrophysics Data System (ADS)

Kugler, P.; Langer, G.

1987-07-01

The fundamental principles, instrumentation, and practical operation of LDA and laser-transit-anemometry systems for measuring velocity profiles and the degree of turbulence in high-temperature flows are reviewed and illustrated with diagrams, drawings and graphs of typical data. Consideration is given to counter, tracker, spectrum-analyzer and correlation methods of LDA signal processing; multichannel analyzer and cross correlation methods for LTA data; LTA results for a small liquid fuel rocket motor; and experiments demonstrating the feasibility of an optoacoustic demodulation scheme for LDA signals from unsteady flows.

Glutamate Receptor Aptamers and ALS

DTIC Science & Technology

2008-01-01

XXGATC ACC Consensus sequence RNA library Cloning and sequencing SELEX DIAGRAM Fig. 1. (a) Flow chart of SELEX. The library we used for SELEX...recording electrode and placed ~100 µm away from the hole. The linear flow rate of the solution is 1-4 cm/s. An optical fiber through which laser light for...channel recording (26) GluR6Q 1.1 × 104 4.2 × 102 Laser-pulse photolysis (67) 1.0 × 104 4.4 × 102 Fitting (52) 1.0 × 104 Flow measurement (46

Three-dimensional quantitative flow diagnostics

NASA Technical Reports Server (NTRS)

Miles, Richard B.; Nosenchuck, Daniel M.

1989-01-01

The principles, capabilities, and practical implementation of advanced measurement techniques for the quantitative characterization of three-dimensional flows are reviewed. Consideration is given to particle, Rayleigh, and Raman scattering; fluorescence; flow marking by H2 bubbles, photochromism, photodissociation, and vibrationally excited molecules; light-sheet volume imaging; and stereo imaging. Also discussed are stereo schlieren methods, holographic particle imaging, optical tomography, acoustic and magnetic-resonance imaging, and the display of space-filling data. Extensive diagrams, graphs, photographs, sample images, and tables of numerical data are provided.

Geochemical evidence for Late Cretaceous marginal arc-to-backarc transition in the Sabzevar ophiolitic extrusive sequence, northeast Iran

NASA Astrophysics Data System (ADS)

Khalatbari Jafari, Morteza; Babaie, Hassan A.; Gani, Moslem

2013-07-01

The ophiolitic extrusive sequence, exposed in an area north of Sabzevar, has three major parts: a lower part, with abundant breccia, hyaloclastic tuff, and sheet flow, a middle part with vesicular, aphyric pillow lava, and an upper part with a sequence of lava and volcanic-sedimentary rocks. Pelagic limestone interlayers contain Late Cretaceous (Maastrichtian-Late Maastrichtian) microfauna. The supra-ophiolitic series includes a sequence of turbidititic and volcanic-sedimentary rocks with lava flow, aphyric and phyric lava, and interlayers of pelagic limestone and radiolarian chert. Paleontological investigation of the pelagic limestone and radiolarite interlayers in this series gives a Late Cretaceous age, supporting the idea that the supra-ophiolitic series formed in a trough, synchronous with the Sabzevar oceanic crust during the Late Cretaceous. Geochemical data indicate a relationship between lava in the upper part of the extrusive sequence and lava in the supra-ophiolitic series. These lavas have a calc-alkaline to almost alkaline characteristic, and show a clear depletion in Nb and definite depletions in Zr and Ti in spider diagrams. Data from these rocks plot in the subduction zone field in tectonomagmatic diagrams. The concentration and position of the heavy rare earth elements in the spider diagrams, and their slight variation, can be attributed to partial melting of the depleted mantle wedge above the subducted slab, and enrichment in the LILE can be attributed to subduction components (fluid, melt) released from the subducting slab. In comparison, the sheet flow and pillow lava of the lower and middle parts of the extrusive sequence show OIB characteristics and high potassium magmatic and shoshonitic trends, and their spider diagram patterns show Nb, Zr, and Ti depletions. The enrichment in the LILE in the spider diagram patterns suggest a low rate of partial melting of an enriched, garnet-bearing mantle. It seems that the marginal arc basin, in which the Sabzevar ophiolite was forming, experienced lithospheric extension in response to slab rollback. This process, which formed a backarc basin, may have aborted the embryonic arc, stopped arc magmatism, and led to the rise of mantle diapirs. The extrusive ophiolite sequence, north of Sabzevar probably formed during the transition from a marginal arc basin to a backarc basin during the Late Cretaceous.

46 CFR 162.050-17 - Separator test rig.

Code of Federal Regulations, 2014 CFR

2014-10-01

... diagram of a typical test rig is shown in Figure 162.050-17(a). FIGURE 162.050-17(a)—SEPARATOR TEST RIG... discharge side. (c) The inlet piping of the test rig must be sized so that— (1) Influent water flows at a Reynolds Number of at least 10,000; (2) The influent flow rate is between one and three meters per second...

Unsteady transonic flows - Introduction, current trends, applications

NASA Technical Reports Server (NTRS)

Yates, E. C., Jr.

1985-01-01

The computational treatment of unsteady transonic flows is discussed, reviewing the historical development and current techniques. The fundamental physical principles are outlined; the governing equations are introduced; three-dimensional linearized and two-dimensional linear-perturbation theories in frequency domain are described in detail; and consideration is given to frequency-domain FEMs and time-domain finite-difference and integral-equation methods. Extensive graphs and diagrams are included.

46 CFR 162.050-17 - Separator test rig.

Code of Federal Regulations, 2011 CFR

2011-10-01

... diagram of a typical test rig is shown in Figure 162.050-17(a). FIGURE 162.050-17(a)—SEPARATOR TEST RIG... discharge side. (c) The inlet piping of the test rig must be sized so that— (1) Influent water flows at a Reynolds Number of at least 10,000; (2) The influent flow rate is between one and three meters per second...

46 CFR 162.050-17 - Separator test rig.

Code of Federal Regulations, 2010 CFR

2010-10-01

... diagram of a typical test rig is shown in Figure 162.050-17(a). FIGURE 162.050-17(a)—SEPARATOR TEST RIG... discharge side. (c) The inlet piping of the test rig must be sized so that— (1) Influent water flows at a Reynolds Number of at least 10,000; (2) The influent flow rate is between one and three meters per second...

46 CFR 162.050-17 - Separator test rig.

Code of Federal Regulations, 2013 CFR

2013-10-01

... diagram of a typical test rig is shown in Figure 162.050-17(a). FIGURE 162.050-17(a)—SEPARATOR TEST RIG... discharge side. (c) The inlet piping of the test rig must be sized so that— (1) Influent water flows at a Reynolds Number of at least 10,000; (2) The influent flow rate is between one and three meters per second...

46 CFR 162.050-17 - Separator test rig.

Code of Federal Regulations, 2012 CFR

2012-10-01

... diagram of a typical test rig is shown in Figure 162.050-17(a). FIGURE 162.050-17(a)—SEPARATOR TEST RIG... discharge side. (c) The inlet piping of the test rig must be sized so that— (1) Influent water flows at a Reynolds Number of at least 10,000; (2) The influent flow rate is between one and three meters per second...

[Modeling the requirements on routine data of general practitioners from the health-care researcher's point of view with the help of unified modeling langauge (UML)].

PubMed

Kersting, M; Hauswaldt, J; Lingner, H

2012-08-01

Health-care research is, besides primary acquired study data, based on data from widely differing secondary sources. In order to link, compare and analyze data sources uniform models and methods are needed. This could be facilitated by a more structured description of requirements, models and methods of health-care research than those currently used. Suitable methods of presentation were sought in an approach to this target and the unified modeling language (UML) identified as a possible alternative. Using different tools 3 UML diagrams were created to represent some individual aspects of a scientific use file (SUF): A use case diagram as well as an activity and a class diagram. In the use case diagram we attempted to represent the general use cases of an SUF based on general practitioners routine data. Secondly a class diagram was constructed to visualize the contents and structure of a SUF. Thirdly an activity diagram was developed to graphically represent the concept of a general practitioner's episode of care. The creation of the UML diagrams was possible without any technical difficulties. Regarding the content the 3 diagrams must still be considered as prototypes. The use case diagram shows possible uses and users of an SUF, e. g. a research worker, industry but also the general practitioner who supplies the data. The class diagram reveals a general data structure that can serve information processes in practice and research. Besides aggregation, possibilities for specialization and generalization are essential elements of the class diagram that can be used meaningfully. The activity diagram for the schematic representation of a general practitioner's episode of care reveals the existence of multiple endpoints of an episode and the possibility to form relationships by means of episodes (diagnosis>therapy). The constructed diagrams are preliminary results and should be refined in future steps. Use case diagrams enable a rapid overview of the meaning and purpose of a system, in this case an SUF. Class diagrams can help at a professional level to describe relationships between entities (classes/objects) more clearly than with the existing methods of representation. Activity diagrams are successors to classic flow charts. They are complemented appropriately by status diagrams. UML is suitable to uniformly and graphically describe a system (here an SUF) from various points of view. In future, validated UML models will help us to present scientific concepts and results in a more structured form than before and to promote the technological use of these concepts in practice. © Georg Thieme Verlag KG Stuttgart · New York.

Patient Safety—Incorporating Drawing Software into Root Cause Analysis Software

PubMed Central

Williams, Linda; Grayson, Diana; Gosbee, John

2001-01-01

Drawing software from Lassalle Technologies1 (France) designed for Visual Basic is the tool we used to standardize the creation, storage, and retrieval of flow diagrams containing information about adverse events and close calls.

Patient Safety—Incorporating Drawing Software into Root Cause Analysis Software

PubMed Central

Williams, Linda; Grayson, Diana; Gosbee, John

2002-01-01

Drawing software from Lassalle Technologies1 (France) designed for Visual Basic is the tool we used to standardize the creation, storage, and retrieval of flow diagrams containing information about adverse events and close calls.

40 CFR 270.305 - What tank information must I keep at my facility?

Code of Federal Regulations, 2011 CFR

2011-07-01

..., bypass systems, and pressure controls (e.g., vents). (d) A diagram of piping, instrumentation, and process flow for each tank system. (e) A description of materials and equipment used to provide external...

40 CFR 270.305 - What tank information must I keep at my facility?

Code of Federal Regulations, 2012 CFR

2012-07-01

..., bypass systems, and pressure controls (e.g., vents). (d) A diagram of piping, instrumentation, and process flow for each tank system. (e) A description of materials and equipment used to provide external...

40 CFR 270.305 - What tank information must I keep at my facility?

Code of Federal Regulations, 2013 CFR

2013-07-01

..., bypass systems, and pressure controls (e.g., vents). (d) A diagram of piping, instrumentation, and process flow for each tank system. (e) A description of materials and equipment used to provide external...

40 CFR 270.305 - What tank information must I keep at my facility?

Code of Federal Regulations, 2014 CFR

2014-07-01

..., bypass systems, and pressure controls (e.g., vents). (d) A diagram of piping, instrumentation, and process flow for each tank system. (e) A description of materials and equipment used to provide external...

A project management system for the X-29A flight test program

NASA Technical Reports Server (NTRS)

Stewart, J. F.; Bauer, C. A.

1983-01-01

The project-management system developed for NASA's participation in the X-29A aircraft development program is characterized from a theoretical perspective, as an example of a system appropriate to advanced, highly integrated technology projects. System-control theory is applied to the analysis of classical project-management techniques and structures, which are found to be of closed-loop multivariable type; and the effects of increasing project complexity and integration are evaluated. The importance of information flow, sampling frequency, information holding, and delays is stressed. The X-29A system is developed in four stages: establishment of overall objectives and requirements, determination of information processes (block diagrams) definition of personnel functional roles and relationships, and development of a detailed work-breakdown structure. The resulting system is shown to require a greater information flow to management than conventional methods. Sample block diagrams are provided.

Stock flow diagram analysis on solid waste management in Malaysia

NASA Astrophysics Data System (ADS)

Zulkipli, Faridah; Nopiah, Zulkifli Mohd; Basri, Noor Ezlin Ahmad; Kie, Cheng Jack

2016-10-01

The effectiveness on solid waste management is a major importance to societies. Numerous generation of solid waste from our daily activities has risked for our communities. These due to rapid population grow and advance in economic development. Moreover, the complexity of solid waste management is inherently involved large scale, diverse and element of uncertainties that must assist stakeholders with deviating objectives. In this paper, we proposed a system dynamics simulation by developing a stock flow diagram to illustrate the solid waste generation process and waste recycle process. The analysis highlights the impact on increasing the number of population toward the amount of solid waste generated and the amount of recycled waste. The results show an increment in the number of population as well as the amount of recycled waste will decrease the amount of waste generated. It is positively represent the achievement of government aim to minimize the amount of waste to be disposed by year 2020.

A theory of rotating stall of multistage axial compressors. III - Limit cycles

NASA Technical Reports Server (NTRS)

Moore, F. K.

1983-01-01

A theory of rotating stall, based on single parameters for blade-passage lag and external-flow lag and a given compressor characteristic yields limit cycles in velocity space. These limit cycles are governed by Lienard's equation with the characteristic playing the role of nonlinear damping function. Cyclic integrals of the solution determine stall propagation speed and the effect of rotating stall on average performance. Solution with various line-segment characteristics and various throttle settings are found and discussed. There is generally a limiting flow coefficient beyond which no solution is possible; this probably represents stall recovery. This recovery point is independent of internal compressor lag, but does depend on external lags and on the height-to-width ratio of the diagram. Tall diagrams and small external lags (inlet and diffusor) favor recovery. Suggestions for future theoretical and experimental research are discussed.

Cross-stream diffusion under pressure-driven flow in microchannels with arbitrary aspect ratios: a phase diagram study using a three-dimensional analytical model

PubMed Central

Song, Hongjun; Wang, Yi; Pant, Kapil

2011-01-01

This article presents a three-dimensional analytical model to investigate cross-stream diffusion transport in rectangular microchannels with arbitrary aspect ratios under pressure-driven flow. The Fourier series solution to the three-dimensional convection–diffusion equation is obtained using a double integral transformation method and associated eigensystem calculation. A phase diagram derived from the dimensional analysis is presented to thoroughly interrogate the characteristics in various transport regimes and examine the validity of the model. The analytical model is verified against both experimental and numerical models in terms of the concentration profile, diffusion scaling law, and mixing efficiency with excellent agreement (with <0.5% relative error). Quantitative comparison against other prior analytical models in extensive parameter space is also performed, which demonstrates that the present model accommodates much broader transport regimes with significantly enhanced applicability. PMID:22247719

Cross-stream diffusion under pressure-driven flow in microchannels with arbitrary aspect ratios: a phase diagram study using a three-dimensional analytical model.

PubMed

Song, Hongjun; Wang, Yi; Pant, Kapil

2012-01-01

This article presents a three-dimensional analytical model to investigate cross-stream diffusion transport in rectangular microchannels with arbitrary aspect ratios under pressure-driven flow. The Fourier series solution to the three-dimensional convection-diffusion equation is obtained using a double integral transformation method and associated eigensystem calculation. A phase diagram derived from the dimensional analysis is presented to thoroughly interrogate the characteristics in various transport regimes and examine the validity of the model. The analytical model is verified against both experimental and numerical models in terms of the concentration profile, diffusion scaling law, and mixing efficiency with excellent agreement (with <0.5% relative error). Quantitative comparison against other prior analytical models in extensive parameter space is also performed, which demonstrates that the present model accommodates much broader transport regimes with significantly enhanced applicability.

A novel visual hardware behavioral language

NASA Technical Reports Server (NTRS)

Li, Xueqin; Cheng, H. D.

1992-01-01

Most hardware behavioral languages just use texts to describe the behavior of the desired hardware design. This is inconvenient for VLSI designers who enjoy using the schematic approach. The proposed visual hardware behavioral language has the ability to graphically express design information using visual parallel models (blocks), visual sequential models (processes) and visual data flow graphs (which consist of primitive operational icons, control icons, and Data and Synchro links). Thus, the proposed visual hardware behavioral language can not only specify hardware concurrent and sequential functionality, but can also visually expose parallelism, sequentiality, and disjointness (mutually exclusive operations) for the hardware designers. That would make the hardware designers capture the design ideas easily and explicitly using this visual hardware behavioral language.

Persistent Step-Flow Growth of Strained Films on Vicinal Substrates

NASA Astrophysics Data System (ADS)

Hong, Wei; Lee, Ho Nyung; Yoon, Mina; Christen, Hans M.; Lowndes, Douglas H.; Suo, Zhigang; Zhang, Zhenyu

2005-08-01

We propose a model of persistent step flow, emphasizing dominant kinetic processes and strain effects. Within this model, we construct a morphological phase diagram, delineating a regime of step flow from regimes of step bunching and island formation. In particular, we predict the existence of concurrent step bunching and island formation, a new growth mode that competes with step flow for phase space, and show that the deposition flux and temperature must be chosen within a window in order to achieve persistent step flow. The model rationalizes the diverse growth modes observed in pulsed laser deposition of SrRuO3 on SrTiO3.

INVESTIGATION OF ARSENIC SPECIATION ON DRINKING WATER TREATMENT MEDIA UTILIZING AUTOMATED SEQUENTIAL CONTINUOUS FLOW EXTRACTION WITH IC-ICP-MS DETECTION

EPA Science Inventory

Three treatment media, used for the removal of arsenic from drinking water, were sequentially extracted using 10mM MgCl2 (pH 8), 10mM NaH2PO4 (pH 7) followed by 10mM (NH4)2C2O4 (pH 3). The media were extracted using an on-line automated continuous extraction system which allowed...

Sequential ensemble-based optimal design for parameter estimation: SEQUENTIAL ENSEMBLE-BASED OPTIMAL DESIGN

DOE Office of Scientific and Technical Information (OSTI.GOV)

Man, Jun; Zhang, Jiangjiang; Li, Weixuan

2016-10-01

The ensemble Kalman filter (EnKF) has been widely used in parameter estimation for hydrological models. The focus of most previous studies was to develop more efficient analysis (estimation) algorithms. On the other hand, it is intuitively understandable that a well-designed sampling (data-collection) strategy should provide more informative measurements and subsequently improve the parameter estimation. In this work, a Sequential Ensemble-based Optimal Design (SEOD) method, coupled with EnKF, information theory and sequential optimal design, is proposed to improve the performance of parameter estimation. Based on the first-order and second-order statistics, different information metrics including the Shannon entropy difference (SD), degrees ofmore » freedom for signal (DFS) and relative entropy (RE) are used to design the optimal sampling strategy, respectively. The effectiveness of the proposed method is illustrated by synthetic one-dimensional and two-dimensional unsaturated flow case studies. It is shown that the designed sampling strategies can provide more accurate parameter estimation and state prediction compared with conventional sampling strategies. Optimal sampling designs based on various information metrics perform similarly in our cases. The effect of ensemble size on the optimal design is also investigated. Overall, larger ensemble size improves the parameter estimation and convergence of optimal sampling strategy. Although the proposed method is applied to unsaturated flow problems in this study, it can be equally applied in any other hydrological problems.« less

Difference in vascular patterns between transosseous-equivalent and transosseous rotator cuff repair.

PubMed

Urita, Atsushi; Funakoshi, Tadanao; Horie, Tatsunori; Nishida, Mutsumi; Iwasaki, Norimasa

2017-01-01

Vascularity is the important factor of biologic healing of the repaired tissue. The purpose of this study was to clarify sequential vascular patterns of repaired rotator cuff by suture techniques. We randomized 21 shoulders in 20 patients undergoing arthroscopic rotator cuff repair into 2 groups: transosseous-equivalent repair (TOE group, n = 10) and transosseous repair (TO group, n = 11). Blood flow in 4 regions inside the cuff (lateral articular, lateral bursal, medial articular, and medial bursal), in the knotless suture anchor in the TOE group, and in the bone tunnel in the TO group was measured using contrast-enhanced ultrasound at 1 month, 2 months, 3 months, and 6 months postoperatively. The sequential vascular pattern inside the repaired rotator cuff was different between groups. The blood flow in the lateral articular area at 1 month, 2 months, and 3 months (P = .002, .005, and .025) and that in the lateral bursal area at 2 months (P = .031) in the TO group were significantly greater than those in the TOE group postoperatively. Blood flow was significantly greater for the bone tunnels in the TO group than for the knotless suture anchor in the TOE group at 1 month and 2 months postoperatively (P = .041 and .009). This study clarified that the sequential vascular pattern inside the repaired rotator cuff depends on the suture technique used. Bone tunnels through the footprint may contribute to biologic healing by increasing blood flow in the repaired rotator cuff. Copyright © 2017 Journal of Shoulder and Elbow Surgery Board of Trustees. Published by Elsevier Inc. All rights reserved.

[Studies on a sequential injection renewable surface reflectance spectrophotometric system using a microchip flow cell].

PubMed

Wang, Jian-ya; Fang, Zhao-lun

2002-02-01

A microchip flow cell was developed for flow injection renewable surface assay by reflectance spectrophotometry. The flow cell was coupled to a sequential injection system and optical fiber photometric detection system. The flow cell featured a three-layer structure. The flow channel was cut into a silicone rubber membrance which formed the middle layer, and a porous filter was inlayed across a widened section of the channel to trap microbeads introduced into the flow cell. The area of the detection window of the flow cell was approximately 3.6 mm2, the volume of the bead trapped in the flow cell was 2.2 microL, the depth of the bead layer was 600 microns. A multistrand bifurcated optical fiber was coupled with incident light, detector and flow cell. The chromogenic reaction of Cr(VI) with 1,5-diphenylcarbohydrazide (DPC) which was adsorbed on trapped Polysorb C-18 beads was used as a model reaction to optimize the flow cell design and the experimental system. The reflectance of the renewable reaction surface was monitored at 540 nm. With 100 microL sample loaded and 1.0 mL.min-1 carrier flow rate, the linear response range was 0-0.6 microgram.mL-1 Cr(VI). A detection limit (3 sigma) of 6 ng.mL-1, precision of 1.5% RSD(n = 11), and a throughput of 64 samples per hour were achieved. Considerations in system and flow cell design, the influence of depth of the bead layer, weight of beads used, and the flow rates of carrier stream on the performance were discussed.

Comparison of intersecting pedestrian flows based on experiments

NASA Astrophysics Data System (ADS)

Zhang, J.; Seyfried, A.

2014-07-01

Intersections of pedestrian flows feature multiple types, varying in the numbers of flow directions as well as intersecting angles. In this article results from intersecting flow experiments with two different intersecting angles are compared. To analyze the transport capabilities the Voronoi method is used to resolve the fine structure of the resulting velocity-density relations and spatial dependence of the measurements. The fundamental diagrams of various flow types are compared and show no apparent difference with respect to the intersecting angle 90° and 180°. This result indicates that head-on conflicts of different types of flow have the same influence on the transport properties of the system, which demonstrates the high self-organization capabilities of pedestrians.

Transition and mixing in axisymmetric jets and vortex rings

NASA Technical Reports Server (NTRS)

Allen, G. A., Jr.; Cantwell, B. J.

1986-01-01

A class of impulsively started, axisymmetric, laminar jets produced by a time dependent joint source of momentum are considered. These jets are different flows, each initially at rest in an unbounded fluid. The study is conducted at three levels of detail. First, a generalized set of analytic creeping flow solutions are derived with a method of flow classification. Second, from this set, three specific creeping flow solutions are studied in detail: the vortex ring, the round jet, and the ramp jet. This study involves derivation of vorticity, stream function, entrainment diagrams, and evolution of time lines through computer animation. From entrainment diagrams, critical points are derived and analyzed. The flow geometry is dictated by the properties and location of critical points which undergo bifurcation and topological transformation (a form of transition) with changing Reynolds number. Transition Reynolds numbers were calculated. A state space trajectory was derived describing the topological behavior of these critical points. This state space derivation yielded three states of motion which are universal for all axisymmetric jets. Third, the axisymmetric round jet is solved numerically using the unsteady laminar Navier Stokes equations. These equations were shown to be self similar for the round jet. Numerical calculations were performed up to a Reynolds number of 30 for a 60x60 point mesh. Animations generated from numerical solution showed each of the three states of motion for the round jet, including the Re = 30 case.

An efficient and general numerical method to compute steady uniform vortices

NASA Astrophysics Data System (ADS)

Luzzatto-Fegiz, Paolo; Williamson, Charles H. K.

2011-07-01

Steady uniform vortices are widely used to represent high Reynolds number flows, yet their efficient computation still presents some challenges. Existing Newton iteration methods become inefficient as the vortices develop fine-scale features; in addition, these methods cannot, in general, find solutions with specified Casimir invariants. On the other hand, available relaxation approaches are computationally inexpensive, but can fail to converge to a solution. In this paper, we overcome these limitations by introducing a new discretization, based on an inverse-velocity map, which radically increases the efficiency of Newton iteration methods. In addition, we introduce a procedure to prescribe Casimirs and remove the degeneracies in the steady vorticity equation, thus ensuring convergence for general vortex configurations. We illustrate our methodology by considering several unbounded flows involving one or two vortices. Our method enables the computation, for the first time, of steady vortices that do not exhibit any geometric symmetry. In addition, we discover that, as the limiting vortex state for each flow is approached, each family of solutions traces a clockwise spiral in a bifurcation plot consisting of a velocity-impulse diagram. By the recently introduced "IVI diagram" stability approach [Phys. Rev. Lett. 104 (2010) 044504], each turn of this spiral is associated with a loss of stability for the steady flows. Such spiral structure is suggested to be a universal feature of steady, uniform-vorticity flows.

Phase diagram for inertial granular flows.

PubMed

DeGiuli, E; McElwaine, J N; Wyart, M

2016-07-01

Flows of hard granular materials depend strongly on the interparticle friction coefficient μ_{p} and on the inertial number I, which characterizes proximity to the jamming transition where flow stops. Guided by numerical simulations, we derive the phase diagram of dense inertial flow of spherical particles, finding three regimes for 10^{-4}≲I≲10^{-1}: frictionless, frictional sliding, and rolling. These are distinguished by the dominant means of energy dissipation, changing from collisional to sliding friction, and back to collisional, as μ_{p} increases from zero at constant I. The three regimes differ in their kinetics and rheology; in particular, the velocity fluctuations and the stress ratio both display nonmonotonic behavior with μ_{p}, corresponding to transitions between the three regimes of flow. We rationalize the phase boundaries between these regimes, show that energy balance yields scaling relations between microscopic properties in each of them, and derive the strain scale at which particles lose memory of their velocity. For the frictional sliding regime most relevant experimentally, we find for I≥10^{-2.5} that the growth of the macroscopic friction μ(I) with I is induced by an increase of collisional dissipation. This implies in that range that μ(I)-μ(0)∼I^{1-2b}, where b≈0.2 is an exponent that characterizes both the dimensionless velocity fluctuations L∼I^{-b} and the density of sliding contacts χ∼I^{b}.

Predicting bed shear stress and its role in sediment dynamics and restoration potential of the Everglades and other vegetated flow systems

USGS Publications Warehouse

Larsen, Laurel G.; Harvey, Judson; Crimaldi, John P.

2009-01-01

Entrainment of sediment by flowing water affects topography, habitat suitability, and nutrient cycling in vegetated floodplains and wetlands, impacting ecosystem evolution and the success of restoration projects. Nonetheless, restoration managers lack simple decision-support tools for predicting shear stresses and sediment redistribution potential in different vegetation communities. Using a field-validated numerical model, we developed state-space diagrams that provide these predictions over a range of water-surface slopes, depths, and associated velocities in Everglades ridge and slough vegetation communities. Diminished bed shear stresses and a consequent decrease in bed sediment redistribution are hypothesized causes of a recent reduction in the topographic and vegetation heterogeneity of this ecosystem. Results confirmed the inability of present-day flows to entrain bed sediment. Further, our diagrams showed bed shear stresses to be highly sensitive to emergent vegetation density and water-surface slope but less sensitive to water depth and periphyton or floating vegetation abundance. These findings suggested that instituting a pulsing flow regime could be the most effective means to restore sediment redistribution to the Everglades. However, pulsing flows will not be sufficient to erode sediment from sloughs with abundant spikerush, unless spikerush density first decreases by natural or managed processes. Our methods provide a novel tool for identifying restoration parameters and performance measures in many types of vegetated aquatic environments where sediment erosion and deposition are involved.

Gas dynamics. Second edition

DOE Office of Scientific and Technical Information (OSTI.GOV)

John, J.E.A.

1984-01-01

The book treats the basic fundamentals of compressible flow and gas dynamics using a wide breadth of topical coverage. It emphasizes the clear, logical development of basic theory and applies theory to real engineering systems. New in this edition is a complete changeover from English units to SI units. New charts for computing flows containing conical shock waves and expanded tables for isentropic flow and normal shocks are featured. The text emphasizes one dimensional and internal flow, and contains: improved illustrations; many new homework problems; examples and problems involving current applications; and new Mollier diagrams for computing real gas effects.

Flow induced crystallisation of penetrable particles

NASA Astrophysics Data System (ADS)

Scacchi, Alberto; Brader, Joseph M.

2018-03-01

For a system of Brownian particles interacting via a soft exponential potential we investigate the interaction between equilibrium crystallisation and spatially varying shear flow. For thermodynamic state points within the liquid part of the phase diagram, but close to the crystallisation phase boundary, we observe that imposing a Poiseuille flow can induce nonequilibrium crystalline ordering in regions of low shear gradient. The physical mechanism responsible for this phenomenon is shear-induced particle migration, which causes particles to drift preferentially towards the center of the flow channel, thus increasing the local density in the channel center. The method employed is classical dynamical density functional theory.

Flow induced crystallisation of penetrable particles.

PubMed

Scacchi, Alberto; Brader, Joseph M

2018-03-07

For a system of Brownian particles interacting via a soft exponential potential we investigate the interaction between equilibrium crystallisation and spatially varying shear flow. For thermodynamic state points within the liquid part of the phase diagram, but close to the crystallisation phase boundary, we observe that imposing a Poiseuille flow can induce nonequilibrium crystalline ordering in regions of low shear gradient. The physical mechanism responsible for this phenomenon is shear-induced particle migration, which causes particles to drift preferentially towards the center of the flow channel, thus increasing the local density in the channel center. The method employed is classical dynamical density functional theory.

Are reports of randomized controlled trials improving over time? A systematic review of 284 articles published in high-impact general and specialized medical journals.

PubMed

To, Matthew J; Jones, Jennifer; Emara, Mohamed; Jadad, Alejandro R

2013-01-01

Inadequate reporting undermines findings of randomized controlled trials (RCTs). This study assessed and compared articles published in high-impact general medical and specialized journals. Reports of RCTs published in high-impact general and specialized medical journals were identified through a search of MEDLINE from January to March of 1995, 2000, 2005, and 2010. Articles that provided original data on adult patients diagnosed with chronic conditions were included in the study. Data on trial characteristics, reporting of allocation concealment, quality score, and the presence of a trial flow diagram were extracted independently by two reviewers, and discrepancies were resolved by consensus or independent adjudication. Descriptive statistics were used for quantitative variables. Comparisons between general medical and specialized journals, and trends over time were performed using Chi-square tests. Reports of 284 trials were analyzed. There was a significantly higher proportion of RCTs published with adequate reporting of allocation concealment (p = 0.003), presentation of a trial flow diagram (p<0.0001) and high quality scores (p = 0.038) over time. Trials published in general medical journals had higher quality scores than those in specialized journals (p = 0.001), reported adequate allocation concealment more often (p = 0.013), and presented a trial flow diagram more often (p<0.001). We found significant improvements in reporting quality of RCTs published in high-impact factor journals over the last fifteen years. These improvements are likely attributed to concerted international efforts to improve reporting quality such as CONSORT. There is still much room for improvement, especially among specialized journals.

A system architecture for a planetary rover

NASA Technical Reports Server (NTRS)

Smith, D. B.; Matijevic, J. R.

1989-01-01

Each planetary mission requires a complex space vehicle which integrates several functions to accomplish the mission and science objectives. A Mars Rover is one of these vehicles, and extends the normal spacecraft functionality with two additional functions: surface mobility and sample acquisition. All functions are assembled into a hierarchical and structured format to understand the complexities of interactions between functions during different mission times. It can graphically show data flow between functions, and most importantly, the necessary control flow to avoid unambiguous results. Diagrams are presented organizing the functions into a structured, block format where each block represents a major function at the system level. As such, there are six blocks representing telecomm, power, thermal, science, mobility and sampling under a supervisory block called Data Management/Executive. Each block is a simple collection of state machines arranged into a hierarchical order very close to the NASREM model for Telerobotics. Each layer within a block represents a level of control for a set of state machines that do the three primary interface functions: command, telemetry, and fault protection. This latter function is expanded to include automatic reactions to the environment as well as internal faults. Lastly, diagrams are presented that trace the system operations involved in moving from site to site after site selection. The diagrams clearly illustrate both the data and control flows. They also illustrate inter-block data transfers and a hierarchical approach to fault protection. This systems architecture can be used to determine functional requirements, interface specifications and be used as a mechanism for grouping subsystems (i.e., collecting groups of machines, or blocks consistent with good and testable implementations).

Experimental consideration of capillary chromatography based on tube radial distribution of ternary mixture carrier solvents under laminar flow conditions.

PubMed

Jinno, Naoya; Hashimoto, Masahiko; Tsukagoshi, Kazuhiko

2011-01-01

A capillary chromatography system has been developed based on the tube radial distribution of the carrier solvents using an open capillary tube and a water-acetonitrile-ethyl acetate mixture carrier solution. This tube radial distribution chromatography (TRDC) system works under laminar flow conditions. In this study, a phase diagram for the ternary mixture carrier solvents of water, acetonitrile, and ethyl acetate was constructed. The phase diagram that included a boundary curve between homogeneous and heterogeneous solutions was considered together with the component ratios of the solvents in the homogeneous carrier solutions required for the TRDC system. It was found that the TRDC system performed well with homogeneous solutions having component ratios of the solvents that were positioned near the homogeneous-heterogeneous solution boundary of the phase diagram. For preparing the carrier solutions of water-hydrophilic/hydrophobic organic solvents for the TRDC system, we used for the first time methanol, ethanol, 1,4-dioxane, and 1-propanol, instead of acetonitrile (hydrophilic organic solvent), as well as chloroform and 1-butanol, instead of ethyl acetate (hydrophobic organic solvent). The homogeneous ternary mixture carrier solutions were prepared near the homogeneous-heterogeneous solution boundary. Analyte mixtures of 2,6-naphthalenedisulfonic acid and 1-naphthol were separated with the TRDC system using these homogeneous ternary mixture carrier solutions. The pressure change in the capillary tube under laminar flow conditions might alter the carrier solution from homogeneous in the batch vessel to heterogeneous, thus affecting the tube radial distribution of the solvents in the capillary tube.

A network thermodynamic two-port element to represent the coupled flow of salt and current. Improved alternative for the equivalent circuit.

PubMed Central

Mikulecky, D C

1979-01-01

A two-port for coupled salt and current flow is created by using the network thermodynamic approach in the same manner as that for coupled solute and volume flow (Mikulecky et al., 1977b; Mikulecky, 1977). This electrochemical two-port has distinct advantages over the equivalent circuit representation and overcomes difficulties pointed out by Finkelstein and Mauro (1963). The electrochemical two-port is used to produce a schematic diagram of the coupled flows through a tissue. The network is superimposable on the tissue morphology and preserves the physical qualities of the flows and forces in each part of an organized structure (e.g., an epithelium). The topological properties are manipulated independently from the constitutive (flow-force) relations. The constitutive relations are chosen from a number of alternatives depending on the detail and rigor desired. With the topology and constitutive parameters specified, the steady-state behavior is simulated with a network simulation program. By using capacitance to represent the filling and depletion of compartments, as well as the traditional electrical capacitances, time-dependent behavior is also simulated. Nonlinear effects arising from the integration of equations describing local behavior (e.g., the Nernst-Planck equations) are dealt with explicitly. The network thermodynamic approach provides a simple, straightforward method for representing a system diagrammatically and then simulating the system's behavior from the diagram with a minimum of mathematical manipulation. PMID:262391

Library Services to University Branch Campuses: The Ohio State Experience

ERIC Educational Resources Information Center

Schmidt, C. James; And Others

1970-01-01

The Ohio State University Main Library acquires and processes books, on a cost-supported contract basis, for each of four regional campus undergraduate libraries. The article describes requirements, rationale, and procedures, and diagrams procedural flow. (Author/NH)

Phase diagram of the triangular-lattice Potts antiferromagnet

DOE PAGES

Jacobsen, Jesper Lykke; Salas, Jesus; Scullard, Christian R.

2017-07-28

Here, we study the phase diagram of the triangular-lattice Q-state Potts model in the realmore » $(Q, v)$ -plane, where $$v={\\rm e}^J-1$$ is the temperature variable. Our first goal is to provide an obviously missing feature of this diagram: the position of the antiferromagnetic critical curve. This curve turns out to possess a bifurcation point with two branches emerging from it, entailing important consequences for the global phase diagram. We have obtained accurate numerical estimates for the position of this curve by combining the transfer-matrix approach for strip graphs with toroidal boundary conditions and the recent method of critical polynomials. The second goal of this work is to study the corresponding $$A_{p-1}$$ RSOS model on the torus, for integer $$p=4, 5, \\ldots, 8$$ . We clarify its relation to the corresponding Potts model, in particular concerning the role of boundary conditions. For certain values of p, we identify several new critical points and regimes for the RSOS model and we initiate the study of the flows between the corresponding field theories.« less

Tug fleet and ground operations schedules and controls. Volume 2: Part 3, appendixes

NASA Technical Reports Server (NTRS)

1975-01-01

A space tug function description data sheet is prepared for each block of the space tug functional flow diagram. A summary of the basic information regarding the activities performed in its respective functional block is provided. The sheets are catalogued by functional flow block numbers with reference blocks at the end. The specific items of information contained in each data sheet are defined.

Heat Flow vs. Cash Flow: A Banking Analogy

NASA Astrophysics Data System (ADS)

Wynn, Charles M., Sr.

1997-04-01

An analogy is drawn between the withdrawal of money from an automated teller machine (ATM) and an exothermic chemical reaction. In the analogy the amount in an individual's account is regarded as the system and the money withdrawn is regarded as part of the surroundings. Diagrams are used to present the analogy. An analogy can be drawn also between a deposit into an account and an endothermic chemical reaction.

High-Order Multioperator Compact Schemes for Numerical Simulation of Unsteady Subsonic Airfoil Flow

NASA Astrophysics Data System (ADS)

Savel'ev, A. D.

2018-02-01

On the basis of high-order schemes, the viscous gas flow over the NACA2212 airfoil is numerically simulated at a free-stream Mach number of 0.3 and Reynolds numbers ranging from 103 to 107. Flow regimes sequentially varying due to variations in the free-stream viscosity are considered. Vortex structures developing on the airfoil surface are investigated, and a physical interpretation of this phenomenon is given.

Effect of nicergoline on cerebral blood flow

PubMed Central

Iliff, L. D.; Boulay, G. H. Du; Marshall, John; Russell, R. W. Ross; Symon, Lindsay

1977-01-01

Cerebral blood flow (CBF) was measured before and after intravenous injection of the cerebral vasodilator nicergoline in 13 patients with cerebrovascular disease. CBF increased in seven. The possibility that the effect of the drug in the remainder may have been masked by a fall of CBF which occurs during sequential measurement of patients at rest is discussed. PMID:925694

Dark energy domination in the Virgocentric flow

NASA Astrophysics Data System (ADS)

Chernin, A. D.; Karachentsev, I. D.; Nasonova, O. G.; Teerikorpi, P.; Valtonen, M. J.; Dolgachev, V. P.; Domozhilova, L. M.; Byrd, G. G.

2010-09-01

Context. The standard ΛCDM cosmological model implies that all celestial bodies are embedded in a perfectly uniform dark energy background, represented by Einstein's cosmological constant, and experience its repulsive antigravity action. Aims: Can dark energy have strong dynamical effects on small cosmic scales as well as globally? Continuing our efforts to clarify this question, we now focus on the Virgo Cluster and the flow of expansion around it. Methods: We interpret the Hubble diagram from a new database of velocities and distances of galaxies in the cluster and its environment, using a nonlinear analytical model, which incorporates the antigravity force in terms of Newtonian mechanics. The key parameter is the zero-gravity radius, the distance at which gravity and antigravity are in balance. Results: 1. The interplay between the gravity of the cluster and the antigravity of the dark energy background determines the kinematical structure of the system and controls its evolution. 2. The gravity dominates the quasi-stationary bound cluster, while the antigravity controls the Virgocentric flow, bringing order and regularity to the flow, which reaches linearity and the global Hubble rate at distances ⪆15 Mpc. 3. The cluster and the flow form a system similar to the Local Group and its outflow. In the velocity-distance diagram, the cluster-flow structure reproduces the group-flow structure with a scaling factor of about 10; the zero-gravity radius for the cluster system is also 10 times larger. Conclusions: The phase and dynamical similarity of the systems on the scales of 1-30 Mpc suggests that a two-component pattern may be universal for groups and clusters: a quasi-stationary bound central component and an expanding outflow around it, caused by the nonlinear gravity-antigravity interplay with the dark energy dominating in the flow component.

18 CFR 157.208 - Construction, acquisition, operation, replacement, and miscellaneous rearrangement of facilities.

Code of Federal Regulations, 2013 CFR

2013-04-01

... applicant's existing facilities; (5) A flow diagram or comparative study showing daily design capacity... designed to meet the goal of limiting the perceived noise at NSAs to an Ldn of 55 dBA or what mitigation...

18 CFR 157.208 - Construction, acquisition, operation, replacement, and miscellaneous rearrangement of facilities.

Code of Federal Regulations, 2012 CFR

2012-04-01

... applicant's existing facilities; (5) A flow diagram or comparative study showing daily design capacity... designed to meet the goal of limiting the perceived noise at NSAs to an Ldn of 55 dBA or what mitigation...

18 CFR 157.208 - Construction, acquisition, operation, replacement, and miscellaneous rearrangement of facilities.

Code of Federal Regulations, 2011 CFR

2011-04-01

... applicant's existing facilities; (5) A flow diagram or comparative study showing daily design capacity... designed to meet the goal of limiting the perceived noise at NSAs to an Ldn of 55 dBA or what mitigation...

18 CFR 157.208 - Construction, acquisition, operation, replacement, and miscellaneous rearrangement of facilities.

Code of Federal Regulations, 2010 CFR

2010-04-01

... applicant's existing facilities; (5) A flow diagram or comparative study showing daily design capacity... designed to meet the goal of limiting the perceived noise at NSAs to an Ldn of 55 dBA or what mitigation...

18 CFR 157.208 - Construction, acquisition, operation, replacement, and miscellaneous rearrangement of facilities.

Code of Federal Regulations, 2014 CFR

2014-04-01

... applicant's existing facilities; (5) A flow diagram or comparative study showing daily design capacity... designed to meet the goal of limiting the perceived noise at NSAs to an Ldn of 55 dBA or what mitigation...

The Endocrine Machinery.

ERIC Educational Resources Information Center

Fillman, David

1987-01-01

Promotes a reductionist approach to teaching about the endocrine system in high school biology and anatomy courses. Encourages the study of how hormones travel to the cells and affect them. Provides suggestions for activities and discussion questions, along with sample diagrams and flow charts. (TW)

103. Photocopied 1983, from original drawing (DP49213), Picatinny Arsenal, NOVEMBER ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

103. Photocopied 1983, from original drawing (DP-49213), Picatinny Arsenal, NOVEMBER 23, 1945. ROLLED POWDER AREA FINISHING PLANT: FLOW DIAGRAM.' - Picatinny Arsenal, 500 Area, Powder Factory & Power House, State Route 15 near I-80, Dover, Morris County, NJ

Two MIS Analysis Methods: An Experimental Comparison.

ERIC Educational Resources Information Center

Wang, Shouhong

1996-01-01

In China, 24 undergraduate business students applied data flow diagrams (DFD) to a mini-case, and 20 used object-oriented analysis (OOA). DFD seemed easier to learn, but after training, those using the OOA method for systems analysis made fewer errors. (SK)

Evaluability Assessment: A Retrospective Illustration and Review.

ERIC Educational Resources Information Center

Smith, Nick L.

1981-01-01

Rutman's view of evaluability assessment is reviewed, evaluation planning activities are illustrated via flow diagram for a large educational evaluation designed to increase citizen participation in local school activities, and some of the limitations of Rutman's evaluability procedures are outlined. (RL)

Individualizing Psychomotor Activities for the Handicapped.

ERIC Educational Resources Information Center

Shemick, John M.

1978-01-01

Public Law 94-142 requires that handicapped students have individual education plans containing goals or objectives, description of placement and services, and evaluation specifications. The Fleishman Binary Decision Flow Diagram provides teachers with technique for analyzing program activities for ability requirements. (CSS)

IGS Data Flow

NASA Technical Reports Server (NTRS)

Noll, Carey

2006-01-01

The IGS analysis centers and user community in general need to be assured that the data centers archive a consistent set of files. Changes to the archives can occur because of the re-publishing of data, the transmission of historic data, and the resulting re-distribution (or lack thereof) of these data from data center to data center. To ensure the quality of the archives, a defined data flow and method of archive population needs to be established. This poster will diagram and review the current IGS data flow, discuss problems that have occurred, and provide recommendations for improvement.

Object-oriented analysis and design of a health care management information system.

PubMed

Krol, M; Reich, D L

1999-04-01

We have created a prototype for a universal object-oriented model of a health care system compatible with the object-oriented approach used in version 3.0 of the HL7 standard for communication messages. A set of three models has been developed: (1) the Object Model describes the hierarchical structure of objects in a system--their identity, relationships, attributes, and operations; (2) the Dynamic Model represents the sequence of operations in time as a collection of state diagrams for object classes in the system; and (3) functional Diagram represents the transformation of data within a system by means of data flow diagrams. Within these models, we have defined major object classes of health care participants and their subclasses, associations, attributes and operators, states, and behavioral scenarios. We have also defined the major processes and subprocesses. The top-down design approach allows use, reuse, and cloning of standard components.

The software architecture of climate models: a graphical comparison of CMIP5 and EMICAR5 configurations

NASA Astrophysics Data System (ADS)

Alexander, K.; Easterbrook, S. M.

2015-01-01

We analyse the source code of eight coupled climate models, selected from those that participated in the CMIP5 (Taylor et al., 2012) or EMICAR5 (Eby et al., 2013; Zickfeld et al., 2013) intercomparison projects. For each model, we sort the preprocessed code into components and subcomponents based on dependency structure. We then create software architecture diagrams which show the relative sizes of these components/subcomponents and the flow of data between them. The diagrams also illustrate several major classes of climate model design; the distribution of complexity between components, which depends on historical development paths as well as the conscious goals of each institution; and the sharing of components between different modelling groups. These diagrams offer insights into the similarities and differences between models, and have the potential to be useful tools for communication between scientists, scientific institutions, and the public.

The software architecture of climate models: a graphical comparison of CMIP5 and EMICAR5 configurations

NASA Astrophysics Data System (ADS)

Alexander, K.; Easterbrook, S. M.

2015-04-01

We analyze the source code of eight coupled climate models, selected from those that participated in the CMIP5 (Taylor et al., 2012) or EMICAR5 (Eby et al., 2013; Zickfeld et al., 2013) intercomparison projects. For each model, we sort the preprocessed code into components and subcomponents based on dependency structure. We then create software architecture diagrams that show the relative sizes of these components/subcomponents and the flow of data between them. The diagrams also illustrate several major classes of climate model design; the distribution of complexity between components, which depends on historical development paths as well as the conscious goals of each institution; and the sharing of components between different modeling groups. These diagrams offer insights into the similarities and differences in structure between climate models, and have the potential to be useful tools for communication between scientists, scientific institutions, and the public.

What does it mean to be pseudo single domain? Demystifying the PSD state

NASA Astrophysics Data System (ADS)

Lascu, I.; Harrison, R. J.; Einsle, J. F.; Ball, M.

2016-12-01

Until recently, non-interacting stable single domain grains were thought to be the sole reliable paleomagnetic recorders. However most natural samples contain so-called "non-ideal" paleomagnetic recorders, which are either interacting single domain particles, or magnetic grains larger than single domain grains, but smaller than proper multi domain grains, which are poor paleomagnetic recorders. The grain size range for these recorders, which for magnetite comprises grains from 100 nm to a few μm in size, is known as the pseudo single domain (PSD) state. Natural samples containing abundant PSD grains have been shown time and again to reliably record thermomagnetic remanent magnetizations that are stable over billions of years. Here we attempt to shed new light on the PSD state by investigating obsidian varieties found at Glass Butte, Oregon, which present the opportunity to study simple cases of magnetic grains encapsulated in volcanic glass. We do this by combining rock magnetism, scanning electron microscopy (SEM) nanotomography, and finite-element micromagnetic modeling. Using rock magnetism we have identified PSD signatures in these samples via their fingerprint in first-order reversal curve (FORC) diagrams. Tomographic reconstructions obtained by stacking SEM images acquired via sequential milling through sample volumes of a few tens of cubic μm reveal the presence of abundant grains that span the PSD grain size interval. These grains have a variety of shapes, from simple ellipsoidal particles, to more complex morphologies attained through the coalescence of neighboring grains during crystallization, to intricate "rolling snowball" morphologies in larger grains that contain appendices formed as a result of particle growth in a dynamic environment as the flowing lava cooled. Micromagnetic modeling of the simplest morphologies reveals that these grains are in single vortex states, with the remanence controlled by irregularities in grain morphology. Coalesced grains present extreme cases of shape anisotropy, which will control the remanence. The remanence of the largest grains is controlled by the collection of PSD states from areas of the grain with pronounced shape anisotropy. Finally, micromagnetic modeling of realistic grain shapes allows the understanding of PSD signatures in FORC diagrams.

Diagramming Scientific Papers - A New Idea for Understanding/Teaching/Sharing Science

NASA Astrophysics Data System (ADS)

Saltus, R. W.; Fedi, M.

2014-12-01

How do we best communicate scientific results? As the number of scientists and scientific papers steadily increases, one of the greatest challenges is effective and efficient sharing of science. The official repository of scientific knowledge is the peer-reviewed journal archive. However, this primary knowledge can be difficult to access and understand by anyone but a relevant specialist. We propose some new ideas for diagramming the content and significance of scientific papers using a simple and intuitive graphical approach. We propose a visual mapping that highlights four fundamental aspects of most scientific papers: Data, Methods/Models, Results/Ideas, and Implications/Importance. Each of these aspects is illustrated within boxed fields which contain one or more labeled elements positioned to reflect novelty (aka originality) and impact relative to the vertical and horizontal axes. The relative position of the boxed fields themselves indicates the relative significance of data, methods, ideas, or implications to the paper. Optional lines between boxed elements indicate the flow and dependence of data/methods/ideas within the paper. As with any graphical depiction, you need to see it to best appreciate it -- this written abstract is only meant as an introduction to the idea.We anticipate that diagramming may prove useful in both communication of scientific ideas among scientists as well as in education and outreach. For example, professors could assign diagramming of papers as a way to help students organize their thoughts about the structure and impact of scientific articles. Students could compare and defend their diagrams as a way to facilitate discussion/debate. Authors could diagram their own work as a way to efficiently summarize the importance and significance of their work. We also imagine that (in the future) automatic diagramming might be used to help summarize or facilitate the discovery of archived work.

Crushed cement concrete substitution for construction aggregates; a materials flow analysis

USGS Publications Warehouse

Kelly, Thomas

1998-01-01

An analysis of the substitution of crushed cement concrete for natural construction aggregates is performed by using a materials flow diagram that tracks all material flows into and out of the cement concrete portion of the products made with cement concrete: highways, roads, and buildings. Crushed cement concrete is only one of the materials flowing into these products, and the amount of crushed cement concrete substituted influences the amount of other materials in the flow. Factors such as availability and transportation costs, as well as physical properties, that can affect stability and finishability, influence whether crushed cement concrete or construction aggregates should be used or predominate for a particular end use.

Finite elements for the calculation of turbulent flows in three-dimensional complex geometries

NASA Astrophysics Data System (ADS)

Ruprecht, A.

A finite element program for the calculation of incompressible turbulent flows is presented. In order to reduce the required storage an iterative algorithm is used which solves the necessary equations sequentially. The state of turbulence is defined by the k-epsilon model. In addition to the standard k-epsilon model, the modification of Bardina et al., taking into account the rotation of the mean flow, is investigated. With this program, the flow in the draft tube of a Kaplan turbine is examined. Calculations are carried out for swirling and nonswirling entrance flow. The results are compared with measurements.

Improved numerical methods for turbulent viscous flows aerothermal modeling program, phase 2

NASA Technical Reports Server (NTRS)

Karki, K. C.; Patankar, S. V.; Runchal, A. K.; Mongia, H. C.

1988-01-01

The details of a study to develop accurate and efficient numerical schemes to predict complex flows are described. In this program, several discretization schemes were evaluated using simple test cases. This assessment led to the selection of three schemes for an in-depth evaluation based on two-dimensional flows. The scheme with the superior overall performance was incorporated in a computer program for three-dimensional flows. To improve the computational efficiency, the selected discretization scheme was combined with a direct solution approach in which the fluid flow equations are solved simultaneously rather than sequentially.

Some Effects of Compressibility on the Flow Through Fans and Turbines

DTIC Science & Technology

1945-08-01

conditions, or the velocity diagram, for the cascade of airfoils representing a fan or a turbine - blade arrangement (fig. 1). The conservation laws...Compressibility on the Flow Through Fans and Turbines AUTHOR(S); Perl. W.j Epstein, H.T. ORIGINATING AGENCY: Aircraft Engine Research Lab., Cleveland, O... turbine blading . It appears, however, that use of a suitable polytropic exponent n?^7 allows direct application in many cases.) Substitution of

Unsteady Specific Work and Isentropic Efficiency of a Radial Turbine Driven by Pulsed Detonations

DTIC Science & Technology

2012-06-14

iv AFIT/DS/ENY/12-25 Abstract There has been longstanding government and industry interest in pressure-gain combustion for use in Brayton cycle...10 III.A. Unsteady Flow in Conventional Brayton Cycle Turbines ........................10 III.B. Unsteady Flow in Pulsed Detonation Driven...Szpynda and Nalim 2007) 114 Figure 69. Heiser and Pratt comparison of ideal PDE, Humphrey, and Brayton cycles on a temperature-entropy diagram (Heiser

An Introduction to an International Logistics Language.

DTIC Science & Technology

1982-09-01

cause difficulties for beginners as well as the professional in Systems and Logistics. 3. The author uses terms, acronyms, and abbreviations that are...guarantee flow guide flowchart fly -H focal fold had follow half Follow-on Support halfway follow-up handbook for handle force hang forecast hanger...surface flow (n)(v) - the direction of movement; to move in a con- tinuous speed flowchart (n) - a diagram which shows step by step procedures or

High Level Impulse Sounds and Human Hearing: Standards, Physiology, Quantification

DTIC Science & Technology

2012-05-01

a result of this change the piston-like movements of the stapes are replaced by a tilting action, which is much less effective in pushing cochlear ...Above this threshold, high noise levels result in a turbulent flow of air through the nonlinear element of the protector, effectively dissipating the...electrical diagrams of earplug and earmuff models (Kalb, 2011). In the model shown, the energy flow through the HPD propagates along three parallel

Presentation of the acoustic and aerodynamic results of the Aladin 2 concept qualification testing

NASA Technical Reports Server (NTRS)

Collard, M.; Doyotte, C.; Sagner, M.

1985-01-01

Wind tunnel tests were conducted of a scale model of the Aladin 2 aircraft. The propulsion system configuration is described and the air flow caused by jet ejection is analyzed. Three dimensional flow studies in the vicinity of the engine installation were made. Diagrams of the leading and trailing edge flaps are provided. Graphs are developed to show the aerodynamic performance under conditions of various airspeed and flap deflection.

Fuel quality/processing study. Volume 3: Fuel upgrading studies

NASA Technical Reports Server (NTRS)

Jones, G. E., Jr.; Bruggink, P.; Sinnett, C.

1981-01-01

The methods used to calculate the refinery selling prices for the turbine fuels of low quality are described. Detailed descriptions and economics of the upgrading schemes are included. These descriptions include flow diagrams showing the interconnection between processes and the stream flows involved. Each scheme is in a complete, integrated, stand alone facility. Except for the purchase of electricity and water, each scheme provides its own fuel and manufactures, when appropriate, its own hydrogen.

Enhancement of wall jet transport properties

DOEpatents

Claunch, Scott D.; Farrington, Robert B.

1997-01-01

By enhancing the natural instabilities in the boundary layer and in the free shear layer of a wall jet, the boundary is minimized thereby increasing the transport of heat and mass. Enhancing the natural instabilities is accomplished by pulsing the flow of air that creates the wall jet. Such pulsing of the flow of air can be accomplished by sequentially occluding and opening a duct that confines and directs the flow of air, such as by rotating a disk on an axis transverse to the flow of air in the duct.

Enhancement of wall jet transport properties

DOEpatents

Claunch, S.D.; Farrington, R.B.

1997-02-04

By enhancing the natural instabilities in the boundary layer and in the free shear layer of a wall jet, the boundary is minimized thereby increasing the transport of heat and mass. Enhancing the natural instabilities is accomplished by pulsing the flow of air that creates the wall jet. Such pulsing of the flow of air can be accomplished by sequentially occluding and opening a duct that confines and directs the flow of air, such as by rotating a disk on an axis transverse to the flow of air in the duct. 17 figs.

Functionalized Anodic Aluminum Oxide Membrane–Electrode System for Enzyme Immobilization

PubMed Central

2015-01-01

A nanoporous membrane system with directed flow carrying reagents to sequentially attached enzymes to mimic nature’s enzyme complex system was demonstrated. Genetically modified glycosylation enzyme, OleD Loki variant, was immobilized onto nanometer-scale electrodes at the pore entrances/exits of anodic aluminum oxide membranes through His6-tag affinity binding. The enzyme activity was assessed in two reactions—a one-step “reverse” sugar nucleotide formation reaction (UDP-Glc) and a two-step sequential sugar nucleotide formation and sugar nucleotide-based glycosylation reaction. For the one-step reaction, enzyme specific activity of 6–20 min–1 on membrane supports was seen to be comparable to solution enzyme specific activity of 10 min–1. UDP-Glc production efficiencies as high as 98% were observed at a flow rate of 0.5 mL/min, at which the substrate residence time over the electrode length down pore entrances was matched to the enzyme activity rate. This flow geometry also prevented an unwanted secondary product hydrolysis reaction, as observed in the test homogeneous solution. Enzyme utilization increased by a factor of 280 compared to test homogeneous conditions due to the continuous flow of fresh substrate over the enzyme. To mimic enzyme complex systems, a two-step sequential reaction using OleD Loki enzyme was performed at membrane pore entrances then exits. After UDP-Glc formation at the entrance electrode, aglycon 4-methylumbelliferone was supplied at the exit face of the reactor, affording overall 80% glycosylation efficiency. The membrane platform showed the ability to be regenerated with purified enzyme as well as directly from expression crude, thus demonstrating a single-step immobilization and purification process. PMID:25025628

7 CFR 42.123 - Flow diagram for skip lot sampling and inspection.

Code of Federal Regulations, 2010 CFR

2010-01-01

....123 Section 42.123 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing Practices), DEPARTMENT OF AGRICULTURE COMMODITY STANDARDS AND STANDARD CONTAINER REGULATIONS STANDARDS FOR CONDITION OF FOOD CONTAINERS Skip Lot Sampling and Inspection...

An Economic Comparison of Passively Conditioned Underground Houses.

DTIC Science & Technology

1981-05-01

15 Heat Transfer ........ ..................... ... 34 Energy Balance and Human Thermal Comfort . ...... ... 41 Conclusion...114 29. Thermal Comfort --Passive Underground House ... ........... .. 117 30. Stable Soil Temperature Depths...121 31. Thermal Comfort --Deep Earth Underground House .. ......... .. 124 32. Life Cycle Cash Flow Diagram--Base Underground House

Map Your Way to a Better Lab.

ERIC Educational Resources Information Center

Roth, Wolff-Michael

1990-01-01

The use of concept maps, Vee diagrams, flow charts, and productive questions to increase student understanding of laboratory exercises and to improve student attitudes toward lab classes is discussed. Examples of each are provided. Student responses to these teaching methods are described. (CW)

Stack Gas Scrubber Makes the Grade

ERIC Educational Resources Information Center

Chemical and Engineering News, 1975

1975-01-01

Describes a year long test of successful sulfur dioxide removal from stack gas with a calcium oxide slurry. Sludge disposal problems are discussed. Cost is estimated at 0.6 mill per kwh not including sludge removal. A flow diagram and equations are included. (GH)

First year medical students' learning style preferences and their correlation with performance in different subjects within the medical course.

PubMed

Hernández-Torrano, Daniel; Ali, Syed; Chan, Chee-Kai

2017-08-08

Students commencing their medical training arrive with different educational backgrounds and a diverse range of learning experiences. Consequently, students would have developed preferred approaches to acquiring and processing information or learning style preferences. Understanding first-year students' learning style preferences is important to success in learning. However, little is understood about how learning styles impact learning and performance across different subjects within the medical curriculum. Greater understanding of the relationship between students' learning style preferences and academic performance in specific medical subjects would be valuable. This cross-sectional study examined the learning style preferences of first-year medical students and how they differ across gender. This research also analyzed the effect of learning styles on academic performance across different subjects within a medical education program in a Central Asian university. A total of 52 students (57.7% females) from two batches of first-year medical school completed the Index of Learning Styles Questionnaire, which measures four dimensions of learning styles: sensing-intuitive; visual-verbal; active-reflective; sequential-global. First-year medical students reported preferences for visual (80.8%) and sequential (60.5%) learning styles, suggesting that these students preferred to learn through demonstrations and diagrams and in a linear and sequential way. Our results indicate that male medical students have higher preference for visual learning style over verbal, while females seemed to have a higher preference for sequential learning style over global. Significant associations were found between sensing-intuitive learning styles and performance in Genetics [β = -0.46, B = -0.44, p < 0.01] and Anatomy [β = -0.41, B = -0.61, p < 0.05] and between sequential-global styles and performance in Genetics [β = 0.36, B = 0.43, p < 0.05]. More specifically, sensing learners were more likely to perform better than intuitive learners in the two subjects and global learners were more likely to perform better than sequential learners in Genetics. This knowledge will be helpful to individual students to improve their performance in these subjects by adopting new sensing learning techniques. Instructors can also benefit by modifying and adapting more appropriate teaching approaches in these subjects. Future studies to validate this observation will be valuable.

Instability patterns in a miscible core annular flow

NASA Astrophysics Data System (ADS)

D'Olce, Marguerite; Martin, Jerome; Rakotomalala, Nicole; Salin, Dominique; Talon, Laurent

2006-11-01

Laboratoire FAST, batiment 502, campus universitaire, 91405 Orsay Cedex (France). Experiments are performed with two miscible fluids of equal density but different viscosities. The fluids are injected co-currently and concentrically into a cylindrical pipe. The so-obtained base state is an axisymmetric parallel flow, for which the ratio of the flow rates of the two fluids monitors the relative amount (and so the radius) of the fluids. Depending on this relative amount and on the total flow rate of the fluids, unstable axisymmetric patterns such as mushrooms and pearls are observed. We delineate the diagram of occurrence of the two patterns and characterize the instabilities.

Flow-driven pattern formation in the calcium-oxalate system.

PubMed

Bohner, Bíborka; Endrődi, Balázs; Horváth, Dezső; Tóth, Ágota

2016-04-28

The precipitation reaction of calcium oxalate is studied experimentally in the presence of spatial gradients by controlled flow of calcium into oxalate solution. The density difference between the reactants leads to strong convection in the form of a gravity current that drives the spatiotemporal pattern formation. The phase diagram of the system is constructed, the evolving precipitate patterns are analyzed and quantitatively characterized by their diameters and the average height of the gravity flow. The compact structures of calcium oxalate monohydrate produced at low flow rates are replaced by the thermodynamically unstable calcium oxalate dihydrate favored in the presence of a strong gravity current.

Exploring Learners' Sequential Behavioral Patterns, Flow Experience, and Learning Performance in an Anti-Phishing Educational Game

ERIC Educational Resources Information Center

Sun, Jerry Chih-Yuan; Kuo, Cian-Yu; Hou, Huei-Tse; Lin, Yu-Yan

2017-01-01

The purposes of this study were to provide a game-based anti-phishing lesson to 110 elementary school students in Taiwan, explore their learning behavioral patterns, and investigate the effects of the flow states on their learning behavioral patterns and learning achievement. The study recorded behaviour logs, and applied a pre- and post-test on…

Polymeric microchip for the simultaneous determination of anions and cations by hydrodynamic injection using a dual-channel sequential injection microchip electrophoresis system.

PubMed

Gaudry, Adam J; Nai, Yi Heng; Guijt, Rosanne M; Breadmore, Michael C

2014-04-01

A dual-channel sequential injection microchip capillary electrophoresis system with pressure-driven injection is demonstrated for simultaneous separations of anions and cations from a single sample. The poly(methyl methacrylate) (PMMA) microchips feature integral in-plane contactless conductivity detection electrodes. A novel, hydrodynamic "split-injection" method utilizes background electrolyte (BGE) sheathing to gate the sample flows, while control over the injection volume is achieved by balancing hydrodynamic resistances using external hydrodynamic resistors. Injection is realized by a unique flow-through interface, allowing for automated, continuous sampling for sequential injection analysis by microchip electrophoresis. The developed system was very robust, with individual microchips used for up to 2000 analyses with lifetimes limited by irreversible blockages of the microchannels. The unique dual-channel geometry was demonstrated by the simultaneous separation of three cations and three anions in individual microchannels in under 40 s with limits of detection (LODs) ranging from 1.5 to 24 μM. From a series of 100 sequential injections the %RSDs were determined for every fifth run, resulting in %RSDs for migration times that ranged from 0.3 to 0.7 (n = 20) and 2.3 to 4.5 for peak area (n = 20). This system offers low LODs and a high degree of reproducibility and robustness while the hydrodynamic injection eliminates electrokinetic bias during injection, making it attractive for a wide range of rapid, sensitive, and quantitative online analytical applications.

Understanding widely scattered traffic flows, the capacity drop, and platoons as effects of variance-driven time gaps

NASA Astrophysics Data System (ADS)

Treiber, Martin; Kesting, Arne; Helbing, Dirk

2006-07-01

We investigate the adaptation of the time headways in car-following models as a function of the local velocity variance, which is a measure of the inhomogeneity of traffic flow. We apply this mechanism to several car-following models and simulate traffic breakdowns in open systems with an on-ramp as bottleneck and in a closed ring road. Single-vehicle data and one-minute aggregated data generated by several virtual detectors show a semiquantitative agreement with microscopic and flow-density data from the Dutch freeway A9. This includes the observed distributions of the net time headways for free and congested traffic, the velocity variance as a function of density, and the fundamental diagram. The modal value of the time headway distribution is shifted by a factor of about 2 under congested conditions. Macroscopically, this corresponds to the capacity drop at the transition from free to congested traffic. The simulated fundamental diagram shows free, synchronized, and jammed traffic, and a wide scattering in the congested traffic regime. We explain this by a self-organized variance-driven process that leads to the spontaneous formation and decay of long-lived platoons even for a deterministic dynamics on a single lane.

Renormalization group analysis of dipolar Heisenberg model on square lattice

NASA Astrophysics Data System (ADS)

Keleş, Ahmet; Zhao, Erhai

2018-06-01

We present a detailed functional renormalization group analysis of spin-1/2 dipolar Heisenberg model on square lattice. This model is similar to the well-known J1-J2 model and describes the pseudospin degrees of freedom of polar molecules confined in deep optical lattice with long-range anisotropic dipole-dipole interactions. Previous study of this model based on tensor network ansatz indicates a paramagnetic ground state for certain dipole tilting angles which can be tuned in experiments to control the exchange couplings. The tensor ansatz formulated on a small cluster unit cell is inadequate to describe the spiral order, and therefore the phase diagram at high azimuthal tilting angles remains undetermined. Here, we obtain the full phase diagram of the model from numerical pseudofermion functional renormalization group calculations. We show that an extended quantum paramagnetic phase is realized between the Néel and stripe/spiral phases. In this region, the spin susceptibility flows smoothly down to the lowest numerical renormalization group scales with no sign of divergence or breakdown of the flow, in sharp contrast to the flow towards the long-range-ordered phases. Our results provide further evidence that the dipolar Heisenberg model is a fertile ground for quantum spin liquids.

OFFl Models: Novel Schema for Dynamical Modeling of Biological Systems

PubMed Central

2016-01-01

Flow diagrams are a common tool used to help build and interpret models of dynamical systems, often in biological contexts such as consumer-resource models and similar compartmental models. Typically, their usage is intuitive and informal. Here, we present a formalized version of flow diagrams as a kind of weighted directed graph which follow a strict grammar, which translate into a system of ordinary differential equations (ODEs) by a single unambiguous rule, and which have an equivalent representation as a relational database. (We abbreviate this schema of “ODEs and formalized flow diagrams” as OFFL.) Drawing a diagram within this strict grammar encourages a mental discipline on the part of the modeler in which all dynamical processes of a system are thought of as interactions between dynamical species that draw parcels from one or more source species and deposit them into target species according to a set of transformation rules. From these rules, the net rate of change for each species can be derived. The modeling schema can therefore be understood as both an epistemic and practical heuristic for modeling, serving both as an organizational framework for the model building process and as a mechanism for deriving ODEs. All steps of the schema beyond the initial scientific (intuitive, creative) abstraction of natural observations into model variables are algorithmic and easily carried out by a computer, thus enabling the future development of a dedicated software implementation. Such tools would empower the modeler to consider significantly more complex models than practical limitations might have otherwise proscribed, since the modeling framework itself manages that complexity on the modeler’s behalf. In this report, we describe the chief motivations for OFFL, carefully outline its implementation, and utilize a range of classic examples from ecology and epidemiology to showcase its features. PMID:27270918

Efficient flow injection and sequential injection methods for spectrophotometric determination of oxybenzone in sunscreens based on reaction with Ni(II).

PubMed

Chisvert, A; Salvador, A; Pascual-Martí, M C; March, J G

2001-04-01

Spectrophotometric determination of a widely used UV-filter, such as oxybenzone, is proposed. The method is based on the complexation reaction between oxybenzone and Ni(II) in ammoniacal medium. The stoichiometry of the reaction, established by the Job method, was 1:1. Reaction conditions were studied and the experimental parameters were optimized, for both flow injection (FI) and sequential injection (SI) determinations, with comparative purposes. Sunscreen formulations containing oxybenzone were analyzed by the proposed methods and results compared with those obtained by HPLC. Data show that both FI and SI procedures provide accurate and precise results. The ruggedness, sensitivity and LOD are adequate to the analysis requirements. The sample frequency obtained by FI is three-fold higher than that of SI analysis. SI is less reagent-consuming than FI.

Modelling, fabrication and characterization of a polymeric micromixer based on sequential segmentation.

PubMed

Nguyen, Nam-Trung; Huang, Xiaoyang

2006-06-01

Effective and fast mixing is important for many microfluidic applications. In many cases, mixing is limited by molecular diffusion due to constrains of the laminar flow in the microscale regime. According to scaling law, decreasing the mixing path can shorten the mixing time and enhance mixing quality. One of the techniques for reducing mixing path is sequential segmentation. This technique divides solvent and solute into segments in axial direction. The so-called Taylor-Aris dispersion can improve axial transport by three orders of magnitudes. The mixing path can be controlled by the switching frequency and the mean velocity of the flow. Mixing ratio can be controlled by pulse width modulation of the switching signal. This paper first presents a simple time-dependent one-dimensional analytical model for sequential segmentation. The model considers an arbitrary mixing ratio between solute and solvent as well as the axial Taylor-Aris dispersion. Next, a micromixer was designed and fabricated based on polymeric micromachining. The micromixer was formed by laminating four polymer layers. The layers are micro machined by a CO(2) laser. Switching of the fluid flows was realized by two piezoelectric valves. Mixing experiments were evaluated optically. The concentration profile along the mixing channel agrees qualitatively well with the analytical model. Furthermore, mixing results at different switching frequencies were investigated. Due to the dynamic behavior of the valves and the fluidic system, mixing quality decreases with increasing switching frequency.

Characterization and Prediction of Flow Behavior in High-Manganese Twinning Induced Plasticity Steels: Part II. Jerky Flow and Instantaneous Strain Rate

NASA Astrophysics Data System (ADS)

Saeed-Akbari, A.; Mishra, A. K.; Mayer, J.; Bleck, W.

2012-05-01

The jerky and smooth flow curves in high-manganese twinning induced plasticity (TWIP) steels were investigated by comparing Fe-Mn-C and Fe-Mn-Al-C systems. The pronounced serrations on the flow curves of Fe-Mn-C TWIP steel, produced during tensile testing at 300 K (27 °C) and 373 K (100 °C), were shown to be the result of localized high-temperature Portevin Le-Chatelier (PLC) bands moving across the gage length throughout the deformation. The speed of the PLC bands and their temperature effects were found to be strongly dependent on the applied strain rate, which was controlled by adjusting the cross-head speed of the tensile testing machine. The localized temperature-dependent stacking fault energy (SFE) variations resulting from the PLC effect and adiabatic heating were analyzed and compared for both slow and fast deformation rates. The instabilities in the measured logarithmic strain values caused by jerky flow could cause the local strain rate to deviate systematically from the targeted (applied) strain rate. These instabilities are better observed by calculating the instantaneous strain rate (ISR) values for each instant of deformation along the entire gage length. Finally, a new type of diagram was developed by plotting the true stress against the ISR values. From the diagram, the onset of different mechanisms, such as deformation twinning, nonpronounced, and pronounced serrations, could be marked precisely.

Modeling mechanical restriction differences between car and heavy truck in two-lane cellular automata traffic flow model

NASA Astrophysics Data System (ADS)

Li, Xin; Li, Xingang; Xiao, Yao; Jia, Bin

2016-06-01

Real traffic is heterogeneous with car and truck. Due to mechanical restrictions, the car and the truck have different limited deceleration capabilities, which are important factors in safety driving. This paper extends the single lane safety driving (SD) model with limited deceleration capability to two-lane SD model, in which car-truck heterogeneous traffic is considered. A car has a larger limited deceleration capability while a heavy truck has a smaller limited deceleration capability as a result of loaded goods. Then the safety driving conditions are different as the types of the following and the leading vehicles vary. In order to eliminate the well-known plug in heterogeneous two-lane traffic, it is assumed that heavy truck has active deceleration behavior when the heavy truck perceives the forming plug. The lane-changing decisions are also determined by the safety driving conditions. The fundamental diagram, spatiotemporal diagram, and lane-changing frequency were investigated to show the effect of mechanical restriction on heterogeneous traffic flow. It was shown that there would be still three traffic phases in heterogeneous traffic condition; the active deceleration of the heavy truck could well eliminate the plug; the lane-changing frequency was low in synchronized flow; the flow and velocity would decrease as the proportion of heavy truck grows or the limited deceleration capability of heavy truck drops; and the flow could be improved with lane control measures.

Rapid, high-temperature, field test method for evaluation of geothermal calcium carbonate scale inhibitors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Asperger, R.G.

1986-09-01

A new test method is described that allows the rapid field testing of calcium carbonate scale inhibitors at 500/sup 0/F (260/sup 0/C). The method evolved from use of a full-flow test loop on a well with a mass flow rate of about 1 x 10/sup 6/ lbm/hr (126 kg/s). It is a simple, effective way to evaluate the effectiveness of inhibitors under field conditions. Five commercial formulations were chosen for field evaluation on the basis of nonflowing, laboratory screening tests at 500/sup 0/F (260/sup 0/C). Four of these formulations from different suppliers controlled calcium carbonate scale deposition as measured bymore » the test method. Two of these could dislodge recently deposited scale that had not age-hardened. Performance-profile diagrams, which were measured for these four effective inhibitors, show the concentration interrelationship between brine calcium and inhibitor concentrations at which the formulations will and will not stop scale formation in the test apparatus. With these diagrams, one formulation was chosen for testing on the full-flow brine line. The composition was tested for 6 weeks and showed a dramatic decrease in the scaling occurring at the flow-control valve. This scaling was about to force a shutdown of a major, long-term flow test being done for reservoir economic evaluations. The inhibitor stopped the scaling, and the test was performed without interruption.« less

Bedside assistance in freehand ultrasonic diagnosis by real-time visual feedback of 3D scatter diagram of pulsatile tissue-motion

NASA Astrophysics Data System (ADS)

Fukuzawa, M.; Kawata, K.; Nakamori, N.; Kitsunezuka, Y.

2011-03-01

By real-time visual feedback of 3D scatter diagram of pulsatile tissue-motion, freehand ultrasonic diagnosis of neonatal ischemic diseases has been assisted at the bedside. The 2D ultrasonic movie was taken with a conventional ultrasonic apparatus (ATL HDI5000) and ultrasonic probes of 5-7 MHz with the compact tilt-sensor to measure the probe orientation. The real-time 3D visualization was realized by developing an extended version of the PC-based visualization system. The software was originally developed on the DirectX platform and optimized with the streaming SIMD extensions. The 3D scatter diagram of the latest pulsatile tissues has been continuously generated and visualized as projection image with the ultrasonic movie in the current section more than 15 fps. It revealed the 3D structure of pulsatile tissues such as middle and posterior cerebral arteries, Willis ring and cerebellar arteries, in which pediatricians have great interests in the blood flow because asphyxiated and/or low-birth-weight neonates have a high risk of ischemic diseases such as hypoxic-ischemic encephalopathy and periventricular leukomalacia. Since the pulsatile tissue-motion is due to local blood flow, it can be concluded that the system developed in this work is very useful to assist freehand ultrasonic diagnosis of ischemic diseases in the neonatal cranium.

PC-403: Pioneer Venus multiprobe spacecraft mission operational characteristics document, volume 1

NASA Technical Reports Server (NTRS)

Barker, F. C.

1978-01-01

The operational characteristics of the multiprobe system and its subsystem are described. System level, description of the nominal phases, system interfaces, and the capabilities and limitations of system level performance are presented. Bus spacecraft functional and operational descriptions at the subsystem and unit level are presented. The subtleties of nominal operation as well as detailed capabilities and limitations beyond nominal performance are discussed. A command and telemetry logic flow diagram for each subsystem is included. Each diagram identifies in symbolic logic all signal conditioning encountered along each command signal path into, and each telemetry signal path out of the subsystem.

Use of software engineering techniques in the design of the ALEPH data acquisition system

NASA Astrophysics Data System (ADS)

Charity, T.; McClatchey, R.; Harvey, J.

1987-08-01

The SASD methodology is being used to provide a rigorous design framework for various components of the ALEPH data acquisition system. The Entity-Relationship data model is used to describe the layout and configuration of the control and acquisition systems and detector components. State Transition Diagrams are used to specify control applications such as run control and resource management and Data Flow Diagrams assist in decomposing software tasks and defining interfaces between processes. These techniques encourage rigorous software design leading to enhanced functionality and reliability. Improved documentation and communication ensures continuity over the system life-cycle and simplifies project management.

Theoretical regime diagrams for thermally driven flows in a beta-plane channel in the presence of variable gravity

NASA Technical Reports Server (NTRS)

Geisler, J. E.; Fowlis, W. W.

1980-01-01

The effect of a power law gravity field on baroclinic instability is examined, with a focus on the case of inverse fifth power gravity, since this is the power law produced when terrestrial gravity is simulated in spherical geometry by a dielectric force. Growth rates are obtained of unstable normal modes as a function of parameters of the problem by solving a second order differential equation numerically. It is concluded that over the range of parameter space explored, there is no significant change in the character of theoretical regime diagrams if the vertically averaged gravity is used as parameter.

Use of Forward Scattering Particle Image Velocimetry to Quantify a Flow Field Near a Fully Submerged Tension Leg Platform in the Presence of Waves

DTIC Science & Technology

2012-05-01

8217’�/_’ ________ __ � J "Q. F E -3 ¥-------���-------����------------ c( -6 ------------------------------- Time (s) -9...image). Figure 5: Corrected image (left) and vector diagram (right) - wave amplitude of 5.33cm (2.1in) (Wave Crest) ·( J 20 ·0 IS ·0 10 ·0 ( j ...34 ·-0.20 ··0 " -U J ( J Figure 8: Corrected image and vector diagram - wave amplitude of -4.83cm (-1.9in) Figure 9: Corrected image and vector

Public debates driven by incomplete scientific data: The cases of evolution theory, global warming and H1N1 pandemic influenza

NASA Astrophysics Data System (ADS)

Galam, Serge

2010-09-01

Public debates driven by incomplete scientific data where nobody can claim absolute certainty, due to the current state of scientific knowledge, are studied. The cases of evolution theory, global warming and H1N1 pandemic influenza are investigated. The first two are of controversial impact while the third is more neutral and resolved. To adopt a cautious balanced attitude based on clear but inconclusive data appears to be a lose-out strategy. In contrast overstating arguments with incorrect claims which cannot be scientifically refuted appears to be necessary but not sufficient to eventually win a public debate. The underlying key mechanisms of these puzzling and unfortunate conclusions are identified using the Galam sequential probabilistic model of opinion dynamics (Galam, 2002 [4], Galam, 2005 [18], Galam and Jacobs, 2007 [19]). It reveals that the existence of inflexible agents and their respective proportions are the instrumental parameters to determine the faith of incomplete scientific data in public debates. Acting on one’s own inflexible proportion modifies the topology of the flow diagram, which in turn can make irrelevant initial supports. On the contrary focusing on open-minded agents may be useless given some topologies. When the evidence is not as strong as claimed, the inflexibles rather than the data are found to drive the opinion of the population. The results shed a new but disturbing light on designing adequate strategies to win a public debate.

Continuous Personal Improvement.

ERIC Educational Resources Information Center

Emiliani, M. L.

1998-01-01

Suggests that continuous improvement tools used in the workplace can be applied to self-improvement. Explains the use of such techniques as one-piece flow, kanban, visual controls, and total productive maintenance. Points out misapplications of these tools and describes the use of fishbone diagrams to diagnose problems. (SK)

Inflation Fighters.

ERIC Educational Resources Information Center

Cohen, Sheldon H., Ed.

1983-01-01

Describes a low-cost, high-voltage, two-terminal, constant-current source for student use in electrophoresis experiments (includes circuit diagram) and a simple device for the continuous registering of gas flows. Also lists seven cost-saving tips for chemical reagent, including use decorative stones (purchased from nursery stores) in place of…

Automated Design and Evaluation of Airfoils for Rotorcraft Applications

DTIC Science & Technology

2017-12-01

Momentum theory . . . . . . . . . . . . . . . . . . . . . . . 7 2.1.2 Blade -Element and Momentum Theory . . . . . . . . . . . . 10 2.1.2.1 Local Flow...34 3.3.1 Preprocessing . . . . . . . . . . . . . . . . . . . . . . . . . . 34 3.3.2 Run Process...8 2.2 Blade -element diagram . . . . . . . . . . . . . . . . . . . . . . . . . 10 2.3 Rotor flapping motion (Ref. [2

49. Photocopy of scale drawing (from Station 'L' office files, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

49. Photocopy of scale drawing (from Station 'L' office files, Portland, Oregon) Portland General Electric in house drawings, 1930 FLOW DIAGRAM OF THE STEAM GENERATION PROCESS AT STATION 'L' - Portland General Electric Company, Station "L", 1841 Southeast Water Street, Portland, Multnomah County, OR

Enhancing Electrical Troubleshooting Skills in a Computer-Coached Practice Environment.

ERIC Educational Resources Information Center

Johnson, Scott D.; And Others

1993-01-01

This study examines the effect of the "Technical Troubleshooting Tutor," a computer-coached training program, on aircraft electrical system troubleshooting. Performance ability differences between control groups are noted, and troubleshooting models and flow diagram examples are included. The study demonstrates the possibilities for…

Computer program documentation for the pasture/range condition assessment processor

NASA Technical Reports Server (NTRS)

Mcintyre, K. S.; Miller, T. G. (Principal Investigator)

1982-01-01

The processor which drives for the RANGE software allows the user to analyze LANDSAT data containing pasture and rangeland. Analysis includes mapping, generating statistics, calculating vegetative indexes, and plotting vegetative indexes. Routines for using the processor are given. A flow diagram is included.

Teaching Electricity.

ERIC Educational Resources Information Center

Iona, Mario

1982-01-01

To clarify the meaning of electrical terms, a chart is used to compare electrical concepts and relationships with a more easily visualized system in which water flows from a hilltop reservoir through a pipe to drive a mill at the bottom of the hill. A diagram accompanies the chart. (Author/SK)

166. Photocopy of drawing (1979 piping drawing by StearnsRoger Incorporated) ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

166. Photocopy of drawing (1979 piping drawing by Stearns-Roger Incorporated) HELIUM AND NITROGEN PUMPING SYSTEMS FLOW DIAGRAM, SHEET 511-P6 - Vandenberg Air Force Base, Space Launch Complex 3, Launch Pad 3 West, Napa & Alden Roads, Lompoc, Santa Barbara County, CA

Phase behavior, rheological characteristics and microstructure of sodium caseinate-Persian gum system.

PubMed

Sadeghi, Farzad; Kadkhodaee, Rassoul; Emadzadeh, Bahareh; Phillips, Glyn O

2018-01-01

In this study, the phase behavior of sodium caseinate-Persian gum mixtures was investigated. The effect of thermodynamic incompatibility on phase distribution of sodium caseinate fractions as well as the flow behavior and microstructure of the biopolymer mixtures were also studied. The phase diagram clearly demonstrated the dominant effect of Persian gum on the incompatibility of the two biopolymers. SDS-PAGE electrophoresis indicated no selective fractionation of sodium caseinate subunits between equilibrium phases upon de-mixing. The microstructure of mixtures significantly changed depending on their position within the phase diagram. Fitting viscometric data to Cross and Bingham models revealed that the apparent viscosity, relaxation time and shear thinning behavior of the mixtures is greatly influenced by the volume ratio and concentration of the equilibrium phases. There is a strong dependence of the flow behavior of sodium caseinate-Persian gum mixtures on the composition of the equilibrium phases and the corresponding microstructure of the system. Copyright © 2017. Published by Elsevier Ltd.

Effects of iterative learning based signal control strategies on macroscopic fundamental diagrams of urban road networks

NASA Astrophysics Data System (ADS)

Yan, Fei; Tian, Fuli; Shi, Zhongke

2016-10-01

Urban traffic flows are inherently repeated on a daily or weekly basis. This repeatability can help improve the traffic conditions if it is used properly by the control system. In this paper, we propose a novel iterative learning control (ILC) strategy for traffic signals of urban road networks using the repeatability feature of traffic flow. To improve the control robustness, the ILC strategy is further integrated with an error feedback control law in a complementary manner. Theoretical analysis indicates that the ILC-based traffic signal control methods can guarantee the asymptotic learning convergence, despite the presence of modeling uncertainties and exogenous disturbances. Finally, the impacts of the ILC-based signal control strategies on the network macroscopic fundamental diagram (MFD) are examined. The results show that the proposed ILC-based control strategies can homogenously distribute the network accumulation by controlling the vehicle numbers in each link to the desired levels under different traffic demands, which can result in the network with high capacity and mobility.

Ultrasound Velocity Measurements in High-Chromium Steel Under Plastic Deformation

NASA Astrophysics Data System (ADS)

Lunev, Aleksey; Bochkareva, Anna; Barannikova, Svetlana; Zuev, Lev

2016-04-01

In the present study, the variation of the propagation velocity of ultrasound in the plastic deformation of corrosion-resistant high-chromium steel 40X13 with ferrite-carbide (delivery status), martensitic (quenched) and sorbitol (after high-temperature tempering) structures have beem studied/ It is found that each state shows its view of the loading curve. In the delivery state diagram loading is substantially parabolic throughout, while in the martensitic state contains only linear strain hardening step and in the sorbitol state the plastic flow curve is three-step. The velocity of ultrasonic surface waves (Rayleigh waves) was measured simultaneously with the registration of the loading curve in the investigated steel in tension. It is shown that the dependence of the velocity of ultrasound in active loading is determined by the law of plastic flow, that is, the staging of the corresponding diagram of loading. Structural state of the investigated steel is not only changing the type of the deformation curve under uniaxial tension, but also changes the nature of ultrasound speed of deformation.

Repeated surveys by acoustic Doppler current profiler for flow and sediment dynamics in a tidal river

USGS Publications Warehouse

Dinehart, R.L.; Burau, J.R.

2005-01-01

A strategy of repeated surveys by acoustic Doppler current profiler (ADCP) was applied in a tidal river to map velocity vectors and suspended-sediment indicators. The Sacramento River at the junction with the Delta Cross Channel at Walnut Grove, California, was surveyed over several tidal cycles in the Fall of 2000 and 2001 with a vessel-mounted ADCP. Velocity profiles were recorded along flow-defining survey paths, with surveys repeated every 27 min through a diurnal tidal cycle. Velocity vectors along each survey path were interpolated to a three-dimensional Cartesian grid that conformed to local bathymetry. A separate array of vectors was interpolated onto a grid from each survey. By displaying interpolated vector grids sequentially with computer animation, flow dynamics of the reach could be studied in three-dimensions as flow responded to the tidal cycle. Velocity streamtraces in the grid showed the upwelling of flow from the bottom of the Sacramento River channel into the Delta Cross Channel. The sequential display of vector grids showed that water in the canal briefly returned into the Sacramento River after peak flood tides, which had not been known previously. In addition to velocity vectors, ADCP data were processed to derive channel bathymetry and a spatial indicator for suspended-sediment concentration. Individual beam distances to bed, recorded by the ADCP, were transformed to yield bathymetry accurate enough to resolve small bedforms within the study reach. While recording velocity, ADCPs also record the intensity of acoustic backscatter from particles suspended in the flow. Sequential surveys of backscatter intensity were interpolated to grids and animated to indicate the spatial movement of suspended sediment through the study reach. Calculation of backscatter flux through cross-sectional grids provided a first step for computation of suspended-sediment discharge, the second step being a calibrated relation between backscatter intensity and sediment concentration. Spatial analyses of ADCP data showed that a strategy of repeated surveys and flow-field interpolation has the potential to simplify computation of flow and sediment discharge through complex waterways. The use of trade, product, industry, or firm names in this report is for descriptive purposes only and does not constitute endorsement of products by the US Government. ?? 2005 Elsevier B.V. All rights reserved.

3D Band Diagram and Photoexcitation of 2D-3D Semiconductor Heterojunctions.

PubMed

Li, Bo; Shi, Gang; Lei, Sidong; He, Yongmin; Gao, Weilu; Gong, Yongji; Ye, Gonglan; Zhou, Wu; Keyshar, Kunttal; Hao, Ji; Dong, Pei; Ge, Liehui; Lou, Jun; Kono, Junichiro; Vajtai, Robert; Ajayan, Pulickel M

2015-09-09

The emergence of a rich variety of two-dimensional (2D) layered semiconductor materials has enabled the creation of atomically thin heterojunction devices. Junctions between atomically thin 2D layers and 3D bulk semiconductors can lead to junctions that are fundamentally electronically different from the covalently bonded conventional semiconductor junctions. Here we propose a new 3D band diagram for the heterojunction formed between n-type monolayer MoS2 and p-type Si, in which the conduction and valence band-edges of the MoS2 monolayer are drawn for both stacked and in-plane directions. This new band diagram helps visualize the flow of charge carriers inside the device in a 3D manner. Our detailed wavelength-dependent photocurrent measurements fully support the diagrams and unambiguously show that the band alignment is type I for this 2D-3D heterojunction. Photogenerated electron-hole pairs in the atomically thin monolayer are separated and driven by an external bias and control the "on/off" states of the junction photodetector device. Two photoresponse regimes with fast and slow relaxation are also revealed in time-resolved photocurrent measurements, suggesting the important role played by charge trap states.

Airfoil shape for flight at subsonic speeds. [design analysis and aerodynamic characteristics of the GAW-1 airfoil

NASA Technical Reports Server (NTRS)

Whitcomb, R. T. (Inventor)

1976-01-01

An airfoil is examined that has an upper surface shaped to control flow accelerations and pressure distribution over the upper surface and to prevent separation of the boundary layer due to shock wave formulation at high subsonic speeds well above the critical Mach number. A highly cambered trailing edge section improves overall airfoil lifting efficiency. Diagrams illustrating supersonic flow and shock waves over the airfoil are shown.

Chemical Reactions in Turbulent Mixing Flows.

DTIC Science & Technology

1987-06-01

longer in the z-t diagrams for higher fuel flow rates (consistent with longer flame lengths ) and, further, the celerity of a structure at a given axial...clocking rate synchronized with the cycle, while the slower clocking rate data corres- pond to about seven cycles. Flame lengths [61, Z,,D, for various...heat fABlLE I releases studied here are also shown in Table I Flame Lengths and Axial Measurement Stations, These flame lengths are based on 50% intermit

Molecular Diagnostics for the Study of Hypersonic Flows

DTIC Science & Technology

2000-04-01

between the at the F4 high-enthalpy wind tunnel [21]. Figure 5 electrodes. The fast electrons exit the anode disk shows the image acquired 90 ms after...Discharge Figure 5 Typical F4 run, flow at 90 ms , Grounded Electrode convection imaged 5 jis after beam emission. Figure 4 Schematic diagram of the...accounts for the classical phenomena like absorption and Figure 6 Velocity profile at 90 ms for run of refraction. X(2) is the second-order

The study of insect blood-feeding behaviour. 2. Recording techniques and the use of flow charts.

PubMed

Smith, J J; Friend, W G

1987-01-01

This paper continues a discussion of approaches and methodologies we have used in our studies of feeding in haematophagous insects. Described are techniques for directly monitoring behaviour: electrical recording of feeding behaviour via resistance changes in the food canal, optical methods for monitoring mouthpart activity, and a computer technique for behavioural event recording. Also described is the use of "flow charts" or "decision diagrams" to model interrelated sequences of behaviours.