Large-Scale Biaxial Friction Experiments with an Assistance of the NIED Shaking Table

NASA Astrophysics Data System (ADS)

Fukuyama, E.; Mizoguchi, K.; Yamashita, F.; Togo, T.; Kawakata, H.; Yoshimitsu, N.; Shimamoto, T.; Mikoshiba, T.; Sato, M.; Minowa, C.

2012-12-01

We constructed a large-scale biaxial friction apparatus using a large shaking table working at NIED (table dimension is 15m x 15m). The actuator of the shaking table becomes the engine of the constant speed loading. We used a 1.5m long rock sample overlaid on a 2m one. Their height and width are both 0.5m. Therefore, the slip area is 1.5m x 0.5m. The 2m long sample moves with the shaking table and the 1.5m sample is fixed to the basement of the shaking table. Thus, the shaking table displacement controls the dislocation between two rock samples. The shaking table can generate 0.4m displacement with a velocity ranging between 0.0125mm/s and 1m/s. We used Indian gabbro for the rock sample of the present experiments. Original flatness of the sliding surface was formed less than 0.024mm undulation using a large-scale plane grinder. Surface roughness evolved as subsequent experiments were done. Wear material was generated during each experiment, whose grain size becomes bigger as the experiments proceed. This might suggest a damage evolution on the sliding surface. In some experiments we did not remove the gouge material before sliding to examine the effect of gouge layer. Normal stress can be applied up to 1.3MPa. The stiffness of this apparatus was measured experimentally and was of the order of 0.1GN/m. We first measured the coefficient of friction at low sliding velocity (0.1~1mm/s) where the steady state was achieved after the slip of ~5mm. The coefficient of friction was about 0.75 under the normal stress between 0.13 and 1.3MPa. This is consistent with those estimated by previous works using smaller rock samples. We observed that the coefficient of friction decreased gradually with increasing slip velocity, but simultaneously the friction curves at the higher velocities are characterized by stick-slip vibration. Our main aim of the experiments is to understand the rupture propagation from slow nucleation to fast unstable rupture during the loading of two contact surfaces. We recorded many unstable slip events that nucleated inside the sliding surface but did not reach the edge of the sliding surface until the termination of slip. These slip events simulate full rupture process during earthquake, including nucleation, propagation and termination of the rupture. We monitored these rupture progress using the strain change propagation measured by 16 semiconductor strain gauges recorded at a sampling rate of 1MHz. In addition, high frequency waves emitted from AE events was continuously observed by 8 piezo-electronic transducers (PZTs) at a sampling rate of 20MHz. These sensors were attached at the edge of the slipping area. The AE event started to occur where the slip was nucleated and the slip area started to expand. Unfortunately, we could not locate all AE events during the unstable rupture, because of the overprints of signals from multiple events in the PZT records. We also monitored the amplitudes of transmitted waves across the sliding surface. The amplitudes decreased just after the stick slip and recovered gradually, suggesting that the transmitted wave amplitudes might reflect the slipped area on the interface.

Estimation of Stresses in a Dry Sand Layer Tested on Shaking Table

NASA Astrophysics Data System (ADS)

Sawicki, Andrzej; Kulczykowski, Marek; Jankowski, Robert

2012-12-01

Theoretical analysis of shaking table experiments, simulating earthquake response of a dry sand layer, is presented. The aim of such experiments is to study seismic-induced compaction of soil and resulting settlements. In order to determine the soil compaction, the cyclic stresses and strains should be calculated first. These stresses are caused by the cyclic horizontal acceleration at the base of soil layer, so it is important to determine the stress field as function of the base acceleration. It is particularly important for a proper interpretation of shaking table tests, where the base acceleration is controlled but the stresses are hard to measure, and they can only be deduced. Preliminary experiments have shown that small accelerations do not lead to essential settlements, whilst large accelerations cause some phenomena typical for limit states, including a visible appearance of slip lines. All these problems should be well understood for rational planning of experiments. The analysis of these problems is presented in this paper. First, some heuristic considerations about the dynamics of experimental system are presented. Then, the analysis of boundary conditions, expressed as resultants of respective stresses is shown. A particular form of boundary conditions has been chosen, which satisfies the macroscopic boundary conditions and the equilibrium equations. Then, some considerations are presented in order to obtain statically admissible stress field, which does not exceed the Coulomb-Mohr yield conditions. Such an approach leads to determination of the limit base accelerations, which do not cause the plastic state in soil. It was shown that larger accelerations lead to increase of the lateral stresses, and the respective method, which may replace complex plasticity analyses, is proposed. It is shown that it is the lateral stress coefficient K0 that controls the statically admissible stress field during the shaking table experiments.

Using Smartphones to Detect Earthquakes

NASA Astrophysics Data System (ADS)

Kong, Q.; Allen, R. M.

2012-12-01

We are using the accelerometers in smartphones to record earthquakes. In the future, these smartphones may work as a supplement network to the current traditional network for scientific research and real-time applications. Given the potential number of smartphones, and small separation of sensors, this new type of seismic dataset has significant potential provides that the signal can be separated from the noise. We developed an application for android phones to record the acceleration in real time. These records can be saved on the local phone or transmitted back to a server in real time. The accelerometers in the phones were evaluated by comparing performance with a high quality accelerometer while located on controlled shake tables for a variety of tests. The results show that the accelerometer in the smartphone can reproduce the characteristic of the shaking very well, even the phone left freely on the shake table. The nature of these datasets is also quite different from traditional networks due to the fact that smartphones are moving around with their owners. Therefore, we must distinguish earthquake signals from other daily use. In addition to the shake table tests that accumulated earthquake records, we also recorded different human activities such as running, walking, driving etc. An artificial neural network based approach was developed to distinguish these different records. It shows a 99.7% successful rate of distinguishing earthquakes from the other typical human activities in our database. We are now at the stage ready to develop the basic infrastructure for a smartphone seismic network.

ARC-2007-ACD07-0073-046

NASA Image and Video Library

2007-04-14

Lunar CRater Observation and Sensing Satellite (LCROSS) and P.I. at NASA Ames Research Center - Total Luminance Photometer shake test in N-244 (EEL) : Metal shake table close up. Shows two units bolted on. The left one is the lens, sensor electronics and photometer sensor. The right is the digital electronics unit for the instrument. The two units, along with their cabling is one of the LCROSS science insruments.

Shake-table testing of a self-centering precast reinforced concrete frame with shear walls

NASA Astrophysics Data System (ADS)

Lu, Xilin; Yang, Boya; Zhao, Bin

2018-04-01

The seismic performance of a self-centering precast reinforced concrete (RC) frame with shear walls was investigated in this paper. The lateral force resistance was provided by self-centering precast RC shear walls (SPCW), which utilize a combination of unbonded prestressed post-tensioned (PT) tendons and mild steel reinforcing bars for flexural resistance across base joints. The structures concentrated deformations at the bottom joints and the unbonded PT tendons provided the self-centering restoring force. A 1/3-scale model of a five-story self-centering RC frame with shear walls was designed and tested on a shake-table under a series of bi-directional earthquake excitations with increasing intensity. The acceleration response, roof displacement, inter-story drifts, residual drifts, shear force ratios, hysteresis curves, and local behaviour of the test specimen were analysed and evaluated. The results demonstrated that seismic performance of the test specimen was satisfactory in the plane of the shear wall; however, the structure sustained inter-story drift levels up to 2.45%. Negligible residual drifts were recorded after all applied earthquake excitations. Based on the shake-table test results, it is feasible to apply and popularize a self-centering precast RC frame with shear walls as a structural system in seismic regions.

System identification of timber masonry walls using shaking table test

NASA Astrophysics Data System (ADS)

Roy, Timir B.; Guerreiro, Luis; Bagchi, Ashutosh

2017-04-01

Dynamic study is important in order to design, repair and rehabilitation of structures. It has played an important role in the behavior characterization of structures; such as: bridges, dams, high rise buildings etc. There had been substantial development in this area over the last few decades, especially in the field of dynamic identification techniques of structural systems. Frequency Domain Decomposition (FDD) and Time Domain Decomposition are most commonly used methods to identify modal parameters; such as: natural frequency, modal damping and mode shape. The focus of the present research is to study the dynamic characteristics of typical timber masonry walls commonly used in Portugal. For that purpose, a multi-storey structural prototype of such wall has been tested on a seismic shake table at the National Laboratory for Civil Engineering, Portugal (LNEC). Signal processing has been performed of the output response, which is collected from the shaking table experiment of the prototype using accelerometers. In the present work signal processing of the output response, based on the input response has been done in two ways: FDD and Stochastic Subspace Identification (SSI). In order to estimate the values of the modal parameters, algorithms for FDD are formulated and parametric functions for the SSI are computed. Finally, estimated values from both the methods are compared to measure the accuracy of both the techniques.

Research on multi-parameter monitoring of steel frame shaking-table test using smartphone

NASA Astrophysics Data System (ADS)

Han, Ruicong; Loh, Kenneth J.; Zhao, Xuefeng; Yu, Yan

2017-04-01

The numerical simulation promises an effective method to assess seismic damage of high-rise structure. But it's difficult to determine the input parameters and the simulation results are not completely consistent with the real condition. A more direct approach to evaluate the seismic damage is the structural health monitoring (SHM), which is one complex set of various kinds of sensors, devices and software, and always needs professionals. SHM system has achieved great development over recent years, especially on bridge structures. However it's not so popular on high-rise building due to its difficult implementation. Developing a low-cost and convenient monitoring technique will be helpful for the safety maintenance of high-rise building. Smartphones, which embedded with sensors, network transmission, data storage and processing system, are evolving towards crowdsourcing. The popularity of smartphones presents opportunities for implementation of portable SHM system on buildings. In this paper, multi-parameter monitoring of a three-story steel frame on shaking table under earthquake excitations was conducted with smartphone, and the comparison between smartphone and traditional sensors was provided. First, the monitoring applications on iOS platform, Orion-CC and D-viewer, were introduced. Then the experimental details were presented, including three-story frame model, sensors placement, viscous dampers and so on. Last, the acceleration and displacement time-history curves of smartphone and traditional sensors are provided and compared to prove the feasibility of the monitoring on frame under earthquake excitations by smartphone.

Semi-active tuned liquid column damper implementation with real-time hybrid simulations

NASA Astrophysics Data System (ADS)

Riascos, Carlos; Marulanda Casas, Johannio; Thomson, Peter

2016-04-01

Real-time hybrid simulation (RTHS) is a modern cyber-physical technique used for the experimental evaluation of complex systems, that treats the system components with predictable behavior as a numerical substructure and the components that are difficult to model as an experimental substructure. Therefore it is an attractive method for evaluation of the response of civil structures under earthquake, wind and anthropic loads. In this paper, the response of three-story shear frame controlled by a tuned liquid column damper (TLCD) and subject to base excitation is considered. Both passive and semi-active control strategies were implemented and are compared. While the passive TLCD achieved a reduction of 50% in the acceleration response of the main structure in comparison with the structure without control, the semi-active TLCD achieved a reduction of 70%, and was robust to variations in the dynamic properties of the main structure. In addition, a RTHS was implemented with the main structure modeled as a linear, time-invariant (LTI) system through a state space representation and the TLCD, with both control strategies, was evaluated on a shake table that reproduced the displacement of the virtual structure. Current assessment measures for RTHS were used to quantify the performance with parameters such as generalized amplitude, equivalent time delay between the target and measured displacement of the shake table, and energy error using the measured force, and prove that the RTHS described in this paper is an accurate method for the experimental evaluation of structural control systems.

Non-Linear Material Three Degree of Freedom Analysis of Submarine Drydock Blocking System

DTIC Science & Technology

1988-05-01

drydock blocking materials laminates should be used. For example, if laminated oak timbers are judged to be suitable they would exhibit a minimum of...1/4 of the strength variation of solid timbers . They would not have the inherent defects of large sawn timbers such as grain slope, checks, shakes ,and...experiments on this concept have been carried out over the last few years using the shaking table at the Earthquake Engineering Research Center

SHAKING TABLE TEST AND EFFECTIVE STRESS ANALYSIS ON SEISMIC PERFORMANCE WITH SEISMIC ISOLATION RUBBER TO THE INTERMEDIATE PART OF PILE FOUNDATION IN LIQUEFACTION

NASA Astrophysics Data System (ADS)

Uno, Kunihiko; Otsuka, Hisanori; Mitou, Masaaki

The pile foundation is heavily damaged at the boundary division of the ground types, liquefied ground and non-liquefied ground, during an earthquake and there is a possibility of the collapse of the piles. In this study, we conduct a shaking table test and effective stress analysis of the influence of soil liquefaction and the seismic inertial force exerted on the pile foundation. When the intermediate part of the pile, there is at the boundary division, is subjected to section force, this part increases in size as compared to the pile head in certain instances. Further, we develop a seismic resistance method for a pile foundation in liquefaction using seismic isolation rubber and it is shown the middle part seismic isolation system is very effective.

ARC-2007-ACD07-0073-050

NASA Image and Video Library

2007-04-14

Lunar CRater Observation and Sensing Satellite (LCROSS) and P.I. at NASA Ames Research Center - Total Luminance Photometer lens and electronics units on shake table in N-2444 EEL Laboratory: Kim Ennico and Gi Kojima check electronics

ARC-2007-ACD07-0073-048

NASA Image and Video Library

2007-04-14

Lunar CRater Observation and Sensing Satellite (LCROSS) and P.I. at NASA Ames Research Center - Total Luminance Photometer lens and electronics units on shake table in N-2444 EEL Laboratory with (l) Gi Kojima (bk - middle) Damon Flansburg (r) Dana Lynch

Occupant Motion Sensors : Rotational Accelerometer Development

DOT National Transportation Integrated Search

1972-04-01

A miniature mouthpiece rotational accelerometer has been developed to measure the angular acceleration of a head during vehicle crash or impact conditions. The device has been tested in the laboratory using a shake table and in the field using dummie...

Structural assessment of highway "N" power substation under earthquake loads.

DOT National Transportation Integrated Search

2009-10-01

In this study, the Highway N Substation was analyzed with a finite element model (FEM) for its vulnerability. The rigid bus and electric switch components were characterized with full scale shake table tests. Each component of the substation wa...

ARC-2007-ACD07-0073-052

NASA Image and Video Library

2007-04-14

Lunar CRater Observation and Sensing Satellite (LCROSS) and P.I. at NASA Ames Research Center - Total Luminance Photometer lens and electronics units on shake table in N-2444 EEL Laboratory: Gi Kojima, Dana Lynch and Lynn Hofland check electronics. Data analyzer is the foreground.

40 CFR 440.141 - Specialized definitions and provisions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... shaking tables. (7) “Infiltration water” means that water which permeates through the earth into the plant... drainage, and infiltration and drainage waters which commingle with mine drainage or waters resulting from... increase in volume from precipitation or infiltration, plus the maximum volume of water runoff resulting...

40 CFR 440.141 - Specialized definitions and provisions.

Code of Federal Regulations, 2014 CFR

2014-07-01

..., hydrocyclones, or shaking tables. (7) “Infiltration water” means that water which permeates through the earth... drainage, and infiltration and drainage waters which commingle with mine drainage or waters resulting from... increase in volume from precipitation or infiltration, plus the maximum volume of water runoff resulting...

40 CFR 440.141 - Specialized definitions and provisions.

Code of Federal Regulations, 2013 CFR

2013-07-01

..., hydrocyclones, or shaking tables. (7) “Infiltration water” means that water which permeates through the earth... drainage, and infiltration and drainage waters which commingle with mine drainage or waters resulting from... increase in volume from precipitation or infiltration, plus the maximum volume of water runoff resulting...

40 CFR 440.141 - Specialized definitions and provisions.

Code of Federal Regulations, 2012 CFR

2012-07-01

..., hydrocyclones, or shaking tables. (7) “Infiltration water” means that water which permeates through the earth... drainage, and infiltration and drainage waters which commingle with mine drainage or waters resulting from... increase in volume from precipitation or infiltration, plus the maximum volume of water runoff resulting...

40 CFR 440.141 - Specialized definitions and provisions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... shaking tables. (7) “Infiltration water” means that water which permeates through the earth into the plant... drainage, and infiltration and drainage waters which commingle with mine drainage or waters resulting from... increase in volume from precipitation or infiltration, plus the maximum volume of water runoff resulting...

The quest for better quality-of-life - learning from large-scale shaking table tests

NASA Astrophysics Data System (ADS)

Nakashima, M.; Sato, E.; Nagae, T.; Kunio, F.; Takahito, I.

2010-12-01

Earthquake engineering has its origins in the practice of “learning from actual earthquakes and earthquake damages.” That is, we recognize serious problems by witnessing the actual damage to our structures, and then we develop and apply engineering solutions to solve these problems. This tradition in earthquake engineering, i.e., “learning from actual damage,” was an obvious engineering response to earthquakes and arose naturally as a practice in a civil and building engineering discipline that traditionally places more emphasis on experience than do other engineering disciplines. But with the rapid progress of urbanization, as society becomes denser, and as the many components that form our society interact with increasing complexity, the potential damage with which earthquakes threaten the society also increases. In such an era, the approach of ”learning from actual earthquake damages” becomes unacceptably dangerous and expensive. Among the practical alternatives to the old practice is to “learn from quasi-actual earthquake damages.” One tool for experiencing earthquake damages without attendant catastrophe is the large shaking table. E-Defense, the largest one we have, was developed in Japan after the 1995 Hyogoken-Nanbu (Kobe) earthquake. Since its inauguration in 2005, E-Defense has conducted over forty full-scale or large-scale shaking table tests, applied to a variety of structural systems. The tests supply detailed data on actual behavior and collapse of the tested structures, offering the earthquake engineering community opportunities to experience and assess the actual seismic performance of the structures, and to help society prepare for earthquakes. Notably, the data were obtained without having to wait for the aftermaths of actual earthquakes. Earthquake engineering has always been about life safety, but in recent years maintaining the quality of life has also become a critical issue. Quality-of-life concerns include nonstructural damage, business continuity, public health, quickness of damage assessment, infrastructure, data and communication networks, and other issues, and not enough useful empirical data have emerged about these issues from the experiences of actual earthquakes. To provide quantitative data that can be used to reduce earthquake risk to our quality of life, E-Defense recently has been implementing two comprehensive research projects in which a base-isolated hospital and a steel high-rise building were tested using the E-Defense shaking table and their seismic performance were examined particularly in terms of the nonstructural damage, damage to building contents and furniture, and operability, functionality, and business-continuity capability. The paper presents the overview of the two projects, together with major findings obtained from the projects.

The 21 May 2014 Mw 5.9 Bay of Bengal earthquake: macroseismic data suggest a high‐stress‐drop event

USGS Publications Warehouse

Martin, Stacey; Hough, Susan E.

2015-01-01

A modest but noteworthy Mw 5.9 earthquake occurred in the Bay of Bengal beneath the central Bengal fan at 21:51 Indian Standard Time (16:21 UTC) on 21 May 2014. Centered over 300 km from the eastern coastline of India (Fig. 1), it caused modest damage by virtue of its location and magnitude. However, shaking was very widely felt in parts of eastern India where earthquakes are uncommon. Media outlets reported as many as four fatalities. Although most deaths were blamed on heart attacks, the death of one woman was attributed by different sources to either a roof collapse or a stampede (see Table S1, available in the electronic supplement to this article). Across the state of Odisha, as many as 250 people were injured (see Table S1), most after jumping from balconies or terraces. Light damage was reported from a number of towns on coastal deltaic sediments, including collapsed walls and damage to pukka and thatched dwellings. Shaking was felt well inland into east‐central India and was perceptible in multistoried buildings as far as Chennai, Delhi, and Jaipur at distances of ≈1600  km (Table 1).

Shake Warning: Helping People Stay Safe With Lots of Small Boxes in the Ground to Warn Them About Strong Shaking

NASA Astrophysics Data System (ADS)

Reusch, M.

2017-12-01

A group of people at schools are joining with the group of people in control of making pictures of the state of rocks on the ground and water in our land. They are working on a plan to help all people be safe in the case of very big ground shaking (when ground breaks in sight or under ground). They will put many small boxes all over the states in the direction of where the sun sets to look for the first shake that might be a sign of an even bigger shake to come. They tell a big computer (with much power) in several large cities in those states. These computers will decide if the first shake is a sign of a very large and close ground shake, a far-away ground shake, a small but close ground shake, or even just a sign of a shake that people wanted to make. If it is a sign of a close and really big shake, then the computers will tell the phones and computers of many people to help them take safe steps before the big shaking arrives where they are. This warning might be several seconds or maybe a couple of minutes. People will be able to hide, take cover, and hold on under tables and desks in case things fall from walls and places up high in their home and work. Doctors will be able to pause hard work and boxes that move people up and down in homes, businesses, and stores will be able to stop on the next floor and open their doors to let people out and not get stuck. It will help slow down trains to be safe and not fly off of the track as well as it will help to shut off water and air that warms homes and is used for when you make food hot. To make this plan become real, people who work for these groups are putting more small boxes in areas where there are not enough and that there are many people. They are also putting small boxes in places where there are no boxes but the big shake might come from that direction. There are problems to get past such as needing many more small boxes, more people to help with this plan, and getting all people who live in these areas to learn what to do when the warning comes about the big shake, but this year there was good news when in month number four they were able to get all of the computers to talk to each other and run the same plan with the same news of the first shaking.

Introducing Students to Structural Dynamics and Earthquake Engineering

ERIC Educational Resources Information Center

Anthoine, Armelle; Marazzi, Francesco; Tirelli, Daniel

2010-01-01

The European Laboratory for Structural Assessment (ELSA) is one of the world's main laboratories for seismic studies. Besides its research activities, it also aims to bring applied science closer to the public. This article describes teaching activities based on a demonstration shaking table which is used to introduce the structural dynamics of…

40 CFR 799.6755 - TSCA partition coefficient (n-octanol/water), shake flask method.

Code of Federal Regulations, 2013 CFR

2013-07-01

...) Qualifying statements. This method applies only to pure, water soluble substances which do not dissociate or... applies to a pure substance dispersed between two pure solvents. If several different solutes occur in one... applied. The values presented in table 1 of this section are not necessarily representative of the results...

40 CFR 799.6755 - TSCA partition coefficient (n-octanol/water), shake flask method.

Code of Federal Regulations, 2014 CFR

2014-07-01

...) Qualifying statements. This method applies only to pure, water soluble substances which do not dissociate or... applied. The values presented in table 1 of this section are not necessarily representative of the results... Law applies only at constant temperature, pressure, and pH for dilute solutions. It strictly applies...

ARC-2007-ACD07-0073-044

NASA Image and Video Library

2007-04-14

Lunar CRater Observation and Sensing Satellite (LCROSS) and P.I. at NASA Ames Research Center - (l to r) Kim Ennico, Damon Flansburg and Gi Kojima check out the LCROSS Total Luminance Photometer lens and electronics attached to a metal plate in preparation for a vibe (vibration) test on the shake table in N-2444 EEL Laboratory

California's forest products industry: 1985.

Treesearch

James O. Howard; Franklin R. Ward

1988-01-01

This report presents the findings of a 100-percent survey of the primary forest products industry in California for 1985. The survey included the following sectors: lumber; veneer and plywood; pulp and board; shake and shingle; export; and post, pole, and piling. Tables, presented by sector and for the industry as a whole, include characteristics of the industry,...

California's forest products industry: 1992.

Treesearch

Franklin R. Ward

1995-01-01

This report presents the findings of a survey of primary forest products industries in California for 1992. The survey included the following sectors: lumber; pulp and board; shake and shingle; export; and post, pole, and piling. Veneer and plywood mills are not included because they could not be presented without disclosing critical details. Tables, presented by...

California's forest products industry: 1994.

Treesearch

Franklin R. Ward

1997-01-01

This report presents the findings of a survey of primary forest products industries in California for 1994. The survey included the following sectors: lumber; veneer; pulp and board; shake and shingle; export; and post, pole, and piling. Tables, presented by sector and for the industry as a whole, include characteristics of the industry, nature and flow of logs...

Building a Smartphone Seismic Network

NASA Astrophysics Data System (ADS)

Kong, Q.; Allen, R. M.

2013-12-01

We are exploring to build a new type of seismic network by using the smartphones. The accelerometers in smartphones can be used to record earthquakes, the GPS unit can give an accurate location, and the built-in communication unit makes the communication easier for this network. In the future, these smartphones may work as a supplement network to the current traditional network for scientific research and real-time applications. In order to build this network, we developed an application for android phones and server to record the acceleration in real time. These records can be sent back to a server in real time, and analyzed at the server. We evaluated the performance of the smartphone as a seismic recording instrument by comparing them with high quality accelerometer while located on controlled shake tables for a variety of tests, and also the noise floor test. Based on the daily human activity data recorded by the volunteers and the shake table tests data, we also developed algorithm for the smartphones to detect earthquakes from daily human activities. These all form the basis of setting up a new prototype smartphone seismic network in the near future.

Experimental and analytical studies on multiple tuned mass dampers for seismic protection of porcelain electrical equipment

NASA Astrophysics Data System (ADS)

Bai, Wen; Dai, Junwu; Zhou, Huimeng; Yang, Yongqiang; Ning, Xiaoqing

2017-10-01

Porcelain electrical equipment (PEE), such as current transformers, is critical to power supply systems, but its seismic performance during past earthquakes has not been satisfactory. This paper studies the seismic performance of two typical types of PEE and proposes a damping method for PEE based on multiple tuned mass dampers (MTMD). An MTMD damping device involving three mass units, named a triple tuned mass damper (TTMD), is designed and manufactured. Through shake table tests and finite element analysis, the dynamic characteristics of the PEE are studied and the effectiveness of the MTMD damping method is verified. The adverse influence of MTMD redundant mass to damping efficiency is studied and relevant equations are derived. MTMD robustness is verified through adjusting TTMD control frequencies. The damping effectiveness of TTMD, when the peak ground acceleration far exceeds the design value, is studied. Both shake table tests and finite element analysis indicate that MTMD is effective and robust in attenuating PEE seismic responses. TTMD remains effective when the PGA far exceeds the design value and when control deviations are considered.

Shake table tests of suspended ceilings to simulate the observed damage in the M s7.0 Lushan earthquake, China

NASA Astrophysics Data System (ADS)

Wang, Duozhi; Dai, Junwu; Qu, Zhe; Ning, Xiaoqing

2016-06-01

Severe damage to suspended ceilings of metal grids and lay-in panels was observed in public buildings during the 2013 M s7.0 Lushan earthquake in China. Over the past several years, suspended ceilings have been widely used practice in public buildings throughout China, including government offices, schools and hospitals. To investigate the damage mechanism of suspended ceilings, a series of three-dimensional shake table tests was conducted to reproduce the observed damage. A full-scale reinforced concrete frame was constructed as the testing frame for the ceiling, which was single-story and infilled with brick masonry walls to represent the local construction of low-rise buildings. In general, the ceiling in the tests exhibited similar damage phenomena as the field observations, such as higher vulnerability of perimeter elements and extensive damage to the cross runners. However, it exhibited lower fragility in terms of peak ground/roof accelerations at the initiation of damage. Further investigations are needed to clarify the reasons for this behavior.

Performance of sand and shredded rubber tire mixture as a natural base isolator for earthquake protection

NASA Astrophysics Data System (ADS)

Bandyopadhyay, Srijit; Sengupta, Aniruddha; Reddy, G. R.

2015-12-01

The performance of a well-designed layer of sand, and composites like layer of sand mixed with shredded rubber tire (RSM) as low cost base isolators, is studied in shake table tests in the laboratory. The building foundation is modeled by a 200 mm by 200 mm and 40 mm thick rigid plexi-glass block. The block is placed in the middle of a 1m by 1m tank filled with sand. The selected base isolator is placed between the block and the sand foundation. Accelerometers are placed on top of the footing and foundation sand layer. The displacement of the footing is also measured by LVDT. The whole setup is mounted on a shake table and subjected to sinusoidal motions with varying amplitude and frequency. Sand is found to be effective only at very high amplitude (> 0.65 g) of motions. The performance of a composite consisting of sand and 50% shredded rubber tire placed under the footing is found to be most promising as a low-cost effective base isolator.

Optimization of wet shaking table process using response surface methodology applied to the separation of copper and aluminum from the fine fraction of shredder ELVs.

PubMed

Jordão, Helga; Sousa, António Jorge; Carvalho, M Teresa

2016-02-01

With the purpose of reducing the waste generated by end-of-life vehicles (ELVs) by enhancing the recovery and recycling of nonferrous metals, an experimental study was conducted with the finest size fraction of nonferrous stream produced at an ELV shredder plant. The aim of this work was to characterize the nonferrous stream and to evaluate the efficiency of a gravity concentration process in separating light and heavy nonferrous metal particles that could be easily integrated in a ELV shredder plant (in this case study the separation explicitly addressed copper and aluminum separation). The characterization of a sample of the 0-10mm particle size fraction showed a mixture of nonferrous metals with a certain degree of impurity due to the present of contaminants such as plastics. The majority of the particles exhibited a wire shape, preventing an efficient separation of materials without prior fragmentation. The gravity concentration process selected for this study was the wet shaking table and three operating parameters of the equipment were manipulated. A full factorial design in combination with a central composite design was employed to model metals recovery. Two second order polynomial equations were successfully fitted to describe the process and predict the recovery of copper and aluminum in Cu concentrate under the conditions of the present study. The optimum conditions were determined to be 11.1° of inclination, 2.8L/min of feed water flow and 4.9L/min of wash water flow. All three final products of the wet shaking table had a content higher than 90% in relation to one of the metals, wherein a Cu concentrate product was obtained with a Cu content of 96%, and 78% of Cu recovery and 2% of Al recovery. Copyright © 2015 Elsevier Ltd. All rights reserved.

Stick-slip behavior of Indian gabbro as studied using a NIED large-scale biaxial friction apparatus

NASA Astrophysics Data System (ADS)

Togo, Tetsuhiro; Shimamoto, Toshihiko; Yamashita, Futoshi; Fukuyama, Eiichi; Mizoguchi, Kazuo; Urata, Yumi

2015-04-01

This paper reports stick-slip behaviors of Indian gabbro as studied using a new large-scale biaxial friction apparatus, built in the National Research Institute for Earth Science and Disaster Prevention (NIED), Tsukuba, Japan. The apparatus consists of the existing shaking table as the shear-loading device up to 3,600 kN, the main frame for holding two large rectangular prismatic specimens with a sliding area of 0.75 m2 and for applying normal stresses σ n up to 1.33 MPa, and a reaction force unit holding the stationary specimen to the ground. The shaking table can produce loading rates v up to 1.0 m/s, accelerations up to 9.4 m/s2, and displacements d up to 0.44 m, using four servocontrolled actuators. We report results from eight preliminary experiments conducted with room humidity on the same gabbro specimens at v = 0.1-100 mm/s and σ n = 0.66-1.33 MPa, and with d of about 0.39 m. The peak and steady-state friction coefficients were about 0.8 and 0.6, respectively, consistent with the Byerlee friction. The axial force drop or shear stress drop during an abrupt slip is linearly proportional to the amount of displacement, and the slope of this relationship determines the stiffness of the apparatus as 1.15 × 108 N/m or 153 MPa/m for the specimens we used. This low stiffness makes fault motion very unstable and the overshooting of shear stress to a negative value was recognized in some violent stick-slip events. An abrupt slip occurred in a constant rise time of 16-18 ms despite wide variation of the stress drop, and an average velocity during an abrupt slip is linearly proportional to the stress drop. The use of a large-scale shaking table has a great potential in increasing the slip rate and total displacement in biaxial friction experiments with large specimens.

An Earthquake Shake Map Routine with Low Cost Accelerometers: Preliminary Results

NASA Astrophysics Data System (ADS)

Alcik, H. A.; Tanircan, G.; Kaya, Y.

2015-12-01

Vast amounts of high quality strong motion data are indispensable inputs of the analyses in the field of geotechnical and earthquake engineering however, high cost of installation of the strong motion systems constitutes the biggest obstacle for worldwide dissemination. In recent years, MEMS based (micro-electro-mechanical systems) accelerometers have been used in seismological research-oriented studies as well as earthquake engineering oriented projects basically due to precision obtained in downsized instruments. In this research our primary goal is to ensure the usage of these low-cost instruments in the creation of shake-maps immediately after a strong earthquake. Second goal is to develop software that will automatically process the real-time data coming from the rapid response network and create shake-map. For those purposes, four MEMS sensors have been set up to deliver real-time data. Data transmission is done through 3G modems. A subroutine was coded in assembler language and embedded into the operating system of each instrument to create MiniSEED files with packages of 1-second instead of 512-byte packages.The Matlab-based software calculates the strong motion (SM) parameters at every second, and they are compared with the user-defined thresholds. A voting system embedded in the software captures the event if the total vote exceeds the threshold. The user interface of the software enables users to monitor the calculated SM parameters either in a table or in a graph (Figure 1). A small scale and affordable rapid response network is created using four MEMS sensors, and the functionality of the software has been tested and validated using shake table tests. The entire system is tested together with a reference sensor under real strong ground motion recordings as well as series of sine waves with varying amplitude and frequency. The successful realization of this software allowed us to set up a test network at Tekirdağ Province, the closest coastal point to the moderate size earthquake activities in the Marmara Sea, Turkey.

Stratification and segregation features of pulverized electronic waste in flowing film concentration.

PubMed

Vidyadhar, A; Chalavadi, G; Das, A

2013-03-30

Gravity separation of metals from plastics in pulverized e-waste using flowing film concentration in a shaking table was investigated. Over 51% rejection of plastics in a single stage operation was achieved under optimum conditions. The shaking table was shown to be suitable for processing ground PCBs. Pulverized e-waste containing 22% metals was enriched to around 40% metals in a single pass. Statistical models for the mass yield of metal-rich stream and its grade were developed by design of experiments. Optimization was carried out to maximize the mass yield at a target product grade and preferred operating regimes were established. Experiments were designed to prevent metal loss and over 95% recovery values were obtained under all conditions. Settling distances of metals and plastics were computed and shown to be good indicators of separation performance. Particle morphology and stratification in the troughs in between the riffles were shown to influence the separation significantly. Water flow-assisted motion of the plastics was captured and its role in determining the effectiveness of separation was described. The efficacy of tabling was well established for treating ground PCBs. The wet process was shown to be environment friendly and sustainable. It is also relatively cheap and has good potential for industrial application. However, rigorous cost estimates will be required before commercial application. Copyright © 2013 Elsevier Ltd. All rights reserved.

Oregon's forest products industry: 1988.

Treesearch

James O. Howard; Franklin R. Ward

1991-01-01

This report presents the findings of a survey of all primary forest products industries in Oregon for 1988. The survey included the following sectors: lumber; veneer and plywood; pulp and board; shake and shingle; export; and post, pole, and piling. Tables, presented by sector and for the industry as a whole, include characteristics of the industry, nature and flow of...

California's forest products industry: 1988.

Treesearch

James O. Howard; Franklln R. Ward

1991-01-01

This report presents the findings of a survey of all primary forest products industries in California for 1988. The survey included the following sectors: lumber; veneer and plywood; pulp and board; shake and shingle; export; and post, pole, and piling. Tables, presented by sector and for the industry as a whole, include characteristics of the industry, nature and flow...

Oregon's forest products industry: 1985.

Treesearch

James O. Howard; Franklin R. Ward

1988-01-01

This report presents the findings of a 100-percent survey of the primary forest products industry in Oregon for 1985. The survey included the following sectors: lumber; veneer and plywood; pulp and board; shake and shingle; export; and post, pole, and piling. Tables, presented by sector and for the industry as a whole, include characteristics of the industry, nature...

Oregon's forest products industry: 1992.

Treesearch

Franklin R. Ward

1995-01-01

This report presents the findings of a survey of primary forest products industries in. Oregon for 1992. The survey included the following sectors: lumber; veneer and plywood; pulp and board; shake and shingle; export; and post, pole, and piling. Tables, presented by sector and for the industry as a whole, include characteristics of the industry, nature and flow of...

Oregon's forest products industry: 1994.

Treesearch

Franklin R. Ward

1997-01-01

This report presents the findings of a survey of primary forest products industries in Oregon for 1994. The survey included the following sectors: lumber; veneer; pulp and board; shake and shingle; export; and post, pole, and piling. Tables, presented by sector and for the industry as a whole, include characteristics of the industry, nature and flow of logs consumed,...

Shake Test Results and Dynamic Calibration Efforts for the Large Rotor Test Apparatus

NASA Technical Reports Server (NTRS)

Russell, Carl R.

2014-01-01

Prior to the full-scale wind tunnel test of the UH-60A Airloads rotor, a shake test was completed on the Large Rotor Test Apparatus. The goal of the shake test was to characterize the oscillatory response of the test rig and provide a dynamic calibration of the balance to accurately measure vibratory hub loads. This paper provides a summary of the shake test results, including balance, shaft bending gauge, and accelerometer measurements. Sensitivity to hub mass and angle of attack were investigated during the shake test. Hub mass was found to have an important impact on the vibratory forces and moments measured at the balance, especially near the UH-60A 4/rev frequency. Comparisons were made between the accelerometer data and an existing finite-element model, showing agreement on mode shapes, but not on natural frequencies. Finally, the results of a simple dynamic calibration are presented, showing the effects of changes in hub mass. The results show that the shake test data can be used to correct in-plane loads measurements up to 10 Hz and normal loads up to 30 Hz.

Comparison of static and shake culture in the decolorization of textile dyes and dye effluents by Phanerochaete chrysoporium.

PubMed

Sani, R K; Azmi, W; Banerjee, U C

1998-01-01

Decolorization of several dyes (Red HE-8B, Malachite Green, Navy Blue HE-2R, Magenta, Crystal Violet) and an industrial effluent with growing cells of Phanerochaete chrysosporium in shake and static culture was demonstrated. All the dyes and the industrial effluent were decolorized to some extent with varying percentages of decolorization (20-100%). The rate of decolorization was very rapid with Red HE-8B, an industrial dye. Decolorization rates for all the dyes in static condition were found to be less than the shake culture and also dependent on biomass concentration.

Shaking Table Experiment of Trampoline Effect

NASA Astrophysics Data System (ADS)

Aoi, S.; Kunugi, T.; Fujiwara, H.

2010-12-01

It has been widely thought that soil response to ground shaking do not experience asymmetry in ground motion. An extreme vertical acceleration near four times gravity was recorded during the 2008 Iwate-Miyagi earthquake at IWTH25 station. This record is distinctly asymmetric in shape; the waveform envelope amplitude is about 1.6 times larger in the upward direction compared to the downward direction. To explain this phenomenon, Aoi et al. (2008) proposed a simple model of a mass bouncing on a trampoline. In this study we perform a shaking table experiment of a soil prototype to try to reproduce the asymmetric ground motion and to investigate the physics of this asymmetric behavior. A soil chamber made of an acrylic resin cylinder with 200 mm in diameter and 500 mm in height was tightly anchored to the shaking table and vertically shaken. We used four different sample materials; Toyoura standard sands, grass beads (particle size of 0.1 and 0.4 mm) and sawdust. Sample was uniformly stacked to a depth of 450 mm and, to measure the vertical motions, accelerometers was installed inside the material (at depths of 50, 220, and 390 mm) and on the frame of the chamber. Pictures were taken from a side by a high speed camera (1000 frames/sec) to capture the motions of particles. The chamber was shaken by sinusoidal wave (5, 10, and 20 Hz) with maximum amplitudes from 0.1 to 4.0 g. When the accelerations roughly exceeded gravity, for all samples, granular behaviors of sample materials became dominant and the asymmetric motions were successfully reproduced. Pictures taken by the high speed camera showed that the motions of the particles are clearly different from the motion of the chamber which is identical to the sinusoidal motion of the shaking table (input motion). Particles are rapidly flung up and freely pulled down by gravity, and the downward motion of the particles is slower than the upward motion. It was also observed that the timing difference of the falling motions indicate a dependence with depth. Our results show that the shape of time histories of recorded motions by the accelerometers within the sample, becomes increasingly different than the input sinusoidal wave for sensors at shallower depths. When sands or grass beads are used as fill material, the observed waveforms under large accelerations are the summation of a warped sine-like function and one or few sharp pulses, which might be caused by the shocks generated by the 'landing' of the free-falling material. For sawdust, the observed waveforms have much more smooth shapes which are also asymmetric; larger and narrower for upward direction and smaller and broader for downward direction. The reason why the waveforms of the sawdust experiments are different from the sand or grass bead cases is mainly due to the different elastic deformation characteristics of each material. The impacts of the 'landing' are reduced by the resilience of the sawdust and the shape pulses become blunt. Our experiments show that within all tested materials the sawdust is the one that somehow reproduces waveforms with the largest similarities to the observed asymmetric waveform at IWTH25. This shows that both the granularity and the elasticity may play an important role when the vertical ground motions become asymmetric.

Analysis on Two Typical Landslide Hazard Phenomena in The Wenchuan Earthquake by Field Investigations and Shaking Table Tests.

PubMed

Yang, Changwei; Zhang, Jianjing; Liu, Feicheng; Bi, Junwei; Jun, Zhang

2015-08-06

Based on our field investigations of landslide hazards in the Wenchuan earthquake, some findings can be reported: (1) the multi-aspect terrain facing empty isolated mountains and thin ridges reacted intensely to the earthquake and was seriously damaged; (2) the slope angles of most landslides was larger than 45°. Considering the above disaster phenomena, the reasons are analyzed based on shaking table tests of one-sided, two-sided and four-sided slopes. The analysis results show that: (1) the amplifications of the peak accelerations of four-sided slopes is stronger than that of the two-sided slopes, while that of the one-sided slope is the weakest, which can indirectly explain the phenomena that the damage is most serious; (2) the amplifications of the peak accelerations gradually increase as the slope angles increase, and there are two inflection points which are the point where the slope angle is 45° and where the slope angle is 50°, respectively, which can explain the seismic phenomenon whereby landslide hazards mainly occur on the slopes whose slope angle is bigger than 45°. The amplification along the slope strike direction is basically consistent, and the step is smooth.

Study on soil-pile-structure-TMD interaction system by shaking table model test

NASA Astrophysics Data System (ADS)

Lou, Menglin; Wang, Wenjian

2004-06-01

The success of the tuned mass damper (TMD) in reducing wind-induced structural vibrations has been well established. However, from most of the recent numerical studies, it appears that for a structure situated on very soft soil, soil-structure interaction (SSI) could render a damper on the structure totally ineffective. In order to experimentally verify the SSI effect on the seismic performance of TMD, a series of shaking table model tests have been conducted and the results are presented in this paper. It has been shown that the TMD is not as effective in controlling the seismic responses of structures built on soft soil sites due to the SSI effect. Some test results also show that a TMD device might have a negative impact if the SSI effect is neglected and the structure is built on a soft soil site. For structures constructed on a soil foundation, this research verifies that the SSI effect must be carefully understood before a TMD control system is designed to determine if the control is necessary and if the SSI effect must be considered when choosing the optimal parameters of the TMD device.

Monitoring of Engineering Buildings Behaviour Within the Disaster Management System

NASA Astrophysics Data System (ADS)

Oku Topal, G.; Gülal, E.

2017-11-01

The Disaster management aims to prevent events that result in disaster or to reduce their losses. Monitoring of engineering buildings, identification of unusual movements and taking the necessary precautions are very crucial for determination of the disaster risk so possible prevention could be taken to reduce big loss. Improving technology, increasing population due to increased construction and these areas largest economy lead to offer damage detection strategies. Structural Health Monitoring (SHM) is the most effective of these strategies. SHM research is very important to maintain all this structuring safely. The purpose of structural monitoring is determining in advance of possible accidents and taking necessary precaution. In this paper, determining the behaviour of construction using Global Positioning System (GPS) is investigated. For this purpose shaking table tests were performed. Shaking table was moved at different amplitude and frequency aiming to determine these movement with a GPS measuring system. The obtained data were evaluated by analysis of time series and Fast Fourier Transformation techniques and the frequency and amplitude values are calculated. By examining the results of the tests made, it will be determined whether the GPS measurement method can accurately detect the movements of the engineering structures.

GNSS seismometer: Seismic phase recognition of real-time high-rate GNSS deformation waves

NASA Astrophysics Data System (ADS)

Nie, Zhaosheng; Zhang, Rui; Liu, Gang; Jia, Zhige; Wang, Dijin; Zhou, Yu; Lin, Mu

2016-12-01

High-rate global navigation satellite systems (GNSS) can potentially be used as seismometers to capture short-period instantaneous dynamic deformation waves from earthquakes. However, the performance and seismic phase recognition of the GNSS seismometer in the real-time mode, which plays an important role in GNSS seismology, are still uncertain. By comparing the results of accuracy and precision of the real-time solution using a shake table test, we found real-time solutions to be consistent with post-processing solutions and independent of sampling rate. In addition, we analyzed the time series of real-time solutions for shake table tests and recent large earthquakes. The results demonstrated that high-rate GNSS have the ability to retrieve most types of seismic waves, including P-, S-, Love, and Rayleigh waves. The main factor limiting its performance in recording seismic phases is the widely used 1-Hz sampling rate. The noise floor also makes recognition of some weak seismic phases difficult. We concluded that the propagation velocities and path of seismic waves, macro characteristics of the high-rate GNSS array, spatial traces of seismic phases, and incorporation of seismographs are all useful in helping to retrieve seismic phases from the high-rate GNSS time series.

Determination of cadmium and lead in table salt by sequential multi-element flame atomic absorption spectrometry.

PubMed

Amorim, Fábio A C; Ferreira, Sérgio L C

2005-02-28

In the present paper, a simultaneous pre-concentration procedure for the sequential determination of cadmium and lead in table salt samples using flame atomic absorption spectrometry is proposed. This method is based on the liquid-liquid extraction of cadmium(II) and lead(II) ions as dithizone complexes and direct aspiration of the organic phase for the spectrometer. The sequential determination of cadmium and lead is possible using a computer program. The optimization step was performed by a two-level fractional factorial design involving the variables: pH, dithizone mass, shaking time after addition of dithizone and shaking time after addition of solvent. In the studied levels these variables are not significant. The experimental conditions established propose a sample volume of 250mL and the extraction process using 4.0mL of methyl isobutyl ketone. This way, the procedure allows determination of cadmium and lead in table salt samples with a pre-concentration factor higher than 80, and detection limits of 0.3ngg(-1) for cadmium and 4.2ngg(-1) for lead. The precision expressed as relative standard deviation (n = 10) were 5.6 and 2.6% for cadmium concentration of 2 and 20ngg(-1), respectively, and of 3.2 and 1.1% for lead concentration of 20 and 200ngg(-1), respectively. Recoveries of cadmium and lead in several samples, measured by standard addition technique, proved also that this procedure is not affected by the matrix and can be applied satisfactorily for the determination of cadmium and lead in saline samples. The method was applied for the evaluation of the concentration of cadmium and lead in table salt samples consumed in Salvador City, Bahia, Brazil.

High-resolution flying-PIV with optical fiber laser delivery

NASA Astrophysics Data System (ADS)

Weichselbaum, Noah A.; André, Matthieu A.; Rahimi-Abkenar, Morteza; Manzari, Majid T.; Bardet, Philippe M.

2016-05-01

Implementation of non-intrusive optical measurement techniques, such as particle image velocimetry (PIV), in harsh environments requires specialized techniques for introducing controlled laser sheets to the region of interest. Large earthquake shake tables are a particularly challenging environment. Lasers must be mounted away from the table, and the laser sheet has to be delivered precisely and stably to the measurement station. Here, high-power multi-mode step-index fiber optics enable introduction of light from an Nd:YLF pulsed laser to a remote test section. Such lasers are suitable for coupling to optical fibers, which presents a portable, flexible, and safe manner to deliver a PIV light sheet. Best practices for their implementation are reviewed. Particular attention is focused on obtaining a collimated beam of acceptable quality at the output of the fiber. To achieve high spatial resolution, the PIV camera is directly mounted on the moving shake table with care to minimize its vibrations. A special arrangement of PIV planes is deployed for precise in-situ PIV alignment and to monitor and account for residual structure vibrations and beam wandering. The design of the instruments is detailed. Here, an experimental facility for the study of nuclear fuel bundle response to seismic forcing near prototypical conditions is instrumented. Only through integration of a high-resolution flying-PIV system can velocity fields be acquired. Data indicate that in the presence of a mean axial flow, a secondary oscillatory flow develops as the bundle oscillates. Instantaneous, phase-averaged, and fluctuating velocity fields illustrate this phenomenon.

Ground shake test of the UH-60A helicopter airframe and comparison with NASTRAN finite element model predictions

NASA Technical Reports Server (NTRS)

Howland, G. R.; Durno, J. A.; Twomey, W. J.

1990-01-01

Sikorsky Aircraft, together with the other major helicopter airframe manufacturers, is engaged in a study to improve the use of finite element analysis to predict the dynamic behavior of helicopter airframes, under a rotorcraft structural dynamics program called DAMVIBS (Design Analysis Methods for VIBrationS), sponsored by the NASA-Langley. The test plan and test results are presented for a shake test of the UH-60A BLACK HAWK helicopter. A comparison is also presented of test results with results obtained from analysis using a NASTRAN finite element model.

An atlas of ShakeMaps for selected global earthquakes

USGS Publications Warehouse

Allen, Trevor I.; Wald, David J.; Hotovec, Alicia J.; Lin, Kuo-Wan; Earle, Paul S.; Marano, Kristin D.

2008-01-01

An atlas of maps of peak ground motions and intensity 'ShakeMaps' has been developed for almost 5,000 recent and historical global earthquakes. These maps are produced using established ShakeMap methodology (Wald and others, 1999c; Wald and others, 2005) and constraints from macroseismic intensity data, instrumental ground motions, regional topographically-based site amplifications, and published earthquake-rupture models. Applying the ShakeMap methodology allows a consistent approach to combine point observations with ground-motion predictions to produce descriptions of peak ground motions and intensity for each event. We also calculate an estimated ground-motion uncertainty grid for each earthquake. The Atlas of ShakeMaps provides a consistent and quantitative description of the distribution and intensity of shaking for recent global earthquakes (1973-2007) as well as selected historic events. As such, the Atlas was developed specifically for calibrating global earthquake loss estimation methodologies to be used in the U.S. Geological Survey Prompt Assessment of Global Earthquakes for Response (PAGER) Project. PAGER will employ these loss models to rapidly estimate the impact of global earthquakes as part of the USGS National Earthquake Information Center's earthquake-response protocol. The development of the Atlas of ShakeMaps has also led to several key improvements to the Global ShakeMap system. The key upgrades include: addition of uncertainties in the ground motion mapping, introduction of modern ground-motion prediction equations, improved estimates of global seismic-site conditions (VS30), and improved definition of stable continental region polygons. Finally, we have merged all of the ShakeMaps in the Atlas to provide a global perspective of earthquake ground shaking for the past 35 years, allowing comparison with probabilistic hazard maps. The online Atlas and supporting databases can be found at http://earthquake.usgs.gov/eqcenter/shakemap/atlas.php/.

Mobile Phones and Social Media Empower the Citizen Seismologist

NASA Astrophysics Data System (ADS)

Bray, J.; Dashti, S.; Reilly, J.; Bayen, A. M.; Glaser, S. D.

2014-12-01

Emergency responders must "see" the effects of an earthquake clearly and rapidly for effective response. Mobile phone and information technology can be used to measure ground motion intensity parameters and relay that information to emergency responders. However, the phone sensor is an imperfect device and has a limited operational range. Thus, shake table tests were performed to evaluate their reliability as seismic monitoring instruments. Representative handheld devices, either rigidly connected to the table or free to move, measured shaking intensity parameters well. Bias in 5%-damped spectral accelerations measured by phones was less than 0.05 and 0.2 [log(g)] during one-dimensional (1-D) and three-dimensional (3-D) shaking in frequencies ranging from 1 Hz to 10 Hz. They did tend to over-estimate the Arias Intensity, but this error declined for stronger motions with larger signal-to-noise ratios. Additionally, much of the data about infrastructure performance and geotechnical effects of an earthquake are lost soon after an earthquake occurs as efforts move to the recovery phase. A better methodology for reliable and rapid collection of perishable hazards data will enhance scientific inquiry and accelerate the building of disaster-resilient cities. Post-earthquake reconnaissance efforts can be aided through the strategic collection and reuse of social media data and other remote sources of information. This is demonstrated through their use following the NSF-sponsored GEER response to the September 2013 flooding in Colorado. With these ubiquitous measurement devices in the hands of the citizen seismologist, a more accurate and rapid portrayal of the damage distribution during an earthquake may be provided to emergency responders and to the public.

ARC-2007-ACD07-0073-047

NASA Image and Video Library

2007-04-14

Lunar CRater Observation and Sensing Satellite (LCROSS) and P.I. at NASA Ames Research Center - close up of Total Luminance Photometer: Metal shake table close up. Shows two units bolted on. The left one is the lens, sensor electronics and photometer sensor. The right is the digital electronics unit for the instrument. The two units, along with their cabling is one of the LCROSS science insruments.

Mass timber rocking panel retrofit of a four-story soft-story building with full-scale shake table validation

Treesearch

Pouria Bahmani; John van de Lindt; Asif Iqbal; Douglas Rammer

2017-01-01

Soft-story wood-frame buildings have been recognized as a disaster preparedness problem for decades. There are tens of thousands of these multi-family three- and four-story structures throughout California and the United States. The majority were constructed between 1920 and 1970, with many being prevalent in the San Francisco Bay Area in California. The NEES Soft...

EXPERIMENTAL STUDY ON BEHAVIOR OF KENCHI BLOCK MASONRY WALL WITH THE SHAKING TABLE TEST DURING BY VIBRATION CHARACTERISTICS AND FAILURE MECHANISM

NASA Astrophysics Data System (ADS)

Ikemoto, Toshikazu; Mori, Masashi; Miyajima, Masakatsu; Hashimoto, Takao; Murata, Akira

There are many earthquake damages of kenchi block masonry wall. So, we carried out experimental studies on the collapse mechanism of kenchi block masonry wall during earthquake. From these experimental data, i.e. acceleration response magnification, displacement and soil pressure were found to destroy the central wall vibrations caused by the subsidence of the embankment.

Analysis on Two Typical Landslide Hazard Phenomena in The Wenchuan Earthquake by Field Investigations and Shaking Table Tests

PubMed Central

Yang, Changwei; Zhang, Jianjing; Liu, Feicheng; Bi, Junwei; Jun, Zhang

2015-01-01

Based on our field investigations of landslide hazards in the Wenchuan earthquake, some findings can be reported: (1) the multi-aspect terrain facing empty isolated mountains and thin ridges reacted intensely to the earthquake and was seriously damaged; (2) the slope angles of most landslides was larger than 45°. Considering the above disaster phenomena, the reasons are analyzed based on shaking table tests of one-sided, two-sided and four-sided slopes. The analysis results show that: (1) the amplifications of the peak accelerations of four-sided slopes is stronger than that of the two-sided slopes, while that of the one-sided slope is the weakest, which can indirectly explain the phenomena that the damage is most serious; (2) the amplifications of the peak accelerations gradually increase as the slope angles increase, and there are two inflection points which are the point where the slope angle is 45° and where the slope angle is 50°, respectively, which can explain the seismic phenomenon whereby landslide hazards mainly occur on the slopes whose slope angle is bigger than 45°. The amplification along the slope strike direction is basically consistent, and the step is smooth. PMID:26258785

Experimental and numerical investigations of higher mode effects on seismic inelastic response of reinforced concrete shear walls

NASA Astrophysics Data System (ADS)

Ghorbanirenani, Iman

This thesis presents two experimental programs together with companion numerical studies that were carried out on reinforced concrete shear walls: static tests and dynamic (shake table) tests. The first series of experiments were monotonic and cyclic quasi-static testing on ductile reinforced concrete shear wall specimens designed and detailed according to the seismic provisions of NBCC 2005 and CSA-A23.3-04 standard. The tests were carried out on full-scale and 1:2.37 reduced scale wall specimens to evaluate the seismic design provisions and similitude law and determine the appropriate scaling factor that could be applied for further studies such as dynamic tests. The second series of experiments were shake table tests conducted on two identical 1:2.33 scaled, 8-storey moderately ductile reinforced concrete shear wall specimens to investigate the effects of higher modes on the inelastic response of slender walls under high frequency ground motions expected in Eastern North America. The walls were designed and detailed according to the seismic provisions of NBCC 2005 and CSA-A23.3-04 standard. The objectives were to validate and understand the inelastic response and interaction of shear, flexure and axial loads in plastic hinge zones of the walls considering the higher mode effects and to investigate the formation of second hinge in upper part of the wall due to higher mode responses. Second mode response significantly affected the response of the walls. This caused inelastic flexural response to develop at the 6th level with approximately the same rotation ductility compared to that observed at the base. Dynamic amplification of the base shear forces was also observed in both walls. Numerical modeling of these two shake table tests was performed to evaluate the test results and validate current modeling approaches. Nonlinear time history analyses were carried out by the reinforced concrete fibre element (OpenSees program) and finite element (VecTor2 program) methods using the shake table feedback signals as input. Good agreement was generally obtained between numerical and experimental results. Both computer programs were able to predict the natural frequency of the walls in the undamaged and damaged conditions. Both modeling techniques could predict that the maximum bending moment at the base of the walls reached the actual wall moment capacity. The inelastic response and the dual plastic hinge behaviour of the walls could be adequately reproduced using the fibre element and finite element analysis programs. The fibre element method is a good alternative in terms of computing time. It produces reasonable results in comparison with the finite element method, although particular attention needs to be given to the selection of the damping ratios. The different parametric analyses performed in this thesis showed that, for both models, adding a small amount of global viscous damping in combination with a refined reinforced concrete hysteretic model could predict better the seismic behaviour of the tested structures. For the VecTor2 program, a viscous damping of 1% led to reasonable results for the studied RC walls. For the OpenSees program, 2% damping resulted in a good match between test and predictions for the 100% EQ test on the initially undamaged wall. When increasing the earthquake intensities, the damping had to be reduced between 1.5% and 1% to achieve good results for a damaged wall with elongated vibration periods. According to the experimental results and numerical analyses on reinforced concrete shear walls subjected to ground motions from Eastern North America earthquakes, there is a high possibility of having a second plastic hinge forming in the upper part of walls in addition to the one assumed in design at the base. This second hinge could dissipate the earthquake energy more effectively and decrease the force demand on the wall. A dual plastic hinge design approach in which the structures become plastic in the upper wall segment as well as the base could be therefore more appropriate. Preliminary design recommendations considering higher mode effects on dual hinge response and base shear forces for ductile slender shear walls are given in this thesis. (Abstract shortened by UMI.)

CENTRIFUGAL VIBRATION TEST OF RC PILE FOUNDATION

NASA Astrophysics Data System (ADS)

Higuchi, Shunichi; Tsutsumiuchi, Takahiro; Otsuka, Rinna; Ito, Koji; Ejiri, Joji

It is necessary that nonlinear responses of structures are clarified by soil-structure interaction analysis for the purpose of evaluating the seismic performances of underground structure or foundation structure. In this research, centrifuge shake table tests of reinforced concrete pile foundation installed in the liquefied ground were conducted. Then, finite element analyses for the tests were conducted to confirm an applicability of the analytical method by comparing the experimental results and analytical results.

Experimental seismic behavior of a full-scale four-story soft-story wood-frame building with retrofits II: shake table test results

Treesearch

John W. van de Lindt; Pouria Bahmani; Gary Mochizuki; Steven E. Pryor; Mikhail Gershfeld; Jingjing Tian; Michael D. Symans; Douglas Rammer

2016-01-01

Soft-story wood-frame buildings have been recognized as a disaster preparedness problem for decades. The majority of these buildings were constructed from the 1920s to the 1960s and are prone to collapse during moderate to large earthquakes due to a characteristic deficiency in strength and stiffness in their first story. In order to propose and validate retrofit...

Experimental study on control performance of tuned liquid column dampers considering different excitation directions

NASA Astrophysics Data System (ADS)

Altunişik, Ahmet Can; Yetişken, Ali; Kahya, Volkan

2018-03-01

This paper gives experimental tests' results for the control performance of Tuned Liquid Column Dampers (TLCDs) installed on a prototype structure exposed to ground motions with different directions. The prototype structure designed in the laboratory consists of top and bottom plates with four columns. Finite element analyses and ambient vibration tests are first performed to extract the natural frequencies and mode shapes of the structure. Then, the damping ratio of the structure as well as the resonant frequency, head-loss coefficient, damping ratio, and water height-frequency diagram of the designed TLCD are obtained experimentally by the shaking table tests. To investigate the effect of TLCDs on the structural response, the prototype structure-TLCD coupled system is considered later, and its natural frequencies and related mode shapes are obtained numerically. The acceleration and displacement time-histories are obtained by the shaking table tests to evaluate its damping ratio. To consider different excitation directions, the measurements are repeated for the directions between 0° and 90° with 15° increment. It can be concluded from the study that TLCD causes to decrease the resonant frequency of the structure with increasing of the total mass. Damping ratio considerably increases with installing TLCD on the structure. This is more pronounced for the angles of 0°, 15°, 30° and 45°.

Seismic isolation of small modular reactors using metamaterials

NASA Astrophysics Data System (ADS)

Witarto, Witarto; Wang, S. J.; Yang, C. Y.; Nie, Xin; Mo, Y. L.; Chang, K. C.; Tang, Yu; Kassawara, Robert

2018-04-01

Adaptation of metamaterials at micro- to nanometer scales to metastructures at much larger scales offers a new alternative for seismic isolation systems. These new isolation systems, known as periodic foundations, function both as a structural foundation to support gravitational weight of the superstructure and also as a seismic isolator to isolate the superstructure from incoming seismic waves. Here we describe the application of periodic foundations for the seismic protection of nuclear power plants, in particular small modular reactors (SMR). For this purpose, a large-scale shake table test on a one-dimensional (1D) periodic foundation supporting an SMR building model was conducted. The 1D periodic foundation was designed and fabricated using reinforced concrete and synthetic rubber (polyurethane) materials. The 1D periodic foundation structural system was tested under various input waves, which include white noise, stepped sine and seismic waves in the horizontal and vertical directions as well as in the torsional mode. The shake table test results show that the 1D periodic foundation can reduce the acceleration response (transmissibility) of the SMR building up to 90%. In addition, the periodic foundation-isolated structure also exhibited smaller displacement than the non-isolated SMR building. This study indicates that the challenge faced in developing metastructures can be overcome and the periodic foundations can be applied to isolating vibration response of engineering structures.

Mathematical modeling and full-scale shaking table tests for multi-curve buckling restrained braces

NASA Astrophysics Data System (ADS)

Tsai, C. S.; Lin, Yungchang; Chen, Wenshin; Su, H. C.

2009-09-01

Buckling restrained braces (BRBs) have been widely applied in seismic mitigation since they were introduced in the 1970s. However, traditional BRBs have several disadvantages caused by using a steel tube to envelope the mortar to prevent the core plate from buckling, such as: complex interfaces between the materials used, uncertain precision, and time consumption during the manufacturing processes. In this study, a new device called the multi-curve buckling restrained brace (MC-BRB) is proposed to overcome these disadvantages. The new device consists of a core plate with multiple neck portions assembled to form multiple energy dissipation segments, and the enlarged segment, lateral support elements and constraining elements to prevent the BRB from buckling. The enlarged segment located in the middle of the core plate can be welded to the lateral support and constraining elements to increase buckling resistance and to prevent them from sliding during earthquakes. Component tests and a series of shaking table tests on a full-scale steel structure equipped with MC-BRBs were carried out to investigate the behavior and capability of this new BRB design for seismic mitigation. The experimental results illustrate that the MC-BRB possesses a stable mechanical behavior under cyclic loadings and provides good protection to structures during earthquakes. Also, a mathematical model has been developed to simulate the mechanical characteristics of BRBs.

Faecal indicator bacteria enumeration in beach sand: a comparison study of extraction methods in medium to coarse sands.

PubMed

Boehm, A B; Griffith, J; McGee, C; Edge, T A; Solo-Gabriele, H M; Whitman, R; Cao, Y; Getrich, M; Jay, J A; Ferguson, D; Goodwin, K D; Lee, C M; Madison, M; Weisberg, S B

2009-11-01

The absence of standardized methods for quantifying faecal indicator bacteria (FIB) in sand hinders comparison of results across studies. The purpose of the study was to compare methods for extraction of faecal bacteria from sands and recommend a standardized extraction technique. Twenty-two methods of extracting enterococci and Escherichia coli from sand were evaluated, including multiple permutations of hand shaking, mechanical shaking, blending, sonication, number of rinses, settling time, eluant-to-sand ratio, eluant composition, prefiltration and type of decantation. Tests were performed on sands from California, Florida and Lake Michigan. Most extraction parameters did not significantly affect bacterial enumeration. anova revealed significant effects of eluant composition and blending; with both sodium metaphosphate buffer and blending producing reduced counts. The simplest extraction method that produced the highest FIB recoveries consisted of 2 min of hand shaking in phosphate-buffered saline or deionized water, a 30-s settling time, one-rinse step and a 10 : 1 eluant volume to sand weight ratio. This result was consistent across the sand compositions tested in this study but could vary for other sand types. Method standardization will improve the understanding of how sands affect surface water quality.

Test of FBG sensors for monitoring high pressure pipes

NASA Astrophysics Data System (ADS)

Paolozzi, Antonio; Paris, Claudio; Vendittozzi, Cristian; Felli, Ferdinando; Mongelli, Marialuisa; De Canio, Gerardo; Colucci, Alessandro; Asanuma, Hiroshi

2017-04-01

Fibre Bragg Grating (FBG) sensors are increasingly being used on a wide range of civil, industrial and aerospace structures. The sensors are created inside optical fibres (usually standard telecommunication fibres); the optical fibres technology allows to install the sensors on structures working in harsh environments, since the materials are almost insensitive to corrosion, the monitoring system can be positioned far away from the sensors without sensible signal losses, and there is no risk of electric discharge. FBG sensors can be used to create strain gages, thermometers or accelerometers, depending on the coating on the grating, on the way the grating is fixed to the structure, and on the presence of a specifically designed interface that can act as a transducer. This paper describes a test of several different FBG sensors to monitor an high pressure pipe that feeds the hydraulic actuators of a 6 degrees-of-freedom shaking table at the ENEA Casaccia research centre. A bare FBG sensor and a copper coated FBG sensor have been glued on the pipe. A third sensor has been mounted on a special interface to amplify the vibrations; this last sensor can be placed on the steel pipe by a magnetic mounting system, that also allows the its removal. All the sensor are placed parallel to the axis of the pipe. The analysis of the data recorded when the shaking table is operated will allow to determine which kind of sensor is best suited for structural monitoring of high pressure pipelines.

Improving Drive Files for Vehicle Road Simulations

NASA Astrophysics Data System (ADS)

Cherng, John G.; Goktan, Ali; French, Mark; Gu, Yi; Jacob, Anil

2001-09-01

Shaker tables are commonly used in laboratories for automotive vehicle component testing to study durability and acoustics performance. An example is development testing of car seats. However, it is difficult to repeat the measured road data perfectly with the response of a shaker table as there are basic differences in dynamic characteristics between a flexible vehicle and substantially rigid shaker table. In addition, there are performance limits in the shaker table drive systems that can limit correlation. In practice, an optimal drive signal for the actuators is created iteratively. During each iteration, the error between the road data and the response data is minimised by an optimising algorithm which is generally a part of the feed back loop of the shake table controller. This study presents a systematic investigation to the errors in time and frequency domains as well as joint time-frequency domain and an evaluation of different digital signal processing techniques that have been used in previous work. In addition, we present an innovative approach that integrates the dynamic characteristics of car seats and the human body into the error-minimising iteration process. We found that the iteration process can be shortened and the error reduced by using a weighting function created by normalising the frequency response function of the car seat. Two road data test sets were used in the study.

Use of saline waste water from demineralization of cheese whey for cultivation of Schizochytrium limacinum PA-968 and Japonochytrium marinum AN-4.

PubMed

Humhal, Tomas; Kastanek, Petr; Jezkova, Zuzana; Cadkova, Anna; Kohoutkova, Jana; Branyik, Tomas

2017-03-01

Saline waste water from demineralization of cheese whey was used as the main component of waste saline medium (WSM) for cultivation of thraustochytrids. The suitability of WSM for cultivation of Schizochytrium limacinum PA-968 and Japonochytrium marinum AN-4 was evaluated by comparison with cultivation on nutrient medium (NM) in shake flask and fermenter cultures. Biomass productivities achieved in WSM for the thraustochytrids were comparable with those in NM for both shake flask and fermenter cultures. The maximum total lipid content (56.71% dry cell weight) and docosahexaenoic acid productivity (0.86 g/L/day) were achieved by J. marinum AN-4 grown on WSM in shake flask and fermenter cultures, respectively. A cost estimate of WSM suggests that this medium could result in lower production costs for thraustochytrid biomass and lipids and contribute to the effective reduction in saline diary process waste water.

Use of Solid Waste (Foundry Slag) Mortar and Bamboo Reinforcement in Seismic Analysis for Single Storey Masonry Building

NASA Astrophysics Data System (ADS)

Ahmad, S.; Husain, A.; Ghani, F.; Alam, M. N.

2013-11-01

The conversion of large amount of solid waste (foundry slag) into alternate source of building material will contribute not only as a solution to growing waste problem, but also it will conserve the natural resources of other building material and thereby reduce the cost of construction. The present work makes an effort to safe and economic use of recycle mortar (1:6) as a supplementary material. Conventional and recycled twelve prisms were casted with varying percentage of solid waste (foundry slag) added (0, 10, 20, 30 %) replacing cement by weight and tested under compression testing machine. As the replacement is increasing, the strength is decreasing. 10 % replacement curve is very closed to 0 % whereas 20 % is farther and 30 % is farthest. 20 % replacement was chosen for dynamic testing as its strength is within permissible limit as per IS code. A 1:4 scale single storey brick model with half size brick was fabricated on shake table in the lab for dynamic testing using pure friction isolation system (coarse sand as friction material µ = 0.34). Pure friction isolation technique can be adopted economically in developing countries where low-rise building prevails due to their low cost. The superstructure was separated from the foundation at plinth level, so as to permit sliding of superstructure during severe earthquake. The observed values of acceleration and displacement responses compare fairly with the analytical values of the analytical model. It also concluded that 20 % replacement of cement by solid waste (foundry slag) could be safely adopted without endangering the safety of the masonry structures under seismic load.To have an idea that how much energy is dissipated through this isolation, the same model with fixed base was tested and results were compared with the isolated free sliding model and it has been observed that more than 60 % energy is dissipated through this pure friction isolation technique. In case of base isolation, no visible cracks were observed up to the table force of 4.25 kN (1,300 rpm), whereas for fixed base failure started at 800 rpm.To strengthen the fixed base model, bamboo reinforcement were used for economical point of view. Another model of same dimension with same mortar ratio was fabricated on the shake table with bamboo reinforcement as plinth band and lintel band. In addition another four round bamboo bars of 3 mm diameter were placed at each of the four corners of the model. The building model was tested and found very encouraging and surprising results. The model failure started at 1,600 rpm, which means that this model is surviving the double force in comparison with the non-bamboo reinforcement.

A/E/C Graphics Standard: Release 2.0 (formerly titled CAD Drafting Standard)

DTIC Science & Technology

2015-08-01

Tables Table 2-1. ANSI and ISO sheet size comparison . ....................................................................................... 3... Comparison of font types. ......................................................................................................... 45 Table 5-2. Inch...used (ISO A0 may be used for large maps). Table 2-1 lists the standard sizes of ANSI and ISO sheets. Table 2-1. ANSI and ISO sheet size comparison

Faecal indicator bacteria enumeration in beach sand: A comparison study of extraction methods in medium to coarse sands

USGS Publications Warehouse

Boehm, A.B.; Griffith, J.; McGee, C.; Edge, T.A.; Solo-Gabriele, H. M.; Whitman, R.; Cao, Y.; Getrich, M.; Jay, J.A.; Ferguson, D.; Goodwin, K.D.; Lee, C.M.; Madison, M.; Weisberg, S.B.

2009-01-01

Aims: The absence of standardized methods for quantifying faecal indicator bacteria (FIB) in sand hinders comparison of results across studies. The purpose of the study was to compare methods for extraction of faecal bacteria from sands and recommend a standardized extraction technique. Methods and Results: Twenty-two methods of extracting enterococci and Escherichia coli from sand were evaluated, including multiple permutations of hand shaking, mechanical shaking, blending, sonication, number of rinses, settling time, eluant-to-sand ratio, eluant composition, prefiltration and type of decantation. Tests were performed on sands from California, Florida and Lake Michigan. Most extraction parameters did not significantly affect bacterial enumeration. anova revealed significant effects of eluant composition and blending; with both sodium metaphosphate buffer and blending producing reduced counts. Conclusions: The simplest extraction method that produced the highest FIB recoveries consisted of 2 min of hand shaking in phosphate-buffered saline or deionized water, a 30-s settling time, one-rinse step and a 10 : 1 eluant volume to sand weight ratio. This result was consistent across the sand compositions tested in this study but could vary for other sand types. Significance and Impact of the Study: Method standardization will improve the understanding of how sands affect surface water quality. ?? 2009 The Society for Applied Microbiology.

Determination of Ultramicro Quantities of Elemental Phosphorus in Water by Neutron Activation Analysis.

DTIC Science & Technology

1977-06-10

HYPOPHOSPHITE :80x I0O4 PHOSPHITE I1.8 x 10- PHOSPHATE 8.0 x 1- SODIUM SALTS: 10 mg/I 16 mad NSWC/WOL TR 77-49 TABLE 3 RECOVERY OF PHOSPHORUS IN NITRIC ACID...of the benzene extract by shaking with aqueous nitric acid resulted in nitric acid oxidation of P4 to phosphate ion. which then nassed into the...aqueous phase. The treatment was carrie out in a mechanical shaker or magnetic stirrer. The aqueous layer, containing phosphate , was isolated in a

iShake: Mobile Phones as Seismic Sensors (Invited)

NASA Astrophysics Data System (ADS)

Dashti, S.; Reilly, J.; Bray, J. D.; Bayen, A. M.; Glaser, S. D.; Mari, E.

2010-12-01

Emergency responders must “see” the effects of an earthquake clearly and rapidly so that they can respond effectively to the damage it has produced. Great strides have been made recently in developing methodologies that deliver rapid and accurate post-earthquake information. However, shortcomings still exist. The iShake project is an innovative use of cell phones and information technology to bridge the gap between the high quality, but sparse, ground motion instrument data that are used to help develop ShakeMap and the low quality, but large quantity, human observational data collected to construct a “Did You Feel It?” (DYFI)-based map. Rather than using people as measurement “devices” as is being done through DYFI, the iShake project is using their cell phones to measure ground motion intensity parameters and automatically deliver the data to the U.S. Geological Survey (USGS) for processing and dissemination. In this participatory sensing paradigm, quantitative shaking data from numerous cellular phones will enable the USGS to produce shaking intensity maps more accurately than presently possible. The phone sensor, however, is an imperfect device with performance variations among phones of a given model as well as between models. The sensor is the entire phone, not just the micro-machined transducer inside. A series of 1-D and 3-D shaking table tests were performed at UC San Diego and UC Berkeley, respectively, to evaluate the performance of a class of cell phones. In these tests, seven iPhones and iPod Touch devices that were mounted at different orientations were subjected to 124 earthquake ground motions to characterize their response and reliability as seismic sensors. The testing also provided insight into the seismic response of unsecured and falling instruments. The cell phones measured seismic parameters such as peak ground acceleration (PGA), peak ground velocity (PGV), peak ground displacement (PGD), and 5% damped spectral accelerations well. In general, iPhone and iPod Touch sensors slightly over-estimated ground motion energy (i.e., Arias Intensity, Ia). However, the mean acceleration response spectrum of the seven iPhones compared remarkably well with that of the reference high quality accelerometers. The error in the recorded intensity parameters was dependent on the characteristics of the input ground motion, particularly its PGA and Ia, and increased for stronger motions. The use of a high-friction device cover (e.g., rubber iPhone covers) on unsecured phones yielded substantially improved data by minimizing independent phone movement. Useful information on the ground motion characteristics was even extracted from unsecured phones during intense shaking events. The insight gained from these experiments is valuable in distilling information from a large number of imperfect signals from phones that may not be rigidly connected to the ground. With these ubiquitous measurement devices, a more accurate and rapid portrayal of the damage distribution during an earthquake can be provided to emergency responders and to the public.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bonzon, L. L.; Hente, D. B.; Kukreti, B. M.

The seismic-fragility response of naturally-aged, nuclear station, safety-related batteries is of interest for two reasons: (1) to determine actual failure modes and thresholds; and (2) to determine the validity of using the electrical capacity of individual cells as an indicator of the end-of-life of a battery, given a seismic event. This report covers the first test series of an extensive program using 12-year old, lead-calcium, Gould NCX-2250 cells, from the James A. Fitzpatrick Nuclear Power Station operated by the New York Power Authority. Seismic tests with three cell configurations were performed using a triaxial shake table: single-cell tests, rigidly mounted;more » multi-cell (three) tests, mounted in a typical battery rack; and single-cell tests specifically aimed towards examining propagation of pre-existing case cracks. In general the test philosophy was to monitor the electrical properties including discharge capacity of cells through a graduated series of g-level step increases until either the shake-table limits were reached or until electrical failure of the cells occurred. Of nine electrically active cells, six failed during seismic testing over a range of imposed g-level loads in excess of a 1-g ZPA. Post-test examination revealed a common failure mode, the cracking at the abnormally brittle, positive lead bus-bar/post interface; further examination showed that the failure zone was extremely coarse grained and extensively corroded. Presently accepted accelerated-aging methods for qualifying batteries, per IEEE Std. 535-1979, are based on plate growth, but these naturally-aged 12-year old cells showed no significant plate growth.« less

An updated geospatial liquefaction model for global application

USGS Publications Warehouse

Zhu, Jing; Baise, Laurie G.; Thompson, Eric M.

2017-01-01

We present an updated geospatial approach to estimation of earthquake-induced liquefaction from globally available geospatial proxies. Our previous iteration of the geospatial liquefaction model was based on mapped liquefaction surface effects from four earthquakes in Christchurch, New Zealand, and Kobe, Japan, paired with geospatial explanatory variables including slope-derived VS30, compound topographic index, and magnitude-adjusted peak ground acceleration from ShakeMap. The updated geospatial liquefaction model presented herein improves the performance and the generality of the model. The updates include (1) expanding the liquefaction database to 27 earthquake events across 6 countries, (2) addressing the sampling of nonliquefaction for incomplete liquefaction inventories, (3) testing interaction effects between explanatory variables, and (4) overall improving model performance. While we test 14 geospatial proxies for soil density and soil saturation, the most promising geospatial parameters are slope-derived VS30, modeled water table depth, distance to coast, distance to river, distance to closest water body, and precipitation. We found that peak ground velocity (PGV) performs better than peak ground acceleration (PGA) as the shaking intensity parameter. We present two models which offer improved performance over prior models. We evaluate model performance using the area under the curve under the Receiver Operating Characteristic (ROC) curve (AUC) and the Brier score. The best-performing model in a coastal setting uses distance to coast but is problematic for regions away from the coast. The second best model, using PGV, VS30, water table depth, distance to closest water body, and precipitation, performs better in noncoastal regions and thus is the model we recommend for global implementation.

MyShake: Building a smartphone seismic network

NASA Astrophysics Data System (ADS)

Kong, Q.; Allen, R. M.; Schreier, L.

2014-12-01

We are in the process of building up a smartphone seismic network. In order to build this network, we did shake table tests to evaluate the performance of the smartphones as seismic recording instruments. We also conducted noise floor test to find the minimum earthquake signal we can record using smartphones. We added phone noises to the strong motion data from past earthquakes, and used these as an analogy dataset to test algorithms and to understand the difference of using the smartphone network and the traditional seismic network. We also built a prototype system to trigger the smartphones from our server to record signals which can be sent back to the server in near real time. The phones can also be triggered by our developed algorithm running locally on the phone, if there's an earthquake occur to trigger the phones, the signal recorded by the phones will be sent back to the server. We expect to turn the prototype system into a real smartphone seismic network to work as a supplementary network to the existing traditional seismic network.

Bouncing ball problem: stability of the periodic modes.

PubMed

Barroso, Joaquim J; Carneiro, Marcus V; Macau, Elbert E N

2009-02-01

Exploring all its ramifications, we give an overview of the simple yet fundamental bouncing ball problem, which consists of a ball bouncing vertically on a sinusoidally vibrating table under the action of gravity. The dynamics is modeled on the basis of a discrete map of difference equations, which numerically solved fully reveals a rich variety of nonlinear behaviors, encompassing irregular nonperiodic orbits, subharmonic and chaotic motions, chattering mechanisms, and also unbounded nonperiodic orbits. For periodic motions, the corresponding conditions for stability and bifurcation are determined from analytical considerations of a reduced map. Through numerical examples, it is shown that a slight change in the initial conditions makes the ball motion switch from periodic to chaotic orbits bounded by a velocity strip v=+/-Gamma(1-epsilon) , where Gamma is the nondimensionalized shaking acceleration and epsilon the coefficient of restitution which quantifies the amount of energy lost in the ball-table collision.

Electronic relaxation effects in condensed polyacenes: A high-resolution photoemission study

NASA Astrophysics Data System (ADS)

Rocco, M. L. M.; Haeming, M.; Batchelor, D. R.; Fink, R.; Schöll, A.; Umbach, E.

2008-08-01

We present a high-resolution photoelectron spectroscopy investigation of condensed films of benzene, naphthalene, anthracene, tetracene, and pentacene. High spectroscopic resolution and a systematic variation of the molecular size allow a detailed analysis of the fine structures. The line shapes of the C 1s main lines are analyzed with respect to the different contributions of inhomogeneous broadening, vibronic coupling, and chemical shifts. The shake-up satellite spectra reveal trends, which give insight into the charge redistribution within the molecule upon photoexcitation. In particular, the shake-up between the highest occupied molecular orbital (HOMO) and the lowest unoccupied molecular orbital (LUMO) increases in intensity and moves closer toward the C 1s main line if the size of the aromatic system is increased. An explanation is given on the basis of the delocalization of the aromatic system and its capability in screening the photogenerated core hole. A comparison of the HOMO-LUMO shake-up position to the optical band gap gives additional insight into the reorganization of the electronic system upon photoexcitation.

Comparison of Cinnamon Essential Oils from Leaf and Bark with Respect to Antimicrobial Activity and Sensory Acceptability in Strawberry Shake.

PubMed

Brnawi, Wafaa I; Hettiarachchy, Navam S; Horax, Ronny; Kumar-Phillips, Geetha; Seo, Han-Seok; Marcy, John

2018-02-01

Cinnamon leaf and bark essential oils have long been used as natural preservatives and flavoring agents in foods. This study determined antimicrobial effects of leaf and bark of cinnamon essential oils (CEOs) against 2 foodborne pathogens, Salmonella Typhimurium (S.T.) and Listeria monocytogenes (L.m.), at 2 initial bacterial levels (4- and 9-log CFU/mL) in strawberry shakes. The antimicrobial study of CEOs at 0.1% and 0.5% in strawberry shakes against S.T. and L.M. showed a significant difference (P < 0.05) in log reductions of both bacterial growth at low (4-log CFU/mL) and high (9-log CFU/mL) initial bacterial levels. Addition of 0.5% CEOs into strawberry shakes at 4 °C completely inhibited both bacteria after a period of 8 d storage. Shelf-life study showed that acidity and total solid content were not affected during storage. The strawberry shakes containing bark CEO had higher ratings of sensory acceptability compared to leaf CEO, with or without the addition of 1% masking agent. In conclusion, this study demonstrated that CEO derived from bark was better than that from leaf in terms of their antimicrobial activity and sensory aspect. This study demonstrates that essential oils derived from cinnamon bark and leaf have the potential to be used as natural antimicrobial ingredient in milk beverages with respect to sensory aspect. This finding promotes the acceptance of natural antimicrobials among consumers, while providing enhanced safer products to the food industry application. © 2018 Institute of Food Technologists®.

Investigations in site response from ground motion observations in vertical arrays

NASA Astrophysics Data System (ADS)

Baise, Laurie Gaskins

The aim of the research is to improve the understanding of earthquake site response and to improve the techniques available to investigate issues in this field. Vertical array ground motion data paired with the empirical transfer function (ETF) methodology is shown to accurately characterize site response. This manuscript draws on methods developed in the field of signal processing and statistical time series analysis to parameterize the ETF as an autoregressive moving-average (ARMA) system which is justified theoretically, historically, and by example. Site response is evaluated at six sites in California, Japan, and Taiwan using ETF estimates, correlation analysis, and full waveform modeling. Correlation analysis is proposed as a required data quality evaluation imperative to any subsequent site response analysis. ETF estimates and waveform modeling are used to decipher the site response at sites with simple and complex geologic structure, which provide simple time-invariant and time-variant methods for evaluating both linear site transfer functions and nonlinear site response for sites experiencing liquefaction of the soils. The Treasure and Yerba Buena Island sites, however, require 2-D waveform modeling to accurately evaluate the effects of the shallow sedimentary basin. ETFs are used to characterize the Port Island site and corresponding shake table tests before, during, and after liquefaction. ETFs derived from the shake table tests were demonstrated to consistently predict the linear field ground response below 16 m depth and the liquefied behavior above 15 m depth. The liquefied interval response was demonstrated to gradually return to pre-liquefied conditions within several weeks of the 1995 Hyogo-ken Nanbu earthquake. Both the site's and the shake table test's response were shown to be effectively linear up to 0.5 g in the native materials below 16 m depth. The effective linearity of the site response at GVDA, Chiba, and Lotting up to 0.1 g, 0.33 g, and 0.49 g, respectively, further confirms that site response in the field may be more linear than expected from laboratory tests. Strong motions were predicted at these sites with normalized mean square error less than 0.10 using ETFs generated from weak motions. The Treasure Island site response was shown to be dominated by surface waves propagating in the shallow sediments of the San Francisco Bay. Low correlation of the ground motions recorded on rock at Yerba Buena Island and in rock beneath the Treasure Island site intimates that the Yerba Buena site is an inappropriate reference site for Treasure Island site response studies. Accurate simulation of the Treasure Island site response was achieved using a 2-D velocity structure comprised of a 100 m uniform soil basin (Vs = 400 m/s) over a weathered rock veneer (Vs = 1.5 km/s) to 200 m depth.

Temporal and spatial heterogeneity of rupture process application in shakemaps of Yushu Ms7.1 earthquake, China

NASA Astrophysics Data System (ADS)

Kun, C.

2015-12-01

Studies have shown that estimates of ground motion parameter from ground motion attenuation relationship often greater than the observed value, mainly because multiple ruptures of the big earthquake reduce the source pulse height of source time function. In the absence of real-time data of the station after the earthquake, this paper attempts to make some constraints from the source, to improve the accuracy of shakemaps. Causative fault of Yushu Ms 7.1 earthquake is vertical approximately (dip 83 °), and source process in time and space was dispersive distinctly. Main shock of Yushu Ms7.1 earthquake can be divided into several sub-events based on source process of this earthquake. Magnitude of each sub-events depended on each area under the curve of source pulse of source time function, and location derived from source process of each sub-event. We use ShakeMap method with considering the site effect to generate shakeMap for each sub-event, respectively. Finally, ShakeMaps of mainshock can be aquired from superposition of shakemaps for all the sub-events in space. Shakemaps based on surface rupture of causative Fault from field survey can also be derived for mainshock with only one magnitude. We compare ShakeMaps of both the above methods with Intensity of investigation. Comparisons show that decomposition method of main shock more accurately reflect the shake of earthquake in near-field, but for far field the shake is controlled by the weakening influence of the source, the estimated Ⅵ area was smaller than the intensity of the actual investigation. Perhaps seismic intensity in far-field may be related to the increasing seismic duration for the two events. In general, decomposition method of main shock based on source process, considering shakemap of each sub-event, is feasible for disaster emergency response, decision-making and rapid Disaster Assessment after the earthquake.

Reducing the Salt Added to Takeaway Food: Within-Subjects Comparison of Salt Delivered by Five and 17 Holed Salt Shakers in Controlled Conditions

PubMed Central

Goffe, Louis; Wrieden, Wendy; Penn, Linda; Hillier-Brown, Frances; Lake, Amelia A.; Araujo-Soares, Vera; Summerbell, Carolyn; White, Martin; Adamson, Ashley J.

2016-01-01

Objectives To determine if the amount of salt delivered by standard salt shakers commonly used in English independent takeaways varies between those with five and 17 holes; and to determine if any differences are robust to variations in: the amount of salt in the shaker, the length of time spent shaking, and the person serving. Design Four laboratory experiments comparing the amount of salt delivered by shakers. Independent variables considered were: type of shaker used (five or 17 holes), amount of salt in the shaker before shaking commences (shaker full, half full or nearly empty), time spent shaking (3s, 5s or 10s), and individual serving. Setting Controlled, laboratory, conditions. Participants A quota-based convenience sample of 10 participants (five women) aged 18–59 years. Main Outcome Measures Amount of salt delivered by salt shakers. Results Across all trials, the 17 holed shaker delivered a mean (SD) of 7.86g (4.54) per trial, whilst the five holed shaker delivered 2.65g (1.22). The five holed shaker delivered a mean of 33.7% of the salt of the 17 holed shaker. There was a significant difference in salt delivered between the five and 17 holed salt shakers when time spent shaking, amount of salt in the shaker and participant were all kept constant (p<0.001). This difference was robust to variations in the starting weight of shakers, time spent shaking and participant shaking (ps

Comparison of Oregon state highway division Table-1 and Table-2 asphalt : final report.

DOT National Transportation Integrated Search

1991-12-01

The objective of this study was to compare the effect of using the Oregon State Highway Division (OSHD) modified Table-1 asphalts and the OSHD modified Table-2 asphalts in asphalt concrete; the primary factors for comparison were reflective and therm...

Shaking table experimentation on adjacent structures controlled by passive and semi-active MR dampers

NASA Astrophysics Data System (ADS)

Basili, M.; De Angelis, M.; Fraraccio, G.

2013-06-01

This paper presents the results of shaking table tests on adjacent structures controlled by passive and semi-active MR dampers. The aim was to demonstrate experimentally the effectiveness of passive and semi-active strategies in reducing structural vibrations due to seismic excitation. The physical model at issue was represented by two adjacent steel structures, respectively of 4 and 2 levels, connected at the second level by a MR damper. When the device operated in semi-active mode, an ON-OFF control algorithm, derived by the Lyapunov stability theory, was implemented and experimentally validated. Since the experimentation concerned adjacent structures, two control objectives have been reached: global and selective protection. In case of global protection, the attention was focused on protecting both structures, whereas, in case of selective protection, the attention was focused on protecting only one structure. For each objective the effectiveness of passive control has been compared with the situation of no control and then the effectiveness of semi-active control has been compared with the passive one. The quantities directly compared have been: measured displacements, accelerations and force-displacement of the MR damper, moreover some global response quantities have been estimated from experimental measures, which are the base share force and the base bending moment, the input energy and the energy dissipated by the device. In order to evaluate the effectiveness of the control action in both passive and semi-active case, an energy index EDI, previously defined and already often applied numerically, has been utilized. The aspects investigated in the experimentation have been: the implementation and validation of the control algorithm for selective and global protection, the MR damper input voltage influence, the kind of seismic input and its intensity.

Development of the monitoring technique on the damage of piles using the biggest shaking table "E-defense"

NASA Astrophysics Data System (ADS)

Hayashi, Kazuhiro; Hachimori, Wataru; Kaneda, Shogo; Tamura, Shuji; Saito, Taiki

2017-10-01

In case of earthquake damage to buildings, the damage to a superstructure is visible, but the damage to a foundation structure, e.g. the underground pile, is difficult to detect. In this study, the authors aim to develop a monitoring technique for pile damage due to earthquakes. The world's biggest shaking table, E-Defense, was used to reproduce damage to RC pile models embedded in the soil inside a large scale shear box (8m in diameter and 6.5m in height). The diameter of the RC pile model was 154mm. It consisted of mortar (27.2N/mm2 in compressive strength), 6 main reinforcements (6.35mm in diameter) and shear reinforcement hard steel wire (2mm in diameter at intervals of 20mm). The natural period of the superstructure above the pile models is around 0.12sec. The soil consisted of 2 layers. The lower layer is Albany sand of 80% relative density while the upper layer is only 2m from the surface ground and is Kaketsu sand of 60% relative density. Primary four excitations were scaled from JMA Kobe waves in notification at different amplitudes. The maximum acceleration of each wave is 31gal, 67gal, 304gal, and 458gal, respectively. In the test result, reinforcing steels at the pile head of the RC model yielded when the maximum acceleration was 304gal. After that, mortar of the pile head peeled off and a bending shear failure occurred when the maximum acceleration was 458gal. The peak frequency of rotational spectrum on the foundation did not change in elastic range in the piles. However, the peak frequency fell after the plastic hinge occurred.

"Did you feel it?" Intensity data: A surprisingly good measure of earthquake ground motion

USGS Publications Warehouse

Atkinson, G.M.; Wald, D.J.

2007-01-01

The U.S. Geological Survey is tapping a vast new source of engineering seismology data through its "Did You Feel It?" (DYFI) program, which collects online citizen responses to earthquakes. To date, more than 750,000 responses have been compiled in the United States alone. The DYFI data make up in quantity what they may lack in scientific quality and offer the potential to resolve longstanding issues in earthquake ground-motion science. Such issues have been difficult to address due to the paucity of instrumental ground-motion data in regions of low seismicity. In particular, DYFI data provide strong evidence that earthquake stress drops, which control the strength of high-frequency ground shaking, are higher in the central and eastern United States (CEUS) than in California. Higher earthquake stress drops, coupled with lower attenuation of shaking with distance, result in stronger overall shaking over a wider area and thus more potential damage for CEUS earthquakes in comparison to those of equal magnitude in California - a fact also definitively captured with these new DYFI data and maps.

Comparison of extraction techniques of robenidine from poultry feed samples.

PubMed

Wilga, Joanna; Wasik, Agata Kot-; Namieśnik, Jacek

2007-10-31

In this paper, effectiveness of six different commonly applied extraction techniques for the determination of robenidine in poultry feed has been compared. The sample preparation techniques included shaking, Soxhlet, Soxtec, ultrasonically assisted extraction, microwave - assisted extraction and accelerated solvent extraction. Comparison of these techniques was done with respect to the recovery extraction, temperature and time, reproducibility and solvent consumption. Every single extract was subjected to clean - up using aluminium oxide column (Pasteur pipette filled with 1g of aluminium oxide), from which robenidine was eluted with 10ml of methanol. The eluate from the clean-up column was collected in a volumetric flask, and finally it was analysed by HPLC-DAD-MS. In general, all extraction techniques were capable of isolating of robenidine from poultry feed, but the recovery obtained using modern extraction techniques was higher than that obtained using conventional techniques. In particular, accelerated solvent extraction was more superior to other techniques, which highlights the advantages of this sample preparation technique. However, in routine analysis, shaking and ultrasonically assisted extraction is still the preferred method for the solution of robenidine and other coccidiostatics.

Practices of shake-flask culture and advances in monitoring CO2 and O2.

PubMed

Takahashi, Masato; Aoyagi, Hideki

2018-05-01

About 85 years have passed since the shaking culture was devised. Since then, various monitoring devices have been developed to measure culture parameters. O 2 consumed and CO 2 produced by the respiration of cells in shaking cultures are of paramount importance due to their presence in both the culture broth and headspace of shake flask. Monitoring in situ conditions during shake-flask culture is useful for analysing the behaviour of O 2 and CO 2 , which interact according to Henry's law, and is more convenient than conventional sampling that requires interruption of shaking. In situ monitoring devices for shake-flask cultures are classified as direct or the recently developed bypass type. It is important to understand the characteristics of each type along with their unintended effect on shake-flask cultures, in order to improve the existing devices and culture conditions. Technical developments in the bypass monitoring devices are strongly desired in the future. It is also necessary to understand the mechanism underlying conventional shake-flask culture. The existing shaking culture methodology can be expanded into next-generation shake-flask cultures constituting a novel culture environment through a judicious selection of monitoring devices depending on the intended purpose of shake-flask culture. Construction and sharing the databases compatible with the various types of the monitoring devices and measurement instruments adapted for shaking culture can provide a valuable resource for broadening the application of cells with shake-flask culture.

Nofoam System Technology for Aircraft Hangar Fire Suppression Foam System

DTIC Science & Technology

2011-07-01

use of a firefighting agent that meets Military Specification MIL - F - 24385 [Reference 2]. Significant amounts of AFFF wastewater is generated...rates, Table 3, were the established baseline for comparison. Table 3 theoretical flow rates were derived from Military Specification MIL - F - 24385 [Reference...flow rates, Table 3, was the established baseline for comparison. Table 3 theoretical flow rates were derived from Military Specification MIL - F - 24385 [Reference

Comparison of Human Response against Earthquake and Tsunami

NASA Astrophysics Data System (ADS)

Arikawa, T.; Güler, H. G.; Yalciner, A. C.

2017-12-01

The evacuation response against the earthquake and tsunamis is very important for the reduction of human damages against tsunami. But it is very difficult to predict the human behavior after shaking of the earthquake. The purpose of this research is to clarify the difference of the human response after the earthquake shock in the difference countries and to consider the relation between the response and the safety feeling, knowledge and education. For the objective of this paper, the questionnaire survey was conducted after the 21st July 2017 Gokova earthquake and tsunami. Then, consider the difference of the human behavior by comparison of that in 2015 Chilean earthquake and tsunami and 2011 Japan earthquake and tsunami. The seismic intensity of the survey points was almost 6 to 7. The contents of the questions include the feeling of shaking, recalling of the tsunami, the behavior after shock and so on. The questionnaire was conducted for more than 20 20 people in 10 areas. The results are the following; 1) Most people felt that it was a strong shake not to stand, 2) All of the questionnaires did not recall the tsunami, 3) Depending on the area, they felt that after the earthquake the beach was safer than being at home. 4) After they saw the sea drawing, they thought that a tsunami would come and ran away. Fig. 1 shows the comparison of the evacuation rate within 10 minutes in 2011 Japan, 2015 Chile and 2017 Turkey.. From the education point of view, education for tsunami is not done much in Turkey. From the protection facilities point of view, the high sea walls are constructed only in Japan. From the warning alert point of view, there is no warning system against tsunamis in the Mediterranean Sea. As a result of this survey, the importance of tsunami education is shown, and evacuation tends to be delayed if dependency on facilities and alarms is too high.

Developing ShakeCast statistical fragility analysis framework for rapid post-earthquake assessment

USGS Publications Warehouse

Lin, K.-W.; Wald, D.J.

2012-01-01

When an earthquake occurs, the U. S. Geological Survey (USGS) ShakeMap estimates the extent of potentially damaging shaking and provides overall information regarding the affected areas. The USGS ShakeCast system is a freely-available, post-earthquake situational awareness application that automatically retrieves earthquake shaking data from ShakeMap, compares intensity measures against users’ facilities, sends notifications of potential damage to responsible parties, and generates facility damage assessment maps and other web-based products for emergency managers and responders. We describe notable improvements of the ShakeMap and the ShakeCast applications. We present a design for comprehensive fragility implementation, integrating spatially-varying ground-motion uncertainties into fragility curves for ShakeCast operations. For each facility, an overall inspection priority (or damage assessment) is assigned on the basis of combined component-based fragility curves using pre-defined logic. While regular ShakeCast users receive overall inspection priority designations for each facility, engineers can access the full fragility analyses for further evaluation.

Strong-motion observations of the M 7.8 Gorkha, Nepal, earthquake sequence and development of the N-shake strong-motion network

USGS Publications Warehouse

Dixit, Amod; Ringler, Adam; Sumy, Danielle F.; Cochran, Elizabeth S.; Hough, Susan E.; Martin, Stacey; Gibbons, Steven; Luetgert, James H.; Galetzka, John; Shrestha, Surya; Rajaure, Sudhir; McNamara, Daniel E.

2015-01-01

We present and describe strong-motion data observations from the 2015 M 7.8 Gorkha, Nepal, earthquake sequence collected using existing and new Quake-Catcher Network (QCN) and U.S. Geological Survey NetQuakes sensors located in the Kathmandu Valley. A comparison of QCN data with waveforms recorded by a conventional strong-motion (NetQuakes) instrument validates the QCN data. We present preliminary analysis of spectral accelerations, and peak ground acceleration and velocity for earthquakes up to M 7.3 from the QCN stations, as well as preliminary analysis of the mainshock recording from the NetQuakes station. We show that mainshock peak accelerations were lower than expected and conclude the Kathmandu Valley experienced a pervasively nonlinear response during the mainshock. Phase picks from the QCN and NetQuakes data are also used to improve aftershock locations. This study confirms the utility of QCN instruments to contribute to ground-motion investigations and aftershock response in regions where conventional instrumentation and open-access seismic data are limited. Initial pilot installations of QCN instruments in 2014 are now being expanded to create the Nepal–Shaking Hazard Assessment for Kathmandu and its Environment (N-SHAKE) network.

How well can we test probabilistic seismic hazard maps?

NASA Astrophysics Data System (ADS)

Vanneste, Kris; Stein, Seth; Camelbeeck, Thierry; Vleminckx, Bart

2017-04-01

Recent large earthquakes that gave rise to shaking much stronger than shown in probabilistic seismic hazard (PSH) maps have stimulated discussion about how well these maps forecast future shaking. These discussions have brought home the fact that although the maps are designed to achieve certain goals, we know little about how well they actually perform. As for any other forecast, this question involves verification and validation. Verification involves assessing how well the algorithm used to produce hazard maps implements the conceptual PSH model ("have we built the model right?"). Validation asks how well the model forecasts the shaking that actually occurs ("have we built the right model?"). We explore the verification issue by simulating shaking histories for an area with assumed uniform distribution of earthquakes, Gutenberg-Richter magnitude-frequency relation, Poisson temporal occurrence model, and ground-motion prediction equation (GMPE). We compare the maximum simulated shaking at many sites over time with that predicted by a hazard map generated for the same set of parameters. The Poisson model predicts that the fraction of sites at which shaking will exceed that of the hazard map is p = 1 - exp(-t/T), where t is the duration of observations and T is the map's return period. Exceedance is typically associated with infrequent large earthquakes, as observed in real cases. The ensemble of simulated earthquake histories yields distributions of fractional exceedance with mean equal to the predicted value. Hence, the PSH algorithm appears to be internally consistent and can be regarded as verified for this set of simulations. However, simulated fractional exceedances show a large scatter about the mean value that decreases with increasing t/T, increasing observation time and increasing Gutenberg-Richter a-value (combining intrinsic activity rate and surface area), but is independent of GMPE uncertainty. This scatter is due to the variability of earthquake recurrence, and so decreases as the largest earthquakes occur in more simulations. Our results are important for evaluating the performance of a hazard map based on misfits in fractional exceedance, and for assessing whether such misfit arises by chance or reflects a bias in the map. More specifically, we determined for a broad range of Gutenberg-Richter a-values theoretical confidence intervals on allowed misfits in fractional exceedance and on the percentage of hazard-map bias that can thus be detected by comparison with observed shaking histories. Given that in the real world we only have one shaking history for an area, these results indicate that even if a hazard map does not fit the observations, it is very difficult to assess its veracity, especially for low-to-moderate-seismicity regions. Because our model is a simplified version of reality, any additional uncertainty or complexity will tend to widen these confidence intervals.

Some problems of control of dynamical conditions of technological vibrating machines

NASA Astrophysics Data System (ADS)

Kuznetsov, N. K.; Lapshin, V. L.; Eliseev, A. V.

2017-10-01

The possibility of control of dynamical condition of the shakers that are designed for vibration treatment of parts interacting with granular media is discussed. The aim of this article is to develop the methodological basis of technology of creation of mathematical models of shake tables and the development of principles of formation of vibrational fields, estimation of their parameters and control of the structure vibration fields. Approaches to build mathematical models that take into account unilateral constraints, the relationships between elements, with the vibrating surface are developed. Methods intended to construct mathematical model of linear mechanical oscillation systems are used. Small oscillations about the position of static equilibrium are performed. The original method of correction of vibration fields by introduction of the oscillating system additional ties to the structure are proposed. Additional ties are implemented in the form of a mass-inertial device for changing the inertial parameters of the working body of the vibration table by moving the mass-inertial elements. The concept of monitoring the dynamic state of the vibration table based on the original measuring devices is proposed. Estimation for possible changes in dynamic properties is produced. The article is of interest for specialists in the field of creation of vibration technology machines and equipment.

Soft-sediment deformation in New Zealand: Structures resulting from the 2010/11 Christchurch earthquakes and comparison with Pleistocene sediments of the Taupo Volcanic Zone (TVZ)

NASA Astrophysics Data System (ADS)

Scholz, C.; Downs, D. T.; Gravley, D.; Quigley, M.; Rowland, J. V.

2011-12-01

The distinction between seismites and other event-related soft-sediment deformation is a challenging problem. Recognition and interpretation is aided by comparison of recent examples produced during known seismic events and those generated experimentally. Seismites are important features, once recognized in a rock, for interpretations of paleotectonic environment, tectonic relationships of sediments in basins, sedimentary facies analysis, evaluation of earthquake frequency and hazard and consequent land managment. Two examples of soft-sediment deformation, potentially generated through ground shaking and associated liquefaction, are described from within the TVZ: 1) Near Matata on the western margin of the Whakatane Graben. This location has a complicated en-echelon fault history and large earthquakes occur from time to time (e.g., 1987 ML6.3 Edgecumbe event). The structures occur in ~550 ka volcanic sediments, and represent soft-sediment deformation within stratigraphically-bounded layers. Based on paleoenvironment, appearance, and diagnostic criteria described by other authors (Sims 1975; Hempton and Dewey 1983), we interpret these features to have formed by ground shaking related to an earthquake and/or possibly accompanying large volcanic eruptions, rather than by slope failure. 2) Near Taupo, 3 km from the active Kaiapo fault. Lakeward dipping, nearly horizontal lacustrine sediments overlay Taupo Ignimbrite (1.8 ka). At one outcrop the lake beds have subsided into the underlying substrate resulting in kidney-shaped features. These structures formed as a result of liquefaction of the underlying substrate, which may have been caused by ground shaking related to either seismic or volcanic activity. However, inferred time relationships are more consistent with seismic-induced ground shaking. We compare and contrast the form and geometry of the above structures with seismites generated during the recent Christchurch earthquakes (Sep. 2010 and Feb. 2011). Hempton, M. R. and J. F. Dewey (1983). "Earthquake-induced deformational structures in young lacustrine sediments, East Anatolian Fault, southeast Turkey." Tectonophysics 98(3-4): T7-T14. Sims, J. D. (1975). "Determining earthquake recurrence intervals from deformational structures in young lacustrine sediments." Tectonophysics 29(1-4): 141-152.

Comparison of tungsten carbide and stainless steel ball bearings for grinding single maize kernels in a reciprocating grinder

USDA-ARS?s Scientific Manuscript database

Reciprocating grinders can grind single maize kernels by shaking the kernel in a vial with a ball bearing. This process results in a grind quality that is not satisfactory for many experiments. Tungesten carbide ball bearings are nearly twice as dense as steel, so we compared their grinding performa...

Experimental Study on Steel Tank Model Using Shaking Table/ Badania Eksperymentalne Modelu Zbiornika Stalowego Na Stole Sejsmicznym

NASA Astrophysics Data System (ADS)

Burkacki, Daniel; Jankowski, Robert

2014-09-01

Cylindrical steel tanks are very popular structures used for storage of products of chemical and petroleum industries. Earthquakes are the most dangerous and also the most unpredictable dynamic loads acting on such structures. On the other hand, mining tremors are usually considered to be less severe due to lower acceleration levels observed. The aim of the present paper is to show the results of the experimental study which has been conducted on a scaled model of a real tank located in Poland. The investigation has been carried out under different dynamic excitations (earthquakes and mining tremors) using the shaking table. The results of the study indicate that stored product may significantly influence the values of dynamic parameters and confirm that the level of liquid filling is really essential in the structural analysis. The comparison of the response under moderate earthquakes and mining tremors indicate that the second excitation may be more severe in some cases. Stalowe zbiorniki walcowe są bardzo popularnymi konstrukcjami używanymi do magazynowania produktów przemysłu chemicznego i naftowego. Ich bezpieczeństwo i niezawodność są kluczowe, ponieważ każde uszkodzenie może nieść za sobą bardzo poważne konsekwencje. Trzęsienia ziemi są najbardziej niebezpiecznymi, a zarazem najbardziej nieprzewidywalnymi obciążeniami dynamicznymi, które mogą oddziaływać na tego typu konstrukcje. Z drugiej strony ruchy podłoża związane ze wstrząsami górniczymi są uważane za mniej groźne z powodu osiągania niższych poziomów wartości przyspieszeń. Celem niniejszego artykułu jest przedstawienie wyników badań eksperymentalnych, które przeprowadzono na wykonanym w skali modelu rzeczywistego zbiornika zlokalizowanego na terenie Polski. Badania wykonano przy użyciu stołu sejsmicznego. Zakres badań obejmował testy harmoniczne właściwości dynamicznych oraz zachowanie się stalowego zbiornika walcowego podczas trzęsień ziemi oraz wstrząsów górniczych dla różnych poziomów wypełnienia cieczą. Wyniki badań pokazują, że produkt magazynowany może mieć znaczący wpływ na wartości parametrów dynamicznych oraz potwierdzają, iż poziom wypełnienia cieczą jest istotny w analizie konstrukcji. Porównanie odpowiedzi podczas trzęsień ziemi oraz wstrząsów górniczych wskazuje, iż to drugie wymuszenie może być w niektórych przypadkach bardziej niekorzystne.

U.S. Geological Survey's ShakeCast: A cloud-based future

USGS Publications Warehouse

Wald, David J.; Lin, Kuo-Wan; Turner, Loren; Bekiri, Nebi

2014-01-01

When an earthquake occurs, the U. S. Geological Survey (USGS) ShakeMap portrays the extent of potentially damaging shaking. In turn, the ShakeCast system, a freely-available, post-earthquake situational awareness application, automatically retrieves earthquake shaking data from ShakeMap, compares intensity measures against users’ facilities, sends notifications of potential damage to responsible parties, and generates facility damage assessment maps and other web-based products for emergency managers and responders. ShakeCast is particularly suitable for earthquake planning and response purposes by Departments of Transportation (DOTs), critical facility and lifeline utilities, large businesses, engineering and financial services, and loss and risk modelers. Recent important developments to the ShakeCast system and its user base are described. The newly-released Version 3 of the ShakeCast system encompasses advancements in seismology, earthquake engineering, and information technology applicable to the legacy ShakeCast installation (Version 2). In particular, this upgrade includes a full statistical fragility analysis framework for general assessment of structures as part of the near real-time system, direct access to additional earthquake-specific USGS products besides ShakeMap (PAGER, DYFI?, tectonic summary, etc.), significant improvements in the graphical user interface, including a console view for operations centers, and custom, user-defined hazard and loss modules. The release also introduces a new adaption option to port ShakeCast to the "cloud". Employing Amazon Web Services (AWS), users now have a low-cost alternative to local hosting, by fully offloading hardware, software, and communication obligations to the cloud. Other advantages of the "ShakeCast Cloud" strategy include (1) Reliability and robustness of offsite operations, (2) Scalability naturally accommodated, (3), Serviceability, problems reduced due to software and hardware uniformity, (4) Testability, freely available for new users, (5) Remotely supported, allowing expert-facilitated maintenance, (6) Adoptability, simplified with disk images, and (7) Security, built in at the very high level associated with AWS. The ShakeCast user base continues to expand and broaden. For example, Caltrans, the prototypical ShakeCast user and development supporter, has been providing guidance to other DOTs on the use of the National Bridge Inventory (NBI) database to implement fully-functional ShakeCast systems in their states. A long-term goal underway is to further "connect the DOTs" via a Transportation Pooled Fund (TPF) with participating state DOTs. We also review some of the many other users and uses of ShakeCast. Lastly, on the hazard input front, we detail related ShakeMap improvements and ongoing advancements in estimating the likelihood of shaking-induced secondary hazards at structures, facilities, bridges, and along roadways due to landslides and liquefaction, and implemented within the ShakeCast framework.

Decoupling the structure from the ground motion during earthquakes by employing friction pendulums

NASA Astrophysics Data System (ADS)

Gillich, G. R.; Iancu, V.; Gillich, N.; Korka, Z. I.; Chioncel, C. P.; Hatiegan, C.

2018-01-01

Avoiding dynamic loads on structures during earthquakes is an actual issue since seismic actions can harm or destroy the built environment. Several attempts to prevent this are possible, the essence being to decouple the structure from the ground motion during earthquakes and preventing in this way large deflections and high accelerations. A common approach is the use of friction pendulums, with cylindrical or spherical surfaces but not limited to that, inserted between the ground and the structure, respectively between the pillar and the superstructure. This type of bearings permits small pendulum motion and in this way, earthquake-induced displacements that occur in the bearings are not integrally transmitted to the structure. The consequence is that the structure is subject to greatly reduced lateral loads and shaking movements. In the experiments, conducted to prove the efficiency of the friction pendulums, we made use of an own designed and manufactured shaking table. Two types of sliding surfaces are analyzed, one polynomial of second order (i.e. circular) and one of a superior order. For both pendulum types, analytical models were developed. The results have shown that the structure is really decoupled from the ground motion and has a similar behaviour as that described by the analytic model.

A Simple Probabilistic Model for Estimating the Risk of Standard Air Dives

DTIC Science & Technology

2004-12-01

Decompression Models Table Al. Decompression Table Based on the StandAir Model and Comparison with the VVaI-1 8 Algorithm. A-l-A-4 Table A2. The VVaI-1 8...cannot be as strong as might be desired - especially for dives with long TDTs. Comparisons of the positions of the dive-outcome symbols with the... comparisons for several depth/bottom-time combinations. The three left-hand panels, for dives with short bottom times, show that the crossover point

USGS ShakeMap Developments, Implementation, and Derivative Tools

NASA Astrophysics Data System (ADS)

Wald, D. J.; Lin, K.; Quitoriano, V.; Worden, B.

2007-12-01

We discuss ongoing development and enhancements of ShakeMap, a system for automatically generating maps of ground shaking and intensity in the minutes following an earthquake. The rapid availability of these maps is of particular value to emergency response organizations, utilities, insurance companies, government decision- makers, the media, and the general public. ShakeMap Version 3.2 was released in March, 2007, on a download site which allows ShakeMap developers to track operators' updates and provide follow-up information; V3.2 has now been downloaded in 15 countries. The V3.2 release supports LINUX in addition to other UNIX operating systems and adds enhancements to XML, KML, metadata, and other products. We have also added an uncertainty measure, quantified as a function of spatial location. Uncertainty is essential for evaluating the range of possible losses. Though not released in V3.2, we will describe a new quantitative uncertainty letter grading for each ShakeMap produced, allowing users to gauge the appropriate level of confidence when using rapidly produced ShakeMaps as part of their post-earthquake critical decision-making process. Since the V3.2 release, several new ground motion predictions equations have also been added to the prediction equation modules. ShakeMap is implemented in several new regions as reported in this Session. Within the U.S., robust systems serve California, Nevada, Utah, Washington and Oregon, Hawaii, and Anchorage. Additional systems are in development and efforts to provide backup capabilities for all Advanced National Seismic System (ANSS) regions at the National Earthquake Information Center are underway. Outside the U.S., this Session has descriptions of ShakeMap systems in Italy, Switzerland, Romania, and Turkey, among other countries. We also describe our predictive global ShakeMap system for the rapid evaluation of significant earthquakes globally for the Prompt Assessment of Global Earthquakes for Response (PAGER) system. These global ShakeMaps are constrained by rapidly gathered intensity data via the Internet and by finite fault and aftershock analyses for portraying fault rupture dimensions. As part of the PAGER loss calibration process we have produced an Atlas of ShakeMaps for significant earthquakes around the globe since 1973 (Allen and others, this Session); these Atlas events have additional constraints provided by archival strong motion, faulting dimensions, and macroseismic intensity data. We also describe derivative tools for further utilizing ShakeMap including ShakeCast, a fully automated system for delivering specific ShakeMap products to critical users and triggering established post-earthquake response protocols. We have released ShakeCast Version 2.0 (Lin and others, this Session), which allows RSS feeds for automatically receiving ShakeMap files, auto-launching of post-download processing scripts, and delivering notifications based on users' likely facility damage states derived from ShakeMap shaking parameters. As part of our efforts to produce estimated ShakeMaps globally, we have developed a procedure for deriving Vs30 estimates from correlations with topographic slope, and we have now implemented a global Vs30 Server, allowing users to generate Vs30 maps for custom user-selected regions around the globe (Allen and Wald, this Session). Finally, as a further derivative product of the ShakeMap Atlas project, we will present a shaking hazard Map for the past 30 years based on approximately 3,900 earthquake ShakeMaps of historic earthquakes.

ShakeCast: Automating and Improving the Use of ShakeMap for Post-Earthquake Decision- Making and Response

NASA Astrophysics Data System (ADS)

Lin, K.; Wald, D. J.

2007-12-01

ShakeCast is a freely available, post-earthquake situational awareness application that automatically retrieves earthquake shaking data from ShakeMap, compares intensity measures against users" facilities, sends notifications of potential damage to responsible parties, and generates facility damage maps and other Web-based products for emergency managers and responders. ShakeMap, a tool used to portray the extent of potentially damaging shaking following an earthquake, provides overall information regarding the affected areas. When a potentially damaging earthquake occurs, utility and other lifeline managers, emergency responders, and other critical users have an urgent need for information about the impact on their particular facilities so they can make appropriate decisions and take quick actions to ensure safety and restore system functionality. To this end, ShakeCast estimates the potential damage to a user's widely distributed facilities by comparing the complex shaking distribution with the potentially highly variable damageability of their inventory to provide a simple, hierarchical list and maps showing structures or facilities most likely impacted. All ShakeMap and ShakeCast files and products are non-propriety to simplify interfacing with existing users" response tools and to encourage user-made enhancement to the software. ShakeCast uses standard RSS and HTTP requests to communicate with the USGS Web servers that host ShakeMaps, which are widely-distributed and heavily mirrored. The RSS approach allows ShakeCast users to initiate and receive selected ShakeMap products and information on software updates. To assess facility damage estimates, ShakeCast users can combine measured or estimated ground motion parameters with damage relationships that can be pre-computed, use one of these ground motion parameters as input, and produce a multi-state discrete output of damage likelihood. Presently three common approaches are being used to provide users with an indication of damage: HAZUS-based, intensity-based, and customized damage functions. Intensity-based thresholds are for locations with poorly established damage relationships; custom damage levels are for advanced ShakeCast users such as Caltrans which produces its own set of damage functions that correspond to the specific details of each California bridge or overpass in its jurisdiction. For users whose portfolio of structures is comprised of common, standard designs, ShakeCast offers a simplified structural damage-state estimation capability adapted from the HAZUS-MH earthquake module (NIBS and FEMA, 2003). Currently the simplified fragility settings consist of 128 combinations of HAZUS model building types, construction materials, building heights, and building-code eras.

ShakeCast: Automating and improving the use of shakemap for post-earthquake deeision-making and response

USGS Publications Warehouse

Wald, D.; Lin, K.-W.; Porter, K.; Turner, Loren

2008-01-01

When a potentially damaging earthquake occurs, utility and other lifeline managers, emergency responders, and other critical users have an urgent need for information about the impact on their particular facilities so they can make appropriate decisions and take quick actions to ensure safety and restore system functionality. ShakeMap, a tool used to portray the extent of potentially damaging shaking following an earthquake, on its own can be useful for emergency response, loss estimation, and public information. However, to take full advantage of the potential of ShakeMap, we introduce ShakeCast. ShakeCast facilitates the complicated assessment of potential damage to a user's widely distributed facilities by comparing the complex shaking distribution with the potentially highly variable damageability of their inventory to provide a simple, hierarchical list and maps of structures or facilities most likely impacted. ShakeCast is a freely available, post-earthquake situational awareness application that automatically retrieves earthquake shaking data from ShakeMap, compares intensity measures against users' facilities, sends notifications of potential damage to responsible parties, and generates facility damage maps and other Web-based products for both public and private emergency managers and responders. ?? 2008, Earthquake Engineering Research Institute.

MOIL-opt: Energy-Conserving Molecular Dynamics on a GPU/CPU system

PubMed Central

Ruymgaart, A. Peter; Cardenas, Alfredo E.; Elber, Ron

2011-01-01

We report an optimized version of the molecular dynamics program MOIL that runs on a shared memory system with OpenMP and exploits the power of a Graphics Processing Unit (GPU). The model is of heterogeneous computing system on a single node with several cores sharing the same memory and a GPU. This is a typical laboratory tool, which provides excellent performance at minimal cost. Besides performance, emphasis is made on accuracy and stability of the algorithm probed by energy conservation for explicit-solvent atomically-detailed-models. Especially for long simulations energy conservation is critical due to the phenomenon known as “energy drift” in which energy errors accumulate linearly as a function of simulation time. To achieve long time dynamics with acceptable accuracy the drift must be particularly small. We identify several means of controlling long-time numerical accuracy while maintaining excellent speedup. To maintain a high level of energy conservation SHAKE and the Ewald reciprocal summation are run in double precision. Double precision summation of real-space non-bonded interactions improves energy conservation. In our best option, the energy drift using 1fs for a time step while constraining the distances of all bonds, is undetectable in 10ns simulation of solvated DHFR (Dihydrofolate reductase). Faster options, shaking only bonds with hydrogen atoms, are also very well behaved and have drifts of less than 1kcal/mol per nanosecond of the same system. CPU/GPU implementations require changes in programming models. We consider the use of a list of neighbors and quadratic versus linear interpolation in lookup tables of different sizes. Quadratic interpolation with a smaller number of grid points is faster than linear lookup tables (with finer representation) without loss of accuracy. Atomic neighbor lists were found most efficient. Typical speedups are about a factor of 10 compared to a single-core single-precision code. PMID:22328867

MyShake - Smartphone seismic network powered by citizen scientists

NASA Astrophysics Data System (ADS)

Kong, Q.; Allen, R. M.; Schreier, L.; Strauss, J. A.

2017-12-01

MyShake is a global smartphone seismic network that harnesses the power of crowdsourcing. It is driven by the citizen scientists that run MyShake on their personal smartphones. It has two components: an android application running on the smartphones to detect earthquake-like motion, and a network detection algorithm to aggregate results from multiple smartphones to confirm when an earthquake occurs. The MyShake application was released to the public on Feb 12th 2016. Within the first year, more than 250,000 people downloaded MyShake app around the world. There are more than 500 earthquakes recorded by the smartphones in this period, including events in Chile, Argentina, Mexico, Morocco, Greece, Nepal, New Zealand, Taiwan, Japan, and across North America. Currently, we are working on earthquake early warning with MyShake network and the shaking data provided by MyShake is a unique dataset that can be used for the research community.

Table of Comparison of 2012 CDR v 2006 IUR Definitions

EPA Pesticide Factsheets

In forming 40 CFR 711, EPA sought to simplify the definition section and remove unnecessary duplication of regulatory terms. This table is a comparison of 2006 IUR Definitions and 2012 CDR Definitions.

ShakeCast Manual

USGS Publications Warehouse

Lin, Kuo-Wan; Wald, David J.

2008-01-01

ShakeCast is a freely available, post-earthquake situational awareness application that automatically retrieves earthquake shaking data from ShakeMap, compares intensity measures against users? facilities, and generates potential damage assessment notifications, facility damage maps, and other Web-based products for emergency managers and responders.

Fan Blade Shake Test Results for the 40- by 80-/80- by 120-Foot Wind Tunnel

NASA Technical Reports Server (NTRS)

Warmbrodt, W.; Graham, T.

1983-01-01

This report documents the shake tests performed on the first set of hydulignum fan blades for the 40- by 80-/80- by 120-Foot Wind Tunnel. The purpose of the shake test program is described. The test equipment and test procedures are reviewed. Results from each shake test are presented and the overall findings of the shake test program are discussed.

Neo-Deterministic and Probabilistic Seismic Hazard Assessments: a Comparative Analysis

NASA Astrophysics Data System (ADS)

Peresan, Antonella; Magrin, Andrea; Nekrasova, Anastasia; Kossobokov, Vladimir; Panza, Giuliano F.

2016-04-01

Objective testing is the key issue towards any reliable seismic hazard assessment (SHA). Different earthquake hazard maps must demonstrate their capability in anticipating ground shaking from future strong earthquakes before an appropriate use for different purposes - such as engineering design, insurance, and emergency management. Quantitative assessment of maps performances is an essential step also in scientific process of their revision and possible improvement. Cross-checking of probabilistic models with available observations and independent physics based models is recognized as major validation procedure. The existing maps from the classical probabilistic seismic hazard analysis (PSHA), as well as those from the neo-deterministic analysis (NDSHA), which have been already developed for several regions worldwide (including Italy, India and North Africa), are considered to exemplify the possibilities of the cross-comparative analysis in spotting out limits and advantages of different methods. Where the data permit, a comparative analysis versus the documented seismic activity observed in reality is carried out, showing how available observations about past earthquakes can contribute to assess performances of the different methods. Neo-deterministic refers to a scenario-based approach, which allows for consideration of a wide range of possible earthquake sources as the starting point for scenarios constructed via full waveforms modeling. The method does not make use of empirical attenuation models (i.e. Ground Motion Prediction Equations, GMPE) and naturally supplies realistic time series of ground shaking (i.e. complete synthetic seismograms), readily applicable to complete engineering analysis and other mitigation actions. The standard NDSHA maps provide reliable envelope estimates of maximum seismic ground motion from a wide set of possible scenario earthquakes, including the largest deterministically or historically defined credible earthquake. In addition, the flexibility of NDSHA allows for generation of ground shaking maps at specified long-term return times, which may permit a straightforward comparison between NDSHA and PSHA maps in terms of average rates of exceedance for specified time windows. The comparison of NDSHA and PSHA maps, particularly for very long recurrence times, may indicate to what extent probabilistic ground shaking estimates are consistent with those from physical models of seismic waves propagation. A systematic comparison over the territory of Italy is carried out exploiting the uniqueness of the Italian earthquake catalogue, a data set covering more than a millennium (a time interval about ten times longer than that available in most of the regions worldwide) with a satisfactory completeness level for M>5, which warrants the results of analysis. By analysing in some detail seismicity in the Vrancea region, we show that well constrained macroseismic field information for individual earthquakes may provide useful information about the reliability of ground shaking estimates. Finally, in order to generalise observations, the comparative analysis is extended to further regions where both standard NDSHA and PSHA maps are available (e.g. State of Gujarat, India). The final Global Seismic Hazard Assessment Program (GSHAP) results and the most recent version of Seismic Hazard Harmonization in Europe (SHARE) project maps, along with other national scale probabilistic maps, all obtained by PSHA, are considered for this comparative analysis.

Three-dimensional (3D) evaluation of liquid distribution in shake flask using an optical fluorescence technique.

PubMed

Azizan, Amizon; Büchs, Jochen

2017-01-01

Biotechnological development in shake flask necessitates vital engineering parameters e.g. volumetric power input, mixing time, gas liquid mass transfer coefficient, hydromechanical stress and effective shear rate. Determination and optimization of these parameters through experiments are labor-intensive and time-consuming. Computational Fluid Dynamics (CFD) provides the ability to predict and validate these parameters in bioprocess engineering. This work provides ample experimental data which are easily accessible for future validations to represent the hydrodynamics of the fluid flow in the shake flask. A non-invasive measuring technique using an optical fluorescence method was developed for shake flasks containing a fluorescent solution with a waterlike viscosity at varying filling volume (V L  = 15 to 40 mL) and shaking frequency ( n  = 150 to 450 rpm) at a constant shaking diameter (d o  = 25 mm). The method detected the leading edge (LB) and tail of the rotating bulk liquid (TB) relative to the direction of the centrifugal acceleration at varying circumferential heights from the base of the shake flask. The determined LB and TB points were translated into three-dimensional (3D) circumferential liquid distribution plots. The maximum liquid height (H max ) of the bulk liquid increased with increasing filling volume and shaking frequency of the shaking flask, as expected. The toroidal shapes of LB and TB are clearly asymmetrical and the measured TB differed by the elongation of the liquid particularly towards the torus part of the shake flask. The 3D liquid distribution data collected at varying filling volume and shaking frequency, comprising of LB and TB values relative to the direction of the centrifugal acceleration are essential for validating future numerical solutions using CFD to predict vital engineering parameters in shake flask.

An Overview and Parametric Evaluation of the CGS ShakeMap Automated System in CISN

NASA Astrophysics Data System (ADS)

Hagos, L. Z.; Haddadi, H. R.; Shakal, A. F.

2014-12-01

In the recent years, ShakeMap has been extensively used in California for earthquake rapid response. Serving as a backup to the Northern and Southern seismic regions of the California Integrated Seismic Network (CISN), the California Geological Survey (CGS) is running a ShakeMap system configured such that it effectively produces ShakeMaps for earthquakes occurring in both regions. In achieving this goal, CGS has worked to improve the robustness of its ShakeMap system and the quality of its products. Peak ground motion amplitude data are exchanged between the CISN data centers to provide robust generation of ShakeMap. Most exchanged ground motion packets come associated with an earthquake by the authoritative network. However, for ground motion packets that come unassociated, CGS employs an event association scheme to associate them with the corresponding earthquake. The generated ShakeMap products are published to the CGS server which can also be accessed through the CISN website. The backup function is designed to publish ShakeMap products to the USGS NEIC server without collision with the regional networks, only acting in cases where the authoritative region encounters a system failure. Depending on the size, location and significance of the earthquake, review of ShakeMap products by a seismologist may involve changes to ShakeMap parameters from the default. We present an overview of the CGS ShakeMap system and highlight some of the parameters a seismologist may adjust including parameters related to basin effects, directivity effects when finite fault models are available, site corrections, etc. We also analyze the sensitivity and dependence of the ShakeMap intensity and ground motion maps on the number of observed data included in the computation. In light of the available strong motion amplitude data, we attempt to address the question of what constitutes an adequate quality ShakeMap in the tradeoff between rapidity and completeness. We also present a brief comparative study of the available Ground Motion to Intensity Conversion Equations (GMICE) by studying selected earthquakes in California region. Results of these studies can be used as a tool in ShakeMap generation for California earthquakes when the use of non-default parameters is required.

Application of laser scanning technique in earthquake protection of Istanbul's historical heritage buildings

NASA Astrophysics Data System (ADS)

Çaktı, Eser; Ercan, Tülay; Dar, Emrullah

2017-04-01

Istanbul's vast historical and cultural heritage is under constant threat of earthquakes. Historical records report repeated damages to the city's landmark buildings. Our efforts towards earthquake protection of several buildings in Istanbul involve earthquake monitoring via structural health monitoring systems, linear and non-linear structural modelling and analysis in search of past and future earthquake performance, shake-table testing of scaled models and non-destructive testing. More recently we have been using laser technology in monitoring structural deformations and damage in five monumental buildings which are Hagia Sophia Museum and Fatih, Sultanahmet, Süleymaniye and Mihrimah Sultan Mosques. This presentation is about these efforts with special emphasis on the use of laser scanning in monitoring of edifices.

Maybe Some Big Ground Shakes One Hundred Years Ago in a Big State Near the Ocean Were Caused by People

NASA Astrophysics Data System (ADS)

Hough, S. E.; Tsai, V. C.; Walker, R.; Page, M. T.; Aminzadeh, F.

2016-12-01

Sometimes people put water deep into the ground to make it go away and sometimes this causes the ground to shake. Sometimes people take other stuff out of the ground because a lot of people buy this stuff to power cars. Usually when people take this stuff out of the ground it does not cause ground shakes. At least this is what we used to believe. For our study, we looked at ground shakes that caused houses to fall down almost 100 years ago in a big state near the water. They were large ground shakes. One was close to a big city where people make movies and one was a really big shake in another city in the same state. We asked the question, is it possible that these ground shakes happened because people took stuff out of the ground? We considered the places where the ground shakes happened and the places where people took a lot of stuff out of the ground. We show there is a pretty good chance that taking stuff out of the ground caused some pretty big ground shakes. We explain how ground shakes can happen when people take stuff out of the ground. Ground shakes happen on things called faults. When you take stuff out of the ground, usually that makes it harder for the fault to move. This is a good thing. But when the stuff is still deep under the ground, sometimes it also pushes against faults that are close by and helps keep them from moving. So when you take stuff out, it does not push on faults as much, and so sometimes that close-by fault can move and cause ground shakes. We use a computer to show that our idea can explain some of what we see. The idea is not perfect but we think it is a pretty good idea. Our idea explains why it does not usually cause ground shakes when people take stuff out of the ground, but sometimes big ground shakes happen. Our idea suggests that ground shakes caused by people can sometimes be very large. So if people take stuff out of the ground or put stuff in the ground, they need to know if there are faults close by.

Speak Simply When Warning About After Shocks

NASA Astrophysics Data System (ADS)

Michael, A. J.; Hardebeck, J.; Page, M. T.; van der Elst, N.; Wein, A. M.

2016-12-01

When a fault in the ground slips, the ground moves fast and can shake hard. After a big ground shake, there are more shakes. We call them after shocks and these can happen over a long time, for many years. An after shock can shake the ground more than it shook the first time. These shocks can shake and break places where people live and work, make rocks fall down and the ground go soft and wet, and hurt or kill people. After shocks also make people worry. If people are scared, then they may leave the area and not come back. To help people be safe and feel calm we want to tell them what may happen. We often use big words and lots of numbers to give the chances for the number of shakes over days, weeks, and years. That helps some people fix things and do their jobs such as those who work on roads, power, water, phones, hospitals, schools or in the money business. But big words and too many numbers can confuse a lot of people and make them worry more. Studies of talking about the ground shake problem show that it is best to speak simply to people. What if we only use the ten hundred most often used words to talk about these ground shakes. Would that work? Here is a possible warning: Last week's huge ground shake will probably make more ground shakes. This week expect to feel three to ten ground shakes and maybe one big ground shake that could break things. That big ground shake has a chance of 1 in 10. This is normal. Be safe. Stay out of broken houses, shops, and work places. When you feel the ground shake: drop, cover, and hold on. People may feel afraid or be hurt, so check on friends and family. Get some more food and water. Over time there will be fewer ground shakes, but always be ready for them. That warning gives a lot of key ideas: what may happen, whether houses could get broken, that what is happening is normal, and what people may feel and should do. These are the key parts of a good warning. Maybe we should use the most often used words all the time.

Comparison of NASTRAN analysis with ground vibration results of UH-60A NASA/AEFA test configuration

NASA Technical Reports Server (NTRS)

Idosor, Florentino; Seible, Frieder

1990-01-01

Preceding program flight tests, a ground vibration test and modal test analysis of a UH-60A Black Hawk helicopter was conducted by Sikorsky Aircraft to complement the UH-60A test plan and NASA/ARMY Modern Technology Rotor Airloads Program. The 'NASA/AEFA' shake test configuration was tested for modal frequencies and shapes and compared with its NASTRAN finite element model counterpart to give correlative results. Based upon previous findings, significant differences in modal data existed and were attributed to assumptions regarding the influence of secondary structure contributions in the preliminary NASTRAN modeling. An analysis of an updated finite element model including several secondary structural additions has confirmed that the inclusion of specific secondary components produces a significant effect on modal frequency and free-response shapes and improves correlations at lower frequencies with shake test data.

[Comparison of techniques for coliform bacteria extraction from sediment of Xochimilco Lake, Mexico].

PubMed

Fernández-Rendón, Carlos L; Barrera-Escorcia, Guadalupe

2013-01-01

The need to separate bacteria from sediment in order to appropriately count them has led to test the efficacy of different techniques. In this research, traditional techniques such as manual shaking, homogenization, ultrasonication, and surfactant are compared. Moreover, the possibility of using a set of enzymes (pancreatine) and an antibiotic (ampicillin) for sediment coliform extraction is proposed. Samples were obtained from Xochimilco Lake in Mexico City. The most probable number of coliform bacteria was determined after applying the appropriate separation procedure. Most of the techniques tested led to numbers similar to those of the control (manual shaking). Only with the use of ampicillin, a greater total coliform concentration was observed (Mann-Whitney, z = 2.09; p = 0.03). It is possible to propose the use of ampicillin as a technique for total coliform extraction; however, it is necessary to consider sensitivity of bacteria to the antibiotic.

A reliable simultaneous representation of seismic hazard and of ground shaking recurrence

NASA Astrophysics Data System (ADS)

Peresan, A.; Panza, G. F.; Magrin, A.; Vaccari, F.

2015-12-01

Different earthquake hazard maps may be appropriate for different purposes - such as emergency management, insurance and engineering design. Accounting for the lower occurrence rate of larger sporadic earthquakes may allow to formulate cost-effective policies in some specific applications, provided that statistically sound recurrence estimates are used, which is not typically the case of PSHA (Probabilistic Seismic Hazard Assessment). We illustrate the procedure to associate the expected ground motions from Neo-deterministic Seismic Hazard Assessment (NDSHA) to an estimate of their recurrence. Neo-deterministic refers to a scenario-based approach, which allows for the construction of a broad range of earthquake scenarios via full waveforms modeling. From the synthetic seismograms the estimates of peak ground acceleration, velocity and displacement, or any other parameter relevant to seismic engineering, can be extracted. NDSHA, in its standard form, defines the hazard computed from a wide set of scenario earthquakes (including the largest deterministically or historically defined credible earthquake, MCE) and it does not supply the frequency of occurrence of the expected ground shaking. A recent enhanced variant of NDSHA that reliably accounts for recurrence has been developed and it is applied to the Italian territory. The characterization of the frequency-magnitude relation can be performed by any statistically sound method supported by data (e.g. multi-scale seismicity model), so that a recurrence estimate is associated to each of the pertinent sources. In this way a standard NDSHA map of ground shaking is obtained simultaneously with the map of the corresponding recurrences. The introduction of recurrence estimates in NDSHA naturally allows for the generation of ground shaking maps at specified return periods. This permits a straightforward comparison between NDSHA and PSHA maps.

Relation of landslides triggered by the Kiholo Bay earthquake to modeled ground motion

USGS Publications Warehouse

Harp, Edwin L.; Hartzell, Stephen H.; Jibson, Randall W.; Ramirez-Guzman, L.; Schmitt, Robert G.

2014-01-01

The 2006 Kiholo Bay, Hawaii, earthquake triggered high concentrations of rock falls and slides in the steep canyons of the Kohala Mountains along the north coast of Hawaii. Within these mountains and canyons a complex distribution of landslides was triggered by the earthquake shaking. In parts of the area, landslides were preferentially located on east‐facing slopes, whereas in other parts of the canyons no systematic pattern prevailed with respect to slope aspect or vertical position on the slopes. The geology within the canyons is homogeneous, so we hypothesize that the variable landslide distribution is the result of localized variation in ground shaking; therefore, we used a state‐of‐the‐art, high‐resolution ground‐motion simulation model to see if it could reproduce the landslide‐distribution patterns. We used a 3D finite‐element analysis to model earthquake shaking using a 10 m digital elevation model and slip on a finite‐fault model constructed from teleseismic records of the mainshock. Ground velocity time histories were calculated up to a frequency of 5 Hz. Dynamic shear strain also was calculated and compared with the landslide distribution. Results were mixed for the velocity simulations, with some areas showing correlation of landslide locations with peak modeled ground motions but many other areas showing no such correlation. Results were much improved for the comparison with dynamic shear strain. This suggests that (1) rock falls and slides are possibly triggered by higher frequency ground motions (velocities) than those in our simulations, (2) the ground‐motion velocity model needs more refinement, or (3) dynamic shear strain may be a more fundamental measurement of the decoupling process of slope materials during seismic shaking.

Comparisons of Low-Strain Amplification at Soft-Sediment, Hard-Rock, Topographic, and Fault-Zone Sites in the Hayward Fault Zone, California

NASA Astrophysics Data System (ADS)

Catchings, R.; Strayer, L. M.; Goldman, M.

2014-12-01

We used a temporary network of approximately 600 seismographs to record a seismic source generated by the collapse of a 13-story building near the active trace of the Hayward Fault. These data allow us to evaluate variations in ground shaking across a series of 30 2-km-long radial arrays centered on the seismic source. Individual seismographs were spaced at 200-m intervals, forming a series of 360°concentric arrays around the seismic source. The data show variations in amplification caused by (1) soft sediments within the East Bay alluvial plain (EBAP), (2) hard rocks within the East Bay hills (EBH), (3) low-velocity rocks within the Hayward Fault zone (HFZ), and (4) topography. Given that ground shaking varies strongly with distance from the source, the concentric arrays allowed us to measure variations in ground shaking as a function of azimuth at fixed distances from the source. On individual linear profiles within the concentric arrays, we observed decreases in peak ground velocity (PGV) across the HFZ and other faults within the EBH. However, for a given distance from the source, we observe four to five fold amplification from the EBAP sites compared to most sites in the EBH. Topographic and fault-zone amplification effects within the EBH, however, are greater than the EBAP sediment amplification. Thus, for future earthquakes, shaking at many sites within the EBH may be significantly stronger than many sites within the EBAP. These observations suggest amplification can be expected in unconsolidated sediments, but topographic and fault-zone amplification can be larger. This confirms the importance of site effects for hazard mitigation and in interpreting MMI for future and historical earthquakes.

Altered hypothalamic response to food in smokers123

PubMed Central

Geha, Paul Y; Aschenbrenner, Katja; Felsted, Jennifer; O'Malley, Stephanie S; Small, Dana M

2013-01-01

Background: Smoking cessation is often followed by weight gain. Eating behaviors and weight change have been linked to the brain response to food, but it is unknown whether smoking influences this response. Objective: We determined the influence of smoking status (smokers compared with nonsmokers) on the brain response to food in regions associated with weight changes in nonsmokers. Design: In study 1, we used functional MRI (fMRI) to identify regions of the brain associated with weight change in nonsmokers. BMI and the brain response to a milk shake, which is a palatable and energy-dense food, were measured in a group of 27 nonsmokers (5 men). Sixteen subjects (3 men) returned 1 y later for BMI reassessment. The change in BMI was regressed against the brain response to isolate regions associated with weight change. In study 2, to determine whether smokers showed altered responses in regions associated with weight change, we assessed the brain response to a milk shake in 11 smokers. The brain response to a milk shake compared with a tasteless control solution was assessed in 11 smokers (5 men) in comparison with a group of age-, sex- and body weight–matched nonsmokers selected from the pool of nonsmokers who participated in study 1. Results: The response in the midbrain, hypothalamus, thalamus, and ventral striatum was positively associated with weight change at the 1-y follow-up in 16 nonsmokers. Compared with nonsmokers, smokers had a greater response to milk shakes in the hypothalamus. Conclusion: Smokers display an altered brain response to food in the hypothalamus, which is an area associated with long-term weight change in nonsmokers. PMID:23235196

Spectral comparisons of sunlight and different lamps

NASA Technical Reports Server (NTRS)

Deitzer, Gerald

1994-01-01

The tables in this report were compiled to characterize the spectra of available lamp types and provide comparison to the spectra of sunlight. Table 1 reports the spectral distributions for various lamp sources and compares them to those measured for sunlight. Table 2 provides the amount of energy in Wm(exp -2) relative to the number of photons of PAR (photosynthetically active radiation) (400-700 nm) for each light source.

Graphical displays for effective reporting of evidence quality tables in research syntheses.

PubMed

Mignini, Luciano; Champaneria, Rita; Mishanina, Ekaterina; Khan, Khalid S

2016-03-09

When generating guidelines, quality of the evidence is tabulated to capture its several domains, often using the GRADE (Grading of Recommendations Assessment, Development and Evaluation) approach. We developed a graphic display to capture deficiencies, outliers and similarities across comparisons contained in GRADE tables. Based on a systematic literature review capturing the effects of 32 different therapeutic comparisons on dysmenorrhoea, we synthesised evidence quality in tables and graphs. We evaluated time taken to accurately assess evident quality and preference for tables vs. graphs. The plots provided visually striking displays of strengths and weaknesses of the evidence across the spectrum of comparisons on a single page. Equivalent tabulated information spread over 4 pages. Participants preferred and interpreted graphs quicker and more accurately than tables. The graphic approach we developed makes interpreting evidence easier. Large tables are dry and cumbersome to read and assimilate. When guideline statements are accompanied by these plots, they have the scope for improving the credibility of the recommendations made, as the strength of the evidence used can be clearly seen. Further empirical research will establish the place for graphic displays.

A new wireless system for decentralised measurement of physiological parameters from shake flasks

PubMed Central

Vasala, Antti; Panula, Johanna; Bollók, Monika; Illmann, Lutz; Hälsig, Christian; Neubauer, Peter

2006-01-01

Background Shake flasks are widely used because of their low price and simple handling. Many researcher are, however, not aware of the physiological consequences of oxygen limitation and substrate overflow metabolism that occur in shake flasks. Availability of a wireless measuring system brings the possibilities for quality control and design of cultivation conditions. Results Here we present a new wireless solution for the measurement of pH and oxygen from shake flasks with standard sensors, which allows data transmission over a distance of more than 100 metres in laboratory environments. This new system was applied to monitoring of cultivation conditions in shake flasks. The at-time monitoring of the growth conditions became possible by simple means. Here we demonstrate that with typical protocols E. coli shake flask cultures run into severe oxygen limitation and the medium is strongly acidified. Additionally the strength of the new system is demonstrated by continuous monitoring of the oxygen level in methanol-fed Pichia pastoris shake flask cultures, which allows the optimisation of substrate feeding for preventing starvation or methanol overfeed. 40 % higher cell density was obtained by preventing starvation phases which occur in standard shake flask protocols by adding methanol when the respiration activity decreased in the cultures. Conclusion The here introduced wireless system can read parallel sensor data over long distances from shake flasks that are under vigorous shaking in cultivation rooms or closed incubators. The presented technology allows centralised monitoring of decentralised targets. It is useful for the monitoring of pH and dissolved oxygen in shake flask cultures. It is not limited to standard sensors, but can be easily adopted to new types of sensors and measurement places (e.g., new sensor points in large-scale bioreactors). PMID:16504107

Diversity of head shaking nystagmus in peripheral vestibular disease.

PubMed

Kim, Min-Beom; Huh, Se Hyung; Ban, Jae Ho

2012-06-01

To evaluate the characteristics of head shaking nystagmus in various peripheral vestibular diseases. Retrospective case series. Tertiary referral center. Data of 235 patients with peripheral vestibular diseases including vestibular neuritis, Ménière's disease, and benign paroxysmal positional vertigo, were retrospectively analyzed. All subjects presented between August 2009 and July 2010. Patients were tested for vestibular function including head shaking nystagmus and caloric information. Regarding vestibular neuritis, all tests were again performed during the 1-month follow-up. Head shaking nystagmus was classified as monophasic or biphasic and, according to the affected ear, was divided as ipsilesional or contralesional. Of the 235 patients, 87 patients revealed positive head shaking nystagmus. According to each disease, positive rates of head shaking nystagmus were as follows: 35 (100%) of 35 cases of vestibular neuritis, 11 (68.8%) of 16 cases of Ménière's disease, and 41 (22.2%) of 184 cases of benign paroxysmal positional vertigo. All cases of vestibular neuritis initially presented as a monophasic, contralesional beating, head shaking nystagmus. However, 1 month after first visit, the direction of nystagmus was changed to biphasic (contralesional first then ipsilesional beating) in 25 cases (72.5%) but not in 10 cases (27.5%). There was a significant correlation between the degree of initial caloric weakness and the biphasic conversion of head shaking nystagmus (p = 0.02). In 72.5% of vestibular neuritis cases, head shaking nystagmus was converted to biphasic during the subacute period. The larger the initial canal paresis was present, the more frequent the biphasic conversion of head shaking nystagmus occurred. However, Ménière's disease and benign paroxysmal positional vertigo did not have specific patterns of head shaking nystagmus.

High resolution measurement of earthquake impacts on rock slope stability and damage using pre- and post-earthquake terrestrial laser scans

NASA Astrophysics Data System (ADS)

Hutchinson, Lauren; Stead, Doug; Rosser, Nick

2017-04-01

Understanding the behaviour of rock slopes in response to earthquake shaking is instrumental in response and relief efforts following large earthquakes as well as to ongoing risk management in earthquake affected areas. Assessment of the effects of seismic shaking on rock slope kinematics requires detailed surveys of the pre- and post-earthquake condition of the slope; however, at present, there is a lack of high resolution monitoring data from pre- and post-earthquake to facilitate characterization of seismically induced slope damage and validate models used to back-analyze rock slope behaviour during and following earthquake shaking. Therefore, there is a need for additional research where pre- and post- earthquake monitoring data is available. This paper presents the results of a direct comparison between terrestrial laser scans (TLS) collected in 2014, the year prior to the 2015 earthquake sequence, with that collected 18 months after the earthquakes and two monsoon cycles. The two datasets were collected using Riegl VZ-1000 and VZ-4000 full waveform laser scanners with high resolution (c. 0.1 m point spacing as a minimum). The scans cover the full landslide affected slope from the toe to the crest. The slope is located in Sindhupalchok District, Central Nepal which experienced some of the highest co-seismic and post-seismic landslide intensities across Nepal due to the proximity to the epicenters (<20 km) of both of the main aftershocks on April 26, 2015 (M 6.7) and May 12, 2015 (M7.3). During the 2015 earthquakes and subsequent 2015 and 2016 monsoons, the slope experienced rockfall and debris flows which are evident in satellite imagery and field photographs. Fracturing of the rock mass associated with the seismic shaking is also evident at scales not accessible through satellite and field observations. The results of change detection between the TLS datasets with an emphasis on quantification of seismically-induced slope damage is presented. Patterns in the distribution and expression of rock mass damage are also explored. The findings presented herein provide insight into the response of rock slopes to seismic shaking and highlight the application of remote sensing to understand slope behaviour.

Insights into earthquake hazard map performance from shaking history simulations

NASA Astrophysics Data System (ADS)

Stein, S.; Vanneste, K.; Camelbeeck, T.; Vleminckx, B.

2017-12-01

Why recent large earthquakes caused shaking stronger than predicted by earthquake hazard maps is under debate. This issue has two parts. Verification involves how well maps implement probabilistic seismic hazard analysis (PSHA) ("have we built the map right?"). Validation asks how well maps forecast shaking ("have we built the right map?"). We explore how well a map can ideally perform by simulating an area's shaking history and comparing "observed" shaking to that predicted by a map generated for the same parameters. The simulations yield shaking distributions whose mean is consistent with the map, but individual shaking histories show large scatter. Infrequent large earthquakes cause shaking much stronger than mapped, as observed. Hence, PSHA seems internally consistent and can be regarded as verified. Validation is harder because an earthquake history can yield shaking higher or lower than that predicted while being consistent with the hazard map. The scatter decreases for longer observation times because the largest earthquakes and resulting shaking are increasingly likely to have occurred. For the same reason, scatter is much less for the more active plate boundary than for a continental interior. For a continental interior, where the mapped hazard is low, even an M4 event produces exceedances at some sites. Larger earthquakes produce exceedances at more sites. Thus many exceedances result from small earthquakes, but infrequent large ones may cause very large exceedances. However, for a plate boundary, an M6 event produces exceedance at only a few sites, and an M7 produces them in a larger, but still relatively small, portion of the study area. As reality gives only one history, and a real map involves assumptions about more complicated source geometries and occurrence rates, which are unlikely to be exactly correct and thus will contribute additional scatter, it is hard to assess whether misfit between actual shaking and a map — notably higher-than-mapped shaking — arises by chance or reflects biases in the map. Due to this problem, there are limits to how well we can expect hazard maps to predict future shaking, as well as to our ability to test the performance of a hazard map based on available observations.

Development and utilization of USGS ShakeCast for rapid post-earthquake assessment of critical facilities and infrastructure

USGS Publications Warehouse

Wald, David J.; Lin, Kuo-wan; Kircher, C.A.; Jaiswal, Kishor; Luco, Nicolas; Turner, L.; Slosky, Daniel

2017-01-01

The ShakeCast system is an openly available, near real-time post-earthquake information management system. ShakeCast is widely used by public and private emergency planners and responders, lifeline utility operators and transportation engineers to automatically receive and process ShakeMap products for situational awareness, inspection priority, or damage assessment of their own infrastructure or building portfolios. The success of ShakeCast to date and its broad, critical-user base mandates improved software usability and functionality, including improved engineering-based damage and loss functions. In order to make the software more accessible to novice users—while still utilizing advanced users’ technical and engineering background—we have developed a “ShakeCast Workbook”, a well documented, Excel spreadsheet-based user interface that allows users to input notification and inventory data and export XML files requisite for operating the ShakeCast system. Users will be able to select structure based on a minimum set of user-specified facility (building location, size, height, use, construction age, etc.). “Expert” users will be able to import user-modified structural response properties into facility inventory associated with the HAZUS Advanced Engineering Building Modules (AEBM). The goal of the ShakeCast system is to provide simplified real-time potential impact and inspection metrics (i.e., green, yellow, orange and red priority ratings) to allow users to institute customized earthquake response protocols. Previously, fragilities were approximated using individual ShakeMap intensity measures (IMs, specifically PGA and 0.3 and 1s spectral accelerations) for each facility but we are now performing capacity-spectrum damage state calculations using a more robust characterization of spectral deamnd.We are also developing methods for the direct import of ShakeMap’s multi-period spectra in lieu of the assumed three-domain design spectrum (at 0.3s for constant acceleration; 1s or 3s for constant velocity and constant displacement at very long response periods). As part of ongoing ShakeCast research and development, we will also explore the use of ShakeMap IM uncertainty estimates and evaluate the assumption of employing multiple response spectral damping values rather than the single 5%-damped value currently employed. Developing and incorporating advanced fragility assignments into the ShakeCast Workbook requires related software modifications and database improvements; these enhancements are part of an extensive rewrite of the ShakeCast application.

Saugus River and Tributaries Flood Damage Reduction Study: Lynn, Malden, Revere and Saugus, Massachusetts. Section 1. Feasibility Report.

DTIC Science & Technology

1989-12-01

57 Table 5 Sensitivity Analysis - Point of Pines LPP 61 Table 6 Plan Comparison 64 Table 7 NED Plan Project Costs 96 Table 8 Estimated Operation...Costs 99 Table 13 Selected Plan/Estimated Annual Benefits 101 Table 14 Comparative Impacts - NED Regional Floodgate Plan 102 Table 15 Economic Analysis ...Includes detailed descriptions, plans and profiles and design considerations of the selected plan; coastal analysis of the shorefront; detailed project

Association of adverse childhood experiences with shaking and smothering behaviors among Japanese caregivers.

PubMed

Isumi, Aya; Fujiwara, Takeo

2016-07-01

Shaking and smothering in response to infant crying are life-threatening child abuse. Parental childhood abuse history is known to be one of the most robust risk factors for abusing their offspring. In addition to childhood abuse history, other adverse childhood exposures (ACEs) need to be considered due to co-occurrence. However, few studies have investigated the impact of ACEs on caregivers shaking and smothering their infant. This study aims to investigate the association of ACEs with shaking and smothering among caregivers of infants in Japan. A questionnaire was administered to caregivers participating in a four-month health checkup between September 2013 and August 2014 in Chiba City, Japan, to assess their ACEs (parental death, parental divorce, mentally ill parents, witness of intimate partner violence, physical abuse, neglect, psychological abuse and economic hardship), and shaking and smothering toward their infants (N=4297). Logistic regression analysis was used to examine the cumulative and individual impacts of ACEs on shaking and smothering. Analyses were conducted in 2015. A total of 28.3% reported having experienced at least one ACE during their childhood. We found that only witness of IPV had a significant association with shaking of infant (OR=1.93, 95% CI: 1.03-3.61). The total number of ACEs was not associated with either shaking or smothering. Our findings suggest that shaking and smothering in response to crying can occur regardless of ACEs. Population-based strategies that target all caregivers to prevent shaking and smothering of infants are needed. Copyright © 2016 Elsevier Ltd. All rights reserved.

Ring Shake in Eastern Hemlock: Frequency and Relationship to Tree Attributes

Treesearch

John E. Baumgras; Paul E. Sendak; David L. Sonderman; David L. Sonderman

2000-01-01

Ring shake is a barrier to improved utilization of eastern hemlock, an important component of the total softwood timber resource in the Eastern United States and Canada. Ring shake is the lengthwise separation of wood that occurs between and parallel to growth rings, diminishing lumber yields and values. Evaluating the potential for ring shake is essential to improving...

Ring shake in eastern hemlock: frequency and relationship to tree attributes

Treesearch

John E. Baumgras; Paul E. Sendak; David L. Sonderman

2000-01-01

Ring shake is a barrier to improved utilization of eastern hemlock, an important component of the total softwood timber resource in the Eastern United States and Canada. Ring shake is the lengthwise separation of wood that occurs between and parallel to growth rings, diminishing lumber yields and values. Evaluating the potential for ring shake is essential to improving...

Radial shakes and "frost cracks" in living oak trees

Treesearch

Heinz Butin; Alex L. Shigo

1981-01-01

Dissections of hundreds of living, mature oak trees over a 25-year period revealed that radial shakes (or "frost cracks") and ring shakes are associated with a variety of wounds and stubs of branches and basal sprouts. A more intensive study of radial shakes that included dissections of more than 30 oaks confirmed the earlier finds, and provided additional...

An Orientation Sensor-Based Head Tracking System for Driver Behaviour Monitoring.

PubMed

Zhao, Yifan; Görne, Lorenz; Yuen, Iek-Man; Cao, Dongpu; Sullman, Mark; Auger, Daniel; Lv, Chen; Wang, Huaji; Matthias, Rebecca; Skrypchuk, Lee; Mouzakitis, Alexandros

2017-11-22

Although at present legislation does not allow drivers in a Level 3 autonomous vehicle to engage in a secondary task, there may become a time when it does. Monitoring the behaviour of drivers engaging in various non-driving activities (NDAs) is crucial to decide how well the driver will be able to take over control of the vehicle. One limitation of the commonly used face-based head tracking system, using cameras, is that sufficient features of the face must be visible, which limits the detectable angle of head movement and thereby measurable NDAs, unless multiple cameras are used. This paper proposes a novel orientation sensor based head tracking system that includes twin devices, one of which measures the movement of the vehicle while the other measures the absolute movement of the head. Measurement error in the shaking and nodding axes were less than 0.4°, while error in the rolling axis was less than 2°. Comparison with a camera-based system, through in-house tests and on-road tests, showed that the main advantage of the proposed system is the ability to detect angles larger than 20° in the shaking and nodding axes. Finally, a case study demonstrated that the measurement of the shaking and nodding angles, produced from the proposed system, can effectively characterise the drivers' behaviour while engaged in the NDAs of chatting to a passenger and playing on a smartphone.

Real-time Shakemap implementation in Austria

NASA Astrophysics Data System (ADS)

Weginger, Stefan; Jia, Yan; Papi Isaba, Maria; Horn, Nikolaus

2017-04-01

ShakeMaps provide near-real-time maps of ground motion and shaking intensity following significant earthquakes. They are automatically generated within a few minutes after occurrence of an earthquake. We tested and included the USGS ShakeMap 4.0 (experimental code) based on python in the Antelope real-time system with local modified GMPE and Site Effects based on the conditions in Austria. The ShakeMaps are provided in terms of Intensity, PGA, PGV and PSA. Future presentation of ShakeMap contour lines and Ground Motion Parameter with interactive maps and data exchange over Web-Services are shown.

Optimizing CyberShake Seismic Hazard Workflows for Large HPC Resources

NASA Astrophysics Data System (ADS)

Callaghan, S.; Maechling, P. J.; Juve, G.; Vahi, K.; Deelman, E.; Jordan, T. H.

2014-12-01

The CyberShake computational platform is a well-integrated collection of scientific software and middleware that calculates 3D simulation-based probabilistic seismic hazard curves and hazard maps for the Los Angeles region. Currently each CyberShake model comprises about 235 million synthetic seismograms from about 415,000 rupture variations computed at 286 sites. CyberShake integrates large-scale parallel and high-throughput serial seismological research codes into a processing framework in which early stages produce files used as inputs by later stages. Scientific workflow tools are used to manage the jobs, data, and metadata. The Southern California Earthquake Center (SCEC) developed the CyberShake platform using USC High Performance Computing and Communications systems and open-science NSF resources.CyberShake calculations were migrated to the NSF Track 1 system NCSA Blue Waters when it became operational in 2013, via an interdisciplinary team approach including domain scientists, computer scientists, and middleware developers. Due to the excellent performance of Blue Waters and CyberShake software optimizations, we reduced the makespan (a measure of wallclock time-to-solution) of a CyberShake study from 1467 to 342 hours. We will describe the technical enhancements behind this improvement, including judicious introduction of new GPU software, improved scientific software components, increased workflow-based automation, and Blue Waters-specific workflow optimizations.Our CyberShake performance improvements highlight the benefits of scientific workflow tools. The CyberShake workflow software stack includes the Pegasus Workflow Management System (Pegasus-WMS, which includes Condor DAGMan), HTCondor, and Globus GRAM, with Pegasus-mpi-cluster managing the high-throughput tasks on the HPC resources. The workflow tools handle data management, automatically transferring about 13 TB back to SCEC storage.We will present performance metrics from the most recent CyberShake study, executed on Blue Waters. We will compare the performance of CPU and GPU versions of our large-scale parallel wave propagation code, AWP-ODC-SGT. Finally, we will discuss how these enhancements have enabled SCEC to move forward with plans to increase the CyberShake simulation frequency to 1.0 Hz.

Using CyberShake Workflows to Manage Big Seismic Hazard Data on Large-Scale Open-Science HPC Resources

NASA Astrophysics Data System (ADS)

Callaghan, S.; Maechling, P. J.; Juve, G.; Vahi, K.; Deelman, E.; Jordan, T. H.

2015-12-01

The CyberShake computational platform, developed by the Southern California Earthquake Center (SCEC), is an integrated collection of scientific software and middleware that performs 3D physics-based probabilistic seismic hazard analysis (PSHA) for Southern California. CyberShake integrates large-scale and high-throughput research codes to produce probabilistic seismic hazard curves for individual locations of interest and hazard maps for an entire region. A recent CyberShake calculation produced about 500,000 two-component seismograms for each of 336 locations, resulting in over 300 million synthetic seismograms in a Los Angeles-area probabilistic seismic hazard model. CyberShake calculations require a series of scientific software programs. Early computational stages produce data used as inputs by later stages, so we describe CyberShake calculations using a workflow definition language. Scientific workflow tools automate and manage the input and output data and enable remote job execution on large-scale HPC systems. To satisfy the requests of broad impact users of CyberShake data, such as seismologists, utility companies, and building code engineers, we successfully completed CyberShake Study 15.4 in April and May 2015, calculating a 1 Hz urban seismic hazard map for Los Angeles. We distributed the calculation between the NSF Track 1 system NCSA Blue Waters, the DOE Leadership-class system OLCF Titan, and USC's Center for High Performance Computing. This study ran for over 5 weeks, burning about 1.1 million node-hours and producing over half a petabyte of data. The CyberShake Study 15.4 results doubled the maximum simulated seismic frequency from 0.5 Hz to 1.0 Hz as compared to previous studies, representing a factor of 16 increase in computational complexity. We will describe how our workflow tools supported splitting the calculation across multiple systems. We will explain how we modified CyberShake software components, including GPU implementations and migrating from file-based communication to MPI messaging, to greatly reduce the I/O demands and node-hour requirements of CyberShake. We will also present performance metrics from CyberShake Study 15.4, and discuss challenges that producers of Big Data on open-science HPC resources face moving forward.

Experimental Evaluation of a Device Prototype Based on Shape Memory Alloys for the Retrofit of Historical Buildings

NASA Astrophysics Data System (ADS)

Cardone, Donatello; Sofia, Salvatore

2012-12-01

Metallic tie-rods are currently used in many historical buildings for absorbing the out-of-plane horizontal forces of arches, vaults and roof trusses, despite they exhibit several limitations under service and seismic conditions. In this paper, a post-tensioned system based on the superelastic properties of Ni-Ti shape memory alloys is proposed for improving the structural performances of traditional metallic tie-rods. First, the thermal behavior under service conditions is investigated based on the results of numerical and experimental studies. Subsequently, the seismic performances under strong earthquakes are verified trough a number of shaking table tests on a 1:4-scale timber roof truss model. The outcomes of these studies fully confirm the achievement of the design objectives of the proposed prototype device.

9. EAST ELEVATION OF SKIDOO MILL, LOOKING WEST. THE LEVELS ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

9. EAST ELEVATION OF SKIDOO MILL, LOOKING WEST. THE LEVELS OF THE MILL CAN BE CLEARLY SEEN HERE. THE UPPER MOST LEVEL CONSISTS OF A CONVEORY THAT BROUGHT ORE TO A JAW CRUSHER. THE CRUSHED ORE WAS CHANNELED DIRECTLY INTO A LARGE ORE BIN LOCATED BEHIND THE COVERED WALL (CENTER). THE NEXT LEVEL SHOWS THE BULL (DRIVE) WHEEL ON THE UPPER PART OF THE STAMP BATTERIES. THE NEXT LEVEL DOWN (STAIRS) IS THE LOWER PORTION OF THE STAMP BATTERIES WITH THE MORTAR BLOCKS AND APRONS. THE NEXT LEVEL DOWN (LOWER RIGHT) HELD CONCENTRATION (SHAKING) TABLES AND A CLASSIFIER. MOST EXTERIOR WALL COVERING, TIMBERS, AND ROOF IS MISSING FROM THE MILL. SEE CA-290-42 (CT) FOR IDENTICAL COLOR TRANSPARENCY - Skidoo Mine, Park Route 38 (Skidoo Road), Death Valley Junction, Inyo County, CA

42. EAST ELEVATION OF SKIDOO MILL, LOOKING WEST. THE LEVELS ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

42. EAST ELEVATION OF SKIDOO MILL, LOOKING WEST. THE LEVELS OF THE MILL CAN BE CLEARLY SEEN HERE. THE UPPER MOST LEVEL CONSISTS OF A CONVEORY THAT BROUGHT ORE TO A JAW CRUSHER. THE CRUSHED ORE WAS CHANNELED DIRECTLY INTO A LARGE ORE BIN LOCATED BEHIND THE COVERED WALL (CENTER). THE NEXT LEVEL SHOWS THE BULL (DRIVE) WHEEL ON THE UPPER PART OF THE STAMP BATTERIES THE NEXT LEVEL DOWN (STAIRS) IS THE LOWER PORTION OF THE STAMP BATTERIES WITH MORTAR BLOCKS AND APRONS. THE NEXT LEVEL DOWN (LOWER RIGHT) HELD CONCENTRATION (SHAKING) TABLES AND A CLASSIFIER. MOST EXTERIOR WALL COVERING, TIMBERS, AND ROOF IS MISSING FROM THE MILL. SEE CA-290-9 FOR IDENTICAL B&W NEGATIVE. - Skidoo Mine, Park Route 38 (Skidoo Road), Death Valley Junction, Inyo County, CA

Macroscopic Neural Theories of Cognition

DTIC Science & Technology

2014-03-01

Autobiographical Memory -- 51% • Emotional Face Processing -- 14% • Single Word Reading -- 45% • N-Back Working Memory – 41% 22 A graphic comparison of...seven meta-analyses carried out for working memory is shown in Table 2. The results of this comparison were also clear—there was substantial...variation among the areas reported by the seven meta-analyses. Table 2. A Comparison of Seven Meta-analyses dealing with Working Memory . (Uttal, 2013

Combining Multiple Rupture Models in Real-Time for Earthquake Early Warning

NASA Astrophysics Data System (ADS)

Minson, S. E.; Wu, S.; Beck, J. L.; Heaton, T. H.

2015-12-01

The ShakeAlert earthquake early warning system for the west coast of the United States is designed to combine information from multiple independent earthquake analysis algorithms in order to provide the public with robust predictions of shaking intensity at each user's location before they are affected by strong shaking. The current contributing analyses come from algorithms that determine the origin time, epicenter, and magnitude of an earthquake (On-site, ElarmS, and Virtual Seismologist). A second generation of algorithms will provide seismic line source information (FinDer), as well as geodetically-constrained slip models (BEFORES, GPSlip, G-larmS, G-FAST). These new algorithms will provide more information about the spatial extent of the earthquake rupture and thus improve the quality of the resulting shaking forecasts.Each of the contributing algorithms exploits different features of the observed seismic and geodetic data, and thus each algorithm may perform differently for different data availability and earthquake source characteristics. Thus the ShakeAlert system requires a central mediator, called the Central Decision Module (CDM). The CDM acts to combine disparate earthquake source information into one unified shaking forecast. Here we will present a new design for the CDM that uses a Bayesian framework to combine earthquake reports from multiple analysis algorithms and compares them to observed shaking information in order to both assess the relative plausibility of each earthquake report and to create an improved unified shaking forecast complete with appropriate uncertainties. We will describe how these probabilistic shaking forecasts can be used to provide each user with a personalized decision-making tool that can help decide whether or not to take a protective action (such as opening fire house doors or stopping trains) based on that user's distance to the earthquake, vulnerability to shaking, false alarm tolerance, and time required to act.

Does knowledge signify protection? The SEISMOPOLIS centre for improvement of behavior in case of an earthquake

NASA Astrophysics Data System (ADS)

Dandoulaki, M.; Kourou, A.; Panoutsopoulou, M.

2009-04-01

It is vastly accepted that earthquake education is the way to earthquake protection. Nonetheless experience demonstrates that knowing what to do does not necessarily result in a better behaviour in case of a real earthquake. A research project titled: "Seismopolis" - "Pilot integrated System for Public Familiarization with Earthquakes and Information on Earthquake Protection" aimed at the improvement of the behaviour of people through an appropriate amalgamation of knowledge transfer and virtually experiencing an earthquake situation. Seismopolis combines well established education means such as books and leaflets with new technologies like earthquake simulation and virtual reality. It comprises a series of 5 main spaces that the visitor passes one-by-one. Space 1. Reception and introductory information. Visitors are given fundamental information on earthquakes and earthquake protection, as well as on the appropriate behaviour in case of an earthquake. Space 2. Earthquake simulation room Visitors experience an earthquake in a room. A typical kitchen is set on a shake table area (3m x 6m planar triaxial shake table) and is shaken in both horizontal and vertical directions by introducing seismographs of real or virtual earthquakes. Space 3. Virtual reality room Visitors may have the opportunity to virtually move around in the building or in the city after an earthquake disaster and take action as in a real-life situation, wearing stereoscopic glasses and using navigation tools. Space 4. Information and resources library Visitors are offered the opportunity to know more about earthquake protection. A series of means are available for this, some developed especially for Seismopolis (3 books, 2 Cds, a website and an interactive table game). Space 5. De-briefing area Visitors may be subjected to a pedagogical and psychological evaluation at the end of their visit and offered support if needed. For the evaluation of the "Seismopolis" Centre, a pilot application of the complete complex took place with the participation of different groups (schoolchildren, university students, adults, elderly persons, emigrants and persons with special needs). This test period recorded positive impression and reaction from the visitors and indicated the pedagogical and psychological appropriateness of the system. Seismopolis is the outcome of collaboration of public, academic and private partners and of a range of disciplines, namely seismologists, geologists, structural engineers, geographers, sociologists and psycologists. It is actually hosted by the Municipality of Rendis in Athens. More information on Seismopolis can be found in www.seismopolis.org .

Wood Shakes and Shingles for Roof Applications: Tips for Longer Life

Treesearch

Mark T. Knaebe

2013-01-01

Many wood shakes and shingles have been replaced by composition or asphalt-based shingles. Nevertheless, wood shakes and shingles are still widely used on commercial structures and residential houses.

Detection on vehicle vibration induced by the engine shaking based on the laser triangulation

NASA Astrophysics Data System (ADS)

Chen, Wenxue; Yang, Biwu; Ni, Zhibin; Hu, Xinhan; Han, Tieqiang; Hu, Yaocheng; Zhang, Wu; Wang, Yunfeng

2017-10-01

The magnitude of engine shaking is chosen to evaluate the vehicle performance. The engine shaking is evaluated by the vehicle vibration. Based on the laser triangulation, the vehicle vibration is measured by detecting the distance variation between the bodywork and road surface. The results represent the magnitude of engine shaking. The principle and configuration of the laser triangulation is also introduced in this paper.

ShakeMap manual: technical manual, user's guide, and software guide

USGS Publications Warehouse

Wald, David J.; Worden, Bruce C.; Quitoriano, Vincent; Pankow, Kris L.

2005-01-01

ShakeMap (http://earthquake.usgs.gov/shakemap) --rapidly, automatically generated shaking and intensity maps--combines instrumental measurements of shaking with information about local geology and earthquake location and magnitude to estimate shaking variations throughout a geographic area. The results are rapidly available via the Web through a variety of map formats, including Geographic Information System (GIS) coverages. These maps have become a valuable tool for emergency response, public information, loss estimation, earthquake planning, and post-earthquake engineering and scientific analyses. With the adoption of ShakeMap as a standard tool for a wide array of users and uses came an impressive demand for up-to-date technical documentation and more general guidelines for users and software developers. This manual is meant to address this need. ShakeMap, and associated Web and data products, are rapidly evolving as new advances in communications, earthquake science, and user needs drive improvements. As such, this documentation is organic in nature. We will make every effort to keep it current, but undoubtedly necessary changes in operational systems take precedence over producing and making documentation publishable.

The 2010-2011 Canterbury Earthquake Sequence: Environmental effects, seismic triggering thresholds and geologic legacy

NASA Astrophysics Data System (ADS)

Quigley, Mark C.; Hughes, Matthew W.; Bradley, Brendon A.; van Ballegooy, Sjoerd; Reid, Catherine; Morgenroth, Justin; Horton, Travis; Duffy, Brendan; Pettinga, Jarg R.

2016-03-01

Seismic shaking and tectonic deformation during strong earthquakes can trigger widespread environmental effects. The severity and extent of a given effect relates to the characteristics of the causative earthquake and the intrinsic properties of the affected media. Documentation of earthquake environmental effects in well-instrumented, historical earthquakes can enable seismologic triggering thresholds to be estimated across a spectrum of geologic, topographic and hydrologic site conditions, and implemented into seismic hazard assessments, geotechnical engineering designs, palaeoseismic interpretations, and forecasts of the impacts of future earthquakes. The 2010-2011 Canterbury Earthquake Sequence (CES), including the moment magnitude (Mw) 7.1 Darfield earthquake and Mw 6.2, 6.0, 5.9, and 5.8 aftershocks, occurred on a suite of previously unidentified, primarily blind, active faults in the eastern South Island of New Zealand. The CES is one of Earth's best recorded historical earthquake sequences. The location of the CES proximal to and beneath a major urban centre enabled rapid and detailed collection of vast amounts of field, geospatial, geotechnical, hydrologic, biologic, and seismologic data, and allowed incremental and cumulative environmental responses to seismic forcing to be documented throughout a protracted earthquake sequence. The CES caused multiple instances of tectonic surface deformation (≥ 3 events), surface manifestations of liquefaction (≥ 11 events), lateral spreading (≥ 6 events), rockfall (≥ 6 events), cliff collapse (≥ 3 events), subsidence (≥ 4 events), and hydrological (10s of events) and biological shifts (≥ 3 events). The terrestrial area affected by strong shaking (e.g. peak ground acceleration (PGA) ≥ 0.1-0.3 g), and the maximum distances between earthquake rupture and environmental response (Rrup), both generally increased with increased earthquake Mw, but were also influenced by earthquake location and source characteristics. However, the severity of a given environmental response at any given site related predominantly to ground shaking characteristics (PGA, peak ground velocities) and site conditions (water table depth, soil type, geomorphic and topographic setting) rather than earthquake Mw. In most cases, the most severe liquefaction, rockfall, cliff collapse, subsidence, flooding, tree damage, and biologic habitat changes were triggered by proximal, moderate magnitude (Mw ≤ 6.2) earthquakes on blind faults. CES environmental effects will be incompletely preserved in the geologic record and variably diagnostic of spatial and temporal earthquake clustering. Liquefaction feeder dikes in areas of severe and recurrent liquefaction will provide the best preserved and potentially most diagnostic CES features. Rockfall talus deposits and boulders will be well preserved and potentially diagnostic of the strong intensity of CES shaking, but challenging to decipher in terms of single versus multiple events. Most other phenomena will be transient (e.g., distal groundwater responses), not uniquely diagnostic of earthquakes (e.g., flooding), or more ambiguous (e.g. biologic changes). Preliminary palaeoseismic investigations in the CES region indicate recurrence of liquefaction in susceptible sediments of 100 to 300 yr, recurrence of severe rockfall event(s) of ca. 6000 to 8000 yr, and recurrence of surface rupturing on the largest CES source fault of ca. 20,000 to 30,000 yr. These data highlight the importance of utilising multiple proxy datasets in palaeoearthquake studies. The severity of environmental effects triggered during the strongest CES earthquakes was as great as or equivalent to any historic or prehistoric effects recorded in the geologic record. We suggest that the shaking caused by rupture of local blind faults in the CES comprised a 'worst case' seismic shaking scenario for parts of the Christchurch urban area. Moderate Mw blind fault earthquakes may contribute the highest proportion of seismic hazard, be the most important drivers of landscape evolution, and dominate the palaeoseismic record in some locations on Earth, including locations distal from any identified active faults. A high scientific priority should be placed on improving the spatial extent and quality of 'off-fault' shaking records of strong earthquakes, particularly near major urban centres.

In vitro tuberization of Chlorophytum Borivilianum Sant & Fern (Safed musli) as influenced by sucrose, CCC and culture systems.

PubMed

Farshad Ashraf, Mehdi; Abd Aziz, Maheran; Abdul Kadir, Mihdzar; Stanslas, Johnson; Farokhian, Elmira

2013-08-01

This study focuses on the establishment of in vitro tuberization of Chlorophytum borivilianum using solid and liquid culture systems. A high in vitro tuberization rate on solid and stationary liquid Murashige and Skoog media was observed in the presence of 60 g l⁻¹ sucrose with 950, 1,265 and 1,580 µM 2-chloroethyl-trimethylammonium chloride (CCC). Application of a higher sucrose concentration of 90 g l⁻¹ showed a negative interaction with CCC on in vitro tuber number and days to in vitro tuber induction. For economic feasibility, 950 µM CCC with 60 g l⁻¹ sucrose was chosen as the best combination for in vitro tuberization in both solid and stationary liquid media. For optimization of in vitro tuber production,a comparison between solid, stationary liquid and shake liquid culture was carried out. Liquid culture with shaking at 80 r.p.m. resulted in a >2.5-fold increase in in vitro tuber production compared with solid culture.

Next-Level ShakeZoning for Earthquake Hazard Definition in Nevada

NASA Astrophysics Data System (ADS)

Louie, J. N.; Savran, W. H.; Flinchum, B. A.; Dudley, C.; Prina, N.; Pullammanappallil, S.; Pancha, A.

2011-12-01

We are developing "Next-Level ShakeZoning" procedures tailored for defining earthquake hazards in Nevada. The current Federally sponsored tools- the USGS hazard maps and ShakeMap, and FEMA HAZUS- were developed as statistical summaries to match earthquake data from California, Japan, and Taiwan. The 2008 Wells and Mogul events in Nevada showed in particular that the generalized statistical approach taken by ShakeMap cannot match actual data on shaking from earthquakes in the Intermountain West, even to first order. Next-Level ShakeZoning relies on physics and geology to define earthquake shaking hazards, rather than statistics. It follows theoretical and computational developments made over the past 20 years, to capitalize on detailed and specific local data sets to more accurately model the propagation and amplification of earthquake waves through the multiple geologic basins of the Intermountain West. Excellent new data sets are now available for Las Vegas Valley. Clark County, Nevada has completed the nation's very first effort to map earthquake hazard class systematically through an entire urban area using Optim's SeisOpt° ReMi technique, which was adapted for large-scale data collection. Using the new Parcel Map in computing shaking in the Valley for scenario earthquakes is crucial for obtaining realistic predictions of ground motions. In an educational element of the project, a dozen undergraduate students have been computing 50 separate earthquake scenarios affecting Las Vegas Valley, using the Next-Level ShakeZoning process. Despite affecting only the upper 30 meters, the Vs30 geotechnical shear-velocity from the Parcel Map shows clear effects on 3-d shaking predictions computed so far at frequencies from 0.1 Hz up to 1.0 Hz. The effect of the Parcel Map on even the 0.1-Hz waves is prominent even with the large mismatch of wavelength to geotechnical depths. Amplifications and de-amplifications affected by the Parcel Map exceed a factor of two, and are highly dependent on the particular scenario. As well, Parcel Map amplification effects extend into areas not characterized in the Parcel Map. The fully 3-d Next-Level ShakeZoning scenarios show many areas of shaking amplification and de-amplification that USGS ShakeMap scenarios cannot predict. For example, the Frenchman Mountain scenario shows PGV of the two approaches within 15% of each other near the source, but upwards of 200% relative amplification or de-amplification, depending on location, throughout Las Vegas Valley.

Experimental studies of the effects of buffered particle dampers attached to a multi-degree-of-freedom system under dynamic loads

NASA Astrophysics Data System (ADS)

Lu, Zheng; Lu, Xilin; Lu, Wensheng; Masri, Sami F.

2012-04-01

This paper presents a systematic experimental investigation of the effects of buffered particle dampers attached to a multi-degree-of-freedom (mdof) system under different dynamic loads (free vibration, random excitation as well as real onsite earthquake excitations), and analytical/computational study of such a system. A series of shaking table tests of a three-storey steel frame with the buffered particle damper system are carried out to evaluate the performance and to verify the analysis method. It is shown that buffered particle dampers have good performance in reducing the response of structures under dynamic loads, especially under random excitation case. It can effectively control the fundamental mode of the mdof primary system; however, the control effect for higher modes is variable. It is also shown that, for a specific container geometry, a certain mass ratio leads to more efficient momentum transfer from the primary system to the particles with a better vibration attenuation effect, and that buffered particle dampers have better control effect than the conventional rigid ones. An analytical solution based on the discrete element method is also presented. Comparison between the experimental and computational results shows that reasonably accurate estimates of the response of a primary system can be obtained. Properly designed buffered particle dampers can effectively reduce the response of lightly damped mdof primary system with a small weight penalty, under different dynamic loads.

Quantifying and Qualifying USGS ShakeMap Uncertainty

USGS Publications Warehouse

Wald, David J.; Lin, Kuo-Wan; Quitoriano, Vincent

2008-01-01

We describe algorithms for quantifying and qualifying uncertainties associated with USGS ShakeMap ground motions. The uncertainty values computed consist of latitude/longitude grid-based multiplicative factors that scale the standard deviation associated with the ground motion prediction equation (GMPE) used within the ShakeMap algorithm for estimating ground motions. The resulting grid-based 'uncertainty map' is essential for evaluation of losses derived using ShakeMaps as the hazard input. For ShakeMap, ground motion uncertainty at any point is dominated by two main factors: (i) the influence of any proximal ground motion observations, and (ii) the uncertainty of estimating ground motions from the GMPE, most notably, elevated uncertainty due to initial, unconstrained source rupture geometry. The uncertainty is highest for larger magnitude earthquakes when source finiteness is not yet constrained and, hence, the distance to rupture is also uncertain. In addition to a spatially-dependant, quantitative assessment, many users may prefer a simple, qualitative grading for the entire ShakeMap. We developed a grading scale that allows one to quickly gauge the appropriate level of confidence when using rapidly produced ShakeMaps as part of the post-earthquake decision-making process or for qualitative assessments of archived or historical earthquake ShakeMaps. We describe an uncertainty letter grading ('A' through 'F', for high to poor quality, respectively) based on the uncertainty map. A middle-range ('C') grade corresponds to a ShakeMap for a moderate-magnitude earthquake suitably represented with a point-source location. Lower grades 'D' and 'F' are assigned for larger events (M>6) where finite-source dimensions are not yet constrained. The addition of ground motion observations (or observed macroseismic intensities) reduces uncertainties over data-constrained portions of the map. Higher grades ('A' and 'B') correspond to ShakeMaps with constrained fault dimensions and numerous stations, depending on the density of station/data coverage. Due to these dependencies, the letter grade can change with subsequent ShakeMap revisions if more data are added or when finite-faulting dimensions are added. We emphasize that the greatest uncertainties are associated with unconstrained source dimensions for large earthquakes where the distance term in the GMPE is most uncertain; this uncertainty thus scales with magnitude (and consequently rupture dimension). Since this distance uncertainty produces potentially large uncertainties in ShakeMap ground-motion estimates, this factor dominates over compensating constraints for all but the most dense station distributions.

An Atlas of ShakeMaps and population exposure catalog for earthquake loss modeling

USGS Publications Warehouse

Allen, T.I.; Wald, D.J.; Earle, P.S.; Marano, K.D.; Hotovec, A.J.; Lin, K.; Hearne, M.G.

2009-01-01

We present an Atlas of ShakeMaps and a catalog of human population exposures to moderate-to-strong ground shaking (EXPO-CAT) for recent historical earthquakes (1973-2007). The common purpose of the Atlas and exposure catalog is to calibrate earthquake loss models to be used in the US Geological Survey's Prompt Assessment of Global Earthquakes for Response (PAGER). The full ShakeMap Atlas currently comprises over 5,600 earthquakes from January 1973 through December 2007, with almost 500 of these maps constrained-to varying degrees-by instrumental ground motions, macroseismic intensity data, community internet intensity observations, and published earthquake rupture models. The catalog of human exposures is derived using current PAGER methodologies. Exposure to discrete levels of shaking intensity is obtained by correlating Atlas ShakeMaps with a global population database. Combining this population exposure dataset with historical earthquake loss data, such as PAGER-CAT, provides a useful resource for calibrating loss methodologies against a systematically-derived set of ShakeMap hazard outputs. We illustrate two example uses for EXPO-CAT; (1) simple objective ranking of country vulnerability to earthquakes, and; (2) the influence of time-of-day on earthquake mortality. In general, we observe that countries in similar geographic regions with similar construction practices tend to cluster spatially in terms of relative vulnerability. We also find little quantitative evidence to suggest that time-of-day is a significant factor in earthquake mortality. Moreover, earthquake mortality appears to be more systematically linked to the population exposed to severe ground shaking (Modified Mercalli Intensity VIII+). Finally, equipped with the full Atlas of ShakeMaps, we merge each of these maps and find the maximum estimated peak ground acceleration at any grid point in the world for the past 35 years. We subsequently compare this "composite ShakeMap" with existing global hazard models, calculating the spatial area of the existing hazard maps exceeded by the combined ShakeMap ground motions. In general, these analyses suggest that existing global, and regional, hazard maps tend to overestimate hazard. Both the Atlas of ShakeMaps and EXPO-CAT have many potential uses for examining earthquake risk and epidemiology. All of the datasets discussed herein are available for download on the PAGER Web page ( http://earthquake.usgs.gov/ eqcenter/pager/prodandref/ ). ?? 2009 Springer Science+Business Media B.V.

Urban Earthquake Shaking and Loss Assessment

NASA Astrophysics Data System (ADS)

Hancilar, U.; Tuzun, C.; Yenidogan, C.; Zulfikar, C.; Durukal, E.; Erdik, M.

2009-04-01

This study, conducted under the JRA-3 component of the EU NERIES Project, develops a methodology and software (ELER) for the rapid estimation of earthquake shaking and losses the Euro-Mediterranean region. This multi-level methodology developed together with researchers from Imperial College, NORSAR and ETH-Zurich is capable of incorporating regional variability and sources of uncertainty stemming from ground motion predictions, fault finiteness, site modifications, inventory of physical and social elements subjected to earthquake hazard and the associated vulnerability relationships. GRM Risk Management, Inc. of Istanbul serves as sub-contractor tor the coding of the ELER software. The methodology encompasses the following general steps: 1. Finding of the most likely location of the source of the earthquake using regional seismotectonic data base and basic source parameters, and if and when possible, by the estimation of fault rupture parameters from rapid inversion of data from on-line stations. 2. Estimation of the spatial distribution of selected ground motion parameters through region specific ground motion attenuation relationships and using shear wave velocity distributions.(Shake Mapping) 4. Incorporation of strong ground motion and other empirical macroseismic data for the improvement of Shake Map 5. Estimation of the losses (damage, casualty and economic) at different levels of sophistication (0, 1 and 2) that commensurate with the availability of inventory of human built environment (Loss Mapping) Level 2 analysis of the ELER Software (similar to HAZUS and SELENA) is essentially intended for earthquake risk assessment (building damage, consequential human casualties and macro economic loss quantifiers) in urban areas. The basic Shake Mapping is similar to the Level 0 and Level 1 analysis however, options are available for more sophisticated treatment of site response through externally entered data and improvement of the shake map through incorporation of accelerometric and other macroseismic data (similar to the USGS ShakeMap System). The building inventory data for the Level 2 analysis will consist of grid (geo-cell) based urban building and demographic inventories. For building grouping the European building typology developed within the EU-FP5 RISK-EU project is used. The building vulnerability/fragility relationships to be used can be user selected from a list of applicable relationships developed on the basis of a comprehensive study, Both empirical and analytical relationships (based on the Coefficient Method, Equivalent Linearization Method and the Reduction Factor Method of analysis) can be employed. Casualties in Level 2 analysis are estimated based on the number of buildings in different damaged states and the casualty rates for each building type and damage level. Modifications to the casualty rates can be used if necessary. ELER Level 2 analysis will include calculation of direct monetary losses as a result building damage that will allow for repair-cost estimations and specific investigations associated with earthquake insurance applications (PML and AAL estimations). ELER Level 2 analysis loss results obtained for Istanbul for a scenario earthquake using different techniques will be presented with comparisons using different earthquake damage assessment software. The urban earthquake shaking and loss information is intented for dissemination in a timely manner to related agencies for the planning and coordination of the post-earthquake emergency response. However the same software can also be used for scenario earthquake loss estimation, related Monte-Carlo type simulations and eathquake insurance applications.

Project Ranch Hand II. An Epidemiologic Investigation of Health Effects in Air Force Personnel Following Exposure to Herbicides. Mortality Update 1984.

DTIC Science & Technology

1984-12-10

population since the last report. Table 3 in this report corresponds to Table 3 in the baseline report and contains summary counts and death rates by...officers appears to compare favorably with the comparisons. However, these diminished death rates appear to be found in the Ranch Hand officers born before...experienced the same or greater death rate than their comparisons. !4 - .o 11 Table 14 Death Rates by Group, Rank, Occupation and Year-Of-Birth Ranch Hand

Combination of High Rate, Real-Time GNSS and Accelerometer Observations and Rapid Seismic Event Notification for Earthquake Early Warning and Volcano Monitoring with a Focus on the Pacific Rim.

NASA Astrophysics Data System (ADS)

Zimakov, L. G.; Passmore, P.; Raczka, J.; Alvarez, M.; Jackson, M.

2014-12-01

Scientific GNSS networks are moving towards a model of real-time data acquisition, epoch-by-epoch storage integrity, and on-board real-time position and displacement calculations. This new paradigm allows the integration of real-time, high-rate GNSS displacement information with acceleration and velocity data to create very high-rate displacement records. The mating of these two instruments allows the creation of a new, very high-rate (200 sps) displacement observable that has the full-scale displacement characteristics of GNSS and high-precision dynamic motions of seismic technologies. It is envisioned that these new observables can be used for earthquake early warning studies, volcano monitoring, and critical infrastructure monitoring applications. Our presentation will focus on the characteristics of GNSS, seismic, and strong motion sensors in high dynamic environments, including historic earthquakes in Southern California and the Pacific Rim, replicated on a shake table, over a range of displacements and frequencies. We will explore the optimum integration of these sensors from a filtering perspective including simple harmonic impulses over varying frequencies and amplitudes and under the dynamic conditions of various earthquake scenarios. In addition we will discuss implementation of a Rapid Seismic Event Notification System that provides quick delivery of digital data from seismic stations to the acquisition and processing center and a full data integrity model for real-time earthquake notification that provides warning prior to significant ground shaking.

Earthquake Shaking - Finding the "Hot Spots"

USGS Publications Warehouse

Field, Edward; Jones, Lucile; Jordan, Tom; Benthien, Mark; Wald, Lisa

2001-01-01

A new Southern California Earthquake Center study has quantified how local geologic conditions affect the shaking experienced in an earthquake. The important geologic factors at a site are softness of the rock or soil near the surface and thickness of the sediments above hard bedrock. Even when these 'site effects' are taken into account, however, each earthquake exhibits unique 'hotspots' of anomalously strong shaking. Better predictions of strong ground shaking will therefore require additional geologic data and more comprehensive computer simulations of individual earthquakes.

Building a Communication, Education, an Outreach Program for the ShakeAlert National Earthquake Early Warning Program - Recommendations for Public Alerts Via Cell Phones

NASA Astrophysics Data System (ADS)

DeGroot, R. M.; Long, K.; Strauss, J. A.

2017-12-01

The United States Geological Survey (USGS) and its partners are developing the ShakeAlert Earthquake Early Warning System for the West Coast of the United States. To be an integral part of successful implementation, ShakeAlert engagement programs and materials must integrate with and leverage broader earthquake risk programs. New methods and products for dissemination must be multidisciplinary, cost effective, and consistent with existing hazards education and communication efforts. The ShakeAlert Joint Committee for Communication, Education, and Outreach (JCCEO), is identifying, developing, and cultivating partnerships with ShakeAlert stakeholders including Federal, State, academic partners, private companies, policy makers, and local organizations. Efforts include developing materials, methods for delivery, and reaching stakeholders with information on ShakeAlert, earthquake preparedness, and emergency protective actions. It is essential to develop standards to ensure information communicated via the alerts is consistent across the public and private sector and achieving a common understanding of what actions users take when they receive a ShakeAlert warning. In February 2017, the JCCEO convened the Warning Message Focus Group (WMFG) to provide findings and recommendations to the Alliance for Telecommunications Industry Solutions on the use of earthquake early warning message content standards for public alerts via cell phones. The WMFG represents communications, education, and outreach stakeholders from various sectors including ShakeAlert regional coordinators, industry, emergency managers, and subject matter experts from the social sciences. The group knowledge was combined with an in-depth literature review to ensure that all groups who could receive the message would be taken into account. The USGS and the participating states and agencies acknowledge that the implementation of ShakeAlert is a collective effort requiring the participation of hundreds of stakeholders committed to ensuring public accessibility.

An Orientation Sensor-Based Head Tracking System for Driver Behaviour Monitoring

PubMed Central

Görne, Lorenz; Yuen, Iek-Man; Cao, Dongpu; Sullman, Mark; Auger, Daniel; Lv, Chen; Wang, Huaji; Matthias, Rebecca; Skrypchuk, Lee; Mouzakitis, Alexandros

2017-01-01

Although at present legislation does not allow drivers in a Level 3 autonomous vehicle to engage in a secondary task, there may become a time when it does. Monitoring the behaviour of drivers engaging in various non-driving activities (NDAs) is crucial to decide how well the driver will be able to take over control of the vehicle. One limitation of the commonly used face-based head tracking system, using cameras, is that sufficient features of the face must be visible, which limits the detectable angle of head movement and thereby measurable NDAs, unless multiple cameras are used. This paper proposes a novel orientation sensor based head tracking system that includes twin devices, one of which measures the movement of the vehicle while the other measures the absolute movement of the head. Measurement error in the shaking and nodding axes were less than 0.4°, while error in the rolling axis was less than 2°. Comparison with a camera-based system, through in-house tests and on-road tests, showed that the main advantage of the proposed system is the ability to detect angles larger than 20° in the shaking and nodding axes. Finally, a case study demonstrated that the measurement of the shaking and nodding angles, produced from the proposed system, can effectively characterise the drivers’ behaviour while engaged in the NDAs of chatting to a passenger and playing on a smartphone. PMID:29165331

Rapid and simple immunochemical screening combined with hand-shaking extraction for thiamethoxam residue in agricultural products.

PubMed

Watanabe, Eiki; Kobara, Yuso; Miyake, Shiro

2013-06-01

With the aim of expanding the applicability of a kit-based enzyme-linked immunosorbent assay (ELISA) for the neonicotinoid insecticide thiamethoxam, the ELISA was newly applied to three kinds of agricultural samples (green pepper, eggplant and spinach). To offer the ELISA as a screening analysis for thiamethoxam residues, a rapid and simple method of extraction by hand-shaking was used, and speed-up and simplification of the sample treatment before the ELISA analysis were examined. Finally, the validity of the ELISA combined with the proposed extraction method was verified against a reference high-performance liquid chromatography (HPLC) method using real-world agricultural samples. There were no marked matrix effects derived from green pepper and eggplant extracts. On the other hand, although the effect due to a pigment in spinach extract on the assay performance was significant, it was effectively avoided by increasing the dilution level of the spinach extract. For thiamethoxam-spiked samples, acceptable recoveries of 97.9-109.1% and coefficients of variation of 0.3-11.5% were obtained. Inspection of the validity of the ELISA by comparison with the reference HPLC method showed that the two analytical results were very similar, and a high correlation was found between them (r>0.997). The evaluated ELISA combined with hand-shaking extraction provided a rapid and simple screening analysis that was quantitative and reliable for the detection of thiamethoxam in complex agricultural products. © 2012 Society of Chemical Industry.

[A Case of Middle Cerebral Artery Stenosis Presented with Limb-Shaking TIA].

PubMed

Uno, Junji; Mineta, Haruyuki; Ren, Nice; Takagishi, Sou; Nagaoka, Shintarou; Kameda, Katsuharu; Maeda, Kazushi; Ikai, Yoshiaki; Gi, Hidefuku

2016-07-01

Involuntary movement is a rare clinical manifestation of transient ischemic attack (TIA). However, limb-shaking TIA is well described presentation of carotid occlusive disease. We present the case of a patient who developed limb-shaking TIA associated with high-grade stenosis of middle cerebral artery (M1), which was treated with percutaneous transluminal angioplasty (PTA). The procedure was performed successfully without complication and the symptom disappeared immediately after the procedure. The patient remained free of symptoms at the 38-month follow-up. There was no tendency of restenosis of M1. In this case, PTA was technically feasible and beneficial for limb-shaking TIA with M1 stenosis. Limb-shaking TIA can be a symptom of high-grade stenosis of M1.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hurricane, O. A.; Thomas, C.; Olson, R.

Recent data on implosions using identical hohlraums and very similar laser drives underscores the conundrum of making a clear choice of one ablator over another. Table I shows a comparison of Be and CH in a nominal length, gold, 575 μm-diameter, 1.6 mg/cc He gas-fill hohlraum while Table II shows a comparison of undoped HDC and CH in a +700 length, gold, 575 μm diameter, 1.6 mg/cc He gas fill hohlraum. As can be seen in the tables, the net integrated fusion performance of these ablators is the same to within error bars. In the case of the undoped HDCmore » and CH ablators, the hot spot shapes of the implosions were nearly indistinguishable for the experiments listed in Table II.« less

FIRST NEW SOLAR MODELS WITH OPAS OPACITY TABLES

DOE Office of Scientific and Technical Information (OSTI.GOV)

Le Pennec, M.; Turck-Chièze, S.; Salmon, S.

Stellar seismology appears more and more as a powerful tool for a better determination of the fundamental properties of solar-type stars. However, the particular case of the Sun is still challenging. For about a decade now, the helioseismic sound-speed determination has continued to disagree with the standard solar model (SSM) prediction, questioning the reliability of this model. One of the sources of uncertainty could be in the treatment of the transport of radiation from the solar core to the surface. In this Letter, we use the new OPAS opacity tables, recently available for solar modeling, to address this issue. Wemore » discuss first the peculiarities of these tables, then we quantify their impact on the solar sound-speed and density profiles using the reduced OPAS tables taken on the grids of the OPAL ones. We use the two evolution codes, Modules for Experiments in Stellar Astrophysics and Code Liégeois d’Evolution Stellaire, that led to similar conclusions in the solar radiative zone. In comparison to commonly used OPAL opacity tables, the new solar models are computed for the most recent photospheric composition with OPAS tables and present improvements to the location of the base of the convective zone and to the description of the solar radiative zone in comparison to the helioseismic observations, even if the differences in the Rosseland mean opacity do not exceed 6%. We finally carry out a comparison to a solar model computed with the OP opacity tables.« less

Behavioral Response in the Immediate Aftermath of Shaking: Earthquakes in Christchurch and Wellington, New Zealand, and Hitachi, Japan

PubMed Central

Jon, Ihnji; Lindell, Michael K.; Prater, Carla S.; Huang, Shih-Kai; Wu, Hao-Che; Johnston, David M.; Becker, Julia S.; Shiroshita, Hideyuki; Doyle, Emma E.H.; Potter, Sally H.; McClure, John; Lambie, Emily

2016-01-01

This study examines people’s response actions in the first 30 min after shaking stopped following earthquakes in Christchurch and Wellington, New Zealand, and Hitachi, Japan. Data collected from 257 respondents in Christchurch, 332 respondents in Hitachi, and 204 respondents in Wellington revealed notable similarities in some response actions immediately after the shaking stopped. In all four events, people were most likely to contact family members and seek additional information about the situation. However, there were notable differences among events in the frequency of resuming previous activities. Actions taken in the first 30 min were weakly related to: demographic variables, earthquake experience, contextual variables, and actions taken during the shaking, but were significantly related to perceived shaking intensity, risk perception and affective responses to the shaking, and damage/infrastructure disruption. These results have important implications for future research and practice because they identify promising avenues for emergency managers to communicate seismic risks and appropriate responses to risk area populations. PMID:27854306

Behavioral Response in the Immediate Aftermath of Shaking: Earthquakes in Christchurch and Wellington, New Zealand, and Hitachi, Japan.

PubMed

Jon, Ihnji; Lindell, Michael K; Prater, Carla S; Huang, Shih-Kai; Wu, Hao-Che; Johnston, David M; Becker, Julia S; Shiroshita, Hideyuki; Doyle, Emma E H; Potter, Sally H; McClure, John; Lambie, Emily

2016-11-15

This study examines people's response actions in the first 30 min after shaking stopped following earthquakes in Christchurch and Wellington, New Zealand, and Hitachi, Japan. Data collected from 257 respondents in Christchurch, 332 respondents in Hitachi, and 204 respondents in Wellington revealed notable similarities in some response actions immediately after the shaking stopped. In all four events, people were most likely to contact family members and seek additional information about the situation. However, there were notable differences among events in the frequency of resuming previous activities. Actions taken in the first 30 min were weakly related to: demographic variables, earthquake experience, contextual variables, and actions taken during the shaking, but were significantly related to perceived shaking intensity, risk perception and affective responses to the shaking, and damage/infrastructure disruption. These results have important implications for future research and practice because they identify promising avenues for emergency managers to communicate seismic risks and appropriate responses to risk area populations.

Regional Earthquake Shaking and Loss Estimation

NASA Astrophysics Data System (ADS)

Sesetyan, K.; Demircioglu, M. B.; Zulfikar, C.; Durukal, E.; Erdik, M.

2009-04-01

This study, conducted under the JRA-3 component of the EU NERIES Project, develops a methodology and software (ELER) for the rapid estimation of earthquake shaking and losses in the Euro-Mediterranean region. This multi-level methodology developed together with researchers from Imperial College, NORSAR and ETH-Zurich is capable of incorporating regional variability and sources of uncertainty stemming from ground motion predictions, fault finiteness, site modifications, inventory of physical and social elements subjected to earthquake hazard and the associated vulnerability relationships. GRM Risk Management, Inc. of Istanbul serves as sub-contractor tor the coding of the ELER software. The methodology encompasses the following general steps: 1. Finding of the most likely location of the source of the earthquake using regional seismotectonic data base and basic source parameters, and if and when possible, by the estimation of fault rupture parameters from rapid inversion of data from on-line stations. 2. Estimation of the spatial distribution of selected ground motion parameters through region specific ground motion attenuation relationships and using shear wave velocity distributions.(Shake Mapping) 4. Incorporation of strong ground motion and other empirical macroseismic data for the improvement of Shake Map 5. Estimation of the losses (damage, casualty and economic) at different levels of sophistication (0, 1 and 2) that commensurate with the availability of inventory of human built environment (Loss Mapping) Both Level 0 (similar to PAGER system of USGS) and Level 1 analyses of the ELER routine are based on obtaining intensity distributions analytically and estimating total number of casualties and their geographic distribution either using regionally adjusted intensity-casualty or magnitude-casualty correlations (Level 0) of using regional building inventory data bases (Level 1). Level 0 analysis is similar to the PAGER system being developed by USGS. For given basis source parameters the intensity distributions can be computed using: a)Regional intensity attenuation relationships, b)Intensity correlations with attenuation relationship based PGV, PGA, and Spectral Amplitudes and, c)Intensity correlations with synthetic Fourier Amplitude Spectrum. In Level 1 analysis EMS98 based building vulnerability relationships are used for regional estimates of building damage and the casualty distributions. Results obtained from pilot applications of the Level 0 and Level 1 analysis modes of the ELER software to the 1999 M 7.4 Kocaeli, 1995 M 6.1 Dinar, and 2007 M 5.4 Bingol earthquakes in terms of ground shaking and losses are presented and comparisons with the observed losses are made. The regional earthquake shaking and loss information is intented for dissemination in a timely manner to related agencies for the planning and coordination of the post-earthquake emergency response. However the same software can also be used for scenario earthquake loss estimation and related Monte-Carlo type simulations.

Medium-high frequency FBG accelerometer with integrative matrix structure.

PubMed

Dai, Yutang; Yin, Guanglin; Liu, Bin; Xu, Gang; Karanja, Joseph Muna

2015-04-10

To meet the requirements for medium-high frequency vibration monitoring, a new type fiber Bragg grating (FBG) accelerometer with an integrative matrix structure is proposed. Two symmetrical flexible gemels are used as elastic elements, which drive respective inertial mass moving reversely when exciting vibration exists, leading to doubling the wavelength shift of the FBG. The mechanics model and a numerical method are presented in this paper, by which the influence of the structural parameters on the sensitivity and eigenfrequency is discussed. Sensitivity higher than 200  pm/g and an eigenfrequency larger than 3000 Hz can be realized separately, but both cannot be achieved simultaneously. Aiming for a broader measuring frequency range, a prototype accelerometer with an eigenfrequency near 3000 Hz is designed, and results from a shake table test are also demonstrated.

Response of a 2-story test-bed structure for the seismic evaluation of nonstructural systems

NASA Astrophysics Data System (ADS)

Soroushian, Siavash; Maragakis, E. "Manos"; Zaghi, Arash E.; Rahmanishamsi, Esmaeel; Itani, Ahmad M.; Pekcan, Gokhan

2016-03-01

A full-scale, two-story, two-by-one bay, steel braced-frame was subjected to a number of unidirectional ground motions using three shake tables at the UNR-NEES site. The test-bed frame was designed to study the seismic performance of nonstructural systems including steel-framed gypsum partition walls, suspended ceilings and fire sprinkler systems. The frame can be configured to perform as an elastic or inelastic system to generate large floor accelerations or large inter story drift, respectively. In this study, the dynamic performance of the linear and nonlinear test-beds was comprehensively studied. The seismic performance of nonstructural systems installed in the linear and nonlinear test-beds were assessed during extreme excitations. In addition, the dynamic interactions of the test-bed and installed nonstructural systems are investigated.

Metadata and network API aspects of a framework for storing and retrieving civil infrastructure monitoring data

NASA Astrophysics Data System (ADS)

Wong, John-Michael; Stojadinovic, Bozidar

2005-05-01

A framework has been defined for storing and retrieving civil infrastructure monitoring data over a network. The framework consists of two primary components: metadata and network communications. The metadata component provides the descriptions and data definitions necessary for cataloging and searching monitoring data. The communications component provides Java classes for remotely accessing the data. Packages of Enterprise JavaBeans and data handling utility classes are written to use the underlying metadata information to build real-time monitoring applications. The utility of the framework was evaluated using wireless accelerometers on a shaking table earthquake simulation test of a reinforced concrete bridge column. The NEESgrid data and metadata repository services were used as a backend storage implementation. A web interface was created to demonstrate the utility of the data model and provides an example health monitoring application.

Evaluation of dispersion methods for enumeration of microorganisms from peat and activated carbon biofilters treating volatile organic compounds.

PubMed

Khammar, Nadia; Malhautier, Luc; Degrange, Valérie; Lensi, Robert; Fanlo, Jean-Louis

2004-01-01

To enumerate microorganisms having colonized biofilters treating volatile organic compounds, it is necessary firstly to evaluate dispersion methods. Crushing, shaking and sonication were then tested for the removal of microflora from biofilters packing materials (peat and activated carbon). Continuous or discontinuous procedures, and addition of glass beads had no effect on the number of microorganisms removed from peat particles. The duration of treatment also had no effect for shaking and crushing, but the number of microorganisms after 60 min of treatment with ultrasound was significantly higher than that obtained after 0.5 min. The comparison between these methods showed that crushing was the most efficient for the removal of microorganisms from both peat and activated carbon. The comparison between three chemical dispersion agents showed that 1% Na-pyrophosphate was less efficient, compared with 200 mM phosphate buffer or 1% Na-hexametaphosphate. To optimize the cultivation of microorganisms, three different agar media were compared. Tryptic soy agar tenfold diluted (TSA 1/10) was the most suitable medium for the culture of microflora from a peat biofilter. For the activated carbon biofilter, there was no significant difference between Luria Bertoni, TSA 1/10, and plate count agar. The optimized extraction and enumeration protocols were used to perform a quantitative characterization of microbial populations in an operating laboratory activated carbon biofilter and in two parallel peat biofilters.

MyEEW: A Smartphone App for the ShakeAlert System

NASA Astrophysics Data System (ADS)

Strauss, J. A.; Allen, S.; Allen, R. M.; Hellweg, M.

2015-12-01

Earthquake Early Warning (EEW) is a system that can provide a few to tens of seconds warning prior to ground shaking at a user's location. The goal and purpose of such a system is to reduce, or minimize, the damage, costs, and casualties resulting from an earthquake. A demonstration earthquake early warning system (ShakeAlert) is undergoing testing in the United States by the UC Berkeley Seismological Laboratory, Caltech, ETH Zurich, University of Washington, the USGS, and beta users in California and the Pacific Northwest. The UC Berkeley Seismological Laboratory has created a smartphone app called MyEEW, which interfaces with the ShakeAlert system to deliver early warnings to individual users. Many critical facilities (transportation, police, and fire) have control rooms, which could run a centralized interface, but our ShakeAlert Beta Testers have also expressed their need for mobile options. This app augments the basic ShakeAlert Java desktop applet by allowing workers off-site (or merely out of hearing range) to be informed of coming hazards. MyEEW receives information from the ShakeAlert system to provide users with real-time information about shaking that is about to happen at their individual location. It includes a map, timer, and earthquake information similar to the Java desktop User Display. The app will also feature educational material to help users craft their own response and resiliency strategies. The app will be open to UC Berkeley Earthquake Research Affiliates members for testing in the near future.

Demonstrating the Environmental & Economic Cost-Benefits of Reusing DoD’s Pre-World War II Buildings

DTIC Science & Technology

2013-04-01

IV-1 Table IV-2: Summary Results PO1, NPV of Life Cycle Costs wirhout Factoring GHGs ......... IV...3 Table IV-3: Summary Results PO1, NPV of Life Cycle Costs with Monetized GHGs ............. IV-4 Table IV-4: Construction Cost Comparisons...IV-6 Table IV-6: Summary Results PO2, GHG Reductions in Metric Tons by Scope

Installation, care, and maintenance of wood shake and shingle siding

Treesearch

Jack Dwyer; Tony Bonura; Arnie Nebelsick; Sam Williams; Christopher G. Hunt

2011-01-01

This article gives general guidelines for selection, installation, finishing, and maintenance of wood shakes and shingles. The authors gathered information from a variety of sources: research publications on wood finishing, technical data sheets from paint manufacturers, installation instructions for shake and shingle siding, and interviews with experts having...

Test and evaluation of the attic temperature reduction potential of plastic roof shakes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Holton, J.K.; Beggs, T.R.

1999-07-01

While monitoring the comparative performance of two test houses in Pittsburgh, Pennsylvania, it was noticed that the attic air temperature of one house with a plastic shake roof was consistently 20 F (11 C) cooler than its twin with asphalt shingles during peak summer cooling periods. More detailed monitoring of the temperatures on the plastic shake, the roof deck, and the attic showed this effect to be largely due to the plastic shake and not to better roof venting or other heat loss mechanisms.

Oxygen transfer phenomena in 48-well microtiter plates: determination by optical monitoring of sulfite oxidation and verification by real-time measurement during microbial growth.

PubMed

Kensy, Frank; Zimmermann, Hartmut F; Knabben, Ingo; Anderlei, Tibor; Trauthwein, Harald; Dingerdissen, Uwe; Büchs, Jochen

2005-03-20

Oxygen limitation is one of the most frequent problems associated with the application of shaking bioreactors. The gas-liquid oxygen transfer properties of shaken 48-well microtiter plates (MTPs) were analyzed at different filling volumes, shaking diameters, and shaking frequencies. On the one hand, an optical method based on sulfite oxidation was used as a chemical model system to determine the maximum oxygen transfer capacity (OTR(max)). On the other hand, the Respiration Activity Monitoring System (RAMOS) was applied for online measurement of the oxygen transfer rate (OTR) during growth of the methylotropic yeast Hansenula polymorpha. A proportionality constant between the OTR(max) of the biological system and the OTR(max) of the chemical system were indicated from these data, offering the possibility to transform the whole set of chemical data to biologically relevant conditions. The results exposed "out of phase" shaking conditions at a shaking diameter of 1 mm, which were confirmed by theoretical consideration with the phase number (Ph). At larger shaking diameters (2-50 mm) the oxygen transfer rate in MTPs shaken at high frequencies reached values of up to 0.28 mol/L/h, corresponding to a volumetric mass transfer coefficient (k(L)a) of 1,600 1/h. The specific mass transfer area (a) increases exponentially with the shaking frequency up to values of 2,400 1/m. On the contrary, the mass transfer coefficient (k(L)) is constant at a level of about 0.15 m/h over a wide range of shaking frequencies and shaking diameters. However, at high shaking frequencies, when the complete liquid volume forms a thin film on the cylindric wall of the well, the mass transfer coefficient (k(L)) increases linearly to values of up to 0.76 m/h. Essentially, the present investigation demonstrates that the 48-well plate outperforms the 96-well MTP and shake flasks at widely used operating conditions with respect to oxygen supply. The 48-well plates emerge, therefore, as an excellent alternative for microbial cultivation and expression studies combining the advantages of both the high-throughput 96-well MTP and the classical shaken Erlenmeyer flask.

Introducing ShakeMap to potential users in Puerto Rico using scenarios of damaging historical and probable earthquakes

NASA Astrophysics Data System (ADS)

Huerfano, V. A.; Cua, G.; von Hillebrandt, C.; Saffar, A.

2007-12-01

The island of Puerto Rico has a long history of damaging earthquakes. Major earthquakes from off-shore sources have affected Puerto Rico in 1520, 1615, 1670, 1751, 1787, 1867, and 1918 (Mueller et al, 2003; PRSN Catalogue). Recent trenching has also yielded evidence of possible M7.0 events inland (Prentice, 2000). The high seismic hazard, large population, high tsunami potential and relatively poor construction practice can result in a potentially devastating combination. Efficient emergency response in event of a large earthquake will be crucial to minimizing the loss of life and disruption of lifeline systems in Puerto Rico. The ShakeMap system (Wald et al, 2004) developed by the USGS to rapidly display and disseminate information about the geographical distribution of ground shaking (and hence potential damage) following a large earthquake has proven to be a vital tool for post earthquake emergency response efforts, and is being adopted/emulated in various seismically active regions worldwide. Implementing a robust ShakeMap system is among the top priorities of the Puerto Rico Seismic Network. However, the ultimate effectiveness of ShakeMap in post- earthquake response depends not only on its rapid availability, but also on the effective use of the information it provides. We developed ShakeMap scenarios of a suite of damaging historical and probable earthquakes that severely impact San Juan, Ponce, and Mayagüez, the 3 largest cities in Puerto Rico. Earthquake source parameters were obtained from McCann and Mercado (1998); and Huérfano (2004). For historical earthquakes that generated tsunamis, tsunami inundation maps were generated using the TIME method (Shuto, 1991). The ShakeMap ground shaking maps were presented to local and regional governmental and emergency response agencies at the 2007 Annual conference of the Puerto Rico Emergency Management and Disaster Administration in San Juan, PR, and at numerous other emergency management talks and training sessions. Economic losses are estimated using the ShakeMap scenario ground motions (Saffar, 2007). The calibration tasks necessary in generating these scenarios (developing Vs30 maps, attenuation relationships) complement the on-going efforts of the Puerto Rico Seismic Network to generate ShakeMaps in real-time.

Installation, care, and maintenance of wood shake and shingle roofs

Treesearch

Tony Bonura; Jack Dwyer; Arnie Nebelsick; Brent Stuart; R. Sam Williams; Christopher Hunt

2011-01-01

This article gives general guidelines for selection, installation, finishing, and maintenance of wood shake and shingle roofs. The authors have gathered information from a variety of sources: research publications on wood finishing, technical data sheets from paint manufacturers, installation instructions for shake and shingle roofs, and interviews with experts having...

Raspberry Shake- A World-Wide Citizen Seismograph Network

NASA Astrophysics Data System (ADS)

Christensen, B. C.; Blanco Chia, J. F.

2017-12-01

Raspberry Shake was conceived as an inexpensive plug-and-play solution to satisfy the need for universal, quick and accurate earthquake detections. First launched on Kickstarter's crowdfunding platform in July of 2016, the Raspberry Shake project was funded within hours of the launch date and, by the end of the campaign, reached more than 1000% of its initial funding goal. This demonstrated for the first time that there exists a strong interest among Makers, Hobbyists and Do It Yourselfers for personal seismographs. From here, a citizen scientist network was created and it has steadily been growing. The Raspberry Shake network is currently being used in conjunction with publicly available broadband data from the GSN and other state-run seismic networks available through the IRIS, Geoscope and GEOFON data centers to detect and locate earthquakes large and small around the globe. Raspberry Shake looks well positioned to improve local monitoring of earthquakes on a global scale, deepen community's understanding of earthquakes, and serve as a formidable teaching tool. We present the main results of the project, the current state of the network, and the new Raspberry Shake models that are being built.

ShakeMap Atlas 2.0: an improved suite of recent historical earthquake ShakeMaps for global hazard analyses and loss model calibration

USGS Publications Warehouse

Garcia, D.; Mah, R.T.; Johnson, K.L.; Hearne, M.G.; Marano, K.D.; Lin, K.-W.; Wald, D.J.

2012-01-01

We introduce the second version of the U.S. Geological Survey ShakeMap Atlas, which is an openly-available compilation of nearly 8,000 ShakeMaps of the most significant global earthquakes between 1973 and 2011. This revision of the Atlas includes: (1) a new version of the ShakeMap software that improves data usage and uncertainty estimations; (2) an updated earthquake source catalogue that includes regional locations and finite fault models; (3) a refined strategy to select prediction and conversion equations based on a new seismotectonic regionalization scheme; and (4) vastly more macroseismic intensity and ground-motion data from regional agencies All these changes make the new Atlas a self-consistent, calibrated ShakeMap catalogue that constitutes an invaluable resource for investigating near-source strong ground-motion, as well as for seismic hazard, scenario, risk, and loss-model development. To this end, the Atlas will provide a hazard base layer for PAGER loss calibration and for the Earthquake Consequences Database within the Global Earthquake Model initiative.

Water-table and discharge changes associated with the 2016-2017 seismic sequence in central Italy: hydrogeological data and a conceptual model for fractured carbonate aquifers

NASA Astrophysics Data System (ADS)

Petitta, Marco; Mastrorillo, Lucia; Preziosi, Elisabetta; Banzato, Francesca; Barberio, Marino Domenico; Billi, Andrea; Cambi, Costanza; De Luca, Gaetano; Di Carlo, Giuseppe; Di Curzio, Diego; Di Salvo, Cristina; Nanni, Torquato; Palpacelli, Stefano; Rusi, Sergio; Saroli, Michele; Tallini, Marco; Tazioli, Alberto; Valigi, Daniela; Vivalda, Paola; Doglioni, Carlo

2018-01-01

A seismic sequence in central Italy from August 2016 to January 2017 affected groundwater dynamics in fractured carbonate aquifers. Changes in spring discharge, water-table position, and streamflow were recorded for several months following nine Mw 5.0-6.5 seismic events. Data from 22 measurement sites, located within 100 km of the epicentral zones, were analyzed. The intensity of the induced changes were correlated with seismic magnitude and distance to epicenters. The additional post-seismic discharge from rivers and springs was found to be higher than 9 m3/s, totaling more than 0.1 km3 of groundwater release over 6 months. This huge and unexpected contribution increased streamflow in narrow mountainous valleys to previously unmeasured peak values. Analogously to the L'Aquila 2009 post-earthquake phenomenon, these hydrogeological changes might reflect an increase of bulk hydraulic conductivity at the aquifer scale, which would increase hydraulic heads in the discharge zones and lower them in some recharge areas. The observed changes may also be partly due to other mechanisms, such as shaking and/or squeezing effects related to intense subsidence in the core of the affected area, where effects had maximum extent, or breaching of hydraulic barriers.

Water-table and discharge changes associated with the 2016-2017 seismic sequence in central Italy: hydrogeological data and a conceptual model for fractured carbonate aquifers

NASA Astrophysics Data System (ADS)

Petitta, Marco; Mastrorillo, Lucia; Preziosi, Elisabetta; Banzato, Francesca; Barberio, Marino Domenico; Billi, Andrea; Cambi, Costanza; De Luca, Gaetano; Di Carlo, Giuseppe; Di Curzio, Diego; Di Salvo, Cristina; Nanni, Torquato; Palpacelli, Stefano; Rusi, Sergio; Saroli, Michele; Tallini, Marco; Tazioli, Alberto; Valigi, Daniela; Vivalda, Paola; Doglioni, Carlo

2018-06-01

A seismic sequence in central Italy from August 2016 to January 2017 affected groundwater dynamics in fractured carbonate aquifers. Changes in spring discharge, water-table position, and streamflow were recorded for several months following nine Mw 5.0-6.5 seismic events. Data from 22 measurement sites, located within 100 km of the epicentral zones, were analyzed. The intensity of the induced changes were correlated with seismic magnitude and distance to epicenters. The additional post-seismic discharge from rivers and springs was found to be higher than 9 m3/s, totaling more than 0.1 km3 of groundwater release over 6 months. This huge and unexpected contribution increased streamflow in narrow mountainous valleys to previously unmeasured peak values. Analogously to the L'Aquila 2009 post-earthquake phenomenon, these hydrogeological changes might reflect an increase of bulk hydraulic conductivity at the aquifer scale, which would increase hydraulic heads in the discharge zones and lower them in some recharge areas. The observed changes may also be partly due to other mechanisms, such as shaking and/or squeezing effects related to intense subsidence in the core of the affected area, where effects had maximum extent, or breaching of hydraulic barriers.

Interpreting plant responses to clinostating. I - Mechanical stresses and ethylene

NASA Technical Reports Server (NTRS)

Salisbury, Frank B.; Wheeler, Raymond M.

1981-01-01

The possibility that the clinostat mechanical stresses (leaf flopping) induces ethylene production and, thus, the development of epinasty was tested by stressing vertical plants by constant gentle horizontal or vertical shaking or by a quick back-and-forth rotation (twisting). Clinostat leaf flopping was closely approximated by turning plants so that their stems were horizontal, rotating them quickly about the stem axis, and returning them to the vertical, with the treatment repeated every four minutes. It was found that horizontal and vertical shaking, twisting, intermittent horizontal rotating, and gentle hand shaking failed to induce epinasties that approached those observed on the slow clinostat. Minor epinasties were generated by vigorous hand-shaking (120 sec/day) and by daily application of Ag(+). Reducing leaf displacements by inverting plants did not significantly reduce the minor epinasty generated by vigorous hand-shaking.

A comparison of northern and southern table mountain pine stands

Treesearch

Patrick H. Brose; Thomas A. Waldrop; Helen H. Mohr

2010-01-01

Table Mountain pine (Pinus pungens) stands occur throughout the Appalachian Mountains, but ecological research has concentrated on the southern part of this region. In 2006, research was initiated in northern Table Mountain pine stands growing in PA to compare some basic attributes of those stands with previously described ones in TN. Overall, the...

The ShakeOut earthquake scenario: Verification of three simulation sets

USGS Publications Warehouse

Bielak, J.; Graves, R.W.; Olsen, K.B.; Taborda, R.; Ramirez-Guzman, L.; Day, S.M.; Ely, G.P.; Roten, D.; Jordan, T.H.; Maechling, P.J.; Urbanic, J.; Cui, Y.; Juve, G.

2010-01-01

This paper presents a verification of three simulations of the ShakeOut scenario, an Mw 7.8 earthquake on a portion of the San Andreas fault in southern California, conducted by three different groups at the Southern California Earthquake Center using the SCEC Community Velocity Model for this region. We conducted two simulations using the finite difference method, and one by the finite element method, and performed qualitative and quantitative comparisons between the corresponding results. The results are in good agreement with each other; only small differences occur both in amplitude and phase between the various synthetics at ten observation points located near and away from the fault-as far as 150 km away from the fault. Using an available goodness-of-fit criterion all the comparisons scored above 8, with most above 9.2. This score would be regarded as excellent if the measurements were between recorded and synthetic seismograms. We also report results of comparisons based on time-frequency misfit criteria. Results from these two criteria can be used for calibrating the two methods for comparing seismograms. In those cases in which noticeable discrepancies occurred between the seismograms generated by the three groups, we found that they were the product of inherent characteristics of the various numerical methods used and their implementations. In particular, we found that the major source of discrepancy lies in the difference between mesh and grid representations of the same material model. Overall, however, even the largest differences in the synthetic seismograms are small. Thus, given the complexity of the simulations used in this verification, it appears that the three schemes are consistent, reliable and sufficiently accurate and robust for use in future large-scale simulations. ?? 2009 The Authors Journal compilation ?? 2009 RAS.

Characterization of the Physical Stability of a Lyophilized IgG1 mAb After Accelerated Shipping-like Stress

PubMed Central

Telikepalli, Srivalli; Kumru, Ozan S.; Kim, Jae Hyun; Joshi, Sangeeta B.; O'Berry, Kristin B.; Blake-Haskins, Angela W.; Perkins, Melissa D.; Middaugh, C. Russell; Volkin, David B.

2014-01-01

Upon exposure to shaking stress, an IgG1 mAb formulation in both liquid and lyophilized state formed subvisible particles. Since freeze-drying is expected to minimize protein physical instability under these conditions, the extent and nature of aggregate formation in the lyophilized preparation was examined using a variety of particle characterization techniques. The effect of formulation variables such as residual moisture content, reconstitution rate, and reconstitution medium were examined. Upon reconstitution of shake-stressed lyophilized mAb, differences in protein particle size and number were observed by Microflow Digital Imaging (MFI), with the reconstitution medium having the largest impact. Shake-stress had minor effects on the structure of protein within the particles as shown by SDS-PAGE and FTIR analysis. The lyophilized mAb was shake-stressed to different extents and stored for 3 months at different temperatures. Both extent of cake collapse and storage temperature affected the physical stability of the shake-stressed lyophilized mAb upon subsequent storage. These findings demonstrate that physical degradation upon shaking of a lyophilized IgG1 mAb formulation includes not only cake breakage, but also results in an increase in subvisible particles and turbidity upon reconstitution. The shaking-induced cake breakage of the lyophilized IgG1 mAb formulation also resulted in decreased physical stability upon storage. PMID:25522000

The Shaking Torch: Another Variation on the Inductive Force

ERIC Educational Resources Information Center

Thompson, Frank

2010-01-01

A recent article showed how the influx of neodymium magnets has provided striking demonstrations of the interactions between magnets and conductors. The "shaking torch" is yet another example. Many of these torches require no batteries and can be submerged in water--indeed, a light for life. In this article, the author disassembles a shaking torch…

Perpetrator Accounts in Infant Abusive Head Trauma Brought about by a Shaking Event

ERIC Educational Resources Information Center

Biron, Dean; Shelton, Doug

2005-01-01

Objective: To analyze perpetrator and medical evidence collected during investigations of infant abusive head trauma (IAHT), with a view to (a) identifying cases where injuries were induced by shaking in the absence of any impact and (b) documenting the response of infant victims to a violent shaking event. Method: A retrospective study was…

Multi-Agent Framework for the Fair Division of Resources and Tasks

DTIC Science & Technology

2006-01-01

144 B.1.2 Application of Shake Out Algorithm to JFK Airport Test Data.........................144 B.2 Generalization...145 Figure B–2: Available Aircraft Inventory at JFK Airport ............................................. 148 Figure B–3...Available Aircraft Inventory at JFK Airport after the first shake out ....... 148 Figure B–4: Inventory Vectors for Second and Third Shake Outs

An empirical model for global earthquake fatality estimation

USGS Publications Warehouse

Jaiswal, Kishor; Wald, David

2010-01-01

We analyzed mortality rates of earthquakes worldwide and developed a country/region-specific empirical model for earthquake fatality estimation within the U.S. Geological Survey's Prompt Assessment of Global Earthquakes for Response (PAGER) system. The earthquake fatality rate is defined as total killed divided by total population exposed at specific shaking intensity level. The total fatalities for a given earthquake are estimated by multiplying the number of people exposed at each shaking intensity level by the fatality rates for that level and then summing them at all relevant shaking intensities. The fatality rate is expressed in terms of a two-parameter lognormal cumulative distribution function of shaking intensity. The parameters are obtained for each country or a region by minimizing the residual error in hindcasting the total shaking-related deaths from earthquakes recorded between 1973 and 2007. A new global regionalization scheme is used to combine the fatality data across different countries with similar vulnerability traits.

Forest statistics for Southwest-South Alabama counties - 1990

Treesearch

William H. McWilliams; Patrick E. Miller; John S. Vissage

1990-01-01

Tabulated results were derived from data obtained during a recent forest inventory of southeast Alabama (fig. 1). Core tables (1 to 25) are compatible among Forest Inventory and Analysis units in the Eastern U.S. Other tables (26 to 43) supplement the information contained in the core tables. Comparisons are made between results of the 1990 inventory and previous...

A Comparison of Fire Intensity levels for stand replacement of table mountain pine (Pinus pungens Lamb.)

Treesearch

Thomas A. Waldrop; Patrick H. Brose

1999-01-01

Stand-replacement prescribed fire has been recommended to regenerate stands of table mountain pine (Pinus pungens Lamb.) in the Southern Appalachian Mountains because the species has serotinous cones and is shade intolerant. A 350 ha prescribed fire in northeast Georgia provided an opportunity to observe overstory mortality and regeneration of table...

Validation of a wireless modular monitoring system for structures

NASA Astrophysics Data System (ADS)

Lynch, Jerome P.; Law, Kincho H.; Kiremidjian, Anne S.; Carryer, John E.; Kenny, Thomas W.; Partridge, Aaron; Sundararajan, Arvind

2002-06-01

A wireless sensing unit for use in a Wireless Modular Monitoring System (WiMMS) has been designed and constructed. Drawing upon advanced technological developments in the areas of wireless communications, low-power microprocessors and micro-electro mechanical system (MEMS) sensing transducers, the wireless sensing unit represents a high-performance yet low-cost solution to monitoring the short-term and long-term performance of structures. A sophisticated reduced instruction set computer (RISC) microcontroller is placed at the core of the unit to accommodate on-board computations, measurement filtering and data interrogation algorithms. The functionality of the wireless sensing unit is validated through various experiments involving multiple sensing transducers interfaced to the sensing unit. In particular, MEMS-based accelerometers are used as the primary sensing transducer in this study's validation experiments. A five degree of freedom scaled test structure mounted upon a shaking table is employed for system validation.

Measuring relative-story displacement and local inclination angle using multiple position-sensitive detectors.

PubMed

Matsuya, Iwao; Katamura, Ryuta; Sato, Maya; Iba, Miroku; Kondo, Hideaki; Kanekawa, Kiyoshi; Takahashi, Motoichi; Hatada, Tomohiko; Nitta, Yoshihiro; Tanii, Takashi; Shoji, Shuichi; Nishitani, Akira; Ohdomari, Iwao

2010-01-01

We propose a novel sensor system for monitoring the structural health of a building. The system optically measures the relative-story displacement during earthquakes for detecting any deformations of building elements. The sensor unit is composed of three position sensitive detectors (PSDs) and lenses capable of measuring the relative-story displacement precisely, even if the PSD unit was inclined in response to the seismic vibration. For verification, laboratory tests were carried out using an Xθ-stage and a shaking table. The static experiment verified that the sensor could measure the local inclination angle as well as the lateral displacement. The dynamic experiment revealed that the accuracy of the sensor was 150 μm in the relative-displacement measurement and 100 μrad in the inclination angle measurement. These results indicate that the proposed sensor system has sufficient accuracy for the measurement of relative-story displacement in response to the seismic vibration.

Semi-active friction damper for buildings subject to seismic excitation

NASA Astrophysics Data System (ADS)

Mantilla, Juan S.; Solarte, Alexander; Gomez, Daniel; Marulanda, Johannio; Thomson, Peter

2016-04-01

Structural control systems are considered an effective alternative for reducing vibrations in civil structures and are classified according to their energy supply requirement: passive, semi-active, active and hybrid. Commonly used structural control systems in buildings are passive friction dampers, which add energy dissipation through damping mechanisms induced by sliding friction between their surfaces. Semi-Active Variable Friction Dampers (SAVFD) allow the optimum efficiency range of friction dampers to be enhanced by controlling the clamping force in real time. This paper describes the development and performance evaluation of a low-cost SAVFD for the reduction of vibrations of structures subject to earthquakes. The SAVFD and a benchmark structural control test structure were experimentally characterized and analytical models were developed and updated based on the dynamic characterization. Decentralized control algorithms were implemented and tested on a shaking table. Relative displacements and accelerations of the structure controlled with the SAVFD were 80% less than those of the uncontrolled structure

Nonlinear attenuation of S-waves and Love waves within ambient rock

NASA Astrophysics Data System (ADS)

Sleep, Norman H.; Erickson, Brittany A.

2014-04-01

obtain scaling relationships for nonlinear attenuation of S-waves and Love waves within sedimentary basins to assist numerical modeling. These relationships constrain the past peak ground velocity (PGV) of strong 3-4 s Love waves from San Andreas events within Greater Los Angeles, as well as the maximum PGV of future waves that can propagate without strong nonlinear attenuation. During each event, the shaking episode cracks the stiff, shallow rock. Over multiple events, this repeated damage in the upper few hundred meters leads to self-organization of the shear modulus. Dynamic strain is PGV divided by phase velocity, and dynamic stress is strain times the shear modulus. The frictional yield stress is proportional to depth times the effective coefficient of friction. At the eventual quasi-steady self-organized state, the shear modulus increases linearly with depth allowing inference of past typical PGV where rock over the damaged depth range barely reaches frictional failure. Still greater future PGV would cause frictional failure throughout the damaged zone, nonlinearly attenuating the wave. Assuming self-organization has taken place, estimated maximum past PGV within Greater Los Angeles Basins is 0.4-2.6 m s-1. The upper part of this range includes regions of accumulating sediments with low S-wave velocity that may have not yet compacted, rather than having been damaged by strong shaking. Published numerical models indicate that strong Love waves from the San Andreas Fault pass through Whittier Narrows. Within this corridor, deep drawdown of the water table from its currently shallow and preindustrial levels would nearly double PGV of Love waves reaching Downtown Los Angeles.

SeismoGeodesy: Combination of High Rate, Real-time GNSS and Accelerometer Observations and Rapid Seismic Event Notification for Earth Quake Early Warning and Volcano Monitoring

NASA Astrophysics Data System (ADS)

Jackson, Michael; Zimakov, Leonid; Moessmer, Matthias

2015-04-01

Scientific GNSS networks are moving towards a model of real-time data acquisition, epoch-by-epoch storage integrity, and on-board real-time position and displacement calculations. This new paradigm allows the integration of real-time, high-rate GNSS displacement information with acceleration and velocity data to create very high-rate displacement records. The mating of these two instruments allows the creation of a new, very high-rate (200 Hz) displacement observable that has the full-scale displacement characteristics of GNSS and high-precision dynamic motions of seismic technologies. It is envisioned that these new observables can be used for earthquake early warning studies, volcano monitoring, and critical infrastructure monitoring applications. Our presentation will focus on the characteristics of GNSS, seismic, and strong motion sensors in high dynamic environments, including historic earthquakes replicated on a shake table over a range of displacements and frequencies. We will explore the optimum integration of these sensors from a filtering perspective including simple harmonic impulses over varying frequencies and amplitudes and under the dynamic conditions of various earthquake scenarios. We will also explore the tradeoffs between various GNSS processing schemes including real-time precise point positioning (PPP) and real-time kinematic (RTK) as applied to seismogeodesy. In addition we will discuss implementation of a Rapid Seismic Event Notification System that provides quick delivery of digital data from seismic stations to the acquisition and processing center and a full data integrity model for real-time earthquake notification that provides warning prior to significant ground shaking.

ShakeAlert—An earthquake early warning system for the United States west coast

USGS Publications Warehouse

Burkett, Erin R.; Given, Douglas D.; Jones, Lucile M.

2014-08-29

Earthquake early warning systems use earthquake science and the technology of monitoring systems to alert devices and people when shaking waves generated by an earthquake are expected to arrive at their location. The seconds to minutes of advance warning can allow people and systems to take actions to protect life and property from destructive shaking. The U.S. Geological Survey (USGS), in collaboration with several partners, has been working to develop an early warning system for the United States. ShakeAlert, a system currently under development, is designed to cover the West Coast States of California, Oregon, and Washington.

Shaking video stabilization with content completion

NASA Astrophysics Data System (ADS)

Peng, Yi; Ye, Qixiang; Liu, Yanmei; Jiao, Jianbin

2009-01-01

A new stabilization algorithm to counterbalance the shaking motion in a video based on classical Kandade-Lucas- Tomasi (KLT) method is presented in this paper. Feature points are evaluated with law of large numbers and clustering algorithm to reduce the side effect of moving foreground. Analysis on the change of motion direction is also carried out to detect the existence of shaking. For video clips with detected shaking, an affine transformation is performed to warp the current frame to the reference one. In addition, the missing content of a frame during the stabilization is completed with optical flow analysis and mosaicking operation. Experiments on video clips demonstrate the effectiveness of the proposed algorithm.

Probabilistic description of infant head kinematics in abusive head trauma.

PubMed

Lintern, T O; Nash, M P; Kelly, P; Bloomfield, F H; Taberner, A J; Nielsen, P M F

2017-12-01

Abusive head trauma (AHT) is a potentially fatal result of child abuse, but the mechanisms by which injury occur are often unclear. To investigate the contention that shaking alone can elicit the injuries observed, effective computational models are necessary. The aim of this study was to develop a probabilistic model describing infant head kinematics in AHT. A deterministic model incorporating an infant's mechanical properties, subjected to different shaking motions, was developed in OpenSim. A Monte Carlo analysis was used to simulate the range of infant kinematics produced as a result of varying both the mechanical properties and the type of shaking motions. By excluding physically unrealistic shaking motions, worst-case shaking scenarios were simulated and compared to existing injury criteria for a newborn, a 4.5 month-old, and a 12 month-old infant. In none of the three cases were head kinematics observed to exceed previously-estimated subdural haemorrhage injury thresholds. The results of this study provide no biomechanical evidence to demonstrate how shaking by a human alone can cause the injuries observed in AHT, suggesting either that additional factors, such as impact, are required, or that the current estimates of injury thresholds are incorrect.

Experimental and analytical study on vibration control effects of eddy-current tuned mass dampers under seismic excitations

NASA Astrophysics Data System (ADS)

Lu, Zheng; Huang, Biao; Zhang, Qi; Lu, Xilin

2018-05-01

Eddy-current tuned mass dampers (EC-TMDs) are non-contacting passive control devices and are developed on the basis of conventional tuned mass dampers. They comprise a solid mass, a stiffness element, and a damping element, wherein the damping mechanism originates from eddy currents. By relative motion between a non-magnetic conductive metal and a permanent magnet in a dynamic system, a time-varying magnetic field is induced in the conductor, thereby generating eddy currents. The eddy currents induce a magnetic field with opposite polarity, causing repulsive forces, i.e., damping forces. This technology can overcome the drawbacks of conventional tuned mass dampers, such as limited service life, deterioration of mechanical properties, and undesired additional stiffness. The experimental and analytical study of this system installed on a multi-degree-of-freedom structure is presented in this paper. A series of shaking table tests were conducted on a five-story steel-frame model with/without an EC-TMD to evaluate the effectiveness and performance of the EC-TMD in suppressing the vibration of the model under seismic excitations. The experimental results show that the EC-TMD can effectively reduce the displacement response, acceleration response, interstory drift ratio, and maximum strain of the columns under different earthquake excitations. Moreover, an analytical method was proposed on the basis of electromagnetic and structural dynamic theories. A comparison between the test and simulation results shows that the simulation method can be used to estimate the response of structures with an EC-TMD under earthquake excitations with acceptable accuracy.

Electromagnetic tracking (EMT) technology for improved treatment quality assurance in interstitial brachytherapy.

PubMed

Kellermeier, Markus; Herbolzheimer, Jens; Kreppner, Stephan; Lotter, Michael; Strnad, Vratislav; Bert, Christoph

2017-01-01

Electromagnetic Tracking (EMT) is a novel technique for error detection and quality assurance (QA) in interstitial high dose rate brachytherapy (HDR-iBT). The purpose of this study is to provide a concept for data acquisition developed as part of a clinical evaluation study on the use of EMT during interstitial treatment of breast cancer patients. The stability, accuracy, and precision of EMT-determined dwell positions were quantified. Dwell position reconstruction based on EMT was investigated on CT table, HDR table and PDR bed to examine the influence on precision and accuracy in a typical clinical workflow. All investigations were performed using a precise PMMA phantom. The track of catheters inserted in that phantom was measured by manually inserting a 5 degree of freedom (DoF) sensor while recording the position of three 6DoF fiducial sensors on the phantom surface to correct motion influences. From the corrected data, dwell positions were reconstructed along the catheter's track. The accuracy of the EMT-determined dwell positions was quantified by the residual distances to reference dwell positions after using a rigid registration. Precision and accuracy were investigated for different phantom-table and sensor-field generator (FG) distances. The measured precision of the EMT-determined dwell positions was ≤ 0.28 mm (95th percentile). Stability tests showed a drift of 0.03 mm in the first 20 min of use. Sudden shaking of the FG or (large) metallic objects close to the FG degrade the precision. The accuracy with respect to the reference dwell positions was on all clinical tables < 1 mm at 200 mm FG distance and 120 mm phantom-table distance. Phantom measurements showed that EMT-determined localization of dwell positions in HDR-iBT is stable, precise, and sufficiently accurate for clinical assessment. The presented method may be viable for clinical applications in HDR-iBT, like implant definition, error detection or quantification of uncertainties. Further clinical investigations are needed. © 2017 The Authors. Journal of Applied Clinical Medical Physics published by Wiley Periodicals, Inc. on behalf of American Association of Physicists in Medicine.

CISN ShakeAlert: Using early warnings for earthquakes in California

NASA Astrophysics Data System (ADS)

Vinci, M.; Hellweg, M.; Jones, L. M.; Khainovski, O.; Schwartz, K.; Lehrer, D.; Allen, R. M.; Neuhauser, D. S.

2009-12-01

Educated users who have developed response plans and procedures are just as important for an earthquake early warning (EEW) system as are the algorithms and computers that process the data and produce the warnings. In Japan, for example, the implementation of the EEW system which now provides advanced alerts of ground shaking included intense outreach efforts to both institutional and individual recipients. Alerts are now used in automatic control systems that stop trains, place sensitive equipment in safe mode and isolate hazards while the public takes cover. In California, the California Integrated Seismic Network (CISN) is now developing and implementing components of a prototype system for EEW, ShakeAlert. As this processing system is developed, we invite a suite of perspective users from critical industries and institutions throughout California to partner with us in developing useful ShakeAlert products and procedures. At the same time, we will support their efforts to determine and implement appropriate responses to an early warning of earthquake shaking. As a first step, in a collaboration with BART, we have developed a basic system allowing BART’s operation center to receive realtime ground shaking information from more than 150 seismic stations operating in the San Francisco Bay Area. BART engineers are implementing a display system for this information. Later phases will include the development of improved response procedures utilizing this information. We plan to continue this collaboration to include more sophisticated information from the prototype CISN ShakeAlert system.

Effects of different fermentation methods on bacterial cellulose and acid production by Gluconacetobacter xylinus in Cantonese-style rice vinegar.

PubMed

Fu, Liang; Chen, Siqian; Yi, Jiulong; Hou, Zongxia

2014-07-01

A strain of acidogenic bacterium was isolated from the fermentation liquid of Cantonese-style rice vinegar produced by traditional surface fermentation. 16S rDNA identification confirmed the bacterium as Gluconacetobacter xylinus, which synthesizes bacterial cellulose, and the acid productivity of the strain was investigated. In the study, the effects of the membrane integrity and the comparison of the air-liquid interface membrane with immerged membrane on total acidity, cellulose production, alcohol dehydrogenase (ADH) activity and number of bacteria were investigated. The cellulose membrane and the bacteria were observed under SEM for discussing their relationship. The correlations between oxygen consumption and total acid production rate were compared in surface and shake flask fermentation. The results showed the average acid productivity of the strain was 0.02g/(100mL/h), and the integrity of cellulose membrane in surface fermentation had an important effect on total acidity and cellulose production. With a higher membrane integrity, the total acidity after 144 h of fermentation was 3.75 g/100 mL, and the cellulose production was 1.71 g/100 mL after 360 h of fermentation. However, when the membrane was crushed by mechanical force, the total acidity and the cellulose production were as low as 0.36 g/100 mL and 0.14 g/100 mL, respectively. When the cellulose membrane was forced under the surface of fermentation liquid, the total acid production rate was extremely low, but the activity of ADH in the cellulose membrane was basically the same with the one above the liquid surface. The bacteria were mainly distributed in the cellulose membrane during the fermentation. The bacterial counts in surface fermentation were more than in the shake flask fermentation and G. xylinus consumed the substrate faster, in surface fermentation than in shake flask fermentation. The oxygen consumption rate and total acid production rate of surface fermentation were respectively 26.13 times and 2.92 times that of shake flask fermentation.

THE GREAT SOUTHERN CALIFORNIA SHAKEOUT: Earthquake Science for 22 Million People

NASA Astrophysics Data System (ADS)

Jones, L.; Cox, D.; Perry, S.; Hudnut, K.; Benthien, M.; Bwarie, J.; Vinci, M.; Buchanan, M.; Long, K.; Sinha, S.; Collins, L.

2008-12-01

Earthquake science is being communicated to and used by the 22 million residents of southern California to improve resiliency to future earthquakes through the Great Southern California ShakeOut. The ShakeOut began when the USGS partnered with the California Geological Survey, Southern California Earthquake Center and many other organizations to bring 300 scientists and engineers together to formulate a comprehensive description of a plausible major earthquake, released in May 2008, as the ShakeOut Scenario, a description of the impacts and consequences of a M7.8 earthquake on the Southern San Andreas Fault (USGS OFR2008-1150). The Great Southern California ShakeOut was a week of special events featuring the largest earthquake drill in United States history. The ShakeOut drill occurred in houses, businesses, and public spaces throughout southern California at 10AM on November 13, 2008, when southern Californians were asked to pretend that the M7.8 scenario earthquake had occurred and to practice actions that could reduce the impact on their lives. Residents, organizations, schools and businesses registered to participate in the drill through www.shakeout.org where they could get accessible information about the scenario earthquake and share ideas for better reparation. As of September 8, 2008, over 2.7 million confirmed participants had been registered. The primary message of the ShakeOut is that what we do now, before a big earthquake, will determine what our lives will be like after. The goal of the ShakeOut has been to change the culture of earthquake preparedness in southern California, making earthquakes a reality that are regularly discussed. This implements the sociological finding that 'milling,' discussing a problem with loved ones, is a prerequisite to taking action. ShakeOut milling is taking place at all levels from individuals and families, to corporations and governments. Actions taken as a result of the ShakeOut include the adoption of earthquake response technologies by Los Angeles Unified School District and a top to bottom examination of Los Angeles County Fire Department's earthquake response strategies.

Earthquake Early Warning ShakeAlert System: Testing and certification platform

USGS Publications Warehouse

Cochran, Elizabeth S.; Kohler, Monica D.; Given, Douglas; Guiwits, Stephen; Andrews, Jennifer; Meier, Men-Andrin; Ahmad, Mohammad; Henson, Ivan; Hartog, Renate; Smith, Deborah

2017-01-01

Earthquake early warning systems provide warnings to end users of incoming moderate to strong ground shaking from earthquakes. An earthquake early warning system, ShakeAlert, is providing alerts to beta end users in the western United States, specifically California, Oregon, and Washington. An essential aspect of the earthquake early warning system is the development of a framework to test modifications to code to ensure functionality and assess performance. In 2016, a Testing and Certification Platform (TCP) was included in the development of the Production Prototype version of ShakeAlert. The purpose of the TCP is to evaluate the robustness of candidate code that is proposed for deployment on ShakeAlert Production Prototype servers. TCP consists of two main components: a real‐time in situ test that replicates the real‐time production system and an offline playback system to replay test suites. The real‐time tests of system performance assess code optimization and stability. The offline tests comprise a stress test of candidate code to assess if the code is production ready. The test suite includes over 120 events including local, regional, and teleseismic historic earthquakes, recentering and calibration events, and other anomalous and potentially problematic signals. Two assessments of alert performance are conducted. First, point‐source assessments are undertaken to compare magnitude, epicentral location, and origin time with the Advanced National Seismic System Comprehensive Catalog, as well as to evaluate alert latency. Second, we describe assessment of the quality of ground‐motion predictions at end‐user sites by comparing predicted shaking intensities to ShakeMaps for historic events and implement a threshold‐based approach that assesses how often end users initiate the appropriate action, based on their ground‐shaking threshold. TCP has been developed to be a convenient streamlined procedure for objectively testing algorithms, and it has been designed with flexibility to accommodate significant changes in development of new or modified system code. It is expected that the TCP will continue to evolve along with the ShakeAlert system, and the framework we describe here provides one example of how earthquake early warning systems can be evaluated.

National fire-danger rating system fine-fuel moisture content tables—an Alaskan adaptation.

Treesearch

Richard J. Barney

1969-01-01

Fine-fuel moisture content tables, using dry bulb and dewpoint temperatures as entry data, have been developed for use with the National Fire-Danger Rating System in Alaska. Comparisons have been made which illustrate differences resulting from danger-rating calculations based on these new fine-fuel moisture content tables for the cured, transition, and green...

Forest statistics for Southwest-North Alabama counties - 1990

Treesearch

William H. McWilliams; Patrick E. Miller; John S. Vissage

1990-01-01

Tabulated results were derived from data obtained during a recent forest inventory of southwest-North Alabama (fig. I). Core tables (1 to 25) are compatible among Forest Inventory and Analysis units in the Eastern U.S. Other tables (26 to 43) supplement the information contained in the core tables. Comparisons are made between results of the 1990 inventory and previous...

Modeling Second Language Change Using Skill Retention Theory

DTIC Science & Technology

2013-06-01

xiv LIST OF TABLES Table 1. ILR and ACTFL Scale Comparison (From SIL International, 1999) ................5 Table 2. Metacognitive Learning Strategy...meaningful. • Speaking and writing are productive skill and require that a linguist actively produce information to be conveyed. E. RESEARCH...before productive skills (speaking and writing ) and attrition of these skills takes place in reverse order (Hansen & Reetz-Kurashige, 1999). Hansen

Lessons Learned from Creating the Public Earthquake Resource Center at CERI

NASA Astrophysics Data System (ADS)

Patterson, G. L.; Michelle, D.; Johnston, A.

2004-12-01

The Center for Earthquake Research and Information (CERI) at the University of Memphis opened the Public Earthquake Resource Center (PERC) in May 2004. The PERC is an interactive display area that was designed to increase awareness of seismology, Earth Science, earthquake hazards, and earthquake engineering among the general public and K-12 teachers and students. Funding for the PERC is provided by the US Geological Survey, The NSF-funded Mid America Earthquake Center, and the University of Memphis, with input from the Incorporated Research Institutions for Seismology. Additional space at the facility houses local offices of the US Geological Survey. PERC exhibits are housed in a remodeled residential structure at CERI that was donated by the University of Memphis and the State of Tennessee. Exhibits were designed and built by CERI and US Geological Survey staff and faculty with the help of experienced museum display subcontractors. The 600 square foot display area interactively introduces the basic concepts of seismology, real-time seismic information, seismic network operations, paleoseismology, building response, and historical earthquakes. Display components include three 22" flat screen monitors, a touch sensitive monitor, 3 helicorder elements, oscilloscope, AS-1 seismometer, life-sized liquefaction trench, liquefaction shake table, and building response shake table. All displays include custom graphics, text, and handouts. The PERC website at www.ceri.memphis.edu/perc also provides useful information such as tour scheduling, ask a geologist, links to other institutions, and will soon include a virtual tour of the facility. Special consideration was given to address State science standards for teaching and learning in the design of the displays and handouts. We feel this consideration is pivotal to the success of any grass roots Earth Science education and outreach program and represents a valuable lesson that has been learned at CERI over the last several years. Another critical lesson that has been learned is to employ K-12 education professionals and utilize undergrad and graduate student workers in the University's Department of Education. Such staff members are keenly aware of the pressures and needs in diverse communities such as Shelby County, Tennessee and are uniquely suited to design and implement new and innovative programs that provide substantive short-term user benefits and promote long-term relationships with the K-12 teachers, students, and teacher's organizations.

Combination of High Rate, Real-time GNSS and Accelerometer Observations - Preliminary Results Using a Shake Table and Historic Earthquake Events.

NASA Astrophysics Data System (ADS)

Jackson, Michael; Passmore, Paul; Zimakov, Leonid; Raczka, Jared

2014-05-01

One of the fundamental requirements of an Earthquake Early Warning (EEW) system (and other mission critical applications) is to quickly detect and process the information from the strong motion event, i.e. event detection and location, magnitude estimation, and the peak ground motion estimation at the defined targeted site, thus allowing the civil protection authorities to provide pre-programmed emergency response actions: Slow down or stop rapid transit trains and high-speed trains; shutoff of gas pipelines and chemical facilities; stop elevators at the nearest floor; send alarms to hospitals, schools and other civil institutions. An important question associated with the EEW system is: can we measure displacements in real time with sufficient accuracy? Scientific GNSS networks are moving towards a model of real-time data acquisition, storage integrity, and real-time position and displacement calculations. This new paradigm allows the integration of real-time, high-rate GNSS displacement information with acceleration and velocity data to create very high-rate displacement records. The mating of these two instruments allows the creation of a new, very high-rate (200 Hz) displacement observable that has the full-scale displacement characteristics of GNSS and high-precision dynamic motions of seismic technologies. It is envisioned that these new observables can be used for earthquake early warning studies and other mission critical applications, such as volcano monitoring, building, bridge and dam monitoring systems. REF TEK a Division of Trimble has developed the integrated GNSS/Accelerograph system, model 160-09SG, which consists of REF TEK's fourth generation electronics, a 147-01 high-resolution ANSS Class A accelerometer, and Trimble GNSS receiver and antenna capable of real time, on board Precise Point Positioning (PPP) techniques with satellite clock and orbit corrections delivered to the receiver directly via L-band satellite communications. The test we conducted with the 160-09SG Recorder is focused on the characteristics of GNSS and seismic sensors in high dynamic environments, including historic earthquakes replicated on a shake table, over a range of displacements and frequencies. The main goals of the field tests are to explore the optimum integration of these sensors from a filtering perspective including simple harmonic impulses over varying frequencies and amplitudes and under the dynamic conditions of various earthquake scenarios.

The Sidebar Computer Program, a seismic-shaking intensity meter: users' manual and software description

USGS Publications Warehouse

Evans, John R.

2003-01-01

The SideBar computer program provides a visual display of seismic shaking intensity as recorded at one specific seismograph. This software allows a user to tap into the seismic data recorded on that specific seismograph and to display the overall level of shaking at the single location where that seismograph resides (usually the same place the user is). From this shaking level, SideBar also estimates the potential for damage nearby. SideBar cannot tell you the “Richter magnitude” of the earthquake (see box), only how hard the ground shook locally and this estimate of how much damage is likely in the neighborhood. This combination of local effects is called the “seismic intensity”. SideBar runs on a standard desktop or laptop PC, and is intended for the media, schools, emergency responders, and any other group hosting a seismograph and who want to know immediately after an earthquake the levels of shaking measured by that instrument. These local values can be used to inform the public and help initiate appropriate local emergency response activities in the minutes between the earthquake and availability of the broader coverage provided by the USGS over the Web, notably by ShakeMap. For example, for instruments installed in schools, the level of shaking and likely damage at the school could immediately be Web broadcast and parents could quickly determine the likely safety of their children—their biggest postearthquake concern. Also, in the event of a Web outage, SideBar may be a continuing primary source of local emergency response information for some additional minutes. Specifically, SideBar interprets the peak level of acceleration (that is, the force of shaking, as a percentage of the force of gravity) as well as the peak velocity, or highest speed, at which the ground moves. Using these two basic measurements, SideBar computes what is called Instrumental Intensity—a close approximation of the Modified Mercalli Intensity scale, or “MMI” (using the Wald et al., 1999a, relationships between acceleration, velocity, and shaking intensity). Intensity is a measure of local shaking strength and the potential for damage—of how bad the earthquake effects were locally. The intensity level is what SideBar displays most prominently on the PC monitor. Intensity is shown as a large, colored bar that gets taller and changes color up a rainbow from blues toward reds as the shaking level increases. As opposed to earthquake magnitudes, which are reported as decimal values (like “7.6”), intensity is traditionally given as a Roman numeral, with “I” to “X+” assigned to levels of potential damage and perceived shaking strength. For good measure, SideBar shows the actual values of the force of shaking (peak ground acceleration as a percentage of gravity) and the speed of ground motion (peak ground velocity in inches per second, by default, or in centimeters per second, if you wish), both these values as decimal numbers. SideBar also remembers the most recent earthquakes (for up to one week), and can store as many of these previous earthquakes as the user allows (and as the user’s PC has room for)—typically thousands. SideBar also remembers forever the three largest earthquakes it has seen and all earthquakes over intensity IV so that one never loses particularly important events.

Preparing for a "Big One": The great southern California shakeout

USGS Publications Warehouse

Jones, L.M.; Benthien, M.

2011-01-01

The Great Southern California ShakeOut was a week of special events featuring the largest earthquake drill in United States history. On November 13, 2008, over 5 million Southern Californians pretended that the magnitude-7.8 ShakeOut scenario earthquake was occurring and practiced actions derived from results of the ShakeOut Scenario, to reduce the impact of a real, San Andreas Fault event. The communications campaign was based on four principles: 1) consistent messaging from multiple sources; 2) visual reinforcement: 3) encouragement of "milling"; and 4) focus on concrete actions. The goals of the Shake-Out established in Spring 2008 were: 1) to register 5 million people to participate in the drill; 2) to change the culture of earthquake preparedness in Southern California; and 3) to reduce earthquake losses in Southern California. Over 90% of the registrants surveyed the next year reported improvement in earthquake preparedness at their organization as a result of the ShakeOut. ?? 2011, Earthquake Engineering Research Institute.

Seismic shaking in the North China Basin expected from ruptures of a possible seismic gap

NASA Astrophysics Data System (ADS)

Duan, Benchun; Liu, Dunyu; Yin, An

2017-05-01

A 160 km long seismic gap, which has not been ruptured over 8000 years, was identified recently in North China. In this study, we use a dynamic source model and a newly available high-resolution 3-D velocity structure to simulate long-period ground motion (up to 0.5 Hz) from possibly worst case rupture scenarios of the seismic gap. We find that the characteristics of the earthquake source and the local geologic structure play a critical role in controlling the amplitude and distribution of the simulated strong ground shaking. Rupture directivity and slip asperities can result in large-amplitude (i.e., >1 m/s) ground shaking near the fault, whereas long-duration shaking may occur within sedimentary basins. In particular, a deep and closed Quaternary basin between Beijing and Tianjin can lead to ground shaking of several tens of cm/s for more than 1 min. These results may provide a sound basis for seismic mitigation in one of the most populated regions in the world.

MyShake: Initial observations from a global smartphone seismic network

NASA Astrophysics Data System (ADS)

Kong, Qingkai; Allen, Richard M.; Schreier, Louis

2016-09-01

MyShake is a global smartphone seismic network that harnesses the power of crowdsourcing. In the first 6 months since the release of the MyShake app, there were almost 200,000 downloads. On a typical day about 8000 phones provide acceleration waveform data to the MyShake archive. The on-phone app can detect and trigger on P waves and is capable of recording magnitude 2.5 and larger events. More than 200 seismic events have been recorded so far, including events in Chile, Argentina, Mexico, Morocco, Nepal, New Zealand, Taiwan, Japan, and across North America. The largest number of waveforms from a single earthquake to date comes from the M5.2 Borrego Springs earthquake in Southern California, for which MyShake collected 103 useful three-component waveforms. The network continues to grow with new downloads from the Google Play store everyday and expands rapidly when public interest in earthquakes peaks such as during an earthquake sequence.

Specific Signature of Seismic Shaking in Landslide Inventories: Case of the Chichi Earthquake

NASA Astrophysics Data System (ADS)

Meunier, P.; Rault, C.; Marc, O.; Hovius, N.

2017-12-01

The 1999 Chichi earthquake triggered 10 000 landslides in its epicentral area. In addition to coseismic landsliding, directly induced by the shaking, the hillslopes response extended to several years after the main shock, during which landslide susceptibility remained higher than during the pre-seismic period. We attribute this elevated rate to weakening effects caused by the shaking. The characteristics of the coseismic landslide catalogues (clustering,slope and azimuth distribution) bears the signature of the seismic triggering. Extended landslide mapping (1994-2004) allows to track changes in these signatures in order to better interpret them. We present a summary of the change of these signatures through time and space. At the scale of the epicentral area, we show that coseismic landslide clustering did clearly occur along the fault where the shaking is strong. In 3 sub-catchments of the Choshui river, a finer analysis of the landslide time series reveals a mixed signature of both geology and shaking. Pre-quake rain-induced landslides preferentially occurred down slope and along the bedding planes while coseismic landslides locate higher in the landscape, on slopes strongly affected by site effects. However, during the post seismic period, the signature of the shaking is not present while landslide rate remains high, suggesting that weakening effects seemed homogeneously distributed in the landscape.

Earthquake early Warning ShakeAlert system: West coast wide production prototype

USGS Publications Warehouse

Kohler, Monica D.; Cochran, Elizabeth S.; Given, Douglas; Guiwits, Stephen; Neuhauser, Doug; Hensen, Ivan; Hartog, Renate; Bodin, Paul; Kress, Victor; Thompson, Stephen; Felizardo, Claude; Brody, Jeff; Bhadha, Rayo; Schwarz, Stan

2017-01-01

Earthquake early warning (EEW) is an application of seismological science that can give people, as well as mechanical and electrical systems, up to tens of seconds to take protective actions before peak earthquake shaking arrives at a location. Since 2006, the U.S. Geological Survey has been working in collaboration with several partners to develop EEW for the United States. The goal is to create and operate an EEW system, called ShakeAlert, for the highest risk areas of the United States, starting with the West Coast states of California, Oregon, and Washington. In early 2016, the Production Prototype v.1.0 was established for California; then, in early 2017, v.1.2 was established for the West Coast, with earthquake notifications being distributed to a group of beta users in California, Oregon, and Washington. The new ShakeAlert Production Prototype was an outgrowth from an earlier demonstration EEW system that began sending test notifications to selected users in California in January 2012. ShakeAlert leverages the considerable physical, technical, and organizational earthquake monitoring infrastructure of the Advanced National Seismic System, a nationwide federation of cooperating seismic networks. When fully implemented, the ShakeAlert system may reduce damage and injury caused by large earthquakes, improve the nation’s resilience, and speed recovery.

Specific signature of seismic shaking in landslide catalogues: Case of the Chichi earthquake

NASA Astrophysics Data System (ADS)

Meunier, Patrick; Rault, Claire; Marc, Odin; Hovius, Niels

2017-04-01

The 1999 Chichi earthquake triggered 10 000 landslides in its epicentral area. In addition to coseismic landsliding, directly induced by the shaking, the hillslopes response extended to several years after the main shock, during which landslide susceptibility remained higher than during the pre-seismic period. We attribute this elevated rate to weakening effects caused by the shaking. The characteristics of the coseismic landslide catalogues (clustering, slope and azimuth distribution) bears the signature of the seismic triggering. Extended landslide mapping (1994-2004) allows to track changes in these signatures in order to better interpret them. We present a summary of the change of these signatures through time and space. At the scale of the epicentral area, we show that coseismic landslide clustering did clearly occur along the fault where the shaking is strong. In 3 sub-catchments of the Choshui river, a finer analysis of the landslide time series reveals a mixed signature of both geology and shaking. Pre-quake rain-induced landslides preferentially occurred down slope and along the bedding planes while coseismic landslides locate higher in the landscape, on slopes strongly affected by site effects. However, during the post seismic period, the signature of the shaking is not present while landslide rate remains high, suggesting that weakening effects seemed homogeneously distributed in the landscape.

Optical and Thermal Behaviors of Plasmonic Bowtie Aperture and Its NSOM Characterization for Heat-Assisted Magnetic Recording

DTIC Science & Technology

2016-02-01

NFT), plasmonic materials, scattering-type scanning near-field optical microscopy (s-NSOM). I . INTRODUCTION THE continuous growth in data storage is...recording stack for (a) gold and (b) silver bowtie apertures. The spatial distributions are calculated at 1 ns. TABLE I COMPARISON BETWEEN GOLD AND SILVER...NFTs From the calculation results, we can obtain the thermal efficiency defined in (1). A detailed comparison is summarized in Table I , where the

Linking ShakeMap and Emergency Managers in the Utah Region

NASA Astrophysics Data System (ADS)

Pankow, K.; Bausch, D.; Carey, B.

2007-12-01

In 2001, the University of Utah Seismograph Stations (UUSS) locally customized and began producing automatic ShakeMaps in Utah's Wasatch Front urban corridor as part of a new real-time earthquake information system developed under the Advanced National Seismic System. In 2005, motivated by requests from Utah's Division of Homeland Security and FEMA, ShakeMap capabilities were expanded to cover the entire Utah region. Now in 2007, ShakeMap capabilities throughout the region will again be enhanced by increased station coverage. The increased station coverage comes both from permanent stations funded by a state initiative and from the temporary deployment of EarthScope USArray stations. The state initiative will add ~22 strong-motion instruments and ~10 broadband instruments to the UUSS network. The majority of these stations will be located in southwestern Utah--one of the fastest growing regions in the U.S. EarthScope will evenly distribute 70 broadband stations in the region during 2007 that will be removed after 18 to 24 months. In addition to the enhanced station coverage for producing ShakeMaps in the Utah region, the transfer of information to the emergency response community is also being enhanced. First, tools are being developed that will link ShakeMap data with HAZUS loss-estimation software in near-real-time for rapid impact assessment. Second, ShakeMap scenarios are being used in conjunction with HAZUS loss-estimation software to produce customized maps for planning and preparedness exercises and also for developing templates that can be used following a significant regional earthquake. With the improvements to ShakeMap and the improved dialogue with the emergency managers, a suite of maps and information products were developed based on scenario earthquakes for training and exercise purposes. These products will be available in a timely fashion following a significant earthquake in the Utah region.

A Simple Algorithm for Predicting Bacteremia Using Food Consumption and Shaking Chills: A Prospective Observational Study.

PubMed

Komatsu, Takayuki; Takahashi, Erika; Mishima, Kentaro; Toyoda, Takeo; Saitoh, Fumihiro; Yasuda, Akari; Matsuoka, Joe; Sugita, Manabu; Branch, Joel; Aoki, Makoto; Tierney, Lawrence; Inoue, Kenji

2017-07-01

Predicting the presence of true bacteremia based on clinical examination is unreliable. We aimed to construct a simple algorithm for predicting true bacteremia by using food consumption and shaking chills. A prospective multicenter observational study. Three hospital centers in a large Japanese city. In total, 1,943 hospitalized patients aged 14 to 96 years who underwent blood culture acquisitions between April 2013 and August 2014 were enrolled. Patients with anorexia-inducing conditions were excluded. We assessed the patients' oral food intake based on the meal immediately prior to the blood culture with definition as "normal food consumption" when >80% of a meal was consumed and "poor food consumption" when <80% was consumed. We also concurrently evaluated for a history of shaking chills. We calculated the statistical characteristics of food consumption and shaking chills for the presence of true bacteremia, and subsequently built the algorithm by using recursive partitioning analysis. Among 1,943 patients, 223 cases were true bacteremia. Among patients with normal food consumption, without shaking chills, the incidence of true bacteremia was 2.4% (13/552). Among patients with poor food consumption and shaking chills, the incidence of true bacteremia was 47.7% (51/107). The presence of poor food consumption had a sensitivity of 93.7% (95% confidence interval [CI], 89.4%-97.9%) for true bacteremia, and the absence of poor food consumption (ie, normal food consumption) had a negative likelihood ratio (LR) of 0.18 (95% CI, 0.17-0.19) for excluding true bacteremia, respectively. Conversely, the presence of the shaking chills had a specificity of 95.1% (95% CI, 90.7%-99.4%) and a positive LR of 4.78 (95% CI, 4.56-5.00) for true bacteremia. A 2-item screening checklist for food consumption and shaking chills had excellent statistical properties as a brief screening instrument for predicting true bacteremia. © 2017 Society of Hospital Medicine

CyberShake-derived ground-motion prediction models for the Los Angeles region with application to earthquake early warning

USGS Publications Warehouse

Bose, Maren; Graves, Robert; Gill, David; Callaghan, Scott; Maechling, Phillip J.

2014-01-01

Real-time applications such as earthquake early warning (EEW) typically use empirical ground-motion prediction equations (GMPEs) along with event magnitude and source-to-site distances to estimate expected shaking levels. In this simplified approach, effects due to finite-fault geometry, directivity and site and basin response are often generalized, which may lead to a significant under- or overestimation of shaking from large earthquakes (M > 6.5) in some locations. For enhanced site-specific ground-motion predictions considering 3-D wave-propagation effects, we develop support vector regression (SVR) models from the SCEC CyberShake low-frequency (<0.5 Hz) and broad-band (0–10 Hz) data sets. CyberShake encompasses 3-D wave-propagation simulations of >415 000 finite-fault rupture scenarios (6.5 ≤ M ≤ 8.5) for southern California defined in UCERF 2.0. We use CyberShake to demonstrate the application of synthetic waveform data to EEW as a ‘proof of concept’, being aware that these simulations are not yet fully validated and might not appropriately sample the range of rupture uncertainty. Our regression models predict the maximum and the temporal evolution of instrumental intensity (MMI) at 71 selected test sites using only the hypocentre, magnitude and rupture ratio, which characterizes uni- and bilateral rupture propagation. Our regression approach is completely data-driven (where here the CyberShake simulations are considered data) and does not enforce pre-defined functional forms or dependencies among input parameters. The models were established from a subset (∼20 per cent) of CyberShake simulations, but can explain MMI values of all >400 k rupture scenarios with a standard deviation of about 0.4 intensity units. We apply our models to determine threshold magnitudes (and warning times) for various active faults in southern California that earthquakes need to exceed to cause at least ‘moderate’, ‘strong’ or ‘very strong’ shaking in the Los Angeles (LA) basin. These thresholds are used to construct a simple and robust EEW algorithm: to declare a warning, the algorithm only needs to locate the earthquake and to verify that the corresponding magnitude threshold is exceeded. The models predict that a relatively moderate M6.5–7 earthquake along the Palos Verdes, Newport-Inglewood/Rose Canyon, Elsinore or San Jacinto faults with a rupture propagating towards LA could cause ‘very strong’ to ‘severe’ shaking in the LA basin; however, warning times for these events could exceed 30 s.

An Atlas of ShakeMaps for Landslide and Liquefaction Modeling

NASA Astrophysics Data System (ADS)

Johnson, K. L.; Nowicki, M. A.; Mah, R. T.; Garcia, D.; Harp, E. L.; Godt, J. W.; Lin, K.; Wald, D. J.

2012-12-01

The human consequences of a seismic event are often a result of subsequent hazards induced by the earthquake, such as landslides. While the United States Geological Survey (USGS) ShakeMap and Prompt Assessment of Global Earthquakes for Response (PAGER) systems are, in conjunction, capable of estimating the damage potential of earthquake shaking in near-real time, they do not currently provide estimates for the potential of further damage by secondary processes. We are developing a sound basis for providing estimates of the likelihood and spatial distribution of landslides for any global earthquake under the PAGER system. Here we discuss several important ingredients in this effort. First, we report on the development of a standardized hazard layer from which to calibrate observed landslide distributions; in contrast, prior studies have used a wide variety of means for estimating the hazard input. This layer now takes the form of a ShakeMap, a standardized approach for computing geospatial estimates for a variety of shaking metrics (both peak ground motions and shaking intensity) from any well-recorded earthquake. We have created ShakeMaps for about 20 historical landslide "case history" events, significant in terms of their landslide occurrence, as part of an updated release of the USGS ShakeMap Atlas. We have also collected digitized landslide data from open-source databases for many of the earthquake events of interest. When these are combined with up-to-date topographic and geologic maps, we have the basic ingredients for calibrating landslide probabilities for a significant collection of earthquakes. In terms of modeling, rather than focusing on mechanistic models of landsliding, we adopt a strictly statistical approach to quantify landslide likelihood. We incorporate geology, slope, peak ground acceleration, and landslide data as variables in a logistic regression, selecting the best explanatory variables given the standardized new hazard layers (see Nowicki et al., this meeting, for more detail on the regression). To make the ShakeMap and PAGER systems more comprehensive in terms of secondary losses, we are working to calibrate a similarly constrained regression for liquefaction estimation using a suite of well-studied earthquakes for which detailed, digitized liquefaction datasets are available; here variants of wetness index and soil strength replace geology and slope. We expect that this Atlas of ShakeMaps for landslide and liquefaction case history events, which will soon be publicly available via the internet, will aid in improving the accuracy of loss-modeling systems such as PAGER, as well as allow for a common framework for numerous other mechanistic and empirical studies.

Comparison of stratified and non-stratified most similar neighbour imputation for estimating stand tables

Treesearch

Bianca N. I. Eskelson; Hailemariam Temesgen; Tara M. Barrett

2008-01-01

Many growth and yield simulators require a stand table or tree-list to set the initial condition for projections in time. Most similar neighbour (MSN) approaches can be used for estimating stand tables from information commonly available on forest cover maps (e.g. height, volume, canopy cover, and species composition). Simulations were used to compare MSN (using an...

Direct Lattice Shaking of Bose Condensates: Finite Momentum Superfluids

DOE PAGES

Anderson, Brandon M.; Clark, Logan W.; Crawford, J

2017-05-31

Here, we address band engineering in the presence of periodic driving by numerically shaking a lattice containing a bosonic condensate. By not restricting to simplified band structure models we are able to address arbitrary values of the shaking frequency, amplitude, and interaction strengths g. For "near-resonant" shaking frequencies with moderate g, a quantum phase transition to a finite momentum superfluid is obtained with Kibble-Zurek scaling and quantitative agreement with experiment. We use this successful calibration as a platform to support a more general investigation of the interplay between (one particle) Floquet theory and the effects associated with arbitrary g. Bandmore » crossings lead to superfluid destabilization, but where this occurs depends on g in a complicated fashion.« less

Elders Point East Marsh Island Restoration Monitoring Data Analysis

DTIC Science & Technology

2017-09-21

Figure 13. Average biomass comparison between fertilizer treatment and non- fertilizer treatment at Elders East...25 ERDC/EL CR-17-1 vi Table 5. Count of benthic organisms ...31 Table 6. Benthic Community Indices: True Taxa Richness, Total Organism Count

Toward uniform probabilistic seismic hazard assessments for Southeast Asia

NASA Astrophysics Data System (ADS)

Chan, C. H.; Wang, Y.; Shi, X.; Ornthammarath, T.; Warnitchai, P.; Kosuwan, S.; Thant, M.; Nguyen, P. H.; Nguyen, L. M.; Solidum, R., Jr.; Irsyam, M.; Hidayati, S.; Sieh, K.

2017-12-01

Although most Southeast Asian countries have seismic hazard maps, various methodologies and quality result in appreciable mismatches at national boundaries. We aim to conduct a uniform assessment across the region by through standardized earthquake and fault databases, ground-shaking scenarios, and regional hazard maps. Our earthquake database contains earthquake parameters obtained from global and national seismic networks, harmonized by removal of duplicate events and the use of moment magnitude. Our active-fault database includes fault parameters from previous studies and from the databases implemented for national seismic hazard maps. Another crucial input for seismic hazard assessment is proper evaluation of ground-shaking attenuation. Since few ground-motion prediction equations (GMPEs) have used local observations from this region, we evaluated attenuation by comparison of instrumental observations and felt intensities for recent earthquakes with predicted ground shaking from published GMPEs. We then utilize the best-fitting GMPEs and site conditions into our seismic hazard assessments. Based on the database and proper GMPEs, we have constructed regional probabilistic seismic hazard maps. The assessment shows highest seismic hazard levels near those faults with high slip rates, including the Sagaing Fault in central Myanmar, the Sumatran Fault in Sumatra, the Palu-Koro, Matano and Lawanopo Faults in Sulawesi, and the Philippine Fault across several islands of the Philippines. In addition, our assessment demonstrates the important fact that regions with low earthquake probability may well have a higher aggregate probability of future earthquakes, since they encompass much larger areas than the areas of high probability. The significant irony then is that in areas of low to moderate probability, where building codes are usually to provide less seismic resilience, seismic risk is likely to be greater. Infrastructural damage in East Malaysia during the 2015 Sabah earthquake offers a case in point.

Using safety inspection data to estimate shaking intensity for the 1994 Northridge earthquake

USGS Publications Warehouse

Thywissen, K.; Boatwright, J.

1998-01-01

We map the shaking intensity suffered in Los Angeles County during the 17 January 1994, Northridge earthquake using municipal safety inspection data. The intensity is estimated from the number of buildings given red, yellow, or green tags, aggregated by census tract. Census tracts contain from 200 to 4000 residential buildings and have an average area of 6 km2 but are as small as 2 and 1 km2 in the most densely populated areas of the San Fernando Valley and downtown Los Angeles, respectively. In comparison, the zip code areas on which standard MMI intensity estimates are based are six times larger, on average, than the census tracts. We group the buildings by age (before and after 1940 and 1976), by number of housing units (one, two to four, and five or more), and by construction type, and we normalize the tags by the total number of similar buildings in each census tract. We analyze the seven most abundant building categories. The fragilities (the fraction of buildings in each category tagged within each intensity level) for these seven building categories are adjusted so that the intensity estimates agree. We calibrate the shaking intensity to correspond with the modified Mercalli intensities (MMI) estimated and compiled by Dewey et al. (1995); the shapes of the resulting isoseismals are similar, although we underestimate the extent of the MMI = 6 and 7 areas. The fragility varies significantly between different building categories (by factors of 10 to 20) and building ages (by factors of 2 to 6). The post-1940 wood-frame multi-family (???5 units) dwellings make up the most fragile building category, and the post-1940 wood-frame single-family dwellings make up the most resistant building category.

Using structural damage statistics to derive macroseismic intensity within the Kathmandu valley for the 2015 M7.8 Gorkha, Nepal earthquake

NASA Astrophysics Data System (ADS)

McGowan, S. M.; Jaiswal, K. S.; Wald, D. J.

2017-09-01

We make and analyze structural damage observations from within the Kathmandu valley following the 2015 M7.8 Gorkha, Nepal earthquake to derive macroseismic intensities at several locations including some located near ground motion recording sites. The macroseismic intensity estimates supplement the limited strong ground motion data in order to characterize the damage statistics. This augmentation allows for direct comparisons between ground motion amplitudes and structural damage characteristics and ultimately produces a more constrained ground shaking hazard map for the Gorkha earthquake. For systematic assessments, we focused on damage to three specific building categories: (a) low/mid-rise reinforced concrete frames with infill brick walls, (b) unreinforced brick masonry bearing walls with reinforced concrete slabs, and (c) unreinforced brick masonry bearing walls with partial timber framing. Evaluating dozens of photos of each construction type, assigning each building in the study sample to a European Macroseismic Scale (EMS)-98 Vulnerability Class based upon its structural characteristics, and then individually assigning an EMS-98 Damage Grade to each building allows a statistically derived estimate of macroseismic intensity for each of nine study areas in and around the Kathmandu valley. This analysis concludes that EMS-98 macroseismic intensities for the study areas from the Gorkha mainshock typically were in the VII-IX range. The intensity assignment process described is more rigorous than the informal approach of assigning intensities based upon anecdotal media or first-person accounts of felt-reports, shaking, and their interpretation of damage. Detailed EMS-98 macroseismic assessments in urban areas are critical for quantifying relations between shaking and damage as well as for calibrating loss estimates. We show that the macroseismic assignments made herein result in fatality estimates consistent with the overall and district-wide reported values.

Using structural damage statistics to derive macroseismic intensity within the Kathmandu valley for the 2015 M7.8 Gorkha, Nepal earthquake

USGS Publications Warehouse

McGowan, Sean; Jaiswal, Kishor; Wald, David J.

2017-01-01

We make and analyze structural damage observations from within the Kathmandu valley following the 2015 M7.8 Gorkha, Nepal earthquake to derive macroseismic intensities at several locations including some located near ground motion recording sites. The macroseismic intensity estimates supplement the limited strong ground motion data in order to characterize the damage statistics. This augmentation allows for direct comparisons between ground motion amplitudes and structural damage characteristics and ultimately produces a more constrained ground shaking hazard map for the Gorkha earthquake. For systematic assessments, we focused on damage to three specific building categories: (a) low/mid-rise reinforced concrete frames with infill brick walls, (b) unreinforced brick masonry bearing walls with reinforced concrete slabs, and (c) unreinforced brick masonry bearing walls with partial timber framing. Evaluating dozens of photos of each construction type, assigning each building in the study sample to a European Macroseismic Scale (EMS)-98 Vulnerability Class based upon its structural characteristics, and then individually assigning an EMS-98 Damage Grade to each building allows a statistically derived estimate of macroseismic intensity for each of nine study areas in and around the Kathmandu valley. This analysis concludes that EMS-98 macroseismic intensities for the study areas from the Gorkha mainshock typically were in the VII–IX range. The intensity assignment process described is more rigorous than the informal approach of assigning intensities based upon anecdotal media or first-person accounts of felt-reports, shaking, and their interpretation of damage. Detailed EMS-98 macroseismic assessments in urban areas are critical for quantifying relations between shaking and damage as well as for calibrating loss estimates. We show that the macroseismic assignments made herein result in fatality estimates consistent with the overall and district-wide reported values.

Comparison of two self-directed weight loss interventions: Limited weekly support vs. no outside support.

PubMed

Smith, Bryan K; Van Walleghen, Emily L; Cook-Wiens, Galen; Martin, Rachael N; Curry, Chelsea R; Sullivan, Debra K; Gibson, Cheryl A; Donnelly, Joseph E

2009-08-01

The purpose of this study was to compare the efficacy of two home-based weight loss interventions that differ only in the amount of outside support provided. This was a 12-week, randomized, controlled trial. One group received limited support (LWS, n = 35) via a single 10 min phone call each week while another group received no weekly support (NWS, n = 28). Both the LWS and NWS received pre-packaged meals (PM) and shakes. A third group served as control (CON, n = 30) and received no components of the intervention. Weight loss at 12 weeks was the primary outcome. Diet (PM, shake, and fruit/vegetable (F/V) intake) and physical activity (PA) were self-monitored, recorded daily and reported weekly. An exit survey was completed by participants in the intervention groups upon completion of the study. Weight loss and percent weight loss in the LWS, NWS, and CON groups were 7.7 ± 4.4 kg (8.5 ± 4.2%), 5.9 ± 4.1 kg (6.0 ± 4.2%), and 0.3 ± 1.9 kg (0.4 ± 1.2%), respectively. The decrease in body weight and percent weight loss was significantly greater in the LWS and NWS groups when compared to the CON group and the percent weight loss was significantly greater in the LWS when compared to both the NWS and CON groups. A home-based weight loss program utilizing PM and shakes results in clinically significant percent weight loss and the addition of a brief weekly call promotes additional percent weight loss. © 2009 Asian Oceanian Association for the Study of Obesity . Published by Elsevier Ltd. All rights reserved.

TabPath: interactive tables for metabolic pathway analysis.

PubMed

Moraes, Lauro Ângelo Gonçalves de; Felestrino, Érica Barbosa; Assis, Renata de Almeida Barbosa; Matos, Diogo; Lima, Joubert de Castro; Lima, Leandro de Araújo; Almeida, Nalvo Franco; Setubal, João Carlos; Garcia, Camila Carrião Machado; Moreira, Leandro Marcio

2018-03-15

Information about metabolic pathways in a comparative context is one of the most powerful tool to help the understanding of genome-based differences in phenotypes among organisms. Although several platforms exist that provide a wealth of information on metabolic pathways of diverse organisms, the comparison among organisms using metabolic pathways is still a difficult task. We present TabPath (Tables for Metabolic Pathway), a web-based tool to facilitate comparison of metabolic pathways in genomes based on KEGG. From a selection of pathways and genomes of interest on the menu, TabPath generates user-friendly tables that facilitate analysis of variations in metabolism among the selected organisms. TabPath is available at http://200.239.132.160:8686. lmmorei@gmail.com.

Effect of dewatering on seismic performance of multi-anchor wall due to high ground water level

NASA Astrophysics Data System (ADS)

Kobayashi, Makoto; Miura, Kinya; Konami, Takeharu; Hayashi, Taketo; Sato, Hiroki

2017-10-01

Previous research reported that the ground water in the backfill of reinforced soil wall made it deteriorate. According to the damage investigation of Great East Earthquake 2011, the reinforced soil structure due to high ground water level by seismic wave were deformed remarkably. Some of them classified ultimate limit state or restorability limit state. However, more than 90% of reinforced soil structure, which suffered from this earthquake, were classified into no damage condition. Therefore, it is necessary that the seismic behaviors of multi-anchor wall due to seepage flow should be clarified in order to adopt the performance-based design in such reinforced soil structure. In this study, a series of centrifugal shaking table tests were conducted to investigate the seismic behavior of multi-anchor wall due to high ground water level. The reinforced drainage pipes were installed into the backfill in order to verify the dewatering effect and additional reinforcement. Furthermore, to check only the dewatering effect, the model tests was carried out with several ground water table that was modeled the case reinforced drainage pipes installed. The test results show unique behavior of reinforced region that moved integrally. This implies that the reinforced region has been behaved as if it became one mass, and this behavior make this structure increase seismic performance. Thus, the effectiveness of dewatering was observed remarkably because of decreasing the inertial force during earthquake.

Correction to: Dapagliflozin decreases small dense low-density lipoprotein-cholesterol and increases high-density lipoprotein 2-cholesterol in patients with type 2 diabetes: comparison with sitagliptin.

PubMed

Hayashi, Toshiyuki; Fukui, Tomoyasu; Nakanishi, Noriko; Yamamoto, Saki; Tomoyasu, Masako; Osamura, Anna; Ohara, Makoto; Yamamoto, Takeshi; Ito, Yasuki; Hirano, Tsutomu

2017-11-13

Following publication of the original article [1], the authors identified a number of errors. In Result (P.3), Table 1 (P.4), Table 5 (P.9) and Supplementary Table 1, the correct unit for adiponectin was μg/mL. In Table 1 (P.4), the correct value for the post treatment body weight in dapagliflozin was 76.2±14.8. In Table 6 (P.10), the correct value for the pre treatment sd LDL/LDL-C in decreased LDL-C group was 0.38±0.10.

CyberShake Physics-Based PSHA in Central California

NASA Astrophysics Data System (ADS)

Callaghan, S.; Maechling, P. J.; Goulet, C. A.; Milner, K. R.; Graves, R. W.; Olsen, K. B.; Jordan, T. H.

2017-12-01

The Southern California Earthquake Center (SCEC) has developed a simulation platform, CyberShake, which performs physics-based probabilistic seismic hazard analyis (PSHA) using 3D deterministic wave propagation simulations. CyberShake performs PSHA by simulating a wavefield of Strain Green Tensors. An earthquake rupture forecast (ERF) is then extended by varying hypocenters and slips on finite faults, generating about 500,000 events per site of interest. Seismic reciprocity is used to calculate synthetic seismograms, which are processed to obtain intensity measures (IMs) such as RotD100. These are combined with ERF probabilities to produce hazard curves. PSHA results from hundreds of locations across a region are interpolated to produce a hazard map. CyberShake simulations with SCEC 3D Community Velocity Models have shown how the site and path effects vary with differences in upper crustal structure, and they are particularly informative about epistemic uncertainties in basin effects, which are not well parameterized by depths to iso-velocity surfaces, common inputs to GMPEs. In 2017, SCEC performed CyberShake Study 17.3, expanding into Central California for the first time. Seismic hazard calculations were performed at 1 Hz at 438 sites, using both a 3D tomographically-derived central California velocity model and a regionally averaged 1D model. Our simulation volumes extended outside of Central California, so we included other SCEC velocity models and developed a smoothing algorithm to minimize reflection and refraction effects along interfaces. CyberShake Study 17.3 ran for 31 days on NCSA's Blue Waters and ORNL's Titan supercomputers, burning 21.6 million core-hours and producing 285 million two-component seismograms and 43 billion IMs. These results demonstrate that CyberShake can be successfully expanded into new regions, and lend insights into the effects of directivity-basin coupling associated with basins near major faults such as the San Andreas. In particular, we observe in the 3D results that basin amplification for sites in the southern San Joaquin Valley is less than for sites in smaller basins such as around Ventura. We will present CyberShake hazard estimates from the 1D and 3D models, compare results to those from previous CyberShake studies and GMPEs, and describe our future plans.

Effectiveness of educational materials designed to change knowledge and behaviors regarding crying and shaken-baby syndrome in mothers of newborns: a randomized, controlled trial.

PubMed

Barr, Ronald G; Rivara, Frederick P; Barr, Marilyn; Cummings, Peter; Taylor, James; Lengua, Liliana J; Meredith-Benitz, Emily

2009-03-01

Infant crying is an important precipitant for shaken-infant syndrome. OBJECTIVE. To determine if parent education materials (The Period of PURPLE Crying [PURPLE]) change maternal knowledge and behavior relevant to infant shaking. This study was a randomized, controlled trial conducted in prenatal classes, maternity wards, and pediatric practices. There were 1374 mothers of newborns randomly assigned to the PURPLE intervention and 1364 mothers to the control group. Primary outcomes were measured by telephone 2 months after delivery. These included 2 knowledge scales about crying and the dangers of shaking; 3 scales about behavioral responses to crying generally and to unsoothable crying, and caregiver self-talk in response to unsoothable crying; and 3 questions concerning the behaviors of sharing of information with others about crying, walking away if frustrated, and the dangers of shaking. The mean infant crying knowledge score was greater in the intervention group (69.5) compared with controls (63.3). Mean shaking knowledge was greater for intervention subjects (84.8) compared with controls (83.5). For reported maternal behavioral responses to crying generally, responses to unsoothable crying, and for self-talk responses, mean scores for intervention mothers were similar to those for controls. For the behaviors of information sharing, more intervention mothers reported sharing information about walking away if frustrated and the dangers of shaking, but there was little difference in sharing information about infant crying. Intervention mothers also reported increased infant distress. Use of the PURPLE education materials seem to lead to higher scores in knowledge about early infant crying and the dangers of shaking, and in sharing of information behaviors considered to be important for the prevention of shaking.

Vortex shaking study of REBCO tape with consideration of anisotropic characteristics

NASA Astrophysics Data System (ADS)

Liang, Fei; Qu, Timing; Zhang, Zhenyu; Sheng, Jie; Yuan, Weijia; Iwasa, Yukikazu; Zhang, Min

2017-09-01

The second generation high temperature superconductor, specifically REBCO, has become a new research focus in the development of a new generation of high-field (>25 T) magnets. One of the main challenges in the application of the magnets is the current screening problem. Previous research shows that for magnetized superconducting stacks and bulks the application of an AC field in plane with the circulating current will lead to demagnetization due to vortex shaking, which provides a possible solution to remove the shielding current. This paper provides an in-depth study, both experimentally and numerically, to unveil the vortex shaking mechanism of REBCO stacks. A new experiment was carried out to measure the demagnetization rate of REBCO stacks exposed to an in-plane AC magnetic field. Meanwhile, 2D finite element models, based on the E-J power law, are developed for simulating the vortex shaking effect of the AC magnetic field. Qualitative agreement was obtained between the experimental and the simulation results. Our results show that the applied in-plane magnetic field leads to a sudden decay of trapped magnetic field in the first half shaking cycle, which is caused by the magnetic field dependence of critical current. Furthermore, the decline of demagnetization rate with the increase of tape number is mainly due to the cross-magnetic field being screened by the top and bottom stacks during the shaking process, which leads to lower demagnetization rate of inner layers. We also demonstrate that the frequency of the applied AC magnetic field has little impact on the demagnetization process. Our modeling tool and findings perfect the vortex shaking theory and provide helpful guidance for eliminating screening current in the new generation REBCO magnets.

Icilin-evoked behavioral stimulation is attenuated by alpha2-adrenoceptor activation

PubMed Central

Kim, Jae; Cowan, Alan; Lisek, Renata; Raymondi, Natalie; Rosenthal, Aaron; Hirsch, Daniel D.; Rawls, Scott M.

2011-01-01

Icilin is a transient receptor potential cation channel subfamily M (TRPM8) agonist that produces behavioral activation in rats and mice. Its hallmark overt pharmacological effect is wet-dog shakes (WDS) in rats. The vigorous shaking associated with icilin is dependent on NMDA receptor activation and nitric oxide production, but little else is known about the biological systems that modulate the behavioral phenomenon. The present study investigated the hypothesis that alpha2-adrenoceptor activation inhibits icilin-induced WDS. Rats injected with icilin (0.5, 1, 2.5, 5 mg/kg, i.p.) displayed dose-related WDS that were inhibited by pretreatment with a fixed dose of clonidine (0.15 mg/kg, s.c.). Shaking behavior caused by a fixed dose (2.5 mg/kg) of icilin was also inhibited in a dose-related manner by clonidine pretreatment (0.03–0.15 mg/kg, s.c.) and reduced by clonidine posttreatment (0.15 mg/kg, s.c.). Pretreatment with a peripherally restricted alpha2-adrenoceptor agonist, ST91 (0.075, 0.15 mg/kg), also decreased the incidence of shaking elicited by 2.5 mg/kg of icilin. Pretreatment with yohimbine (2 mg/kg, i.p.) enhanced the shaking induced by a low dose of icilin (0.5 mg/kg). The imidazoline site agonists, agmatine (150 mg/kg, i.p.) and 2-BFI (7 mg/kg, i.p.), did not affect icilin-evoked shaking. These results suggest that alpha2-adrenoceptor activation inhibits shaking induced by icilin and that increases in peripheral, as well as central, alpha2-adrenoceptor signaling oppose the behavioral stimulant effect of icilin. PMID:21315691

Experimental Analysis of Propeller Interactions With a Flexible Wing Micro-Air-Vehicle

DTIC Science & Technology

2006-03-23

Wing (Freestream Only) Momentum Balance Results.............. 94 Table 10. Flexible/ Rigid Wing (Freestream and Propeller Running) Momentum Balance ...107 Table 18. Propeller/MAV Forces and Moments at 14,000 RPM ( Rigid Wing) ............ 107 Table 19. Balance Data (Raw and Corrected...velocity field around the vehicle. A limited number of tests have been performed to assess the technique in comparison to force balance data. 4

Understanding earthquake hazards in urban areas - Evansville Area Earthquake Hazards Mapping Project

USGS Publications Warehouse

Boyd, Oliver S.

2012-01-01

The region surrounding Evansville, Indiana, has experienced minor damage from earthquakes several times in the past 200 years. Because of this history and the proximity of Evansville to the Wabash Valley and New Madrid seismic zones, there is concern among nearby communities about hazards from earthquakes. Earthquakes currently cannot be predicted, but scientists can estimate how strongly the ground is likely to shake as a result of an earthquake and are able to design structures to withstand this estimated ground shaking. Earthquake-hazard maps provide one way of conveying such information and can help the region of Evansville prepare for future earthquakes and reduce earthquake-caused loss of life and financial and structural loss. The Evansville Area Earthquake Hazards Mapping Project (EAEHMP) has produced three types of hazard maps for the Evansville area: (1) probabilistic seismic-hazard maps show the ground motion that is expected to be exceeded with a given probability within a given period of time; (2) scenario ground-shaking maps show the expected shaking from two specific scenario earthquakes; (3) liquefaction-potential maps show how likely the strong ground shaking from the scenario earthquakes is to produce liquefaction. These maps complement the U.S. Geological Survey's National Seismic Hazard Maps but are more detailed regionally and take into account surficial geology, soil thickness, and soil stiffness; these elements greatly affect ground shaking.

Forecasting probabilistic seismic shaking for greater Tokyo from 400 years of intensity observations

USGS Publications Warehouse

Bozkurt, S.B.; Stein, R.S.; Toda, S.

2007-01-01

The long recorded history of earthquakes in Japan affords an opportunity to forecast seismic shaking exclusively from past shaking. We calculate the time-averaged (Poisson) probability of severe shaking by using more than 10,000 intensity observations recorded since AD 1600 in a 350 km-wide box centered on Tokyo. Unlike other hazard-assessment methods, source and site effects are included without modeling, and we do not need to know the size or location of any earthquake nor the location and slip rate of any fault. The two key assumptions are that the slope of the observed frequency-intensity relation at every site is the same, and that the 400-year record is long enough to encompass the full range of seismic behavior. Tests we conduct here suggest that both assumptions are sound. The resulting 30-year probability of IJMA ??? 6 shaking (??? PGA ??? 0.4 g or MMI ??? IX) is 30%-40% in Tokyo, Kawasaki, and Yokohama, and 10% 15% in Chiba and Tsukuba. This result means that there is a 30% chance that 4 million people will be subjected to IJMA ??? 6 shaking during an average 30-year period. We also produce exceedance maps of PGA for building-code regulations, and calculate short-term hazard associated with a hypothetical catastrophe bond. Our results resemble an independent assessment developed from conventional seismic hazard analysis for greater Tokyo. ?? 2007, Earthquake Engineering Research Institute.

Drosophila Shaking-B protein forms gap junctions in paired Xenopus oocytes.

PubMed

Phelan, P; Stebbings, L A; Baines, R A; Bacon, J P; Davies, J A; Ford, C

1998-01-08

In most multicellular organisms direct cell-cell communication is mediated by the intercellular channels of gap junctions. These channels allow the exchange of ions and molecules that are believed to be essential for cell signalling during development and in some differentiated tissues. Proteins called connexins, which are products of a multigene family, are the structural components of vertebrate gap junctions. Surprisingly, molecular homologues of the connexins have not been described in any invertebrate. A separate gene family, which includes the Drosophila genes shaking-B and l(1)ogre, and the Caenorhabditis elegans genes unc-7 and eat-5, encodes transmembrane proteins with a predicted structure similar to that of the connexins. shaking-B and eat-5 are required for the formation of functional gap junctions. To test directly whether Shaking-B is a channel protein, we expressed it in paired Xenopus oocytes. Here we show that Shaking-B localizes to the membrane, and that its presence induces the formation of functional intercellular channels. To our knowledge, this is the first structural component of an invertebrate gap junction to be characterized.

Modeling of growth and laccase production by Pycnoporus sanguineus.

PubMed

Saat, Muhammad Naziz; Annuar, Mohamad Suffian Mohamad; Alias, Zazali; Chuan, Ling Tau; Chisti, Yusuf

2014-05-01

Production of extracellular laccase by the white-rot fungus Pycnoporus sanguineus was examined in batch submerged cultures in shake flasks, baffled shake flasks and a stirred tank bioreactor. The biomass growth in the various culture systems closely followed a logistic growth model. The production of laccase followed a Luedeking-Piret model. A modified Luedeking-Piret model incorporating logistic growth effectively described the consumption of glucose. Biomass productivity, enzyme productivity and substrate consumption were enhanced in baffled shake flasks relative to the cases for the conventional shake flasks. This was associated with improved oxygen transfer in the presence of the baffles. The best results were obtained in the stirred tank bioreactor. At 28 °C, pH 4.5, an agitation speed of 600 rpm and a dissolved oxygen concentration of ~25 % of air saturation, the laccase productivity in the bioreactor exceeded 19 U L(-1 )days(-1), or 1.5-fold better than the best case for the baffled shake flask. The final concentration of the enzyme was about 325 U L(-1).

Role of nuclear charge change and nuclear recoil on shaking processes and their possible implication on physical processes

NASA Astrophysics Data System (ADS)

Sharma, Prashant

2017-12-01

The probable role of the sudden nuclear charge change and nuclear recoil in the shaking processes during the neutron- or heavy-ion-induced nuclear reactions and weakly interacting massive particle-nucleus scattering has been investigated in the present work. Using hydrogenic wavefunctions, general analytical expressions of survival, shakeup/shakedown, and shakeoff probability have been derived for various subshells of hydrogen-like atomic systems. These expressions are employed to calculate the shaking, shakeup/shakedown, and shakeoff probabilities in some important cases of interest in the nuclear astrophysics and the dark matter search experiments. The results underline that the shaking processes are one of the probable channels of electronic transitions during the weakly interacting massive particle-nucleus scattering, which can be used to probe the dark matter in the sub-GeV regime. Further, it is found that the shaking processes initiating due to nuclear charge change and nuclear recoil during the nuclear reactions may influence the electronic configuration of the participating atomic systems and thus may affect the nuclear reaction measurements at astrophysically relevant energies.

Meal replacements as a weight loss tool in a population with severe mental illness.

PubMed

Gelberg, Hollie A; Kwan, Crystal L; Mena, Shirley J; Erickson, Zachary D; Baker, Matthew R; Chamberlin, Valery; Nguyen, Charles; Rosen, Jennifer A; Shah, Chandresh; Ames, Donna

2015-12-01

Weight gain and worsening metabolic parameters are often side effects of antipsychotic medications used by individuals with severe mental illness. To address this, a randomized, controlled research study of a behavioral weight management program for individuals with severe mental illness was undertaken to assess its efficacy. Patients unable to meet weight loss goals during the first portion of the year-long study were given the option of using meal replacement shakes in an effort to assist with weight loss. Specific requirements for use of meal replacement shakes were specified in the study protocol; only five patients were able to use the shakes in accordance with the protocol and lose weight while improving metabolic parameters. Case studies of two subjects are presented, illustrating the challenges and obstacles they faced, as well as their successes. Taking responsibility for their own weight loss, remaining motivated through the end of the study, and incorporating the meal replacement shakes into a daily routine were factors found in common with these patients. Use of meal replacements shakes with this population may be effective. Published by Elsevier Ltd.

Measurement of the electron shake-off in the β-decay of laser-trapped 6He atoms

NASA Astrophysics Data System (ADS)

Hong, Ran; Bagdasarova, Yelena; Garcia, Alejandro; Storm, Derek; Sternberg, Matthew; Swanson, Erik; Wauters, Frederik; Zumwalt, David; Bailey, Kevin; Leredde, Arnaud; Mueller, Peter; O'Connor, Thomas; Flechard, Xavier; Liennard, Etienne; Knecht, Andreas; Naviliat-Cuncic, Oscar

2016-03-01

Electron shake-off is an important process in many high precision nuclear β-decay measurements searching for physics beyond the standard model. 6He being one of the lightest β-decaying isotopes, has a simple atomic structure. Thus, it is well suited for testing calculations of shake-off effects. Shake-off probabilities from the 23S1 and 23P2 initial states of laser trapped 6He matter for the on-going beta-neutrino correlation study at the University of Washington. These probabilities are obtained by analyzing the time-of-flight distribution of the recoil ions detected in coincidence with the beta particles. A β-neutrino correlation independent analysis approach was developed. The measured upper limit of the double shake-off probability is 2 ×10-4 at 90% confidence level. This result is ~100 times lower than the most recent calculation by Schulhoff and Drake. This work is supported by DOE, Office of Nuclear Physics, under Contract Nos. DE-AC02-06CH11357 and DE-FG02-97ER41020.

MyShake: Initial Observations from a Global Smartphone Seismic Network

NASA Astrophysics Data System (ADS)

Kong, Q.; Allen, R. M.; Schreier, L.

2016-12-01

MyShake is a global smartphone seismic network that harnesses the power of crowdsourcing. It has two component: an android application running on the personal smartphones to detect earthquake-like motion, and a network detection algorithm to aggregate results from multiple smartphones to detect earthquakes. The MyShake application was released to the public on Feb 12th 2016. Within the first 5 months, there are more than 200 earthquakes recorded by the smartphones all over the world, including events in Chile, Argentina, Mexico, Morocco, Greece, Nepal, New Zealand, Taiwan, Japan, and across North America. In this presentation, we will show the waveforms we recorded from the smartphones for different earthquakes, and the evidences for using this data as a supplementary to the current earthquake early warning system. We will also show the performance of MyShake system during the some earthquakes in US. In short, MyShake smartphone seismic network can be a nice complementary system to the current traditional seismic network, at the same time, it can be a standalone system in places where few seismic stations were installed to reduce the earthquake hazards.

Finite-momentum Bose-Einstein condensates in shaken two-dimensional square optical lattices

DOE Office of Scientific and Technical Information (OSTI.GOV)

Di Liberto, M.; Scuola Superiore di Catania, Universita di Catania, Via Valdisavoia 9, I-95123 Catania; Tieleman, O.

2011-07-15

We consider ultracold bosons in a two-dimensional square optical lattice described by the Bose-Hubbard model. In addition, an external time-dependent sinusoidal force is applied to the system, which shakes the lattice along one of the diagonals. The effect of the shaking is to renormalize the nearest-neighbor-hopping coefficients, which can be arbitrarily reduced, can vanish, or can even change sign, depending on the shaking parameter. Therefore, it is necessary to account for higher-order-hopping terms, which are renormalized differently by the shaking, and to introduce anisotropy into the problem. We show that the competition between these different hopping terms leads to finite-momentummore » condensates with a momentum that may be tuned via the strength of the shaking. We calculate the boundaries between the Mott insulator and the different superfluid phases and present the time-of-flight images expected to be observed experimentally. Our results open up possibilities for the realization of bosonic analogs of the Fulde, Ferrel, Larkin, and Ovchinnikov phase describing inhomogeneous superconductivity.« less

Seismic hazards in Thailand: a compilation and updated probabilistic analysis

NASA Astrophysics Data System (ADS)

Pailoplee, Santi; Charusiri, Punya

2016-06-01

A probabilistic seismic hazard analysis (PSHA) for Thailand was performed and compared to those of previous works. This PSHA was based upon (1) the most up-to-date paleoseismological data (slip rates), (2) the seismic source zones, (3) the seismicity parameters ( a and b values), and (4) the strong ground-motion attenuation models suggested as being suitable models for Thailand. For the PSHA mapping, both the ground shaking and probability of exceedance (POE) were analyzed and mapped using various methods of presentation. In addition, site-specific PSHAs were demonstrated for ten major provinces within Thailand. For instance, a 2 and 10 % POE in the next 50 years of a 0.1-0.4 g and 0.1-0.2 g ground shaking, respectively, was found for western Thailand, defining this area as the most earthquake-prone region evaluated in Thailand. In a comparison between the ten selected specific provinces within Thailand, the Kanchanaburi and Tak provinces had comparatively high seismic hazards, and therefore, effective mitigation plans for these areas should be made. Although Bangkok was defined as being within a low seismic hazard in this PSHA, a further study of seismic wave amplification due to the soft soil beneath Bangkok is required.

Anomalous concentrations of seismically triggered rock falls in Pacoima Canyon: Are they caused by highly susceptible slopes or local amplification of seismic shaking?

USGS Publications Warehouse

Harp, Edwin L.; Jibson, Randall W.

2002-01-01

Anomalously high concentrations of rock falls were triggered in Pacoima Canyon (Los Angeles, California) during the 1994 Northridge earthquake. Similar concentrations were also documented from the 1971 San Fernando earthquake. Using an engineering rock-mass classification that evaluates the susceptibility of rock slopes to seismic failure based on the fracture properties of a rock mass (in terms of a numerical "Q-value" that describes rock quality), the rock slopes in Pacoima Canyon were compared with rock slopes in sorrounding areas where topography and lithology are similar, but rock-fall concentrations from the earthquakes were much lower. A statistical comparison of Q-values from five sites surrounding Pacoima Canyon indicates that seismic susceptibilities are similar to those within Pacoima Canyon; differences in the characteristics of rock slopes between these sites are not sufficient to account for the relatively high concentrations of rock falls within Pacoima Canyon as compared to low concentrations elsewhere. By eliminating susceptibility differences as a cause, the most likely explanations for the differences in rock-fall concentrations is anomalously high shaking levels in Pacoima Canyon, possibly resulting from topographic amplification within the canyon.

A randomized comparison between league tables and funnel plots to inform health care decision-making.

PubMed

Anell, Anders; Hagberg, Oskar; Liedberg, Fredrik; Ryden, Stefan

2016-12-01

Comparison of provider performance is commonly used to inform health care decision-making. Little attention has been paid to how data presentations influence decisions. This study analyzes differences in suggested actions by decision-makers informed by league tables or funnel plots. Decision-makers were invited to a survey and randomized to compare hospital performance using either league tables or funnel plots for four different measures within the area of cancer care. For each measure, decision-makers were asked to suggest actions towards 12-16 hospitals (no action, ask for more information, intervene) and provide feedback related to whether the information provided had been useful. Swedish health care. Two hundred and twenty-one decision-makers at administrative and clinical levels. Data presentations in the form of league tables or funnel plots. Number of actions suggested by participants. Proportion of appropriate actions. For all four measures, decision-makers tended to suggest more actions based on the information provided in league tables compared to funnel plots (44% vs. 21%, P < 0.001). Actions were on average more appropriate for funnel plots. However, when using funnel plots, decision-makers more often missed to react even when appropriate. The form of data presentation had an influence on decision-making. With league tables, decision-makers tended to suggest more actions compared to funnel plots. A difference in sensitivity and specificity conditioned by the form of presentation could also be identified, with different implications depending on the purpose of comparisons. Explanations and visualization aids are needed to support appropriate actions. © The Author 2016. Published by Oxford University Press in association with the International Society for Quality in Health Care. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com

Discrete element simulation of the Jiufengershan rock-and-soil avalanche triggered by the 1999 Chi-Chi earthquake, Taiwan

NASA Astrophysics Data System (ADS)

Chang, Kuo-Jen; Taboada, Alfredo

2009-09-01

We present Contact Dynamics discrete element simulations of the earthquake-triggered Jiufengershan avalanche, which mobilized a 60 m thick, 1.5 km long sedimentary layer, dipping ˜22°SE toward a valley. The dynamic behavior of the avalanche is simulated under different assumptions about rock behavior, water table height, and boundary shear strength. Additionally, seismic shaking is introduced using strong motion records from nearby stations. We assume that seismic shaking generates shearing and frictional heating along the surface of rupture, which, in turn, may induce dynamic weakening and avalanche triggering; a simple "slip-weakening" criterion was adopted to simulate shear strength drop along the rupture surface. We investigate the mechanical processes occurring during triggering and propagation of an avalanche mobilizing shallowly dipping layers. Incipient deformation forms a pop-up structure at the toe of the dip slope. As the avalanche propagates, the pop-up deforms into an overturned fold, which overrides the surface of separation along a décollement. Simultaneously, uphill layers slide at high velocity (125 km/h) and are folded and disrupted as they reach the toe of the dip slope. The avalanche foot forms a wedge that is pushed forward as deformed rocks accrete at its rear. We simulated five cross sections across the Jiufengershan avalanche, which differ in the geometry of the surface of separation. Topographic and simulated surface profiles are similar. The friction coefficient at the surface of separation determined from back analysis is abnormally low (μSS = 0.2), possibly due to lubrication by liquefied soils. The granular deposits of simulated earthquake- and rain-triggered avalanches are similar.

The Mw6.0 24 August 2014 South Napa earthquake

USGS Publications Warehouse

Brocher, Thomas M.; Baltay, Annemarie S.; Hardebeck, Jeanne L.; Pollitz, Fred F.; Murray, Jessica R.; Llenos, Andrea L.; Schwartz, David P.; Blair, James Luke; Ponti, Daniel J.; Lienkaemper, James J.; Langenheim, V.E.; Dawson, Timothy E.; Hudnut, Kenneth W.; Shelly, David R.; Dreger, Douglas S.; Boatwright, John; Aagaard, Brad T.; Wald, David J.; Allen, Richard M.; Barnhart, William D.; Knudsen, Keith L.; Brooks, Benjamin A.; Scharer, Katherine M.

2015-01-01

The Mw 6.0 South Napa earthquake, which occurred at 10:20 UTC 24 August 2014 was the largest earthquake to strike the greater San Francisco Bay area since the Mw 6.9 1989 Loma Prieta earthquake. The rupture from this right‐lateral earthquake propagated mostly unilaterally to the north and up‐dip, directing the strongest shaking toward the city of Napa, where peak ground accelerations (PGAs) between 45%g and 61%g were recorded and modified Mercalli intensities (MMIs) of VII–VIII were reported. Tectonic surface rupture with dextral slip of up to 46 cm was observed on a 12.5 km long segment, some of which was along a previously mapped strand of the West Napa fault system, although the rupture extended to the north of the mapped Quaternary strand. Modeling of seismic and geodetic data suggests an average coseismic slip of 50 cm, with a maximum slip of about 1 m at depths of 10–11 km. We observed up to 35 cm of afterslip along the surface trace in the week following the mainshock, primarily along the southern half of the surface rupture that experienced relatively little coseismic offset. Relocation of the sparse aftershock sequence suggests en echelon southwest‐ and northeast‐dipping fault planes, reflective of the complex fault geometry in this region. The Napa basin and historic and late Holocene alluvial flood deposits in downtown Napa amplified the ground motions there. Few ground failures were mapped, reflecting the dry season (as well as a persistent drought that had lowered the groundwater table) and the short duration of strong shaking in the epicentral area.

TriNet "ShakeMaps": Rapid generation of peak ground motion and intensity maps for earthquakes in southern California

USGS Publications Warehouse

Wald, D.J.; Quitoriano, V.; Heaton, T.H.; Kanamori, H.; Scrivner, C.W.; Worden, C.B.

1999-01-01

Rapid (3-5 minutes) generation of maps of instrumental ground-motion and shaking intensity is accomplished through advances in real-time seismographic data acquisition combined with newly developed relationships between recorded ground-motion parameters and expected shaking intensity values. Estimation of shaking over the entire regional extent of southern California is obtained by the spatial interpolation of the measured ground motions with geologically based frequency and amplitude-dependent site corrections. Production of the maps is automatic, triggered by any significant earthquake in southern California. Maps are now made available within several minutes of the earthquake for public and scientific consumption via the World Wide Web; they will be made available with dedicated communications for emergency response agencies and critical users.

Optoelectronic switch matrix as a look-up table for residue arithmetic.

PubMed

Macdonald, R I

1987-10-01

The use of optoelectronic matrix switches to perform look-up table functions in residue arithmetic processors is proposed. In this application, switchable detector arrays give the advantage of a greatly reduced requirement for optical sources by comparison with previous optoelectronic residue processors.

Relative performance of several inexpensive accelerometers

USGS Publications Warehouse

Evans, John R.; Rogers, John A.

1995-01-01

We examined the performance of several low-cost accelerometers for highly cost-driven applications in recording earthquake strong motion. We anticipate applications for such sensors in providing the lifeline and emergency-response communities with an immediate, comprehensive picture of the extent and characteristics of likely damage. We also foresee their use as 'filler' instruments sited between research-grade instruments to provide spatially detailed and near-field records of large earthquakes (on the order of 1000 stations at 600-m intervals in San Fernando Valley, population 1.2 million, for example). The latter applications would provide greatly improved attenuation relationships for building codes and design, the first examples of mainshock information (that is, potentially nonlinear regime) for microzonation, and a suite of records for structural engineers. We also foresee possible applications in monitoring structural inter-story drift during earthquakes, possibly leading to local and remote alarm functions as well as design criteria. This effort appears to be the first of its type at the USGS. It is spurred by rapid advances in sensor technology and the recognition of potential non-classical applications. In this report, we estimate sensor noise spectra, relative transfer functions and cross-axis sensitivity of six inexpensive sensors. We tested three micromachined ('silicon-chip') sensors in addition to classical force-balance and piezoelectric examples. This sample of devices is meant to be representative, not comprehensive. Sensor noise spectra were estimated by recording system output with the sensor mounted on a pneumatically supported 545-kg optical-bench isolation table. This isolation table appears to limit ground motion to below our system noise level. These noise estimates include noise introduced by signal-conditioning circuitry, the analog-to-digital converter (ADC), and noise induced in connecting wiring by ambient electromagnetic fields in our suburban laboratory. These latter sources are believed to dominate sensor noise in the quieter sensors we tested. Transfer functions were obtained relative to a research grade force-balance accelerometer (a Kinemetrics TM FBA-11) by shaking the sensors simultaneously on the same shake table and taking spectral ratios with the output of the FBA- 11. This reference sensor is said to have 120 db dynamic range (-+20 bits, though we only digitized it at 16 bits resolution and drove it with relatively small signals). We did not test temperature sensitivity, which is thought to be a significant issue at least for the silicon devices. Though these tests were not designed to be definitive (our anticipated applications do not demand research-grade precision), our tests do appear to have been successful in estimating relative transfer functions from about 0.3 to 50 Hz. Most sensors performed adequately in this range, with essentially fiat relative transfer functions. Noise tests appear to measure sensor noise well for the noisier (generally less expensive) instruments from about 0.1 to 50 Hz.

Temporal changes in the configuration of the water table in the vicinity of the management systems evaluation area site, central Nebraska

USGS Publications Warehouse

Kilpatrick, John M.

1996-01-01

To improve understanding of the hydrologic characteristics of the shallow aquifer in the vicinity of the Management Systems Evaluation Area site near Shelton, Nebraska, water levels were measured in approximately 130 observation wells in both June and September 1991. Two water-table maps and a water-level-change map were drawn on the basis of these measurements. In addition, historical data from U.S. Geological Survey computer files and published reports were used to determine the approximate configuration of the water table in 1931 and to draw one short-term and two-long term water- level hydrographs. Comparison of the three water- table maps indicates general similarities. The average horizontal hydraulic gradient in the shallow aquifer is about 7.5 feet per mile, and the flow direction is to the east-northeast. The water table declined 2 to 10 feet between June and September 1991, with the greatest decline occurring in a wedge-shaped area south of the Wood River and north of the Platte River. The 1991 water-table configurations appear to indicate that the aquifer either was discharging to the Platte River in this reach or there was little flow between the river and the aquifer. Comparison of the 1931 and 1991 water-table maps indicates that, except for short-term variations, the water-table configuration changed little during this 61-year period. Two long-term water-level hydrographs confirm this conclusion, indicating that the shallow aquifer in this area has been in long-term, dynamic equilibrium.

Antifoam addition to shake flask cultures of recombinant Pichia pastoris increases yield

PubMed Central

2011-01-01

Background Pichia pastoris is a widely-used host for recombinant protein production. Initial screening for both suitable clones and optimum culture conditions is typically carried out in multi-well plates. This is followed by up-scaling either to shake-flasks or continuously stirred tank bioreactors. A particular problem in these formats is foaming, which is commonly prevented by the addition of chemical antifoaming agents. Intriguingly, antifoams are often added without prior consideration of their effect on the yeast cells, the protein product or the influence on downstream processes such as protein purification. In this study we characterised, for the first time, the effects of five commonly-used antifoaming agents on the total amount of recombinant green fluorescent protein (GFP) secreted from shake-flask cultures of this industrially-relevant yeast. Results Addition of defined concentrations of Antifoam A (Sigma), Antifoam C (Sigma), J673A (Struktol), P2000 (Fluka) or SB2121 (Struktol) to shake-flask cultures of P. pastoris increased the total amount of recombinant GFP in the culture medium (the total yield) and in the case of P2000, SB2121 and J673A almost doubled it. When normalized to the culture density, the GFP specific yield (μg OD595-1) was only increased for Antifoam A, Antifoam C and J673A. Whilst none of the antifoams affected the growth rate of the cells, addition of P2000 or SB2121 was found to increase culture density. There was no correlation between total yield, specific yield or specific growth rate and the volumetric oxygen mass transfer coefficient (kLa) in the presence of antifoam. Moreover, the antifoams did not affect the dissolved oxygen concentration of the cultures. A comparison of the amount of GFP retained in the cell by flow cytometry with that in the culture medium by fluorimetry suggested that addition of Antifoam A, Antifoam C or J673A increased the specific yield of GFP by increasing the proportion secreted into the medium. Conclusions We show that addition of a range of antifoaming agents to shake flask cultures of P. pastoris increases the total yield of the recombinant protein being produced. This is not only a simple method to increase the amount of protein in the culture, but our study also provides insight into how antifoams interact with microbial cell factories. Two mechanisms are apparent: one group of antifoams (Antifoam A, Antifoam C and J673A) increases the specific yield of GFP by increasing the total amount of protein produced and secreted per cell, whilst the second (P2000 or SB2121) increases the total yield by increasing the density of the culture. PMID:21426555

Facile mechanical shaking method is an improved isolation approach for islet preparation and transplantation.

PubMed

Yin, Nina; Chen, Tao; Yu, Yuling; Han, Yongming; Yan, Fei; Zheng, Zhou; Chen, Zebin

2016-12-01

Successful islet isolation is crucial for islet transplantation and cell treatment for type 1 diabetes. Current isolation methods are able to obtain 500-1,000 islets per rat, which results in a waste of ≥50% of total islets. In the present study, a facile mechanical shaking method for improving islet yield (up to 1,500 per rat) was developed and summarized, which was demonstrated to be more effective than the existing well-established stationary method. The present results showed that isolated islets have a maximum yield of 1,326±152 when shaking for 15 min for the fully-cannulated pancreas. For both fully-cannulated and half-cannulated pancreas in the presence of rat DNAse inhibitor, the optimal shaking time was amended to 20 min with a further increased yield of 1,344±134 and 1,286±124 islets, respectively. Furthermore, the majority of the isolated islets were morphologically intact with a well-defined surface and almost no central necrotic zone, which suggested that the condition of islets obtained via the mechanical shaking method was consistent with the stationary method. Islet size distribution was also calculated and it was demonstrated that islets from the stationary method exhibited the same size distribution as the non-cannulated group, which had more larger islets than the fully-cannulated and half-cannulated groups isolated via the shaking method. In addition, the results of glucose challenge showed that the refraction index of each group was >2.5, which indicated the well-preserved function of isolated islets. Furthermore, the transplanted islets exhibited a therapeutic effect after 1 day of transplantation; however, they failed to control blood glucose levels after ~7 days of transplantation. In conclusion, these results demonstrated that the facile mechanical shaking method may markedly improve the yield of rat islet isolation, and in vitro and in vivo investigation demonstrated the well-preserved function of isolated islets in the control of blood glucose. Therefore, the facile mechanical shaking method may be an alternative improved procedure to obtain higher islet yield for islet preparation and transplantation in the treatment of type 1 diabetes.

How well should probabilistic seismic hazard maps work?

NASA Astrophysics Data System (ADS)

Vanneste, K.; Stein, S.; Camelbeeck, T.; Vleminckx, B.

2016-12-01

Recent large earthquakes that gave rise to shaking much stronger than shown in earthquake hazard maps have stimulated discussion about how well these maps forecast future shaking. These discussions have brought home the fact that although the maps are designed to achieve certain goals, we know little about how well they actually perform. As for any other forecast, this question involves verification and validation. Verification involves assessing how well the algorithm used to produce hazard maps implements the conceptual PSHA model ("have we built the model right?"). Validation asks how well the model forecasts the shaking that actually occurs ("have we built the right model?"). We explore the verification issue by simulating the shaking history of an area with assumed distribution of earthquakes, frequency-magnitude relation, temporal occurrence model, and ground-motion prediction equation. We compare the "observed" shaking at many sites over time to that predicted by a hazard map generated for the same set of parameters. PSHA predicts that the fraction of sites at which shaking will exceed that mapped is p = 1 - exp(t/T), where t is the duration of observations and T is the map's return period. This implies that shaking in large earthquakes is typically greater than shown on hazard maps, as has occurred in a number of cases. A large number of simulated earthquake histories yield distributions of shaking consistent with this forecast, with a scatter about this value that decreases as t/T increases. The median results are somewhat lower than predicted for small values of t/T and approach the predicted value for larger values of t/T. Hence, the algorithm appears to be internally consistent and can be regarded as verified for this set of simulations. Validation is more complicated because a real observed earthquake history can yield a fractional exceedance significantly higher or lower than that predicted while still being consistent with the hazard map in question. As a result, given that in the real world we have only a single sample, it is hard to assess whether a misfit between a map and observations arises by chance or reflects a biased map.

Applicability of the Moyers' Probability Tables in Adolescents with Different Facial Biotypes

PubMed Central

Carrillo, Jorge J. Pavani; Rubial, Maria C.; Albornoz, Cristina; Villalba, Silvina; Damiani, Patricia; de Cravero, Marta Rugani

2017-01-01

Introduction: The Moyers’ probability tables are used in mixed dentition analysis to estimate the extent of space required for the alignment of canines and premolars, by correlating the mesiodistal size of lower incisors with the size of permanent canines and premolars. Objective: This study intended to evaluate the applicability of the Moyer's probability tables for predicting the mesiodistal space needed for the correct location of premolars and permanent canines non-erupted, in adolescents of the city of Cordoba, Argentina, who show different facial biotypes. Materials and Methods: Models and tele-radiographies of 478 adolescents of both genders from 10 to 15 years of age were analyzed. The tele-radiographies were measured manually in order to determine the facial biotype. The models were scanned with a gauged scanner (HP 3670) and measured by using Image Pro Plus 4.5 software. Results: According to this study, the comparison between the Moyer´s probability table, and the table created at the National University of Córdoba (UNC) (at 95%, 75%, and 50%) shows that, in both tables, a higher value of mesiodistal width of lower incisors corresponds to a bigger difference in the space needed for permanent canines and premolars; being the need for space for permanents canines and premolars bigger in the UNC´s table. On the other hand, when contrasting the values of mesiodistal space for permanent canines and premolars associated with each facial biotype, the discrepancies between groups were not statistically significant (P >0.05). However, we found differences in the size of the space required according to the mesiodistal width range of the lower incisors for each biotype: a) The comparison of lower-range values, with a mesialdistal width of lower incisors less than 22 mm, the space required for permanent canines and premolars resulted smaller in patients with dolichofacial biotype than in patients with mesofacial and braquifacial biotypes. The latter biotypes have meager differences between them. b) The comparison of mid-range values, with a mesialdistal width of lower incisors from 22 to 25 millimeters, shows that the values of required alignment space are similar in the three facial biotypes. c) Finally, the comparison of upper range values, with a mesialdistal width of lower incisors greater than 25 millimeters, indicates that the space required for dolichofacial biotypes tends to be higher than in mesofacial and brachyfacial biotypes. Conclusion: The Moyer´s probability tables should be created to meet the needs of the population under study, with no consideration of patients’ facial biotypes. PMID:28567145

Scenario earthquake hazards for the Long Valley Caldera-Mono Lake area, east-central California (ver. 2.0, January 2018)

USGS Publications Warehouse

Chen, Rui; Branum, David M.; Wills, Chris J.; Hill, David P.

2014-06-30

As part of the U.S. Geological Survey’s (USGS) multi-hazards project in the Long Valley Caldera-Mono Lake area, the California Geological Survey (CGS) developed several earthquake scenarios and evaluated potential seismic hazards, including ground shaking, surface fault rupture, liquefaction, and landslide hazards associated with these earthquake scenarios. The results of these analyses can be useful in estimating the extent of potential damage and economic losses because of potential earthquakes and also for preparing emergency response plans.The Long Valley Caldera-Mono Lake area has numerous active faults. Five of these faults or fault zones are considered capable of producing magnitude ≥6.7 earthquakes according to the Uniform California Earthquake Rupture Forecast, Version 2 (UCERF 2) developed by the 2007 Working Group on California Earthquake Probabilities (WGCEP) and the USGS National Seismic Hazard Mapping Program. These five faults are the Fish Slough, Hartley Springs, Hilton Creek, Mono Lake, and Round Valley Faults. CGS developed earthquake scenarios for these five faults in the study area and for the White Mountains Fault Zone to the east of the study area.In this report, an earthquake scenario is intended to depict the potential consequences of significant earthquakes. A scenario earthquake is not necessarily the largest or most damaging earthquake possible on a recognized fault. Rather it is both large enough and likely enough that emergency planners should consider it in regional emergency response plans. In particular, the ground motion predicted for a given scenario earthquake does not represent a full probabilistic hazard assessment, and thus it does not provide the basis for hazard zoning and earthquake-resistant building design.Earthquake scenarios presented here are based on fault geometry and activity data developed by the WGCEP, and are consistent with the 2008 Update of the United States National Seismic Hazard Maps (NSHM). Alternatives to the NSHM scenario were developed for the Hilton Creek and Hartley Springs Faults to account for different opinions in how far these two faults extend into Long Valley Caldera. For each scenario, ground motions were calculated using the current standard practice: the deterministic seismic hazard analysis program developed by Art Frankel of USGS and three Next Generation Ground Motion Attenuation (NGA) models. Ground motion calculations incorporated the potential amplification of seismic shaking by near-surface soils defined by a map of the average shear wave velocity in the uppermost 30 m (VS30) developed by CGS.In addition to ground shaking and shaking-related ground failure such as liquefaction and earthquake induced landslides, earthquakes cause surface rupture displacement, which can lead to severe damage of buildings and lifelines. For each earthquake scenario, potential surface fault displacements are estimated using deterministic and probabilistic approaches. Liquefaction occurs when saturated sediments lose their strength because of ground shaking. Zones of potential liquefaction are mapped by incorporating areas where loose sandy sediments, shallow groundwater, and strong earthquake shaking coincide in the earthquake scenario. The process for defining zones of potential landslide and rockfall incorporates rock strength, surface slope, and existing landslides, with ground motions caused by the scenario earthquake.Each scenario is illustrated with maps of seismic shaking potential and fault displacement, liquefaction, and landslide potential. Seismic shaking is depicted by the distribution of shaking intensity, peak ground acceleration, and 1.0-second spectral acceleration. One-second spectral acceleration correlates well with structural damage to surface facilities. Acceleration greater than 0.2 g is often associated with strong ground shaking and may cause moderate to heavy damage. The extent of strong shaking is influenced by subsurface fault dip and near surface materials. Strong shaking is more widespread in the hanging wall regions of a normal fault. Larger ground motions also occur where young alluvial sediments amplify the shaking. Both of these effects can lead to strong shaking that extends farther from the fault on the valley side than on the hill side.The effect of fault rupture displacements may be localized along the surface trace of the mapped earthquake fault if fault geometry is simple and the fault traces are accurately located. However, surface displacement hazards can spread over a few hundred meters to a few kilometers if the earthquake fault has numerous splays or branches, such as the Hilton Creek Fault. Faulting displacements are estimated to be about 1 meter along normal faults in the study area and close to 2 meters along the White Mountains Fault Zone.All scenarios show the possibility of widespread ground failure. Liquefaction damage would likely occur in the areas of higher ground shaking near the faults where there are sandy/silty sediments and the depth to groundwater is 6.1 meters (20 feet) or less. Generally, this means damage is most common near lakes and streams in the areas of strongest shaking. Landslide potential exists throughout the study region. All steep slopes (>30 degrees) present a potential hazard at any level of shaking. Lesser slopes may have landslides within the areas of the higher ground shaking. The landslide hazard zones also are likely sources for snow avalanches during winter months and for large boulders that can be shaken loose and roll hundreds of feet down hill, which happened during the 1980 Mammoth Lakes earthquakes.Whereas methodologies used in estimating ground shaking, liquefaction, and landslides are well developed and have been applied in published hazard maps; methodologies used in estimating surface fault displacement are still being developed. Therefore, this report provides a more in-depth and detailed discussion of methodologies used for deterministic and probabilistic fault displacement hazard analyses for this project.

Evaluation of knowledge regarding Shaken Baby Syndrome among parents and medical staff.

PubMed

Marcinkowska, Urszula; Tyrala, Kinga; Paniczek, Monika; Ledwon, Martyna; Josko-Ochojska, Jadwiga

2016-06-08

Shaken Baby Syndrome (SBS), currently functioning as Abusive Head Trauma (AHT), is a form of violence against children mainly under 2 years of age. The number of SBS might be underestimated, as many cases of violence remain unreported. The aim of the study was evaluation of the state of knowledge of the SBS phenomenon, its scale and diagnostic methods among parents, medical staff and medical students. 639 people were examined: 39% of parents, 32,5% medical staff members and 28,5% of medical students. 82% were women. The average age was 34,9 years (SD=9,78). 70% of them had children. The research tool was an anonymous survey. The 34 questions concerned numerous aspects of violence against children as well as knowledge about SBS. According to 90% of the interviewees shaking a baby may be dangerous but 43% have ever heard about shaken baby syndrome. 'SBS is a form of violence' said 88% of respondents but 57% realize that one-time shaking can lead to death and only 19% indicated men as aggressors. 16% of medical staff members did not know how long it takes for the consequences of shaking a baby to be revealed. Majority of the medical staff members working with children have never heard about SBS. Only half of the surveyed understands the connection of shaking with vision loss or child's death. Among the long-term consequences of shaking a baby the greatest knowledge concerns emotional consequences of shaking.

The Great California ShakeOut: Science-Based Preparedness Advocacy

NASA Astrophysics Data System (ADS)

Benthien, M. L.

2009-12-01

The Great Southern California ShakeOut in November 2008 was the largest earthquake drill in U.S. history, involving over 5 million southern Californians through a broad-based outreach program, media partnerships, and public advocacy by hundreds of partners. The basis of the drill was a comprehensive scenario for a magnitude 7.8 earthquake on the southern San Andreas fault, which would cause broad devastation. In early 2009 the decision was made to hold the drill statewide on the third Thursday of October each year (October 15 in 2009). Results of the 2008 and 2009 drills will be shared in this session. In addition, prospects of early warning systems will be described, that will one day provide the needed seconds before strong shaking arrives in which critical systems and be shut down, and people can do what they've been practicing in the ShakeOut drills: drop, cover, and hold on. A key aspect of the ShakeOut is the integration of a comprehensive earthquake scenario (incorporating earth science, engineering, policy, economics, public health, and other disciplines) and the lessons learned from decades of social science research about why people get prepared. The result is a “teachable moment” on par with having an actual earthquake (often followed by increased interest in getting ready for earthquakes). ShakeOut creates the sense of urgency that is needed for people, organizations, and communities to get prepared, to practice what to do to be safe, and to learn what plans need to be improved.

MyShake: Smartphone-based detection and analysis of Oklahoma earthquakes

NASA Astrophysics Data System (ADS)

Kong, Q.; Allen, R. M.; Schreier, L.

2016-12-01

MyShake is a global smartphone seismic network that harnesses the power of crowdsourcing (myshake.berkeley.edu). It uses the accelerometer data from phones to detect earthquake-like motion, and then uploads triggers and waveform data to a server for aggregation of the results. Since the public release in Feb 2016, more than 200,000 android-phone owners have installed the app, and the global network has recorded more than 300 earthquakes. In Oklahoma, there are about 200 active users each day providing enough data for the network to detect earthquakes and for us to perform analysis of the events. MyShake has recorded waveform data for M2.6 to M5.8 earthquakes in the state. For the September 3, 2016, M5.8 earthquake 14 phones detected the event and we can use the waveforms to determine event characteristics. MyShake data provides a location 3.95 km from the ANSS location and a magnitude of 5.7. We can also use MyShake data to estimate a stress drop of 7.4 MPa. MyShake is still a rapidly expanding network that has the ability to grow by thousands of stations/phones in a matter of hours as public interest increases. These initial results suggest that the data will be useful for a variety of scientific studies of induced seismicity phenomena in Oklahoma as well as having the potential to provide earthquake early warning in the future.

Seismomorphogenesis: a novel approach to acclimatization of tissue culture regenerated plants.

PubMed

Sarmast, Mostafa Khoshhal; Salehi, Hassan; Khosh-Khui, Morteza

2014-12-01

Plantlets under in vitro conditions transferred to ex vivo conditions are exposed to biotic and abiotic stresses. Furthermore, in vitro regenerated plants are typically frail and sometimes difficult to handle subsequently increasing their risk to damage and disease; hence acclimatization of these plantlets is the most important step in tissue culture techniques. An experiment was conducted under in vitro conditions to study the effects of shaking duration (twice daily at 6:00 a.m. and 9:00 p.m. for 2, 4, 8, and 16 min at 250 rpm for 14 days) on Sansevieria trifasciata L. as a model plant. Results showed that shaking improved handling, total plant height, and leaf characteristics of the model plant. Forty-eight hours after 14 days of shaking treatments with increasing shaking time, leaf length decreased but proline content of leaf increased. However, 6 months after starting the experiment different results were observed. In explants that received 16 min of shaking treatment, leaf length and area and photosynthesis rate were increased compared with control plantlets. Six months after starting the experiment, control plantlets had 12.5 % mortality; however, no mortality was observed in other treated explants. The results demonstrated that shaking improved the explants' root length and number and as a simple, cost-effective, and non-chemical novel approach may be substituted for other prevalent acclimatization techniques used for tissue culture regenerated plantlets. Further studies with sensitive plants are needed to establish this hypothesis.

Induced earthquake during the 2016 Kumamoto earthquake (Mw7.0): Importance of real-time shake monitoring for Earthquake Early Warning

NASA Astrophysics Data System (ADS)

Hoshiba, M.; Ogiso, M.

2016-12-01

Sequence of the 2016 Kumamoto earthquakes (Mw6.2 on April 14, Mw7.0 on April 16, and many aftershocks) caused a devastating damage at Kumamoto and Oita prefectures, Japan. During the Mw7.0 event, just after the direct S waves passing the central Oita, another M6 class event occurred there more than 80 km apart from the Mw7.0 event. The M6 event is interpreted as an induced earthquake; but it brought stronger shaking at the central Oita than that from the Mw7.0 event. We will discuss the induced earthquake from viewpoint of Earthquake Early Warning. In terms of ground shaking such as PGA and PGV, the Mw7.0 event is much smaller than those of the M6 induced earthquake at the central Oita (for example, 1/8 smaller at OIT009 station for PGA), and then it is easy to discriminate two events. However, PGD of the Mw7.0 is larger than that of the induced earthquake, and its appearance is just before the occurrence of the induced earthquake. It is quite difficult to recognize the induced earthquake from displacement waveforms only, because the displacement is strongly contaminated by that of the preceding Mw7.0 event. In many methods of EEW (including current JMA EEW system), magnitude is used for prediction of ground shaking through Ground Motion Prediction Equation (GMPE) and the magnitude is often estimated from displacement. However, displacement magnitude does not necessarily mean the best one for prediction of ground shaking, such as PGA and PGV. In case of the induced earthquake during the Kumamoto earthquake, displacement magnitude could not be estimated because of the strong contamination. Actually JMA EEW system could not recognize the induced earthquake. One of the important lessons we learned from eight years' operation of EEW is an issue of the multiple simultaneous earthquakes, such as aftershocks of the 2011 Mw9.0 Tohoku earthquake. Based on this lesson, we have proposed enhancement of real-time monitor of ground shaking itself instead of rapid estimation of hypocenter location and magnitude. Because we want to predict ground shaking in EEW, we should more focus on monitoring of ground shaking. Experience of the induced earthquake also indicates the importance of the real-time monitor of ground shaking for making EEW more rapid and precise.

SCEC Earthquake System Science Using High Performance Computing

NASA Astrophysics Data System (ADS)

Maechling, P. J.; Jordan, T. H.; Archuleta, R.; Beroza, G.; Bielak, J.; Chen, P.; Cui, Y.; Day, S.; Deelman, E.; Graves, R. W.; Minster, J. B.; Olsen, K. B.

2008-12-01

The SCEC Community Modeling Environment (SCEC/CME) collaboration performs basic scientific research using high performance computing with the goal of developing a predictive understanding of earthquake processes and seismic hazards in California. SCEC/CME research areas including dynamic rupture modeling, wave propagation modeling, probabilistic seismic hazard analysis (PSHA), and full 3D tomography. SCEC/CME computational capabilities are organized around the development and application of robust, re- usable, well-validated simulation systems we call computational platforms. The SCEC earthquake system science research program includes a wide range of numerical modeling efforts and we continue to extend our numerical modeling codes to include more realistic physics and to run at higher and higher resolution. During this year, the SCEC/USGS OpenSHA PSHA computational platform was used to calculate PSHA hazard curves and hazard maps using the new UCERF2.0 ERF and new 2008 attenuation relationships. Three SCEC/CME modeling groups ran 1Hz ShakeOut simulations using different codes and computer systems and carefully compared the results. The DynaShake Platform was used to calculate several dynamic rupture-based source descriptions equivalent in magnitude and final surface slip to the ShakeOut 1.2 kinematic source description. A SCEC/CME modeler produced 10Hz synthetic seismograms for the ShakeOut 1.2 scenario rupture by combining 1Hz deterministic simulation results with 10Hz stochastic seismograms. SCEC/CME modelers ran an ensemble of seven ShakeOut-D simulations to investigate the variability of ground motions produced by dynamic rupture-based source descriptions. The CyberShake Platform was used to calculate more than 15 new probabilistic seismic hazard analysis (PSHA) hazard curves using full 3D waveform modeling and the new UCERF2.0 ERF. The SCEC/CME group has also produced significant computer science results this year. Large-scale SCEC/CME high performance codes were run on NSF TeraGrid sites including simulations that use the full PSC Big Ben supercomputer (4096 cores) and simulations that ran on more than 10K cores at TACC Ranger. The SCEC/CME group used scientific workflow tools and grid-computing to run more than 1.5 million jobs at NCSA for the CyberShake project. Visualizations produced by a SCEC/CME researcher of the 10Hz ShakeOut 1.2 scenario simulation data were used by USGS in ShakeOut publications and public outreach efforts. OpenSHA was ported onto an NSF supercomputer and was used to produce very high resolution hazard PSHA maps that contained more than 1.6 million hazard curves.

Correlation of AH-1G airframe test data with a NASTRAN mathematical model

NASA Technical Reports Server (NTRS)

Cronkhite, J. D.; Berry, V. L.

1976-01-01

Test data was provided for evaluating a mathematical vibration model of the Bell AH-1G helicopter airframe. The math model was developed and analyzed using the NASTRAN structural analysis computer program. Data from static and dynamic tests were used for comparison with the math model. Static tests of the fuselage and tailboom were conducted to verify the stiffness representation of the NASTRAN model. Dynamic test data were obtained from shake tests of the airframe and were used to evaluate the NASTRAN model for representing the low frequency (below 30 Hz) vibration response of the airframe.

Communication during copulation in the sex-role reversed wolf spider Allocosa brasiliensis: Female shakes for soliciting new ejaculations?

PubMed

Garcia Diaz, Virginia; Aisenberg, Anita; Peretti, Alfredo V

2015-07-01

Traditional studies on sexual communication have focused on the exchange of signals during courtship. However, communication between the sexes can also occur during or after copulation. Allocosa brasiliensis is a wolf spider that shows a reversal in typical sex roles and of the usual sexual size dimorphism expected for spiders. Females are smaller than males and they are the roving sex that initiates courtship. Occasional previous observations suggested that females performed body shaking behaviors during copulation. Our objective was to analyze if female body shaking is associated with male copulatory behavior in A. brasiliensis, and determine if this female behavior has a communicatory function in this species. For that purpose, we performed fine-scaled analysis of fifteen copulations under laboratory conditions. We video-recorded all the trials and looked for associations between female and male copulatory behaviors. The significant difference between the time before and after female shaking, in favor of the subsequent ejaculation is analyzed. We discuss if shaking could be acting as a signal to accelerate and motivate palpal insertion and ejaculation, and/or inhibiting male cannibalistic tendencies in this species. Copyright © 2015 Elsevier B.V. All rights reserved.

Conditioning to colors: a population assay for visual learning in Drosophila.

PubMed

van Swinderen, Bruno

2011-11-01

Vision is a major sensory modality in Drosophila behavior, with more than one-half of the Drosophila brain devoted to visual processing. The mechanisms of vision in Drosophila can be studied in individuals and in populations of flies by using various paradigms. Although there has never been a widely used population assay for visual learning in Drosophila, some population paradigms have shown significant visual learning. These studies use colors as conditioned stimuli (CS) and shaking as the unconditioned stimulus (US). A simple version of the paradigm, conditioning to colors using a shaking device, is described here. A conditioning chamber, called a crab, is designed to center the flies after shaking by having them tumble down to the lowest point between joined glass tubes forming a V. Thus, vibration should be just strong enough to center most flies. After shaking, flies display a geotactic response and climb up either side of the V, and their choice of which side to climb is influenced by color displays on either side. The proportion of flies on either side determines the flies' natural preference or their learned avoidance of a color associated with shaking.

A Compatibility Assessment and Comparison of the Flame Resistant Chemical-Biological (CB) Overgarment with the Standard ’A’ CB Overgarment.

DTIC Science & Technology

1982-01-01

Overgarment-Dynamics .............. .19 TABLES 1. Basic Anthropometry .......... ...................... 3 2. Flame Resistant CB Overgarment Test...participants (TPs) during this evaluation. Basic anthropometry of these subjects is given in Table I. TABLE 1 Basic Anthropometry Mean SD Maximum...5 S H L XL 39 H L XL XXL 43 L XL XXL XXL The areas considered were ease of doffing and donning, compatibility with prescribed clothing and field

Process for removing thorium and recovering vanadium from titanium chlorinator waste

DOEpatents

Olsen, Richard S.; Banks, John T.

1996-01-01

A process for removal of thorium from titanium chlorinator waste comprising: (a) leaching an anhydrous titanium chlorinator waste in water or dilute hydrochloric acid solution and filtering to separate insoluble minerals and coke fractions from soluble metal chlorides; (b) beneficiating the insoluble fractions from step (a) on shaking tables to recover recyclable or otherwise useful TiO.sub.2 minerals and coke; and (c) treating filtrate from step (a) with reagents to precipitate and remove thorium by filtration along with acid metals of Ti, Zr, Nb, and Ta by the addition of the filtrate (a), a base and a precipitant to a boiling slurry of reaction products (d); treating filtrate from step (c) with reagents to precipitate and recover an iron vanadate product by the addition of the filtrate (c), a base and an oxidizing agent to a boiling slurry of reaction products; and (e) treating filtrate from step (d) to remove any remaining cations except Na by addition of Na.sub.2 CO.sub.3 and boiling.

Evaluating Post-Earthquake Building Safety Using Economical MEMS Seismometers

PubMed Central

Yin, Ren-Cheng

2018-01-01

The earthquake early warning (EEW)-research group at National Taiwan University has been developing a microelectromechanical system-based accelerometer called “P-Alert”, designed for issuing EEWs. The main advantage of P-Alert is that it is a relatively economical seismometer. However, because of the expensive nature of commercial hardware for structural health monitoring (SHM) systems, the application of SHM to buildings remains limited. To determine the performance of P-Alert for evaluating post-earthquake building safety, we conducted a series of steel-frame shaking table tests with incremental damage. We used the fragility curves of different damage levels and the interstory drift ratios (calculated by the measured acceleration of each story using double integration and a filter) to gauge the potential damage levels. We concluded that the acceptable detection of damage for an entire building is possible. With improvements to the synchronization of the P-Alert sensors, we also anticipate a damage localization feature for the stories of a building. PMID:29734736

Wing walls for enhancing the seismic performance of reinforced concrete frame structures

NASA Astrophysics Data System (ADS)

Yang, Weisong; Guo, Xun; Xu, Weixiao; Yuan, Xin

2016-06-01

A building retrofitted with wing walls in the bottom story, which was damaged during the 2008 M8.0 Wenchuan earthquake in China, is introduced and a corresponding 1/4 scale wing wall-frame model was subjected to shake table motions to study the seismic behavior of this retrofitted structural system. The results show that wing walls can effectively protect columns from damage by moving areas that bear reciprocating tension and compression to the sections of the wing walls, thus achieving an extra measure of seismic fortification. A `strong column-weak beam' mechanism was realized, the flexural rigidity of the vertical member was strengthened, and a more uniform distribution of deformation among all the stories was measured. In addition, the joint between the wing walls and the beams suffered severe damage during the tests, due to an area of local stress concentration. A longer area of intensive stirrup is suggested in the end of the beams.

A synchronized multipoint vision-based system for displacement measurement of civil infrastructures.

PubMed

Ho, Hoai-Nam; Lee, Jong-Han; Park, Young-Soo; Lee, Jong-Jae

2012-01-01

This study presents an advanced multipoint vision-based system for dynamic displacement measurement of civil infrastructures. The proposed system consists of commercial camcorders, frame grabbers, low-cost PCs, and a wireless LAN access point. The images of target panels attached to a structure are captured by camcorders and streamed into the PC via frame grabbers. Then the displacements of targets are calculated using image processing techniques with premeasured calibration parameters. This system can simultaneously support two camcorders at the subsystem level for dynamic real-time displacement measurement. The data of each subsystem including system time are wirelessly transferred from the subsystem PCs to master PC and vice versa. Furthermore, synchronization process is implemented to ensure the time synchronization between the master PC and subsystem PCs. Several shaking table tests were conducted to verify the effectiveness of the proposed system, and the results showed very good agreement with those from a conventional sensor with an error of less than 2%.

A Synchronized Multipoint Vision-Based System for Displacement Measurement of Civil Infrastructures

PubMed Central

Ho, Hoai-Nam; Lee, Jong-Han; Park, Young-Soo; Lee, Jong-Jae

2012-01-01

This study presents an advanced multipoint vision-based system for dynamic displacement measurement of civil infrastructures. The proposed system consists of commercial camcorders, frame grabbers, low-cost PCs, and a wireless LAN access point. The images of target panels attached to a structure are captured by camcorders and streamed into the PC via frame grabbers. Then the displacements of targets are calculated using image processing techniques with premeasured calibration parameters. This system can simultaneously support two camcorders at the subsystem level for dynamic real-time displacement measurement. The data of each subsystem including system time are wirelessly transferred from the subsystem PCs to master PC and vice versa. Furthermore, synchronization process is implemented to ensure the time synchronization between the master PC and subsystem PCs. Several shaking table tests were conducted to verify the effectiveness of the proposed system, and the results showed very good agreement with those from a conventional sensor with an error of less than 2%. PMID:23028250

Application of higher order SVD to vibration-based system identification and damage detection

NASA Astrophysics Data System (ADS)

Chao, Shu-Hsien; Loh, Chin-Hsiung; Weng, Jian-Huang

2012-04-01

Singular value decomposition (SVD) is a powerful linear algebra tool. It is widely used in many different signal processing methods, such principal component analysis (PCA), singular spectrum analysis (SSA), frequency domain decomposition (FDD), subspace identification and stochastic subspace identification method ( SI and SSI ). In each case, the data is arranged appropriately in matrix form and SVD is used to extract the feature of the data set. In this study three different algorithms on signal processing and system identification are proposed: SSA, SSI-COV and SSI-DATA. Based on the extracted subspace and null-space from SVD of data matrix, damage detection algorithms can be developed. The proposed algorithm is used to process the shaking table test data of the 6-story steel frame. Features contained in the vibration data are extracted by the proposed method. Damage detection can then be investigated from the test data of the frame structure through subspace-based and nullspace-based damage indices.

The dynamic characteristics of a turbo-rotor simulator supported on gas-lubricated foil bearings. Part 1: Response to rotating imbalance and unidirectional excitation

NASA Technical Reports Server (NTRS)

Licht, L.

1970-01-01

A sixteen-inch rotor, weighing approximately twenty-one pounds, was supported by air-lubricated foil bearings. In physical size and in mass distribution, the rotor closely matched that of an experimental Brayton cycle turboalternator unit. The rotor was stable in both vertical horizontal attitudes at speeds up to 50,000 rpm. A detailed description of the experimental apparatus and of the foil bearing design are given. The paper contains data on response of the rotor to rotating imbalance, symmetric and asymmetric, and to excitation by means of a vibrator (shake table). It is concluded that the gas-lubricated foil bearing suspension is free from fractional frequency whirl and suffers no loss of load capacity when excited at frequency equal to half the rotational speed. In contrast to rigid gas bearings, the foil bearing imposes no stringent requirements with respect to dimensional tolerances, cleanliness, or limitations of journal motion within the narrow confines of bearing clearance.

Evaluating Post-Earthquake Building Safety Using Economical MEMS Seismometers.

PubMed

Hsu, Ting-Yu; Yin, Ren-Cheng; Wu, Yih-Min

2018-05-05

The earthquake early warning (EEW)-research group at National Taiwan University has been developing a microelectromechanical system-based accelerometer called “P-Alert”, designed for issuing EEWs. The main advantage of P-Alert is that it is a relatively economical seismometer. However, because of the expensive nature of commercial hardware for structural health monitoring (SHM) systems, the application of SHM to buildings remains limited. To determine the performance of P-Alert for evaluating post-earthquake building safety, we conducted a series of steel-frame shaking table tests with incremental damage. We used the fragility curves of different damage levels and the interstory drift ratios (calculated by the measured acceleration of each story using double integration and a filter) to gauge the potential damage levels. We concluded that the acceptable detection of damage for an entire building is possible. With improvements to the synchronization of the P-Alert sensors, we also anticipate a damage localization feature for the stories of a building.

Damage detection of structures identified with deterministic-stochastic models using seismic data.

PubMed

Huang, Ming-Chih; Wang, Yen-Po; Chang, Ming-Lian

2014-01-01

A deterministic-stochastic subspace identification method is adopted and experimentally verified in this study to identify the equivalent single-input-multiple-output system parameters of the discrete-time state equation. The method of damage locating vector (DLV) is then considered for damage detection. A series of shaking table tests using a five-storey steel frame has been conducted. Both single and multiple damage conditions at various locations have been considered. In the system identification analysis, either full or partial observation conditions have been taken into account. It has been shown that the damaged stories can be identified from global responses of the structure to earthquakes if sufficiently observed. In addition to detecting damage(s) with respect to the intact structure, identification of new or extended damages of the as-damaged counterpart has also been studied. This study gives further insights into the scheme in terms of effectiveness, robustness, and limitation for damage localization of frame systems.

Review of the Usefulness of Various Rotational Seismometers with Laboratory Results of Fibre-Optic Ones Tested for Engineering Applications

PubMed Central

Jaroszewicz, Leszek R.; Kurzych, Anna; Krajewski, Zbigniew; Marć, Paweł; Kowalski, Jerzy K.; Bobra, Piotr; Zembaty, Zbigniew; Sakowicz, Bartosz; Jankowski, Robert

2016-01-01

Starting with descriptions of rotational seismology, areas of interest and historical field measurements, the fundamental requirements for rotational seismometers for seismological and engineering application are formulated. On the above basis, a review of all existing rotational seismometers is presented with a description of the principles of their operation as well as possibilities to fulfill formulated requirements. This review includes mechanical, acoustical, electrochemical and optical devices and shows that the last of these types are the most promising. It is shown that optical rotational seismometer based on the ring-laser gyroscope concept is the best for seismological applications, whereas systems based on fiber-optic gyroscopes demonstrate parameters which are also required for engineering applications. Laboratory results of the Fibre-Optic System for Rotational Events & Phenomena Monitoring using a small 1-D shaking table modified to generate rotational excitations are presented. The harmonic and time-history tests demonstrate its usefulness for recording rotational motions with rates up to 0.25 rad/s. PMID:27999299

Comparison of Sedentary Behaviors in Office Workers Using Sit-Stand Tables With and Without Semiautomated Position Changes.

PubMed

Barbieri, Dechristian França; Srinivasan, Divya; Mathiassen, Svend Erik; Oliveira, Ana Beatriz

2017-08-01

We compared usage patterns of two different electronically controlled sit-stand tables during a 2-month intervention period among office workers. Office workers spend most of their working time sitting, which is likely detrimental to health. Although the introduction of sit-stand tables has been suggested as an effective intervention to decrease sitting time, limited evidence is available on usage patterns of sit-stand tables and whether patterns are influenced by table configuration. Twelve workers were provided with standard sit-stand tables (nonautomated table group) and 12 with semiautomated sit-stand tables programmed to change table position according to a preset pattern, if the user agreed to the system-generated prompt (semiautomated table group). Table position was monitored continuously for 2 months after introducing the tables, as a proxy for sit-stand behavior. On average, the table was in a "sit" position for 85% of the workday in both groups; this percentage did not change significantly during the 2-month period. Switches in table position from sit to stand were, however, more frequent in the semiautomated table group than in the nonautomated table group (0.65 vs. 0.29 hr -1 ; p = .001). Introducing a semiautomated sit-stand table appeared to be an attractive alternative to a standard sit-stand table, because it led to more posture variation. A semiautomated sit-stand table may effectively contribute to making postures more variable among office workers and thus aid in alleviating negative health effects of extensive sitting.

Field observations of seismic velocity changes caused by shaking-induced damage and healing due to mesoscopic nonlinearity

NASA Astrophysics Data System (ADS)

Gassenmeier, M.; Sens-Schönfelder, C.; Eulenfeld, T.; Bartsch, M.; Victor, P.; Tilmann, F.; Korn, M.

2016-03-01

To investigate temporal seismic velocity changes due to earthquake related processes and environmental forcing in Northern Chile, we analyse 8 yr of ambient seismic noise recorded by the Integrated Plate Boundary Observatory Chile (IPOC). By autocorrelating the ambient seismic noise field measured on the vertical components, approximations of the Green's functions are retrieved and velocity changes are measured with Coda Wave Interferometry. At station PATCX, we observe seasonal changes in seismic velocity caused by thermal stress as well as transient velocity reductions in the frequency range of 4-6 Hz. Sudden velocity drops occur at the time of mostly earthquake-induced ground shaking and recover over a variable period of time. We present an empirical model that describes the seismic velocity variations based on continuous observations of the local ground acceleration. The model assumes that not only the shaking of large earthquakes causes velocity drops, but any small vibrations continuously induce minor velocity variations that are immediately compensated by healing in the steady state. We show that the shaking effect is accumulated over time and best described by the integrated envelope of the ground acceleration over the discretization interval of the velocity measurements, which is one day. In our model, the amplitude of the velocity reduction as well as the recovery time are proportional to the size of the excitation. This model with two free scaling parameters fits the data of the shaking induced velocity variation in remarkable detail. Additionally, a linear trend is observed that might be related to a recovery process from one or more earthquakes before our measurement period. A clear relationship between ground shaking and induced velocity reductions is not visible at other stations. We attribute the outstanding sensitivity of PATCX to ground shaking and thermal stress to the special geological setting of the station, where the subsurface material consists of relatively loose conglomerate with high pore volume leading to a stronger nonlinearity compared to the other IPOC stations.

A Field-Shaking System to Reduce the Screening Current-Induced Field in the 800-MHz HTS Insert of the MIT 1.3-GHz LTS/HTS NMR Magnet: A Small-Model Study.

PubMed

Lee, Jiho; Park, Dongkeun; Michael, Philip C; Noguchi, So; Bascuñán, Juan; Iwasa, Yukikazu

2018-04-01

In this paper, we present experimental results, of a small-model study, from which we plan to develop and apply a full-scale field-shaking system to reduce the screening current-induced field (SCF) in the 800-MHz HTS Insert (H800) of the MIT 1.3-GHz LTS/HTS NMR magnet (1.3G) currently under construction-the H800 is composed of 3 nested coils, each a stack of no-insulation (NI) REBCO double-pancakes. In 1.3G, H800 is the chief source of a large error field generated by its own SCF. To study the effectiveness of the field-shaking technique, we used two NI REBCO double-pancakes, one from Coil 2 (HCoil2) and one from Coil 3 (HCoil3) of the 3 H800 coils, and placed them in the bore of a 5-T/300-mm room-temperature bore low-temperature superconducting (LTS) background magnet. The background magnet is used not only to induce the SCF in the double-pancakes but also to reduce it by the field-shaking technique. For each run, we induced the SCF in the double-pancakes at an axial location where the external radial field Br > 0, then for the field-shaking, moved them to another location where the external axial field Bz ≫ B R . Due to the geometry of H800 and L500, top double-pancakes of 3 H800 coils will experience the considerable radial magnetic field perpendicular to the REBCO tape surface. To examine the effect of the field-shaking on the SCF, we tested each NI REBCO DP in the absence or presence of a radial field. In this paper, we report 77-K experimental results and analysis of the effect and a few significant remarks of the field-shaking.

ShakeMap fed by macroseismic data in France: feedbacks and contribution for improving SHA.

NASA Astrophysics Data System (ADS)

Schlupp, A.

2016-12-01

We are using the USGS ShakeMap software V3.5 that allows including intensity as input in association with instrumental data. We have been collecting citizen testimonies for 17 years in France, a region of moderate seismicity for the metropolitan part and in a subduction context for the West Indies part. We collect frequently several thousands testimonies after Mw>≈4.5. Thanks to the selection of "intensity characteristic thumbnails", we can provide in real time a single questionnary intensity (SQI) averaged at the city scale for a preliminary EMS98 intensity. We observed that about 65% of these "thumbnails SQI" are identical to the "final expert SQI" and the remaining part is shifted by only an intensity degree. With about 36000 cities (1 per 14 square km), we are able to sample in details the territory when the about 400 seismic stations give irreplaceable precise ground motion parameters but very local and most of the times at a farther epicentral distance. Since 2012, we contribute as intensity provider for ShakeMap in Pyrenees range (www.SisPyr.eu). Since spring 2016, we run the ShakeMap V3.5 in a "beta version" for the whole territory of France with several adaptations for region with moderate size events. The BCSF provides Intensities (www.franceseisme.fr), RESIF the instrumental data (www.resif.fr) with the West Indies observatories (OVSG-OVSM) and few stations of bordering countries. Feedbacks are: a huge improvement at any distance by including intensities, need to use regional attenuation law, detection of important ML overestimation in few regions, strong dependence to the epicenter localization, recent published GMICE well adapted, difficulty to represent non circular isoseismals. What we learn from ShakeMap is also a valuable contribution for hazard assessment. We aim to continuously improve the results for a state reference ShakeMap through a specific "ShakeMap transverse action" and its working group in the frame of RESIF.

Expanding CyberShake Physics-Based Seismic Hazard Calculations to Central California

NASA Astrophysics Data System (ADS)

Silva, F.; Callaghan, S.; Maechling, P. J.; Goulet, C. A.; Milner, K. R.; Graves, R. W.; Olsen, K. B.; Jordan, T. H.

2016-12-01

As part of its program of earthquake system science, the Southern California Earthquake Center (SCEC) has developed a simulation platform, CyberShake, to perform physics-based probabilistic seismic hazard analysis (PSHA) using 3D deterministic wave propagation simulations. CyberShake performs PSHA by first simulating a tensor-valued wavefield of Strain Green Tensors. CyberShake then takes an earthquake rupture forecast and extends it by varying the hypocenter location and slip distribution, resulting in about 500,000 rupture variations. Seismic reciprocity is used to calculate synthetic seismograms for each rupture variation at each computation site. These seismograms are processed to obtain intensity measures, such as spectral acceleration, which are then combined with probabilities from the earthquake rupture forecast to produce a hazard curve. Hazard curves are calculated at seismic frequencies up to 1 Hz for hundreds of sites in a region and the results interpolated to obtain a hazard map. In developing and verifying CyberShake, we have focused our modeling in the greater Los Angeles region. We are now expanding the hazard calculations into Central California. Using workflow tools running jobs across two large-scale open-science supercomputers, NCSA Blue Waters and OLCF Titan, we calculated 1-Hz PSHA results for over 400 locations in Central California. For each location, we produced hazard curves using both a 3D central California velocity model created via tomographic inversion, and a regionally averaged 1D model. These new results provide low-frequency exceedance probabilities for the rapidly expanding metropolitan areas of Santa Barbara, Bakersfield, and San Luis Obispo, and lend new insights into the effects of directivity-basin coupling associated with basins juxtaposed to major faults such as the San Andreas. Particularly interesting are the basin effects associated with the deep sediments of the southern San Joaquin Valley. We will compare hazard estimates from the 1D and 3D models, summarize the challenges of expanding CyberShake to a new geographic region, and describe our future CyberShake plans.

Shaking Alone Induces De Novo Conversion of Recombinant Prion Proteins to β-Sheet Rich Oligomers and Fibrils

PubMed Central

Ladner-Keay, Carol L.; Griffith, Bethany J.; Wishart, David S.

2014-01-01

The formation of β-sheet rich prion oligomers and fibrils from native prion protein (PrP) is thought to be a key step in the development of prion diseases. Many methods are available to convert recombinant prion protein into β-sheet rich fibrils using various chemical denaturants (urea, SDS, GdnHCl), high temperature, phospholipids, or mildly acidic conditions (pH 4). Many of these methods also require shaking or another form of agitation to complete the conversion process. We have identified that shaking alone causes the conversion of recombinant PrP to β-sheet rich oligomers and fibrils at near physiological pH (pH 5.5 to pH 6.2) and temperature. This conversion does not require any denaturant, detergent, or any other chemical cofactor. Interestingly, this conversion does not occur when the water-air interface is eliminated in the shaken sample. We have analyzed shaking-induced conversion using circular dichroism, resolution enhanced native acidic gel electrophoresis (RENAGE), electron microscopy, Fourier transform infrared spectroscopy, thioflavin T fluorescence and proteinase K resistance. Our results show that shaking causes the formation of β-sheet rich oligomers with a population distribution ranging from octamers to dodecamers and that further shaking causes a transition to β-sheet fibrils. In addition, we show that shaking-induced conversion occurs for a wide range of full-length and truncated constructs of mouse, hamster and cervid prion proteins. We propose that this method of conversion provides a robust, reproducible and easily accessible model for scrapie-like amyloid formation, allowing the generation of milligram quantities of physiologically stable β-sheet rich oligomers and fibrils. These results may also have interesting implications regarding our understanding of prion conversion and propagation both within the brain and via techniques such as protein misfolding cyclic amplification (PMCA) and quaking induced conversion (QuIC). PMID:24892647

Earthquake Early Warning: User Education and Designing Effective Messages

NASA Astrophysics Data System (ADS)

Burkett, E. R.; Sellnow, D. D.; Jones, L.; Sellnow, T. L.

2014-12-01

The U.S. Geological Survey (USGS) and partners are transitioning from test-user trials of a demonstration earthquake early warning system (ShakeAlert) to deciding and preparing how to implement the release of earthquake early warning information, alert messages, and products to the public and other stakeholders. An earthquake early warning system uses seismic station networks to rapidly gather information about an occurring earthquake and send notifications to user devices ahead of the arrival of potentially damaging ground shaking at their locations. Earthquake early warning alerts can thereby allow time for actions to protect lives and property before arrival of damaging shaking, if users are properly educated on how to use and react to such notifications. A collaboration team of risk communications researchers and earth scientists is researching the effectiveness of a chosen subset of potential earthquake early warning interface designs and messages, which could be displayed on a device such as a smartphone. Preliminary results indicate, for instance, that users prefer alerts that include 1) a map to relate their location to the earthquake and 2) instructions for what to do in response to the expected level of shaking. A number of important factors must be considered to design a message that will promote appropriate self-protective behavior. While users prefer to see a map, how much information can be processed in limited time? Are graphical representations of wavefronts helpful or confusing? The most important factor to promote a helpful response is the predicted earthquake intensity, or how strong the expected shaking will be at the user's location. Unlike Japanese users of early warning, few Californians are familiar with the earthquake intensity scale, so we are exploring how differentiating instructions between intensity levels (e.g., "Be aware" for lower shaking levels and "Drop, cover, hold on" at high levels) can be paired with self-directed supplemental information to increase the public's understanding of earthquake shaking and protective behaviors.

Project of Near-Real-Time Generation of ShakeMaps and a New Hazard Map in Austria

NASA Astrophysics Data System (ADS)

Jia, Yan; Weginger, Stefan; Horn, Nikolaus; Hausmann, Helmut; Lenhardt, Wolfgang

2016-04-01

Target-orientated prevention and effective crisis management can reduce or avoid damage and save lives in case of a strong earthquake. To achieve this goal, a project for automatic generated ShakeMaps (maps of ground motion and shaking intensity) and updating the Austrian hazard map was started at ZAMG (Zentralanstalt für Meteorologie und Geodynamik) in 2015. The first goal of the project is set for a near-real-time generation of ShakeMaps following strong earthquakes in Austria to provide rapid, accurate and official information to support the governmental crisis management. Using newly developed methods and software by SHARE (Seismic Hazard Harmonization in Europe) and GEM (Global Earthquake Model), which allows a transnational analysis at European level, a new generation of Austrian hazard maps will be ultimately calculated. More information and a status of our project will be given by this presentation.

Automatic Extraction of Drug Adverse Effects from Product Characteristics (SPCs): A Text Versus Table Comparison.

PubMed

Lamy, Jean-Baptiste; Ugon, Adrien; Berthelot, Hélène

2016-01-01

Potential adverse effects (AEs) of drugs are described in their summary of product characteristics (SPCs), a textual document. Automatic extraction of AEs from SPCs is useful for detecting AEs and for building drug databases. However, this task is difficult because each AE is associated with a frequency that must be extracted and the presentation of AEs in SPCs is heterogeneous, consisting of plain text and tables in many different formats. We propose a taxonomy for the presentation of AEs in SPCs. We set up natural language processing (NLP) and table parsing methods for extracting AEs from texts and tables of any format, and evaluate them on 10 SPCs. Automatic extraction performed better on tables than on texts. Tables should be recommended for the presentation of the AEs section of the SPCs.

Liquid films on shake flask walls explain increasing maximum oxygen transfer capacities with elevating viscosity.

PubMed

Giese, Heiner; Azizan, Amizon; Kümmel, Anne; Liao, Anping; Peter, Cyril P; Fonseca, João A; Hermann, Robert; Duarte, Tiago M; Büchs, Jochen

2014-02-01

In biotechnological screening and production, oxygen supply is a crucial parameter. Even though oxygen transfer is well documented for viscous cultivations in stirred tanks, little is known about the gas/liquid oxygen transfer in shake flask cultures that become increasingly viscous during cultivation. Especially the oxygen transfer into the liquid film, adhering on the shake flask wall, has not yet been described for such cultivations. In this study, the oxygen transfer of chemical and microbial model experiments was measured and the suitability of the widely applied film theory of Higbie was studied. With numerical simulations of Fick's law of diffusion, it was demonstrated that Higbie's film theory does not apply for cultivations which occur at viscosities up to 10 mPa s. For the first time, it was experimentally shown that the maximum oxygen transfer capacity OTRmax increases in shake flasks when viscosity is increased from 1 to 10 mPa s, leading to an improved oxygen supply for microorganisms. Additionally, the OTRmax does not significantly undermatch the OTRmax at waterlike viscosities, even at elevated viscosities of up to 80 mPa s. In this range, a shake flask is a somehow self-regulating system with respect to oxygen supply. This is in contrary to stirred tanks, where the oxygen supply is steadily reduced to only 5% at 80 mPa s. Since, the liquid film formation at shake flask walls inherently promotes the oxygen supply at moderate and at elevated viscosities, these results have significant implications for scale-up. © 2013 Wiley Periodicals, Inc.

Development of a circulation direct sampling and monitoring system for O2 and CO2 concentrations in the gas-liquid phases of shake-flask systems during microbial cell culture.

PubMed

Takahashi, Masato; Sawada, Yoshisuke; Aoyagi, Hideki

2017-08-23

Monitoring the environmental factors during shake-flask culture of microorganisms can help to optimise the initial steps of bioprocess development. Herein, we developed a circulation direct monitoring and sampling system (CDMSS) that can monitor the behaviour of CO 2 and O 2 in the gas-liquid phases and obtain a sample without interrupting the shaking of the culture in Erlenmeyer flasks capped with breathable culture plugs. Shake-flask culturing of Escherichia coli using this set-up indicated that a high concentration of CO 2 accumulated not only in the headspace (maximum ~100 mg/L) but also in the culture broth (maximum ~85 mg/L) during the logarithmic phase (4.5-9.0 h). By packing a CO 2 absorbent in the gas circulation unit of CDMSS, a specialised shake-flask culture was developed to remove CO 2 from the headspace. It was posited that removing CO 2 from the headspace would suppress increases in the dissolved CO 2 concentration in the culture broth (maximum ~15 mg/L). Furthermore, the logarithmic growth phase (4.5-12.0 h) was extended, the U.O.D. 580 and pH value increased, and acetic acid concentration was reduced, compared with the control. To our knowledge, this is the first report of a method aimed at improving the growth of E. coli cells without changing the composition of the medium, temperature, and shaking conditions.

Cascadia Onshore-Offshore Site Response, Submarine Sediment Mobilization, and Earthquake Recurrence

NASA Astrophysics Data System (ADS)

Gomberg, J.

2018-02-01

Local geologic structure and topography may modify arriving seismic waves. This inherent variation in shaking, or "site response," may affect the distribution of slope failures and redistribution of submarine sediments. I used seafloor seismic data from the 2011 to 2015 Cascadia Initiative and permanent onshore seismic networks to derive estimates of site response, denoted Sn, in low- and high-frequency (0.02-1 and 1-10 Hz) passbands. For three shaking metrics (peak velocity and acceleration and energy density) Sn varies similarly throughout Cascadia and changes primarily in the direction of convergence, roughly east-west. In the two passbands, Sn patterns offshore are nearly opposite and range over an order of magnitude or more across Cascadia. Sn patterns broadly may be attributed to sediment resonance and attenuation. This and an abrupt step in the east-west trend of Sn suggest that changes in topography and structure at the edge of the continental margin significantly impact shaking. These patterns also correlate with gravity lows diagnostic of marginal basins and methane plumes channeled within shelf-bounding faults. Offshore Sn exceeds that onshore in both passbands, and the steepest slopes and shelf coincide with the relatively greatest and smallest Sn estimates at low and high frequencies, respectively; these results should be considered in submarine shaking-triggered slope stability failure studies. Significant north-south Sn variations are not apparent, but sparse sampling does not permit rejection of the hypothesis that the southerly decrease in intervals between shaking-triggered turbidites and great earthquakes inferred by Goldfinger et al. (2012, 2013, 2016) and Priest et al. (2017) is due to inherently stronger shaking southward.

The Development of Administrative Measures as Indicators of Soldier Effectiveness

DTIC Science & Technology

1987-08-01

26 CONTENTS (Continued) Page LIST OF TABLES (Continued) Table 13. Frequency distributions for selected variables: MPRJ/ EMF comparison 28 14...8217,»j«’N-j.,’j’«>,’j.’«J.>>>Ji’v-.%j.*’j">J,X Table 13 Frequency Distributions for Selected Variables: (n = 650 soldiers) MPRJ/ EMF Comparioon...information were examined: (a) the Enlisted Master File ( EMF ), a central computer record of selected personnel actions; (b) the Official Military Personnel

Post-Earthquake Assessment of Nevada Bridges Using ShakeMap/ShakeCast

DOT National Transportation Integrated Search

2016-01-01

Post-earthquake capacity of Nevada highway bridges is examined through a combination of engineering study and scenario earthquake evaluation. The study was undertaken by the University of Nevada Reno Department of Civil and Environmental Engineering ...

Strong Effects of Vs30 Heterogeneity on Physics-Based Scenario Ground-Shaking Computations

NASA Astrophysics Data System (ADS)

Louie, J. N.; Pullammanappallil, S. K.

2014-12-01

Hazard mapping and building codes worldwide use the vertically time-averaged shear-wave velocity between the surface and 30 meters depth, Vs30, as one predictor of earthquake ground shaking. Intensive field campaigns a decade ago in Reno, Los Angeles, and Las Vegas measured urban Vs30 transects with 0.3-km spacing. The Clark County, Nevada, Parcel Map includes urban Las Vegas and comprises over 10,000 site measurements over 1500 km2, completed in 2010. All of these data demonstrate fractal spatial statistics, with a fractal dimension of 1.5-1.8 at scale lengths from 0.5 km to 50 km. Vs measurements in boreholes up to 400 m deep show very similar statistics at 1 m to 200 m lengths. When included in physics-based earthquake-scenario ground-shaking computations, the highly heterogeneous Vs30 maps exhibit unexpectedly strong influence. In sensitivity tests (image below), low-frequency computations at 0.1 Hz display amplifications (as well as de-amplifications) of 20% due solely to Vs30. In 0.5-1.0 Hz computations, the amplifications are a factor of two or more. At 0.5 Hz and higher frequencies the amplifications can be larger than what the 1-d Building Code equations would predict from the Vs30 variations. Vs30 heterogeneities at one location have strong influence on amplifications at other locations, stretching out in the predominant direction of wave propagation for that scenario. The sensitivity tests show that shaking and amplifications are highly scenario-dependent. Animations of computed ground motions and how they evolve with time suggest that the fractal Vs30 variance acts to trap wave energy and increases the duration of shaking. Validations of the computations against recorded ground motions, possible in Las Vegas Valley due to the measurements of the Clark County Parcel Map, show that ground motion levels and amplifications match, while recorded shaking has longer duration than computed shaking. Several mechanisms may explain the amplification and increased duration of shaking in the presence of heterogeneous spatial distributions of Vs: conservation of wave energy across velocity changes; geometric focusing of waves by low-velocity lenses; vertical resonance and trapping; horizontal resonance and trapping; and multiple conversion of P- to S-wave energy.

Effects of the earthquake of March 27, 1964, on the Alaska highway system: Chapter C in The Alaska earthquake, March 27, 1964: effects on transportation, communications, and utilities

USGS Publications Warehouse

Kachadoorian, Reuben

1968-01-01

The great earthquake that struck Alaska about 5:36 p.m., Alaska standard time, Friday, March 27, 1964 (03:36:1.3.0, Greenwich mean time, March 28, 1964), severely crippled the highway system in the south-central part of the State. All the major highways and most secondary roads were impaired. Damage totaled more than $46 million, well over $25 million to bridges and nearly $21 million to roadways. Of the 204 bridges in south-central Alaska, 141 were damaged; 92 were severely damaged or destroyed. The earthquake damaged 186 of the 830 miles of roadway in south-central Alaska, 83 miles so severely that replacement or relocation was required. Earthquake damage to the roadways and bridges was chiefly by (1) seismic shaking, (2) compaction of fills as well as the underlying sediments, (3) lateral displacement of the roadway and bridges, (4) fractures, (5) landslides, (6) avalanches, (7) inundation by seismic sea waves, (8) scouring by seismic sea waves, (9) regional tectonic subsidence, causing inundation and erosion by high tides in subsided areas. The intensity of damage was controlled primarily by the geologic environment (including the depth of the water table) upon which the highway structures rested, and secondarily by the engineering characteristics of the structures. Structures on bedrock were only slightly damaged if at all, whereas those on unconsolidated sediments were slightly to severely damaged, or were completely destroyed by seismic shaking. The low-lying areas underlain by saturated sediments, such as the Snow River Crossing and Turnagain Arm sections of the Seward-Anchorage Highway, were the most severely damaged stretches of the highway system in south-central Alaska. At Snow River and Turnagain Arm, the sediments underlying the roadway are fine grained and the water table is shallow. These factors were responsible for the intense damage along this stretch of the highway. All the bridges on the Copper River Highway except for one on bedrock were damaged by seismic shaking. Lateral displacement of sediments toward a free face, which placed the bridges in compression, was the chief cause for the damage. This type of failure was extensive and widespread throughout the highway system. The chief engineering characteristics responsible for the type and intensity of damage include (1) thickness of roadway fills, (2) type of pile bents and masonry piers, (3) the weight ratio between the substructure and superstructure, and (4) the tie between the substructure and superstructure. The thicker the roadway fills, the more severe the damage. Wood piles did not break as extensively as piles constructed of three railroad rails welded together. Bridges that had relatively heavy superstructures, for example those with concrete decks on wood piles, were more severely damaged than those with all-wood or concrete decks or concrete piers. Failure first occurred at the tie between the superstructure and the substructure; the poorer this tie, the sooner the failure. Seismic sea waves destroyed 12 bridges on the Chiniak Highway on Kodiak Island, one bridge on Point Whitshed road near Cordova, and about 14 miles of roadway. The combination of regional tectonic subsidence and local subsidence and compaction of sediments caused inundation of many miles of highway by high tides, especially around Turnagain Arm. Total subsidence in some places amounted to more than 13 feet.

Producibility Analysis of the Alternative Antitank Airframe Configuration (AATAC) Flex-Wing

DTIC Science & Technology

1988-06-01

3 II. PRODUCTIONIPRODUCIBILITY CONSIDERATIONS ...................... 4 A. High Rage Manufacturing Issues...41 7. Hydroform process showing (1) blank in place, no pressure in cavity, (2) press closed and cavity pressurized, (3) ram... hydroforming and Guerin processes ..... 42 viI LIST OF TABLES Table Page 1. Comparison of Candidate Alloys ................................. 6 2. AATAC Wing

General Framework for Employment. Tableau de Bord. (Synoptic Table). Second Edition.

ERIC Educational Resources Information Center

Commission of the European Communities, Brussels (Belgium). Directorate-General for Employment, Industrial Relations and Social Affairs.

This synoptic table provides an overview and comparison of employment trends and policy measures for each member state of the European Community. Information on the following countries is presented in eight chapters: Belgium, Denmark, Germany, Greece, Spain, France, Ireland, Italy, Luxembourg, Netherlands, Portugal, and United Kingdom. Chapter 0…

Comparison of risk estimates using life-table methods.

PubMed

Sullivan, R E; Weng, P S

1987-08-01

Risk estimates promulgated by various radiation protection authorities in recent years have become increasingly more complex. Early "integral" estimates in the form of health effects per 0.01 person-Gy (per person-rad) or per 10(4) person-Gy (per 10(6) person-rad) have tended to be replaced by "differential" estimates which are age- and sex-dependent and specify both minimum induction (latency) and duration of risk expression (plateau) periods. These latter types of risk estimate must be used in conjunction with a life table in order to reduce them to integral form. In this paper, the life table has been used to effect a comparison of the organ and tissue risk estimates derived in several recent reports. In addition, a brief review of life-table methodology is presented and some features of the models used in deriving differential coefficients are discussed. While the great number of permutations possible with dose-response models, detailed risk estimates and proposed projection models precludes any unique result, the reduced integral coefficients are required to conform to the linear, absolute-risk model recommended for use with the integral risk estimates reviewed.

Colic

MedlinePlus

... prompted parents to shake or otherwise harm their child. Shaking a baby can cause serious damage to the brain and death. The risk of these uncontrolled reactions is greater if parents don't have information about soothing a crying child, education about colic and the support needed for ...

A versatile computer package for mechanism analysis, part 2: Dynamics and balance

NASA Astrophysics Data System (ADS)

Davies, T.

The algorithms required for the shaking force components, the shaking moment about the crankshaft axis, and the input torque and bearing load components are discussed using the textile machine as a focus for the discussion. The example is also used to provide illustrations of the output for options on the hodograph of the shaking force vector. This provides estimates of the optimum contrarotating masses and their locations for a generalized primary Lanchester balancer. The suitability of generalized Lanchester balancers particularly for textile machinery, and the overall strategy used during the development of the package are outlined.

Friability Testing as a New Stress-Stability Assay for Biopharmaceuticals.

PubMed

Torisu, Tetsuo; Maruno, Takahiro; Yoneda, Saki; Hamaji, Yoshinori; Honda, Shinya; Ohkubo, Tadayasu; Uchiyama, Susumu

2017-10-01

A cycle of dropping and shaking a vial containing antibody solution was reported to induce aggregation. In this study, antibody solutions in glass prefillable syringes with or without silicone oil lubrication were subjected to the combined stresses of dropping and shaking, using a friability testing apparatus. Larger numbers of subvisible particles were generated, regardless of silicone oil lubrication, upon combination stress exposure than that with shaking stress alone. Nucleation of antibody molecules upon perturbation by an impact of dropping and adsorption of antibody molecules to the syringe surface followed by film formation and antibody film desorption were considered key steps in the particle formation promoted by combination stress. A larger number of silicone oil droplets was released when silicone oil-lubricated glass syringes containing phosphate buffer saline were exposed to combination stress than that observed with shaking stress alone. Polysorbate 20, a non-ionic surfactant, effectively reduced the number of protein particles, but failed to prevent silicone oil release upon combination stress exposure. This study indicates that stress-stability assays using the friability testing apparatus are effective for assessing the stability of biopharmaceuticals under the combined stresses of dropping and shaking, which have not been tested in conventional stress-stability assays. Copyright © 2017 American Pharmacists Association®. Published by Elsevier Inc. All rights reserved.

Growth of plant root cultures in liquid- and gas-dispersed reactor environments.

PubMed

McKelvey, S A; Gehrig, J A; Hollar, K A; Curtis, W R

1993-01-01

The growth of Agrobacterium transformed "hairy root" cultures of Hyoscyamus muticus was examined in various liquid- and gas-dispersed bioreactor configurations. Reactor runs were replicated to provide statistical comparisons of nutrient availability on culture performance. Accumulated tissue mass in submerged air-sparged reactors was 31% of gyratory shake-flask controls. Experiments demonstrate that poor performance of sparged reactors is not due to bubble shear damage, carbon dioxide stripping, settling, or flotation of roots. Impaired oxygen transfer due to channeling and stagnation of the liquid phase are the apparent causes of poor growth. Roots grown on a medium-perfused inclined plane grew at 48% of gyratory controls. This demonstrates the ability of cultures to partially compensate for poor liquid distribution through vascular transport of nutrients. A reactor configuration in which the medium is sprayed over the roots and permitted to drain down through the root tissue was able to provide growth rates which are statistically indistinguishable (95% T-test) from gyratory shake-flask controls. In this type of spray/trickle-bed configuration, it is shown that distribution of the roots becomes a key factor in controlling the rate of growth. Implications of these results regarding design and scale-up of bioreactors to produce fine chemicals from root cultures are discussed.

Comparison of ground motions from hybrid simulations to nga prediction equations

USGS Publications Warehouse

Star, L.M.; Stewart, J.P.; Graves, R.W.

2011-01-01

We compare simulated motions for a Mw 7.8 rupture scenario on the San Andreas Fault known as the ShakeOut event, two permutations with different hypocenter locations, and a Mw 7.15 Puente Hills blind thrust scenario, to median and dispersion predictions from empirical NGA ground motion prediction equations. We find the simulated motions attenuate faster with distance than is predicted by the NGA models for periods less than about 5.0 s After removing this distance attenuation bias, the average residuals of the simulated events (i.e., event terms) are generally within the scatter of empirical event terms, although the ShakeOut simulation appears to be a high static stress drop event. The intraevent dispersion in the simulations is lower than NGA values at short periods and abruptly increases at 1.0 s due to different simulation procedures at short and long periods. The simulated motions have a depth-dependent basin response similar to the NGA models, and also show complex effects in which stronger basin response occurs when the fault rupture transmits energy into a basin at low angle, which is not predicted by the NGA models. Rupture directivity effects are found to scale with the isochrone parameter ?? 2011, Earthquake Engineering Research Institute.

Feasibility study of earthquake early warning (EEW) in Hawaii

USGS Publications Warehouse

Thelen, Weston A.; Hotovec-Ellis, Alicia J.; Bodin, Paul

2016-09-30

The effects of earthquake shaking on the population and infrastructure across the State of Hawaii could be catastrophic, and the high seismic hazard in the region emphasizes the likelihood of such an event. Earthquake early warning (EEW) has the potential to give several seconds of warning before strong shaking starts, and thus reduce loss of life and damage to property. The two approaches to EEW are (1) a network approach (such as ShakeAlert or ElarmS) where the regional seismic network is used to detect the earthquake and distribute the alarm and (2) a local approach where a critical facility has a single seismometer (or small array) and a warning system on the premises.The network approach, also referred to here as ShakeAlert or ElarmS, uses the closest stations within a regional seismic network to detect and characterize an earthquake. Most parameters used for a network approach require observations on multiple stations (typically 3 or 4), which slows down the alarm time slightly, but the alarms are generally more reliable than with single-station EEW approaches. The network approach also benefits from having stations closer to the source of any potentially damaging earthquake, so that alarms can be sent ahead to anyone who subscribes to receive the notification. Thus, a fully implemented ShakeAlert system can provide seconds of warning for both critical facilities and general populations ahead of damaging earthquake shaking.The cost to implement and maintain a fully operational ShakeAlert system is high compared to a local approach or single-station solution, but the benefits of a ShakeAlert system would be felt statewide—the warning times for strong shaking are potentially longer for most sources at most locations.The local approach, referred to herein as “single station,” uses measurements from a single seismometer to assess whether strong earthquake shaking can be expected. Because of the reliance on a single station, false alarms are more common than when using a regional network of seismometers. Given the current network, a single-station approach provides more warning for damaging earthquakes that occur close to the station, but it would have limited benefit compared to a fully implemented ShakeAlert system. For Honolulu, for example, the single-station approach provides an advantage over ShakeAlert only for earthquakes that occur in a narrow zone extending northeast and southwest of O‘ahu. Instrumentation and alarms associated with the single-station approach are typically maintained and assessed within the target facility, and thus no outside connectivity is required. A single-station approach, then, is unlikely to help broader populations beyond the individuals at the target facility, but they have the benefit of being commercially available for relatively little cost. The USGS Hawaiian Volcano Observatory (HVO) is the Advanced National Seismic System (ANSS) regional seismic network responsible for locating and characterizing earthquakes across the State of Hawaii. During 2014 and 2015, HVO tested a network-based EEW algorithm within the current seismic network in order to assess the suitability for building a full EEW system. Using the current seismic instrumentation and processing setup at HVO, it is possible for a network approach to release an alarm a little more than 3 seconds after the earthquake is recorded on the fourth seismometer. Presently, earthquakes having M≥3 detected with the ElarmS algorithm have an average location error of approximately 4.5 km and an average magnitude error of -0.3 compared to the reviewed catalog locations from the HVO. Additional stations and upgrades to existing seismic stations would serve to improve solution precision and warning times and additional staffing would be required to provide support for a robust, network-based EEW system. For a critical facility on the Island of Hawaiʻi, such as the telescopes atop Mauna Kea, one phased approach to mitigate losses could be to immediately install a single station system to establish some level of warning. Subsequently, supporting the implementation of a full network-based EEW system on the Island of Hawaiʻi would provide additional benefit in the form of improved warning times once the system is fully installed and operational, which may take several years. Distributed populations across the Hawaiian Islands, including those outside the major cities and far from the likely earthquake source areas, would likely only benefit from a network approach such as ShakeAlert to provide warnings of strong shaking.

Practical Applications for Earthquake Scenarios Using ShakeMap

NASA Astrophysics Data System (ADS)

Wald, D. J.; Worden, B.; Quitoriano, V.; Goltz, J.

2001-12-01

In planning and coordinating emergency response, utilities, local government, and other organizations are best served by conducting training exercises based on realistic earthquake situations-ones that they are most likely to face. Scenario earthquakes can fill this role; they can be generated for any geologically plausible earthquake or for actual historic earthquakes. ShakeMap Web pages now display selected earthquake scenarios (www.trinet.org/shake/archive/scenario/html) and more events will be added as they are requested and produced. We will discuss the methodology and provide practical examples where these scenarios are used directly for risk reduction. Given a selected event, we have developed tools to make it relatively easy to generate a ShakeMap earthquake scenario using the following steps: 1) Assume a particular fault or fault segment will (or did) rupture over a certain length, 2) Determine the magnitude of the earthquake based on assumed rupture dimensions, 3) Estimate the ground shaking at all locations in the chosen area around the fault, and 4) Represent these motions visually by producing ShakeMaps and generating ground motion input for loss estimation modeling (e.g., FEMA's HAZUS). At present, ground motions are estimated using empirical attenuation relationships to estimate peak ground motions on rock conditions. We then correct the amplitude at that location based on the local site soil (NEHRP) conditions as we do in the general ShakeMap interpolation scheme. Finiteness is included explicitly, but directivity enters only through the empirical relations. Although current ShakeMap earthquake scenarios are empirically based, substantial improvements in numerical ground motion modeling have been made in recent years. However, loss estimation tools, HAZUS for example, typically require relatively high frequency (3 Hz) input for predicting losses, above the range of frequencies successfully modeled to date. Achieving full-synthetic ground motion estimates that will substantially improve over empirical relations at these frequencies will require developing cost-effective numerical tools for proper theoretical inclusion of known complex ground motion effects. Current efforts underway must continue in order to obtain site, basin, and deeper crustal structure, and to characterize and test 3D earth models (including attenuation and nonlinearity). In contrast, longer period synthetics (>2 sec) are currently being generated in a deterministic fashion to include 3D and shallow site effects, an improvement on empirical estimates alone. As progress is made, we will naturally incorporate such advances into the ShakeMap scenario earthquake and processing methodology. Our scenarios are currently used heavily in emergency response planning and loss estimation. Primary users include city, county, state and federal government agencies (e.g., the California Office of Emergency Services, FEMA, the County of Los Angeles) as well as emergency response planners and managers for utilities, businesses, and other large organizations. We have found the scenarios are also of fundamental interest to many in the media and the general community interested in the nature of the ground shaking likely experienced in past earthquakes as well as effects of rupture on known faults in the future.

Mango Shake

MedlinePlus

... this page: https://medlineplus.gov/recipe/mangoshake.html Mango Shake To use the sharing features on this page, please enable JavaScript. Prep time: 5 minutes Cook time: 0 minutes ... cup low-fat (1 percent) milk 4 Tbsp frozen mango juice (or 1 fresh pitted mango) 1 small ...

VLBI2010 Receiver Back End Comparison

NASA Technical Reports Server (NTRS)

Petrachenko, Bill

2013-01-01

VLBI2010 requires a receiver back-end to convert analog RF signals from the receiver front end into channelized digital data streams to be recorded or transmitted electronically. The back end functions are typically performed in two steps: conversion of analog RF inputs into IF bands (see Table 2), and conversion of IF bands into channelized digital data streams (see Tables 1a, 1b and 1c). The latter IF systems are now completely digital and generically referred to as digital back ends (DBEs). In Table 2 two RF conversion systems are compared, and in Tables 1a, 1b, and 1c nine DBE systems are compared. Since DBE designs are advancing rapidly, the data in these tables are only guaranteed to be current near the update date of this document.

The Shrail: A Comparison of a Novel Attachable Rail System With the Current Deployment Operating Table.

PubMed

Dilday, Joshua; Sirkin, Maxwell R; Wertin, Thomas; Bradley, Frances; Hiles, Jason

The current forward surgical team (FST) operating table is heavy and burdensome and hinders essential movement flexibility. A novel attachable rail system, the Shrail, has been developed to overcome these obstacles. The Shrail turns a North Atlantic Treaty Organization litter into a functional operating table. A local FST compared the assembly of the FST operating table with assembling the Shrail. Device weight, storage space, and assembly space were directly measured and compared. The mean assembly time required for the Shrail was significantly less compared with the operating table (23.36 versus 151.6 seconds; p ≤ .01). The Shrail weighs less (6.80kg versus 73.03kg) and requires less storage space (0.019m3 versus 0.323m3) compared with the current FST operating table. The Shrail provides an FST with a faster, lighter surgical table assembly. For these reasons, it is better suited for the demands of an FST and the implementation of prolonged field care. 2018.

Scale-up from shake flasks to bioreactor, based on power input and Streptomyces lividans morphology, for the production of recombinant APA (45/47 kDa protein) from Mycobacterium tuberculosis.

PubMed

Gamboa-Suasnavart, Ramsés A; Marín-Palacio, Luz D; Martínez-Sotelo, José A; Espitia, Clara; Servín-González, Luis; Valdez-Cruz, Norma A; Trujillo-Roldán, Mauricio A

2013-08-01

Culture conditions in shake flasks affect filamentous Streptomyces lividans morphology, as well the productivity and O-mannosylation of recombinant Ala-Pro-rich O-glycoprotein (known as the 45/47 kDa or APA antigen) from Mycobacterium tuberculosis. In order to scale up from previous reported shake flasks to bioreactor, data from the literature on the effect of agitation on morphology of Streptomyces strains were used to obtain gassed volumetric power input values that can be used to obtain a morphology of S. lividans in bioreactor similar to the morphology previously reported in coiled/baffled shake flasks by our group. Morphology of S. lividans was successfully scaled-up, obtaining similar mycelial sizes in both scales with diameters of 0.21 ± 0.09 mm in baffled and coiled shake flasks, and 0.15 ± 0.01 mm in the bioreactor. Moreover, the specific growth rate was successfully scaled up (0.09 ± 0.02 and 0.12 ± 0.01 h(-1), for bioreactors and flasks, respectively), and the recombinant protein productivity measured by densitometry, as well. More interestingly, the quality of the recombinant glycoprotein measured as the amount of mannoses attached to the C-terminal of APA was also scaled- up; with up to five mannose residues in cultures carried out in shake flasks; and six in the bioreactor. However, final biomass concentration was not similar, indicating that although the process can be scaled-up using the power input, others factors like oxygen transfer rate, tip speed or energy dissipation/circulation function can be an influence on bacterial metabolism.

ShakeNet: a portable wireless sensor network for instrumenting large civil structures

USGS Publications Warehouse

Kohler, Monica D.; Hao, Shuai; Mishra, Nilesh; Govindan, Ramesh; Nigbor, Robert

2015-08-03

We report our findings from a U.S. Geological Survey (USGS) National Earthquake Hazards Reduction Program-funded project to develop and test a wireless, portable, strong-motion network of up to 40 triaxial accelerometers for structural health monitoring. The overall goal of the project was to record ambient vibrations for several days from USGS-instrumented structures. Structural health monitoring has important applications in fields like civil engineering and the study of earthquakes. The emergence of wireless sensor networks provides a promising means to such applications. However, while most wireless sensor networks are still in the experimentation stage, very few take into consideration the realistic earthquake engineering application requirements. To collect comprehensive data for structural health monitoring for civil engineers, high-resolution vibration sensors and sufficient sampling rates should be adopted, which makes it challenging for current wireless sensor network technology in the following ways: processing capabilities, storage limit, and communication bandwidth. The wireless sensor network has to meet expectations set by wired sensor devices prevalent in the structural health monitoring community. For this project, we built and tested an application-realistic, commercially based, portable, wireless sensor network called ShakeNet for instrumentation of large civil structures, especially for buildings, bridges, or dams after earthquakes. Two to three people can deploy ShakeNet sensors within hours after an earthquake to measure the structural response of the building or bridge during aftershocks. ShakeNet involved the development of a new sensing platform (ShakeBox) running a software suite for networking, data collection, and monitoring. Deployments reported here on a tall building and a large dam were real-world tests of ShakeNet operation, and helped to refine both hardware and software. 

Ocular motor characteristics of different subtypes of spinocerebellar ataxia: distinguishing features.

PubMed

Kim, Ji Sun; Kim, Ji Soo; Youn, Jinyoung; Seo, Dae-Won; Jeong, Yuri; Kang, Ji-Hoon; Park, Jeong Ho; Cho, Jin Whan

2013-08-01

Because of frequent involvement of the cerebellum and brainstem, ocular motor abnormalities are key features of spinocerebellar ataxias and may aid in differential diagnosis. Our objective for this study was to distinguish the subtypes by ophthalmologic features after head-shaking and positional maneuvers, which are not yet recognized as differential diagnostic tools in most common forms of spinocerebellar ataxias. Of the 302 patients with a diagnosis of cerebellar ataxia in 3 Korean University Hospitals from June 2011 to June 2012, 48 patients with spinocerebellar ataxia types 1, 2, 3, 6, 7, or 8 or with undetermined spinocerebellar ataxias were enrolled. All patients underwent a video-oculographic recording of fixation abnormalities, gaze-evoked nystagmus, positional and head-shaking nystagmus, and dysmetric saccades. Logistic regression analysis controlling for disease duration revealed that spontaneous and positional downbeat nystagmus and perverted head-shaking nystagmus were strong predictors for spinocerebellar ataxia 6, whereas saccadic intrusions and oscillations were identified as positive indicators of spinocerebellar ataxia 3. In contrast, the presence of gaze-evoked nystagmus and dysmetric saccades was a negative predictor of spinocerebellar ataxia 2. Positional maneuvers and horizontal head shaking occasionally induced or augmented saccadic intrusions/oscillations in patients with spinocerebellar ataxia types 1, 2, and 3 and undetermined spinocerebellar ataxia. The results indicated that perverted head-shaking nystagmus may be the most sensitive parameter for SCA6, whereas saccadic intrusions/oscillations are the most sensitive for spinocerebellar ataxia 3. In contrast, a paucity of gaze-evoked nystagmus and dysmetric saccades is more indicative of spinocerebellar ataxia 2. Head-shaking and positional maneuvers aid in defining ocular motor characteristics in spinocerebellar ataxias. © 2013 Movement Disorder Society. Copyright © 2013 Movement Disorder Society.

Development of a Low Cost Earthquake Early Warning System in Taiwan

NASA Astrophysics Data System (ADS)

Wu, Y. M.

2017-12-01

The National Taiwan University (NTU) developed an earthquake early warning (EEW) system for research purposes using low-cost accelerometers (P-Alert) since 2010. As of 2017, a total of 650 stations have been deployed and configured. The NTU system can provide earthquake information within 15 s of an earthquake occurrence. Thus, this system may provide early warnings for cities located more than 50 km from the epicenter. Additionally, the NTU system also has an onsite alert function that triggers a warning for incoming P-waves greater than a certain magnitude threshold, thus providing a 2-3 s lead time before peak ground acceleration (PGA) for regions close to an epicenter. Detailed shaking maps are produced by the NTU system within one or two minutes after an earthquake. Recently, a new module named ShakeAlarm has been developed. Equipped with real-time acceleration signals and the time-dependent anisotropic attenuation relationship of the PGA, ShakingAlarm can provide an accurate PGA estimation immediately before the arrival of the observed PGA. This unique advantage produces sufficient lead time for hazard assessment and emergency response, which is unavailable for traditional shakemap, which are based on only the PGA observed in real time. The performance of ShakingAlarm was tested with six M > 5.5 inland earthquakes from 2013 to 2016. Taking the 2016 M6.4 Meinong earthquake simulation as an example, the predicted PGA converges to a stable value and produces a predicted shake map and an isocontour map of the predicted PGA within 16 seconds of earthquake occurrence. Compared with traditional regional EEW system, ShakingAlarm can effectively identify possible damage regions and provide valuable early warning information (magnitude and PGA) for risk mitigation.

A Comparison of Educational "Value-Added" Methodologies for Classifying Teacher Effectiveness: Value Tables vs. Covariate Regression

ERIC Educational Resources Information Center

Dwyer, Theodore J.

2016-01-01

There is a great deal of concern regarding teacher impacts on student achievement being used as a substantial portion of a teacher's performance evaluation. This study investigated the degree of concordance and discordance between mathematics teacher ranking using value tables and covariate regression, which have both been used as measures for…

An Alternative Teaching Method of Conditional Probabilities and Bayes' Rule: An Application of the Truth Table

ERIC Educational Resources Information Center

Satake, Eiki; Vashlishan Murray, Amy

2015-01-01

This paper presents a comparison of three approaches to the teaching of probability to demonstrate how the truth table of elementary mathematical logic can be used to teach the calculations of conditional probabilities. Students are typically introduced to the topic of conditional probabilities--especially the ones that involve Bayes' rule--with…

Effects of oxcarbazepine on monoamines content in hippocampus and head and body shakes and sleep patterns in kainic acid-treated rats.

PubMed

Alfaro-Rodríguez, Alfonso; González-Piña, Rigoberto; Bueno-Nava, Antonio; Arch-Tirado, Emilio; Ávila-Luna, Alberto; Uribe-Escamilla, Rebeca; Vargas-Sánchez, Javier

2011-09-01

The aim of this work was to analyze the effect of oxcarbazepine (OXC) on sleep patterns, "head and body shakes" and monoamine neurotransmitters level in a model of kainic-induced seizures. Adult Wistar rats were administered kainic acid (KA), OXC or OXC + KA. A polysomnographic study showed that KA induced animals to stay awake for the whole initial 10 h. OXC administration 30 min prior to KA diminished the effect of KA on the sleep parameters. As a measure of the effects of the drug treatments on behavior, head and body shakes were visually recorded for 4 h after administration of KA, OXC + KA or saline. The presence of OXC diminished the shakes frequency. 4 h after drug application, the hippocampus was dissected out, and the content of monoamines was analyzed. The presence of OXC still more increased serotonin, 5-hidroxyindole acetic acid, dopamine, and homovanilic acid, induced by KA.

Correlation between shaking behaviors and seizure severity in five animal models of convulsive seizures.

PubMed

Rodrigues, Marcelo Cairrão Araújo; Rossetti, Franco; Foresti, Maira Licia; Arisi, Gabriel Maisonnave; Furtado, Márcio Araújo; Dal-Cól, Maria Luiza Cleto; Bertti, Poliana; Fernandes, Artur; Santos, Francisco Leite; Del Vecchio, Flávio; Garcia-Cairasco, Norberto

2005-05-01

Wet dog shakes (WDS) and head shakes (HS) are associated with experimentally induced convulsive seizures. We sought to determine whether these behaviors are correlated or not with major (status epilepticus (SE) or fully kindled animals) or minor (non-SE or partially kindled animals) seizure severity. WDS are directly correlated with SE induced by intracerebral star fruit extract (Averrhoa carambola) injection and with kindled animals in the amygdala fast kindling model. On the other hand, WDS are inversely correlated with SE induced by intracerebral bicuculline and pilocarpine injections. Systemic pilocarpine in animals pretreated with methyl-scopolamine barely induced WDS or HS. The role of shaking behaviors may vary from ictal to anticonvulsant depending on the experimental seizure model, circuitries involved, and stimulus intensity. The physical presence of acrylic helmets may per se inhibit the HS response. Also, methyl-scopolamine, a drug incapable of crossing the blood-brain barrier, can induce HS in animals without acrylic helmets.

CyberShake: Running Seismic Hazard Workflows on Distributed HPC Resources

NASA Astrophysics Data System (ADS)

Callaghan, S.; Maechling, P. J.; Graves, R. W.; Gill, D.; Olsen, K. B.; Milner, K. R.; Yu, J.; Jordan, T. H.

2013-12-01

As part of its program of earthquake system science research, the Southern California Earthquake Center (SCEC) has developed a simulation platform, CyberShake, to perform physics-based probabilistic seismic hazard analysis (PSHA) using 3D deterministic wave propagation simulations. CyberShake performs PSHA by simulating a tensor-valued wavefield of Strain Green Tensors, and then using seismic reciprocity to calculate synthetic seismograms for about 415,000 events per site of interest. These seismograms are processed to compute ground motion intensity measures, which are then combined with probabilities from an earthquake rupture forecast to produce a site-specific hazard curve. Seismic hazard curves for hundreds of sites in a region can be used to calculate a seismic hazard map, representing the seismic hazard for a region. We present a recently completed PHSA study in which we calculated four CyberShake seismic hazard maps for the Southern California area to compare how CyberShake hazard results are affected by different SGT computational codes (AWP-ODC and AWP-RWG) and different community velocity models (Community Velocity Model - SCEC (CVM-S4) v11.11 and Community Velocity Model - Harvard (CVM-H) v11.9). We present our approach to running workflow applications on distributed HPC resources, including systems without support for remote job submission. We show how our approach extends the benefits of scientific workflows, such as job and data management, to large-scale applications on Track 1 and Leadership class open-science HPC resources. We used our distributed workflow approach to perform CyberShake Study 13.4 on two new NSF open-science HPC computing resources, Blue Waters and Stampede, executing over 470 million tasks to calculate physics-based hazard curves for 286 locations in the Southern California region. For each location, we calculated seismic hazard curves with two different community velocity models and two different SGT codes, resulting in over 1100 hazard curves. We will report on the performance of this CyberShake study, four times larger than previous studies. Additionally, we will examine the challenges we face applying these workflow techniques to additional open-science HPC systems and discuss whether our workflow solutions continue to provide value to our large-scale PSHA calculations.

The ShakeMap Atlas for the City of Naples, Italy

NASA Astrophysics Data System (ADS)

Pierdominici, Simona; Faenza, Licia; Camassi, Romano; Michelini, Alberto; Ercolani, Emanuela; Lauciani, Valentino

2016-04-01

Naples is one of the most vulnerable cities in the world because it is threatened by several natural and man-made hazards: earthquakes, volcanic eruptions, tsunamis, landslides, hydrogeological disasters, and morphologic alterations due to human interference. In addition, the risk is increased by the high density of population (Naples and the surrounding area are among the most populated in Italy), and by the type and condition of buildings and monuments. In light of this, it is crucial to assess the ground shaking suffered by the city. We take into account and integrate data information from five Italian databases and catalogues (DBMI11; CPTI11; CAMAL11; MOLAL08; ITACA) to build a reliable ShakeMap atlas for the area and to recreate the seismic history of the city from historical to recent times (1293 to 1999). This large amount of data gives the opportunity to explore several sources of information, expanding the completeness of our data set in both time and magnitude. 84 earthquakes have been analyzed and for each event, a Shakemap set has been computed using an ad hoc implementation developed for this application: (1) specific ground-motion prediction equations (GMPEs) accounting for the different attenuation properties in volcanic areas compared with the tectonic ones, and (2) detailed local microzonation to include the site effects. The ShakeMap atlas has two main applications: a) it is an important instrument in seismic risk management. It quantifies the level of shaking suffered by a city during its history, and it could be implemented to the quantification of the number of people exposed to certain degrees of shaking. Intensity data provide the evaluation of the damage caused by earthquakes; the damage is closely linked with the ground shaking, building type, and vulnerability, and it is not possible to separate these contributions; b) the Atlas can be used as starting point for Bayesian estimation of seismic hazard. This technique allows for the merging of the more standard approach adopted in the compilation of the national hazard map of Italy. These Shakemaps are provided in terms of Mercalli-Cancani-Sieberg intensity (MCS hereinafter) and peak ground acceleration (PGA).

Experimental determination of the x-ray atomic fundamental parameters of nickel

NASA Astrophysics Data System (ADS)

Ménesguen, Y.; Lépy, M.-C.; Hönicke, P.; Müller, M.; Unterumsberger, R.; Beckhoff, B.; Hoszowska, J.; Dousse, J.-Cl; Błachucki, W.; Ito, Y.; Yamashita, M.; Fukushima, S.

2018-02-01

The x-ray atomic properties of nickel (Ni) were investigated in a unique approach combining different experimental techniques to obtain new, useful and reliable values of atomic fundamental parameters for x-ray spectrometric purposes and for comparison with theoretical predictions. We determined the mass attenuation coefficients in an energy range covering the L- and K-absorption edges, the K-shell fluorescence yield and the Kβ/Kα and Kβ1, 3/Kα1, 2 transition probability ratios. The obtained line profiles and linewidths of the Kα and Kβ transitions in Ni can be considered as the contribution of the satellite lines arising from the [KM] shake processes suggested by Deutsch et al (1995 Phys. Rev. A 51 283) and Ito et al (2016 Phys. Rev. A 94 042506). Comparison of the new data with several databases showed good agreement, but also discrepancies were found with existing tabulated values.

Managing large-scale workflow execution from resource provisioning to provenance tracking: The CyberShake example

USGS Publications Warehouse

Deelman, E.; Callaghan, S.; Field, E.; Francoeur, H.; Graves, R.; Gupta, N.; Gupta, V.; Jordan, T.H.; Kesselman, C.; Maechling, P.; Mehringer, J.; Mehta, G.; Okaya, D.; Vahi, K.; Zhao, L.

2006-01-01

This paper discusses the process of building an environment where large-scale, complex, scientific analysis can be scheduled onto a heterogeneous collection of computational and storage resources. The example application is the Southern California Earthquake Center (SCEC) CyberShake project, an analysis designed to compute probabilistic seismic hazard curves for sites in the Los Angeles area. We explain which software tools were used to build to the system, describe their functionality and interactions. We show the results of running the CyberShake analysis that included over 250,000 jobs using resources available through SCEC and the TeraGrid. ?? 2006 IEEE.

The Quake-Catcher Network: Improving Earthquake Strong Motion Observations Through Community Engagement

NASA Astrophysics Data System (ADS)

Cochran, E. S.; Lawrence, J. F.; Christensen, C. M.; Chung, A. I.; Neighbors, C.; Saltzman, J.

2010-12-01

The Quake-Catcher Network (QCN) involves the community in strong motion data collection by utilizing volunteer computing techniques and low-cost MEMS accelerometers. Volunteer computing provides a mechanism to expand strong-motion seismology with minimal infrastructure costs, while promoting community participation in science. Micro-Electro-Mechanical Systems (MEMS) triaxial accelerometers can be attached to a desktop computer via USB and are internal to many laptops. Preliminary shake table tests show the MEMS accelerometers can record high-quality seismic data with instrument response similar to research-grade strong-motion sensors. QCN began distributing sensors and software to K-12 schools and the general public in April 2008 and has grown to roughly 1500 stations worldwide. We also recently tested whether sensors could be quickly deployed as part of a Rapid Aftershock Mobilization Program (RAMP) following the 2010 M8.8 Maule, Chile earthquake. Volunteers are recruited through media reports, web-based sensor request forms, as well as social networking sites. Using data collected to date, we examine whether a distributed sensing network can provide valuable seismic data for earthquake detection and characterization while promoting community participation in earthquake science. We utilize client-side triggering algorithms to determine when significant ground shaking occurs and this metadata is sent to the main QCN server. On average, trigger metadata are received within 1-10 seconds from the observation of a trigger; the larger data latencies are correlated with greater server-station distances. When triggers are detected, we determine if the triggers correlate to others in the network using spatial and temporal clustering of incoming trigger information. If a minimum number of triggers are detected then a QCN-event is declared and an initial earthquake location and magnitude is estimated. Initial analysis suggests that the estimated locations and magnitudes are similar to those reported in regional and global catalogs. As the network expands, it will become increasingly important to provide volunteers access to the data they collect, both to encourage continued participation in the network and to improve community engagement in scientific discourse related to seismic hazard. In the future, we hope to provide access to both images and raw data from seismograms in formats accessible to the general public through existing seismic data archives (e.g. IRIS, SCSN) and/or through the QCN project website. While encouraging community participation in seismic data collection, we can extend the capabilities of existing seismic networks to rapidly detect and characterize strong motion events. In addition, the dense waveform observations may provide high-resolution ground shaking information to improve source imaging and seismic risk assessment.

The ShakeOut Earthquake Scenario - A Story That Southern Californians Are Writing

USGS Publications Warehouse

Perry, Suzanne; Cox, Dale; Jones, Lucile; Bernknopf, Richard; Goltz, James; Hudnut, Kenneth; Mileti, Dennis; Ponti, Daniel; Porter, Keith; Reichle, Michael; Seligson, Hope; Shoaf, Kimberley; Treiman, Jerry; Wein, Anne

2008-01-01

The question is not if but when southern California will be hit by a major earthquake - one so damaging that it will permanently change lives and livelihoods in the region. How severe the changes will be depends on the actions that individuals, schools, businesses, organizations, communities, and governments take to get ready. To help prepare for this event, scientists of the U.S. Geological Survey (USGS) have changed the way that earthquake scenarios are done, uniting a multidisciplinary team that spans an unprecedented number of specialties. The team includes the California Geological Survey, Southern California Earthquake Center, and nearly 200 other partners in government, academia, emergency response, and industry, working to understand the long-term impacts of an enormous earthquake on the complicated social and economic interactions that sustain southern California society. This project, the ShakeOut Scenario, has applied the best current scientific understanding to identify what can be done now to avoid an earthquake catastrophe. More information on the science behind this project will be available in The ShakeOut Scenario (USGS Open-File Report 2008-1150; http://pubs.usgs.gov/of/2008/1150/). The 'what if?' earthquake modeled in the ShakeOut Scenario is a magnitude 7.8 on the southern San Andreas Fault. Geologists selected the details of this hypothetical earthquake by considering the amount of stored strain on that part of the fault with the greatest risk of imminent rupture. From this, seismologists and computer scientists modeled the ground shaking that would occur in this earthquake. Engineers and other professionals used the shaking to produce a realistic picture of this earthquake's damage to buildings, roads, pipelines, and other infrastructure. From these damages, social scientists projected casualties, emergency response, and the impact of the scenario earthquake on southern California's economy and society. The earthquake, its damages, and resulting losses are one realistic outcome, deliberately not a worst-case scenario, rather one worth preparing for and mitigating against. Decades of improving the life-safety requirements in building codes have greatly reduced the risk of death in earthquakes, yet southern California's economic and social systems are still vulnerable to large-scale disruptions. Because of this, the ShakeOut Scenario earthquake would dramatically alter the nature of the southern California community. Fortunately, steps can be taken now that can change that outcome and repay any costs many times over. The ShakeOut Scenario is the first public product of the USGS Multi-Hazards Demonstration Project, created to show how hazards science can increase a community's resiliency to natural disasters through improved planning, mitigation, and response.

The Early Warning System(EWS) as First Stage to Generate and Develop Shake Map for Bucharest to Deep Vrancea Earthquakes

NASA Astrophysics Data System (ADS)

Marmureanu, G.; Ionescu, C.; Marmureanu, A.; Grecu, B.; Cioflan, C.

2007-12-01

EWS made by NIEP is the first European system for real-time early detection and warning of the seismic waves in case of strong deep earthquakes. EWS uses the time interval (28-32 seconds) between the moment when earthquake is detected by the borehole and surface local accelerometers network installed in the epicenter area (Vrancea) and the arrival time of the seismic waves in the protected area, to deliver timely integrated information in order to enable actions to be taken before a main destructive shaking takes place. Early warning system is viewed as part of an real-time information system that provide rapid information, about an earthquake impeding hazard, to the public and disaster relief organizations before (early warning) and after a strong earthquake (shake map).This product is fitting in with other new product on way of National Institute for Earth Physics, that is, the shake map which is a representation of ground shaking produced by an event and it will be generated automatically following large Vrancea earthquakes. Bucharest City is located in the central part of the Moesian platform (age: Precambrian and Paleozoic) in the Romanian Plain, at about 140 km far from Vrancea area. Above a Cretaceous and a Miocene deposit (with the bottom at roundly 1,400 m of depth), a Pliocene shallow water deposit (~ 700m thick) was settled. The surface geology consists mainly of Quaternary alluvial deposits. Later loess covered these deposits and the two rivers crossing the city (Dambovita and Colentina) carved the present landscape. During the last century Bucharest suffered heavy damage and casualties due to 1940 (Mw = 7.7) and 1977 (Mw = 7.4) Vrancea earthquakes. For example, 32 high tall buildings collapsed and more then 1500 people died during the 1977 event. The innovation with comparable or related systems worldwide is that NIEP will use the EWS to generate a virtual shake map for Bucharest (140 km away of epicentre) immediately after the magnitude is estimated (in 3-4 seconds after the detection in epicentre) and later make corrections by using real time dataflow from each K2 accelerometers installed in Bucharest area, inclusively nonlinear effects. Thus, developing of a near real-time shake map for Bucharest urban area is of highest interest, providing valuable information to the civil defense, decision makers and general public on the area where the ground motion is most severe. EWS made by NIEP can be considered the first stage to generate and develop the shake map for Bucharest to deep Vrancea earthquakes.

The Long-term Impacts of Earthquakes on Economic Growth

NASA Astrophysics Data System (ADS)

Lackner, S.

2016-12-01

The social science literature has so far not reached a consensus on whether and how earthquakes actually impact economic growth in the long-run. Several hypotheses have been suggested and some even argue for a positive impact. A general weakness in the literature, however, is the predominant use of inadequate measures for the exogenous natural hazard of an earthquake. The most common problems are the lack of individual event size (e.g. earthquake dummy or number of events), the use of magnitude instead of a measure for surface shaking, and endogeneity issues when traditional qualitative intensity scales or actual impact data is used. Here we use peak ground acceleration (PGA) as the ground motion intensity measure and investigate the impacts of earthquake shaking on long-run economic growth. We construct a data set from USGS ShakeMaps that can be considered the universe of global relevant earthquake ground shaking from 1973 to 2014. This data set is then combined with World Bank GDP data to conduct a regression analysis. Furthermore, the impacts of PGA on different industries and other economic variables such as employment and education are also investigated. This will on one hand help to identify the mechanism of how earthquakes impact long-run growth and also show potential impacts on other welfare indicators that are not captured by GDP. This is the first application of global earthquake shaking data to investigate long-term earthquake impacts.

On-line prediction of the glucose concentration of CHO cell cultivations by NIR and Raman spectroscopy: Comparative scalability test with a shake flask model system.

PubMed

Kozma, Bence; Hirsch, Edit; Gergely, Szilveszter; Párta, László; Pataki, Hajnalka; Salgó, András

2017-10-25

In this study, near-infrared (NIR) and Raman spectroscopy were compared in parallel to predict the glucose concentration of Chinese hamster ovary cell cultivations. A shake flask model system was used to quickly generate spectra similar to bioreactor cultivations therefore accelerating the development of a working model prior to actual cultivations. Automated variable selection and several pre-processing methods were tested iteratively during model development using spectra from six shake flask cultivations. The target was to achieve the lowest error of prediction for the glucose concentration in two independent shake flasks. The best model was then used to test the scalability of the two techniques by predicting spectra of a 10l and a 100l scale bioreactor cultivation. The NIR spectroscopy based model could follow the trend of the glucose concentration but it was not sufficiently accurate for bioreactor monitoring. On the other hand, the Raman spectroscopy based model predicted the concentration of glucose in both cultivation scales sufficiently accurately with an error around 4mM (0.72g/l), that is satisfactory for the on-line bioreactor monitoring purposes of the biopharma industry. Therefore, the shake flask model system was proven to be suitable for scalable spectroscopic model development. Copyright © 2017 Elsevier B.V. All rights reserved.

Quantitative x-ray photoelectron spectroscopy: Quadrupole effects, shake-up, Shirley background, and relative sensitivity factors from a database of true x-ray photoelectron spectra

NASA Astrophysics Data System (ADS)

Seah, M. P.; Gilmore, I. S.

2006-05-01

An analysis is provided of the x-ray photoelectron spectroscopy (XPS) intensities measured in the National Physical Laboratory (NPL) XPS database for 46 solid elements. This present analysis does not change our previous conclusions concerning the excellent correlation between experimental intensities, following deconvolving the spectra with angle-averaged reflection electron energy loss data, and the theoretical intensities involving the dipole approximation using Scofield’s cross sections. Here, more recent calculations for cross sections by Trzhaskovskaya involving quadrupole terms are evaluated and it is shown that their cross sections diverge from the experimental database results by up to a factor of 5. The quadrupole angular terms lead to small corrections that are close to our measurement limit but do appear to be supported in the present analysis. Measurements of the extent of shake-up for the 46 elements broadly agree with the calculations of Yarzhemsky but not in detail. The predicted constancy in the shake-up contribution by Yarzhemsky implies that the use of the Shirley background will lead to a peak area that is a constant fraction of the true peak area including the shake-up intensities. However, the measured variability of the shake-up contribution makes the Shirley background invalid for quantification except for situations where the sensitivity factors are from reference samples similar to those being analyzed.

A Detailed Comparison of Maxicalculators. Illinois Series on Educational Applications of Computers. Number 6.

ERIC Educational Resources Information Center

Doring, Richard; Hicks, Bruce

A comparison is made of four maxicalculators and two minicomputers with an emphasis on two, the HP 9830 and the Wang 2200. Comparisons are in the form of a table with individual guidelines for analysis followed by the specific characteristics of the particular calculator. Features compared include: manual input facilities, screen, secondary…

Comparing Performances of Multiple Comparison Methods in Commonly Used 2 × C Contingency Tables.

PubMed

Cangur, Sengul; Ankarali, Handan; Pasin, Ozge

2016-12-01

This study aims at mentioning briefly multiple comparison methods such as Bonferroni, Holm-Bonferroni, Hochberg, Hommel, Marascuilo, Tukey, Benjamini-Hochberg and Gavrilov-Benjamini-Sarkar for contingency tables, through the data obtained from a medical research and examining their performances by simulation study which was constructed as the total 36 scenarios to 2 × 4 contingency table. As results of simulation, it was observed that when the sample size is more than 100, the methods which can preserve the nominal alpha level are Gavrilov-Benjamini-Sarkar, Holm-Bonferroni and Bonferroni. Marascuilo method was found to be a more conservative than Bonferroni. It was found that Type I error rate for Hommel method is around 2 % in all scenarios. Moreover, when the proportions of the three populations are equal and the proportion value of the fourth population is far at a level of ±3 standard deviation from the other populations, the power value for Unadjusted All-Pairwise Comparison approach is at least a bit higher than the ones obtained by Gavrilov-Benjamini-Sarkar, Holm-Bonferroni and Bonferroni. Consequently, Gavrilov-Benjamini-Sarkar and Holm-Bonferroni methods have the best performance according to simulation. Hommel and Marascuilo methods are not recommended to be used because they have medium or lower performance. In addition, we have written a Minitab macro about multiple comparisons for use in scientific research.

USGS earthquake hazards program (EHP) GPS use case : earthquake early warning (EEW) and shake alert

DOT National Transportation Integrated Search

2017-03-30

GPS Adjacent Band Workshop VI RTCA Inc., Washington D.C., 30 March 2017. USGS GPS receiver use case - Real-Time GPS for EEW -Continued: CRITICAL EFFECT - The GNSS component of the Shake Alert system augments the inertial sensors and is especial...

Tests of Independence in Contingency Tables with Small Samples: A Comparison of Statistical Power.

ERIC Educational Resources Information Center

Parshall, Cynthia G.; Kromrey, Jeffrey D.

1996-01-01

Power and Type I error rates were estimated for contingency tables with small sample sizes for the following four types of tests: (1) Pearson's chi-square; (2) chi-square with Yates's continuity correction; (3) the likelihood ratio test; and (4) Fisher's Exact Test. Various marginal distributions, sample sizes, and effect sizes were examined. (SLD)

Comparison of Original and Revised Student Financial Aid Estimates for 2007-08. Web Tables. NCES 2014-179

ERIC Educational Resources Information Center

Shaw, Stacy; Radwin, David

2014-01-01

The web tables in this report provide original and revised estimates of statistics previously published in 2007-08 National Postsecondary Student Aid Study (NPSAS:08): Student Financial Aid Estimates for 2007-08 (NCES 2009-166). The revised estimates were generated using revised weights that were updated in August 2013. NPSAS:08 data were…

Summary of Computer Usage and Inventory of Computer Utilization in Curriculum, FY 1988-89.

ERIC Educational Resources Information Center

Tennessee Univ., Chattanooga. Center of Excellence for Computer Applications.

In addition to data on FY 1988-89, the 12 tables that constitute the major part of this report on computer utilization at the University of Tennessee at Chattanooga (UTC) provide comparisons among the 10 annual inventories that have been conducted, and demonstrate growth patterns over the 10-year period. The first five tables organize data by…

Turtlegraphics: A Comparison of Logo and Turbo Pascal.

ERIC Educational Resources Information Center

VanLengen, Craig A.

1989-01-01

The integrated compiler of the Turbo Pascal environment allows the execution of a completed program independent of the developed environment and with greater execution speed, in comparison with LOGO. Conversion table of turtle-graphic commands for the two languages is presented. (Author/YP)

VizieR Online Data Catalog: Field RR Lyrae stars (Liska+, 2016)

NASA Astrophysics Data System (ADS)

Liska, J.; Skarka, M.; Zejda, M.; Mikulasek, Z.; de Villiers, S. N.

2016-05-01

Differential photometry for VX Her in 'table1.dat' file. New photometric measurements for VX Her were performed at Masaryk University Observatory, Brno, Czech Republic during 13 nights (April-August 2014) with 0.6-m (24-inch) Newtonian telescope, CCD G2-0402, in BVRI bands. CCD images were calibrated in a standard way (dark frame and flat field corrections). The C-Munipack software (Motl 2009) was used for this processing as well as for differential photometry. TYC 1510-269-1 and TYC 1510-149-1 were used as comparison and check stars, respectively. Differential photometry for AT Ser and SS Leo is in 'table2.dat' file. New photometric measurements for these two stars were obtained using 1-inch refractor (a photographic lens Sonnar 4/135mm, lens focal ratio/focal length) and ATIK 16IC CCD camera with green photometric filter with similar throughput as the Johnson V filter. Exposures were 30s and each five frames were combined to a single image to achieve a better signal-to-noise ratio. The time resolution of a such combined frame is about 170s. The comparison stars were HD 142799 for AT Ser and HD 100763 for SS Leo. List with candidates for binaries with RR Lyrae component - RRLyrBinCan database (version 2016 May 5) is in 'table3.dat' file. 'table4.dat' file contains false-positives binary candidates among RR Lyrae stars. 'table5.dat' and 'table6.dat' files contain used maxima timings given in GEOS RR Lyr database, or newly determined in this study. (7 data files).

Automatic Hidden-Web Table Interpretation by Sibling Page Comparison

NASA Astrophysics Data System (ADS)

Tao, Cui; Embley, David W.

The longstanding problem of automatic table interpretation still illudes us. Its solution would not only be an aid to table processing applications such as large volume table conversion, but would also be an aid in solving related problems such as information extraction and semi-structured data management. In this paper, we offer a conceptual modeling solution for the common special case in which so-called sibling pages are available. The sibling pages we consider are pages on the hidden web, commonly generated from underlying databases. We compare them to identify and connect nonvarying components (category labels) and varying components (data values). We tested our solution using more than 2,000 tables in source pages from three different domains—car advertisements, molecular biology, and geopolitical information. Experimental results show that the system can successfully identify sibling tables, generate structure patterns, interpret tables using the generated patterns, and automatically adjust the structure patterns, if necessary, as it processes a sequence of hidden-web pages. For these activities, the system was able to achieve an overall F-measure of 94.5%.

Dynamics of the McDonnell Douglas Large Scale Dynamic Rig and Dynamic Calibration of the Rotor Balance

DOT National Transportation Integrated Search

1994-10-01

A shake test was performed on the Large Scale Dynamic Rig in the 40- by 80-Foot Wind Tunnel in support of the McDonnell Douglas Advanced Rotor Technology (MDART) Test Program. The shake test identifies the hub modes and the dynamic calibration matrix...

Shaking up Expectations: The OCLS Shake It! App

ERIC Educational Resources Information Center

Shivers, Cassandra

2012-01-01

The author, a digital access architect in the information systems department of the Orange County Library System in Florida, was given the challenge of creating a library mobile app around the 2009 holiday season. At that time, Sheri Chambers, digital content manager in the information systems department, and Debbie Moss, assistant director of the…

PHYSICAL AND BIOLOGICAL PARAMETERS THAT DETERMINE THE FATE OF 'P'-CHLOROPHENOL IN LABORATORY TEST SYSTEMS

EPA Science Inventory

Shake flask and microcosm studies were conducted to determine the fate of parachlorophenol (p-CP) in water and sediment systems and the role of sediment and nonsediment surfaces in the biodegradation process. Biodegradation of p-CP in estuarine water samples in shake flasks was s...

Shaking the Tree, Making a Rhizome: Towards a Nomadic Geophilosophy of Science Education

ERIC Educational Resources Information Center

Gough, Noel

2006-01-01

This essay enacts a philosophy of science education inspired by Gilles Deleuze and Felix Guattari's figurations of rhizomatic and nomadic thought. It imagines rhizomes shaking the tree of modern Western science and science education by destabilising arborescent conceptions of knowledge as hierarchically articulated branches of a central stem or…

Beside the point: Mothers' head nodding and shaking gestures during parent-child play.

PubMed

Fusaro, Maria; Vallotton, Claire D; Harris, Paul L

2014-05-01

Understanding the context for children's social learning and language acquisition requires consideration of caregivers' multi-modal (speech, gesture) messages. Though young children can interpret both manual and head gestures, little research has examined the communicative input that children receive via parents' head gestures. We longitudinally examined the frequency and communicative functions of mothers' head nodding and head shaking gestures during laboratory play sessions for 32 mother-child dyads, when the children were 14, 20, and 30 months of age. The majority of mothers produced head nods more frequently than head shakes. Both gestures contributed to mothers' verbal attempts at behavior regulation and dialog. Mothers' head nods primarily conveyed agreement with, and attentiveness to, children's utterances, and accompanied affirmative statements and yes/no questions. Mothers' head shakes primarily conveyed prohibitions and statements with negations. Changes over time appeared to reflect corresponding developmental changes in social and communicative dimensions of caregiver-child interaction. Directions for future research are discussed regarding the role of head gesture input in socialization and in supporting language development. Copyright © 2014 Elsevier Inc. All rights reserved.

MyShake - A smartphone app to detect earthquake

NASA Astrophysics Data System (ADS)

Kong, Q.; Allen, R. M.; Schreier, L.; Kwon, Y. W.

2015-12-01

We designed an android app that harnesses the accelerometers in personal smartphones to record earthquake-shaking data for research, hazard information and warnings. The app has the function to distinguish earthquake shakings from daily human activities based on the different patterns behind the movements. It also can be triggered by the traditional earthquake early warning (EEW) system to record for a certain amount of time to collect earthquake data. When the app is triggered by the earthquake-like movements, it sends the trigger information back to our server which contains time and location of the trigger, at the same time, it stores the waveform data on local phone first, and upload to our server later. Trigger information from multiple phones will be processed in real time on the server to find the coherent signal to confirm the earthquakes. Therefore, the app provides the basis to form a smartphone seismic network that can detect earthquake and even provide warnings. A planned public roll-out of MyShake could collect millions of seismic recordings for large earthquakes in many regions around the world.

Combining multiple earthquake models in real time for earthquake early warning

USGS Publications Warehouse

Minson, Sarah E.; Wu, Stephen; Beck, James L; Heaton, Thomas H.

2017-01-01

The ultimate goal of earthquake early warning (EEW) is to provide local shaking information to users before the strong shaking from an earthquake reaches their location. This is accomplished by operating one or more real‐time analyses that attempt to predict shaking intensity, often by estimating the earthquake’s location and magnitude and then predicting the ground motion from that point source. Other EEW algorithms use finite rupture models or may directly estimate ground motion without first solving for an earthquake source. EEW performance could be improved if the information from these diverse and independent prediction models could be combined into one unified, ground‐motion prediction. In this article, we set the forecast shaking at each location as the common ground to combine all these predictions and introduce a Bayesian approach to creating better ground‐motion predictions. We also describe how this methodology could be used to build a new generation of EEW systems that provide optimal decisions customized for each user based on the user’s individual false‐alarm tolerance and the time necessary for that user to react.

Bucket shaking stops bunch dancing in Tevatron

DOE Office of Scientific and Technical Information (OSTI.GOV)

Burov, A.; Tan, C.Y.; /Fermilab

2011-03-01

Bunches in Tevatron are known to be longitudinally unstable: their collective oscillations, also called dancing bunches, persist without any signs of decay. Typically, a damper is used to stop these oscillations, but recently, it was theoretically predicted that the oscillations can be stabilized by means of small bucket shaking. Dedicated measurements in Tevatron have shown that this method does stop the dancing. According to predictions of Refs. [2,3], the flattening of the bunch distribution at low amplitudes should make the bunch more stable against LLD. An experiment has been devised to flatten the distribution by modulating the RF phase atmore » the low-amplitude synchrotron frequency for a few degrees of amplitude. These beam studies show that stabilisation really happens. After several consecutive shakings, the dancing disappears and the resulting bunch profile becomes smoother at the top. Although not shown in this report, sometimes a little divot forms at the centre of the distribution. These experiments confirm that resonant RF shaking flattens the bunch distribution at low amplitudes, and the dancing stops.« less

Real-time 3-D space numerical shake prediction for earthquake early warning

NASA Astrophysics Data System (ADS)

Wang, Tianyun; Jin, Xing; Huang, Yandan; Wei, Yongxiang

2017-12-01

In earthquake early warning systems, real-time shake prediction through wave propagation simulation is a promising approach. Compared with traditional methods, it does not suffer from the inaccurate estimation of source parameters. For computation efficiency, wave direction is assumed to propagate on the 2-D surface of the earth in these methods. In fact, since the seismic wave propagates in the 3-D sphere of the earth, the 2-D space modeling of wave direction results in inaccurate wave estimation. In this paper, we propose a 3-D space numerical shake prediction method, which simulates the wave propagation in 3-D space using radiative transfer theory, and incorporate data assimilation technique to estimate the distribution of wave energy. 2011 Tohoku earthquake is studied as an example to show the validity of the proposed model. 2-D space model and 3-D space model are compared in this article, and the prediction results show that numerical shake prediction based on 3-D space model can estimate the real-time ground motion precisely, and overprediction is alleviated when using 3-D space model.

Abusive head trauma and the triad: a critique on behalf of RCPCH of 'Traumatic shaking: the role of the triad in medical investigations of suspected traumatic shaking'.

PubMed

Debelle, Geoffrey David; Maguire, Sabine; Watts, Patrick; Nieto Hernandez, Rosa; Kemp, Alison Mary

2018-06-01

The Swedish Agency for Health Technology Assessment and Assessment of Social Services (SBU) has recently published what they purported to be a systematic review of the literature on 'isolated traumatic shaking' in infants, concluding that 'there is limited evidence that the so-called triad (encephalopathy, subdural haemorrhage, retinal haemorrhage) and therefore its components can be associated with traumatic shaking'. This flawed report, from a national body, demands a robust response. The conclusions of the original report have the potential to undermine medico-legal practice. We have conducted a critique of the methodology used in the SBU review and have found it to be flawed, to the extent that children's lives may be put at risk. Thus, we call on this review to be withdrawn or to be subjected to international scrutiny. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2018. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

St. Louis area earthquake hazards mapping project; seismic and liquefaction hazard maps

USGS Publications Warehouse

Cramer, Chris H.; Bauer, Robert A.; Chung, Jae-won; Rogers, David; Pierce, Larry; Voigt, Vicki; Mitchell, Brad; Gaunt, David; Williams, Robert; Hoffman, David; Hempen, Gregory L.; Steckel, Phyllis; Boyd, Oliver; Watkins, Connor M.; Tucker, Kathleen; McCallister, Natasha

2016-01-01

We present probabilistic and deterministic seismic and liquefaction hazard maps for the densely populated St. Louis metropolitan area that account for the expected effects of surficial geology on earthquake ground shaking. Hazard calculations were based on a map grid of 0.005°, or about every 500 m, and are thus higher in resolution than any earlier studies. To estimate ground motions at the surface of the model (e.g., site amplification), we used a new detailed near‐surface shear‐wave velocity model in a 1D equivalent‐linear response analysis. When compared with the 2014 U.S. Geological Survey (USGS) National Seismic Hazard Model, which uses a uniform firm‐rock‐site condition, the new probabilistic seismic‐hazard estimates document much more variability. Hazard levels for upland sites (consisting of bedrock and weathered bedrock overlain by loess‐covered till and drift deposits), show up to twice the ground‐motion values for peak ground acceleration (PGA), and similar ground‐motion values for 1.0 s spectral acceleration (SA). Probabilistic ground‐motion levels for lowland alluvial floodplain sites (generally the 20–40‐m‐thick modern Mississippi and Missouri River floodplain deposits overlying bedrock) exhibit up to twice the ground‐motion levels for PGA, and up to three times the ground‐motion levels for 1.0 s SA. Liquefaction probability curves were developed from available standard penetration test data assuming typical lowland and upland water table levels. A simplified liquefaction hazard map was created from the 5%‐in‐50‐year probabilistic ground‐shaking model. The liquefaction hazard ranges from low (60% of area expected to liquefy) in the lowlands. Because many transportation routes, power and gas transmission lines, and population centers exist in or on the highly susceptible lowland alluvium, these areas in the St. Louis region are at significant potential risk from seismically induced liquefaction and associated ground deformation

Using seismology to raise science awareness in kindergarten and elementary levels, with the help of high school students

NASA Astrophysics Data System (ADS)

Rocha, F. L.; Silveira, G. M.; Moreira, G.; Afonso, I. P.; Maciel, B. A. P. C.; Melo, M. O.; Neto, R. P.; Gonçalves, M.; Marques, G.; Hartmann, R. P.

2014-12-01

Teaching students, aged from 4 up to 18 years old, is a challenging task. It continuously implies new strategies and new subjects adapted to all of them. This is even more evident, when we have to teach natural-hazards scientific aspects and safe attitudes toward risk. We often see that most of the high-school students (16 -18 years old) are not motivated for extra-curricular activities implying science and/or behaviours changes. But, they have a very positive response when we give them some responsibility. On top of that, we also realised that young children are quite receptive to the involvement of older students in the school environment Taking this into consideration, our project use the k12 students to prepare scientific activities and subjects, based in questions, which they need to answer themselves. The students need to answer those questions and, only then, adapt and teach the right answers to the different school-levels. With this approach, we challenged the students to solve three questions: How to use a SEP seismometer at school, and its data? How to set up a shaking table? How to introduce waves and vibrations contents to all ages of students? During the project they developed many science skills, and worked in straight cooperation with teachers, the parents association and the seismology research group at Instituto Dom Luíz. As a result, it was possible to reach all school students with the help of the k-12 ones. This is an outcome of the project W-Shake, a Parents-in-Science Initiative to promote the study of seismology and related subjects. This project, supported by the Portuguese "Ciência Viva" program, results from a direct cooperation between the parents association, science school-teachers and the seismology research group at Instituto Dom Luíz.

Development of a Moodle Course for Schoolchildren's Table Tennis Learning Based on Competence Motivation Theory: Its Effectiveness in Comparison to Traditional Training Method

ERIC Educational Resources Information Center

Zou, Junhua; Liu, Qingtang; Yang, Zongkai

2012-01-01

Based on Competence Motivation Theory (CMT), a Moodle course for schoolchildren's table tennis learning was developed (The URL is http://www.bssepp.com, and this course allows guest access). The effects of the course on students' knowledge, perceived competence and interest were evaluated through quantitative methods. The sample of the study…

Merchantable height of trees in Oregon—a comparison of current logging practice and volume table specifications.

Treesearch

Don Minore; Donald R. Gedney

1960-01-01

A large proportion of present-day timber cruising is done by measuring or estimating three tree dimensions: diameter at breast height, form class, and merchantable height. Tree volumes are then determined from tables which equate volume to the varying combinations of height, d.b.h., and form class. Assumptions concerning merchantable height were made in constructing...

Plate-Impact Measurements of a Select Model Poly(urethane urea) Elastomer

DTIC Science & Technology

2013-06-01

experiments, and data for polyurea (dashed line) are also included for comparison. .....................................8 List of Tables Table 1...6 1 1. Introduction High-performance polyurea elastomers have recently gained considerable interest throughout the U.S. Department of...studies on high-strain-rate mechanical deformation and modeling (3, 6–11), wherein most are focused on a commercial polyurea . The commercial polyureas

Cost effectiveness of three different release treatments of table mountain pine in a severely overstocked and pure stand

Treesearch

Amy L. Morgan; Wayne K. Clatterbuck

2013-01-01

Table Mountain pine (Pinus pungens Lamb.) (TMP) is a threatened species, endemic to the Southern Appalachian Mountains. This study focuses on the release of TMP stems in an overstocked and pure TMP stand on the Cherokee National Forest in eastern Tennessee. The objective of the case study was to produce a cost analysis/comparison of releasing young...

Flow Regime Transition in Inner Grooved Minichannel Cold Plates for Cooling Hybrid Electric Power Electronics

DTIC Science & Technology

2013-01-01

reentrant cavities) Corrugated or fluted tubes Screens Inner grooved tubes ( microfin tubes ) Fins Electrohydrodynamic field effect 3.1 Convective... microfin geometries, including 3-D geometries, but most commercial vendors continue to manufacture seamless tubes (46). Figure 6a shows the...enhancement technologies are compiled in table 4. Table 4. Comparison of leading refrigeration tube performance (42). Metric Microfin Tube Twisted

High-speed shaking of frozen blood clots for extraction of human and malaria parasite DNA.

PubMed

Lundblom, Klara; Macharia, Alex; Lebbad, Marianne; Mohammed, Adan; Färnert, Anna

2011-08-08

Frozen blood clots remaining after serum collection is an often disregarded source of host and pathogen DNA due to troublesome handling and suboptimal outcome. High-speed shaking of clot samples in a cell disruptor manufactured for homogenization of tissue and faecal specimens was evaluated for processing frozen blood clots for DNA extraction. The method was compared to two commercial clot protocols based on a chemical kit and centrifugation through a plastic sieve, followed by the same DNA extraction protocol. Blood clots with different levels of parasitaemia (1-1,000 p/μl) were prepared from parasite cultures to assess sensitivity of PCR detection. In addition, clots retrieved from serum samples collected within two epidemiological studies in Kenya (n = 630) were processed by high speed shaking and analysed by PCR for detection of malaria parasites and the human α-thalassaemia gene. High speed shaking succeeded in fully dispersing the clots and the method generated the highest DNA yield. The level of PCR detection of P. falciparum parasites and the human thalassaemia gene was the same as samples optimally collected with an anticoagulant. The commercial clot protocol and centrifugation through a sieve failed to fully dissolve the clots and resulted in lower sensitivity of PCR detection. High speed shaking was a simple and efficacious method for homogenizing frozen blood clots before DNA purification and resulted in PCR templates of high quality both from humans and malaria parasites. This novel method enables genetic studies from stored blood clots.

MyShake: A smartphone seismic network for earthquake early warning and beyond

PubMed Central

Kong, Qingkai; Allen, Richard M.; Schreier, Louis; Kwon, Young-Woo

2016-01-01

Large magnitude earthquakes in urban environments continue to kill and injure tens to hundreds of thousands of people, inflicting lasting societal and economic disasters. Earthquake early warning (EEW) provides seconds to minutes of warning, allowing people to move to safe zones and automated slowdown and shutdown of transit and other machinery. The handful of EEW systems operating around the world use traditional seismic and geodetic networks that exist only in a few nations. Smartphones are much more prevalent than traditional networks and contain accelerometers that can also be used to detect earthquakes. We report on the development of a new type of seismic system, MyShake, that harnesses personal/private smartphone sensors to collect data and analyze earthquakes. We show that smartphones can record magnitude 5 earthquakes at distances of 10 km or less and develop an on-phone detection capability to separate earthquakes from other everyday shakes. Our proof-of-concept system then collects earthquake data at a central site where a network detection algorithm confirms that an earthquake is under way and estimates the location and magnitude in real time. This information can then be used to issue an alert of forthcoming ground shaking. MyShake could be used to enhance EEW in regions with traditional networks and could provide the only EEW capability in regions without. In addition, the seismic waveforms recorded could be used to deliver rapid microseism maps, study impacts on buildings, and possibly image shallow earth structure and earthquake rupture kinematics. PMID:26933682

MyShake: A smartphone seismic network for earthquake early warning and beyond.

PubMed

Kong, Qingkai; Allen, Richard M; Schreier, Louis; Kwon, Young-Woo

2016-02-01

Large magnitude earthquakes in urban environments continue to kill and injure tens to hundreds of thousands of people, inflicting lasting societal and economic disasters. Earthquake early warning (EEW) provides seconds to minutes of warning, allowing people to move to safe zones and automated slowdown and shutdown of transit and other machinery. The handful of EEW systems operating around the world use traditional seismic and geodetic networks that exist only in a few nations. Smartphones are much more prevalent than traditional networks and contain accelerometers that can also be used to detect earthquakes. We report on the development of a new type of seismic system, MyShake, that harnesses personal/private smartphone sensors to collect data and analyze earthquakes. We show that smartphones can record magnitude 5 earthquakes at distances of 10 km or less and develop an on-phone detection capability to separate earthquakes from other everyday shakes. Our proof-of-concept system then collects earthquake data at a central site where a network detection algorithm confirms that an earthquake is under way and estimates the location and magnitude in real time. This information can then be used to issue an alert of forthcoming ground shaking. MyShake could be used to enhance EEW in regions with traditional networks and could provide the only EEW capability in regions without. In addition, the seismic waveforms recorded could be used to deliver rapid microseism maps, study impacts on buildings, and possibly image shallow earth structure and earthquake rupture kinematics.

Evaluation of the shaking technique for the economic management of American foulbrood disease of honey bees (Hymenoptera: Apidae).

PubMed

Pernal, Stephen F; Albright, Robert L; Melathopoulos, Andony P

2008-08-01

Shaking is a nonantibiotic management technique for the bacterial disease American foulbrood (AFB) (Paenibacillus larvae sensu Genersch et al.), in which infected nesting comb is destroyed and the adult honey bees, Apis mellifera L. (Hymenoptera: Apidae), are transferred onto uncontaminated nesting material. We hypothesized that colonies shaken onto frames of uninfected drawn comb would have similar reductions in AFB symptoms and bacterial spore loads than those shaken onto frames of foundation, but they would attain higher levels of production. We observed that colonies shaken onto drawn comb, or a combination of foundation and drawn comb, exhibited light transitory AFB infections, whereas colonies shaken onto frames containing only foundation failed to exhibit clinical symptoms. Furthermore, concentrations of P. larvae spores in honey and adult worker bees sampled from colonies shaken onto all comb and foundation treatments declined over time and were undetectable in adult bee samples 3 mo after shaking. In contrast, colonies that were reestablished on the original infected comb remained heavily infected resulting in consistently high levels of spores, and eventually, their death. In a subsequent experiment, production of colonies shaken onto foundation was compared with that of colonies established from package (bulk) bees or that of overwintered colonies. Economic analysis proved shaking to be 24% more profitable than using package bees. These results suggest that shaking bees onto frames of foundation in the spring is a feasible option for managing AFB in commercial beekeeping operations where antibiotic use is undesirable or prohibited.

Effect of the consumption of a new symbiotic shake on glycemia and cholesterol levels in elderly people with type 2 diabetes mellitus

PubMed Central

2012-01-01

Background The consumption of foods containing probiotic and prebiotic ingredients is growing consistently every year, and in view of the limited number of studies investigating their effect in the elderly. Objective The objective of this study was to evaluate the effect of the consumption of a symbiotic shake containing Lactobacillus acidophilus, Bifidobacterium bifidum and fructooligosaccharides on glycemia and cholesterol levels in elderly people. Methods A randomized, double-blind, placebo-controlled study was conducted on twenty volunteers (ten for placebo group and ten for symbiotic group), aged 50 to 60 years. The criteria for inclusion in the study were: total cholesterol > 200 mg/dL; triglycerides > 200 mg/dL and glycemia > 110 mg/dL. Over a total test period of 30 days, 10 individuals (the symbiotic group) consumed a daily dose of 200 mL of a symbiotic shake containing 108 UFC/mL Lactobacillus acidophilus, 108 UFC/mL Bifidobacterium bifidum and 2 g oligofructose, while 10 other volunteers (the placebo group) drank daily the same amount of a shake that did not contain any symbiotic bacteria. Blood samples were collected 15 days prior to the start of the experiment and at 10-day intervals after the beginning of the shake intake. The standard lipid profile (total cholesterol, triglycerides and HDL cholesterol) and glycemia, or blood sugar levels, were evaluated by an enzyme colorimetric assay. Results The results of the symbiotic group showed a non-significant reduction (P > 0.05) in total cholesterol and triglycerides, a significant increase (P < 0.05) in HDL cholesterol and a significant reduction (P < 0.05) in fasting glycemia. No significant changes were observed in the placebo group. Conclusion The consumption of symbiotic shake resulted in a significant increase in HDL and a significant decrease of glycemia. Trial Registration ClinicalTrials.gov: NCT00123456 PMID:22356933

Effect of the consumption of a new symbiotic shake on glycemia and cholesterol levels in elderly people with type 2 diabetes mellitus.

PubMed

Moroti, Camila; Souza Magri, Loyanne Francine; de Rezende Costa, Marcela; Cavallini, Daniela C U; Sivieri, Katia

2012-02-22

The consumption of foods containing probiotic and prebiotic ingredients is growing consistently every year, and in view of the limited number of studies investigating their effect in the elderly. The objective of this study was to evaluate the effect of the consumption of a symbiotic shake containing Lactobacillus acidophilus, Bifidobacterium bifidum and fructooligosaccharides on glycemia and cholesterol levels in elderly people. A randomized, double-blind, placebo-controlled study was conducted on twenty volunteers (ten for placebo group and ten for symbiotic group), aged 50 to 60 years. The criteria for inclusion in the study were: total cholesterol > 200 mg/dL; triglycerides > 200 mg/dL and glycemia > 110 mg/dL. Over a total test period of 30 days, 10 individuals (the symbiotic group) consumed a daily dose of 200 mL of a symbiotic shake containing 10(8) UFC/mL Lactobacillus acidophilus, 10(8) UFC/mL Bifidobacterium bifidum and 2 g oligofructose, while 10 other volunteers (the placebo group) drank daily the same amount of a shake that did not contain any symbiotic bacteria. Blood samples were collected 15 days prior to the start of the experiment and at 10-day intervals after the beginning of the shake intake. The standard lipid profile (total cholesterol, triglycerides and HDL cholesterol) and glycemia, or blood sugar levels, were evaluated by an enzyme colorimetric assay. The results of the symbiotic group showed a non-significant reduction (P > 0.05) in total cholesterol and triglycerides, a significant increase (P < 0.05) in HDL cholesterol and a significant reduction (P < 0.05) in fasting glycemia. No significant changes were observed in the placebo group. The consumption of symbiotic shake resulted in a significant increase in HDL and a significant decrease of glycemia.

Distributed cable sensors with memory feature for post-disaster damage assessment

NASA Astrophysics Data System (ADS)

Chen, Genda; McDaniel, Ryan D.; Pommerenke, David J.; Sun, Shishuang

2005-05-01

A new design of distributed crack sensors is presented for the condition assessment of reinforced concrete (RC) structures during and immediately after an earthquake event. This study is mainly focused on the performance of cable sensors under dynamic loading, particularly their ability to memorize the crack history of an RC member. This unique memory feature enables the post-earthquake condition assessment of structural members such as RC columns, in which the earthquake-induced cracks are closed immediately after an earthquake event due to gravity loads and they are visually undetectable. Factors affecting the onset of the memory feature were investigated experimentally with small-scale RC beams under cyclic loading. Test results indicated that both crack width and the number of loading cycles were instrumental in the onset of the memory feature of cable sensors. Practical issues related to dynamic acquisition with the sensors were discussed. The sensors were proven to be fatigue resistant from the shake table tests of RC columns. They continued to show useful signal after the columns can no longer support additional loads.

Evaluation of ground motion scaling methods for analysis of structural systems

USGS Publications Warehouse

O'Donnell, A. P.; Beltsar, O.A.; Kurama, Y.C.; Kalkan, E.; Taflanidis, A.A.

2011-01-01

Ground motion selection and scaling comprises undoubtedly the most important component of any seismic risk assessment study that involves time-history analysis. Ironically, this is also the single parameter with the least guidance provided in current building codes, resulting in the use of mostly subjective choices in design. The relevant research to date has been primarily on single-degree-of-freedom systems, with only a few studies using multi-degree-of-freedom systems. Furthermore, the previous research is based solely on numerical simulations with no experimental data available for the validation of the results. By contrast, the research effort described in this paper focuses on an experimental evaluation of selected ground motion scaling methods based on small-scale shake-table experiments of re-configurable linearelastic and nonlinear multi-story building frame structure models. Ultimately, the experimental results will lead to the development of guidelines and procedures to achieve reliable demand estimates from nonlinear response history analysis in seismic design. In this paper, an overview of this research effort is discussed and preliminary results based on linear-elastic dynamic response are presented. ?? ASCE 2011.

An equivalent method for optimization of particle tuned mass damper based on experimental parametric study

NASA Astrophysics Data System (ADS)

Lu, Zheng; Chen, Xiaoyi; Zhou, Ying

2018-04-01

A particle tuned mass damper (PTMD) is a creative combination of a widely used tuned mass damper (TMD) and an efficient particle damper (PD) in the vibration control area. The performance of a one-storey steel frame attached with a PTMD is investigated through free vibration and shaking table tests. The influence of some key parameters (filling ratio of particles, auxiliary mass ratio, and particle density) on the vibration control effects is investigated, and it is shown that the attenuation level significantly depends on the filling ratio of particles. According to the experimental parametric study, some guidelines for optimization of the PTMD that mainly consider the filling ratio are proposed. Furthermore, an approximate analytical solution based on the concept of an equivalent single-particle damper is proposed, and it shows satisfied agreement between the simulation and experimental results. This simplified method is then used for the preliminary optimal design of a PTMD system, and a case study of a PTMD system attached to a five-storey steel structure following this optimization process is presented.

Experiments on shells under base excitation

NASA Astrophysics Data System (ADS)

Pellicano, Francesco; Barbieri, Marco; Zippo, Antonio; Strozzi, Matteo

2016-05-01

The aim of the present paper is a deep experimental investigation of the nonlinear dynamics of circular cylindrical shells. The specific problem regards the response of circular cylindrical shells subjected to base excitation. The shells are mounted on a shaking table that furnishes a vertical vibration parallel to the cylinder axis; a heavy rigid disk is mounted on the top of the shells. The base vibration induces a rigid body motion, which mainly causes huge inertia forces exerted by the top disk to the shell. In-plane stresses due to the aforementioned inertias give rise to impressively large vibration on the shell. An extremely violent dynamic phenomenon suddenly appears as the excitation frequency varies up and down close to the linear resonant frequency of the first axisymmetric mode. The dynamics are deeply investigated by varying excitation level and frequency. Moreover, in order to generalise the investigation, two different geometries are analysed. The paper furnishes a complete dynamic scenario by means of: (i) amplitude frequency diagrams, (ii) bifurcation diagrams, (iii) time histories and spectra, (iv) phase portraits and Poincaré maps. It is to be stressed that all the results presented here are experimental.

Fixed Base Modal Testing Using the NASA GRC Mechanical Vibration Facility

NASA Technical Reports Server (NTRS)

Staab, Lucas D.; Winkel, James P.; Suarez, Vicente J.; Jones, Trevor M.; Napolitano, Kevin L.

2016-01-01

The Space Power Facility at NASA's Plum Brook Station houses the world's largest and most powerful space environment simulation facilities, including the Mechanical Vibration Facility (MVF), which offers the world's highest-capacity multi-axis spacecraft shaker system. The MVF was designed to perform sine vibration testing of a Crew Exploration Vehicle (CEV)-class spacecraft with a total mass of 75,000 pounds, center of gravity (cg) height above the table of 284 inches, diameter of 18 feet, and capability of 1.25 gravity units peak acceleration in the vertical and 1.0 gravity units peak acceleration in the lateral directions. The MVF is a six-degree-of-freedom, servo-hydraulic, sinusoidal base-shake vibration system that has the advantage of being able to perform single-axis sine vibration testing of large structures in the vertical and two lateral axes without the need to reconfigure the test article for each axis. This paper discusses efforts to extend the MVF's capabilities so that it can also be used to determine fixed base modes of its test article without the need for an expensive test-correlated facility simulation.

Modeling of a viscoelastic damper and its application in structural control.

PubMed

Mehrabi, M H; Suhatril, Meldi; Ibrahim, Zainah; Ghodsi, S S; Khatibi, Hamed

2017-01-01

Conventional seismic rehabilitation methods may not be suitable for some buildings owing to their high cost and time-consuming foundation work. In recent years, viscoelastic dampers (VEDs) have been widely used in many mid- and high-rise buildings. This study introduces a viscoelastic passive control system called rotary rubber braced damper (RRBD). The RRBD is an economical, lightweight, and easy-to-assemble device. A finite element model considering nonlinearity, large deformation, and material damage is developed to conduct a parametric study on different damper sizes under pushover cyclic loading. The fundamental characteristics of this VED system are clarified by analyzing building structures under cyclic loading. The result show excellent energy absorption and stable hysteresis loops in all specimens. Additionally, by using a sinusoidal shaking table test, the effectiveness of the RRBD to manage the response displacement and acceleration of steel frames is considered. The RRBD functioned at early stages of lateral displacement, indicating that the system is effective for all levels of vibration. Moreover, the proposed damper shows significantly better performance in terms of the column compression force resulting from the brace action compared to chevron bracing (CB).

Analytical Prediction of the Seismic Response of a Reinforced Concrete Containment Vessel

DOE Office of Scientific and Technical Information (OSTI.GOV)

James, R.J.; Rashid, Y.R.; Cherry, J.L.

Under the sponsorship of the Ministry of International Trade and Industry (MITI) of Japan, the Nuclear Power Engineering Corporation (NUPEC) is investigating the seismic behavior of a Reinforced Concrete Containment Vessel (RCCV) through scale-model testing using the high-performance shaking table at the Tadotsu Engineering Laboratory. A series of tests representing design-level seismic ground motions was initially conducted to gather valuable experimental measurements for use in design verification. Additional tests will be conducted with increasing amplifications of the seismic input until a structural failure of the test model occurs. In a cooperative program with NUPEC, the US Nuclear Regulatory Commission (USNRC),more » through Sandia National Laboratories (SNL), is conducting analytical research on the seismic behavior of RCCV structures. As part of this program, pretest analytical predictions of the model tests are being performed. The dynamic time-history analysis utilizes a highly detailed concrete constitutive model applied to a three-dimensional finite element representation of the test structure. This paper describes the details of the analysis model and provides analysis results.« less

Numerical simulation on the seismic absorption effect of the cushion in rigid-pile composite foundation

NASA Astrophysics Data System (ADS)

Han, Xiaolei; Li, Yaokun; Ji, Jing; Ying, Junhao; Li, Weichen; Dai, Baicheng

2016-06-01

In order to quantitatively study the seismic absorption effect of the cushion on a superstructure, a numerical simulation and parametric study are carried out on the overall FEA model of a rigid-pile composite foundation in ABAQUS. A simulation of a shaking table test on a rigid mass block is first completed with ABAQUS and EERA, and the effectiveness of the Drucker-Prager constitutive model and the finite-infinite element coupling method is proved. Dynamic time-history analysis of the overall model under frequent and rare earthquakes is carried out using seismic waves from the El Centro, Kobe, and Bonds earthquakes. The different responses of rigid-pile composite foundations and pile-raft foundations are discussed. Furthermore, the influence of thickness and modulus of cushion, and ground acceleration on the seismic absorption effect of the cushion are analyzed. The results show that: 1) the seismic absorption effect of a cushion is good under rare earthquakes, with an absorption ratio of about 0.85; and 2) the seismic absorption effect is strongly affected by cushion thickness and ground acceleration.

Simplified dynamic analysis to evaluate liquefaction-induced lateral deformation of earth slopes: a computational fluid dynamics approach

NASA Astrophysics Data System (ADS)

Jafarian, Yaser; Ghorbani, Ali; Ahmadi, Omid

2014-09-01

Lateral deformation of liquefiable soil is a cause of much damage during earthquakes, reportedly more than other forms of liquefaction-induced ground failures. Researchers have presented studies in which the liquefied soil is considered as viscous fluid. In this manner, the liquefied soil behaves as non-Newtonian fluid, whose viscosity decreases as the shear strain rate increases. The current study incorporates computational fluid dynamics to propose a simplified dynamic analysis for the liquefaction-induced lateral deformation of earth slopes. The numerical procedure involves a quasi-linear elastic model for small to moderate strains and a Bingham fluid model for large strain states during liquefaction. An iterative procedure is considered to estimate the strain-compatible shear stiffness of soil. The post-liquefaction residual strength of soil is considered as the initial Bingham viscosity. Performance of the numerical procedure is examined by using the results of centrifuge model and shaking table tests together with some field observations of lateral ground deformation. The results demonstrate that the proposed procedure predicts the time history of lateral ground deformation with a reasonable degree of precision.

Spring tube braces for seismic isolation of buildings

NASA Astrophysics Data System (ADS)

Karayel, V.; Yuksel, Ercan; Gokce, T.; Sahin, F.

2017-01-01

A new low-cost seismic isolation system based on spring tube bracings has been proposed and studied at the Structural and Earthquake Engineering Laboratory of Istanbul Technical University. Multiple compression-type springs are positioned in a special cylindrical tube to obtain a symmetrical response in tension and compression-type axial loading. An isolation floor, which consists of pin-ended steel columns and spring tube bracings, is constructed at the foundation level or any intermediate level of the building. An experimental campaign with three stages was completed to evaluate the capability of the system. First, the behavior of the spring tubes subjected to axial displacement reversals with varying frequencies was determined. In the second phase, the isolation floor was assessed in the quasi-static tests. Finally, a ¼ scaled 3D steel frame was tested on the shake table using actual acceleration records. The transmitted acceleration to the floor levels is greatly diminished because of the isolation story, which effects longer period and higher damping. There are no stability and self-centering problems in the isolation floor.

The O-mannosylation and production of recombinant APA (45/47 KDa) protein from Mycobacterium tuberculosis in Streptomyces lividans is affected by culture conditions in shake flasks.

PubMed

Gamboa-Suasnavart, Ramsés A; Valdez-Cruz, Norma A; Cordova-Dávalos, Laura E; Martínez-Sotelo, José A; Servín-González, Luis; Espitia, Clara; Trujillo-Roldán, Mauricio A

2011-12-20

The Ala-Pro-rich O-glycoprotein known as the 45/47 kDa or APA antigen from Mycobacterium tuberculosis is an immunodominant adhesin restricted to mycobacterium genus and has been proposed as an alternative candidate to generate a new vaccine against tuberculosis or for diagnosis kits. In this work, the recombinant O-glycoprotein APA was produced by the non-pathogenic filamentous bacteria Streptomyces lividans, evaluating three different culture conditions. This strain is known for its ability to produce heterologous proteins in a shorter time compared to M. tuberculosis. Three different shake flask geometries were used to provide different shear and oxygenation conditions; and the impact of those conditions on the morphology of S. lividans and the production of rAPA was characterized and evaluated. Small unbranched free filaments and mycelial clumps were found in baffled and coiled shake flasks, but one order of magnitude larger pellets were found in conventional shake flasks. The production of rAPA is around 3 times higher in small mycelia than in larger pellets, most probably due to difficulties in mass transfer inside pellets. Moreover, there are four putative sites of O-mannosylation in native APA, one of which is located at the carboxy-terminal region. The carbohydrate composition of this site was determined for rAPA by mass spectrometry analysis, and was found to contain different glycoforms depending on culture conditions. Up to two mannoses residues were found in cultures carried out in conventional shake flasks, and up to five mannoses residues were determined in coiled and baffled shake flasks. The shear and/or oxygenation parameters determine the bacterial morphology, the productivity, and the O-mannosylation of rAPA in S. lividans. As demonstrated here, culture conditions have to be carefully controlled in order to obtain recombinant O-glycosylated proteins with similar "quality" in bacteria, particularly, if the protein activity depends on the glycosylation pattern. Furthermore, it will be an interesting exercise to determine the effect of shear and oxygen in shake flasks, to obtain evidences that may be useful in scaling-up these processes to bioreactors. Another approach will be using lab-scale bioreactors under well-controlled conditions, and study the impact of those on rAPA productivity and quality.

Isolating social influences on vulnerability to earthquake shaking: identifying cost-effective mitigation strategies.

NASA Astrophysics Data System (ADS)

Bhloscaidh, Mairead Nic; McCloskey, John; Pelling, Mark; Naylor, Mark

2013-04-01

Until expensive engineering solutions become more universally available, the objective targeting of resources at demonstrably effective, low-cost interventions might help reverse the trend of increasing mortality in earthquakes. Death tolls in earthquakes are the result of complex interactions between physical effects, such as the exposure of the population to strong shaking, and the resilience of the exposed population along with supporting critical infrastructures and institutions. The identification of socio-economic factors that contribute to earthquake mortality is crucial to identifying and developing successful risk management strategies. Here we develop a quantitative methodology more objectively to assess the ability of communities to withstand earthquake shaking, focusing on, in particular, those cases where risk management performance appears to exceed or fall below expectations based on economic status. Using only published estimates of the shaking intensity and population exposure for each earthquake, data that is available for earthquakes in countries irrespective of their level of economic development, we develop a model for mortality based on the contribution of population exposure to shaking only. This represents an attempt to remove, as far as possible, the physical causes of mortality from our analysis (where we consider earthquake engineering to reduce building collapse among the socio-economic influences). The systematic part of the variance with respect to this model can therefore be expected to be dominated by socio-economic factors. We find, as expected, that this purely physical analysis partitions countries in terms of basic socio-economic measures, for example GDP, focusing analytical attention on the power of economic measures to explain variance in observed distributions of earthquake risk. The model allows the definition of a vulnerability index which, although broadly it demonstrates the expected income-dependence of vulnerability to strong shaking, also identifies both anomalously resilient and anomalously vulnerable countries. We argue that this approach has the potential to direct sociological investigations to expose the underlying causes of the observed non-economic differentiation of vulnerability. At one level, closer study of the earthquakes represented by these data points might expose local or national interventions which are increasing resilience of communities to strong shaking in the absence of major national investment. Ultimately it may contribute to the development of a quantitative evaluation of risk management effectiveness at the national level that can be used better to target and track risk management investments.

Preparing a population for an earthquake like Chi-Chi: The Great Southern California ShakeOut

USGS Publications Warehouse

Jones, Lucile M.; ,

2009-01-01

The Great Southern California ShakeOut was a week of special events featuring the largest earthquake drill in United States history. On November 13, 2008, over 5 million southern Californians pretended that a magnitude-7.8 earthquake had occurred and practiced actions that could reduce its impact on their lives. The primary message of the ShakeOut is that what we do now, before a big earthquake, will determine what our lives will be like after. The drill was based on a scenario of the impacts and consequences of such an earthquake on the Southern San Andreas Fault, developed by over 300 experts led by the U.S. Geological Survey in partnership with the California Geological Survey, the Southern California Earthquake Center, Earthquake Engineering Research Institute, lifeline operators, emergency services and many other organizations. The ShakeOut campaign was designed and implemented by earthquake scientists, emergency managers, sociologists, art designers and community participants. The means of communication were developed using results from sociological research on what encouraged people to take action. This was structured around four objectives: 1) consistent messages – people are more inclined to believe something when they hear the same thing from multiple sources; 2) visual reinforcement – people are more inclined to do something they see other people doing; 3) encourage “milling” or discussing contemplated action – people need to discuss an action with others they care about before committing to undertaking it; and 4) focus on concrete actions – people are more likely to prepare for a set of concrete consequences of a particular hazard than for an abstract concept of risk. The goals of the ShakeOut were established in Spring 2008 and were: 1) to register 5 million people to participate in the drill; 2) to change the culture of earthquake preparedness in southern California; and 3) to reduce earthquake losses in southern California. All of these goals were met. The final registration at www.shakeout.org for the 2008 ShakeOut was 5.47 million people, or one-quarter of the population of the region. A survey conducted with the registered participants showed that the messages they took from the ShakeOut were the concepts intended, including the importance of “Drop, Cover, Hold On”, the interdependency of earthquake risk (“We are all in this together”) and the possibility of reducing losses through preparation and mitigation. Sales data from the Home Depot hardware stores in southern California showed a 260% increase in the sale of earthquake safety products during the month of the ShakeOut, November 2008.

Finite-Fault and Other New Capabilities of CISN ShakeAlert

NASA Astrophysics Data System (ADS)

Boese, M.; Felizardo, C.; Heaton, T. H.; Hudnut, K. W.; Hauksson, E.

2013-12-01

Over the past 6 years, scientists at Caltech, UC Berkeley, the Univ. of Southern California, the Univ. of Washington, the US Geological Survey, and ETH Zurich (Switzerland) have developed the 'ShakeAlert' earthquake early warning demonstration system for California and the Pacific Northwest. We have now started to transform this system into a stable end-to-end production system that will be integrated into the daily routine operations of the CISN and PNSN networks. To quickly determine the earthquake magnitude and location, ShakeAlert currently processes and interprets real-time data-streams from several hundred seismic stations within the California Integrated Seismic Network (CISN) and the Pacific Northwest Seismic Network (PNSN). Based on these parameters, the 'UserDisplay' software predicts and displays the arrival and intensity of shaking at a given user site. Real-time ShakeAlert feeds are currently being shared with around 160 individuals, companies, and emergency response organizations to gather feedback about the system performance, to educate potential users about EEW, and to identify needs and applications of EEW in a future operational warning system. To improve the performance during large earthquakes (M>6.5), we have started to develop, implement, and test a number of new algorithms for the ShakeAlert system: the 'FinDer' (Finite Fault Rupture Detector) algorithm provides real-time estimates of locations and extents of finite-fault ruptures from high-frequency seismic data. The 'GPSlip' algorithm estimates the fault slip along these ruptures using high-rate real-time GPS data. And, third, a new type of ground-motion prediction models derived from over 415,000 rupture simulations along active faults in southern California improves MMI intensity predictions for large earthquakes with consideration of finite-fault, rupture directivity, and basin response effects. FinDer and GPSlip are currently being real-time and offline tested in a separate internal ShakeAlert installation at Caltech. Real-time position and displacement time series from around 100 GPS sensors are obtained in JSON format from RTK/PPP(AR) solutions using the RTNet software at USGS Pasadena. However, we have also started to investigate the usage of onsite (in-receiver) processing using NetR9 with RTX and tracebuf2 output format. A number of changes to the ShakeAlert processing, xml message format, and the usage of this information in the UserDisplay software were necessary to handle the new finite-fault and slip information from the FinDer and GPSlip algorithms. In addition, we have developed a framework for end-to-end off-line testing with archived and simulated waveform data using the Earthworm tankplayer. Detailed background information about the algorithms, processing, and results from these test runs will be presented.

A Comparison of Three Online Information Retrieval Services.

ERIC Educational Resources Information Center

Zais, Harriet W.

Three firms which offer online information retrieval are compared. The firms are Lockheed Information Service, System Development Corporation and the Western Research Application Center. Comparison tables provide information such as hours accessible, coverage, file update, search elements and cost figures for 15 data bases. In addition, general…

An impact of moss sample cleaning on uncertainty of analytical measurement and pattern profiles of rare earth elements.

PubMed

Dołęgowska, Sabina; Gałuszka, Agnieszka; Migaszewski, Zdzisław M

2017-12-01

The main source of rare earth elements (REE) in mosses is atmospheric deposition of particles. Sample treatment operations including shaking, rinsing or washing, which are made in a standard way on moss samples prior to chemical analysis, may lead to removing particles adsorbed onto their tissues. This in turn causes differences in REE concentrations in treated and untreated samples. For the present study, 27 combined moss samples were collected within three wooded areas and prepared for REE determinations by ICP-MS using both manual cleaning by shaking and triple rinsing with deionized water. Higher concentrations of REE were found in manually cleaned samples. The comparison of REE signatures and shale-normalized REE concentration patterns showed that the treatment procedure did not lead to fractionation of REE. All the samples were enriched in medium rare earth elements, and the δMREE factor remained practically unchanged after rinsing. Positive anomalies of Nd, Sm, Eu, Gd, Er and Yb were observed in both, manually cleaned and rinsed samples. For all the elements examined, analytical uncertainty was below 3.0% whereas sample preparation uncertainty computed with ANOVA, RANOVA, modified RANOVA and range statistics methods varied from 3.5 to 29.7%. In most cases the lowest s rprep values were obtained with the modified RANOVA method. Copyright © 2017 Elsevier Ltd. All rights reserved.

Secondary Analysis of the "Love Me...Never Shake Me" SBS Education Program

ERIC Educational Resources Information Center

Deyo, Grace; Skybo, Theresa; Carroll, Alisa

2008-01-01

Objective: Shaken baby syndrome (SBS) is preventable; however, an estimated 21-74 per 100,000 children worldwide are victims annually. This study examined the effectiveness of an SBS prevention program in the US. Methods: A descriptive, secondary analysis of the Prevent Child Abuse Ohio (PCAO) "Love Me...Never Shake Me" SBS education program…

Shake, Rattle, & Roll: Teaching Guide & Poster. Expect the Unexpected with Math[R

ERIC Educational Resources Information Center

Actuarial Foundation, 2013

2013-01-01

"Shake, Rattle, & Roll" is a new program developed by The Actuarial Foundation with Scholastic, provides dynamic real-world math content designed to build student skills while showing students the relevance of math to understanding their world and planning for their future. Math skills are increasingly important for students. According to the U.S.…

The 2011 Virginia earthquake: what are scientists learning?

USGS Publications Warehouse

Horton, J. Wright; Williams, Robert A.

2012-01-01

Nearly 1 year ago, on 23 August, tens of millions of people in the eastern United States and southeastern Canada were startled in the middle of their workday (1:51 P.M. local time) by the sudden onset of moderate to strong ground shaking from a rare magnitude (M) 5.8 earthquake in central Virginia. Treating the shaking as if it were a fire drill, millions of workers in Washington, D. C., New York City, and other eastern cities hurriedly exited their buildings, exposing themselves to potentially greater danger from falling bricks and glass; “drop, cover, and hold” would have been a better response. Fortunately, the strong shaking stopped after about 5 seconds and did not cause widespread severe damage or serious injuries.

Preparation of edge states by shaking boundaries

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shi, Z.C.; Center for Quantum Sciences and School of Physics, Northeast Normal University, Changchun 130024; Hou, S.C.

2016-10-15

Preparing topological states of quantum matter, such as edge states, is one of the most important directions in condensed matter physics. In this work, we present a proposal to prepare edge states in Aubry–André–Harper (AAH) model with open boundaries, which takes advantage of Lyapunov control to design operations. We show that edge states can be obtained with almost arbitrary initial states. A numerical optimalization for the control is performed and the dependence of control process on the system size is discussed. The merit of this proposal is that the shaking exerts only on the boundaries of the model. As amore » by-product, a topological entangled state is achieved by elaborately designing the shaking scheme.« less

Comparison of Circumference Measures and Height-Weight Tables With Dual-Energy X-Ray Absorptiometry Assessment of Body Composition in R.O.T.C. Cadets.

PubMed

Mitchell, Katherine M; Pritchett, Robert C; Gee, David L; Pritchett, Kelly L

2017-09-01

Mitchell, KM, Pritchett, RC, Gee, DL, and Pritchett, KL. Comparison of circumference measures and height-weight tables with dual-energy X-ray absorptiometry assessment of body composition in R.O.T.C. cadets. J Strength Cond Res 31(9): 2552-2556, 2017-Height-weight tables and circumference measures are used by the U.S. Army to predict body composition because they require little equipment or expertise. However, agreement between the Army's new 2002 circumference equation and an established laboratory technique has not been determined. The purpose of this study was to quantify agreement in body fat percentages between the Army's circumference measures (taping) and dual-energy X-ray absorptiometry (DXA); second to determine categorical agreement between height-weight tables and DXA. Male Reserve Officer Training Corps (R.O.T.C.) cadets (N = 23; 20.6 ± 1.6 years, 179.1 ± 6.6 cm; 81.4 ± 10.3 kg) were taped according to Army protocol to predict body fat. The % body fat prediction was compared with DXA through a Bland-Altman Plot with ±2-4% body fat established as a zone of agreement (ZOA). Thirteen out of 23 cadets fell outside the ZOA. No cadet was over the compliance threshold (20-22% fat) using the tape method, however, with DXA, 7 out of 23 cadets were noncompliant. Height-weight tables provided a moderate level of categorical agreement with DXA. The results depict poor agreement between taping and DXA, as taping generally underestimated % body fat. Compared with taping, height-weight tables were better able to identify excess fat weight.

Farm Tractor Tune-Up and Service Specifications.

ERIC Educational Resources Information Center

Bryant, J. G.; And Others

Tune-up and service specifications for 10 major tractor manufacturers are presented in the handbook. In addition, the following tables are included: (1) spark plug heat-range comparisons, (2) freezing protection, (3) pressures for farm tractor tires, (4) use of calcium chloride for liquid weighting, (5) comparisons of American Petroleum Institute…

On Capillary Rise and Nucleation

ERIC Educational Resources Information Center

Prasad, R.

2008-01-01

A comparison of capillary rise and nucleation is presented. It is shown that both phenomena result from a balance between two competing energy factors: a volume energy and a surface energy. Such a comparison may help to introduce nucleation with a topic familiar to the students, capillary rise. (Contains 1 table and 3 figures.)

Underwater Sound Radiation from Large Raindrops

DTIC Science & Technology

1991-09-01

decreasing shape of the impact spectrum, one must pick a reference point rather that a peak value to compare one drop with another. For comparison of...34 1. Type I Bubble Spectral Density and Peak Pressure ............... 34 2. Type II Bubble Average Spectral Densities at 1 m on Axis (20 C...32 Table 4. TYPE II BUBBLE AVERAGE PEAK SPECTRAL DENSITY SU M M A RY ............................................. 39 Table 5. SUMMARY

Soviet Free-Electron Laser Research

DTIC Science & Technology

1985-05-01

can generate a narrow band electromagnetic radiation over a wide frequency range that can potentially extend from microwaves through the visible and...refer to experiments listed in Table 2. Table 2 COMPARISON OF SOVIET-U.S. HIGH-CURRENT FEL EXPERIMENT S SOVIET u.s. Pulse line accelerators...Power ... Pulse length Efficiency . 3cm 10MW 0.7 p.sec 1.5% 2. Columbia, 2 February 1977 [9] Hollow electron beam Energy

Solar Kilns: Feasibility of Utilizing Solar Energy for Drying Lumber in Developing Countries,

DTIC Science & Technology

1977-01-01

Design. .. ............. ... 52 Direct ( Greenhouse ) Design .. .. ............ ... 57 Literature Cited and Partial Bibliography of Solar Lumber Drying...experimental performance of a greenhouse -type solar kiln in Puerto Rico. (Chudnoff et al., 1966). 36"J. Table 9.--Comparison of experimental and calculated...at one dryer orientation (long axis north-south) from 30 percent to 10 percent moisture content. 49 Table 15.-- Greenhouse -type solar kiln capacity

The TeraShake Computational Platform for Large-Scale Earthquake Simulations

NASA Astrophysics Data System (ADS)

Cui, Yifeng; Olsen, Kim; Chourasia, Amit; Moore, Reagan; Maechling, Philip; Jordan, Thomas

Geoscientific and computer science researchers with the Southern California Earthquake Center (SCEC) are conducting a large-scale, physics-based, computationally demanding earthquake system science research program with the goal of developing predictive models of earthquake processes. The computational demands of this program continue to increase rapidly as these researchers seek to perform physics-based numerical simulations of earthquake processes for larger meet the needs of this research program, a multiple-institution team coordinated by SCEC has integrated several scientific codes into a numerical modeling-based research tool we call the TeraShake computational platform (TSCP). A central component in the TSCP is a highly scalable earthquake wave propagation simulation program called the TeraShake anelastic wave propagation (TS-AWP) code. In this chapter, we describe how we extended an existing, stand-alone, wellvalidated, finite-difference, anelastic wave propagation modeling code into the highly scalable and widely used TS-AWP and then integrated this code into the TeraShake computational platform that provides end-to-end (initialization to analysis) research capabilities. We also describe the techniques used to enhance the TS-AWP parallel performance on TeraGrid supercomputers, as well as the TeraShake simulations phases including input preparation, run time, data archive management, and visualization. As a result of our efforts to improve its parallel efficiency, the TS-AWP has now shown highly efficient strong scaling on over 40K processors on IBM’s BlueGene/L Watson computer. In addition, the TSCP has developed into a computational system that is useful to many members of the SCEC community for performing large-scale earthquake simulations.

High-speed shaking of frozen blood clots for extraction of human and malaria parasite DNA

PubMed Central

2011-01-01

Background Frozen blood clots remaining after serum collection is an often disregarded source of host and pathogen DNA due to troublesome handling and suboptimal outcome. Methods High-speed shaking of clot samples in a cell disruptor manufactured for homogenization of tissue and faecal specimens was evaluated for processing frozen blood clots for DNA extraction. The method was compared to two commercial clot protocols based on a chemical kit and centrifugation through a plastic sieve, followed by the same DNA extraction protocol. Blood clots with different levels of parasitaemia (1-1,000 p/μl) were prepared from parasite cultures to assess sensitivity of PCR detection. In addition, clots retrieved from serum samples collected within two epidemiological studies in Kenya (n = 630) were processed by high speed shaking and analysed by PCR for detection of malaria parasites and the human α-thalassaemia gene. Results High speed shaking succeeded in fully dispersing the clots and the method generated the highest DNA yield. The level of PCR detection of P. falciparum parasites and the human thalassaemia gene was the same as samples optimally collected with an anticoagulant. The commercial clot protocol and centrifugation through a sieve failed to fully dissolve the clots and resulted in lower sensitivity of PCR detection. Conclusions High speed shaking was a simple and efficacious method for homogenizing frozen blood clots before DNA purification and resulted in PCR templates of high quality both from humans and malaria parasites. This novel method enables genetic studies from stored blood clots. PMID:21824391

Development of a globally applicable model for near real-time prediction of seismically induced landslides

USGS Publications Warehouse

Nowicki, M. Anna; Wald, David J.; Hamburger, Michael W.; Hearne, Mike; Thompson, Eric M.

2014-01-01

Substantial effort has been invested to understand where seismically induced landslides may occur in the future, as they are a costly and frequently fatal threat in mountainous regions. The goal of this work is to develop a statistical model for estimating the spatial distribution of landslides in near real-time around the globe for use in conjunction with the U.S. Geological Survey (USGS) Prompt Assessment of Global Earthquakes for Response (PAGER) system. This model uses standardized outputs of ground shaking from the USGS ShakeMap Atlas 2.0 to develop an empirical landslide probability model, combining shaking estimates with broadly available landslide susceptibility proxies, i.e., topographic slope, surface geology, and climate parameters. We focus on four earthquakes for which digitally mapped landslide inventories and well-constrainedShakeMaps are available. The resulting database is used to build a predictive model of the probability of landslide occurrence. The landslide database includes the Guatemala (1976), Northridge (1994), Chi-Chi (1999), and Wenchuan (2008) earthquakes. Performance of the regression model is assessed using statistical goodness-of-fit metrics and a qualitative review to determine which combination of the proxies provides both the optimum prediction of landslide-affected areas and minimizes the false alarms in non-landslide zones. Combined with near real-time ShakeMaps, these models can be used to make generalized predictions of whether or not landslides are likely to occur (and if so, where) for earthquakes around the globe, and eventually to inform loss estimates within the framework of the PAGER system.

Use of shaking treatments and preharvest sprays of pyrethroid insecticides to reduce risk of yellowjackets and other insects on Christmas trees imported into Hawaii.

PubMed

Hollingsworth, Robert G; Chastagner, Gary A; Reimer, Neil J; Oishi, Darcy E; Landolt, Peter J; Paull, Robert E

2009-02-01

Insects are commonly found by Hawaii's quarantine inspectors on Christmas trees imported from the Pacific Northwest. To reduce the risk of importing yellowjacket (Vespula spp.) queens and other insects, an inspection and tree shaking certification program was begun in 1990. From 1993 to 2006, the annual percentage of shipped containers rated by Hawaii quarantine inspectors as moderately or highly infested with insects was significantly higher for manually shaken trees than for mechanically shaken trees. Between 1993 and 2001, 343 insect species in total were recovered from Christmas trees. Live western yellowjacket [Vespula pensylvanica (Saussure)] queens were intercepted both from containers certified as manually shaken and from containers certified as mechanically shaken. The standard manual shaking protocol removed about one-half of the queens from Douglas fir [Pseudotsuga menziesii (Mirb.) Franco] trees that were naturally infested with western yellowjacket queens. We investigated the use of preharvest sprays of permethrin as a complement to shaking procedures used to control yellowjackets and other insects. Western yellowjacket queens and honey bees (surrogates for wasp pests) were exposed to Noble fir foliage that had been sprayed in the field with permethrin > 6 wk before harvest. Pesticide residues provided complete control (moribundity or mortality) in both species. The sprays did not affect needle retention or quality of Noble fir foliage. We conclude that preharvest sprays of pyrethroid insecticides could be used in combination with mechanical shaking to greatly reduce the quarantine risk of yellowjacket queens and other insects in exported Christmas trees.

Density-Functional-Theory-Based Equation-of-State Table of Beryllium for Inertial Confinement Fusion Applications

NASA Astrophysics Data System (ADS)

Ding, Y. H.; Hu, S. X.

2017-10-01

Beryllium has been considered a superior ablator material for inertial confinement fusion target designs. Based on density-functional-theory calculations, we have established a wide-range beryllium equation-of-state (EOS) table of density ρ = 0.001 to ρ = 500 g/cm3 and temperature T = 2000 to 108 K. Our first-principles equation-of-state (FPEOS) table is in better agreement with widely used SESAMEEOS table (SESAME2023) than the average-atom INFERNOmodel and the Purgatoriomodel. For the principal Hugoniot, our FPEOS prediction shows 10% stiffer behavior than the last two models at maximum compression. Comparisons between FPEOS and SESAMEfor off-Hugoniot conditions show that both the pressure and internal energy differences are within 20% between two EOS tables. By implementing the FPEOS table into the 1-D radiation-hydrodynamics code LILAC, we studied the EOS effects on beryllium target-shell implosions. The FPEOS simulation predicts up to an 15% higher neutron yield compared to the simulation using the SESAME2023 EOS table. This material is based upon work supported by the Department of Energy National Nuclear Security Administration under Award Number DE-NA0001944.

Topology Design for Directional Range Extension Networks with Antenna Blockage

DTIC Science & Technology

2017-03-19

introduced by pod-based antenna blockages. Using certain modeling approximations, the paper presents a quantitative analysis showing design trade-offs...parameters. Sec- tion IV develops quantitative relationships among key design elements and performance metrics. Section V considers some implications of the...Topology Design for Directional Range Extension Networks with Antenna Blockage Thomas Shake MIT Lincoln Laboratory shake@ll.mit.edu Abstract

Superheat recovery system shakes savings out of A/C systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1985-09-01

One of the most productive and least expensive methods of recovering waste heat is a system that reclaims the excess energy or superheat generated by closed-loop-air conditioning or refrigeration cycles. Installed recently in 72 Steak N' Shakes restaurants as part of a total energy conservation package, it has helped cut gas bills by more than 70%.

Economic resilience lessons from the ShakeOut earthquake scenario

USGS Publications Warehouse

Wein, A.; Rose, A.

2011-01-01

Following a damaging earthquake, “business interruption” (BI)—reduced production of goods and services—begins and continues long after the ground shaking stops. Economic resilience reduces BI losses by making the best use of the resources available at a given point in time (static resilience) or by speeding recovery through repair and reconstruction (dynamic resilience), in contrast to mitigation that prevents damage in the first place. Economic resilience is an important concept to incorporate into economic loss modeling and in recovery and contingency planning. Economic resilience framework includes the applicability of resilience strategies to production inputs and output, demand- and supply-side effects, inherent and adaptive abilities, and levels of the economy. We use our resilience framework to organize and share strategies that enhance economic resilience, identify overlooked resilience strategies, and present evidence and structure of resilience strategies for economic loss modelers. Numerous resilience strategies are compiled from stakeholder discussions about the ShakeOut Scenario (Jones et. al. 2008). Modeled results of ShakeOut BI sector losses reveal variable effectiveness of resilience strategies for lengthy disruptions caused by fire-damaged buildings and water service outages. Resilience is a complement to mitigation and may, in fact, have cost and all-hazards advantages.

ShakeMap-based prediction of earthquake-induced mass movements in Switzerland calibrated on historical observations

USGS Publications Warehouse

Cauzzi, Carlo; Fah, Donat; Wald, David J.; Clinton, John; Losey, Stephane; Wiemer, Stefan

2018-01-01

In Switzerland, nearly all historical Mw ~ 6 earthquakes have induced damaging landslides, rockslides and snow avalanches that, in some cases, also resulted in damage to infrastructure and loss of lives. We describe the customisation to Swiss conditions of a globally calibrated statistical approach originally developed to rapidly assess earthquake-induced landslide likelihoods worldwide. The probability of occurrence of such earthquake-induced effects is modelled through a set of geospatial susceptibility proxies and peak ground acceleration. The predictive model is tuned to capture the observations from past events and optimised for near-real-time estimates based on USGS-style ShakeMaps routinely produced by the Swiss Seismological Service. Our emphasis is on the use of high-resolution geospatial datasets along with additional local information on ground failure susceptibility. Even if calibrated on historic events with moderate magnitudes, the methodology presented in this paper yields sensible results also for low-magnitude recent events. The model is integrated in the Swiss ShakeMap framework. This study has a high practical relevance to many Swiss ShakeMap stakeholders, especially those managing lifeline systems, and to other global users interested in conducting a similar customisation for their region of interest.

Force-response considerations in ciliary mechanosensation.

PubMed

Resnick, Andrew; Hopfer, Ulrich

2007-08-15

Considerable experimental evidence indicates that the primary, nonmotile cilium is a mechanosensory organelle in several epithelial cell types. As the relationship between cellular responses and nature and magnitude of applied forces is not well understood, we have investigated the effects of exposure of monolayers of renal collecting duct chief cells to orbital shaking and quantified the forces incident on cilia. An exposure of 24 h of these cells to orbital shaking resulted in a decrease of amiloride-sensitive sodium current by approximately 60% and ciliary length by approximately 30%. The sensitivity of the sodium current to shaking was dependent on intact cilia. The drag force on cilia due to induced fluid flow during orbital shaking was estimated at maximally 5.2x10(-3) pN at 2 Hz, approximately 4 times that of thermal noise. The major structural feature of cilia contributing to their sensitivity appears to be ciliary length. As more than half of the total drag force is exerted on the ciliary cap, one function of the slender stalk may be to expose the cap to greater drag force. Regardless, the findings indicate that the cilium is a mechanosensory organelle with a sensitivity much lower than previously recognized.

Instrumental shaking thresholds for seismically induced landslides and preliminary report on landslides triggered by the October 17, 1989, Loma Prieta, California earthquake

USGS Publications Warehouse

Harp, E.L.

1993-01-01

The generation of seismically induced landslide depends on the characteristics of shaking as well as mechanical properties of geologic materials. A very important parameter in the study of seismically induced landslide is the intensity based on a strong-motion accelerogram: it is defined as Arias intensity and is proportional to the duration of the shaking record as well as the amplitude. Having a theoretical relationship between Arias intensity, magnitude and distance it is possible to predict how far away from the seismic source landslides are likely to occur for a given magnitude earthquake. Field investigations have established that the threshold level of Arias intensity depends also on site effects, particularly the fracture characteristics of the outcrops present. -from Author

Evaluating glacier movement fluctuations using remote sensing: A case study of the Baird, Patterson, LeConte, and Shakes glaciers in central Southeastern Alaska

NASA Astrophysics Data System (ADS)

Davidson, Robert Howard

Global Land Survey (GLS) data encompassing Landsat Multispectral Scanner (MSS), Landsat 5's Thematic Mapper (TM), and Landsat 7's Enhanced Thematic Mapper Plus (ETM+) were used to determine the terminus locations of Baird, Patterson, LeConte, and Shakes Glaciers in Alaska in the time period 1975-2010. The sequences of the terminuses locations were investigated to determine the movement rates of these glaciers with respect to specific physical and environmental conditions. GLS data from 1975, 1990, 2000, 2005, and 2010 in false-color composite images enhancing ice-snow differentiation and Iterative Self-Organizing (ISO) Data Cluster Unsupervised Classifications were used to 1) quantify the movement rates of Baird, Patterson, LeConte, and Shakes Glaciers; 2) analyze the movement rates for glaciers with similar terminal terrain conditions and; 3) analyze the movement rates for glaciers with dissimilar terminal terrain conditions. From the established sequence of terminus locations, movement distances were quantified between the glacier locations. Movement distances were then compared to see if any correlation existed between glaciers with similar or dissimilar terminal terrain conditions. The Global Land Ice Measurement from Space (GLIMS) data was used as a starting point from which glacier movement was measured for Baird, Patterson, and LeConte Glaciers only as the Shakes Glacier is currently not included in the GLIMS database. The National Oceanographic and Atmospheric Administration (NOAA) temperature data collected at the Petersburg, Alaska, meteorological station (from January 1, 1973 to December 31, 2009) were used to help in the understanding of the climatic condition in this area and potential impact on glaciers terminus. Results show that glaciers with similar terminal terrain conditions (Patterson and Shakes Glaciers) and glaciers with dissimilar terminal terrain conditions (Baird, Patterson, and LeConte Glaciers) did not exhibit similar movement rates. Glacier movement rates were greatest for glaciers whose terminuses were in fresh water (Patterson and Shakes Glaciers), less for those with terminuses in salt water (LeConte Glacier), and least for glaciers with terminuses on dry land (Baird Glacier).Based upon these findings, the presence of water, especially fresh water, at the terminal end of the Patterson and Shakes Glaciers had a greater effect on glacier movement than slope. Possible explanations for this effect might include a heat sink effect or tidal motions that hasten glacier disintegration in the ablation zone. In a heat sink scenario, the water bodies in which the Patterson and Shakes Glaciers terminus are located could act as a thermal energy transfer medium that increases glacier melting and subsequent retreat. On the other hand, tidal motions could act as horizontal and vertical push/pull forces, which increase the fracturing rate, calving, and subsequent retreat of glaciers terminus that are is salt water like the LeConte Glacier. Over the length of the study period, 1975 through 2010, there has been a 0.85°C increase in annual air temperatures that, although may seem low, may prove important when determining glacial mass balance rates. Further studies are necessary to test these hypotheses to determine if a heat sink effect and tidal motions significantly affected the movement rates for the glaciers in this study area. An additional significant result of this study was the creation of shapefiles delineating the positions of the Shakes Glaciers that are being submitted to the Global Land Ice Measurements from Space (GLIMS) program for inclusion in their master worldwide glacier database.

A Promising Tool to Assess Long Term Public Health Effects of Natural Disasters: Combining Routine Health Survey Data and Geographic Information Systems to Assess Stunting after the 2001 Earthquake in Peru

PubMed Central

Rydberg, Henny; Marrone, Gaetano; Strömdahl, Susanne; von Schreeb, Johan

2015-01-01

Background Research on long-term health effects of earthquakes is scarce, especially in low- and middle-income countries, which are disproportionately affected by disasters. To date, progress in this area has been hampered by the lack of tools to accurately measure these effects. Here, we explored whether long-term public health effects of earthquakes can be assessed using a combination of readily available data sources on public health and geographic distribution of seismic activity. Methods We used childhood stunting as a proxy for public health effects. Data on stunting were attained from Demographic and Health Surveys. Earthquake data were obtained from U.S. Geological Survey’s ShakeMaps, geographic information system-based maps that divide earthquake affected areas into different shaking intensity zones. We combined these two data sources to categorize the surveyed children into different earthquake exposure groups, based on how much their area of residence was affected by the earthquake. We assessed the feasibility of the approach using a real earthquake case – an 8.4 magnitude earthquake that hit southern Peru in 2001. Results and conclusions Our results indicate that the combination of health survey data and disaster data may offer a readily accessible and accurate method for determining the long-term public health consequences of a natural disaster. Our work allowed us to make pre- and post- earthquake comparisons of stunting, an important indicator of the well-being of a society, as well as comparisons between populations with different levels of exposure to the earthquake. Furthermore, the detailed GIS based data provided a precise and objective definition of earthquake exposure. Our approach should be considered in future public health and disaster research exploring the long-term effects of earthquakes and potentially other natural disasters. PMID:26090999

A Promising Tool to Assess Long Term Public Health Effects of Natural Disasters: Combining Routine Health Survey Data and Geographic Information Systems to Assess Stunting after the 2001 Earthquake in Peru.

PubMed

Rydberg, Henny; Marrone, Gaetano; Strömdahl, Susanne; von Schreeb, Johan

2015-01-01

Research on long-term health effects of earthquakes is scarce, especially in low- and middle-income countries, which are disproportionately affected by disasters. To date, progress in this area has been hampered by the lack of tools to accurately measure these effects. Here, we explored whether long-term public health effects of earthquakes can be assessed using a combination of readily available data sources on public health and geographic distribution of seismic activity. We used childhood stunting as a proxy for public health effects. Data on stunting were attained from Demographic and Health Surveys. Earthquake data were obtained from U.S. Geological Survey's ShakeMaps, geographic information system-based maps that divide earthquake affected areas into different shaking intensity zones. We combined these two data sources to categorize the surveyed children into different earthquake exposure groups, based on how much their area of residence was affected by the earthquake. We assessed the feasibility of the approach using a real earthquake case--an 8.4 magnitude earthquake that hit southern Peru in 2001. Our results indicate that the combination of health survey data and disaster data may offer a readily accessible and accurate method for determining the long-term public health consequences of a natural disaster. Our work allowed us to make pre- and post-earthquake comparisons of stunting, an important indicator of the well-being of a society, as well as comparisons between populations with different levels of exposure to the earthquake. Furthermore, the detailed GIS based data provided a precise and objective definition of earthquake exposure. Our approach should be considered in future public health and disaster research exploring the long-term effects of earthquakes and potentially other natural disasters.

Response mechanism of post-earthquake slopes under heavy rainfall

NASA Astrophysics Data System (ADS)

Qiu, Hong-zhi; Kong, Ji-ming; Wang, Ren-chao; Cui, Yun; Huang, Sen-wang

2017-07-01

This paper uses the catastrophic landslide that occurred in Zhongxing Town, Dujiangyan City, as an example to study the formation mechanism of landslides induced by heavy rainfall in the post-Wenchuan earthquake area. The deformation characteristics of a slope under seismic loading were investigated via a shaking table test. The results show that a large number of cracks formed in the slope due to the tensile and shear forces of the vibrations, and most of the cracks had angles of approximately 45° with respect to the horizontal. A series of flume tests were performed to show how the duration and intensity of rainfall influence the responses of the shaken and non-shaken slopes. Wetting fronts were recorded under different rainfall intensities, and the depth of rainfall infiltration was greater in the shaken slope than in the non-shaken slope because the former experienced a greater extreme rainfall intensity under the same early rainfall and rainfall duration conditions. At the beginning of the rainfall infiltration experiment, the pore water pressure in the slope was negative, and settling occurred at the top of the slope. With increasing rainfall, the pore water pressure changed from negative to positive, and cracks were observed on the back surface of the slope and the shear outlet of the landslide on the front of the slope. The shaken slope was more susceptible to crack formation than the non-shaken slope under the same rainfall conditions. A comparison of the responses of the shaken and non-shaken slopes under heavy rainfall revealed that cracks formed by earthquakes provided channels for infiltration. Soil particles in the cracks of slopes were washed away, and the pore water pressure increased rapidly, especially the transient pore water pressure in the slope caused by short-term concentrated rainfall which decreased rock strength and slope stability.

Large eddy simulation/dynamic thickened flame modeling of a high Karlovitz number turbulent premixed jet flame (Supplementary material).

DOE Office of Scientific and Technical Information (OSTI.GOV)

Han, Wang; Wang, Haiou; Kuenne, Guido

This supplementary material complements the article and provides additional information to the chemical mechanism used in this work, boundary conditions for the LES con guration and table generation, comparisons of axial velocities, results from a LES/ nite-rate chemistry (FRC) approach, and results from the LES/DTF/SPF approach with a particular chemistry table that is generated using a single strained premixed amelet solution.

The LIFE Laser Design in Context: A Comparison to the State-of-the-Art

DOE Office of Scientific and Technical Information (OSTI.GOV)

Deri, R J; Bayramian, A J; Erlandson, A C

2011-03-21

The current point design for the LIFE laser leverages decades of solid-state laser development in order to achieve the performance and attributes required for inertial fusion energy. This document provides a brief comparison of the LIFE laser point design to other state-of-the-art solid-state lasers. Table I compares the attributes of the current LIFE laser point design to other systems. the state-of-the-art for single-shot performance at fusion-relevant beamline energies is exemplified by performance observed on the National Ignition Facility. The state-of-the-art for high average power is exemplified by the Northrup Grumman JHPSSL laser. Several items in Table I deal with themore » laser efficiency; a more detailed discussion of efficiency can be found in reference 5. The electrical-to-optical efficiency of the LIFE design exceeds that of reference 4 due to the availability of higher efficiency laser diode pumps (70% vs. {approx}50% used in reference 4). LIFE diode pumps are discussed in greater detail in reference 6. The 'beam steering' state of the art is represented by the deflection device that will be used in the LIFE laser, not a laser system. Inspection of Table I shows that most LIFE laser attributes have already been experimentally demonstrated. The two cases where the LIFE design is somewhat better than prior experimental work do not involve the development of new concepts: beamline power is increased simply by increasing aperture (as demonstrated by the power/aperture comparison in Table I), and efficiency increases are achieved by employing state-of-the-art diode pumps. In conclusion, the attributes anticipated for the LIFE laser are consistent with the demonstrated performance of existing solid-state lasers.« less

Contingency table analysis of pebble lithology and roundness: A case study of Huangshui River, China and comparison to rivers in the Rocky Mountains, USA

USGS Publications Warehouse

Miao, X.; Lindsey, D.A.; Lai, Z.; Liu, Xiuying

2010-01-01

Contingency table analysis of pebble lithology and roundness is an effective way to identify the source terrane of a drainage basin and to distinguish changes in basin size, piracy, tectonism, and other events. First, the analysis to terrace gravel deposited by the Huangshui River, northeastern Tibet Plateau, China, shows statistically contrasting pebble populations for the oldest terrace (T7, Dadongling, 1.2. Ma) and the youngest terraces (T0-T3, ?. 0.15. Ma). Two fluvial processes are considered to explain the contrast in correlation between lithology and roundness in T7 gravel versus T0-T3 gravel: 1) reworking of T7 gravel into T0-T3 gravel and 2) growth in the size of the river basin between T7 and T0-T3 times. We favor growth in basin size as the dominant process, from comparison of pebble counts and contingency tables. Second, comparison of results from Huangshui River of China to three piedmont streams of the Rocky Mountains, USA highlights major differences in source terrane and history. Like Rocky Mountain piedmont gravel from Colorado examples, the Huangshui gravels show a preference (observed versus expected frequency) for rounded granite. But unlike Rocky Mountain gravel, Huangshui gravel shows a preference for angular quartzite and for rounded sandstone. In conclusion, contrasting behavior of lithologies during transport, not always apparent in raw pebble counts, is readily analyzed using contingency tables to identify the provenance of individual lithologies, including recycled clasts. Results of the analysis may help unravel river history, including changes in basin size and lithology. ?? 2009.

KEY COMPARISON: CCQM-K32 key comparison and P84 pilot study: Amount of silicon oxide as a thickness of SiO2 on Si

NASA Astrophysics Data System (ADS)

Seah, M. P.

2008-01-01

CCQM-K32 and P84 were conducted following the pilot study P-38 to demonstrate and document the capability of interested National Metrology Institutes to measure the amount of silicon oxide on silicon wafers expressed as a thickness of SiO2 for nominal thicknesses in the range 1.5 nm to 8 nm. 'Amount of substance' may be expressed in many ways and here the measurand is the thickness of the silicon oxide layer on each of a total of 9 samples of nominal thicknesses in the range 1.5 to 8 nm on (100) and (111) Si substrates, expressed as the thickness of SiO2. This report presents the results from K32 and P84. It includes the data received for the measured values and their associated uncertainties, at 95% confidence, for the 9 samples prior to the deadline for receipt of data. The materials are grown by thermal oxidation in very clean furnaces designed for high quality gate oxides on Si wafers in European and US facilities at the same time as those for the pilot study, P-38. Separate samples were provided to each institute in special containers limiting the carbonaceous contamination to below about 0.3 nm. The 9 samples included 5 samples of ultra-thin SiO2 on (100) orientated wafers of Si and 4 samples of ultra-thin SiO2 on (111) orientated wafers of Si. The measurements from the 11 participating laboratories were conducted using ellipsometry, neutron reflectivity (NR), x-ray photoelectron spectroscopy (XPS) or x-ray reflectivity measurements (XRR), guided by the protocol developed in the pilot study P-38 and reproduced in the Appendix. The measurements are given in tables 2 and 3. A very small correction is then made for the different samples that each laboratory received as in table 4. Where appropriate, method offset values deduced from the pilot study P-38 are given in table 5 leading to comparative data in tables 6 and 7. Values for the key comparison reference values (KCRVs) and their associated uncertainties are made from the weighted means and the expanded weighted standard deviations of the means from table 6. This is provided in table 8. Graphical plots of equivalence from tables 6 and 8 are provided in figure 1 and equivalence statements are presented in Annex A. Additional XPS and XRR data from NMIJ for K32 were withdrawn from the KCRV evaluation and are given in Annex B. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCQM, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

Empty calories and phantom fullness: a randomized trial studying the relative effects of energy density and viscosity on gastric emptying determined by MRI and satiety.

PubMed

Camps, Guido; Mars, Monica; de Graaf, Cees; Smeets, Paul Am

2016-07-01

Stomach fullness is a determinant of satiety. Although both the viscosity and energy content have been shown to delay gastric emptying, their relative importance is not well understood. We compared the relative effects of and interactions between the viscosity and energy density on gastric emptying and perceived satiety. A total of 15 healthy men [mean ± SD age: 22.6 ± 2.4 y; body mass index (in kg/m(2)): 22.6 ± 1.8] participated in an experiment with a randomized 2 × 2 crossover design. Participants received dairy-based shakes (500 mL; 50% carbohydrate, 20% protein, and 30% fat) that differed in viscosity (thin and thick) and energy density [100 kcal (corresponding to 0.2 kcal/mL) compared with 500 kcal (corresponding to 1 kcal/mL)]. After ingestion, participants entered an MRI scanner where abdominal scans and oral appetite ratings on a 100-point scale were obtained every 10 min until 90 min after ingestion. From the scans, gastric content volumes were determined. Overall, the gastric emptying half-time (GE t50) was 54.7 ± 3.8 min. The thin 100-kcal shake had the lowest GE t50 of 26.5 ± 3.0 min, followed by the thick 100-kcal shake with a GE t50 of 41 ± 3.9 min and the thin 500-kcal shake with a GE t50 of 69.5 ± 5.9 min, and the thick 500-kcal shake had the highest GE t50 of 81.9 ± 8.3 min. With respect to appetite, the thick 100-kcal shake led to higher fullness (58 points at 40 min) than the thin 500-kcal shake (48 points at 40 min). Our results show that increasing the viscosity is less effective than increasing the energy density in slowing gastric emptying. However, the viscosity is more important to increase the perceived fullness. These results underscore the lack of the satiating efficiency of empty calories in quickly ingested drinks such as sodas. The increase in perceived fullness that is due solely to the increased viscosity, which is a phenomenon that we refer to as phantom fullness, may be useful in lowering energy intake. This trial was registered at www.trialregister.nl as NTR4573. © 2016 American Society for Nutrition.

Intensity distribution and isoseismal maps for the Nisqually, Washington, earthquake of 28 February 2001

USGS Publications Warehouse

Dewey, James W.; Hopper, Margaret G.; Wald, David J.; Quitoriano, Vincent; Adams, Elizabeth R.

2002-01-01

We present isoseismal maps, macroseismic intensities, and community summaries of damage for the MW=6.8 Nisqually, Washington, earthquake of 28 February, 2001. For many communities, two types of macroseismic intensity are assigned, the traditional U.S. Geological Survey Modified Mercalli Intensities (USGS MMI) and a type of intensity newly introduced with this paper, the USGS Reviewed Community Internet Intensity (RCII). For most communities, the RCII is a reviewed version of the Community Internet Intensity (CII) of Wald and others (1999). For some communities, RCII is assigned from such non-CII sources as press reports, engineering reports, and field reconnaissance observations. We summarize differences between procedures used to assign RCII and USGS MMI, and we show that the two types of intensity are nonetheless very similar for the Nisqually earthquake. We do not see evidence for systematic differences between RCII and USGS MMI that would approach one intensity unit, at any level of shaking, but we document a tendency for the RCII to be slightly lower than MMI in regions of low intensity and slightly higher than MMI in regions of high intensity. The highest RCII calculated for the Nisqually earthquake is 7.6, calculated for zip code 98134, which includes the ?south of downtown? (Sodo) area of Seattle and Harbor Island. By comparison, we assigned a traditional USGS MMI 8 to the Sodo area of Seattle. In all, RCII of 6.5 and higher were assigned to 58 zip-code regions. At the lowest intensities, the Nisqually earthquake was felt over an area of approximately 350,000 square km (approximately 135,000 square miles) in Washington, Oregon, Idaho, Montana, and southern British Columbia, Canada. On the basis of macroseismic effects, we infer that shaking in the southern Puget Sound region was somewhat less for the 2001 Nisqually earthquake than for the Puget Sound earthquake of April 13, 1949, which had nearly the same hypocenter and magnitude. Allowing for differences in hypocenter, shaking in the 2001 earthquake was very similar to that produced by the Puget Sound earthquake of April 25, 1965. First-person accounts of the effects of the 2001 earthquake on individual households are given for some communities.

Ortholog Identification and Comparative Analysis of Microbial Genomes Using MBGD and RECOG.

PubMed

Uchiyama, Ikuo

2017-01-01

Comparative genomics is becoming an essential approach for identification of genes associated with a specific function or phenotype. Here, we introduce the microbial genome database for comparative analysis (MBGD), which is a comprehensive ortholog database among the microbial genomes available so far. MBGD contains several precomputed ortholog tables including the standard ortholog table covering the entire taxonomic range and taxon-specific ortholog tables for various major taxa. In addition, MBGD allows the users to create an ortholog table within any specified set of genomes through dynamic calculations. In particular, MBGD has a "My MBGD" mode where users can upload their original genome sequences and incorporate them into orthology analysis. The created ortholog table can serve as the basis for various comparative analyses. Here, we describe the use of MBGD and briefly explain how to utilize the orthology information during comparative genome analysis in combination with the stand-alone comparative genomics software RECOG, focusing on the application to comparison of closely related microbial genomes.

The earthquake of the century in Northwestern Europe: the Roermond, the Netherlands, earthquake of April 13, 1992

USGS Publications Warehouse

van Eck, T.; Ahorner, L.; Paulssen, H.

1993-01-01

Early Monday morning, at 3:20 a.m. local time on April 13, 1992, fierce ground shaking woke up many people in the Dutch province of Limburg and bordering regions in Germany and Belgium. The shaking was caused by an earthquake of Richter magnitude 5.9, centered near the Dutch city of Roermond (see map, next page).

Internal defects associated with pruned and nonpruned branch stubs in black walnut

Treesearch

Alex L. Shigo; E. Allen, Jr. McGinnes; David T. Funk; Nelson Rogers

1979-01-01

Dissections of 50 branch stubs from seven black walnut trees revealed that some discolored wood was associated with all stubs, and that ring shakes and dark bands of discolored wood were associated with 14 of 17 stubs that were "flush cut" (branch collar removed) 13 years earlier while they were living or dead. Ring shakes formed along the barrier zone...

Cross-section perimeter is a suitable parameter to describe the effects of different baffle geometries in shaken microtiter plates

PubMed Central

2014-01-01

Background Biotechnological screening processes are performed since more than 8 decades in small scale shaken bioreactors like shake flasks or microtiter plates. One of the major issues of such reactors is the sufficient oxygen supply of suspended microorganisms. Oxygen transfer into the bulk liquid can in general be increased by introducing suitable baffles at the reactor wall. However, a comprehensive and systematic characterization of baffled shaken bioreactors has never been carried out so far. Baffles often differ in number, size and shape. The exact geometry of baffles in glass lab ware like shake flasks is very difficult to reproduce from piece to piece due to the hard to control flow behavior of molten glass during manufacturing. Thus, reproducibility of the maximum oxygen transfer capacity in such baffled shake flasks is hardly given. Results As a first step to systematically elucidate the general effect of different baffle geometries on shaken bioreactor performance, the maximum oxygen transfer capacity (OTRmax) in baffled 48-well microtiter plates as shaken model reactor was characterized. This type of bioreactor made of plastic material was chosen, as the exact geometry of the baffles can be fabricated by highly reproducible laser cutting. As a result, thirty different geometries were investigated regarding their maximum oxygen transfer capacity (OTRmax) and liquid distribution during shaking. The relative perimeter of the cross-section area as new fundamental geometric key parameter is introduced. An empirical correlation for the OTRmax as function of the relative perimeter, shaking frequency and filling volume is derived. For the first time, this correlation allows a systematic description of the maximum oxygen transfer capacity in baffled microtiter plates. Conclusions Calculated and experimentally determined OTRmax values agree within ± 30% accuracy. Furthermore, undesired out-of-phase operating conditions can be identified by using the relative perimeter as key parameter. Finally, an optimum well geometry characterized by an increased perimeter of 10% compared to the unbaffled round geometry is identified. This study may also assist to comprehensively describe and optimize the baffles of shake flasks in future. PMID:25093039

ShakeAlert Users Transition to the Production Prototype System

NASA Astrophysics Data System (ADS)

Strauss, J. A.; Vinci, M.; Steele, W. P.; Hellweg, M.; Allen, R. M.; DeGroot, R. M.

2016-12-01

The ShakeAlert Earthquake Early Warning system transitioned from the demonstration system into the fully-fledged production prototype system this year. Users were migrated over to the new system concurrent with the release of the ShakeAlert UserDisplay Version 2.5.0. The production prototype system provides robust connectivity, fail-over mechanisms to ensure that alarms are deliverd even if one connection fails, and provides a framework to connect future stations, participants, and other sources as the project expands to the full public system. We will present an overview of key user sectors that are either testing or launching pilot projects for the system within their organizations. We will outline the implementation of certain actions, and highlight accomplishments and challenges the Beta Users encounter in fully implementing ShakeAlert within their organizations. By better studying these issues, project partners can better assist the users in incorporating early warning in their operations. Opening up the system to allow for pilot projects enables ShakeAlert users to develop hardware, software, and policy solutions for actions in response to early warning alerts in a controlled environment. This is the first step on the path toward limited rollouts. The pilot groups leverage the expertise of our stakeholders to develop the `last mile' alert distribution and responses. The transition went smoothly in February 2015, for users in California, and we expect to connect with more beta users and pilot groups in this next phase. User transition is planned for Fall 2016 for users in the Pacific Northwest. Beta Users, such as municipalities, emergency response groups, and county officials, lifelines, schools, and private industry continue to meet with ShakeAlert partners to 1) further education and training on both benefits and limitations 2) strategize on implementation actions, such as opening fire house bay doors in response to an alarm, and 3) coordinate continued engagement as the system comes online with more Users and in more areas. The newly created Joint Committee on Communication, Education, and Outreach is aiding with the education and training aspect of the rollout.

Predicting groundwater level fluctuations with meteorological effect implications—A comparative study among soft computing techniques

NASA Astrophysics Data System (ADS)

Shiri, Jalal; Kisi, Ozgur; Yoon, Heesung; Lee, Kang-Kun; Hossein Nazemi, Amir

2013-07-01

The knowledge of groundwater table fluctuations is important in agricultural lands as well as in the studies related to groundwater utilization and management levels. This paper investigates the abilities of Gene Expression Programming (GEP), Adaptive Neuro-Fuzzy Inference System (ANFIS), Artificial Neural Networks (ANN) and Support Vector Machine (SVM) techniques for groundwater level forecasting in following day up to 7-day prediction intervals. Several input combinations comprising water table level, rainfall and evapotranspiration values from Hongcheon Well station (South Korea), covering a period of eight years (2001-2008) were used to develop and test the applied models. The data from the first six years were used for developing (training) the applied models and the last two years data were reserved for testing. A comparison was also made between the forecasts provided by these models and the Auto-Regressive Moving Average (ARMA) technique. Based on the comparisons, it was found that the GEP models could be employed successfully in forecasting water table level fluctuations up to 7 days beyond data records.

Tables for simplifying calculations of activities produced by thermal neutrons

USGS Publications Warehouse

Senftle, F.E.; Champion, W.R.

1954-01-01

The method of calculation described is useful for the types of work of which examples are given. It is also useful in making rapid comparison of the activities that might be expected from several different elements. For instance, suppose it is desired to know which of the three elements, cobalt, nickel, or vanadium is, under similar conditions, activated to the greatest extent by thermal neutrons. If reference is made to a cross-section table only, the values may be misleading unless properly interpreted by a suitable comparison of half-lives and abundances. In this table all the variables have been combined and the desired information can be obtained directly from the values of A 3??, the activity produced per gram per second of irradiation, under the stated conditions. Hence, it is easily seen that, under similar circumstances of irradiation, vanadium is most easily activated even though the cross section of one of the cobalt isotopes is nearly five times that of vanadium and the cross section of one of the nickel isotopes is three times that of vanadium. ?? 1954 Societa?? Italiana di Fisica.

Quantification of the Effect of Shuttling on Computed Tomography Perfusion Parameters by Investigation of Aortic Inputs on Different Table Positions From Shuttle-Mode Scans of Lung and Liver Tumors.

PubMed

Ghosh, Payel; Chandler, Adam G; Hobbs, Brian P; Sun, Jia; Rong, John; Hong, David; Subbiah, Vivek; Janku, Filip; Naing, Aung; Hwu, Wen-Jen; Ng, Chaan S

The aim of this study was to quantify the effect of shuttling on computed tomography perfusion (CTp) parameters derived from shuttle-mode body CT images using aortic inputs from different table positions. Axial shuttle-mode CT scans were acquired from 6 patients (10 phases, 2 nonoverlapping table positions 1.4 seconds apart) after contrast agent administration. Artifacts resulting from the shuttling motion were corrected with nonrigid registration before computing CTp maps from 4 aortic levels chosen from the most superior and inferior slices of each table position scan. The effect of shuttling on CTp parameters was estimated by mean differences in mappings obtained from aortic inputs in different table positions. Shuttling effect was also quantified using 95% limits of agreement of CTp parameter differences within-table and between-table aortic positions from the interaortic mean CTp values. Blood flow, permeability surface, and hepatic arterial fraction differences were insignificant (P > 0.05) for both within-table and between-table comparisons. The 95% limits of agreement for within-table blood volume (BV) value deviations obtained from lung tumor regions were less than 4.7% (P = 0.18) compared with less than 12.2% (P = 0.003) for between-table BV value deviations. The 95% limits of agreement of within-table deviations for liver tumor regions were less than 1.9% (P = 0.55) for BV and less than 3.2% (P = 0.23) for mean transit time, whereas between-table BV and mean transit time deviations were less than 11.7% (P < 0.01) and less than 14.6% (P < 0.01), respectively. Values for normal liver tissue regions were concordant. Computed tomography perfusion parameters acquired from aortic levels within-table positions generally yielded higher agreement than mappings obtained from aortic levels between-table positions indicating differences due to shuttling effect.

Transient transcriptional activation of the Vibrio cholerae El Tor virulence regulator toxT in response to culture conditions.

PubMed

Medrano, A I; DiRita, V J; Castillo, G; Sanchez, J

1999-05-01

Vibrio cholerae El Tor require special in vitro culture conditions, consisting of an initial static growth period followed by shift to shaking (AKI conditions), for expression of cholera toxin (CT) and toxin coregulated pili (TCP). ToxT, a regulator whose initial transcription depends on the ToxR regulator, positively modulates expression of CT and TCP. To help understand control of CT and TCP in El Tor vibrios, we monitored ctxAB and ToxR-dependent toxT transcription by time course primer extension assays. AKI conditions stimulated CT synthesis with an absence of ctxAB transcription during static growth followed by induction upon shaking. ToxR-dependent toxT transcription was induced at the end of the static growth period but was transient, stopping shortly after shaking was initiated but, interestingly, also if the static phase was prolonged. Immunoblot assays showed that ToxR protein levels were not coincidentally transient, implying a protein on/off switch mechanism for ToxR. Despite the transient activation by ToxR, transcription of ctxAB was maintained during shaking. This finding suggested continued toxT expression, possibly through relay transcription from another promoter. The 12.6-kb distant upstream tcpA promoter responsible for expression of the TCP operon has been proposed to provide an alternate toxT message by readthrough transcription. Activation of the tcpA promoter is supported by increased expression of TcpA protein during the shaking phase of the culture. Readthrough transcription of toxT from tcpA would be compatible with reverse transcription-PCR evidence for a toxT mRNA at times when ToxR-dependent transcription was no longer detectable by primer extension.

Ground motion modeling of the 1906 San Francisco earthquake II: Ground motion estimates for the 1906 earthquake and scenario events

DOE Office of Scientific and Technical Information (OSTI.GOV)

Aagaard, B; Brocher, T; Dreger, D

2007-02-09

We estimate the ground motions produced by the 1906 San Francisco earthquake making use of the recently developed Song et al. (2008) source model that combines the available geodetic and seismic observations and recently constructed 3D geologic and seismic velocity models. Our estimates of the ground motions for the 1906 earthquake are consistent across five ground-motion modeling groups employing different wave propagation codes and simulation domains. The simulations successfully reproduce the main features of the Boatwright and Bundock (2005) ShakeMap, but tend to over predict the intensity of shaking by 0.1-0.5 modified Mercalli intensity (MMI) units. Velocity waveforms at sitesmore » throughout the San Francisco Bay Area exhibit characteristics consistent with rupture directivity, local geologic conditions (e.g., sedimentary basins), and the large size of the event (e.g., durations of strong shaking lasting tens of seconds). We also compute ground motions for seven hypothetical scenarios rupturing the same extent of the northern San Andreas fault, considering three additional hypocenters and an additional, random distribution of slip. Rupture directivity exerts the strongest influence on the variations in shaking, although sedimentary basins do consistently contribute to the response in some locations, such as Santa Rosa, Livermore, and San Jose. These scenarios suggest that future large earthquakes on the northern San Andreas fault may subject the current San Francisco Bay urban area to stronger shaking than a repeat of the 1906 earthquake. Ruptures propagating southward towards San Francisco appear to expose more of the urban area to a given intensity level than do ruptures propagating northward.« less

Large-scale culture of a megakaryocytic progenitor cell line with a single-use bioreactor system.

PubMed

Nurhayati, Retno Wahyu; Ojima, Yoshihiro; Dohda, Takeaki; Kino-Oka, Masahiro

2018-03-01

The increasing application of regenerative medicine has generated a growing demand for stem cells and their derivatives. Single-use bioreactors offer an attractive platform for stem cell expansion owing to their scalability for large-scale production and feasibility of meeting clinical-grade standards. The current work evaluated the capacity of a single-use bioreactor system (1 L working volume) for expanding Meg01 cells, a megakaryocytic (MK) progenitor cell line. Oxygen supply was provided by surface aeration to minimize foaming and orbital shaking was used to promote oxygen transfer. Oxygen transfer rates (k L a) of shaking speeds 50, 100, and 125 rpm were estimated to be 0.39, 1.12, and 10.45 h -1 , respectively. Shaking speed was a critical factor for optimizing cell growth. At 50 rpm, Meg01 cells exhibited restricted growth due to insufficient mixing. A negative effect occurred when the shaking speed was increased to 125 rpm, likely caused by high hydrodynamic shear stress. The bioreactor culture achieved the highest growth profile when shaken at 100 rpm, achieving a total expansion rate up to 5.7-fold with a total cell number of 1.2 ± 0.2 × 10 9 cells L -1 . In addition, cells expanded using the bioreactor system could maintain their potency to differentiate following the MK lineage, as analyzed from specific surface protein and morphological similarity with the cells grown in the conventional culturing system. Our study reports the impact of operational variables such as shaking speed for growth profile and MK differentiation potential of a progenitor cell line in a single-use bioreactor. © 2017 American Institute of Chemical Engineers Biotechnol. Prog., 34:362-369, 2018. © 2017 American Institute of Chemical Engineers.

Revisiting Molecular Dynamics on a CPU/GPU system: Water Kernel and SHAKE Parallelization.

PubMed

Ruymgaart, A Peter; Elber, Ron

2012-11-13

We report Graphics Processing Unit (GPU) and Open-MP parallel implementations of water-specific force calculations and of bond constraints for use in Molecular Dynamics simulations. We focus on a typical laboratory computing-environment in which a CPU with a few cores is attached to a GPU. We discuss in detail the design of the code and we illustrate performance comparable to highly optimized codes such as GROMACS. Beside speed our code shows excellent energy conservation. Utilization of water-specific lists allows the efficient calculations of non-bonded interactions that include water molecules and results in a speed-up factor of more than 40 on the GPU compared to code optimized on a single CPU core for systems larger than 20,000 atoms. This is up four-fold from a factor of 10 reported in our initial GPU implementation that did not include a water-specific code. Another optimization is the implementation of constrained dynamics entirely on the GPU. The routine, which enforces constraints of all bonds, runs in parallel on multiple Open-MP cores or entirely on the GPU. It is based on Conjugate Gradient solution of the Lagrange multipliers (CG SHAKE). The GPU implementation is partially in double precision and requires no communication with the CPU during the execution of the SHAKE algorithm. The (parallel) implementation of SHAKE allows an increase of the time step to 2.0fs while maintaining excellent energy conservation. Interestingly, CG SHAKE is faster than the usual bond relaxation algorithm even on a single core if high accuracy is expected. The significant speedup of the optimized components transfers the computational bottleneck of the MD calculation to the reciprocal part of Particle Mesh Ewald (PME).

The Relationship between Cranial Structure, Biomechanical Performance and Ecological Diversity in Varanoid Lizards

PubMed Central

McCurry, Matthew R.; Mahony, Michael; Clausen, Phillip D.; Quayle, Michelle R.; Walmsley, Christopher W.; Jessop, Tim S.; Wroe, Stephen; Richards, Heather; McHenry, Colin R.

2015-01-01

Skull structure is intimately associated with feeding ability in vertebrates, both in terms of specific performance measures and general ecological characteristics. This study quantitatively assessed variation in the shape of the cranium and mandible in varanoid lizards, and its relationship to structural performance (von Mises strain) and interspecific differences in feeding ecology. Geometric morphometric and linear morphometric analyses were used to evaluate morphological differences, and finite element analysis was used to quantify variation in structural performance (strain during simulated biting, shaking and pulling). This data was then integrated with ecological classes compiled from relevant scientific literature on each species in order to establish structure-function relationships. Finite element modelling results showed that variation in cranial morphology resulted in large differences in the magnitudes and locations of strain in biting, shaking and pulling load cases. Gracile species such as Varanus salvadorii displayed high strain levels during shaking, especially in the areas between the orbits. All models exhibit less strain during pull back loading compared to shake loading, even though a larger force was applied (pull =30N, shake = 20N). Relationships were identified between the morphology, performance, and ecology. Species that did not feed on hard prey clustered in the gracile region of cranial morphospace and exhibited significantly higher levels of strain during biting (P = 0.0106). Species that fed on large prey clustered in the elongate area of mandible morphospace. This relationship differs from those that have been identified in other taxonomic groups such as crocodiles and mammals. This difference may be due to a combination of the open ‘space-frame’ structure of the varanoid lizard skull, and the ‘pull back’ behaviour that some species use for processing large prey. PMID:26106889

Reconstituting botulinum toxin drugs: shaking, stirring or what?

PubMed

Dressler, Dirk; Bigalke, Hans

2016-05-01

Most botulinum toxin (BT) drugs are stored as powders which need to be reconstituted with normal saline before clinical use. As botulinum neurotoxin (BNT), the therapeutically active ingredient, is a large double-stranded protein the process of reconstitution should be performed with special attention to mechanical stress applied. We wanted to test the mechanical stability of BNT during the reconstitution process. For this, 100 MU onabotulinumtoxinA (Botox(®), Irvine, CA, USA) was reconstituted with 2.0 ml of NaCl/H2O. Gentle reconstitution (GR) was performed with a 5 ml syringe, a 0.90 × 70 mm injection needle, one cycle of injection-aspiration-injection and two gentle shakes of the vial. Aggressive reconstitution (AR) was performed with a 5 ml syringe, a 0.40 × 40 mm injection needle, ten injection-aspiration-injection cycles and 30 s of continuous shaking of the vial. AR increased the time to paralysis in the mouse hemidiaphragm assay (HDA) from 72.0 ± 4.6 to 106.0 ± 16.0 min (*p = 0.002, two-tailed t test after Kolmogorov-Smirnova test with Lilliefors correction for normal distribution). Construction of a calibration curve revealed that the increase in the time to paralysis was correlated with a loss of potency of from 100 to 58 MU (-42 %). BT users should use large diameter injection needles for reconstitution, apply two or three injection-aspiration-injection cycles and, maybe, shake the vials a few times to rinse the entire glass wall. Aggressive reconstitution with small diameter needles, prolonged injection-aspiration-injection and violent shaking should be avoided.

Ground-motion modeling of the 1906 San Francisco Earthquake, part II: Ground-motion estimates for the 1906 earthquake and scenario events

USGS Publications Warehouse

Aagaard, Brad T.; Brocher, T.M.; Dolenc, D.; Dreger, D.; Graves, R.W.; Harmsen, S.; Hartzell, S.; Larsen, S.; McCandless, K.; Nilsson, S.; Petersson, N.A.; Rodgers, A.; Sjogreen, B.; Zoback, M.L.

2008-01-01

We estimate the ground motions produce by the 1906 San Francisco earthquake making use of the recently developed Song et al. (2008) source model that combines the available geodetic and seismic observations and recently constructed 3D geologic and seismic velocity models. Our estimates of the ground motions for the 1906 earthquake are consistent across five ground-motion modeling groups employing different wave propagation codes and simulation domains. The simulations successfully reproduce the main features of the Boatwright and Bundock (2005) ShakeMap, but tend to over predict the intensity of shaking by 0.1-0.5 modified Mercalli intensity (MMI) units. Velocity waveforms at sites throughout the San Francisco Bay Area exhibit characteristics consistent with rupture directivity, local geologic conditions (e.g., sedimentary basins), and the large size of the event (e.g., durations of strong shaking lasting tens of seconds). We also compute ground motions for seven hypothetical scenarios rupturing the same extent of the northern San Andreas fault, considering three additional hypocenters and an additional, random distribution of slip. Rupture directivity exerts the strongest influence on the variations in shaking, although sedimentary basins do consistently contribute to the response in some locations, such as Santa Rosa, Livermore, and San Jose. These scenarios suggest that future large earthquakes on the northern San Andreas fault may subject the current San Francisco Bay urban area to stronger shaking than a repeat of the 1906 earthquake. Ruptures propagating southward towards San Francisco appear to expose more of the urban area to a given intensity level than do ruptures propagating northward.

Leaching of Chalcopyrite with Thiobacillus ferrooxidans: Effect of Surfactants and Shaking

PubMed Central

Duncan, D. W.; Trussell, P. C.; Walden, C. C.

1964-01-01

The rate of leaching of chalcopyrite by Thiobacillus ferrooxidans has been greatly accelerated by using shaken flasks in place of stationary bottles or percolators. A further increase in rate and extent of leaching was obtained by the use of Tween 20, 40, 60, and 80, Triton X-100, Quaker TT 5386, and Hyamine 2389. Tween 20 was the most effective surfactant. No individual component of the Tween molecule was responsible for the improved leaching. The Tween-to-chalcopyrite ratio is more important than the Tween-to-medium ratio. The effect of the surfactants is probably due to increased contact between the mineral surface and the organism, and shaking provides the necessary oxygen. Rates and yields obtained by use of surfactants and shaking as aids to microbiological leaching approach those obtained with acidified erric sulfate leaching. PMID:14131359

Optimization of VFAs and ethanol production with waste sludge used as the denitrification carbon source.

PubMed

Guo, Liang; Zhang, Jiawen; Yin, Li; Zhao, Yangguo; Gao, Mengchun; She, Zonglian

2015-01-01

An acidification metabolite such as volatile fatty acids (VFAs) and ethanol could be used as denitrification carbon sources for solving the difficult problem of carbon source shortages and low nitrogen removal efficiency. A proper control of environmental factors could be essential for obtaining the optimal contents of VFAs and ethanol. In this study, suspended solids (SS), oxidation reduction potential (ORP) and shaking rate were chosen to investigate the interactive effects on VFAs and ethanol production with waste sludge. It was indicated that T-VFA yield could be enhanced at lower ORP and shaking rate. Changing the SS, ORP and shaking rate could influence the distribution of acetic, propionic, butyric, valeric acids and ethanol. The optimal conditions for VFAs and ethanol production used as a denitrification carbon source were predicted by analyzing response surface methodology (RSM).

Strain Rate and Stress Relaxation Effects on Pressuremeter Testing in Clays

DTIC Science & Technology

1992-03-01

CHARACTERISTICS OF KAOLINITE AND GROUND SILICA 245 APPENDIX E COMPUTER PROGRAMS ....................... 248 0 0 0 0 0 0 0 iv LIST OF TABLES Table Page 3.1 A...Comparison of Three Types of Boundary Conditions in a Multiaxial Cubical Test Apparatus ................... 37 3.2 Properties of the Kaolinite and Kaolin...to 0.01 %/min Versus Strain Rate for Kaolinite Clay ................... 102 4.3 Shear Strength Normalized with Respect to 0.01 %/min Versus Strain Rate

Preliminary orbital parallax catalog

NASA Technical Reports Server (NTRS)

Halliwell, M.

1981-01-01

The study is undertaken to calibrate the more reliable parallaxes derived from a comparison of visual and spectroscopic orbits and to encourage observational studies of other promising binaries. The methodological techniques used in computing orbital parallaxes are analyzed. Tables summarizing orbital data and derived system properties are then given. Also given is a series of detailed discussions of the 71 individual systems included in the tables. Data are listed for 57 other systems which are considered promising candidates for eventual orbital parallax determination.

The Clinical Development of Thalildomide as an Angiogenesis Inhibitor Therapy for Prostate Cancer

DTIC Science & Technology

2005-10-01

regulation of cell adhesion molecules LFA-1 and ICAM-1 after in vitro treatment with the anti- TNF - alpha agent thalidomide . Settles B, Stevenson A...Plasma levels of circulating TNF -α and VEGF measured in 16 thalidomide treated patients seemed to increase after treatment (Table 2). Serum levels of...Logothetis, Christopher J. Page 6 Table 2. Levels of circulating VEGF, bFGF, TNF -α and IL-6 before and after thalidomide treatment. Comparison of

Evaluation of Planning for Fish and Wildlife at Corps of Engineers Reservoirs, Eufaula Reservoir Project, Oklahoma.

DTIC Science & Technology

1982-09-01

Eufaula Lake, the largest body of water in Oklahoma, extends into McIntosh, Haskell, Pittsburg and Olwiulgee counties , Oklahoma. Construction of the...TABLES iv LIST OF FIGURES vii PROJECT PERSONNEL viii INTRODUCTION 1 Location I Authorization 1 Physical Features 3 Area Description 4 WILDLIFE RESULTS AND...TableLa I Eufaula Lake Project. Summary of pertinent physical 4 characteristics. 2 Eufaula Project. Comparison of terrestrial habitat 9 affected by

Active Control of Forward Swept Wings with Divergence and Flutter Aeroelastic Instabilities.

DTIC Science & Technology

1984-05-01

instability) the range of k needed for the Padd fitting begins at zero and increases until it encompasses the expected flutter frequency. At this...34But if any of you lacks wisdom, he should pray to God, who will give it to him; because God gives generously and graciously to all." (James 1:5) This...C-11 i-" \\*i List of Tables Table Page 1 Generalized Aerodynamic Influence Coefficient Comparisons For The Wing

Thermal Mechanical Fatigue Cracks Growth from Laser Drilled Holes in Single Crystal Material (Preprint)

DTIC Science & Technology

2012-03-01

temperature ranges, as well as with and without hot dwell periods. Table 4. Specimens chosen for SEM fractography . Samples ID Temperature variation...intersecting with crystallographic facet. Comparison with the fractography of the specimen (19776A) tested to %25.0 mechanical strain at the 800 F Figure... fractography of the specimen (19777B) tested to %4.0 mechanical strain (see Table 2). Large mechanical strain range generates large stresses around the hole

Intelligent modelling of bioprocesses: a comparison of structured and unstructured approaches.

PubMed

Hodgson, Benjamin J; Taylor, Christopher N; Ushio, Misti; Leigh, J R; Kalganova, Tatiana; Baganz, Frank

2004-12-01

This contribution moves in the direction of answering some general questions about the most effective and useful ways of modelling bioprocesses. We investigate the characteristics of models that are good at extrapolating. We trained three fully predictive models with different representational structures (differential equations, differential equations with inheritance of rates and a network of reactions) on Saccharopolyspora erythraea shake flask fermentation data using genetic programming. The models were then tested on unseen data outside the range of the training data and the resulting performances were compared. It was found that constrained models with mathematical forms analogous to internal mass balancing and stoichiometric relations were superior to flexible unconstrained models, even though no a priori knowledge of this fermentation was used.

Photoionization in the time and frequency domain

NASA Astrophysics Data System (ADS)

Isinger, M.; Squibb, R. J.; Busto, D.; Zhong, S.; Harth, A.; Kroon, D.; Nandi, S.; Arnold, C. L.; Miranda, M.; Dahlström, J. M.; Lindroth, E.; Feifel, R.; Gisselbrecht, M.; L'Huillier, A.

2017-11-01

Ultrafast processes in matter, such as the electron emission after light absorption, can now be studied using ultrashort light pulses of attosecond duration (10-18 seconds) in the extreme ultraviolet spectral range. The lack of spectral resolution due to the use of short light pulses has raised issues in the interpretation of the experimental results and the comparison with theoretical calculations. We determine photoionization time delays in neon atoms over a 40-electron volt energy range with an interferometric technique combining high temporal and spectral resolution. We spectrally disentangle direct ionization from ionization with shake-up, in which a second electron is left in an excited state, and obtain excellent agreement with theoretical calculations, thereby solving a puzzle raised by 7-year-old measurements.

Multiple ionization of neon by soft x-rays at ultrahigh intensity

NASA Astrophysics Data System (ADS)

Guichard, R.; Richter, M.; Rost, J.-M.; Saalmann, U.; Sorokin, A. A.; Tiedtke, K.

2013-08-01

At the free-electron laser FLASH, multiple ionization of neon atoms was quantitatively investigated at photon energies of 93.0 and 90.5 eV. For ion charge states up to 6+, we compare the respective absolute photoionization yields with results from a minimal model and an elaborate description including standard sequential and direct photoionization channels. Both approaches are based on rate equations and take into account a Gaussian spatial intensity distribution of the laser beam. From the comparison we conclude that photoionization up to a charge of 5+ can be described by the minimal model which we interpret as sequential photoionization assisted by electron shake-up processes. For higher charges, the experimental ionization yields systematically exceed the elaborate rate-based prediction.

Fatigue resistance criteria for fiber-reinforced composite structures. Final report, 1 Apr 1971-30 Sep 1974

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dvorak, G.J.

1974-10-01

The research effort was concentrated on metal matrix composites, such as the Al--B, Al--Be, Cu--W, and similar systems. It was found that in as- fabricated composites with soft matrices fatigue failure can be prevented if the composite shakes down during cyclic loading. The fatigue strength of heat- treated composites is affected by residual microstresses, but failure can be prevented if the total microstresses are kept within the respective fatigue limits (at 10 to the 7th power cycles) of the constituents. These criteria for prevention of fatigue failure in metal matrix composite systems were verified by extensive comparisons of theoretical predictionsmore » with available experimental results. (GRA)« less

Tables of nuclear cross sections for galactic cosmic rays: Absorption cross sections

NASA Technical Reports Server (NTRS)

Townsend, L. W.; Wilson, J. W.

1985-01-01

A simple but comprehensive theory of nuclear reactions is presented. Extensive tables of nucleon, deuteron, and heavy-ion absorption cross sections over a broad range of energies are generated for use in cosmic ray shielding studies. Numerous comparisons of the calculated values with available experimental data show agreement to within 3 percent for energies above 80 MeV/nucleon and within approximately 10 percent for energies as low as 30 MeV/nucleon. These tables represent the culmination of the development of the absorption cross section formalism and supersede the preliminary absorption cross sections published previously in NASA TN D-8107, NASA TP-2138, and NASA TM-84636.

[Possible Instrument Contamination in the Operating Room During Implantation of Knee and Hip Arthroplasty].

PubMed

Quint, U; Benen, T

2016-04-01

Integrated ventilation systems with low turbulence displacement flow (TAV) are generally legally required in the architectural structure of operating theatres. However, it seems that the instruments laid out on sterile covered tables do not have the best possible protection from bacteria. Within an operating theatre, different bacteria counts are possible on the instruments. This prospective controlled study was conducted to demonstrate the influence of instrument tables with integrated horizontal flow on contamination with pathogens in comparison with conventional tables. In an operating theatre (OT) with a ceiling legally appropriate for TAV (2.40 m × 1.20 m), microbiological samples were placed on a table with integrated TAV flow (n = 100) and on a conventional instrument table (n = 100). The routine qualification of the OT was on an ongoing basis and was in accordance with DIN 1946-4: 1999 standards (in accordance with DIN measurement of recovery time 1946-4: 12-2008). This corresponds to the OT of the room class Ib. The results show significant differences between the two tables. The bacteria count and the percentage of contamination were many times higher on the conventional table. It is important to understand that the instruments are not completely protected against contamination after opening the pack and during the operation. Remedial measures are possible to optimise the sterility the instrument table. Georg Thieme Verlag KG Stuttgart · New York.

Investigation on Suitability of Natural Fibre as Replacement Material for Table Tennis Blade

NASA Astrophysics Data System (ADS)

Arifin, A. M. T.; Fahrul Hassan, M.; Ismail, A. E.; Zulafif Rahim, M.; Rasidi Ibrahim, M.; Haq, R. H. Abdul; Rahman, M. N. A.; Yunos, M. Z.; Amin, M. H. M.

2017-08-01

This paper presents an investigation of suitability natural fibre as replacement material for table tennis blade, due to low cost, lightweight and apparently environmentally. Nowadays, natural fibre are one of the materials often used in replaced the main material on manufacturing sector, such as automotive, and construction. The objective of this study is to investigate and evaluate the suitability natural fiber materials to replace wood as a structure on table tennis blade. The mechanical properties of the different natural fibre material were examined, and correlated with characteristic of table tennis blade. The natural fibre selected for the study are kenaf (Hibiscus Cannabinus), jute, hemp, sisal (Agave Sisalana) and ramie. A further comparison was made with the corresponding properties of each type of natural fiber using Quality Function Deployment (QFD) and Theory of Inventive Problem Solving (TRIZ). TRIZ has been used to determine the most appropriate solution in producing table tennis blade. The results showed the most appropriate solution in producing table tennis blade using natural fibre is kenaf natural fibre. The selected on suitability natural fibre used as main structure on table tennis blade are based on the characteristics need for good performance of table tennis blade, such as energy absorption, lightweight, strength and hardness. Therefore, it shows an opportunity for replacing existing materials with a higher strength, lower cost alternative that is environmentally friendly.

Combining Real-Time Seismic and GPS Data for Earthquake Early Warning (Invited)

NASA Astrophysics Data System (ADS)

Boese, M.; Heaton, T. H.; Hudnut, K. W.

2013-12-01

Scientists at Caltech, UC Berkeley, the Univ. of SoCal, the Univ. of Washington, the US Geological Survey, and ETH Zurich have developed an earthquake early warning (EEW) demonstration system for California and the Pacific Northwest. To quickly determine the earthquake magnitude and location, 'ShakeAlert' currently processes and interprets real-time data-streams from ~400 seismic broadband and strong-motion stations within the California Integrated Seismic Network (CISN). Based on these parameters, the 'UserDisplay' software predicts and displays the arrival and intensity of shaking at a given user site. Real-time ShakeAlert feeds are currently shared with around 160 individuals, companies, and emergency response organizations to educate potential users about EEW and to identify needs and applications of EEW in a future operational warning system. Recently, scientists at the contributing institutions have started to develop algorithms for ShakeAlert that make use of high-rate real-time GPS data to improve the magnitude estimates for large earthquakes (M>6.5) and to determine slip distributions. Knowing the fault slip in (near) real-time is crucial for users relying on or operating distributed systems, such as for power, water or transportation, especially if these networks run close to or across large faults. As shown in an earlier study, slip information is also useful to predict (in a probabilistic sense) how far a fault rupture will propagate, thus enabling more robust probabilistic ground-motion predictions at distant locations. Finally, fault slip information is needed for tsunami warning, such as in the Cascadia subduction-zone. To handle extended fault-ruptures of large earthquakes in real-time, Caltech and USGS Pasadena are currently developing and testing a two-step procedure that combines seismic and geodetic data; in the first step, high-frequency strong-motion amplitudes are used to rapidly classify near-and far-source stations. Then, the location and extent of the 2D fault rupture is determined from comparison with pre-calculated generic and fault-specific templates ('FinDer' algorithm, Finite Fault Rupture Detector). In the second step, long-period dynamic displacement amplitudes from the GPS sites are back-projected onto this rupture line/plane to estimate the slip amplitudes ('GPSlip' algorithm). The corresponding back-projection relations were empirically derived from a suite of 3D waveform simulations. We are currently testing our approach in southern California (both real-time and offline), although not yet included in the current distribution of ShakeAlert. RTK/PPP(AR) solutions from the RTNet software at USGS Pasadena currently provide 1 Hz real-time position times series at ~100 GPS sensor locations. Output is in openly available in JSON format. We and UNAVCO have tested onsite (in-receiver) PPP(AR) processing using Trimble NetR9 receivers with RTX & GLONASS options enabled, of which Caltech has recently purchased 41 new units. These special GPS receivers will provide 5 Hz position and velocity streams. We will deliver the GPS RTX output (in GSOF format) into the EEW system (in Earthworm tracebuf2 format). The new receivers are to be installed at 'zipper array' stations of the SCSN in upcoming months. In addition, we have developed a framework for end-to-end offline testing with archived and simulated waveform data.

Investigation of Acidithiobacillus ferrooxidans in pure and mixed-species culture for bioleaching of Theisen sludge from former copper smelting.

PubMed

Klink, C; Eisen, S; Daus, B; Heim, J; Schlömann, M; Schopf, S

2016-06-01

The aim of this study was to investigate the potential of bioleaching for the treatment of an environmentally hazardous waste, a blast-furnace flue dust designated Theisen sludge. Bioleaching of Theisen sludge was investigated at acidic conditions with Acidithiobacillus ferrooxidans in pure and mixed-species culture with Acidiphilium. In shaking-flask experiments, bioleaching parameters (pH, redox potential, zinc extraction from ZnS, ferrous- and ferric-iron concentration) were controlled regularly. The analysis of the dissolved metals showed that 70% zinc and 45% copper were extracted. Investigations regarding the arsenic and antimony species were performed. When iron ions were lacking, animonate (Sb(V)) and total arsenic concentration were highest in solution. The bioleaching approach was scaled up in stirred-tank bioreactors resulting in higher leaching efficiency of valuable trace elements. Concentrations of dissolved antimony were approx. 23 times, and of cobalt, germanium, and rhenium three times higher in comparison to shaking-flask experiments, when considering the difference in solid load of Theisen sludge. The extraction of base and trace metals from Theisen sludge, despite of its high content of heavy metals and organic compounds, was feasible with iron-oxidizing acidophilic bacteria. In stirred-tank bioreactors, the mixed-species culture performed better. To the best of our knowledge, this study is the first providing an appropriate biological technology for the treatment of Theisen sludge to win valuable elements. © 2016 The Society for Applied Microbiology.

77 FR 462 - Regulation of Fuels and Fuel Additives: Identification of Additional Qualifying Renewable Fuel...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-01-05

... included in Table 1 for renewable diesel. Energy grasses: Based on our comparison of switchgrass and the..., representing at most a 6% change in the energy grass lifecycle impacts in comparison to the petroleum fuel... conversion of previously unfarmed land in other countries into cropland for energy grass-based renewable fuel...

Tree shaking machine aids cone collection in a Douglas-fir seed orchard.

Treesearch

Donald L. Copes; William K. Randall

1983-01-01

A boom-type tree shaker was used in a Douglas-fir seed orchard to remove cones from 7- to 9-meter tall grafted Douglas-fir trees. An average of 55 percent of the cones were removed by shaking, while damage inflicted to the upper crown was confined primarily to branch and leader breakage in the top three internodes. Damage to the lower bole, where the shaker head...

A new modified wetting test and an alternative disintegration test for orally disintegrating tablets.

PubMed

Hooper, Patrick; Lasher, Jason; Alexander, Kenneth S; Baki, Gabriella

2016-02-20

Industrial manufacturing of solid oral dosage forms require quality tests, such as friability, hardness, and disintegration. The United States Pharmacopeia (USP) disintegration test uses 900mL of water. However, recent studies of orally disintegrating tablets (ODTs) have shown that this volume does not accurately portray the oral environment. In our study, various tests were conducted with a more moderate amount of water that accurately resembles the oral environment. A simulated wetting test was performed to calculate the water absorption ratio. Results showed that wetting was comparable to disintegration. Although the wetting test worked for most types of ODTs, it had limitations that produced inaccurate results. This led to the use of a modified shaking water bath test. This test was found to work for all types of ODT products and was not subject to the limitations of the wetting test. The shake test could provide disintegration times rather than water permeation times; however, it could not be used to calculate the water absorption ratio. A strong correlation was observed between the standardized shake test and the USP disintegration times for the tablets. This shake test could be used during the development stages and quality tests for ODTs with relative ease. Copyright © 2015 Elsevier B.V. All rights reserved.

Prompt Assessment of Global Earthquakes for Response (PAGER): A System for Rapidly Determining the Impact of Earthquakes Worldwide

USGS Publications Warehouse

Earle, Paul S.; Wald, David J.; Jaiswal, Kishor S.; Allen, Trevor I.; Hearne, Michael G.; Marano, Kristin D.; Hotovec, Alicia J.; Fee, Jeremy

2009-01-01

Within minutes of a significant earthquake anywhere on the globe, the U.S. Geological Survey (USGS) Prompt Assessment of Global Earthquakes for Response (PAGER) system assesses its potential societal impact. PAGER automatically estimates the number of people exposed to severe ground shaking and the shaking intensity at affected cities. Accompanying maps of the epicentral region show the population distribution and estimated ground-shaking intensity. A regionally specific comment describes the inferred vulnerability of the regional building inventory and, when available, lists recent nearby earthquakes and their effects. PAGER's results are posted on the USGS Earthquake Program Web site (http://earthquake.usgs.gov/), consolidated in a concise one-page report, and sent in near real-time to emergency responders, government agencies, and the media. Both rapid and accurate results are obtained through manual and automatic updates of PAGER's content in the hours following significant earthquakes. These updates incorporate the most recent estimates of earthquake location, magnitude, faulting geometry, and first-hand accounts of shaking. PAGER relies on a rich set of earthquake analysis and assessment tools operated by the USGS and contributing Advanced National Seismic System (ANSS) regional networks. A focused research effort is underway to extend PAGER's near real-time capabilities beyond population exposure to quantitative estimates of fatalities, injuries, and displaced population.

Comments on potential geologic and seismic hazards affecting coastal Ventura County, California

USGS Publications Warehouse

Ross, Stephanie L.; Boore, David M.; Fisher, Michael A.; Frankel, Arthur D.; Geist, Eric L.; Hudnut, Kenneth W.; Kayen, Robert E.; Lee, Homa J.; Normark, William R.; Wong, Florence L.

2004-01-01

This report examines the regional seismic and geologic hazards that could affect proposed liquefied natural gas (LNG) facilities in coastal Ventura County, California. Faults throughout this area are thought to be capable of producing earthquakes of magnitude 6.5 to 7.5, which could produce surface fault offsets of as much as 15 feet. Many of these faults are sufficiently well understood to be included in the current generation of the National Seismic Hazard Maps; others may become candidates for inclusion in future revisions as research proceeds. Strong shaking is the primary hazard that causes damage from earthquakes and this area is zoned with a high level of shaking hazard. The estimated probability of a magnitude 6.5 or larger earthquake (comparable in size to the 2003 San Simeon quake) occurring in the next 30 years within 30 miles of Platform Grace is 50-60%; for Cabrillo Port, the estimate is a 35% likelihood. Combining these probabilities of earthquake occurrence with relationships that give expected ground motions yields the estimated seismic-shaking hazard. In parts of the project area, the estimated shaking hazard is as high as along the San Andreas Fault. The combination of long-period basin waves and LNG installations with large long-period resonances potentially increases this hazard.

Enhanced production of natural yellow pigments from Monascus purpureus by liquid culture: The relationship between fermentation conditions and mycelial morphology.

PubMed

Lv, Jun; Zhang, Bo-Bo; Liu, Xiao-Dong; Zhang, Chan; Chen, Lei; Xu, Gan-Rong; Cheung, Peter Chi Keung

2017-10-01

Natural yellow pigments produced by submerged fermentation of Monascus purpureus have potential economic value and application in the food industry. In the present study, the relationships among fermentation conditions (in terms of pH and shaking/agitation speed), mycelial morphology and the production of Monascus yellow pigments were investigated in both shake-flask and scale-up bioreactor experiments. In the shake-flask fermentation, the highest yield of the Monascus yellow pigments was obtained at pH 5.0 and a shaking speed of 180 rpm. Microscopic images revealed that these results were associated with the formation of freely dispersed small mycelial pellets with shorter, thicker and multi-branched hyphae. Further investigation indicated that the hyphal diameter was highly correlated with the biosynthesis of the Monascus yellow pigments. In a scaled-up fermentation experiment, the yield of yellow pigments (401 U) was obtained in a 200-L bioreactor, which is the highest yield to the best of our knowledge. The present findings can advance our knowledge on the conditions used for enhancing the production of Monascus yellow pigments in submerged fermentation and facilitate large-scale production of these natural pigments. Copyright © 2017 The Society for Biotechnology, Japan. Published by Elsevier B.V. All rights reserved.

[The maximum heart rate in the exercise test: the 220-age formula or Sheffield's table?].

PubMed

Mesquita, A; Trabulo, M; Mendes, M; Viana, J F; Seabra-Gomes, R

1996-02-01

To determine in the maximum cardiac rate in exercise test of apparently healthy individuals may be more properly estimated through 220-age formula (Astrand) or the Sheffield table. Retrospective analysis of clinical history and exercises test of apparently healthy individuals submitted to cardiac check-up. Sequential sampling of 170 healthy individuals submitted to cardiac check-up between April 1988 and September 1992. Comparison of maximum cardiac rate of individuals studied by the protocols of Bruce and modified Bruce, in interrupted exercise test by fatigue, and with the estimated values by the formulae: 220-age versus Sheffield table. The maximum cardiac heart rate is similar with both protocols. This parameter in normal individuals is better predicted by the 220-age formula. The theoretic maximum cardiac heart rate determined by 220-age formula should be recommended for a healthy, and for this reason the Sheffield table has been excluded from our clinical practice.

A New Generation of Los Alamos Opacity Tables

DOE PAGES

Colgan, James Patrick; Kilcrease, David Parker; Magee, Jr., Norman H.; ...

2016-01-26

We present a new, publicly available, set of Los Alamos OPLIB opacity tables for the elements hydrogen through zinc. Our tables are computed using the Los Alamos ATOMIC opacity and plasma modeling code, and make use of atomic structure calculations that use fine-structure detail for all the elements considered. Our equation-of-state (EOS) model, known as ChemEOS, is based on the minimization of free energy in a chemical picture and appears to be a reasonable and robust approach to determining atomic state populations over a wide range of temperatures and densities. In this paper we discuss in detail the calculations thatmore » we have performed for the 30 elements considered, and present some comparisons of our monochromatic opacities with measurements and other opacity codes. We also use our new opacity tables in solar modeling calculations and compare and contrast such modeling with previous work.« less

Mesoscale Convective Complex versus Non-Mesoscale Convective Complex Thunderstorms: A Comparison of Selected Meteorological Variables.

DTIC Science & Technology

1986-08-01

mean square errors for selected variables . . 34 8. Variable range and mean value for MCC and non-MCC cases . . 36 9. Alpha ( a ) levels at which the...Table 9. For each variable, the a level is listed at which the two mean values are determined to be significantly 38 Table 9. Alpha ( a ) levels at...vorticity advection None 700 mb vertical velocity forecast .20 different. These a levels express the probability of erroneously con- cluding that the

Epidemiological Surveillance of Influenza and Other Respiratory Diseases in Military Personnel. Prevention of Influenza and Other Respiratory Diseases - Laboratory Studies

DTIC Science & Technology

1987-06-30

of itself without any particular action. The number of positive throat cultures obtained each week are presented in Table 10. Strep - tococcal...number of individuals coming to the Clinic with URI symptoms and temperatures’C990 F is shown in the left hand column (Table 10). These numbers include...students. COMPARISON OF DIFFERENT TESTS FOR THE DIAGNOSIS OF INFLUENZA There were 15 students and 77 permanent party from whom we obtained throat

Military and Private Sector Commodity Outlets: A Retail Price Comparison

DTIC Science & Technology

1985-02-01

II where it is noted that some PXs carry only the glass bowl Sunbeam Mixmaser, at $69.95, while off-base outlets such as K-Mart carry the steel bowl...by comparing Table Bl with Tables B2 through B6. 11. The only difference between the two models is that the higher priced model included a glass ...Arrow Charcoal Briquets, 10 lb. Bag 9. Atra Shaving Cartridges, Pack of 10 10. Westinghouse Softlite Lightbulbs , 60 W, pack of 4 11. Kiwi Black Shoe

Estimating Differences in Area-Level Impacts of Various Recruiting Resources: Can Different Recruiting Areas and Years by Pooled?

DTIC Science & Technology

1983-08-01

Local Leads (Qualified and Interested) from LAMS Advertising (Based on FY82 Experience) Table 7 - Long Term Elasticities for Navy-Sourced NOIC Leads...Area Level Elasticities for Total NOIC Leads (Regardless of Source of Advertising ) for FY79, FY80 (FY80: 146,465) Appendix - Table la - Comparison of...of national .1*S leads (e.g., NOIC leads from a Navy source or from Joint DOD advertising (JADOR) sources), and for local leads. An Appendix

Project Ranch Hand II. An Epidemiologic Investigation of Health Effects in Air Force Personnel Following Exposure to Herbicides. Mortality Update - 1985.

DTIC Science & Technology

1985-11-29

Table 3 in the baseline report aind contains surrinary counts and death rates by occupation, race and group. In thp flecember IV4 report, the...these diminished death rates appear to be found in the Ranch Hand cffwcers borr, b.f(jre 1935, while Ranch Hand officers with later birth dates...death rate than their Comparisons. 12 - .*.*.s...-...*. -~~~. "... . .. . . .. . .. . .. . .... . ’N Table 14 Death Rates by Group, Rank, Occupation

A Comparison of Password Techniques

DTIC Science & Technology

1990-03-01

questions that had the lowest success rate dealt with an individual’s favorite restaurant, actor or actress , and choice of alternative profession. Two...ANY COUNTRY IN THE WORLD, WHICH WOULD IT BE? 74 71.0 WHAT IS THE LAST NAME OF YOUR FAVORITE ACTOR OR ACTRESS ? 60 58.3 40 TABLE 11 RESPONDENT MATCHING...COULD TRAVEL TO ANY COUNTRY IN THE WORLD, WHICH WOULD IT BE? 27 31.0 WHAT IS THE LAST NAME OF YOUR FAVORITE ACTOR OR ACTRESS ? 25 28.7 45 TABLE 14

A Field Visibility Comparison between Electroluminescent Sources and Standard U.S. Coast Guard Incandescent Aids-to-Navigation Sources.

DTIC Science & Technology

1982-10-01

this is critical. All buoy and many shore based systems employ back-up systems . In the case of buoys, 4 -when a lamp fails to emit, a new lamp is...88 LIST OF TABLES 1. Incandescent Source Table of Information -------------------- 38 2. Background Information on Subjects...functional aids-to-navigation system . The principal component of this system is the lighted aid which exists in many forms, from the wind and wave

Strong ground motions generated by earthquakes on creeping faults

USGS Publications Warehouse

Harris, Ruth A.; Abrahamson, Norman A.

2014-01-01

A tenet of earthquake science is that faults are locked in position until they abruptly slip during the sudden strain-relieving events that are earthquakes. Whereas it is expected that locked faults when they finally do slip will produce noticeable ground shaking, what is uncertain is how the ground shakes during earthquakes on creeping faults. Creeping faults are rare throughout much of the Earth's continental crust, but there is a group of them in the San Andreas fault system. Here we evaluate the strongest ground motions from the largest well-recorded earthquakes on creeping faults. We find that the peak ground motions generated by the creeping fault earthquakes are similar to the peak ground motions generated by earthquakes on locked faults. Our findings imply that buildings near creeping faults need to be designed to withstand the same level of shaking as those constructed near locked faults.

Economic impacts of the ShakeOut scenario

USGS Publications Warehouse

Rose, A.; Wei, D.; Wein, A.

2011-01-01

For the ShakeOut Earthquake Scenario, we estimate $68 billion in direct and indirect business interruption (BI) and $11 billion in related costs in addition to the $113 billion in property damage in an eight-county Southern California region. The modeled conduits of shock to the economy are property damage and lifeline service outages that affect the economy’s ability to produce. Property damage from fire is 50% greater than property damage from shaking because fire is more devastating. BI from water service disruption and fire each represent around one-third of total BI losses because of the long duration of service outage or long restoration and reconstruction periods. Total BI losses are 4.3% of annual gross output in the affected region, an impact far larger than most conventional economic recessions. These losses are still much lower than they potentially could be due to the resilience of the economy.

Nonlinear site response in medium magnitude earthquakes near Parkfield, California

USGS Publications Warehouse

Rubinstein, Justin L.

2011-01-01

Careful analysis of strong-motion recordings of 13 medium magnitude earthquakes (3.7 ≤ M ≤ 6.5) in the Parkfield, California, area shows that very modest levels of shaking (approximately 3.5% of the acceleration of gravity) can produce observable changes in site response. Specifically, I observe a drop and subsequent recovery of the resonant frequency at sites that are part of the USGS Parkfield dense seismograph array (UPSAR) and Turkey Flat array. While further work is necessary to fully eliminate other models, given that these frequency shifts correlate with the strength of shaking at the Turkey Flat array and only appear for the strongest shaking levels at UPSAR, the most plausible explanation for them is that they are a result of nonlinear site response. Assuming this to be true, the observation of nonlinear site response in small (M M 6.5 San Simeon earthquake and the 2004 M 6 Parkfield earthquake).

The ShakeOut Scenario

USGS Publications Warehouse

Jones, Lucile M.; Bernknopf, Richard; Cox, Dale; Goltz, James; Hudnut, Kenneth; Mileti, Dennis; Perry, Suzanne; Ponti, Daniel; Porter, Keith; Reichle, Michael; Seligson, Hope; Shoaf, Kimberley; Treiman, Jerry; Wein, Anne

2008-01-01

This is the initial publication of the results of a cooperative project to examine the implications of a major earthquake in southern California. The study comprised eight counties: Imperial, Kern, Los Angeles, Orange, Riverside, San Bernardino, San Diego, and Ventura. Its results will be used as the basis of an emergency response and preparedness exercise, the Great Southern California ShakeOut, and for this purpose we defined our earthquake as occurring at 10:00 a.m. on November 13, 2008. As members of the southern California community use the ShakeOut Scenario to plan and execute the exercise, we anticipate discussion and feedback. This community input will be used to refine our assessment and will lead to a formal publication in early 2009. Our goal in the ShakeOut Scenario is to identify the physical, social and economic consequences of a major earthquake in southern California and in so doing, enable the users of our results to identify what they can change now?before the earthquake?to avoid catastrophic impact after the inevitable earthquake occurs. To do so, we had to determine the physical damages (casualties and losses) caused by the earthquake and the impact of those damages on the region?s social and economic systems. To do this, we needed to know about the earthquake ground shaking and fault rupture. So we first constructed an earthquake, taking all available earthquake research information, from trenching and exposed evidence of prehistoric earthquakes, to analysis of instrumental recordings of large earthquakes and the latest theory in earthquake source physics. We modeled a magnitude (M) 7.8 earthquake on the southern San Andreas Fault, a plausible event on the fault most likely to produce a major earthquake. This information was then fed forward into the rest of the ShakeOut Scenario. The damage impacts of the scenario earthquake were estimated using both HAZUS-MH and expert opinion through 13 special studies and 6 expert panels, and fall into four categories: building damages, non-structural damages, damage to lifelines and infrastructure, and fire losses. The magnitude 7.8 ShakeOut earthquake is modeled to cause about 1800 deaths and $213 billion of economic losses. These numbers are as low as they are because of aggressive retrofitting programs that have increased the seismic resistance of buildings, highways and lifelines, and economic resiliency. These numbers are as large as they are because much more retrofitting could still be done. The earthquake modeled here may never happen. Big earthquakes on the San Andreas Fault are inevitable, and by geologic standards extremely common, but probably will not be exactly like this one. The next very damaging earthquake could easily be on another fault. However, lessons learned from this particular event apply to many other events and could provide benefits in many possible future events.

Behavior of braced excavation in sand under a seismic condition: experimental and numerical studies

NASA Astrophysics Data System (ADS)

Konai, Sanku; Sengupta, Aniruddha; Deb, Kousik

2018-04-01

The behavior of braced excavation in dry sand under a seismic condition is investigated in this paper. A series of shake table tests on a reduced scale model of a retaining wall with one level of bracing were conducted to study the effect of different design parameters such as excavation depth, acceleration amplitude and wall stiffness. Numerical analyses using FLAC 2D were also performed considering one level of bracing. The strut forces, lateral displacements and bending moments in the wall at the end of earthquake motion were compared with experimental results. The study showed that in a post-seismic condition, when other factors were constant, lateral displacement, bending moment, strut forces and maximum ground surface displacement increased with excavation depth and the amplitude of base acceleration. The study also showed that as wall stiffness decreased, the lateral displacement of the wall and ground surface displacement increased, but the bending moment of the wall and strut forces decreased. The net earth pressure behind the walls was influenced by excavation depth and the peak acceleration amplitude, but did not change significantly with wall stiffness. Strut force was the least affected parameter when compared with others under a seismic condition.

Experimental investigation of jet pulse control on flexible vibrating structures

NASA Astrophysics Data System (ADS)

Karaiskos, Grigorios; Papanicolaou, Panos; Zacharopoulos, Dimitrios

2016-08-01

The feasibility of applying on-line fluid jet pulses to actively control the vibrations of flexible structures subjected to harmonic and earthquake-like base excitations provided by a shake table is explored. The operating principles and capabilities of the control system applied have been investigated in a simplified small-scale laboratory model that is a mass attached at the top free end of a vertical flexible slender beam with rectangular cross-section, the other end of which is mounted on an electrodynamic shaker. A pair of opposite jets placed on the mass at the top of the cantilever beam applied the appropriate forces by ejecting pressurized air pulses controlled by on/off solenoid electro-valves via in house developed control software, in order to control the vibration caused by harmonic, periodic and random excitations at pre-selected frequency content provided by the shaker. The dynamics of the structure was monitored by accelerometers and the jet impulses by pressure sensors. The experimental results have demonstrated the effectiveness and reliability of Jet Pulse Control Systems (JPCS). It was verified that the measured root mean square (RMS) vibration levels of the controlled structure from harmonic and earthquake base excitations, could be reduced by approximately 50% and 33% respectively.

Failure behavior of concrete pile and super-structure dynamic response as a result of soil liquefaction during earthquake

NASA Astrophysics Data System (ADS)

Kaneda, Shogo; Hayashi, Kazuhiro; Hachimori, Wataru; Tamura, Shuji; Saito, Taiki

2017-10-01

In past earthquake disasters, numerous building structure piles were damaged by soil liquefaction occurring during the earthquake. Damage to these piles, because they are underground, is difficult to find. The authors aim to develop a monitoring method of pile damage based on superstructure dynamic response. This paper investigated the relationship between the damage of large cross section cementitious piles and the dynamic response of the super structure using a centrifuge test apparatus. A dynamic specimen used simple cross section pile models consisting of aluminum rod and mortar, a saturated soil (Toyoura sand) of a relative density of 40% and a super structure model of a natural period of 0.63sec. In the shaking table test under a 50G field (length scale of 1/50), excitation was a total of 3 motions scaled from the Rinkai wave at different amplitudes. The maximum acceleration of each of the excitations was 602gal, 336gal and 299gal. The centrifuge test demonstrated the liquefaction of saturated soil and the failure behavior of piles. In the test result, the damage of piles affected the predominant period of acceleration response spectrum on the footing of the superstructure.

Online Wavelet Complementary velocity Estimator.

PubMed

Righettini, Paolo; Strada, Roberto; KhademOlama, Ehsan; Valilou, Shirin

2018-02-01

In this paper, we have proposed a new online Wavelet Complementary velocity Estimator (WCE) over position and acceleration data gathered from an electro hydraulic servo shaking table. This is a batch estimator type that is based on the wavelet filter banks which extract the high and low resolution of data. The proposed complementary estimator combines these two resolutions of velocities which acquired from numerical differentiation and integration of the position and acceleration sensors by considering a fixed moving horizon window as input to wavelet filter. Because of using wavelet filters, it can be implemented in a parallel procedure. By this method the numerical velocity is estimated without having high noise of differentiators, integration drifting bias and with less delay which is suitable for active vibration control in high precision Mechatronics systems by Direct Velocity Feedback (DVF) methods. This method allows us to make velocity sensors with less mechanically moving parts which makes it suitable for fast miniature structures. We have compared this method with Kalman and Butterworth filters over stability, delay and benchmarked them by their long time velocity integration for getting back the initial position data. Copyright © 2017 ISA. Published by Elsevier Ltd. All rights reserved.

Combined state and parameter identification of nonlinear structural dynamical systems based on Rao-Blackwellization and Markov chain Monte Carlo simulations

NASA Astrophysics Data System (ADS)

Abhinav, S.; Manohar, C. S.

2018-03-01

The problem of combined state and parameter estimation in nonlinear state space models, based on Bayesian filtering methods, is considered. A novel approach, which combines Rao-Blackwellized particle filters for state estimation with Markov chain Monte Carlo (MCMC) simulations for parameter identification, is proposed. In order to ensure successful performance of the MCMC samplers, in situations involving large amount of dynamic measurement data and (or) low measurement noise, the study employs a modified measurement model combined with an importance sampling based correction. The parameters of the process noise covariance matrix are also included as quantities to be identified. The study employs the Rao-Blackwellization step at two stages: one, associated with the state estimation problem in the particle filtering step, and, secondly, in the evaluation of the ratio of likelihoods in the MCMC run. The satisfactory performance of the proposed method is illustrated on three dynamical systems: (a) a computational model of a nonlinear beam-moving oscillator system, (b) a laboratory scale beam traversed by a loaded trolley, and (c) an earthquake shake table study on a bending-torsion coupled nonlinear frame subjected to uniaxial support motion.

Modeling of a viscoelastic damper and its application in structural control

PubMed Central

Ibrahim, Zainah; Ghodsi, S. S.; Khatibi, Hamed

2017-01-01

Conventional seismic rehabilitation methods may not be suitable for some buildings owing to their high cost and time-consuming foundation work. In recent years, viscoelastic dampers (VEDs) have been widely used in many mid- and high-rise buildings. This study introduces a viscoelastic passive control system called rotary rubber braced damper (RRBD). The RRBD is an economical, lightweight, and easy-to-assemble device. A finite element model considering nonlinearity, large deformation, and material damage is developed to conduct a parametric study on different damper sizes under pushover cyclic loading. The fundamental characteristics of this VED system are clarified by analyzing building structures under cyclic loading. The result show excellent energy absorption and stable hysteresis loops in all specimens. Additionally, by using a sinusoidal shaking table test, the effectiveness of the RRBD to manage the response displacement and acceleration of steel frames is considered. The RRBD functioned at early stages of lateral displacement, indicating that the system is effective for all levels of vibration. Moreover, the proposed damper shows significantly better performance in terms of the column compression force resulting from the brace action compared to chevron bracing (CB). PMID:28570657

Seismic Response of Steel Braced Building Frame Considering Soil Structure Interaction (SSI): An Experimental Study

NASA Astrophysics Data System (ADS)

Hirave, Vivek; Kalyanshetti, Mahesh

2018-02-01

Conventional fixed-base analysis ignoring the effect of soil-flexibility may result in unsafe design. Therefore, to evaluate the realistic behavior of structure the soil structure interaction (SSI) effect shall be incorporated in the analysis. In seismic analysis, provision of bracing system is one of the important option for the structure to have sufficient strength with adequate stiffness to resist lateral forces. The different configuration of these bracing systems alters the response of buildings, and therefore, it is important to evaluate the most effective bracing systems in view point of stability against SSI effect. In present study, three RC building frames, G+3, G+5 and G+7 and their respective scaled down steel model with two types of steel bracing system incorporating the effect of soil flexibility is considered for experimental and analytical study. The analytical study is carried out using Elastic continuum approach and the experimental study is carried out using Shake Table. The influence of SSI on various seismic parameters is presented. The study reveals that, steel bracing system is beneficial to control SSI effect and it is observed that V bracing is more effective, in resisting seismic load considering SSI.

Feasibility study of tuned liquid column damper for ocean wave energy extraction

NASA Astrophysics Data System (ADS)

Wong, Yihong; King, Yeong-Jin; Lai, An-Chow; Chong, Kok-Keong; Lim, Boon-Han

2017-04-01

Intermittent nature and low efficiency are the major issues in renewable energy supply. To overcome these issues, one of the possible methods is through a hybrid system where multiple sources of renewable energy are combined to compensate each other's weaknesses. The hybrid of solar energy and wave energy becomes possible through the introduction of a stable floating platform which enables solar energy generation above it and wave energy harvesting underneath it. This paper is intended to study the feasibility of harnessing ocean wave energy using a tuned liquid column damper (TLCD), a type of passive damping device that is designed to suppress externally induced vibration force at a specific frequency range. The proposed TLCD is to be implemented within a floating offshore structure to serve as a vibration mitigating mechanism by reducing the dynamic response of the structure and simultaneously utilize the flowing motion of liquid within the TLCD for generating electricity. The constructed TLCD prototype is tuned according to theoretical study and tested using a shaking table with a predetermined frequency range. The oscillating motion of water within the TLCD and the potential of installation of hydro turbine generator in term of recoverable amount of energy are studied.

Ground simulation of wide frequency band angular vibration for Lander's optic sensors

NASA Astrophysics Data System (ADS)

Xing, Zhigang; Xiang, Jianwei; Zheng, Gangtie

2017-11-01

To guide a lander of Moon or Mars exploration spacecraft during the stage of descent onto a desired place, optic sensors have been chosen to take the task, which include optic cameras and laser distance meters. However, such optic sensors are sensitive to vibrations, especially angular vibrations, from the lander. To reduce the risk of abnormal function and ensure the performance of optic sensors, ground simulations are necessary. More importantly, the simulations can be used as a method for examining the sensor performance and finding possible improvement on the sensor design. In the present paper, we proposed an angular vibration simulation method during the landing. This simulation method has been realized into product and applied to optic sensor tests for the moon lander. This simulator can generate random angular vibration in a frequency range from 0 to 2000Hz, the control precision is +/-1dB, and the linear translational speed can be set to the required descent speed. The operation and data processing methods of this developed simulator are the same as a normal shake table. The analysis and design methods are studied in the present paper, and test results are also provided.

Key comparison of liquid density standards

NASA Astrophysics Data System (ADS)

Buchner, Christian; Zelenka, Zoltan; Kajastie, Heikki; Madec, Tanguy; Wolf, Henning; Vámossy, Csilla; Lorefice, Salvatore; Garberg, Torgunn; Lenard, Elżbieta; Spohr, Isabel; Mares, Gabriela; Spurný, Robert; Lumbreras, Angel; Medina, Nieves; Y Akçadağ, Ümit; Perkin, Michael

2015-01-01

Hydrostatic density determination for liquids is mainly performed by laboratories to provide means for calibrating liquid density measuring instruments such as oscillation-type density meters. From 2002 to 2005 the CIPM key comparison CCM.D-K2 'comparison of liquid density standards' was carried out piloted by the PTB. The aim was to compare the results of the density determination by the participating laboratories to support entries to the CMC tables in this sub-field. To provide further laboratories the possibility to support their entries to the CMC tables at the meeting of the EUROMET Working Group on Density in 2007 this comparison was agreed on. BEV (Austria) organized the comparison supported by the PTB (Germany). For the comparison samples of pentadecane, water, tetrachloroethylene and of an oil of high viscosity were measured in the temperature range from 5 °C to 60 °C at atmospheric pressure by hydrostatic weighing. The measurements were completed in 2008. The reference values of the first reports based on the draft of the CCM.D-K2. After the official publication of the CCM.D-K2 the reference values were recalculated and the report was finalised in 2015. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

As Compared to What? Characteristics of the AACSB Institutions That Utilize the Major Field Test in Business

ERIC Educational Resources Information Center

Bielinska-Kwapisz, Agnieszka; Brown, F. William

2014-01-01

The publishers of the Major Field Test in Business (MFT-B), an assessment of learning instrument, provide a list of institutions utilizing the instrument and a table that allows for comparison of local MFT-B mean scores to those of other institutions. The absence of information regarding the comparison group's characteristics limits the validity…

Outer crust of nonaccreting cold neutron stars

NASA Astrophysics Data System (ADS)

Rüster, Stefan B.; Hempel, Matthias; Schaffner-Bielich, Jürgen

2006-03-01

The properties of the outer crust of nonaccreting cold neutron stars are studied by using modern nuclear data and theoretical mass tables, updating in particular the classic work of Baym, Pethick, and Sutherland. Experimental data from the atomic mass table from Audi, Wapstra, and Thibault of 2003 are used and a thorough comparison of many modern theoretical nuclear models, both relativistic and nonrelativistic, is performed for the first time. In addition, the influences of pairing and deformation are investigated. State-of-the-art theoretical nuclear mass tables are compared to check their differences concerning the neutron drip line, magic neutron numbers, the equation of state, and the sequence of neutron-rich nuclei up to the drip line in the outer crust of nonaccreting cold neutron stars.

Preliminary Estimates of the Possibilities for Developing a Deployable Greenhouse for a Planetary Surface (Mars)

NASA Technical Reports Server (NTRS)

Rygalov, V. Y.; Bucklin, R. A.; Fowler, P. A.; Wheeler, R. M.

2000-01-01

Two of the main conditions for plant growth and development on the Martian surface are irradiation (optimal range from 80 W/sq m to 180 W/sq m of photosynthetically active radiation) and temperature (optimal range from 20 C to 27 C). The only known natural source of energy on Mars is sunlight, with a general intensity of 589 +/- 142 W/sq m (Martian Solar Constant). Comparisons of plant growth requirements with conditions on the Martian surface are presented in Table 1, while some basic considerations for implementing plant growth in a Martian DG are presented in Table 2. The general scenario and approximate schedule of startup and development of operations in DG are shown in Table 3.

Upper Mississippi embayment shallow seismic velocities measured in situ

USGS Publications Warehouse

Liu, Huaibao P.; Hu, Y.; Dorman, J.; Chang, T.-S.; Chiu, J.-M.

1997-01-01

Vertical seismic compressional- and shear-wave (P- and S-wave) profiles were collected from three shallow boreholes in sediment of the upper Mississippi embayment. The site of the 60-m hole at Shelby Forest, Tennessee, is on bluffs forming the eastern edge of the Mississippi alluvial plain. The bluffs are composed of Pleistocene loess, Pliocene-Pleistocene alluvial clay and sand deposits, and Tertiary deltaic-marine sediment. The 36-m hole at Marked Tree, Arkansas, and the 27-m hole at Risco, Missouri, are in Holocene Mississippi river floodplain sand, silt, and gravel deposits. At each site, impulsive P- and S-waves were generated by man-made sources at the surface while a three-component geophone was locked downhole at 0.91-m intervals. Consistent with their very similar geology, the two floodplain locations have nearly identical S-wave velocity (VS) profiles. The lowest VS values are about 130 m s-1, and the highest values are about 300 m s-1 at these sites. The shear-wave velocity profile at Shelby Forest is very similar within the Pleistocene loess (12m thick); in deeper, older material, VS exceeds 400 m s-1. At Marked Tree, and at Risco, the compressional-wave velocity (VP) values above the water table are as low as about 230 m s-1, and rise to about 1.9 km s-1 below the water table. At Shelby Forest, VP values in the unsaturated loess are as low as 302 m s-1. VP values below the water table are about 1.8 km s-1. For the two floodplain sites, the VP/VS ratio increases rapidly across the water table depth. For the Shelby Forest site, the largest increase in the VP/VS ratio occurs at ???20-m depth, the boundary between the Pliocene-Pleistocene clay and sand deposits and the Eocene shallow-marine clay and silt deposits. Until recently, seismic velocity data for the embayment basin came from earthquake studies, crustal-scale seismic refraction and reflection profiles, sonic logs, and from analysis of dispersed earthquake surface waves. Since 1991, seismic data for shallow sediment obtained from reflection, refraction, crosshole and downhole techniques have been obtained for sites at the northern end of the embayment basin. The present borehole data, however, are measured from sites representative of large areas in the Mississippi embayment. Therefore, they fill a gap in information needed for modeling the response of the embayment to destructive seismic shaking.

Performance of Subsurface Tube Drainage System in Saline Soils: A Case Study

NASA Astrophysics Data System (ADS)

Pali, A. K.

2015-06-01

In order to improve the saline and water logged soils caused due to groundwater table rise, installation of subsurface drainage system is considered as one of the best remedies. However, the design of the drainage system has to be accurate so that the field performance results conform to the designed results. In this investigation, the field performance of subsurface tube drainage system installed at the study area was evaluated. The performance was evaluated on the basis of comparison of the designed value of water table drop as 30 cm after 2 days of drainage and predicted and field measured hydraulic heads for a consecutive drainage period of 14 days. The investigation revealed that the actual drop of water table after 2 days of drainage was 25 cm, about 17 % less than the designed value of 30 cm after 2 days of drainage. The comparison of hydraulic heads predicted by Van Schilfgaarde equation of unsteady drainage with the field-measured hydraulic heads showed that the deviation of predicted hydraulic heads varied within a range of ±8 % indicating high acceptability of Van Schlifgaarde equation for designing subsurface drainage system in saline and water logged soils resembling to that of the study area.

As-built design specification for MISMAP

NASA Technical Reports Server (NTRS)

Brown, P. M.; Cheng, D. E.; Tompkins, M. A. (Principal Investigator)

1981-01-01

The MISMAP program, which is part of the CLASFYT package, is described. The program is designed to compare classification values with ground truth values for a segment and produce a comparison map and summary table.

DUMPING COOLED MOLDS FROM THE SHAKE OUT RAILS ONTO A ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

DUMPING COOLED MOLDS FROM THE SHAKE OUT RAILS ONTO A VIBRATING CONVEYOR WHICH TRANSPORTS CASTINGS AND SAND TO A SEPARATION SCREEN WHICH SIFTS SAND ONTO BELT CONVEYORS BELOW THAT CARRY IT PAST SWITCH-ACTIVATED WATER INJECTORS TO SIMILAR SWITCH-ACTIVATED FRESH SAND ADDERS BEFORE TRANSPORTING IT TO THE SAND STORAGE BIN WHILE CASTINGS ARE EITHER MANUALLY OR SMALL CRANE LIFTED TO DEGATING AREAS. - Southern Ductile Casting Company, Centerville Foundry, 101 Airport Road, Centreville, Bibb County, AL

Removal of iron and manganese using granular activated carbon and zeolite in artificial barrier of riverbank filtration

NASA Astrophysics Data System (ADS)

Ismail, Abustan; Harmuni, Halim; Mohd, Remy Rozainy M. A. Z.

2017-04-01

Iron and Manganese was examined from riverbank filtration (RBF) and river water in Sungai Kerian, Lubok Buntar, Serdang Kedah. Water from the RBF was influenced by geochemical and hydro chemical processes in the aquifer that made concentrations of iron (Fe), and manganese (Mn) high, and exceeded the standard values set by the Malaysia Ministry of Health. Therefore, in order to overcome the problem, the artificial barrier was proposed to improve the performance of the RBF. In this study, the capability and performance of granular activated carbon, zeolite and sand were investigated in this research. The effects of dosage, shaking speed, pH and contact time on removal of iron and manganese were studied to determine the best performance. For the removal of iron using granular activated carbon (GAC) and zeolite, the optimum contact time was at 2 hours with 200rpm shaking speed with 5g and 10g at pH 5 with percentage removal of iron was 87.81% and 83.20% respectively. The removal of manganese and zeolite arose sharply in 75 minutes with 90.21% removal, with 100rpm shaking speed. The GAC gave the best performance with 99.39% removal of manganese. The highest removal of manganese was achieved when the adsorbent dosage increased to 10g with shaking speed of 200rpm.

Development of piezoelectric bistable energy harvester based on buckled beam with axially constrained end condition for human motion

NASA Astrophysics Data System (ADS)

Eltanany, Ali M.; Yoshimura, Takeshi; Fujimura, Norifumi; Ebied, Mohamed R.; Ali, Mohamed G. S.

2017-10-01

In this study, we aim to examine the triggering force for an efficient snap-through solution of hand shaking vibrations of a piezoelectric bistable energy harvester. The proposed structure works at very low frequencies with nearly continuous periodic vibrations. The static characterizations are presented as well as the dynamic characterizations based on the phase diagrams of velocity vs displacement, voltage vs displacement, and voltage vs input acceleration. The mass attached to the bistable harvester plays an important role in determining the acceleration needed for the snap-through action, and the explanation for this role is complex because of mass dependence on frequency/amplitude vibration. Various hand shaking vibration tests are performed to demonstrate the advantage of the proposed structure in harvesting energy from hand shaking vibration. The minimum input acceleration for snap-through action was 11.59 m/s2 with peaks of 15.76 and 2 m/s2 in the frequency range of 1.3-2.7 Hz, when an attached mass of 14.6 g is used. The maximum generated power at a buckling state of 0.5 mm is 11.3 µW for the test structure at 26 g. The experimental results obtained in this study indicate that power output harvesting of slow hand shaking vibrations at 10 µW and a load resistance of 1 MΩ.

Earthquake shaking hazard estimates and exposure changes in the conterminous United States

USGS Publications Warehouse

Jaiswal, Kishor S.; Petersen, Mark D.; Rukstales, Kenneth S.; Leith, William S.

2015-01-01

A large portion of the population of the United States lives in areas vulnerable to earthquake hazards. This investigation aims to quantify population and infrastructure exposure within the conterminous U.S. that are subjected to varying levels of earthquake ground motions by systematically analyzing the last four cycles of the U.S. Geological Survey's (USGS) National Seismic Hazard Models (published in 1996, 2002, 2008 and 2014). Using the 2013 LandScan data, we estimate the numbers of people who are exposed to potentially damaging ground motions (peak ground accelerations at or above 0.1g). At least 28 million (~9% of the total population) may experience 0.1g level of shaking at relatively frequent intervals (annual rate of 1 in 72 years or 50% probability of exceedance (PE) in 50 years), 57 million (~18% of the total population) may experience this level of shaking at moderately frequent intervals (annual rate of 1 in 475 years or 10% PE in 50 years), and 143 million (~46% of the total population) may experience such shaking at relatively infrequent intervals (annual rate of 1 in 2,475 years or 2% PE in 50 years). We also show that there is a significant number of critical infrastructure facilities located in high earthquake-hazard areas (Modified Mercalli Intensity ≥ VII with moderately frequent recurrence interval).

USGS approach to real-time estimation of earthquake-triggered ground failure - Results of 2015 workshop

USGS Publications Warehouse

Allstadt, Kate E.; Thompson, Eric M.; Wald, David J.; Hamburger, Michael W.; Godt, Jonathan W.; Knudsen, Keith L.; Jibson, Randall W.; Jessee, M. Anna; Zhu, Jing; Hearne, Michael; Baise, Laurie G.; Tanyas, Hakan; Marano, Kristin D.

2016-03-30

The U.S. Geological Survey (USGS) Earthquake Hazards and Landslide Hazards Programs are developing plans to add quantitative hazard assessments of earthquake-triggered landsliding and liquefaction to existing real-time earthquake products (ShakeMap, ShakeCast, PAGER) using open and readily available methodologies and products. To date, prototype global statistical models have been developed and are being refined, improved, and tested. These models are a good foundation, but much work remains to achieve robust and defensible models that meet the needs of end users. In order to establish an implementation plan and identify research priorities, the USGS convened a workshop in Golden, Colorado, in October 2015. This document summarizes current (as of early 2016) capabilities, research and operational priorities, and plans for further studies that were established at this workshop. Specific priorities established during the meeting include (1) developing a suite of alternative models; (2) making use of higher resolution and higher quality data where possible; (3) incorporating newer global and regional datasets and inventories; (4) reducing barriers to accessing inventory datasets; (5) developing methods for using inconsistent or incomplete datasets in aggregate; (6) developing standardized model testing and evaluation methods; (7) improving ShakeMap shaking estimates, particularly as relevant to ground failure, such as including topographic amplification and accounting for spatial variability; and (8) developing vulnerability functions for loss estimates.

Quantification of social contributions to earthquake mortality

NASA Astrophysics Data System (ADS)

Main, I. G.; NicBhloscaidh, M.; McCloskey, J.; Pelling, M.; Naylor, M.

2013-12-01

Death tolls in earthquakes, which continue to grow rapidly, are the result of complex interactions between physical effects, such as strong shaking, and the resilience of exposed populations and supporting critical infrastructures and institutions. While it is clear that the social context in which the earthquake occurs has a strong effect on the outcome, the influence of this context can only be exposed if we first decouple, as much as we can, the physical causes of mortality from our consideration. (Our modelling assumes that building resilience to shaking is a social factor governed by national wealth, legislation and enforcement and governance leading to reduced levels of corruption.) Here we attempt to remove these causes by statistically modelling published mortality, shaking intensity and population exposure data; unexplained variance from this physical model illuminates the contribution of socio-economic factors to increasing earthquake mortality. We find that this variance partitions countries in terms of basic socio-economic measures and allows the definition of a national vulnerability index identifying both anomalously resilient and anomalously vulnerable countries. In many cases resilience is well correlated with GDP; people in the richest countries are unsurprisingly safe from even the worst shaking. However some low-GDP countries rival even the richest in resilience, showing that relatively low cost interventions can have a positive impact on earthquake resilience and that social learning between these countries might facilitate resilience building in the absence of expensive engineering interventions.

Application of an Online-Biomass Sensor in an Optical Multisensory Platform Prototype for Growth Monitoring of Biotechnical Relevant Microorganism and Cell Lines in Single-Use Shake Flasks

PubMed Central

Ude, Christian; Schmidt-Hager, Jörg; Findeis, Michael; John, Gernot Thomas; Scheper, Thomas; Beutel, Sascha

2014-01-01

In the context of this work we evaluated a multisensory, noninvasive prototype platform for shake flask cultivations by monitoring three basic parameters (pH, pO2 and biomass). The focus lies on the evaluation of the biomass sensor based on backward light scattering. The application spectrum was expanded to four new organisms in addition to E. coli K12 and S. cerevisiae [1]. It could be shown that the sensor is appropriate for a wide range of standard microorganisms, e.g., L. zeae, K. pastoris, A. niger and CHO-K1. The biomass sensor signal could successfully be correlated and calibrated with well-known measurement methods like OD600, cell dry weight (CDW) and cell concentration. Logarithmic and Bleasdale-Nelder derived functions were adequate for data fitting. Measurements at low cell concentrations proved to be critical in terms of a high signal to noise ratio, but the integration of a custom made light shade in the shake flask improved these measurements significantly. This sensor based measurement method has a high potential to initiate a new generation of online bioprocess monitoring. Metabolic studies will particularly benefit from the multisensory data acquisition. The sensor is already used in labscale experiments for shake flask cultivations. PMID:25232914