Large area sheet task: Advanced Dendritic Web Growth Development

NASA Technical Reports Server (NTRS)

Duncan, C. S.; Seidensticker, R. G.; Mchugh, J. P.; Hopkins, R. H.; Meier, D.; Schruben, J.

1981-01-01

A melt level control system was implemented to provide stepless silicon feed rates from zero to rates exactly matching the silicon consumed during web growth. Bench tests of the unit were successfully completed and the system mounted in a web furnace for operational verification. Tests of long term temperature drift correction techniques were made; web width monitoring seems most appropriate for feedback purposes. A system to program the initiation of the web growth cycle was successfully tested. A low cost temperature controller was tested which functions as well as units four times as expensive.

Detailed Sections from Auger Holes in the Roanoke Rapids 1:100,000 Map Sheet, North Carolina

USGS Publications Warehouse

Weems, Robert E.; Lewis, William C.

2007-01-01

Introduction The Roanoke Rapids 1:100,000 map sheet straddles the Coastal Plain / Piedmont boundary in northernmost North Carolina (Figure 1). Sediments of the Coastal Plain underlie the eastern three-fourths of this area, and patchy outliers of Coastal Plain units cap many of the higher hills in the western one-fourth of the area. Sediments dip gently to the east and reach a maximum known thickness in the extreme southeast part of the map area (Figure 2). The gentle eastward dip is disrupted in several areas due to faulting. The U.S. Geological Survey recovered one core and augered 97 research test holes within the Roanoke Rapids 1:100,000 map sheet to supplement sparse outcrop data available from the Coastal Plain portion of the map area. The recovered sediments were studied and data from them recorded to determine the lithologic characteristics, spatial distribution, and temporal framework of the represented Coastal Plain stratigraphic units. These test holes were critical for accurately determining the distribution of major geologic units and the position of unit boundaries that will be shown on the forthcoming Roanoke Rapids geologic map, but much of the detailed subsurface data cannot be shown readily through this map product. Therefore, detailed descriptions have been collected in this open-file report for geologists, hydrologists, engineers, and community planners to provide a detailed shallow-subsurface stratigraphic framework for much of the Roanoke Rapids map region.

Mechanical Drafting with CAD. Teacher Edition.

ERIC Educational Resources Information Center

McClain, Gerald R.

This instructor's manual contains 13 units of instruction for a course on mechanical drafting with options for using computer-aided drafting (CAD). Each unit includes some or all of the following basic components of a unit of instruction: objective sheet, suggested activities for the teacher, assignment sheets and answers to assignment sheets,…

The use of a daily goals sheet to improve communication in the paediatric intensive care unit.

PubMed

Phipps, Lorri M; Thomas, Neal J

2007-10-01

To assess the impact of the implementation of a daily goals sheet upon nursing perception of communication in an academic, tertiary care paediatric intensive care unit (PICU). Prospective, longitudinal, before-and-after intervention surveys. University affiliated 12-bed PICU. Bedside nurses. A questionnaire was administered to PICU nurses addressing their perception of communication. Following this questionnaire, the use of a daily goals sheet was instituted. A second questionnaire was administered one year later. Mann-Whitney Rank Sum Test was used to compare differences of the graded outcome variables. The primary outcome was the perception of communication taken from a nursing perspective. Eighty-five percent of nurses felt the daily goals sheet led to improved communication between physicians and nurses in the PICU. All questions related to communication demonstrated a positive influence of the goals sheet, with the perception of the PICU staff working as a team reaching statistical significance (p=0.05). The perception of the care of one surgical service being attending physician directed also significantly improved after the institution of the goals sheet (p=0.04). The institution of a daily goals sheet led to an improvement in nursing perception of communication. Future studies are required to determine if this change in process has a demonstrable effect on health care outcomes of critically ill children, or whether this tool can have the same beneficial effects in other academic and non-academic PICUs.

Heating and Air Conditioning. Auto Mechanics Curriculum Guide Module 9. Instructor's Guide.

ERIC Educational Resources Information Center

Hevel, David

This unit of instruction is one of a series of modules in the Missouri Auto Mechanics Curriculum Guide. The module's format was developed for competency-based teaching and testing. The module contains 11 units, each of which contains the following components: a competency profile, objective sheets, references, notes to the instructor, lesson…

78 FR 77649 - Polyethylene Terephthalate Film, Sheet, and Strip From the United Arab Emirates; Preliminary...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-12-24

... Film, Sheet, and Strip From the United Arab Emirates; Preliminary Results of Antidumping Duty... film, sheet, and strip (PET Film) from the United Arab Emirates (UAE). The period of review (POR) is... covered by the order are all gauges of raw, pre- treated, or primed polyethylene terephthalate film...

76 FR 22867 - Polyethylene Terephthalate Film, Sheet, and Strip From the United Arab Emirates: Final Results of...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-25

... Film, Sheet, and Strip From the United Arab Emirates: Final Results of Antidumping Duty Administrative... of administrative review of the antidumping duty order on polyethylene terephthalate film (PET Film... Polyethylene Terephthalate Film, Sheet, and Strip From the United Arab Emirates: Preliminary Results of...

76 FR 76365 - Polyethylene Terephthalate Film, Sheet, and Strip From the United Arab Emirates: Preliminary...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-07

... Film, Sheet, and Strip From the United Arab Emirates: Preliminary Results of Antidumping Duty... antidumping duty order on polyethylene terephthalate film, sheet, and strip (PET Film) from the United Arab Emirates (UAE). This review covers the respondent, JBF RAK LLC (JBF), a producer and exporter of PET Film...

75 FR 78968 - Polyethylene Terephthalate Film, Sheet, and Strip From the United Arab Emirates: Preliminary...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-12-17

... Film, Sheet, and Strip From the United Arab Emirates: Preliminary Results of Antidumping Duty... antidumping duty order on polyethylene terephthalate film, sheet, and strip (PET Film) from the United Arab...), producers and exporters of PET Film from the UAE. The Department preliminarily determines that sales of PET...

76 FR 45508 - Polyethylene Terephthalate Film, Sheet and Strip From the United Arab Emirates: Extension of Time...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-29

... DEPARTMENT OF COMMERCE International Trade Administration [A-520-803] Polyethylene Terephthalate Film, Sheet and Strip From the United Arab Emirates: Extension of Time Limit for Preliminary Results of... polyethylene terephthalate film, sheet and strip from the United Arab Emirates (UAE) for the period November 01...

Introduction to Sheet Metal. Instructor Edition. Introduction to Construction Series.

ERIC Educational Resources Information Center

Oklahoma State Dept. of Vocational and Technical Education, Stillwater. Curriculum and Instructional Materials Center.

This instructor's guide contains the materials required to teach a competency-based introductory course in sheet metal work to students who have chosen to explore careers in construction. The following topics are covered in the course's three instructional units: sheet metal materials, sheet metal tools, and applied skills. Each unit contains some…

Altitude, depth, and thickness of the Galena-Platteville Bedrock Unit in the subcrop area of Illinois and Wisconsin

USGS Publications Warehouse

Brown, Timothy A.; Dunning, Charles P.; Sharpe, Jennifer B.

2000-01-01

The report series will enable investigators involved in site-specific studies within the subcrop area to understand the regional geologic framework of the unit and to find additional reference sources. This report consists of four sheets that show the altitude (sheet 1), depth from land surface (sheet 2), total thickness (sheet 3), and location of altitude data (sheet 4) of the lithologic units that constitute the Galena-Platteville bedrock unit within the subcrop area. The sheets also show major known geologic features within the Galena-Platteville study area in Illinois and Wisconsin. A geographic information system (GIS) was used to generate data layers (coverages) from point data and from published and unpublished contour maps at various scales and detail. Standard GIS procedures were used to change the coverages into the maps shown on the sheets presented in this report. A list of references for the data used to prepare the maps is provided. 

Resistively heated shape memory polymer device

DOEpatents

Marion, III, John E.; Bearinger, Jane P.; Wilson, Thomas S.; Maitland, Duncan J.

2017-09-05

A resistively heated shape memory polymer device is made by providing a rod, sheet or substrate that includes a resistive medium. The rod, sheet or substrate is coated with a first shape memory polymer providing a coated intermediate unit. The coated intermediate unit is in turn coated with a conductive material providing a second intermediate unit. The second coated intermediate unit is in turn coated with an outer shape memory polymer. The rod, sheet or substrate is exposed and an electrical lead is attached to the rod, sheet or substrate. The conductive material is exposed and an electrical lead is attached to the conductive material.

Resistively heated shape memory polymer device

DOEpatents

Marion, III, John E.; Bearinger, Jane P.; Wilson, Thomas S.; Maitland, Duncan J.

2016-10-25

A resistively heated shape memory polymer device is made by providing a rod, sheet or substrate that includes a resistive medium. The rod, sheet or substrate is coated with a first shape memory polymer providing a coated intermediate unit. The coated intermediate unit is in turn coated with a conductive material providing a second intermediate unit. The second coated intermediate unit is in turn coated with an outer shape memory polymer. The rod, sheet or substrate is exposed and an electrical lead is attached to the rod, sheet or substrate. The conductive material is exposed and an electrical lead is attached to the conductive material.

8. SHEET 2, CONTROL HOUSE FOR DRY DOCK. United Engineering ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

8. SHEET 2, CONTROL HOUSE FOR DRY DOCK. United Engineering Company Ltd., Alameda Shipyard, Ship Repair Facilities, Office Building. John Hudspeth, Architect, at foot of Main Street, Alameda, Calif. Sheet no. 2 of 2 sheets, Plan no. 10,507. Various scales. January 4, 1943, last revised 1/19/43. U.S. Navy, Bureau of Yards & Docks, Contract no. bs 76. Approved for construction October 9, 1943. blueprint - United Engineering Company Shipyard, Control House for Dry Dock, 2900 Main Street, Alameda, Alameda County, CA

75 FR 40776 - Polyethylene Terephthalate Film, Sheet and Strip From the United Arab Emirates: Extension of Time...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-07-14

... Film, Sheet and Strip From the United Arab Emirates: Extension of Time Limit for Preliminary Results of... polyethylene terephthalate film, sheet and strip from the United Arab Emirates (UAE) for the period November 06... analysis of all information on the record, specifically considering the cost and affiliation issues in this...

Flight test and evaluation of Omega navigation in a general aviation aircraft. Volume 2: Appendices

NASA Technical Reports Server (NTRS)

Howell, J. D.; Hoffman, W. C.; Hwoschinsky, P. V.; Wischmeyer, C. E.

1975-01-01

Detailed documentation for each flight of the Omega Flight Evaluation study is presented, including flight test description sheets and actual flight data plots. Computer programs used for data processing and flight planning are explained and the data formats utilized by the Custom Interface Unit are summarized.

Active microchannel fluid processing unit and method of making

DOEpatents

Bennett, Wendy D [Kennewick, WA; Martin, Peter M [Kennewick, WA; Matson, Dean W [Kennewick, WA; Roberts, Gary L [West Richland, WA; Stewart, Donald C [Richland, WA; Tonkovich, Annalee Y [Pasco, WA; Zilka, Jennifer L [Pasco, WA; Schmitt, Stephen C [Dublin, OH; Werner, Timothy M [Columbus, OH

2001-01-01

The present invention is an active microchannel fluid processing unit and method of making, both relying on having (a) at least one inner thin sheet; (b) at least one outer thin sheet; (c) defining at least one first sub-assembly for performing at least one first unit operation by stacking a first of the at least one inner thin sheet in alternating contact with a first of the at least one outer thin sheet into a first stack and placing an end block on the at least one inner thin sheet, the at least one first sub-assembly having at least a first inlet and a first outlet; and (d) defining at least one second sub-assembly for performing at least one second unit operation either as a second flow path within the first stack or by stacking a second of the at least one inner thin sheet in alternating contact with second of the at least one outer thin sheet as a second stack, the at least one second sub-assembly having at least a second inlet and a second outlet.

Active microchannel fluid processing unit and method of making

DOEpatents

Bennett, Wendy D [Kennewick, WA; Martin, Peter M [Kennewick, WA; Matson, Dean W [Kennewick, WA; Roberts, Gary L [West Richland, WA; Stewart, Donald C [Richland, WA; Tonkovich, Annalee Y [Pasco, WA; Zilka, Jennifer L [Pasco, WA; Schmitt, Stephen C [Dublin, OH; Werner, Timothy M [Columbus, OH

2002-12-10

The present invention is an active microchannel fluid processing unit and method of making, both relying on having (a) at least one inner thin sheet; (b) at least one outer thin sheet; (c) defining at least one first sub-assembly for performing at least one first unit operation by stacking a first of the at least one inner thin sheet in alternating contact with a first of the at least one outer thin sheet into a first stack and placing an end block on the at least one inner thin sheet, the at least one first sub-assembly having at least a first inlet and a first outlet; and (d) defining at least one second sub-assembly for performing at least one second unit operation either as a second flow path within the first stack or by stacking a second of the at least one inner thin sheet in alternating contact with second of the at least one outer thin sheet as a second stack, the at least one second sub-assembly having at least a second inlet and a second outlet.

7. SHEET 1, CONTROL HOUSE FOR DRY DOCK. United Engineering ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

7. SHEET 1, CONTROL HOUSE FOR DRY DOCK. United Engineering Company Ltd., Alameda Shipyard, Ship Repair Facilities, Office Building. Plans, elevations, sections, details. John Hudspeth, Architect, at foot of Main Street, Alameda, Calif. Sheet no. 1 of 2 sheets, Plan no. 10,507. Various scales. January 4, 1943, last revised 1/28/43. U.S. Navy, Bureau of Yards & Docks, Contract no. bs 76. Approved for construction October 9, 1943. blueprint - United Engineering Company Shipyard, Control House for Dry Dock, 2900 Main Street, Alameda, Alameda County, CA

Microcomponent sheet architecture

DOEpatents

Wegeng, Robert S.; Drost, M. Kevin; McDonald, Carolyn E.

1997-01-01

The invention is a microcomponent sheet architecture wherein macroscale unit processes are performed by microscale components. The sheet architecture may be a single laminate with a plurality of separate microcomponent sections or the sheet architecture may be a plurality of laminates with one or more microcomponent sections on each laminate. Each microcomponent or plurality of like microcomponents perform at least one unit operation. A first laminate having a plurality of like first microcomponents is combined with at least a second laminate having a plurality of like second microcomponents thereby combining at least two unit operations to achieve a system operation.

Metro U.S.A. Data Sheet: Population Estimates and Selected Demographic Indicators for the Metropolitan Areas of the United States. Special edition of the United States Population Data Sheet.

ERIC Educational Resources Information Center

Population Reference Bureau, Inc., Washington, DC.

This poster-size data sheet presents population estimates and selected demographic indicators for the nation's 281 metropolitan areas. These areas are divided into 261 Metropolitan Statistical Areas (MSAs) and 20 Consolidated Metropolitan Statistical Areas (CMSAs), reporting units which replace the Standard Metropolitan Statistical Areas (SMSAs)…

Setting Goals and Getting There: Planning Tomorrow Today. BANK-ED II: Personal Money Management Series.

ERIC Educational Resources Information Center

Butterfield, Sherri M.

The three units in this guide are designed to teach language, mathematics, and social studies skills associated with earning and managing money to students in grades 7-9. Each unit includes notes to aid the teacher in preparing and presenting the material, pre/post tests, and a series of one-page reproducible sheets which contain information or…

Microcomponent chemical process sheet architecture

DOEpatents

Wegeng, Robert S.; Drost, M. Kevin; Call, Charles J.; Birmingham, Joseph G.; McDonald, Carolyn Evans; Kurath, Dean E.; Friedrich, Michele

1998-01-01

The invention is a microcomponent sheet architecture wherein macroscale unit processes are performed by microscale components. The sheet architecture may be a single laminate with a plurality of separate microcomponent sections or the sheet architecture may be a plurality of laminates with one or more microcomponent sections on each laminate. Each microcomponent or plurality of like microcomponents perform at least one chemical process unit operation. A first laminate having a plurality of like first microcomponents is combined with at least a second laminate having a plurality of like second microcomponents thereby combining at least two unit operations to achieve a system operation.

Microcomponent sheet architecture

DOEpatents

Wegeng, R.S.; Drost, M.K..; McDonald, C.E.

1997-03-18

The invention is a microcomponent sheet architecture wherein macroscale unit processes are performed by microscale components. The sheet architecture may be a single laminate with a plurality of separate microcomponent sections or the sheet architecture may be a plurality of laminates with one or more microcomponent sections on each laminate. Each microcomponent or plurality of like microcomponents perform at least one unit operation. A first laminate having a plurality of like first microcomponents is combined with at least a second laminate having a plurality of like second microcomponents thereby combining at least two unit operations to achieve a system operation. 14 figs.

Microcomponent chemical process sheet architecture

DOEpatents

Wegeng, R.S.; Drost, M.K.; Call, C.J.; Birmingham, J.G.; McDonald, C.E.; Kurath, D.E.; Friedrich, M.

1998-09-22

The invention is a microcomponent sheet architecture wherein macroscale unit processes are performed by microscale components. The sheet architecture may be a single laminate with a plurality of separate microcomponent sections or the sheet architecture may be a plurality of laminates with one or more microcomponent sections on each laminate. Each microcomponent or plurality of like microcomponents perform at least one chemical process unit operation. A first laminate having a plurality of like first microcomponents is combined with at least a second laminate having a plurality of like second microcomponents thereby combining at least two unit operations to achieve a system operation. 26 figs.

Triple-glazed insulating unit with improved edge insulation

DOEpatents

Goodwin, George B.; Buchanan, Michael J.

2016-06-07

An insulating unit includes a first spacer frame between first and second sheets, e.g. glass sheets, and a second spacer frame between the second sheet and a third sheet. A first surface of the first spacer frame is adhered to inner surface of the first sheet, and an opposite second surface of the first spacer frame is adhered to a first surface of the second sheet, by a moisture impervious adhesive layer. A first outer surface of the second spacer frame is adhered to a second surface of the second sheet, and an opposite second outer surface of the second spacer frame is adhered to an inner surface of the third sheet, by the adhesive layer. The first spacer frame and the second spacer frame have an offset of greater than zero.

General Metal Trades Book I. Units of Instruction. Teacher's Guide.

ERIC Educational Resources Information Center

East Texas State Univ., Commerce. Occupational Curriculum Lab.

This teacher's guide provides instructional materials for a 10-unit course in the General Metal Trades program. Each unit includes most or all of these basic components: performance objectives (unit and specific objectives), suggested teaching activities (a sheet outlining steps to follow to accomplish specific objectives), information sheets,…

77 FR 73010 - Polyethylene Terephthalate Film, Sheet, and Strip From the United Arab Emirates; Preliminary...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-12-07

... Film, Sheet, and Strip From the United Arab Emirates; Preliminary Results of Antidumping Duty... the antidumping duty order on polyethylene terephthalate film, sheet, and strip (PET Film) from the... covered by the order are all gauges of raw, pre- treated, or primed polyethylene terephthalate film...

Data Acquisition Unit for SATCOM Signal Analyzer

DTIC Science & Technology

1980-01-01

APSIM simulator program APDEBUG debugging program APTEST diagnostic and test program MATH Library IOP-16 16 bit I/O port 223 APPENDIX C Table...3. SYNTEST Corporation, Frequency Synthesizer Module, Data Sheet, The Syntest SM-101 Frequency Synthesizer Module, not dated . 4. DATEL Systems Inc

Instructor's Manual for Electrical Apprentice Technical Training. Series No. D (Fourth Year). Revised to Meet 1978 Electrical Code.

ERIC Educational Resources Information Center

North Carolina State Dept. of Community Colleges, Raleigh.

Twenty-seven lesson plans for a fourth-year electrical apprentice technical training program are presented in this instructor's manual. Also included are student worksheets and information sheets for each lesson, and copies of unit tests. (Answers to the worksheets and tests are provided.) The lesson plans are generally organized into four steps:…

Instructor's Manual for Electrical Apprentice Technical Training. Series No. A (First Year). Revised to Meet 1978 Electrical Code.

ERIC Educational Resources Information Center

North Carolina State Dept. of Community Colleges, Raleigh.

Thirty-six lesson plans for the first of a four-year electrical apprentice technical training program are presented in this instructor's manual. Also included are student worksheets and information sheets for each lesson, and copies of unit tests. (Answers to the worksheets and tests are provided.) The lesson plans are generally organized into…

Instructor's Manual for Electrical Apprentice Technical Training. Series No. B (Second Year). Revised to Meet 1978 Electrical Code.

ERIC Educational Resources Information Center

North Carolina State Dept. of Community Colleges, Raleigh.

Twenty-eight lesson plans for the second year of a four-year electrical apprentice technical training program are presented in this instructor's manual. Also included are student worksheets and information sheets for each lesson, and copies of unit tests. (Answers to the worksheets and tests are provided.) The lesson plans are generally organized…

Low cost solar array project production process and equipment task. A Module Experimental Process System Development Unit (MEPSDU)

NASA Technical Reports Server (NTRS)

1981-01-01

Technical readiness for the production of photovoltaic modules using single crystal silicon dendritic web sheet material is demonstrated by: (1) selection, design and implementation of solar cell and photovoltaic module process sequence in a Module Experimental Process System Development Unit; (2) demonstration runs; (3) passing of acceptance and qualification tests; and (4) achievement of a cost effective module.

Preliminary Investigation of Impact on Multiple-Sheet Structures and an Evaluation of the Meteoroid Hazard to Space Vehicles

NASA Technical Reports Server (NTRS)

Nysmith, C. Robert; Summers, James L.

1961-01-01

Small pyrex glass spheres, representative of stoney meteoroids, were fired into 2024-T3 aluminum alclad multiple-sheet structures at velocities to 11,000 feet per second to evaluate the effectiveness of multisheet hull construction as a means of increasing the resistance of a spacecraft to meteoroid penetrations. The results of these tests indicate that increasing the number of sheets in a structure while keeping the total sheet thickness constant and increasing the spacing between sheets both tend to increase the penetration resistance of a structure of constant weight per unit area. In addition, filling the space between the sheets with a light filler material was found to substantially increase structure penetration resistance with a small increase in weight. An evaluation of the meteoroid hazard to space vehicles is presented in the form of an illustrative-example for two specific lunar mission vehicles, a single-sheet, monocoque hull vehicle and a glass-wool filled, double-sheet hull vehicle. The evaluation is presented in terms of the "best" and the "worst" conditions that might be expected as determined from astronomical and satellite measurements, high-speed impact data, and hypothesized meteoroid structures and compositions. It was observed that the vehicle flight time without penetration can be increased significantly by use of multiple-sheet rather than single-sheet hull construction with no increase in hull weight. Nevertheless, it is evident that a meteoroid hazard exists, even for the vehicle with the selected multiple-sheet hull.

23. BUILDING NO. 22L, SHEET NO. 3. United Engineering Company ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

23. BUILDING NO. 22L, SHEET NO. 3. United Engineering Company Ltd., Alameda Shipyard, Ship Repair Facilities. Plans, section, & detail. Alben Froberg, Architect, 3454 Harlan Street, Oakland, California. Sheet no. 3. Plan no. 10,525. Various scales. March 1, 1943, last revised 3/15/43. U.S. Navy, Bureau of Yards & Docks, Contract no. bs 76. Approved for construction October 9, 1943. blueprint - United Engineering Company Shipyard, Engineering Building, 2900 Main Street, Alameda, Alameda County, CA

22. BUILDING NO. 22L, SHEET NO. 2. United Engineering Company ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

22. BUILDING NO. 22L, SHEET NO. 2. United Engineering Company Ltd., Alameda Shipyard, Ship Repair Facilities. Plans, section, & detail. Alben Froberg, Architect, 3454 Harlan Street, Oakland, California. Sheet no. 2. Plan no. 10,525. Various scales. March 1, 1942, last revised 3/15/43. U.S. Navy, Bureau of Yards & Docks, Contract no. bs 76. Approved for construction October 9, 1943. blueprint - United Engineering Company Shipyard, Engineering Building, 2900 Main Street, Alameda, Alameda County, CA

Hydrogeology of the Waverly-Sayre area in Tioga and Chemung ounties, New York and Bradford County, Pennsylvania

USGS Publications Warehouse

Reynolds, Richard J.

2002-01-01

The hydrogeology of a 135-square-mile area centered at Waverly, N.Y. and Sayre, Pa. is summarized in a set of five maps and a sheet of geologic sections, all at 1:24,000 scale, that depict locations of wells and test holes (sheet 1), surficial geology (sheet 2), altitude of the water table (sheet 3), saturated thickness of the surficial aquifer (sheet 4), thickness of the lacustrine confining unit (sheet 5), and geologic sections (sheet 6). The valley-fill deposits that form the aquifer system in the Waverly-Sayre area occupy an area of approximately 30 square miles, within the valleys of the Susquehanna River, Chemung River, and Cayuta Creek.The saturated thickness of the surficial aquifer, which consists of alluvium, valley-train outwash, and underlying ice-contact deposits, ranges from zero to 90 feet and is greatest in areas where (1) the outwash is underlain by ice-contact sand and gravel or (2) the outwash is overlain by alluvium and alluvial fans. Estimated transmissivity of the surficial aquifer ranges from 5,600 to 100,270 feet squared per day, and estimated hydraulic conductivity ranges from 50 feet per day for ice-contact deposits to 1,300 feet per day for well-sorted, valley-train outwash.The surficial aquifer is underlain by deposits of lacustrine sand, silt, and clay in the main valleys; these deposits reach thicknesses of as much as 150 ft and form a thick confining unit. Beneath the lacustrine silt and clay confining unit is a thin, discontinuous sand and gravel aquifer whose thickness averages 5 feet but may be as much as 30 feet locally. This confined aquifer supplies many domestic well in the area; yields average about 22 gallons per minute for 6-inch-diameter, open-ended wells. Average annual recharge to the aquifer system is estimated to be approximately 52.5 Mgal/d (million gallons per day), of which 29.7 Mgal/d is from direct precipitation, 7.6 Mgal/d is from unchanneled upland runoff that infiltrates the stratified drift along the valley wall, and 15.2 Mgal/d is from infiltration from tributary streams on the valley floor.

Hollow Fiber Spacesuit Water Membrane Evaporator Development and Testing for Advanced Spacesuits

NASA Technical Reports Server (NTRS)

Bue, Grant C.; Trevino, Luis; Tsioulos, Gus; Settles, Joseph; Colunga, Aaron; Vogel, Matthew; Vonau, Walt

2010-01-01

Grant Bue and Matthew Vogel presented the two types of Spacesuit Water Membrane Evaporators (SWME) that were developed based on hydrophobic microporous membranes. One type, the Sheet Membrane (SaM) SWME, is composed of six concentric Teflon sheet membranes fixed on cylindrical-supporting screens to form three concentric annular water channels. Those water channels are surrounded by vacuum passages to draw off the water vapor that passes through the membrane. The other type, the Hollow Fiber (HoFi) SWME, is composed of more than 14,000 tubes. Water flows through the tubes and water vapor passes through the tube wall to the shell side that vents to the vacuum of space. Both SWME types have undergone testing to baseline the performance at predicted operating temperatures and flow rates; the units also have been subjected to contamination testing and other conditions to test resiliency.

Deformation, warming and softening of Greenland’s ice by refreezing meltwater

NASA Astrophysics Data System (ADS)

Bell, Robin E.; Tinto, Kirsteen; Das, Indrani; Wolovick, Michael; Chu, Winnie; Creyts, Timothy T.; Frearson, Nicholas; Abdi, Abdulhakim; Paden, John D.

2014-07-01

Meltwater beneath the large ice sheets can influence ice flow by lubrication at the base or by softening when meltwater refreezes to form relatively warm ice. Refreezing has produced large basal ice units in East Antarctica. Bubble-free basal ice units also outcrop at the edge of the Greenland ice sheet, but the extent of refreezing and its influence on Greenland’s ice flow dynamics are unknown. Here we demonstrate that refreezing of meltwater produces distinct basal ice units throughout northern Greenland with thicknesses of up to 1,100 m. We compare airborne gravity data with modelled gravity anomalies to show that these basal units are ice. Using radar data we determine the extent of the units, which significantly disrupt the overlying ice sheet stratigraphy. The units consist of refrozen basal water commonly surrounded by heavily deformed meteoric ice derived from snowfall. We map these units along the ice sheet margins where surface melt is the largest source of water, as well as in the interior where basal melting is the only source of water. Beneath Petermann Glacier, basal units coincide with the onset of fast flow and channels in the floating ice tongue. We suggest that refreezing of meltwater and the resulting deformation of the surrounding basal ice warms the Greenland ice sheet, modifying the temperature structure of the ice column and influencing ice flow and grounding line melting.

OSL age and stratigraphy of the Strauss sand sheet in New Mexico, USA

NASA Astrophysics Data System (ADS)

Hall, Stephen A.; Goble, Ronald J.

2015-07-01

The Strauss sand sheet occurs in south-central New Mexico, USA, and northern Chihuahua, Mexico, covering an area of about 4740 km2. Its chronology is determined by 19 OSL ages. The sand sheet formed primarily during three phases of eolian deflation and deposition, each phase with a separate sand source and under different climatic and environmental circumstances. The first phase of eolian sedimentation occurred 45 to 15 ka with the deposition of unit 1. The sand source for the first phase was beach-related features along the eastern shoreline of pluvial Lake Palomas in Mexico. The glacial-age climate was cool, wet, and windy because of the southern path of the jet stream at that time. After 15 ka, with the onset of warmer conditions of the Bølling-Allerød, the shutting down of the Palomas sand source, and wet conditions of the Younger Dryas, the sand sheet stabilized with weak soil development in unit 1. By 11 ka, the climate shifted to Holocene drying conditions and the second phase of sand accumulation began, forming unit 2; the sand source was the local deflation of the previously deposited unit 1 sand. The sand sheet stabilized again by 1.9 ka with slightly wetter late Holocene climate; a weak soil formed in unit 2 sand. About A.D. 1500 and extending to about A.D. 1850 or later, an A horizon formed on the sand sheet, probably in response to a desert grassland vegetation during the period of wet climate of the Little Ice Age. In an anthropogenic third phase of eolian activity, after A.D. 1850, the vegetation was likely disturbed by overgrazing; and the unit 2 and A horizon (unit 3) sands were deflated, resulting in the deposition of a thin layer of massive eolian sand (unit 4) across the sand sheet. By about A.D. 1900 mesquite shrubs had increased in abundance; and deflated sand, largely from unit 2, began to accumulate around the shrubs, forming coppice dunes (unit 5). Mesquite coppice dunes continued to increase in number and volume during the twentieth century and at present dominate most of the sand sheet. This third phase of eolian deflation-deposition is ongoing today.

The Alcoa ram fastener: A reusable blind rivet

NASA Technical Reports Server (NTRS)

Dewalt, W. J.

1972-01-01

Results of tensile, shear, fatigue and accelerated weathering tests are presented for the ram fastener, a reusable, single unit blind rivet. The effects of variations in hole size, grip length and sheet thickness on strength properties of the fastener were determined. The test results show these fasteners to have strength characteristics suitable for light structural applications. Exposure to accelerated weathering did not impair their performance.

Animal Dissection. [Fact Sheet and Resource List Information Packet from the Humane Society of the United States].

ERIC Educational Resources Information Center

Balcombe, Jonathan

Killing animals for classroom dissection causes animal suffering, cheapens the value of life, and depletes wild animal populations, yet it remains commonplace. The Humane Society of the United States (HSUS) addresses the issue in this information packet which includes a fact sheet and three resource lists "on Dissection." The fact sheet discusses…

Sheet Membrane Spacesuit Water Membrane Evaporator Thermal Test

NASA Technical Reports Server (NTRS)

Trevino, Luis A.; Bue, Grant C.

2009-01-01

For future lunar extravehicular activities (EVA), one method under consideration for rejecting crew and electronics heat involves evaporating water through a hydrophobic, porous Teflon(Registered Trademark) membrane. A Spacesuit Water Membrane Evaporator (SWME) prototype using this membrane was successfully tested by Ungar and Thomas (2001) with predicted performance matching test data well. The above referenced work laid the foundation for the design of a compact sheet membrane SWME development unit for use in the Constellation System Spacesuit Element Portable Life Support System (Vogel and et. al., ICES 2008). Major design objectives included minimizing mass, volume, and manufacturing complexity while rejecting a minimum of 810 watts of heat from water flowing through the SWME at 91 kg/hr with an inlet temperature of 291K. The design meeting these objectives consisted of three concentric cylindrical water channels interlaced with four water vapor channels. Two units were manufactured for the purpose of investigating manufacturing techniques and performing thermal testing. The extensive thermal test measured SWME heat rejection as a function of water inlet temperatures, water flow-rates, water absolute pressures, water impurities, and water vapor back-pressures. This paper presents the test results and subsequent analysis, which includes a comparison of SWME heat rejection measurements to pretest predictions. In addition, test measurements were taken such that an analysis of the commercial-off-the-shelf vapor pressure control valve could be performed.

[Development, implementation, and analysis of a "collaborative decision-making for reasonable care" document in pediatric palliative care].

PubMed

Paoletti, M; Litnhouvongs, M-N; Tandonnet, J

2015-05-01

In France, a legal framework and guidelines state that decisions to limit treatments (DLT) require a collaborative decision meeting and a transcription of decisions in the patient's file. The do-not-attempt-resuscitation order involves the same decision-making process for children in palliative care. To fulfill the law's requirements and encourage communication within the teams, the Resource Team in Pediatric Palliative Care in Aquitaine created a document shared by all children's hospital units, tracing the decision-making process. This study analyzed the decision-making process, quality of information transmission, and most particularly the relevance of this new "collaborative decision-making for reasonable care" card. Retrospective study evaluating the implementation of a traceable document relating the DLT process. All the data sheets collected between January and December 2013 were analyzed. A total of 58 data sheets were completed between January and December 2013. We chose to collect the most relevant data to evaluate the relevance of the items to be completed and the transmission of the document, to draw up the patients' profile, and the contents of discussions with families. Of the 58 children for whom DLT was discussed, 41 data sheets were drawn up in the pediatric intensive care unit, seven in the oncology and hematology unit, five in the neonatology unit, four in the neurology unit, and one in the pneumology unit. For 30 children, one sheet was created, for 11 children, two sheets and for two children, three sheets were filled out. Thirty-nine decisions were made for withholding lifesaving treatment, 11 withdrawing treatment, and for five children, no limitation was set. Nine children survived after DLT. Of the 58 data sheets, only 31 discussions with families were related to the content of the data sheet. Of the 14 children transferred out of the unit with a completed data sheet, it was transmitted to the new unit for 11 children (79%). The number of data sheets collected in 1 year shows the value of this document. The participation of several pediatric specialities' referents in its creation, then its progressive presentation in the children's hospital units, were essential steps in introducing and establishing its use. Items describing the situation, management proposals, and adaptation of the children's supportive care were completed in the majority of cases. They correspond to a clinical description, the object of the discussion, and the daily caregiver's practices, respectively. On the other hand, discussions with families were related to the card's contents in only 53% of the cases. This can be explained by the time required to complete the DLT process. It is difficult for referring doctors to systematically, faithfully, and objectively transcribe discussions with parents. Although this process has been used for a long time in intensive care units, this document made possible an indispensable formalisation in the decision-making process. In other pediatric specialities, the sheet allowed introducing the palliative approach and was a starter and a tool for reflection on the do-not-attempt-resuscitation order, thus suggesting the need for anticipation in these situations. With the implementation of this new document, the DLT, data transmission, and continuity of care conditions were improved in the children's hospital units. Sharing this sheet with all professionals in charge of these children would support homogeneity and quality of management and care for children and their parents. Copyright © 2015 Elsevier Masson SAS. All rights reserved.

Medical-Surgical II. Teacher Edition.

ERIC Educational Resources Information Center

Oklahoma State Dept. of Vocational and Technical Education, Stillwater. Curriculum and Instructional Materials Center.

This publication is designed to provide students with the knowledge they need to pursue a career in medical-surgical nursing. Fifteen units are provided. Each instructional unit includes some or all of the basic components of a unit of instruction: performance objectives, suggested activities for the teacher, information sheets, job sheets,…

Medical-Surgical I. Teacher Edition.

ERIC Educational Resources Information Center

Oklahoma State Dept. of Vocational and Technical Education, Stillwater. Curriculum and Instructional Materials Center.

This publication is designed to provide students with the knowledge they need to pursue a career in medical-surgical nursing. Eight units are provided. Each instructional unit includes some or all of the basic components of a unit of instruction: performance objectives, suggested activities for the teacher, information sheets, job sheets, written…

Agricultural Science I. Supplementary Units. Instructor Information.

ERIC Educational Resources Information Center

Martin, Donna; And Others

These supplementary units are designed to help students with special needs learn and apply agricultural skills in the areas of animal breeding, animal nutrition, leadership, and power tools. Specific competencies are listed as study questions at the beginning of each of the 10 self-paced and self-contained units. Skill sheets, activity sheets, and…

78 FR 29700 - Polyethylene Terephthalate Film, Sheet, and Strip From the United Arab Emirates: Final Results of...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-21

... Film, Sheet, and Strip From the United Arab Emirates: Final Results of Antidumping Duty Administrative... preliminary results of administrative review of the antidumping duty order on polyethylene terephthalate film (PET Film) from the United Arab Emirates.\\1\\ This review covers two producers/exporters of subject...

Dental Charting. Learning Activities, Unit Tests, Progress Chart, and Work Sheet.

ERIC Educational Resources Information Center

Texas Univ., Austin. Center for Occupational Curriculum Development.

These materials are part of a series dealing with skills and information needed by students in dental assisting. The individualized student materials are suitable for classroom, laboratory, or cooperative training programs. These student materials, designed to be used with the Dental Charting Student Manual, consist of learning activities, unit…

Integrated Advanced Microwave Sounding Unit-A (AMSU-A. Engineering Report: Electromagnetic Interface (EMI)/Electromagnetic Radiation (EMR) and Electromagnetic Compatibility (EMC), for the METSAT/METOP AMSU-A1

NASA Technical Reports Server (NTRS)

Valdez, A.

1999-01-01

This document contains the procedure and the test results of the Advanced Microwave Sounding Unit-A (AMSU-A) Electromagnetic Interference (EMI), Electromagnetic Susceptibility, and Electromagnetic Compatibility (EMC) qualification test for the Meteorological Satellite (METSAT) and the Meteorological Operation Platform (METOP) projects. The test was conducted in accordance with the approved EMI/EMC Test Plan/Procedure, Specification number AE-26151/5D. This document describes the EMI/EMC test performed by Aerojet and it is presented in the following manner: Section-1 contains introductory material and a brief summary of the test results. Section 2 contains more detailed descriptions of the test plan, test procedure, and test results for each type of EMI/EMC test conducted. Section 3 contains supplementary information that includes test data sheets, plots, and calculations collected during the qualification testing.

40. OUTLET WORKS: VIBRATION ABSORBER FOR STANDBY UNIT, Sheet H7, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

40. OUTLET WORKS: VIBRATION ABSORBER FOR STANDBY UNIT, Sheet H-7, September, 1940. File no. SA 342/79. - Prado Dam, Outlet Works, Santa Ana River near junction of State Highways 71 & 91, Corona, Riverside County, CA

Human Trafficking of Children in the United States: A Fact Sheet

ERIC Educational Resources Information Center

US Department of Education, 2007

2007-01-01

This fact sheet presents questions and answers related to the human trafficking of children in the United States. It describes human trafficking and its extent in the United States, how human traffickers target children for coerced labor and sex exploitation, how to identify victims of human trafficking, how to report a suspected incidence of…

Method of constructing dished ion thruster grids to provide hole array spacing compensation

NASA Technical Reports Server (NTRS)

Banks, B. A. (Inventor)

1976-01-01

The center-to-center spacings of a photoresist pattern for an array of holes applied to a thin metal sheet are increased by uniformly stretching the thin metal sheet in all directions along the plane of the sheet. The uniform stretching is provided by securely clamping the periphery of the sheet and applying an annular force against the face of the sheet, within the periphery of the sheet and around the photoresist pattern. The technique is used in the construction of ion thruster grid units where the outer or downstream grid is subjected to uniform stretching prior to convex molding. The technique provides alignment of the holes of grid pairs so as to direct the ion beamlets in a direction parallel to the axis of the grid unit and thereby provide optimization of the available thrust.

The Cubans. Their History and Culture. CAL Refugee Fact Sheet Series No. 12.

ERIC Educational Resources Information Center

Robson, Barbara

This fact sheet is designed to give those working with newly arrived Cubans in the United States a brief refresher on Cuban geography and history, especially the history of Cuba's relations with the United States. It reviews events that have brought Cubans to the United States, and discusses the values newcomers are likely to have brought with…

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jozsef, G

Purpose: To build a test device for HDR afterloaders capable of checking source positions, times at positions and estimate the activity of the source. Methods: A catheter is taped on a plastic scintillation sheet. When a source travels through the catheter, the scintillator sheet lights up around the source. The sheet is monitored with a video camera, and records the movement of the light spot. The center of the spot on each image on the video provides the source location, and the time stamps of the images can provide the dwell time the source spend in each location. Finally, themore » brightness of the light spot is related to the activity of the source. A code was developed for noise removal, calibrate the scale of the image to centimeters, eliminate the distortion caused by the oblique view angle, identifying the boundaries of the light spot, transforming the image into binary and detect and calculate the source motion, positions and times. The images are much less noisy if the camera is shielded. That requires that the light spot is monitored in a mirror, rather than directly. The whole assembly is covered from external light and has a size of approximately 17×35×25cm (H×L×W) Results: A cheap camera in BW mode proved to be sufficient with a plastic scintillator sheet. The best images were resulted by a 3mm thick sheet with ZnS:Ag surface coating. The shielding of the camera decreased the noise, but could not eliminate it. A test run even in noisy condition resulted in approximately 1 mm and 1 sec difference from the planned positions and dwell times. Activity tests are in progress. Conclusion: The proposed method is feasible. It might simplify the monthly QA process of HDR Brachytherapy units.« less

Micro-Scale Mechanical Testing of Non-Woven Carbon Nanotube Sheets and Yarns

NASA Technical Reports Server (NTRS)

Magargee, J.; Morestin, F.; Cao, J.; Jones, J. S.

2013-01-01

Non-woven carbon nanotube (CNT) sheets and yarns were tested using a novel micro-scale mechanical testing system. CNT sheets were observed to delaminate during uniaxial testing using an adbesive gripping method, resulting from a higher proportion of load bearing in the outer sheets versus internal sheets and an apparently low interlaminar shear strength. In response to this, a new spool-grip method was used to alleviate non-uniform through-thickness stresses, circumvent premature delamination, and allow the sheet material to sustain a 72% increase in measured tensile strength. Furthermore, tension tests of CNT yarns showed that the yarn-structure was approximaiely 7 times stronger than the sheet structure, owing to a higher degree of CNT alignment in the test direction.

Tractor Mechanic--Student Material. Competency Based Education Curriculum.

ERIC Educational Resources Information Center

McCann, Edward W.

Developed to assist vocational agricultural mechanics students in learning to be tractor mechanics, this curriculum guide contains all the student competency sheets which comprise this competency-based curriculum. These competency sheets are categorized under sixteen instructional units. The first two units cover employment opportunities and…

Planning for an Evaluation of Teaching Performance. Volume IV. Summaries of Instruments for Use in Evaluating Teacher Performance.

ERIC Educational Resources Information Center

Yuzdepski, I., Comp.; Elliott, L., Comp.

This document presents information, in the form of summary sheets, on 54 teacher evaluation instruments. Each summary contains pertinent information about the instrument regarding publishing company, author, criteria evaluated, subject of observation, category dimension, and coding units. The 19 criteria used in the evaluation tests, which were…

Heat Rejection Systems Utilizing Composites and Heat Pipes: Design and Performance Testing

NASA Technical Reports Server (NTRS)

Jaworske, Donald A.; Beach, Duane E.; Sanzi, James L.

2007-01-01

Polymer matrix composites offer the promise of reducing the mass and increasing the performance of future heat rejection systems. With lifetimes for heat rejection systems reaching a decade or more in a micrometeoroid environment, use of multiple heat pipes for fault tolerant design is compelling. The combination of polymer matrix composites and heat pipes is of particular interest for heat rejection systems operating on the lunar surface. A technology development effort is under way to study the performance of two radiator demonstration units manufactured with different polymer matrix composite face sheet resin and bonding adhesives, along with different titanium-water heat pipe designs. Common to the two radiator demonstration units is the use of high thermal conductivity fibers in the face sheets and high thermal conductivity graphite saddles within a light weight aluminum honeycomb core. Testing of the radiator demonstration units included thermal vacuum exposure and thermal vacuum exposure with a simulated heat pipe failure. Steady state performance data were obtained at different operating temperatures to identify heat transfer and thermal resistance characteristics. Heat pipe failure was simulated by removing the input power from an individual heat pipe in order to identify the diminished performance characteristics of the entire panel after a micrometeoroid strike. Freeze-thaw performance was also of interest. This paper presents a summary of the two radiator demonstration units manufactured to support this technology development effort along with the thermal performance characteristics obtained to date. Future work will also be discussed.

75 FR 59744 - Stainless Steel Sheet and Strip From Germany, Italy, Japan, Korea, Mexico, and Taiwan

Federal Register 2010, 2011, 2012, 2013, 2014

2010-09-28

...)] Stainless Steel Sheet and Strip From Germany, Italy, Japan, Korea, Mexico, and Taiwan AGENCY: United States... duty orders on stainless steel sheet and strip from Germany, Italy, Japan, Korea, Mexico, and Taiwan... stainless steel sheet and strip from Germany, Italy, Japan, Korea, Mexico, and Taiwan would be likely to...

Filtering apparatus

DOEpatents

Haldipur, G.B.; Dilmore, W.J.

1992-09-01

A vertical vessel is described having a lower inlet and an upper outlet enclosure separated by a main horizontal tube sheet. The inlet enclosure receives the flue gas from a boiler of a power system and the outlet enclosure supplies cleaned gas to the turbines. The inlet enclosure contains a plurality of particulate-removing clusters, each having a plurality of filter units. Each filter unit includes a filter clean-gas chamber defined by a plate and a perforated auxiliary tube sheet with filter tubes suspended from each tube sheet and a tube connected to each chamber for passing cleaned gas to the outlet enclosure. The clusters are suspended from the main tube sheet with their filter units extending vertically and the filter tubes passing through the tube sheet and opening in the outlet enclosure. The flue gas is circulated about the outside surfaces of the filter tubes and the particulate is absorbed in the pores of the filter tubes. Pulses to clean the filter tubes are passed through their inner holes through tubes free of bends which are aligned with the tubes that pass the clean gas. 18 figs.

Filtering apparatus

DOEpatents

Haldipur, Gaurang B.; Dilmore, William J.

1992-01-01

A vertical vessel having a lower inlet and an upper outlet enclosure separated by a main horizontal tube sheet. The inlet enclosure receives the flue gas from a boiler of a power system and the outlet enclosure supplies cleaned gas to the turbines. The inlet enclosure contains a plurality of particulate-removing clusters, each having a plurality of filter units. Each filter unit includes a filter clean-gas chamber defined by a plate and a perforated auxiliary tube sheet with filter tubes suspended from each tube sheet and a tube connected to each chamber for passing cleaned gas to the outlet enclosure. The clusters are suspended from the main tube sheet with their filter units extending vertically and the filter tubes passing through the tube sheet and opening in the outlet enclosure. The flue gas is circulated about the outside surfaces of the filter tubes and the particulate is absorbed in the pores of the filter tubes. Pulses to clean the filter tubes are passed through their inner holes through tubes free of bends which are aligned with the tubes that pass the clean gas.

Micro-fluidic partitioning between polymeric sheets for chemical amplification and processing

DOEpatents

Anderson, Brian L.

2017-01-24

A system for fluid partitioning for chemical amplification or other chemical processing or separations of a sample, comprising a first dispenser of a first polymeric sheet, wherein the first polymeric sheet contains chambers; a second dispenser of a second polymeric sheet wherein the first dispenser and the second dispenser are positioned so that the first polymeric sheet and the second polymeric sheet become parallel; a dispenser of the fluid positioned to dispense the fluid between the first polymeric sheet and the second polymeric sheet; and a seal unit that seals the first polymeric sheet and the second polymeric sheet together thereby sealing the sample between the first polymeric sheet and the second polymeric sheet and partitioning the fluid for chemical amplification or other chemical processing or separations.

Micro-fluidic partitioning between polymeric sheets for chemical amplification and processing

DOEpatents

Anderson, Brian L.

2015-05-26

A system for fluid partitioning for chemical amplification or other chemical processing or separations of a sample, comprising a first dispenser of a first polymeric sheet, wherein the first polymeric sheet contains chambers; a second dispenser of a second polymeric sheet wherein the first dispenser and the second dispenser are positioned so that the first polymeric sheet and the second polymeric sheet become parallel; a dispenser of the fluid positioned to dispense the fluid between the first polymeric sheet and the second polymeric sheet; and a seal unit that seals the first polymeric sheet and the second polymeric sheet together thereby sealing the sample between the first polymeric sheet and the second polymeric sheet and partitioning the fluid for chemical amplification or other chemical processing or separations.

Research on Al-alloy sheet forming formability during warm/hot sheet hydroforming based on elliptical warm bulging test

NASA Astrophysics Data System (ADS)

Cai, Gaoshen; Wu, Chuanyu; Gao, Zepu; Lang, Lihui; Alexandrov, Sergei

2018-05-01

An elliptical warm/hot sheet bulging test under different temperatures and pressure rates was carried out to predict Al-alloy sheet forming limit during warm/hot sheet hydroforming. Using relevant formulas of ultimate strain to calculate and dispose experimental data, forming limit curves (FLCS) in tension-tension state of strain (TTSS) area are obtained. Combining with the basic experimental data obtained by uniaxial tensile test under the equivalent condition with bulging test, complete forming limit diagrams (FLDS) of Al-alloy are established. Using a quadratic polynomial curve fitting method, material constants of fitting function are calculated and a prediction model equation for sheet metal forming limit is established, by which the corresponding forming limit curves in TTSS area can be obtained. The bulging test and fitting results indicated that the sheet metal FLCS obtained were very accurate. Also, the model equation can be used to instruct warm/hot sheet bulging test.

Filter unit for use at high temperatures

DOEpatents

Ciliberti, David F.; Lippert, Thomas E.

1988-01-01

A filtering unit for filtering particulates from high temperature gases uses a spiral ceramic spring to bias a ceramic, tubular filter element into sealing contact with a flange about an aperture of a metallic tube sheet. The ceramic spiral spring may contact the upper edge of the filter element and be restrained by a stop member spaced from one end of the tube sheet, or the spring may contact the bottom of the filter element and be restrained by a support member spaced from the opposite end of the tube sheet. The stop member and support member are adjustably secured to the tube sheet. A filtering system uses the ceramic spiral spring to bias a plurality of ceramic, tubular filter elements in a respective plurality of apertures in a tube sheet which divides a vessel into upper and lower enclosed sections.

Qualification of an Acceptable Alternative to Halon 1211 DOD Flightline Extinguishers

DTIC Science & Technology

2008-09-01

Minimum Performance Standard MSDS Material Safety Data Sheet NATO North Atlantic Treaty Organization NAWCAD Naval Air Warfare Center Aircraft...included chronic and acute occupational exposure limits and cardiotoxicity. Alternatives that were carcinogens or that had any adverse developmental...gear to fight the fires Does not exceed pain threshold for exposed skin Each unit tested met this performance objective 2. Firefighting

Extensive massive basal-ice structures in West Antarctica relate to ice-sheet anisotropy and ice-flow

NASA Astrophysics Data System (ADS)

Ross, N.; Bingham, R. G.; Corr, H. F. J.; Siegert, M. J.

2016-12-01

Complex structures identified within both the East Antarctic and Greenland ice sheets are thought to be generated by the action of basal water freezing to the ice-sheet base, evolving under ice flow. Here, we use ice-penetrating radar to image an extensive series of similarly complex basal ice facies in West Antarctica, revealing a thick (>500 m) tectonised unit in an area of cold-based and relatively slow-flowing ice. We show that major folding and overturning of the unit perpendicular to ice flow elevates deep, warm ice into the mid ice-sheet column. Fold axes align with present ice flow, and axis amplitudes increase down-ice, suggesting long-term consistency in the direction and convergence of flow. In the absence of basal water, and the draping of the tectonised unit over major subglacial mountain ranges, the formation of the unit must be solely through the deformation of meteoric ice. Internal layer radar reflectivity is consistently greater parallel to flow compared with the perpendicular direction, revealing ice-sheet crystal anisotropy is associated with the folding. By linking layers to the Byrd ice-core site, we show the basal ice dates to at least the last glacial cycle and may be as old as the last interglacial. Deformation of deep-ice in this sector of WAIS, and potentially elsewhere in Antarctica, may be caused by differential shearing at interglacial-glacial boundaries, in a process analogous to that proposed for interior Greenland. The scale and heterogeneity of the englacial structures, and their subsequent impact on ice sheet rheology, means that the nature of ice flow across the bulk of West Antarctica must be far more complex that is currently accounted for by any numerical ice sheet model.

Hanging on to the Wetlands. Book II.

ERIC Educational Resources Information Center

Newton, David E.; Slesnick, Irwin L.

This middle/junior high school unit on wetland ecology consists of 12 activities and activity packets containing data sheets, activity sheets, flash cards, game cards, and other materials needed to complete the activities. The first activity is the text for a slide-tape show which provides an overview of the entire unit. Each of the remaining…

Hanging on to the Wetlands. Book I.

ERIC Educational Resources Information Center

Newton, David E.; Slesnick, Irwin L.

This elementary school unit on wetland ecology consists of 12 activities and activity packets containing data sheets, activity sheets, flash cards, game cards, and other materials needed to complete the activities. The first activity is the text for a slide-tape show which provides an overview of the entire unit. Each of the remaining activities…

Apollo Soyuz test project. USA-USSR, fact sheet

NASA Technical Reports Server (NTRS)

1974-01-01

The Apollo Soyuz Test Project (ASTP) is discussed. The United States and the Soviet Union have agreed to develop compatible rendezvous and docking systems which will provide a basis for docking and rescue on future spacecraft of both nations. The ASTP mission will include testing the rendezvous system in orbit, verifying techniques for transfer of astronauts and cosmonauts, and conducting experiments while docked and undocked. Diagrams of the spacecraft and systems involved in the tests are presented. The prime contractors for the equipment are identified. Biographical data on the astronauts participating in the program are provided.

Fabrication and stability investigation of ultra-thin transparent and flexible Cu-Ag-Au tri-layer film on PET

NASA Astrophysics Data System (ADS)

Prakasarao, Ch Surya; D'souza, Slavia Deeksha; Hazarika, Pratim; Karthiselva N., S.; Ramesh Babu, R.; Kovendhan, M.; Kumar, R. Arockia; Joseph, D. Paul

2018-04-01

The need for transparent conducting electrodes with high transmittance, low sheet resistance and flexibility to replace Indium Tin Oxide is ever growing. We have deposited and studied the performance of ultra-thin Cu-Ag-Au tri-layer films over a flexible poly-ethylene terephthalate substrate. Scotch tape test showed good adhesion of the metallic film. Transmittance of the tri-layer was around 40 % in visible region. Optical profiler measurements were done to study the surface features. The XRD pattern revealed that film was amorphous. Sheet resistance measured by four probe technique was around 7.7 Ohm/Δ and was stable up to 423 K. The transport parameters by Hall effect showed high conductivity and carrier concentration with a mobility of 5.58 cm2/Vs. Tests performed in an indigenously designed bending unit indicated the films to be stable both mechanically and electrically even after 50,000 bending cycles.

E-tracers: A New Technique for Wireless Sensing Under Ice Sheets

NASA Astrophysics Data System (ADS)

Burrow, S.; Wadham, J. L.; Salter, M.; Barnes, R.

2009-12-01

A significant hurdle to the understanding of ice sheet basal hydrology and its coupling with ice motion is the difficulty in making in-situ measurements along a flow path. While dye tracing techniques may be used in small glaciers to determine transit times of surface melt water through the sub-glacial system, they provide no information on in situ conditions (e.g. pressure) and are ineffective at ice-sheet scale where dilution is high. The use of tethered sensor packages is complicated by the long lengths (~100’s m) and torturous path of the moulins and conduits within ice sheets. Recent attempts to pass solid objects (rubber ducks) and other sensor packages through glacial moulins have confirmed the difficultly in deploying sensors into the sub glacial environment. Here, we report the first successful deployment and recovery of compact, electronic units to moulins up to 7 km from the margin of a large land-terminating Greenland outlet. The technique uses RF (Radio Frequency) location to create an electronic tracer (an ‘e-tracer’) enabling a data-logging sensor package to be located in the pro-glacial flood plain once it has passed through the ice sheet. A number of individual packages are used in each deployment mitigating for the risk that some may become stuck within the moulin or lodge in an inaccessible part of the floodplain. In preliminary tests on the Leverett glacier in West Greenland during August 2009 we have demonstrated that this technique can be used to locate and retrieve dummy sensor packages: 50% and 20% of the dummy sensor packages introduced to moulins at 1 and 7 km from the ice sheet terminus respectively, emerged in the sub-glacial stream. It was possible to effectively detect the e-tracer units (which broadcast on 151MHz with 10mW of power) over a horizontal range of up to 5km across the pro-glacial floodplain and locate them to a high accuracy, allowing visual recognition and manual recovery. These performance statistics give this technique strong potential for investigating in-situ conditions along a flow path at ice sheet scale.

Graphene unit cell imaging by holographic coherent diffraction.

PubMed

Longchamp, Jean-Nicolas; Latychevskaia, Tatiana; Escher, Conrad; Fink, Hans-Werner

2013-06-21

We have imaged a freestanding graphene sheet of 210 nm in diameter with 2 Å resolution by combining coherent diffraction and holography with low-energy electrons. The entire sheet is reconstructed from a single diffraction pattern displaying the arrangement of 660.000 individual graphene unit cells at once. Given the fact that electrons with kinetic energies of the order of 100 eV do not damage biological molecules, it will now be a matter of developing methods for depositing individual proteins onto such graphene sheets.

A laboratory means to produce tough aluminum sheet from powder

NASA Technical Reports Server (NTRS)

Singleton, O. R.; Royster, D. M.; Thomas, J. R.

1990-01-01

The rapid solidification of aluminum alloys as powder and the subsequent fabrication processes can be used to develop and tailor alloys to satisfy specific aerospace design requirements, including high strength and toughness. Laboratory procedures to produce aluminum powder-metallurgy (PM) materials are efficient but require evidence that the laboratory methods used can produce a product with superior properties. This paper describes laboratory equipment and procedures which can be used to produce tough aluminum PM sheet. The processing of a 2124 + 0.9 percent Zr aluminum alloy powder is used as an example. The fully hardened sheet product is evaluated in terms of properties and microstructure. The key features of the vacuum hot press pressing operation used to consolidate the powder are described. The 2124 + 0.9 percent Zr - T8 temper aluminum sheet produced was both strong (460-490 MPa yield strength) and tough (Kahn Tear unit-propagation- energy values over three times those typical for ingot metallurgy 2024-T81). Both the longitudinal and longitudinal-transverse directions of the sheet were tested. The microstructure was well refined with subgrains of one or two micrometers. Fine dispersoids of Al3Zr in the precipitate free regions adjacent to boundaries are believed to contribute to the improved toughness.

Comprehensive Small Engine Repair.

ERIC Educational Resources Information Center

Hires, Bill; And Others

This curriculum guide contains the basic information needed to repair all two- and four-stroke cycle engines. The curriculum covers four areas, each consisting of one or more units of instruction that include performance objectives, suggested activities for teacher and students, information sheets, assignment sheets, job sheets, visual aids,…

Preliminary bedrock geologic map of the Seward Peninsula, Alaska, and accompanying conodont data

USGS Publications Warehouse

Till, Alison B.; Dumoulin, Julie A.; Werdon, Melanie B.; Bleick, Heather A.

2010-01-01

This 1:500,000-scale geologic map depicts the bedrock geology of Seward Peninsula, western Alaska, on the North American side of the Bering Strait. The map encompasses all of the Teller, Nome, Solomon, and Bendeleben 1:250,000-scale quadrangles, and parts of the Shishmaref, Kotzebue, Candle, and Norton Bay 1:250,000-scale quadrangles (sheet 1; sheet 2). The geologic map is presented on Sheet 1. The pamphlet includes an introductory text, unit descriptions, tables of geochronologic data, and an appendix containing conodont (microfossil) data and a text about those data. Sheet 2 shows metamorphic and tectonic units, conodont color alteration indices, key metamorphic minerals, and locations of geochronology samples listed in the pamphlet.

Experimental formability analysis of bondal sandwich sheet

NASA Astrophysics Data System (ADS)

Kami, Abdolvahed; Banabic, Dorel

2018-05-01

Metal/polymer/metal sandwich sheets have recently attracted the interests of industries like automotive industry. These sandwich sheets have superior properties over single-layer metallic sheets including good sound and vibration damping and light weight. However, the formability of these sandwich sheets should be enhanced which requires more research. In this paper, the formability of Bondal sheet (DC06/viscoelastic polymer/DC06 sandwich sheet) was studied through different types of experiments. The mechanical properties of Bondal were determined by uniaxial tensile tests. Hemispherical punch stretching and hydraulic bulge tests were carried out to determine the forming limit diagram (FLD) of Bondal. Furthermore, cylindrical and square cup drawing tests were performed in dry and oil lubricated conditions. These tests were conducted at different blank holding forces (BHFs). An interesting observation about Bondal sheet deep drawing was obtaining of higher drawing depths at dry condition in comparison with oil-lubricated condition.

Hanging on to the Wetlands. Book III.

ERIC Educational Resources Information Center

Newton, David E.; Slesnick, Irwin L.

This high school unit on wetland ecology consists of 12 activities and activity packets containing data sheets, activity sheets, flash cards, game cards, and other materials needed to complete the activities. The first activity is the text for a slide-tape show which provides an overview of the entire unit. Each of the remaining activities is then…

Teen Sexual Activity, Pregnancy and Childbearing among Latinos in the United States. Fact Sheet.

ERIC Educational Resources Information Center

National Campaign To Prevent Teen Pregnancy, Washington, DC.

The Latino population is the fastest-growing major racial/ethnic group in the United States. By 2020, approximately 16 percent of the population will be Latino. This increase will be even more pronounced among teens. This fact sheet summarizes data from the National Vital Statistics Reports on reported sexual activity, pregnancy rates, and…

Twin-Mirrored-Galvanometer Laser-Light-Sheet Generator

NASA Technical Reports Server (NTRS)

Rhodes, David B.; Franke, John M.; Jones, Stephen B.; Leighty, Bradley D.

1991-01-01

Multiple, rotating laser-light sheets generated to illuminate flows in wind tunnels. Designed and developed to provide flexibility and adaptability to wide range of applications. Design includes capability to control size and location of laser-light sheet in real time, to generate horizontal or vertical sheets, to sweep sheet repeatedly through volume, to generate multiple sheets with controllable separation, and to rotate single or multiple laser-light sheets. Includes electronic equipment and laser mounted on adjustable-height platform. Twin-mirrored galvanometer unit supported by tripod to reduce vibration. Other possible applications include use in construction industry to align beams of building. Artistic or display applications also possible.

In situ self cross-linking of polyvinyl alcohol battery separators

NASA Technical Reports Server (NTRS)

Philipp, W. H.; Hsu, L. C.; Sheibley, D. W. (Inventor)

1979-01-01

A battery separator was produced from a polyvinyl alcohol sheet structure which was subjected to an in situ, self crosslinking process by selective oxidation of the 1,2 diol units present in the polyvinyl alcohol sheet structure. The 1,2 diol units were cleaved to form aldehyde end groups which subsequently crosslink through acetalization of the 1,3 diol units of the polyvinyl alcohol. Selective oxidation was achieved using a solution of a suitable oxidizing agent such as periodic acid or lead tetraacetate.

Comprehension of hazard communication: effects of pictograms on safety data sheets and labels.

PubMed

Boelhouwer, Eric; Davis, Jerry; Franco-Watkins, Ana; Dorris, Nathan; Lungu, Claudiu

2013-09-01

The United Nations has proposed the Globally Harmonized System (GHS) of Classification and Labelling of Chemicals to make hazard communication more uniform and to improve comprehension. Two experiments were conducted to test whether the addition of hazard and precautionary pictograms to safety data sheets and product labels would improve the transfer of information to users compared to safety data sheets and product labels containing text only. Additionally, naïve users, workers, and experts were tested to determine any potential differences among users. The effect of adding pictograms to safety data sheets and labels was statistically significant for some conditions, but was not significant across all conditions. One benefit of the addition of pictograms was that the time to respond to the survey questions decreased when the pictograms were present for both the SDS and the labels. GHS format SDS and labels do provide benefits to users, but the system will need further enhancements and modifications to continue to improve the effectiveness of hazard communication. The final rule to modify the HCS to include the Globally Harmonized System (GHS) for the Classification and Labelling of Chemicals announced by OSHA (2012b) will change the information content of every chemical SDS and label used in commerce. This study suggests that the inclusion of GHS hazard pictograms and precautionary pictograms to SDS and labels may benefit the user. Copyright © 2013 National Safety Council and Elsevier Ltd. All rights reserved.

Method and apparatus for adding electrolyte to a fuel cell stack

DOE Office of Scientific and Technical Information (OSTI.GOV)

Congdon, J.V.; English, J.G.

1986-06-24

A process is described for adding electrolyte to a fuel cell stack, the stack comprising sheet-like elements defining a plurality of fuel cell units disposed one atop the other in abutting relationship, the units defining a substantially flat, vertically extending face, each unit including a cell comprising a pair of sheet-like spaced apart gas porous electrodes with a porous matrix layer sandwiched therebetween for retaining electrolyte during cell operation, each unit also including a sheet-like substantially non-porous separator, the separator being sandwiched between the cells of adjacent units. The improvement described here consists of: extending at least one of themore » sheet-like elements of each of a plurality of the fuel cell units outwardly from the stack face to define horizontal tabs disposed one above the other; depositing dilute electrolyte directly from electrolyte supply means upon substantially the full length, parallel to the stack face, of at least the uppermost tab, the tabs being constructed and arranged such that at least a portion of the deposited electrolyte cascades from tab to tab and down the face of the stack, the deposited electrolyte being absorbed by capillary action into the elements of the stack, the step of depositing continuing until all of the electrodes and matrix layers of the stack are fully saturated with the dilute electrolyte; and thereafter evaporating liquid from the saturated elements under controlled conditions of humidity and temperature until the stack has a desired electrolyte volume and electrolyte concentration therein.« less

The Decisional Balance Sheet to Promote Healthy Behavior Among Ethnically Diverse Older Adults

PubMed Central

Geller, Karly S.; Mendoza, Ilora D.; Timbobolan, Jasah; Montjoy, Holly L.; Nigg, Claudio R.

2012-01-01

Objective The rising health care costs and increasing older adult population in the United States make preventive medicine for this age group especially crucial. Regular physical activity and fruit and vegetable consumption may prevent or delay the onset of many chronic conditions that are common among older adults. The decisional balance sheet is a promotional tool targeting the perceived pros and cons of behavior adoption. The current study tested the efficiency and effectiveness of a single-day decisional balance sheet program, targeting increased physical activity and fruit and vegetable intake among older adults. Design and Sample Participating adults (N = 21, age = 72.2) who represented a diverse population in Hawaii (Japanese = 5, Filipino = 4, Caucasian = 4, Native American = 1, Native Hawaiian = 1, Hispanic = 1, and Others = 5) were recruited from housing communities and randomized to a decisional balance sheet program adapted for physical activity or fruit and vegetable consumption. Measures Physical activity was assessed using the International Physical Activity Questionnaire (IPAQ) short form, and daily fruit and vegetable intake with the National Health and Nutrition Examination Survey single item instrument. Baseline and follow-up data were collected. Results Both programs were implemented efficiently, and participants in both groups improved their daily physical activity. The decisional balance sheet for fruit and vegetable consumption appeared less effective. Conclusions Specific suggestions for similar programs are reported. PMID:22512425

76 FR 35910 - Brass Sheet and Strip From France, Germany, Italy, and Japan; Notice of Commission Determinations...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-20

...)] Brass Sheet and Strip From France, Germany, Italy, and Japan; Notice of Commission Determinations To..., Germany, Italy, and Japan AGENCY: United States International Trade Commission. ACTION: Notice. SUMMARY... duty orders on brass sheet and strip from France, Germany, Italy, and Japan would be likely to lead to...

Database for the geologic map of upper Eocene to Holocene volcanic and related rocks in the Cascade Range, Washington

USGS Publications Warehouse

Barron, Andrew D.; Ramsey, David W.; Smith, James G.

2014-01-01

This digital database contains information used to produce the geologic map published as Sheet 1 in U.S. Geological Survey Miscellaneous Investigations Series Map I-2005. (Sheet 2 of Map I-2005 shows sources of geologic data used in the compilation and is available separately). Sheet 1 of Map I-2005 shows the distribution and relations of volcanic and related rock units in the Cascade Range of Washington at a scale of 1:500,000. This digital release is produced from stable materials originally compiled at 1:250,000 scale that were used to publish Sheet 1. The database therefore contains more detailed geologic information than is portrayed on Sheet 1. This is most noticeable in the database as expanded polygons of surficial units and the presence of additional strands of concealed faults. No stable compilation materials exist for Sheet 1 at 1:500,000 scale. The main component of this digital release is a spatial database prepared using geographic information systems (GIS) applications. This release also contains links to files to view or print the map sheet, main report text, and accompanying mapping reference sheet from Map I-2005. For more information on volcanoes in the Cascade Range in Washington, Oregon, or California, please refer to the U.S. Geological Survey Volcano Hazards Program website.

Digital case-based learning system in school.

PubMed

Gu, Peipei; Guo, Jiayang

2017-01-01

With the continuing growth of multi-media learning resources, it is important to offer methods helping learners to explore and acquire relevant learning information effectively. As services that organize multi-media learning materials together to support programming learning, the digital case-based learning system is needed. In order to create a case-oriented e-learning system, this paper concentrates on the digital case study of multi-media resources and learning processes with an integrated framework. An integration of multi-media resources, testing and learning strategies recommendation as the learning unit is proposed in the digital case-based learning framework. The learning mechanism of learning guidance, multi-media materials learning and testing feedback is supported in our project. An improved personalized genetic algorithm which incorporates preference information and usage degree into the crossover and mutation process is proposed to assemble the personalized test sheet for each learner. A learning strategies recommendation solution is proposed to recommend learning strategies for learners to help them to learn. The experiments are conducted to prove that the proposed approaches are capable of constructing personalized sheets and the effectiveness of the framework.

Digital case-based learning system in school

PubMed Central

Gu, Peipei

2017-01-01

With the continuing growth of multi-media learning resources, it is important to offer methods helping learners to explore and acquire relevant learning information effectively. As services that organize multi-media learning materials together to support programming learning, the digital case-based learning system is needed. In order to create a case-oriented e-learning system, this paper concentrates on the digital case study of multi-media resources and learning processes with an integrated framework. An integration of multi-media resources, testing and learning strategies recommendation as the learning unit is proposed in the digital case-based learning framework. The learning mechanism of learning guidance, multi-media materials learning and testing feedback is supported in our project. An improved personalized genetic algorithm which incorporates preference information and usage degree into the crossover and mutation process is proposed to assemble the personalized test sheet for each learner. A learning strategies recommendation solution is proposed to recommend learning strategies for learners to help them to learn. The experiments are conducted to prove that the proposed approaches are capable of constructing personalized sheets and the effectiveness of the framework. PMID:29107965

EXTERIOR ELEVATIONS. United Engineering Company Ltd., Alameda Shipyard, Ship Repair ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

EXTERIOR ELEVATIONS. United Engineering Company Ltd., Alameda Shipyard, Ship Repair Facilities, Office Building. Includes lettering detail for front elevation. John Hudspeth, Architect, at foot of Main Street, Alameda, Calif. Sheet no. A3 of 8 sheets, Plan no. 10,007. Scale 1/8 inch to the foot. March 18, 1942, last revised 9/21/43. U.S. Navy, Bureau of Yards & Docks, Contract no. bs 76. Approved for construction October 9, 1943. blueprint - United Engineering Company Shipyard, Office Building No. 137, 2900 Main Street, Alameda, Alameda County, CA

SECOND FLOOR AND ROOF PLANS. United Engineering Company Ltd., Alameda ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

SECOND FLOOR AND ROOF PLANS. United Engineering Company Ltd., Alameda Shipyard, Ship Repair Facilities, Office Building. Second floor plan, and roof plan. John Hudspeth, Architect, at foot of Main Street, Alameda, Calif. Sheet no. A2 of 8 sheets, Plan no. 10,007. Scale 1/8 inch to the foot. March 18, 1942, last revised 9/22/43. U.S. Navy, Bureau of Yards & Docks, Contract no. bs 76. Approved for construction October 9, 1943. blueprint - United Engineering Company Shipyard, Office Building No. 137, 2900 Main Street, Alameda, Alameda County, CA

Using Separate Answer Sheets with Grade 3 Students

ERIC Educational Resources Information Center

Brooks, Thomas; O'Malley, Kimberly; Ragland, Shelley; Young, Michael; Kirkpatrick, Rob

2014-01-01

The authors compared the performance of third-grade students testing on answer sheets with those testing on machine-scored test booklets. The 1,832 students in the nationally representative sample were assigned at the campus level to complete the Stanford Achievement Test Series, Tenth Edition in 1 of 4 conditions: (a) Form A answer sheet, (b)…

Aggregate Resources Report Department of Defense and Bureau of Land Management Lands, Southwestern United States.

DTIC Science & Technology

1978-02-10

Units ................................ 28 3.0 ARIZONA -CALIFORNIA STUDY AREA ........................ 35 3.1 Summary of Aggregate Resources...CONTENTS (Cont.) Page LIST OF APPENDICES A New Mexico-Texas Study Area Data Sheets B Arizona -California Study Area Data Sheets C Nevada-California Study...3 3 Arizona -California Study Area Location Map ..... 4 4 Nevada-California Study Area Location Map ...... 5 LIST OF TABLES 1 Preliminary

Synthesis of nanometre-thick MoO3 sheets

NASA Astrophysics Data System (ADS)

Kalantar-Zadeh, Kourosh; Tang, Jianshi; Wang, Minsheng; Wang, Kang L.; Shailos, Alexandros; Galatsis, Kosmas; Kojima, Robert; Strong, Veronica; Lech, Andrew; Wlodarski, Wojtek; Kaner, Richard B.

2010-03-01

The formation of MoO3 sheets of nanoscale thickness is described. They are made from several fundamental sheets of orthorhombic α-MoO3, which can be processed in large quantities via a low cost synthesis route that combines thermal evaporation and mechanical exfoliation. These fundamental sheets consist of double-layers of linked distorted MoO6 octahedra. Atomic force microscopy (AFM) measurements show that the minimum resolvable thickness of these sheets is 1.4 nm which is equivalent to the thickness of two double-layers within one unit cell of the α-MoO3 crystal.

Quality Control: (Material) Safety Data Sheets.

PubMed

Allen, Loyd V

2017-01-01

Safety Data Sheets (formerly Material Safety Data Sheets) are a system for cataloging information on chemicals, chemical compounds, and chemical mixtures and include instructions for the safe use and potential hazards associated with a particular material or product. At present, there are 16 sections of Safety Data Sheets, and these sections are discussed in this article. Two United States Pharmacopeia compounding-related chapters (<795> and <800>) refer to Safety Data Sheets, and this article provides a brief discussion on the terminology contained within those chapters. Copyright© by International Journal of Pharmaceutical Compounding, Inc.

Small Municipal Waste Combustion Units Air Toxics Rules Fact Sheets

EPA Pesticide Factsheets

This page contains several fact sheets with information regarding the final New Source Performance Standards (NSPS), Emission Guidelines, and Compliance Times regulations. This document provides a summary of the information for these regulations.

Synthesis of Metal Phthalocyanine Sheet Polymers

NASA Technical Reports Server (NTRS)

Achar, B. N.; Fohlen, G. M.; Parker, J. A.

1986-01-01

New method for synthesizing metal phthalocyanine tetracarboxylic acids (MPTCA's) yields high purity end product. In addition, high-purity metal phthalocyanine sheet polymers synthesized from compounds. Monomer formed into sheet polymer by heating. Units of polymer linked in manner similar to phenyl-group linkages in biphenyl: Conjugation extends throughout macromolecule, thereby increasing delocalization of TT-electrons. Increases conductivity and thermal stability of polymer.

Construction Upgrade. A Pack To Improve Communication, Numerical and IT Skills for NVQ.

ERIC Educational Resources Information Center

Rylands, Judy

This pack of materials is designed to help students working to improve their basic skills as part of their carpentry and joinery course. An introduction lists relevant core skills units and basic skills standards. The six individual sections of the pack are divided into task sheets and fact sheets. The fact sheets give information and teaching…

Damage Tolerance of Sandwich Plates with Debonded Face Sheets

NASA Technical Reports Server (NTRS)

Avery, John L., III; Sankar, Bhavani V.

1998-01-01

Axial compression tests were performed on debonded sandwich composites made of graphite/epoxy face-sheets and aramid fiber honeycomb core. The sandwich beams were manufactured using a vacuum baccrin2 process. The face-sheet and the sandwich beam were co-cured. Delamination between one of the face sheets and the core was introduced by using a Teflon layer during the curing process. Axial compression tests were performed to determine the ultimate load carrying capacity of the debonded beams. Flatwise tension tests and Double Cantilever Beam tests were performed to determine. respectively, the strength and fracture toughness of the face-sheet/core interface. From the test results semi-empirical formulas were derived for the fracture toughness and ultimate compressive load carrying capacity in terms of the core density. core thickness. face-sheet thickness and debond length. Four different failure modes and their relation to the structural properties were identified. Linear buckling analysis was found to be inadequate in predicting the compressive load carrying capacity of the debonded sandwich composites.

Fact Sheet - Final Air Toxics Rule for Gold Mine Ore Processing and Production

EPA Pesticide Factsheets

Fact sheet summarizing main points of National Emissions Standards for Hazardous Air Pollutants for gold ore processing and production facilities, the seventh largest source of mercury air emission in the United States.

Investigation of the Formability of TRIP780 Steel Sheets

NASA Astrophysics Data System (ADS)

Song, Yang

The formability of a metal sheet is dependent on its work hardening behaviour and its forming limits; and both aspects must be carefully determined in order to accurately simulate a particular forming process. This research aims to characterize the formability of a TRIP780 sheet steel using advanced experimental testing and analysis techniques. A series of flat rolling and tensile tests, as well as shear tests were conducted to determine the large deformation work hardening behaviour of this TRIP780 steel. Nakazima tests were carried out up to fracture to determine the forming limits of this sheet material. A highly-automated method for generating a robust FLC for sheet materials from DIC strain measurements was created with the help of finite element simulations, and evaluated against the conventional method. A correction algorithm that aims to compensate for the process dependent effects in the Nakazima test was implemented and tested with some success.

Fuels planning: science synthesis and integration; forest structure and fire hazard fact sheet 06: Guide to fuel treatments in dry forests of the Western United States: assessing forest structure and fire hazard

Treesearch

Rocky Mountain Research Station USDA Forest Service

2005-01-01

The Guide to Fuel Treatments analyzes a range of potential silvicultural thinnings and surface fuel treatments for 25 representative dry-forest stands in the Western United States. The guide provides quantitative guidelines and visualization for treatment based on scientific principles identified for reducing potential crown fires. This fact sheet identifies the...

EnviroAtlas - NHDPlus V2 Hydrologic Unit Boundaries Web Service - Conterminous United States

EPA Pesticide Factsheets

This EnviroAtlas web service contains layers depicting hydrologic unit boundary layers and labels for the Subregion level (4-digit HUCs), Subbasin level (8-digit HUCs), and Subwatershed level (12-digit HUCs) for the conterminous United States. EnviroAtlas (https://www.epa.gov/enviroatlas) allows the user to interact with a web-based, easy-to-use, mapping application to view and analyze multiple ecosystem services for the contiguous United States. The dataset is available as downloadable data (https://edg.epa.gov/data/Public/ORD/EnviroAtlas) or as an EnviroAtlas map service. Additional descriptive information about this dataset can be found in its associated EnviroAtlas Fact Sheet (https://www.epa.gov/enviroatlas/enviroatlas-fact-sheets).

Cancer in Children and Adolescents | Office of Cancer Genomics

Cancer.gov

View a fact sheet that has statistics as well as information about types, causes, and treatments of cancers in children and adolescents in the United States. https://www.cancer.gov/types/childhood-cancers/child-adolescent-cancers-fact-sheet

The decisional balance sheet to promote healthy behavior among ethnically diverse older adults.

PubMed

Geller, Karly S; Mendoza, Ilora D; Timbobolan, Jasah; Montjoy, Holly L; Nigg, Claudio R

2012-01-01

The rising health care costs and increasing older adult population in the United States make preventive medicine for this age group especially crucial. Regular physical activity and fruit and vegetable consumption may prevent or delay the onset of many chronic conditions that are common among older adults. The decisional balance sheet is a promotional tool targeting the perceived pros and cons of behavior adoption. The current study tested the efficiency and effectiveness of a single-day decisional balance sheet program, targeting increased physical activity and fruit and vegetable intake among older adults. Participating adults (N = 21, age = 72.2) who represented a diverse population in Hawaii (Japanese = 5, Filipino = 4, Caucasian = 4, Native American = 1, Native Hawaiian = 1, Hispanic = 1, and Others = 5) were recruited from housing communities and randomized to a decisional balance sheet program adapted for physical activity or fruit and vegetable consumption. Physical activity was assessed using the International Physical Activity Questionnaire (IPAQ) short form, and daily fruit and vegetable intake with the National Health and Nutrition Examination Survey single item instrument. Baseline and follow-up data were collected. Both programs were implemented efficiently, and participants in both groups improved their daily physical activity. The decisional balance sheet for fruit and vegetable consumption appeared less effective. Specific suggestions for similar programs are reported. © 2011 Wiley Periodicals, Inc.

Experimental analysis of the sheet metal forming behavior of newly developed press hardening steels

NASA Astrophysics Data System (ADS)

Meza-García, Enrique; Kräusel, Verena; Landgrebe, Dirk

2018-05-01

The aim of this work was the characterization of the newly developed press hardening sheet alloys 1800 PHS and 2000 PHS developed by SSAB with regard to their hot forming behavior on the basis of the experimental determination of relevant mechanical and technological properties. For this purpose conventional and non-conventional sheet metal testing methods were used. To determine the friction coefficient, the strip drawing test was applied, while the deep drawing cup test was used to determine the maximum draw depth. Finally, a V-bending test was carried out to evaluate the springback behavior of the investigated alloys by varying the blank temperature and quenching media. This work provides a technological guideline for the production of press hardened sheet parts made of these investigated sheet metals.

Double-Lap Shear Test For Honeycomb Core

NASA Technical Reports Server (NTRS)

Nettles, Alan T.; Hodge, Andrew J.

1992-01-01

Double-lap test measures shear strength of panel made of honeycomb core with 8-ply carbon-fiber/epoxy face sheets. Developed to overcome three principal disadvantages of prior standard single-lap shear test: specimen had to be more than 17 in. long; metal face sheets had to be used; and test introduced torque, with consequent bending and peeling of face sheets and spurious tensile or compressive loading of honeycomb.

Lava heating and loading of ice sheets on early Mars: Predictions for meltwater generation, groundwater recharge, and resulting landforms

NASA Astrophysics Data System (ADS)

Cassanelli, James P.; Head, James W.

2016-06-01

Recent modeling studies of the early Mars climate predict a predominantly cold climate, characterized by the formation of regional ice sheets across the highland areas of Mars. Formation of the predicted "icy highlands" ice sheets is coincident with a peak in the volcanic flux of Mars involving the emplacement of the Late Noachian - Early Hesperian ridged plains unit. We explore the relationship between the predicted early Mars "icy highlands" ice sheets, and the extensive early flood volcanism to gain insight into the surface conditions prevalent during the Late Noachian to Early Hesperian transition period. Using Hesperia Planum as a type area, we develop an ice sheet lava heating and loading model. We quantitatively assess the thermal and melting processes involved in the lava heating and loading process following the chronological sequence of lava emplacement. We test a broad range of parameters to thoroughly constrain the lava heating and loading process and outline predictions for the formation of resulting geological features. We apply the theoretical model to a study area within the Hesperia Planum region and assess the observed geology against predictions derived from the ice sheet lava heating and loading model. Due to the highly cratered nature of the Noachian highlands terrain onto which the volcanic plains were emplaced, we predict highly asymmetrical lava loading conditions. Crater interiors are predicted to accumulate greater thicknesses of lava over more rapid timescales, while in the intercrater plains, lava accumulation occurs over longer timescales and does not reach great thicknesses. We find that top-down melting due to conductive heat transfer from supraglacial lava flows is generally limited when the emplaced lava flows are less than ∼10 m thick, but is very significant at lava flow thicknesses of ∼100 m or greater. We find that bottom-up cryosphere and ice sheet melting is most likely to occur within crater interiors where lavas accumulate to a sufficient thickness to raise the ice-melting isotherm to the base of the superposed lavas. In these locations, if lava accumulation occurs rapidly, bottom-up melting of the ice sheet can continue, or begin, after lava accumulation has completed in a process we term "deferred melting". Subsurface mass loss through melting of the buried ice sheets is predicted to cause substantial subsidence in the superposed lavas, leading to the formation of associated collapse features including fracture systems, depressions, surface faulting and folding, wrinkle-ridge formation, and chaos terrain. In addition, if meltwater generated from the lava heating and loading process becomes trapped at the lava flow margins due to the presence of impermeable confining units, large highly pressurized episodic flooding events could occur. Examination of the study area reveals geological features which are generally consistent with those predicted to form as a result of the ice sheet lava heating and loading process, suggesting the presence of surface snow and ice during the Late Noachian to Early Hesperian period.

Long-term economic impact of countervailing duties on coated free sheet paper imported by the United States from China, the Republic of Korea, and Indonesia

Treesearch

Shushuai Zhu; James A. Turner; Joseph Buongiorno

2008-01-01

The international effects of United States countervailing duties on imports of coated free sheet paper from China, the Republic of Korea, and Indonesia were predicted with the Global Forest Products Model, up to the year 2020. The results indicate that the production of printing and writing paper in China, Indonesia, and the Republic of Korea would be lower. The trade...

REACH. Electricity Units. Secondary.

ERIC Educational Resources Information Center

Smith, Gene; Sappe, Hoyt

As a part of the REACH (Refrigeration, Electro-Mechanical, Air-Conditioning, Heating) electromechanical cluster, this student manual contains individualized instructional units in the area of electricity. The instructional units focus on electricity fundamentals and electric motors. Each unit follows a typical format that includes a unit sheet,…

Method of bonding

DOEpatents

Saller, deceased, Henry A.; Hodge, Edwin S.; Paprocki, Stanley J.; Dayton, Russell W.

1987-12-01

1. A method of making a fuel-containing structure for nuclear reactors, comprising providing an assembly comprising a plurality of fuel units; each fuel unit consisting of a core plate containing thermal-neutron-fissionable material, sheets of cladding metal on its bottom and top surfaces, said cladding sheets being of greater width and length than said core plates whereby recesses are formed at the ends and sides of said core plate, and end pieces and first side pieces of cladding metal of the same thickness as the core plate positioned in said recesses, the assembly further comprising a plurality of second side pieces of cladding metal engaging the cladding sheets so as to space the fuel units from one another, and a plurality of filler plates of an acid-dissolvable nonresilient material whose melting point is above 2000.degree. F., each filler plate being arranged between a pair of said second side pieces and the cladding plates of two adjacent fuel units, the filler plates having the same thickness as the second side pieces; the method further comprising enclosing the entire assembly in an envelope; evacuating the interior of the entire assembly through said envelope; applying inert gas under a pressure of about 10,000 psi to the outside of said envelope while at the same time heating the assembly to a temperature above the flow point of the cladding metal but below the melting point of any material of the assembly, whereby the envelope is pressed against the assembly and integral bonds are formed between plates, sheets, first side pieces, and end pieces and between the sheets and the second side pieces; slowly cooling the assembly to room temperature; removing the envelope; and dissolving the filler plates without attacking the cladding metal.

12. "TEST STAND; STRUCTURAL; DEFLECTOR PIT DETAILS, SHEET NO. 1." ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

12. "TEST STAND; STRUCTURAL; DEFLECTOR PIT DETAILS, SHEET NO. 1." Specifications No. ENG-04-353-55-72; Drawing No. 60-09-12; sheet 41 of 148; file no. 1320/92, Rev. A. Stamped: RECORD DRAWING - AS CONSTRUCTED. Below stamp: Contract no. 4338, no change. - Edwards Air Force Base, Air Force Rocket Propulsion Laboratory, Test Stand 1-A Terminal Room, Test Area 1-120, north end of Jupiter Boulevard, Boron, Kern County, CA

Primary Astronomy.

ERIC Educational Resources Information Center

Greenstone, Sid; Smith, Murray

Selected materials needed to teach an astronomy unit as well as suggested procedures, activities, ideas, and astronomy fact sheets published by the Manitoba Planetarium are provided. Subjects of the fact sheets include: publications and classroom picture sets available from the National Aeronautics and Space Administration and facts and statistics…

Astronomy.

ERIC Educational Resources Information Center

Greenstone, Sid; Smith, Murray

Selected materials needed to teach an astronomy unit as well as suggested procedures, activities, ideas, and astronomy fact sheets published by the Manitoba Planetarium are provided. Subjects of the fact sheets include: publications and classroom picture sets available from the National Aeronautics and Space Administration and facts and statistics…

Intermediate Astronomy.

ERIC Educational Resources Information Center

Greenstone, Sid; Smith, Murray

Selected materials needed to teach an astronomy unit as well as suggested procedures, activities, ideas, and astronomy fact sheets published by the Manitoba Planetarium are provided. Subjects of the fact sheets include: publications and classroom picture sets available from the National Aeronautics and Space Administration and facts and statistics…

Corrective Action Investigation Plan for Corrective Action Unit 563: Septic Systems, Nevada Test Site, Nevada, with Errata Sheet, Revision 0 (in English; Afrikaans)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Alfred Wickline

Corrective Action Unit 563, Septic Systems, is located in Areas 3 and 12 of the Nevada Test Site, which is 65 miles northwest of Las Vegas, Nevada. Corrective Action Unit 563 is comprised of the four corrective action sites (CASs) below: • 03-04-02, Area 3 Subdock Septic Tank • 03-59-05, Area 3 Subdock Cesspool • 12-59-01, Drilling/Welding Shop Septic Tanks • 12-60-01, Drilling/Welding Shop Outfalls These sites are being investigated because existing information on the nature and extent of potential contamination is insufficient to evaluate and recommend corrective action alternatives. Additional information will be obtained by conducting a corrective actionmore » investigation (CAI) before evaluating corrective action alternatives and selecting the appropriate corrective action for each CAS. The results of the field investigation will support a defensible evaluation of viable corrective action alternatives that will be presented in the Corrective Action Decision Document.« less

Walter Reed Army Medical Center, Washington, DC Annual Progress Report FY-89. Volume 2. Part 1

DTIC Science & Technology

1990-01-02

recurrent head and neck cancer who meet the eligibility requirements and consent to the protocol will have central venous catheter placed (if one is...DATE: 06/29/89 WORK UNIT # 6220 DETAIL SUMMARY SHEET TITLE: Epidemiology of HIV In Pediatric and Perinatal Patients - A Natural History Study...of HIV in clinical samples. 16 I I REPORT DATE: 04/04/89 WORK UNIT # 8804 DETAIL SUMMARY SHEET TITLE: The Natural History of HIV Infection and Disease

Digital Systems Validation Handbook. Volume 2

DTIC Science & Technology

1989-02-01

power. 2. A grid of wires, solid sheet, or foil. 3. A wire from circuit to grounding block or case. 4. A wire from circuit to structure. 5. Shield...RETURN. (11) 1. Structure, for power, fault, and "discrete" circuits. 2. A grid of wires, solid sheet, or foil. 3. A wire from circuit load back to...TV (14) Television TWTD (13) Thin Wire Time Domain TX (5) Transmit U.K. (13,141 United Kingdom U.S. (14) United States UART (15) Universal Asynchronous

Evolution of tholeiitic diabase sheet systems in the eastern United States: examples from the Culpeper Basin, Virginia-Maryland, and the Gettysburg Basin, Pennsylvania

USGS Publications Warehouse

Woodruff, L.G.; Froelich, A.J.; Belkin, H.E.; Gottfried, D.

1995-01-01

High-TiO2, quartz-normative (HTQ) tholeiite sheets of Early Jurassic age have intruded mainly Late Triassic sedimentary rocks in several early Mesozoic basins in the eastern US. Field observations, petrographic study, geochemical analyses and stable isotope data from three HTQ sheet systems were used to develop a general model of magmatic differentiation and magmatic-hydrothermal interaction for HTQ sheets. The three sheet systems have remarkably similar major-oxide and trace-element compositions. Cumulus and evolved diabase in comagmatic sheets separated by tens of kilometers are related by igneous differentiation. Differentiated diabase in all three sheets have petrographic and geochemical signatures and fluid inclusions indicating hydrothermal alteration beginning near magmatic temperatures and continuing to relatively low temperatures. Sulfur and oxygen isotope data are consistent with a magmatic origin for the hydrothermal fluid. -from Authors

Ice sheet altimetry

NASA Technical Reports Server (NTRS)

Brooks, R. L.

1981-01-01

Generalized surface slopes were computed for the Antarctic and Greenland ice sheets by differencing plotted contour levels and dividing them by the distance between the contours. It was observed that more than 90% of the ice sheets have surface slopes less than 1%. Seasat test mode-1 Seasat altimeter measurements over Greenland were analyzed by comparisons with collinear and intersecting normal mode Seasat altimeter passes. Over the ice sheet, the computed surface elevations from test mode-1 measurements were consistently lower by about 45 m and the AGC levels were down by approximately 6 dB. No test mode-1 data were acquired over Antarctica. It is concluded that analysis of the existing altimeter data base over the two ice sheets is crucial in designing a future improved altimeter tracking capability. It is recommended that additional waveform retracking be performed to characterize ice sheet topography as a function of geographic area and elevation.

Modelling sheet erosion on steep slopes in the loess region of China

NASA Astrophysics Data System (ADS)

Wu, Bing; Wang, Zhanli; Zhang, Qingwei; Shen, Nan; Liu, June

2017-10-01

The relationship of sheet erosion rate (SE), slope gradient (S) and rainfall intensity (I), and hydraulic parameters, such as flow velocity (V), shear stress (τ), stream power (Ω) and unit stream power (P), was investigated to derive an accurate experimental model. The experiment was conducted at slopes of 12.23%, 17.63%, 26.8%, 36.4%, 40.4% and 46.63% under I of 48, 60, 90, 120, 138 and 150 mm h-1, respectively, using simulated rainfall. Results showed that sheet erosion rate increased as a power function with rainfall intensity and slope gradient with R2 = 0.95 and Nash-Sutcliffe model efficiency (NSE) = 0.87. Sheet erosion rate was more sensitive to rainfall intensity than to slope gradient. It increased as a power function with flow velocity, which was satisfactory for predicting sheet erosion rate with R2 = 0.95 and NSE = 0.81. Shear stress and stream power could be used to predict sheet erosion rate accurately with a linear function equation. Stream power (R2 = 0.97, NSE = 0.97) was a better predictor of sheet erosion rather than shear stress (R2 = 0.90, NSE = 0.89). However, a prediction based on unit stream power was poor. The new equation (i.e. SE = 7.5 ×1012S1.43I3.04 and SE = 0.06 Ω - 0.0003 and SE = 0.011 τ - 0.01) would improve water erosion estimation on loess hillslopes of China.

Junior High Astronomy.

ERIC Educational Resources Information Center

Greenstone, Sid; Smith, Murray

Selected materials needed to teach an astronomy unit as well as suggested procedures, activities, ideas, and astronomy fact sheets published by the Manitoba Planetarium are provided. Subjects of the fact sheets include: publications and classroom picture sets available from the National Aeronautics and Space Administration and facts and statistics…

FIRST FLOOR PLAN AND SCHEDULES. United Engineering Company Ltd., Alameda ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

FIRST FLOOR PLAN AND SCHEDULES. United Engineering Company Ltd., Alameda Shipyard, Ship Repair Facilities, Office Building. First floor plan, door transom schedule, interior finish schedule, sash schedule, exterior color schedule, and location plot plan. John Hudspeth, Architect, at foot of Main Street, Alameda, Calif. Sheet no. Al of 8 sheets, Plan no. 10,007. Scale 1/8 inch to the foot. March 18, 1942, last revised 9/25/43. U.S. Navy, Bureau of Yards & Docks, Contract no. bs 76. Approved for construction October 9, 1943. blueprint - United Engineering Company Shipyard, Office Building No. 137, 2900 Main Street, Alameda, Alameda County, CA

Reshaping a multimode laser beam into a constructed Gaussian beam for generating a thin light sheet.

PubMed

Saghafi, Saiedeh; Haghi-Danaloo, Nikoo; Becker, Klaus; Sabdyusheva, Inna; Foroughipour, Massih; Hahn, Christian; Pende, Marko; Wanis, Martina; Bergmann, Michael; Stift, Judith; Hegedus, Balazs; Dome, Balazs; Dodt, Hans-Ulrich

2018-06-01

Based on the modal analysis method, we developed a model that describes the output beam of a diode-pumped solid state (DPSS) laser emitting a multimode beam. Measuring the output beam profile in the near field and at the constructed far field the individual modes, their respective contributions, and their optical parameters are determined. Using this information, the beam is optically reshaped into a quasi-Gaussian beam by the interference and superposition of the various modes. This process is controlled by a mode modulator unit that includes different meso-aspheric elements and a soft-aperture. The converted beam is guided into a second optical unit comprising achromatic-aspheric elements to produce a thin light sheet for ultramicroscopy. We found that this light sheet is markedly thinner and exhibits less side shoulders compared with a light sheet directly generated from the output of a DPSS multimode laser. © 2018 The Authors. Journal of Biophotonics published by WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Preliminary digital geologic maps of the Mariposa, Kingman, Trona, and Death Valley Sheets, California

DOE Office of Scientific and Technical Information (OSTI.GOV)

D`Agnese, F.A.; Faunt, C.C.; Turner, A.K.

1995-10-01

Parts of four 1:250,000-scale geologic maps by the California Department of Natural Resources, Division of Mines and Geology have been digitized for use in hydrogeologic characterization. These maps include the area of California between lat. 35{degree}N; Long. 115{degree}W and lat. 38{degree}N, long. 118{degree}W of the Kingman Sheet (Jennings, 1961), Trona Sheet (Jennings and others, 1962), Mariposa Sheet (Strand, 1967), and Death Valley Sheet (Streitz and Stinson, 1974). These digital maps are being released by the US Geological Survey in the ARC/INFO Version 6.1 Export format. The digitized data include geologic unit boundaries, fault traces, and identity of geologic units. Themore » procedure outlined in US Geological Survey Circular 1054 (Soller and others, 1990) was sued during the map construction. The procedure involves transferring hard-copy data into digital format by scanning manuscript maps, manipulating the digital map data, and outputting the data. Most of the work was done using Environmental Systems Research Institute`s ARC/INFO software. The digital maps are available in ARC/INFO Rev. 6.1 Export format, from the USGS, Yucca Mountain Project, in Denver, Colorado.« less

Ethanol Basics (Fact Sheet)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

2015-01-01

Ethanol is a widely-used, domestically-produced renewable fuel made from corn and other plant materials. More than 96% of gasoline sold in the United States contains ethanol. Learn more about this alternative fuel in the Ethanol Basics Fact Sheet, produced by the U.S. Department of Energy's Clean Cities program.

37 CFR 1.76 - Application data sheet.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 37 Patents, Trademarks, and Copyrights 1 2014-07-01 2014-07-01 false Application data sheet. 1.76 Section 1.76 Patents, Trademarks, and Copyrights UNITED STATES PATENT AND TRADEMARK OFFICE, DEPARTMENT OF COMMERCE GENERAL RULES OF PRACTICE IN PATENT CASES National Processing Provisions Specification § 1.76...

Massive units deposited by bedload transport in sheet flow mode

NASA Astrophysics Data System (ADS)

Viparelli, E.; Hernandez Moreira, R. R.; Jafarinik, S.; Sanders, S.; Huffman, B.; Parker, G.; Kendall, C.

2017-12-01

A sandy massive (structureless) unit overlying a basal erosional surface and underlying a parallel or cross-laminated unit often characterizes turbidity current and coastal storm deposits. The basal massive units are thought to be the result of relatively rapid deposition of suspended sediment. However, suspension-based models fail to explain how basal massive units can be emplaced for long distances, far away from the source and can contain gravel particles as floating clasts. Here we present experimental results that can significantly change the understanding of the processes forming turbidity current and coastal storm deposits. The experiments were performed in open channel flow mode in the Hydraulics Laboratory at the University of South Carolina. The sediment was a mixture of sand size particles with a geometric mean diameter of 0.95 mm and a geometric standard deviation of 1.65. Five experiments were performed with a flow rate of 30 l/s and sediment feed rates varying between 1.5 kg/min and 20 kg/min. Each experiment was characterized by two phases, 1) the equilibration phase, in which we waited for the system to reach equilibrium condition, and 2) the aggradation phase, in which we slowly raised the water surface base level to induce channel bed aggradation under the same transport conditions observed over the equilibrium bed. Our experiments show that sandy massive units can be the result of deposition from a thick bedload layer of colliding grains, the sheet flow layer. The presence of this sheet flow layer explains how a strong, sustained current can emplace extensive massive units containing gravel clasts. Although our experiments were conducted in open-channel mode, observations of bedload driven by density underflows suggest that our results are directly applicable to sheet flows driven by deep-sea turbidity currents. More specifically, we believe that this mechanism offers an explanation for massive turbidites that heretofore have been identified as the deposits of "high density" turbidity currents.

Use of raw materials in the United States from 1900 through 2014

USGS Publications Warehouse

Matos, Grecia R.

2017-08-22

The economic growth of an industrialized nation such as the United States requires raw materials for construction (buildings, bridges, highways, and so forth), defense, and processing and manufacture of goods and services. Since the beginning of the 20th century, the types and quantities of raw materials used have increased and changed significantly. This fact sheet quantifies the amounts of raw materials (other than food and fuel) that have been used in the U.S. economy annually for a period of 115 years, from 1900 through 2014. It provides a broad overview of the quantity (weight) of nonfood and nonfuel materials used in the economy and illustrates the use and significance of raw nonfuel minerals in particular as building blocks of society.These data have been compiled to help the public and policymakers understand the changing annual flow of raw materials put into use in the United States. Such information can be helpful in assessing the potential effects of materials use on the environment, assessing materials’ intensity of use, and examining the role that these materials play in the economy. The data presented indicate the substitution and shift in materials usage from renewable to nonrenewable materials during the 20th century. The disaggregated quantities by commodity (not shown in this fact sheet) may be tested against supply adequacy and end of life issues.

The Carolina Sandhills: Quaternary eolian sand sheets and dunes along the updip margin of the Atlantic Coastal Plain province, southeastern United States

USGS Publications Warehouse

Swezey, Christopher; Fitzwater, Bradley A.; Whittecar, G. Richard; Mahan, Shannon; Garrity, Christopher P.; Aleman Gonzalez, Wilma B.; Dobbs, Kerby M.

2016-01-01

The Carolina Sandhills is a physiographic region of the Atlantic Coastal Plain province in the southeastern United States. In Chesterfield County (South Carolina), the surficial sand of this region is the Pinehurst Formation, which is interpreted as eolian sand derived from the underlying Cretaceous Middendorf Formation. This sand has yielded three clusters of optically stimulated luminescence ages: (1) 75 to 37 thousand years ago (ka), coincident with growth of the Laurentide Ice Sheet; (2) 28 to 18 ka, coincident with the last glacial maximum (LGM); and (3) 12 to 6 ka, mostly coincident with the Younger Dryas through final collapse of the Laurentide Ice Sheet. Relict dune morphologies are consistent with winds from the west or northwest, coincident with modern and inferred LGM January wind directions. Sand sheets are more common than dunes because of effects of coarse grain size (mean range: 0.35–0.59 mm) and vegetation. The coarse grain size would have required LGM wind velocities of at least 4–6 m/sec, accounting for effects of colder air temperatures on eolian sand transport. The eolian interpretation of the Carolina Sandhills is consistent with other evidence for eolian activity in the southeastern United States during the last glaciation.

Math for Masons. (Revised).

ERIC Educational Resources Information Center

Heppa, Victor

This student manual is concerned with the practical application of mathematics as used by masons. The manual's design allows students to work at their own pace. Included in each of the five units are individual lesson sheets with written instructions and explanations. Each information sheet states that topic's objectives, information about the…

African American Students and U.S. High Schools. Fact Sheet

ERIC Educational Resources Information Center

Alliance for Excellent Education, 2008

2008-01-01

This fact sheet highlights the statistics of the status of the African American students living in the continental United States in terms of: population; graduation, dropouts, and preparedness; schools, segregation, and teacher quality; and special, gifted, and college preparatory education. According to the National Center for Education…

Design and fabrication of titanium multi-wall Thermal Protection System (TPS) test panels

NASA Technical Reports Server (NTRS)

Blair, W.; Meaney, J. E., Jr.; Rosenthal, H. A.

1980-01-01

A titanium multiwall thermal protection system panel was designed. The panel is a nine sheet sandwich structure consisting of an upper and lower face sheet; four dimpled sheets, three septum sheets, and clips for attachment to a vehicle structure. An acceptable fabrication process was developed, and the panel design was verified through mechanical and thermal testing of component specimens. A design was completed which takes into consideration fabrication techniques, thermal properties, mechanical properties, and materials availability.

The mechanical behavior of cross-rolled beryllium sheet

NASA Technical Reports Server (NTRS)

Henkener, J. A.; Spiker, I. K.; Castner, W. L.

1992-01-01

In response to the failure of a conical section of the Insat C satellite during certification testing, the use of beryllium for payload structures, particularly in sheet product form, is being reevaluated. A test program was initiated to study the tensile, shear, and out-of-plane failure modes of beryllium cross-rolled sheet and to apply data to the development of an appropriate failure criterion. Tensile test results indicated that sanding the surface of beryllium sheet has no significant effect on yield strength but can produce a profound reduction in ultimate strength and results obtained by finite element analysis. Critical examination of these test results may contribute to the modification of a JSC policy for the use of beryllium in orbiter and payload structures.

Performance-based readability testing of participant information for a Phase 3 IVF trial

PubMed Central

Knapp, Peter; Raynor, DK; Silcock, Jonathan; Parkinson, Brian

2009-01-01

Background Studies suggest that the process of patient consent to clinical trials is sub-optimal. Participant information sheets are important but can be technical and lengthy documents. Performance-based readability testing is an established means of assessing patient information, and this study aimed to test its application to participant information for a Phase 3 trial. Methods An independent groups design was used to study the User Testing performance of the participant information sheet from the Phase 3 'Poor Responders' trial of In Vitro Fertilisation (IVF). 20 members of the public were asked to read it, then find and demonstrate understanding of 21 key aspects of the trial. The participant information sheet was then re-written and re-designed, and tested on 20 members of the public, using the same 21 item questionnaire. Results The original participant information sheet performed well in some places. Participants could not find some answers and some of the found information was not understood. In total there were 30 instances of information being not found or not understood. Answers to three questions were found but not understood by many of the participants, these related to aspects of the drug timing, Follicle Stimulating Hormone and compensation. Only two of the 20 participants could find and show understanding of all question items when using the original sheet. The revised sheet performed generally better, with 17 instances of information being not found or not understood, although the number of 'not found' items increased. Half of the 20 participants could find and show understanding of all question items when using the revised sheet. When asked to compare the versions of the sheet, almost all participants preferred the revised version. Conclusion The original participant information sheet may not have enabled patients fully to give valid consent. Participants seeing the revised sheet were better able to understand the trial. Those who write information for trial participants should take account of good practice in information design. Performance-based User Testing may be a useful method to indicate strengths and weaknesses in trial information. PMID:19723335

Moisture Separator Reheater for NPP Turbines

NASA Astrophysics Data System (ADS)

Manabe, Jun; Kasahara, Jiro

This paper introduces the development of the current model Moisture Separator Reheater (MSR) for nuclear power plant (NPP) turbines, commercially placed in service in the period 1984-1997, focusing on the mist separation performance of the MSR along with drainage from heat exchanger tubes. A method of predicting the mist separation performance was devised first based on the observation of mist separation behaviors under an air-water test. Then the method was developed for the application to predict under the steam conditions, followed by the verification in comparison with the actual results of a steam condition test. The instability of tube drainage associated with both sub-cooling and temperature oscillation might adversely affect the seal welding of tubes to tube sheet due to thermal fatigue. The instability was measured on an existing unit to clarify behaviors and the development of a method to suppress them. Both methods were applied to newly constructed units and the effectiveness of the methods was demonstrated.

Stratigraphy and sedimentology of a dry to wet eolian depositional system, Burns formation, Meridiani Planum, Mars

NASA Astrophysics Data System (ADS)

Grotzinger, J. P.; Arvidson, R. E.; Bell, J. F.; Calvin, W.; Clark, B. C.; Fike, D. A.; Golombek, M.; Greeley, R.; Haldemann, A.; Herkenhoff, K. E.; Jolliff, B. L.; Knoll, A. H.; Malin, M.; McLennan, S. M.; Parker, T.; Soderblom, L.; Sohl-Dickstein, J. N.; Squyres, S. W.; Tosca, N. J.; Watters, W. A.

2005-11-01

Outcrop exposures of sedimentary rocks at the Opportunity landing site (Meridiani Planum) form a set of genetically related strata defined here informally as the Burns formation. This formation can be subdivided into lower, middle, and upper units which, respectively, represent eolian dune, eolian sand sheet, and mixed eolian sand sheet and interdune facies associations. Collectively, these three units are at least 7 m thick and define a "wetting-upward" succession which records a progressive increase in the influence of groundwater and, ultimately, surface water in controlling primary depositional processes. The Burns lower unit is interpreted as a dry dune field (though grain composition indicates an evaporitic source), whose preserved record of large-scale cross-bedded sandstones indicates either superimposed bedforms of variable size or reactivation of lee-side slip faces by episodic (possibly seasonal) changes in wind direction. The boundary between the lower and middle units is a significant eolian deflation surface. This surface is interpreted to record eolian erosion down to the capillary fringe of the water table, where increased resistance to wind-induced erosion was promoted by increased sediment cohesiveness in the capillary fringe. The overlying Burns middle unit is characterized by fine-scale planar-laminated to low-angle-stratified sandstones. These sandstones accumulated during lateral migration of eolian impact ripples over the flat to gently undulating sand sheet surface. In terrestrial settings, sand sheets may form an intermediate environment between dune fields and interdune or playa surfaces. The contact between the middle and upper units of the Burns formation is interpreted as a diagenetic front, where recrystallization in the phreatic or capillary zones may have occurred. The upper unit of the Burns formation contains a mixture of sand sheet facies and interdune facies. Interdune facies include wavy bedding, irregular lamination with convolute bedding and possible small tepee or salt-ridge structures, and cm-scale festoon cross-lamination indicative of shallow subaqueous flows marked by current velocities of a few tens of cm/s. Most likely, these currents were gravity-driven, possibly unchannelized flows resulting from the flooding of interdune/playa surfaces. However, evidence for lacustrine sedimentation, including mudstones or in situ bottom-growth evaporites, has not been observed so far at Eagle and Endurance craters. Mineralogical and elemental data indicate that the eolian sandstones of the lower and middle units, as well as the subaqueous and eolian deposits of the Burns upper unit, were derived from an evaporitic source. This indirectly points to a temporally equivalent playa where lacustrine evaporites or ground-water-generated efflorescent crusts were deflated to provide a source of sand-sized particles that were entrained to form eolian dunes and sand sheets. This process is responsible for the development of sulfate eolianites at White Sands, New Mexico, and could have provided a prolific flux of sulfate sediment at Meridiani. Though evidence for surface water in the Burns formation is mostly limited to the upper unit, the associated sulfate eolianites provide strong evidence for the critical role of groundwater in controlling sediment production and stratigraphic architecture throughout the formation.

Crib sheets or security blankets?

PubMed

Drake, V K; Freed, P; Hunter, J M

1998-01-01

This article describes the sanctioned use of crib sheets as a nursing intervention to decrease test anxiety when the classroom is the practice setting for psychiatric/mental health nursing faculty. The products that the students created offered additional unsuspected benefits. The faculty were convinced that the use of crib sheets can be a sound intervention to reduce students' test-taking anxiety.

16 CFR 1632.3 - General requirements.

Code of Federal Regulations, 2011 CFR

2011-01-01

...) Summary of test method. The method measures the ignition resistance of a mattress or mattress pad by... surface. A two-sheet test is also conducted on similar surface locations. In the latter test, the burning cigarettes are placed between the sheets. (b) Test criterion. When testing the mattress or mattress pad...

16 CFR 1632.3 - General requirements.

Code of Federal Regulations, 2010 CFR

2010-01-01

...) Summary of test method. The method measures the ignition resistance of a mattress or mattress pad by... surface. A two-sheet test is also conducted on similar surface locations. In the latter test, the burning cigarettes are placed between the sheets. (b) Test criterion. When testing the mattress or mattress pad...

16 CFR 1632.3 - General requirements.

Code of Federal Regulations, 2014 CFR

2014-01-01

...) Summary of test method. The method measures the ignition resistance of a mattress or mattress pad by... surface. A two-sheet test is also conducted on similar surface locations. In the latter test, the burning cigarettes are placed between the sheets. (b) Test criterion. When testing the mattress or mattress pad...

16 CFR 1632.3 - General requirements.

Code of Federal Regulations, 2012 CFR

2012-01-01

...) Summary of test method. The method measures the ignition resistance of a mattress or mattress pad by... surface. A two-sheet test is also conducted on similar surface locations. In the latter test, the burning cigarettes are placed between the sheets. (b) Test criterion. When testing the mattress or mattress pad...

Production development of organic nonflammable spacecraft potting, encapsulating and conformal coating compounds. Volume 3: Appendices

NASA Technical Reports Server (NTRS)

Lieberman, S. L.

1974-01-01

Appendices are presented which include: statement of work; material vendor contacts; formulation/processing data sheet; upward propagation test; flammability test conditions/results sheet; odor test; vacuum stability requirements; flammability test facility; determination of offgassing products and carbon monoxide test; and pneumatic and mechanical impact test guidelines.

49 CFR 180.215 - Reporting and record retention requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

..., as well as unsuccessful tests. The entry for a second test after a failure to hold test pressure must..., pressure test, and ultrasonic examination if permitted under a special permit, as applicable, must be... each test sheet, provided each test on the sheet was conducted on that date. Ditto marks or a solid...

Skiving stacked sheets of paper into test paper for rapid and multiplexed assay

PubMed Central

Yang, Mingzhu; Zhang, Wei; Yang, Junchuan; Hu, Binfeng; Cao, Fengjing; Zheng, Wenshu; Chen, Yiping; Jiang, Xingyu

2017-01-01

This paper shows that stacked sheets of paper preincubated with different biological reagents and skiving them into uniform test paper sheets allow mass manufacturing of multiplexed immunoassay devices and simultaneous detection of multiplex targets that can be read out by a barcode scanner. The thickness of one sheet of paper can form the width of a module for the barcode; when stacked, these sheets of paper can form a series of barcodes representing the targets, depending on the color contrast provided by a colored precipitate of an immunoassay. The uniform thickness of sheets of paper allows high-quality signal readout. The manufacturing method allows highly efficient fabrication of the materials and substrates for a straightforward assay of targets that range from drugs of abuse to biomarkers of blood-transmitted infections. In addition, as a novel alternative to the conventional point-of-care testing method, the paper-based barcode assay system can provide highly efficient, accurate, and objective diagnoses. PMID:29214218

The effect of mesenchymal stem cell sheets on structural allograft healing of critical-sized femoral defects in mice

PubMed Central

Long, Teng; Zhu, Zhenan; Awad, Hani A.; Schwarz, Edward M.; Hilton, Matthew J.; Dong, Yufeng

2014-01-01

Structural bone allografts are widely used in the clinic to treat critical sized bone defects, despite lacking the osteoinductive characteristics of live autografts. To address this, we generated revitalized structural allografts wrapped with mesenchymal stem/progenitor cell (MSC) sheets, which were produced by expanding primary syngenic bone marrow derived cells on temperature-responsive plates, as a tissue engineered periosteum. In vitro assays demonstrated maintenance of the MSC phenotype in the sheets, suggesting that short-term culturing of MSC sheets is not detrimental. To test their efficacy in vivo, allografts wrapped with MSC sheets were transplanted into 4-mm murine femoral defects and compared to allografts with direct seeding of MSCs and allografts without cells. Evaluations consisted of x-ray plain radiography, 3D microCT, histology, and biomechanical testing at 4- and 6-weeks post-surgery. Our findings demonstrate that MSC sheets induce prolonged cartilage formation at the graft-host junction and enhanced bone callus formation, as well as graft-host osteointegration. Moreover, a large periosteal callus was observed spanning the allografts with MSC sheets, which partially mimics live autograft healing. Finally, biomechanical testing showed a significant increase in the structural and functional properties of MSC sheet grafted femurs. Taken together, MSC sheets exhibit enhanced osteogenicity during critical sized bone defect repair, demonstrating the feasibility of this tissue engineering solution for massive allograft healing. PMID:24393269

Utilization of a Biodegradable Mulch Sheet Produced from Poly(Lactic Acid)/Ecoflex®/Modified Starch in Mandarin Orange Groves

PubMed Central

Tachibana, Yuya; Maeda, Takuya; Ito, Osamu; Maeda, Yasukatsu; Kunioka, Masao

2009-01-01

We have developed a mulch sheet made by inflation molding of PLA, Ecoflex® and modified starch, which all have different biodegradabilities. A field test of use as an agricultural mulch sheet for mandarin oranges was carried out over two years. The mechanical properties of the mulch sheet were weakened with time during the field test, but the quality of the mandarin oranges increased, a result of the controlled degradation of the sheet. The most degradable modified starch degraded first, allowing control of the moisture on the soil. Accelerator mass spectroscopy was used for evaluation of the biomass carbon ratio. The biomass carbon ratio decreased by degradation of the biobased materials, PLA and modified starch in the mulch sheet. PMID:19812715

Limited Impact of Subglacial Supercooling Freeze-on for Greenland Ice Sheet Stratigraphy

NASA Astrophysics Data System (ADS)

Dow, Christine F.; Karlsson, Nanna B.; Werder, Mauro A.

2018-02-01

Large units of disrupted radiostratigraphy (UDR) are visible in many radio-echo sounding data sets from the Greenland Ice Sheet. This study investigates whether supercooling freeze-on rates at the bed can cause the observed UDR. We use a subglacial hydrology model to calculate both freezing and melting rates at the base of the ice sheet in a distributed sheet and within basal channels. We find that while supercooling freeze-on is a phenomenon that occurs in many areas of the ice sheet, there is no discernible correlation with the occurrence of UDR. The supercooling freeze-on rates are so low that it would require tens of thousands of years with minimal downstream ice motion to form the hundreds of meters of disrupted radiostratigraphy. Overall, the melt rates at the base of the ice sheet greatly overwhelm the freeze-on rates, which has implications for mass balance calculations of Greenland ice.

Map and tabulation of quaternary mass movements along the United States-Canadian Atlantic continental slope from 32 degrees 00 minutes to 47 degrees 00 minutes N. latitude

USGS Publications Warehouse

Booth, J.S.; O'Leary, Dennis W.; Popenoe, Peter; Robb, James M.; McGregor, B.A.

1988-01-01

Since the initial report on the Grand Banks Slump off southern Newfoundland (Heezen and Ewing, 1952), a large body of data on submarine mass movement along the Atlantic continental margin of the United States and Canada has been published.  These data were compiled to provide this distribution map (sheet 1) and tabulation (sheet 2) of "principal facts" on mass movement of the northwest Atlantic Continental Slope.  Although we prepared this inventory to facilitate our study of Quaternary mass movement along the U.S. Continental Slope, we judged the compilation to be large enough and detailed enough to be published as a generally useful data source and compendium.  Sheet 3 shows examples of mass movement styles.

Do You Prefer to Have the Text or a Sheet with Your Physics Exams?

NASA Astrophysics Data System (ADS)

Hamed, Kastro M.

2008-05-01

Many high school and introductory college physics instructors ponder the choice between "open text" exams versus "facts and formulae sheet" exams. Other alternatives are closed book/closed notes exams or an instructor-prepared sheet of facts and relevant formulas. There is no agreement on merit. Rehfuss strongly opposes allowing students to use formula sheets while taking physics exams despite acknowledging that such use is common practice. Cone2 responded to Rehfuss by defending the use of such sheets and outlining the benefits of a "cheat sheet." Debate over the use of a "cheat sheet" or other resources during exams is not limited to the physics community. Skidmore and Aagaard3 studied the relationship between testing conditions and student test scores for students in teacher education. Two decades earlier Boniface,4 Dorsal and Cundiff,5 and Hindman6 published papers on the use of texts and/or sheets during examinations in psychology and education. Others, such as Pullen et al.7 focused on studying the discarded cheat sheets themselves. Humorously, in October 2005 The New York Times8 reported an unusual museum exhibit of "cheat sheets" and the different ways students had cheated at a particular university.

Benchmark Testing of the Largest Titanium Aluminide Sheet Subelement Conducted

NASA Technical Reports Server (NTRS)

Bartolotta, Paul A.; Krause, David L.

2000-01-01

To evaluate wrought titanium aluminide (gamma TiAl) as a viable candidate material for the High-Speed Civil Transport (HSCT) exhaust nozzle, an international team led by the NASA Glenn Research Center at Lewis Field successfully fabricated and tested the largest gamma TiAl sheet structure ever manufactured. The gamma TiAl sheet structure, a 56-percent subscale divergent flap subelement, was fabricated for benchmark testing in three-point bending. Overall, the subelement was 84-cm (33-in.) long by 13-cm (5-in.) wide by 8-cm (3-in.) deep. Incorporated into the subelement were features that might be used in the fabrication of a full-scale divergent flap. These features include the use of: (1) gamma TiAl shear clips to join together sections of corrugations, (2) multiple gamma TiAl face sheets, (3) double hot-formed gamma TiAl corrugations, and (4) brazed joints. The structural integrity of the gamma TiAl sheet subelement was evaluated by conducting a room-temperature three-point static bend test.

Magnetohydrodynamics with GAMER

NASA Astrophysics Data System (ADS)

Zhang, Ui-Han; Schive, Hsi-Yu; Chiueh, Tzihong

2018-06-01

GAMER, a parallel Graphic-processing-unit-accelerated Adaptive-MEsh-Refinement (AMR) hydrodynamic code, has been extended to support magnetohydrodynamics (MHD) with both the corner-transport-upwind and MUSCL-Hancock schemes and the constraint transport technique. The divergent preserving operator for AMR has been applied to reinforce the divergence-free constraint on the magnetic field. GAMER-MHD has fully exploited the concurrent executions between the graphic process unit (GPU) MHD solver and other central processing unit computation pertinent to AMR. We perform various standard tests to demonstrate that GAMER-MHD is both second-order accurate and robust, producing results as accurate as those given by high-resolution uniform-grid runs. We also explore a new 3D MHD test, where the magnetic field assumes the Arnold–Beltrami–Childress configuration, temporarily becomes turbulent with current sheets, and finally settles to a lowest-energy equilibrium state. This 3D problem is adopted for the performance test of GAMER-MHD. The single-GPU performance reaches 1.2 × 108 and 5.5 × 107 cell updates per second for the single- and double-precision calculations, respectively, on Tesla P100. We also demonstrate a parallel efficiency of ∼70% for both weak and strong scaling using 1024 XK nodes on the Blue Waters supercomputers.

16 CFR § 1632.3 - General requirements.

Code of Federal Regulations, 2013 CFR

2013-01-01

... General requirements. (a) Summary of test method. The method measures the ignition resistance of a... the mattress or mattress pad surface. A two-sheet test is also conducted on similar surface locations. In the latter test, the burning cigarettes are placed between the sheets. (b) Test criterion. When...

Multi-Objective Parallel Test-Sheet Composition Using Enhanced Particle Swarm Optimization

ERIC Educational Resources Information Center

Ho, Tsu-Feng; Yin, Peng-Yeng; Hwang, Gwo-Jen; Shyu, Shyong Jian; Yean, Ya-Nan

2009-01-01

For large-scale tests, such as certification tests or entrance examinations, the composed test sheets must meet multiple assessment criteria. Furthermore, to fairly compare the knowledge levels of the persons who receive tests at different times owing to the insufficiency of available examination halls or the occurrence of certain unexpected…

Woven heat exchanger

DOEpatents

Piscitella, Roger R.

1987-01-01

In a woven ceramic heat exchanger using the basic tube-in-shell design, each heat exchanger consisting of tube sheets and tube, is woven separately. Individual heat exchangers are assembled in cross-flow configuration. Each heat exchanger is woven from high temperature ceramic fiber, the warp is continuous from tube to tube sheet providing a smooth transition and unitized construction.

Energy. Overview: ERIC Fact Sheet No. 6.

ERIC Educational Resources Information Center

Arrington, Larry

This fact sheet provides a basic overview of energy problems and programs in the United States and discusses the role that vocational education can play in solving those problems. The National Energy Plan is described including its objectives, strategies, and seven legislative acts: (1) The National Energy Conservation Act; (2) The Power Plant and…

Other Solid Waste Incineration (OSWI) Units Standards of Performance for New Stationary Sources and Emission Guidelines for Existing Sources Fact Sheets

EPA Pesticide Factsheets

This page contains a November 2005, and and November 2006 fact sheet with information regarding the final and proposed NSPS and Emission Guidelines for Existing Sources for OSWI. This document provides a summary of the information for this regulation

75 FR 61772 - Certain Coated Paper Suitable for High-Quality Print Graphics Using Sheet-Fed Presses From China...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-10-06

... INTERNATIONAL TRADE COMMISSION [Investigation Nos. 701-TA-470-471 and 731-TA-1169-1170 (Final)] Certain Coated Paper Suitable for High-Quality Print Graphics Using Sheet-Fed Presses From China and Indonesia AGENCY: United States International Trade Commission. ACTION: Revised schedule for the subject...

75 FR 54650 - Certain Coated Paper Suitable for High-Quality Print Graphics Using Sheet-Fed Presses From China...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-09-08

... INTERNATIONAL TRADE COMMISSION [Investigation Nos. 701-TA-470-471 and 731-TA-1169-1170 (Final)] Certain Coated Paper Suitable for High-Quality Print Graphics Using Sheet-Fed Presses From China and Indonesia AGENCY: United States International Trade Commission. ACTION: Revised schedule for the subject...

Woven heat exchanger

DOEpatents

Piscitella, Roger R.

1987-05-05

In a woven ceramic heat exchanger using the basic tube-in-shell design, each heat exchanger consisting of tube sheets and tube, is woven separately. Individual heat exchangers are assembled in cross-flow configuration. Each heat exchanger is woven from high temperature ceramic fiber, the warp is continuous from tube to tube sheet providing a smooth transition and unitized construction.

Characteristics of a young lava-hyaloclastite sheet, Snaebylisheidi, Iceland

NASA Astrophysics Data System (ADS)

White, J. D.; Gorny, C. F.; Gudmundsson, M. T.

2009-12-01

Extensive sheets of hyaloclastite volcaniclastic debris, coupled with and intruded by largely underlying layers of coherent basalt, are common in the Sida area of southeastern Iceland. They were initially interpreted as submarine deposits, but have recently been re-interpreted as nonmarine deposits formed in the presence of glaciers. Detailed interpretation of the units has been challenging, because their source areas are not preserved. A younger deposit of the same type forms an elongate flat-topped ridge in the Snaebylisheidi area. Its volume of ca. 35 cubic km is similar to that of the larger Sida units, its source area is preserved, and parts of the deposit remain unlithified. Our initial investigation reveals that the source area is dominated by clastic deposits. There is no evidence for a source edifice of pillow or sheet lavas, but there are extensive low-level intrusions near the base, and a plexus of smaller high-level intrusions showing evidence of high viscosities during emplacement. Isolated pillows and other fluidal juvenile clasts near the source lie within matrices of highly vesicular ash and lapilli, or of mixed vesicular and dense glassy fragments. Downstream in the unit, deposits are dominated by dense clasts, and these can in places be demonstrated to have been derived locally from the underlying to intruding basalt sheet. Larger dense clasts are commonly highly irregular, vuggy, and composite; in places many are rolled into subspherical forms enclosing matrix material comprising dense angular glass fragments. The clastic part of the unit has an upper subunit dominated by well-developed bedding in complex geometries with multiple internal truncation surfaces. Lower subunits include thick structureless to alignment-bedded layers, along with intrusion-dominated zones. Soft-sediment deformation is ubiquitous along the edges of the deposit, with many layers broken and tilted to subvertical inclinations. Taken together, these features indicate that little or no lava accumulated at the source area during eruption, but that much basalt was intruded into unconsolidated volcaniclastic deposits. Coherent basalt sheets extended downslope from the source, perhaps largely as intrusions into earlier-deposited tephra, and produced much of the downstream clastic material by local fragmentation of the advancing sheet. Thick beds reflecting high accumulation rates are intercalated with groups of thinner beds formed by multiple depositional pulses. Deformation along deposit tops and edges records pervasive slumping of the unconsolidated deposits. The characteristics overall are suggestive of an initially explosive subglacial origin, with much of the unit emplaced subglacially. More work is underway to better understand the source eruption, and the way in which the basalt sheet was emplaced and associated volcaniclastic deposits produced and deposited.

NDE evidence for the damage arrestment performance of PRSEUS composite cube during high-pressure load test

NASA Astrophysics Data System (ADS)

Johnston, Patrick H.; Parker, F. Raymond

2014-02-01

As an approach to light-weight, cost-effective and manufacturable structures required to enable the hybrid wing body aircraft, The Boeing Company, Inc. and NASA have developed the Pultruded Rod Stitched Efficient Unitized Structure (PRSEUS) concept. A PRSEUS pressure cube was developed as a risk reduction test article to examine a new integral cap joint concept as part of a building block approach for technology development of the PRSEUS concept. The overall specimen strength exceeded the 18.4 psi load requirement as testing resulted in the cube reaching a final pressure load of around 48 psi prior to catastrophic failure. The cube pressure test verified that the joints and structure were capable of sustaining the required loads, and represented the first testing of joined PRSEUS structure. This paper will address the damage arrestment performance of the stitched PRSEUS structure. Following catastrophic failure of the cube, ultrasonic pulse-echo inspection found that the localized damage, surrounding a barely-visible impact damage site, did not change noticeably between just after impact and catastrophic failure of the cube, and did not play a role in the catastrophic failure event. Ultrasonic inspection of the remaining intact cube panels presented three basic types of indications: delaminations between laminae parallel to the face sheets, lying between face sheet and tear strap layers, or between tear strap and flange layers; delaminations above the noodles of stringers, frames or integral caps, lying within face sheet or tear strap layers; and delaminations between the laminae in the inner fillets of the integral caps, where pulloff stresses were expected to be highest. Delaminations of all three types were predominantly contained by the first row of stitches encountered. For the small fraction of delaminations extending beyond the first row of stitches, all were contained by the second stitch row.

NDE Evidence for the Damage Arrestment Performance of PRSEUS Composite Cube During High-Pressure Load Test

NASA Technical Reports Server (NTRS)

Johnston, Patrick H.; Parker, F. Raymond

2013-01-01

As an approach to light-weight, cost-effective and manufacturable structures required to enable the hybrid wing body aircraft, The Boeing Company, Inc. and NASA have developed the Pultruded Rod Stitched Efficient Unitized Structure (PRSEUS) concept. A PRSEUS pressure cube was developed as a risk reduction test article to examine a new integral cap joint concept as part of a building block approach for technology development of the PRSEUS concept. The overall specimen strength exceeded the 18.4 psi load requirement as testing resulted in the cube reaching a final pressure load of around 48 psi prior to catastrophic failure. The cube pressure test verified that the joints and structure were capable of sustaining the required loads, and represented the first testing of joined PRSEUS structure. This paper will address the damage arrestment performance of the stitched PRSEUS structure. Following catastrophic failure of the cube, ultrasonic pulse-echo inspection found that the localized damage, surrounding a barely-visible impact damage site, did not change noticeably between just after impact and catastrophic failure of the cube, and did not play a role in the catastrophic failure event. Ultrasonic inspection of the remaining intact cube panels presented three basic types of indications: delaminations between laminae parallel to the face sheets, lying between face sheet and tear strap layers, or between tear strap and flange layers; delaminations above the noodles of stringers, frames or integral caps, lying within face sheet or tear strap layers; and delaminations between the laminae in the inner fillets of the integral caps, where pulloff stresses were expected to be highest. Delaminations of all three types were predominantly contained by the first row of stitches encountered. For the small fraction of delaminations extending beyond the first row of stitches, all were contained by the second stitch row.

Sensing sheets based on large area electronics for fatigue crack detection

NASA Astrophysics Data System (ADS)

Yao, Yao; Glisic, Branko

2015-03-01

Reliable early-stage damage detection requires continuous structural health monitoring (SHM) over large areas of structure, and with high spatial resolution of sensors. This paper presents the development stage of prototype strain sensing sheets based on Large Area Electronics (LAE), in which thin-film strain gauges and control circuits are integrated on the flexible electronics and deposited on a polyimide sheet that can cover large areas. These sensing sheets were applied for fatigue crack detection on small-scale steel plates. Two types of sensing-sheet interconnects were designed and manufactured, and dense arrays of strain gauge sensors were assembled onto the interconnects. In total, four (two for each design type) strain sensing sheets were created and tested, which were sensitive to strain at virtually every point over the whole sensing sheet area. The sensing sheets were bonded to small-scale steel plates, which had a notch on the boundary so that fatigue cracks could be generated under cyclic loading. The fatigue tests were carried out at the Carleton Laboratory of Columbia University, and the steel plates were attached through a fixture to the loading machine that applied cyclic fatigue load. Fatigue cracks then occurred and propagated across the steel plates, leading to the failure of these test samples. The strain sensor that was close to the notch successfully detected the initialization of fatigue crack and localized the damage on the plate. The strain sensor that was away from the crack successfully detected the propagation of fatigue crack based on the time history of measured strain. Overall, the results of the fatigue tests validated general principles of the strain sensing sheets for crack detection.

Asthma in Adults Fact Sheet

MedlinePlus

... American Lung Association Epidemiology and Statistics Unit using SPSS software. Center for Disease Control and Prevention. Behavioral ... American Lung Association Epidemiology and Statistics Unit using SPSS software. Centers for Disease Control and Prevention. National ...

An amyloid-forming peptide from the yeast prion Sup35 reveals a dehydrated β-sheet structure for amyloid

PubMed Central

Balbirnie, Melinda; Grothe, Robert; Eisenberg, David S.

2001-01-01

X-ray diffraction and other biophysical tools reveal features of the atomic structure of an amyloid-like crystal. Sup35, a prion-like protein in yeast, forms fibrillar amyloid assemblies intrinsic to its prion function. We have identified a polar peptide from the N-terminal prion-determining domain of Sup35 that exhibits the amyloid properties of full-length Sup35, including cooperative kinetics of aggregation, fibril formation, binding of the dye Congo red, and the characteristic cross-β x-ray diffraction pattern. Microcrystals of this peptide also share the principal properties of the fibrillar amyloid, including a highly stable, β-sheet-rich structure and the binding of Congo red. The x-ray powder pattern of the microcrystals, extending to 0.9-Å resolution, yields the unit cell dimensions of the well-ordered structure. These dimensions restrict possible atomic models of this amyloid-like structure and demonstrate that it forms packed, parallel-stranded β-sheets. The unusually high density of the crystals shows that the packed β-sheets are dehydrated, despite the polar character of the side chains. These results suggest that amyloid is a highly intermolecularly bonded, dehydrated array of densely packed β-sheets. This dry β-sheet could form as Sup35 partially unfolds to expose the peptide, permitting it to hydrogen-bond to the same peptide of other Sup35 molecules. The implication is that amyloid-forming units may be short segments of proteins, exposed for interactions by partial unfolding. PMID:11226247

Living with Volcanoes: Year Eleven Teaching Resource Unit.

ERIC Educational Resources Information Center

Le Heron, Kiri; Andrews, Jill; Hooks, Stacey; Larnder, Michele; Le Heron, Richard

2000-01-01

Presents a unit on volcanoes and experiences with volcanoes that helps students develop geography skills. Focuses on four volcanoes: (1) Rangitoto Island; (2) Lake Pupuke; (3) Mount Smart; and (4) One Tree Hill. Includes an answer sheet and resources to use with the unit. (CMK)

Test Driven Development of a Parameterized Ice Sheet Component

NASA Astrophysics Data System (ADS)

Clune, T.

2011-12-01

Test driven development (TDD) is a software development methodology that offers many advantages over traditional approaches including reduced development and maintenance costs, improved reliability, and superior design quality. Although TDD is widely accepted in many software communities, the suitability to scientific software is largely undemonstrated and warrants a degree of skepticism. Indeed, numerical algorithms pose several challenges to unit testing in general, and TDD in particular. Among these challenges are the need to have simple, non-redundant closed-form expressions to compare against the results obtained from the implementation as well as realistic error estimates. The necessity for serial and parallel performance raises additional concerns for many scientific applicaitons. In previous work I demonstrated that TDD performed well for the development of a relatively simple numerical model that simulates the growth of snowflakes, but the results were anecdotal and of limited relevance to far more complex software components typical of climate models. This investigation has now been extended by successfully applying TDD to the implementation of a substantial portion of a new parameterized ice sheet component within a full climate model. After a brief introduction to TDD, I will present techniques that address some of the obstacles encountered with numerical algorithms. I will conclude with some quantitative and qualitative comparisons against climate components developed in a more traditional manner.

The effect of mesenchymal stem cell sheets on structural allograft healing of critical sized femoral defects in mice.

PubMed

Long, Teng; Zhu, Zhenan; Awad, Hani A; Schwarz, Edward M; Hilton, Matthew J; Dong, Yufeng

2014-03-01

Structural bone allografts are widely used in the clinic to treat critical sized bone defects, despite lacking the osteoinductive characteristics of live autografts. To address this, we generated revitalized structural allografts wrapped with mesenchymal stem/progenitor cell (MSC) sheets, which were produced by expanding primary syngenic bone marrow derived cells on temperature-responsive plates, as a tissue-engineered periosteum. In vitro assays demonstrated maintenance of the MSC phenotype in the sheets, suggesting that short-term culturing of MSC sheets is not detrimental. To test their efficacy in vivo, allografts wrapped with MSC sheets were transplanted into 4-mm murine femoral defects and compared to allografts with direct seeding of MSCs and allografts without cells. Evaluations consisted of X-ray plain radiography, 3D microCT, histology, and biomechanical testing at 4- and 6-weeks post-surgery. Our findings demonstrate that MSC sheets induce prolonged cartilage formation at the graft-host junction and enhanced bone callus formation, as well as graft-host osteointegration. Moreover, a large periosteal callus was observed spanning the allografts with MSC sheets, which partially mimics live autograft healing. Finally, biomechanical testing showed a significant increase in the structural and functional properties of MSC sheet grafted femurs. Taken together, MSC sheets exhibit enhanced osteogenicity during critical sized bone defect repair, demonstrating the feasibility of this tissue engineering solution for massive allograft healing. Copyright © 2013 Elsevier Ltd. All rights reserved.

New Modelling of Localized Necking in Sheet Metal Stretching

NASA Astrophysics Data System (ADS)

Bressan, José Divo

2011-01-01

Present work examines a new mathematical model to predict the onset of localized necking in the industrial processes of sheet metal forming such as biaxial stretching. Sheet metal formability is usually assessed experimentally by testing such as the Nakajima test to obtain the Forming Limit Curve, FLC, which is an essential material parameter necessary to numerical simulations by FEM. The Forming Limit Diagram or "Forming Principal Strain Map" shows the experimental FLC which is the plot of principal true strains in the sheet metal surface, ɛ1 and ɛ2, occurring at critical points obtained in laboratory formability tests or in the fabrication process. Two types of undesirable rupture mechanisms can occur in sheet metal forming products: localized necking and shear induced fracture. Therefore, two kinds of limit strain curves can be plotted: the local necking limit curve FLC-N and the shear fracture limit curve FLC-S. Localized necking is theoretically anticipated to initiate at a thickness defect ƒin = hib/hia inside the grooved sheet thickness hia, but only at the instability point of maximum load. The inception of grooving on the sheet surface evolves from instability point to localized necking and final rupture, during further sheet metal straining. Work hardening law is defined for a strain and strain rate material by the effective stress σ¯ = σo(1+βɛ¯)n???ɛM. The average experimental hardening law curve for tensile tests at 0°, 45° and 90°, assuming isotropic plasticity, was used to analyze the plasticity behavior during the biaxial stretching of sheet metals. Theoretical predicted curves of local necking limits are plotted in the positive quadrant of FPSM for different defect values ƒin and plasticity parameters. Limit strains are obtained from a software developed by the author. Some experimental results of forming limit curve obtained from experiments for IF steel sheets are compared with the theoretical predicted curves: the correlation is good.

Test of superplastically formed corrugated aluminum compression specimens with beaded webs

NASA Technical Reports Server (NTRS)

Davis, Randall C.; Royster, Dick M.; Bales, Thomas T.; James, William F.; Shinn, Joseph M., Jr.

1991-01-01

Corrugated wall sections provide a highly efficient structure for carrying compressive loads in aircraft and spacecraft fuselages. The superplastic forming (SPF) process offers a means to produce complex shells and panels with corrugated wall shapes. A study was made to investigate the feasibility of superplastically forming 7475-T6 aluminum sheet into a corrugated wall configuration and to demonstrate the structural integrity of the construction by testing. The corrugated configuration selected has beaded web segments separating curved-cap segments. Eight test specimens were fabricated. Two specimens were simply a single sheet of aluminum superplastically formed to a beaded-web, curved-cap corrugation configuration. Six specimens were single-sheet corrugations modified by adhesive bonding additional sheet material to selectively reinforce the curved-cap portion of the corrugation. The specimens were tested to failure by crippling in end compression at room temperature.

A Randomized Rounding Approach for Optimization of Test Sheet Composing and Exposure Rate Control in Computer-Assisted Testing

ERIC Educational Resources Information Center

Wang, Chu-Fu; Lin, Chih-Lung; Deng, Jien-Han

2012-01-01

Testing is an important stage of teaching as it can assist teachers in auditing students' learning results. A good test is able to accurately reflect the capability of a learner. Nowadays, Computer-Assisted Testing (CAT) is greatly improving traditional testing, since computers can automatically and quickly compose a proper test sheet to meet user…

New stratigraphic, chronologic, and magnetic fabric constraints for Neogene and Quaternary ignimbrites in the Central Andes (South Peru)

NASA Astrophysics Data System (ADS)

De La Rupelle, A.; Thouret, J. C.; Cubukcu, H. E.; Jicha, B.; Bréard, E.; Gerbe, M.-C.; Le Pennec, J.-L.; Diot, H.; Boivin, P.

2012-04-01

Central Andean deformation history in southern Peru is recorded in Neogene volcanic units of Ocoña and Cotahuasi canyons that cut across the western Cordillera. Acceleration (<25 Ma) of uplift in the region is reflected in the Neogene epiclastic deposits with interspersed and subsequent rhyolitic ignimbrites between 24.6 and 1.37 Ma. Large-volume (>100 km3) Nazca (c.24.6 Ma), Alpabamba (19.4-18.0 Ma), and Huaylillas (14.25-12.7 Ma) ignimbrite sheets preceded the canyon incision, whereas sheets of smaller volume (<50 km3), Caraveli (9.5-8.9 Ma), Lower (5.13-3.6 Ma) and Upper Sencca (c.2 Ma) and Las Lomas (c.1.56-1.37 Ma), were deposited during canyon incision and are interspersed with Lower and Upper Barroso lava flows. The Alpabamba compound ignimbrite sheets comprise a vitrophyre at the base, grading into a strongly welded, eutaxitic, crystal-rich facies overlain by a thick, multi-bedded ash-flow tuff and a lithic-rich, indurated flow unit. The Huaylillas ignimbrite sheet comprises a strongly welded, crystal-rich, lithic-poor, columnar lithofacies, with devitrified pumice. The Caraveli ignimbrite sheet has a jointed vitrophyre overlain by a welded, blocky, crystal-rich flow unit. A vacuolar, saccharolytic unit forms the top of the sequence. The Lower Sencca ignimbrite sheet comprises of a basal vitrophyre and a slightly welded, fibrous pumice-rich flow unit, which grades into a welded, vapor-phase unit that contains more crystals than pumice and lithics. The Upper Sencca ignimbrite sheet consists of a black vitrophyre, grading into a strongly welded, crystal-rich, eutaxitic cooling unit. The latter is capped by a slightly welded unit, and an indurated pumice-rich, crystal-poor vapour-phase facies. Quaternary valley-fill termed Las Lomas consists of unwelded, crystal-poor pumice-flow deposits. Eighteen new 40Ar/39Ar analyses have been carried out on feldspar/glass separates from pumice and lavas. Results for the Caraveli ignimbrite (9.35±0.06 Ma), Upper Barroso lavas (2.24±0.45 Ma) and Upper Sencca ignimbrite (2.00-2.06±0.09 Ma) are in good agreement with previous data. New ages for the Lower Barroso lavas (7.32±0.05; 5.36±0.12 Ma) and Lower Sencca ignimbrites (5.13±0.01, 5.09±0.03, 4.65±0.11, 4.36 ± 0.16) extend their temporal history towards older times. Lower Barroso lava flow activity occurred as early as~7.3 and lasted until 5.4 Ma just before the Lower Sencca eruptions. The Lower Sencca ignimbrites spanned at least 1.5 Ma and are larger and more widespread than the Upper Sencca ignimbrites, which may have formed in one pulse around 2 Ma. The Anisotropy of Magnetic Susceptibility (AMS) method and the magnetic fabric at 24 sites have been used to indicate flow directions and to infer the source location of the rhyolitic ignimbrites. Mean directions and confidence cones were calculated using Bingham statistics. Most AMS ellipsoids are oblate with near-vertical, slightly imbricated minimum susceptibility directions. The magnetic signal is dominantly carried by coarse multi-domain and a few fine single-domain grains of titanomagnetite. Inferred transport directions based on AMS results reveal that the source of Huaylillas, Lower Sencca and Upper Sencca units is probably located below the Nevado Coropuna volcano. The source of the Caraveli unit points to a depression W of Nevado Sara Sara. The Alpabamba source could not be clearly determined. Keywords: ignimbrites, Peru, stratigraphy, chronology, AMS, fabric, Neogene, Quaternary.

Laser Indirect Shock Welding of Fine Wire to Metal Sheet.

PubMed

Wang, Xiao; Huang, Tao; Luo, Yapeng; Liu, Huixia

2017-09-12

The purpose of this paper is to present an advanced method for welding fine wire to metal sheet, namely laser indirect shock welding (LISW). This process uses silica gel as driver sheet to accelerate the metal sheet toward the wire to obtain metallurgical bonding. A series of experiments were implemented to validate the welding ability of Al sheet/Cu wire and Al sheet/Ag wire. It was found that the use of a driver sheet can maintain high surface quality of the metal sheet. With the increase of laser pulse energy, the bonding area of the sheet/wire increased and the welding interfaces were nearly flat. Energy dispersive spectroscopy (EDS) results show that the intermetallic phases were absent and a short element diffusion layer which would limit the formation of the intermetallic phases emerging at the welding interface. A tensile shear test was used to measure the mechanical strength of the welding joints. The influence of laser pulse energy on the tensile failure modes was investigated, and two failure modes, including interfacial failure and failure through the wire, were observed. The nanoindentation test results indicate that as the distance to the welding interface decreased, the microhardness increased due to the plastic deformation becoming more violent.

Bedrock geologic map of Vermont

USGS Publications Warehouse

Ratcliffe, Nicholas M.; Stanley, Rolfe S.; Gale, Marjorie H.; Thompson, Peter J.; Walsh, Gregory J.; With contributions by Hatch, Norman L.; Rankin, Douglas W.; Doolan, Barry L.; Kim, Jonathan; Mehrtens, Charlotte J.; Aleinikoff, John N.; McHone, J. Gregory; Cartography by Masonic, Linda M.

2011-01-01

The Bedrock Geologic Map of Vermont is the result of a cooperative agreement between the U.S. Geological Survey (USGS) and the State of Vermont. The State's complex geology spans 1.4 billion years of Earth's history. The new map comes 50 years after the most recent map of the State by Charles G. Doll and others in 1961 and a full 150 years since the publication of the first geologic map of Vermont by Edward Hitchcock and others in 1861. At a scale of 1:100,000, the map shows an uncommon level of detail for State geologic maps. Mapped rock units are primarily based on lithology, or rock type, to facilitate derivative studies in multiple disciplines. The 1961 map was compiled from 1:62,500-scale or smaller maps. The current map was created to integrate more detailed (1:12,000- to 1:24,000-scale) modern and older (1:62,500-scale) mapping with the theory of plate tectonics to provide a framework for geologic, tectonic, economic, hydrogeologic, and environmental characterization of the bedrock of Vermont. The printed map consists of three oversize sheets (52 x 76 inches). Sheets 1 and 2 show the southern and northern halves of Vermont, respectively, and can be trimmed and joined so that the entire State can be displayed as a single entity. These sheets also include 10 cross sections and a geologic structure map. Sheet 3 on the front consists of descriptions of 486 map units, a correlation of map units, and references cited. Sheet 3 on the back features a list of the 195 sources of geologic map data keyed to an index map of 7.5-minute quadrangles in Vermont, as well as a table identifying ages of rocks dated by uranium-lead zircon geochronology.

Acrolein Yields in Mainstream Smoke From Commercial Cigarette and Little Cigar Tobacco Products.

PubMed

Cecil, Todd L; Brewer, Tim M; Young, Mimy; Holman, Matthew R

2017-07-01

Many carbonyls are produced from the combustion of tobacco products and many of these carbonyls are harmful or potentially harmful constituents of mainstream cigarette smoke. One carbonyl of particular interest is acrolein, which is formed from the incomplete combustion of organic matter and the most significant contributor to non-cancer respiratory effects from cigarette smoke. Sheet-wrapped cigars, also known as "little cigars," are a type of tobacco products that have not been extensively investigated in literature. This study uses standard cigarette testing protocols to determine the acrolein yields from sheet-wrapped cigars. Sheet-wrapped cigar and cigarette products were tested by derivatizing the mainstream smoke with 2,4-dinitrophenylhydrazine (DNPH) solution and then quantifying the derivatives using conventional analytical systems. The results demonstrate that sheet-wrapped cigars can be tested for acrolein yields in mainstream smoke using the same methods used for the evaluation of cigarettes. The variability in the sheet-wrapped cigars and cigarettes under the International Organization for Standardization smoking regimen is statistically similar at the 95% confidence interval; however, increased variability is observed for sheet-wrapped cigar products under the Health Canada Intense (CI) smoking regimen. The amount of acrolein released by smoking sheet-wrapped cigars can be measured using standard smoking regimen currently used for cigarettes. The sheet-wrapped cigars were determined to yield similar quantity of acrolein from commercial cigarette products using two standard smoking regimens. This article reports on the measured quantity of acrolein from 15 commercial sheet-wrapped cigars using a validated standard smoking test method that derivatizes acrolein in the mainstream smoke with DNPH solution, and uses Liquid Chromatography/Ultra-Violet Detection (LC/UV) for separation and detection. These acrolein yields were similar to the levels found in the smoke from 35 commercial cigarette products measured in the same manner. Although sheet-wrapped cigar data were slightly more variable than those found for the cigarette data, this article reports that the production of acrolein is similar to cigarettes. The results demonstrate that sheet-wrapped cigars can be tested for acrolein yields in mainstream smoke using the same methods used for the evaluation of cigarettes. Published by Oxford University Press on behalf of the Society for Research on Nicotine and Tobacco 2017. This work is written by (a) US Government employee(s) and is in the public domain in the US.

Sensing sheet: the response of full-bridge strain sensors to thermal variations for detecting and characterizing cracks

NASA Astrophysics Data System (ADS)

Tung, S.-T.; Glisic, B.

2016-12-01

Sensing sheets based on large-area electronics consist of a dense array of unit strain sensors. This new technology has potential for becoming an effective and affordable monitoring tool that can identify, localize and quantify surface damage in structures. This research contributes to their development by investigating the response of full-bridge unit strain sensors to thermal variations. Overall, this investigation quantifies the effects of temperature on thin-film full-bridge strain sensors monitoring uncracked and cracked concrete. Additionally, an empirical formula is developed to estimate crack width given an observed strain change and a measured temperature change. This research led to the understanding of the behavior of full-bridge strain sensors installed on cracked concrete and exposed to temperature variations. It proves the concept of the sensing sheet and its suitability for application in environments with variable temperature.

Self-Contained Math Manual. Teacher's Guide.

ERIC Educational Resources Information Center

Grant, Shelia I.

This instructional manual consists of 11 competency-based units for a mathematics course for trade and industrial programs in Texas. Each instructional unit includes the following basic components: unit and specific objectives, notes to the instructor (outline of steps to follow in accomplishing specific objectives), information sheets,…

Forestry. Teacher Edition.

ERIC Educational Resources Information Center

Oklahoma State Dept. of Vocational and Technical Education, Stillwater. Curriculum and Instructional Materials Center.

This curriculum is designed to provide training in skills used by technicians and foresters throughout the world who plant, care for, and harvest trees. It contains 16 units. Each instructional unit includes some or all of the basic components of a unit of instruction: performance objectives, suggested activities, handouts, information sheets,…

Analytical and experimental investigation of fatigue in a sheet specimen with an interference-fit bolt

NASA Technical Reports Server (NTRS)

Crews, J. H., Jr.

1975-01-01

A fatigue analysis, based on finite-element calculations and fatigue tests, was conducted for an aluminum-alloy sheet specimen with a steel interference-fit bolt. The stress analysis of the region near the bolt hole showed that the beneficial effect of an interference-fit bolt can be interpreted as the combined result of two effects: (1) load transfer through the bolt and (2) the compressive interference stresses in the sheet. Results of the fatigue tests show that progressively higher interference levels produced longer fatigue lives. The tests also show that a high level of interference prevents fretting at the bolt-sheet interface and that interferences larger than this level produced little additional improvement in fatigue life.

Solid-state and fusion resistance spot welding of TD-NiCr sheet

NASA Technical Reports Server (NTRS)

Moore, T. J.

1973-01-01

By using specially processed TD-NiCr sheet in both 0.4-mm (0.015-in.) and 1.6-mm (0.062-in.) thicknesses and carefully selected welding procedures, solid state resistance spot welds were produced which, after postheating at 1200 C, were indistinguishable from the parent material. Stress-rupture shear tests of single-spot lap joints in 0.4-mm (0.015-in.) thick sheet showed that these welds were as strong as the parent material. Similar results were obtained in tensile-shear tests at room temperature and 1100 C and in fatigue tests. Conventional fusion spot welds in commercial sheet were unsatisfactory because of poor stress-rupture shear properties resulting from metallurgical damage to the parent material.

76 FR 77855 - Detroit Edison Company; Notice of Availability of Errata Sheet for the Draft Environmental Impact...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-14

... NUCLEAR REGULATORY COMMISSION [Docket No. 52-033; NRC-2008-0566] Detroit Edison Company; Notice of Availability of Errata Sheet for the Draft Environmental Impact Statement for a Combined License for Unit 3 at the Enrico Fermi Atomic Power Plant Site Notice is hereby given that the U.S. Nuclear Regulatory...

76 FR 58536 - Tin- and Chromium-Coated Steel Sheet From Japan; Notice of Commission Determination To Conduct a...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-21

... INTERNATIONAL TRADE COMMISSION [Investigation No. 731-TA-860 (Second Review)] Tin- and Chromium... Concerning the Antidumping Duty Order on Tin- and Chromium-Coated Steel Sheet From Japan AGENCY: United.... 1675(c)(5)) to determine whether revocation of the antidumping duty order on tin- and chromium-coated...

Topographical atlas sheets

USGS Publications Warehouse

Wheeler, George Montague

1876-01-01

The following topographical atlas sheets, accompanying Appendix J.J. of the Annual Report of the Chief of Engineers, U.S. Army-being Annual Report upon U. S. Geographical Surveys-have been published during the fiscal year ending June 30, 1876, and are a portion of the series projected to embrace the territory of the United States lying west of the 100th meridian.

A Look at Constitutional Checks and Balances: Study Sheets for U.S. History.

ERIC Educational Resources Information Center

Scott, Nancy

This document is intended as a resource guide for teachers to use in helping students to understand how the United States system of government operates. It examines the background, historical application, and current debate concerning the principle of checks and balances. Ten study sheets feature various figures and episodes prominently associated…

75 FR 81308 - Stainless Steel Sheet And Strip From Germany, Italy, Japan, Korea, Mexico, And Taiwan

Federal Register 2010, 2011, 2012, 2013, 2014

2010-12-27

...)] Stainless Steel Sheet And Strip From Germany, Italy, Japan, Korea, Mexico, And Taiwan AGENCY: United States... and strip from Germany, Italy, Japan, Korea, Mexico, and Taiwan. SUMMARY: The Commission hereby gives... strip from Germany, Italy, Japan, Korea, Mexico, and Taiwan would be likely to lead to continuation or...

College Measures 2-Year and 4-Year Data Tools. Fact Sheet

ERIC Educational Resources Information Center

Institute for Higher Education Policy, 2016

2016-01-01

College Measures was established in 2010 as a partnership between the American Institutes for Research (AIR) and Matrix Knowledge Group (now Optimity Advisors). In 2016, College Measures became fully owned by AIR. It remains focused on using data to drive improvement in higher education outcomes in the United States. This fact sheet presents a…

A Microsample Tensile Test Application: Local Strength of Impact Welds Between Sheet Metals

NASA Astrophysics Data System (ADS)

Benzing, J. T.; He, M.; Vivek, A.; Taber, G. A.; Mills, M. J.; Daehn, G. S.

2017-03-01

Microsample tensile testing was conducted to evaluate the quality of impact welds created by vaporizing foil actuator welding. Tensile test samples with a gauge length of 0.6 mm were electro-discharge machined out of welds created between 1-mm-thick aluminum alloy type 6061 (AA6061) sheets and 6-mm-thick copper (Cu110) plates. Aluminum sheets were used as flyers, while copper plates acted as targets. Flyer sheets in T6 as well as T4 temper conditions were utilized to create welds. Some of the welds made with T4 temper flyers were heat treated to a T6 temper. It was found that the welds made with T4 temper flyers were slightly stronger (max. of 270 MPa) than those produced with T6 temper flyers. Generally, failure propagated in a brittle manner across the weld interface; however, elemental mapping reveals material transfer on either member of the welded system. This work proves the feasibility to apply microsample tensile testing to assess impact welding, even when conducted with flyer sheets of 1 mm or less, and provides insight that is complementary to other test methods.

Evaluation of the Transient Liquid Phase (TLP) Bonding Process for Ti3Al-Based Honeycomb Core Sandwich Structure

NASA Technical Reports Server (NTRS)

Bird, R. Keith; Hoffman, Eric K.

1998-01-01

The suitability of using transient liquid phase (TLP) bonding to fabricate honeycomb core sandwich panels with Ti-14Al-21Nb (wt%) titanium aluminide (T3Al) face sheets for high-temperature hypersonic vehicle applications was evaluated. Three titanium alloy honeycomb cores and one Ti3Al alloy honeycomb core were investigated. Edgewise compression (EWC) and flatwise tension (FWT) tests on honeycomb core sandwich specimens and tensile tests of the face sheet material were conducted at temperatures ranging from room temperature to 1500 F. EWC tests indicated that the honeycomb cores and diffusion bonded joints were able to stabilize the face sheets up to and beyond the face sheet compressive yield strength for all temperatures investigated. The specimens with the T3Al honeycomb core produced the highest FWT strengths at temperatures above 1000 F. Tensile tests indicated that TLP processing conditions resulted in decreases in ductility of the Ti-14Al-21Nb face sheets. Microstructural examination showed that the side of the face sheets to which the filler metals had been applied was transformed from equiaxed alpha2 grains to coarse plates of alpha2 with intergranular Beta. Fractographic examination of the tensile specimens showed that this transformed region was dominated by brittle fracture.

Property Criteria for Automotive Al-Mg-Si Sheet Alloys

PubMed Central

Prillhofer, Ramona; Rank, Gunther; Berneder, Josef; Antrekowitsch, Helmut; Uggowitzer, Peter J.; Pogatscher, Stefan

2014-01-01

In this study, property criteria for automotive Al-Mg-Si sheet alloys are outlined and investigated in the context of commercial alloys AA6016, AA6005A, AA6063 and AA6013. The parameters crucial to predicting forming behavior were determined by tensile tests, bending tests, cross-die tests, hole-expansion tests and forming limit curve analysis in the pre-aged temper after various storage periods following sheet production. Roping tests were performed to evaluate surface quality, for the deployment of these alloys as an outer panel material. Strength in service was also tested after a simulated paint bake cycle of 20 min at 185 °C, and the corrosion behavior was analyzed. The study showed that forming behavior is strongly dependent on the type of alloy and that it is influenced by the storage period after sheet production. Alloy AA6016 achieves the highest surface quality, and pre-ageing of alloy AA6013 facilitates superior strength in service. Corrosion behavior is good in AA6005A, AA6063 and AA6016, and only AA6013 shows a strong susceptibility to intergranular corrosion. The results are discussed below with respect to the chemical composition, microstructure and texture of the Al-Mg-Si alloys studied, and decision-making criteria for appropriate automotive sheet alloys for specific applications are presented. PMID:28788119

An Innovative Parallel Test Sheet Composition Approach to Meet Multiple Assessment Criteria for National Tests

ERIC Educational Resources Information Center

Hwang, Gwo-Jen; Chu, Hui-Chun; Yin, Peng-Yeng; Lin, Ji-Yu

2008-01-01

The national certification tests and entrance examinations are the most important tests for proving the ability or knowledge level of a person. To accurately evaluate the professional skills or knowledge level, the composed test sheets must meet multiple assessment criteria such as the ratio of relevant concepts to be evaluated and the estimated…

Investigation on local ductility of 6xxx-aluminium sheet alloys

NASA Astrophysics Data System (ADS)

Henn, P.; Liewald, M.; Sindel, M.

2017-09-01

Within the scope of this paper influence of localization of loading conditions on the ductility of two different 6xxx-aluminium sheet alloys is investigated. In order to improve the prediction of sheet material crash performance, material parameters based on uniaxial tensile and notched tensile tests are determined with varying consolidation areas. Especially evaluation methods based on the localized necking behaviour in tensile tests are investigated. The potential of local ductility characterisation is validated with results of Edge-Compression Tests (ECT) which applies load conditions that occur in actual crash events.

Passive radon/thoron personal dosimeter using an electrostatic collector and a diffused-junction detector

NASA Astrophysics Data System (ADS)

Bigu, J.; Raz, R.

1985-01-01

A solid-state alpha dosimeter has been designed and tested suitable for personal and environmental radon/thoron monitoring. The dosimeter basically consists of an electrostatic collector and an alpha-particle counting system with spectroscopy capabilities. The sensitive volume (˜20 cm3) of the electrostatic collector consists of a cylindrically shaped metal wire screen and a diffused-junction silicon alpha-detector covered with a thin aluminized Mylar sheet. A dc voltage (˜500 V) is applied between the wire screen and the Mylar sheet, with the latter held at negative potential relative to the former. Data can be retrieved during or after sampling by means of a microcomputer (Epson HX20) via a RS-232 communication interface unit. The dosimeter has been calibrated in a large (26 m3) radon/thoron test facility. A linear relationship was found between the dosimeter's alpha-count and both radon gas concentration and radon daughter working level. The dosimeter is mounted on top of an ordinary miner's cap lamp battery and is ideally suited for personal monitoring in underground uranium mines and other working areas. The dosimeter presented here is a considerably improved version of an earlier prototype.

Unit Charge, First Trial Materials, Inspection Set.

ERIC Educational Resources Information Center

Australian Science Education Project, Toorak, Victoria.

The first trial edition of the Australian Science Education Project unit introducing the concepts of electrical charge consists of a student workbook, question booklet and a response sheet, and a booklet containing answers to the questions in the workbook and question booklet. The teacher's guide outlines the unit, lists suggested teaching…

Introduction to Surgical Technology. Teacher Edition.

ERIC Educational Resources Information Center

Bushey, Vicki; And Others

This instructor's manual contains 14 units of instruction for a course on surgical technology designed to include the entry-level competencies students need to enter any of the more advanced surgical technology courses. Each unit includes some or all of the following basic components of a unit of instruction: objective sheet, suggested activities…

Solar Energy Applications for Agriculture. A Curriculum Guide.

ERIC Educational Resources Information Center

Nebraska Univ., Lincoln. Dept. of Agricultural Education.

This curriculum guide contains five units for a course in solar energy applications for vocational agriculture. Each unit is organized in a format containing some or all of the following materials: unit objective, specific objectives, suggested instructor and student activities, list of instructional materials, assignment sheets, answers to…

New Mexico State Secondary School Science-Based Nutrition Curriculum.

ERIC Educational Resources Information Center

Ecklund, Susan, Ed.; Smalley, Katherine, Ed.

This curriculum guide provides instructional materials for a 10-unit secondary-level science-based nutrition course. Each unit contains some or all of the following components: a summary sheet for each function, including generalizations with corresponding objectives, additional learning activities, and additional resources; unit outline; pretest;…

Surgical Techniques. Second Edition. Teacher Edition.

ERIC Educational Resources Information Center

Bushey, Vicki; And Others

This instructor's manual contains 18 units of instruction for a course on surgical technology designed to include the entry-level competencies students need as a surgical technologist. Each unit includes some or all of the following basic components of a unit of instruction: objective sheet, suggested activities for the teacher, assignment sheets…

Integrating personalized medical test contents with XML and XSL-FO.

PubMed

Toddenroth, Dennis; Dugas, Martin; Frankewitsch, Thomas

2011-03-01

In 2004 the adoption of a modular curriculum at the medical faculty in Muenster led to the introduction of centralized examinations based on multiple-choice questions (MCQs). We report on how organizational challenges of realizing faculty-wide personalized tests were addressed by implementation of a specialized software module to automatically generate test sheets from individual test registrations and MCQ contents. Key steps of the presented method for preparing personalized test sheets are (1) the compilation of relevant item contents and graphical media from a relational database with database queries, (2) the creation of Extensible Markup Language (XML) intermediates, and (3) the transformation into paginated documents. The software module by use of an open source print formatter consistently produced high-quality test sheets, while the blending of vectorized textual contents and pixel graphics resulted in efficient output file sizes. Concomitantly the module permitted an individual randomization of item sequences to prevent illicit collusion. The automatic generation of personalized MCQ test sheets is feasible using freely available open source software libraries, and can be efficiently deployed on a faculty-wide scale.

Development of a Cavitation Erosion Resistant Advanced Material System

DTIC Science & Technology

2005-11-01

Sheet EPD M results .............................................................................. 47 Figure 5.11 - EPDM rubber samples, sheet (left...Testing The long test times of EPDM rubber and other durable elastomer samples created a need for overnight testing capability. In the original test setup...seals, adhesives and molded flexible parts. Common examples of elastomers include natural and synthetic rubber , silicone, neoprene, EPDM , polyurethane

Recommended specifications and a tentative testing procedure for reflective sheeting.

DOT National Transportation Integrated Search

1977-01-01

The Department spends approximately a half million dollars annually on reflective sheeting for highway signs. For years this sheeting has been purchased primarily from one manufacturer, because of the inability of other firms to produce a competitive...

An effective self-assessment based on concept map extraction from test-sheet for personalized learning

NASA Astrophysics Data System (ADS)

Liew, Keng-Hou; Lin, Yu-Shih; Chang, Yi-Chun; Chu, Chih-Ping

2013-12-01

Examination is a traditional way to assess learners' learning status, progress and performance after a learning activity. Except the test grade, a test sheet hides some implicit information such as test concepts, their relationships, importance, and prerequisite. The implicit information can be extracted and constructed a concept map for considering (1) the test concepts covered in the same question means these test concepts have strong relationships, and (2) questions in the same test sheet means the test concepts are relative. Concept map has been successfully employed in many researches to help instructors and learners organize relationships among concepts. However, concept map construction depends on experts who need to take effort and time for the organization of the domain knowledge. In addition, the previous researches regarding to automatic concept map construction are limited to consider all learners of a class, which have not considered personalized learning. To cope with this problem, this paper proposes a new approach to automatically extract and construct concept map based on implicit information in a test sheet. Furthermore, the proposed approach also can help learner for self-assessment and self-diagnosis. Finally, an example is given to depict the effectiveness of proposed approach.

Explosive Testing of Class 1.3 Rocket Booster Propellant

DTIC Science & Technology

1994-08-01

molds were lined with 0.025 mm (0.001 in.) Velostat conductive plastic sheet and sprayed with a mold release that dried leaving fine Teflon powder... Velostat sheet (0.03 in.) was wrapped around the sample and grounded for improved electrostatic safety. Similar to previous cylinder tests, the...layer of thin Velostat plastic sheet, its contribution to camera viewing distortion of the flame front is not known. Overall, an average velocity over

Factors governing hole expansion ratio of steel sheets with smooth sheared edge

NASA Astrophysics Data System (ADS)

Yoon, Jae Ik; Jung, Jaimyun; Lee, Hak Hyeon; Kim, Gyo-Sung; Kim, Hyoung Seop

2016-11-01

Stretch-flangeability measured using hole expansion test (HET) represents the ability of a material to form into a complex shaped component. Despite its importance in automotive applications of advanced high strength steels, stretch-flangeability is a less known sheet metal forming property. In this paper, we investigate the factors governing hole expansion ratio (HER) by means of tensile test and HET. We correlate a wide range of tensile properties with HERs of steel sheet specimens because the stress state in the hole edge region during the HET is almost the same as that of the uniaxial tensile test. In order to evaluate an intrinsic HER of steel sheet specimens, the initial hole of the HET specimen is produced using a milling process after punching, which can remove accumulated shearing damage and micro-void in the hole edge region that is present when using the standard HER evaluation method. It was found that the intrinsic HER of steel sheet specimens was proportional to the strain rate sensitivity exponent and post uniform elongation.

Sakacin-A antimicrobial packaging for decreasing Listeria contamination in thin-cut meat: preliminary assessment.

PubMed

Barbiroli, Alberto; Musatti, Alida; Capretti, Giorgio; Iametti, Stefania; Rollini, Manuela

2017-02-01

Minimally processed ready-to-eat products are considered a high-risk food because of the possibility of contamination with pathogenic bacteria, including Listeria monocytogenes from the animal reservoir, and the minimal processing they undergo. In this study, a sakacin-A anti-Listeria active package was developed and tested on thin-cut veal meat slices (carpaccio). Enriched food-grade sakacin-A was obtained from a cell-free supernatant of a Lactobacillus sakei culture and applied (0.63 mg cm -2 ) onto the surface of polyethylene-coated paper sheets to obtain an active antimicrobial package. The coating retained antimicrobial features, indicating that the process did not affect sakacin-A functionality, as evidenced in tests carried out in vitro. Thin-cut veal meat slices inoculated with Listeria innocua (a surrogate of pathogenic L. monocytogenes) were laid on active paper sheets. After 48 h incubation at 4 °C, the Listeria population was found to be 1.5 log units lower with respect to controls (3.05 vs 4.46 log colony-forming units (CFU) g -1 ). This study demonstrates the possibility of using an antimicrobial coating containing sakacin-A to inhibit or decrease the Listeria population in ready-to-eat products, thus lowering the risk of food-related diseases. © 2016 The Authors. Journal of The Science of Food and Agriculture published by John Wiley & Sons Ltd on behalf of Society of Chemical Industry. © 2016 The Authors. Journal of The Science of Food and Agriculture published by John Wiley & Sons Ltd on behalf of Society of Chemical Industry.

Asian Americans: A Status Report. Fact Sheet for the Chairman, Select Committee on Hunger, House of Representatives.

ERIC Educational Resources Information Center

General Accounting Office, Washington, DC. Div. of Human Resources.

This fact sheet presents information on the status of Asians in the United States. The following sections are included: (1) "Introduction," which includes Asian American population statistics, and the objectives, scope, and methodology of the study; (2) "Overall Income and Employment Status Comparable With U.S. Population, But Varies Widely Among…

A Potential Theory for the Steady Separated Flow about an Aerofoil Section

DTIC Science & Technology

1988-02-01

Adviser (3 copies Doc Data sheet) Aircraft Maintenance and Flight Trials Unit Director of Naval Aircraft Engineering Director of Naval Air Warfare...Superintendent, Aircraft Maintenance and Repair Army Office Scientific Adviser - Army (Doc Data sheet only) Engineering Development Establishment, Library...Flight Group Library Technical Division Library Director General Aircraft Engineering - Air Force Director General Operational Requirements - Air Force

Divisions of geologic time-major chronostratigraphic and geochronologic units

USGS Publications Warehouse

,

2010-01-01

Effective communication in the geosciences requires consistent uses of stratigraphic nomenclature, especially divisions of geologic time. A geologic time scale is composed of standard stratigraphic divisions based on rock sequences and is calibrated in years. Over the years, the development of new dating methods and the refinement of previous methods have stimulated revisions to geologic time scales. Advances in stratigraphy and geochronology require that any time scale be periodically updated. Therefore, Divisions of Geologic Time, which shows the major chronostratigraphic (position) and geochronologic (time) units, is intended to be a dynamic resource that will be modified to include accepted changes of unit names and boundary age estimates. This fact sheet is a modification of USGS Fact Sheet 2007-3015 by the U.S. Geological Survey Geologic Names Committee.

Laser Indirect Shock Welding of Fine Wire to Metal Sheet

PubMed Central

Wang, Xiao; Huang, Tao; Luo, Yapeng; Liu, Huixia

2017-01-01

The purpose of this paper is to present an advanced method for welding fine wire to metal sheet, namely laser indirect shock welding (LISW). This process uses silica gel as driver sheet to accelerate the metal sheet toward the wire to obtain metallurgical bonding. A series of experiments were implemented to validate the welding ability of Al sheet/Cu wire and Al sheet/Ag wire. It was found that the use of a driver sheet can maintain high surface quality of the metal sheet. With the increase of laser pulse energy, the bonding area of the sheet/wire increased and the welding interfaces were nearly flat. Energy dispersive spectroscopy (EDS) results show that the intermetallic phases were absent and a short element diffusion layer which would limit the formation of the intermetallic phases emerging at the welding interface. A tensile shear test was used to measure the mechanical strength of the welding joints. The influence of laser pulse energy on the tensile failure modes was investigated, and two failure modes, including interfacial failure and failure through the wire, were observed. The nanoindentation test results indicate that as the distance to the welding interface decreased, the microhardness increased due to the plastic deformation becoming more violent. PMID:28895900

Using the Global Burden of Disease study to assist development of nation-specific fact sheets to promote prevention and control of hypertension and reduction in dietary salt: a resource from the World Hypertension League.

PubMed

Campbell, Norm R C; Lackland, Daniel T; Lisheng, Liu; Niebylski, Mark L; Nilsson, Peter M; Zhang, Xin-Hua

2015-03-01

Increased blood pressure and high dietary salt are leading risks for death and disability globally. Reducing the burden of both health risks are United Nations' targets for reducing noncommunicable disease. Nongovernmental organizations and individuals can assist by ensuring widespread dissemination of the best available facts and recommended interventions for both health risks. Simple but impactful fact sheets can be useful for informing the public, healthcare professionals, and policy makers. The World Hypertension League has developed fact sheets on dietary salt and hypertension but in many circumstances the greatest impact would be obtained from national-level fact sheets. This manuscript provides instructions and a template for developing fact sheets based on the Global Burden of Disease study and national survey data. ©2015 Wiley Periodicals, Inc.

Low-Velocity Impact Behavior of Sandwich Structures with Additively Manufactured Polymer Lattice Cores

NASA Astrophysics Data System (ADS)

Turner, Andrew J.; Al Rifaie, Mohammed; Mian, Ahsan; Srinivasan, Raghavan

2018-05-01

Sandwich panel structures are widely used in aerospace, marine, and automotive applications because of their high flexural stiffness, strength-to-weight ratio, good vibration damping, and low through-thickness thermal conductivity. These structures consist of solid face sheets and low-density cellular core structures, which are traditionally based upon honeycomb folded-sheet topologies. The recent advances in additive manufacturing (AM) or 3D printing process allow lattice core configurations to be designed with improved mechanical properties. In this work, the sandwich core is comprised of lattice truss structures (LTS). Two different LTS designs are 3D-printed using acrylonitrile butadiene styrene (ABS) and are tested under low-velocity impact loads. The absorption energy and the failure mechanisms of lattice cells under such loads are investigated. The differences in energy-absorption capabilities are captured by integrating the load-displacement curve found from the impact response. It is observed that selective placement of vertical support struts in the unit-cell results in an increase in the absorption energy of the sandwich panels.

Low-Velocity Impact Behavior of Sandwich Structures with Additively Manufactured Polymer Lattice Cores

NASA Astrophysics Data System (ADS)

Turner, Andrew J.; Al Rifaie, Mohammed; Mian, Ahsan; Srinivasan, Raghavan

2018-04-01

Sandwich panel structures are widely used in aerospace, marine, and automotive applications because of their high flexural stiffness, strength-to-weight ratio, good vibration damping, and low through-thickness thermal conductivity. These structures consist of solid face sheets and low-density cellular core structures, which are traditionally based upon honeycomb folded-sheet topologies. The recent advances in additive manufacturing (AM) or 3D printing process allow lattice core configurations to be designed with improved mechanical properties. In this work, the sandwich core is comprised of lattice truss structures (LTS). Two different LTS designs are 3D-printed using acrylonitrile butadiene styrene (ABS) and are tested under low-velocity impact loads. The absorption energy and the failure mechanisms of lattice cells under such loads are investigated. The differences in energy-absorption capabilities are captured by integrating the load-displacement curve found from the impact response. It is observed that selective placement of vertical support struts in the unit-cell results in an increase in the absorption energy of the sandwich panels.

Skills for Health Care Assistants. Supplemental Units for Health Care and Nurse Assistants Programs. Student Guide. Revised.

ERIC Educational Resources Information Center

Missouri Univ., Columbia. Instructional Materials Lab.

This guide contains 13 units to be used as a supplement in nurse assistant and health services courses. The units are self-paced and contain simplified line drawings, controlled text, vocabulary development, and mathematics practice exercises. Units consist of objectives, an introduction, a content outline, steps of a procedure, skill sheets,…

Skills for Health Care Assistants Vol. II. Supplemental Units for Health Care and Nurse Assistants Programs. Student Guide. Instructor Key. Revised.

ERIC Educational Resources Information Center

Missouri Univ., Columbia. Instructional Materials Lab.

This student guide for courses for health care assistants and nurse assistants contains 16 self-paced units with simplified line drawings, controlled text, vocabulary development, and mathematics practice exercises. Units consist of the following: objectives, introduction to the unit, content outline, steps of the procedure, skill sheets, written…

A Particle Swarm Optimization Approach to Composing Serial Test Sheets for Multiple Assessment Criteria

ERIC Educational Resources Information Center

Yin, Peng-Yeng; Chang, Kuang-Cheng; Hwang, Gwo-Jen; Hwang, Gwo-Haur; Chan, Ying

2006-01-01

To accurately analyze the problems of students in learning, the composed test sheets must meet multiple assessment criteria, such as the ratio of relevant concepts to be evaluated, the average discrimination degree, difficulty degree and estimated testing time. Furthermore, to precisely evaluate the improvement of student's learning performance…

Hazards/Failure Modes and Effects Analysis MK 1 MOD 0 LSO-HUD Console System.

DTIC Science & Technology

1980-03-24

AsI~f~ ! 127 = 3gc Z Isre -0 -q ~sI I I 𔃻~~~ ~ _ _ 3_______ II! -0udC Z Z’ P4 12 d-U * ~s ’:i~i42 S- 60 -, Uh ~ U3l I OM -C ~ . - U 4~ dcd 8U-q Ali...8 VI SCOPE AND METHODOLOGY OF ANALYSIS ........ 1O FIGURE 1: H/ FMEA /(SSA) WORK SHEET FORMAT ........... 14 APPENDIX A: HAZARD/FAILURE MODES AND...EFFECTS ANALYSIS (H/ FMEA ) -- WORK SHEETS ......... 15(A-O) TABLE: SUBSYSTEM: UNIT I Heads-Up Display Console .............. 17(A-1) UNIT 2 Auxiliary

List of Research Publications 1940-1980

DTIC Science & Technology

1981-10-01

comparison of the amount of tolerance for misplaced answers found in the GPO and the IBM machine-scored answer sheets. January 1942. (X6304) 1-18 A& .1...machine scoring of answer sheets. March 1942. The effect of the use of No. I pencils on the accuracy of scoring IBM answer sheets by machine. July 1942...X6427) 482 Hobbies - IBM code. 483 Relationship of Classification Test, R-I and WAC Classi- 4023 fication Test-2 for a recruiting station population

Synthesis: Part II, Land Use Attractiveness.

ERIC Educational Resources Information Center

Pressman, Rob

This material includes student guide sheets, reference material, and tape script for the audio-tutorial unit on the Synthesis Unit, Land Use Attractiveness. An audiotape is used with the materials. The material is designed for use with Connecticut schools, but can be adapted to other localities. The unit is designed to build on skills and…

Phthalocyanine based metal containing porous carbon sheet

NASA Astrophysics Data System (ADS)

Honda, Z.; Sakaguchi, Y.; Tashiro, M.; Hagiwara, M.; Kida, T.; Sakai, M.; Fukuda, T.; Kamata, N.

2017-03-01

Highly-ordered fused-ring poly copper phthalocyanine (PCuPc) was prepared using copper octacyanophthalocyanine as a building block, and two-dimensional (2D) square superlattices were directly observed by the transmission electron microscopy. Remarkably, we have found a formation of polymer network that consists of a 2D porous PCuPc sheet in which the centers of phthalocyanine units are alternately occupied by Cu atom and vacancy. Using this "half-filling" PCuPc, it must be possible to create alternating arrangements for transition metal centers, and therefore control the magnetic properties of the 2D carbon sheets.

Electronic properties of T graphene-like C-BN sheets: A density functional theory study

NASA Astrophysics Data System (ADS)

Majidi, R.

2015-11-01

We have used density functional theory to study the electronic properties of T graphene-like C, C-BN and BN sheets. The planar T graphene with metallic property has been considered. The results show that the presence of BN has a considerable effect on the electronic properties of T graphene. The T graphene-like C-BN and BN sheets show semiconducting properties. The energy band gap is increased by enhancing the number of BN units. The possibility of opening and controlling band gap opens the door for T graphene in switchable electronic devices.

EVALUATION OF FABRIC MEMBRANES FOR USE IN SALTSTONE DRAIN WATER SYSTEM

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pickenheim, B.; Miller, D.; Burket, P.

2012-03-08

Saltstone Disposal Unit 2 contains a sheet drain fabric intended to separate solids from drain water to be returned to the Salt Feed Tank. A similar system installed in Vault 4 appears to be ineffective in keeping solids out of the drain water return lines. Waste Solidification Engineering is considering installation of an additional fabric membrane to supplement the existing sheet drain in SDU 2. Amerdrain 200 is the product currently installed in SDU 2. This product is no longer available, so Sitedrain 94 was used as the replacement product in this testing. Fabrics with apparent opening sizes of 10,more » 25, 50 and 100 microns were evaluated. These fabrics were evaluated under three separate test conditions, a water flow test, a solids retention test and a grout pour test. A flow test with water showed that installation of an additional filter layer will predictably reduce the theoretical flux through the sheet drain. The manufacturer reports the flux for Sitedrain 94 as 150 gpm/ft{sup 2} by ASTM D-4491. This compares reasonably well with the 117 gpm/ft{sup 2} obtained in this testing. A combination of the 10 micron fabric with Sitedrain 94 could be expected to decrease flux by about 10 times as compared to Sitedrain 94 alone. The different media were used to filter a slag and fly ash mixture from water. Slag historically has the smallest nominal particle size of the premix components. Cement was omitted from the test because of its reactivity with water would prohibit accurately particle size measurements of the filtered samples. All four media sizes were able to remove greater than 95% of particles larger than 100 microns from the slurry. The smaller opening sizes were increasingly effective in removing more particles. The 10 micron filter captured 15% of the total amount of solids used in the test. This result implies that some insoluble particles may still be able to enter the drain water collection system, although the overall solids rejection is significantly improved over the current design. Test boxes were filled with grout to evaluate the performance of the sheet drain and fabrics in a simulated vault environment. All of the tests produced a similar amount of drain water, between 8-11% of the amount of water in the mix, which is expected with the targeted formulation. All of the collected drain waters contained some amount of solids, although the 10 micron filter did not appear to allow any premix materials to pass through. The solids collected from this box are believed to consist of calcium carbonate based on one ICP-AES measurement. Any of the four candidate fabrics would be an improvement over the sheet drain alone relative to solids removal. The 10 micron fabric is the only candidate that stopped all premix material from passing. The 10 micron fabric will also cause the largest decrease in flux. This decrease in flux was not enough to inhibit the total amount of drain water removed, but may lead to increased time to remove standing water prior to subsequent pours in the facility. The acceptability of reduced liquid flux through the 10 micron fabric will depend on the amount of excess water to be removed, the time available for water removal and the total area of fabric installed at the disposal cell.« less

Sensitivity of simulated englacial isochrones to uncertain subglacial boundary conditions in central West Antarctica: Implications for detecting changes in ice dynamics

NASA Astrophysics Data System (ADS)

Muldoon, Gail; Jackson, Charles S.; Young, Duncan A.; Quartini, Enrica; Cavitte, Marie G. P.; Blankenship, Donald D.

2017-04-01

Information about the extent and dynamics of the West Antarctic Ice Sheet during past glaciations is preserved inside ice sheets themselves. Ice cores are capable of retrieving information about glacial history, but they are spatially sparse. Ice-penetrating radar, on the other hand, has been used to map large areas of the West Antarctic Ice Sheet and can be correlated to ice core chronologies. Englacial isochronous layers observed in ice-penetrating radar are the result of variations in ice composition, fabric, temperature and other factors. The shape of these isochronous surfaces is expected to encode information about past and present boundary conditions and ice dynamics. Dipping of englacial layers, for example, may reveal the presence of rapid ice flow through paleo ice streams or high geothermal heat flux. These layers therefore present a useful testbed for hypotheses about paleo ice sheet conditions. However, hypothesis testing requires careful consideration of the sensitivity of layer shape to the competing forces of ice sheet boundary conditions and ice dynamics over time. Controlled sensitivity tests are best completed using models, however ice sheet models generally do not have the capability of simulating layers in the presence of realistic boundary conditions. As such, modeling 3D englacial layers for comparison to observations is difficult and requires determination of a 3D ice velocity field. We present a method of post-processing simulated 3D ice sheet velocities into englacial isochronous layers using an advection scheme. We then test the sensitivity of layer geometry to uncertain boundary conditions, including heterogeneous subglacial geothermal flux and bedrock topography. By identifying areas of the ice sheet strongly influenced by boundary conditions, it may be possible to isolate the signature of paleo ice dynamics in the West Antarctic ice sheet.

Electrical Subsystems Flight Test Handbook

DTIC Science & Technology

1984-01-01

distribution of this handbook to the public at large, or by DDC to the National Technical Information Service (NTIS). At NTIS, it will be available to...Abnormal Mode 58 Emergency Mode 61 Instrumentation 62 Test Information Sheets 62 Integration with Flight Test Program 62 DATA MEASUREMENT, ANALYS IS...AND EVALUATION 65 REFERENCES 73 -APPENDIX A - EXAMPLE OF TEST INFORMATION SHEET 75 APPENDIX B - EXAMPLE OF TEST PLAN SAFETY REVIEW 85 APPENDIX C

Controlling microstructure and texture in magnesium alloy sheet by shear-based deformation processing

NASA Astrophysics Data System (ADS)

Sagapuram, Dinakar

Application of lightweight Mg sheet is limited by its low workability, both in production of sheet (typically by multistep hot and cold-rolling) and forming of sheet into components. Large strain extrusion machining (LSEM), a constrained chip formation process, is used to create Mg alloy AZ31B sheet in a single deformation step. The deformation in LSEM is shown to be intense simple shear that is confined to a narrow zone, which results in significant deformation-induced heating up to ~ 200°C and reduces the need for pre-heating to realize continuous sheet forms. This study focuses on the texture and microstructure development in the sheet processed by LSEM. Interestingly, deep, highly twinned steady-state layer develops in the workpiece subsurface due to the compressive field ahead of the shear zone. The shear deformation, in conjunction with this pre-deformed twinned layer, results in tilted-basal textures in the sheet with basal planes tilted well away from the surface. These textures are significantly different from those in rolled sheet, where basal planes are nearly parallel to the surface. By controlling the strain path, the basal plane inclination from the surface could be varied in the range of 32-53°. B-fiber (basal plane parallel to LSEM shear plane), associated with basal slip, is the major texture component in the sheet. An additional minor C2-fiber component appears above 250°C due to the thermal activation of pyramidal slip. Together with these textures, microstructure ranges from severely cold-worked to (dynamically) recrystallized type, with the corresponding grain sizes varying from ultrafine- (~ 200 nm) to fine- (2 mum) grained. Small-scale limiting dome height (LDH) confirmed enhanced formability (~ 50% increase in LDH) of LSEM sheet over the conventional rolled sheet. Premature, twinning-driven shear fractures are observed in the rolled sheet with the basal texture. In contrast, LSEM sheet with a tilted-basal texture favorably oriented for basal slip exhibits ductile tensile-type fracture. A two-fold increase in ductility is also observed for the LSEM sheet under uniaxial tensile testing without significant changes in the strength. Among texture and microstructure (grain size), texture is shown to be more critical for Mg sheet formability. However, in conjunction with a favorable texture, fine recrystallized microstructure provides for additional enhancement of strain-hardening capacity and formability. In-situ imaging of material flow during uniaxial tensile testing revealed new, interesting flow localization phenomena and fracture behavior. It is shown that the deformation behavior of Mg sheet is highly texture dependent, and also radically different from that of conventional ductile metals both in terms of necking and fracture. The implications of these observations for the LDH test results and formability of Mg sheet, in general, are briefly discussed.

Arsenic in Ground Water of the United States

MedlinePlus

... a hard problem : Geotimes Newsmagazine of the Earth Sciences, v.46 no.11, p.34-36. (2001) DATA Arsenic in ground-water resources of the United States : U.S. Geological Survey Fact Sheet 063-00. (2000) A retrospective analysis on ...

Residential Carpentry.

ERIC Educational Resources Information Center

Hendrix, Laborn J.

This curriculum guide provides instructional materials for a course to train carpenters who will make careers in construction. It includes 6 sections and 21 instructional units. Each unit of instruction consists of eight basic components: performance objectives, teacher activities, information sheets (content essential for meeting the cognitive…

Nairobi Forward-looking Strategies for the Advancement of Women: Issues and the Canadian Situation. Fact Sheets--1992 Update.

ERIC Educational Resources Information Center

Status of Women Canada, Ottawa (Ontario).

The 1992 edition of the fact sheets provides information on new and revised Canadian government programs and policies about the implementation of the Nairobi Forward-looking Strategies for the Advancement of Women program that were adopted at the United Nations World Conference on Women in Kenya in 1985. This edition continues to address the…

Fuels planning: science synthesis and integration; environmental consequences fact sheet 13: Root Disease Analyzer-Armillaria Response Tool (ART)

Treesearch

Geral I. McDonald; Philip D. Tanimoto; Thomas M. Rice; David E. Hall; Jane E. Stewart; Paul J. Zambino; Jonalea R. Tonn; Ned B. Klopfenstein; Mee-Sook Kim

2005-01-01

The Root Disease Analyzer-Armillaria Response Tool (ART) is a Web-based tool that estimates Armillaria root disease risk in dry forests of the Western United States. This fact sheet identifies the intended users and uses, required inputs, what the model does and does not do, and tells the user how to obtain the model.

Clinical Social Work. State Laws Governing Independent Practice and Reimbursement of Services. Fact Sheet for the Honorable Daniel K. Inouye, United States Senate.

ERIC Educational Resources Information Center

General Accounting Office, Washington, DC. Div. of Human Resources.

This fact sheet on state laws governing the independent practice and reimbursement of services for clinical social workers contains information from questionnaires sent to the state agencies responsible for health insurance regulations and Medicaid and licensing activities. Information on Ohio, the only state which did not respond, is not…

Building clinical data groups for electronic medical record in China.

PubMed

Tu, Haibo; Yu, Yingtao; Yang, Peng; Tang, Xuejun; Hu, Jianping; Rao, Keqin; Pan, Feng; Xu, Yongyong; Liu, Danhong

2012-04-01

This article aims at building clinical data groups for Electronic Medical Records (EMR) in China. These data groups can be reused as basic information units in building the medical sheets of Electronic Medical Record Systems (EMRS) and serve as part of its implementation guideline. The results were based on medical sheets, the forms that are used in hospitals, which were collected from hospitals. To categorize the information in these sheets into data groups, we adopted the Health Level 7 Clinical Document Architecture Release 2 Model (HL7 CDA R2 Model). The regulations and legal documents concerning health informatics and related standards in China were implemented. A set of 75 data groups with 452 data elements was created. These data elements were atomic items that comprised the data groups. Medical sheet items contained clinical records information and could be described by standard data elements that exist in current health document protocols. These data groups match different units of the CDA model. Twelve data groups with 87 standardized data elements described EMR headers, and 63 data groups with 405 standardized data elements constituted the body. The later 63 data groups in fact formed the sections of the model. The data groups had two levels. Those at the first level contained both the second level data groups and the standardized data elements. The data groups were basically reusable information units that served as guidelines for building EMRS and that were used to rebuild a medical sheet and serve as templates for the clinical records. As a pilot study of health information standards in China, the development of EMR data groups combined international standards with Chinese national regulations and standards, and this was the most critical part of the research. The original medical sheets from hospitals contain first hand medical information, and some of their items reveal the data types characteristic of the Chinese socialist national health system. It is possible and critical to localize and stabilize the adopted international health standards through abstracting and categorizing those items for future sharing and for the implementation of EMRS in China.

Vibration characteristics of walls and a plate glass window representative of those of a wood-frame house

NASA Technical Reports Server (NTRS)

Carden, H. D.

1979-01-01

Mechanical excitation was used, and measurements of acceleration response, natural frequencies, and nodal patterns were performed. Results indicate that the wall sections and the complete wall did not act as a unit in responding to sinusoidal vibration inputs. Calculated frequencies of the components that account for this independent behavior of the studs and face sheets agreed resonably well with experimental frequencies. Experimental vibrations of the plate glass window agreed with the calculated behavior, and responses of the window exposed to airplane flyover noise were readily correlated with the test results.

Photoinduced Reversible Morphological Transformation of Azobenzene-Containing Pseudo-2D Polymers.

PubMed

Li, Zili; Tang, Miao; Jiang, Chen; Bai, Ruke; Bai, Wei

2018-05-02

2D polymer sheets containing azobenzene are successfully prepared by a facile strategy of "2D self-assembly polymerization (2DSP)" via free radical polymerization in solution. A bola amphiphile containing azobenzene as a novel monomer is designed and synthesized. The results indicate that single-layer covalent pseudo-2D polymers on a micrometer scale are obtained after polymerization with vinyl monomers. Moreover, the 2D polymer sheets are highly sensitive to UV light due to incorporation of azobenzene groups into the polymer. Upon alternative irradiation with UV and visible light, the morphological transformation between sheets and rolled-up nanotubes can be achieved based on the reversible trans-to-cis photoisomerization of azobenzene units in the 2D polymer sheets. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Disulfide-Mediated β-Strand Dimers: Hyperstable β-Sheets Lacking Tertiary Interactions and Turns.

PubMed

Kier, Brandon L; Anderson, Jordan M; Andersen, Niels H

2015-04-29

Disulfide bonds between cysteine residues are essential to the structure and folding of many proteins. Yet their role in the design of structured peptides and proteins has frequently been limited to use as intrachain covalent staples that reinforce existing structure or induce knot-like conformations. In β-hairpins, their placement at non-H-bonding positions across antiparallel strands has proven useful for achieving fully folded positive controls. Here we report a new class of designed β-sheet peptide dimers with strand-central disulfides as a key element. We have found that the mere presence of a disulfide bond near the middle of a short peptide chain is sufficient to nucleate some antiparallel β-sheet structure; addition of β-capping units and other favorable cross-strand interactions yield hyperstable sheets. Strand-central cystines were found to be superior to the best designed reversing turns in terms of nucleating β-sheet structure formation. We have explored the limitations and possibilities of this technique (the use of disulfides as sheet nucleators), and we provide a set of rules and rationales for the application and further design of disulfide-tethered "turnless" β-sheets.

Rotator cuff repair using cell sheets derived from human rotator cuff in a rat model.

PubMed

Harada, Yoshifumi; Mifune, Yutaka; Inui, Atsuyuki; Sakata, Ryosuke; Muto, Tomoyuki; Takase, Fumiaki; Ueda, Yasuhiro; Kataoka, Takeshi; Kokubu, Takeshi; Kuroda, Ryosuke; Kurosaka, Masahiro

2017-02-01

To achieve biological regeneration of tendon-bone junctions, cell sheets of human rotator-cuff derived cells were used in a rat rotator cuff injury model. Human rotator-cuff derived cells were isolated, and cell sheets were made using temperature-responsive culture plates. Infraspinatus tendons in immunodeficient rats were resected bilaterally at the enthesis. In right shoulders, infraspinatus tendons were repaired by the transosseous method and covered with the cell sheet (sheet group), whereas the left infraspinatus tendons were repaired in the same way without the cell sheet (control group). Histological examinations (safranin-O and fast green staining, isolectin B4, type II collagen, and human-specific CD31) and mRNA expression (vascular endothelial growth factor; VEGF, type II collagen; Col2, and tenomodulin; TeM) were analyzed 4 weeks after surgery. Biomechanical tests were performed at 8 weeks. In the sheet group, proteoglycan at the enthesis with more type II collagen and isolectin B4 positive cells were seen compared with in the control group. Human specific CD31-positive cells were detected only in the sheet group. VEGF and Col2 gene expressions were higher and TeM gene expression was lower in the sheet group than in the control group. In mechanical testing, the sheet group showed a significantly higher ultimate failure load than the control group at 8 weeks. Our results indicated that the rotator-cuff derived cell sheet could promote cartilage regeneration and angiogenesis at the enthesis, with superior mechanical strength compared with the control. Treatment for rotator cuff injury using cell sheets could be a promising strategy for enthesis of tendon tissue engineering. © 2016 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 35:289-296, 2017. © 2016 Orthopaedic Research Society. Published by Wiley Periodicals, Inc.

Experimental and Numerical Study on the Deformation Mechanism in AZ31B Mg Alloy Sheets Under Pulsed Electric-Assisted Tensile and Compressive Tests

NASA Astrophysics Data System (ADS)

Lee, Jinwoo; Kim, Se-Jong; Lee, Myoung-Gyu; Song, Jung Han; Choi, Seogou; Han, Heung Nam; Kim, Daeyong

2016-06-01

The uniaxial tensile and compressive stress-strain responses of AZ31B magnesium alloy sheet under pulsed electric current are reported. Tension and compression tests with pulsed electric current showed that flow stresses dropped instantaneously when the electric pulses were applied. Thermo-mechanical-electrical finite element analyses were also performed to investigate the effects of Joule heating and electro-plasticity on the flow responses of AZ31B sheets under electric-pulsed tension and compression tests. The proposed finite element simulations could reproduce the measured uniaxial tensile and compressive stress-strain curves under pulsed electric currents, when the temperature-dependent flow stress hardening model and thermal properties of AZ31B sheet were properly described in the simulations. In particular, the simulation results that fit best with experimental results showed that almost 100 pct of the electric current was subject to transform into Joule heating during electrically assisted tensile and compressive tests.

South Carolina Guide for Selling.

ERIC Educational Resources Information Center

Elliott, Ronald T.

This curriculum guide provides materials for a secondary course in salesmanship. It contains 6 units that cover 33 competencies. Each competency is presented in a standard format: performance objective, resources, teaching activities, evaluation, and supplementary materials, including an information sheet, exercises, and checklists. Units and…

Free-Space Measurements of Dielectrics and Three-Dimensional Periodic Metamaterials

NASA Astrophysics Data System (ADS)

Kintner, Clifford E.

This thesis presents the free-space measurements of a periodic metamaterial structure. The metamaterial unit cell consists of two dielectric sheets intersecting at 90 degrees. The dielectric is a polyetherimide-based material 0.001" thick. Each sheet has a copper capacitively-loaded loop (CLL) structure on the front and a cut-wire structure on the back. Foam material is used to support the unit cells. The unit cell repeats 40 times in the x-direction, 58 times in the y-direction and 5 times in the z-direction. The sample measures 12" x 12" x 1" in total. We use a free-space broadband system comprised of a pair of dielectric-lens horn antennas with bandwidth from 5.8 GHz to 110 GHz, which are connected to a HP PNA series network analyzer. The dielectric lenses focus the incident beam to a footprint measuring 1 wavelength by 1 wavelength. The sample holder is positioned at the focal point between the two antennas. In this work, the coefficients of transmission and reflection (the S-parameters S21 and S11) are measured at frequencies from 12.4 GHz up to 30 GHz. Simulations are used to validate the measurements, using the Ansys HFSS commercial software package on the Arkansas High Performance Computing Center cluster. The simulation results successfully validate the S-parameters measurements, in particular the amplitudes. An algorithm based on the Nicolson-Ross-Weir (NRW) method is implemented to extract the permittivity and permeability values of the metamaterial under test. The results show epsilon-negative, mu-negative and double-negative parameters within the measured frequency range.

Nurse Assistant in Acute, Home Health and Long-Term Care Settings. Instructor Manual [and] Student Manual.

ERIC Educational Resources Information Center

Winberg, Pat

This document consists of an instructor's manual and student manual for a nurse assistant curriculum. The instructor's manual provides answers to activity sheets and unit evaluations along with individual unit overviews. Suggested teaching strategies and audiovisual supplements are included for each lesson. The student manual contains eight units:…

GATE HOUSE FOR UNITED ENGINEERING CO., Alameda, California. Four elevations ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

GATE HOUSE FOR UNITED ENGINEERING CO., Alameda, California. Four elevations and three sections. Alben Froberg, Architect, Oakland, California. Sheet no. 1. Scale 1/4 inch to the foot, elevations. Scale ~ inch to the foot, sections. July 31, 1941. pencil on tracing paper - United Engineering Company Shipyard, Gate House, 2900 Main Street, Alameda, Alameda County, CA

40 CFR 60.52Da - Recordkeeping requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

... (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Standards of Performance for Electric Utility... opacity field data sheets; (2) For each performance test conducted using Method 22 of appendix A-4 of this... performance test; (iii) Copies of all visible emission observer opacity field data sheets; and (iv...

Full Stokes finite-element modeling of ice sheets using a graphics processing unit

NASA Astrophysics Data System (ADS)

Seddik, H.; Greve, R.

2016-12-01

Thermo-mechanical simulation of ice sheets is an important approach to understand and predict their evolution in a changing climate. For that purpose, higher order (e.g., ISSM, BISICLES) and full Stokes (e.g., Elmer/Ice, http://elmerice.elmerfem.org) models are increasingly used to more accurately model the flow of entire ice sheets. In parallel to this development, the rapidly improving performance and capabilities of Graphics Processing Units (GPUs) allows to efficiently offload more calculations of complex and computationally demanding problems on those devices. Thus, in order to continue the trend of using full Stokes models with greater resolutions, using GPUs should be considered for the implementation of ice sheet models. We developed the GPU-accelerated ice-sheet model Sainō. Sainō is an Elmer (http://www.csc.fi/english/pages/elmer) derivative implemented in Objective-C which solves the full Stokes equations with the finite element method. It uses the standard OpenCL language (http://www.khronos.org/opencl/) to offload the assembly of the finite element matrix on the GPU. A mesh-coloring scheme is used so that elements with the same color (non-sharing nodes) are assembled in parallel on the GPU without the need for synchronization primitives. The current implementation shows that, for the ISMIP-HOM experiment A, during the matrix assembly in double precision with 8000, 87,500 and 252,000 brick elements, Sainō is respectively 2x, 10x and 14x faster than Elmer/Ice (when both models are run on a single processing unit). In single precision, Sainō is even 3x, 20x and 25x faster than Elmer/Ice. A detailed description of the comparative results between Sainō and Elmer/Ice will be presented, and further perspectives in optimization and the limitations of the current implementation.

Real-time testing of titanium sheet and extrusion coupon specimens subjected to Mach 2.7 supersonic cruise aircraft wing stresses and temperatures

NASA Technical Reports Server (NTRS)

Lunde, T.

1977-01-01

The accuracy of three accelerated flight-by-flight test methods for material selection, and fatigue substantiation of supersonic cruise aircraft structure was studied. The real time stresses and temperatures applied to the specimens were representative of the service conditions in the lower surface of a Mach 2.7 supersonic cruise aircraft wing root structure. Each real time flight lasted about 65 minutes, including about one hour at (500 F) in the cruise condition. Center notched coupon specimens from six titanium materials were tested: mill-annealed, duplex-annealed, and triplex-annealed Ti-8Al-1Mo-1V sheets; mill-annealed Ti-8Al-1Mo-1V extrusion; mill-annealed Ti-6Al-4V sheet; and solution-treated and aged Ti-6Al-4V extrusion. For duplex-annealed Ti-8Al-1Mo-1V sheet, specimens with single spotweld were also tested. The test results were studied in conjunction with other related data from the literature for: material selection, structural fabrication, fatigue resistance of supersonic cruise aircraft structure, and fatigue test acceleration procedures for supersonic cruise aircraft.

Peeling behavior and spalling resistance of CFRP sheets bonded to bent concrete surfaces

NASA Astrophysics Data System (ADS)

Yuan, Hong; Li, Faping

2010-05-01

In this paper, the peeling behavior and the spalling resistance effect of carbon fiber reinforced polymer (CFRP) sheets externally bonded to bent concrete surfaces are firstly investigated experimentally. Twenty one curved specimens and seven plane specimens are studied in the paper, in which curved specimens with bonded CFRP sheets can simulate the concrete spalling in tunnel, culvert, arch bridge etc., whereas plane specimens with bonded CFRP sheets can simulate the concrete spalling in beam bridge, slab bridge and pedestrian bridge. Three kinds of curved specimens with different radii of curvature are chosen by referring to practical tunnel structures, and plane specimens are used for comparison with curved ones. A peeling load is applied on the FRP sheet by loading a circular steel tube placed into the central notch of beam to debond CFRP sheets from the bent concrete surface, meanwhile full-range load-deflection curves are recorded by a MTS 831.10 Elastomer Test System. Based on the experimental results, a theoretical analysis is also conducted for the specimens. Both theoretical and experimental results show that only two material parameters, the interfacial fracture energy of CFRP-concrete interface and the tensile stiffness of CFRP sheets, are needed for describing the interfacial spalling behavior. It is found that the radius of curvature has remarkable influence on peeling load-deflection curves. The test methods and test results given in the paper are helpful and available for reference to the designer of tunnel strengthening.

Mega debris flow deposits on the western Wilkes Land margin, East Antarctica

USGS Publications Warehouse

Donda, F.; O'Brien, P.E.; De Santis, L.; Rebesco, M.; Brancolini, Giuliano

2007-01-01

Multichannel seismic data collected off Western Wilkes Land (East Antarctica) reveal the occurrence of mega debris flow deposits on the lower slope and rise that were formed throughout the Miocene. Commonly, debris flow units are separated by thin deposits of well-stratified facies, interpreted as predominantly glaciomarine mixed contouritic and distal turbidite deposits. These units could act as weak layers and could have played a major role in the slope instability. High sedimentation rates, due to large amounts of sediment delivered from a temperate, wet-based ice sheet, constituted a key factor in the sediment failures. The main trigger mechanism would probably have been earthquakes enhanced by isostatic rebound following major ice sheet retreats.

Construction of Experimental Roofing.

DTIC Science & Technology

1981-11-01

buildings at Fort Benning, GA; Fort Knox, KY; and Fort Lewis, WA. Sheets of EPDM synthetic rubber were installed on buildings at Forts Benning and Lewis...Contract and Unit Costs 14 5 Polyurethane Foam Roofing -- Initial Physical Properties 28 6 EPDM Sheet Rubber Roofing -- Initial Physical Properties 30 7...the new system. The system selected for Area A was an EPDM synthetic rubber manufactured by Carlisle Tire and Rubber Company. The contract specified

World Population and Beyond: A Teaching Strategy for Global Studies [And] Interchange. Population Education Newsletter. Vol. 7, No. 2, May 1978 [And] 1977 World Population Data Sheet.

ERIC Educational Resources Information Center

Clark, Leon E.; And Others

The unit contains a teacher's guide, student reading materials, and data sheets about a variety of worldwide demographic and economic variables. Designed for students in junior high through college, its goals are to encourage students to analyze the causes and consequences of world population and economic trends, and to detect interrelationships…

Fuels planning: science synthesis and integration; environmental consequences fact sheet 03: structure fires in the wildland-urban interface

Treesearch

Steve Sutherland

2004-01-01

National Fire Protection Association (NFPA) data indicate that wildfires destroyed approximately 9,000 homes between 1985 and 1994 in the United States. The loss of homes to wildfire has had a significant impact on Federal fire policy. This fact sheet discusses the causes of home ignitions in the wildland-urban interface, home ignition zones, how to reduce home...

Closure Report (CR) for Corrective Action Unit (CAU) 91: Area 3 U-3fi Injection Well with Errata Sheet and Certification, Revision 0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Navarro Nevada Environmental Services

The closure report for CAU 91 has no Use Restriction Form or drawing/map included in the document to describe the use restricted area, however, Section 3.3.3 states that the site will be fenced and signage placed indicating the area as a Resource Conservation and Recovery Act (RCRA) Unit. The drawing that was placed in the FFACO indicating the use restricted area lists the coordinates for the RCRA Unit in Nevada State Plan Coordinates - North American Datum of 1983. In the ensuing years the reporting of coordinates has been standardized so that all coordinates are reported in the same manner,more » which is: NAD 27 UTM Zone 11 N, meters. This Errata Sheet updates the coordinate reporting to the currently accepted method and includes an aerial photo showing the RCRA Unit with the coordinates listed showing the use restricted area.« less

Distinct C9orf72-Associated Dipeptide Repeat Structures Correlate with Neuronal Toxicity

PubMed Central

Krans, Amy; Sawaya, Michael R.; Paulson, Henry L.; Todd, Peter K.; Barmada, Sami J.; Ivanova, Magdalena I.

2016-01-01

Hexanucleotide repeat expansions in C9orf72 are the most common inherited cause of amyotrophic lateral sclerosis (ALS) and frontotemporal dementia (FTD). The expansions elicit toxicity in part through repeat-associated non-AUG (RAN) translation of the intronic (GGGGCC)n sequence into dipeptide repeat-containing proteins (DPRs). Little is known, however, about the structural characteristics and aggregation propensities of the dipeptide units comprising DPRs. To address this question, we synthesized dipeptide units corresponding to the three sense-strand RAN translation products, analyzed their structures by circular dichroism, electron microscopy and dye binding assays, and assessed their relative toxicity when applied to primary cortical neurons. Short, glycine-arginine (GR)3 dipeptides formed spherical aggregates and selectively reduced neuronal survival compared to glycine-alanine (GA)3 and glycine-proline (GP)3 dipeptides. Doubling peptide length had little effect on the structure of GR or GP peptides, but (GA)6 peptides formed β-sheet rich aggregates that bound thioflavin T and Congo red yet lacked the typical fibrillar morphology of amyloids. Aging of (GA)6 dipeptides increased their β-sheet content and enhanced their toxicity when applied to neurons. We also observed that the relative toxicity of each tested dipeptide was proportional to peptide internalization. Our results demonstrate that different C9orf72-related dipeptides exhibit distinct structural properties that correlate with their relative toxicity. PMID:27776165

Analysis of fracture in sheet bending and roll forming

NASA Astrophysics Data System (ADS)

Deole, Aditya D.; Barnett, Matthew; Weiss, Matthias

2018-05-01

The bending limit or minimum bending radius of sheet metal is conventionally measured in a wiping (swing arm) or in a vee bend test and reported as the minimum radius of the tool over which the sheet can be bent without fracture. Frequently the material kinks while bending so that the actual inner bend radius of the sheet metal is smaller than the tool radius giving rise to inaccuracy in these methods. It has been shown in the previous studies that conventional bend test methods may under-estimate formability in bending dominated processes such as roll forming. A new test procedure is proposed here to improve understanding and measurement of fracture in bending and roll forming. In this study, conventional wiping test and vee bend test have been performed on martensitic steel to determine the minimum bend radius. In addition, the vee bend test is performed in an Erichsen sheet metal tester equipped with the GOM Aramis system to enable strain measurement on the outer surface during bending. The strain measurement before the onset of fracture is then used to determine the minimum bend radius. To compare this result with a technological process, a vee channel is roll formed and in-situ strain measurement carried out with the Vialux Autogrid system. The strain distribution at fracture in the roll forming process is compared with that predicted by the conventional bending tests and by the improved process. It is shown that for this forming operation and material, the improved procedure gives a more accurate prediction of fracture.

75 FR 43995 - Agency Information Collection Activities: Submission for OMB Review; Comment Request, OMB No...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-07-27

... DEPARTMENT OF HOMELAND SECURITY Federal Emergency Management Agency [Docket ID: FEMA-2010-0026...; FEMA/EMI Independent Study Course Enrollment and Test Answer Sheet AGENCY: Federal Emergency Management... Course Enrollment and Test Answer Sheet (paper and electronic). SUMMARY: The Federal Emergency Management...

Influence of Accumulative Roll Bonding on the Texture and Tensile Properties of an AZ31 Magnesium Alloy Sheets

PubMed Central

Džugan, Ján; Németh, Gergely; Lukáč, Pavel; Bohlen, Jan

2018-01-01

Deformation behaviour of rolled AZ31 sheets that were subjected to the accumulative roll bonding was investigated. Substantially refined microstructure of samples was achieved after the first and second pass through the rolling mill. Sheets texture was investigated using an X-ray diffractometer. Samples for tensile tests were cut either parallel or perpendicular to the rolling direction. Tensile tests were performed at temperatures ranging from room temperature up to 300 °C. Tensile plastic anisotropy, different from the anisotropy observed in AZ31 sheets by other authors, was observed. This anisotropy decreases with an increasing number of rolling passes and increasing deformation temperature. Grain refinement and texture are the crucial factors influencing the deformation behaviour. PMID:29303975

Craterlike structures on the laser cut surface

NASA Astrophysics Data System (ADS)

Shulyatyev, V. B.; Orishich, A. M.

2017-10-01

Analysis of the laser cut surface morphology remain topical. It is related with the fact that the surface roughness is the main index of the cut quality. The present paper deals with the experimental study of the relatively unstudied type of defects on the laser cut surface, dimples, or craters. According to the measurement results, amount of craters per unit of the laser cut surface area rises as the sheet thickness rises. The crater diameter rises together with the sheet thickness and distance from the upper sheet edge. The obtained data permit concluding that the defects like craters are observed predominantly in the case of thick sheets. The results agree with the hypothesis of crater formation as impact structures resulting from the melt drops getting on the cut channel walls upon separation from the cut front by the gas flow.

NEUTRON SHIELDING STRUCTURE

DOEpatents

Mattingly, J.T.

1962-09-25

A lightweight neutron shielding structure comprises a honeycomb core which is filled with a neutron absorbing powder. The honeycomb core is faced with parallel planar facing sheets to form a lightweight rigid unit. Suitable absorber powders are selected from among the following: B, B/sub 4/C, B/sub 2/O/ sub 3/, CaB/sub 6/, Li/sub 2/CO3, LiOH, LiBO/sub 2/, Li/s ub 2/O. The facing sheets are constructed of a neutron moderating material, so that fast neutrons will be moderated while traversing the facing sheets, and ultimately be absorbed by the absorber powder in the honeycomb. Beryllium is a preferred moderator material for use in the facing sheets. The advantage of the structure is that it combines the rigidity and light weight of a honeycomb construction with the neutron absorption properties of boron and lithium. (AEC)

Geologic map of the Cucamonga Peak 7.5' quadrangle, San Bernardino County, California

USGS Publications Warehouse

Morton, D.M.; Matti, J.C.; Digital preparation by Koukladas, Catherine; Cossette, P.M.

2001-01-01

a. This Readme; includes in Appendix I, data contained in fif_met.txt b. The same graphic as plotted in 2 above. (Test plots have not produced 1:24,000-scale map sheets. Adobe Acrobat pagesize setting influences map scale.) The Correlation of Map Units and Description of Map Units is in the editorial format of USGS Miscellaneous Investigations Series (I-series) maps but has not been edited to comply with I-map standards. Within the geologic map data package, map units are identified by standard geologic map criteria such as formation-name, age, and lithology. Even though this is an author-prepared report, every attempt has been made to closely adhere to the stratigraphic nomenclature of the U. S. Geological Survey. Descriptions of units can be obtained by viewing or plotting the .pdf file (3b above) or plotting the postscript file (2 above). If roads in some areas, especially forest roads that parallel topographic contours, do not show well on plots of the geologic map, we recommend use of the USGS Cucamonga Peak 7.5’ topographic quadrangle in conjunction with the geologic map.

Geologic map of the Telegraph Peak 7.5' quadrangle, San Bernardino County, California

USGS Publications Warehouse

Morton, D.M.; Woodburne, M.O.; Foster, J.H.; Morton, Gregory; Cossette, P.M.

2001-01-01

a. This Readme; includes in Appendix I, data contained in fif_met.txt b. The same graphic as plotted in 2 above. Test plots have not produced 1:24,000-scale map sheets. Adobe Acrobat pagesize setting influences map scale. The Correlation of Map Units and Description of Map Units is in the editorial format of USGS Miscellaneous Investigations Series (I-series) maps but has not been edited to comply with I-map standards. Within the geologic map data package, map units are identified by standard geologic map criteria such as formation-name, age, and lithology. Even though this is an author-prepared report, every attempt has been made to closely adhere to the stratigraphic nomenclature of the U. S. Geological Survey. Descriptions of units can be obtained by viewing or plotting the .pdf file (3b above) or plotting the postscript file (2 above). If roads in some areas, especially forest roads that parallel topographic contours, do not show well on plots of the geologic map, we recommend use of the USGS Telegraph Peak 7.5’ topographic quadrangle in conjunction with the geologic map.

Lightweight long life heat exchanger

NASA Technical Reports Server (NTRS)

Moore, E. K.

1975-01-01

The design, fabrication, and evaluation of a full scale shuttle-type condensing heat exchanger constructed of aluminum and utilizing aluminum clad titanium parting sheets is described. A long term salt spray test of candidate parting sheet specimens is described. The results of an investigation into an alternate method of making composite sheet material are discussed.

Transitions in Lava Emplacement Recorded in the Deccan Traps Sequence (India)

NASA Astrophysics Data System (ADS)

Vanderkluysen, L.; Self, S.; Jay, A. E.; Sheth, H. C.; Clarke, A. B.

2015-12-01

Transitions in the style of lava flow emplacement are recognized in the stratigraphic sequence of several mafic large igneous provinces (LIPs), including the Etendeka (Namibia), the Faeroe Islands (North Atlantic LIP), the Ethiopian Traps, and the Deccan Traps (India). These transitions, from units dominated by meter-sized pāhoehoe toes and lobes to those dominated by inflated sheet lobes tens to hundreds of meters in width and meters to tens of meters in height, seems to be a fundamental feature of LIP emplacement. In the Deccan, this volcanological transition is thought to coincide with deeper changes to the volcano-magmatic system expressed, notably, in the trace element and isotopic signature of erupted flows. We investigated this transition in the Deccan Traps by logging eight sequences along the Western Ghats, an escarpment in western India where the Deccan province is thickest and best exposed. The Deccan province, which once covered ~1 million km2 of west-central India, is subdivided in eleven chemo-stratigraphic formations in the type sections of the Western Ghats. Where the lower Deccan formations are exposed, we found that as much as 65% of the exposed thickness (below the Khandala Formation) is made up of sheet lobes, from 40% in the Bhimashankar Formation to 75% in the Thakurvadi Formation. Near the bottom of the sequence, 25% of the Neral Formation is composed of sheet lobes ≥15 m in thickness. On this basis, the traditional view that inflated sheet lobes are an exclusive feature of the upper part of the stratigraphy must be challenged. Several mechanisms have been proposed to explain the development of compound flows and inflated sheet lobes, involving one or more of the following factors: underlying slope, varying effusion rate, and source geometry. Analogue experiments are currently under way to test the relative influence of each of these factors in the development of different lava flow morphologies in LIPs.

Student Material for Competency-Based Education Curriculum for Licensed Practical Nurse.

ERIC Educational Resources Information Center

Associated Educational Consultants, Inc., Pittsburgh, PA.

This curriculum for licensed practical nurse contains 18 units. Each unit is divided into modules comprised of task or job-related competencies. A student competency sheet (SCS) provided for each task is organized into this format: unit number and name, module letter and name of the group of related tasks, and number and name of task; performance…

No Place to Call Home: Child & Youth Homelessness in the United States. Poverty Fact Sheet

ERIC Educational Resources Information Center

Damron, Neil

2015-01-01

"No Place to Call Home: Child and Youth Homelessness in the United States," prepared by intern Neil Damron and released in May 2015, presents the statistics on child and youth homelessness and recent trends in Wisconsin and the United States. It explores the major challenges faced by homeless minors, and, drawing from recent research by…

Practical Nursing. Volume II. Health Occupations Education. Revised.

ERIC Educational Resources Information Center

Rogers, Helen V.; Reid-Sloan, Jamee

This curriculum guide, revised from a 1975 edition, provides teachers with up-to-date information and skill-related applications needed by practical nurses. It includes 4 sections and 24 instructional units. Each unit of instruction consists of eight basic components: performance objectives, teacher activities, information sheets, assignment…

Learn, Grow, Become. TSA Edition.

ERIC Educational Resources Information Center

Oklahoma State Dept. of Vocational and Technical Education, Stillwater. Curriculum and Instructional Materials Center.

This revised curriculum guide contains five units that are designed to help students develop an understanding of the mission of the Technology Student Association (TSA). Each unit follows a standard format that includes some or all of these basic components: performance objectives, suggested activities, handouts, information sheets, supplements,…

75 FR 75475 - Agency Information Collection Activities: Proposed Collection; Comment Request

Federal Register 2010, 2011, 2012, 2013, 2014

2010-12-03

... collection; Title of Information Collection: Psychiatric Unit Criteria Work Sheet and Supporting Regulations... section 1886(d)(1)(B) of the Social Security Act. That section excludes psychiatric hospitals... (children's hospitals), and psychiatric and rehabilitation units which are a distinct part of a hospital...

Post-Wildfire Hydrologic Hazards in the Wildland Urban Interface of Colorado and the Western United States

USGS Publications Warehouse

Stevens, M.R.; Bossong, C.R.; Rupert, M.G.; Ranalli, A.J.; Cassidy, E.W.; Druliner, A.D.

2008-01-01

Following a wildfire, such as the 2002 Missionary Ridge fire, a number of hydrologic hazards may develop that can have an important impact on water resources, businesses, homes, reservoirs, roads, and utilities in the wildland urban interface (areas where homes and commercial developments are interspersed with wildlands) in mountainous areas of the Western United States. This fact sheet describes these hazards and identifies approaches to quantify them, thus enabling land and resource managers to plan for and mitigate the effects of these hazards. The fact sheet has been produced in association with the U.S. Geological Survey (USGS) Fire Science Thrust program and the Colorado Front Range Demonstration Project (CFRDP). The current (2007) focus of the CFRDP is on the Three Lakes watershed in Grand County, Colorado, which has applicability to many similar forested, mountain areas in the Western United States.

Tests for Z-direction fiber orientation

Treesearch

David W. Vahey; John M. Considine

2007-01-01

Fibers that acquire a Z-direction tilt in the forming process help bond adjacent strata of the paper sheet, increasing Z-direction shear and other properties. For certain tests, this manifests itself as a test difference upon 180° in-plane rotation of the sheet. Seven of eight different paper grades ranging in grammage from 73 to 268 g/m2 were found to show this...

Photographic copy of plan of new Dy horizontal station and ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Photographic copy of plan of new Dy horizontal station and accumulator additions to Test Stand "D," also showing existing Dd test station. JPL drawing by VTN Consolidated, Inc. Engineers, Architects, Planners, 2301 Campus Drive, Irvine, California 92664: "Jet Propulsion Laboratory-Edwards Test Station, Motive Steam Supply & Ejector Pumping System: Plan - Test Stand "D," sheet M-3 (JPL sheet number E24/33), 21 December 1976 - Jet Propulsion Laboratory Edwards Facility, Test Stand D, Edwards Air Force Base, Boron, Kern County, CA

Impact verification of space suit design for space station

NASA Technical Reports Server (NTRS)

Fish, Richard H.

1987-01-01

The ballistic limits of single sheet and double sheet structures made of 6061 T6 Aluminum of 1.8 mm and larger nominal thickness were investigated for projectiles of 1.5 mm diameter fired in the Vertical Gun Range Test Facility and NASA Ames Research Center. The hole diameters and sheet deformation behavior were studied for various ratios of sheet spacing to projectile diameter. The results indicate that for projectiles of less than 1.5 mm diameter the ballistic limit exceeds the nominal 10 km/sec orbital debris encounter velocity, if a single-sheet suit of 1.8 mm thickness is behind a single bumper sheet of 1 mm thickness spaced 12.5 mm apart.

Characterization of the mechanical and physical properties of TD-NiCr (Ni-20Cr-2ThO2) alloy sheet

NASA Technical Reports Server (NTRS)

Fritz, L. J.; Koster, W. P.; Taylor, R. E.

1973-01-01

Sheets of TD-NiCr processed using techniques developed to produce uniform material were tested to supply mechanical and physical property data. Two heats each of 0.025 and 0.051 cm thick sheet were tested. Mechanical properties evaluated included tensile, modulus of elasticity, Poisson's Ratio, compression, creep-rupture, creep strength, bearing strength, shear strength, sharp notch and fatigue strength. Test temperatures covered the range from ambient to 1589K. Physical properties were also studied as a function of temperature. The physical properties measured were thermal conductivity, linear thermal expansion, specific heat, total hemispherical emittance, thermal diffusivity, and electrical conductivity.

Effects of die quench forming on sheet thinning and 3-point bend testing of AA7075-T6

NASA Astrophysics Data System (ADS)

Kim, Samuel; Omer, Kaab; Rahmaan, Taamjeed; Butcher, Clifford; Worswick, Michael

2017-10-01

Lab-scaled AA7075 aluminum side impact beams were manufactured using the die quenching technique in which the sheet was solutionized and then quenched in-die during forming to a super saturated solid state. Sheet thinning measurements were taken at various locations throughout the length of the part and the effect of lubricant on surface scoring and material pick-up on the die was evaluated. The as-formed beams were subjected to a T6 aging treatment and then tested in three-point bending. Simulations were performed of the forming and mechanical testing experiments using the LS-DYNA finite element code. The thinning and mechanical response was predicted well.

LIVVkit: An extensible, python-based, land ice verification and validation toolkit for ice sheet models

NASA Astrophysics Data System (ADS)

Kennedy, Joseph H.; Bennett, Andrew R.; Evans, Katherine J.; Price, Stephen; Hoffman, Matthew; Lipscomb, William H.; Fyke, Jeremy; Vargo, Lauren; Boghozian, Adrianna; Norman, Matthew; Worley, Patrick H.

2017-06-01

To address the pressing need to better understand the behavior and complex interaction of ice sheets within the global Earth system, significant development of continental-scale, dynamical ice sheet models is underway. Concurrent to the development of the Community Ice Sheet Model (CISM), the corresponding verification and validation (V&V) process is being coordinated through a new, robust, Python-based extensible software package, the Land Ice Verification and Validation toolkit (LIVVkit). Incorporated into the typical ice sheet model development cycle, it provides robust and automated numerical verification, software verification, performance validation, and physical validation analyses on a variety of platforms, from personal laptops to the largest supercomputers. LIVVkit operates on sets of regression test and reference data sets, and provides comparisons for a suite of community prioritized tests, including configuration and parameter variations, bit-for-bit evaluation, and plots of model variables to indicate where differences occur. LIVVkit also provides an easily extensible framework to incorporate and analyze results of new intercomparison projects, new observation data, and new computing platforms. LIVVkit is designed for quick adaptation to additional ice sheet models via abstraction of model specific code, functions, and configurations into an ice sheet model description bundle outside the main LIVVkit structure. Ultimately, through shareable and accessible analysis output, LIVVkit is intended to help developers build confidence in their models and enhance the credibility of ice sheet models overall.

Woven heat exchanger

DOEpatents

Piscitella, R.R.

1984-07-16

This invention relates to a heat exchanger for waste heat recovery from high temperature industrial exhaust streams. In a woven ceramic heat exchanger using the basic tube-in-shell design, each heat exchanger consisting of tube sheets and tube, is woven separately. Individual heat exchangers are assembled in cross-flow configuration. Each heat exchanger is woven from high temperature ceramic fiber, the warp is continuous from tube to tube sheet providing a smooth transition and unitized construction.

Bedrock geologic map of the Hartland and North Hartland quadrangles, Windsor County, Vermont, and Sullivan and Grafton Counties, New Hampshire

USGS Publications Warehouse

Walsh, Gregory J.

2016-08-16

This report consists of sheets 1 and 2 as well as an online geographic information systems database that includes contacts of bedrock geologic units, faults, outcrops, structural geologic information, and photographs. Sheet 2 of this report shows three cross sections, a tectonic map, and two brittle features maps that show measured outcrop-scale strike and dip results with summary stereonets and rose diagrams.

Missing Children. Missing Children Data Collected by the National Crime Information Center. Fact Sheet for the Honorable Alfonse M. D'Amato, United States Senate.

ERIC Educational Resources Information Center

General Accounting Office, Washington, DC.

This document is a fact sheet on missing children data collected by the National Crime Information Center (NCIC). The document contains details on the design of the NCIC system, state control for management and use of the system, access to the system, criteria for missing persons, number of active cases, and the unidentified persons file of the…

Top Languages Spoken by English Language Learners Nationally and by State. ELL Information Center Fact Sheet Series. No. 3

ERIC Educational Resources Information Center

Batalova, Jeanne; McHugh, Margie

2010-01-01

While English Language Learner (ELL) students in the United States speak more than 150 languages, Spanish is by far the most common home or first language, but is not the top language spoken by ELLs in every state. This fact sheet, based on analysis of the U.S. Census Bureau's 2009 American Community Survey, documents the top languages spoken…

Novel Task Functionalized Biopolymers for Enhanced Change Detection in Support of C-IED Operations

DTIC Science & Technology

2013-04-15

biopolymer was tested. All materials tested, PAM, chitin , the native biopolymer, and the MU conjugated biopolymer, were applied in small soil plots...phaseoli Strain 127 K36. Carbohydr. Res. 117, 141-156. EPA. 2001. Chitin ; Poly-N-acetyl-D-glucosamine (128991) Fact Sheet. USEPA Fact Sheet

REACH. Teacher's Guide Volume II. Check Points.

ERIC Educational Resources Information Center

Georgia Univ., Athens. Div. of Vocational Education.

Designed for use with individualized instructional units (CE 026 345-347, CE 026 349-351) in the REACH (Refrigeration, Electro-Mechanical, Air-Conditioning, Heating) electromechanical cluster, this second volume of the postsecondary teacher guide contains the check points which the instructor may want to refer to when the unit sheet directs the…

Entrepreneur Training Program. Getting Started.

ERIC Educational Resources Information Center

De Maria, Richard

This student workbook on starting a small business is part of the entrepreneur training program at Ocean County (New Jersey) Vocational-Technical Schools. The workbook consists of 16 units containing goals and objectives, study questions, exercises, sample materials, and information sheets. Unit topics are as follows: being a small business owner;…

Study Canada: An Overview.

ERIC Educational Resources Information Center

Monahan, Robert L.; And Others

The document presents the first of five units on Canada developed for classroom use in American secondary schools. This unit, an overview of Canada, offers a sequence of information sheets for students and class activity suggestions for teachers which use a comparative approach stressing an understanding of Canada from the viewpoints of both…

Specifications for Supplementary Classroom Units, Stressed Skin Panel.

ERIC Educational Resources Information Center

Waring, Robert B.; And Others

Complete outline specifications are given for the construction of supplementary classroom units using stressed skin panels. Sections included are--(1) concrete and related work, (2) masonry, (3) structural and miscellaneous metal, (4) curtain walls and metal windows, (5) carpentry and related work, (6) roofing, sheet metal, and related work, (7)…

Engineering Industry Training Board (EITB) Foundation Training. Unit 1.

ERIC Educational Resources Information Center

Engineering Industry Training Board, London (England).

This instructional unit deals with broadly based appreciation training in a range of skills that are appropriate to a wide sector of occupations, including engineering drawing, engineering materials, bench fitting, sheet metal work, turning, milling, welding, and electricity/electronics. The materials presented are intended for instructors and…

US Federal LCA Commons Life Cycle Inventory Unit Process Template

EPA Science Inventory

The US Federal LCA Commons Life Cycle Inventory Unit Process Template is a multi-sheet Excel template for life cycle inventory data, metadata and other documentation. The template comes as a package that consistent of three parts: (1) the main template itself for life cycle inven...

Engineering Industry Training Board (EITB) Foundation Training. Unit 2.

ERIC Educational Resources Information Center

Engineering Industry Training Board, London (England).

This instructional unit deals with broadly based appreciation training in a range of skills that are appropriate to a wide sector of occupations, including safety, engineering drawing, engineering materials, bench fitting, sheet metal work, turning, milling, welding, and electricity/electronics. The materials presented are intended for instructors…

Farm Business Management. Volume I. Vocational Agriculture Education.

ERIC Educational Resources Information Center

Hodgens, Jim; Meyers, Leland

This curriculum guide provides a basic core of instruction for the first year of a three-year adult program in farm business management. It contains 12 units of instruction. Each unit consists of seven basic components: performance objectives, teacher activities, information sheets (content essential for meeting the cognitive objectives),…

Small Business Course for Older Americans. Student Handbook.

ERIC Educational Resources Information Center

American Association of Community and Junior Colleges, Washington, DC.

This student handbook was designed for a course which offers people aged 55 and older guidance in starting and operating a small business. Following introductory remarks concerning small businesses, information and assignment sheets related to each of the course's basic units are presented. Course units include the following: (1) Small Business…

An evolved axial melt lens in the Northern Ibra Valley, Southern Oman Ophiolite

NASA Astrophysics Data System (ADS)

Loocke, M. P.; Lissenberg, C. J.; MacLeod, C. J.

2014-12-01

The axial melt lens (AML) is a common feature lying at the base of the upper crust at fast-spreading mid-ocean ridges. It is thought to play a major role in the evolution of MORB and, potentially, accretion of the plutonic lower crust. In order to better understand the petrological processes that operate in AMLs we have examined the nature and variability of the horizon equivalent to the AML preserved in the Oman ophiolite. We present the results of a detailed investigation of a section east of Fahrah in the Ibra Valley. Here, a suite of 'varitextured' gabbros separates the sheeted dykes above from foliated gabbros below. It comprises 3 distinct units: an ophitic gabbro with pegmatitic patches (patchy gabbro; 70 m thick), overlain by a spotty gabbro (50 m), capped by a quartz-diorite (120 m). The sheeted dykes are observed to root in the quartz-diorite. Contacts between the plutonic units are gradational and subhorizontal. All of the units are isotropic. A total of 110 samples were collected for detailed petrographic and chemical analysis. With the exception of a small number of the diorites, all of the samples have a 'cumulate' component. Primary igneous amphibole is ubiquitous, present even as a minor phase in the foliated gabbros beneath, and indicating extensive differentiation and/or the presence of water in the primary liquid. France et al. (2014, Lithos) report patches of granoblastic material from this horizon in the Fahrah area, and suggest they represent the restites of partially melted pieces of the sheeted dykes. We did not, however, find any such granoblastic material, nor can the quartz-diorites represent partial melt; instead, preliminary geochemical modeling suggests that all of the units can be related by simple progressive fractional crystallization of an Oman axial ('V1' or 'Geotimes') melt. Along with the field relationships, as well as the basaltic andesite to dacite composition of the overlying sheeted dykes, this suggests that the AML was the locus of formation of the highly evolved melts. This contrasts with the more primitive AML and sheeted dyke complex documented in Wadi Abyad. From this we conclude that there is significant lateral variability in AML compositions along the Oman ridge axis.

Formability of Annealed Ni-Ti Shape Memory Alloy Sheet

NASA Astrophysics Data System (ADS)

Fann, K. J.; Su, J. Y.; Chang, C. H.

2018-03-01

Ni-Ti shape memory alloy has two specific properties, superelasiticity and shape memory effect, and thus is widely applied in diverse industries. To extend its application, this study attempts to investigate the strength and cold formability of its sheet blank, which is annealed at various temperatures, by hardness test and by Erichsen-like cupping test. As a result, the higher the annealing temperature, the lower the hardness, the lower the maximum punch load as the sheet blank fractured, and the lower the Erichsen-like index or the lower the formability. In general, the Ni-Ti sheet after annealing has an Erichsen-like index between 8 mm and 9 mm. This study has also confirmed via DSC that the Ni-Ti shape memory alloy possesses the austenitic phase and shows the superelasticity at room temperature.

Smart photonic coating for civil engineering field: for a future inspection technology on concrete bridge

NASA Astrophysics Data System (ADS)

Fudouzi, Hiroshi; Tsuchiya, Koichi; Todoroki, Shin-ichi; Hyakutake, Tsuyoshi; Nitta, Hiroyuki; Nishizaki, Itaru; Tanaka, Yoshikazu; Ohya, Takao

2017-04-01

Here we will propose the conceptual new idea of the inspection of concrete bridge using smart materials and mobile IoT system. We apply opal photonic crystal film to detect cracks on concrete infrastructures. High quality opal photonic crystal films were coated on black color PET sheet over 1000 cm2 area. The opal film sheet was cut and adhered to concrete or mortar test pieces by epoxy resin. In the tensile test, the structural color of the opal sheet was changed when the crack was formed. As a demonstration, we have installated the opal film sheet on the wall of the concrete bridge. Our final purpose is the color change will be recorded by portable CCD devices, and send to expert via IoT network.

Development of a Cell Sheet Transportation Technique for Regenerative Medicine

PubMed Central

Oie, Yoshinori; Nozaki, Takayuki; Takayanagi, Hiroshi; Hara, Susumu; Hayashi, Ryuhei; Takeda, Shizu; Mori, Keisuke; Moriya, Noboru; Soma, Takeshi; Tsujikawa, Motokazu; Saito, Kazuo

2014-01-01

Purpose: A transportation technique for cell sheets is necessary to standardize regenerative medicine. The aim of this article is to develop and evaluate a new transportation technique for cell sheets. Material and Methods: We developed a transportation container with three basic functions: the maintenance of interior temperature, air pressure, and sterility. The interior temperature and air pressure were monitored by a recorder. Human oral mucosal epithelial cells obtained from two healthy volunteers were cultured on temperature-responsive culture dishes. The epithelial cell sheets were transported via an airplane between the Osaka University and Tohoku University using the developed cell transportation container. Histological and immunohistochemical analyses and flow cytometric analyses for cell viability and cell purity were performed for the cell sheets before and 12 h after transportation to assess the influence of transportation on the cell sheets. Sterility tests and screening for endotoxin and mycoplasma in the cell sheets were performed before and after transportation. Results: During transportation via an airplane, the temperature inside the container was maintained above 32°C, and the changes in air pressure remained within 10 hPa. The cell sheets were well stratified and successfully harvested before and after transportation. The expression patterns of keratin 3/76, p63, and MUC16 were equivalent before and after transportation. However, the expression of ZO-1 in the cell sheet after transportation was slightly weaker than that before transportation. The cell viability was 72.0% before transportation and 77.3% after transportation. The epithelial purity was 94.6% before transportation and 87.9% after transportation. Sterility tests and screening for endotoxin and mycoplasma were negative for all cell sheets. Conclusion: The newly developed transportation technique for air travel is essential technology for regenerative medicine and promotes the standardization and spread of regenerative therapies. PMID:24044382

Development of a cell sheet transportation technique for regenerative medicine.

PubMed

Oie, Yoshinori; Nozaki, Takayuki; Takayanagi, Hiroshi; Hara, Susumu; Hayashi, Ryuhei; Takeda, Shizu; Mori, Keisuke; Moriya, Noboru; Soma, Takeshi; Tsujikawa, Motokazu; Saito, Kazuo; Nishida, Kohji

2014-05-01

A transportation technique for cell sheets is necessary to standardize regenerative medicine. The aim of this article is to develop and evaluate a new transportation technique for cell sheets. We developed a transportation container with three basic functions: the maintenance of interior temperature, air pressure, and sterility. The interior temperature and air pressure were monitored by a recorder. Human oral mucosal epithelial cells obtained from two healthy volunteers were cultured on temperature-responsive culture dishes. The epithelial cell sheets were transported via an airplane between the Osaka University and Tohoku University using the developed cell transportation container. Histological and immunohistochemical analyses and flow cytometric analyses for cell viability and cell purity were performed for the cell sheets before and 12 h after transportation to assess the influence of transportation on the cell sheets. Sterility tests and screening for endotoxin and mycoplasma in the cell sheets were performed before and after transportation. During transportation via an airplane, the temperature inside the container was maintained above 32°C, and the changes in air pressure remained within 10 hPa. The cell sheets were well stratified and successfully harvested before and after transportation. The expression patterns of keratin 3/76, p63, and MUC16 were equivalent before and after transportation. However, the expression of ZO-1 in the cell sheet after transportation was slightly weaker than that before transportation. The cell viability was 72.0% before transportation and 77.3% after transportation. The epithelial purity was 94.6% before transportation and 87.9% after transportation. Sterility tests and screening for endotoxin and mycoplasma were negative for all cell sheets. The newly developed transportation technique for air travel is essential technology for regenerative medicine and promotes the standardization and spread of regenerative therapies.

Interpretation of high-speed flows in the plasma sheet

NASA Technical Reports Server (NTRS)

Chen, C. X.; Wolf, R. A.

1993-01-01

Pursuing an idea suggested by Pontius and Wolf (1990), we propose that the `bursty bulk flows' observed by Baumjohann et al. (1990) and Angelopoulos et al. (1992) are `bubbles' in the Earth's plasma sheet. Specifically, they are flux tubes that have lower values of pV(exp 5/3) than their neighbors, where p is the thermal pressure of the particles and V is the volume of a tube containing one unit of magnetic flux. Whether they are created by reconnection or some other mechanism, the bubbles are propelled earthward by a magnetic buoyancy force, which is related to the interchange instability. Most of the major observed characteristics of the bursty bulk flows can be interpreted naturally in terms of the bubble picture. We propose a new `stratified fluid' picture of the plasma sheet, based on the idea that bubbles constitute the crucial transport mechanism. Results from simple mathematical models of plasma sheet transport support the idea that bubbles can resolve the pressure balance inconsistency, particularly in cases where plasma sheet ions are lost by gradient/curvature drift out the sides of the tail or bubbles are generated by reconnection in the middle of plasma sheet.

Development of the apparatus for measuring magnetic properties of electrical steel sheets in arbitrary directions under compressive stress normal to their surface

NASA Astrophysics Data System (ADS)

Maeda, Yoshitaka; Urata, Shinya; Nakai, Hideo; Takeuchi, Yuuya; Yun, Kyyoul; Yanase, Shunji; Okazaki, Yasuo

2017-05-01

In designing motors, one must grasp the magnetic properties of electrical steel sheets considering actual conditions in motors. Especially important is grasping the stress dependence of magnetic power loss. This paper describes a newly developed apparatus to measure two-dimensional (2-D) magnetic properties (properties under the arbitrary alternating and the rotating flux conditions) of electrical steel sheets under compressive stress normal to the sheet surface. The apparatus has a 2-D magnetic excitation circuit to generate magnetic fields in arbitrary directions in the evaluation area. It also has a pressing unit to apply compressive stress normal to the sheet surface. During measurement, it is important to apply uniform stress throughout the evaluation area. Therefore, we have developed a new flux density sensor using needle probe method. It is composed of thin copper foils sputtered on electrical steel sheets. By using this sensor, the stress can be applied to the surface of the specimen without influence of this sensor. This paper described the details of newly developed apparatus with this sensor, and measurement results of iron loss by using are shown.

Simple liquid crystal display backlight unit comprising only a single-sheet micropatterned polydimethylsiloxane (PDMS) light-guide plate.

PubMed

Lee, Joo-Hyung; Lee, Hong-Seok; Lee, Byung-Kee; Choi, Won-Seok; Choi, Hwan-Young; Yoon, Jun-Bo

2007-09-15

A simple liquid crystal display (LCD) backlight unit (BLU) comprising only a single-sheet polydimethylsiloxane (PDMS) light-guide plate (LGP) has been developed. The PDMS LGP, having micropatterns with an inverse-trapezoidal cross section, was fabricated by backside 3-D diffuser lithography followed by PDMS-to-PDMS replication. The fabricated BLU showed an average luminance of 2878 cd/m(2) with 73.3% uniformity when mounted in a 5.08 cm backlight module with four side view 0.85cd LEDs. The developed BLU can greatly reduce the cost and thickness of LCDs, and it can be applied to flexible displays as a flexible light source due to the flexible characteristic of the PDMS itself.

NASA Dryden flow visualization facility

NASA Technical Reports Server (NTRS)

Delfrate, John H.

1995-01-01

This report describes the Flow Visualization Facility at NASA Dryden Flight Research Center, Edwards, California. This water tunnel facility is used primarily for visualizing and analyzing vortical flows on aircraft models and other shapes at high-incidence angles. The tunnel is used extensively as a low-cost, diagnostic tool to help engineers understand complex flows over aircraft and other full-scale vehicles. The facility consists primarily of a closed-circuit water tunnel with a 16- x 24-in. vertical test section. Velocity of the flow through the test section can be varied from 0 to 10 in/sec; however, 3 in/sec provides optimum velocity for the majority of flow visualization applications. This velocity corresponds to a unit Reynolds number of 23,000/ft and a turbulence level over the majority of the test section below 0.5 percent. Flow visualization techniques described here include the dye tracer, laser light sheet, and shadowgraph. Limited correlation to full-scale flight data is shown.

PILING PLAN OF SHIPBUILDING WAYS AND WHIRLEY CRANE SUPPORT. United ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

PILING PLAN OF SHIPBUILDING WAYS AND WHIRLEY CRANE SUPPORT. United Engineering Company Ltd., Alameda Shipbuilding Plant. General plan and two sections. James J. Walsh, Consulting Engineer. Sheet no. 2. Scales 1 inch to 10 feet, and 1/4 inch to one foot. April 20, 1941, revised 5/7/41. blueprint - United Engineering Company Shipyard, Shipway Nos. 1 & 2, 2900 Main Street, Alameda, Alameda County, CA

Units of Instruction for Vocational Office Education. Volume 2. Office Occupations--Related Information, Accounting and Computing Occupations, Information Communications Occupations, Stenographic, Secretarial, and Related Occupations. Teacher's Guide.

ERIC Educational Resources Information Center

East Texas State Univ., Commerce. Occupational Curriculum Lab.

Sixteen units on office occupations are presented in this teacher's guide. The unit topics include the following: related information (e.g., preparing for job interview); accounting and computing (e.g., preparing a payroll and a balance sheet); information communications (e.g., handling appointments, composing correspondence); and stenographic,…

The Utility of Corporate-Style Balance Sheets for DoD Managers

DTIC Science & Technology

2014-06-01

operations of the executive branch ( United States Department of Commerce, 2014, p. 3- 2). 19 5. The Federal Financial Management Improvement Act of...federal financial management systems requirements, applicable federal accounting standards, and the United States Government Standard General Ledger at...General Accountability Office (1991). The Chief Financial Officers Act: A mandate for federal financial management reform. Washington, DC: Author. United

Development of a low energy micro sheet forming machine

NASA Astrophysics Data System (ADS)

Razali, A. R.; Ann, C. T.; Shariff, H. M.; Kasim, N. I.; Musa, M. A.; Ahmad, A. F.

2017-10-01

It is expected that with the miniaturization of materials being processed, energy consumption is also being `miniaturized' proportionally. The focus of this study was to design a low energy micro-sheet-forming machine for thin sheet metal application and fabricate a low direct current powered micro-sheet-forming machine. A prototype of low energy system for a micro-sheet-forming machine which includes mechanical and electronic elements was developed. The machine was tested for its performance in terms of natural frequency, punching forces, punching speed and capability, energy consumption (single punch and frequency-time based). Based on the experiments, the machine can do 600 stroke per minute and the process is unaffected by the machine's natural frequency. It was also found that sub-Joule of power was required for a single stroke of punching/blanking process. Up to 100micron thick carbon steel shim was successfully tested and punched. It concludes that low power forming machine is feasible to be developed and be used to replace high powered machineries to form micro-products/parts.

A preliminary investigation of projectile shape effects in hypervelocity impact of a double-sheet structure

NASA Technical Reports Server (NTRS)

Morrison, R. H.

1972-01-01

Impact tests of a sphere and several cylinders of various masses and fineness ratios, all of aluminum, fired into an aluminum double-sheet structure at velocities near 7 km/sec, show that a cylinder, impacting in the direction of its axis, is considerably more effective as a penetrator than a sphere. Impacts of three cylinders of equal mass, but different fineness ratios, produced holes through the structures' rear sheet, whereas impact of a sphere of the same mass did not. Moreover, it was found that to prevent rear-sheet penetration, the mass of the 1/2-fineness-ratio cylinder had to be reduced by a factor greater than three. Further tests wherein the cylinder diameter was held constant while the cylinder length was systematically reduced showed that a cylinder with a fineness ratio of 0.07 and a mass of only 1/7 that of the sphere was still capable of producing a hole in the rear sheet.

Springback evaluation of friction stir welded TWB automotive sheets

NASA Astrophysics Data System (ADS)

Kim, Junehyung; Lee, Wonoh; Chung, Kyung-Hwan; Kim, Daeyong; Kim, Chongmin; Okamoto, Kazutaka; Wagoner, R. H.; Chung, Kwansoo

2011-02-01

Springback behavior of automotive friction stir welded TWB (tailor welded blank) sheets was experimentally investigated and the springback prediction capability of the constitutive law was numerically validated. Four automotive sheets, aluminum alloy 6111-T4, 5083-H18, 5083-O and dual-phase DP590 steel sheets, each having one or two different thicknesses, were considered. To represent mechanical properties, the modified Chaboche type combined isotropic-kinematic hardening law was utilized along with the non-quadratic orthogonal anisotropic yield function, Yld2000-2d, while the anisotropy of the weld zone was ignored for simplicity. For numerical simulations, mechanical properties previously characterized [1] were applied. For validation purposes, three springback tests including the unconstrained cylindrical bending, 2-D draw bending and OSU draw-bend tests were carried out. The numerical method performed reasonably well in analyzing all verification tests and it was confirmed that the springback of TWB as well as of base samples is significantly affected by the ratio of the yield stress with respect to Young's modulus and thickness.

Experimental Characterization and Material Modelling of an AZ31 Magnesium Sheet Alloy at Elevated Temperatures under Consideration of the Tension-Compression Asymmetry

NASA Astrophysics Data System (ADS)

Behrens, B.-A.; Bouguecha, A.; Bonk, C.; Dykiert, M.

2017-09-01

Magnesium sheet alloys have a great potential as a construction material in the aerospace and automotive industry. However, the current state of research regarding temperature dependent material parameters for the description of the plastic behaviour of magnesium sheet alloys is scarce in literature and accurate statements concerning yield criteria and appropriate characterization tests to describe the plastic behaviour of a magnesium sheet alloy at elevated temperatures in deep drawing processes are to define. Hence, in this paper the plastic behaviour of the well-established magnesium sheet alloy AZ31 has been characterized by means of convenient mechanical tests (e. g. tension, compression and biaxial tests) at temperatures between 180 and 230 °C. In this manner, anisotropic and hardening behaviour as well as differences between the tension-compression asymmetry of the yield locus have been estimated. Furthermore, using the evaluated data from the above mentioned tests, two different yield criteria have been parametrized; the commonly used Hill’48 and an orthotropic yield criterion, CPB2006, which was developed especially for materials with hexagonal close packed lattice structure and is able to describe an asymmetrical yielding behaviour regarding tensile and compressive stress states. Numerical simulations have been finally carried out with both yield functions in order to assess the accuracy of the material models.

USEEIO Satellite Tables

EPA Pesticide Factsheets

These files contain the environmental data as particular emissions or resources associated with a BEA sectors that are used in the USEEIO model. They are organized by the emission or resources type, as described in the manuscript. The main files (without SI) show the final satellite tables in the 'Exchanges' sheet which have emissions or resource use per USD for 2013. The other sheets in these files provide meta data for the create of the tables, including general information, sources, etc. The 'export' sheet is used for saving the satellite table for csv export. The data dictionary describes the fields in this sheet. The supporting files provide all the details data transformation and organization for the development of the satellite tables.This dataset is associated with the following publication:Yang, Y., W. Ingwersen, T. Hawkins, and D. Meyer. USEEIO: a New and Transparent United States Environmentally Extended Input-Output Model. JOURNAL OF CLEANER PRODUCTION. Elsevier Science Ltd, New York, NY, USA,

Preforming of polydioxanone sheets for orbital wall fractures - A technical note.

PubMed

Kruber, Daniel; Hierl, Thomas; Doerfler, Hans-Martin; Huempfner-Hierl, Heike; Krause, Matthias

2018-07-01

Polydioxanone (PDS) sheets are commonly used in the treatment of orbital wall fractures. A potential drawback of PDS is that it may be difficult to adapt to the anatomy of the orbital walls. Therefore a study was conceived to test the feasibility of preforming PDS sheets. PDS sheet material was water-heated and preformed using a template based on a statistical anatomical model. Then the deformed sheet was cooled, stored and compared to the original model to investigate post-deformation changes. PDS sheet material could easily be deformed using a mould. No significant post-cooling shape changes were noticed. PDS sheet material can be preformed into complex geometric shapes. This could be a benefit in the treatment of orbital wall fractures. Copyright © 2018 European Association for Cranio-Maxillo-Facial Surgery. Published by Elsevier Ltd. All rights reserved.

Film holder for radiographing tubing

DOEpatents

Davis, Earl V.; Foster, Billy E.

1976-01-01

A film cassette is provided which may be easily placed about tubing or piping and readily held in place while radiographic inspection is performed. A pair of precurved light-impervious semi-rigid plastic sheets, hinged at one edge, enclose sheet film together with any metallic foils or screens. Other edges are made light-tight with removable caps, and the entire unit is held securely about the object to be radiographed with a releasable fastener such as a strip of Velcro.

Indian Renewable Energy and Energy Efficiency Policy Database (Fact Sheet)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bushe, S.

2013-09-01

This fact sheet provides an overview of the Indian Renewable Energy and Energy Efficiency Policy Database (IREEED) developed in collaboration by the United States Department of Energy and India's Ministry of New and Renewable Energy. IREEED provides succinct summaries of India's central and state government policies and incentives related to renewable energy and energy efficiency. The online, public database was developed under the U.S.- India Energy Dialogue and the Clean Energy Solution Center.

A Module Experimental Process System Development Unit (MEPSDU)

NASA Technical Reports Server (NTRS)

1982-01-01

Restructuring research objectives from a technical readiness demonstration program to an investigation of high risk, high payoff activities associated with producing photovoltaic modules using non-CZ sheet material is reported. Deletion of the module frame in favor of a frameless design, and modification in cell series parallel electrical interconnect configuration are reviewed. A baseline process sequence was identified for the fabrication of modules using the selected dendritic web sheet material, and economic evaluations of the sequence were completed.

(2E)-3-(6-methoxynaphthalen-2-yl)-1-(pyridin-3-yl)prop-2-en-1-one and its cyclocondensation product with guanidine, (4RS)-2-amino-4-(6-methoxynaphthalen-2-yl)-6-(pyridin-3-yl)-3,4-dihydropyrimidine monohydrate: two types of hydrogen-bonded sheet.

PubMed

Nayak, Prakash S; Narayana, Badiadka; Yathirajan, Hemmige S; Hosten, Eric C; Betz, Richard; Glidewell, Christopher

2014-11-01

The structures of a chalcone and of its cyclocondensation product with guanidine are reported. In (2E)-3-(6-methoxynaphthalen-2-yl)-1-(pyridin-3-yl)prop-2-en-1-one, C19H15NO2, (I), the planes of the pyridine and naphthalene units make dihedral angles with that of the central spacer unit of 23.61 (13) and 23.57 (15)°, respectively, and a dihedral angle of 47.24 (9)° with each other. The molecules of (I) are linked into sheets by a combination of C-H···O and C-H···π(arene) hydrogen bonds. In the cyclocondensation product (4RS)-2-amino-4-(6-methoxynaphthalen-2-yl)-6-(pyridin-3-yl)-3,4-dihydropyrimidine monohydrate, C20H18N4O·H2O, (II), the dihydropyrimidine ring adopts a conformation best described as a shallow boat. The molecular components are linked by two N-H···O hydrogen bonds, two O-H···N hydrogen bonds and one N-H···N hydrogen bond to form complex sheets, with the methoxynaphthalene interdigitated between inversion-related pairs of sheets.

Freestanding two-dimensional Ni(OH)2 thin sheets assembled by 3D nanoflake array as basic building units for supercapacitor electrode materials.

PubMed

Song, Dianmei; Zhu, Jikui; Xuan, Liying; Zhao, Chenglan; Xie, Li; Chen, Lingyun

2018-01-01

Freestanding two dimensional (2D) porous nanostructures have great potential in electrical energy storage. In the present work, we reported the first synthesis of two-dimensional (2D) β-Ni(OH) 2 thin sheets (CQU-Chen-Ni-O-H-1) assembled by 3D nanoflake array as basic building units under acid condition by direct hydrothermal decomposition of the mixed solution of nickel nitrate (Ni(NO 3 ) 2 ) and acetic acid (CH 3 COOH, AA). The unique 3D nanoflake array assembled mesoporous 2D structures endow the thin sheets with a high specific capacitance of 1.78Fcm -2 (1747.5Fg -1 ) at the current density of 1.02mAcm -2 and good rate capability of 67.4% retain from 1.02 to 10.2mAcm -2 . The corresponding assembled asymmetric supercapacitor (ASC) achieves (CQU-Chen-Ni-O-H-1//active carbon (AC)) a high voltage of 1.8V and an energy density of 23.45Whkg -1 with a maximum power density of 9kWkg -1 , as well as cycability with 93.6% capacitance retention after 10,000 cycles. These results show the mesoporous thin sheets have great potential for SCs and other energy storage devices. Copyright © 2017 Elsevier Inc. All rights reserved.

Development of lightweight graphite/polyimide sandwich panels, phases 3, 4 and 5

NASA Technical Reports Server (NTRS)

Merlette, J. B.

1972-01-01

Work performed in the last three phases of the program included: (1) face sheet processing; (2) honeycomb core manufacture; (3) face sheet-to-core bonding development; and (4) sandwich panel fabrication and testing. Resin cure studies were a major portion of this effort since processing problems traced to the polyimide matrix resin had to be resolved before quality core and face sheets could be fabricated. Honeycomb core fabrication and testing were conducted by Hexcel Corporation. A total of four graphite/polyimide resin composite cores were fabricated, tested, and reported. Two sandwich panels weighing .48 and .58 lb/sq ft, respectively were designed and fabricated which meet the support structure loads for the shuttle orbiter thermal protection system.

LIVVkit: An extensible, python-based, land ice verification and validation toolkit for ice sheet models

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kennedy, Joseph H.; Bennett, Andrew R.; Evans, Katherine J.

To address the pressing need to better understand the behavior and complex interaction of ice sheets within the global Earth system, significant development of continental-scale, dynamical ice sheet models is underway. Concurrent to the development of the Community Ice Sheet Model (CISM), the corresponding verification and validation (V&V) process is being coordinated through a new, robust, Python-based extensible software package, the Land Ice Verification and Validation toolkit (LIVVkit). Incorporated into the typical ice sheet model development cycle, it provides robust and automated numerical verification, software verification, performance validation, and physical validation analyses on a variety of platforms, from personal laptopsmore » to the largest supercomputers. LIVVkit operates on sets of regression test and reference data sets, and provides comparisons for a suite of community prioritized tests, including configuration and parameter variations, bit-for-bit evaluation, and plots of model variables to indicate where differences occur. LIVVkit also provides an easily extensible framework to incorporate and analyze results of new intercomparison projects, new observation data, and new computing platforms. LIVVkit is designed for quick adaptation to additional ice sheet models via abstraction of model specific code, functions, and configurations into an ice sheet model description bundle outside the main LIVVkit structure. Furthermore, through shareable and accessible analysis output, LIVVkit is intended to help developers build confidence in their models and enhance the credibility of ice sheet models overall.« less

LIVVkit: An extensible, python-based, land ice verification and validation toolkit for ice sheet models

DOE PAGES

Kennedy, Joseph H.; Bennett, Andrew R.; Evans, Katherine J.; ...

2017-03-23

To address the pressing need to better understand the behavior and complex interaction of ice sheets within the global Earth system, significant development of continental-scale, dynamical ice sheet models is underway. Concurrent to the development of the Community Ice Sheet Model (CISM), the corresponding verification and validation (V&V) process is being coordinated through a new, robust, Python-based extensible software package, the Land Ice Verification and Validation toolkit (LIVVkit). Incorporated into the typical ice sheet model development cycle, it provides robust and automated numerical verification, software verification, performance validation, and physical validation analyses on a variety of platforms, from personal laptopsmore » to the largest supercomputers. LIVVkit operates on sets of regression test and reference data sets, and provides comparisons for a suite of community prioritized tests, including configuration and parameter variations, bit-for-bit evaluation, and plots of model variables to indicate where differences occur. LIVVkit also provides an easily extensible framework to incorporate and analyze results of new intercomparison projects, new observation data, and new computing platforms. LIVVkit is designed for quick adaptation to additional ice sheet models via abstraction of model specific code, functions, and configurations into an ice sheet model description bundle outside the main LIVVkit structure. Furthermore, through shareable and accessible analysis output, LIVVkit is intended to help developers build confidence in their models and enhance the credibility of ice sheet models overall.« less

3D Printing of Thermo-Responsive Methylcellulose Hydrogels for Cell-Sheet Engineering.

PubMed

Cochis, Andrea; Bonetti, Lorenzo; Sorrentino, Rita; Contessi Negrini, Nicola; Grassi, Federico; Leigheb, Massimiliano; Rimondini, Lia; Farè, Silvia

2018-04-10

A possible strategy in regenerative medicine is cell-sheet engineering (CSE), i.e., developing smart cell culture surfaces from which to obtain intact cell sheets (CS). The main goal of this study was to develop 3D printing via extrusion-based bioprinting of methylcellulose (MC)-based hydrogels. Hydrogels were prepared by mixing MC powder in saline solutions (Na₂SO₄ and PBS). MC-based hydrogels were analyzed to investigate the rheological behavior and thus optimize the printing process parameters. Cells were tested in vitro on ring-shaped printed hydrogels; bulk MC hydrogels were used for comparison. In vitro tests used murine embryonic fibroblasts (NIH/3T3) and endothelial murine cells (MS1), and the resulting cell sheets were characterized analyzing cell viability and immunofluorescence. In terms of CS preparation, 3D printing proved to be an optimal approach to obtain ring-shaped CS. Cell orientation was observed for the ring-shaped CS and was confirmed by the degree of circularity of their nuclei: cell nuclei in ring-shaped CS were more elongated than those in sheets detached from bulk hydrogels. The 3D printing process appears adequate for the preparation of cell sheets of different shapes for the regeneration of complex tissues.

Stabilizing benzene-like planar N6 rings to form a single atomic honeycomb BeN3 sheet with high carrier mobility.

PubMed

Li, Xiaoyin; Zhang, Shunhong; Zhang, Cunzhi; Wang, Qian

2018-01-18

It is a longstanding quest to use the planar N 6 ring as a structural unit to build stable atomic sheets. However, unlike C 6 H 6 , the neutral N 6 ring is unstable due to the strong repulsion of the lone-pair of electrons. Using first-principles calculations and the global structure search method, we show that the N 6 unit can be stabilized by the linkage of Be atoms, forming a h-BeN 3 honeycomb monolayer, in which the geometry and the π-molecular orbitals of the N 6 rings are well kept. This sheet is not only energetically, dynamically and thermally stable, but also can withstand high temperatures up to 1000 K. Band structure calculation combined with a group theory analysis and a tight-binding model uncover that h-BeN 3 has a π-band dominated band structure with an indirect band gap of 1.67 eV. While it possesses a direct band gap of 2.07 eV at the Γ point lying in the photon energy region of visual light, its interband dipole transition is symmetrically allowed so that electrons can be excited by photons free of phonons. Based on deformation potential theory, a systematic study of the transport properties reveals that the h-BeN 3 sheet possesses a high carrier mobility of ∼10 3 cm 2 V -1 s -1 , superior to the extensively studied transition metal dichalcogenide monolayers. We further demonstrate that this sheet can be rolled up into either zigzag or armchair nanotubes. These nanotubes are also dynamically stable, and are all direct band gap semiconductors with carrier mobility comparable to that of their 2D counterparts, regardless of their chirality and diameter. The robust stability and novel electronic and transport properties of the h-BeN 3 sheet and its tubular derivatives endow them with great potential for applications in nanoelectronic devices.

Food Marketing: Cashier-Checker. Student Material. Competency Based Curriculum.

ERIC Educational Resources Information Center

Froelich, Larry; And Others

This curriculum for food marketing (cashier-checking) is designed to provide entry-level employment skills. It is organized into 13 units which contain one to ten competencies. A student competency sheet provided for each competency is organized into this format: unit and competency number and name, learning steps, learning activities, and…

Fact Sheet on Women of Spanish Origin in the United States.

ERIC Educational Resources Information Center

Employment Standards Administration (DOL), Washington, DC. Women's Bureau.

March 1971 data are given for women of Spanish origin in the United States. Country of origin, population, family composition, educational attainment, labor force participation, type of work, income, and low income level are covered. Where separate data for women are not available, data for both sexes are shown. (KM)

Cultural Systems and Land Use Decision Making.

ERIC Educational Resources Information Center

Schaefer, Larry; Pressman, Rob

This material includes student guide sheets, reference material, and tape script for the audio-tutorial unit on Cultural Systems. An audio tape is used with the materials. The material is designed for use with Connecticut schools, but can be adapted to other localities. The materials in this unit consider components of cultural systems, land use…

Synthesis: Part I, Buildability.

ERIC Educational Resources Information Center

Pressman, Rob

This unit is designed to show the student how to pull together information on natural and man-managed systems to develop a coherent and environmentally sound plan of action. The material includes student guide sheets, reference material, and a tape script. Audiotapes are usually used with the materials. The unit assumes the student has studied a…

Local Implementation and Land Use Decision Making.

ERIC Educational Resources Information Center

Garlasco, Chris; And Others

This material includes student guide sheets, reference material, and tape script for the audio-tutorial unit on Local Implementation. An audio tape is used with the materials. The material is designed for use with Connecticut schools, but can be adapted to other localities. The material in this unit emphasizes the role of planning and zoning in…

A Guide to the Selection of Cost-Effective Wastewater Treatment Systems. Technical Report.

ERIC Educational Resources Information Center

Van Note, Robert H.; And Others

The data within this publication provide guidelines for planners, engineers and decision-makers at all governmental levels to evaluate cost-effectiveness of alternative wastewater treatment proposals. The processes described include conventional and advanced treatment units as well as most sludge handling and processing units. Flow sheets, cost…

CASA Fact Sheet.

ERIC Educational Resources Information Center

National Court Appointed Special Advocate Association, Seattle WA.

Each year nearly 400,000 children in the United States are thrust into court through no fault of their own. Often these children also become victims of the United States' overburdened child welfare system. A Court Appointed Special Advocate (CASA) volunteer is a trained citizen who is appointed by a judge to represent the best interests of a child…

Biotechnology in Agriculture. Teacher Edition.

ERIC Educational Resources Information Center

Peterson, Dennis R.; Rehberger, Thomas

This curriculum guide is designed to help teachers to present a course that emphasizes the interrelationship of science and technology and the impact of this technology on agriculture and agricultural products. The guide contains six units that each contain some or all of the following basic components of a unit of instruction: objective sheet,…

Automatic Transmission/Transaxle Specialist. Instructor Manual and Student Workbook. Automotive Service Series.

ERIC Educational Resources Information Center

Oklahoma State Dept. of Vocational and Technical Education, Stillwater. Curriculum and Instructional Materials Center.

This curriculum guide for transmission/transaxle specialist is one in a series of automotive service speciality publications that is based on the National Institute of Automotive Service Excellence task lists. The curriculum contains nine units. Each unit of instruction includes some or all of the following components: objective sheet,…

78 FR 60311 - Polyethylene Terephthalate Film, Sheet, and Strip From Brazil, China, and the United Arab...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-10-01

... conditions or business cycle for the Domestic Like Product that have occurred in the United States or in the... Official, at 202-205-3088. Limited disclosure of business proprietary information (BPI) under an... trade/business association; import/export Subject Merchandise from more than one Subject Country; or...

The United States Copyright Law: A Guide for Music Educators.

ERIC Educational Resources Information Center

National Association of Schools of Music, Reston, VA.

Music educators are informed of the applications of the 1976 revision of the United States copyright law to the use of sheet music, audiovisual recordings, and dramatic and choreographic works. Material is divided into five sections. Section 1 outlines the primary rights of copyright holders with regard to phonorecords, derivative works,…

Radiology Aide. Instructor Key [and] Student Manual.

ERIC Educational Resources Information Center

Hartwein, Jon; Dunham, John

This manual can be used independently by students in secondary health occupations programs or by persons receiving on-the-job training in a radiology department. The manual includes an instructor's key that provides answers to the activity sheets and unit evaluations. The manual consists of the following five units: (1) orientation to radiology;…

EnviroAtlas - Percent Stream Buffer Zone As Natural Land Cover for the Conterminous United States

EPA Pesticide Factsheets

This EnviroAtlas dataset shows the percentage of land area within a 30 meter buffer zone along the National Hydrography Dataset (NHD) high resolution stream network, and along water bodies such as lakes and ponds that are connected via flow to the streams, that is classified as forest land cover, modified forest land cover, and natural land cover using the 2006 National Land Cover Dataset (NLCD) for each Watershed Boundary Dataset (WBD) 12-digit hydrological unit (HUC) in the conterminous United States. This dataset was produced by the US EPA to support research and online mapping activities related to EnviroAtlas. EnviroAtlas (https://www.epa.gov/enviroatlas) allows the user to interact with a web-based, easy-to-use, mapping application to view and analyze multiple ecosystem services for the contiguous United States. The dataset is available as downloadable data (https://edg.epa.gov/data/Public/ORD/EnviroAtlas) or as an EnviroAtlas map service. Additional descriptive information about each attribute in this dataset can be found in its associated EnviroAtlas Fact Sheet (https://www.epa.gov/enviroatlas/enviroatlas-fact-sheets).

A discontinuous melt sheet in the Manson impact structure

NASA Technical Reports Server (NTRS)

Izett, G. A.; Reynolds, R. L.; Rosenbaum, J. G.; Nishi, J. M.

1993-01-01

Petrologic studies of the core recovered from holes drilled in the Manson, Iowa, buried impact structure may unravel the thermal history of the crater-fill debris. We made a cursory examination of about 200 m of core recovered from the M-1 bore hole. The M-1 bore hole was the first of 12 holes drilled as part of a cooperative drilling program between the U.S. Geological Survey and the Iowa Geological Survey Bureau. The M-1 core hole is about 6 km northeast of the center of the impact structure, apparently on the flank of its central peak. We developed a working hypothesis that a 30-m-thick breccia unit within a 53-m-thick unit previously termed the 'crystalline clast breccia with glassy matrix' is part of a discontinuous melt sheet in the crater-fill impact debris. The 30-m-thick breccia unit reached temperatures sufficient to partially melt some small breccia clasts and convert the fine-grained breccia matrix into a silicate melt that cooled to a greenish-black, flinty, microcrystalline rock. The results of the investigation of this unit are presented.

Texture and mechanical properties of Al-0.5Mg-1.0Si-0.5Cu alloy sheets manufactured via a cross rolling method

NASA Astrophysics Data System (ADS)

Jeon, Jae-Yeol; Son, Hyeon-Taek; Woo, Kee-Do; Lee, Kwang-Jin

2012-04-01

The relationship between the texture and mechanical properties of 6xxx aluminum alloy sheets processed via cross rolling was investigated. The microstructures of the conventional rolled and cross rolled sheets after annealing were analyzed using optical micrographs (OM). The texture distribution across the thickness in the Al-Mg-Si-Cu alloy, conventional rolled sheets, and cross rolled sheets both before and after annealing was investigated via X-ray texture measurements. The texture was analyzed in three layers from the surface to the center of the sheet. The β-fiber texture of the conventional rolled sheet was typical of the texture obtained using aluminumoll ring. After annealing, the typical β-fiber orientations were changed to recrystallization textures: cube{001}<100> and normal direction (ND)-rotated cubes. However, the texture of the cross rolled sheet was composed of an asymmetrical, rolling direction (RD)-rotated cubes. After annealing, the asymmetrical orientations in the cross rolled sheet were changed to a randomized texture. The average R-value of the annealed cross rolled sheets was higher than that of the conventional rolled sheets. The limit dome height (LDH) test results demonstrated that cross rolling is effective in improving the formability of the Al-Mg-Si-Cu alloy sheets.

Moldable cork ablation material

NASA Technical Reports Server (NTRS)

1977-01-01

A successful thermal ablative material was manufactured. Moldable cork sheets were tested for density, tensile strength, tensile elongation, thermal conductivity, compression set, and specific heat. A moldable cork sheet, therefore, was established as a realistic product.

Observations on the relationship of structure to the mechanical properties of thin TD-NiCr sheet

NASA Technical Reports Server (NTRS)

Whittenberger, J. D.

1976-01-01

A study of the relationship between structure and mechanical properties of thin TD-NiCr sheet indicated that the elevated temperature tensile, stress-rupture, and creep strength properties are dependent on grain aspect ratio and sheet thickness. In general, the strength properties increase with increasing grain aspect ratio and sheet thickness. Tensile testing revealed an absence of ductility at elevated temperatures (not less than 1144 K). Significant creep damage as determined by subsequent tensile testing at room temperature occurs after very small amounts (less than 0.1%) of prior creep deformation over the temperature range 1144-1477 K. A threshold stress for creep appears to exist. Creep exposure below the threshold stress at T not less than 1366 K results in almost full retention of room temperature tensile properties.

Modelling the climate and ice sheets of the mid-Pliocene warm period: a test of model dependency

NASA Astrophysics Data System (ADS)

Dolan, Aisling; Haywood, Alan; Lunt, Daniel; Hill, Daniel

2010-05-01

The mid-Pliocene warm period (MPWP; c. 3.0 - 3.3 million years ago) has been the subject of a large number of published studies during the last decade. It is an interval in Earth history, where conditions were similar to those predicted by climate models for the end of the 21st Century. Not only is it important to increase our understanding of the climate dynamics in a warmer world, it is also important to determine exactly how well numerical models can retrodict a climate significantly different from the present day, in order to have confidence in them for predicting the future climate. Previous General Circulation Model (GCM) simulations have indicated that MPWP mean annual surface temperatures were on average 2 to 3˚C warmer than the pre-industrial era. Coastal stratigraphy and benthic oxygen isotope records suggest that terrestrial ice volumes were reduced when compared to modern. Ice sheet modelling studies have supported this decrease in cryospheric extent. Generally speaking, both climate and ice sheet modelling studies have only used results from one numerical model when simulating the climate of the MPWP. However, recent projects such as PMIP (the Palaeoclimate Modelling Intercomparison Project) have emphasised the need to explore the dependency of past climate predictions on the specific climate model which is used. Here we present a comparison of MPWP climatologies produced by three atmosphere only GCMs from the Goddard Institute of Space Studies (GISS), the National Centre for Atmospheric Research (NCAR) and the Hadley Centre for Climate Prediction and Research (GCMAM3, CAM3-CLM and HadAM3 respectively). We focus on the ability of the GCMs to simulate climate fields needed to drive an offline ice sheet model to assess whether there are any significant differences between the climatologies. By taking the different temperature and precipitation predictions simulated by the three models as a forcing, and adopting GCM-specific topography, we have used the British Antarctic Survey thermomechanically coupled ice sheet model (BASISM) to test the extent to which equilibrium state ice sheets in the Northern Hemisphere are GCM dependent. Initial results which do not use GCM-specific topography suggest that employing different GCM climatologies with only small differences in surface air temperature and precipitation has a dramatic effect on the resultant Greenland ice sheet, where the end-member ice sheets vary from near modern to almost zero ice volume. As an extension of this analysis, we will also present results using a second ice sheet model (Glimmer), with a view to testing the degree to which end-member ice sheets are ice sheet model dependent, something which has not previously been addressed. Initially, BASISM and Glimmer will be internally optimised for performance, but we will also present a comparison where BASISM will be configured to the Glimmer model setup in a further test of ice sheet model dependency.

Laser based spot weld characterization

NASA Astrophysics Data System (ADS)

Jonietz, Florian; Myrach, Philipp; Rethmeier, Michael; Suwala, Hubert; Ziegler, Mathias

2016-02-01

Spot welding is one of the most important joining technologies, especially in the automotive industry. Hitherto, the quality of spot welded joints is tested mainly by random destructive tests. A nondestructive testing technique offers the benefit of cost reduction of the testing procedure and optimization of the fabrication process, because every joint could be examined. This would lead to a reduced number of spot welded joints, as redundancies could be avoided. In the procedure described here, the spot welded joint between two zinc-coated steel sheets (HX340LAD+Z100MB or HC340LA+ZE 50/50) is heated optically on one side. Laser radiation and flash light are used as heat sources. The melted zone, the so called "weld nugget" provides the mechanical stability of the connection, but also constitutes a thermal bridge between the sheets. Due to the better thermal contact, the spot welded joint reveals a thermal behavior different from the surrounding material, where the heat transfer between the two sheets is much lower. The difference in the transient thermal behavior is measured with time resolved thermography. Hence, the size of the thermal contact between the two sheets is determined, which is directly correlated to the size of the weld nugget, indicating the quality of the spot weld. The method performs well in transmission with laser radiation and flash light. With laser radiation, it works even in reflection geometry, thus offering the possibility of testing with just one-sided accessibility. By using heating with collimated laser radiation, not only contact-free, but also remote testing is feasible. A further convenience compared to similar thermographic approaches is the applicability on bare steel sheets without any optical coating for emissivity correction. For this purpose, a proper way of emissivity correction was established.

Fatigue Strength and Related Characteristics of Aircraft Joints I : Comparison of Spot-Weld and Rivet Patterns in 24s-t Alclad and 75s-t Alclad

NASA Technical Reports Server (NTRS)

Russell, H W; Jackson, L R; Grover, H J; Beaver, W W

1944-01-01

Report contains detailed results of a number of fatigue tests on spot-welded joints in aluminum alloys. The tests described include: (1) fatigue tests on spot-welded lap joints in sheets of unequal thickness of alclad 24s-t. These tests indicate that the fatigue strength of a spot-welded joint in sheets of two different gages is slightly higher than that of a similar joint in two sheets of the thinner gage but definitely lower than that of a similar joint in two sheets of the thicker gage. (2) Fatigue tests on spot-welded alclad 75s-t spot-welded lap-joint specimens of alclad 75s-t were not any stronger in fatigue than similar specimens of alclad 24s-t. (3) Fatigue tests on lap-joint specimens spot -welded after various surface preparations--these included ac welding wire-brushed surfaces, dc welding wire-brushed surfaces, and dc welding chemically cleaned surfaces. While the ac welds were strongest statically, the dc welds on wire-brushed surfaces were strongest in fatigue. Specimens prepared in this way were very nearly as strong as the best riveted specimens tested for comparison. (4) Fatigue tests on specimens spot-welded with varying voltage so as to include a wide range of static spot-weld strengths. The fatigue strengths were in the same order as the static strengths but showed less range. (author)

Cell Sheet-Based Tissue Engineering for Organizing Anisotropic Tissue Constructs Produced Using Microfabricated Thermoresponsive Substrates.

PubMed

Takahashi, Hironobu; Okano, Teruo

2015-11-18

In some native tissues, appropriate microstructures, including orientation of the cell/extracellular matrix, provide specific mechanical and biological functions. For example, skeletal muscle is made of oriented myofibers that is responsible for the mechanical function. Native artery and myocardial tissues are organized three-dimensionally by stacking sheet-like tissues of aligned cells. Therefore, to construct any kind of complex tissue, the microstructures of cells such as myotubes, smooth muscle cells, and cardiomyocytes also need to be organized three-dimensionally just as in the native tissues of the body. Cell sheet-based tissue engineering allows the production of scaffold-free engineered tissues through a layer-by-layer construction technique. Recently, using microfabricated thermoresponsive substrates, aligned cells are being harvested as single continuous cell sheets. The cell sheets act as anisotropic tissue units to build three-dimensional tissue constructs with the appropriate anisotropy. This cell sheet-based technology is straightforward and has the potential to engineer a wide variety of complex tissues. In addition, due to the scaffold-free cell-dense environment, the physical and biological cell-cell interactions of these cell sheet constructs exhibit unique cell behaviors. These advantages will provide important clues to enable the production of well-organized tissues that closely mimic the structure and function of native tissues, required for the future of tissue engineering. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Process design of press hardening with gradient material property influence

NASA Astrophysics Data System (ADS)

Neugebauer, R.; Schieck, F.; Rautenstrauch, A.

2011-05-01

Press hardening is currently used in the production of automotive structures that require very high strength and controlled deformation during crash tests. Press hardening can achieve significant reductions of sheet thickness at constant strength and is therefore a promising technology for the production of lightweight and energy-efficient automobiles. The manganese-boron steel 22MnB5 have been implemented in sheet press hardening owing to their excellent hot formability, high hardenability, and good temperability even at low cooling rates. However, press-hardened components have shown poor ductility and cracking at relatively small strains. A possible solution to this problem is a selective increase of steel sheet ductility by press hardening process design in areas where the component is required to deform plastically during crash tests. To this end, process designers require information about microstructure and mechanical properties as a function of the wide spectrum of cooling rates and sequences and austenitizing treatment conditions that can be encountered in production environments. In the present work, a Continuous Cooling Transformation (CCT) diagram with corresponding material properties of sheet steel 22MnB5 was determined for a wide spectrum of cooling rates. Heating and cooling programs were conducted in a quenching dilatometer. Motivated by the importance of residual elasticity in crash test performance, this property was measured using a micro-bending test and the results were integrated into the CCT diagrams to complement the hardness testing results. This information is essential for the process design of press hardening of sheet components with gradient material properties.

Process design of press hardening with gradient material property influence

DOE Office of Scientific and Technical Information (OSTI.GOV)

Neugebauer, R.; Professorship for Machine Tools and Forming Technology, TU Chemnitz; Schieck, F.

Press hardening is currently used in the production of automotive structures that require very high strength and controlled deformation during crash tests. Press hardening can achieve significant reductions of sheet thickness at constant strength and is therefore a promising technology for the production of lightweight and energy-efficient automobiles. The manganese-boron steel 22MnB5 have been implemented in sheet press hardening owing to their excellent hot formability, high hardenability, and good temperability even at low cooling rates. However, press-hardened components have shown poor ductility and cracking at relatively small strains. A possible solution to this problem is a selective increase of steelmore » sheet ductility by press hardening process design in areas where the component is required to deform plastically during crash tests. To this end, process designers require information about microstructure and mechanical properties as a function of the wide spectrum of cooling rates and sequences and austenitizing treatment conditions that can be encountered in production environments. In the present work, a Continuous Cooling Transformation (CCT) diagram with corresponding material properties of sheet steel 22MnB5 was determined for a wide spectrum of cooling rates. Heating and cooling programs were conducted in a quenching dilatometer. Motivated by the importance of residual elasticity in crash test performance, this property was measured using a micro-bending test and the results were integrated into the CCT diagrams to complement the hardness testing results. This information is essential for the process design of press hardening of sheet components with gradient material properties.« less

3. ELEVATIONS, ADDITION TO POWER HOUSE. United Engineering Company Ltd., ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

3. ELEVATIONS, ADDITION TO POWER HOUSE. United Engineering Company Ltd., Alameda Shipyard. John Hudspeth, architect, foot of Main Street, Alameda, California. Sheet 4. Plan no. 10,548. Scale 1/4 inch to the foot, elevations, and one inch to the foot, sections and details. April 30, 1945, last revised 6/19/45. pencil on vellum - United Engineering Company Shipyard, Boiler House, 2900 Main Street, Alameda, Alameda County, CA

14. DREDGING MAP. United Engineering Company Ltd., Alameda Shipyard. Ship ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

14. DREDGING MAP. United Engineering Company Ltd., Alameda Shipyard. Ship repair facilities dredging map. No architect noted. Drawn by "J.H." (John Hudspeth?). Sheet 1. Plan no. 10,529. Scale one inch to 50 feet. September 22, 1943. U.S. Navy, Bureau of Yards & Docks, Contract no. bs 76. Approved for construction October 18, 1943. blueprint - United Engineering Company Shipyard, 2900 Main Street, Alameda, Alameda County, CA

ALTERATIONS AND ADDITIONS TO THE GATE HOUSE, United Engineering Company ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

ALTERATIONS AND ADDITIONS TO THE GATE HOUSE, United Engineering Company Ltd., Alameda Shipyard. Plan, elevations, and details of expanded structure. No architect noted. Drawn by "J.B.H." (John Hudspeth?). Sheet 2 of 2. Plan no. 10,504. Scale 1/4 inch to the foot. November 28, 1942, last revised 5/5/45. pencil on vellum - United Engineering Company Shipyard, Gate House, 2900 Main Street, Alameda, Alameda County, CA

Relation of structure to mechanical properties of thin thoria dispersion strengthened nickel-chromium (TD-NiCr alloy sheet

NASA Technical Reports Server (NTRS)

Whittenberger, J. D.

1975-01-01

A study of the relation between structure and mechanical properties of thin TD-NiCr sheet indicated that the elevated temperature tensile, stress-rupture, and creep strength properties depend primarily on the grain aspect ratio and sheet thickness. In general, the strength properties increased with increasing grain aspect ratio and sheet thickness. Tensile testing revealed an absence of ductility at elevated temperatures. A threshold stress for creep appears to exist. Even small amounts of prior creep deformation at elevated temperatures can produce severe creep damage.

Numerical analysis of the bucket surface roughness effects in Pelton turbine

NASA Astrophysics Data System (ADS)

Xiao, Y. X.; Zeng, C. J.; Zhang, J.; Yan, Z. G.; Wang, Z. W.

2013-12-01

The internal flow of a Pelton turbine is quite complex. It is difficult to analyse the unsteady free water sheet flow in the rotating bucket owing to the lack of a sound theory. Affected by manufacturing technique and silt abrasion during the operation, the bucket surface roughness of Pelton turbine may be too great, and thereby influence unit performance. To investigate the effect of bucket roughness on Pelton turbine performance, this paper presents the numerical simulation of the interaction between the jet and the bucket in a Pelton turbine. The unsteady three-dimensional numerical simulations were performed with CFX code by using the SST turbulence model coupling the two-phase flow volume of fluid method. Different magnitude orders of bucket surface roughness were analysed and compared. Unsteady numerical results of the free water sheet flow patterns on bucket surface, torque and unit performance for each bucket surface roughness were generated. The total pressure distribution on bucket surface is used to show the free water sheet flow pattern on bucket surface. By comparing the variation of water sheet flow patterns on bucket surface with different roughness, this paper qualitatively analyses how the bucket surface roughness magnitude influences the impeding effect on free water sheet flow. Comparison of the torque variation of different bucket surface roughness highlighted the effect of the bucket surface roughness on the Pelton turbine output capacity. To further investigate the effect of bucket surface roughness on Pelton turbine performance, the relation between the relative efficiency loss rate and bucket surface roughness magnitude is quantitatively analysed. The result can be used to predict and evaluate the Pelton turbine performance.

Durability improvements of two-dimensional metal nanoparticle sheets by molecular cross-linked structures between nanoparticles

NASA Astrophysics Data System (ADS)

Saito, Noboru; Ryuzaki, Sou; Wang, Pangpang; Park, Susie; Sakai, Nobuyuki; Tatsuma, Tetsu; Okamoto, Koichi; Tamada, Kaoru

2018-03-01

The durability of two-dimensional metal nanoparticle sheets is a crucial factor for realizing next-generation optoelectronic devices based on plasmonics such as organic light-emitting diodes. Here, we report improvements in the durability of Ag nanoparticle sheets by forming alkanedithiol (DT16) cross-linked structures between the nanoparticles. The cross-linked structures in a sheet were fabricated by the self-assembly of DT16-capped Ag nanoparticles with 10% coverage (AgDT16). The durabilities for thermal, organic solvent, and oxidation reactions of AgDT16 sheets were found to be improved owing to the cross-linked structures by comparing Ag nanoparticle sheets without the cross-linked structures. The absorbance spectra revealed that the Ag nanoparticle sheets without the structure are markedly damaged by each durability test, whereas the AgDT16 sheets remain. The molecular cross-linked structures between nanoparticles in two-dimansional metal nanoparticle sheets were found to have the potential to play a key role in the realization of plasmonic optoelectronic devices including metal nanoparticles.

Market Research on Law School Student Aid Award Letters and Shopping Sheet Information. NASFAA Consumer Information & Law Student Indebtedness Task Force Report

ERIC Educational Resources Information Center

National Association of Student Financial Aid Administrators, 2016

2016-01-01

"Market Research on Law School Student Aid Award Letters and Shopping Sheet Information" set out to identify through consumer testing what information on the financial aid award letter and U.S. Department of Education's (ED) Shopping Sheet could be modified to create a document that better assists students applying to, or currently…

Omega Hawaii Antenna System: Modification and Validation Tests. Volume 2. Data Sheets.

DTIC Science & Technology

1979-10-19

a benchmark because of potential hotel construction . DS 5-1 DATA SHEET 5 (DS-5) RADIO FIELD INTENSITY MEASUREMENTS OMEGA STATION: HAWAII SITE NO. C 1A...27.5 1008 11.05 26.5 1007 Ft 11.80 28.1 COMMENT Not considered for a benchmark because of potential hotel construction . DS 5-5 DATA SHEET 5 (DS-5) RADIO

Closure Report for Corrective Action Unit 329: Area 22 Desert Rock Airstrip Fuel Spill with Errata Sheet, Revision 0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Navarro Nevada Environmental Services

In Appendix 0, Use Restriction (UR) Form, the drawing of the use restricted area shows the incorrect coordinates for the use restricted area, the coordinates on the drawing do not match the approved UR Form. The coordinates have been verified and this Errata Sheet replaces the drawing of the use restricted area with an aerial photo showing the use restricted area and the correct coordinates that match the approved UR Form.

Critical Evaluation of State-of-the-Art In Situ Thermal Treatment Technologies for DNAPL Source Zone Treatment. State-of-the-Practice Overview

DTIC Science & Technology

2009-05-01

recovery in their design. Electrodes have been constructed from steel pipe , copper plate for heating distinct zones, and sheet pile. Sheet pile...energy transfer/ heating in the subsurface) The components required to implement ERH include: • Electrodes (steel pipe , copper plate, well points...including piping , blower, and condenser • A vapor treatment system Electrical Resistance Heating (Smith) A-3 • An ERH power control unit to

Intermodal freight transportation. Volume 2. Fact sheet, federal aid eligibility. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1995-12-01

The purpose of the Intermodal Freight Fact Sheet is to provide policymakers, planners, carriers, shippers and other interested parties with information that will create a better understanding of intermodal transportation and demonstrate the potential contribution of intermodalism to efficient freight transporation on the United States. This report on Federal Aid Eligibility examines support for facilities serving intermodal freight movements provided by Federal highway programs. Its purpose is to examine the expanding eligibility for Federal aid of intermodal freight projects.

Development of adapted GMR-probes for automated detection of hidden defects in thin steel sheets

NASA Astrophysics Data System (ADS)

Pelkner, Matthias; Pohl, Rainer; Kreutzbruck, Marc; Commandeur, Colin

2016-02-01

Thin steel sheets with a thickness of 0.3 mm and less are the base materials of many everyday life products (cans, batteries, etc.). Potential inhomogeneities such as non-metallic inclusions inside the steel can lead to a rupture of the sheets when it is formed into a product such as a beverage can. Therefore, there is a need to develop automated NDT techniques to detect hidden defects and inclusions in thin sheets during production. For this purpose Tata Steel Europe and BAM, the Federal Institute for Materials Research and Testing (Germany), collaborate in order to develop an automated NDT-system. Defect detection systems have to be robust against external influences, especially when used in an industrial environment. In addition, such a facility has to achieve a high sensitivity and a high spatial resolution in terms of detecting small inclusions in the μm-regime. In a first step, we carried out a feasibility study to determine which testing method is promising for detecting hidden defects and inclusions inside ferrous thin steel sheets. Therefore, two methods were investigated in more detail - magnetic flux leakage testing (MFL) using giant magneto resistance sensor arrays (GMR) as receivers [1,2] and eddy current testing (ET). The capabilities of both methods were tested with 0.2 mm-thick steel samples containing small defects with depths ranging from 5 µm up to 60 µm. Only in case of GMR-MFL-testing, we were able to detect parts of the hidden defects with a depth of 10 µm trustworthily with a SNR better than 10 dB. Here, the lift off between sensor and surface was 250 µm. On this basis, we investigated different testing scenarios including velocity tests and different lift offs. In this contribution we present the results of the feasibility study leading to first prototypes of GMR-probes which are now installed as part of a demonstrator inside a production line.

Method and apparatus for determining weldability of thin sheet metal

DOEpatents

Goodwin, Gene M.; Hudson, Joseph D.

1988-01-01

A fixture is provided for testing thin sheet metal specimens to evaluate hot-cracking sensitivity for determining metal weldability on a heat-to-heat basis or through varying welding parameters. A test specimen is stressed in a first direction with a load selectively adjustable over a wide range and then a weldment is passed along over the specimen in a direction transverse to the direction of strain to evaluate the hot-cracking characteristics of the sheet metal which are indicative of the weldability of the metal. The fixture provides evaluations of hot-cracking sensitivity for determining metal weldability in a highly reproducible manner with minimum human error.

Numerical study of the current sheet and PSBL in a magnetotail model

NASA Technical Reports Server (NTRS)

Doxas, I.; Horton, W.; Sandusky, K.; Tajima, T.; Steinolfson, R.

1989-01-01

The current sheet and plasma sheet boundary layer (PSBL) in a magnetotail model are discussed. A test particle code is used to study the response of ensembles of particles to a two-dimensional, time-dependent model of the geomagnetic tail, and test the proposition (Coroniti, 1985a, b; Buchner and Zelenyi, 1986; Chen and Palmadesso, 1986; Martin, 1986) that the stochasticity of the particle orbits in these fields is an important part of the physical mechanism for magnetospheric substorms. The realistic results obtained for the fluid moments of the particle distribution with this simple model, and their insensitivity to initial conditions, is consistent with this hypothesis.

Atomically thin two-dimensional organic-inorganic hybrid perovskites

NASA Astrophysics Data System (ADS)

Dou, Letian; Wong, Andrew B.; Yu, Yi; Lai, Minliang; Kornienko, Nikolay; Eaton, Samuel W.; Fu, Anthony; Bischak, Connor G.; Ma, Jie; Ding, Tina; Ginsberg, Naomi S.; Wang, Lin-Wang; Alivisatos, A. Paul; Yang, Peidong

2015-09-01

Organic-inorganic hybrid perovskites, which have proved to be promising semiconductor materials for photovoltaic applications, have been made into atomically thin two-dimensional (2D) sheets. We report the solution-phase growth of single- and few-unit-cell-thick single-crystalline 2D hybrid perovskites of (C4H9NH3)2PbBr4 with well-defined square shape and large size. In contrast to other 2D materials, the hybrid perovskite sheets exhibit an unusual structural relaxation, and this structural change leads to a band gap shift as compared to the bulk crystal. The high-quality 2D crystals exhibit efficient photoluminescence, and color tuning could be achieved by changing sheet thickness as well as composition via the synthesis of related materials.

EnviroAtlas - Historic Places by 12-digit HUC for the Conterminous United States

EPA Pesticide Factsheets

This EnviroAtlas dataset portrays the total number of historic places located within each 12-digit Hydrologic Unit (HUC). The historic places data were compiled from the National Park Service's National Register of Historic Places (NRHP), which provides official federal lists of districts, sites, buildings, structures and objects significant to American history, architecture, archeology, engineering, and culture. This dataset was produced by the US EPA to support research and online mapping activities related to EnviroAtlas. EnviroAtlas (https://www.epa.gov/enviroatlas) allows the user to interact with a web-based, easy-to-use, mapping application to view and analyze multiple ecosystem services for the contiguous United States. The dataset is available as downloadable data (https://edg.epa.gov/data/Public/ORD/EnviroAtlas) or as an EnviroAtlas map service. Additional descriptive information about each attribute in this dataset can be found in its associated EnviroAtlas Fact Sheet (https://www.epa.gov/enviroatlas/enviroatlas-fact-sheets).

The Steady Flow Resistance of Perforated Sheet Materials in High Speed Grazing Flows

NASA Technical Reports Server (NTRS)

Syed, Asif A.; Yu, Jia; Kwan, H. W.; Chien, E.; Jones, Michael G. (Technical Monitor)

2002-01-01

A study was conducted to determine the effects of high speed grazing air flow on the acoustic resistance of perforated sheet materials used in the construction of acoustically absorptive liners placed in commercial aircraft engine nacelles. Since DC flow resistance of porous sheet materials is known to be a major component of the acoustic resistance of sound suppression liners, the DC flow resistance of a set of perforated face-sheets and linear 'wiremesh' face-sheets was measured in a flow duct apparatus (up to Mach 0.8). Samples were fabricated to cover typical variations in perforated face-sheet parameters, such as hole diameter, porosity and sheet thickness, as well as those due to different manufacturing processes. The DC flow resistance data from perforated sheets were found to correlate strongly with the grazing flow Mach number and the face-sheet porosity. The data also show correlation against the boundary layer displacement thickness to hole-diameter ratio. The increase in resistance with grazing flow for punched aluminum sheets is in good agreement with published results up to Mach 0.4, but is significantly larger than expected above Mach 0.4. Finally, the tests demonstrated that there is a significant increase in the resistance of linear 'wiremesh' type face-sheet materials.

Conformation and Dynamics of a Flexible Sheet in Solvent Media by Monte Carlo Simulations

NASA Astrophysics Data System (ADS)

Pandey, Ras; Anderson, Kelly; Heinz, Hendrik; Farmer, Barry

2005-03-01

Flexibility of the clay sheet is limited even in the ex-foliated state in some solvent media. A coarse grained model is used to investigate dynamics and conformation of a flexible sheet to model such a clay platelet in an effective solvent medium on a cubic lattice of size L^3 with lattice constant a. The undeformed sheet is described by a square lattice of size Ls^2, where, each node of the sheet is represented by the unit cube of the cubic lattice and 2a is the minimum distance between the nearest neighbor nodes to incorporate the excluded volume constraints. Additionally, each node interacts with neighboring nodes and solvent (empty) sites within a range ri. Each node execute their stochastic motion with the Metropolis algorithm subject to bond length fluctuation and excluded volume constraints. Mean square displacements of the center node and that of its center of mass are investigated as a function of time step for a set of these parameters. The radius of gyration (Rg) is also examined concurrently to understand its relaxation. Multi-scale segmental dynamics of the sheet is studied by identifying the power-law dependence in various time regimes. Relaxation of Rg and its dependence of temperature are planned to be discussed.

A review and assessment of Virginia's license plate sheeting specifications.

DOT National Transportation Integrated Search

2003-01-01

At the request of Virginia's Secretary of Transportation, the Virginia Transportation Research Council undertook a review and assessment of Virginia's license plate sheeting specifications. The review was focused on the five test methods or specifica...

Semen Analysis

MedlinePlus

... Booklets Pruebas diagnósticas para la infertilidad masculina (Diagnostic tests for male infertility) From: Spanish Fact Sheets & Info Booklets Assisted reproductive technology 辅助生殖技术辅助生殖技术 From: Chinese Fact Sheets & Info Booklets Diagnostic ...

Youth Homicide and Guns. Firearm Facts.

ERIC Educational Resources Information Center

Duker, Laurie, Ed.

Young Americans are killed with guns at rates far higher than young people in other countries and than older Americans, with young, urban African-American males being most at risk. This fact sheet presents data on gun-related homicides among teenagers in the United States. The high rate of youth homicide in the United States is unique in the…

Kids Count Data Sheet, 2000.

ERIC Educational Resources Information Center

Annie E. Casey Foundation, Baltimore, MD.

Data from the 50 United States are listed for 1997 from Kids Count in an effort to track state-by-state the status of children in the United States and to secure better futures for all children. Data include percent low birth weight babies; infant mortality rate; child death rate; rate of teen deaths by accident, homicide, and suicide; teen birth…

76 FR 9542 - Stainless Steel Sheet and Strip in Coils From Mexico; Notice of Amended Final Results of...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-18

... investigation; and (4) the cash deposit rate for all non-Mexican exporters will be the rate applicable to the...-unit cost of production and per-unit packing expenses by the quantity sold. See Mexinox Ministerial.... indirect selling expenses. Specifically, Mexinox contends that the Department a) failed to include ``other...

Cecil Cereal's Supermarket Search. Teacher's Guide [and] Student Materials.

ERIC Educational Resources Information Center

Estes, Cynthia

The document presents objectives, teaching methods, activities, and work sheets for a unit on choosing breakfast cereal. The unit is intended to be used as an integral part of the fifth grade health program. Activities take place in a classroom learning center and can be completed in approximately four to six hours of classroom time. Objectives…

Investigation to Identify Performance Criteria and Test Methods for Evaluating Single-Ply Roofing Systems.

DTIC Science & Technology

1987-03-01

Reinforced Black EPDM Rubber Sheets for Use in Roofing Applications ( Rubber Manufacturers Association [RMAJ, 1984). Minimum Requirements for Fabric-Reinforced...Black Polychloroprene Rubber Sheets for Use in Roofing Applications (RMA, 1984). Minimum Requirements for Non-Reinforced Black EPDM Rubber Sheets for...and materials. The Rubber Manufacturers Amoeiation (RMA) (USA) RMA is funding a study in conjunction with ASTM to evaluate three different EPDM

3D Printing of Thermo-Responsive Methylcellulose Hydrogels for Cell-Sheet Engineering

PubMed Central

Cochis, Andrea; Sorrentino, Rita; Grassi, Federico; Leigheb, Massimiliano; Farè, Silvia

2018-01-01

A possible strategy in regenerative medicine is cell-sheet engineering (CSE), i.e., developing smart cell culture surfaces from which to obtain intact cell sheets (CS). The main goal of this study was to develop 3D printing via extrusion-based bioprinting of methylcellulose (MC)-based hydrogels. Hydrogels were prepared by mixing MC powder in saline solutions (Na2SO4 and PBS). MC-based hydrogels were analyzed to investigate the rheological behavior and thus optimize the printing process parameters. Cells were tested in vitro on ring-shaped printed hydrogels; bulk MC hydrogels were used for comparison. In vitro tests used murine embryonic fibroblasts (NIH/3T3) and endothelial murine cells (MS1), and the resulting cell sheets were characterized analyzing cell viability and immunofluorescence. In terms of CS preparation, 3D printing proved to be an optimal approach to obtain ring-shaped CS. Cell orientation was observed for the ring-shaped CS and was confirmed by the degree of circularity of their nuclei: cell nuclei in ring-shaped CS were more elongated than those in sheets detached from bulk hydrogels. The 3D printing process appears adequate for the preparation of cell sheets of different shapes for the regeneration of complex tissues. PMID:29642573

Boosting protein stability with the computational design of β-sheet surfaces.

PubMed

Kim, Doo Nam; Jacobs, Timothy M; Kuhlman, Brian

2016-03-01

β-sheets often have one face packed against the core of the protein and the other facing solvent. Mutational studies have indicated that the solvent-facing residues can contribute significantly to protein stability, and that the preferred amino acid at each sequence position is dependent on the precise structure of the protein backbone and the identity of the neighboring amino acids. This suggests that the most advantageous methods for designing β-sheet surfaces will be approaches that take into account the multiple energetic factors at play including side chain rotamer preferences, van der Waals forces, electrostatics, and desolvation effects. Here, we show that the protein design software Rosetta, which models these energetic factors, can be used to dramatically increase protein stability by optimizing interactions on the surfaces of small β-sheet proteins. Two design variants of the β-sandwich protein from tenascin were made with 7 and 14 mutations respectively on its β-sheet surfaces. These changes raised the thermal midpoint for unfolding from 45°C to 64°C and 74°C. Additionally, we tested an empirical approach based on increasing the number of potential salt bridges on the surfaces of the β-sheets. This was not a robust strategy for increasing stability, as three of the four variants tested were unfolded. © 2016 The Protein Society.

Hecules Fact Sheet.EPA.May 2011.final

EPA Pesticide Factsheets

EPA Region 4 fact sheet from May 2011 about a 3013 order to Hercules, Inc. in Hattiesburg, MS to conduct on- and off-site monitoring, testing, and reporting the nature and extent of any environmental contamination at their facility.

Environmental Technology Verification Program Fact Sheet

EPA Science Inventory

This is a Fact Sheet for the ETV Program. The EPA Environmental Technology Verification Program (ETV) develops test protocols and verifies the performance of innovative technologies that have the potential to improve protection of human health and the environment. The program ...

Free Wake Techniques for Rotor Aerodynamic Analylis. Volume 2: Vortex Sheet Models

NASA Technical Reports Server (NTRS)

Tanuwidjaja, A.

1982-01-01

Results of computations are presented using vortex sheets to model the wake and test the sensitivity of the solutions to various assumptions used in the development of the models. The complete codings are included.

Integration of new geologic mapping and satellite-derived quartz mapping yields insights into the structure of the Roberts Mountains allochthon applicable to assessments for concealed Carlin-type gold deposits

USGS Publications Warehouse

Holm-Denoma, Christopher S.; Hofstra, Albert H.; Rockwell, Barnaby W.; Noble, Paula J.

2012-01-01

Geologic mapping and remote sensing across north-central Nevada enable recognition of a thick sheet of Middle and Upper Ordovician Valmy Formation quartzite that structurally overlies folded and faulted Ordovician through Devonian stratigraphic units of the Roberts Mountains allochthon. In the northern Independence Mountains and nearby Double Mountain area, the Valmy Formation is in fault contact with Ordovician through Silurian, predominantly clastic, sedimentary rocks of the Roberts Mountains allochthon that were deformed prior to, or during, emplacement of the Valmy thrust sheet. Similar structural relations are recognized discontinuously for 200 kilometers along the strike of the Roberts Mountains allochthon in mapping guided by regional remote-sensing-based (ASTER) quartz maps. Overall thicknesses of deformed Roberts Mountains allochthon units between the base of the Valmy and the top of underlying carbonate rocks that host large Carlin-type gold deposits varies on the order of hundreds of meters but is not known to exceed 700 meters. The base of the Valmy thrust sheet is a complimentary datum in natural resource exploration and mineral resource assessment for concealed Carlin-type gold deposits.

Pesticide Information Sources in the United States.

ERIC Educational Resources Information Center

Alston, Patricia Gayle

1992-01-01

Presents an overview of electronic and published sources on pesticides. Includes sources such as databases, CD-ROMs, books, journals, brochures, pamphlets, fact sheets, hotlines, courses, electronic mail, and electronic bulletin boards. (MCO)

Detection of Steel Fatigue Cracks with Strain Sensing Sheets Based on Large Area Electronics

PubMed Central

Yao, Yao; Glisic, Branko

2015-01-01

Reliable early-stage damage detection requires continuous monitoring over large areas of structure, and with sensors of high spatial resolution. Technologies based on Large Area Electronics (LAE) can enable direct sensing and can be scaled to the level required for Structural Health Monitoring (SHM) of civil structures and infrastructure. Sensing sheets based on LAE contain dense arrangements of thin-film strain sensors, associated electronics and various control circuits deposited and integrated on a flexible polyimide substrate that can cover large areas of structures. This paper presents the development stage of a prototype strain sensing sheet based on LAE for crack detection and localization. Two types of sensing-sheet arrangements with size 6 × 6 inch (152 × 152 mm) were designed and manufactured, one with a very dense arrangement of sensors and the other with a less dense arrangement of sensors. The sensing sheets were bonded to steel plates, which had a notch on the boundary, so the fatigue cracks could be generated under cyclic loading. The sensors within the sensing sheet that were close to the notch tip successfully detected the initialization of fatigue crack and localized the damage on the plate. The sensors that were away from the crack successfully detected the propagation of fatigue cracks based on the time history of the measured strain. The results of the tests have validated the general principles of the proposed sensing sheets for crack detection and identified advantages and challenges of the two tested designs. PMID:25853407

Role of oxygen functional groups in reduced graphene oxide for lubrication

PubMed Central

Gupta, Bhavana; Kumar, Niranjan; Panda, Kalpataru; Kanan, Vigneshwaran; Joshi, Shailesh; Visoly-Fisher, Iris

2017-01-01

Functionalized and fully characterized graphene-based lubricant additives are potential 2D materials for energy-efficient tribological applications in machine elements, especially at macroscopic contacts. Two different reduced graphene oxide (rGO) derivatives, terminated by hydroxyl and epoxy-hydroxyl groups, were prepared and blended with two different molecular weights of polyethylene glycol (PEG) for tribological investigation. Epoxy-hydroxyl-terminated rGO dispersed in PEG showed significantly smaller values of the friction coefficient. In this condition, PEG chains intercalate between the functionalized graphene sheets, and shear can take place between the PEG and rGO sheets. However, the friction coefficient was unaffected when hydroxyl-terminated rGO was coupled with PEG. This can be explained by the strong coupling between graphene sheets through hydroxyl units, causing the interaction of PEG with the rGO to be non- effective for lubrication. On the other hand, antiwear properties of hydroxyl-terminated rGO were significantly enhanced compared to epoxy-hydroxyl functionalized rGO due to the integrity of graphene sheet clusters. PMID:28344337

Correlation of ash-flow tuffs.

USGS Publications Warehouse

Hildreth, W.; Mahood, G.

1985-01-01

Discrimination and correlation of ash-flow sheets is important in structurally complex, long-lived volcanic fields where such sheets provide the best keys to the regional stratigraphic framework. Three-dimensional complexities resulting from pulsatory eruptions, sectorial emplacement, mechanical sorting during outflow, thermal and compositional zoning of magmas, the physical zoning of cooling units, and structural and erosional disruption can make such correlation and discrimination difficult. When lithologic, magnetic, petrographic, chemical, and isotopic criteria for correlating ash-flow sheets are critically evaluated, many problems and pitfalls can be identified. Distinctive phenocrysts, pumice clasts, and lithic fragments are among the more reliable criteria, as are high-precision K-Ar ages and thermal remanent magnetization (TRM) directions in unaltered welded tuff. Chemical correlation methods should rely principally upon welded or nonwelded pumice blocks, not upon the ash-flow matrix, which is subject to fractionation, mixing, and contamination during emplacement. Compositional zoning of most large sheets requires that many samples be analyzed before phenocryst, glass or whole-rock chemical trends can be used confidently as correlation criteria.-Authors

Design and preparation of beta-sheet forming repetitive and block-copolymerized polypeptides.

PubMed

Higashiya, Seiichiro; Topilina, Natalya I; Ngo, Silvana C; Zagorevskii, Dmitri; Welch, John T

2007-05-01

The design and rapid construction of libraries of genes coding beta-sheet forming repetitive and block-copolymerized polypeptides bearing various C- and N-terminal sequences are described. The design was based on the assembly of DNA cassettes coding for the (GA)3GX amino acid sequence where the (GAGAGA) sequences would constitute the beta-strand units of a larger beta-sheet assembly. The edges of this beta-sheet would be functionalized by the turn-inducing amino acids (GX). The polypeptides were expressed in Escherichia coli using conventional vectors and were purified by Ni-nitriloacetic acid (NTA) chromatography. The correlation of polymer structure with molecular weight was investigated by gel electrophoresis and mass spectrometry. The monomer sequences and post-translational chemical modifications were found to influence the mobility of the polypeptides over the full range of polypeptide molecular weights while the electrophoretic mobility of lower molecular weight polypeptides was more susceptible to C- and N-termini polypeptide modifications.

A laser-sheet flow visualization technique for the large wind tunnels of the National Full-Scale Aerodynamics Complex

NASA Technical Reports Server (NTRS)

Reinath, M. S.; Ross, J. C.

1990-01-01

A flow visualization technique for the large wind tunnels of the National Full Scale Aerodynamics Complex (NFAC) is described. The technique uses a laser sheet generated by the NFAC Long Range Laser Velocimeter (LRLV) to illuminate a smoke-like tracer in the flow. The LRLV optical system is modified slightly, and a scanned mirror is added to generate the sheet. These modifications are described, in addition to the results of an initial performance test conducted in the 80- by 120-Foot Wind Tunnel. During this test, flow visualization was performed in the wake region behind a truck as part of a vehicle drag reduction study. The problems encountered during the test are discussed, in addition to the recommended improvements needed to enhance the performance of the technique for future applications.

Results of the Greenland ice sheet model initialisation experiments: ISMIP6 - initMIP-Greenland

NASA Astrophysics Data System (ADS)

Goelzer, Heiko; Nowicki, Sophie; Edwards, Tamsin; Beckley, Matthew

2017-04-01

Ice sheet model initialisation has a large effect on projected future sea-level contributions and gives rise to important uncertainties. The goal of this intercomparison exercise for the continental-scale Greenland ice sheet is therefore to compare, evaluate and improve the initialisation techniques used in the ice sheet modelling community. The initMIP-Greenland project is the first in a series of ice sheet model intercomparison activities within ISMIP6 (Ice Sheet Model Intercomparison Project for CMIP6). The experimental set-up has been designed to allow comparison of the initial present-day state of the Greenland ice sheet between participating models and against observations. Furthermore, the initial states are tested with two schematic forward experiments to evaluate the initialisation in terms of model drift (forward run without any forcing) and response to a large perturbation (prescribed surface mass balance anomaly). We present and discuss results that highlight the wide diversity of data sets, boundary conditions and initialisation techniques used in the community to generate initial states of the Greenland ice sheet.

Thermal properties of highly structured composite and aluminium sheets in an aerodynamic tunnel

NASA Astrophysics Data System (ADS)

Kulhavy, Petr; Egert, Josef

This article deals with the thermodynamic behaviour of heat shields - structured metal and composite plates. Experiments have been carried out in a wind tunnel with an additional heating, which simulates the heat source from engine or exhaust pipe and simultaneously the airflow generated during a car movement. The tested sheets with hexagonal structure were a standard commercial made of aluminium and a second manufactured by replication (lamination, diffusion) from glass fabric. The airflow in a parallel way along the sheets was analysed experimentally in order to determine the heat transfer efficiency between surfaces of sheets and surrounding airflow. The temperature on the sheets was chosen to observe the effects of different sheets material, various heat power and airflow velocity. During the experiment a thermal input below the sheets and airflow velocity through the tunnel have been changed. The thermal field distribution on the metal sheet is different than in case of composite sheet. For the composite material the thermal field distribution was more homogeneous. This article describe briefly also methods of obtaining real composite geometry based on scanned data and their reconstruction for using in some future numerical models.

Subscale Water Based Phase Change Material Heat Exchanger Development

NASA Technical Reports Server (NTRS)

Sheth, Rubik; Hansen, Scott

2016-01-01

Supplemental heat rejection devices are required in many spacecraft as the radiators are not sized to meet the full heat rejection demand. One means of obtaining additional heat rejection is through the use of phase change material heat exchangers (PCM HX's). PCM HX's utilize phase change to store energy in unfavorable thermal environments (melting) and reject the energy in favorable environments (freezing). Traditionally, wax has been used as a PCM on spacecraft. However, water is an attractive alternative because it is capable of storing about 40% more energy per unit mass due to its higher latent heat of fusion. The significant problem in using water as a PCM is its expansion while freezing, leading to structural integrity concerns when housed in an enclosed heat exchanger volume. Significant investigation and development has taken place over the past five years to understand and overcome the problems associated with water PCM HX's. This paper reports on the final efforts by Johnson Space Center's Thermal Systems Branch to develop a water based PCM HX. The test article developed and reported on is a subscale version of the full-scale water-based PCM HX's constructed by Mezzo Technologies. The subscale unit was designed by applying prior research on freeze front propagation and previous full-scale water PCM HX development. Design modifications to the subscale unit included use of urethane bladder, decreased aspect ratio, perforated protection sheet, and use of additional mid-plates. Testing of the subscale unit was successful and 150 cycles were completed without fail.

Ductile Tearing Resistance Indexing of Automotive Grade DP 590 Steel Sheets: EWF Testing Using DENT Specimens

NASA Astrophysics Data System (ADS)

Sahoo, Subhadra; Padmapriya, N.; De, Partha Sarathi; Chakraborti, P. C.; Ray, S. K.

2018-03-01

The essential work of fracture (EWF) method has been explored for indexing the ductile tearing resistance of DP 590 automotive grade dual-phase steel sheet both in longitudinal (L-T) and transverse (T-L) orientations. The simplest possible test and analysis procedures have been adopted. The EWF method is found to be eminently suitable for routine quality control and product development purposes for such materials. Areas for further research for improving the experimental strategy are highlighted. For the investigated steel sheet, the estimated tearing resistance is found to be distinctly higher for the L-T orientation compared to the T-L orientation; the reason thereof merits further investigation.

Alternative plasticizer, 4-cyclohexene-1,2-dicarboxylic acid dinonyl ester, for blood containers with protective effects on red blood cells and improved cold resistance.

PubMed

Morishita, Yuki; Nomura, Yusuke; Fukui, Chie; Fujisawa, Ayano; Watanabe, Kayo; Fujimaki, Hideo; Kumada, Hidefumi; Inoue, Kaoru; Morikawa, Tomomi; Takahashi, Miwa; Kawakami, Tsuyoshi; Sakoda, Hideyuki; Mukai, Tomokazu; Yuba, Toshiyasu; Inamura, Ken-Ichi; Tanoue, Akito; Miyazaki, Ken-Ichi; Chung, Ung-Il; Ogawa, Kumiko; Yoshida, Midori; Haishima, Yuji

2018-04-01

Di (2-ethylhexyl) phthalate (DEHP), a typical plasticizer used for polyvinyl chloride (PVC), is eluted from PVC-made blood containers and protects against red blood cell (RBC) hemolysis. However, concerns have arisen regarding the reproductive and developmental risks of DEHP in humans, and the use of alternative plasticizers for medical devices has been recommended worldwide. In this study, we propose that the use of a novel plasticizer, 4-cyclohexene-1,2-dicarboxylic acid dinonyl ester (DL9TH), could help produce more useful and safe blood containers. PVC sheet containing DL9TH and di (2-ethylhexyl) 4-cyclohexene-1,2-dicarboxylate (DOTH) provides comparable or superior protective effects to RBCs relative to PVC sheet containing DEHP or di-isononyl-cyclohexane-1,2-dicarboxylate (DINCH ® , an alternative plasticizer that has been used in PVC sheets for blood containers). The total amount of plasticizer eluted from DOTH/DL9TH-PVC sheets is nearly the same as that eluted from DEHP-PVC sheets. In addition, DOTH/DL9TH-PVC has better cold resistance than DEHP- and DINCH ® -PVC sheets. In vitro and in vivo tests for biological safety based on International Organization for Standardization guidelines (10993 series) suggest that the DOTH/DL9TH-PVC sheet can be used safely. Subchronic toxicity testing of DL9TH in male rats in accordance with the principles of Organisation for Economic Co-operation and Development Test Guideline 408 showed that DL9TH did not induce adverse effects up to the highest dose level tested (717 mg/kg body weight/day). There were no effects on testicular histopathology and sperm counts, and no indications of endocrine effects: testosterone, thyroid-stimulating hormone, follicle-stimulating hormone, and 17β-estradiol were unchanged by the treatment, compared with the control group. © 2017 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 106B: 1052-1063, 2018. © 2017 Wiley Periodicals, Inc.

A Cost-Effective Transparency-Based Digital Imaging for Efficient and Accurate Wound Area Measurement

PubMed Central

Li, Pei-Nan; Li, Hong; Wu, Mo-Li; Wang, Shou-Yu; Kong, Qing-You; Zhang, Zhen; Sun, Yuan; Liu, Jia; Lv, De-Cheng

2012-01-01

Wound measurement is an objective and direct way to trace the course of wound healing and to evaluate therapeutic efficacy. Nevertheless, the accuracy and efficiency of the current measurement methods need to be improved. Taking the advantages of reliability of transparency tracing and the accuracy of computer-aided digital imaging, a transparency-based digital imaging approach is established, by which data from 340 wound tracing were collected from 6 experimental groups (8 rats/group) at 8 experimental time points (Day 1, 3, 5, 7, 10, 12, 14 and 16) and orderly archived onto a transparency model sheet. This sheet was scanned and its image was saved in JPG form. Since a set of standard area units from 1 mm2 to 1 cm2 was integrated into the sheet, the tracing areas in JPG image were measured directly, using the “Magnetic lasso tool” in Adobe Photoshop program. The pixel values/PVs of individual outlined regions were obtained and recorded in an average speed of 27 second/region. All PV data were saved in an excel form and their corresponding areas were calculated simultaneously by the formula of Y (PV of the outlined region)/X (PV of standard area unit) × Z (area of standard unit). It took a researcher less than 3 hours to finish area calculation of 340 regions. In contrast, over 3 hours were expended by three skillful researchers to accomplish the above work with traditional transparency-based method. Moreover, unlike the results obtained traditionally, little variation was found among the data calculated by different persons and the standard area units in different sizes and shapes. Given its accurate, reproductive and efficient properties, this transparency-based digital imaging approach would be of significant values in basic wound healing research and clinical practice. PMID:22666449

Report to Lincoln Labs on TWPAs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dubois, J.; Carosi, G.; Woollett, N.

2017-09-26

This past spring LLNL’s Quantum Sensor’s team received two TWPA amplifiers from Lincoln Labs along with a data-sheet explaining handling, operations and expected performance. Here we will outline some of the initial tests performed on this amplifiers as part of LLNL’s Quantum Sensors Strategic Initiative (QSSI). Initial testing confirmed that both amplifiers worked and provided gain and SNR improvement similar to that called out in the data-sheets provided.

Elastic behavior and onset of cracking in cement composite plates reinforced by perforated thin steel sheets

NASA Astrophysics Data System (ADS)

Aronchik, V.

1996-03-01

Thin cement mortar plates reinforced by perforated thin steel sheets have been tested in four-point flexure loading. Six kinds of sheet reinforcement and to additional ones (for control) were used. Perforated sheets of the Daugavpils Factory of Machinery Chains differed by their thickness (0.6-1.8 mm), shape (round, rectangular, oval, "dumbbell"), and mark of steel (St. 08, 50, 70). Dimensions of plantes were 100×20×2 cm. Cements-sand mortar with a 1∶2 ratio of cement PZ35 and river sand of 3 mm grains was used as a matrix. Control specimens of similar dimensions and matrix were reinforced by wire cages and meshes (ferrocement). The testing was performed using an UMM-5 testing machine. Maximum deflection (at the midspan), tension, and shear strains were recorded. The expeimental data are presented in tables and graphs. The testing results showed that the elasticity modulus of material was in good agreement with the "admixture rule;" an onset of cracking for all types (excluding one) practically did not differ from reference samples; the mode of fracture in typical cases included an adhesion failure and significant shear strains. In one case the limit of the tension strength of the reinforcement was achieved.

HAER COLO,30LAKWD.V,2G (sheet 1 of 1) Glenn L. Martin ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

HAER COLO,30-LAKWD.V,2G- (sheet 1 of 1) - Glenn L. Martin Company, Titan Missile Test Facilities, Cold Flow Laboratory Building B, Waterton Canyon Road & Colorado Highway 121, Lakewood, Jefferson County, CO

Using genetic algorithm to determine the optimal order quantities for multi-item multi-period under warehouse capacity constraints in kitchenware manufacturing

NASA Astrophysics Data System (ADS)

Saraswati, D.; Sari, D. K.; Johan, V.

2017-11-01

The study was conducted on a manufacturer that produced various kinds of kitchenware with kitchen sink as the main product. There were four types of steel sheets selected as the raw materials of the kitchen sink. The problem was the manufacturer wanted to determine how much steel sheets to order from a single supplier to meet the production requirements in a way to minimize the total inventory cost. In this case, the economic order quantity (EOQ) model was developed using all-unit discount as the price of steel sheets and the warehouse capacity was limited. Genetic algorithm (GA) was used to find the minimum of the total inventory cost as a sum of purchasing cost, ordering cost, holding cost and penalty cost.

Atomically thin two-dimensional organic-inorganic hybrid perovskites.

PubMed

Dou, Letian; Wong, Andrew B; Yu, Yi; Lai, Minliang; Kornienko, Nikolay; Eaton, Samuel W; Fu, Anthony; Bischak, Connor G; Ma, Jie; Ding, Tina; Ginsberg, Naomi S; Wang, Lin-Wang; Alivisatos, A Paul; Yang, Peidong

2015-09-25

Organic-inorganic hybrid perovskites, which have proved to be promising semiconductor materials for photovoltaic applications, have been made into atomically thin two-dimensional (2D) sheets. We report the solution-phase growth of single- and few-unit-cell-thick single-crystalline 2D hybrid perovskites of (C4H9NH3)2PbBr4 with well-defined square shape and large size. In contrast to other 2D materials, the hybrid perovskite sheets exhibit an unusual structural relaxation, and this structural change leads to a band gap shift as compared to the bulk crystal. The high-quality 2D crystals exhibit efficient photoluminescence, and color tuning could be achieved by changing sheet thickness as well as composition via the synthesis of related materials. Copyright © 2015, American Association for the Advancement of Science.

EnviroAtlas National Layers Master Web Service

EPA Pesticide Factsheets

This EnviroAtlas web service supports research and online mapping activities related to EnviroAtlas (https://www.epa.gov/enviroatlas). This web service includes layers depicting EnviroAtlas national metrics mapped at the 12-digit HUC within the conterminous United States. This dataset was produced by the US EPA to support research and online mapping activities related to EnviroAtlas. EnviroAtlas (https://www.epa.gov/enviroatlas) allows the user to interact with a web-based, easy-to-use, mapping application to view and analyze multiple ecosystem services for the contiguous United States. The dataset is available as downloadable data (https://edg.epa.gov/data/Public/ORD/EnviroAtlas) or as an EnviroAtlas map service. Additional descriptive information about each attribute in this dataset can be found in its associated EnviroAtlas Fact Sheet (https://www.epa.gov/enviroatlas/enviroatlas-fact-sheets).

Bedrock geologic map of the Seward Peninsula, Alaska, and accompanying conodont data

USGS Publications Warehouse

Till, Alison B.; Dumoulin, Julie A.; Werdon, Melanie B.; Bleick, Heather A.

2011-01-01

This 1:500,000-scale geologic map depicts the bedrock geology of Seward Peninsula, western Alaska, on the North American side of the Bering Strait. The map encompasses all of the Teller, Nome, Solomon, and Bendeleben 1:250,000-scale quadrangles, and parts of the Shishmaref, Kotzebue, Candle, and Norton Bay 1:250,000-scale quadrangles (sh. 1; sh. 2). The geologic map is presented on Sheet 1. The pamphlet includes an introductory text, detailed unit descriptions, tables of geochronologic data, and an appendix containing conodont (microfossil) data and a text explaining those data. Sheet 2 shows metamorphic and tectonic units, conodont color alteration indices, key metamorphic minerals, and locations of geochronology samples listed in the pamphlet. The map area covers 74,000 km2, an area slightly larger than West Virginia or Ireland.

Pleistocene hydrology of North America: The role of ice sheets in reorganizing groundwater flow systems

NASA Astrophysics Data System (ADS)

Person, Mark; McIntosh, Jennifer; Bense, Victor; Remenda, V. H.

2007-09-01

While the geomorphic consequences of Pleistocene megafloods have been known for some time, it has been only in the past 2 decades that hydrogeologists and glaciologists alike have begun to appreciate the important impact that ice sheet-aquifer interactions have had in controlling subsurface flow patterns, recharge rates, and the distribution of fresh water in confined aquifer systems across North America. In this paper, we document the numerous lines of geochemical, isotopic, and geomechanical evidence of ice sheet hydrogeology across North America. We also review the mechanical, thermal, and hydrologic processes that control subsurface fluid migration beneath ice sheets. Finite element models of subsurface fluid flow, permafrost formation, and ice sheet loading are presented to investigate the coupled nature of transport processes during glaciation/deglaciation. These indicate that recharge rates as high as 10 times modern values occurred as the Laurentide Ice Sheet overran the margins of sedimentary basins. The effects of ice sheet loading and permafrost formation result in complex transient flow patterns within aquifers and confining units alike. Using geochemical and environmental isotopic data, we estimate that the volume of glacial meltwater emplaced at the margins of sedimentary basins overrun by the Laurentide Ice Sheet totals about 3.7 × 104 km3, which is about 0.2% of the volume of the Laurentide Ice Sheet. Subglacial infiltration estimates based on continental-scale hydrologic models are even higher (5-10% of meltwater generated). These studies in sum call into question the widely held notion that groundwater flow patterns within confined aquifer systems are controlled primarily by the water table configuration during the Pleistocene. Rather, groundwater flow patterns were likely much more complex and transient in nature than has previously been thought. Because Pleistocene recharge rates are believed to be highly variable, these studies have profound implications for water resource managers charged with determining sustainable pumping rates from confined aquifers that host ice sheet meltwater.

15. MAP OF ALAMEDA SHIPYARD SHOWING PROPOSED ADDITIONAL FACILITIES. United ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

15. MAP OF ALAMEDA SHIPYARD SHOWING PROPOSED ADDITIONAL FACILITIES. United Engineering Company Ltd., Alameda Shipyard. A site map with all existing structures keyed to an identification legend. Also shows proposed new structures. No architect noted. Drawn by "J.B.H." (John Hudspeth?). Sheet 2. Plan no. 10,528. Scale one inch to 100 feet. November 12, 1943, last revised 1/18/44. pencil on vellum - United Engineering Company Shipyard, 2900 Main Street, Alameda, Alameda County, CA

4. FLOOR PLAN AND SECTIONS, ADDITION TO POWER HOUSE. United ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

4. FLOOR PLAN AND SECTIONS, ADDITION TO POWER HOUSE. United Engineering Company Ltd., Alameda Shipyard. Also includes plot plan at 1 inch to 100 feet. John Hudspeth, architect, foot of Main Street, Alameda, California. Sheet 3. Plan no. 10,548. Scale 1/4 inch and h inch to the foot. April 30, 1945, last revised 6/22/45. pencil on vellum - United Engineering Company Shipyard, Boiler House, 2900 Main Street, Alameda, Alameda County, CA

A new tensile impact test for the toughness characterization of sheet material

NASA Astrophysics Data System (ADS)

Könemann, Markus; Lenz, David; Brinnel, Victoria; Münstermann, Sebastian

2018-05-01

In the past, the selection of suitable steels has been carried out primarily based on the mechanical properties of different steels. One of these properties is the resistance against crack propagation. For many constructions, this value plays an important role, because it can compare the impact toughness of different steel grades easily and gives information about the loading capacity of the specific materials. For thin sheets, impact toughness properties were usually not considered. One of the reasons for this is that the Charpy-impact test is not applicable for sheets with thicknesses below 2 mm. For a long time, this was not relevant because conventional steels had a sufficient impact toughness in a wide temperature range. However, since new multiphase steel grades with improved mechanical property exploitations are available, it turned out that impact toughness properties need to be considered during the component design phase, as the activation of the cleavage fracture mechanism is observed under challenging loading conditions. Therefore, this work aims to provide a new and practical testing procedure for sheet material or thin walled structures. The new testing procedure is based on tensile tests conducted in an impact pendulum similar to the Charpy impact hammer. A new standard geometry is provided, which enables a comparison between different steels or steel grades. A connection to the conventional Charpy test is presented using a damage mechanics model, which predicts material failure with consideration of to the stress state at various temperatures. Different specimen geometries are analysed to cover manifold stress states. A special advantage of the damage mechanics model is also the possibility to predict the materials behaviour in the transition area. To verify the method a conventional steel was tested in Charpy tests as well as in the new tensile impact test.

Characterising ductility of 6xxx-series aluminium sheet alloys at combined loading conditions

NASA Astrophysics Data System (ADS)

Henn, Philipp; Liewald, Mathias; Sindel, Manfred

2017-10-01

This paper presents a new approach to characterise material ductility when combined, three dimensional loading conditions occurring during vehicle crash are applied. So called "axial crush test" of closed hat sections is simplified by reducing it down to a two-dimensional testing procedure. This newly developed edge-compression test (ECT) provides the opportunity to investigate a defined characteristic axial folding behaviour of a profile edge. The potential to quantify and to differentiate crashworthiness of material by use of new edge-compression test is investigated by carrying out experimental studies with two different 6xxx-aluminium sheet alloys.

Mental Health Care: Licensing and Certification Requirements for Staff in State Hospitals. Fact Sheet for the Honorable Daniel K. Inouye, United States Senate.

ERIC Educational Resources Information Center

General Accounting Office, Washington, DC. Div. of Human Resources.

The Office of United States Senator Daniel Inouye requested information on state minimum licensing and certification requirements for physicians, psychiatrists, psychologists, social workers, and nurses who work directly with patients in state mental hospitals. To obtain this information, the General Accounting Office called the offices of the…

The Energy Dome. Social Studies Packet-Grades 4, 5, 6.

ERIC Educational Resources Information Center

National Science Teachers Association, Washington, DC.

This teacher's guide contains a unit of study for teaching about energy in grades four, five, and six. The guide is self-contained and includes the fact sheets students need to work out the activity problems. The unit is organized around the theme of the domed athletic stadium. The students begin by surveying the energy it takes to travel from…

Profit--The Key. Principles of the American Free Enterprise System for Distributive Education Students. Instructor's Guide.

ERIC Educational Resources Information Center

Hook, Sallie A.; And Others

In this distributive education unit teacher's guide on the free enterprise system, principles of the American economic system are introduced as they relate to marketing and distribution. (The study guide is available as CE 020 458.) The guide preview sheet includes a list of audiovisual equipment necessary, duration of the unit (sixteen to…

37 CFR 2.190 - Addresses for trademark correspondence with the United States Patent and Trademark Office.

Code of Federal Regulations, 2010 CFR

2010-07-01

... filed through the Office's web site, at http://www.uspto.gov. Paper documents and cover sheets to be... trademark documents can be ordered through the Office's web site at www.uspto.gov. Paper requests for...: Madrid Processing Unit, 600 Dulany Street, MDE-7B87, Alexandria, VA 22314-5793. [68 FR 48289, Aug. 13...

Research Facts on Homeschooling. General Facts and Trends

ERIC Educational Resources Information Center

Ray, Brian D.

2006-01-01

This fact sheet presents the following general facts and trends. Homeschooling may be the fastest-growing form of education in the United States and it is also growing around the world in many nations. There are about 2 million homeschool students in the United States. There were an estimated 1.9 to 2.4 million children (in grades K to 12) home…

EnviroAtlas - Industrial Water Demand by 12-Digit HUC for the Conterminous United States

EPA Pesticide Factsheets

This EnviroAtlas dataset includes industrial water demand attributes which provide insight into the amount of water currently used for manufacturing and production of commodities in the contiguous United States. The values are based on 2005 water demand and Dun and Bradstreet's 2009/2010 source data, and have been summarized by watershed or 12-digit hydrologic unit code (HUC). For the purposes of this metric, industrial water use includes chemical, food, paper, wood, and metal production. The industrial water is for self-supplied only such as by private wells or reservoirs. Sources include either surface water or groundwater. This dataset was produced by the US EPA to support research and online mapping activities related to the EnviroAtlas. EnviroAtlas (https://www.epa.gov/enviroatlas) allows the user to interact with a web-based, easy-to-use, mapping application to view and analyze multiple ecosystem services for the contiguous United States. The dataset is available as downloadable data (https://edg.epa.gov/data/Public/ORD/EnviroAtlas) or as an EnviroAtlas map service. Additional descriptive information about each attribute in this dataset can be found in its associated EnviroAtlas Fact Sheet (https://www.epa.gov/enviroatlas/enviroatlas-fact-sheets).

EnviroAtlas - Big Game Hunting Recreation Demand by 12-Digit HUC in the Conterminous United States

EPA Pesticide Factsheets

This EnviroAtlas dataset includes the total number of recreational days per year demanded by people ages 18 and over for big game hunting by location in the contiguous United States. Big game includes deer, elk, bear, and wild turkey. These values are based on 2010 population distribution, 2011 U.S. Fish and Wildlife Service (FWS) Fish, Hunting, and Wildlife-Associated Recreation (FHWAR) survey data, and 2011 U.S. Department of Agriculture (USDA) Forest Service National Visitor Use Monitoring program data, and have been summarized by 12-digit hydrologic unit code (HUC). This dataset was produced by the US EPA to support research and online mapping activities related to the EnviroAtlas. EnviroAtlas (https://www.epa.gov/enviroatlas) allows the user to interact with a web-based, easy-to-use, mapping application to view and analyze multiple ecosystem services for the contiguous United States. The dataset is available as downloadable data (https://edg.epa.gov/data/Public/ORD/EnviroAtlas) or as an EnviroAtlas map service. Additional descriptive information about each attribute in this dataset can be found in its associated EnviroAtlas Fact Sheet (https://www.epa.gov/enviroatlas/enviroatlas-fact-sheets).

Geologic map of Gunnison Gorge National Conservation Area, Delta and Montrose Counties, Colorado

USGS Publications Warehouse

Kellogg, Karl; Hansen, Wallace R.; Tucker, Karen S.; VanSistine, D. Paco

2004-01-01

This publication consists of a geologic map database and printed map sheet. The map sheet has a geologic map as the center piece, and accompanying text describes (1) the various geological units, (2) the uplift history of the region and how it relates to canyon downcutting, (3) the ecology of the gorge, and (4) human history. The map is intended to be used by the general public as well as scientists and goes hand-in-hand with a separate geological guide to Gunnison Gorge.

Exploring the Moon: A teacher's guide with activities for Earth and space sciences

NASA Technical Reports Server (NTRS)

Taylor, G. Jeffrey; Martel, Linda M. V.; Bays, Brooks G., Jr.

1994-01-01

This guide contains educational materials designed for use in upper elementary through high schools with the Lunar Sample Disk. A set of thirty-six 35-mm slides complements the activities in this guidebook. The book contains: (1) information on the Lunar Sample Disk; (2) a curriculum content matrix; (3) a teacher's guide; (4) moon ABC's fact sheet; (5) rock ABC's fact sheet; (6) progress in Lunar Science chart; (7) seventeen activities; (8) a resource section for each unit; (9) a glossary; and (10) a list of NASA educational resources.

Advanced Development Waste Processing Unit for Combat Vehicles. Phase 2

DTIC Science & Technology

1987-12-29

Johns Manville Manufacturers # : 5346474 Type: Cera Blanket Size: 6 lb., I" thick Amount Used: 24" x 48" total TIME RPM TI O T 2 F T ,F T 4, Tbient F 1200...WPUBMO01 DATA SHEET DSO01-4 Date:NOV 2 5 186 i~ L , Candidate Insulation: Manufacturer: Johns Manville Manufacturer’s # : 5346474. Type: Cera Blanket Size...SHEET DS001-5 Date: EC 0 3 186 Candidate Insulation: Manufacturer: Johns Manville Manufacturerls # : 5346474 Type: Cera Blanket (F Size: 6 lb., 1

Repair and retrofit of concrete bridge girders using hybrid FRP sheets.

DOT National Transportation Integrated Search

2012-02-01

The use of carbon fibers (CF) and glass fibers (GF) were combined to strengthen potentially non-ductile flexural : members. Based on tension tests of fiber-reinforced polymer (FRP) rovings and sheets, as well as theoretical : research on hybrid FRP, ...

Response of the Antarctic ice sheet to ocean forcing using the POPSICLES coupled ice sheet-ocean model

NASA Astrophysics Data System (ADS)

Martin, D. F.; Asay-Davis, X.; Price, S. F.; Cornford, S. L.; Maltrud, M. E.; Ng, E. G.; Collins, W.

2014-12-01

We present the response of the continental Antarctic ice sheet to sub-shelf-melt forcing derived from POPSICLES simulation results covering the full Antarctic Ice Sheet and the Southern Ocean spanning the period 1990 to 2010. Simulations are performed at 0.1 degree (~5 km) ocean resolution and ice sheet resolution as fine as 500 m using adaptive mesh refinement. A comparison of fully-coupled and comparable standalone ice-sheet model results demonstrates the importance of two-way coupling between the ice sheet and the ocean. The POPSICLES model couples the POP2x ocean model, a modified version of the Parallel Ocean Program (Smith and Gent, 2002), and the BISICLES ice-sheet model (Cornford et al., 2012). BISICLES makes use of adaptive mesh refinement to fully resolve dynamically-important regions like grounding lines and employs a momentum balance similar to the vertically-integrated formulation of Schoof and Hindmarsh (2009). Results of BISICLES simulations have compared favorably to comparable simulations with a Stokes momentum balance in both idealized tests like MISMIP3D (Pattyn et al., 2013) and realistic configurations (Favier et al. 2014). POP2x includes sub-ice-shelf circulation using partial top cells (Losch, 2008) and boundary layer physics following Holland and Jenkins (1999), Jenkins (2001), and Jenkins et al. (2010). Standalone POP2x output compares well with standard ice-ocean test cases (e.g., ISOMIP; Losch, 2008) and other continental-scale simulations and melt-rate observations (Kimura et al., 2013; Rignot et al., 2013). A companion presentation, "Present-day circum-Antarctic simulations using the POPSICLES coupled land ice-ocean model" in session C027 describes the ocean-model perspective of this work, while we focus on the response of the ice sheet and on details of the model. The figure shows the BISICLES-computed vertically-integrated ice velocity field about 1 month into a 20-year coupled Antarctic run. Groundling lines are shown in green.

Determination of Flaw Growth Characteristics of Ti-6Al-4V Sheet in the Solution-Treated and Aged Condition

NASA Technical Reports Server (NTRS)

Hoeppner, David W.; Pettit, Donald E.; Feddersen, Charles E.; Hyler, Walter S.

1968-01-01

The specific experimental investigation undertaken was designed to answer these questions on Ti-6Al-4V in the solution treated and aged condition. The defect growth and fracture characteristics were studied in parent (unwelded) and welded sheet material. The results of the study indicate that cryogenic proof testing will screen smaller size defects than proof testing at ambient conditions. However some unusual crack growth behavior during the proof test simulation suggests that some further study be made of stress and time duration effects.

The Fatigue Characteristics of Bolted Lap Joints of 24S-T Alclad Sheet Materials

DTIC Science & Technology

1946-10-01

extremely close bolt fits are needed to o%tain maximum life of bolt ~oint~ under repeated etreseeci. -. Szvzral ty~+?+s of bolt patterns hava been tegted...Memorial Institute on spec~meris of 0.102-i.nch sheet. In particular, figure 4 shows, on a load- life diagram, . results of tests Qn single-bolt...results of tests at the Univer- sity of’ il~~nols on single—bolt specimens, Tables 10 and 11 give reeults of tests, made at the U“ uiversity of Illino~8 , on

Lightweight Long Life Heat Exchanger

NASA Technical Reports Server (NTRS)

Moore, E. K.

1976-01-01

A shuttle orbiter flight configuration aluminum heat exchanger was designed, fabricated, and tested. The heat exchanger utilized aluminum clad titanium composite parting sheets for protection against parting sheet pin hole corrosion. The heat exchanger, which is fully interchangeable with the shuttle condensing heat exchanger, includes slurpers (a means for removing condensed water from the downstream face of the heat exchanger), and both the core air passes and slurpers were hydrophilic coated to enhance wettability. The test program included performance tests which demonstrated the adequacy of the design and confirmed the predicted weight savings.

Prediction of the Forming Limit Band for Steel Sheets using a new Formulation of Hora's Criterion (MMFC)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sorin Comsa, Dan; Dragos, George; Paraianu, Liana

2011-01-17

The paper analyzes the dispersion of the mechanical parameters and its influence on the forming limit curves of sheet metals. The tests have been made for the case of the DC01 steel sheets. The dispersion of the mechanical parameters has been observed during the experimental research. On the basis of this dispersion, a forming limit band has been calculated using an alternate formulation of Hora's model (MMFC).

Tip Sheets

Science.gov Websites

United States Census Bureau Topics Population Latest Information Age and Sex Ancestry Children Mobility Population Estimates Population Projections Race Veterans Economy Latest Information Portal Other Economic Programs Business Latest Information Business Characteristics Classification Codes

7 CFR 52.784 - Score sheet for canned red tart pitted cherries.

Code of Federal Regulations, 2010 CFR

2010-01-01

... UNDER THE AGRICULTURAL MARKETING ACT OF 1946 PROCESSED FRUITS AND VEGETABLES, PROCESSED PRODUCTS THEREOF, AND CERTAIN OTHER PROCESSED FOOD PRODUCTS 1 United States Standards for Grades of Canned Red Tart...

Chemical vapor deposition growth

NASA Technical Reports Server (NTRS)

Ruth, R. P.; Manasevit, H. M.; Kenty, J. L.; Moudy, L. A.; Simpson, W. I.; Yang, J. J.

1976-01-01

The chemical vapor deposition (CVD) method for the growth of Si sheet on inexpensive substrate materials is investigated. The objective is to develop CVD techniques for producing large areas of Si sheet on inexpensive substrate materials, with sheet properties suitable for fabricating solar cells meeting the technical goals of the Low Cost Silicon Solar Array Project. Specific areas covered include: (1) modification and test of existing CVD reactor system; (2) identification and/or development of suitable inexpensive substrate materials; (3) experimental investigation of CVD process parameters using various candidate substrate materials; (4) preparation of Si sheet samples for various special studies, including solar cell fabrication; (5) evaluation of the properties of the Si sheet material produced by the CVD process; and (6) fabrication and evaluation of experimental solar cell structures, using standard and near-standard processing techniques.

Development of 1500mm Wide Wrought Magnesium Alloys by Twin Roll Casting Technique in Turkey

NASA Astrophysics Data System (ADS)

Duygulu, Ozgur; Ucuncuoglu, Selda; Oktay, Gizem; Temur, Deniz Sultan; Yucel, Onuralp; Kaya, Ali Arslan

Magnesium alloy AZ31, AZ61, AZ91, AM50 and AM60 sheets were produced by twin roll casting first time in Turkey. Sheets of 4.5-6.5mm thick and 1500mm width were successfully achieved. Microstructure of the sheet was analyzed by optical microscope, scanning electron microscope (SEM) and transmission electron microscope (TEM). Semi-quantitative analyses were performed by SEM-EDS. In addition, X-ray studies were performed for both characterization and texture purposes. Mechanical properties were investigated by tensile tests and also hardness measurements. Homogenization and annealing heat treatments were performed on the produced sheets.

Lightweight Solar Paddle with High Specific Power of 150 W/Kg

NASA Astrophysics Data System (ADS)

Shimazaki, Kazunori; Takahashi, Masato; Imaizumi, Mitsuru; Takamoto, Tatsuya; Ito, Takehiko; Nozaki, Yukishige; Kusawake, Hiroaki

2014-08-01

A lightweight solar paddle using space solar sheet (SSS) is currently being developed, which uses glass-type SSS (G-SSS) comprising InGaP/GaAs/InGaAs triple- junction high-efficiency thin-film solar cells. To avoid damage to the G-SSS due to vibration during launch, we adopted a new architecture on a panel. This panel employed a curved frame-type structure, on which the G-SSS is mounted and test models were manufactured to evaluate the vibration tolerance. The dimensions of the 1.0-cm-thick unit panel were about 1.0 × 1.0 m. Acoustic and sine vibration tests were performed on the model and the results demonstrated the high durability of the curved panel in an acoustic and vibration environments. The specific power of the solar paddle using the curved panel is estimated at approximately 150 W/kg at an array power of about 10 kW.

Development of a tornado safe room door from wood Products: door design and impact testing

Treesearch

Robert H. Falk; James J. Bridwell

2016-01-01

In this study, a tornado safe room door built from wood products and steel sheeting was developed and impact-tested according to tornado safe room standards. Results indicate that an door constructed from as few as two sheets of 23/32-in. (18.26-mm) construction-grade plywood and overlaid with 18-gauge (0.05-in.- (1.27- mm-) thick) steel can pass the required impact...

Characterization of the strain-life fatigue properties of thin sheet metal using an optical extensometer

NASA Astrophysics Data System (ADS)

Zhang, Shuiqiang; Mao, Shuangshuang; Arola, Dwayne; Zhang, Dongsheng

2014-09-01

Characterizing the strain-life fatigue behavior of thin sheet metals is often challenging since the required specimens have short gauge lengths to avoid buckling, thereby preventing the use of conventional mechanical extensometers. To overcome this obstacle a microscopic optical imaging system has been developed to measure the strain amplitude during fatigue testing using Digital Image Correlation (DIC). A strategy for rapidly recording images is utilized to enable sequential image sampling rates of at least 10 frames per second (fps) using a general digital camera. An example of a complete strain-life fatigue test for thin sheet steel under constant displacement control is presented in which the corresponding strain within the gage section of the specimen is measured using the proposed imaging system. The precision in strain measurement is assessed and methods for improving the image sampling rates in dynamic testing are discussed.

Detailed sections from auger holes in the Elizabethtown 1:100,000-scale map sheet, North Carolina

USGS Publications Warehouse

Weems, Robert E.; Lewis, William C.; Murray, Joseph H.; Queen, David B.; Grey, Jeffrey B.; DeJong, Benjamin D.

2011-01-01

The Elizabethtown 1:100,000 quadrangle is in the west-central part of the Coastal Plain of southeastern North Carolina. The Coastal Plain, in this region, consists mostly of unlithified sediments that range in age from Late Cretaceous to Holocene. These sediments lie with profound unconformity on complexly deformed metamorphic and igneous rocks similar to rocks found immediately to the west in the Piedmont province. Coastal Plain sediments generally dip gently to the southeast or south and reach a maximum thickness of about 850 feet (ft) in the extreme southeast part of the map area. The gentle southerly and southeasterly dip is disrupted in several areas by faulting. The U.S. Geological Survey recovered one core and augered 196 research test holes in the Elizabethtown 1:100,000 quadrangle to supplement sparse outcrop data in the map area. The recovered sediments were studied and data from these sediments recorded to determine the lithologic characteristics, spatial distribution, and temporal framework of the represented Coastal Plain stratigraphic units. These test holes were critical for accurately determining the distribution of major geologic units and the position of unit boundaries. The detailed descriptions of the subsurface data can be used by geologists, hydrologists, engineers, and community planners to provide a detailed shallow-subsurface stratigraphic framework for the Elizabethtown map region.

Basal Freeze-on: An Active Component of Hydrology from the Ice Divide to the Margin

NASA Astrophysics Data System (ADS)

Bell, R. E.; Tinto, K. J.; Abdi, A.; Creyts, T. T.; Wolovick, M.; Das, I.; Ferraccioli, F.; Csatho, B. M.

2012-12-01

Subglacial hydrology is considered a key control of ice sheet dynamics. Here we show that basal freeze-on is a process that can terminate basal hydrologic networks both in the interior of East Antarctica and at the margins of the Greenland Ice Sheet. Basal freeze-on modifies the ice thickness, ice structure, and ice rheology and therefore must be considered in developing accurate understanding of how hydrology interacts with ice dynamics. In East Antarctica, the freeze-on process follows well-defined hydrologic networks within Gamburtsev Mountain valleys. The steep mountain topography strongly controls the routing of the subglacial water. Ice surface slope drives the water up the mountain valleys and freeze-on occurs at the valley heads. Freeze-on ice is characterized by distinct basal radar reflectors that emerge from the hydrologic network. Evidence that these spatially coherent reflectors demark accreted ice is the upward deflection of the overlying internal layers accompanied by thickening of base of the ice sheet. Individual accretion bodies can be 25 km wide across flow, 100 km along flow with average thicknesses of ~500m although the maximum thickness is 1100m. Regional accumulation rates near the accretion sites average 4cm/yr with low ice velocity (1.5 m/yr). The volume of the ice enclosed by the accretion ice reflectors is 45-1064 km3. The accretion occurs beneath 2200-3000m thick ice and has been persistent for at least 50,000yr. Other basal reflectors in northern Greenland appear in radar from NASA's Icebridge mission and CRESIS. To identify freeze-on ice, we use specific criteria: reflectors must originate from the bed, must be spatially continuous from line to line and the meteoric stratigraphy is deflected upward. The absence of coincident gravity anomalies indicates these reflectors define distinct packages of ice rather than frozen sediment or off-nadir subglacial topography. In the Petermann Glacier Catchment, one of the largest in northern Greenland, we have identified 14 distinct basal ice packages over a wide region. The accumulation rate (~17 cm/yr) and ice velocity (~5-200m/yr) are higher than East Antarctica. These accretion bodies are 10-50 km wide, up to 940m thick and can be traced up to 140 km. The volume of the ice enclosed by the accretion ice reflector units is ~70-300 km3. We estimate that the freeze-on process in Petermann has been active for at least 6,000yr. Water has been mapped beneath much of the Greenland ice sheet and adjacent to the inland freeze-on site flat bright reflectors are interpreted as basal water. The onset of fast flow in Petermann Glacier is associated with the development of the thickest unit of freeze-on ice. Other areas of Greenland also have basal freeze-on ice. North of Jakobshavn Isbrae where the ice sheet is ~1000 m thick, evidence exists for a nearly 10 km wide, 200 m thick unit of basal ice in airborne radar. Located close to the site where basal freeze-on outcrops at the ice sheet margin at Pakitsoq, this unit may be the result of freeze-on of water draining from a supraglacial lake. Basal freeze-on is a critical component of subglacial hydrology. The evidence for large scale freeze-on East Antarctica and many areas of Greenland indicates widespread modification of the base of the ice sheet by basal hydrology.

Development of a Solar Cell Back Sheet with Excellent UV Durability and Thermal Conductivity.

PubMed

Kang, Seong-Hwan; Choi, Jaeho; Lee, Sung-Ho; Song, Young-Hoon; Park, Jong-Se; Jung, In-Sung; Jung, Jin-Su; Kim, Chong-Yeal; Yang, O-Bong

2018-09-01

The back sheet is one of the most important materials in photovoltaic (PV) modules. It plays an important role in protecting the solar cell from the environment by preventing moisture penetration. In the back sheet, the outermost layer is composed of a polyester (PET) film to protect the PV module from moisture, and the opposite layer is composed of a TiO2 + PE material. Nowadays, PV modules are installed in the desert. Therefore, methods to improve the power generation efficiency of PV modules need to be investigated as the efficiency is affected by temperature resulting from the heat radiation effect. Using a back sheet with a high thermal conductivity, the module output efficiency can be increased as heat is efficiently dissipated. In this study, a thermally conductive film was fabricated by mixing a reference film (TiO2 + PE) and a non-metallic material, MgO, with high thermal conductivity. UV irradiation tests of the film were conducted. The thermally conductive film (TiO2 + PE + MgO) showed higher conductivity than a reference film. No visible cracks and low yellowing degree were found in thermally conductive film, confirming its excellent UV durability characteristics. The sample film was bonded to a PET layer, and a back sheet was fabricated. The yellowing of the back sheet was also analyzed after UV irradiation. In addition, mini modules with four solar cell were fabricated using the developed back sheet, and a comparative outdoor test was conducted. The results showed that power generation improved by 1.38%.

Higher Sensitivity in X-Ray Photography

NASA Technical Reports Server (NTRS)

Buggle, R. N.

1986-01-01

Hidden defects revealed if X-ray energy decreased as exposure progresses. Declining-potential X-ray photography detects fractures in thin metal sheet covered by unbroken sheet of twice thickness. Originally developed to check solder connections on multilayer circuit boards, technique has potential for other nondestructive testing.

Sensitivity of Pliocene ice sheets to orbital forcing

USGS Publications Warehouse

Dolan, A.M.; Haywood, A.M.; Hill, D.J.; Dowsett, H.J.; Hunter, S.J.; Lunt, D.J.; Pickering, S.J.

2011-01-01

The stability of the Earth's major ice sheets is a critical uncertainty in predictions of future climate and sea level change. One method of investigating the behaviour of the Greenland and the Antarctic ice sheets in a warmer-than-modern climate is to look back at past warm periods of Earth history, for example the Pliocene. This paper presents climate and ice sheet modelling results for the mid-Pliocene warm period (mPWP; 3.3 to 3.0 million years ago), which has been identified as a key interval for understanding warmer-than-modern climates (Jansen et al., 2007). Using boundary conditions supplied by the United States Geological Survey PRISM Group (Pliocene Research, Interpretation and Synoptic Mapping), the Hadley Centre coupled ocean–atmosphere climate model (HadCM3) and the British Antarctic Survey Ice Sheet Model (BASISM), we show large reductions in the Greenland and East Antarctic Ice Sheets (GrIS and EAIS) compared to modern in standard mPWP experiments. We also present the first results illustrating the variability of the ice sheets due to realistic orbital forcing during the mid-Pliocene. While GrIS volumes are lower than modern under even the most extreme (cold) mid-Pliocene orbit (losing at least 35% of its ice mass), the EAIS can both grow and shrink, losing up to 20% or gaining up to 10% of its present-day volume. The changes in ice sheet volume incurred by altering orbital forcing alone means that global sea level can vary by more than 25 m during the mid-Pliocene. However, we have also shown that the response of the ice sheets to mPWP orbital hemispheric forcing can be in anti-phase, whereby the greatest reductions in EAIS volume are concurrent with the smallest reductions of the GrIS. If this anti-phase relationship is in operation throughout the mPWP, then the total eustatic sea level response would be dampened compared to the ice sheet fluctuations that are theoretically possible. This suggests that maximum eustatic sea level rise does not correspond to orbital maxima, but occurs at times where the anti-phasing of Northern and Southern Hemisphere ice sheet retreat is minimised.

An Investigation on Low Velocity Impact Response of Multilayer Sandwich Composite Structures

PubMed Central

Jedari Salami, S.; Sadighi, M.; Shakeri, M.; Moeinfar, M.

2013-01-01

The effects of adding an extra layer within a sandwich panel and two different core types in top and bottom cores on low velocity impact loadings are studied experimentally in this paper. The panel includes polymer composite laminated sheets for faces and the internal laminated sheet called extra layer sheet, and two types of crushable foams are selected as the core material. Low velocity impact tests were carried out by drop hammer testing machine to the clamped multilayer sandwich panels with expanded polypropylene (EPP) and polyurethane rigid (PUR) in the top and bottom cores. Local displacement of the top core, contact force and deflection of the sandwich panel were obtained for different locations of the internal sheet; meanwhile the EPP and PUR were used in the top and bottom cores alternatively. It was found that the core material type has made significant role in improving the sandwich panel's behavior compared with the effect of extra layer location. PMID:24453804

Slicing of Silicon into Sheet Material. Silicon Sheet Growth Development for the Large Area Silicon Sheet Task of the Low Cost Solar Array Project

NASA Technical Reports Server (NTRS)

Fleming, J. R.; Holden, S. C.; Wolfson, R. G.

1979-01-01

The use of multiblade slurry sawing to produce silicon wafers from ingots was investigated. The commercially available state of the art process was improved by 20% in terms of area of silicon wafers produced from an ingot. The process was improved 34% on an experimental basis. Economic analyses presented show that further improvements are necessary to approach the desired wafer costs, mostly reduction in expendable materials costs. Tests which indicate that such reduction is possible are included, although demonstration of such reduction was not completed. A new, large capacity saw was designed and tested. Performance comparable with current equipment (in terms of number of wafers/cm) was demonstrated.

Tapping the deglacial secrets of Lake Oneida sediments: Establishing a connection between radiocarbon and paleomagnetics in Fish Creek sediments

NASA Astrophysics Data System (ADS)

Peck, D.; Rosenheim, B. E.; Ridge, J. C.

2017-12-01

Postglacial varved and rhythmically-laminated clays deposited within the Ontario Basin are often associated with the retreat of the Laurentide Ice Sheet immediately preceding the onset of the Younger Dryas. The paleoclimatic significance of the Ontario Basin has made it a popularly studied region. To determine ages that correlate with ice sheet retreat, classical radiocarbon ages were generated. However low total organic carbon (TOC) values found in glaciolacustrine sediments make accuracy of data a concern. Using the magnetic orientation of sediments during deposition, paleomagnetism has presented reliable dates in similar regions across the northeastern United States. While useful, paleomagnetism also comes with limitations, which have left areas of unexplored research. Lake Oneida, last glaciated by the Ontario Lobe, is one of the deepest and most untapped reservoirs of sediment dating back to the retreat of the Laurentide Ice Sheet, due primarily to the difficulty it poses for classical methods. Using samples taken from exposed varved glaciolacustrine sediment exposed by the downcutting of Fish Creek, a fluvial system terminating in eastern Lake Oneida, we compare Ramped Pyrolysis 14C data with paleomagnetic data. Ramped PyrOx 14C data unmask the distribution of ages in the organic matter of these sediments, at least partially separating autochthonous sources of carbon from allochthonous sources that tend to be older in these settings. Our comparison will test whether Ramped PyrOx 14C data match paleomagnetic data well enough to be used as the sole chronometer in sediment cores taken from Lake Oneida cores for which paleomagnetic orientation becomes more difficult to ascertain.

Topical Application of a Silicone Gel Sheet with Verapamil Microparticles in a Rabbit Model of Hypertrophic Scar.

PubMed

Rha, Eun Young; Kim, Yun Ho; Kim, Tae-Jung; Yoo, Gyeol; Rhie, Jong Won; Kim, Hyun-Jung; Park, Il-Kyu

2016-01-01

The authors developed a novel treatment based on the topical application of a silicone gel sheet containing verapamil microparticles. The ability of these silicone gel sheets to inhibit hypertrophic scar in a rabbit ear wound model was examined. Ten New Zealand White rabbits with a total of 80 wounds in both ears were used in this study. The rabbits were divided into five groups (control; silicone gel sheet; and silicone gel sheet plus 0.25, 2.5, and 25 mg of verapamil per gram). Histopathologic findings were quantified. The mean scar elevation index, fibroblast counts, and capillary counts differed significantly among the five groups (p < 0.05). The median scar elevation index was significantly lower in the silicone gel sheet plus 2.5 mg of verapamil per gram group than in the silicone gel sheet group (1.2 versus 2.2). The median number of fibroblasts was significantly lower in the silicone gel sheet plus 0.25 mg of verapamil per gram group than in the silicone gel sheet group (172.5 versus 243). In the median number of capillary lumina, there was no significant difference between the silicone gel sheet group and the silicone gel sheet plus 0.25, 2.5, and 25 mg of verapamil per gram groups (28.5, 18, 20, and 18, respectively). Topical application of a silicone gel sheet with verapamil microparticles may be a novel, effective treatment method for hypertrophic scar, but its safety and efficacy in humans must be tested in clinical trials.

Sheet Membrane Spacesuit Water Membrane Evaporator

NASA Technical Reports Server (NTRS)

Bue, Grant; Trevino, Luis; Zapata, Felipe; Dillion, Paul; Castillo, Juan; Vonau, Walter; Wilkes, Robert; Vogel, Matthew; Frodge, Curtis

2013-01-01

A document describes a sheet membrane spacesuit water membrane evaporator (SWME), which allows for the use of one common water tank that can supply cooling water to the astronaut and to the evaporator. Test data showed that heat rejection performance dropped only 6 percent after being subjected to highly contaminated water. It also exhibited robustness with respect to freezing and Martian atmospheric simulation testing. Water was allowed to freeze in the water channels during testing that simulated a water loop failure and vapor backpressure valve failure. Upon closing the backpressure valve and energizing the pump, the ice eventually thawed and water began to flow with no apparent damage to the sheet membrane. The membrane evaporator also serves to de-gas the water loop from entrained gases, thereby eliminating the need for special degassing equipment such as is needed by the current spacesuit system. As water flows through the three annular water channels, water evaporates with the vapor flowing across the hydrophobic, porous sheet membrane to the vacuum side of the membrane. The rate at which water evaporates, and therefore, the rate at which the flowing water is cooled, is a function of the difference between the water saturation pressure on the water side of the membrane, and the pressure on the vacuum side of the membrane. The primary theory is that the hydrophobic sheet membrane retains water, but permits vapor pass-through when the vapor side pressure is less than the water saturation pressure. This results in evaporative cooling of the remaining water.

Medication reconciliation in acute care: ensuring an accurate drug regimen on admission and discharge.

PubMed

Rodehaver, Claire; Fearing, Deb

2005-07-01

Several factors contribute to the potential for patient confusion regarding his or her medication regimen, including multiple names for a single drug and formulary variations when the patient receives medications from more than one pharmacy. A 68-year-old woman was discharged from the hospital on a HMG-CoA reductase inhibitor (statin) and resumed her home statin. Eleven days later she returned to the hospital with a diagnosis of severe rhabdomyolysis due to statin overdose. IMPLEMENTING SOLUTIONS: Miami Valley Hospital, Dayton, Ohio, implemented a reconciliation process and order form at admission and discharge to reduce the likelihood that this miscommunication would recur. Initial efforts were trialed on a 44-bed orthopedic unit, with spread of the initiative to the cardiac units and finally to the remaining 22 nursing units. The team successfully implemented initiation of the order sheet, yet audits indicated the need for improvement in reconciling the medications within 24 hours of admission and in reconciling the home medications at the point of discharge. Successful implementation of the order sheet to drive reconciliation takes communication, perseverance, and a multidisciplinary team approach.

Bond–Slip Relationship for CFRP Sheets Externally Bonded to Concrete under Cyclic Loading

PubMed Central

Li, Ke; Cao, Shuangyin; Yang, Yue; Zhu, Juntao

2018-01-01

The objective of this paper was to explore the bond–slip relationship between carbon fiber-reinforced polymer (CFRP) sheets and concrete under cyclic loading through experimental and analytical approaches. Modified beam tests were performed in order to gain insight into the bond–slip relationship under static and cyclic loading. The test variables are the CFRP-to-concrete width ratio, and the bond length of the CFRP sheets. An analysis of the test results in this paper and existing test results indicated that the slope of the ascending segment of the bond–slip curve decreased with an increase in the number of load cycles, but the slip corresponding to the maximum shear stress was almost invariable as the number of load cycles increased. In addition, the rate of reduction in the slope of the ascending range of the bond–slip curve during cyclic loading decreased as the concrete strength increased, and increased as the load level or CFRP-to-concrete width ratio enhanced. However, these were not affected by variations in bond length if the residual bond length was longer than the effective bond length. A bilinear bond–slip model for CFRP sheets that are externally bonded to concrete under cyclic loading, which considered the effects of the cyclic load level, concrete strength, and CFRP-to-concrete ratio, was developed based on the existing static bond–slip model. The accuracy of this proposed model was verified by a comparison between this proposed model and test results. PMID:29495383

Bond-Slip Relationship for CFRP Sheets Externally Bonded to Concrete under Cyclic Loading.

PubMed

Li, Ke; Cao, Shuangyin; Yang, Yue; Zhu, Juntao

2018-02-26

The objective of this paper was to explore the bond-slip relationship between carbon fiber-reinforced polymer (CFRP) sheets and concrete under cyclic loading through experimental and analytical approaches. Modified beam tests were performed in order to gain insight into the bond-slip relationship under static and cyclic loading. The test variables are the CFRP-to-concrete width ratio, and the bond length of the CFRP sheets. An analysis of the test results in this paper and existing test results indicated that the slope of the ascending segment of the bond-slip curve decreased with an increase in the number of load cycles, but the slip corresponding to the maximum shear stress was almost invariable as the number of load cycles increased. In addition, the rate of reduction in the slope of the ascending range of the bond-slip curve during cyclic loading decreased as the concrete strength increased, and increased as the load level or CFRP-to-concrete width ratio enhanced. However, these were not affected by variations in bond length if the residual bond length was longer than the effective bond length. A bilinear bond-slip model for CFRP sheets that are externally bonded to concrete under cyclic loading, which considered the effects of the cyclic load level, concrete strength, and CFRP-to-concrete ratio, was developed based on the existing static bond-slip model. The accuracy of this proposed model was verified by a comparison between this proposed model and test results.

User Guide for Automated Wetland Determination Data Sheets

DTIC Science & Technology

2017-07-25

Department of Agriculture (USDA) PLANTS Database (http://plants.usda.gov/index.html). The ADS use soil indicators from the National Resources Conservation...of Agriculture - Natural Resources Conservation Service (USDA-NRCS). 2006. Land Resource Regions and Major Land Resource Areas of the United States...the Caribbean, and the Pacific Basin. U.S. Department of Agriculture Handbook 296. Washington DC. United States Department of Agriculture - Natural

H2USA: Siting Refueling Stations in the Northeast

DOE Office of Scientific and Technical Information (OSTI.GOV)

Melaina, Marc W; Muratori, Matteo; Zuboy, Jarett

2017-11-01

To achieve cost-effective deployment of both fuel cell electric vehicles (FCEVs) and hydrogen stations, the number of vehicles and public stations must grow together in areas of highest demand. This fact sheet introduces two advanced modeling tools and presents preliminary analysis of the hydrogen refueling station locations needed to support early consumer demand for FCEVs in the Northeast United States. United States.

Lightweight Solar Photovoltaic Blankets

NASA Technical Reports Server (NTRS)

Ceragioli, R.; Himmler, R.; Nath, P.; Vogeli, C.; Guha, S.

1995-01-01

Lightweight, flexible sheets containing arrays of stacked solar photovoltaic cells developed to supply electric power aboard spacecraft. Solar batteries satisfying stringent requirements for operation in outer space also adaptable to terrestrial environment. Attractive for use as long-lived, portable photovoltaic power sources. Cells based on amorphous silicon which offers potential for order-of-magnitude increases in power per unit weight, power per unit volume, and endurance in presence of ionizing radiation.

5. INDUSTRIAL PIPING SYSTEM FOR 500 H.P. LLEWELLYN BOILER, ADDITION ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

5. INDUSTRIAL PIPING SYSTEM FOR 500 H.P. LLEWELLYN BOILER, ADDITION TO POWER HOUSE. United Engineering Company Ltd., Alameda Shipyard. John Hudspeth, architect, foot of Main Street, Alameda, California. Sheet M1. Plan no. 10,551. Scale 1/4 inch to the foot. June 1, 1945. pencil on vellum - United Engineering Company Shipyard, Boiler House, 2900 Main Street, Alameda, Alameda County, CA

Biogas Potential in the United States (Fact Sheet)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

2013-10-01

Biogas has received increased attention as an alternative energy source in the United States. The factsheet provides information about the biogas (methane) potential from various sources in the country (by county and state) and estimates the power generation and transportation fuels production (renewable natural gas) potential from these biogas sources. It provides valuable information to the industry, academia and policy makers in support of their future decisions.

Geologic map of the Sunnymead 7.5' quadrangle, Riverside County, California

USGS Publications Warehouse

Morton, Douglas M.; Matti, Jonathan C.

2001-01-01

a. This Readme; includes in Appendix I, data contained in sun_met.txt b. The same graphic as plotted in 2 above. Test plots have not produced 1:24,000-scale map sheets. Adobe Acrobat page size setting influences map scale. The Correlation of Map Units and Description of Map Units is in the editorial format of USGS Geologic Investigations Series (I-series) maps but has not been edited to comply with I-map standards. Within the geologic map data package, map units are identified by standard geologic map criteria such as formation-name, age, and lithology. Where known, grain size is indicated on the map by a subscripted letter or letters following the unit symbols as follows: lg, large boulders; b, boulder; g, gravel; a, arenaceous; s, silt; c, clay; e.g. Qyfa is a predominantly young alluvial fan deposit that is arenaceous. Multiple letters are used for more specific identification or for mixed units, e.g., Qfysa is a silty sand. In some cases, mixed units are indicated by a compound symbol; e.g., Qyf2sc. Marine deposits are in part overlain by local, mostly alluvial fan, deposits and are labeled Qomf. Grain size follows f. Even though this is an Open-File Report and includes the standard USGS Open-File disclaimer, the report closely adheres to the stratigraphic nomenclature of the U.S. Geological Survey. Descriptions of units can be obtained by viewing or plotting the .pdf file (3b above) or plotting the postscript file (2 above).

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Rubing, E-mail: zrb86411680@126.com; Zhang, Yaoyao; Liu, Qiang

TiAl/Nb and TiAl/NiCoCrAl laminate composite sheets with a thickness of 0.4–0.6 mm and dimensions of 150 mm × 100 mm were successfully fabricated by electron beam physical vapor deposition. The microstructures of the sheets were examined, and their mechanical properties were compared with those of TiAl monolithic sheet produced by electron beam physical vapor deposition. Tensile testing was performed at room temperature and 750 °C, and the fracture surfaces were examined by scanning electron microscopy. Among the three microlaminate sheets, the TiAl/NiCoCrAl micro-laminate sheet had the best comprehensive properties at room temperature, and the TiAl/Nb micro-laminate sheet showed the idealmore » high-temperature strength and plasticity at 750 °C. The result was discussed in terms of metal strengthening mechanism. - Highlights: • TiAl-based multilayer foils was fabricated successfully by using EB-PVD method; • The tensile properties and micro-fracture morphologies of the sheet were investigated; • The deformation behavior of the multilayer foils was discussed.« less

Dynamics of a radially expanding liquid sheet: Experiments

NASA Astrophysics Data System (ADS)

Majumdar, Nayanika; Tirumkudulu, Mahesh

2017-11-01

A recent theory predicts that sinuous waves generated at the center of a radially expanding liquid sheet grow spatially even in absence of a surrounding gas phase. Unlike flat liquid sheets, the thickness of a radially expanding liquid sheet varies inversely with distance from the center of the sheet. To test the predictions of the theory, experiments were carried out on a horizontal, radially expanding liquid sheet formed by collision of a single jet on a solid impactor. The latter was placed on a speaker-vibrator with controlled amplitude and frequency. The growth of sinuous waves was determined by measuring the wave surface inclination angle using reflected laser light under both atmospheric and sub-atmospheric pressure conditions. It is shown that the measured growth rate matches with the predictions of the theory over a large range of Weber numbers for both pressure conditions suggesting that the thinning of the liquid sheet plays a dominant role in setting the growth rate of sinuous waves with minimal influence of the surrounding gas phase on its dynamics. IIT Bombay.

Cholera Fact Sheet

MedlinePlus

... of more than 50 partners active in cholera control globally, including academic institutions, non-governmental organisations and United Nations agencies. Through the GTFCC and with support from donors, WHO works to: promote the design and implementation of global strategies to contribute to ...

Improved perception of communication and compliance with a revised, intensive care unit-specific bedside communication sheet.

PubMed

Aponte-Patel, Linda; Sen, Anita

2015-01-01

Although many pediatric intensive care units (PICUs) use beside communication sheets (BCSs) to highlight daily goals, the optimal format is unknown. A site-specific BCS could improve both PICU communication and compliance completing the BCS. Via written survey, PICU staff at an academic children's hospital provided recommendations for improving and revising an existing BCS. Pre- and post-BCS revision, PICU staff were polled regarding PICU communication and BCS effectiveness, and daily compliance for completing the BCS was monitored. After implementation of the revised BCS, staff reporting "excellent" or "very good" day-to-day communication within the PICU increased from 57% to 77% (P = .02). Compliance for completing the BCS also increased significantly (75% vs 83%, P = .03). Introduction of a focused and concise BCS tailored to a specific PICU leads to improved perceptions of communication by PICU staff and increased compliance completing the daily BCS. © The Author(s) 2014.

EnviroAtlas - Recreation, Culture, and Aesthetics Metrics for Conterminous United States

EPA Pesticide Factsheets

This EnviroAtlas web service supports research and online mapping activities related to EnviroAtlas (https://www.epa.gov/enviroatlas). The Recreation, Culture, and Aesthetics category in this web service includes layers illustrating the ecosystems and natural resources that provide inherent cultural and aesthetic value or recreation opportunity, the need or demand for these amenities, the impacts associated with their presence and accessibility, and factors that place stress on the natural environment's capability to provide these benefits. EnviroAtlas allows the user to interact with a web-based, easy-to-use, mapping application to view and analyze multiple ecosystem services for the conterminous United States. Additional descriptive information about each attribute in this web service is located within each web service layer (see Full Metadata hyperlink) or can be found in its associated EnviroAtlas Fact Sheet (https://www.epa.gov/enviroatlas/enviroatlas-fact-sheets).

Finite Element Development and Specifications of a Patched, Recessed Nomex Core Honeycomb Panel for Increased Sound Transmission Loss

NASA Technical Reports Server (NTRS)

Grosveld, Ferdinand W.

2007-01-01

This informal report summarizes the development and the design specifications of a recessed nomex core honeycomb panel in fulfillment of the deliverable in Task Order 13RBE, Revision 10, Subtask 17. The honeycomb panel, with 0.020-inch thick aluminum face sheets, has 0.016-inch thick aluminum patches applied to twenty-five, 6 by 6 inch, quarter inch thick recessed cores. A 10 dB higher transmission loss over the frequency range 250 - 1000 Hz was predicted by a MSC/NASTRAN finite element model when compared with the transmission loss of the base nomex core honeycomb panel. The static displacement, due to a unit force applied at either the core or recessed core area, was of the same order of magnitude as the static displacement of the base honeycomb panel when exposed to the same unit force. The mass of the new honeycomb design is 5.1% more than the base honeycomb panel. A physical model was constructed and is being tested.

Bending Tests of Circular Cylinders of Corrugated Aluminum-alloy Sheet

NASA Technical Reports Server (NTRS)

Buckwalter, John C; Reed, Warren D; Niles, Alfred S

1937-01-01

Bending tests were made of two circular cylinders of corrugated aluminum-alloy sheet. In each test failure occurred by bending of the corrugations in a plane normal to the skin. It was found, after analysis of the effect of short end bays, that the computed stress on the extreme fiber of a corrugated cylinder is in excess of that for a flat panel of the same basic pattern and panel length tested as a pin-ended column. It is concluded that this increased strength was due to the effects of curvature of the pitch line. It is also concluded from the tests that light bulkheads closely spaced strengthen corrugated cylinders very materially.

Design and Implementation of a Wireless Sensor Network of GPS-enabled Seismic Sensors for the Study of Glaciers and Ice Sheets

NASA Astrophysics Data System (ADS)

Bilen, S. G.; Anandakrishnan, S.; Urbina, J. V.

2012-12-01

In an effort to provide new and improved geophysical sensing capabilities for the study of ice sheets in Antarctica and Greenland, or to study mountain glaciers, we are developing a network of wirelessly interconnected seismic and GPS sensor nodes (called "geoPebbles"), with the primary objective of making such instruments more capable and cost effective. We describe our design methodology, which has enabled us to develop these state-of-the art sensors using commercial-off-the-shelf hardware combined with custom-designed hardware and software. Each geoPebble is a self-contained, wirelessly connected sensor for collecting seismic measurements and position information. Each node is built around a three-component seismic recorder, which includes an amplifier, filter, and 24-bit analog-to-digital card that can sample up to 10 kHz. Each unit also includes a microphone channel to record the ground-coupled airwave. The timing for each node is available through a carrier-phase measurement of the L1 GPS signal at an absolute accuracy of better than a microsecond. Each geoPebble includes 16 GB of solid-state storage, wireless communications capability to a central supervisory unit, and auxiliary measurements capability (up to eight 10-bit channels at low sample rates). We will report on current efforts to test this new instrument and how we are addressing the challenges imposed by the extreme weather conditions on the Antarctic continent. After fully validating its operational conditions, the geoPebble system will be available for NSF-sponsored glaciology research projects. Geophysical experiments in the polar region are logistically difficult. With the geoPebble system, the cost of doing today's experiments (low-resolution, 2D) will be significantly reduced, and the cost and feasibility of doing tomorrow's experiments (integrated seismic, positioning, 3D, etc.) will be reasonable. Sketch of an experiment with geoPebbles scattered on the surface of the ice sheet. The seismic source can move through the array. The SQC node communicates with all the elements in the array.

Application of image processing technology to problems in manuscript encapsulation. [Codex Hammer

NASA Technical Reports Server (NTRS)

Glackin, D. L.; Korsmo, E. P.

1983-01-01

The long term effects of encapsulation individual sheets of the Codex Hammer were investigated. The manuscript was simulated with similar sheets of paper which were photographed under repeatable raking light conditions to enhance their surface texture, encapsulated in plexiglas, cycled in an environmental test chamber, and rephotographed at selected intervals. The film images were digitized, contrast enhanced, geometrically registered, and apodized. An FFT analysis of a control sheet and two experimental sheets indicates no micro-burnishing, but reveals that the ""mesoscale'' deformations with sizes 8mm are degrading monotonically, which is of no concern. Difference image analysis indicates that the sheets were increasingly stressed with time and that the plexiglas did not provide a sufficient environmental barrier under the simulation conditions. The relationship of these results to the Codex itself is to be determined.

Developing an experimental case in aluminium foils 1100 to determine the maximum angle of formability in a piece by Dieless-SPIF process

NASA Astrophysics Data System (ADS)

Gabriel, Paramo; Adrian, Benitez

2014-07-01

Incremental sheet forming by the method of single point incremental forming Dieless-SPIF, is a widely studied process, experimented and developed in countries with high manufacturing technologies, with friendly costs when the productive configuration in a productivity system is based in small production batches. United states, United kingdom and France lead this type of studies and cases, developing various proof with experimental geometries, different from the national environment such as Colombia, Bolivia, Chile, Ecuador and Peru where this process where discretely studied. Previously mentioned, it pretends develop an experimental case of a particular geometry, identifying the maximum formability angle of material permissible for the forming of a piece in one pass, the analysis of forming limit curve (FLC), with the objective to emphasizes in this innovative method based in CAD-CAM technologies, compare with other analogous process of deformation sheet metal like embossing, take correct decisions about the viability and applicability of this process (Dieless) in a particular industrial piece, which responses to the necessities of productive configurations mentioned and be highly taken like a manufacturing alternative to the other conventional process of forming sheet metal like embossing, for systems with slow batches production.

Lateral dimension-dependent antibacterial activity of graphene oxide sheets.

PubMed

Liu, Shaobin; Hu, Ming; Zeng, Tingying Helen; Wu, Ran; Jiang, Rongrong; Wei, Jun; Wang, Liang; Kong, Jing; Chen, Yuan

2012-08-21

Graphene oxide (GO) is a promising precursor to produce graphene-family nanomaterials for various applications. Their potential health and environmental impacts need a good understanding of their cellular interactions. Many factors may influence their biological interactions with cells, and the lateral dimension of GO sheets is one of the most relevant material properties. In this study, a model bacterium, Escherichia coli ( E. coli ), was used to evaluate the antibacterial activity of well-dispersed GO sheets, whose lateral size differs by more than 100 times. Our results show that the antibacterial activity of GO sheets toward E. coli cells is lateral size dependent. Larger GO sheets show stronger antibacterial activity than do smaller ones, and they have different time- and concentration-dependent antibacterial activities. Large GO sheets lead to most cell loss after 1 h incubation, and their concentration strongly influences antibacterial activity at relative low concentration (<10 μg/mL). In contrast, when incubating with small GO sheets up to 4 h, the inactivation rate of E. coli cells continues increasing. The increase of small GO sheet concentration also results in persistent increases in their antibacterial activity. In this study, GO sheets with different lateral sizes are all well dispersed, and their oxidation capacity toward glutathione is similar, consistent with X-ray photoelectron spectroscopy and ultraviolet-visible absorption spectroscopy results. This suggests the lateral size-dependent antibacterial activity of GO sheets is caused by neither their aggregation states, nor oxidation capacity. Atomic force microscope analysis of GO sheets and cells shows that GO sheets interact strongly with cells. Large GO sheets more easily cover cells, and cells cannot proliferate once fully covered, resulting in the cell viability loss observed in the followed colony counting test. In contrast, small GO sheets adhere to the bacterial surfaces, which cannot effectively isolate cells from environment. This study highlights the importance of tailoring the lateral dimension of GO sheets to optimize the application potential with minimal risks for environmental health and safety.

Building the oceanic crust: Insights on volcanic emplacement processes at the hotspot-influenced Galápagos Spreading Center, 92°W

NASA Astrophysics Data System (ADS)

McClinton, J. T.; White, S. M.; Colman, A.; Sinton, J. M.

2011-12-01

The Galápagos Spreading Center (GSC) displays a range of axial morphology due to increased magma supply from the adjacent Galápagos mantle plume. Over 30 years of scientific exploration has also documented the associated variations in volcanic terrain, crustal thickness, and geochemistry of erupted basalts, but until recently the fine-scale ("lava flow scale") volcanic features of the GSC had not been investigated. Using the Alvin submersible and aided by near-bottom photographic surveys by TowCam and sub-meter-scale sonar surveys by AUV Sentry, we mapped and sampled 12 individual eruptive units covering ~16km2 of seafloor on the ridge axis of the GSC at 92°W. Variations in AUV Sentry bathymetry and DSL-120A backscatter enabled us to characterize the fine-scale surface morphology within each eruptive unit. Lava flow morphologies within each unit were identified using a neuro-fuzzy classifier which assigns pixels as pillows, lobates, sheets, or fissures by using attributes derived from high-resolution sonar bathymetry and backscatter (McClinton et al., submitted PE&RS). An accuracy assessment indicates approximately 90% agreement between the lava morphology map and an independent set of visual observations. The result of this classification effort is that we are able to quantitatively examine the spatial distribution of lava flow morphology as it relates to the emplacement of lava flows within each eruptive unit at a mid-ocean ridge. Preliminary analyses show that a large, segment-centered volcanic cone which straddles the axial summit graben (the "Empanada") is constructed mostly of pillow lavas, while volcanism in the rifted center of the cone consists of lobate and sheet flows. Conversely, along the rest of the segment, on-axis eruptions consist mainly of pillow lava with most sheet and lobate flows found outside of a small axial summit graben. At least some of these sheet flows are fed by lava channels, suggesting emplacement over distances up to 1km, while pillow lava within the summit graben form low mounds; we speculate that eruption effusion rates decreased over the eruptive episode, producing changes in lava morphology within the larger eruptive units. Many axial mounds are also cut by the graben faults. The relatively young appearance of the lava surfaces at 92°W argues for a close relationship between volcanism and graben faulting on this part of the ridge.

Follicular contact dermatitis due to coloured permanent-pressed sheets

PubMed Central

Panaccio, François; Montgomery, D. C.; Adam, J. E.

1973-01-01

A delayed hypersensitivity type of allergic contact dermatitis was observed following exposure to certain brands of 50% cotton, 50% polyester coloured permanent-pressed sheets produced by a particular manufacturer. The dermatitis presented as an extremely pruritic follicular eczema of the body and vesicular edema of the ears and face. Patch testing excluded formalin as the allergen but suggested permanent-pressing chemicals as a possibility. Several washings of the sheets did not prevent the development of the dermatitis. The removal of sheets did not immediately result in improvement: the condition could persist for up to eight weeks after their discontinuance. ImagesFIG. 1FIG. 2FIG. 3FIG. 4FIG. 5 PMID:4268628

Self-consistent current sheet structures in the quiet-time magnetotail

NASA Technical Reports Server (NTRS)

Holland, Daniel L.; Chen, James

1993-01-01

The structure of the quiet-time magnetotail is studied using a test particle simulation. Vlasov equilibria are obtained in the regime where v(D) = E(y) c/B(z) is much less than the ion thermal velocity and are self-consistent in that the current and magnetic field satisfy Ampere's law. Force balance between the plasma and magnetic field is satisfied everywhere. The global structure of the current sheet is found to be critically dependent on the source distribution function. The pressure tensor is nondiagonal in the current sheet with anisotropic temperature. A kinetic mechanism is proposed whereby changes in the source distribution results in a thinning of the current sheet.

Boron supercapacitors

DOE PAGES

Zhan, Cheng; Zhang, Pengfei; Dai, Sheng; ...

2016-11-16

Supercapacitors based on the electric double-layer mechanism use porous carbons or graphene as electrodes. To move beyond this paradigm, we propose boron supercapacitors to leverage two-dimensional (2D) boron sheets’ metallicity and low weight. Six 2D boron sheets from both previous theoretical design and experimental growth are chosen as test electrodes. By applying joint density functional theory (JDFT) to the electrode–electrolyte system, we examine how the 2D boron sheets charge up against applied potential. JDFT predicts that these 2D boron sheets exhibit specific capacitance on the order of 400 F/g, about four times that of graphene. As a result, our workmore » suggests that 2D boron sheets are promising electrodes for supercapacitor applications.« less

Boron supercapacitors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhan, Cheng; Zhang, Pengfei; Dai, Sheng

Supercapacitors based on the electric double-layer mechanism use porous carbons or graphene as electrodes. To move beyond this paradigm, we propose boron supercapacitors to leverage two-dimensional (2D) boron sheets’ metallicity and low weight. Six 2D boron sheets from both previous theoretical design and experimental growth are chosen as test electrodes. By applying joint density functional theory (JDFT) to the electrode–electrolyte system, we examine how the 2D boron sheets charge up against applied potential. JDFT predicts that these 2D boron sheets exhibit specific capacitance on the order of 400 F/g, about four times that of graphene. As a result, our workmore » suggests that 2D boron sheets are promising electrodes for supercapacitor applications.« less

Change in oligosaccharides during processing of soybean sheet.

PubMed

Wang, Qiushuang; Ke, Leqin; Yang, Dongmei; Bao, Bili; Jiang, Jianmei; Ying, Tiejin

2007-01-01

Oligosaccharides have been credited with many health-promoting functions, which had been identified in many clinical studies, such as promoting the growth of Bifidobacterium in human intestine and balance of intestinal bacteria, modulating the immune response, inhibition of cancer and tumor, stimulation of mineral absorption. In this study the effect of processing unit operations on the levels of soybean oligosaccharides during production of soybean sheet were investigated. The concentrations of oligosaccharide in initial raw soybean were: sucrose 43.05 g/kg, raffinose 7.52 g/kg and stachyose 41.32 g/kg (in dry matter). Oligosaccharide losses in the soaking water, in the first filtrating stage, in the second filtrating stage and finally in the sheet formation stage were 0.68, 10.3, 8.15 and 47.22 g/kg (initial dry soybean) respectively, representing 0.74, 11.21, 8.87 and 51.39% of the total oligosaccharides present in the initial soybeans. The recovery of oligosaccharides in the final soybean sheet from the initial soybean was 27.92%. The loss of soybean oligosaccharides in different processing stages, especially in the by-product, the sweet slurry, was considerable. The loss of oligosaccharides was mainly associated with water/matter removal in production process. The analysis of loss profile implied possible ways to improve the technology for production of oligosaccharides-enriched soy-sheets.

Programmable matter by folding

PubMed Central

Hawkes, E.; An, B.; Benbernou, N. M.; Tanaka, H.; Kim, S.; Demaine, E. D.; Rus, D.; Wood, R. J.

2010-01-01

Programmable matter is a material whose properties can be programmed to achieve specific shapes or stiffnesses upon command. This concept requires constituent elements to interact and rearrange intelligently in order to meet the goal. This paper considers achieving programmable sheets that can form themselves in different shapes autonomously by folding. Past approaches to creating transforming machines have been limited by the small feature sizes, the large number of components, and the associated complexity of communication among the units. We seek to mitigate these difficulties through the unique concept of self-folding origami with universal crease patterns. This approach exploits a single sheet composed of interconnected triangular sections. The sheet is able to fold into a set of predetermined shapes using embedded actuation. To implement this self-folding origami concept, we have developed a scalable end-to-end planning and fabrication process. Given a set of desired objects, the system computes an optimized design for a single sheet and multiple controllers to achieve each of the desired objects. The material, called programmable matter by folding, is an example of a system capable of achieving multiple shapes for multiple functions. PMID:20616049

Programmable matter by folding.

PubMed

Hawkes, E; An, B; Benbernou, N M; Tanaka, H; Kim, S; Demaine, E D; Rus, D; Wood, R J

2010-07-13

Programmable matter is a material whose properties can be programmed to achieve specific shapes or stiffnesses upon command. This concept requires constituent elements to interact and rearrange intelligently in order to meet the goal. This paper considers achieving programmable sheets that can form themselves in different shapes autonomously by folding. Past approaches to creating transforming machines have been limited by the small feature sizes, the large number of components, and the associated complexity of communication among the units. We seek to mitigate these difficulties through the unique concept of self-folding origami with universal crease patterns. This approach exploits a single sheet composed of interconnected triangular sections. The sheet is able to fold into a set of predetermined shapes using embedded actuation. To implement this self-folding origami concept, we have developed a scalable end-to-end planning and fabrication process. Given a set of desired objects, the system computes an optimized design for a single sheet and multiple controllers to achieve each of the desired objects. The material, called programmable matter by folding, is an example of a system capable of achieving multiple shapes for multiple functions.

Frustules to fragments, diatoms to dust: How degradation of microfossil shape and microstructures can teach us how ice sheets work

USGS Publications Warehouse

Scherer, R.P.; Sjunneskog, C.M.; Iverson, M.R.; Hooyer, T.S.

2005-01-01

In a laboratory experiment we investigated micro- and nanoscale changes in fossil diatom valves and in the texture of diatomaceous sediments that result from ice sheet overburden and subglacial shearing. Our experiment included compression and shearing of Antarctic diatom-rich sediments in a ring shear device and comparison of experimental samples with natural glacial sediments from the Antarctic continental shelf. The purpose of the experiment is to establish objective criteria for analyzing subglacial processes and interpreting the origin of glacial-geologic features on the Antarctic continental shelf. We find distinct changes resulting from different glacial settings, with respect to whole diatom frustules, diatom micromorphology, and microtextural properties of sedimentary units. By providing constraints on subglacial shearing, these observations of genetically controlled micro- and nanoscale diatom structures and architecture are contributing to the understanding of large-scale glacial processes, aiding the development of models of modern ice sheet processes, and guiding interpretation of past ice sheet configurations. Copyright ?? 2005 American Scientific Publishers. All rights reserved.

Drilling Machines: Vocational Machine Shop.

ERIC Educational Resources Information Center

Thomas, John C.

The lessons and supportive information in this field tested instructional block provide a guide for teachers in developing a machine shop course of study in drilling. The document is comprised of operation sheets, information sheets, and transparency masters for 23 lessons. Each lesson plan includes a performance objective, material and tools,…

LOFT. Containment and service building (TAN650). Room number schedule, sheet ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

LOFT. Containment and service building (TAN-650). Room number schedule, sheet 2 of 2. Kaiser engineers 6413-11-STEP/LOFT-650-A-XX. Date: October 1969. INEEL index code no. 036-650-00-486-122228 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

Improving patient handover between teams using a business improvement model: PDSA cycle.

PubMed

Luther, Vishal; Hammersley, Daniel; Chekairi, Ahmed

2014-01-01

Medical admission units are continuously under pressure to move patients off the unit to outlying medical wards and allow for new admissions. In a typical district general hospital, doctors working in these medical wards reported that, on average, three patients each week arrived from the medical admission unit before any handover was received, and a further two patients arrived without any handover at all. A quality improvement project was therefore conducted using a 'Plan, Do, Study, Act' cycle model for improvement to address this issue. P - Plan: as there was no framework to support doctors with handover, a series of standard handover procedures were designed. D - Do: the procedures were disseminated to all staff, and championed by key stakeholders, including the clinical director and matron of the medical admission unit. S - STUDY: Measurements were repeated 3 months later and showed no change in the primary end points. A - ACT: The post take ward round sheet was redesigned, creating a checkbox for a medical admission unit doctor to document that handover had occurred. Nursing staff were prohibited from moving the patient off the ward until this had been completed. This later evolved into a separate handover sheet. Six months later, a repeat study revealed that only one patient each week was arriving before or without a verbal handover. Using a 'Plan, Do, Study, Act' business improvement tool helped to improve patient care.

Evaluation of electrical test conditions in MIL-M-38510 slash sheets

NASA Astrophysics Data System (ADS)

Sandgren, K.

1980-08-01

Adequacy of MIL-M-38510 slash sheet requirements for electrical test conditions in an automated test environment were evaluated. Military temperature range commercial devices of 13 types from 6 manufacturers were purchased. Software for testing these devices and for varying the test conditions was written for the Tektronix S-3260 test system. The devices were tested to evaluate the effects of pin-condition settling time, measurement sequence of the same and different D-C parameters, temperature sequence, differently defined temperature ambients, variable measurement conditions, sequence of time measurements, pin-application sequence, and undesignated pin condition ambiguity. An alternative to current tri-state enable and disable time measurements is proposed; S-3260 'open' and 'ground' conditions are characterized; and suggestions for changes in MIL-M-38510 slash sheet specifications and MIL-STD-883 test methods are proposed, both to correct errors and ambiguities and to facilitate the gathering of repeatable data on automated test equipment. Data obtained showed no sensitivity to measurement or temperature sequence nor to temperature ambient, provided that test times were not excessive. V sub ICP tests and some low current measurements required allowance for a pin condition settling time because of the test system speed. Some pin condition application sequences yielded incorrect measurements. Undefined terminal conditions of output pins were found to affect I sub OS and propagation delay time measurements. Truth table test results varied with test frequency and V sub IL for low-power Schottky devices.

Improving Building Energy Simulation Programs Through Diagnostic Testing (Fact Sheet)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

2012-02-01

New test procedure evaluates quality and accuracy of energy analysis tools for the residential building retrofit market. Reducing the energy use of existing homes in the United States offers significant energy-saving opportunities, which can be identified through building simulation software tools that calculate optimal packages of efficiency measures. To improve the accuracy of energy analysis for residential buildings, the National Renewable Energy Laboratory's (NREL) Buildings Research team developed the Building Energy Simulation Test for Existing Homes (BESTEST-EX), a method for diagnosing and correcting errors in building energy audit software and calibration procedures. BESTEST-EX consists of building physics and utility billmore » calibration test cases, which software developers can use to compare their tools simulation findings to reference results generated with state-of-the-art simulation tools. Overall, the BESTEST-EX methodology: (1) Tests software predictions of retrofit energy savings in existing homes; (2) Ensures building physics calculations and utility bill calibration procedures perform to a minimum standard; and (3) Quantifies impacts of uncertainties in input audit data and occupant behavior. BESTEST-EX is helping software developers identify and correct bugs in their software, as well as develop and test utility bill calibration procedures.« less

EPA Analysis of FracFocus 1 Data Fact Sheet

EPA Pesticide Factsheets

The EPA analyzed over two years of data from the FracFocus Chemical Disclosure Registry 1.0 to better understand the chemicals and water used to hydraulically fracture oil and gas production wells in the United States.

News Releases, Press Releases, Tip Sheet Statements

Science.gov Websites

United States Census Bureau Topics Population Latest Information Age and Sex Ancestry Children Mobility Population Estimates Population Projections Race Veterans Economy Latest Information Portal Other Economic Programs Business Latest Information Business Characteristics Classification Codes

India Solar Resource Data: Enhanced Data for Accelerated Deployment (Fact Sheet)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

Identifying potential locations for solar photovoltaic (PV) and concentrating solar power (CSP) projects requires an understanding of the underlying solar resource. Under a bilateral partnership between the United States and India - the U.S.-India Energy Dialogue - the National Renewable Energy Laboratory has updated Indian solar data and maps using data provided by the Ministry of New and Renewable Energy (MNRE) and the National Institute for Solar Energy (NISE). This fact sheet overviews the updated maps and data, which help identify high-quality solar energy projects. This can help accelerate the deployment of solar energy in India.

Static renewal tests using Anodonta imbecillis (freshwater mussels). Anodonta imbecillis QA test 4, Clinch River-Environmental Restoration Program (CR-ERP)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Simbeck, D.J.

1994-12-31

Toxicity testing of split whole sediment samples using juvenile freshwater mussels (Anodonta imbecillis) was conducted by TVA to provide a quality assurance mechanism for test organisms quality and overall performance of the test being conducted by CR-ERP personnel as part of the CR-ERP biomonitoring study of Clinch River sediments. Testing of sediment samples collected September 8 from Poplar Creek Miles 6.0 and 1.0 was conducted September 13--22, 1994. Results from this test showed no toxicity (survival effects) to fresh-water mussels during a 9-day exposure to the sediments. Attachments to this report include: Chain of custody form -- original; Toxicity testmore » bench sheets; Ammonia analysis request and results; and Meter calibration log sheets.« less

Packing and deploying Soft Origami to and from cylindrical volumes with application to automotive airbags

PubMed Central

Nelson, Todd G.; Zimmerman, Trent K.; Fernelius, Janette D.; Magleby, Spencer P.; Howell, Larry L.

2016-01-01

Packing soft-sheet materials of approximately zero bending stiffness using Soft Origami (origami patterns applied to soft-sheet materials) into cylindrical volumes and their deployment via mechanisms or internal pressure (inflation) is of interest in fields including automobile airbags, deployable heart stents, inflatable space habitats, and dirigible and parachute packing. This paper explores twofold patterns, the ‘flasher’ and the ‘inverted-cone fold’, for packing soft-sheet materials into cylindrical volumes. Two initial packing methods and mechanisms are examined for each of the flasher and inverted-cone fold patterns. An application to driver’s side automobile airbags is performed, and deployment tests are completed to compare the influence of packing method and origami pattern on deployment performance. Following deployment tests, two additional packing methods for the inverted-cone fold pattern are explored and applied to automobile airbags. It is shown that modifying the packing method (using different methods to impose the same base pattern on the soft-sheet material) can lead to different deployment performance. In total, two origami patterns and six packing methods are examined, and the benefits of using Soft Origami patterns and packing methods are discussed. Soft Origami is presented as a viable method for efficiently packing soft-sheet materials into cylindrical volumes. PMID:27703707

Packing and deploying Soft Origami to and from cylindrical volumes with application to automotive airbags

NASA Astrophysics Data System (ADS)

Bruton, Jared T.; Nelson, Todd G.; Zimmerman, Trent K.; Fernelius, Janette D.; Magleby, Spencer P.; Howell, Larry L.

2016-09-01

Packing soft-sheet materials of approximately zero bending stiffness using Soft Origami (origami patterns applied to soft-sheet materials) into cylindrical volumes and their deployment via mechanisms or internal pressure (inflation) is of interest in fields including automobile airbags, deployable heart stents, inflatable space habitats, and dirigible and parachute packing. This paper explores twofold patterns, the `flasher' and the `inverted-cone fold', for packing soft-sheet materials into cylindrical volumes. Two initial packing methods and mechanisms are examined for each of the flasher and inverted-cone fold patterns. An application to driver's side automobile airbags is performed, and deployment tests are completed to compare the influence of packing method and origami pattern on deployment performance. Following deployment tests, two additional packing methods for the inverted-cone fold pattern are explored and applied to automobile airbags. It is shown that modifying the packing method (using different methods to impose the same base pattern on the soft-sheet material) can lead to different deployment performance. In total, two origami patterns and six packing methods are examined, and the benefits of using Soft Origami patterns and packing methods are discussed. Soft Origami is presented as a viable method for efficiently packing soft-sheet materials into cylindrical volumes.

Packing and deploying Soft Origami to and from cylindrical volumes with application to automotive airbags.

PubMed

Bruton, Jared T; Nelson, Todd G; Zimmerman, Trent K; Fernelius, Janette D; Magleby, Spencer P; Howell, Larry L

2016-09-01

Packing soft-sheet materials of approximately zero bending stiffness using Soft Origami (origami patterns applied to soft-sheet materials) into cylindrical volumes and their deployment via mechanisms or internal pressure (inflation) is of interest in fields including automobile airbags, deployable heart stents, inflatable space habitats, and dirigible and parachute packing. This paper explores twofold patterns, the 'flasher' and the 'inverted-cone fold', for packing soft-sheet materials into cylindrical volumes. Two initial packing methods and mechanisms are examined for each of the flasher and inverted-cone fold patterns. An application to driver's side automobile airbags is performed, and deployment tests are completed to compare the influence of packing method and origami pattern on deployment performance. Following deployment tests, two additional packing methods for the inverted-cone fold pattern are explored and applied to automobile airbags. It is shown that modifying the packing method (using different methods to impose the same base pattern on the soft-sheet material) can lead to different deployment performance. In total, two origami patterns and six packing methods are examined, and the benefits of using Soft Origami patterns and packing methods are discussed. Soft Origami is presented as a viable method for efficiently packing soft-sheet materials into cylindrical volumes.

Experimental characterization and macro-modeling of mechanical strength of multi-sheets and multi-materials spot welds under pure and mixed modes I and II

NASA Astrophysics Data System (ADS)

Chtourou, Rim; Haugou, Gregory; Leconte, Nicolas; Zouari, Bassem; Chaari, Fahmi; Markiewicz, Eric

2015-09-01

Resistance Spot Welding (RSW) of multiple sheets with multiple materials are increasingly realized in the automotive industry. The mechanical strength of such new generation of spot welded assemblies is not that much dealt with. This is true in particular for experiments dedicated to investigate the mechanical strength of spot weld made by multi sheets of different grades, and their macro modeling in structural computations. Indeed, the most published studies are limited to two sheet assemblies. Therefore, in the first part of this work an advanced experimental set-up with a reduced mass is proposed to characterize the quasi-static and dynamic mechanical behavior and rupture of spot weld made by several sheets of different grades. The proposed device is based on Arcan test, the plates contribution in the global response is, thus, reduced. Loading modes I/II are, therefore, combined and well controlled. In the second part a simplified spot weld connector element (macroscopic modeling) is proposed to describe the nonlinear response and rupture of this new generation of spot welded assemblies. The weld connector model involves several parameters to be set. The remaining parameters are finally identified through a reverse engineering approach using mechanical responses of experimental tests presented in the first part of this work.

Testing of Shelter Design and Industrial Hardening Concepts at the MILL RACE Event.

DTIC Science & Technology

1982-01-01

built. The upgrading consisted of the application of 2-in. thick sheets of expanded polystyrene to the exterior of each of the test walls to be upgraded...was covered with 1-in. thick sheets of expanded polystyrene prior to backfilling (Figure 6-4), and the interior was shored, floor to ceiling, with two...deformations in the vault, despite the fact that no structural upgrading options (shores, or roof cover of expanded polystyrene ) were installed. Thus

10. Photographic copy of engineering drawing showing the plumbing layout ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

10. Photographic copy of engineering drawing showing the plumbing layout of Test Stand 'C' Cv Cell, vacuum line, and scrubber-condenser as erected in 1977-78. JPL drawing by VTN Consolidated, Inc. Engineers, Architects, Planners, 2301 Campus Drive, Irvine, California 92664: 'JPL-ETS E-18 (C-Stand Modifications) Flow Diagram,' sheet M-2 (JPL sheet number E18/41-0), September 1, 1977. - Jet Propulsion Laboratory Edwards Facility, Test Stand C, Edwards Air Force Base, Boron, Kern County, CA

9. Photographic copy of engineering drawing showing the mechanical layout ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

9. Photographic copy of engineering drawing showing the mechanical layout of Test Stand 'C' Cv Cell, vacuum line, and scrubber-condenser as erected in 1977-78. JPL drawing by VTN Consolidated, Inc. Engineers, Architects, Planners, 2301 Campus Drive, Irvine, California 92664: 'JPL-ETS E-18 (C-Stand Modifications) Control Elevations & Schematics,' sheet M-5 (JPL sheet number E18/44-0), 1 September 1977. - Jet Propulsion Laboratory Edwards Facility, Test Stand C, Edwards Air Force Base, Boron, Kern County, CA

Distribution and Aggregate Thickness of Salt Deposits of the United States

EPA Pesticide Factsheets

The map shows the distribution and aggregate thickness of salt deposits of the United States. This information is from contour map sheets, scanned and processed for use in a global mineral resource assessment, produced by the U.S. Geological Survey. It is used here to provide a geospatial context to the distribution of rock-salt deposits in the US. It is useful in illustrating sources of chlorides.

Manned maneuvering unit mission definition study. Volume 2: Appendices to the MMU applications analysis

NASA Technical Reports Server (NTRS)

1975-01-01

Information used in identifying representative Manned Maneuvering Unit (MMU) from the many Automated and Sortie Payloads and orbiter subsystems is presented. Representative missions were selected to represent typical MMU applications across all payloads and orbiter subsystems. Data analysis sheets are provided with other applicable information. Calculations used in defining MMU general performance and control requirements to satisfy eleven space missions are included.

Home Economics--A Look--A Job--A Future. A Course of Study at a Pre-Vocational Level for 7th and/or 8th Grade.

ERIC Educational Resources Information Center

Oklahoma City Public School System, OK. Dept. of Home Economics.

Prevocational materials for use at the seventh and/or eighth grade levels are presented in this curriculum guide. Materials cover six areas, each consisting of several instructional units planned for more than one lesson or class period. Each unit includes behavioral objectives, suggested activities for teacher and students, information sheets,…

The Dorsa Argentea Formation and the Noachian-Hesperian climate transition

NASA Astrophysics Data System (ADS)

Scanlon, K. E.; Head, J. W.; Fastook, J. L.; Wordsworth, R. D.

2018-01-01

The Dorsa Argentea Formation (DAF), a set of geomorphologic units covering ∼1.5 million square kilometers in the south circumpolar region of Mars, has been interpreted as the remnants of a large south polar ice sheet that formed near the Noachian-Hesperian boundary and receded in the early Hesperian. Determining the extent and thermal regime of the DAF ice sheet, as well as the mechanism and timing of its recession, can therefore provide insight into the ancient martian climate and the timing of the transition from a presumably thicker CO2 atmosphere to the present climate. We used the Laboratoire de Météorologie Dynamique (LMD) early Mars global climate model (GCM) and the University of Maine Ice Sheet Model (UMISM) glacial flow model to constrain climates allowing development of a south polar ice sheet of DAF-like size and shape. In addition, we modeled basal melting of this ice sheet in amounts and locations consistent with observed glaciofluvial landforms. A large, asymmetric region of ice stability surrounding the south pole is a robust feature of GCM simulations with spin-axis obliquity of 15° or 25° and a 600-1000 mb CO2 atmosphere. The shape results from the large-scale south polar topography of Mars and the strong dependence of surface temperature on altitude under a thicker atmosphere. Of the scenarios considered in this study, the extent of the modeled DAF ice sheet in UMISM simulations most closely matches that of the DAF when the surface water ice inventory of Mars is a ∼137 m global equivalent layer (GEL) and spin-axis obliquity is 15°. In climates warmed only by CO2, significant basal melting does not occur except when the ice inventory is larger than plausible estimates for early Mars. In this case, the extent of the south polar ice sheet is also much larger than that of the DAF, and basal melting is more widespread than observed landforms indicate. When an idealized greenhouse gas warms the surface by at least 20°C near the poles relative to CO2 alone, the stable extent of the ice sheet is less than that of the DAF units, but widespread basal melting occurs, with maxima in the locations where eskers are currently observed. We therefore conclude that warming by a gas other than CO2 alone was necessary to enable the construction of glaciofluvial landforms in the DAF. Previously published crater exposure ages of eskers in the DAF indicate that eskers were being exposed as activity was ceasing in the equatorial valley networks, suggesting that the warming that allowed basal melting at the edges of the DAF ice sheet were broadly contemporaneous with those in which the valley networks were carved. Finally, elevated Tharsis topography is required to produce an ice sheet with the shape of the DAF. Thus, our results are not consistent with the DAF (and the valley networks) forming before the emplacement of Tharsis, as recently suggested.

U-Pb zircon age data for selected sedimentary, metasedimentary, and igneous rocks from northern and central Alaska

USGS Publications Warehouse

Moore, Thomas E.

2014-01-01

Data from two studies are included in this report. The first study, by Dumoulin and others (2013), reported the detrital zircon U-Pb age analysis of a single sample from the Upper Mississippian Ikalukrok unit of the Kuna Formation (table 1). The second study is that of Moore and others (in press), which focuses on the Upper Jurassic and Lower Cretaceous part of the Brookian sequence in the western Brooks Range (17 samples; table 2). For the latter study, samples were analyzed from the following units (1) the Upper Jurassic unit, Jw, of Curtis and others (1984), (2) the Lower Cretaceous Igrarok Hills unit of Moore and others (2002), (3) the Upper Jurassic and Lower Cretaceous Okpikruak Formation, (4) the Lower Cretaceous lower Brookian shale of Mull (1995), (5) the Lower Cretaceous Mount Kelly Graywacke Tongue of the Fortress Mountain Formation, (6) and the upper Lower Cretaceous Nanushuk Formation as redefined by Mull and others (2003). The results for each study are reported in separate Excel files, with individual samples in each study being shown as separate sheets within the files. The analyses of individual zircons are listed separately on the sheet according to the filtering schemes of the study and by the type of mass spectrometer used.

Biomimetic collagen/elastin meshes for ventral hernia repair in a rat model.

PubMed

Minardi, Silvia; Taraballi, Francesca; Wang, Xin; Cabrera, Fernando J; Van Eps, Jeffrey L; Robbins, Andrew B; Sandri, Monica; Moreno, Michael R; Weiner, Bradley K; Tasciotti, Ennio

2017-03-01

Ventral hernia repair remains a major clinical need. Herein, we formulated a type I collagen/elastin crosslinked blend (CollE) for the fabrication of biomimetic meshes for ventral hernia repair. To evaluate the effect of architecture on the performance of the implants, CollE was formulated both as flat sheets (CollE Sheets) and porous scaffolds (CollE Scaffolds). The morphology, hydrophylicity and in vitro degradation were assessed by SEM, water contact angle and differential scanning calorimetry, respectively. The stiffness of the meshes was determined using a constant stretch rate uniaxial tensile test, and compared to that of native tissue. CollE Sheets and Scaffolds were tested in vitro with human bone marrow-derived mesenchymal stem cells (h-BM-MSC), and finally implanted in a rat ventral hernia model. Neovascularization and tissue regeneration within the implants was evaluated at 6weeks, by histology, immunofluorescence, and q-PCR. It was found that CollE Sheets and Scaffolds were not only biomechanically sturdy enough to provide immediate repair of the hernia defect, but also promoted tissue restoration in only 6weeks. In fact, the presence of elastin enhanced the neovascularization in both sheets and scaffolds. Overall, CollE Scaffolds displayed mechanical properties more closely resembling those of native tissue, and induced higher gene expression of the entire marker genes tested, associated with de novo matrix deposition, angiogenesis, adipogenesis and skeletal muscles, compared to CollE Sheets. Altogether, this data suggests that the improved mechanical properties and bioactivity of CollE Sheets and Scaffolds make them valuable candidates for applications of ventral hernia repair. Due to the elevated annual number of ventral hernia repair in the US, the lack of successful grafts, the design of innovative biomimetic meshes has become a prime focus in tissue engineering, to promote the repair of the abdominal wall, avoid recurrence. Our meshes (CollE Sheets and Scaffolds) not only showed promising mechanical performance, but also allowed for an efficient neovascularization, resulting in new adipose and muscle tissue formation within the implant, in only 6weeks. In addition, our meshes allowed for the use of the same surgical procedure utilized in clinical practice, with the commercially available grafts. This study represents a significant step in the design of bioactive acellular off-the-shelf biomimetic meshes for ventral hernia repair. Copyright © 2016 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Sea-level response to abrupt ocean warming of Antarctic ice shelves

NASA Astrophysics Data System (ADS)

Pattyn, Frank

2016-04-01

Antarctica's contribution to global sea-level rise increases steadily. A fundamental question remains whether the ice discharge will lead to marine ice sheet instability (MISI) and collapse of certain sectors of the ice sheet or whether ice loss will increase linearly with the warming trends. Therefore, we employ a newly developed ice sheet model of the Antarctic ice sheet, called f.ETISh (fast Elementary Thermomechanical Ice Sheet model) to simulate ice sheet response to abrupt perturbations in ocean and atmospheric temperature. The f.ETISh model is a vertically integrated hybrid (SSA/SIA) ice sheet model including ice shelves. Although vertically integrated, thermomechanical coupling is ensured through a simplified representation of ice sheet thermodynamics based on an analytical solution of the vertical temperature profile, including strain heating and horizontal advection. The marine boundary is represented by a flux condition either coherent with power-law basal sliding (Pollard & Deconto (2012) based on Schoof (2007)) or according to Coulomb basal friction (Tsai et al., 2015), both taking into account ice-shelf buttressing. Model initialization is based on optimization of the basal friction field. Besides the traditional MISMIP tests, new tests with respect to MISI in plan-view models have been devised. The model is forced with stepwise ocean and atmosphere temperature perturbations. The former is based on a parametrised sub-shelf melt (limited to ice shelves), while the latter is based on present-day mass balance/surface temperature and corrected for elevation changes. Surface melting is introduced using a PDD model. Results show a general linear response in mass loss to ocean warming. Nonlinear response due to MISI occurs under specific conditions and is highly sensitive to the basal conditions near the grounding line, governed by both the initial conditions and the basal sliding/deformation model. The Coulomb friction model leads to significantly higher sensitivity compared to power-law sliding. On longer time scales, West-antarctic inter-basin connections favor nonlinear response.

Pilot randomized trial of a volitional help sheet-based tool to increase leisure time physical activity in breast cancer survivors.

PubMed

Chapman, Janine; Fletcher, Chloe; Flight, Ingrid; Wilson, Carlene

2018-05-16

To develop and test a volitional help sheet-based tool to improve physical activity in breast cancer survivors compared to a standard self-generated implementation intention intervention. Pilot randomized trial conducted online over 3 months. Participants were randomized to an online volitional help sheet (n = 50) or implementation intention (n = 51) intervention. Measures were taken at baseline, 1 and 3 months. The main outcome measure was moderate-strenuous leisure time physical activity. Secondary outcomes were health-related quality of life and mood. Participants exposed to the volitional help sheet and implementation intention interventions showed similar effects after 1 month, with both groups reporting a significant increase in moderate-strenuous physical activity. After 3 months, the initial increase in physical activity was maintained by the volitional help sheet group, but not the implementation intention group. Improvements were also found for negative affect and emotional quality of life. While both interventions show promise in promoting physical activity in breast cancer survivors, the volitional help sheet may be more effective for facilitating lasting change and emotional well-being. Findings suggest that the volitional help sheet may have potential to offer a cost-effective contribution to consumer-led tertiary preventive health. Future research should test these initial findings in a definitive trial. Statement of contribution What is already known on this subject? Physical activity is important for optimizing health in breast cancer survivors. Despite this, physical activity in this cohort remains low. Theory-based strategies are needed to help breast cancer survivors independently manage and maintain regular physical activity over the long term. What does this study add? Online planning interventions can improve physical activity in breast cancer survivors. Volitional help sheets, but not implementation intentions, show sustained effects for 3 months. The intervention shows promise as a potential low-cost addition to long-term survivorship care plans. © 2018 The British Psychological Society.

The study of fix composite panel and steel plates on testing stand

NASA Astrophysics Data System (ADS)

Wróbel, A.; Płaczek, M.; Wachna, M.

2016-08-01

In this paper the practical possibilities of strength verification analysis of composite materials used in the manufacture of selected components of railway wagons are presented. Real laboratory stand for measurements in a scale controlled by PLC controller were made. The study of different types of connections of composite materials with sheet metal is presented. In one of the chapter of this paper principles construction of testing stand with pneumatic cylinder were presented. Mainly checking of displacements and stresses generated on the sheet as a result of pneumatic actuators load for composite boards was carried out. The use of the controller with operating panel allows to easy programming testing cycle. The user can define the force generated by the actuator by change of air pressure in cylinder. Additionally the location of acting cylinders and their jump can be changed by operator. The examination of the volume displacements was done by displacement sensor, and the tensile strain gauge. All parameters are written in CatmanEasy - data acquisition software. This article presents the study of stresses and displacements in the composite plates joined with sheet metal, in summary of this article, the authors compare the obtained results with the computer simulation results in the article: "Simulation of stresses in an innovative combination of composite with sheet".

Preliminary geologic map of the Perris 7.5' quadrangle, Riverside County, California

USGS Publications Warehouse

Morton, Douglas M.; Digital preparation by Bovard, Kelly R.; Alvarez, Rachel M.

2003-01-01

Open-File Report 03-270 contains a digital geologic map database of the Perris 7.5’ quadrangle, Riverside County, California that includes: 1. ARC/INFO (Environmental Systems Research Institute, http://www.esri.com) version 7.2.1 coverages of the various elements of the geologic map. 2. A Postscript file to plot the geologic map on a topographic base, and containing a Correlation of Map Units diagram (CMU), a Description of Map Units (DMU), and an index map. 3. Portable Document Format (.pdf) files of: a. A Readme file b. The same graphic as described in 2 above. Test plots have not produced precise 1:24,000- scale map sheets. Adobe Acrobat page size setting influences map scale. The Correlation of Map Units and Description of Map Units is in the editorial format of USGS Geologic Investigations Series (I-series) maps but has not been edited to comply with I-map standards. Within the geologic map data package, map units are identified by standard geologic map criteria such as formationname, age, and lithology. Where known, grain size is indicated on the map by a subscripted letter or letters following the unit symbols as follows: lg, large boulders; b, boulder; g, gravel; a, arenaceous; s, silt; c, clay; e.g. Qyfa is a predominantly young alluvial fan deposit that is arenaceous. Multiple letters are used for more specific identification or for mixed units, e.g., Qfysa is a silty sand. In some cases, mixed units are indicated by a compound symbol; e.g., Qyf2sc.

Delaware River Basin

USGS Publications Warehouse

Fischer, Jeffrey M.

1999-01-01

Assessing the quality of water in every location of the Nation would not be practical. Therefore, NAWQA investigations are conducted within 59 selected areas called study units (fig. 1). These study units encompass important river and aquifer systems in the United States and represent the diverse geographic, waterresource, land-use, and water-use characteristics of the Nation. The Delaware River Basin is one of 15 study units in which work began in 1996. Water-quality sampling in the study unit will begin in 1999. This fact sheet provides a brief overview of the NAWQA program, describes the Delaware River Basin study unit, identifies the major water-quality issues in the basin, and documents the plan of study that will be followed during the study-unit investigation.