Evaluation of electrical test conditions in MIL-M-38510 slash sheets

NASA Astrophysics Data System (ADS)

Sandgren, K.

1980-08-01

Adequacy of MIL-M-38510 slash sheet requirements for electrical test conditions in an automated test environment were evaluated. Military temperature range commercial devices of 13 types from 6 manufacturers were purchased. Software for testing these devices and for varying the test conditions was written for the Tektronix S-3260 test system. The devices were tested to evaluate the effects of pin-condition settling time, measurement sequence of the same and different D-C parameters, temperature sequence, differently defined temperature ambients, variable measurement conditions, sequence of time measurements, pin-application sequence, and undesignated pin condition ambiguity. An alternative to current tri-state enable and disable time measurements is proposed; S-3260 'open' and 'ground' conditions are characterized; and suggestions for changes in MIL-M-38510 slash sheet specifications and MIL-STD-883 test methods are proposed, both to correct errors and ambiguities and to facilitate the gathering of repeatable data on automated test equipment. Data obtained showed no sensitivity to measurement or temperature sequence nor to temperature ambient, provided that test times were not excessive. V sub ICP tests and some low current measurements required allowance for a pin condition settling time because of the test system speed. Some pin condition application sequences yielded incorrect measurements. Undefined terminal conditions of output pins were found to affect I sub OS and propagation delay time measurements. Truth table test results varied with test frequency and V sub IL for low-power Schottky devices.

Cerebral Palsy. Fact Sheet = La Paralisis Cerebral. Hojas Informativas Sobre Discapacidades.

ERIC Educational Resources Information Center

National Information Center for Children and Youth with Disabilities, Washington, DC.

This fact sheet on cerebral palsy is written in both English and Spanish. First, it provides a definition of cerebral palsy and considers various causes (e.g., an insufficient amount of oxygen reaching the fetal or newborn brain). The fact sheet then offers incidence figures and explains characteristics of the three main types of cerebral palsy:…

[Developing patient information sheets in general practice. Proposal for a methodology].

PubMed

Sustersic, Mélanie; Meneau, Aurélia; Drémont, Roger; Paris, Adeline; Laborde, Laurent; Bosson, Jean-Luc

2008-12-15

Health information is patients' wish and right. For general practitioners, it is a duty, a legal obligation and a pre-requisite in any preventive approach. Written information must complete oral information since it improves health care quality. However, in general practice, there are no patient documents which are scientifically valid, understandable and efficient in terms of communication. To develop a method for creating patient information sheets and to experiment its feasibility through the development of 125 sheets focused on the most common clinical conditions in general practice. Research and literature review pour the development of specifications, and creation of 125 sheets following these specifications. The specifications developed consist of the 10 following steps: selection of the topic and the objectives, literature review, selection of the sections, drafting, validation of the scientific contents, assessment among patients, validation of the layout, selection of the media, delivery to patients and update. Following these specifications, we developed 125 information sheets. Each of these was reviewed by several physicians and assessed with R. Flesh readability test (the established acceptable threshold value was 40). The 30 sheets associated with the lowest scores were selected and reviewed to improve their overall readability. Even though some difficulties cannot be avoided when developing patient information sheets, each physician or physician association can create its own documents following the proposed specifications and thus deliver a customized message.

Math for Masons. (Revised).

ERIC Educational Resources Information Center

Heppa, Victor

This student manual is concerned with the practical application of mathematics as used by masons. The manual's design allows students to work at their own pace. Included in each of the five units are individual lesson sheets with written instructions and explanations. Each information sheet states that topic's objectives, information about the…

Epilepsy. Fact Sheet = Epilepsia. Hojas Informativas Sobre Discapacidades.

ERIC Educational Resources Information Center

National Information Center for Children and Youth with Disabilities, Washington, DC.

This fact sheet, written in both English and Spanish, provides a definition, information on incidence, typical characteristics, and educational implications of epilepsy. It notes that epilepsy is classified as "other health impaired" under the Individuals with Disabilities Education Act (IDEA) and that children with epilepsy or seizure disorders…

Emotional Disturbance. Fact Sheet = Problemas Emocionales. Hojas Informativas Sobre Discapacidades.

ERIC Educational Resources Information Center

National Information Center for Children and Youth with Disabilities, Washington, DC.

This fact sheet, written in both English and Spanish, provides a definition, information on incidence, typical characteristics, and educational implications of emotional disturbance. The definition is from the Individuals with Disabilities Education Act (IDEA) and incidence in 1999-2000 is reported as about 470,000 children and youth. Educational…

Finite element simulation and Experimental verification of Incremental Sheet metal Forming

NASA Astrophysics Data System (ADS)

Kaushik Yanamundra, Krishna; Karthikeyan, R., Dr.; Naranje, Vishal, Dr

2018-04-01

Incremental sheet metal forming is now a proven manufacturing technique that can be employed to obtain application specific, customized, symmetric or asymmetric shapes that are required by automobile or biomedical industries for specific purposes like car body parts, dental implants or knee implants. Finite element simulation of metal forming process is being performed successfully using explicit dynamics analysis of commercial FE software. The simulation is mainly useful in optimization of the process as well design of the final product. This paper focuses on simulating the incremental sheet metal forming process in ABAQUS, and validating the results using experimental methods. The shapes generated for testing are of trapezoid, dome and elliptical shapes whose G codes are written and fed into the CNC milling machine with an attached forming tool with a hemispherical bottom. The same pre-generated coordinates are used to simulate a similar machining conditions in ABAQUS and the tool forces, stresses and strains in the workpiece while machining are obtained as the output data. The forces experimentally were recorded using a dynamometer. The experimental and simulated results were then compared and thus conclusions were drawn.

Energy information sheets

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1993-12-02

The National Energy Information Center (NEIC), as part of its mission, provides energy information and referral assistance to Federal, State, and local governments, the academic community, business and industrial organizations, and the general public. Written for the general public, the EIA publication Energy Information Sheets was developed to provide information on various aspects of fuel production, prices, consumption and capability. The information contained herein pertains to energy data as of December 1991. Additional information on related subject matter can be found in other EIA publications as referenced at the end of each sheet.

Mental Retardation. Fact Sheet = El Retraso Mental. Hojas Informativas Sobre Discapacidades.

ERIC Educational Resources Information Center

National Information Center for Children and Youth with Disabilities, Washington, DC.

This fact sheet on mental retardation is written in both English and Spanish. It begins with a vignette of a 15-year-old boy with mental retardation. Mental retardation is briefly explained as are some causes of mental retardation. It notes that a diagnosis of mental retardation looks at two things: first, the ability of a person's brain to learn,…

Two for one: a self-management plan coupled with a prescription sheet for children with asthma.

PubMed

Ducharme, Francine M; Noya, Francisco; McGillivray, David; Resendes, Sandy; Ducharme-Bénard, Stéphanie; Zemek, Roger; Bhogal, Sanjit Kaur; Rouleau, Rachel

2008-10-01

Despite strong recommendations in the asthma guidelines, the use of written self-management plans remains low among asthmatic patients. To develop a written self-management plan, based on scientific evidence and expert opinions, in a format intended to facilitate its dispensing by health care professionals, and to test the perception of its relevance and clarity by asthmatic children, adolescents and adults. Inspired by previously tested self-management plans, surveys of asthma educators, expert opinions and the 2004 Canadian Asthma Guidelines, the authors simultaneously developed French and English versions of a written self-management plan that coupled with a prescription. The self-management plan was tested in parents and their asthmatic children (aged one to 17 years), and it was revised until 85% clarity and perceived relevance was achieved. Ninety-seven children and their parents were interviewed. Twenty per cent had a self-management plan. On the final revision, nearly all items were clear and perceived relevant by 85% or more of the interviewees. Two self-management plans were designed for clinics and acute care settings, respectively. The plans are divided into three control zones identified by symptoms with optional peak flow values and symbolized by traffic light colours. They are designed in triplicate format with a prescription slip, a medical chart copy and a patient copy. The written self-management plans, based on available scientific evidence and expert opinions, are clear and perceived to be relevant by children, adolescents and their parents. By incorporating the prescription and chart copies, they were designed to facilitate dispensing by physicians in both clinics and acute care settings.

e-Manifest for Hazardous Wastes in Texas

EPA Pesticide Factsheets

EPA launches the hazardous waste electronic manifest (e-Manifest) system on June 30, 2018. The fact sheets here are written from EPA's federal perspective but do contain useful information about Texas

e-Manifest for Hazardous Wastes in Arkansas

EPA Pesticide Factsheets

EPA launches the hazardous waste electronic manifest (e-Manifest) system on June 30, 2018. The fact sheets here are written from EPA's federal perspective but do contain useful information about Arkansas

e-Manifest for Hazardous Wastes in Louisiana

EPA Pesticide Factsheets

EPA launches the hazardous waste electronic manifest (e-Manifest) system on June 30, 2018. The fact sheets here are written from EPA's federal perspective but do contain useful information about Louisiana

e-Manifest for Hazardous Wastes in Oklahoma

EPA Pesticide Factsheets

EPA launches the hazardous waste electronic manifest (e-Manifest) system on June 30, 2018. The fact sheets here are written from EPA's federal perspective but do contain useful information about Oklahoma

Mechanisms test bed math model modification and simulation support

NASA Technical Reports Server (NTRS)

Gilchrist, Andrea C.; Tobbe, Patrick A.

1995-01-01

This report summarizes the work performed under contract NAS8-38771 in support of the Marshall Space Flight Center Six Degree of Freedom Motion Facility and Flight Robotics Laboratory. The contract activities included the development of the two flexible body and Remote Manipulator System simulations, Dynamic Overhead Target Simulator control system and operating software, Global Positioning System simulation, and Manipulator Coupled Spacecraft Controls Testbed. Technical support was also provided for the Lightning Imaging Sensor and Solar X-Ray Imaging programs. The cover sheets and introductory sections for the documentation written under this contract are provided as an appendix.

General RMP Guidance - Appendix D: OSHA Guidance on PSM

EPA Pesticide Factsheets

OSHA's Process Safety Management (PSM) Guidance on providing complete and accurate written information concerning process chemicals, process technology, and process equipment; including process hazard analysis and material safety data sheets.

Data Processing: Status of Agriculture's Electronic Dissemination of Information System. Fact Sheet for the Chairman, Subcommittee on Government Information, Justice, and Agriculture, Committee on Government Operations, House of Representatives.

ERIC Educational Resources Information Center

General Accounting Office, Washington, DC.

Written in response to a request to review the implementation of the Department of Agriculture's Electronic Dissemination of Information (EDI) system, this fact sheet discusses the performance of the contractor operating the system and the role of EDI in the Department of Agriculture's overall public dissemination activities. A letter from the…

e-Manifest for Hazardous Wastes in New Mexico

EPA Pesticide Factsheets

EPA launches the hazardous waste electronic manifest (e-Manifest) system on June 30, 2018. The fact sheets here are written from EPA's federal perspective but do contain useful information about New Mexico

Physiotherapy exercise programmes: are instructional exercise sheets effective?

PubMed

Smith, Jo; Lewis, Jeremy; Prichard, Diana

2005-01-01

Effective compliance with physiotherapy exercises is only possible if patients remember the exercises accurately. The purpose of this study was to assess how well elderly in-patients remembered simple physiotherapy exercises, by comparing the ability to accurately reproduce a set of exercises in a group of patients that had received a written exercise sheet, with a group that had not. The study also aimed to investigate the relationship between memory for exercises and cognition. Sixty-four in-patients in an acute hospital were taught 3 exercises. Half of the subjects were randomised to receive exercise sheets to reinforce the teaching (Group 1). The rest of the subjects did not receive this memory aid (Group 2). Two to three days later subjects were asked to demonstrate their exercises. The accurate recall of the exercises was scored using a new assessment scale with a maximum score of 24. The mean exercise score was 17.19 for group 1 (SD = 5.91) and 16.24 for Group 2 (SD = 6.01). There was no significant difference in exercise score between groups (Mann Whitney U test p = 0.44). There was a statistically significant small positive correlation between exercise score and cognition (tau = 0.263). The study showed that older adult in-patients do not remember physiotherapy exercises effectively after a single teaching session and that their memory is not significantly improved by provision of an exercise sheet.

Leniency and halo effects in marking undergraduate short research projects.

PubMed

McKinstry, Brian H; Cameron, Helen S; Elton, Robert A; Riley, Simon C

2004-11-29

Supervisors are often involved in the assessment of projects they have supervised themselves. Previous research suggests that detailed marking sheets may alleviate leniency and halo effects. We set out to determine if, despite using such a marking schedule, leniency and halo effects were evident in the supervisors' marking of undergraduate short research projects (special study modules (SSM)). Review of grades awarded by supervisors, second markers and control markers to the written reports of 4th year medical students who had participated in an SSM during two full academic years (n = 399). Paired t-tests were used to compare mean marks, Pearson correlation to look at agreement between marks and multiple linear regression to test the prediction of one mark from several others adjusted for one another. There was a highly significant difference of approximately half a grade between supervisors and second markers with supervisors marking higher. (t = 3.12, p < 0.01, difference in grade score = 0.42, 95% CI for mean difference 0.18-0.80). There was a high correlation between the two marks awarded for performance of the project and the written report by the supervisor (r = 0.75), but a low-modest correlation between supervisor and second marker (r = 0.28). Linear regression analysis of the influence of the supervisors' mark for performance on their mark for the report gave a non-significant result. This suggests a leniency effect but no halo effect. This study shows that with the use of structured marking sheet for assessment of undergraduate medical students, supervisors marks are not associated with a halo effect, but leniency does occur. As supervisor assessment is becoming more common in both under graduate and postgraduate teaching new ways to improve objectivity in marking and to address the leniency of supervisors should be sought.

How to Involve Concessionaires & Vendors in Your Recycling Program

EPA Pesticide Factsheets

This fact sheet is written for operations managers, recycling and event coordinators, and other key decisionmakers involved in planning and managing public venues and events. It explains the key role in recycling played by concessionaires.

Compensatory Mitigation Site Protection Instrument Handbook and Fact Sheet

EPA Pesticide Factsheets

The site protection instrument is a written description of the legal arrangements including site ownership, management, and enforcement of any use restrictions that will be used to ensure the long-term protection of the compensatory mitigation project site

An object-oriented, coprocessor-accelerated model for ice sheet simulations

NASA Astrophysics Data System (ADS)

Seddik, H.; Greve, R.

2013-12-01

Recently, numerous models capable of modeling the thermo-dynamics of ice sheets have been developed within the ice sheet modeling community. Their capabilities have been characterized by a wide range of features with different numerical methods (finite difference or finite element), different implementations of the ice flow mechanics (shallow-ice, higher-order, full Stokes) and different treatments for the basal and coastal areas (basal hydrology, basal sliding, ice shelves). Shallow-ice models (SICOPOLIS, IcIES, PISM, etc) have been widely used for modeling whole ice sheets (Greenland and Antarctica) due to the relatively low computational cost of the shallow-ice approximation but higher order (ISSM, AIF) and full Stokes (Elmer/Ice) models have been recently used to model the Greenland ice sheet. The advance in processor speed and the decrease in cost for accessing large amount of memory and storage have undoubtedly been the driving force in the commoditization of models with higher capabilities, and the popularity of Elmer/Ice (http://elmerice.elmerfem.com) with an active user base is a notable representation of this trend. Elmer/Ice is a full Stokes model built on top of the multi-physics package Elmer (http://www.csc.fi/english/pages/elmer) which provides the full machinery for the complex finite element procedure and is fully parallel (mesh partitioning with OpenMPI communication). Elmer is mainly written in Fortran 90 and targets essentially traditional processors as the code base was not initially written to run on modern coprocessors (yet adding support for the recently introduced x86 based coprocessors is possible). Furthermore, a truly modular and object-oriented implementation is required for quick adaptation to fast evolving capabilities in hardware (Fortran 2003 provides an object-oriented programming model while not being clean and requiring a tricky refactoring of Elmer code). In this work, the object-oriented, coprocessor-accelerated finite element code Sainou is introduced. Sainou is an Elmer fork which is reimplemented in Objective C and used for experimenting with ice sheet models running on coprocessors, essentially GPU devices. GPUs are highly parallel processors that provide opportunities for fine-grained parallelization of the full Stokes problem using the standard OpenCL language (http://www.khronos.org/opencl/) to access the device. Sainou is built upon a collection of Objective C base classes that service a modular kernel (itself a base class) which provides the core methods to solve the finite element problem. An early implementation of Sainou will be presented with emphasis on the object architecture and the strategies of parallelizations. The computation of a simple heat conduction problem is used to test the implementation which also provides experimental support for running the global matrix assembly on GPU.

A Spreadsheet for the Mixing of a Row of Jets with a Confined Crossflow

NASA Technical Reports Server (NTRS)

Holderman, J. D.; Smith, T. D.; Clisset, J. R.; Lear, W. E.

2005-01-01

An interactive computer code, written with a readily available software program, Microsoft Excel (Microsoft Corporation, Redmond, WA) is presented which displays 3 D oblique plots of a conserved scalar distribution downstream of jets mixing with a confined crossflow, for a single row, double rows, or opposed rows of jets with or without flow area convergence and/or a non-uniform crossflow scalar distribution. This project used a previously developed empirical model of jets mixing in a confined crossflow to create an Microsoft Excel spreadsheet that can output the profiles of a conserved scalar for jets injected into a confined crossflow given several input variables. The program uses multiple spreadsheets in a single Microsoft Excel notebook to carry out the modeling. The first sheet contains the main program, controls for the type of problem to be solved, and convergence criteria. The first sheet also provides for input of the specific geometry and flow conditions. The second sheet presents the results calculated with this routine to show the effects on the mixing of varying flow and geometric parameters. Comparisons are also made between results from the version of the empirical correlations implemented in the spreadsheet and the versions originally written in Applesoft BASIC (Apple Computer, Cupertino, CA) in the 1980's.

A Spreadsheet for the Mixing of a Row of Jets with a Confined Crossflow. Supplement

NASA Technical Reports Server (NTRS)

Holderman, J. D.; Smith, T. D.; Clisset, J. R.; Lear, W. E.

2005-01-01

An interactive computer code, written with a readily available software program, Microsoft Excel (Microsoft Corporation, Redmond, WA) is presented which displays 3 D oblique plots of a conserved scalar distribution downstream of jets mixing with a confined crossflow, for a single row, double rows, or opposed rows of jets with or without flow area convergence and/or a non-uniform crossflow scalar distribution. This project used a previously developed empirical model of jets mixing in a confined crossflow to create an Microsoft Excel spreadsheet that can output the profiles of a conserved scalar for jets injected into a confined crossflow given several input variables. The program uses multiple spreadsheets in a single Microsoft Excel notebook to carry out the modeling. The first sheet contains the main program, controls for the type of problem to be solved, and convergence criteria. The first sheet also provides for input of the specific geometry and flow conditions. The second sheet presents the results calculated with this routine to show the effects on the mixing of varying flow and geometric parameters. Comparisons are also made between results from the version of the empirical correlations implemented in the spreadsheet and the versions originally written in Applesoft BASIC (Apple Computer, Cupertino, CA) in the 1980's.

Quantitative analysis of defects in silicon. Silicon sheet growth development for the large are silicon sheet task of the low-cost solar array project

NASA Technical Reports Server (NTRS)

Natesh, R.; Smith, J. M.; Bruce, T.; Oidwai, H. A.

1980-01-01

One hundred and seventy four silicon sheet samples were analyzed for twin boundary density, dislocation pit density, and grain boundary length. Procedures were developed for the quantitative analysis of the twin boundary and dislocation pit densities using a QTM-720 Quantitative Image Analyzing system. The QTM-720 system was upgraded with the addition of a PDP 11/03 mini-computer with dual floppy disc drive, a digital equipment writer high speed printer, and a field-image feature interface module. Three versions of a computer program that controls the data acquisition and analysis on the QTM-720 were written. Procedures for the chemical polishing and etching were also developed.

Colonial Broadsides: A Student-Created Play. [Lesson Plan].

ERIC Educational Resources Information Center

2002

"Broadsides" are notices written on disposable, single sheets of paper printed on one side only, intended to have an immediate impact on readers. Broadsides had an impact in colonial America--they delivered the latest news and much more: government proclamations, public service announcements, opinion papers, advertisements, and…

Exact analytical formulae for linearly distributed vortex and source sheets in uence computation in 2D vortex methods

NASA Astrophysics Data System (ADS)

Kuzmina, K. S.; Marchevsky, I. K.; Ryatina, E. P.

2017-11-01

We consider the methodology of numerical schemes development for two-dimensional vortex method. We describe two different approaches to deriving integral equation for unknown vortex sheet intensity. We simulate the velocity of the surface line of an airfoil as the influence of attached vortex and source sheets. We consider a polygonal approximation of the airfoil and assume intensity distributions of free and attached vortex sheets and attached source sheet to be approximated with piecewise constant or piecewise linear (continuous or discontinuous) functions. We describe several specific numerical schemes that provide different accuracy and have a different computational cost. The study shows that a Galerkin-type approach to solving boundary integral equation requires computing several integrals and double integrals over the panels. We obtain exact analytical formulae for all the necessary integrals, which makes it possible to raise significantly the accuracy of vortex sheet intensity computation and improve the quality of velocity and vorticity field representation, especially in proximity to the surface line of the airfoil. All the formulae are written down in the invariant form and depend only on the geometric relationship between the positions of the beginnings and ends of the panels.

Prediction and verification of creep behavior in metallic materials and components for the space shuttle thermal protection system

NASA Technical Reports Server (NTRS)

Davis, J. W.; Cramer, B. A.

1976-01-01

A method of analysis was developed for predicting permanent cyclic creep deflections in stiffened panel structures. This method uses creep equations based on cyclic tensile creep tests and a computer program to predict panel deflections as a function of mission cycle. Four materials were investigated - a titanium alloy (Ti-6Al-4V), a cobalt alloy (L605), and two nickel alloys (Rene'41 and TDNiCr). Steady-state and cyclic creep response data were obtained by testing tensile specimens fabricated from thin gage sheet (0.025 and 0.63 cm nominal). Steady-state and cyclic creep equations were developed which describe creep as a function of time, temperature and load. Tests were also performed on subsize (6.35 x 30.5 cm) rib and corrugation stiffened panels. These tests were used to correlate creep responses between elemental specimens and panels. The panel response was analyzed by use of a specially written computer program.

Leniency and halo effects in marking undergraduate short research projects

PubMed Central

McKinstry, Brian H; Cameron, Helen S; Elton, Robert A; Riley, Simon C

2004-01-01

Background Supervisors are often involved in the assessment of projects they have supervised themselves. Previous research suggests that detailed marking sheets may alleviate leniency and halo effects. We set out to determine if, despite using such a marking schedule, leniency and halo effects were evident in the supervisors' marking of undergraduate short research projects (special study modules (SSM)). Methods Review of grades awarded by supervisors, second markers and control markers to the written reports of 4th year medical students who had participated in an SSM during two full academic years (n = 399). Paired t-tests were used to compare mean marks, Pearson correlation to look at agreement between marks and multiple linear regression to test the prediction of one mark from several others adjusted for one another. Results There was a highly significant difference of approximately half a grade between supervisors and second markers with supervisors marking higher. (t = 3.12, p < 0.01, difference in grade score = 0.42, 95% CI for mean difference 0.18–0.80). There was a high correlation between the two marks awarded for performance of the project and the written report by the supervisor (r = 0.75), but a low-modest correlation between supervisor and second marker (r = 0.28). Linear regression analysis of the influence of the supervisors' mark for performance on their mark for the report gave a non-significant result. This suggests a leniency effect but no halo effect. Conclusions This study shows that with the use of structured marking sheet for assessment of undergraduate medical students, supervisors marks are not associated with a halo effect, but leniency does occur. As supervisor assessment is becoming more common in both under graduate and postgraduate teaching new ways to improve objectivity in marking and to address the leniency of supervisors should be sought. PMID:15569395

40 CFR 63.471 - Facility-wide standards.

Code of Federal Regulations, 2014 CFR

2014-07-01

... solvent, recycled solvent, and used solvent that has been cleaned of soiled materials. A fill line must be... section either in electronic or written form for a period of 5 years. For purposes of this paragraph... using the procedure described in paragraph (c)(3) of this section. (3) Calculation sheets showing how...

40 CFR 63.471 - Facility-wide standards.

Code of Federal Regulations, 2013 CFR

2013-07-01

... solvent, recycled solvent, and used solvent that has been cleaned of soiled materials. A fill line must be... section either in electronic or written form for a period of 5 years. For purposes of this paragraph... using the procedure described in paragraph (c)(3) of this section. (3) Calculation sheets showing how...

Energy from the Atom.

ERIC Educational Resources Information Center

Smith, Patricia L.

This curriculum guide was written to supplement fifth and sixth grade science units on matter and energy. It was designed to provide more in-depth material on the atom. The first part, "Teacher Guide," contains background information, biographical sketches of persons in the history of nuclear energy, vocabulary, answer sheets, management sheets…

Shorter intervals between great earthquakes near Sendai: Scour ponds and a sand layer attributable to A.D. 1454 overwash

NASA Astrophysics Data System (ADS)

Sawai, Yuki; Namegaya, Yuichi; Tamura, Toru; Nakashima, Rei; Tanigawa, Koichiro

2015-06-01

A sparsely documented tsunami in 1454 may subdivide the recurrence interval between the 869 and 2011 tsunamis near Sendai, as judged from geomorphic, stratigraphic, and archival evidence. Pond-filled breaches cut across beach ridges on century-old topographic maps. The basal pond deposit in one of these breaches postdates 1454. Stratigraphy on Sendai Plain includes a sand sheet that contains marine and brackish diatoms. Radiocarbon ages suggest that the sheet dates to 1406-1615 (2σ), and written records for this interval in Tohoku mention a tsunami in 1454. The inferred inundation extended 1.0-2.5 km inland from an approximate medieval shoreline. Simulated tsunamis that best account for the sand sheet require a thrust earthquake of moment magnitude 8.4 or larger. If the sand sheet represents the 1454 tsunami, the two most recent intervals between great thrust earthquakes in Sendai region spanned 585 and 557 years.

Trends and Techniques for Space Base Electronics

NASA Technical Reports Server (NTRS)

Trotter, J. D.; Wade, T. E.; Gassaway, J. D.

1979-01-01

Simulations of various phosphorus and boron diffusions in SOS were completed and a sputtering system, furnaces, and photolithography related equipment were set up. Double layer metal experiments initially utilized wet chemistry techniques. By incorporating ultrasonic etching of the vias, premetal cleaning a modified buffered HF, phosphorus doped vapox, and extended sintering, yields of 98% were obtained using the standard test pattern. A two dimensional modeling program was written for simulating short channel MOSFETs with nonuniform substrate doping. A key simplifying assumption used is that the majority carriers can be represented by a sheet charge at the silicon dioxide silicon interface. Although the program is incomplete, the two dimensional Poisson equation for the potential distribution was achieved. The status of other Z-D MOSFET simulation programs is summarized.

Usefulness of head injury instruction forms in home observation of mild head injuries.

PubMed

Warren, D; Kissoon, N

1989-06-01

We prospectively studied a group of patients with mild head injury discharged for home observation to determine whether written instructions assisted in recall of signs and symptoms, increased patient satisfaction, or resulted in any additional benefit over verbal explanations alone. We also evaluated the level of comprehension required to understand the written instructions in their present form. Over a three-month period, 72 patients (43 male, 29 female) with a mean age of 4.4 (SD +/- 3.9) years were studied. In addition to verbal explanations for all parents, 38 parents received written instructions. Each group remembered 4/7 (57%) of signs and symptoms and was equally satisfied with verbal explanations. The majority (84%) of parents who received instruction sheets intended to keep these for further reference. Low recall of two instructions may be due to poor comprehension of the language used. We conclude that written instructions (1) did not add significantly to recall, (2) may provide reassurance to parents, and (3) need to be written in simple lay terms in order to be understood by the parents/patients served.

Micro-Scale Mechanical Testing of Non-Woven Carbon Nanotube Sheets and Yarns

NASA Technical Reports Server (NTRS)

Magargee, J.; Morestin, F.; Cao, J.; Jones, J. S.

2013-01-01

Non-woven carbon nanotube (CNT) sheets and yarns were tested using a novel micro-scale mechanical testing system. CNT sheets were observed to delaminate during uniaxial testing using an adbesive gripping method, resulting from a higher proportion of load bearing in the outer sheets versus internal sheets and an apparently low interlaminar shear strength. In response to this, a new spool-grip method was used to alleviate non-uniform through-thickness stresses, circumvent premature delamination, and allow the sheet material to sustain a 72% increase in measured tensile strength. Furthermore, tension tests of CNT yarns showed that the yarn-structure was approximaiely 7 times stronger than the sheet structure, owing to a higher degree of CNT alignment in the test direction.

Getting Started in Classroom Computing.

ERIC Educational Resources Information Center

Ahl, David H.

Written for secondary students, this booklet provides an introduction to several computer-related concepts through a set of six classroom games, most of which can be played with little more than a sheet of paper and a pencil. The games are: 1) SECRET CODES--introduction to binary coding, punched cards, and paper tape; 2) GUESS--efficient methods…

Key findings on legal and regulatory barriers to HIV testing and access to care across Europe.

PubMed

Power, L; Hows, J; Jakobsen, S F

2018-02-01

The aim of this work within OptTEST by HiE has been to demonstrate the role of legal and regulatory barriers in hindering access to HIV testing, treatment and care across Europe and to produce tools to help dismantle them. An online survey to assess country-specific data on legal and regulatory barriers distributed widely across the WHO Europe region. Literature reviews conducted in January-October 2015 in English, in November 2015 in Russian, and updated in April 2017. Semi-structured interviews were conducted with 25 key actors within the HIV field to feed into case studies and tip sheets on how to dismantle legal and regulatory barriers. More than 160 individuals and organisations from 49 countries across the WHO European region provided responses which were analysed and cross checked with other data sources and a searchable database produced (legalbarriers.peoplewithhiveurope.org). The conducted literature reviews yielded 88 papers and reports which identify legal and regulatory barriers to key populations' access to HV testing and care. Based on the interviews with key actors, ranging from PLHIV activists to government officials, on lessons-learned, a series of tip sheets and ten case studies were written-up intended to inform and inspire the HIV community to address and overcome existing barriers (opttest.eu/Tools). While some of the barriers identified may require major changes to wider health systems, or long term legal reform, many are open to a simple change in regulations or custom and practice. We have the tools. Why can't we finish the job? © 2018 British HIV Association.

Mammography with and without radiolucent positioning sheets: Comparison of projected breast area, pain experience, radiation dose and technical image quality.

PubMed

Timmers, Janine; Voorde, Marloes Ten; Engen, Ruben E van; Landsveld-Verhoeven, Cary van; Pijnappel, Ruud; Greve, Kitty Droogh-de; Heeten, Gerard J den; Broeders, Mireille J M

2015-10-01

To compare projected breast area, image quality, pain experience and radiation dose between mammography performed with and without radiolucent positioning sheets. 184 women screened in the Dutch breast screening programme (May-June 2012) provided written informed consent to have one additional image taken with positioning sheets. 5 cases were excluded (missing data). Pain was scored using the Numeric Rating Scale. Radiation dose was estimated using the Dance model and projected breast area using computer software. Two radiologists and two radiographers assessed image quality. With positioning sheets significantly more pectoral muscle, lateral and medial breast tissue was projected (CC-views) and more and deeper depicted pectoral muscle (MLO-views). In contrast, visibility of white and darker areas was better on images without positioning sheets, radiologists were therefore better able to detect abnormalities (MLO-views). Women experienced more pain with positioning sheets (MLO-views only, mean difference NRS 0.98; SD 1.71; p=0,00). Mammograms with positioning sheets showed more breast tissue. Increased breast thickness after compression with sheets resulted in less visibility of white and darker areas and thus reduced detection of abnormalities. Also, women experienced more pain (MLO-views) due to the sheet material. A practical consideration is the fact that more subcutaneous fat tissue and skin are being pulled forward leading to folds in the nipple area. On balance, improvement to the current design is required before implementation in screening practice can be considered. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

Technical analysis of the Slosson Written Expression Test.

PubMed

Erford, Bradley T; Hofler, Donald B

2004-06-01

The Slosson Written Expression Test was designed to assess students ages 8-17 years at risk for difficulties in written expression. Scores from three independent samples were used to evaluate the test's reliability and validity for measuring students' written expression. Test-retest reliability of the SWET subscales ranged from .80 to .94 (n = 151), and .95 for the Written Expression Total Standard Scores. The median alternate-form reliability for students' Written Expression Total Standard Scores was .81 across the three forms. Scores on the Slosson test yielded concurrent validity coefficients (n = 143) of .60 with scores from the Woodcock-Johnson: Tests of Achievement-Third Edition Broad Written Language Domain and .49 with scores on the Test of Written Language-Third Edition Spontaneous Writing Quotient. Exploratory factor analytic procedures suggested the Slosson test is comprised of two dimensions, Writing Mechanics and Writing Maturity (47.1% and 20.1% variance accounted for, respectively). In general, the Slosson Written Expression Test presents with sufficient technical characteristics to be considered a useful written expression screening test.

Research on Al-alloy sheet forming formability during warm/hot sheet hydroforming based on elliptical warm bulging test

NASA Astrophysics Data System (ADS)

Cai, Gaoshen; Wu, Chuanyu; Gao, Zepu; Lang, Lihui; Alexandrov, Sergei

2018-05-01

An elliptical warm/hot sheet bulging test under different temperatures and pressure rates was carried out to predict Al-alloy sheet forming limit during warm/hot sheet hydroforming. Using relevant formulas of ultimate strain to calculate and dispose experimental data, forming limit curves (FLCS) in tension-tension state of strain (TTSS) area are obtained. Combining with the basic experimental data obtained by uniaxial tensile test under the equivalent condition with bulging test, complete forming limit diagrams (FLDS) of Al-alloy are established. Using a quadratic polynomial curve fitting method, material constants of fitting function are calculated and a prediction model equation for sheet metal forming limit is established, by which the corresponding forming limit curves in TTSS area can be obtained. The bulging test and fitting results indicated that the sheet metal FLCS obtained were very accurate. Also, the model equation can be used to instruct warm/hot sheet bulging test.

Valuing Exercises for the Middle School. Resource Monograph No. 11.

ERIC Educational Resources Information Center

Casteel, J. Doyle; And Others

One of the major goals of the middle school is to help students gain and refine skills in the area of values clarification. One way of securing such value clarification is to plan and assign value sheets--carefully planned and written activities designed to elicit value clarification patterns of language usage from students. Six different formats…

Of Dirty Sheets and Worse: Administration Costs and Staffing Matters.

ERIC Educational Resources Information Center

Keigher, Sharon M.

1993-01-01

Considers article written by professor of social welfare in 1981 in which job security of social workers is addressed. Compares views expressed in 1981 with situation faced by social workers today. Considers danger of administration costs resulting in short-staffing of hospitals serving the poor and discusses case of 22-year-old obstetrics patient…

The Complete Get That Job! A Quick and Easy Guide with Worksheets.

ERIC Educational Resources Information Center

2001

Written for adult new readers, this workbook contains 14 chapters of information on career development, job search and job retention skills. Chapters contain information, worksheets, examples, and summary sheets. The guide is intended to help adults use basic skills to decide what they can do well, identify their job search goals, pick the best…

Experimental formability analysis of bondal sandwich sheet

NASA Astrophysics Data System (ADS)

Kami, Abdolvahed; Banabic, Dorel

2018-05-01

Metal/polymer/metal sandwich sheets have recently attracted the interests of industries like automotive industry. These sandwich sheets have superior properties over single-layer metallic sheets including good sound and vibration damping and light weight. However, the formability of these sandwich sheets should be enhanced which requires more research. In this paper, the formability of Bondal sheet (DC06/viscoelastic polymer/DC06 sandwich sheet) was studied through different types of experiments. The mechanical properties of Bondal were determined by uniaxial tensile tests. Hemispherical punch stretching and hydraulic bulge tests were carried out to determine the forming limit diagram (FLD) of Bondal. Furthermore, cylindrical and square cup drawing tests were performed in dry and oil lubricated conditions. These tests were conducted at different blank holding forces (BHFs). An interesting observation about Bondal sheet deep drawing was obtaining of higher drawing depths at dry condition in comparison with oil-lubricated condition.

76 FR 61763 - Extension: Form N-17f-2; Proposed Collection; Comment Request

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-05

...: Form N-17f-2; Proposed Collection; Comment Request Upon Written Request, Copies Available From... information to the Office of Management and Budget for extension and approval. Form N-17f-2 (17 CFR 274.220... Investments in the Custody of Management Investment Companies.'' Form N-17f-2 is the cover sheet for the...

76 FR 36011 - Airworthiness Directives; Fokker Services B.V. Model F.27 Mark 050, 200, 300, 400, 500, 600, and...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-21

...: Comments Invited We invite you to send any written relevant data, views, or arguments about this proposed...-operate in developing and implementing common safety regulatory standards and procedures.) Under this...-28-042, including Drawing June 23, 2010. W41192, Sheet 012, Issue AG, dated June 23, 2010, Drawing...

Apples on Train Tracks: Observing Young Children Reenvision Their Writing

ERIC Educational Resources Information Center

Kissel, Brian

2008-01-01

Kissel focuses on 4-year-olds reenvisioning their writing in discussing his observations of pre-K children's writing during a two-year study. In a writers' workshop each day, children started with a clean sheet of paper. The teacher read aloud, then offered a minilesson, crafting a written piece--always with a picture--in front of the class. As…

Developing standards for chromosomal microarray testing counselling in paediatrics.

PubMed

Godfrey, Emma; Clark, Phillipa

2014-06-01

Chromosomal microarray testing (CMA) generally aids paediatric genetic diagnosis. However, pre-CMA counselling is important as results can be ambiguous, generate uncertainty and raise ethical issues. We developed standards for counselling and giving families results; using these we evaluated practice for children seen by the Auckland Developmental Paediatric team in 2011. Pretest discussion was documented in 14 of 28 subjects and potential outcomes in 4of 28. 8 of 28 received information leaflets, 1 of 28 gave signed consent. 3 of 3 with abnormal results and 4 of 5 with variants of unknown significance (VOUS) were offered clinical genetics referral. 8 of 20 families with normal results were written to; two with abnormal results were informed face-to-face and one in writing; most VOUS were communicated by phone, voicemail or letter. CMA testing requires clear patient information sheets and in-depth pretest discussion for informed consent, timely feedback of results and genetics referral as appropriate. Authoritative guidelines and training are needed to strengthen CMA counselling. ©2014 Foundation Acta Paediatrica. Published by John Wiley & Sons Ltd.

Computing Mass Properties From AutoCAD

NASA Technical Reports Server (NTRS)

Jones, A.

1990-01-01

Mass properties of structures computed from data in drawings. AutoCAD to Mass Properties (ACTOMP) computer program developed to facilitate quick calculations of mass properties of structures containing many simple elements in such complex configurations as trusses or sheet-metal containers. Mathematically modeled in AutoCAD or compatible computer-aided design (CAD) system in minutes by use of three-dimensional elements. Written in Microsoft Quick-Basic (Version 2.0).

Comprehensive optical and data management infrastructure for high-throughput light-sheet microscopy of whole mouse brains.

PubMed

Müllenbroich, M Caroline; Silvestri, Ludovico; Onofri, Leonardo; Costantini, Irene; Hoff, Marcel Van't; Sacconi, Leonardo; Iannello, Giulio; Pavone, Francesco S

2015-10-01

Comprehensive mapping and quantification of neuronal projections in the central nervous system requires high-throughput imaging of large volumes with microscopic resolution. To this end, we have developed a confocal light-sheet microscope that has been optimized for three-dimensional (3-D) imaging of structurally intact clarified whole-mount mouse brains. We describe the optical and electromechanical arrangement of the microscope and give details on the organization of the microscope management software. The software orchestrates all components of the microscope, coordinates critical timing and synchronization, and has been written in a versatile and modular structure using the LabVIEW language. It can easily be adapted and integrated to other microscope systems and has been made freely available to the light-sheet community. The tremendous amount of data routinely generated by light-sheet microscopy further requires novel strategies for data handling and storage. To complete the full imaging pipeline of our high-throughput microscope, we further elaborate on big data management from streaming of raw images up to stitching of 3-D datasets. The mesoscale neuroanatomy imaged at micron-scale resolution in those datasets allows characterization and quantification of neuronal projections in unsectioned mouse brains.

Using Separate Answer Sheets with Grade 3 Students

ERIC Educational Resources Information Center

Brooks, Thomas; O'Malley, Kimberly; Ragland, Shelley; Young, Michael; Kirkpatrick, Rob

2014-01-01

The authors compared the performance of third-grade students testing on answer sheets with those testing on machine-scored test booklets. The 1,832 students in the nationally representative sample were assigned at the campus level to complete the Stanford Achievement Test Series, Tenth Edition in 1 of 4 conditions: (a) Form A answer sheet, (b)…

Correlation of Simulation Examination to Written Test Scores for Advanced Cardiac Life Support Testing: Prospective Cohort Study.

PubMed

Strom, Suzanne L; Anderson, Craig L; Yang, Luanna; Canales, Cecilia; Amin, Alpesh; Lotfipour, Shahram; McCoy, C Eric; Osborn, Megan Boysen; Langdorf, Mark I

2015-11-01

Traditional Advanced Cardiac Life Support (ACLS) courses are evaluated using written multiple-choice tests. High-fidelity simulation is a widely used adjunct to didactic content, and has been used in many specialties as a training resource as well as an evaluative tool. There are no data to our knowledge that compare simulation examination scores with written test scores for ACLS courses. To compare and correlate a novel high-fidelity simulation-based evaluation with traditional written testing for senior medical students in an ACLS course. We performed a prospective cohort study to determine the correlation between simulation-based evaluation and traditional written testing in a medical school simulation center. Students were tested on a standard acute coronary syndrome/ventricular fibrillation cardiac arrest scenario. Our primary outcome measure was correlation of exam results for 19 volunteer fourth-year medical students after a 32-hour ACLS-based Resuscitation Boot Camp course. Our secondary outcome was comparison of simulation-based vs. written outcome scores. The composite average score on the written evaluation was substantially higher (93.6%) than the simulation performance score (81.3%, absolute difference 12.3%, 95% CI [10.6-14.0%], p<0.00005). We found a statistically significant moderate correlation between simulation scenario test performance and traditional written testing (Pearson r=0.48, p=0.04), validating the new evaluation method. Simulation-based ACLS evaluation methods correlate with traditional written testing and demonstrate resuscitation knowledge and skills. Simulation may be a more discriminating and challenging testing method, as students scored higher on written evaluation methods compared to simulation.

Iraqi Kurds. Their History and Culture. CAL Refugee Fact Sheet Series No. 13.

ERIC Educational Resources Information Center

Robson, Barbara

The Kurds are a distinct group of people who have inhabited the Middle East for as long as there have been written records. The Kurds are the second largest ethnic group in Iraq and Turkey and the third largest group in Iran. In 1975 and 1976, Kurdish refugees from Iraq were admitted to the United States after the failure of their attempt to…

Informed consent during the clinical emergency of acute myocardial infarction (HERO-2 consent substudy): a prospective observational study.

PubMed

Williams, Barbara F; French, John K; White, Harvey D

2003-03-15

Anxiety, fear, pain, and treatment with morphine might compromise the ability of patients to comprehend information about, and give informed consent for, participation in clinical trials. We aimed to assess whether patients with acute myocardial infarction could understand written and verbal information and whether they were competent to give autonomous informed consent to participate in a clinical trial. We prospectively studied 399 patients with acute myocardial infarction in 16 hospitals in New Zealand and Australia who were eligible for participation in the Hirulog and Early Reperfusion or Occlusion (HERO)-2 trial. We assessed readability of patient information sheets, patients' educational status, their views of the consent process, comprehension of verbal and written information, and competence to give consent. The patient information sheet needed a year 13 (age 18) educational level for comprehension, although only 75 of 345 patients (22%) had been educated beyond secondary school. Only 63 of 346 (18%) read the patient information sheet before giving or refusing consent to participate. Patients who gave consent were more likely to report good or partial comprehension of the information provided than were those who refused consent (272 [89%] vs 14 [70%], respectively; p=0.009). In an assessment of competence to make an autonomous decision, 75 of 145 (52%) were ranked at the lowest grade and 26 (18%) were not competent to consent. Although the consent process for HERO-2 met regulatory requirements for clinical trials, it was inappropriate for the needs of most patients. The patients' comprehension of the information provided and their competence to autonomously give consent was less than optimum.

An approach to computing discrete adjoints for MPI-parallelized models applied to Ice Sheet System Model 4.11

NASA Astrophysics Data System (ADS)

Larour, Eric; Utke, Jean; Bovin, Anton; Morlighem, Mathieu; Perez, Gilberto

2016-11-01

Within the framework of sea-level rise projections, there is a strong need for hindcast validation of the evolution of polar ice sheets in a way that tightly matches observational records (from radar, gravity, and altimetry observations mainly). However, the computational requirements for making hindcast reconstructions possible are severe and rely mainly on the evaluation of the adjoint state of transient ice-flow models. Here, we look at the computation of adjoints in the context of the NASA/JPL/UCI Ice Sheet System Model (ISSM), written in C++ and designed for parallel execution with MPI. We present the adaptations required in the way the software is designed and written, but also generic adaptations in the tools facilitating the adjoint computations. We concentrate on the use of operator overloading coupled with the AdjoinableMPI library to achieve the adjoint computation of the ISSM. We present a comprehensive approach to (1) carry out type changing through the ISSM, hence facilitating operator overloading, (2) bind to external solvers such as MUMPS and GSL-LU, and (3) handle MPI-based parallelism to scale the capability. We demonstrate the success of the approach by computing sensitivities of hindcast metrics such as the misfit to observed records of surface altimetry on the northeastern Greenland Ice Stream, or the misfit to observed records of surface velocities on Upernavik Glacier, central West Greenland. We also provide metrics for the scalability of the approach, and the expected performance. This approach has the potential to enable a new generation of hindcast-validated projections that make full use of the wealth of datasets currently being collected, or already collected, in Greenland and Antarctica.

An Approach to Computing Discrete Adjoints for MPI-Parallelized Models Applied to the Ice Sheet System Model}

NASA Astrophysics Data System (ADS)

Perez, G. L.; Larour, E. Y.; Morlighem, M.

2016-12-01

Within the framework of sea-level rise projections, there is a strong need for hindcast validation of the evolution of polar ice sheets in a way that tightly matches observational records (from radar and altimetry observations mainly). However, the computational requirements for making hindcast reconstructions possible are severe and rely mainly on the evaluation of the adjoint state of transient ice-flow models. Here, we look at the computation of adjoints in the context of the NASA/JPL/UCI Ice Sheet System Model, written in C++ and designed for parallel execution with MPI. We present the adaptations required in the way the software is designed and written but also generic adaptations in the tools facilitating the adjoint computations. We concentrate on the use of operator overloading coupled with the AdjoinableMPI library to achieve the adjoint computation of ISSM. We present a comprehensive approach to 1) carry out type changing through ISSM, hence facilitating operator overloading, 2) bind to external solvers such as MUMPS and GSL-LU and 3) handle MPI-based parallelism to scale the capability. We demonstrate the success of the approach by computing sensitivities of hindcast metrics such as the misfit to observed records of surface altimetry on the North-East Greenland Ice Stream, or the misfit to observed records of surface velocities on Upernavik Glacier, Central West Greenland. We also provide metrics for the scalability of the approach, and the expected performance. This approach has the potential of enabling a new generation of hindcast-validated projections that make full use of the wealth of datasets currently being collected, or alreay collected in Greenland and Antarctica, such as surface altimetry, surface velocities, and/or gravity measurements.

Damage Tolerance of Sandwich Plates with Debonded Face Sheets

NASA Technical Reports Server (NTRS)

Avery, John L., III; Sankar, Bhavani V.

1998-01-01

Axial compression tests were performed on debonded sandwich composites made of graphite/epoxy face-sheets and aramid fiber honeycomb core. The sandwich beams were manufactured using a vacuum baccrin2 process. The face-sheet and the sandwich beam were co-cured. Delamination between one of the face sheets and the core was introduced by using a Teflon layer during the curing process. Axial compression tests were performed to determine the ultimate load carrying capacity of the debonded beams. Flatwise tension tests and Double Cantilever Beam tests were performed to determine. respectively, the strength and fracture toughness of the face-sheet/core interface. From the test results semi-empirical formulas were derived for the fracture toughness and ultimate compressive load carrying capacity in terms of the core density. core thickness. face-sheet thickness and debond length. Four different failure modes and their relation to the structural properties were identified. Linear buckling analysis was found to be inadequate in predicting the compressive load carrying capacity of the debonded sandwich composites.

Hand-Drawn 'Weekly Information Sheets' Focus Teaching, Engage Students, and Improve Communication

NASA Astrophysics Data System (ADS)

Pound, K. S.

2016-12-01

Hand-drawn and lettered `Weekly Information Sheets' (WIS) were created on a weekly basis for an upper-level Sedimentology & Stratigraphy class. Use of these sheets resulted in improved work quality, attention to detail, communication skills, and overall engagement. The sheets were modeled on the work of Lynda Barry (https://www.drawnandquarterly.com/syllabus), and included a series of repeated elements: goofy/absurd newspaper clippings, marginally pertinent cartoon(s), a summary of the weeks activities / goals and lectures, as well as cartoon cat, mouse and penguin drawings with innane comments, quotes and general class reminders. The pedagogical aims for these weekly sheets were multifold. First, they were designed so that students could see the time and care I put in to the sheet - my hope was that this would show the time and care I expected them to put in to their work. Second, I wanted to create something students would take the time to read - despite this being a 400-level class, students are rarely diligent about reading a typewritten handout. Third, I wanted to have a vehicle for engaging them in the larger world, including ethical or moral dilemmas. Fourth, I wanted the students to reflectively consider the nature of communication in science. Finally, I wanted a mechanism to focus my thoughts on the teaching and learning for the upcoming week that went beyond simply reviewing my notes and activities. Student response to the WIS was positive; they read them, used them for organizing their class notes and exam review. Students arrived early for class on Mondays for the WIS - although I needed to give them time to read the sheet. Comparison with previous course offerings shows improvements in student communication skills (written reports, poster presentation) and overall achievement.

The Development of Student’s Activity Sheets (SAS) Based on Multiple Intelligences and Problem-Solving Skills Using Simple Science Tools

NASA Astrophysics Data System (ADS)

Wardani, D. S.; Kirana, T.; Ibrahim, M.

2018-01-01

The aim of this research is to produce SAS based on MI and problem-solving skills using simple science tools that are suitable to be used by elementary school students. The feasibility of SAS is evaluated based on its validity, practicality, and effectiveness. The completion Lesson Plan (LP) implementation and student’s activities are the indicators of SAS practicality. The effectiveness of SAS is measured by indicators of increased learning outcomes and problem-solving skills. The development of SAS follows the 4-D (define, design, develop, and disseminate) phase. However, this study was done until the third stage (develop). The written SAS was then validated through expert evaluation done by two experts of science, before its is tested to the target students. The try-out of SAS used one group with pre-test and post-test design. The result of this research shows that SAS is valid with “good” category. In addition, SAS is considered practical as seen from the increase of student activity at each meeting and LP implementation. Moreover, it was considered effective due to the significant difference between pre-test and post-test result of the learning outcomes and problem-solving skill test. Therefore, SAS is feasible to be used in learning.

Investigation of the Formability of TRIP780 Steel Sheets

NASA Astrophysics Data System (ADS)

Song, Yang

The formability of a metal sheet is dependent on its work hardening behaviour and its forming limits; and both aspects must be carefully determined in order to accurately simulate a particular forming process. This research aims to characterize the formability of a TRIP780 sheet steel using advanced experimental testing and analysis techniques. A series of flat rolling and tensile tests, as well as shear tests were conducted to determine the large deformation work hardening behaviour of this TRIP780 steel. Nakazima tests were carried out up to fracture to determine the forming limits of this sheet material. A highly-automated method for generating a robust FLC for sheet materials from DIC strain measurements was created with the help of finite element simulations, and evaluated against the conventional method. A correction algorithm that aims to compensate for the process dependent effects in the Nakazima test was implemented and tested with some success.

Science learning based on local potential: Overview of the nature of science (NoS) achieved

NASA Astrophysics Data System (ADS)

Wilujeng, Insih; Zuhdan Kun, P.; Suryadarma, IGP.

2017-08-01

The research concerned here examined the effectiveness of science learning conducted with local potential as basis from the point of a review of the NoS (nature of science) achieved. It used the non equivalent control group design and took place in the regions of Magelang and Pati, Province of Central Java, and the regions of Bantul and Sleman, Province of the Special Region of Yogyakarta. The research population consisted of students of the first and second grades at each junior high school chosen with research subjects sampled by means of cluster sampling. The instruments used included: a) an observation sheet, b) a written test, and c) a questionnaire. The learning and research instruments had been declared valid and reliable according to previous developmental research. In conclusion, the science learning based on local potential was effective in terms of all the NoS aspects.

Computerized Orders with Standardized Concentrations Decrease Dispensing Errors of Continuous Infusion Medications for Pediatrics

PubMed Central

Sowan, Azizeh K.; Vaidya, Vinay U.; Soeken, Karen L.; Hilmas, Elora

2010-01-01

OBJECTIVES The use of continuous infusion medications with individualized concentrations may increase the risk for errors in pediatric patients. The objective of this study was to evaluate the effect of computerized prescriber order entry (CPOE) for continuous infusions with standardized concentrations on frequency of pharmacy processing errors. In addition, time to process handwritten versus computerized infusion orders was evaluated and user satisfaction with CPOE as compared to handwritten orders was measured. METHODS Using a crossover design, 10 pharmacists in the pediatric satellite within a university teaching hospital were given test scenarios of handwritten and CPOE order sheets and asked to process infusion orders using the pharmacy system in order to generate infusion labels. Participants were given three groups of orders: five correct handwritten orders, four handwritten orders written with deliberate errors, and five correct CPOE orders. Label errors were analyzed and time to complete the task was recorded. RESULTS Using CPOE orders, participants required less processing time per infusion order (2 min, 5 sec ± 58 sec) compared with time per infusion order in the first handwritten order sheet group (3 min, 7 sec ± 1 min, 20 sec) and the second handwritten order sheet group (3 min, 26 sec ± 1 min, 8 sec), (p<0.01). CPOE eliminated all error types except wrong concentration. With CPOE, 4% of infusions processed contained errors, compared with 26% of the first group of handwritten orders and 45% of the second group of handwritten orders (p<0.03). Pharmacists were more satisfied with CPOE orders when compared with the handwritten method (p=0.0001). CONCLUSIONS CPOE orders saved pharmacists' time and greatly improved the safety of processing continuous infusions, although not all errors were eliminated. pharmacists were overwhelmingly satisfied with the CPOE orders PMID:22477811

Experimental analysis of the sheet metal forming behavior of newly developed press hardening steels

NASA Astrophysics Data System (ADS)

Meza-García, Enrique; Kräusel, Verena; Landgrebe, Dirk

2018-05-01

The aim of this work was the characterization of the newly developed press hardening sheet alloys 1800 PHS and 2000 PHS developed by SSAB with regard to their hot forming behavior on the basis of the experimental determination of relevant mechanical and technological properties. For this purpose conventional and non-conventional sheet metal testing methods were used. To determine the friction coefficient, the strip drawing test was applied, while the deep drawing cup test was used to determine the maximum draw depth. Finally, a V-bending test was carried out to evaluate the springback behavior of the investigated alloys by varying the blank temperature and quenching media. This work provides a technological guideline for the production of press hardened sheet parts made of these investigated sheet metals.

Double-Lap Shear Test For Honeycomb Core

NASA Technical Reports Server (NTRS)

Nettles, Alan T.; Hodge, Andrew J.

1992-01-01

Double-lap test measures shear strength of panel made of honeycomb core with 8-ply carbon-fiber/epoxy face sheets. Developed to overcome three principal disadvantages of prior standard single-lap shear test: specimen had to be more than 17 in. long; metal face sheets had to be used; and test introduced torque, with consequent bending and peeling of face sheets and spurious tensile or compressive loading of honeycomb.

Introduction to Agricultural Sales and Service. Teacher Edition.

ERIC Educational Resources Information Center

Kauer, Les

This Oklahoma curriculum guide contains 12 units. Each instructional unit includes some or all of these components: performance objectives, suggested activities, basic academic skills taxonomy, handouts, information sheets, supplements, transparency masters, activity sheets, assignment sheets, assignment sheet answers, job sheets, practical tests,…

Development of a written music-recognition system using Java and open source technologies

NASA Astrophysics Data System (ADS)

Loibner, Gernot; Schwarzl, Andreas; Kovač, Matthias; Paulus, Dietmar; Pölzleitner, Wolfgang

2005-10-01

We report on the development of a software system to recognize and interpret printed music. The overall goal is to scan printed music sheets, analyze and recognize the notes, timing, and written text, and derive the all necessary information to use the computers MIDI sound system to play the music. This function is primarily useful for musicians who want to digitize printed music for editing purposes. There exist a number of commercial systems that offer such a functionality. However, on testing these systems, we were astonished on how weak they behave in their pattern recognition parts. Although we submitted very clear and rather flawless scanning input, none of these systems was able to e.g. recognize all notes, staff lines, and systems. They all require a high degree of interaction, post-processing, and editing to get a decent digital version of the hard copy material. In this paper we focus on the pattern recognition area. In a first approach we tested more or less standard methods of adaptive thresholding, blob detection, line detection, and corner detection to find the notes, staff lines, and candidate objects subject to OCR. Many of the objects on this type of material can be learned in a training phase. None of the commercial systems we saw offers the option to train special characters or unusual signatures. A second goal in this project is to use a modern software engineering platform. We were interested in how well Java and open source technologies are suitable for pattern recognition and machine vision. The scanning of music served as a case-study.

12. "TEST STAND; STRUCTURAL; DEFLECTOR PIT DETAILS, SHEET NO. 1." ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

12. "TEST STAND; STRUCTURAL; DEFLECTOR PIT DETAILS, SHEET NO. 1." Specifications No. ENG-04-353-55-72; Drawing No. 60-09-12; sheet 41 of 148; file no. 1320/92, Rev. A. Stamped: RECORD DRAWING - AS CONSTRUCTED. Below stamp: Contract no. 4338, no change. - Edwards Air Force Base, Air Force Rocket Propulsion Laboratory, Test Stand 1-A Terminal Room, Test Area 1-120, north end of Jupiter Boulevard, Boron, Kern County, CA

Ice sheet altimetry

NASA Technical Reports Server (NTRS)

Brooks, R. L.

1981-01-01

Generalized surface slopes were computed for the Antarctic and Greenland ice sheets by differencing plotted contour levels and dividing them by the distance between the contours. It was observed that more than 90% of the ice sheets have surface slopes less than 1%. Seasat test mode-1 Seasat altimeter measurements over Greenland were analyzed by comparisons with collinear and intersecting normal mode Seasat altimeter passes. Over the ice sheet, the computed surface elevations from test mode-1 measurements were consistently lower by about 45 m and the AGC levels were down by approximately 6 dB. No test mode-1 data were acquired over Antarctica. It is concluded that analysis of the existing altimeter data base over the two ice sheets is crucial in designing a future improved altimeter tracking capability. It is recommended that additional waveform retracking be performed to characterize ice sheet topography as a function of geographic area and elevation.

Analysis of the RPE sheet in the rd10 retinal degeneration model

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jiang, Yi

2011-01-04

The normal RPE sheet in the C57Bl/6J mouse is subclassified into two major tiling patterns: A regular generally hexagonal array covering most of the surface and a 'soft network' near the ciliary body made of irregularly shaped cells. Physics models predict these two patterns based on contractility and elasticity of the RPE cell, and strength of cellular adhesion between cells. We hypothesized and identified major changes in RPE regular hexagonal tiling pattern in rdl0 compared to C57BL/6J mice. RPE sheet damage was extensive but occurred in rd10 later than expected, after most retinal degeneration. RPE sheet changes occur in zonesmore » with a bullseye pattern. In the posterior zone around the optic nerve RPE cells take on larger irregular and varied shapes to form an intact monolayer. In mid periphery, there is a higher than normal density of cells that progress into involuted layers of RPE under the retina. The periphery remains mostly normal until late stages of degeneration. The number of neighboring cells varies widely depending on zone and progression. RPE morphology continues to deteriorate long after the photoreceptors have degenerated. The RPE cells are bystanders to the rd10 degeneration within photo receptors, and the collateral damage to the RPE sheet resembles stimulation of migration or chemotaxis. Quantitative measures of the tiling patterns and histopathology detected here, scripted in a pipeline written in Perl and Cell Profiler (an open source Matlab plugin), are directly applicable to RPE sheet images from noninvasive fundus autofluorescence (FAF), adaptive optics confocal scanning laser ophthalmoscope (AO-cSLO), and spectral domain optical coherence tomography (SD-OCT) of patients with early stage AMD or RP.« less

Introduction to Production/Manufacturing Drafting. Drafting Module 8. Instructor's Guide.

ERIC Educational Resources Information Center

Missouri Univ., Columbia. Instructional Materials Lab.

This module, 1 of 10 in the Drafting curriculum guide developed in Missouri, contains 3 units of study that include some or all of the following components: performance objectives, lesson plans, information sheets, transparency masters, handouts, assignment sheets, job sheets, a unit test, and answers to the unit test. Special instructions on…

Checkout and Standard Use Procedures for the Mark III Space Suit Assembly

NASA Technical Reports Server (NTRS)

Valish, Dana J.

2012-01-01

The operational pressure range is the range to which the suit can be nominally operated for manned testing. The top end of the nominal operational pressure range is equivalent to 1/2 the proof pressure. Structural pressure is 1.5 times the specified test pressure for any given test. Proof pressure is the maximum unmanned pressure to which the suit was tested by the vendor prior to delivery. The maximum allowable working pressure (MAWP) is 90% of the proof pressure. The pressure systems RVs are set to keep components below their MAWPs. If the suit is pressurized over its MAWP, the suit will be taken out of service and an in-depth inspection/review of the suit will be performed before the suit is put back in service. The procedures outlined in this document should be followed as written. However, the suit test engineer (STE) may make redline changes real-time, provided those changes are recorded in the anomaly section of the test data sheet. If technicians supporting suit build-up, check-out, and/or test execution believe that a procedure can be improved, they should notify their lead. If procedures are incorrect to the point of potentially causing hardware damage or affecting safety, bring the problem to the technician lead and/or STE s attention and stop work until a solution (temporary or permanent) is authorized. Certain steps in the procedure are marked with a DV , for Designated Verifier. The Designated Verifier for this procedure is an Advanced Space Suit Technology Development Laboratory technician, not directly involved in performing the procedural steps, who will verify that the step was performed as stated. The steps to be verified by the DV were selected based on one or more of the following criteria: the step was deemed significant in ensuring the safe performance of the test, the data recorded in the step is of specific interest in monitoring the suit system operation, or the step has a strong influence on the successful completion of test objectives. Prior to all manned test activities, Advanced Suit Test Data Sheet (TDS) Parts A-E shall be completed to verify system and team are ready for test. Advanced Suit TDS Parts F-G shall be completed at the end of the suited activity. Appendix B identifies tha appropriate Mark III suit emergency event procedures.

Design and fabrication of titanium multi-wall Thermal Protection System (TPS) test panels

NASA Technical Reports Server (NTRS)

Blair, W.; Meaney, J. E., Jr.; Rosenthal, H. A.

1980-01-01

A titanium multiwall thermal protection system panel was designed. The panel is a nine sheet sandwich structure consisting of an upper and lower face sheet; four dimpled sheets, three septum sheets, and clips for attachment to a vehicle structure. An acceptable fabrication process was developed, and the panel design was verified through mechanical and thermal testing of component specimens. A design was completed which takes into consideration fabrication techniques, thermal properties, mechanical properties, and materials availability.

The mechanical behavior of cross-rolled beryllium sheet

NASA Technical Reports Server (NTRS)

Henkener, J. A.; Spiker, I. K.; Castner, W. L.

1992-01-01

In response to the failure of a conical section of the Insat C satellite during certification testing, the use of beryllium for payload structures, particularly in sheet product form, is being reevaluated. A test program was initiated to study the tensile, shear, and out-of-plane failure modes of beryllium cross-rolled sheet and to apply data to the development of an appropriate failure criterion. Tensile test results indicated that sanding the surface of beryllium sheet has no significant effect on yield strength but can produce a profound reduction in ultimate strength and results obtained by finite element analysis. Critical examination of these test results may contribute to the modification of a JSC policy for the use of beryllium in orbiter and payload structures.

Crib sheets or security blankets?

PubMed

Drake, V K; Freed, P; Hunter, J M

1998-01-01

This article describes the sanctioned use of crib sheets as a nursing intervention to decrease test anxiety when the classroom is the practice setting for psychiatric/mental health nursing faculty. The products that the students created offered additional unsuspected benefits. The faculty were convinced that the use of crib sheets can be a sound intervention to reduce students' test-taking anxiety.

16 CFR 1632.3 - General requirements.

Code of Federal Regulations, 2011 CFR

2011-01-01

...) Summary of test method. The method measures the ignition resistance of a mattress or mattress pad by... surface. A two-sheet test is also conducted on similar surface locations. In the latter test, the burning cigarettes are placed between the sheets. (b) Test criterion. When testing the mattress or mattress pad...

16 CFR 1632.3 - General requirements.

Code of Federal Regulations, 2010 CFR

2010-01-01

...) Summary of test method. The method measures the ignition resistance of a mattress or mattress pad by... surface. A two-sheet test is also conducted on similar surface locations. In the latter test, the burning cigarettes are placed between the sheets. (b) Test criterion. When testing the mattress or mattress pad...

16 CFR 1632.3 - General requirements.

Code of Federal Regulations, 2014 CFR

2014-01-01

...) Summary of test method. The method measures the ignition resistance of a mattress or mattress pad by... surface. A two-sheet test is also conducted on similar surface locations. In the latter test, the burning cigarettes are placed between the sheets. (b) Test criterion. When testing the mattress or mattress pad...

16 CFR 1632.3 - General requirements.

Code of Federal Regulations, 2012 CFR

2012-01-01

...) Summary of test method. The method measures the ignition resistance of a mattress or mattress pad by... surface. A two-sheet test is also conducted on similar surface locations. In the latter test, the burning cigarettes are placed between the sheets. (b) Test criterion. When testing the mattress or mattress pad...

Production development of organic nonflammable spacecraft potting, encapsulating and conformal coating compounds. Volume 3: Appendices

NASA Technical Reports Server (NTRS)

Lieberman, S. L.

1974-01-01

Appendices are presented which include: statement of work; material vendor contacts; formulation/processing data sheet; upward propagation test; flammability test conditions/results sheet; odor test; vacuum stability requirements; flammability test facility; determination of offgassing products and carbon monoxide test; and pneumatic and mechanical impact test guidelines.

49 CFR 180.215 - Reporting and record retention requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

..., as well as unsuccessful tests. The entry for a second test after a failure to hold test pressure must..., pressure test, and ultrasonic examination if permitted under a special permit, as applicable, must be... each test sheet, provided each test on the sheet was conducted on that date. Ditto marks or a solid...

Skiving stacked sheets of paper into test paper for rapid and multiplexed assay

PubMed Central

Yang, Mingzhu; Zhang, Wei; Yang, Junchuan; Hu, Binfeng; Cao, Fengjing; Zheng, Wenshu; Chen, Yiping; Jiang, Xingyu

2017-01-01

This paper shows that stacked sheets of paper preincubated with different biological reagents and skiving them into uniform test paper sheets allow mass manufacturing of multiplexed immunoassay devices and simultaneous detection of multiplex targets that can be read out by a barcode scanner. The thickness of one sheet of paper can form the width of a module for the barcode; when stacked, these sheets of paper can form a series of barcodes representing the targets, depending on the color contrast provided by a colored precipitate of an immunoassay. The uniform thickness of sheets of paper allows high-quality signal readout. The manufacturing method allows highly efficient fabrication of the materials and substrates for a straightforward assay of targets that range from drugs of abuse to biomarkers of blood-transmitted infections. In addition, as a novel alternative to the conventional point-of-care testing method, the paper-based barcode assay system can provide highly efficient, accurate, and objective diagnoses. PMID:29214218

The effect of mesenchymal stem cell sheets on structural allograft healing of critical-sized femoral defects in mice

PubMed Central

Long, Teng; Zhu, Zhenan; Awad, Hani A.; Schwarz, Edward M.; Hilton, Matthew J.; Dong, Yufeng

2014-01-01

Structural bone allografts are widely used in the clinic to treat critical sized bone defects, despite lacking the osteoinductive characteristics of live autografts. To address this, we generated revitalized structural allografts wrapped with mesenchymal stem/progenitor cell (MSC) sheets, which were produced by expanding primary syngenic bone marrow derived cells on temperature-responsive plates, as a tissue engineered periosteum. In vitro assays demonstrated maintenance of the MSC phenotype in the sheets, suggesting that short-term culturing of MSC sheets is not detrimental. To test their efficacy in vivo, allografts wrapped with MSC sheets were transplanted into 4-mm murine femoral defects and compared to allografts with direct seeding of MSCs and allografts without cells. Evaluations consisted of x-ray plain radiography, 3D microCT, histology, and biomechanical testing at 4- and 6-weeks post-surgery. Our findings demonstrate that MSC sheets induce prolonged cartilage formation at the graft-host junction and enhanced bone callus formation, as well as graft-host osteointegration. Moreover, a large periosteal callus was observed spanning the allografts with MSC sheets, which partially mimics live autograft healing. Finally, biomechanical testing showed a significant increase in the structural and functional properties of MSC sheet grafted femurs. Taken together, MSC sheets exhibit enhanced osteogenicity during critical sized bone defect repair, demonstrating the feasibility of this tissue engineering solution for massive allograft healing. PMID:24393269

Utilization of a Biodegradable Mulch Sheet Produced from Poly(Lactic Acid)/Ecoflex®/Modified Starch in Mandarin Orange Groves

PubMed Central

Tachibana, Yuya; Maeda, Takuya; Ito, Osamu; Maeda, Yasukatsu; Kunioka, Masao

2009-01-01

We have developed a mulch sheet made by inflation molding of PLA, Ecoflex® and modified starch, which all have different biodegradabilities. A field test of use as an agricultural mulch sheet for mandarin oranges was carried out over two years. The mechanical properties of the mulch sheet were weakened with time during the field test, but the quality of the mandarin oranges increased, a result of the controlled degradation of the sheet. The most degradable modified starch degraded first, allowing control of the moisture on the soil. Accelerator mass spectroscopy was used for evaluation of the biomass carbon ratio. The biomass carbon ratio decreased by degradation of the biobased materials, PLA and modified starch in the mulch sheet. PMID:19812715

Do You Prefer to Have the Text or a Sheet with Your Physics Exams?

NASA Astrophysics Data System (ADS)

Hamed, Kastro M.

2008-05-01

Many high school and introductory college physics instructors ponder the choice between "open text" exams versus "facts and formulae sheet" exams. Other alternatives are closed book/closed notes exams or an instructor-prepared sheet of facts and relevant formulas. There is no agreement on merit. Rehfuss strongly opposes allowing students to use formula sheets while taking physics exams despite acknowledging that such use is common practice. Cone2 responded to Rehfuss by defending the use of such sheets and outlining the benefits of a "cheat sheet." Debate over the use of a "cheat sheet" or other resources during exams is not limited to the physics community. Skidmore and Aagaard3 studied the relationship between testing conditions and student test scores for students in teacher education. Two decades earlier Boniface,4 Dorsal and Cundiff,5 and Hindman6 published papers on the use of texts and/or sheets during examinations in psychology and education. Others, such as Pullen et al.7 focused on studying the discarded cheat sheets themselves. Humorously, in October 2005 The New York Times8 reported an unusual museum exhibit of "cheat sheets" and the different ways students had cheated at a particular university.

Benchmark Testing of the Largest Titanium Aluminide Sheet Subelement Conducted

NASA Technical Reports Server (NTRS)

Bartolotta, Paul A.; Krause, David L.

2000-01-01

To evaluate wrought titanium aluminide (gamma TiAl) as a viable candidate material for the High-Speed Civil Transport (HSCT) exhaust nozzle, an international team led by the NASA Glenn Research Center at Lewis Field successfully fabricated and tested the largest gamma TiAl sheet structure ever manufactured. The gamma TiAl sheet structure, a 56-percent subscale divergent flap subelement, was fabricated for benchmark testing in three-point bending. Overall, the subelement was 84-cm (33-in.) long by 13-cm (5-in.) wide by 8-cm (3-in.) deep. Incorporated into the subelement were features that might be used in the fabrication of a full-scale divergent flap. These features include the use of: (1) gamma TiAl shear clips to join together sections of corrugations, (2) multiple gamma TiAl face sheets, (3) double hot-formed gamma TiAl corrugations, and (4) brazed joints. The structural integrity of the gamma TiAl sheet subelement was evaluated by conducting a room-temperature three-point static bend test.

16 CFR § 1632.3 - General requirements.

Code of Federal Regulations, 2013 CFR

2013-01-01

... General requirements. (a) Summary of test method. The method measures the ignition resistance of a... the mattress or mattress pad surface. A two-sheet test is also conducted on similar surface locations. In the latter test, the burning cigarettes are placed between the sheets. (b) Test criterion. When...

Improved perception of communication and compliance with a revised, intensive care unit-specific bedside communication sheet.

PubMed

Aponte-Patel, Linda; Sen, Anita

2015-01-01

Although many pediatric intensive care units (PICUs) use beside communication sheets (BCSs) to highlight daily goals, the optimal format is unknown. A site-specific BCS could improve both PICU communication and compliance completing the BCS. Via written survey, PICU staff at an academic children's hospital provided recommendations for improving and revising an existing BCS. Pre- and post-BCS revision, PICU staff were polled regarding PICU communication and BCS effectiveness, and daily compliance for completing the BCS was monitored. After implementation of the revised BCS, staff reporting "excellent" or "very good" day-to-day communication within the PICU increased from 57% to 77% (P = .02). Compliance for completing the BCS also increased significantly (75% vs 83%, P = .03). Introduction of a focused and concise BCS tailored to a specific PICU leads to improved perceptions of communication by PICU staff and increased compliance completing the daily BCS. © The Author(s) 2014.

An audit of the quality of operation notes in an otolaryngology unit.

PubMed

Bateman, N D; Carney, A S; Gibbin, K P

1999-04-01

Hand-written operation notes are often produced as evidence in medico-legal cases. Incomplete and illegible notes, along with the use of confusing abbreviations, are a common source of weakness in a surgeon's defence. An audit of 100 sets of operation notes was carried out in a single otolaryngology department. Notes were scrutinised for the accuracy of data, ward, department and name of surgeon, as well as for the inclusion of unacceptable abbreviations. Using an aide-memoire attached to the front of the operation sheet, the audit was repeated with identical criteria. The aide-memoire improved the standard of operation note with respect to all measured criteria. Clear identification of operating surgeon improved from 74% to 93%, and the avoidance of unacceptable abbreviations rose from 53% to 84%. We conclude that a simple aide-memoire attached to operation note sheets can significantly improve the quality of note-keeping and potentially avoid medico-legal problems.

Multi-Objective Parallel Test-Sheet Composition Using Enhanced Particle Swarm Optimization

ERIC Educational Resources Information Center

Ho, Tsu-Feng; Yin, Peng-Yeng; Hwang, Gwo-Jen; Shyu, Shyong Jian; Yean, Ya-Nan

2009-01-01

For large-scale tests, such as certification tests or entrance examinations, the composed test sheets must meet multiple assessment criteria. Furthermore, to fairly compare the knowledge levels of the persons who receive tests at different times owing to the insufficiency of available examination halls or the occurrence of certain unexpected…

Sensing sheets based on large area electronics for fatigue crack detection

NASA Astrophysics Data System (ADS)

Yao, Yao; Glisic, Branko

2015-03-01

Reliable early-stage damage detection requires continuous structural health monitoring (SHM) over large areas of structure, and with high spatial resolution of sensors. This paper presents the development stage of prototype strain sensing sheets based on Large Area Electronics (LAE), in which thin-film strain gauges and control circuits are integrated on the flexible electronics and deposited on a polyimide sheet that can cover large areas. These sensing sheets were applied for fatigue crack detection on small-scale steel plates. Two types of sensing-sheet interconnects were designed and manufactured, and dense arrays of strain gauge sensors were assembled onto the interconnects. In total, four (two for each design type) strain sensing sheets were created and tested, which were sensitive to strain at virtually every point over the whole sensing sheet area. The sensing sheets were bonded to small-scale steel plates, which had a notch on the boundary so that fatigue cracks could be generated under cyclic loading. The fatigue tests were carried out at the Carleton Laboratory of Columbia University, and the steel plates were attached through a fixture to the loading machine that applied cyclic fatigue load. Fatigue cracks then occurred and propagated across the steel plates, leading to the failure of these test samples. The strain sensor that was close to the notch successfully detected the initialization of fatigue crack and localized the damage on the plate. The strain sensor that was away from the crack successfully detected the propagation of fatigue crack based on the time history of measured strain. Overall, the results of the fatigue tests validated general principles of the strain sensing sheets for crack detection.

Communication failures in patient sign-out and suggestions for improvement: a critical incident analysis.

PubMed

Arora, V; Johnson, J; Lovinger, D; Humphrey, H J; Meltzer, D O

2005-12-01

The transfer of care for hospitalized patients between inpatient physicians is routinely mediated through written and verbal communication or "sign-out". This study aims to describe how communication failures during this process can lead to patient harm. In interviews employing critical incident technique, first year resident physicians (interns) described (1) any adverse events or near misses due to suboptimal preceding patient sign-out; (2) the worst event due to suboptimal sign-out in which they were involved; and (3) suggestions to improve sign-out. All data were analyzed and categorized using the constant comparative method with independent review by three researchers. Twenty six interns caring for 82 patients were interviewed after receiving sign-out from another intern. Twenty five discrete incidents, all the result of communication failures during the preceding patient sign-out, and 21 worst events were described. Inter-rater agreement for categorization was high (kappa 0.78-1.00). Omitted content (such as medications, active problems, pending tests) or failure-prone communication processes (such as lack of face-to-face discussion) emerged as major categories of failed communication. In nearly all cases these failures led to uncertainty during decisions on patient care. Uncertainty may result in inefficient or suboptimal care such as repeat or unnecessary tests. Interns desired thorough but relevant face-to-face verbal sign-outs that reviewed anticipated issues. They preferred legible, accurate, updated, written sign-out sheets that included standard patient content such as code status or active and anticipated medical problems. Communication failures during sign-out often lead to uncertainty in decisions on patient care. These may result in inefficient or suboptimal care leading to patient harm.

The effect of mesenchymal stem cell sheets on structural allograft healing of critical sized femoral defects in mice.

PubMed

Long, Teng; Zhu, Zhenan; Awad, Hani A; Schwarz, Edward M; Hilton, Matthew J; Dong, Yufeng

2014-03-01

Structural bone allografts are widely used in the clinic to treat critical sized bone defects, despite lacking the osteoinductive characteristics of live autografts. To address this, we generated revitalized structural allografts wrapped with mesenchymal stem/progenitor cell (MSC) sheets, which were produced by expanding primary syngenic bone marrow derived cells on temperature-responsive plates, as a tissue-engineered periosteum. In vitro assays demonstrated maintenance of the MSC phenotype in the sheets, suggesting that short-term culturing of MSC sheets is not detrimental. To test their efficacy in vivo, allografts wrapped with MSC sheets were transplanted into 4-mm murine femoral defects and compared to allografts with direct seeding of MSCs and allografts without cells. Evaluations consisted of X-ray plain radiography, 3D microCT, histology, and biomechanical testing at 4- and 6-weeks post-surgery. Our findings demonstrate that MSC sheets induce prolonged cartilage formation at the graft-host junction and enhanced bone callus formation, as well as graft-host osteointegration. Moreover, a large periosteal callus was observed spanning the allografts with MSC sheets, which partially mimics live autograft healing. Finally, biomechanical testing showed a significant increase in the structural and functional properties of MSC sheet grafted femurs. Taken together, MSC sheets exhibit enhanced osteogenicity during critical sized bone defect repair, demonstrating the feasibility of this tissue engineering solution for massive allograft healing. Copyright © 2013 Elsevier Ltd. All rights reserved.

Promoting Metacognition in Introductory Calculus-based Physics Labs

NASA Astrophysics Data System (ADS)

Grennell, Drew; Boudreaux, Andrew

2010-10-01

In the Western Washington University physics department, a project is underway to develop research-based laboratory curriculum for the introductory calculus-based course. Instructional goals not only include supporting students' conceptual understanding and reasoning ability, but also providing students with opportunities to engage in metacognition. For the latter, our approach has been to scaffold reflective thinking with guided questions. Specific instructional strategies include analysis of alternate reasoning presented in fictitious dialogues and comparison of students' initial ideas with their lab group's final, consensus understanding. Assessment of student metacognition includes pre- and post- course data from selected questions on the CLASS survey, analysis of written lab worksheets, and student opinion surveys. CLASS results are similar to a traditional physics course and analysis of lab sheets show that students struggle to engage in a metacognitive process. Future directions include video studies, as well as use of additional written assessments adapted from educational psychology.

New Modelling of Localized Necking in Sheet Metal Stretching

NASA Astrophysics Data System (ADS)

Bressan, José Divo

2011-01-01

Present work examines a new mathematical model to predict the onset of localized necking in the industrial processes of sheet metal forming such as biaxial stretching. Sheet metal formability is usually assessed experimentally by testing such as the Nakajima test to obtain the Forming Limit Curve, FLC, which is an essential material parameter necessary to numerical simulations by FEM. The Forming Limit Diagram or "Forming Principal Strain Map" shows the experimental FLC which is the plot of principal true strains in the sheet metal surface, ɛ1 and ɛ2, occurring at critical points obtained in laboratory formability tests or in the fabrication process. Two types of undesirable rupture mechanisms can occur in sheet metal forming products: localized necking and shear induced fracture. Therefore, two kinds of limit strain curves can be plotted: the local necking limit curve FLC-N and the shear fracture limit curve FLC-S. Localized necking is theoretically anticipated to initiate at a thickness defect ƒin = hib/hia inside the grooved sheet thickness hia, but only at the instability point of maximum load. The inception of grooving on the sheet surface evolves from instability point to localized necking and final rupture, during further sheet metal straining. Work hardening law is defined for a strain and strain rate material by the effective stress σ¯ = σo(1+βɛ¯)n???ɛM. The average experimental hardening law curve for tensile tests at 0°, 45° and 90°, assuming isotropic plasticity, was used to analyze the plasticity behavior during the biaxial stretching of sheet metals. Theoretical predicted curves of local necking limits are plotted in the positive quadrant of FPSM for different defect values ƒin and plasticity parameters. Limit strains are obtained from a software developed by the author. Some experimental results of forming limit curve obtained from experiments for IF steel sheets are compared with the theoretical predicted curves: the correlation is good.

Test of superplastically formed corrugated aluminum compression specimens with beaded webs

NASA Technical Reports Server (NTRS)

Davis, Randall C.; Royster, Dick M.; Bales, Thomas T.; James, William F.; Shinn, Joseph M., Jr.

1991-01-01

Corrugated wall sections provide a highly efficient structure for carrying compressive loads in aircraft and spacecraft fuselages. The superplastic forming (SPF) process offers a means to produce complex shells and panels with corrugated wall shapes. A study was made to investigate the feasibility of superplastically forming 7475-T6 aluminum sheet into a corrugated wall configuration and to demonstrate the structural integrity of the construction by testing. The corrugated configuration selected has beaded web segments separating curved-cap segments. Eight test specimens were fabricated. Two specimens were simply a single sheet of aluminum superplastically formed to a beaded-web, curved-cap corrugation configuration. Six specimens were single-sheet corrugations modified by adhesive bonding additional sheet material to selectively reinforce the curved-cap portion of the corrugation. The specimens were tested to failure by crippling in end compression at room temperature.

A Randomized Rounding Approach for Optimization of Test Sheet Composing and Exposure Rate Control in Computer-Assisted Testing

ERIC Educational Resources Information Center

Wang, Chu-Fu; Lin, Chih-Lung; Deng, Jien-Han

2012-01-01

Testing is an important stage of teaching as it can assist teachers in auditing students' learning results. A good test is able to accurately reflect the capability of a learner. Nowadays, Computer-Assisted Testing (CAT) is greatly improving traditional testing, since computers can automatically and quickly compose a proper test sheet to meet user…

Laser Indirect Shock Welding of Fine Wire to Metal Sheet.

PubMed

Wang, Xiao; Huang, Tao; Luo, Yapeng; Liu, Huixia

2017-09-12

The purpose of this paper is to present an advanced method for welding fine wire to metal sheet, namely laser indirect shock welding (LISW). This process uses silica gel as driver sheet to accelerate the metal sheet toward the wire to obtain metallurgical bonding. A series of experiments were implemented to validate the welding ability of Al sheet/Cu wire and Al sheet/Ag wire. It was found that the use of a driver sheet can maintain high surface quality of the metal sheet. With the increase of laser pulse energy, the bonding area of the sheet/wire increased and the welding interfaces were nearly flat. Energy dispersive spectroscopy (EDS) results show that the intermetallic phases were absent and a short element diffusion layer which would limit the formation of the intermetallic phases emerging at the welding interface. A tensile shear test was used to measure the mechanical strength of the welding joints. The influence of laser pulse energy on the tensile failure modes was investigated, and two failure modes, including interfacial failure and failure through the wire, were observed. The nanoindentation test results indicate that as the distance to the welding interface decreased, the microhardness increased due to the plastic deformation becoming more violent.

10 CFR 55.40 - Implementation.

Code of Federal Regulations, 2010 CFR

2010-01-01

... REGULATORY COMMISSION (CONTINUED) OPERATORS' LICENSES Written Examinations and Operating Tests § 55.40... Standards for Power Reactors,” 1 in effect six months before the examination date to prepare the written... also use the criteria in NUREG-1021 to evaluate the written examinations and operating tests prepared...

10 CFR 55.40 - Implementation.

Code of Federal Regulations, 2013 CFR

2013-01-01

... REGULATORY COMMISSION (CONTINUED) OPERATORS' LICENSES Written Examinations and Operating Tests § 55.40... Standards for Power Reactors,” 1 in effect six months before the examination date to prepare the written... also use the criteria in NUREG-1021 to evaluate the written examinations and operating tests prepared...

10 CFR 55.40 - Implementation.

Code of Federal Regulations, 2012 CFR

2012-01-01

... REGULATORY COMMISSION (CONTINUED) OPERATORS' LICENSES Written Examinations and Operating Tests § 55.40... Standards for Power Reactors,” 1 in effect six months before the examination date to prepare the written... also use the criteria in NUREG-1021 to evaluate the written examinations and operating tests prepared...

10 CFR 55.40 - Implementation.

Code of Federal Regulations, 2011 CFR

2011-01-01

... REGULATORY COMMISSION (CONTINUED) OPERATORS' LICENSES Written Examinations and Operating Tests § 55.40... Standards for Power Reactors,” 1 in effect six months before the examination date to prepare the written... also use the criteria in NUREG-1021 to evaluate the written examinations and operating tests prepared...

10 CFR 55.40 - Implementation.

Code of Federal Regulations, 2014 CFR

2014-01-01

... REGULATORY COMMISSION (CONTINUED) OPERATORS' LICENSES Written Examinations and Operating Tests § 55.40... Standards for Power Reactors,” 1 in effect six months before the examination date to prepare the written... also use the criteria in NUREG-1021 to evaluate the written examinations and operating tests prepared...

Patient representatives' views on patient information in clinical cancer trials.

PubMed

Dellson, Pia; Nilbert, Mef; Carlsson, Christina

2016-02-01

Patient enrolment into clinical trials is based on oral information and informed consent, which includes an information sheet and a consent certificate. The written information should be complete, but at the same time risks being so complex that it may be questioned if a fully informed consent is possible to provide. We explored patient representatives' views and perceptions on the written trial information used in clinical cancer trials. Written patient information leaflets used in four clinical trials for colorectal cancer were used for the study. The trials included phase I-III trials, randomized and non-randomized trials that evaluated chemotherapy/targeted therapy in the neoadjuvant, adjuvant and palliative settings. Data were collected through focus groups and were analysed using inductive content analysis. Two major themes emerged: emotional responses and cognitive responses. Subthemes related to the former included individual preferences and perceptions of effect, while subthemes related to the latter were comprehensibility and layout. Based on these observations the patient representatives provided suggestions for improvement, which largely included development of future simplified and more attractive informed consent forms. The emotional and cognitive responses to written patient information reported by patient representatives provides a basis for revised formats in future trials and add to the body of information that support use of plain language, structured text and illustrations to improve the informed consent process and thereby patient enrolment into clinical trials.

Analytical and experimental investigation of fatigue in a sheet specimen with an interference-fit bolt

NASA Technical Reports Server (NTRS)

Crews, J. H., Jr.

1975-01-01

A fatigue analysis, based on finite-element calculations and fatigue tests, was conducted for an aluminum-alloy sheet specimen with a steel interference-fit bolt. The stress analysis of the region near the bolt hole showed that the beneficial effect of an interference-fit bolt can be interpreted as the combined result of two effects: (1) load transfer through the bolt and (2) the compressive interference stresses in the sheet. Results of the fatigue tests show that progressively higher interference levels produced longer fatigue lives. The tests also show that a high level of interference prevents fretting at the bolt-sheet interface and that interferences larger than this level produced little additional improvement in fatigue life.

Solid-state and fusion resistance spot welding of TD-NiCr sheet

NASA Technical Reports Server (NTRS)

Moore, T. J.

1973-01-01

By using specially processed TD-NiCr sheet in both 0.4-mm (0.015-in.) and 1.6-mm (0.062-in.) thicknesses and carefully selected welding procedures, solid state resistance spot welds were produced which, after postheating at 1200 C, were indistinguishable from the parent material. Stress-rupture shear tests of single-spot lap joints in 0.4-mm (0.015-in.) thick sheet showed that these welds were as strong as the parent material. Similar results were obtained in tensile-shear tests at room temperature and 1100 C and in fatigue tests. Conventional fusion spot welds in commercial sheet were unsatisfactory because of poor stress-rupture shear properties resulting from metallurgical damage to the parent material.

Written reflection in an eHealth intervention for adults with type 2 diabetes mellitus: a qualitative study.

PubMed

Lie, Silje S; Karlsen, Bjørg; Niemiec, Christopher P; Graue, Marit; Oftedal, Bjørg

2018-01-01

Individuals with type 2 diabetes mellitus (T2DM) are responsible for the daily decisions and actions necessary to manage their disease, which makes self-management the cornerstone of diabetes care. Many patients do not reach recommended treatment goals, and thus it is important to develop and evaluate innovative interventions that facilitate optimal motivation for adequate self-management of T2DM. The aim of the current study was to explore how adults with T2DM experience using reflection sheets to stimulate written reflection in the context of the Guided Self-Determination (GSD) eHealth intervention and how written reflection might affect their motivation for self-management of T2DM. We used a qualitative design in which data were collected through individual interviews. The sample consisted of 10 patients who completed the GSD eHealth intervention, and data were analyzed using qualitative content analysis. The qualitative content analysis yielded 2 main themes. We labeled the first theme as "Written reflection affects awareness and commitment in diabetes self-management", which reflects 2 subthemes, namely, "Writing creates space and time for autonomous reflection" and "Writing influences individuals' focus in diabetes self-management". We labeled the second theme as "Written reflection is perceived as inapplicable in diabetes self-management", which reflects 2 subthemes, namely, "Responding in writing is difficult" and "The timing of the writing is inappropriate". Our findings indicate that written reflection in the context of the GSD eHealth intervention may be conducive to motivation for diabetes self-management for some patients. However, it seems that in-person consultation with the diabetes nurse may be necessary to achieve the full potential benefit of the GSD as an eHealth intervention. We advocate further development and examination of the GSD as a "blended" approach, especially for those who consider written reflection to be difficult or unfamiliar.

A Microsample Tensile Test Application: Local Strength of Impact Welds Between Sheet Metals

NASA Astrophysics Data System (ADS)

Benzing, J. T.; He, M.; Vivek, A.; Taber, G. A.; Mills, M. J.; Daehn, G. S.

2017-03-01

Microsample tensile testing was conducted to evaluate the quality of impact welds created by vaporizing foil actuator welding. Tensile test samples with a gauge length of 0.6 mm were electro-discharge machined out of welds created between 1-mm-thick aluminum alloy type 6061 (AA6061) sheets and 6-mm-thick copper (Cu110) plates. Aluminum sheets were used as flyers, while copper plates acted as targets. Flyer sheets in T6 as well as T4 temper conditions were utilized to create welds. Some of the welds made with T4 temper flyers were heat treated to a T6 temper. It was found that the welds made with T4 temper flyers were slightly stronger (max. of 270 MPa) than those produced with T6 temper flyers. Generally, failure propagated in a brittle manner across the weld interface; however, elemental mapping reveals material transfer on either member of the welded system. This work proves the feasibility to apply microsample tensile testing to assess impact welding, even when conducted with flyer sheets of 1 mm or less, and provides insight that is complementary to other test methods.

Readability of neurosurgery-related patient education materials provided by the American Association of Neurological Surgeons and the National Library of Medicine and National Institutes of Health.

PubMed

Schmitt, Paul J; Prestigiacomo, Charles J

2013-11-01

Most professional organizations now provide patient information material, and not all of this material is appropriate for the average American adult to comprehend. The National Institutes of Health (NIH) and the United States Department of Health and Human Services recommend that patient education materials be written at the sixth-grade level. Our aim was to assess the readability of neurosurgery-related patient education material and compare it with The American Medical Association, NIH, and United States Department of Health and Human Services recommendations. Materials provided by the American Association of Neurologic Surgeons (AANS) and the U.S. National Library of Medicine (NLM) and National Institutes of Health were assessed with the Flesch-Kincaid grade level and Flesch Reading Ease score with Microsoft Office Word software. None of the articles had Flesch-Kincaid grade levels at or below the sixth-grade level. All articles on the AANS Conditions and Treatments section were written at or above the ninth-grade level; three of the AANS Camera-Ready Fact Sheets and four of the NIH/NLM articles were written between the seventh- and eighth-grade levels. Current patient education material provided by the AANS is written well above the recommended level. Material from the NLM and NIH performed better, but was still above the recommended sixth-grade level. Education materials should contain information relevant to patients' conditions, be accurate in the information they present, and be written with the average patient in mind. Copyright © 2013 Elsevier Inc. All rights reserved.

Evaluation of the Transient Liquid Phase (TLP) Bonding Process for Ti3Al-Based Honeycomb Core Sandwich Structure

NASA Technical Reports Server (NTRS)

Bird, R. Keith; Hoffman, Eric K.

1998-01-01

The suitability of using transient liquid phase (TLP) bonding to fabricate honeycomb core sandwich panels with Ti-14Al-21Nb (wt%) titanium aluminide (T3Al) face sheets for high-temperature hypersonic vehicle applications was evaluated. Three titanium alloy honeycomb cores and one Ti3Al alloy honeycomb core were investigated. Edgewise compression (EWC) and flatwise tension (FWT) tests on honeycomb core sandwich specimens and tensile tests of the face sheet material were conducted at temperatures ranging from room temperature to 1500 F. EWC tests indicated that the honeycomb cores and diffusion bonded joints were able to stabilize the face sheets up to and beyond the face sheet compressive yield strength for all temperatures investigated. The specimens with the T3Al honeycomb core produced the highest FWT strengths at temperatures above 1000 F. Tensile tests indicated that TLP processing conditions resulted in decreases in ductility of the Ti-14Al-21Nb face sheets. Microstructural examination showed that the side of the face sheets to which the filler metals had been applied was transformed from equiaxed alpha2 grains to coarse plates of alpha2 with intergranular Beta. Fractographic examination of the tensile specimens showed that this transformed region was dominated by brittle fracture.

Property Criteria for Automotive Al-Mg-Si Sheet Alloys

PubMed Central

Prillhofer, Ramona; Rank, Gunther; Berneder, Josef; Antrekowitsch, Helmut; Uggowitzer, Peter J.; Pogatscher, Stefan

2014-01-01

In this study, property criteria for automotive Al-Mg-Si sheet alloys are outlined and investigated in the context of commercial alloys AA6016, AA6005A, AA6063 and AA6013. The parameters crucial to predicting forming behavior were determined by tensile tests, bending tests, cross-die tests, hole-expansion tests and forming limit curve analysis in the pre-aged temper after various storage periods following sheet production. Roping tests were performed to evaluate surface quality, for the deployment of these alloys as an outer panel material. Strength in service was also tested after a simulated paint bake cycle of 20 min at 185 °C, and the corrosion behavior was analyzed. The study showed that forming behavior is strongly dependent on the type of alloy and that it is influenced by the storage period after sheet production. Alloy AA6016 achieves the highest surface quality, and pre-ageing of alloy AA6013 facilitates superior strength in service. Corrosion behavior is good in AA6005A, AA6063 and AA6016, and only AA6013 shows a strong susceptibility to intergranular corrosion. The results are discussed below with respect to the chemical composition, microstructure and texture of the Al-Mg-Si alloys studied, and decision-making criteria for appropriate automotive sheet alloys for specific applications are presented. PMID:28788119

An Innovative Parallel Test Sheet Composition Approach to Meet Multiple Assessment Criteria for National Tests

ERIC Educational Resources Information Center

Hwang, Gwo-Jen; Chu, Hui-Chun; Yin, Peng-Yeng; Lin, Ji-Yu

2008-01-01

The national certification tests and entrance examinations are the most important tests for proving the ability or knowledge level of a person. To accurately evaluate the professional skills or knowledge level, the composed test sheets must meet multiple assessment criteria such as the ratio of relevant concepts to be evaluated and the estimated…

[Tracing back for the basis. Research of Medieval medical manuscripts in Leipzig by Karl Sudhoff and Henry Ernest Sigerist].

PubMed

Löffler, Anette

2009-01-01

At the beginning of the 20th century, two known medical historians, Karl Sudhoff and Henry Ernst Sigerist, were among the first persons, who took up thorough investigations of medical manuscripts in Leipzig. Above all, it was Mr. Sudhoff, who developed his own procedure, in order to exploit the unknown stocks. Apart from the only means available to him, the so-called Leyser-papers, written by the Leipzig librarian Hermann Leyser, at least once Sudhoff made a complete check-up of all manuscripts over the period of 22 years. On 315 sheets he took down various more or less extensive notes regarding these Codices, which are kept today as manuscript collection (Ms 01269) in the library of the university of Leipzig. Many publications were written on the basis of these readings. Sigerist was only looking through a small number of Leipzig manuscripts, as could be seen from his remarks written onto the users' cards. However, he could rely on Sudhoff's notes and look for specific manuscripts that he was interested in and review them. This was a first and very important step for the investigation of Leipzig medical manuscripts.

Investigation on local ductility of 6xxx-aluminium sheet alloys

NASA Astrophysics Data System (ADS)

Henn, P.; Liewald, M.; Sindel, M.

2017-09-01

Within the scope of this paper influence of localization of loading conditions on the ductility of two different 6xxx-aluminium sheet alloys is investigated. In order to improve the prediction of sheet material crash performance, material parameters based on uniaxial tensile and notched tensile tests are determined with varying consolidation areas. Especially evaluation methods based on the localized necking behaviour in tensile tests are investigated. The potential of local ductility characterisation is validated with results of Edge-Compression Tests (ECT) which applies load conditions that occur in actual crash events.

Integrating personalized medical test contents with XML and XSL-FO.

PubMed

Toddenroth, Dennis; Dugas, Martin; Frankewitsch, Thomas

2011-03-01

In 2004 the adoption of a modular curriculum at the medical faculty in Muenster led to the introduction of centralized examinations based on multiple-choice questions (MCQs). We report on how organizational challenges of realizing faculty-wide personalized tests were addressed by implementation of a specialized software module to automatically generate test sheets from individual test registrations and MCQ contents. Key steps of the presented method for preparing personalized test sheets are (1) the compilation of relevant item contents and graphical media from a relational database with database queries, (2) the creation of Extensible Markup Language (XML) intermediates, and (3) the transformation into paginated documents. The software module by use of an open source print formatter consistently produced high-quality test sheets, while the blending of vectorized textual contents and pixel graphics resulted in efficient output file sizes. Concomitantly the module permitted an individual randomization of item sequences to prevent illicit collusion. The automatic generation of personalized MCQ test sheets is feasible using freely available open source software libraries, and can be efficiently deployed on a faculty-wide scale.

Development of a Cavitation Erosion Resistant Advanced Material System

DTIC Science & Technology

2005-11-01

Sheet EPD M results .............................................................................. 47 Figure 5.11 - EPDM rubber samples, sheet (left...Testing The long test times of EPDM rubber and other durable elastomer samples created a need for overnight testing capability. In the original test setup...seals, adhesives and molded flexible parts. Common examples of elastomers include natural and synthetic rubber , silicone, neoprene, EPDM , polyurethane

Recommended specifications and a tentative testing procedure for reflective sheeting.

DOT National Transportation Integrated Search

1977-01-01

The Department spends approximately a half million dollars annually on reflective sheeting for highway signs. For years this sheeting has been purchased primarily from one manufacturer, because of the inability of other firms to produce a competitive...

An effective self-assessment based on concept map extraction from test-sheet for personalized learning

NASA Astrophysics Data System (ADS)

Liew, Keng-Hou; Lin, Yu-Shih; Chang, Yi-Chun; Chu, Chih-Ping

2013-12-01

Examination is a traditional way to assess learners' learning status, progress and performance after a learning activity. Except the test grade, a test sheet hides some implicit information such as test concepts, their relationships, importance, and prerequisite. The implicit information can be extracted and constructed a concept map for considering (1) the test concepts covered in the same question means these test concepts have strong relationships, and (2) questions in the same test sheet means the test concepts are relative. Concept map has been successfully employed in many researches to help instructors and learners organize relationships among concepts. However, concept map construction depends on experts who need to take effort and time for the organization of the domain knowledge. In addition, the previous researches regarding to automatic concept map construction are limited to consider all learners of a class, which have not considered personalized learning. To cope with this problem, this paper proposes a new approach to automatically extract and construct concept map based on implicit information in a test sheet. Furthermore, the proposed approach also can help learner for self-assessment and self-diagnosis. Finally, an example is given to depict the effectiveness of proposed approach.

Explosive Testing of Class 1.3 Rocket Booster Propellant

DTIC Science & Technology

1994-08-01

molds were lined with 0.025 mm (0.001 in.) Velostat conductive plastic sheet and sprayed with a mold release that dried leaving fine Teflon powder... Velostat sheet (0.03 in.) was wrapped around the sample and grounded for improved electrostatic safety. Similar to previous cylinder tests, the...layer of thin Velostat plastic sheet, its contribution to camera viewing distortion of the flame front is not known. Overall, an average velocity over

Factors governing hole expansion ratio of steel sheets with smooth sheared edge

NASA Astrophysics Data System (ADS)

Yoon, Jae Ik; Jung, Jaimyun; Lee, Hak Hyeon; Kim, Gyo-Sung; Kim, Hyoung Seop

2016-11-01

Stretch-flangeability measured using hole expansion test (HET) represents the ability of a material to form into a complex shaped component. Despite its importance in automotive applications of advanced high strength steels, stretch-flangeability is a less known sheet metal forming property. In this paper, we investigate the factors governing hole expansion ratio (HER) by means of tensile test and HET. We correlate a wide range of tensile properties with HERs of steel sheet specimens because the stress state in the hole edge region during the HET is almost the same as that of the uniaxial tensile test. In order to evaluate an intrinsic HER of steel sheet specimens, the initial hole of the HET specimen is produced using a milling process after punching, which can remove accumulated shearing damage and micro-void in the hole edge region that is present when using the standard HER evaluation method. It was found that the intrinsic HER of steel sheet specimens was proportional to the strain rate sensitivity exponent and post uniform elongation.

A study of trends and techniques for space base electronics

NASA Technical Reports Server (NTRS)

Trotter, J. D.; Wade, T. E.; Gassaway, J. D.

1979-01-01

The use of dry processing and alternate dielectrics for processing wafers is reported. A two dimensional modeling program was written for the simulation of short channel MOSFETs with nonuniform substrate doping. A key simplifying assumption used is that the majority carriers can be represented by a sheet charge at the silicon dioxide-silicon interface. In solving current continuity equation, the program does not converge. However, solving the two dimensional Poisson equation for the potential distribution was achieved. The status of other 2D MOSFET simulation programs are summarized.

The Onset of the Cataclysm: In Situ Dating of the Nectaris Basin Impact Melt Sheet

NASA Technical Reports Server (NTRS)

Cohen, B. A.

2017-01-01

The impact history of the Moon has significant implications beyond simply excavating the surface of our nearest neighbor. The age distribution of lunar impact breccias inspired the idea of a catastrophic influx of asteroids and comets about 4 billion years ago and motivated new models of planetary dynamics. An epoch of heavy bombardment after planets had atmospheres and continents would have influenced the course of biologic evolution. The story of a cataclysmic bombardment, written in the rocks of the Moon, has far-reaching consequences.

Test Review: D. D. Hammill & S. C. Larsen "Test of Written Language-Fourth Edition." (TOWL-4). Austin, TX--PRO-ED, 2009

ERIC Educational Resources Information Center

McCrimmon, Adam W.; Climie, Emma A.

2011-01-01

This article presents a review of the "Test of Written Language-Fourth Edition" (TOWL-4), a newly updated individual or group-based measure of written language for students aged 9 years, 0 months through 17 years, 11 months. The stated purposes of the measure are to identify students in need of support or intervention in the area of…

Laser Indirect Shock Welding of Fine Wire to Metal Sheet

PubMed Central

Wang, Xiao; Huang, Tao; Luo, Yapeng; Liu, Huixia

2017-01-01

The purpose of this paper is to present an advanced method for welding fine wire to metal sheet, namely laser indirect shock welding (LISW). This process uses silica gel as driver sheet to accelerate the metal sheet toward the wire to obtain metallurgical bonding. A series of experiments were implemented to validate the welding ability of Al sheet/Cu wire and Al sheet/Ag wire. It was found that the use of a driver sheet can maintain high surface quality of the metal sheet. With the increase of laser pulse energy, the bonding area of the sheet/wire increased and the welding interfaces were nearly flat. Energy dispersive spectroscopy (EDS) results show that the intermetallic phases were absent and a short element diffusion layer which would limit the formation of the intermetallic phases emerging at the welding interface. A tensile shear test was used to measure the mechanical strength of the welding joints. The influence of laser pulse energy on the tensile failure modes was investigated, and two failure modes, including interfacial failure and failure through the wire, were observed. The nanoindentation test results indicate that as the distance to the welding interface decreased, the microhardness increased due to the plastic deformation becoming more violent. PMID:28895900

Written Informed-Consent Statutes and HIV Testing

PubMed Central

Ehrenkranz, Peter D.; Pagán, José A.; Begier, Elizabeth M.; Linas, Benjamin; Madison, Kristin; Armstrong, Katrina

2009-01-01

Background Almost 1 million Americans are infected with HIV, yet it is estimated that as many as 250,000 of them do not know their serostatus. This study examined whether people residing in states with statutes requiring written informed consent prior to HIV testing were less likely to report a recent HIV test. Methods The study is based on survey data from the 2004 Behavioral Risk Factor Surveillance System. Logistic regression was used to assess the association between residence in a state with a pre-test written informed-consent requirement and individual self-report of recent HIV testing. The regression analyses controlled for potential state- and individual-level confounders. Results Almost 17% of respondents reported that they had been tested for HIV in the prior 12 months. Ten states had statutes requiring written informed consent prior to routine HIV testing; nine of those were analyzed in this study. After adjusting for other state- and individual-level factors, people who resided in these nine states were less likely to report a recent history of HIV testing (OR=0.85; 95% CI=0.80, 0.90). The average marginal effect was −0.02 (p<0.001, 95%CI= −0.03, −0.01); thus, written informed-consent statutes are associated with a 12% reduction in HIV testing from the baseline testing level of 17%. The association between a consent requirement and lack of testing was greatest among respondents who denied HIV risk factors, were non-Hispanic whites, or who had higher levels of education. Conclusions This study’s findings suggest that the removal of written informed-consent requirements might promote the non–risk-based routine-testing approach that the CDC advocates in its new testing guidelines. PMID:19423271

An investigation into pilot and system response to critical in-flight events, volume 2

NASA Technical Reports Server (NTRS)

Rockwell, T. H.; Giffin, W. C.

1981-01-01

Critical in-flight event is studied using mission simulation and written tests of pilot responses. Materials and procedures used in knowledge tests, written tests, and mission simulations are included

A Particle Swarm Optimization Approach to Composing Serial Test Sheets for Multiple Assessment Criteria

ERIC Educational Resources Information Center

Yin, Peng-Yeng; Chang, Kuang-Cheng; Hwang, Gwo-Jen; Hwang, Gwo-Haur; Chan, Ying

2006-01-01

To accurately analyze the problems of students in learning, the composed test sheets must meet multiple assessment criteria, such as the ratio of relevant concepts to be evaluated, the average discrimination degree, difficulty degree and estimated testing time. Furthermore, to precisely evaluate the improvement of student's learning performance…

Gender, mathematics, reading comprehension and science reasoning as predictors of science achievement among African-American students at a historical black college or university

NASA Astrophysics Data System (ADS)

Davis, Consuella Artiemese

This study investigated predictors that influence the science achievement of African-American non-science majors in a Physical Science class. The population consisted of male and female college students enrolled in Physical Science courses at a historical black college or university (HBCU) located in the southeastern portion of the United States. A personal data information sheet was administered to 120 participants during the Fall of 2008. The personal data information sheet consisted of questions pertaining to the high school courses, students took in math, language arts and science. It also consisted of basic background information. Students also gave written consent for their midterm and final grades earned in Physical Science to be used in the study as part of the analyses. A t-Test including chi-square tests revealed that there was not a significant difference in the raw scores of African-American females and African American males on the American College Test. A significant difference was not observed between the females and males on the ACT math subtest, t (118) = -.78, p = .43; reading comprehension subtest, t (118) = -1.44, .15 or on the science reasoning subtest, t (118) = -1.46, p = .15. A significant difference was not found between the final grades of African American females and the final grades of African American males. Chi-square tests were conducted to determine goodness of fit, X2 = 6.11, df = 1, p = .191. Although the grades of females were higher than males, results were not significant. The correlation between math ACT and final grades were not significant, r = .131, N = 120, p = .155, reading comprehension ACT and final grades were not significant, r = .072, N = 120, p = .434 and science reasoning ACT and final grades were found not to be significant, r = .109, N = 120, p = .237. Being that the majority of students who participated in the study were from one state, had similar high school backgrounds, had similar majors and were similar in age the sample had more homogeneity than difference. This may be the most plausible explanation for the results found in this study.

Welding.

ERIC Educational Resources Information Center

Cowan, Earl; And Others

The curriculum guide for welding instruction contains 16 units presented in six sections. Each unit is divided into the following areas, each of which is color coded: terminal objectives, specific objectives, suggested activities, and instructional materials; information sheet; transparency masters; assignment sheet; test; and test answers. The…

List of Research Publications 1940-1980

DTIC Science & Technology

1981-10-01

comparison of the amount of tolerance for misplaced answers found in the GPO and the IBM machine-scored answer sheets. January 1942. (X6304) 1-18 A& .1...machine scoring of answer sheets. March 1942. The effect of the use of No. I pencils on the accuracy of scoring IBM answer sheets by machine. July 1942...X6427) 482 Hobbies - IBM code. 483 Relationship of Classification Test, R-I and WAC Classi- 4023 fication Test-2 for a recruiting station population

Sensitivity of simulated englacial isochrones to uncertain subglacial boundary conditions in central West Antarctica: Implications for detecting changes in ice dynamics

NASA Astrophysics Data System (ADS)

Muldoon, Gail; Jackson, Charles S.; Young, Duncan A.; Quartini, Enrica; Cavitte, Marie G. P.; Blankenship, Donald D.

2017-04-01

Information about the extent and dynamics of the West Antarctic Ice Sheet during past glaciations is preserved inside ice sheets themselves. Ice cores are capable of retrieving information about glacial history, but they are spatially sparse. Ice-penetrating radar, on the other hand, has been used to map large areas of the West Antarctic Ice Sheet and can be correlated to ice core chronologies. Englacial isochronous layers observed in ice-penetrating radar are the result of variations in ice composition, fabric, temperature and other factors. The shape of these isochronous surfaces is expected to encode information about past and present boundary conditions and ice dynamics. Dipping of englacial layers, for example, may reveal the presence of rapid ice flow through paleo ice streams or high geothermal heat flux. These layers therefore present a useful testbed for hypotheses about paleo ice sheet conditions. However, hypothesis testing requires careful consideration of the sensitivity of layer shape to the competing forces of ice sheet boundary conditions and ice dynamics over time. Controlled sensitivity tests are best completed using models, however ice sheet models generally do not have the capability of simulating layers in the presence of realistic boundary conditions. As such, modeling 3D englacial layers for comparison to observations is difficult and requires determination of a 3D ice velocity field. We present a method of post-processing simulated 3D ice sheet velocities into englacial isochronous layers using an advection scheme. We then test the sensitivity of layer geometry to uncertain boundary conditions, including heterogeneous subglacial geothermal flux and bedrock topography. By identifying areas of the ice sheet strongly influenced by boundary conditions, it may be possible to isolate the signature of paleo ice dynamics in the West Antarctic ice sheet.

Electrical Subsystems Flight Test Handbook

DTIC Science & Technology

1984-01-01

distribution of this handbook to the public at large, or by DDC to the National Technical Information Service (NTIS). At NTIS, it will be available to...Abnormal Mode 58 Emergency Mode 61 Instrumentation 62 Test Information Sheets 62 Integration with Flight Test Program 62 DATA MEASUREMENT, ANALYS IS...AND EVALUATION 65 REFERENCES 73 -APPENDIX A - EXAMPLE OF TEST INFORMATION SHEET 75 APPENDIX B - EXAMPLE OF TEST PLAN SAFETY REVIEW 85 APPENDIX C

Controlling microstructure and texture in magnesium alloy sheet by shear-based deformation processing

NASA Astrophysics Data System (ADS)

Sagapuram, Dinakar

Application of lightweight Mg sheet is limited by its low workability, both in production of sheet (typically by multistep hot and cold-rolling) and forming of sheet into components. Large strain extrusion machining (LSEM), a constrained chip formation process, is used to create Mg alloy AZ31B sheet in a single deformation step. The deformation in LSEM is shown to be intense simple shear that is confined to a narrow zone, which results in significant deformation-induced heating up to ~ 200°C and reduces the need for pre-heating to realize continuous sheet forms. This study focuses on the texture and microstructure development in the sheet processed by LSEM. Interestingly, deep, highly twinned steady-state layer develops in the workpiece subsurface due to the compressive field ahead of the shear zone. The shear deformation, in conjunction with this pre-deformed twinned layer, results in tilted-basal textures in the sheet with basal planes tilted well away from the surface. These textures are significantly different from those in rolled sheet, where basal planes are nearly parallel to the surface. By controlling the strain path, the basal plane inclination from the surface could be varied in the range of 32-53°. B-fiber (basal plane parallel to LSEM shear plane), associated with basal slip, is the major texture component in the sheet. An additional minor C2-fiber component appears above 250°C due to the thermal activation of pyramidal slip. Together with these textures, microstructure ranges from severely cold-worked to (dynamically) recrystallized type, with the corresponding grain sizes varying from ultrafine- (~ 200 nm) to fine- (2 mum) grained. Small-scale limiting dome height (LDH) confirmed enhanced formability (~ 50% increase in LDH) of LSEM sheet over the conventional rolled sheet. Premature, twinning-driven shear fractures are observed in the rolled sheet with the basal texture. In contrast, LSEM sheet with a tilted-basal texture favorably oriented for basal slip exhibits ductile tensile-type fracture. A two-fold increase in ductility is also observed for the LSEM sheet under uniaxial tensile testing without significant changes in the strength. Among texture and microstructure (grain size), texture is shown to be more critical for Mg sheet formability. However, in conjunction with a favorable texture, fine recrystallized microstructure provides for additional enhancement of strain-hardening capacity and formability. In-situ imaging of material flow during uniaxial tensile testing revealed new, interesting flow localization phenomena and fracture behavior. It is shown that the deformation behavior of Mg sheet is highly texture dependent, and also radically different from that of conventional ductile metals both in terms of necking and fracture. The implications of these observations for the LDH test results and formability of Mg sheet, in general, are briefly discussed.

Test Anxiety in Written and Oral Examinations

ERIC Educational Resources Information Center

Sparfeldt, Jorn R.; Rost, Detlef H.; Baumeister, Ulrike M.; Christ, Oliver

2013-01-01

The distinction of different test anxiety reactions (e.g., worry, emotionality) is well established. Recently, additional relevance has been given to school-subject-specific test anxiety factors. The present study explored a further aspect concerning the structure of test anxiety experiences, specifically oral versus written examination modes. A…

[Knowledge on Loose Sheets in the Context of fixed Theories. Theodor Leber's Research of Inflammation].

PubMed

Stahl, Dorina

2016-09-01

At the end of the nineteenth century, after twelve years of intensive research, the ophthalmologist Theodor Leber (1840-1917) established the chemotaxis of leukocytes as part of inflammation research. Although at the time his theory was smoothly enlisted into immunological research, up until now his name has been connected to chemotaxis only in the English-language literature. Leber was able to use his experimental system to develop a theory of the chemical attraction of the leukocytes during inflammation processes by the beginning of the 1880s, but his unconventional methodology-introducing chemically neutral contaminants in order to trigger inflammation in the eyes of rabbits-contradicted the basic bacteriological Denkstil (style of thought) of inflammation research at the time. Leber held fast to his research practice, which consisted of closely interlocking experimental and theoretical work. Only when an opening appeared in the bacteriological Denkstil was Leber able to transform his experimental observations, written on loose sheets of paper, into convincing evidence for his theory of inflammation. This micro-historical reconstruction of Leber's experimental and written work, based on his original lab protocols, opens up the research practice of a scientist who was not recognized by the established microbiological inflammation research of the time. Moreover, persistent factors in the generation of knowledge are revealed by connecting this micro-historical reconstruction with a macro-history analysis. Indeed Leber developed his specific paper technology in order to mobilise and stabilise the scientific findings gained through experiment because of the persistence of the bacteriological Denkstil.

A new full-Stokes model as a tool for basal inversions.

NASA Astrophysics Data System (ADS)

Kyrke-Smith, Teresa M.; Hilmar Gudmundsson, G.; Farrell, Patrick E.

2016-04-01

High resolution models of ice sheet dynamics are required to make accurate predictions of the future mass balance of ice sheets. These require knowledge of flow conditions at the bed of the ice, however, the inaccessibility of the bed means there exist few observational constraints. Inverse methods are therefore commonly used to obtain information about the nature of basal control using given surface observations. We present a new 3D Stokes solver written using FEniCS with the potential to carry out second-order inversions for basal slipperiness. We will be applying the model to Pine Island Glacier, Antarctica. Pine Island Glacier is one of the fastest flowing and most rapidly changing ice streams in Antarctica, and is currently contributing to sea-level rise at an increasing rate. Recent field seasons as part of the iSTAR project have acquired high-resolution in-situ geophysical measurements; results from our model will be compared with these to try and increase understanding about the conditions at the bed of Pine Island Glacier.

Experiments on terahertz 3D scanning microscopic imaging

NASA Astrophysics Data System (ADS)

Zhou, Yi; Li, Qi

2016-10-01

Compared with the visible light and infrared, terahertz (THz) radiation can penetrate nonpolar and nonmetallic materials. There are many studies on the THz coaxial transmission confocal microscopy currently. But few researches on the THz dual-axis reflective confocal microscopy were reported. In this paper, we utilized a dual-axis reflective confocal scanning microscope working at 2.52 THz. In contrast with the THz coaxial transmission confocal microscope, the microscope adopted in this paper can attain higher axial resolution at the expense of reduced lateral resolution, revealing more satisfying 3D imaging capability. Objects such as Chinese characters "Zhong-Hua" written in paper with a pencil and a combined sheet metal which has three layers were scanned. The experimental results indicate that the system can extract two Chinese characters "Zhong," "Hua" or three layers of the combined sheet metal. It can be predicted that the microscope can be applied to biology, medicine and other fields in the future due to its favorable 3D imaging capability.

Rotator cuff repair using cell sheets derived from human rotator cuff in a rat model.

PubMed

Harada, Yoshifumi; Mifune, Yutaka; Inui, Atsuyuki; Sakata, Ryosuke; Muto, Tomoyuki; Takase, Fumiaki; Ueda, Yasuhiro; Kataoka, Takeshi; Kokubu, Takeshi; Kuroda, Ryosuke; Kurosaka, Masahiro

2017-02-01

To achieve biological regeneration of tendon-bone junctions, cell sheets of human rotator-cuff derived cells were used in a rat rotator cuff injury model. Human rotator-cuff derived cells were isolated, and cell sheets were made using temperature-responsive culture plates. Infraspinatus tendons in immunodeficient rats were resected bilaterally at the enthesis. In right shoulders, infraspinatus tendons were repaired by the transosseous method and covered with the cell sheet (sheet group), whereas the left infraspinatus tendons were repaired in the same way without the cell sheet (control group). Histological examinations (safranin-O and fast green staining, isolectin B4, type II collagen, and human-specific CD31) and mRNA expression (vascular endothelial growth factor; VEGF, type II collagen; Col2, and tenomodulin; TeM) were analyzed 4 weeks after surgery. Biomechanical tests were performed at 8 weeks. In the sheet group, proteoglycan at the enthesis with more type II collagen and isolectin B4 positive cells were seen compared with in the control group. Human specific CD31-positive cells were detected only in the sheet group. VEGF and Col2 gene expressions were higher and TeM gene expression was lower in the sheet group than in the control group. In mechanical testing, the sheet group showed a significantly higher ultimate failure load than the control group at 8 weeks. Our results indicated that the rotator-cuff derived cell sheet could promote cartilage regeneration and angiogenesis at the enthesis, with superior mechanical strength compared with the control. Treatment for rotator cuff injury using cell sheets could be a promising strategy for enthesis of tendon tissue engineering. © 2016 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 35:289-296, 2017. © 2016 Orthopaedic Research Society. Published by Wiley Periodicals, Inc.

Practical Business: Instructor/Student Guide.

ERIC Educational Resources Information Center

Napier, Deedee Stocker

Ten units on practical business are presented in this instructor and student guide. Each instructional unit contains objectives, suggested activities, information sheets, assignment sheets, transparency master, a test, and test answers. Unit topics are (1) before you buy (comparative shopping and wise purchasing techniques); (2) when things go…

Experimental and Numerical Study on the Deformation Mechanism in AZ31B Mg Alloy Sheets Under Pulsed Electric-Assisted Tensile and Compressive Tests

NASA Astrophysics Data System (ADS)

Lee, Jinwoo; Kim, Se-Jong; Lee, Myoung-Gyu; Song, Jung Han; Choi, Seogou; Han, Heung Nam; Kim, Daeyong

2016-06-01

The uniaxial tensile and compressive stress-strain responses of AZ31B magnesium alloy sheet under pulsed electric current are reported. Tension and compression tests with pulsed electric current showed that flow stresses dropped instantaneously when the electric pulses were applied. Thermo-mechanical-electrical finite element analyses were also performed to investigate the effects of Joule heating and electro-plasticity on the flow responses of AZ31B sheets under electric-pulsed tension and compression tests. The proposed finite element simulations could reproduce the measured uniaxial tensile and compressive stress-strain curves under pulsed electric currents, when the temperature-dependent flow stress hardening model and thermal properties of AZ31B sheet were properly described in the simulations. In particular, the simulation results that fit best with experimental results showed that almost 100 pct of the electric current was subject to transform into Joule heating during electrically assisted tensile and compressive tests.

Test anxiety and academic performance in chiropractic students.

PubMed

Zhang, Niu; Henderson, Charles N R

2014-01-01

Objective : We assessed the level of students' test anxiety, and the relationship between test anxiety and academic performance. Methods : We recruited 166 third-quarter students. The Test Anxiety Inventory (TAI) was administered to all participants. Total scores from written examinations and objective structured clinical examinations (OSCEs) were used as response variables. Results : Multiple regression analysis shows that there was a modest, but statistically significant negative correlation between TAI scores and written exam scores, but not OSCE scores. Worry and emotionality were the best predictive models for written exam scores. Mean total anxiety and emotionality scores for females were significantly higher than those for males, but not worry scores. Conclusion : Moderate-to-high test anxiety was observed in 85% of the chiropractic students examined. However, total test anxiety, as measured by the TAI score, was a very weak predictive model for written exam performance. Multiple regression analysis demonstrated that replacing total anxiety (TAI) with worry and emotionality (TAI subscales) produces a much more effective predictive model of written exam performance. Sex, age, highest current academic degree, and ethnicity contributed little additional predictive power in either regression model. Moreover, TAI scores were not found to be statistically significant predictors of physical exam skill performance, as measured by OSCEs.

Life without Scan-Tron: Tests as Thinking.

ERIC Educational Resources Information Center

Posner, Richard

1987-01-01

Claims that written tests are superior to objective, scan-tron tests in literature, composition, and vocabulary because they require students to think on paper. Describes the following types of in-class written tests and examines the advantages of each: literary essay, topical composition, imitation, brief answer, timed rewrites, and vocabulary…

Paternity analysis in Excel.

PubMed

Rocheta, Margarida; Dionísio, F Miguel; Fonseca, Luís; Pires, Ana M

2007-12-01

Paternity analysis using microsatellite information is a well-studied subject. These markers are ideal for parentage studies and fingerprinting, due to their high-discrimination power. This type of data is used to assign paternity, to compute the average selfing and outcrossing rates and to estimate the biparental inbreeding. There are several public domain programs that compute all this information from data. Most of the time, it is necessary to export data to some sort of format, feed it to the program and import the output to an Excel book for further processing. In this article we briefly describe a program referred from now on as Paternity Analysis in Excel (PAE), developed at IST and IBET (see the acknowledgments) that computes paternity candidates from data, and other information, from within Excel. In practice this means that the end user provides the data in an Excel sheet and, by pressing an appropriate button, obtains the results in another Excel sheet. For convenience PAE is divided into two modules. The first one is a filtering module that selects data from the sequencer and reorganizes it in a format appropriate to process paternity analysis, assuming certain conventions for the names of parents and offspring from the sequencer. The second module carries out the paternity analysis assuming that one parent is known. Both modules are written in Excel-VBA and can be obtained at the address (www.math.ist.utl.pt/~fmd/pa/pa.zip). They are free for non-commercial purposes and have been tested with different data and against different software (Cervus, FaMoz, and MLTR).

Solar Heating Systems: Student Manual.

ERIC Educational Resources Information Center

Green, Joanne; And Others

This Student Manual for a Solar Heating System curriculum contains 22 units of instructional materials for students to use in a course or courses on solar heating systems (see note). For each unit (task), objectives, assignment sheets, laboratory assignments, information sheets, checkpoints (tests), and job sheets are provided. Materials are set…

40 CFR 60.52Da - Recordkeeping requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

... (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Standards of Performance for Electric Utility... opacity field data sheets; (2) For each performance test conducted using Method 22 of appendix A-4 of this... performance test; (iii) Copies of all visible emission observer opacity field data sheets; and (iv...

Real-time testing of titanium sheet and extrusion coupon specimens subjected to Mach 2.7 supersonic cruise aircraft wing stresses and temperatures

NASA Technical Reports Server (NTRS)

Lunde, T.

1977-01-01

The accuracy of three accelerated flight-by-flight test methods for material selection, and fatigue substantiation of supersonic cruise aircraft structure was studied. The real time stresses and temperatures applied to the specimens were representative of the service conditions in the lower surface of a Mach 2.7 supersonic cruise aircraft wing root structure. Each real time flight lasted about 65 minutes, including about one hour at (500 F) in the cruise condition. Center notched coupon specimens from six titanium materials were tested: mill-annealed, duplex-annealed, and triplex-annealed Ti-8Al-1Mo-1V sheets; mill-annealed Ti-8Al-1Mo-1V extrusion; mill-annealed Ti-6Al-4V sheet; and solution-treated and aged Ti-6Al-4V extrusion. For duplex-annealed Ti-8Al-1Mo-1V sheet, specimens with single spotweld were also tested. The test results were studied in conjunction with other related data from the literature for: material selection, structural fabrication, fatigue resistance of supersonic cruise aircraft structure, and fatigue test acceleration procedures for supersonic cruise aircraft.

Peeling behavior and spalling resistance of CFRP sheets bonded to bent concrete surfaces

NASA Astrophysics Data System (ADS)

Yuan, Hong; Li, Faping

2010-05-01

In this paper, the peeling behavior and the spalling resistance effect of carbon fiber reinforced polymer (CFRP) sheets externally bonded to bent concrete surfaces are firstly investigated experimentally. Twenty one curved specimens and seven plane specimens are studied in the paper, in which curved specimens with bonded CFRP sheets can simulate the concrete spalling in tunnel, culvert, arch bridge etc., whereas plane specimens with bonded CFRP sheets can simulate the concrete spalling in beam bridge, slab bridge and pedestrian bridge. Three kinds of curved specimens with different radii of curvature are chosen by referring to practical tunnel structures, and plane specimens are used for comparison with curved ones. A peeling load is applied on the FRP sheet by loading a circular steel tube placed into the central notch of beam to debond CFRP sheets from the bent concrete surface, meanwhile full-range load-deflection curves are recorded by a MTS 831.10 Elastomer Test System. Based on the experimental results, a theoretical analysis is also conducted for the specimens. Both theoretical and experimental results show that only two material parameters, the interfacial fracture energy of CFRP-concrete interface and the tensile stiffness of CFRP sheets, are needed for describing the interfacial spalling behavior. It is found that the radius of curvature has remarkable influence on peeling load-deflection curves. The test methods and test results given in the paper are helpful and available for reference to the designer of tunnel strengthening.

10 CFR 55.43 - Written examination: Senior operators.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 2 2010-01-01 2010-01-01 false Written examination: Senior operators. 55.43 Section 55.43... Tests § 55.43 Written examination: Senior operators. (a) Content. The written examination for a senior... needed to perform licensed senior operator duties. The knowledge, skills, and abilities will be...

[Writing and publication of a clinical case report].

PubMed

Târcoveanu, E; Roca, M; Mihăescu, T

2011-01-01

A case report represents a collection of detailed information about an individual patient, written with the purpose to disseminate clinical outcomes, not previously reported. Case reports provide a rich resource for teaching and research in medicine. Despite the limitation of case reports, these are useful to generate new hypothesis for future large scale clinical trials. A clinical case report should be well structured and convey a clear message. Elements of a case report are similar to all forms of medical scientific articles: title, structured abstract, introduction, case report, discussion, conclusion and references. A well written case report with literature support and a detailed description of management of the case has the greatest chances to be published. "Uniform Requirements for Manuscripts to Biomedical Journals" form the basis for most journal instructions regarding content and formatting and should be consulted when journal's instructions don't answer to author's questions. In this paper we present a case report check sheet to use as a form of self-evaluation, prior to submitting the articles.

A Process for Reviewing and Evaluating Generated Test Items

ERIC Educational Resources Information Center

Gierl, Mark J.; Lai, Hollis

2016-01-01

Testing organization needs large numbers of high-quality items due to the proliferation of alternative test administration methods and modern test designs. But the current demand for items far exceeds the supply. Test items, as they are currently written, evoke a process that is both time-consuming and expensive because each item is written,…

Test Review: Schrank, F. A., Mather, N., & McGrew, K. S. (2014). Woodcock-Johnson IV Tests of Achievement

ERIC Educational Resources Information Center

Villarreal, Victor

2015-01-01

The Woodcock-Johnson IV Tests of Achievement (WJ IV ACH; Schrank, Mather, & McGrew, 2014a) is an individually administered measure containing tests of reading, mathematics, written language, and academic knowledge. Areas of reading, mathematics, and written language each include tests of basic skills, fluency, and application. Academic…

Readability of the Written Study Information in Pediatric Research in France

PubMed Central

Ménoni, Véronique; Lucas, Noël; Leforestier, Jean-François; Doz, François; Chatellier, Gilles; Jacqz-Aigain, Evelyne; Giraud, Carole; Tréluyer, Jean-Marc; Chappuy, Hélène

2011-01-01

Background The aim was to evaluate the readability of research information leaflets (RIL) for minors asked to participate in biomedical research studies and to assess the factors influencing this readability. Methods and Findings All the pediatric protocols from three French pediatric clinical research units were included (N = 104). Three criteria were used to evaluate readability: length of the text, Flesch's readability score and presence of illustrations. We compared the readability of RIL to texts specifically written for children (school textbooks, school exams or extracts from literary works). We assessed the effect of protocol characteristics on readability. The RIL had a median length of 608 words [350 words, 25th percentile; 1005 words, 75th percentile], corresponding to two pages. The readability of the RIL, with a median Flesch score of 40 [30; 47], was much poorer than that of pediatric reference texts, with a Flesch score of 67 [60; 73]. A small proportion of RIL (13/91; 14%) were illustrated. The RIL were longer (p<0.001), more readable (p<0.001) and more likely to be illustrated (p<0.009) for industrial than for institutional sponsors. Conclusion Researchers should routinely compute the reading ease of study information sheets and make greater efforts to improve the readability of written documents for potential participants. PMID:21494689

Analysis of fracture in sheet bending and roll forming

NASA Astrophysics Data System (ADS)

Deole, Aditya D.; Barnett, Matthew; Weiss, Matthias

2018-05-01

The bending limit or minimum bending radius of sheet metal is conventionally measured in a wiping (swing arm) or in a vee bend test and reported as the minimum radius of the tool over which the sheet can be bent without fracture. Frequently the material kinks while bending so that the actual inner bend radius of the sheet metal is smaller than the tool radius giving rise to inaccuracy in these methods. It has been shown in the previous studies that conventional bend test methods may under-estimate formability in bending dominated processes such as roll forming. A new test procedure is proposed here to improve understanding and measurement of fracture in bending and roll forming. In this study, conventional wiping test and vee bend test have been performed on martensitic steel to determine the minimum bend radius. In addition, the vee bend test is performed in an Erichsen sheet metal tester equipped with the GOM Aramis system to enable strain measurement on the outer surface during bending. The strain measurement before the onset of fracture is then used to determine the minimum bend radius. To compare this result with a technological process, a vee channel is roll formed and in-situ strain measurement carried out with the Vialux Autogrid system. The strain distribution at fracture in the roll forming process is compared with that predicted by the conventional bending tests and by the improved process. It is shown that for this forming operation and material, the improved procedure gives a more accurate prediction of fracture.

75 FR 43995 - Agency Information Collection Activities: Submission for OMB Review; Comment Request, OMB No...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-07-27

... DEPARTMENT OF HOMELAND SECURITY Federal Emergency Management Agency [Docket ID: FEMA-2010-0026...; FEMA/EMI Independent Study Course Enrollment and Test Answer Sheet AGENCY: Federal Emergency Management... Course Enrollment and Test Answer Sheet (paper and electronic). SUMMARY: The Federal Emergency Management...

Comparison of Written and Oral Examinations in a Baccalaureate Medical-Surgical Nursing Course.

ERIC Educational Resources Information Center

Rushton, Patricia; Eggett, Dennis

2003-01-01

Of four groups of medical-surgical nurses, 55 took one final and three midterm written exams, 150 took one each (written), 45 took an oral final, 92 took both written and oral, and 47 took a written test with licensure questions and an oral final. Oral exams resulted in higher scores, more effective study habits, and increased application. (SK)

Influence of Accumulative Roll Bonding on the Texture and Tensile Properties of an AZ31 Magnesium Alloy Sheets

PubMed Central

Džugan, Ján; Németh, Gergely; Lukáč, Pavel; Bohlen, Jan

2018-01-01

Deformation behaviour of rolled AZ31 sheets that were subjected to the accumulative roll bonding was investigated. Substantially refined microstructure of samples was achieved after the first and second pass through the rolling mill. Sheets texture was investigated using an X-ray diffractometer. Samples for tensile tests were cut either parallel or perpendicular to the rolling direction. Tensile tests were performed at temperatures ranging from room temperature up to 300 °C. Tensile plastic anisotropy, different from the anisotropy observed in AZ31 sheets by other authors, was observed. This anisotropy decreases with an increasing number of rolling passes and increasing deformation temperature. Grain refinement and texture are the crucial factors influencing the deformation behaviour. PMID:29303975

Flight Engineer. Question Book. Expires September 1, 1991.

ERIC Educational Resources Information Center

Federal Aviation Administration (DOT), Washington, DC.

This question book was developed by the Federal Aviation Administration (FAA) to be used by FAA testing centers and FAA-designated written test examiners when administering the flight engineer written test. The book can be used to test applicants in the following flight engineer knowledge areas: basic, turbojet powered, turbopropeller powered, and…

Lightweight long life heat exchanger

NASA Technical Reports Server (NTRS)

Moore, E. K.

1975-01-01

The design, fabrication, and evaluation of a full scale shuttle-type condensing heat exchanger constructed of aluminum and utilizing aluminum clad titanium parting sheets is described. A long term salt spray test of candidate parting sheet specimens is described. The results of an investigation into an alternate method of making composite sheet material are discussed.

Tests for Z-direction fiber orientation

Treesearch

David W. Vahey; John M. Considine

2007-01-01

Fibers that acquire a Z-direction tilt in the forming process help bond adjacent strata of the paper sheet, increasing Z-direction shear and other properties. For certain tests, this manifests itself as a test difference upon 180° in-plane rotation of the sheet. Seven of eight different paper grades ranging in grammage from 73 to 268 g/m2 were found to show this...

Photographic copy of plan of new Dy horizontal station and ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Photographic copy of plan of new Dy horizontal station and accumulator additions to Test Stand "D," also showing existing Dd test station. JPL drawing by VTN Consolidated, Inc. Engineers, Architects, Planners, 2301 Campus Drive, Irvine, California 92664: "Jet Propulsion Laboratory-Edwards Test Station, Motive Steam Supply & Ejector Pumping System: Plan - Test Stand "D," sheet M-3 (JPL sheet number E24/33), 21 December 1976 - Jet Propulsion Laboratory Edwards Facility, Test Stand D, Edwards Air Force Base, Boron, Kern County, CA

Computer printing and filing of microbiology reports. 1. Description of the system.

PubMed Central

Goodwin, C S; Smith, B C

1976-01-01

From March 1974 all reports from this microbiology department have been computer printed and filed. The system was designed to include every medically important microorganism and test. Technicians at the laboratory bench made their results computer-readable using Port-a-punch cards, and specimen details were recorded on paper-tape, allowing the full description of each specimen to appear on the report. A summary form of each microbiology phrase enabled copies of reports to be printed on wide paper with 12 to 18 reports per sheet; such copies, in alphabetical order for one day, and cumulatively for one week were used by staff answering enquiries to the office. This format could also be used for printing allthe reports for one patient. Retrieval of results from the files was easily performed and was useful to medical and laboratory staff and for control-of-infection purposes. The system was written in COBOL and was designed to be as cost-effective as possible without sacrificing accuracy; the cost of a report and its filing was 17-97 pence. Images PMID:939809

Hypotetical learning trajectory to anticipate mathematics anxiety in algebra learning based on the perspective of didactical situation theory

NASA Astrophysics Data System (ADS)

Yuliani, R. E.; Suryadi, D.; Dahlan, J. A.

2018-05-01

The objective of this research is to design an alleged teacher learning path or Hypotetical Learning Trajectory (HLT) to anticipate mathematics anxiety of students in learning algebra. HLT loads expected mathematics learning objectives, estimates the level of knowledge and understanding of the students, as well as the selection of mathematical activity in accordance with the learning competencies. This research uses educational design research method. The research steps consist of a preliminary design, experimental and retrospective analysis. Data were gathered from various sources, such as data is written during the research process of test results, documentation, sheet results of students' work, results of interviews, questionnaires, and video recordings. The subjects of the study were 10 junior high school students. Based on the research identified 2 students at the level of high anxiety, 7 people at medium anxiety level and 1 student at low anxiety level. High anxiety levels about 20%, was approximately 70% and approximately 10% lower. These results can be used as an evaluation and reflection for designing materials that can anticipate mathematics anxiety of students learning algebra concepts.

Impact verification of space suit design for space station

NASA Technical Reports Server (NTRS)

Fish, Richard H.

1987-01-01

The ballistic limits of single sheet and double sheet structures made of 6061 T6 Aluminum of 1.8 mm and larger nominal thickness were investigated for projectiles of 1.5 mm diameter fired in the Vertical Gun Range Test Facility and NASA Ames Research Center. The hole diameters and sheet deformation behavior were studied for various ratios of sheet spacing to projectile diameter. The results indicate that for projectiles of less than 1.5 mm diameter the ballistic limit exceeds the nominal 10 km/sec orbital debris encounter velocity, if a single-sheet suit of 1.8 mm thickness is behind a single bumper sheet of 1 mm thickness spaced 12.5 mm apart.

Characterization of the mechanical and physical properties of TD-NiCr (Ni-20Cr-2ThO2) alloy sheet

NASA Technical Reports Server (NTRS)

Fritz, L. J.; Koster, W. P.; Taylor, R. E.

1973-01-01

Sheets of TD-NiCr processed using techniques developed to produce uniform material were tested to supply mechanical and physical property data. Two heats each of 0.025 and 0.051 cm thick sheet were tested. Mechanical properties evaluated included tensile, modulus of elasticity, Poisson's Ratio, compression, creep-rupture, creep strength, bearing strength, shear strength, sharp notch and fatigue strength. Test temperatures covered the range from ambient to 1589K. Physical properties were also studied as a function of temperature. The physical properties measured were thermal conductivity, linear thermal expansion, specific heat, total hemispherical emittance, thermal diffusivity, and electrical conductivity.

Effects of die quench forming on sheet thinning and 3-point bend testing of AA7075-T6

NASA Astrophysics Data System (ADS)

Kim, Samuel; Omer, Kaab; Rahmaan, Taamjeed; Butcher, Clifford; Worswick, Michael

2017-10-01

Lab-scaled AA7075 aluminum side impact beams were manufactured using the die quenching technique in which the sheet was solutionized and then quenched in-die during forming to a super saturated solid state. Sheet thinning measurements were taken at various locations throughout the length of the part and the effect of lubricant on surface scoring and material pick-up on the die was evaluated. The as-formed beams were subjected to a T6 aging treatment and then tested in three-point bending. Simulations were performed of the forming and mechanical testing experiments using the LS-DYNA finite element code. The thinning and mechanical response was predicted well.

LIVVkit: An extensible, python-based, land ice verification and validation toolkit for ice sheet models

NASA Astrophysics Data System (ADS)

Kennedy, Joseph H.; Bennett, Andrew R.; Evans, Katherine J.; Price, Stephen; Hoffman, Matthew; Lipscomb, William H.; Fyke, Jeremy; Vargo, Lauren; Boghozian, Adrianna; Norman, Matthew; Worley, Patrick H.

2017-06-01

To address the pressing need to better understand the behavior and complex interaction of ice sheets within the global Earth system, significant development of continental-scale, dynamical ice sheet models is underway. Concurrent to the development of the Community Ice Sheet Model (CISM), the corresponding verification and validation (V&V) process is being coordinated through a new, robust, Python-based extensible software package, the Land Ice Verification and Validation toolkit (LIVVkit). Incorporated into the typical ice sheet model development cycle, it provides robust and automated numerical verification, software verification, performance validation, and physical validation analyses on a variety of platforms, from personal laptops to the largest supercomputers. LIVVkit operates on sets of regression test and reference data sets, and provides comparisons for a suite of community prioritized tests, including configuration and parameter variations, bit-for-bit evaluation, and plots of model variables to indicate where differences occur. LIVVkit also provides an easily extensible framework to incorporate and analyze results of new intercomparison projects, new observation data, and new computing platforms. LIVVkit is designed for quick adaptation to additional ice sheet models via abstraction of model specific code, functions, and configurations into an ice sheet model description bundle outside the main LIVVkit structure. Ultimately, through shareable and accessible analysis output, LIVVkit is intended to help developers build confidence in their models and enhance the credibility of ice sheet models overall.

The influence of discovery learning model application to the higher order thinking skills student of Srijaya Negara Senior High School Palembang on the animal kingdom subject matter

NASA Astrophysics Data System (ADS)

Riandari, F.; Susanti, R.; Suratmi

2018-05-01

This study aimed to find out the information in concerning the influence of discovery learning model application to the higher order thinking skills at the tenth grade students of Srijaya Negara senior high school Palembang on the animal kingdom subject matter. The research method used was pre-experimental with one-group pretest-posttest design. The researchconducted at Srijaya Negara senior high school Palembang academic year 2016/2017. The population sample of this research was tenth grade students of natural science 2. Purposive sampling techniquewas applied in this research. Data was collected by(1) the written test, consist of pretest to determine the initial ability and posttest to determine higher order thinking skills of students after learning by using discovery learning models. (2) Questionnaire sheet, aimed to investigate the response of the students during the learning process by using discovery learning models. The t-test result indicated there was significant increasement of higher order thinking skills students. Thus, it can be concluded that the application of discovery learning modelhad a significant effect and increased to higher order thinking skills students of Srijaya Negara senior high school Palembang on the animal kingdom subject matter.

Novel Task Functionalized Biopolymers for Enhanced Change Detection in Support of C-IED Operations

DTIC Science & Technology

2013-04-15

biopolymer was tested. All materials tested, PAM, chitin , the native biopolymer, and the MU conjugated biopolymer, were applied in small soil plots...phaseoli Strain 127 K36. Carbohydr. Res. 117, 141-156. EPA. 2001. Chitin ; Poly-N-acetyl-D-glucosamine (128991) Fact Sheet. USEPA Fact Sheet

Modes of Modelling Assessment--A Literature Review

ERIC Educational Resources Information Center

Frejd, Peter

2013-01-01

This paper presents a critical review of literature investigating assessment of mathematical modelling. Written tests, projects, hands-on tests, portfolio and contests are modes of modelling assessment identified in this study. The written tests found in the reviewed papers draw on an atomistic view on modelling competencies, whereas projects are…

Criteria to Evaluate Interpretive Guides for Criterion-Referenced Tests

ERIC Educational Resources Information Center

Trapp, William J.

2007-01-01

This project provides a list of criteria for which the contents of interpretive guides written for customized, criterion-referenced tests can be evaluated. The criteria are based on the "Standards for Educational and Psychological Testing" (1999) and examine the content breadth of interpretive guides. Interpretive guides written for…

Airline Transport Pilot-Airplane (Air Carrier) Written Test Guide.

ERIC Educational Resources Information Center

Federal Aviation Administration (DOT), Washington, DC. Flight Standards Service.

Presented is information useful to applicants who are preparing for the Airline Transport Pilot-Airplane (Air Carrier) Written Test. The guide describes the basic aeronautical knowledge and associated requirements for certification, as well as information on source material, instructions for taking the official test, and questions that are…

The Effects of Written Comments on Student Performance.

ERIC Educational Resources Information Center

Leauby, Bruce A.; Atkinson, Maryanne

1989-01-01

Three accounting teachers gave two tests and a comprehensive final to 417 undergraduates using one of three treatments: no comments written on test paper, comments at teacher's discretion, or standard comments. The type of comment did not affect subsequent test performance, but did significantly affect performance on final exam, especially for…

Formability of Annealed Ni-Ti Shape Memory Alloy Sheet

NASA Astrophysics Data System (ADS)

Fann, K. J.; Su, J. Y.; Chang, C. H.

2018-03-01

Ni-Ti shape memory alloy has two specific properties, superelasiticity and shape memory effect, and thus is widely applied in diverse industries. To extend its application, this study attempts to investigate the strength and cold formability of its sheet blank, which is annealed at various temperatures, by hardness test and by Erichsen-like cupping test. As a result, the higher the annealing temperature, the lower the hardness, the lower the maximum punch load as the sheet blank fractured, and the lower the Erichsen-like index or the lower the formability. In general, the Ni-Ti sheet after annealing has an Erichsen-like index between 8 mm and 9 mm. This study has also confirmed via DSC that the Ni-Ti shape memory alloy possesses the austenitic phase and shows the superelasticity at room temperature.

Smart photonic coating for civil engineering field: for a future inspection technology on concrete bridge

NASA Astrophysics Data System (ADS)

Fudouzi, Hiroshi; Tsuchiya, Koichi; Todoroki, Shin-ichi; Hyakutake, Tsuyoshi; Nitta, Hiroyuki; Nishizaki, Itaru; Tanaka, Yoshikazu; Ohya, Takao

2017-04-01

Here we will propose the conceptual new idea of the inspection of concrete bridge using smart materials and mobile IoT system. We apply opal photonic crystal film to detect cracks on concrete infrastructures. High quality opal photonic crystal films were coated on black color PET sheet over 1000 cm2 area. The opal film sheet was cut and adhered to concrete or mortar test pieces by epoxy resin. In the tensile test, the structural color of the opal sheet was changed when the crack was formed. As a demonstration, we have installated the opal film sheet on the wall of the concrete bridge. Our final purpose is the color change will be recorded by portable CCD devices, and send to expert via IoT network.

Development of a Cell Sheet Transportation Technique for Regenerative Medicine

PubMed Central

Oie, Yoshinori; Nozaki, Takayuki; Takayanagi, Hiroshi; Hara, Susumu; Hayashi, Ryuhei; Takeda, Shizu; Mori, Keisuke; Moriya, Noboru; Soma, Takeshi; Tsujikawa, Motokazu; Saito, Kazuo

2014-01-01

Purpose: A transportation technique for cell sheets is necessary to standardize regenerative medicine. The aim of this article is to develop and evaluate a new transportation technique for cell sheets. Material and Methods: We developed a transportation container with three basic functions: the maintenance of interior temperature, air pressure, and sterility. The interior temperature and air pressure were monitored by a recorder. Human oral mucosal epithelial cells obtained from two healthy volunteers were cultured on temperature-responsive culture dishes. The epithelial cell sheets were transported via an airplane between the Osaka University and Tohoku University using the developed cell transportation container. Histological and immunohistochemical analyses and flow cytometric analyses for cell viability and cell purity were performed for the cell sheets before and 12 h after transportation to assess the influence of transportation on the cell sheets. Sterility tests and screening for endotoxin and mycoplasma in the cell sheets were performed before and after transportation. Results: During transportation via an airplane, the temperature inside the container was maintained above 32°C, and the changes in air pressure remained within 10 hPa. The cell sheets were well stratified and successfully harvested before and after transportation. The expression patterns of keratin 3/76, p63, and MUC16 were equivalent before and after transportation. However, the expression of ZO-1 in the cell sheet after transportation was slightly weaker than that before transportation. The cell viability was 72.0% before transportation and 77.3% after transportation. The epithelial purity was 94.6% before transportation and 87.9% after transportation. Sterility tests and screening for endotoxin and mycoplasma were negative for all cell sheets. Conclusion: The newly developed transportation technique for air travel is essential technology for regenerative medicine and promotes the standardization and spread of regenerative therapies. PMID:24044382

Development of a cell sheet transportation technique for regenerative medicine.

PubMed

Oie, Yoshinori; Nozaki, Takayuki; Takayanagi, Hiroshi; Hara, Susumu; Hayashi, Ryuhei; Takeda, Shizu; Mori, Keisuke; Moriya, Noboru; Soma, Takeshi; Tsujikawa, Motokazu; Saito, Kazuo; Nishida, Kohji

2014-05-01

A transportation technique for cell sheets is necessary to standardize regenerative medicine. The aim of this article is to develop and evaluate a new transportation technique for cell sheets. We developed a transportation container with three basic functions: the maintenance of interior temperature, air pressure, and sterility. The interior temperature and air pressure were monitored by a recorder. Human oral mucosal epithelial cells obtained from two healthy volunteers were cultured on temperature-responsive culture dishes. The epithelial cell sheets were transported via an airplane between the Osaka University and Tohoku University using the developed cell transportation container. Histological and immunohistochemical analyses and flow cytometric analyses for cell viability and cell purity were performed for the cell sheets before and 12 h after transportation to assess the influence of transportation on the cell sheets. Sterility tests and screening for endotoxin and mycoplasma in the cell sheets were performed before and after transportation. During transportation via an airplane, the temperature inside the container was maintained above 32°C, and the changes in air pressure remained within 10 hPa. The cell sheets were well stratified and successfully harvested before and after transportation. The expression patterns of keratin 3/76, p63, and MUC16 were equivalent before and after transportation. However, the expression of ZO-1 in the cell sheet after transportation was slightly weaker than that before transportation. The cell viability was 72.0% before transportation and 77.3% after transportation. The epithelial purity was 94.6% before transportation and 87.9% after transportation. Sterility tests and screening for endotoxin and mycoplasma were negative for all cell sheets. The newly developed transportation technique for air travel is essential technology for regenerative medicine and promotes the standardization and spread of regenerative therapies.

The role of membrane-like stresses in determining the stability and sensitivity of the Antarctic ice sheets: back pressure and grounding line motion.

PubMed

Hindmarsh, Richard C A

2006-07-15

Membrane stresses act along thin bodies which are relatively well lubricated on both surfaces. They operate in ice sheets because the bottom is either sliding, or is much less viscous than the top owing to stress and heat softening of the basal ice. Ice streams flow over very well lubricated beds, and are restrained at their sides. The ideal of the perfectly slippery bed is considered in this paper, and the propagation of mechanical effects along an ice stream considered by applying spatially varying horizontal body forces. Propagation distances depend sensitively on the rheological index, and can be very large for ice-type rheologies.A new analytical solution for ice-shelf profiles and grounded tractionless stream profiles is presented, which show blow up of the profile in a finite distance upstream at locations where the flux is non-zero. This is a feature of an earlier analytical solution for a floating shelf.The length scale of decay of membrane stresses from the grounding line is investigated through scale analysis. In ice sheets, such effects decay over distances of several tens of kilometres, creating a vertical boundary layer between sheet flow and shelf flow, where membrane stresses adjust. Bounded, physically reasonable steady surface profiles only exist conditionally in this boundary layer. Where bounded steady profiles exist, adjacent profile equilibria for the whole ice sheet corresponding to different grounded areas occur (neutral equilibrium). If no solution in the boundary layer can exist, the ice-sheet profile must change.The conditions for existence can be written in terms of whether the basal rate factor (sliding or internal deformation) is too large to permit a steady solution. The critical value depends extremely sensitively on ice velocity and the back stress applied at the grounding line. High ice velocity and high stress both favour the existence of solutions and stability. Changes in these parameters can cause the steady solution existence criterion to be traversed, and the ice-sheet dynamics to change.A finite difference model which represents both neutral equilibrium and the dynamical transition is presented, and preliminary investigations into its numerical sensitivity are carried out. Evidence for the existence of a long wavelength instability is presented through the solution of a numerical eigenproblem, which will hamper predictability.

PolarPortal.org Communicates Real-Time Developments in the Arctic

NASA Astrophysics Data System (ADS)

Langen, P. L.; Andersen, S. B.; Andersen, K. K.; Andersen, M. L.; Ahlstrom, A. P.; van As, D.; Barletta, V. R.; Box, J. E.; Citterio, M.; Colgan, W. T.; Dybkjær, G.; Forsberg, R.; Høyer, J. L.; Jensen, M. B.; Kliem, N.; Mottram, R.; Nielsen, K. P.; Olesen, M.; Quaglia, F. C.; Rasmussen, T. A.; Rodehacke, C. B.; Stendel, M.; Sandberg Sørensen, L.; Tonboe, R. T.

2014-12-01

PolarPortal.org was launched in June 2013 by a consortium of Danish institutions, including the Danish Meteorological Institute (DMI), the Geological Survey of Denmark and Greenland (GEUS) and the National Space Institute at the Technical University of Denmark (DTU-Space). Polar Portal is a single web portal presenting a wide range of near real-time information on both the Greenland ice sheet and Arctic sea-ice in a format geared for non-specialists. Polar Portal aims to meet widespread public interest in a diverse range of climate-cryosphere processes in the Arctic: What is the present Greenland ice sheet contribution to sea level rise? How quickly are outlet glaciers retreating or advancing right now? How extensive is Arctic sea-ice or how warm is the Arctic Ocean at this moment? Although public interest in such topics is widely acknowledged, an important primary task for the scientists behind Polar Portal was collaborating with media specialists to establish the knowledge range of the general public on these topics, in order for Polar Portal to appropriately present useful climate-cryosphere information. Consequently, Polar Portal is designed in a highly visual exploratory format, where individual data products are accompanied by plain written summaries, with hyperlinks to relevant journal papers for more scrutinizing users. Numerous satellite and in situ observations, together with model output, are channeled daily into the Greenland ice sheet and Arctic sea-ice divisions of Polar Portal.

Development of a low energy micro sheet forming machine

NASA Astrophysics Data System (ADS)

Razali, A. R.; Ann, C. T.; Shariff, H. M.; Kasim, N. I.; Musa, M. A.; Ahmad, A. F.

2017-10-01

It is expected that with the miniaturization of materials being processed, energy consumption is also being `miniaturized' proportionally. The focus of this study was to design a low energy micro-sheet-forming machine for thin sheet metal application and fabricate a low direct current powered micro-sheet-forming machine. A prototype of low energy system for a micro-sheet-forming machine which includes mechanical and electronic elements was developed. The machine was tested for its performance in terms of natural frequency, punching forces, punching speed and capability, energy consumption (single punch and frequency-time based). Based on the experiments, the machine can do 600 stroke per minute and the process is unaffected by the machine's natural frequency. It was also found that sub-Joule of power was required for a single stroke of punching/blanking process. Up to 100micron thick carbon steel shim was successfully tested and punched. It concludes that low power forming machine is feasible to be developed and be used to replace high powered machineries to form micro-products/parts.

A preliminary investigation of projectile shape effects in hypervelocity impact of a double-sheet structure

NASA Technical Reports Server (NTRS)

Morrison, R. H.

1972-01-01

Impact tests of a sphere and several cylinders of various masses and fineness ratios, all of aluminum, fired into an aluminum double-sheet structure at velocities near 7 km/sec, show that a cylinder, impacting in the direction of its axis, is considerably more effective as a penetrator than a sphere. Impacts of three cylinders of equal mass, but different fineness ratios, produced holes through the structures' rear sheet, whereas impact of a sphere of the same mass did not. Moreover, it was found that to prevent rear-sheet penetration, the mass of the 1/2-fineness-ratio cylinder had to be reduced by a factor greater than three. Further tests wherein the cylinder diameter was held constant while the cylinder length was systematically reduced showed that a cylinder with a fineness ratio of 0.07 and a mass of only 1/7 that of the sphere was still capable of producing a hole in the rear sheet.

Springback evaluation of friction stir welded TWB automotive sheets

NASA Astrophysics Data System (ADS)

Kim, Junehyung; Lee, Wonoh; Chung, Kyung-Hwan; Kim, Daeyong; Kim, Chongmin; Okamoto, Kazutaka; Wagoner, R. H.; Chung, Kwansoo

2011-02-01

Springback behavior of automotive friction stir welded TWB (tailor welded blank) sheets was experimentally investigated and the springback prediction capability of the constitutive law was numerically validated. Four automotive sheets, aluminum alloy 6111-T4, 5083-H18, 5083-O and dual-phase DP590 steel sheets, each having one or two different thicknesses, were considered. To represent mechanical properties, the modified Chaboche type combined isotropic-kinematic hardening law was utilized along with the non-quadratic orthogonal anisotropic yield function, Yld2000-2d, while the anisotropy of the weld zone was ignored for simplicity. For numerical simulations, mechanical properties previously characterized [1] were applied. For validation purposes, three springback tests including the unconstrained cylindrical bending, 2-D draw bending and OSU draw-bend tests were carried out. The numerical method performed reasonably well in analyzing all verification tests and it was confirmed that the springback of TWB as well as of base samples is significantly affected by the ratio of the yield stress with respect to Young's modulus and thickness.

Experimental Characterization and Material Modelling of an AZ31 Magnesium Sheet Alloy at Elevated Temperatures under Consideration of the Tension-Compression Asymmetry

NASA Astrophysics Data System (ADS)

Behrens, B.-A.; Bouguecha, A.; Bonk, C.; Dykiert, M.

2017-09-01

Magnesium sheet alloys have a great potential as a construction material in the aerospace and automotive industry. However, the current state of research regarding temperature dependent material parameters for the description of the plastic behaviour of magnesium sheet alloys is scarce in literature and accurate statements concerning yield criteria and appropriate characterization tests to describe the plastic behaviour of a magnesium sheet alloy at elevated temperatures in deep drawing processes are to define. Hence, in this paper the plastic behaviour of the well-established magnesium sheet alloy AZ31 has been characterized by means of convenient mechanical tests (e. g. tension, compression and biaxial tests) at temperatures between 180 and 230 °C. In this manner, anisotropic and hardening behaviour as well as differences between the tension-compression asymmetry of the yield locus have been estimated. Furthermore, using the evaluated data from the above mentioned tests, two different yield criteria have been parametrized; the commonly used Hill’48 and an orthotropic yield criterion, CPB2006, which was developed especially for materials with hexagonal close packed lattice structure and is able to describe an asymmetrical yielding behaviour regarding tensile and compressive stress states. Numerical simulations have been finally carried out with both yield functions in order to assess the accuracy of the material models.

Development of user interface and of the data base "Earth, Moon and Planets" in the VBA environment for teaching students in the Kazan state universities

NASA Astrophysics Data System (ADS)

Petrova, N.; Tatarinov, P.; Akutina, M.

2009-04-01

In the frame of bachelor and master's degree diploma work the students accumulate and do structure distribution of necessary information about the spin-orbital, dynamical and geophysical characteristics of a planet. The information about the every planet is written into Excel WorkBook, the spreadsheets of which are the data base. The names of sheets reflect their content: "General Data", "Dynamics", "Geophysics", "Engineering", "References", Slides" etc. These data are taken from the last scientific articles dedicated to the modern problems of the planetary investigations. Especial interest is connected to the Lunar sciences - last data about surface mineral distribution, crust thickness and gravity field, slides with photographies received by Video Camera and various instruments situated on the board of Lunar SELENE mission (Japan, 2007-2009 yrs). The work with the data base is executed, using elements of the object-oriented programming. The students study to include into the UserForms standard means of Windows - Dialog Windows, TextBox, CommandButton, ComboBox, ScrollBar etc., and to support these elements by the macros written in programming language VBA. The main attention in the software support of the data base is done onto opportunity to investigate the two-three layer structure of a planet via modeling of its free nutation periods - Chandler-like Wobbles, Free Core Nutation, Inner Core Wobbles and Free Inner Core Nitation and their engineering estimation for space mission observations. The results are presented in the form of tables in Sheets and of diagrams constructed by special buttons of the UserForms on the basis of the calculated tables. The research was supported by the Russian-Japanese grant RFFI-JSPS N 07-02-91212, (2007 - 2009).

Preforming of polydioxanone sheets for orbital wall fractures - A technical note.

PubMed

Kruber, Daniel; Hierl, Thomas; Doerfler, Hans-Martin; Huempfner-Hierl, Heike; Krause, Matthias

2018-07-01

Polydioxanone (PDS) sheets are commonly used in the treatment of orbital wall fractures. A potential drawback of PDS is that it may be difficult to adapt to the anatomy of the orbital walls. Therefore a study was conceived to test the feasibility of preforming PDS sheets. PDS sheet material was water-heated and preformed using a template based on a statistical anatomical model. Then the deformed sheet was cooled, stored and compared to the original model to investigate post-deformation changes. PDS sheet material could easily be deformed using a mould. No significant post-cooling shape changes were noticed. PDS sheet material can be preformed into complex geometric shapes. This could be a benefit in the treatment of orbital wall fractures. Copyright © 2018 European Association for Cranio-Maxillo-Facial Surgery. Published by Elsevier Ltd. All rights reserved.

Ground Instructor Written Test Guide--Basic-Advanced. Revised 1972.

ERIC Educational Resources Information Center

Federal Aviation Administration (DOT), Washington, DC. Flight Standards Service.

The test guide was prepared to assist applicants who are preparing for the Ground Instructor Written Test. It supersedes the 1967 examination guide. The guide outlines the scope of the basic aeronautical knowledge requirements for a ground instructor; acquaints the applicant with source material that may be used to acquire this basic knowledge;…

The Effects of a Translation Bias on the Scores for the "Basic Economics Test"

ERIC Educational Resources Information Center

Hahn, Jinsoo; Jang, Kyungho

2012-01-01

International comparisons of economic understanding generally require a translation of a standardized test written in English into another language. Test results can differ based on how researchers translate the English written exam into one in their own language. To confirm this hypothesis, two differently translated versions of the "Basic…

Development of lightweight graphite/polyimide sandwich panels, phases 3, 4 and 5

NASA Technical Reports Server (NTRS)

Merlette, J. B.

1972-01-01

Work performed in the last three phases of the program included: (1) face sheet processing; (2) honeycomb core manufacture; (3) face sheet-to-core bonding development; and (4) sandwich panel fabrication and testing. Resin cure studies were a major portion of this effort since processing problems traced to the polyimide matrix resin had to be resolved before quality core and face sheets could be fabricated. Honeycomb core fabrication and testing were conducted by Hexcel Corporation. A total of four graphite/polyimide resin composite cores were fabricated, tested, and reported. Two sandwich panels weighing .48 and .58 lb/sq ft, respectively were designed and fabricated which meet the support structure loads for the shuttle orbiter thermal protection system.

LIVVkit: An extensible, python-based, land ice verification and validation toolkit for ice sheet models

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kennedy, Joseph H.; Bennett, Andrew R.; Evans, Katherine J.

To address the pressing need to better understand the behavior and complex interaction of ice sheets within the global Earth system, significant development of continental-scale, dynamical ice sheet models is underway. Concurrent to the development of the Community Ice Sheet Model (CISM), the corresponding verification and validation (V&V) process is being coordinated through a new, robust, Python-based extensible software package, the Land Ice Verification and Validation toolkit (LIVVkit). Incorporated into the typical ice sheet model development cycle, it provides robust and automated numerical verification, software verification, performance validation, and physical validation analyses on a variety of platforms, from personal laptopsmore » to the largest supercomputers. LIVVkit operates on sets of regression test and reference data sets, and provides comparisons for a suite of community prioritized tests, including configuration and parameter variations, bit-for-bit evaluation, and plots of model variables to indicate where differences occur. LIVVkit also provides an easily extensible framework to incorporate and analyze results of new intercomparison projects, new observation data, and new computing platforms. LIVVkit is designed for quick adaptation to additional ice sheet models via abstraction of model specific code, functions, and configurations into an ice sheet model description bundle outside the main LIVVkit structure. Furthermore, through shareable and accessible analysis output, LIVVkit is intended to help developers build confidence in their models and enhance the credibility of ice sheet models overall.« less

LIVVkit: An extensible, python-based, land ice verification and validation toolkit for ice sheet models

DOE PAGES

Kennedy, Joseph H.; Bennett, Andrew R.; Evans, Katherine J.; ...

2017-03-23

To address the pressing need to better understand the behavior and complex interaction of ice sheets within the global Earth system, significant development of continental-scale, dynamical ice sheet models is underway. Concurrent to the development of the Community Ice Sheet Model (CISM), the corresponding verification and validation (V&V) process is being coordinated through a new, robust, Python-based extensible software package, the Land Ice Verification and Validation toolkit (LIVVkit). Incorporated into the typical ice sheet model development cycle, it provides robust and automated numerical verification, software verification, performance validation, and physical validation analyses on a variety of platforms, from personal laptopsmore » to the largest supercomputers. LIVVkit operates on sets of regression test and reference data sets, and provides comparisons for a suite of community prioritized tests, including configuration and parameter variations, bit-for-bit evaluation, and plots of model variables to indicate where differences occur. LIVVkit also provides an easily extensible framework to incorporate and analyze results of new intercomparison projects, new observation data, and new computing platforms. LIVVkit is designed for quick adaptation to additional ice sheet models via abstraction of model specific code, functions, and configurations into an ice sheet model description bundle outside the main LIVVkit structure. Furthermore, through shareable and accessible analysis output, LIVVkit is intended to help developers build confidence in their models and enhance the credibility of ice sheet models overall.« less

3D Printing of Thermo-Responsive Methylcellulose Hydrogels for Cell-Sheet Engineering.

PubMed

Cochis, Andrea; Bonetti, Lorenzo; Sorrentino, Rita; Contessi Negrini, Nicola; Grassi, Federico; Leigheb, Massimiliano; Rimondini, Lia; Farè, Silvia

2018-04-10

A possible strategy in regenerative medicine is cell-sheet engineering (CSE), i.e., developing smart cell culture surfaces from which to obtain intact cell sheets (CS). The main goal of this study was to develop 3D printing via extrusion-based bioprinting of methylcellulose (MC)-based hydrogels. Hydrogels were prepared by mixing MC powder in saline solutions (Na₂SO₄ and PBS). MC-based hydrogels were analyzed to investigate the rheological behavior and thus optimize the printing process parameters. Cells were tested in vitro on ring-shaped printed hydrogels; bulk MC hydrogels were used for comparison. In vitro tests used murine embryonic fibroblasts (NIH/3T3) and endothelial murine cells (MS1), and the resulting cell sheets were characterized analyzing cell viability and immunofluorescence. In terms of CS preparation, 3D printing proved to be an optimal approach to obtain ring-shaped CS. Cell orientation was observed for the ring-shaped CS and was confirmed by the degree of circularity of their nuclei: cell nuclei in ring-shaped CS were more elongated than those in sheets detached from bulk hydrogels. The 3D printing process appears adequate for the preparation of cell sheets of different shapes for the regeneration of complex tissues.

"The Eye of the Cyclone" - Teaching Natural Hazards in Schools by Using M-Learning and Augmented Reality Techniques

NASA Astrophysics Data System (ADS)

Ortwein, Annette; Schultz, Johannes; Rienow, Andreas

2017-04-01

Earth observation from space enables scientists and decision makers to forecast and react on the impacts of tropical storms. The project "Columbus Eye - Live-Imagery from the ISS in School Lessons" teaches pupils the implications of the coupled human-environment systems by applying remote sensing and digital image processing. Recently, Columbus Eye launched its first Android App featuring ISS videos. Generating a smartphone-based learning environment for working with ISS imagery introduces m-learning to the classrooms. The learning unit "The Eye of the Cyclone" addresses the formation and path of Philippine typhoon Maysak by using a multi-media approach. Based on a traditional work sheet, the diagrams of typhoon Maysak come alive when viewed through the smartphone's camera. A diagram of the typhoon's secret interior mechanics turns into a video of typhoon Maysak as seen from the ISS on 31st of March 2015, holding additional information on its unique specifications. The second diagram of air masses suddenly moves and shows the path of typhoon Maysak over time. But before those interactive parts are explored, the background information is presented in the work sheet by means of written scientific learning materials, including information on the occurrence, formation and inner structure of typhoons. Thus, fostering the reading competence, the pupils' understanding on the topic is assessed by several tasks on the work sheet's final page. The oral presentation explains how the haptic experience of writing the solutions on a sheet of paper makes the knowledge paperbound and "real", literally lifting pens & papers into space. In the light of the Copernicus services, it will be explained how Sentinel-based teaching units can be developed in order to communicating the knowledge and the handling of natural hazards in times of global change.

Texture and mechanical properties of Al-0.5Mg-1.0Si-0.5Cu alloy sheets manufactured via a cross rolling method

NASA Astrophysics Data System (ADS)

Jeon, Jae-Yeol; Son, Hyeon-Taek; Woo, Kee-Do; Lee, Kwang-Jin

2012-04-01

The relationship between the texture and mechanical properties of 6xxx aluminum alloy sheets processed via cross rolling was investigated. The microstructures of the conventional rolled and cross rolled sheets after annealing were analyzed using optical micrographs (OM). The texture distribution across the thickness in the Al-Mg-Si-Cu alloy, conventional rolled sheets, and cross rolled sheets both before and after annealing was investigated via X-ray texture measurements. The texture was analyzed in three layers from the surface to the center of the sheet. The β-fiber texture of the conventional rolled sheet was typical of the texture obtained using aluminumoll ring. After annealing, the typical β-fiber orientations were changed to recrystallization textures: cube{001}<100> and normal direction (ND)-rotated cubes. However, the texture of the cross rolled sheet was composed of an asymmetrical, rolling direction (RD)-rotated cubes. After annealing, the asymmetrical orientations in the cross rolled sheet were changed to a randomized texture. The average R-value of the annealed cross rolled sheets was higher than that of the conventional rolled sheets. The limit dome height (LDH) test results demonstrated that cross rolling is effective in improving the formability of the Al-Mg-Si-Cu alloy sheets.

Moldable cork ablation material

NASA Technical Reports Server (NTRS)

1977-01-01

A successful thermal ablative material was manufactured. Moldable cork sheets were tested for density, tensile strength, tensile elongation, thermal conductivity, compression set, and specific heat. A moldable cork sheet, therefore, was established as a realistic product.

Observations on the relationship of structure to the mechanical properties of thin TD-NiCr sheet

NASA Technical Reports Server (NTRS)

Whittenberger, J. D.

1976-01-01

A study of the relationship between structure and mechanical properties of thin TD-NiCr sheet indicated that the elevated temperature tensile, stress-rupture, and creep strength properties are dependent on grain aspect ratio and sheet thickness. In general, the strength properties increase with increasing grain aspect ratio and sheet thickness. Tensile testing revealed an absence of ductility at elevated temperatures (not less than 1144 K). Significant creep damage as determined by subsequent tensile testing at room temperature occurs after very small amounts (less than 0.1%) of prior creep deformation over the temperature range 1144-1477 K. A threshold stress for creep appears to exist. Creep exposure below the threshold stress at T not less than 1366 K results in almost full retention of room temperature tensile properties.

Modelling the climate and ice sheets of the mid-Pliocene warm period: a test of model dependency

NASA Astrophysics Data System (ADS)

Dolan, Aisling; Haywood, Alan; Lunt, Daniel; Hill, Daniel

2010-05-01

The mid-Pliocene warm period (MPWP; c. 3.0 - 3.3 million years ago) has been the subject of a large number of published studies during the last decade. It is an interval in Earth history, where conditions were similar to those predicted by climate models for the end of the 21st Century. Not only is it important to increase our understanding of the climate dynamics in a warmer world, it is also important to determine exactly how well numerical models can retrodict a climate significantly different from the present day, in order to have confidence in them for predicting the future climate. Previous General Circulation Model (GCM) simulations have indicated that MPWP mean annual surface temperatures were on average 2 to 3˚C warmer than the pre-industrial era. Coastal stratigraphy and benthic oxygen isotope records suggest that terrestrial ice volumes were reduced when compared to modern. Ice sheet modelling studies have supported this decrease in cryospheric extent. Generally speaking, both climate and ice sheet modelling studies have only used results from one numerical model when simulating the climate of the MPWP. However, recent projects such as PMIP (the Palaeoclimate Modelling Intercomparison Project) have emphasised the need to explore the dependency of past climate predictions on the specific climate model which is used. Here we present a comparison of MPWP climatologies produced by three atmosphere only GCMs from the Goddard Institute of Space Studies (GISS), the National Centre for Atmospheric Research (NCAR) and the Hadley Centre for Climate Prediction and Research (GCMAM3, CAM3-CLM and HadAM3 respectively). We focus on the ability of the GCMs to simulate climate fields needed to drive an offline ice sheet model to assess whether there are any significant differences between the climatologies. By taking the different temperature and precipitation predictions simulated by the three models as a forcing, and adopting GCM-specific topography, we have used the British Antarctic Survey thermomechanically coupled ice sheet model (BASISM) to test the extent to which equilibrium state ice sheets in the Northern Hemisphere are GCM dependent. Initial results which do not use GCM-specific topography suggest that employing different GCM climatologies with only small differences in surface air temperature and precipitation has a dramatic effect on the resultant Greenland ice sheet, where the end-member ice sheets vary from near modern to almost zero ice volume. As an extension of this analysis, we will also present results using a second ice sheet model (Glimmer), with a view to testing the degree to which end-member ice sheets are ice sheet model dependent, something which has not previously been addressed. Initially, BASISM and Glimmer will be internally optimised for performance, but we will also present a comparison where BASISM will be configured to the Glimmer model setup in a further test of ice sheet model dependency.

What Every Middle School Teacher Needs to Know about Reading Tests (From Someone Who Has Written Them)

ERIC Educational Resources Information Center

Fuhrken, Charles

2011-01-01

Tests require a special kind of savvy, a kind of critical thinking and knowledge application that is not always a part of classroom reading experiences. Who better to teach you how to prepare your students for reading tests than someone who has written them? Charles Fuhrken has spent years working with several major testing companies and…

EDUCATIONAL ATTAINMENT AND ATTITUDES TOWARD SCHOOL AS A FUNCTION OF FEEDBACK IN THE FORM OF TEACHERS' WRITTEN COMMENTS.

ERIC Educational Resources Information Center

SWEET, ROGER C.

RELATIONSHIPS BETWEEN A TEACHER'S WRITTEN COMMENTS ON A TEST AND (1) SUBSEQUENT STUDENT ATTAINMENT AS MEASURED BY TEST PERFORMANCE AND (2) ATTITUDE CHANGE TOWARD 9TH-GRADE ENGLISH, WERE INVESTIGATED. 9 CLASSES (225 STUDENTS) WERE GIVEN 4 TESTS BY THEIR TEACHERS OVER A 6-WEEK PERIOD. TESTS WERE RETURNED WITH NUMERICAL SCORES, LETTER GRADE, AND…

Laser based spot weld characterization

NASA Astrophysics Data System (ADS)

Jonietz, Florian; Myrach, Philipp; Rethmeier, Michael; Suwala, Hubert; Ziegler, Mathias

2016-02-01

Spot welding is one of the most important joining technologies, especially in the automotive industry. Hitherto, the quality of spot welded joints is tested mainly by random destructive tests. A nondestructive testing technique offers the benefit of cost reduction of the testing procedure and optimization of the fabrication process, because every joint could be examined. This would lead to a reduced number of spot welded joints, as redundancies could be avoided. In the procedure described here, the spot welded joint between two zinc-coated steel sheets (HX340LAD+Z100MB or HC340LA+ZE 50/50) is heated optically on one side. Laser radiation and flash light are used as heat sources. The melted zone, the so called "weld nugget" provides the mechanical stability of the connection, but also constitutes a thermal bridge between the sheets. Due to the better thermal contact, the spot welded joint reveals a thermal behavior different from the surrounding material, where the heat transfer between the two sheets is much lower. The difference in the transient thermal behavior is measured with time resolved thermography. Hence, the size of the thermal contact between the two sheets is determined, which is directly correlated to the size of the weld nugget, indicating the quality of the spot weld. The method performs well in transmission with laser radiation and flash light. With laser radiation, it works even in reflection geometry, thus offering the possibility of testing with just one-sided accessibility. By using heating with collimated laser radiation, not only contact-free, but also remote testing is feasible. A further convenience compared to similar thermographic approaches is the applicability on bare steel sheets without any optical coating for emissivity correction. For this purpose, a proper way of emissivity correction was established.

Fatigue Strength and Related Characteristics of Aircraft Joints I : Comparison of Spot-Weld and Rivet Patterns in 24s-t Alclad and 75s-t Alclad

NASA Technical Reports Server (NTRS)

Russell, H W; Jackson, L R; Grover, H J; Beaver, W W

1944-01-01

Report contains detailed results of a number of fatigue tests on spot-welded joints in aluminum alloys. The tests described include: (1) fatigue tests on spot-welded lap joints in sheets of unequal thickness of alclad 24s-t. These tests indicate that the fatigue strength of a spot-welded joint in sheets of two different gages is slightly higher than that of a similar joint in two sheets of the thinner gage but definitely lower than that of a similar joint in two sheets of the thicker gage. (2) Fatigue tests on spot-welded alclad 75s-t spot-welded lap-joint specimens of alclad 75s-t were not any stronger in fatigue than similar specimens of alclad 24s-t. (3) Fatigue tests on lap-joint specimens spot -welded after various surface preparations--these included ac welding wire-brushed surfaces, dc welding wire-brushed surfaces, and dc welding chemically cleaned surfaces. While the ac welds were strongest statically, the dc welds on wire-brushed surfaces were strongest in fatigue. Specimens prepared in this way were very nearly as strong as the best riveted specimens tested for comparison. (4) Fatigue tests on specimens spot-welded with varying voltage so as to include a wide range of static spot-weld strengths. The fatigue strengths were in the same order as the static strengths but showed less range. (author)

Process design of press hardening with gradient material property influence

NASA Astrophysics Data System (ADS)

Neugebauer, R.; Schieck, F.; Rautenstrauch, A.

2011-05-01

Press hardening is currently used in the production of automotive structures that require very high strength and controlled deformation during crash tests. Press hardening can achieve significant reductions of sheet thickness at constant strength and is therefore a promising technology for the production of lightweight and energy-efficient automobiles. The manganese-boron steel 22MnB5 have been implemented in sheet press hardening owing to their excellent hot formability, high hardenability, and good temperability even at low cooling rates. However, press-hardened components have shown poor ductility and cracking at relatively small strains. A possible solution to this problem is a selective increase of steel sheet ductility by press hardening process design in areas where the component is required to deform plastically during crash tests. To this end, process designers require information about microstructure and mechanical properties as a function of the wide spectrum of cooling rates and sequences and austenitizing treatment conditions that can be encountered in production environments. In the present work, a Continuous Cooling Transformation (CCT) diagram with corresponding material properties of sheet steel 22MnB5 was determined for a wide spectrum of cooling rates. Heating and cooling programs were conducted in a quenching dilatometer. Motivated by the importance of residual elasticity in crash test performance, this property was measured using a micro-bending test and the results were integrated into the CCT diagrams to complement the hardness testing results. This information is essential for the process design of press hardening of sheet components with gradient material properties.

Process design of press hardening with gradient material property influence

DOE Office of Scientific and Technical Information (OSTI.GOV)

Neugebauer, R.; Professorship for Machine Tools and Forming Technology, TU Chemnitz; Schieck, F.

Press hardening is currently used in the production of automotive structures that require very high strength and controlled deformation during crash tests. Press hardening can achieve significant reductions of sheet thickness at constant strength and is therefore a promising technology for the production of lightweight and energy-efficient automobiles. The manganese-boron steel 22MnB5 have been implemented in sheet press hardening owing to their excellent hot formability, high hardenability, and good temperability even at low cooling rates. However, press-hardened components have shown poor ductility and cracking at relatively small strains. A possible solution to this problem is a selective increase of steelmore » sheet ductility by press hardening process design in areas where the component is required to deform plastically during crash tests. To this end, process designers require information about microstructure and mechanical properties as a function of the wide spectrum of cooling rates and sequences and austenitizing treatment conditions that can be encountered in production environments. In the present work, a Continuous Cooling Transformation (CCT) diagram with corresponding material properties of sheet steel 22MnB5 was determined for a wide spectrum of cooling rates. Heating and cooling programs were conducted in a quenching dilatometer. Motivated by the importance of residual elasticity in crash test performance, this property was measured using a micro-bending test and the results were integrated into the CCT diagrams to complement the hardness testing results. This information is essential for the process design of press hardening of sheet components with gradient material properties.« less

Nurses' maths: researching a practical approach.

PubMed

Wilson, Ann

To compare a new practical maths test with a written maths test. The tests were undertaken by qualified nurses training for intravenous drug administration, a skill dependent on maths accuracy. The literature showed that the higher education institutes (HEIs) that provide nurse training use traditional maths tests, a practical way of testing maths had not been described. Fifty five nurses undertook two maths tests based on intravenous drug calculations. One was a traditional written test. The second was a new type of test using a simulated clinical environment. All participants were also interviewed one week later to ascertain their thoughts and feelings about the tests. There was a significant improvement in maths test scores for those nurses who took the practical maths test first. It is suggested that this is because it improved their conceptualisation skills and thus helped them to achieve accuracy in their calculations. Written maths tests are not the best way to help and support nurses in acquiring and improving their maths skills and should be replaced by a more practical approach.

49 CFR Appendix E to Part 240 - Recommended Procedures for Conducting Skill Performance Tests

Code of Federal Regulations, 2014 CFR

2014-10-01

... experience difficulty in establishing an objective method of measuring an individual's skill level. Any... employ a written aid to help record events and procedures that as a minimum should be observed for when... developing such a written aid so as to ensure meaningful testing. When conducting a skills performance test...

49 CFR Appendix E to Part 240 - Recommended Procedures for Conducting Skill Performance Tests

Code of Federal Regulations, 2013 CFR

2013-10-01

... experience difficulty in establishing an objective method of measuring an individual's skill level. Any... employ a written aid to help record events and procedures that as a minimum should be observed for when... developing such a written aid so as to ensure meaningful testing. When conducting a skills performance test...

49 CFR Appendix E to Part 240 - Recommended Procedures for Conducting Skill Performance Tests

Code of Federal Regulations, 2012 CFR

2012-10-01

... experience difficulty in establishing an objective method of measuring an individual's skill level. Any... employ a written aid to help record events and procedures that as a minimum should be observed for when... developing such a written aid so as to ensure meaningful testing. When conducting a skills performance test...

Using Plickers as an Assessment Tool in Health and Physical Education Settings

ERIC Educational Resources Information Center

Chng, Lena; Gurvitch, Rachel

2018-01-01

Written tests are one of the most common assessment tools classroom teachers use today. Despite its popularity, administering written tests or surveys, especially in health and physical education settings, is time consuming. In addition to the time taken to type and print out the tests or surveys, health and physical education teachers must grade…

30 CFR 250.1508 - What must I do when MMS administers written or oral tests?

Code of Federal Regulations, 2010 CFR

2010-07-01

... oral tests? 250.1508 Section 250.1508 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Well Control and Production Safety Training § 250.1508 What must I do when MMS administers written or oral tests? MMS or its...

Relation of structure to mechanical properties of thin thoria dispersion strengthened nickel-chromium (TD-NiCr alloy sheet

NASA Technical Reports Server (NTRS)

Whittenberger, J. D.

1975-01-01

A study of the relation between structure and mechanical properties of thin TD-NiCr sheet indicated that the elevated temperature tensile, stress-rupture, and creep strength properties depend primarily on the grain aspect ratio and sheet thickness. In general, the strength properties increased with increasing grain aspect ratio and sheet thickness. Tensile testing revealed an absence of ductility at elevated temperatures. A threshold stress for creep appears to exist. Even small amounts of prior creep deformation at elevated temperatures can produce severe creep damage.

Recruitment of ethnic minorities into cancer clinical trials: experience from the front lines.

PubMed

Symonds, R P; Lord, K; Mitchell, A J; Raghavan, D

2012-09-25

Throughout the world there are problems recruiting ethnic minority patients into cancer clinical trials. A major barrier to trial entry may be distrust of research and the medical system. This may be compounded by the regulatory framework governing research with an emphasis on written consent, closed questions and consent documentation, as well as fiscal issues. The Leicester UK experience is that trial accrual is better if British South Asian patients are approached by a senior doctor rather than someone of perceived lesser hierarchical status and a greater partnership between the hospital and General Practitioner may increase trial participation of this particular ethnic minority. In Los Angeles, USA, trial recruitment was improved by a greater utilisation of Hispanic staff and a Spanish language-based education programme. Involvement of community leaders is essential. While adhering to national, legal and ethnical standards, information sheets and consent, it helps if forms can be tailored towards the local ethnic minority population. Written translations are often of limited value in the recruitment of patients with no or limited knowledge of English. In some cultural settings, tape-recorded verbal consent (following approval presentations) may be an acceptable substitute for written consent, and appropriate legislative changes should be considered to facilitate this option. Approaches should be tailored to specific minority populations, taking consideration of their unique characteristics and with input from their community leadership.

Durability improvements of two-dimensional metal nanoparticle sheets by molecular cross-linked structures between nanoparticles

NASA Astrophysics Data System (ADS)

Saito, Noboru; Ryuzaki, Sou; Wang, Pangpang; Park, Susie; Sakai, Nobuyuki; Tatsuma, Tetsu; Okamoto, Koichi; Tamada, Kaoru

2018-03-01

The durability of two-dimensional metal nanoparticle sheets is a crucial factor for realizing next-generation optoelectronic devices based on plasmonics such as organic light-emitting diodes. Here, we report improvements in the durability of Ag nanoparticle sheets by forming alkanedithiol (DT16) cross-linked structures between the nanoparticles. The cross-linked structures in a sheet were fabricated by the self-assembly of DT16-capped Ag nanoparticles with 10% coverage (AgDT16). The durabilities for thermal, organic solvent, and oxidation reactions of AgDT16 sheets were found to be improved owing to the cross-linked structures by comparing Ag nanoparticle sheets without the cross-linked structures. The absorbance spectra revealed that the Ag nanoparticle sheets without the structure are markedly damaged by each durability test, whereas the AgDT16 sheets remain. The molecular cross-linked structures between nanoparticles in two-dimansional metal nanoparticle sheets were found to have the potential to play a key role in the realization of plasmonic optoelectronic devices including metal nanoparticles.

Market Research on Law School Student Aid Award Letters and Shopping Sheet Information. NASFAA Consumer Information & Law Student Indebtedness Task Force Report

ERIC Educational Resources Information Center

National Association of Student Financial Aid Administrators, 2016

2016-01-01

"Market Research on Law School Student Aid Award Letters and Shopping Sheet Information" set out to identify through consumer testing what information on the financial aid award letter and U.S. Department of Education's (ED) Shopping Sheet could be modified to create a document that better assists students applying to, or currently…

Omega Hawaii Antenna System: Modification and Validation Tests. Volume 2. Data Sheets.

DTIC Science & Technology

1979-10-19

a benchmark because of potential hotel construction . DS 5-1 DATA SHEET 5 (DS-5) RADIO FIELD INTENSITY MEASUREMENTS OMEGA STATION: HAWAII SITE NO. C 1A...27.5 1008 11.05 26.5 1007 Ft 11.80 28.1 COMMENT Not considered for a benchmark because of potential hotel construction . DS 5-5 DATA SHEET 5 (DS-5) RADIO

Skylab-3 handheld photography alphabetized geographical features list

NASA Technical Reports Server (NTRS)

Mcniel, J. L.; Deyalcourt, C. C.

1974-01-01

The data was thoroughly researched using the Times Index-Gazetteer of the World, the Times Atlas of the World, and the National Atlas of the United States of America to ensure correct spelling and location of named features. The spelling and major geographical features applied to smaller features (minor) such as cities, towns, mountain peaks, etc., are in accordance with these publications. It is understood that some political boundaries and names of countries are subject to change. The data was written on NASA keypunch transmittal sheets and punched into data cards. These data cards were then machine sorted alphabetically by major feature and minor feature.

49 CFR 238.503 - Inspection, testing, and maintenance requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... inspection, testing, or maintenance task under this part. (i) Standard procedures. The program under paragraph (a) of this section shall include the railroad's written standard procedures for performing all... this section shall contain the railroad's written procedures to ensure that all systems and components...

Development of adapted GMR-probes for automated detection of hidden defects in thin steel sheets

NASA Astrophysics Data System (ADS)

Pelkner, Matthias; Pohl, Rainer; Kreutzbruck, Marc; Commandeur, Colin

2016-02-01

Thin steel sheets with a thickness of 0.3 mm and less are the base materials of many everyday life products (cans, batteries, etc.). Potential inhomogeneities such as non-metallic inclusions inside the steel can lead to a rupture of the sheets when it is formed into a product such as a beverage can. Therefore, there is a need to develop automated NDT techniques to detect hidden defects and inclusions in thin sheets during production. For this purpose Tata Steel Europe and BAM, the Federal Institute for Materials Research and Testing (Germany), collaborate in order to develop an automated NDT-system. Defect detection systems have to be robust against external influences, especially when used in an industrial environment. In addition, such a facility has to achieve a high sensitivity and a high spatial resolution in terms of detecting small inclusions in the μm-regime. In a first step, we carried out a feasibility study to determine which testing method is promising for detecting hidden defects and inclusions inside ferrous thin steel sheets. Therefore, two methods were investigated in more detail - magnetic flux leakage testing (MFL) using giant magneto resistance sensor arrays (GMR) as receivers [1,2] and eddy current testing (ET). The capabilities of both methods were tested with 0.2 mm-thick steel samples containing small defects with depths ranging from 5 µm up to 60 µm. Only in case of GMR-MFL-testing, we were able to detect parts of the hidden defects with a depth of 10 µm trustworthily with a SNR better than 10 dB. Here, the lift off between sensor and surface was 250 µm. On this basis, we investigated different testing scenarios including velocity tests and different lift offs. In this contribution we present the results of the feasibility study leading to first prototypes of GMR-probes which are now installed as part of a demonstrator inside a production line.

Method and apparatus for determining weldability of thin sheet metal

DOEpatents

Goodwin, Gene M.; Hudson, Joseph D.

1988-01-01

A fixture is provided for testing thin sheet metal specimens to evaluate hot-cracking sensitivity for determining metal weldability on a heat-to-heat basis or through varying welding parameters. A test specimen is stressed in a first direction with a load selectively adjustable over a wide range and then a weldment is passed along over the specimen in a direction transverse to the direction of strain to evaluate the hot-cracking characteristics of the sheet metal which are indicative of the weldability of the metal. The fixture provides evaluations of hot-cracking sensitivity for determining metal weldability in a highly reproducible manner with minimum human error.

Numerical study of the current sheet and PSBL in a magnetotail model

NASA Technical Reports Server (NTRS)

Doxas, I.; Horton, W.; Sandusky, K.; Tajima, T.; Steinolfson, R.

1989-01-01

The current sheet and plasma sheet boundary layer (PSBL) in a magnetotail model are discussed. A test particle code is used to study the response of ensembles of particles to a two-dimensional, time-dependent model of the geomagnetic tail, and test the proposition (Coroniti, 1985a, b; Buchner and Zelenyi, 1986; Chen and Palmadesso, 1986; Martin, 1986) that the stochasticity of the particle orbits in these fields is an important part of the physical mechanism for magnetospheric substorms. The realistic results obtained for the fluid moments of the particle distribution with this simple model, and their insensitivity to initial conditions, is consistent with this hypothesis.

[Quality of the anesthesiologist written record during the transfer of postoperative patients: Influence of implementing a structured communication tool].

PubMed

García-Sánchez, M J; Fernández-Guerrero, C; López-Toribio, P; Bueno-Cavanillas, A; Prieto-Cuéllar, M; Guzmán-Malpica, E M; Cuevas-Valenzuela, P; Moreno-Abril, E; Lara-Ramos, P

2014-01-01

The lack of communication is a major cause of health care errors, especially during patient transfer between practitioners and/or healthcare units, when standardization of communication is a recommended practice. In our study we wanted to assess whether the application of the structured communication SBAR tool could influence the quality of the information written on the progress sheet by the anesthesiologist involved in the transfer of the patient after surgery. This is an observational, retrospective, randomized, quality review of the written record made by the anesthesiologist during the transfer of patients from the surgical area to the postoperative recovery unit, by applying a validated list. We evaluated three observation periods: a control period of two months in 2011 (preSBAR) and a second period of two months in 2012 (postSBAR); in the latter two groups of patients were transferred (postSBAR +) or without SBAR (postSBAR-). The strength of agreement between raters obtained an intraclass correlation coefficient of 0.8459 (p <0.001). There were significant differences in the study group, with highest average score in the group with SBAR (postSBAR + group: mean ± SD 7.56 ± 1.20 versus postSBAR-group: 5.41 ± 2.98, p <0.001) and depending on the anesthesiologist responsible for the intervention participated in the study (mean ± SD: 7.00 ± 1.99, compared to 4.81 ± 3.24 in the non-participants, p <0.001). There was an improvement in the quality of written records made in 2012 during the implementation of the SBAR, without the actual application of this instrument appearing to influence it. The anesthesiologists that were involved in new forms of patient safety were also those who made written records of highest quality. Copyright © 2013 Sociedad Española de Anestesiología, Reanimación y Terapéutica del Dolor. Published by Elsevier España. All rights reserved.

The Steady Flow Resistance of Perforated Sheet Materials in High Speed Grazing Flows

NASA Technical Reports Server (NTRS)

Syed, Asif A.; Yu, Jia; Kwan, H. W.; Chien, E.; Jones, Michael G. (Technical Monitor)

2002-01-01

A study was conducted to determine the effects of high speed grazing air flow on the acoustic resistance of perforated sheet materials used in the construction of acoustically absorptive liners placed in commercial aircraft engine nacelles. Since DC flow resistance of porous sheet materials is known to be a major component of the acoustic resistance of sound suppression liners, the DC flow resistance of a set of perforated face-sheets and linear 'wiremesh' face-sheets was measured in a flow duct apparatus (up to Mach 0.8). Samples were fabricated to cover typical variations in perforated face-sheet parameters, such as hole diameter, porosity and sheet thickness, as well as those due to different manufacturing processes. The DC flow resistance data from perforated sheets were found to correlate strongly with the grazing flow Mach number and the face-sheet porosity. The data also show correlation against the boundary layer displacement thickness to hole-diameter ratio. The increase in resistance with grazing flow for punched aluminum sheets is in good agreement with published results up to Mach 0.4, but is significantly larger than expected above Mach 0.4. Finally, the tests demonstrated that there is a significant increase in the resistance of linear 'wiremesh' type face-sheet materials.

78 FR 79675 - Guidance to Federal Financial Assistance Recipients Regarding Title VI Prohibition Against...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-12-31

... written translations. --Competency to interpret, however, does not necessarily mean formal certification... free language assistance. --Written tests that do not assess English language competency, but test... States read, write, speak and understand English. There are many individuals, however, for whom English...

Increased correlation coefficient between the written test score and tutors' performance test scores after training of tutors for assessment of medical students during problem-based learning course in Malaysia.

PubMed

Jaiprakash, Heethal; Min, Aung Ko Ko; Ghosh, Sarmishtha

2016-03-01

This paper is aimed at finding if there was a change of correlation between the written test score and tutors' performance test scores in the assessment of medical students during a problem-based learning (PBL) course in Malaysia. This is a cross-sectional observational study, conducted among 264 medical students in two groups from November 2010 to November 2012. The first group's tutors did not receive tutor training; while the second group's tutors were trained in the PBL process. Each group was divided into high, middle and low achievers based on their end-of-semester exam scores. PBL scores were taken which included written test scores and tutors' performance test scores. Pearson correlation coefficient was calculated between the two kinds of scores in each group. The correlation coefficient between the written scores and tutors' scores in group 1 was 0.099 (p<0.001) and for group 2 was 0.305 (p<0.001). The higher correlation coefficient in the group where tutors received the PBL training reinforces the importance of tutor training before their participation in the PBL course.

A review and assessment of Virginia's license plate sheeting specifications.

DOT National Transportation Integrated Search

2003-01-01

At the request of Virginia's Secretary of Transportation, the Virginia Transportation Research Council undertook a review and assessment of Virginia's license plate sheeting specifications. The review was focused on the five test methods or specifica...

Semen Analysis

MedlinePlus

... Booklets Pruebas diagnósticas para la infertilidad masculina (Diagnostic tests for male infertility) From: Spanish Fact Sheets & Info Booklets Assisted reproductive technology 辅助生殖技术辅助生殖技术 From: Chinese Fact Sheets & Info Booklets Diagnostic ...

Investigation to Identify Performance Criteria and Test Methods for Evaluating Single-Ply Roofing Systems.

DTIC Science & Technology

1987-03-01

Reinforced Black EPDM Rubber Sheets for Use in Roofing Applications ( Rubber Manufacturers Association [RMAJ, 1984). Minimum Requirements for Fabric-Reinforced...Black Polychloroprene Rubber Sheets for Use in Roofing Applications (RMA, 1984). Minimum Requirements for Non-Reinforced Black EPDM Rubber Sheets for...and materials. The Rubber Manufacturers Amoeiation (RMA) (USA) RMA is funding a study in conjunction with ASTM to evaluate three different EPDM

3D Printing of Thermo-Responsive Methylcellulose Hydrogels for Cell-Sheet Engineering

PubMed Central

Cochis, Andrea; Sorrentino, Rita; Grassi, Federico; Leigheb, Massimiliano; Farè, Silvia

2018-01-01

A possible strategy in regenerative medicine is cell-sheet engineering (CSE), i.e., developing smart cell culture surfaces from which to obtain intact cell sheets (CS). The main goal of this study was to develop 3D printing via extrusion-based bioprinting of methylcellulose (MC)-based hydrogels. Hydrogels were prepared by mixing MC powder in saline solutions (Na2SO4 and PBS). MC-based hydrogels were analyzed to investigate the rheological behavior and thus optimize the printing process parameters. Cells were tested in vitro on ring-shaped printed hydrogels; bulk MC hydrogels were used for comparison. In vitro tests used murine embryonic fibroblasts (NIH/3T3) and endothelial murine cells (MS1), and the resulting cell sheets were characterized analyzing cell viability and immunofluorescence. In terms of CS preparation, 3D printing proved to be an optimal approach to obtain ring-shaped CS. Cell orientation was observed for the ring-shaped CS and was confirmed by the degree of circularity of their nuclei: cell nuclei in ring-shaped CS were more elongated than those in sheets detached from bulk hydrogels. The 3D printing process appears adequate for the preparation of cell sheets of different shapes for the regeneration of complex tissues. PMID:29642573

Boosting protein stability with the computational design of β-sheet surfaces.

PubMed

Kim, Doo Nam; Jacobs, Timothy M; Kuhlman, Brian

2016-03-01

β-sheets often have one face packed against the core of the protein and the other facing solvent. Mutational studies have indicated that the solvent-facing residues can contribute significantly to protein stability, and that the preferred amino acid at each sequence position is dependent on the precise structure of the protein backbone and the identity of the neighboring amino acids. This suggests that the most advantageous methods for designing β-sheet surfaces will be approaches that take into account the multiple energetic factors at play including side chain rotamer preferences, van der Waals forces, electrostatics, and desolvation effects. Here, we show that the protein design software Rosetta, which models these energetic factors, can be used to dramatically increase protein stability by optimizing interactions on the surfaces of small β-sheet proteins. Two design variants of the β-sandwich protein from tenascin were made with 7 and 14 mutations respectively on its β-sheet surfaces. These changes raised the thermal midpoint for unfolding from 45°C to 64°C and 74°C. Additionally, we tested an empirical approach based on increasing the number of potential salt bridges on the surfaces of the β-sheets. This was not a robust strategy for increasing stability, as three of the four variants tested were unfolded. © 2016 The Protein Society.

5 CFR 315.608 - Noncompetitive appointment of certain former overseas employees.

Code of Federal Regulations, 2011 CFR

2011-01-01

... written test after determining that the duties and responsibilities of the applicant's overseas position were similar enough to make the written test unnecessary. (1) Tenure. A person appointed under this... individual, for example, ill health or personal interest in relocating. (d) Time limit on eligibility. An...

5 CFR 315.608 - Noncompetitive appointment of certain former overseas employees.

Code of Federal Regulations, 2013 CFR

2013-01-01

... written test after determining that the duties and responsibilities of the applicant's overseas position were similar enough to make the written test unnecessary. (1) Tenure. A person appointed under this... individual, for example, ill health or personal interest in relocating. (d) Time limit on eligibility. An...

The Assessment of Athletics "Knowledge" with Written and Video Tests

ERIC Educational Resources Information Center

van Vuuren-Cassar, Gemma; Lamprianou, Iasonas

2006-01-01

Background: Athletics programmes for secondary schools include a variety of skills, knowledge and cognitive abilities, which are currently assessed through written, practical, oral and/or video-based tests. Skills are traditionally taught in practice-based sessions, while the knowledge aspect is often reinforced in class-based sessions with…

10 CFR 431.12 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-01-01

...) Standard 112-1996, Test Procedure for Polyphase Induction Motors and Generators, and Test Method (1) of CSA... a system, that has its own rules of procedure and management, for giving written assurance that a... operated by an entity independent of both the party seeking the written assurance and the party providing...

10 CFR 431.12 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-01-01

...) Standard 112-1996, Test Procedure for Polyphase Induction Motors and Generators, and Test Method (1) of CSA... a system, that has its own rules of procedure and management, for giving written assurance that a... operated by an entity independent of both the party seeking the written assurance and the party providing...

Differential prediction of FAA Academy performance on the basis of gender and written air traffic control specialist aptitude test scores.

DOT National Transportation Integrated Search

1996-04-01

The technical fairness of the written air traffic control specialist (ATCS) aptitude test battery was investigated within the framework of the Uniform Guidelines on Employee Selection Procedures (29 CFR 1607). First, the adverse impact of using a com...

Hecules Fact Sheet.EPA.May 2011.final

EPA Pesticide Factsheets

EPA Region 4 fact sheet from May 2011 about a 3013 order to Hercules, Inc. in Hattiesburg, MS to conduct on- and off-site monitoring, testing, and reporting the nature and extent of any environmental contamination at their facility.

Environmental Technology Verification Program Fact Sheet

EPA Science Inventory

This is a Fact Sheet for the ETV Program. The EPA Environmental Technology Verification Program (ETV) develops test protocols and verifies the performance of innovative technologies that have the potential to improve protection of human health and the environment. The program ...

Free Wake Techniques for Rotor Aerodynamic Analylis. Volume 2: Vortex Sheet Models

NASA Technical Reports Server (NTRS)

Tanuwidjaja, A.

1982-01-01

Results of computations are presented using vortex sheets to model the wake and test the sensitivity of the solutions to various assumptions used in the development of the models. The complete codings are included.

Detection of Steel Fatigue Cracks with Strain Sensing Sheets Based on Large Area Electronics

PubMed Central

Yao, Yao; Glisic, Branko

2015-01-01

Reliable early-stage damage detection requires continuous monitoring over large areas of structure, and with sensors of high spatial resolution. Technologies based on Large Area Electronics (LAE) can enable direct sensing and can be scaled to the level required for Structural Health Monitoring (SHM) of civil structures and infrastructure. Sensing sheets based on LAE contain dense arrangements of thin-film strain sensors, associated electronics and various control circuits deposited and integrated on a flexible polyimide substrate that can cover large areas of structures. This paper presents the development stage of a prototype strain sensing sheet based on LAE for crack detection and localization. Two types of sensing-sheet arrangements with size 6 × 6 inch (152 × 152 mm) were designed and manufactured, one with a very dense arrangement of sensors and the other with a less dense arrangement of sensors. The sensing sheets were bonded to steel plates, which had a notch on the boundary, so the fatigue cracks could be generated under cyclic loading. The sensors within the sensing sheet that were close to the notch tip successfully detected the initialization of fatigue crack and localized the damage on the plate. The sensors that were away from the crack successfully detected the propagation of fatigue cracks based on the time history of the measured strain. The results of the tests have validated the general principles of the proposed sensing sheets for crack detection and identified advantages and challenges of the two tested designs. PMID:25853407

Effects of structured written feedback by cards on medical students' performance at Mini Clinical Evaluation Exercise (Mini-CEX) in an outpatient clinic.

PubMed

Haghani, Fariba; Hatef Khorami, Mohammad; Fakhari, Mohammad

2016-07-01

Feedback cards are recommended as a feasible tool for structured written feedback delivery in clinical education while effectiveness of this tool on the medical students' performance is still questionable.  The purpose of this study was to compare the effects of structured written feedback by cards as well as verbal feedback versus verbal feedback alone on the clinical performance of medical students at the Mini Clinical Evaluation Exercise (Mini-CEX) test in an outpatient clinic. This is a quasi-experimental study with pre- and post-test comprising four groups in two terms of medical students' externship. The students' performance was assessed through the Mini-Clinical Evaluation Exercise (Mini-CEX) as a clinical performance evaluation tool. Structured written feedbacks were given to two experimental groups by designed feedback cards as well as verbal feedback, while in the two control groups feedback was delivered verbally as a routine approach in clinical education. By consecutive sampling method, 62 externship students were enrolled in this study and seven students were excluded from the final analysis due to their absence for three days. According to the ANOVA analysis and Post Hoc Tukey test,  no statistically significant difference was observed among the four groups at the pre-test, whereas a statistically significant difference was observed between the experimental and control groups at the post-test  (F = 4.023, p =0.012). The effect size of the structured written feedbacks on clinical performance was 0.19. Structured written feedback by cards could improve the performance of medical students in a statistical sense. Further studies must be conducted in other clinical courses with longer durations.

A laser-sheet flow visualization technique for the large wind tunnels of the National Full-Scale Aerodynamics Complex

NASA Technical Reports Server (NTRS)

Reinath, M. S.; Ross, J. C.

1990-01-01

A flow visualization technique for the large wind tunnels of the National Full Scale Aerodynamics Complex (NFAC) is described. The technique uses a laser sheet generated by the NFAC Long Range Laser Velocimeter (LRLV) to illuminate a smoke-like tracer in the flow. The LRLV optical system is modified slightly, and a scanned mirror is added to generate the sheet. These modifications are described, in addition to the results of an initial performance test conducted in the 80- by 120-Foot Wind Tunnel. During this test, flow visualization was performed in the wake region behind a truck as part of a vehicle drag reduction study. The problems encountered during the test are discussed, in addition to the recommended improvements needed to enhance the performance of the technique for future applications.

Results of the Greenland ice sheet model initialisation experiments: ISMIP6 - initMIP-Greenland

NASA Astrophysics Data System (ADS)

Goelzer, Heiko; Nowicki, Sophie; Edwards, Tamsin; Beckley, Matthew

2017-04-01

Ice sheet model initialisation has a large effect on projected future sea-level contributions and gives rise to important uncertainties. The goal of this intercomparison exercise for the continental-scale Greenland ice sheet is therefore to compare, evaluate and improve the initialisation techniques used in the ice sheet modelling community. The initMIP-Greenland project is the first in a series of ice sheet model intercomparison activities within ISMIP6 (Ice Sheet Model Intercomparison Project for CMIP6). The experimental set-up has been designed to allow comparison of the initial present-day state of the Greenland ice sheet between participating models and against observations. Furthermore, the initial states are tested with two schematic forward experiments to evaluate the initialisation in terms of model drift (forward run without any forcing) and response to a large perturbation (prescribed surface mass balance anomaly). We present and discuss results that highlight the wide diversity of data sets, boundary conditions and initialisation techniques used in the community to generate initial states of the Greenland ice sheet.

Thermal properties of highly structured composite and aluminium sheets in an aerodynamic tunnel

NASA Astrophysics Data System (ADS)

Kulhavy, Petr; Egert, Josef

This article deals with the thermodynamic behaviour of heat shields - structured metal and composite plates. Experiments have been carried out in a wind tunnel with an additional heating, which simulates the heat source from engine or exhaust pipe and simultaneously the airflow generated during a car movement. The tested sheets with hexagonal structure were a standard commercial made of aluminium and a second manufactured by replication (lamination, diffusion) from glass fabric. The airflow in a parallel way along the sheets was analysed experimentally in order to determine the heat transfer efficiency between surfaces of sheets and surrounding airflow. The temperature on the sheets was chosen to observe the effects of different sheets material, various heat power and airflow velocity. During the experiment a thermal input below the sheets and airflow velocity through the tunnel have been changed. The thermal field distribution on the metal sheet is different than in case of composite sheet. For the composite material the thermal field distribution was more homogeneous. This article describe briefly also methods of obtaining real composite geometry based on scanned data and their reconstruction for using in some future numerical models.

Ductile Tearing Resistance Indexing of Automotive Grade DP 590 Steel Sheets: EWF Testing Using DENT Specimens

NASA Astrophysics Data System (ADS)

Sahoo, Subhadra; Padmapriya, N.; De, Partha Sarathi; Chakraborti, P. C.; Ray, S. K.

2018-03-01

The essential work of fracture (EWF) method has been explored for indexing the ductile tearing resistance of DP 590 automotive grade dual-phase steel sheet both in longitudinal (L-T) and transverse (T-L) orientations. The simplest possible test and analysis procedures have been adopted. The EWF method is found to be eminently suitable for routine quality control and product development purposes for such materials. Areas for further research for improving the experimental strategy are highlighted. For the investigated steel sheet, the estimated tearing resistance is found to be distinctly higher for the L-T orientation compared to the T-L orientation; the reason thereof merits further investigation.

Alternative plasticizer, 4-cyclohexene-1,2-dicarboxylic acid dinonyl ester, for blood containers with protective effects on red blood cells and improved cold resistance.

PubMed

Morishita, Yuki; Nomura, Yusuke; Fukui, Chie; Fujisawa, Ayano; Watanabe, Kayo; Fujimaki, Hideo; Kumada, Hidefumi; Inoue, Kaoru; Morikawa, Tomomi; Takahashi, Miwa; Kawakami, Tsuyoshi; Sakoda, Hideyuki; Mukai, Tomokazu; Yuba, Toshiyasu; Inamura, Ken-Ichi; Tanoue, Akito; Miyazaki, Ken-Ichi; Chung, Ung-Il; Ogawa, Kumiko; Yoshida, Midori; Haishima, Yuji

2018-04-01

Di (2-ethylhexyl) phthalate (DEHP), a typical plasticizer used for polyvinyl chloride (PVC), is eluted from PVC-made blood containers and protects against red blood cell (RBC) hemolysis. However, concerns have arisen regarding the reproductive and developmental risks of DEHP in humans, and the use of alternative plasticizers for medical devices has been recommended worldwide. In this study, we propose that the use of a novel plasticizer, 4-cyclohexene-1,2-dicarboxylic acid dinonyl ester (DL9TH), could help produce more useful and safe blood containers. PVC sheet containing DL9TH and di (2-ethylhexyl) 4-cyclohexene-1,2-dicarboxylate (DOTH) provides comparable or superior protective effects to RBCs relative to PVC sheet containing DEHP or di-isononyl-cyclohexane-1,2-dicarboxylate (DINCH ® , an alternative plasticizer that has been used in PVC sheets for blood containers). The total amount of plasticizer eluted from DOTH/DL9TH-PVC sheets is nearly the same as that eluted from DEHP-PVC sheets. In addition, DOTH/DL9TH-PVC has better cold resistance than DEHP- and DINCH ® -PVC sheets. In vitro and in vivo tests for biological safety based on International Organization for Standardization guidelines (10993 series) suggest that the DOTH/DL9TH-PVC sheet can be used safely. Subchronic toxicity testing of DL9TH in male rats in accordance with the principles of Organisation for Economic Co-operation and Development Test Guideline 408 showed that DL9TH did not induce adverse effects up to the highest dose level tested (717 mg/kg body weight/day). There were no effects on testicular histopathology and sperm counts, and no indications of endocrine effects: testosterone, thyroid-stimulating hormone, follicle-stimulating hormone, and 17β-estradiol were unchanged by the treatment, compared with the control group. © 2017 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 106B: 1052-1063, 2018. © 2017 Wiley Periodicals, Inc.

Assessing Deaf Children's Written Language

ERIC Educational Resources Information Center

Steinkamp, Marjorie W.; Quigley, Stephen P.

1977-01-01

Described is the development of the Test of Syntactical Abilities (TSA), an instrument for measuring deaf children's ability to comprehend and produce syntactically correct written sentences. (Author/IM)

Concurrent Validity and Classification Accuracy of Curriculum-Based Measurement for Written Expression

ERIC Educational Resources Information Center

Furey, William M.; Marcotte, Amanda M.; Hintze, John M.; Shackett, Caroline M.

2016-01-01

The study presents a critical analysis of written expression curriculum-based measurement (WE-CBM) metrics derived from 3- and 10-min test lengths. Criterion validity and classification accuracy were examined for Total Words Written (TWW), Correct Writing Sequences (CWS), Percent Correct Writing Sequences (%CWS), and Correct Minus Incorrect…

Report to Lincoln Labs on TWPAs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dubois, J.; Carosi, G.; Woollett, N.

2017-09-26

This past spring LLNL’s Quantum Sensor’s team received two TWPA amplifiers from Lincoln Labs along with a data-sheet explaining handling, operations and expected performance. Here we will outline some of the initial tests performed on this amplifiers as part of LLNL’s Quantum Sensors Strategic Initiative (QSSI). Initial testing confirmed that both amplifiers worked and provided gain and SNR improvement similar to that called out in the data-sheets provided.

Elastic behavior and onset of cracking in cement composite plates reinforced by perforated thin steel sheets

NASA Astrophysics Data System (ADS)

Aronchik, V.

1996-03-01

Thin cement mortar plates reinforced by perforated thin steel sheets have been tested in four-point flexure loading. Six kinds of sheet reinforcement and to additional ones (for control) were used. Perforated sheets of the Daugavpils Factory of Machinery Chains differed by their thickness (0.6-1.8 mm), shape (round, rectangular, oval, "dumbbell"), and mark of steel (St. 08, 50, 70). Dimensions of plantes were 100×20×2 cm. Cements-sand mortar with a 1∶2 ratio of cement PZ35 and river sand of 3 mm grains was used as a matrix. Control specimens of similar dimensions and matrix were reinforced by wire cages and meshes (ferrocement). The testing was performed using an UMM-5 testing machine. Maximum deflection (at the midspan), tension, and shear strains were recorded. The expeimental data are presented in tables and graphs. The testing results showed that the elasticity modulus of material was in good agreement with the "admixture rule;" an onset of cracking for all types (excluding one) practically did not differ from reference samples; the mode of fracture in typical cases included an adhesion failure and significant shear strains. In one case the limit of the tension strength of the reinforcement was achieved.

HAER COLO,30LAKWD.V,2G (sheet 1 of 1) Glenn L. Martin ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

HAER COLO,30-LAKWD.V,2G- (sheet 1 of 1) - Glenn L. Martin Company, Titan Missile Test Facilities, Cold Flow Laboratory Building B, Waterton Canyon Road & Colorado Highway 121, Lakewood, Jefferson County, CO

A new tensile impact test for the toughness characterization of sheet material

NASA Astrophysics Data System (ADS)

Könemann, Markus; Lenz, David; Brinnel, Victoria; Münstermann, Sebastian

2018-05-01

In the past, the selection of suitable steels has been carried out primarily based on the mechanical properties of different steels. One of these properties is the resistance against crack propagation. For many constructions, this value plays an important role, because it can compare the impact toughness of different steel grades easily and gives information about the loading capacity of the specific materials. For thin sheets, impact toughness properties were usually not considered. One of the reasons for this is that the Charpy-impact test is not applicable for sheets with thicknesses below 2 mm. For a long time, this was not relevant because conventional steels had a sufficient impact toughness in a wide temperature range. However, since new multiphase steel grades with improved mechanical property exploitations are available, it turned out that impact toughness properties need to be considered during the component design phase, as the activation of the cleavage fracture mechanism is observed under challenging loading conditions. Therefore, this work aims to provide a new and practical testing procedure for sheet material or thin walled structures. The new testing procedure is based on tensile tests conducted in an impact pendulum similar to the Charpy impact hammer. A new standard geometry is provided, which enables a comparison between different steels or steel grades. A connection to the conventional Charpy test is presented using a damage mechanics model, which predicts material failure with consideration of to the stress state at various temperatures. Different specimen geometries are analysed to cover manifold stress states. A special advantage of the damage mechanics model is also the possibility to predict the materials behaviour in the transition area. To verify the method a conventional steel was tested in Charpy tests as well as in the new tensile impact test.

Characterising ductility of 6xxx-series aluminium sheet alloys at combined loading conditions

NASA Astrophysics Data System (ADS)

Henn, Philipp; Liewald, Mathias; Sindel, Manfred

2017-10-01

This paper presents a new approach to characterise material ductility when combined, three dimensional loading conditions occurring during vehicle crash are applied. So called "axial crush test" of closed hat sections is simplified by reducing it down to a two-dimensional testing procedure. This newly developed edge-compression test (ECT) provides the opportunity to investigate a defined characteristic axial folding behaviour of a profile edge. The potential to quantify and to differentiate crashworthiness of material by use of new edge-compression test is investigated by carrying out experimental studies with two different 6xxx-aluminium sheet alloys.

Preventing Stalled Quality Improvement Teams: A Written Test of Project Selectionability.

ERIC Educational Resources Information Center

Bacdayan, Paul

2002-01-01

Discusses organizations' use of quality improvement teams in total quality management and how they can benefit from training team personnel in how to select projects with a low risk of stalling. Describes an efficient written assessment test of project selection ability designed for those who conduct evaluations of training sessions. (Author/LRW)

22 CFR 11.2 - Written examination for appointment to class 7 or 8.

Code of Federal Regulations, 2012 CFR

2012-04-01

... written examination is designed to permit the Board to test the candidate's intelligence, breadth and quality of knowledge, and understanding. It will consist of three parts: (1) A general ability test, (2... designated cities in the United States and at Foreign Service posts on dates established by the Board of...

22 CFR 11.2 - Written examination for appointment to class 7 or 8.

Code of Federal Regulations, 2013 CFR

2013-04-01

... written examination is designed to permit the Board to test the candidate's intelligence, breadth and quality of knowledge, and understanding. It will consist of three parts: (1) A general ability test, (2... designated cities in the United States and at Foreign Service posts on dates established by the Board of...

22 CFR 11.2 - Written examination for appointment to class 7 or 8.

Code of Federal Regulations, 2010 CFR

2010-04-01

... written examination is designed to permit the Board to test the candidate's intelligence, breadth and quality of knowledge, and understanding. It will consist of three parts: (1) A general ability test, (2... designated cities in the United States and at Foreign Service posts on dates established by the Board of...

22 CFR 11.2 - Written examination for appointment to class 7 or 8.

Code of Federal Regulations, 2011 CFR

2011-04-01

... written examination is designed to permit the Board to test the candidate's intelligence, breadth and quality of knowledge, and understanding. It will consist of three parts: (1) A general ability test, (2... designated cities in the United States and at Foreign Service posts on dates established by the Board of...

22 CFR 11.2 - Written examination for appointment to class 7 or 8.

Code of Federal Regulations, 2014 CFR

2014-04-01

... written examination is designed to permit the Board to test the candidate's intelligence, breadth and quality of knowledge, and understanding. It will consist of three parts: (1) A general ability test, (2... designated cities in the United States and at Foreign Service posts on dates established by the Board of...

Reaction of photochemical resists used in screen printing under the influence of digitally modulated ultra violet light

NASA Astrophysics Data System (ADS)

Gmuender, T.

2017-02-01

Different chemical photo-reactive emulsions are used in screen printing for stencil production. Depending on the bandwidth, optical power and depth of field from the optical system, the reaction / exposure speed has a diverse value. In this paper, the emulsions get categorized and validated in a first step. After that a mathematical model gets developed and adapted due to heuristic experience to estimate the exposure speed under the influence of digitally modulated ultra violet (UV) light. The main intention is to use the technical specifications (intended wavelength, exposure time, distance to the stencil, electrical power, stencil configuration) in the emulsion data sheet primary written down with an uncertainty factor for the end user operating with large projector arc lamps and photo films. These five parameters are the inputs for a mathematical formula which gives as an output the exposure speed for the Computer to Screen (CTS) machine calculated for each emulsion / stencil setup. The importance of this work relies in the possibility to rate with just a few boundaries the performance and capacity of an exposure system used in screen printing instead of processing a long test series for each emulsion / stencil configuration.

Equilibrium and Stability Properties of Low Aspect Ratio Mirror Systems: from Neutron Source Design to the Parker Spiral

NASA Astrophysics Data System (ADS)

Peterson, Ethan; Anderson, Jay; Clark, Mike; Egedal, Jan; Endrizzi, Douglass; Flanagan, Ken; Harvey, Robert; Lynn, Jacob; Milhone, Jason; Wallace, John; Waleffe, Roger; Mirnov, Vladimir; Forest, Cary

2017-10-01

Equilibrium reconstructions of rotating magnetospheres in the lab are computed using a user-friendly extended Grad-Shafranov solver written in Python and various magnetic and kinetic measurements. The stability of these equilibria are investigated using the NIMROD code with two goals: understand the onset of the classic ``wobble'' in the heliospheric current sheet and demonstrating proof-of-principle for a laboratory source of high- β turbulence. Using the same extended Grad-Shafranov solver, equilibria for an axisymmetric, non-paraxial magnetic mirror are used as a design foundation for a high-field magnetic mirror neutron source. These equilibria are numerically shown to be stable to the m=1 flute instability, with higher modes likely stabilized by FLR effects; this provides stability to gross MHD modes in an axisymmetric configuration. Numerical results of RF heating and neutral beam injection (NBI) from the GENRAY/CQL3D code suite show neutron fluxes promising for medical radioisotope production as well as materials testing. Synergistic effects between NBI and high-harmonic fast wave heating show large increases in neutron yield for a modest increase in RF power. work funded by DOE, NSF, NASA.

Repair and retrofit of concrete bridge girders using hybrid FRP sheets.

DOT National Transportation Integrated Search

2012-02-01

The use of carbon fibers (CF) and glass fibers (GF) were combined to strengthen potentially non-ductile flexural : members. Based on tension tests of fiber-reinforced polymer (FRP) rovings and sheets, as well as theoretical : research on hybrid FRP, ...

Response of the Antarctic ice sheet to ocean forcing using the POPSICLES coupled ice sheet-ocean model

NASA Astrophysics Data System (ADS)

Martin, D. F.; Asay-Davis, X.; Price, S. F.; Cornford, S. L.; Maltrud, M. E.; Ng, E. G.; Collins, W.

2014-12-01

We present the response of the continental Antarctic ice sheet to sub-shelf-melt forcing derived from POPSICLES simulation results covering the full Antarctic Ice Sheet and the Southern Ocean spanning the period 1990 to 2010. Simulations are performed at 0.1 degree (~5 km) ocean resolution and ice sheet resolution as fine as 500 m using adaptive mesh refinement. A comparison of fully-coupled and comparable standalone ice-sheet model results demonstrates the importance of two-way coupling between the ice sheet and the ocean. The POPSICLES model couples the POP2x ocean model, a modified version of the Parallel Ocean Program (Smith and Gent, 2002), and the BISICLES ice-sheet model (Cornford et al., 2012). BISICLES makes use of adaptive mesh refinement to fully resolve dynamically-important regions like grounding lines and employs a momentum balance similar to the vertically-integrated formulation of Schoof and Hindmarsh (2009). Results of BISICLES simulations have compared favorably to comparable simulations with a Stokes momentum balance in both idealized tests like MISMIP3D (Pattyn et al., 2013) and realistic configurations (Favier et al. 2014). POP2x includes sub-ice-shelf circulation using partial top cells (Losch, 2008) and boundary layer physics following Holland and Jenkins (1999), Jenkins (2001), and Jenkins et al. (2010). Standalone POP2x output compares well with standard ice-ocean test cases (e.g., ISOMIP; Losch, 2008) and other continental-scale simulations and melt-rate observations (Kimura et al., 2013; Rignot et al., 2013). A companion presentation, "Present-day circum-Antarctic simulations using the POPSICLES coupled land ice-ocean model" in session C027 describes the ocean-model perspective of this work, while we focus on the response of the ice sheet and on details of the model. The figure shows the BISICLES-computed vertically-integrated ice velocity field about 1 month into a 20-year coupled Antarctic run. Groundling lines are shown in green.

Determination of Flaw Growth Characteristics of Ti-6Al-4V Sheet in the Solution-Treated and Aged Condition

NASA Technical Reports Server (NTRS)

Hoeppner, David W.; Pettit, Donald E.; Feddersen, Charles E.; Hyler, Walter S.

1968-01-01

The specific experimental investigation undertaken was designed to answer these questions on Ti-6Al-4V in the solution treated and aged condition. The defect growth and fracture characteristics were studied in parent (unwelded) and welded sheet material. The results of the study indicate that cryogenic proof testing will screen smaller size defects than proof testing at ambient conditions. However some unusual crack growth behavior during the proof test simulation suggests that some further study be made of stress and time duration effects.

The Fatigue Characteristics of Bolted Lap Joints of 24S-T Alclad Sheet Materials

DTIC Science & Technology

1946-10-01

extremely close bolt fits are needed to o%tain maximum life of bolt ~oint~ under repeated etreseeci. -. Szvzral ty~+?+s of bolt patterns hava been tegted...Memorial Institute on spec~meris of 0.102-i.nch sheet. In particular, figure 4 shows, on a load- life diagram, . results of tests Qn single-bolt...results of tests at the Univer- sity of’ il~~nols on single—bolt specimens, Tables 10 and 11 give reeults of tests, made at the U“ uiversity of Illino~8 , on

Lightweight Long Life Heat Exchanger

NASA Technical Reports Server (NTRS)

Moore, E. K.

1976-01-01

A shuttle orbiter flight configuration aluminum heat exchanger was designed, fabricated, and tested. The heat exchanger utilized aluminum clad titanium composite parting sheets for protection against parting sheet pin hole corrosion. The heat exchanger, which is fully interchangeable with the shuttle condensing heat exchanger, includes slurpers (a means for removing condensed water from the downstream face of the heat exchanger), and both the core air passes and slurpers were hydrophilic coated to enhance wettability. The test program included performance tests which demonstrated the adequacy of the design and confirmed the predicted weight savings.

Prediction of the Forming Limit Band for Steel Sheets using a new Formulation of Hora's Criterion (MMFC)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sorin Comsa, Dan; Dragos, George; Paraianu, Liana

2011-01-17

The paper analyzes the dispersion of the mechanical parameters and its influence on the forming limit curves of sheet metals. The tests have been made for the case of the DC01 steel sheets. The dispersion of the mechanical parameters has been observed during the experimental research. On the basis of this dispersion, a forming limit band has been calculated using an alternate formulation of Hora's model (MMFC).

Chemical vapor deposition growth

NASA Technical Reports Server (NTRS)

Ruth, R. P.; Manasevit, H. M.; Kenty, J. L.; Moudy, L. A.; Simpson, W. I.; Yang, J. J.

1976-01-01

The chemical vapor deposition (CVD) method for the growth of Si sheet on inexpensive substrate materials is investigated. The objective is to develop CVD techniques for producing large areas of Si sheet on inexpensive substrate materials, with sheet properties suitable for fabricating solar cells meeting the technical goals of the Low Cost Silicon Solar Array Project. Specific areas covered include: (1) modification and test of existing CVD reactor system; (2) identification and/or development of suitable inexpensive substrate materials; (3) experimental investigation of CVD process parameters using various candidate substrate materials; (4) preparation of Si sheet samples for various special studies, including solar cell fabrication; (5) evaluation of the properties of the Si sheet material produced by the CVD process; and (6) fabrication and evaluation of experimental solar cell structures, using standard and near-standard processing techniques.

Comprehension of Ambiguous and Other Polysemous Utterances: Presented in Written Mode.

ERIC Educational Resources Information Center

Brause, Rita S.

Designed to assess comprehension of written ambiguous and polysemous structures, this instrument is a series of written statements that include varying degrees and types of ambiguity. In the first part of the test students are asked to identify (from a choice of three) semantically acceptable paraphrases for an initial sentence. Then students must…

Development of 1500mm Wide Wrought Magnesium Alloys by Twin Roll Casting Technique in Turkey

NASA Astrophysics Data System (ADS)

Duygulu, Ozgur; Ucuncuoglu, Selda; Oktay, Gizem; Temur, Deniz Sultan; Yucel, Onuralp; Kaya, Ali Arslan

Magnesium alloy AZ31, AZ61, AZ91, AM50 and AM60 sheets were produced by twin roll casting first time in Turkey. Sheets of 4.5-6.5mm thick and 1500mm width were successfully achieved. Microstructure of the sheet was analyzed by optical microscope, scanning electron microscope (SEM) and transmission electron microscope (TEM). Semi-quantitative analyses were performed by SEM-EDS. In addition, X-ray studies were performed for both characterization and texture purposes. Mechanical properties were investigated by tensile tests and also hardness measurements. Homogenization and annealing heat treatments were performed on the produced sheets.

Development of a tornado safe room door from wood Products: door design and impact testing

Treesearch

Robert H. Falk; James J. Bridwell

2016-01-01

In this study, a tornado safe room door built from wood products and steel sheeting was developed and impact-tested according to tornado safe room standards. Results indicate that an door constructed from as few as two sheets of 23/32-in. (18.26-mm) construction-grade plywood and overlaid with 18-gauge (0.05-in.- (1.27- mm-) thick) steel can pass the required impact...

Characterization of the strain-life fatigue properties of thin sheet metal using an optical extensometer

NASA Astrophysics Data System (ADS)

Zhang, Shuiqiang; Mao, Shuangshuang; Arola, Dwayne; Zhang, Dongsheng

2014-09-01

Characterizing the strain-life fatigue behavior of thin sheet metals is often challenging since the required specimens have short gauge lengths to avoid buckling, thereby preventing the use of conventional mechanical extensometers. To overcome this obstacle a microscopic optical imaging system has been developed to measure the strain amplitude during fatigue testing using Digital Image Correlation (DIC). A strategy for rapidly recording images is utilized to enable sequential image sampling rates of at least 10 frames per second (fps) using a general digital camera. An example of a complete strain-life fatigue test for thin sheet steel under constant displacement control is presented in which the corresponding strain within the gage section of the specimen is measured using the proposed imaging system. The precision in strain measurement is assessed and methods for improving the image sampling rates in dynamic testing are discussed.

Predictive value of the korean academy of family medicine in-training examination for certifying examination.

PubMed

Cho, Jung-Jin; Kim, Ji-Yong

2011-09-01

In-training examination (ITE) is a cognitive examination similar to the written test, but it is different from the Clinical Practice Examination of the Korean Academy of Family Medicine (KAFM) Certification Examination (CE). The objective of this is to estimate the positive predictive value of the KAFM-ITE for identifying residents at risk for poor performance on the three types of KAFM-CE. 372 residents who completed the KAFM-CE in 2011 were included. We compared the mean KAFM-CE scores with ITE experience. We evaluated the correlation and the positive predictive value (PPV) of ITE for the multiple choice question (MCQ) scores of 1st written test & 2nd slide examination, the total clinical practice examination scores, and the total sum of 2nd test. 275 out of 372 residents completed ITE. Those who completed ITE had significantly higher MCQ scores of 1st written test than those who did not. The correlation of ITE scores with 1st written MCQ (0.627) was found to be the highest among the other kinds of CE. The PPV of the ITE score for 1st written MCQ scores was 0.672. The PPV of the ITE score ranged from 0.376 to 0.502. The score of the KAFM ITE has acceptable positive predictive value that could be used as a part of comprehensive evaluation system for residents in cognitive field.

Assessing fundamental 2-dimensional understanding of basic soft tissue techniques.

PubMed

Jabbour, Noel; Dobratz, Eric J; Dresner, Harley S; Hilger, Peter A

2011-01-01

To develop a written practical examination and scoring system for assessing trainee skills in basic soft-tissue techniques. A brief written practical examination was developed to assess the ability of trainees to sketch preoperative plans and postoperative results for common soft-tissue techniques: simple-excision, M-plasty, geometric broken line closure, Z-plasty, V-to-Y flap, and rhombic flap. A scoring system was developed to assign 0 to 5 points to each of 10 items on the examination for a total score of 0-50. The 15-minute examination was administered as a pretest, posttest, and 3-month posttest assessment as part of a soft-tissue course at our institution. University of Minnesota, Otolaryngology Department. Three raters reviewed all examination answer sheets independently. The pretest scores of examinees correlated strongly with their level of training; the average pretest for junior residents (PGY 1-2) compared with senior residents (PGY 4-5) was 17.3 (of 50) versus 26.0 (p < 0.01). The scoring system showed a high intrarater reliability and high interrater reliability with correlation coefficients of r = 0.99 and r = 0.95, respectively and agreement coefficients of κ = 0.82 and κ = 0.77, respectively. This written practical examination and scoring system may be used to assess the skills of trainees accurately in basic soft tissue techniques and to expose areas of deficiency that can be addressed in future training sessions. Copyright © 2011 Association of Program Directors in Surgery. Published by Elsevier Inc. All rights reserved.

A systematic review of interventions to improve recall of medical advice in healthcare consultations.

PubMed

Watson, Philip W B; McKinstry, Brian

2009-06-01

In order for patients to adhere to healthcare advice, it is essential that they are able to recall this following a consultation. Although psychological research exists which highlights techniques and factors postulated to influence recall, only a limited body of work has been conducted to evaluate their effectiveness in a clinical context. To carry out a systematic review of intervention trials designed to enhance recall of medical information. We searched Medline (1950-April 2007); Embase (1980-April 2007); Cinahl (1982-April 2007); PsychINFO (1969-2007); and the Cochrane Library Collection. Secondary searches were made through reference to relevant journals and reference lists from relevant papers/review papers. From 69 papers provisionally identified, 34 papers met the inclusion criteria. Nine recall interventions had been evaluated (audio recordings, written materials, adjunct questions, prompt sheets, visual aids, cognitive strategies, rehearsal, communication styles and personalized teaching). Despite the experimental and theoretical evidence which could have informed cognitive interventions to enhance recall of healthcare advice, most studies primarily focused on the use of written and/or audio-recorded medical instructions. Although the majority of studies supported these approaches insofar as they enhanced recall, the findings were equivocal. While written and tape-recorded instructions appear to improve recall in most situations, a dearth of interventions incorporating psychological theory was readily apparent. Further research is required in clinical settings to determine if cognitive interventions based on a more over-arching psychological model of recall are effective.

Development of a Solar Cell Back Sheet with Excellent UV Durability and Thermal Conductivity.

PubMed

Kang, Seong-Hwan; Choi, Jaeho; Lee, Sung-Ho; Song, Young-Hoon; Park, Jong-Se; Jung, In-Sung; Jung, Jin-Su; Kim, Chong-Yeal; Yang, O-Bong

2018-09-01

The back sheet is one of the most important materials in photovoltaic (PV) modules. It plays an important role in protecting the solar cell from the environment by preventing moisture penetration. In the back sheet, the outermost layer is composed of a polyester (PET) film to protect the PV module from moisture, and the opposite layer is composed of a TiO2 + PE material. Nowadays, PV modules are installed in the desert. Therefore, methods to improve the power generation efficiency of PV modules need to be investigated as the efficiency is affected by temperature resulting from the heat radiation effect. Using a back sheet with a high thermal conductivity, the module output efficiency can be increased as heat is efficiently dissipated. In this study, a thermally conductive film was fabricated by mixing a reference film (TiO2 + PE) and a non-metallic material, MgO, with high thermal conductivity. UV irradiation tests of the film were conducted. The thermally conductive film (TiO2 + PE + MgO) showed higher conductivity than a reference film. No visible cracks and low yellowing degree were found in thermally conductive film, confirming its excellent UV durability characteristics. The sample film was bonded to a PET layer, and a back sheet was fabricated. The yellowing of the back sheet was also analyzed after UV irradiation. In addition, mini modules with four solar cell were fabricated using the developed back sheet, and a comparative outdoor test was conducted. The results showed that power generation improved by 1.38%.

Higher Sensitivity in X-Ray Photography

NASA Technical Reports Server (NTRS)

Buggle, R. N.

1986-01-01

Hidden defects revealed if X-ray energy decreased as exposure progresses. Declining-potential X-ray photography detects fractures in thin metal sheet covered by unbroken sheet of twice thickness. Originally developed to check solder connections on multilayer circuit boards, technique has potential for other nondestructive testing.

An Investigation on Low Velocity Impact Response of Multilayer Sandwich Composite Structures

PubMed Central

Jedari Salami, S.; Sadighi, M.; Shakeri, M.; Moeinfar, M.

2013-01-01

The effects of adding an extra layer within a sandwich panel and two different core types in top and bottom cores on low velocity impact loadings are studied experimentally in this paper. The panel includes polymer composite laminated sheets for faces and the internal laminated sheet called extra layer sheet, and two types of crushable foams are selected as the core material. Low velocity impact tests were carried out by drop hammer testing machine to the clamped multilayer sandwich panels with expanded polypropylene (EPP) and polyurethane rigid (PUR) in the top and bottom cores. Local displacement of the top core, contact force and deflection of the sandwich panel were obtained for different locations of the internal sheet; meanwhile the EPP and PUR were used in the top and bottom cores alternatively. It was found that the core material type has made significant role in improving the sandwich panel's behavior compared with the effect of extra layer location. PMID:24453804

Slicing of Silicon into Sheet Material. Silicon Sheet Growth Development for the Large Area Silicon Sheet Task of the Low Cost Solar Array Project

NASA Technical Reports Server (NTRS)

Fleming, J. R.; Holden, S. C.; Wolfson, R. G.

1979-01-01

The use of multiblade slurry sawing to produce silicon wafers from ingots was investigated. The commercially available state of the art process was improved by 20% in terms of area of silicon wafers produced from an ingot. The process was improved 34% on an experimental basis. Economic analyses presented show that further improvements are necessary to approach the desired wafer costs, mostly reduction in expendable materials costs. Tests which indicate that such reduction is possible are included, although demonstration of such reduction was not completed. A new, large capacity saw was designed and tested. Performance comparable with current equipment (in terms of number of wafers/cm) was demonstrated.

Content Validation of the Comprehension of Written Grammar Assessment for Deaf and Hard of Hearing Students

ERIC Educational Resources Information Center

Cannon, Joanna E.; Hubley, Anita M.

2014-01-01

Content validation is a crucial, but often neglected, component of good test development. In the present study, content validity evidence was collected to determine the degree to which elements (e.g., grammatical structures, items, picture responses, administration, and scoring instructions) of the Comprehension of Written Grammar (CWG) test are…

77 FR 3748 - Request for Comments and Notice of Public Hearings on Genetic Diagnostic Testing

Federal Register 2010, 2011, 2012, 2013, 2014

2012-01-25

...: Written comments should be sent by email to [email protected] . Comments may also be submitted by postal... subject line of the email or postal mailing as ``Genetic Testing Study.'' Because written comments and... wishing to present oral testimony at either hearing must request an opportunity to do so in writing no...

Preliminary Investigation of Impact on Multiple-Sheet Structures and an Evaluation of the Meteoroid Hazard to Space Vehicles

NASA Technical Reports Server (NTRS)

Nysmith, C. Robert; Summers, James L.

1961-01-01

Small pyrex glass spheres, representative of stoney meteoroids, were fired into 2024-T3 aluminum alclad multiple-sheet structures at velocities to 11,000 feet per second to evaluate the effectiveness of multisheet hull construction as a means of increasing the resistance of a spacecraft to meteoroid penetrations. The results of these tests indicate that increasing the number of sheets in a structure while keeping the total sheet thickness constant and increasing the spacing between sheets both tend to increase the penetration resistance of a structure of constant weight per unit area. In addition, filling the space between the sheets with a light filler material was found to substantially increase structure penetration resistance with a small increase in weight. An evaluation of the meteoroid hazard to space vehicles is presented in the form of an illustrative-example for two specific lunar mission vehicles, a single-sheet, monocoque hull vehicle and a glass-wool filled, double-sheet hull vehicle. The evaluation is presented in terms of the "best" and the "worst" conditions that might be expected as determined from astronomical and satellite measurements, high-speed impact data, and hypothesized meteoroid structures and compositions. It was observed that the vehicle flight time without penetration can be increased significantly by use of multiple-sheet rather than single-sheet hull construction with no increase in hull weight. Nevertheless, it is evident that a meteoroid hazard exists, even for the vehicle with the selected multiple-sheet hull.

A Comparison of the Performance of Graduate and Undergraduate School Applicants on the Test of Written English. TOEFL Research Reports Report 50.

ERIC Educational Resources Information Center

Zwick, Rebecca; Thayer, Dorothy T.

The performance of graduate and undergraduate school applicants on the Test of Written English (TWE) was compared for each of 66 data sets, dating from 1988 to 1993. The analyses compared the average TWE score for graduates and undergraduates after matching examinees on the total score on the Test of English as a Foreign Language (TOEFL). The main…

Topical Application of a Silicone Gel Sheet with Verapamil Microparticles in a Rabbit Model of Hypertrophic Scar.

PubMed

Rha, Eun Young; Kim, Yun Ho; Kim, Tae-Jung; Yoo, Gyeol; Rhie, Jong Won; Kim, Hyun-Jung; Park, Il-Kyu

2016-01-01

The authors developed a novel treatment based on the topical application of a silicone gel sheet containing verapamil microparticles. The ability of these silicone gel sheets to inhibit hypertrophic scar in a rabbit ear wound model was examined. Ten New Zealand White rabbits with a total of 80 wounds in both ears were used in this study. The rabbits were divided into five groups (control; silicone gel sheet; and silicone gel sheet plus 0.25, 2.5, and 25 mg of verapamil per gram). Histopathologic findings were quantified. The mean scar elevation index, fibroblast counts, and capillary counts differed significantly among the five groups (p < 0.05). The median scar elevation index was significantly lower in the silicone gel sheet plus 2.5 mg of verapamil per gram group than in the silicone gel sheet group (1.2 versus 2.2). The median number of fibroblasts was significantly lower in the silicone gel sheet plus 0.25 mg of verapamil per gram group than in the silicone gel sheet group (172.5 versus 243). In the median number of capillary lumina, there was no significant difference between the silicone gel sheet group and the silicone gel sheet plus 0.25, 2.5, and 25 mg of verapamil per gram groups (28.5, 18, 20, and 18, respectively). Topical application of a silicone gel sheet with verapamil microparticles may be a novel, effective treatment method for hypertrophic scar, but its safety and efficacy in humans must be tested in clinical trials.

Sheet Membrane Spacesuit Water Membrane Evaporator

NASA Technical Reports Server (NTRS)

Bue, Grant; Trevino, Luis; Zapata, Felipe; Dillion, Paul; Castillo, Juan; Vonau, Walter; Wilkes, Robert; Vogel, Matthew; Frodge, Curtis

2013-01-01

A document describes a sheet membrane spacesuit water membrane evaporator (SWME), which allows for the use of one common water tank that can supply cooling water to the astronaut and to the evaporator. Test data showed that heat rejection performance dropped only 6 percent after being subjected to highly contaminated water. It also exhibited robustness with respect to freezing and Martian atmospheric simulation testing. Water was allowed to freeze in the water channels during testing that simulated a water loop failure and vapor backpressure valve failure. Upon closing the backpressure valve and energizing the pump, the ice eventually thawed and water began to flow with no apparent damage to the sheet membrane. The membrane evaporator also serves to de-gas the water loop from entrained gases, thereby eliminating the need for special degassing equipment such as is needed by the current spacesuit system. As water flows through the three annular water channels, water evaporates with the vapor flowing across the hydrophobic, porous sheet membrane to the vacuum side of the membrane. The rate at which water evaporates, and therefore, the rate at which the flowing water is cooled, is a function of the difference between the water saturation pressure on the water side of the membrane, and the pressure on the vacuum side of the membrane. The primary theory is that the hydrophobic sheet membrane retains water, but permits vapor pass-through when the vapor side pressure is less than the water saturation pressure. This results in evaporative cooling of the remaining water.

Bond–Slip Relationship for CFRP Sheets Externally Bonded to Concrete under Cyclic Loading

PubMed Central

Li, Ke; Cao, Shuangyin; Yang, Yue; Zhu, Juntao

2018-01-01

The objective of this paper was to explore the bond–slip relationship between carbon fiber-reinforced polymer (CFRP) sheets and concrete under cyclic loading through experimental and analytical approaches. Modified beam tests were performed in order to gain insight into the bond–slip relationship under static and cyclic loading. The test variables are the CFRP-to-concrete width ratio, and the bond length of the CFRP sheets. An analysis of the test results in this paper and existing test results indicated that the slope of the ascending segment of the bond–slip curve decreased with an increase in the number of load cycles, but the slip corresponding to the maximum shear stress was almost invariable as the number of load cycles increased. In addition, the rate of reduction in the slope of the ascending range of the bond–slip curve during cyclic loading decreased as the concrete strength increased, and increased as the load level or CFRP-to-concrete width ratio enhanced. However, these were not affected by variations in bond length if the residual bond length was longer than the effective bond length. A bilinear bond–slip model for CFRP sheets that are externally bonded to concrete under cyclic loading, which considered the effects of the cyclic load level, concrete strength, and CFRP-to-concrete ratio, was developed based on the existing static bond–slip model. The accuracy of this proposed model was verified by a comparison between this proposed model and test results. PMID:29495383

Bond-Slip Relationship for CFRP Sheets Externally Bonded to Concrete under Cyclic Loading.

PubMed

Li, Ke; Cao, Shuangyin; Yang, Yue; Zhu, Juntao

2018-02-26

The objective of this paper was to explore the bond-slip relationship between carbon fiber-reinforced polymer (CFRP) sheets and concrete under cyclic loading through experimental and analytical approaches. Modified beam tests were performed in order to gain insight into the bond-slip relationship under static and cyclic loading. The test variables are the CFRP-to-concrete width ratio, and the bond length of the CFRP sheets. An analysis of the test results in this paper and existing test results indicated that the slope of the ascending segment of the bond-slip curve decreased with an increase in the number of load cycles, but the slip corresponding to the maximum shear stress was almost invariable as the number of load cycles increased. In addition, the rate of reduction in the slope of the ascending range of the bond-slip curve during cyclic loading decreased as the concrete strength increased, and increased as the load level or CFRP-to-concrete width ratio enhanced. However, these were not affected by variations in bond length if the residual bond length was longer than the effective bond length. A bilinear bond-slip model for CFRP sheets that are externally bonded to concrete under cyclic loading, which considered the effects of the cyclic load level, concrete strength, and CFRP-to-concrete ratio, was developed based on the existing static bond-slip model. The accuracy of this proposed model was verified by a comparison between this proposed model and test results.

[Leonardo da Vinci and his studies on the human fetus and the placenta].

PubMed

Cataldi, L; Fanos, V

2000-01-01

To review the accuracy of Leonardo's anatomical studies of the female external genitalia and the foetus, particularly those concerning the umbilical cord with its blood vessels. The anatomical drawings of Leonardo da Vinci which are now stored in the Windors Castle near London were reviewed and the accuracy of the details of the genital apparatus and foetus was evaluated. A written comment characterizes many of his drawings. He described accurately the position of the uterine blood vessels and the relationship between the pelvic organs. However his drawing and description of the female external genitalia and human placenta was incorrect because his understanding of it was inadequate. He believed that the human placenta had cotyledons like that of the ungulate uterus (drown side A of sheet 19). At the top of that sheet some Leonardo's details of the anatomic relationship are shown. In our opinion, Leonardo's misunderstanding is probably because he was only able to perform one anatomical dissection of a pregnant women and foetus and therefore his knowledge was limited. The resulting documentation of the pregnant women and foetus was therefore heavily supplemented with his enormous experience in animal anatomy.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Rubing, E-mail: zrb86411680@126.com; Zhang, Yaoyao; Liu, Qiang

TiAl/Nb and TiAl/NiCoCrAl laminate composite sheets with a thickness of 0.4–0.6 mm and dimensions of 150 mm × 100 mm were successfully fabricated by electron beam physical vapor deposition. The microstructures of the sheets were examined, and their mechanical properties were compared with those of TiAl monolithic sheet produced by electron beam physical vapor deposition. Tensile testing was performed at room temperature and 750 °C, and the fracture surfaces were examined by scanning electron microscopy. Among the three microlaminate sheets, the TiAl/NiCoCrAl micro-laminate sheet had the best comprehensive properties at room temperature, and the TiAl/Nb micro-laminate sheet showed the idealmore » high-temperature strength and plasticity at 750 °C. The result was discussed in terms of metal strengthening mechanism. - Highlights: • TiAl-based multilayer foils was fabricated successfully by using EB-PVD method; • The tensile properties and micro-fracture morphologies of the sheet were investigated; • The deformation behavior of the multilayer foils was discussed.« less

Dynamics of a radially expanding liquid sheet: Experiments

NASA Astrophysics Data System (ADS)

Majumdar, Nayanika; Tirumkudulu, Mahesh

2017-11-01

A recent theory predicts that sinuous waves generated at the center of a radially expanding liquid sheet grow spatially even in absence of a surrounding gas phase. Unlike flat liquid sheets, the thickness of a radially expanding liquid sheet varies inversely with distance from the center of the sheet. To test the predictions of the theory, experiments were carried out on a horizontal, radially expanding liquid sheet formed by collision of a single jet on a solid impactor. The latter was placed on a speaker-vibrator with controlled amplitude and frequency. The growth of sinuous waves was determined by measuring the wave surface inclination angle using reflected laser light under both atmospheric and sub-atmospheric pressure conditions. It is shown that the measured growth rate matches with the predictions of the theory over a large range of Weber numbers for both pressure conditions suggesting that the thinning of the liquid sheet plays a dominant role in setting the growth rate of sinuous waves with minimal influence of the surrounding gas phase on its dynamics. IIT Bombay.

Bending Tests of Circular Cylinders of Corrugated Aluminum-alloy Sheet

NASA Technical Reports Server (NTRS)

Buckwalter, John C; Reed, Warren D; Niles, Alfred S

1937-01-01

Bending tests were made of two circular cylinders of corrugated aluminum-alloy sheet. In each test failure occurred by bending of the corrugations in a plane normal to the skin. It was found, after analysis of the effect of short end bays, that the computed stress on the extreme fiber of a corrugated cylinder is in excess of that for a flat panel of the same basic pattern and panel length tested as a pin-ended column. It is concluded that this increased strength was due to the effects of curvature of the pitch line. It is also concluded from the tests that light bulkheads closely spaced strengthen corrugated cylinders very materially.

Executive functions in becoming writing readers and reading writers: note taking and report writing in third and fifth graders.

PubMed

Altemeier, Leah; Jones, Janine; Abbott, Robert D; Berninger, Virginia W

2006-01-01

Results are reported for a study of 2 separate processes of report writing-taking notes while reading source material and composing a report from those notes-and related individual differences in executive functions involved in integrating reading and writing during these writing activities. Third graders (n = 122) and 5th graders (n = 106; overall, 127 girls and 114 boys) completed two reading-writing tasks-read paragraph (mock science text)-write notes and use notes to generate written report, a reading comprehension test, a written expression test, four tests of executive functions (inhibition, verbal fluency, planning, switching attention), and a working memory test. For the read-take notes task, the same combination of variables was best (explained the most variance and each variable added unique variance) for 3rd graders and 5th graders: Wechsler Individual Achievement Test-Second Edition (WIAT-II) Reading Comprehension, Process Assessment of the Learner Test for Reading and Writing (PAL) Copy Task B, WIAT-II Written Expression, and Delis-Kaplan Executive Function System (D-KEFS) Inhibition. For the use notes to write report task, the best combinations of variables depended on grade level: For 3rd graders, WIAT-II Reading Comprehension, WIAT-II Written Expression, D-KEFS Verbal Fluency, and Tower of Hanoi; for 5th graders, WIAT-II Reading Comprehension, D-KEFS Verbal Fluency, WIAT-II Written Expression, and PAL Alphabet Task. These results add to prior research findings that executive functions contribute to the writing development of elementary-grade students and additionally support the hypothesis that executive functions play a role in developing reading-writing connections.

Application of image processing technology to problems in manuscript encapsulation. [Codex Hammer

NASA Technical Reports Server (NTRS)

Glackin, D. L.; Korsmo, E. P.

1983-01-01

The long term effects of encapsulation individual sheets of the Codex Hammer were investigated. The manuscript was simulated with similar sheets of paper which were photographed under repeatable raking light conditions to enhance their surface texture, encapsulated in plexiglas, cycled in an environmental test chamber, and rephotographed at selected intervals. The film images were digitized, contrast enhanced, geometrically registered, and apodized. An FFT analysis of a control sheet and two experimental sheets indicates no micro-burnishing, but reveals that the ""mesoscale'' deformations with sizes 8mm are degrading monotonically, which is of no concern. Difference image analysis indicates that the sheets were increasingly stressed with time and that the plexiglas did not provide a sufficient environmental barrier under the simulation conditions. The relationship of these results to the Codex itself is to be determined.

Lateral dimension-dependent antibacterial activity of graphene oxide sheets.

PubMed

Liu, Shaobin; Hu, Ming; Zeng, Tingying Helen; Wu, Ran; Jiang, Rongrong; Wei, Jun; Wang, Liang; Kong, Jing; Chen, Yuan

2012-08-21

Graphene oxide (GO) is a promising precursor to produce graphene-family nanomaterials for various applications. Their potential health and environmental impacts need a good understanding of their cellular interactions. Many factors may influence their biological interactions with cells, and the lateral dimension of GO sheets is one of the most relevant material properties. In this study, a model bacterium, Escherichia coli ( E. coli ), was used to evaluate the antibacterial activity of well-dispersed GO sheets, whose lateral size differs by more than 100 times. Our results show that the antibacterial activity of GO sheets toward E. coli cells is lateral size dependent. Larger GO sheets show stronger antibacterial activity than do smaller ones, and they have different time- and concentration-dependent antibacterial activities. Large GO sheets lead to most cell loss after 1 h incubation, and their concentration strongly influences antibacterial activity at relative low concentration (<10 μg/mL). In contrast, when incubating with small GO sheets up to 4 h, the inactivation rate of E. coli cells continues increasing. The increase of small GO sheet concentration also results in persistent increases in their antibacterial activity. In this study, GO sheets with different lateral sizes are all well dispersed, and their oxidation capacity toward glutathione is similar, consistent with X-ray photoelectron spectroscopy and ultraviolet-visible absorption spectroscopy results. This suggests the lateral size-dependent antibacterial activity of GO sheets is caused by neither their aggregation states, nor oxidation capacity. Atomic force microscope analysis of GO sheets and cells shows that GO sheets interact strongly with cells. Large GO sheets more easily cover cells, and cells cannot proliferate once fully covered, resulting in the cell viability loss observed in the followed colony counting test. In contrast, small GO sheets adhere to the bacterial surfaces, which cannot effectively isolate cells from environment. This study highlights the importance of tailoring the lateral dimension of GO sheets to optimize the application potential with minimal risks for environmental health and safety.

The Impact of Executive Functions on the Written Language Process: Some Evidence from Children with Writing Disabilities

ERIC Educational Resources Information Center

Alevriadou, Anastasia; Giaouri, Stergiani

2015-01-01

Written language is a difficult endeavour as the demands of transcription require self-regulatory skills from a motor, cognitive and attention perspective. The purpose of the present study was to investigate the relation between the Test of Writing Difficulties (Porpodas et al., 2007) and the Test of Detection and Investigation of Executive…

Follicular contact dermatitis due to coloured permanent-pressed sheets

PubMed Central

Panaccio, François; Montgomery, D. C.; Adam, J. E.

1973-01-01

A delayed hypersensitivity type of allergic contact dermatitis was observed following exposure to certain brands of 50% cotton, 50% polyester coloured permanent-pressed sheets produced by a particular manufacturer. The dermatitis presented as an extremely pruritic follicular eczema of the body and vesicular edema of the ears and face. Patch testing excluded formalin as the allergen but suggested permanent-pressing chemicals as a possibility. Several washings of the sheets did not prevent the development of the dermatitis. The removal of sheets did not immediately result in improvement: the condition could persist for up to eight weeks after their discontinuance. ImagesFIG. 1FIG. 2FIG. 3FIG. 4FIG. 5 PMID:4268628

Self-consistent current sheet structures in the quiet-time magnetotail

NASA Technical Reports Server (NTRS)

Holland, Daniel L.; Chen, James

1993-01-01

The structure of the quiet-time magnetotail is studied using a test particle simulation. Vlasov equilibria are obtained in the regime where v(D) = E(y) c/B(z) is much less than the ion thermal velocity and are self-consistent in that the current and magnetic field satisfy Ampere's law. Force balance between the plasma and magnetic field is satisfied everywhere. The global structure of the current sheet is found to be critically dependent on the source distribution function. The pressure tensor is nondiagonal in the current sheet with anisotropic temperature. A kinetic mechanism is proposed whereby changes in the source distribution results in a thinning of the current sheet.

Boron supercapacitors

DOE PAGES

Zhan, Cheng; Zhang, Pengfei; Dai, Sheng; ...

2016-11-16

Supercapacitors based on the electric double-layer mechanism use porous carbons or graphene as electrodes. To move beyond this paradigm, we propose boron supercapacitors to leverage two-dimensional (2D) boron sheets’ metallicity and low weight. Six 2D boron sheets from both previous theoretical design and experimental growth are chosen as test electrodes. By applying joint density functional theory (JDFT) to the electrode–electrolyte system, we examine how the 2D boron sheets charge up against applied potential. JDFT predicts that these 2D boron sheets exhibit specific capacitance on the order of 400 F/g, about four times that of graphene. As a result, our workmore » suggests that 2D boron sheets are promising electrodes for supercapacitor applications.« less

Boron supercapacitors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhan, Cheng; Zhang, Pengfei; Dai, Sheng

Supercapacitors based on the electric double-layer mechanism use porous carbons or graphene as electrodes. To move beyond this paradigm, we propose boron supercapacitors to leverage two-dimensional (2D) boron sheets’ metallicity and low weight. Six 2D boron sheets from both previous theoretical design and experimental growth are chosen as test electrodes. By applying joint density functional theory (JDFT) to the electrode–electrolyte system, we examine how the 2D boron sheets charge up against applied potential. JDFT predicts that these 2D boron sheets exhibit specific capacitance on the order of 400 F/g, about four times that of graphene. As a result, our workmore » suggests that 2D boron sheets are promising electrodes for supercapacitor applications.« less

[Care and optimal management of the face- and neck-lift patients].

PubMed

Delay, E

2017-10-01

Surgical and case management for patients demanding a face- and neck-lift are very important. The purpose of this paper is to help the plastic surgeons with information and recommendations useful for the best medical care of patients requiring a face- and neck-lift. The first consultation is the most important contact with the patient. The preoperative discussion helps to define patient demands and to evaluate eventual contraindications for surgery. The clinical exam and patient requirements are useful in the construction of the therapeutic proposition. This proposition is then confronted with patients' expectations and demands. The confrontation between the surgical proposition and patients' expectations allows to evaluate if it is appropriate, or not, to operate. At the end of the first consultation, the patient receives the information sheets of the French Plastic Surgery Society (SOFCPRE) according to the proposed surgical treatment. The second consultation makes it possible to verify the pertinence of the surgical act, to reiterate the preoperative recommendations, to confirm that the information given to the patient was well understood and to obtain the written consent from the patient. The written consent should include the fact that the patient received the information sheets of the SOFCPRE, that they were read and understood, and that the surgeon has transmitted the necessary information in order for the patient to take an informed and free decision to pursue with the surgery. The follow-up after surgery is as important as the surgery itself. In some cases, cosmetic gestures can be performed in the following months to obtain the best results possible and the highest satisfaction. The face- and neck-lift is an "adventure" for the patients and the postoperative difficulties should not be underestimated. However, the caring and professional support of the plastic surgeon and the support of someone of the patients' entourage can help the patient overcome this stage, and obtain a maximum benefit after this operation. Copyright © 2017 Elsevier Masson SAS. All rights reserved.

Drilling Machines: Vocational Machine Shop.

ERIC Educational Resources Information Center

Thomas, John C.

The lessons and supportive information in this field tested instructional block provide a guide for teachers in developing a machine shop course of study in drilling. The document is comprised of operation sheets, information sheets, and transparency masters for 23 lessons. Each lesson plan includes a performance objective, material and tools,…

LOFT. Containment and service building (TAN650). Room number schedule, sheet ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

LOFT. Containment and service building (TAN-650). Room number schedule, sheet 2 of 2. Kaiser engineers 6413-11-STEP/LOFT-650-A-XX. Date: October 1969. INEEL index code no. 036-650-00-486-122228 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

Static renewal tests using Anodonta imbecillis (freshwater mussels). Anodonta imbecillis QA test 4, Clinch River-Environmental Restoration Program (CR-ERP)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Simbeck, D.J.

1994-12-31

Toxicity testing of split whole sediment samples using juvenile freshwater mussels (Anodonta imbecillis) was conducted by TVA to provide a quality assurance mechanism for test organisms quality and overall performance of the test being conducted by CR-ERP personnel as part of the CR-ERP biomonitoring study of Clinch River sediments. Testing of sediment samples collected September 8 from Poplar Creek Miles 6.0 and 1.0 was conducted September 13--22, 1994. Results from this test showed no toxicity (survival effects) to fresh-water mussels during a 9-day exposure to the sediments. Attachments to this report include: Chain of custody form -- original; Toxicity testmore » bench sheets; Ammonia analysis request and results; and Meter calibration log sheets.« less

Predictive Value of the Korean Academy of Family Medicine In-Training Examination for Certifying Examination

PubMed Central

Kim, Ji-Yong

2011-01-01

Background In-training examination (ITE) is a cognitive examination similar to the written test, but it is different from the Clinical Practice Examination of the Korean Academy of Family Medicine (KAFM) Certification Examination (CE). The objective of this is to estimate the positive predictive value of the KAFM-ITE for identifying residents at risk for poor performance on the three types of KAFM-CE. Methods 372 residents who completed the KAFM-CE in 2011 were included. We compared the mean KAFM-CE scores with ITE experience. We evaluated the correlation and the positive predictive value (PPV) of ITE for the multiple choice question (MCQ) scores of 1st written test & 2nd slide examination, the total clinical practice examination scores, and the total sum of 2nd test. Results 275 out of 372 residents completed ITE. Those who completed ITE had significantly higher MCQ scores of 1st written test than those who did not. The correlation of ITE scores with 1st written MCQ (0.627) was found to be the highest among the other kinds of CE. The PPV of the ITE score for 1st written MCQ scores was 0.672. The PPV of the ITE score ranged from 0.376 to 0.502. Conclusion The score of the KAFM ITE has acceptable positive predictive value that could be used as a part of comprehensive evaluation system for residents in cognitive field. PMID:22745873

Effects of structured versus non-structured learning on achievement and attitudes of fifth graders in a public aquarium

NASA Astrophysics Data System (ADS)

Kafka, Merryl Audrey

The investigator analyzed the main effect of a structured-learning experience in an informal setting, as well as interactions between the students' learning-style variations toward the element of structure and the imposed instructional conditions. The subjects consisted of 170 students enrolled in two public schools located in Brooklyn, New York. The students were predominantly a White multi-ethnic population consisting of 118 Caucasians, 25 Hispanics, 24 Asians, and 3 African-Americans. Three randomly assigned classes (n = 81) were provided trip sheets, which directed students on how to learn new information with written questions and directives. Three randomly assigned non-structured classes (n = 89) experienced the same exhibit in a free-form manner. Science-based criterion-referenced pre- and posttests were administered, in addition to Learning Style Inventories (Dunn, Dunn, & Price, 1996) and a modified Semantic Differential Scale (Pizzo, 1981), which was used to measure attitudinal levels. The non-structured group had access to similar content information in the form of exhibit graphics, but apparently they chose not to read it as carefully or engage in the information-seeking process as intensely as the students equipped with trip sheets. Analysis of covariance (ANCOVA) indicated that a structured-learning experience produced significantly higher science-achievement test scores than in a non-structured-learning experience (p = .0001). In addition, there was no single learning-style variation (preference, aversion, or no preference) to structure that produced significantly higher gains than another. Furthermore, attitudinal scores were not significantly different between structured and non-structured groups, as well as among homogeneous subsets of students with learning-style variations that matched, mismatched, or indicated no-preferenced positions on the element of structure. Hence, a moderate amount of structure resulted in academic gains without diminishing attitudinal scores. The fact that students' learning-style variations for sociological, design, and perceptual preferences were simultaneously accommodated in this setting may have contributed to the overall positive effects of this structure-based intervention. The diversified teaching resources of the exhibit and the sense of self-empowerment in a student-directed environment may have elevated students' attitudes regardless of their learning-style need for structure. The students' acceptance of a trip sheet that promoted the understanding of science concepts may have contributed to academic success.

Packing and deploying Soft Origami to and from cylindrical volumes with application to automotive airbags

PubMed Central

Nelson, Todd G.; Zimmerman, Trent K.; Fernelius, Janette D.; Magleby, Spencer P.; Howell, Larry L.

2016-01-01

Packing soft-sheet materials of approximately zero bending stiffness using Soft Origami (origami patterns applied to soft-sheet materials) into cylindrical volumes and their deployment via mechanisms or internal pressure (inflation) is of interest in fields including automobile airbags, deployable heart stents, inflatable space habitats, and dirigible and parachute packing. This paper explores twofold patterns, the ‘flasher’ and the ‘inverted-cone fold’, for packing soft-sheet materials into cylindrical volumes. Two initial packing methods and mechanisms are examined for each of the flasher and inverted-cone fold patterns. An application to driver’s side automobile airbags is performed, and deployment tests are completed to compare the influence of packing method and origami pattern on deployment performance. Following deployment tests, two additional packing methods for the inverted-cone fold pattern are explored and applied to automobile airbags. It is shown that modifying the packing method (using different methods to impose the same base pattern on the soft-sheet material) can lead to different deployment performance. In total, two origami patterns and six packing methods are examined, and the benefits of using Soft Origami patterns and packing methods are discussed. Soft Origami is presented as a viable method for efficiently packing soft-sheet materials into cylindrical volumes. PMID:27703707

Packing and deploying Soft Origami to and from cylindrical volumes with application to automotive airbags

NASA Astrophysics Data System (ADS)

Bruton, Jared T.; Nelson, Todd G.; Zimmerman, Trent K.; Fernelius, Janette D.; Magleby, Spencer P.; Howell, Larry L.

2016-09-01

Packing soft-sheet materials of approximately zero bending stiffness using Soft Origami (origami patterns applied to soft-sheet materials) into cylindrical volumes and their deployment via mechanisms or internal pressure (inflation) is of interest in fields including automobile airbags, deployable heart stents, inflatable space habitats, and dirigible and parachute packing. This paper explores twofold patterns, the `flasher' and the `inverted-cone fold', for packing soft-sheet materials into cylindrical volumes. Two initial packing methods and mechanisms are examined for each of the flasher and inverted-cone fold patterns. An application to driver's side automobile airbags is performed, and deployment tests are completed to compare the influence of packing method and origami pattern on deployment performance. Following deployment tests, two additional packing methods for the inverted-cone fold pattern are explored and applied to automobile airbags. It is shown that modifying the packing method (using different methods to impose the same base pattern on the soft-sheet material) can lead to different deployment performance. In total, two origami patterns and six packing methods are examined, and the benefits of using Soft Origami patterns and packing methods are discussed. Soft Origami is presented as a viable method for efficiently packing soft-sheet materials into cylindrical volumes.

Packing and deploying Soft Origami to and from cylindrical volumes with application to automotive airbags.

PubMed

Bruton, Jared T; Nelson, Todd G; Zimmerman, Trent K; Fernelius, Janette D; Magleby, Spencer P; Howell, Larry L

2016-09-01

Packing soft-sheet materials of approximately zero bending stiffness using Soft Origami (origami patterns applied to soft-sheet materials) into cylindrical volumes and their deployment via mechanisms or internal pressure (inflation) is of interest in fields including automobile airbags, deployable heart stents, inflatable space habitats, and dirigible and parachute packing. This paper explores twofold patterns, the 'flasher' and the 'inverted-cone fold', for packing soft-sheet materials into cylindrical volumes. Two initial packing methods and mechanisms are examined for each of the flasher and inverted-cone fold patterns. An application to driver's side automobile airbags is performed, and deployment tests are completed to compare the influence of packing method and origami pattern on deployment performance. Following deployment tests, two additional packing methods for the inverted-cone fold pattern are explored and applied to automobile airbags. It is shown that modifying the packing method (using different methods to impose the same base pattern on the soft-sheet material) can lead to different deployment performance. In total, two origami patterns and six packing methods are examined, and the benefits of using Soft Origami patterns and packing methods are discussed. Soft Origami is presented as a viable method for efficiently packing soft-sheet materials into cylindrical volumes.

Experimental characterization and macro-modeling of mechanical strength of multi-sheets and multi-materials spot welds under pure and mixed modes I and II

NASA Astrophysics Data System (ADS)

Chtourou, Rim; Haugou, Gregory; Leconte, Nicolas; Zouari, Bassem; Chaari, Fahmi; Markiewicz, Eric

2015-09-01

Resistance Spot Welding (RSW) of multiple sheets with multiple materials are increasingly realized in the automotive industry. The mechanical strength of such new generation of spot welded assemblies is not that much dealt with. This is true in particular for experiments dedicated to investigate the mechanical strength of spot weld made by multi sheets of different grades, and their macro modeling in structural computations. Indeed, the most published studies are limited to two sheet assemblies. Therefore, in the first part of this work an advanced experimental set-up with a reduced mass is proposed to characterize the quasi-static and dynamic mechanical behavior and rupture of spot weld made by several sheets of different grades. The proposed device is based on Arcan test, the plates contribution in the global response is, thus, reduced. Loading modes I/II are, therefore, combined and well controlled. In the second part a simplified spot weld connector element (macroscopic modeling) is proposed to describe the nonlinear response and rupture of this new generation of spot welded assemblies. The weld connector model involves several parameters to be set. The remaining parameters are finally identified through a reverse engineering approach using mechanical responses of experimental tests presented in the first part of this work.

Testing of Shelter Design and Industrial Hardening Concepts at the MILL RACE Event.

DTIC Science & Technology

1982-01-01

built. The upgrading consisted of the application of 2-in. thick sheets of expanded polystyrene to the exterior of each of the test walls to be upgraded...was covered with 1-in. thick sheets of expanded polystyrene prior to backfilling (Figure 6-4), and the interior was shored, floor to ceiling, with two...deformations in the vault, despite the fact that no structural upgrading options (shores, or roof cover of expanded polystyrene ) were installed. Thus

10. Photographic copy of engineering drawing showing the plumbing layout ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

10. Photographic copy of engineering drawing showing the plumbing layout of Test Stand 'C' Cv Cell, vacuum line, and scrubber-condenser as erected in 1977-78. JPL drawing by VTN Consolidated, Inc. Engineers, Architects, Planners, 2301 Campus Drive, Irvine, California 92664: 'JPL-ETS E-18 (C-Stand Modifications) Flow Diagram,' sheet M-2 (JPL sheet number E18/41-0), September 1, 1977. - Jet Propulsion Laboratory Edwards Facility, Test Stand C, Edwards Air Force Base, Boron, Kern County, CA

9. Photographic copy of engineering drawing showing the mechanical layout ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

9. Photographic copy of engineering drawing showing the mechanical layout of Test Stand 'C' Cv Cell, vacuum line, and scrubber-condenser as erected in 1977-78. JPL drawing by VTN Consolidated, Inc. Engineers, Architects, Planners, 2301 Campus Drive, Irvine, California 92664: 'JPL-ETS E-18 (C-Stand Modifications) Control Elevations & Schematics,' sheet M-5 (JPL sheet number E18/44-0), 1 September 1977. - Jet Propulsion Laboratory Edwards Facility, Test Stand C, Edwards Air Force Base, Boron, Kern County, CA

Biomimetic collagen/elastin meshes for ventral hernia repair in a rat model.

PubMed

Minardi, Silvia; Taraballi, Francesca; Wang, Xin; Cabrera, Fernando J; Van Eps, Jeffrey L; Robbins, Andrew B; Sandri, Monica; Moreno, Michael R; Weiner, Bradley K; Tasciotti, Ennio

2017-03-01

Ventral hernia repair remains a major clinical need. Herein, we formulated a type I collagen/elastin crosslinked blend (CollE) for the fabrication of biomimetic meshes for ventral hernia repair. To evaluate the effect of architecture on the performance of the implants, CollE was formulated both as flat sheets (CollE Sheets) and porous scaffolds (CollE Scaffolds). The morphology, hydrophylicity and in vitro degradation were assessed by SEM, water contact angle and differential scanning calorimetry, respectively. The stiffness of the meshes was determined using a constant stretch rate uniaxial tensile test, and compared to that of native tissue. CollE Sheets and Scaffolds were tested in vitro with human bone marrow-derived mesenchymal stem cells (h-BM-MSC), and finally implanted in a rat ventral hernia model. Neovascularization and tissue regeneration within the implants was evaluated at 6weeks, by histology, immunofluorescence, and q-PCR. It was found that CollE Sheets and Scaffolds were not only biomechanically sturdy enough to provide immediate repair of the hernia defect, but also promoted tissue restoration in only 6weeks. In fact, the presence of elastin enhanced the neovascularization in both sheets and scaffolds. Overall, CollE Scaffolds displayed mechanical properties more closely resembling those of native tissue, and induced higher gene expression of the entire marker genes tested, associated with de novo matrix deposition, angiogenesis, adipogenesis and skeletal muscles, compared to CollE Sheets. Altogether, this data suggests that the improved mechanical properties and bioactivity of CollE Sheets and Scaffolds make them valuable candidates for applications of ventral hernia repair. Due to the elevated annual number of ventral hernia repair in the US, the lack of successful grafts, the design of innovative biomimetic meshes has become a prime focus in tissue engineering, to promote the repair of the abdominal wall, avoid recurrence. Our meshes (CollE Sheets and Scaffolds) not only showed promising mechanical performance, but also allowed for an efficient neovascularization, resulting in new adipose and muscle tissue formation within the implant, in only 6weeks. In addition, our meshes allowed for the use of the same surgical procedure utilized in clinical practice, with the commercially available grafts. This study represents a significant step in the design of bioactive acellular off-the-shelf biomimetic meshes for ventral hernia repair. Copyright © 2016 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Sea-level response to abrupt ocean warming of Antarctic ice shelves

NASA Astrophysics Data System (ADS)

Pattyn, Frank

2016-04-01

Antarctica's contribution to global sea-level rise increases steadily. A fundamental question remains whether the ice discharge will lead to marine ice sheet instability (MISI) and collapse of certain sectors of the ice sheet or whether ice loss will increase linearly with the warming trends. Therefore, we employ a newly developed ice sheet model of the Antarctic ice sheet, called f.ETISh (fast Elementary Thermomechanical Ice Sheet model) to simulate ice sheet response to abrupt perturbations in ocean and atmospheric temperature. The f.ETISh model is a vertically integrated hybrid (SSA/SIA) ice sheet model including ice shelves. Although vertically integrated, thermomechanical coupling is ensured through a simplified representation of ice sheet thermodynamics based on an analytical solution of the vertical temperature profile, including strain heating and horizontal advection. The marine boundary is represented by a flux condition either coherent with power-law basal sliding (Pollard & Deconto (2012) based on Schoof (2007)) or according to Coulomb basal friction (Tsai et al., 2015), both taking into account ice-shelf buttressing. Model initialization is based on optimization of the basal friction field. Besides the traditional MISMIP tests, new tests with respect to MISI in plan-view models have been devised. The model is forced with stepwise ocean and atmosphere temperature perturbations. The former is based on a parametrised sub-shelf melt (limited to ice shelves), while the latter is based on present-day mass balance/surface temperature and corrected for elevation changes. Surface melting is introduced using a PDD model. Results show a general linear response in mass loss to ocean warming. Nonlinear response due to MISI occurs under specific conditions and is highly sensitive to the basal conditions near the grounding line, governed by both the initial conditions and the basal sliding/deformation model. The Coulomb friction model leads to significantly higher sensitivity compared to power-law sliding. On longer time scales, West-antarctic inter-basin connections favor nonlinear response.

Pilot randomized trial of a volitional help sheet-based tool to increase leisure time physical activity in breast cancer survivors.

PubMed

Chapman, Janine; Fletcher, Chloe; Flight, Ingrid; Wilson, Carlene

2018-05-16

To develop and test a volitional help sheet-based tool to improve physical activity in breast cancer survivors compared to a standard self-generated implementation intention intervention. Pilot randomized trial conducted online over 3 months. Participants were randomized to an online volitional help sheet (n = 50) or implementation intention (n = 51) intervention. Measures were taken at baseline, 1 and 3 months. The main outcome measure was moderate-strenuous leisure time physical activity. Secondary outcomes were health-related quality of life and mood. Participants exposed to the volitional help sheet and implementation intention interventions showed similar effects after 1 month, with both groups reporting a significant increase in moderate-strenuous physical activity. After 3 months, the initial increase in physical activity was maintained by the volitional help sheet group, but not the implementation intention group. Improvements were also found for negative affect and emotional quality of life. While both interventions show promise in promoting physical activity in breast cancer survivors, the volitional help sheet may be more effective for facilitating lasting change and emotional well-being. Findings suggest that the volitional help sheet may have potential to offer a cost-effective contribution to consumer-led tertiary preventive health. Future research should test these initial findings in a definitive trial. Statement of contribution What is already known on this subject? Physical activity is important for optimizing health in breast cancer survivors. Despite this, physical activity in this cohort remains low. Theory-based strategies are needed to help breast cancer survivors independently manage and maintain regular physical activity over the long term. What does this study add? Online planning interventions can improve physical activity in breast cancer survivors. Volitional help sheets, but not implementation intentions, show sustained effects for 3 months. The intervention shows promise as a potential low-cost addition to long-term survivorship care plans. © 2018 The British Psychological Society.

Static renewal tests using Anodonta imbecillis (freshwater mussels). Anodonta imbecillis QA test 3, Clinch River-Environmental Restoration Program (CR-ERP)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Simbeck, D.J.

1994-12-31

Toxicity testing of split whole sediment samples using juvenile freshwater mussels (Anodonta imbecillis) was conducted by TVA to provide a quality assurance mechanism for test organism quality and overall performance of the test being conducted by CR-ERP personnel as part of the CR-ERP biomonitoring study of Clinch River sediments. Testing of sediment samples collected May 5 from Poplar Creek Miles 6.0 and 2.9 was conducted from May 10--19, 1994. Results from this test showed no toxicity (survival effects) to fresh-water mussels during a 9-day exposure to the sediments. Attachments to this report include: Chain of custody form -- original; Toxicitymore » test bench sheets; Ammonia analysis request and results; Meter calibration log sheets; and Training documentation forms.« less

Estimating the Minimum Number of Judges Required for Test-Centred Standard Setting on Written Assessments. Do Discussion and Iteration Have an Influence?

ERIC Educational Resources Information Center

Fowell, S. L.; Fewtrell, R.; McLaughlin, P. J.

2008-01-01

Absolute standard setting procedures are recommended for assessment in medical education. Absolute, test-centred standard setting procedures were introduced for written assessments in the Liverpool MBChB in 2001. The modified Angoff and Ebel methods have been used for short answer question-based and extended matching question-based papers,…

Comprehension of Written Grammar Test: Reliability and Known-Groups Validity Study with Hearing and Deaf and Hard-of-Hearing Students

ERIC Educational Resources Information Center

Cannon, Joanna E.; Hubley, Anita M.; Millhoff, Courtney; Mazlouman, Shahla

2016-01-01

The aim of the current study was to gather validation evidence for the "Comprehension of Written Grammar" (CWG; Easterbrooks, 2010) receptive test of 26 grammatical structures of English print for use with children who are deaf and hard of hearing (DHH). Reliability and validity data were collected for 98 participants (49 DHH and 49…

An Improvement of the Anisotropy and Formability Predictions of Aluminum Alloy Sheets

NASA Astrophysics Data System (ADS)

Banabic, D.; Comsa, D. S.; Jurco, P.; Wagner, S.; Vos, M.

2004-06-01

The paper presents an yield criterion for orthotropic sheet metals and its implementation in a theoretical model in order to calculate the Forming Limit Curves. The proposed yield criterion has been validated for two aluminum alloys: AA3103-0 and AA5182-0, respectively. The biaxial tensile test of cross specimens has been used for the determination of the experimental yield locus. The new yield criterion has been implemented in the Marciniak-Kuczynski model for the calculus of limit strains. The calculated Forming Limit Curves have been compared with the experimental ones, determined by frictionless test: bulge test, plane strain test and uniaxial tensile test. The predicted Forming Limit Curves using the new yield criterion are in good agreement with the experimental ones.

Chemical vapor deposition growth

NASA Technical Reports Server (NTRS)

Ruth, R. P.; Manasevit, H. M.; Campbell, A. G.; Johnson, R. E.; Kenty, J. L.; Moudy, L. A.; Shaw, G. L.; Simpson, W. I.; Yang, J. J.

1978-01-01

The objective was to investigate and develop chemical vapor deposition (CVD) techniques for the growth of large areas of Si sheet on inexpensive substrate materials, with resulting sheet properties suitable for fabricating solar cells that would meet the technical goals of the Low Cost Silicon Solar Array Project. The program involved six main technical tasks: (1) modification and test of an existing vertical-chamber CVD reactor system; (2) identification and/or development of suitable inexpensive substrate materials; (3) experimental investigation of CVD process parameters using various candidate substrate materials; (4) preparation of Si sheet samples for various special studies, including solar cell fabrication; (5) evaluation of the properties of the Si sheet material produced by the CVD process; and (6) fabrication and evaluation of experimental solar cell structures, using impurity diffusion and other standard and near-standard processing techniques supplemented late in the program by the in situ CVD growth of n(+)/p/p(+) sheet structures subsequently processed into experimental cells.

Robot-based additive manufacturing for flexible die-modelling in incremental sheet forming

NASA Astrophysics Data System (ADS)

Rieger, Michael; Störkle, Denis Daniel; Thyssen, Lars; Kuhlenkötter, Bernd

2017-10-01

The paper describes the application concept of additive manufactured dies to support the robot-based incremental sheet metal forming process (`Roboforming') for the production of sheet metal components in small batch sizes. Compared to the dieless kinematic-based generation of a shape by means of two cooperating industrial robots, the supporting robot models a die on the back of the metal sheet by using the robot-based fused layer manufacturing process (FLM). This tool chain is software-defined and preserves the high geometrical form flexibility of Roboforming while flexibly generating support structures adapted to the final part's geometry. Test series serve to confirm the feasibility of the concept by investigating the process challenges of the adhesion to the sheet surface and the general stability as well as the influence on the geometric accuracy compared to the well-known forming strategies.

Investigation of test methods, material properties, and processes for solar cell encapsulants. Fourteenth quarterly progress report, August 12, 1978-November 12, 1979. [EVA, EPDM, aliphatic urethane, PVC plastisol, and butyl acrylate

DOE Office of Scientific and Technical Information (OSTI.GOV)

Willis, P. B.; Baum, B.; Schnitzer, H. S.

1979-12-01

Springborn Laboratories is engaged in a study of evaluating potentially useful encapsulating materials for Task 3 of the Low-Cost Silicon Solar Array project (LSA) funded by DOE. The goal of this program is to identify, evaluate, and recommend encapsulant materials and processes for the production of cost-effective, long-life solar cell modules. This report presents the results of a cost analysis of candidate potting compounds for long life solar module encapsulation. Additionally, the two major encapsulation processes, sheet lamination and liquid casting, are costed on the basis of a large scale production facility. Potting compounds studied include EVA, sheet, clear; EVA,more » sheet, pigmented; EPDM, sheet, clear; Aliphatic urethane, syrup; PVC Plastisol; Butyl acrylate, syrup; and Butyl acrylate, sheet.« less

The effect of electron beam welding on the creep rupture properties of a Nb-Zr-C alloy

NASA Technical Reports Server (NTRS)

Moore, T. J.; Titran, R. H.; Grobstein, T. L.

1986-01-01

Creep rupture tests of electron beam welded PWC-11 sheet were conducted at 1350 K. Full penetration, single pass welds were oriented transverse to the testing direction in 1 mm thick sheet. With this orientation, stress was imposed equally on the base metal, weld metal, and heat-affected zone. Tests were conducted in both the postweld annealed and aged conditions. Unwelded specimens with similar heat treatments were tested for comparative purposes. It was found that the weld region is stronger than the base metal for both the annealed and aged conditions and that the PWC-11 material is stronger in the annealed condition than in the aged condition.

Comparing Tests for Diabetes and Prediabetes: A Quick Reference Guide

MedlinePlus

... Urinary Tract Imaging Urodynamic Testing Virtual Colonoscopy Diabetes & Prediabetes Tests This fact sheet compares the following tests: ... test Confirming Diagnosis of Type 2 Diabetes and Prediabetes Diagnosis must be confirmed unless symptoms are present. ...

Deformation Analysis of RC Ties Externally Strengthened with FRP Sheets

NASA Astrophysics Data System (ADS)

Gribniak, V.; Arnautov, A. K.; Kaklauskas, G.; Jakstaite, R.; Tamulenas, V.; Gudonis, E.

2014-11-01

The current study has two objectives: to validate the ability of the Atena finite-element software to estimate the deformations of reinforced concrete (RC) elements strengthened with fiber-reinforced polymer (FRP) sheets and to assess the effect of FRP-to-concrete bond strength on the results of numerical simulation. It is shown that the bond strength has to be selected according to the overall stiffness of the composite element. The numerical results found are corroborated experimentally by tensile tests of RC elements strengthened with basalt FRP sheets.

Experimental Investigation of the Capacity of Steel Fibers to Ensure the Structural Integrity of Reinforced Concrete Specimens Coated with CFRP Sheets

NASA Astrophysics Data System (ADS)

Gribniak, V.; Arnautov, A. K.; Norkus, A.; Tamulenas, V.; Gudonis, E.; Sokolov, A.

2016-07-01

The capacity of steel fibers to ensure the structural integrity of reinforced concrete specimens coated with CFRP sheets was investigated. Test data for four ties and eight beams reinforced with steel or glass-FRP bars are presented. Experiments showed that the fibers significantly increased the cracking resistance and altered the failure character from the splitting of concrete to the debonding of the external sheets, which noticeably increased the load-carrying capacity of the strengthened specimens.

Mechanical Properties of Titanium and Aluminum Alloys at Cryogenic Temperatures

DTIC Science & Technology

1962-03-01

aluminum alloys. Table I is a tabulation of the chemical composition of the tita - nium alloys. The bar was 5/8 inch in diameter and the sheet 0.060 inch...Ti-6AI-4V Tensile azid yield strength data for both bar and sheet of this tita - nium alloy are shown in Figure A-3. Bar and sheet data show approxi...not recommended for low temperature applications. The remainder of the tita - nium alloys were tested from room temperature to -452 F. In general, Ti

APPLICATION OF STEEL PIPE PILE LOADING TESTS TO DESIGN VERIFICATION OF FOUNDATION OF THE TOKYO GATE BRIDGE

NASA Astrophysics Data System (ADS)

Saitou, Yutaka; Kikuchi, Yoshiaki; Kusakabe, Osamu; Kiyomiya, Osamu; Yoneyama, Haruo; Kawakami, Taiji

Steel sheet pipe pile foundations with large diameter steel pipe sheet pile were used for the foundation of the main pier of the Tokyo Gateway bridge. However, as for the large diameter steel pipe pile, the bearing mechanism including a pile tip plugging effect is still unclear due to lack of the practical examinations even though loading tests are performed on Trans-Tokyo Bay Highway. In the light of the foregoing problems, static pile loading tests both vertical and horizontal directions, a dynamic loading test, and cone penetration tests we re conducted for determining proper design parameters of the ground for the foundations. Design parameters were determined rationally based on the tests results. Rational design verification was obtained from this research.

Slicing of Silicon into Sheet Material: Silicon Sheet Growth Development for the Large Area Silicon Sheet Task of the Low Cost Silicon Solar Array Project

NASA Technical Reports Server (NTRS)

Fleming, J. R.

1979-01-01

Testing of low cost low suspension power slurry vehicles is presented. Cutting oils are unlikely to work, but a mineral oil with additives should be workable. Two different abrasives were tested. A cheaper silicon carbide from Norton gave excellent results except for excessive kerf loss: the particles were too big. An abrasive treated for lubricity showed no lubricity improvement in mineral oil vehicle. The bounce fixture was tested for the first time under constant cut rate conditions (rather than constant force). Although the cut was not completed before the blades broke, the blade lifetime of thin (100 micrometer) blades was 120 times the lifetime without the fixture. The large prototype saw completed a successful run, producing 90% cutting yield (849 wafers) at 20 wafers/cm. Although inexperience with large numbers of wafers caused cleaning breakage to reduce this yield to 74%, the yield was high enough that the concept of the large saw is proven workable.

Usability of Optical Mark Reader Sheet as an Answering Tool in Testing.

PubMed

Booka, Masayuki; Oku, Hidehisa; Scheller, Andreas; Yamaoka, Shintaro

2017-01-01

The research result on usability of Optical Mark Reader Sheet (OMRS) being used as the standard answering tool is reported. The use of OMRS significantly requires more answer time than the answer time without OMRS, and the use of assistive devices for OMRS has the possibility to reduce the answer time.

Quantifying the movement of multiple insects using an optical insect counter

USDA-ARS?s Scientific Manuscript database

An optical insect counter (OIC) was designed and tested. The new system integrated a line-scan camera and a vertical light sheet along with data collection and image processing software to count numbers of flying insects crossing a vertical plane defined by the light sheet. The system also allows ...

Studies in Cup Drawing Behavior of Polymer Laminated Sheet Metal

NASA Astrophysics Data System (ADS)

Elnagmi, M.; Jain, M.; Bruhis, M.; Nielsen, K.

2011-08-01

Axisymmetric deep drawing behavior of a polymer laminated sheet metal (PLSM) is investigated using an axisymmetric cup drawing test. PLSMs are of interest as a replacement for painted finishes for automotive applications as they have the potential to achieve good quality long lasting and aesthetically appealing surfaces on stamped parts. However, there is limited understanding of PLSMs in automotive deep drawing situations to produce complex 3-D parts. The tests are carried out using well-controlled, laboratory-based, dual-action, servo-hydraulic forming presses under blank-holder force and punch displacement control conditions. An optical strain mapping system is used to measure the surface strains (and to construct 3D strain maps) from the film side of the deformed samples for a range of forming conditions. Deep drawing characteristics such as punch load versus punch displacement traces, strain distribution along the cup profile, flange wrinkling and fracture characteristics are experimentally assessed for stainless steel-plastic film laminated sheet materials. Also the effect of lamination pressure on wrinkling and delamination is investigated for a decorative pressure sensitive adhesive film affixed to the stainless steel sheet.

Anisotropy influence on the failure of Ti6Al4V sheets deformed at room and elevated temperature

NASA Astrophysics Data System (ADS)

Wang, Q. L.; Ghiotti, A.; Bruschi, S.

2018-05-01

Ti6Al4V sheets are usually difficult-to-form at room temperature as a consequence of their strong basal texture and hcp crystal lattice. The heating of the alloy below the beta transus temperature is recognized to enhance its formability, reducing the flow stress and increasing the ductility. However, the influence of the sheet anisotropy on the material failure hasn't been studied yet. To this aim, the paper presents the anisotropy influence on the failure characteristics of Ti6Al4V titanium alloy sheets making use of tensile tests carried out at room temperature and 600°C on smooth, notched and shear samples in order to have various stress states. The fracture strain is measured and the effect of the sample orientation and stress state is identified. To determine the actual stress state for each sample geometry, a numerical model is set up and calibrated using elasto-plastic data from uni-axial tensile tests on smooth samples. Finally, the fracture surfaces are observed through SEM analysis to explain the failure characteristics.

Impact of the storm-time plasma sheet ion composition on the ring current energy density

NASA Astrophysics Data System (ADS)

Mouikis, C.; Kistler, L. M.; Petrinec, S. M.; Fuselier, S. A.; Cohen, I.

2017-12-01

The adiabatic inward transport of the night-side near-earth ( 6 Re) hot plasma sheet is the dominant contributor to the ring current pressure during storm times. During storm times, the plasma sheet composition in the 6 - 12 Re tail region changes due to O+ entry from the lobes (from the cusp) and the direct feeding from the night side auroral region. In addition, at substorm onset the plasma sheet O+ ions can be preferentially accelerated. We use MMS and observations during two magnetic storms, 5/8/2016 and 7/16/2017, to monitor the composition changes and energization in the 6 - 12 Re plasma sheet region. For both storms the MMS apogee was in the tail. In addition, we use subsequent Van Allen Probe observations (with apogee in the dawn and dusk respectively) to test if the 6-12 Re plasma sheet, observed by MMS, is a sufficient source of the O+ in the ring current. For this we will compare the phase space density (PSD) of the plasma sheet source population and the PSD of the inner magnetosphere at constant magnetic moment values as used in Kistler et al., [2016].

[Jan Fryderyk Wolfgang's autobiography (1850) in the light of hand-written and printed sources].

PubMed

Kuźnicka, B

2001-01-01

The archival collection of the Lithuanian Academy of Sciences in Vilnius (Wilno) contains many manuscripts relating to the scientific work of Jan Fryderyk Wolfgang (1776-1859), professor of pharmacy and pharmacology of the Wilno University in the years 1807-1831, the founder and main figure in the Wilno pharmacognostic school, a botanist with substantial achievements in wide-ranging research on the flora of the Wilno region, as well as a historian of pharmacy. The most interesting of the manuscripts include Wolfgang's Autobiografia [Autobiography], written in 1850, and a list of his publications covering a total of 57 items (including some that have hitherto remained unknown), a work entitled Historya Farmakologii i Farmacyi [History of pharmacology and pharmacy], and a particularly valuable manuscript (666 + 12 sheets) entitled Farmakologiia [Pharmacology]. Worth mentioning are also two catalogues of books from Wolfgang's library: one compiled by Wolfgang himself (37 sheets) and the other by Adam Ferdynand Adamowicz. The content of the autobiography manuscript is contained on five sheets. The author of the present article analyzes the document, comparing the information contained in it with the biographies of J. F. Wolfgang that hhave been published so far (these being primarily the biography by Dominik Cezary ChodYko, published in 1863, and that by Witold W3odzimierz G3owacki of 1960). The text of the autobiography is quoted in full, together with numerous comments. The analysis of the manuscript as well as the biographical data contained in the above-mentioned biographies indicate that Wolfgang had great achievements as a scientist (in both research and organizational work), as a champion of public causes and as an educator of a generation of botanists-pharmacognostics. It also transpires from the autobiography, as well as from the research by historians, that he was a very good and trustful person, who readily granted access to his research to his collaborators and pupils. This eventually turned against him: he laments the loss of the materials of his floristic research "at untrustworthy hands" and deplores the fact that they were published under the name of other scientists. Jan Fryderyk Wolfgang died on 17 May 1859, in his estate at Po3uknie. He was buried at the no longer extant Lutheran graveyard at Pohulanka. A symbolic grave of Wolfgang is to be found at the Rossa Catholic cemetery in Wilno (sector XIV, grave no. 157).

10 CFR 26.127 - Procedures.

Code of Federal Regulations, 2014 CFR

2014-01-01

..., implement, and maintain written standard operating procedures for each assay performed for drug and specimen... facility shall develop, implement, and maintain written standard operating procedures for each test. The...; (2) Preparation of reagents, standards, and controls; (3) Calibration procedures; (4) Derivation of...

10 CFR 26.127 - Procedures.

Code of Federal Regulations, 2012 CFR

2012-01-01

..., implement, and maintain written standard operating procedures for each assay performed for drug and specimen... facility shall develop, implement, and maintain written standard operating procedures for each test. The...; (2) Preparation of reagents, standards, and controls; (3) Calibration procedures; (4) Derivation of...

10 CFR 26.127 - Procedures.

Code of Federal Regulations, 2013 CFR

2013-01-01

..., implement, and maintain written standard operating procedures for each assay performed for drug and specimen... facility shall develop, implement, and maintain written standard operating procedures for each test. The...; (2) Preparation of reagents, standards, and controls; (3) Calibration procedures; (4) Derivation of...

Understanding calving dynamics of Greenland outlet glaciers by comparing calving laws in a 3D ice sheet model

NASA Astrophysics Data System (ADS)

Choi, Y.; Morlighem, M.; Wood, M.; Bondzio, J. H.; Mouginot, J.

2017-12-01

Mass loss from marine terminating glaciers along coastal Greenland is a significant contributor to global sea-level rise. Calving is one of the important processes that control the dynamics, and therefore the discharge, of these glaciers. As glacier termini are exposed to warmer ocean currents, ocean-induced melt at the calving front increases, which may lead to glacier retreat and ice flow acceleration. It is therefore important to accurately parameterize calving in ice sheet models in order to improve the projections of ice sheet change. Several calving laws have been proposed, but most of them have been applied only to a specific region and have not been tested on other glaciers, while some others have only been implemented in one-dimensional flowline or vertical flowband models. Here, we test and compare several calving laws recently proposed in the literature using a 3D ice sheet model. Namely: the height-above-buoyancy criterion (Vieli et al., 2002), the crevasse-depth calving law (Benn et al., 2007), the eigencalving law (Levermann et al., 2012) and von Mises tensile stress calving law (Morlighem et al., 2016). We test these calving laws on Zachariae Isstrøm (Northeast), Upernavik (Central West) and Helheim (East) glaciers of Greenland. We compare the modeled ice front evolution to the observed retreat from Landsat data, and assess which calving law has the best predictive skills for each glacier. Overall, von Mises tensile stress calving laws is more satisfactory than others for most regions. This study shows that calving dynamics needs to be 3D in ice sheet models to account for the complex geometry and narrow fjords along the coast of Greenland. Comparing calving laws in a 3D model makes it possible to find missing mechanisms in each criterion and to improve existing calving laws in numerical ice sheet models, which could reduce uncertainties in future sea level rise projections.

Antifibrotic effect of dexamethasone/alginate-coated silicone sheet in the abraded middle ear mucosa.

PubMed

Jang, Chul Ho; Ahn, Seung Hyun; Kim, Geun Hyung

2016-12-01

Silicone sheet is a material which is commonly used in middle ear surgery to prevent the formation of adhesions between the tympanic membrane and the medial bony wall of the middle ear cavity. However, silicone sheet can induce a tight and hard fibrous capsule in the region of the stapes, and this is particularly common in cases of eustachian tube dysfunction. As a result of the fibrous encapsulation around the silicone sheet, postoperative aeration of the stapes can be interrupted causing poor hearing gain. In this study, we performed an in vitro and in vivo evaluation of the antifibrotic effects of a dexamethasone and alginate (Dx/alginate) coating on silicone sheet. The Dx/alginate-coated silicone sheets were fabricated using a plasma-treatment and coating method. The Dx/alginate-coated silicone sheets effectively limited in vitro fibroblast attachment and proliferation due to the controlled release of Dx, which can be modified by manipulation of the alginate coating. For the in-vivo evaluation, guinea pigs (albino, male, weighing 250g) were divided into two groups, with the control group (n=5) implanted with silicone sheet and the test group (n=5) receiving Dx/alginate-coated silicone sheet. Animals were sacrificed 3 weeks after implantation, and histological analysis was performed using hematoxylin and eosin (H&E) and immunohistochemical staining techniques. Dx/alginate-coated silicone sheets showed marked inhibition of fibrosis in both the in vitro and in vivo studies. Silicone sheet that incorporates a Dx/alginate coating can release Dx and inhibit fibrosis in the middle ear. This material could be utilized in middle ear surgery as a means of preserving proper aeration and hearing gain following ossiculoplasty. Copyright © 2016 Elsevier B.V. All rights reserved.

Microstructure evolution of a dissimilar junction interface between an Al sheet and a Ni-coated Cu sheet joined by magnetic pulse welding

DOE Office of Scientific and Technical Information (OSTI.GOV)

Itoi, Takaomi, E-mail: itoi@faculty.chiba-u.jp

An Al sheet and a Ni-coated Cu sheet were lap joined by using magnetic pulse welding (MPW). Tensile tests were performed on the joined sheets, and a good lap joint was achieved at a discharge energy of > 0.9 kJ. The weld interface exhibited a wavy morphology and an intermediate layer along the weld interface. Microstructure observations of the intermediate layer revealed that the Ni coating region consisted of a Ni–Al binary amorphous alloy and that the Al sheet region contained very fine Al nanograins. Ni fragments indicative of unmelted residual Ni from the coating were also observed in partsmore » of the intermediate layer. Formation of these features can be attributed to localize melting and a subsequent high rate cooling of molten Al and Ni confined to the interface during the MPW process. In the absence of an oxide film, atomic-scale bonding was also achieved between the intermediate layer and the sheet surfaces after the collision. MPW utilises impact energy, which affects the sheet surfaces. From the obtained results, good lap joint is attributed to an increased contact area, the anchor effect, work hardening, the absence of an oxide film, and suppressed formation of intermetallic compounds at the interface. - Highlights: •Good lap joint of an Al sheet and a Ni-coated Cu sheet was achieved by using magnetic pulse welding. •A Ni–Al binary amorphous alloy was formed as an intermediate layer at weld interface. •Atomic-scale bonding was achieved between the intermediate layer and the sheet surfaces.« less

Extent of the last ice sheet in northern Scotland tested with cosmogenic 10Be exposure ages

USGS Publications Warehouse

Phillips, W.M.; Hall, A.M.; Ballantyne, C.K.; Binnie, S.; Kubik, P.W.; Freeman, S.

2008-01-01

The extent of the last British-Irish Ice Sheet (BIIS) in northern Scotland is disputed. A restricted ice sheet model holds that at the global Last Glacial Maximum (LGM; ca. 23-19 ka) the BIIS terminated on land in northern Scotland, leaving Buchan, Caithness and the Orkney Islands ice-free. An alternative model implies that these three areas were ice-covered at the LGM, with the BIIS extending offshore onto the adjacent shelves. We test the two models using cosmogenic 10Be surface exposure dating of erratic boulders and glacially eroded bedrock from the three areas. Our results indicate that the last BIIS covered all of northern Scotland during the LGM, but that widespread deglaciation of Caithness and Orkney occurred prior to rapid warming at ca. 14.5 ka. Copyright ?? 2008 John Wiley & Sons, Ltd.

Response of Honeycomb Core Sandwich Panel with Minimum Gage GFRP Face-Sheets to Compression Loading After Impact

NASA Technical Reports Server (NTRS)

McQuigg, Thomas D.; Kapania, Rakesh K.; Scotti, Stephen J.; Walker, Sandra P.

2011-01-01

A compression after impact study has been conducted to determine the residual strength of three sandwich panel constructions with two types of thin glass fiber reinforced polymer face-sheets and two hexagonal honeycomb Nomex core densities. Impact testing is conducted to first determine the characteristics of damage resulting from various impact energy levels. Two modes of failure are found during compression after impact tests with the density of the core precipitating the failure mode present for a given specimen. A finite element analysis is presented for prediction of the residual compressive strength of the impacted specimens. The analysis includes progressive damage modeling in the face-sheets. Preliminary analysis results were similar to the experimental results; however, a higher fidelity core material model is expected to improve the correlation.

High-temperature sustainability of strong fiber Bragg gratings written into Sb-Ge-codoped photosensitive fiber: decay mechanisms involved during annealing.

PubMed

Shen, Yonghang; He, Jinglei; Sun, Tong; Grattan, Kenneth T V

2004-03-15

An antimony--germanium- (Sb--Ge-) codoped fiber specially designed for the fabrication of fiber Bragg gratings (FBGs) with high temperature sustainability has been developed. The photosensitivity and the high-temperature sustainability of FBGs that have been written into this fiber were tested. The results obtained showed that the FBG written into this fiber has a very high temperature sustainability of 900 degrees C. A decay mechanism that involves cation hopping is presented to explain the observed high temperature sustainability of the grating written into this fiber.

A systematic review of interventions to improve recall of medical advice in healthcare consultations

PubMed Central

Watson, Philip WB; McKinstry, Brian

2009-01-01

Abstract Background In order for patients to adhere to healthcare advice, it is essential that they are able to recall this following a consultation. Although psychological research exists which highlights techniques and factors postulated to influence recall, only a limited body of work has been conducted to evaluate their effectiveness in a clinical context. Aim To carry out a systematic review of intervention trials designed to enhance recall of medical information. Methods We searched Medline (1950–April 2007); Embase (1980–April 2007); Cinahl (1982–April 2007); PsychINFO (1969–2007); and the Cochrane Library Collection. Secondary searches were made through reference to relevant journals and reference lists from relevant papers/review papers. Results From 69 papers provisionally identified, 34 papers met the inclusion criteria. Nine recall interventions had been evaluated (audio recordings, written materials, adjunct questions, prompt sheets, visual aids, cognitive strategies, rehearsal, communication styles and personalized teaching). Despite the experimental and theoretical evidence which could have informed cognitive interventions to enhance recall of healthcare advice, most studies primarily focused on the use of written and/or audio-recorded medical instructions. Although the majority of studies supported these approaches insofar as they enhanced recall, the findings were equivocal. Conclusion While written and tape-recorded instructions appear to improve recall in most situations, a dearth of interventions incorporating psychological theory was readily apparent. Further research is required in clinical settings to determine if cognitive interventions based on a more over-arching psychological model of recall are effective. PMID:19531618

Nonlinear Dynamics of Non-uniform Current-Vortex Sheets in Magnetohydrodynamic Flows

NASA Astrophysics Data System (ADS)

Matsuoka, C.; Nishihara, K.; Sano, T.

2017-04-01

A theoretical model is proposed to describe fully nonlinear dynamics of interfaces in two-dimensional MHD flows based on an idea of non-uniform current-vortex sheet. Application of vortex sheet model to MHD flows has a crucial difficulty because of non-conservative nature of magnetic tension. However, it is shown that when a magnetic field is initially parallel to an interface, the concept of vortex sheet can be extended to MHD flows (current-vortex sheet). Two-dimensional MHD flows are then described only by a one-dimensional Lagrange parameter on the sheet. It is also shown that bulk magnetic field and velocity can be calculated from their values on the sheet. The model is tested by MHD Richtmyer-Meshkov instability with sinusoidal vortex sheet strength. Two-dimensional ideal MHD simulations show that the nonlinear dynamics of a shocked interface with density stratification agrees fairly well with that for its corresponding potential flow. Numerical solutions of the model reproduce properly the results of the ideal MHD simulations, such as the roll-up of spike, exponential growth of magnetic field, and its saturation and oscillation. Nonlinear evolution of the interface is found to be determined by the Alfvén and Atwood numbers. Some of their dependence on the sheet dynamics and magnetic field amplification are discussed. It is shown by the model that the magnetic field amplification occurs locally associated with the nonlinear dynamics of the current-vortex sheet. We expect that our model can be applicable to a wide variety of MHD shear flows.

Measuring the relationship between interruptions, multitasking and prescribing errors in an emergency department: a study protocol

PubMed Central

Raban, Magdalena Z; Walter, Scott R; Douglas, Heather E; Strumpman, Dana; Mackenzie, John; Westbrook, Johanna I

2015-01-01

Introduction Interruptions and multitasking are frequent in clinical settings, and have been shown in the cognitive psychology literature to affect performance, increasing the risk of error. However, comparatively less is known about their impact on errors in clinical work. This study will assess the relationship between prescribing errors, interruptions and multitasking in an emergency department (ED) using direct observations and chart review. Methods and analysis The study will be conducted in an ED of a 440-bed teaching hospital in Sydney, Australia. Doctors will be shadowed at proximity by observers for 2 h time intervals while they are working on day shift (between 0800 and 1800). Time stamped data on tasks, interruptions and multitasking will be recorded on a handheld computer using the validated Work Observation Method by Activity Timing (WOMBAT) tool. The prompts leading to interruptions and multitasking will also be recorded. When doctors prescribe medication, type of chart and chart sections written on, along with the patient's medical record number (MRN) will be recorded. A clinical pharmacist will access patient records and assess the medication orders for prescribing errors. The prescribing error rate will be calculated per prescribing task and is defined as the number of errors divided by the number of medication orders written during the prescribing task. The association between prescribing error rates, and rates of prompts, interruptions and multitasking will be assessed using statistical modelling. Ethics and dissemination Ethics approval has been obtained from the hospital research ethics committee. Eligible doctors will be provided with written information sheets and written consent will be obtained if they agree to participate. Doctor details and MRNs will be kept separate from the data on prescribing errors, and will not appear in the final data set for analysis. Study results will be disseminated in publications and feedback to the ED. PMID:26463224

Measuring the relationship between interruptions, multitasking and prescribing errors in an emergency department: a study protocol.

PubMed

Raban, Magdalena Z; Walter, Scott R; Douglas, Heather E; Strumpman, Dana; Mackenzie, John; Westbrook, Johanna I

2015-10-13

Interruptions and multitasking are frequent in clinical settings, and have been shown in the cognitive psychology literature to affect performance, increasing the risk of error. However, comparatively less is known about their impact on errors in clinical work. This study will assess the relationship between prescribing errors, interruptions and multitasking in an emergency department (ED) using direct observations and chart review. The study will be conducted in an ED of a 440-bed teaching hospital in Sydney, Australia. Doctors will be shadowed at proximity by observers for 2 h time intervals while they are working on day shift (between 0800 and 1800). Time stamped data on tasks, interruptions and multitasking will be recorded on a handheld computer using the validated Work Observation Method by Activity Timing (WOMBAT) tool. The prompts leading to interruptions and multitasking will also be recorded. When doctors prescribe medication, type of chart and chart sections written on, along with the patient's medical record number (MRN) will be recorded. A clinical pharmacist will access patient records and assess the medication orders for prescribing errors. The prescribing error rate will be calculated per prescribing task and is defined as the number of errors divided by the number of medication orders written during the prescribing task. The association between prescribing error rates, and rates of prompts, interruptions and multitasking will be assessed using statistical modelling. Ethics approval has been obtained from the hospital research ethics committee. Eligible doctors will be provided with written information sheets and written consent will be obtained if they agree to participate. Doctor details and MRNs will be kept separate from the data on prescribing errors, and will not appear in the final data set for analysis. Study results will be disseminated in publications and feedback to the ED. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

Advanced Duct Sealing Testing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sherman, Max H.; Walker, Iain S.

Duct leakage has been identified as a major source of energy loss in residential buildings. Most duct leakage occurs at the connections to registers, plenums or branches in the duct system. At each of these connections a method of sealing the duct system is required. Typical sealing methods include tapes or mastics applied around the joints in the system. Field examinations of duct systems have typically shown that these seals tend to fail over extended periods of time. The Lawrence Berkeley National Laboratory has been testing sealant durability for several years. Typical duct tape (i.e. fabric backed tapes with naturalmore » rubber adhesives) was found to fail more rapidly than all other duct sealants. This report summarizes the results of duct sealant durability testing of five UL 181B-FX listed duct tapes (three cloth tapes, a foil tape and an Oriented Polypropylene (OPP) tape). One of the cloth tapes was specifically developed in collaboration with a tape manufacturer to perform better in our durability testing. The first test involved the aging of common ''core-to-collar joints'' of flexible duct to sheet metal collars, and sheet metal ''collar-to-plenum joints'' pressurized with 200 F (93 C) air. The second test consisted of baking duct tape specimens in a constant 212 F (100 C) oven following the UL 181B-FX ''Temperature Test'' requirements. Additional tests were also performed on only two tapes using sheet metal collar-to-plenum joints. Since an unsealed flexible duct joint can have a variable leakage depending on the positioning of the flexible duct core, the durability of the flexible duct joints could not be based on the 10% of unsealed leakage criteria. Nevertheless, the leakage of the sealed specimens prior to testing could be considered as a basis for a failure criteria. Visual inspection was also documented throughout the tests. The flexible duct core-to-collar joints were inspected monthly, while the sheet metal collar-to-plenum joints were inspected weekly. The baking test specimens were visually inspected weekly, and the durability was judged by the observed deterioration in terms of brittleness, cracking, flaking and blistering (the terminology used in the UL 181B-FX test procedure).« less

Tensile Properties of 17-7 PH and 12 MoV Stainless-Steel Sheet under Rapid-Heating and Constant-Temperature Conditions

NASA Technical Reports Server (NTRS)

Manning, Charles R., Jr.; Price, Howard L.

1961-01-01

Results are presented of rapid-heating tests of 17-7 PH and 12 MoV stainless-steel sheet heated to failure at temperature rates from about 1 F to 170 F per second under constant-load conditions. Yield and rupture strengths obtained from rapid-heating tests are compared with yield and tensile strengths obtained from short-time elevated-temperature tensile tests (30-minute exposure). A rate-temperature parameter was used to construct master curves from which yield and rupture stresses or temperatures can be predicted. A method for measuring strain by optical means is described.

Gravimetric screening method for fungal decay of paper: inoculation with Trametes versicolor.

PubMed

Råberg, Ulrika; Hafrén, Jonas

2009-10-01

The European standard test EN 113 for fungal degradation of solid wood has been adapted for degradation of paper by white rot fungus (Trametes versicolor). Fungal degradation of paper sheets may potentially be used for screening different wood preservatives on paper instead of solid wood. The paper samples showed higher relative mass losses compared to wood, and samples pretreated with boric acid, copper sulfate and polymerized linseed oil were successfully tested for biodegradation using the paper sheet method. The results on paper degradation were compared with wood, both as wood blocks (according to standard test) and wood cut in sections forming layered structures mimicking paper layers.

Sense and readability: participant information sheets for research studies.

PubMed

Ennis, Liam; Wykes, Til

2016-02-01

Informed consent in research is partly achieved through the use of information sheets. There is a perception however that these information sheets are long and complex. The recommended reading level for patient information is grade 6, or 11-12 years old. To investigate whether the readability of participant information sheets has changed over time, whether particular study characteristics are related to poorer readability and whether readability and other study characteristics are related to successful study recruitment. Method: We obtained 522 information sheets from the UK National Institute for Health Research Clinical Research Network: Mental Health portfolio database and study principal investigators. Readability was assessed with the Flesch reading index and the Grade level test. Information sheets increased in length over the study period. The mean grade level across all information sheets was 9.8, or 15-16 years old. A high level of patient involvement was associated with more recruitment success and studies involving pharmaceutical or device interventions were the least successful. The complexity of information sheets had little bearing on successful recruitment. Information sheets are far more complex than the recommended reading level of grade 6 for patient information. The disparity may be exacerbated by an increasing focus on legal content. Researchers would benefit from clear guidance from ethics committees on writing succinctly and accessibly and how to balance the competing legal issues with the ability of participants to understand what a study entails. © The Royal College of Psychiatrists 2016.

Sense and readability: participant information sheets for research studies

PubMed Central

Ennis, Liam; Wykes, Til

2016-01-01

Background Informed consent in research is partly achieved through the use of information sheets. There is a perception however that these information sheets are long and complex. The recommended reading level for patient information is grade 6, or 11–12 years old. Aims To investigate whether the readability of participant information sheets has changed over time, whether particular study characteristics are related to poorer readability and whether readability and other study characteristics are related to successful study recruitment. Method We obtained 522 information sheets from the UK National Institute for Health Research Clinical Research Network: Mental Health portfolio database and study principal investigators. Readability was assessed with the Flesch reading index and the Grade level test. Results Information sheets increased in length over the study period. The mean grade level across all information sheets was 9.8, or 15–16 years old. A high level of patient involvement was associated with more recruitment success and studies involving pharmaceutical or device interventions were the least successful. The complexity of information sheets had little bearing on successful recruitment. Conclusions Information sheets are far more complex than the recommended reading level of grade 6 for patient information. The disparity may be exacerbated by an increasing focus on legal content. Researchers would benefit from clear guidance from ethics committees on writing succinctly and accessibly and how to balance the competing legal issues with the ability of participants to understand what a study entails. PMID:26382948

The Influence of a Response Format Test Accommodation for College Students with and without Disabilities

ERIC Educational Resources Information Center

Potter, Kyle; Lewandowski, Lawrence; Spenceley, Laura

2016-01-01

Standardised and other multiple-choice examinations often require the use of an answer sheet with fill-in bubbles (i.e. "bubble" or Scantron sheet). Students with disabilities causing impairments in attention, learning and/or visual-motor skill may have difficulties with multiple-choice examinations that employ such a response style.…

Mathematics and Science Test Gaps. Pell Institute Fact Sheet. Updated

ERIC Educational Resources Information Center

Pell Institute for the Study of Opportunity in Higher Education, 2011

2011-01-01

Data is reported as percentages in 4th, 8th, and 12th grades based on proficiency in the subject ("Below Basic," "At Basic," "At Proficient", or "At Advanced"). "Low-income" on this data sheet means students who qualify for the National School Lunch Program. Both math and science data are from 2009…

Creep-rupture tests of internally pressurized Rene 41 tubes

NASA Technical Reports Server (NTRS)

Gumto, K. H.; Weiss, B.

1972-01-01

Weld-drawn tubes of Rene 41 with 0.935 centimeter outside diameter and 0.064 centimeter wall thickness were tested to failure at temperatures from 1117 to 1233 K and internal helium pressures from 5.5 to 12.4 meganewtons per square meter. Lifetimes ranged from 5 to 2065 hours. The creep-rupture strength of the tubes was 50 percent lower than that of unwelded, thick sheet specimens, and 20 percent lower than that of unwelded, thin sheet specimens. Larson-Miller correlations and photomicrographs of some specimens are presented.

In vivo feasibility test using transparent carbon nanotube-coated polydimethylsiloxane sheet at brain tissue and sciatic nerve.

PubMed

Wang, Caifeng; Oh, Sangjin; Lee, Hyun Ah; Kang, Jieun; Jeong, Ki-Jae; Kang, Seon Woo; Hwang, Dae Youn; Lee, Jaebeom

2017-06-01

Carbon nanotubes, with their unique and outstanding properties, such as strong mechanical strength and high electrical conductivity, have become very popular for the repair of tissues, particularly for those requiring electrical stimuli. Polydimethylsiloxane (PDMS)-based elastomers have been used in a wide range of biomedical applications because of their optical transparency, physiological inertness, blood compatibility, non-toxicity, and gas permeability. In present study, most of artificial nerve guidance conduits (ANGCs) are not transparent. It is hard to confirm the position of two stumps of damaged nerve during nerve surgery and the conduits must be cut open again to observe regenerative nerves after surgery. Thus, a novel preparation method was utilized to produce a transparent sheet using PDMS and multiwalled carbon nanotubes (MWNTs) via printing transfer method. Characterization of the PDMS/MWNT (PM) sheets revealed their unique physicochemical properties, such as superior mechanical strength, a certain degree of electrical conductivity, and high transparency. Characterization of the in vitro and in vivo usability was evaluated. PM sheets showed high biocompatibility and adhesive ability. In vivo feasibility tests of rat brain tissue and sciatic nerve revealed the high transparency of PM sheets, suggesting that it can be used in the further development of ANGCs. © 2017 Wiley Periodicals, Inc. J Biomed Mater Res Part A: 105A: 1736-1745, 2017. © 2017 Wiley Periodicals, Inc.

Stamping of Thin-Walled Structural Components with Magnesium Alloy AZ31 Sheets

NASA Astrophysics Data System (ADS)

Chen, Fuh-Kuo; Chang, Chih-Kun

2005-08-01

In the present study, the stamping process for manufacturing cell phone cases with magnesium alloy AZ31 sheets was studied using both the experimental approach and the finite element analysis. In order to determine the proper forming temperature and set up a fracture criterion, tensile tests and forming limit tests were first conducted to obtain the mechanical behaviors of AZ31 sheets at various elevated temperatures. The mechanical properties of Z31 sheets obtained from the experiments were then adopted in the finite element analysis to investigate the effects of the process parameters on the formability of the stamping process of cell phone cases. The finite element simulation results revealed that both the fracture and wrinkle defects could not be eliminated at the same time by adjusting blank-holder force or blank size. A drawbead design was then performed using the finite element simulations to determine the size and the location of drawbead required to suppress the wrinkle defect. An optimum stamping process, including die geometry, forming temperature, and blank dimension, was then determined for manufacturing the cell phone cases. The finite element analysis was validated by the good agreement between the simulation results and the experimental data. It confirms that the cell phone cases can be produced with magnesium alloy AZ31 sheet by the stamping process at elevated temperatures.

Modeling the growth and decay of the Antarctic Peninsula Ice Sheet

NASA Astrophysics Data System (ADS)

Payne, A. J.; Sugden, D. E.; Clapperton, C. M.

1989-03-01

A model of the growth and decay of the Antarctic Peninsula Ice Sheet during the last glacial/interglacial cycle is used to identify the main controls on ice sheet behavior. Using as input glaciological assumptions derived by W. F. Budd and I. N. Smith (1982, Annals of Glaciology3, 42-49), bedrock topography, isostatic compensation, and mass balance relationships, the model is driven by sea-level change over the last 40,000 yr in association with assumed changes in the rate of melting beneath ice shelves. An ice sheet dome over 3.5 km thick grows on the offshore shelf and straits west of the Antarctic Peninsula and reaches a maximum at 18,000 yr B.P. Collapse begins at 14,000 yr B.P. but becomes rapid and continuous after 10,000 yr B.P. The present stable ice cover is achieved at 6500 yr B.P. Ice growth and decay are characterized by thresholds which separate periods of steady state from periods of rapid transition; the thresholds usually relate to topography. Tests show that ice sheet behavior is most sensitive to sea-level change, basal marine melting, and accumulation and is less sensitive to isostasy, spatial variation in accumulation, calving rates, and ice flow parameterization. Tests of the model against field evidence show good agreement in places, as well as discrepancies which require further work.

Properties of hot-rolled sheets from ferritic steel with increased strength

NASA Astrophysics Data System (ADS)

Perlovich, Yu.; Isaenkova, M.; Dobrokhotov, P.; Stolbov, S.; Bannykh, O.; Bannykh, I.; Antsyferova, M.

2017-10-01

Sheets from ferritic steel 3 mm thick with increased strength after thermal hardening were studied by use of various X-ray methods and mechanical testing. Rolling of steel was carried out at 1100°C with rather great reductions per pass, so that plastic deformation of metal spread by the significant distance from the surface. The texture of sheet proved to have two sharply different layers: the inner layer of ˜40% thick with the usual rolling texture of BCC metals and the external layer with the rolling texture of FCC metals. At that, within the intermediate layer the texture is weakened. Texture formation within the external layer is conditioned by the process of dynamical deformation ageing: interstitial impurities from atmosphere block dislocations, prevent from their slip and at increased temperatures promote their collective climb. As a result, the direction of lattice rotation as well as the final rolling texture change. Due to texture layering, by impact testing of the sheet the plane of crack propagation must be changed when this crack reaches the inner layer, and then an additional energy for its further movement is required. Thermal hardening of the sheet retains the type of rolling texture, though results in some its scattering, but at the same time the breaking point of steel grows twice owing to formation of intermetallic particles.

Labeling and advertising of home insulation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

This staff report, prepared by the F.T.C.'s Bureau of Consumer Protection for Commission review, includes recommendations as to the final form of a trade regulation rule relating to the labeling and advertising of home insulation. Because of marketing abuses which accompanied the rising demand for home insulation, there has been broad support for a rule requiring information disclosures to help purchasers of home insulation to make an informed decision. The Commission, to provide such rule as quickly as possible, undertook its rulemaking proceeding under its new expedited rulemaking procedure. The rule was proposed on November 18, 1977, and, following amore » two-month period for written comments, four weeks of hearings were held in Washington, D.C. in February 1978. The record, contributed to by a variety of interests, shows that consumers do not know how to shop for home insulation. The staff-recommended rule, among other things, would require that insulation be tested and R-values (a measure of insulation's ability to retain heat) disclosed on labels and in advertising. To facilitate comparison shopping, the industry would also be required to furnish consumers with fact sheets describing, on a product-to-product basis, factors that can reduce the R-value of insulation.« less

House Dust Mite Prevalence in the House of Patients with Atopic Dermatitis in Mashhad, Iran.

PubMed

Ziyaei, Toktam; Berenji, Fariba; Jabbari-Azad, Farahzad; Fata, Abdolmajid; Jarahi, Lida; Fereidouni, Mohammad

2017-06-01

Being exposed to house dust mites intensifies atopic dermatitis. This study has investigated the contamination rate with Dermatophagoides mites in patient's residential home with atopic dermatitis. In this cross-sectional study, 40 patients took part with atopic dermatitis (positive or negative for mites by prick Dermal Test). Samples were collected from 3 locations (living room, bedroom and bed) by vacuum cleaner. Dust samples (transferred to freezer -20 °C) were examined by direct method and flotation. The data were analyzed using statistical SPSS vr.20 software. Twenty patients of positive prick test included 8 (40%) male and 12 (60%) female. The results of direct observation of mites: 7 cases (35%) in bedding sheets, 6 cases (30%) bedrooms' carpet, 3 cases (15%) living room's carpet. Twenty patients of negative prick test included 8 (40%) male and 12 (60%) female. Only mites were found (5%) in living room's carpets of negative prick test patients. Dermatophagoides pteronyssinus was more frequent than Dermatophagoides farina e. (98% vs 83%). Fifty-five percent of residential homes of prick test positive patients and only 5% of residential homes of prick test negative patients were positive for mite. Sunshine provided home had fewer mites than home where sunshine is not provided. Prick test positive patients used handmade carpets more than machine made ones. In positive prick test patients, mites were found in bed sheet and bedroom's carpet more than negative prick test patient's sheets and carpets.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jozsef, G

Purpose: To build a test device for HDR afterloaders capable of checking source positions, times at positions and estimate the activity of the source. Methods: A catheter is taped on a plastic scintillation sheet. When a source travels through the catheter, the scintillator sheet lights up around the source. The sheet is monitored with a video camera, and records the movement of the light spot. The center of the spot on each image on the video provides the source location, and the time stamps of the images can provide the dwell time the source spend in each location. Finally, themore » brightness of the light spot is related to the activity of the source. A code was developed for noise removal, calibrate the scale of the image to centimeters, eliminate the distortion caused by the oblique view angle, identifying the boundaries of the light spot, transforming the image into binary and detect and calculate the source motion, positions and times. The images are much less noisy if the camera is shielded. That requires that the light spot is monitored in a mirror, rather than directly. The whole assembly is covered from external light and has a size of approximately 17×35×25cm (H×L×W) Results: A cheap camera in BW mode proved to be sufficient with a plastic scintillator sheet. The best images were resulted by a 3mm thick sheet with ZnS:Ag surface coating. The shielding of the camera decreased the noise, but could not eliminate it. A test run even in noisy condition resulted in approximately 1 mm and 1 sec difference from the planned positions and dwell times. Activity tests are in progress. Conclusion: The proposed method is feasible. It might simplify the monthly QA process of HDR Brachytherapy units.« less

Morphological and antibacterial properties of modified paper by PS nanocomposites for packaging applications.

PubMed

Youssef, Ahmed M; Kamel, S; El-Samahy, M A

2013-10-15

With the increasing sustainability trend with packaging materials, paper and polymer nanocomposites represent a novel class of packaging materials. This study evaluates the potential achievement of alternative sustainable materials as antibacterial packaging application. Paper sheet from rice straw coated with 5 or 10% polystyrene (PS) nanocomposites using titanium dioxide nanoparticles (TiO2-NPs) doped or undoped with sliver nanoparticles (Ag-NPs) were prepared. The morphology of the uncoated and coated paper sheets was studied by SEM. The treated paper sheets were analyzed for their elemental composition using EDAX. The Barrier, air permeability, cob test, as well as mechanical properties and tensile strength were also evaluated. The inhibitory effect of modified paper sheets against Pseudomonas, Staphylococcus aureus, Candida, and Staphylococcus were investigated. Copyright © 2013 Elsevier Ltd. All rights reserved.

Concrete testing device provides substantial savings : fact sheet.

DOT National Transportation Integrated Search

2011-11-01

Current practices require a permeability test, ASTM C1202: "Standard Test Method for Electrical Indication of Concrete's Ability to resist Chloride Ion Penetration," for structures with potential salt water intrusion. The test is run at 56 days of ag...

Assessing the reading comprehension of adults with learning disabilities.

PubMed

Jones, F W; Long, K; Finlay, W M L

2006-06-01

This study's aim was to begin the process of measuring the reading comprehension of adults with mild and borderline learning disabilities, in order to generate information to help clinicians and other professionals to make written material for adults with learning disabilities more comprehensible. The Test for the Reception of Grammar (TROG), with items presented visually rather than orally, and the Reading Comprehension sub-test of the Wechsler Objective Reading Dimensions (WORD) battery were given to 24 service-users of a metropolitan community learning disability team who had an estimated IQ in the range 50-79. These tests were demonstrated to have satisfactory split-half reliability and convergent validity with this population, supporting both their use in this study and in clinical work. Data are presented concerning the distribution across the sample of reading-ages and the comprehension of written grammatical constructions. These data should be useful to those who are preparing written material for adults with learning disabilities.

Experimental Method for Characterizing Electrical Steel Sheets in the Normal Direction

PubMed Central

Hihat, Nabil; Lecointe, Jean Philippe; Duchesne, Stephane; Napieralska, Ewa; Belgrand, Thierry

2010-01-01

This paper proposes an experimental method to characterise magnetic laminations in the direction normal to the sheet plane. The principle, which is based on a static excitation to avoid planar eddy currents, is explained and specific test benches are proposed. Measurements of the flux density are made with a sensor moving in and out of an air-gap. A simple analytical model is derived in order to determine the permeability in the normal direction. The experimental results for grain oriented steel sheets are presented and a comparison is provided with values obtained from literature. PMID:22163394

Effect of Brake Forming on the Strength of 24S-T Aluminum-alloy Sheet

NASA Technical Reports Server (NTRS)

Heimerl, George J; Woods, Walter

1946-01-01

Tests were made to determine the effect of brake forming on the strength of 24S-T aluminum alloy sheet that had been formed to an inside bend radius of three times the sheet thickness. The results for both directions of the grain of the material showed that the compressive yield stresses were appreciably increased, that the tensile yield stresses were moderately increased, that the ultimate tensile stresses were only slightly increased, that the elongations were considerably reduced, and that the shapes of the tensile and compressive stress-strain curves were markedly changed.

Experimental Study of Deformation and of Effective Width in Axially Loaded Sheet-stringer Panels

NASA Technical Reports Server (NTRS)

Ramberg, Walter; MCPHERSON ALBERT E; Levy, Sam

1939-01-01

The deformation of two sheet-stringer panels subjected to end compression under carefully controlled end conditions was measured at a number of points and at a number of loads, most of which were above the load at which the sheet had begun to buckle. The two panels were identical except for the sheet, which was 0.70-inch 24st alclad for specimen 1 and 0.025-inch 24st aluminum alloy for specimen 6. A technique was developed for attaching Tuckerman optical strain gauges to the sheet without disturbing the strain distribution in the sheet by the method of attachment. This technique was used to explore the strain distribution in the sheet at various loads. The twisting and the bending of the stringers was measured by means of pointers attached to the stringers. The shape of the buckles in the sheet of specimen 6 was recorded at two loads by means of plaster casts. The sheet and the stringer loads at failure are compared with the corresponding loads for five similar panels tested at the Navy Model Basin. A detailed comparison is made between the measured deformation of the buckled sheet and the deformation calculated from approximate theories for the deformation in a rectangular sheet with freely supported edges buckling under end compression advanced by Timoshenko, Frankland, and Marguerre. The measured effective width for the specimens is compared with the effective width given by nine different relations for effective width as a function of the edge stress divided by the buckling stress of the sheet. The analysis of the measured stringer deformation is confined to an application of Southwell's method of plotting deformation against deformation over load. It was concluded that the stringer failure in both specimens were due to an instability in which the stringer was simultaneously twisted and bent as a column.

Achievement Test Program.

ERIC Educational Resources Information Center

Ohio State Dept. of Education, Columbus. Trade and Industrial Education Service.

The Ohio Trade and Industrial Education Achievement Test battery is comprised of seven basic achievement tests: Machine Trades, Automotive Mechanics, Basic Electricity, Basic Electronics, Mechanical Drafting, Printing, and Sheet Metal. The tests were developed by subject matter committees and specialists in testing and research. The Ohio Trade and…

Novel antibacterial mouthguard material manufactured using silver-nanoparticleembedded ethylene-vinyl acetate copolymer masterbatch.

PubMed

Yoshida, Yuriko; Churei, Hiroshi; Takeuchi, Yasuo; Wada, Takahiro; Uo, Motohiro; Izumi, Yuichi; Ueno, Toshiaki

2018-01-26

The purpose of the present study was to develop an antibacterial mouthguard (MG) material using a masterbatch of silvernanoparticle-embedded ethylene-vinyl acetate (EVA) copolymers. In order to verify that the testing material was clinically applicable as an antibacterial MG material, we conducted an antibacterial test, a shock absorption test, and analysis of in vitro silver release. The colony-forming activity of Streptococcus sobrinus, Porphyromonas gingivalis, and Escherichia coli were significantly inhibited on the testing materials compared with the commercial EVA sheet (p<0.05). The shock absorption capability of the testing material was not significantly different from that of the commercial EVA sheet. Cumulative silver release (in pure water) from the testing materials were infinitesimal after soaking for 20 days, which implied that there could be no harm in wearing the MG during exercise. These results showed that this testing material could be clinically applicable as an antibacterial MG material.

AtomPy: an open atomic-data curation environment

NASA Astrophysics Data System (ADS)

Bautista, Manuel; Mendoza, Claudio; Boswell, Josiah S; Ajoku, Chukwuemeka

2014-06-01

We present a cloud-computing environment for atomic data curation, networking among atomic data providers and users, teaching-and-learning, and interfacing with spectral modeling software. The system is based on Google-Drive Sheets, Pandas (Python Data Analysis Library) DataFrames, and IPython Notebooks for open community-driven curation of atomic data for scientific and technological applications. The atomic model for each ionic species is contained in a multi-sheet Google-Drive workbook, where the atomic parameters from all known public sources are progressively stored. Metadata (provenance, community discussion, etc.) accompanying every entry in the database are stored through Notebooks. Education tools on the physics of atomic processes as well as their relevance to plasma and spectral modeling are based on IPython Notebooks that integrate written material, images, videos, and active computer-tool workflows. Data processing workflows and collaborative software developments are encouraged and managed through the GitHub social network. Relevant issues this platform intends to address are: (i) data quality by allowing open access to both data producers and users in order to attain completeness, accuracy, consistency, provenance and currentness; (ii) comparisons of different datasets to facilitate accuracy assessment; (iii) downloading to local data structures (i.e. Pandas DataFrames) for further manipulation and analysis by prospective users; and (iv) data preservation by avoiding the discard of outdated sets.

Characterization of Platinum Nanoparticles Deposited on Functionalized Graphene Sheets

PubMed Central

Chiang, Yu-Chun; Liang, Chia-Chun; Chung, Chun-Ping

2015-01-01

Due to its special electronic and ballistic transport properties, graphene has attracted much interest from researchers. In this study, platinum (Pt) nanoparticles were deposited on oxidized graphene sheets (cG). The graphene sheets were applied to overcome the corrosion problems of carbon black at operating conditions of proton exchange membrane fuel cells. To enhance the interfacial interactions between the graphene sheets and the Pt nanoparticles, the oxygen-containing functional groups were introduced onto the surface of graphene sheets. The results showed the Pt nanoparticles were uniformly dispersed on the surface of graphene sheets with a mean Pt particle size of 2.08 nm. The Pt nanoparticles deposited on graphene sheets exhibited better crystallinity and higher oxygen resistance. The metal Pt was the predominant Pt chemical state on Pt/cG (60.4%). The results from the cyclic voltammetry analysis showed the value of the electrochemical surface area (ECSA) was 88 m2/g (Pt/cG), much higher than that of Pt/C (46 m2/g). The long-term test illustrated the degradation in ECSA exhibited the order of Pt/C (33%) > Pt/cG (7%). The values of the utilization efficiency were calculated to be 64% for Pt/cG and 32% for Pt/C. PMID:28793577

Development of sheet-metal parabolic-trough reflector panels

NASA Astrophysics Data System (ADS)

Biester, A. W.

1982-06-01

Efforts to develop accurate, durable, and mass producible sheet metal parabolic trough solar collectors and the associated support for the collectors are described. The design considered is similar to an automobile hood, a two-piece sheet metal structure consisting of a formed steel frame or stiffening panel and a smooth contoured skin. The two pieces may be bonded or welded to form a rigid structure, and a reflective surface applied such as a film, glass mirror, or any of the presently utilized materials. The work encompassed material selection, adhesive selection and testing, tool design and fabrication, prototype panel production, and design and development of torque tube assemblies on which the trough is inclined. Results of adhesive bonding studies are given. It is found that high volume technology can be used to produce accurate and structurally sound reflector panels, and one configuration was selected for fabrication in suitable quantities for performance testing.

Testing single point incremental forming moulds for rotomoulding operations

NASA Astrophysics Data System (ADS)

Afonso, Daniel; de Sousa, Ricardo Alves; Torcato, Ricardo

2017-10-01

Low pressure polymer processes as thermoforming or rotational moulding use much simpler moulds than high pressure processes like injection. However, despite the low forces involved in the process, moulds manufacturing for these applications is still a very material, energy and time consuming operation. Particularly in rotational moulding there is no standard for the mould manufacture and very different techniques are applicable. The goal of this research is to develop and validate a method for manufacturing plastically formed sheet metal moulds by single point incremental forming (SPIF) for rotomoulding and rotocasting operations. A Stewart platform based SPIF machine allow the forming of thick metal sheets, granting the required structural stiffness for the mould surface, and keeping a short manufacture lead time and low thermal inertia. The experimental work involves the proposal of a hollow part, design and fabrication of a sheet metal mould using dieless incremental forming techniques and testing its operation in the production of prototype parts.

Release-rate calorimetry of multilayered materials for aircraft seats

NASA Technical Reports Server (NTRS)

Fewell, L. L.; Duskin, F. E.; Spieth, H.; Trabold, E.; Parker, J. A.

1979-01-01

Multilayered samples of contemporary and improved fire resistant aircraft seat materials (foam cushion, decorative fabric, slip sheet, fire blocking layer, and cushion reinforcement layer) were evaluated for their rates of heat release and smoke generation. Top layers (decorative fabric, slip sheet, fire blocking, and cushion reinforcement) with glass fiber block cushion were evaluated to determine which materials based on their minimum contributions to the total heat release of the multilayered assembly may be added or deleted. Top layers exhibiting desirable burning profiles were combined with foam cushion materials. The smoke and heat release rates of multilayered seat materials were then measured at heat fluxes of 1.5 and 3.5 W/sq cm. Choices of contact and silicone adhesives for bonding multilayered assemblies were based on flammability, burn and smoke generation, animal toxicity tests, and thermal gravimetric analysis. Abrasion tests were conducted on the decorative fabric covering and slip sheet to ascertain service life and compatibility of layers.

An Anisotropic Model for Magnetostriction and Magnetization Computing for Noise Generation in Electric Devices.

PubMed

Mbengue, Serigne Saliou; Buiron, Nicolas; Lanfranchi, Vincent

2016-04-16

During the manufacturing process and use of ferromagnetic sheets, operations such as rolling, cutting, and tightening induce anisotropy that changes the material's behavior. Consequently for more accuracy in magnetization and magnetostriction calculations in electric devices such as transformers, anisotropic effects should be considered. In the following sections, we give an overview of a macroscopic model which takes into account the magnetic and magnetoelastic anisotropy of the material for both magnetization and magnetostriction computing. Firstly, a comparison between the model results and measurements from a Single Sheet Tester (SST) and values will be shown. Secondly, the model is integrated in a finite elements code to predict magnetostrictive deformation of an in-house test bench which is a stack of 40 sheets glued together by the Vacuum-Pressure Impregnation (VPI) method. Measurements on the test bench and Finite Elements results are presented.

A kinematic hardening constitutive model for the uniaxial cyclic stress-strain response of magnesium sheet alloys at room temperature

NASA Astrophysics Data System (ADS)

He, Zhitao; Chen, Wufan; Wang, Fenghua; Feng, Miaolin

2017-11-01

A kinematic hardening constitutive model is presented, in which a modified form of von Mises yield function is adopted, and the initial asymmetric tension and compression yield stresses of magnesium (Mg) alloys at room temperature (RT) are considered. The hardening behavior was classified into slip, twinning, and untwinning deformation modes, and these were described by two forms of back stress to capture the mechanical response of Mg sheet alloys under cyclic loading tests at RT. Experimental values were obtained for AZ31B-O and AZ31B sheet alloys under both tension-compression-tension (T-C-T) and compression-tension (C-T) loadings to calibrate the parameters of back stresses in the proposed model. The predicted parameters of back stresses in the twinning and untwinning modes were expressed as a cubic polynomial. The predicted curves based on these parameters showed good agreement with the tests.

Development and Evaluation of TiAl Sheet Structures for Hypersonic Applications

NASA Technical Reports Server (NTRS)

Draper, S. L.; Krause, D.; Lerch, B.; Locci, I. E.; Doehnert, B.; Nigam, R.; Das, G.; Sickles, P.; Tabernig, B.; Reger, N.;

Implementation of Socioscientific Issues Instruction to Fostering Students’ Decision Making Based Gender on Environmental Pollution

NASA Astrophysics Data System (ADS)

Rizal, H. P.; Siahaan, P.; Yuliani, G.

2017-02-01

The purpose of this study was to investigate the implementation socioscientific issues (SSI) instruction to examine students’ decision making based gender. Selection of environmental problem based on the consideration this issue has potential to evaluate from various scientific disciplines and may initiate to make decision. The participant was students grade VII in South Sulawesi. Pre experiment method was utilized in study with one group pre-test and post-test design. The instrument used in this study comprised of open-ended question, observation sheets for group discussion, sheet for interview and observation sheet of implementation instruction in class. The result indicated that instruction has been implemented successfully. It was found that pre-test and post-test was fostered with N-gain for male and female in medium category. Based on independent t test was found there was no difference improvement of decision making between male and female students. The group showed there was no difference between male group and female group, but a significant difference was noted in mix group. Students and teacher give positive response to the implementation of instruction. It is concluded that science instruction based SSI can be implemented to foster male and female decision making by forming group discussion.

Effectiveness of integrated science instructional material on pressure in daily life theme to improve digital age literacy of students

NASA Astrophysics Data System (ADS)

Asrizal; Amran, A.; Ananda, A.; Festiyed; Khairani, S.

2018-04-01

Integrated science learning and literacy skills are relevant issues in Indonesian’s education. However, the use of the integrated science learning and the integration of literacy in learning cannot be implemented well. An alternative solution of this problem is to develop integrated science instructional material on pressure in daily life theme by integrating digital age literacy. Purpose of research is to investigate the effectiveness of the use of integrated science instructional material on pressure in daily life theme to improve knowledge competence, attitudes competence and literacy skills of students. This research was a part of development research which has been conducted. In the product testing stage of this research and development was used before and after design of treatment for one sample group. Instruments to collect the data consist of learning outcomes test sheet, attitude observation sheet, and performance assessment sheet of students. Data analysis techniques include descriptive statistics analysis, normality test, homogeneity test, and paired comparison test. Therefore, the important result of research is the use of integrated science instructional material on pressure in daily life theme is effective in scientific approach to improve knowledge competence, attitudes competence, and digital age literacy skills of grade VIII students at 95% confidence level.

Metal Foam Analysis: Improving Sandwich Structure Technology for Engine Fan and Propeller Blades

NASA Technical Reports Server (NTRS)

Fedor, Jessica L.

2004-01-01

The Life Prediction Branch of the NASA Glenn Research Center is searching for ways to construct aircraft and rotorcraft engine fan and propeller blades that are lighter and less costly. One possible design is to create a sandwich structure composed of two metal faces sheets and a metal foam core. The face sheets would carry the bending loads and the foam core would have to resist the transverse shear loads. Metal foam is ideal because of its low density and energy absorption capabilities, making the structure lighter, yet still stiff. The material chosen for the face sheets and core was 17-4PH stainless steel, which is easy to make and has appealing mechanical properties. This material can be made inexpensively compared to titanium and polymer matrix composites, the two current fan blade alternatives. Initial tests were performed on design models, including vibration and stress analysis. These tests revealed that the design is competitive with existing designs; however, some problems were apparent that must be addressed before it can be implemented in new technology. The foam did not hold up as well as expected under stress. This could be due to a number of issues, but was most likely a result of a large number of pores within the steel that weakened the structure. The brazing between the face sheets and the foam was also identified as a concern. The braze did not hold up well under shear stress causing the foam to break away from the face sheets. My role in this project was to analyze different options for improving the design. I primarily spent my time examining various foam samples, created with different sintering conditions, to see which exhibited the most favorable characteristics for our purpose. Methods of analysis that I employed included examining strut integrity under a microscope, counting the number of cells per inch, measuring the density, testing the microhardness, and testing the strength under compression. Shear testing will also be done to examine the strengths of different types of brazes.

The Svalbard-Barents Sea ice-sheet - Historical, current and future perspectives

NASA Astrophysics Data System (ADS)

Ingólfsson, Ólafur; Landvik, Jon Y.

2013-03-01

The history of research on the Late Quaternary Svalbard-Barents Sea ice sheet mirrors the developments of ideas and the shifts of paradigms in glacial theory over the past 150 years. Since the onset of scientific research there in the early 19th Century, Svalbard has been a natural laboratory where ideas and concepts have been tested, and played an important (but rarely acknowledged) role in the break-through of the Ice Age theory in the 1870's. The history of how the scientific perception of the Svalbard-Barents sea ice sheet developed in the mid-20th Century also tells a story of how a combination of fairly scattered and often contradictory observational data, and through both deductive and inductive reasoning, could outline a major ice sheet that had left but few tangible fingerprints. Since the 1980's, with increased terrestrial stratigraphical data, ever more marine geological evidence and better chronological control of glacial events, our perception of the Svalbard-Barents Sea ice sheet has changed. The first reconstructions depicted it as a static, concentric, single-domed ice sheet, with ice flowing from an ice divide over the central northern Barents Sea that expanded and declined in response to large-scale, Late Quaternary climate fluctuations, and which was more or less in tune with other major Northern Hemisphere ice sheets. We now increasingly perceive it as a very dynamic, multidomed ice sheet, controlled by climate fluctuations, relative sea-level change, as well as subglacial topography, substrate properties and basal temperature. In this respect, the Svalbard-Barents Sea ice sheet will increasingly hold the key for understanding the dynamics and processes of how marine-based ice sheets build-up and decay.

Resistance spot welding of ultra-fine grained steel sheets produced by constrained groove pressing: Optimization and characterization

DOE Office of Scientific and Technical Information (OSTI.GOV)

Khodabakhshi, F.; Kazeminezhad, M., E-mail: mkazemi@sharif.edu; Kokabi, A.H.

2012-07-15

Constrained groove pressing as a severe plastic deformation method is utilized to produce ultra-fine grained low carbon steel sheets. The ultra-fine grained sheets are joined via resistance spot welding process and the characteristics of spot welds are investigated. Resistance spot welding process is optimized for welding of the sheets with different severe deformations and their results are compared with those of as-received samples. The effects of failure mode and expulsion on the performance of ultra-fine grained sheet spot welds have been investigated in the present paper and the welding current and time of resistance spot welding process according to thesemore » subjects are optimized. Failure mode and failure load obtained in tensile-shear test, microhardness, X-ray diffraction, transmission electron microscope and scanning electron microscope images have been used to describe the performance of spot welds. The region between interfacial to pullout mode transition and expulsion limit is defined as the optimum welding condition. The results show that optimum welding parameters (welding current and welding time) for ultra-fine grained sheets are shifted to lower values with respect to those for as-received specimens. In ultra-fine grained sheets, one new region is formed named recrystallized zone in addition to fusion zone, heat affected zone and base metal. It is shown that microstructures of different zones in ultra-fine grained sheets are finer than those of as-received sheets. - Highlights: Black-Right-Pointing-Pointer Resistance spot welding process is optimized for joining of UFG steel sheets. Black-Right-Pointing-Pointer Optimum welding current and time are decreased with increasing the CGP pass number. Black-Right-Pointing-Pointer Microhardness at BM, HAZ, FZ and recrystallized zone is enhanced due to CGP.« less

Porous poly(L-lactic acid) sheet prepared by stretching with starch particles as filler for tissue engineering.

PubMed

Ju, Dandan; Han, Lijing; Li, Zonglin; Chen, Yunjing; Wang, Qingjiang; Bian, Junjia; Dong, Lisong

2016-05-20

Porous poly(L-lactic acid) (PLLA) sheets were prepared by uniaxial stretching PLLA sheets containing starch filler. Here, the starch filler content, stretching ratio, stretching rate and stretching temperature are important factors to influence the structure of the porous PLLA sheets, therefore, they have been investigated in detail. The pore size distribution and tortuosity were characterized by Mercury Intrusion Porosimetry. The results revealed that the porosity and pore size enlarged with the increase of the starch filler content and stretching ratio, while shrank with the rise of stretching temperature. On the other hand, the pore structure almost had no changes with the stretching rate ranging between 5 and 40 mm/min. In order to test and verify that the porous PLLA sheet was suitable for the tissue engineering, the starch particles were removed by selective enzymatic degradation and its in vitro biocompatibility to osteoblast-like MC3T3-E1 cells was investigated. Copyright © 2016 Elsevier Ltd. All rights reserved.

The influence of heat treatment on properties of cold rolled alloyed steel and nickel superalloys sheets used in aircraft industry

NASA Astrophysics Data System (ADS)

Zaba, K.; Dul, I.; Puchlerska, S.

2017-02-01

Superalloys based on nickel and selected steels are widely used in the aerospace industry, because of their excellent mechanical properties, heat resistance and creep resistance. Metal sheets of these materials are plastically deformed and applied, inter alia, to critical components of aircraft engines. Due to their chemical composition these materials are hardly deformable. There are various methods to improve the formability of these materials, including plastic deformation at an elevated or high temperature, or a suitable heat treatment before forming process. The paper presents results of the metal sheets testing after heat treatment. For the research, sheets of two types of nickel superalloys type Inconel and of three types of steel were chosen. The materials were subjected to multivariate heat treatment at different temperature range and time. After this step, mechanical properties were examined according to the metal sheet rolling direction. The results were compared and the optimal type of pre-trial softening heat treatment for each of the materials was determined.

Test report: Electron-proton spectrometer qualification test unit, qualification test

NASA Technical Reports Server (NTRS)

Vincent, D. L.

1972-01-01

Qualification tests of the electron-proton spectrometer test unit are presented. The tests conducted were: (1) functional, (2) thermal/vacuum, (3) electromagnetic interference, (4) acoustic, (5) shock, (6) vibration, and (7) humidity. Results of each type of test are presented in the form of data sheets.

How might the North American ice sheet influence the northwestern Eurasian climate?

NASA Astrophysics Data System (ADS)

Beghin, P.; Charbit, S.; Dumas, C.; Kageyama, M.; Ritz, C.

2015-10-01

It is now widely acknowledged that past Northern Hemisphere ice sheets covering Canada and northern Europe at the Last Glacial Maximum (LGM) exerted a strong influence on climate by causing changes in atmospheric and oceanic circulations. In turn, these changes may have impacted the development of the ice sheets themselves through a combination of different feedback mechanisms. The present study is designed to investigate the potential impact of the North American ice sheet on the surface mass balance (SMB) of the Eurasian ice sheet driven by simulated changes in the past glacial atmospheric circulation. Using the LMDZ5 atmospheric circulation model, we carried out 12 experiments under constant LGM conditions for insolation, greenhouse gases and ocean. In these experiments, the Eurasian ice sheet is removed. The 12 experiments differ in the North American ice-sheet topography, ranging from a white and flat (present-day topography) ice sheet to a full-size LGM ice sheet. This experimental design allows the albedo and the topographic impacts of the North American ice sheet onto the climate to be disentangled. The results are compared to our baseline experiment where both the North American and the Eurasian ice sheets have been removed. In summer, the sole albedo effect of the American ice sheet modifies the pattern of planetary waves with respect to the no-ice-sheet case, resulting in a cooling of the northwestern Eurasian region. By contrast, the atmospheric circulation changes induced by the topography of the North American ice sheet lead to a strong decrease of this cooling. In winter, the Scandinavian and the Barents-Kara regions respond differently to the American ice-sheet albedo effect: in response to atmospheric circulation changes, Scandinavia becomes warmer and total precipitation is more abundant, whereas the Barents-Kara area becomes cooler with a decrease of convective processes, causing a decrease of total precipitation. The gradual increase of the altitude of the American ice sheet leads to less total precipitation and snowfall and to colder temperatures over both the Scandinavian and the Barents and Kara sea sectors. We then compute the resulting annual surface mass balance over the Fennoscandian region from the simulated temperature and precipitation fields used to force an ice-sheet model. It clearly appears that the SMB is dominated by the ablation signal. In response to the summer cooling induced by the American ice-sheet albedo, high positive SMB values are obtained over the Eurasian region, leading thus to the growth of an ice sheet. On the contrary, the gradual increase of the American ice-sheet altitude induces more ablation over the Eurasian sector, hence limiting the growth of Fennoscandia. To test the robustness of our results with respect to the Eurasian ice sheet state, we carried out two additional LMDZ experiments with new boundary conditions involving both the American (flat or full LGM) and high Eurasian ice sheets. The most striking result is that the Eurasian ice sheet is maintained under full-LGM North American ice-sheet conditions, but loses ~ 10 % of its mass compared to the case in which the North American ice sheet is flat. These new findings qualitatively confirm the conclusions from our first series of experiments and suggest that the development of the Eurasian ice sheet may have been slowed down by the growth of the American ice sheet, offering thereby a new understanding of the evolution of Northern Hemisphere ice sheets throughout glacial-interglacial cycles.

75 FR 24892 - Certain Coated Paper Suitable for High-Quality Print Graphics Using Sheet-Fed Presses From the...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-06

... Industry Support Calculation Coated Paper Suitable For High-Quality Print Graphics Using Sheet-Fed Presses... employs an industry-wide test to determine whether, under section 773(c)(1)(B), available information in... sections 771(33)(E) and (F) of the Act. In addition, we find that Shandong Sun Paper Industry Joint Stock...

BARBERING, A STUDY GUIDE AND PROGRESSION RECORD FOR BARBERING STUDENTS IN A COOPERATIVE TRAINING PROGRAM.

ERIC Educational Resources Information Center

Alabama Univ., University.

QUESTION-TYPE JOB OR ASSIGNMENT SHEETS IN THIS GUIDE DIRECT THE STUDENT'S RELATED STUDY IN COOPERATIVE TRAINING PROGRAMS. THE MATERIAL WAS DEVELOPED BY TRADE AND INDUSTRIAL COORDINATORS, SUBJECT MATTER SPECIALISTS, AND TEACHER EDUCATORS. IT WAS TESTED BY USE IN HIGH SCHOOL PROGRAMS. THE 61 JOB SHEETS ARE KEYED TO THREE RELATED REFERENCE BOOKS, BUT…

Hot forging of roll-cast high aluminum content magnesium alloys

NASA Astrophysics Data System (ADS)

Kishi, Tomohiro; Watari, Hisaki; Suzuki, Mayumi; Haga, Toshio

2017-10-01

This paper reports on hot forging of high aluminum content magnesium alloy sheets manufactured using horizontal twin-roll casting. AZ111 and AZ131 were applied for twin-roll casting, and a hot-forging test was performed to manufacture high-strength magnesium alloy components economically. For twin-roll casting, the casting conditions of a thick sheet for hot forging were investigated. It was found that twin-roll casting of a 10mm-thick magnesium alloy sheet was possible at a roll speed of 2.5m/min. The grain size of the cast strip was 50 to 70µm. In the hot-forging test, blank material was obtained from as-cast strip. A servo press machine with a servo die cushion was used to investigate appropriate forging conditions (e.g., temperature, forging load, and back pressure) for twin-roll casts (TRCs) AZ111 and AZ131. It was determined that high aluminum content magnesium alloy sheets manufactured using twin-roll casting could be forged with a forging load of 150t and a back pressure of 3t at 420 to 430°C. Applying back pressure during hot forging effectively forged a pin-shaped product.

49 CFR 383.131 - Test procedures.

Code of Federal Regulations, 2010 CFR

2010-10-01

... provide standardized scoring sheets for the skills tests, as well as standardized driving instructions for... 49 Transportation 5 2010-10-01 2010-10-01 false Test procedures. 383.131 Section 383.131... STANDARDS; REQUIREMENTS AND PENALTIES Tests § 383.131 Test procedures. (a) Driver information manuals...

Behavior of Steel-Sheathed Shear Walls Subjected to Seismic and Fire Loads.

PubMed

Hoehler, Matthew S; Smith, Christopher M; Hutchinson, Tara C; Wang, Xiang; Meacham, Brian J; Kamath, Praveen

2017-07-01

A series of tests was conducted on six 2.7 m × 3.7 m shear wall specimens consisting of cold-formed steel framing sheathed on one side with sheet steel adhered to gypsum board and on the opposite side with plain gypsum board. The specimens were subjected to various sequences of simulated seismic shear deformation and fire exposure to study the influence of multi-hazard interactions on the lateral load resistance of the walls. The test program was designed to complement a parallel effort at the University of California, San Diego to investigate a six-story building subjected to earthquakes and fires. The test results reported here indicate that the fire exposure caused a shift in the failure mode of the walls from local buckling of the sheet steel in cases without fire exposure, to global buckling of the sheet steel with an accompanying 35 % reduction in lateral load capacity after the wall had been exposed to fire. This behavior appears to be predictable, which is encouraging from the standpoint of residual lateral load capacity under these severe multi-hazard actions.

Student-written single-best answer questions predict performance in finals.

PubMed

Walsh, Jason; Harris, Benjamin; Tayyaba, Saadia; Harris, David; Smith, Phil

2016-10-01

Single-best answer (SBA) questions are widely used for assessment in medical schools; however, often clinical staff have neither the time nor the incentive to develop high-quality material for revision purposes. A student-led approach to producing formative SBA questions offers a potential solution. Cardiff University School of Medicine students created a bank of SBA questions through a previously described staged approach, involving student question-writing, peer-review and targeted senior clinician input. We arranged questions into discrete tests and posted these online. Student volunteer performance on these tests from the 2012/13 cohort of final-year medical students was recorded and compared with the performance of these students in medical school finals (knowledge and objective structured clinical examinations, OSCEs). In addition, we compared the performance of students that participated in question-writing groups with the performance of the rest of the cohort on the summative SBA assessment. Often clinical staff have neither the time nor the incentive to develop high-quality material for revision purposes Performance in the end-of-year summative clinical knowledge SBA paper correlated strongly with performance in the formative student-written SBA test (r = ~0.60, p <0.01). There was no significant correlation between summative OSCE scores and formative student-written SBA test scores. Students who wrote and reviewed questions scored higher than average in the end-of-year summative clinical knowledge SBA paper. Student-written SBAs predict performance in end-of-year SBA examinations, and therefore can provide a potentially valuable revision resource. There is potential for student-written questions to be incorporated into summative examinations. © 2015 John Wiley & Sons Ltd.

Characterization of Hybrid CNT Polymer Matrix Composites

NASA Technical Reports Server (NTRS)

Grimsley, Brian W.; Cano, Roberto J.; Kinney, Megan C.; Pressley, James; Sauti, Godfrey; Czabaj, Michael W.; Kim, Jae-Woo; Siochi, Emilie J.

2015-01-01

Carbon nanotubes (CNTs) have been studied extensively since their discovery and demonstrated at the nanoscale superior mechanical, electrical and thermal properties in comparison to micro and macro scale properties of conventional engineering materials. This combination of properties suggests their potential to enhance multi-functionality of composites in regions of primary structures on aerospace vehicles where lightweight materials with improved thermal and electrical conductivity are desirable. In this study, hybrid multifunctional polymer matrix composites were fabricated by interleaving layers of CNT sheets into Hexcel® IM7/8552 prepreg, a well-characterized toughened epoxy carbon fiber reinforced polymer (CFRP) composite. The resin content of these interleaved CNT sheets, as well as ply stacking location were varied to determine the effects on the electrical, thermal, and mechanical performance of the composites. The direct-current electrical conductivity of the hybrid CNT composites was characterized by in-line and Montgomery four-probe methods. For [0](sub 20) laminates containing a single layer of CNT sheet between each ply of IM7/8552, in-plane electrical conductivity of the hybrid laminate increased significantly, while in-plane thermal conductivity increased only slightly in comparison to the control IM7/8552 laminates. Photo-microscopy and short beam shear (SBS) strength tests were used to characterize the consolidation quality of the fabricated laminates. Hybrid panels fabricated without any pretreatment of the CNT sheets resulted in a SBS strength reduction of 70 percent. Aligning the tubes and pre-infusing the CNT sheets with resin significantly improved the SBS strength of the hybrid composite To determine the cause of this performance reduction, Mode I and Mode II fracture toughness of the CNT sheet to CFRP interface was characterized by double cantilever beam (DCB) and end notch flexure (ENF) testing, respectively. Results are compared to the control IM7/8552 laminate.

Role of ice sheet dynamics in the collapse of the early-Holocene Laurentide Ice Sheet

NASA Astrophysics Data System (ADS)

Matero, I. S. O.; Gregoire, L. J.; Cornford, S. L.; Ivanovic, R. F.

2017-12-01

The last stage of the deglaciation of the Laurentide Ice Sheet (LIS) during the early Holocene Thermal Maximum ( 9000 to 7000 years ago) provides an analogy and insight to the possible responses of contemporary ice sheets in a warming climate. What makes LIS particularly interesting is that meltwater from the collapse of an ice saddle over Hudson Bay was recently shown to be the primary forcing for the period of abrupt northern hemisphere cooling known as the 8.2 ka event. The evolution of the LIS during this period was likely influenced by its interaction with marginal lakes and the ocean, and its major ice stream, which exported ice towards Hudson Strait. Accurately simulating the early Holocene LIS evolution thus requires a model such as BISICLES, capable of accurately and efficiently resolving ice stream dynamics and grounding line migration thanks to the combined use of higher order physics and adaptive mesh refinement. We drive the BISICLES model using a positive degree day mass balance scheme with monthly precipitation and temperature from the HadCM3 climate model under climatic conditions from 10,000 to 8,000 years ago. We test the effect of varying the initial topographies and ice thicknesses from different timeslices in the ICE-6Gc reconstruction. We also test different parameterisations for the basal friction based on the thicknesses of the underlying sediments. These simulations evaluate the role of the Hudson Strait ice stream, ice sheet dynamics and interactions with the adjacent proglacial Lake Agassiz and North Atlantic Ocean in the collapse of the LIS. Our results highlight that the choice of parameterisation for basal friction has major effects on ice sheet dynamics and evolution.

High-resolution coupled ice sheet-ocean modeling using the POPSICLES model

NASA Astrophysics Data System (ADS)

Ng, E. G.; Martin, D. F.; Asay-Davis, X.; Price, S. F.; Collins, W.

2014-12-01

It is expected that a primary driver of future change of the Antarctic ice sheet will be changes in submarine melting driven by incursions of warm ocean water into sub-ice shelf cavities. Correctly modeling this response on a continental scale will require high-resolution modeling of the coupled ice-ocean system. We describe the computational and modeling challenges in our simulations of the full Southern Ocean coupled to a continental-scale Antarctic ice sheet model at unprecedented spatial resolutions (0.1 degree for the ocean model and adaptive mesh refinement down to 500m in the ice sheet model). The POPSICLES model couples the POP2x ocean model, a modified version of the Parallel Ocean Program (Smith and Gent, 2002), with the BISICLES ice-sheet model (Cornford et al., 2012) using a synchronous offline-coupling scheme. Part of the PISCEES SciDAC project and built on the Chombo framework, BISICLES makes use of adaptive mesh refinement to fully resolve dynamically-important regions like grounding lines and employs a momentum balance similar to the vertically-integrated formulation of Schoof and Hindmarsh (2009). Results of BISICLES simulations have compared favorably to comparable simulations with a Stokes momentum balance in both idealized tests like MISMIP3D (Pattyn et al., 2013) and realistic configurations (Favier et al. 2014). POP2x includes sub-ice-shelf circulation using partial top cells (Losch, 2008) and boundary layer physics following Holland and Jenkins (1999), Jenkins (2001), and Jenkins et al. (2010). Standalone POP2x output compares well with standard ice-ocean test cases (e.g., ISOMIP; Losch, 2008) and other continental-scale simulations and melt-rate observations (Kimura et al., 2013; Rignot et al., 2013). For the POPSICLES Antarctic-Southern Ocean simulations, ice sheet and ocean models communicate at one-month coupling intervals.

Colorectal cancer screening patient education materials-how effective is online health information?

PubMed

John, Elizabeth Sheena; John, Ann M; Hansberry, David R; Thomas, Prashant J; Agarwal, Prateek; Deitch, Christopher; Chokhavatia, Sita

2016-12-01

Patients screened for colorectal cancer (CRC) frequently turn to the Internet to improve their understanding of tests used for detection, including colonoscopy, flexible sigmoidoscopy, fecal occult blood test (FOBT), and CT colonography. It was of interest to determine the quality and readability levels of online health information. The screening tools were googled, and the top 20 results of each test were analyzed for readability, accessibility, usability, and reliability. The 80 articles excluded scientific literature and blogs. We used ten validated readability scales to measure grade levels, and one-way ANOVA and Tukey's honestly statistical different (HSD) post hoc analyses to determine any statistically significant differences among the four diagnostic tests. The LIDA tool assessed overall quality by measuring accessibility, usability, and reliability. The 80 articles were written at an 11.7 grade level, with CT colonography articles written at significantly higher levels than FOBT articles, F(3, 75) = 3.07, p = 0.033. LIDA showed moderate percentages in accessibility (83.9 %), usability (73.0 %), and reliability (75.9 %). Online health information about CRC screening tools are written at higher levels than the National Institute of Health (NIH) and American Medical Association (AMA) recommended third to seventh grade levels. More patients could benefit from this modality of information if it were written at a level and quality that would better facilitate understanding.

Construction of osteochondral-like tissue graft combining β-tricalcium phosphate block and scaffold-free centrifuged chondrocyte cell sheet.

PubMed

Niyama, Kouhei; Ide, Naoto; Onoue, Kaori; Okabe, Takahiro; Wakitani, Shigeyuki; Takagi, Mutsumi

2011-09-01

The combination of a β-tricalcium phosphate (βTCP) block with a scaffold-free chondrocyte sheet formed by the centrifugation of chondrocytes in a well was investigated with the aim of constructing an osteochondral-like structure. Human and porcine articular cartilage chondrocytes were respectively centrifuged in a 96-well plate or cell culture insert (0.32 cm(2)) that was set in a 24-well plate, cultivated in the respective vessel for 3 weeks, and the cell sheets were harvested. In some cases, a cylindrical βTCP block (diameter 5 mm, height 3 mm) was placed on the sheet on days 1-7. The sheet size, cell number, and sulfated glycosaminoglycan accumulation were determined. The use of a 96-well plate for not suspension but adhesion culture and the initial centrifugation of a well containing cells were crucial to obtaining a uniformly thick cell sheet. The glycosaminoglycan density of the harvested cell sheet was comparable to that of the pellet culture. An inoculum cell number of more than 31 × 10(5) cells tended to result in a curved cell sheet. Culture involving 18.6 × 10(5) cells and the 96-well plate for adhesion culture showed no curving of the cell sheet (thickness of 0.85 mm), and these were found to be the best of the culture conditions tested. The timing of the addition of a βTCP block to the cell sheet (1-7 days) markedly affected the balance between the thickness of cell sheet parts on and in the βTCP block. Centrifugation and subsequent cultivation of chondrocytes (18.6 × 10(5) cells) in a 96-well plate for adhesion culture led to the production of a scaffold-free cartilage-like cell sheet with a thickness of 0.85 mm. A combined osteochondral-like structure was produced by putting a βTCP block on the cell sheet. The thickness of the cell sheet on the βTCP block and the binding strength between the cell sheet and the βTCP block could be optimized by adjusting the inoculum cell number and timing of βTCP block addition.

LSP Composite Test Bed Design

NASA Technical Reports Server (NTRS)

Day, Arthur C.; Griess, Kenneth H.

2013-01-01

This document provides standalone information for the Lightning Strike Protection (LSP) Composite Substrate Test Bed Design. A six-sheet drawing set is reproduced for reference, as is some additional descriptive information on suitable sensors and use of the test bed.

RDI Task Final Report of Research and Development of Software, Ballistic Test Site Terminal.

DTIC Science & Technology

1984-01-01

Vf’~~.Veb . 6* U- .~ .. A0A$i 9.NrtY% . . APPENDIX P -SUBROUTINE DESCRIPTIONS FORTRAN callable subprograms written in FORTRAN. ANSWR DELAY LABL RPTER...CKOVL IYT2 RDNAR WSCNR CLEAR JBCD RDVM ZERO CNTRL JDATA REVNT ZSPLN FORTRAN callable subprograms written in assembler IASRD IOPSY NCKT -p- w...u *p* * * FORTRAN CALLABLE SUBPROGRAMS WRITTEN IN FORTRAN SUBROUTINE ANSWR(LU,KDEV, ICODE, IENTRY,RVAL, IVAL), REV*C 04DEC83 $ CLF

Transplantation of periodontal ligament cell sheets expressing human β-defensin-3 promotes anti-inflammation in a canine model of periodontitis

PubMed Central

Zhu, Minwen; Miao, Bo; Zhu, Jianhua; Wang, Haiyan; Zhou, Zengtong

2017-01-01

Periodontitis is a chronic oral inflammatory disease caused by microorganisms. Human β-defensin-3 (HBD-3) is an endogenous antimicrobial peptide that inhibits a broad spectrum of microorganisms. Cell sheet technology has been widely applied in tissue and organ reconstructions. In the current study, it was aimed to investigate the anti-inflammatory effect of periodontal tissue engineered by HBD-3 gene-modified periodontal ligament cell (PDLC) sheets, and to identify a suitable method of promoting the regeneration of periodontal tissues. Western blot analysis and antimicrobial tests were used to confirm the expression of HBD-3. The effect of the cell sheets on anti-inflammatory activity and bone remodeling in a dog model of periodontitis was demonstrated by immunohistochemistry. The results demonstrated that the transfected PDLCs stably expressed HBD-3. Periodontal pathogens were susceptible to the antimicrobial activity of the cell sheets. In addition, the cell sheets relieved the bone resorption caused by inflammation in the in vivo model. HBD-3 may potentially be applied in the treatment of periodontitis and may function as osteogenic promoter via its anti-inflammatory effect. PMID:28944821

Transplantation of periodontal ligament cell sheets expressing human β‑defensin‑3 promotes anti‑inflammation in a canine model of periodontitis.

PubMed

Zhu, Minwen; Miao, Bo; Zhu, Jianhua; Wang, Haiyan; Zhou, Zengtong

2017-11-01

Periodontitis is a chronic oral inflammatory disease caused by microorganisms. Human β‑defensin‑3 (HBD‑3) is an endogenous antimicrobial peptide that inhibits a broad spectrum of microorganisms. Cell sheet technology has been widely applied in tissue and organ reconstructions. In the current study, it was aimed to investigate the anti‑inflammatory effect of periodontal tissue engineered by HBD‑3 gene‑modified periodontal ligament cell (PDLC) sheets, and to identify a suitable method of promoting the regeneration of periodontal tissues. Western blot analysis and antimicrobial tests were used to confirm the expression of HBD‑3. The effect of the cell sheets on anti‑inflammatory activity and bone remodeling in a dog model of periodontitis was demonstrated by immunohistochemistry. The results demonstrated that the transfected PDLCs stably expressed HBD‑3. Periodontal pathogens were susceptible to the antimicrobial activity of the cell sheets. In addition, the cell sheets relieved the bone resorption caused by inflammation in the in vivo model. HBD‑3 may potentially be applied in the treatment of periodontitis and may function as osteogenic promoter via its anti‑inflammatory effect.

Magnetic grain-size variations through an ash flow sheet: influence on magnetic properties and implications for cooling history

USGS Publications Warehouse

Rosenbaum, J.G.

1993-01-01

Rock magnetic studies of tuffs are essential to the interpretation of paleomagnetic data derived from such rocks, provide a basis for interpretation of aeromagnetic data over volcanic terranes, and yield insights into the depositional and cooling histories of ash flow sheets. A rhyolitic ash flow sheet, the Miocene-aged Tiva Canyon Member of the Paintbrush Tuff, contains both titanomagnetite phenocrysts, present in the magma prior to eruption, and cubic Fe-oxide microcrystals that grew after emplacement. Systematic variations in the quantity and magnetic grain size of the microcrystals produce large variations in magnetic properties through a section of the ash flow sheet penetrated in a borehole on the Nevada Test Site. Microcrystals are important contributors to remanent magnetization and magnetic susceptibility in two 15-m-thick zones at the top and bottom. Within these zones the size of microcrystals decreases both toward the quenched margins and toward the interior of the sheet. The decrease in microcrystal size toward the interior of the sheet is interpreted to indicate the presence of a cooling break; possibly represented by a concentration of pumice. -from Author

Handwriting features of children with developmental coordination disorder--results of triangular evaluation.

PubMed

Rosenblum, Sara; Margieh, Jumana Aassy; Engel-Yeger, Batya

2013-11-01

Developmental coordination disorders (DCD) is one of the most common disorders affecting school-aged children. The study aimed to characterize the handwriting performance of children with DCD who write in Arabic, based on triangular evaluation. Participants included 58 children aged 11-12 years, 29 diagnosed with DCD based on the DSM-IV criteria and the M-ABC, and 29 matched typically developed controls. Children were asked to copy a paragraph on a sheet of paper affixed to a digitizer supplying objective measures of the handwriting process. The handwriting proficiency screening questionnaire (HPSQ) was completed by their teachers while observing their performance and followed by evaluation of their final written product. Results indicated that compared to controls, children with DCD required significantly more on-paper and in-air time per stroke while copying. In addition, global legibility, unrecognizable letters and spatial arrangement measures of their written product were significantly inferior. Significant group differences were also found between the HPSQ subscales scores. Furthermore, 82.8% of all participants were correctly classified into groups based on one discriminate function which included two handwriting performance measures. These study results strongly propose application of triangular standardized evaluation to receive better insight of handwriting deficit features of individual children with DCD who write in Arabic. Copyright © 2013 Elsevier Ltd. All rights reserved.

Preparation of Graphene Sheets by Electrochemical Exfoliation of Graphite in Confined Space and Their Application in Transparent Conductive Films.

PubMed

Wang, Hui; Wei, Can; Zhu, Kaiyi; Zhang, Yu; Gong, Chunhong; Guo, Jianhui; Zhang, Jiwei; Yu, Laigui; Zhang, Jingwei

2017-10-04

A novel electrochemical exfoliation mode was established to prepare graphene sheets efficiently with potential applications in transparent conductive films. The graphite electrode was coated with paraffin to keep the electrochemical exfoliation in confined space in the presence of concentrated sodium hydroxide as the electrolyte, yielding ∼100% low-defect (the D band to G band intensity ratio, I D /I G = 0.26) graphene sheets. Furthermore, ozone was first detected with ozone test strips, and the effect of ozone on the exfoliation of graphite foil and the microstructure of the as-prepared graphene sheets was investigated. Findings indicate that upon applying a low voltage (3 V) on the graphite foil partially coated with paraffin wax that the coating can prevent the insufficiently intercalated graphite sheets from prematurely peeling off from the graphite electrode thereby affording few-layer (<5 layers) holey graphene sheets in a yield of as much as 60%. Besides, the ozone generated during the electrochemical exfoliation process plays a crucial role in the exfoliation of graphite, and the amount of defect in the as-prepared graphene sheets is dependent on electrolytic potential and electrode distance. Moreover, the graphene-based transparent conductive films prepared by simple modified vacuum filtration exhibit an excellent transparency and a low sheet resistance after being treated with NH 4 NO 3 and annealing (∼1.21 kΩ/□ at ∼72.4% transmittance).

Hydraulic properties for interrill erosion on steep slopes using a portable rainfall simulator

NASA Astrophysics Data System (ADS)

Shin, Seung Sook; Hwang, Yoonhee; Deog Park, Sang; Yun, Minu; Park, Sangyeon

2017-04-01

The hydraulic parameters for sheet flow on steep slopes have been not frequently measured because the shallow flow depth and slow flow velocity are difficult to measure. In this study hydraulic values of sheet flow were analyzed to evaluate interrill erosion on steep slopes. A portable rainfall simulator was used to conduct interrill erosion test. The kinetic energy of rainfall simulator was obtained by disdrometer being capable of measuring the drop size distribution and velocity of falling raindrops. The sheet flow velocity was determined by the taken time for a dye transferring fixed points using video images. Surface runoff discharge and sediment yield increased with increase of rainfall intensity and kinetic energy and slope steepness. Especially sediment yield was strongly correlated with sheet flow velocity. The maximum velocity of sheet flow was 2.3cm/s under rainfall intensity of 126.8mm/h and slope steepness of 53.2%. The sheet flow was laminar and subcritical flow as the flow Reynolds number and Froude number are respectively the ranges of 10 22 and 0.05 0.25. The roughness coefficient (Manning's n) for sheet flow on steep slopes was relatively large compared to them on the gentle slope. Keywords: Sheet flow velocity; Rainfall simulator; Interrill erosion; Steep slope This work was supported by the National Research Foundation of Korea(NRF) grant funded by the Korea government(MSIP) (No. 2015R1C1A2A01055469).

Actuating materials. Voxelated liquid crystal elastomers.

PubMed

Ware, Taylor H; McConney, Michael E; Wie, Jeong Jae; Tondiglia, Vincent P; White, Timothy J

2015-02-27

Dynamic control of shape can bring multifunctionality to devices. Soft materials capable of programmable shape change require localized control of the magnitude and directionality of a mechanical response. We report the preparation of soft, ordered materials referred to as liquid crystal elastomers. The direction of molecular order, known as the director, is written within local volume elements (voxels) as small as 0.0005 cubic millimeters. Locally, the director controls the inherent mechanical response (55% strain) within the material. In monoliths with spatially patterned director, thermal or chemical stimuli transform flat sheets into three-dimensional objects through controlled bending and stretching. The programmable mechanical response of these materials could yield monolithic multifunctional devices or serve as reconfigurable substrates for flexible devices in aerospace, medicine, or consumer goods. Copyright © 2015, American Association for the Advancement of Science.

Further results from PIXE analysis of inks in Galileo's notes on motion

NASA Astrophysics Data System (ADS)

Del Carmine, P.; Giuntini, L.; Hooper, W.; Lucarelli, F.; Mandò, P. A.

1996-06-01

We have recently analysed the inks in some of the folios of Vol. 72 of Manoscritti galileiani, kept at the Biblioteca Nazionale Centrale di Firenze, which contains a collection of loose handwritten sheets containing undated notes, data from experiments and propositions on the problems of motion from different periods of Galileo's life. This paper reports specific results obtained from the analysis of some of these propositions, which allowed to make a contribution to their chronological attribution and therefore to the solution of some historical controversies. Even in the case where the "absolute" chronological attributions could not be made on the basis of comparison with dated documents, the PIXE results provided useful information to deny or confirm the hypothesis that different propositions were written in the same or in different periods.

Development of a Thin Film Primary Surface Heat Exchanger for Advanced Power Cycles

DOE Office of Scientific and Technical Information (OSTI.GOV)

Allison, Tim; Beck, Griffin; Bennett, Jeffrey

This project objective is to develop a high-temperature design upgrade for an existing primary surface heat exchanger so that the redesigned hardware is capable of operation in CO 2 at temperatures up to 1,510°F (821°C) and pressure differentials up to 130 psi (9 bar). The heat exchanger is proposed for use as a recuperator in an advanced low-pressure oxy-fuel Brayton cycle that is predicted to achieve over 50% thermodynamic efficiency, although the heat exchanger could also be used in other high-temperature, low-differential pressure cycles. This report describes the progress to date, which includes continuing work performed to select and testmore » new candidate materials for the recuperator redesign, final mechanical and thermal performance analysis results of various redesign concepts, and the preliminary design of a test loop for the redesigned recuperator including a budgetary estimate for detailed test loop design, procurement, and test operation. A materials search was performed in order to investigate high-temperature properties of many candidate materials, including high-temperature strength and nickel content. These properties were used to rank the candidate materials, resulting in a reduced list of nine materials for corrosion testing. Multiple test rigs were considered and analyzed for short-term corrosion testing and Thermal Gravimetric Analysis (TGA) was selected as the most cost-effective option for evaluating corrosion resistance of the candidate materials. In addition, tantalum, niobium, and chromium coatings were identified as potential options for increased corrosion resistance. The test results show that many materials exhibit relatively low weight gain rates, and that niobium and tantalum coatings may improve corrosion resistance for many materials, while chromium coatings appear to oxidize and debond quickly. Metallurgical analysis of alloys was also performed, showing evidence of intergranular attack in 282 that may cause long-term reliability problems in CO 2 service at these temperatures. However, long-term testing in a flowing environment is recommended in order to understand accurately the severity of the attack. Detailed economic modeling of the existing air cycle recuperator and CO 2 cycle recuperator options was also completed, including costs for material, fabrication, fuel, maintenance, and operation. The analysis results show that the increased capital cost for high-temperature materials may be offset by higher cycle efficiencies, decreasing the overall lifetime cost of the system. The economic analysis also examines costs associated with increased pressure drop and material changes for two redesign options. These results show that, even with slightly reduced performance and/or higher material costs, the lifetime cost per energy production may still be reduced by over 12%. The existing recuperator design information was provided by Solar Turbines, Inc. via several models, drawings, and design handoff meetings. Multiple fluid/thermal and structural models were created in order to analyze critical recuperator performance and mechanical strength in critical areas throughout the redesign process. These models were analyzed for a baseline condition (consistent with current Mercury 50 operation) for validation purposes. Results are presented for heat transfer coefficients and pressure drops, matching well with the existing operational data. Simulation of higher-temperature CO 2 conditions was also performed, showing a slight expected increase in both heat transfer and pressure drop. Mechanical analysis results for critical areas on the cross-flow and counter-flow sheets have also been obtained for air and CO 2 cases. These results show similar stresses in both cases but significantly reduced safety factors for the CO 2 case due to reduced yield and creep rupture strengths of alloy 625 at the higher temperatures. A concept brainstorm session and initial down-selection were completed in order to identify promising redesign options for further analysis. Detailed analysis of all promising redesign options was performed via finite element and computational fluid dynamic simulations in order to characterize mechanical and thermal-fluid performance of each option. These options included material change, various sheet thickness configurations, pitch and phasing of cross-flow and counter-flow sheets, and separator sheets. The analysis results have identified two viable redesign options that maintain existing safety margins optimally through a material change to Haynes 282 and (A) sheet thickness increases of 40% on the counter-flow sheet and 75% on the hot side cross-flow corrugation sheet or (B) addition of a separator sheet in the counter-flow section while maintaining the original counter-flow sheet thickness and increasing the cross-flow corrugation sheet thickness by 90% to account for the increase in cell height. While both options satisfy mechanical stress constraints, the separator sheet design has a higher part count, slightly reduced heat transfer, and slightly higher pressure drop than the first option and is not preferred. Finally, several test loop concepts have been developed for different full-scale and reduced-scale recuperator testing options. For each option, various loop components, such as heat exchangers, valves, heaters, and compressors, were evaluated in an effort to maximize utilization of existing resources. All concepts utilize an existing 3-MW CO 2 compressor, heater, and loop coolers, but the concepts vary by incorporating different amounts of new equipment for achieving various flow rates (all concepts operate at design pressure and temperature). The third concept achieves a 1 kg/s test without purchasing any costly equipment (coolers, heaters, blowers, etc.). Since the stacked cell design of the recuperator results in the same flow conditions at each core cell (even for a reduced-scale test). Thus, test loop Concept #3 was selected for the preliminary design. This loop design is detailed within the report, culminating in a budgetary estimate of $1,013,000.00 for the detailed design, construction, commissioning, and operation of a high-temperature recuperator test loop.« less

Single point incremental forming: Formability of PC sheets

NASA Astrophysics Data System (ADS)

Formisano, A.; Boccarusso, L.; Carrino, L.; Lambiase, F.; Minutolo, F. Memola Capece

2018-05-01

Recent research on Single Point Incremental Forming of polymers has slightly covered the possibility of expanding the materials capability window of this flexible forming process beyond metals, by demonstrating the workability of thermoplastic polymers at room temperature. Given the different behaviour of polymers compared to metals, different aspects need to be deepened to better understand the behaviour of these materials when incrementally formed. Thus, the aim of the work is to investigate the formability of incrementally formed polycarbonate thin sheets. To this end, an experimental investigation at room temperature was conducted involving formability tests; varying wall angle cone and pyramid frusta were manufactured by processing polycarbonate sheets with different thicknesses and using tools with different diameters, in order to draw conclusions on the formability of polymer sheets through the evaluation of the forming angles and the observation of the failure mechanisms.

Comparison of bursting pressure results of LPG tank using experimental and finite element method.

PubMed

Aksoley, M Egemen; Ozcelik, Babur; Bican, Ismail

2008-03-01

In this study, the resistance of liquefied-petroleum gas (LPG) tanks produced from carbon steel sheet metal of different thicknesses has been investigated by bursting pressure experiments and non-linear Finite Element Method (FEM) method by increasing internal pressure values. The designs of LPG tanks produced from sheet metal to be used at the study have been realized by analytical calculations made taking into consideration of related standards. Bursting pressure tests have been performed that were inclined to decreasing the sheet thickness of LPG tanks used in industry. It has been shown that the LPG tanks can be produced in compliance with the standards when the sheet thickness is lowered from 3 to 2.8mm. The FEM results have displayed close values with the bursting results obtained from the experiments.

Laboratory Evaluation of a Colorimetric Hydrazine Dosimeter

DTIC Science & Technology

1990-06-12

4.5 4.5 4 4.3 012 3 3.5 4 3.5 4 4.5 4.5 4.3 59456 014 5 5 5 5.0 5 5.5 5 5.2 014 5.5 6 5 5.5 6 6 6 6.0 GMO COLOR BADGE LOG SHEET TEST 30 1.0. BADGE...3 3.5 3.3 38959 CON .164 0 1.5 1.5 1.5 2 2 2.0 2 2 2.0 2 2 2.0 GMO COLOR BADGE LOG SHEET TEST 84 I.D. BADGE DATE INTER- MMH TIME DOSE RH TEMP POST

House Dust Mite Prevalence in the House of Patients with Atopic Dermatitis in Mashhad, Iran

PubMed Central

Ziyaei, Toktam; Berenji, Fariba; Jabbari-Azad, Farahzad; Fata, Abdolmajid; Jarahi, Lida; Fereidouni, Mohammad

2017-01-01

Background: Being exposed to house dust mites intensifies atopic dermatitis. This study has investigated the contamination rate with Dermatophagoides mites in patient’s residential home with atopic dermatitis. Methods: In this cross-sectional study, 40 patients took part with atopic dermatitis (positive or negative for mites by prick Dermal Test). Samples were collected from 3 locations (living room, bedroom and bed) by vacuum cleaner. Dust samples (transferred to freezer −20 °C) were examined by direct method and flotation. The data were analyzed using statistical SPSS vr.20 software. Results: Twenty patients of positive prick test included 8 (40%) male and 12 (60%) female. The results of direct observation of mites: 7 cases (35%) in bedding sheets, 6 cases (30%) bedrooms’ carpet, 3 cases (15%) living room’s carpet. Twenty patients of negative prick test included 8 (40%) male and 12 (60%) female. Only mites were found (5%) in living room’s carpets of negative prick test patients. Dermatophagoides pteronyssinus was more frequent than Dermatophagoides farinae. (98% vs 83%). Conclusion: Fifty-five percent of residential homes of prick test positive patients and only 5% of residential homes of prick test negative patients were positive for mite. Sunshine provided home had fewer mites than home where sunshine is not provided. Prick test positive patients used handmade carpets more than machine made ones. In positive prick test patients, mites were found in bed sheet and bedroom’s carpet more than negative prick test patient’s sheets and carpets. PMID:29062855

Analysis and comparison of magnetic sheet insulation tests

NASA Astrophysics Data System (ADS)

Marion-Péra, M. C.; Kedous-Lebouc, A.; Cornut, B.; Brissonneau, P.

1994-05-01

Magnetic circuits of electrical machines are divided into coated sheets in order to limit eddy currents. The surface insulation resistance of magnetic sheets is difficult to evaluate because it depends on parameters like pressure and covers a wide range of values. Two methods of measuring insulation resistance are analyzed: the standardized 'Franklin device' and a tester developed by British Steel Electrical. Their main drawback is poor local repeatability. The Franklin method allows better quality control of industrial process because it measures only one insulating layer at a time. It also gives more accurate images of the distribution of possible defects. Nevertheless, both methods lead to similar classifications of insulation efficiency.

Planning Multisentential English Text Using Communicative Acts

DTIC Science & Technology

1990-12-01

bowl. Add the flour and the baking soda. Stir in the chocolate pieces. Grease a cookie sheet. Spoon the cookie dough onto the cookie sheet. Bake it at...Chocolate Chip Cookies ......................................................................................... 185 Figure 6.5 identify-location Plan...34), and recurses on subactions as required. The plan operators of Figures 6.1 and 6.3 were tested with a small knowledge base of cookie recipe

Diary of an astronaut: examination of the remains of the late Israeli astronaut Colonel Ilan Ramon's Crew Notebook recovered after the loss of NASA's space shuttle Columbia.

PubMed

Brown, Sharon; Sin-David, Laser

2007-05-01

Two months after the fatal re-entering into the Earth's atmosphere of Columbia flight STS-107, the remains of Israeli astronaut Colonel Ilan Ramon's Crew Notebook were found strewn in a field in San Augustine County, TX. The random pile of papers was found to have survived the calamity of the Shuttle's disintegration remarkably well. Most of the papers recovered were torn and/or washed out to varying degrees but only mildly charred around the edges. The sheets of paper could be categorized into four groups: Group I: eight sides of paper written while in space in black ink and in pencil--Ramon's personal diary; the writing on these eight sides of paper survived well and is only missing where the pages were torn. Small fragments found in the field were physically matched to holes in the pages thus locating their original positions in the text. Group II: six sides of technical preparation notes written by Ramon before the mission. The writing on these pages was washed out entirely, but much of it was visualized using infrared luminescence. Group III: eight sides of personal notes prepared by Ramon before the mission written in blue ink. The writing on these pages was barely visible to the naked eye and not visualized by infrared luminescence, but was made largely legible by digital enhancement imaging. Group IV: a few sides of printed technical information. These pages were mostly intact and were not examined at length as they contained standard printed material. After completion of examinations at the Questioned Document Laboratory of the Israel Police, the diary was transferred to the Paper Conservation Department of the Israel Museum for preservation and strengthening treatments.

Nursing mathematics: the importance of application.

PubMed

Hutton, B M

This study explores the effectiveness of a revision programme in nursing mathematics for student nurses. Students who took the revision programme achieved a marked improvement in test results, although some still scored low in written tests. When interviewed, the students reported that they had difficulty applying written work in the classroom to actual calculations in the workplace. They found that only by 'doing' mathematics did the theory make sense. The author recommends that students should be encouraged to maximise the opportunities to practise mathematics in the clinical setting.

49 CFR 383.131 - Test manuals.

Code of Federal Regulations, 2012 CFR

2012-10-01

...; (ix) Causes for automatic failure of skills tests; (x) Standardized scoring sheets for the skills tests; and (xi) Standardized driving instructions for the applicants. (2) A State may include any... 49 Transportation 5 2012-10-01 2012-10-01 false Test manuals. 383.131 Section 383.131...

A pilot study of simple interventions to improve informed consent in clinical research: feasibility, approach, and results.

PubMed

Kass, Nancy E; Taylor, Holly A; Ali, Joseph; Hallez, Kristina; Chaisson, Lelia

2015-02-01

Research suggests that participants do not always adequately understand studies. While some consent interventions increase understanding, methodologic challenges have been raised in studying consent outside of actual trial settings. This study examined the feasibility of testing two consent interventions in actual studies and measured effectiveness of interventions in improving understanding. Participants enrolling in any of eight ongoing clinical trials were sequentially assigned to one of three different informed consent strategies for enrollment in their clinical trial. Control participants received standard consent procedures for their trial. Participants in the first intervention arm received a bulleted fact sheet summarizing key study information. Participants in the second intervention arm received the bulleted fact sheet and also engaged in a feedback Q&A session. Later, patients answered closed- and open-ended questions to assess patient understanding and literacy. Descriptive statistics, Wilcoxon -Mann -Whitney and Kruskal-Wallis tests were generated to assess correlations; regression analysis determined predictors of understanding. 144 participants enrolled. Using regression analysis, participants receiving the second intervention scored 7.6 percentage points higher (p = .02) on open-ended questions about understanding than participants in the control, although unadjusted comparisons did not reach statistical significance. Our study supports the hypothesis that patients receiving both bulleted fact sheets and a Q&A session had higher understanding compared to standard consent. Fact sheets and short structured dialog are quick to administer and easy to replicate across studies and should be tested in larger samples. © The Author(s) 2014.

A Modified Johnson-Cook Model for Sheet Metal Forming at Elevated Temperatures and Its Application for Cooled Stress-Strain Curve and Spring-Back Prediction

NASA Astrophysics Data System (ADS)

Duc-Toan, Nguyen; Tien-Long, Banh; Young-Suk, Kim; Dong-Won, Jung

2011-08-01

In this study, a modified Johnson-Cook (J-C) model and an innovated method to determine (J-C) material parameters are proposed to predict more correctly stress-strain curve for tensile tests in elevated temperatures. A MATLAB tool is used to determine material parameters by fitting a curve to follow Ludwick's hardening law at various elevated temperatures. Those hardening law parameters are then utilized to determine modified (J-C) model material parameters. The modified (J-C) model shows the better prediction compared to the conventional one. As the first verification, an FEM tensile test simulation based on the isotropic hardening model for boron sheet steel at elevated temperatures was carried out via a user-material subroutine, using an explicit finite element code, and compared with the measurements. The temperature decrease of all elements due to the air cooling process was then calculated when considering the modified (J-C) model and coded to VUMAT subroutine for tensile test simulation of cooling process. The modified (J-C) model showed the good agreement between the simulation results and the corresponding experiments. The second investigation was applied for V-bending spring-back prediction of magnesium alloy sheets at elevated temperatures. Here, the combination of proposed J-C model with modified hardening law considering the unusual plastic behaviour for magnesium alloy sheet was adopted for FEM simulation of V-bending spring-back prediction and shown the good comparability with corresponding experiments.

The structural behavior of a graphite-polymide honeycomb sandwich panel with quasi-isotropic face sheets and an orthotropic core

NASA Technical Reports Server (NTRS)

Hyer, M. W.; Hagaman, J. A.

1979-01-01

The results of a series of tests of graphite-polyimide honeycomb sandwich panels are presented. The panels were 1.22 m long, 0.508 m wide, and approximately 13.3 m thick. The face sheets were a T-300/PMR-15 fabric in a quasi-isotropic layup and were 0.279 mm thick. The core was Hexcel HRH 327-3/16 - 4.0 glass reinforced polyimide honeycomb, 12.7 mm thick. Three panels were used in the test: one was cut into smaller pieces for testing as beam, compression, and shear specimens; a second panel was used for plate bending tests; the third panel was used for in-plane stability tests. Presented are the experimental results of four point bending tests, short block compression tests, core transverse shear modulus, three point bending tests, vibration tests, plate bending tests, and panel stability tests. The results of the first three tests are used to predict the results of some of the other tests. The predictions and experimental results are compared, and the agreement is quite good.

Particle Acceleration and Heating by Turbulent Reconnection

NASA Astrophysics Data System (ADS)

Vlahos, Loukas; Pisokas, Theophilos; Isliker, Heinz; Tsiolis, Vassilis; Anastasiadis, Anastasios

2016-08-01

Turbulent flows in the solar wind, large-scale current sheets, multiple current sheets, and shock waves lead to the formation of environments in which a dense network of current sheets is established and sustains “turbulent reconnection.” We constructed a 2D grid on which a number of randomly chosen grid points are acting as scatterers (I.e., magnetic clouds or current sheets). Our goal is to examine how test particles respond inside this large-scale collection of scatterers. We study the energy gain of individual particles, the evolution of their energy distribution, and their escape time distribution. We have developed a new method to estimate the transport coefficients from the dynamics of the interaction of the particles with the scatterers. Replacing the “magnetic clouds” with current sheets, we have proven that the energization processes can be more efficient depending on the strength of the effective electric fields inside the current sheets and their statistical properties. Using the estimated transport coefficients and solving the Fokker-Planck (FP) equation, we can recover the energy distribution of the particles only for the stochastic Fermi process. We have shown that the evolution of the particles inside a turbulent reconnecting volume is not a solution of the FP equation, since the interaction of the particles with the current sheets is “anomalous,” in contrast to the case of the second-order Fermi process.

Fabrication of Hadfield-Cored Multi-layer Steel Sheet by Roll-Bonding with 1.8-GPa-Strength-Grade Hot-Press-Forming Steel

NASA Astrophysics Data System (ADS)

Chin, Kwang-Geun; Kang, Chung-Yun; Park, Jaeyeong; Lee, Sunghak

2018-03-01

An austenitic Hadfield steel was roll-bonded with a 1.8-GPa-strength-grade martensitic hot-press-forming (HPF) steel to fabricate a multi-layer steel (MLS) sheet. Near the Hadfield/HPF interface, the carburized and decarburized layers were formed by the carbon diffusion from the Hadfield (1.2%C) to HPF (0.35%C) layers, and could be regarded as kinds of very thin multi-layers of 35 μm in thickness. The tensile test and fractographic data indicated that the MLS sheet was fractured abruptly within the elastic range by the intergranular fracture occurred in the carburized layer. This was because C was mainly segregated at prior austenite grain boundaries in the carburized layer, which weakened grain boundaries to induce the intergranular fracture. In order to solve the intergranular facture problem, the MLS sheet was tempered at 200 °C. The stress-strain curve of the tempered MLS sheet lay between those of the HPF and Hadfield sheets, and a rule of mixtures was roughly satisfied. Tensile properties of the MLS sheet were dramatically improved after the tempering, and the intergranular fracture was erased completely. In particular, the yield strength up to 1073 MPa along with the high strain hardening and excellent ductility of 32.4% were outstanding because the yield strength over 1 GPa was hardly achieved in conventional austenitic steels.

PARTICLE ACCELERATION AND HEATING BY TURBULENT RECONNECTION

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vlahos, Loukas; Pisokas, Theophilos; Isliker, Heinz

2016-08-10

Turbulent flows in the solar wind, large-scale current sheets, multiple current sheets, and shock waves lead to the formation of environments in which a dense network of current sheets is established and sustains “turbulent reconnection.” We constructed a 2D grid on which a number of randomly chosen grid points are acting as scatterers (i.e., magnetic clouds or current sheets). Our goal is to examine how test particles respond inside this large-scale collection of scatterers. We study the energy gain of individual particles, the evolution of their energy distribution, and their escape time distribution. We have developed a new method tomore » estimate the transport coefficients from the dynamics of the interaction of the particles with the scatterers. Replacing the “magnetic clouds” with current sheets, we have proven that the energization processes can be more efficient depending on the strength of the effective electric fields inside the current sheets and their statistical properties. Using the estimated transport coefficients and solving the Fokker–Planck (FP) equation, we can recover the energy distribution of the particles only for the stochastic Fermi process. We have shown that the evolution of the particles inside a turbulent reconnecting volume is not a solution of the FP equation, since the interaction of the particles with the current sheets is “anomalous,” in contrast to the case of the second-order Fermi process.« less

Fabrication of Hadfield-Cored Multi-layer Steel Sheet by Roll-Bonding with 1.8-GPa-Strength-Grade Hot-Press-Forming Steel

NASA Astrophysics Data System (ADS)

Chin, Kwang-Geun; Kang, Chung-Yun; Park, Jaeyeong; Lee, Sunghak

2018-05-01

An austenitic Hadfield steel was roll-bonded with a 1.8-GPa-strength-grade martensitic hot-press-forming (HPF) steel to fabricate a multi-layer steel (MLS) sheet. Near the Hadfield/HPF interface, the carburized and decarburized layers were formed by the carbon diffusion from the Hadfield (1.2%C) to HPF (0.35%C) layers, and could be regarded as kinds of very thin multi-layers of 35 μm in thickness. The tensile test and fractographic data indicated that the MLS sheet was fractured abruptly within the elastic range by the intergranular fracture occurred in the carburized layer. This was because C was mainly segregated at prior austenite grain boundaries in the carburized layer, which weakened grain boundaries to induce the intergranular fracture. In order to solve the intergranular facture problem, the MLS sheet was tempered at 200 °C. The stress-strain curve of the tempered MLS sheet lay between those of the HPF and Hadfield sheets, and a rule of mixtures was roughly satisfied. Tensile properties of the MLS sheet were dramatically improved after the tempering, and the intergranular fracture was erased completely. In particular, the yield strength up to 1073 MPa along with the high strain hardening and excellent ductility of 32.4% were outstanding because the yield strength over 1 GPa was hardly achieved in conventional austenitic steels.

Sequence specificity, statistical potentials, and three-dimensional structure prediction with self-correcting distance geometry calculations of beta-sheet formation in proteins.

PubMed Central

Zhu, H.; Braun, W.

1999-01-01

A statistical analysis of a representative data set of 169 known protein structures was used to analyze the specificity of residue interactions between spatial neighboring strands in beta-sheets. Pairwise potentials were derived from the frequency of residue pairs in nearest contact, second nearest and third nearest contacts across neighboring beta-strands compared to the expected frequency of residue pairs in a random model. A pseudo-energy function based on these statistical pairwise potentials recognized native beta-sheets among possible alternative pairings. The native pairing was found within the three lowest energies in 73% of the cases in the training data set and in 63% of beta-sheets in a test data set of 67 proteins, which were not part of the training set. The energy function was also used to detect tripeptides, which occur frequently in beta-sheets of native proteins. The majority of native partners of tripeptides were distributed in a low energy range. Self-correcting distance geometry (SECODG) calculations using distance constraints sets derived from possible low energy pairing of beta-strands uniquely identified the native pairing of the beta-sheet in pancreatic trypsin inhibitor (BPTI). These results will be useful for predicting the structure of proteins from their amino acid sequence as well as for the design of proteins containing beta-sheets. PMID:10048326

Microstructure, Mechanical Properties, and Flatness of SEBM Ti-6Al-4V Sheet in As-Built and Hot Isostatically Pressed Conditions

NASA Astrophysics Data System (ADS)

Tang, H. P.; Wang, J.; Song, C. N.; Liu, N.; Jia, L.; Elambasseril, J.; Qian, M.

2017-03-01

Sheet (0.41-4.80 mm thick) or thin plate structures commonly exist in additively manufactured Ti-6Al-4V components for load-bearing applications. A batch of 64 Ti-6Al-4V sheet samples with dimensions of 210/180 mm × 42 mm × 3 mm have been additively manufactured by selective electron beam melting (SEBM). A comprehensive assessment was then made of their density, surface flatness, microstructure, and mechanical properties in both as-built and hot isostatically pressed conditions, including the influence of the hot isostatic pressing (HIP) temperature. In particular, standard long tensile (156 mm long, 2 mm thick) and fatigue (206 mm long, 2 mm thick) test sheet samples were used for assessment. As-built SEBM Ti-6Al-4V sheet samples with machined surfaces fully satisfied the minimum tensile property requirements for mill-annealed TIMETAL Ti-6Al-4V sheet products, whereas HIP-processed samples (2 mm thick) with machined surfaces achieved a high cycle fatigue (HCF) strength of 625 MPa (R = 0.06, 107 cycles), similar to mill-annealed Ti-6Al-4V (500-700 MPa). The unflatness was limited to 0.2 mm in both the as-built and HIP-processed conditions. A range of other revealing observations was discussed for the additive manufacturing of the Ti-6Al-4V sheet structures.

Dissociation of β-Sheet Stacking of Amyloid β Fibrils by Irradiation of Intense, Short-Pulsed Mid-infrared Laser.

PubMed

Kawasaki, Takayasu; Yaji, Toyonari; Ohta, Toshiaki; Tsukiyama, Koichi; Nakamura, Kazuhiro

2018-02-05

Structure of amyloid β (Aβ) fibrils is rigidly stacked by β-sheet conformation, and the fibril state of Aβ is profoundly related to pathogenesis of Alzheimer's disease (AD). Although mid-infrared light has been used for various biological researches, it has not yet been known whether the infrared light changes the fibril structure of Aβ. In this study, we tested the effect of irradiation of intense mid-infrared light from a free-electron laser (FEL) targeting the amide bond on the reduction of β-sheet content in Aβ fibrils. The FEL reduced entire contents of proteins exhibiting β-sheet structure in brain sections from AD model mice, as shown by synchrotron-radiation infrared microscopy analysis. Since Aβ 1-42 fibril absorbed a considerable FEL energy at amide I band (6.17 μm), we irradiated the FEL at 6.17 μm and found that β-sheet content of naked Aβ 1-42 fibril was decreased using infrared microscopic analysis. Consistent with the decrease in the β-sheet content, Congo-red signal is decreased after the irradiation to Aβ 1-42 fibril. Furthermore, electron microscopy analysis revealed that morphologies of the fibril and proto-fibril were largely changed after the irradiation. Thus, mid-infrared light dissociates β-sheet structure of Aβ fibrils, which justifies exploration of possible laser-based therapy for AD.

A preliminary exploration of the feasibility of offering men information about potential prostate cancer treatment options before they know their biopsy results.

PubMed

Zeliadt, Steven B; Hannon, Peggy A; Trivedi, Ranak B; Bonner, Laura M; Vu, Thuy T; Simons, Carol; Kimmie, Crystal A; Hu, Elaine Y; Zipperer, Chris; Lin, Daniel W

2013-02-06

A small pre-test study was conducted to ascertain potential harm and anxiety associated with distributing information about possible cancer treatment options at the time of biopsy, prior to knowledge about a definitive cancer diagnosis. Priming men about the availability of multiple options before they have a confirmed diagnosis may be an opportunity to engage patients in more informed decision-making. Men with an elevated PSA test or suspicious Digital Rectal Examination (DRE) who were referred to a urology clinic for a biopsy were randomized to receive either the clinic's usual care (UC) biopsy instruction sheet (n = 11) or a pre-biopsy educational (ED) packet containing the biopsy instruction sheet along with a booklet about the biopsy procedure and a prostate cancer treatment decision aid originally written for newly diagnosed men that described in detail possible treatment options (n = 18). A total of 62% of men who were approached agreed to be randomized, and 83% of the ED group confirmed they used the materials. Anxiety scores were similar for both groups while awaiting the biopsy procedure, with anxiety scores trending lower in the ED group: 41.2 on a prostate-specific anxiety instrument compared to 51.7 in the UC group (p = 0.13). ED participants reported better overall quality of life while awaiting biopsy compared to the UC group (76.4 vs. 48.5, p = 0.01). The small number of men in the ED group who went on to be diagnosed with cancer reported being better informed about the risks and side effects of each option compared to men diagnosed with cancer in the UC group (p = 0.07). In qualitative discussions, men generally reported they found the pre-biopsy materials to be helpful and indicated having information about possible treatment options reduced their anxiety. However, 2 of 18 men reported they did not want to think about treatment options until after they knew their biopsy results. In this small sample offering pre-biopsy education about potential treatment options was generally well received by patients, appeared to be beneficial to men who went on to be diagnosed, and did not appear to increase anxiety unnecessarily among those who had a negative biopsy.

[Orality and writing: argumentation in children with attention deficit hyperactivity disorder].

PubMed

Gallardo-Paúls, Beatriz; Moreno-Campos, Verónica

2014-02-24

This work takes a deeper look at the differences in the linguistic competence of children with attention deficit hyperactivity disorder (ADHD) in terms of both orality and writing. The purpose of this study is to check whether, in oral tasks, these children present the same problems related to inhibition and self-regulation as those pointed out in research working with written data. Likewise it seeks to describe those problems (lack of appropriateness, inappropriate production) as they appear in our oral data. A written and an oral argumentation produced by 25 participants between 9 and 11 years of age were analysed. In the written task, the children wrote their argumentations, and in the oral task their argumentative interaction with a collaborator was videotaped and later the types of arguments used in each case (logical, fallacies, sanctioning or moralist) were analysed. There is an obvious difference between the results in the two tests, which suggests the need to review the verbal evaluation mechanisms and to complete the written results with oral skill tests. The problems normally associated with written tasks do not appear in oral language; participants are able to follow the discursive thread and to provide new arguments related with the topic. The data obtained highlight the added difficulty of a written task for children with ADHD, the reliability of the oral results with regard to linguistic skills, and the need to use both types of data in evaluations.

Marine evidence of a deconvolving Antarctic Ice Sheet during post-LGM retreat of the Ross Sea sector

NASA Astrophysics Data System (ADS)

Prothro, L. O.; Yokoyama, Y.; Simkins, L. M.; Anderson, J. B.; Majewski, W.; Yamane, M.; Ohkouchi, N.

2017-12-01

Predictive models of ice sheet and sea level change are dependent on observational data of ice-sheet behavior for model testing and tuning. The geologic record contains a wealth of information about ice-sheet dynamics, with fewer logistical, spatial, and temporal limitations than are involved in data acquisition along contemporary ice margins. However, past ice-sheet behavior is still largely uncertain or contested due to issues with obtaining meaningful radiocarbon dates. We minimize bias from glacially-reworked carbon and limitations from unknown geomorphic context and uncertainty in sediment facies identification by using careful sedimentary analyses within a geomorphic framework, as well as selection of appropriate dating methods. Our study area, the Ross Sea sector of Antarctica, is the primary drainage outlet for 25% of the continent's grounded ice. During the Last Glacial Maximum, the low-profile, marine-based West Antarctic Ice Sheet (WAIS) and the steeper profile, largely land-based East Antarctic Ice Sheet (EAIS) converged in the Ross Sea to flow out to or near the continental shelf edge. Geomorphic and sedimentary data reveal that during their subsequent retreat to form the Ross Sea Embayment, the two ice sheets behaved differently, with the WAIS rapidly retreating tens of kilometers followed by extended pauses, while the EAIS retreated steadily, with shorter (decadal- to century-long) pauses. This behavior leads us to believe that the two ice sheets may have contributed diachronously to sea level. By acquiring accurate timing of grounding line retreat, we are able to calculate volumes of ice lost throughout deglaciation, as well as associated sea level contributions. In addition, we attempt to rectify the contradicting marine and terrestrial interpretations of retreat patterns from the Ross Sea continental shelf.

Holocene temperature history at the west Greenland Ice Sheet margin reconstructed from lake sediments

NASA Astrophysics Data System (ADS)

Axford, Y.; Losee, S.; Briner, J. P.; Francis, D.; Langdon, P. G.; Walker, I.

2011-12-01

Paleoclimate proxy data can help reduce uncertainties regarding how the Greenland Ice Sheet, and thus global sea level, will respond to future climate change. Studies of terrestrial deposits along Greenland's margins offer opportunities to reconstruct both past temperature changes and the associated changes in Greenland Ice Sheet extent, thus empirically characterizing the ice sheet's response to temperature change. Here we present Holocene paleoclimate reconstructions developed from sediment records of five lakes along the western ice sheet margin, near Jakobshavn Isbræ and Disko Bugt. Insect (Chironomidae, or non-biting midge) remains from North Lake provide quantitative estimates of summer temperatures over the past ca. 7500 years at multi-centennial resolution, and changes in sediment composition at all five lakes offer evidence for glacier fluctuations, changes in lake productivity, and other environmental changes throughout the Holocene. Aims of this study include quantification of warmth in the early to mid Holocene, when summer solar insolation forcing exceeded present-day values at northern latitudes and the local Greenland Ice Sheet margin receded inboard of its present position, and the magnitude of subsequent Neoglacial and Little Ice Age cooling that drove ice sheet expansion. We find that the Jakobshavn Isbrae region experienced the warmest temperatures of the Holocene (with summers 2 to 3.5 degrees C warmer than present) between ~6000 and 4000 years ago. Neoglacial cooling began rather abruptly ~4000 years ago and intensified 3000 years ago. Our proxy data suggest that the coldest summers of the Holocene occurred during the 18th and 19th centuries in the Jakobshavn region. These results agree well with previous glacial geologic studies reconstructing local ice margin positions through the Holocene. Such reconstructions of paleoclimate and past ice sheet extent provide targets for testing and improving ice sheet models.

Teaching clinical management skills for genetic testing of hereditary nonpolyposis colorectal cancer using a Web-based tutorial.

PubMed

Barnes, Kathleen; Itzkowitz, Steven; Brown, Karen

2003-01-01

To pilot and evaluate an interactive Web-based continuing medical education tutorial on clinical management of hereditary nonpolyposis colon cancer (HNPCC) and genetic testing. Gastroenterology fellows and genetic counseling trainees were asked to read standard written materials before taking the tutorial. A pretest/post-test assessment was used to measure change in subjects' clinical management skills. Subjects made the correct management decision 63.9% of the time before the tutorial and 81.1% of the time after the tutorial (P < 0.001). Supplementing written materials with an interactive program may assist medical professionals in integrating their knowledge of HNPCC and genetic testing into clinical practice.

Energized Oxygen : Speiser Current Sheet Bifurcation

NASA Astrophysics Data System (ADS)

George, D. E.; Jahn, J. M.

2017-12-01

A single population of energized Oxygen (O+) is shown to produce a cross-tail bifurcated current sheet in 2.5D PIC simulations of the magnetotail without the influence of magnetic reconnection. Treatment of oxygen in simulations of space plasmas, specifically a magnetotail current sheet, has been limited to thermal energies despite observations of and mechanisms which explain energized ions. We performed simulations of a homogeneous oxygen background, that has been energized in a physically appropriate manner, to study the behavior of current sheets and magnetic reconnection, specifically their bifurcation. This work uses a 2.5D explicit Particle-In-a-Cell (PIC) code to investigate the dynamics of energized heavy ions as they stream Dawn-to-Dusk in the magnetotail current sheet. We present a simulation study dealing with the response of a current sheet system to energized oxygen ions. We establish a, well known and studied, 2-species GEM Challenge Harris current sheet as a starting point. This system is known to eventually evolve and produce magnetic reconnection upon thinning of the current sheet. We added a uniform distribution of thermal O+ to the background. This 3-species system is also known to eventually evolve and produce magnetic reconnection. We add one additional variable to the system by providing an initial duskward velocity to energize the O+. We also traced individual particle motion within the PIC simulation. Three main results are shown. First, energized dawn- dusk streaming ions are clearly seen to exhibit sustained Speiser motion. Second, a single population of heavy ions clearly produces a stable bifurcated current sheet. Third, magnetic reconnection is not required to produce the bifurcated current sheet. Finally a bifurcated current sheet is compatible with the Harris current sheet model. This work is the first step in a series of investigations aimed at studying the effects of energized heavy ions on magnetic reconnection. This work differs significantly from previous investigations involving heavy ions in that they are energized as opposed to being simply thermal. This is a variation based firmly on published in-situ measurements. It also differs in that a complete population is used as opposed to simply test particles in a magnetic field model.

An Experimental Study of Fatigue Crack Growth in Aluminum Sheet Subjected to Combined Bending and Membrane Stresses

NASA Technical Reports Server (NTRS)

Phillips, Edward P.

1997-01-01

An experimental study was conducted to determine the effects of combined bending and membrane cyclic stresses on the fatigue crack growth behavior of aluminum sheet material. The materials used in the tests were 0.040-in.- thick 2024-T3 alclad and 0.090-in.-thick 2024-T3 bare sheet. In the tests, the membrane stresses were applied as a constant amplitude loading at a stress ratio (minimum to maximum stress) of 0.02, and the bending stresses were applied as a constant amplitude deflection in phase with the membrane stresses. Tests were conducted at ratios of bending to membrane stresses (B/M) of 0, 0.75, and 1.50. The general trends of the results were for larger effects of bending for the higher B/M ratios, the lower membrane stresses, and the thicker material. The addition of cyclic bending stresses to a test with cyclic membrane stresses had only a small effect on the growth rates of through-thickness cracks in the thin material, but had a significant effect on the crack growth rates of through-thickness cracks in the thick material. Adding bending stresses to a test had the most effect on the initiation and early growth of cracks and had less effect on the growth of long through-thickness cracks.

A Unified Constitutive Model for Subglacial Till, Part II: Laboratory Tests, Disturbed State Modeling, and Validation for Two Subglacial Tills

NASA Astrophysics Data System (ADS)

Desai, C. S.; Sane, S. M.; Jenson, J. W.; Contractor, D. N.; Carlson, A. E.; Clark, P. U.

2006-12-01

This presentation, which is complementary to Part I (Jenson et al.), describes the application of the Disturbed State Concept (DSC) constitutive model to define the behavior of the deforming sediment (till) underlying glaciers and ice sheets. The DSC includes elastic, plastic, and creep strains, and microstructural changes leading to degradation, failure, and sometimes strengthening or healing. Here, we describe comprehensive laboratory experiments conducted on samples of two regionally significant tills deposited by the Laurentide Ice Sheet: the Tiskilwa Till and Sky Pilot Till. The tests are used to determine the parameters to calibrate the DSC model, which is validated with respect to the laboratory tests by comparing the predictions with test data used to find the parameters, and also comparing them with independent tests not used to find the parameters. Discussion of the results also includes comparison of the DSC model with the classical Mohr-Coulomb model, which has been commonly used for glacial tills. A numerical procedure based on finite element implementation of the DSC is used to simulate an idealized field problem, and its predictions are discussed. Based on these analyses, the unified DSC model is proposed to provide an improved model for subglacial tills compared to other models used commonly, and thus to provide the potential for improved predictions of ice sheet movements.

Ultrasonic Fatigue Endurance of Thin Carbon Fiber Sheets

NASA Astrophysics Data System (ADS)

Domínguez Almaraz, Gonzalo M.; Ruiz Vilchez, Julio A.; Dominguez, Aymeric; Meyer, Yann

2016-04-01

Ultrasonic fatigue tests were carried out on thin carbon fiber sheets (0.3 mm of thickness) to determine the fatigue endurance under very high-frequency loading (20 kHz). This material, called the gas diffusion layer (GDL), plays a major role in the overall performances of proton exchange membrane fuel cells (PEMFCs). The study of its physical-chemical properties is an on-going subject in the literature; nevertheless, no knowledge is available concerning the high-frequency fatigue endurance. A principal difficulty in carrying out ultrasonic fatigue tests on this material was to determine the dimensions of testing specimen to fit the resonance condition. This aspect was solved by modal numerical simulation: The testing specimen has been a combination of a low-strength steel frame (to facilitate the attachment to the ultrasonic machine and to increase the mass of the specimen), and the carbon fiber hourglass-shape profile. Under resonance condition, a stationary elastic wave is generated along the specimen that induces high stress at the neck section and high displacements at the ends. Results show that fatigue life was close to 3 × 108 cycles when the high Von Misses stress at the neck section was 170 MPa, whereas fatigue life attains the 4.5 × 109 cycles when stress decreases to 117 MPa. Crack initiation and propagation were analyzed, and conclusions were drawn concerning the fatigue endurance of these fiber carbon sheets under ultrasonic fatigue testing.

Characterization of zinc alloy by sheet bulging test with analytical models and digital image correlation

NASA Astrophysics Data System (ADS)

Vitu, L.; Laforge, N.; Malécot, P.; Boudeau, N.; Manov, S.; Milesi, M.

2018-05-01

Zinc alloys are used in a wide range of application such as electronics, automotive and building construction. Their various shapes are generally obtained by metal forming operation such as stamping. Therefore, it is important to characterize the material with adequate characterization tests. Sheet Bulging Test (SBT) is well recognized in the metal forming community. Different theoretical models of the literature for the evaluation of thickness and radius of the deformed sheet in SBT have been studied in order to get the hardening curve of different materials. These theoretical models present the advantage that the experimental procedure is very simple. But Koç et al. showed their limitation, since the combination of thickness and radius evaluations depend on the material. As Zinc alloys are strongly anisotropic with a special crystalline structure, a procedure is adopted for characterizing the hardening curve of a Zinc alloy. The anisotropy is first studied with tensile test, and SBT with elliptical dies is also investigated. Parallel to this, Digital Image Correlation (DIC) measures are carried out. The results obtained from theoretical models and DIC measures are compared. Measures done on post-mortem specimens complete the comparisons. Finally, DIC measures give better results and the resulting hardening curve of the studied zinc alloy is provided.

Comparing written and oral measures of comprehension of cancer information by English-as-a-Second-Language Chinese immigrant women.

PubMed

McWhirter, Jennifer; Todd, Laura; Hoffman-Goetz, Laurie

2011-09-01

The Short Test of Functional Health Literacy for Adults (S-TOFHLA) and Cloze test are commonly used tools to measure comprehension of health information (i.e., health literacy); however, little is known about their use in English-as-a-Second-Language (ESL) populations. In this study, we compared written (Cloze test) and oral (Teach Back) measures of colon cancer information comprehension among ESL Chinese immigrant women to Canada. Performances on colon cancer-specific measures were compared to a general measure of health literacy (S-TOFHLA). On the S-TOFHLA, Cloze, and Teach Back, respectively, the following percentage of participants had adequate comprehension: 62.1%, 14.8%, and 89.7%. Correlation between performance on the Cloze and Teach Back was significant albeit weakly so (r = 0.38, p = 0.04); performances on the S-TOFHLA and Teach Back were not correlated. Measures of health literacy skill that require written English language skills may not be appropriate for measuring understanding of health information for ESL populations.

Detection of Genital HPV Infection Using Urine Samples: a Population Based Study in India.

PubMed

Sabeena, Sasidharanpillai; Bhat, Parvati; Kamath, Veena; Mathew, Mary; Aswathyraj, Sushama; Devadiga, Santhosha; Prabhu, Suresha; Hindol, Maity; Chameetachal, Akhil; Krishnan, Anjana; Arunkumar, Govindakarnavar

2016-01-01

Cervical cancer is the second commonest cancer among Indian women and its association with human papilloma virus (HPV) is well established. This preventable cancer accounts for the maximum number of cancer related deaths among rural Indian women. Unlike in developed countries there are no organized cervical cancer screening programmes in India due to lack of resources and manpower. To detect genital HPV infection using urine samples among asymptomatic rural women in the age group of 18-65 years. The study area chosen was Perdoor village in Udupi Taluk, Karnataka State and all the women in the age group of 18-65 years formed the study cohort. A cross sectional study was conducted by house visits and 1,305 women were enrolled in the study. After taking written informed consent a data sheet was filled and early stream random urine samples were collected, transported to a laboratory at 4OC and aliquoted. Samples were tested using nested HPV PCR with PGMY09/11 and GP5+/6+ primers. Positive cases were genotyped by sequence analysis. Study participants included 1,134 sexually active and 171 unmarried women with a mean age at marriage of 22.1 (SD=3.9) years. Study area showed high female literacy rate of 86.6%. Five urine samples tested positive for HPV DNA (0.4%). We found very low genital HPV infection rate among women from monogamous community. This is the first major population based study carried out among asymptomatic rural women to detect genital HPV infectio from Karnataka using urine samples.

A Historical Forcing Ice Sheet Model Validation Framework for Greenland

NASA Astrophysics Data System (ADS)

Price, S. F.; Hoffman, M. J.; Howat, I. M.; Bonin, J. A.; Chambers, D. P.; Kalashnikova, I.; Neumann, T.; Nowicki, S.; Perego, M.; Salinger, A.

2014-12-01

We propose an ice sheet model testing and validation framework for Greenland for the years 2000 to the present. Following Perego et al. (2014), we start with a realistic ice sheet initial condition that is in quasi-equilibrium with climate forcing from the late 1990's. This initial condition is integrated forward in time while simultaneously applying (1) surface mass balance forcing (van Angelen et al., 2013) and (2) outlet glacier flux anomalies, defined using a new dataset of Greenland outlet glacier flux for the past decade (Enderlin et al., 2014). Modeled rates of mass and elevation change are compared directly to remote sensing observations obtained from GRACE and ICESat. Here, we present a detailed description of the proposed validation framework including the ice sheet model and model forcing approach, the model-to-observation comparison process, and initial results comparing model output and observations for the time period 2000-2013.

A Ffowcs Williams and Hawkings formulation for hydroacoustic analysis of propeller sheet cavitation

NASA Astrophysics Data System (ADS)

Testa, C.; Ianniello, S.; Salvatore, F.

2018-01-01

A novel hydroacoustic formulation for the prediction of tonal noise emitted by marine propellers in presence of unsteady sheet cavitation, is presented. The approach is based on the standard Ffowcs Williams and Hawkings equation and the use of transpiration (velocity and acceleration) terms, accounting for the time evolution of the vapour cavity attached on the blade surface. Drawbacks and potentialities of the method are tested on a marine propeller operating in a nonhomogeneous onset flow, by exploiting the hydrodynamic data from a potential-based panel method equipped with a sheet cavitation model and comparing the noise predictions with those carried out by an alternative numerical approach, documented in literature. It is shown that the proposed formulation yields a one-to-one correlation between emitted noise and sheet cavitation dynamics, carrying out accurate predictions in terms of noise magnitude and directivity.

DNA book.

PubMed

Kawai, Jun; Hayashizaki, Yoshihide

2003-06-01

We propose herein a new method of DNA distribution, whereby DNA clones or PCR products are printed directly onto the pages of books and delivered to users along with relevant scientific information. DNA sheets, comprising water-soluble paper onto which DNA is spotted, can be bound into books. Readers can easily extract the DNA fragments from DNA sheets and amplify them using PCR. We show that DNA sheets can withstand various conditions that may be experienced during bookbinding and delivery, such as high temperatures and humidity. Almost all genes (95%-100% of randomly selected RIKEN mouse cDNA clones) were recovered successfully by use of PCR. Readers can start their experiments after a 2-h PCR amplification without waiting for the delivery of DNA clones. The DNA Book thus provides a novel method for delivering DNA in a timely and cost-effective manner. A sample DNA sheet (carrying RIKEN mouse cDNA clones encoding genes of enzymes for the TCA cycle) is included in this issue for field-testing. We would greatly appreciate it if readers could attempt to extract DNA and report the results and whether the DNA sheet was shipped to readers in good condition.

Carbon Nanotube Thin-Film Antennas.

PubMed

Puchades, Ivan; Rossi, Jamie E; Cress, Cory D; Naglich, Eric; Landi, Brian J

2016-08-17

Multiwalled carbon nanotube (MWCNT) and single-walled carbon nanotube (SWCNT) dipole antennas have been successfully designed, fabricated, and tested. Antennas of varying lengths were fabricated using flexible bulk MWCNT sheet material and evaluated to confirm the validity of a full-wave antenna design equation. The ∼20× improvement in electrical conductivity provided by chemically doped SWCNT thin films over MWCNT sheets presents an opportunity for the fabrication of thin-film antennas, leading to potentially simplified system integration and optical transparency. The resonance characteristics of a fabricated chlorosulfonic acid-doped SWCNT thin-film antenna demonstrate the feasibility of the technology and indicate that when the sheet resistance of the thin film is >40 ohm/sq no power is absorbed by the antenna and that a sheet resistance of <10 ohm/sq is needed to achieve a 10 dB return loss in the unbalanced antenna. The dependence of the return loss performance on the SWCNT sheet resistance is consistent with unbalanced metal, metal oxide, and other CNT-based thin-film antennas, and it provides a framework for which other thin-film antennas can be designed.

Rapid model building of beta-sheets in electron-density maps.

PubMed

Terwilliger, Thomas C

2010-03-01

A method for rapidly building beta-sheets into electron-density maps is presented. beta-Strands are identified as tubes of high density adjacent to and nearly parallel to other tubes of density. The alignment and direction of each strand are identified from the pattern of high density corresponding to carbonyl and C(beta) atoms along the strand averaged over all repeats present in the strand. The beta-strands obtained are then assembled into a single atomic model of the beta-sheet regions. The method was tested on a set of 42 experimental electron-density maps at resolutions ranging from 1.5 to 3.8 A. The beta-sheet regions were nearly completely built in all but two cases, the exceptions being one structure at 2.5 A resolution in which a third of the residues in beta-sheets were built and a structure at 3.8 A in which under 10% were built. The overall average r.m.s.d. of main-chain atoms in the residues built using this method compared with refined models of the structures was 1.5 A.

Tensile and pack compressive tests of some sheets of aluminum alloy, 1025 carbon steel, and chromium-nickel steel

NASA Technical Reports Server (NTRS)

Atchison, C S; Miller, James A

1942-01-01

Tensile and compressive stress-strain curves, stress-deviation curves, and secant modulus-stress curves are given for longitudinal and transverse specimens of 17S-T, 24S-T, and 24S-RT aluminum-alloy sheet in thicknesses from 0.032 to 0.081 inch, 1025 carbon steel sheet in thicknesses of 0.054 and 0.120 inch, and chromium-nickel steel sheet in thicknesses form 0.020 to 0.0275 inch. Significant differences were found between the tensile and the compressive stress-strain curves, and also the corresponding corollary curves; similarly, differences were found between the curves for the longitudinal and transverse directions. These differences are of particular importance in considering the compressive strength of aircraft structures made of thin sheet. They are explored further for the case of compression by giving tangent modulus-stress curves in longitudinal and transverse compression and dimensionless curves of the ratio of tangent modulus to Young's modulus and of the ratio of reduced modulus for a rectangular section to Young's modulus, both plotted against the ratio of stress to secant yield strength.

Energization of the Ring Current through Convection of Substorm Enhancements of the Plasma Sheet Source.

NASA Astrophysics Data System (ADS)

Menz, A.; Kistler, L. M.; Mouikis, C.; Spence, H. E.; Henderson, M. G.; Matsui, H.

2017-12-01

It has been shown that electric field strength and night-side plasma sheet density are the two best predictors of the adiabatic energy gain of the ring current during geomagnetic storms (Liemohn and Khazanov, 2005). While H+ dominates the ring current during quiet times, O+ can contribute substantially during geomagnetic storms. Substorm activity provides a mechanism to enhance the energy density of O+ in the plasma sheet during geomagnetic storms, which is then convected adiabatically into the inner-magnetosphere. Using the Van Allen Probes data in the the plasma sheet source region (defined as L>5.5 during storms) and the inner magnetosphere, along with LANL-GEO data to identify substorm injection times, we show that adiabatic convection of O+ enhancements in the source region can explain the observed enhancements in the inner magnetosphere. We use the UNH-IMEF electric field model to calculate drift times from the source region to the inner magnetosphere to test whether enhancements in the inner-magnetosphere can be explained by dipolarization driven enhancements in the plasma sheet source hours before.

Facilities | Geothermal Technologies | NREL

Science.gov Websites

research, development, analysis, and deployment. A photo of the Thermal Test Facility at NREL. Thermal Test development of building and thermal energy systems. For more information, read the fact sheet

Context in Text: The Development of Oral and Written Language in Two Genres.

ERIC Educational Resources Information Center

Pellegrini, A. D.; And Others

1984-01-01

Tests Halliday's model of context/text relationships and how these relationships vary for 71 children in first, second, and third grades. Children produced oral and written messages about a circus in narrative and persuasive genres. Texts were analyzed for elements of linguistic cohesion and length of clausal themes. (Author/CB)

Evidence in Support of Written Corrective Feedback

ERIC Educational Resources Information Center

Bitchener, John

2008-01-01

The extent to which ESL learners benefit from written corrective feedback has been debated at length since Truscott (1996) mounted a case for its abolition. Ten years later, the debate continues, not only because little attention has been given to testing its efficacy over time but also because studies that have investigated the issue have not…

78 FR 2340 - Energy Conservation Program: Test Procedures for Residential Water Heaters and Commercial Water...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-01-11

... Manufacturing Technical Corrections Act (AEMTCA; H.R. 6582), which was signed into law on December 18, 2012 (Pub... address those statutory requirements. DOE welcomes written comments from the public on any subject within...: Written comments and information are requested on or before February 11, 2013. ADDRESSES: Interested...

The Psychometric Properties of the Agricultural Hazardous Occupations Order Certification Training Program Written Examinations

ERIC Educational Resources Information Center

French, Brian F.; Breidenbach, Daniel H.; Field, William E.; Tormoehlen, Roger

2007-01-01

The written certification exam that accompanies the Gearing Up for Safety-Agricultural Production Safety Training for Youth curriculum was designed to partially meet the testing requirements of the Agricultural Hazardous Occupations Order (AgHOs) Certification Training Program. This curriculum and accompanying assessment tools are available for…

Communicating Cardiovascular Disease Risk Due to Elevated Homocysteine Levels: Using the EPPM to Develop Print Materials

ERIC Educational Resources Information Center

McKay, Diane L.; Berkowitz, Judy M.; Blumberg, Jeffrey B.; Goldberg, Jeanne P.

2004-01-01

Improving the effectiveness of written information to promote compliance with therapeutic regimens is essential, particularly among older adults. Guiding their development and evaluating their effectiveness with an accepted communication theory or model may help. A preliminary test of written materials developed within the context of the Extended…

34 CFR 98.9 - Investigation and findings.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 34 Education 1 2010-07-01 2010-07-01 false Investigation and findings. 98.9 Section 98.9 Education... TESTING § 98.9 Investigation and findings. (a) The Office may permit the parties to submit further written... complainant and recipient or contractor written notice of its findings and the basis for its findings. (c) If...

A Creativity Index for Studying the Free Written Production of Bilinguals.

ERIC Educational Resources Information Center

Lauren, Ulla

1991-01-01

To test whether additive bilinguals are more linguistically creative than monolinguals, a creativity index, based upon linguistic features thought to correspond to the distinctive features of creativity, was calculated from essays written by pupils in a Finnish-Swedish comprehensive school. The results did not seem to reveal higher creativity…

A Comparative Content Analysis of Vegetarian Food Blogs Written by Registered Dietitians and Non-Registered Dietitians.

PubMed

Dumas, Audrée-Anne; Lemieux, Simone; Lapointe, Annie; Dugrenier, Marilyn; Desroches, Sophie

2017-06-01

This purpose of this study was to compare the nutritional content of vegetarian recipes published in food blogs written by registered dietitians (RDs) and by non-registered dietitians (non-RDs). Twelve food blogs written by RDs and 12 written by non-RDs were selected using a systematic approach. For each food blog, 2 vegetarian entrée recipes per season were selected (n = 192 recipes). Descriptive analyses were performed using Fisher's exact test. Median nutritional values per serving between RDs' and non-RDs' recipes were compared using Wilcoxon-Mann-Whitney tests. RDs' recipes were significantly lower in energy, non-heme iron, vitamin C, and sodium, contained significantly more vitamin D and had a higher protein proportion than non-RDs' recipes. Disparities were also observed across type of entrée and vegetarian dietary pattern. In conclusion, this study showed that RD and non-RD food bloggers provided vegetarian recipes with few nutritional differences. Whether expanding the comparative analysis between RDs and non-RDs' blogs targeting different nutrition-related topics would yield different results remains to be investigated.

Some investigations of the general instability of stiffened metal cylinders III : continuation of tests of wire-braced specimens and preliminary tests of sheet-covered specimens

NASA Technical Reports Server (NTRS)

1943-01-01

This is the third of a series of reports covering an investigation of the general instability problem by the California Institute of Technology. The first five reports of this series cover investigations of the general instability problem under the loading conditions of pure bending and were prepared under the sponsorship of the Civil Aeronautics Administration. The succeeding reports of this series cover the work done on other loading conditions under the sponsorship of the National Advisory Committee for Aeronautics. This report is concerned primarily with the continuation of the tests of wire-braced specimens, and preliminary tests of sheet-covered specimens that had been made in the experimental investigation on the problem of the general instability of stiffened metal cylinders at the C.I.T.

ICAM (Integrated Computer Aided Manufacturing) Conceptual Design for Computer-Integrated Manufacturing. Volume 1. Project Overview and Technical Summary

DTIC Science & Technology

1984-06-29

sheet metal, machined and composite parts and assembling the components into final pruJucts o Planning, evaluating, testing, inspecting and...Research showed that current programs were pursuing the design and demonstration of integrated centers for sheet metal, machining and composite ...determine any metal parts required and to schedule these requirements from the machining center. Figure 3-33, Planned Composite Production, shows

Multifunctional Hybrid Carbon Nanotube/Carbon Fiber Polymer Composites

NASA Technical Reports Server (NTRS)

Kang, Jin Ho; Cano, Roberto J.; Ratcliffe, James G.; Luong, Hoa; Grimsley, Brian W.; Siochi, Emilie J.

2016-01-01

For aircraft primary structures, carbon fiber reinforced polymer (CFRP) composites possess many advantages over conventional aluminum alloys due to their light weight, higher strengthand stiffness-to-weight ratio, and low life-cycle maintenance costs. However, the relatively low electrical and thermal conductivities of CFRP composites fail to provide structural safety in certain operational conditions such as lightning strikes. Despite several attempts to solve these issues with the addition of carbon nanotubes (CNT) into polymer matrices, and/or by interleaving CNT sheets between conventional carbon fiber (CF) composite layers, there are still interfacial problems that exist between CNTs (or CF) and the resin. In this study, hybrid CNT/CF polymer composites were fabricated by interleaving layers of CNT sheets with Hexcel® IM7/8852 prepreg. Resin concentrations from 1 wt% to 50 wt% were used to infuse the CNT sheets prior to composite fabrication. The interlaminar properties of the resulting hybrid composites were characterized by mode I and II fracture toughness testing (double cantilever beam and end-notched flexure test). Fractographical analysis was performed to study the effect of resin concentration. In addition, multi-directional physical properties like thermal conductivity of the orthotropic hybrid polymer composite were evaluated. Interleaving CNT sheets significantly improved the in-plane (axial and perpendicular direction of CF alignment) thermal conductivity of the hybrid composite laminates by 50 - 400%.

40 CFR 60.534 - Test methods and procedures.

Code of Federal Regulations, 2010 CFR

2010-07-01

... testing. However, manufacturers shall not involve themselves in the conduct of the test after the pretest... prior to the first pretest burn of the certification series. Written communications between the...

40 CFR 60.534 - Test methods and procedures.

Code of Federal Regulations, 2014 CFR

2014-07-01

... testing. However, manufacturers shall not involve themselves in the conduct of the test after the pretest... prior to the first pretest burn of the certification series. Written communications between the...

40 CFR 60.534 - Test methods and procedures.

Code of Federal Regulations, 2012 CFR

2012-07-01

... testing. However, manufacturers shall not involve themselves in the conduct of the test after the pretest... prior to the first pretest burn of the certification series. Written communications between the...

40 CFR 60.534 - Test methods and procedures.

Code of Federal Regulations, 2011 CFR

2011-07-01

... testing. However, manufacturers shall not involve themselves in the conduct of the test after the pretest... prior to the first pretest burn of the certification series. Written communications between the...

40 CFR 60.534 - Test methods and procedures.

Code of Federal Regulations, 2013 CFR

2013-07-01

... testing. However, manufacturers shall not involve themselves in the conduct of the test after the pretest... prior to the first pretest burn of the certification series. Written communications between the...

Nd:YAG laser welding of coated sheet steel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Graham, M.P.; Kerr, H.W.; Weckman, D.C.

1994-12-31

Coated sheet steels are used extensively in the automotive industry for the fabrication of automobile body components; however, their reduced weldability by the traditional welding processes has led to numerous studies into the use of alternate process such as laser welding. In this paper, we present a modified joint geometry which allows high quality lap welds of coated sheet steels to be made by laser welding processes. Hot-dipped galvanized sheet (16 gauge), with a 60 g/m zinc coating was used in this study. A groove was created in the top sheet of a specimen pair by pressing piano wires ofmore » various diameters into the sheet. The specimens were clamped together in a lag-joint configuration such that they were in contacted only along the grove projection. A parametric study was conducted using the variables of welding speed, laser mean power (685 W, 1000 W and 1350 W), and grove size. Weld quality and weld pool dimensions were assessed using metallurgical cross-sections and image analysis techniques. Acceptable quality seam welds were produced in the galvanized sheet steel with both grove sizes when using 1000 W and 1350 W laser mean powers and a range of welding speeds. Results of the shear-tensile tests showed that high loads to failure, with failure occurring in the parent material, were predominately found in welds produced at speeds over 1.2 m/min and when using the high mean laser powers: 1000 W and 1350 W. A modified lap joint geometry, in which a groove is pre-placed in the top sheet of the lap-joint configuration, has been developed which permits laser welding of coated sheet steels. Good quality seam welds have been produced in 16 gauge galvanized sheet steels at speeds up to 2.7 m/min using a 2 kW CW Nd:YAG laser operating at 1350 W laser mean power. Weld quality was not affected by changes in groove size.« less

Insolation-driven 100,000-year glacial cycles and hysteresis of ice-sheet volume.

PubMed

Abe-Ouchi, Ayako; Saito, Fuyuki; Kawamura, Kenji; Raymo, Maureen E; Okuno, Jun'ichi; Takahashi, Kunio; Blatter, Heinz

2013-08-08

The growth and reduction of Northern Hemisphere ice sheets over the past million years is dominated by an approximately 100,000-year periodicity and a sawtooth pattern (gradual growth and fast termination). Milankovitch theory proposes that summer insolation at high northern latitudes drives the glacial cycles, and statistical tests have demonstrated that the glacial cycles are indeed linked to eccentricity, obliquity and precession cycles. Yet insolation alone cannot explain the strong 100,000-year cycle, suggesting that internal climatic feedbacks may also be at work. Earlier conceptual models, for example, showed that glacial terminations are associated with the build-up of Northern Hemisphere 'excess ice', but the physical mechanisms underpinning the 100,000-year cycle remain unclear. Here we show, using comprehensive climate and ice-sheet models, that insolation and internal feedbacks between the climate, the ice sheets and the lithosphere-asthenosphere system explain the 100,000-year periodicity. The responses of equilibrium states of ice sheets to summer insolation show hysteresis, with the shape and position of the hysteresis loop playing a key part in determining the periodicities of glacial cycles. The hysteresis loop of the North American ice sheet is such that after inception of the ice sheet, its mass balance remains mostly positive through several precession cycles, whose amplitudes decrease towards an eccentricity minimum. The larger the ice sheet grows and extends towards lower latitudes, the smaller is the insolation required to make the mass balance negative. Therefore, once a large ice sheet is established, a moderate increase in insolation is sufficient to trigger a negative mass balance, leading to an almost complete retreat of the ice sheet within several thousand years. This fast retreat is governed mainly by rapid ablation due to the lowered surface elevation resulting from delayed isostatic rebound, which is the lithosphere-asthenosphere response. Carbon dioxide is involved, but is not determinative, in the evolution of the 100,000-year glacial cycles.

Forming Limit Diagram of Titanium and Stainless Steel Alloys to Study the Formability of Hydro-Mechanical Deep Drawing Parts

NASA Astrophysics Data System (ADS)

Shirizly, A.

2005-08-01

The increase demand for stronger, lighter and economic sheet metal products, make the Hydromecanical deep drawing process lately more and more popular. The Hydromecanical process is used in almost all types of sheet metal parts from home appliances and kitchenware to automotive and aviation industries. Therefore, many common materials were tested and characterized by their ability to sustain large strains via the well known Forming Limit Diagram (FLD). The aim of this work is to examine the forming capability if the Hydromecanical process in production of hemisphere parts made of materials commonly used in the aviation and aerospace industries. Experimental procedures were carried out to assess their ductility through FLD and the Forming Limit Carve (FLC).Two type of material sheets were tested herewith for demonstrating the procedure: commercial pure titanium and stainless steel 316L. A numerical simulation of the Hydromecanical process was examined and compared to self made Hydromecanical deep drawing of hemispherical parts.

Slicing of silicon into sheet material: Silicon sheet growth development for the large area silicon sheet task of the Low Cost Silicon Solar Array project

NASA Technical Reports Server (NTRS)

Fleming, J. R.

1978-01-01

The limits of blade tolerance were defined. The standard blades are T-2 thickness tolerance. Good results were obtained by using a slurry fluid consisting of mineral oil and a lubricity additive. Adjustments of the formulation and fine tuning of the cutting process with the new fluid are necessary. Test results and consultation indicate that the blade breakage encountered with water based slurries is unavoidable. Two full capacity (974 wafer) runs were made on the large prototype saw. Both runs resulted in extremely low yield. However, the reasons for the low yield were lack of proper technique rather than problems with machine function. The test on the effect of amount of material etched off of an as-sawn wafer on solar cell efficiency were completed. The results agree with previous work at JPL in that the minimum material removed per side that gives maximum efficiency is on the order of 10 microns.

Diagnosing Sporadic Creutzfeldt-Jakob Disease: Accuracy of CSF 14-3-3 Protein Test of the Spinal Fluid

MedlinePlus

... JAKOB DISEASE: ACCURACY OF THE 14-3-3 PROTEIN TEST OF THE SPINAL FLUID This information sheet ... help you understand how the 14-3-3 protein test helps in diagnosing sporadic Creutzfeldt-Jakob disease ( ...

Tensile strength of composite sheets with unidirectional stringers and crack-like damage

NASA Technical Reports Server (NTRS)

Poe, C. C., Jr.

1984-01-01

The damage tolerance characteristics of metal tension panels with riveted and bonded stringers are well known. The stringers arrest unstable cracks and retard propagation of fatigue cracks. Residual strengths and fatigue lives are considerably greater than those of unstiffened or integrally stiffened sheets. The damage tolerance of composite sheets with bonded composite stringers loaded in tension was determined. Cracks in composites do not readily propagate in fatigue, at least not through fibers. Moreover, the residual strength of notched composites is sometimes even increased by fatigue loading. Therefore, the residual strength aspect of damage tolerance, and not fatigue crack propagation, was investigated. About 50 graphite/epoxy composite panels were made with two sheet layups and several stringer configurations. Crack-like slots were cut in the middle of the panels to simulate damage. The panels were instrumented and monotonically loaded in tension to failure. The tests indicate that the composite panels have considerable damage tolerance, much like metal panels. The stringers arrested cracks that ran from the crack-like slots, and the residual strengths were considerably greater than those of unstiffened composite sheets. A stress intensity factor analysis was developed to predict the failing strains of the stiffened panels. Using the analysis, a single design curve was produced for composite sheets with bonded stringers of any configuration.

Increased Tensile Strength of Carbon Nanotube Yarns and Sheets through Chemical Modification and Electron Beam Irradiation

NASA Technical Reports Server (NTRS)

Miller, Sandi G.; Williams, Tiffany S.; Baker, James S.; Sola, Francisco; Lebron-Colon, Marisabel; McCorkle, Linda S.; Wilmoth, Nathan G.; Gaier, James; Chen, Michelle; Meador, Michael A.

2014-01-01

The inherent strength of individual carbon nanotubes offers considerable opportunity for the development of advanced, lightweight composite structures. Recent work in the fabrication and application of carbon nanotube (CNT) forms such as yarns and sheets has addressed early nanocomposite limitations with respect to nanotube dispersion and loading; and has pushed the technology toward structural composite applications. However, the high tensile strength of an individual CNT has not directly translated to macro-scale CNT forms where bulk material strength is limited by inter-tube electrostatic attraction and slippage. The focus of this work was to assess post processing of CNT sheet and yarn to improve the macro-scale strength of these material forms. Both small molecule functionalization and e-beam irradiation was evaluated as a means to enhance tensile strength and Youngs modulus of the bulk CNT material. Mechanical testing results revealed a tensile strength increase in CNT sheets by 57 when functionalized, while an additional 48 increase in tensile strength was observed when functionalized sheets were irradiated; compared to unfunctionalized sheets. Similarly, small molecule functionalization increased yarn tensile strength up to 25, whereas irradiation of the functionalized yarns pushed the tensile strength to 88 beyond that of the baseline yarn.

Investigation on bending failure to characterize crashworthiness of 6xxx-series aluminium sheet alloys with bending-tension test procedure

NASA Astrophysics Data System (ADS)

Henn, Philipp; Liewald, Mathias; Sindel, Manfred

2018-05-01

As lightweight design as well as crash performance are crucial to future car body design, exact material characterisation is important to use materials at their full potential and reach maximum efficiency. Within the scope of this paper, the potential of newly established bending-tension test procedure to characterise material crashworthiness is investigated. In this test setup for the determination of material failure, a buckling-bending test is coupled with a subsequent tensile test. If prior bending load is critical, tensile strength and elongation in the subsequent tensile test are dramatically reduced. The new test procedure therefore offers an applicable definition of failure as the incapacity of energy consumption in subsequent phases of the crash represents failure of a component. In addition to that, the correlation of loading condition with actual crash scenarios (buckling and free bending) is improved compared to three- point bending test. The potential of newly established bending-tension test procedure to characterise material crashworthiness is investigated in this experimental studys on two aluminium sheet alloys. Experimental results are validated with existing ductility characterisation from edge compression test.

40 CFR 60.533 - Compliance and certification.

Code of Federal Regulations, 2010 CFR

2010-07-01

..., including the complete test report and, for all test runs: Raw data sheets, laboratory technician notes... each test run in a certification test series, two photographs of the fuel load: One before and one... of blower motors and the fan blade size. (3) Any change in the materials used for the following...

40 CFR 60.533 - Compliance and certification.

Code of Federal Regulations, 2014 CFR

2014-07-01

..., including the complete test report and, for all test runs: Raw data sheets, laboratory technician notes... each test run in a certification test series, two photographs of the fuel load: One before and one... of blower motors and the fan blade size. (3) Any change in the materials used for the following...

40 CFR 60.533 - Compliance and certification.

Code of Federal Regulations, 2011 CFR

2011-07-01

..., including the complete test report and, for all test runs: Raw data sheets, laboratory technician notes... each test run in a certification test series, two photographs of the fuel load: One before and one... of blower motors and the fan blade size. (3) Any change in the materials used for the following...

40 CFR 60.533 - Compliance and certification.

Code of Federal Regulations, 2013 CFR

2013-07-01

..., including the complete test report and, for all test runs: Raw data sheets, laboratory technician notes... each test run in a certification test series, two photographs of the fuel load: One before and one... of blower motors and the fan blade size. (3) Any change in the materials used for the following...

40 CFR 60.533 - Compliance and certification.

Code of Federal Regulations, 2012 CFR

2012-07-01

..., including the complete test report and, for all test runs: Raw data sheets, laboratory technician notes... each test run in a certification test series, two photographs of the fuel load: One before and one... of blower motors and the fan blade size. (3) Any change in the materials used for the following...

The Hundred Pictures Naming Test. Pictures, Manual, and HPNT Response Sheet.

ERIC Educational Resources Information Center

Fisher, John P.; Glenister, Jennifer M.

Designed for use by speech pathologists, psychologists, special educators, English-as-a-Second-Language teachers, classroom teachers, and other professionals investigating child, adolescent, and adult language, this test--the Hundred Pictures Naming Test (HPNT)--is a confrontation naming test designed to evaluate rapid naming ability across age…

Culture-expanded mesenchymal stem cell sheets enhance extraction-site alveolar bone growth: An animal study.

PubMed

Mu, S; Tee, B C; Emam, H; Zhou, Y; Sun, Z

2018-04-06

Impaired bone formation of the buccal alveolar plate after tooth extraction during adolescence increases the difficulty of future implant restoration. This study was undertaken to assess the feasibility and efficacy of transplanting autogenous scaffold-free culture-expanded mesenchymal stem cell (MSC) sheets to the buccal alveolar bone surface to stimulate local bone growth. Mandibular bone marrow was aspirated from 3-month-old pigs (n = 5), from which MSCs were isolated and culture expanded. Triple-layer MSC sheets were then fabricated using temperature-responsive tissue culture plates. One month after bone marrow aspirations, the same pigs underwent bilateral extraction of mandibular primary molars, immediately followed by transplantation of 3 autogenous triple-layer MSC sheets on to the subperiosteal buccal alveolar surface of 1 randomly chosen side. The contralateral side (control) underwent the same periosteal reflection surgery without receiving MSC sheet transplantation. Six weeks later, the animals were killed and specimens from both sides were immediately harvested for radiographic and histological analysis. Buccal alveolar bone thickness, tissue mineral density (TMD), mineral apposition and bone volume fraction (BV/TV) were quantified and compared between the MSC sheet and control sides using paired t-tests. Triple-layer MSC sheets were reliably fabricated and the majority of cells remained vital before transplantation. The thickness of buccal bone tended to increase with MSC sheet transplantation (P = .18), with 4 of 5 animals showing an average of 1.82 ± 0.73 mm thicker bone on the MSC sheet side than the control side. After being normalized by the TMD of intracortical bone, the TMD of surface cortical bone was 0.5-fold higher on the MSC sheet side than the control side (P < .05). Likewise, the BV/TV measurements of the buccal surface region were also 0.4-fold higher on the MSC sheet side than the control side (P < .05) after being normalized by measurements from the intracortical region. Mineral apposition measurements were not different between the 2 sides. Mandibular marrow-derived MSCs can be fabricated into cell sheets and autogenous transplantation of MSC sheets onto the subperiosteal buccal alveolar bone surface at the tooth-extraction site may increase local bone density. © 2018 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Sensitivities of Greenland ice sheet volume inferred from an ice sheet adjoint model

NASA Astrophysics Data System (ADS)

Heimbach, P.; Bugnion, V.

2009-04-01

We present a new and original approach to understanding the sensitivity of the Greenland ice sheet to key model parameters and environmental conditions. At the heart of this approach is the use of an adjoint ice sheet model. Since its introduction by MacAyeal (1992), the adjoint method has become widespread to fit ice stream models to the increasing number and diversity of satellite observations, and to estimate uncertain model parameters such as basal conditions. However, no attempt has been made to extend this method to comprehensive ice sheet models. As a first step toward the use of adjoints of comprehensive three-dimensional ice sheet models we have generated an adjoint of the ice sheet model SICOPOLIS of Greve (1997). The adjoint was generated by means of the automatic differentiation (AD) tool TAF. The AD tool generates exact source code representing the tangent linear and adjoint model of the nonlinear parent model provided. Model sensitivities are given by the partial derivatives of a scalar-valued model diagnostic with respect to the controls, and can be efficiently calculated via the adjoint. By way of example, we determine the sensitivity of the total Greenland ice volume to various control variables, such as spatial fields of basal flow parameters, surface and basal forcings, and initial conditions. Reliability of the adjoint was tested through finite-difference perturbation calculations for various control variables and perturbation regions. Besides confirming qualitative aspects of ice sheet sensitivities, such as expected regional variations, we detect regions where model sensitivities are seemingly unexpected or counter-intuitive, albeit ``real'' in the sense of actual model behavior. An example is inferred regions where sensitivities of ice sheet volume to basal sliding coefficient are positive, i.e. where a local increase in basal sliding parameter increases the ice sheet volume. Similarly, positive ice temperature sensitivities in certain parts of the ice sheet are found (in most regions it is negativ, i.e. an increase in temperature decreases ice sheet volume), the detection of which seems highly unlikely if only conventional perturbation experiments had been used. An effort to generate an efficient adjoint with the newly developed open-source AD tool OpenAD is also under way. Available adjoint code generation tools now open up a variety of novel model applications, notably with regard to sensitivity and uncertainty analyses and ice sheet state estimation or data assimilation.

[Model oriented assessment of literacy performance in children with cochlear implants].

PubMed

Fiori, A; Reichmuth, K; Matulat, P; Schmidt, C M; Dinnesen, A G

2006-07-01

Although most hearing-impaired children lag behind normally hearing children in literacy acquisition, this aspect has hardly been addressed in the evaluation of language acquisition after cochlear implantation. The present study investigated written language abilities in 8 school-age children with cochlear implants. Neurolinguistic dual-route-models of written language processing indicate that literacy acquisition leads to the establishment of two distinct reading and writing strategies: a lexical one for the quick processing of known words and a sublexical one for decoding unfamiliar words or nonwords letter by letter. 8 school-aged children were investigated, a very heterogeneous group concerning age of onset of hearing impairment, educational placement, and competences in sign language. However, this range is typical of the group of CI-children. The aim was to investigate if children with cochlear implants are able to establish both strategies or if they need to find a differential and individual access to written language. Performance within the Salzburger Lese-Rechtschreib-Test was evaluated. Individual performance of each subject was analysed. Performance varied substantially ranging from only rudimentary spoken and written language abilities in two children to age-equivalent performance in three of them. Severe qualitative differences in written language processing were shown in the remaining three subjects. Suggestions for remediation were made and a re-test was carried out after 12 months. Their individual profiles of performance are described in detail. The present study stresses the importance of a thorough investigation of written language performance in the evaluation of language acquisition after cochlear implantation. The results draw a very heterogeneous picture of performance. Model-oriented testing and analysis of performance prove to be sensible in at least a subpopulation of children with cochlear implants. Based on a better understanding of their acquired word-processing strategies, remediation programs meeting the needs of each individual child can be derived.

40 CFR 160.105 - Test, control, and reference substance characterization.

Code of Federal Regulations, 2014 CFR

2014-07-01

... concomitantly according to written standard operating procedures, which provide for periodic analysis of each...) PESTICIDE PROGRAMS GOOD LABORATORY PRACTICE STANDARDS Test, Control, and Reference Substances § 160.105 Test...