Sunny Side Up in Mathematics.

ERIC Educational Resources Information Center

LaHart, David, Ed.

Energy is a problem affecting all individuals. To help today's students understand the problem and become realistic decision-makers, materials have been developed by the Sunny Side Up (in Mathematics) program to introduce energy concepts into the mathematics curriculum. Objectives of the program are to: (1) provide highly effective practice in…

In vivo bone strain in the mandibular corpus of Sapajus during a range of oral food processing behaviors.

PubMed

Ross, Callum F; Iriarte-Diaz, Jose; Reed, David A; Stewart, Thomas A; Taylor, Andrea B

2016-09-01

It has been hypothesized that mandibular corpus morphology of primates is related to the material properties of the foods that they chew. However, chewing foods with different material properties is accompanied by low levels of variation in mandibular strain patterns in macaques. We hypothesized that if variation in primate mandible form reflects adaptations to feeding on foods with different material and geometric properties, then this variation will be driven primarily by differences in oral food processing behavior rather than differences in chewing per se. To test this hypothesis, we recorded in vivo bone strain data from the lateral and medial surfaces of the mandibular corpus during complete feeding sequences in three adult male Sapajus as they fed on foods with a range of sizes and material properties. We assessed whether variation in mandibular corpus strain regimes is associated with variation in feeding behaviors and/or chewing on different foods, and we quantified the relative variation in mandibular corpus strain regimes associated with chewing on foods of different material properties versus a range of oral food processing behaviors (incisor, premolar, and molar biting; pulling on incisors; mastication). Feeding behavior had a significant effect on mandibular corpus strain regimes, as did chewing side and the cycle number in a feeding sequence. However, food type had weaker effects and usually only through interaction effects with chewing side and/or cycle type. Strain regimes varied most across different chew sides, then across different behaviors, and lastly between mastication cycles on different foods. Strain magnitudes associated with premolar, molar, and incisor biting were larger than those recorded during mastication. These data suggest that intra- and inter-specific variation in mandible morphology is a trade-off between performance requirements of different oral food processing behaviors and of variation in chewing side, with direct effects of food type being less important. Copyright © 2016 Elsevier Ltd. All rights reserved.

Ocular side effects of biological agents in oncology: what should the clinician be aware of?

PubMed Central

Hager, Tobias; Seitz, B

2014-01-01

During the last 20 years, biologicals have become increasingly relevant in oncologic therapy. Depending on the medication used, there are different profiles of ocular side effects. Although these can be present in up to 70% of patients, they are generally underreported in the literature. Therefore, the pathophysiological details of their development are often poorly understood. Herein we attempt to identify groups of biologicals to which a specific side effect profile can be assigned. We also tried to capture all relevant side effects and therefore conducted several database investigation including Medline, Cochrane library, and the drugs section of the US Food and Drug Administration (FDA), using the following search strings: “name of biological agent (both generic and commercial names)” AND “eye” OR “ocular”. If we found a side effect that has been associated with a drug, we researched Medline using the following search string: “name of biological agent” (both generic and commercial names) AND “term for the specific side effect”. Due to the wealth of material we report only the drugs that are approved by the FDA. PMID:24391443

An efficient mechanism for enhancing the thermoelectricity of nanoribbons by blocking phonon transport in 2D materials.

PubMed

Liu, Yue-Yang; Zeng, Yu-Jia; Jia, Pin-Zhen; Cao, Xuan-Hao; Jiang, Xiangwei; Chen, Ke-Qiu

2018-07-11

Inspired by the novel mechanism of reducing thermal conductivity by local phonon resonance instead of by inducing structural defects, we investigate the effect of side branching on the thermoelectric properties of [Formula: see text] nanoribbons, and prove that side branching is a highly efficient mechanism for enhancing the thermoelectricity of different kinds of nanoribbons. For both armchair and zigzag [Formula: see text] nanoribbons, the side branches result in not only significant blocking of phonon transport but also notable increase of the Seebeck coefficient. Consequently, the thermoelectric figure of merit of the armchair [Formula: see text] nanoribbon is boosted from 0.72 to as high as 1.93, and the originally non-thermoelectric metallic zigzag [Formula: see text] nanoribbon is turned into a thermoelectric material due to the appearance of the band gap induced by the side branches. These results mean that the mechanism of branching is not only very efficient, but also takes effect regardless of the original properties of the nanoribbons, and thus will hold great promise for its application in the thermoelectric field.

Chemical Retraction Agents - in vivo and in vitro Studies into their Physico-Chemical Properties, Biocompatibility with Gingival Margin Tissues and Compatibility with Elastomer Impression Materials.

PubMed

Nowakowska, Danuta; Saczko, Jolanta; Kulbacka, Julita; Wicckiewicz, Wlodzimierz

2017-01-01

Gingival margin retraction/displacement (GMR/D) is a commonly accepted procedure in restorative dentistry. Of the various retraction methods, the chemo-mechanical approach with retraction media and chemical retraction agents (ChRAs) is mostly used. Different local and/or systemic side effects were observed after "chemical attacks" from these retraction agents. Moreover, no consensus exists as to the compatibility of chemical agents with different impression materials. This paper reports the findings of in vivo and in vitro studies and we discuss the physico-chemical properties of chemical retraction agents, their undesirable clinical side effects, biological activity and compatibility with selected groups of elastomer impression materials. Copyright© Bentham Science Publishers; For any queries, please email at epub@benthamscience.org.

Effects of Alkylthio and Alkoxy Side Chains in Polymer Donor Materials for Organic Solar Cells.

PubMed

Cui, Chaohua; Wong, Wai-Yeung

2016-02-01

Side chains play a considerable role not only in improving the solubility of polymers for solution-processed device fabrication, but also in affecting the molecular packing, electron affinity and thus the device performance. In particular, electron-donating side chains show unique properties when employed to tune the electronic character of conjugated polymers in many cases. Therefore, rational electron-donating side chain engineering can improve the photovoltaic properties of the resulting polymer donors to some extent. Here, a survey of some representative examples which use electron-donating alkylthio and alkoxy side chains in conjugated organic polymers for polymer solar cell applications will be presented. It is envisioned that an analysis of the effect of such electron-donating side chains in polymer donors would contribute to a better understanding of this kind of side chain behavior in solution-processed conjugated organic polymers for polymer solar cells. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

The feedback control cycle as regulator of past and future mineral supply

NASA Astrophysics Data System (ADS)

Wellmer, Friedrich-W.; Dalheimer, Manfred

2012-10-01

Mineral supply is controlled by a feedback mechanism. When there is a shortage of a commodity in a market economy, prices will rise, triggering this mechanism. The expectation of high financial returns will encourage inventiveness and creativity in the quest for new solutions. On the supply side, for primary resources, the appropriate response is to cut losses in the mining process, to lower the cut-off grade, to improve recoveries in the beneficiation and smelting processes, to expand existing production facilities, and to discover and bring into production new deposits. For secondary resources, the key to increasing the supply lies in improving recycling rates by better technology, reprocessing lower-grade scrap which becomes economic because of increased prices, and reducing downgrading to optimize the usefulness of secondary materials. On the demand side, implementation of new and more efficient processes, development of substitution technologies, material savings, and the invention of entirely new technologies that fulfill the same function without the need of using the scarce and suddenly more expensive material are effective reactions to a price rise. The effectiveness of this self-regulating mechanism can be shown by examples of historical price peaks of metals, such as Mo, Co, and Ta, and the current rare earth elements peak. Concerning supply from secondary resources, a model is developed in order to determine how far the supply from this resource domain can be achieved and how the recycling rate is influenced by growth rate and lifetime. The feedback control cycle of mineral supply is influenced on the demand side by ever shorter life cycles, by products getting more complex with ever more elements involved in their production, and by an increase in element dispersion. All these factors have an immediate effect on the feasibility of sourcing raw materials from the technosphere. The supply side of primary materials is influenced by increasing lead times for new production and by relatively low flexibility in responding to changing demand.

Food and Natural Materials Target Mechanisms to Effectively Regulate Allergic Responses.

PubMed

Shin, Hee Soon; Shon, Dong-Hwa

2015-01-01

An immune hypersensitivity disorder called allergy is caused by diverse allergens entering the body via skin contact, injection, ingestion, and/or inhalation. These allergic responses may develop into allergic disorders, including inflammations such as atopic dermatitis, asthma, anaphylaxis, food allergies, and allergic rhinitis. Several drugs have been developed to treat these allergic disorders; however, long-term intake of these drugs could have adverse effects. As an alternative to these medicines, food and natural materials that ameliorate allergic disorder symptoms without producing any side effects can be consumed. Food and natural materials can effectively regulate successive allergic responses in an allergic chain-reaction mechanism in the following ways: [1] Inhibition of allergen permeation via paracellular diffusion into epithelial cells, [2] suppression of type 2 T-helper (Th) cell-related cytokine production by regulating Th1/Th2 balance, [3] inhibition of pathogenic effector CD4(+) T cell differentiation by inducing regulatory T cells (Treg), and [4] inhibition of degranulation in mast cells. The immunomodulatory effects of food and natural materials on each target mechanism were scientifically verified and shown to alleviate allergic disorder symptoms. Furthermore, consumption of certain food and natural materials such as fenugreek, skullcap, chitin/chitosan, and cheonggukjang as anti-allergics have merits such as safety (no adverse side effects), multiple suppressive effects (as a mixture would contain various components that are active against allergic responses), and ease of consumption when required. These merits and anti-allergic properties of food and natural materials help control various allergic disorders.

Induction soldering of photovoltaic system components

DOEpatents

Kumaria, Shashwat; de Leon, Briccio

2015-11-17

A method comprises positioning a pair of photovoltaic wafers in a side-by-side arrangement. An interconnect is placed on the pair of wafers such that the interconnect overlaps both wafers of the pair, solder material being provided between the interconnect and the respective wafers. A solder head is then located adjacent the interconnect, and the coil is energized to effect inductive heating of the solder material. The solder head comprises an induction coil shaped to define an eye, and a magnetic field concentrator located at least partially in the eye of the coil. The magnetic field concentrator defines a passage extending axially through the eye of the coil, and may be of a material with a high magnetic permeability.

Tuning Interfacial Thermal Conductance of Graphene Embedded in Soft Materials by Vacancy Defects

DOE PAGES

Liu, Ying; Hu, Chongze; Huang, Jingsong; ...

2015-06-23

Nanocomposites based on graphene dispersed in matrices of soft materials are promising thermal management materials. Their effective thermal conductivity depends on both the thermal conductivity of graphene and the conductance of the thermal transport across graphene-matrix interfaces. Here we report on molecular dynamics simulations of the thermal transport across the interfaces between defected graphene and soft materials in two different modes: in the across mode, heat enters graphene from one side of its basal plane and leaves through the other side; in the non-across mode, heat enters or leaves a graphene simultaneously from both sides of its basal plane. Wemore » show that, as the density of vacancy defects in graphene increases from 0 to 8%, the conductance of the interfacial thermal transport in the across mode increases from 160.4 16 to 207.8 11 MW/m2K, while that in the non-across mode increases from 7.2 0.1 to 17.8 0.6 MW/m2K. The molecular mechanisms for these variations of thermal conductance are clarified by using the phonon density of states and structural characteristics of defected graphenes. On the basis of these results and effective medium theory, we show that it is possible to enhance the effective thermal conductivity of thermal nanocomposites by tuning the density of vacancy defects in graphene despite the fact that graphene s thermal conductivity always decreases as vacancy defects are introduced.« less

Effect of phase change material on the heat transfer rate of different building materials

NASA Astrophysics Data System (ADS)

Hasan, Mushfiq; Alam, Shahnur; Ahmed, Dewan Hasan

2017-12-01

Phase change material (PCM) is widely known as latent heat storage. A comprehensive study is carried out to investigate the effect of PCM on heat transfer rate of building materials. Paraffin is used as PCM along with different conventional building materials to investigate the heat transfer rate from the heated region to the cold region. PCM is placed along with the three different types of building materials like plaster which is well know building material in urban areas and wood and straw which are commonly used in rural areas for roofing as well as wall panel material and investigated the heat transfer rate. An experimental setup was constructed with number of rectangular shape aluminum detachable casing (as cavity) and placed side by side. Series of rectangular cavity filled with convent ional building materials and PCM and these were placed in between two chambers filled with water at different temperature. Building materials and PCM were placed in different cavities with different combinations and investigated the heat transfer rate. The results show that using the PCM along with other building materials can be used to maintain lower temperature at the inner wall and chamber of the cold region. Moreover, the placement or orientation of the building materials and PCM make significant contribution to heat transfer rate from the heated zone to the cold zone.

Laser peening of components of thin cross-section

DOEpatents

Hackel, Lloyd A [Livermore, CA; Halpin, John M [Tracy, CA; Harris, Jr., Fritz B.

2003-12-02

The properties of a metal piece are altered by laser peening the piece on the first side using an acoustic coupling material operatively connected to the second side and subsequently laser peening the piece on the second side using an acoustic coupling material operatively connected to the first side

Laser Peening Of Components Of Thin Cross-Section

DOEpatents

Hackel, Lloyd A.; Halpin, John M.; Harris, Jr., Fritz B.

2004-10-19

The properties of a metal piece are altered by laser peening the piece on the first side using an acoustic coupling material operatively connected to the second side and subsequently laser peening the piece on the second side using an acoustic coupling material operatively connected to the first side.

Effects of Er:YAG laser irradiation on human dentin: polarizing microscopic, light microscopic and microradiographic observations, and FT-IR analysis.

PubMed

Ishizaka, Yaeko; Eguro, Toru; Maeda, Toru; Tanaka, Hisayoshi

2002-01-01

The effects of Er:YAG laser irradiation on dentin have not been sufficiently investigated. The purpose of this study was to investigate the effects of Er:YAG laser irradiation on dentin. After cavities were prepared using Er:YAG laser irradiation or rotary cutting instruments, histological observations of cavity-floor dentin utilizing polarizing microscopy, microradiography and light microscopy, and analysis of composition of cavity-floor dentin using Fourier-transformed (FT-IR) spectrometry were conducted. In the laser-treated side, a deeply stained basophilic layer was observed. The number of odontoblastic processes present was obviously less in the laser-treated side than in the bur-treated side. FT-IR analysis revealed that compared to the bur-treated side, a broad background peak at around 1,600 cm(-1) was present. Er:YAG laser irradiation might have denatured the organic materials of dentin. Copyright 2002 Wiley-Liss, Inc.

Strong liquid-crystalline polymeric compositions

DOEpatents

Dowell, Flonnie

1993-01-01

Strong liquid-crystalline polymeric (LCP) compositions of matter. LCP backbones are combined with liquid crystalline (LC) side chains in a manner which maximizes molecular ordering through interdigitation of the side chains, thereby yielding materials which are predicted to have superior mechanical properties over existing LCPs. The theoretical design of LCPs having such characteristics includes consideration of the spacing distance between side chains along the backbone, the need for rigid sections in the backbone and in the side chains, the degree of polymerization, the length of the side chains, the regularity of the spacing of the side chains along the backbone, the interdigitation of side chains in sub-molecular strips, the packing of the side chains on one or two sides of the backbone to which they are attached, the symmetry of the side chains, the points of attachment of the side chains to the backbone, the flexibility and size of the chemical group connecting each side chain to the backbone, the effect of semiflexible sections in the backbone and the side chains, and the choice of types of dipolar and/or hydrogen bonding forces in the backbones and the side chains for easy alignment.

Periodontal regenerative effect of a bovine hydroxyapatite/collagen block in one-wall intrabony defects in dogs: a histometric analysis

PubMed Central

Jung, Ui-Won; Lee, Jung-Seok; Park, Weon-Yeong; Cha, Jae-Kook; Hwang, Ji-Wan; Park, Jung-Chul; Kim, Chang-Sung; Cho, Kyoo-Sung; Chai, Jung-Kiu

2011-01-01

Purpose The aim of this study was to elucidate the effect of a bovine hydroxyapatite/collagen (BHC) block in one-wall intrabony periodontal defects in dogs. Methods A one-wall intrabony periodontal defect (4 mm wide and 5 mm deep) was prepared bilaterally at the mesial side of the mandibular fourth premolar in five beagle dogs. After thorough root planing, block-type BHC (4×5×5 mm) was placed on one side. The contralateral defect area did not receive any material as a sham-surgery control. Histological analysis of the sites was performed after an 8-week healing period. Results Two of five samples in the experimental group healed well without dissipation of the graft materials, and histological analysis revealed excellent regeneration of the periodontal tissues. However, most of the grafted materials had been displaced in the other three samples, leaving only a small portion of the graft. The measured parameters exhibited large standard deviations, and the mean values did not differ significantly between the experimental and sham-surgery control sides. Conclusions The application of BHC alone-without a barrier membrane-to wide, one-wall intrabony periodontal defects yielded inconsistent results regarding both periodontal regeneration and substantivity of the graft materials. Thus, the use of a barrier membrane for noncontained-type defects is recommended to improve the stability of the grafted material, and to condense it. PMID:22324006

The Association of Long-term Treatment-related Side Effects With Cancer-specific and General Quality of Life Among Prostate Cancer Survivors

PubMed Central

Davis, Kimberly M.; Kelly, Scott P.; Luta, George; Tomko, Catherine; Miller, Anthony B.; Taylor, Kathryn L.

2018-01-01

OBJECTIVE To examine the association between treatment-related side effects and cancer-specific and general quality of life (QOL) among long-term prostate cancer survivors. MATERIALS AND METHODS Within the Prostate, Lung, Colorectal and Ovarian Cancer Screening Trial, we conducted telephone interviews with prostate cancer survivors (N = 518) who were 5-10 years after diagnosis. We assessed demographic and clinical information, sexual, urinary, and bowel treatment-related side effects (Expanded Prostate Cancer Index Composite), cancer-specific QOL (Functional Assessment of Cancer Therapy—total score), and general QOL (the Medical Outcomes Study Short Form 12’s physical and mental subscales). RESULTS Participants were aged 74.6 years on average, primarily White (88.4%), and married (81.7%). Pearson correlation coefficients between the 3 treatment-related side effect domains (urinary, sexual, and bowel) and QOL ranged between 0.14 and 0.42 (P <.0001). Multivariable linear regression analyses revealed that poorer urinary and sexual functioning and greater bowel side effects were independently associated with poorer cancer-specific QOL (P <.0001). Bowel and urinary functions were also associated with poorer general QOL on the Medical Outcomes Study Short Form 12’s physical component summary and mental component summary (P <.05). Bowel side effects demonstrated the strongest association with all QOL outcomes. CONCLUSION Treatment-related side effects persisted for up to 10 years after diagnosis and continued to be associated with men’s QOL. These results suggest that each of the treatment-related side effects was independently associated with cancer-specific QOL. Compared with the other Expanded Prostate Cancer Index Composite domains, bowel side effects had the strongest association with cancer-specific and general QOL. These associations emphasize the tremendous impact that bowel side effects continue to have for men many years after their initial diagnosis. PMID:24975711

System for harvesting water wave energy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Zhong Lin; Su, Yanjie; Zhu, Guang

A generator for harvesting energy from water in motion includes a sheet of a hydrophobic material, having a first side and an opposite second side, that is triboelectrically more negative than water. A first electrode sheet is disposed on the second side of the sheet of a hydrophobic material. A second electrode sheet is disposed on the second side of the sheet of a hydrophobic material and is spaced apart from the first electrode sheet. Movement of the water across the first side induces an electrical potential imbalance between the first electrode sheet and the second electrode sheet.

Strong liquid-crystalline polymeric compositions

DOEpatents

Dowell, F.

1993-12-07

Strong liquid-crystalline polymeric (LCP) compositions of matter are described. LCP backbones are combined with liquid crystalline (LC) side chains in a manner which maximizes molecular ordering through interdigitation of the side chains, thereby yielding materials which are predicted to have superior mechanical properties over existing LCPs. The theoretical design of LCPs having such characteristics includes consideration of the spacing distance between side chains along the backbone, the need for rigid sections in the backbone and in the side chains, the degree of polymerization, the length of the side chains, the regularity of the spacing of the side chains along the backbone, the interdigitation of side chains in sub-molecular strips, the packing of the side chains on one or two sides of the backbone to which they are attached, the symmetry of the side chains, the points of attachment of the side chains to the backbone, the flexibility and size of the chemical group connecting each side chain to the backbone, the effect of semiflexible sections in the backbone and the side chains, and the choice of types of dipolar and/or hydrogen bonding forces in the backbones and the side chains for easy alignment. 27 figures.

The effectiveness of the controlled release of simvastatin from β-TCP macrosphere in the treatment of OVX mice.

PubMed

Chou, Joshua; Ito, Tomoko; Otsuka, Makoto; Ben-Nissan, Besim; Milthorpe, Bruce

2016-03-01

Simvastatin, a cholesterol treatment drug, has been shown to stimulate bone regeneration. As such, there has been an increase interest in the development of suitable materials and systems for the delivery of simvastatin. Without the appropriate dosage of simvastatin, the therapeutic effects on bone growth will be significantly reduced. Furthermore, similar to many pharmaceutical compounds, at high concentration simvastatin can cause various adverse side-effects. Given the associated side-effects with the usage of simvastatin, the development of suitable controlled drug release system is pertinent. Calcium phosphate in particularly beta-tricalcium phosphate (β-TCP) has been extensively studied and used as a carrier material for drug delivery system. In this study, Foraminifera exoskeletons were used as calcium carbonate precursor materials, which were hydrothermally converted to β-TCP as a carrier material for simvastatin. Natural marine exoskeletons posses interconnected and uniformly porous network capable of improving drug loading and release rate. To prolong the release of simvastatin, an apatite coating was made around the β-TCP sample and in vitro release studies in simulated body fluid (SBF) showed a significant decrease in release rate. Osteoporotic mice were used to examine the compare therapeutic effectiveness of β-TCP, β-TCP with simvastatin, apatite-coated β-TCP with simvastatin and direct injection of simvastatin near the right femur of the mice. Localized and systemic effect were compared with the femur of the non-implanted side (left) and showed that β-TCP with or without simvastatin was able to induce significant bone formation over 6 weeks. Mechanical analysis showed that apatite-coated β-TCP with simvastatin produced significantly stronger bones compared with other experimental groups. This study shows that natural exoskeletons with the appropriate structure can be successfully used as a drug delivery system for simvastatin and can its release can be prolonged with an apatite coating to significantly promote relevant bone formation. Copyright © 2013 John Wiley & Sons, Ltd.

Sound transmission through a double-panel construction lined with poroelastic material in the presence of mean flow

NASA Astrophysics Data System (ADS)

Zhou, Jie; Bhaskar, Atul; Zhang, Xin

2013-08-01

This paper investigates the sound transmission characteristics through a system of double-panel lined with poroelastic material in the core. The panels are surrounded by external and internal fluid media where a uniform external mean flow exists on one side. Biot's theory is used to model the porous material. Three types of constructions—bonded-bonded, bonded-unbonded and unbonded-unbonded—are considered. The effect of Mach number of the external flow on the sound transmission over a wide frequency range in a diffuse sound field is examined. External mean flow is shown to give a modest increase in transmission loss at low frequency, but a significant increase at high frequency. It is brought out that calculations based on static air on the incidence side provide a conservative estimate of sound transmission through the sandwich structure. The acoustic performance of the sandwich panel for different configurations is presented. The effect of curvature of the panel is also brought out by using shallow shell theory.

Effect of the Tin- versus Air-side Plate-glass Orientation on the Impact Response and Penetration Resistance of a Laminated Transparent Armour Structure

DTIC Science & Technology

2012-01-16

January 2012 2012 226:Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials Design and Applications M Grujicic, W C Bell...unclassified c . THIS PAGE unclassified Standard Form 298 (Rev. 8-98) Prescribed by ANSI Std Z39-18 Effect of the tin- versus air-side plate-glass...orientation on the impact response and penetration resistance of a laminated transparent armour structure M Grujicic1*, W C Bell1, B Pandurangan1, B

Potential of Eucalyptus Oil as Repellent against House Rat, Rattus rattus

PubMed Central

Thind, Ramandeep Kaur; Mahal, Amrit Kaur

2014-01-01

Rodent repellents are chemicals which by taste or odour or possibly by both will prevent animal from feeding or gnawing. Such substances may be used in protecting an area from rodent infestation or in protecting packaged food, packing materials, electric cables, and other important vulnerable materials. Mature and healthy house rat, Rattus rattus of both sexes, was exposed to 5, 10, and 20% eucalyptus oil applied as spray in laboratory pens in bichoice tests. Each concentration was applied through three different modes of application, that is, daily, once, and alternatively in a week. Repellent effect of the oil was assessed based on food consumption from treated and untreated sides for four days. In overall, food consumption was significantly (P < 0.0001) low from treatment side compared to the untreated side indicating significant repellent effect of the oil at all the three concentrations tested. Repellent effect of the oil was, however, not found to differ significantly between the two sexes. Percent repellency in both male and female rats was apparently more with daily application of 5 and 10% eucalyptus oil. Present studies reveal the potential of eucalyptus oil in repelling away R. rattus; however, further studies may be conducted to enhance the persistence of repellent effect for longer period of time. PMID:24523633

Prostate Cancer Information Available in Health-Care Provider Offices: An Analysis of Content, Readability, and Cultural Sensitivity.

PubMed

Choi, Seul Ki; Seel, Jessica S; Yelton, Brooks; Steck, Susan E; McCormick, Douglas P; Payne, Johnny; Minter, Anthony; Deutchki, Elizabeth K; Hébert, James R; Friedman, Daniela B

2018-07-01

Prostate cancer (PrCA) is the most common cancer affecting men in the United States, and African American men have the highest incidence among men in the United States. Little is known about the PrCA-related educational materials being provided to patients in health-care settings. Content, readability, and cultural sensitivity of materials available in providers' practices in South Carolina were examined. A total of 44 educational materials about PrCA and associated sexual dysfunction was collected from 16 general and specialty practices. The content of the materials was coded, and cultural sensitivity was assessed using the Cultural Sensitivity Assessment Tool. Flesch Reading Ease, Flesch-Kincaid Grade Level, and the Simple Measure of Gobbledygook were used to assess readability. Communication with health-care providers (52.3%), side effects of PrCA treatment (40.9%), sexual dysfunction and its treatment (38.6%), and treatment options (34.1%) were frequently presented. All materials had acceptable cultural sensitivity scores; however, 2.3% and 15.9% of materials demonstrated unacceptable cultural sensitivity regarding format and visual messages, respectively. Readability of the materials varied. More than half of the materials were written above a high-school reading level. PrCA-related materials available in health-care practices may not meet patients' needs regarding content, cultural sensitivity, and readability. A wide range of educational materials that address various aspects of PrCA, including treatment options and side effects, should be presented in plain language and be culturally sensitive.

Thermoelectric heat exchange element

DOEpatents

Callas, James J.; Taher, Mahmoud A.

2007-08-14

A thermoelectric heat exchange module includes a first substrate including a heat receptive side and a heat donative side and a series of undulatory pleats. The module may also include a thermoelectric material layer having a ZT value of 1.0 or more disposed on at least one of the heat receptive side and the heat donative side, and an electrical contact may be in electrical communication with the thermoelectric material layer.

Influence of backside loading on the floating mass transducer: An in vitro experimental study.

PubMed

Gostian, A-O; Otte, M S; Pazen, D; Ortmann, M; Schwarz, D; Hüttenbrink, K B; Beutner, D

2018-04-01

The vibration of the floating mass transducer (FMT) of a single active middle-ear implant (AMEI) is distinctly influenced by the properties of the material coupled to its back side. In round window vibroplasty, the FMT needs to be padded against the surrounding bone opposite from the round window membrane. This represents one factor influencing its performance as a round window driver. Therefore, we examined the effects of different materials linked to the back side of an FMT on its vibration range. The back side of an FMT was glued to a silicone cylinder 1.0 mm in diameter and 1.0 mm - 1.5 mm in length and of 40A, 50A or 70A Shore hardness; to cartilage of equivalent size; or to a round window soft coupler (RWSC), all firmly fixed on a steel plate. The vibrations were determined by a laser Doppler vibrometer (LDV) measuring the velocity of the centre point on the front side of the FMT. The materials on the back side of the FMT significantly influenced the vibration range of the FMT. The RWSC and silicone of 40A Shore hardness allowed for the highest detected velocities, while cartilage led to a distinct reduction similarly to 70A silicone. The coupling on the back side of an FMT distinctly affects its vibration range. In this regard, the RWSC and silicone of 40A Shore hardness yield the least impairment of vibration. Thus, the RWSC may be a feasible option in round window vibroplasty when additionally connected to the FMT opposite from the round window membrane. © 2017 John Wiley & Sons Ltd.

A facile electrode preparation method for accurate electrochemical measurements of double-side-coated electrode from commercial Li-ion batteries

NASA Astrophysics Data System (ADS)

Zhou, Ge; Wang, Qiyu; Wang, Shuo; Ling, Shigang; Zheng, Jieyun; Yu, Xiqian; Li, Hong

2018-04-01

The post mortem electrochemical analysis, including charge-discharge and electrochemical impedance spectroscopy (EIS) measurements, are critical steps for revealing the failure mechanisms of commercial lithium-ion batteries (LIBs). These post measurements usually require the reassembling of coin-cell with electrode which is often double-side-coated in commercial LIBs. It is difficult to use such double-side-coated electrode to perform accurate electrochemical measurements because the back side of the electrode is coated with active materials, rather than single-side-coated electrode that is often used in coin-cell measurements. In this study, we report a facile tape-covering sample preparation method, which can effectively suppress the influence of back side of the double-side-coated electrodes on capacity and EIS measurements in coin-cells. By tape-covering the unwanted side, the areal capacity of the desired investigated side of the electrode has been accurately measured with an experimental error of about 0.5% at various current densities, and accurate EIS measurements and analysis have been conducted as well.

Rim for rotary inertial energy storage device and method

DOEpatents

Knight, Jr., Charles E.; Pollard, Roy E.

1980-01-01

The present invention is directed to an improved rim or a high-performance rotary inertial energy storage device (flywheel). The improved rim is fabricated from resin impregnated filamentary material which is circumferentially wound in a side-by-side relationship to form a plurality of discretely and sequentially formed concentric layers of filamentary material that are bound together in a resin matrix. The improved rim is provided by prestressing the filamentary material in each successive layer to a prescribed tension loading in accordance with a predetermined schedule during the winding thereof and then curing the resin in each layer prior to forming the next layer for providing a prestress distribution within the rim to effect a self-equilibrating compressive prestress within the windings which counterbalances the transverse or radial tensile stresses generated during rotation of the rim for inhibiting deleterious delamination problems.

Changes in entrance surface dose in relation to the location of shielding material in chest computed tomography

NASA Astrophysics Data System (ADS)

Kang, Y. M.; Cho, J. H.; Kim, S. C.

2015-07-01

This study examined the effects of entrance surface dose (ESD) on the abdomen and pelvis of the patient when undergoing chest computed tomography (CT) procedure, and evaluated the effects of ESD reduction depending on the location of radiation shield. For CT scanner, the 64-slice multi-detector computed tomography was used. The alderson radiation therapy phantom and optically stimulated luminescence dosimeter (OSLD), which enabled measurement from low to high dose, were also used. For measurement of radiation dose, the slice number from 9 to 21 of the phantom was set as the test range, which included apex up to both costophrenic angles. A total of 10 OSLD nanoDots were attached for measurement of the front and rear ESD. Cyclic tests were performed using the low-dose chest CT and high-resolution CT (HRCT) protocol on the following set-ups: without shielding; shielding only on the front side; shielding only on the rear side; and shielding for both front and rear sides. According to the test results, ESD for both front and rear sides was higher in HRCT than low-dose CT when radiation shielding was not used. It was also determined that, compared to the set-up that did not use the radiation shield, locating the radiation shield on the front side was effective in reducing front ESD, while locating the radiation shield on the rear side reduced rear ESD level. Shielding both the front and rear sides resulted in ESD reduction. In conclusion, it was confirmed that shielding the front and rear sides was the most effective method to reduce the ESD effect caused by scatter ray during radiography.

How to improve patient education on deep brain stimulation in Parkinson's disease: the CARE Monitor study.

PubMed

Dinkelbach, Lars; Möller, Bettina; Witt, Karsten; Schnitzler, Alfons; Südmeyer, Martin

2017-02-21

The introduction of deep brain stimulation (DBS) about 25 years ago provided one of the major breakthroughs in the treatment of Parkinson's disease (PD). However, a high percentage of patients are reluctant to undergo DBS. Previous research revealed that the critical step on the patient's path to DBS is the decision whether to undergo further diagnostic assessment for surgery at a specialized DBS-center. The aims of the current study were to evaluate how effective the combination of an outpatient DBS screening tool, STIMULUS, with specially developed educational material was to enhance patient education on DBS and to identify motivational aspects which influenced the patients' willingness to undergo further assessment. In total, 264 patients were identified as appropriate candidates for DBS by general neurologists using the electronic preselection tool STIMULUS. Patient-centered information material was designed and handed out to support education on DBS. Further, several clinical characteristics and details of the patient counseling were documented. Refusal or consent to show up at a DBS center was registered over the following 16 months. 114 (43.2%) patients preselected as eligible for DBS (STIMULUS Score ≥ 6) agreed to show up at a specialized DBS center to undergo further diagnostic assessment. The patients' ages, PD classification as an akinetic-rigid type and the talks' topics side-effects of dopaminergic medication and the optimal time frame had a significant influence on the patients' decisions. The combination of preselection tools as STIMULUS with comprehensive information material is effective to increase DBS-acceptance rate in PD patients. Important topics of the information about DBS cover the optimal time frame for DBS surgery, the side-effects of dopaminergic medication as well as side-effects and complications of DBS surgery.

ETR CRITICAL FACILITY (ETRCF), TRA654. SOUTH SIDE. CAMERA FACING NORTH ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

ETR CRITICAL FACILITY (ETR-CF), TRA-654. SOUTH SIDE. CAMERA FACING NORTH AND ROLL-UP DOOR. ORIGINAL SIDING HAS BEEN REPLACED WITH STUCCO-LIKE MATERIAL. INL NEGATIVE NO. HD46-40-1. Mike Crane, Photographer, 4/2005 - Idaho National Engineering Laboratory, Test Reactor Area, Materials & Engineering Test Reactors, Scoville, Butte County, ID

Utilisation of polyurethane composit with 50% composition of roystonea regia fiber as noise reduction panel on car hood

NASA Astrophysics Data System (ADS)

Ikhwansyah; Mulia; Gunawan, S.; Lubis, R. D. W.

2018-02-01

The objective is to get the characteristics of noise reduction, noise reduction level, variety of measurement spaces, and knowing the process in making acoustic material of natural fiber becomes noise reduction on a car hood. The process of making noise reduction material used casting method and pressed by using molded press. The composition of noise reduction material consist of 50% roystonea regia by 32 mesh and 50% combined by gypsum and polyurethane. The result shows that the average result of noise reduction at X1- side is 5,7% and X2- side is 3,9%, X1+ side is 0,9% and X2+ side is 6,2%, Z1- side is 8,9% and Z2- side is 10,1%, Z1+ side is 9,7% and Z2+ side is 10,01%. The main conclusion of the study shows that a noise reduction which made of roystonea regia with 32 mesh mixed by matrix of polyurethane and gypsum is appropriate for noise reduction on car hood.

A PEG-Based Hydrogel for Effective Wound Care Management

PubMed Central

Chen, Sen-Lu; Fu, Ru-Huei; Liao, Shih-Fei; Liu, Shih-Ping; Lin, Shinn-Zong; Wang, Yu-Chi

2018-01-01

It is extremely challenging to achieve strong adhesion in soft tissues while minimizing toxicity, tissue damage, and other side effects caused by wound sealing materials. In this study, flexible synthetic hydrogel sealants were prepared based on polyethylene glycol (PEG) materials. PEG is a synthetic material that is nontoxic and inert and, thus, suitable for use in medical products. We evaluated the in vitro biocompatibility tests of the dressings to assess cytotoxicity and irritation, sensitization, pyrogen toxicity, and systemic toxicity following the International Organization for Standardization 10993 standards and the in vivo effects of the hydrogel samples using Coloskin liquid bandages as control samples for potential in wound closure. PMID:29637814

Method of Fabricating a Piezoelectric Composite Apparatus

NASA Technical Reports Server (NTRS)

Wilkie, W. Keats (Inventor); Bryant, Robert (Inventor); Fox, Robert L. (Inventor); Hellbaum, Richard F. (Inventor); High, James W. (Inventor); Jalink, Antony, Jr. (Inventor); Little, Bruce D. (Inventor); Mirick, Paul H. (Inventor)

2003-01-01

A method for fabricating a piezoelectric macro-fiber composite actuator comprises providing a piezoelectric material that has two sides and attaching one side upon an adhesive backing sheet. The method further comprises slicing the piezoelectric material to provide a plurality of piezoelectric fibers in juxtaposition. A conductive film is then adhesively bonded to the other side of the piezoelectric material, and the adhesive backing sheet is removed. The conductive film has first and second conductive patterns formed thereon which are electrically isolated from one another and in electrical contact with the piezoelectric material. The first and second conductive patterns of the conductive film each have a plurality of electrodes to form a pattern of interdigitated electrodes. A second film is then bonded to the other side of the piezoelectric material. The second film may have a pair of conductive patterns similar to the conductive patterns of the first film.

Long-Term Drainage from the Riprap Side Slope of a Surface Barrier

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Zhuanfang

Surface barriers designed to isolate underground nuclear waste in place are expected to function for at least 1000 years. To achieve this long design life, such barriers need to be protected with side slopes against wind- and water-induced erosion and damage by natural or human activities. However, the side slopes are usually constructed with materials coarser than the barrier. Their hydrological characteristics must be understood so that any drainage from them is considered in the barrier design and will not compromise the barrier function. The Prototype Hanford Barrier, an evapotranspiration-capillary (ETC) barrier, was constructed in 1994 at the Hanford Sitemore » in southeastern Washington state, with a gravel side slope and a riprap side slope. The soil water content in the gravel side slope and drainage from both side slopes have been monitored since the completion of construction. The monitoring results show that under natural precipitation the annual drainage rates from the two types of side slopes were very similar and about 5 times the typical recharge from local soil with natural vegetation and 40 times the barrier design criterion. The higher recharge from the side slopes results in some of the drainage migrating laterally to the region beneath the ETC barrier. This edge effect of the enhanced drainage was evaluated for a period of 1000 years by numerical simulation. The edge effect was quantified by the amount of water across the barrier edges and the affecting distance of the barrier edges. These results indicate that design features can be adjusted to reduce the edge effect when necessary.« less

Cassini Targets a Propeller in Saturn A Ring

NASA Image and Video Library

2017-03-02

NASA's Cassini spacecraft captured these remarkable views of a propeller feature in Saturn's A ring on Feb. 21, 2017. These are the sharpest images taken of a propeller so far, and show an unprecedented level of detail. The propeller is nicknamed "Santos-Dumont," after the pioneering Brazilian-French aviator. This observation was Cassini's first targeted flyby of a propeller. The views show the object from vantage points on opposite sides of the rings. The top image looks toward the rings' sunlit side, while the bottom image shows the unilluminated side, where sunlight filters through the backlit ring. The two images presented as figure 1 are reprojected at the same scale (0.13 mile or 207 meters per pixel) in order to facilitate comparison. The original images, which have slightly different scales, are also provided here, without reprojection, as figure 2; the sunlit-side image is at left, while the unlit-side image is at right. Cassini scientists have been tracking the orbit of this object for the past decade, tracing the effect that the ring has upon it. Now, as Cassini has moved in close to the ring as part of its ring-grazing orbits, it was able to obtain this extreme close-up view of the propeller, enabling researchers to examine its effects on the ring. These views, and others like them, will inform models and studies in new ways going forward. Like a frosted window, Saturn's rings look different depending on whether they are seen fully sunlit or backlit. On the lit side, the rings look darker where there is less material to reflect sunlight. On the unlit side, some regions look darker because there is less material, but other regions look dark because there is so much material that the ring becomes opaque. Observing the same propeller on both the lit and unlit sides allows scientists to gather richer information about how the moonlet affects the ring. For example, in the unlit-side view, the broad, dark band through the middle of the propeller seems to be a combination of both empty and opaque regions. The propeller's central moonlet would only be a couple of pixels across in these images, and may not actually be resolved here. The lit-side image shows that a bright, narrow band of material connects the moonlet directly to the larger ring, in agreement with dynamical models. That same thin band of material may also be obscuring the moonlet from view. Lengthwise along the propeller is a gap in the ring that the moonlet has pried open. The gap appears dark on both the lit and unlit sides. Flanking the gap near the moonlet are regions of enhanced density, which appear bright on the lit side and more mottled on the unlit side. One benefit of the high resolution of these images is that, for the first time, wavy edges are clearly visible in the gap. These waves are also expected from dynamical models, and they emphasize that the gap must be sharp-edged. Furthermore, the distance between the wave crests tells scientists the width of the gap (1.2 miles or 2 kilometers), which in turn reveals the mass of the central moonlet. From these measurements, Cassini imaging scientists deduce that the moonlet's mass is comparable to that of a snowball about 0.6 mile (1 kilometer) wide. For the original images, the lit-side image has a scale of 0.33 mile (530 meters) per pixel in the radial (or outward from Saturn) direction and 0.44 mile (710 meters) per pixel in the azimuthal (or around Saturn) direction. The different scales are the result of Cassini's vantage point being off to the side of the propeller, rather than directly above it. The unlit-side image has a scale of 0.25 (410 meters) per pixel in both directions. In order to preserve its original level of detail, the image has not been cleaned of bright blemishes due to cosmic rays and to charged particle radiation from Saturn. http://photojournal.jpl.nasa.gov/catalog/PIA21433

Optoelectronic device

DOEpatents

Bonekamp, Jeffrey E.; Boven, Michelle L.; Gaston, Ryan S.

2014-09-09

The invention is an optoelectronic device comprising an active portion which converts light to electricity or converts electricity to light, the active portion having a front side for the transmittal of the light and a back side opposite from the front side, at least two electrical leads to the active portion to convey electricity to or from the active portion, an enclosure surrounding the active portion and through which the at least two electrical leads pass wherein the hermetically sealed enclosure comprises at the front side of the active portion a barrier material which allows for transmittal of light, one or more getter materials disposed so as to not impede the transmission of light to or from the active portion, and a contiguous gap pathway to the getter material which pathway is disposed between the active portion and the barrier material.

Design of permanent magnet eddy current brake for a small scaled electromagnetic launch model

NASA Astrophysics Data System (ADS)

Zhou, Shigui; Yu, Haitao; Hu, Minqiang; Huang, Lei

2012-04-01

A variable pole-pitch double-sided permanent magnet (PM) linear eddy current brake (LECB) is proposed for a small scaled electromagnetic launch model. A two-dimensional (2D) analytical steady state model is presented for the double-sided PM-LECB, and the expression for the braking force is derived. Based on the analytical model, the material and eddy current skin effect of the conducting plate are analyzed. Moreover, a variable pole-pitch double-sided PM-LECB is proposed for the effective braking of the moving plate. In addition, the braking force is predicted by finite element (FE) analysis, and the simulated results are in good agreement with the analytical model. Finally, a prototype is presented to test the braking profile for validation of the proposed design.

Effects of processing parameters on the friction stir spot joining of Al5083-O aluminum alloy to DP590 steel

NASA Astrophysics Data System (ADS)

Sung, Back-Sub; Bang, Hee-Seon; Jeong, Su-Ok; Choi, Woo-Seong; Kwon, Yong-Hyuk; Bang, Han-Sur

2017-05-01

Two dissimilar materials, aluminum alloy Al5083-O and advanced high strength steel DP590, were successfully joined by using friction stir spot joining (FSSJ). Satisfactory joint strengths were obtained at a rotational speed of 300 rpm and a plunge depth of 0.7 mm. Resulting joints were welded without a non-welded zone. This may be attributed to the enhanced smooth material flow owing to sufficient stirring effect and tool down force between the upper Al5083-O side and the lower DP590 side. The maximum tensile shear strength was 6.5 kN, which was higher than the joint strength required by the conventional method of resistance spot welding. The main fracture mode was plug fracture in the tensile shear test of joints. An intermetallic compound (IMC) layer with <6 μm thickness was formed at the joint interface, which meets the allowance value of <10 μm for the dissimilar material Al-Fe joints. Thus, the use of FSSJ to weld the dissimilar materials Al5083-O and DP590 resulted in mechanically and metallurgically sound joints.

Some results of the oxidation investigation of copper and silver samples flown on LDEF

NASA Technical Reports Server (NTRS)

Derooij, A.

1992-01-01

The Long Duration Exposure Facility (LDEF) Mission provides a unique opportunity to study the long term effects of the space environment on materials. The LDEF has been deployed in orbit on 7 April 1984 by the shuttle Challenger in an almost circular orbit with a mean altitude of 477 km and an inclination of 28.5 degrees. It was retrieved from its decayed orbit of 335 km by the shuttle Columbia on 12 January 1990 after almost 6 years in space. The LDEF is a 12-sided, 4.267 m diameter, and 9.144 m long structure. The experiments, placed on trays, are attached to the twelve sides and the two ends of the spacecraft. The LDEF was passively stabilized with one end of the spacecraft always pointing towards the earth center and one of the sides (row 9) always facing the flight direction. The materials investigated originate from the Ultra-Heavy Cosmic Ray Experiment (UHCRE). The main objective is a detailed study of the charge spectra of ultraheavy cosmic-ray nuclei from zinc to uranium and beyond, using solid-state track detectors. Besides the aluminium alloy used for the experiment, UHCRE comprises several other materials. The results of space exposure for two of them, the copper grounding strips and the thermal covers (FEP Teflon/Ag/Inconel) painted black on the inner side (Chemglaze Z306), are presented.

Complementary π-π interactions induce multicomponent coassembly into functional fibrils.

PubMed

Ryan, Derek M; Doran, Todd M; Nilsson, Bradley L

2011-09-06

Noncovalent self-assembled materials inspired by amyloid architectures are useful for biomedical applications ranging from regenerative medicine to drug delivery. The selective coassembly of complementary monomeric units to provide ordered multicomponent fibrils is a possible strategy for enhancing the sophistication of these noncovalent materials. Herein we report that complementary π-π interactions can be exploited to promote the coassembly of phenylalanine (Phe) derivatives that possess complementary aromatic side-chain functionality. Specifically, equimolar mixtures of Fmoc-Phe and Fmoc-F(5)-Phe, which possess side-chain groups with complementary quadrupole electronics, readily coassemble to form two-component fibrils and hydrogels under conditions where Fmoc-Phe alone fails to self-assemble. In addition, it was found that equimolar mixtures of Fmoc-Phe with monohalogenated (F, Cl, and Br) Fmoc-Phe derivatives also coassembled into two-component fibrils. These results collectively indicate that face-to-face quadrupole stacking between benzyl side-chain groups does not account for the molecular recognition between Phe and halogenated Phe derivatives that promote cofibrillization but that coassembly is mediated by more subtle π-π effects arising from the halogenation of the benzyl side chain. The use of complementary π-π interactions to promote the coassembly of two distinct monomeric units into ordered two-component fibrils dramatically expands the repertoire of noncovalent interactions that can be used in the development of sophisticated noncovalent materials. © 2011 American Chemical Society

Allergic effects of the residual monomer used in denture base acrylic resins

PubMed Central

Rashid, Haroon; Sheikh, Zeeshan; Vohra, Fahim

2015-01-01

Denture base resins are extensively used in dentistry for a variety of purposes. These materials can be classified as chemical, heat, light, and microwave polymerization materials depending upon the factor which starts the polymerization reaction. Their applications include use during denture base construction, relining existing dentures, and for fabrication of orthodontic removable appliances. There have been increased concerns regarding the safe clinical application of these materials as their biodegradation in the oral environment leads to harmful effects. Along with local side effects, the materials have certain occupational hazards, and numerous studies can be found in the literature mentioning those. The purpose of this article is to outline the cytotoxic consequences of denture base acrylic resins and clinical recommendations for their use. PMID:26929705

Differential Curing In Fiber/Resin Laminates

NASA Technical Reports Server (NTRS)

Webster, Charles N.

1989-01-01

Modified layup schedule counteracts tendency toward delamination. Improved manufacturing process resembles conventional process, except prepregs partially cured laid on mold in sequence in degree of partial cure decreases from mold side to bag side. Degree of partial cure of each layer at time of layup selected by controlling storage and partial-curing temperatures of prepreg according to Arrhenius equation for rate of gel of resin as function of temperature and time from moment of mixing. Differential advancement of cure in layers made large enough to offset effect of advance bag-side heating in oven or autoclave. Technique helps prevent entrapment of volatile materials during manufacturing of fiber/resin laminates.

Toxicity and efficiency study of plant extracts-based bleaching agents.

PubMed

Baldea, Ioana; Olteanu, Diana Elena; Filip, Adriana Gabriela; Cenariu, Mihai; Dudea, Diana; Tofan, Alina; Alb, Camelia; Moldovan, Marioara

2017-05-01

Tooth bleaching is one of the most required dental esthetic treatments. However, it can generate side effects like oral irritation, enamel alteration, tooth sensitivity, especially caused by hydrogen peroxide, the main bleaching component of the commercial products. Therefore, development of new tooth bleaching agents, based on natural products, with comparable esthetic results and lower side effects is needed. The aim of this study was to evaluate the biological effects and bleaching efficacy of four experimental bleaching agents, derived from fruit juices, against the commercially available Opalescence (Ultradent, USA). Organic acid composition of the gels was characterized by HPLC. Bleaching efficiency was tested by spectrophotometry on composite restorative materials. Biological testing was done in vitro, on human fibroblasts. Cells were exposed to dilutions of the bleaching gel-conditioned medium. Viability was measured by MTS, apoptosis by FACS-AnnexinV FITC/Propidium iodide, NF-kB activation by western blot, malondyaldehide, and superoxide dismutase activity by spectrophotometry. All gels exhibited physical stability and dental bleaching capabilities. Experimental gels induced significantly better viability and apoptosis rates, lower lipid peroxidation, and increased antioxidant defense, compared to Opalescence. The studied experimental gel formulations exhibited a good safety profile in vitro, as well as bleaching efficiency on restorative composite materials. These data open new possibilities for the use of new natural products in dental bleaching treatments that can insure significant esthetic results and lower side effects.

Fear appeals and treatment side-effects: an effective combination for HIV prevention?

PubMed

Slavin, S; Batrouney, C; Murphy, D

2007-01-01

Recent rises in the incidence of HIV infections among gay men in Australia have produced widespread discussion about appropriate health promotion responses. This has sometimes included calls for a return to fear-based campaigns, exemplified by the Grim Reaper advertisements in HIV. This paper discusses results from four focus groups that tested mock campaign material based on an appeal to fear. Five different poster images were tested among groups distinguished by age and HIV serostatus. Three posters used side-effects from treatments as the fear trigger and two used death from AIDS. A number of themes arose in response to the material including 'othering', shame and scepticism about HIV treatments. The meanings of these themes are explored in the light of current health-promotion theory. This data demonstrates that fear is an ineffective tool for HIV health promotion. It further demonstrates that feelings of shame and stigma are likely to be exacerbated in gay men, leading to poorer health outcomes in various ways.

Thin film memory matrix using amorphous and high resistive layers

NASA Technical Reports Server (NTRS)

Thakoor, Anilkumar P. (Inventor); Lambe, John (Inventor); Moopen, Alexander (Inventor)

1989-01-01

Memory cells in a matrix are provided by a thin film of amorphous semiconductor material overlayed by a thin film of resistive material. An array of parallel conductors on one side perpendicular to an array of parallel conductors on the other side enable the amorphous semiconductor material to be switched in addressed areas to be switched from a high resistance state to a low resistance state with a predetermined level of electrical energy applied through selected conductors, and thereafter to be read out with a lower level of electrical energy. Each cell may be fabricated in the channel of an MIS field-effect transistor with a separate common gate over each section to enable the memory matrix to be selectively blanked in sections during storing or reading out of data. This allows for time sharing of addressing circuitry for storing and reading out data in a synaptic network, which may be under control of a microprocessor.

Insulation Test Cryostat with Lift Mechanism

NASA Technical Reports Server (NTRS)

Dokos, Adam G. (Inventor); Fesmire, James E. (Inventor)

2014-01-01

A multi-purpose, cylindrical thermal insulation test apparatus is used for testing insulation materials and systems of materials using a liquid boil-off calorimeter system for absolute measurement of the effective thermal conductivity (k-value) and heat flux of a specimen material at a fixed environmental condition (cold-side temperature, warm-side temperature, vacuum pressure level, and residual gas composition). The apparatus includes an inner vessel for receiving a liquid with a normal boiling point below ambient temperature, such as liquid nitrogen, enclosed within a vacuum chamber. A cold mass assembly, including the upper and lower guard chambers and a middle test vessel, is suspended from a lid of the vacuum canister. Each of the three chambers is filled and vented through a single feedthrough. All fluid and instrumentation feedthroughs are mounted and suspended from a top domed lid to allow easy removal of the cold mass. A lift mechanism allows manipulation of the cold mass assembly and insulation test article.

Insulation Test Cryostat with Lift Mechanism

NASA Technical Reports Server (NTRS)

Fesmire, James E. (Inventor); Dokos, Adam G. (Inventor)

2016-01-01

A multi-purpose, cylindrical thermal insulation test apparatus is used for testing insulation materials and systems of materials using a liquid boil-off calorimeter system for absolute measurement of the effective thermal conductivity (k-value) and heat flux of a specimen material at a fixed environmental condition (cold-side temperature, warm-side temperature, vacuum pressure level, and residual gas composition). An inner vessel receives liquid with a normal boiling point below ambient temperature, such as liquid nitrogen, enclosed within a vacuum chamber. A cold mass assembly, including upper and lower guard chambers and middle test vessel, is suspended from a lid of the vacuum canister. Each of the three chambers is filled and vented through a single feedthrough. All fluid and instrumentation feedthroughs are mounted and suspended from a top domed lid allowing easy removal of the cold mass. A lift mechanism allows manipulation of the cold mass assembly and insulation test article.

The effect of buccal corticotomy on accelerating orthodontic tooth movement of maxillary canine

PubMed Central

Jahanbakhshi, Mohammad Reza; Motamedi, Ali Mohammad Kalantar; Feizbakhsh, Masoud; Mogharehabed, Ahmad

2016-01-01

Background: Selective alveolar corticotomy is defined as an intentional injury to cortical bone. This technique is an effective means of accelerating orthodontic tooth movement. The aim of this study is to evaluate the effect of buccal corticotomy in accelerating maxillary canine retraction. Materials and Methods: The sample in this clinical trial study consisted of 15 adult female patients with therapeutic need for extraction of maxillary first premolars and maximum canine retraction. By use of split-mouth design, at the time of premolars extraction, buccal corticotomy was performed around the maxillary first premolar, randomly on one side of maxilla, and the other side was reserved as the control side. Canine retraction was performed by use of friction – less mechanic with simple vertical loop. Every 2 weeks, distance between canines and second premolars was measured until complete space closure. The velocity of space closure was calculated to evaluate the effect of this technique in accelerating orthodontic tooth movement. The obtained data were statistically analyzed using independent t-test, and the significance was set at 0.05. Results: The rate of canine retraction was significantly higher on the corticotomy side than the control side by an average of 1.8 mm/month versus 1.1 mm/month in the corticotomy side and control side, respectively (P < 0.001). Conclusion: Based on result of this study, corticotomy can accelerates the rate of orthodontic tooth movement about two times faster than conventional orthodontics and it is significant in early stages after surgical porsedure. Therefore Buccal corticotomy is a useful adjunct technique for accelerating orthodontic tooth movement. PMID:27605986

Molecular engineering to improve carrier lifetimes for organic photovoltaic devices with thick active layers

DOE PAGES

Oosterhout, Stefan D.; Braunecker, Wade A.; Owczarczyk, Zbyslaw R.; ...

2017-04-27

The morphology of the bulk heterojunction absorber layer in an organic photovoltaic (OPV) device has a profound effect on the electrical properties and efficiency of the device. Previous work has consistently demonstrated that the solubilizing side-chains of the donor material affect these properties and device performance in a non-trivial way. Here, using Time-Resolved Microwave Conductivity (TRMC), we show by direct measurements of carrier lifetimes that the choice of side chains can also make a substantial difference in photocarrier dynamics. We have previously demonstrated a correlation between peak photoconductance measured by TRMC and device efficiencies; here, we demonstrate that TRMC photocarriermore » dynamics have an important bearing on device performance in a case study of devices made from donor materials with linear vs. branched side-chains and with variable active layer thicknesses. We use Grazing-Incidence Wide Angle X-ray Scattering to elucidate the cause of the different carrier lifetimes as a function of different aggregation behavior in the polymers. Consequently, the results help establish TRMC as a technique for screening OPV donor materials whose devices maintain performance in thick active layers (>250 nm) designed to improve light harvesting, film reproducibility, and ease of processing.« less

Right-sided infective endocarditis: recent epidemiologic changes

PubMed Central

Yuan, Shi-Min

2014-01-01

Background: Infective endocarditis (IE) has been increasingly reported, however, little is available regarding recent development of right-sided IE. Methods: Right-sided IE was comprehensively analyzed based on recent 5⅓-year literature. Results: Portal of entry, implanted foreign material, and repaired congenital heart defects were the main predisposing risk factors. Vegetation size on the right-sided valves was much smaller than those beyond the valves. Multiple logistic regression analysis revealed that predisposing risk factors, and vegetation size and locations were independent predictive risks of patients’ survival. Conclusions: Changes of right-sided IE in the past 5⅓ years included younger patient age, and increased vegetation size, but still prominent Staphylococcus aureus infections. Complication spectrum has changed into more valve insufficiency, more embolic events, reduced abscess formation, and considerably decreased valve perforations. With effective antibiotic regimens, prognoses of the patients seemed to be better than before. PMID:24482708

Pleated metal bipolar assembly

DOEpatents

Wilson, Mahlon S.; Zawodzinski, Christine

2001-01-01

A thin low-cost bipolar plate for an electrochemical cell is formed from a polymer support plate with first flow channels on a first side of the support plate and second flow channels on a second side of the support plate, where the first flow channels and second flow channels have intersecting locations and have a depth effective to form openings through the support plate at the intersecting locations. A first foil of electrically conductive material is pressed into the first flow channels. A second foil of electrically conductive material pressed into the second flow channels so that electrical contact is made between the first and second foils at the openings through the support plate. A particular application of the bipolar plate is in polymer electrolyte fuel cells.

Pentosan Polysulfate

MedlinePlus

Pentosan polysulfate comes as a capsule to take by mouth. It is usually taken with water three times a day, 1 hour before or 2 hours after ... stools bloody vomit vomiting material that looks like coffee grounds Pentosan polysulfate may cause other side effects. ...

Problems associated with restorative materials--dentists' views in Finland and Sweden.

PubMed

Widström, E; Sundberg, H

1991-01-01

During the past 10-15 years the possible side-effects of dental restorative materials, especially due to amalgam fillings, have caused a lively debate in Sweden. There is an extensive literature on the chemical and biological properties of dental materials but no investigations have dealt with the providers' attitudes. The purpose of this study was to find out the dentists' experiences of and attitudes to patients who state they have problems related to dental restorative materials and compare the dentists' subjective assessments of those side-effects in two neighboring countries, Finland and Sweden. Information was collected by postal questionnaires addressed to dentists chosen at random in Finland (n = 625) and in Sweden (n = 960). The response rate was 73 per cent and 72 per cent respectively. The results showed that 99 per cent of the respondents had patients questioning the safety of dental materials. The number of such patients was estimated to be three times higher in Sweden (124 patients per dentist in 1989) than in Finland (39 patients per dentist). More than 90 per cent of the questions from the patients regarded amalgam fillings. Statistically significant differences were found between the respondents' opinions of amalgam, 81 per cent of the Finnish contrary to 59 per cent of the Swedish respondents considered the risk of side-effects to be low when using this material. About 90 per cent of the respondents considered glass-ionomer, gold and ceramic restorations safe, but only half of them were convinced of the safety of composite. A great majority of the Swedish respondents (79 per cent) claimed that the patients should get their fillings changed without odontologic indications if they insisted on it and paid for the treatment in comparison to 22 per cent of the Finnish respondents (p less than 0.001). In case dental insurance was to pay for this kind of treatment it was accepted by 6 per cent of the Finns and 25 per cent of the Swedes. The attitude to amalgam was in general less favorable among the dentists in Sweden than in Finland.

Fluorinated tin oxide back contact for AZTSSe photovoltaic devices

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gershon, Talia S.; Gunawan, Oki; Haight, Richard A.

A photovoltaic device includes a substrate, a back contact comprising a stable low-work function material, a photovoltaic absorber material layer comprising Ag.sub.2ZnSn(S,Se).sub.4 (AZTSSe) on a side of the back contact opposite the substrate, wherein the back contact forms an Ohmic contact with the photovoltaic absorber material layer, a buffer layer or Schottky contact layer on a side of the absorber layer opposite the back contact, and a top electrode on a side of the buffer layer opposite the absorber layer.

Finite element analysis of stress-breaking attachments on maxillary implant-retained overdentures.

PubMed

Tanino, Fuminori; Hayakawa, Iwao; Hirano, Shigezo; Minakuchi, Shunsuke

2007-01-01

The purpose of this study was to examine the effect of stress-breaking attachments at the connections between maxillary palateless overdentures and implants. Three-dimensional finite element models were used to reproduce an edentulous human maxilla with an implant-retained overdenture. Two-implant models (in the canine tooth positions on both sides) and four-implant models (in the canine and second premolar tooth positions on both sides) were examined. Stress-breaking material connecting the implants and denture was included around each abutment. Axial loads of 100 N were applied to the occlusal surface at the left first molar tooth positions. In each model, the influence of the stress-breaking attachments was compared by changing the elastic modulus from 1 to 3,000 MPa and the thickness of the stress-breaking material from 1 to 3 mm. Maximum stress at the implant-bone interface and stress at the cortical bone surface just under the loading point were calculated. In all models, maximum stress at the implant-bone interface with implants located in the canine tooth position was generated at the peri-implant bone on the loading side. As the elastic modulus of the stress-breaking materials increased, the stress increased at the implant-bone interface and decreased at the cortical bone surface. Moreover, stress at the implant-bone interface with 3-mm-thick stress-breaking material was smaller than that with 1-mm-thick material. Within the limitations of this experiment, stress generated at the implant-bone interface could be controlled by altering the elastic modulus and thickness of the stress-breaking materials.

MULCHES AND OTHER COVER MATERIALS TO REDUCE WEED GROWTH IN CONTAINER-GROWN NURSERY STOCK.

PubMed

Rys, F; Van Wesemael, D; Van Haecke, D; Mechant, E; Gobin, B

2014-01-01

Due to the recent EU-wide implementation of Integrated Pest Management (IPM), alternative methods to reduce weed growth in container-grown nursery stock are needed to cut back the use of herbicides. Covering the upper layer of the substrate is known as a potential method to prevent or reduce weed growth in plant containers. As a high variety of mulches and other cover materials are on the market, however, it is no longer clear for growers which cover material is most efficient for use in containers. Therefore, we examined the effect on weed growth of different mulches and other cover materials, including Pinus maritima, P. sylvestris, Bio-Top Basic, Bio-Top Excellent, coco chips fine, hemp fibres, straw pellets, coco disk 180LD and jute disk. Cover materials were applied immediately after repotting of Ligustrum ovalifolium or planting of Fagus sylvatica. At regular times, both weed growth and side effects (e.g., plant growth, water status of the substrate, occurrence of mushrooms, foraging of birds, complete cover of the substrate and fixation) were assessed. All examined mulches or other cover materials were able to reduce weed growth on the containers during the whole growing season. Weed suppression was even better than that of a chemical treated control. Although all materials showed some side effects, the impact on plant growth is most important to the grower and depends not only on material characteristics (e.g., biodegradation, nutrient leaching and N-immobilisation) but also on container size and climatic conditions. In conclusion, mulches and other cover materials can be a valuable tool within IPM to lower herbicide use. To enable a deliberate choice of which cover material is best used in a specific situation more research is needed on lifespan and stability as well as on economic characteristics of the materials.

Performance of PIN-PMN-PT Single Crystal Piezoelectric versus PZT8 Piezoceramic Materials in Ultrasonic Transducers

NASA Astrophysics Data System (ADS)

DeAngelis, D. A.; Schulze, G. W.

The recent advancements in the manufacturing of single crystal PIN-PMN-PT piezoelectric materials now make them a cost-competitive alternative to PZT4 and PZT8 (Navy Types I and III) piezoceramic materials, which have been the workhorse of power ultrasonic applications (e.g., welding, cutting, sonar, etc.) for over 50 years. Although there are great benefits to the use of single crystal materials with respect to high output, as well as added actuating and sensing abilities, many transducer designers are still reluctant to explore these materials due to inadequate design guidelines for substituting the familiar PZT materials; for example, what are the implications of the higher capacitance, sensitivity to chipping/cracks, aging effects, frequency shifts, or how much preload can be used are all common questions. This research is a case study on the performance of identical ultrasonic transducer bodies, used for semiconductor wire bonding, assembled with either PZT8 or PIN-PMN-PT piezo material. The main purpose of the study is to establish rule-of-thumb design guidelines for direct substitution of single crystal materials in existing PZT8 transducer designs, along with a side-by-side performance comparison to highlight benefits. Several metrics are investigated such as impedance, frequency, displacement gain, quality factor and electromechanical coupling factor.

New Eddy Current Probe for Thickness Gauging of Conductive Materials

NASA Technical Reports Server (NTRS)

Wincheski, Buzz; Fulton, Jim; Nath, Shridhar; Namkung, Min

1993-01-01

The accurate measure of material thickness is important for many non-destructive evaluation applications. Factors such as corrosion damage can jeopardize structural integrity through material thinning and process control considerations often mandate strict limits on material dimensions. Access to the material under test can be limited to a single side and large areas may need to be examined in a small time period. In an effort to enhance the effectiveness of material thickness measurements a flux focusing eddy current probe has been developed at NASA Langley Research Center. The probe provides an accurate measure of the thickness of conducting materials from a single sided measurement. It is straight forward to use and can be easily automated for production line testing. The probe also requires only minimal instrumentation and power so that extremely portable units can be manufactured at a low cost. This new eddy current probe has been used to accurately measure the thickness of aluminum alloy plates with a resolution of greater than 0.001 in. (25 microns). Simulated corrosion damage has also been detected on both single layer and multi-layer samples. The present work will explain the output voltage dependence of the device as a function of material thickness and present experimental results for thickness gauging and corrosion detection.

An Empirical Investigation of Organizational Effectiveness and Performance.

DTIC Science & Technology

1983-07-29

on rerie side II necessaIr and Identify by block nuIb*’) Organizational Effectiveness Model of Effectiveness Corporate Strategy Organizational...complex and problematic task with little likelihood of reaching a final or even acceptable solution, social science research, never-the-less, should...regulations, interest rates, the weather, availability of supplies and raw materials, changing social values, and other external organizational events

Aqueous Processing for Printed Organic Electronics: Conjugated Polymers with Multistage Cleavable Side Chains

PubMed Central

2017-01-01

The ability to process conjugated polymers via aqueous solution is highly advantageous for reducing the costs and environmental hazards of large scale roll-to-roll processing of organic electronics. However, maintaining competitive electronic properties while achieving aqueous solubility is difficult for several reasons: (1) Materials with polar functional groups that provide aqueous solubility can be difficult to purify and characterize, (2) many traditional coupling and polymerization reactions cannot be performed in aqueous solution, and (3) ionic groups, though useful for obtaining aqueous solubility, can lead to a loss of solid-state order, as well as a screening of any applied bias. As an alternative, we report a multistage cleavable side chain method that combines desirable aqueous processing attributes without sacrificing semiconducting capabilities. Through the attachment of cleavable side chains, conjugated polymers have for the first time been synthesized, characterized, and purified in organic solvents, converted to a water-soluble form for aqueous processing, and brought through a final treatment to cleave the polymer side chains and leave behind the desired electronic material as a solvent-resistant film. Specifically, we demonstrate an organic soluble polythiophene that is converted to an aqueous soluble polyelectrolyte via hydrolysis. After blade coating from an aqueous solution, UV irradiation is used to cleave the polymer’s side chains, resulting in a solvent-resistant, electroactive polymer thin film. In application, this process results in aqueous printed materials with utility for solid-state charge transport in organic field effect transistors (OFETs), along with red to colorless electrochromism in ionic media for color changing displays, demonstrating its potential as a universal method for aqueous printing in organic electronics. PMID:28979937

Aqueous Processing for Printed Organic Electronics: Conjugated Polymers with Multistage Cleavable Side Chains.

PubMed

Schmatz, Brian; Yuan, Zhibo; Lang, Augustus W; Hernandez, Jeff L; Reichmanis, Elsa; Reynolds, John R

2017-09-27

The ability to process conjugated polymers via aqueous solution is highly advantageous for reducing the costs and environmental hazards of large scale roll-to-roll processing of organic electronics. However, maintaining competitive electronic properties while achieving aqueous solubility is difficult for several reasons: (1) Materials with polar functional groups that provide aqueous solubility can be difficult to purify and characterize, (2) many traditional coupling and polymerization reactions cannot be performed in aqueous solution, and (3) ionic groups, though useful for obtaining aqueous solubility, can lead to a loss of solid-state order, as well as a screening of any applied bias. As an alternative, we report a multistage cleavable side chain method that combines desirable aqueous processing attributes without sacrificing semiconducting capabilities. Through the attachment of cleavable side chains, conjugated polymers have for the first time been synthesized, characterized, and purified in organic solvents, converted to a water-soluble form for aqueous processing, and brought through a final treatment to cleave the polymer side chains and leave behind the desired electronic material as a solvent-resistant film. Specifically, we demonstrate an organic soluble polythiophene that is converted to an aqueous soluble polyelectrolyte via hydrolysis. After blade coating from an aqueous solution, UV irradiation is used to cleave the polymer's side chains, resulting in a solvent-resistant, electroactive polymer thin film. In application, this process results in aqueous printed materials with utility for solid-state charge transport in organic field effect transistors (OFETs), along with red to colorless electrochromism in ionic media for color changing displays, demonstrating its potential as a universal method for aqueous printing in organic electronics.

Radiation effect of neutrons produced by D-D side reactions on a D-3He fusion reactor

NASA Astrophysics Data System (ADS)

Bahmani, J.

2017-04-01

One of the most important characteristics in D-3He fusion reactors is neutron production via D-D side reactions. The neutrons can activate structural material, degrading them and ultimately converting them into high-level radioactive waste, while it is really costly and difficult to remove them. The neutrons from a fusion reactor could also be used to make weapons-grade nuclear material, rendering such types of fusion reactors a serious proliferation hazard. A related problem is the presence of radioactive elements such as tritium in D-3He plasma, either as fuel for or as products of the nuclear reactions; substantial quantities of radioactive elements would not only pose a general health risk, but tritium in particular would also be another proliferation hazard. The problems of neutron radiation and radioactive element production are especially interconnected because both would result from the D-D side reaction. Therefore, the presentation approach for reducing neutrons via D-D nuclear side reactions in a D-3He fusion reactor is very important. For doing this research, energy losses and neutron power fraction in D-3He fusion reactors are investigated. Calculations show neutrons produced by the D-D nuclear side reaction could be reduced by changing to a more 3He-rich fuel mixture, but then the bremsstrahlung power loss fraction would increase in the D-3He fusion reactor.

Method for producing an atomic oxygen beam

NASA Technical Reports Server (NTRS)

Outlaw, Ronald A. (Inventor)

1989-01-01

A method for producing an atomic oxygen beam is provided by the present invention. First, a material 10' is provided which dissociates molecular oxygen and dissolves atomic oxygen into its bulk. Next, molecular oxygen is exposed to entrance surface 11' of material 10'. Next, material 10' is heated by heater 17' to facilitate the permeation of atomic oxygen through material 10' to the UHV side 12'. UHV side 12' is interfaced with an ultra-high vacuum (UHV) environment provided by UHV pump 15'. The atomic oxygen on the UHV side 12' is excited to a non-binding state by exciter 14' thus producing the release of atomic oxygen to form an atomic oxygen beam 35'.

Dependence of cell adhesion on extracellular matrix materials formed on pore bridge boundaries by nanopore opening and closing geometry.

PubMed

Kim, Sueon; Han, Dong Yeol; Chen, Zhenzhong; Lee, Won Gu

2018-04-30

In this study, we report experimental results for characterization of the growth and formation of pore bridge materials that modified the adhesion structures of cells cultured on nanomembranes with opening and closing geometry. To perform the proof-of-concept experiments, we fabricated two types of anodized alumina oxide substrates with single-sided opening (i.e., one side open, but closed at the other side) and double-sided opening (i.e., both sides open). In our experiment, we compared the densities of pores formed and of bridge materials which differently act as connective proteins depending on the size of pores. The results show that the pore opening geometry can be used to promote the net contact force between pores, resulting in the growth and formation of pore bridge materials before and after cell culture. The results also imply that the bridge materials can be used to attract the structural protrusion of filopodia that can promote the adhesion of cell-to-cell and cell-to-pore bridge. It is observed that the shape and size of cellular structures of filopodia depend on the presence of pore bridge materials. Overall, this observation brought us a significant clue that cells cultured on nanopore substrates would change the adhesion property depending on not only the formation of nanopores formed on the surface of topological substrates, but also that of pore bridge materials by its morphological growth.

Power inverters

DOEpatents

Miller, David H [Redondo Beach, CA; Korich, Mark D [Chino Hills, CA; Smith, Gregory S [Woodland Hills, CA

2011-11-15

Power inverters include a frame and a power module. The frame has a sidewall including an opening and defining a fluid passageway. The power module is coupled to the frame over the opening and includes a substrate, die, and an encasement. The substrate includes a first side, a second side, a center, an outer periphery, and an outer edge, and the first side of the substrate comprises a first outer layer including a metal material. The die are positioned in the substrate center and are coupled to the substrate first side. The encasement is molded over the outer periphery on the substrate first side, the substrate second side, and the substrate outer edge and around the die. The encasement, coupled to the substrate, forms a seal with the metal material. The second side of the substrate is positioned to directly contact a fluid flowing through the fluid passageway.

All-acrylic multigraft copolymers: Effect of side chain molecular weight and volume fraction on mechanical behavior

DOE PAGES

Goodwin, Andrew; Wang, Weiyu; Kang, Nam -Goo; ...

2015-08-21

We present in this paper the synthesis of poly(n-butyl acrylate)-g-poly(methyl methacrylate) (PnBA-g-PMMA) multigraft copolymers via a grafting-through (macromonomer) approach. The synthesis was performed using two controlled polymerization techniques. The PMMA macromonomer was obtained by high-vacuum anionic polymerization followed by the copolymerization of n-butyl acrylate and PMMA macromonomer using reversible addition–fragmentation chain transfer (RAFT) polymerization to yield the desired all-acrylic multigraft structures. The PnBA-g-PMMA multigraft structures exhibit randomly spaced branch points with various PMMA contents, ranging from 15 to 40 vol %, allowing an investigation into how physical properties vary with differences in the number of branch points and molecular weightmore » of grafted side chains. The determination of molecular weight and polydispersity indices of both the PMMA macromonomer and the graft copolymers was carried out using size exclusion chromatography with triple detection, and the structural characteristics of both the macromonomer and PnBA-g-PMMA graft materials were characterized by 1H and 13C NMR. Matrix-assisted laser desorption/ionization time-of-flight mass spectrometry was employed for monitoring the macromonomer synthesis. Thermal characteristics of the materials were analyzed using differential scanning calorimetry and thermogravimetric analysis. The mechanical performance of the graft materials was characterized by rheology and dynamic mechanical analysis, revealing that samples with PMMA content of 25–40 vol % exhibit superior elastomeric properties as compared to materials containing short PMMA side chains or <25 vol % PMMA. In conclusion, atomic force microscopy showed a varying degree of microphase separation between the glassy and rubbery components that is strongly dependent on PMMA side chain molecular weight.« less

Effect of Processing Parameters on Plastic Flow and Defect Formation in Friction-Stir-Welded Aluminum Alloy

NASA Astrophysics Data System (ADS)

Zeng, X. H.; Xue, P.; Wang, D.; Ni, D. R.; Xiao, B. L.; Ma, Z. Y.

2018-07-01

The effect of processing parameters on material flow and defect formation during friction stir welding (FSW) was investigated on 6.0-mm-thick 2014Al-T6 rolled plates with an artificially thickened oxide layer on the butt surface as the marker material. It was found that the "S" line in the stir zone (SZ) rotated with the pin and stayed on the retreating side (RS) and advancing side (AS) at low and high heat inputs, respectively. When the tool rotation rate was extremely low, the oxide layer under the pin moved to the RS first and then to the AS perpendicular to the welding direction, rather than rotating with the pin. The material flow was driven by the shear stresses produced by the forces at the pin-workpiece interface. With increases of the rotation rate, the depth of the shoulder-affected zone (SAZ) first decreased and then increased due to the decreasing shoulder friction force and increasing heat input. Insufficient material flow appeared in the whole of the SZ at low rotation rates and in the bottom of the SZ at high rotation rates, resulting in the formation of the "S" line. The extremely inadequate material flow is the reason for the lack of penetration and the kissing bonds in the bottom of the SZ at extremely low and low rotation rates, respectively.

Effect of Processing Parameters on Plastic Flow and Defect Formation in Friction-Stir-Welded Aluminum Alloy

NASA Astrophysics Data System (ADS)

Zeng, X. H.; Xue, P.; Wang, D.; Ni, D. R.; Xiao, B. L.; Ma, Z. Y.

2018-04-01

The effect of processing parameters on material flow and defect formation during friction stir welding (FSW) was investigated on 6.0-mm-thick 2014Al-T6 rolled plates with an artificially thickened oxide layer on the butt surface as the marker material. It was found that the "S" line in the stir zone (SZ) rotated with the pin and stayed on the retreating side (RS) and advancing side (AS) at low and high heat inputs, respectively. When the tool rotation rate was extremely low, the oxide layer under the pin moved to the RS first and then to the AS perpendicular to the welding direction, rather than rotating with the pin. The material flow was driven by the shear stresses produced by the forces at the pin-workpiece interface. With increases of the rotation rate, the depth of the shoulder-affected zone (SAZ) first decreased and then increased due to the decreasing shoulder friction force and increasing heat input. Insufficient material flow appeared in the whole of the SZ at low rotation rates and in the bottom of the SZ at high rotation rates, resulting in the formation of the "S" line. The extremely inadequate material flow is the reason for the lack of penetration and the kissing bonds in the bottom of the SZ at extremely low and low rotation rates, respectively.

Experimental investigation of solidification in metal foam enhanced phase change material

NASA Astrophysics Data System (ADS)

Beyne, W.; Bağci, O.; Huisseune, H.; Canière, H.; Danneels, J.; Daenens, D.; De Paepe, M.

2017-10-01

A major challenge for the use of phase change materials (PCMs) in thermal energy storage (TES) is overcoming the low thermal conductivity of PCM’s. The low conductivity gives rise to limited power during charging and discharging TES. Impregnating metal foam with PCM, however, has been found to enhance the heat transfer. On the other hand, the effect of foam parameters such as porosity, pore size and material type has remained unclear. In this paper, the effect of these foam parameters on the solidification time is investigated. Different samples of PCM-impregnated metal foam were experimentally tested and compared to one without metal foam. The samples varied with respect to choice of material, porosity and pore size. They were placed in a rectangular cavity and cooled from one side using a coolant flowing through a cold plate. The other sides of the rectangular cavity were Polymethyl Methacrylate (PM) walls exposed to ambient. The temperature on the exterior walls of the cavity was monitored as well as the coolant flow rate and its temperature. The metal foam inserts reduced the solidification times by at least 25 %. However, the difference between the best performing and worst performing metal foam is about 28 %. This shows a large potential for future research.

Anisotropic Nanomechanics of Boron Nitride Nanotubes: Nanostructured "Skin" Effect

NASA Technical Reports Server (NTRS)

Srivastava, Deepak; Menon, Madhu; Cho, KyeongJae

2000-01-01

The stiffness and plasticity of boron nitride nanotubes are investigated using generalized tight-binding molecular dynamics and ab-initio total energy methods. Due to boron-nitride BN bond buckling effects, compressed zigzag BN nanotubes are found to undergo novel anisotropic strain release followed by anisotropic plastic buckling. The strain is preferentially released towards N atoms in the rotated BN bonds. The tubes buckle anisotropically towards only one end when uniaxially compressed from both. A "skin-effect" model of smart nanocomposite materials is proposed which will localize the structural damage towards the 'skin' or surface side of the material.

Modelling of directional solidification of BSO

NASA Astrophysics Data System (ADS)

Lin, Chenting; Motakef, Shahryar

1993-03-01

A thermo-fluid model for vertical Bridgman growth of bismuth silicon oxide (BSO) as model material for semi-transparent, low thermal conductivity oxides is developed. Internal radiative heat transfer, together with convective and conductive heat transfer are considered in this model. Due to the strong internal thermal radiation within the grown crystal, the growth interface is highly convex into the melt, instead of being concave as is the case for opaque materials with the thermal conductivity of the melt larger than that of the solid. Reduction of the growth interface non-planarity through variations in the growth configuration is investigated. A furnace temperature profile consisting of a steep gradient on the melt side and shallow gradient on the solid side of the charge is found to be the most effective approach.

Biopolymers Containing Unnatural Amino Acids

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schultz, Peter

Although the main chain structure of polymers has a profound effect on their materials properties, the side groups can also have dramatic effects on their properties including conductivity, liquid crystallinity, hydrophobicity, elasticity and biodegradability. Unfortunately control over the side chain structure of polymers remains a challenge – it is difficult to control the sequence of chain elongation when mixtures of monomers are polymerized, and postpolymerization side chain modification is made difficult by polymer effects on side chain reactivity. In contrast, the mRNA templated synthesis of polypeptides on the ribosome affords absolute control over the primary sequence of the twenty aminomore » acid monomers. Moreover, the length of the biopolymer is precisely controlled as are sites of crosslinking. However, whereas synthetic polymers can be synthesized from monomers with a wide range of chemically defined structures, ribosomal biosynthesis is largely limited to the 20 canonical amino acids. For many applications in material sciences, additional building blocks would be desirable, for example, amino acids containing metallocene, photoactive, and halogenated side chains. To overcome this natural constraint we have developed a method that allows unnatural amino acids, beyond the common twenty, to be genetically encoded in response to nonsense or frameshift codons in bacteria, yeast and mammalian cells with high fidelity and good yields. Here we have developed methods that allow identical or distinct noncanonical amino acids to be incorporated at multiple sites in a polypeptide chain, potentially leading to a new class of templated biopolymers. We have also developed improved methods for genetically encoding unnatural amino acids. In addition, we have genetically encoded new amino acids with novel physical and chemical properties that allow selective modification of proteins with synthetic agents. Finally, we have evolved new metal-ion binding sites in proteins using a novel metal-ion binding amino acid, which may facilitate our ability to generate new protein based sensors and catalysts.« less

Biopolymers Containing Unnatural Building Blocks

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schultz, Peter G.

2013-06-30

Although the main chain structure of polymers has a profound effect on their materials properties, the side groups can also have dramatic effects on their properties including conductivity, liquid crystallinity, hydrophobicity, elasticity and biodegradability. Unfortunately control over the side chain structure of polymers remains a challenge – it is difficult to control the sequence of chain elongation when mixtures of monomers are polymerized, and postpolymerization side chain modification is made difficult by polymer effects on side chain reactivity. In contrast, the mRNA templated synthesis of polypeptides on the ribosome affords absolute control over the primary sequence of the twenty aminomore » acid monomers. Moreover, the length of the biopolymer is precisely controlled as are sites of crosslinking. However, whereas synthetic polymers can be synthesized from monomers with a wide range of chemically defined structures, ribosomal biosynthesis is largely limited to the 20 canonical amino acids. For many applications in material sciences, additional building blocks would be desirable, for example, amino acids containing metallocene, photoactive, and halogenated side chains. To overcome this natural constraint we have developed a method that allows unnatural amino acids, beyond the common twenty, to be genetically encoded in response to nonsense or frameshift codons in bacteria, yeast and mammalian cells with high fidelity and good yields. Here we have developed methods that allow identical or distinct noncanonical amino acids to be incorporated at multiple sites in a polypeptide chain, potentially leading to a new class of templated biopolymers. We have also developed improved methods for genetically encoding unnatural amino acids. In addition, we have genetically encoded new amino acids with novel physical and chemical properties that allow selective modification of proteins with synthetic agents. Finally, we have evolved new metal-ion binding sites in proteins using a novel metal-ion binding amino acid, which may facilitate our ability to generate new protein based sensors and catalysts.« less

Vehicle performance evaluation in side impact (MDB) using ES-II dummy

NASA Astrophysics Data System (ADS)

Ganessh, T. S.; Bansode, Praveen; Revankar, Vidyakant; Kumar, Sunil

2018-02-01

Side impact collision is one of the leading causes of death. Protection of people during lateral collision is challenging because of relatively small space available to restraint occupant compared to front. Hence, it is imperative to protect the occupants in side collision. It is a function of vehicle type and restraints for side protection. This paper focuses on evaluation of injury parameters of the ES II dummy during the lateral collision of different vehicles with different spaces, sections and materials. Thus the comparison will enable us to understand the sensitivity of space, B-pillar section and material which affects the injury parameters. This study will help automotive engineers to design side impact crashworthy vehicles.

Side effects of the strain-doping approach to develop optical materials based on Ge

NASA Astrophysics Data System (ADS)

Escalante, Jose M.

2018-05-01

Following the strain-doping approach for development of Ge based optical gain material, we have studied the impact of doping and strain on the optical properties of Germanium. Emphasizing the importance of the bandgap narrowing effect due to doping on the emission wavelength, we have computed a strain-doping-energy maps, which provide the strain and doping windows that can be considered in order to achieve a specific value of the Γ bandgap. Finally, we discuss the polarization of the emitted light, and its dependence on strains.

Flow Patterns During Friction Stir Welding

NASA Technical Reports Server (NTRS)

Guerra, M.; Schmidt, C.; McClure, J. C.; Murr, L. E.; Nunes, A. C.; Munafo, Paul M. (Technical Monitor)

2002-01-01

Friction Stir Welding is a relatively new technique for welding that uses a cylindrical pin or nib inserted along the weld seam. The nib (usually threaded) and the shoulder in which it is mounted are rapidly rotated and advanced along the seam. Extreme deformation takes place leaving a fine equiaxed structure in the weld region., The flow of metal during Friction Stir Welding is investigated using a faying surface tracer and a nib frozen in place during welding. It is shown that material is transported by two processes. The first is a wiping of material from the advancing front side of the nib onto a zone of material that rotates and advances with the nib. The material undergoes a helical motion within the rotational zone that both rotates and advances and descends in the wash of the threads on the nib and rises on the outer part of the rotational zone. After one or more rotations, this material is sloughed off in its wake of the nib, primarily on the advancing side. The second process is an entrainment of material from the front retreating side of the nib that fills in between the sloughed off pieces from the advancing side.

Magnetic confinement, Alfven wave reflection, and the origins of X-ray and mass-loss 'dividing lines' for late-type giants and supergiants

NASA Technical Reports Server (NTRS)

Rosner, R.; An, C.-H.; Musielak, Z. E.; Moore, R. L.; Suess, S. T.

1991-01-01

A simple qualitative model for the origin of the coronal and mass-loss dividing lines separating late-type giants and supergiants with and without hot, X-ray-emitting corona, and with and without significant mass loss is discussed. The basic physical effects considered are the necessity of magnetic confinement for hot coronal material on the surface of such stars and the large reflection efficiency for Alfven waves in cool exponential atmospheres. The model assumes that the magnetic field geometry of these stars changes across the observed 'dividing lines' from being mostly closed on the high effective temperature side to being mostly open on the low effective temperature side.

Promoting Improved Ballistic Resistance of Transparent Armor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wereszczak, Andrew A; Patel, P; Templeton, D W

2011-01-01

Transparent armor is a material or system of materials designed to be optically transparent, yet protect from fragmentation or ballistic impacts. Although engineered to defeat specific threats, or a range of threats, there are general requirements common to all of these designs. The primary requirement for a transparent armor system is to not only defeat the designated threat but also provide a multi-hit capability with minimized distortion of surrounding areas. Ground platforms have several parameters that must be optimized, such as weight, space efficiency, and cost versus performance. Glass exhibits tensile failure stress that is very much dependent on themore » amount of material being stressed, the side being tensile-stressed (i.e., air-versus tin-side if a float glass), and where it is being tensile stressed (i.e., in the middle or near an edge). An axiom arising from those effects is a greater amount of allowable deflection (i.e., higher failure stress) of a ballistically impacted transparent armor will result in improved ballistic resistance. Therefore, the interpretation and management of those tensile-failure-stress dependencies shall ultimately improve ballistic resistance and its predictability of transparent armor. Each of those three dependencies (size, side, and location) in a soda-lime silicate glass is described.« less

The structural response of a rail accelerator

NASA Technical Reports Server (NTRS)

Wang, S. Y.

1983-01-01

The transient response of a 0.4 by 0.6 cm rectangular bore rail accelerator was analyzed by a three dimensional finite element code. The copper rail deflected to a peak value of 0.08 mm in compression and then oscillated at an amplitude of 0.02 mm. Simultaneously the insulating side wall of glass fabric base, epoxy resin laminate (G-1o) was compressed to a peak value of 0.13 mm and rebounded to a steady state in extension. Projectile pinch or blowby due to the rail extension or compression, respectively, can be identified by examining the time history of the rail displacement. The effect of blowby was most significant at the side wall characterized by mm size displacement in compression. Dynamic stress calculations indicate that the G-10 supporting material behind the rail is subjected to over 21 MPa at which the G-10 could fail if the laminate was not carefully oriented. Results for a polycarbonate resin (Lexan) side wall show much larger displacements and stresses than for G-10. The tradeoff between the transparency of Lexan and the mechanical strength of G-10 for sidewall material is obvious. Displacement calculations from the modal method are smaller than the results from the direct integration method by almost an order of magnitude, because the high frequency effect is neglected.

The piecewise parabolic method for Riemann problems in nonlinear elasticity.

PubMed

Zhang, Wei; Wang, Tao; Bai, Jing-Song; Li, Ping; Wan, Zhen-Hua; Sun, De-Jun

2017-10-18

We present the application of Harten-Lax-van Leer (HLL)-type solvers on Riemann problems in nonlinear elasticity which undergoes high-load conditions. In particular, the HLLD ("D" denotes Discontinuities) Riemann solver is proved to have better robustness and efficiency for resolving complex nonlinear wave structures compared with the HLL and HLLC ("C" denotes Contact) solvers, especially in the shock-tube problem including more than five waves. Also, Godunov finite volume scheme is extended to higher order of accuracy by means of piecewise parabolic method (PPM), which could be used with HLL-type solvers and employed to construct the fluxes. Moreover, in the case of multi material components, level set algorithm is applied to track the interface between different materials, while the interaction of interfaces is realized through HLLD Riemann solver combined with modified ghost method. As seen from the results of both the solid/solid "stick" problem with the same material at the two sides of contact interface and the solid/solid "slip" problem with different materials at the two sides, this scheme composed of HLLD solver, PPM and level set algorithm can capture the material interface effectively and suppress spurious oscillations therein significantly.

TOPICAL REVIEW: First principles studies of multiferroic materials

NASA Astrophysics Data System (ADS)

Picozzi, Silvia; Ederer, Claude

2009-07-01

Multiferroics, materials where spontaneous long-range magnetic and dipolar orders coexist, represent an attractive class of compounds, which combine rich and fascinating fundamental physics with a technologically appealing potential for applications in the general area of spintronics. Ab initio calculations have significantly contributed to recent progress in this area, by elucidating different mechanisms for multiferroicity and providing essential information on various compounds where these effects are manifestly at play. In particular, here we present examples of density-functional theory investigations for two main classes of materials: (a) multiferroics where ferroelectricity is driven by hybridization or purely structural effects, with BiFeO3 as the prototype material, and (b) multiferroics where ferroelectricity is driven by correlation effects and is strongly linked to electronic degrees of freedom such as spin-, charge-, or orbital-ordering, with rare-earth manganites as prototypes. As for the first class of multiferroics, first principles calculations are shown to provide an accurate qualitative and quantitative description of the physics in BiFeO3, ranging from the prediction of large ferroelectric polarization and weak ferromagnetism, over the effect of epitaxial strain, to the identification of possible scenarios for coupling between ferroelectric and magnetic order. For the second class of multiferroics, ab initio calculations have shown that, in those cases where spin-ordering breaks inversion symmetry (e.g. in antiferromagnetic E-type HoMnO3), the magnetically induced ferroelectric polarization can be as large as a few µC cm-2. The examples presented point the way to several possible avenues for future research: on the technological side, first principles simulations can contribute to a rational materials design, aimed at identifying spintronic materials that exhibit ferromagnetism and ferroelectricity at or above room temperature. On the fundamental side, ab initio approaches can be used to explore new mechanisms for ferroelectricity by exploiting electronic correlations that are at play in transition metal oxides, and by suggesting ways to maximize the strength of these effects as well as the corresponding ordering temperatures.

Analysis of effective thermal conductivity of fibrous materials

NASA Technical Reports Server (NTRS)

Futschik, Michael W.; Witte, Larry C.

1993-01-01

The objective of this research is to gain a better understanding of the various mechanisms of heat transfer through fibrous materials and to gain insight into how fill-gas pressure influences the effective thermal conductivity. By way of first principles and some empiricism, two mathematical models are constructed to correlate experimental data. The data are obtained from a test series measuring the effective thermal conductivity of Nomex using a two-sided guarded hot-plate heater apparatus. Tests are conducted for certain mean temperatures and fill-gases over a range of pressures varying from vacuum to atmospheric conditions. The models are then evaluated to determine their effectiveness in representing the effective thermal conductivity of a fibrous material. The models presented herein predict the effective thermal conductivity of Nomex extremely well. Since the influence of gas conduction is determined to be the most influential component in predicting the effective thermal conductivity of a fibrous material, an improved representation of gas conduction is developed. Finally, some recommendations for extension to other random-oriented fiber materials are made concerning the usefulness of each model depending on their advantages and disadvantages.

Strain-induced vertical self-organization of semiconductor quantum dots: A computational study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shtinkov, N., E-mail: nshtinkov@uottawa.ca

Atomistic strain simulations based on the valence force field method are employed to study the vertical arrangements of semiconductor quantum dot (QD) multilayers. The effects of the QD shape, dimensions, and materials parameters are systematically investigated, varying independently the following parameters: spacer width H, QD lateral spacing D, base b, and height h, slope of the side facets, elastic properties of the dot and the substrate materials, and lattice mismatch between the dot and the substrate. The transition between vertically aligned and anti-aligned structures is found to be determined mainly by the ratios H/D and b/D, as well as bymore » the strain anisotropy of the substrate and to a lesser extent of the QD. The dependence on the QD height h is significant only for steep side facets and large aspect ratios h/b, and the effects of the lattice mismatch strain and the bulk elastic moduli are found to be negligible. The comparison with experimental data shows an excellent agreement with the results from the simulations, demonstrating that the presented analysis results in precise theoretical predictions for the vertical self-organization regime in a wide range of QD materials systems.« less

Triboelectric generator

DOEpatents

Wang, Zhong L; Fan, Fengru; Lin, Long; Zhu, Guang; Pan, Caofeng; Zhou, Yusheng

2015-11-03

A generator includes a thin first contact charging layer and a thin second contact charging layer. The thin first contact charging layer includes a first material that has a first rating on a triboelectric series. The thin first contact charging layer has a first side with a first conductive electrode applied thereto and an opposite second side. The thin second contact charging layer includes a second material that has a second rating on a triboelectric series that is more negative than the first rating. The thin first contact charging layer has a first side with a first conductive electrode applied thereto and an opposite second side. The thin second contact charging layer is disposed adjacent to the first contact charging layer so that the second side of the second contact charging layer is in contact with the second side of the first contact charging layer.

Effect of Pin Tool Shape on Metal Flow During Friction Stir Welding

NASA Technical Reports Server (NTRS)

McClure, J. C.; Coronado, E.; Aloor, S.; Nowak, B.; Murr, L. M.; Nunes, Arthur C., Jr.; Munafo, Paul M. (Technical Monitor)

2002-01-01

It has been shown that metal moves behind the rotating Friction Stir Pin Tool in two separate currents or streams. One current, mostly on the advancing side, enters a zone of material that rotates with the pin tool for one or more revolutions and eventually is abandoned behind the pin tool in crescent-shaped pieces. The other current, largely on the retreating side of the pin tool is moved by a wiping process to the back of the pin tool and fills in between the pieces of the rotational zone that have been shed by the rotational zone. This process was studied by using a faying surface copper trace to clarify the metal flow. Welds were made with pin tools having various thread pitches. Decreasing the thread pitch causes the large scale top-to-bottorn flow to break up into multiple vortices along the pin and an unthreaded pin tool provides insufficient vertical motion for there to be a stable rotational zone and flow of material via the rotational zone is not possible leading to porosity on the advancing side of the weld.

Compliant Electrode and Composite Material for Piezoelectric Wind and Mechanical Energy Conversions

NASA Technical Reports Server (NTRS)

Chen, Bin (Inventor)

2015-01-01

A thin film device for harvesting energy from wind. The thin film device includes one or more layers of a compliant piezoelectric material formed from a composite of a polymer and an inorganic material, such as a ceramic. Electrodes are disposed on a first side and a second side of the piezoelectric material. The electrodes are formed from a compliant material, such as carbon nanotubes or graphene. The thin film device exhibits improved resistance to structural fatigue upon application of large strains and repeated cyclic loadings.

Water Quality Performance of Three Side-by-Side Permeable Pavement Surface Materials: Three Year Update

EPA Science Inventory

Communities are increasingly installing structural low impact development (LID) practices to mange stormwater and reduce pollutant loads associated with stormwater runoff. Permeable pavement is a LID practice that has limited research on working-scale, side-by-side performance o...

Research in biomechanics of occupant protection.

PubMed

King, A I; Yang, K H

1995-04-01

This paper discusses the biomechanical bases for occupant protection against frontal and side impact. Newton's Laws of Motion are used to illustrate the effect of a crash on restrained and unrestrained occupants, and the concept of ride down is discussed. Occupant protection through the use of energy absorbing materials is described, and the mechanism of injury of some of the more common injuries is explained. The role of the three-point belt and the airbag in frontal protection is discussed along with the potential injuries that can result from the use of these restraint systems. Side impact protection is more difficult to attain but some protection can be derived from the use of padding or a side impact airbag. It is concluded that the front seat occupants are adequately protected against frontal impact if belts are worn in an airbag equipped vehicle. Side impact protection may not be uniform in all vehicles.

Shallow geologic structure of Lake Lacawac, Wayne Co. PA

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rohrer, J.W.; Meltzer, A.

1993-03-01

In this study the authors used seismic refraction techniques to characterize the shallow geologic structure around Lake Lacawac in northeastern Pennsylvania. They acquired six high resolution seismic refraction profiles, two each, on the east, west, and north sides of the lake. The lines were oriented perpendicular to each other to constrain dip of interfaces. The authors spaced receivers at 15 ft intervals with a maximum offset of 720 ft. A 12 lb. sledge hammer impacting a steel plate served as a seismic source on the east and west sides of the lake. The north side of the lake is amore » swamp. In the swamp they used a Betsy Seis-gun with 12 gauge shotgun shells as a seismic source, and marsh geophones as receivers. Source locations were 90 feet apart yielding 9 shot gathers per profile. Data was downloaded to a workstation for processing. Each shot record was scaled and bandpass filtered. First arrivals were defined and velocity-depth structure determined. The eastern side of the lake has a 15 ft layer of low velocity, (3,000 ft/s) material underlain by a layer of higher velocity, 7,500 ft/s material. The authors interpret this as a layer of shale below till. On the western side, a 15 ft layer of slow velocity, (3,500 ft/s) material is underlain by high velocity, 12,500 ft/s material. They interpret this as a layer of sandstone beneath till. On the north side of the lake, the surface layer is saturated organic material with an average velocity of 2,550 ft/s. This layer varies in thickness from 0--20 ft. The organic material is underlain by higher velocity material ([approximately]15,000 ft/s) interpreted as sandstone. To the southwest, the sandstone unit disappears across an abrupt, nearly vertical boundary. Minimum vertical offset across this NE/SW striking feature is 114 ft. Forward modeling is being done to help constrain subsurface structure.« less

Insulating Material Requirements for Low-Power-Consumption Electrowetting-Based Liquid Lenses.

PubMed

Chevalliot, Stéphanie; Malet, Géraldine; Keppner, Herbert; Berge, Bruno

2016-12-27

Insulating materials from the parylene family were investigated for use in low-power-consumption electrowetting-based liquid lenses. It was shown that for DC-driven operations, parylene C leads to hysteresis, regardless of the presence of a hydrophobic top coat. This hysteresis was attributed to the non-negligible time needed to reach a stable contact angle, due to charge injection and finite conductivity of the material. It was further demonstrated that by using materials with better insulating properties, such as parylene HT and VT4, satisfactory results can be obtained under DC voltages, reaching a low contact angle hysteresis of below 0.2°. We propose a simplified model that takes into account the injection of charges from both sides of the insulating material (the liquid side and the electrode side), showing that electrowetting response can be both increased and decreased.

Research on electrodischarge drilling of polycrystalline diamond with increased gap voltage

NASA Astrophysics Data System (ADS)

Skoczypiec, Sebastian; Bizoń, Wojciech; Żyra, Agnieszka

2018-05-01

This paper presents an experimental investigation of the machining characteristics of polycrystalline diamond (PCD). Machining of PCD by conventional technologies is not an effective solution. Due to presence of cobalt this material can be machined by application of electrical discharges. On the other side, electrical conductivity of PCD is on the limit of electrodischarge machining (EDM) possibilities. Proposed paper reports experimental investigation on electrodischarge drilling of PCD samples. The test were carried out with application on of high-voltage (up to 550 V) pulse power unit for two kinds of dielectrics: carbon based (Exxsol D80) and de-ionized water. As output parameters machining accuracy (side gap), material removal rate were selected. Also, based on SEM photographs and energy dispersive X-ray spectroscopy (EDS) analysis, a qualitative evaluation of the obtained results was presented.

Facile preparation of magnetic graphene double-sided mesoporous composites for the selective enrichment and analysis of endogenous peptides.

PubMed

Yin, Peng; Sun, Nianrong; Deng, Chunhui; Li, Yan; Zhang, Xiangmin; Yang, Pengyuan

2013-08-01

In this work, magnetic graphene double-sided mesoporous nanocomposites (mag-graphene@mSiO₂) were synthesized by coating a layer of mesoporous silica materials on each side of magnetic grapheme. The surfactant (CTAB) mediated sol-gel coating was performed using tetraethyl orthosilicate as the silica source. The as-made magnetic graphene double-sided mesoporous silica composites were treated with high-temperature calcination to remove the hydroxyl on the surface. The novel double-sided materials possess high surface area (167.8 cm²/g) and large pore volume (0.2 cm³/g). The highly open pore structure presents uniform pore size (3.2 nm) and structural stability. The hydrophobic interior pore walls could ensure an efficient adsorption of target molecules through hydrophobic-hydrophobic interaction. At the same time, the magnetic Fe₃O₄ particles on both sides of the materials could simplify the process of enrichment, which plays an important role in the treatment of complex biological samples. The magnetic graphene double-sided nanocomposites were successfully applied to size-selective and specific enrichment of peptides in standard peptide mixtures, protein digest solutions, and human urine samples. Finally, the novel material was applied to selective enrichment of endogenous peptides in mouse brain tissue. The enriched endogenous peptides were then analyzed by LC-MS/MS, and 409 endogenous peptides were detected and identified. The results demonstrate that the as-made mag-graphene@mSiO₂ have powerful potential for peptidome research. © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

U.S. Biodefense & Homeland Security: Toward Detection & Attribution

DTIC Science & Technology

2006-12-01

Agency (EPA) and FBI hazardous material teams worked side-by-side, searching 280 barrels containing 635 bags of quarantined mail that had been...hazardous material teams searched 280 barrels containing 635 bags of quarantined mail that had been seized as evidence. The final letter was addressed to...Chapter IV. He provided important research material and fresh ideas based on his expertise as Scientist-in-Residence of the Center for

The effect of acute hypoxia on short-circuit current and epithelial resistivity in biopsies from human colon.

PubMed

Carra, Graciela E; Ibáñez, Jorge E; Saraví, Fernando D

2013-09-01

In isolated colonic mucosa, decreases in short-circuit current (ISC) and transepithelial resistivity (RTE) occur when hypoxia is either induced at both sides or only at the serosal side of the epithelium. We assessed in human colon biopsies the sensitivity to serosal-only hypoxia and mucosal-only hypoxia and whether Na, K-ATPase blockade with ouabain interacts with hypoxia. Biopsy material from patients undergoing colonoscopy was mounted in an Ussing chamber for small samples (1-mm2 window). In a series of experiments we assessed viability and the electrical response to the mucolytic, dithiothreitol (1 mmol/l). In a second series, we explored the effect of hypoxia without and with ouabain. In a third series, we evaluated the response to a cycle of hypoxia and reoxygenation induced at the serosal or mucosal side while keeping the oxygenation of the opposite side. 1st series: Dithiothreitol significantly decreased the unstirred layer and ISC but increased RTE. 2nd series: Both hypoxia and ouabain decreased ISC, but ouabain increased RTE and this effect on RTE prevailed even during hypoxia. 3rd series: Mucosal hypoxia caused lesser decreases of ISC and RTE than serosal hypoxia; in the former, but not in the latter, recovery was complete upon reoxygenation. In mucolytic concentration, dithiothreitol modifies ISC and RTE. Oxygen supply from the serosal side is more important to sustain ISC and RTE in biopsy samples. The different effect of hypoxia and Na, K-ATPase blockade on RTE suggests that their depressing effect on ISC involves different mechanisms.

Full-field Strain Methods for Investigating Failure Mechanisms in Triaxial Braided Composites

NASA Technical Reports Server (NTRS)

Littell, Justin D.; Binienda, Wieslaw K.; Goldberg, Robert K.; Roberts, Gary D.

2008-01-01

Composite materials made with triaxial braid architecture and large tow size carbon fibers are beginning to be used in many applications, including composite aircraft and engine structures. Recent advancements in braiding technology have led to commercially viable manufacturing approaches for making large structures with complex shape. Although the large unit cell size of these materials is an advantage for manufacturing efficiency, the fiber architecture presents some challenges for materials characterization, design, and analysis. In some cases, the static load capability of structures made using these materials has been higher than expected based on material strength properties measured using standard coupon tests. A potential problem with using standard tests methods for these materials is that the unit cell size can be an unacceptably large fraction of the specimen dimensions. More detailed investigation of deformation and failure processes in large unit cell size triaxial braid composites is needed to evaluate the applicability of standard test methods for these materials and to develop alternative testing approaches. In recent years, commercial equipment has become available that enables digital image correlation to be used on a more routine basis for investigation of full field 3D deformation in materials and structures. In this paper, some new techniques that have been developed to investigate local deformation and failure using digital image correlation techniques are presented. The methods were used to measure both local and global strains during standard straight-sided coupon tensile tests on composite materials made with 12 and 24 k yarns and a 0/+60/-60 triaxial braid architecture. Local deformation and failure within fiber bundles was observed, and this local failure had a significant effect on global stiffness and strength. The matrix material had a large effect on local damage initiation for the two matrix materials used in this investigation. Premature failure in regions of the unit cell near the edge of the straight-sided specimens was observed for transverse tensile tests in which the braid axial fibers were perpendicular to the specimen axis and the bias fibers terminated on the cut edges in the specimen gage section. This edge effect is one factor that could contribute to a measured strength that is lower than the actual material strength in a structure without edge effects.

Citizen's dosimeter

DOEpatents

Klemic, Gladys [Naperville, IL; Bailey, Paul [Chicago, IL; Breheny, Cecilia [Yonkers, NY

2008-09-02

The present invention relates to a citizen's dosimeter. More specifically, the invention relates to a small, portable, personal dosimetry device designed to be used in the wake of a event involving a Radiological Dispersal Device (RDD), Improvised Nuclear Device (IND), or other event resulting in the contamination of large area with radioactive material or where on site personal dosimetry is required. The card sized dosimeter generally comprises: a lower card layer, the lower card body having an inner and outer side; a upper card layer, the layer card having an inner and outer side; an optically stimulated luminescent material (OSLM), wherein the OSLM is sandwiched between the inner side of the lower card layer and the inner side of the upper card layer during dosimeter radiation recording, a shutter means for exposing at least one side of the OSLM for dosimeter readout; and an energy compensation filter attached to the outer sides of the lower and upper card layers.

Rotator side chains trigger cooperative transition for shape and function memory effect in organic semiconductors.

PubMed

Chung, Hyunjoong; Dudenko, Dmytro; Zhang, Fengjiao; D'Avino, Gabriele; Ruzié, Christian; Richard, Audrey; Schweicher, Guillaume; Cornil, Jérôme; Beljonne, David; Geerts, Yves; Diao, Ying

2018-01-18

Martensitic transition is a solid-state phase transition involving cooperative movement of atoms, mostly studied in metallurgy. The main characteristics are low transition barrier, ultrafast kinetics, and structural reversibility. They are rarely observed in molecular crystals, and hence the origin and mechanism are largely unexplored. Here we report the discovery of martensitic transition in single crystals of two different organic semiconductors. In situ microscopy, single-crystal X-ray diffraction, Raman and nuclear magnetic resonance spectroscopy, and molecular simulations combined indicate that the rotating bulky side chains trigger cooperative transition. Cooperativity enables shape memory effect in single crystals and function memory effect in thin film transistors. We establish a molecular design rule to trigger martensitic transition in organic semiconductors, showing promise for designing next-generation smart multifunctional materials.

Electrorheological effect and electro-optical properties of side-on liquid crystalline polysiloxane in a nematic solvent.

PubMed

Kaneko, Kosuke; Oto, Kodai; Kawai, Toshiaki; Choi, Hyunseok; Kikuchi, Hirotsugu; Nakamura, Naotake

2013-08-26

The electrorheological (ER) effect and the electro-optical properties of a ''side-on'' liquid crystalline polysiloxane (PS) are investigated. A large ER effect is observed and the response to the shear stress of neat PS in the nematic phase is shown to be affected by the shear rate. PS is also mixed with a low-molar nematic liquid crystal (5CB) in order to improve the response behavior to the applied electric field. The rheological properties of such mixtures are highly dependent on the concentration of 5CB. The composites respond faster to the applied electric field and have improved electro-optical properties. This study offers a new perspective on the development of liquid crystal materials for the ER effect. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Active magnetic regenerator method and apparatus

DOEpatents

DeGregoria, Anthony J.; Zimm, Carl B.; Janda, Dennis J.; Lubasz, Richard A.; Jastrab, Alexander G.; Johnson, Joseph W.; Ludeman, Evan M.

1993-01-01

In an active magnetic regenerator apparatus having a regenerator bed of material exhibiting the magnetocaloric effect, flow of heat transfer fluid through the bed is unbalanced, so that more fluid flows through the bed from the hot side of the bed to the cold side than from the cold side to the hot side. The excess heat transfer fluid is diverted back to the hot side of the bed. The diverted fluid may be passed through a heat exchanger to draw heat from a fluid to be cooled. The apparatus may be operated at cryogenic temperatures, and the heat transfer fluid may be helium gas and the fluid to be cooled may be hydrogen gas, which is liquified by the device. The apparatus can be formed in multiple stages to allow a greater span of cooling temperatures than a single stage, and each stage may be comprised of two bed parts. Where two bed parts are employed in each stage, a portion of the fluid passing from the hot side to the cold side of a first bed part which does not have a magnetic field applied thereto is diverted back to the cold side of the other bed part in the stage, where it is passed through to the hot side. The remainder of the fluid from the cold side of the bed part of the first stage is passed to the hot side of the bed part of the second stage.

System and method for measuring permeability of materials

DOEpatents

Hallman, Jr., Russell Louis; Renner, Michael John

2013-07-09

Systems and methods are provided for measuring the permeance of a material. The permeability of the material may also be derived. Systems typically provide a liquid or high concentration fluid bath on one side of a material test sample, and a gas flow across the opposing side of the material test sample. The mass flow rate of permeated fluid as a fraction of the combined mass flow rate of gas and permeated fluid is used to calculate the permeance of the material. The material test sample may be a sheet, a tube, or a solid shape. Operational test conditions may be varied, including concentration of the fluid, temperature of the fluid, strain profile of the material test sample, and differential pressure across the material test sample.

Material permeance measurement system and method

DOEpatents

Hallman, Jr., Russell Louis; Renner, Michael John [Oak Ridge, TN

2012-05-08

A system for measuring the permeance of a material. The permeability of the material may also be derived. The system provides a liquid or high concentration fluid bath on one side of a material test sample, and a gas flow across the opposing side of the material test sample. The mass flow rate of permeated fluid as a fraction of the combined mass flow rate of gas and permeated fluid is used to calculate the permeance of the material. The material test sample may be a sheet, a tube, or a solid shape. Operational test conditions may be varied, including concentration of the fluid, temperature of the fluid, strain profile of the material test sample, and differential pressure across the material test sample.

Large-scale lateral nanowire arrays nanogenerators

DOEpatents

Wang, Zhong L; Xu, Chen; Qin, Yong; Zhu, Guang; Yang, Rusen; Hu, Youfan; Zhang, Yan

2014-01-07

In a method of making a generating device, a plurality of spaced apart elongated seen members are deposited onto a surface of a flexible non-conductive substrate. An elongated conductive layer is applied to a top surface and a first side of each seed member, thereby leaving an exposed second side opposite the first side. A plurality of elongated piezoelectric nanostructures is grown laterally from the second side of each seed layer. A second conductive material is deposited onto the substrate adjacent each elongated first conductive layer so as to be soupled the distal end of each of the plurality of elongated piezoelectric nanostructures. The second conductive material is selected so as to form a Schottky barrier between the second conductive material and the distal end of each of the plurality of elongated piezoelectric nanostructures and so as to form an electrical contact with the first conductive layer.

This Side Up: Making Decisions About Drugs.

ERIC Educational Resources Information Center

Cook, Maureen H.; Newman, Carol

This guide was developed as a source of information for young people who are faced with making decisions about drugs. Written in a "catchy" yet informative style, the materials presented address the following areas of concern: (1) definitions and effects of various drugs, including alcohol, tobacco, and narcotics; (2) physical and psychological…

Locating interfaces in vertically-layered materials and determining concentrations in mixed materials utilizing acoustic impedance measurements

DOEpatents

Langlois, Gary N.

1983-09-13

Measurement of the relative and actual value of acoustic characteristic impedances of an unknown substance, location of the interfaces of vertically-layered materials, and the determination of the concentration of a first material mixed in a second material. A highly damped ultrasonic pulse is transmitted into one side of a reference plate, such as a tank wall, where the other side of the reference plate is in physical contact with the medium to be measured. The amplitude of a return signal, which is the reflection of the transmitted pulse from the interface between the other side of the reference plate and the medium, is measured. The amplitude value indicates the acoustic characteristic impedance of the substance relative to that of the reference plate or relative to that of other tested materials. Discontinuities in amplitude with repeated measurements for various heights indicate the location of interfaces in vertically-layered materials. Standardization techniques permit the relative acoustic characteristic impedance of a substance to be converted to an actual value. Calibration techniques for mixtures permit the amplitude to be converted to the concentration of a first material mixed in a second material.

Locating interfaces in vertically-layered materials and determining concentrations in mixed materials utilizing acoustic impedance measurements

DOEpatents

Langlois, G.N.

1983-09-13

Measurement of the relative and actual value of acoustic characteristic impedances of an unknown substance, location of the interfaces of vertically-layered materials, and the determination of the concentration of a first material mixed in a second material are disclosed. A highly damped ultrasonic pulse is transmitted into one side of a reference plate, such as a tank wall, where the other side of the reference plate is in physical contact with the medium to be measured. The amplitude of a return signal, which is the reflection of the transmitted pulse from the interface between the other side of the reference plate and the medium, is measured. The amplitude value indicates the acoustic characteristic impedance of the substance relative to that of the reference plate or relative to that of other tested materials. Discontinuities in amplitude with repeated measurements for various heights indicate the location of interfaces in vertically-layered materials. Standardization techniques permit the relative acoustic characteristic impedance of a substance to be converted to an actual value. Calibration techniques for mixtures permit the amplitude to be converted to the concentration of a first material mixed in a second material. 6 figs.

Nordic dentists' opinions on the safety of amalgam and other dental restorative materials.

PubMed

Widström, E; Haugejorden, O; Sundberg, H; Birn, H

1993-08-01

The safety of amalgam and other restorative materials has caused concern among dental patients in recent years. The aim of this study was to obtain information on dentists' perceived competence in handling different filling materials and their opinions on the safety of these. A random sample of practising dentists in Denmark, Finland, Norway, and Sweden received a mail questionnaire in spring 1990. Answers were received from 1732 dentists (65%). The study showed that the respondents believed that their theoretic knowledge and clinical skills were generally at a high level regarding restorative materials. The risks of the side-effects of gold, ceramic materials, and glass ionomer were considered to be low by about 90% of the respondents. Amalgam was considered to be significantly more hazardous by the Swedish respondents than the others. Interestingly, composite was considered to be associated with a high risk of side-effects by about half of the dentists in all Nordic countries. The dentists' opinions were not found to be greatly influenced by their sex, age, or place of residence but rather by their country and service sector. Against the background of the present lack of scientific evidence on the hazardousness of amalgam or other restorative materials for patients' general health, these findings indicate that dentists are influenced by discussions in the mass media about dental treatment and materials and, of course, by the guidelines given by the health authorities in their own countries. Few dentists were shown to be concerned about occupational risks associated with the use of amalgam, and they had not had their own amalgam fillings replaced.(ABSTRACT TRUNCATED AT 250 WORDS)

49 CFR 238.217 - Side structure.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 49 Transportation 4 2012-10-01 2012-10-01 false Side structure. 238.217 Section 238.217... Equipment § 238.217 Side structure. Each passenger car shall comply with the following: (a) Side posts and... of the material used to that of mild open-hearth steel for a car whose structural members are made of...

49 CFR 238.217 - Side structure.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 49 Transportation 4 2014-10-01 2014-10-01 false Side structure. 238.217 Section 238.217... Equipment § 238.217 Side structure. Each passenger car shall comply with the following: (a) Side posts and... of the material used to that of mild open-hearth steel for a car whose structural members are made of...

49 CFR 238.217 - Side structure.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 49 Transportation 4 2013-10-01 2013-10-01 false Side structure. 238.217 Section 238.217... Equipment § 238.217 Side structure. Each passenger car shall comply with the following: (a) Side posts and... of the material used to that of mild open-hearth steel for a car whose structural members are made of...

How We Used NASA Lunar Set in Planetary Material Science Analog Studies on Lunar Basalts and Breccias with Industrial Materials of Steels and Ceramics

NASA Technical Reports Server (NTRS)

Berczi, S.; Cech, V.; Jozsa, S.; Szakmany, G.; Fabriczy, A.; Foldi, T.; Varga, T.

2005-01-01

Analog studies play important role in space materials education. Various aspects of analogies are used in our courses. In this year two main rock types of NASA Lunar Set were used in analog studies in respect of processes and textures with selected industrial material samples. For breccias and basalts on the lunar side, ceramics and steels were found as analogs on the industrial side. Their processing steps were identified on the basis of their textures both in lunar and in industrial groups of materials.

Overall heat transfer coefficient and pressure drop in a typical tubular exchanger employing alumina nano-fluid as the tube side hot fluid

NASA Astrophysics Data System (ADS)

Kabeel, A. E.; Abdelgaied, Mohamed

2016-08-01

Nano-fluids are used to improve the heat transfer rates in heat exchangers, especially; the shell-and-tube heat exchanger that is considered one of the most important types of heat exchangers. In the present study, an experimental loop is constructed to study the thermal characteristics of the shell-and-tube heat exchanger; at different concentrations of Al2O3 nonmetallic particles (0.0, 2, 4, and 6 %). This material concentrations is by volume concentrations in pure water as a base fluid. The effects of nano-fluid concentrations on the performance of shell and tube heat exchanger have been conducted based on the overall heat transfer coefficient, the friction factor, the pressure drop in tube side, and the entropy generation rate. The experimental results show that; the highest heat transfer coefficient is obtained at a nano-fluid concentration of 4 % of the shell side. In shell side the maximum percentage increase in the overall heat transfer coefficient has reached 29.8 % for a nano-fluid concentration of 4 %, relative to the case of the base fluid (water) at the same tube side Reynolds number. However; in the tube side the maximum relative increase in pressure drop has recorded the values of 12, 28 and 48 % for a nano-material concentration of 2, 4 and 6 %, respectively, relative to the case without nano-fluid, at an approximate value of 56,000 for Reynolds number. The entropy generation reduces with increasing the nonmetallic particle volume fraction of the same flow rates. For increase the nonmetallic particle volume fraction from 0.0 to 6 % the rate of entropy generation decrease by 10 %.

A Study on the Impact of Poly(3-hexylthiophene) Chain Length and Other Applied Side-Chains on the NO2 Sensing Properties of Conducting Graft Copolymers

PubMed Central

Kepska, Kinga

2018-01-01

The detection and concentration measurements of low concentrations of nitrogen dioxide (NO2) are important because of its negative effects on human health and its application in many fields of industry and safety systems. In our approach, conducting graft copolymers based on the poly(3-hexylthiophene) (P3HT) conducting polymer and other side-chains, polyethylene glycol (PEG) and dodec-1-en, grafted on a poly(methylhydrosiloxane) backbone, were investigated. The grafts containing PEG (PEGSil) and dodec-1-en (DodecSil) in two variants, namely, fractions with shorter (hexane fraction -H) and longer (chloroform fraction -CH) side-chains of P3HT, were tested as receptor structures in NO2 gas sensors. Their responses to NO2, within the concentration range of 1–20 ppm, were investigated in an nitrogen atmosphere at different operating temperatures—room temperature (RT) = 25 °C, 50 °C, and 100 °C. The results indicated that both of the copolymers with PEG side-chains had higher responses to NO2 than the materials with dodec-1-en side-chains. Furthermore, the results indicated that, in both cases, H fractions were more sensitive than CH fractions. The highest response to 1 ppm of NO2, from the investigated graft copolymers, had PEGSil H, which indicated a response of 1330% at RT and 1980% at 100 °C. The calculated lower-limit of the detection of this material is lower than 300 ppb of NO2 at 100 °C. This research indicated that graft copolymers of P3HT had great potential for low temperature NO2 sensing, and that the proper choice of other side-chains in graft copolymers can improve their gas sensing properties. PMID:29558448

Mixed Conducting Electrodes for Better AMTEC Cells

NASA Technical Reports Server (NTRS)

Ryan, Margaret; Williams, Roger; Homer, Margie; Lara. Liana

2003-01-01

Electrode materials that exhibit mixed conductivity (that is, both electronic and ionic conductivity) have been investigated in a continuing effort to improve the performance of the alkali metal thermal-to-electric converter (AMTEC). These electrode materials are intended primarily for use on the cathode side of the sodium-ion-conducting solid electrolyte of a sodium-based AMTEC cell. They may also prove useful in sodium-sulfur batteries, which are under study for use in electric vehicles. An understanding of the roles played by the two types of conduction in the cathode of a sodium-based AMTEC cell is prerequisite to understanding the advantages afforded by these materials. In a sodium-based AMTEC cell, the anode face of an anode/solid-electrolyte/cathode sandwich is exposed to Na vapor at a suitable pressure. Upon making contact with the solid electrolyte on the anode side, Na atoms oxidize to form Na+ ions and electrons. Na+ ions then travel through the electrolyte to the cathode. Na+ ions leave the electrolyte at the cathode/electrolyte interface and are reduced by electrons that have been conducted through an external electrical load from the anode to the cathode. Once the Na+ ions have been reduced to Na atoms, they travel through the cathode to vaporize into a volume where the Na vapor pressure is much lower than it is on the anode side. Thus, the cathode design is subject to competing requirements to be thin enough to allow transport of sodium to the low-pressure side, yet thick enough to afford adequate electronic conductivity. The concept underlying the development of the present mixed conducting electrode materials is the following: The constraint on the thickness of the cathode can be eased by incorporating Na+ -ionconducting material to facilitate transport of sodium through the cathode in ionic form. At the same time, by virtue of the electronically conducting material mixed with the ionically conducting material, reduction of Na+ ions to Na atoms can take place throughout the thickness of the cathode. The net effect is to reduce the diffusion and flow resistance to sodium through the electrode while reducing the electronic resistance by providing shorter conduction paths for electrons. Reduced resistance to both sodium transport and electronic conductivity results in an increase in electric power output.

Standard Methods for Unnotched Tension Testing of Textile Composites

NASA Technical Reports Server (NTRS)

Portanova, M. A.

1995-01-01

An investigation was conducted by researchers at the Boeing Defense & Space Group to investigate the effects of specimen sizing on several braided textile materials. Test results from this and other test programs were compared in an effort to determine what effect, if any, specimen size has on elastic property measurements of unnotched tension test. In general, the unnotched tensile strength of 2-D braids was found to be insensitive to specimen width, length, or thickness effects. The results from this study suggest that standard testing methods used for tape materials may be sufficient for tension testing of textile composite materials. Specifically, the straight sided specimen geometry described in ASTM 3034, and used by Boeing, should provide acceptable results. Further experiments performed at Boeing and by other investigators on other textile architectures suggest similar results. Although specimen size studies were not conducted, failing stresses varied on the same order as those obtained with the 2-D materials. This suggests that the accuracy of the results were consistent with those obtained with the 2-D materials.

Fluid permeability measurement system and method

DOEpatents

Hallman, Jr., Russell Louis; Renner, Michael John [Oak Ridge, TN

2008-02-05

A system for measuring the permeance of a material. The permeability of the material may also be derived. The system provides a liquid or high concentration fluid bath on one side of a material test sample, and a gas flow across the opposing side of the material test sample. The mass flow rate of permeated fluid as a fraction of the combined mass flow rate of gas and permeated fluid is used to calculate the permeance of the material. The material test sample may be a sheet, a tube, or a solid shape. Operational test conditions may be varied, including concentration of the fluid, temperature of the fluid, strain profile of the material test sample, and differential pressure across the material test sample.

Method of coextruding plastics to form a composite sheet

DOEpatents

Tsien, Hsue C.

1985-06-04

This invention pertains to a method of producing a composite sheet of plastic materials by means of coextrusion. Two plastic materials are matched with respect to their melt indices. These matched plastic materials are then coextruded in a side-by-side orientation while hot and soft to form a composite sheet having a substantially uniform demarkation therebetween. The plastic materials are fed at a substantially equal extrusion velocity and generally have substantially equal viscosities. The coextruded plastics can be worked after coextrusion while they are still hot and soft.

An "intelligent" approach based on side-by-side cascade-correlation neural networks for estimating thermophysical properties from photothermal responses

NASA Astrophysics Data System (ADS)

Grieu, Stéphane; Faugeroux, Olivier; Traoré, Adama; Claudet, Bernard; Bodnar, Jean-Luc

2015-01-01

In the present paper, an artificial-intelligence-based approach dealing with the estimation of thermophysical properties is designed and evaluated. This new and "intelligent" approach makes use of photothermal responses obtained when subjecting materials to a light flux. So, the main objective of the present work was to estimate simultaneously both the thermal diffusivity and conductivity of materials, from front-face or rear-face photothermal responses to pseudo random binary signals. To this end, we used side-by-side feedforward neural networks trained with the cascade-correlation algorithm. In addition, computation time was a key point to consider. That is why the developed algorithms are computationally tractable.

Boat Hull Blisters: Repair Techniques and Long Term Effects on Hull Degradation

DTIC Science & Technology

1988-08-01

Swelling Stresses Produced by Diffusion; Long Term Damage by Water Absorption ; Effects of Gel Coat on Leaching of Water Soluble Material from...leinforcesents 5. Swelling Stresses Produced by Diffusion 6. Long Term Damage by Water Absorption 7. Effects of Gel Coat on Leaching of Water Soluble...the importance of bilge side water pick-up is emphasized. A second method for preventing blister formation is to eliminate or minimize the water soluble

Effect of side-chain structure of rigid polyimide dispersant on mechanical properties of single-walled carbon nanotube/cyanate ester composite.

PubMed

Yuan, Wei; Li, Weifeng; Mu, Yuguang; Chan-Park, Mary B

2011-05-01

Three kinds of polymer, polyimide without side-chain (PI), polyimide-graft-glyceryl 4-nonylphenyl ether (PI-GNE), and polyimide-graft-bisphenol A diglyceryl acrylate (PI-BDA), have been synthesized and used to disperse single-walled carbon nanotubes (SWNTs) and to improve the interfacial bonding between SWNTs and cyanate ester (CE) matrix. Visual observation, UV-vis-near-IR (UV-vis-NIR) spectra, and atomic force microscopy (AFM) images show that both PI-GNE and PI-BDA are highly effective at dispersing and debundling SWNTs in DMF, whereas PI is less effective. Interaction between SWNTs and PI, PI-GNE or PI-BDA was confirmed by computer simulation and Raman spectra. A series of CE-based composite films reinforced with different loadings of SWNTs, SWNTs/PI, SWNTs/PI-GNE and SWNTs/PI-BDA were prepared by solution casting. It was found that, because of the unique side-chain structure of PI-BDA, SWNTs/PI-BDA disperse better in CE matrix than do SWNTs/PI-GNE, SWNTs/PI, and SWNTs. As a result, SWNTs/PI-BDA/CE composites have the greatest improvement in mechanical properties of the materials tested. These results imply that the choice of side-chain on a dispersant is very important to the dispersion of SWNTs in matrix and the filler/matrix interfacial adhesion, which are two key requirements for achieving effective reinforcement.

Exploring Motivations, Awareness of Side Effects, and Attitudes among Potential Egg Donors

PubMed Central

Gezinski, Lindsay B.; Karandikar, Sharvari; Carter, James; White, Melinda

2016-01-01

This research study surveyed prospective egg donors at orientation to (a) understand women’s motivations to donate eggs, (b) assess awareness and knowledge of egg donation prior to entry into the egg donation program, and (c) explore attitudes toward egg donation. Ninety-two women completed the questionnaire at one fertility clinic located in the Midwest between August 2011 and August 2012. Descriptive and inferential statistics as well as textual analysis were used to analyze the data. Three themes emerged regarding participant motivations: (1) altruistic, (2) financial, and (3) desire to pass on genetic material. The majority of participants were unconcerned with potential physical and psychological side effects; however, differences emerged based on motherhood status and educational level. Although potential donors felt recipients should receive some information about the donor, they tended to value privacy regarding information giving to resultant offspring. This research study has implications for social work practice, policy, and future research. It is crucial that women receive adequate procedural and side effect information prior to engaging in egg donation. PMID:27263197

Bacteriological evaluation for one-and two-piece implant design supporting mandibular overdenture

PubMed Central

Abdelwahed, Ahmed; Mahrous, Ahmed I.; Abadallah, Mohamed Farouk; Asfour, Hani; Aldawash, Hussien A.; Alagha, Ebaa I.

2015-01-01

Background: This study evaluated and compared the bacteriological effect of two-piece implants and one-piece implants in complete overdenture cases on supporting structures. Materials and Methods: Ten male completely edentulous patients were selected and randomly divided into two equal groups according to the implant design and surgical technique for this study; Group 1: Patients were rehabilitated with complete mandibular overdenture supported by two-piece implants one on each side of the lower arch following two-stage surgical technique and Group 2: Patients were rehabilitated with complete mandibular overdenture supported by one-piece implants one on each side. Evaluation was made at the time of insertion, 6, 12, and 18 months after overdenture insertion, by measuring bacteriological changes around implants abutments. Results: Complete overdenture supported by one-piece implants showed better effect on the bacteriological changes as compared to that supported by two-piece implants. Conclusion: Complete overdenture supported by one-piece implants one on each side of the lower arch showed better effect on the bacteriological changes than using the same prosthesis supported by two-piece implants. PMID:26903697

Biocompatibility of composite resins

PubMed Central

Mousavinasab, Sayed Mostafa

2011-01-01

Dental materials that are used in dentistry should be harmless to oral tissues, so they should not contain any leachable toxic and diffusible substances that can cause some side effects. Reports about probable biologic hazards, in relation to dental resins, have increased interest to this topic in dentists. The present paper reviews the articles published about biocompatibility of resin-restorative materials specially resin composites and monomers which are mainly based on Bis-GMA and concerns about their degradation and substances which may be segregated into oral cavity. PMID:23372592

Investigation of Plasma Facing Components in Plasma Focus Operation

NASA Astrophysics Data System (ADS)

Roshan, M. V.; Babazadeh, A. R.; Kiai, S. M. Sadat; Habibi, H.; Mamarzadeh, M.

2007-09-01

Both aspects of the plasma-wall interactions, counter effect of plasma and materials, have been considered in our experiments. The AEOI plasma focus, Dena, has Filippov-type electrodes. The experimental results verify that neutron production increases using tungsten as an anode insert material, compared to the copper one. The experiments show decrement of the hardness of Aluminum targets outward the sides, from 135 to 78 in Vickers scale. The sputtering yield is about 0.0065 for deuteron energy of 50 keV.

Materials for pharmaceutical dosage forms: molecular pharmaceutics and controlled release drug delivery aspects.

PubMed

Mansour, Heidi M; Sohn, Minji; Al-Ghananeem, Abeer; Deluca, Patrick P

2010-09-15

Controlled release delivery is available for many routes of administration and offers many advantages (as microparticles and nanoparticles) over immediate release delivery. These advantages include reduced dosing frequency, better therapeutic control, fewer side effects, and, consequently, these dosage forms are well accepted by patients. Advances in polymer material science, particle engineering design, manufacture, and nanotechnology have led the way to the introduction of several marketed controlled release products and several more are in pre-clinical and clinical development.

Materials for Pharmaceutical Dosage Forms: Molecular Pharmaceutics and Controlled Release Drug Delivery Aspects

PubMed Central

Mansour, Heidi M.; Sohn, MinJi; Al-Ghananeem, Abeer; DeLuca, Patrick P.

2010-01-01

Controlled release delivery is available for many routes of administration and offers many advantages (as microparticles and nanoparticles) over immediate release delivery. These advantages include reduced dosing frequency, better therapeutic control, fewer side effects, and, consequently, these dosage forms are well accepted by patients. Advances in polymer material science, particle engineering design, manufacture, and nanotechnology have led the way to the introduction of several marketed controlled release products and several more are in pre-clinical and clinical development. PMID:20957095

Glove box shield

DOEpatents

Brackenbush, L.W.; Hoenes, G.R.

A shield for a glove box housing radioactive material is comprised of spaced apart clamping members which maintain three overlapping flaps in place therebetween. There is a central flap and two side flaps, the side flaps overlapping at the interior edges thereof and the central flap extending past the intersection of the side flaps in order to insure that the shield is always closed when the user wthdraws his hand from the glove box. Lead loaded neoprene rubber is the preferred material for the three flaps, the extent of lead loading depending upon the radiation levels within the glove box.

Side-Chain Effects on the Thermoelectric Properties of Fluorene-Based Copolymers.

PubMed

Liang, Ansheng; Zhou, Xiaoyan; Zhou, Wenqiao; Wan, Tao; Wang, Luhai; Pan, Chengjun; Wang, Lei

2017-09-01

Three conjugated polymers with alkyl chains of different lengths are designed and synthesized, and their structure-property relationship as organic thermoelectric materials is systematically elucidated. All three polymers show similar photophysical properties, thermal properties, and mechanical properties; however, their thermoelectric performance is influenced by the length of their side chains. The length of the alkyl chain significantly influences the electrical conductivity of the conjugated polymers, and polymers with a short alkyl chain exhibit better conductivity than those with a long alkyl chain. The length of the alkyl chain has little effect on the Seebeck coefficient. Only a slight increase in the Seebeck coefficient is observed with the increasing length of the alkyl chain. The purpose of this study is to provide comprehensive insight into fine-tuning the thermoelectric properties of conjugated polymers as a function of side-chain engineering, thereby providing a novel perspective into the design of high-performance thermoelectric conjugated polymers. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Long-term survival of endodontically treated, maxillary anterior teeth restored with either tapered or parallel-sided glass-fiber posts and full-ceramic crown coverage.

PubMed

Signore, Antonio; Benedicenti, Stefano; Kaitsas, Vassilios; Barone, Michele; Angiero, Francesca; Ravera, Giambattista

2009-02-01

This retrospective study investigated the clinical effectiveness over up to 8 years of parallel-sided and of tapered glass-fiber posts, in combination with either hybrid composite or dual-cure composite resin core material, in endodontically treated, maxillary anterior teeth covered with full-ceramic crowns. The study population comprised 192 patients and 526 endodontically treated teeth, with various degrees of hard-tissue loss, restored by the post-and-core technique. Four groups were defined based on post shape and core build-up materials, and within each group post-and-core restorations were assigned randomly with respect to root morphology. Inclusion criteria were symptom-free endodontic therapy, root-canal treatment with a minimum apical seal of 4mm, application of rubber dam, need for post-and-core complex because of coronal tooth loss, and tooth with at least one residual coronal wall. Survival rate of the post-and-core restorations was determined using Kaplan-Meier statistical analysis. The restorations were examined clinically and radiologically; mean observation period was 5.3 years. The overall survival rate of glass-fiber post-and-core restorations was 98.5%. The survival rate for parallel-sided posts was 98.6% and for tapered posts was 96.8%. Survival rates for core build-up materials were 100% for dual-cure composite and 96.8% for hybrid light-cure composite. For both glass-fiber post designs and for both core build-up materials, clinical performance was satisfactory. Survival was higher for teeth retaining four and three coronal walls.

Naphthalene Diimide Based n-Type Conjugated Polymers as Efficient Cathode Interfacial Materials for Polymer and Perovskite Solar Cells.

PubMed

Jia, Tao; Sun, Chen; Xu, Rongguo; Chen, Zhiming; Yin, Qingwu; Jin, Yaocheng; Yip, Hin-Lap; Huang, Fei; Cao, Yong

2017-10-18

A series of naphthalene diimide (NDI) based n-type conjugated polymers with amino-functionalized side groups and backbones were synthesized and used as cathode interlayers (CILs) in polymer and perovskite solar cells. Because of controllable amine side groups, all the resulting polymers exhibited distinct electronic properties such as oxidation potential of side chains, charge carrier mobilities, self-doping behaviors, and interfacial dipoles. The influences of the chemical variation of amine groups on the cathode interfacial effects were further investigated in both polymer and perovskite solar cells. We found that the decreased electron-donating property and enhanced steric hindrance of amine side groups substantially weaken the capacities of altering the work function of the cathode and trap passivation of the perovskite film, which induced ineffective interfacial modifications and declining device performance. Moreover, with further improvement of the backbone design through the incorporation of a rigid acetylene spacer, the resulting polymers substantially exhibited an enhanced electron-transporting property. Upon use as CILs, high power conversion efficiencies (PCEs) of 10.1% and 15.2% were, respectively, achieved in polymer and perovskite solar cells. Importantly, these newly developed n-type polymers were allowed to be processed over a broad thickness range of CILs in photovoltaic devices, and a prominent PCE of over 8% for polymer solar cells and 13.5% for perovskite solar cells can be achieved with the thick interlayers over 100 nm, which is beneficial for roll-to-roll coating processes. Our findings contribute toward a better understanding of the structure-performance relationship between CIL material design and solar cell performance, and provide important insights and guidelines for the design of high-performance n-type CIL materials for organic and perovskite optoelectronic devices.

Shifting Coronas Around Black Holes Artist Concept

NASA Image and Video Library

2015-10-27

A supermassive black hole is depicted in this artist's concept, surrounded by a swirling disk of material falling onto it. The purplish ball of light above the black hole, a feature called the corona, contains highly energetic particles that generate X-ray light. If you could view the corona with your eyes, it would appear nearly invisible since we can't see its X-ray light. The corona gathers inward (left), becoming brighter, before shooting away from the black hole (middle and right). Astronomers don't know why the coronas shift, but they have learned that this process leads to a brightening of X-ray light that can be observed by telescopes. Normally, before a black hole's corona shifts, there is already an effect at work called relativistic boosting. As X-ray light from the corona reflects off the black hole's surrounding disk of material -- which is traveling near half the speed of light -- the X-ray light becomes brightened, as seen on the left side of the illustration. This boosting occurs on the side of the disk where the material is traveling toward us. The opposite effect, a dimming of the X-ray light, occurs on the other side of the disk moving away from us. Another form of relativistic boosting happens when the corona shoots away from the black hole, and later collapses. Its X-ray light is also brightened as the corona travels toward us at very fast speeds, leading to X-ray flares. In 2014, NASA's Nuclear Spectroscopic Telescope Array, or NuSTAR, and Swift space telescopes witnessed an X-flare from the supermassive black hole in a distant galaxy called Markarian 335. The observations allowed astronomers to link a shifting corona to an X-ray flare for the first time. http://photojournal.jpl.nasa.gov/catalog/PIA20051

Method of fabricating high-density hermetic electrical feedthroughs

DOEpatents

Shah, Kedar G.; Pannu, Satinderpall S.; Delima, Terri L.

2015-06-02

A method of fabricating electrical feedthroughs selectively removes substrate material from a first side of an electrically conductive substrate (e.g. a bio-compatible metal) to form an array of electrically conductive posts in a substrate cavity. An electrically insulating material (e.g. a bio-compatible sealing glass) is then flowed to fill the substrate cavity and surround each post, and solidified. The solidified insulating material is then exposed from an opposite second side of the substrate so that each post is electrically isolated from each other as well as the bulk substrate. In this manner a hermetic electrically conductive feedthrough construction is formed having an array of electrical feedthroughs extending between the first and second sides of the substrate from which it was formed.

W-Band Transmission MeasurementS and X-Band Dielectric Properties Measurements for a Radome Material Sample

NASA Technical Reports Server (NTRS)

Cravey, Robin L.; Tiemsin, Pacita I.

1997-01-01

This paper describes measurements which were performed on a sample of radome material in the Electromagnetic Properties Measurements Laboratory (EPML). The purpose of the measurements described in this paper was to determine the one-way transmission loss through the flat panel of radome material for a frequency range of 84 to 94 GHz, for varying incidence angles. The panel, which was manufactured by Norton Performance Plastics Corporation, was provided to the EPML by TRW. The size of the panel is 40 in x 36 in x 0.422 in and consists of a foam material with one side coated with a smooth white coating (this side will be referred to as the front side). The dielectric properties of the foam material from the inside of the panel were also determined at X-band (8.2-12.4 GHz). The W-band free space measurements are presented first, followed by the X-band dielectric properties measurements.

Efficacy of Punch Elevation Combined with Fractional Carbon Dioxide Laser Resurfacing in Facial Atrophic Acne Scarring: A Randomized Split-face Clinical Study

PubMed Central

Faghihi, Gita; Nouraei, Saeid; Asilian, Ali; Keyvan, Shima; Abtahi-Naeini, Bahareh; Rakhshanpour, Mehrdad; Nilforoushzadeh, Mohammad Ali; Hosseini, Sayed Mohsen

2015-01-01

Background: A number of treatments for reducing the appearance of acne scars are available, but general guidelines for optimizing acne scar treatment do not exist. The aim of this study was to compare the clinical effectiveness and side effects of fractional carbon dioxide (CO2) laser resurfacing combined with punch elevation with fractional CO2 laser resurfacing alone in the treatment of atrophic acne scars. Materials and Methods: Forty-two Iranian subjects (age range 18–55) with Fitzpatrick skin types III to IV and moderate to severe atrophic acne scars on both cheeks received randomized split-face treatments: One side received fractional CO2 laser treatment and the other received one session of punch elevation combined with two sessions of laser fractional CO2 laser treatment, separated by an interval of 1 month. Two dermatologists independently evaluated improvement in acne scars 4 and 16 weeks after the last treatment. Side effects were also recorded after each treatment. Results: The mean ± SD age of patients was 23.4 ± 2.6 years. Clinical improvement of facial acne scarring was assessed by two dermatologists blinded to treatment conditions. No significant difference in evaluation was observed 1 month after treatment (P = 0.56). Their evaluation found that fractional CO2 laser treatment combined with punch elevation had greater efficacy than that with fractional CO2 laser treatment alone, assessed 4 months after treatment (P = 0.02). Among all side effects, coagulated crust formation and pruritus at day 3 after fractional CO2 laser treatment was significant on both treatment sides (P < 0.05). Conclusion: Concurrent use of fractional laser skin resurfacing with punch elevation offers a safe and effective approach for the treatment of acne scarring. PMID:26538695

The ins and outs of caulking

Treesearch

Charles Carll

2006-01-01

Effective water management involves understanding the roles of siding, trim, fenestration units, flashing, and (where appropriate) caulk seals and how these entities interface with each other. Where caulk seals are used, their geometry and dimensions are important to joint performance, as is the care with which they are executed. In selection of caulking material,...

Effect of quantum tunneling on spin Hall magnetoresistance

NASA Astrophysics Data System (ADS)

Ok, Seulgi; Chen, Wei; Sigrist, Manfred; Manske, Dirk

2017-02-01

We present a formalism that simultaneously incorporates the effect of quantum tunneling and spin diffusion on the spin Hall magnetoresistance observed in normal metal/ferromagnetic insulator bilayers (such as Pt/Y3Fe5O12) and normal metal/ferromagnetic metal bilayers (such as Pt/Co), in which the angle of magnetization influences the magnetoresistance of the normal metal. In the normal metal side the spin diffusion is known to affect the landscape of the spin accumulation caused by spin Hall effect and subsequently the magnetoresistance, while on the ferromagnet side the quantum tunneling effect is detrimental to the interface spin current which also affects the spin accumulation. The influence of generic material properties such as spin diffusion length, layer thickness, interface coupling, and insulating gap can be quantified in a unified manner, and experiments that reveal the quantum feature of the magnetoresistance are suggested.

Indium-incorporation efficiency in semipolar (11-22) oriented InGaN-based light emitting diodes

NASA Astrophysics Data System (ADS)

Monavarian, Morteza; Metzner, Sebastian; Izyumskaya, Natalia; Okur, Serdal; Zhang, Fan; Can, Nuri; Das, Saikat; Avrutin, Vitaliy; Özgür, Ümit; Bertram, Frank; Christen, Jürgen; Morkoç, Hadis

2015-03-01

Reduced electric field in semipolar (1122) GaN/InGaN heterostructures makes this orientation attractive for high efficiency light emitting diodes. In this work, we investigated indium incorporation in semipolar (1122) GaN grown by metal-organic chemical vapor deposition on planar m-plane sapphire substrates. Indium content in the semipolar material was compared with that in polar c-plane samples grown under the same conditions simultaneously side by side on the same holder. The investigated samples incorporated dual GaN/InGaN/GaN double heterostructures with 3nm wide wells. In order to improve optical quality, both polar and semipolar templates were grown using an in-situ epitaxial lateral overgrowth (ELO) technique. Indium incorporation efficiency was derived from the comparison of PL spectra measured on the semipolar and polar structures at the highest excitation density, which allowed us to minimize the effect of quantum confined Stark effect on the emission wavelength. Our data suggests increased indium content in the semipolar material by up to 3.0%, from 15% In in c- GaN to 18% In in (1122) GaN.

Correlation of mastication and masticatory movements and effect of chewing side preference.

PubMed

Farias Gomes, Simone Guimarães; Custodio, William; Moura Jufer, Juliana Silva; Del Bel Cury, Altair Antoninha; Rodrigues Garcia, Renata Cunha Matheus

2010-01-01

The aims of this study were to correlate masticatory performance with mandibular movements during mastication, and to evaluate masticatory performance and mandibular movements of subjects with different types of mastication. Seventy-eight healthy dentate subjects were selected and divided into 2 groups: bilateral and unilateral chewers. This classification was set by using kinesiography during mastication of an artificial material. Unilateral mastication was defined as the majority of the cycles took place at one specific side. The same tracings used to define type of mastication were used to evaluate mandibular movements by means of its parameters. Masticatory performance was analyzed by comminution of the artificial material and a sieving method. Statistical analysis was performed by Spearman's correlation method, and Mann-Whitney and Student's t-test, when appropriate, at 5% significance level. No correlation was found between masticatory performance and parameters of mandibular movement during mastication. Bilateral chewers presented significantly better (p<0.05) masticatory performance than unilateral ones, however no differences in parameters of mandibular movement were found between groups. Within the limits of this study, it may be concluded that parameters of jaw movements during mastication are not related to masticatory performance, and that the presence of a preferred chewing side worsens mastication.

Design, integration and preliminary results of the IXV Catalysis experiment

NASA Astrophysics Data System (ADS)

Viladegut, Alan; Panerai, F.; Chazot, O.; Pichon, T.; Bertrand, P.; Verdy, C.; Coddet, C.

2017-06-01

The CATalytic Experiment (CATE) is an in-flight demonstration of catalysis effects at the surface of thermal protection materials. A high-catalytic coating was applied over the baseline ceramic material on the windward side of the intermediate experimental vehicle (IXV). The temperature jump due to different catalytic activities was detected during re-entry through measurements made with near-surface thermocouples on the windward side of the vehicle. The experiment aimed at contributing to the development and validation of gas/surface interaction models for re-entry applications. The present paper summarizes the design of CATE and its integration on the windward side of the IXV. Results of a qualification campaign at the Plasmatron facility of the von Karman Institute for Fluid Dynamics are presented. They provided an experimental evidence of the temperature jump at the low-to-high catalytic interface of the heat shield under aerothermal conditions relevant to the actual IXV flight. These tests also gave confidence so that the high-catalytic patch would not endanger the integrity of the vehicle and the safety of the mission. A preliminary assessment of flight data from the thermocouple measurements shows consistency with results of the qualification tests.

The Janus effect on superhydrophilic Cu mesh decorated with Ni-NiO/Ni(OH)2 core-shell nanoparticles for oil/water separation

NASA Astrophysics Data System (ADS)

Luo, Zhi-Yong; Lyu, Shu-Shen; Fu, Yuan-Xiang; Heng, Yi; Mo, Dong-Chuan

2017-07-01

Janus effect has been studied for emerging materials like Janus membranes, Janus nanoparticles, etc., and the applications including fog collection, oil/water separation, CO2 removal and stabilization of multiphasic mixtures. However, the Janus effect on oil/water separation is still unclear. Herein, Janus Cu mesh decorated with Ni-NiO/Ni(OH)2 core-shell nanoparticles is synthesized via selective electrodeposition, in which we keep one side of Cu mesh (Janus A) to be superhydrophilic, while manipulate the wettability of another side (Janus B) from hydrophobic to superhydrophilic. Experimental results indicate that Cu mesh with both-side superhydrophilic shows the superior oil/water separation performance (separation efficiency >99.5%), which is mainly due to its higher water capture percentage as well as larger oil intrusion pressure. Further, we demonstrate the orientation of Janus membranes for oil/water separation, and summarize that the wettability of the upper surface plays a more important role than the lower surface to achieve remarkable performance. Our work provides a clear insight of Janus effect on oil/water separation, it is significative to design high-performance membranes for oil/water separation and many other applications.

2. BUILDING 413, WEST SIDE AND OBLIQUE VIEW OF NORTH ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

2. BUILDING 413, WEST SIDE AND OBLIQUE VIEW OF NORTH SIDE, FROM INTERSECTION OF C AND 4TH STREETS, LOOKING SOUTHEAST. - Oakland Naval Supply Center, Heavy Materials & Paint-Oil Storehouses, Between Fourth & Sixth streets, between B & D Streets, Oakland, Alameda County, CA

Practical issues in laser cleaning of stone and painted artefacts: optimisation procedures and side effects

NASA Astrophysics Data System (ADS)

Pouli, Paraskevi; Oujja, Mohamed; Castillejo, Marta

2012-02-01

In the last twenty years lasers have acquired an important role in the study and the preservation of Cultural Heritage (CH) objects and Monuments, as they have effectively illuminated a number of complex diagnostic and restoration problems. Their unique properties have enabled their use in a wide range of conservation applications, since they ensure interventions with precise control, material selectivity and immediate feedback. Surface cleaning, based on laser ablation, is a delicate, critical and irreversible process, which, given the multitude of materials that may be present on a CH object and the often fragile or precarious condition of the original surfaces, is fraught with many potential complications. Therefore it is crucial to choose the best possible laser cleaning methodology for each individual case, which involves optimising the laser parameters according to material properties, as well as the thorough knowledge of the ablation mechanisms involved. In this context the systematic investigation and elucidation of potential damage or side effects occurring upon cleaning is essential, as it delineates the possibilities and limitations of laser ablation and allows the fine-tuning of the operating parameters for a successful cleaning intervention. This paper is an overview of studies investigating the mechanisms which are responsible for the laser-induced discoloration effects. Emphasis is given on the yellowing coloration observed on stonework upon infrared (IR) ablation of pollution encrustations, while the various theories introduced to approach the different physical and/or chemical processes and mechanisms responsible for such side effects are discussed. In this respect the different laser cleaning methodologies, which are based on the use of laser systems with different pulse durations and wavelength characteristics, introduced in order to rectify or prevent discoloration on stonework are presented. In parallel, the darkening phenomena which occur upon laser irradiation of painted surfaces are also considered. Studies on series of model paints performed in order to understand the sensitivity of pigments to laser irradiation are critically reviewed. In this respect the importance of the optimal wavelength and pulse-duration selection for a safe and controlled laser cleaning intervention is also addressed.

From Semi- to Full-Two-Dimensional Conjugated Side-Chain Design: A Way toward Comprehensive Solar Energy Absorption

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chao, Pengjie; Wang, Huan; Qu, Shiwei

Two polymers with fully two-dimensional (2D) conjugated side chains, 2D-PTB-Th and 2D-PTB-TTh, were synthesized and characterized through simultaneously integrating the 2D-TT and the 2D-BDT monomers onto the polymer backbone. Resulting from the synergistic effect from the conjugated side chains on both monomers, the two polymers showed remarkably efficient absorption of the sunlight and improved pi-pi intermolecular interactions for efficient charge carrier transport. The optimized bulk heterojunction device based on 2D-PTB-Th and PC71BM shows a higher PCE of 9.13% compared to PTB7-Th with a PCE of 8.26%, which corresponds to an approximately 10% improvement in solar energy conversion. The fully 2D-conjugatedmore » side-chain concept reported here developed a new molecular design strategy for polymer materials with enhanced sunlight absorption and efficient solar energy conversion.« less

Preventive effects of various types of footwear and cleaning methods on dermatophyte adhesion.

PubMed

Tanaka, Kumi; Katoh, Takuro; Irimajiri, Junya; Taniguchi, Hiroko; Yokozeki, Hiroo

2006-08-01

Tinea pedis is contagious and typically spreads from infected to non-infected persons. The purpose of this study was to evaluate the efficacy of footwear in preventing tinea pedis adhesion. Using the stamp culture method, we investigated the effectiveness of preventing dermatophyte passage by the wearing of stockings made of nylon, socks made of cotton and tabi (Japanese socks), as well as the effect of removing dermatophytes from these items by washing with soap, cold water and cold water after turning inside-out. For sandals, sneakers and boots, we also investigated the effect of dermatophyte removal by pouring cold water into the footwear, wiping with a wet towel, and pouring boiling water into the footwear. The wearing of socks or tabi was effective in preventing passage of dermatophytes. The stocking material proved to be too thin to prevent passage. On the inner side of socks (the side of the sole), all treatments were effective at removing dermatophytes, but on the outer side of socks (the side touching the surface of the sandals), the treatment of washing in cold water after turning inside-out resulted in significantly more dermatophytes as compared with the other treatments. Pouring cold water, wiping with a wet towel and pouring boiling water were all effective for removing dermatophytes from sandals and sneakers. However, for boots, the treatment of pouring cold water was less effective. To prevent the adhesion of dermatophytes to sandals, wearing socks or tabi was effective, and the treatments of washing socks in cold water after turning inside-out and of pouring cold water into the boots were less effective than the others.

The Optical Janus Effect: Asymmetric Structural Color Reflection Materials.

PubMed

England, Grant T; Russell, Calvin; Shirman, Elijah; Kay, Theresa; Vogel, Nicolas; Aizenberg, Joanna

2017-08-01

Structurally colored materials are often used for their resistance to photobleaching and their complex viewing-direction-dependent optical properties. Frequently, absorption has been added to these types of materials in order to improve the color saturation by mitigating the effects of nonspecific scattering that is present in most samples due to imperfect manufacturing procedures. The combination of absorbing elements and structural coloration often yields emergent optical properties. Here, a new hybrid architecture is introduced that leads to an interesting, highly directional optical effect. By localizing absorption in a thin layer within a transparent, structurally colored multilayer material, an optical Janus effect is created, wherein the observed reflected color is different on one side of the sample than on the other. A systematic characterization of the optical properties of these structures as a function of their geometry and composition is performed. The experimental studies are coupled with a theoretical analysis that enables a precise, rational design of various optical Janus structures with highly controlled color, pattern, and fabrication approaches. These asymmetrically colored materials will open applications in art, architecture, semitransparent solar cells, and security features in anticounterfeiting materials. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Investigation of the Environmental Durability of a Powder Metallurgy Material

NASA Technical Reports Server (NTRS)

Ward, LaNita D.

2004-01-01

PM304 is a NASA-developed composite powder metallurgy material that is being developed for high temperature applications such as bushings in high temperature industrial furnace conveyor systems. My goal this summer was to analyze and evaluate the effects that heat exposure had on the PM304 material at 500 C and 650 C. The material is composed of Ni-Cr, Ag, Cr2O3, and eutectic BaF2-CaF2. PM304 is designed to eliminate the need for oil based lubricants in high temperature applications, while reducing friction and wear. However, further investigation was needed to thoroughly examine the properties of PM304. The effects of heat exposure on PM304 bushings were investigated. This investigation was necessary due to the high temperatures that the material would be exposed to in a typical application. Each bushing was cut into eight sections. The specimens were heated to 500 C or 650 C for time intervals from 1 hr to 5,000 hrs. Control specimens were kept at room temperature. Weight and thickness measurements were taken before and after the bushing sections were exposed to heat. Then the heat treated specimens were mounted and polished side by side with the control specimens. This enabled optical examination of the material's microstructure using a metallograph. The specimens were also examined with a scanning electron microscope (SEM). The microstructures were compared to observe the effects of the heat exposure. Chemical analysis was done to investigate the interactions between Ni-Cr and BaF2-CaF2 and between Cr2O3 and BaF2-CaF2 at high temperature. To observe this, the two compounds that were being analyzed were mixed in a crucible in varied weight percentages and heated to 1100 C in a furnace for approximately two hours. Then the product was allowed to cool and was then analyzed by X-ray diffraction. Interpretation of the results is in progress.

A One-Year Evaluation of a Free Fissure Sealant Program

PubMed Central

M, Bakhtiar; N, Azadi; A, Golkari

2016-01-01

Statement of Problem: Pit and fissure sealant therapy has been approved as an effective measure in the prevention of occlusal dental caries. Resin based materials are the most common materials used worldwide. A variety of resin based fissure sealants are produced and used. Most of them have been presented with ideal results in research environment. However, their effectiveness in the real life, especially in a mass application program such as Iran’s oral health reform plan is not clear. Objectives: To evaluate the longevity of different fissure sealant applied in Iran’s oral health reform plan in Fars Province (south of Iran) after one year. Materials and Methods: Seven counties were selected. One hundred 6- to 8-year-old school children who had undergone fissure sealant therapy in spring 2015 were randomly selected from each county. Their first molars were examined to evaluate the status of the fissure sealants which were applied one year ago. Data on the type/brand of fissure sealant materials, type and experience of clinicians who applied them, existence of a chair-side assistant, and whether the children were caries-free at the time of fissure sealant application were collected from the existing reports. Results: Data of 1974 teeth from 598 children were used for the final analysis. The effects of type/brand of the material was significant on the final results and remained significant (p < 0.001) after adjustments for the level of fluoride, urban/rural area, upper/lower jaw, type of clinician who applied the sealant, existence of a chair-side assistant, and child’s gender, age, and being caries-free. Conclusions: Many factors affect the success rate of a fissure sealant therapy program. The type/brand of the material remained significantly related to the success rate of the fissure sealant even after adjustments for other influencing factors. In this study, ClinproTM Sealant (3M/ESPE, USA) showed better longevity after one year of application. PMID:28959758

Bottom-up on-crystal in-chip formation of a conducting salt and a view of its restructuring: from organic insulator to conducting "switch" through microfluidic manipulation.

PubMed

Puigmartí-Luis, Josep; Paradinas, Markos; Bailo, Elena; Rodriguez-Trujillo, Romen; Pfattner, Raphael; Ocal, Carmen; Amabilino, David B

2015-06-01

The chemical modification of an immobilized single crystal in a fluid cell is reported, whereby a material with switching functions is generated in situ by generating a chemical reagent in the flow. Crystals of the insulating organic crystal of TCNQ (tetracyanoquinodimethane) were grown in a microfluidic channel and were trapped using a pneumatic valve, a nascent technique for materials manipulation. They were subsequently reduced using solution-deposited silver to provide a conducting material in situ by a heterogeneous reaction. Removal of the new material from the chip proved it to be the silver salt of reduced TCNQ. Uniquely, conducting atomic force microscope (CAFM) studies show three regions in the solid. The localized original neutral organic material crystal is shown to be an insulator but to produce areas with Ohmic conducting characteristics after reduction. This inhomogeneous doping provides an opportunity for probing electrical materials properties side by side. Measurements with the CAFM witness this conducting material where the TCNQ is fully transformed to the silver salt. Additionally, an intermediate phase is observed that exhibits bipolar resistive switching typical of programmable resistive memories. Raman microscopy proves the conversion of the material in specific regions and clearly defines the intermediate phase region that could be responsible for the switching effect in related materials. This kind of "on crystal chemistry" exploiting immobilization and masking by a pneumatic clamp in a microfluidic channel shows how material can be selectively converted to give different functionalities in the same material piece, even though it is not a single crystal to single crystal conversion, and beckons exploitation for the preparation of systems relevant for molecular electronics as well as other areas where chemical manipulation of single crystals could be beneficial.

Space ultra-vacuum facility and method of operation

NASA Technical Reports Server (NTRS)

Naumann, Robert J. (Inventor)

1986-01-01

A wake shield facility providing an ultrahigh vacuum level for space processing is described. The facility is in the shape of a truncated, hollow hemispherical section, one side of the shield convex and the other concave. The shield surface is preferably made of material that has low out-gassing characteristics such as stainless steel. A material sample supporting fixture in the form of a carousel is disposed on the convex side of the shield at its apex. Movable arms, also on the convex side, are connected by the shield in proximity to the carousel, the arms supporting processing fixtures, and providing for movement of the fixtures to predetermined locations required for producing interations with material samples. For MBE processes a vapor jet projects a stream of vaporized material onto a sample surface. The fixtures are oriented to face the surface of the sample being processed when in their extended position, and when not in use they are retractable to a storage position. The concave side of the shield has a support structure including metal struts connected to the shield, extending radially inward. The struts are joined to an end plate disposed parallel to the outer edge of the shield. This system eliminates outgassing contamination.

Method of beam welding metallic parts together and apparatus for doing same

DOEpatents

Lewandowski, Edward F.; Cassidy, Dale A.; Sommer, Robert G.

1987-01-01

The disclosed method provides for temporarily clamping a metallic piece to one side of a metallic plate while leaving the opposite side of the plate exposed, and providing a heat conductive heat sink body configured to engage the adjacent portions of such one side of the plate and the piece at all regions proximate to but not at the interface between these components. Such exposed side of such plate is then subjected to an electron welding beam, in exact registry with but opposite to the piece. The electron welding beam is supplied with adequate energy for penetrating through the plate, across the interface, and into the piece, whereby the electron welding beam produces molten material from both the plate and the piece in the region of the interface. The molten material flows into any interstices that may exist in the interface, and upon cooling solidifies to provide a welded joint between the plate and piece, where the interface was, virtually without any interstices. The heat sink material prevents the molten material from extruding beyond what was the interface, to provide a clean welded joint. The heat sink body also mechanically holds the plate and piece together prior to the actual welding.

Method of beam welding metallic parts together and apparatus for doing same

DOEpatents

Lewandowski, E.F.; Cassidy, D.A.; Sommer, R.G.

1985-11-29

This method provides for temporarily clamping a metallic piece to one side of a metallic plate while leaving the opposite side of the plate exposed, and providing a heat conductive heat sink body configured to engage the adjacent portions of such one side of the plate and the piece at all regions proximate to but not at the interface between these components. The exposed side of such plate is then subjected to an electron welding beam, in exact registry with but opposite to the piece. The electron welding beam is supplied with adequate energy for penetrating through the plate, across the interface, and into the piece, whereby the electron welding beam produces molten material from both the plate and the piece in the region of the interface. The molten material flows into any interstices that may exist in the interface, and upon cooling solidifies to provide a welded joint between the plate and piece, where the interface was, virtually without any interstices. The heat sink material prevents the molten material from extrucing beyond what was the interface, to provide a clean welded joint. The heat sink body also mechanically holds the plate and piece together prior to the actual welding.

SYNERGISTIC DEGRADATION OF DENTIN BY CYCLIC STRESS AND BUFFER AGITATION

PubMed Central

Orrego, Santiago; Romberg, Elaine; Arola, Dwayne

2015-01-01

Secondary caries and non-carious lesions develop in regions of stress concentrations and oral fluid movement. The objective of this study was to evaluate the influence of cyclic stress and fluid movement on material loss and subsurface degradation of dentin within an acidic environment. Rectangular specimens of radicular dentin were prepared from caries-free unrestored 3rd molars. Two groups were subjected to cyclic cantilever loading within a lactic acid solution (pH=5) to achieve compressive stresses on the inner (pulpal) or outer sides of the specimens. Two additional groups were evaluated in the same solution, one subjected to movement only (no stress) and the second held stagnant (control: no stress or movement). Exterior material loss profiles and subsurface degradation were quantified on the two sides of the specimens. Results showed that under cyclic stress material loss was significantly greater (p≤0.0005) on the pulpal side than on the outer side and significantly greater (p≤0.05) under compression than tension. However, movement only caused significantly greater material loss (p≤0.0005) than cyclic stress. Subsurface degradation was greatest at the location of highest stress, but was not influenced by stress state or movement. PMID:25637823

Experimental study of 2-layer regenerators using Mn-Fe-Si-P materials

NASA Astrophysics Data System (ADS)

Christiaanse, T. V.; Trevizoli, P. V.; Misra, Sumohan; Carroll, Colman; van Asten, David; Zhang, Lian; Teyber, R.; Govindappa, P.; Niknia, I.; Rowe, A.

2018-03-01

This work describes an experimental study of a two layer active magnetic regenerator with varying transition temperature spacing. The transition temperature of the materials is based on the specific heat peak of the materials. A transition temperature based on the average of the heating and cooling curves at zero Tesla field value is used to refer to the materials throughout this paper. This study uses five Mn-Fe-Si-P materials with transition temperatures of 294.6 K, 292.3 K, 290.7 K, 282.5 K and 281.4 K. Six different regenerators are tested. A reference configuration is tested using the 294.6 K material a hot side layer and with a second passive layer of lead spheres as cold side layer. Followed by four configurations that use the same 294.6 K material as hot side layer, but where each configuration uses a different cold side material. For the second active layer the materials are used in sequence; 292.3 K, 290.7 K, 282.5 K and 281.4K. Lastly, a sixth configuration uses the 292.3 K and 282.5 K materials. For each configuration, the temperature span is measured for rejection temperatures from 40 °C to 9 °C and at 0 W and 2 W applied load. Experimental results for temperature span and exergetic cooling power are compared based on the differences from the reference configuration. Materials are analysed based on material performance metrics such as peak adiabatic temperature change, peak entropy change and RCP(s) values. For the cases considered, a closer transition temperature spacing generally gives a greater temperature span and exergetic cooling power than further spaced materials, even when the combined materials have comparatively lower performance metrics. When two materials with higher RCP(s) values with large transition temperature spacing are compared to materials with lower RCP(s) values but, closer transition temperature spacing a higher exergetic cooling power and temperature span is found for the latter.

Glove box shield

DOEpatents

Brackenbush, Larry W.; Hoenes, Glenn R.

1981-01-01

According to the present invention, a shield for a glove box housing radioactive material is comprised of spaced apart clamping members which maintain three overlapping flaps in place therebetween. There is a central flap and two side flaps, the side flaps overlapping at the interior edges thereof and the central flap extending past the intersection of the side flaps in order to insure that the shield is always closed when the user withdraws his hand from the glove box. Lead loaded neoprene rubber is the preferred material for the three flaps, the extent of lead loading depending upon the radiation levels within the glove box.

Photogeology: Part A: relative ages of some near-side and far-side terra plains based on Apollo 16 metric photography

USGS Publications Warehouse

Soderblom, Laurence A.; Boyce, Joseph M.

1972-01-01

The materials of most light or terra plains predate the lunar maria and postdate the Imbrian event. In the vicinity of the Imbrium Basin, these materials have been called the Cayley Formation (ref. 29-3) but because of the subtle diversity of the terra plains over the near side, Whilhelms and McCauley (ref. 29-4) simply called these materials Imbrian plains (Ip). The age relationships between the light plains and the Fra Mauro Formation are of principal importance in placing the Apollo 14, 15, and 16 samples in a regional context and in understanding the transitional period between the enhanced cratering rate of pre-Imbrian time and the comparatively quiescent period of impact cratering since the generation of mare surfaces.

The role of intravenous immunoglobulin in treatment of mucous membrane pemphigoid: A review of literature

PubMed Central

Tavakolpour, Soheil

2016-01-01

Background: Mucous membrane pemphigoid (MMP) is considered an autoimmune blistering disease that predominantly affects mucous membranes. Various treatments are available for controlling the diseases, but not all of them may respond. Materials and Methods: PubMed and Google Scholar were searched for all the associated studies until 2015, using the keywords such as “cicatricial pemphigoid” or “ocular pemphigoid” or “mucous membrane pemphigoid” or “MMP” and “intravenous immunoglobulin” or “IVIg” to find all the relevant studies. The last search update was for September 2, 2015. Among the searched items, only English studies were included in the review. Results: After excluding nonrelevant studies, 13 studies with a total number of seventy patients with MMP who were under treatment with IVIg were analyzed. The 65 patients responded completely, one did not respond, two had partially responded, and the remaining two patients stopped IVIg therapy, which resulted in ocular cicatricial pemphigoid progression. Majority of the studies reported mild adverse effects while two of them did not report any unwanted side effect. The most common side effect was headache, followed by nausea. Most of the patients who had a cessation of IVIg therapy before achieving clinical remission experienced the disease progression. Conclusion: Overall, it can be concluded that IVIg therapy was very helpful in treatment of MMP patients who did not respond to conventional therapy or stopped using them for various side effects. Adverse effects associated with IVIg therapy were considerably lower than conventional therapy that can lead toward treatment with this agent in patients who suffer from severe side effects. PMID:27904583

IPS Empress crown system: three-year clinical trial results.

PubMed

Sorensen, J A; Choi, C; Fanuscu, M I; Mito, W T

1998-02-01

The IPS Empress system is a highly esthetic hot pressed glass ceramic material for fabrication of single crowns. Adhesive cementation of the system not only contributes to the esthetics but is necessary for increased strength of the crown. The purpose of this prospective clinical trials was to evaluate the longevity of 75 adhesively cemented Empress full crowns. An additional aim was to assess the adhesive cementation methodology and potential side effects. At the three-year point, one molar crown fractured for a 1.3 percent failure rate. The resin cementation technique that was employed exhibited a low incidence of microleakage with few clinical side effects. There was a 5.6 percent incidence of post-cementation sensitivity, with all symptoms subsiding by eight weeks. None of the crowns in the study required endodontic therapy.

49 CFR 238.217 - Side structure.

Code of Federal Regulations, 2011 CFR

2011-10-01

... of the material used to that of mild open-hearth steel for a car whose structural members are made of a higher strength steel. (b) Sheathing. (1) Outside sheathing of mild, open-hearth steel when used flat, without reinforcement (other than side posts) in a side frame of modified girder or semi...

The effects of gas mixtures on ion engine erosion and performance

NASA Technical Reports Server (NTRS)

Garner, Charles E.; Brophy, John R.; Aston, Graeme

1987-01-01

Erosion measurements were performed on a modified J-series 30 cm ion engine operating on xenon propellant. Erosion data was obtained by measuring the trench depth etched into masked polished metal samples for test durations of up to 24 hours. The data indicates that erosion is greatest at the cathode side of the baffle, with tantalum being the material with the least erosion of all materials tested. There is a clear indication of a significant reduction in erosion of all materials tested when nitrogen is added to the propellant. The technique used in these experiments requires test samples which are extremely smooth and flat.

Bottlebrush-Guided Polymer Crystallization Resulting in Supersoft and Reversibly Moldable Physical Networks

DOE Office of Scientific and Technical Information (OSTI.GOV)

Daniel, William F. M.; Xie, Guojun; Vatankhah Varnoosfaderani, Mohammad

The goal of this study is to use ABA triblock copolymers with central bottlebrush B segments and crystalline linear chain A segments to demonstrate the effect of side chains on the formation and mechanical properties of physical networks cross-linked by crystallites. For this purpose, a series of bottlebrush copolymers was synthesized consisting of central amorphous bottlebrush polymer segments with a varying degree of polymerization (DP) of poly(n-butyl acrylate) (PnBA) side chains and linear tail blocks of crystallizable poly(octadecyl acrylate-stat-docosyl acrylate) (poly(ODA-stat-DA)). The materials were generated by sequential atom transfer radical polymerization (ATRP) steps starting with a series of bifunctional macroinitiatorsmore » followed by the growth of two ODA-stat-DA linear-chain tails and eventually growing poly(nBA) side chains with increasing DPs. Crystallization of the poly(ODA-stat-DA) tails resulted in a series of reversible physical networks with bottlebrush strands bridging crystalline cross-links. They displayed very low moduli of elasticity of the order of 10 3–10 4 Pa. These distinct properties are due to the bottlebrush architecture, wherein densely grafted side chains play a dual role by facilitating disentanglement of the network strands and confining crystallization of the linear-chain tails. This combination leads to physical cross-linking of supersoft networks without percolation of the crystalline phase. The cross-link density was effectively controlled by the DP of the side chains with respect to the DP of the linear tails (n A). Furthermore, shorter side chains allowed for crystallization of the linear tails of neighboring bottlebrushes, while steric repulsion between longer side chains hindered the phase separation and crystallization process and prevented network formation.« less

Bottlebrush-Guided Polymer Crystallization Resulting in Supersoft and Reversibly Moldable Physical Networks

DOE PAGES

Daniel, William F. M.; Xie, Guojun; Vatankhah Varnoosfaderani, Mohammad; ...

2017-02-24

The goal of this study is to use ABA triblock copolymers with central bottlebrush B segments and crystalline linear chain A segments to demonstrate the effect of side chains on the formation and mechanical properties of physical networks cross-linked by crystallites. For this purpose, a series of bottlebrush copolymers was synthesized consisting of central amorphous bottlebrush polymer segments with a varying degree of polymerization (DP) of poly(n-butyl acrylate) (PnBA) side chains and linear tail blocks of crystallizable poly(octadecyl acrylate-stat-docosyl acrylate) (poly(ODA-stat-DA)). The materials were generated by sequential atom transfer radical polymerization (ATRP) steps starting with a series of bifunctional macroinitiatorsmore » followed by the growth of two ODA-stat-DA linear-chain tails and eventually growing poly(nBA) side chains with increasing DPs. Crystallization of the poly(ODA-stat-DA) tails resulted in a series of reversible physical networks with bottlebrush strands bridging crystalline cross-links. They displayed very low moduli of elasticity of the order of 10 3–10 4 Pa. These distinct properties are due to the bottlebrush architecture, wherein densely grafted side chains play a dual role by facilitating disentanglement of the network strands and confining crystallization of the linear-chain tails. This combination leads to physical cross-linking of supersoft networks without percolation of the crystalline phase. The cross-link density was effectively controlled by the DP of the side chains with respect to the DP of the linear tails (n A). Furthermore, shorter side chains allowed for crystallization of the linear tails of neighboring bottlebrushes, while steric repulsion between longer side chains hindered the phase separation and crystallization process and prevented network formation.« less

16. ARAII Administration building ARA613. South (front) and east sides. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

16. ARA-II Administration building ARA-613. South (front) and east sides. Camera facing northwest. Sign at left corner of building says, "Fuels and materials division, materials joining research and development laboratory." Part of south wall already has been demolished. Sign on roof railing says, "Danger--Abestos." Ineel photo no. 2-3. - Idaho National Engineering Laboratory, Army Reactors Experimental Area, Scoville, Butte County, ID

Percolation effect in thick film superconductors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sali, R.; Harsanyi, G.

1994-12-31

A thick film superconductor paste has been developed to study the properties of granulated superconductor materials, to observe the percolation effect and to confirm the theory of the conducting mechanism in the superconducting thick films. This paste was also applied to make a superconducting planar transformer. Due to high T{sub c} and advantageous current density properties the base of the paste was chosen to be of Bi(Pb)SrCaCuO system. For contacts a conventional Ag/Pt paste was used. The critical temperature of the samples were between 110 K and 115 K depending on the printed layer thickness. The critical current density atmore » the boiling temperature of the liquid He- was between 200-300 A/cm{sup 2}. The R(T) and V(I) functions were measured with different parameters. The results of the measurements have confirmed the theory of conducting mechanism in the material. The percolation structure model has been built and described. As an application, a superconducting planar thick film transformer was planned and produced. Ten windings of the transformer were printed on one side of the alumina substrate and one winding was printed on the other side. The coupling between the two sides was possible through the substrate. The samples did not need special drying and firing parameters. After the preparation, the properties of the transformer were measured. The efficiency and the losses were determined. Finally, some fundamental advantages and problems of the process were discussed.« less

Percolation effect in thick film superconductors: Using a Bi(Pb)SrCaCuO based paste to prepare a superconducting planar transformer

NASA Technical Reports Server (NTRS)

Sali, Robert; Harsanyi, Gabor

1995-01-01

A thick film superconductor paste has been developed to study the properties of granulated superconductor materials, to observe the percolation effect and to confirm the theory of the conducting mechanism in the superconducting thick films. This paste was also applied to make a superconducting planar transformer. Due to the T(sub c) and advantageous current density properties the base of the past was chosen to be of Bi(Pb)SrCaCu) system. For contacts a conventional Ag/Pt paste was used. The critical temperature of the samples were between 110 K and 115 K depending on the printed layer thickness. The critical current density -at the boiling temperature of the liquid He- was between 200 - 300 A/sq cm. The R(T) and V(I) functions were measured with different parameters. The results of the measurements have confirmed the theory of conducting mechanism in the material. The percolation structure model has been built and described. As an application, a superconducting planar thick film transformer was planned and produced. Ten windings of the transformer were printed on one side of the alumina substrate and one winding was printed on the other side. The coupling between the two sides was possible through the substrate. The samples did not need special drying and firing parameters. After the preparation, the properties of the transformer were measured. The efficiency ans the losses were determined. Finally, some fundamental advantages and problems of the process were discussed.

A Tool for Learning or a Tool for Cheating? The Many-Sided Effects of a Participatory Student Website in Mass Higher Education

ERIC Educational Resources Information Center

Stöckelová, Tereza; Virtová, Tereza

2015-01-01

This paper is a case study of the genesis, operation and, in particular, the educational effects of a participatory website established and run by students of one of the largest universities in the Czech Republic, the purpose of which is to enable students to share study materials, essays and evaluations of staff and courses. We study the rise of…

Polysaccharide-based Noncovalent Assembly for Targeted Delivery of Taxol

NASA Astrophysics Data System (ADS)

Yang, Yang; Zhang, Ying-Ming; Chen, Yong; Chen, Jia-Tong; Liu, Yu

2016-01-01

The construction of synthetic straightforward, biocompatible and biodegradable targeted drug delivery system with fluorescent tracking abilities, high anticancer activities and low side effects is still a challenge in the field of biochemistry and material chemistry. In this work, we constructed targeted paclitaxel (Taxol) delivery nanoparticles composed of permethyl-β-cyclodextrin modified hyaluronic acid (HApCD) and porphyrin modified paclitaxel prodrug (PorTaxol), through host-guest and amphiphilic interactions. The obtained nanoparticles (HATXP) were biocompatible and enzymatic biodegradable due to their hydrophilic hyaluronic acid (HA) shell and hydrophobic Taxol core, and exhibited specific targeting internalization into cancer cells via HA receptor mediated endocytosis effects. The cytotoxicity experiments showed that the HATXP exhibited similar anticancer activities to, but much lower side effects than commercial anticancer drug Taxol. The present work would provide a platform for targeted paclitaxel drug delivery and a general protocol for the design of advanced multifunctional nanoscale biomaterials for targeted drug/gene delivery.

Fractionation Spares Mice From Radiation-Induced Reductions in Weight Gain But Does Not Prevent Late Oligodendrocyte Lineage Side Effects

DOE Office of Scientific and Technical Information (OSTI.GOV)

Begolly, Sage; Shrager, Peter G.; Department of Pharmacology and Physiology, University of Rochester School of Medicine and Dentistry, Rochester, New York

Purpose: To determine the late effects of fractionated versus single-dose cranial radiation on murine white matter. Methods and Materials: Mice were exposed to 0 Gy, 6 × 6 Gy, or 1 × 20 Gy cranial irradiation at 10 to 12 weeks of age. Endpoints were assessed through 18 months from exposure using immunohistochemistry, electron microscopy, and electrophysiology. Results: Weight gain was temporarily reduced after irradiation; greater loss was seen after single versus fractionated doses. Oligodendrocyte progenitor cells were reduced early and late after both single and fractionated irradiation. Both protocols also increased myelin g-ratio, reduced the number of nodes of Ranvier, and promoted a shift in the proportion of small, unmyelinatedmore » versus large, myelinated axon fibers. Conclusions: Fractionation does not adequately spare normal white matter from late radiation side effects.« less

Wind turbine blade with viscoelastic damping

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sievers, Ryan A.; Mullings, Justin L.

A wind turbine blade (60) damped by viscoelastic material (54, 54A-F) sandwiched between stiffer load-bearing sublayers (52A, 52B, 56A, 56B) in portions of the blade effective to damp oscillations (38) of the blade. The viscoelastic material may be located in one or more of: a forward portion (54A) of the shell, an aft portion (54D) of the shell, pressure and suction side end caps (54B) of an internal spar, internal webbing walls (54C, 54E), and a trailing edge core (54F).

Surface Modification of the LiFePO4 Cathode for the Aqueous Rechargeable Lithium Ion Battery.

PubMed

Tron, Artur; Jo, Yong Nam; Oh, Si Hyoung; Park, Yeong Don; Mun, Junyoung

2017-04-12

The LiFePO 4 surface is coated with AlF 3 via a simple chemical precipitation for aqueous rechargeable lithium ion batteries (ARLBs). During electrochemical cycling, the unfavorable side reactions between LiFePO 4 and the aqueous electrolyte (1 M Li 2 SO 4 in water) leave a highly resistant passivation film, which causes a deterioration in the electrochemical performance. The coated LiFePO 4 by 1 wt % AlF 3 has a high discharge capacity of 132 mAh g -1 and a highly improved cycle life, which shows 93% capacity retention even after 100 cycles, whereas the pristine LiFePO 4 has a specific capacity of 123 mAh g -1 and a poor capacity retention of 82%. The surface analysis results, which include X-ray photoelectron spectroscopy and transmission electron microscopy results, show that the AlF 3 coating material is highly effective for reducing the detrimental surface passivation by relieving the electrochemical side reactions of the fragile aqueous electrolyte. The AlF 3 coating material has good compatibility with the LiFePO 4 cathode material, which mitigates the surface diffusion obstacles, reduces the charge-transfer resistances and improves the electrochemical performance and surface stability of the LiFePO 4 material in aqueous electrolyte solutions.

49 CFR 572.190 - Incorporated materials.

Code of Federal Regulations, 2012 CFR

2012-10-01

... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) ANTHROPOMORPHIC TEST DEVICES IIsD Side Impact Crash Test... procedures manual entitled, “Procedures for Assembly, Disassembly, and Inspection (PADI) of the SID-IIsD Side...

49 CFR 572.190 - Incorporated materials.

Code of Federal Regulations, 2014 CFR

2014-10-01

... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) ANTHROPOMORPHIC TEST DEVICES SID-IIsD Side Impact Crash... procedures manual entitled, “Procedures for Assembly, Disassembly, and Inspection (PADI) of the SID-IIsD Side...

49 CFR 572.180 - Incorporated materials.

Code of Federal Regulations, 2013 CFR

2013-10-01

... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) ANTHROPOMORPHIC TEST DEVICES ES-2re Side Impact Crash... 50th Percentile Adult Male Side Impact Crash Test Dummy, February 2008,” incorporated by reference in...

49 CFR 572.180 - Incorporated materials.

Code of Federal Regulations, 2012 CFR

2012-10-01

... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) ANTHROPOMORPHIC TEST DEVICES 2re Side Impact Crash Test... 50th Percentile Adult Male Side Impact Crash Test Dummy, February 2008,” incorporated by reference in...

49 CFR 572.180 - Incorporated materials.

Code of Federal Regulations, 2014 CFR

2014-10-01

... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) ANTHROPOMORPHIC TEST DEVICES ES-2re Side Impact Crash... 50th Percentile Adult Male Side Impact Crash Test Dummy, February 2008,” incorporated by reference in...

49 CFR 572.190 - Incorporated materials.

Code of Federal Regulations, 2013 CFR

2013-10-01

... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) ANTHROPOMORPHIC TEST DEVICES SID-IIsD Side Impact Crash... procedures manual entitled, “Procedures for Assembly, Disassembly, and Inspection (PADI) of the SID-IIsD Side...

Skin protection efficacy from UV irradiation and skin penetration property of polysaccharide-benzophenone conjugates as a sunscreen agent.

PubMed

Heo, Sukyoung; Hwang, Hee Sook; Jeong, Yohan; Na, Kun

2018-09-01

Sunscreen materials have been developed to protect skin from UV radiation. However, many organic sunscreen materials are small molecules and absorbed into human skin after topical application and lead to systemic side effects. To improve the adverse effects of conventional sunscreen materials, we designed a sunscreen agent using an organic sunscreen material and a polymer. Dioxybenzone, an organic sunscreen compound is selected and polymerized with natural polymer pullulan. Polymerization not only provides a long polymer backbone to dioxybenzone, but also keeps the distance between benzene rings of the dioxybenzone and prevents reduction of photoabsorption intensity. UV/vis spectrophotometry confirmed that dioxybenzone-pullulan polymer (DOB-PUL) and dioxybenzone (DOB) demonstrated similar UV absorption. To measure the accumulation of sunscreen materials on skin, Franz diffusion cell was used to confirm the accumulation of DOB and lack of penetration of DOB-PUL. Most importantly, DOB showed higher plasma concentration after multiple applications compared to that of DOB-PUL. Copyright © 2018 Elsevier Ltd. All rights reserved.

Stress distributions in maxillary central incisors restored with various types of post materials and designs.

PubMed

Madfa, A A; Kadir, M R Abdul; Kashani, J; Saidin, S; Sulaiman, E; Marhazlinda, J; Rahbari, R; Abdullah, B J J; Abdullah, H; Abu Kasim, N H

2014-07-01

Different dental post designs and materials affect the stability of restoration of a tooth. This study aimed to analyse and compare the stability of two shapes of dental posts (parallel-sided and tapered) made of five different materials (titanium, zirconia, carbon fibre and glass fibre) by investigating their stress transfer through the finite element (FE) method. Ten three-dimensional (3D) FE models of a maxillary central incisor restored with two different designs and five different materials were constructed. An oblique loading of 100 N was applied to each 3D model. Analyses along the centre of the post, the crown-cement/core and the post-cement/dentine interfaces were computed, and the means were calculated. One-way ANOVAs followed by post hoc tests were used to evaluate the effectiveness of the post materials and designs (p=0.05). For post designs, the tapered posts introduced significantly higher stress compared with the parallel-sided post (p<0.05), especially along the centre of the post. Of the materials, the highest level of stress was found for stainless steel, followed by zirconia, titanium, glass fibre and carbon fibre posts (p<0.05). The carbon and glass fibre posts reduced the stress distribution at the middle and apical part of the posts compared with the stainless steel, zirconia and titanium posts. The opposite results were observed at the crown-cement/core interface. Copyright © 2014 IPEM. Published by Elsevier Ltd. All rights reserved.

Method of Fabricating a Composite Apparatus

NASA Technical Reports Server (NTRS)

Wilkie, W. Keats (Inventor); Bryant, Robert G. (Inventor); Fox, Robert L. (Inventor); Hellbaum, Richard F. (Inventor); High, James W. (Inventor); Jalink, Antony, Jr. (Inventor)

2007-01-01

A method for fabricating a piezoelectric macro-fiber composite actuator comprises making a piezoelectric fiber sheet by providing a plurality of wafers of piezoelectric material, bonding the wafers together with an adhesive material to from a stack of alternating layers of piezoelectric material and adhesive material, and cutting through the stack in a direction substantially parallel to the thickness of the stack and across the alternating layers of piezoelectric material and adhesive material to provide at least one piezoelectric fiber sheet having two sides comprising a plurality of piezoelectric fibers in juxtaposition to the adhesive material. The method further comprises bonding two electrically conductive films to the two sides of the piezoelectric fiber sheet. At least one conductive film has first and second conductive patterns formed thereon which are electrically isolated from one another and in electrical contact with the piezoelectric fiber sheet.

Low dose mTHPC photodynamic therapy for cholangiocarcinoma

NASA Astrophysics Data System (ADS)

Stepp, Herbert; Kniebühler, Gesa; Pongratz, Thomas; Betz, Christian S.; Göke, Burkhard; Sroka, Ronald; Schirra, Jörg

2013-06-01

Objective: Demonstration of whether a low dose of mTHPC (temoporfin , Foscan) is sufficient to induce an efficient clinical response in palliative PDT of non-resectable cholangiocarcinoma (CC), while showing a low side effect profile as compared to the standard Photofrin PDT. Materials and Methods: 13 patients (14 treatment sessions) with non-resectable CC were treated with stenting and PDT (3 mg Foscan per treatment, 0.032-0.063 mg/kg body weight, 652 nm, 50 J/cm). Fluorescence measurements were performed with a single bare fiber for 5/13 patients prior to PDT at the tumor site to determine the fluorescence contrast. For another 7/13 patients, long-term fluorescence-kinetics were measured on the oral mucosa to determine the time of maximal relative fluorescence intensity. Results: Foscan fluorescence could clearly be identified spectroscopically as early as 20 hours after administration. It was not significantly different between lesion and normal tissue within the bile duct. Fluorescence kinetics assessed at the oral mucosa were highest at 72-96 hours after administration. The DLI was therefore extended from 20 hours to approx. 70 hours for the last 5 patients treated. The treatment effect was promising with a median survival of 11 months for the higher grade tumors (Bismuth types III and IV). Local side effects occurred in one patient (pancreatitis), systemic side effects were much reduced compared to prior experience with Photofrin. Conclusion: Combined stenting and photodynamic therapy (PDT) performed with a low dose of Foscan results in comparable survival times relative to standard Photofrin PDT, while lowering the risk of side effects significantly.

Alternative Fluoropolymers to Avoid the Challenges Associated with Perfluorooctanoic Acid

DOE Office of Scientific and Technical Information (OSTI.GOV)

Guo,J.; Resnick, P.; Efimenko, K.

2008-01-01

The degradation of stain-resistant coating materials leads to the release of biopersistent perfluorooctanoic acid (PFOA) to the environment. In order to find the environmentally friendly substitutes, we have designed and synthesized a series of nonbiopersistant fluorinated polymers containing perfluorobutyl groups in the side chains. The surface properties of the new coating materials were characterized by static and dynamic contact angle measurements. The new coating materials demonstrate promising hydrophobic and oleophobic properties with low surfaces tensions. The wetting properties and surface structure of the polymers were tuned by varying the 'spacer' structures between the polymer backbones and the perfluorinated groups ofmore » the side chains. The relationship between orientations of the fluorinated side chains and performances of polymer surfaces were further investigated by near-edge X-ray fine absorption structure (NEXAFS) experiments and differential scanning calorimetry (DSC).« less

Mouse repeated electroconvulsive seizure (ECS) does not reverse social stress effects but does induce behavioral and hippocampal changes relevant to electroconvulsive therapy (ECT) side-effects in the treatment of depression

PubMed Central

Sigrist, Hannes; Seifritz, Erich; Fikse, Lianne; Bosker, Fokko J.; Schoevers, Robert A.; Klein, Hans C.

2017-01-01

Electroconvulsive therapy (ECT) is an effective treatment for depression, but can have negative side effects including amnesia. The mechanisms of action underlying both the antidepressant and side effects of ECT are not well understood. An equivalent manipulation that is conducted in experimental animals is electroconvulsive seizure (ECS). Rodent studies have provided valuable insights into potential mechanisms underlying the antidepressant and side effects of ECT. However, relatively few studies have investigated the effects of ECS in animal models with a depression-relevant manipulation such as chronic stress. In the present study, mice were first exposed to chronic social stress (CSS) or a control procedure for 15 days followed by ECS or a sham procedure for 10 days. Behavioral effects were investigated using an auditory fear conditioning (learning) and expression (memory) test and a treadmill-running fatigue test. Thereafter, immunohistochemistry was conducted on brain material using the microglial marker Iba-1 and the cholinergic fibre marker ChAT. CSS did not increase fear learning and memory in the present experimental design; in both the control and CSS mice ECS reduced fear learning and fear memory expression. CSS induced the expected fatigue-like effect in the treadmill-running test; ECS induced increased fatigue in CSS and control mice. In CSS and control mice ECS induced inflammation in hippocampus in terms of increased expression of Iba-1 in radiatum of CA1 and CA3. CSS and ECS both reduced acetylcholine function in hippocampus as indicated by decreased expression of ChAT in several hippocampal sub-regions. Therefore, CSS increased fatigue and reduced hippocampal ChAT activity and, rather than reversing these effects, a repeated ECS regimen resulted in impaired fear learning-memory, increased fatigue, increased hippocampal Iba-1 expression, and decreased hippocampal ChAT expression. As such, the current model does not provide insights into the mechanism of ECT antidepressant function but does provide evidence for pathophysiological mechanisms that might contribute to important ECT side-effects. PMID:28910337

Mouse repeated electroconvulsive seizure (ECS) does not reverse social stress effects but does induce behavioral and hippocampal changes relevant to electroconvulsive therapy (ECT) side-effects in the treatment of depression.

PubMed

van Buel, Erin M; Sigrist, Hannes; Seifritz, Erich; Fikse, Lianne; Bosker, Fokko J; Schoevers, Robert A; Klein, Hans C; Pryce, Christopher R; Eisel, Ulrich Lm

2017-01-01

Electroconvulsive therapy (ECT) is an effective treatment for depression, but can have negative side effects including amnesia. The mechanisms of action underlying both the antidepressant and side effects of ECT are not well understood. An equivalent manipulation that is conducted in experimental animals is electroconvulsive seizure (ECS). Rodent studies have provided valuable insights into potential mechanisms underlying the antidepressant and side effects of ECT. However, relatively few studies have investigated the effects of ECS in animal models with a depression-relevant manipulation such as chronic stress. In the present study, mice were first exposed to chronic social stress (CSS) or a control procedure for 15 days followed by ECS or a sham procedure for 10 days. Behavioral effects were investigated using an auditory fear conditioning (learning) and expression (memory) test and a treadmill-running fatigue test. Thereafter, immunohistochemistry was conducted on brain material using the microglial marker Iba-1 and the cholinergic fibre marker ChAT. CSS did not increase fear learning and memory in the present experimental design; in both the control and CSS mice ECS reduced fear learning and fear memory expression. CSS induced the expected fatigue-like effect in the treadmill-running test; ECS induced increased fatigue in CSS and control mice. In CSS and control mice ECS induced inflammation in hippocampus in terms of increased expression of Iba-1 in radiatum of CA1 and CA3. CSS and ECS both reduced acetylcholine function in hippocampus as indicated by decreased expression of ChAT in several hippocampal sub-regions. Therefore, CSS increased fatigue and reduced hippocampal ChAT activity and, rather than reversing these effects, a repeated ECS regimen resulted in impaired fear learning-memory, increased fatigue, increased hippocampal Iba-1 expression, and decreased hippocampal ChAT expression. As such, the current model does not provide insights into the mechanism of ECT antidepressant function but does provide evidence for pathophysiological mechanisms that might contribute to important ECT side-effects.

Method of fabricating bifacial tandem solar cells

DOEpatents

Wojtczuk, Steven J; Chiu, Philip T; Zhang, Xuebing; Gagnon, Edward; Timmons, Michael

2014-10-07

A method of fabricating on a semiconductor substrate bifacial tandem solar cells with semiconductor subcells having a lower bandgap than the substrate bandgap on one side of the substrate and with subcells having a higher bandgap than the substrate on the other including, first, growing a lower bandgap subcell on one substrate side that uses only the same periodic table group V material in the dislocation-reducing grading layers and bottom subcells as is present in the substrate and after the initial growth is complete and then flipping the substrate and growing the higher bandgap subcells on the opposite substrate side which can be of different group V material.

Bifacial tandem solar cells

DOEpatents

Wojtczuk, Steven J.; Chiu, Philip T.; Zhang, Xuebing; Gagnon, Edward; Timmons, Michael

2016-06-14

A method of fabricating on a semiconductor substrate bifacial tandem solar cells with semiconductor subcells having a lower bandgap than the substrate bandgap on one side of the substrate and with subcells having a higher bandgap than the substrate on the other including, first, growing a lower bandgap subcell on one substrate side that uses only the same periodic table group V material in the dislocation-reducing grading layers and bottom subcells as is present in the substrate and after the initial growth is complete and then flipping the substrate and growing the higher bandgap subcells on the opposite substrate side which can be of different group V material.

Weld repair method for aluminum lithium seam

NASA Technical Reports Server (NTRS)

McGee, William Floyd (Inventor); Rybicki, Daniel John (Inventor)

1998-01-01

Aluminum-lithium plates are butt-welded by juxtaposing the plates and making a preliminary weld from the rear or root side of the seam. An initial weld is then made from the face side of the seam, which may cause a defect in the root portion. A full-size X-ray is made and overlain over the seam to identify the defects. The defect is removed from the root side, and rewelded. Material is then removed from the face side, and the cavity is rewelded. The procedure repeats, alternating from the root side to the face side, until the weld is sound.

Near-infrared light-responsive nanomaterials in cancer therapeutics.

PubMed

Shanmugam, Vijayakumar; Selvakumar, S; Yeh, Chen-Sheng

2014-09-07

Noninvasive techniques, such as breath tests (urea breath test), blood pressure measurements using a sphygmomanometer and electrocardiography, were employed by a physician to perform classical diagnosis. The use of state-of-the-art noninvasive therapies at the organ level in modern medicine has gradually become possible. However, cancer treatment demands spatially and temporally controlled noninvasive therapy at the cell level because nonspecific toxicity often causes complicated side effects. To increase survival in cancer patients further, combination therapy and combination drugs are explored which demand high specificity to avoid combined-drug side effects. We believe that high specificity could be obtained by implementing near-infrared (NIR) light-assisted nanoparticles in photothermal therapy, chemotherapy, and photodynamic therapy. To refine this therapy and subsequently achieve high efficiency, novel nanomaterials have been designed and modified either to enhance the uptake and drug delivery to the cancer site, or control treatment to administer therapy efficiently. These modifications and developments have been demonstrated to achieve spatial and temporal control when conducting an in vivo xenograft, because the NIR light penetrated effectively the biological tissue. The nanoplatforms discussed in this review are grouped under the following subheadings: Au nanorods (NRs), Au nanoshells, other Au-related nanomaterials, graphene oxide, upconversion nanoparticles, and other related materials (including materials such as CuS, Fe3O4-related systems, and carbon nanotubes (CNTs)).

The mental cost of cognitive enhancement.

PubMed

Iuculano, Teresa; Cohen Kadosh, Roi

2013-03-06

Noninvasive brain stimulation provides a potential tool for affecting brain functions in the typical and atypical brain and offers in several cases an alternative to pharmaceutical intervention. Some studies have suggested that transcranial electrical stimulation (TES), a form of noninvasive brain stimulation, can also be used to enhance cognitive performance. Critically, research so far has primarily focused on optimizing protocols for effective stimulation, or assessing potential physical side effects of TES while neglecting the possibility of cognitive side effects. We assessed this possibility by targeting the high-level cognitive abilities of learning and automaticity in the mathematical domain. Notably, learning and automaticity represent critical abilities for potential cognitive enhancement in typical and atypical populations. Over 6 d, healthy human adults underwent cognitive training on a new numerical notation while receiving TES to the posterior parietal cortex or the dorsolateral prefrontal cortex. Stimulation to the the posterior parietal cortex facilitated numerical learning, whereas automaticity for the learned material was impaired. In contrast, stimulation to the dorsolateral prefrontal cortex impaired the learning process, whereas automaticity for the learned material was enhanced. The observed double dissociation indicates that cognitive enhancement through TES can occur at the expense of other cognitive functions. These findings have important implications for the future use of enhancement technologies for neurointervention and performance improvement in healthy populations.

47 CFR 1.49 - Specifications as to pleadings and documents.

Code of Federal Regulations, 2010 CFR

2010-10-01

....7 cm.) or on 81/2 × 11 inch (21.6 cm. × 27.9 cm.) paper with the margins set so that the printed material does not exceed 6 1/2 × 91/2 inches (16.5 cm. × 24.1 cm.). The printed material may be in any... form. Pleadings may be printed on both sides of the paper. Pleadings that use only one side of the...

Teaching Materials to Enhance the Visual Expression of Web Pages for Students Not in Art or Design Majors

ERIC Educational Resources Information Center

Ariga, T.; Watanabe, T.

2008-01-01

The explosive growth of the Internet has made the knowledge and skills for creating Web pages into general subjects that all students should learn. It is now common to teach the technical side of the production of Web pages and many teaching materials have been developed. However teaching the aesthetic side of Web page design has been neglected,…

Monolayer group-III monochalcogenides by oxygen functionalization: a promising class of two-dimensional topological insulators

NASA Astrophysics Data System (ADS)

Zhou, Si; Liu, Cheng-Cheng; Zhao, Jijun; Yao, Yugui

2018-03-01

Monolayer group-III monochalcogenides (MX, M = Ga, In; X = S, Se, Te), an emerging category of two-dimensional (2D) semiconductors, hold great promise for electronics, optoelectronics and catalysts. By first-principles calculations, we show that the phonon dispersion and Raman spectra, as well as the electronic and topological properties of monolayer MX can be tuned by oxygen functionalization. Chemisorption of oxygen atoms on one side or both sides of the MX sheet narrows or even closes the band gap, enlarges work function, and significantly reduces the carrier effective mass. More excitingly, InS, InSe, and InTe monolayers with double-side oxygen functionalization are 2D topological insulators with sizeable bulk gap up to 0.21 eV. Their low-energy bands near the Fermi level are dominated by the px and py orbitals of atoms, allowing band engineering via in-plane strains. Our studies provide viable strategy for realizing quantum spin Hall effect in monolayer group-III monochalcogenides at room temperature, and utilizing these novel 2D materials for high-speed and dissipationless transport devices.

Hydrofluoric acid-resistant composite window and method for its fabrication

DOEpatents

Ostenak, C.A.; Mackay, H.A.

1985-07-18

A hydrofluoric acid-resistant composite window and method for its fabrication are disclosed. The composite window comprises a window having first and second sides. The first side is oriented towards an environment containing hydrofluoric acid. An adhesive is applied to the first side. A layer of transparent hydrofluoric acid-resistant material, such as Mylar, is applied to the adhesive and completely covers the first side. The adhesive is then cured.

Hydrofluoric acid-resistant composite window and method for its fabrication

DOEpatents

Ostenak, Carl A.; Mackay, Harold A.

1987-01-01

A hydrofluoric acid-resistant composite window and method for its fabrication are disclosed. The composite window comprises a window having first and second sides. The first side is oriented towards an environment containing hydrofluoric acid. An adhesive is applied to the first side. A layer of transparent hydrofluoric acid-resistant material, such as Mylar, is applied to the adhesive and completely covers the first side. The adhesive is then cured.

Explosive bulk charge

DOEpatents

Miller, Jacob Lee

2015-04-21

An explosive bulk charge, including: a first contact surface configured to be selectively disposed substantially adjacent to a structure or material; a second end surface configured to selectively receive a detonator; and a curvilinear side surface joining the first contact surface and the second end surface. The first contact surface, the second end surface, and the curvilinear side surface form a bi-truncated hemispherical structure. The first contact surface, the second end surface, and the curvilinear side surface are formed from an explosive material. Optionally, the first contact surface and the second end surface each have a substantially circular shape. Optionally, the first contact surface and the second end surface consist of planar structures that are aligned substantially parallel or slightly tilted with respect to one another. The curvilinear side surface has one of a smooth curved geometry, an elliptical geometry, and a parabolic geometry.

Effect of overcharge on Li(Ni0.5Mn0.3Co0.2)O2/Graphite lithium ion cells with poly(vinylidene fluoride) binder. I - Microstructural changes in the anode

NASA Astrophysics Data System (ADS)

Dietz Rago, Nancy; Bareño, Javier; Li, Jianlin; Du, Zhijia; Wood, David L.; Steele, Leigh Anna; Lamb, Joshua; Spangler, Scott; Grosso, Christopher; Fenton, Kyle; Bloom, Ira

2018-05-01

Cells based on NMC/graphite, containing poly(vinylidene difluoride) (PVDF) binders in the positive and negative electrodes, were systematically overcharged to 100, 120, 140, 160, 180, and 250% state-of-charge (SOC). At 250% SOC the cell vented. Scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) of the anodes showed several state-of-overcharge-dependent trends. Starting at 120% SOC, dendrites appeared and increased in concentration as the SOC increased. Dendrite morphology appeared to be dependent on whether the active material was on the "dull" or "shiny" side of the copper collector. Significantly more delamination of the active material from the collector was seen on the "shiny" side of the collector particularly at 180 and 250% SOC. Transition metals were detected at 120% SOC and increased in concentration as the SOC increased. There was considerable spatial heterogeneity in the microstructures across each laminate with several regions displaying complex layered structures.

Children's Literature-Comparatively Reading. Thinking about the Pink Bits: A Consideration of the Influence of English Children's Literature.

ERIC Educational Resources Information Center

Webb, Jean

This paper examines the state of children's literature by tracing some of the side effects of nineteenth-century English children's literature. During their early histories, the British colonies, including America, were economically unable to produce their own children's books. Reading materials were imported from the home country, and, likewise,…

Compositional mapping of Saturn's satellite Dione with Cassini VIMS and implications of dark material in the Saturn system

USGS Publications Warehouse

Clark, R.N.; Curchin, J.M.; Jaumann, R.; Cruikshank, D.P.; Brown, R.H.; Hoefen, T.M.; Stephan, K.; Moore, Johnnie N.; Buratti, B.J.; Baines, K.H.; Nicholson, P.D.; Nelson, R.M.

2008-01-01

Cassini VIMS has obtained spatially resolved imaging spectroscopy data on numerous satellites of Saturn. A very close fly-by of Dione provided key information for solving the riddle of the origin of the dark material in the Saturn system. The Dione VIMS data show a pattern of bombardment of fine, sub-0.5-??m diameter particles impacting the satellite from the trailing side direction. Multiple lines of evidence point to an external origin for the dark material on Dione, including the global spatial pattern of dark material, local patterns including crater and cliff walls shielding implantation on slopes facing away from the trailing side, exposing clean ice, and slopes facing the trailing direction which show higher abundances of dark material. Multiple spectral features of the dark material match those seen on Phoebe, Iapetus, Hyperion, Epimetheus and the F-ring, implying the material has a common composition throughout the Saturn system. However, the exact composition of the dark material remains a mystery, except that bound water and, tentatively, ammonia are detected, and there is evidence both for and against cyanide compounds. Exact identification of composition requires additional laboratory work. A blue scattering peak with a strong UV-visible absorption is observed in spectra of all satellites which contain dark material, and the cause is Rayleigh scattering, again pointing to a common origin. The Rayleigh scattering effect is confirmed with laboratory experiments using ice and 0.2-??m diameter carbon grains when the carbon abundance is less than about 2% by weight. Rayleigh scattering in solids is also confirmed in naturally occurring terrestrial rocks, and in previously published reflectance studies. The spatial pattern, Rayleigh scattering effect, and spectral properties argue that the dark material is only a thin coating on Dione's surface, and by extension is only a thin coating on Phoebe, Hyperion, and Iapetus, although the dark material abundance appears higher on Iapetus, and may be locally thick. As previously concluded for Phoebe, the dark material appears to be external to the Saturn system and may be cometary in origin. We also report a possible detection of material around Dione which may indicate Dione is active and contributes material to the E-ring, but this observation must be confirmed.

A One-Year Evaluation of a Free Fissure Sealant Program.

PubMed

M, Bakhtiar; N, Azadi; A, Golkari

2016-12-01

Pit and fissure sealant therapy has been approved as an effective measure in the prevention of occlusal dental caries. Resin based materials are the most common materials used worldwide. A variety of resin based fissure sealants are produced and used. Most of them have been presented with ideal results in research environment. However, their effectiveness in the real life, especially in a mass application program such as Iran's oral health reform plan is not clear. To evaluate the longevity of different fissure sealant applied in Iran's oral health reform plan in Fars Province (south of Iran) after one year. Seven counties were selected. One hundred 6- to 8-year-old school children who had undergone fissure sealant therapy in spring 2015 were randomly selected from each county. Their first molars were examined to evaluate the status of the fissure sealants which were applied one year ago. Data on the type/brand of fissure sealant materials, type and experience of clinicians who applied them, existence of a chair-side assistant, and whether the children were caries-free at the time of fissure sealant application were collected from the existing reports. Data of 1974 teeth from 598 children were used for the final analysis. The effects of type/brand of the material was significant on the final results and remained significant ( p < 0.001) after adjustments for the level of fluoride, urban/rural area, upper/lower jaw, type of clinician who applied the sealant, existence of a chair-side assistant, and child's gender, age, and being caries-free. Many factors affect the success rate of a fissure sealant therapy program. The type/brand of the material remained significantly related to the success rate of the fissure sealant even after adjustments for other influencing factors. In this study, ClinproTM Sealant (3M/ESPE, USA) showed better longevity after one year of application.

Comparison of the in vitro Effect of Chemical and Herbal Mouthwashes on Candida albicans

PubMed Central

Talebi, Somayeh; Sabokbar, Azar; Riazipour, Majid; Saffari, Mohsen

2014-01-01

Background: During the recent decades research has focused to find scientific evidence for the effects of herbal medicines. Researchers are interested in herbal remedies for medication and aim to substitute herbal material instead of chemical formula with limited side effects for human being. Objectives: The aim of the current study was to compare the in vitro effect of herbal and chemical mouthwashes against Candida albicans. Materials and Methods: In this research, we used a standard strain of C. albicans, PTCC 5027. The suspension was made by a fresh culture of C. albicans (24 hours) and the optical density (turbidity equating to a McFarland standard of 0.5) was read at 530 nm. The C. albicans suspension was cultured on Sabouraud dextrose agar plate. Next, two wells were filled with mouthwashes and after incubation at 30ºC for 24 hours, the inhibition zone was measured. Minimum inhibitory concentration (MIC) and minimum fungicidal concentration (MFC) of mouthwashes were determined. Data were analyzed using the SPSS software, independent T-tests and one-sided variance analysis (ANOVA-one way). Results: Based on these findings on agar diffusion with (P = 0.764), MIC and MFC tests (P = 0.879), there were no significant differences between the antifungal effect of herbal and chemical mouthwashes. Conclusions: This study showed that, chemical mouthwashes acted better than herbal mouthwashes and among different chemical mouthwashes, Oral B was most effective. PMID:25741429

Remote Sensing of Aquatic Plants.

DTIC Science & Technology

1979-10-01

remote sensing methods for identification and assessment of expanses of aquatic plants. Both materials and techniques are examined for cost effectiveness and capability to sense aquatic plants on both the local and regional scales. Computer simulation of photographic responses was employed; Landsat, high-altitude photography, side-looking airborne radar, and low-altitude photography were examined to determine the capabilities of each for identifying and assessing aquatic plants. Results of the study revealed Landsat to be the most cost effective for regional surveys,

Significant Effect of Pore Sizes on Energy Storage in Nanoporous Carbon Supercapacitors.

PubMed

Young, Christine; Lin, Jianjian; Wang, Jie; Ding, Bing; Zhang, Xiaogang; Alshehri, Saad M; Ahamad, Tansir; Salunkhe, Rahul R; Hossain, Shahriar A; Khan, Junayet Hossain; Ide, Yusuke; Kim, Jeonghun; Henzie, Joel; Wu, Kevin C-W; Kobayashi, Naoya; Yamauchi, Yusuke

2018-04-20

Mesoporous carbon can be synthesized with good control of surface area, pore-size distribution, and porous architecture. Although the relationship between porosity and supercapacitor performance is well known, there are no thorough reports that compare the performance of numerous types of carbon samples side by side. In this manuscript, we describe the performance of 13 porous carbon samples in supercapacitor devices. We suggest that there is a "critical pore size" at which guest molecules can pass through the pores effectively. In this context, the specific surface area (SSA) and pore-size distribution (PSD) are used to show the point at which the pore size crosses the threshold of critical size. These measurements provide a guide for the development of new kinds of carbon materials for supercapacitor devices. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Imitations and Transformations: On Side Effects of the ADHD Epidemic.

PubMed

Nielsen, Bjarke

2017-04-01

The attention deficit hyperactivity disorder epidemic has been the subject of much scrutiny, especially in relation to the medicalization of children, and, to a lesser degree, to the use of Ritalin as a performance enhancer or party drug (e.g., Keane 2008; Whitaker 2010; Bowden 2013). In this article, my focus is on non-investigated side effects of this epidemic, namely the use of (prescription) Ritalin among heavy drug users. Based on fieldwork conducted in one of the largest cities in Denmark, in this article I trace the spread of intravenous use of Ritalin, and examine how different ways of ingesting Ritalin transform the drug itself, and, with this, transform treatment practices, parts of the drug scene, and the bodies of users. In my analysis, I draw on insights from anthropological theories on imitation and from material semiotics.

Efficient p-n junction-based thermoelectric generator that can operate at extreme temperature conditions

NASA Astrophysics Data System (ADS)

Chavez, Ruben; Angst, Sebastian; Hall, Joseph; Maculewicz, Franziska; Stoetzel, Julia; Wiggers, Hartmut; Thanh Hung, Le; Van Nong, Ngo; Pryds, Nini; Span, Gerhard; Wolf, Dietrich E.; Schmechel, Roland; Schierning, Gabi

2018-01-01

In many industrial processes, a large proportion of energy is lost in the form of heat. Thermoelectric generators can convert this waste heat into electricity by means of the Seebeck effect. However, the use of thermoelectric generators in practical applications on an industrial scale is limited in part because electrical, thermal, and mechanical bonding contacts between the semiconductor materials and the metal electrodes in current designs are not capable of withstanding thermal-mechanical stress and alloying of the metal-semiconductor interface when exposed to the high temperatures occurring in many real-world applications. Here we demonstrate a concept for thermoelectric generators that can address this issue by replacing the metallization and electrode bonding on the hot side of the device by a p-n junction between the two semiconductor materials, making the device robust against temperature induced failure. In our proof-of-principle demonstration, a p-n junction device made from nanocrystalline silicon is at least comparable in its efficiency and power output to conventional devices of the same material and fabrication process, but with the advantage of sustaining high hot side temperatures and oxidative atmosphere.

No blank slates: Pre-existing schemas about pharmaceuticals predict memory for side effects.

PubMed

Heller, Monika K; Chapman, Sarah C E; Horne, Rob

2017-04-01

Attribution of symptoms as medication side effects is informed by pre-existing beliefs about medicines and perceptions of personal sensitivity to their effects (pharmaceutical schemas). We tested whether (1) pharmaceutical schemas were associated with memory (recall/recognition) for side effect information (2) memory explained the attribution of a common unrelated symptom as a side effect. In this analogue study participants saw the patient leaflet of a fictitious asthma drug listing eight side effects. We measured recall and recognition memory for side effects and used a vignette to test whether participants attributed an unlisted common symptom (headache) as a side effect. Participants who perceived pharmaceuticals as more harmful in general recalled fewer side effects correctly (r Correct Recall  = -.273), were less able to differentiate between listed and unlisted side effects (r Recognition Sensitivity  = -.256) and were more likely to attribute the unlisted headache symptom as a side effect (r side effect attribution  = .381, ps < .01). The effect of harm beliefs on side effect attribution was partially mediated by correct recall of side effects. Pharmaceutical schemas are associated with memory for side effect information. Memory may explain part of the association between pharmaceutical schemas and the attribution of unrelated symptoms as side effects.

Cardiovascular cast model fabrication and casting effectiveness evaluation in fetus with severe congenital heart disease or normal heart.

PubMed

Wang, Yu; Cao, Hai-yan; Xie, Ming-xing; He, Lin; Han, Wei; Hong, Liu; Peng, Yuan; Hu, Yun-fei; Song, Ben-cai; Wang, Jing; Wang, Bin; Deng, Cheng

2016-04-01

To investigate the application and effectiveness of vascular corrosion technique in preparing fetal cardiovascular cast models, 10 normal fetal heart specimens with other congenital disease (control group) and 18 specimens with severe congenital heart disease (case group) from induced abortions were enrolled in this study from March 2013 to June 2015 in our hospital. Cast models were prepared by injecting casting material into vascular lumen to demonstrate real geometries of fetal cardiovascular system. Casting effectiveness was analyzed in terms of local anatomic structures and different anatomical levels (including overall level, atrioventricular and great vascular system, left-sided and right-sided heart), as well as different trimesters of pregnancy. In our study, all specimens were successfully casted. Casting effectiveness analysis of local anatomic structures showed a mean score from 1.90±1.45 to 3.60±0.52, without significant differences between case and control groups in most local anatomic structures except left ventricle, which had a higher score in control group (P=0.027). Inter-group comparison of casting effectiveness in different anatomical levels showed no significant differences between the two groups. Intra-group comparison also revealed undifferentiated casting effectiveness between atrioventricular and great vascular system, or left-sided and right-sided heart in corresponding group. Third-trimester group had a significantly higher perfusion score in great vascular system than second-trimester group (P=0.046), while the other anatomical levels displayed no such difference. Vascular corrosion technique can be successfully used in fabrication of fetal cardiovascular cast model. It is also a reliable method to demonstrate three-dimensional anatomy of severe congenital heart disease and normal heart in fetus.

Acicular photomultiplier photocathode structure

DOEpatents

Craig, Richard A.; Bliss, Mary

2003-09-30

A method and apparatus for increasing the quantum efficiency of a photomultiplier tube by providing a photocathode with an increased surface-to-volume ratio. The photocathode includes a transparent substrate, upon one major side of which is formed one or more large aspect-ratio structures, such as needles, cones, fibers, prisms, or pyramids. The large aspect-ratio structures are at least partially composed of a photoelectron emitting material, i.e., a material that emits a photoelectron upon absorption of an optical photon. The large aspect-ratio structures may be substantially composed of the photoelectron emitting material (i.e., formed as such upon the surface of a relatively flat substrate) or be only partially composed of a photoelectron emitting material (i.e., the photoelectron emitting material is coated over large aspect-ratio structures formed from the substrate material itself.) The large aspect-ratio nature of the photocathode surface allows for an effective increase in the thickness of the photocathode relative the absorption of optical photons, thereby increasing the absorption rate of incident photons, without substantially increasing the effective thickness of the photocathode relative the escape incidence of the photoelectrons.

Evaluation of anti-plaque microbial activity of Azadirachta indica (neem oil) in vitro: A pilot study

PubMed Central

Elavarasu, Sugumari; Abinaya, P.; Elanchezhiyan, S.; Thangakumaran; Vennila, K.; Naziya, K. B.

2012-01-01

Background: Probably microbial plaque is the main etiology for periodontal tissue inflammation. Various chemical agents have been evaluated over the years with respect to their antimicrobial effects in the oral cavity. However, all are associated with side effects that prohibit regular long-term use. Therefore, the effectiveness of Azadirachta indica (neem) against plaque formation is considered to be vital, with lesser side effects. The aim of the present study is to evaluate and prove the antimicrobial activity of neem using plaque samples. Materials and Methods: Culture was prepared using brain heart infusion broth reagent. Dental plaque samples were used for that. Kirby–Bauer antimicrobial susceptibility test procedure was carried away with the sample. Neem oil was kept in the agar plate with culture and the diameter of inhibition zones was calculated. Results: Results showed inhibition zones on the agar plate around neem oil. Conclusion: Study shows definite antiplaque activity of neem oil. PMID:23066297

Effects of simulated space environment on Skylab parasol material

NASA Technical Reports Server (NTRS)

Slemp, W. S.

1974-01-01

A material consisting of ripstop nylon bonded to the Mylar side of aluminized Mylar film was used to construct the first Skylab parasol. The mechanical properties of elongation and tensile strength and the radiative properties of solar absorptance and thermal emittance were measured before and after exposure to simulated solar radiation at intensities of 1.0 and 3.5 solar constants for exposure times as long as 947 hours or 3316 equivalent solar hours. The accelerated testing indicated more severe degradation than was experienced in the real-time test (1 solar constant). The results predicted that this material could have given satisfactory performance throughout the planned lifetime of the Skylab workshop.

Hybrid Fiber Layup and Fiber-Reinforced Polymeric Composites Produced Therefrom

NASA Technical Reports Server (NTRS)

Barnell, Thomas J. (Inventor); Garrigan, Sean P. (Inventor); Rauscher, Michael D. (Inventor); Dietsch, Benjamin A. (Inventor); Cupp, Gary N. (Inventor)

2018-01-01

Embodiments of a hybrid fiber layup used to form a fiber-reinforced polymeric composite, and a fiber-reinforced polymeric composite produced therefrom are disclosed. The hybrid fiber layup comprises one or more dry fiber strips and one or more prepreg fiber strips arranged side by side within each layer, wherein the prepreg fiber strips comprise fiber material impregnated with polymer resin and the dry fiber strips comprise fiber material without impregnated polymer resin.

Decoding the Domino: The Dark Side of Iapetus

NASA Technical Reports Server (NTRS)

Owen, Tobias C.; Cruikshank, Dale P.; DalleOre, C. M.; Geballe, T. R.; Roush, T. L.; deBergh, C.; Meier, Roland; Pendleton, Yvonne J.; Khare, Bishun N.; DeVincenzi, D. (Technical Monitor)

2001-01-01

We present new spectra of the leading and trailing hemispheres of Iapetus from 2.4 to 3.8 micron. We have combined the leading hemisphere spectra with previous observations by others to construct a composite spectrum of the dark side (leading) hemisphere from 0.3 to 3.8 gm. We review attempts to deduce the composition of the dark material from previously available spectrophotometry. None of them (numbering more than 20 million!) leads to a synthetic spectrum that matches the new data. An intimate mixture of water ice, amorphous carbon and a nitrogen-rich organic compound (modeled here as Triton tholin) can fit the entire composite dark side spectrum. Observations in this spectral region have not revealed this mix of material on any other object observed thus far. We propose that this dark material may have originated on Titan, where atmospheric photochemistry has been producing nitrogen-rich organic compounds for 4.5 GY.

Method of bonding

DOEpatents

Saller, deceased, Henry A.; Hodge, Edwin S.; Paprocki, Stanley J.; Dayton, Russell W.

1987-12-01

1. A method of making a fuel-containing structure for nuclear reactors, comprising providing an assembly comprising a plurality of fuel units; each fuel unit consisting of a core plate containing thermal-neutron-fissionable material, sheets of cladding metal on its bottom and top surfaces, said cladding sheets being of greater width and length than said core plates whereby recesses are formed at the ends and sides of said core plate, and end pieces and first side pieces of cladding metal of the same thickness as the core plate positioned in said recesses, the assembly further comprising a plurality of second side pieces of cladding metal engaging the cladding sheets so as to space the fuel units from one another, and a plurality of filler plates of an acid-dissolvable nonresilient material whose melting point is above 2000.degree. F., each filler plate being arranged between a pair of said second side pieces and the cladding plates of two adjacent fuel units, the filler plates having the same thickness as the second side pieces; the method further comprising enclosing the entire assembly in an envelope; evacuating the interior of the entire assembly through said envelope; applying inert gas under a pressure of about 10,000 psi to the outside of said envelope while at the same time heating the assembly to a temperature above the flow point of the cladding metal but below the melting point of any material of the assembly, whereby the envelope is pressed against the assembly and integral bonds are formed between plates, sheets, first side pieces, and end pieces and between the sheets and the second side pieces; slowly cooling the assembly to room temperature; removing the envelope; and dissolving the filler plates without attacking the cladding metal.

ETR BUILDING, TRA642. SOUTH SIDE VIEW INCLUDES SOUTH SIDES OF ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

ETR BUILDING, TRA-642. SOUTH SIDE VIEW INCLUDES SOUTH SIDES OF ETR BUILDING (HIGH ROOF LINE); ELECTRICAL BUILDING (ONE-STORY, MADE OF PUMICE BLOCKS), TRA-648; AND HEAT EXCHANGER BUILDING (WITH BUILDING NUMBERS), TRA-644. NOTE PROJECTION OF ELECTRICAL BUILDING AT LEFT EDGE OF VIEW. CAMERA FACES NORTH. INL NEGATIVE NO. HD46-37-3. Mike Crane, Photographer, 4/2005 - Idaho National Engineering Laboratory, Test Reactor Area, Materials & Engineering Test Reactors, Scoville, Butte County, ID

DOE Office of Scientific and Technical Information (OSTI.GOV)

Madin, Mark Michael; Wicks, Christopher Donald

A cam carrier assembly includes a body made of a material lighter than aluminum. The body has a first side operably coupled with a cylinder head and a second side having bearing surfaces with bearing inserts. The bearing inserts support the camshaft. A series of apertures extend between the first and second sides of the body. Lobes of the camshaft operably couple with the valves of the cylinder head through the series of apertures extending between the first and second sides of the body.

Estimating Preferences for Treatments in Patients With Localized Prostate Cancer

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ávila, Mónica; CIBER en Epidemiología y Salud Pública; Universitat Pompeu Fabra, Barcelona

Purpose: Studies of patients' preferences for localized prostate cancer treatments have assessed radical prostatectomy and external radiation therapy, but none of them has evaluated brachytherapy. The aim of our study was to assess the preferences and willingness to pay of patients with localized prostate cancer who had been treated with radical prostatectomy, external radiation therapy, or brachytherapy, and their related urinary, sexual, and bowel side effects. Methods and Materials: This was an observational, prospective cohort study with follow-up until 5 years after treatment. A total of 704 patients with low or intermediate risk localized prostate cancer were consecutively recruited from 2003more » to 2005. The estimation of preferences was conducted using time trade-off, standard gamble, and willingness-to-pay methods. Side effects were measured with the Expanded Prostate Index Composite (EPIC), a prostate cancer-specific questionnaire. Tobit models were constructed to assess the impact of treatment and side effects on patients' preferences. Propensity score was applied to adjust for treatment selection bias. Results: Of the 580 patients reporting preferences, 165 were treated with radical prostatectomy, 152 with external radiation therapy, and 263 with brachytherapy. Both time trade-off and standard gamble results indicated that the preferences of patients treated with brachytherapy were 0.06 utilities higher than those treated with radical prostatectomy (P=.01). Similarly, willingness-to-pay responses showed a difference of €57/month (P=.004) between these 2 treatments. Severe urinary incontinence presented an independent impact on the preferences elicited (P<.05), whereas no significant differences were found by bowel and sexual side effects. Conclusions: Our findings indicate that urinary incontinence is the side effect with the highest impact on preferences and that brachytherapy and external radiation therapy are more valued than radical prostatectomy. These time trade-off and standard gamble preference assessments as well as the willingness-to-pay estimation could be useful to perform respectively cost-utility or cost-benefit analyses, which can guide health policy decisions.« less

Light metal production

DOEpatents

Fan, Qinbai

2016-04-19

An electrochemical process for the production of light metals, particularly aluminum. Such a process involves contacting a light metal source material with an inorganic acid to form a solution containing the light metal ions in high concentration. The solution is fed to an electrochemical reactor assembly having an anode side containing an anode and a cathode side containing a cathode, with anode side and the cathode side separated by a bipolar membrane, with the solution being fed to the anode side. Light metal ions are electrochemically transferred through the bipolar membrane to the cathode side. The process further involves reducing the light metal ions to light metal powder. An associated processing system is also provided.

Video Material as an Effective Educational Tool to Address Informational and Educational Needs of Cancer Patients Undergoing Radiation Therapy.

PubMed

Nathoo, Dilshad

2017-06-01

With increasing rates of cancer patients undergoing radiation therapy, the treatment itself can cause patients significant amounts of anxiety and distress. This can be attributed to the diagnosis of the disease, lack of knowledge of what radiation therapy is, expectations and management of side effects, and the lack of knowledge of supportive care for patients and their families. Providing patients with effective educational tools to meet the informational needs of cancer patients undergoing radiation therapy can empower patients and allow them to participate in treatment decision-making and their own healthcare. This discussion paper will evaluate several studies on the psychological impact of cancer patients undergoing radiation therapy and how video material can effectively meet the informational and educational needs of this patient population group.

The effects of cervical traction, cranial rhythmic impulse, and Mckenzie exercise on headache and cervical muscle stiffness in episodic tension-type headache patients.

PubMed

Choi, Sung-Yong; Choi, Jung-Hyun

2016-03-01

[Purpose] The purpose of this study was to examine the effects of cervical traction treatment, cranial rhythmic impulse treatment, a manual therapy, and McKenzie exercise, a dynamic strengthening exercise, on patients who have the neck muscle stiffness of the infrequent episodic tension-type (IETTH) headache and frequent episodic tension-type headache(FETTH), as well as to provide the basic materials for clinical interventions. [Subjects] Twenty-seven subjects (males: 15, females: 12) who were diagnosed with IETTH and FETTH after treatment by a neurologist were divided into three groups: (a cervical traction group (CTG, n=9), a cranial rhythmic contractiongroup (CRIG, n=9), and a McKenzie exercise group (MEG, n=9). An intervention was conducted for each group and the differences in their degrees of neck pain and changes in muscle tone were observed. [Results] In the within-group comparison of each group, headache significantly decreased in CTG. According to the results of the analysis of the muscle tone of the upper trapezius, there was a statistically significant difference in MEG on the right side and in CRIG on the left side. According to the results of the analysis of the muscle tone of the sternocleidomastoid muscle, there was a statistically significant difference in MEG on the right side and in CRIG on the left side. [Conclusion] In the comparison of the splenius capitis muscle between the groups, there was a statistically significant difference on the right side. Hence, compared to the other methods, cervical traction is concluded to be more effective at reducing headaches in IETTH and FETTH patients.

Risperidone-Induced Renal Damage and Metabolic Side Effects: The Protective Effect of Resveratrol

PubMed Central

Korkmaz, Deniz Taştemir; Azirak, Sebile; Güvenç, Ayşe Nilay; Kocaman, Nevin

2017-01-01

Objective The aim of the study was to investigate the possible protective qualities of resveratrol (RSV) against the side effects of risperidone (RIS) in an experimental model in rat kidneys with histologic and biochemical assessments. Materials and Methods Experimental procedures were performed on 35 female Sprague Dawley rats. Rats were randomly divided into five groups: control, untreated rats (n = 7) were in group 1; group 2 was given 2 mg/kg/day RIS (n = 7); group 3 was treated with 2 mg/kg/day RIS and 20 mg/kg/day RSV (n = 7); group 4 was treated with 2 mg/kg/day RIS and 40 mg/kg/day RSV (n = 7); and group 5 was treated with 2 mg/kg/day RIS and 80 mg/kg/day RSV (n = 7). All treatments were administered for two weeks by gavage. On treatment day 15, kidney tissues were removed for analysis. Results The results showed that RSV treatment reduced weight gain induced by RIS. In addition, RSV increased the total antioxidant status (TAS) and decreased serum creatinine (Cr), blood urea nitrogen (BUN), oxidative stress index (OSI), and total oxidant status (TOS) levels significantly (p < 0.05). Conclusion This study revealed that treatment with RSV might protect kidney tissues against the side effects of RIS. RSV could be an effective course of therapy to enhance therapeutic efficacy. PMID:28706577

Target detection portal

DOEpatents

Linker, Kevin L.; Brusseau, Charles A.

2002-01-01

A portal apparatus for screening persons or objects for the presence of trace amounts of target substances such as explosives, narcotics, radioactive materials, and certain chemical materials. The portal apparatus can have a one-sided exhaust for an exhaust stream, an interior wall configuration with a concave-shape across a horizontal cross-section for each of two facing sides to result in improved airflow and reduced washout relative to a configuration with substantially flat parallel sides; air curtains to reduce washout; ionizing sprays to collect particles bound by static forces, as well as gas jet nozzles to dislodge particles bound by adhesion to the screened person or object. The portal apparatus can be included in a detection system with a preconcentrator and a detector.

Effects of first premolar extraction on maxillary and mandibular third molar angulation after orthodontic therapy

PubMed Central

Gohilot, Avinash; Pradhan, Tejashri; Keluskar, Kanhoba Mahabaleshwar

2012-01-01

Background/Aims To compare the change in the angulation of developing mandibular third molar in both first premolar extraction and non-extraction cases and to determine whether premolar extraction results in a more mesial movement of the mandibular buccal segment and causes favorable rotational changes in the mandibular third molar tilt, which can enhance later eruption of the third molars. Materials and methods Pretreatment (T1) and post treatment (T2) panoramic radiographs were taken of 25 subjects (age 14–19 years) who had been treated by the extraction of all the first premolars and 25 subjects who had been treated with non-extraction. The horizontal reference plane was used to measure and compare the changes in the angles of the developing mandibular third molars. Results The mean uprighting of the maxillary third molars seen in the extraction group was 4 ± 9° on the left side and −17 ± 13° on the right side following treatment (T2 _ T1). For the non-extraction group the mean difference was −16 ± 12° on the left side and 2 ± 13° on the right side. There was a statistically significant difference between the groups (P _ 0.021 on the right side and P _ 0.041 on the left side). Mandibular 3rd molars in extraction group showed no statistical significant change in the angulation. Conclusion Premolar extractions had a positive influence on the developing maxillary third molar angulations both on right and left. Mandibular 3rd molar have shown change in the angulation but not statistically significant. Non-extraction therapy did not have any adverse effect. PMID:25737843

Effectiveness of fibrin adhesive in facial nerve anastomosis in dogs compared with standard microsuturing technique.

PubMed

Attar, Bijan Movahedian; Zalzali, Haidar; Razavi, Mohammad; Ghoreishian, Mehdi; Rezaei, Majid

2012-10-01

Epineural suturing is the most common technique used for peripheral nerve anastomosis. In addition to the foreign body reaction to the suture material, the surgical duration and difficulty of suturing in confined anatomic locations are major problems. We evaluated the effectiveness of fibrin glue as an acceptable alternative for nerve anastomosis in dogs. Eight adult female dogs weighing 18 to 24 kg were used in the present study. The facial nerve was transected bilaterally. On the right side, the facial nerve was subjected to epineural suturing; and on the left side, the nerve was anastomosed using fibrin adhesive. After 16 weeks, the nerve conduction velocity and proportion of the nerve fibers that crossed the anastomosis site were evaluated and compared for the epineural suture (right side) and fibrin glue (left side). The data were analyzed using the paired t test and univariate analysis of variance. The mean postoperative nerve conduction velocity was 29.87 ± 7.65 m/s and 26.75 ± 3.97 m/s on the right and left side, respectively. No statistically significant difference was found in the postoperative nerve conduction velocity between the 2 techniques (P = .444). The proportion of nerve fibers that crossed the anastomotic site was 71.25% ± 7.59% and 72.25% ± 8.31% on the right and left side, respectively. The histologic evaluation showed no statistically significant difference in the proportion of the nerve fibers that crossed the anastomotic site between the 2 techniques (P = .598). The results suggest that the efficacies of epineural suturing and fibrin gluing in peripheral nerve anastomosis are similar. Copyright © 2012 American Association of Oral and Maxillofacial Surgeons. Published by Elsevier Inc. All rights reserved.

A unified frame of predicting side effects of drugs by using linear neighborhood similarity.

PubMed

Zhang, Wen; Yue, Xiang; Liu, Feng; Chen, Yanlin; Tu, Shikui; Zhang, Xining

2017-12-14

Drug side effects are one of main concerns in the drug discovery, which gains wide attentions. Investigating drug side effects is of great importance, and the computational prediction can help to guide wet experiments. As far as we known, a great number of computational methods have been proposed for the side effect predictions. The assumption that similar drugs may induce same side effects is usually employed for modeling, and how to calculate the drug-drug similarity is critical in the side effect predictions. In this paper, we present a novel measure of drug-drug similarity named "linear neighborhood similarity", which is calculated in a drug feature space by exploring linear neighborhood relationship. Then, we transfer the similarity from the feature space into the side effect space, and predict drug side effects by propagating known side effect information through a similarity-based graph. Under a unified frame based on the linear neighborhood similarity, we propose method "LNSM" and its extension "LNSM-SMI" to predict side effects of new drugs, and propose the method "LNSM-MSE" to predict unobserved side effect of approved drugs. We evaluate the performances of LNSM and LNSM-SMI in predicting side effects of new drugs, and evaluate the performances of LNSM-MSE in predicting missing side effects of approved drugs. The results demonstrate that the linear neighborhood similarity can improve the performances of side effect prediction, and the linear neighborhood similarity-based methods can outperform existing side effect prediction methods. More importantly, the proposed methods can predict side effects of new drugs as well as unobserved side effects of approved drugs under a unified frame.

What matters when judging intentionality-moral content or normative status? Testing the rational scientist model of the side-effect.

PubMed

Papadopoulos, C; Hayes, B K

2018-06-01

Previous work has demonstrated a "side-effect effect," such that intentionality is more likely to be attributed to agents who bring about negatively valenced as opposed to positively valenced side effects. The rational-scientist model explains this by suggesting that norm-violating side effects are more informative for inferring intentionality than norm-conforming side effects. In the present study we reexamined this account, addressing limitations of previous empirical tests (e.g., Uttich & Lombrozo, Cognition 116: 87-100, 2010). Side-effect valence and norm status were manipulated factorially, enabling an examination of the impact of norm status on intentionality judgments in both positively and negatively valenced side effects. Additionally, the impact of side-effect norm status on the perceived valences of side effects and agents was examined. Effects of norm status were found for both positive and negative side effects. Violation of an ostensibly neutral norm led to negative perceptions of the side effect. However, a norm status effect on intentionality judgments persisted when these effects were controlled. These results support the view that the side-effect effect is the result of the rational use of social-cognitive evidence.

The United States’ Vulnerability to Coercion by China in the Rare Earths Market

DTIC Science & Technology

2012-12-14

a computer, is assembled in a third country. This has brought down the total cost of such products which has had very positive effects on the...world’s economy. When materials or resources can be obtained from multiple sources around the world, costs of procurement and manufacture are lower, which...results in the total cost of goods being overall less expensive. Sometimes there is the possibility of a very dangerous side effect from relying 2

Incidence and severity of self-reported chemotherapy side effects in routine care: A prospective cohort study

PubMed Central

Haas, Marion; Viney, Rosalie; Pearson, Sallie-Anne; Haywood, Philip; Brown, Chris; Ward, Robyn

2017-01-01

Aim Chemotherapy side effects are often reported in clinical trials; however, there is little evidence about their incidence in routine clinical care. The objective of this study was to describe the frequency and severity of patient-reported chemotherapy side effects in routine care across treatment centres in Australia. Methods We conducted a prospective cohort study of individuals with breast, lung or colorectal cancer undergoing chemotherapy. Side effects were identified by patient self-report. The frequency, prevalence and incidence rates of side effects were calculated by cancer type and grade, and cumulative incidence curves for each side effect computed. Frequencies of side effects were compared between demographic subgroups using chi-squared statistics. Results Side effect data were available for 449 eligible individuals, who had a median follow-up of 5.64 months. 86% of participants reported at least one side effect during the study period and 27% reported a grade IV side effect, most commonly fatigue or dyspnoea. Fatigue was the most common side effect overall (85%), followed by diarrhoea (74%) and constipation (74%). Prevalence and incidence rates were similar across side effects and cancer types. Age was the only demographic factor associated with the incidence of side effects, with older people less likely to report side effects. Conclusion This research has produced the first Australian estimates of self-reported incidence of chemotherapy side effects in routine clinical care. Chemotherapy side effects in routine care are common, continue throughout chemotherapy and can be serious. This work confirms the importance of observational data in providing clinical practice-relevant information to decision-makers. PMID:29016607

Incidence and severity of self-reported chemotherapy side effects in routine care: A prospective cohort study.

PubMed

Pearce, Alison; Haas, Marion; Viney, Rosalie; Pearson, Sallie-Anne; Haywood, Philip; Brown, Chris; Ward, Robyn

2017-01-01

Chemotherapy side effects are often reported in clinical trials; however, there is little evidence about their incidence in routine clinical care. The objective of this study was to describe the frequency and severity of patient-reported chemotherapy side effects in routine care across treatment centres in Australia. We conducted a prospective cohort study of individuals with breast, lung or colorectal cancer undergoing chemotherapy. Side effects were identified by patient self-report. The frequency, prevalence and incidence rates of side effects were calculated by cancer type and grade, and cumulative incidence curves for each side effect computed. Frequencies of side effects were compared between demographic subgroups using chi-squared statistics. Side effect data were available for 449 eligible individuals, who had a median follow-up of 5.64 months. 86% of participants reported at least one side effect during the study period and 27% reported a grade IV side effect, most commonly fatigue or dyspnoea. Fatigue was the most common side effect overall (85%), followed by diarrhoea (74%) and constipation (74%). Prevalence and incidence rates were similar across side effects and cancer types. Age was the only demographic factor associated with the incidence of side effects, with older people less likely to report side effects. This research has produced the first Australian estimates of self-reported incidence of chemotherapy side effects in routine clinical care. Chemotherapy side effects in routine care are common, continue throughout chemotherapy and can be serious. This work confirms the importance of observational data in providing clinical practice-relevant information to decision-makers.

Enzymatic characterization of peptidic materials isolated from aqueous solutions of ammonium cyanide (pH 9) and hydrocyanic acid (pH 6) exposed to ionizing radiation.

PubMed

Niketic, V; Draganić, Z; Nesković, S; Draganić, I

1982-01-01

The enzymatic digestion of some radiolytically produced peptidic materials was examined. The substrates were compounds isolated from 0.1 molar solutions of NH4CN (pH 9) and HCN (pH 6), after their exposure to gamma rays from a 60Co source (15-20 Mrad doses). Commercial proteolytic enzymes pronase and aminopeptidase M were used. The examined materials were of composite nature and proteolytic action was systematically observed after their subsequent purification. In some fractions the effect was found to be positive with up to 30% of peptide bonds cleaved with respect to the amino acid content. These findings support our previous conclusions on the free radical induced formation of peptidic backbones without the intervention of amino acids. Some side effects were also noted which might be of interest in observations on enzymatic cleavage of other composite peptidic materials of abiotic origin.

Quantum transport through 3D Dirac materials

NASA Astrophysics Data System (ADS)

Salehi, M.; Jafari, S. A.

2015-08-01

Bismuth and its alloys provide a paradigm to realize three dimensional materials whose low-energy effective theory is given by Dirac equation in 3+1 dimensions. We study the quantum transport properties of three dimensional Dirac materials within the framework of Landauer-Büttiker formalism. Charge carriers in normal metal satisfying the Schrödinger equation, can be split into four-component with appropriate matching conditions at the boundary with the three dimensional Dirac material (3DDM). We calculate the conductance and the Fano factor of an interface separating 3DDM from a normal metal, as well as the conductance through a slab of 3DDM. Under certain circumstances the 3DDM appears transparent to electrons hitting the 3DDM. We find that electrons hitting the metal-3DDM interface from metallic side can enter 3DDM in a reversed spin state as soon as their angle of incidence deviates from the direction perpendicular to interface. However the presence of a second interface completely cancels this effect.

Side-by-side ANFIS as a useful tool for estimating correlated thermophysical properties

NASA Astrophysics Data System (ADS)

Grieu, Stéphane; Faugeroux, Olivier; Traoré, Adama; Claudet, Bernard; Bodnar, Jean-Luc

2015-12-01

In the present paper, an artificial intelligence-based approach dealing with the estimation of correlated thermophysical properties is designed and evaluated. This new and "intelligent" approach makes use of photothermal responses obtained when homogeneous materials are subjected to a light flux. Commonly, gradient-based algorithms are used as parameter estimation techniques. Unfortunately, such algorithms show instabilities leading to non-convergence in case of correlated properties to be estimated from a rebuilt impulse response. So, the main objective of the present work was to simultaneously estimate both the thermal diffusivity and conductivity of homogeneous materials, from front-face or rear-face photothermal responses to pseudo random binary signals. To this end, we used side-by-side neuro-fuzzy systems (adaptive network-based fuzzy inference systems) trained with a hybrid algorithm. We focused on the impact on generalization of both the examples used during training and the fuzzification process. In addition, computation time was a key point to consider. That is why the developed algorithm is computationally tractable and allows both the thermal diffusivity and conductivity of homogeneous materials to be simultaneously estimated with very good accuracy (the generalization error ranges between 4.6% and 6.2%).

GRAPHITE BLOCKS ARE ARRAYED IN "THERMAL COLUMN" ON NORTH SIDE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

GRAPHITE BLOCKS ARE ARRAYED IN "THERMAL COLUMN" ON NORTH SIDE OF REACTOR. INL NEGATIVE NO. 4000. Unknown Photographer, 12/28/1951 - Idaho National Engineering Laboratory, Test Reactor Area, Materials & Engineering Test Reactors, Scoville, Butte County, ID

Coatings on reflective mask substrates

DOEpatents

Tong, William Man-Wai; Taylor, John S.; Hector, Scott D.; Mangat, Pawitter J. S.; Stivers, Alan R.; Kofron, Patrick G.; Thompson, Matthew A.

2002-01-01

A process for creating a mask substrate involving depositing: 1) a coating on one or both sides of a low thermal expansion material EUVL mask substrate to improve defect inspection, surface finishing, and defect levels; and 2) a high dielectric coating, on the backside to facilitate electrostatic chucking and to correct for any bowing caused by the stress imbalance imparted by either other deposited coatings or the multilayer coating of the mask substrate. An film, such as TaSi, may be deposited on the front side and/or back of the low thermal expansion material before the material coating to balance the stress. The low thermal expansion material with a silicon overlayer and a silicon and/or other conductive underlayer enables improved defect inspection and stress balancing.

Rational Design of Pathogen-Mimicking Amphiphilic Materials as Nanoadjuvants

NASA Astrophysics Data System (ADS)

Ulery, Bret D.; Petersen, Latrisha K.; Phanse, Yashdeep; Kong, Chang Sun; Broderick, Scott R.; Kumar, Devender; Ramer-Tait, Amanda E.; Carrillo-Conde, Brenda; Rajan, Krishna; Wannemuehler, Michael J.; Bellaire, Bryan H.; Metzger, Dennis W.; Narasimhan, Balaji

2011-12-01

An opportunity exists today for cross-cutting research utilizing advances in materials science, immunology, microbial pathogenesis, and computational analysis to effectively design the next generation of adjuvants and vaccines. This study integrates these advances into a bottom-up approach for the molecular design of nanoadjuvants capable of mimicking the immune response induced by a natural infection but without the toxic side effects. Biodegradable amphiphilic polyanhydrides possess the unique ability to mimic pathogens and pathogen associated molecular patterns with respect to persisting within and activating immune cells, respectively. The molecular properties responsible for the pathogen-mimicking abilities of these materials have been identified. The value of using polyanhydride nanovaccines was demonstrated by the induction of long-lived protection against a lethal challenge of Yersinia pestis following a single administration ten months earlier. This approach has the tantalizing potential to catalyze the development of next generation vaccines against diseases caused by emerging and re-emerging pathogens.

Model photo-responsive elastomers based on the self-assembly of side group liquid crystal triblock copolymers (Presentation Recording)

NASA Astrophysics Data System (ADS)

Kurji, Zuleikha; Kornfield, Julia A.; Kuzyk, Mark G.

2015-10-01

We report the synthesis of azobenzene-containing coil-liquid crystal-coil triblock copolymers that form uniform and highly reproducible elastomers by self-assembly. To serve as actuators to (non-invasively) steer a fiber optic, for example in deep brain stimulation, the polymers are designed to become monodomain "single liquid crystal" elastomers during the fiber-draw process and to have a large stress/strain response to stimulation with either light or heat. A fundamental scientific question that we seek to answer is how the interplay between the concentration of photoresponsive mesogens and the proximity to the nematic-isotropic transition governs the sensitivity of the material to stimuli. Specifically, a matched pair of polymers, one with ~5% azobenzene-containing side groups (~95% cyanobiphenyl side groups) and the other with 100% cyanobiphenyl side groups were synthesized from identical triblock pre-polymers (with polystyerene end blocks and 1,2-polybutadiene midblocks). These can be blended in various ratios to prepare a series of elastomers that are precisely matched in terms of the backbone length between physical crosslinks (because each polymer is derived from the same pre-polymer), while differing in % azobenzene side groups, allowing the effect of concentration of photoresponsive groups to be unambiguously determined.

All-electric spin modulator based on a two-dimensional topological insulator

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xiao, Xianbo; Ai, Guoping; Liu, Ying

2016-01-18

We propose and investigate a spin modulator device consisting of two ferromagnetic leads connected by a two-dimensional topological insulator as the channel material. It exploits the unique features of the topological spin-helical edge states, such that the injected carriers with a non-collinear spin-polarization direction would travel through both edges and show interference effect. The conductance of the device can be controlled in a simple and all-electric manner by a side-gate voltage, which effectively rotates the spin-polarization of the carrier. At low voltages, the rotation angle is linear in the gate voltage, and the device can function as a good spin-polarizationmore » rotator by replacing the drain electrode with a non-magnetic material.« less

Shade material evaluation using a cattle response model and meteorological instrumentation.

PubMed

Eigenberg, Roger A; Brown-Brandl, Tami M; Nienaber, John A

2010-11-01

Shade structures are often considered as one method of reducing stress in feedlot cattle. Selection of a suitable shade material can be difficult without data that quantify material effectiveness for stress reduction. A summer study was conducted during 2007 using instrumented shade structures in conjunction with meteorological measurements to estimate relative effectiveness of various shade materials. Shade structures were 3.6 m by 6.0 m by 3.0 m high at the peak and 2.0 m high at the sides. Polyethylene shade cloth was used in three of the comparisons and consisted of effective coverings of 100%, 60% with a silver reflective coating, and 60% black material with no reflective coating. Additionally, one of the structures was fitted with a poly snow fence with an effective shade of about 30%. Each shade structure contained a solar radiation meter and a black globe thermometer to measure radiant energy received under the shade material. Additionally, meteorological data were collected as a non-shaded treatment and included temperature, humidity, wind speed, and solar radiation. Data analyses was conducted using a physiological model based on temperature, humidity, solar radiation and wind speed; a second model using black globe temperatures, relative humidity, and wind speed was used as well. Analyses of the data revealed that time spent in the highest stress category was reduced by all shade materials. Moreover, significant differences (P < 0.05) existed between all shade materials (compared to no-shade) for hourly summaries during peak daylight hours and for 'full sun' days.

Shade material evaluation using a cattle response model and meteorological instrumentation.

PubMed

Eigenberg, Roger A; Brown-Brandl, Tami M; Nienaber, John A

2009-11-01

Shade structures are often considered as one method of reducing stress in feedlot cattle. Selection of a suitable shade material can be difficult without data that quantify material effectiveness for stress reduction. A summer study was conducted during 2007 using instrumented shade structures in conjunction with meteorological measurements to estimate relative effectiveness of various shade materials. Shade structures were 3.6 m by 6.0 m by 3.0 m high at the peak and 2.0 m high at the sides. Polyethylene shade cloth was used in three of the comparisons and consisted of effective coverings of 100%, 60% with a silver reflective coating, and 60% black material with no reflective coating. Additionally, one of the structures was fitted with a poly snow fence with an effective shade of about 30%. Each shade structure contained a solar radiation meter and a black globe thermometer to measure radiant energy received under the shade material. Additionally, meteorological data were collected as a non-shaded treatment and included temperature, humidity, wind speed, and solar radiation. Data analyses was conducted using a physiological model based on temperature, humidity, solar radiation and wind speed; a second model using black globe temperatures, relative humidity, and wind speed was used as well. Analyses of the data revealed that time spent in the highest stress category was reduced by all shade materials. Moreover, significant differences (P < 0.05) existed between all shade materials (compared to no-shade) for hourly summaries during peak daylight hours and for 'full sun' days.

Shade material evaluation using a cattle response model and meteorological instrumentation.

PubMed

Eigenberg, Roger A; Brown-Brandl, Tami M; Nienaber, John A

2010-09-01

Shade structures are often considered as one method of reducing stress in feedlot cattle. Selection of a suitable shade material can be difficult without data that quantify material effectiveness for stress reduction. A summer study was conducted during 2007 using instrumented shade structures in conjunction with meteorological measurements to estimate relative effectiveness of various shade materials. Shade structures were 3.6 m x 6.0 m x 3.0 m high at the peak and 2.0 m high at the sides. Polyethylene shade cloth was used in three of the comparisons and consisted of effective coverings of 100%, 60% with a silver reflective coating, and 60% black material with no reflective coating. Additionally, one of the structures was fitted with a poly snow fence with an effective shade of about 30%. Each shade structure contained a solar radiation meter and a black globe thermometer to measure radiant energy received under the shade material. Additionally, meteorological data were collected as a non-shaded treatment and included temperature, humidity, wind speed, and solar radiation. Data analyses was conducted using a physiological model based on temperature, humidity, solar radiation and wind speed; a second model using black globe temperatures, relative humidity, and wind speed was used as well. Analyses of the data revealed that time spent in the highest stress category was reduced by all shade materials. Moreover, significant differences (P < 0.05) existed between all shade materials (compared to no-shade) for hourly summaries during peak daylight hours and for 'full sun' days.

Side effects associated with anti-HIV drugs.

PubMed

Highleyman, L

1998-04-01

Many side effects are associated with the use of anti-HIV drugs, impacting the development of drug resistance and the quality of life for HIV-patients. Concern about side effects is a primary factor in deterring people from beginning HIV therapy. Frequency and severity of side effects vary greatly, but they are frequently more common and severe in people who are taking a new drug or who have advanced HIV disease. Information on side effects comes largely from clinical trials; however, many side effects are not discovered until the drug has been approved and used by larger numbers of people. Side effects vary from serious toxicities that require stopping treatment to uncomfortable or annoying side effects that interfere with daily life. A table categorizes the four major side effects (nausea, fever, skin rash, and fatigue) and divides them into grades that describe their intensity. A chart lists the side effects associated with specific anti-HIV drugs. Suggestions for managing side effects are included.

Effect of Backing Plate Thermal Property on Friction Stir Welding of 25-mm-Thick AA6061

NASA Astrophysics Data System (ADS)

Upadhyay, Piyush; Reynolds, Anthony

2014-04-01

By using backing plates made out of materials with widely varying thermal diffusivity this work seeks to elucidate the effects of the root side thermal boundary condition on weld process variables and resulting joint properties. Welds were made in 25.4-mm-thick AA6061 using ceramic, titanium, steel, and aluminum as backing plate (BP) material. Welds were also made using a "composite backing plate" consisting of longitudinal narrow strip of low diffusivity material at the center and two side plates of high diffusivity aluminum. Stir zone temperature during the welding was measured using two thermocouples spot welded at the core of the probe: one at the midplane height and another near the tip of the probe corresponding to the root of the weld. Steady state midplane probe temperatures for all the BPs used were found to be very similar. Near root peak temperature, however, varied significantly among weld made with different BPs all other things being equal. Whereas the near root and midplane temperature were the same in the case of ceramic backing plate, the root peak temperature was 318 K (45 °C) less than the midplane temperature in the case of aluminum BP. The trends of nugget hardness and grain size in through thickness direction were in agreement with the measured probe temperatures. Hardness and tensile test results show that the use of composite BP results in stronger joint compared to monolithic steel BP.

Investigation into the ring-substituted polyanilines and their application for the detection and adsorption of sulfur dioxide

PubMed Central

Tian, Yuhong; Qu, Ke; Zeng, Xiangqun

2017-01-01

It has been demonstrated in this study that the substituents on the monomer aniline benzene ring are able to introduce the significant differences to the resulting polyaniline’s collective properties. We systematically evaluated the structural perturbation effects of two substituents (methyl and methoxy) of aniline monomer through the electrochemical method. Our results showed that the methoxy group induces the less structural perturbation than the methyl counterpart, because of its partial double bond restriction. The morphologies are different for the polyaniline and the ring-substituted polyanilines, in which substituted polyanilines feature the larger porosities with the addition of these side groups. The influential effects of the methoxy side group have been further illustrated and amplified by its superior sensing performance towards the environmentally-significant sulfur dioxide gas, evaluated through the construction of the quartz crystal microbalance (QCM)-based gas sensor with these polyaniline materials. The as-constructed gas sensor’s sensitivity, selectivity and stability in terms of its SO2 responses have been evaluated in details. The methoxy-substituted polyaniline was tested to show the unique gas sensing properties for the sulfur dioxide at the low concentrations (50–250 ppm) and function as the adsorbing material at the high concentrations (500–1250 ppm). Thus it can be used both as sensing material as well as a novel filter and/or storage reservoir for the removal of sulfur dioxide pollutant from the environments. PMID:29033497

Porous polymethylmethacrylate as bone substitute in the craniofacial area.

PubMed

Bruens, Marco L; Pieterman, Herman; de Wijn, Joost R; Vaandrager, J Michael

2003-01-01

In craniofacial surgery, alloplastic materials are used for correcting bony defects. Porous polymethylmethacrylate (PMMA) is a biocompatible and nondegradable bone cement. Porous PMMA is formed by the classic bone cement formulation of methylmethacrylate liquid and PMMA powder in which an aqueous biodegradable carboxymethylcellulose gel is dispersed to create pores in the cement when cured. Pores give bone the opportunity to grow in, resulting in a better fixation of the prostheses. We evaluated the long-term results (n = 14), up to 20 years, of augmentations and defect fillings in the craniofacial area, with special interest in possible side effects and bone ingrowth. The evaluation consisted of a questionnaire, a physical examination, and a computed tomography (CT) scan. There were no side effects that could be ascribed to the porous PMMA. Twelve CT scans showed bone ingrowth into the prostheses, proving the validity behind the concept of porous PMMA.

Analysis of temperature profile and electric field in natural rubber glove due to microwave heating: effects of waveguide position

NASA Astrophysics Data System (ADS)

Keangin, P.; Narumitbowonkul, U.; Rattanadecho, P.

2018-01-01

Natural rubber (NR) is the key raw material used in the manufacture of other products such as rubber band, tire and shoes. Recently, the NR is used in natural rubber glove ( NRG) manufacturing in the industrial and medical fields. This research aims to investigate the electromagnetic wave propagation and heat transfer in NRG due to heating with microwave energy within the microwave oven at a microwave frequency of 2.45 GHz. Three-dimensional model of NRG and microwave oven are considered in this work. The comparative effects of waveguide position on the electric field and temperature profile in NRG when subjected to microwave energy are discussed. The finite element method (FEM) is used to solve the transient Maxwell’s equation coupled with the transient heat transfer equation. The simulation results with computer programs are validated with experimental results. The placement of waveguides in three cases are left hand side of microwave oven, right hand side of microwave oven and left and right hand sides of microwave oven are investigated. The findings revealed that the placing the waveguide on the right side of the microwave oven gives the highest electric field and temperature profile. The values obtained provide an indication toward understanding the study of heat transfer in NRG during microwave heating in the industry.

Side Effect Perceptions and Their Impact on Treatment Decisions in Women.

PubMed

Waters, Erika A; Pachur, Thorsten; Colditz, Graham A

2017-04-01

Side effects prompt some patients to forego otherwise-beneficial therapies. This study explored which characteristics make side effects particularly aversive. We used a psychometric approach, originating from research on risk perception, to identify the factors (or components) underlying side effect perceptions. Women ( N = 149) aged 40 to 74 years were recruited from a patient registry to complete an online experiment. Participants were presented with hypothetical scenarios in which an effective and necessary medication conferred a small risk of a single side effect (e.g., nausea, dizziness). They rated a broad range of side effects on several characteristics (e.g., embarrassing, treatable). In addition, we collected 4 measures of aversiveness for each side effect: choosing to take the medication, willingness to pay to avoid the side effect (WTP), negative affective attitude associated with the side effect, and how each side effect ranks among others in terms of undesirability. A principal components analysis (PCA) was used to identify the components underlying side effect perceptions. Then, for each aversiveness measure separately, regression analyses were used to determine which components predicted differences in aversiveness among the side effects. The PCA revealed 4 components underlying side effect perceptions: affective challenge (e.g., frightening), social challenge (e.g., disfiguring), physical challenge (e.g., painful), and familiarity (e.g., common). Side effects perceived as affectively and physically challenging elicited the highest levels of aversiveness across all 4 measures. Understanding what side effect characteristics are most aversive may inform interventions to improve medical decisions and facilitate the translation of novel biomedical therapies into clinical practice.

Side Effect Perceptions and their Impact on Treatment Decisions in Women

PubMed Central

Waters, Erika A.; Pachur, Thorsten; Colditz, Graham A.

2016-01-01

Background Side effects prompt some patients to forego otherwise-beneficial therapies. This study explored which characteristics make side effects particularly aversive. Methods We used a psychometric approach, originating from research on risk perception, to identify the factors (or components) underlying side effect perceptions. Women (N=149) aged 40–74 were recruited from a patient registry to complete an online experiment. Participants were presented with hypothetical scenarios in which an effective and necessary medication conferred a small risk of a single side effect (e.g., nausea, dizziness). They rated a broad range of side effects on several characteristics (e.g., embarrassing, treatable). In addition, we collected four measures of aversiveness for each side effect: choosing to take the medication, willingness to pay to avoid the side effect (WTP), negative affective attitude associated with the side effect, and how each side effect ranks among others in terms of undesirability. A principle-components analysis (PCA) was used to identify the components underlying side effect perceptions. Then, for each aversiveness measure separately, regression analyses were used to determine which components predicted differences in aversiveness among the side effects. Results The PCA revealed four components underlying side effect perceptions: affective challenge (e.g., frightening), social challenge (e.g., disfiguring), physical challenge (e.g., painful), and familiarity (e.g., common). Side effects perceived as affectively and physically challenging elicited the highest levels of aversiveness across all four measures. Conclusions Understanding what side effect characteristics are most aversive may inform interventions to improve medical decisions and facilitate the translation of novel biomedical therapies into clinical practice. PMID:27216581

Probes for multidimensional nanospectroscopic imaging and methods of fabrication thereof

DOEpatents

Weber-Bargioni, Alexander; Cabrini, Stefano; Bao, Wei; Melli, Mauro; Yablonovitch, Eli; Schuck, Peter J

2015-03-17

This disclosure provides systems, methods, and apparatus related to probes for multidimensional nanospectroscopic imaging. In one aspect, a method includes providing a transparent tip comprising a dielectric material. A four-sided pyramidal-shaped structure is formed at an apex of the transparent tip using a focused ion beam. Metal layers are deposited over two opposing sides of the four-sided pyramidal-shaped structure.

1200 to 1400 K slow strain rate compressive properties of NiAl/Ni2AlTi-base materials

NASA Technical Reports Server (NTRS)

Whittenberger, J. Daniel; Viswanadham, R. K.; Mannan, S. K.; Kumar, K. S.

1989-01-01

An attempt to apply the Martin Marietta Corporation's XD technology to the fabrication of NiAl-Ni2AlTi materials with improved creep properties is presented. Composite materials, containing from 0 to 30 vol pct of nominally 1-micron-diameter TiB2 particles in the intermetallic matrix have been produced by the XD process and compacted by hot pressing. Such composites demonstrated significant strength increases, approaching 3-fold for the 20 vol pct materials, in comparison to the unreinforced aluminide. This behavior was accomplished without deleterious side effects as the grain boundaries and particle-matrix interfaces were intact after compressive deformation to 10 percent or more strain. Typical true compressive stress-strain diagrams for materials tested in air between 1200 and 1400 K at approximate strain rates of 1.7 x 10 to the -6th/sec are presented.

Effect of Communication Style on Perceptions of Medication Side Effect Risk among Pharmacy Students.

PubMed

Sawant, Ruta V; Beatty, Collin R; Sansgiry, Sujit S

2016-10-25

Objective. To assess the effect of communication style, and frequency and severity of medication side-effects, on pharmacy students' perception of risk of experiencing side effects. Methods. One hundred responses from pharmacy students were obtained using an online survey. Participants were presented with a drug information box containing drug name, drug usage, and one side-effect associated with the drug. Information on side-effect for each drug was presented in one of eight experimental conditions, in a 2 (side-effect frequency: low, high), X2 (side-effect severity: mild, severe) X2 (communication style: verbal, verbal + natural frequency) factorial design. Risk perception of experiencing side effects was measured. Results. Communication style was found to have a significant impact on risk perception depending on the context of frequency and severity associated with the side effect. Conclusion. Communication style plays a significant role in formulating risk perceptions of medication side effects. Training in pharmaceutical counseling should include special emphasis on effective language use.

Dark Material Associated with and between Craters

NASA Image and Video Library

2011-11-18

This image from NASA Dawn spacecraft shows areas of dark material which are both associated with impact craters and between these craters on asteroid Vesta. Dark material is seen cropping out of the rims and sides of the larger craters.

Effect of mesh-peel ply variation on mechanical properties of E-glas composite by infusion vacuum method

NASA Astrophysics Data System (ADS)

Abdurohman, K.; Siahaan, Mabe

2018-04-01

Composite materials made of glass fiber EW-135 with epoxy lycal resin with vacuum infusion method have been performed. The dried glass fiber is arranged in a mold then connected to a vacuum machine and a resin tube. Then, the vacuum machine is turned on and at the same time the resin is sucked and flowed into the mold. This paper reports on the effect of using mesh- peel ply singles on upper-side laminates called A and the effect of using double mesh-peel ply on upper and lower-side laminates call B with glass fiber arrangement is normal and ± 450 in vacuum infusion process. Followed by the manufacture of tensile test specimen and tested its tensile strength with universal test machine 100kN Tensilon RTF 2410, at room temperature with constant crosshead speed. From tensile test results using single and double layers showed that double mesh-peel ply can increase tensile strength 14% and Young modulus 17%.

Layered devices having surface curvature and method of constructing same

DOEpatents

Woodbury, Richard C.; Perkins, Raymond T.; Thorne, James M.

1989-01-01

A method of treating a substrate having first and second sides with corresponding oppositely facing first and second surfaces, to produce curvature in the first surface. The method includes the steps of removing material, according to a predetermined pattern, from the second side of the substrate, and applying a stress-producing film of material to at least one surface of the substrate to thereby cause the substrate to bend to produce the desired curvature in the first surface.

3. BUILDING 522, EAST SIDE, FROM ACROSS 6TH STREET AT ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

3. BUILDING 522, EAST SIDE, FROM ACROSS 6TH STREET AT ITS INTERSECTION WITH G STREET, LOOKING NORTHWEST. - Oakland Naval Supply Center, Aeronautical Materials Storehouses, Between E & G Streets, between Fourth & Sixth Streets, Oakland, Alameda County, CA

Molecular dynamics simulation of amino acid ionic liquids near a graphene electrode: effects of alkyl side-chain length.

PubMed

Sadeghi Moghadam, Behnoosh; Razmkhah, Mohammad; Hamed Mosavian, Mohammad Taghi; Moosavi, Fatemeh

2016-12-07

Electric double layer (EDL) supercapacitors, using ionic liquid electrolytes, have been receiving a great deal of attention in response to the growing demand for energy storage systems. In the present study, the nanoscopic structure of amino acid ionic liquids (AAILs) as biodegradable electrolytes near a neutral graphene surface was studied by molecular dynamics (MD) simulation. In order to explore the influence of the anion type and structure, the effect of the alkyl side-chain length of amino acids on the EDL was investigated. The results for the AAILs, composed of 1-ethyl-3-methylimidazolium ([EMIM]) cations near alanine ([ALA]) and isoleucine ([ILE]) anions, were compared to a conventional electrolyte, [EMIM][PF 6 ]. A lower mobility of AAIL compared to [EMIM][PF 6 ], with diffusions as low as 10 -11 m 2 s -1 , was observed. The structural results demonstrated a layered structure near the surface and most of the adsorbed imidazolium cation rings lay flat on the graphene surface. Both MD and quantum computations were performed to shed light on the charge behavior of AAIL electrolytes. As the current results demonstrate, an increase in the anion side-chain length leads to a decrease in both the number of adsorbed ions on the surface and the thickness of the first adsorbed layer. More impressively, it was observed that a low charge concentration in the EDL of AAILs is due to more side-side interactions. This remarkable feature could introduce AAILs as more efficient electrolyte materials than conventional [EMIM][PF 6 ].

Translatory shock absorber for attitude sensors

NASA Technical Reports Server (NTRS)

Vonpragenau, G. L.; Morgan, I. T., Jr.; Kirby, C. A. (Inventor)

1976-01-01

A translatory shock absorber is provided for mounting an attitude sensor thereon for isolating a sensor from translatory vibrations. The translatory shock absorber includes a hollow block structure formed as one piece to form a parallelogram. The absorber block structure includes a movable top plate for supporting the attitude sensor and a fixed base plate with opposed side plates interposed between. At the junctions of the side plates, and the base and top plates, there are provided grooves which act as flexible hinges for attenuating translatory vibrations. A damping material is supported on a pedestal which is carried on the base plate between the side plates thereof. The top of the damping material rests against the bottom surface of the top plate for eliminating the resonant peaks of vibration.

Effects of shock-breakout pressure on ejection of micron-scale material from shocked tin surfaces

NASA Astrophysics Data System (ADS)

Zellner, M. B.; Grover, M.; Hammerberg, J. E.; Hixson, R. S.; Iverson, A. J.; Macrum, G. S.; Morley, K. B.; Obst, A. W.; Olson, R. T.; Payton, J. R.; Rigg, P. A.; Routley, N.; Stevens, G. D.; Turley, W. D.; Veeser, L.; Buttler, W. T.

2007-07-01

This effort investigates the relation between ejecta production and shock-breakout pressure (PSB) for Sn shocked with a Taylor shockwave (unsupported) to pressures near the solid-on-release/partial melt-on-release phase transition region. The shockwaves were created by detonation of high explosive (HE) PBX-9501 on the front side of Sn coupons. Ejecta production at the backside or free side of the Sn coupons was characterized through use of piezoelectric pins, optical shadowgraphy, x-ray attenuation radiography, and optical-heterodyne velocimetry. Ejecta velocities, dynamic volume densities, and areal densities were then correlated with the shock-breakout pressure of Sn surfaces characterized by roughness average of Ra=16 μin or Ra=32 μin.

Corrosion and Tribology of Materials Used in a Novel Reverse Hip Replacement.

PubMed

Braddon, Linda; Termanini, Zafer; MacDonald, Steven; Parvizi, Jay; Lieberman, Jay; Frankel, Victor; Zuckerman, Joseph

2017-07-05

Total hip arthroplasty has been utilized for the past 50 years as an effective treatment for degenerative, inflammatory and traumatic disorders of the hip. The design of these implants has generally followed the anatomy of the hip as a ball and socket joint with the femoral head representing the ball and the acetabulum representing the socket. We describe a novel hip arthroplasty design in which the "ball" is located on the acetabular side and the "socket" is located on the femoral side. The results of extensive biomechanical testing are described and document wear and corrosion characteristics that are at least equivalent to standard designs. These results support clinical assessment as the next step of the evaluation.

Corrosion and Tribology of Materials Used in a Novel Reverse Hip Replacement

PubMed Central

Braddon, Linda; Termanini, Zafer; MacDonald, Steven; Parvizi, Jay; Lieberman, Jay; Frankel, Victor; Zuckerman, Joseph

2017-01-01

Total hip arthroplasty has been utilized for the past 50 years as an effective treatment for degenerative, inflammatory and traumatic disorders of the hip. The design of these implants has generally followed the anatomy of the hip as a ball and socket joint with the femoral head representing the ball and the acetabulum representing the socket. We describe a novel hip arthroplasty design in which the “ball” is located on the acetabular side and the “socket” is located on the femoral side. The results of extensive biomechanical testing are described and document wear and corrosion characteristics that are at least equivalent to standard designs. These results support clinical assessment as the next step of the evaluation. PMID:28773112

Low-Temperature Solution Processable Electrodes for Piezoelectric Sensors Applications

NASA Astrophysics Data System (ADS)

Tuukkanen, Sampo; Julin, Tuomas; Rantanen, Ville; Zakrzewski, Mari; Moilanen, Pasi; Lupo, Donald

2013-05-01

Piezoelectric thin-film sensors are suitable for a wide range of applications from physiological measurements to industrial monitoring systems. The use of flexible materials in combination with high-throughput printing technologies enables cost-effective manufacturing of custom-designed, highly integratable piezoelectric sensors. This type of sensor can, for instance, improve industrial process control or enable the embedding of ubiquitous sensors in our living environment to improve quality of life. Here, we discuss the benefits, challenges and potential applications of piezoelectric thin-film sensors. The piezoelectric sensor elements are fabricated by printing electrodes on both sides of unmetallized poly(vinylidene fluoride) film. We show that materials which are solution processable in low temperatures, biocompatible and environmental friendly are suitable for use as electrode materials in piezoelectric sensors.

Observation and analysis of pellet material del B drift on MAST

DOE Office of Scientific and Technical Information (OSTI.GOV)

Garzotti, L.; Baylor, Larry R; Kochi, F.

2010-01-01

Pellet material deposited in a tokamak plasma experiences a drift towards the low field side of the torus induced by the magnetic field gradient. Plasma fuelling in ITER relies on the beneficial effect of this drift to increase the pellet deposition depth and fuelling efficiency. It is therefore important to analyse this phenomenon in present machines to improve the understanding of the del B induced drift and the accuracy of the predictions for ITER. This paper presents a detailed analysis of pellet material drift in MAST pellet injection experiments based on the unique diagnostic capabilities available on this machine andmore » compares the observations with predictions of state-of-the-art ablation and deposition codes.« less

Role of parenteral testosterone in hypospadias: A study from a teaching hospital in India

PubMed Central

Ahmad, Reyaz; Chana, Rajendra Singh; Ali, Syed Manazir; Khan, Shehtaj

2011-01-01

Objectives: To evaluate the effect of parenteral testosterone on penile length, preputial skin and side effects in patients with hypospadias. Materials and Methods: 23 patients with hypospadias were included in this study. An oily solution, each ml of which contained testosterone propionate 25 mg, and testosterone enanthate 110 mg, equivalent to 100 mg of testosterone was given deep intramuscularly 4, 3 and 2 weeks before reconstructive surgery at the dose of 2 mg/kg body weight. Increase in penile length, transverse preputial diameter, and diameter at the base of penis were noted. Basal testosterone levels were obtained before the institution of therapy and on the day of operation. In addition, side effect such as development of pubic hair and delay in bone age was noted. Results: Following parenteral testosterone administration, the mean increase in penile length, transverse preputial diameter and diameter at the base of penis was 1.35±0.40 cm (P<0.001), 1.40±0.47 cm (P<0.001), and 0.72±0.47 cm (P<0.001), respectively. Serum testosterone level after injection was well within normal range for that age. Minimal side effects were noted in form of development of fine pubic hair. Conclusion: We conclude that parenteral testosterone can be safely used to improve the surgical outcome of hypospadias repair. PMID:21976926

St. John's wort: a new alternative for depression?

PubMed

Josey, E S; Tackett, R L

1999-03-01

The primary purpose of this article is to review the existing literature concerning the therapeutic uses, adverse effects, and possible drug interactions of St. John's wort (Hypericum perforatum) as compared to other antidepressant medications. Reference material was obtained through database searches with time restrictions of 1985 to the present. Studies selected were those written in the English language which compared the role of St. John's wort, tricyclic antidepressants, monoamine oxidase inhibitors, and serotonin-selective reuptake inhibitors in the treatment of depression. Other studies were selected based on their evaluation of the safety and efficacy of St. John's wort as an antidepressant for a minimum of four weeks. A review of existing literature recognized nine clinical trials that reported the efficacy of St. John's wort as compared to placebo and to other antidepressant medications. Of these nine, four controlled studies were chosen based upon their large patient populations and their consistency in brand and dosage of St. John's wort used. These four studies demonstrated that St. John's wort was as effective as other antidepressant medications and more effective than placebo, as the clinical symptoms of depression greatly decreased upon administration of H. perforatum. The side-effect profile of H. perforatum at this time appears to be superior to any current U.S.-approved antidepressant medication. From the existing literature, St. John's wort appears to be a safe and effective alternative in the treatment of depression. Tricylic antidepressants and monoamine oxidase inhibitors can produce serious cardiac side-effects, such as tachycardia and postural hypotension, and many unwanted anticholinergic side-effects, including dry mouth and constipation. St. John's wort has proven to be free of any cardiac, as well as anticholinergic, side-effects normally seen with antidepressant medications. Based upon limited studies, St. John's wort appears to be an acceptable alternative to traditional antidepressant therapy, although trials on a larger scale are warranted in this area. Hypericum is available to the lay public as an over-the-counter preparation and may be misused if not fully understood.

Understanding the effect of side groups in ionic liquids on carbon-capture properties: a combined experimental and theoretical effort

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yan, Fangyong; Lartey, Michael; Damodaran, Krishnan

2013-01-01

Ionic liquids are an emerging class of materials with applications in a variety of fields. Steady progress has been made in the creation of ionic liquids tailored to specific applications. However, the understanding of the underlying structure–property relationships has been slower to develop. As a step in the effort to alleviate this deficiency, the influence of side groups on ionic liquid properties has been studied through an integrated approach utilizing synthesis, experimental determination of properties, and simulation techniques. To achieve this goal, a classical force field in the framework of OPLS/Amber force fields has been developed to predict ionic liquidmore » properties accurately. Cu(I)-catalyzed click chemistry was employed to synthesize triazolium-based ionic liquids with diverse side groups. Values of densities were predicted within 3% of experimental values, whereas self-diffusion coefficients were underestimated by about an order of magnitude though the trends were in excellent agreement, the activation energy calculated in simulation correlates well with experimental values. The predicted Henry coefficient for CO{sub 2} solubility reproduced the experimentally observed trends. This study highlights the importance of integrating experimental and computational approaches in property prediction and materials development, which is not only useful in the development of ionic liquids for CO{sub 2} capture but has application in many technological fields.« less

Understanding the effect of side groups in ionic liquids on carbon-capture properties: a combined experimental and theoretical effort

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yan, Fangyong; Lartey, Michael; Damodaran, Krishnan

Ionic liquids are an emerging class of materials with applications in a variety of fields. Steady progress has been made in the creation of ionic liquids tailored to specific applications. However, the understanding of the underlying structure–property relationships has been slower to develop. As a step in the effort to alleviate this deficiency, the influence of side groups on ionic liquid properties has been studied through an integrated approach utilizing synthesis, experimental determination of properties, and simulation techniques. To achieve this goal, a classical force field in the framework of OPLS/Amber force fields has been developed to predict ionic liquidmore » properties accurately. Cu(I)-catalyzed click chemistry was employed to synthesize triazolium-based ionic liquids with diverse side groups. Values of densities were predicted within 3% of experimental values, whereas self-diffusion coefficients were underestimated by about an order of magnitude though the trends were in excellent agreement, the activation energy calculated in simulation correlates well with experimental values. The predicted Henry coefficient for CO{sub 2} solubility reproduced the experimentally observed trends. This study highlights the importance of integrating experimental and computational approaches in property prediction and materials development, which is not only useful in the development of ionic liquids for CO{sub 2} capture but has application in many technological fields.« less

Non-graphite crucible for high temperature applications

DOEpatents

Holcombe, C.E.; Pfeiler, W.A.

1994-08-02

A multi-piece crucible for high temperature applications comprises a tubular side wall member having a lip on the inside surface and a bottom member or members forming a container for containing a melt of a material during a high temperature melt-casting operations. The multi-piece design prevents cracking of the crucible or leakage of the melt from the crucible during the melt-casting operation. The lip of the tubular member supports the bottom member. The contacting surfaces where the lip of the tubular side wall member contacts the bottom member of the multi-piece crucible contains a ceramic sealing material. The ceramic sealing material forms a seal sufficient to prevent the melt of the material from leaking out of the multi-piece crucible during the melt-casting process. The multi-piece crucible is made of a material which is chemically inert to the melt and has structural integrity at the melting point temperature of the melt, or of a material coated with such a material. 6 figs.

Non-graphite crucible for high temperature applications

DOEpatents

Holcombe, Cressie E.; Pfeiler, William A.

1994-01-01

A multi-piece crucible for high temperature applications comprises a tubular side wall member having a lip on the inside surface and a bottom member or members forming a container for containing a melt of a material during a high temperature melt-casting operations. The multi-piece design prevents cracking of the crucible or leakage of the melt from the crucible during the melt-casting operation. The lip of the tubular member supports the bottom member. The contacting surfaces where the lip of the tubular side wall member contacts the bottom member of the multi-piece crucible contains a ceramic sealing material. The ceramic sealing material forms a seal sufficient to prevent the melt of the material from leaking out of the multi-piece crucible during the melt-casting process. The multi-piece crucible is made of a material which is chemically inert to the melt and has structural integrity at the melting point temperature of the melt, or of a material coated with such a material.

Bipolar battery with array of sealed cells

DOEpatents

Kaun, Thomas D.; Smaga, John A.

1987-01-01

A lithium alloy/metal sulfide battery as a dipolar battery is disclosed with an array of stacked cells with the anode and cathode electrode materials in each cell sealed in a confining structure and separated from one another except across separator material interposed therebetween. The separator material is contained in a module having separate perforated metallic sheets that sandwich opposite sides of the separator material for the cell and an annular insulating spacer that surrounds the separator material beyond the perforations and is also sandwiched between and sealed to the sheets. The peripheral edges of the sheets project outwardly beyond the spacer, traverse the side edges of the adjacent electrode material to form cup-like electrode holders, and are fused to the adjacent current collector or end face members of the array. Electrolyte is infused into the electrolyte cavity through the perforations of one of the metallic sheets with the perforations also functioning to allow ionic conductance across the separator material between the adjacent electrodes. A gas-tight housing provides an enclosure of the array.

Photocathode

DOE Office of Scientific and Technical Information (OSTI.GOV)

Opachich, Yekaterina; MacPhee, Andrew

A photocathode designs that leverage the grazing incidence geometry yield improvements through the introduction of recessed structures, such as cones, pyramids, pillars or cavities to the photocathode substrate surface. Improvements in yield of up to 20 times have been shown to occur in grazing incidence geometry disclosed herein due to a larger path length of the X-ray photons which better matches the secondary electron escape depth within the photocathode material. A photocathode includes a substrate having a first side and a second side, the first side configured to receive x-ray energy and the second side opposing the first side. Amore » structured surface is associated with the second side of the substrate such that the structured surface includes a plurality of recesses from the second side of the substrate into the substrate.« less

Analysis Of Landslide Materials Spreading In Bendan Dhuwur Village Gajahmungkur Subdistrict Semarang City

NASA Astrophysics Data System (ADS)

Trisnawati, Devina; Najib; Kusuma, Istiqomah Ari; Husna, Anissa Fitratul

2018-02-01

Bendan Dhuwur is one of area in Semarang city, which continuously has landslide problem. This problem resulted in damage of some buildings and main road. Landslide materials/coluvial have been estimated lays on under those infrastructures and tend to move during rainy season. Therefore, it needs to understand the spread of coluvial to minimize the effect of landslide. Remote sensing method has been used to analyze multi temporal image for mapping landslide materials from different years recorded direction of creep and spread of coluvials. This method has been combined with surface and subsurface data from mapping and resistivity data. The analysis result on map which show that the coluvial material spreads on the south side, beneath the University of Tujuh Belas Agustus construction and Pawiyatan Luhur road. Its move to east leads to the Kaligarang river.

Improved performance of nanoscale junctionless tunnel field-effect transistor based on gate engineering approach

NASA Astrophysics Data System (ADS)

Molaei Imen Abadi, Rouzbeh; Sedigh Ziabari, Seyed Ali

2016-11-01

In this paper, a first qualitative study on the performance characteristics of dual-work function gate junctionless TFET (DWG-JLTFET) on the basis of energy band profile modulation is investigated. A dual-work function gate technique is used in a JLTFET in order to create a downward band bending on the source side similar to PNPN structure. Compared with the single-work function gate junctionless TFET (SWG-JLTFET), the numerical simulation results demonstrated that the DWG-JLTFET simultaneously optimizes the ON-state current, the OFF-state leakage current, and the threshold voltage and also improves average subthreshold slope. It is illustrated that if appropriate work functions are selected for the gate materials on the source side and the drain side, the JLTFET exhibits a considerably improved performance. Furthermore, the optimization design of the tunnel gate length ( L Tun) for the proposed DWG-JLTFET is studied. All the simulations are done in Silvaco TCAD for a channel length of 20 nm using the nonlocal band-to-band tunneling (BTBT) model.

Health Related Quality of Life in Patients with Side-Effects after Antimuscarinic Treatment for Overactive Bladder.

PubMed

Kim, Aram; Lee, Kyu-Sung; Jung, Rangrhee; Na, Selee; Kim, Joon-Chul; Kim, Hyeong Gon; Choo, Myung-Soo

2017-09-01

Drug therapy is the mainstay of treatment for overactive bladder (OAB), but antimuscarinic agents possess side-effects. These side-effects decrease the patients' quality of life. We therefore assessed the impact of side-effects on health-related quality of life (HR-QoL) through an analysis of EQ-5D questionnaire. This study was designed to investigate the patients' satisfaction by quality weight of health status as affected by the side-effects of OAB medications. Patients who had OAB symptoms lasting longer than 3 months and have experienced side-effects after any antimuscarinic treatments filled in the EQ-5D questionnaire. The enrolled patients had two EQ-5D questionnaires for two different health statuses, i.e., presence or absence of side-effects. Quality weight was calculated using the ED-5D health status score with Korean tariff. One hundred patients were enrolled and completed the HR-QoL questionnaire. The most prevalent side-effect was dry mouth (61%) and 28% patients had dry mouth and constipation concurrently. Most of the patients with side-effects tried to endure and overcome these side-effects (79%), but 10% desired a change in medication, and 6% stopped medication altogether. The quality weight of EQ-5D without side-effects was 0.863, while the quality weight with side-effects was 0.666 (P < 0.001). The VAS score was 79 in patient without side-effects and 57 in those with side-effects, supporting the results of quality weight assessment. Overactive bladder patients may enjoy a better quality of life if side-effects associated with antimuscarinic therapy are fewer. © 2016 John Wiley & Sons Australia, Ltd.

Comparison of the Efficacy, Side Effects, and Cost of Modafinil and Intranasal Mometasone Furoate in Obstructive Sleep Apnea-Hypopnea Syndrome: A Preliminary Clinical Study

PubMed Central

Zhang, Shujia; Duan, Zhongnin

2018-01-01

Background Obstructive sleep apnea-hypopnea syndrome (OSAHS) is characterized by repeated episodes of reduction in airflow due to the collapse of the upper airway during sleep. The aim of this study was to compare clinical outcome, side effects, and cost of treatment between modafinil and intranasal mometasone furoate in patients with OSAHS. Material/Methods Patients with OSAHS (N=250) were divided into two groups: the modafinil group (MG) (N=125) were treated with 100 mg modafinil twice a day; the intranasal mometasone furoate group (IMFG) (N=125) were treated with 100 μg of intranasal mometasone furoate in the evening. Quality of life, grading of OSAHS, plain-film radiography, the adenoidal-nasopharyngeal ratio (AN ratio), side effects, cost of treatment, and beneficial effects after discontinuation of treatment were evaluated for all patients. Results Duration of sleep apnea was significantly reduced in the IMFG compared with the MG (p=0.0145, q=9.262). Modafinil and intranasal mometasone furoate both had moderate effects on improvement of the OSAHS score. The IMFG showed a significantly greater beneficial effect on the AN ratio when compared with the MG (p=0.0001, q=6.584). No adverse events of treatment with modafinil and intranasal mometasone furoate were reported. Cost of treatment and beneficial effect after discontinuation were both significantly greater for the IMFG compared with the MG. Conclusions The findings of this preliminary clinical study were that for patients diagnosed with OSAHS, night-time treatment with intranasal mometasone furoate was more effective than modafinil. PMID:29749371

SOUTH WING, TRA661. SOUTH SIDE. CAMERA FACING NORTH. MTR HIGH ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

SOUTH WING, TRA-661. SOUTH SIDE. CAMERA FACING NORTH. MTR HIGH BAY BEYOND. INL NEGATIVE NO. HD46-45-3. Mike Crane, Photographer, 4/2005 - Idaho National Engineering Laboratory, Test Reactor Area, Materials & Engineering Test Reactors, Scoville, Butte County, ID

Gas pump with movable gas pumping panels

DOEpatents

Osher, John E.

1984-01-01

Apparatus for pumping gas continuously a plurality of articulated panels of getter material, each of which absorbs gases on one side while another of its sides is simultaneously reactivated in a zone isolated by the panels themselves from a working space being pumped.

Gas pump with movable gas pumping panels

DOEpatents

Osher, J.L.

Apparatus for pumping gas continuously a plurality of articulated panels of getter material, each of which absorbs gases on one side while another of its sides is simultaneously reactivated in a zone isolated by the panels themselves from a working space being pumped.

Integral manifolding structure for fuel cell core having parallel gas flow

DOEpatents

Herceg, Joseph E.

1984-01-01

Disclosed herein are manifolding means for directing the fuel and oxidant gases to parallel flow passageways in a fuel cell core. Each core passageway is defined by electrolyte and interconnect walls. Each electrolyte and interconnect wall consists respectively of anode and cathode materials layered on the opposite sides of electrolyte material, or on the opposite sides of interconnect material. A core wall projects beyond the open ends of the defined core passageways and is disposed approximately midway between and parallel to the adjacent overlaying and underlying interconnect walls to define manifold chambers therebetween on opposite sides of the wall. Each electrolyte wall defining the flow passageways is shaped to blend into and be connected to this wall in order to redirect the corresponding fuel and oxidant passageways to the respective manifold chambers either above or below this intermediate wall. Inlet and outlet connections are made to these separate manifold chambers respectively, for carrying the fuel and oxidant gases to the core, and for carrying their reaction products away from the core.

Integral manifolding structure for fuel cell core having parallel gas flow

DOEpatents

Herceg, J.E.

1983-10-12

Disclosed herein are manifolding means for directing the fuel and oxidant gases to parallel flow passageways in a fuel cell core. Each core passageway is defined by electrolyte and interconnect walls. Each electrolyte and interconnect wall consists respectively of anode and cathode materials layered on the opposite sides of electrolyte material, or on the opposite sides of interconnect material. A core wall projects beyond the open ends of the defined core passageways and is disposed approximately midway between and parallel to the adjacent overlaying and underlying interconnect walls to define manifold chambers therebetween on opposite sides of the wall. Each electrolyte wall defining the flow passageways is shaped to blend into and be connected to this wall in order to redirect the corresponding fuel and oxidant passageways to the respective manifold chambers either above or below this intermediate wall. Inlet and outlet connections are made to these separate manifold chambers respectively, for carrying the fuel and oxidant gases to the core, and for carrying their reaction products away from the core.

The Effect of Material and Side Walls on Hull Deflection during a Blast Event

DTIC Science & Technology

2017-12-13

by Danielle Abell SURVICE Engineering Company 4695 Millennium Dr Belcamp, MD 21017 under contract W911QX-16-D-0014...Laboratory. The views and conclusions contained in this document are those of SURVICE Engineering Company and the US Army Research Laboratory. Citation... Engineering Company 4695 Millennium Dr Belcamp, MD 21017 under contract W911QX-16-D-0014 Approved for public release

Graphene-Templated Synthesis of Magnetic Metal Organic Framework Nanocomposites for Selective Enrichment of Biomolecules.

PubMed

Cheng, Gong; Wang, Zhi-Gang; Denagamage, Sachira; Zheng, Si-Yang

2016-04-27

Successful control of homogeneous and complete coating of graphene or graphene-based composites with well-defined metal organic framework (MOF) layers is a great challenge. Herein, novel magnetic graphene MOF composites were constructed via a simple strategy for self-assembly of well-distributed, dense, and highly porous MOFs on both sides of graphene nanosheets. Graphene functionalized with magnetic nanoparticles and carboxylic groups on both sides was explored as the backbone and template to direct the controllable self-assembly of MOFs. The prepared composite materials have a relatively high specific surface area (345.4 m(2) g(-1)), and their average pore size is measured to be 3.2 nm. Their relatively high saturation magnetization (23.8 emu g(-1)) indicates their strong magnetism at room temperature. Moreover, the multifunctional composite was demonstrated to be a highly effective affinity material in selective extraction and separation of low-concentration biomolecules from biological samples, in virtue of the size-selection property of the unique porous structure and the excellent affinity of the composite materials. Besides providing a solution for the construction of well-defined functional graphene-based MOFs, this work could also contribute to selective extraction of biomolecules, in virtue of the universal affinity between immobilized metal ions and biomolecules.

Finite element simulation of the T-shaped ECAP processing of round samples

NASA Astrophysics Data System (ADS)

Shaban Ghazani, Mehdi; Fardi-Ilkhchy, Ali; Binesh, Behzad

2018-05-01

Grain refinement is the only mechanism that increases the yield strength and toughness of the materials simultaneously. Severe plastic deformation is one of the promising methods to refine the microstructure of materials. Among different severe plastic deformation processes, the T-shaped equal channel angular pressing (T-ECAP) is a relatively new technique. In the present study, finite element analysis was conducted to evaluate the deformation behavior of metals during T-ECAP process. The study was focused mainly on flow characteristics, plastic strain distribution and its homogeneity, damage development, and pressing force which are among the most important factors governing the sound and successful processing of nanostructured materials by severe plastic deformation techniques. The results showed that plastic strain is localized in the bottom side of sample and uniform deformation cannot be possible using T-ECAP processing. Friction coefficient between sample and die channel wall has a little effect on strain distributions in mirror plane and transverse plane of deformed sample. Also, damage analysis showed that superficial cracks may be initiated from bottom side of sample and their propagation will be limited due to the compressive state of stress. It was demonstrated that the V shaped deformation zone are existed in T-ECAP process and the pressing load needed for execution of deformation process is increased with friction.

46 CFR 169.323 - Furniture and furnishings.

Code of Federal Regulations, 2010 CFR

2010-10-01

... other material having equivalent fire resistant qualities. (e) Trash receptacles must be constructed of non-combustible materials with solid sides and bottoms and have solid noncombustible covers. Rails and...

46 CFR 169.323 - Furniture and furnishings.

Code of Federal Regulations, 2013 CFR

2013-10-01

... other material having equivalent fire resistant qualities. (e) Trash receptacles must be constructed of non-combustible materials with solid sides and bottoms and have solid noncombustible covers. Rails and...

46 CFR 169.323 - Furniture and furnishings.

Code of Federal Regulations, 2014 CFR

2014-10-01

... other material having equivalent fire resistant qualities. (e) Trash receptacles must be constructed of non-combustible materials with solid sides and bottoms and have solid noncombustible covers. Rails and...

Conductive polymer-based material

DOEpatents

McDonald, William F [Utica, OH; Koren, Amy B [Lansing, MI; Dourado, Sunil K [Ann Arbor, MI; Dulebohn, Joel I [Lansing, MI; Hanchar, Robert J [Charlotte, MI

2007-04-17

Disclosed are polymer-based coatings and materials comprising (i) a polymeric composition including a polymer having side chains along a backbone forming the polymer, at least two of the side chains being substituted with a heteroatom selected from oxygen, nitrogen, sulfur, and phosphorus and combinations thereof; and (ii) a plurality of metal species distributed within the polymer. At least a portion of the heteroatoms may form part of a chelation complex with some or all of the metal species. In many embodiments, the metal species are present in a sufficient concentration to provide a conductive material, e.g., as a conductive coating on a substrate. The conductive materials may be useful as the thin film conducting or semi-conducting layers in organic electronic devices such as organic electroluminescent devices and organic thin film transistors.

Photovoltaic and thermophotovoltaic devices with quantum barriers

DOEpatents

Wernsman, Bernard R [Jefferson Hills, PA

2007-04-10

A photovoltaic or thermophotovoltaic device includes a diode formed by p-type material and n-type material joined at a p-n junction and including a depletion region adjacent to said p-n junction, and a quantum barrier disposed near or in the depletion region of the p-n junction so as to decrease device reverse saturation current density while maintaining device short circuit current density. In one embodiment, the quantum barrier is disposed on the n-type material side of the p-n junction and decreases the reverse saturation current density due to electrons while in another, the barrier is disposed on the p-type material side of the p-n junction and decreases the reverse saturation current density due to holes. In another embodiment, both types of quantum barriers are used.

Explanations for side effect aversion in preventive medical treatment decisions

PubMed Central

Waters, Erika A.; Weinstein, Neil D.; Colditz, Graham A.; Emmons, Karen

2008-01-01

Objective Many laypeople demonstrate excessive sensitivity to negative side effects of medical treatments, which may lead them to refuse beneficial therapies. This Internet-based experiment investigated three possible explanations for such “side effect aversion.” One was derived from mental accounting, one examined the mere presence of a side effect, and one focused on computational difficulties. Design Participants (N = 5,379) were presented with a hypothetical cancer preventive treatment situation that was or was not accompanied by one or two small side effects. The side effects were either beneficial or harmful. In all conditions the net absolute risk reduction associated with the treatment was 15%. Main Outcome Measures Participants indicated their willingness to accept treatment and their perceptions of the treatment’s effects on their overall cancer risk. Results Data were consistent only with the “mere presence” explanation of side effect aversion, the idea that side effects act as a strong negative cue that directly affects treatment appraisal. The number of negative side effects did not influence treatment willingness. Conclusion Side effect aversion is a challenge to informed decision making. Specific mechanisms that produce side effect aversion should be identified. PMID:19290712

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chillara, Vamshi Krishna; Pantea, Cristian; Sinha, Dipen N.

Here, we numerically investigate the resonance and vibration characteristics of radial modes of laterally stiffened piezoelectric disc transducers. Lateral stiffening is modeled using a spring and vibration characteristics of the piezo-disc are investigated with increasing lateral stiffness. It is found that the resonant frequency response of the radial modes follows an asymptotic behavior approaching that of a clamped disc with increasing lateral stiffness. The radial mode vibration pattern of the discs is also found to be affected by lateral stiffness. While the vibration pattern of a free disc corresponds to a Bessel function, laterally stiffened discs show edge-effects where theymore » depart from the Bessel-like behavior. In addition, a fully clamped piezo-disc is found to have an extra side-lobe when compared to a free disc. Ultrasonic beam profiles generated from radial modes of laterally stiffened discs are numerically investigated. It is found that the free piezo-disc generates a Bessel beam that has multiple side-lobes. Increasing the lateral stiffness results in a significant reduction of side-lobes in the beam profile. This technique of generating a collimated beam with side-lobe reduction finds significant applications in imaging through concrete, drilling mud, and other highly attenuating materials.« less

Materials Performance in USC Steam Portland

DOE Office of Scientific and Technical Information (OSTI.GOV)

G.R. Holcomb; J. Tylczak; R. Hu

2011-04-26

Goals of the U.S. Department of Energy's Advanced Power Systems Initiatives include power generation from coal at 60% efficiency, which requires steam conditions of up to 760 C and 340 atm, co-called advanced ultrasupercritical (A-USC) steam conditions. A limitation to achieving the goal is a lack of cost-effective metallic materials that can perform at these temperatures and pressures. Some of the more important performance limitations are high-temperature creep strength, fire-side corrosion resistance, and steam-side oxidation resistance. Nickel-base superalloys are expected to be the materials best suited for steam boiler and turbine applications above about 675 C. Specific alloys of interestmore » include Haynes 230 and 282, Inconel 617, 625 and 740, and Nimonic 263. Further validation of a previously developed chromia evaporation model is shown by examining the reactive evaporation effects resulting from exposure of Haynes 230 and Haynes 282 to moist air environments as a function of flow rate and water content. These two alloys differ in Ti and Mn contents, which may form outer layers of TiO{sub 2} or Cr-Mn spinels. This would in theory decrease the evaporation of Cr{sub 2}O{sub 3} from the scale by decreasing the activity of chromia at the scale surface, and be somewhat self-correcting as chromia evaporation concentrates the Ti and Mn phases. The apparent approximate chromia activity was found for each condition and alloy that showed chromia evaporation kinetics. As expected, it was found that increasing the gas flow rate led to increased chromia evaporation and decreased chromia activity. However, increasing the water content in moist air increased the evaporation, but results were mixed with its effect on chromia activity.« less

The Composition of the Iapetus Dark Material, Hyperion and Phoebe

NASA Astrophysics Data System (ADS)

Stockstill, K. R.; Larson, S. M.; Vilas, F.; Gaffey, M. J.

1996-09-01

A linear mixing model has been used to separate the high-resolution visible/near-infrared reflectance spectrum of the Iapetus dark material from spectra of the leading and trailing sides of Iapetus. A distinct absorption feature centered at 0.67 mu m is apparent in the spectrum. A slight inflection covering 0.4 to 0.6 mu m and a change in slope near 0.73 mu m suggesting the lower wavelength edge of an absorption are also present. These absorption features are attributed to (6) A1 -> (4) T2(G) and (6) A1 -> (4) T1(G) charge transfer transitions in minerals such as goethite and hematite that are products of the aqueous alteration of anhydrous silicates. We confirm the strong, positive spectral slope attributed to organic material. Broadband photometry of Phoebe using ECAS filters was acquired on four nights in 1982 (Tholen and Zellner, Icarus, 1983). On two nights covering the same side of Phoebe, the photometry tested positively for an absorption feature centered at 0.7 mu m due to oxidized iron in phyllosilicates. The opposite side of Phoebe was covered by the other two observations. The spectral difference between two opposite sides of Phoebe suggests that an impact fragmented Phoebe's parent body, producing Phoebe at the junction of two different compositional units. High resolution reflectance spectra have been obtained of the Saturnian satellites Phoebe and Hyperion, the main candidates for a circumsaturnian origin of the Iapetus dark material. These will be discussed.

Effect of overcharge on Li(Ni 0.5Mn 0.3Co 0.2)O 2/Graphite lithium ion cells with poly(vinylidene fluoride) binder. I - Microstructural changes in the anode

DOE PAGES

Dietz Rago, Nancy; Bareno, Javier; Li, Jianlin; ...

2018-03-17

Cells based on NMC/graphite, containing poly(vinylidene difluoride) (PVDF) binders in the positive and negative electrodes, were systematically overcharged to 100, 120, 140, 160, 180, and 250% state-of-charge (SOC). At 250% SOC the cell vented. Scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) of the anodes showed several state-of-overcharge-dependent trends. Starting at 120% SOC, dendrites appeared and increased in concentration as the SOC increased. Dendrite morphology appeared to be dependent on whether the active material was on the “dull” or “shiny” side of the copper collector. Significantly more delamination of the active material from the collector was seen on themore » “shiny” side of the collector particularly at 180 and 250% SOC. Transition metals were detected at 120% SOC and increased in concentration as the SOC increased. Finally, there was considerable spatial heterogeneity in the microstructures across each laminate with several regions displaying complex layered structures.« less

Effect of overcharge on Li(Ni 0.5Mn 0.3Co 0.2)O 2/Graphite lithium ion cells with poly(vinylidene fluoride) binder. I - Microstructural changes in the anode

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dietz Rago, Nancy; Bareno, Javier; Li, Jianlin

Cells based on NMC/graphite, containing poly(vinylidene difluoride) (PVDF) binders in the positive and negative electrodes, were systematically overcharged to 100, 120, 140, 160, 180, and 250% state-of-charge (SOC). At 250% SOC the cell vented. Scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) of the anodes showed several state-of-overcharge-dependent trends. Starting at 120% SOC, dendrites appeared and increased in concentration as the SOC increased. Dendrite morphology appeared to be dependent on whether the active material was on the “dull” or “shiny” side of the copper collector. Significantly more delamination of the active material from the collector was seen on themore » “shiny” side of the collector particularly at 180 and 250% SOC. Transition metals were detected at 120% SOC and increased in concentration as the SOC increased. Finally, there was considerable spatial heterogeneity in the microstructures across each laminate with several regions displaying complex layered structures.« less

Enhancing analog performance and suppression of subthreshold swing using hetero-junctionless double gate TFETs

NASA Astrophysics Data System (ADS)

Chauhan, Sudakar Singh; Sharma, Neha

2017-12-01

This paper proposes hetero-junctionless double gate tunnel field effect transistor (HJLDG-TFETs) for suppression of subthreshold swing (SS) using an InAs compound semiconductor material. The proposed device with high dielectric material, gives an excellent performance when InAs uses at source side. Because of low band gap of 0.36 eV , it reduces the potential barrier height of source channel interface causing higher band to band tunneling. Whereas, Si at the drain side with higher band gap of 1.12 eV , increasing the barrier height of drain channel interface causing lower quantum tunneling. As a result, the proposed device with high-k (HfO2) at 30 nm channel section provides a tremendous characteristics with high ION /IOFF ratio of 2 ×1011 , a point SS of 43.30 mV / decade and moderate SS of 56.75 mV / decade . All the above results show that the proposed device is assured for a low power switching application. The variation in gate supply voltage also analyzed for transconductance property of the device.

Role of preemptive tapentadol in reduction of postoperative analgesic requirements after laparoscopic cholecystectomy

PubMed Central

Yadav, Ghanshyam; Jain, Gaurav; Samprathi, Abhishek; Baghel, Annavi; Singh, Dinesh Kumar

2016-01-01

Background and Aims: Poorly managed acute postoperative pain may result in prolonged morbidity. Various pharmacotherapies have targeted this, but research on an ideal preemptive analgesic continues, taking into account drug-related side effects. Considering the better tolerability profile of tapentadol, we assessed its role as a preemptive analgesic in the reduction of postoperative analgesic requirements, after laparoscopic cholecystectomy. Material and Methods: In a prospective-double-blinded fashion, sixty patients posted for above surgery, were randomized to receive tablet tapentadol 75 mg (Group A) or starch tablets (Group B) orally, an hour before induction of general anesthesia. Perioperative analgesic requirement, time to first analgesia, pain, and sedation score were compared for first 24 h during the postoperative period and analyzed by one-way analysis of variance test. A P < 0.05 was considered significant. Results: Sixty patients were analyzed. The perioperative analgesic requirement was significantly lower in Group A. Verbal numerical score was significantly lower in Group A at the time point, immediately after shifting the patient to the postanesthesia care unit. Ramsay sedation scores were similar between the groups. No major side effects were observed except for nausea and vomiting in 26 cases (10 in Group A, 16 in Group B). Conclusion: Single preemptive oral dose of tapentadol (75 mg) is effective in reducing perioperative analgesic requirements and acute postoperative pain, without added side effects. It could be an appropriate preemptive analgesic, subjected to future trials concentrating upon its dose-response effects. PMID:28096581

DOE Office of Scientific and Technical Information (OSTI.GOV)

Del Bianco, M.; Wiehagen, J.

This project evaluated the effectiveness and affordability of integrating retrofit insulated panels into a re-siding project. The Partnership for Home Innovation (PHI) teamed with New York State Energy Research and Development Authority (NYSERDA), the Albany Housing Authority (AHA), and the New York State Weatherization Assistance Program (WAP) administered by Albany Community Action Partnership to demonstrate an energy retrofit and siding upgrade on a two-story, seven unit, multifamily building in Albany New York (CZ 5). The project focused on accomplishing three goals - doubling the existing wall thermal resistance (from approximately R-13 to a weighted average of R-27), reduction of buildingmore » air leakage, and completion of the retrofit within a budget where the additional cost for upgrading wall's thermal resistance is equal to the cost of the standard re-siding effort (i.e., the total cost of the energy efficient re-siding scope of work is not more than double the cost of the standard re-siding effort). Lessons learned from the project strongly indicate that the retrofit panel technology can be installed using common installation practices and with minimal training. Other lessons learned include limitation on the use of standard air sealing materials during cold weather installations and the need to develop better installation guidance for trades working with the level of tolerances that may be present in the existing structure. This technology demonstration showed that exterior retrofit panels provide a viable and reasonable option for the siding trades to increase market opportunities and achieve synergistic benefits for aesthetic upgrades to a building's exterior.« less

Subjective Report of Side Effects of Prescribed and Nonprescribed Psychostimulant Use in Young Adults.

PubMed

Smith, Tess E; Martel, Michelle M; DeSantis, Alan D

2017-03-21

Side effects of prescribed and nonprescribed psychostimulant use are understudied. The study examined side effects of prescribed and nonprescribed psychostimulant use in a college sample with attention to possible gender differences. 2716 undergraduates (1448 male) between the ages of 17 and 57 years (M = 19.43 years, SD = 1.7 years) completed an online survey that included questions about the subjective side effects of prescribed and nonprescribed psychostimulant use. Results suggested that prescribed users more frequently reported side effects, compared to nonprescribed users. For prescribed users, females more frequently reported appetite, somatic, and anxiety-related side effects compared to males. For nonprescribed users, while females reported more somatic and anxiety-related side effects, males more frequently reported loss of sex drive and sweating as side effects. Conclusions/Importance: These findings suggest prescribed users of psychostimulants more frequently report side effects with prominent gender differences in line with gender roles.

Sexual side effects associated with conventional and atypical antipsychotics.

PubMed

Compton, M T; Miller, A H

2001-01-01

The sexual side effects of psychotropic medications are becoming increasingly recognized in clinical psychiatry. The magnitude of the problem of sexual side effects associated with antipsychotic medications has yet to be fully elucidated, but a multitude of references in the literature demonstrate the importance of these side effects in both men and women. All currently used antipsychotic medications are associated with sexual side effects of various types. Although each antipsychotic medication may have a specific side effect profile determined by its various receptor affinities and by the degree to which it elevates serum prolactin, there is currently no evidence that specific side effects can be predicted. Sexual side effects can be categorized according to the phase of the sexual response cycle with which they interfere. Suggestions for clinical evaluation and treatment options are provided, including risk factor modification, dose reduction, switching agents, and addition of other agents. Sexual side effects associated with conventional and atypical antipsychotic medications represent an underestimated and understudied set of side effects that may diminish a patient's quality of life and lead to treatment noncompliance. Clinicians prescribing antipsychotic medications should be familiar with the classification, evaluation, and treatment of these side effects.

Beyond spatial correlation effect in micro-Raman light scattering: An example of zinc-blende GaN/GaAs hetero-interface

NASA Astrophysics Data System (ADS)

Ning, J. Q.; Zheng, C. C.; Zheng, L. X.; Xu, S. J.

2015-08-01

Spatially resolved Raman light scattering experiments were performed on a zinc-blende GaN/GaAs heterostructure with confocal micro-Raman scattering technique under the backscattering geometric configuration. By varying the illumination spot locations across the heterostructure interface, we found that the Raman light scattering spectral features change remarkably. The interface effect on the GaAs substrate manifested as a much broader lineshape of the transverse optical (TO) phonon mode. Two kinds of broadening mechanisms, namely, spatial correlation induced wave-vector relaxation effect and lattice-mismatch strain + compositional intermixing effect, have been identified. The former leads to the broadening of the TO mode at the low-energy side, whereas the latter accounts for the broadening at the high-energy side. The diffuse light scattering from the highly defective nucleation layer of GaN was found to produce a broad scattering background of the GaN TO mode. The methodology and conclusions of the present work could be applicable to Raman spectroscopic studies on other material interfaces.

Synergistic Cytotoxicity Effect by Combination Treatment of Polyketide Derivatives from Annona muricata Linn Leaves and Doxorubicin as Potential Anticancer Material on Raji Cell Line

NASA Astrophysics Data System (ADS)

Artanti, A. N.; Astirin, O. P.; Prayito, A.; Fisma, R.; Prihapsara, F.

2018-03-01

Nasopharynx cancer is one of the most deadly cancer. The main priority of nasopharynx cancer treatment is the use of chemotherapeutic agents, especially doxorubicin. However, doxorubicin might also lead to diverse side effect. An approach recently develop to overcome side effect of doxorubicin is to used of combined chemotherapeutic agent. One of the compounds found effication as an anticancer agent on nasopharynx cancer is acetogenin, a polyketide compound that is abundant in Annona muricata L. leaves. This study has been done to examine polyketide derivatives was isolated from Annona muricata L. which has potency to induce apoptosis by p53 expression on raji cell line. The determination of cytotoxic combination activity from polyketide derivative and doxorubicin was evaluated using MTT assay to obtain the value of CI (combination index). Data analysis showed that combination of polyketide derivative from Annona muricata L. (14,4 µg/ml) and doxorubicin with all of concentration performed synergistic effect on raji cell line with CI value from 0.13 – 0.65.

New concept for treating female stress urinary incontinence with radiofrequency

PubMed Central

Lordelo, Patrícia; Boas, Andrea Vilas; Sodré, Danielle; Lemos, Amanda; Tozetto, Sibele; Brasil, Cristina

2017-01-01

ABSTRACT Purpose: To evaluate the clinical response and adverse effects of radiofrequency on the urethral meatus in the treatment of stress urinary incontinence in women. Materials and Methods: This phase one study included ten women with Stress Urinary Incontinence (SUI). The evaluation consisted of 1 hour Pad tests to quantify urine loss and to assess the degree of procedure satisfaction by using the Likert scale. To evaluate safety, we observed the number of referred side effects. Results: Average age was 53.10 years±7.08 years. In assessing the final Pad Test, 70% showed a reduction and 30% a worsening of urinary loss. Using the Pad Test one month later, there was a reduction in all patients (p=0.028). The degree of satisfaction was 90% and no side effects have been observed. One patient reported burning sensation. Conclusion: The treatment of SUI with radiofrequency on the urethral meatus has no adverse effects, being a low risk method that reduces urinary loss in women. However, to increase the validity of the study, larger clinical trials are warranted. PMID:28727373

[Subchondral drilling method combined with gum-bletilla complex to repair articular cartilage defects].

PubMed

Huang, Yong; Wang, Xin-Ling; Qiu, Heng; Xiao, Yi-Cheng; Wu, Zong-Hong; Xu, Jian

2018-02-01

Two types(A model and B model) of articular cartilage defect models were prepared by using adult New Zealand white rabbits. A model group was applied by drilling without through subchondral bone, whose right joint was repaired by composite scaffolds made by seed cell, gum-bletilla as well as Pluronic F-127, and left side was blank control. B model group was applied by subchondral drilling method, whose right joint was repaired by using composite scaffolds made by gum-bletilla and Pluronic F-127 without seed cells, and left side was blank control. Autogenous contrast was used in both model types. In addition, another group was applied with B model type rabbits, which was repaired with artificial complex material of Pluronic F-127 in both joint sides. 4, 12 and 24 weeks after operation, the animals were sacrificed and the samples were collected from repaired area for staining with HE, typeⅡcollagen immunohistochemical method, Alcian blue, and toluidine blue, and then were observed with optical microscope. Semi-quantitative scores were graded by referring to Wakitanis histological scoring standard to investigate the histomorphology of repaired tissue. Hyaline cartilage repairing was achieved in both Group A and Group B, with satisfactory results. There were no significant differences on repairing effects for articular cartilage defects between composite scaffolds made by seed cell, gum-bletilla and Pluronic F-127, and the composite scaffolds made by gum-bletilla and Pluronic F-127 without seed cell. Better repairing effects for articular cartilage defects were observed in groups with use of gum-bletilla, indicating that gum-bletilla is a vital part in composite scaffolds material. Copyright© by the Chinese Pharmaceutical Association.

Modelling cavitation erosion using fluid–material interaction simulations

PubMed Central

Chahine, Georges L.; Hsiao, Chao-Tsung

2015-01-01

Material deformation and pitting from cavitation bubble collapse is investigated using fluid and material dynamics and their interaction. In the fluid, a novel hybrid approach, which links a boundary element method and a compressible finite difference method, is used to capture non-spherical bubble dynamics and resulting liquid pressures efficiently and accurately. The bubble dynamics is intimately coupled with a finite-element structure model to enable fluid/structure interaction simulations. Bubble collapse loads the material with high impulsive pressures, which result from shock waves and bubble re-entrant jet direct impact on the material surface. The shock wave loading can be from the re-entrant jet impact on the opposite side of the bubble, the fast primary collapse of the bubble, and/or the collapse of the remaining bubble ring. This produces high stress waves, which propagate inside the material, cause deformation, and eventually failure. A permanent deformation or pit is formed when the local equivalent stresses exceed the material yield stress. The pressure loading depends on bubble dynamics parameters such as the size of the bubble at its maximum volume, the bubble standoff distance from the material wall and the pressure driving the bubble collapse. The effects of standoff and material type on the pressure loading and resulting pit formation are highlighted and the effects of bubble interaction on pressure loading and material deformation are preliminarily discussed. PMID:26442140

An Update to the NASA Reference Solar Sail Thrust Model

NASA Technical Reports Server (NTRS)

Heaton, Andrew F.; Artusio-Glimpse, Alexandra B.

2015-01-01

An optical model of solar sail material originally derived at JPL in 1978 has since served as the de facto standard for NASA and other solar sail researchers. The optical model includes terms for specular and diffuse reflection, thermal emission, and non-Lambertian diffuse reflection. The standard coefficients for these terms are based on tests of 2.5 micrometer Kapton sail material coated with 100 nm of aluminum on the front side and chromium on the back side. The original derivation of these coefficients was documented in an internal JPL technical memorandum that is no longer available. Additionally more recent optical testing has taken place and different materials have been used or are under consideration by various researchers for solar sails. Here, where possible, we re-derive the optical coefficients from the 1978 model and update them to accommodate newer test results and sail material. The source of the commonly used value for the front side non-Lambertian coefficient is not clear, so we investigate that coefficient in detail. Although this research is primarily designed to support the upcoming NASA NEA Scout and Lunar Flashlight solar sail missions, the results are also of interest to the wider solar sail community.

Mode trap for absorbing transverse modes of an accelerated electron beam

DOEpatents

Chojnacki, Eric P.

1994-01-01

A mode trap to trap and absorb transverse modes formed by a beam in a linear accelerator includes a waveguide having a multiplicity of electrically conductive (preferably copper) irises and rings, each iris and ring including an aperture, and the irises and rings being stacked in a side-by-side, alternating fashion such that the apertures of the irises and rings are concentrically aligned. An absorbing material layer such as a dielectric is embedded in each iris and ring, and this absorbing material layer encircles, but is circumferentially spaced from its respective aperture. Each iris and ring includes a plurality of circumferentially spaced slots around its aperture and extending radially out toward its absorbing material layer.

Radiation Insulation

NASA Technical Reports Server (NTRS)

1993-01-01

An aluminized polymer film is a highly effective radiation barrier for both manned and unmanned spacecraft. Variations of this space-devised material are also used as an energy conservation technique for homes and offices. One commercial company, Tech 2000 (formerly Buckeye Radiant Barrier), markets 'Super R' Radiant Barrier, which finds its origins in the Apollo Mission programs. The material is placed between wall studs and exterior facing before siding or in new roof installation, between roof support and roof sheathing. Successful retrofit installations have included schools and shrink wrap ovens. The radiant barrier blocks 95 percent of radiant energy, thus retaining summer heat and blocking winter cold. Suppliers claim utility bill reductions of 20 percent or more.

In vitro and in vivo evaluation of anti-cancer activity: Shape-dependent properties of TiO2 nanostructures.

PubMed

Sree Latha, T; Reddy, Madhava C; Muthukonda, Shankar V; Srikanth, Vadali V S S; Lomada, Dakshayani

2017-09-01

Cancer is a complex and widespread disease, and it is going to be the first cause of death in the world. Chemotherapy has been used to treat cancer, but it is detrimental to immune cells and known to induce numerous side effects. Therefore it is imperative to develop new drugs for the treatment of cancer without any side effects and toxicity. TiO 2 nanomaterials are human safe, cost effective, chemically stable and have numerous biomedical applications. Spherical TiO 2 fine particles (TFP), TiO 2 nanosquares (TNS) and TiO 2 nanotubes (TNT) were developed and evaluated for anti-cancer activity in vitro and in vivo. Our data suggest that these nanostructured materials significantly inhibited proliferation of breast cancer MDAMB 231 cells in in vitro shape dependent manner. In addition, we found that TiO 2 nanostructures inhibited the migration and colony formation of breast cancer MDAMB231 cells. More importantly, we found that TNS/TNT/TFP had anti-angiogenic effect in CAM assay and TNT had comparable anti-angiogenic effect with the positive control staurosporine. Additional qRT-PCR data suggest that TiO 2 nanostructures induced the upregulation of tumor suppressor genes p53, MDA7, TRAIL and transcription factor STAT3, which suggests the probable mechanism for the anticancer activity of TiO 2 nanostructures. Finally, analysis of TEM confirms the dispersion and interaction of nanostructures in the cells. Thus these materials could be potential therapeutic targets for the treatment of cancer. Copyright © 2017. Published by Elsevier B.V.

Thorium abundances of basalt ponds in South Pole-Aitken basin: Insights into the composition and evolution of the far side lunar mantle

USGS Publications Warehouse

Hagerty, Justin J.; Lawrence, D.J.; Hawke, B.R.

2011-01-01

Imbrian-aged basalt ponds, located on the floor of South Pole-Aitken (SPA) basin, are used to provide constraints on the composition and evolution of the far side lunar mantle. We use forward modeling of the Lunar Prospector Gamma Ray Spectrometer thorium data, to suggest that at least five different and distinct portions of the far side lunar mantle contain little or no thorium as of the Imbrian Period. We also use spatial correlations between local thorium enhancements and nonmare material on top of the basalt ponds to support previous assertions that lower crustal materials exposed in SPA basin have elevated thorium abundances, consistent with noritic to gabbronoritic lithologies. We suggest that the lower crust on the far side of the Moon experienced multiple intrusions of thorium-rich basaltic magmas, prior to the formation of SPA basin. The fact that many of the ponds on the lunar far side have elevated titanium abundances indicates that the far side of the Moon experienced extensive fractional crystallization that likely led to the formation of a KREEP-like component. However, because the Imbrian-aged basalts contain no signs of elevated thorium, we propose that the SPA impact event triggered the transport of a KREEP-like component from the lunar far side and concentrated it on the nearside of the Moon. Because of the correlation between basaltic ponds and basins within SPA, we suggest that Imbrian-aged basaltic volcanism on the far side of the Moon was driven by basin-induced decompressional melting.

Biodegradable nanoparticles for gene therapy technology

NASA Astrophysics Data System (ADS)

Hosseinkhani, Hossein; He, Wen-Jie; Chiang, Chiao-Hsi; Hong, Po-Da; Yu, Dah-Shyong; Domb, Abraham J.; Ou, Keng-Liang

2013-07-01

Rapid propagations in materials technology together with biology have initiated great hopes in the possibility of treating many diseases by gene therapy technology. Viral and non-viral gene carriers are currently applied for gene delivery. Non-viral technology is safe and effective for the delivery of genetic materials to cells and tissues. Non-viral systems are based on plasmid expression containing a gene encoding a therapeutic protein and synthetic biodegradable nanoparticles as a safe carrier of gene. Biodegradable nanoparticles have shown great interest in drug and gene delivery systems as they are easy to be synthesized and have no side effect in cells and tissues. This review provides a critical view of applications of biodegradable nanoparticles on gene therapy technology to enhance the localization of in vitro and in vivo and improve the function of administered genes.

Laser based imaging of time depending microscopic scenes with strong light emission

NASA Astrophysics Data System (ADS)

Hahlweg, Cornelius; Wilhelm, Eugen; Rothe, Hendrik

2011-10-01

Investigating volume scatterometry methods based on short range LIDAR devices for non-static objects we achieved interesting results aside the intended micro-LIDAR: the high speed camera recording of the illuminated scene of an exploding wire -intended for Doppler LIDAR tests - delivered a very effective method of observing details of objects with extremely strong light emission. As a side effect a schlieren movie is gathered without any special effort. The fact that microscopic features of short time processes with high emission and material flow might be imaged without endangering valuable equipment makes this technique at least as interesting as the intended one. So we decided to present our results - including latest video and photo material - instead of a more theoretical paper on our progress concerning the primary goal.

Method of Fabricating Double Sided Si(Ge)/Sapphire/III-Nitride Hybrid Structure

NASA Technical Reports Server (NTRS)

Choi, Sang Hyouk (Inventor); Park, Yeonjoon (Inventor)

2017-01-01

One aspect of the present invention is a double sided hybrid crystal structure including a trigonal Sapphire wafer containing a (0001) C-plane and having front and rear sides. The Sapphire wafer is substantially transparent to light in the visible and infrared spectra, and also provides insulation with respect to electromagnetic radio frequency noise. A layer of crystalline Si material having a cubic diamond structure aligned with the cubic <111> direction on the (0001) C-plane and strained as rhombohedron to thereby enable continuous integration of a selected (SiGe) device onto the rear side of the Sapphire wafer. The double sided hybrid crystal structure further includes an integrated III-Nitride crystalline layer on the front side of the Sapphire wafer that enables continuous integration of a selected III-Nitride device on the front side of the Sapphire wafer.

Double Sided Si(Ge)/Sapphire/III-Nitride Hybrid Structure

NASA Technical Reports Server (NTRS)

Park, Yeonjoon (Inventor); Choi, Sang Hyouk (Inventor)

2016-01-01

One aspect of the present invention is a double sided hybrid crystal structure including a trigonal Sapphire wafer containing a (0001) C-plane and having front and rear sides. The Sapphire wafer is substantially transparent to light in the visible and infrared spectra, and also provides insulation with respect to electromagnetic radio frequency noise. A layer of crystalline Si material having a cubic diamond structure aligned with the cubic <111> direction on the (0001) C-plane and strained as rhombohedron to thereby enable continuous integration of a selected (SiGe) device onto the rear side of the Sapphire wafer. The double sided hybrid crystal structure further includes an integrated III-Nitride crystalline layer on the front side of the Sapphire wafer that enables continuous integration of a selected III-Nitride device on the front side of the Sapphire wafer.

A Literature and Records Search on the Cultural Resources of the Portage, Wisconsin Area

DTIC Science & Technology

1980-08-01

brother , A.W. English) of Wyocena. Mr. English, a high. school teacher, appeared to have been the most active...north side of the highway to Dekorra, on both banks of Rocky Run Creek Investigator/Year: Brown, 1937 Report/Reference: Brown Manuscripts, 9/19/37...sides of the creek . On the east side, a limited amount of material was recovered. However, across the creek , a larger number of artifacts were

Study of Microstructure and Mechanical Properties Effects on Workpiece Quality in Sheet Metal Extrusion Process

PubMed Central

Suriyapha, Chatkaew; Bubphachot, Bopit; Rittidech, Sampan

2015-01-01

Sheet metal extrusion is a metal forming process in which the movement of a punch penetrates a sheet metal surface and it flows through a die orifice; the extruded parts can be deflected to have an extrusion cavity and protrusion on the opposite side. Therefore, this process results in a narrow region of highly localized plastic deformation due to the formation and microstructure effect on the work piece. This research investigated the characteristics of the material-flow behavior during the formation and its effect on the microstructure of the extruded sheet metal using the finite element method (FEM). The actual parts and FEM simulation model were developed using a blank material made from AISI-1045 steel with a thickness of 5 mm; the material's behavior was determined subject to the punch penetration depths of 20%, 40%, 60%, and 80% of the sheet thickness. The results indicated the formation and microstructure effects on the sheet metal extrusion parts and defects. Namely, when increasing penetration, narrowing the die orifice the material flows through, the material was formed by extruding, and defects were visibility, and the microstructure of the material's grains' size was flat and very fine. Extrusion defects were not found in the control material flow. The region of highly localized plastic deformation affected the material gain and mechanical properties. The FEM simulation results agreed with the experimental results. Moreover, FEM could be investigated as a tool to decrease the cost and time in trial and error procedures. PMID:26229979

Research on the Stress and Material Flow with Single Particle—Simulations and Experiments

NASA Astrophysics Data System (ADS)

Zhang, Tao; Jiang, Feng; Yan, Lan; Xu, Xipeng

2017-04-01

The scratching process of particle is a complex material removal process involving cutting, plowing, and rubbing. In this study, scratch experiments under different loads are performed on a multifunctional tester for material surface. Natural diamond and Fe-Cr-Ni stainless steel are chosen as indenter and workpiece material, respectively. The cutting depth and side flow height of scratch are measured using a white light interferometer. The finite element model is developed, and the numerical simulation of scratching is conducted using AdvantEdgeTM. The simulated forces and side flow height under different cutting depths correspond well with experimental results, validating the accuracy of the scratching simulation. The mises stress distribution of the particle is presented, with the maximum stress occurring inside the particle rather than on the surface. The pressure distribution of the particle is also given, and results show that the maximum pressure occurs on the contact surface of particle and workpiece. The material flow contour is presented, and material flow direction and velocity magnitude are analyzed.

Gastrointestinal Side Effects of Antiarrhythmic Medications: A Review of Current Literature.

PubMed

Amjad, Waseem; Qureshi, Waqas; Farooq, Ali; Sohail, Umair; Khatoon, Salma; Pervaiz, Sarah; Narra, Pratyusha; Hasan, Syeda M; Ali, Farman; Ullah, Aman; Guttmann, Steven

2017-09-03

Antiarrhythmic drugs are commonly prescribed cardiac drugs. Due to their receptor mimicry with several of the gastrointestinal tract receptors, they can frequently lead to gastrointestinal side effects. These side effects are the most common reasons for discontinuation of these drugs by the patients. Knowledge of these side effects is important for clinicians that manage antiarrhythmic drugs. This review focuses on the gastrointestinal side effects of these drugs and provides a detailed up-to-date literature review of the side effects of these drugs. The review provides case reports reported in the literature as well as possible mechanisms that lead to gastrointestinal side effects.

46 CFR 45.3 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-10-01

... with no openings. (r) Steel means steel and materials with which structures can be made equivalent to steel with respect to such parameters as yield strength, total deflection, flexural life, or resistance.... (i) Superstructure means a deck structure on the freeboard deck, extending from side to side of the...

Technique for controlling shrinkage distortion in cold-pressed annular pellets

DOEpatents

Johnson, R.G.R.; Burke, T.J.

1982-06-28

A process and apparatus are described for the production of annular fuel pellets comprising locating particulate fuel material in a compaction chamber having side walls, a moveable punch located opposite a fixed member and a frustoconical element having a taper of between about 0.010 to 0.015 inches/inch located in about the center of the chamber. The punch is moved toward the fixed surface to compact the particulate material. The compacted pellet is fired to produce sintered pellets having substantially straight inner side walls essentially parallel to the pellet axis.

Memory for Medication Side Effects in Younger and Older Adults: The Role of Subjective and Objective Importance

PubMed Central

Friedman, Michael C.; McGillivray, Shannon; Murayama, Kou; Castel, Alan D.

2014-01-01

Older adults often experience memory impairments, but can sometimes use selective processing and schematic support to remember important information. The current experiments investigate to what degree younger and healthy older adults remember medication side effects that were subjectively or objectively important to remember. Participants studied a list of common side effects, and rated how negative these effects were if they were to experience them, and were then given a free recall test. In Experiment 1, the severity of the side effects ranged from mild (e.g., itching) to severe (e.g., stroke), and in Experiment 2, certain side effects were indicated as critical to remember (i.e., “contact your doctor if you experience this”). There were no age differences in terms of free recall of the side effects, and older adults remembered more severe side effects relative to mild effects. However, older adults were less likely to recognize critical side effects on a later recognition test, relative to younger adults. The findings suggest that older adults can selectively remember medication side effects, but have difficulty identifying familiar but potentially critical side effects, and this has implications for monitoring medication use in older age. PMID:25331278

Artificial reef effect in relation to offshore renewable energy conversion: state of the art.

PubMed

Langhamer, Olivia

2012-01-01

The rapid worldwide growth of offshore renewable energy production will provide marine organisms with new hard substrate for colonization, thus acting as artificial reefs. The artificial reef effect is important when constructing, for example, scour protections since it can generate an enhanced habitat. Specifically, artificial structures can create increased heterogeneity in the area important for species diversity and density. Offshore energy installations also have the positive side effect as they are a sanctuary area for trawled organisms. Higher survival of fish and bigger fish is an expected outcome that can contribute to a spillover to outer areas. One negative side effect is that invasive species can find new habitats in artificial reefs and thus influence the native habitats and their associated environment negatively. Different scour protections in offshore wind farms can create new habitats compensating for habitat loss by offshore energy installations. These created habitats differ from the lost habitat in species composition substantially. A positive reef effect is dependent on the nature and the location of the reef and the characteristics of the native populations. An increase in surface area of scour protections by using specially designed material can also support the reef effect and its productivity.

Artificial Reef Effect in relation to Offshore Renewable Energy Conversion: State of the Art

PubMed Central

2012-01-01

The rapid worldwide growth of offshore renewable energy production will provide marine organisms with new hard substrate for colonization, thus acting as artificial reefs. The artificial reef effect is important when constructing, for example, scour protections since it can generate an enhanced habitat. Specifically, artificial structures can create increased heterogeneity in the area important for species diversity and density. Offshore energy installations also have the positive side effect as they are a sanctuary area for trawled organisms. Higher survival of fish and bigger fish is an expected outcome that can contribute to a spillover to outer areas. One negative side effect is that invasive species can find new habitats in artificial reefs and thus influence the native habitats and their associated environment negatively. Different scour protections in offshore wind farms can create new habitats compensating for habitat loss by offshore energy installations. These created habitats differ from the lost habitat in species composition substantially. A positive reef effect is dependent on the nature and the location of the reef and the characteristics of the native populations. An increase in surface area of scour protections by using specially designed material can also support the reef effect and its productivity. PMID:23326215

Simultaneous sinus lift and implantation using platelet-rich fibrin as sole grafting material.

PubMed

Jeong, Seung-Mi; Lee, Chun-Ui; Son, Jeong-Seog; Oh, Ji-Hyeon; Fang, Yiqin; Choi, Byung-Ho

2014-09-01

Recently, several authors have shown that simultaneous sinus lift and implantation using autologous platelet-rich fibrin as the sole filling material is a reliable procedure promoting bone augmentation in the maxillary sinus. The aim of this study was to examine the effect of simultaneous sinus lift and implantation using platelet-rich fibrin as the sole grafting material on bone formation in a canine sinus model. An implant was placed after sinus membrane elevation in the maxillary sinus of six adult female mongrel dogs. The resulting space between the membrane and sinus floor was filled with autologous platelet-rich fibrin retrieved from each dog. The implants were left in place for six months. Bone tissue was seen at the lower part of the implants introduced into the sinus cavity. The height of the newly formed bone around the implants ranged from 0 mm to 4.9 mm (mean; 2.6 ± 2.0 mm) on the buccal side and from 0 mm to 4.2 mm (mean; 1.3 ± 1.8 mm) on the palatal side. The findings from this study suggest that simultaneous sinus lift and implantation using platelet-rich fibrin as sole grafting material is not a predictable and reproducible procedure, especially with respect to the bone formation around the implants in the sinus cavity. Copyright © 2014 European Association for Cranio-Maxillo-Facial Surgery. All rights reserved.

Modulations of Foot and Ankle Frontal Kinematics for Breaking and Propulsive Movement Characteristics during Side-Step Cutting with Varying Midsole Thicknesses

PubMed Central

Lin, Yi-Jia; Lee, Shih-Chi; Chang, Chao-Chin; Liu, Tsung-Han

2018-01-01

This study is aimed at determining the effects of midsole thickness on movement characteristic during side cutting movement. Fifteen athletes performed side-step cutting while wearing shoes with varying midsole thicknesses. Temporal-spatial and ground reaction force variables as well as foot and ankle frontal kinematics were used to describe breaking and propulsive movement characteristics and modulation strategies. Regardless of midsole thickness, temporal-spatial variables and breaking and propulsive force during side cutting were statistically unchanged. Significantly greater peaks of ankle inversion and plantarflexion with a thicker sole and greater midtarsal pronation with a thinner sole were observed. Current results demonstrated that hypotheses formed solely based on material testing were insufficient to understand the adaptations in human movement because of the redundancy of the neuromusculoskeletal system. Participants were able to maintain temporal-spatial performance during side cutting while wearing shoes with midsoles of varying thicknesses. Increased pronation for a thinner sole might help reduce the force of impact but might be associated with an increased risk of excessive stress on soft tissue. Increased peak of ankle inversion and plantarflexion for a thicker sole may be unfavorable for the stability of ankle joint. Information provided in human movement testing is crucial for understanding factors associated with movement characteristics and injury and should be considered in the future development of shoe design. PMID:29854000

“So far it’s been choosing which side effects I want or I can deal with”: A grounded theory of HIV treatment side effects among people living with HIV

PubMed Central

Holmes, Dave

2016-01-01

Despite the availability of new antiretroviral drugs and the simplification of treatment options, side effects continue to affect people living with HIV. In this paper, we present the findings of a grounded theory study designed to gain a critical understanding of the experience of side effects. Three main categories emerged from the data: the side effects, the experience, and the connections. The first category suggests that we need to change how we think about side effects in order to take into account the context in which they are experienced as well as the types and nature of side effects. The second category puts forward the idea that the experience of side effects is composed of three interrelated processes: becoming with, living with, and dealing with. Finally, the third category points to new connections that are formed with people, things and systems in the presence of side effects. PMID:27867446

Double sided grating fabrication for high energy X-ray phase contrast imaging

DOE PAGES

Hollowell, Andrew E.; Arrington, Christian L.; Finnegan, Patrick; ...

2018-04-19

State of the art grating fabrication currently limits the maximum source energy that can be used in lab based x-ray phase contrast imaging (XPCI) systems. In order to move to higher source energies, and image high density materials or image through encapsulating barriers, new grating fabrication methods are needed. In this work we have analyzed a new modality for grating fabrication that involves precision alignment of etched gratings on both sides of a substrate, effectively doubling the thickness of the grating. Furthermore, we have achieved a front-to-backside feature alignment accuracy of 0.5 µm demonstrating a methodology that can be appliedmore » to any grating fabrication approach extending the attainable aspect ratios allowing higher energy lab based XPCI systems.« less

Double sided grating fabrication for high energy X-ray phase contrast imaging

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hollowell, Andrew E.; Arrington, Christian L.; Finnegan, Patrick

State of the art grating fabrication currently limits the maximum source energy that can be used in lab based x-ray phase contrast imaging (XPCI) systems. In order to move to higher source energies, and image high density materials or image through encapsulating barriers, new grating fabrication methods are needed. In this work we have analyzed a new modality for grating fabrication that involves precision alignment of etched gratings on both sides of a substrate, effectively doubling the thickness of the grating. Furthermore, we have achieved a front-to-backside feature alignment accuracy of 0.5 µm demonstrating a methodology that can be appliedmore » to any grating fabrication approach extending the attainable aspect ratios allowing higher energy lab based XPCI systems.« less

Relation between therapeutic response and side effects induced by methylphenidate as observed by parents and teachers of children with ADHD.

PubMed

Lee, James; Grizenko, Natalie; Bhat, Venkataramana; Sengupta, Sarojini; Polotskaia, Anna; Joober, Ridha

2011-04-21

The desired (therapeutic) and undesired (side) effects of methylphenidate might have underlying correlations. The aim of this study was to explore the strength and the possible sources of these correlations. One hundred and fifty-seven children with ADHD (6-12 years) were administered placebo and methylphenidate (0.5 mg/kg in a divided b.i.d. dose), each for a one-week period, in a double-blind, crossover trial. Therapeutic response was assessed using the Conners' Global Index for parents (CGI-Parents) and teachers (CGI-Teachers), while side effects were assessed using the Barkley Side Effects Rating Scale (SERS). The side effect profile as assessed by the SERS was similar to that of previous studies with insomnia, decreased appetite, and headaches showing significant treatment effects (p < 0.005). These "somatic/physical" side effects did not correlate with CGI-Parents or CGI-Teachers. However, the side effects of "irritability", "proneness to crying", and "anxiousness" showed significant relationships with CGI-Parents. These "mood/anxiety" side effects showed no significant correlations with the CGI-Teachers. The greater "mood/anxiety" side effects on methylphenidate and placebo, the less the parents observe improvement of their children while treated with methylphenidate. This suggests that the correlations between "mood/anxiety" side effects and poor response to treatment may be driven by observer effects rather than biological commonalities between therapeutic and side effects of methylphenidate.

Assessment of the Impact of the California Water Project in the West Side of the San Joaquin Valley

NASA Technical Reports Server (NTRS)

Estes, J. E.; Kuhn, M.; Golomb, B.; Senger, L. W.; Wester, L.; Fortune, P.; Viellenave, J.

1971-01-01

The ability of remote sensing techniques to effectively monitor, on a continuing basis, the impact of a change in the water supply of an arid area is considered. Research involves the collection of a substantial body of information relative to both physical and biological phenomena or systems operative within the study area by concentrating on the accumulation of library materials, and field data.

Conference on Semi-Insulating III-V Materials (2nd), held 19-21 Apr 82, Evian (France),

DTIC Science & Technology

1983-02-28

Dist Special 19. KEY WORDS (Continue on reverse side If neceary mud Identity by block numb ) Semiconductor devices Field effect transitors Integrated...doped GaAs sub- 4 strates. The results showed no The catalog of defects includes statistically significant differ- vacancies, interstitials, anti...orientation also had high level profiles of GaAs active transconductance. In addition,the statistical scatter-uni-layers and their correlation to o m

Low-Loss Materials for Josephson Qubits

DTIC Science & Technology

2014-10-09

quantum circuit. It also intuitively explains how for a linear circuit the standard results for electrical circuits are obtained, justifying the use of... linear concepts for a weakly non- linear device such as the transmon. It has also become common to use a double sided noise spectrum to represent...loss tangent of large area pad junction. (c) Effective linearized circuit for the double junction, which makes up the admittance $Y$. $L_j$ is the

An analysis of innovation in materials and energy

NASA Astrophysics Data System (ADS)

Connelly, Michael

This dissertation presents an analysis of innovation in engineering materials and energy sources. More than fifty engineering materials and fourteen energy sources were selected for an evaluation of the relationship between the yearly production activity and yearly patent counts, which may be considered as a measure of innovation, for each. Through the employment of correlation theory, best-fit and origin shift analyses, it has been determined here that engineering materials and energy sources display similar life cycle and innovative activity behaviors. Correlation theory revealed a relationship between the yearly production and yearly patent counts indicating the extent that production and innovation affect each other. Best-fit analysis determined that four-stage life cycles exist for both engineering materials (metals and non-metals) and energy sources. Correlation and best-fit indicators of an estimated Stage III are confirmed by the presence of an origin shift of the patent data when compared to the production data which indicates that patents, or innovation, are driving, or being driven by, production. This driving force could represent the constructive or destructive side of the innovative process, with such sides being delineated by a possible universal constant above which there is destructive innovative behavior and below which exists constructive innovation. The driving force may also illustrate the manner in which an engineering material or energy source transitions into an innovatively less active state, enter Stage IV and possibly become a commodity. A possible Stage V, indicating "Final Death", is introduced in which production is on a steep decline with no signs of recovery. Additionally, innovatively active energy sources are often found to utilize or be supported by innovatively active engineering materials. A model is presented that can be used for the evaluation of innovation and production that can be applied to both engineering materials and energy sources that may be used to predict the innovative behavior of these resources in order that they can be more effectively allocated and utilized.

Side Effects

Cancer.gov

Side effects are problems that occur when cancer treatment affects healthy tissues or organs. Learn about side effects caused by cancer treatment. Know what signs and symptoms to call your doctor about. Learn about treatments for side effects.

Nanoparticles: pharmacological and toxicological significance

PubMed Central

Medina, C; Santos-Martinez, M J; Radomski, A; Corrigan, O I; Radomski, M W

2007-01-01

Nanoparticles are tiny materials (<1000 nm in size) that have specific physicochemical properties different to bulk materials of the same composition and such properties make them very attractive for commercial and medical development. However, nanoparticles can act on living cells at the nanolevel resulting not only in biologically desirable, but also in undesirable effects. In contrast to many efforts aimed at exploiting desirable properties of nanoparticles for medicine, there are limited attempts to evaluate potentially undesirable effects of these particles when administered intentionally for medical purposes. Therefore, there is a pressing need for careful consideration of benefits and side effects of the use of nanoparticles in medicine. This review article aims at providing a balanced update of these exciting pharmacological and potentially toxicological developments. The classes of nanoparticles, the current status of nanoparticle use in pharmacology and therapeutics, the demonstrated and potential toxicity of nanoparticles will be discussed. PMID:17245366

A new biphasic osteoinductive calcium composite material with a negative Zeta potential for bone augmentation

PubMed Central

Smeets, Ralf; Kolk, Andreas; Gerressen, Marcus; Driemel, Oliver; Maciejewski, Oliver; Hermanns-Sachweh, Benita; Riediger, Dieter; Stein, Jamal M

2009-01-01

The aim of the present study was to analyze the osteogenic potential of a biphasic calcium composite material (BCC) with a negative surface charge for maxillary sinus floor augmentation. In a 61 year old patient, the BCC material was used in a bilateral sinus floor augmentation procedure. Six months postoperative, a bone sample was taken from the augmented regions before two titanium implants were inserted at each side. We analyzed bone neoformation by histology, bone density by computed tomography, and measured the activity of voltage-activated calcium currents of osteoblasts and surface charge effects. Control orthopantomograms were carried out five months after implant insertion. The BCC was biocompatible and replaced by new mineralized bone after being resorbed completely. The material demonstrated a negative surface charge (negative Zeta potential) which was found to be favorable for bone regeneration and osseointegration of dental implants. PMID:19523239

South Pole-Aitken Sample Return Mission: Collecting Mare Basalts from the Far Side of the Moon

NASA Technical Reports Server (NTRS)

Gillis, J. J.; Jolliff, B. L.; Lucey, P. G.

2003-01-01

We consider the probability that a sample mission to a site within the South Pole-Aitken Basin (SPA) would return basaltic material. A sample mission to the SPA would be the first opportunity to sample basalts from the far side of the Moon. The near side basalts are more abundant in terms of volume and area than their far-side counterparts (16:1), and the basalt deposits within SPA represent approx. 28% of the total basalt surface area on the far side. Sampling far-side basalts is of particular importance because as partial melts of the mantle, they could have derived from a mantle that is mineralogically and chemically different than determined for the nearside, as would be expected if the magma ocean solidified earlier on the far side. For example, evidence to support the existence of high-Th basalts like those that appear to be common on the nearside in the Procellarum KREEP Terrane has been found. Although SPA is the deepest basin on the Moon, it is not extensively filled with mare basalt, as might be expected if similar amounts of partial melting occurred in the mantle below SPA as for basins on the near side. These observations may mean that mantle beneath the far-side crust is lower in Th and other heat producing elements than the nearside. One proposed location for a sample-return landing site is 60 S, 160 W. This site was suggested to maximize the science return with respect to sampling crustal material and SPA impact melt, however, basaltic samples would undoubtedly occur there. On the basis of Apollo samples, we should expect that basaltic materials would be found in the vicinity of any landing site within SPA, even if located away from mare deposits. For example, the Apollo 16 mission landed in an ancient highlands region 250-300 km away from the nearest mare-highlands boundary yet it still contains a small component of basaltic samples (20 lithic fragments ranging is size from <1 to .01 cm). A soil sample from the floor of SPA will likely contain an assortment of basaltic fragments from surrounding regions. In terms both of selecting the best landing sites and understanding the geologic context for returned samples, it is important to understand the compositional distribution of basalts within SPA basin.

Production of an ion-exchange membrane-catalytic electrode bonded material for electrolytic cells

NASA Technical Reports Server (NTRS)

Takenaka, H.; Torikai, E.

1986-01-01

A good bond is achieved by placing a metal salt in solution on one side of a membrane and a reducing agent on the other side so that the reducing agent penetrates the membrane and reduces the metal. Thus, a solution containing Pt, Rh, etc., is placed on one side of the membrane and a reducing agent such as NaBH, is placed on the other side. The bonded metal layer obtained is superior in catalytic activity and is suitable as an electrode in a cell such as for solid polymer electrolyte water electrolysis.

Lensing duct

DOEpatents

Beach, R.J.; Benett, W.J.

1994-04-26

A lensing duct to condense (intensify) light using a combination of front surface lensing and reflective waveguiding is described. The duct tapers down from a wide input side to a narrow output side, with the input side being lens-shaped and coated with an antireflective coating for more efficient transmission into the duct. The four side surfaces are uncoated, preventing light from escaping by total internal reflection as it travels along the duct (reflective waveguiding). The duct has various applications for intensifying light, such as in the coupling of diode array pump light to solid state lasing materials, and can be fabricated from inexpensive glass and plastic. 3 figures.

Fabrication of Lanthanum Telluride 14-1-11 Zintl High-Temperature Thermoelectric Couple

NASA Technical Reports Server (NTRS)

Ravi, Vilupanur A.; Li, Billy Chun-Yip; Fleurial, Pierre; Star, Kurt

2010-01-01

The development of more efficient thermoelectric couple technology capable of operating with high-grade heat sources up to 1,275 K is key to improving the performance of radioisotope thermoelectric generators. Lanthanum telluride La3-xTe4 and 14-1-11 Zintls (Yb14MnSb11) have been identified as very promising materials. The fabrication of advanced high-temperature thermoelectric couples requires the joining of several dissimilar materials, typically including a number of diffusion bonding and brazing steps, to achieve a device capable of operating at elevated temperatures across a large temperature differential (up to 900 K). A thermoelectric couple typically comprises a heat collector/ exchanger, metallic interconnects on both hot and cold sides, n-type and ptype conductivity thermoelectric elements, and cold-side hardware to connect to the cold-side heat rejection and provide electrical connections. Differences in the physical, mechanical, and chemical properties of the materials that make up the thermoelectric couple, especially differences in the coefficients of thermal expansion (CTE), result in undesirable interfacial stresses that can lead to mechanical failure of the device. The problem is further complicated by the fact that the thermoelectric materials under consideration have large CTE values, are brittle, and cracks can propagate through them with minimal resistance. The inherent challenge of bonding brittle, high-thermal-expansion thermoelectric materials to a hot shoe material that is thick enough to carry the requisite electrical current was overcome. A critical advantage over prior art is that this device was constructed using all diffusion bonds and a minimum number of assembly steps. The fabrication process and the materials used are described in the following steps: (1) Applying a thin refractory metal foil to both sides of lanthanum telluride. To fabricate the n-type leg of the advanced thermoelectric couple, the pre-synthesized lanthanum telluride coupon was diffusion bonded to the metal foil using a thin adhesion layer. (2) Repeating a similar process for the 14-1-11 Zintl p-type leg of the advanced thermoelectric couple. (3) Bonding thick CTE-matched metal plates on the metallized lanthanum telluride and Yb14MnSb11 to form the hot and cold sides of the thermoelectric couple. The calculated conversion efficiency of such an advanced couple would be about 10.5 percent, about 35 percent better than heritage radioisotope thermoelectric technology that relies on Si-Ge alloys. In addition, unlike Si-Ge alloys, these materials can be combined with many other thermoelectric materials optimized for operation at lower temperatures to achieve conversion efficiency in excess of 15 percent (a factor of 2 increase over heritage technology).

46 CFR 169.545 - Markings.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 7 2014-10-01 2014-10-01 false Markings. 169.545 Section 169.545 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) NAUTICAL SCHOOLS SAILING SCHOOL VESSELS Lifesaving and... material attached on its front side and at least 200 sq. cm. on its back side. If the personal flotation...

46 CFR 169.545 - Markings.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 7 2012-10-01 2012-10-01 false Markings. 169.545 Section 169.545 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) NAUTICAL SCHOOLS SAILING SCHOOL VESSELS Lifesaving and... material attached on its front side and at least 200 sq. cm. on its back side. If the personal flotation...

46 CFR 169.545 - Markings.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 7 2011-10-01 2011-10-01 false Markings. 169.545 Section 169.545 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) NAUTICAL SCHOOLS SAILING SCHOOL VESSELS Lifesaving and... material attached on its front side and at least 200 sq. cm. on its back side. If the personal flotation...

46 CFR 169.545 - Markings.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Markings. 169.545 Section 169.545 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) NAUTICAL SCHOOLS SAILING SCHOOL VESSELS Lifesaving and... material attached on its front side and at least 200 sq. cm. on its back side. If the personal flotation...

46 CFR 169.545 - Markings.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 7 2013-10-01 2013-10-01 false Markings. 169.545 Section 169.545 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) NAUTICAL SCHOOLS SAILING SCHOOL VESSELS Lifesaving and... material attached on its front side and at least 200 sq. cm. on its back side. If the personal flotation...

Microgravity

NASA Image and Video Library

2004-04-15

The Advanced Gradient Heating Facility (AGHF) is a European Space Agency (ESA) developed hardware. The AGHF was flown on STS-78, which featured four European PI's and two NASA PI's. The AGHFsupports the production of advanced semiconductor materials and alloys using the directional process, which depends on establishing a hot side and a cold side in the sample.

ETR HEAT EXCHANGER BUILDING, TRA644. DETAIL OF SOUTH SIDE BUILDING ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

ETR HEAT EXCHANGER BUILDING, TRA-644. DETAIL OF SOUTH SIDE BUILDING INSET. DEMINERALIZER WING AT RIGHT. CAMERA FACING NORTH. INL NEGATIVE NO. HD46-36-2. Mike Crane, Photographer, 4/2005 - Idaho National Engineering Laboratory, Test Reactor Area, Materials & Engineering Test Reactors, Scoville, Butte County, ID

Topic Centred Subject/Language Learning Materials and Their Use.

ERIC Educational Resources Information Center

Rado, Marta

Social bilinguals (second language learners in a linguistic minority) and cultural bilinguals (foreign language learners) often learn side by side in the same classroom, making syllabus planning and choice of teaching methodology difficult. Adopting a bilingual approach and exploring the semantic and discourse aspects of language can overcome the…

Rock Cycle Roulette.

ERIC Educational Resources Information Center

Schmidt, Stan M.; Palmer, Courtney

2000-01-01

Introduces an activity on the rock cycle. Sets 11 stages representing the transitions of an earth material in the rock cycle. Builds six-sided die for each station, and students move to the stations depending on the rolling side of the die. Evaluates students by discussing several questions in the classroom. Provides instructional information for…

Visual Juxtaposition as Qualitative Inquiry in Educational Research

ERIC Educational Resources Information Center

Metcalfe, Amy Scott

2015-01-01

Visual juxtaposition is inquiry through contrast, facilitated by side-by-side positioning of two images, or images and text. When combined with a theoretical foundation that explores interactions between the material and discursive elements of visual data, juxtaposition creates opportunities for qualitative analysis that are not as readily…

Nearly Seamless Vacuum-Insulated Boxes

NASA Technical Reports Server (NTRS)

Stepanian, Christopher J.; Ou, Danny; Hu, Xiangjun

2010-01-01

A design concept, and a fabrication process that would implement the design concept, have been proposed for nearly seamless vacuum-insulated boxes that could be the main structural components of a variety of controlled-temperature containers, including common household refrigerators and insulating containers for shipping foods. In a typical case, a vacuum-insulated box would be shaped like a rectangular parallelepiped conventional refrigerator box having five fully closed sides and a hinged door on the sixth side. Although it is possible to construct the five-closed-side portion of the box as an assembly of five unitary vacuum-insulated panels, it is not desirable to do so because the relatively high thermal conductances of the seams between the panels would contribute significant amounts of heat leakage, relative to the leakage through the panels themselves. In contrast, the proposal would make it possible to reduce heat leakage by constructing the five-closed-side portion of the box plus the stationary portion (if any) of the sixth side as a single, seamless unit; the only remaining seam would be the edge seal around the door. The basic cross-sectional configuration of each side of a vacuum-insulated box according to the proposal would be that of a conventional vacuum-insulated panel: a low-density, porous core material filling a partially evacuated space between face sheets. However, neither the face sheets nor the core would be conventional. The face sheets would be opposite sides of a vacuum bag. The core material would be a flexible polymer-modified silica aerogel of the type described in Silica/Polymer and Silica/Polymer/Fiber Composite Aero - gels (MSC-23736) in this issue of NASA Tech Briefs. As noted in that article, the stiffness of this core material against compression is greater than that of prior aerogels. This is an important advantage because it translates to greater retention of thickness and, hence, of insulation performance when pressure is applied across the thickness, in particular, when the space between the face sheets is evacuated, causing the core material to be squeezed between the face sheets by atmospheric pressure. Fabrication of a typical vacuum-insulated box according to the proposal would begin with fabrication of a cross-shaped polymer-modified aerogel blanket. The dimensions of the cross would be chosen so that (1) the central rectangular portion of the cross would form the core for the back of the box and (2) the arms of the cross could be folded 90 from the back plane to form the cores of the adjacent four sides of the box. Optionally, the blanket could include tabs for joining the folded sides of the blanket along mating edges and tabs that could serve as hinges for the door. Vacuum bags in the form of similar five-sided boxes would be made of a suitable polymeric film, one bag to fit the outer core surface, the other to fit the inner core surface. By use of commercially available film-sealing equipment, these box-shaped bags would be seamed together to form a single vacuum bag encasing the box-shaped core. Also, a one-way valve would be sealed to the bag. Through this valve, the interior of the bag would be evacuated to a pressure between 1 and 10 torr (approximately between 0.13 and 1.3 kPa). The polymer-modified aerogel core material is known to perform well as a thermal insulator in such a partial vacuum.

Side Effects of HIV Medicines: HIV and Lactic Acidosis

MedlinePlus

... Drugs Clinical Trials Apps skip to content Side Effects of HIV Medicines Home Understanding HIV/AIDS Fact ... and Immunizations What is a Drug Interaction? Side Effects of HIV Medicines HIV Medicines and Side Effects ...

Spontaneously Combustible Solids -- A Literature Search

DTIC Science & Technology

1975-05-01

Wasahizeon, D.* C. It. K(EY WORDS (Continue on reviers side It necesary and Identify by block number) Pyrophoric Materials Hazardous Materials...and Identify by block number) Existing information on spontaneously combustible solids including pyrophoric - air hazardous materials and water... pyrophoric -air hazardous and water reactive materials. All available hazard classification systems and test methods releting to spontaneous combustion have

Heat transfer in composite materials disintegrating under high-rate one-sided heating

NASA Astrophysics Data System (ADS)

Isaev, K. B.

1993-12-01

A mathematical model of heat transfer in heat-protective materials is suggested with the proviso of a squarelaw temperature depence of the material density in the zone of thermal destruction of its binder. The influence of certain factors on the experimental temperature field and thermal conductivity of a glass-reinforced epoxy plastic material is shown.

Framing effects on expectations, decisions, and side effects experienced: the case of influenza immunization.

PubMed

O'Connor, A M; Pennie, R A; Dales, R E

1996-11-01

To examine the effects of using positive or negative frames to describe influenza vaccine benefits and side effects on patients' expectations, decisions, decisional conflict, and reported side effects. 292 previously unimmunized patients with chronic respiratory or cardiac disease were randomly assigned to receive benefit/risk information that was framed: (1) positively as the percentage who remain free of influenza and have no vaccine side effects, or (2) negatively as the percentage who acquire influenza and have vaccine side effects. Questionnaires elicited expectations, decisions, and decisional conflict. Vaccines were telephoned 3 days later for a self-report of local and systemic side effects and work absenteeism. Both groups had similar immunization rates and decisional conflict scores. The positive frame group had lower and more realistic expectations of vaccine side effects, fewer systemic side effects, and less work absenteeism (p < 0.05). In contrast to previous studies of health care workers, framing did not influence patients' decisions, possibly due to the patients' awareness of their higher risk of influenza complications and greater desire to follow recommendations. The common practice of using negative frames when describing probabilities of side effects may need to be reexamined, considering its deleterious influence on self-reported side effects and work absenteeism.

Fundamental studies on a novel die concept for round-point shear-clinching

NASA Astrophysics Data System (ADS)

Hörhold, Réjane; Müller, Martin; Merklein, Marion; Meschut, Gerson

2016-10-01

A newly-developed round-point shear-clinching technology could increase the use of different materials like well formable aluminium and hardly formable ultra-high-strength steels (UHSS). This innovative technology joins in a single-stage process without any pilot-hole, surface pre-treatment or auxiliary joining part. The combination of an inner and outer punch realises an indirect cutting operation of the die-sided material, whereas the punch-sided material remains unharmed. The current die-sided tool set acts as a cutting die and enables a radial extrusion of the punch-sided material after being drawn though the created hole in the UHSS. The die has a fixed die depth. After ejecting the joined components, the slug has to be removed from the top of the spring-loaded anvil. The novel die concept investigated in this paper offers the possibility to push the slug continuously through the die in the joining direction. The removed slugs remain inside the die, so manual removal is unnecessary. The one-parted tool is supposed to be more robust than the multi-parted one that is currently used. This paper represents the task to evaluate the geometry of a useful shear-clinching die concept. To reduce the experimental effort, FEM should assist the development of the most promising approach. To quantify the success, conventional shear-clinching with opening die acts as a reference. The results show the high potential and the raison d'être of shear-clinching technologies as a mechanical joining technology for future multimaterial applications especially for UHSS.

Side Effects of Leukotriene Receptor Antagonists in Asthmatic Children.

PubMed

Erdem, Semiha Bahceci; Nacaroglu, Hikmet Tekin; Unsal Karkiner, Canan Sule; Gunay, Ilker; Can, Demet

2015-10-01

Leukotriene receptor antagonists (LTRAs) are drugs which have been widely used more than ten years. As the use of LTRAs increases, our knowledge with respect to their side effects increases as well. The objective of our study was to evaluat the observed side effects of LTRAs used in patients with astma. 1024 patients treated only with LTRAs owing to asthma or early wheezing were included in the study for a five-year period. The observed side effects of LTRAs in these patients were retrospectively investigated. The side effects were divided into two parts as psychiatric and non-psychiatric. Among the 1024 cases included in the study, 67.5% of the patients out of 41 with side effects were male, 32.5% were female and the average age was 6.5 years. The rate of patients with asthma was 63.41% and 36.58% of the patients had early wheezing. It was determined that sex, age and diagnosis (early wheezing or asthma) of the patients were ineffective in the emergence of side effects. The average period for the emergence of side effects was the first month. It was observed that hyperactivity was the most frequently observed psychiatric side effect and that abdominal pain was the non-psychiatric side effect. The side effects of LTRAs were common in children. Therefore, patients must be informed at the beginning of the treatment and they must be evaluated at certain intervals.

Gemini Surfactants Based on Bis-Imidazolium Alkoxy Derivatives as Effective Agents for Delivery of Nucleic Acids: A Structural and Spectroscopic Study.

PubMed

Pietralik, Zuzanna; Kołodziejska, Żaneta; Weiss, Marek; Kozak, Maciej

2015-01-01

The success rate of gene therapy depends on the efficient transfection of genetic material into cells. The golden mean between harmlessness and high effectiveness can be provided by synthetic lipid-like molecules that are similar to the components of biological membranes. Cationic gemini surfactants are one such moiety and because of their favourable physicochemical properties (double positive electric charge, reduced toxicity, low values of critical micelle concentration), they show great potential as delivery system components for genetic material in gene therapy. The aim of this study was to investigate the process of the complexation of cationic gemini surfactants with nucleic acids: double-stranded DNA of different sizes (21 bp, ~185 bp, ~20 kbp) and siRNA (21 bp). The tested series of dicationic surfactants consists of bis-imidazolium quaternary salts with varying lengths of hydrophobic side chains (m = 5, 6, 7, 8, 9, 11, 12, 14, 16). On the basis of the data obtained by circular dichroism spectroscopy and electrophoresis, we concluded that the studied gemini surfactants with long side chains effectively bind nucleic acids at low concentrations, which leads to the formation of stable lipoplexes. Images obtained by atomic force microscopy also confirmed the formation of vesicular structures, i.e., complexes between DNA and surfactants. The cytotoxicity of selected surfactants was also tested on HeLa cells. The surfactant toxicity significantly depends on surfactant geometry (the length of hydrophobic chain).

Gemini Surfactants Based on Bis-Imidazolium Alkoxy Derivatives as Effective Agents for Delivery of Nucleic Acids: A Structural and Spectroscopic Study

PubMed Central

Pietralik, Zuzanna; Kołodziejska, Żaneta; Weiss, Marek; Kozak, Maciej

2015-01-01

The success rate of gene therapy depends on the efficient transfection of genetic material into cells. The golden mean between harmlessness and high effectiveness can be provided by synthetic lipid-like molecules that are similar to the components of biological membranes. Cationic gemini surfactants are one such moiety and because of their favourable physicochemical properties (double positive electric charge, reduced toxicity, low values of critical micelle concentration), they show great potential as delivery system components for genetic material in gene therapy. The aim of this study was to investigate the process of the complexation of cationic gemini surfactants with nucleic acids: double-stranded DNA of different sizes (21 bp, ~185 bp, ~20 kbp) and siRNA (21 bp). The tested series of dicationic surfactants consists of bis-imidazolium quaternary salts with varying lengths of hydrophobic side chains (m = 5, 6, 7, 8, 9, 11, 12, 14, 16). On the basis of the data obtained by circular dichroism spectroscopy and electrophoresis, we concluded that the studied gemini surfactants with long side chains effectively bind nucleic acids at low concentrations, which leads to the formation of stable lipoplexes. Images obtained by atomic force microscopy also confirmed the formation of vesicular structures, i.e., complexes between DNA and surfactants. The cytotoxicity of selected surfactants was also tested on HeLa cells. The surfactant toxicity significantly depends on surfactant geometry (the length of hydrophobic chain). PMID:26641889

Microhardness, strength and strain field characterization of self-reacting friction stir and plug welds of dissimilar aluminum alloys

NASA Astrophysics Data System (ADS)

Horton, Karla Renee

Friction stir welding (FSW) is a solid state welding process with potential advantages for aerospace and automotive industries dealing with light alloys. Self-reacting friction stir welding (SR-FSW) is one variation of the FSW process being developed at the National Aeronautics and Space Administration (NASA) for use in the fabrication of propellant tanks. Friction plug welding is used to seal the exit hole that remains in a circumferential SR-FSW. This work reports on material properties and strain patterns developed in a SR-FSW with a friction plug weld. Specifically, this study examines the behavior of a SR-FSW formed between an AA2014-T6 plate on the advancing side and an AA2219-T87 plate on the retreating side and a SR-FSW (AA2014-T6 to AA2219-T87) with a 2219-T87 plug weld. This study presents the results of a characterization of the micro-hardness, joint strength, and strain field characterization of SR-FSW and FPW joints tested at room temperature and cryogenic temperatures. The initial weld microstructure analysis showed a nugget region with fine grains and a displaced weld seam from the advancing side past the thermo-mechanical affected zone (TMAZ) into the nugget region. The displaced material shared the same hardness as the parent material. Dynamic recrystallization was observed in the SR-FSW zone and the displaced weld seam region. The welds revealed a fine grain structure in the SR-FSW zone with a sharp demarcation seen on the advancing side and fairly diffuse flow observed on the retreating side. The parent material hardness is 145 HV700g with a drop in hardness starting at the HAZ to 130 HV700g. The hardness further drops in the TMAZ to118 HV700g with an increase representing a dispersed interface of AA2014-T6 material to 135 HV700g. The hardness then drops significantly within the nugget region to 85 HV700g followed by an increase through the retreating side TMAZ into the HAZ to 135 HV 700g. There was a sharp increase in the hardness value within the nugget region with the samples that were PWHT showing an increase of 58%. The welded joints were tested for ultimate strength. The testing variations included two specimen widths, two plug sizes (M3 and M5), room temperature and cryogenic testing, and post weld heat treated (PWHT) samples. Initial welds had an average ultimate strength of 370 MPa. There was a slight drop from initial weld strength to plug weld strength of approximately 13.8 MPa was observed with M3 plug strength approximately equal to M5 plug strength. The PWHT strengths at room temperature were slightly higher than non-PWHT of 13.8--20.7 MPa and PWHT strengths were equal to non-PWHT at cryogenic temperature. Non-PWHT had a cryogenic strength enhancement approximately 59.2 MPa and PWHT had a cryogenic strength enhancement of approximately 57.2 MPa in the M3 and M5 plugs. Within the subsets of data collected no major statistical significance in strength behavior was observed between the samples tested at room temperature or between the subsets tested at LN2. In almost all cases, failure occurred on the retreating side of the weld which corresponds to the softer material (AA2219-T87). Exceptions were characterized with flaws (weld defects) in the sample. In these cases, failure occurred on the advancing side, the side where flaws were detected. Ductile fracture was noted in most all samples. Digital image correlation using the ARAMIS system was used to define strain patterns in the weld joint. Strain accumulation was observed in the weld along the retreating side and around the plug. ARAMIS data in comparison to extensometer data shows a very reasonable comparison. The ARAMIS strain gage data showed the retreating side of the major diameter has a greater yield than the advancing side. This behavior is identical to the external electrical resistance strain gages.

Fabrication and characterization of epoxy/silica functionally graded composite material

NASA Astrophysics Data System (ADS)

Misra, N.; Kapusetti, G.; Pattanayak, D. K.; Kumar, A.

2011-09-01

Increased use of composites in aerospace and defense application induces the search for heat resistant material. In present study silica reinforced epoxy functionally graded material using quartz fabric is prepared with different thickness. The gradation in silica : epoxy matrix is maintained with one side pure epoxy to opposite side pure silica. Thermal and mechanical behaviour of the composites were studied. It was found that the temperature gradient of 350°C to 950°C could be maintained for 2 to 5 min if the thickness of insulating silica layer is increased from 0.5 mm to 16 mm. Mechanical properties such as flexural modulus and strength of FGM composites were also evaluated. Strength and modulus decreased with increase of insulating layer.

Mode trap for absorbing transverse modes of an accelerated electron beam

DOEpatents

Chojnacki, E.P.

1994-05-31

A mode trap to trap and absorb transverse modes formed by a beam in a linear accelerator includes a waveguide having a multiplicity of electrically conductive (preferably copper) irises and rings, each iris and ring including an aperture, and the irises and rings being stacked in a side-by-side, alternating fashion such that the apertures of the irises and rings are concentrically aligned. An absorbing material layer such as a dielectric is embedded in each iris and ring, and this absorbing material layer encircles, but is circumferentially spaced from its respective aperture. Each iris and ring includes a plurality of circumferentially spaced slots around its aperture and extending radially out toward its absorbing material layer. 9 figs.

49 CFR 176.800 - General stowage requirements.

Code of Federal Regulations, 2014 CFR

2014-10-01

... protection extending to the sides of the carboy box. This protective construction must be strong enough to permit stacking one on top of the other. (d) A Class 8 (corrosive material) material may not be stowed...

Iapetus: Unique Surface Properties and a Global Color Dichotomy from Cassini Imaging

NASA Astrophysics Data System (ADS)

Denk, Tilmann; Neukum, Gerhard; Roatsch, Thomas; Porco, Carolyn C.; Burns, Joseph A.; Galuba, Götz G.; Schmedemann, Nico; Helfenstein, Paul; Thomas, Peter C.; Wagner, Roland J.; West, Robert A.

2010-01-01

Since 2004, Saturn’s moon Iapetus has been observed repeatedly with the Imaging Science Subsystem of the Cassini spacecraft. The images show numerous impact craters down to the resolution limit of ~10 meters per pixel. Small, bright craters within the dark hemisphere indicate a dark blanket thickness on the order of meters or less. Dark, equator-facing and bright, poleward-facing crater walls suggest temperature-driven water-ice sublimation as the process responsible for local albedo patterns. Imaging data also reveal a global color dichotomy, wherein both dark and bright materials on the leading side have a substantially redder color than the respective trailing-side materials. This global pattern indicates an exogenic origin for the redder leading-side parts and suggests that the global color dichotomy initiated the thermal formation of the global albedo dichotomy.

Iapetus: unique surface properties and a global color dichotomy from Cassini imaging.

PubMed

Denk, Tilmann; Neukum, Gerhard; Roatsch, Thomas; Porco, Carolyn C; Burns, Joseph A; Galuba, Götz G; Schmedemann, Nico; Helfenstein, Paul; Thomas, Peter C; Wagner, Roland J; West, Robert A

2010-01-22

Since 2004, Saturn's moon Iapetus has been observed repeatedly with the Imaging Science Subsystem of the Cassini spacecraft. The images show numerous impact craters down to the resolution limit of approximately 10 meters per pixel. Small, bright craters within the dark hemisphere indicate a dark blanket thickness on the order of meters or less. Dark, equator-facing and bright, poleward-facing crater walls suggest temperature-driven water-ice sublimation as the process responsible for local albedo patterns. Imaging data also reveal a global color dichotomy, wherein both dark and bright materials on the leading side have a substantially redder color than the respective trailing-side materials. This global pattern indicates an exogenic origin for the redder leading-side parts and suggests that the global color dichotomy initiated the thermal formation of the global albedo dichotomy.

Application of C/C composites to the combustion chamber of rocket engines. Part 1: Heating tests of C/C composites with high temperature combustion gases

NASA Astrophysics Data System (ADS)

Tadano, Makoto; Sato, Masahiro; Kuroda, Yukio; Kusaka, Kazuo; Ueda, Shuichi; Suemitsu, Takeshi; Hasegawa, Satoshi; Kude, Yukinori

1995-04-01

Carbon fiber reinforced carbon composite (C/C composite) has various superior properties, such as high specific strength, specific modulus, and fracture strength at high temperatures of more than 1800 K. Therefore, C/C composite is expected to be useful for many structural applications, such as combustion chambers of rocket engines and nose-cones of space-planes, but C/C composite lacks oxidation resistivity in high temperature environments. To meet the lifespan requirement for thermal barrier coatings, a ceramic coating has been employed in the hot-gas side wall. However, the main drawback to the use of C/C composite is the tendency for delamination to occur between the coating layer on the hot-gas side and the base materials on the cooling side during repeated thermal heating loads. To improve the thermal properties of the thermal barrier coating, five different types of 30-mm diameter C/C composite specimens constructed with functionally gradient materials (FGM's) and a modified matrix coating layer were fabricated. In this test, these specimens were exposed to the combustion gases of the rocket engine using nitrogen tetroxide (NTO) / monomethyl hydrazine (MMH) to evaluate the properties of thermal and erosive resistance on the thermal barrier coating after the heating test. It was observed that modified matrix and coating with FGM's are effective in improving the thermal properties of C/C composite.

Prevention of post-partum hemorrhage by rectal Misoprostol: A randomized clinical trial

PubMed Central

Firouzbakht, Mozhgan; Kiapour, Azadeh; Omidvar, Shabnam

2013-01-01

Background: Post-partum hemorrhage (PPH) is a common cause of maternal mortality in developing countries. This trial was conducted to study the effectiveness and safety of rectal misoprostol for PPH. Aim: To assess the effectiveness and safety of misoprostol and comparing with oxytocin for prevention of PPH. Materials and Methods: Women were randomized to receive either two 200 μg rectal misoprostol tablets (study group) or 20 units oxytocin in 1000 cc normal saline intravenously (control group). The outcomes were incidence of PPH, amount of blood loss, duration of labor, incidence of side effects, pre- and post-delivery hemoglobin, and use of additional uterotonics. Finding: The incidence of PPH was 12% in the study group and 10% in the control group (P > 0.05). No significant difference was observed between the groups hematocrit (P > 0.05). Other variables including severe PPH and duration of the third stage of labor were similar in both groups. Conclusion: Rectal misoprostol was as effective as intravenous oxytocin for preventing post-partum hemorrhage with the same incidence of side effects and is recommended to be use as an uterotonic agent to manage third stage of labor routinely. PMID:23633849

A Comparison of Sexual Side Effects of Antidepressants With and Without Naltrexone.

PubMed

Thapa, Mona; Petrakis, Ismene; Ralevski, Elizabeth

2017-01-01

The aim of the study was to compare the rate of sexual side effects of the selective serotonin reuptake inhibitor paroxetine versus the tricyclic antidepressant desipramine and to examine the effect of co-prescription of naltrexone on sexual side effects among participants in a randomized clinical trial. This was a secondary analysis (N = 88) of veterans who participated in a 12-week trial. All veterans were randomized into one of four treatment groups: (a) desipramine/naltrexone, (b) desipramine/placebo, (c) paroxetine/naltrexone, and (d) paroxetine/placebo. The main outcome measure was the frequency of sexual side effects consisting of "decreased sex drive" and/or "impotence" reported by veterans at each weekly visit. Approximately 61% of the veterans reported sexual side effects at least once during the trial, and 26.4% reported sexual side effects throughout the study. There were no significant differences in the frequency of sexual side effects among the four treatment groups. The results were similar when the comparison was made between the two antidepressant groups. There were no significant differences in the reporting of sexual side effects between those receiving desipramine and paroxetine. Also, the comparison between naltrexone and placebo did not alter the results. This is the first study to compare frequency of sexual side effect reporting between paroxetine and desipramine. We found no statistically significant differences in sexual side effect reporting between the two antidepressants. Also, the addition of naltrexone did not show any beneficial effect on the sexual side effect profile.

How does the side-effect information in patient information leaflets influence peoples' side-effect expectations? A cross-sectional national survey of 18- to 65-year-olds in England.

PubMed

Webster, Rebecca K; Weinman, John; Rubin, G James

2017-12-01

To establish how the terms recommended by the European Commission to describe side-effect risk in patient information leaflets (PILs) influences expectations of side-effects and to identify factors associated with these side-effect expectations. A cross-sectional online survey was carried out by a market research company. Data were collected in England between 18th March and 1st April 2016. A total of 1003 adults aged between 18 and 65. Self-reported expectation that the described side-effects would affect participants if they took the medicine, measured on a likelihood scale from 1 (very unlikely) to 5 (very likely). Participants formed high expectations of side-effects for "very common" and "common" side-effects, with 51.9% and 45.0% of participants rating these as "very likely" or "likely" to happen to them, respectively. This fell to 8.1% for "uncommon," 5.8% for "rare" and 4.1% for "very rare." For each descriptor, higher expectations of side-effects were more associated with women or being from an ethnic minority, or having less education, a household illness, high perceived sensitivity to medicines or negative beliefs about medicines. The current use of verbal descriptors to communicate side-effect risk in PILs leads to high side-effect expectations. These expectations could contribute to nocebo-induced medication side-effects experienced by patients. Additional work is required to identify ways to improve the way risk information is conveyed in PILs. © 2017 The Authors Health Expectations Published by John Wiley & Sons Ltd.

Effect of trivalent iron substitution on structure and properties of PLZT ceramics

NASA Astrophysics Data System (ADS)

Dutta, S.; Choudhary, R. N. P.

2008-02-01

Polycrystalline samples of Fe-modified PLZT (lead lanthanum zirconate titanate) are prepared by a mixed-oxide reaction technique. The formation of the compound has been confirmed by X-ray powder diffraction studies. The unit cell structure of the material has been found to be rhombohedral. Fourier-transform infrared reflection (FTIR) spectra have been recorded to correspond the structural changes associated with the phase formation. The effects of Fe concentration on the microstructure and dielectric constant of PLZT materials have been investigated. The ferroelectric phase transition of PLFZT materials is studied using dielectric measurements, which shows a shift in the transition temperature towards the higher-temperature side with increased Fe ion concentration. The piezoelectric constants of this system are investigated by the same way of changed contents of Fe ion in the main PLZT compound. The optimum values of Qm, kp, and d33 are 73, 0.32 and 406. The electrical conductivity increases with the increase in Fe ion concentration.

A sophisticated simulation for the fracture behavior of concrete material using XFEM

NASA Astrophysics Data System (ADS)

Zhai, Changhai; Wang, Xiaomin; Kong, Jingchang; Li, Shuang; Xie, Lili

2017-10-01

The development of a powerful numerical model to simulate the fracture behavior of concrete material has long been one of the dominant research areas in earthquake engineering. A reliable model should be able to adequately represent the discontinuous characteristics of cracks and simulate various failure behaviors under complicated loading conditions. In this paper, a numerical formulation, which incorporates a sophisticated rigid-plastic interface constitutive model coupling cohesion softening, contact, friction and shear dilatation into the XFEM, is proposed to describe various crack behaviors of concrete material. An effective numerical integration scheme for accurately assembling the contribution to the weak form on both sides of the discontinuity is introduced. The effectiveness of the proposed method has been assessed by simulating several well-known experimental tests. It is concluded that the numerical method can successfully capture the crack paths and accurately predict the fracture behavior of concrete structures. The influence of mode-II parameters on the mixed-mode fracture behavior is further investigated to better determine these parameters.

Functionalized Poly(3,4-ethylenedioxy bithiophene) Films for Tuning Electrochromic and Thermoelectric Properties.

PubMed

Hu, Yongjing; Liu, Xiaofang; Jiang, Fengxing; Zhou, Weiqiang; Liu, Congcong; Duan, Xuemin; Xu, Jingkun

2017-10-05

Conductive thiophene-based polymers have garnered great attention for use in organic electron materials such as electrochromic and thermoelectric materials. However, they suffer from poor electron transport properties and long-term stability, leading to limited development eventually. Here, we proposed a strategy of functionalized thiophene-based polymers with oligo(ethylene glycol) or alkyl side chains and synthesized a series of poly(3,4-ethylenedioxy bithiophene)s (PEDTs) to tune their electrochromic and thermoelectric properties. An alkyl group bearing electronic ability at the thiophene ring effectively achieved a large increase in the electrical conductivity with nearly invariable Seebeck coefficient, resulting in an enhancement by 1 order of magnitude for the thermoelectric power factor. Moreover, the electrochromic properties of functionalized PEDTs gained an effective improvement in the optical contrast and coloration efficiency as well as stability with multicolor changes between neutral and oxidized states. The functionalized PEDTs can be proposed as an alternative strategy to tune the electrochromic and thermoelectric properties for organic polymer materials.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Salehi, M.; Jafari, S.A., E-mail: jafari@physics.sharif.edu; Center of Excellence for Complex Systems and Condensed Matter

Bismuth and its alloys provide a paradigm to realize three dimensional materials whose low-energy effective theory is given by Dirac equation in 3+1 dimensions. We study the quantum transport properties of three dimensional Dirac materials within the framework of Landauer–Büttiker formalism. Charge carriers in normal metal satisfying the Schrödinger equation, can be split into four-component with appropriate matching conditions at the boundary with the three dimensional Dirac material (3DDM). We calculate the conductance and the Fano factor of an interface separating 3DDM from a normal metal, as well as the conductance through a slab of 3DDM. Under certain circumstances themore » 3DDM appears transparent to electrons hitting the 3DDM. We find that electrons hitting the metal-3DDM interface from metallic side can enter 3DDM in a reversed spin state as soon as their angle of incidence deviates from the direction perpendicular to interface. However the presence of a second interface completely cancels this effect.« less

Method for maintaining a cutting blade centered in a kerf

DOEpatents

Blaedel, Kenneth L.; Davis, Pete J.; Landram, Charles S.

2002-01-01

A saw having a self-pumped hydrodynamic blade guide or bearing for retaining the saw blade in a centered position in the saw kerf (width of cut made by the saw). The hydrodynamic blade guide or bearing utilizes pockets or grooves incorporated into the sides of the blade. The saw kerf in the workpiece provides the guide or bearing stator surface. Both sides of the blade entrain cutting fluid as the blade enters the kerf in the workpiece, and the trapped fluid provides pressure between the blade and the workpiece as an inverse function of the gap between the blade surface and the workpiece surface. If the blade wanders from the center of the kerf, then one gap will increase and one gap will decrease and the consequent pressure difference between the two sides of the blade will cause the blade to re-center itself in the kerf. Saws using the hydrodynamic blade guide or bearing have particular application in slicing slabs from boules of single crystal materials, for example, as well as for cutting other difficult to saw materials such as ceramics, glass, and brittle composite materials.

Hydrodynamic blade guide

DOEpatents

Blaedel, Kenneth L.; Davis, Pete J.; Landram, Charles S.

2000-01-01

A saw having a self-pumped hydrodynamic blade guide or bearing for retaining the saw blade in a centered position in the saw kerf (width of cut made by the saw). The hydrodynamic blade guide or bearing utilizes pockets or grooves incorporated into the sides of the blade. The saw kerf in the workpiece provides the guide or bearing stator surface. Both sides of the blade entrain cutting fluid as the blade enters the kerf in the workpiece, and the trapped fluid provides pressure between the blade and the workpiece as an inverse function of the gap between the blade surface and the workpiece surface. If the blade wanders from the center of the kerf, then one gap will increase and one gap will decrease and the consequent pressure difference between the two sides of the blade will cause the blade to re-center itself in the kerf. Saws using the hydrodynamic blade guide or bearing have particular application in slicing slabs from boules of single crystal materials, for example, as well as for cutting other difficult to saw materials such as ceramics, glass, and brittle composite materials.

Thermoelectric Energy Harvesting Using Phase Change Materials (PCMs) in High Temperature Environments in Aircraft

NASA Astrophysics Data System (ADS)

Elefsiniotis, A.; Becker, Th.; Schmid, U.

2014-06-01

Wireless, energy-autonomous structural health-monitoring systems in aircraft have the potential of reducing total maintenance costs. Thermoelectric energy harvesting, which seems the best choice for creating truly autonomous health monitoring sensors, is the principle behind converting waste heat to useful electrical energy through the use of thermoelectric generators. To enhance the temperature difference across the two sides of a thermoelectric generator, i.e. increasing heat flux and energy production, a phase change material acting as thermal mass is attached on one side of the thermoelectric generators while the other side is placed on the aircraft structure. The application area under investigation for this paper is the pylon aft fairing, located near the engine of an aircraft, with temperatures reaching on the inside up to 350 °C. Given these harsh operational conditions, the performance of a device, containing erythritol as a phase change material, is evaluated. The harvested energy reaching values up to 81.4 J can be regulated by a power management module capable of storing the excess energy and recovering it from the medium powering a sensor node and a wireless transceiver.

Microvessel Density Evaluation of the Effect of Enamel Matrix Derivative on Soft Tissue After Implant Placement: A Preliminary Study.

PubMed

Guimarães, George Furtado; de Araújo, Vera Cavalcanti; Nery, James Carlos; Peruzzo, Daiane Cristina; Soares, Andresa Borges

2015-01-01

Enamel matrix derivative (EMD) is commonly used in periodontal therapy and has been used successfully for periodontal regeneration. In addition, this material has a possible angiogenic effect that has been associated with enhanced wound healing. The aim of this study was to evaluate the effect of EMD on microvessel density (angiogenesis) on the soft tissues surrounding newly placed implants after 14 days. Five patients were selected, each requiring at least one implant on each side of the maxilla, in a split-mouth experimental design. The implants were placed in a two-stage procedure. Each side was then randomized as test or control. On the test side, 0.1 mL of EMD was topically applied to the soft tissues surrounding the implants, while the control side did not receive any treatment. Second-stage surgery was performed after 14 days. A 6-mm punch biopsy was performed for each implant, with the samples subsequently prepared for histology and immunohistochemistry. Quantitative vascularization analysis was performed, which involved counting three areas or "hotspots" containing vessels strongly positive for CD34 and CD105, a pan-endothelial and new vessel marker, respectively. There was no significant difference between test and control groups when evaluating the formation of new blood vessels. The total number of blood vessels, however, was significantly higher in the group treated with EMD (test group). Within the limits of the present study, it can be concluded that topical application of EMD on the soft tissues surrounding newly placed implants resulted in an increased number of blood vessels at 14 days, suggesting that EMD may play a beneficial role in this aspect of wound healing.

Side Effects to Antidepressant Treatment in Patients With Depression and Comorbid Panic Disorder.

PubMed

Shankman, Stewart A; Gorka, Stephanie M; Katz, Andrea C; Klein, Daniel N; Markowitz, John C; Arnow, Bruce A; Manber, Rachel; Rothbaum, Barbara O; Thase, Michael E; Schatzberg, Alan F; Keller, Martin B; Trivedi, Madhukar H; Kocsis, James H

2017-04-01

Side effects to antidepressant medication can affect the efficacy of treatment, but few predictors foretell who experiences side effects and which side effects they experience. This secondary data analysis examined whether depressed patients with comorbid panic disorder were more likely to experience side effects than those without panic disorder. The study also examined whether greater burden of side effects predicted a poorer treatment course for patients with panic disorder than those without panic disorder. To examine the specificity of these effects, analyses also examined 2 other anxiety disorders-social phobia and generalized anxiety disorder (GAD). Between 2002 and 2006, a large sample (N = 808) of chronically depressed individuals (assessed using the Structured Clinical Interview for DSM-IV-TR Axis I Disorders [SCID-IV]) received antidepressants according to a predetermined algorithm for 12 weeks. Every 2 weeks, depressive symptoms (per the Hamilton Depression Rating Scale) and side effects (specific side effects as well as several indicators of side effect burden) were assessed. Lifetime diagnosis of panic disorder (assessed using the SCID-IV) at baseline was associated with higher likelihood of gastrointestinal (OR = 1.6 [95% CI, 1.0-2.6]), cardiac (OR = 1.8 [95% CI, 1.1-3.1]), neurologic (OR = 2.6 [95% CI, 1.6-4.2]), and genitourinary side effects (OR = 3.0 [95% CI, 1.7-5.3]) during treatment. Increases in side effect frequency, intensity, and impairment over time were more strongly associated with increases in depressive symptoms for patients with panic disorder compared to those without panic disorder. Neither social phobia nor GAD was associated with these effects. Potentially due to heighte​ned interoceptive awareness of changes in their body, chronically depressed individuals with panic disorder may be at greater risk than those without panic disorder for antidepressant side effects and to experience a worsening of depressive symptoms as a result of these side effects over time. ClinicalTrials.gov identifier: NCT00057551​. © Copyright 2017 Physicians Postgraduate Press, Inc.

Deuteration as a Means to Tune Crystallinity of Conducting Polymers

DOE PAGES

Jakowski, Jacek; Huang, Jingsong; Garashchuk, Sophya; ...

2017-08-25

The effects of deuterium isotope substitution on conjugated polymer chain stacking of poly(3-hexylthiophene) is studied in this paper experimentally by X-ray diffraction (XRD) in combination with gel permeation chromatography and theoretically using density functional theory and quantum molecular dynamics. For four P3HT materials with different levels of deuteration (pristine, main-chain deuterated, side-chain deuterated, and fully deuterated), the XRD measurements show that main-chain thiophene deuteration significantly reduces crystallinity, regardless of the side-chain deuteration. The reduction of crystallinity due to the main-chain deuteration is a quantum nuclear effect resulting from a static zero-point vibrational energy combined with a dynamic correlation of themore » dipole fluctuations. The quantum molecular dynamics simulations confirm the interchain correlation of the proton–proton and deuteron–deuteron motions but not of the proton–deuteron motion. Thus and finally, isotopic purity is an important factor affecting stability and properties of conjugated polymer crystals, which should be considered in the design of electronic and spintronic devices.« less

Deuteration as a Means to Tune Crystallinity of Conducting Polymers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jakowski, Jacek; Huang, Jingsong; Garashchuk, Sophya

The effects of deuterium isotope substitution on conjugated polymer chain stacking of poly(3-hexylthiophene) is studied in this paper experimentally by X-ray diffraction (XRD) in combination with gel permeation chromatography and theoretically using density functional theory and quantum molecular dynamics. For four P3HT materials with different levels of deuteration (pristine, main-chain deuterated, side-chain deuterated, and fully deuterated), the XRD measurements show that main-chain thiophene deuteration significantly reduces crystallinity, regardless of the side-chain deuteration. The reduction of crystallinity due to the main-chain deuteration is a quantum nuclear effect resulting from a static zero-point vibrational energy combined with a dynamic correlation of themore » dipole fluctuations. The quantum molecular dynamics simulations confirm the interchain correlation of the proton–proton and deuteron–deuteron motions but not of the proton–deuteron motion. Thus and finally, isotopic purity is an important factor affecting stability and properties of conjugated polymer crystals, which should be considered in the design of electronic and spintronic devices.« less

Health-Related Quality of Life, Depression, Anxiety, and Self-Image in Acute Lymphocytic Leukemia Survivors

PubMed Central

Baytan, Birol; Aşut, Çiğdem; Çırpan Kantarcıoğlu, Arzu; Sezgin Evim, Melike; Güneş, Adalet Meral

2016-01-01

Objective: With increasing survival rates in childhood acute lymphocytic leukemia (ALL), the long-term side effects of treatment have become important. Our aim was to investigate health-related quality of life, depression, anxiety, and self-image among ALL survivors. Materials and Methods: Fifty patients diagnosed with ALL and their siblings were enrolled. The Kovacs Children’s Depression Inventory, State-Trait Anxiety Inventory, Offer Self-Image Questionnaire, and Pediatric Quality of Life InventoryTM were used for collecting data. ANOVA tests were used to determine if there were any significant differences between groups. Results: ALL survivors had higher depression, more anxiety symptoms, lower quality of life, and more negative self-image when compared to their siblings. Conclusion: Continuous diagnostic and interventional mental health services might be necessary for possible emotional side effects of treatment during and after the treatment. Rehabilitation and follow-up programs should be implemented for children during and after treatment for ALL. PMID:27094799

An investigation of enhanced capability thermal barrier coating systems for diesel engine components

NASA Technical Reports Server (NTRS)

Holtzman, R. L.; Layne, J. L.; Schechter, B.

1984-01-01

Material systems and processes for the development of effective and durable thermal barriers for heavy duty diesel engines were investigated. Seven coating systems were evaluated for thermal conductivity, erosion resistance, corrosion/oxidation resistance, and thermal shock resistance. An advanced coating system based on plasma sprayed particle yttria stabilized zirconia (PS/HYSZ) was judged superior in these tests. The measured thermal conductivity of the selected coating was 0.893 W/m C at 371 C. The PS/HYSZ coating system was applied to the piston crown, fire deck and valves of a single cylinder low heat rejection diesel engine. The coated engine components were tested for 24 hr at power levels from 0.83 MPa to 1.17 MPa brake mean effective pressure. The component coatings survived the engine tests with a minimum of distress. The measured fire deck temperatures decreased 86 C (155 F) on the intake side and 42 C (75 F) on the exhaust side with the coating applied.

Building America Case Study: Trade-Friendly Retrofit Insulated Panels for Existing Buildings, Albany, New York

DOE Office of Scientific and Technical Information (OSTI.GOV)

This project evaluated the effectiveness and affordability of integrating retrofit insulated panels into a re-siding project. The Partnership for Home Innovation (PHI) teamed with New York State Energy Research and Development Authority (NYSERDA), the Albany Housing Authority (AHA), and the New York State Weatherization Assistance Program (WAP) administered by Albany Community Action Partnership to demonstrate an energy retrofit and siding upgrade on a two-story, seven unit, multifamily building in Albany New York (CZ 5). The project focused on accomplishing three goals - doubling the existing wall thermal resistance (from approximately R-13 to a weighted average of R-27), reduction of buildingmore » air leakage, and completion of the retrofit within a budget where the additional cost for upgrading wall's thermal resistance is equal to the cost of the standard re-siding effort (i.e., the total cost of the energy efficient re-siding scope of work is not more than double the cost of the standard re-siding effort). Lessons learned from the project strongly indicate that the retrofit panel technology can be installed using common installation practices and with minimal training. Other lessons learned include limitation on the use of standard air sealing materials during cold weather installations and the need to develop better installation guidance for trades working with the level of tolerances that may be present in the existing structure. This technology demonstration showed that exterior retrofit panels provide a viable and reasonable option for the siding trades to increase market opportunities and achieve synergistic benefits for aesthetic upgrades to a building's exterior.« less

Comparison of Olfactory Function before and After Endoscopic Sinus Surgery

PubMed Central

Seyed Toutounchi, Seyed Javad; Yazdchi, Mohamad; Asgari, Rana; Seyed Toutounchi, Negisa

2018-01-01

Introduction: Olfactory loss in patients with chronic rhinosinusitis has been measured by different methods. However, the results have been variable, and it is not clear whether endoscopic sinus surgery significantly improves olfactory function. This study was performed to evaluate the influence of endoscopic sinus surgery on olfactory function in patients with chronic rhinosinusitis. Materials and Methods: In this prospective analytic study, 73 patients (mean age, 39.63±12.94 years) with a diagnosis of polyps and sinusitis during 2011 were studied. The olfaction test was performed with three solutions; one with no odor (water) and two with phenylethyl alcohol (50% and 90% dilution, respectively). The patients’ olfaction state were graded as no olfaction, or low, moderate or good olfaction before and 1 and 3 months after surgery, and was given scores between 0 and 3 and evaluated quantitatively. Results: Right-side olfaction was improved in 68.5% and left side in 67.1% of patients. Mean olfaction score on the right and left side was significantly improved after surgery in comparison with basic scores (before and after on the right side: 0.95±0.88 and 2.02±1.04; before and after on the left side: 1.02±0.84 and 2.00±1.21; both P<0.001). Improvement after surgery in cases with left- and right-side anosmia was 66.7% and 61.9%, in low olfaction was 82.3% and 72.7% and in moderate olfaction was 66.7% and 80%. Conclusion: In patients with rhinosinusitis, endoscopic sinus surgery has considerable effect in improving olfactory function. PMID:29387662

Medications and Side Effects

MedlinePlus

... to fully work. You might feel some side effects of your medication before your feel the benefits – ... as sleepiness, anxiety or headache) is a side effect or a symptom of your illness. Many side ...

Biodegradable Drug-Loaded Hydroxyapatite Nanotherapeutic Agent for Targeted Drug Release in Tumors.

PubMed

Sun, Wen; Fan, Jiangli; Wang, Suzhen; Kang, Yao; Du, Jianjun; Peng, Xiaojun

2018-03-07

Tumor-targeted drug delivery systems have been increasingly used to improve the therapeutic efficiency of anticancer drugs and reduce their toxic side effects in vivo. Focused on this point, doxorubicin (DOX)-loaded hydroxyapatite (HAP) nanorods consisting of folic acid (FA) modification (DOX@HAP-FA) were developed for efficient antitumor treatment. The DOX-loaded nanorods were synthesized through in situ coprecipitation and hydrothermal method with a DOX template, demonstrating a new procedure for drug loading in HAP materials. DOX could be efficiently released from DOX@HAP-FA within 24 h in weakly acidic buffer solution (pH = 6.0) because of the degradation of HAP nanorods. With endocytosis under the mediation of folate receptors, the nanorods exhibited enhanced cellular uptake and further degraded, and consequently, the proliferation of targeted cells was inhibited. More importantly, in a tumor-bearing mouse model, DOX@HAP-FA treatment demonstrated excellent tumor growth inhibition. In addition, no apparent side effects were observed during the treatment. These results suggested that DOX@HAP-FA may be a promising nanotherapeutic agent for effective cancer treatment in vivo.

Coping strategies used by hospitalized children with cancer undergoing chemotherapy.

PubMed

Sposito, Amanda Mota Pacciulio; Silva-Rodrigues, Fernanda Machado; Sparapani, Valéria de Cássia; Pfeifer, Luzia Iara; de Lima, Regina Aparecida Garcia; Nascimento, Lucila Castanheira

2015-03-01

To analyze coping strategies used by children with cancer undergoing chemotherapy during hospitalization. This was an exploratory study to analyze qualitative data using an inductive thematic analysis. Semistructured interviews using puppets were conducted with 10 children with cancer, between 7 and 12 years old, who were hospitalized and undergoing chemotherapy. The coping strategies to deal with chemotherapy were: understanding the need for chemotherapy; finding relief for the chemotherapy's side effects and pain; seeking pleasure in nourishment; engaging in entertaining activities and having fun; keeping the hope of cure alive; and finding support in religion. Children with cancer undergoing chemotherapy need to cope with hospitalizations, pain, medication side effects, idle time, and uncertainty regarding the success of treatment. These challenges motivated children to develop their own coping strategies, which were effective while undergoing chemotherapy. By gaining knowledge and further understanding about valid coping strategies during chemotherapy treatment, health professionals can mobilize personal and material resources from the children, health teams, and institutions aiming to potentiate the use of these strategies to make treatments the least traumatic. © 2015 Sigma Theta Tau International.

Picibanil (OK-432) in the treatment of head and neck lymphangiomas in children

PubMed Central

Rebuffini, Elena; Zuccarino, Luca; Grecchi, Emma; Carinci, Francesco; Merulla, Vittorio Emanuele

2012-01-01

Background: Picibanil (OK-432) is a lyophilized mixture of group A Streptococcus pyogenes with antineoplastic activity. Because of its capacity to produce a selective fibrosis of lymphangiomas (LMs), it has been approved by Japanese administration in 1995 for the treatment of LMs. Materials and Methods: We treated 15 children (age range: 6-60 months) affected by head and neck macrocystic LMs with intracystic injections (single dose of 0.2 mL) of Picibanil (1-3 injections). Results: Complete disappearance of the lesion was noticed in eight (53.33%) cases, a marked (>50%) reduction of LMs was found five (33.33%) cases, while a moderate (<50%) response was recorded in two (13.33%) cases. Picibanil side effects included fever, local inflammation, and transitory increase of blood platelets’ concentration; a single case of anemia was resolved with concentrated red blood cells transfusion. Conclusions: Intracystic injection of Picibanil is an effective and safe treatment for macrocystic LMs in pediatric patients and may represent the treatment of choice in such cases, especially where surgical excision is associated with the risk of functional/cosmetic side effects. PMID:23814582

The efficacy of Iranian herbal medicines in alleviating hot flashes: A systematic review

PubMed Central

Ghazanfarpour, Masumeh; Sadeghi, Ramin; Abdolahian, Somayeh; Latifnejad Roudsari, Robab

2016-01-01

Background: Hot flashes are the most common symptoms experienced by women around the time of menopause. Many women are interested in herbal medicines because of fear of side effects of hormone therapy. Objective: The aim of this systematic review was to assess the effectiveness of Iranian herbal medicines in alleviating hot flashes. Materials and Methods: MEDLINE (1966 to January 2015), Scopus (1996 to January 2015), and Cochrane Central Register of Controlled Trials (The Cochrane Library, issue 1, 2015) were searched along with, SID, Iran Medex, Magiran, Medlib and Irandoc. Nineteen randomized controlled trials met the inclusion criteria. Results: Overall, studies showed that Anise (Pimpinella anisum), licorice (Glycyrrhizaglabra), Soy, Black cohosh, Red clover, Evening primrose, Flaxseed, Salvia officinalis, Passiflora، itex Agnus Castus, Piascledine (Avacado plus soybean oil), St. John's wort (Hypericum perforatum), and valerian can alleviate the side effects of hot flashes. Conclusion: This research demonstrated the efficacy of herbal medicines in alleviating hot flashes, which are embraced both with people and health providers of Iran Therefore, herbal medicine can be seen as an alternative treatment for women experiencing hot flashes. PMID:27294213

Cancer Treatment for Women: Possible Sexual Side Effects

MedlinePlus

... the clitoris. These play a major part in sexual arousal in women. Removing the vulva and the clitoris ... www.cancer.org/treatment/treatments-and-side-effects/physical-side-effects/fertility-and-sexual-side-effects/sexuality-for-women-with-cancer.html. ...

"There is a chain of connections": using syndemics theory to understand HIV treatment side effects.

PubMed

Gagnon, Marilou

2018-03-12

Side effects are central to the experience of living longer with HIV but rarely have they been studied alone. Unlike other aspects of that experience, like quality of life, treatment adherence, chronicity, episodic disability, aging, health, and viral load suppression, side effects have not benefited from the same level of empirical and theoretical engagement from qualitative researchers. In this paper, we draw on syndemics theory and 50 qualitative interviews to better understand the experience of HIV treatment side effects. Two main categories were identified in the data: side effects as a product and side effects as a risk factor. The first category suggests that side effects are not just the product of taking antiretroviral drugs. They are also the product of particular conditions and tend to cluster with other health problems. The second category puts forward the idea that side effects can act as a syndemic risk factor by exposing PLWH to a greater risk of developing health problems and creating conditions in which psychosocial issues are more likely to emerge. The paper concludes by calling for more research on the complex nature of side effects and for the development of comprehensive approaches for the assessment and management of side effects.

Patient-provider communication and hormonal therapy side effects in breast cancer survivors.

PubMed

Lin, Jenny J; Chao, Jennifer; Bickell, Nina A; Wisnivesky, Juan P

2017-09-01

Side effects from hormonal therapy (HT) for breast cancer treatment occur frequently and are associated with worse quality of life and HT non-adherence. Whether improved patient-physician communication is associated with patients' reporting of side effects is unknown. We undertook this study to assess factors associated with women's reports of HT side effects. Between December 2012 and April 2013, we conducted a cross-sectional survey of breast cancer patients undergoing HT in an urban medical center. Descriptive statistics, univariate analyses, and multivariate analyses were used to evaluate associations. Of the 100 participants, 67% reported having HT side effects. However, when prompted, an additional 9% reported experiencing specific HT-related symptoms. Despite very high communication scores, one-third of participants reported they had not discussed side effects with providers. Multivariate analysis showed that after controlling for age, education, race, and medication beliefs, women who had difficulty asking providers for more information were more likely to report side effects (odds ratio 8.27, 95% confidence interval 1.01-69.88). Although HT side effects often occur and are bothersome, patient-provider discussions about side effects remain suboptimal. Providers should actively ask patients about medication side effects so that they can be addressed to improve quality of life and potentially, medication adherence.

Method for Forming Fiber Reinforced Composite Bodies with Graded Composition and Stress Zones

NASA Technical Reports Server (NTRS)

Singh, Mrityunjay (Inventor); Levine, Stanley R. (Inventor); Smialek, James A. (Inventor)

1999-01-01

A near-net, complex shaped ceramic fiber reinforced silicon carbide based composite bodies with graded compositions and stress zones is disclosed. To provide the composite a fiber preform is first fabricated and an interphase is applied by chemical vapor infiltration, sol-gel or polymer processes. This first body is further infiltrated with a polymer mixture containing carbon, and/or silicon carbide, and additional oxide, carbide, or nitride phases forming a second body. One side of the second body is spray coated or infiltrated with slurries containing high thermal expansion and oxidation resistant. crack sealant phases and the other side of this second body is coated with low expansion phase materials to form a third body. This third body consisting of porous carbonaceous matrix surrounding the previously applied interphase materials, is then infiltrated with molten silicon or molten silicon-refractory metal alloys to form a fourth body. The resulting fourth body comprises dense composites consisting of fibers with the desired interphase which are surrounded by silicon carbide and other second phases materials at the outer and inner surfaces comprising material of silicon, germanium, refractory metal suicides, borides, carbides, oxides, and combinations thereof The resulting composite fourth body has different compositional patterns from one side to the other.

Dual chamber system providing simultaneous etch and deposition on opposing substrate sides for growing low defect density epitaxial layers

DOEpatents

Kulkarni, Nagraj S [Knoxville, TN; Kasica, Richard J. ,

2011-03-08

A dual-chamber reactor can include a housing enclosing a volume having a divider therein, where the divider defines a first chamber and a second chamber. The divider can include a substrate holder that supports at least one substrate and exposes a first side of the substrate to the first chamber and a second side of the substrate to the second chamber. The first chamber can include an inlet for delivering at least one reagent to the first chamber for forming a film on the first side of the substrate, and the second chamber can include a removal device for removing material from the second side of the substrate.

Protective effects of persian honey, Apis Mellifera Meda Skorikov on side effects of chemotherapy and ischemia/reperfusion induced testicular injury.

PubMed

Gholami, Mohammadreza; Abbaszadeh, Abolfazl; Baharvand, Parastoo; Hasanvand, Afshin; Hasanvand, Amin; Gharravi, Anneh Mohammad

2018-05-23

Introduction The aim of the present study was to survey the protective effect of pretreatment with Persian honey on amelioration of side effects of chemotherapy and ischemia/reperfusion induced testicular injury. Materials and methods Forty adult's male wistar rats were divided into four groups of ischemia-reperfusion (IR), honey + ischemia-reperfusion (HIR), Busulfan (B) and Busulfan intraperitoneally+ honey (BH). The seminiferous tubules were rated for their modified spermatogenesis index (SI) by Johnsons score. Detection of single- and double-stranded DNA breaks at the early stages of apoptosis was performed using the in-situ cell death detection kit. Total serum concentration of Follicle-stimulating hormone (FSH) , Luteinizing hormone (LH) and testosterone was measured using ELISA. All data were expressed as mean ± SD and significance was set at p≤0.05. Results Honey improved SI in the HIR and BH groups and serum levels of FSH and LH in the BH and HIR groups (p<0.001). Also, serum levels of testosterone were significantly higher in BH and HIR groups. But, apoptotic cells in IR and B groups significantly increased (p<0.001), while in HIR and BH groups, the number of apoptotic cells decreased and the positive cells of TUNEL (TdT-mediated dUTP-X nick end labelling) staining were detected in spermatocytes and spermatid. Discussion Pretreatment with honey protect testis against chemotherapy and testicular IR injury, increase FSH and LH and testosterone and decrease the cellular damage and apoptosis. Honey can decrease the side effects of chemotherapy on reproductive system and prevent sterility.

49 CFR 587.5 - Incorporated materials.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Transportation Other Regulations Relating to Transportation (Continued) NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) DEFORMABLE BARRIERS Side Impact Moving Deformable Barrier § 587.5 Incorporated materials. (a) The drawings and specifications referred to in this regulation...

49 CFR 587.5 - Incorporated materials.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 49 Transportation 7 2012-10-01 2012-10-01 false Incorporated materials. 587.5 Section 587.5 Transportation Other Regulations Relating to Transportation (Continued) NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) DEFORMABLE BARRIERS Side Impact Moving Deformable...

49 CFR 587.5 - Incorporated materials.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 49 Transportation 7 2014-10-01 2014-10-01 false Incorporated materials. 587.5 Section 587.5 Transportation Other Regulations Relating to Transportation (Continued) NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) DEFORMABLE BARRIERS Side Impact Moving Deformable...

49 CFR 587.5 - Incorporated materials.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 49 Transportation 7 2013-10-01 2013-10-01 false Incorporated materials. 587.5 Section 587.5 Transportation Other Regulations Relating to Transportation (Continued) NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) DEFORMABLE BARRIERS Side Impact Moving Deformable...

Preventing pressure sores of the nasal ala after nasotracheal tube intubation: from animal model to clinical application.

PubMed

Huang, Tze-Ta; Tseng, Chih-En; Lee, Tsan-Mu; Yeh, Jen-Ying; Lai, Yu-Yung

2009-03-01

Nasal-ala pressure sores induced by nasotracheal intubation are common complications of oral and maxillofacial surgery, but are easily ignored. To determine whether such sores could be prevented, we studied the effects of a combination of cushioning material in an animal model, and then analyzed the efficacy of this combination clinically. Four pigs received nasotracheal intubation. Each pig received intubation for 4, 8, 12, or 16 hours. Outcomes from pigs undergoing 500-gram-weight compression on each nostril were compared: one nostril received an application of cushioning materials, and the contralateral nostril did not. After the required study period, clinical assessment and further evaluation were performed by measuring pressure-sore dimensions and performing incisional biopsies. Clinical applications of this protective technique were then undertaken. Eight patients who underwent intubation without Soft Liner (GC Co, Tokyo, Japan) and DuoDERM CGF (ConvaTec, Inc, Princeton, NJ) protection, and 10 patients with Soft Liner and DuoDERM protection, were evaluated. The protective efficacy of the cushioning materials was significant in the animal model as well as in clinical practice. Pressure sores were avoided on the protected side, with severe tissue necrosis documented on the control side. We found that the combined use of Soft Liner and DuoDERM reduced the size and severity of nasal-ala pressure sores attributable to nasotracheal intubation during oral and maxillofacial surgery.

Side effect burden of antipsychotic drugs in real life - Impact of gender and polypharmacy.

PubMed

Iversen, Trude Seselie Jahr; Steen, Nils Eiel; Dieset, Ingrid; Hope, Sigrun; Mørch, Ragni; Gardsjord, Erlend Strand; Jørgensen, Kjetil Nordbø; Melle, Ingrid; Andreassen, Ole A; Molden, Espen; Jönsson, Erik G

2018-03-02

Antipsychotic-associated side effects are well known and represent a significant treatment challenge. Still, few large studies have investigated the overall side effect burden of antipsychotics in real-life settings. To describe the occurrence of side effects and perceived burden of antipsychotics in a large naturalistic sample, taking polypharmacy and patient characteristics into account. Patients (n=1087) with psychotic disorders were assessed for side effects using the Udvalg for Kliniske Undersøgelser (UKU) side effect rating scale in addition to assessment of clinical and pharmacological data. Statistical analyses were performed controlling for possible confounding factors. Use of antipsychotics showed significant associations to neurologic and sexual symptoms, sedation and weight gain, and >75% of antipsychotics-users reported side effects. More side effects were observed in patients using several antipsychotics (p=0.002), with increasing total dose (p=0.021) and with antipsychotics in combinations with other psychotropic drugs. Patients and investigators evaluated the side effect burden differently, particularly related to severity, gender and antipsychotics dose. Twice as many females described side effect burden as severe (p=0.004). Patients with psychotic disorders have a high occurrence of symptoms associated with use of antipsychotics, and polypharmacy and female gender are seemingly risk factors for reporting a severe side effect burden. Due to the cross-sectional design evaluation of causality is tentative, and these findings should be further investigated in prospective studies. Copyright © 2017 Elsevier Inc. All rights reserved.

The Glasgow antipsychotic side-effects scale for clozapine in inpatients and outpatients with schizophrenia or schizoaffective disorder.

PubMed

Ignjatović Ristić, Dragana; Cohen, Dan; Obradović, Andrea; Nikić-Đuričić, Katarina; Drašković, Marija; Hinić, Darko

2018-02-01

The inconsistency in clinician and patient ratings of clozapine-induced side effects underscore the need to supplement clinician-based estimates of side effects with patient-reported ones. The main aims of the study are validation of the Glasgow antipsychotic side-effects scale for clozapine (GASS-C) in Serbian inpatients/outpatients with schizophrenia or schizo-affective disorder and recommendations for its future use, based on common and rare clozapine-associated side-effects. The GASS-C was administered to 95 outpatients/inpatients diagnosed with schizophrenia, schizoaffective, or chronic psychotic disorder. The scale showed good overall reliability, with an internal consistency coefficient of α = 0.84, an average retest coefficient of rho = 0.76, and a Spearman-Brown coefficient of validity of 0.81. Side effects were absent or mild in 64.2% of the patients, moderate in 31.6%, severe in 4.2%; 14% of the subjects considered their symptoms distressing. The most commonly reported side-effects were drowsiness, thirst, frequent urination, and dry mouth. Women reported more side effects than men, and patients not in a relationship reported significantly fewer side effects than patients in a relationship. Results indicate a weak positive correlation (rho = 0.231; p = .025) between severity of side effects and clozapine dose. The GASS-C showed good psychometric characteristics in clinical population of patients on clozapine. In future studies, clozapine serum concentrations should be measured when using the GASS-C to monitor side effects.

Learning to experience side effects after antidepressant intake - Results from a randomized, controlled, double-blind study.

PubMed

Rheker, Julia; Winkler, Alexander; Doering, Bettina K; Rief, Winfried

2017-02-01

Side effects play a key role in patients' failure to take antidepressants. There is evidence that verbal suggestions and informed consent elicit expectations that can in turn trigger the occurrence of side effects. Prior experience or learning mechanisms are also assumed to contribute to the development of side effects, although their role has not been thoroughly investigated. In this study, we examined whether an antidepressant's side effects can be learned via Pavlovian conditioning. Participants (n = 39) were randomly allocated to one of two groups and were exposed to a classical conditioning procedure. During acquisition, 19 participants received amitriptyline and 20 participants received a placebo pill. Pills were taken for four nights together with a novel-tasting drink. After a washout phase, both groups received a placebo pill together with the novel-tasting drink (evocation). Side effects were assessed via the Generic Assessment of Side Effects Scale prior to acquisition (baseline), after acquisition, and after evocation. A score of antidepressant-specific side effects was calculated. Participants taking amitriptyline reported significantly more antidepressant-specific side effects after acquisition compared to both baseline and the placebo group. After evocation, participants who underwent the conditioning procedure with amitriptyline reported significantly more antidepressant-specific side effects than those who never received amitriptyline, even though both groups received a placebo. Our results indicate that antidepressant side effects can be learned using a conditioning paradigm and evoked via a placebo pill when applied with the same contextual factors as the verum.

The association of HIV/AIDS treatment side effects with health status, work productivity, and resource use.

PubMed

daCosta DiBonaventura, Marco; Gupta, Shaloo; Cho, Michelle; Mrus, Joseph

2012-01-01

Due to stable incidence and improved survival rates, there are an increasing number of patients living with HIV/AIDS in the USA. Although highly effective, current antiretroviral therapies are associated with a variety of side effects. The role side effects play on health outcomes has not been fully examined. The current study assessed the association of medication side effects with (1) self-assessed health status; (2) work productivity and activity impairment; and (3) healthcare resource utilization. Data were from a cross-sectional patient-reported survey fielded in the USA using a dual methodology of Internet and paper questionnaires. A total of 953 patients living with HIV/AIDS who were currently taking a medication for their condition were included in the analyses. The most frequent side effects reported by patients were fatigue (70.72%), diarrhea (62.96%), insomnia (58.97%), dizziness (52.78%), neuropathy (52.68%), joint pain (52.36%), nausea (51.63%), and abdominal pain (50.37%). The presence of each side effect was associated with reduced self-assessed health status, increased productivity loss, increased activity impairment, and increased healthcare resource use. Controlling for CD4 cell counts in regression modeling did little to diminish the impact of side effects. Although not all side effects were associated with all outcomes, every side effect was associated with worse health status, some measure of increased work productivity loss, and/or some measure of increased healthcare resource use. Patients are living longer with HIV and, therefore, spending a greater length of time on treatment. The results of the current study suggest that many of these patients are experiencing a wide array of side effects from these therapies. These side effects have demonstrated a profound association with self-assessed health, work productivity, and healthcare resource use. Improved management of these side effects or development of treatments with a better side effect profile may have a substantial humanistic and economic benefit.

ETR, TRA642. ELEVATIONS. METAL SIDING. OFFICE BUILDING (TRA647) AND ELECTRICAL ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

ETR, TRA-642. ELEVATIONS. METAL SIDING. OFFICE BUILDING (TRA-647) AND ELECTRICAL BUILDING (TRA-648) ATTACHED. KAISER ETR-5528-MTR-642-A-11, 11/1955. INL INDEX NO. 532-0642-00-486-100919, REV. 3. - Idaho National Engineering Laboratory, Test Reactor Area, Materials & Engineering Test Reactors, Scoville, Butte County, ID

ETR, TRA642. WALL SECTION DETAILS. METAL SIDING JOINS TO ELECTRICAL ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

ETR, TRA-642. WALL SECTION DETAILS. METAL SIDING JOINS TO ELECTRICAL BUILDING, OFFICE BUILDING, AND ROOF. KAISER ETR-5528-MTR-A-13, 11/1955. INL INDEX NO. 532-0642-00-486-100920, REV. 4. - Idaho National Engineering Laboratory, Test Reactor Area, Materials & Engineering Test Reactors, Scoville, Butte County, ID

75 FR 81711 - Notice of Receipt of Petition for Decision That Nonconforming 1991 Rice Beaufort Double Trailers...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-12-28

... reflectors, tail lamps, license plate lamps, rear side marker lamps, front side marker lamps, intermediate... information provided. Please see the Privacy Act heading below. Privacy Act: Anyone is able to search the... that you periodically search the Docket for new material. FOR FURTHER INFORMATION CONTACT: Coleman...

CANAL EMERGES FROM EAST SIDE OF MTR BUILDING. "EXTRA" LENGTH ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

CANAL EMERGES FROM EAST SIDE OF MTR BUILDING. "EXTRA" LENGTH WAS TO STORE SPENT FUEL THAT WOULD ACCUMULATE BEFORE THE CHEMICAL PROCESSING PLANT WAS READY TO PROCESS IT. INL NEGATIVE NO. 1659. Unknown Photographer, 3/9/1951 - Idaho National Engineering Laboratory, Test Reactor Area, Materials & Engineering Test Reactors, Scoville, Butte County, ID

48 CFR 52.204-4 - Printed or Copied Double-Sided on Recycled Paper.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 48 Federal Acquisition Regulations System 2 2010-10-01 2010-10-01 false Printed or Copied Double-Sided on Recycled Paper. 52.204-4 Section 52.204-4 Federal Acquisition Regulations System FEDERAL... and paper products, postconsumer material means “postconsumer fiber” defined by the U.S. Environmental...

Advanced Gradient Heating Facility

NASA Technical Reports Server (NTRS)

2004-01-01

The Advanced Gradient Heating Facility (AGHF) is a European Space Agency (ESA) developed hardware. The AGHF was flown on STS-78, which featured four European PI's and two NASA PI's. The AGHFsupports the production of advanced semiconductor materials and alloys using the directional process, which depends on establishing a hot side and a cold side in the sample.

Attention and Material-Specific Memory in Children with Lateralized Epilepsy

ERIC Educational Resources Information Center

Engle, Jennifer A.; Smith, Mary Lou

2010-01-01

Epilepsy is frequently associated with attention and memory problems. In adults, lateralization of seizure focus impacts the type of memory affected (left-sided lesions primarily impact verbal memory, while right-sided lesions primarily impact visual memory), but the relationship between seizure focus and the nature of the memory impairment is…

ETR BUILDING, TRA642, INTERIOR. CONSOLE FLOOR, SOUTH HALF. SOUTH SIDE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

ETR BUILDING, TRA-642, INTERIOR. CONSOLE FLOOR, SOUTH HALF. SOUTH SIDE OF ETR REACTOR, CAMERA FACING NORTH. CABINET CONTAINING "NUCLEAR INSTRUMENT SYSTEMS" IS RESTRICTED. INL NEGATIVE NO. HD46-18-4. Mike Crane, Photographer, 2/2005 - Idaho National Engineering Laboratory, Test Reactor Area, Materials & Engineering Test Reactors, Scoville, Butte County, ID

STORAGE AND RECIEVING, TRA662. ELEVATIONS. LOWBAY SECTION ON SOUTH SIDE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

STORAGE AND RECIEVING, TRA-662. ELEVATIONS. LOW-BAY SECTION ON SOUTH SIDE WAS FLAMMABLE STORAGE AREA. HUMMEL HUMMEL & JONES 1038-MTR-ETR-662-A-3, 6/1960. INL INDEX NO. 532-0653-00-381-102036, REV. 3. - Idaho National Engineering Laboratory, Test Reactor Area, Materials & Engineering Test Reactors, Scoville, Butte County, ID

30 CFR 57.22218 - Seals and stoppings (III, V-A, and V-B mines).

Code of Federal Regulations, 2013 CFR

2013-07-01

... materials may be used in face areas. (b) Exposed surfaces on the intake side of stoppings constructed of... construction shall be solid. (c) Exposed surfaces on the fresh air side of seals constructed of combustible... other coatings with equivalent fire resistance. Stoppings constructed to phenolic foam blocks at least...

30 CFR 57.22218 - Seals and stoppings (III, V-A, and V-B mines).

Code of Federal Regulations, 2014 CFR

2014-07-01

... materials may be used in face areas. (b) Exposed surfaces on the intake side of stoppings constructed of... construction shall be solid. (c) Exposed surfaces on the fresh air side of seals constructed of combustible... other coatings with equivalent fire resistance. Stoppings constructed to phenolic foam blocks at least...

30 CFR 57.22218 - Seals and stoppings (III, V-A, and V-B mines).

Code of Federal Regulations, 2012 CFR

2012-07-01

... materials may be used in face areas. (b) Exposed surfaces on the intake side of stoppings constructed of... construction shall be solid. (c) Exposed surfaces on the fresh air side of seals constructed of combustible... other coatings with equivalent fire resistance. Stoppings constructed to phenolic foam blocks at least...

Construction patterns of birds' nests provide insight into nest-building behaviours.

PubMed

Biddle, Lucia; Goodman, Adrian M; Deeming, D Charles

2017-01-01

Previous studies have suggested that birds and mammals select materials needed for nest building based on their thermal or structural properties, although the amounts or properties of the materials used have been recorded for only a very small number of species. Some of the behaviours underlying the construction of nests can be indirectly determined by careful deconstruction of the structure and measurement of the biomechanical properties of the materials used. Here we examined this idea in an investigation of Bullfinch ( Pyrrhula pyrrhula ) nests as a model for open-nesting songbird species that construct a "twig" nest, and tested the hypothesis that materials in different parts of nests serve different functions. The quantities of materials present in the nest base, sides and cup were recorded before structural analysis. Structural analysis showed that the base of the outer nests were composed of significantly thicker, stronger and more rigid materials compared to the side walls, which in turn were significantly thicker, stronger and more rigid than materials used in the cup. These results suggest that the placement of particular materials in nests may not be random, but further work is required to determine if the final structure of a nest accurately reflects the construction process.

Side Streams of Plant Food Processing As a Source of Valuable Compounds: Selected Examples.

PubMed

Schieber, Andreas

2017-02-28

Industrial processing of plant-derived raw materials generates enormous amounts of by-products. On one hand, these by-products constitute a serious disposal issue because they often emerge seasonally and are prone to microbial decay. On the other hand, they are an abundant source of valuable compounds, in particular secondary plant metabolites and cell wall materials, which may be recovered and used to functionalize foods and replace synthetic additives with ingredients of natural origin. This review covers 150 references and presents select studies performed between 2001 and 2016 on the recovery, characterization, and application of valuable constituents from grape pomace, apple pomace, potato peels, tomato pomace, carrot pomace, onion peels, by-products of citrus, mango, banana, and pineapple processing, side streams of olive oil production, and cereal by-products. The criteria used were economic importance, amounts generated, relevance of side streams as a source of valuable compounds, and reviews already published. Despite a plethora of studies carried out on the utilization of side streams, relatively few processes have yet found industrial application.

Mechanical membrane for the separation of a paramagnetic constituent from a fluid

DOEpatents

Maurice, David

2017-05-02

The disclosure provides an apparatus and method for the separation of a paramagnetic component from a mixture using a mechanical membrane apparatus. The mechanical membrane comprises a supporting material having a plurality of pores where each pore is surrounded by a plurality of magnetic regions. The magnetic regions augment a magnetic field on one side of the supporting material while mitigating the field to near zero on the opposite side. In operation, a flow of fluid such as air comprising a paramagnetic component such as O.sub.2 is directed toward the mechanical membrane, and the paramagnetic component is typically attracted toward a magnetic field surrounding a pore while dimagnetic components such as N.sub.2 are generally repelled. As some portion of the fluid passes through the plurality of magnetic apertures to the opposite side of the mechanical membrane, the mechanical membrane generates a fluid enriched in the paramagnetic component. Alternately, the magnetic field may act to repel the paramagnetic component while diamagnetic components such as N.sub.2 are generally unaffected and pass to the opposite side of the mechanical membrane.

Development of a Test for Evaluation of the Hydrothermal Stability of Sorbents Used in Closed-Loop CO2 Removal Systems

NASA Technical Reports Server (NTRS)

Knox, James C.; Gauto, Hernando; Miller, Lee A.

2015-01-01

The International Space Station Carbon Dioxide Removal Assembly uses zeolite 5A molecular sieve material packed into beds for the capture of cabin CO2. The beds are cyclically heated to drive off the CO2 and restore the removal capacity. Over time, the sorbent material has been found to break down resulting in dust that restricts flow through the beds. Humidity adsorbed in the 5A zeolite when it is heated is a suspected cause of this sorbent degradation. To evaluate the impact of adsorbed water during thermal cycling, the Hydrothermal Stability Test was developed. The test configuration provides comparative side-by-side flow restriction data for two sorbent materials at specifically controlled humidity levels. While the initial focus of the testing is on 5A zeolite materials currently used on the ISS, the system will also be used to evaluate future candidate materials. This paper describes the approach, the test system, current results, and future testing.

Impact analysis of side door of a car and bullet proof vest with material ‘SAM2X5-630’ using finite element analysis

NASA Astrophysics Data System (ADS)

Dhode, Trushant; Patil, Girish; Rajkumar, E.

2017-11-01

The components which are bound to impact are subjected to deformation even though it may be for a small scale. The efforts are always on for finding the best material to take impact that has no failure or moreover, less plastic deformation. A newly found material which is glass matrix steel named as ‘SAM2X5-630’ has astounding high elastic limit of 12.5GPa. Thus it can take powerful impact & regain its original shape avoiding the deformation of component under impact. The paper is focused on performing the Finite element analysis to assess the behaviour of ‘SAM2X5-630’ steel under impact loading of side door of car as well as impact of bullet on bulletproof jacket on which the material is assigned. The displacement or deformation occurred during impact is found to be lesser than known materials like Kevlar in bulletproof vest and Aluminium alloy in car door.

The effect of sawbolt length on the yield of pallet materials from small-diameter hardwood trees

Treesearch

E. Paul Craft

1982-01-01

From poletimber stand thinnings, 52 trees were bucked into 8-foot lengths, and 49 trees were felled and bucked into 10-foot lengths, The 8- and 10-foot pieces were sawed into pallet cants and side lumber suitable for pallet parts. The sawed yield, by tree, from each length category was compared to the predicted yield of the same trees if bucked into 4- and 6-foot bolts...

Electron beam therapy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Price, N.M.

An observed clinical side effect of total skin surface electron beam therapy is the patient's inability to perspire. An evaluation of eccrine sweat gland function was performed, utilizing acetylcholine chloride and a silicone impression material. The patient's inability to sweat after therapy, and recovery within a three- to six-month period after therapy was demonstrated. This phenomenon should be appreciated by both the physician and the patient prior to electron beam therapy in order to avoid the potential complications of this condition.

Special Operations Forces Aviation on a Shoestring Budget: An Effectiveness Analysis of Light and Medium Fixed Wing Aircraft

DTIC Science & Technology

2012-12-01

C2 Command and Control CAIG Cost Analysis Improvement Group CAS Close Air Support CASA Construcciones Aeronáuticas SA CLS Contract...Commercially Available Off-the-Shelf Commercially available off-the shelf (COTS) is defined as any item of supply (including construction material...uses are found for old weapons that were constructed for use in industrial war against soldiers and heavy armament. 6. The sides are mostly non

Device for reducing vehicle aerodynamic resistance

DOEpatents

Graham, Sean C.

2005-02-15

A device for a vehicle with a pair of swinging rear doors, which converts flat sheets of pliable material hinged to the sides of the vehicle adjacent the rear thereof into effective curved airfoils that reduce the aerodynamic resistance of the vehicle, when the doors are closed by hand, utilizing a plurality of stiffeners disposed generally parallel to the doors and affixed to the sheets and a plurality of collapsible tension bearings struts attached to each stiffener and the adjacent door.

Effects of Smoke on Functional Circuits

DTIC Science & Technology

1997-10-01

functional boards consisted of four layers ; that is, there were two pieces of FR-4* insulated circuit board material that were laminated together, each with...traces on both sides (three layers of dielectric in all). The layers were electrically connected by drilling holes into the circuit board and...allowing solder to flow through the holes and form "vias." For many of the circuits, one of the middle layers served as a ground plane, while the other

Finger-attachment device for the feedback of gripping and pulling force in a manipulating system for brain tumor resection.

PubMed

Chinbe, Hiroyuki; Yoneyama, Takeshi; Watanabe, Tetsuyou; Miyashita, Katsuyoshi; Nakada, Mitsutoshi

2018-01-01

Development and evaluation of an effective attachment device for a bilateral brain tumor resection robotic surgery system based on the sensory performance of the human index finger in order to precisely detect gripping- and pulling-force feedback. First, a basic test was conducted to investigate the performance of the human index finger in the gripping- and pulling-force feedback system. Based on the test result, a new finger-attachment device was designed and constructed. Then, discrimination tests were conducted to assess the pulling force and the feedback on the hardness of the gripped material. The results of the basic test show the application of pulling force on the side surface of the finger has an advantage to distinguish the pulling force when the gripping force is applied on the finger-touching surface. Based on this result, a finger-attachment device that applies a gripping force on the finger surface and pulling force on the side surface of the finger was developed. By conducting a discrimination test to assess the hardness of the gripped material, an operator can distinguish whether the gripped material is harder or softer than a normal brain tissue. This will help in confirming whether the gripped material is a tumor. By conducting a discrimination test to assess the pulling force, an operator can distinguish the pulling-force resistance when attempting to pull off the soft material. Pulling-force feedback may help avoid the breaking of blood pipes when they are trapped in the gripper or attached to the gripped tissue. The finger-attachment device that was developed for detecting gripping- and pulling-force feedback may play an important role in the development of future neurosurgery robotic systems for precise and safe resection of brain tumors.

Decreasing the Burden of Side Effects Through Positive Message Framing: an Experimental Proof-of-Concept Study.

PubMed

Wilhelm, Marcel; Rief, Winfried; Doering, Bettina K

2018-05-21

Informing patients about treatment side effects increases the occurrence and intensity of side effects. Since the obligatory informed consent procedure in drug treatments requires transparency and nocebo research suggests that the informed consent of a drug leads to an increased occurrence of the mentioned side effects, the aim of this proof of concept study was to determine the effect of two different framings of informed consent on the occurrence, intensity, and perceived threat of side effects. Healthy male participants (n = 80) were randomized to one of two framing groups. The positive framing group was informed that the common side effect dizziness was a sign that the drug had started to work, while the neutral framing group was told that dizziness is an unpleasant but well-known side effect. Side effects were measured after the administration of metoprolol, an antihypertensive agent. Post hoc moderator analyses investigated the effect of pre-existing negative beliefs about the general harm of medication on the framing manipulation. Metoprolol-specific drug-attributed side effects were rated significantly less threatening in the positive framing group. The between-group effect size (Cohen's d) was small (d = 0.38, p = 0.049). Exploratory post hoc moderator analyses suggest that participants who believed that medication is a source of harmful effects benefited from positive framing, compared to neutral framing of drug-attributed side effects. Positive framing was partially effective in decreasing specific side effect measures, particularly among participants with a tendency to believe that medicine is harmful. Informed consent procedures should therefore be personalized, focusing on patients with negative treatment beliefs.

Radial modes of laterally stiffened piezoelectric disc transducers for ultrasonic collimated beam generation

DOE PAGES

Chillara, Vamshi Krishna; Pantea, Cristian; Sinha, Dipen N.

2017-07-15

Here, we numerically investigate the resonance and vibration characteristics of radial modes of laterally stiffened piezoelectric disc transducers. Lateral stiffening is modeled using a spring and vibration characteristics of the piezo-disc are investigated with increasing lateral stiffness. It is found that the resonant frequency response of the radial modes follows an asymptotic behavior approaching that of a clamped disc with increasing lateral stiffness. The radial mode vibration pattern of the discs is also found to be affected by lateral stiffness. While the vibration pattern of a free disc corresponds to a Bessel function, laterally stiffened discs show edge-effects where theymore » depart from the Bessel-like behavior. In addition, a fully clamped piezo-disc is found to have an extra side-lobe when compared to a free disc. Ultrasonic beam profiles generated from radial modes of laterally stiffened discs are numerically investigated. It is found that the free piezo-disc generates a Bessel beam that has multiple side-lobes. Increasing the lateral stiffness results in a significant reduction of side-lobes in the beam profile. This technique of generating a collimated beam with side-lobe reduction finds significant applications in imaging through concrete, drilling mud, and other highly attenuating materials.« less

A self-cleaning Li-S battery enabled by a bifunctional redox mediator

NASA Astrophysics Data System (ADS)

Ren, Y. X.; Zhao, T. S.; Liu, M.; Zeng, Y. K.; Jiang, H. R.

2017-09-01

The polysulfide shuttle effect and lithium dendrite growth in lithium-sulfur (Li-S) batteries can repeatedly breach the anodic solid electrolyte interphase (SEI) over cycling. As a result, irreversible short-chain sulfide side products (Li2Sx, x = 1, 2) keep depositing on the Li anode, leading to the active material loss, increasing the Li+ transport resistance, and thereby reducing the cycle life. In this work, indium iodide (InI3) is investigated as a bifunctional electrolyte additive for Li-S batteries to protect the Li anode and decompose the side products spontaneously. On the one hand, Indium (In) is electrodeposited onto the Li anode prior to Li plating during the initial charging process, forming a chemically and mechanically stable SEI to prevent the Li anode from reacting with soluble polysulfide species to form Li2Sx (x = 1, 2) side products. On the other hand, by adequately overcharging the battery, the triiodide/iodide redox mediator is capable of chemically transforming side products deposited on the Li anode and separator into soluble polysulfides, which can be recycled by the cathode. It is shown that the battery with the InI3 additive exhibits a prolonged cycle life, and is capable of retrieving its capacity by a facile overcharging process.

Combined use of alcohol and energy drinks: Dose relationship with self-reported physiological stimulation and sedation side effects.

PubMed

Droste, Nicolas; Peacock, Amy; Bruno, Raimondo; Pennay, Amy; Zinkiewicz, Lucy; Lubman, Dan I; Miller, Peter

2017-08-01

Negative physiological stimulation and sedation side effects are experienced by a significant proportion of consumers who consume alcohol mixed with energy drinks (AmED). Few studies have compared the frequency of side effects between sessions of AmED and sessions of alcohol only within-subject, and none have explored a dose relationship. Explore the occurrence of self-reported physiological stimulant and sedative side effects between sessions of AmED and alcohol only, and at varying ED dosage levels within AmED sessions. A convenience sample of 2953 residents of New South Wales, Australia completed an online survey. N=731 AmED users reported daily caffeine intake, typical alcohol and AmED consumption, and past 12-month experience of physiological stimulation and sedation side effects during AmED and alcohol only sessions. Within-subject analyses compared occurrence of side effects between session types. Hierarchical binary logistic regression analyses explored the association of ED dose during AmED sessions with the experience of physiological side effects. There were greater odds of most stimulant side effects, and lower odds of sedation side effects, during AmED sessions compared to alcohol only sessions. Compared to one ED, consumption of three or more EDs was significantly associated with the majority of both stimulant and alcohol intoxication side effects after controlling for demographics and consumption covariates. AmED is associated with perceived changes in physiological stimulant and sedation side effects of alcohol. Experience of side effects is positively associated with ED dosage. Future research should account for varying ED dosage, and reflect real world consumption levels. Copyright © 2017 Elsevier Ltd. All rights reserved.

Multilayer composite material and method for evaporative cooling

NASA Technical Reports Server (NTRS)

Buckley, Theresa M. (Inventor)

2002-01-01

A multilayer composite material and method for evaporative cooling of a person employs an evaporative cooling liquid that changes phase from a liquid to a gaseous state to absorb thermal energy. The evaporative cooling liquid is absorbed into a superabsorbent material enclosed within the multilayer composite material. The multilayer composite material has a high percentage of the evaporative cooling liquid in the matrix. The cooling effect can be sustained for an extended period of time because of the high percentage of phase change liquid that can be absorbed into the superabsorbent. Such a composite can be used for cooling febrile patients by evaporative cooling as the evaporative cooling liquid in the matrix changes from a liquid to a gaseous state to absorb thermal energy. The composite can be made with a perforated barrier material around the outside to regulate the evaporation rate of the phase change liquid. Alternatively, the composite can be made with an imperveous barrier material or semipermeable membrane on one side to prevent the liquid from contacting the person's skin. The evaporative cooling liquid in the matrix can be recharged by soaking the material in the liquid. The multilayer composite material can be fashioned into blankets, garments and other articles.

Computational Simulations of Inferior Vena Cava (IVC) Filter Placement and Hemodynamics in Patient-Specific Geometries

NASA Astrophysics Data System (ADS)

Aycock, Kenneth; Sastry, Shankar; Kim, Jibum; Shontz, Suzanne; Campbell, Robert; Manning, Keefe; Lynch, Frank; Craven, Brent

2013-11-01

A computational methodology for simulating inferior vena cava (IVC) filter placement and IVC hemodynamics was developed and tested on two patient-specific IVC geometries: a left-sided IVC, and an IVC with a retroaortic left renal vein. Virtual IVC filter placement was performed with finite element analysis (FEA) using non-linear material models and contact modeling, yielding maximum vein displacements of approximately 10% of the IVC diameters. Blood flow was then simulated using computational fluid dynamics (CFD) with four cases for each patient IVC: 1) an IVC only, 2) an IVC with a placed filter, 3) an IVC with a placed filter and a model embolus, all at resting flow conditions, and 4) an IVC with a placed filter and a model embolus at exercise flow conditions. Significant hemodynamic differences were observed between the two patient IVCs, with the development of a right-sided jet (all cases) and a larger stagnation region (cases 3-4) in the left-sided IVC. These results support further investigation of the effects of IVC filter placement on a patient-specific basis.

Analytical Modeling of a Double-Sided Flux Concentrating E-Core Transverse Flux Machine with Pole Windings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Muljadi, Eduard; Hasan, Iftekhar; Husain, Tausif

In this paper, a nonlinear analytical model based on the Magnetic Equivalent Circuit (MEC) method is developed for a double-sided E-Core Transverse Flux Machine (TFM). The proposed TFM has a cylindrical rotor, sandwiched between E-core stators on both sides. Ferrite magnets are used in the rotor with flux concentrating design to attain high airgap flux density, better magnet utilization, and higher torque density. The MEC model was developed using a series-parallel combination of flux tubes to estimate the reluctance network for different parts of the machine including air gaps, permanent magnets, and the stator and rotor ferromagnetic materials, in amore » two-dimensional (2-D) frame. An iterative Gauss-Siedel method is integrated with the MEC model to capture the effects of magnetic saturation. A single phase, 1 kW, 400 rpm E-Core TFM is analytically modeled and its results for flux linkage, no-load EMF, and generated torque, are verified with Finite Element Analysis (FEA). The analytical model significantly reduces the computation time while estimating results with less than 10 percent error.« less

Brushless machine having ferromagnetic side plates and side magnets

DOEpatents

Hsu, John S

2012-10-23

An apparatus is provided having a cylindrical stator and a rotor that is spaced from a stator to define an annular primary air gap that receives AC flux from the stator. The rotor has a plurality of longitudinal pole portions disposed parallel to the axis of rotation and alternating in polarity around a circumference of the rotor. Each longitudinal pole portion includes portions of permanent magnet (PM) material and at least one of the longitudinal pole portions has a first end and an opposing second end and a side magnet is disposed adjacent the first end and a side pole is disposed adjacent the second end.

Enhanced heat transfer surface for cast-in-bump-covered cooling surfaces and methods of enhancing heat transfer

DOEpatents

Chiu, Rong-Shi Paul; Hasz, Wayne Charles; Johnson, Robert Alan; Lee, Ching-Pang; Abuaf, Nesim

2002-01-01

An annular turbine shroud separates a hot gas path from a cooling plenum containing a cooling medium. Bumps are cast in the surface on the cooling side of the shroud. A surface coating overlies the cooling side surface of the shroud, including the bumps, and contains cooling enhancement material. The surface area ratio of the cooling side of the shroud with the bumps and coating is in excess of a surface area ratio of the cooling side surface with bumps without the coating to afford increased heat transfer across the element relative to the heat transfer across the element without the coating.

Redox-responsive mesoporous selenium delivery of doxorubicin targets MCF-7 cells and synergistically enhances its anti-tumor activity.

PubMed

Zhao, Shuang; Yu, Qianqian; Pan, Jiali; Zhou, Yanhui; Cao, Chengwen; Ouyang, Jian-Ming; Liu, Jie

2017-05-01

To reduce the side effects and enhance the anti-tumor activities of anticancer drugs in the clinic, the use of nano mesoporous materials, with mesoporous silica (MSN) being the best-studied, has become an effective method of drug delivery. In this study, we successfully synthesized mesoporous selenium (MSe) nanoparticles and first introduced them to the field of drug delivery. Loading MSe with doxorubicin (DOX) is mainly driven by the physical adsorption mechanism of the mesopores, and our results demonstrated that MSe could synergistically enhance the antitumor activity of DOX. Coating the surface of MSe@DOX with Human serum albumin (HSA) generated a unique redox-responsive nanoparticle (HSA-MSe@DOX) that demonstrated glutathione-dependent drug release, increased tumor-targeting effects and enhanced cellular uptake throug nanoparticle interact with SPARC in MCF-7 cells. In vitro, HSA-MSe@DOX prominently induced cancer cell toxicity by synergistically enhancing the effects of MSe and DOX. Moreover, HSA-MSe@DOX possessed tumor-targeting abilities in tumor-bearing nude mice and not only decreased the side effects associated with DOX, but also enhanced its antitumor activity. Therefore, HSA-MSe@DOX is a promising new drug that warrants further evaluation in the treatments of tumors. To reduce the side effects and enhance the anti-tumor activities of anticancer drugs, we successfully synthesized mesoporous selenium (MSe) nanoparticles and first introduced them to the field of drug delivery. Loading MSe with doxorubicin (DOX) is mainly driven by the physical adsorption mechanism of the mesopores. Coating the surface of MSe@DOX with Human serum albumin (HSA) generated a unique redox-responsive nanoparticle (HSA-MSe@DOX) that demonstrated glutathione-dependent drug release, increased tumor-targeting effects and enhanced cellular uptake throug nanoparticle interact with SPARC in MCF-7 cells. In vitro and in vivo, HSA-MSe@DOX possessed tumor-targeting abilities and not only decreased the side effects associated with DOX, but also enhanced its antitumor activity. Therefore, HSA-MSe@DOX is a promising new drug that warrants further evaluation in the treatments of tumors. Copyright © 2017 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

The use of human chorionic gonadotropin (HCG) for penile reconstruction in bladder exstrophy and total epispadias patients.

PubMed

Makedonsky, I A

2006-12-01

The effect of intramuscular human chorionic gonadotropin (HCG) administration on penile enlargement before genital surgery, its influence on penile skin histology and testicular descent were investigated. We examined 45 male patients (median age, 8 months; range 3-28) with total epispadias and classic bladder exstrophy, combined with cryptorchidism. 30 patients were administered 250-500 IU HCG intramuscularly 2 times per week for 3 weeks before reconstructive surgery. Skin biopsies were obtained for human epidermal growth factor (EGF) and human epidermal growth factor receptor (Her2/neu) determination. Skin specimens of the prepuce of 18 circumcised patients were used as controls. Post treatment testicle position was evaluated. HCG caused a mean increase in penile length of 1.8 cm (p < 0.01) and in circumference of 1.2 cm (p < 0.05) as well as improved local vascularity in all patients. Compared to the controls, the penile skin of exstrophy/epispadias patients showed a significant decrease in the average amount per field of EGF and Her2/neu positive material (controls 81% [mean 79, SE 2.3] vs. 31% [mean 28, SE 3.6; p < 0.001]). Treatment with HCG led to an increase in average EGF and Her2/neu positive material by 10% (mean 8, SE 2; p < 0.05). The potential side effects of HCG treatment were monitored 3 to 6 months postoperatively. Basal testosterone and LH levels were obtained in patients before and during therapy and postoperatively. Testicular descent was achieved in 21 patients (70%). No significant side effects or complications were encountered in any of our patients. Mean EGF and Her2/neu values are decreased in the penile skin of exstrophy/epispadias patients. The use of preoperative HCG administration leads to an increase in EGF and Her2/neu values and significantly contributes to successful reconstruction in these patients, especially in cases with a paucity of penile skin and in patients who have undergone previous repairs. Temporary penile stimulation by HCG in patients with bladder exstrophy combined with cryptorchidism allows the penile operation to be carried out earlier and contributes to testicular descent while demonstrating negligible side effects.

Treatment factors affecting longitudinal quality of life in new onset pediatric epilepsy.

PubMed

Modi, Avani C; Ingerski, Lisa M; Rausch, Joseph R; Glauser, Tracy A

2011-05-01

Recognizing the importance of patient-reported outcomes, this longitudinal, prospective study examined: Changes in health-related quality of life (HRQOL) over seven months following antiepileptic drug (AED) initiation and the relationship of seizures, AED side-effects, and AED type to HRQOL. Parents of 124 children with newly diagnosed epilepsy completed measures of HRQOL and side-effects at each clinic visit. Treatment information was also collected. HRQOL remained stable over time; however, seizures and AED side-effects significantly affected multiple HRQOL domains. Higher seizure activity was associated with decreased Physical HRQOL. Side-effects were negatively associated with all HRQOL domains. Children taking carbamazepine who experienced higher side-effects early in therapy demonstrated declining emotional functioning compared to children experiencing no/some side-effects. AED side-effects, AED type, and seizure frequency were associated with longitudinal HRQOL in children with newly-diagnosed epilepsy. Routine assessment of AED side-effects and HRQOL may be useful for clinical decision making.

Effects of culture-sensitive adaptation of patient information material on usefulness in migrants: a multicentre, blinded randomised controlled trial.

PubMed

Hölzel, Lars P; Ries, Zivile; Kriston, Levente; Dirmaier, Jörg; Zill, Jördis M; Rummel-Kluge, Christine; Niebling, Wilhelm; Bermejo, Isaac; Härter, Martin

2016-11-23

To evaluate the usefulness of culture-sensitive patient information material compared with standard translated material. Multicentre, double-blind randomised controlled trial. 37 primary care practices. 435 adult primary care patients with a migration background with unipolar depressive disorder or non-specific chronic low back pain were randomised. Patients who were unable to read in the language of their respective migration background were excluded. Sufficient data were obtained from 203 women and 106 men. The largest group was of Russian origin (202 patients), followed by those of Turkish (52), Polish (30) and Italian (25) origin. Intervention group: provision of culture-sensitive adapted material. provision of standard translated material. Primary outcome: patient-rated usefulness (USE) assessed immediately after patients received the material. patient-rated usefulness after 8 weeks and 6 months, symptoms of depression (PHQ-9), back pain (Back Pain Core Set) and quality of life (WHO-5) assessed at all time points. Usefulness was found to be significantly higher (t=1.708, one-sided p=0.04) in the intervention group (USE-score=65.08, SE=1.43), compared with the control group (61.43, SE=1.63), immediately after patients received the material, in the intention-to-treat analysis, with a mean difference of 3.65 (one-sided 95% lower confidence limit=0.13). No significant differences were found for usefulness at follow-up (p=0.16, p=0.71). No significant effect was found for symptom severity in depression (p=0.95, p=0.66, p=0.58), back pain (p=0.40, p=0.45, p=0.32) or quality of life (p=0.76, p=0.86, p=0.21), either immediately after receiving the material, or at follow-up (8 weeks; 6 months). Patients with a lower level of dominant society immersion benefited substantially and significantly more from the intervention than patients with a high level of immersion (p=0.005). Cultural adaptation of patient information material provides benefits over high quality translations. Clinicians are encouraged to use culture-sensitive material in their consultations, particularly with low-acculturated patients. German Register for Clinical Trials: DRKS00004241, Universal Trial Number: U1111-1135-8043, Results. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/.

Method and apparatus for detecting flaws in conductive material

DOEpatents

Hockey, Ronald L.; Riechers, Douglas M.

1998-01-01

The present invention uses a magnet in relative motion to a conductive material, and a coil that is stationary with respect to the magnet to measure perturbation or variation in the magnetic field in the presence of an inclusion. The magnet and coil sensor may be on the same side of the conductive material.

40 CFR 503.21 - Special definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... strata on the other side. (g) Final cover is the last layer of soil or other material placed on a sewage... soil or other material used to cover sewage sludge placed on an active sewage sludge unit. (e... collect and remove leachate from a sewage sludge unit. (j) Liner is soil or synthetic material that has a...

40 CFR 503.21 - Special definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... strata on the other side. (g) Final cover is the last layer of soil or other material placed on a sewage... soil or other material used to cover sewage sludge placed on an active sewage sludge unit. (e... collect and remove leachate from a sewage sludge unit. (j) Liner is soil or synthetic material that has a...

40 CFR 503.21 - Special definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... strata on the other side. (g) Final cover is the last layer of soil or other material placed on a sewage... soil or other material used to cover sewage sludge placed on an active sewage sludge unit. (e... collect and remove leachate from a sewage sludge unit. (j) Liner is soil or synthetic material that has a...

40 CFR 503.21 - Special definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... strata on the other side. (g) Final cover is the last layer of soil or other material placed on a sewage... soil or other material used to cover sewage sludge placed on an active sewage sludge unit. (e... collect and remove leachate from a sewage sludge unit. (j) Liner is soil or synthetic material that has a...

40 CFR 503.21 - Special definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... strata on the other side. (g) Final cover is the last layer of soil or other material placed on a sewage... soil or other material used to cover sewage sludge placed on an active sewage sludge unit. (e... collect and remove leachate from a sewage sludge unit. (j) Liner is soil or synthetic material that has a...

Investigations of Heat Transfer in Vacuum between Room Temperature and 80 K

NASA Astrophysics Data System (ADS)

Hooks, J.; Demko, J. A.; E Fesmire, J.; Matsumoto, T.

2017-12-01

The heat transfer between room temperature and 80 K is controlled using various insulating material combinations. The modes of heat transfer are well established to be conduction and thermal radiation when in a vacuum. Multi-Layer Insulation (MLI) in a vacuum has long been the best approach. Typically this layered system is applied to the cold surface. This paper investigates the application of MLI to both the cold and warm surface to see whether there is a significant difference. In addition if MLI is on the warm surface, the cold side of the MLI may be below the critical temperature of some high temperature superconducting (HTS) materials. It has been proposed that HTS materials can serve to block thermal radiation. An experiment is conducted to measure this effect. Boil-off calorimetry is the method of measuring the heat transfer.

[Treatment side effects and compliance in patients with depression].

PubMed

Petrova, N N; Kucher, E O

2012-01-01

The impact of treatment side-effects on the compliance was studied in 85 depressive patients with different mental disorders - recurrent depressive disorder, postschizophrenic depression and organic affective disorder. The comparison of objective and subjective evaluations of compliance and a comparative analysis of the level of compliance, with its dependence on the treatment specifics, in different diseases were done. A significant role of efficacy and treatment side-effects was identified. The levels of "mental" and "autonomous" side-effects were highest in the treatment of depression: patients with postschizophrenic depression had the highest risk in respect of maintenance treatment; patients with recurrent depressive disorder and organic (affective) disorder were more tolerant to the treatment side-effects and their treatment, including the maintenance therapy, was rather effective. The compliance of all patients with depression was negatively correlated with the severity of side-effects of pharmacotherapy. The greatest side-effects and the lowest level of compliance were observed in the complex treatment with antidepressants and atypical neuroleptics. The effect of side-effects on the compliance was dependent on their severity and subjective tolerability and, to a lesser extent, on the amount of drugs.

Evaluation of polymer based third order nonlinear integrated optics devices

NASA Astrophysics Data System (ADS)

Driessen, A.; Hoekstra, H. J. W. M.; Blom, F. C.; Horst, F.; Krijnen, G. J. M.; van Schoot, J. B. P.; Lambeck, P. V.; Popma, Th. J. A.; Diemeer, M. B.

1998-01-01

Nonlinear polymers are promising materials for high speed active integrated optics devices. In this paper we evaluate the perspectives polymer based nonlinear optical devices can offer. Special attention is directed to the materials aspects. In our experimental work we applied mainly Akzo Nobel DANS side-chain polymer that exhibits large second and third order coefficients. This material has been characterized by third harmonic generation, z-scan and pump-probe measurements. In addition, various waveguiding structures have been used to measure the nonlinear absorption (two photon absorption) on a ps time-scale. Finally an integrated optics Mach Zehnder interferometer has been realized and evaluated. It is shown that the DANS side-chain polymer has many of the desired properties: the material is easily processable in high-quality optical waveguiding structures, has low linear absorption and its nonlinearity has a pure electronic origin. More materials research has to be done to arrive at materials with higher nonlinear coefficients to allow switching at moderate light intensity ( < 1 W peak power) and also with lower nonlinear absorption coefficients.

Solid oxide fuel cell having compound cross flow gas patterns

DOEpatents

Fraioli, A.V.

1983-10-12

A core construction for a fuel cell is disclosed having both parallel and cross flow passageways for the fuel and the oxidant gases. Each core passageway is defined by electrolyte and interconnect walls. Each electrolyte wall consists of cathode and anode materials sandwiching an electrolyte material. Each interconnect wall is formed as a sheet of inert support material having therein spaced small plugs of interconnect material, where cathode and anode materials are formed as layers on opposite sides of each sheet and are electrically connected together by the interconnect material plugs. Each interconnect wall in a wavy shape is connected along spaced generally parallel line-like contact areas between corresponding spaced pairs of generally parallel electrolyte walls, operable to define one tier of generally parallel flow passageways for the fuel and oxidant gases. Alternate tiers are arranged to have the passageways disposed normal to one another. Solid mechanical connection of the interconnect walls of adjacent tiers to the opposite sides of the common electrolyte wall therebetween is only at spaced point-like contact areas, 90 where the previously mentioned line-like contact areas cross one another.

Solid oxide fuel cell having compound cross flow gas patterns

DOEpatents

Fraioli, Anthony V.

1985-01-01

A core construction for a fuel cell is disclosed having both parallel and cross flow passageways for the fuel and the oxidant gases. Each core passageway is defined by electrolyte and interconnect walls. Each electrolyte wall consists of cathode and anode materials sandwiching an electrolyte material. Each interconnect wall is formed as a sheet of inert support material having therein spaced small plugs of interconnect material, where cathode and anode materials are formed as layers on opposite sides of each sheet and are electrically connected together by the interconnect material plugs. Each interconnect wall in a wavy shape is connected along spaced generally parallel line-like contact areas between corresponding spaced pairs of generally parallel electrolyte walls, operable to define one tier of generally parallel flow passageways for the fuel and oxidant gases. Alternate tiers are arranged to have the passageways disposed normal to one another. Solid mechanical connection of the interconnect walls of adjacent tiers to the opposite sides of the common electrolyte wall therebetween is only at spaced point-like contact areas, 90 where the previously mentioned line-like contact areas cross one another.

Polarization-based and specular-reflection-based noncontact latent fingerprint imaging and lifting

NASA Astrophysics Data System (ADS)

Lin, Shih-Schön; Yemelyanov, Konstantin M.; Pugh, Edward N., Jr.; Engheta, Nader

2006-09-01

In forensic science the finger marks left unintentionally by people at a crime scene are referred to as latent fingerprints. Most existing techniques to detect and lift latent fingerprints require application of a certain material directly onto the exhibit. The chemical and physical processing applied to the fingerprint potentially degrades or prevents further forensic testing on the same evidence sample. Many existing methods also have deleterious side effects. We introduce a method to detect and extract latent fingerprint images without applying any powder or chemicals on the object. Our method is based on the optical phenomena of polarization and specular reflection together with the physiology of fingerprint formation. The recovered image quality is comparable to existing methods. In some cases, such as the sticky side of tape, our method shows unique advantages.

49 CFR 572.40 - Incorporated materials.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 49 Transportation 7 2013-10-01 2013-10-01 false Incorporated materials. 572.40 Section 572.40 Transportation Other Regulations Relating to Transportation (Continued) NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) ANTHROPOMORPHIC TEST DEVICES Side Impact Dummy 50th...

49 CFR 572.110 - Materials incorporated by reference.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 49 Transportation 7 2014-10-01 2014-10-01 false Materials incorporated by reference. 572.110 Section 572.110 Transportation Other Regulations Relating to Transportation (Continued) NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) ANTHROPOMORPHIC TEST DEVICES Side...

49 CFR 572.40 - Incorporated materials.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 49 Transportation 7 2014-10-01 2014-10-01 false Incorporated materials. 572.40 Section 572.40 Transportation Other Regulations Relating to Transportation (Continued) NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) ANTHROPOMORPHIC TEST DEVICES Side Impact Dummy 50th...

49 CFR 572.110 - Materials incorporated by reference.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 49 Transportation 7 2013-10-01 2013-10-01 false Materials incorporated by reference. 572.110 Section 572.110 Transportation Other Regulations Relating to Transportation (Continued) NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) ANTHROPOMORPHIC TEST DEVICES Side...

49 CFR 572.40 - Incorporated materials.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 49 Transportation 7 2012-10-01 2012-10-01 false Incorporated materials. 572.40 Section 572.40 Transportation Other Regulations Relating to Transportation (Continued) NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) ANTHROPOMORPHIC TEST DEVICES Side Impact Dummy 50th...

49 CFR 572.110 - Materials incorporated by reference.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 49 Transportation 7 2012-10-01 2012-10-01 false Materials incorporated by reference. 572.110 Section 572.110 Transportation Other Regulations Relating to Transportation (Continued) NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) ANTHROPOMORPHIC TEST DEVICES Side...

Exploring the associations between drug side-effects and therapeutic indications.

PubMed

Wang, Fei; Zhang, Ping; Cao, Nan; Hu, Jianying; Sorrentino, Robert

2014-10-01

Drug therapeutic indications and side-effects are both measurable patient phenotype changes in response to the treatment. Inferring potential drug therapeutic indications and identifying clinically interesting drug side-effects are both important and challenging tasks. Previous studies have utilized either chemical structures or protein targets to predict indications and side-effects. In this study, we compared drug therapeutic indication prediction using various information including chemical structures, protein targets and side-effects. We also compared drug side-effect prediction with various information sources including chemical structures, protein targets and therapeutic indication. Prediction performance based on 10-fold cross-validation demonstrates that drug side-effects and therapeutic indications are the most predictive information source for each other. In addition, we extracted 6706 statistically significant indication-side-effect associations from all known drug-disease and drug-side-effect relationships. We further developed a novel user interface that allows the user to interactively explore these associations in the form of a dynamic bipartitie graph. Many relationship pairs provide explicit repositioning hypotheses (e.g., drugs causing postural hypotension are potential candidates for hypertension) and clear adverse-reaction watch lists (e.g., drugs for heart failure possibly cause impotence). All data sets and highly correlated disease-side-effect relationships are available at http://astro.temple.edu/∼tua87106/druganalysis.html. Copyright © 2014 Elsevier Inc. All rights reserved.

Lunar impact basins and crustal heterogeneity - New western limb and far side data from Galileo

NASA Technical Reports Server (NTRS)

Belton, Michael J. S.; Head, James W., III; Pieters, Carle M.; Greeley, Ronald; Mcewen, Alfred S.; Neukum, Gerhard; Klaasen, Kenneth P.; Anger, Clifford D.; Carr, Michael H.; Chapman, Clark R.

1992-01-01

Multispectral images of the lunar western limb and far side obtained from Galileo reveal the compositional nature of several prominent lunar features and provide new information on lunar evolution. The data reveal that the ejecta from the Orientale impact basin (900 kilometers in diameter) lying outside the Cordillera Mountains was excavated from the crust, not the mantle, and covers pre-Orientale terrain that consisted of both highland materials and relatively large expanses of ancient mare basalts. The inside of the far side South Pole-Aitken basin (greater than 2000 kilometers in diameter) has low albedo, red color, and a relatively high abundance of iron- and magnesium-rich materials. These features suggest that the impact may have penetrated into the deep crust or lunar mantle or that the basin contains ancient mare basalts that were later covered by highlands ejecta.

Characterizing the boundary lateral to the shear direction of deformation twins in magnesium

DOE PAGES

Liu, Y.; Li, N.; Shao, S.; ...

2016-06-01

The three-dimensional nature of twins, especially the atomic structures and motion mechanisms of the boundary lateral to the shear direction of the twin, has never been characterized at the atomic level, because such boundary is, in principle, crystallographically unobservable. We thus refer to it here as the dark side of the twin. Here, using high-resolution transmission electron microscopy and atomistic simulations, we characterize the dark side of {101 ⁻2} deformation twins in magnesium. It is found that the dark side is serrated and comprised of {101 ⁻2} coherent twin boundaries and semi-coherent twist prismatic–prismatic {211 ⁻0} boundaries that control twinmore » growth. The conclusions we find in this work apply to the same twin mode in other hexagonal close-packed materials, and the conceptual ideas discussed here should hold for all twin modes in crystalline materials.« less

Lunar impact basins and crustal heterogeneity: New western limb and far side data from galileo

USGS Publications Warehouse

Belton, M.J.S.; Head, J. W.; Pieters, C.M.; Greeley, R.; McEwen, A.S.; Neukum, G.; Klaasen, K.P.; Anger, C.D.; Carr, M.H.; Chapman, C.R.; Davies, M.E.; Fanale, F.P.; Gierasch, P.J.; Greenberg, R.; Ingersoll, A.P.; Johnson, T.; Paczkowski, B.; Pilcher, C.B.; Veverka, J.

1992-01-01

Multispectral images of the lunar western limb and far side obtained from Galileo reveal the compositional nature of several prominent lunar features and provide new information on lunar evolution. The data reveal that the ejecta from the Orientale impact basin (900 kilometers in diameter) lying outside the Cordillera Mountains was excavated from the crust, not the mantle, and covers pre-Orientale terrain that consisted of both highland materials and relatively large expanses of ancient mare basalts. The inside of the far side South Pole-Aitken basin (>2000 kilometers in diameter) has low albedo, red color, and a relatively high abundance of iron- and magnesium-rich materials. These features suggest that the impact may have penetrated into the deep crust or lunar mantle or that the basin contains ancient mare basalts that were later covered by highlands ejecta.

Apparatus and method for continuous production of materials

DOEpatents

Chang, Chih-hung; Jin, Hyungdae

2014-08-12

Embodiments of a continuous-flow injection reactor and a method for continuous material synthesis are disclosed. The reactor includes a mixing zone unit and a residence time unit removably coupled to the mixing zone unit. The mixing zone unit includes at least one top inlet, a side inlet, and a bottom outlet. An injection tube, or plurality of injection tubes, is inserted through the top inlet and extends past the side inlet while terminating above the bottom outlet. A first reactant solution flows in through the side inlet, and a second reactant solution flows in through the injection tube(s). With reference to nanoparticle synthesis, the reactant solutions combine in a mixing zone and form nucleated nanoparticles. The nucleated nanoparticles flow through the residence time unit. The residence time unit may be a single conduit, or it may include an outer housing and a plurality of inner tubes within the outer housing.

High-efficiency neutron detectors and methods of making same

DOEpatents

McGregor, Douglas S.; Klann, Raymond

2007-01-16

Neutron detectors, advanced detector process techniques and advanced compound film designs have greatly increased neutron-detection efficiency. One embodiment of the detectors utilizes a semiconductor wafer with a matrix of spaced cavities filled with one or more types of neutron reactive material such as ¹⁰B or ⁶LiF. The cavities are etched into both the front and back surfaces of the device such that the cavities from one side surround the cavities from the other side. The cavities may be etched via holes or etched slots or trenches. In another embodiment, the cavities are different-sized and the smaller cavities extend into the wafer from the lower surfaces of the larger cavities. In a third embodiment, multiple layers of different neutron-responsive material are formed on one or more sides of the wafer. The new devices operate at room temperature, are compact, rugged, and reliable in design.

Analysis of the electron-beam-induced current of a polycrystalline p-n junction when the diffusion lengths of the material on either side of a grain boundary differ

NASA Technical Reports Server (NTRS)

Von Roos, O.; Luke, K. L.

1984-01-01

The short circuit current generated by the electron beam of a scanning electron microscope in p-n junctions is reduced by enhanced recombination at grain boundaries in polycrystalline material. Frequently, grain boundaries separate the semiconductor into regions possessing different minority carrier life times. This markedly affects the short circuit current I(sc) as a function of scanning distance from the grain boundary. It will be shown theoretically that (1) the minimum of the I(sc) in crossing the grain boundary with the scanning electron beam is shifted away from the grain boundary toward the region with smaller life time (shorter diffusion length), (2) the magnitude of the minimum differs markedly from those calculated under the assumption of equal diffusion lengths on either side of the grain boundary, and (3) the minimum disappears altogether for small surface recombination velocities (s less than 10,000 cm/s). These effects become negligible, however, for large recombination velocities s at grain boundaries. For p-type silicon this happens for s not less than 100,000 cm/s.

Effects of heat/citric acid reprocessing on high-flux polysulfone dialyzers.

PubMed

Cornelius, Rena M; McClung, W Glenn; Richardson, Robert M A; Estridge, Charles; Plaskos, Nicholas; Yip, Christopher M; Brash, John L

2002-01-01

The surface features, morphology, and tensile properties of fibers obtained from pristine, reprocessed, and reused Fresenius Polysulfone High-Flux (Hemoflow F80A) hemodialyzers have been studied. Scanning electron microscopy of the dialyzer fibers revealed a dense skin layer on the inner surface of the membrane and a relatively thick porous layer on the outer surface. Transmission electron microscopy and atomic force microscopy showed an alteration in membrane morphology due to reprocessing and reuse, or to a deposition of blood-borne material on the membrane that is not removed with reprocessing. Fluorescent microscopy images also showed that a fluorescent material not removed by heat/citric acid reprocessing builds up with continued use of the dialyzers. The tensile properties of the dialyzer fibers were not affected by the heat/citric acid reprocessing procedure. The protein layers formed on pristine and reused hemodialyzer membranes during clinical use were also studied using sodium dodecyl sulfate polyacrylamide gel electrophoresis and immunoblotting. A considerable amount of protein was found on the blood side of single and multiple use dialyzers. Proteins adsorbed on the dialysate side of the membrane were predominantly in the molecular weight region below 30 kDa. Little protein was detected on the membranes of reprocessed hemodialyzers.

Quantitative Profiling of Feruloylated Arabinoxylan Side-Chains from Graminaceous Cell Walls

PubMed Central

Schendel, Rachel R.; Meyer, Marleen R.; Bunzel, Mirko

2016-01-01

Graminaceous arabinoxylans are distinguished by decoration with feruloylated monosaccharidic and oligosaccharidic side-chains. Although it is hypothesized that structural complexity and abundance of these feruloylated arabinoxylan side-chains may contribute, among other factors, to resistance of plant cell walls to enzymatic degradation, quantitative profiling approaches for these structural units in plant cell wall materials have not been described yet. Here we report the development and application of a rapid and robust method enabling the quantitative comparison of feruloylated side-chain profiles in cell wall materials following mildly acidic hydrolysis, C18-solid phase extraction (SPE), reduction under aprotic conditions, and liquid chromatography with diode-array detection/mass spectrometry (LC-DAD/MS) separation and detection. The method was applied to the insoluble fiber/cell wall materials isolated from 12 whole grains: wild rice (Zizania aquatica L.), long-grain brown rice (Oryza sativa L.), rye (Secale cereale L.), kamut (Triticum turanicum Jakubz.), wheat (Triticum aestivum L.), spelt (Triticum spelta L.), intermediate wheatgrass (Thinopyrum intermedium), maize (Zea mays L.), popcorn (Zea mays L. var. everta), oat (Avena sativa L.) (dehulled), barley (Hordeum vulgare L.) (dehulled), and proso millet (Panicum miliaceum L.). Between 51 and 96% of the total esterified monomeric ferulates were represented in the quantified compounds captured in the feruloylated side-chain profiles, which confirms the significance of these structures to the global arabinoxylan structure in terms of quantity. The method provided new structural insights into cereal grain arabinoxylans, in particular, that the structural moiety α-l-galactopyranosyl-(1→2)-β-d-xylopyranosyl-(1→2)-5-O-trans-feruloyl-l-arabinofuranose (FAXG), which had previously only been described in maize, is ubiquitous to cereal grains. PMID:26834763

Parental Expectation of Side Effects Following Vaccination Is Self-fulfilling: A Prospective Cohort Study.

PubMed

Smith, Louise E; Weinman, John; Amlôt, Richard; Yiend, Jenny; Rubin, G James

2018-06-02

One of the major factors contributing to parental refusal of vaccinations is the perception that vaccines cause side effects. Although symptoms are commonly reported following vaccinations, their causes are not always straightforward. Although some may be directly attributable to the vaccine itself, others may reflect pre-existing or coincidental symptoms that are misattributed to the vaccine. To investigate psychological factors associated with parental report of side effects following vaccination with the child influenza vaccine, and parental intention to re-vaccinate one's child the following year. A prospective cohort study was run in primary care practices in London in the 2016-2017 influenza season (ClinicalTrials.gov number NCT02909855). Two hundred seventy parents from 14 practices completed a questionnaire before their child's vaccination. Follow-up questionnaires were completed 3 days after vaccination and one month after vaccination. Parental report of side effects and vaccination intention for the subsequent year were measured. Parental report of side effects was strongly associated with pre-vaccination expectation of side effects. Suggestions received from the media, National Health Service (NHS) vaccination leaflet, and health care workers, as well as uncertainty-related beliefs, perceived sensitivity of the child to medicines, pessimism, and anxiety were also associated with reporting side effects. Side effect report was associated with lower vaccination intention for the following influenza season. Side effect perception following vaccination is influenced by psychological factors, in particular expectations. Perceiving side effects reduces future vaccination intention. Future public health communications should aim to decrease unrealistic expectations of side effects to increase vaccine uptake.

Pharmacogenomic and clinical data link non-pharmacokinetic metabolic dysregulation to drug side effect pathogenesis

PubMed Central

Zielinski, Daniel C.; Filipp, Fabian V.; Bordbar, Aarash; Jensen, Kasper; Smith, Jeffrey W.; Herrgard, Markus J.; Mo, Monica L.; Palsson, Bernhard O.

2015-01-01

Drug side effects cause a significant clinical and economic burden. However, mechanisms of drug action underlying side effect pathogenesis remain largely unknown. Here, we integrate pharmacogenomic and clinical data with a human metabolic network and find that non-pharmacokinetic metabolic pathways dysregulated by drugs are linked to the development of side effects. We show such dysregulated metabolic pathways contain genes with sequence variants affecting side effect incidence, play established roles in pathophysiology, have significantly altered activity in corresponding diseases, are susceptible to metabolic inhibitors and are effective targets for therapeutic nutrient supplementation. Our results indicate that metabolic dysregulation represents a common mechanism underlying side effect pathogenesis that is distinct from the role of metabolism in drug clearance. We suggest that elucidating the relationships between the cellular response to drugs, genetic variation of patients and cell metabolism may help managing side effects by personalizing drug prescriptions and nutritional intervention strategies. PMID:26055627

PCV Solid Rocket Motor: Design Status of the Motor Case Structure

NASA Astrophysics Data System (ADS)

Mataloni, A.; Zallo, A.; Perugini, P.; Di Cosmo, A.; Pasquale, N.; Mucci, R.

2014-06-01

For the VEGA Launch system new developments are running in order to allow: a) performances increase b) cost reduction c) introduction of new technologies.In the VEGA C configuration the PCV SRM replace the P80 in the first stage.The PCV design is based on the consolidate AVIO heritage with important improvements both from the material and from the technological side.Important improvements in skirts manufacturing will be tested as well, with the development of a customized automatic tape laying machine.From the material side a top class fiber will be selected on the bases of extensive trade-off plan which is under completion.The pre-preg material is based on an in-house resin formulation tailored to the specific motor case process requirements.

Occupant kinematics and estimated effectiveness of side airbags in pole side impacts using a human FE model with internal organs.

PubMed

Hayashi, Shigeki; Yasuki, Tsuyoshi; Kitagawa, Yuichi

2008-11-01

When a car collides against a pole-like obstacle, the deformation pattern of the vehicle body-side tends to extend to its upper region. A possible consequence is an increase of loading to the occupant thorax. Many studies have been conducted to understand human thoracic responses to lateral loading, and injury criteria have been developed based on the results. However, injury mechanisms, especially those of internal organs, are not well understood. A human body FE model was used in this study to simulate occupant kinematics in a pole side impact. Internal organ parts were introduced into the torso model, including their geometric features, material properties and connections with other tissues. The mechanical responses of the model were validated against PMHS data in the literature. Although injury criterion for each organ has not been established, pressure level and its changes can be estimated from the organ models. Finite element simulations were conducted assuming a case where a passenger vehicle collides against a pole at 29km/h. Occupant kinematics, force-deformation responses and pressure levels were compared between cases with and without side airbag deployment. The results indicated that strain to the ribs and pressure to the organs was smaller with side airbag deployment. The side airbag widened the contact area at the torso, helping to distribute the force to the shoulder, arm and chest. Such distributed force helped generate relatively smaller deformation in the ribs. Furthermore, the side airbag deployment helped restrict the spine displacement. The smaller displacement contributed to lowering the magnitude of contact force between the torso and the door. The study also examined the correlations between the pressure levels in the internal organs, rib deflection, and V*C of chest. The study found that the V*C(t) peak appeared to be synchronized with the organ pressure peak, suggesting that the pressure level of the internal organs could be one possible indicator to estimate their injury risk.

High-temperature molten salt thermal energy storage systems for solar applications

NASA Technical Reports Server (NTRS)

Petri, R. J.; Claar, T. D.; Ong, E.

1983-01-01

Experimental results of compatibility screening studies of 100 salt/containment/thermal conductivity enhancement (TCE) combinations for the high temperature solar thermal application range of 704 deg to 871 C (1300 to 1600 F) are presented. Nine candidate containment/HX alloy materials and two TCE materials were tested with six candidate solar thermal alkali and alkaline earth carbonate storage salts (both reagent and technical grade of each). Compatibility tests were conducted with salt encapsulated in approx. 6.0 inch x 1 inch welded containers of test material from 300 to 3000 hours. Compatibility evaluations were end application oriented, considering the potential 30 year lifetime requirement of solar thermal power plant components. Analyses were based on depth and nature of salt side corrosion of materials, containment alloy thermal aging effects, weld integrity in salt environment, air side containment oxidation, and chemical and physical analyses of the salt. A need for more reliable, and in some cases first time determined thermophysical and transport property data was also identified for molten carbonates in the 704 to 871 C temperature range. In particular, accurate melting point (mp) measurements were performed for Li2CO3 and Na2CO3 while melting point, heat of fusion, and specific heat determinations were conducted on 81.3 weight percent Na2CO3-18.7 weight percent K2CO3 and 52.2 weight percent BaCO3-47.8 weight percent Na2CO3 to support future TES system design and ultimate scale up of solar thermal energy storage (TES) subsystems.

Radiation Therapy Side Effects

Cancer.gov

Radiation therapy has side effects because it not only kills or slows the growth of cancer cells, it can also affect nearby healthy cells. Many people who get radiation therapy experience fatigue. Other side effects depend on the part of the body that is being treated. Learn more about possible side effects.

Influence of opioid-related side effects on disability, mood, and opioid misuse risk among patients with chronic pain in primary care.

PubMed

Jamison, Robert N; Dorado, Kathleen; Mei, Anna; Edwards, Robert R; Martel, Marc O

2017-03-01

There is increasing concern among primary care practitioners about the use of opioids for chronic pain, including their adverse effects, but little attention has been given to how reports of side effects from prescription medication can contribute to outcomes among patients with chronic pain. The aim of this study was to investigate the impact of frequently reported side effects on mood, disability, and opioid misuse in patients with chronic pain prescribed opioids within primary care. Two hundred (N = 200) patients with chronic pain taking opioids for pain were recruited into the study. All patients completed baseline measures and a monthly side effects checklist once a month for 6 months. Patients were divided evenly based on a median split of the number of endorsed side effects over 6 months. The subjects repeated the baseline measures at the end of the study period. Over time, reports of medication side effects tended to decrease, but differences in frequency of reported side effects from baseline to follow-up (6-month time) were not significant, and the order of the frequency of the reported side effects remained similar. Patients who reported significant medication-related adverse effects reported significantly greater activity interference, negative affect, and catastrophizing compared with those with fewer side effects ( P < 0.01). In addition, those patients with pain who reported more side effects showed significantly higher scores on opioid misuse risk ( P < 0.001). This study demonstrates the important role of monitoring medication-related side effects among patients with chronic pain who are prescribed opioid medication for pain within primary care.

Influence of opioid-related side effects on disability, mood, and opioid misuse risk among patients with chronic pain in primary care

PubMed Central

Jamison, Robert N.; Dorado, Kathleen; Mei, Anna; Edwards, Robert R.; Martel, Marc O.

2017-01-01

Abstract Background: There is increasing concern among primary care practitioners about the use of opioids for chronic pain, including their adverse effects, but little attention has been given to how reports of side effects from prescription medication can contribute to outcomes among patients with chronic pain. The aim of this study was to investigate the impact of frequently reported side effects on mood, disability, and opioid misuse in patients with chronic pain prescribed opioids within primary care. Methods: Two hundred (N = 200) patients with chronic pain taking opioids for pain were recruited into the study. All patients completed baseline measures and a monthly side effects checklist once a month for 6 months. Patients were divided evenly based on a median split of the number of endorsed side effects over 6 months. The subjects repeated the baseline measures at the end of the study period. Results: Over time, reports of medication side effects tended to decrease, but differences in frequency of reported side effects from baseline to follow-up (6-month time) were not significant, and the order of the frequency of the reported side effects remained similar. Patients who reported significant medication-related adverse effects reported significantly greater activity interference, negative affect, and catastrophizing compared with those with fewer side effects (P < 0.01). In addition, those patients with pain who reported more side effects showed significantly higher scores on opioid misuse risk (P < 0.001). Discussion: This study demonstrates the important role of monitoring medication-related side effects among patients with chronic pain who are prescribed opioid medication for pain within primary care. PMID:29392205

Side effects of low-dose pyridostigmine bromide are not related to cholinesterase inhibition.

PubMed

Cook, M R; Gerkovich, M M; Sastre, A; Graham, C

2001-12-01

Pretreatment with pyridostigmine bromide (PB) has become part of standard military procedures for protection against the effects of possible chemical warfare attack. The purpose of the work reported here was to quantify the type, intensity and frequency of side effects of low-dose PB, and to examine factors that predict the intensity and frequency of side effects. A double-blind, cross-over, placebo (PL)-controlled design was used. Of the 67 subjects, 33 received 30 mg PB every 8 h for 13 doses, and 34 received 60 mg on the same schedule. Order of PB and PL administration was counterbalanced. Overall, side effects were mild, even at the 60-mg dose level. More side effects were reported when volunteers were taking PB than when they were taking placebo. Women reported more symptoms than men. Neither cholinesterase inhibition nor plasma levels of PB predicted side effect scores during the PB week; the best predictor of side effect scores during the PB week was side effect scores during the PL week. PB is well tolerated by healthy young people, even when twice the recommended military dose is administered.

Comparison the effectiveness of pyruvic acid 50% and salicylic acid 30% in the treatment of acne

PubMed Central

Jaffary, Fariba; Faghihi, Gita; Saraeian, Sara; Hosseini, Sayed Mohsen

2016-01-01

Background: Acne vulgaris is a chronic inflammatory disease of the pilosebaceous follicles and one of the most common skin diseases. The peeling method has been recently found to be effective for acne treatment. This study aimed to compare the efficacy of pyruvic acid 50% and salicylic acid 30% peeling in the treatment of mild to moderate acne. Materials and Methods: In a prospective single-blinded clinical trial, 86 patients with acne were randomly assigned into two groups. In both groups, the routine treatment of acne (topical solution of erythromycin 4%, triclorocarban soap, and sunscreen) were used twice a day for 8 weeks. In addition, salicylic acid 30% for the control group and pyruvic acid 50% for the case group were used. In both groups, acne severity index (ASI) was calculated before and at week 2, 4, 6, and 8 of the treatment. Patient satisfaction was assessed at the end of the treatment. Side effects were recorded using a checklist. Results: In both groups, the reduction in the number of comedones, papules, and ASI were statistically significant (P < 0.001) in the course of treatment. However, it was not significant regarding the number of pustules (P = 0.09). None of the number of comedone, papules, pustules, and ASI was statistically different between study groups. Both treatment groups had similar side effects except for scaling in the fifth session, which was significantly lower in salicylic acid – treated patients (P = 0.015). Conclusion: Both pyruvic acid 50% and salicylic acid 30% are effective in the improvement of mild to moderate acne with no significant difference in efficacy and side effects. PMID:27904577

Factors affecting patient's perception of anticancer treatments side-effects: an observational study.

PubMed

Russo, Stefania; Cinausero, Marika; Gerratana, Lorenzo; Bozza, Claudia; Iacono, Donatella; Driol, Pamela; Deroma, Laura; Sottile, Roberta; Fasola, Gianpiero; Puglisi, Fabio

2014-02-01

Analysis of relative importance of side effects of anticancer therapy is extremely useful in the process of clinical decision making. There is evidence that patients' perception of the side effects of anticancer treatments changes over time. Aim of this study was to evaluate the cancer patients' perceptions of physical and non-physical side effects of contemporary anticancer therapy. Four hundred and sixty-four patients entered the study (153 men and 311 women). Participants were asked to rank their side effects in order of distress by using two sets of cards naming physical and non-physical effects, respectively. Influencing factors, including treatment and patient characteristics, were also analysed. Patients ranked the non-physical side effect 'Affects my family or partner' first. 'Constantly tired' and 'Loss of hair' were ranked second and third, respectively. Significant differences from previous studies on this topic emerged. In particular, 'Vomiting', a predominant concern in previous studies, almost disappeared, whereas 'Nausea' and 'Loss of hair' remained important side effects in the patients' perception. Interestingly, marital status was predominant in driving patients' perception, being associated with several side effects ('Constantly tired', 'Loss of appetite', 'Affects my work/Home duties', 'Affects my social activities', 'Infertility'). Other significant factors influencing patient's perception of side effects included age, disease characteristics and ongoing anticancer therapy. This study provided information on current status of patients' perceptions of side effects of anticancer treatment. These results could be used in pre-treatment patient education and counselling.

Perceived risk of tamoxifen side effects: a study of the use of absolute frequencies or frequency bands, with or without verbal descriptors.

PubMed

Knapp, Peter; Gardner, Peter H; Raynor, David K; Woolf, Elizabeth; McMillan, Brian

2010-05-01

To investigate the effectiveness of presenting medicine side effect risk information in different forms, including that proposed by UK guidelines [[1] Medicines and Healthcare products Regulatory Agency. Always read the leaflet-Getting the best information with every medicine. (Report of the Committee on Safety of Medicines Working Group on Patient Information). London: The Stationery Office, 2005.]. 134 Cancer Research UK (CRUK) website users were recruited via a 'pop-up'. Using a 2x2 factorial design, participants were randomly allocated to one of four conditions and asked to: imagine they had to take tamoxifen, estimate the risks of 4 side effects, and indicate a presentation mode preference. Those presented with absolute frequencies demonstrated greater accuracy in estimating 2 of 4 side effects, and of any side effect occurring, than those presented with frequency bands. Those presented with combined descriptors were more accurate at estimating the risk of pulmonary embolism than those presented with numeric descriptors only. Absolute frequencies outperform frequency bands when presenting side effect risk information. However, presenting such exact frequencies for every side effect may be much less digestible than all side effects listed under 5 frequency bands. Combined numerical and verbal descriptors may be better than numeric only descriptors when describing infrequent side effects. Information about side effects should be presented in ways that patients prefer, and which result in most accurate risk estimates. Copyright (c) 2009 Elsevier Ireland Ltd. All rights reserved.

Back-side readout semiconductor photomultiplier

DOEpatents

Choong, Woon-Seng; Holland, Stephen E

2014-05-20

This disclosure provides systems, methods, and apparatus related to semiconductor photomultipliers. In one aspect, a device includes a p-type semiconductor substrate, the p-type semiconductor substrate having a first side and a second side, the first side of the p-type semiconductor substrate defining a recess, and the second side of the p-type semiconductor substrate being doped with n-type ions. A conductive material is disposed in the recess. A p-type epitaxial layer is disposed on the second side of the p-type semiconductor substrate. The p-type epitaxial layer includes a first region proximate the p-type semiconductor substrate, the first region being implanted with p-type ions at a higher doping level than the p-type epitaxial layer, and a second region disposed on the first region, the second region being doped with p-type ions at a higher doping level than the first region.

Turbine airfoil with controlled area cooling arrangement

DOEpatents

Liang, George

2010-04-27

A gas turbine airfoil (10) includes a serpentine cooling path (32) with a plurality of channels (34,42,44) fluidly interconnected by a plurality of turns (38,40) for cooling the airfoil wall material. A splitter component (50) is positioned within at least one of the channels to bifurcate the channel into a pressure-side channel (46) passing in between the outer wall (28) and the inner wall (30) of the pressure side (24) and a suction-side channel (48) passing in between the outer wall (28) and the inner wall (30) of the suction side (26) longitudinally downstream of an intermediate height (52). The cross-sectional area of the pressure-side channel (46) and suction-side channel (48) are thereby controlled in spite of an increasing cross-sectional area of the airfoil along its longitudinal length, ensuring a sufficiently high mach number to provide a desired degree of cooling throughout the entire length of the airfoil.

Space ultra-vacuum facility and method of operation

NASA Technical Reports Server (NTRS)

Naumann, Robert J. (Inventor)

1988-01-01

A wake shield space processing facility (10) for maintaining ultra-high levels of vacuum is described. The wake shield (12) is a truncated hemispherical section having a convex side (14) and a concave side (24). Material samples (68) to be processed are located on the convex side of the shield, which faces in the wake direction in operation in orbit. Necessary processing fixtures (20) and (22) are also located on the convex side. Support equipment including power supplies (40, 42), CMG package (46) and electronic control package (44) are located on the convex side (24) of the shield facing the ram direction. Prior to operation in orbit the wake shield is oriented in reverse with the convex side facing the ram direction to provide cleaning by exposure to ambient atomic oxygen. The shield is then baked-out by being pointed directed at the sun to obtain heating for a suitable period.

Do Student Learning Styles Translate to Different "Testing Styles"?

ERIC Educational Resources Information Center

Leithner, Anika

2011-01-01

Professors seem to be more aware of different student learning styles than ever before and are utilizing various teaching techniques in order to appeal to different students in their classes. Unfortunately, presenting materials is only one side of the coin, while the other side--assessment--has not received the same amount of attention. After all,…

MTR WING A, TRA604. SOUTH SIDE. CAMERA FACING NORTH. THIS ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

MTR WING A, TRA-604. SOUTH SIDE. CAMERA FACING NORTH. THIS VIEW TYPIFIES TENDENCY FOR EXPANSIONS TO TAKE THE FORM OF PROJECTIONS AND INFILL USING AVAILABLE YARD SPACES. INL NEGATIVE NO. HD47-44-3. Mike Crane, Photographer, 4/2005 - Idaho National Engineering Laboratory, Test Reactor Area, Materials & Engineering Test Reactors, Scoville, Butte County, ID

24 CFR 200.926 - Minimum property standards for one and two family dwellings.

Code of Federal Regulations, 2011 CFR

2011-04-01

... units in a structure where the units are located side-by-side in town house fashion. Section 200.926d(c... the subarea for seismic design (see § 200.926a(c)(5)), or if it fails to regulate subareas in more..., structural loads and seismic design, foundation systems, materials standards, construction components, glass...

24 CFR 200.926 - Minimum property standards for one and two family dwellings.

Code of Federal Regulations, 2010 CFR

2010-04-01

... units in a structure where the units are located side-by-side in town house fashion. Section 200.926d(c... the subarea for seismic design (see § 200.926a(c)(5)), or if it fails to regulate subareas in more..., structural loads and seismic design, foundation systems, materials standards, construction components, glass...

Side-chain Liquid Crystal Polymers (SCLCP): Methods and Materials. An Overview

PubMed Central

Ganicz, Tomasz; Stańczyk, Włodzimierz

2009-01-01

This review focuses on recent developments in the chemistry of side chain liquid crystal polymers. It concentrates on current trends in synthetic methods and novel, well defined structures, supramolecular arrangements, properties, and applications. The review covers literature published in this century, apart from some areas, such as dendritic and elastomeric systems, which have been recently reviewed.