Magnetic and Structural Characterization of Fe-Ga Using Kerr Microscopy and Neutron Scattering

DTIC Science & Technology

2010-01-01

117 4.6 Schematic of triple axes single crystal neutron diffractometer (left). TriCS intrument at Paul Scherrer Institut, Switzerland (right...Therefore, USANS data is one-dimensional. 4.3.3 Single Crystal Neutron Diffraction The single crystal neutron diffractometer, TriCS at Paul Scherrer...crystal neutron diffractometer (left). TriCS intrument at Paul Scherrer Institut, Switzerland (right) [106] 4.4 Unpolarized SANS In this section, SANS

76 FR 59167 - Siemens Medical Solutions USA, Inc., Oncology Care Systems Division, Concord, CA; Siemens Medical...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-23

... Medical Solutions USA, Inc., Oncology Care Systems Division, Concord, CA; Siemens Medical Solutions USA... Solutions USA, Inc. (Siemens), Oncology Care Systems Division, Concord, California (subject firm). The...., Oncology Care Systems Division, Concord, California (TA-W-73,158) and Siemens Medical Solutions USA, Inc...

Building Energy Management Open Source Software

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rahman, Saifur

Funded by the U.S. Department of Energy in November 2013, a Building Energy Management Open Source Software (BEMOSS) platform was engineered to improve sensing and control of equipment in small- and medium-sized commercial buildings. According to the Energy Information Administration (EIA), small- (5,000 square feet or smaller) and medium-sized (between 5,001 to 50,000 square feet) commercial buildings constitute about 95% of all commercial buildings in the U.S. These buildings typically do not have Building Automation Systems (BAS) to monitor and control building operation. While commercial BAS solutions exist, including those from Siemens, Honeywell, Johnsons Controls and many more, they aremore » not cost effective in the context of small- and medium-sized commercial buildings, and typically work with specific controller products from the same company. BEMOSS targets small and medium-sized commercial buildings to address this gap.« less

Quantitative comparison of noise texture across CT scanners from different manufacturers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Solomon, Justin B.; Christianson, Olav; Samei, Ehsan

2012-10-15

Purpose: To quantitatively compare noise texture across computed tomography (CT) scanners from different manufacturers using the noise power spectrum (NPS). Methods: The American College of Radiology CT accreditation phantom (Gammex 464, Gammex, Inc., Middleton, WI) was imaged on two scanners: Discovery CT 750HD (GE Healthcare, Waukesha, WI), and SOMATOM Definition Flash (Siemens Healthcare, Germany), using a consistent acquisition protocol (120 kVp, 0.625/0.6 mm slice thickness, 250 mAs, and 22 cm field of view). Images were reconstructed using filtered backprojection and a wide selection of reconstruction kernels. For each image set, the 2D NPS were estimated from the uniform section ofmore » the phantom. The 2D spectra were normalized by their integral value, radially averaged, and filtered by the human visual response function. A systematic kernel-by-kernel comparison across manufacturers was performed by computing the root mean square difference (RMSD) and the peak frequency difference (PFD) between the NPS from different kernels. GE and Siemens kernels were compared and kernel pairs that minimized the RMSD and |PFD| were identified. Results: The RMSD (|PFD|) values between the NPS of GE and Siemens kernels varied from 0.01 mm{sup 2} (0.002 mm{sup -1}) to 0.29 mm{sup 2} (0.74 mm{sup -1}). The GE kernels 'Soft,''Standard,''Chest,' and 'Lung' closely matched the Siemens kernels 'B35f,''B43f,''B41f,' and 'B80f' (RMSD < 0.05 mm{sup 2}, |PFD| < 0.02 mm{sup -1}, respectively). The GE 'Bone,''Bone+,' and 'Edge' kernels all matched most closely with Siemens 'B75f' kernel but with sizeable RMSD and |PFD| values up to 0.18 mm{sup 2} and 0.41 mm{sup -1}, respectively. These sizeable RMSD and |PFD| values corresponded to visually perceivable differences in the noise texture of the images. Conclusions: It is possible to use the NPS to quantitatively compare noise texture across CT systems. The degree to which similar texture across scanners could be achieved varies and is limited by the kernels available on each scanner.« less

Quantitative comparison of noise texture across CT scanners from different manufacturers.

PubMed

Solomon, Justin B; Christianson, Olav; Samei, Ehsan

2012-10-01

To quantitatively compare noise texture across computed tomography (CT) scanners from different manufacturers using the noise power spectrum (NPS). The American College of Radiology CT accreditation phantom (Gammex 464, Gammex, Inc., Middleton, WI) was imaged on two scanners: Discovery CT 750HD (GE Healthcare, Waukesha, WI), and SOMATOM Definition Flash (Siemens Healthcare, Germany), using a consistent acquisition protocol (120 kVp, 0.625∕0.6 mm slice thickness, 250 mAs, and 22 cm field of view). Images were reconstructed using filtered backprojection and a wide selection of reconstruction kernels. For each image set, the 2D NPS were estimated from the uniform section of the phantom. The 2D spectra were normalized by their integral value, radially averaged, and filtered by the human visual response function. A systematic kernel-by-kernel comparison across manufacturers was performed by computing the root mean square difference (RMSD) and the peak frequency difference (PFD) between the NPS from different kernels. GE and Siemens kernels were compared and kernel pairs that minimized the RMSD and |PFD| were identified. The RMSD (|PFD|) values between the NPS of GE and Siemens kernels varied from 0.01 mm(2) (0.002 mm(-1)) to 0.29 mm(2) (0.74 mm(-1)). The GE kernels "Soft," "Standard," "Chest," and "Lung" closely matched the Siemens kernels "B35f," "B43f," "B41f," and "B80f" (RMSD < 0.05 mm(2), |PFD| < 0.02 mm(-1), respectively). The GE "Bone," "Bone+," and "Edge" kernels all matched most closely with Siemens "B75f" kernel but with sizeable RMSD and |PFD| values up to 0.18 mm(2) and 0.41 mm(-1), respectively. These sizeable RMSD and |PFD| values corresponded to visually perceivable differences in the noise texture of the images. It is possible to use the NPS to quantitatively compare noise texture across CT systems. The degree to which similar texture across scanners could be achieved varies and is limited by the kernels available on each scanner.

Genotoxicity tests on D-tagatose.

PubMed

Kruger, C L; Whittaker, M H; Frankos, V H

1999-04-01

D-tagatose is a low-calorie sweetener that tastes like sucrose. Its genotoxic potential was examined in five standard assays: the Ames Salmonella typhimurium reverse mutation assay, the Escherichia coli/mammalian microsome assay, a chromosomal aberration assay in Chinese hamster ovary cells, a mouse lymphoma forward mutation assay, and an in vivo mouse micronucleus assay. D-tagatose was not found to increase the number of revertants per plate relative to vehicle controls in either the S. typhimurium tester strains or the WP2uvrA- tester strain with or without metabolic activation at doses up to 5000 microg/plate. No significant increase in Chinese hamster ovary cells with chromosomal aberrations was observed at concentrations up to 5000 microg/ml with or without metabolic activation. D-tagatose was not found to increase the mutant frequency in mouse lymphoma L5178Y cells with or without metabolic activation up to concentrations of 5000 microg/ml. D-tagatose caused no significant increase in micronuclei in bone marrow polychromatic erythrocytes at doses up to 5000 mg/kg. D-tagatose was not found to be genotoxic under the conditions of any of the assays described above. Copyright 1999 Academic Press.

Interpretation of normal anatomic structures on chest radiography: Comparison of Fuji Computed Radiography (FCR) 5501D with FCR 5000 and screen‐film system

PubMed Central

Nakashima, Kazuaki; Ashizawa, Kazuto; Ochi, Makoto; Hashmi, Rashid; Hayashi, Kuniaki; Gotoh, Shinichi; Honda, Sumihisa; Igarashi, Akito; Komaki, Takao

2003-01-01

The purpose of this study was to investigate the usefulness of Fuji Computed Radiography (FCR) 5501D by comparing it with FCR 5000 and a screen‐film system (S/F). Posteroanterior chest radiographs often patients with no abnormality on chest CT scans were obtained with FCR 5501D, FCR 5000, and S/F. Six observers (three radiologists and three radio‐technologists) evaluated the visibility of nine normal anatomic structures (including lungs, soft tissue, and bones) and overall visibility on each image. Observers scored using a five‐point scale on each structure. FCR 5000 showed a significantly higher score in soft tissue and bone structures, and overall visibility compared with S/F, but, there was no significant difference between them in the visibility of all four normal lung structures. Compared with S/F, the score for FCR 5501D was higher in eight of the nine normal structures, including three of the four lung structures (unobscured lung, retrocardiac lung, and subdiaphragmatic lung), and overall visibility. Compared with FCR 5000, the score for FCR 5501D was higher in three normal structures, including two of the four lung structures (unobscured lung and subdiaphragmatic lung), and overall visibility. FCR 5501D was the best among the three techniques to visualize normal anatomic structures, particularly the obscured and unobscured lung. © 2003 American College of Medical Physics. PACS number(s): 87.57.–s, 87.62.+n PMID:12540822

The Macromolecular Neutron Diffractometer MaNDi at the Spallation Neutron Source

DOE PAGES

Coates, Leighton; Cuneo, Matthew J.; Frost, Matthew J.; ...

2015-07-18

The Macromolecular Neutron Diffractometer (MaNDi) is located on beamline 11B of the Spallation Neutron Source at Oak Ridge National Laboratory. Moreover, the instrument is a neutron time-of-flight wavelength-resolved Laue diffractometer optimized to collect diffraction data from single crystals. Finally, the instrument has been designed to provide flexibility in several instrumental parameters, such as beam divergence and wavelength bandwidth, to allow data collection from a range of macromolecular systems.

The neutron texture diffractometer at the China Advanced Research Reactor

NASA Astrophysics Data System (ADS)

Li, Mei-Juan; Liu, Xiao-Long; Liu, Yun-Tao; Tian, Geng-Fang; Gao, Jian-Bo; Yu, Zhou-Xiang; Li, Yu-Qing; Wu, Li-Qi; Yang, Lin-Feng; Sun, Kai; Wang, Hong-Li; Santisteban, J. r.; Chen, Dong-Feng

2016-03-01

The first neutron texture diffractometer in China has been built at the China Advanced Research Reactor, due to strong demand for texture measurement with neutrons from the domestic user community. This neutron texture diffractometer has high neutron intensity, moderate resolution and is mainly applied to study texture in commonly used industrial materials and engineering components. In this paper, the design and characteristics of this instrument are described. The results for calibration with neutrons and quantitative texture analysis of zirconium alloy plate are presented. The comparison of texture measurements with the results obtained in HIPPO at LANSCE and Kowari at ANSTO illustrates the reliability of the texture diffractometer. Supported by National Nature Science Foundation of China (11105231, 11205248, 51327902) and International Atomic Energy Agency-TC program (CPR0012)

Deposition, Alteration, and Resuspension of Colorado River Delta Sediments, Lake Powell, Utah

NASA Astrophysics Data System (ADS)

Kramer, N. M.; Parnell, R.

2002-12-01

Current drought conditions in the southwest United States have resulted in lowering water levels in Lake Powell, Utah. Delta sediments forming at the Colorado River inflow for the past 39 years are becoming exposed and reworked as lake levels continue to fall to over 22 meters below full pool level. Fine sediments act as a sink for pollutants by adsorbing contaminants to their surfaces. Reworking these sediments may pose a risk to water quality in the lake. We examine whether burial and time have sufficiently altered fine sediments in the delta and affected materials adsorbed on their surfaces. Fifteen lake cores and six sediment traps were collected from the sediment delta forming at the Colorado River inflow in Lake Powell. This research characterizes fine sediment mineralogy, the composition of exchangeable materials, and organic matter content within delta sediments to determine the type and amount of alteration of these sediments with cycles of burial and resuspension. We hypothesize that as sediments are reworked, organic carbon is degraded and organic nitrogen is released forming ammonium in these reducing conditions. Sediment trap samples will be used to test this hypothesis. Trap samples will be compared to subsamples from sediment cores to determine the amount of alteration of fine sediments. All samples are analyzed for organic carbon, organic nitrogen, ammonium, cation exchange capacity, exchangeable cation composition, and clay mineralogy. Organic carbon and nitrogen are analyzed using a Leco CN analyzer. Ammonium is analyzed using a Lachet ion chromatograph. Clay mineralogy is characterized using a Siemens D500 powder X-ray diffractometer. Cation exchange capacity and exchangeable cations are measured using standard soil chemical techniques. Clay mineral analyses indicate significant spatial and temporal differences in fine sediment entering the Lake Powell delta which complicates the use of a simple deposition/alteration/resuspension model using a single starting material.

Methodology for cloud-based design of robots

NASA Astrophysics Data System (ADS)

Ogorodnikova, O. M.; Vaganov, K. A.; Putimtsev, I. D.

2017-09-01

This paper presents some important results for cloud-based designing a robot arm by a group of students. Methodology for the cloud-based design was developed and used to initiate interdisciplinary project about research and development of a specific manipulator. The whole project data files were hosted by Ural Federal University data center. The 3D (three-dimensional) model of the robot arm was created using Siemens PLM software (Product Lifecycle Management) and structured as a complex mechatronics product by means of Siemens Teamcenter thin client; all processes were performed in the clouds. The robot arm was designed in purpose to load blanks up to 1 kg into the work space of the milling machine for performing student's researches.

The Utilization of Requirement Statement Methodologies in the United States Navy and Their Impact on Systems Acquisition.

DTIC Science & Technology

1980-03-01

RESEARCH LABORATORY (N R L )-------52 C. NATAL AIR DEVELOPMENT CENTER (NADC) -------------. 52 D. FLEET COMBAT DIRECTION SYSTEMS SUPPORT CENTER...DEPARTMENT OF DEFENSE DIRECTIVES 5000.1 A3D 500.2-...................... 61 1. Technology Base-------- -aaaaaaaaaaa1 2. Competitive ip loration of...Alternative Solutions -- - - 62 C. DEPARTMENT OF DEFENSE DIRECTIVE 5000.29------ 64 6 D. DEPARTMENT OF DEFENSE INSTRUCTION 501 .21 65 I. MILITARY STANDARD 1679

78 FR 19017 - Manufacturer of Controlled Substances; Notice of Registration; Siemens Healthcare Diagnostics, Inc.

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-28

...; Notice of Registration; Siemens Healthcare Diagnostics, Inc. By Notice dated November 27, 2012, and published in the Federal Register on December 5, 2012, 77 FR 72409, Siemens Healthcare Diagnostics Inc... Siemens Healthcare Diagnostics Inc., to manufacture the listed basic classes of controlled substances is...

Validity of Treadmill-Derived Critical Speed on Predicting 5000-Meter Track-Running Performance.

PubMed

Nimmerichter, Alfred; Novak, Nina; Triska, Christoph; Prinz, Bernhard; Breese, Brynmor C

2017-03-01

Nimmerichter, A, Novak, N, Triska, C, Prinz, B, and Breese, BC. Validity of treadmill-derived critical speed on predicting 5,000-meter track-running performance. J Strength Cond Res 31(3): 706-714, 2017-To evaluate 3 models of critical speed (CS) for the prediction of 5,000-m running performance, 16 trained athletes completed an incremental test on a treadmill to determine maximal aerobic speed (MAS) and 3 randomly ordered runs to exhaustion at the [INCREMENT]70% intensity, at 110% and 98% of MAS. Critical speed and the distance covered above CS (D') were calculated using the hyperbolic speed-time (HYP), the linear distance-time (LIN), and the linear speed inverse-time model (INV). Five thousand meter performance was determined on a 400-m running track. Individual predictions of 5,000-m running time (t = [5,000-D']/CS) and speed (s = D'/t + CS) were calculated across the 3 models in addition to multiple regression analyses. Prediction accuracy was assessed with the standard error of estimate (SEE) from linear regression analysis and the mean difference expressed in units of measurement and coefficient of variation (%). Five thousand meter running performance (speed: 4.29 ± 0.39 m·s; time: 1,176 ± 117 seconds) was significantly better than the predictions from all 3 models (p < 0.0001). The mean difference was 65-105 seconds (5.7-9.4%) for time and -0.22 to -0.34 m·s (-5.0 to -7.5%) for speed. Predictions from multiple regression analyses with CS and D' as predictor variables were not significantly different from actual running performance (-1.0 to 1.1%). The SEE across all models and predictions was approximately 65 seconds or 0.20 m·s and is therefore considered as moderate. The results of this study have shown the importance of aerobic and anaerobic energy system contribution to predict 5,000-m running performance. Using estimates of CS and D' is valuable for predicting performance over race distances of 5,000 m.

The Wide Angle Neutron Diffractometer (WAND) at HFIR: possibilities and future

NASA Astrophysics Data System (ADS)

Frontzek, Matthias; Andrews, Katie M.; Chakoumakos, Bryan C.

The Wide Angle Neutron Diffractometer (WAND) at the High Flux Isotope Reactor (HFIR) at the Oak Ridge National Laboratory (ORNL) has been built and continues to be, a joint project between ORNL and the Japan Atomic Energy Agency. Equipped with a 1-dimensional position sensitive detector (PSD), the instrument is a multi-purpose instrument for both powder and single crystal diffraction. WAND is currently in the process of a 2-phase upgrade to become a world class, general purpose instrument. In phase 1, finished in the beginning of 2016, the whole instrument was practically re-built from scratch, keeping only the front end and the 1-D PSD. Phase 2 will replace the 1-D PSD with the state of the art BNL120 2D-PSD which comes from the Lujan Neutron Scattering Center. We are currently integrating the detector off-line into the data acquisition architecture at HFIR. The new instrument, WAND2, will be available for general users in the proposal call 2018A. In our contribution we present results from experiments on WAND after phase 1. The upgrade now allows mounting the whole suite of available sample environment (50 mK to 1500 K, magnetic fields (5 T), high pressures (4 GPa)). We will further discuss the scientific impact the new capabilities of WAND2 will have.

49 CFR Appendix A to Part 232 - Schedule of Civil Penalties 1

Code of Federal Regulations, 2013 CFR

2013-10-01

...) Failure to meet general design requirements 2,500 5,000 (d) Failure to have proper percentage of operative brakes from Class I brake test 5,000 7,500 (e) Operating with less than 85 percent operative brakes 5,000...) Failure to adopt and comply with periodic assessment plan 7,500 11,000 232.205Class I brake test—initial...

49 CFR Appendix A to Part 232 - Schedule of Civil Penalties 1

Code of Federal Regulations, 2012 CFR

2012-10-01

...) Failure to meet general design requirements 2,500 5,000 (d) Failure to have proper percentage of operative brakes from Class I brake test 5,000 7,500 (e) Operating with less than 85 percent operative brakes 5,000...) Failure to adopt and comply with periodic assessment plan 7,500 11,000 232.205Class I brake test—initial...

49 CFR Appendix A to Part 232 - Schedule of Civil Penalties 1

Code of Federal Regulations, 2010 CFR

2010-10-01

...) Failure to meet general design requirements 2,500 5,000 (d) Failure to have proper percentage of operative brakes from Class I brake test 5,000 7,500 (e) Operating with less than 85 percent operative brakes 5,000...) Failure to adopt and comply with periodic assessment plan 7,500 11,000 232.205Class I brake test—initial...

49 CFR Appendix A to Part 232 - Schedule of Civil Penalties 1

Code of Federal Regulations, 2014 CFR

2014-10-01

...) Failure to meet general design requirements 2,500 5,000 (d) Failure to have proper percentage of operative brakes from Class I brake test 5,000 7,500 (e) Operating with less than 85 percent operative brakes 5,000...) Failure to adopt and comply with periodic assessment plan 7,500 11,000 232.205Class I brake test—initial...

A novel X-ray diffractometer for studies of liquid-liquid interfaces.

PubMed

Murphy, Bridget M; Greve, Matthais; Runge, Benjamin; Koops, Christian T; Elsen, Annika; Stettner, Jochim; Seeck, Oliver H; Magnussen, Olaf M

2014-01-01

The study of liquid-liquid interfaces with X-ray scattering methods requires special instrumental considerations. A dedicated liquid surface diffractometer employing a tilting double-crystal monochromator in Bragg geometry has been designed. This diffractometer allows reflectivity and grazing-incidence scattering measurements of an immobile mechanically completely decoupled liquid sample, providing high mechanical stability. The available energy range is from 6.4 to 29.4 keV, covering many important absorption edges. The instrument provides access in momentum space out to 2.54 Å(-1) in the surface normal and out to 14.8 Å(-1) in the in-plane direction at 29.4 keV. Owing to its modular design the diffractometer is also suitable for heavy apparatus such as vacuum chambers. The instrument performance is described and examples of X-ray reflectivity studies performed under in situ electrochemical control and on biochemical model systems are given.

30 CFR Appendix I to Subpart D of... - Appendix I to Subpart D of Part 18

Code of Federal Regulations, 2012 CFR

2012-07-01

... LIST OF TABLES Table No. Title 1 Portable power cable ampacities—600 volts. 2 Portable cord ampacities—600 volts. 3 Portable power cable ampacities—601 to 5,000 volts. 4 Normal diameter of round cables... diameter of three-conductor portable power cables with tolerances in inches—601 to 5,000 volts. 8 Fuse...

30 CFR Appendix I to Subpart D of... - Appendix I to Subpart D of Part 18

Code of Federal Regulations, 2014 CFR

2014-07-01

... LIST OF TABLES Table No. Title 1 Portable power cable ampacities—600 volts. 2 Portable cord ampacities—600 volts. 3 Portable power cable ampacities—601 to 5,000 volts. 4 Normal diameter of round cables... diameter of three-conductor portable power cables with tolerances in inches—601 to 5,000 volts. 8 Fuse...

Sequence design and software environment for real-time navigation of a wireless ferromagnetic device using MRI system and single echo 3D tracking.

PubMed

Chanu, A; Aboussouan, E; Tamaz, S; Martel, S

2006-01-01

Software architecture for the navigation of a ferromagnetic untethered device in a 1D and 2D phantom environment is briefly described. Navigation is achieved using the real-time capabilities of a Siemens 1.5 T Avanto MRI system coupled with a dedicated software environment and a specially developed 3D tracking pulse sequence. Real-time control of the magnetic core is executed through the implementation of a simple PID controller. 1D and 2D experimental results are presented.

X-ray diffraction studies of shocked lunar analogs

NASA Technical Reports Server (NTRS)

Hanss, R. E.

1979-01-01

The X-ray diffraction experiments on shocked rock and mineral analogs of particular significance to lunar geology are described. Materials naturally shocked by meteorite impact, nuclear-shocked, or artificially shocked in a flat plate accelerator were utilized. Four areas were outlined for investigation: powder diffractometer studies of shocked single crystal silicate minerals (quartz, orthoclase, oligoclase, pyroxene), powder diffractometer studies of shocked polycrystalline monomineralic samples (dunite), Debye-Scherrer studies of single grains of shocked granodiorite, and powder diffractometer studies of shocked whole rock samples. Quantitative interpretation of peak shock pressures experienced by materials found in lunar or terrestrial impact structures is presented.

Interactive effects of vitamin D3 and strontium on performance, nutrient retention and bone mineral composition in laying hens.

PubMed

Browning, Linda C; Cowieson, Aaron J

2015-03-30

Strontium is currently prescribed for patients with osteoporosis to increase bone density and reduce bone fractures but its relevance in animal nutrition is obscure. In order to investigate the effect of supplemental strontium and vitamin D3 on performance, egg quality and skeletal integrity in poultry a total of 108 laying hens, 99 weeks of age, were fed three levels of strontium (0, 500, 1000 mg kg(-1) ) and two levels of vitamin D3 (2500, 5,000 iu kg(-1)) over a 12-week period. There was an improvement (P < 0.05) in egg production and feed conversion efficiency with strontium at 500 mg kg(-1) and a significant increase in egg weight in those hens fed additional vitamin D3 . Supplemental strontium increased phosphorus, sodium and strontium retention in birds fed 2500 iu D3 kg(-1) but reduced phosphorus, sodium and strontium retention in birds fed 5000 iu D3 kg(-1), resulting in an interaction (P < 0.01) between strontium and vitamin D3 . Addition of 5000 iu D3 kg(-1) increased egg weight (P < 0.05); predominantly by increased albumen content (P < 0.05), whereas strontium supplementation reduced egg weight (P < 0.001). Similarly, 5000 iu kg(-1) D3 increased apparent metabolizable energy (P < 0.05); in contrast, strontium supplementation reduced (P < 0.05) apparent metabolizable energy. The addition of 500 mg kg(-1) strontium significantly improved egg production and feed efficiency; however, further investigation needs to be undertaken to refine the optimum level of strontium required to maximize hen performance. The interrelationship between strontium and vitamin D3 requires further exploratory study. © 2014 Society of Chemical Industry.

Time-of-flight Extreme Environment Diffractometer at the Helmholtz-Zentrum Berlin

DOE Office of Scientific and Technical Information (OSTI.GOV)

Prokhnenko, Oleksandr, E-mail: prokhnenko@helmholtz-berlin.de; Stein, Wolf-Dieter; Bleif, Hans-Jürgen

2015-03-15

The Extreme Environment Diffractometer (EXED) is a new neutron time-of-flight instrument at the BER II research reactor at the Helmholtz-Zentrum Berlin, Germany. Although EXED is a special-purpose instrument, its early construction made it available for users as a general-purpose diffractometer. In this respect, EXED became one of the rare examples, where the performance of a time-of-flight diffractometer at a continuous source can be characterized. In this paper, we report on the design and performance of EXED with an emphasis on the unique instrument capabilities. The latter comprise variable wavelength resolution and wavelength band, control of the incoming beam divergence, themore » possibility to change the angular positions of detectors and their distance to the sample, and use of event recording and offline histogramming. These features combined make EXED easily tunable to the requirements of a particular problem, from conventional diffraction to small angle neutron scattering. The instrument performance is demonstrated by several reference measurements and user experiments.« less

[Detection of tibial condylar fractures using 3D imaging with a mobile image amplifier (Siemens ISO-C-3D): Comparison with plain films and spiral CT].

PubMed

Kotsianos, D; Rock, C; Wirth, S; Linsenmaier, U; Brandl, R; Fischer, T; Euler, E; Mutschler, W; Pfeifer, K J; Reiser, M

2002-01-01

To analyze a prototype mobile C-arm 3D image amplifier in the detection and classification of experimental tibial condylar fractures with multiplanar reconstructions (MPR). Human knee specimens (n = 22) with tibial condylar fractures were examined with a prototype C-arm (ISO-C-3D, Siemens AG), plain films (CR) and spiral CT (CT). The motorized C-arm provides fluoroscopic images during a 190 degrees orbital rotation computing a 119 mm data cube. From these 3D data sets MP reconstructions were obtained. All images were evaluated by four independent readers for the detection and assessment of fracture lines. All fractures were classified according to the Müller AO classification. To confirm the results, the specimens were finally surgically dissected. 97 % of the tibial condylar fractures were easily seen and correctly classified according to the Müller AO classification on MP reconstruction of the ISO-C-3D. There is no significant difference between ISO-C and CT in detection and correct classification of fractures, but ISO-CD-3D is significant by better than CR. The evaluation of fractures with the ISO-C is better than with plain films alone and comparable to CT scans. The three-dimensional reconstruction of the ISO-C can provide important information which cannot be obtained from plain films. The ISO-C-3D may be useful in planning operative reconstructions and evaluating surgical results in orthopaedic surgery of the limbs.

An X-ray diffractometer using mirage diffraction

PubMed Central

Fukamachi, Tomoe; Jongsukswat, Sukswat; Ju, Dongying; Negishi, Riichirou; Hirano, Keiichi; Kawamura, Takaaki

2014-01-01

Some characteristics are reported of a triple-crystal diffractometer with a (+, −, +) setting of Si(220) using mirage diffraction. The first crystal is flat, while the second and third crystals are bent. Basically, the first crystal is used as a collimator, the second as a monochromator and the third as the sample. The third crystal also works as an analyzer. The advantages of this diffractometer are that its setup is easy, its structure is simple, the divergence angle from the second crystal is small and the energy resolution of the third crystal is high, of the order of sub-meV. PMID:25242911

Design and implementation of a multiaxial loading capability during heating on an engineering neutron diffractometer

DOE PAGES

Benafan, O.; Padula, S. A.; Skorpenske, H. D.; ...

2014-10-02

Here we discuss a gripping capability that was designed, implemented, and tested for in situ neutron diffraction measurements during multiaxial loading and heating on the VULCAN engineering materials diffractometer at the spallation neutron source at Oak Ridge National Laboratory.

Shielding evaluation for IMRT implementation in an existing accelerator vault

PubMed Central

Price, R. A.; Chibani, O.; Ma, C.‐M.

2003-01-01

A formalism is developed for evaluating the shielding in an existing vault to be used for IMRT. Existing exposure rate measurements are utilized as well as a newly developed effective modulation scaling factor. Examples are given for vaults housing 6, 10 and 18 MV linear accelerators. The use of an 18 MV Siemens linear accelerator is evaluated for IMRT delivery with respect to neutron production and the effects on individual patients. A modified modulation scaling factor is developed and the risk of the incurrence of fatal secondary malignancies is estimated. The difference in neutron production between 18 MV Varian and Siemens accelerators is estimated using Monte Carlo results. The neutron production from the Siemens accelerator is found to be approximately 4 times less than that of the Varian accelerator resulting in a risk of fatal secondary malignancy occurrence of approximately 1.6% when using the SMLC delivery technique and our measured modulation scaling factors. This compares with a previously published value of 1.6% for routine 3D CRT delivery on the Varian accelerator. PACS number(s): 87.52.Ga, 87.52.Px, 87.53.Qc, 87.53.Wz PMID:12841794

Solid Oxide Fuel Cells Operating on Alternative and Renewable Fuels

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Xiaoxing; Quan, Wenying; Xiao, Jing

2014-09-30

This DOE project at the Pennsylvania State University (Penn State) initially involved Siemens Energy, Inc. to (1) develop new fuel processing approaches for using selected alternative and renewable fuels – anaerobic digester gas (ADG) and commercial diesel fuel (with 15 ppm sulfur) – in solid oxide fuel cell (SOFC) power generation systems; and (2) conduct integrated fuel processor – SOFC system tests to evaluate the performance of the fuel processors and overall systems. Siemens Energy Inc. was to provide SOFC system to Penn State for testing. The Siemens work was carried out at Siemens Energy Inc. in Pittsburgh, PA. Themore » unexpected restructuring in Siemens organization, however, led to the elimination of the Siemens Stationary Fuel Cell Division within the company. Unfortunately, this led to the Siemens subcontract with Penn State ending on September 23rd, 2010. SOFC system was never delivered to Penn State. With the assistance of NETL project manager, the Penn State team has since developed a collaborative research with Delphi as the new subcontractor and this work involved the testing of a stack of planar solid oxide fuel cells from Delphi.« less

Motorized Beam Alignment of a Commercial X-ray Diffractometer

NASA Technical Reports Server (NTRS)

Van Zandt, Noah R.; Myers, James F.; Rogers, Richard B

2013-01-01

X-ray diffraction (XRD) is a powerful analysis method that allows researchers to noninvasively probe the crystalline structure of a material. This includes the ability to determine the crystalline phases present, quantify surface residual stresses, and measure the distribution of crystallographic orientations. The Structures and Materials Division at the NASA Glenn Research Center (GRC) heavily uses the on-site XRD lab to characterize advanced metal alloys, ceramics, and polymers. One of the x-ray diffractometers in the XRD lab (Bruker D8 Discover) uses three different x-ray tubes (Cu, Cr, and Mn) for optimal performance over numerous material types and various experimental techniques. This requires that the tubes be switched out and aligned between experiments. This alignment maximizes the x-ray tube s output through an iterative process involving four set screws. However, the output of the x-ray tube cannot be monitored during the adjustment process due to standard radiation safety engineering controls that prevent exposure to the x-ray beam when the diffractometer doors are open. Therefore, the adjustment process is a very tedious series of blind adjustments, each followed by measurement of the output beam using a PIN diode after the enclosure doors are shut. This process can take up to 4 hr to perform. This technical memorandum documents an in-house project to motorize this alignment process. Unlike a human, motors are not harmed by x-ray radiation of the energy range used in this instrument. Therefore, using motors to adjust the set screws will allow the researcher to monitor the x-ray tube s output while making interactive adjustments from outside the diffractometer. The motorized alignment system consists of four motors, a motor controller, and a hand-held user interface module. Our goal was to reduce the alignment time to less than 30 min. The time available was the 10-week span of the Lewis' Educational and Research Collaborative Internship Project (LERCIP) summer internship program and the budget goal was $1200. In this report, we will describe our motorization design and discuss the results of its implementation.

Unusual Thermal Stability of High-Entropy Alloy Amorphous Structure

DTIC Science & Technology

2012-06-20

incident angle X - ray diffractometer (GIAXRD, RIGAKU D/MAX2500) with Cu Kα radiation and at the incident angle of 1°. The surface morphology and...microanalyzer (EPMA, JEOL JAX-8800). The crystallographic structures of as-deposited and annealed metallic films were characterized utilizing a glancing ...field image and selected-area- diffraction (SAD) patterns of (a) 800 °C-, (b) 850 °C- and (c) 900 °C-annealed alloy thin films, respectively. Both

Development of a position sensitive X-ray detector for use in a light weight X-ray diffractometer

NASA Technical Reports Server (NTRS)

Semmler, R. A.

1971-01-01

A position sensitive proportional counter for use in an X-ray diffractometer is developed to permit drastic reductions in the power and weight requirements of the X-ray source and the elimination of the power, weight, and complexity of a moving slit. The final detector constructed and tested has a window spanning 138 and a free standing anode curved along an arc of 7.1 cm radius. Demonstration spectra of a quartz sample in a Debye-Sherrer geometry indicate a spatial resolution of 0.4 - 0.5 mm (0.3 - 0.4 theta). The lunar diffractometer consumed 25 watts in the X-ray generator and weighed about 20 pounds.

Fabrications and application of single crystalline GaN for high-performance deep UV photodetectors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Velazquez, R.; Rivera, M.; Feng, P., E-mail: p.feng@upr.edu

2016-08-15

High-quality single crystalline Gallium Nitride (GaN) semiconductor has been synthesized using molecule beam epitaxy (MBE) technique for development of high-performance deep ultraviolet (UV) photodetectors. Thickness of the films was estimated by using surface profile meter and scanning electron microscope. Electronic states and elemental composition of the films were obtained using Raman scattering spectroscopy. The orientation, crystal structure and phase purity of the films were examined using a Siemens x-ray diffractometer radiation. The surface microstructure was studied using high resolution scanning electron microscopy (SEM). Two types of metal pairs: Al-Al, Al-Cu or Cu-Cu were used for interdigital electrodes on GaN filmmore » in order to examine the Schottky properties of the GaN based photodetector. The characterizations of the fabricated prototype include the stability, responsivity, response and recovery times. Typical time dependent photoresponsivity by switching different UV light source on and off five times for each 240 seconds at a bias of 2V, respectively, have been obtained. The detector appears to be highly sensitive to various UV wavelengths of light with very stable baseline and repeatability. The obtained photoresponsivity was up to 354 mA/W at the bias 2V. Higher photoresponsivity could be obtained if higher bias was applied but it would unavoidably result in a higher dark current. Thermal effect on the fabricated GaN based prototype was discussed.« less

Optimization of a multi-channel parabolic guide for the material science diffractometer STRESS-SPEC at FRM II

NASA Astrophysics Data System (ADS)

Rebelo Kornmeier, Joana; Ostermann, Andreas; Hofmann, Michael; Gibmeier, Jens

2014-02-01

Neutron strain diffractometers usually use slits to define a gauge volume within engineering samples. In this study a multi-channel parabolic neutron guide was developed to be used instead of the primary slit to minimise the loss of intensity and vertical definition of the gauge volume when using slits placed far away from the measurement position in bulky components. The major advantage of a focusing guide is that the maximum flux is not at the exit of the guide as for a slit system but at the focal point relatively far away from the exit of the guide. Monte Carlo simulations were used to optimise the multi-channel parabolic guide with respect to the instrument characteristics of the diffractometer STRESS-SPEC at the FRM II neutron source. Also the simulations are in excellent agreement with experimental measurements using the optimised multi-channel parabolic guide at the neutron diffractometer. In addition the performance of the guide was compared to the standard slit setup at STRESS-SPEC using a single bead weld sample used in earlier round robin tests for residual strain measurements.

49 CFR Appendix B to Part 229 - Schedule of Civil Penalties 1

Code of Federal Regulations, 2011 CFR

2011-10-01

... 229.73Wheel sets 2,500 5,000 229.75Wheel and tire defects: (a),(d) Slid flat or shelled spot(s): (1) One spot 21/2″ or more but less than 3″ in length 2,500 5,000 (2) One spot 3″ or more in length 5,000 7,500 (3) Two adjoining spots each of which is 2″ or more in length but less than 21/2″ in length 2...

49 CFR Appendix B to Part 229 - Schedule of Civil Penalties 1

Code of Federal Regulations, 2010 CFR

2010-10-01

... 229.73Wheel sets 2,500 5,000 229.75Wheel and tire defects: (a),(d) Slid flat or shelled spot(s): (1) One spot 21/2″ or more but less than 3″ in length 2,500 5,000 (2) One spot 3″ or more in length 5,000 7,500 (3) Two adjoining spots each of which is 2″ or more in length but less than 21/2″ in length 2...

Mesoporous Nitrogen Doped Carbon-Glass Ceramic Cathode for High Performance Lithium-Oxygen Battery

DTIC Science & Technology

2012-06-01

dry room with controlled moisture content. Composite 3 films on nickel foam were used as working cathodes along with lithium metal as anode and the...cathode formulation [6,7,8,9,10], efficient oxygen reduction catalysts [11,12], electrolyte compositions [13,14], effect of moisture [15], etc...specimens. Structure and purity of these materials were performed by powder X-ray diffraction (XRD) on a Rigaku D/MAX-2250 diffractometer fitted with CuKα

76 FR 32228 - Notice of Determinations Regarding Eligibility To Apply for Worker Adjustment Assistance

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-03

... identified by name by the International Trade Commission as a member of a domestic industry in an... (Formerly Enterprise Unix Division). 75,052 Siemen's Industry, Inc.. Columbus, OH....... 75,066 General... Music Holdings Pitman, NJ......... Inc., D/B/A Sony DADC Americas (``SMHI''), Sony Corporation of...

32 CFR 865.101 - References.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Freedom of Information Act Program,” March 24, 1980; title 5 U.S.C., section 552. (h) DOD Directive 5400...) DOD Directive 5000.19, “Policies for the Management and Control of Information Requirements,” March 12, 1976. (d) DOD Directive 5000.11, “Data Elements and Data Codes Standardization Program,” December 7...

76 FR 51402 - Manufacturer of Controlled Substances; Notice of Registration

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-18

..., 2011, 76 FR 25375, Siemens Healthcare Diagnostics Inc., Attn: RA, 100 GBC Drive, Mail Stop 514, Newark.... 823(a) and determined that the registration of Siemens Healthcare Diagnostics Inc., to manufacture the... has investigated Siemens Healthcare Diagnostics Inc., to ensure that the company's registration is...

POWTEX Neutron Diffractometer at FRM II - New Perspectives in Rock Deformation and Recrystallisation Analysis

NASA Astrophysics Data System (ADS)

Walter, J. M.; Stipp, M.; Ullemeyer, K.; Klein, H.; Leiss, B.; Hansen, B.; Kuhs, W. F.

2011-12-01

Neutron diffraction has become a routine method in Geoscience for the quantitative analysis of crystallographic preferred orientations (CPOs) and for (experimental) powder diffraction. Quantitative texture analysis is a common tool for the investigation of fabric development in mono- and polyphase rocks, their deformation histories and kinematics. Furthermore the quantitative characterization of anisotropic physical properties by bulk texture measurements can be achieved due to the high penetration capabilities of neutrons. To cope with increasing needs for beam time at neutron diffraction facilities with the corresponding technical characteristics and equipment, POWTEX (POWder and TEXture Diffractometer) is designed as a high-intensity diffractometer at the neutron research reactor FRM II in Garching, Germany by groups from the RWTH Aachen, Forschungszentrum Jülich and the University of Göttingen. Complementary to existing neutron diffractometers (SKAT at Dubna, Russia; GEM at ISIS, UK; HIPPO at Los Alamos, USA; D20 at ILL, France; and the local STRESS-SPEC and SPODI at FRM II) the layout of POWTEX is focused on fast (texture) measurements for either time-resolved experiments or the measurement of larger sample series as necessary for the study of large scale geological structures. By utilizing a range of neutron wavelengths simultaneously (TOF-technique), a high flux (~1 x 107 n/cm2s) and a high detector coverage ( 9.8 sr) effective texture measurements without sample tilting and rotation are possible. Furthermore the instrument and the angular detector resolution is sufficient for strong recrystallisation textures as well as weak textures of polyphase rocks. Thereby large sample environments will be implemented at POWTEX allowing in-situ time-resolved texture measurements during deformation experiments on rocksalt, ice and other materials. Furthermore a furnace for 3D-recrystallisation analysis of single grains will be realized complementary to the furnace that already exists for fine grained materials at the synchrotron beamline BW5 at HASYLAB, Germany (e.g. Klein et al. 2009). The in-situ triaxial deformation apparatus is operated by a uniaxial spindle drive with a maximum axial load of 200 kN, which will be redesigned to minimize shadowing effects on the detector. The HT experiments will be carried out in uniaxial compression or extension and an upgrade to triaxial deformation conditions is envisaged. The load frame can alternatively be used for ice deformation by inserting a cryostat cell for temperatures down to 77 K with a triaxial apparatus allowing also simple shear experiments on ice. Strain rates range between 10-8 and 10-3 s-1 reaching to at least 50 % axial strain. The furnace for the recrystallization analysis will be a mirror furnace with temperatures up to 1500° C, which will be rotatable around a vertical axis to obtain the required stereologic orientation information.

Modifications to the XBR-2D Heat Conduction Code

DTIC Science & Technology

1994-04-01

for & 25-me barrel (750 Shots/min) is A mbient Tm 4R), Pr fpsi), gas vel (in/s) z : -....-.. -... .... : 530.0 14.70 0.00 b Sarrel Gemetry : ; zchrom...Ausomotive Command U.S. Army Maeiel Cummand ATTN: AMSTA-JSK (Armor Eeg . Br.) ATII: AMCAM Wre, MI 4897.5000 5001 Eisenhower Ave. Alexandria, VA 22333.001 1...and Engeering Center A er Prving ATTN.4 SMCAR- TDC Picauinny Arsenal l 07806-5000 2 Dir, USAMSAA ATTN: AMXSY-D Direcior AMXSY-MP, IL Cohe DenK Weapomn

77 FR 30518 - Town of Springfield, Vermont and Siemens Westinghouse Technical Services, Inc., One Hundred River...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-23

... DEPARTMENT OF ENERGY Federal Energy Regulatory Commission [Project No. 9648-018] Town of Springfield, Vermont and Siemens Westinghouse Technical Services, Inc., One Hundred River Street, LLC; Notice... 15, 2011 and supplemented on April 27, 2012, the Town of Springfield, Vermont and Siemens...

75 FR 69466 - Manufacturer of Controlled Substances; Notice of Registration

Federal Register 2010, 2011, 2012, 2013, 2014

2010-11-12

..., 2010, (75 FR 20001), Siemens Healthcare Diagnostics Inc., Attn: RA, 100 GBC Drive, Mail Stop 514... Siemens Healthcare Diagnostics Inc. to manufacture the listed basic classes of controlled substances is consistent with the public interest at this time. DEA has investigated Siemens Healthcare Diagnostics Inc. to...

77 FR 31390 - Manufacturer of Controlled Substances; Notice of Registration; Siemens Healthcare Diagnostics, Inc.

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-25

...; Notice of Registration; Siemens Healthcare Diagnostics, Inc. By Notice dated January 26, 2012, and published in the Federal Register on February 6, 2012, 77 FR 5847, Siemens Healthcare Diagnostics Inc., 100... Healthcare Diagnostics Inc., to manufacture the listed basic classes of controlled substances is consistent...

77 FR 72409 - Manufacturer of Controlled Substances; Notice of Application: Siemens Healthcare Diagnostics, Inc.

Federal Register 2010, 2011, 2012, 2013, 2014

2012-12-05

... DEPARTMENT OF JUSTICE Drug Enforcement Administration Manufacturer of Controlled Substances; Notice of Application: Siemens Healthcare Diagnostics, Inc. Pursuant to Sec. 1301.33(a) Title 21 of the Code of Federal Regulations (CFR), this is notice that on November 7, 2012, Siemens Healthcare...

Better powder diffractometers. II—Optimal choice of U, V and W

NASA Astrophysics Data System (ADS)

Cussen, L. D.

2007-12-01

This article presents a technique for optimising constant wavelength (CW) neutron powder diffractometers (NPDs) using conventional nonlinear least squares methods. This is believed to be the first such design optimisation for a neutron spectrometer. The validity of this approach and discussion should extend beyond the Gaussian element approximation used and also to instruments using different radiation, such as X-rays. This approach could later be extended to include vertical and perhaps horizontal focusing monochromators and probably other types of instruments such as three axis spectrometers. It is hoped that this approach will help in comparisons of CW and time-of-flight (TOF) instruments. Recent work showed that many different beam element combinations can give identical resolution on CW NPDs and presented a procedure to find these combinations and also find an "optimum" choice of detector collimation. Those results enable the previous redundancy in the description of instrument performance to be removed and permit a least squares optimisation of design. New inputs are needed and are identified as the sample plane spacing ( dS) of interest in the measurement. The optimisation requires a "quality factor", QPD, chosen here to be minimising the worst Bragg peak separation ability over some measurement range ( dS) while maintaining intensity. Any other QPD desired could be substituted. It is argued that high resolution and high intensity powder diffractometers (HRPDs and HIPDs) should have similar designs adjusted by a single scaling factor. Simulated comparisons are described suggesting significant improvements in performance for CW HIPDs. Optimisation with unchanged wavelength suggests improvements by factors of about 2 for HRPDs and 25 for HIPDs. A recently quantified design trade-off between the maximum line intensity possible and the degree of variation of angular resolution over the scattering angle range leads to efficiency gains at short wavelengths. This in turn leads in practice to another trade-off between this efficiency gain and losses at short wavelength due to technical effects. The exact gains from varying wavelength depend on the details of the short wavelength technical losses. Simulations suggest that the total potential PD performance gains may be very significant-factors of about 3 for HRPDs and more than 90 for HIPDs.

76 FR 50269 - Amended Certification Regarding Eligibility To Apply for Worker Adjustment Assistance

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-12

... Solutions USA, Inc., Oncology Care Systems Division, Concord, CA TA-W-73,158A Siemens Medical Solutions USA... and former workers of Siemens Medical Solutions USA, Inc. (Seimens), Oncology Care Systems Division... issued as follows: All workers of Siemens Medical Solutions USA, Inc., Oncology Care Systems Division...

ETV Report: Siemens Model V-40R-A150 Open Channel UV System

EPA Science Inventory

Verification testing of the Siemens Barrier Sunlight V-40R-A150 UV System was completed at the UV Validation and Research Center of New York (UV Center), located in Johnstown, NY. The V-40R System supplied by Siemens utilizes 40 high-output, low-pressure amalgam lamps, oriented ...

Feasibility and validation of virtual autopsy for dental identification using the Interpol dental codes.

PubMed

Franco, Ademir; Thevissen, Patrick; Coudyzer, Walter; Develter, Wim; Van de Voorde, Wim; Oyen, Raymond; Vandermeulen, Dirk; Jacobs, Reinhilde; Willems, Guy

2013-05-01

Virtual autopsy is a medical imaging technique, using full body computed tomography (CT), allowing for a noninvasive and permanent observation of all body parts. For dental identification clinically and radiologically observed ante-mortem (AM) and post-mortem (PM) oral identifiers are compared. The study aimed to verify if a PM dental charting can be performed on virtual reconstructions of full-body CT's using the Interpol dental codes. A sample of 103 PM full-body CT's was collected from the forensic autopsy files of the Department of Forensic Medicine University Hospitals, KU Leuven, Belgium. For validation purposes, 3 of these bodies underwent a complete dental autopsy, a dental radiological and a full-body CT examination. The bodies were scanned in a Siemens Definition Flash CT Scanner (Siemens Medical Solutions, Germany). The images were examined on 8- and 12-bit screen resolution as three-dimensional (3D) reconstructions and as axial, coronal and sagittal slices. InSpace(®) (Siemens Medical Solutions, Germany) software was used for 3D reconstruction. The dental identifiers were charted on pink PM Interpol forms (F1, F2), using the related dental codes. Optimal dental charting was obtained by combining observations on 3D reconstructions and CT slices. It was not feasible to differentiate between different kinds of dental restoration materials. The 12-bit resolution enabled to collect more detailed evidences, mainly related to positions within a tooth. Oral identifiers, not implemented in the Interpol dental coding were observed. Amongst these, the observed (3D) morphological features of dental and maxillofacial structures are important identifiers. The latter can become particularly more relevant towards the future, not only because of the inherent spatial features, yet also because of the increasing preventive dental treatment, and the decreasing application of dental restorations. In conclusion, PM full-body CT examinations need to be implemented in the PM dental charting protocols and the Interpol dental codes should be adapted accordingly. Copyright © 2012 Elsevier Ltd and Faculty of Forensic and Legal Medicine. All rights reserved.

Company Information on CD-ROM: From 10K to 5000+.

ERIC Educational Resources Information Center

Littlejohn, Alice C.; Janousek, Kelly S.

1991-01-01

Evaluates six CD-ROM products for library users that provide information on companies: (1) CD/Corporate: U.S. Public Companies; (2) Compact D/SEC; (3) Compustat PC Plus Corporate Text; (4) General Business File; (5) Moody's 5000 Plus; and (6) Standard and Poor's Corporations. Information provided includes companies included, online database…

25OHD analogues and vacuum blood collection tubes dramatically affect the accuracy of automated immunoassays

PubMed Central

Yu, Songlin; Cheng, Xinqi; Fang, Huiling; Zhang, Ruiping; Han, Jianhua; Qin, Xuzhen; Cheng, Qian; Su, Wei; Hou, Li’an; Xia, Liangyu; Qiu, Ling

2015-01-01

Variations in vitamin D quantification methods are large, and influences of vitamin D analogues and blood collection methods have not been systematically examined. We evaluated the effects of vitamin D analogues 25OHD2 and 3-epi 25OHD3 and blood collection methods on vitamin D measurement, using five immunoassay systems and liquid chromatography-tandem mass spectrometry (LC-MS/MS). Serum samples (332) were selected from routine vitamin D assay requests, including samples with or without 25OHD2 or 3-epi 25OHD3, and analysed using various immunoassay systems. In samples with no 25OHD2 or 3-epi 25OHD3, all immunoassays correlated well with LC-MS/MS. However, the Siemens system produced a large positive mean bias of 12.5 ng/mL and a poor Kappa value when using tubes with clot activator and gel separator. When 25OHD2 or 3-epi 25OHD3 was present, correlations and clinical agreement decreased for all immunoassays. Serum 25OHD in VACUETTE tubes with gel and clot activator, as measured by the Siemens system, produced significantly higher values than did samples collected in VACUETTE tubes with no additives. Bias decreased and clinical agreement improved significantly when using tubes with no additives. In conclusion, most automated immunoassays showed acceptable correlation and agreement with LC-MS/MS; however, 25OHD analogues and blood collection tubes dramatically affected accuracy. PMID:26420221

25OHD analogues and vacuum blood collection tubes dramatically affect the accuracy of automated immunoassays.

PubMed

Yu, Songlin; Cheng, Xinqi; Fang, Huiling; Zhang, Ruiping; Han, Jianhua; Qin, Xuzhen; Cheng, Qian; Su, Wei; Hou, Li'an; Xia, Liangyu; Qiu, Ling

2015-09-30

Variations in vitamin D quantification methods are large, and influences of vitamin D analogues and blood collection methods have not been systematically examined. We evaluated the effects of vitamin D analogues 25OHD2 and 3-epi 25OHD3 and blood collection methods on vitamin D measurement, using five immunoassay systems and liquid chromatography-tandem mass spectrometry (LC-MS/MS). Serum samples (332) were selected from routine vitamin D assay requests, including samples with or without 25OHD2 or 3-epi 25OHD3, and analysed using various immunoassay systems. In samples with no 25OHD2 or 3-epi 25OHD3, all immunoassays correlated well with LC-MS/MS. However, the Siemens system produced a large positive mean bias of 12.5 ng/mL and a poor Kappa value when using tubes with clot activator and gel separator. When 25OHD2 or 3-epi 25OHD3 was present, correlations and clinical agreement decreased for all immunoassays. Serum 25OHD in VACUETTE tubes with gel and clot activator, as measured by the Siemens system, produced significantly higher values than did samples collected in VACUETTE tubes with no additives. Bias decreased and clinical agreement improved significantly when using tubes with no additives. In conclusion, most automated immunoassays showed acceptable correlation and agreement with LC-MS/MS; however, 25OHD analogues and blood collection tubes dramatically affected accuracy.

Comparison of effects of dose on image quality in digital breast tomosynthesis across multiple vendors

NASA Astrophysics Data System (ADS)

Zhao, Amy; Santana, Maira; Samei, Ehsan; Lo, Joseph

2017-03-01

In traditional radiography and computed tomography (CT), contrast is an important measure of image quality that, in theory, does not vary with dose. While increasing dose may increase the overall contrast-to-noise ratio (CNR), the contrast in an image should be primarily dependent on variation in tissue density and attenuation. We investigated the behavior of all three currently FDA-approved vendors' 3D DBT systems (Siemens, Hologic, and General Electric (GE)) using the Computerized Imaging Reference Systems (CIRS) Model 011A Breast Phantom and found that for both Siemens and Hologic systems, contrast increased with dose across multiple repeated trials. For these two systems, experimental CNR also appeared to increase above the expected CNR, which suggests that these systems seem to have introduced post-processing by manipulation of contrast, and thus DBT data cannot be used to reliably quantify tissue characteristics. Additional experimentation with both 2D mammography and 3D DBT systems from GE in addition to the previously mentioned vendors, however, suggested that this relationship is not true for all systems. An initial comparison of contrast vs. dose showed no relationship between contrast and dose for 2D mammography, with the contrast remaining relatively constant in the dose range of 33% of the automatic exposure control setting (AEC) to 300% AEC for all three vendors. The GE DBT system also did not exhibit increased contrast with increased dose, suggesting that the behavior of 3D DBT systems is vendor-specific.

Neutron diffraction study of aqueous Laponite suspensions at the NIMROD diffractometer.

PubMed

Tudisca, V; Bruni, F; Scoppola, E; Angelini, R; Ruzicka, B; Zulian, L; Soper, A K; Ricci, M A

2014-09-01

The process of dynamical arrest, leading to formation of different arrested states such as glasses and gels, along with the closely related process of aging, is central for both basic research and technology. Here we report on a study of the time-dependent structural evolution of two aqueous Laponite clay suspensions at different weight concentrations. Neutron diffraction experiments have been performed with the near and intermediate range order diffractometer (NIMROD) that allows studies of the structure of liquids and disordered materials over a continuous length scale ranging from 1 to 300 Å, i.e., from the atomistic to the mesoscopic scales. NIMROD is presently a unique diffractometer, bridging the length scales traditionally investigated by small angle neutron scattering or small angle x-ray scattering with that accessible by traditional diffractometers for liquids. Interestingly, we have unveiled a signature of aging of both suspensions in the length scale region of NIMROD. This phenomenon, ascribed to sporadic contacts between Laponite platelets at long times, has been observed with the sample arrested as gel or as repulsive glass. Moreover, water molecules within the layers closest to Laponite platelets surface show orientational and translational order, which maps into the crystalline structure of Laponite.

Diffractometer data collecting method and apparatus

DOEpatents

Steinmeyer, P.A.

1991-04-16

Diffractometer data is collected without the use of a movable receiver. A scanning device, positioned in the diffractometer between a sample and detector, varies the amount of the beam diffracted from the sample that is received by the detector in such a manner that the beam is detected in an integrated form. In one embodiment, a variable diameter beam stop is used which comprises a drop of mercury captured between a pair of spaced sheets and disposed in the path of the diffracted beam. By varying the spacing between the sheets, the diameter of the mercury drop is varied. In another embodiment, an adjustable iris diaphragm is positioned in the path of the diffracted beam and the iris opening is adjusted to control the amount of the beam reaching the detector. 5 figures.

Diffractometer data collecting method and apparatus

DOEpatents

Steinmeyer, Peter A.

1991-04-16

Diffractometer data is collected without the use of a movable receiving s. A scanning device, positioned in the diffractometer between a sample and detector, varies the amount of the beam diffracted from the sample that is received by the detector in such a manner that the beam is detected in an integrated form. In one embodiment, a variable diameter beam stop is used which comprises a drop of mercury captured between a pair of spaced sheets and disposed in the path of the diffracted beam. By varying the spacing between the sheets, the diameter of the mercury drop is varied. In another embodiment, an adjustable iris diaphragm is positioned in the path of the diffracted beam and the iris opening is adjusted to control the amount of the beam reaching the detector.

Calibration of X-Ray diffractometer by the experimental comparison method

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dudka, A. P., E-mail: dudka@ns.crys.ras.ru

2015-07-15

A software for calibrating an X-ray diffractometer with area detector has been developed. It is proposed to search for detector and goniometer calibration models whose parameters are reproduced in a series of measurements on a reference crystal. Reference (standard) crystals are prepared during the investigation; they should provide the agreement of structural models in repeated analyses. The technique developed has been used to calibrate Xcalibur Sapphire and Eos, Gemini Ruby (Agilent) and Apex x8 and Apex Duo (Bruker) diffractometers. The main conclusions are as follows: the calibration maps are stable for several years and can be used to improve structuralmore » results, verified CCD detectors exhibit significant inhomogeneity of the efficiency (response) function, and a Bruker goniometer introduces smaller distortions than an Agilent goniometer.« less

Anomalous Orthopyroxene Cell Volumes from Unshocked Equilibrated H Chondrites

NASA Astrophysics Data System (ADS)

Folco, L.; Mellini, M.; Pillinger, C. T.

1995-09-01

Thirteen orthopyroxenes were extracted from eight unshocked equilibrated H-chondrites representatives of the petrographic types 4 to 6 [1] for crystal-chemical analyses. Chemical compositions were determined through a WDS JEOL JX 8600 electron microprobe. Three to six spot analyses were run on each crystal and no significant chemical variation was detected. High quality single crystal X-ray diffraction data were obtained by a SIEMENS P4 diffractometer using MoK alpha radiation, and site occupancies by least squares structure refinements. Figure 1a shows a significant cell volume (Vc) increase with petrographic type, and a _1.5 Angstrom^3 spread within each petrographic type. In solid solutions, Vc is expected to mainly vary with the chemical composition: the higher the proportion of the large ions present, the larger the Vc. In particular, as shown by [2], Vc variations in orthopyroxenes are essentially linear with Fe/(Fe+Mg), and our data fall within this general trend. However, no such a correlation exists at the scale of our values (Fig.1b), rather, each petrographic type plots along a different roughly negative trend. Furthermore, as experimentally obtained by [3], the decrease of the Fe-Mg ordering between the M1 and M2 sites in orthopyroxenes (a temperature-time-dependent process), causes significant Vc increase due to the displacement of the large Fe2+ ions from the larger M2 to the smaller M1 sites. Again, in the Vc versus kD (i.e., the intracrystalline Fe-Mg distribution coefficient) diagram (Fig.1c), we observe no such a correlation. Contrary to the most immediate expectations, our data suggest that the net increase in Vc from H4 to H6 does not significantly depend upon chemical composition and degree of ordering, and demands that another as yet unidentified parameter accounts for the observed trends. Acknowledgments: We thank EUROMET for the Frontier Mt. samples, and PNRA for supporting this study. References: [1] Folco L. et al., this volume. [2] Sykes-Nord J. A. and Molin G. M. (1993) Am. Mineral., 78, 921-931. [3] Domeneghetti M. C. et al. (1985). Am. Mineral., 70, 987-995.

78 FR 41911 - Foreign-Trade Zone 161-Sedgwick County, Kansas; Authorization of Production Activity; Siemens...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-12

... DEPARTMENT OF COMMERCE Foreign-Trade Zones Board [B-27-2013] Foreign-Trade Zone 161--Sedgwick County, Kansas; Authorization of Production Activity; Siemens Energy, Inc. (Wind Turbine Nacelles and Hubs); Hutchinson, Kansas On March 7, 2013, Siemens Energy, Inc., an operator of FTZ 161, submitted a notification of proposed production activity to...

Clinical validation of an in-house EPID dosimetry system for IMRT QA at the Prince of Wales Hospital

NASA Astrophysics Data System (ADS)

Tyler, M.; Vial, P.; Metcalfe, P.; Downes, S.

2013-06-01

In this study a simple method using standard flood-field corrected Electronic Portal Imaging Device (EPID) images for routine Intensity Modulated Radiation Therapy (IMRT) Quality Assurance (QA) was investigated. The EPID QA system was designed and tested on a Siemens Oncor Impression linear accelerator with an OptiVue 1000ST EPID panel (Siemens Medical Solutions USA, Inc, USA) and an Elekta Axesse linear accelerator with an iViewGT EPID (Elekta AB, Sweden) for 6 and 10 MV IMRT fields with Step-and-Shoot and dynamic-MLC delivery. Two different planning systems were used for patient IMRT field generation for comparison with the measured EPID fluences. All measured IMRT plans had >95% agreement to the planning fluences (using 3 cGy / 3 mm Gamma Criteria) and were comparable to the pass-rates calculated using a 2-D diode array dosimeter.

Microgravity

NASA Image and Video Library

1998-06-16

Eddie Snell, Post-Doctoral Fellow the National Research Council (NRC) uses a reciprocal space mapping diffractometer for macromolecular crystal quality studies. The diffractometer is used in mapping the structure of macromolecules such as proteins to determine their structure and thus understand how they function with other proteins in the body. This is one of several analytical tools used on proteins crystallized on Earth and in space experiments. Photo credit: NASA/Marshall Space Flight Center (MSFC)

Protein Crystal Quality Studies

NASA Technical Reports Server (NTRS)

1998-01-01

Eddie Snell, Post-Doctoral Fellow the National Research Council (NRC) uses a reciprocal space mapping diffractometer for macromolecular crystal quality studies. The diffractometer is used in mapping the structure of macromolecules such as proteins to determine their structure and thus understand how they function with other proteins in the body. This is one of several analytical tools used on proteins crystallized on Earth and in space experiments. Photo credit: NASA/Marshall Space Flight Center (MSFC)

Influence of Eddy Current, Maxwell and Gradient Field Corrections on 3D Flow Visualization of 3D CINE PC-MRI Data

PubMed Central

Lorenz, R.; Bock, J.; Snyder, J.; Korvink, J.G.; Jung, B.A.; Markl, M.

2013-01-01

Purpose The measurement of velocities based on PC-MRI can be subject to different phase offset errors which can affect the accuracy of velocity data. The purpose of this study was to determine the impact of these inaccuracies and to evaluate different correction strategies on 3D visualization. Methods PC-MRI was performed on a 3 T system (Siemens Trio) for in vitro (curved/straight tube models; venc: 0.3 m/s) and in vivo (aorta/intracranial vasculature; venc: 1.5/0.4 m/s) data. For comparison of the impact of different magnetic field gradient designs, in vitro data was additionally acquired on a wide bore 1.5 T system (Siemens Espree). Different correction methods were applied to correct for eddy currents, Maxwell terms and gradient field inhomogeneities. Results The application of phase offset correction methods lead to an improvement of 3D particle trace visualization and count. The most pronounced differences were found for in vivo/in vitro data (68%/82% more particle traces) acquired with a low venc (0.3 m/s/0.4 m/s, respectively). In vivo data acquired with high venc (1.5 m/s) showed noticeable but only minor improvement. Conclusion This study suggests that the correction of phase offset errors can be important for a more reliable visualization of particle traces but is strongly dependent on the velocity sensitivity, object geometry, and gradient coil design. PMID:24006013

In vitro effect of calcium-containing prescription-strength fluoride toothpastes on bovine enamel erosion under hyposalivation-simulating conditions.

PubMed

Scaramucci, Taís; Borges, Alessandra B; Lippert, Frank; Zero, Domenick T; Hara, Anderson T

2015-02-01

To evaluate the ability of calcium-containing prescription-strength fluoride (F) toothpastes in preventing enamel erosion under low salivary flow simulating conditions. Enamel and dentin bovine specimens were assigned to the following groups: A - placebo; B - 1,100 ppm F/NaF (Aquafresh Advanced); C - 5,000 ppm F/NaF (Prevident 5000 Booster); D - 5000 ppm F/NaF+calcium sodium phosphosilicate (Topex Renew); and E - 5,000 ppm F/NaF+tri-calcium phosphate (Clinpro 5000). Specimens were positioned in custom-made devices, creating a sealed chamber on the surface, connected to peristaltic pumps. Citric acid was injected into the chamber for 2 minutes, followed by artificial saliva (0.05 ml/minute), for 60 minutes, 4x/day, for 3 days. Aquafresh was also tested under normal salivary flow (0.5 ml/minute), as reference (Group F). Specimens were exposed to the toothpastes for 2 minutes, 2x/day. After cycling, surface loss (SL) and concentration of loosely- and firmly-bound F were determined. Data were analyzed by ANOVA. Results: Group A (placebo) presented highest surface loss (SL), while Group F had the lowest, for both substrates. For enamel, none of the dentifrices differed from Group B or among each other. For dentin, none of the dentifrices differed from Group B, but Group E showed greater protection than Group C. Group E presented the highest F concentrations for both substrates, only matched by Group D for firmly-bound fluoride on enamel. All fluoridated dentifrices tested reduced SL, with no additional benefit from higher F concentrations. Some formulations, especially Clinpro 5000, increased F availability on the dental substrates, but no further erosion protection was observed.

A temperature-controlled cell for X-ray study of liquid systems using a commercial DRON-UM1 diffractometer

DOE Office of Scientific and Technical Information (OSTI.GOV)

Petrun`kin, S.P.; Garavina, E.V.; Trostin, V.N.

1995-02-01

A container (cell) and a temperature-control system have been designed enabling one to carry out x-ray diffraction study of liquid samples both at a fixed temperature and within a certain temperature range using a commercial DRON-UMl x-ray diffractometer. Special features of the cell and the materials used for it allow one to study both chemically inert and corrosive liquids.

Sample holder for X-ray diffractometry

DOEpatents

Hesch, Victor L.

1992-01-01

A sample holder for use with X-ray diffractometers with the capability to rotate the sample, as well as to adjust the position of the sample in the x, y, and z directions. Adjustment in the x direction is accomplished through loosening set screws, moving a platform, and retightening the set screws. Motion translators are used for adjustment in the y and z directions. An electric motor rotates the sample, and receives power from the diffractometer.

In-situ data collection at the photon factory macromolecular crystallography beamlines

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yamada, Yusuke, E-mail: yusuke.yamada@kek.jp; Matsugaki, Naohiro; Kato, Ryuichi

Crystallization trial is one of the most important but time-consuming steps in macromolecular crystallography, and in-situ diffraction experiment has a capability to make researchers to proceed this step more efficiently. At the Photon Factory, a new tabletop diffractometer for in-situ diffraction experiments has been developed. It consists of XYZ translation stages with a plate handler, an on-axis viewing system and a plate rack with a capacity for ten crystallization plates. These components sit on a common plate and are able to be placed on the existing diffractometer table. The CCD detector with a large active area and a pixel arraymore » detector with a small active area are used for acquiring diffraction images from crystals. Dedicated control software and a user interface have also been developed. The new diffractometer has been operational for users and used for evaluation of crystallization screening since 2014.« less

2D–3D radiograph to cone-beam computed tomography (CBCT) registration for C-arm image-guided robotic surgery

PubMed Central

Liu, Wen Pei; Otake, Yoshito; Azizian, Mahdi; Wagner, Oliver J.; Sorger, Jonathan M.; Armand, Mehran; Taylor, Russell H.

2015-01-01

Purpose C-arm radiographs are commonly used for intraoperative image guidance in surgical interventions. Fluoroscopy is a cost-effective real-time modality, although image quality can vary greatly depending on the target anatomy. Cone-beam computed tomography (CBCT) scans are sometimes available, so 2D–3D registration is needed for intra-procedural guidance. C-arm radiographs were registered to CBCT scans and used for 3D localization of peritumor fiducials during a minimally invasive thoracic intervention with a da Vinci Si robot. Methods Intensity-based 2D–3D registration of intraoperative radiographs to CBCT was performed. The feasible range of X-ray projections achievable by a C-arm positioned around a da Vinci Si surgical robot, configured for robotic wedge resection, was determined using phantom models. Experiments were conducted on synthetic phantoms and animals imaged with an OEC 9600 and a Siemens Artis zeego, representing the spectrum of different C-arm systems currently available for clinical use. Results The image guidance workflow was feasible using either an optically tracked OEC 9600 or a Siemens Artis zeego C-arm, resulting in an angular difference of Δθ : ~ 30°. The two C-arm systems provided TREmean ≤ 2.5 mm and TREmean ≤ 2.0 mm, respectively (i.e., comparable to standard clinical intraoperative navigation systems). Conclusions C-arm 3D localization from dual 2D–3D registered radiographs was feasible and applicable for intraoperative image guidance during da Vinci robotic thoracic interventions using the proposed workflow. Tissue deformation and in vivo experiments are required before clinical evaluation of this system. PMID:25503592

Optimized 14 + 1 receive coil array and position system for 3D high-resolution MRI of dental and maxillomandibular structures.

PubMed

Sedlacik, Jan; Kutzner, Daniel; Khokale, Arun; Schulze, Dirk; Fiehler, Jens; Celik, Turgay; Gareis, Daniel; Smeets, Ralf; Friedrich, Reinhard E; Heiland, Max; Assaf, Alexandre T

2016-01-01

The purpose of this study was to design, build and test a multielement receive coil array and position system, which is optimized for three-dimensional (3D) high-resolution dental and maxillomandibular MRI with high patient comfort. A 14 + 1 coil array and positioning system, allowing easy handling by the technologists, reproducible positioning of the patients and high patient comfort, was tested with three healthy volunteers using a 3.0-T MRI machine (Siemens Skyra; Siemens Medical Solutions, Erlangen, Germany). High-resolution 3D T1 weighted, water excitation T1 weighted and fat-saturated T2 weighted imaging sequences were scanned, and 3D image data were reformatted in different orientations and curvatures to aid diagnosis. The high number of receiving coils and the comfortable positioning of the coil array close to the patient's face provided a high signal-to-noise ratio and allowed high quality, high resolution, 3D image data to be acquired within reasonable scan times owing to the possibility of parallel image acquisition acceleration. Reformatting the isotropic 3D image data in different views is helpful for diagnosis, e.g. panoramic reconstruction. The visibility of soft tissues such as the mandibular canal, nutritive canals and periodontal ligaments was exquisite. The optimized MRI receive coil array and positioning system for dental and oral-maxillofacial imaging provides a valuable tool for detecting and diagnosing pathologies in dental and oral-maxillofacial structures while avoiding radiation dose. The high patient comfort, as achieved by our design, is very crucial, since image artefacts due to movement or failing to complete the examination jeopardize the diagnostic value of MRI examinations.

Development of the Smart Weapons Operability Enhancement Interim Thermal Model

DTIC Science & Technology

1991-03-11

Absorptivity HFOL Vegetation Height (cm) (b.) hiveg.inp High Vegetation Parameters for VEGGIE 0.70 1.0 0.85 0.96 50.00 (c.) mnedveg.inp Medium Vegetation...Parameters for VEGGIE 0.40 1.0 0.85 0.96 100.00 (d.) grass.inp Grassland Parameters for VEGGIE 0.50 1.0 0.98 0.80 50.00 66 Table B-8. Input Records in

Results from Operational Testing of the Siemens Smart Grid-Capable Electric Vehicle Supply Equipment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bennett, Brion

2015-05-01

The Idaho National Laboratory conducted testing and analysis of the Siemens smart grid capable electric vehicle supply equipment (EVSE), which was a deliverable from Siemens for the U.S. Department of Energy FOA-554. The Idaho National Laboratory has extensive knowledge and experience in testing advanced conductive and wireless charging systems though INL’s support of the U.S. Department of Energy’s Advanced Vehicle Testing Activity. This document details the findings from the EVSE operational testing conducted at the Idaho National Laboratory on the Siemens smart grid capable EVSE. The testing conducted on the EVSE included energy efficiency testing, SAE J1772 functionality testing, abnormalmore » conditions testing, and charging of a plug-in vehicle.« less

Glycosidases induced in Aspergillus tamarii. Mycelial alpha-D-galactosidases.

PubMed Central

Civas, A; Eberhard, R; Le Dizet, P; Petek, F

1984-01-01

Two alpha-D-galactosidases (alpha-D-galactoside galactohydrolase, EC 3.2.1.22) produced by Aspergillus tamarii were purified from the mycelial extract by a procedure including chromatography on hydroxyapatite, DEAE-cellulose and ECTEOLA-cellulose. Each of these enzymes showed a single protein band corresponding to the alpha-D-galactosidase activity when examined by polyacrylamide-gel electrophoresis. They catalysed the hydrolysis of o-nitrophenyl alpha-D-galactoside, melibiose, raffinose and stachyose, but did not attack the galactomannans. Their Mr values were respectively 265000 +/- 5000 and 254000 +/- 5000 by the method of Hedrick & Smith [(1968) Arch. Biochem. Biophys. 126, 155-164]. Polyacrylamide-gel electrophoresis in the presence of sodium dodecyl sulphate in each case showed a single protein band, with Mr 88000 and 77500 respectively. The purified enzymes contained carbohydrate, consisting of N-acetylglucosamine, mannose, glucose and galactose in the estimated molar proportions of 1:9:5:8 in alpha-galactosidase I. Images Fig. 1. PMID:6331398

Meteoroid and debris special investigation group data acquisition procedures

NASA Technical Reports Server (NTRS)

See, Thomas H.; Allbrooks, Martha K.; Atkinson, Dale R.; Sapp, Clyde A.; Simon, Charles G.; Zolensky, Mike E.

1992-01-01

The entire LDEF spacecraft was examined by M&D SIG for impact (i.e., craters greater than or = 0.5 mm and penetrations greater than or = 0.3 mm in diameter) and related features (e.g., debris, secondaries). During the various detailed surveys conducted at NASA Kennedy, approx. 5,000 impact related features were photodocumented, and their locations measured and recorded; an additional approx. 30,000 smaller features were counted. The equipment and techniques used by the M&D SIG permitted the determination and recording of the locations and diameters of the 5,000 imaged features. A variety of experimental and LDEF structural hardware was acquired by the M&D SIG and is presently being examined and curated at NASA Johnson.

Surface decoration of red blood cells with maleimidophenyl-polyethylene glycol facilitated by thiolation with iminothiolane: an approach to mask A, B, and D antigens to generate universal red blood cells.

PubMed

Nacharaju, Parimala; Boctor, Fouad N; Manjula, Belur N; Acharya, Seetharama A

2005-03-01

The surface decoration of red blood cells (RBCs) by polyethylene glycol (PEG) chains has been an approach developed to camouflage the blood group antigens from their antibodies. A PEGylation protocol, however, that can mask the antigens appropriately to inhibit the agglutination of RBCs with the respective antibodies is not available so far. A new approach for PEGylation of RBC membrane proteins has been designed with thiolation-mediated maleimide chemistry. The accessibility of the surface lysine residues of membrane proteins to bulky PEG reagents was increased by linking an extension arm carrying a thiol group. RBCs have been PEGylated by thiolation-mediated chemistry with maleimidophenyl-PEG (Mal-Phe-PEG) reagents of different chain lengths. Mal-Phe-PEG-5000 chains alone masked the most important antigens of the Rh system (C, c, E, e, and D) from their antibodies. The masking of the A and B antigens needed a combination of Mal-Phe-PEG-5000 and Mal-Phe-PEG-20000 chains to inhibit the agglutination of RBCs completely with anti-A or anti-B. Thiolation-mediated PEGylation of RBCs with Mal-Phe-PEG-5000 and Mal-Phe-PEG-20000 converts Group A Rh(D)+ and B Rh(D)+ RBCs into RBCs with serologic behavior comparable to Group O Rh(D)- RBCs that are considered as universal RBCs for transfusion.

Microgravity

NASA Image and Video Library

1998-06-16

Eddie Snell (standing), Post-Doctoral Fellow the National Research Council (NRC),and Marc Pusey of Marshall Space Flight Center (MSFC) use a reciprocal space mapping diffractometer for marcromolecular crystal quality studies. The diffractometer is used in mapping the structure of marcromolecules such as proteins to determine their structure and thus understand how they function with other proteins in the body. This is one of several analytical tools used on proteins crystalized on Earth and in space experiments. Photo credit: NASA/Marshall Space Flight Center (MSFC)

Peak broadening and peak shift pole figures investigations by STRESS-SPEC diffractometer at FRM II

NASA Astrophysics Data System (ADS)

Gan, W. M.; Randau, C.; Hofmann, M.; Brokmeier, H. G.; Mueller, M.; Schreyer, A.

2012-02-01

This paper studied for the first time peak intensity, peak position and FHWM pole figures with one time measurement at the neutron diffractometer STRESS-SPEC via in-situ tensile deformation on austenitic steel. Fibre distribution with its evolution from central tensile direction to normal direction of these three kinds of pole figures was obtained. Variation of peak position and FWHM can be correlated to the reorientation of the texture component.

Water Vulnerability Assessments

DTIC Science & Technology

1991-04-01

Air Force Base , Texas 78235-5000 B AApril 1991 MAY f2-D T Final ReportBo R ’V Approved for public release...dilstribution Is unlimited. 91-00493 91 524 020 IIlI 111III II AIR FORCE SYSTEMS COMMAND SBROOKS AIR FORCE BASE , TEXAS 78235-5000 NOTICES When Government...tornadoes. If the base is on a fault line, they should do an assessment for earthquakes. Air Force plans should include sabotage, biological,

49 CFR Appendix B to Part 215 - Schedule of Civil Penalties 1

Code of Federal Regulations, 2014 CFR

2014-10-01

... 7,500 (d) Wheel rim, flange plate hub width: (1) Crack of less than 1″ 2,500 5,000 (2) Crack of 1... 215.13Pre-departure inspection 2,000 4,000 Subpart B—Freight Car Components: 215.103Defective wheel...) Gouge in surface that is between the wheel seats and is more than 1/8″ in depth 2,500 5,000 (c) End...

49 CFR Appendix B to Part 215 - Schedule of Civil Penalties 1

Code of Federal Regulations, 2013 CFR

2013-10-01

... 7,500 (d) Wheel rim, flange plate hub width: (1) Crack of less than 1″ 2,500 5,000 (2) Crack of 1... 215.13Pre-departure inspection 2,000 4,000 Subpart B—Freight Car Components: 215.103Defective wheel...) Gouge in surface that is between the wheel seats and is more than 1/8″ in depth 2,500 5,000 (c) End...

49 CFR Appendix B to Part 215 - Schedule of Civil Penalties 1

Code of Federal Regulations, 2011 CFR

2011-10-01

... 7,500 (d) Wheel rim, flange plate hub width: (1) Crack of less than 1″ 2,500 5,000 (2) Crack of 1... 215.13Pre-departure inspection 2,000 4,000 Subpart B—Freight Car Components: 215.103Defective wheel...) Gouge in surface that is between the wheel seats and is more than 1/8″ in depth 2,500 5,000 (c) End...

49 CFR Appendix B to Part 215 - Schedule of Civil Penalties 1

Code of Federal Regulations, 2012 CFR

2012-10-01

... 7,500 (d) Wheel rim, flange plate hub width: (1) Crack of less than 1″ 2,500 5,000 (2) Crack of 1... 215.13Pre-departure inspection 2,000 4,000 Subpart B—Freight Car Components: 215.103Defective wheel...) Gouge in surface that is between the wheel seats and is more than 1/8″ in depth 2,500 5,000 (c) End...

49 CFR Appendix B to Part 215 - Schedule of Civil Penalties 1

Code of Federal Regulations, 2010 CFR

2010-10-01

... 7,500 (d) Wheel rim, flange plate hub width: (1) Crack of less than 1″ 2,500 5,000 (2) Crack of 1... 215.13Pre-departure inspection 2,000 4,000 Subpart B—Freight Car Components: 215.103Defective wheel...) Gouge in surface that is between the wheel seats and is more than 1/8″ in depth 2,500 5,000 (c) End...

POWTEX Neutron Diffractometer at FRM II - New Perspectives for In-Situ Rock Deformation Analysis

NASA Astrophysics Data System (ADS)

Walter, J. M.; Stipp, M.; Ullemeyer, K.; Klein, H.; Leiss, B.; Hansen, B. T.; Kuhs, W. F.

2012-04-01

In Geoscience quantitative texture analysis here defined as the quantitative analysis of the crystallographic preferred orientation (CPO), is a common tool for the investigation of fabric development in mono- and polyphase rocks, their deformation histories and kinematics. Bulk texture measurements also allow the quantitative characterisation of the anisotropic physical properties of rock materials. A routine tool to measure bulk sample volumes is neutron texture diffraction, as neutrons have large penetration capabilities of several cm in geological sample materials. The new POWTEX (POWder and TEXture) Diffractometer at the neutron research reactor FRM II in Garching, Germany is designed as a high-intensity diffractometer by groups from the RWTH Aachen, Forschungszentrum Jülich and the University of Göttingen. Complementary to existing neutron diffractometers (SKAT at Dubna, Russia; GEM at ISIS, UK; HIPPO at Los Alamos, USA; D20 at ILL, France; and the local STRESS-SPEC and SPODI at FRM II) the layout of POWTEX is focused on fast time-resolved experiments and the measurement of larger sample series as necessary for the study of large scale geological structures. POWTEX is a dedicated beam line for geoscientific research. Effective texture measurements without sample tilting and rotation are possible firstly by utilizing a range of neutron wavelengths simultaneously (Time-of-Flight technique) and secondly by the high detector coverage (9.8 sr) and a high flux (~1 - 107 n/cm2s) at the sample. Furthermore the instrument and the angular detector resolution is designed also for strong recrystallisation textures as well as for weak textures of polyphase rocks. These instrument characteristics allow in-situ time-resolved texture measurements during deformation experiments on rocksalt, ice and other materials as large sample environments will be implemented at POWTEX. The in-situ deformation apparatus is operated by a uniaxial spindle drive with a maximum axial load of 250 kN, which will be redesigned to minimize shadowing effects inside the cylindrical detector. The HT deformatione experiments will be carried out in uniaxial compression or extension and an upgrade to triaxial deformation conditions is envisaged. The load frame can alternatively be used for ice deformation by inserting a cryostat cell for temperatures down to 77 K with a triaxial apparatus allowing also simple shear experiments on ice. Strain rates range between 10-8 and 10-3 s-1 reaching to at least 50 % axial strain. The deformation apparatus is designed for continuous long-term deformation experiments and can be exchanged between in-situ and ex-situ placements during continuous operation inside and outside the neutron detector.

Helical 4D CT and Comparison with Cine 4D CT

NASA Astrophysics Data System (ADS)

Pan, Tinsu

4D CT was one of the most important developments in radiation oncology in the last decade. Its early development in single slice CT and commercialization in multi-slice CT has radically changed our practice in radiation treatment of lung cancer, and has enabled the stereotactic radiosurgery of early stage lung cancer. In this chapter, we will document the history of 4D CT development, detail the data sufficiency condition governing the 4D CT data collection; present the design of the commercial helical 4D CTs from Philips and Siemens; compare the differences between the helical 4D CT and the GE cine 4D CT in data acquisition, slice thickness, acquisition time and work flow; review the respiratory monitoring devices; and understand the causes of image artifacts in 4D CT.

Neutron diffraction from aligned stacks of lipid bilayers using the WAND instrument

DOE PAGES

Marquardt, Drew; Frontzek, Matthias D.; Zhao, Yu; ...

2018-02-06

Neutron diffraction from aligned stacks of lipid bilayers is examined using the Wide-Angle Neutron Diffractometer (WAND), located at the High Flux Isotope Reactor, Oak Ridge, Tennessee, USA. Data were collected at different levels of hydration and neutron contrast by varying the relative humidity (RH) and H 2O/D 2O ratio from multi-bilayers of dioleoylphosphatidylcholine and sunflower phosphatidylcholine extract aligned on single-crystal silicon substrates. This work highlights the capabilites of a newly fabricated sample hydration cell, which allows the lipid bilayers to be hydrated with varying H/D ratios from the RH generated by saturated salt solutions, and also demonstrates WAND's capability asmore » an instrument suitable for the study of aligned lipid multi-bilayers.« less

Neutron diffraction from aligned stacks of lipid bilayers using the WAND instrument

DOE Office of Scientific and Technical Information (OSTI.GOV)

Marquardt, Drew; Frontzek, Matthias D.; Zhao, Yu

Neutron diffraction from aligned stacks of lipid bilayers is examined using the Wide-Angle Neutron Diffractometer (WAND), located at the High Flux Isotope Reactor, Oak Ridge, Tennessee, USA. Data were collected at different levels of hydration and neutron contrast by varying the relative humidity (RH) and H 2O/D 2O ratio from multi-bilayers of dioleoylphosphatidylcholine and sunflower phosphatidylcholine extract aligned on single-crystal silicon substrates. This work highlights the capabilites of a newly fabricated sample hydration cell, which allows the lipid bilayers to be hydrated with varying H/D ratios from the RH generated by saturated salt solutions, and also demonstrates WAND's capability asmore » an instrument suitable for the study of aligned lipid multi-bilayers.« less

Leonardo da Vinci's drapery studies: characterization of lead white pigments by µ-XRD and 2D scanning XRF

NASA Astrophysics Data System (ADS)

Gonzalez, Victor; Calligaro, Thomas; Pichon, Laurent; Wallez, Gilles; Mottin, Bruno

2015-11-01

This work focuses on the composition and microstructure of the lead white pigment employed in a set of paintworks, using a combination of µ-XRD and 2D scanning XRF, directly applied on five drapery studies attributed to Leonardo da Vinci (1452-1519) and conserved in the Département des Arts Graphiques, Musée du Louvre and in the Musée des Beaux- Arts de Rennes. Trace elements present in the composition as well as in the lead white highlights were imaged by 2D scanning XRF. Mineral phases were determined in a fully noninvasive way using a special µ-XRD diffractometer. Phase proportions were estimated by Rietveld refinement. The analytical results obtained will contribute to differentiate lead white qualities and to highlight the artist's technique.

Protein Crystal Quality Studies

NASA Technical Reports Server (NTRS)

1998-01-01

Eddie Snell (standing), Post-Doctoral Fellow the National Research Council (NRC),and Marc Pusey of Marshall Space Flight Center (MSFC) use a reciprocal space mapping diffractometer for marcromolecular crystal quality studies. The diffractometer is used in mapping the structure of marcromolecules such as proteins to determine their structure and thus understand how they function with other proteins in the body. This is one of several analytical tools used on proteins crystalized on Earth and in space experiments. Photo credit: NASA/Marshall Space Flight Center (MSFC)

Thermal stabilization of neutron Larmor diffractometers

NASA Astrophysics Data System (ADS)

Keller, T.; Tralmer, F.

2017-06-01

We report on the design of a support unit for the radio frequency (RF) coils of a Larmor diffractometer (LD) eliminating fluctuations of the Larmor phase resulting from thermal expansion of the support structures. The key component defining the spacing between the RF coils is a Zerodur bar with a very low thermal expansion coefficient (α = 7 × 10-8 K-1). This support unit will allow for LD measurements on the 10-6 accuracy level even if the ambient temperature is fluctuating.

The CT image standardization based on the verified PSF

NASA Astrophysics Data System (ADS)

Wada, Shinichi; Ohkubo, Masaki; Kunii, Masayuki; Matsumoto, Toru; Murao, Kohei; Awai, Kazuo; Ikeda, Mitsuru

2007-03-01

This study discusses a method of CT image quality standardization that uses a point-spread function (PSF) in MDCT. CT image I(x,y,z) is represented by the following formula: I(x,y,z) = O(x,y,z)***PSF(x,y,z). Standardization was performed by measuring the three-dimensional (3-D) PSFs of two CT images with different image qualities. The image conversion method was constructed and tested using the 3-D PSFs and CT images of the CT scanners of three different manufacturers. The CT scanners used were Lightspeed QX/i, Somatom Volume Zoom, and Brilliance-40. To obtain the PSF(x,y) of these CT scanners, the line spread functions of the respective reconstruction kernels were measured using a phantom described by J.M. Boone. The kernels for each scanner were: soft, standard, lung, bone, and bone plus (GE); B20f, B40f, B41f, B50f, and B60f (Siemens); and B, C, D, E, and L (Philips). Slice sensitivity profile (SSP) were measured using a micro-disk phantom (50 μm* φ1 mm) with 5 mm slice thickness and beam pitch of 1.5 (GE, Siemens) and 0.626 (Philips). 3-D PSF was verified using an MDCT QA phantom. Real chest CT images were converted to images with contrasting standard image quality. Comparison between the converted CT image and the original standard image showed good agreement. The usefulness of the image conversion method is discussed using clinical CT images acquired by CT scanners produced by different manufacturers.

Multimode C-arm fluoroscopy, tomosynthesis, and cone-beam CT for image-guided interventions: from proof of principle to patient protocols

NASA Astrophysics Data System (ADS)

Siewerdsen, J. H.; Daly, M. J.; Bachar, G.; Moseley, D. J.; Bootsma, G.; Brock, K. K.; Ansell, S.; Wilson, G. A.; Chhabra, S.; Jaffray, D. A.; Irish, J. C.

2007-03-01

High-performance intraoperative imaging is essential to an ever-expanding scope of therapeutic procedures ranging from tumor surgery to interventional radiology. The need for precise visualization of bony and soft-tissue structures with minimal obstruction to the therapy setup presents challenges and opportunities in the development of novel imaging technologies specifically for image-guided procedures. Over the past ~5 years, a mobile C-arm has been modified in collaboration with Siemens Medical Solutions for 3D imaging. Based upon a Siemens PowerMobil, the device includes: a flat-panel detector (Varian PaxScan 4030CB); a motorized orbit; a system for geometric calibration; integration with real-time tracking and navigation (NDI Polaris); and a computer control system for multi-mode fluoroscopy, tomosynthesis, and cone-beam CT. Investigation of 3D imaging performance (noise-equivalent quanta), image quality (human observer studies), and image artifacts (scatter, truncation, and cone-beam artifacts) has driven the development of imaging techniques appropriate to a host of image-guided interventions. Multi-mode functionality presents a valuable spectrum of acquisition techniques: i.) fluoroscopy for real-time 2D guidance; ii.) limited-angle tomosynthesis for fast 3D imaging (e.g., ~10 sec acquisition of coronal slices containing the surgical target); and iii.) fully 3D cone-beam CT (e.g., ~30-60 sec acquisition providing bony and soft-tissue visualization across the field of view). Phantom and cadaver studies clearly indicate the potential for improved surgical performance - up to a factor of 2 increase in challenging surgical target excisions. The C-arm system is currently being deployed in patient protocols ranging from brachytherapy to chest, breast, spine, and head and neck surgery.

Design of an ultraprecision computerized numerical control chemical mechanical polishing machine and its implementation

NASA Astrophysics Data System (ADS)

Zhang, Chupeng; Zhao, Huiying; Zhu, Xueliang; Zhao, Shijie; Jiang, Chunye

2018-01-01

The chemical mechanical polishing (CMP) is a key process during the machining route of plane optics. To improve the polishing efficiency and accuracy, a CMP model and machine tool were developed. Based on the Preston equation and the axial run-out error measurement results of the m circles on the tin plate, a CMP model that could simulate the material removal at any point on the workpiece was presented. An analysis of the model indicated that lower axial run-out error led to lower material removal but better polishing efficiency and accuracy. Based on this conclusion, the CMP machine was designed, and the ultraprecision gas hydrostatic guideway and rotary table as well as the Siemens 840Dsl numerical control system were incorporated in the CMP machine. To verify the design principles of machine, a series of detection and machining experiments were conducted. The LK-G5000 laser sensor was employed for detecting the straightness error of the gas hydrostatic guideway and the axial run-out error of the gas hydrostatic rotary table. A 300-mm-diameter optic was chosen for the surface profile machining experiments performed to determine the CMP efficiency and accuracy.

Technical Note: Characterization of custom 3D printed multimodality imaging phantoms.

PubMed

Bieniosek, Matthew F; Lee, Brian J; Levin, Craig S

2015-10-01

Imaging phantoms are important tools for researchers and technicians, but they can be costly and difficult to customize. Three dimensional (3D) printing is a widely available rapid prototyping technique that enables the fabrication of objects with 3D computer generated geometries. It is ideal for quickly producing customized, low cost, multimodal, reusable imaging phantoms. This work validates the use of 3D printed phantoms by comparing CT and PET scans of a 3D printed phantom and a commercial "Micro Deluxe" phantom. This report also presents results from a customized 3D printed PET/MRI phantom, and a customized high resolution imaging phantom with sub-mm features. CT and PET scans of a 3D printed phantom and a commercial Micro Deluxe (Data Spectrum Corporation, USA) phantom with 1.2, 1.6, 2.4, 3.2, 4.0, and 4.8 mm diameter hot rods were acquired. The measured PET and CT rod sizes, activities, and attenuation coefficients were compared. A PET/MRI scan of a custom 3D printed phantom with hot and cold rods was performed, with photon attenuation and normalization measurements performed with a separate 3D printed normalization phantom. X-ray transmission scans of a customized two level high resolution 3D printed phantom with sub-mm features were also performed. Results show very good agreement between commercial and 3D printed micro deluxe phantoms with less than 3% difference in CT measured rod diameter, less than 5% difference in PET measured rod diameter, and a maximum of 6.2% difference in average rod activity from a 10 min, 333 kBq/ml (9 μCi/ml) Siemens Inveon (Siemens Healthcare, Germany) PET scan. In all cases, these differences were within the measurement uncertainties of our setups. PET/MRI scans successfully identified 3D printed hot and cold rods on PET and MRI modalities. X-ray projection images of a 3D printed high resolution phantom identified features as small as 350 μm wide. This work shows that 3D printed phantoms can be functionally equivalent to commercially available phantoms. They are a viable option for quickly distributing and fabricating low cost, customized phantoms.

A Survey of Commonly Applied Methods for Software Process Improvement

DTIC Science & Technology

1994-02-01

conducted a controlled experimental study of the effectiveness of the method. They compared 10 cleanroom teams with 5 non -cleanroom teams working for six...Robert D. Austin Doctoral Candidate Carnegie Mellon University Daniel J. Paulish Resident Affiliate Siemens Corporate Research , Inc. Accesion For0...the U.S. Department of Defense. Copyright 0 1994 by Carnegie Mellon University. Copies of the documen are available from Research Access. Iinc., 800

Designing of a technological line in the context of controlling with the use of integration of the virtual controller with the mechatronics concept designer module of the PLM Siemens NX software

NASA Astrophysics Data System (ADS)

Herbuś, K.; Ociepka, P.

2017-08-01

In the work is examined the sequential control system of a technological line in the form of the final part of a system of an internal transport. The process of designing this technological line using the computer-aided approach ran concurrently in two different program environments. In the Mechatronics Concept Designer module of the PLM Siemens NX software was developed the 3D model of the technological line prepared for verification the logic interrelations implemented in the control system. For this purpose, from the whole system of the technological line, it was distinguished the sub-system of actuators and sensors, because their correct operation determines the correct operation of the whole system. Whereas in the application of the virtual controller have been implemented the algorithms of work of the planned line. Then both program environments have been integrated using the OPC server, which enables the exchange of data between the considered systems. The data on the state of the object and the data defining the way and sequence of operation of the technological line are exchanged between the virtual controller and the 3D model of the technological line in real time.

Ganges Chasma in 3-D

NASA Image and Video Library

1999-06-25

Ganges Chasma is part of the Valles Marineris trough system that stretches nearly 5,000 kilometers 3,000 miles across the western equatorial region of Mars. This stereo anaglyph is from NASA Mars Global Surveyor. 3D glasses are necessary.

26 CFR 1.668(b)-2 - Illustration of the provisions of subpart D.

Code of Federal Regulations, 2010 CFR

2010-04-01

... distributable net income of the trust as determined under section 643(a) for 1954, 1955, 1956, and 1957 is...) Total 1954 $15,000 $20,000 $10,000 $5,000 $50,000 1955 10,000 15,000 10,000 5,000 40,000 1956 10,000 20... through 1957: A B 1954 $25,000 None 1955 20,000 None 1956 25,000 $45,000 1957 22,500 29,550 (b...

Non-Wovens as Sound Reducers

NASA Astrophysics Data System (ADS)

Belakova, D.; Seile, A.; Kukle, S.; Plamus, T.

2018-04-01

Within the present study, the effect of hemp (40 wt%) and polyactide (60 wt%), non-woven surface density, thickness and number of fibre web layers on the sound absorption coefficient and the sound transmission loss in the frequency range from 50 to 5000 Hz is analysed. The sound insulation properties of the experimental samples have been determined, compared to the ones in practical use, and the possible use of material has been defined. Non-woven materials are ideally suited for use in acoustic insulation products because the arrangement of fibres produces a porous material structure, which leads to a greater interaction between sound waves and fibre structure. Of all the tested samples (A, B and D), the non-woven variant B exceeded the surface density of sample A by 1.22 times and 1.15 times that of sample D. By placing non-wovens one above the other in 2 layers, it is possible to increase the absorption coefficient of the material, which depending on the frequency corresponds to C, D, and E sound absorption classes. Sample A demonstrates the best sound absorption of all the three samples in the frequency range from 250 to 2000 Hz. In the test frequency range from 50 to 5000 Hz, the sound transmission loss varies from 0.76 (Sample D at 63 Hz) to 3.90 (Sample B at 5000 Hz).

Double Filtration Plasma Apheresis Shortens Hospital Admission Duration of Patients With Severe Hypertriglyceridemia-Associated Acute Pancreatitis.

PubMed

Chang, Chiz-Tzung; Tsai, Tsung-Yu; Liao, Hsin-Yi; Chang, Chia-Ming; Jheng, Jyun-Shan; Huang, Wen-Hsin; Chou, Che-Yi; Chen, Chao-Jung

2016-04-01

The treatment effectiveness of double filtration plasma apheresis (DFPP) on severe hypertriglyceridemia-associated acute pancreatitis (STAP) has been questioned because the currently defined serum triglyceride level--1000 mg/dL--is too low for STAP. Given this, we aimed to investigate DFPP effectiveness when we elevated STAP definition to 5000 mg/dL serum triglyceride. We performed nested case-control studies for STAP patients and divided them into groups "with" or "without" DFPP. We further recruited outpatient asymptomatic hypertriglyceridemia patients with STAP history, then divided them into groups "with" or "without" prophylactic DFPP once every 3 to 6 months for 2 years. We observed hospitalization duration and STAP recurrence between patients with and patients without DFPP. Twelve STAP patients receiving DFPP had a median hospitalization of 5 days, whereas 24 patients without DFPP had 10 days (P = 0.009). Six outpatient referrals with STAP history receiving prophylactic DFPP showed no STAP recurrences whereas 6 without DFPP showed 3 recurrences (P = 0.046). For the 25 patients whose serum triglyceride exceeded 5000 mg/dL, 11 receiving DFPP had median hospitalization of 5 days while 14 without DFPP had 11 days (P = 0.012). When applied to serum triglyceride in excess of 5000 mg/dL, DFPP removes oxidized and inflammatory lipoproteins, shortens hospitalization duration, and minimizes STAP recurrence.

Should Project Managers Buy Technical Data

DTIC Science & Technology

2017-04-06

Should Project Managers Buy Technical Data? Jerry Harper April 6, 2017 PUBLISHED BY The Defense...intellectual property (IP) management and technical data rights (TDR) strategies. According to DoD Instruction 5000.02 (DoD, 2017), project managers (PMs...Defense Authorization Act NDI ................nondevelopmental item PM ................. project manager R&D ...............research and development

Siemens, Philips megaproject to yield superchip in 5 years

NASA Astrophysics Data System (ADS)

1985-02-01

The development of computer chips using complementary metal oxide semiconductor (CMOS) memory technology is described. The management planning and marketing strategy of the Philips and Siemens corporations with regard to the memory chip are discussed.

TH-AB-207A-09: Tailoring TCM Schemes to a Task: Evaluating the Impact of Customized TCM Profiles On Detection of Lung Nodules in Simulated CT Lung Cancer Screening

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hoffman, J; McNitt-Gray, M; Noo, F

Purpose: Recent work has shown that current TCM profile designs boost detection of low-contrast lung lesions in the lung apices, but yield reduced detection performance in the mid and lower lung regions relative to fixed tube current cases. This observed imbalance suggests that the TCM scheme might be tailored in new ways to maximize nodule detection throughout the entire lung. In this work, we begin a preliminary investigation into custom TCM profiles in an attempt to achieve uniform lesion detection throughout the extent of the lung. Methods: Low-contrast (25HU), 6mm nodules representing ground glass opacities were simulated at 1mm intervalsmore » over the length the lungs in a voxelized model of the XCAT phantom, one nodule per lung, per simulated scan. Voxel values represented attenuation values at 80keV. CT projection data was created by simulating a finite focal spot and using Joseph’s method for forward projection; scanner geometry was that of the Siemens Sensation 64 and the X-ray source was simulated as an 80keV monochromatic beam. Noise realizations were created using Poisson statistics, a realistic bowtie filter and varying tube current. 500 noise realizations were created for the custom TCM designs. All reconstruction was done with FreeCT-wFBP. An SKE/BKE task was used in conjunction with a 2D Hotelling Observer to calculate area-under-the-curve (AUC) as a proxy for “detectability.” AUC was plotted as a function of nodule Z-location to create a “detectability map.” The detectability map for the custom TCM curve was qualitatively assessed relative to previous results for the fixed TC and clinical TCM cases for uniformity. Results: Detection uniformity was improved throughout the mid and lower lungs, however detection remained disproportionately high in the upper lung region. Conclusion: Detection uniformity was improved with a custom TC profile. Future work will incorporate an analytic, task-specific approach to optimize the TC scheme for nodule detection. J. Hoffman: Part-time intern, Toshiba Medical Research Institute; M. McNitt-Gray: Institutional research agreement, Siemens Healthcare; Past recipient, research grant support, Siemens Healthcare; Consultant, Toshiba America Medical Systems; Consultant, Samsung Electronics; F. Noo: Institutional research agreement, Siemens Healthcare; Receives research funding from Siemens Healthcare.« less

49 CFR Appendix B to Part 229 - Schedule of Civil Penalties 1

Code of Federal Regulations, 2012 CFR

2012-10-01

... 1,000 2,000 (f) Replace Form FRA F 6180.49A by April 2 or July 3 (g) Secondary record of the... 229.75Wheel and tire defects: (a),(d) Slid flat or shelled spot(s): (1) One spot 21/2″ or more but less than 3″ in length 2,500 5,000 (2) One spot 3″ or more in length 5,000 7,500 (3) Two adjoining...

49 CFR Appendix B to Part 229 - Schedule of Civil Penalties 1

Code of Federal Regulations, 2014 CFR

2014-10-01

... 1,000 2,000 (f) Replace Form FRA F 6180.49A by April 2 or July 3 (g) Secondary record of the... 229.75Wheel and tire defects: (a),(d) Slid flat or shelled spot(s): (1) One spot 21/2″ or more but less than 3″ in length 2,500 5,000 (2) One spot 3″ or more in length 5,000 7,500 (3) Two adjoining...

49 CFR Appendix B to Part 229 - Schedule of Civil Penalties 1

Code of Federal Regulations, 2013 CFR

2013-10-01

... 1,000 2,000 (f) Replace Form FRA F 6180.49A by April 2 or July 3 (g) Secondary record of the... 229.75Wheel and tire defects: (a),(d) Slid flat or shelled spot(s): (1) One spot 21/2″ or more but less than 3″ in length 2,500 5,000 (2) One spot 3″ or more in length 5,000 7,500 (3) Two adjoining...

Rotatable multifunctional load frames for neutron diffractometers at FRM II—design, specifications and applications

NASA Astrophysics Data System (ADS)

Hoelzel, M.; Gan, W. M.; Hofmann, M.; Randau, C.; Seidl, G.; Jüttner, Ph.; Schmahl, W. W.

2013-05-01

Novel tensile rigs have been designed and manufactured at the research reactor Heinz Maier-Leibnitz (FRM II, Garching near Munich). Besides tensile and compressive stress, also torsion can be applied. The unique Eulerian cradle type design (ω, χ, and φ axis) allows orienting the stress axis with respect to the scattering vector. Applications of these tensile rigs at our neutron diffractometers enable various investigations of structural changes under mechanical load, e.g. crystallographic texture evolution, stress-induced phase transformations or lattice expansion, and the anisotropy of mechanical response.

Mineralogical Results from the Mars Science Laboratory Rover Curiosity

NASA Technical Reports Server (NTRS)

Blake, David Frederick.

2017-01-01

NASA's CheMin instrument, the first X-ray Diffractometer flown in space, has been operating on Mars for nearly five years. CheMin was first to establish the quantitative mineralogy of the Mars global soil (1). The instrument was next used to determine the mineralogy of a 3.7 billion year old lacustrine mudstone, a result that, together with findings from other instruments on the MSL Curiosity rover, documented the first habitable environment found on another planet (2). The mineralogy of this mudstone from an ancient playa lake was also used to derive the maximum concentration of CO2 in the early Mars atmosphere, a surprisingly low value that calls into question the current theory that CO2 greenhouse warming was responsible for the warm and wet environment of early Mars. CheMin later identified the mineral tridymite, indicative of silica-rich volcanism, in mudstones of the Murray formation on Mt. Sharp. This discovery challenges the paradigm of Mars as a basaltic planet and ushers in a new chapter of comparative terrestrial planetology (3). CheMin is now being used to systematically sample the sedimentary layers that comprise the lower strata of Mt. Sharp, a 5,000 meter sequence of sedimentary rock laid down in what was once a crater lake, characterizing isochemical sediments that through their changing mineralogy, document the oxidation and drying out of the Mars in early Hesperian time.

[Haemolysis and turbidity influence on three analysis methods of quantitative determination of total and conjugated bilirubin on ADVIA 1650].

PubMed

Gobert De Paepe, E; Munteanu, G; Schischmanoff, P O; Porquet, D

2008-01-01

Plasma bilirubin testing is crucial to prevent the occurrence of neonatal kernicterus. Haemolysis may occur during sampling and interfere with bilirubin determination. Moreover, lipidic infusions may induce plasma lipemia and also interfere with bilirubin measurement. We evaluated the interference of haemolysis and lipemia with three methods of total and direct bilirubin measurement adaptated on an Advia 1650 analyser (Siemens Medical Solutions Diagnostics) : Synermed (Sofibel), Bilirubin 2 (Siemens) and Bilirubin Auto FS (Diasys). The measurement of total bilirubin was little affected by haemolysis with all three methods. The Bilirubin 2 (Siemens) method was the less sensitive to haemolysis even at low bilirubin levels. The measurement of conjugated bilirubin was significantly altered by low heamoglobin concentrations for Bilirubin Auto FS(R) (30 microM or 0,192 g/100 mL haemoglobin) and for Synermed (60 microM or 0,484 g/100 mL haemoglobin). In marked contrast, we found no haemoglobin interference with the Direct Bilirubin 2 reagent which complied with the method validation criteria from the French Society for Biological Chemistry. The lipemia up to 2 g/L of Ivelip did not affect neither the measurement of total bilirubin for all three methods nor the measurement of conjugated bilirubin with the Diasys and Siemens reagents. However, we observed a strong interference starting at 0,5 g/L of Ivelip with the Synermed reagent. Our data suggest that both Siemens and Diasys methods allow to measure accurately total and conjugated bilirubin in hemolytic and lipemic samples, nevertheless, the Siemens methodology is less affected by these interferences.

Quantitative phase analysis of challenging samples using neutron powder diffraction. Sample #4 from the CPD QPA round robin revisited

DOE PAGES

Whitfield, Pamela S.

2016-04-29

Here, quantitative phase analysis (QPA) using neutron powder diffraction more often than not involves non-ambient studies where no sample preparation is possible. The larger samples and penetration of neutrons versus X-rays makes neutron diffraction less susceptible to inhomogeneity and large grain sizes, but most well-characterized QPA standard samples do not have these characteristics. Sample #4 from the International Union of Crystallography Commission on Powder Diffraction QPA round robin was one such sample. Data were collected using the POWGEN time-of-flight (TOF) neutron powder diffractometer and analysed together with historical data from the C2 diffractometer at Chalk River. The presence of magneticmore » reflections from Fe 3O 4 (magnetite) in the sample was an additional consideration, and given the frequency at which iron-containing and other magnetic compounds are present during in-operando studies their possible impact on the accuracy of QPA is of interest. Additionally, scattering from thermal diffuse scattering in the high-Qregion (<0.6 Å) accessible with TOF data could impact QPA results during least-squares because of the extreme peak overlaps present in this region. Refinement of POWGEN data was largely insensitive to the modification of longer d-spacing reflections by magnetic contributions, but the constant-wavelength data were adversely impacted if the magnetic structure was not included. A robust refinement weighting was found to be effective in reducing quantification errors using the constant-wavelength neutron data both where intensities from magnetic reflections were ignored and included. Results from the TOF data were very sensitive to inadequate modelling of the high- Q (low d-spacing) background using simple polynomials.« less

Near East/South Asia Report

DTIC Science & Technology

1986-10-27

MAN), Siemens and Kraftwerk Union (KIW), all of West Germany; South Korea’s Samsung Corporation; Mitsubishi Heavy Industries and Marubeni...Gruppo Industrie Elettro~ meccaniche per Impianti all’Estero (GIE), and Switzerland’s BBC Brown. Boveri & Company, Kraftwerk Union and Siemens, both

Comparative power law analysis of structured breast phantom and patient images in digital mammography and breast tomosynthesis.

PubMed

Cockmartin, L; Bosmans, H; Marshall, N W

2013-08-01

This work characterizes three candidate mammography phantoms with structured background in terms of power law analysis in the low frequency region of the power spectrum for 2D (planar) mammography and digital breast tomosynthesis (DBT). The study was performed using three phantoms (spheres in water, Voxmam, and BR3D CIRS phantoms) on two DBT systems from two different vendors (Siemens Inspiration and Hologic Selenia Dimensions). Power spectra (PS) were calculated for planar projection, DBT projection, and reconstructed images and curve fitted in the low frequency region from 0.2 to 0.7 mm(-1) with a power law function characterized by an exponent β and magnitude κ. The influence of acquisition dose and tube voltage on the power law parameters was first explored. Then power law parameters were calculated from images acquired with the same anode∕filter combination and tube voltage for the three test objects, and compared with each other. Finally, PS curves for automatic exposure controlled acquisitions (anode∕filter combination and tube voltages selected by the systems based on the breast equivalent thickness of the test objects) were compared against PS analysis performed on patient data (for Siemens 80 and for Hologic 48 mammograms and DBT series). Dosimetric aspects of the three test objects were also examined. The power law exponent (β) was found to be independent of acquisition dose for planar mammography but varied more for DBT projections of the sphere-phantom. Systematic increase of tube voltage did not affect β but decreased κ, both in planar and DBT projection phantom images. Power spectra of the BR3D phantom were closer to those of the patients than these of the Voxmam phantom; the Voxmam phantom gave high values of κ compared to the other phantoms and the patient series. The magnitude of the PS curves of the BR3D phantom was within the patient range but β was lower than the average patient value. Finally, PS magnitude for the sphere-phantom coincided with the patient curves for Siemens but was lower for the Hologic system. Close agreement of doses for all three phantoms with patient doses was found. Power law parameters of the phantoms were close to those of the patients but no single phantom matched in terms of both magnitude (κ) and texture (β) for the x-ray systems in this work. PS analysis of structured phantoms is feasible and this methodology can be used to suggest improvements in phantom design.

Proceedings of Annual Acquisition Research Symposium (7th), Hershey, Pennsylvania, 31 May-2 Jun 1978

DTIC Science & Technology

1978-06-01

strongly, with DCS/Plans our efforts going during difficult periods, and Operation leadership and heavy MAJCOM but mission area planning and analysis is...implementing DOD required with heavy participation by AFSC. Directives 5000.1 and 5000.2 require new pro- Zero-Base Budgeting is the third part of the...Mission Area Analysis portion, it it -omposed of three logical steps. The fir-t .?p de - velops viable alternatives for tae -.. R&D programs. The second

Comparison of reconstruction methods and quantitative accuracy in Siemens Inveon PET scanner

NASA Astrophysics Data System (ADS)

Ram Yu, A.; Kim, Jin Su; Kang, Joo Hyun; Moo Lim, Sang

2015-04-01

PET reconstruction is key to the quantification of PET data. To our knowledge, no comparative study of reconstruction methods has been performed to date. In this study, we compared reconstruction methods with various filters in terms of their spatial resolution, non-uniformities (NU), recovery coefficients (RCs), and spillover ratios (SORs). In addition, the linearity of reconstructed radioactivity between linearity of measured and true concentrations were also assessed. A Siemens Inveon PET scanner was used in this study. Spatial resolution was measured with NEMA standard by using a 1 mm3 sized 18F point source. Image quality was assessed in terms of NU, RC and SOR. To measure the effect of reconstruction algorithms and filters, data was reconstructed using FBP, 3D reprojection algorithm (3DRP), ordered subset expectation maximization 2D (OSEM 2D), and maximum a posteriori (MAP) with various filters or smoothing factors (β). To assess the linearity of reconstructed radioactivity, image quality phantom filled with 18F was used using FBP, OSEM and MAP (β =1.5 & 5 × 10-5). The highest achievable volumetric resolution was 2.31 mm3 and the highest RCs were obtained when OSEM 2D was used. SOR was 4.87% for air and 3.97% for water, obtained OSEM 2D reconstruction was used. The measured radioactivity of reconstruction image was proportional to the injected one for radioactivity below 16 MBq/ml when FBP or OSEM 2D reconstruction methods were used. By contrast, when the MAP reconstruction method was used, activity of reconstruction image increased proportionally, regardless of the amount of injected radioactivity. When OSEM 2D or FBP were used, the measured radioactivity concentration was reduced by 53% compared with true injected radioactivity for radioactivity <16 MBq/ml. The OSEM 2D reconstruction method provides the highest achievable volumetric resolution and highest RC among all the tested methods and yields a linear relation between the measured and true concentrations for radioactivity Our data collectively showed that OSEM 2D reconstruction method provides quantitatively accurate reconstructed PET data results.

Steam Turbine Materials for Ultrasupercritical Coal Power Plants

DOE Office of Scientific and Technical Information (OSTI.GOV)

Viswanathan, R.; Hawk, J.; Schwant, R.

The Ultrasupercritical (USC) Steam Turbine Materials Development Program is sponsored and funded by the U.S. Department of Energy and the Ohio Coal Development Office, through grants to Energy Industries of Ohio (EIO), a non-profit organization contracted to manage and direct the project. The program is co-funded by the General Electric Company, Alstom Power, Siemens Power Generation (formerly Siemens Westinghouse), and the Electric Power Research Institute, each organization having subcontracted with EIO and contributing teams of personnel to perform the requisite research. The program is focused on identifying, evaluating, and qualifying advanced alloys for utilization in coal-fired power plants that needmore » to withstand steam turbine operating conditions up to 760°C (1400°F) and 35 MPa (5000 psi). For these conditions, components exposed to the highest temperatures and stresses will need to be constructed from nickel-based alloys with higher elevated temperature strength than the highchromium ferritic steels currently used in today's high-temperature steam turbines. In addition to the strength requirements, these alloys must also be weldable and resistant to environmental effects such as steam oxidation and solid particle erosion. In the present project, candidate materials with the required creep strength at desired temperatures have been identified. Coatings that can resist oxidation and solid particle erosion have also been identified. The ability to perform dissimilar welds between nickel base alloys and ferritic steels have been demonstrated, and the properties of the welds have been evaluated. Results of this three-year study that was completed in 2009 are described in this final report. Additional work is being planned and will commence in 2009. The specific objectives of the future studies will include conducting more detailed evaluations of the weld-ability, mechanical properties and repair-ability of the selected candidate alloys for rotors, casings and valves, and to perform scale-up studies to establish a design basis for commercial scale components. A supplemental program funded by the Ohio Coal Development Office will undertake supporting tasks such as testing and trials using existing atmospheric, vacuum and developmental pressure furnaces to define specific metal casting techniques needed for producing commercial scale components.« less

Electrical, optical and structural properties of transparent conducting Al doped ZnO (AZO) deposited by sol-gel spin coating

NASA Astrophysics Data System (ADS)

Tonny, Kaniz Naila; Rafique, Rosaleena; Sharmin, Afrina; Bashar, Muhammad Shahriar; Mahmood, Zahid Hasan

2018-06-01

Al doped ZnO (AZO) films are fabricated by using sol-gel spin coating method and changes in electrical, optical and structural properties due to variation in film thickness is studied. AZO films provide c-axis orientation along the (002) plane and peak sharpness increased with film thickness is evident from XRD analysis. Conductivity (σ) of AZO films has increased from 2.34 (Siemens/cm) to 20156.27 (Siemens/cm) whereas sheet resistance (Rsh) decreases from 606300 (ohms/sq.) to 2.08 (ohm/sq.) with increase of film thickness from 296 nm to 1030 nm. Optical transmittance (T%) of AZO films is decreased from around 82% to 62% in the visible region. And grain size (D) of AZO thin films has been found to increase from 19.59 nm to 25.25 nm with increase of film thickness. Figure of Merit is also calculated for prepared sample of AZO. Among these four sample of AZO thin films, L-15 sample (having thickness in 895 nm) has provided highest figure of merit which is 5.49*10^-4 (Ω-1).

Comparison of different approaches of estimating effective dose from reported exposure data in 3D imaging with interventional fluoroscopy systems

NASA Astrophysics Data System (ADS)

Svalkvist, Angelica; Hansson, Jonny; Bâth, Magnus

2014-03-01

Three-dimensional (3D) imaging with interventional fluoroscopy systems is today a common examination. The examination includes acquisition of two-dimensional projection images, used to reconstruct section images of the patient. The aim of the present study was to investigate the difference in resulting effective dose obtained using different levels of complexity in calculations of effective doses from these examinations. In the study the Siemens Artis Zeego interventional fluoroscopy system (Siemens Medical Solutions, Erlangen, Germany) was used. Images of anthropomorphic chest and pelvis phantoms were acquired. The exposure values obtained were used to calculate the resulting effective doses from the examinations, using the computer software PCXMC (STUK, Helsinki, Finland). The dose calculations were performed using three different methods: 1. using individual exposure values for each projection image, 2. using the mean tube voltage and the total DAP value, evenly distributed over the projection images, and 3. using the mean kV and the total DAP value, evenly distributed over smaller selection of projection images. The results revealed that the difference in resulting effective dose between the first two methods was smaller than 5%. When only a selection of projection images were used in the dose calculations the difference increased to over 10%. Given the uncertainties associated with the effective dose concept, the results indicate that dose calculations based on average exposure values distributed over a smaller selection of projection angles can provide reasonably accurate estimations of the radiation doses from 3D imaging using interventional fluoroscopy systems.

A Model for Evaluating Tactually Assistive Devices.

ERIC Educational Resources Information Center

Terrio, Lee; Haas, William

1986-01-01

Audiometric instruments and techniques adopted to measure tactual cueing characteristics of the Radioear B70A and the Siemens Fonator electromechanical vibrators were used by young adults. The Siemens Phonator demonstrated a wider suprathreshold operating range than did the Radioear B70A. (Author/CL)

76 FR 58768 - Ball Bearings and Parts Thereof From France, Germany, and Italy; Amended Final Results of...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-22

... determined for this company continues to be 5.47 percent. Germany: ``BSH Bosch and Siemens Hausgerate GmbH'' has been changed to ``BSH Bosch und Siemens Hausgerate GmbH;'' ``Volkswagon AG'' has been changed to...

Technical Note: Characterization of custom 3D printed multimodality imaging phantoms

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bieniosek, Matthew F.; Lee, Brian J.; Levin, Craig S., E-mail: cslevin@stanford.edu

Purpose: Imaging phantoms are important tools for researchers and technicians, but they can be costly and difficult to customize. Three dimensional (3D) printing is a widely available rapid prototyping technique that enables the fabrication of objects with 3D computer generated geometries. It is ideal for quickly producing customized, low cost, multimodal, reusable imaging phantoms. This work validates the use of 3D printed phantoms by comparing CT and PET scans of a 3D printed phantom and a commercial “Micro Deluxe” phantom. This report also presents results from a customized 3D printed PET/MRI phantom, and a customized high resolution imaging phantom withmore » sub-mm features. Methods: CT and PET scans of a 3D printed phantom and a commercial Micro Deluxe (Data Spectrum Corporation, USA) phantom with 1.2, 1.6, 2.4, 3.2, 4.0, and 4.8 mm diameter hot rods were acquired. The measured PET and CT rod sizes, activities, and attenuation coefficients were compared. A PET/MRI scan of a custom 3D printed phantom with hot and cold rods was performed, with photon attenuation and normalization measurements performed with a separate 3D printed normalization phantom. X-ray transmission scans of a customized two level high resolution 3D printed phantom with sub-mm features were also performed. Results: Results show very good agreement between commercial and 3D printed micro deluxe phantoms with less than 3% difference in CT measured rod diameter, less than 5% difference in PET measured rod diameter, and a maximum of 6.2% difference in average rod activity from a 10 min, 333 kBq/ml (9 μCi/ml) Siemens Inveon (Siemens Healthcare, Germany) PET scan. In all cases, these differences were within the measurement uncertainties of our setups. PET/MRI scans successfully identified 3D printed hot and cold rods on PET and MRI modalities. X-ray projection images of a 3D printed high resolution phantom identified features as small as 350 μm wide. Conclusions: This work shows that 3D printed phantoms can be functionally equivalent to commercially available phantoms. They are a viable option for quickly distributing and fabricating low cost, customized phantoms.« less

Martensitic transformation and phase diagram in ternary Co-V-Ga Heusler alloys

NASA Astrophysics Data System (ADS)

Xu, Xiao; Nagashima, Akihide; Nagasako, Makoto; Omori, Toshihiro; Kanomata, Takeshi; Kainuma, Ryosuke

2017-03-01

We report the martensitic transformation behavior in Co-V-Ga Heusler alloys. Thermoanalysis and thermomagnetization measurements were conducted to observe the martensitic transformation. By using a transmission electron microscope and an in situ X-ray diffractometer, martensitic transformation was found to occur from the L21 Heusler parent phase to the D022 martensite phase. Phase diagrams were determined for two pseudo-binary sections where martensitic transformation was detected. Magnetic properties, including the Curie temperatures and spontaneous magnetization of the parent phase, were also investigated. The magnetic properties showing behaviors different from those of NiMn-based alloys were found.

78 FR 25304 - Siemens Medical Solutions, USA, Inc., Oncology Care Systems (Radiation Oncology), Including On...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-04-30

..., USA, Inc., Oncology Care Systems (Radiation Oncology), Including On-Site Leased Workers From Source... Medical Solutions, USA, Inc., Oncology Care Systems (Radiation Oncology), including on- site leased... of February 2013, Siemens Medical Solutions, USA, Inc., Oncology Care Systems (Radiation Oncology...

UNCF, Thurgood Marshall Collaboration Encourages Teaching Careers in Math, Science

ERIC Educational Resources Information Center

Black Issues in Higher Education, 2005

2005-01-01

The Thurgood Marshall Scholarship Fund, the United Negro College Fund, and the Siemens Foundation have collaborated to establish the Siemens Teacher Scholarships, aimed at encouraging minority students to pursue teaching careers in math and science. This brief article discusses the details of the new program.

Siemens Foundation and the STEM Challenge

ERIC Educational Resources Information Center

Harper-Taylor, Jeniffer

2010-01-01

For more than 12 years, the Siemens Foundation has found unique ways to partner with organizations to support educational initiatives in science, technology, engineering and mathematics (STEM) in the United States. Its focus is clear--to educate the next generation of innovators by supporting math and science education from grade school to grad…

Synthesis, Characterization and Comparative Luminescence Studies of Rare-Earth-Doped Gd2O3 Nanoparticles

NASA Astrophysics Data System (ADS)

Pyngrope, D.; Singh, L. R.; Prasad, A. I.; Bora, A.

2018-04-01

A facile direct precipitation method was used for the synthesis of luminescence nanomaterial. Gd2O3 doped with rare earth element Eu3+ is synthesized by polyol route. The synthesized nanoparticles show their characteristic red emission. The nanoparticles are characterized by x-ray diffractometer (XRD), Fourier transform infrared spectroscopy (FTIR), transmission electron microscopy (TEM) and photoluminescence (PL) study. The synthesized nanoparticles are spherical particles with 30 nm size. The photoluminescence studies show the characteristic Eu3+ red emission. The PL study shows the intensity of the magnetic dipole transition ( 5 D0 \\to 7 F1 ) at 592 nm compared to that of the electronic dipole transition ( 5 D0 \\to 7 F2 ) at 615 nm. The nanomaterials can show significant application in various display devices and biomedical applications for tracking.

Echo-Planar Imaging Based J-Resolved Spectroscopic Imaging for Improved Metabolite Detection in Prostate Cancer

DTIC Science & Technology

2013-10-01

Scope: A major outcome is expected to be on improved detection ( specificity ) in differentiating malignant from benign prostate cancer using a novel...Digital Rectal Examination, prostate specific antigen , Four Dimensional (4D) Echo-Planar J-Resolved Spectroscopic Imaging (EP-JRESI); Citrate, Choline... prostate biopsy ranged from 3 to 8, while prostate - specific antigen varied from 2.8 to 20.6 ng/mL (mean of 6.84 ng/mL). A Siemens 3T MRI Scanner with

SU-C-9A-06: The Impact of CT Image Used for Attenuation Correction in 4D-PET

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cui, Y; Bowsher, J; Yan, S

2014-06-01

Purpose: To evaluate the appropriateness of using 3D non-gated CT image for attenuation correction (AC) in a 4D-PET (gated PET) imaging protocol used in radiotherapy treatment planning simulation. Methods: The 4D-PET imaging protocol in a Siemens PET/CT simulator (Biograph mCT, Siemens Medical Solutions, Hoffman Estates, IL) was evaluated. CIRS Dynamic Thorax Phantom (CIRS Inc., Norfolk, VA) with a moving glass sphere (8 mL) in the middle of its thorax portion was used in the experiments. The glass was filled with {sup 18}F-FDG and was in a longitudinal motion derived from a real patient breathing pattern. Varian RPM system (Varian Medicalmore » Systems, Palo Alto, CA) was used for respiratory gating. Both phase-gating and amplitude-gating methods were tested. The clinical imaging protocol was modified to use three different CT images for AC in 4D-PET reconstruction: first is to use a single-phase CT image to mimic actual clinical protocol (single-CT-PET); second is to use the average intensity projection CT (AveIP-CT) derived from 4D-CT scanning (AveIP-CT-PET); third is to use 4D-CT image to do the phase-matched AC (phase-matching- PET). Maximum SUV (SUVmax) and volume of the moving target (glass sphere) with threshold of 40% SUVmax were calculated for comparison between 4D-PET images derived with different AC methods. Results: The SUVmax varied 7.3%±6.9% over the breathing cycle in single-CT-PET, compared to 2.5%±2.8% in AveIP-CT-PET and 1.3%±1.2% in phasematching PET. The SUVmax in single-CT-PET differed by up to 15% from those in phase-matching-PET. The target volumes measured from single- CT-PET images also presented variations up to 10% among different phases of 4D PET in both phase-gating and amplitude-gating experiments. Conclusion: Attenuation correction using non-gated CT in 4D-PET imaging is not optimal process for quantitative analysis. Clinical 4D-PET imaging protocols should consider phase-matched 4D-CT image if available to achieve better accuracy.« less

A 16-ch module for thermal neutron detection using ZnS:6LiF scintillator with embedded WLS fibers coupled to SiPMs and its dedicated readout electronics

NASA Astrophysics Data System (ADS)

Mosset, J.-B.; Stoykov, A.; Greuter, U.; Gromov, A.; Hildebrandt, M.; Panzner, T.; Schlumpf, N.

2017-02-01

A scalable 16-ch thermal neutron detection system has been developed in the framework of the upgrade of a neutron diffractometer. The detector is based on a ZnS:6LiF scintillator with embedded WLS fibers which are read out with SiPMs. In this paper, we present the 16-ch module, the dedicated readout electronics, a direct comparison between the performance of the diffractometer obtained with the current 3He detector and with the 16-ch detection module, and the channel-to-channel uniformity.

The new materials science diffractometer STRESS-SPEC at FRM-II

NASA Astrophysics Data System (ADS)

Hofmann, M.; Schneider, R.; Seidl, G. A.; Rebelo-Kornmeier, J.; Wimpory, R. C.; Garbe, U.; Brokmeier, H.-G.

2006-11-01

In response to the development of new materials and the application of materials and components in new technologies the direct measurement, calculation and evaluation of textures and residual stresses has gained worldwide significance in recent years. In order to cater for the development of these analytical techniques the Materials Science Diffractometer STRESS-SPEC at FRM-II is designed to be equally applied to texture or residual stress analysis by virtue of its flexible configuration and the high neutron flux at the sample position. The instrument is now available for routine operation and here we present details of first experiments and instrument performance.

90-kilobar diamond-anvil high-pressure cell for use on an automatic diffractometer.

PubMed

Schiferl, D; Jamieson, J C; Lenko, J E

1978-03-01

A gasketed diamond-anvil high-pressure cell is described which can be used on a four-circle automatic diffractometer to collect x-ray intensity data from single-crystal samples subjected to truly hydrostatic pressures of over 90 kilobars. The force generating system exerts only forces normal to the diamond faces to obtain maximum reliability. A unique design allows exceptionally large open areas for maximum x-ray access and is particularly well suited for highly absorbing materials, as the x rays are not transmitted through the sample. Studies on ruby show that high-pressure crystal structure determinations may be done rapidly, reliably, and routinely with this system.

Portable X-ray diffractometer equipped with XRF for archaeometry

NASA Astrophysics Data System (ADS)

Uda, M.; Ishizaki, A.; Satoh, R.; Okada, K.; Nakajima, Y.; Yamashita, D.; Ohashi, K.; Sakuraba, Y.; Shimono, A.; Kojima, D.

2005-09-01

A portable X-ray diffractometer equipped with an X-ray fluorescence spectrometer was improved so as to get a diffraction pattern and a fluorescence spectrum simultaneously in air from one and the same small area on a specimen. Here, diffraction experiments were performed in two modes, i.e. an angle rotation mode and an energy dispersive mode. In the latter a diffraction pattern and a fluorescence spectrum were simultaneously recorded in a short time, 100 s or less, on one display. The diffractometer was tested in the field to confirm its performance. Targets chosen for this purpose were a bronze mirror from the Eastern Han Dynasty (25-220), and a stupa and its pedestal which are part of the painted statue of "Tamonten holding a stupa" from the Heian Period (794-1192), enshrined in the Engyouji temple founded in 996. The bronze mirror was identified as a product of the Han Dynasty from its chemical composition and the existence of the δ phase in the Cu-Sn alloy. The stupa and its pedestal were decorated with gold powder and gold leaf, respectively. From the XRF data of the pedestal, the underlying layer of gold leaf seems to have been painted with emerald green.

Neutron Time-of-Flight Diffractometer HIPPO at LANSCE

NASA Astrophysics Data System (ADS)

Vogel, Sven; Williams, Darrick; Zhao, Yusheng; Bennett, Kristin; von Dreele, Bob; Wenk, Hans-Rudolf

2004-03-01

The High-Pressure Preferred Orientation (HIPPO) neutron diffractometer is the first third-generation neutron time-of-flight powder diffractometer to be constructed in the United States. It produces extremely high intensity by virtue of a short (9 m) initial flight path on a high intensity water moderator and 1380 3He detector tubes covering 4.5 m2 of detector area from 10' to 150' in scattering angles. HIPPO was designed and manufactured as a joint effort between LANSCE and University of California with the goals of attaining world-class science and making neutron powder diffractometry an accessible and available tool to the national user community. Over two decades of momentum transfer are available (0.1-30 A-1) to support studies of amorphous solids; magnetic diffraction; small crystalline samples; and samples subjected to extreme environments such as temperature, pressure, or magnetic fields. The exceptionally high data rates of HIPPO also make it useful for time-resolved studies. In addition to the standard ancillary equipment (100-position sample/texture changer, closed-cycle He refrigerator, furnace), HIPPO has unique high-pressure cells capable of achieving pressures of 30 GPA at ambient and high (2000 K) temperature with samples up to 100 mm3 in volume.

Texture analysis at neutron diffractometer STRESS-SPEC

NASA Astrophysics Data System (ADS)

Brokmeier, H.-G.; Gan, W. M.; Randau, C.; Völler, M.; Rebelo-Kornmeier, J.; Hofmann, M.

2011-06-01

In response to the development of new materials and the application of materials and components in advanced technologies, non-destructive measurement methods of textures and residual stresses have gained worldwide significance in recent years. The materials science neutron diffractometer STRESS-SPEC at FRM II (Garching, Germany) is designed to be applied equally to texture and residual stress analyses by virtue of its very flexible configuration. Due to the high penetration capabilities of neutrons and the high neutron flux of STRESS-SPEC it allows a combined analysis of global texture, local texture, strain pole figure and FWHM pole figure in a wide variety of materials including metals, alloys, composites, ceramics and geological materials. Especially, the analysis of texture gradients in bulk materials using neutron diffraction has advantages over laboratory X-rays and EBSD for many scientific cases. Moreover, neutron diffraction is favourable for coarse-grained materials, where bulk information averaged over texture inhomogeneities is needed, and also stands out due to easy sample preparation. In future, the newly developed robot system for STRESS-SPEC will allow much more flexibility than an Eulerian cradle as on standard instruments. Five recent measurements are shown to demonstrate the wide range of possible texture applications at STRESS-SPEC diffractometer.

ETV Report:Siemens Model H-4XE-HO Open Channel UV System

EPA Science Inventory

Verification testing of the Siemens Barrier Sunligt H-4XE-HO UV System was completed at the UV Validation and Research Center of New York (UV Center), located in Johnstown, NY. The H-4XE System utilizes 16 high-output, low-pressure lamps oriented horizontally and parallel to the...

Development of a measurement and control system for a 10 kW@20 K refrigerator based on Siemens PLC S7-300

NASA Astrophysics Data System (ADS)

Li, J.; Liu, L. Q.; Liu, T.; Xu, X. D.; Dong, B.; Lu, W. H.; Pan, W.; Wu, J. H.; Xiong, L. Y.

2017-02-01

A 10 kW@20 K refrigerator has been established by the Technical Institute of Physics and Chemistry, Chinese Academy of Sciences. A measurement and control system based on Siemens PLC S7-300 for this 10 kW@20 K refrigerator is developed. According to the detailed measurement requirements, proper sensors and transmitters are adopted. Siemens S7-300 PLC CPU315-2 PN/DP operates as a master station. Two sets of ET200M DP remote expand I/O, one power meter, two compressors and one vacuum gauge operate as slave stations. Profibus-DP field communication and Modbus communication are used between the master station and the slave stations in this control system. The upper computer HMI (Human Machine Interface) is compiled using Siemens configuration software WinCC V7.0. The upper computer communicates with PLC by means of industrial Ethernet. After commissioning, this refrigerator has been operating with a 10 kW of cooling power at 20 K for more than 72 hours.

Comparison of estimates of left ventricular ejection fraction obtained from gated blood pool imaging, different software packages and cameras.

PubMed

Steyn, Rachelle; Boniaszczuk, John; Geldenhuys, Theodore

2014-01-01

To determine how two software packages, supplied by Siemens and Hermes, for processing gated blood pool (GBP) studies should be used in our department and whether the use of different cameras for the acquisition of raw data influences the results. The study had two components. For the first component, 200 studies were acquired on a General Electric (GE) camera and processed three times by three operators using the Siemens and Hermes software packages. For the second part, 200 studies were acquired on two different cameras (GE and Siemens). The matched pairs of raw data were processed by one operator using the Siemens and Hermes software packages. The Siemens method consistently gave estimates that were 4.3% higher than the Hermes method (p < 0.001). The differences were not associated with any particular level of left ventricular ejection fraction (LVEF). There was no difference in the estimates of LVEF obtained by the three operators (p = 0.1794). The reproducibility of estimates was good. In 95% of patients, using the Siemens method, the SD of the three estimates of LVEF by operator 1 was ≤ 1.7, operator 2 was ≤ 2.1 and operator 3 was ≤ 1.3. The corresponding values for the Hermes method were ≤ 2.5, ≤ 2.0 and ≤ 2.1. There was no difference in the results of matched pairs of data acquired on different cameras (p = 0.4933) CONCLUSION: Software packages for processing GBP studies are not interchangeable. The report should include the name and version of the software package used. Wherever possible, the same package should be used for serial studies. If this is not possible, the report should include the limits of agreement of the different packages. Data acquisition on different cameras did not influence the results.

Image-Based 2D Re-Projection for Attenuation Substitution in PET Neuroimaging.

PubMed

Laymon, Charles M; Minhas, Davneet S; Becker, Carl R; Matan, Cristy; Oborski, Matthew J; Price, Julie C; Mountz, James M

2018-02-27

In dual modality positron emission tomography (PET)/magnetic resonance imaging (MRI), attenuation correction (AC) methods are continually improving. Although a new AC can sometimes be generated from existing MR data, its application requires a new reconstruction. We evaluate an approximate 2D projection method that allows offline image-based reprocessing. 2-Deoxy-2-[ 18 F]fluoro-D-glucose ([ 18 F]FDG) brain scans were acquired (Siemens HR+) for six subjects. Attenuation data were obtained using the scanner's transmission source (SAC). Additional scanning was performed on a Siemens mMR including production of a Dixon-based MR AC (MRAC). The MRAC was imported to the HR+ and the PET data were reconstructed twice: once using native SAC (ground truth); once using the imported MRAC (imperfect AC). The re-projection method was implemented as follows. The MRAC PET was forward projected to approximately reproduce attenuation-corrected sinograms. The SAC and MRAC images were forward projected and converted to attenuation-correction factors (ACFs). The MRAC ACFs were removed from the MRAC PET sinograms by division; the SAC ACFs were applied by multiplication. The regenerated sinograms were reconstructed by filtered back projection to produce images (SUBAC PET) in which SAC has been substituted for MRAC. Ideally SUBAC PET should match SAC PET. Via coregistered T1 images, FreeSurfer (FS; MGH, Boston) was used to define a set of cortical gray matter regions of interest. Regional activity concentrations were extracted for SAC PET, MRAC PET, and SUBAC PET. SUBAC PET showed substantially smaller root mean square error than MRAC PET with averaged values of 1.5 % versus 8.1 %. Re-projection is a viable image-based method for the application of an alternate attenuation correction in neuroimaging.

Influence of eddy current, Maxwell and gradient field corrections on 3D flow visualization of 3D CINE PC-MRI data.

PubMed

Lorenz, Ramona; Bock, Jelena; Snyder, Jeff; Korvink, Jan G; Jung, Bernd A; Markl, Michael

2014-07-01

The measurement of velocities based on phase contrast MRI can be subject to different phase offset errors which can affect the accuracy of velocity data. The purpose of this study was to determine the impact of these inaccuracies and to evaluate different correction strategies on three-dimensional visualization. Phase contrast MRI was performed on a 3 T system (Siemens Trio) for in vitro (curved/straight tube models; venc: 0.3 m/s) and in vivo (aorta/intracranial vasculature; venc: 1.5/0.4 m/s) data. For comparison of the impact of different magnetic field gradient designs, in vitro data was additionally acquired on a wide bore 1.5 T system (Siemens Espree). Different correction methods were applied to correct for eddy currents, Maxwell terms, and gradient field inhomogeneities. The application of phase offset correction methods lead to an improvement of three-dimensional particle trace visualization and count. The most pronounced differences were found for in vivo/in vitro data (68%/82% more particle traces) acquired with a low venc (0.3 m/s/0.4 m/s, respectively). In vivo data acquired with high venc (1.5 m/s) showed noticeable but only minor improvement. This study suggests that the correction of phase offset errors can be important for a more reliable visualization of particle traces but is strongly dependent on the velocity sensitivity, object geometry, and gradient coil design. Copyright © 2013 Wiley Periodicals, Inc.

Assessment of SFR Wire Wrap Simulation Uncertainties

DOE Office of Scientific and Technical Information (OSTI.GOV)

Delchini, Marc-Olivier G.; Popov, Emilian L.; Pointer, William David

Predictive modeling and simulation of nuclear reactor performance and fuel are challenging due to the large number of coupled physical phenomena that must be addressed. Models that will be used for design or operational decisions must be analyzed for uncertainty to ascertain impacts to safety or performance. Rigorous, structured uncertainty analyses are performed by characterizing the model’s input uncertainties and then propagating the uncertainties through the model to estimate output uncertainty. This project is part of the ongoing effort to assess modeling uncertainty in Nek5000 simulations of flow configurations relevant to the advanced reactor applications of the Nuclear Energy Advancedmore » Modeling and Simulation (NEAMS) program. Three geometries are under investigation in these preliminary assessments: a 3-D pipe, a 3-D 7-pin bundle, and a single pin from the Thermal-Hydraulic Out-of-Reactor Safety (THORS) facility. Initial efforts have focused on gaining an understanding of Nek5000 modeling options and integrating Nek5000 with Dakota. These tasks are being accomplished by demonstrating the use of Dakota to assess parametric uncertainties in a simple pipe flow problem. This problem is used to optimize performance of the uncertainty quantification strategy and to estimate computational requirements for assessments of complex geometries. A sensitivity analysis to three turbulent models was conducted for a turbulent flow in a single wire wrapped pin (THOR) geometry. Section 2 briefly describes the software tools used in this study and provides appropriate references. Section 3 presents the coupling interface between Dakota and a computational fluid dynamic (CFD) code (Nek5000 or STARCCM+), with details on the workflow, the scripts used for setting up the run, and the scripts used for post-processing the output files. In Section 4, the meshing methods used to generate the THORS and 7-pin bundle meshes are explained. Sections 5, 6 and 7 present numerical results for the 3-D pipe, the single pin THORS mesh, and the 7-pin bundle mesh, respectively.« less

78 FR 69273 - Defense Federal Acquisition Regulation Supplement: Safeguarding Unclassified Controlled Technical...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-11-18

... list is added specifying the 13 pieces of information required for reporting. The time period a..., DoD 5000 series, DoD 8570.01-M, Directives (DoDD), National Industrial Security Operating Manual... on the scope of the proposed DFARS section 204.7400 including: university fundamental research should...

Building a Better Grid, in Partnership with the OMNETRIC Group and Siemens

DOE Office of Scientific and Technical Information (OSTI.GOV)

Waight, Jim; Grover, Shailendra; Wiedetz, Clark

In collaboration with Siemens and the National Renewable Energy Laboratory (NREL), OMNETRIC Group developed a distributed control hierarchy—based on an open field message bus (OpenFMB) framework—that allows control decisions to be made at the edge of the grid. The technology was validated and demonstrated at NREL’s Energy Systems Integration Facility.

Project GOLD: Growth Opportunities through Learning & Doing, Performance Reporting Period, November 1, 1996-February 28, 1998. National Workplace Literacy Program.

ERIC Educational Resources Information Center

Seminole Community Coll., Sanford, FL.

Project "Growth Opportunities through Learning and Doing" (GOLD), Seminole Community College's basic skills update program, enrolled 107 students at 2 manufacturing facilities from April 1995-February 1998. Employees from Siemens Telecom Network (formerly known as Siemens Stromberg-Carlson) studied offsite in a classroom equipped with 10 computers…

JPRS Report, Science & Technology, Europe & Latin America, Argentina: Specifications of ARGOS 380 MW Reactor.

DTIC Science & Technology

1988-02-18

programme. It has a licensing agreement with Siemens AG’s Kraftwerk Union AG, which is its minor shareholder. Under this agreement, ENACE has the...Argentine nuclear programme. It has a licensing agreement with Siemens AG’s Kraftwerk Union AG, which is its minor shareholder. Under this agreement, ENACE

CFD Investigation of Effect of Depth to Diameter Ratio on Dimple Flow Dynamics

DTIC Science & Technology

2007-06-01

contained dynamic vortical flow structures with behavior varying between each dimple studied. This dynamic vortex activity was observed to be linked... 1 1.1 Research Goals . . . . . . . . . . . . . . . . . . . . . . . 1 1.2 Motivation for Research . . . . . . . . . . . . . . . . . . 1 1.3...59 F. 1 . Pressure tap for ReD 20500 Rex 5000 0.05 h/D dimple . . . . . 66 F.2. Pressure tap for ReD 20500 Rex 77000 0.05 h/D dimple

Laas Geel (somaliland): 5000 Year-Old Paintings Captured in 3D

NASA Astrophysics Data System (ADS)

Grenier, L.; Antoniotti, P.; Hamon, G.; Happe, D.

2013-07-01

Discovered in 2002 by a French archaeology team conducted by Prof. X. Gutherz, Laas Geel (Somaliland), is probably one of the most remarkable archaeological site in the horn of Africa. Located in an isolated arid region, it is made of natural rocky shelters on which hundreds of colored paintings still remain in a particularly good state of conservation. The first studies achieved in the last decade let suppose that they are 5000 years old. After several studying and exploring expeditions, a 3Ddigitizing campaign has been carried out by Art Graphique et Patrimoine, under the direction of X. Gutherz, with the support of the cultural service of the French Embassy in Djibouti. The project was focused on three main goals: production of a high accuracy 3D-documentation for scientific needs, archiving the 3D digital print recorded on site for the conservation and the saving of this heritage, and finally diffusing the results throughout various kinds of media to reveal the site to the public, insisting on its vulnerability.

Redetermination of Na(3)TaF(8).

PubMed

Langer, Vratislav; Smrcok, Lubomír; Boca, Miroslav

2010-09-01

The crystal structure of trisodium octafluoridotantalate, Na(3)TaF(8), has been redetermined using diffractometer data collected at 153 K, resulting in more accurate bond distances and angles than obtained from a previous structure determination based on film data. The structure is built from layers running along [101], which are formed by distorted [TaF(8)] antiprisms and [NaF(6)] rectangular bipyramids sharing edges and corners. The individual layers are separated by eight-coordinated Na ions. Two atoms in the asymmetric unit are in special positions: the Ta atom is on a twofold axis in Wyckoff position 4e and one of the Na ions lies on an inversion centre in Wyckoff site 4d.

Transition to Turbulence in curved pipe

NASA Astrophysics Data System (ADS)

Hashemi, Amirreza; Loth, Francis

2014-11-01

Studies have shown that transitional turbulence in a curved pipe is delayed significantly compared with straight pipes. These analytical, numerical and experimental studies employed a helical geometry that is infinitely long such that the effect of the inlet and outlet can be neglected. The present study examined transition to turbulence in a finite curved pipe with a straight inlet/outlet and a 180 degrees curved pipe with a constant radius of curvature and diameter (D). We have employed the large scale direct numerical simulation (DNS) by using the spectral element method, nek5000, to simulate the flow field within curved pipe geometry with different curvature radii and Reynolds numbers to determine the point of the transition to turbulence. Long extensions for the inlet (5D) and outlet (20D) were used to diminish the effect of the boundary conditions. Our numerical results for radius of curvatures of 1.5D and 5D show transition turbulence is near Re = 3000. This is delayed compared with a straight pipe (Re = 2200) but still less that observed for helical geometries (Reynolds number less than 5000). Our research aims to describe the critical Reynolds number for transition to turbulence for a finite curved pipe at various curvature radii.

Dynamic Air Traffic Control Simulation of Profile Descent and High-Speed Approach Fuel Conservation Procedures.

DTIC Science & Technology

1980-05-01

FL240 and above 271 Aircraft Cruising FL230 and below 59 All Aircraft 330 D-7 Fuel (Average Pounds per Aircraft) Aircraft Cruising FL240 and above 3,467...15000 5440 5230 5020 4810 4640 4480 4320 4170 4030 3900 3770 -15 10000 5590 5420 5220 5000 4820 4660 4510 4360 4220 4090 3990 5000 5780 5600 5400...XAS 267 262 257 252 247 242 237 232 226 221 215 __ ,000 LBS/HR 22000 21200 20400 19600 18800 18000 17300 16600 15900 15200 145C0 IAS 264 260 255 250 245

Vacuum System Upgrade for Extended Q-Range Small-Angle Neutron Scattering Diffractometer (EQ-SANS) at SNS

DOE PAGES

Stone, Christopher M.; Williams, Derrick C.; Price, Jeremy P.

2016-09-23

The Extended Q-Range Small-Angle Neutron Scattering Diffractometer (EQ-SANS) instrument at the Spallation Neutron Source (SNS), Oak Ridge, Tennessee, incorporates a 69m3 detector vessel with a vacuum system which required an upgrade with respect to performance, ease of operation, and maintenance. The upgrade focused on improving pumping performance as well as optimizing system design to minimize opportunity for operational error. This upgrade provided the following practical contributions: Reduced time required to evacuate from atmospheric pressure to 2mTorr from 500-1,000 minutes to 60-70 minutes Provided turn-key automated control with a multi-faceted interlock for personnel and machine safety.

In-line metrology for roll-to-roll UV assisted nanoimprint lithography using diffractometry

NASA Astrophysics Data System (ADS)

Kreuzer, Martin; Whitworth, Guy L.; Francone, Achille; Gomis-Bresco, Jordi; Kehagias, Nikolaos; Sotomayor-Torres, Clivia M.

2018-05-01

We describe and discuss the optical design of a diffractometer to carry out in-line quality control during roll-to-roll nanoimprinting. The tool measures diffractograms in reflection geometry, through an aspheric lens to gain fast, non-invasive information of any changes to the critical dimensions of target grating structures. A stepwise tapered linear grating with constant period was fabricated in order to detect the variation in grating linewidth through diffractometry. The minimum feature change detected was ˜40 nm to a precision of 10 nm. The diffractometer was then integrated with a roll-to-roll UV assisted nanoimprint lithography machine to gain dynamic measurements in situ.

Vacuum System Upgrade for Extended Q-Range Small-Angle Neutron Scattering Diffractometer (EQ-SANS) at SNS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stone, Christopher M.; Williams, Derrick C.; Price, Jeremy P.

The Extended Q-Range Small-Angle Neutron Scattering Diffractometer (EQ-SANS) instrument at the Spallation Neutron Source (SNS), Oak Ridge, Tennessee, incorporates a 69m3 detector vessel with a vacuum system which required an upgrade with respect to performance, ease of operation, and maintenance. The upgrade focused on improving pumping performance as well as optimizing system design to minimize opportunity for operational error. This upgrade provided the following practical contributions: Reduced time required to evacuate from atmospheric pressure to 2mTorr from 500-1,000 minutes to 60-70 minutes Provided turn-key automated control with a multi-faceted interlock for personnel and machine safety.

AND/R: Advanced neutron diffractometer/reflectometer for investigation of thin films and multilayers for the life sciences

PubMed Central

Dura, Joseph A.; Pierce, Donald J.; Majkrzak, Charles F.; Maliszewskyj, Nicholas C.; McGillivray, Duncan J.; Lösche, Mathias; O'Donovan, Kevin V.; Mihailescu, Mihaela; Perez-Salas, Ursula; Worcester, David L.; White, Stephen H.

2011-01-01

An elastic neutron scattering instrument, the advanced neutron diffractometer/reflectometer (AND/R), has recently been commissioned at the National Institute of Standards and Technology Center for Neutron Research. The AND/R is the centerpiece of the Cold Neutrons for Biology and Technology partnership, which is dedicated to the structural characterization of thin films and multilayers of biological interest. The instrument is capable of measuring both specular and nonspecular reflectivity, as well as crystalline or semicrystalline diffraction at wave-vector transfers up to approximately 2.20 Å−1. A detailed description of this flexible instrument and its performance characteristics in various operating modes are given. PMID:21892232

MO-DE-202-00: Image-Guided Interventions: Advances in Intraoperative Imaging, Guidance, and An Emerging Role for Medical Physics in Surgery

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

At least three major trends in surgical intervention have emerged over the last decade: a move toward more minimally invasive (or non-invasive) approach to the surgical target; the development of high-precision treatment delivery techniques; and the increasing role of multi-modality intraoperative imaging in support of such procedures. This symposium includes invited presentations on recent advances in each of these areas and the emerging role for medical physics research in the development and translation of high-precision interventional techniques. The four speakers are: Keyvan Farahani, “Image-guided focused ultrasound surgery and therapy” Jeffrey H. Siewerdsen, “Advances in image registration and reconstruction for image-guidedmore » neurosurgery” Tina Kapur, “Image-guided surgery and interventions in the advanced multimodality image-guided operating (AMIGO) suite” Raj Shekhar, “Multimodality image-guided interventions: Multimodality for the rest of us” Learning Objectives: Understand the principles and applications of HIFU in surgical ablation. Learn about recent advances in 3D–2D and 3D deformable image registration in support of surgical safety and precision. Learn about recent advances in model-based 3D image reconstruction in application to intraoperative 3D imaging. Understand the multi-modality imaging technologies and clinical applications investigated in the AMIGO suite. Understand the emerging need and techniques to implement multi-modality image guidance in surgical applications such as neurosurgery, orthopaedic surgery, vascular surgery, and interventional radiology. Research supported by the NIH and Siemens Healthcare.; J. Siewerdsen; Grant Support - National Institutes of Health; Grant Support - Siemens Healthcare; Grant Support - Carestream Health; Advisory Board - Carestream Health; Licensing Agreement - Carestream Health; Licensing Agreement - Elekta Oncology.; T. Kapur, P41EB015898; R. Shekhar, Funding: R42CA137886 and R41CA192504 Disclosure and CoI: IGI Technologies, small-business partner on the grants.« less

MO-DE-202-03: Image-Guided Surgery and Interventions in the Advanced Multimodality Image-Guided Operating (AMIGO) Suite

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kapur, T.

At least three major trends in surgical intervention have emerged over the last decade: a move toward more minimally invasive (or non-invasive) approach to the surgical target; the development of high-precision treatment delivery techniques; and the increasing role of multi-modality intraoperative imaging in support of such procedures. This symposium includes invited presentations on recent advances in each of these areas and the emerging role for medical physics research in the development and translation of high-precision interventional techniques. The four speakers are: Keyvan Farahani, “Image-guided focused ultrasound surgery and therapy” Jeffrey H. Siewerdsen, “Advances in image registration and reconstruction for image-guidedmore » neurosurgery” Tina Kapur, “Image-guided surgery and interventions in the advanced multimodality image-guided operating (AMIGO) suite” Raj Shekhar, “Multimodality image-guided interventions: Multimodality for the rest of us” Learning Objectives: Understand the principles and applications of HIFU in surgical ablation. Learn about recent advances in 3D–2D and 3D deformable image registration in support of surgical safety and precision. Learn about recent advances in model-based 3D image reconstruction in application to intraoperative 3D imaging. Understand the multi-modality imaging technologies and clinical applications investigated in the AMIGO suite. Understand the emerging need and techniques to implement multi-modality image guidance in surgical applications such as neurosurgery, orthopaedic surgery, vascular surgery, and interventional radiology. Research supported by the NIH and Siemens Healthcare.; J. Siewerdsen; Grant Support - National Institutes of Health; Grant Support - Siemens Healthcare; Grant Support - Carestream Health; Advisory Board - Carestream Health; Licensing Agreement - Carestream Health; Licensing Agreement - Elekta Oncology.; T. Kapur, P41EB015898; R. Shekhar, Funding: R42CA137886 and R41CA192504 Disclosure and CoI: IGI Technologies, small-business partner on the grants.« less

MO-DE-202-01: Image-Guided Focused Ultrasound Surgery and Therapy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Farahani, K.

At least three major trends in surgical intervention have emerged over the last decade: a move toward more minimally invasive (or non-invasive) approach to the surgical target; the development of high-precision treatment delivery techniques; and the increasing role of multi-modality intraoperative imaging in support of such procedures. This symposium includes invited presentations on recent advances in each of these areas and the emerging role for medical physics research in the development and translation of high-precision interventional techniques. The four speakers are: Keyvan Farahani, “Image-guided focused ultrasound surgery and therapy” Jeffrey H. Siewerdsen, “Advances in image registration and reconstruction for image-guidedmore » neurosurgery” Tina Kapur, “Image-guided surgery and interventions in the advanced multimodality image-guided operating (AMIGO) suite” Raj Shekhar, “Multimodality image-guided interventions: Multimodality for the rest of us” Learning Objectives: Understand the principles and applications of HIFU in surgical ablation. Learn about recent advances in 3D–2D and 3D deformable image registration in support of surgical safety and precision. Learn about recent advances in model-based 3D image reconstruction in application to intraoperative 3D imaging. Understand the multi-modality imaging technologies and clinical applications investigated in the AMIGO suite. Understand the emerging need and techniques to implement multi-modality image guidance in surgical applications such as neurosurgery, orthopaedic surgery, vascular surgery, and interventional radiology. Research supported by the NIH and Siemens Healthcare.; J. Siewerdsen; Grant Support - National Institutes of Health; Grant Support - Siemens Healthcare; Grant Support - Carestream Health; Advisory Board - Carestream Health; Licensing Agreement - Carestream Health; Licensing Agreement - Elekta Oncology.; T. Kapur, P41EB015898; R. Shekhar, Funding: R42CA137886 and R41CA192504 Disclosure and CoI: IGI Technologies, small-business partner on the grants.« less

MO-DE-202-04: Multimodality Image-Guided Surgery and Intervention: For the Rest of Us

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shekhar, R.

At least three major trends in surgical intervention have emerged over the last decade: a move toward more minimally invasive (or non-invasive) approach to the surgical target; the development of high-precision treatment delivery techniques; and the increasing role of multi-modality intraoperative imaging in support of such procedures. This symposium includes invited presentations on recent advances in each of these areas and the emerging role for medical physics research in the development and translation of high-precision interventional techniques. The four speakers are: Keyvan Farahani, “Image-guided focused ultrasound surgery and therapy” Jeffrey H. Siewerdsen, “Advances in image registration and reconstruction for image-guidedmore » neurosurgery” Tina Kapur, “Image-guided surgery and interventions in the advanced multimodality image-guided operating (AMIGO) suite” Raj Shekhar, “Multimodality image-guided interventions: Multimodality for the rest of us” Learning Objectives: Understand the principles and applications of HIFU in surgical ablation. Learn about recent advances in 3D–2D and 3D deformable image registration in support of surgical safety and precision. Learn about recent advances in model-based 3D image reconstruction in application to intraoperative 3D imaging. Understand the multi-modality imaging technologies and clinical applications investigated in the AMIGO suite. Understand the emerging need and techniques to implement multi-modality image guidance in surgical applications such as neurosurgery, orthopaedic surgery, vascular surgery, and interventional radiology. Research supported by the NIH and Siemens Healthcare.; J. Siewerdsen; Grant Support - National Institutes of Health; Grant Support - Siemens Healthcare; Grant Support - Carestream Health; Advisory Board - Carestream Health; Licensing Agreement - Carestream Health; Licensing Agreement - Elekta Oncology.; T. Kapur, P41EB015898; R. Shekhar, Funding: R42CA137886 and R41CA192504 Disclosure and CoI: IGI Technologies, small-business partner on the grants.« less

MO-DE-202-02: Advances in Image Registration and Reconstruction for Image-Guided Neurosurgery

DOE Office of Scientific and Technical Information (OSTI.GOV)

Siewerdsen, J.

At least three major trends in surgical intervention have emerged over the last decade: a move toward more minimally invasive (or non-invasive) approach to the surgical target; the development of high-precision treatment delivery techniques; and the increasing role of multi-modality intraoperative imaging in support of such procedures. This symposium includes invited presentations on recent advances in each of these areas and the emerging role for medical physics research in the development and translation of high-precision interventional techniques. The four speakers are: Keyvan Farahani, “Image-guided focused ultrasound surgery and therapy” Jeffrey H. Siewerdsen, “Advances in image registration and reconstruction for image-guidedmore » neurosurgery” Tina Kapur, “Image-guided surgery and interventions in the advanced multimodality image-guided operating (AMIGO) suite” Raj Shekhar, “Multimodality image-guided interventions: Multimodality for the rest of us” Learning Objectives: Understand the principles and applications of HIFU in surgical ablation. Learn about recent advances in 3D–2D and 3D deformable image registration in support of surgical safety and precision. Learn about recent advances in model-based 3D image reconstruction in application to intraoperative 3D imaging. Understand the multi-modality imaging technologies and clinical applications investigated in the AMIGO suite. Understand the emerging need and techniques to implement multi-modality image guidance in surgical applications such as neurosurgery, orthopaedic surgery, vascular surgery, and interventional radiology. Research supported by the NIH and Siemens Healthcare.; J. Siewerdsen; Grant Support - National Institutes of Health; Grant Support - Siemens Healthcare; Grant Support - Carestream Health; Advisory Board - Carestream Health; Licensing Agreement - Carestream Health; Licensing Agreement - Elekta Oncology.; T. Kapur, P41EB015898; R. Shekhar, Funding: R42CA137886 and R41CA192504 Disclosure and CoI: IGI Technologies, small-business partner on the grants.« less

77 FR 34935 - Foreign-Trade Zone 161; Temporary/Interim Manufacturing Authority; Siemens Energy, Inc., (Wind...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-12

... DEPARTMENT OF COMMERCE Foreign-Trade Zones Board [Docket T-4-2012] Foreign-Trade Zone 161; Temporary/Interim Manufacturing Authority; Siemens Energy, Inc., (Wind Turbine Nacelles and Hubs); Notice of Approval On April 2, 2012, the Executive Secretary of the Foreign-Trade Zones (FTZ) Board filed an application submitted by the Board of County...

DoD Consumer Affairs Program

DTIC Science & Technology

1982-08-12

Suggestion boxes. 11 Customer "Want" slips. (c) Communications to Consumers on Issues and Decisions. Consumers are informed of issues and pending final...of Federal Consumer Programs," September 26, 1979 (c) DoD Directive 5000. 19, "Policies for the Management and Control of Intotmation Requirements...b) to update responsibilities and guidelines for the DoD Consumer Affairs Program. B. APPLICABILITY This Directive applies to the Office of the

The Optics and Alignment of the Divergent Beam Laboratory X-ray Powder Diffractometer and its Calibration Using NIST Standard Reference Materials.

PubMed

Cline, James P; Mendenhall, Marcus H; Black, David; Windover, Donald; Henins, Albert

2015-01-01

The laboratory X-ray powder diffractometer is one of the primary analytical tools in materials science. It is applicable to nearly any crystalline material, and with advanced data analysis methods, it can provide a wealth of information concerning sample character. Data from these machines, however, are beset by a complex aberration function that can be addressed through calibration with the use of NIST Standard Reference Materials (SRMs). Laboratory diffractometers can be set up in a range of optical geometries; considered herein are those of Bragg-Brentano divergent beam configuration using both incident and diffracted beam monochromators. We review the origin of the various aberrations affecting instruments of this geometry and the methods developed at NIST to align these machines in a first principles context. Data analysis methods are considered as being in two distinct categories: those that use empirical methods to parameterize the nature of the data for subsequent analysis, and those that use model functions to link the observation directly to a specific aspect of the experiment. We consider a multifaceted approach to instrument calibration using both the empirical and model based data analysis methods. The particular benefits of the fundamental parameters approach are reviewed.

Sinusoidal Siemens star spatial frequency response measurement errors due to misidentified target centers

DOE PAGES

Birch, Gabriel Carisle; Griffin, John Clark

2015-07-23

Numerous methods are available to measure the spatial frequency response (SFR) of an optical system. A recent change to the ISO 12233 photography resolution standard includes a sinusoidal Siemens star test target. We take the sinusoidal Siemens star proposed by the ISO 12233 standard, measure system SFR, and perform an analysis of errors induced by incorrectly identifying the center of a test target. We show a closed-form solution for the radial profile intensity measurement given an incorrectly determined center and describe how this error reduces the measured SFR of the system. As a result, using the closed-form solution, we proposemore » a two-step process by which test target centers are corrected and the measured SFR is restored to the nominal, correctly centered values.« less

A high performance neutron powder diffractometer at 3 MW Triga Mark-II research reactor in Bangladesh

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kamal, I., E-mail: imtiaz-kamal26@yahoo.com; Yunus, S. M., E-mail: yunussm11@yahoo.com; Datta, T. K., E-mail: tk-datta4@yahoo.com

2016-07-12

A high performance neutron diffractometer called Savar Neutron Diffractometer (SAND) was built and installed at radial beam port-2 of TRIGA Mark II research reactor at AERE, Savar, Dhaka, Bangladesh. Structural studies of materials are being done by this technique to characterize materials crystallograpohically and magnetically. The micro-structural information obtainable by neutron scattering method is very essential for determining its technological applications. This technique is unique for understanding the magnetic behavior in magnetic materials. Ceramic, steel, electronic and electric industries can be benefited from this facility for improving their products and fabrication process. This instrument consists of a Popovicimonochromator with amore » large linear position sensitive detector array. The monochromator consists of nine blades of perfect single crystal of silicon with 6 mm thickness each. The monochromator design was optimized to provide maximum flux on 3 mm diameter cylindrical sample with a relatively flat angular dependence of resolution. Five different wave lengths can be selected by orienting the crystal at various angles. A sapphire filter was used before the primary collimator to minimize the first neutron. The detector assembly is composed of 15 linear position sensitive proportional counters placed at either 1.1 m or 1.6 m from the sample position and enclosed in a air pad supported high density polythene shield. Position sensing is obtained by charge division using 1-wide NIM position encoding modules (PEM). The PEMs communicate with the host computer via USB. The detector when placed at 1.1 m, subtends 30° (2θ) at each step and covers 120° in 4 steps. When the detector is placed at 1.6 m it subtends 20° at each step and covers 120° in 6 steps. The instrument supports both low and high temperature sample environment. The instrument supports both low and high temperature sample environment. The diffractometer is a state-of-the art technology for diffraction study in our country.« less

A high performance neutron powder diffractometer at 3 MW Triga Mark-II research reactor in Bangladesh

NASA Astrophysics Data System (ADS)

Kamal, I.; Yunus, S. M.; Datta, T. K.; Zakaria, A. K. M.; Das, A. K.; Aktar, S.; Hossain, S.; Berliner, R.; Yelon, W. B.

2016-07-01

A high performance neutron diffractometer called Savar Neutron Diffractometer (SAND) was built and installed at radial beam port-2 of TRIGA Mark II research reactor at AERE, Savar, Dhaka, Bangladesh. Structural studies of materials are being done by this technique to characterize materials crystallograpohically and magnetically. The micro-structural information obtainable by neutron scattering method is very essential for determining its technological applications. This technique is unique for understanding the magnetic behavior in magnetic materials. Ceramic, steel, electronic and electric industries can be benefited from this facility for improving their products and fabrication process. This instrument consists of a Popovicimonochromator with a large linear position sensitive detector array. The monochromator consists of nine blades of perfect single crystal of silicon with 6mm thickness each. The monochromator design was optimized to provide maximum flux on 3mm diameter cylindrical sample with a relatively flat angular dependence of resolution. Five different wave lengths can be selected by orienting the crystal at various angles. A sapphire filter was used before the primary collimator to minimize the first neutron. The detector assembly is composed of 15 linear position sensitive proportional counters placed at either 1.1 m or 1.6 m from the sample position and enclosed in a air pad supported high density polythene shield. Position sensing is obtained by charge division using 1-wide NIM position encoding modules (PEM). The PEMs communicate with the host computer via USB. The detector when placed at 1.1 m, subtends 30˚ (2θ) at each step and covers 120˚ in 4 steps. When the detector is placed at 1.6 m it subtends 20˚ at each step and covers 120˚ in 6 steps. The instrument supports both low and high temperature sample environment. The instrument supports both low and high temperature sample environment. The diffractometer is a state-of-the art technology for diffraction study in our country.

46 CFR 76.33-5 - Zoning.

Code of Federal Regulations, 2011 CFR

2011-10-01

... having a combined volume not exceeding 5,000 cubic feet may be connected on the same zone. (d) Where a space is of such size that one accumulator is not sufficient, not more than two accumulators may be...

46 CFR 76.33-5 - Zoning.

Code of Federal Regulations, 2010 CFR

2010-10-01

... having a combined volume not exceeding 5,000 cubic feet may be connected on the same zone. (d) Where a space is of such size that one accumulator is not sufficient, not more than two accumulators may be...

Comparison of photorefractive keratectomy and laser in situ keratomileusis for myopia of -6 D or less using the Nidek EC-5000 laser.

PubMed

Fernández, A P; Jaramillo, J; Jaramillo, M

2000-01-01

We compared the efficacy, predictability, and safety of photorefractive keratectomy (PRK) and laser in situ keratomileusis (LASIK) for the surgical correction of low and moderate myopia. A retrospective study was performed to evaluate uncorrected and spectacle-corrected visual acuity, and manifest refraction 1 year after PRK or LASIK. All procedures were done using an automatic microkeratome (Chiron Ophthalmic) and the Nidek EC-5000 excimer laser. PRK was performed in 75 eyes of 45 patients and LASIK in 133 eyes of 77 patients. Mean age for PRK patients was 32.8 years (range, 18 to 52 yr) and LASIK patients was 29.6 years (range, 18 to 49 yr). Mean preoperative spherical equivalent refraction for PRK patients was -3.28 D (range, -1.00 to -6.00 D) and LASIK, -3.86 D (range, -1.00 to -6.00 D). One year after surgery, mean spherical equivalent refraction for Group 1 (baseline, -1.00 to -3.00 D) PRK eyes was -0.18 +/- 0.61 D (range, -1.50 to +0.75 D) and for LASIK eyes, -0.08 +/- 0.61 D (range, -1.50 to +1.62 D), with no statistically significant difference. For Group 2 eyes (baseline, -3.25 to -6.00 D), mean spherical equivalent refraction for PRK eyes was -0.44 +/- 0.87 D (range, -2.00 to +2.12 D) and for LASIK eyes, -0.09 +/- 0.83 D (range, -1.50 to +1.75 D), with no statistically significant difference. The antilogarithm of the mean UCVA (antilogUCVA) in Group 1 for PRK was 0.79 +/- 0.21 (20/25) and for LASIK was 0.87 +/- 0.19 (20/23), with no statistically significant difference. The antilogUCVA in Group 2 for PRK eyes was 0.70 +/- 0.24 (20/28) and for LASIK eyes was 0.83 +/- 0.18 (20/24), with a statistically significant difference (0.7 vs. 0.83, P < .005). The percentage of eyes with a postoperative UCVA >20/40 in Group 1 for PRK was 91.5% (38 eyes) and for LASIK was 95% (50 eyes) (no statistically significant difference), and in Group 2 for PRK eyes, it was 82% (27 eyes) and 97.5% (78 eyes) for LASIK (statistically significant difference, P < .05). PRK and LASIK with the Nidek EC-5000 excimer laser are effective and safe for correcting low to moderate myopia, but LASIK eyes showed better results for moderate myopia in terms of uncorrected visual acuity.

Evaluation of Instrumentation for Measuring Undissolved Water in Aviation Turbine Fuels per ASTM D3240

DTIC Science & Technology

2015-11-05

Undissolved Water in Aviation Turbine Fuels per ASTM D3240 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) Joel Schmitigal... water ) in Aviation Turbine Fuels per ASTM D3240 15. SUBJECT TERMS fuel, JP-8, aviation fuel, contamination, free water , undissolved water , Aqua-Glo 16...Michigan 48397-5000 Evaluation of Instrumentation for Measuring Undissolved Water in Aviation Turbine Fuels per ASTM D3240 Joel Schmitigal Force

Impact of light exposure on thyroid-stimulating hormone results using the Siemens Advia Centaur TSH-3Ultra assay.

PubMed

Armer, Jane; Giles, Diane; Lancaster, Ian; Brownbill, Kathryn

2017-09-01

Background Thyroid-stimulating hormone (TSH) is used as the first-line test of thyroid function. Siemens Healthcare Diagnostics recommend that Siemens Centaur reagents must be protected from light in the assay information and on reagent packaging. We have compared the effect of light exposure on results using Siemens TSH-3Ultra and follicle-stimulating hormone reagents. The thyroid-stimulating hormone reagent includes fluoroscein thiocyanate whereas the follicle-stimulating hormone reagent does not. Methods Three levels of quality controls were analysed using SiemensTSH-3Ultra and follicle-stimulating hormone reagent packs that had been kept protected from light or exposed to light at 6-h intervals for 48 h and then at 96 h. Results Thyroid-stimulating hormone results were significantly lower after exposure of TSH-3Ultra reagent packs to light. Results were >15% lower at all three levels of quality control following 18 h of light exposure and continued to decrease until 96 h. There was no significant difference in follicle-stimulating hormone results whether reagents had been exposed to or protected from light. Conclusions Thyroid-stimulating hormone results but not follicle-stimulating hormone results are lowered after exposure of reagent packs to light. Laboratories must ensure that TSH-3Ultra reagents are not exposed to light and analyse quality control samples on every reagent pack to check that there has not been light exposure prior to delivery. The labelling on TSH-3Ultra reagent packs should reflect the significant effect of light exposure compared with the follicle-stimulating hormone reagent. We propose that the effect of light exposure on binding of fluoroscein thiocyanate to the solid phase antibody causes the falsely low results.

Modeling and 3D Visualization for Evaluation of Anti-Terrorism/Force Protection Alternatives: Phase II Final Report

DTIC Science & Technology

2006-11-21

SCHOOL Monterey, California 93943-5000 COL David A. Smarsh, USAF Dr. Leonard A. Ferrari Acting President...1.3.6 Planet 9 Studios David Colleen, CEO Chris Greuel, 3D Model Engineer Dan Ancona, Documentation and Training Carlos Newcomb, 3D Imagery...informational forum of M&S professionals working in the service of naval installation security. David Colleen, CEO, Planet 9 Studios, gave a

Note: Detector collimators for the nanoscale ordered materials diffractometer instrument at the Spallation Neutron Source

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tamalonis, A.; Weber, J. K. R.; Neuefeind, J. C.

2015-09-01

Five neutron collimator designs were constructed and tested at the nanoscale ordered materials diffractometer (NOMAD) instrument. Collimators were made from High Density PolyEthylene (HDPE) or 5% borated HDPE. In all cases, collimators improved the signal to background ratio and reduced detection of secondary scattering. In the Q-range 10-20 (angstrom) -1, signal to background ratio improved by factors of approximately 1.6 and 2.0 for 50 and 100 mm deep collimators, respectively. In the Q-range 40-50 angstrom -1, the improvement factors were 1.8 and 2.7. Secondary scattering as measured at Q similar to 9.5 angstrom -1 was significantly decreased when the collimatorsmore » were installed.« less

Improved sample manipulation at the STRESS-SPEC neutron diffractometer using an industrial 6-axis robot for texture and strain analyses

NASA Astrophysics Data System (ADS)

Randau, C.; Brokmeier, H. G.; Gan, W. M.; Hofmann, M.; Voeller, M.; Tekouo, W.; Al-hamdany, N.; Seidl, G.; Schreyer, A.

2015-09-01

The materials science neutron diffractometer STRESS-SPEC located at FRM II is a dedicated instrument for strain and pole figure measurements. Both methods make complementary demands on sample handling. On one hand pole figure measurements need a high degree of freedom to orient small samples and on the other hand in strain investigations it is often necessary to handle large and heavy components. Therefore a robot based sample positioning system was developed, which has the capability to provide both possibilities. Based on this new robot system further developments like a full automated sample changer system for texture measurements were accomplished. Moreover this system opens the door for combined strain and texture analysis at STRESS-SPEC.

Note: Detector collimators for the nanoscale ordered materials diffractometer instrument at the Spallation Neutron Source

DOE PAGES

Tamalonis, A.; Weber, J. K. R.; Neuefeind, J. C.; ...

2015-09-09

We constructed and tested five neutron collimator designs using the nanoscale ordered materials diffractometer (NOMAD) instrument. Collimators were made from High Density PolyEthylene (HDPE) or 5% borated HDPE. In all cases, collimators improved the signal to background ratio and reduced detection of secondary scattering. Moreover, in the Q-range 10-20 Å -1, signal to background ratio improved by factors of approximately 1.6 and 2.0 for 50 and 100 mm deep collimators, respectively. In the Q-range 40-50 Å -1, the improvement factors were 1.8 and 2.7. Secondary scattering as measured at Q similar to 9.5 Å -1 was significantly decreased when themore » collimators were installed.« less

The effect of glazing and aging on the surface properties of CAD/CAM resin blocks

PubMed Central

Tuncer, Safa; Kara, Dilan; Demirci, Mustafa

2018-01-01

PURPOSE To investigate the effect of accelerated aging on surface properties of glazed CAD/CAM resin blocks using a 2D surface profilometer and a 3D non-contact optical profilometer. MATERIALS AND METHODS Three types of CAD/CAM resin restorative materials, LAVA Ultimate (3M ESPE, St Paul, MN, USA), VITA Enamic (Vita Zahnfabrik H. Rauter, Bad Säckingen, Germany), and Cerasmart (GC Corparation, Tokyo, Japan) were used for this study. CAD/CAM blocks were cut in 3-mm thickness slabs and divided into three groups; Group 1: control group (specimens polished with 600 grit SCI paper); Group 2: specimens sandblasted, silanized, and glazed with Optiglaze Color (GC); Group 3: glazed specimens subjected to 5000 thermocycles (n=15). The surface roughness (Ra and Rz) was evaluated using a profilometer and a 3D scanning instrument. Data were analyzed using two-way ANOVA and Tukey's post-hoc test (P<.05). RESULTS LAVA, VITA, and Cerasmart exhibited statistically similar Ra and Rz values for each group (P>.05). For VITA and Cerasmart, the specimens in Group 1 exhibited significantly higher Ra values than Group 2 (P<.05). Group 1 (0.502 Ra), Group 2 (0.384 Ra), and Group 3 (0.431 Ra) exhibited statistically similar Ra values for LAVA (P=.062). After 5000 thermocycles, surface roughness values did not change significantly for glazed LAVA, VITA, and Cerasmart (P>.05). CONCLUSION Glaze material Optiglaze Color makes CAD/CAM resin surfaces smooth and glazed CAD/CAM surfaces seem resistant to deterioration under 5000 thermocycles. PMID:29503714

The effect of glazing and aging on the surface properties of CAD/CAM resin blocks.

PubMed

Tekçe, Neslihan; Fidan, Sinan; Tuncer, Safa; Kara, Dilan; Demirci, Mustafa

2018-02-01

To investigate the effect of accelerated aging on surface properties of glazed CAD/CAM resin blocks using a 2D surface profilometer and a 3D non-contact optical profilometer. Three types of CAD/CAM resin restorative materials, LAVA Ultimate (3M ESPE, St Paul, MN, USA), VITA Enamic (Vita Zahnfabrik H. Rauter, Bad Säckingen, Germany), and Cerasmart (GC Corparation, Tokyo, Japan) were used for this study. CAD/CAM blocks were cut in 3-mm thickness slabs and divided into three groups; Group 1: control group (specimens polished with 600 grit SCI paper); Group 2: specimens sandblasted, silanized, and glazed with Optiglaze Color (GC); Group 3: glazed specimens subjected to 5000 thermocycles (n=15). The surface roughness (R a and R z ) was evaluated using a profilometer and a 3D scanning instrument. Data were analyzed using two-way ANOVA and Tukey's post-hoc test ( P <.05). LAVA, VITA, and Cerasmart exhibited statistically similar R a and R z values for each group ( P >.05). For VITA and Cerasmart, the specimens in Group 1 exhibited significantly higher R a values than Group 2 ( P <.05). Group 1 (0.502 R a ), Group 2 (0.384 R a ), and Group 3 (0.431 R a ) exhibited statistically similar R a values for LAVA ( P =.062). After 5000 thermocycles, surface roughness values did not change significantly for glazed LAVA, VITA, and Cerasmart ( P >.05). Glaze material Optiglaze Color makes CAD/CAM resin surfaces smooth and glazed CAD/CAM surfaces seem resistant to deterioration under 5000 thermocycles.

Tracing the 5000-year recorded history of inorganic thin films from ˜3000 BC to the early 1900s AD

NASA Astrophysics Data System (ADS)

Greene, J. E.

2014-12-01

Gold is very likely the first metal discovered by man, more than 11 000 years ago. However, unlike copper (˜9000 BC), bronze (˜3500 BC), and wrought iron (˜2500-3000 BC), gold is too soft for fabrication of tools and weapons. Instead, it was used for decoration, religious artifacts, and commerce. The earliest documented inorganic thin films were gold layers, some less than 3000 Å thick, produced chemi-mechanically by Egyptians approximately 5000 years ago. Examples, gilded on statues and artifacts (requiring interfacial adhesion layers), were found in early stone pyramids dating to ˜2650 BC in Saqqara, Egypt. Spectacular samples of embossed Au sheets date to at least 2600 BC. The Moche Indians of northern Peru developed electroless gold plating (an auto-catalytic reaction) in ˜100 BC and applied it to intricate Cu masks. The earliest published electroplating experiments were ˜1800 AD, immediately following the invention of the dc electrochemical battery by Volta. Chemical vapor deposition (CVD) of metal films was reported in 1649, atmospheric arc deposition of oxides (Priestley) in the mid-1760s, and atmospheric plasmas (Siemens) in 1857. Sols were produced in the mid-1850s (Faraday) and sol-gel films synthesized in 1885. Vapor phase film growth including sputter deposition (Grove, 1852), vacuum arc deposition ("deflagration," Faraday, 1857), plasma-enhanced CVD (Barthelot, 1869) and evaporation (Stefan, Hertz, and Knudsen, 1873-1915) all had to wait for the invention of vacuum pumps whose history ranges from ˜1650 for mechanical pumps, through ˜1865 for mercury pumps that produce ballistic pressures in small systems. The development of crystallography, beginning with Plato in 360 BC, Kepler in 1611, and leading to Miller indices (1839) for describing orientation and epitaxial relationships in modern thin film technology, was already well advanced by the 1780s (Haüy). The starting point for the development of heterogeneous thin film nucleation theory was provided by Young in 1805. While an historical timeline tracing the progress of thin film technology is interesting of itself, the stories behind these developments are even more fascinating and provide insight into the evolution of scientific reasoning.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yakubovich, O. V., E-mail: yakubol@geol.msu.ru; Biralo, G. V.; Dimitrova, O. V.

The crystal structure of the (Al,V){sub 4}(P{sub 4}O{sub 12}){sub 3} solid solution, obtained in the single-crystal form by hydrothermal synthesis in the Al(OH){sub 3}-VO{sub 2}-NaCl-H{sub 3}PO{sub 4}-H{sub 2}O system, has been solved by X-ray diffraction analysis (Xcalibur-S-CCD diffractometer, R = 0.0257): a = 13.7477(2) Angstrom-Sign , sp. gr. I 4 bar 3d, Z = 4, and {rho}{sub calcd} = 2.736 g/cm{sup 3}. It is shown that the crystal structure of the parent cubic Al{sub 4}(P{sub 4}O{sub 12}){sub 3} modification can formally be considered an archetype for the formation of double isosymmetric tetraphosphates on its basis.

25-Hydroxyvitamin D response to graded vitamin D₃ supplementation among obese adults.

PubMed

Drincic, Andjela; Fuller, Eileen; Heaney, Robert P; Armas, Laura A G

2013-12-01

Guidelines have suggested that obese adults need 2 to 3 times more vitamin D than lean adults to treat vitamin D deficiency, but few studies have evaluated the vitamin D dose response in obese subjects. The purpose of this study was to characterize the pharmacokinetics of 25-hydroxyvitamin D [25(OH)D] response to 3 different doses of vitamin D₃ (cholecalciferol) in a group of obese subjects and to quantify the 25(OH)D dose-response relationship. DESIGN, SETTING, INTERVENTION, PATIENTS: This was a randomized, single-blind study of 3 doses of oral vitamin D₃ (1000, 5000, or 10,000 IU) given daily to 67 obese subjects for 21 weeks during the winter months. Serum 25(OH)D levels were measured at baseline and after vitamin D replacement, and 25(OH)D pharmacokinetic parameters were determined, fitting the 25(OH)D concentrations to an exponential model. Mean measured increments in 25(OH)D at week 21 were 12.4 ± 9.7 ng/mL in the 1000 IU/d group, 27.8 ± 10.2 ng/mL in the 5000 IU/d group, and 48.1 ± 19.6 ng/mL in the 10,000 IU/d group. Steady-state increments computed from the model were 20.6 ± 17.1, 35.2 ± 14.6, and 51.3 ± 22.0 ng/mL, respectively. There were no hypercalcuria or hypercalcemia events during the study. Our data show that in obese people, the 25(OH)D response to vitamin D₃ is directly related to dose and body size with ∼2.5 IU/kg required for every unit increment in 25(OH)D (nanograms per milliliter).

Whole Brain Networks for Treatment for Epilepsy

DTIC Science & Technology

2012-07-01

target. For the numerical approach, we applied both a simultaneous over- relaxation method (e.g. Gauss - Seidel ) and a biconjugate gradient...with b=1000sec/mm 2 and 7 b=0 acquisitions) was acquired on a Siemens TIM Trio (Siemens Medical Solutions, Erlangen) followed by iterative motion...partly from the difficulty with which the Monte Carlo approach is able to determine track densities at regions distal to the seed. Much iteration is

Development of a Measurement and Control System for a 40l/h Helium Liquefier based on Siemens PLC S7-300

NASA Astrophysics Data System (ADS)

Li, J.; Liu, L. Q.; Xu, X. D.; Liu, T.; Li, Q.; Hu, Z. J.; Wang, B. M.; Xiong, L. Y.; Dong, B.; Yan, T.

A 40l/h Helium Liquefier has been commissioned by the Technical Institute of Physics and Chemistry, Chinese Academy of Sciences. A measurement and control system based on Siemens PLC S7-300 for this Helium Liquefier is developed. Proper sensors are selected, for example, three types of transmitters are adopted respectively according to detailed temperature measurement requirements. Siemens S7-300 PLC CPU315-2PN/DP operates as a master station and three sets of ET200 M DP remote expand I/O operate asslave stations. Profibus-DP field communication is used between the master station and the slave stations. The upper computer HMI(Human Machine Interface) is compiled using Siemens configuration software WinCC V7.0. The upper computer communicates with PLC by means of industrial Ethernet. A specific control logic for this Helium Liquefier is developed. The control of the suction and discharge pressures of the compressor and the control of the turbo-expanders loop are being discussed in this paper. Following the commissioning phase, the outlet temperature of the second stage turbine has reached 8.6K and the temperature before the throttle valve has reached 13.1K.

Measurement and control system for cryogenic helium gas bearing turbo-expander experimental platform based on Siemens PLC S7-300

NASA Astrophysics Data System (ADS)

Li, J.; Xiong, L. Y.; Peng, N.; Dong, B.; Wang, P.; Liu, L. Q.

2014-01-01

An experimental platform for cryogenic Helium gas bearing turbo-expanders is established at the Technical Institute of Physics and Chemistry, Chinese Academy of Sciences. This turbo-expander experimental platform is designed for performance testing and experimental research on Helium turbo-expanders with different sizes from the liquid hydrogen temperature to the room temperature region. A measurement and control system based on Siemens PLC S7-300 for this turbo-expander experimental platform is developed. Proper sensors are selected to measure such parameters as temperature, pressure, rotation speed and air flow rate. All the collected data to be processed are transformed and transmitted to S7-300 CPU. Siemens S7-300 series PLC CPU315-2PN/DP is as master station and two sets of ET200M DP remote expand I/O is as slave station. Profibus-DP field communication is established between master station and slave stations. The upper computer Human Machine Interface (HMI) is compiled using Siemens configuration software WinCC V6.2. The upper computer communicates with PLC by means of industrial Ethernet. Centralized monitoring and distributed control is achieved. Experimental results show that this measurement and control system has fulfilled the test requirement for the turbo-expander experimental platform.

Ecdysteroid-stimulated synthesis and secretion of an N-acetyl-D-glucosamine-rich glycopeptide in a lepidopteran cell line derived from imaginal discs.

PubMed

Porcheron, P; Morinière, M; Coudouel, N; Oberlander, H

1991-01-01

Hormone-regulated processing of N-acetyl-D-glucosamine was studied in an insect cell line derived from imaginal wing discs of the Indian meal moth, Plodia interpunctella (Hübner). The cell line, IAL-PID2, responded to treatment with 20-hydroxyecdysone with increased incorporation of GlcNAc into glycoproteins. Cycloheximide and tunicamycin counteracted the action of the hormone. In particular, treatment with 20-hydroxyecdysone resulted in the secretion of a 5,000 dalton N-acetyl-D-glucosamine-rich glycopeptide by the IAL-PID2 cells. Accumulation of this peptide was prevented by the use of teflubenzuron, a potent chitin synthesis inhibitor. A glycopeptide of similar molecular weight was observed in imaginal discs of P. interpunctella treated with 20-hydroxyecdysone in vitro, under conditions that induce chitin synthesis. Although the function of the 5,000 dalton glycopeptide is not known, we believe that the PID2 cell line is a promising model for molecular analysis of ecdysteroid-regulated processing of aminosugars by epidermal cells during insect development.

SU-D-201-01: Attenuation of PET/CT Gantries with 511 KeV Photons

DOE Office of Scientific and Technical Information (OSTI.GOV)

Busse, N

2015-06-15

Purpose: PET shielding requires the use of large amounts of lead because of the penetrating nature of 511 keV photons. While the uptake rooms generally require the thickest lead, the scan room often requires substantial shielding. Attenuation by the PET/CT gantry is normally assumed to be zero, but may be significant in directions perpendicular to the scanner axis. Methods: A 5 mL tube was filled with between 14.7 and 20.5 mCi of F-18 and inserted into a phantom (70 cm NEMA PET Scatter Phantom). Exposure rates were recorded at several distances and 15° intervals with a pressurized ionization chamber (Ludlummore » 9DP) both with the phantom outside the gantry and centered in the CT and PET acquisition positions. These measurements were repeated with three scanners: Siemens Biograph TruePoint 6, GE Optima 560, and Philips Gemini 64. Measurements were decay corrected and normalized to exposure rates outside the gantry to calculate percent transmission. Results: Between 45° to 135° (measured from the patient bed at 0°), average transmission was about 20% for GE, 35% for Philips, and 30% for Siemens. The CT gantry was roughly twice as attenuating as the PET gantry at 90° for all three manufacturers, with about 10% transmission through the CT gantry and 20% through the PET gantry. Conclusion: The Philips system is a split-gantry and therefore has a narrower angle of substantial attenuation. For the GE and Siemens systems, which are single-gantry design, transmission was relatively constant once the angle was sufficient to block line-of-sight from the phantom. While the patient may spend a greater fraction of time at the PET position of the scanner, transmission characteristics of the two components are similar enough to be treated collectively. For shielding angles between 45° and 135°, a reasonably conservative assumption would be to assume gantry transmission of 50%.« less

Oral intake of phenylbutyrate with or without vitamin D3 upregulates the cathelicidin LL-37 in human macrophages: a dose finding study for treatment of tuberculosis

PubMed Central

2013-01-01

Background We earlier showed that 4-phenylbutyrate (PB) can induce cathelicidin LL-37 expression synergistically with 1,25-dihydroxyvitamin D3 in a lung epithelial cell line. We aimed to evaluate a therapeutic dose of PB alone or in combination with vitamin D3 for induction of LL-37 expression in immune cells and enhancement of antimycobacterial activity in monocyte-derived macrophages (MDM). Methods Healthy volunteers were enrolled in an 8-days open trial with three doses of PB [250 mg (Group-I), 500 mg (Group-II) or 1000 mg (Group-III)] twice daily (b.d.) together with vitamin D3 {5000 IU once daily (o.d.)}, PB (500 mg b.d.) (Group-IV) or vitamin D3 (5000 IU o.d.) (Group-V), given orally for 4 days. Blood was collected on day-0, day-4 and day-8; plasma was separated, peripheral blood mononuclear cells (PBMC), non-adherent lymphocytes (NAL) and MDM were cultured. LL-37 transcript in cells and peptide concentrations in supernatant were determined by qPCR and ELISA, respectively. In plasma, 25-hydorxyvitamin D3 levels were determined by ELISA. MDM-mediated killing of Mycobacterium tuberculosis (Mtb) (H37Rv) was performed by conventional culture method. Results MDM from Group-II had increased concentration of LL-37 peptide and transcript at day-4, while Group-I showed increased transcript at day-4 and day-8 compared to day-0 (p < 0.05). Both Group-I and -II exhibited higher levels of transcript on day-4 compared to Group-III and Group-V (p < 0.035). Increased induction of peptide was observed in lymphocytes from Group-II on day-4 compared to Group-I and Group-IV (p < 0.05), while Group-IV showed increased levels on day-8 compared to Group-I and Group-III (p < 0.04). Intracellular killing of Mtb on day-4 was significantly increased compared to day-0 in Group-I, -II and -V (p < 0.05). Conclusion The results demonstrate that 500 mg b.d. PB with 5000 IU o.d. vitamin D3 is the optimal dose for the induction of LL-37 in macrophages and lymphocytes and intracellular killing of Mtb by macrophages. Hence, this dose has potential application in the treatment of TB and is now being used in a clinical trial of adults with active pulmonary TB (NCT01580007). PMID:23590701

FPGAs and HPC

DTIC Science & Technology

2007-01-01

Ridge Technology, internal unpublished document. 10. Byoungro, S.; Diniz , P. C.; Hall, M. W. Using Estimates From Behavioral Synthesis Tools in...WIERSCHKE OLAC PL/RKFE 10 E SATURN BLVD EDWARDS AFB CA 93524-7680 1 NVL RSRCH LAB D PAPCONSTANTOPOULOS WASHINGTON DC 20375-5000 1

Experiments on planetary ices at UCL

NASA Astrophysics Data System (ADS)

Grindrod, P. M.; Fortes, A. D.; Wood, I. G.; Dobson, D.; Sammonds, P. R.; Stone-Drake, L.; Vocadlo, L.

2007-08-01

Using a suite of techniques and equipment, we conduct several different types of experiments on planetary ices at UCL. Samples are prepared in the Ice Physics Laboratory, which consists of a 5 chamber complex of inter-connected cold rooms, controllable from +30 to -30 deg C. Within this laboratory we have a functioning triaxial deformation cell operating at low temperature (down to -90 deg C) and high pressures (300 MPa), an Automatic Ice Fabric Analyser (AIFA) and a low-temperature microscope with CCD output. Polycrystalline samples, 40mm diameter by 100mm long, are compressed in the triaxial rig with a confining pressure; single crystal specimens are compressed in a separate uniaxial creep rig which operates at zero confining pressure for surface studies. A cold stage is also available for study of ice microstructural studies on our new Jeol JSM-6480LV SEM, which also allows tensile, compression and/or bending tests, with load ranges from less than 2N to 5000N. Finally, we also use a cold stage on a new PANalytical, X'pert PRO MPD, high resolution powder diffractometer to study the structure and phase behaviour of icy materials. Recent highlights of our work include: (1) derivation of a manufacturing process for methane clathrate at low temperatures, analysed in the X-Ray Diffraction Laboratory, for future rheological experiments, (2) analysed the growth behaviour of MS11, (3) refurbished and commenced calibration tests on the triaxial deformation cell using ice Ih, and (4) performed creep tests on gypsum and epsomite using the single crystal deformation cell. Further experiments will build on these preliminary results.

A Novel X-ray Diffractometer for the Florida Split Coil 25 Tesla Magnet

NASA Astrophysics Data System (ADS)

Wang, Shengyu; Kovalev, Alexey; Suslov, Alexey; Siegrist, Theo

2014-03-01

At National High Magnetic Field Laboratory (NHMFL), we are developing a unique X-ray diffractometer for the 25 Tesla Florida Split Coil Magnet for scattering experiments under extremely high static magnetic fields. The X-ray source is a sealed tube (copper or molybdenum anode), connected to the magnet by an evacuated beam tunnel. The detectors are either an image plate or a silicon drift detector, with the data acquisition system based on LabVIEW. Our preliminary experimental results showed that the performance of the detector electronics and the X-ray generator is reliable in the fringe magnetic fields produced at the highest field of 25 T. Using this diffractometer, we will make measurements on standard samples, such as LaB6, Al2O3 and Si, to calibrate the diffraction system. Magnetic samples, such as single crystal HoMnO3 and stainless steel 301 alloys will be measured subsequently. The addition of X-ray diffraction to the unique split coil magnet will significantly expand the NHMFL experimental capabilities. Therefore, external users will be able to probe spin - lattice interactions at static magnetic fields up to 25T. This project is supported by NSF-DMR Award No.1257649. NHMFL is supported by NSF Cooperative Agreement No. DMR-1157490, the State of Florida, and the U.S. DoE.

Ab initio simulation of diffractometer instrumental function for high-resolution X-ray diffraction1

PubMed Central

Mikhalychev, Alexander; Benediktovitch, Andrei; Ulyanenkova, Tatjana; Ulyanenkov, Alex

2015-01-01

Modeling of the X-ray diffractometer instrumental function for a given optics configuration is important both for planning experiments and for the analysis of measured data. A fast and universal method for instrumental function simulation, suitable for fully automated computer realization and describing both coplanar and noncoplanar measurement geometries for any combination of X-ray optical elements, is proposed. The method can be identified as semi-analytical backward ray tracing and is based on the calculation of a detected signal as an integral of X-ray intensities for all the rays reaching the detector. The high speed of calculation is provided by the expressions for analytical integration over the spatial coordinates that describe the detection point. Consideration of the three-dimensional propagation of rays without restriction to the diffraction plane provides the applicability of the method for noncoplanar geometry and the accuracy for characterization of the signal from a two-dimensional detector. The correctness of the simulation algorithm is checked in the following two ways: by verifying the consistency of the calculated data with the patterns expected for certain simple limiting cases and by comparing measured reciprocal-space maps with the corresponding maps simulated by the proposed method for the same diffractometer configurations. Both kinds of tests demonstrate the agreement of the simulated instrumental function shape with the measured data. PMID:26089760

Precision Positioning and Inertial Guidance Sensors. Technology and Operational Aspects

DTIC Science & Technology

1981-03-01

Ueberlingen, GE EVALUATION D’UN SYSTEME EUROPEEN DE NAVIGATION HYBRIDE A - - GYROLASER POUR HELICOPTERE: "SEXTAN" by D Regnault, Centre d’Essais en Vol de...NAVIGATION SYSTEM AND STANDARD STATE ELEMENT DEVIATIONMEASUREMENT SOURCES( Dead-reckoning with position fxP fy 5000 En ]TAS, heading and wind scale...Reproduction Ltd ilarford House. 7-9 Charlotte St. London. WIP JIHD [i Ii THEME A new class of precision positioning systems , including GPS (Global

Calculations of two new dose metrics proposed by AAPM Task Group 111 using the measurements with standard CT dosimetry phantoms

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Xinhua; Zhang, Da; Liu, Bob

2013-08-15

Purpose: AAPM Task Group 111 proposed to measure the equilibrium dose-pitch product D-caret{sub eq} for scan modes involving table translation and the midpoint dose D{sub L}(0) for stationary-table modes on the central and peripheral axes of sufficiently long (e.g., at least 40 cm) phantoms. This paper presents an alternative approach to calculate both metrics using the measurements of scanning the standard computed tomographic (CT) dosimetry phantoms on CT scanners.Methods: D-caret{sub eq} was calculated from CTDI{sub 100} and ε(CTDI{sub 100}) (CTDI{sub 100} efficiency), and D{sub L}(0) was calculated from D-caret{sub eq} and the approach to equilibrium function H(L) =D{sub L}(0)/D{sub eq},more » where D{sub eq} was the equilibrium dose. CTDI{sub 100} may be directly obtained from several sources (such as medical physicist's CT scanner performance evaluation or the IMPACT CT patient dosimetry calculator), or be derived from CTDI{sub Vol} using the central to peripheral CTDI{sub 100} ratio (R{sub 100}). The authors have provided the required ε(CTDI{sub 100}) and H(L) data in two previous papers [X. Li, D. Zhang, and B. Liu, Med. Phys. 39, 901–905 (2012); and ibid. 40, 031903 (10pp.) (2013)]. R{sub 100} was assessed for a series of GE, Siemens, Philips, and Toshiba CT scanners with multiple settings of scan field of view, tube voltage, and bowtie filter.Results: The calculated D{sub L}(0) and D{sub L}(0)/D{sub eq} in PMMA and water cylinders were consistent with the measurements on two GE CT scanners (LightSpeed 16 and VCT) by Dixon and Ballard [Med. Phys. 34, 3399–3413 (2007)], the measurements on a Siemens CT scanner (SOMATOM Spirit Power) by Descamps et al. [J. Appl. Clin. Med. Phys. 13, 293–302 (2012)], and the Monte Carlo simulations by Boone [Med. Phys. 36, 4547–4554 (2009)].Conclusions: D-caret{sub eq} and D{sub L}(0) can be calculated using the alternative approach. The authors have provided the required ε(CTDI{sub 100}) and H(L) data in two previous papers. R{sub 100} is presented for a majority of multidetector CT scanners currently on the market, and can be easily assessed for other CT scanners or operating conditions not covered in this study. The central to peripheral D{sub eq} ratio is about 1.50 and 1.12 times of R{sub 100} for the 32- and 16-cm diameter PMMA phantom, respectively.« less

Versatile, immersive, creative and dynamic virtual 3-D healthcare learning environments: a review of the literature.

PubMed

Hansen, Margaret M

2008-09-01

The author provides a critical overview of three-dimensional (3-D) virtual worlds and "serious gaming" that are currently being developed and used in healthcare professional education and medicine. The relevance of this e-learning innovation for teaching students and professionals is debatable and variables influencing adoption, such as increased knowledge, self-directed learning, and peer collaboration, by academics, healthcare professionals, and business executives are examined while looking at various Web 2.0/3.0 applications. There is a need for more empirical research in order to unearth the pedagogical outcomes and advantages associated with this e-learning technology. A brief description of Roger's Diffusion of Innovations Theory and Siemens' Connectivism Theory for today's learners is presented as potential underlying pedagogical tenets to support the use of virtual 3-D learning environments in higher education and healthcare.

Implementation of Siemens USS protocol into LabVIEW.

PubMed

Hosek, P; Diblik, M

2011-10-01

This article gives basic overview of the USS protocol as a communication interface to drive Siemens frequency inverters. It presents our implementation of this protocol into LabVIEW, as there was permanent demand from the community of the users to have native LabVIEW implementation of the USS protocol. It also states encountered problems and their solutions. Copyright © 2011 Society for Laboratory Automation and Screening. Published by Elsevier Inc. All rights reserved.

Digital SPC Switching Technology--Foreign Technology Assessment

DTIC Science & Technology

1990-12-01

India C DOT MAX C DOT DSS 0 TDX 1 Samsung , Goldstar Korea TDX 10 Daewoo, Otelco (ROK) System X Plessey/GEC U.K. (Siemens) Fetex 150 Fujitsu Japan HDX...x South Korea Alcatel ATT Malaysia Ericsson NEC New Zealand NEC Philippines DAEWOO Siemens Singapore Fujitsu (AU-, NEC Gateway Switches) Taiwan...Yes Israel Northern Telecom DMS 10 Telrad Yes OMS 100 * Malaysia Ericsson AXE Pewira Ericsson Future SDN BHD Mexico Alcatel System 12 Indetel No

30 CFR Appendix I to Subpart D of... - Appendix I to Subpart D of Part 18

Code of Federal Regulations, 2011 CFR

2011-07-01

... diameter of three-conductor portable power cables with tolerances in inches—601 to 5,000 volts. 8 Fuse... diameters. Table 1—Portable Power Cable Ampacities—600 Volts (Amperes Per Conductor Based on 60 °C. Copper Temperature—40 °C. Ambient) Conductor size—AWG or MCM Single conductor 2-conductor, round or flat 3-conductor...

30 CFR Appendix I to Subpart D of... - Appendix I to Subpart D of Part 18

Code of Federal Regulations, 2010 CFR

2010-07-01

... diameter of three-conductor portable power cables with tolerances in inches—601 to 5,000 volts. 8 Fuse... diameters. Table 1—Portable Power Cable Ampacities—600 Volts (Amperes Per Conductor Based on 60 °C. Copper Temperature—40 °C. Ambient) Conductor size—AWG or MCM Single conductor 2-conductor, round or flat 3-conductor...

Remote analysis of planetary soils: X-ray diffractometer development

NASA Technical Reports Server (NTRS)

Gregory, J. C.

1973-01-01

A system is described suitable for remote low power mineralogical analysis of lunar, planetary, or asteroid soils. It includes an X-ray diffractometer, fluorescence spectrometer, and sample preparation system. A one Curie Fe-55 source provides a monochromatic X-ray beam of 5.9 keV. Seeman-Bohlin or focusing geometry is employed in the camera, allowing peak detection to proceed simultaneously at all angles and obviating the need for moving parts. The detector system is an array of 500-600 proportional counters with a wire-spacing of 1 mm. An electronics unit comprising preamplifier, postamplifier, window discriminators, and storage flipflops requiring only 3.5 milliwatts was designed and tested. Total instrument power is less than 5 watts. Powder diffraction patterns using a flat breadboard multiwire counter were recorded.

Toward a Capability Engineering Process

DTIC Science & Technology

2004-12-01

TOWARD A CAPABILITY ENGINEERING PROCESS M. Lizotte, F. Bernier, M. Mokhtari , M. Couture, G. Dussault, C. Lalancette, F. Lemieux System of Systems...Lizotte, F. Lemieux, the US DoD 5000 acquisition strategies?; and (8) since a M. Mokhtari , 2004: Toward Capability Engineering capability can be

TU-EF-204-01: Accurate Prediction of CT Tube Current Modulation: Estimating Tube Current Modulation Schemes for Voxelized Patient Models Used in Monte Carlo Simulations

DOE Office of Scientific and Technical Information (OSTI.GOV)

McMillan, K; Bostani, M; McNitt-Gray, M

2015-06-15

Purpose: Most patient models used in Monte Carlo-based estimates of CT dose, including computational phantoms, do not have tube current modulation (TCM) data associated with them. While not a problem for fixed tube current simulations, this is a limitation when modeling the effects of TCM. Therefore, the purpose of this work was to develop and validate methods to estimate TCM schemes for any voxelized patient model. Methods: For 10 patients who received clinically-indicated chest (n=5) and abdomen/pelvis (n=5) scans on a Siemens CT scanner, both CT localizer radiograph (“topogram”) and image data were collected. Methods were devised to estimate themore » complete x-y-z TCM scheme using patient attenuation data: (a) available in the Siemens CT localizer radiograph/topogram itself (“actual-topo”) and (b) from a simulated topogram (“sim-topo”) derived from a projection of the image data. For comparison, the actual TCM scheme was extracted from the projection data of each patient. For validation, Monte Carlo simulations were performed using each TCM scheme to estimate dose to the lungs (chest scans) and liver (abdomen/pelvis scans). Organ doses from simulations using the actual TCM were compared to those using each of the estimated TCM methods (“actual-topo” and “sim-topo”). Results: For chest scans, the average differences between doses estimated using actual TCM schemes and estimated TCM schemes (“actual-topo” and “sim-topo”) were 3.70% and 4.98%, respectively. For abdomen/pelvis scans, the average differences were 5.55% and 6.97%, respectively. Conclusion: Strong agreement between doses estimated using actual and estimated TCM schemes validates the methods for simulating Siemens topograms and converting attenuation data into TCM schemes. This indicates that the methods developed in this work can be used to accurately estimate TCM schemes for any patient model or computational phantom, whether a CT localizer radiograph is available or not. Funding Support: NIH Grant R01-EB017095; Disclosures - Michael McNitt-Gray: Institutional Research Agreement, Siemens AG; Research Support, Siemens AG; Consultant, Flaherty Sensabaugh Bonasso PLLC; Consultant, Fulbright and Jaworski; Disclosures - Cynthia McCollough: Research Grant, Siemens Healthcare.« less

Microwave Absorption Properties of La0.8Ca0.2-xAgxMnO3 (x=0.05; x=0.15) Synthesized by Sol-Gel Method

NASA Astrophysics Data System (ADS)

Kurniawan, B.; Laksmi, W.; Sahara, N. A.

2018-04-01

Microwave absorption properties of La0.8Ca0.2-xAgxMnO3 (x= 0.05; 0.15) is reported in this paper. Lanthanum manganite materials was reported as a potential absorber material [1][2][3]. In this paper, the material was synthesized by sol-gel method, calcined at 550°C, and sintered at 900°C. The material was characterized by X-Ray Diffractometer (XRD), and we found that the materials were single phased. Through SEM-EDS characterization it is found that the materials have compositional purity. The resistivity of the materials is obtained by four point probe method, and it is shown that Ag doped decreases the resistivity of the materials. Reflection loss of La0.8Ca0.15Ag0.05MnO3 reaches -4.470 dB and La0.8Ca0.05Ag0.15MnO3 reaches - 7.953 dB.

SU-F-J-117: Impact of Motion Artifacts On Image Quality and Accuracy of Tumor Motion Reconstruction in 4D CT-On-Rails and MV-CBCT Scans: A Phantom Study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lin, T; Ma, C

Purpose: To compare and quantify respiratory motion artifacts in images from free breathing 4D-CT-on-Rails(CTOR) and those from MV-Cone-beam-CT(MVCB) and facilitate respiratory motion guided radiation therapy. Methods: 4D-CTOR: Siemens Somatom CT-on-Rails system with Anzai belt loaded with pressure sensor load cells. 4D scans were performed in helical mode, pitch 0.1, gantry rotation time 0.5s, 1.5mm slice thickness, 120kVp, 400 mAs. Normal and fast breathing (>12rpm) scanning protocols were investigated. Helical scan, AIP(average intensity projection) and MIP(maximum intensity projection) were generated from 4D-CTOR scans with amplitude sorting into 10 phases.MVCB: Siemens Artiste diamond view(1MV)MVCB was performed with 5MU thorax protocol with 60more » second of full rotation.Phantom: Anzai AZ-733V respiratory phantom. The settings were set to normal and resp. modes with repetition rates at 15 rpm and 10 rpm. Surgical clips, acrylic, wooden, rubber and lung density, total six mock-ups were scanned and compared in this study.Signal-to-noise ratio(SNR), contrast-to-noise ratio(CNR) and reconstructed motion volume were compared to different respiratory setups for the mock-ups. Results: Reconstructed motion volume was compared to the real object volume for the six test mock-ups. It shows that free breathing helical in all instances underestimates the object excursions largest to −67.4% and least −6.3%. Under normal breathing settings, MIP can predict very precise motion volume with minimum 0.4% and largest −13.9%. MVCB shows underestimate of the motion volume with −1.11% minimum and −18.0% maximum. With fast breathing, AIP provides bad representation of the object motion; however, the MIP can predict the motion volume with −2.0% to −11.4% underestimate. Conclusion: Respiratory motion guided radiation therapy requires good motion recording. This study shows that regular CTOR helical scans provides bad guidance, 4D CTOR AIP cannot represent the fast breathing pattern, MIP can represent the best motion volume, MVCBCT can only be used for normal breathing with acceptable uncertainties.« less

Aging of D-limonene-cleaned assemblies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Somer, T.A.

1994-04-01

The performance of 2000 electronic circuit variables was monitored throughout a 5000-hour exposure to + 160{degrees}F. the 2000 variables involve 36 electronic assemblies, cleaned with various solvents, including d-limonene, as a replacement for TCE. The assemblies were divided into four groups, including a TCE-cleaned control group at room temperature. Of the three groups exposed at + 160{degrees}F, one was cleaned in TCE, one was cleaned in d-limonene, and one was kept in a saturated d-limonene atmosphere. No performance degradation was observed with any of the groups, including the worst case exposure in a saturated d-limonene atmosphere.

Characteristics of step-defined physical activity categories in U.S. adults..

PubMed

Sisson, Susan B; Camhi, Sarah M; Tudor-Locke, Catrine; Johnson, William D; Katzmarzyk, Peter T

2012-01-01

Descriptive physical activity epidemiology of the U.S. population is critical for program development and resource allocation. The purpose of this project was to describe step-defined categories (as measured by accelerometer) of U.S. adults and to determine predictors of sedentary classification (<5000 steps/d). The National Health and Nutrition Examination Survey (NHANES) is an annual, nationally representative survey used to determine the health status of the U.S. populace. In-home interviews and physical examination components of NHANES. Overall, 4372 eligible adults wore accelerometers in the 2005-2006 NHANES; 628 were excluded, which yielded 3744 adults (of which 46.8% were men). Steps per day; body mass index (BMI); demographic, household and behavioral variables. Means and frequencies were calculated. Logistic regression was utilized to determine predictors of sedentary classification. Overall, 36.1% were sedentary (i.e., <5000 steps/d); 47.6% were low to somewhat active (5000-9999 steps/d); 16.3% were active to highly active (≥10,000 steps/d). Advancing age (odds ratio [OR], 1.95; confidence intervals [CIs], 1.78, 2.13), higher BMI (OR, 1.40; CIs, 1.23, 1.59), female sex (OR, 1.86; CIs, 1.46, 2.36), African-American versus European-American ethnicity (OR, 1.36; CIs, 1.13, 1.65), household income versus ≥$45,000 (<$25,000: OR, 1.94; CIs, 1.40, 2.69; $25,000-$44,000: OR, 1.51; CIs, 1.23, 1.85), and current versus never smoker (OR, 1.53; CIs, 1.26, 1.86) variables had higher odds of sedentary classification. Usual daily occupational/domestic physical activity categories of standing/walking (OR, .51; CIs, .38, .69); lifting/climbing (OR, .26; CIs, .17, .38); and heavy loads/labor (OR, .16; CIs, .10, .26) had lower odds of sedentary classification than sitting. Over one-third of the U.S. population was classified as sedentary by accelerometer-determined steps per day, and several characteristics predicted sedentary classification.

Evolutionary genomics of peach and almond domestication

USDA-ARS?s Scientific Manuscript database

The domesticated almond [Prunus dulcis (L.) Batsch] and peach [P. persica (Mill.) D. A. Webb] originate on opposite sides of Asia and were independently domesticated approximately 5000 years ago. While interfertile, they possess alternate mating systems and di er in a number of morphological and ph...

26 CFR 1.7519-1T - Required payments for entities electing not to have required year (temporary).

Code of Federal Regulations, 2011 CFR

2011-04-01

.... Example 1. D, a partnership, is owned 10 percent by a C corporation with a September 30 taxable year and... $10,000 are deductible during the deferral period of the base year. Based on these facts, D has net... year $10,000 $5,000 Net base year income $40,000 Example 4. E is a C corporation that has historically...

Aldh2 knockout mice were more sensitive to DNA damage in leukocytes due to ethyl tertiary butyl ether exposure.

PubMed

Weng, Zuquan; Suda, Megumi; Ohtani, Katsumi; Mei, Nan; Kawamoto, Toshihiro; Nakajima, Tamie; Wang, Rui-Sheng

2011-01-01

To clarify the genotoxicity of ethyl tertiary butyl ether (ETBE), a gasoline additive, male and female C57BL/6 mice of Aldh2+/+ and Aldh2-/- genotypes, aged 8 wk, were exposed to 0, 500, 1,750, or 5,000 ppm ETBE for 6 h/day, 5 d per week for 13 wk. DNA damage in leukocytes was measured by the alkaline comet assay and expressed quantitatively as Tail Intensity (TI). For male mice, TI was significantly higher in all three groups exposed to ETBE than in those without exposure within Aldh2-/- mice, whereas within Aldh2+/+ mice, TI increased only in those exposed to 5,000 ppm of ETBE as compared with mice without exposure. For female mice, a significant increase in TI values was observed in the group exposed to 5,000 ppm of ETBE as compared with those without exposure within Aldh2-/- mice; TI in Aldh2-/- mice exposed to 1,750 and 5,000 ppm was significantly higher than in Aldh2+/+ mice without exposure. TI did not significantly increase in any of the groups exposed to ETBE within female Aldh2+/+ mice. Based on the results we suggest that Aldh2-/- mice are more sensitive to DNA damage caused by ETBE than Aldh2+/+ mice and that males seem more susceptible to this effect than females.

Two examples of indication specific radiation dose calculations in dental CBCT and Multidetector CT scanners.

PubMed

Stratis, Andreas; Zhang, Guozhi; Lopez-Rendon, Xochitl; Politis, Constantinus; Hermans, Robert; Jacobs, Reinhilde; Bogaerts, Ria; Shaheen, Eman; Bosmans, Hilde

2017-09-01

To calculate organ doses and estimate the effective dose for justification purposes in patients undergoing orthognathic treatment planning purposes and temporal bone imaging in dental cone beam CT (CBCT) and Multidetector CT (MDCT) scanners. The radiation dose to the ICRP reference male voxel phantom was calculated for dedicated orthognathic treatment planning acquisitions via Monte Carlo simulations in two dental CBCT scanners, Promax 3D Max (Planmeca, FI) and NewTom VGi evo (QR s.r.l, IT) and in Somatom Definition Flash (Siemens, DE) MDCT scanner. For temporal bone imaging, radiation doses were calculated via MC simulations for a CBCT protocol in NewTom 5G (QR s.r.l, IT) and with the use of a software tool (CT-expo) for Somatom Force (Siemens, DE). All procedures had been optimized at the acceptance tests of the devices. For orthognathic protocols, dental CBCT scanners deliver lower doses compared to MDCT scanners. The estimated effective dose (ED) was 0.32mSv for a normal resolution operation mode in Promax 3D Max, 0.27mSv in VGi-evo and 1.18mSv in the Somatom Definition Flash. For temporal bone protocols, the Somatom Force resulted in an estimated ED of 0.28mSv while for NewTom 5G the ED was 0.31 and 0.22mSv for monolateral and bilateral imaging respectively. Two clinical exams which are carried out with both a CBCT or a MDCT scanner were compared in terms of radiation dose. Dental CBCT scanners deliver lower doses for orthognathic patients whereas for temporal bone procedures the doses were similar. Copyright © 2017 Associazione Italiana di Fisica Medica. Published by Elsevier Ltd. All rights reserved.

Single-source dual-energy computed tomography: use of monoenergetic extrapolation for a reduction of metal artifacts.

PubMed

Mangold, Stefanie; Gatidis, Sergios; Luz, Oliver; König, Benjamin; Schabel, Christoph; Bongers, Malte N; Flohr, Thomas G; Claussen, Claus D; Thomas, Christoph

2014-12-01

The objective of this study was to retrospectively determine the potential of virtual monoenergetic (ME) reconstructions for a reduction of metal artifacts using a new-generation single-source computed tomographic (CT) scanner. The ethics committee of our institution approved this retrospective study with a waiver of the need for informed consent. A total of 50 consecutive patients (29 men and 21 women; mean [SD] age, 51.3 [16.7] years) with metal implants after osteosynthetic fracture treatment who had been examined using a single-source CT scanner (SOMATOM Definition Edge; Siemens Healthcare, Forchheim, Germany; consecutive dual-energy mode with 140 kV/80 kV) were selected. Using commercially available postprocessing software (syngo Dual Energy; Siemens AG), virtual ME data sets with extrapolated energy of 130 keV were generated (medium smooth convolution kernel D30) and compared with standard polyenergetic images reconstructed with a B30 (medium smooth) and a B70 (sharp) kernel. For quantification of the beam hardening artifacts, CT values were measured on circular lines surrounding bone and the osteosynthetic device, and frequency analyses of these values were performed using discrete Fourier transform. A high proportion of low frequencies to the spectrum indicates a high level of metal artifacts. The measurements in all data sets were compared using the Wilcoxon signed rank test. The virtual ME images with extrapolated energy of 130 keV showed significantly lower contribution of low frequencies after the Fourier transform compared with any polyenergetic data set reconstructed with D30, B70, and B30 kernels (P < 0.001). Sequential single-source dual-energy CT allows an efficient reduction of metal artifacts using high-energy ME extrapolation after osteosynthetic fracture treatment.

XCAT/DRASIM: a realistic CT/human-model simulation package

NASA Astrophysics Data System (ADS)

Fung, George S. K.; Stierstorfer, Karl; Segars, W. Paul; Taguchi, Katsuyuki; Flohr, Thomas G.; Tsui, Benjamin M. W.

2011-03-01

The aim of this research is to develop a complete CT/human-model simulation package by integrating the 4D eXtended CArdiac-Torso (XCAT) phantom, a computer generated NURBS surface based phantom that provides a realistic model of human anatomy and respiratory and cardiac motions, and the DRASIM (Siemens Healthcare) CT-data simulation program. Unlike other CT simulation tools which are based on simple mathematical primitives or voxelized phantoms, this new simulation package has the advantages of utilizing a realistic model of human anatomy and physiological motions without voxelization and with accurate modeling of the characteristics of clinical Siemens CT systems. First, we incorporated the 4D XCAT anatomy and motion models into DRASIM by implementing a new library which consists of functions to read-in the NURBS surfaces of anatomical objects and their overlapping order and material properties in the XCAT phantom. Second, we incorporated an efficient ray-tracing algorithm for line integral calculation in DRASIM by computing the intersection points of the rays cast from the x-ray source to the detector elements through the NURBS surfaces of the multiple XCAT anatomical objects along the ray paths. Third, we evaluated the integrated simulation package by performing a number of sample simulations of multiple x-ray projections from different views followed by image reconstruction. The initial simulation results were found to be promising by qualitative evaluation. In conclusion, we have developed a unique CT/human-model simulation package which has great potential as a tool in the design and optimization of CT scanners, and the development of scanning protocols and image reconstruction methods for improving CT image quality and reducing radiation dose.

The effect of helium on ventilator performance: study of five ventilators and a bedside Pitot tube spirometer.

PubMed

Oppenheim-Eden, A; Cohen, Y; Weissman, C; Pizov, R

2001-08-01

To assess in vitro the performance of five mechanical ventilators-Siemens 300 and 900C (Siemens-Elma; Solna, Sweden), Puritan Bennett 7200 (Nellcor Puritan Bennett; Pleasanton, CA), Evita 4 (Dragerwerk; Lubeck, Germany), and Bear 1000 (Bear Medical Systems; Riverside CA)-and a bedside sidestream spirometer (Datex CS3 Respiratory Module; Datex-Ohmeda; Helsinki, Finland) during ventilation with helium-oxygen mixtures. In vitro study. ICUs of two university-affiliated hospitals. Each ventilator was connected to 100% helium through compressed air inlets and then tested at three to six different tidal volume (VT) settings using various helium-oxygen concentrations (fraction of inspired oxygen [FIO(2)] of 0.2 to 1.0). FIO(2) and VT were measured with the Datex CS3 spirometer, and VT was validated with a water-displacement spirometer. The Puritan Bennett 7200 ventilator did not function with helium. With the other four ventilators, delivered FIO(2) was lower than the set FIO(2). For the Siemens 300 and 900C ventilators, this difference could be explained by the lack of 21% oxygen when helium was connected to the air supply port, while for the other two ventilators, a nonlinear relation was found. The VT of the Siemens 300 ventilator was independent of helium concentration, while for the other three ventilators, delivered VT was greater than the set VT and was dependent on helium concentration. During ventilation with 80% helium and 20% oxygen, VT increased to 125% of set VT for the Siemens 900C ventilator, and more than doubled for the Evita 4 and Bear 1000 ventilators. Under the same conditions, the Datex CS3 spirometer underestimated the delivered VT by about 33%. At present, no mechanical ventilator is calibrated for use with helium. This investigation offers correction factors for four ventilators for ventilation with helium.

Piezoelectric Composite Micromachined Multifrequency Transducers for High-Resolution, High-Contrast Ultrasound Imaging for Improved Prostate Cancer Assessment

DTIC Science & Technology

2014-08-01

and in (b) a standard animal model of prostate cancer. In the preliminary in-vitro study , imaging resolution, contrast to tissue ratio, and lesion...detectability will be assessed relative to a Siemens EV- 8C4 transrectal ultrasound probe. In the in-vivo study , molecular imaging and microvascular...lesions will be imaged at several axial depths using our prototype array and the Siemens EV-8C4 clinical TRUS probe. A blinded reader study will be

A high-temperature neutron diffraction study of Nb 2AlC and TiNbAlC

DOE PAGES

Bentzel, Grady W.; Lane, Nina J.; Vogel, Sven C.; ...

2014-12-16

In this paper, we report on the crystal structures of Nb 2AlC and TiNbAlC actual composition (Ti 0.45,Nb 0.55) 2AlC compounds determined from Rietveld analysis of neutron diffraction patterns in the 300-1173 K temperature range. The average linear thermal expansion coefficients of a Nb 2AlC sample in the a and c directions are, respectively, 7.9(5)x10 -6 K -1 and 7.7(5)x10 -6 K -1 on one neutron diffractometer and 7.3(3)x10 -6 K -1 and 7.0(2)x10 -6 K -1 on a second diffractometer. The respective values for the (Ti 0.45,Nb 0.55) 2AlC composition - only tested on one diffractometer - are 8.5(3)x10more » -6 K -1 and 7.5(5)x10 -6 K -1. These values are relatively low compared to other MAX phases. Like other MAX phases, however, the atomic displacement parameters show that the Al atoms vibrate with higher amplitudes than the Ti and C atoms, and 1 more along the basal planes than normal to them. In addition, when the predictions of the atomic displacement parameters obtained from density functional theory are compared to the experimental results, good quantitative agreement is found for the Al atoms. In case of the Nb and C atoms, the agreement was more qualitative.« less

New hardware and software platform for experiments on a HUBER-5042 X-ray diffractometer with a DISPLEX DE-202 helium cryostat in the temperature range of 20-300 K

NASA Astrophysics Data System (ADS)

Dudka, A. P.; Antipin, A. M.; Verin, I. A.

2017-09-01

Huber-5042 diffractometer with a closed-cycle Displex DE-202 helium cryostat is a unique scientific instrument for carrying out X-ray diffraction experiments when studying the single crystal structure in the temperature range of 20-300 K. To make the service life longer and develop new experimental techniques, the diffractometer control is transferred to a new hardware and software platform. To this end, a modern computer; a new detector reader unit; and new control interfaces for stepper motors, temperature controller, and cryostat vacuum pumping system are used. The system for cooling the X-ray tube, the high-voltage generator, and the helium compressor and pump for maintaining the desired vacuum in the cryostat are replaced. The system for controlling the primary beam shutter is upgraded. A biological shielding is installed. The new program tools, which use the Linux Ubuntu operating system and SPEC constructor, include a set of drivers for control units through the aforementioned interfaces. A program for searching reflections from a sample using fast continuous scanning and a priori information about crystal is written. Thus, the software package for carrying out the complete cycle of precise diffraction experiment (from determining the crystal unit cell to calculating the integral reflection intensities) is upgraded. High quality of the experimental data obtained on this equipment is confirmed in a number of studies in the temperature range from 20 to 300 K.

Acute and subchronic toxicity of naturally weathered Exxon Valdez crude oil in mallards and ferrets

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stubblefield, W.A.; Hancock, G.A.; Ford, W.H.

1995-11-01

The toxic properties of naturally weathered Exxon Valdez crude oil (WEVC) were assessed in a battery of acute and subchronic toxicity tests using mallards, Anas platyrhynchos, and European ferrets, Mustela putorius. Adult mallard acute oral toxicity study results indicated no mortalities or signs o toxicity, i.e., no-observed-adverse-effect level (NOAEL) and median lethal dose (LD50) > 5,000 mg/kg. Acute oral feeding and food avoidance tests with ducklings also indicated no toxicity (NOAEL and LC50 > 50,000 mg/kg diet) with no evidence of food avoidance (FAC50 > 20,000 mg/kg diet). No mortalities or toxic signs were noted in a 14-d feeding studymore » with adult birds at dietary concentrations up to 100,000 mg WEVC/kg diet. Among clinical and physiological end points evaluated, the only significant difference noted was an increase in liver: body weight ratios in the 100,000-mg WEVC/kg diet dose group. No differences in clinical chemistry or hematological parameters were noted, and there were no consistent differences in histological evaluations of organ tissues. Daily oral doses of up to 5,000 mg/kg of WEVC over 5 d resulted in minimal effects on ferrets. Increased serum albumin concentrations were observed in the 5,000-mg/kg dose group females and decreased spleen weights were noted in females of all WEVC treatment groups. No other significant observations were noted.« less

Economic feeder for recharging and ``topping off''

NASA Astrophysics Data System (ADS)

Fickett, Bryan; Mihalik, G.

2000-04-01

Increasing the size of the melt charge significantly increases yield and reduces costs. Siemens Solar Industries is optimizing a method to charge additional material after meltdown (top-off) using an external feeder system. A prototype feeder system was fabricated consisting of a hopper and feed delivery system. The low-cost feeder is designed for simple operation and maintenance. The system is capable of introducing up to 60 kg of granular silicon while under vacuum. An isolation valve permits refilling of the hopper while maintaining vacuum in the growth furnace. Using the feeder system in conjunction with Siemens Solar Industries' energy efficient hot zone dramatically reduces power and argon consumption. Throughput is also improved as faster pull speeds can be attained. The increased pull speeds have an even greater impact when the charge size is increased. Further cost reduction can be achieved by refilling the crucible after crystal growth and pulling a second ingot run. Siemens Solar Industries is presently testing the feeder in production.

Effects of exogenous proteases without or with carbohydrases on nutrient digestibility and disappearance of non-starch polysaccharides in broiler chickens

PubMed Central

Olukosi, O. A.; Beeson, L. A.; Englyst, K.; Romero, L. F.

2015-01-01

The objective of the current study was to evaluate the effect of a subtilisin protease, without or with inclusion of carbohydrases, on digestibility and retention of energy and protein, as well as the solubilization and disappearance of non-starch polysaccharides (NSP) from corn-soybean meal based diets fed to broiler chickens. Two hundred eighty-eight Ross 308 male broiler chickens were used for the experiment. On d 14, the birds were weighed and allocated to 6 treatments and 8 replicates per treatment with 6 birds per replicate. Treatments were: 1) corn-soybean meal based control diet; 2) control diet plus supplemental protease at 5,000 (P5000) protease units (PU)/kg); 3) control plus 10,000 PU/kg protease (P10000); or control plus an enzyme combination containing xylanase, amylase, and protease (XAP) added to achieve protease activity of: 4) 2,500 PU/kg (XAP2500); 5) 5,000 PU/kg (XAP5000); or 6) 10,000 PU/kg (XAP10000). The enzymes in XAP were combined at fixed ratios of 10:1:25 of xylanase:amylase:protease. Data were analyzed by ANOVA and specific orthogonal contrasts between treatments were performed. Addition of xylanase and amylase increased (P < 0.05) the ileal digestibility of protein by 4.2% and 2.1% at XAP5000 and XAP10000, respectively (relative to P5000 and P10000, respectively), exhibiting a plateau after the XAP5000 dose. Increment (P < 0.05) in AME due to protease was evident, particularly in P10000. At the ileal level, XAP reduced (P < 0.05) the flow of insoluble xylose and arabinose, which indicates an increase in the solubilization of arabinoxylan polymers in the small intestine. Protease on its own reduced (P < 0.05) the flow of insoluble arabinose but did not affect the flow of insoluble xylose. XAP reduced (P < 0.05) the pre-cecal flow of insoluble and total glucose and galactose. It was concluded that whereas protease by itself improved nutrient utilization and increased solubilization of NSP components, at the lower dose, a combination of xylanase, amylase, and protease produced effects greater than those of protease alone. PMID:26371327

Benchmark of Atucha-2 PHWR RELAP5-3D control rod model by Monte Carlo MCNP5 core calculation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pecchia, M.; D'Auria, F.; Mazzantini, O.

2012-07-01

Atucha-2 is a Siemens-designed PHWR reactor under construction in the Republic of Argentina. Its geometrical complexity and peculiarities require the adoption of advanced Monte Carlo codes for performing realistic neutronic simulations. Therefore core models of Atucha-2 PHWR were developed using MCNP5. In this work a methodology was set up to collect the flux in the hexagonal mesh by which the Atucha-2 core is represented. The scope of this activity is to evaluate the effect of obliquely inserted control rod on neutron flux in order to validate the RELAP5-3D{sup C}/NESTLE three dimensional neutron kinetic coupled thermal-hydraulic model, applied by GRNSPG/UNIPI formore » performing selected transients of Chapter 15 FSAR of Atucha-2. (authors)« less

Investigation of the Fluctuation Mechanism in Turbulent Flow

DTIC Science & Technology

1979-11-01

ft/sec, X /D - 31, 3>th arrays (i.e., Figs. I and 2) - U = 73 ft/sec, X !D - 15.5, Fig. I array only - U = 75 ft/set, X /D = 20.5, Fig. 2 array only - U...32.6 it/sec, X /D - 20.5, Both arrays The aim of these tests Is to yield data over A wide range of Reynolds numbers (i.e., from approximately 5000 to...34 -makes with the X -axis. Taking the average time delay between the measurements at C and F one obtains a stream- wise convection velocity of Uc/L,, = 0.70

Autism: Will vitamin D supplementation during pregnancy and early childhood reduce the recurrence rate of autism in newborn siblings?

PubMed

Stubbs, G; Henley, K; Green, J

2016-03-01

Vitamin D deficiency is widespread in the world including the vulnerable group of pregnant women. Vitamin D deficiency during pregnancy is hypothesized to contribute to the cause of autism. Further, it is hypothesized that vitamin D supplementation during pregnancy and early childhood will reduce the recurrence rate of autism in newborn siblings. To investigate the hypothesis an open label prospective study was performed prescribing vitamin D during pregnancy to mothers of children with autism at a dose of 5000IU/day. The newborn siblings were at high risk for the recurrence of autism. The newborn infants were also prescribed vitamin D, 1000IU/day to their third birthday. The newborn siblings were followed for three years and during that time, were assessed for autism on two separate occasions: at 18months and 36months of age. The results were compared to the reported recurrence rates in siblings of autistic children in the literature. The final outcome was 1 out of 19 (5%) developed autism in contrast to the recurrence rate of approximately 20% in the literature. We did not have a control group, nor was there blinding. The results are promising, however, this is a preliminary study with very small numbers and was uncontrolled. Further study with larger numbers is indicated. The ethics of prescribing a low dosage of vitamin D such as 400IU D3/day to a control group of mothers in comparison to a large dose such as 5000IU D3/day are problematic in our opinion. Copyright © 2016 The Authors. Published by Elsevier Ltd.. All rights reserved.

The Application of SERS (Surface Enhanced Raman Scattering) to Study Surface Oxidation Reactions of Phosphonates.

DTIC Science & Technology

1988-02-15

Center Attn: Dr. Ron Atkins Code 50C Chemistry Division Crane, Indiana 47522-5050 China Lake, California 93555 Scientific Advisor INaval Civil...Superintendent Marine Sciences Division Chemistry Division, Code 6100 San Diego, California 91232 Naval Research Laboratory Washington, D.C. 20375-5000 ,! .1

Implementation of SEREP Into LLNL Dyna3d for Global/Local Analysis

DTIC Science & Technology

2005-08-01

System Equivalent Reduction Expansion Process (SEREP). Presented at the 7th International Modal Analysis Conference, Las Vegas, NV, February 1989. 7...HUTCHINSON F SCHWARZ WARREN MI 48397-5000 14 BENET LABS AMSTA AR CCB R FISCELLA M SOJA E KATHE M SCAVULO G SPENCER P WHEELER

Temperature Compensation Techniques and Technologies-An Overview

DTIC Science & Technology

1991-10-01

03801-5423 General Electric Company 1 Physics International Company Tactical Systems Department ATTN: Library, H. Wayne Wampler ATN: J. Mandzy 2700...Keilasanath Office Dr. C. Li ATN: COL D. S. Jackson Dr. J. Boris 5321 Riggs Road Dr. E. Oran Gaithersburg, MD 20882 Washington, DC 20375-5000 AFOSR/NA 1 Amtec

Technical Note: Development and validation of an open data format for CT projection data.

PubMed

Chen, Baiyu; Duan, Xinhui; Yu, Zhicong; Leng, Shuai; Yu, Lifeng; McCollough, Cynthia

2015-12-01

Lack of access to projection data from patient CT scans is a major limitation for development and validation of new reconstruction algorithms. To meet this critical need, this work developed and validated a vendor-neutral format for CT projection data, which will further be employed to build a library of patient projection data for public access. A digital imaging and communication in medicine (DICOM)-like format was created for CT projection data (CT-PD), named the DICOM-CT-PD format. The format stores attenuation information in the DICOM image data block and stores parameters necessary for reconstruction in the DICOM header under various tags (51 tags to store the geometry and scan parameters and 9 tags to store patient information). To validate the accuracy and completeness of the new format, CT projection data from helical scans of the ACR CT accreditation phantom were acquired from two clinical CT scanners (Somatom Definition Flash, Siemens Healthcare, Forchheim, Germany and Discovery CT750 HD, GE Healthcare, Waukesha, WI). After decoding (by the authors for Siemens, by the manufacturer for GE), the projection data were converted to the DICOM-CT-PD format. Off-line CT reconstructions were performed by internal and external reconstruction researchers using only the information stored in the DICOM-CT-PD files and the DICOM-CT-PD field definitions. Compared with the commercially reconstructed CT images, the off-line reconstructed images created using the DICOM-CT-PD format are similar in terms of CT numbers (differences of 5 HU for the bone insert and -9 HU for the air insert), image noise (±1 HU), and low contrast detectability (6 mm rods visible in both). Because of different reconstruction approaches, slightly different in-plane and cross-plane high contrast spatial resolution were obtained compared to those reconstructed on the scanners (axial plane: GE off-line, 7 lp/cm; GE commercial, 7 lp/cm; Siemens off-line, 8 lp/cm; Siemens commercial, 7 lp/cm. Coronal plane: Siemens off-line, 6 lp/cm; Siemens commercial, 8 lp/cm). A vendor-neutral extended DICOM format has been developed that enables open sharing of CT projection data from third-generation CT scanners. Validation of the format showed that the geometric parameters and attenuation information in the DICOM-CT-PD file were correctly stored, could be retrieved with use of the provided instructions, and contained sufficient data for reconstruction of CT images that approximated those from the commercial scanner.

Folic acid supplements during pregnancy and child psychomotor development after the first year of life.

PubMed

Valera-Gran, Desirée; García de la Hera, Manuela; Navarrete-Muñoz, Eva María; Fernandez-Somoano, Ana; Tardón, Adonina; Julvez, Jordi; Forns, Joan; Lertxundi, Nerea; Ibarluzea, Jesús María; Murcia, Mario; Rebagliato, Marisa; Vioque, Jesús

2014-11-01

Folate intake during pregnancy has been associated with improved neuropsychological development in children, although the effects of high dosages of folic acid (FA) supplements are unclear. To examine the association between the use of high dosages of FA supplements during pregnancy and child neuropsychological development after the first year of life. The multicenter prospective mother-child cohort Infancia y Medio Ambiente (INMA) Project recruited pregnant women from 4 areas of Spain (Asturias, Sabadell, Gipuzkoa, and Valencia) between November 2003 and January 2008. Pregnant women completed an interviewer-administered questionnaire on the usual dietary folate intake and FA supplements at 10 to 13 weeks and 28 to 32 weeks of gestation. The main analyses were based on a sample of 2213 children with complete information on neuropsychological development and FA supplement intake during pregnancy. Multiple linear and logistic regression analyses were used to explore the effects of FA supplements on child neuropsychological development. Neuropsychological development was assessed using the Bayley Scales of Infant Development. We calculated mental scale and psychomotor scale scores. One SD below the mean established a delay in neurodevelopment (score <85). A high proportion of women (57.3%) did not reach the recommended dosages of FA supplements (400 μg/d), but 25.2% women took more than 1000 μg/d of FA supplements (3.5% consuming >5000 μg/d). In multivariate analysis, we observed that children whose mothers used FA supplement dosages higher than 5000 μg/d during pregnancy had a statistically significantly lower mean psychomotor scale score (difference, -4.35 points; 95% CI, -8.34 to -0.36) than children whose mothers used a recommended dosage of FA supplements (400-1000 μg/d). An increased risk of delayed psychomotor development (psychomotor scale score <85) was also evident among children whose mothers took FA supplement dosages higher than 5000 μg/d, although the association was not statistically significant (odds ratio = 1.59; 95% CI, 0.82-3.08). To our knowledge, this is the first time a detrimental effect of high dosages of FA supplements during pregnancy on psychomotor development after the first year of life has been shown. Further research from longitudinal studies is warranted to confirm these results.

New software to model energy dispersive X-ray diffraction in polycrystalline materials

NASA Astrophysics Data System (ADS)

Ghammraoui, B.; Tabary, J.; Pouget, S.; Paulus, C.; Moulin, V.; Verger, L.; Duvauchelle, Ph.

2012-02-01

Detection of illicit materials, such as explosives or drugs, within mixed samples is a major issue, both for general security and as part of forensic analyses. In this paper, we describe a new code simulating energy dispersive X-ray diffraction patterns in polycrystalline materials. This program, SinFullscat, models diffraction of any object in any diffractometer system taking all physical phenomena, including amorphous background, into account. Many system parameters can be tuned: geometry, collimators (slit and cylindrical), sample properties, X-ray source and detector energy resolution. Good agreement between simulations and experimental data was obtained. Simulations using explosive materials indicated that parameters such as the diffraction angle or the energy resolution of the detector have a significant impact on the diffraction signature of the material inspected. This software will be a convenient tool to test many diffractometer configurations, providing information on the one that best restores the spectral diffraction signature of the materials of interest.

X-Ray diffraction on large single crystals using a powder diffractometer

DOE PAGES

Jesche, A.; Fix, M.; Kreyssig, A.; ...

2016-06-16

Information on the lattice parameter of single crystals with known crystallographic structure allows for estimations of sample quality and composition. In many cases it is sufficient to determine one lattice parameter or the lattice spacing along a certain, high- symmetry direction, e.g. in order to determine the composition in a substitution series by taking advantage of Vegard’s rule. Here we present a guide to accurate measurements of single crystals with dimensions ranging from 200 μm up to several millimeter using a standard powder diffractometer in Bragg-Brentano geometry. The correction of the error introduced by the sample height and the optimizationmore » of the alignment are discussed in detail. Finally, in particular for single crystals with a plate-like habit, the described procedure allows for measurement of the lattice spacings normal to the plates with high accuracy on a timescale of minutes.« less

Advanced setup for high-pressure and low-temperature neutron diffraction at hydrostatic conditions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lokshin, Konstantin A.; Zhao Yusheng

2005-06-15

We describe a design of the experimental setup for neutron diffraction studies at low temperatures and hydrostatic pressure. The significant benefit of the setup, compared to the previous methods, is that it makes possible the simultaneous collection of neutrons diffracted at the 30 deg. -150 deg. range with no contamination by the primary scattering from the sample surroundings and without cutting out the incident and diffracted beams. The suggested design is most useful for third-generation time-of-flight diffractometers and constant wavelength instruments. Application of the setup expands the capabilities of high-pressure neutron diffraction, allowing time-resolved kinetics and structural studies, multihistogram Rietveld,more » and pair distribution function and texture analyses. The high efficiency of the setup was proven for the HIPPO diffractometer at Los Alamos Neutron Science Center under pressures up to 10 kbar and temperatures from 4 to 300 K.« less

On high-resolution reciprocal-space mapping with a triple-crystal diffractometer for high-energy X-rays.

PubMed

Liss, K D; Royer, A; Tschentscher, T; Suortti, P; Williams, A P

1998-03-01

High-energy X-rav diffraction by means of triple-crystal techniques is a powerful tool for investigating dislocations and strain in bulk materials. Radiation with an energy typically higher than 80 keV combines the advantage of low attenuation with high resolution at large momentum transfers. The triple-crystal diffractometer at the High Energy Beamline of the European Synchrotron Radiation Facility is described. It is shown how the transverse and longitudinal resolution depend on the choice of the crystal reflection, and how the orientation of a reciprocal-lattice distortion in an investigated sample towards the resolution element of the instrument can play an important role. This effect is demonstrated on a single crystal of silicon where a layer of macro pores reveals satellites around the Bragg reflection. The resulting longitudinal distortion can be investigated using the high transverse resolution of the instrument when choosing an appropriate reflection.

SMA texture and reorientation: simulations and neutron diffraction studies

NASA Astrophysics Data System (ADS)

Gao, Xiujie; Brown, Donald W.; Brinson, L. Catherine

2005-05-01

With increased usage of shape memory alloys (SMA) for applications in various fields, it is important to understand how the material behavior is affected by factors such as texture, stress state and loading history, especially for complex multiaxial loading states. Using the in-situ neutron diffraction loading facility (SMARTS diffractometer) and ex situ inverse pole figure measurement facility (HIPPO diffractometer) at the Los Alamos Neutron Science Center (LANCE), the macroscopic mechanical behavior and texture evolution of Nickel-Titanium (Nitinol) SMAs under sequential compression in alternating directions were studied. The simplified multivariant model developed at Northwestern University was then used to simulate the macroscopic behavior and the microstructural change of Nitinol under this sequential loading. Pole figures were obtained via post-processing of the multivariant results for volume fraction evolution and compared quantitatively well to the experimental results. The experimental results can also be used to test or verify other SMA constitutive models.

Composite germanium monochromators - Results for the TriCS single-crystal diffractometer at SINQ

NASA Astrophysics Data System (ADS)

Schefer, J.; Fischer, S.; Böhm, M.; Keller, L.; Horisberger, M.; Medarde, M.; Fischer, P.

Composite germanium monochromators are foremost in application in neutron diffraction due to their good scattering properties, low absorption values and the diamond structure which avoids second-order contamination when using hhk reflections (all odd). Our slices for the monochromator are built from 24 wafers, each 0.4 mm thick. The alignment of the wafers within the final composite wafer package has been improved by adding tin for the soldering process with a sputtering method instead of foils. Nine slices, each 12.5 mm high, are mounted on separate miniature goniometer heads to the focusing monochromator. The focusing angle is controlled by only one motor/digitizer by using a sophisticated mechanism. Turning the monochromator by 9° around overlineω allow access of the 311 (primary) and 511 (secondary) reflection. We also show the importance of permanent quality control with neutrons. The monochromator will be used on the single-crystal diffractometer TriCS at SINQ.

Role of Bi3+ substitution on structural, magnetic and optical properties of cobalt spinel ferrite

NASA Astrophysics Data System (ADS)

Anjum, Safia; Sehar, Fatima; Awan, M. S.; Zia, Rehana

2016-04-01

Bismuth-doped cobalt ferrite CoBi x Fe(2- x)O4 with x = 0, 0.1,0.2, 0.3, 0.4, 0.5 have been prepared using powder metallurgy route. The structural, morphological, elemental, magnetic and optical properties have been investigated using X-ray diffractometer, Fourier transform infrared spectroscopy, scanning electron microscope, energy dispersive X-rays, vibrating sample magnetometer and ultraviolet-visible spectrometer, respectively. X-ray diffractometer analysis confirms the formation of single-phase cubic spinel structure. As the substitution of larger ionic radii Bi3+ ions increases in cobalt ferrite which is responsible to increase the lattice parameters and decrease the crystallite size. SEM micrographs revealed the spherical shape of the particles with the nonuniform grain boundaries. The saturation magnetization decreases and bandgap energy increases as the concentration of non-magnetic Bi3+ ions increases.

NIMROD: The Near and InterMediate Range Order Diffractometer of the ISIS second target station.

PubMed

Bowron, D T; Soper, A K; Jones, K; Ansell, S; Birch, S; Norris, J; Perrott, L; Riedel, D; Rhodes, N J; Wakefield, S R; Botti, A; Ricci, M-A; Grazzi, F; Zoppi, M

2010-03-01

NIMROD is the Near and InterMediate Range Order Diffractometer of the ISIS second target station. Its design is optimized for structural studies of disordered materials and liquids on a continuous length scale that extends from the atomic, upward of 30 nm, while maintaining subatomic distance resolution. This capability is achieved by matching a low and wider angle array of high efficiency neutron scintillation detectors to the broad band-pass radiation delivered by a hybrid liquid water and liquid hydrogen neutron moderator assembly. The capabilities of the instrument bridge the gap between conventional small angle neutron scattering and wide angle diffraction through the use of a common calibration procedure for the entire length scale. This allows the instrument to obtain information on nanoscale systems and processes that are quantitatively linked to the local atomic and molecular order of the materials under investigation.

Environmental testing of CIS based modules

DOE Office of Scientific and Technical Information (OSTI.GOV)

Willett, D.

1995-11-01

This report describes environmental testing of Siemen`s CIS modules. Charts and diagrams are presented on data concerning: temporary power loss of laminated mini-modules; the 50 thermal cycle test; the 10 humidity freeze cycle test; results after 1000 hours of exposure to damp heat; and interconnect test structures in damp heat testing. It is concluded that moisture ingress causes permanent increases in the series resistance of modules, and that improved packaging is needed for better high humidity reliability. Also, dry dark heat caused temporary power losses which were recovered in sunlight.

Thermal Shock Properties of a 2D-C/SiC Composite Prepared by Chemical Vapor Infiltration

NASA Astrophysics Data System (ADS)

Zhang, Chengyu; Wang, Xuanwei; Wang, Bo; Liu, Yongsheng; Han, Dong; Qiao, Shengru; Guo, Yong

2013-06-01

The thermal shock properties of a two-dimensional carbon fiber-reinforced silicon carbide composite with a multilayered self-healing coating (2D-C/SiC) were investigated in air. The composite was prepared by low-pressure chemical vapor infiltration. 2D-C/SiC specimens were thermally shocked for different cycles between 900 and 300 °C. The thermal shock resistance was characterized by residual tensile properties and mass variation. The change of the surface morphology and microstructural evolution of the composite were examined by a scanning electron microscope. In addition, the phase evolution on the surfaces was identified using an X-ray diffractometer. It is found that the composite retains its tensile strength within 20 thermal shock cycles. However, the modulus of 2D-C/SiC decreases gradually with increasing thermal shock cycles. Extensive pullout of fibers on the fractured surface and peeling off of the coating suggest that the damage caused by the thermal shock involves weakening of the bonding strength of coating/composite and fiber/matrix. In addition, the carbon fibers in the near-surface zone were oxidized through the matrix cracks, and the fiber/matrix interfaces delaminated when the composite was subjected to a larger number of thermal shock cycles.

Alternative Fuels Data Center: ASTM Biodiesel Specifications

Science.gov Websites

purchased from ASTM International. Property Test Method Grade No.1-B S15 Grade No.1-B S500 Grade No.2-B S15 ASTM International. Property Test Method Grade B6 to B20 S15 B6 to B20 S500 j B6 to B20 S5000 Acid for the intended use and expected ambient temperatures. Test Methods D 4539 and D 6371 may be useful

Mission Planning System Increment 5 (MPS Inc 5)

DTIC Science & Technology

2016-03-01

DoD - Department of Defense DoDAF - DoD Architecture Framework FD - Full Deployment FDD - Full Deployment Decision FY - Fiscal Year IA...Alternative Selected (Funds First Obligated (FFO)) (O/T) : Mar 2013 / Mar 2013 • MS B (O/T) : Apr 2012 / Apr 2012 • MS C (O/T) : N/A / N/A • FDD (O/T...Deployed Software Intensive Program" as described in the DOD Instruction 5000.02, January 7, 2015. 4. FDD provides approval to field the

F-35 Lightning II Program Quality Assurance and Corrective Action Evaluation

DTIC Science & Technology

2015-03-11

5000.02, “Operation of the Defense Acquisition System,” enclosure 1; and DoD Manual 4140.01, “DoD Supply Chain Materiel Management Procedures...initiated several initiatives to reduce nonconformances of all types both within their facilities and throughout their supply chains . The F-35 JPO is...agreed and stated: There are effective Corrective Action processes already in place within Lockheed Martin and the supply chain . DCMA and F-35 JPO

A Neanderthal lower molar from Stajnia Cave, Poland.

PubMed

Dąbrowski, P; Nowaczewska, W; Stringer, C B; Compton, T; Kruszyński, R; Nadachowski, A; Stefaniak, K; Urbanowski, M

2013-04-01

The primary aim of this study was to conduct a taxonomic assessment of the second of three isolated human teeth found in the Stajnia Cave (north of the Carpathians, Poland) in 2008. The specimen was located near a human tooth (S5000), which was identified by Urbanowski et al. (2010) as a Neanderthal permanent upper molar. Both of these teeth were excavated from the D2 layer, which belongs to the D stratigraphic complex comprising the archaeological assemblage associated with the Micoquian tradition. An Ursus spelaeus bone and Mammuthus primigenius tooth that were also excavated from the D2 layer were dated to >49,000 years BP (by AMS (14)C) and 52.9 ka BP (by U-Th), respectively. The sediment overlying stratigraphic complex D was dated to 45.9 ka BP by the OSL method. The S4300 tooth is a lower first or second permanent molar belonging to an individual other than that who once possessed the S5000 tooth. The S4300 tooth exhibits a combination of traits typical of Neanderthal lower molars, including a mid-trigonid crest, large anterior fovea, taurodontism and subvertical grooves on the interproximal face, indicating that this tooth belonged to a Neanderthal individual. The S4300 tooth from Stajnia Cave is one of the oldest human remains found in Poland. Copyright © 2013 Elsevier GmbH. All rights reserved.

Additional of polyethylene glycol on the preparation of LaPO4:Eu3+ phosphor

NASA Astrophysics Data System (ADS)

Panatarani, Camellia; Joni, I. Made

2013-09-01

Solution phase method was used to synthesis nanocrystal LaPO4:Eu3+. Polyethylene glycol with vary molecular weight (MW) was added to allow an exothermic reaction to get a high crystalinity of LaPO4:Eu3+. The x-ray pattern of as prepared LaPO4 was obtained by using an X'pert PANalytical diffractometer with CuKα radiation (λ = 1.5406 Å) and the photoluminescent measurement spectra is obtained by using Fluorescence Spectrometer LS55, Perkin Elmer. The additional of various MW of polyethylene glycol into the precursor solution of LaPO4:Eu3+ affected the crystal structure and luminescent properties. Higher MW of PEG depressing the luminescent spectra. The emission origin from 5D0-7F4 transition vanished by additional 500,000 and 2,000,000 MW of PEG.

Residual stress determination in an overlay dissimilar welded pipe by neutron diffraction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Woo, Wan Chuck; Em, Vyacheslav; Hubbard, Camden R

2011-01-01

Residual stresses were determined through the thickness of a dissimilar weld overlay pipe using neutron diffraction. The specimen has a complex joining structure consisting of a ferritic steel (SA508), austenitic steel (F316L), Ni-based consumable (Alloy 182), and overlay of Ni-base superalloy (Alloy 52M). It simulates pressurized nozzle components, which have been a critical issue under the severe crack condition of nuclear power reactors. Two neutron diffractometers with different spatial resolutions have been utilized on the identical specimen for comparison. The macroscopic 'stress-free' lattice spacing (d{sub o}) was also obtained from both using a 2-mm width comb-like coupon. The results showmore » significant changes in residual stresses from tension (300-400 MPa) to compression (-600 MPa) through the thickness of the dissimilar weld overlay pipe specimen.« less

Evaluation of clinical image processing algorithms used in digital mammography.

PubMed

Zanca, Federica; Jacobs, Jurgen; Van Ongeval, Chantal; Claus, Filip; Celis, Valerie; Geniets, Catherine; Provost, Veerle; Pauwels, Herman; Marchal, Guy; Bosmans, Hilde

2009-03-01

Screening is the only proven approach to reduce the mortality of breast cancer, but significant numbers of breast cancers remain undetected even when all quality assurance guidelines are implemented. With the increasing adoption of digital mammography systems, image processing may be a key factor in the imaging chain. Although to our knowledge statistically significant effects of manufacturer-recommended image processings have not been previously demonstrated, the subjective experience of our radiologists, that the apparent image quality can vary considerably between different algorithms, motivated this study. This article addresses the impact of five such algorithms on the detection of clusters of microcalcifications. A database of unprocessed (raw) images of 200 normal digital mammograms, acquired with the Siemens Novation DR, was collected retrospectively. Realistic simulated microcalcification clusters were inserted in half of the unprocessed images. All unprocessed images were subsequently processed with five manufacturer-recommended image processing algorithms (Agfa Musica 1, IMS Raffaello Mammo 1.2, Sectra Mamea AB Sigmoid, Siemens OPVIEW v2, and Siemens OPVIEW v1). Four breast imaging radiologists were asked to locate and score the clusters in each image on a five point rating scale. The free-response data were analyzed by the jackknife free-response receiver operating characteristic (JAFROC) method and, for comparison, also with the receiver operating characteristic (ROC) method. JAFROC analysis revealed highly significant differences between the image processings (F = 8.51, p < 0.0001), suggesting that image processing strongly impacts the detectability of clusters. Siemens OPVIEW2 and Siemens OPVIEW1 yielded the highest and lowest performances, respectively. ROC analysis of the data also revealed significant differences between the processing but at lower significance (F = 3.47, p = 0.0305) than JAFROC. Both statistical analysis methods revealed that the same six pairs of modalities were significantly different, but the JAFROC confidence intervals were about 32% smaller than ROC confidence intervals. This study shows that image processing has a significant impact on the detection of microcalcifications in digital mammograms. Objective measurements, such as described here, should be used by the manufacturers to select the optimal image processing algorithm.

49 CFR Appendix G to Part 227 - Schedule of Civil Penalties

Code of Federal Regulations, 2010 CFR

2010-10-01

... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION OCCUPATIONAL NOISE EXPOSURE Pt. 227, App. G Appendix G to Part 227... Requirements 227.103Noise monitoring program: (a) Failure to develop and/or implement a noise monitoring... levels and/or make noise measurements as required 2,500 5,000 (d) Failure to repeat noise monitoring...

78 FR 7348 - Patient Protection and Affordable Care Act; Exchange Functions: Eligibility for Exemptions...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-02-01

... se and those that may apply for recognition are neither group health insurance coverage nor.... 156.602) c. Requirements for Recognition as Minimum Essential Coverage for Coverage Not Otherwise... recognition that they meet the standards under section 5000A(d)(2)(B) of the Code. We also received...

32 CFR 32.34 - Equipment.

Code of Federal Regulations, 2010 CFR

2010-07-01

... current fair market value where a recipient compensates the DoD Component that made the award for its... following standards. (1) For equipment with a current per unit fair market value of $5,000 or more, the... current fair market value of the equipment. (2) If the recipient has no need for the equipment, the...

Group 31 and Group 34 Li-ion Battery Specification

DTIC Science & Technology

2011-02-08

AUTHOR(S) 5d. PROJECT NUMBER 5e. TASK NUMBER 5f. WORK UNIT NUMBER 7. PERFORMING ORGANIZATION NAME(S) AND ADDRESS(ES) US Army RDECOM-TARDEC 6501 E...11 Mile Rd Warren, MI 48397-5000, USA 8. PERFORMING ORGANIZATION REPORT NUMBER 21530 9. SPONSORING/MONITORING AGENCY NAME(S) AND ADDRESS(ES) US

Comparison between a Terramechanics Model and a Continuum Soil Model Implemented within the Absolute Nodal Coordinate Formulation

DTIC Science & Technology

2012-08-01

Chicago, IL 60607, USA Email: fosterc@uic.edu Paramsothy Jayakumar U.S. Army RDECOM-TARDEC Warren, MI 48397-5000, USA...Mike Letherwood; Paramsothy Jayakumar ; Guangbu Li; Ulysses Contreras; Craig Foster 5d. PROJECT NUMBER 5e. TASK NUMBER 5f. WORK UNIT NUMBER 7

50 CFR 665.269 - Quotas.

Code of Federal Regulations, 2011 CFR

2011-10-01

... which it is based as soon as practicable after the determination is made. (d) Quotas for precious coral... Beds Au'au Channel Black: 5,000 2 Makapu'u Pink: 2,000 2 Gold: 0 (zero) Bamboo: 500 2 Conditional Beds... Westpac All: 0 (zero) Exploratory Area Hawaii 1,000 per area (all species combined except black corals) 1...

50 CFR 665.269 - Quotas.

Code of Federal Regulations, 2010 CFR

2010-10-01

... which it is based as soon as practicable after the determination is made. (d) Quotas for precious coral... Beds Au'au Channel Black: 5,000 2 Makapu'u Pink: 2,000 2 Gold: 0 (zero) Bamboo: 500 2 Conditional Beds... Westpac All: 0 (zero) Exploratory Area Hawaii 1,000 per area (all species combined except black corals) 1...

Factors limiting the sensitivity and dynamic range of a seismic system employing analog magnetic tape recording and a seismic amplifier with adjustable gain settings and several output levels

USGS Publications Warehouse

Eaton, Jerry P.; Van Schaack, John R.

1977-01-01

In the course of modernizing the low-speed-tape-recorder portable seismic systems and considering the possibilities for the design of a cassette-tape-recorder seismic refraction system, the factors that limit the sensitivity and dynamic range of such systems have been reviewed. These factors will first be stated briefly, and then their influence on systems such as the new 5-day-tape seismic system will be examined in more detail. To fix ideas, we shall assume that the system consists of the following elements: 1. A seismic sensor: usually a moving coil inertial seismometer with a period of about 1 second, a coil resistance of about 5000 ohms, and an effective motor constant of 1.0 V/cm/sec (across a 10K load terminating the seismometer sensitivity-and-damping-adjustment resistive network). 2. A seismic amplifier/voltage controlled oscillator unit made up of the following components: a) A fixed gain preamplifier with an input resistance of 10K and an internal noise level of 0.5 muVpp referred to the preamp input (0.1 Hz <= freq. <= 30 hz). b) An adjustable gain (0 to 42 db in 6 db steps) intermediate amplifier c) One or more fixed gain output amplifiers. d) Two sections of 6 db/octave bandpass filter serving to couple the 3 amplifier stages together. e) Voltage controlled oscillators for each output amplifier to produce modulated FM carriers for recording on separate tape tracks or modulated FM subcarriers for subsequent multiplexing and direct recording on tape in the California Network format. 3. An analog magnetic tape recorder: e.g. the PI 5100 (15/80 ips recording in the FM mode or in the direct mode with the 'broad-band' variant-of the Cal Net multiplex system, or 15/16 ips recording in the direct mode with the standard Cal Net multiplex system), or the Sony TC-126 cassette recorder operating in the direct record mode with the standard Cal Net multiplex system. 4. Appropriate magnetic tape playback equipment: e.g., the Bell and Howell 3700-B for the PI-5100 or the Sony TC 126 for its own tapes. 5. Appropriate discriminators (employing subtractive compensation, at least for the multiplexed systems) to restore the data signals to their original forms. 6. An A/D convertor to digitize the seismic signals for computer processing and/or a strip chart recorder (e.g., the Siemens Oscillomink) for playout of the data.

The climatic effects of nuclear war

NASA Technical Reports Server (NTRS)

Turco, R. P.; Toon, O. B.; Ackerman, T. P.; Pollack, J. B.; Sagan, C.

1984-01-01

The effects of various US-USSR nuclear-exchange scenarios on global climate are investigated by means of computer simulations, summarizing the results of Turco et al. (1983) and follow-up studies using 3D global-circulation models. A nuclear-scenario model is used to determine the amounts of dust, smoke, radioactivity, and pyrotoxins generated by a particular type of nuclear exchange (such as a general 5,000-Mt exchange, a 1,000-Mt limited exchange, a 5,000-Mt hard-target counterforce attack, and a 100-Mt attack on cities only): a particle-microphysics model predicts the evolution of the dust and smoke particles; and a radiative-convective climate model estimates the effects of the dust and smoke clouds on the global radiation budget. The findings are presented in graphs, diagrams, and a table. Thick clouds blocking most sunlight over the Northern Hemisphere midlatitudes for weeks or months and producing ground-temperature reductions of 20-40 C, disruption of global circulation patterns, and rapid spread of clouds to the Southern Hemisphere are among the 'nuclear-winter' effects predicted for the 5,000-Mt baseline case. The catastrophic consequences for plant, animal, and human populations are considered, and the revision of superpower nuclear strategies is urged.

Total cross sections of electron scattering by molecules NF3, PF3, N(CH3)3, P(CH3)3, NH(CH3)2, PH(CH3)2, NH2CH3 and PH2CH3 at 30-5000 eV

NASA Astrophysics Data System (ADS)

Shi, D. H.; Sun, J. F.; Zhu, Z. L.; Liu, Y. F.

2010-04-01

Total cross sections of electron scattering by eight molecules NF3, PF3, N(CH3)3, P(CH3)3, NH(CH3)2, PH(CH3)2, NH2CH3 and PH2CH3, which have some structural similarities, are calculated at the Hartree-Fork level by the modified additivity rule approach [D.H. Shi, J.F. Sun, Z.L. Zhu, H. Ma, Y.F. Liu, Eur. Phys. J. D 45, 253 (2007); D.H. Shi, J.F. Sun, Y.F. Liu, Z.L. Zhu, X.D. Yang, Chin. Opt. Lett. 4, 192 (2006)]. The modified additivity rule approach takes into considerations that the contributions of the geometric shielding effect vary as the energy of incident electrons, the dimension of target molecule, the number of electrons in the molecule and the number of atoms constituting the molecule. The present investigations cover the impact energy range from 30 to 5000 eV. The quantitative total cross sections are compared with those obtained by experiments and other theories. Excellent agreement is observed even at energies of several tens of eV. It shows that the modified additivity rule approach is applicable to carry out the total cross section calculations of electron scattering by these molecules at intermediate and high energies, in particular over the energy range above 80 eV or so. It proves that the microscopic molecular properties, such as the geometrical size of the target and the number of atoms constituting the molecule, are of crucial importance in the TCS calculations. The new results for PH(CH3)2 and PH2CH3 are also presented at energies from 30 to 5000 eV, although no experimental and theoretical data are available for comparison. In the present calculations, the atoms are still represented by the spherical complex optical potential, which is composed of static, exchange, polarization and absorption terms.

Understanding and Modeling Vortical Flows to Improve the Technology Readiness Level for Military Aircraft (Comprehension et Modelisation des Flux de Vortex Pour Ameliorer le Niveau de Maturite Technologique au Profit des Avions Militaires)

DTIC Science & Technology

2009-10-01

636.7 115,418 0 2500 5000 7500 10000 12500 iterations -5 -4 -3 -2 -1 0 lo g( dρ /d t) SA EARSM EARSM + CC Hellsten EARSM Hellsten EARSM + CC DRSM...VORTEX BREAKDOWN RTO-TR-AVT-113 29 - 13 θU URo axial= (1) As a vortex passes through a normal shock, the tangential velocity is

DoD Student Meal Program

DTIC Science & Technology

1983-10-11

Section 1408, "Defense Dependents’ Education Act of 1978," November 1, 1978 (42 U.S.C. 1769b, 1773, and 1789) "W b Title 42, United States Code, Section...83 1015.5 p. Ensures that student meal programs are conducted in a manner that minimizes interference with educational programs. q. Employs a food...34Eligibility Requirements for Education of Minor Dependents in Overseas Areas," July 8, 1982 (g) DoD Directive 5000.19, "Policies for the Management and

Documentation for the USAF School of Aerospace Medicine Altitude Decompression Sickness Research Database

DTIC Science & Technology

2010-05-01

following investigators have been listed on protocols where DCS and/or VGE were the primary data gathered (omits PRK and LASIK ): Jimmy D. Adams, PhD...there was a difference in the level of upper vs . lower-body joint pain which was evident statistically when many non-ambulatory vs . ambulatory studies...5,000 fpm vs . 80,000 fpm ascents to 40,000 ft (90-min prebreathe, 90-min exposure), there were a few more neurologic and respiratory symptoms

Total Quality Management Guide. A Two Volume Guide for Defense Organizations. Volume 1. Key Features of the DoD Implementation

DTIC Science & Technology

1990-02-15

XIALTM DoD 5000.51-G A * FINAL DRAFT 2/15/90 si- N ~LUM I -KY FEATRES OFTHE Do IMLEENAON TOTAL L/ De~rrn QUADefens FOREWORD Government and industry...away with all government inspectors. Rather. government oversight will change from te large scale product inspection and specifying the -how to...in class" - Set the course for the future, and - Provide a baseline for measuring progress. Benchmarking is a continuous process of comparing an

NHEXAS PHASE I ARIZONA STUDY--STANDARD OPERATING PROCEDURE FOR OPERATION, CALIBRATION AND MAINTENANCE OF THE PERKIN-ELMER ZEEMAN/5000 SYSTEM ATOMIC ABSORPTION SPECTROMETER (BCO-L-6.0)

EPA Science Inventory

The purpose of this SOP is to outline the start-up, calibration, operation, and maintenance procedures for the Perkin-Elmer 5000 atomic absorption spectrophotometer (PE 5000 AA), and the Perkin Elmer 5000 Zeeman graphite furnace atomic absorption spectrophotometer (PE 5000Z GFAA)...

Application of NX Siemens PLM software in educational process in preparing students of engineering branch

NASA Astrophysics Data System (ADS)

Sadchikova, G. M.

2017-01-01

This article discusses the results of the introduction of computer-aided design NX by Siemens Plm Software to the classes of a higher education institution. The necessity of application of modern information technologies in teaching students of engineering profile and selection of a software product is substantiated. The author describes stages of the software module study in relation to some specific courses, considers the features of NX software, which require the creation of standard and unified product databases. The article also gives examples of research carried out by the students with the various software modules.

Development of Behavior-Based Scales and Analysis of Recruiter Selection Battery Data for the Army Recruiter Job

DTIC Science & Technology

1987-05-01

999. 78. For how many years did you belong to youth d: 41,000 to $4.999. girp-such as Boy/ Girl Scouts, Captire e. $5,000 or over. &irls, etc? a. I year...supervision, d. A person with other interests that seemed 79. When you nude a wrong choice regarding a to detract from attention to the family...outlined d. Feel I nude the best rhoice I could at what they wanted me to do. the tine. b. Were interested and helped ue outline e. Something else. what

Study of Sedimentary Outcrop of Semanggol Formation with the Correlation of Geology, Geotechnical and Geophysics Technique

NASA Astrophysics Data System (ADS)

Nordiana, A. N.; Nordiana, M. M.; Jia, Teoh Ying; Hisham, Hazrul; Sulaiman, Nabila; Maslinda, Umi; Taqiuddin, Z. M.; Nur Amalina, M. K. A.; Afiq Saharudin, Muhamad

2017-04-01

The study location was at Bukit Kukus, Kuala Ketil, Kedah, Malaysia where the geological outcrop of this Semanggol Formation comprises of chert, mudstone, and volcanic tuff. The study was conducted using two geophysical methods, which are 2-D Resistivity and Ground Penetrating Radar (GPR). The objectives of the study are to correlate both of the geophysical methods through the value of conductivity and to identify the physical properties of rocks through the value of porosity and permeability. The data acquisition for both methods was conducted on the same line. For 2-D Resistivity method, the length of the line is 60 m with 1.5 m electrode spacing and the array used was Wenner-Schlumberger. For GPR method, the survey line was on top of the resistivity line, and the frequency of the antenna used is 250 MHz. A good correlation exists between both of the GPR signature and contour maps for resistivity from the surfer 10 software with the outcrop feature. Conductivity value from both GPR and Resistivity method was compared and the range value of conductivity obtained from GPR method almost equivalent with Resistivity method based on derivation and calculation for the sedimentary rocks, which are 0.037 to 0.574 miliSiemens per metre (mS/m) for chert and 0.186 to 10.142 miliSiemens per metre (mS/m) for mudstone. Two types of rock samples were taken, and several geotechnical tests were conducted, but only the value of permeability, K and porosity, ɸ of chert can be calculated, which are 1.95E-22 m2 (original condition) and 2.27E-22 m2 (dry condition) and 3 percent respectively as the sample of mudstone was damaged. The parameter of the 2-D resistivity method derived from Archie’s law was used to calculate the porosity, ɸf value using the Formation Factor equation. The range values of porosity, ɸf for chert mostly in the range of 5 to 25 percent, which is 6.26 to 13.36 percent but slightly out of range for mudstone, which is 14.12 to 36.02 percent.

U.S.-MEXICO BORDER PROGRAM ARIZONA BORDER STUDY--STANDARD OPERATING PROCEDURE FOR OPERATION, CALIBRATION, AND MAINTENANCE OF THE PERKIN-ELMER ZEEMAN/5000 SYSTEM ATOMIC ABSORPTION SPECTROPHOTOMETER (BCO-L-6.0)

EPA Science Inventory

The purpose of this SOP is to outline the start-up, calibration, operation, and maintenance procedures for the Perkin-Elmer 5000 atomic absorption spectrophotometer (PE 5000 AA), and the Perkin Elmer 5000 Zeeman graphite furnace atomic absorption spectrophotometer (PE 5000Z GFAA)...

Acute Toxicity of a Number of Chemicals of Interest to the Air Force

DTIC Science & Technology

1979-03-01

Acid Azelaic Acid Dimer Acid N-Benzyl-3, 7-Dioctyl Phenothiazine Phenothiazine Dioctyl Phenothiazine Sebacic Acid ...liquid) 1,4-dihydroxyanthraquinone (solid) Sulfurized 9-octadecenoic acid (liquid) Azelaic acid (solid) Dimer acid (liquid) N-benzyl-3,7-dicotyl...dihydroxyanthra- Rat >5000 5000(0) Below Toxic quinone Sulfurized 9-octa- Rat >5000 5000(0) Below Toxic decenoic acid Azelaic acid Rat >5000

CFD Analysis of Thermal Control System Using NX Thermal and Flow

NASA Technical Reports Server (NTRS)

Fortier, C. R.; Harris, M. F. (Editor); McConnell, S. (Editor)

2014-01-01

The Thermal Control Subsystem (TCS) is a key part of the Advanced Plant Habitat (APH) for the International Space Station (ISS). The purpose of this subsystem is to provide thermal control, mainly cooling, to the other APH subsystems. One of these subsystems, the Environmental Control Subsystem (ECS), controls the temperature and humidity of the growth chamber (GC) air to optimize the growth of plants in the habitat. The TCS provides thermal control to the ECS with three cold plates, which use Thermoelectric Coolers (TECs) to heat or cool water as needed to control the air temperature in the ECS system. In order to optimize the TCS design, pressure drop and heat transfer analyses were needed. The analysis for this system was performed in Siemens NX Thermal/Flow software (Version 8.5). NX Thermal/Flow has the ability to perform 1D or 3D flow solutions. The 1D flow solver can be used to represent simple geometries, such as pipes and tubes. The 1D flow method also has the ability to simulate either fluid only or fluid and wall regions. The 3D flow solver is similar to other Computational Fluid Dynamic (CFD) software. TCS performance was analyzed using both the 1D and 3D solvers. Each method produced different results, which will be evaluated and discussed.

Actuator line simulations of a Joukowsky and Tjæreborg rotor using spectral element and finite volume methods

NASA Astrophysics Data System (ADS)

Kleusberg, E.; Sarmast, S.; Schlatter, P.; Ivanell, S.; Henningson, D. S.

2016-09-01

The wake structure behind a wind turbine, generated by the spectral element code Nek5000, is compared with that from the finite volume code EllipSys3D. The wind turbine blades are modeled using the actuator line method. We conduct the comparison on two different setups. One is based on an idealized rotor approximation with constant circulation imposed along the blades corresponding to Glauert's optimal operating condition, and the other is the Tjffireborg wind turbine. The focus lies on analyzing the differences in the wake structures entailed by the different codes and corresponding setups. The comparisons show good agreement for the defining parameters of the wake such as the wake expansion, helix pitch and circulation of the helical vortices. Differences can be related to the lower numerical dissipation in Nek5000 and to the domain differences at the rotor center. At comparable resolution Nek5000 yields more accurate results. It is observed that in the spectral element method the helical vortices, both at the tip and root of the actuator lines, retain their initial swirl velocity distribution for a longer distance in the near wake. This results in a lower vortex core growth and larger maximum vorticity along the wake. Additionally, it is observed that the break down process of the spiral tip vortices is significantly different between the two methods, with vortex merging occurring immediately after the onset of instability in the finite volume code, while Nek5000 simulations exhibit a 2-3 radii period of vortex pairing before merging.

Synthesis of Carbonate-Based Micro/Nanoscale Particles With Controlled Morphology and Mineralogy

DTIC Science & Technology

2013-04-01

patterns were obtained using a Panalytical X’Pert Pro diffractometer using iron-filtered cobalt radiation, and analyzed using Panalytical X’Pert...develop composites by hydrothermal recrystallization of metastable phases. 15. SUBJECT TERMS Aragonite Calcite Calcium carbonate Dopant Mineralogy

40 CFR 1051.105 - What are the exhaust emission standards for off-highway motorcycles?

Code of Federal Regulations, 2010 CFR

2010-07-01

... lights. (B) The absence of a spark arrestor. (C) The absence of manufacturer warranty. (D) Suspension... displacement greater than 70 cc, the minimum useful life is 10,000 kilometers or five years, whichever comes... minimum useful life is 5,000 kilometers or five years, whichever comes first. You must specify a longer...

40 CFR 1051.105 - What are the exhaust emission standards for off-highway motorcycles?

Code of Federal Regulations, 2011 CFR

2011-07-01

... lights. (B) The absence of a spark arrestor. (C) The absence of manufacturer warranty. (D) Suspension... displacement greater than 70 cc, the minimum useful life is 10,000 kilometers or five years, whichever comes... minimum useful life is 5,000 kilometers or five years, whichever comes first. You must specify a longer...

49 CFR Appendix A to Subpart D of... - Guidelines for Civil Penalties

Code of Federal Regulations, 2014 CFR

2014-10-01

... transportation in a self-certified packaging that has not been subjected to design qualification testing: 178.601... for transportation that minimally deviates from an approved design in a manner that does not impact... $5,000. 6. Failure to meet one or more of the general design requirements for a package used to ship...

49 CFR Appendix A to Subpart D of... - Guidelines for Civil Penalties

Code of Federal Regulations, 2013 CFR

2013-10-01

... transportation in a self-certified packaging that has not been subjected to design qualification testing: 178.601... for transportation that minimally deviates from an approved design in a manner that does not impact... $5,000. 6. Failure to meet one or more of the general design requirements for a package used to ship...

Short-term memory

NASA Astrophysics Data System (ADS)

Toulouse, G.

This is a rather bold attempt to bridge the gap between neuron structure and psychological data. We try to answer the question: Is there a relation between the neuronal connectivity in the human cortex (around 5,000) and the short-term memory capacity (7±2)? Our starting point is the Hopfield model (Hopfield 1982), presented in this volume by D.J. Amit.

Contractors Meeting in Propulsion Held in Boulder Colorado on June 10- 14, 1991

DTIC Science & Technology

1991-08-02

University Center for Chemical Engrg Blacksburg VA 24061 Gaithersburg MD 20899 (703)231-5950 Dr R G Rehm Dr Rolf D Reitz 3 National Institute of...AC/LKVE Sandia National Laboratories Edwards AFB CA 93523-5000 Livermore CA 94550 (805)275-5540 (415)294-2650 I AV525-5540 I Dr Charles Merkle Dr

10 CFR Appendix D to Part 835 - Surface Contamination Values

Code of Federal Regulations, 2011 CFR

2011-01-01

... emission or spontaneous fission) except Sr-90 and others noted above 5 1,000 5,000 Tritium and STCs 6 10... This category of radionuclides includes mixed fission products, including the Sr-90 which is present in them. It does not apply to Sr-90 which has been separated from the other fission products or mixtures...

78 FR 63460 - Government Owned Invention Available for Licensing, United States Patent, No. 7,837,654, Issued...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-10-24

... Delivery Device for Promoting Healing in Living Tissue'' AGENCY: Department of the Army, DoD. SUMMARY: The...,837,654 for ''Precision Sensing and Treatment Delivery Device for Promoting Healing in Living Tissue... Development and Engineering Command, ATTN: RDMR-S3I-CST, Bldg 5400, Redstone Arsenal, AL 35898- 5000. FOR...

Adaptation of Flux-Corrected Transport Algorithms for Modeling Dusty Flows.

DTIC Science & Technology

1983-12-20

Defense Comunications Agency Olcy Attn XLA Washington, DC 20305 01cy Attn nTW-2 (ADR CNW D I: Attn Code 240 for) Olcy Attn NL-STN O Library Olcy Attn...Library Olcy Attn TIC-Library Olcy Attn R Welch Olcy Attn M Johnson Los Alamos National Scientific Lab. Mail Station 5000 Information Science, Inc. P

High Value Talent: Identifying, Developing, and Retaining Naval Special Warfare’s Best Leaders

DTIC Science & Technology

2012-06-01

Retaining Naval Special Warfare’s Best Leaders 6. AUTHOR(S) Walter H. Allman, Jonathan M. Fussell, Marty D. Timmons 5. FUNDING NUMBERS 7. PERFORMING ...ORGANIZATION NAME(S) AND ADDRESS(ES) Naval Postgraduate School Monterey, CA 93943-5000 8. PERFORMING ORGANIZATION REPORT NUMBER 9. SPONSORING...5 1. High Performers ...................................................................................5 2. High Potentials

17 CFR Table 1 to Subpart E of... - Civil Monetary Penalty Inflation Adjustments

Code of Federal Regulations, 2012 CFR

2012-04-01

... monetary penalty description Year penalty amount was last set by law Original statutory maximum penalty amount Adjusted maximum penalty amount SECURITIES AND EXCHANGE COMMISSION: 15 USC 77t(d) FOR NATURAL PERSON 1990 $5,000 $5,500 FOR ANY OTHER PERSON 1990 50,000 55,000 FOR NATURAL PERSON/FRAUD 1990 50,000 55...

17 CFR Table 1 to Subpart E of... - Civil Monetary Penalty Inflation Adjustments

Code of Federal Regulations, 2011 CFR

2011-04-01

... monetary penalty description Year penalty amount was last set by law Original statutory maximum penalty amount Adjusted maximum penalty amount SECURITIES AND EXCHANGE COMMISSION: 15 USC 77t(d) FOR NATURAL PERSON 1990 $5,000 $5,500 FOR ANY OTHER PERSON 1990 50,000 55,000 FOR NATURAL PERSON/FRAUD 1990 50,000 55...

17 CFR Table 1 to Subpart E of... - Civil Monetary Penalty Inflation Adjustments

Code of Federal Regulations, 2013 CFR

2013-04-01

... monetary penalty description Year penalty amount was last set by law Original statutory maximum penalty amount Adjusted maximum penalty amount SECURITIES AND EXCHANGE COMMISSION: 15 USC 77t(d) FOR NATURAL PERSON 1990 $5,000 $5,500 FOR ANY OTHER PERSON 1990 50,000 55,000 FOR NATURAL PERSON/FRAUD 1990 50,000 55...

Update of the U.S. Army Research Institute’s Longitudinal Research Data Base of Officers

DTIC Science & Technology

1992-08-01

AIMS system. C-22 APPENDIX D AIMS CONTACT INFORMATION AIMS Project Office Administrative POC for AIMS Data Steven Veazey Commander (804) 878-5088 TRADOC...804) 727-4386 ATIN: ATOM-O ( Veazey ) Fort Monroe, VA 23651-5000 SYSCON HQ Williamsburg, VA 309 McLaws Circle Suite K Williamsburg, VA 23185 (804) 253

NPS Cubesat Launcher-Lite Sequencer

DTIC Science & Technology

2009-06-01

AND SUBTITLE NPS Cubesat Launcher-Lite Sequencer 6. AUTHOR(S) Harris, Anthony D. 5. FUNDING NUMBERS RSPXL 7. PERFORMING ORGANIZATION NAME(S) AND...ADDRESS(ES) Naval Postgraduate School Monterey, CA 93943-5000 8. PERFORMING ORGANIZATION REPORT NUMBER 9. SPONSORING /MONITORING AGENCY...international nanosatellite manufacturers. On April 28, 2009, Indian Space Research Organization launched 8 nanosatellites on the Polar Satellite Launch

Bulk Crystal Growth, and High-Resolution X-ray Diffraction Results of LiZnAs Semiconductor Material

NASA Astrophysics Data System (ADS)

Montag, Benjamin W.; Reichenberger, Michael A.; Sunder, Madhana; Ugorowski, Philip B.; Nelson, Kyle A.; Henson, Luke C.; McGregor, Douglas S.

2017-08-01

LiZnAs is being explored as a candidate for solid-state neutron detectors. The compact form, solid-state device would have greater efficiency than present day gas-filled 3He and 10BF3 detectors. Devices fabricated from LiZnAs having either natural Li (nominally 7.5% 6Li) or enriched 6Li (usually 95% 6Li) as constituent atoms may provide a material for compact high efficiency neutron detectors. The 6Li( n, t)4He reaction yields a total Q-value of 4.78 MeV, an energy larger than that of the 10B reaction, which can easily be identified above background radiations. LiZnAs material was synthesized by preparing equimolar portions of Li, Zn, and As sealed under vacuum (10-6 Torr) in quartz ampoules lined with boron nitride and subsequently reacted in a compounding furnace (Montag et al. in J Cryst Growth 412:103, 2015). The raw synthesized LiZnAs was purified by a static vacuum sublimation in quartz (Montag et al. in J Cryst Growth 438:99, 2016). Bulk crystalline LiZnAs ingots were grown from the purified material with a high-temperature Bridgman-style growth process described here. One of the largest LiZnAs ingots harvested was 9.6 mm in diameter and 4.2 mm in length. Samples were harvested from the ingot and were characterized for crystallinity using a Bruker AXS Inc. D8 AXS Inc. D2 CRYSO, energy dispersive x-ray diffractometer, and a Bruker AXS Inc. D8 DISCOVER, high-resolution x-ray diffractometer equipped with molybdenum radiation, Gobel mirror, four bounce germanium monochromator and a scintillation detector. The primary beam divergence was determined to be 0.004°, using a single crystal Si standard. The x-ray based characterization revealed that the samples nucleated in the (110) direction and a high-resolution open detector rocking curve recorded on the (220) LiZnAs yielded a full width at half maximum (FWHM) of 0.235°. Sectional pole figures using off-axis reflections of the (211) LiZnAs confirmed in-plane ordering, and also indicated the presence of multiple domains. The LiZnAs bulk crystals exhibited a Primitive Cubic Bravais lattice instead of the commonly reported Face-centered Cubic Bravais lattice. The lattice constant was determined to be 5.5146 ± 0.0003 Å.

47 CFR 32.5000 - Basic local service revenue.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 47 Telecommunication 2 2011-10-01 2011-10-01 false Basic local service revenue. 32.5000 Section 32.5000 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) COMMON CARRIER SERVICES UNIFORM SYSTEM OF ACCOUNTS FOR TELECOMMUNICATIONS COMPANIES Instructions For Revenue Accounts § 32.5000 Basic...

47 CFR 32.5000 - Basic local service revenue.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 47 Telecommunication 2 2014-10-01 2014-10-01 false Basic local service revenue. 32.5000 Section 32.5000 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) COMMON CARRIER SERVICES UNIFORM SYSTEM OF ACCOUNTS FOR TELECOMMUNICATIONS COMPANIES Instructions For Revenue Accounts § 32.5000 Basic...

47 CFR 32.5000 - Basic local service revenue.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 47 Telecommunication 2 2013-10-01 2013-10-01 false Basic local service revenue. 32.5000 Section 32.5000 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) COMMON CARRIER SERVICES UNIFORM SYSTEM OF ACCOUNTS FOR TELECOMMUNICATIONS COMPANIES Instructions For Revenue Accounts § 32.5000 Basic...

New large volume hydrothermal reaction cell for studying chemical processes under supercritical hydrothermal conditions using time-resolved in situ neutron diffraction.

PubMed

Ok, Kang Min; O'Hare, Dermot; Smith, Ronald I; Chowdhury, Mohammed; Fikremariam, Hanna

2010-12-01

The design and testing of a new large volume Inconel pressure cell for the in situ study of supercritical hydrothermal syntheses using time-resolved neutron diffraction is introduced for the first time. The commissioning of this new cell is demonstrated by the measurement of the time-of-flight neutron diffraction pattern for TiO(2) (Anatase) in supercritical D(2)O on the POLARIS diffractometer at the United Kingdom's pulsed spallation neutron source, ISIS, Rutherford Appleton Laboratory. The sample can be studied over a wide range of temperatures (25-450 °C) and pressures (1-355 bar). This novel apparatus will now enable us to study the kinetics and mechanisms of chemical syntheses under extreme environments such as supercritical water, and in particular to study the crystallization of a variety of technologically important inorganic materials.

29 CFR 500.0 - Introduction.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 29 Labor 3 2010-07-01 2010-07-01 false Introduction. 500.0 Section 500.0 Labor Regulations Relating to Labor (Continued) WAGE AND HOUR DIVISION, DEPARTMENT OF LABOR REGULATIONS MIGRANT AND SEASONAL AGRICULTURAL WORKER PROTECTION General Provisions § 500.0 Introduction. (a) The Migrant and Seasonal...

Neutron apparatus for measuring strain in composites

DOEpatents

Kupperman, David S.; Majumdar, Saurindranath; Faber, Jr., John F.; Singh, J. P.

1990-01-01

A method and apparatus for orienting a pulsed neutron source and a multi-angle diffractometer toward a sample of a ceramic-matrix or metal-matrix composite so that the measurement of internal strain (from which stress is calculated) is reduced to uncomplicated time-of-flight measurements.

“Resting” CBF in the Epileptic Baboon: Correlation with Ketamine Dose and Interictal Epileptic Discharges

PubMed Central

Szabó, C. Ákos; Narayana, Shalini; Franklin, Crystal; Knape, Koyle D.; Davis, M. Duff; Fox, Peter T.; Leland, M. Michelle; Williams, Jeff T.

2011-01-01

Background Photosensitive epileptic (SZ) baboons demonstrate different cerebral blood flow (CBF) activation patterns from asymptomatic controls (CTL) during intermittent light stimulation (ILS). This study compares “resting” CBF between PS and CTL animals, and CBF correlations with ketamine dose and interictal epileptic discharges (IEDs) between PS and CTL animals. Methods Continuous intravenous ketamine was administered to eight PS and eight CTL baboons (matched for gender and weight), and maintained at subanesthetic doses (4.8–14.6 mg/kg/hr). Three resting H215O-PET studies were attempted in each animal (CTI/Siemens HR+ scanner). Images were acquired in 3D mode (63 contiguous slices, 2.4 mm thickness). PET images were co-registered with MRI images (3T Siemens Trio, T1-weighted 3D Turboflash sequence, TE/TR/TI = 3.04/2100/785 msec, flip angle=13 degrees). EEG was used to monitor depth of sedation and for quantification of IED rates. Regional CBF was compared between PS and CTL groups and correlations were analyzed for ketamine dose and IED rates. Results When subsets of animals of either group, receiving similar doses of ketamine were compared, PS animals demonstrated relative CBF increases in the occipital lobes and decreases in the frontal lobes. Correlation analyses with ketamine dose confirmed the frontal and occipital lobe changes in the PS animals. The negative correlations of CBF with ketamine dose and IED rate overlapped frontally. While frontal lobe CBF was also negatively correlated with IED rate, positive correlations were found in the parietal lobe. Conclusions “Resting” CBF differs between PS and CTL baboons. Correlation analyses of CBF and ketamine dose reveal that occipital lobe CBF increases and frontal lobe in PS animals are driven by ketamine. While frontal lobe CBF decreases may be related to ketamine’s propensity to activate IEDs, positive CBF correlations with IED rate suggest involvement of the parietal lobes in their generation. PMID:18801644

Point-of-Care Versus Central Laboratory Measurements of Hemoglobin, Hematocrit, Glucose, Bicarbonate and Electrolytes: A Prospective Observational Study in Critically Ill Patients.

PubMed

Allardet-Servent, Jérôme; Lebsir, Melissa; Dubroca, Christian; Fabrigoule, Martine; Jordana, Sylvie; Signouret, Thomas; Castanier, Matthias; Thomas, Guillemette; Soundaravelou, Rettinavelou; Lepidi, Anne; Delapierre, Laurence; Penaranda, Guillaume; Halfon, Philippe; Seghboyan, Jean-Marie

2017-01-01

Rapid detection of abnormal biological values using point-of-care (POC) testing allows clinicians to promptly initiate therapy; however, there are concerns regarding the reliability of POC measurements. We investigated the agreement between the latest generation blood gas analyzer and central laboratory measurements of electrolytes, bicarbonate, hemoglobin, hematocrit, and glucose. 314 paired samples were collected prospectively from 51 critically ill patients. All samples were drawn simultaneously in the morning from an arterial line. BD Vacutainer tubes were analyzed in the central laboratory using Beckman Coulter analyzers (AU 5800 and DxH 800). BD Preset 3 ml heparinized-syringes were analyzed immediately in the ICU using the POC Siemens RAPIDPoint 500 blood gas system. We used CLIA proficiency testing criteria to define acceptable analytical performance and interchangeability. Biases, limits of agreement (±1.96 SD) and coefficients of correlation were respectively: 1.3 (-2.2 to 4.8 mmol/L, r = 0.936) for sodium; 0.2 (-0.2 to 0.6 mmol/L, r = 0.944) for potassium; -0.9 (-3.7 to 2 mmol/L, r = 0.967) for chloride; 0.8 (-1.9 to 3.4 mmol/L, r = 0.968) for bicarbonate; -11 (-30 to 9 mg/dL, r = 0.972) for glucose; -0.8 (-1.4 to -0.2 g/dL, r = 0.985) for hemoglobin; and -1.1 (-2.9 to 0.7%, r = 0.981) for hematocrit. All differences were below CLIA cut-off values, except for hemoglobin. Compared to central Laboratory analyzers, the POC Siemens RAPIDPoint 500 blood gas system satisfied the CLIA criteria of interchangeability for all tested parameters, except for hemoglobin. These results are warranted for our own procedures and devices. Bearing these restrictions, we recommend clinicians to initiate an appropriate therapy based on POC testing without awaiting a control measurement.

Point-of-Care Versus Central Laboratory Measurements of Hemoglobin, Hematocrit, Glucose, Bicarbonate and Electrolytes: A Prospective Observational Study in Critically Ill Patients

PubMed Central

Lebsir, Melissa; Dubroca, Christian; Fabrigoule, Martine; Jordana, Sylvie; Signouret, Thomas; Castanier, Matthias; Thomas, Guillemette; Soundaravelou, Rettinavelou; Lepidi, Anne; Delapierre, Laurence; Penaranda, Guillaume; Halfon, Philippe; Seghboyan, Jean-Marie

2017-01-01

Introduction Rapid detection of abnormal biological values using point-of-care (POC) testing allows clinicians to promptly initiate therapy; however, there are concerns regarding the reliability of POC measurements. We investigated the agreement between the latest generation blood gas analyzer and central laboratory measurements of electrolytes, bicarbonate, hemoglobin, hematocrit, and glucose. Methods 314 paired samples were collected prospectively from 51 critically ill patients. All samples were drawn simultaneously in the morning from an arterial line. BD Vacutainer tubes were analyzed in the central laboratory using Beckman Coulter analyzers (AU 5800 and DxH 800). BD Preset 3 ml heparinized-syringes were analyzed immediately in the ICU using the POC Siemens RAPIDPoint 500 blood gas system. We used CLIA proficiency testing criteria to define acceptable analytical performance and interchangeability. Results Biases, limits of agreement (±1.96 SD) and coefficients of correlation were respectively: 1.3 (-2.2 to 4.8 mmol/L, r = 0.936) for sodium; 0.2 (-0.2 to 0.6 mmol/L, r = 0.944) for potassium; -0.9 (-3.7 to 2 mmol/L, r = 0.967) for chloride; 0.8 (-1.9 to 3.4 mmol/L, r = 0.968) for bicarbonate; -11 (-30 to 9 mg/dL, r = 0.972) for glucose; -0.8 (-1.4 to -0.2 g/dL, r = 0.985) for hemoglobin; and -1.1 (-2.9 to 0.7%, r = 0.981) for hematocrit. All differences were below CLIA cut-off values, except for hemoglobin. Conclusions Compared to central Laboratory analyzers, the POC Siemens RAPIDPoint 500 blood gas system satisfied the CLIA criteria of interchangeability for all tested parameters, except for hemoglobin. These results are warranted for our own procedures and devices. Bearing these restrictions, we recommend clinicians to initiate an appropriate therapy based on POC testing without awaiting a control measurement. PMID:28072822

Projets et développemepts en cryoélectrotechnique

NASA Astrophysics Data System (ADS)

Tixador, P.; Laumond, Y.

1991-02-01

The use of superconductivity in electrical engineering is reviewed. It deals with low T_c superconductors as only applications under development are considered. The article describes first the " classical " uses under constant or slow varying magnetic field: coils for Superconducting Magnetic Energy Storage, they are expected as a power system stabilizer and not only as a energy storage system. The present status of superconducting field a.c. generators is reviewed and the different programs over the world are described: in Germany (KWU/Siemens), in UDSSR, and in Japan where the program Super GM is led by the Engineering Research Association for Superconductive Generation Equipment and Materials. After a description of ultra-fine multifilamentary wires for 50-60 Hz use their applications are reviewed: electrical machines, above all fully superconducting a.c. generators, transformers and limiters based on the superconducting-normal transition above the critical current. Les diverses applications de la supraconductivité en électrotechnique ou courants forts sont passées en revue. Comme il s'agit de développements en cours, seule la supraconductivité à basse température est considérée. Les applications " classiques " des supraconducteurs sont abordées en premier. Ce sont les bobines de stockage (S.M.E.S.), qui peuvent fonctionner également en régulateur, les alternateurs à inducteur supraconducteur (SC) avec les programmes japonais (super GM), allemand (KWU Siemens) et soviétique, sans oublier la lévitation magnétique... Ensuite, après un bref rappel sur les multifilamentaires ultrafins utilisables aux fréquences industrielles apparus en 1983, l'article considère les applications de ces nouveaux conducteurs SC : machines électriques avec les alternateurs entièrement supraconducteurs surtout, transformateurs et enfin limiteurs qui utilisent le phénomène original de la transition supra/normal pour limiter les surintensités.

A Neutron Diffractometer for a Long Pulsed Neutron Source

NASA Astrophysics Data System (ADS)

Sokol, Paul; Wang, Cailin

Long pulsed neutron sources are being actively developed as small university based sources and are being considered for the next generation of high powered sources, such as the European Neutron Source (ESS) and the Spallation Neutron Source (SNS) second target station. New instrumentation concepts will be required to effectively utilize the full spectrum of neutrons generated by these sources. Neutron diffractometers, which utilize time-of-flight (TOF) techniques for wavelength resolution, are particularly problematic. We describe an instrument for a long pulsed source that provides resolution comparable to that obtained on short pulsed sources without the need of long incident flight paths. We accomplish this by utilizing high speed choppers to impose a time structure on the spectrum of incident neutrons. By strategically positioning these choppers the response matrix assumes a convenient form that can be deconvoluted from the measured TOF spectrum to produce the diffraction pattern of the sample. We compare the performance of this instrument to other possible diffraction instruments that could be utilized on a long pulsed source.

Modeling of the focusing device and the elliptical neutron guide for the DN-6 diffractometer at IBR-2 reactor

NASA Astrophysics Data System (ADS)

Belushkin, A. V.; Manoshin, S. A.; Kozlenko, D. P.; Kichanov, S. E.

2018-06-01

Possible options for modernization of the neutron beam forming system of the DN-6 diffractometer for the study of crystal and magnetic structures of microsamples at high pressures are being considered. It was demonstrated that for samples with the cross-section not exceeding 5 × 5 mm2 the most efficient option would be the use of an elliptical neutron guide. It allows to deliver neutrons for large distances from the source to samples with minimal losses using, as a rule, just one neutron reflection per dimension i.e. one at a side and one at top or bottom. For the present moment due to technical difficulties of such option realization, the simplified solution was proposed. At the end of the curved neutron guide it is planned to install a vertical plane focusing 7-meter-long parabolic section. Such a modernization will increase the neutron flux at the sample by a factor 1.5-3.5 and reduce respectively the typical measurement times.

Development of a cryogenic load frame for the neutron diffractometer at Takumi in Japan Proton Accelerator Research Complex

NASA Astrophysics Data System (ADS)

Jin, Xinzhe; Nakamoto, Tatsushi; Harjo, Stefanus; Hemmi, Tsutomu; Umeno, Takahiro; Ogitsu, Toru; Yamamoto, Akira; Sugano, Michinaka; Aizawa, Kazuya; Abe, Jun; Gong, Wu; Iwahashi, Takaaki

2013-06-01

To prepare for projects such as the Large Hadron Collider upgrade, International Thermonuclear Experimental Reactor and Demonstration reactor, it is important to form a clear understanding of stress-strain properties of the materials that make up superconducting magnets. Thus, we have been studying the mechanical properties of superconducting wires using neutron diffraction measurements. To simulate operational conditions such as temperature, stress, and strain, we developed a cryogenic load frame for stress-strain measurements of materials using a neutron diffractometer at Japan Proton Accelerator Research Complex (J-PARC) Takumi beam line. The maximum load that can be applied to a sample using an external driving machine is 50 kN. Using a Gifford-MacMahon cryocooler, samples can be measured down to temperatures below 10 K when loaded. In the present paper, we describe the details of the cryogenic load frame with its test results by using type-304 stainless steel wire.

A 4 Tesla Superconducting Magnet Developed for a 6 Circle Huber Diffractometer at the XMaS Beamline

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thompson, P. B. J.; Brown, S. D.; Bouchenoire, L.

2007-01-19

We report here on the development and testing of a 4 Tesla cryogen free superconducting magnet designed to fit within the Euler cradle of a 6 circle Huber diffractometer, allowing scattering in both the vertical and horizontal planes. The geometry of this magnet allows the field to be applied in three orientations. The first being along the beam direction, the second with the field transverse to the beam direction a horizontal plane and finally the field can be applied vertically with respect to the beam. The magnet has a warm bore and an open geometry of 180 deg. , allowingmore » large access to reciprocal space. A variable temperature insert has been developed, which is capable of working down to a temperature of 1.7 K and operating over a wide range of angles whilst maintaining a temperature stability of a few mK. Initial ferromagnetic diffraction measurements have been carried out on single crystal Tb and Dy samples.« less

Hippo/crates-in-situ deformation strain and testure studies using neutron time-of-flight diffraction.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vogel, S. C.; Hartig, C.; Brissier, T. D.

2005-01-01

In situ deformation studies by diffraction allow studying of deformation mechanisms and provide valuable data to validate and improve deformation models. In particular, deformation studies using time-of-flight neutrons provide averages over large numbers of grains and allow to probing the response of lattice planes parallel and perpendicular to the applied load simultaneously. In this paper we describe the load-frame CRATES, designed for the HIPPO neutron time-of-flight diffractometer at LANSCE. The HIPPO/CRATES combination allows probing up to 20 diffraction vectors simultaneously and provides rotation of the sample in the beam while under load. With this, deformation texture, i.e. the change ofmore » grain orientation due to plastic deformation, or strain pole figures may be measured. We report initial results of a validation experiment, comparing deformation of a Zircaloy specimen measured using the NPD neutron diffractometer with results obtained for the same material using HIPPO/CRATES.« less

A furnace with rotating load frame for in situ high temperature deformation and creep experiments in a neutron diffraction beam line

DOE Office of Scientific and Technical Information (OSTI.GOV)

Reiche, H. M.; New Mexico State University, Las Cruces, New Mexico 88003; Vogel, S. C.

2012-05-15

A resistive furnace combined with a load frame was built that allows for in situ neutron diffraction studies of high temperature deformation, in particular, creep. A maximum force of 2700 N can be applied at temperatures up to 1000 deg. C. A load control mode permits studies of, e.g., creep or phase transformations under applied uni-axial stress. In position control, a range of high temperature deformation experiments can be achieved. The examined specimen can be rotated up to 80 deg. around the vertical compression axis allowing texture measurements in the neutron time-of-flight diffractometer HIPPO (High Pressure - Preferred Orientation). Wemore » present results from the successful commissioning, deforming a Zr-2.5 wt.% Nb cylinder at 975 deg. C. The device is now available for the user program of the HIPPO diffractometer at the LANSCE (Los Alamos Neutron Science Center) user facility.« less

Development of a cryogenic load frame for the neutron diffractometer at Takumi in Japan Proton Accelerator Research Complex

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jin, Xinzhe; Nakamoto, Tatsushi; Ogitsu, Toru

2013-06-15

To prepare for projects such as the Large Hadron Collider upgrade, International Thermonuclear Experimental Reactor and Demonstration reactor, it is important to form a clear understanding of stress-strain properties of the materials that make up superconducting magnets. Thus, we have been studying the mechanical properties of superconducting wires using neutron diffraction measurements. To simulate operational conditions such as temperature, stress, and strain, we developed a cryogenic load frame for stress-strain measurements of materials using a neutron diffractometer at Japan Proton Accelerator Research Complex (J-PARC) Takumi beam line. The maximum load that can be applied to a sample using an externalmore » driving machine is 50 kN. Using a Gifford-MacMahon cryocooler, samples can be measured down to temperatures below 10 K when loaded. In the present paper, we describe the details of the cryogenic load frame with its test results by using type-304 stainless steel wire.« less

Development of a cryogenic load frame for the neutron diffractometer at Takumi in Japan Proton Accelerator Research Complex.

PubMed

Jin, Xinzhe; Nakamoto, Tatsushi; Harjo, Stefanus; Hemmi, Tsutomu; Umeno, Takahiro; Ogitsu, Toru; Yamamoto, Akira; Sugano, Michinaka; Aizawa, Kazuya; Abe, Jun; Gong, Wu; Iwahashi, Takaaki

2013-06-01

To prepare for projects such as the Large Hadron Collider upgrade, International Thermonuclear Experimental Reactor and Demonstration reactor, it is important to form a clear understanding of stress-strain properties of the materials that make up superconducting magnets. Thus, we have been studying the mechanical properties of superconducting wires using neutron diffraction measurements. To simulate operational conditions such as temperature, stress, and strain, we developed a cryogenic load frame for stress-strain measurements of materials using a neutron diffractometer at Japan Proton Accelerator Research Complex (J-PARC) Takumi beam line. The maximum load that can be applied to a sample using an external driving machine is 50 kN. Using a Gifford-MacMahon cryocooler, samples can be measured down to temperatures below 10 K when loaded. In the present paper, we describe the details of the cryogenic load frame with its test results by using type-304 stainless steel wire.

Molecular Transmission Band Models for LOWTRAN

DTIC Science & Technology

1986-12-31

Lo en z a:. a: r-IJ’l (\\J 0 -5.0 -4.0 -3.0 -2.0 -1.0 1.0 2.0 LOG 10 (ChJ) Fig. 2. Composite Plot of the Transmission Functions (Eq...C02 and HzO, IV. Shap•s of Collisioned - Broadened co2 Linea ", J. Opt. Soc. of Am., 59, 267 (1969). 29. D. E. Bureh, J.D. Pembrook, and D. A...O::::J’ a: I (L (X) _Jg V1 a: a:tD I t- u Wo (LO en . co I 100.0 140.0 180.0 220.0 260.0 300.0 340.0 380.0 420.0 460.0 500.0 540.0 580.0

Exponential Characteristic Spatial Quadrature for Discrete Ordinates Neutral Particle Transport in Slab Geometry

DTIC Science & Technology

1992-03-01

left bdy = 0 vacuum current incident at left boundary = I type of current incident at left bdy = 0 isotropic surface Src region# cR SigmaR SourceR nc...0 type of current incident at left bdy = 0 isotropic surface Src region# cR SigmaR SourceR nc Right Bdy 1 0.5000 .3OD+00 0.0000D+00 256. 16.0000 2... SigmaR SourceR nc Right Bdy 1 0.1000 1.0000D+00 0.0000D+00 256. 16.0000 2 0.9500 1.0(OOD+00 1.0000D+00 256. 32.0000 type of right bdy = 0 vacuum current

Comparison of Two Different Ultrasound Devices Using Strain Elastography Technology in the Diagnosis of Breast Lesions Related to the Histologic Results.

PubMed

Farrokh, André; Schaefer, Fritz; Degenhardt, Friedrich; Maass, Nicolai

2018-05-01

This study was conducted to provide evidence that elastograms of two different devices and different manufacturers using the same technical approach provide the same diagnoses. A total of 110 breast lesions were prospectively analysed by two experts in ultrasound, using the strain elastography function from two different manufacturers (Hitachi HI-RTE, Hitachi Medical Systems, Wiesbaden, Germany; and Siemens eSie Touch, Siemens Medical Systems, Erlangen, Germany). Results were compared with the histopathologic results. Applying the Bowker test of symmetry, no statistically significant difference between the two elastography functions of these two devices was found (p = 0.120). The Cohen's kappa of k = 0.591 showed moderate strength of agreement between the two elastograms. The two examiners yielded moderate strength of agreement analysing the elastograms (Hitachi HI-RTE, k = 0.478; Siemens eSie Touch, k = 0.441). In conclusion, evidence is provided that elastograms of the same lesion generated by two different ultrasound devices equipped with a strain elastography function do not significantly differ. Copyright © 2018 World Federation for Ultrasound in Medicine and Biology. Published by Elsevier Inc. All rights reserved.

41 CFR 109-28.5000 - Scope of subpart.

Code of Federal Regulations, 2010 CFR

2010-07-01

...-STORAGE AND DISTRIBUTION 28.50-Management of Equipment Held for Future Projects § 109-28.5000 Scope of... 41 Public Contracts and Property Management 3 2010-07-01 2010-07-01 false Scope of subpart. 109-28.5000 Section 109-28.5000 Public Contracts and Property Management Federal Property Management...

12 CFR 7.5000 - Scope.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 12 Banks and Banking 1 2010-01-01 2010-01-01 false Scope. 7.5000 Section 7.5000 Banks and Banking COMPTROLLER OF THE CURRENCY, DEPARTMENT OF THE TREASURY BANK ACTIVITIES AND OPERATIONS Electronic Activities § 7.5000 Scope. This subpart applies to a national bank's use of technology to deliver services and...

12 CFR 7.5000 - Scope.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 12 Banks and Banking 1 2011-01-01 2011-01-01 false Scope. 7.5000 Section 7.5000 Banks and Banking COMPTROLLER OF THE CURRENCY, DEPARTMENT OF THE TREASURY BANK ACTIVITIES AND OPERATIONS Electronic Activities § 7.5000 Scope. This subpart applies to a national bank's use of technology to deliver services and...

49 CFR Appendix A to Part 231 - Schedule of Civil Penalties 1

Code of Federal Regulations, 2011 CFR

2011-10-01

... 120.B1Brake Step or Brace Bent 2,500 5,000 120.B2Brake Step or Wrong Dimensions 2,500 5,000 120...,000 124.B1Running Board Bent to the Extent that It is Unsafe 2,500 5,000 124.B2Running Board Wrong... 126.B1End Platform or Brace Bent 2,500 5,000 126.B2End Platform Wrong Dimensions 2,500 5,000 126.C1End...

40 CFR 421.115 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Ammonia (as N) 82.910 36.450 Fluoride 21.770 12.440 (b) Subpart K—Solvent Extraction Raffinate. PSES... pounds) of concentrate digested Lead 2.592 1.203 Zinc 9.442 3.888 Ammonia (as N) 1,233.000 542.5000... concentrate digested Lead .069 .032 Zinc .251 .103 Ammonia (as N) 32.790 14.420 Fluoride 8.610 4.920 (d...

40 CFR 421.115 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Ammonia (as N) 82.910 36.450 Fluoride 21.770 12.440 (b) Subpart K—Solvent Extraction Raffinate. PSES... pounds) of concentrate digested Lead 2.592 1.203 Zinc 9.442 3.888 Ammonia (as N) 1,233.000 542.5000... concentrate digested Lead .069 .032 Zinc .251 .103 Ammonia (as N) 32.790 14.420 Fluoride 8.610 4.920 (d...

40 CFR 421.115 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Ammonia (as N) 82.910 36.450 Fluoride 21.770 12.440 (b) Subpart K—Solvent Extraction Raffinate. PSES... pounds) of concentrate digested Lead 2.592 1.203 Zinc 9.442 3.888 Ammonia (as N) 1,233.000 542.5000... concentrate digested Lead .069 .032 Zinc .251 .103 Ammonia (as N) 32.790 14.420 Fluoride 8.610 4.920 (d...

40 CFR 421.115 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Ammonia (as N) 82.910 36.450 Fluoride 21.770 12.440 (b) Subpart K—Solvent Extraction Raffinate. PSES... pounds) of concentrate digested Lead 2.592 1.203 Zinc 9.442 3.888 Ammonia (as N) 1,233.000 542.5000... concentrate digested Lead .069 .032 Zinc .251 .103 Ammonia (as N) 32.790 14.420 Fluoride 8.610 4.920 (d...

40 CFR 421.115 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Ammonia (as N) 82.910 36.450 Fluoride 21.770 12.440 (b) Subpart K—Solvent Extraction Raffinate. PSES... pounds) of concentrate digested Lead 2.592 1.203 Zinc 9.442 3.888 Ammonia (as N) 1,233.000 542.5000... concentrate digested Lead .069 .032 Zinc .251 .103 Ammonia (as N) 32.790 14.420 Fluoride 8.610 4.920 (d...

40 CFR 112.3 - Requirement to prepare and implement a Spill Prevention, Control, and Countermeasure Plan.

Code of Federal Regulations, 2014 CFR

2014-07-01

....S. gallons within any twelve month period in the three years prior to the SPCC Plan self... months after you begin operations. (c) [Reserved] (d) Except as provided in § 112.6, a licensed... section and has no individual aboveground oil storage container with a capacity greater than 5,000 U.S...

40 CFR 112.3 - Requirement to prepare and implement a Spill Prevention, Control, and Countermeasure Plan.

Code of Federal Regulations, 2013 CFR

2013-07-01

....S. gallons within any twelve month period in the three years prior to the SPCC Plan self... months after you begin operations. (c) [Reserved] (d) Except as provided in § 112.6, a licensed... section and has no individual aboveground oil storage container with a capacity greater than 5,000 U.S...

26 CFR 41.4483-3 - Exemption for trucks used for 5,000 or fewer miles and agricultural vehicles used for 7,500 or...

Code of Federal Regulations, 2010 CFR

2010-04-01

.... (D) Use of a highway motor vehicle in connection with the operation, management, conservation... it is used in connection with the operation, management, conservation, improvement, or maintenance of... by a processing operation from its raw or natural state. For example, juice which has been extracted...

17 CFR Table 1 to Subpart E of... - Civil Monetary Penalty Inflation Adjustments

Code of Federal Regulations, 2014 CFR

2014-04-01

... monetary penalty description Year penalty amount was last set by law Original statutory maximum penalty amount Adjusted maximum penalty amount SECURITIES AND EXCHANGE COMMISSION: 15 U.S.C. 77t(d) FOR NATURAL PERSON 1990 $5,000 $5,500 FOR ANY OTHER PERSON 1990 50,000 55,000 FOR NATURAL PERSON/FRAUD 1990 50,000 55...

Research Comparing Charter Schools and Traditional Public Schools. Literature Review

ERIC Educational Resources Information Center

Blazer, Christie

2010-01-01

During the 2008-09 school year, over 5,000 charter schools operated in 40 states and Washington, D.C. and were attended by over 1.5 million students, or about three percent of the nation's public school students. Although the first U.S. charter schools opened in 1992, debate continues over whether they provide students with a better education than…

23 CFR Appendix D to Subpart A of... - Guidance Criteria for Evaluating Requests for Modifications to the National Highway System

Code of Federal Regulations, 2011 CFR

2011-04-01

... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION PLANNING AND RESEARCH HIGHWAY SYSTEMS Federal-aid Highway Systems Pt... volumes, or daily vehicular traffic on one or more principal routes that serve the intermodal facility... and ride lots with more than 500 vehicle parking spaces, or 5,000 daily bus or rail passengers, with...

(Re)Framing the Politics of Educational Discourse: An Investigation of the Title I School Improvement Grant Program of 2009

ERIC Educational Resources Information Center

Carpenter, Bradley Wayne

2011-01-01

Of the numerous public policy debates currently taking place throughout the United States, perhaps no issue receives more attention than the persistence of "chronically" low-performing public schools. As of 2009, approximately 5,000 schools--5% of the nation's total--qualified as chronically low performing (Duncan, 2009d). Certainly,…

78 FR 6189 - Federal Acquisition Regulation; Unallowability of Costs Associated With Foreign Contractor Excise...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-01-29

... 9000-AM13 Federal Acquisition Regulation; Unallowability of Costs Associated With Foreign Contractor... contractor in order to reimburse the tax imposed (26 U.S.C. 5000C Note). On February 22, 2012, DoD, GSA, and... with the statute, FAR 31.205-41 is amended to inform the Government and contractors that the costs of...

Integration of a High Sensitivity MEMS Directional Sound Sensor With Readout Electronics

DTIC Science & Technology

2012-12-01

Readout Electronics 5. FUNDING NUMBERS 6. AUTHOR(S) John D. Roth 7. PERFORMING ORGANIZATION NAME(S) AND ADDRESS(ES) Naval Postgraduate School...Monterey, CA 93943–5000 8. PERFORMING ORGANIZATION REPORT NUMBER 9. SPONSORING /MONITORING AGENCY NAME(S) AND ADDRESS(ES) Space and Naval Warfare...1   1.   The Anatomy of the Ormia Ochracea Hearing Organ

Test and Evaluation Management Guide

DTIC Science & Technology

1988-03-01

of the acquisition community at large, whose comments, suggestions, and materials were helpful in completing this project . The ...analysis are particularly useful in the early stages of development to provide early projections before system hardware is available. These methods are also...Statement is prescribed by DoD Instruction 5000.2. In summary, it contains the following: o A description of the mission need 0 The projected

Optimization of the formation of embedded multicellular spheroids of MCF-7 cells: How to reliably produce a biomimetic 3D model.

PubMed

Zhang, Wenli; Li, Caibin; Baguley, Bruce C; Zhou, Fang; Zhou, Weisai; Shaw, John P; Wang, Zhen; Wu, Zimei; Liu, Jianping

2016-12-15

To obtain a multicellular MCF-7 spheroid model to mimic the three-dimensional (3D) of tumors, the microwell liquid overlay (A) and hanging-drop/agar (B) methods were first compared for their technical parameters. Then a method for embedding spheroids within collagen was optimized. For method A, centrifugation assisted cells form irregular aggregates but not spheroids. For method B, an extended sedimentation period of over 24 h for cell suspensions and increased viscosity of the culture medium using methylcellulose were necessary to harvest a dense and regular cell spheroid. When the number was less than 5000 cells/drop, embedded spheroids showed no tight cores and higher viability than the unembedded. However, above 5000 cells/drop, cellular viability of embedded spheroids was not significantly different from unembedded spheroids and cells invading through the collagen were in a sun-burst pattern with tight cores. Propidium Iodide staining indicated that spheroids had necrotic cores. The doxorubicin cytotoxicity demonstrated that spheroids were less susceptible to DOX than their monolayer cells. A reliable and reproducible method for embedding spheroids using the hanging-drop/agarose method within collagen is described herein. The cell culture model can be used to guide experimental manipulation of 3D cell cultures and to evaluate anticancer drug efficacy. Copyright © 2016 Elsevier Inc. All rights reserved.

Diagnostic Performance of Serum IgG4 Levels in Patients With IgG4-Related Disease

PubMed Central

Yu, Kuang-Hui; Chan, Tien-Ming; Tsai, Ping-Han; Chen, Ching-Hui; Chang, Pi-Yueh

2015-01-01

Abstract The aim of this study is to study the clinical features and diagnostic performance of IgG4 in Chinese populations with IgG4-related diseases (IgG4-RDs). The medical records of 2901 adult subjects who underwent serum IgG4 level tests conducted between December 2007 and May 2014 were reviewed. Serum concentrations of IgG4 were measured in 2901 cases, including 161 (5.6%) patients with IgG4-RD and 2740 (94.4%) patients without IgG4-RD (non-IgG4-RD group). The mean age of the IgG4-RD patients was 58.4 ± 16.1 years (range: 21–87), and 48 (29.8%) were women. The mean serum IgG4 level was significantly much higher in IgG4-RD patients than in non-IgG4-RD (1062.6 vs 104.3 mg/dL, P < 0.001) participants. For IgG4 >135 mg/dL, the sensitivity, specificity, positive predictive value (PPV), negative predictive value (NPV), likelihood ratio (LR)+, and LR− were 86%, 77%, 18%, 99%, 3.70, and 0.19, respectively. When the upper limit of normal was doubled for an IgG4 >270 mg/dL, the corresponding data were 75%, 94%, 43%, 98%, 12.79, and 0.26, respectively. For IgG4 >405 mg/dL (tripling the upper limit of normal), the corresponding data were 62%, 98%, 68%, 98%, 37.00, and 0.39, respectively. When calculated according to the manufacturer's package insert cutoff (>201 mg/dL) for the diagnosis of IgG4-RD, the corresponding sensitivity, specificity, PPV, NPV, LR+, and LR− were 80%, 89%, 29%, 99%, 7.00, and 0.23, respectively. For IgG4 >402 mg/dL (>2× the upper limit of the normal range), the corresponding data were 62%, 98%, 68%, 98%, 36.21, and 0.39, respectively. For IgG4 >603 mg/dL (>3× the upper limit of the normal range), the corresponding data were 50%, 99%, 84%, 97%, 90.77 and 0.51, respectively. The optimal cutoff value of serum IgG4 (measured by nephelometry using a Siemens BN ProSpec instrument and Siemens reagent) for the diagnosis of IgG4-RD was 248 mg/dL, the sensitivity and specificity were 77.6% and 92.8%, respectively. The present study demonstrated that 2 or 3 times the upper limit of the manufacturer's reference range of the IgG4 level was a useful marker for the diagnosis of various types of IgG4-RD and the optimal cutoff level was 248 mg/dL. PMID:26469909

Crystallization behavior of polyamide-6 microcellular nanocomposites

Treesearch

Mingjun Yuan; Lih-Sheng Turng; Shaoqin Gong; Andreas Winardi

2004-09-01

The crystallization behaviors of polyamide-6 (PA-6) and its nanocomposites undergoing the microcellular injection molding process are studied using Transmission Electron Microscopy (TEM), X-ray Diffractometer (XRD), Polarized Optical Microscopy (POM), and Differential Scanning Calorimetry (DSC). The relationships among the morphology, the mechanical property of the...

Impact of Herbivory and Plant Competition on the Growth of Hydrilla in Small Ponds

DTIC Science & Technology

2007-02-01

pond (6m x 6m with a depth of 1.3 m) was lined with 45-mil synthetic EPDM rubber (Ethylene propylene diene monomer, Firestone, Akron, OH...3000 4000 5000 6000 Competition No Competition % D am ag ed L ea ve s 0 10 20 30 40 50 60 Jul-01 Sep-01 Nov-01 Jan-02 Mar-02 May-02 Jul-02 Sept-02 Nox...02 Jan-03 Mar-03 May-03 % D am ag ed L ea ve s 0 10 20 30 40 50 60 No Competition Competition A B C D Figure 1. Number of immatures per kg in

Report of the Defense Science Board Summer Study on Joint Service Acquisition Programs

DTIC Science & Technology

1984-02-01

ENGINEERING Washington, D. C. 20301 r! OFFICE OF THE SECRETARY OF DEFENSE WASHINGTON, D.C. 20301 I 17 April 1984S DE FENSIE SCIENCE BOARD ?M~1RAN"~’ FOR i1Z...mended. Action: JCS, Services, and OSD prepare a JKN3 cur-Ler for Secretary De -fense approval. °’ B. NEW 5000 SERIES DIRECTIVE fRdcdmmmendet tion...requirements, program, acii ecliolv t lc., ron those candidates which possess the prere<isites for suct-e -ces I Joia •, Service acquisitions. The decision to

Automatic nipple detection on 3D images of an automated breast ultrasound system (ABUS)

NASA Astrophysics Data System (ADS)

Javanshir Moghaddam, Mandana; Tan, Tao; Karssemeijer, Nico; Platel, Bram

2014-03-01

Recent studies have demonstrated that applying Automated Breast Ultrasound in addition to mammography in women with dense breasts can lead to additional detection of small, early stage breast cancers which are occult in corresponding mammograms. In this paper, we proposed a fully automatic method for detecting the nipple location in 3D ultrasound breast images acquired from Automated Breast Ultrasound Systems. The nipple location is a valuable landmark to report the position of possible abnormalities in a breast or to guide image registration. To detect the nipple location, all images were normalized. Subsequently, features have been extracted in a multi scale approach and classification experiments were performed using a gentle boost classifier to identify the nipple location. The method was applied on a dataset of 100 patients with 294 different 3D ultrasound views from Siemens and U-systems acquisition systems. Our database is a representative sample of cases obtained in clinical practice by four medical centers. The automatic method could accurately locate the nipple in 90% of AP (Anterior-Posterior) views and in 79% of the other views.

Identification of limiting case between DBA and SBDBA (CL break area sensitivity): A new model for the boron injection system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gonzalez Gonzalez, R.; Petruzzi, A.; D'Auria, F.

2012-07-01

Atucha-2 is a Siemens-designed PHWR reactor under construction in the Republic of Argentina. Its geometrical complexity and (e.g., oblique Control Rods, Positive Void coefficient) required a developed and validated complex three dimensional (3D) neutron kinetics (NK) coupled thermal hydraulic (TH) model. Reactor shut-down is obtained by oblique CRs and, during accidental conditions, by an emergency shut-down system (JDJ) injecting a highly concentrated boron solution (boron clouds) in the moderator tank, the boron clouds reconstruction is obtained using a CFD (CFX) code calculation. A complete LBLOCA calculation implies the application of the RELAP5-3D{sup C} system code. Within the framework of themore » third Agreement 'NA-SA - Univ. of Pisa' a new RELAP5-3D control system for the boron injection system was developed and implemented in the validated coupled RELAP5-3D/NESTLE model of the Atucha 2 NPP. The aim of this activity is to find out the limiting case (maximum break area size) for the Peak Cladding Temperature for LOCAs under fixed boundary conditions. (authors)« less

Charge carrier transport and optical properties of SAM-induced conducting channel in organic semiconductors.

NASA Astrophysics Data System (ADS)

Podzorov, Vitaly

2009-03-01

Certain types of self-assembled monolayers (SAM) grown directly at the surface of organic semiconductors can induce a high surface conductivity in these materials [1]. For example, the conductivity induced by perfluorinated alkyl silanes in organic molecular crystals approaches 10 to -5 Siemens per square. The observed large electronic effect opens new opportunities for nanoscale surface functionalization of organic semiconductors and provides experimental access to the regime of high carrier density. Here, we will discuss temperature variable measurements of SAM-induced conductivity in several types of organic semiconductors. [1]. M. F. Calhoun, J. Sanchez, D. Olaya, M. E. Gershenson and V. Podzorov, ``Electronic functionalization of the surface of organic semiconductors with self-assembled monolayers'', Nature Mat. 7, 84 (2008).

Alternate Multilayer Gratings with Enhanced Diffraction Efficiency in the 500-5000 eV Energy Domain

NASA Astrophysics Data System (ADS)

Polack, François; Lagarde, Bruno; Idir, Mourad; Cloup, Audrey Liard; Jourdain, Erick; Roulliay, Marc; Delmotte, Franck; Gautier, Julien; Ravet-Krill, Marie-Françoise

2007-01-01

An alternate multilayer (AML) grating is a 2 dimensional diffraction structure formed on an optical surface, having a 0.5 duty cycle in the in-plane and in the in-depth direction. It can be made by covering a shallow depth laminar grating with a multilayer stack. We show here that their 2D structure confer AML gratings a high angular and energetic selectivity and therefore enhanced diffraction properties, when used in grazing incidence. In the tender X-ray range (500eV - 5000 eV) they behave much like blazed gratings. Over 15% efficiency has been measured on a 1200 lines/mm Mo/Si AML grating in the 1.2 - 1.5 keV energy range. Computer simulations show that selected multilayer materials such as Cr/C should allow diffraction efficiency over 50% at photon energies over 3 keV.

WE-D-207-01: Background and Clinical Implementation of a Screening Program

DOE Office of Scientific and Technical Information (OSTI.GOV)

Aberle, D.

2015-06-15

In the United States, Lung Cancer is responsible for more cancer deaths than the next four cancers combined. In addition, the 5 year survival rate for lung cancer patients has not improved over the past 40 to 50 years. To combat this deadly disease, in 2002 the National Cancer Institute launched a very large Randomized Control Trial called the National Lung Screening Trial (NLST). This trial would randomize subjects who had substantial risk of lung cancer (due to age and smoking history) into either a Chest X-ray arm or a low dose CT arm. In November 2010, the National Cancermore » Institute announced that the NLST had demonstrated 20% fewer lung cancer deaths among those who were screened with low-dose CT than with chest X-ray. In December 2013, the US Preventive Services Task Force recommended the use of Lung Cancer Screening using low dose CT and a little over a year later (Feb. 2015), CMS announced that Medicare would also cover Lung Cancer Screening using low dose CT. Thus private and public insurers are required to provide Lung Cancer Screening programs using CT to the appropriate population(s). The purpose of this Symposium is to inform medical physicists and prepare them to support the implementation of Lung Screening programs. This Symposium will focus on the clinical aspects of lung cancer screening, requirements of a screening registry for systematically capturing and tracking screening patients and results (such as required Medicare data elements) as well as the role of the medical physicist in screening programs, including the development of low dose CT screening protocols. Learning Objectives: To understand the clinical basis and clinical components of a lung cancer screening program, including eligibility criteria and other requirements. To understand the data collection requirements, workflow, and informatics infrastructure needed to support the tracking and reporting components of a screening program. To understand the role of the medical physicist in implementing Lung Cancer Screening protocols for CT, including utilizing resources such as the AAPM Protocols and the ACR Designated Lung Screening Center program. UCLA Department of Radiology has an Institutional research agreement with Siemens Healthcare; Dr. McNitt-Gray has been a recipient of Research Support from Siemens Healthcare in the past. Dr. Aberle has been a Member of Advisory Boards for the LUNGevity Foundation (2011-present) and Siemens Medical Solutions. (2013)« less

Experimental assessment of out-of-field dose components in high energy electron beams used in external beam radiotherapy.

PubMed

Alabdoaburas, Mohamad M; Mege, Jean-Pierre; Chavaudra, Jean; Bezin, Jérémi Vũ; Veres, Atilla; de Vathaire, Florent; Lefkopoulos, Dimitri; Diallo, Ibrahima

2015-11-08

The purpose of this work was to experimentally investigate the out-of-field dose in a water phantom, with several high energy electron beams used in external beam radiotherapy (RT). The study was carried out for 6, 9, 12, and 18 MeV electron beams, on three different linear accelerators, each equipped with a specific applicator. Measurements were performed in a water phantom, at different depths, for different applicator sizes, and off-axis distances up to 70 cm from beam central axis (CAX). Thermoluminescent powder dosimeters (TLD-700) were used. For given cases, TLD measurements were compared to EBT3 films and parallel-plane ionization chamber measurements. Also, out-of-field doses at 10 cm depth, with and without applicator, were evaluated. With the Siemens applicators, a peak dose appears at about 12-15 cm out of the field edge, at 1 cm depth, for all field sizes and energies. For the Siemens Primus, with a 10 × 10 cm(²) applicator, this peak reaches 2.3%, 1%, 0.9% and 1.3% of the maximum central axis dose (Dmax) for 6, 9, 12 and 18 MeV electron beams, respectively. For the Siemens Oncor, with a 10 × 10 cm(²) applicator, this peak dose reaches 0.8%, 1%, 1.4%, and 1.6% of Dmax for 6, 9, 12, and 14 MeV, respectively, and these values increase with applicator size. For the Varian 2300C/D, the doses at 12.5 cm out of the field edge are 0.3%, 0.6%, 0.5%, and 1.1% of Dmax for 6, 9, 12, and 18 MeV, respectively, and increase with applicator size. No peak dose is evidenced for the Varian applicator for these energies. In summary, the out-of-field dose from electron beams increases with the beam energy and the applicator size, and decreases with the distance from the beam central axis and the depth in water. It also considerably depends on the applicator types. Our results can be of interest for the dose estimations delivered in healthy tissues outside the treatment field for the RT patient, as well as in studies exploring RT long-term effects.

Experimental assessment of out‐of‐field dose components in high energy electron beams used in external beam radiotherapy

PubMed Central

Alabdoaburas, Mohamad M.; Mege, Jean‐Pierre; Chavaudra, Jean; Bezin, Jérémi Vũ; Veres, Attila; de Vathaire, Florent; Lefkopoulos, Dimitri

2015-01-01

The purpose of this work was to experimentally investigate the out‐of‐field dose in a water phantom, with several high energy electron beams used in external beam radiotherapy (RT). The study was carried out for 6, 9, 12, and 18 MeV electron beams, on three different linear accelerators, each equipped with a specific applicator. Measurements were performed in a water phantom, at different depths, for different applicator sizes, and off‐axis distances up to 70 cm from beam central axis (CAX). Thermoluminescent powder dosimeters (TLD‐700) were used. For given cases, TLD measurements were compared to EBT3 films and parallel‐plane ionization chamber measurements. Also, out‐of‐field doses at 10 cm depth, with and without applicator, were evaluated. With the Siemens applicators, a peak dose appears at about 12–15 cm out of the field edge, at 1 cm depth, for all field sizes and energies. For the Siemens Primus, with a 10×10cm2 applicator, this peak reaches 2.3%, 1%, 0.9% and 1.3% of the maximum central axis dose (Dmax) for 6, 9, 12 and 18 MeV electron beams, respectively. For the Siemens Oncor, with a 10×10cm2 applicator, this peak dose reaches 0.8%, 1%, 1.4%, and 1.6% of Dmax for 6, 9, 12, and 14 MeV, respectively, and these values increase with applicator size. For the Varian 2300C/D, the doses at 12.5 cm out of the field edge are 0.3%, 0.6%, 0.5%, and 1.1% of Dmax for 6, 9, 12, and 18 MeV, respectively, and increase with applicator size. No peak dose is evidenced for the Varian applicator for these energies. In summary, the out‐of‐field dose from electron beams increases with the beam energy and the applicator size, and decreases with the distance from the beam central axis and the depth in water. It also considerably depends on the applicator types. Our results can be of interest for the dose estimations delivered in healthy tissues outside the treatment field for the RT patient, as well as in studies exploring RT long‐term effects. PACS number(s): 87.53.Bn, 87.56.bd, 87.56.J‐ PMID:26699572

SU-F-I-49: Vendor-Independent, Model-Based Iterative Reconstruction On a Rotating Grid with Coordinate-Descent Optimization for CT Imaging Investigations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Young, S; Hoffman, J; McNitt-Gray, M

Purpose: Iterative reconstruction methods show promise for improving image quality and lowering the dose in helical CT. We aim to develop a novel model-based reconstruction method that offers potential for dose reduction with reasonable computation speed and storage requirements for vendor-independent reconstruction from clinical data on a normal desktop computer. Methods: In 2012, Xu proposed reconstructing on rotating slices to exploit helical symmetry and reduce the storage requirements for the CT system matrix. Inspired by this concept, we have developed a novel reconstruction method incorporating the stored-system-matrix approach together with iterative coordinate-descent (ICD) optimization. A penalized-least-squares objective function with amore » quadratic penalty term is solved analytically voxel-by-voxel, sequentially iterating along the axial direction first, followed by the transaxial direction. 8 in-plane (transaxial) neighbors are used for the ICD algorithm. The forward problem is modeled via a unique approach that combines the principle of Joseph’s method with trilinear B-spline interpolation to enable accurate reconstruction with low storage requirements. Iterations are accelerated with multi-CPU OpenMP libraries. For preliminary evaluations, we reconstructed (1) a simulated 3D ellipse phantom and (2) an ACR accreditation phantom dataset exported from a clinical scanner (Definition AS, Siemens Healthcare). Image quality was evaluated in the resolution module. Results: Image quality was excellent for the ellipse phantom. For the ACR phantom, image quality was comparable to clinical reconstructions and reconstructions using open-source FreeCT-wFBP software. Also, we did not observe any deleterious impact associated with the utilization of rotating slices. The system matrix storage requirement was only 4.5GB, and reconstruction time was 50 seconds per iteration. Conclusion: Our reconstruction method shows potential for furthering research in low-dose helical CT, in particular as part of our ongoing development of an acquisition/reconstruction pipeline for generating images under a wide range of conditions. Our algorithm will be made available open-source as “FreeCT-ICD”. NIH U01 CA181156; Disclosures (McNitt-Gray): Institutional research agreement, Siemens Healthcare; Past recipient, research grant support, Siemens Healthcare; Consultant, Toshiba America Medical Systems; Consultant, Samsung Electronics.« less

Rate of strontium sorption and the effects of variable aqueous concentrations of sodium and potassium on strontium distribution coefficients of a surficial sediment at the Idaho National Engineering Laboratory, Idaho

USGS Publications Warehouse

Bunde, R.L.; Rosentreter, J.J.; Liszewski, M.J.

1998-01-01

The rate of strontium sorption and the effects of variable aqueous concentrations of sodium and potassium on strontium sorption were measured as part of an investigation to determine strontium chemical transport properties of a surficial sediment at the Idaho National Engineering Laboratory (INEL), Idaho. Batch experimental techniques were used to determine the rate of strontium sorption and strontium distribution coefficients (K(d)s) between aqueous and solid phases. Rate experiments indicate that strontium in solution reached an apparent equilibrium with the sediment in 26 h. K(d)s were derived using the linear isotherm model at initial sodium concentrations from 100 to 5,000 mg/l and initial potassium concentrations from 2 to 150 mg/l. K(d)s ranged from 56 ?? 2 to 62 ?? 3 ml/g at initial aqueous concentrations of sodium and potassium equal to or less than 300 and 150 mg/l, respectively. K(d)s hinged from 4.7 ?? 0.2 to 19 ?? 1 ml/g with initial aqueous concentrations of sodium between 1,000 and 5,000 mg/l. These data indicate that sodium concentrations greater than 300 mg/l in wastewater increase the availability of strontium for transport beneath waste disposal ponds at the INEL by decreasing strontium sorption on the surficial sediment. Wastewater concentrations of sodium and potassium less than 300 and 150 mg/l, respectively, have little effect on the availability of strontium for transport.The rate of strontium sorption and the effects of variable aqueous concentrations of sodium and potassium on strontium sorption were measured as part of an investigation to determine strontium chemical transport properties of a surficial sediment at the Idaho National Engineering Laboratory (INEL), Idaho. Batch experimental techniques were used to determine the rate of strontium sorption and strontium distribution coefficients (Kds) between aqueous and solid phases. Rate experiments indicate that strontium in solution reached an apparent equilibrium with the sediment in 26 h. Kds were derived using the linear isotherm model at initial sodium concentrations from 100 to 5,000 mg/l and initial potassium concentrations from 2 to 150 mg/l. Kds ranged from 56??2 to 62??3 ml/g at initial aqueous concentrations of sodium and potassium equal to or less than 300 and 150 mg/l, respectively. Kds ranged from 4.7??0.2 to 19??1 ml/g with initial aqueous concentrations of sodium between 1,000 and 5,000 mg/l. These data indicate that sodium concentrations greater than 300 mg/l in wastewater increase the availability of strontium for transport beneath waste disposal ponds at the INEL by decreasing strontium sorption on the surficial sediment. Wastewater concentrations of sodium and potassium less than 300 and 150 mg/l, respectively, have little effect on the availability of strontium for transport.

Cornhusker Army Ammunition Plant Remedial Investigation/Feasibility Study; UST and AST Site Investigation.

DTIC Science & Technology

1997-10-01

50000 1000 500000 Chromium CR JS16/SS18 4.05 5000 6.96 50000 Cobalt CO JS16/SS18 1.42 1000 25 50000 Copper CU JS16/SS18 0.965 2500 5 25000 Cyanide...5000 2 10000 Cadmium CD JS13/SS14 0.515 2000 5 5000 Calcium CA JS13/SS14 72 5000 50 5000 Chromium CR JS13/SS14 0.669 5000 22.4 7500 Cobalt CO JS13...ED SS14 21 ! Barium 130 UGL WELL G0053 24-Mar-92 ED SS14 21 Chromium LT 22.4 UGL WELL G0053 ! 24-Mar-92 ED SS14 21 : Cobalt LT ; 10.8 UGL WELL

Microwave Diffraction Techniques from Macroscopic Crystal Models

ERIC Educational Resources Information Center

Murray, William Henry

1974-01-01

Discusses the construction of a diffractometer table and four microwave models which are built of styrofoam balls with implanted metallic reflecting spheres and designed to simulate the structures of carbon (graphite structure), sodium chloride, tin oxide, and palladium oxide. Included are samples of Bragg patterns and computer-analysis results.…

ENVIRONMENTAL TECHNOLOGY VERIFICATION: JOINT (NSF-EPA) VERIFICATION STATEMENT AND REPORT: TRITON SYSTEMS, LLC SOLID BOWL CENTRIFUGE, MODEL TS-5000

EPA Science Inventory

Verification testing of the Triton Systems, LLC Solid Bowl Centrifuge Model TS-5000 (TS-5000) was conducted at the Lake Wheeler Road Field Laboratory Swine Educational Unit in Raleigh, North Carolina. The TS-5000 was 48" in diameter and 30" deep, with a bowl capacity of 16 ft3. ...

Vehicle Electronics and Architecture

DTIC Science & Technology

2011-08-26

NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) Chris Mocnik 5d. PROJECT NUMBER 5e. TASK NUMBER 5f. WORK UNIT NUMBER 7. PERFORMING ORGANIZATION ...NAME(S) AND ADDRESS(ES) US Army RDECOM-TARDEC 6501 E 11 Mile Rd Warren, MI 48397-5000, USA 8. PERFORMING ORGANIZATION REPORT NUMBER 22245 9...processes throughout VEA organization 3.3 Strengthen strategic partnerships, alliances, and technology transfer 4.3 Strengthen strategic

Fiber Optic Feed

DTIC Science & Technology

1990-11-06

Naval Research Laboratory IIK Washington, DC,20375 5000 NRL Memorandum Report 6741 0 N Fiber Optic Feed DENZIL STILWELL, MARK PARENT AND LEw GOLDBERG...SUBTITLE S. FUNDING NUMBERS Fiber Optic Feed 53-0611-A0 6. AUTHOR(S) P. D. Stilwell, M. G. Parent, L. Goldberg 7. PERFORMING ORGANIZATION NAME(S) AND...DISTRIBUTION CODE Approved for public release; distribution unlimited. 13. ABSTRACT (Maximum 200 words) This report details a Fiber Optic Feeding

40 CFR 421.116 - Pretreatment standards for new sources.

Code of Federal Regulations, 2014 CFR

2014-07-01

... pounds) of concentrate digested Lead .174 .081 Zinc .635 .261 Ammonia (as N) 82.910 36.450 Fluoride 21... Lead 2.592 1.203 Zinc 9.442 3.888 Ammonia (as N) 1,233.000 542.5000 Fluoride 324.000 185.100 (c... .069 .032 Zinc .251 .103 Ammonia (as N) 32.790 14.420 Fluoride 8.610 4.920 (d) Subpart K—Precipitation...

40 CFR 421.116 - Pretreatment standards for new sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... pounds) of concentrate digested Lead .174 .081 Zinc .635 .261 Ammonia (as N) 82.910 36.450 Fluoride 21... Lead 2.592 1.203 Zinc 9.442 3.888 Ammonia (as N) 1,233.000 542.5000 Fluoride 324.000 185.100 (c... .069 .032 Zinc .251 .103 Ammonia (as N) 32.790 14.420 Fluoride 8.610 4.920 (d) Subpart K—Precipitation...

40 CFR 421.116 - Pretreatment standards for new sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... pounds) of concentrate digested Lead .174 .081 Zinc .635 .261 Ammonia (as N) 82.910 36.450 Fluoride 21... Lead 2.592 1.203 Zinc 9.442 3.888 Ammonia (as N) 1,233.000 542.5000 Fluoride 324.000 185.100 (c... .069 .032 Zinc .251 .103 Ammonia (as N) 32.790 14.420 Fluoride 8.610 4.920 (d) Subpart K—Precipitation...

40 CFR 421.116 - Pretreatment standards for new sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... pounds) of concentrate digested Lead .174 .081 Zinc .635 .261 Ammonia (as N) 82.910 36.450 Fluoride 21... Lead 2.592 1.203 Zinc 9.442 3.888 Ammonia (as N) 1,233.000 542.5000 Fluoride 324.000 185.100 (c... .069 .032 Zinc .251 .103 Ammonia (as N) 32.790 14.420 Fluoride 8.610 4.920 (d) Subpart K—Precipitation...

40 CFR 421.116 - Pretreatment standards for new sources.

Code of Federal Regulations, 2012 CFR

2012-07-01

... pounds) of concentrate digested Lead .174 .081 Zinc .635 .261 Ammonia (as N) 82.910 36.450 Fluoride 21... Lead 2.592 1.203 Zinc 9.442 3.888 Ammonia (as N) 1,233.000 542.5000 Fluoride 324.000 185.100 (c... .069 .032 Zinc .251 .103 Ammonia (as N) 32.790 14.420 Fluoride 8.610 4.920 (d) Subpart K—Precipitation...

Military Retirement and Wealth Forecasting During DOD Manpower Drawdown

DTIC Science & Technology

2013-09-01

DRAWDOWN 5. FUNDING NUMBERS 6. AUTHOR( S ) Steven D. Mays 7. PERFORMING ORGANIZATION NAME( S ) AND ADDRESS(ES) Naval Postgraduate School Monterey, CA...93943-5000 8. PERFORMING ORGANIZATION REPORT NUMBER 9. SPONSORING /MONITORING AGENCY NAME( S ) AND ADDRESS(ES) N/A 10. SPONSORING/MONITORING...through retirement (McNeil, 2013). The imposed drawdown parameters lessen that likelihood. B. RETIREMENT BEHAVIORS 1. Age Maestas (2009) and

Applications of Should Cost to Achieve Cost Reductions

DTIC Science & Technology

2014-04-01

Operation of the defense acquisition system . Interim DoD Instruction 5000.02. Washington, DC: Office of the Deputy Secretary of Defense. Gutterman...including suggestions for reducing this burden, to Washington Headquarters Services, Directorate for Information Operations and Reports, 1215 Jefferson...FAR) § 15.407-4 that refers primarily to an extensive review of a contractor’s operations to identify and promote more economical and efficient

The 1996 IDA Cost Research Symposium.

DTIC Science & Technology

1996-08-01

5160 Christopher Deegan (703)602-6575 Performer: Naval Surface Warfare Center (211) Carderock Division, NSWC/CD Bethesda, Maryland 20084-5000...Moore (703) 602-0330, ext 208 Cost Engineering Research, Inc. 2011 Crystal Drive Arlington, VA 22202-3717 Bill Hugo Bob Craig Classification...Director, Force and Infrastructure Cost Analysis Division OD (PA&E) Room 2D278, The Pentagon Washington, DC 20301 Dr. Craig College LMI John Wallace

40 CFR 117.3 - Determination of reportable quantities.

Code of Federal Regulations, 2010 CFR

2010-07-01

... fluoride X 1 (0.454) Beryllium nitrate X 1 (0.454) Butyl acetate D 5,000 (2,270) Butylamine C 1,000 (454) n... B 100 (45.4) Cupric acetoarsenite X 1 (0.454) Cupric chloride A 10 (4.54) Cupric nitrate B 100 (45.4... 1,000 (454) Ferric chloride C 1,000 (454) Ferric fluoride B 100 (45.4) Ferric nitrate C 1,000 (454...

40 CFR 117.3 - Determination of reportable quantities.

Code of Federal Regulations, 2011 CFR

2011-07-01

... fluoride X 1 (0.454) Beryllium nitrate X 1 (0.454) Butyl acetate D 5,000 (2,270) Butylamine C 1,000 (454) n... B 100 (45.4) Cupric acetoarsenite X 1 (0.454) Cupric chloride A 10 (4.54) Cupric nitrate B 100 (45.4... 1,000 (454) Ferric chloride C 1,000 (454) Ferric fluoride B 100 (45.4) Ferric nitrate C 1,000 (454...

Research Comparing Charter Schools and Traditional Public Schools. Information Capsule. Volume 1007

ERIC Educational Resources Information Center

Blazer, Christie

2010-01-01

During the 2008-09 school year, over 5,000 charter schools operated in 40 states and Washington, D.C. and were attended by over 1.5 million students, or about three percent of the nation's public school students. Although the first U.S. charter schools opened in 1992, debate continues over whether they provide students with a better education than…

78 FR 72682 - Proposed Collection; 60-Day Comment Request; Rapid Throughput Standardized Evaluation of...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-12-03

... of 14-17 year-old students: Consent Form. 5,000 1 1/60 83 14-18 year-old students: School Survey (TLI.... The TLI is designed to identify the propensity for these and other substance abuse prior to... youths: Twins Survey (Demo/D&A).. 1 10/60 100 14-18 year-old youths: Twins Survey 1 10/60 100...

In vitro assessment of 3 dentifrices containing fluoride in preventing demineralization of overdenture abutments and root surfaces.

PubMed

Goettsche, Zachary S; Ettinger, Ronald L; Wefel, James S; Hogan, Mary M; Harless, Jeffery D; Qian, Fang

2014-11-01

Caries development under overdentures has been a continuing problem and requires the daily use of fluoride to prevent demineralization. The purpose of this in vitro study was to compare the effectiveness of dentifrices containing tricalcium phosphate or calcium phosphosilicate in combination with fluoride to prevent the demineralization of overdenture abutments and root surfaces. A total of 56 caries-free extracted teeth were prepared as overdenture abutments. The teeth were painted with acid-resistant varnish, leaving one 1×4-mm window on occlusal and root surfaces. The teeth were randomly divided into 4 groups: a control group treated with distilled/deionized water only, a group treated with ClinPro 5000, a group treated with ReNew, and a group treated with Prevident 5000 gel. Each tooth was subjected to a demineralizing/remineralizing cycling protocol for 12 days with the appropriate treatment products. The teeth were sectioned longitudinally through both windows. Photomicrographs were made of 3 representative sections from each tooth. A representative section was defined as one that included both windows and was cut from the part of the tooth that had the flattest surface to reduce the edge effect. The depths of the lesions were measured on representative sections from each group. A 1-way MANOVA and a 1-way ANOVA with the post hoc Tukey-Kramer test were used to evaluate the treatment effects on the criterion variables (α=.05). The total lesion depths of the control teeth on the occlusal surface were not statistically significantly deeper than for the 3 dentifrices (P=.7705). However, all 3 dentifrices had narrower cavitation depths than the control (mean cavitation band depth, 43.59 [ReNew] versus 37.99 [Prevident 5000 gel] versus 36.70 [ClinPro 5000] versus 246.86 [control]) (P<.001). The mean remineralization band depth for ClinPro 5000 was significantly greater than for the other 2 treatment groups (118.03 [ClinPro 5000] versus 107.80 [ReNew] versus 102.28 [Prevident 5000 gel]) (P<.001). On root surfaces, the total lesion depth for the control group was statistically significantly deeper than for the 3 dentifrices (mean total lesion depth, 150.31 [control] versus 82.05 [ReNew] versus 68.10 [ClinPro 5000] versus 56.97 [Prevident 5000 gel]) (P<.001). The data indicated that teeth treated with Prevident 5000 gel had the shallowest total lesion depth and were statistically significantly different from those treated with ReNew and ClinPro 5000. Moreover, teeth treated with ReNew were found to have the largest remineralization band depth, which was statistically significantly different compared with ClinPro 5000 and Prevident 5000 gel (mean remineralization band depth, 49.66 [ReNew] versus 36.14 [ClinPro 5000] versus 23.27 [Prevident 5000 gel]) (P<.001), but no difference was found in cavitation depth of the root lesions between the 3 dentifrices. The addition of tricalcium phosphate or calcium phosphosilicate to fluoride-containing dentifrices (5000 ppm) does not significantly improve their ability to prevent demineralization of the cut dentin surface of overdenture abutments. However, on root surfaces, ReNew, which contains calcium phosphosilicate, was found to improve remineralization of the lesions compared with Prevident 5000 gel or ClinPro 5000. Copyright © 2014 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

A facile approach for the fabrication of 3D flower-like Cu2S nanostructures on brass mesh with temperature-induced wetting transition for efficient oil-water separation

NASA Astrophysics Data System (ADS)

Niu, Lei; Kang, Zhixin

2017-11-01

3D flower-like Cu2S nanostructures on brass meshes have been fabricated for the first time, with a reversible wetting transition and excellent durability. In the present work, we demonstrated a simple and environmentally-benign method to fabricate the nanostructures utilizing an electrolyte containing CuSO4·5H2O, EDTA-2Na and CH3CSNH2. The superhydrophobicity was achieved by drying thoroughly at 200 °C, instead of using low surface energy materials. After annealing at 300 °C for 6 min, the superhydrophobic surface was oxidized and became superhydrophilic. However, the superhydrophobicity can be restored by heating at 200 °C for several hours. In simpler terms, the reversible wetting transition is responded to the temperature. Scanning electron microscopy, X-ray diffractometer, energy-dispersive X-ray spectroscopy, and X-ray photoelectron spectroscopy were employed to characterize the surfaces and analyze the wetting transition mechanism. Furthermore, different kinds of oily sewages were separated by as-prepared mesh with high separation efficiency. It is believed that this method should have a promising future in expanding the applications of copper alloys.

Thermal vacancies and phase separation in bcc mixtures of helium-3 and helium-4

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fraass, Benedick Andrew

1980-01-01

Thermal vacancy concentrations in crystals of 3He- 4He mixtures have been determined. A new x-ray diffractometer-position sensitive detector system is used to make measurements of the absolute lattice parameter of the helium crystals with an accuracy of 300 ppM, and measurements of changes in lattice parameters to better than 60 ppM. The phase separation of the concentrated 3He- 4He mixtures has been studied in detail with the x-ray measurements. Vacancy concentrations in crystals with 99%, 51%, 28%, 12%, and 0% 3He have been determined. Phase separation has been studied in mixed crystals with concentrations of 51%, 28%, and 12% 3Hemore » and melting pressures between 3.0 and 6.1 MPa. The phase separation temperatures determined in this work are in general agreement with previous work. The pressure dependence of T c, the phase separation temperature for a 50% mixture, is found to be linear: dT c/dP = -34 mdeg/MPa. The x-ray measurements are used to make several comments on the low temperature phase diagram of the helium mixtures.« less

Effect of Cerium Oxide on Morphologies and Electrochemical Properties of Ni-W-P Coating on AZ91D Magnesium

NASA Astrophysics Data System (ADS)

Sun, Wan-chang; Xu, Jia-Min; Wang, Yuan; Guo, Fang; Jia, Zong-Wei

2017-12-01

AZ91D magnesium alloy substrate was first pretreated in a phosphoric acid to obtain a phosphate coating, and then, the electroless ternary Ni-W-P coating was deposited using a sulfate nickel bath. The morphologies of the Ni-W-P coating were observed by using scanning electron microscope, the deposition rate of the coating was examined with the method of gravimetric analysis, and the phase analysis was identified by x-ray diffractometer. Electrochemical property was tested by means of an electrochemical analyzer. The results indicated that the addition of an optimum concentration of CeO2 (cerium oxide) particles could evidently improve the deposition rate and the stability of the plating bath. However, it acted as an inhibiting effect as the concentration of CeO2 particles exceeded to 8 mg/L in the sulfate nickel bath. The results also revealed that the morphology of Ni-W-P coating became more smooth, compact and uniform with the increase in the concentrations of CeO2 particles in the bath, but the corrosion resistance decreased due to the precipitation of crystal phases (Ni3P, Ni4W, etc.) after heat treatment.

3D CFD Quantification of the Performance of a Multi-Megawatt Wind Turbine

NASA Astrophysics Data System (ADS)

Laursen, J.; Enevoldsen, P.; Hjort, S.

2007-07-01

This paper presents the results of 3D CFD rotor computations of a Siemens SWT-2.3-93 variable speed wind turbine with 45m blades. In the paper CFD is applied to a rotor at stationary wind conditions without wind shear, using the commercial multi-purpose CFD-solvers ANSYS CFX 10.0 and 11.0. When comparing modelled mechanical effects with findings from other models and measurements, good agreement is obtained. Similarly the computed force distributions compare very well, whereas some discrepancies are found when comparing with an in-house BEM model. By applying the reduced axial velocity method the local angle of attack has been derived from the CFD solutions, and from this knowledge and the computed force distributions, local airfoil profile coefficients have been computed and compared to BEM airfoil coefficients. Finally, the transition model of Langtry and Menter is tested on the rotor, and the results are compared with the results from the fully turbulent setup.

Aerodynamic Design of a Four-Stage Low-Speed Axial Compressor for Cantilevered Stator Research

NASA Astrophysics Data System (ADS)

Wallace, James N.

This research is focused on the baseline aerodynamic design of a four-stage low-speed axial compressor with the intent to achieve similarity of cantilevered stator hub leakage flows with those in the rear stages of Siemens large gas turbine compressors. The baseline airfoil design is to act as a comparison for all future research completed in the low speed compressor and, therefore, will not include possible future research topics such as 3-D airfoil geometry or end-wall contouring. Following the design of the airfoils is the aerodynamic design of the facility including the inlet and exhaust. These components were designed to eliminate interactions of the compressor with the facility and to accommodate instrumentation. A baseline set of aerodynamic instrumentation is then suggested to characterize compressor performance. Fully 3-D steady CFD was used extensively during the design of both the facility and the compressor, as well as determining the locations and types of instrumentation.

CJ-1639: A Potent and Highly Selective Dopamine D3 Receptor Full Agonist.

PubMed

Chen, Jianyong; Collins, Gregory T; Levant, Beth; Woods, James; Deschamps, Jeffrey R; Wang, Shaomeng

2011-08-11

We have identified several ligands with high binding affinities to the dopamine D3 receptor and excellent selectivity over the D2 and D1 receptors. CJ-1639 (17) binds to the D3 receptor with a K(i) value of 0.50 nM and displays a selectivity of >5,000 times over D2 and D1 receptors in binding assays using dopamine receptors expressed in the native rat brain tissues. CJ-1639 binds to human D3 receptor with a K(i) value of 3.61 nM and displays over >1000-fold selectivity over human D1 and D2 receptors. CJ-1639 is active at 0.01 mg/kg at the dopamine D3 receptor in the rat and only starts to show a modest D2 activity at doses as high as 10 mg/kg. CJ-1639 is the most potent and selective D3 full agonist reported to date.

17 CFR 150.2 - Position limits.

Code of Federal Regulations, 2010 CFR

2010-04-01

... Oats 600 1,400 2,000 Soybeans and Mini-Soybeans 1 600 6,500 10,000 Wheat and Mini-Wheat 1 600 5,000 6... Spring Wheat 600 5,000 6,500 New York Board of Trade Cotton No. 2 300 3,500 5,000 Kansas City Board of Trade Hard Winter Wheat 600 5,000 6,500 1 For purposes of compliance with these limits, positions in the...

Morphometric analysis - Cone beam computed tomography to predict bone quality and quantity.

PubMed

Hohlweg-Majert, B; Metzger, M C; Kummer, T; Schulze, D

2011-07-01

Modified quantitative computed tomography is a method used to predict bone quality and quantify the bone mass of the jaw. The aim of this study was to determine whether bone quantity or quality was detected by cone beam computed tomography (CBCT) combined with image analysis. MATERIALS AND PROCEDURES: Different measurements recorded on two phantoms (Siemens phantom, Comac phantom) were evaluated on images taken with the Somatom VolumeZoom (Siemens Medical Solutions, Erlangen, Germany) and the NewTom 9000 (NIM s.r.l., Verona, Italy) in order to calculate a calibration curve. The spatial relationships of six sample cylinders and the repositioning from four pig skull halves relative to adjacent defined anatomical structures were assessed by means of three-dimensional visualization software. The calibration curves for computer tomography (CT) and cone beam computer tomography (CBCT) using the Siemens phantom showed linear correlation in both modalities between the Hounsfield Units (HU) and bone morphology. A correction factor for CBCT was calculated. Exact information about the micromorphology of the bone cylinders was only available using of micro computer tomography. Cone-beam computer tomography is a suitable choice for analysing bone mass, but, it does not give any information about bone quality. 2010 European Association for Cranio-Maxillo-Facial Surgery. Published by Elsevier Ltd. All rights reserved.

Measurement and control system for cryogenic helium gas bearing turbo-expander experimental platform based on Siemens PLC S7-300

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, J.; Xiong, L. Y.; Peng, N.

2014-01-29

An experimental platform for cryogenic Helium gas bearing turbo-expanders is established at the Technical Institute of Physics and Chemistry, Chinese Academy of Sciences. This turbo-expander experimental platform is designed for performance testing and experimental research on Helium turbo-expanders with different sizes from the liquid hydrogen temperature to the room temperature region. A measurement and control system based on Siemens PLC S7-300 for this turbo-expander experimental platform is developed. Proper sensors are selected to measure such parameters as temperature, pressure, rotation speed and air flow rate. All the collected data to be processed are transformed and transmitted to S7-300 CPU. Siemensmore » S7-300 series PLC CPU315-2PN/DP is as master station and two sets of ET200M DP remote expand I/O is as slave station. Profibus-DP field communication is established between master station and slave stations. The upper computer Human Machine Interface (HMI) is compiled using Siemens configuration software WinCC V6.2. The upper computer communicates with PLC by means of industrial Ethernet. Centralized monitoring and distributed control is achieved. Experimental results show that this measurement and control system has fulfilled the test requirement for the turbo-expander experimental platform.« less

Pooled nucleic acid testing increases the diagnostic yield of acute HIV infections in a high-risk population compared to 3rd and 4th generation HIV enzyme immunoassays.

PubMed

Krajden, Mel; Cook, Darrel; Mak, Annie; Chu, Ken; Chahil, Navdeep; Steinberg, Malcolm; Rekart, Michael; Gilbert, Mark

2014-09-01

We compared a 3rd generation (gen) and two 4th gen HIV enzyme immunoassays (EIA) to pooled nucleic acid testing (PNAT) for the identification of pre- and early seroconversion acute HIV infection (AHI). 9550 specimens from males >18 year from clinics attended by men who have sex with men were tested by Siemens ADVIA Centaur(®) HIV 1/O/2 (3rd gen) and HIV Combo (4th gen), as well as by Abbott ARCHITECT(®) HIV Ag/Ab Combo (4th gen). Third gen non-reactive specimens were also tested by Roche COBAS(®) Ampliprep/COBAS® TaqMan HIV-1 Test v.2 in pools of 24 samples. Sensitivity and specificity of the three EIAs for AHI detection were compared. 7348 persons contributed 9435 specimens and had no evidence of HIV infection, 79 (94 specimens) had established HIV infection, 6 (9 specimens) had pre-seroconversion AHI and 9 (12 specimens) had early seroconversion AHI. Pre-seroconversion AHI cases were not detected by 3rd gen EIA, whereas 2/6 (33.3%) were detected by Siemens 4th gen, 4/6 (66.7%) by Abbott 4th gen and 6/6 (100%) by PNAT. All three EIAs and PNAT detected all individuals with early seroconversion AHI. Overall sensitivity/specificity for the EIAs relative to WB or NAT resolved infection status was 93.6%/99.9% for Siemens 3rd gen, 95.7%/99.7% for Siemens 4th gen and 97.9%/99.2% for Abbott 4th gen. While both 4th gen EIAs demonstrated improved sensitivity for AHI compared to 3rd gen EIA, PNAT identified more AHI cases than either 4th gen assay. PNAT is likely to remain a useful strategy to identify AHI in high-risk populations. Copyright © 2014 Elsevier B.V. All rights reserved.

Cadmium sulfide anchored in three-dimensional graphite cage for high performance supercapacitors

NASA Astrophysics Data System (ADS)

Chen, Liang; Zuo, Yinze; Zhang, Yu; Gao, Yanmin

2018-05-01

Cadmium sulfide (CdS) nanoparticles were anchored in a three-dimensional (3D) graphite cage for high performance supercapacitors. Significantly, the graphite cage intensified the construction of electroactive materials and facilitated the transfer of ions. As a result, the 3D-CdS/graphite cage revealed a great thermal stability and high specific capacitance (511 F/g at 5 A/g). Additionally, the 3D-CdS/graphite//reduced graphene oxide (rGO) asymmetric supercapacitor revealed a high energy density (30.4 Wh/kg at a power density of 800 W/kg) and long-term cycling stability (90.1% retention after 5000 cycles at 10 A/g) for practical applications.

VizieR Online Data Catalog: 3D correction in 5 photometric systems (Bonifacio+, 2018)

NASA Astrophysics Data System (ADS)

Bonifacio, P.; Caffau, E.; Ludwig, H.-G.; Steffen, M.; Castelli, F.; Gallagher, A. J.; Kucinskas, A.; Prakapavicius, D.; Cayrel, R.; Freytag, B.; Plez, B.; Homeier, D.

2018-01-01

We have used the CIFIST grid of CO5BOLD models to investigate the effects of granulation on fluxes and colours of stars of spectral type F, G, and K. We publish tables with 3D corrections that can be applied to colours computed from any 1D model atmosphere. For Teff>=5000K, the corrections are smooth enough, as a function of atmospheric parameters, that it is possible to interpolate the corrections between grid points; thus the coarseness of the CIFIST grid should not be a major limitation. However at the cool end there are still far too few models to allow a reliable interpolation. (20 data files).

Experiment to Determine the Absorption Coefficient of Gamma Rays as a Function of Energy.

ERIC Educational Resources Information Center

Ouseph, P. J.; And Others

1982-01-01

Simpler than x-ray diffractometer experiments, the experiment described illustrates certain concepts regarding the interaction of electromagnetic rays with matter such as the exponential decrease in the intensity with absorber thickness, variation of the coefficient of absorption with energy, and the effect of the K-absorption edge on the…

In situ surface/interface x-ray diffractometer for oxide molecular beam epitaxy

NASA Astrophysics Data System (ADS)

Lee, J. H.; Tung, I. C.; Chang, S.-H.; Bhattacharya, A.; Fong, D. D.; Freeland, J. W.; Hong, Hawoong

2016-01-01

In situ studies of oxide molecular beam epitaxy by synchrotron x-ray scattering has been made possible by upgrading an existing UHV/molecular beam epitaxy (MBE) six-circle diffractometer system. For oxide MBE growth, pure ozone delivery to the chamber has been made available, and several new deposition sources have been made available on a new 12 in. CF (ConFlat, a registered trademark of Varian, Inc.) flange. X-ray diffraction has been used as a major probe for film growth and structures for the system. In the original design, electron diffraction was intended for the secondary diagnostics available without the necessity of the x-ray and located at separate positions. Deposition of films was made possible at the two diagnostic positions. And, the aiming of the evaporation sources is fixed to the point between two locations. Ozone can be supplied through two separate nozzles for each location. Also two separate thickness monitors are installed. Additional features of the equipment are also presented together with the data taken during typical oxide film growth to illustrate the depth of information available via in situ x-ray techniques.

In situ surface/interface x-ray diffractometer for oxide molecular beam epitaxy.

PubMed

Lee, J H; Tung, I C; Chang, S-H; Bhattacharya, A; Fong, D D; Freeland, J W; Hong, Hawoong

2016-01-01

In situ studies of oxide molecular beam epitaxy by synchrotron x-ray scattering has been made possible by upgrading an existing UHV/molecular beam epitaxy (MBE) six-circle diffractometer system. For oxide MBE growth, pure ozone delivery to the chamber has been made available, and several new deposition sources have been made available on a new 12 in. CF (ConFlat, a registered trademark of Varian, Inc.) flange. X-ray diffraction has been used as a major probe for film growth and structures for the system. In the original design, electron diffraction was intended for the secondary diagnostics available without the necessity of the x-ray and located at separate positions. Deposition of films was made possible at the two diagnostic positions. And, the aiming of the evaporation sources is fixed to the point between two locations. Ozone can be supplied through two separate nozzles for each location. Also two separate thickness monitors are installed. Additional features of the equipment are also presented together with the data taken during typical oxide film growth to illustrate the depth of information available via in situ x-ray techniques.

High-resolution neutron powder diffractometer SPODI at research reactor FRM II

NASA Astrophysics Data System (ADS)

Hoelzel, M.; Senyshyn, A.; Juenke, N.; Boysen, H.; Schmahl, W.; Fuess, H.

2012-03-01

SPODI is a high-resolution thermal neutron diffractometer at the research reactor Heinz Maier-Leibnitz (FRM II) especially dedicated to structural studies of complex systems. Unique features like a very large monochromator take-off angle of 155° and a 5 m monochromator-sample distance in its standard configuration achieve both high-resolution and a good profile shape for a broad scattering angle range. Two dimensional data are collected by an array of 80 vertical position sensitive 3He detectors. SPODI is well suited for studies of complex structural and magnetic order and disorder phenomena at non-ambient conditions. In addition to standard sample environment facilities (cryostats, furnaces, magnet) specific devices (rotatable load frame, cell for electric fields, multichannel potentiostat) were developed. Thus the characterisation of functional materials at in-operando conditions can be achieved. In this contribution the details of the design and present performance of the instrument are reported along with its specifications. A new concept for data reduction using a 2 θ dependent variable height for the intensity integration along the Debye-Scherrer lines is introduced.

A preliminary neutron crystallographic study of thaumatin

DOE Office of Scientific and Technical Information (OSTI.GOV)

Teixeira, Susana C. M.; Institut Laue Langevin, 6 Rue Jules Horowitz, 38042 Grenoble; EPSAM and ISTM, Keele University, Staffordshire ST5 5BG

2008-05-01

Preliminary neutron crystallographic data from the sweet protein thaumatin have been recorded using the LADI-III diffractometer at the Institut Laue Langevin (ILL). The results illustrate the feasibility of a full neutron structural analysis aimed at further understanding the molecular basis of the perception of sweet taste. Such an analysis will exploit the use of perdeuterated thaumatin. A preliminary neutron crystallographic study of the sweet protein thaumatin is presented. Large hydrogenated crystals were prepared in deuterated crystallization buffer using the gel-acupuncture method. Data were collected to a resolution of 2 Å on the LADI-III diffractometer at the Institut Laue Langevin (ILL).more » The results demonstrate the feasibility of a full neutron crystallographic analysis of this structure aimed at providing relevant information on the location of H atoms, the distribution of charge on the protein surface and localized water in the structure. This information will be of interest for understanding the specificity of thaumatin–receptor interactions and will contribute to further understanding of the molecular mechanisms underlying the perception of taste.« less

Precession technique and electron diffractometry as new tools for crystal structure analysis and chemical bonding determination.

PubMed

Avilov, A; Kuligin, K; Nicolopoulos, S; Nickolskiy, M; Boulahya, K; Portillo, J; Lepeshov, G; Sobolev, B; Collette, J P; Martin, N; Robins, A C; Fischione, P

2007-01-01

We have developed a new fast electron diffractometer working with high dynamic range and linearity for crystal structure determinations. Electron diffraction (ED) patterns can be scanned serially in front of a Faraday cage detector; the total measurement time for several hundred ED reflections can be tens of seconds having high statistical accuracy for all measured intensities (1-2%). This new tool can be installed to any type of TEM without any column modification and is linked to a specially developed electron beam precession "Spinning Star" system. Precession of the electron beam (Vincent-Midgley technique) reduces dynamical effects allowing also use of accurate intensities for crystal structure analysis. We describe the technical characteristics of this new tool together with the first experimental results. Accurate measurement of electron diffraction intensities by electron diffractometer opens new possibilities not only for revealing unknown structures, but also for electrostatic potential determination and chemical bonding investigation. As an example, we present detailed atomic bonding information of CaF(2) as revealed for the first time by precise electron diffractometry.

Investigation of the response of a neutron-Hand monitor dedicated to the powder diffractometer at CENM-Maamora

DOE Office of Scientific and Technical Information (OSTI.GOV)

Messous, M.Y.; Belhorma, B.; Labrim, H.

2015-07-01

Neutrons are used for the study of condensed matter. A neutron beam can indeed easily penetrate the solid material and undergo diffraction phenomena. Analysis of the diffused neutrons allows studying the atomic structure of crossed material. Their neutral electric charge makes them nondestructive probe of a great interest. In general, the size of the powder samples is very small and therefore the centering of the beam on these is very crucial. It is in this context we proceed to test a portable neutron monitor for centering and checking beam leak around the shielding to be installed around the diffractometer inmore » TRIGA Mark II of CENM. It's consisting of a scintillation neutron detector NE426 ({sup 6}LiF + ZnS (Ag)) with electronic module and data acquisition system. The effect of radiation from radioactive neutrons source {sup 252}Cf is shown. Sensitivity and differential linearity are also performed. This study indicates several advantages of this detector with very good detection sensitivity and excellent stability during the counting time. (authors)« less

Highly potent artemisinin-derived dimers and trimers: Synthesis and evaluation of their antimalarial, antileukemia and antiviral activities.

PubMed

Reiter, Christoph; Fröhlich, Tony; Gruber, Lisa; Hutterer, Corina; Marschall, Manfred; Voigtländer, Cornelia; Friedrich, Oliver; Kappes, Barbara; Efferth, Thomas; Tsogoeva, Svetlana B

2015-09-01

New pharmaceutically active compounds can be obtained by modification of existing drugs to access more effective agents in the wake of drug resistance amongst others. To achieve this goal the concept of hybridization was established during the last decade. We employed this concept by coupling two artemisinin-derived precursors to obtain dimers or trimers with increased in vitro activity against Plasmodiumfalciparum 3D7 strain, leukemia cells (CCRF-CEM and multidrug-resistant subline CEM/ADR5000) and human cytomegalovirus (HCMV). Dimer 4 (IC50 of 2.6 nM) possess superior antimalarial activity compared with its parent compound artesunic acid(3) (IC50 of 9.0 nM). Dimer5 and trimers6 and 7 display superior potency against both leukemia cell lines (IC50 up to 0.002 μM for CCRF-CEM and IC50 up to 0.20 μM for CEM/ADR5000) and are even more active than clinically used doxorubicin (IC50 1.61 μM for CEM/ADR5000). With respect to anti-HCMV activity, trimer6 is the most efficient hybrid (IC50 0.04 μM) outperforming ganciclovir (IC50 2.6 μM), dihydroartemisinin(IC50 >10 μM) and artesunic acid (IC50 3.8 μM). Copyright © 2015 Elsevier Ltd. All rights reserved.

Quantitative comparison of the application accuracy between NDI and IGT tracking systems

NASA Astrophysics Data System (ADS)

Li, Qinghang; Zamorano, Lucia J.; Jiang, Charlie Z. W.; Gong, JianXing; Diaz, Fernando

1999-07-01

The application accuracy is a crucial factor for the stereotactic surgical localization system in which space digitization system is one of the most important part of equipment. In this study we compared the application accuracy of using the OPTOTRAK space digitization system (OPTOTRAK 3020, Northern Digital, Waterloo, CAN) and FlashPoint Model 3000 and 5000 3-D digitizer systems (FlashPoint Model 3000 and 5000, Image Guided Surgery Technology Inc., Boulder, CO 80301, USA) for interactive localization of intracranial lesions. A phantom was mounted with the implantable frameless marker system (Fischer- Leibinger, Freiburg, Germany) which randomly distributed markers on the surface of the phantom. The target point was digitized and the coordinates were recorded and compared with reference points. The differences from the reference points were used as the deviation from the `true point'. The mean square root was calculated to show the sum of vectors. A paired t-test was used to analyze results. The results of the phantom showed that the mean square roots were 0.76 +/- 0.54 mm for the OPTOTRAK system and 1.23 +/- 0.53 mm for FlashPoint Model 3000 3-D digitizer system and 1.00 +/- 0.42 mm for FlashPoint Model 3000 3-D digitizer system in the 1 mm sections of CT scan. This preliminary results showed that there is no significant difference between two tracking systems. Both of them can be used for image guided surgery procedure.

Investigation of the scatter contribution in single photon transmission measurements by means of Monte Carlo simulations

NASA Astrophysics Data System (ADS)

Wegmann, K.; Adam, L.-E.; Livieratos, L.; Zaers, J.; Bailey, D. L.; Brix, G.

1999-08-01

The fraction of detected scattered radiation in transmission measurements with a single photon transmission (SPT) source of Cesium-137 was investigated by means of Monte Carlo (MC) techniques. The scatter contamination was determined for different energy thresholds and the use of interplane septa. The simulations were validated with measurements performed at the whole-body 3D PET scanner ECAT EXACT 3D (CTI/Siemens, Knoxville, TN), which uses a SPT source. The comparison of the results from the simulations and the measurements shows good agreement. Transmission through a water-filled cylinder (o=20 cm) gave values of the scatter fraction SF of about 27% at a lower level discriminator (LLD) value of 500 keV in the center of the projection. A reduction to 17% was achieved by an increase of the LLD to 600 keV; a relative decrease of 37%. But a corresponding loss of counts by a factor of 1.5 was observed. Furthermore, simulations of the ECAT EXACT HR/sup +/ have been performed, a whale-body PET scanner which can be operated in 2D and 3D mode, but has no SPT mode yet. At a value of the LLD of 500 keV, the simulations showed a decrease of the SF in the 2D mode of 45% relative to the 3D mode for the transmission of the water-filled cylinder.

Characterization and optimization of image quality as a function of reconstruction algorithms and parameter settings in a Siemens Inveon small-animal PET scanner using the NEMA NU 4-2008 standards

NASA Astrophysics Data System (ADS)

Visser, Eric P.; Disselhorst, Jonathan A.; van Lier, Monique G. J. T. B.; Laverman, Peter; de Jong, Gabie M.; Oyen, Wim J. G.; Boerman, Otto C.

2011-02-01

The image reconstruction algorithms provided with the Siemens Inveon small-animal PET scanner are filtered backprojection (FBP), 3-dimensional reprojection (3DRP), ordered subset expectation maximization in 2 or 3 dimensions (OSEM2D/3D) and maximum a posteriori (MAP) reconstruction. This study aimed at optimizing the reconstruction parameter settings with regard to image quality (IQ) as defined by the NEMA NU 4-2008 standards. The NEMA NU 4-2008 image quality phantom was used to determine image noise, expressed as percentage standard deviation in the uniform phantom region (%STD unif), activity recovery coefficients for the FDG-filled rods (RC rod), and spill-over ratios for the non-radioactive water- and air-filled phantom compartments (SOR wat and SOR air). Although not required by NEMA NU 4, we also determined a contrast-to-noise ratio for each rod (CNR rod), expressing the trade-off between activity recovery and image noise. For FBP and 3DRP the cut-off frequency of the applied filters, and for OSEM2D and OSEM3D, the number of iterations was varied. For MAP, the "smoothing parameter" β and the type of uniformity constraint (variance or resolution) were varied. Results of these analyses were demonstrated in images of an FDG-injected rat showing tumours in the liver, and of a mouse injected with an 18F-labeled peptide, showing a small subcutaneous tumour and the cortex structure of the kidneys. Optimum IQ in terms of CNR rod for the small-diameter rods was obtained using MAP with uniform variance and β=0.4. This setting led to RC rod,1 mm=0.21, RC rod,2 mm=0.57, %STD unif=1.38, SOR wat=0.0011, and SOR air=0.00086. However, the highest activity recovery for the smallest rods with still very small %STD unif was obtained using β=0.075, for which these IQ parameters were 0.31, 0.74, 2.67, 0.0041, and 0.0030, respectively. The different settings of reconstruction parameters were clearly reflected in the rat and mouse images as the trade-off between the recovery of small structures (blood vessels, small tumours, kidney cortex structure) and image noise in homogeneous body parts (healthy liver background). Highest IQ for the Inveon PET scanner was obtained using MAP reconstruction with uniform variance. The setting of β depended on the specific imaging goals.

Utilization of the High Flux Isotope Reactor at Oak Ridge National Laboratory

DOE Office of Scientific and Technical Information (OSTI.GOV)

Selby, Douglas L; Bilheux, Hassina Z; Meilleur, Flora

2015-01-01

This paper addresses several aspects of the scientific utilization of the Oak Ridge National Laboratory High Flux Isotope Reactor (HFIR). Topics to be covered will include: 1) HFIR neutron scattering instruments and the formal instrument user program; 2) Recent upgrades to the neutron scattering instrument stations at the reactor, and 3) eMod a new tool for addressing instrument modifications and providing configuration control and design process for scientific instruments at HFIR and the Spallation Neutron Source (SNS). There are 15 operating neutron instrument stations at HFIR with 12 of them organized into a formal user program. Since the last presentationmore » on HFIR instruments at IGORR we have installed a Single Crystal Quasi-Laue Diffractometer instrument called IMAGINE; and we have made significant upgrades to HFIR neutron scattering instruments including the Cold Triple Axis Instrument, the Wide Angle Neutron Diffractometer, the Powder Diffractometer, and the Neutron Imaging station. In addition, we have initiated upgrades to the Thermal Triple Axis Instrument and the Bio-SANS cold neutron instrument detector system. All of these upgrades are tied to a continuous effort to maintain a high level neutron scattering user program at the HFIR. For the purpose of tracking modifications such as those mentioned and configuration control we have been developing an electronic system for entering instrument modification requests that follows a modification or instrument project through concept development, design, fabrication, installation, and commissioning. This system, which we call eMod, electronically leads the task leader through a series of questions and checklists that then identifies such things as ES&H and radiological issues and then automatically designates specific individuals for the activity review process. The system has been in use for less than a year and we are still working out some of the inefficiencies, but we believe that this will become a very effective tool for achieving the configuration and process control believed to be necessary for scientific instrument systems.« less

The Double R Theory of Language Comprehension

DTIC Science & Technology

2004-02-01

AFRL-HE-AZ-TR- 2003 - 0110 Approved for public release; distribution is unlimited. AIR FORCE MATERIEL COMMAND AIR FORCE RESEARCH LABORATORY Human...REPORT TYPE Final 3. DATES COVERED (From - To) March 2003 to February 2004 5a. CONTRACT NUMBER F41624-97-D-5000 5b. GRANT NUMBER 4. TITLE...Laboratory Human Effectiveness Directorate Warfighter Training Research Division 6030 South Kent Street Mesa AZ 85212-6061 AFRL-HE-AZ-TR- 2003

Seventh Colloquium on High Resolution Molecular Spectroscopy 14 to 18 September 1981 (Septieme Colloque sur la Spectroscopie Moleculaire a Haute Resolution 14 a 18 Septembre 1981).

DTIC Science & Technology

1981-01-01

K61n, D-5000 K61n 41 In our attempt to observe the high resolution infra- red spectra of the astrophysically interesting cyanopolyyne molecules, we...cyclobutylsilane could exist in two possible con- formations with the silylgroup in either the axial or equatorial position with respect to the puckered

Sentence Comprehension: A Parallel Distributed Processing Approach

DTIC Science & Technology

1989-07-14

NAME OF PERFORMING ORGANIZATION 6b OFFICE SYMBOL 7a NAME OF MONITORING ORGANIZATION (If aodkawe) Computer Sciences DivisionCarnegie-Mellon University...Pittsburgh, Pennsylvania 15213. Arlington, Virginia 22217-5000 $a. NAME OF FUNOINGISPONSORING Sb OFFICE SYMBOL 9 PROCUREMENT INSTRUMENT IOENTIFICATION...3 OTIC USERS 22a NAME OF RESPONSIBLE INOIVI0UAL 22b TELEPHONE (include Area COd) 22c. OFFICE SYMBOL Dr. Alan L. Meyrowitz (202) 696-4302 N00014 D0

An Approach to the Management of Hazardous Materials.

DTIC Science & Technology

1981-09-01

fluoride carbon disulfide carbon monoxide hydrochloric acid hydrogen sulfide acetone cyanohydrin phosgene Group XII: Poison B - Meeflaneous a) Gases...b) Liquids sulfur dioxide bromine chlorine boron trifluoride Group XIII: Poison C Group XIV: Poison D Liquid Gas tetraethyl lead fluorine Group XV...with a high and o Nitric acid leaks from a 5,000 gallon storage tank In a growing concentration of electronics industries. Over plant one night and

Blueprint for Acquisition Reform, Version 3.0

DTIC Science & Technology

2008-07-01

represents a substantial and immediate step forward in establishing the Coast Guard as a model mid-sized federal agency for acquisition processes...Blueprint for Acquisition Reform in the U. S. Coast Guard “The Coast Guard must become the model for mid-sized Federal agency acquisition in process...acquisition (DoD 5000 model >CG Major Systems Acquisition Manual) • Deepwater Program Executive Officer (PEO): System of Systems performance-based

NPS-SCAT: Systems Engineering and Payload Subsystem Design, Integration, and Testing of NPS’ First CubeSat

DTIC Science & Technology

2010-06-01

Subsystem Design, Integration, and Testing of NPS’ First CubeSat 6. AUTHOR(S) Jenkins, Robert D. IV 5. FUNDING NUMBERS 7. PERFORMING ORGANIZATION NAME(S...AND ADDRESS(ES) Naval Postgraduate School Monterey, CA 93943-5000 8. PERFORMING ORGANIZATION REPORT NUMBER 9. SPONSORING /MONITORING...Experimental Mission SOIC Small Outline Integrated Circuit SOT Small Outline Transistor SpaceX Space Exploration Technologies Corporation SPI

Test Plan Development for Plastic Ammunition Containers. Volume 1

DTIC Science & Technology

1989-03-15

1850 Black Canyon Stage¶I Packaging division (SMCAR-AEP) Picatinny Phoenix, Arizona 85027 Arsenal, New Jersey 07806-5000 86. NAME OF FUNDING...packaging containers. The report is presented in two separate volumes. Volume I contains the Final Technical Report and includes the analysis of... Division of the U.S. Army Armament Research, Development and Engineering Center. Mr. Jasper C. Griggs and Mr. D. E. Jones served as technical consultants

Threshold of the precedence effect in noise

PubMed Central

Freyman, Richard L.; Griffin, Amanda M.; Zurek, Patrick M.

2014-01-01

Three effects that show a temporal asymmetry in the influence of interaural cues were studied through the addition of masking noise: (1) The transient precedence effect—the perceptual dominance of a leading transient over a similar lagging transient; (2) the ongoing precedence effect—lead dominance with lead and lag components that extend in time; and (3) the onset capture effect—determination by an onset transient of the lateral position of an otherwise ambiguous extended trailing sound. These three effects were evoked with noise-burst stimuli and were compared in the presence of masking noise. Using a diotic noise masker, detection thresholds for stimuli with lead/lag interaural delays of 0/500 μs were compared to those with 500/0 μs delays. None of the three effects showed a masking difference between those conditions, suggesting that none of the effects is operative at masked threshold. A task requiring the discrimination between stimuli with 500/0 and 0/500 μs interaural delays was used to determine the threshold for each effect in noise. The results showed similar thresholds in noise (10–13 dB SL) for the transient and ongoing precedence effects, but a much higher threshold (33 dB SL) for onset capture of an ambiguous trailing sound. PMID:24815272

Accuracy of radiographic caries diagnosis using different X-ray generators.

PubMed

Svenson, B; Petersson, A

1989-05-01

Dental X-ray machines utilizing five different combinations of X-ray generators and tube voltages (Philips Oralix 65 kV, Siemens Heliodent EC 60 kV, Siemens Heliodent 70 kV, Soredex Minray DC 60 kV and Soredex Minray DC 70 kV) were compared with respect to the accuracy of radiographic diagnosis of proximal caries. Nine observers diagnosed proximal caries in radiographs of extracted premolars. The findings of the observers were compared to the actual presence or absence of caries. The ROC-curve technique was used to evaluate differences in diagnostic accuracy between the X-ray machines. The results showed small differences in diagnostic accuracy between the different X-ray generators but they proved to be statistically non-significant.

The continual innovation of commercial PET/CT solutions in nuclear cardiology: Siemens Healthineers.

PubMed

Bendriem, Bernard; Reed, Jessie; McCullough, Kathryn; Khan, Mohammad Raza; Smith, Anne M; Thomas, Damita; Long, Misty

2018-04-10

Cardiac PET/CT is an evolving, non-invasive imaging modality that impacts patient management in many clinical scenarios. Beyond offering the capability to assess myocardial perfusion, inflammatory cardiac pathologies, and myocardial viability, cardiac PET/CT also allows for the non-invasive quantitative assessment of myocardial blood flow (MBF) and myocardial flow reserve (MFR). Recognizing the need for an enhanced comprehension of coronary physiology, Siemens Healthineers implemented a sophisticated solution for the calculation of MBF and MFR in 2009. As a result, each aspect of their innovative scanner and image-processing technology seamlessly integrates into an efficient, easy-to-use workflow for everyday clinical use that maximizes the number of patients who potentially benefit from this imaging modality.

The evolution of void-filled cosmological structures

NASA Technical Reports Server (NTRS)

Regos, Eniko; Geller, Margaret J.

1991-01-01

1D, 2D, and 3D simulations are used here to investigate the salient features in the evolution of void-filled cosmological structures in universes with arbitrary values of Omega. It is found that the growth of a void as a function of time decreases significantly at the time corresponding to Omega = 0.5. In models constructed in 2D and 3D, suitable initial conditions lead to cellular structure with faceted voids similar to those observed in redshift surveys. Matter compressed to planes flows more rapidly toward condensations at the intersections than would be expected for spherical infall. The peculiar streaming velocities for void diameters of 5000 km/s should be observable. The simulations provide a more physical basis and dynamics for the bubbly and Voronois tesselation models used to derive statistical properties of cellular large-scale structure.

Applications of RIGAKU Dmax Rapid II micro-X-ray diffractometer in the analysis of archaeological metal objects

NASA Astrophysics Data System (ADS)

Mozgai, Viktória; Szabó, Máté; Bajnóczi, Bernadett; Weiszburg, Tamás G.; Fórizs, István; Mráv, Zsolt; Tóth, Mária

2017-04-01

During material analysis of archaeological metal objects, especially their inlays or corrosion products, not only microstructure and chemical composition, but mineralogical composition is necessary to be determined. X-ray powder diffraction (XRD) is a widely-used method to specify the mineralogical composition. However, when sampling is not or limitedly allowed due to e.g. the high value of the object, the conventional XRD analysis can hardly be used. Laboratory micro-XRD instruments provide good alternatives, like the RIGAKU Dmax Rapid II micro-X-ray diffractometer, which is a unique combination of a MicroMax-003 third generation microfocus, sealed tube X-ray generator and a curved 'image plate' detector. With this instrument it is possible to measure as small as 10 µm area in diameter on the object. Here we present case studies for the application of the micro-XRD technique in the study of archaeological metal objects. In the first case niello inlay of a Late Roman silver augur staff was analysed. Due to the high value of the object, since it is the only piece known from the Roman Empire, only non-destructive analyses were allowed. To reconstruct the preparation of the niello, SEM-EDX analysis was performed on the niello inlays to characterise their chemical composition and microstructure. Two types of niello are present: a homogeneous, silver sulphide niello (acanthite) and an inhomogeneous silver-copper sulphide niello (exsolution of acanthite and jalpaite or jalpaite and stromeyerite). The micro-X-ray diffractometer was used to verify the mineralogical composition of the niello, supposed on the base of SEM results. In the second case corrosion products of a Late Roman copper cauldron with uncertain provenance were examined, since they may hold clues about the burial conditions (pH, Eh, etc.) of the object. A layer by layer analysis was performed in cross sections of small metal samples by using electron microprobe and micro-X-ray diffractometer. The results show two corrosion zones: 1) the original (internal) surface zone of the metallic copper object was replaced by copper(I) oxide (cuprite), while 2) basic copper(II) carbonate (malachite) was deposited (externally) on the original surface. In our view these two minerals were formed during long-time burial, and protected the cauldron from further corrosion. Rarely copper(I) chloride (nantokite), basic copper(II) trihydroxychloride (atacamite/paratacamite) and basic copper(II) sulphate (brochantite) were also identified in the two corrosion zones. Their uneven distribution on the cauldron and their known formation conditions indicate, that these latter mineral phases may be the results of active corrosion, started possibly after excavation.

17 CFR 150.2 - Position limits.

Code of Federal Regulations, 2011 CFR

2011-04-01

...,500 Soybean Oil 540 5,000 6,500 Soybean Meal 720 5,000 6,500 Minneapolis Grain Exchange Hard Red... Trade Hard Winter Wheat 600 5,000 6,500 1 For purposes of compliance with these limits, positions in the...

Multidimensional MnO2 nanohair-decorated hybrid multichannel carbon nanofiber as an electrode material for high-performance supercapacitors

NASA Astrophysics Data System (ADS)

Jun, Jaemoon; Lee, Jun Seop; Shin, Dong Hoon; Kim, Sung Gun; Jang, Jyongsik

2015-09-01

One-dimensional (1D)-structured nanomaterials represent one of the most attractive candidates for energy-storage systems due to their contribution to design simplicity, fast charge-transportation network, and their allowance for more accessible ion diffusion. In particular, 1D-structured nanomaterials with a highly complex inner-pore configuration enhance functionality by taking advantage of both the hollow and 1D structures. In this study, we report a MnO2 nanohair-decorated, hybrid multichannel carbon nanofiber (Mn_MCNF) fabricated via single-nozzle co-electrospinning of two immiscible polymer solutions, followed by carbonization and redox reactions. With improved ion accessibility, the optimized Mn_MCNF sample (Mn_MCNF_60 corresponding to a reaction duration time of 60 min for optimal MnO2 nanohair growth) exhibited a high specific capacitance of 855 F g-1 and excellent cycling performance with ~87.3% capacitance retention over 5000 cycles.One-dimensional (1D)-structured nanomaterials represent one of the most attractive candidates for energy-storage systems due to their contribution to design simplicity, fast charge-transportation network, and their allowance for more accessible ion diffusion. In particular, 1D-structured nanomaterials with a highly complex inner-pore configuration enhance functionality by taking advantage of both the hollow and 1D structures. In this study, we report a MnO2 nanohair-decorated, hybrid multichannel carbon nanofiber (Mn_MCNF) fabricated via single-nozzle co-electrospinning of two immiscible polymer solutions, followed by carbonization and redox reactions. With improved ion accessibility, the optimized Mn_MCNF sample (Mn_MCNF_60 corresponding to a reaction duration time of 60 min for optimal MnO2 nanohair growth) exhibited a high specific capacitance of 855 F g-1 and excellent cycling performance with ~87.3% capacitance retention over 5000 cycles. Electronic supplementary information (ESI) available: Experimental data includes optical images, TGA, magnified pore distribution curves and supercapacitor device of the MCNF and Mn_MCNF. See DOI: 10.1039/C5NR03616J

Evaluation of the measurement of refractive error by the PowerRefractor: a remote, continuous and binocular measurement system of oculomotor function

PubMed Central

Hunt, O A; Wolffsohn, J S; Gilmartin, B

2003-01-01

Background/aim: The technique of photoretinoscopy is unique in being able to measure the dynamics of the oculomotor system (ocular accommodation, vergence, and pupil size) remotely (working distance typically 1 metre) and objectively in both eyes simultaneously. The aim of this study was to evaluate clinically the measurement of refractive error by a recent commercial photoretinoscopic device, the PowerRefractor (PlusOptiX, Germany). Method: The validity and repeatability of the PowerRefractor was compared to: subjective (non-cycloplegic) refraction on 100 adult subjects (mean age 23.8 (SD 5.7) years) and objective autorefraction (Shin-Nippon SRW-5000, Japan) on 150 subjects (20.1 (4.2) years). Repeatability was assessed by examining the differences between autorefractor readings taken from each eye and by re-measuring the objective prescription of 100 eyes at a subsequent session. Results: On average the PowerRefractor prescription was not significantly different from the subjective refraction, although quite variable (difference +0.05 (0.63) D, p = 0.41) and more negative than the SRW-5000 prescription (by −0.20 (0.72) D, p<0.001). There was no significant bias in the accuracy of the instrument with regard to the type or magnitude of refractive error. The PowerRefractor was found to be repeatable over the prescription range of −8.75D to +4.00D (mean spherical equivalent) examined. Conclusion: The PowerRefractor is a useful objective screening instrument and because of its remote and rapid measurement of both eyes simultaneously is able to assess the oculomotor response in a variety of unrestricted viewing conditions and patient types. PMID:14660462

Evaluation of the measurement of refractive error by the PowerRefractor: a remote, continuous and binocular measurement system of oculomotor function.

PubMed

Hunt, O A; Wolffsohn, J S; Gilmartin, B

2003-12-01

The technique of photoretinoscopy is unique in being able to measure the dynamics of the oculomotor system (ocular accommodation, vergence, and pupil size) remotely (working distance typically 1 metre) and objectively in both eyes simultaneously. The aim of this study was to evaluate clinically the measurement of refractive error by a recent commercial photoretinoscopic device, the PowerRefractor (PlusOptiX, Germany). The validity and repeatability of the PowerRefractor was compared to: subjective (non-cycloplegic) refraction on 100 adult subjects (mean age 23.8 (SD 5.7) years) and objective autorefraction (Shin-Nippon SRW-5000, Japan) on 150 subjects (20.1 (4.2) years). Repeatability was assessed by examining the differences between autorefractor readings taken from each eye and by re-measuring the objective prescription of 100 eyes at a subsequent session. On average the PowerRefractor prescription was not significantly different from the subjective refraction, although quite variable (difference +0.05 (0.63) D, p=0.41) and more negative than the SRW-5000 prescription (by -0.20 (0.72) D, p<0.001). There was no significant bias in the accuracy of the instrument with regard to the type or magnitude of refractive error. The PowerRefractor was found to be repeatable over the prescription range of -8.75D to +4.00D (mean spherical equivalent) examined. The PowerRefractor is a useful objective screening instrument and because of its remote and rapid measurement of both eyes simultaneously is able to assess the oculomotor response in a variety of unrestricted viewing conditions and patient types.

The influences of target properties and deposition times on pulsed laser deposited hydroxyapatite films

NASA Astrophysics Data System (ADS)

Bao, Quanhe; Chen, Chuanzhong; Wang, Diangang; Liu, Junming

2008-11-01

Hydroxyapatite films were produced by pulsed laser deposition from three kinds of hydroxyapatite targets and with different deposition times. A JXA-8800R electron probe microanalyzer (EPMA) with a Link ISIS300 energy spectrum analyzer was used to give the secondary electron image (SE) and determine the element composition of the films. The phases of thin film were analyzed by a D/max-γc X-ray diffractometer (XRD). The Fourier-transform infrared spectroscopy (FT-IR) was used to characterize the hydroxyl, phosphate and other functional groups. The results show that deposited films were amorphous which mainly composed of droplet-like particles and vibration of PO 43- groups. With the target sintering temperature deposition times increasing, the density of droplets is decreased. While with deposition times increasing, the density of droplets is increased. With the target sintering temperature and deposition time increasing, the ratio of Ca/P is increasing and higher than that of theoretical value of HA.

Choice and maintenance of equipment for electron crystallography.

PubMed

Mills, Deryck J; Vonck, Janet

2013-01-01

The choice of equipment for an electron crystallography laboratory will ultimately be determined by the available budget; nevertheless, the ideal lab will have two electron microscopes: a dedicated 300 kV cryo-EM with a field emission gun and a smaller LaB(6) machine for screening. The high-end machine should be equipped with photographic film or a very large CCD or CMOS camera for 2D crystal data collection; the screening microscope needs a mid-size CCD for rapid evaluation of crystal samples. The microscope room installations should provide adequate space and a special environment that puts no restrictions on the collection of high-resolution data. Equipment for specimen preparation includes a carbon coater, glow discharge unit, light microscope, plunge freezer, and liquid nitrogen containers and storage dewars. When photographic film is to be used, additional requirements are a film desiccator, dark room, optical diffractometer, and a film scanner. Having the electron microscopes and ancillary equipment well maintained and always in optimum condition facilitates the production of high-quality data.

Electronic Properties and Device Applications of III-V Compound Semiconductor Native Oxides

DTIC Science & Technology

2006-03-02

MRD X-ray diffractometer with CuKa as the radiation source. The doping level in GaAs was meassured by electrochemical voltage (ECV) using an Accent... hard to prevent the gate metal from overlapping the mesa edge thus creating a parasitic leakage path to the channel42. To reduce the gate leakage

Titration of a Solid Acid Monitored by X-Ray Diffraction

ERIC Educational Resources Information Center

Dungey, Keenan E.; Epstein, Paul

2007-01-01

An experiment is described to introduce students to an important class of solid-state reactions while reinforcing concepts of titration by using a pH meter and a powder X-ray diffractometer. The experiment was successful in teaching students the abstract concepts of solid-state structure and diffraction by applying the diffraction concepts learned…

12 CFR 615.5000 - General responsibilities.

Code of Federal Regulations, 2010 CFR

2010-01-01

....5000 Banks and Banking FARM CREDIT ADMINISTRATION FARM CREDIT SYSTEM FUNDING AND FISCAL AFFAIRS, LOAN POLICIES AND OPERATIONS, AND FUNDING OPERATIONS Funding § 615.5000 General responsibilities. (a) The System... System's funding operations have a significant impact upon the investment community, the general public...

41 CFR 109-43.5000 - Scope of subpart.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 41 Public Contracts and Property Management 3 2012-01-01 2012-01-01 false Scope of subpart. 109-43.5000 Section 109-43.5000 Public Contracts and Property Management Federal Property Management Regulations System (Continued) DEPARTMENT OF ENERGY PROPERTY MANAGEMENT REGULATIONS UTILIZATION AND DISPOSAL...

41 CFR 109-43.5000 - Scope of subpart.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 41 Public Contracts and Property Management 3 2013-07-01 2013-07-01 false Scope of subpart. 109-43.5000 Section 109-43.5000 Public Contracts and Property Management Federal Property Management Regulations System (Continued) DEPARTMENT OF ENERGY PROPERTY MANAGEMENT REGULATIONS UTILIZATION AND DISPOSAL...

Changes in Latitudes, Changes in Attitudes: Narrating a Regime Change

DTIC Science & Technology

2015-03-01

Mossadeq’s alliance with the Tudeh party has led to the violation of the Iranian cultural norm of open hospitality toward foreigners.76 In addition to...6. AUTHOR( S ) Pattric R. Patterson and Matthew D. Ziobro 7. PERFORMING ORGANIZATION NAME( S ) AND ADDRESS(ES) 8. PERFORMING ORGANIZATION Naval...Postgraduate School REPORT NUMBER Monterey, CA 93943-5000 9. SPONSORING /MONITORING AGENCY NAME( S ) AND ADDRESS(ES) 10. SPONSORING/MONITORING N/A AGENCY

Feasibility of imaging superficial palmar arch using micro-ultrasound, 7T and 3T magnetic resonance imaging.

PubMed

Pruzan, Alison N; Kaufman, Audrey E; Calcagno, Claudia; Zhou, Yu; Fayad, Zahi A; Mani, Venkatesh

2017-02-28

To demonstrate feasibility of vessel wall imaging of the superficial palmar arch using high frequency micro-ultrasound, 7T and 3T magnetic resonance imaging (MRI). Four subjects (ages 22-50 years) were scanned on a micro-ultrasound system with a 45-MHz transducer (Vevo 2100, VisualSonics). Subjects' hands were then imaged on a 3T clinical MR scanner (Siemens Biograph MMR) using an 8-channel special purpose phased array carotid coil. Lastly, subjects' hands were imaged on a 7T clinical MR scanner (Siemens Magnetom 7T Whole Body Scanner) using a custom built 8-channel transmit receive carotid coil. All three imaging modalities were subjectively analyzed for image quality and visualization of the vessel wall. Results of this very preliminary study indicated that vessel wall imaging of the superficial palmar arch was feasible with a whole body 7T and 3T MRI in comparison with micro-ultrasound. Subjective analysis of image quality (1-5 scale, 1: poorest, 5: best) from B mode, ultrasound, 3T SPACE MRI and 7T SPACE MRI indicated that the image quality obtained at 7T was superior to both 3T MRI and micro-ultrasound. The 3D SPACE sequence at both 7T and 3T MRI with isotropic voxels allowed for multi-planar reformatting of images and allowed for less operator dependent results as compared to high frequency micro-ultrasound imaging. Although quantitative analysis revealed that there was no significant difference between the three methods, the 7T Tesla trended to have better visibility of the vessel and its wall. Imaging of smaller arteries at the 7T is feasible for evaluating atherosclerosis burden and may be of clinical relevance in multiple diseases.

21 CFR 878.5000 - Nonabsorbable poly(ethylene terephthalate) surgical suture.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Nonabsorbable poly(ethylene terephthalate) surgical suture. 878.5000 Section 878.5000 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES GENERAL AND PLASTIC SURGERY DEVICES Surgical...

21 CFR 878.5000 - Nonabsorbable poly(ethylene terephthalate) surgical suture.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Nonabsorbable poly(ethylene terephthalate) surgical suture. 878.5000 Section 878.5000 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES GENERAL AND PLASTIC SURGERY DEVICES Surgical...

21 CFR 878.5000 - Nonabsorbable poly(ethylene terephthalate) surgical suture.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Nonabsorbable poly(ethylene terephthalate) surgical suture. 878.5000 Section 878.5000 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES GENERAL AND PLASTIC SURGERY DEVICES Surgical...

21 CFR 878.5000 - Nonabsorbable poly(ethylene terephthalate) surgical suture.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Nonabsorbable poly(ethylene terephthalate) surgical suture. 878.5000 Section 878.5000 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES GENERAL AND PLASTIC SURGERY DEVICES Surgical...

[New intensifying screens in clinical radiology. II. Examinations in clinical practice].

PubMed

Freyschmidt, J; Saure, D; Hagemann, G

1976-09-01

A clinically applicable procedure for testing new intensifying rare earth screens, as well as the special Siemens' screen is described. The results are related to universal screens. The film-screen combination alpha 4XD (gadolinium oxysulphide with normal, green sensitive film) results in a reduction of radiation dose to half with detail comparable with universal screens. The Siemens' special screen has similar advantages. Screens with a higher intensification factor and reduction of the mAs to one sixth results in loss of detail. This does not necessarily reduce their clinical use if they are used for appropriate purposes. The results of this clinically orientated technique agreed well with physically objective methods using lead grids. The advantages of the new screens are discussed in terms of their practical application.

Magnetovariational information to improve distortion diagnostics in deep magnetotelluric soundings

NASA Astrophysics Data System (ADS)

Borzotta, E.

2012-09-01

An interpretative experience from nine magnetotelluric soundings was accomplished in the central region of Argentina (32°S-34°S; 63°W-69°W), from the Andean region in the west to the platform zone in the east. To do this, magnetovariational information was used to improve the distortion diagnostics in magnetotelluric curves. Using Pilar Geomagnetic Observatory as a reference site, horizontal magnetic transfer functions were estimated, which were compared with the integrate conductivity at each location in field. As a result, a rather simple methodology is proposed to better approach the accurate positions of normal curves. Results suggest that, in this way, better formal interpretations of soundings may be reached. In addition, a more clear and comprehensible knowledge about the nature of lateral in-homogeneities is obtained; e.g., discovering 3-D effects no suspected from tectonic maps. This methodology seems to be particularly useful when-as in the present case-magnetotelluric soundings are far away each others; i.e., when effective volumes of soundings are not interpenetrated. Horizontal magnetovariational information suggests two elongate conductivity anomalies (about N25°-30°E), possibly associated with deep seated faults belonging to the South American regmatic network. These anomalies would be produced by partial melting in lower crust and possibly in the asthenospheric zone next to Andean Range. Another elongate anomaly (possibly of graphitic nature) is shown in the study region. It seems to be a marginal fault following the border between The Sierras Pampeanas dynamic zone and the South American craton. Magnetotelluric results indicate the study region can be considered as divided in a dynamic belt next to Andean Range and a cratonic zone eastward. The dynamic zone presents a well developed lower crust, with conductances ranging 300-4300 Siemens and depths of about 20-30 km. An asthenosphere close to the Andes with 1000 Siemens of conductance at 74 km depth is also observable. Heat flows of 63-70 mW/m2 are estimated next to Andes and 48 mW/m2, eastward, close to South American platform. The cratonic zone presents a first conductive layer with a conductance of 270 Siemens underneath BUL sounding site, but it does not seem to present lateral development. An intermediate conductive layer is also present in this region, but it does not have so much development. Therefore, this layer would not have asthenospheric character; so, the lithosphere would be tied to upper mantle. Heat flows ranging 40-35 mW/m2 were estimated for this cratonic region.

WE-D-207-03: CT Protocols for Screening and the ACR Designated Lung Screening Program

DOE Office of Scientific and Technical Information (OSTI.GOV)

McNitt-Gray, M.

2015-06-15

In the United States, Lung Cancer is responsible for more cancer deaths than the next four cancers combined. In addition, the 5 year survival rate for lung cancer patients has not improved over the past 40 to 50 years. To combat this deadly disease, in 2002 the National Cancer Institute launched a very large Randomized Control Trial called the National Lung Screening Trial (NLST). This trial would randomize subjects who had substantial risk of lung cancer (due to age and smoking history) into either a Chest X-ray arm or a low dose CT arm. In November 2010, the National Cancermore » Institute announced that the NLST had demonstrated 20% fewer lung cancer deaths among those who were screened with low-dose CT than with chest X-ray. In December 2013, the US Preventive Services Task Force recommended the use of Lung Cancer Screening using low dose CT and a little over a year later (Feb. 2015), CMS announced that Medicare would also cover Lung Cancer Screening using low dose CT. Thus private and public insurers are required to provide Lung Cancer Screening programs using CT to the appropriate population(s). The purpose of this Symposium is to inform medical physicists and prepare them to support the implementation of Lung Screening programs. This Symposium will focus on the clinical aspects of lung cancer screening, requirements of a screening registry for systematically capturing and tracking screening patients and results (such as required Medicare data elements) as well as the role of the medical physicist in screening programs, including the development of low dose CT screening protocols. Learning Objectives: To understand the clinical basis and clinical components of a lung cancer screening program, including eligibility criteria and other requirements. To understand the data collection requirements, workflow, and informatics infrastructure needed to support the tracking and reporting components of a screening program. To understand the role of the medical physicist in implementing Lung Cancer Screening protocols for CT, including utilizing resources such as the AAPM Protocols and the ACR Designated Lung Screening Center program. UCLA Department of Radiology has an Institutional research agreement with Siemens Healthcare; Dr. McNitt-Gray has been a recipient of Research Support from Siemens Healthcare in the past. Dr. Aberle has been a Member of Advisory Boards for the LUNGevity Foundation (2011-present) and Siemens Medical Solutions. (2013)« less

Development of A 5,000 BBL, Rubberized Fabric Fuel Storage Tank, Collapsible,

DTIC Science & Technology

1981-04-01

Note l/ after soil burial. 6/ Reference fuel D is ASTM D-471, 60% iso-octane and 40% toluene. 7/ Retained after 56 days -25- i IGOODYEAR AEROSPACE 0 0...331.7) Pure. 9.I - 9.6 920 0() 09/O 0A) 2.7 ". paum Mese IEststa"t r.e ASIN 11-70 W1 I (ma) 7.3A -n-i I GAC 19-1337 Rev 2 USLE is (continmed) () The...the greater requirement. 5/ Method 5762 except that the specimens were prepared by Note 1/ after soil burial and the number of specimens was reduced

Superfast 3D shape measurement of a flapping flight process with motion based segmentation

NASA Astrophysics Data System (ADS)

Li, Beiwen

2018-02-01

Flapping flight has drawn interests from different fields including biology, aerodynamics and robotics. For such research, the digital fringe projection technology using defocused binary image projection has superfast (e.g. several kHz) measurement capabilities with digital-micromirror-device, yet its measurement quality is still subject to the motion of flapping flight. This research proposes a novel computational framework for dynamic 3D shape measurement of a flapping flight process. The fast and slow motion parts are separately reconstructed with Fourier transform and phase shifting. Experiments demonstrate its success by measuring a flapping wing robot (image acquisition rate: 5000 Hz; flapping speed: 25 cycles/second).

Determination of the precision error of the pulmonary artery thermodilution catheter using an in vitro continuous flow test rig.

PubMed

Yang, Xiao-Xing; Critchley, Lester A; Joynt, Gavin M

2011-01-01

Thermodilution cardiac output using a pulmonary artery catheter is the reference method against which all new methods of cardiac output measurement are judged. However, thermodilution lacks precision and has a quoted precision error of ± 20%. There is uncertainty about its true precision and this causes difficulty when validating new cardiac output technology. Our aim in this investigation was to determine the current precision error of thermodilution measurements. A test rig through which water circulated at different constant rates with ports to insert catheters into a flow chamber was assembled. Flow rate was measured by an externally placed transonic flowprobe and meter. The meter was calibrated by timed filling of a cylinder. Arrow and Edwards 7Fr thermodilution catheters, connected to a Siemens SC9000 cardiac output monitor, were tested. Thermodilution readings were made by injecting 5 mL of ice-cold water. Precision error was divided into random and systematic components, which were determined separately. Between-readings (random) variability was determined for each catheter by taking sets of 10 readings at different flow rates. Coefficient of variation (CV) was calculated for each set and averaged. Between-catheter systems (systematic) variability was derived by plotting calibration lines for sets of catheters. Slopes were used to estimate the systematic component. Performances of 3 cardiac output monitors were compared: Siemens SC9000, Siemens Sirecust 1261, and Philips MP50. Five Arrow and 5 Edwards catheters were tested using the Siemens SC9000 monitor. Flow rates between 0.7 and 7.0 L/min were studied. The CV (random error) for Arrow was 5.4% and for Edwards was 4.8%. The random precision error was ± 10.0% (95% confidence limits). CV (systematic error) was 5.8% and 6.0%, respectively. The systematic precision error was ± 11.6%. The total precision error of a single thermodilution reading was ± 15.3% and ± 13.0% for triplicate readings. Precision error increased by 45% when using the Sirecust monitor and 100% when using the Philips monitor. In vitro testing of pulmonary artery catheters enabled us to measure both the random and systematic error components of thermodilution cardiac output measurement, and thus calculate the precision error. Using the Siemens monitor, we established a precision error of ± 15.3% for single and ± 13.0% for triplicate reading, which was similar to the previous estimate of ± 20%. However, this precision error was significantly worsened by using the Sirecust and Philips monitors. Clinicians should recognize that the precision error of thermodilution cardiac output is dependent on the selection of catheter and monitor model.

The SPRING Nanoenergetics Hub at UTD

DTIC Science & Technology

2008-12-01

synthesis and processing of advanced nanostructured materials, the structure and property characterization needed for materials optimization, the...nano-particles into hexane solvent a deposited films. Here we are modeling that processes to see how the droplet evaporation progresses in time. What...nanofibers was determined by powder X-ray diffraction (XRD) (Scintag XDS 2000 X-ray diffractometer with Cu Ka radiation). The fiber morphology was

Crystal and Vibrational Structure of Energetic 3,5-dinitro 1,3,5-oxadiazinane (DOD) by Single Crystal X-ray Diffractometry and Raman Spectroscopy

DTIC Science & Technology

2018-03-19

calculations using a temperature of 298 K. 15. SUBJECT TERMS 3,5-dinitro-1,3,5-oxadiazinane (DOD), X-ray crystallography , Raman, energetic material...X-ray analysis. 2.2 Characterization X-ray Crystallography . DOD crystals were characterized with a SuperNova, Dualflex, EosS2 diffractometer using

In situ surface/interface x-ray diffractometer for oxide molecular beam epitaxy

DOE PAGES

Lee, J. H.; Tung, I. C.; Chang, S. -H.; ...

2016-01-05

In situ studies of oxide molecular beam epitaxy by synchrotron x-ray scattering has been made possible by upgrading an existing UHV/molecular beam epitaxy (MBE) six-circle diffractometer system. For oxide MBE growth, pure ozone delivery to the chamber has been made available, and several new deposition sources have been made available on a new 12 in. CF (ConFlat, a registered trademark of Varian, Inc.) flange. X-ray diffraction has been used as a major probe for film growth and structures for the system. In the original design, electron diffraction was intended for the secondary diagnostics available without the necessity of the x-raymore » and located at separate positions. Deposition of films was made possible at the two diagnostic positions. And, the aiming of the evaporation sources is fixed to the point between two locations. Ozone can be supplied through two separate nozzles for each location. Also two separate thickness monitors are installed. Finally, additional features of the equipment are also presented together with the data taken during typical oxide film growth to illustrate the depth of information available via in situ x-ray techniques.« less

Low dose radiation damage effects in silicon strip detectors

NASA Astrophysics Data System (ADS)

Wiącek, P.; Dąbrowski, W.

2016-11-01

The radiation damage effects in silicon segmented detectors caused by X-rays have become recently an important research topic driven mainly by development of new detectors for applications at the European X-ray Free Electron Laser (E-XFEL). However, radiation damage in silicon strip is observed not only after extreme doses up to 1 GGy expected at E-XFEL, but also at doses in the range of tens of Gy, to which the detectors in laboratory instruments like X-ray diffractometers or X-ray spectrometers can be exposed. In this paper we report on investigation of radiation damage effects in a custom developed silicon strip detector used in laboratory diffractometers equipped with X-ray tubes. Our results show that significant degradation of detector performance occurs at low doses, well below 200 Gy, which can be reached during normal operation of laboratory instruments. Degradation of the detector energy resolution can be explained by increasing leakage current and increasing interstrip capacitance of the sensor. Another observed effect caused by accumulation of charge trapped in the surface oxide layer is change of charge division between adjacent strips. In addition, we have observed unexpected anomalies in the annealing process.

Concentrating Solar Power Projects - Olivenza 1 | Concentrating Solar Power

Science.gov Websites

Manufacturer: Siemens Turbine Description: 5 extractions Output Type: Steam Rankine Power Cycle Pressure: 100.0 bar Cooling Method: Wet cooling Cooling Method Description: Cooling Towers

Effect of Sc{sup 3+} on structural and magnetic properties of Mn-Zn nano ferrites

DOE Office of Scientific and Technical Information (OSTI.GOV)

Angadi, Jagadeesha V.; Matteppanavar, Shidaling; Srinatha, N.

2016-05-23

In the present investigation, for the first time, we report on the effect of Sc{sup 3+} on the structural and magnetic properties of Mn{sub 0.5}Zn{sub 0.5}Sc{sub y}Fe{sub 2-y}O{sub 4} (y = 0.01, 0.03 and 0.05) nanoferrites synthesized by solution combustion method using the mixture of fuels. As synthesized powders were characterized for the detailed structural analysis by X-ray diffractometer (XRD), Fourier transmission infrared spectroscopy (FTIR) and room temperature magnetic properties by using vibrating sample magnetometer (VSM). The results of XRD and FTIR confirm that the formation of nano crystalline, single-phased Mn-Zn ferrite with cubic spinel structure belongs to Fd-3m spacemore » group. The room temperature magnetic studies shows that, the saturation magnetization (M{sub S}), remanence magnetization (M{sub R}) and magnetic moment (η{sub B}), magnetic particle size (D{sub m}) have found to increase with Sc{sup 3+} ion concentration up to x = 0.3 and then decrease. The values of αY-K and the magnetic particle size (D{sub m}) are found to be in the range of 68-75° and 10-19 nm respectively, with Sc{sup 3+} concentration.« less

75 FR 52437 - IFR Altitudes; Miscellaneous Amendments

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-26

... Part GORDONSVILLE, VA VORTAC LURAY, VA FIX 6100 LURAY, VA FIX *KERRE, VA FIX **6000 *7000--MRA **5000--MOCA *KERRE, VA FIX MARTINSBURG, WV VORTAC.. **6000 *7000--MRA **5000--MOCA Sec. 95.6005 VOR Federal... GORDONSVILLE, VA VORTAC LURAY, VA FIX 6100 LURAY, VA FIX *KERRE, VA FIX **6000 *7000--MRA **5000--MOCA *KERRE...

76 FR 45646 - Culturally Significant Objects Imported for Exhibition Determinations: “5,000 Years of Chinese...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-29

... DEPARTMENT OF STATE [Public Notice: 7540] Culturally Significant Objects Imported for Exhibition Determinations: ``5,000 Years of Chinese Jade Featuring Selections From the National Museum of Taiwan and the... ``5,000 Years of Chinese Jade Featuring Selections from the National Museum of Taiwan and the Arthur M...

Real-time 3D motion tracking for small animal brain PET

NASA Astrophysics Data System (ADS)

Kyme, A. Z.; Zhou, V. W.; Meikle, S. R.; Fulton, R. R.

2008-05-01

High-resolution positron emission tomography (PET) imaging of conscious, unrestrained laboratory animals presents many challenges. Some form of motion correction will normally be necessary to avoid motion artefacts in the reconstruction. The aim of the current work was to develop and evaluate a motion tracking system potentially suitable for use in small animal PET. This system is based on the commercially available stereo-optical MicronTracker S60 which we have integrated with a Siemens Focus-220 microPET scanner. We present measured performance limits of the tracker and the technical details of our implementation, including calibration and synchronization of the system. A phantom study demonstrating motion tracking and correction was also performed. The system can be calibrated with sub-millimetre accuracy, and small lightweight markers can be constructed to provide accurate 3D motion data. A marked reduction in motion artefacts was demonstrated in the phantom study. The techniques and results described here represent a step towards a practical method for rigid-body motion correction in small animal PET. There is scope to achieve further improvements in the accuracy of synchronization and pose measurements in future work.

Effect of 5,000 ppm Fluoride Dentifrice or 1,100 ppm Fluoride Dentifrice Combined with Acidulated Phosphate Fluoride on Caries Lesion Inhibition and Repair.

PubMed

Fernández, Constanza E; Tenuta, Livia Maria Andaló; Del Bel Cury, Altair Antoninha; Nóbrega, Diego Figueiredo; Cury, Jaime Aparecido

2017-01-01

High fluoride dentifrice (FD; 5,000 ppm F) has been recommended to arrest root dentine lesions and to control enamel caries in high-risk patients. Also, standard FD (1,100 ppm F) in combination with professional fluoride application has been recommended to control dentine caries, but the effect of this combination on enamel has been considered modest. Considering the lack of evaluation comparing the use of 5,000 ppm FD (5,000-FD) versus acidulated phosphate fluoride (APF) application combined with 1,100 ppm FD (1,100-FD) on the inhibition and repair of caries lesions in both enamel and dentine, we conducted this in situ, double-blind, crossover study of 3 phases of 14 days. In each phase, 18 volunteers wore palatal appliances containing enamel and root dentine specimens, either sound or carious, to evaluate the effect of the treatments on the inhibition or repair of caries lesions, respectively. The treatments were non-FD (negative control), 5,000-FD, or 1 APF gel application on dental specimens combined with 1,100-FD used twice per day (APF + 1,100-FD). The reduction of demineralization and enhancement of remineralization were assessed by surface and cross-sectional hardness. Fluoride concentration was determined on dental specimens and on the formed biofilm. For enamel, APF + 1,100-FD and 5,000-FD did not differ regarding the inhibition of demineralization and repair of caries lesions. However, for dentine the difference between these treatments was inconclusive because while APF + 1,100-FD was more effective than 5,000-FD in caries lesion reduction and repair, 5,000-FD was more effective than APF + 1,100-FD in the reduction of surface demineralization. Therefore, the findings show that the combination of APF + 1,100-FD is as effective as 5,000-FD in enamel inhibition of demineralization and enhancement of remineralization. © 2017 S. Karger AG, Basel.

Gulf Stream Temperature, Salinity and Transport During the Last Millennium

DTIC Science & Technology

2006-02-01

their relationship to 9 one another and to proxies of solar variability. Chapter 3 addresses the temperature and salinity components of the...Florida Current 618Oc varied coherently with proxies of atmospheric radiocarbon at low frequencies over 10 the last 5,000 years, suggesting a link...cooling that began around 1000 A.D. models and proxies used. This two-stage character of the LIA is not apparent in the Florida margin cores. 6.4

Metropolitan Spokane Region Water Resources Study. Appendix D. Wastewater Generation and Treatment

DTIC Science & Technology

1976-01-01

equipment and toxic to the anaerobic organisms in the digesters . Plant operating policy requires that, when the influent chloride concentration reaches...sheep e. 55,000 turkeys f. 100,000 laying hens or broilers g. 30,000 laying hens or broilers wiL!, liquid manure handling systems h. 5000 ducks i...study area is currently off from the levels indicated in the census due to unfavorable feed and price levels. There is essentially no broiler production

STARS Conceptual Framework for Reuse Process (CFRP). Volume 1. Definition. Version 3.0

DTIC Science & Technology

1993-10-25

Command, USAF Hanscom AFB, MA 01731-5000 DTIC QUALITY IN ,,P.’±U4) D Prepared by: The Boeing Company , IBM, Defense & Space Group, Federal Systems... Company , Unisys Corporation, P.O. Box 3999, MS 87-37 800 N. Frederick Pike, 12010 Sunrise Valley Drive, Seattle, WA 98124-2499 Gaithersburg, MD 20879...34 3.2.1.1 Domain Analysis and Modeling Process Category ............ 38 3.2.1.2 Domain Architecture Development Process

Steady-State and Dynamic Desorption of Organic Vapor From Activated Carbon With Electrothermal Swing Adsorption

DTIC Science & Technology

2007-06-01

41, 5063-5069 10.1021/es0703022 CCC: $37.00  2007 American Chemical Society VOL. 41, NO. 14, 2007 / ENVIRONMENTAL SCIENCE & TECHNOLOGY 9 5063...system. 5064 9 ENVIRONMENTAL SCIENCE & TECHNOLOGY / VOL. 41, NO. 14, 2007 occurred with variable pre-defined set-points ranging from 250 to 5000 ppmv...and (d) power and cumulative energy deposited to the ACFC. 5066 9 ENVIRONMENTAL SCIENCE & TECHNOLOGY / VOL. 41, NO. 14, 2007 (Figure 4). Maximum

Analysis of Space Station Operations in the Space Debris Environment.

DTIC Science & Technology

1984-12-01

o, a Itmd, a Ithi , umco, s atpop, s tplo, a atpm d , aatphi , + expobj,dlo,dmd,dhi,nexplo,nexpuid,nexphi, colide , + objlo,objmd,objhi,cobjlo,cobjmd...tisoic, tiioc,flumco, + soivsl,soivsm, soivsh,numrun double precision c, colide ,rholo,rhomd, rhoh. equivalence(nset(l ),qset(l)) net-7 5000 ncrdr-5...del tlo,del tmd,del thi, + *1 tlo,altad,althi ,numco,satpop,satplo,aatpmd,satphi, + expobj,dlo,dad,dhi,nexplo,nexpudnexphi, colide , + objlo

Continuum Mechanics Based Bi-linear Shear Deformable Shell Element Using Absolute Nodal Coordinate Formulation

DTIC Science & Technology

2014-03-07

Skinnarilankatu 34, 53850 Lappeenranta, Finland Paramsothy Jayakumar US Army RDECOM TARDEC 6501 E. 11 Mile Road Warren, MI 48397-5000 Hiroyuki Sugiyama...ELEMENT NUMBER 6. AUTHOR(S) Hiroki Yamashita; Antti Valkeapaa; Paramsothy Jayakumar ; Hiroyuki Sugiyama 5d. PROJECT NUMBER 5e. TASK NUMBER 5f. WORK...Computers and Information in Engineering Conference, Chicago, IL, USA [9] Valkeapää, A. I., Yamashita, H., Jayakumar , P. and Sugiyama, H., “Gradient

Advanced Rotorcraft Transmission (ART) program

NASA Technical Reports Server (NTRS)

Heath, Gregory F.; Bossler, Robert B., Jr.

1993-01-01

Work performed by the McDonnell Douglas Helicopter Company and Lucas Western, Inc. within the U.S. Army/NASA Advanced Rotorcraft Transmission (ART) Program is summarized. The design of a 5000 horsepower transmission for a next generation advanced attack helicopter is described. Government goals for the program were to define technology and detail design the ART to meet, as a minimum, a weight reduction of 25 percent, an internal noise reduction of 10 dB plus a mean-time-between-removal (MTBR) of 5000 hours compared to a state-of-the-art baseline transmission. The split-torque transmission developed using face gears achieved a 40 percent weight reduction, a 9.6 dB noise reduction and a 5270 hour MTBR in meeting or exceeding the above goals. Aircraft mission performance and cost improvements resulting from installation of the ART would include a 17 to 22 percent improvement in loss-exchange ratio during combat, a 22 percent improvement in mean-time-between-failure, a transmission acquisition cost savings of 23 percent of $165K, per unit, and an average transmission direct operating cost savings of 33 percent, or $24K per flight hour. Face gear tests performed successfully at NASA Lewis are summarized. Also, program results of advanced material tooth scoring tests, single tooth bending tests, Charpy impact energy tests, compact tension fracture toughness tests and tensile strength tests are summarized.

Effect of optical digitizer selection on the application accuracy of a surgical localization system-a quantitative comparison between the OPTOTRAK and flashpoint tracking systems

NASA Technical Reports Server (NTRS)

Li, Q.; Zamorano, L.; Jiang, Z.; Gong, J. X.; Pandya, A.; Perez, R.; Diaz, F.

1999-01-01

Application accuracy is a crucial factor for stereotactic surgical localization systems, in which space digitization camera systems are one of the most critical components. In this study we compared the effect of the OPTOTRAK 3020 space digitization system and the FlashPoint Model 3000 and 5000 3D digitizer systems on the application accuracy for interactive localization of intracranial lesions. A phantom was mounted with several implantable frameless markers which were randomly distributed on its surface. The target point was digitized and the coordinates were recorded and compared with reference points. The differences from the reference points represented the deviation from the "true point." The root mean square (RMS) was calculated to show the differences, and a paired t-test was used to analyze the results. The results with the phantom showed that, for 1-mm sections of CT scans, the RMS was 0.76 +/- 0. 54 mm for the OPTOTRAK system, 1.23 +/- 0.53 mm for the FlashPoint Model 3000 3D digitizer system, and 1.00 +/- 0.42 mm for the FlashPoint Model 5000 system. These preliminary results showed that there is no significant difference between the three tracking systems, and, from the quality point of view, they can all be used for image-guided surgery procedures. Copyright 1999 Wiley-Liss, Inc.

Effect of optical digitizer selection on the application accuracy of a surgical localization system-a quantitative comparison between the OPTOTRAK and flashpoint tracking systems.

PubMed

Li, Q; Zamorano, L; Jiang, Z; Gong, J X; Pandya, A; Perez, R; Diaz, F

1999-01-01

Application accuracy is a crucial factor for stereotactic surgical localization systems, in which space digitization camera systems are one of the most critical components. In this study we compared the effect of the OPTOTRAK 3020 space digitization system and the FlashPoint Model 3000 and 5000 3D digitizer systems on the application accuracy for interactive localization of intracranial lesions. A phantom was mounted with several implantable frameless markers which were randomly distributed on its surface. The target point was digitized and the coordinates were recorded and compared with reference points. The differences from the reference points represented the deviation from the "true point." The root mean square (RMS) was calculated to show the differences, and a paired t-test was used to analyze the results. The results with the phantom showed that, for 1-mm sections of CT scans, the RMS was 0.76 +/- 0. 54 mm for the OPTOTRAK system, 1.23 +/- 0.53 mm for the FlashPoint Model 3000 3D digitizer system, and 1.00 +/- 0.42 mm for the FlashPoint Model 5000 system. These preliminary results showed that there is no significant difference between the three tracking systems, and, from the quality point of view, they can all be used for image-guided surgery procedures. Copyright 1999 Wiley-Liss, Inc.

Toxicology and carcinogenesis studies of sodium nitrite (CAS NO. 7632-00-0) in F344/N rats and B6C3F1 mice (drinking water studies).

PubMed

2001-05-01

Sodium nitrite is used as a color fixative and preservative in meats and fish. It is also used in manufacturing diazo dyes, nitroso compounds, and other organic compounds; in dyeing and printing textile fabrics and bleaching fibers; in photography; as a laboratory reagent and a corrosion inhibitor; in metal coatings for phosphatizing and detinning; and in the manufacture of rubber chemicals. Sodium nitrite also has been used in human and veterinary medicine as a vasodilator, a bronchial dilator, an intestinal relaxant, and an antidote for cyanide poisoning. Sodium nitrite was nominated by the FDA for toxicity and carcinogenesis studies based on its widespread use in foods. Male and female F344/N rats and B6C3F1 mice were exposed to sodium nitrite (99% pure) in drinking water for 14 weeks or 2 years. Genetic toxicology studies were conducted in Salmonella typhimurium, rat and mouse bone marrow, and mouse peripheral blood. 14-WEEK STUDY IN RATS: Groups of 10 male and 10 female rats were exposed to 0, 375, 750, 1500, 3,000, or 5000 ppm sodium nitrite (equivalent to average daily doses of approximately 30, 55, 115, 200, or 310 mg sodium nitrite/kg body weight to males and 40, 80, 130, 225, or 345 mg/kg to females) in drinking water for 14 weeks. Clinical pathology study groups of 15 male and 15 female rats were exposed to the same concentrations for 70 or 71 days. One female exposed to 3000 ppm died before the end of the study. Body weights of males exposed to 3000 or 5000 ppm and females exposed to 5000 ppm were significantly less than those of the controls. Water consumption by 5000 ppm males and 3000 and 5000 ppm females was less than that by the controls at weeks 2 and 14. Clinical findings related to sodium nitrite exposure included brown discoloration in the eyes and cyanosis of the mouth, tongue, ears, and feet of males exposed to 3000 or 5000 ppm and of females exposed to 1500 ppm or greater. Reticulocyte counts were increased in males and females exposed to 3000 or 5000 ppm. The erythron was decreased on day 19 but increased by week 14 in males and females exposed to 5000 ppm. Methemoglobin concentrations were elevated in almost all exposed groups throughout the 14 week study; a no-observed-adverse-effect level was not achieved. The relative kidney and spleen weights of males and females exposed to 3000 or 5000 ppm were significantly greater than those of the controls. Sperm motility in 1500 and 5000 ppm males was significantly decreased. Increased erythropoietic activity in the bone marrow of exposed males and females was observed. The incidences of squamous cell hyperplasia of the forestomach in 5000 ppm males and females were significantly increased. 14-WEEK STUDY IN MICE: Groups of 10 male and 10 female B6C3F1 mice were exposed to 0, 375, 750, 1500, 3000, or 5000 ppm sodium nitrite (equivalent to average daily doses of approximately 90, 190, 345, 750, or 990 mg/kg to males and 120, 240, 445, 840, or 1230 mg/kg to females) in drinking water for 14 weeks. Body weights of males exposed to 5000 ppm were significantly less than those of the controls. Water consumption by males exposed to 1500 ppm or greater was slightly less than that by the controls at week 13. Relative spleen weights of 3000 and 5000 ppm males and absolute and relative heart, kidney, liver, and spleen weights of females exposed to 3000 or 5000 ppm were greater than those of the control groups. Sperm motility was decreased in 5000 ppm males, and the estrous cycles of 1500 and 5000 ppm females were significantly longer than in the controls. There were increased incidences of squamous cell hyperplasia of the forestomach in 5000 ppm males and females, extramedullary hematopoiesis of the spleen in 3000 and 5000 ppm males and 1500 ppm or greater females, and degeneration of the testis in 3000 and 5000 ppm males. 2-YEAR STUDY IN RATS: Groups of 50 male and 50 female rats were exposed to 0, 750, 1500, or 3000 ppm sodium nitrite (equivalent to average daily doses of approximately 35, 70, or 130 mg/kg to males and 40, 8d 40, 80, or 150 mg/kg to females) in drinking water for 2 years. For toxicokinetic studies of plasma nitrite and blood methemoglobin, 10 male and 10 female special study rats were exposed to the same concentrations for 12 months. Survival of exposed groups was similar to that of the controls. Mean body weights of males and females exposed to 3000 ppm were less than those of the controls throughout the study. Water consumption by males and females exposed to 3000 ppm was less than that by the controls throughout the study, and that by the other exposed groups was generally less after week 14. The incidences of hyperplasia of the forestomach epithelium in males and females exposed to 3000 ppm were significantly greater than those in the control groups. The incidence of fibroadenoma of the mam mary gland was significantly increased in females exposed to 1500 ppm, and the incidences of multiple fibroadenoma were increased in 750 ppm and 1500 ppm females; however, these neoplasms occur with a high background incidence, and no increase was seen in the 3000 ppm group. The incidences of mononuclear cell leukemia were significantly decreased in males and females exposed to 1500 or 3000 ppm. 2-YEAR STUDY IN MICE: Groups of 50 male and 50 female B6C3F1 mice were exposed to 0, 750, 1500, or 3000 ppm sodium nitrite (equivalent to average daily doses of approximately 60, 120, or 220 mg/kg to males and 45, 90, or 165 mg/kg to females) in drinking water for 2 years. Survival of exposed groups was similar to that of the controls; mean body weights of 3000 ppm females were less than those of the controls throughout the study. Exposed groups generally consumed less water than the control groups. The incidences of squamous cell papilloma or carcinoma (combined) in the forestomach of female mice occurred with a positive trend. The incidence of hyperplasia of the glandular stomach epithelium was significantly greater in 3000 ppm males than in the controls. Sodium nitrite was mutagenic in Salmonella typhimurium strain TA100, with and without Aroclor 1254-induced hamster and rat liver S9 enzymes; no mutagenicity was observed in strain TA98. Results of acute bone marrow micronucleus tests with sodium nitrite in male rats and mice by intraperitoneal injection were negative. In addition, a peripheral blood micronucleus assay conducted with mice from the 14-week study gave negative results. Under the conditions of this 2-year drinking water study, there was no evidence of carcinogenic activity of sodium nitrite in male or female F344/N rats exposed to 750, 1500, or 3000 ppm. There was no evidence of carcinogenic activity of sodium nitrite in male B6C3F1 mice exposed to 750, 1500, or 3000 ppm. There was equivocal evidence of carcinogenic activity of sodium nitrite in female B6C3F1 mice based on the positive trend in the incidences of squamous cell papilloma or carcinoma (combined) of the forestomach. Exposure to sodium nitrite in drinking water resulted in increased incidences of epithelial hyperplasia in the forestomach of male and female rats and in the glandular stomach of male mice. Decreased incidences of mononuclear cell leukemia occurred in male and female rats.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Valenti, M.

This paper reports that as tougher emissions standards take hold throughout the industrialized world, manufacturers such as GE, Siemens, Foster Wheeler, and Asea Brown Boveri are designing advanced combined-cycle equipment that offers improved environmental performance without sacrificing power efficiency.

78 FR 9583 - IFR Altitudes; Miscellaneous Amendments

Federal Register 2010, 2011, 2012, 2013, 2014

2013-02-11

... is Amended to Read in Part LAWRENCEVILLE, VA VORTAC..... *MANGE, VA FIX....... **4000 *5000--MRA.... **5000 *5000--MRA **1800--MOCA **2000--GNSS MEA Sec. 95.6157 VOR Federal Airway V157 is Amended to Read... BND 8600 S BND 10000 *12000--MRA Sec. 95.6301 VOR Federal Airway V301 is Amended to Read in Part SANTA...

27 CFR 25.164 - Quarterly and semimonthly returns.

Code of Federal Regulations, 2010 CFR

2010-04-01

... BUREAU, DEPARTMENT OF THE TREASURY LIQUORS BEER Tax on Beer Preparation and Remittance of Tax Returns... on beer (unless prepaid) by return on Form 5000.24. The brewer shall file Form 5000.24 as a return... file a return on Form 5000.24 for each return period even though no beer was removed for consumption or...

27 CFR 25.164 - Quarterly and semimonthly returns.

Code of Federal Regulations, 2012 CFR

2012-04-01

... BUREAU, DEPARTMENT OF THE TREASURY LIQUORS BEER Tax on Beer Preparation and Remittance of Tax Returns... on beer (unless prepaid) by return on Form 5000.24. The brewer shall file Form 5000.24 as a return... file a return on Form 5000.24 for each return period even though no beer was removed for consumption or...

27 CFR 25.164 - Quarterly and semimonthly returns.

Code of Federal Regulations, 2014 CFR

2014-04-01

... BUREAU, DEPARTMENT OF THE TREASURY ALCOHOL BEER Tax on Beer Preparation and Remittance of Tax Returns... on beer (unless prepaid) by return on Form 5000.24. The brewer shall file Form 5000.24 as a return... file a return on Form 5000.24 for each return period even though no beer was removed for consumption or...

27 CFR 25.164 - Quarterly and semimonthly returns.

Code of Federal Regulations, 2013 CFR

2013-04-01

... BUREAU, DEPARTMENT OF THE TREASURY ALCOHOL BEER Tax on Beer Preparation and Remittance of Tax Returns... on beer (unless prepaid) by return on Form 5000.24. The brewer shall file Form 5000.24 as a return... file a return on Form 5000.24 for each return period even though no beer was removed for consumption or...

@NWTC Newsletter: Winter 2015 | Wind | NREL

Science.gov Websites

Energy Laboratory). (2014). 8 pp.; NREL Report No. BR-5000-63254. Jimenez, T.; Tegen, S. (2015). Economic Report No. TP-5000-61727. Lieberman-Cribbin, W.; Draxl, C.; Clifton, A. (2014). Guide to Using the WIND Toolkit Validation Code. 31 pp.; NREL Report No. TP-5000-62595. Bulaevskaya, V.; Wharton, S.; Clifton, A

27 CFR 25.164 - Quarterly and semimonthly returns.

Code of Federal Regulations, 2011 CFR

2011-04-01

... BUREAU, DEPARTMENT OF THE TREASURY LIQUORS BEER Tax on Beer Preparation and Remittance of Tax Returns... on beer (unless prepaid) by return on Form 5000.24. The brewer shall file Form 5000.24 as a return... file a return on Form 5000.24 for each return period even though no beer was removed for consumption or...

26 CFR 1.5000A-4 - Computation of shared responsibility payment.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 26 Internal Revenue 13 2014-04-01 2014-04-01 false Computation of shared responsibility payment. 1.5000A-4 Section 1.5000A-4 Internal Revenue INTERNAL REVENUE SERVICE, DEPARTMENT OF THE TREASURY... individual was born. For example, an individual born on March 1, 1999, attains the age of 18 on March 1, 2017...

Design of monitoring system for mail-sorting based on the Profibus S7 series PLC

NASA Astrophysics Data System (ADS)

Zhang, W.; Jia, S. H.; Wang, Y. H.; Liu, H.; Tang, G. C.

2017-01-01

With the rapid development of the postal express, the workload of mail sorting is increasing, but the automatic technology of mail sorting is not mature enough. In view of this, the system uses Siemens S7-300 PLC as the main station controller, PLC of Siemens S7-200/400 is from the station controller, through the man-machine interface configuration software MCGS, PROFIBUS-DP communication, RFID technology and mechanical sorting hand achieve mail classification sorting monitoring. Among them, distinguish mail-sorting by scanning RFID posted in the mail electronic bar code (fixed code), the system uses the corresponding controller on the acquisition of information processing, the processed information transmit to the sorting manipulator by PROFIBUS-DP. The system can realize accurate and efficient mail sorting, which will promote the development of mail sorting technology.

Characterization of linear accelerator X-ray source size using a laminated beam-spot camera.

PubMed

Yeboah, Collins

2011-05-10

A laminated beam-spot camera of length 20 cm and effective cross-sectional area 2.5 cm × 3 cm was designed and constructed for the measurement of X-ray beam-spot sizes on different models of Siemens accelerators. With the accelerator gantry at 180° and camera positioned on an accessory tray holder, an XV film placed in contact with the camera at the distal end of it detected those X-rays that were transmitted through the camera. The FWHM of the detected X-ray intensity profile in the gun-target (G-T) direction or the orthogonal A-B direction was used as a measure of the beam-spot size in that direction. Siemens Mevatron MXEs exhibited a beam-spot size of 1.7 ± 0.2 mm in both the in-plane and cross-plane directions for 6 MV photon beams. The beam-spot size observed for a Mevatron MDX-2 was larger by up to 1 mm, and also was different for the in-plane and cross-plane directions. For Siemens PRIMUS accelerators, the beam-spot size in the in-plane direction was found to fall in the range 2.0-2.2 ± 0.2 mm, whereas the beam-spot size in the cross-plane direction fell within 1.7-1.9 ± 0.2 mm for 6, 10, and 18 MV photon beams. Assessment of long-term stability of the beam-spot size shows the spot size remains fairly stable over time.

Transforming an industrial giant. Interview by Thomas A. Stewart and Louise O'Brien.

PubMed

von Pierer, Heinrich

2005-02-01

In his 12 years at the helm of Siemens, CEO Heinrich von Pierer designed and directed a major transformation. Taking this German icon from a technically superb but slow-moving industrial giantto a disciplined yet nimble multinational has posed enormous challenges. Since 1992, Siemens has revamped its portfolio of businesses, expanded its reach into 192 countries, and created a more local-market-driven culture, gaining recognition as one of the best-managed and most competitive companies in the world. In this edited interview with HBR editor Thomas A. Stewart and consulting editor Louise O'Brien, von Pierer describes the requirements for transformation and culture change and how he broke down historical barriers at Siemens. He shares his insights about portfolio restructuring, his lessons from competing with GE, and the pros and cons of being based in Europe versus America. He reflects on the true start of globalization after the fall of the Berlin wall and on how dramatically the company needed to change in order to counter the resulting pricing pressures across all of its businesses. He talks, too, about the biggest challenge on his successor's desk-"the particular challenge of China;" he says. Amid all these topics, von Pierer reiterates the importance of people: "We all talk about people as our most important resource, but as a matter of fact, who's really taking care of people?... We need [their] backing. We can't afford to run into a situation where people no longer accept what we do."

In vivo 1D and 2D correlation MR spectroscopy of the soleus muscle at 7T

PubMed Central

Ramadan, Saadallah; Ratai, Eva-Maria; Wald, Lawrence L.; Mountford, Carolyn E.

2013-01-01

Aim This study aims to (1) undertake and analyse 1D and 2D MR correlation spectroscopy from human soleus muscle in vivo at 7T, and (2) determine T1 and T2 relaxation time constants at 7T field strength due to their importance in sequence design and spectral quantitation. Method Six healthy, male volunteers were consented and scanned on a 7T whole-body scanner (Siemens AG, Erlangen, Germany). Experiments were undertaken using a 28 cm diameter detunable birdcage coil for signal excitation and an 8.5 cm diameter surface coil for signal reception. The relaxation time constants, T1 and T2 were recorded using a STEAM sequence, using the ‘progressive saturation’ method for the T1 and multiple echo times for T2. The 2D L-Correlated SpectroscopY (L-COSY) method was employed with 64 increments (0.4 ms increment size) and eight averages per scan, with a total time of 17 min. Results T1 and T2 values for the metabolites of interest were determined. The L-COSY spectra obtained from the soleus muscle provided information on lipid content and chemical structure not available, in vivo, at lower field strengths. All molecular fragments within multiple lipid compartments were chemically shifted by 0.20–0.26 ppm at this field strength. 1D and 2D L-COSY spectra were assigned and proton connectivities were confirmed with the 2D method. Conclusion In vivo 1D and 2D spectroscopic examination of muscle can be successfully recorded at 7T and is now available to assess lipid alterations as well as other metabolites present with disease. T1 and T2 values were also determined in soleus muscle of male healthy volunteers. PMID:20206561

Cellulose Tailored Anatase TiO2 Nanospindles in Three-Dimensional Graphene Composites for High-Performance Supercapacitors.

PubMed

Ding, Yangbin; Bai, Wei; Sun, Jinhua; Wu, Yu; Memon, Mushtaque A; Wang, Chao; Liu, Chengbin; Huang, Yong; Geng, Jianxin

2016-05-18

The morphologies of transition metal oxides have decisive impact on the performance of their applications. Here, we report a new and facile strategy for in situ preparation of anatase TiO2 nanospindles in three-dimensional reduced graphene oxide (RGO) structure (3D TiO2@RGO) using cellulose as both an intermediate agent eliminating the negative effect of graphene oxide (GO) on the growth of TiO2 crystals and as a structure-directing agent for the shape-controlled synthesis of TiO2 crystals. High-resolution transmission electron microscopy and X-ray diffractometer analysis indicated that the spindle shape of TiO2 crystals was formed through the restriction of the growth of high energy {010} facets due to preferential adsorption of cellulose on these facets. Because of the 3D structure of the composite, the large aspect ratio of the TiO2 nanospindles, and the exposed high-energy {010} facets of the TiO2 crystals, the 3D TiO2@RGO(Ce 1.7) exhibited excellent capacitive performance as an electrode material for supercapacitors, with a high specific capacitance (ca. 397 F g(-1)), a high energy density (55.7 Wh kg(-1)), and a high power density (1327 W kg(-1)) on the basis of the masses of RGO and TiO2. These levels of capacitive performance far exceed those of previously reported TiO2-based composites.

JPRS Report Science & Technology Japan

DTIC Science & Technology

1989-06-02

Electronics •Superconducting Wiring in LSI •One Wafer Computer •Josephson Devices •SQUID Devices Infrared Sensor Magnetic Sensor •Superconducting...Guinier- de Wolff monochromatic focusing camera (CoK* radiation) and with Philips APD-10 auto-powder diffractometer (CuKÄ radiation). Pure Si was used as...crystallized and smooth surface. The values indicated in Fig. 2 were the thickness monitored by a quartz oscillating sensor located near the

Single-crystal diffraction instrument TriCS at SINQ

NASA Astrophysics Data System (ADS)

Schefer, J.; Könnecke, M.; Murasik, A.; Czopnik, A.; Strässle, Th; Keller, P.; Schlumpf, N.

2000-03-01

The single-crystal diffractometer TriCS at the Swiss Continuous Spallation Source (SINQ) is presently in the commissioning phase. A two-dimensional wire detector produced by EMBL was delivered in March 1999. The instrument is presently tested with a single detector. First measurements on magnetic structures have been performed. The instrument is remotely controlled using JAVA-based software and a UNIX DEC-α host computer.

Standard Reference Material (SRM 1990) for Single Crystal Diffractometer Alignment

USGS Publications Warehouse

Wong-Ng, W.; Siegrist, T.; DeTitta, G.T.; Finger, L.W.; Evans, H.T.; Gabe, E.J.; Enright, G.D.; Armstrong, J.T.; Levenson, M.; Cook, L.P.; Hubbard, C.R.

2001-01-01

An international project was successfully completed which involved two major undertakings: (1) a round-robin to demonstrate the viability of the selected standard and (2) the certification of the lattice parameters of the SRM 1990, a Standard Reference Material?? for single crystal diffractometer alignment. This SRM is a set of ???3500 units of Cr-doped Al2O3, or ruby spheres [(0 420.011 mole fraction % Cr (expanded uncertainty)]. The round-robin consisted of determination of lattice parameters of a pair of crystals' the ruby sphere as a standard, and a zeolite reference to serve as an unknown. Fifty pairs of crystals were dispatched from Hauptman-Woodward Medical Research Institute to volunteers in x-ray laboratories world-wide. A total of 45 sets of data was received from 32 laboratories. The mean unit cell parameters of the ruby spheres was found to be a=4.7608 A?? ?? 0.0062 A??, and c=12.9979 A?? ?? 0.020 A?? (95 % intervals of the laboratory means). The source of errors of outlier data was identified. The SRM project involved the certification of lattice parameters using four well-aligned single crystal diffractometers at (Bell Laboratories) Lucent Technologies and at NRC of Canada (39 ruby spheres), the quantification of the Cr content using a combined microprobe and SEM/EDS technique, and the evaluation of the mosaicity of the ruby spheres using a double-crystal spectrometry method. A confirmation of the lattice parameters was also conducted using a Guinier-Ha??gg camera. Systematic corrections of thermal expansion and refraction corrections were applied. These rubies_ are rhombohedral, with space group R3c. The certified mean unit cell parameters are a=4.76080 ?? 0.00029 A??, and c=12 99568 A?? ?? 0.00087 A?? (expanded uncertainty). These certified lattice parameters fall well within the results of those obtained from the international round-robin study. The Guinier-Ha??gg transmission measurements on five samples of powdered rubies (a=4.7610 A?? ?? 0.0013 A??, and c=12.9954 A?? ?? 0.0034 A??) agreed well with the values obtained from the single crystal spheres.

Standard Reference Material (SRM 1990) For Single Crystal Diffractometer Alignment

PubMed Central

Wong-Ng, W.; Siegrist, T.; DeTitta, G. T.; Finger, L. W.; Evans, H. T.; Gabe, E. J.; Enright, G. D.; Armstrong, J. T.; Levenson, M.; Cook, L. P.; Hubbard, C. R.

2001-01-01

An international project was successfully completed which involved two major undertakings: (1) a round-robin to demonstrate the viability of the selected standard and (2) the certification of the lattice parameters of the SRM 1990, a Standard Reference Material® for single crystal diffractometer alignment. This SRM is a set of ≈3500 units of Cr-doped Al2O3, or ruby spheres [(0.420.011 mole fraction % Cr (expanded uncertainty)]. The round-robin consisted of determination of lattice parameters of a pair of crystals: the ruby sphere as a standard, and a zeolite reference to serve as an unknown. Fifty pairs of crystals were dispatched from Hauptman-Woodward Medical Research Institute to volunteers in x-ray laboratories world-wide. A total of 45 sets of data was received from 32 laboratories. The mean unit cell parameters of the ruby spheres was found to be a=4.7608 ű0.0062 Å, and c=12.9979 ű0.020 Å (95 % intervals of the laboratory means). The source of errors of outlier data was identified. The SRM project involved the certification of lattice parameters using four well-aligned single crystal diffractometers at (Bell Laboratories) Lucent Technologies and at NRC of Canada (39 ruby spheres), the quantification of the Cr content using a combined microprobe and SEM/EDS technique, and the evaluation of the mosaicity of the ruby spheres using a double-crystal spectrometry method. A confirmation of the lattice parameters was also conducted using a Guinier-Hägg camera. Systematic corrections of thermal expansion and refraction corrections were applied. These rubies– are rhombohedral, with space group R3¯c. The certified mean unit cell parameters are a=4.76080±0.00029 Å, and c=12.99568 ű0.00087 Å (expanded uncertainty). These certified lattice parameters fall well within the results of those obtained from the international round-robin study. The Guinier-Hägg transmission measurements on five samples of powdered rubies (a=4.7610 ű0.0013 Å, and c = 12.9954 ű0.0034 Å) agreed well with the values obtained from the single crystal spheres. PMID:27500067

75 FR 30032 - Agency Information Collection Activities: Proposed Collection: Comment Request

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-28

... 66,951 0.5000 33,475.50 Kidney/Pancreas Candidate 143 14 2,002 0.5000 1,001.00 Registration Kidney/Pancreas Registration.... 143 7 1,001 0.9000 900.90 Kidney/Pancreas Follow-up....... 143 85 12,155 0.8500 10,331.75 Pancreas Candidate Registration. 143 7 1,001 0.5000 500.50 Pancreas Registration 143 3 429...

49 CFR Appendix A to Part 231 - Schedule of Civil Penalties 1

Code of Federal Regulations, 2010 CFR

2010-10-01

... or Hand Brake Parts Wrong Design 2,500 5,000 114.B2Hand Brake Wheel or Lever Has Insufficient Clearance Around Rim or Handle 2,500 5,000 114.B3Hand Brake Wheel/Lever Clearance Insufficient to Vertical... Improperly Applied 2,500 5,000 146.ANotice or Stencil not Posted on Cabooses with Running Boards Removed 650...

The SPACEHAB double module is moved into the payload changeout room at Launch Pad 39B

NASA Technical Reports Server (NTRS)

1999-01-01

This fish-eye view shows the SPACEHAB Double module being moved into the payload changeout room at Launch Pad 39B before being transferred to Space Shuttle Discovery's payload bay for mission STS-96. The second flight supporting construction of the International Space Station, STS-96 is a logistics and resupply mission, carrying more than 5,000 pounds of supplies, a Russian- built crane and a U.S.-built crane, plus experiments such as STARSHINE, which was developed by and for students. Comprising the crew are Commander Kent V. Rominger, Pilot Rick Douglas Husband, and Mission Specialists Ellen Ochoa (Ph.D.), Tamara E. Jernigan (Ph.D.), Daniel Barry (M.D., Ph.D.), Julie Payette, with the Canadian Space Agency, and Valery Ivanovich Tokarev, with the Russian Space Agency. Liftoff is scheduled for May 20 at 9:32 a.m. EDT.

A Standard Mammography Unit - Standard 3D Ultrasound Probe Fusion Prototype: First Results.

PubMed

Schulz-Wendtland, Rüdiger; Jud, Sebastian M; Fasching, Peter A; Hartmann, Arndt; Radicke, Marcus; Rauh, Claudia; Uder, Michael; Wunderle, Marius; Gass, Paul; Langemann, Hanna; Beckmann, Matthias W; Emons, Julius

2017-06-01

The combination of different imaging modalities through the use of fusion devices promises significant diagnostic improvement for breast pathology. The aim of this study was to evaluate image quality and clinical feasibility of a prototype fusion device (fusion prototype) constructed from a standard tomosynthesis mammography unit and a standard 3D ultrasound probe using a new method of breast compression. Imaging was performed on 5 mastectomy specimens from patients with confirmed DCIS or invasive carcinoma (BI-RADS ™ 6). For the preclinical fusion prototype an ABVS system ultrasound probe from an Acuson S2000 was integrated into a MAMMOMAT Inspiration (both Siemens Healthcare Ltd) and, with the aid of a newly developed compression plate, digital mammogram and automated 3D ultrasound images were obtained. The quality of digital mammogram images produced by the fusion prototype was comparable to those produced using conventional compression. The newly developed compression plate did not influence the applied x-ray dose. The method was not more labour intensive or time-consuming than conventional mammography. From the technical perspective, fusion of the two modalities was achievable. In this study, using only a few mastectomy specimens, the fusion of an automated 3D ultrasound machine with a standard mammography unit delivered images of comparable quality to conventional mammography. The device allows simultaneous ultrasound - the second important imaging modality in complementary breast diagnostics - without increasing examination time or requiring additional staff.

Application of a protocol for magnetic resonance spectroscopy of adrenal glands: an experiment with over 100 cases.

PubMed

Melo, Homero José de Farias E; Goldman, Suzan M; Szejnfeld, Jacob; Faria, Juliano F; Huayllas, Martha K P; Andreoni, Cássio; Kater, Cláudio E

2014-01-01

To evaluate a protocol for two-dimensional (2D) hydrogen proton (1H) magnetic resonance spectroscopy (MRS) (Siemens Medical Systems; Erlangen, Germany) in the detection of adrenal nodules and differentiation between benign and malignant masses (adenomas, pheochromocytomas, carcinomas and metastases). A total of 118 patients (36 men; 82 women) (mean age: 57.3 ± 13.3 years) presenting with 138 adrenal nodules/masses were prospectively assessed. A multivoxel system was utilized with a 2D point-resolved spectroscopy/chemical shift imaging sequence. The following ratios were calculated: choline (Cho)/creatine (Cr), 4.0-4.3/Cr, lipid (Lip)/Cr, Cho/Lip and lactate (Lac)/Cr. 2D-1H-MRS was successful in 123 (89.13%) lesions. Sensitivity and specificity values observed for the ratios and cutoff points were the following: Cho/Cr ≥ 1.2, 100% sensitivity, 98.2% specificity (differences between adenomas/pheochromocytomas and carcinomas/ metastases); 4.0-4.3 ppm/Cr ≥ 1.5, 92.3% sensitivity, 96.9% specificity (differences between carcinomas/pheochromocytomas and adenomas/metastases); Lac/Cr ≤ -7.449, 90.9% sensitivity and 77.8% specificity (differences between pheochromocytomas and carcinomas/adenomas). Information provided by 2D-1H-MRS were effective and allowed for the differentiation between adrenal masses and nodules in most cases of lesions with > 1.0 cm in diameter.

Dual-mode intracranial catheter integrating 3D ultrasound imaging and hyperthermia for neuro-oncology: feasibility study.

PubMed

Herickhoff, Carl D; Light, Edward D; Bing, Kristin F; Mukundan, Srinivasan; Grant, Gerald A; Wolf, Patrick D; Smith, Stephen W

2009-04-01

In this study, we investigated the feasibility of an intracranial catheter transducer with dual-mode capability of real-time 3D (RT3D) imaging and ultrasound hyperthermia, for application in the visualization and treatment of tumors in the brain. Feasibility is demonstrated in two ways: first by using a 50-element linear array transducer (17 mm x 3.1 mm aperture) operating at 4.4 MHz with our Volumetrics diagnostic scanner and custom, electrical impedance-matching circuits to achieve a temperature rise over 4 degrees C in excised pork muscle, and second, by designing and constructing a 12 Fr, integrated matrix and linear-array catheter transducer prototype for combined RT3D imaging and heating capability. This dual-mode catheter incorporated 153 matrix array elements and 11 linear array elements diced on a 0.2 mm pitch, with a total aperture size of 8.4 mm x 2.3 mm. This 3.64 MHz array achieved a 3.5 degrees C in vitro temperature rise at a 2 cm focal distance in tissue-mimicking material. The dual-mode catheter prototype was compared with a Siemens 10 Fr AcuNav catheter as a gold standard in experiments assessing image quality and therapeutic potential and both probes were used in an in vivo canine brain model to image anatomical structures and color Doppler blood flow and to attempt in vivo heating.

Dual-mode Intracranial Catheter Integrating 3D Ultrasound Imaging & Hyperthermia for Neuro-oncology: Feasibility Study

PubMed Central

Herickhoff, Carl D.; Light, Edward D.; Bing, Kristin F.; Mukundan, Srinivasan; Grant, Gerald A.; Wolf, Patrick D.; Smith, Stephen W.

2010-01-01

In this study, we investigated the feasibility of an intracranial catheter transducer with dual-mode capability of real-time 3D (RT3D) imaging and ultrasound hyperthermia, for application in the visualization and treatment of tumors in the brain. Feasibility is demonstrated in two ways: first by using a 50-element linear array transducer (17 mm × 3.1 mm aperture) operating at 4.4 MHz with our Volumetrics diagnostic scanner and custom electrical impedance matching circuits to achieve a temperature rise over 4°C in excised pork muscle, and second by designing and constructing a 12 Fr, integrated matrix and linear array catheter transducer prototype for combined RT3D imaging and heating capability. This dual-mode catheter incorporated 153 matrix array elements and 11 linear array elements diced on a 0.2 mm pitch, with a total aperture size of 8.4 mm × 2.3 mm. This array achieved a 3.5°C in vitro temperature rise at a 2 cm focal distance in tissue-mimicking material. The dual-mode catheter prototype was compared with a Siemens 10 Fr AcuNav™ catheter as a gold standard in experiments assessing image quality and therapeutic potential, and both probes were used in a canine brain model to image anatomical structures and color Doppler blood flow and to attempt in vivo heating. PMID:19630251

Macromolecular Calculations for the XTAL-System of Crystallographic Programs

DTIC Science & Technology

1990-05-24

C00 004 0 . . 0r004404- to 00 14fl 0. 41 4 zO 04 10-400D 000 0. 014 0 .- 4 14’-0 .41 I’D z qva to r. 1 4)0 0) 14 t .00. .. V’a00 0 R4 0 -4 H 4 14 014a0...Chemistry & Biochemistry 800 N. Quincy Street College Park, Maryland 20742 Arlington, Virginia 22217-5000 8a \\AE OF FLD,NG, 1 SPONSORING 8b OFFICE...Dr. Michael Marron 1 202-696-4760 1 ONR DO FORM 1473, P4 MAR 83 APR edition may be used until exhausted. SECURITY CLASSIFICATION OF THIS PAGE All

Borohydride Catalysis of Nitramine Thermal Decomposition and Combustion. 3. Literature Review and Wrap-Up Discussion of Possible Chemical Mechanisms

DTIC Science & Technology

1990-07-01

effect is quite well-known, and h s2 ble the subject of several workshops and cf a large number of reports. I2I The purpose of the present work is to...Their formation was rationalized in terms of the following mechanism: CF2 (N02) 2 + BH4 C--- F2 (N02) 2 D H+ +BH 3 0._• CPzNO 2 +NO 2 0 CF .2 (NO2...13 D. Mann G.B. Wilmot , R-16 R. Singleton Silver Spring, MD 20903-5000 R. Shaw P.O. Box 12211 5 Commander Research Triangle Park, NC Naval Research

Real-time three dimensional CT and MRI to guide interventions for congenital heart disease and acquired pulmonary vein stenosis.

PubMed

Suntharos, Patcharapong; Setser, Randolph M; Bradley-Skelton, Sharon; Prieto, Lourdes R

2017-10-01

To validate the feasibility and spatial accuracy of pre-procedural 3D images to 3D rotational fluoroscopy registration to guide interventional procedures in patients with congenital heart disease and acquired pulmonary vein stenosis. Cardiac interventions in patients with congenital and structural heart disease require complex catheter manipulation. Current technology allows registration of the anatomy obtained from 3D CT and/or MRI to be overlaid onto fluoroscopy. Thirty patients scheduled for interventional procedures from 12/2012 to 8/2015 were prospectively recruited. A C-arm CT using a biplane C-arm system (Artis zee, VC14H, Siemens Healthcare) was acquired to enable 3D3D registration with pre-procedural images. Following successful image fusion, the anatomic landmarks marked in pre-procedural images were overlaid on live fluoroscopy. The accuracy of image registration was determined by measuring the distance between overlay markers and a reference point in the image. The clinical utility of the registration was evaluated as either "High", "Medium" or "None". Seventeen patients with congenital heart disease and 13 with acquired pulmonary vein stenosis were enrolled. Accuracy and benefit of registration were not evaluated in two patients due to suboptimal images. The distance between the marker and the actual anatomical location was 0-2 mm in 18 (64%), 2-4 mm in 3 (11%) and >4 mm in 7 (25%) patients. 3D3D registration was highly beneficial in 18 (64%), intermediate in 3 (11%), and not beneficial in 7 (25%) patients. 3D3D registration can facilitate complex congenital and structural interventions. It may reduce procedure time, radiation and contrast dose.

Winds of Change: The Future of the 32D Army Air Defense Command in U.S. Army Europe

DTIC Science & Technology

1990-04-25

EDITION OF INOV S IS. OBSOLETE SECURITY CLASSIFICATION OF THIS PA.E e’Whe, Pate Fntrrpd) * A SECURITY CLASSIFICATION OF THIS PAGE(’Wlho Dal Entamd...Czechoslovakia and Poland have all announced reductions in their defenses and a reorientation of forces to a national defense role. In addition, these...5,000 tanks (later increased to 5,300 tanks and to include Poland ); *Reduce Soviet forces in Eastern Europe and Western Soviet Union by 10,000 tanks

Proceedings of the Environmental Research and Development (R&D) technical Workshop Held in San Diego, California on 7-9 November 1989

DTIC Science & Technology

1990-06-01

Released by Under authority of P. F. Seligman , Head S. Yamamoto, Head Marine Environment Branch Environmental Sciences Division NOTE: The front cover...168 ENVIRONMENT Peter F. Seligman Code 522, NOSC San Diego, CA 92152-5000 AUTOVON 553-2778, (619) 553-2778 IL 99 DEVELOPMENT OF INNOVATIVE...hour monitoring tests. The suggested ad- ditions will be implemented in version 3.9 as funding permits. REFERENCES 1. Clavell, C., Seligman , P. F, and

A Review and Analysis of Upgrades to Naval and Air Force Aircraft to Identify Similarities and Trends from Fiscal Year 1998 to 2013

DTIC Science & Technology

2013-06-01

AUTHOR( S ) Christopher Sylvester 7. PERFORMING ORGANIZATION NAME( S ) AND ADDRESS(ES) Naval Postgraduate School Monterey, CA 93943-5000 8...PERFORMING ORGANIZATION REPORT NUMBER 9. SPONSORING /MONITORING AGENCY NAME( S ) AND ADDRESS(ES) N/A 10. SPONSORING/MONITORING AGENCY REPORT NUMBER...Authorization Act ( S . 2515), which called upon the DoD to detail how it planned to ensure incorporation of EA. A year later, H.R. 1588 (National Defense

AFOSR Contractors Meeting on Propulsion, 15-19 Jun 1992

DTIC Science & Technology

1992-07-07

Ryan, H. M., Pal, S., Merkle , C. L., Jacobs, H. R. and Santoro, R. J., "Pressure Oscillation Effects on Jet Breakup," in Heat and Mass Transfer in Spray...Humboldt Court Edwards AFB CA 93523-5000 Sunnyvale CA 94086 (805)275-5540 (408)734-1622 AV525-5540 Dr Carl Melius Dr Charles Merkle Sandia National...State University Center for Chemical Engrg Blacksburg VA 24061 Gaithersburg MD 20899 (703)231-5950 Dr R G Rehm Dr Rolf D Reitz National Institute of

Maintenance of Paraoxonase 2 Activity as a Strategy to Attenuate P. Aeruginosa Virulence

DTIC Science & Technology

2013-10-01

identify the putative PON2 interacting protein, our approach is to IP the ~300kD BS3 crosslinked complex with a GFP antibody , run the IP on an SDS-PAGE...Dianova) were used at 1:5000. HRP- conjugated secondary antibodies were from Cell Signaling. Stealth-PON2 and control siRNAs (Invitrogen) sequences and...the lactonase paraoxonase 2 (PON2) and induces many immunomodulatory effects in host cells. Because PON2 rapidly inactivates 3OC12, we hypothesized

Metropolitan Spokane Region Water Resources Study. Appendix G. Planning Criteria

DTIC Science & Technology

1976-01-01

head or more of dairy cattle c. 2500 swine over 55 pounds d. 10,000 head of sheep e. 55,000 turkeys f. 100,000 laying hens or broilers g. 30,000 laying...hens or broilers with liquid manure handling systems h. 5000 ducks i. combinations of animals per schedule 317-20 IM 2. Fish production facilities. a...previously stabilized by the equivalent of anaerobic digestion . 2. Lhere public access is not positively controlled, pathogen re- duction beyond that

Studies of Near-Source and Near-Receiver Scattering and Low-Frequency Lg from East Kazakh and NTS Explosions

DTIC Science & Technology

1991-12-04

ADDRESS(ES) 10. SPONSORING/MONITORING DARPA/NMRO Phillips Laboratory AGENCY REPORT NUMBER (Attn: Dr. A. Ryall) Hanscom AFB, MA 01731-5000 3701 North...areas and media at the USERDA Nevada Test Site, UCRL -51948, Lawrence Livermore La- boratory, Livermore, California. Stead, R. J. and D. V. HeImberger...University Park, PA 16802 Blacksburg, VA 24061 Dr. Ralph Alewine, III Dr. Stephen Bratt DARPA/NMRO Center for Seismic Studies 3701 North Fairfax Drive 1300

Proceedings of the Annual PL/DARPA Seismic Research Symposium (14th) Held in Tucson, AZ on 16-18 September 1992

DTIC Science & Technology

1992-08-17

01731-5000 UP, No. 1106 9. SPONSORING / MONITORING AGENCY NAME(S) AND ADDRESS(ES) 10. SPONSORING/ MONITORING AGENCY REPORT NUMBER DARPA/NMRO 3701 North...the peaceful uses of nuclear explosives, UCRL -5414, Lawrence Livermore National Laboratory, 1973. Nordyke, M.D., A review of Soviet data on the peaceful...Lawrence Livermore national Laboratory, UCRL -JC-107941, preprint. Haskell, N. A. (1964). Radiation pattern of surface waves from point sources in a

Charge composition of high energy heavy primary cosmic ray nuclei. Ph.D. Thesis - Catholic Univ. of Am.

NASA Technical Reports Server (NTRS)

Price, R. D.

1974-01-01

A detailed study of the charge composition of primary cosmic radiation for about 5000 charged nuclei from neon to iron with energies greater than 1.16 GeV/nucleon is presented. Values are obtained after corrections were made for detector dependences, atmospheric attenuation, and solar modulation. New values of 38.5, 32.4, 23.7, and 16.8 g/sq cm for the attenuation mean free paths in air for the same charge groups are presented.

A Department of Homeland Security Reserves (DHS-R): Simultaneously Protecting the Homeland While Alleviating the Increased DoD Role in Homeland Defense and Security

DTIC Science & Technology

2007-12-01

and Security 6. AUTHOR( S ) David V. Schulz 5. FUNDING NUMBERS 7. PERFORMING ORGANIZATION NAME( S ) AND ADDRESS(ES) Naval Postgraduate School...Monterey, CA 93943-5000 8. PERFORMING ORGANIZATION REPORT NUMBER 9. SPONSORING /MONITORING AGENCY NAME( S ) AND ADDRESS(ES) N/A 10. SPONSORING...responding agencies. In fact, the slow Katrina response was attributed to “coordination difficulties” between the military, law enforcement, and

Electrical Microengineering of Redox Enzymes

DTIC Science & Technology

1994-03-31

coating applied to the electrode 41 to prevent lose of mediator graphite foil potassium -~0.02a 0.03  electrolyte wus dioxane with 15% 42...hexacyanoferrats(ll)d aqueous buffer carbon fiber’ none h 40-5000 biotin/avidin complex used to obtain a 43 surface layer of HRP Pt organic metal, potassium ...OFFICE OF NAVAL RESEARCH AD-A279 015 FINAL REPORT FOR CONTRACT NOOO 14-91 -J- 1656 R&T CODE 413h007---05 ELECTRICAL MICROENGINEERING OF REDOX ENZYMES

On the Importance of Displacement History in Soft-Body Contact Models

DTIC Science & Technology

2015-07-10

Plimpton , S . J., 2001. “Granular flow down an inclined plane: Bagnold scaling and rheol- ogy”. Physical Review E, 64(5), p. 051302. [16] Zhang, H. P...Models 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR( S ) 5d. PROJECT NUMBER 5e. TASK NUMBER 5f. WORK UNIT NUMBER 7...PERFORMING ORGANIZATION NAME( S ) AND ADDRESS(ES) US Army RDECOM-TARDEC,6501 E. 11 Mile Road,Warren,MI,48397-5000 8. PERFORMING ORGANIZATION REPORT

[The Patau syndrome].

PubMed

Misanović, Verica; Jonuzi, Fedat; Biscević, Emir; Uzicanin, Sajra; Vegar, Sandra

2002-01-01

Known as D trisomy, Patau syndrome is the third chromosomopathy according to frequency. One of the 5000 newborn carries the trisomy 13. In over 80% cases there is fresh mutation with non separation in myeosis of older mother. The mosaic or translocation forms are not rare. The mail newborn with Patau syndrome is shown in this article. We notice: microcephalia, dolihocephalia, microphthalmia, cheilognatopalatoshisis, polydactilia, and found ultrasound changes at the brain, hearth and genitourinary system. Cytogenetic finding show: mail cariotype with aberrations 47, XY + 13, Sy Patau.

DOD Contractor Collaborations: Proposed Procedures for Integrating Antitrust Law, Procurement Law, and Purchasing Decisions

DTIC Science & Technology

2001-04-01

conducted at the initial stages of program definition. DoD 5000.2-R, supra note 2, at para. 2.3.1. For "commercial activities" conversion studies , market...by the post- facto nature of the Competition Advocacy program. This program generally requires setting of competition goals, measurement of goal...expanded coverage of the False Claims Act and expost review of prices.344 Contracting officers can inject a degree of prospective management oversight of

Ultra-compact channel drop filter based on photonic crystal nanobeam cavities utilizing a resonant tunneling effect.

PubMed

Ge, Xiaochen; Shi, Yaocheng; He, Sailing

2014-12-15

The design, fabrication, and characterization of a compact photonic crystal nanobeam drop filter based on the tunneling effect of the degenerate modes are presented. The degeneracy was achieved by tuning the coupling distance between the nanobeam and input/output waveguides. The tunneling effect of degenerate resonances with different symmetries has been verified experimentally. Channel drop filters with an extinction ratio larger than 10 dB and a quality factor of ∼5000 have been experimentally demonstrated.

Effects of Physical Impairment on Grenade Throwing and Weapon Loading Tasks

DTIC Science & Technology

2015-03-01

1 GOVT PRINTG OFC (PDF) A MALHOTRA 1 ARMY RSCH LABORATORY – HRED (PDF) RDRL HRM D T DAVIS BLDG 5400 RM C242 REDSTONE ARSENAL...5002 1 ARMY RSCH LABORATORY – HRED (PDF) RDRL HRM DG J RUBINSTEIN BLDG 333 PICATINNY ARSENAL NJ 07806-5000 1 ARMY RSCH LABORATORY...HRED (PDF) ARMC FIELD ELEMENT RDRL HRM CH C BURNS THIRD AVE BLDG 1467B RM 336 FORT KNOX KY 40121 1 ARMY RSCH LABORATORY – HRED

Real-time Awake Animal Motion Tracking System for SPECT Imaging

DOE Office of Scientific and Technical Information (OSTI.GOV)

Goddard Jr, James Samuel; Baba, Justin S; Lee, Seung Joon

Enhancements have been made in the development of a real-time optical pose measurement and tracking system that provides 3D position and orientation data for a single photon emission computed tomography (SPECT) imaging system for awake, unanesthetized, unrestrained small animals. Three optical cameras with infrared (IR) illumination view the head movements of an animal enclosed in a transparent burrow. Markers placed on the head provide landmark points for image segmentation. Strobed IR LED s are synchronized to the cameras and illuminate the markers to prevent motion blur for each set of images. The system using the three cameras automatically segments themore » markers, detects missing data, rejects false reflections, performs trinocular marker correspondence, and calculates the 3D pose of the animal s head. Improvements have been made in methods for segmentation, tracking, and 3D calculation to give higher speed and more accurate measurements during a scan. The optical hardware has been installed within a Siemens MicroCAT II small animal scanner at Johns Hopkins without requiring functional changes to the scanner operation. The system has undergone testing using both phantoms and live mice and has been characterized in terms of speed, accuracy, robustness, and reliability. Experimental data showing these motion tracking results are given.« less

Three-dimensional contrast-enhanced magnetic resonance angiography for anterolateral thigh flap outlining: A retrospective case series of 68 patients.

PubMed

Jiang, Chunjing; Lin, Ping; Fu, Xiaoyan; Shu, Jiner; Li, Huimin; Hu, Xiaogang; He, Jianrong; Ding, Mingxing

2016-08-01

Flap transfer is increasingly used for repairing limb defects secondary to trauma or tumor, and appropriate preoperative planning plays a critical role. The present study aimed to examine the use of three-dimensional (3D) contrast-enhanced magnetic resonance angiography (CE-MRA) in evaluating the blood supply distribution and perforating branch pattern of anterolateral thigh (ALT) flaps. Bilateral donor lower limbs were scanned in 68 patients (136 limbs) using a Siemens Avanto 1.5 T magnetic resonance imaging scanner with a 3D fast low-angle shot sequence, following the thin-slab maximum intensity projection (TS-MIP) technique. The lateral femoral circumflex artery (LFCA) was visualized in all patients: 101 limbs (101/136, 74.3%) were type I; 20 limbs (20/136, 14.7%) were type II; 3 limbs (3/136, 2.2%) were type III; and 12 limbs (12/136, 8.8%) were type IV. Tertiary branches were identified in 94 limbs (94/136, 69.1%). Donor flaps were outlined according to MRA TS-MIP findings in 4 patients. All flaps survived uneventfully following the transfer. In donor flap outlining, 3D CE-MRA with the TS-MIP technique allowed an accurate, direct visualization of the branching pattern and distribution profile of the LFCA supplying the ALT flap.

Acute toxicity and cytotoxicity evaluation of Dendrobium moniliforme aqueous extract in vivo and in vitro

PubMed Central

Lee, Mu-Jin; Jung, Ho-Kyung; Kim, Min-Suk; Jang, Ji-Hun; Sim, Mi-Ok; Kim, Tea-Mook; Park, Ho; Ahn, Byung-Kwan; Cho, Hyun-Woo; Cho, Jung-Hee

2016-01-01

Dendrobium moniliforme (L.) Sw., an herb of the Orchidaceae family, has long been used in traditional medicine to strengthen bones, nourish the stomach, and promote the production of bodily fluid. Recently, polysaccharides isolated from Dendrobium have been used in functional foods and nutraceutical products. A traditional method to process Dendrobium is to soak fresh stems in an ethanol solution, which is the most important factor to ensure high yields of aqueous-extractable polysaccharides. The present study was carried out to investigate the potential acute toxicity of D. moniliforme aqueous extract (DMAE), by a single oral dose in Sprague-Dawley rats. The test article was orally administered once by gavage to male and female rats at doses of 0, 2,500, and 5,000 mg/kg body weight (n=5 male and female rats for each dose). Throughout the study period, no treatment-related deaths were observed and no adverse effects were noted in clinical signs, body weight, food consumption, serum biochemistry, organ weight, or gross findings at any dose tested. The results show that a single oral administration of DMAE did not induce any toxic effects at a dose below 5,000 mg/kg in rats, and the minimal lethal dose was considered to be over 5,000 mg/kg body weight for both sexes. With respect to cytotoxicity, the cell viability of human embryonic kidney (HEK293) cells was less than 50% when the cells were treated with 10 mg/mL aqueous extract for 24 h. PMID:27729930

Innovation Concepts in Healthcare

ScienceCinema

Requardt, Hermann

2017-12-18

Demographic change and advances in medical science pose increased challenges to healthcare systems globally: The economic basis is aging and thus health is becoming more and more a productivity factor. At the same time, with today’s new communication possibilities the demand and expectations of effective medical treatment have been increased. This presentation will illustrate the need for the “industrialization” of healthcare in order to achieve highest results at limited budgets. Thereby, industrialization is not meaning the medical treatment based on the assembly line approach. Rather it is to recognize the cost of medical care as an investment with respective expectations on the return of the investment. Innovations in imaging and pharmaceutical products as well as in processes - that lead to similar medical results, but with lower efforts - are keys in such scenarios. Biography Prof. Dr. Hermann Requardt, 54, is a member of the Managing Board of Siemens AG and Chief Executive Officer of the Healthcare Sector. In addition he is the CTO of Siemens AG and Head of Corporate Technology, the central research department at Siemens. After completing his studies in physics and philosophy at the Darmstadt University of Technology and Johann Wolfgang Goethe University in Frankfurt and receiving a doctorate in biophysics, he worked at the Institute of Aerospace Medicine at the German Aerospace Center.In 1984 he joined the Medical Technology Group of Siemens AG, where he was responsible for projects in the Magnetic Resonance (MR) division. He was appointed head of the division in 1995. From 2001 to 2006, as a member of the Executive Management of the Medical Solutions Group, he was responsible for several areas, including technological development.In 2006 he became a Member of the Siemens’ Managing Board and head of Corporate Technology. He was additionally appointed as the Sector Healthcare CEO in 2008.Since 2006 he is an honorary professor in physics of the Johann Wolfgang Goethe University in Frankfurt.                                                                                

49 CFR Appendix A to Part 238 - Schedule of Civil Penalties 1

Code of Federal Regulations, 2014 CFR

2014-10-01

....15Movement of power brake defects: (b) Improper movement from Class I or IA brake test 5,000 7,500 (c... required design features 5,000 7,500 (e) Failure to comply with hardware and software safety program 5,000... test previously used equipment 7,500 11,000 (b)(1) Failure to develop plan 7,500 11,000 (b)(2) Failure...