Science.gov

Sample records for silica photonic crystal

  1. Mid-infrared supercontinuum generation in silica photonic crystal fibers.

    PubMed

    Bi, Wanjun; Gao, Juanjuan; Li, Xia; Xiong, Liangming; Liao, Meisong

    2016-08-10

    A mid-infrared supercontinuum (SC) light source, which has important applications in many fields, has been extensively investigated in soft glass fibers. However, the poor instinct properties of soft glass fibers and the development of ultrashort pulse lasers left an opportunity for mid-infrared SC generation in silica fiber. Until now, silica fiber has been the commonly used medium for SC generation due to its outstanding properties. In this paper, mid-infrared SC generation in short silica photonic crystal fibers (PCFs) is investigated theoretically and systematically. In the case of a 1550�nm pump, the soliton self-frequency shift effect is utilized to extend the long wavelength edge of SC. Adopting a fiber that has a zero dispersion wavelength away from the pump pulse is a benefit for the suppression of blue spectral component and energy distribution in the long wavelength band. In the case of a 1950�nm pump, the generation of a red-shifted dispersive wave is an efficient way to extend the long wavelength edge of SC. Additionally, the coherence for femtosecond pulse pumping is discussed in this paper. Finally, the long wavelength edge of SC is beyond 3000�nm when a 1950�nm femtosecond pump pulse propagates in a PCF with negative dispersive slope around the pump pulse. PMID:27534479

  2. Thermally Driven Photonic Actuator Based on Silica Opal Photonic Crystal with Liquid Crystal Elastomer.

    PubMed

    Xing, Huihui; Li, Jun; Shi, Yang; Guo, Jinbao; Wei, Jie

    2016-04-13

    We have developed a novel thermoresponsive photonic actuator based on three-dimensional SiO2 opal photonic crystals (PCs) together with liquid crystal elastomers (LCEs). In the process of fabrication of such a photonic actuator, the LCE precursor is infiltrated into the SiO2 opal PC followed by UV light-induced photopolymerization, thereby forming the SiO2 opal PC/LCE composite film with a bilayer structure. We find that this bilayer composite film simultaneously exhibits actuation behavior as well as the photonic band gap (PBG) response to external temperature variation. When the SiO2 opal PC/LCE composite film is heated, it exhibits a considerable bending deformation, and its PBG shifts to a shorter wavelength at the same time. In addition, this actuation is quite fast, reversible, and highly repeatable. The thermoresponsive behavior of the SiO2 opal PC/LCE composite films mainly derives from the thermal-driven change of nematic order of the LCE layer which leads to the asymmetric shrinkage/expansion of the bilayer structure. These results will be of interest in designing optical actuator systems for environment-temperature detection. PMID:26996608

  3. Thermally Driven Photonic Actuator Based on Silica Opal Photonic Crystal with Liquid Crystal Elastomer.

    PubMed

    Xing, Huihui; Li, Jun; Shi, Yang; Guo, Jinbao; Wei, Jie

    2016-04-13

    We have developed a novel thermoresponsive photonic actuator based on three-dimensional SiO2 opal photonic crystals (PCs) together with liquid crystal elastomers (LCEs). In the process of fabrication of such a photonic actuator, the LCE precursor is infiltrated into the SiO2 opal PC followed by UV light-induced photopolymerization, thereby forming the SiO2 opal PC/LCE composite film with a bilayer structure. We find that this bilayer composite film simultaneously exhibits actuation behavior as well as the photonic band gap (PBG) response to external temperature variation. When the SiO2 opal PC/LCE composite film is heated, it exhibits a considerable bending deformation, and its PBG shifts to a shorter wavelength at the same time. In addition, this actuation is quite fast, reversible, and highly repeatable. The thermoresponsive behavior of the SiO2 opal PC/LCE composite films mainly derives from the thermal-driven change of nematic order of the LCE layer which leads to the asymmetric shrinkage/expansion of the bilayer structure. These results will be of interest in designing optical actuator systems for environment-temperature detection.

  4. A comparative study of inverted-opal titania photonic crystals made from polymer and silica colloidal crystal templates

    SciTech Connect

    Kuai, S.-L.; Truong, V.-V.; Hache, Alain; Hu, X.-F.

    2004-12-01

    Photonic crystals with an inverted-opal structure using polymer and silica colloidal crystal templates were prepared and compared. We show that the behaviors of the template during the removal process and heat treatment are determinant factors on the crystal formation. While both templates result in ordered macroporous structures, the optical quality in each case is quite different. The removal of the polymer template by sintering causes a large shrinkage of the inverted framework and produces a high density of cracks in the sample. With a silica template, sintering actually improves the quality of the inverted structure by enhancing the template's mechanical stability, helping increase the filling fraction, and consolidating the titania framework. The role of the other important factors such as preheating and multiple infiltrations is also investigated.

  5. Spontaneous and stimulated Raman scattering in silica-cladded silicon photonic crystal waveguides

    NASA Astrophysics Data System (ADS)

    Hsiao, Yi-Hua; Iwamoto, Satoshi; Arakawa, Yasuhiko

    2015-04-01

    We report the observation of spontaneous and stimulated Raman scattering in a silica-cladded silicon photonic crystal (PhC) waveguide (WG) with modified holes. Spontaneous Raman scattering in the WG was enhanced when the Stokes wavelength was approached to the bandedge of a WG mode. A maximum enhancement up to ˜5 times was obtained in the present work. At a Stokes wavelength in the lower group velocity region, nonlinear increase of the Stokes power as the pump power, a clear indication of the onset of stimulated Raman scattering, was observed. Moreover, Raman amplification with an external signal beam was also demonstrated. On-off gain becomes small as the Stokes wavelength gets away from the bandedge of the WG mode. These are the first observations of Raman scattering effects in silica-cladded silicon PhC structures.

  6. Fabrication of silica hollow core photonic crystal fibres for Er:YAG surgical applications

    NASA Astrophysics Data System (ADS)

    Urich, Artur; Maier, Robert R. J.; Knight, Jonathan C.; Mangan, Brian J.; Renshaw, Steven; Hand, Duncan P.; Shephard, Jonathan D.

    2012-01-01

    In this work we present the fabrication of silica hollow core photonic crystal fibres (HC-PCF) with guidance at 2.94μm. As light is confined inside the hollow core with a very small overlap of the guided E-M wave with the fibre material, the high intrinsic loss of silica at these mid-infrared wavelengths can be overcome. The band gap effect is achieved by a periodic structure made out of air and fused silica. As silica is bio-inert, chemically stable and mechanically robust, these fibres have potential advantages over other multi-component, non-silica optical fibres designed to guide in this wavelength regime. These fibres have a relatively small diameter, low bend sensitivity and single-mode like guidance which are ideal conditions for delivering laser light down a highly flexible fibre. Consequently they provide a potential alternative to existing surgical laser delivery methods such as articulated arms and lend themselves to endoscopy and other minimally invasive surgical procedures. In particular, we present the characterisation and performance of these fibres at 2.94 μm, the wavelength of an Er:YAG laser. This laser is widely used in surgery since the wavelength overlaps with an absorption band of water which results in clean, non-cauterised cuts. However, the practical implementation of these types of fibres for surgical applications is a significant challenge. Therefore we also report on progress made in developing hermetically sealed end tips for these hollow core fibres to avoid contamination. This work ultimately prepares the route towards a robust, practical delivery system for this wavelength.

  7. Monodisperse spherical mesoporous silica particles: fast synthesis procedure and fabrication of photonic-crystal films

    NASA Astrophysics Data System (ADS)

    Trofimova, E. Yu; Kurdyukov, D. A.; Yakovlev, S. A.; Kirilenko, D. A.; Kukushkina, Yu A.; Nashchekin, A. V.; Sitnikova, A. A.; Yagovkina, M. A.; Golubev, V. G.

    2013-04-01

    A procedure for the synthesis of monodisperse spherical mesoporous silica particles (MSMSPs) via the controlled coagulation of silica/surfactant clusters into spherical aggregates with mean diameters of 250-1500 nm has been developed. The synthesis is fast (taking less than 1 h) because identical clusters are simultaneously formed in the reaction mixture. The results of microscopic, x-ray diffraction, adsorption and optical measurements allowed us to conclude that the clusters are ˜15 nm in size and have hexagonally packed cylindrical pore channels. The channel diameters in MSMSPs obtained with cethyltrimethylammonium bromide and decyltrimethylammonium bromide as structure-directing agents were 3.1 ± 0.15 and 2.3 ± 0.12 nm, respectively. The specific surface area and the pore volume of MSMSP were, depending on synthesis conditions, 480-1095 m2 g-1 and 0.50-0.65 cm3 g-1. The MSMSP were used to grow opal-like photonic-crystal films possessing a hierarchical macro-mesoporous structure, with pores within and between the particles. A selective filling of mesopore channels with glycerol, based on the difference between the capillary pressures in macro- and mesopores, was demonstrated. It is shown that this approach makes it possible to control the photonic bandgap position in mesoporous opal films by varying the degree of mesopore filling with glycerol.

  8. Thermoluminescence Response of Ge-Doped Cylindrical-, Flat- and Photonic Crystal Silica-Fibres to Electron and Photon Radiation.

    PubMed

    Entezam, A; Khandaker, M U; Amin, Y M; Ung, N M; Bradley, D A; Maah, J; Safari, M J; Moradi, F

    2016-01-01

    Study has been made of the thermoluminescence (TL) response of silica-based Ge-doped cylindrical, flat and photonic crystal fibres (referred to herein as PCF-collapsed) to electron (6, 12 and 20 MeV) and photon (6, 10 MV) irradiation and 1.25 MeV γ-rays, for doses from 0.1 Gy to 100 Gy. The electron and photon irradiations were delivered through use of a Varian Model 2100C linear accelerator located at the University of Malaya Medical Centre and γ-rays delivered from a 60Co irradiator located at the Secondary Standard Dosimetry Laboratory (SSDL), Malaysian Nuclear Agency. Tailor-made to be of various dimensions and dopant concentrations (6-10% Ge), the fibres were observed to provide TL yield linear with radiation dose, reproducibility being within 1-5%, with insensitivity to energy and angular variation. The sensitivity dependency of both detectors with respect to field size follows the dependency of the output factors. For flat fibres exposed to 6 MV X-rays, the 6% Ge-doped fibre provided the greatest TL yield while PCF-collapsed showed a response 2.4 times greater than that of the 6% Ge-doped flat fibres. The response of cylindrical fibres increased with core size. The fibres offer uniform response, high spatial resolution and sensitivity, providing the basis of promising TL systems for radiotherapy applications. PMID:27149115

  9. Thermoluminescence Response of Ge-Doped Cylindrical-, Flat- and Photonic Crystal Silica-Fibres to Electron and Photon Radiation

    PubMed Central

    Entezam, A.; Khandaker, M. U.; Amin, Y. M.; Ung, N. M.; Bradley, D. A.; Maah, J.; Safari, M. J.; Moradi, F.

    2016-01-01

    Study has been made of the thermoluminescence (TL) response of silica-based Ge-doped cylindrical, flat and photonic crystal fibres (referred to herein as PCF-collapsed) to electron (6, 12 and 20 MeV) and photon (6, 10 MV) irradiation and 1.25 MeV γ-rays, for doses from 0.1 Gy to 100 Gy. The electron and photon irradiations were delivered through use of a Varian Model 2100C linear accelerator located at the University of Malaya Medical Centre and γ-rays delivered from a 60Co irradiator located at the Secondary Standard Dosimetry Laboratory (SSDL), Malaysian Nuclear Agency. Tailor-made to be of various dimensions and dopant concentrations (6–10% Ge), the fibres were observed to provide TL yield linear with radiation dose, reproducibility being within 1–5%, with insensitivity to energy and angular variation. The sensitivity dependency of both detectors with respect to field size follows the dependency of the output factors. For flat fibres exposed to 6 MV X-rays, the 6% Ge-doped fibre provided the greatest TL yield while PCF-collapsed showed a response 2.4 times greater than that of the 6% Ge-doped flat fibres. The response of cylindrical fibres increased with core size. The fibres offer uniform response, high spatial resolution and sensitivity, providing the basis of promising TL systems for radiotherapy applications. PMID:27149115

  10. Thermoluminescence Response of Ge-Doped Cylindrical-, Flat- and Photonic Crystal Silica-Fibres to Electron and Photon Radiation.

    PubMed

    Entezam, A; Khandaker, M U; Amin, Y M; Ung, N M; Bradley, D A; Maah, J; Safari, M J; Moradi, F

    2016-01-01

    Study has been made of the thermoluminescence (TL) response of silica-based Ge-doped cylindrical, flat and photonic crystal fibres (referred to herein as PCF-collapsed) to electron (6, 12 and 20 MeV) and photon (6, 10 MV) irradiation and 1.25 MeV γ-rays, for doses from 0.1 Gy to 100 Gy. The electron and photon irradiations were delivered through use of a Varian Model 2100C linear accelerator located at the University of Malaya Medical Centre and γ-rays delivered from a 60Co irradiator located at the Secondary Standard Dosimetry Laboratory (SSDL), Malaysian Nuclear Agency. Tailor-made to be of various dimensions and dopant concentrations (6-10% Ge), the fibres were observed to provide TL yield linear with radiation dose, reproducibility being within 1-5%, with insensitivity to energy and angular variation. The sensitivity dependency of both detectors with respect to field size follows the dependency of the output factors. For flat fibres exposed to 6 MV X-rays, the 6% Ge-doped fibre provided the greatest TL yield while PCF-collapsed showed a response 2.4 times greater than that of the 6% Ge-doped flat fibres. The response of cylindrical fibres increased with core size. The fibres offer uniform response, high spatial resolution and sensitivity, providing the basis of promising TL systems for radiotherapy applications.

  11. The polarization modulation and fabrication method of two dimensional silica photonic crystals based on UV nanoimprint lithography and hot imprint

    PubMed Central

    Guo, Shuai; Niu, Chunhui; Liang, Liang; Chai, Ke; Jia, Yaqing; Zhao, Fangyin; Li, Ya; Zou, Bingsuo; Liu, Ruibin

    2016-01-01

    Based on a silica sol-gel technique, highly-structurally ordered silica photonic structures were fabricated by UV lithography and hot manual nanoimprint efforts, which makes large-scale fabrication of silica photonic crystals easy and results in low-cost. These photonic structures show perfect periodicity, smooth and flat surfaces and consistent aspect ratios, which are checked by scanning electron microscopy (SEM) and atomic force microscopy (AFM). In addition, glass substrates with imprinted photonic nanostructures show good diffraction performance in both transmission and reflection mode. Furthermore, the reflection efficiency can be enhanced by 5 nm Au nanoparticle coating, which does not affect the original imprint structure. Also the refractive index and dielectric constant of the imprinted silica is close to that of the dielectric layer in nanodevices. In addition, the polarization characteristics of the reflected light can be modulated by stripe nanostructures through changing the incident light angle. The experimental findings match with theoretical results, making silica photonic nanostructures functional integration layers in many optical or optoelectronic devices, such as LED and microlasers to enhance the optical performance and modulate polarization properties in an economical and large-scale way. PMID:27698465

  12. The polarization modulation and fabrication method of two dimensional silica photonic crystals based on UV nanoimprint lithography and hot imprint

    NASA Astrophysics Data System (ADS)

    Guo, Shuai; Niu, Chunhui; Liang, Liang; Chai, Ke; Jia, Yaqing; Zhao, Fangyin; Li, Ya; Zou, Bingsuo; Liu, Ruibin

    2016-10-01

    Based on a silica sol-gel technique, highly-structurally ordered silica photonic structures were fabricated by UV lithography and hot manual nanoimprint efforts, which makes large-scale fabrication of silica photonic crystals easy and results in low-cost. These photonic structures show perfect periodicity, smooth and flat surfaces and consistent aspect ratios, which are checked by scanning electron microscopy (SEM) and atomic force microscopy (AFM). In addition, glass substrates with imprinted photonic nanostructures show good diffraction performance in both transmission and reflection mode. Furthermore, the reflection efficiency can be enhanced by 5 nm Au nanoparticle coating, which does not affect the original imprint structure. Also the refractive index and dielectric constant of the imprinted silica is close to that of the dielectric layer in nanodevices. In addition, the polarization characteristics of the reflected light can be modulated by stripe nanostructures through changing the incident light angle. The experimental findings match with theoretical results, making silica photonic nanostructures functional integration layers in many optical or optoelectronic devices, such as LED and microlasers to enhance the optical performance and modulate polarization properties in an economical and large-scale way.

  13. Photoinduced local heating in silica photonic crystals for fast and reversible switching.

    PubMed

    Gallego-Gómez, Francisco; Blanco, Alvaro; López, Cefe

    2012-12-01

    Fast and reversible photonic-bandgap tunability is achieved in silica artificial opals by local heating. The effect is fully reversible as heat rapidly dissipates through the non-irradiated structure without active cooling and water is readsorbed. The performance is strongly enhanced by decreasing the photoirradiated opal volume, allowing bandgap shifts of 12 nm and response times of 20 ms. PMID:22976241

  14. Experimental study of photonic crystal triangular lattices

    NASA Astrophysics Data System (ADS)

    Qin, Ruhu; Qin, Bo; Jin, Chongjun

    1999-06-01

    Triangular lattice photonic crystal behaving in the electromagnetic zones constructed from fused silica cylinders in styrofoam is fabricated. The transmission spectra of the photonic crystal with and without defects are measured. On this basis, the defect modes of photonic crystal were studied, and the potential applications of the photonic crystal are discussed.

  15. Experimental studies of cobalt ferrite nanoparticles doped silica matrix 3D magneto-photonic crystals

    NASA Astrophysics Data System (ADS)

    Abou Diwan, E.; Royer, F.; Kekesi, R.; Jamon, D.; Blanc-Mignon, M. F.; Neveu, S.; Rousseau, J. J.

    2013-05-01

    In this paper, we present the synthesis and the optical properties of 3D magneto-photonic structures. The elaboration process consists in firstly preparing then infiltrating polystyrene direct opals with a homogeneous solution of sol-gel silica precursors doped by cobalt ferrite nanoparticles, and finally dissolving the polystyrene spheres. Scanning Electron Microscopy (SEM) images of the prepared samples clearly evidence a periodic arrangement. Using a home-made polarimetric optical bench, the transmittance as a function of the wavelength, the Faraday rotation as a function of the applied magnetic field, and the Faraday ellipticity as a function of the wavelength and as a function of the applied magnetic field were measured. The existence of deep photonic band gaps (PBG), the unambiguous magnetic character of the samples and the qualitative modification of the Faraday ellipticity in the area of the PBG are evidenced.

  16. Octave-spanning spectrum generation in tapered silica photonic crystal fiber by Yb:fiber ring laser above 500 MHz.

    PubMed

    Jiang, Tongxiao; Wang, Guizhong; Zhang, Wei; Li, Chen; Wang, Aimin; Zhang, Zhigang

    2013-02-15

    We report octave-spanning spectrum generated in a tapered silica photonic crystal fiber by a mode-locked Yb:fiber ring laser at a repetition rate as high as 528 MHz. The output pulses from this laser were compressed to 62 fs. By controlling the hole expansion and core diameter, a silica PCF was tapered to 20 cm with an optimal d/Λ ratio of 0.6. Pulses with the energy of 280 pJ and the peak power of 4.5 kW were injected into the tapered fiber and the pulse spectrum was expanded from 500 to 1600 nm at the level of -30 dB.

  17. Effect of size of silica microspheres on photonic band gap

    SciTech Connect

    Dhiman, N. Sharma, A. Gathania, A. K.; Singh, B. P.

    2014-04-24

    In present work photonic crystals of different size of silica microspheres have been fabricated. The optical properties of these developed photonic crystals have been studied using UV-visible spectroscopy. UV-visible spectroscopy shows that they have photonic band gap that can be tuned in visible and infrared regime by changing the size of silica microspheres. The photonic band gap structures of these photonic crystals have been calculated using MIT photonic band gap package. It also reveals that with the increase in size of silica microspheres the photonic band gap shifts to lower energy region.

  18. Polarization diversity circuit for a silicon optical switch using silica waveguides integrated with photonic crystal thin film waveplates

    NASA Astrophysics Data System (ADS)

    Sugiyama, Koki; Chiba, Takafumi; Kawashima, Takayuki; Kawakami, Shojiro; Takahashi, Hiroshi; Tsuda, Hiroyuki

    2016-03-01

    We propose a compact polarization diversity optical circuit using silica waveguides and photonic crystal waveplates. By setting these circuits at the front and rear of the silicon optical devices, the polarization dependence of the silicon devices can be suppressed. Photonic crystals can be produced artificially using nanolithography, so that the retardation and orientation of the photonic crystal waveplate can be locally varied on a single chip. This enables to dramatically reduce the size of the polarization diversity circuit, which consists of a 1x2 multimode interference (MMI) coupler, two arm waveguides with quarter-waveplates (QWPs), a 2x2 MMI coupler, and output waveguides with half-waveplates (HWPs). The input light, including the transverse electric (TE) and transverse magnetic (TM) modes, is split by the 1x2 MMI coupler. The optical axes of the two QWPs, spaced 125 μm apart, are set to be orthogonal to each other, so that the phases of the TE modes in the two arm waveguides differ by 90 degrees, and those of the TM modes differ by -90 degrees. The TE mode and the TM mode are separated at the outputs of the 2x2 MMI coupler, and the polarization of the light at one of the outputs is aligned to that at the other output by the HWP. In this paper, we designed a 4x8 polarization diversity circuit for a 4x4 silicon optical switch.

  19. Delivery of high energy Er:YAG pulsed laser light at 2.94 µm through a silica hollow core photonic crystal fibre.

    PubMed

    Urich, A; Maier, R R J; Mangan, B J; Renshaw, S; Knight, J C; Hand, D P; Shephard, J D

    2012-03-12

    In this paper the delivery of high power Er:YAG laser pulses through a silica hollow core photonic crystal fibre is demonstrated. The Er:YAG wavelength of 2.94 µm is well beyond the normal transmittance of bulk silica but the unique hollow core guidance allows silica to guide in this regime. We have demonstrated for the first time the ability to deliver high energy pulses through an all-silica fibre at 2.94 µm. These silica fibres are mechanically and chemically robust, biocompatible and have low sensitivity to bending. A maximum pulse energy of 14 mJ at 2.94 µm was delivered through the fibre. This, to our knowledge, is the first time a silica hollow core photonic crystal fibre has been shown to transmit 2.94 μm laser light at a fluence exceeding the thresholds required for modification (e.g. cutting and drilling) of hard biological tissue. Consequently, laser delivery systems based on these fibres have the potential for the realization of novel, minimally-invasive surgical procedures.

  20. Optics of globular photonic crystals

    SciTech Connect

    Gorelik, V S

    2007-05-31

    The results of experimental and theoretical studies of the optical properties of globular photonic crystals - new physical objects having a crystal structure with the lattice period exceeding considerably the atomic size, are presented. As globular photonic crystals, artificial opal matrices consisting of close-packed silica globules of diameter {approx}200 nm were used. The reflection spectra of these objects characterising the parameters of photonic bands existing in these crystals in the visible spectral region are presented. The idealised models of the energy band structure of photonic crystals investigated in the review give analytic dispersion dependences for the group velocity and the effective photon mass in a globular photonic crystal. The characteristics of secondary emission excited in globular photonic crystals by monochromatic and broadband radiation are presented. The results of investigations of single-photon-excited delayed scattering of light observed in globular photonic crystals exposed to cw UV radiation and radiation from a repetitively pulsed copper vapour laser are presented. The possibilities of using globular photonic crystals as active media for lasing in different spectral regions are considered. It is proposed to use globular photonic crystals as sensitive sensors in optoelectronic devices for molecular analysis of organic and inorganic materials by the modern methods of laser spectroscopy. The results of experimental studies of spontaneous and stimulated globular scattering of light are discussed. The conditions for observing resonance and two-photon-excited delayed scattering of light are found. The possibility of accumulation and localisation of the laser radiation energy inside a globular photonic crystal is reported. (review)

  1. Photonic crystal light source

    DOEpatents

    Fleming, James G.; Lin, Shawn-Yu; Bur, James A.

    2004-07-27

    A light source is provided by a photonic crystal having an enhanced photonic density-of-states over a band of frequencies and wherein at least one of the dielectric materials of the photonic crystal has a complex dielectric constant, thereby producing enhanced light emission at the band of frequencies when the photonic crystal is heated. The dielectric material can be a metal, such as tungsten. The spectral properties of the light source can be easily tuned by modification of the photonic crystal structure and materials. The photonic crystal light source can be heated electrically or other heating means. The light source can further include additional photonic crystals that exhibit enhanced light emission at a different band of frequencies to provide for color mixing. The photonic crystal light source may have applications in optical telecommunications, information displays, energy conversion, sensors, and other optical applications.

  2. Function photonic crystals

    NASA Astrophysics Data System (ADS)

    Wu, Xiang-Yao; Zhang, Bai-Jun; Yang, Jing-Hai; Liu, Xiao-Jing; Ba, Nuo; Wu, Yi-Heng; Wang, Qing-Cai

    2011-07-01

    In this paper, we present a new kind of function photonic crystals (PCs), whose refractive index is a function of space position. Conventional PCs structure grows from two materials, A and B, with different dielectric constants εA and εB. Based on Fermat principle, we give the motion equations of light in one-dimensional, two-dimensional and three-dimensional function photonic crystals. For one-dimensional function photonic crystals, we give the dispersion relation, band gap structure and transmissivity, and compare them with conventional photonic crystals, and we find the following: (1) For the vertical and non-vertical incidence light of function photonic crystals, there are band gap structures, and for only the vertical incidence light, the conventional PCs have band gap structures. (2) By choosing various refractive index distribution functions n( z), we can obtain more wider or more narrower band gap structure than conventional photonic crystals.

  3. Dispersion in photonic crystals

    NASA Astrophysics Data System (ADS)

    Witzens, Jeremy

    2005-11-01

    Investigations on the dispersive properties of photonic crystals, modified scattering in ring-resonators, monolithic integration of vertical-cavity surface-emitting lasers and advanced data processing techniques for the finite-difference time-domain method are presented. Photonic crystals are periodic mesoscopic arrays of scatterers that modify the propagation properties of electromagnetic waves in a similar way as "natural" crystals modify the properties of electrons in solid-state physics. In this thesis photonic crystals are implemented as planar photonic crystals, i.e., optically thin semiconductor films with periodic arrays of holes etched into them, with a hole-to-hole spacing of the order of the wavelength of light in the dielectric media. Photonic crystals can feature forbidden frequency ranges (the band-gaps) in which light cannot propagate. Even though most work on photonic crystals has focused on these band-gaps for application such as confinement and guiding of light, this thesis focuses on the allowed frequency regions (the photonic bands) and investigates how the propagation of light is modified by the crystal lattice. In particular the guiding of light in bulk photonic crystals in the absence of lattice defects (the self-collimation effect) and the angular steering of light in photonic crystals (the superprism effect) are investigated. The latter is used to design a planar lightwave circuit for frequency domain demultiplexion. Difficulties such as efficient insertion of light into the crystal are resolved and previously predicted limitations on the resolution are circumvented. The demultiplexer is also fabricated and characterized. Monolithic integration of vertical-cavity surface-emitting lasers by means of resonantly enhanced grating couplers is investigated. The grating coupler is designed to bend light through a ninety-degree angle and is characterized with the finite-difference time-domain method. The vertical-cavity surface-emitting lasers are

  4. Photonic crystal beam splitters.

    PubMed

    Chen, Chii-Chang; Chien, Hung-Da; Luan, Pi-Gang

    2004-11-20

    This work studies two-dimensional photonic crystal beam splitters with two input ports and two output ports. The beam splitter structure consists of two orthogonally crossed line defects and one point defect in square-lattice photonic crystals. The point defect is positioned at the intersection of the line defects to divide the input power into output ports. If the position and the size of the point defect are varied, the power of two output ports can be identical. The beam splitters can be used in photonic crystal Mach-Zehnder interferometers or switches. The simulation results show that a large bandwidth of the extinction ratio larger than 20 dB can be obtained while two beams are interfered in the beam splitters. This enables photonic crystal beam splitters to be used in fiber optic communication systems.

  5. Spherical colloidal photonic crystals.

    PubMed

    Zhao, Yuanjin; Shang, Luoran; Cheng, Yao; Gu, Zhongze

    2014-12-16

    CONSPECTUS: Colloidal photonic crystals (PhCs), periodically arranged monodisperse nanoparticles, have emerged as one of the most promising materials for light manipulation because of their photonic band gaps (PBGs), which affect photons in a manner similar to the effect of semiconductor energy band gaps on electrons. The PBGs arise due to the periodic modulation of the refractive index between the building nanoparticles and the surrounding medium in space with subwavelength period. This leads to light with certain wavelengths or frequencies located in the PBG being prohibited from propagating. Because of this special property, the fabrication and application of colloidal PhCs have attracted increasing interest from researchers. The most simple and economical method for fabrication of colloidal PhCs is the bottom-up approach of nanoparticle self-assembly. Common colloidal PhCs from this approach in nature are gem opals, which are made from the ordered assembly and deposition of spherical silica nanoparticles after years of siliceous sedimentation and compression. Besides naturally occurring opals, a variety of manmade colloidal PhCs with thin film or bulk morphology have also been developed. In principle, because of the effect of Bragg diffraction, these PhC materials show different structural colors when observed from different angles, resulting in brilliant colors and important applications. However, this angle dependence is disadvantageous for the construction of some optical materials and devices in which wide viewing angles are desired. Recently, a series of colloidal PhC materials with spherical macroscopic morphology have been created. Because of their spherical symmetry, the PBGs of spherical colloidal PhCs are independent of rotation under illumination of the surface at a fixed incident angle of the light, broadening the perspective of their applications. Based on droplet templates containing colloidal nanoparticles, these spherical colloidal PhCs can be

  6. Photonic Crystal Microchip Laser

    PubMed Central

    Gailevicius, Darius; Koliadenko, Volodymyr; Purlys, Vytautas; Peckus, Martynas; Taranenko, Victor; Staliunas, Kestutis

    2016-01-01

    The microchip lasers, being very compact and efficient sources of coherent light, suffer from one serious drawback: low spatial quality of the beam strongly reducing the brightness of emitted radiation. Attempts to improve the beam quality, such as pump-beam guiding, external feedback, either strongly reduce the emission power, or drastically increase the size and complexity of the lasers. Here it is proposed that specially designed photonic crystal in the cavity of a microchip laser, can significantly improve the beam quality. Experiments show that a microchip laser, due to spatial filtering functionality of intracavity photonic crystal, improves the beam quality factor M2 reducing it by a factor of 2, and increase the brightness of radiation by a factor of 3. This comprises a new kind of laser, the “photonic crystal microchip laser”, a very compact and efficient light source emitting high spatial quality high brightness radiation. PMID:27683066

  7. Photonic Crystal Microchip Laser

    NASA Astrophysics Data System (ADS)

    Gailevicius, Darius; Koliadenko, Volodymyr; Purlys, Vytautas; Peckus, Martynas; Taranenko, Victor; Staliunas, Kestutis

    2016-09-01

    The microchip lasers, being very compact and efficient sources of coherent light, suffer from one serious drawback: low spatial quality of the beam strongly reducing the brightness of emitted radiation. Attempts to improve the beam quality, such as pump-beam guiding, external feedback, either strongly reduce the emission power, or drastically increase the size and complexity of the lasers. Here it is proposed that specially designed photonic crystal in the cavity of a microchip laser, can significantly improve the beam quality. Experiments show that a microchip laser, due to spatial filtering functionality of intracavity photonic crystal, improves the beam quality factor M2 reducing it by a factor of 2, and increase the brightness of radiation by a factor of 3. This comprises a new kind of laser, the “photonic crystal microchip laser”, a very compact and efficient light source emitting high spatial quality high brightness radiation.

  8. EDITORIAL: Photonic Crystal Devices

    NASA Astrophysics Data System (ADS)

    Bhattacharya, Pallab K.

    2007-05-01

    The engineering of electromagnetic modes at optical frequencies in artificial dielectric structures with periodic and random variation of the refractive index, enabling control of the radiative properties of the materials and photon localization, was first proposed independently by Yablonovitch and John in 1987. It is possible to control the flow of light in the periodic dielectric structures, known as photonic crystals (PC). As light waves scatter within the photonic crystal, destructive interference cancels out light of certain wavelengths, thereby forming a photonic bandgap, similar to the energy bandgap for electron waves in a semiconductor. Photons whose energies lie within the gap cannot propagate through the periodic structure. This property can be used to make a low-loss cavity. If a point defect, such as one or more missing periods, is introduced into the periodic structure a region is obtained within which the otherwise forbidden wavelengths can be locally trapped. This property can be used to realize photonic microcavities. Similarly, a line of defects can serve as a waveguide. While the realization of three-dimensional (3D) photonic crystals received considerable attention initially, planar two-dimensional (2D) structures are currently favoured because of their relative ease of fabrication. 2D photonic crystal structures provide most of the functionality of 3D structures. These attributes have generated worldwide research and development of sub-μm and μm size active and passive photonic devices such as single-mode and non- classical light sources, guided wave devices, resonant cavity detection, and components for optical communication. More recently, photonic crystal guided wave devices are being investigated for application in microfludic and biochemical sensing. Photonic crystal devices have been realized with bulk, quantum well and quantum dot active regions. The Cluster of articles in this issue of Journal of Physics D: Applied Physics provides a

  9. Photonic crystal optical memory

    NASA Astrophysics Data System (ADS)

    Lima, A. Wirth; Sombra, A. S. B.

    2011-06-01

    After several decades pushing the technology and the development of the world, the electronics is giving space for technologies that use light. We propose and analyze an optical memory embedded in a nonlinear photonic crystal (PhC), whose system of writing and reading data is controlled by an external command signal. This optical memory is based on optical directional couplers connected to a shared optical ring. Such a device can work over the C-Band of ITU (International Telecommunication Union).

  10. Slotted Photonic Crystal Sensors

    PubMed Central

    Scullion, Mark G.; Krauss, Thomas F.; Di Falco, Andrea

    2013-01-01

    Optical biosensors are increasingly being considered for lab-on-a-chip applications due to their benefits such as small size, biocompatibility, passive behaviour and lack of the need for fluorescent labels. The light guiding mechanisms used by many of them results in poor overlap of the optical field with the target molecules, reducing the maximum sensitivity achievable. This review article presents a new platform for optical biosensors, namely slotted photonic crystals, which provide higher sensitivities due to their ability to confine, spatially and temporally, the optical mode peak within the analyte itself. Loss measurements showed values comparable to standard photonic crystals, confirming their ability to be used in real devices. A novel resonant coupler was designed, simulated, and experimentally tested, and was found to perform better than other solutions within the literature. Combining with cavities, microfluidics and biological functionalization allowed proof-of-principle demonstrations of protein binding to be carried out. Higher sensitivities were observed in smaller structures than possible with most competing devices reported in the literature. This body of work presents slotted photonic crystals as a realistic platform for complete on-chip biosensing; addressing key design, performance and application issues, whilst also opening up exciting new ideas for future study. PMID:23503295

  11. Slotted photonic crystal sensors.

    PubMed

    Scullion, Mark G; Krauss, Thomas F; Di Falco, Andrea

    2013-01-01

    Optical biosensors are increasingly being considered for lab-on-a-chip applications due to their benefits such as small size, biocompatibility, passive behaviour and lack of the need for fluorescent labels. The light guiding mechanisms used by many of them results in poor overlap of the optical field with the target molecules, reducing the maximum sensitivity achievable. This review article presents a new platform for optical biosensors, namely slotted photonic crystals, which provide higher sensitivities due to their ability to confine, spatially and temporally, the optical mode peak within the analyte itself. Loss measurements showed values comparable to standard photonic crystals, confirming their ability to be used in real devices. A novel resonant coupler was designed, simulated, and experimentally tested, and was found to perform better than other solutions within the literature. Combining with cavities, microfluidics and biological functionalization allowed proof-of-principle demonstrations of protein binding to be carried out. Higher sensitivities were observed in smaller structures than possible with most competing devices reported in the literature. This body of work presents slotted photonic crystals as a realistic platform for complete on-chip biosensing; addressing key design, performance and application issues, whilst also opening up exciting new ideas for future study. PMID:23503295

  12. Inverse opal photonic crystal of chalcogenide glass by solution processing.

    PubMed

    Kohoutek, Tomas; Orava, Jiri; Sawada, Tsutomu; Fudouzi, Hiroshi

    2011-01-15

    Chalcogenide opal and inverse opal photonic crystals were successfully fabricated by low-cost and low-temperature solution-based process, which is well developed in polymer films processing. Highly ordered silica colloidal crystal films were successfully infilled with nano-colloidal solution of the high refractive index As(30)S(70) chalcogenide glass by using spin-coating method. The silica/As-S opal film was etched in HF acid to dissolve the silica opal template and fabricate the inverse opal As-S photonic crystal. Both, the infilled silica/As-S opal film (Δn ~ 0.84 near λ=770 nm) and the inverse opal As-S photonic structure (Δn ~ 1.26 near λ=660 nm) had significantly enhanced reflectivity values and wider photonic bandgaps in comparison with the silica opal film template (Δn ~ 0.434 near λ=600 nm). The key aspects of opal film preparation by spin-coating of nano-colloidal chalcogenide glass solution are discussed. The solution fabricated "inorganic polymer" opal and the inverse opal structures exceed photonic properties of silica or any organic polymer opal film. The fabricated photonic structures are proposed for designing novel flexible colloidal crystal laser devices, photonic waveguides and chemical sensors.

  13. Natural photonic crystals

    NASA Astrophysics Data System (ADS)

    Vigneron, Jean Pol; Simonis, Priscilla

    2012-10-01

    Photonic structures appeared in nature several hundred millions years ago. In the living world, color is used for communication and this important function strongly impacts the individual chances of survival as well as the chances to reproduce. This has a statistical influence on species populations. Therefore, because they are involved in evolution, natural color-generating structures are - from some point of view - highly optimized. In this short review, a survey is presented of the development of natural photonic crystal-type structures occurring in insects, spiders, birds, fishes and other marine animals, in plants and more, from the standpoint of light-waves propagation. One-, two-, and three-dimensional structures will be reviewed with selected examples.

  14. Photonic crystal fibers in biophotonics

    NASA Astrophysics Data System (ADS)

    Tuchin, Valery V.; Skibina, Julia S.; Malinin, Anton V.

    2011-12-01

    We observed recent experimental results in area of photonic crystal fibers appliance. Possibility of creation of fiberbased broadband light sources for high resolution optical coherence tomography is discussed. Using of femtosecond pulse laser allows for generation of optical radiation with large spectral width in highly nonlinear solid core photonic crystal fibers. Concept of exploitation of hollow core photonic crystal fibers in optical sensing is demonstrated. The use of photonic crystal fibers as "smart cuvette" gives rise to efficiency of modern optical biomedical analysis methods.

  15. Passive polarization rotator based on silica photonic crystal fiber for 1.31-μm and 1.55-μm bands via adjusting the fiber length

    NASA Astrophysics Data System (ADS)

    Chen, Lei; Zhang, Wei-Gang; Wang, Li; Bai, Zhi-Yong; Zhang, Shan-Shan; Wang, Biao; Yan, Tie-Yi; Jonathan, Sieg

    2014-10-01

    A new polarization rotator based on the silica photonic crystal fiber is proposed. The proposed polarization rotator photonic crystal fiber (PR-PCF) possesses a triangle jigsaw-shape core region. The full-vector finite-element method is used to analyze the phenomenon of polarization conversion between the quasi-TE and quasi-TM modes. Numerical simulations show that the wavelengths of 1.31 μm and 1.55 μm are converted with a nearly 100% polarization conversion ratio with their matched coupling length and has a relatively strong realistic fabrication tolerance -100 nm on the y axis and 50 nm on the x axis. The full vectorial finite difference beam propagation method is used to confirm the performance of the proposed PR-PCF.

  16. Photonic Crystal Nanolaser Biosensors

    NASA Astrophysics Data System (ADS)

    Kita, Shota; Otsuka, Shota; Hachuda, Shoji; Endo, Tatsuro; Imai, Yasunori; Nishijima, Yoshiaki; Misawa, Hiroaki; Baba, Toshihiko

    High-performance and low-cost sensors are critical devices for high-throughput analyses of bio-samples in medical diagnoses and life sciences. In this paper, we demonstrate photonic crystal nanolaser sensor, which detects the adsorption of biomolecules from the lasing wavelength shift. It is a promising device, which balances a high sensitivity, high resolution, small size, easy integration, simple setup and low cost. In particular with a nanoslot structure, it achieves a super-sensitivity in protein sensing whose detection limit is three orders of magnitude lower than that of standard surface-plasmon-resonance sensors. Our investigations indicate that the nanoslot acts as a protein condenser powered by the optical gradient force, which arises from the strong localization of laser mode in the nanoslot.

  17. Random photonic crystal optical memory

    NASA Astrophysics Data System (ADS)

    Wirth Lima, A., Jr.; Sombra, A. S. B.

    2012-10-01

    Currently, optical cross-connects working on wavelength division multiplexing systems are based on optical fiber delay lines buffering. We designed and analyzed a novel photonic crystal optical memory, which replaces the fiber delay lines of the current optical cross-connect buffer. Optical buffering systems based on random photonic crystal optical memory have similar behavior to the electronic buffering systems based on electronic RAM memory. In this paper, we show that OXCs working with optical buffering based on random photonic crystal optical memories provides better performance than the current optical cross-connects.

  18. Configurable silicon photonic crystal waveguides

    NASA Astrophysics Data System (ADS)

    Prorok, Stefan; Petrov, Alexander; Eich, Manfred; Luo, Jingdong; Jen, Alex K.-Y.

    2013-12-01

    In this Letter, we demonstrate that the mode cut off of a photonic crystal waveguide can be trimmed with high accuracy by electron beam bleaching of a chromophore doped polymer cladding. Using this method, configurable waveguides are realized, which allow for spatially resolved changes of the photonic crystal's effective lattice constant as small as 7.6 pm. We show three different examples how to take advantage of configurable photonic crystal waveguides: Shifting of the complete transmission spectrum, definition of cavities with high quality factor, and tuning of existing cavities.

  19. Multicolor photonic crystal laser array

    SciTech Connect

    Wright, Jeremy B; Brener, Igal; Subramania, Ganapathi S; Wang, George T; Li, Qiming

    2015-04-28

    A multicolor photonic crystal laser array comprises pixels of monolithically grown gain sections each with a different emission center wavelength. As an example, two-dimensional surface-emitting photonic crystal lasers comprising broad gain-bandwidth III-nitride multiple quantum well axial heterostructures were fabricated using a novel top-down nanowire fabrication method. Single-mode lasing was obtained in the blue-violet spectral region with 60 nm of tuning (or 16% of the nominal center wavelength) that was determined purely by the photonic crystal geometry. This approach can be extended to cover the entire visible spectrum.

  20. Configurable silicon photonic crystal waveguides

    SciTech Connect

    Prorok, Stefan; Petrov, Alexander; Eich, Manfred; Luo, Jingdong; Jen, Alex K.-Y.

    2013-12-23

    In this Letter, we demonstrate that the mode cut off of a photonic crystal waveguide can be trimmed with high accuracy by electron beam bleaching of a chromophore doped polymer cladding. Using this method, configurable waveguides are realized, which allow for spatially resolved changes of the photonic crystal's effective lattice constant as small as 7.6 pm. We show three different examples how to take advantage of configurable photonic crystal waveguides: Shifting of the complete transmission spectrum, definition of cavities with high quality factor, and tuning of existing cavities.

  1. Biomimetic Photonic Crystals based on Diatom Algae Frustules

    NASA Astrophysics Data System (ADS)

    Mishler, Jonathan; Alverson, Andrew; Herzog, Joseph

    2015-03-01

    Diatom algae are unicellular, photosynthetic microorganisms with a unique external shell known as a frustule. Frustules, which are composed of amorphous silica, exhibit a unique periodic nano-patterning, distinguishing diatoms from other types of phytoplankton. Diatoms have been studied for their distinctive optical properties due to their resemblance of photonic crystals. In this regard, diatoms are not only considered for their applications as photonic crystals, but also for their use as biomimetic templates for artificially fabricated photonic crystals. Through the examination and measurement of the physical characteristics of many scanning electron microscope (SEM) images of diatom frustules, a biomimetic photonic crystal derived from diatom frustules can be recreated and modeled with the finite element method. In this approach, the average geometries of the diatom frustules are used to recreate a 2-dimensional photonic crystal, after which the electric field distribution and optical transmission through the photonic crystal are both measured. The optical transmission is then compared to the transmission spectra of a regular hexagonal photonic crystal, revealing the effects of diatom geometry on their optical properties. Finally, the dimensions of the photonic crystal are parametrically swept, allowing for further control over the transmission of light through the photonic crystal.

  2. Spatial filtering with photonic crystals

    SciTech Connect

    Maigyte, Lina; Staliunas, Kestutis

    2015-03-15

    Photonic crystals are well known for their celebrated photonic band-gaps—the forbidden frequency ranges, for which the light waves cannot propagate through the structure. The frequency (or chromatic) band-gaps of photonic crystals can be utilized for frequency filtering. In analogy to the chromatic band-gaps and the frequency filtering, the angular band-gaps and the angular (spatial) filtering are also possible in photonic crystals. In this article, we review the recent advances of the spatial filtering using the photonic crystals in different propagation regimes and for different geometries. We review the most evident configuration of filtering in Bragg regime (with the back-reflection—i.e., in the configuration with band-gaps) as well as in Laue regime (with forward deflection—i.e., in the configuration without band-gaps). We explore the spatial filtering in crystals with different symmetries, including axisymmetric crystals; we discuss the role of chirping, i.e., the dependence of the longitudinal period along the structure. We also review the experimental techniques to fabricate the photonic crystals and numerical techniques to explore the spatial filtering. Finally, we discuss several implementations of such filters for intracavity spatial filtering.

  3. Partial confinement photonic crystal waveguides

    SciTech Connect

    Saini, S.; Hong, C.-Y.; Pfaff, N.; Kimerling, L. C.; Michel, J.

    2008-12-29

    One-dimensional photonic crystal waveguides with an incomplete photonic band gap are modeled and proposed for an integration application that exploits their property of partial angular confinement. Planar apodized photonic crystal structures are deposited by plasma enhanced chemical vapor deposition and characterized by reflectivity as a function of angle and polarization, validating a partial confinement design for light at 850 nm wavelength. Partial confinement identifies an approach for tailoring waveguide properties by the exploitation of conformal film deposition over a substrate with angularly dependent topology. An application for an optoelectronic transceiver is demonstrated.

  4. Manufacturing method of photonic crystal

    SciTech Connect

    Park, In Sung; Lee, Tae Ho; Ahn, Jin Ho; Biswas, Rana; Constant, Kristen P.; Ho, Kai-Ming; Lee, Jae-Hwang

    2013-01-29

    A manufacturing method of a photonic crystal is provided. In the method, a high-refractive-index material is conformally deposited on an exposed portion of a periodic template composed of a low-refractive-index material by an atomic layer deposition process so that a difference in refractive indices or dielectric constants between the template and adjacent air becomes greater, which makes it possible to form a three-dimensional photonic crystal having a superior photonic bandgap. Herein, the three-dimensional structure may be prepared by a layer-by-layer method.

  5. Mechanically tunable photonic crystal lens

    NASA Astrophysics Data System (ADS)

    Cui, Y.; Tamma, V. A.; Lee, J.-B.; Park, W.

    2010-08-01

    We designed, fabricated and characterized MEMS-enabled mechanically-tunable photonic crystal lens comprised of 2D photonic crystal and symmetrical electro-thermal actuators. The 2D photonic crystal was made of a honeycomb-lattice of 340 nm thick, 260 nm diameter high-index silicon rods embedded in low-index 10 μm thick SU-8 cladding. Silicon input waveguide and deflection block were also fabricated for light in-coupling and monitoring of focused spot size, respectively. When actuated, the electro-thermal actuators induced mechanical strain which changed the lattice constant of the photonic crystal and consequently modified the photonic band structure. This in turn modified the focal-length of the photonic crystal lens. The fabricated device was characterized using a tunable laser (1400~1602 nm) and an infrared camera during actuation. At the wavelength of 1450 nm, the lateral light spot size observed at the deflection block gradually decreased 40%, as applied current increased from 0 to 0.7 A, indicating changes in focal length in response to the mechanical stretching.

  6. Simplified hollow-core photonic crystal fiber.

    PubMed

    Gérôme, Frédéric; Jamier, Raphaël; Auguste, Jean-Louis; Humbert, Georges; Blondy, Jean-Marc

    2010-04-15

    An original design of hollow-core photonic crystal fiber composed of a thin silica ring suspended in air by six silica struts is proposed. This structure can be viewed as a simplified Kagomé-lattice fiber reduced to one layer of air holes. By working on the core surround parameters, an efficient antiresonant air guiding was successfully demonstrated. Two large low-loss windows (visible/IR) were measured with a minimum attenuation less than 0.2 dB radicalm at yellow wavelengths, comparable with state-of-the-art designs. The curvature behavior was also studied, showing low bending loss sensitivity for the fundamental transmission band. These relevant features might open a new route to propose original hollow-core fiber designs while making their production simpler and faster than previously.

  7. Radiating dipoles in photonic crystals

    PubMed

    Busch; Vats; John; Sanders

    2000-09-01

    The radiation dynamics of a dipole antenna embedded in a photonic crystal are modeled by an initially excited harmonic oscillator coupled to a non-Markovian bath of harmonic oscillators representing the colored electromagnetic vacuum within the crystal. Realistic coupling constants based on the natural modes of the photonic crystal, i.e., Bloch waves and their associated dispersion relation, are derived. For simple model systems, well-known results such as decay times and emission spectra are reproduced. This approach enables direct incorporation of realistic band structure computations into studies of radiative emission from atoms and molecules within photonic crystals. We therefore provide a predictive and interpretative tool for experiments in both the microwave and optical regimes.

  8. Self-assembled photonic crystals for a chemical sensing

    NASA Astrophysics Data System (ADS)

    Bourdillon, C.; Gam Derouich, S.; Daney de Marcillac, W.; Coolen, L.; Maître, A.; Mangeney, C.; Schwob, C.

    2016-03-01

    As they allow the control of light propagation, photonic crystals find many fields of application. Among them, self-assembled 3D-photonic crystals are ordered at the nanometric scale over centrimetric areas. Furthermore, self-assembly allows the design of complexes structures leading, for example, to the controlled disruption of the crystal periodicity (called defect) and the appearance of permitted optical frequency bands within the photonic bandgap. Light frequencies included in the corresponding passband are then localized in the defect allowing manipulation of nano-emitters fluorescence. We present the fabrication and the optical characterization of a heterostructure composed of a sputtered silica layer sandwiched between two silica opals. We show by photoluminescence measurements than this structure strongly modifies the transmitted fluorescence of nanocrystals.

  9. Uniform silica nanoparticles encapsulating two-photon absorbing fluorescent dye

    SciTech Connect

    Wu Weibing; Liu Chang; Wang Mingliang; Huang Wei; Zhou Shengrui; Jiang Wei; Sun Yueming; Cui Yiping; Xu Chunxinag

    2009-04-15

    We have prepared uniform silica nanoparticles (NPs) doped with a two-photon absorbing zwitterionic hemicyanine dye by reverse microemulsion method. Obvious solvatochromism on the absorption spectra of dye-doped NPs indicates that solvents can partly penetrate into the silica matrix and then affect the ground and excited state of dye molecules. For dye-doped NP suspensions, both one-photon and two-photon excited fluorescence are much stronger and recorded at shorter wavelength compared to those of free dye solutions with comparative overall dye concentration. This behavior is possibly attributed to the restricted twisted intramolecular charge transfer (TICT), which reduces fluorescence quenching when dye molecules are trapped in the silica matrix. Images from two-photon laser scanning fluorescence microscopy demonstrate that the dye-doped silica NPs can be actively uptaken by Hela cells with low cytotoxicity. - Graphical abstract: Water-soluble silica NPs doped with a two-photon absorbing zwitterionic hemicyanine dye were prepared. They were found of enhanced one-photon and two-photon excited fluorescence compared to free dye solutions. Images from two-photon laser scanning fluorescence microscopy demonstrate that the dye-doped silica NPs can be actively uptaken by Hela cells.

  10. Crystallization of hollow mesoporous silica nanoparticles.

    PubMed

    Drisko, Glenna L; Carretero-Genevrier, Adrian; Perrot, Alexandre; Gich, Martí; Gàzquez, Jaume; Rodriguez-Carvajal, Juan; Favre, Luc; Grosso, David; Boissière, Cédric; Sanchez, Clément

    2015-03-11

    Complex 3D macrostructured nanoparticles are transformed from amorphous silica into pure polycrystalline α-quartz using catalytic quantities of alkaline earth metals as devitrifying agent. Walls as thin as 10 nm could be crystallized without losing the architecture of the particles. The roles of cation size and the mol% of the incorporated devitrifying agent in crystallization behavior are studied, with Mg(2+), Ca(2+), Sr(2+) and Ba(2+) all producing pure α-quartz under certain conditions.

  11. [Photonic crystals for analytical chemistry].

    PubMed

    Chen, Yi; Li, Jincheng

    2009-09-01

    Photonic crystals, originally created to control the transmission of light, have found their increasing value in the field of analytical chemistry and are probable to become a hot research area soon. This review is hence composed, focusing on their analytical chemistry-oriented applications, including especially their use in chromatography, capillary- and chip-based electrophoresis.

  12. Photonic crystal surface-emitting lasers

    SciTech Connect

    Chua, Song Liang; Lu, Ling; Soljacic, Marin

    2015-06-23

    A photonic-crystal surface-emitting laser (PCSEL) includes a gain medium electromagnetically coupled to a photonic crystal whose energy band structure exhibits a Dirac cone of linear dispersion at the center of the photonic crystal's Brillouin zone. This Dirac cone's vertex is called a Dirac point; because it is at the Brillouin zone center, it is called an accidental Dirac point. Tuning the photonic crystal's band structure (e.g., by changing the photonic crystal's dimensions or refractive index) to exhibit an accidental Dirac point increases the photonic crystal's mode spacing by orders of magnitudes and reduces or eliminates the photonic crystal's distributed in-plane feedback. Thus, the photonic crystal can act as a resonator that supports single-mode output from the PCSEL over a larger area than is possible with conventional PCSELs, which have quadratic band edge dispersion. Because output power generally scales with output area, this increase in output area results in higher possible output powers.

  13. Investigations of properties of opal-like photonic crystals using combined methods

    NASA Astrophysics Data System (ADS)

    Akhmadeev, A. A.; Salakhov, M. Kh

    2016-05-01

    We propose a technique that combines atomic force microscopy, optical spectrophotometry and diffraction method for characterization of photonic crystals. These materials are promising for the creation of various devices, as well as for the observation of new effects due to their unique properties. Photonic crystals were synthesized by self-assembly of colloidal silica particles with low deviation in size. It is shown that the developed technique allows to increase the accuracy of determining the parameters of the photonic crystal.

  14. Liquid crystal applications in photonics

    NASA Astrophysics Data System (ADS)

    Chigrinov, Vladimir G.

    2009-02-01

    Liquid crystal (LC) devices for Photonics applications is a hot topic of research. Such elements begin to appear in Photonics market. Passive elements for fiber optical communication systems (DWDM components) based on LC cells can successfully compete with the other elements used for the purpose, such as micro electromechanical (MEM), thermo-optical, opto-mechanical or acousto-optical devices. We have already successfully fabricated certain prototypes of the optical switches based on various electrooptic modes in ferroelectric and nematic LC materials. The electrooptical modes used for the purpose included the light polarization rotation, voltage controllable diffraction and fast switching of the LC refractive index. Use of photo-alignment technique pioneered by us makes it possible to develop new LC fiber components. Almost all the criteria of perfect LC alignment are met in case of azo-dye layers. We have already used azo-dye materials to align LC in superthin photonic holes, curved and 3D surfaces and as cladding layers in microring silicon based resonators. We have already used the photoaligning materials to align LC mixtures in small cavities, such as the holes and tubes of photonic crystals, having size of 1 μm and less and obtained excellent LC orientation inside the tubes by photoalignment. The prototypes of new LC efficient Photonics devices, such as optically rewritable LC waveguides and voltage controllable diffraction gratings are envisaged. The polarization controllers, polarization rotators, variable optical attenuators and other passive LC optical elements for fiber communication networks are under way.

  15. Inhibited coupling hollow-core photonic crystal fiber

    NASA Astrophysics Data System (ADS)

    Benabid, F.; Gérôme, F.; Vincetti, L.; Debord, B.; Alharbi, M.; Bradley, T.

    2014-02-01

    We review the recent progress on the enhanced inhibited coupling in kagome hollow-core photonic crystal fiber by introducing negative curvature in the fiber-core shape. We show that increasing the hypocycloid contour curvature leads to a dramatic decrease in transmission loss and optical overlap with the silica surround and to a single modedness. Fabricated hypocycloid-core hollow-core photonic crystal fibers with a transmission loss in the range of 20-40 dB/km and for a spectral range of 700 nm-2000 nm have now become typical.

  16. Optical Magnetometer Incorporating Photonic Crystals

    NASA Technical Reports Server (NTRS)

    Kulikov, Igor; Florescu, Lucia

    2007-01-01

    According to a proposal, photonic crystals would be used to greatly increase the sensitivities of optical magnetometers that are already regarded as ultrasensitive. The proposal applies, more specifically, to a state-of-the-art type of quantum coherent magnetometer that exploits the electromagnetically-induced-transparency (EIT) method for determining a small change in a magnetic field indirectly via measurement of the shift, induced by that change, in the hyperfine levels of resonant atoms exposed to the field.

  17. Hybrid colloidal plasmonic-photonic crystals.

    PubMed

    Romanov, Sergei G; Korovin, Alexander V; Regensburger, Alois; Peschel, Ulf

    2011-06-17

    We review the recently emerged class of hybrid metal-dielectric colloidal photonic crystals. The hybrid approach is understood as the combination of a dielectric photonic crystal with a continuous metal film. It allows to achieve a strong modification of the optical properties of photonic crystals by involving the light scattering at electronic excitations in the metal component into moulding of the light flow in series to the diffraction resonances occurring in the body of the photonic crystal. We consider different realizations of hybrid plasmonic-photonic crystals based on two- and three-dimensional colloidal photonic crystals in association with flat and corrugated metal films. In agreement with model calculations, different resonance phenomena determine the optical response of hybrid crystals leading to a broadly tuneable functionality of these crystals. PMID:21594906

  18. Topological photonic crystal with equifrequency Weyl points

    NASA Astrophysics Data System (ADS)

    Wang, Luyang; Jian, Shao-Kai; Yao, Hong

    2016-06-01

    Weyl points in three-dimensional photonic crystals behave as monopoles of Berry flux in momentum space. Here, based on general symmetry analysis, we show that a minimal number of four symmetry-related (consequently equifrequency) Weyl points can be realized in time-reversal invariant photonic crystals. We further propose an experimentally feasible way to modify double-gyroid photonic crystals to realize four equifrequency Weyl points, which is explicitly confirmed by our first-principle photonic band-structure calculations. Remarkably, photonic crystals with equifrequency Weyl points are qualitatively advantageous in applications including angular selectivity, frequency selectivity, invisibility cloaking, and three-dimensional imaging.

  19. Topological photonic crystal with ideal Weyl points

    NASA Astrophysics Data System (ADS)

    Wang, Luyang; Jian, Shao-Kai; Yao, Hong

    Weyl points in three-dimensional photonic crystals behave as monopoles of Berry flux in momentum space. Here, based on symmetry analysis, we show that a minimal number of symmetry-related Weyl points can be realized in time-reversal invariant photonic crystals. We propose to realize these ``ideal'' Weyl points in modified double-gyroid photonic crystals, which is confirmed by our first-principle photonic band-structure calculations. Photonic crystals with ideal Weyl points are qualitatively advantageous in applications such as angular and frequency selectivity, broadband invisibility cloaking, and broadband 3D-imaging.

  20. Resonant photonic States in coupled heterostructure photonic crystal waveguides.

    PubMed

    Cox, Jd; Sabarinathan, J; Singh, Mr

    2010-01-01

    In this paper, we study the photonic resonance states and transmission spectra of coupled waveguides made from heterostructure photonic crystals. We consider photonic crystal waveguides made from three photonic crystals A, B and C, where the waveguide heterostructure is denoted as B/A/C/A/B. Due to the band structure engineering, light is confined within crystal A, which thus act as waveguides. Here, photonic crystal C is taken as a nonlinear photonic crystal, which has a band gap that may be modified by applying a pump laser. We have found that the number of bound states within the waveguides depends on the width and well depth of photonic crystal A. It has also been found that when both waveguides are far away from each other, the energies of bound photons in each of the waveguides are degenerate. However, when they are brought close to each other, the degeneracy of the bound states is removed due to the coupling between them, which causes these states to split into pairs. We have also investigated the effect of the pump field on photonic crystal C. We have shown that by applying a pump field, the system may be switched between a double waveguide to a single waveguide, which effectively turns on or off the coupling between degenerate states. This reveals interesting results that can be applied to develop new types of nanophotonic devices such as nano-switches and nano-transistors.

  1. Cholesteric liquid crystal photonic crystal lasers and photonic devices

    NASA Astrophysics Data System (ADS)

    Zhou, Ying

    This dissertation discusses cholesteric liquid crystals (CLCs) and polymers based photonic devices including one-dimensional (1D) photonic crystal lasers and broadband circular polarizers. CLCs showing unique self-organized chiral structures have been widely used in bistable displays, flexible displays, and reflectors. However, the photonic band gap they exhibit opens a new way for generating laser light at the photonic band edge (PBE) or inside the band gap. When doped with an emissive laser dye, cholesteric liquid crystals provide distributed feedback so that mirrorless lasing is hence possible. Due to the limited surface anchoring, the thickness of gain medium and feedback length is tens of micrometers. Therefore lasing efficiency is quite limited and laser beam is highly divergent. To meet the challenges, we demonstrated several new methods to enhance the laser emission while reducing the beam divergence from a cholesteric liquid crystal laser. Enhanced laser emission is demonstrated by incorporating a single external CLC reflector as a polarization conserved reflector. Because the distributed feedback from the active layer is polarization selective, a CLC reflector preserves the original polarization of the reflected light and a further stimulated amplification ensues. As a result of virtually doubled feedback length, the output is dramatically enhanced in the same circular polarization state. Meanwhile, the laser beam divergence is dramatically reduced due to the increased cavity length from micrometer to millimeter scale. Enhanced laser emission is also demonstrated by the in-cell metallic reflector because the active layer is pumped twice. Unlike a CLC reflector, the output from a mirror-reflected CLC laser is linearly polarized as a result of coherent superposition of two orthogonal circular polarization states. The output linear polarization direction can be well controlled and fine tuned by varying the operating temperature and cell gap. Enhanced laser

  2. Photonic crystal horn and array antennas.

    PubMed

    Weily, Andrew R; Esselle, Karu P; Sanders, Barry C

    2003-07-01

    We introduce a defect-based horn antenna in a two-dimensional photonic crystal. Our numerical simulations demonstrate the efficient, highly directional nature of the antenna. It has a large operating bandwidth, low loss, and an operating frequency that is scalable to various regions of the electromagnetic spectrum. We also show that the photonic crystal horn antenna can be successfully used in an array configuration that uses a feed network made from photonic crystal waveguide circuits. The feed network and antennas have been integrated into a single photonic crystal device. This photonic crystal array antenna is shown to have high directivity and compact size while retaining the advantages of the photonic crystal horn antenna.

  3. Monochromatic Wannier Functions in the Theory of 2D Photonic Crystals and Photonic Crystal Fibers

    SciTech Connect

    Mazhirina, Yu. A.; Melnikov, L. A.

    2011-10-03

    The use of the monochromatic Wannier functions which have the temporal dependence as (exp(-i{omega}t)) in the theory of 2D photonic crystals and photonic crystal fibers is proposed. Corresponding equations and formulae are derived and discussed.

  4. Photoscattering effect in supercontinuum-generating photonic crystal fiber

    PubMed Central

    Tu, H.; Marks, D. L.; Jiang, Z.; Boppart, S. A.

    2010-01-01

    A photosensitivity different from that responsible for fiber grating inscription is found in a supercontinuum-generating photonic crystal fiber transmitting intense 818 nm femtosecond pulses. This photosensitivity progressively generates a waveguide at the entrance of the fiber to scatter light of specific wavelengths and is termed as the photoscattering effect. This effect is linked to the ~800 nm photosensitivity in the microlithography of bulk silica glass. While the effect somewhat limits fiber-optic supercontinuum applications, it can be beneficial to produce new photonic devices. PMID:21350681

  5. Tunable liquid crystal photonic devices

    NASA Astrophysics Data System (ADS)

    Fan, Yun-Hsing

    2005-07-01

    Liquid crystal (LC)-based adaptive optics are important for information processing, optical interconnections, photonics, integrated optics, and optical communications due to their tunable optical properties. In this dissertation, we describe novel liquid crystal photonic devices. In Chap. 3, we demonstrate a novel electrically tunable-efficiency Fresnel lens which is devised for the first time using nanoscale PDLC. The tunable Fresnel lens is very desirable to eliminate the need of external spatial light modulator. The nanoscale LC devices are polarization independent and exhibit a fast response time. Because of the small droplet sizes, the operating voltage is higher than 100 Vrms. To lower the driving voltage, in Chap. 2 and Chap. 3, we have investigated tunable Fresnel lens using polymer-network liquid crystal (PNLC) and phase-separated composite film (PSCOF). The operating voltage is below 12 Vrms. The PNLC and PSCOF devices are polarization dependent. To overcome this shortcoming, stacking two cells with orthogonal alignment directions is a possibility. Using PNLC, we also demonstrated LC blazed grating. The diffraction efficiency of these devices is continuously controlled by the electric field. We also develop a system with continuously tunable focal length. A conventional mechanical zooming system is bulky and power hungry. In Chap. 4, we developed an electrically tunable-focus flat LC spherical lens and microlens array. A huge tunable range from 0.6 m to infinity is achieved by the applied voltage. In Chap. 5, we describe a LC microlens array whose focal length can be switched from positive to negative by the applied voltage. The fast response time feature of our LC microlens array will be very helpful in developing 3-D animated images. In Chap. 6, we demonstrate polymer network liquid crystals for switchable polarizers and optical shutters. The use of dual-frequency liquid crystal and special driving scheme leads to a sub-millisecond response time. In

  6. Photonic crystal fibers for food quality analysis

    NASA Astrophysics Data System (ADS)

    Malinin, A. V.; Zanishevskaja, A. A.; Tuchin, V. V.; Skibina, Yu. S.; Silokhin, I. Y.

    2012-06-01

    The aspects of application of the hollow core photonic crystal waveguides for spectroscopic analysis of liquid medium were considered. The possibility of using these structures for analysis of a fruit juice was evaluated. The principles of processing of photonic crystal waveguide transmission spectra, which is sensitive to quality of juice, its composition, and main component concentration, were revealed.

  7. Lasing dynamics of photonic crystal reflector laser

    NASA Astrophysics Data System (ADS)

    Bakoz, Andrei P.; Liles, A. A.; Viktorov, E. A.; O'Faolain, L.; Habruseva, T.; Huyet, G.; Hegarty, S. P.

    2016-04-01

    We describe the lasing characteristics of a compact tunable laser source formed by the butt-coupling of a reflective indium phosphide optical amplifier to an SU8 waveguide coupled to few-mode photonic crystal reflector. The short cavity length ensured that only a single longitudinal mode of the device could overlap with each photonic crystal reflection peak.

  8. Photonic crystal scintillators and methods of manufacture

    SciTech Connect

    Torres, Ricardo D.; Sexton, Lindsay T.; Fuentes, Roderick E.; Cortes-Concepcion, Jose

    2015-08-11

    Photonic crystal scintillators and their methods of manufacture are provided. Exemplary methods of manufacture include using a highly-ordered porous anodic alumina membrane as a pattern transfer mask for either the etching of underlying material or for the deposition of additional material onto the surface of a scintillator. Exemplary detectors utilizing such photonic crystal scintillators are also provided.

  9. All-silica, large mode area, single mode photonic bandgap fibre with Fabry-Perot resonant structures

    NASA Astrophysics Data System (ADS)

    Várallyay, Zoltán; Kovács, Péter

    2016-03-01

    All-silica, photonic crystal fibres consisting of a low index, silica core surrounded by higher index inclusions embedded in a silica matrix to form a photonic bandgap cladding were numerically analysed. The aim of the investigations was to modify the guiding properties of the fibre by introducing resonant structural entities. These structural modifications are realised by altering the refractive index of certain high index inclusions in the photonic crystal cladding resulting in mode coupling between the core mode and the mode propagated in the modified index region. This results in an increased effective core area of the fundamental core mode and consequently decreased nonlinearity as well as modified effective index compared to the effective index of the unmodified structure and resonant dispersion profile that can be used for pulse compression or optical delay purposes.

  10. Photonic crystal technology for terahertz system integration

    NASA Astrophysics Data System (ADS)

    Fujita, Masayuki; Nagatsuma, Tadao

    2016-04-01

    Developing terahertz integration technology is essential for practical use of terahertz electromagnetic waves (0.1-10 THz) in various applications including broadband wireless communication, spectroscopic sensing, and nondestructive imaging. In this paper, we present our recent challenges towards terahertz system integration based on photonic crystal technology such as the development of terahertz transceivers. We use photonic-crystal slabs consisting of a twodimensional lattice of air holes formed in a silicon slab to develop low loss compact terahertz components in planar structures. The demonstration of ultralow loss (< 0.1 dB/cm) waveguides and integrated transceiver devices in the 0.3 THz band shows the potential for the application of photonic crystals to terahertz integration technology. Improving the coupling efficiency between the photonic crystal waveguide and resonant tunneling diode is important to take full advantage of the ultralow loss photonic crystal waveguides.

  11. Surface states in photonic crystals

    NASA Astrophysics Data System (ADS)

    Vojtíšek, P.; Richter, I.

    2013-04-01

    Among many unusual and interesting physical properties of photonic crystals (PhC), in recent years, the propagation of surface electromagnetic waves along dielectric PhC boundaries have attracted considerable attention, also in connection to their possible applications. Such surfaces states, produced with the help of specialized defects on PhC boundaries, similarly to surfaces plasmons, are localized surfaces waves and, as such, can be used in various sensing applications. In this contribution, we present our recent studies on numerical modelling of surface states (SS) for all three cases of PhC dimensionality. Simulations of these states were carried out by the use of plane wave expansion (PWE) method via the MIT MPB package.

  12. Liquid crystal orientation control in photonic liquid crystal fibers

    NASA Astrophysics Data System (ADS)

    Chychlowski, M. S.; Nowinowski-Kruszelnicki, E.; Woliński, T. R.

    2011-05-01

    Similarly to liquid crystal displays technology in photonic liquid crystal fibers (PLCFs) a molecular orientation control is a crucial issue that influences proper operation of PLCF-based devices. The paper presents two distinct configurations: planar and radial escaped orientation of the LC molecules inside capillaries as well as methods of their application to photonic liquid crystal fibers. Possibilities of LC orientation control influence both: attenuation and transmitting spectra of the PLCF The orienting method is based on creation of an additional orienting layer on the inner surface of the capillary or air hole of the photonic liquid crystal fiber. Aligning materials used in the experiment are commercially available polyimides SE1211 and SE130 which induce liquid crystal homeotropic and planar anchoring conditions. The orienting layer increase an order parameter of the liquid crystal improving propagation properties and stability of photonic liquid crystal fiber-based devices.

  13. Butterfly wing color: A photonic crystal demonstration

    NASA Astrophysics Data System (ADS)

    Proietti Zaccaria, Remo

    2016-01-01

    We have theoretically modeled the optical behavior of a natural occurring photonic crystal, as defined by the geometrical characteristics of the Teinopalpus Imperialis butterfly. In particular, following a genetic algorithm approach, we demonstrate how its wings follow a triclinic crystal geometry with a tetrahedron unit base. By performing both photonic band analysis and transmission/reflection simulations, we are able to explain the characteristic colors emerging by the butterfly wings, thus confirming their crystal form.

  14. Dispersion properties of transverse anisotropic liquid crystal core photonic crystal fibers

    NASA Astrophysics Data System (ADS)

    Karasawa, Naoki

    2016-04-01

    The dispersion properties of liquid crystal core photonic crystal fibers for different core diameters have been calculated by a full vectorial finite difference method. In calculations, air holes are assumed to be arranged in a regular hexagonal array in fused silica and a central hole is filled with liquid crystal to create a core. In this study, three types of transverse anisotropic configurations, where liquid crystal molecules are oriented in a transverse plane, and a planar configuration, where liquid crystal molecules are oriented in a propagation direction, are considered. The large changes of the dispersion properties are found when the orientation of the liquid crystal molecules is changed from a planar configuration to a uniform configuration, where all molecules are oriented in the same direction in a transverse plane. Since the orientation of liquid crystal molecules may be controlled by applying an electric field, it could be utilized for various applications including the spectral control of supercontinuum generation.

  15. On-chip generation and demultiplexing of quantum correlated photons using a silicon-silica monolithic photonic integration platform.

    PubMed

    Matsuda, Nobuyuki; Karkus, Peter; Nishi, Hidetaka; Tsuchizawa, Tai; Munro, William J; Takesue, Hiroki; Yamada, Koji

    2014-09-22

    We demonstrate the generation and demultiplexing of quantum correlated photons on a monolithic photonic chip composed of silicon and silica-based waveguides. Photon pairs generated in a nonlinear silicon waveguide are successfully separated into two optical channels of an arrayed-waveguide grating fabricated on a silica-based waveguide platform.

  16. Photonic crystal microcavity lasers and laser arrays

    NASA Astrophysics Data System (ADS)

    Cao, Jiang-Rong

    As a state-of-the-art technology, photonic crystal microcavity lasers have great potentials to resolve many semiconductor laser performance challenges, owing to their compact size, high spontaneous emission factor, and inherent advantages in dimension scalability. This thesis describes efficient numerical analyzing methods for multimode photonic crystal microcavities, including a parallel computing three-dimensional finite-difference time-domain method combined with Pade interpolation, point group projection, and vectorial Green's function method. With the help of these analyzing tools, various experimental photonic crystal microcavity devices fabricated in InGaAsP/InP based materials were studies. Room temperature optical pumped InGaAsP suspended membrane photonic crystal microcavity lasers were demonstrated. Their lithographical fine-tuning, above room temperature operations, mode identifications and polarizations were demonstrated. Room temperature continuous wave (CW) optically pumped photonic crystal microcavity lasers at diameter less than 3.2 mum were demonstrated with crystalline alpha-Al 2O3 (sapphire) as a cladding layer to the InGaAsP membrane. The far-field radiation profiles from these microcavity lasers were measured and compared with our numerical modeling predictions. Two electrical injection scenes for photonic crystal microcavity lasers were introduced, together with some preliminary results including the demonstrations of optically pumped lasing of highly doped cavities and cavities with an electrical conduction post underneath. Electrically excited photonic crystal microcavity light emitting diodes (LEDs) were also experimentally demonstrated.

  17. Quantum Cascade Photonic Crystal lasers

    NASA Astrophysics Data System (ADS)

    Capasso, Federico

    2004-03-01

    QC lasers have emerged in recent years as the dominant laser technology for the mid-to far infrared spectrum in light of their room temperature operation, their tunability, ultrahigh speed operation and broad range of applications to chemical sensing, spectroscopy etc. (Ref. 1-3). After briefly reviewing the latter, I will describe a new class of mid-infrared QC lasers, Quantum Cascade Photonic Crystal Surface Emitting Lasers (QCPCSELS), that combine electronic and photonic band structure engineering to achieve vertical emission from the surface (Ref. 4). Devices operating on bandedge mode and on defect modes will be discussed. Exciting potential uses of these new devices exist in nonlinear optics, microfluidics as well as novel sensors. Finally a bird's eye view of other exciting areas of QC laser research will be given including broadband QCLs and new nonlinear optical sources based on multiwavelength QCLs. 1. F. Capasso, C. Gmachl, D. L. Sivco, and A. Y. Cho, Physics Today 55, 34 (May 2002) 2. F. Capasso, C. Gmachl, R. Paiella, A. Tredicucci, A. L. Hutchinson, D. L. Sivco, J. N. Baillargeon, A. Y. Cho and H. C. Liu, IEEE Journal of Selected Topics in Quantum Electronics, 6, 931 (2000). 3. F. Capasso, R. Paiella, R. Martini, R. Colombelli, C. Gmachl, T. L. Myers, M. S. Taubman, R. M. Williams, C. G. Bethea, K. Unterrainer, H. Y. Hwang, D. L. Sivco, A. Y. Cho, A. M. Sergent, H. C. Liu, E. A. Whittaker, IEEE J. Quantum Electron. 38, 511 (2002) 4. R. Colombelli, K. Srivasan, M. Troccoli, O. Painter, C. Gmachl, D. M. Tennant, A. M. Sergent, D. L. Sivco, A. Y. Cho and F. Capasso, Science 302, 1374 (2003)

  18. Novel photonic crystal cavities and related structures.

    SciTech Connect

    Luk, Ting Shan

    2007-11-01

    The key accomplishment of this project is to achieve a much more in-depth understanding of the thermal emission physics of metallic photonic crystal through theoretical modeling and experimental measurements. An improved transfer matrix technique was developed to enable incorporation of complex dielectric function. Together with microscopic theory describing emitter radiative and non-radiative relaxation dynamics, a non-equilibrium thermal emission model is developed. Finally, experimental methodology was developed to measure absolute emissivity of photonic crystal at high temperatures with accuracy of +/-2%. Accurate emissivity measurements allow us to validate the procedure to treat the effect of the photonic crystal substrate.

  19. Electromechanically tunable carbon nanofiber photonic crystal.

    PubMed

    Rehammar, Robert; Ghavanini, Farzan Alavian; Magnusson, Roger; Kinaret, Jari M; Enoksson, Peter; Arwin, Hans; Campbell, Eleanor E B

    2013-02-13

    We demonstrate an electrically tunable 2D photonic crystal array constructed from vertically aligned carbon nanofibers. The nanofibers are actuated by applying a voltage between adjacent carbon nanofiber pairs grown directly on metal electrodes, thus dynamically changing the form factor of the photonic crystal lattice. The change in optical properties is characterized using optical diffraction and ellipsometry. The experimental results are shown to be in agreement with theoretical predictions and provide a proof-of-principle for rapidly switchable photonic crystals operating in the visible that can be fabricated using standard nanolithography techniques combined with plasma CVD growth of the nanofibers.

  20. Structural characterization of thin film photonic crystals

    SciTech Connect

    Subramania, G.; Biswas, R.; Constant, K.; Sigalas, M. M.; Ho, K. M.

    2001-06-15

    We quantitatively analyze the structure of thin film inverse-opal photonic crystals composed of ordered arrays of air pores in a background of titania. Ordering of the sphere template and introduction of the titania background were performed simultaneously in the thin film photonic crystals. Nondestructive optical measurements of backfilling with high refractive index liquids, angle-resolved reflectivity, and optical spectroscopy were combined with band-structure calculations. The analysis reveals a thin film photonic crystal structure with a very high filling fraction (92{endash}94%) of air and a substantial compression along the c axis ({similar_to}22{endash}25%).

  1. Synthesis and photonic band calculations of NCP face-centered cubic photonic crystals of TiO2 hollow spheres.

    PubMed

    Zhu, Yong-zheng; Cao, Yan-ling; Li, Zhi-hui; Ding, Juan; Liu, Jun-song; Chi, Yuan-bin

    2007-02-01

    With the help of self-assembly, thermal sintering, selective etching techniques and sol-gel process, the non-close packed (ncp) face-centered cubic (fcc) photonic crystals of titanium dioxide (TiO2) hollow spheres connected by TiO2 cylindrical tubes have been fabricated using silica template. The photonic bandgap calculations indicate that the ncp structure of TiO2 hollow spheres was easier to open the pseudogaps than close packed system at the lowest energy.

  2. Tunable photonic Bloch oscillations in electrically modulated photonic crystals.

    PubMed

    Wang, Gang; Huang, Ji Ping; Yu, Kin Wah

    2008-10-01

    We exploit theoretically the occurrence and tunability of photonic Bloch oscillations (PBOs) in one-dimensional photonic crystals (PCs) containing nonlinear composites. Because of the enhanced third-order nonlinearity (Kerr-type nonlinearity) of composites, photons undergo oscillations inside tilted photonic bands, which are achieved by the application of graded external-pump electric fields on such PCs, varying along the direction perpendicular to the surface of layers. The tunability of PBOs (including amplitude and period) is readily achieved by changing the field gradient. With an appropriate graded pump ac or dc electric field, terahertz PBOs can appear and cover a terahertz band in an electromagnetic spectrum.

  3. Advanced Integrated Photonics in Doped Silica Glass

    NASA Astrophysics Data System (ADS)

    Ferrera, Marcello; Duchesne, David; Razzari, L.; Peccianti, Marco; Pasquazi, Alessia; Park, Yong-Woo; Azaña, Jose; Morandotti, Roberto; Little, Brent E.; Chu, Sai T.; Moss, David J.

    Broadband optical communication systems are rapidly becoming the key to overcome the stringent limitations imposed by standard electronic telecommunication networks. However, in order to complete the inevitable transition from electronics to photonics, several critical requirements must be addressed, including lowering energetic demands, achieving higher efficiency, increasing bandwidth and flexibility, all within a compact form factor [1-3]. In particular, it is broadly accepted that future photonic devices must be CMOS compatible in order to exploit the existing silicon fabrication technology that has been largely developed during the last 60 years [4-7]. Following this idea, there has been a tremendous growth of hybrid optoelectronic technologies that has not only responded to the need of lowering costs, but has also enabled on-chip ultra-fast signal processing. However, these hybrid solutions are an intermediate step to achieve the ambitious goal of an all-optical technology, which would bring together the intrinsic benefit of lowering the production costs and simplifying future ultrafast communication networks.

  4. Synthesis and Characterization of Opal-Like Photonic Crystals Using Combined Methods

    NASA Astrophysics Data System (ADS)

    Akhmadeev, A. A.; Salakhov, M. Kh.

    2015-09-01

    We investigate the influence of various factors on the synthesis of photonic crystals. These materials are promising for the creation of various devices, as well as for the observation of new effects due to their unique properties. Photonic crystals were synthesized by selfassembly of colloidal silica particles with low deviation in size. The parameters of the photonic crystals were investigated by complementary techniques, including atomic force microscopy, optical spectrophotometry and other methods. It is shown that the measurement accuracy increases with the combined use of these techniques; the results of the study allow us to obtain samples with the desired properties.

  5. Sensitivity enhancement in photonic crystal slab biosensors.

    PubMed

    El Beheiry, Mohamed; Liu, Victor; Fan, Shanhui; Levi, Ofer

    2010-10-25

    Refractive index sensitivity of guided resonances in photonic crystal slabs is analyzed. We show that modal properties of guided resonances strongly affect spectral sensitivity and quality factors, resulting in substantial enhancement of refractive index sensitivity. A three-fold spectral sensitivity enhancement is demonstrated for suspended slab designs, in contrast to designs with a slab resting over a substrate. Spectral sensitivity values are additionally shown to be unaffected by quality factor reductions, which are common to fabricated photonic crystal nano-structures. Finally, we determine that proper selection of photonic crystal slab design parameters permits biosensing of a wide range of analytes, including proteins, antigens, and cells. These photonic crystals are compatible with large-area biosensor designs, permitting direct access to externally incident optical beams in a microfluidic device.

  6. Photonic crystal: energy-related applications

    SciTech Connect

    Ye, Zhuo; Park, Joong-Mok; Constant, Kristen; Kim, Tae-Geun; Ho, Kai-Ming

    2012-06-08

    We review recent work on photonic-crystal fabrication using soft-lithography techniques. We consider applications of the resulting structures in energy-related areas such as lighting and solar-energy harvesting. In general, our aim is to introduce the reader to the concepts of photonic crystals, describe their history, development, and fabrication techniques and discuss a selection of energy-related applications.

  7. Metallic photonic crystals for thermophotovoltaic applications

    NASA Astrophysics Data System (ADS)

    Walsh, Timothy A.

    Since the idea of a photonic bandgap was proposed over two decades ago, photonic crystals have been the subject of significant interest due to their novel optical properties which enable new and varied applications. In this research, the photonic bandgap effect is exploited to tailor the thermal radiation spectrum to a narrow range of wavelengths determined by the lattice symmetry and dimensions of the photonic crystal structure. This sharp emission peak can be matched to the electronic bandgap energy of a p-n junction photovoltaic cell for high efficiency thermophotovoltaic energy conversion. This thesis explores aspects of photonic crystal design, materials considerations, and manufacture for thermophotovoltaic applications. Photonic crystal structures come in many forms, exhibiting various types of 1D, 2D, and 3D lattice symmetry. In this work, the "woodpile" 3D photonic crystal is studied. One advantage of the woodpile lattice is that it can be readily fabricated on a large scale using common integrated circuit manufacturing techniques. Additionally this structure lends itself to efficient and accurate modeling with the use of a plane-wave expansion based transfer matrix method to calculate the scattering properties and band structure of the photonic crystal. This method is used to explore the geometric design parameters of the woodpile structure. Optimal geometric proportions for the structure are found which yield the highest narrowband absorption peak possible. By Kirchoffs law of thermal emission, this strong and sharp absorptance will yield high power and narrowband thermal radiation. The photonic crystal thermal emission spectrum is then evaluated in a TPV system model to evaluate the electrical power density and system efficiency achievable. The results produced by the photonic crystal emitter are compared with the results assuming a blackbody thermal radiation spectrum. The blackbody represents a universal standard against which any selective emitter

  8. Photonic crystal waveguide created by selective infiltration

    NASA Astrophysics Data System (ADS)

    Casas Bedoya, A.; Domachuk, P.; Grillet, C.; Monat, C.; Mägi, E. C.; Li, E.; Eggleton, B. J.

    2012-06-01

    The marriage of photonics and microfluidics ("optofluidics") uses the inherent mobility of fluids to reversibly tune photonic structures beyond traditional fabrication methods by infiltrating voids in said structures. Photonic crystals (PhCs) strongly control light on the wavelength scale and are well suited to optofluidic tuning because their periodic airhole microstructure is a natural candidate for housing liquids. The infiltration of a single row of holes in the PhC matrix modifies the effective refractive index allowing optical modes to be guided by the PhC bandgap. In this work we present the first experimental demonstration of a reconfigurable single mode W1 photonic crystal defect waveguide created by selective liquid infiltration. We modified a hexagonal silicon planar photonic crystal membrane by selectively filling a single row of air holes with ~300nm resolution, using high refractive index ionic liquid. The modification creates optical confinement in the infiltrated region and allows propagation of a single optical waveguide mode. We describe the challenges arising from the infiltration process and the liquid/solid surface interaction in the photonic crystal. We include a detailed comparison between analytic and numerical modeling and experimental results, and introduce a new approach to create an offset photonic crystal cavity by varying the nature of the selective infiltration process.

  9. Optical trapping apparatus, methods and applications using photonic crystal resonators

    SciTech Connect

    Erickson, David; Chen, Yih-Fan

    2015-06-16

    A plurality of photonic crystal resonator optical trapping apparatuses and a plurality optical trapping methods using the plurality of photonic crystal resonator optical trapping apparatuses include located and formed over a substrate a photonic waveguide that is coupled (i.e., either separately coupled or integrally coupled) with a photonic crystal resonator. In a particular embodiment, the photonic waveguide and the photonic crystal resonator comprise a monocrystalline silicon (or other) photonic material absent any chemical functionalization. In another particular embodiment, the photonic waveguide and the photonic crystal resonator comprise a silicon nitride material which when actuating the photonic crystal resonator optical trapping apparatus with a 1064 nanometer resonant photonic radiation wavelength (or other resonant photonic radiation wavelength in a range from about 700 to about 1200 nanometers) provides no appreciable heating of an aqueous sample fluid that is analyzed by the photonic crystal resonator optical trapping apparatus.

  10. Efficient low-temperature thermophotovoltaic emitters from metallic photonic crystals.

    PubMed

    Nagpal, Prashant; Han, Sang Eon; Stein, Andreas; Norris, David J

    2008-10-01

    We examine the use of metallic photonic crystals as thermophotovoltaic emitters. We coat silica woodpile structures, created using direct laser writing, with tungsten or molybdenum. Optical reflectivity and thermal emission measurements near 650 degrees C demonstrate that the resulting structures should provide efficient emitters at relatively low temperatures. When matched to InGaAsSb photocells, our structures should generate over ten times more power than solid emitters while having an optical-to-electrical conversion efficiency above 32%. At such low temperatures, these emitters have promise not only in solar energy but also in harnessing geothermal and industrial waste heat.

  11. Surface-enhanced Raman scattering on diatom biosilica photonic crystals

    NASA Astrophysics Data System (ADS)

    Ren, Fanghui; Campbell, Jeremy; Hasan, Dihan; Wang, Xiangyu; Rorrer, Gregory L.; Wang, Alan X.

    Diatoms are a group of single-celled photosynthetic algae that make skeletal shells of hydrated amorphous silica, called frustules, which possess hierarchical nanoscale photonic crystal features made by a bottom-up approach at ambient temperature and pressure. In this paper, we theoretically investigate electric field enhancements of plasmonic nanoparticles coated on the surface of diatom skeletal shells. Surface-Enhanced Raman Scattering substrates are prepared by evaporating 10 nm thick silver film and self-assembling silver nanoparticles on diatom surfaces, which show significantly better SERS signals than silver nanoparticles on flat glass substrates.

  12. Controlling spontaneous emission in bioreplica photonic crystals

    NASA Astrophysics Data System (ADS)

    Jorgensen, Matthew R.; Butler, Elizabeth S.; Bartl, Michael H.

    2012-04-01

    Sophisticated methods have been created by nature to produce structure-based colors as a way to address the need of a wide variety of organisms. This pallet of available structures presents a unique opportunity for the investigation of new photonic crystal designs. Low-temperature sol-gel biotemplating methods were used to transform a single biotemplate into a variety of inorganic oxide structures. The density of optical states was calculated for a diamond-based natural photonic crystal, as well as several structures templated from it. Calculations were experimentally probed by spontaneous emission studies using time correlated single photon counting measurements.

  13. Kagome hollow-core photonic crystal fiber probe for Raman spectroscopy.

    PubMed

    Ghenuche, Petru; Rammler, Silke; Joly, Nicolas Y; Scharrer, Michael; Frosz, Michael; Wenger, Jérôme; Russell, Philip St J; Rigneault, Hervé

    2012-11-01

    We demonstrate the use of a large-pitch Kagome-lattice hollow-core photonic crystal fiber probe for Raman spectroscopy. The large transmission bandwidth of the fiber enables both the excitation and Raman beams to be transmitted through the same fiber. As the excitation beam is mainly transmitted through air inside the hollow core, the silica luminescence background is reduced by over 2 orders of magnitude as compared to standard silica fiber probes, removing the need for fiber background subtraction.

  14. A Three-Dimensional Optical Photonic Crystal

    SciTech Connect

    Fleming, J.G.; Lin, S.

    1998-12-17

    The search for a photonic crystal to confine optical waves in all three dimensions (3D) has proven to be a formidable task. It evolves from an early theoretical suggestion [1,2], a brief skepticism [3-5] and triumph in developing the mm-wave [6-8] and infrared 3D photonic crystals [9]. Yet, the challenge remains, as the ultimate goal for optoelectronic applications is to realize a 3D crystal at X=1.5 pm communication wavelengths. Operating at visible and near infrared wavelengths, X=1-2 pm, a photonic crystal may enhance the spontaneous emission rate [1, 10] and give rise to a semiconductor lasers with a zero lasing threshold[11, 12]. Another important application is optically switching, routing and interconnecting light [13,14] with an ultrafast transmission speed of terabits per second. A photonic crystal may also serve as a platform for integrating an all-optical circuitry with multiple photonic components, such as waveguides and switches, built on one chip [15]. In this Letter, we report on the successful fabrication of a working 3D crystal operating at optical L The minimum feature size of the 3D structure is 180 nanometers. The 3D crystal is free from defects over the entire 6-inch silicon wafer and has an absolute photonic band gap centered at A.-1.6 pm. Our data provides the first conclusive evidence for the existence of a full 3D photonic band gap in optical A. This development will pave the way to tinier, cheaper, more effective waveguides, optical switches and lasers.

  15. Progress in 2D photonic crystal Fano resonance photonics

    NASA Astrophysics Data System (ADS)

    Zhou, Weidong; Zhao, Deyin; Shuai, Yi-Chen; Yang, Hongjun; Chuwongin, Santhad; Chadha, Arvinder; Seo, Jung-Hun; Wang, Ken X.; Liu, Victor; Ma, Zhenqiang; Fan, Shanhui

    2014-01-01

    In contrast to a conventional symmetric Lorentzian resonance, Fano resonance is predominantly used to describe asymmetric-shaped resonances, which arise from the constructive and destructive interference of discrete resonance states with broadband continuum states. This phenomenon and the underlying mechanisms, being common and ubiquitous in many realms of physical sciences, can be found in a wide variety of nanophotonic structures and quantum systems, such as quantum dots, photonic crystals, plasmonics, and metamaterials. The asymmetric and steep dispersion of the Fano resonance profile promises applications for a wide range of photonic devices, such as optical filters, switches, sensors, broadband reflectors, lasers, detectors, slow-light and non-linear devices, etc. With advances in nanotechnology, impressive progress has been made in the emerging field of nanophotonic structures. One of the most attractive nanophotonic structures for integrated photonics is the two-dimensional photonic crystal slab (2D PCS), which can be integrated into a wide range of photonic devices. The objective of this manuscript is to provide an in depth review of the progress made in the general area of Fano resonance photonics, focusing on the photonic devices based on 2D PCS structures. General discussions are provided on the origins and characteristics of Fano resonances in 2D PCSs. A nanomembrane transfer printing fabrication technique is also reviewed, which is critical for the heterogeneous integrated Fano resonance photonics. The majority of the remaining sections review progress made on various photonic devices and structures, such as high quality factor filters, membrane reflectors, membrane lasers, detectors and sensors, as well as structures and phenomena related to Fano resonance slow light effect, nonlinearity, and optical forces in coupled PCSs. It is expected that further advances in the field will lead to more significant advances towards 3D integrated photonics, flat

  16. Thermal tunability of photonic bandgaps in liquid crystal filled polymer photonic crystal fiber

    NASA Astrophysics Data System (ADS)

    Wang, Doudou; Chen, Guoxiang; Wang, Lili

    2016-05-01

    A highly tunable bandgap-guiding polymer photonic crystal fiber is designed by infiltrating the cladding air holes with liquid crystal 5CB. Structural parameter dependence and thermal tunability of the photonic bandgaps, mode properties and confinement losses of the designed fiber are investigated. Bandgaps red shift as the temperature goes up. Average thermal tuning sensitivity of 30.9 nm/°C and 20.6 nm/°C is achieved around room temperature for the first and second photonic bandgap, respectively. Our results provide theoretical references for applications of polymer photonic crystal fiber in sensing and tunable fiber-optic devices.

  17. Liquid crystal devices for photonics applications

    NASA Astrophysics Data System (ADS)

    Chigrinov, Vladimir G.

    2007-11-01

    Liquid crystal (LC) devices for Photonics applications is a hot topic of research. Such elements begin to appear in Photonics market. Passive elements for fiber optical communication systems (DWDM components) based on LC cells can successfully compete with the other elements used for the purpose, such as micro electromechanical (MEM), thermo-optical, opto-mechanical or acousto-optical devices. Application of nematic and ferroelectric LC for high speed communication systems, producing elements that are extremely fast, stable, durable, of low loss, operable over a wide temperature range, and that require small operating voltages and extremely low power consumption. The known LC applications in fiber optics enable to produce switches, filters, attenuators, equalizers, polarization controllers, phase emulators and other fiber optical components. Good robustness due to the absence of moving parts and compatibility with VLSI technology, excellent parameters in a large photonic wavelength range, whereas the complexity of the design and the cost of the device are equivalent to regular passive matrix LC displays makes LC fiber optical devices very attractive for mass production. We have already successfully fabricated certain prototypes of the optical switches based on ferroelectric and nematic LC materials. The electrooptical modes used for the purpose included the light polarization rotation, voltage controllable diffraction and fast switching of the LC refractive index. We used the powerful software to optimize the LC modulation characteristics. Use of photo-alignment technique pioneered by us makes it possible to develop new LC fiber components. Almost all the criteria of perfect LC alignment are met in case of azo-dye layers. We have already used azo-dye materials to align LC in superthin photonic holes, curved and 3D surfaces and as cladding layers in microring silicon based resonators. The prototypes of new LC efficient Photonics devices are envisaged. Controllable

  18. Photonic crystals with active organic materials

    NASA Astrophysics Data System (ADS)

    Wu, Yeheng

    The concept of photonic crystals, which involves periodically arranged dielectrics that form a new type of material having novel photonic properties, was first proposed about two decades ago. Since then, a number of applications in photonic technology have been explored. Specifically, organic and hybrid photonic crystals are promising because of the unique advantages of the organic materials. A one-dimensional (1D) photonic crystal (multilayer) has high reflectance across a certain wavelength range. We report on studies of 1D multilayer polymer films that were fabricated using spin-coating, free film stacking, and co-extrusion techniques. For example, a stack fabricated by placing a laser dye-doped gain medium between two multilayer reflecting polymer films forms a micro-resonator laser or distributed Bragg laser. The resulting laser system is made entirely of plastic and is only several tens of micrometers in thickness. When the gain, a dye-doped medium, comprises one type of a two-type multilayer film, it results a laser exhibiting distributed feedback. At the edge of the photonic band, the group velocity becomes small and the density of photon states becomes high, which leads to laser emission. Such distributed feedback lasers were fabricated using the co-extrusion technique. The refractive indices and the photonic lattice determine the photonic band gap, which can be tuned by changing these parameters. Materials with Kerr nonlinearity exhibit a change in refractive index depending on the incident intensity of the light. To demonstrate such switching, electrochemical etching techniques on silicon wafers were used to form two-dimensional (2D) photonic crystals. By incorporating the nonlinear organic material into the 2D structure, we have made all-optical switches. The reflection of a beam from the 2D photonic crystal can be controlled by another beam because it induces a refractive index change in the active material by altering the reflection band. A mid

  19. Design of photonic crystal splitters/combiners

    NASA Astrophysics Data System (ADS)

    Kim, Sangin; Park, Ikmo; Lim, Hanjo

    2004-10-01

    Photonic band gap (PBG) structures or photonic crystals have attracted a lot of interest since one of their promising applications is to build compact photonic integrated circuits (PIC). One of key components in PICs is a 1 x 2 optical power splitter or a 2 x 1 combiner. Design of 1 x 2 optical power splitters based on photonic crystal has been investigated by several research groups, but no attention has been paid to the design of 2 x 1 optical combiners. In conventional dielectric waveguide based circuits, optical combiners are obtained just by operating the splitters in the opposite direction and the isolation between two input ports in the combiners is naturally achieved. In photonic crystal based circuits, however, we have found that reciprocal operation of the splitters as combiners will not provide proper isolation between the input ports of the combiners. In this work, microwave-circuit concept has been adopted to obtain isolation between two input ports of the combiner and compact optical power splitters/combiners of good performance have been designed using 2-D photonic crystal. Numerical analysis of the designed splitters/combiners has been performed with the finite-difference time-domain method. The designed splitters/combiners show good isolation between input ports in combiner operation with small return losses.

  20. CMOS compatible high-Q photonic crystal nanocavity fabricated with photolithography on silicon photonic platform.

    PubMed

    Ooka, Yuta; Tetsumoto, Tomohiro; Fushimi, Akihiro; Yoshiki, Wataru; Tanabe, Takasumi

    2015-01-01

    Progress on the fabrication of ultrahigh-Q photonic-crystal nanocavities (PhC-NCs) has revealed the prospect for new applications including silicon Raman lasers that require a strong confinement of light. Among various PhC-NCs, the highest Q has been recorded with silicon. On the other hand, microcavity is one of the basic building blocks in silicon photonics. However, the fusion between PhC-NCs and silicon photonics has yet to be exploited, since PhC-NCs are usually fabricated with electron-beam lithography and require an air-bridge structure. Here we show that a 2D-PhC-NC fabricated with deep-UV photolithography on a silica-clad silicon-on-insulator (SOI) structure will exhibit a high-Q of 2.2 × 10(5) with a mode-volume of ~ 1.7(λ/n)(3). This is the highest Q demonstrated with photolithography. We also show that this device exhibits an efficient thermal diffusion and enables high-speed switching. The demonstration of the photolithographic fabrication of high-Q silica-clad PhC-NCs will open possibility for mass-manufacturing and boost the fusion between silicon photonics and CMOS devices.

  1. CMOS compatible high-Q photonic crystal nanocavity fabricated with photolithography on silicon photonic platform

    PubMed Central

    Ooka, Yuta; Tetsumoto, Tomohiro; Fushimi, Akihiro; Yoshiki, Wataru; Tanabe, Takasumi

    2015-01-01

    Progress on the fabrication of ultrahigh-Q photonic-crystal nanocavities (PhC-NCs) has revealed the prospect for new applications including silicon Raman lasers that require a strong confinement of light. Among various PhC-NCs, the highest Q has been recorded with silicon. On the other hand, microcavity is one of the basic building blocks in silicon photonics. However, the fusion between PhC-NCs and silicon photonics has yet to be exploited, since PhC-NCs are usually fabricated with electron-beam lithography and require an air-bridge structure. Here we show that a 2D-PhC-NC fabricated with deep-UV photolithography on a silica-clad silicon-on-insulator (SOI) structure will exhibit a high-Q of 2.2 × 105 with a mode-volume of ~1.7(λ/n)3. This is the highest Q demonstrated with photolithography. We also show that this device exhibits an efficient thermal diffusion and enables high-speed switching. The demonstration of the photolithographic fabrication of high-Q silica-clad PhC-NCs will open possibility for mass-manufacturing and boost the fusion between silicon photonics and CMOS devices. PMID:26086849

  2. Water-dependent photonic bandgap in silica artificial opals.

    PubMed

    Gallego-Gómez, Francisco; Blanco, Alvaro; Canalejas-Tejero, Victor; López, Cefe

    2011-07-01

    Some characteristics of silica--based structures-like the photonic properties of artificial opals formed by silica spheres--can be greatly affected by the presence of adsorbed water. The reversible modification of the water content of an opal is investigated here by moderate heating (below 300 °C) and measuring in situ the changes in the photonic bandgap. Due to reversible removal of interstitial water, large blueshifts of 30 nm and a bandgap narrowing of 7% are observed. The latter is particularly surprising, because water desorption increases the refractive index contrast, which should lead instead to bandgap broadening. A quantitative explanation of this experiment is provided using a simple model for water distribution in the opal that assumes a nonclose-packed fcc structure. This model further predicts that, at room temperature, about 50% of the interstitial water forms necks between nearest-neighbor spheres, which are separated by 5% of their diameter. Upon heating, dehydration predominantly occurs at the sphere surfaces (in the opal voids), so that above 65 °C the remaining water resides exclusively in the necks. A near-close-packed fcc arrangement is only achieved above 200 °C. The high sensitivity to water changes exhibited by silica opals, even under gentle heating of few degrees, must be taken into account for practical applications. Remarkably, accurate control of the distance between spheres--from 16 to 1 nm--is obtained with temperature. In this study, novel use of the optical properties of the opal is made to infer quantitative information about water distribution within silica beads and dehydration phenomena from simple reflection spectra. Taking advantage of the well-defined opal morphology, this approach offers a simple tool for the straightforward investigation of generic adsorption-desorption phenomena, which might be extrapolated to many other fields involving capillary condensation.

  3. Photon Molecules in Atomic Gases Trapped Near Photonic Crystal Waveguides

    NASA Astrophysics Data System (ADS)

    Douglas, James S.; Caneva, Tommaso; Chang, Darrick E.

    2016-07-01

    Realizing systems that support robust, controlled interactions between individual photons is an exciting frontier of nonlinear optics. To this end, one approach that has emerged recently is to leverage atomic interactions to create strong and spatially nonlocal interactions between photons. In particular, effective photonic interactions have been successfully created via interactions between atoms excited to Rydberg levels. Here, we investigate an alternative approach, in which atomic interactions arise via their common coupling to photonic crystal waveguides. This technique takes advantage of the ability to separately tailor the strength and range of interactions via the dispersion engineering of the structure itself, which can lead to qualitatively new types of phenomena. For example, much of the work on photon-photon interactions relies on the linear optical effect of electromagnetically induced transparency, in combination with the use of interactions to shift optical pulses into or out of the associated transparency window. Here, we identify a large new class of "correlated transparency windows," in which photonic states of a certain number and shape selectively propagate through the system. Through this technique, we show that molecular bound states of photon pairs can be created.

  4. Ultrafast optical switching using photonic molecules in photonic crystal waveguides.

    PubMed

    Zhao, Yanhui; Qian, Chenjiang; Qiu, Kangsheng; Gao, Yunan; Xu, Xiulai

    2015-04-01

    We study the coupling between photonic molecules and waveguides in photonic crystal slab structures using finite-difference time-domain method and coupled mode theory. In a photonic molecule with two cavities, the coupling of cavity modes results in two super-modes with symmetric and anti-symmetric field distributions. When two super-modes are excited simultaneously, the energy of electric field oscillates between the two cavities. To excite and probe the energy oscillation, we integrate photonic molecule with two photonic crystal waveguides. In coupled structure, we find that the quality factors of two super-modes might be different because of different field distributions of super-modes. After optimizing the radii of air holes between two cavities of photonic molecule, nearly equal quality factors of two super-modes are achieved, and coupling strengths between the waveguide modes and two super-modes are almost the same. In this case, complete energy oscillations between two cavities can be obtained with a pumping source in one waveguide, which can be read out by another waveguide. Finally, we demonstrate that the designed structure can be used for ultrafast optical switching with a time scale of a few picoseconds.

  5. Charge Stabilized Crystalline Colloidal Arrays As Templates For Fabrication of Non-Close-Packed Inverted Photonic Crystals

    PubMed Central

    Bohn, Justin J.; Ben-Moshe, Matti; Tikhonov, Alexander; Qu, Dan; Lamont, Daniel N.

    2010-01-01

    We developed a straightforward method to form non close-packed highly ordered fcc direct and inverse opal silica photonic crystals. We utilize an electrostatically self assembled crystalline colloidal array (CCA) template formed by monodisperse, highly charged polystyrene particles. We then polymerize a hydrogel around the CCA (PCCA) and condense the silica to form a highly ordered silica impregnated (siPCCA) photonic crystal. Heating at 450 °C removes the organic polymer leaving a silica inverse opal structure. By altering the colloidal particle concentration we independently control the particle spacing and the wall thickness of the inverse opal photonic crystals. This allows us to control the optical dielectric constant modulation in order to optimize the diffraction; the dielectric constant modulation is controlled independently of the photonic crystal periodicity. These fcc photonic crystals are better ordered than typical close-packed photonic crystals because their self assembly utilizes soft electrostatic repulsive potentials. We show that colloidal particle size and charge polydispersity has modest impact on ordering, in contrast to that for close-packed crystals. PMID:20163800

  6. Photonic quasi-crystal terahertz lasers

    NASA Astrophysics Data System (ADS)

    Vitiello, Miriam Serena; Nobile, Michele; Ronzani, Alberto; Tredicucci, Alessandro; Castellano, Fabrizio; Talora, Valerio; Li, Lianhe; Linfield, Edmund H.; Davies, A. Giles

    2014-12-01

    Quasi-crystal structures do not present a full spatial periodicity but are nevertheless constructed starting from deterministic generation rules. When made of different dielectric materials, they often possess fascinating optical properties, which lie between those of periodic photonic crystals and those of a random arrangement of scatterers. Indeed, they can support extended band-like states with pseudogaps in the energy spectrum, but lacking translational invariance, they also intrinsically feature a pattern of ‘defects’, which can give rise to critically localized modes confined in space, similar to Anderson modes in random structures. If used as laser resonators, photonic quasi-crystals open up design possibilities that are simply not possible in a conventional periodic photonic crystal. In this letter, we exploit the concept of a 2D photonic quasi crystal in an electrically injected laser; specifically, we pattern the top surface of a terahertz quantum-cascade laser with a Penrose tiling of pentagonal rotational symmetry, reaching 0.1-0.2% wall-plug efficiencies and 65 mW peak output powers with characteristic surface-emitting conical beam profiles, result of the rich quasi-crystal Fourier spectrum.

  7. Photonic quasi-crystal terahertz lasers

    PubMed Central

    Vitiello, Miriam Serena; Nobile, Michele; Ronzani, Alberto; Tredicucci, Alessandro; Castellano, Fabrizio; Talora, Valerio; Li, Lianhe; Linfield, Edmund H.; Davies, A. Giles

    2014-01-01

    Quasi-crystal structures do not present a full spatial periodicity but are nevertheless constructed starting from deterministic generation rules. When made of different dielectric materials, they often possess fascinating optical properties, which lie between those of periodic photonic crystals and those of a random arrangement of scatterers. Indeed, they can support extended band-like states with pseudogaps in the energy spectrum, but lacking translational invariance, they also intrinsically feature a pattern of ‘defects’, which can give rise to critically localized modes confined in space, similar to Anderson modes in random structures. If used as laser resonators, photonic quasi-crystals open up design possibilities that are simply not possible in a conventional periodic photonic crystal. In this letter, we exploit the concept of a 2D photonic quasi crystal in an electrically injected laser; specifically, we pattern the top surface of a terahertz quantum-cascade laser with a Penrose tiling of pentagonal rotational symmetry, reaching 0.1–0.2% wall-plug efficiencies and 65 mW peak output powers with characteristic surface-emitting conical beam profiles, result of the rich quasi-crystal Fourier spectrum. PMID:25523102

  8. Growing single crystals in silica gel

    NASA Technical Reports Server (NTRS)

    Rubin, B.

    1970-01-01

    Two types of chemical reactions for crystal growing are discussed. The first is a metathetical reaction to produce calcium tartrate tetrahydrate crystals, the second is a decomplexation reaction to produce cuprous chloride crystals.

  9. Veselago lens by photonic hyper-crystals

    SciTech Connect

    Huang, Zun Narimanov, Evgenii E.

    2014-07-21

    Based on the recent concept of the photonic hyper-crystal—an artificial optical medium that combines the properties of hyperbolic materials and photonic crystals, we present the imaging system functioning as a Veselago lens. This planar lens shows a nearly constant negative refractive index with substantially reduced image aberrations, and can find potential applications in photolithography and hot-spots detection of silicon-based integrated circuits.

  10. Ultra compact spectrometer apparatus and method using photonic crystals

    NASA Technical Reports Server (NTRS)

    Ting, David Z. (Inventor); Hill, Cory J. (Inventor); Bandara, Sumith V. (Inventor); Gunapala, Sarath D. (Inventor)

    2009-01-01

    The present invention is directed to methods of photonic crystal formation, and to methods and apparatus for using such photonic crystals, particularly in conjunction with detector arrays. Photonic crystal parameters and detector array parameters are compared to optimize the selection and orientation of a photonic crystal shape. A photonic crystal is operatively positioned relative to a plurality of light sensors. The light sensors can be separated by a pitch distance and positioned within one half of the pitch distance of an exit surface of the photonic crystals.

  11. Integrated photonic crystal selective emitter for thermophotovoltaics

    NASA Astrophysics Data System (ADS)

    Zhou, Zhiguang; Yehia, Omar; Bermel, Peter

    2016-01-01

    Converting blackbody thermal radiation to electricity via thermophotovoltaics (TPV) is inherently inefficient. Photon recycling using cold-side filters offers potentially improved performance but requires extremely close spacing between the thermal emitter and the receiver, namely a high view factor. Here, we propose an alternative approach for thermal energy conversion, the use of an integrated photonic crystal selective emitter (IPSE), which combines two-dimensional photonic crystal selective emitters and filters into a single device. Finite difference time domain and current transport simulations show that IPSEs can significantly suppress sub-bandgap photons. This increases heat-to-electricity conversion for photonic crystal based emitters from 35.2 up to 41.8% at 1573 K for a GaSb photovoltaic (PV) diode with matched bandgaps of 0.7 eV. The physical basis of this enhancement is a shift from a perturbative to a nonperturbative regime, which maximized photon recycling. Furthermore, combining IPSEs with nonconductive optical waveguides eliminates a key difficulty associated with TPV: the need for precise alignment between the hot selective emitter and cool PV diode. The physical effects of both the IPSE and waveguide can be quantified in terms of an extension of the concept of an effective view factor.

  12. Integrated photonic crystal selective emitter for thermophotovoltaics

    NASA Astrophysics Data System (ADS)

    Zhou, Zhiguang; Yehia, Omar; Bermel, Peter

    2016-01-01

    Converting blackbody thermal radiation to electricity via thermophotovoltaics (TPV) is inherently inefficient. Photon recycling using cold-side filters offers potentially improved performance but requires extremely close spacing between the thermal emitter and the receiver, namely a high view factor. Here, we propose an alternative approach for thermal energy conversion, the use of an integrated photonic crystal selective emitter (IPSE), which combines two-dimensional photonic crystal selective emitters and filters into a single device. Finite difference time domain and current transport simulations show that IPSEs can significantly suppress sub-bandgap photons. This increases heat-to-electricity conversion for photonic crystal based emitters from 35.2 up to 41.8% at 1573 K for a GaSb photovoltaic (PV) diode with matched bandgaps of 0.7 eV. The physical basis of this enhancement is a shift from a perturbative to a nonperturbative regime, which maximized photon recycling. Furthermore, combining IPSEs with nonconductive optical waveguides eliminates a key difficulty associated with TPV: the need for precise alignment between the hot selective emitter and cool PV diode. The physical effects of both the IPSE and waveguide can be quantified in terms of an extension of the concept of an effective view factor.

  13. Self-assembled tunable photonic hyper-crystals

    NASA Astrophysics Data System (ADS)

    Smolyaninov, Igor; Smolyaninova, Vera; Yost, Bradley; Lahneman, David; Gresock, Thomas; Narimanov, Evgenii

    2015-03-01

    We demonstrate a novel artificial optical material, the photonic hyper-crystal, which combines the most interesting features of hyperbolic metamaterials and photonic crystals. Similar to hyperbolic metamaterials, photonic hyper-crystals exhibit broadband divergence in their photonic density of states due to the lack of usual diffraction limit on the photon wave vector. On the other hand, similar to photonic crystals, hyperbolic dispersion law of extraordinary photons is modulated by forbidden gaps near the boundaries of photonic Brillouin zones. Three dimensional self-assembly of photonic hyper-crystals has been achieved by application of external magnetic field to a cobalt nanoparticle-based ferrofluid. Unique spectral properties of photonic hyper-crystals lead to extreme sensitivity of the material to monolayer coatings of cobalt nanoparticles, which should find numerous applications in biological and chemical sensing. This work was supported in part by NSF Grant DMR-1104676, NSF Center for Photonic and Multiscale Nanomaterials, ARO MURI and Gordon and Berry Moore Foundation.

  14. Hybrid photonic-plasmonic crystal nanocavities.

    PubMed

    Yang, Xiaodong; Ishikawa, Atsushi; Yin, Xiaobo; Zhang, Xiang

    2011-04-26

    We propose a hybrid optical nanocavity consisting of photonic crystals coupled to a metal surface with a nanoscale air gap between. The hybridization of photonic crystal modes and surface plasmons across the gap forms hybrid cavity modes, which are highly confined in the low-loss air gap region. Deep subwavelength mode volume and high quality factor are demonstrated at telecommunication wavelength, resulting in an extremely large Q/V(m) ratio of 60,000 λ(-3). This new type of high-Q/V(m) broad-band hybrid nanocavity opens up opportunities for various applications in enhanced light-matter interactions.

  15. Optical amplification enhancement in photonic crystals

    SciTech Connect

    Sapienza, R.; Leonetti, M.; Froufe-Perez, L. S.; Galisteo-Lopez, J. F.; Lopez, C.; Conti, C.

    2011-02-15

    Improving and controlling the efficiency of a gain medium is one of the most challenging problems of laser research. By measuring the gain length in an opal-based photonic crystal doped with laser dye, we demonstrate that optical amplification is more than twenty-fold enhanced along the {Gamma}-K symmetry directions of the face-centered-cubic photonic crystal. These results are theoretically explained by directional variations of the density of states, providing a quantitative connection between density of the states and light amplification.

  16. Two-dimensional photonic crystal surfactant detection.

    PubMed

    Zhang, Jian-Tao; Smith, Natasha; Asher, Sanford A

    2012-08-01

    We developed a novel two-dimensional (2-D) crystalline colloidal array photonic crystal sensing material for the visual detection of amphiphilic molecules in water. A close-packed polystyrene 2-D array monolayer was embedded in a poly(N-isopropylacrylamide) (PNIPAAm)-based hydrogel film. These 2-D photonic crystals placed on a mirror show intense diffraction that enables them to be used for visual determination of analytes. Binding of surfactant molecules attaches ions to the sensor that swells the PNIPAAm-based hydrogel. The resulting increase in particle spacing red shifts the 2-D diffracted light. Incorporation of more hydrophobic monomers increases the sensitivity to surfactants. PMID:22720790

  17. Anomalous reflections at photonic crystal surfaces.

    PubMed

    Yu, Xiaofang; Fan, Shanhui

    2004-11-01

    We explore the reflection phenomena when a light beam propagating in a photonic crystal is incident upon the interfaces between the crystal and a uniform dielectric. We prove that a generalized wave-vector conservation relation still applies even when the interface is not aligned with special crystal directions. Using this conservation relation, we show that neither the phase velocity nor the group velocity directions of the reflected beam satisfies Snell's law. Rather, the system exhibits remarkable and unusual reflection effects. In particular, total internal reflection is absent except at discrete angular values. The direction of the reflected beam can also be pinned along special crystal directions, independent of the orientation of the interface. And finally, at glancing incidences, strong backward reflections may occur. These effects may be important for creating integrated photonic circuits, and for on-chip image transfer.

  18. Fiber based photonic-crystal acoustic sensor

    NASA Astrophysics Data System (ADS)

    Kilic, Onur

    Photonic-crystal slabs are two-dimensional photonic crystals etched into a dielectric layer such as silicon. Standard micro fabrication techniques can be employed to manufacture these structures, which makes it feasible to produce them in large areas, usually an important criterion for practical applications. An appealing feature of these structures is that they can be employed as free-space optical devices such as broadband reflectors. The small thickness of the slab (usually in the vicinity of half a micron) also makes it deflectable. These combined optical and mechanical properties make it possible to employ photonic-crystal slabs in a range of practical applications, including displacement sensors, which in turn can be used for example to detect acoustic waves. An additional benefit of employing a photonic-crystal slab is that it is possible to tailor its optical and mechanical properties by adjusting the geometrical parameters of the structure such as hole radius or shape, pitch, and the slab thickness. By altering the hole radius and pitch, it is possible to make broadband reflectors or sharp transmission filters out of these structures. Adjusting the thickness also affects its deformability, making it possible to make broadband mirrors compliant to acoustic waves. Altering the hole shape, for example by introducing an asymmetry, extends the functionalities of photonic-crystal slabs even further. Breaking the symmetry by introducing asymmetric holes enables polarization-sensitive devices such as retarders, polarization beam splitters, and photonic crystals with additional non-degenerate resonances useful for increased sensitivity in sensors. All these practical advantages of photonic-crystal slabs makes them suitable as key components in micromachined sensor applications. We report one such example of an application of photonic-crystal slabs in the form of a micromachined acoustic sensor. It consists of a Fabry-Perot interferometer made of a photonic-crystal

  19. Wafer-scale plasmonic and photonic crystal sensors

    NASA Astrophysics Data System (ADS)

    George, M. C.; Liu, J.-N.; Farhang, A.; Williamson, B.; Black, M.; Wangensteen, T.; Fraser, J.; Petrova, R.; Cunningham, B. T.

    2015-08-01

    200 mm diameter wafer-scale fabrication, metrology, and optical modeling results are reviewed for surface plasmon resonance (SPR) sensors based on 2-D metallic nano-dome and nano-hole arrays (NHA's) as well as 1-D photonic crystal sensors based on a leaky-waveguide mode resonance effect, with potential applications in label free sensing, surface enhanced Raman spectroscopy (SERS), and surface-enhanced fluorescence spectroscopy (SEFS). Potential markets include micro-arrays for medical diagnostics, forensic testing, environmental monitoring, and food safety. 1-D and 2-D nanostructures were fabricated on glass, fused silica, and silicon wafers using optical lithography and semiconductor processing techniques. Wafer-scale optical metrology results are compared to FDTD modeling and presented along with application-based performance results, including label-free plasmonic and photonic crystal sensing of both surface binding kinetics and bulk refractive index changes. In addition, SEFS and SERS results are presented for 1-D photonic crystal and 2-D metallic nano-array structures. Normal incidence transmittance results for a 550 nm pitch NHA showed good bulk refractive index sensitivity, however an intensity-based design with 665 nm pitch was chosen for use as a compact, label-free sensor at both 650 and 632.8 nm wavelengths. The optimized NHA sensor gives an SPR shift of about 480 nm per refractive index unit when detecting a series of 0-40% glucose solutions, but according to modeling shows about 10 times greater surface sensitivity when operating at 532 nm. Narrow-band photonic crystal resonance sensors showed quality factors over 200, with reasonable wafer-uniformity in terms of both resonance position and peak height.

  20. Self-assembled tunable photonic hyper-crystals.

    PubMed

    Smolyaninova, Vera N; Yost, Bradley; Lahneman, David; Narimanov, Evgenii E; Smolyaninov, Igor I

    2014-01-01

    We demonstrate a novel artificial optical material, the "photonic hyper-crystal", which combines the most interesting features of hyperbolic metamaterials and photonic crystals. Similar to hyperbolic metamaterials, photonic hyper-crystals exhibit broadband divergence in their photonic density of states due to the lack of usual diffraction limit on the photon wave vector. On the other hand, similar to photonic crystals, hyperbolic dispersion law of extraordinary photons is modulated by forbidden gaps near the boundaries of photonic Brillouin zones. Three dimensional self-assembly of photonic hyper-crystals has been achieved by application of external magnetic field to a cobalt nanoparticle-based ferrofluid. Unique spectral properties of photonic hyper-crystals lead to extreme sensitivity of the material to monolayer coatings of cobalt nanoparticles, which should find numerous applications in biological and chemical sensing. PMID:25027947

  1. Self-assembled tunable photonic hyper-crystals

    NASA Astrophysics Data System (ADS)

    Smolyaninova, Vera N.; Yost, Bradley; Lahneman, David; Gresock, Thomas; Narimanov, Evgenii E.; Smolyaninov, Igor I.

    2014-09-01

    We demonstrate a novel artificial optical material, the "photonic hyper-crystal", which combines the most interesting features of hyperbolic metamaterials and photonic crystals. Similar to hyperbolic metamaterials, photonic hyper-crystals exhibit broadband divergence in their photonic density of states due to the lack of usual diffraction limit on the photon wave vector. On the other hand, similar to photonic crystals, hyperbolic dispersion law of extraordinary photons is modulated by forbidden gaps near the boundaries of photonic Brillouin zones. Three dimensional self-assembly of photonic hyper-crystals has been achieved by application of external magnetic field to a cobalt nanoparticle-based ferrofluid. Unique spectral properties of photonic hyper-crystals lead to extreme sensitivity of the material to monolayer coatings of cobalt nanoparticles, which should find numerous applications in biological and chemical sensing.

  2. Self-assembled tunable photonic hyper-crystals

    NASA Astrophysics Data System (ADS)

    Smolyaninova, Vera N.; Yost, Bradley; Lahneman, David; Narimanov, Evgenii E.; Smolyaninov, Igor I.

    2014-07-01

    We demonstrate a novel artificial optical material, the ``photonic hyper-crystal'', which combines the most interesting features of hyperbolic metamaterials and photonic crystals. Similar to hyperbolic metamaterials, photonic hyper-crystals exhibit broadband divergence in their photonic density of states due to the lack of usual diffraction limit on the photon wave vector. On the other hand, similar to photonic crystals, hyperbolic dispersion law of extraordinary photons is modulated by forbidden gaps near the boundaries of photonic Brillouin zones. Three dimensional self-assembly of photonic hyper-crystals has been achieved by application of external magnetic field to a cobalt nanoparticle-based ferrofluid. Unique spectral properties of photonic hyper-crystals lead to extreme sensitivity of the material to monolayer coatings of cobalt nanoparticles, which should find numerous applications in biological and chemical sensing.

  3. Fabrication and Analysis of Photonic Crystals

    ERIC Educational Resources Information Center

    Campbell, Dean J.; Korte, Kylee E.; Xia, Younan

    2007-01-01

    These laboratory experiments are designed to explore aspects of nanoscale chemistry by constructing and spectroscopically analyzing thin films of photonic crystals. Films comprised of colloidal spheres and polydimethylsiloxane exhibit diffraction-based stop bands that shift reversibly upon exposure to some common solvents. Topics covered in these…

  4. Visible stealth materials based on photonic crystals

    NASA Astrophysics Data System (ADS)

    Yao, Guozheng; Liu, Ying

    2014-08-01

    Optical thin film can be used for invisible cloak. As a kind of low-dimension photonic crystal, it is a candidate for metamaterial with designed Σ and μ. As a coating, it is convenient to be stacked to mimic continuous changing of electromagnetic media. Anti-reflection film is suitable for matching coating between layers of media.

  5. Quasicompactons in inverted nonlinear photonic crystals

    SciTech Connect

    Li Yongyao; Malomed, Boris A.; Wu Jianxiong; Pang Wei; Wang Sicong; Zhou Jianying

    2011-10-15

    We study large-amplitude one-dimensional solitary waves in photonic crystals featuring competition between linear and nonlinear lattices, with minima of the linear potential coinciding with maxima of the nonlinear pseudopotential, and vice versa (inverted nonlinear photonic crystals, INPCs), in the case of the saturable self-focusing nonlinearity. Such crystals were recently fabricated using a mixture of SU-8 and Rhodamine-B optical materials. By means of numerical methods and analytical approximations, we find that large-amplitude solitons are broad sharply localized stable pulses (quasicompactons, QCs). With the increase of the total power, P, the QC's centroid performs multiple switchings between minima and maxima of the linear potential. Unlike cubic INPCs, the large-amplitude solitons are mobile in the medium with the saturable nonlinearity. The threshold value of the kick necessary to set the soliton in motion is found as a function of P. Collisions between moving QCs are considered too.

  6. Self-assembled tunable photonic hyper-crystals

    PubMed Central

    Smolyaninova, Vera N.; Yost, Bradley; Lahneman, David; Narimanov, Evgenii E.; Smolyaninov, Igor I.

    2014-01-01

    We demonstrate a novel artificial optical material, the “photonic hyper-crystal”, which combines the most interesting features of hyperbolic metamaterials and photonic crystals. Similar to hyperbolic metamaterials, photonic hyper-crystals exhibit broadband divergence in their photonic density of states due to the lack of usual diffraction limit on the photon wave vector. On the other hand, similar to photonic crystals, hyperbolic dispersion law of extraordinary photons is modulated by forbidden gaps near the boundaries of photonic Brillouin zones. Three dimensional self-assembly of photonic hyper-crystals has been achieved by application of external magnetic field to a cobalt nanoparticle-based ferrofluid. Unique spectral properties of photonic hyper-crystals lead to extreme sensitivity of the material to monolayer coatings of cobalt nanoparticles, which should find numerous applications in biological and chemical sensing. PMID:25027947

  7. Flexible single-crystal silicon nanomembrane photonic crystal cavity.

    PubMed

    Xu, Xiaochuan; Subbaraman, Harish; Chakravarty, Swapnajit; Hosseini, Amir; Covey, John; Yu, Yalin; Kwong, David; Zhang, Yang; Lai, Wei-Cheng; Zou, Yi; Lu, Nanshu; Chen, Ray T

    2014-12-23

    Flexible inorganic electronic devices promise numerous applications, especially in fields that could not be covered satisfactorily by conventional rigid devices. Benefits on a similar scale are also foreseeable for silicon photonic components. However, the difficulty in transferring intricate silicon photonic devices has deterred widespread development. In this paper, we demonstrate a flexible single-crystal silicon nanomembrane photonic crystal microcavity through a bonding and substrate removal approach. The transferred cavity shows a quality factor of 2.2×10(4) and could be bent to a curvature of 5 mm radius without deteriorating the performance compared to its counterparts on rigid substrates. A thorough characterization of the device reveals that the resonant wavelength is a linear function of the bending-induced strain. The device also shows a curvature-independent sensitivity to the ambient index variation.

  8. Non-blinking single-photon emitters in silica.

    PubMed

    Rabouw, Freddy T; Cogan, Nicole M B; Berends, Anne C; Stam, Ward van der; Vanmaekelbergh, Daniel; Koenderink, A Femius; Krauss, Todd D; Donega, Celso de Mello

    2016-01-01

    Samples for single-emitter spectroscopy are usually prepared by spin-coating a dilute solution of emitters on a microscope cover slip of silicate based glass (such as quartz). Here, we show that both borosilicate glass and quartz contain intrinsic defect colour centres that fluoresce when excited at 532 nm. In a microscope image the defect emission is indistinguishable from spin-coated emitters. The emission spectrum is characterised by multiple peaks with the main peak between 2.05 and 2.20 eV, most likely due to coupling to a silica vibration with an energy that varies between 160 and 180 meV. The defects are single-photon emitters, do not blink, and have photoluminescence lifetimes of a few nanoseconds. Photoluminescence from such defects may previously have been misinterpreted as originating from single nanocrystal quantum dots. PMID:26892489

  9. Non-blinking single-photon emitters in silica

    PubMed Central

    Rabouw, Freddy T.; Cogan, Nicole M. B.; Berends, Anne C.; Stam, Ward van der; Vanmaekelbergh, Daniel; Koenderink, A. Femius; Krauss, Todd D.; Donega, Celso de Mello

    2016-01-01

    Samples for single-emitter spectroscopy are usually prepared by spin-coating a dilute solution of emitters on a microscope cover slip of silicate based glass (such as quartz). Here, we show that both borosilicate glass and quartz contain intrinsic defect colour centres that fluoresce when excited at 532 nm. In a microscope image the defect emission is indistinguishable from spin-coated emitters. The emission spectrum is characterised by multiple peaks with the main peak between 2.05 and 2.20 eV, most likely due to coupling to a silica vibration with an energy that varies between 160 and 180 meV. The defects are single-photon emitters, do not blink, and have photoluminescence lifetimes of a few nanoseconds. Photoluminescence from such defects may previously have been misinterpreted as originating from single nanocrystal quantum dots. PMID:26892489

  10. Non-blinking single-photon emitters in silica

    NASA Astrophysics Data System (ADS)

    Rabouw, Freddy T.; Cogan, Nicole M. B.; Berends, Anne C.; Stam, Ward Van Der; Vanmaekelbergh, Daniel; Koenderink, A. Femius; Krauss, Todd D.; Donega, Celso De Mello

    2016-02-01

    Samples for single-emitter spectroscopy are usually prepared by spin-coating a dilute solution of emitters on a microscope cover slip of silicate based glass (such as quartz). Here, we show that both borosilicate glass and quartz contain intrinsic defect colour centres that fluoresce when excited at 532 nm. In a microscope image the defect emission is indistinguishable from spin-coated emitters. The emission spectrum is characterised by multiple peaks with the main peak between 2.05 and 2.20 eV, most likely due to coupling to a silica vibration with an energy that varies between 160 and 180 meV. The defects are single-photon emitters, do not blink, and have photoluminescence lifetimes of a few nanoseconds. Photoluminescence from such defects may previously have been misinterpreted as originating from single nanocrystal quantum dots.

  11. Non-blinking single-photon emitters in silica

    DOE PAGES

    Rabouw, Freddy T.; Cogan, Nicole M. B.; Berends, Anne C.; Stam, Ward van der; Vanmaekelbergh, Daniel; Koenderink, A. Femius; Krauss, Todd D.; Donega, Celso de Mello

    2016-02-19

    Samples for single-emitter spectroscopy are usually prepared by spin-coating a dilute solution of emitters on a microscope cover slip of silicate based glass (such as quartz). Here, we show that both borosilicate glass and quartz contain intrinsic defect colour centres that fluoresce when excited at 532 nm. In a microscope image the defect emission is indistinguishable from spin-coated emitters. The emission spectrum is characterised by multiple peaks with the main peak between 2.05 and 2.20 eV, most likely due to coupling to a silica vibration with an energy that varies between 160 and 180 meV. The defects are single-photon emitters,more » do not blink, and have photoluminescence lifetimes of a few nanoseconds. Furthermore, photoluminescence from such defects may previously have been misinterpreted as originating from single nanocrystal quantum dots.« less

  12. The bifoil photodyne: a photonic crystal oscillator

    NASA Astrophysics Data System (ADS)

    Lugo, J. E.; Doti, R.; Sanchez, N.; de La Mora, M. B.; Del Rio, J. A.; Faubert, J.

    2014-01-01

    Optical tweezers is an example how to use light to generate a physical force. They have been used to levitate viruses, bacteria, cells, and sub cellular organisms. Nonetheless it would be beneficial to use such force to develop a new kind of applications. However the radiation pressure usually is small to think in moving larger objects. Currently, there is some research investigating novel photonic working principles to generate a higher force. Here, we studied theoretically and experimentally the induction of electromagnetic forces in one-dimensional photonic crystals when light impinges on the off-axis direction. The photonic structure consists of a micro-cavity like structure formed of two one-dimensional photonic crystals made of free-standing porous silicon, separated by a variable air gap and the working wavelength is 633 nm. We show experimental evidence of this force when the photonic structure is capable of making auto-oscillations and forced-oscillations. We measured peak displacements and velocities ranging from 2 up to 35 microns and 0.4 up to 2.1 mm/s with a power of 13 mW. Recent evidence showed that giant resonant light forces could induce average velocity values of 0.45 mm/s in microspheres embedded in water with 43 mW light power.

  13. The bifoil photodyne: a photonic crystal oscillator.

    PubMed

    Lugo, J E; Doti, R; Sanchez, N; de la Mora, M B; del Rio, J A; Faubert, J

    2014-01-15

    Optical tweezers is an example how to use light to generate a physical force. They have been used to levitate viruses, bacteria, cells, and sub cellular organisms. Nonetheless it would be beneficial to use such force to develop a new kind of applications. However the radiation pressure usually is small to think in moving larger objects. Currently, there is some research investigating novel photonic working principles to generate a higher force. Here, we studied theoretically and experimentally the induction of electromagnetic forces in one-dimensional photonic crystals when light impinges on the off-axis direction. The photonic structure consists of a micro-cavity like structure formed of two one-dimensional photonic crystals made of free-standing porous silicon, separated by a variable air gap and the working wavelength is 633 nm. We show experimental evidence of this force when the photonic structure is capable of making auto-oscillations and forced-oscillations. We measured peak displacements and velocities ranging from 2 up to 35 microns and 0.4 up to 2.1 mm/s with a power of 13 mW. Recent evidence showed that giant resonant light forces could induce average velocity values of 0.45 mm/s in microspheres embedded in water with 43 mW light power.

  14. The bifoil photodyne: a photonic crystal oscillator

    PubMed Central

    Lugo, J. E.; Doti, R.; Sanchez, N.; de la Mora, M. B.; del Rio, J. A.; Faubert, J.

    2014-01-01

    Optical tweezers is an example how to use light to generate a physical force. They have been used to levitate viruses, bacteria, cells, and sub cellular organisms. Nonetheless it would be beneficial to use such force to develop a new kind of applications. However the radiation pressure usually is small to think in moving larger objects. Currently, there is some research investigating novel photonic working principles to generate a higher force. Here, we studied theoretically and experimentally the induction of electromagnetic forces in one-dimensional photonic crystals when light impinges on the off-axis direction. The photonic structure consists of a micro-cavity like structure formed of two one-dimensional photonic crystals made of free-standing porous silicon, separated by a variable air gap and the working wavelength is 633 nm. We show experimental evidence of this force when the photonic structure is capable of making auto-oscillations and forced-oscillations. We measured peak displacements and velocities ranging from 2 up to 35 microns and 0.4 up to 2.1 mm/s with a power of 13 mW. Recent evidence showed that giant resonant light forces could induce average velocity values of 0.45 mm/s in microspheres embedded in water with 43 mW light power. PMID:24423985

  15. Scanning transmission x-ray microscopy as a novel tool to probe colloidal and photonic crystals.

    PubMed

    van Schooneveld, Matti M; Hilhorst, Jan; Petukhov, Andrei V; Tyliszczak, Tolek; Wang, Jian; Weckhuysen, Bert M; de Groot, Frank M F; de Smit, Emiel

    2011-03-21

    Photonic crystals consisting of nano- to micrometer-sized building blocks, such as multiple sorts of colloids, have recently received widespread attention. It remains a challenge, however, to adequately probe the internal crystal structure and the corresponding deformations that inhibit the proper functioning of such materials. It is shown that scanning transmission X-ray microscopy (STXM) can directly reveal the local structure, orientations, and even deformations in polystyrene and silica colloidal crystals with 30-nm spatial resolution. Moreover, STXM is capable of imaging a diverse range of crystals, including those that are dry and inverted, and provides novel insights complementary to information obtained by benchmark confocal fluorescence and scanning electron microscopy techniques.

  16. Photonic crystal slab quantum cascade detector

    NASA Astrophysics Data System (ADS)

    Reininger, Peter; Schwarz, Benedikt; Harrer, Andreas; Zederbauer, Tobias; Detz, Hermann; Maxwell Andrews, Aaron; Gansch, Roman; Schrenk, Werner; Strasser, Gottfried

    2013-12-01

    In this Letter, we demonstrate the design, fabrication, and characterization of a photonic crystal slab quantum cascade detector (PCS-QCD). By employing a specifically designed resonant cavity, the performance of the photodetector is improved in three distinct ways. The PCS makes the QCD sensitive to surface normal incident light. It resonantly enhances the photon lifetime inside the active zone, thus increasing the photocurrent significantly. And, the construction form of the device inherently decreases the noise. Finally, we compare the characteristics of the PCS-QCD to a PCS - quantum well infrared photodetector and outline the advantages for certain fields of applications.

  17. Photonic crystal slab quantum cascade detector

    SciTech Connect

    Reininger, Peter Schwarz, Benedikt; Harrer, Andreas; Zederbauer, Tobias; Detz, Hermann; Maxwell Andrews, Aaron; Gansch, Roman; Schrenk, Werner; Strasser, Gottfried

    2013-12-09

    In this Letter, we demonstrate the design, fabrication, and characterization of a photonic crystal slab quantum cascade detector (PCS-QCD). By employing a specifically designed resonant cavity, the performance of the photodetector is improved in three distinct ways. The PCS makes the QCD sensitive to surface normal incident light. It resonantly enhances the photon lifetime inside the active zone, thus increasing the photocurrent significantly. And, the construction form of the device inherently decreases the noise. Finally, we compare the characteristics of the PCS-QCD to a PCS - quantum well infrared photodetector and outline the advantages for certain fields of applications.

  18. Photonic crystal electro-optical switching cell

    NASA Astrophysics Data System (ADS)

    Lima, A. Wirth; Sombra, A. S. B.

    2012-06-01

    We investigated the physical mechanism of a photonic crystal (PhC) switching cell based on an optical directional coupler (ODC). This ODC is driven by a low power external electrical command signal, inserted in the central coupling region, which causes the changes in the refractive index. The switching process is based on the change of the bar state to the cross state owing to the external command signal. In our simulations we used the following methods: Plane Wave Expansion by MPB (MIT Photonic-Bands), Finite-Difference Time-Domain by MEEP (MIT Electromagnetic Equation Propagation), Finite Element by COMSOL Multiphysics and our own Binary Propagation Method.

  19. Breakdown of Bose-Einstein Distribution in Photonic Crystals

    PubMed Central

    Lo, Ping-Yuan; Xiong, Heng-Na; Zhang, Wei-Min

    2015-01-01

    In the last two decades, considerable advances have been made in the investigation of nano-photonics in photonic crystals. Previous theoretical investigations of photon dynamics were carried out at zero temperature. Here, we investigate micro/nano cavity photonics in photonic crystals at finite temperature. Due to photonic-band-gap-induced localized long-lived photon dynamics, we discover that cavity photons in photonic crystals do not obey Bose-Einstein statistical distribution. Within the photonic band gap and in the vicinity of the band edge, cavity photons combine the long-lived non-Markovain dynamics with thermal fluctuations together to form photon states that memorize the initial cavity state information. As a result, Bose-Einstein distribution is completely broken down in these regimes, even if the thermal energy is larger or much larger than the cavity detuning energy. In this investigation, a crossover phenomenon from equilibrium to nonequilibrium steady states is also revealed. PMID:25822135

  20. Breakdown of Bose-Einstein distribution in photonic crystals.

    PubMed

    Lo, Ping-Yuan; Xiong, Heng-Na; Zhang, Wei-Min

    2015-01-01

    In the last two decades, considerable advances have been made in the investigation of nano-photonics in photonic crystals. Previous theoretical investigations of photon dynamics were carried out at zero temperature. Here, we investigate micro/nano cavity photonics in photonic crystals at finite temperature. Due to photonic-band-gap-induced localized long-lived photon dynamics, we discover that cavity photons in photonic crystals do not obey Bose-Einstein statistical distribution. Within the photonic band gap and in the vicinity of the band edge, cavity photons combine the long-lived non-Markovain dynamics with thermal fluctuations together to form photon states that memorize the initial cavity state information. As a result, Bose-Einstein distribution is completely broken down in these regimes, even if the thermal energy is larger or much larger than the cavity detuning energy. In this investigation, a crossover phenomenon from equilibrium to nonequilibrium steady states is also revealed.

  1. Prospective effect in dispersion properties of photonic crystal fibers by selective water-filling of holes.

    PubMed

    Ghosh, Prasenjit; Sarkar, Somenath

    2016-01-20

    Based on a simple but accurate semivectorial solution of Helmholtz's equation by the finite difference method devised with a mode-field convergence technique, we have shown an interesting and significant effect showing an almost ultraflat zero group velocity dispersion in photonic crystal fiber when the holes of the first ring of the fiber are filled with water. Crosschecking our results with earlier results involving a deeply involved multipole method for the central core of photonic crystal fiber filled with water and fused silica, our observation in the case of filling the first ring holes with water reveals potential information in studies of supercontinuum generation. PMID:26835922

  2. Amplifying magneto-optical photonic crystal

    NASA Astrophysics Data System (ADS)

    Grishin, A. M.

    2010-08-01

    We modeled transmission and Faraday rotation characteristics of Er-doped all-garnet [Bi3Fe5O12/Gd3Ga5O12]m photonic crystals in view of their application in C-band magneto-optical amplifiers. It is found that 48 layered 11.4 μm thick crystal at λ =1532 nm provides 45° Faraday rotation and transmission as high as 85% being pumped with 100 mW/980 nm solid state laser diode.

  3. Transmission character of general function photonic crystals

    NASA Astrophysics Data System (ADS)

    Wu, Xiang-Yao; Zhang, Bo-Jun; Yang, Jing-Hai; Zhang, Si-Qi; Liu, Xiao-Jing; Wang, Jing; Ba, Nuo; Hua, Zhong; Yin, Xin-Guo

    2012-08-01

    In the paper, we present a new general function photonic crystals (GFPCs), whose refractive index of medium is a arbitrary function of space position. Unlike conventional photonic crystals (PCs), whose structure grows from two mediums A and B, with different constant refractive indexes na and nb. Based on the Fermat principle, we give the motion equations of light in one-dimensional GFPCs, and calculate its transfer matrix, which is different from the conventional PCs. We choose the linearity refractive index function for two mediums A and B, and find the transmissivity of one-dimensional GFPCs can be much larger or smaller than 1 for different slope linearity refractive index functions, which are different from the transmissivity of conventional PCs (its transmissivity is in the range of 0 and 1). Otherwise, we study the effect of different incident angles, the number of periods and optical thickness on the transmissivity, and obtain some new results different from the conventional PCs.

  4. Photonic Crystal Geometry for Organic Solar Cells

    NASA Astrophysics Data System (ADS)

    Samulski, Edward; Lopez, Rene; Ko, Doo-Hyun; Tumbleston, John

    2010-03-01

    Efficient absorption of light calls for thicker PV active layers whereas carrier transport always benefits from thinner ones, and this dichotomy is at the heart of an efficiency/cost conundrum that has kept solar energy expensive relative to fossil fuels. We report a 2-D, photonic crystal morphology that enhances the efficiency of organic photovoltaic cells relative to conventional planar cells.[1] The morphology is developed by patterning an organic photoactive bulk heterojunction blend using PRINT a process that lends itself to large area fabrication of nanostructures.[2] The photonic crystal cell morphology increases photocurrents generally, and particularly through the excitation of resonant modes near the band edge of the organic PV material. [1] Ko, D.-H.; Tumbleston, J. R.; Zhang, L.; Williams, S.; DeSimone, J. M.; Rene, L.; Samulski, E. T. Nano Lett. 2009, 9, 2742--2746. [2] Hampton et al. Adv. Mater. 2008, 20, 2667.

  5. Erbium doped tellurite photonic crystal optical fiber

    NASA Astrophysics Data System (ADS)

    Osorio, Sergio P.; Fernandez, Enver; Rodriguez, Eugenio; Cesar, Carlos L.; Barbosa, Luiz C.

    2005-04-01

    In this work we present the fabrication of tellurite glass photonic crystal fiber doped with a very large erbium concentration. Tellurite glasses are important hosts for rare earth ions due to its very high solubility, which allows up to 10,000 ppm Er3+ concentrations. The photonic crystal optical fibers and tellurite glasses can be, therefore, combined in an efficient way to produce doped fibers for large bandwidth optical amplifiers. The preform was made of a 10 mm external diameter tellurite tube filled with an array of non-periodic tellurite capillaries and an erbium-doped telluride rod that constitute the fiber core. The preform was drawn in a Heathway Drawing Tower, producing fibers with diameters between 120 - 140 μm. We show optical microscope photography of the fiber"s transverse section. The ASE spectra obtained with a spectra analyzer show a red shift as the length of the optical fiber increases.

  6. A tunable microwave plasma photonic crystal filter

    SciTech Connect

    Wang, B.; Cappelli, M. A.

    2015-10-26

    The integration of gaseous plasma elements into a microwave photonic crystal band gap cavity structure allows for active tuning of the device. An alumina rod array microwave photonic crystal waveguide resonator is simulated and characterized through finite difference time domain methods. A gaseous plasma element is integrated into the cavity structure and the effect of plasma density on the transmission properties of the structure is investigated. We show, through both simulations and experiments, that the permittivity of the plasma can be adjusted to shift the peak resonance to allow for both switching and tunability of transmission. The experimentally measured peak shifts in transmission are compared to those simulated and the electron density of the gaseous plasma element is calculated and compared to values determined from the measured discharge current density.

  7. Nonreciprocal photonic crystal add-drop filter

    NASA Astrophysics Data System (ADS)

    Tao, Keyu; Xiao, Jun-Jun; Yin, Xiaobo

    2014-11-01

    We present a versatile add-drop integrated photonic filter (ADF) consisting of nonreciprocal waveguides in which the propagation of light is restricted in one predetermined direction. With the bus and add/drop waveguides symmetrically coupled through a cavity, the four-port device allows each individual port to add and/or drop a signal of the same frequency. The scheme is general and we demonstrate the nonreciprocal ADF with magneto-optical photonic crystals. The filter is immune to waveguide defects, allowing straightforward implementation of multi-channel ADFs by cascading the four-port designs. The results should find applications in wavelength-division multiplexing and related integrated photonic techniques.

  8. Nonreciprocal photonic crystal add-drop filter

    SciTech Connect

    Tao, Keyu; Xiao, Jun-Jun; Yin, Xiaobo

    2014-11-24

    We present a versatile add-drop integrated photonic filter (ADF) consisting of nonreciprocal waveguides in which the propagation of light is restricted in one predetermined direction. With the bus and add/drop waveguides symmetrically coupled through a cavity, the four-port device allows each individual port to add and/or drop a signal of the same frequency. The scheme is general and we demonstrate the nonreciprocal ADF with magneto-optical photonic crystals. The filter is immune to waveguide defects, allowing straightforward implementation of multi-channel ADFs by cascading the four-port designs. The results should find applications in wavelength-division multiplexing and related integrated photonic techniques.

  9. The mechanism of growth of quartz crystals into fused silica

    NASA Technical Reports Server (NTRS)

    Fratello, V. J.; Hays, J. F.; Spaepen, F.; Turnbull, D.

    1980-01-01

    It is proposed that the growth of quartz crystals into fused silica is effected by a mechanism involving the breaking of an Si-O bond and its association with an OH group, followed by cooperative motion of the nonbridging oxygen and the hydroxyl group which results in the crystallization of a row of several molecules along a crystalline-amorphous interfacial ledge. This mechanism explains, at least qualitatively, all the results of the earlier experimental study of the dependence of quartz crystal growth upon applied pressure: large negative activation volume; single activation enthalpy below Si-O bond energy; growth velocity constant in time, proportional to the hydroxyl and chlorine content, decreasing with increasing degree of reduction, and enhanced by nonhydrostatic stresses; lower pre-exponential for the synthetic than for the natural silica.

  10. Photonic Crystal Microcavities for Quantum Information Science

    NASA Astrophysics Data System (ADS)

    Hagemeier, Jenna Nicole

    Quantum information science and technology is a broad and fascinating field, encompassing diverse research areas such as materials science, atomic physics, superconductors, solid-state physics, and photonics. A goal of this field is to demonstrate the basic functions of information initialization, manipulation, and read-out in systems that take advantage of quantum physics to greatly enhance computing performance capabilities. In a hybrid quantum information network, different systems are used to perform different functions, to best exploit the advantageous properties of each system. For example, matter quantum bits (qubits) can be used for local data storage and manipulation while photonic qubits can be used for long-distance communication between storage points of the network. Our research focuses on the following two solid-state realizations of a matter qubit for the purpose of building such a hybrid quantum network: the electronic spin of a self-assembled indium arsenide quantum dot and the electronic spin of a nitrogen-vacancy defect center in diamond. Light--matter interactions are necessary to transfer the information from the matter qubit to the photonic qubit, and this interaction can be enhanced by embedding the spin system in an optical cavity. We focus on photonic crystal microcavities for this purpose, and we study interactions between the optical cavity modes and incorporated spin systems. To improve the performance of this spin--photon interface, it is important to maximize the coupling strength between the spin and photonic systems and to increase the read-out efficiency of information stored in the cavity. In this thesis, we present our work to deterministically couple a nitrogen-vacancy center in diamond to a photonic crystal microcavity in gallium phosphide. This is achieved by nanopositioning a pre-selected diamond nanocrystal in the intensity maximum of the optical cavity mode. We also present an optimized design of a photonic crystal

  11. Multifrequency gap solitons in nonlinear photonic crystals.

    PubMed

    Xie, Ping; Zhang, Zhao-Qing

    2003-11-21

    We predict the existence of multifrequency gap solitons (MFGSs) in both one- and two-dimensional nonlinear photonic crystals. A MFGS is a single intrinsic mode possessing multiple frequencies inside the gap. Its existence is a result of synergic nonlinear coupling among solitons or soliton trains at different frequencies. Its formation can either lower the threshold fields of the respective frequency components or stabilize their excitations. These MFGSs form a new class of stable gap solitons.

  12. Photocurrent response from photonic crystal defect modes.

    PubMed

    Schartner, Stephan; Nobile, Michele; Schrenk, Werner; Andrews, Aaron M; Klang, Pavel; Strasser, Gottfried

    2008-03-31

    The authors use a quantum well intersubband photodetector fabricated into a two dimensional photonic crystal to investigate the optical defect modes of a single missing hole defect. The modes appear as a local enhancement in spectral photocurrent due to an increased in-coupling of surface incident light when a defect mode is present. The frequencies of these localized modes are tracked as they are varied by the defect geometry and compared to simulations. PMID:18542578

  13. Luminescent Magneto-Optical Photonic Crystals

    NASA Astrophysics Data System (ADS)

    Grishin, A. M.; Khartsev, S. I.

    2012-03-01

    We compare luminescent properties of several Er-doped garnet films as building blocks in all-garnet heteroepitaxial magneto-optical photonic crystals: La3Ga5O12, Gd3Ga5O12, Y3Fe5O12, Bi3Fe5O12, and Bi2.97Er0.03Fe4Al0.5Ga0.5O12. Er substituents on the dodecahedral lattice sites do not decrease giant Faraday rotation in Bi3Fe5O12 garnet; meanwhile providing intense room temperature C-band photoluminescence (PL). Fe3+ ion works as a sensitizer for Er resulting in fivefold PL enhancement in iron garnets compared to gallium ones. PL lifetime in gallium garnets is in millisecond range reaching 6 ms in Gd2.9Er0.1Ga5O12. The first luminescent one-dimensional heteroepitaxial all-garnet magneto-optical (MO) photonic crystal was composed from diamagnetic Sm3Ga5O12 and MO-active Bi2.97Er0.03Al0.5Ga0.5O12 garnet layers by rf-magnetron sputtering on Gd3Ga5O12(111) substrate. Substitution of ferric ions by aluminum and gallium improved transparency and induced perpendicular anisotropy in pure Bi3Fe5O12. Photonic crystals owned a record high magneto-optical quality and a latching type (magnetic remnant) Faraday rotation (FR). At the resonance wavelength 775 nm, specific FR θF = - 14.1 deg/μm and MO-quality factor Q = 99.3 deg represent the highest MO performance achieved so far. Long-lived near-IR luminescence in Er substituted gallium and iron garnet layers used both as Bragg mirrors and microcavities promises magneto-optical photonic crystals to become an active lasing medium.

  14. Electromagnetic waves: Negative refraction by photonic crystals

    NASA Astrophysics Data System (ADS)

    Ozbay, Ekmel

    2004-03-01

    Recently left-handed materials (LHM) attracted great attention since these materials exhibit negative effective index, which is due to simultaneously negative permeability and permittivity. Pendry proposed that negative effective index in left-handed materials can be used for constructing a perfect lens, which is not limited by diffraction(J. B. Pendry, Negative refraction makes a perfect lens, Phys. Rev. Lett. vol. 85, 3966 (2000)). Negative refraction is also achievable in a dielectric photonic crystal (PC) that has a periodically modulated positive permittivity and a permeability of unity. Luo et al. has studied negative refraction and subwavelength imaging in photonic crystals(C. Luo, S. G. Johnson, J. D. Joannopoulos, J. B. Pendry, Subwavelength Imaging in Photonic Crystals Phys. Rev. B 68, 045115 (2003)). In this presentation, we report our experimental and theoretical investigation of negative refraction and subwavelength focusing of electromagnetic waves in a 2D PC. Our structure consists of a square array of dielectric rods in air. Transmission measurements are performed for experimentally verifying the predicted negative refraction behavior in our structure. Negative index of refraction determined from the experiment is -1.94 which is very close to the theoretical value of -2.06. Negative refraction is observed for the incidence angles of > 20°(Ertugrul Cubukcu, Koray Aydin, Ekmel Ozbay, S. Foteinopolou, and Costas Soukoulis, Negative Refraction by Photonic Crystals, Nature, vol. 423, 604 (2003)). Since we know the optimum frequency for a broad angle negative refraction, we can use our crystal to test the superlensing effect that was predicted for negative refractive materials. Scanning transmission measurement technique is used to measure the spatial power distribution of the focused electromagnetic waves that radiate from a point source. Full width at half maximum of the focused beam is measured to be 0.21λ, which is in good agreement with the finite

  15. Ultraviolet guiding hollow-core photonic crystal fiber.

    PubMed

    Février, Sébastien; Gérôme, Frédéric; Labruyère, Alexis; Beaudou, Benoît; Humbert, Georges; Auguste, Jean-Louis

    2009-10-01

    We present what we believe to be the first experimental demonstration of low-loss guiding of UV radiation in hollow-core photonic crystal fiber. The "kagomé" latticed fiber was designed to guide 0.355 microm wavelength radiation with approximately 2 dB/m loss. Moreover, an excellent agreement between modeling and experimental results was obtained. From this comparison it was inferred that propagation loss only arises from the lack of confinement, thereby indicating that such fibers may be designed for even shorter wavelengths where material loss prohibits the use of fused silica as a core material. As an example, a fiber was designed to be operated at 0.25 microm with 0.4 dB/m loss.

  16. Highly sensitive and fast response gas sensor based on a light reflection at the glass-photonic crystal interface

    NASA Astrophysics Data System (ADS)

    Kuchyanov, A. S.; Chubakov, P. A.; Plekhanov, A. I.

    2015-09-01

    We develop a versatile gas sensor based on the condition for total internal reflection at the glass-photonic crystal interface and corresponding detection scheme for rapid and precise measurement of vapors. The sensor consists of a vapor sensitive photonic crystal film as a Fabry-Perot etalon coated on a solid substrate (e.g., large face of a glass prism or glass slide). Such scheme and specific physicochemical properties of submicron silica particles provide photonic crystal sensor selectivity due to the capillary condensation of ammonia vapor with a sensitivity of 1 ppm with a response time of 100 ms.

  17. Nanoimprinted polymer photonic crystal dye lasers

    NASA Astrophysics Data System (ADS)

    Christiansen, Mads B.; Smith, Cameron L. C.; Buss, Thomas; Xiao, Sanshui; Mortensen, Niels A.; Kristensen, Anders

    2010-05-01

    Optically pumped polymer photonic crystal band-edge dye lasers are presented. The photonic crystal is a rectangular lattice providing laser feedback as well as an optical resonance for the pump light. The lasers are defined in a thin film of photodefinable Ormocore hybrid polymer, doped with the laser dye Pyrromethene 597. A compact frequency doubled Nd:YAG laser (352 nm, 5 ns pulses) is used to pump the lasers from above the chip. The laser devices are 450 nm thick slab waveguides with a rectangular lattice of 100 nm deep air holes imprinted into the surface. The 2-dimensional rectangular lattice is described by two orthogonal unit vectors of length a and b, defining the ΓP and ΓX directions. The frequency of the laser can be tuned via the lattice constant a (187 nm - 215 nm) while pump light is resonantly coupled into the laser from an angle (θ) depending on the lattice constant b (355 nm). The lasers are fabricated in parallel on a 10 cm diameter wafer by combined nanoimprint and photolithography (CNP). CNP relies on a UV transparent quartz nanoimprint stamp with an integrated metal shadow mask. In the CNP process the photonic crystal is formed by mechanical deformation (imprinting) while the larger features are defined by UV exposure through the combined mask/mold.

  18. Amorphous photonic crystals with only short-range order.

    PubMed

    Shi, Lei; Zhang, Yafeng; Dong, Biqin; Zhan, Tianrong; Liu, Xiaohan; Zi, Jian

    2013-10-01

    Distinct from conventional photonic crystals with both short- and long-range order, amorphous photonic crystals that possess only short-range order show interesting optical responses owing to their unique structural features. Amorphous photonic crystals exhibit unique light scattering and transport, which lead to a variety of interesting phenomena such as isotropic photonic bandgaps or pseudogaps, noniridescent structural colors, and light localization. Recent experimental and theoretical advances in the study of amorphous photonic crystals are summarized, focusing on their unique optical properties, artificial fabrication, bionspiration, and potential applications.

  19. Feasibility of tunable MEMS photonic crystal devices.

    PubMed

    Rajic, S; Corbeil, J L; Datskos, P G

    2003-01-01

    Periodic photonic crystal structures channel electromagnetic waves much as semiconductors/quantum wells channel electrons. Photonic bandgap crystals (PBC) are fabricated by arranging sub-wavelength alternating materials with high and low dielectric constants to produce a desired effective bandgap. Photons with energy within this bandgap cannot propagate through the structure. This property has made these structures useful for microwave applications such as frequency-selective surfaces, narrowband filters, and antenna substrates when the dimensions are on the order of millimeters. They are also potentially very useful, albeit much more difficult to fabricate, in the visible/near-infrared region for various applications when the smallest dimensions are at the edge of current micro-lithography fabrication tools. We micro-fabricated suspended free standing micro-structure bridge waveguides to serve as substrates for PBC features. These micro-bridges were fabricated onto commercial silicon-on-insulator wafers. Nanoscale periodic features were fabricated onto these micro-structure bridges to form a tunable system. When this combined structure is perturbed, such as mechanical deflection of the suspended composite structure at resonance, there can be a realtime shift in the material effective bandgap due to slight geometric alterations due to the induced mechanical stress. Extremely high resonance frequencies/device speeds are possible with these very small dimension MEMS.

  20. Biological fabrication of nanostructured silicon-germanium photonic crystals possessing unique photoluminescent and electroluminescent properties

    NASA Astrophysics Data System (ADS)

    Rorrer, Gregory L.; Jeffryes, Clayton; Chang, Chih-hung; Lee, Doo-Hyoung; Gutu, Timothy; Jiao, Jun; Solanki, Raj

    2007-09-01

    Diatoms are single-celled algae which possess silica shells called "frustules" that contain periodic submicron scale features. A diatom cell culture process was used to fabricate a two-dimensional photonic crystal slab of Ge-doped biosilica that possessed 120 nm holes, 330 nm lattice constant, and dielectric constant of 8.5. This material was integrated into an electroluminescent (EL) device by spin coating of the frustules onto indium tin oxide, followed by atomic layer deposition of 400 nm hafnium silicate. No photonic band gap was predicted. However, the EL spectrum possessed resonant UV line emissions that were consistent with photonic band calculations. An EL band gap between 500-640 nm was also observed between blue and red EL line emissions. These EL characteristics have not been observed previously, and are unique to the diatom photonic crystal. This study represents a first step towards the realization of optoelectronic devices which utilize nanoscale components fabricated through cell culture.

  1. Raman cooling in silicon photonic crystals

    NASA Astrophysics Data System (ADS)

    Chen, Yin-Chung; Bahl, Gaurav

    2016-03-01

    Laser cooling of solids can be achieved through various photon up-conversion processes including anti-Stokes photoluminescence and anti-Stokes light scattering. While it has been shown that cooling using photoluminescence-based methods can achieve efficiency comparable to that of thermoelectric cooling, the reliance on specific transitions of the rare-earth dopants limits material choice. Light scattering, on the other hand, occurs in all materials, and has the potential to enable cooling in most materials. We show that by engineering the photonic density of states of a material, one can suppress the Stokes process, and enhance the anti-Stokes radiation. We employ the well-known diamond-structured photonic crystal patterned in crystalline silicon to demonstrate theoretically that when operating within a high transparency regime, the net energy removal rate from phonon annihilation can overcome the optical absorption. The engineered photonic density of states can thus enable simultaneous cooling of all Raman-active phonon modes and the net cooling of the solid.

  2. Photonic Crystal Emitters for Thermophotovoltaic Energy Conversion

    NASA Astrophysics Data System (ADS)

    Stelmakh, Veronika; Chan, Walker R.; Ghebrebrhan, Michael; Soljacic, Marin; Joannopoulos, John D.; Celanovic, Ivan

    2015-12-01

    This paper reports the design, fabrication, and characterization of 2D photonic crystal (PhC) thermal emitters for a millimeter-scale hydrocarbon TPV microgenerator as a possible replacement for batteries in portable microelectronics, robotics, etc. In our TPV system, combustion heats a PhC emitter to incandescence and the resulting radiation is converted by a low-bandgap TPV cell. The PhC tailors the photonic density of states to produce spectrally confined thermal emission that matches the bandgap of the TPV cell, enabling high heat-to-electricity conversion efficiency. The work builds on a previously developed fabrication process to produce a square array of cylindrical cavities in a metal substrate. We will present ongoing incremental improvements in the optical and thermo-mechanical properties, the fabrication process, and the system integration, as recently combined with fabrication using novel materials, such as sputtered coatings, to enable a monolithic system.

  3. Chalcogenide glass hollow core photonic crystal fibers

    NASA Astrophysics Data System (ADS)

    Désévédavy, Frédéric; Renversez, Gilles; Troles, Johann; Houizot, Patrick; Brilland, Laurent; Vasilief, Ion; Coulombier, Quentin; Traynor, Nicholas; Smektala, Frédéric; Adam, Jean-Luc

    2010-09-01

    We report the first hollow core photonic crystal fibers (HC PCF) in chalcogenide glass. To design the required HC PCF profiles for such high index glass, we use both band diagram analysis to define the required photonic bandgap and numerical simulations of finite size HC PCFs to compute the guiding losses. The material losses have also been taken into account to compute the overall losses of the HC PCF profiles. These fibers were fabricated by the stack and draw technique from TeAsSe (TAS) glass. The fibers we drew in this work are composed of six rings of holes and regular microstructures. Two profiles are presented, one is known as a kagome lattice and the other one corresponds to a triangular lattice. Geometrical parameters are compared to the expected parameters obtained by computation. Applications of such fibers include power delivery or fiber sensors among others.

  4. Slab photonic crystals with dimer colloid bases

    SciTech Connect

    Riley, Erin K.; Liddell Watson, Chekesha M.

    2014-06-14

    The photonic band gap properties for centered rectangular monolayers of asymmetric dimers are reported. Colloids in suspension have been organized into the phase under confinement. The theoretical model is inspired by the range of asymmetric dimers synthesized via seeded emulsion polymerization and explores, in particular, the band structures as a function of degree of lobe symmetry and degree of lobe fusion. These parameters are varied incrementally from spheres to lobe-tangent dimers over morphologies yielding physically realizable particles. The work addresses the relative scarcity of theoretical studies on photonic crystal slabs with vertical variation that is consistent with colloidal self-assembly. Odd, even and polarization independent gaps in the guided modes are determined for direct slab structures. A wide range of lobe symmetry and degree of lobe fusion combinations having Brillouin zones with moderate to high isotropy support gaps between odd mode band indices 3-4 and even mode band indices 1-2 and 2-3.

  5. Photonic crystal devices formed by a charged-particle beam

    DOEpatents

    Lin, Shawn-Yu; Koops, Hans W. P.

    2000-01-01

    A photonic crystal device and method. The photonic crystal device comprises a substrate with at least one photonic crystal formed thereon by a charged-particle beam deposition method. Each photonic crystal comprises a plurality of spaced elements having a composition different from the substrate, and may further include one or more impurity elements substituted for spaced elements. Embodiments of the present invention may be provided as electromagnetic wave filters, polarizers, resonators, sources, mirrors, beam directors and antennas for use at wavelengths in the range from about 0.2 to 200 microns or longer. Additionally, photonic crystal devices may be provided with one or more electromagnetic waveguides adjacent to a photonic crystal for forming integrated electromagnetic circuits for use at optical, infrared, or millimeter-wave frequencies.

  6. Broadband photon-photon interactions mediated by cold atoms in a photonic crystal fiber

    PubMed Central

    Litinskaya, Marina; Tignone, Edoardo; Pupillo, Guido

    2016-01-01

    We demonstrate theoretically that photon-photon attraction can be engineered in the continuum of scattering states for pairs of photons propagating in a hollow-core photonic crystal fiber filled with cold atoms. The atoms are regularly spaced in an optical lattice configuration and the photons are resonantly tuned to an internal atomic transition. We show that the hard-core repulsion resulting from saturation of the atomic transitions induces bunching in the photonic component of the collective atom-photon modes (polaritons). Bunching is obtained in a frequency range as large as tens of GHz, and can be controlled by the inter-atomic separation. We provide a fully analytical explanation for this phenomenon by proving that correlations result from a mismatch of the quantization volumes for atomic excitations and photons in the continuum. Even stronger correlations can be observed for in-gap two-polariton bound states. Our theoretical results use parameters relevant for current experiments and suggest a simple and feasible way to induce interactions between photons. PMID:27170160

  7. High birefringence liquid crystals for photonic applications

    NASA Astrophysics Data System (ADS)

    Gauza, S.; Wen, C. H.; Wu, S. T.; Dabrowski, R.; Hsu, C. S.; Catanescu, C. O.; Chien, L. C.

    2005-09-01

    High birefringence liquid crystals (LCs) play an important role for laser beam steering, tunable-focus lens, reflective display, cholesteric LC laser, infrared dynamic scene projector, and telecom variable optical attenuator applications. We have developed some high birefringence compounds and eutectic mixtures with birefringence in the 0.4-0.7 range. For some photonic devices where response time is critical, we have also developed high birefringence dual-frequency LC mixtures. The cross-over frequency is around 5-10 kHz. Using such a dual-frequency LC mixture, sub-millisecond response time is achieved.

  8. Super-collimation by axisymmetric photonic crystals

    SciTech Connect

    Purlys, V.; Gailevičius, D.; Peckus, M.; Gadonas, R.; Maigyte, L.; Staliunas, K.

    2014-06-02

    We propose and experimentally show the mechanism of beam super-collimation by axisymmetric photonic crystals, specifically by periodic (in propagation direction) structure of layers of concentric rings. The physical mechanism behind the effect is an inverse scattering cascade of diffracted wave components back into on- and near-axis angular field components, resulting in substantial enhancement of intensity of these components. We explore the super-collimation by numerical calculations and prove it experimentally. We demonstrate experimentally the axial field enhancement up to 7 times in terms of field intensity.

  9. Photonic crystal self-collimation sensor.

    PubMed

    Wang, Yufei; Wang, Hailing; Xue, Qikun; Zheng, Wanhua

    2012-05-21

    A novel refractive index sensor based on the two dimensional photonic crystal folded Michelson interferometer employing the self-collimation effect is proposed and its performances are theoretically investigated. Two sensing areas are included in the sensor. Simulation results indicate the branch area is suitable for the small index variety range and fine detection, whereas the reflector area prone to the large index change range and coarse detection. Because of no defect waveguides and no crosstalk of signal, the sensor is desirable to perform monolithic integrated, low-cost, label-free real-time parallel sensing. In addition, a flexible design of self-collimation sensors array is demonstrated. PMID:22714197

  10. Reversed Doppler effect in photonic crystals.

    PubMed

    Reed, Evan J; Soljacić, Marin; Joannopoulos, John D

    2003-09-26

    Nonrelativistic reversed Doppler shifts have never been observed in nature and have only been speculated to occur in pathological systems with simultaneously negative effective permittivity and permeability. This Letter presents a different, new physical phenomenon that leads to a nonrelativistic reversed Doppler shift in light. It arises when light is reflected from a moving shock wave propagating through a photonic crystal. In addition to reflection of a single frequency, multiple discrete reflected frequencies or a 10 GHz periodic modulation can also be observed when a single carrier frequency of wavelength 1 microm is incident.

  11. Anomalous bending effect in photonic crystal fibers

    PubMed Central

    Tu, Haohua; Jiang, Zhi; Marks, Daniel. L.; Boppart, Stephen A.

    2010-01-01

    An unexpected transmission loss up to 50% occurs to intense femtosecond pulses propagating along an endlessly single-mode photonic crystal fiber over a length of 1 m. A specific leaky-fiber mode gains amplification along the fiber at the expense of the fundamental fiber mode through stimulated four-wave mixing and Raman scattering, leading to this transmission loss. Bending near the fiber entrance dissipates the propagating seed of this leaky mode, preventing the leaky mode amplification and therefore enhancing the transmission of these pulses. PMID:18542666

  12. Reciprocity theorem and perturbation theory for photonic crystal waveguides.

    PubMed

    Michaelis, D; Peschel, U; Wächter, C; Bräuer, A

    2003-12-01

    Starting from Maxwell's equations we derive a reciprocity theorem for photonic crystal waveguides. A set of strongly coupled discrete equations results, which can be applied to the simulation of perturbed photonic crystal waveguides. As an example we analytically study the influence of the dispersion of a two level system on the band structure of a photonic crystal waveguide. In particular, the formation of polariton gaps is discussed.

  13. Young's double-slit experiment in photonic crystals

    SciTech Connect

    Zhang, Lei; Koschny, Thomas; Soukoulis, Costas M.

    2012-10-01

    We present an experimental and numerical study of the transmission of a photonic crystal perforated by two sub-wavelength slits, separated by two wavelengths.The experimental near-field image of the double-slit design of the photonic crystal shows an interference pattern, which is analogous to Young’s experiment. This interference arises as a consequence of the excitation of surface states of the photonic crystals and agrees very well with the simulations.

  14. Porous photonic crystal external cavity laser biosensor

    NASA Astrophysics Data System (ADS)

    Huang, Qinglan; Peh, Jessie; Hergenrother, Paul J.; Cunningham, Brian T.

    2016-08-01

    We report the design, fabrication, and testing of a photonic crystal (PC) biosensor structure that incorporates a porous high refractive index TiO2 dielectric film that enables immobilization of capture proteins within an enhanced surface-area volume that spatially overlaps with the regions of resonant electromagnetic fields where biomolecular binding can produce the greatest shifts in photonic crystal resonant wavelength. Despite the nanoscale porosity of the sensor structure, the PC slab exhibits narrowband and high efficiency resonant reflection, enabling the structure to serve as a wavelength-tunable element of an external cavity laser. In the context of sensing small molecule interactions with much larger immobilized proteins, we demonstrate that the porous structure provides 3.7× larger biosensor signals than an equivalent nonporous structure, while the external cavity laser (ECL) detection method provides capability for sensing picometer-scale shifts in the PC resonant wavelength caused by small molecule binding. The porous ECL achieves a record high figure of merit for label-free optical biosensors.

  15. Fabrication and evaluation of photonic metamaterial crystal

    NASA Astrophysics Data System (ADS)

    Tanabete, S.; Nakagawa, Y.; Okamoto, T.; Haraguchi, M.; Isu, T.; Shinomiya, G.

    2013-09-01

    Many researching efforts have been reported to seek various fundamental LC resonance structures, recently. But still the Split Ring Resonator (SRR) is the most famous and major fundamental LC-resonance structure used in the metamaterial. We employed SRR structure as the fundamental LC-resonance mechanism to fabricate photonic crystal with periodic arrangement of two different metamaterial areas composed from SRR arrays on the dielectric substrate. We developed Photonic Metamaterial Crystal (PMC) to realize the more advanced and versatile functions of the metamaterial by 1 dimensional or 2 dimensional periodic arranging of two metamaterial sections which have different dispersion properties due to the different size of SRR structures each other. In this paper, we report the fabrication process, estimation of PMC properties and some possible future application prospects, for instance the PMC waveguide structures and nonlinear properties of PMC observed as selective LC-resonant properties in Raman mapping analysis of PMC. These are quite interesting characters of PMC and the attractive applications as the PMC devices.

  16. Photonic Crystal Laser-Driven Accelerator Structures

    SciTech Connect

    Cowan, Benjamin M.

    2007-08-22

    Laser-driven acceleration holds great promise for significantly improving accelerating gradient. However, scaling the conventional process of structure-based acceleration in vacuum down to optical wavelengths requires a substantially different kind of structure. We require an optical waveguide that (1) is constructed out of dielectric materials, (2) has transverse size on the order of a wavelength, and (3) supports a mode with speed-of-light phase velocity in vacuum. Photonic crystals---structures whose electromagnetic properties are spatially periodic---can meet these requirements. We discuss simulated photonic crystal accelerator structures and describe their properties. We begin with a class of two-dimensional structures which serves to illustrate the design considerations and trade-offs involved. We then present a three-dimensional structure, and describe its performance in terms of accelerating gradient and efficiency. We discuss particle beam dynamics in this structure, demonstrating a method for keeping a beam confined to the waveguide. We also discuss material and fabrication considerations. Since accelerating gradient is limited by optical damage to the structure, the damage threshold of the dielectric is a critical parameter. We experimentally measure the damage threshold of silicon for picosecond pulses in the infrared, and determine that our structure is capable of sustaining an accelerating gradient of 300 MV/m at 1550 nm. Finally, we discuss possibilities for manufacturing these structures using common microfabrication techniques.

  17. Negative Refraction experiments in Photonic Crystal prisms

    NASA Astrophysics Data System (ADS)

    Vodo, Plarenta; Parimi, Patanjali. V.; Lu, Wentao. T.; di Gennaro, Emiliano; Sridhar, Srinivas

    2004-03-01

    We have experimentally demonstrated negative refraction in metallic photonic crystal (PC) prisms [1]. The refracted fields in the parallel plate waveguide (PPW) are measured by an automated dipole antenna, which scans the desired area, while the free space (FS) measurements, performed in a anechoic chamber, are measured by a rectangular X-band horn that swings in an arc in far field area. Both TE and TM excitation modes are used in FS experiments. Numerical calculations of the band structure and equi-frequency surface simulations are used to determine frequency regions of negative refraction of the triangular lattice PC. Angle of refraction determined by theoretical simulations and experimental results, are in exceptional good agreement, yielding the negative refraction index. FS and PPW refraction experimental results agree remarkably with simulations. 1. "Negative Refraction and Left-handed electromagnetism in Microwave Photonic Crystals", P.V Parimi, W.T Lu, P.Vodo J. Sokoloff and S.Sridhar, cond-mat/0306109 (2003)

  18. Gallium nitride based logpile photonic crystals.

    PubMed

    Subramania, Ganapathi; Li, Qiming; Lee, Yun-Ju; Figiel, Jeffrey J; Wang, George T; Fischer, Arthur J

    2011-11-01

    We demonstrate a nine-layer logpile three-dimensional photonic crystal (3DPC) composed of single crystalline gallium nitride (GaN) nanorods, ∼100 nm in size with lattice constants of 260, 280, and 300 nm with photonic band gap in the visible region. This unique GaN structure is created through a combined approach of a layer-by-layer template fabrication technique and selective metal organic chemical vapor deposition (MOCVD). These GaN 3DPC exhibit a stacking direction band gap characterized by strong optical reflectance between 380 and 500 nm. By introducing a "line-defect" cavity in the fifth (middle) layer of the 3DPC, a localized transmission mode with a quality factor of 25-30 is also observed within the photonic band gap. The realization of a group III nitride 3DPC with uniform features and a band gap at wavelengths in the visible region is an important step toward realizing complete control of the electromagnetic environment for group III nitride based optoelectronic devices.

  19. Extended-Range Ultrarefractive 1D Photonic Crystal Prisms

    NASA Technical Reports Server (NTRS)

    Ting, David Z.

    2007-01-01

    A proposal has been made to exploit the special wavelength-dispersive characteristics of devices of the type described in One-Dimensional Photonic Crystal Superprisms (NPO-30232) NASA Tech Briefs, Vol. 29, No. 4 (April 2005), page 10a. A photonic crystal is an optical component that has a periodic structure comprising two dielectric materials with high dielectric contrast (e.g., a semiconductor and air), with geometrical feature sizes comparable to or smaller than light wavelengths of interest. Experimental superprisms have been realized as photonic crystals having three-dimensional (3D) structures comprising regions of amorphous Si alternating with regions of SiO2, fabricated in a complex process that included sputtering. A photonic crystal of the type to be exploited according to the present proposal is said to be one-dimensional (1D) because its contrasting dielectric materials would be stacked in parallel planar layers; in other words, there would be spatial periodicity in one dimension only. The processes of designing and fabricating 1D photonic crystal superprisms would be simpler and, hence, would cost less than do those for 3D photonic crystal superprisms. As in 3D structures, 1D photonic crystals may be used in applications such as wavelength-division multiplexing. In the extended-range configuration, it is also suitable for spectrometry applications. As an engineered structure or artificially engineered material, a photonic crystal can exhibit optical properties not commonly found in natural substances. Prior research had revealed several classes of photonic crystal structures for which the propagation of electromagnetic radiation is forbidden in certain frequency ranges, denoted photonic bandgaps. It had also been found that in narrow frequency bands just outside the photonic bandgaps, the angular wavelength dispersion of electromagnetic waves propagating in photonic crystal superprisms is much stronger than is the angular wavelength dispersion obtained

  20. Experimental and theoretical investigations of three-dimensional photonic crystals with unique architectures

    NASA Astrophysics Data System (ADS)

    Galusha, Jeremy Wayne

    Three dimensional photonic crystals based on self-assembled opal frameworks and naturally occurring diamond-based architectures were studied. The optical behavior of the photonic crystals was investigated using reflectance spectroscopy. Structural characteristics were determined using a combination of scanning electron and optical microscopy. Titania photonic crystal structures were fabricated using a variety of infiltration/replication strategies. A simple sol-gel chemistry-based opal infiltration method for the fabrication of high quality planar titania photonic crystals was developed. Polystyrene synthetic opals were infiltrated with a hydrophobic and air/moisture-stable liquid titania precursor. The high stability and hydrophobicity of the titania precursor enabled a new "lift-off/turn-over" backfilling technique that after calcination gives planar titania inverse opals with a flat and completely open surface. Two different infiltration strategies and their influence on the structural and photonic properties were investigated. The obtained inverse opals display excellent photonic properties as evidenced by the presence of first-, second-, and third-order Bragg reflection peaks in accordance with theoretical photonic band structure calculations. The photonic crystal structure inside iridescent scales of the weevil Lamprocyphus augustus was investigated. By combining a high-resolution structure analysis technique based on sequential focused ion beam milling and scanning electron microscopy imaging with theoretical modeling and photonic band-structure calculations, the structure was determined to be a natural three-dimensional photonic structure with a diamond-based crystal lattice operating at visible wavelengths. A bio-templating route was developed to fabricate high-dielectric diamond-based photonic crystals with lattice periodicities at visible wavelengths. A sol-gel double-imprint strategy via a mesostructured organo-silica intermediary is developed to

  1. Memory effect in composites of liquid crystal and silica aerosil

    SciTech Connect

    Relaix, Sabrina; Leheny, Robert L.; Reven, Linda; Sutton, Mark

    2012-02-07

    Aerosil silica nanoparticles dispersed in a liquid crystal (LC) possess the interesting property of keeping memory of an electric- or magnetic-field-induced orientation. Two types of memory have been identified: thermally erasable memory arising from the pinning of defect lines versus a 'permanent' memory where the orientation persists even after thermal cycling the samples up to the isotropic phase. To address the source of the latter type of memory, solid-state nuclear magnetic resonance spectroscopy and conventional x-ray diffraction (XRD) were first combined to characterize the LC orientational order as a function of multiple in-field temperature cycles. Microbeam XRD was then performed on aligned gels of different concentrations to gain knowledge of the structural properties at the origin of the memory effect. No detectable anisotropy of the gel or significant breaking of silica strands with heating ruled out the formation of an anisotropic silica network as the source of the permanent memory as previously proposed. Instead, support for a role of the surface memory effect, well known for planar substrates, in stabilizing the permanent memory was deduced from 'training' of the composites, that is, optimizing the orientational order through the thermal in-field cycling. The ability to train the composites is inversely proportional to the strength of the random-field disorder. The portion of thermally erasable memory also decreases as the silica density increases. We propose that the permanent memory originates from the surface memory effect operating at points of intersection in the silica network. These areas, where the LC is strongly confined with conflicted surface interactions, are trained to achieve an optimized orientation and subsequently act as sites from which the LC orientational order regrows after zero-field thermal cycling up to the isotropic phase.

  2. A 1-D dusty plasma photonic crystal

    SciTech Connect

    Mitu, M. L.; Ticoş, C. M.; Toader, D.; Banu, N.; Scurtu, A.

    2013-09-21

    It is demonstrated numerically that a 1-D plasma crystal made of micron size cylindrical dust particles can, in principle, work as a photonic crystal for terahertz waves. The dust rods are parallel to each other and arranged in a linear string forming a periodic structure of dielectric-plasma regions. The dispersion equation is found by solving the waves equation with the boundary conditions at the dust-plasma interface and taking into account the dielectric permittivity of the dust material and plasma. The wavelength of the electromagnetic waves is in the range of a few hundred microns, close to the interparticle separation distance. The band gaps of the 1-D plasma crystal are numerically found for different types of dust materials, separation distances between the dust rods and rod diameters. The distance between levitated dust rods forming a string in rf plasma is shown experimentally to vary over a relatively wide range, from 650 μm to about 1350 μm, depending on the rf power fed into the discharge.

  3. All-optical NOR and NAND gates based on photonic crystal ring resonator

    NASA Astrophysics Data System (ADS)

    Bao, Junjie; Xiao, Jun; Fan, Lin; Li, Xiaoxu; Hai, Yunfei; Zhang, Tong; Yang, Chunbo

    2014-10-01

    We report a new configuration of all-optical logic gates based on two-dimensional (2D) square lattice photonic crystals (PCs) composed of silicon (Si) rods in Silica (SiO2). The proposed device is composed of cross-shaped waveguide and two photonic crystal ring resonators (PCRRs) without nonlinear materials and optical amplifiers. The gate has been simulated and analyzed by finite difference time domain (FDTD) and plane wave expansion (PWE) methods. The simulation results show that the proposed all-optical logic gates could really function as NOR and NAND logic gates. This new device can potentially be used in large-scale optical integration and on-chip photonic logic integrated circuits.

  4. Spherulitic crystallization of holmium tartrates in silica gels

    NASA Astrophysics Data System (ADS)

    Want, Basharat

    2011-09-01

    Spherulites of holmium tartrate trihydrate and holmium nitro-tartrate monohydrate have been grown in silica gel medium by making holmium nitrate to react with tartaric acid at high supersaturations. The mechanism of spherulitic growth of holmium tartrates is discussed. The spherulitic crystallization is shown to be due to heterogeneous nucleation. In the early stages of growth an amorphous spherical mass gets nucleated inside the gel. Crystal fibers diverge radially from the surface of the spherical mass giving rise to a spherical polycrystalline holmium tartrate. Thermal stability of the two types of spherulites grown in the silica gel shows that the holmium tartrate trihydrate is more stable than holmium nitro-tartrate monohydrate. The surface morphology and internal structure of the spherulites of holmium tartrates have been studied by using scanning electron microscopy. The results on growth kinetics are given by studying the variation of radius of spherulites as a function of time. A non-linear time-size relations under several conditions of growth have been observed, which suggests a non-uniform solute concentration at the crystal surface.

  5. [Recent advancement of photonic-crystal-based analytical chemistry].

    PubMed

    Chen, Yun; Guo, Zhenpeng; Wang, Jinyi; Chen, Yi

    2014-04-01

    Photonic crystals are a type of novel materials with ordered structure, nanopores/channels and optical band gap. They have hence important applications in physics, chemistry, biological science and engineering fields. This review summarizes the recent advancement of photonic crystals in analytical chemistry applications, with focus on sensing and separating fields happening in the nearest 5 years.

  6. Interface electromagnetic waves between Kronig-Penney photonic crystals

    NASA Astrophysics Data System (ADS)

    Mehrany, Khashayar; Momeni, Babak; Khorasani, Sina; Rashidian, Bizhan

    2003-02-01

    The electromagnetic interface states formed in a heterostructure composed of two semi-infinite Kronig-Penny photonic crystals have been studied. Modified transfer matrices have been used for study of Kronig-Penny photonic crystals (heterostructures with conducting interfaces) to show strong similarity between solid-state physics and electromagnetics. Our calculations are limited to TE polarization.

  7. Heteroplasmon hybridization in stacked complementary plasmo-photonic crystals.

    PubMed

    Iwanaga, Masanobu; Choi, Bongseok

    2015-03-11

    We constructed plasmo-photonic crystals in which efficient light-trapping, plasmonic resonances couple with photonic guided resonances of large density of states and high-quality factor. We have numerically and experimentally shown that heteroplasmon hybrid modes emerge in stacked complementary (SC) plasmo-photonic crystals. The resonant electromagnetic-field distributions evidence that the two hybrid modes originate from two different heteroplasmons, exhibiting a large energy splitting of 300 meV. We further revealed a series of plasmo-photonic modes in the SC crystals.

  8. Waveguide circuits in three-dimensional photonic crystals

    SciTech Connect

    Biswas, Rana; Christensen, C.; Muehlmeier, J.; Tuttle, G.; Ho, K.-M.

    2008-04-07

    Waveguide circuits in three-dimensional photonic crystals with complete photonic band gaps are simulated with finite difference time domain (FDTD) simulations, and compared with measurements on microwave scale photonic crystals. The transmission through waveguide bends critically depends on the photonic crystal architecture in the bend region. We have found experimentally and theoretically, a new waveguide bend configuration consisting of overlapping rods in the bend region, that performs better than the simple waveguide bend of terminated rods, especially in the higher frequency portion of the band. Efficient beam splitters with this junction geometry are also simulated.

  9. A mesoporous silica biomaterial for dental biomimetic crystallization.

    PubMed

    Chiang, Yu-Chih; Lin, Hong-Ping; Chang, Hao-Hueng; Cheng, Ya-Wen; Tang, Hsin-Yen; Yen, Wei-Ching; Lin, Po-Yen; Chang, Kei-Wen; Lin, Chun-Pin

    2014-12-23

    The loss of overlying enamel or cementum exposes dentinal tubules and increases the risk of several dental diseases, such as dentin hypersensitivity (causing sharp pain and anxiety), caries, and pulp inflammation. This paper presents a fast-reacting, more reliable and biocompatible biomaterial that effectively occludes exposed dentinal tubules by forming a biomimetic crystalline dentin barrier. To generate this biomaterial, a gelatin-templated mesoporous silica biomaterial (CaCO3@mesoporous silica, CCMS) containing nanosized calcium carbonate particles is mixed with 30% H3PO4 at a 1/1 molar ratio of Ca/P (denoted as CCMS-HP), which enables Ca2+ and PO4(3-)/HPO4(2-) ions to permeate the dentinal tubules and form dicalcium phosphate dihydrate (DCPD), tricalcium phosphate (TCP) or hydroxyapatite (HAp) crystals at a depth of approximately 40 μm (sub-μ-CT and nano-SEM/EDS examinations). In vitro biocompatibility tests (WST-1 and lactate dehydrogenase) and ALP assays show high cell viability and mineralization ability in a transwell dentin disc model treated with CCMS-HP (p<0.05). The in vivo efficacy and biocompatibility analyses of the biomaterial in an animal model reveal significant crystal growth (DCPD, TCP or HAp-like) and no pulp irritation after 70 days (p<0.05). The developed CCMS-HP holds great promise for treating exposed dentin by growing biomimetic crystals within dentinal tubules. These findings demonstrate that the mesoporous silica biomaterials presented here have great potential for serving as both a catalyst and carrier in the repair or regeneration of dental hard tissue.

  10. Strongly-Refractive One-Dimensional Photonic Crystal Prisms

    NASA Technical Reports Server (NTRS)

    Ting, David Z. (Inventor)

    2004-01-01

    One-dimensional (1D) photonic crystal prisms can separate a beam of polychromatic electromagnetic waves into constituent wavelength components and can utilize unconventional refraction properties for wavelength dispersion over significant portions of an entire photonic band rather than just near the band edges outside the photonic band gaps. Using a ID photonic crystal simplifies the design and fabrication process and allows the use of larger feature sizes. The prism geometry broadens the useful wavelength range, enables better optical transmission, and exhibits angular dependence on wavelength with reduced non-linearity. The properties of the 1 D photonic crystal prism can be tuned by varying design parameters such as incidence angle, exit surface angle, and layer widths. The ID photonic crystal prism can be fabricated in a planar process, and can be used as optical integrated circuit elements.

  11. Two-photon-induced singlet fission in rubrene single crystal.

    PubMed

    Ma, Lin; Galstyan, Gegham; Zhang, Keke; Kloc, Christian; Sun, Handong; Soci, Cesare; Michel-Beyerle, Maria E; Gurzadyan, Gagik G

    2013-05-14

    The two-photon-induced singlet fission was observed in rubrene single crystal and studied by use of femtosecond pump-probe spectroscopy. The location of two-photon excited states was obtained from the nondegenerate two-photon absorption (TPA) spectrum. Time evolution of the two-photon-induced transient absorption spectra reveals the direct singlet fission from the two-photon excited states. The TPA absorption coefficient of rubrene single crystal is 52 cm∕GW at 740 nm, as obtained from Z-scan measurements. Quantum chemical calculations based on time-dependent density functional theory support our experimental data. PMID:23676057

  12. All-polymer photonic crystal slab sensor.

    PubMed

    Hermannsson, Pétur G; Sørensen, Kristian T; Vannahme, Christoph; Smith, Cameron L C; Klein, Jan J; Russew, Maria-Melanie; Grützner, Gabi; Kristensen, Anders

    2015-06-29

    An all-polymer photonic crystal slab sensor is presented, and shown to exhibit narrow resonant reflection with a FWHM of less than 1 nm and a sensitivity of 31 nm/RIU when sensing media with refractive indices around that of water. This results in a detection limit of 4.5 × 10(-6) RIU when measured in conjunction with a spectrometer of 12 pm/pixel resolution. The device is a two-layer structure, composed of a low refractive index polymer with a periodically modulated surface height, covered with a smooth upper-surface high refractive index inorganic-organic hybrid polymer modified with ZrO2based nanoparticles. Furthermore, it is fabricated using inexpensive vacuum-less techniques involving only UV nanoreplication and polymer spin-casting, and is thus well suited for single-use biological and refractive index sensing applications. PMID:26191664

  13. Terahertz wave filter based on photonic crystal

    NASA Astrophysics Data System (ADS)

    Liu, Yu-hang; Li, Jiu-sheng

    2011-11-01

    In the past decade, spectroscopy and imaging in the terahertz region (0.1-10 THz) of the electromagnetic spectrum has been applied in both basic research and potential industrial applications, such as medical diagnosis, security screening, radio astronomy, atmospheric studies, short-range indoor communication, chemical, biological sensing, medical and biological imaging, and detection of explosives. In this paper, we design a narrow bandpass terahertz wave filter using three kinds of two-dimensional photonic crystals. By using finite-difference time-domain (FDTD) method, we examined the transmittance spectra for the proposed terahertz wave filter. The simulated results show that the proposed filter exhibit excellent transmission performance such as high transmission at the central frequency, adjustable bandpass, and good rejection of the sideband frequencies.

  14. Terahertz wave filter based on photonic crystal

    NASA Astrophysics Data System (ADS)

    Liu, Yu-hang; Li, Jiu-sheng

    2012-03-01

    In the past decade, spectroscopy and imaging in the terahertz region (0.1-10 THz) of the electromagnetic spectrum has been applied in both basic research and potential industrial applications, such as medical diagnosis, security screening, radio astronomy, atmospheric studies, short-range indoor communication, chemical, biological sensing, medical and biological imaging, and detection of explosives. In this paper, we design a narrow bandpass terahertz wave filter using three kinds of two-dimensional photonic crystals. By using finite-difference time-domain (FDTD) method, we examined the transmittance spectra for the proposed terahertz wave filter. The simulated results show that the proposed filter exhibit excellent transmission performance such as high transmission at the central frequency, adjustable bandpass, and good rejection of the sideband frequencies.

  15. Enhanced photoacoustic detection using photonic crystal substrate

    NASA Astrophysics Data System (ADS)

    Zhao, Yunfei; Liu, Kaiyang; McClelland, John; Lu, Meng

    2014-04-01

    This paper demonstrates the enhanced photoacoustic sensing of surface-bound light absorbing molecules and metal nanoparticles using a one-dimensional photonic crystal (PC) substrate. The PC structure functions as an optical resonator at the wavelength where the analyte absorption is strong. The optical resonance of the PC sensor provides an intensified evanescent field with respect to the excitation light source and results in enhanced optical absorption by surface-immobilized samples. For the analysis of a light absorbing dye deposited on the PC surface, the intensity of photoacoustic signal was enhanced by more than 10-fold in comparison to an un-patterned acrylic substrate. The technique was also applied to detect gold nanorods and exhibited more than 40 times stronger photoacoustic signals. The demonstrated approach represents a potential path towards single molecule absorption spectroscopy with greater performance and inexpensive instrumentation.

  16. Enhanced photoacoustic detection using photonic crystal substrate

    SciTech Connect

    Zhao, Yunfei; Liu, Kaiyang; McClelland, John; Lu, Meng

    2014-04-21

    This paper demonstrates the enhanced photoacoustic sensing of surface-bound light absorbing molecules and metal nanoparticles using a one-dimensional photonic crystal (PC) substrate. The PC structure functions as an optical resonator at the wavelength where the analyte absorption is strong. The optical resonance of the PC sensor provides an intensified evanescent field with respect to the excitation light source and results in enhanced optical absorption by surface-immobilized samples. For the analysis of a light absorbing dye deposited on the PC surface, the intensity of photoacoustic signal was enhanced by more than 10-fold in comparison to an un-patterned acrylic substrate. The technique was also applied to detect gold nanorods and exhibited more than 40 times stronger photoacoustic signals. The demonstrated approach represents a potential path towards single molecule absorption spectroscopy with greater performance and inexpensive instrumentation.

  17. 2D photonic-crystal optomechanical nanoresonator.

    PubMed

    Makles, K; Antoni, T; Kuhn, A G; Deléglise, S; Briant, T; Cohadon, P-F; Braive, R; Beaudoin, G; Pinard, L; Michel, C; Dolique, V; Flaminio, R; Cagnoli, G; Robert-Philip, I; Heidmann, A

    2015-01-15

    We present the optical optimization of an optomechanical device based on a suspended InP membrane patterned with a 2D near-wavelength grating (NWG) based on a 2D photonic-crystal geometry. We first identify by numerical simulation a set of geometrical parameters providing a reflectivity higher than 99.8% over a 50-nm span. We then study the limitations induced by the finite value of the optical waist and lateral size of the NWG pattern using different numerical approaches. The NWG grating, pierced in a suspended InP 265-nm thick membrane, is used to form a compact microcavity involving the suspended nanomembrane as an end mirror. The resulting cavity has a waist size smaller than 10 μm and a finesse in the 200 range. It is used to probe the Brownian motion of the mechanical modes of the nanomembrane. PMID:25679837

  18. Photonic crystal cavities with metallic Schottky contacts

    SciTech Connect

    Quiring, W.; Al-Hmoud, M.; Reuter, D.; Zrenner, A.; Rai, A.; Wieck, A. D.

    2015-07-27

    We report about the fabrication and analysis of high Q photonic crystal cavities with metallic Schottky-contacts. The structures are based on GaAs n-i membranes with an InGaAs quantum well in the i-region and nanostructured low ohmic metal top-gates. They are designed for photocurrent readout within the cavity and fast electric manipulations. The cavity structures are characterized by photoluminescence and photocurrent spectroscopy under resonant excitation. We find strong cavity resonances in the photocurrent spectra and surprisingly high Q-factors up to 6500. Temperature dependent photocurrent measurements in the region between 4.5 K and 310 K show an exponential enhancement of the photocurrent signal and an external quantum efficiency up to 0.26.

  19. Electric-field-tuned color in photonic crystal elastomers

    NASA Astrophysics Data System (ADS)

    Zhao, Qibin; Haines, Andrew; Snoswell, David; Keplinger, Christoph; Kaltseis, Rainer; Bauer, Siegfried; Graz, Ingrid; Denk, Richard; Spahn, Peter; Hellmann, Goetz; Baumberg, Jeremy J.

    2012-03-01

    Electrically tuned photonic crystals are produced by applying fields across shear-assembled elastomeric polymer opal thin films. At increasing voltages, the polymer opal films stretch biaxially under Maxwell stress, deforming the nanostructure and producing marked color changes. This quadratic electro-optic tuning of the photonic bandgap is repeatable over many cycles, switches within 100 ms, and bridges the gap between electro-active materials and photonic crystals.

  20. Development of a 2D Photonic Crystal Biosensing Platform

    NASA Astrophysics Data System (ADS)

    Baker, James; Sriram, Rashmi; Miller, Benjamin

    2014-03-01

    The importance of early disease diagnosis both for initiating successful clinical treatment and preventing disease transmission continues to propel the development of rapid, ultrasensitive, label-free biosensors. Sensors that implement two-dimensional photonic bandgap crystal structures, in particular, have demonstrated the potential to achieve single-pathogen detection. To reach such high sensitivity, the architecture of the photonic crystal must be designed in a way that pathogen infiltration events are evident in the optical transmission spectrum of the crystal. Computational modeling results are useful both when designing an appropriate photonic crystal geometry and when interpreting experimental observations. Results of ongoing work are presented.

  1. Bio-functionalized hollow core photonic crystal fibers for label-free DNA detection

    NASA Astrophysics Data System (ADS)

    Candiani, A.; Salloom, Hussein T.; Coscelli, E.; Sozzi, M.; Manicardi, A.; Ahmad, Ahmad K.; Al-Janabi, A. Hadi; Corradini, R.; Picchi, G.; Cucinotta, A.; Selleri, S.

    2014-02-01

    Bio-functionalization of inner surfaces of all silica Hollow Core-Photonic Crystal Fibers (HC-PCF) has been investigated. The approach is based on layer-by-layer self-assembly Peptide Nucleic Acid (PNA) probes, which is an oligonucleotide mimic that is well suited for specific DNA target recognition. Two kinds of HC-PCFs have been considered: a photonic Bragg fiber and a hollow core (HC-1060) fiber. After spectral characterization and internal surface functionalization by using PNA probes, genomic DNA solutions from soy flour were infiltrated into the fibers. The experimental results indicate that hybridization of the complementary strand of target DNA increases the thickness of the silica layer and leads up to the generation of surface modes, resulting in a significant modulation of the transmission spectra. Numerical analysis confirms such behavior, suggesting the possibility to realize biological sensing.

  2. Transient Plasma Photonic Crystals for High-Power Lasers.

    PubMed

    Lehmann, G; Spatschek, K H

    2016-06-01

    A new type of transient photonic crystals for high-power lasers is presented. The crystal is produced by counterpropagating laser beams in plasma. Trapped electrons and electrically forced ions generate a strong density grating. The lifetime of the transient photonic crystal is determined by the ballistic motion of ions. The robustness of the photonic crystal allows one to manipulate high-intensity laser pulses. The scheme of the crystal is analyzed here by 1D Vlasov simulations. Reflection or transmission of high-power laser pulses are predicted by particle-in-cell simulations. It is shown that a transient plasma photonic crystal may act as a tunable mirror for intense laser pulses. Generalizations to 2D and 3D configurations are possible. PMID:27314721

  3. Transient Plasma Photonic Crystals for High-Power Lasers

    NASA Astrophysics Data System (ADS)

    Lehmann, G.; Spatschek, K. H.

    2016-06-01

    A new type of transient photonic crystals for high-power lasers is presented. The crystal is produced by counterpropagating laser beams in plasma. Trapped electrons and electrically forced ions generate a strong density grating. The lifetime of the transient photonic crystal is determined by the ballistic motion of ions. The robustness of the photonic crystal allows one to manipulate high-intensity laser pulses. The scheme of the crystal is analyzed here by 1D Vlasov simulations. Reflection or transmission of high-power laser pulses are predicted by particle-in-cell simulations. It is shown that a transient plasma photonic crystal may act as a tunable mirror for intense laser pulses. Generalizations to 2D and 3D configurations are possible.

  4. Optical limiter based on two-dimensional nonlinear photonic crystals

    NASA Astrophysics Data System (ADS)

    Belabbas, Amirouche; Lazoul, Mohamed

    2016-04-01

    The aim behind this work is to investigate the capabilities of nonlinear photonic crystals to achieve ultra-fast optical limiters based on third order nonlinear effects. The purpose is to combine the actions of nonlinear effects with the properties of photonic crystals in order to activate the photonic band according to the magnitude of the nonlinear effects, themselves a function of incident laser power. We are interested in designing an optical limiter based nonlinear photonic crystal operating around 1064 nm and its second harmonic at 532 nm. Indeed, a very powerful solid-state laser that can blind or destroy optical sensors and is widely available and easy to handle. In this work, we perform design and optimization by numerical simulations to determine the better structure for the nonlinear photonic crystal to achieve compact and efficient integrated optical limiter. The approach consists to analyze the band structures in Kerr-nonlinear two-dimensional photonic crystals as a function of the optical intensity. We confirm that these bands are dynamically red-shifted with regard to the bands observed in linear photonic crystals or in the case of weak nonlinear effects. The implemented approach will help to understand such phenomena as intensitydriven optical limiting with Kerr-nonlinear photonic crystals.

  5. Quantification of residual stress from photonic signatures of fused silica

    NASA Astrophysics Data System (ADS)

    Cramer, K. Elliott; Hayward, Maurice; Yost, William T.

    2014-02-01

    A commercially available grey-field polariscope (GFP) instrument for photoelastic examination is used to assess impact damage inflicted upon the outer-most pane of Space Shuttle windows made from fused silica. A method and apparatus for calibration of the stress-optic coefficient using four-point bending is discussed. The results are validated on known material (acrylic) and are found to agree with literature values to within 6%. The calibration procedure is then applied to fused-silica specimens and the stress-optic coefficient is determined to be 2.43 ± 0.54 × 10-12 Pa-1. Fused silica specimens containing impacts artificially made at NASA's Hypervelocity Impact Technology Facility (HIT-F), to simulate damage typical during space flight, are examined. The damage sites are cored from fused silica window carcasses and examined with the GFP. The calibrated GFP measurements of residual stress patterns surrounding the damage sites are presented.

  6. Coupling light in photonic crystal waveguides: A review

    NASA Astrophysics Data System (ADS)

    Dutta, Hemant Sankar; Goyal, Amit Kumar; Srivastava, Varun; Pal, Suchandan

    2016-07-01

    Submicron scale structures with high index contrast are key to compact structures for realizing photonic integrated structures. Ultra-compact optical devices in silicon-on-insulator (SOI) substrates serve compatibility with semiconductor fabrication technology leading to reduction of cost and mass production. Photonic crystal structures possess immense potential for realizing various compact optical devices. However, coupling light to photonic crystal waveguide structures is crucial in order to achieve strong transmission and wider bandwidth of signal. Widening of bandwidth will increase potential for various applications and high transmission will make easy signal detection at the output. In this paper, the techniques reported so far for coupling light in photonic crystal waveguides have been reviewed and analyzed so that a comprehensive guide for an efficient coupling to photonic crystal waveguides can be made possible.

  7. Photonic-crystal slab for terahertz-wave technology platform

    NASA Astrophysics Data System (ADS)

    Fujita, Masayuki

    2016-03-01

    Photonic crystals manipulate photons in a manner analogous to solid-state crystals, and are composed of a dielectric material with a periodic refractive index distribution. In particular, two-dimensional photonic-crystal slabs with high index contrasts (semiconductor/air) are promising for practical applications, owing to the strong optical confinement in simple, thin planar structures. This paper presents the recent progress on a silicon photonic-crystal slab as a technology platform in the terahertz-wave region, which is located between the radio and light wave regions (0.1-10 THz). Extremely low-loss (<0.1 dB/cm) terahertz waveguides based on the photonic-bandgap effect as well as dynamic control and modulation of a terahertz-wave transmission in a photonic-crystal slab by the effective interaction between photoexcited carriers and the terahertz-wave trapping due to the photonic band-edge effect are demonstrated. Terahertz photonic-crystal slabs hold the potential for developing ultralow-loss, compact terahertz components and integrated devices used in applications including wireless communication, spectroscopic sensing, and imaging.

  8. Magneto-photonic crystals for optical sensing applications

    NASA Astrophysics Data System (ADS)

    Dissanayake, Neluka

    Among the optical structures investigated for optical sensing purpose, a significant amount of research has been conducted on photonic crystal based sensors. A particular advantage of photonic crystal based sensors is that they show superior sensitivity for ultra-small volume sensing. In this study we investigate polarization changes in response to the changes in the cover index of magneto-optic active photonic band gap structures. One-dimensional photonic-band gap structures fabricated on iron garnet materials yield large polarization rotations at the band gap edges. The enhanced polarization effects serve as an excellent tool for chemical sensing showing high degree of sensitivity for photonic crystal cover refractive index changes. The one dimensional waveguide photonic crystals are fabricated on single-layer bismuth-substituted rare earth iron garnet films ((Bi, Y, Lu)3(Fe, Ga)5O12 ) grown by liquid phase epitaxy on gadolinium gallium garnet substrates. Band gaps have been observed where Bragg scattering conditions links forward-going fundamental waveguide modes to backscattered high-order waveguide modes. Large near-band-edge polarization rotations which increase progressively with backscattered-mode order have been experimentally demonstrated for multiple samples with different composition, film thickness and fabrication parameters. Experimental findings are supported by theoretical analysis of Bloch modes polarization states showing that large near stop-band edge rotations are induced by the magneto-photonic crystal. Theoretical and experimental analysis conducted on polarization rotation sensitivity to waveguide photonic crystal cover refractive index changes shows a monotonic enhancement of the rotation with cover index. The sensor is further developed for selective chemical sensing by employing Polypyrrole as the photonic crystal cover layer. Polypyrrole is one of the extensively studied conducting polymers for selective analyte detection. Successful

  9. Quantification of Residual Stress from Photonic Signatures of Fused Silica

    NASA Technical Reports Server (NTRS)

    Cramer, K. Elliott; Hayward, Maurice; Yost, William E.

    2013-01-01

    A commercially available grey-field polariscope (GFP) instrument for photoelastic examination is used to assess impact damage inflicted upon the outer-most pane of Space Shuttle windows made from fused silica. A method and apparatus for calibration of the stress-optic coefficient using four-point bending is discussed. The results are validated on known material (acrylic) and are found to agree with literature values to within 6%. The calibration procedure is then applied to fused-silica specimens and the stress-optic coefficient is determined to be 2.43 +/- 0.54 x 10(exp -12)/Pa. Fused silica specimens containing impacts artificially made at NASA's Hypervelocity Impact Technology Facility (HIT-F), to simulate damage typical during space flight, are examined. The damage sites are cored from fused silica window carcasses and examined with the GFP. The calibrated GFP measurements of residual stress patterns surrounding the damage sites are presented. Keywords: Glass, fused silica, photoelasticity, residual stress

  10. Fabrication of substrates for photonic band gap crystals growth

    NASA Astrophysics Data System (ADS)

    Bassène, Seydou; Lessard, Roger A.

    2006-09-01

    We present a technical processing to fabricate substrates (fused silica) for 3-D photonic bandgap material. The potential surface was modified to improve the colloidal method for nanoparticles assembly. This method allows orientating the growth of the colloidal crystals in a specific way; the crystalline plans growth is parallel to the surface of the substrate, and we can eliminate stacking defects and polycrystallinity. The substrate is obtained with ions beam engraving, according to the following process: A layer of photoresist is deposited on the substrate; we write two identical holographic gratings on the photoresist with 90° angle; After the development of photoresist, we obtain a profile which corresponds to one of the crystalline plans of the face centered cubic lattice; This profile will be transferred on the substrate by RIE (reactive ion etching). This substrate has many advantages: it is reusable because it is easily cleaned with solvents like acetone; the same substrate will be easy to use in order to make several growth tests and to optimize physicochemical parameters during artificial opals fabrication.

  11. Photonic crystal channel drop filters based on fractal structures

    NASA Astrophysics Data System (ADS)

    Dideban, Ali; Habibiyan, Hamidreza; Ghafoorifard, Hassan

    2014-09-01

    In this paper we introduce new configurations of channel drop filters based on two-dimensional photonic crystals. Structures consist of two photonic crystal waveguides and a fractal-shaped resonator between them. The effect of structural parameters on resonance frequency and drop efficiency is investigated. Calculations of band structure and propagation of electromagnetic field through devices are done by plane wave expansion (PWE) and finite difference time domain (FDTD) methods, respectively. In our designs more than 95% drop efficiency with quality factor of ~1150 is achievable at wavelength near 1540 nm, which in comparison with other photonic crystal resonator structures is a very satisfactory and acceptable result.

  12. Three dimensional reflectance properties of superconductor-dielectric photonic crystal

    NASA Astrophysics Data System (ADS)

    Pandey, G. N.; Pandey, J. P.; Pandey, U. K.; Sancheti, Bhagyashree; Ojha, S. P.

    2016-05-01

    In this present communication, we have studied the optical properties of Photonics Crystals with super conducting constituent using the TMM method for a stratified medium. We also studied the three dimensional reflectance property of superconductor-dielectric photonic crystal at different temperature and thickness. From above study we show that the superconductor-dielectric photonic crystal may be used as broad band reflector and omnidirectional reflector at low temperature below to the critical temperature. Such property may be applied to make of the reflector which can be used in low temperature region.

  13. Nanomanipulation using silicon photonic crystal resonators.

    PubMed

    Mandal, Sudeep; Serey, Xavier; Erickson, David

    2010-01-01

    Optical tweezers have enabled a number of microscale processes such as single cell handling, flow-cytometry, directed assembly, and optical chromatography. To extend this functionality to the nanoscale, a number of near-field approaches have been developed that yield much higher optical forces by confining light to subwavelength volumes. At present, these techniques are limited in both the complexity and precision with which handling can be performed. Here, we present a new class of nanoscale optical trap exploiting optical resonance in one-dimensional silicon photonic crystals. The trapping of 48 nm and 62 nm dielectric nanoparticles is demonstrated along with the ability to transport, trap, and manipulate larger nanoparticles by simultaneously exploiting the propagating nature of the light in a coupling waveguide and its stationary nature within the resonator. Field amplification within the resonator is shown to produce a trap several orders of magnitude stronger than conventional tweezers and an order of magnitude stiffer than other near-field techniques. Our approach lays the groundwork for a new class of optical trapping platforms that could eventually enable complex all-optical single molecule manipulation and directed assembly of nanoscale material.

  14. Color changing photonic crystals detect blast exposure.

    PubMed

    Cullen, D Kacy; Xu, Yongan; Reneer, Dexter V; Browne, Kevin D; Geddes, James W; Yang, Shu; Smith, Douglas H

    2011-01-01

    Blast-induced traumatic brain injury (bTBI) is the "signature wound" of the current wars in Iraq and Afghanistan. However, with no objective information of relative blast exposure, warfighters with bTBI may not receive appropriate medical care and are at risk of being returned to the battlefield. Accordingly, we have created a colorimetric blast injury dosimeter (BID) that exploits material failure of photonic crystals to detect blast exposure. Appearing like a colored sticker, the BID is fabricated in photosensitive polymers via multi-beam interference lithography. Although very stable in the presence of heat, cold or physical impact, sculpted micro- and nano-structures of the BID are physically altered in a precise manner by blast exposure, resulting in color changes that correspond with blast intensity. This approach offers a lightweight, power-free sensor that can be readily interpreted by the naked eye. Importantly, with future refinement this technology may be deployed to identify soldiers exposed to blast at levels suggested to be supra-threshold for non-impact blast-induced mild TBI.

  15. Optics in Microstructured and Photonic Crystal Fibers

    NASA Astrophysics Data System (ADS)

    Knight, J. C.

    2008-10-01

    The development of optical fibers with two-dimensional patterns of air holes running down their length has reinvigorated research in the field of fiber optics. It has greatly—and fundamentally—broadened the range of specialty optical fibers, by demonstrating that optical fibers can be more "special" than previously thought. Fibers with air cores have made it possible to deliver energetic femtosecond-scale optical pulses, transform limited, as solitons, using single-mode fiber. Other fibers with anomalous dispersion at visible wavelengths have spawned a new generation of single-mode optical supercontinuum sources, spanning visible and near-infrared wavelengths and based on compact pump sources. A third example is in the field of fiber lasers, where the use of photonic crystal fiber concepts has led to a new hybrid laser technology, in which the very high numerical aperture available sing air holes have enabled fibers so short they are more naturally held straight than bent. This paper describes some of the basic physics and technology behind these developments, illustrated with some of the impressive demonstrations of the past 18 months.

  16. Color changing photonic crystals detect blast exposure

    PubMed Central

    Cullen, D. Kacy; Xu, Yongan; Reneer, Dexter V.; Browne, Kevin D.; Geddes, James W.; Yang, Shu; Smith, Douglas H.

    2010-01-01

    Blast-induced traumatic brain injury (bTBI) is the “signature wound” of the current wars in Iraq and Afghanistan. However, with no objective information of relative blast exposure, warfighters with bTBI may not receive appropriate medical care and are at risk of being returned to the battlefield. Accordingly, we have created a colorimetric blast injury dosimeter (BID) that exploits material failure of photonic crystals to detect blast exposure. Appearing like a colored sticker, the BID is fabricated in photosensitive polymers via multi-beam interference lithography. Although very stable in the presence of heat, cold or physical impact, sculpted micro- and nano-structures of the BID are physically altered in a precise manner by blast exposure, resulting in color changes that correspond with blast intensity. This approach offers a lightweight, power-free sensor that can be readily interpreted by the naked eye. Importantly, with future refinement this technology may be deployed to identify soldiers exposed to blast at levels suggested to be supra-threshold for non-impact blast-induced mild TBI. PMID:21040795

  17. Topological Z2 Gapless Photonic Crystals

    NASA Astrophysics Data System (ADS)

    Xie, Biye; Wang, Zidan

    Topological properties of electronic materials with gapless band structure such as Topological Semimetals(TSMs) and Topological Metals(TMs) have drew lots of attention to both theoretical and experimental physicists recently. Although theoretical prediction of TSMs and TMs have been done well, experimental study of them is quite difficult to perform due to the fact that it is very difficult to control and design certain electronic materials. However, since the topological properties stem from the geometric feature, we can study them in Photonic Crystals(PhCs) which are much easy to be controlled and designed. Here we study 2-dimension PhCs consisting of gyrotropic materials with hexagonal structure. In the Brillouin corner, the dispersion relation has gapless points which are similar to Dirac Cones in electronic materials. We firstly derive the effective Hamiltonian of this system and show that if certain perturbation is added to this effective Hamiltonian, this system belongs to AII class according to Altland and Zirbauer topological classification and is described by a Z2 topological charge. Finally we also propose a way to detect this Z2 topological charge using momentum space Aharonov-Bohm interferometer which is firstly proposed by L.Duca and T.Li,etc.

  18. Photonic crystal fiber interferometric vector bending sensor.

    PubMed

    Villatoro, Joel; Minkovich, Vladimir P; Zubia, Joseba

    2015-07-01

    A compact and highly sensitive interferometric bending sensor (inclinometer) capable of distinguishing the bending or inclination orientation is demonstrated. The device operates in reflection mode and consists of a short segment of photonic crystal fiber (PCF) inserted in conventional single-mode optical fiber (SMF). A microscopic collapsed zone in the PCF-SMF junction allows the excitation and recombination of core modes, hence, to build a mode interferometer. Bending on the device induces asymmetric refractive index changes in the PCF core as well as losses. As a result, the effective indices and intensities of the interfering modes are altered, which makes the interference pattern shift and shrink. The asymmetric index changes in the PCF make our device capable of distinguishing the bending orientation. The sensitivity of our sensor is up to 1225 pm/degree and it can be used to monitor small bending angles (±2°). We believe that the attributes of our sensor make it appealing in a number of applications. PMID:26125380

  19. Quantification of residual stress from photonic signatures of fused silica

    SciTech Connect

    Cramer, K. Elliott; Yost, William T.; Hayward, Maurice

    2014-02-18

    A commercially available grey-field polariscope (GFP) instrument for photoelastic examination is used to assess impact damage inflicted upon the outer-most pane of Space Shuttle windows made from fused silica. A method and apparatus for calibration of the stress-optic coefficient using four-point bending is discussed. The results are validated on known material (acrylic) and are found to agree with literature values to within 6%. The calibration procedure is then applied to fused-silica specimens and the stress-optic coefficient is determined to be 2.43 ± 0.54 × 10{sup −12} Pa{sup −1}. Fused silica specimens containing impacts artificially made at NASA’s Hypervelocity Impact Technology Facility (HIT-F), to simulate damage typical during space flight, are examined. The damage sites are cored from fused silica window carcasses and examined with the GFP. The calibrated GFP measurements of residual stress patterns surrounding the damage sites are presented.

  20. Two-pattern compound photonic crystals with a large complete photonic band gap

    SciTech Connect

    Jia Lin; Thomas, Edwin L.

    2011-09-15

    We present a set of two-dimensional aperiodic structures with a large complete photonic band gap (PBG), which are named two-pattern photonic crystals. By superposing two substructures without regard to registration, we designed six new aperiodic PBG structures having a complete PBG larger than 15% for {epsilon}{sub 2}/{epsilon}{sub 1} = 11.4. The rod-honeycomb two-pattern photonic crystal provides the largest complete PBG to date. An aperiodic structure becomes the champion structure with the largest PBG. Surprisingly, the TM and TE gaps of a two-pattern photonic crystal are much less interdependent than the PBGs of conventional photonic crystals proposed before, affording interesting capabilities for us to tune the TM and TE PBGs separately. By altering the respective substructures, optical devices for different polarizations (TE, TM, or both) can readily be designed.

  1. Tunable complete photonic band gap in anisotropic photonic crystal slabs with non-circular air holes using liquid crystals

    NASA Astrophysics Data System (ADS)

    Fathollahi Khalkhali, T.; Bananej, A.

    2016-06-01

    In this study, we analyze the tunability of complete photonic band gap of square and triangular photonic crystal slabs composed of square and hexagonal air holes in anisotropic tellurium background with SiO2 as cladding material. The non-circular holes are infiltrated with liquid crystal. Using the supercell method based on plane wave expansion, we study the variation of complete band gap by changing the optical axis orientation of liquid crystal. Our numerical results show that noticeable tunability of complete photonic band gap can be obtained in both square and triangular structures with non-circular holes.

  2. Negative refraction, subwavelength focusing and beam formation by photonic crystals

    NASA Astrophysics Data System (ADS)

    Ozbay, Ekmel; Aydin, Koray; Bulu, Irfan; Guven, Kaan

    2007-05-01

    We present a review of our experimental and numerical studies on the negative refraction related phenomena in two-dimensional dielectric photonic crystals (PCs). By employing photonic bands with appropriate dispersion, the propagation of the electromagnetic wave through a PC can be controlled to a large extent, and diverse and completely novel electromagnetic phenomena can be generated. We perform the spectral analysis of the negative refraction arising from a convex TM polarized photonic band of a hexagonal PC. As a consequence of negative refraction, we demonstrate a photonic crystal flat lens, which has the ability to focus electromagnetic waves and provide subwavelength resolution laterally. Finally, a photonic crystal with an embedded source is shown to provide a highly directional beam, which can be utilized in certain antenna applications.

  3. Photonic crystals for improving light absorption in organic solar cells

    SciTech Connect

    Duché, D. Le Rouzo, J.; Masclaux, C.; Gourgon, C.

    2015-02-07

    We theoretically and experimentally study the structuration of organic solar cells in the shape of photonic crystal slabs. By taking advantage of the optical properties of photonic crystals slabs, we show the possibility to couple Bloch modes with very low group velocities in the active layer of the cells. These Bloch modes, also called slow Bloch modes (SBMs), allow increasing the lifetime of photons within the active layer. Finally, we present experimental demonstration performed by using nanoimprint to directly pattern the standard poly-3-hexylthiophène:[6,6]-phenyl-C61-butiryc acid methyl ester organic semiconductor blend in thin film form in the shape of a photonic crystal able to couple SBMs. In agreement with the model, optical characterizations will demonstrate significant photonic absorption gains.

  4. Dispersion engineering in nonlinear soft glass photonic crystal fibers infiltrated with liquids.

    PubMed

    Pniewski, Jacek; Stefaniuk, Tomasz; Van, Hieu Le; Long, Van Cao; Van, Lanh Chu; Kasztelanic, Rafał; Stępniewski, Grzegorz; Ramaniuk, Aleksandr; Trippenbach, Marek; Buczyński, Ryszard

    2016-07-01

    We present a numerical study of the dispersion characteristic modification of nonlinear photonic crystal fibers infiltrated with liquids. A photonic crystal fiber based on the soft glass PBG-08, infiltrated with 17 different organic solvents, is proposed. The glass has a light transmission window in the visible-mid-IR range of 0.4-5 μm and has a higher refractive index than fused silica, which provides high contrast between the fiber structure and the liquids. A fiber with air holes is designed and then developed in the stack-and-draw process. Analyzing SEM images of the real fiber, we calculate numerically the refractive index, effective mode area, and dispersion of the fundamental mode for the case when the air holes are filled with liquids. The influence of the liquids on the fiber properties is discussed. Numerical simulations of supercontinuum generation for the fiber with air holes only and infiltrated with toluene are presented. PMID:27409187

  5. Pendellösung effect in photonic crystals

    NASA Astrophysics Data System (ADS)

    Savo, S.; di Gennaro, E.; Miletto, C.; Andreone, A.; Dardano, P.; Moretti, L.; Mocella, V.

    2008-06-01

    At the exit surface of a photonic crystal, the intensity of the diffracted wave can be periodically modulated, showing a maximum in the "positive" (forward diffracted) or in the "negative" (diffracted) direction, depending on the slab thickness. This thickness dependence is a direct result of the so-called Pendellosung phenomenon, consisting of the periodic exchange inside the crystal of the energy between direct and diffracted beams. We report the experimental observation of this effect in the microwave region at about 14 GHz by irradiating 2D photonic crystal slabs of different thickness and detecting the intensity distribution of the electromagnetic field at the exit surface and inside the crystal itself.

  6. Higher-order photon correlations in pulsed photonic crystal nanolasers

    SciTech Connect

    Elvira, D.; Hachair, X.; Braive, R.; Beaudoin, G.; Robert-Philip, I.; Sagnes, I.; Abram, I.; Beveratos, A.; Verma, V. B.; Baek, B.; Nam, S. W.; Stevens, M. J.; Dauler, E. A.

    2011-12-15

    We report on the higher-order photon correlations of a high-{beta} nanolaser under pulsed excitation at room temperature. Using a multiplexed four-element superconducting single-photon detector we measured g{sup (n)}(0-vector) with n=2,3,4. All orders of correlation display partially chaotic statistics, even at four times the threshold excitation power. We show that this departure from coherence and Poisson statistics is due to the quantum fluctuations associated with the small number of photons at the lasing threshold.

  7. Photonic-crystal time-domain simulations using Wannier functions.

    PubMed

    Blum, Christian; Wolff, Christian; Busch, Kurt

    2011-01-15

    We present a Wannier-function-based time-domain method for photonic-crystal integrated optical circuits. In contrast to other approaches, this method allows one to trade CPU time against memory consumption and therefore is particularly well suited for the treatment of large-scale systems. As an illustration, we apply the method to the design of a photonic-crystal-based sensor, which utilizes a dual Mach-Zehnder-Fano interferometer. PMID:21263535

  8. Use of a photonic crystal for optical amplifier gain control

    DOEpatents

    Lin, Shawn-Yu; Fleming, James G.; El-Kady, Ihab

    2006-07-18

    An optical amplifier having a uniform gain profile uses a photonic crystal to tune the density-of-states of a gain medium so as to modify the light emission rate between atomic states. The density-of-states of the gain medium is tuned by selecting the size, shape, dielectric constant, and spacing of a plurality of microcavity defects in the photonic crystal. The optical amplifier is particularly useful for the regeneration of DWDM signals in long optical fibers.

  9. Semiclassical model of stimulated Raman scattering in photonic crystals.

    PubMed

    Florescu, Lucia; Zhang, Xiang

    2005-07-01

    We study the stimulated Raman scattering (SRS) of light from an atomic system embedded in a photonic crystal and coherently pumped by a laser field. In our study, the electromagnetic field is treated classically and the atomic system is described quantum mechanically. Considering a decomposition of the pump and Stokes fields into the Bloch modes of the photonic crystals and using a multiscale analysis, we derive the Maxwell-Bloch equations for SRS in photonic crystals. These equations contain effective parameters that characterize the SRS gain, the nonlinear atomic response to the electromagnetic field, and the group velocity and that can be calculated in terms of the Bloch modes of the unperturbed photonic crystal. We show that if the pump laser frequency is tuned near a photonic band edge and the atomic system is carefully chosen such that the Stokes mode matches another photonic band edge, low-threshold, enhanced Raman amplification is possible. Possible physical realizations of SRS in photonic crystals are also discussed.

  10. Polarisation singularities in photonic crystals for an on-chip spin-photon interface

    NASA Astrophysics Data System (ADS)

    Beggs, Daryl M.; Young, Andrew B.; Thijssen, Arthur C. T.; Oulton, Ruth

    2015-03-01

    Integrated quantum photonic chips are a leading contender for future quantum technologies, which aim to use the entanglement and superposition properties of quantum physics to speed up the manipulation of data. Quantum information may be stored and transmitted in photons, which make excellent flying qubits. Photons suffer little from decoherence, and single qubit gates performed by changing photon phase, are straightforward. Less straightforward is the ability to create two qubit gates, where one photon is used to switch another's state; inherently difficult due to the extremely small interaction cross-section between photons. The required deterministic two-qubit interactions will likely need a hybrid scheme with the ``flying'' photonic qubit interacting with a ``static'' matter qubit. Here we present the design of a photonic crystal waveguide structure that can couple electron-spin to photon path, thus providing an interface between a static and a flying qubit. We will show that the complex polarization properties inherent in the photonic crystal eigenmodes supports polarization singularities - positions in the electric field vector where one of the parameters describing the local polarization ellipse is singular - and that these singularities are ideal for a range of quantum information applications. In particular, we will show that by placing a quantum dot at one of these singularities, the electron-spin becomes correlated with the photon emission direction, creating an in-plane spin-photon interface that can transfer quantum information from static to flying qubits.

  11. Power dependent pulse delay with asymmetric dual-core hybrid photonic crystal fiber coupler

    NASA Astrophysics Data System (ADS)

    Jing, Qi; Zhang, Xia; Wei, Wei; Huang, Yongqing; Ren, Xiaomin

    2014-02-01

    We propose a novel asymmetric dual-core hybrid photonic crystal fiber (PCF) coupler composed of a silicon tube as the left core and a silica core as the right core. The control of picosecond pulse delay is achievable by means of power adjusting. The transmission modes, dispersion characteristics and coupling coefficients of the proposed coupler are investigated numerically. The results demonstrate that it is possible to obtain 2.0 ps time delay for soliton pulse with 2.0 ps temporal width within 1 cm length. Further numerical results show that the coupler can generate 10.0 ps undistorted time advance within 5 cm length.

  12. Two-dimensional colloid-based photonic crystals for distributed feedback polymer lasers

    SciTech Connect

    Mafouana, Rodrigue; Rehspringer, Jean-Luc; Hirlimann, Charles; Estournes, Claude; Dorkenoo, Kokou D.

    2004-11-08

    We report on a process to design highly ordered monolayers of two-dimensional photonic crystals, made of silica nanoparticules, that can be used for the development of organic optical devices. We have used a photopolymerization process to incorporate a dye gain medium into the nanoparticle layers in order to achieve a laser cavity. The high spatial coherence of the deposits allows for single-mode laser emission in the plane of the layer when the light excitation is perpendicular to the plane. Such periodic films should help in reducing the number of layers needed for future electrically pumped distributed feedback lasers.

  13. Chalcogenide glass-based three-dimensional photonic crystals

    NASA Astrophysics Data System (ADS)

    Feigel, A.; Kotler, Z.; Sfez, B.; Arsh, A.; Klebanov, M.; Lyubin, V.

    2000-11-01

    AsSeTe chalcogenide glasses are materials that are photosensitive and have a large refractive index. These properties make these glasses particularly suitable for the fabrication of photonic crystals. We present a way to build three-dimensional photonic structures from chalcogenide glasses using vapor deposition and direct holographic writing. We show that this technique is intrinsically self-aligned, providing a simple way to build layer-by-layer photonic crystals and a four-layer structure demonstrating the principle of the technique.

  14. Photonic crystals, light manipulation, and imaging in complex nematic structures

    NASA Astrophysics Data System (ADS)

    Ravnik, Miha; Å timulak, Mitja; Mur, Urban; Čančula, Miha; Čopar, Simon; Žumer, Slobodan

    2016-03-01

    Three selected approaches for manipulation of light by complex nematic colloidal and non-colloidal structures are presented using different own custom developed theoretical and modelling approaches. Photonic crystals bands of distorted cholesteric liquid crystal helix and of nematic colloidal opals are presented, also revealing distinct photonic modes and density of states. Light propagation along half-integer nematic disclinations is shown with changes in the light polarization of various winding numbers. As third, simulated light transmission polarization micrographs of nematic torons are shown, offering a new insight into the complex structure characterization. Finally, this work is a contribution towards using complex soft matter in optics and photonics for advanced light manipulation.

  15. Spontaneous emission from photonic crystals: full vectorial calculations

    PubMed

    Li; Lin; Zhang

    2000-05-01

    Quantum electrodynamics of atom spontaneous emission from a three-dimensional photonic crystal is studied in a full vectorial framework. The electromagnetic fields are quantized via solving the eigenproblem of photonic crystals with use of a plane-wave expansion method. It is found that the photon density of states and local density of states (LDOS) with a full band gap vary slowly near the edge of band gap, in significant contrast to the singular character predicted by the previous isotropic model. Therefore, the spontaneous emission can be solved by conventional Weisskopf-Wigner approximate theory, which yields a pure exponentially decaying behavior with a rate proportional to the LDOS.

  16. Alignment of crystal orientations of the multi-domain photonic crystals in Parides sesostris wing scales.

    PubMed

    Yoshioka, S; Fujita, H; Kinoshita, S; Matsuhana, B

    2014-03-01

    It is known that the wing scales of the emerald-patched cattleheart butterfly, Parides sesostris, contain gyroid-type photonic crystals, which produce a green structural colour. However, the photonic crystal is not a single crystal that spreads over the entire scale, but it is separated into many small domains with different crystal orientations. As a photonic crystal generally has band gaps at different frequencies depending on the direction of light propagation, it seems mysterious that the scale is observed to be uniformly green under an optical microscope despite the multi-domain structure. In this study, we have carefully investigated the structure of the wing scale and discovered that the crystal orientations of different domains are not perfectly random, but there is a preferred crystal orientation that is aligned along the surface normal of the scale. This finding suggests that there is an additional factor during the developmental process of the microstructure that regulates the crystal orientation. PMID:24352678

  17. Geometric Potential and Transport in Photonic Topological Crystals

    SciTech Connect

    Szameit, Alexander; Dreisow, Felix; Heinrich, Matthias; Keil, Robert; Nolte, Stefan; Tuennermann, Andreas; Longhi, Stefano

    2010-04-16

    We report on the experimental realization of an optical analogue of a quantum geometric potential for light wave packets constrained on thin dielectric guiding layers fabricated in silica by the femtosecond laser writing technology. We further demonstrate the optical version of a topological crystal, with the observation of Bloch oscillations and Zener tunneling of a purely geometric nature.

  18. Blue shift of laser mode in photonic crystal microcavity

    NASA Astrophysics Data System (ADS)

    Zhao, Pengchao; Feng, Z. G.; Qi, Fan; Qi, Aiyi; Wang, Yufei; Zheng, W. H.

    2014-11-01

    We report the first demonstration of blue shift of optical pumping photonic crystal (PhC) laser. A femtosecond laser was used to pump the InGaAsP based two dimensional photonic crystal laser at room temperature. Linear dependence of the resonance wavelength with respect to the pump power is observed: dλ/dP=-1.5×10-2 nm/μW . Blue shift of overall 1.1nm was obtained with the increase power of pump laser. These results are in agreement with theoretical expectation while the carrier-induced index change is introduced into the PhC semiconductor laser. It shows a possibility that by proper wafer design and careful optimization, we may obtain wavelength stable photonic crystal laser, which is important in photonic integration.

  19. Electrical control of silicon photonic crystal cavity by graphene.

    PubMed

    Majumdar, Arka; Kim, Jonghwan; Vuckovic, Jelena; Wang, Feng

    2013-02-13

    The efficient conversion of an electrical signal to an optical signal in nanophotonics enables solid state integration of electronics and photonics. The combination of graphene with photonic crystals is promising for electro-optic modulation. In this paper, we demonstrate that by electrostatic gating a single layer of graphene on top of a photonic crystal cavity, the cavity resonance can be changed significantly. A ~2 nm change in the cavity resonance line width and almost 400% (6 dB) change in resonance reflectivity is observed. In addition, our analysis shows that a graphene-photonic crystal device can potentially be useful for a high speed and low power absorptive and refractive modulator, while maintaining a small physical footprint.

  20. Design, fabrication and transmitted properties of terahertz paper photonic crystals.

    PubMed

    Zhang, Wentao; Lin, Xian; Jin, Zuanming; Ma, Guohong; Zhong, Minjian

    2013-11-18

    The terahertz paper photonic crystals, including one-dimensional stacks, two-dimensional square and hexagonal lattices as well as three-dimensional body-centered cubic lattice, are designed and fabricated. Femtosecond laser direct writing is employed to process paper layers. The transmission properties of these photonic crystals in THz range are characterized using time-domain THz spectroscopy. The experimental results are in good agreement with the numerical simulations and well explained by the photonic band-structure calculated by the plane wave expansion method. Our results demonstrate that paper photonic crystals have a good performance on molding the flow of THz radiation. From another point of view, the fabrication method proposed in this work can be widely extended to manufacture different micro-structures on various materials.

  1. Hybrid genetic optimization for design of photonic crystal emitters

    NASA Astrophysics Data System (ADS)

    Rammohan, R. R.; Farfan, B. G.; Su, M. F.; El-Kady, I.; Reda Taha, M. M.

    2010-09-01

    A unique hybrid-optimization technique is proposed, based on genetic algorithms (GA) and gradient descent (GD) methods, for the smart design of photonic crystal (PhC) emitters. The photonic simulation is described and the granularity of photonic crystal dimensions is considered. An innovative sliding-window method for performing local heuristic search is demonstrated. Finally, the application of the proposed method on two case studies for the design of a multi-pixel photonic crystal emitter and the design of thermal emitter in thermal photovoltaic is demonstrated. Discussion in the report includes the ability of the optimal PhC structures designed using the proposed method, to produce unprecedented high emission efficiencies of 54.5% in a significantly long wavelength region and 84.9% at significantly short wavelength region.

  2. Efficient method for recycling silica materials from waste powder of the photonic industry.

    PubMed

    Lin, Liang-Yi; Bai, Hsunling

    2013-05-01

    An efficient and economic approach is proposed for the fast and direct recovery of silica materials from photonic waste powder. Unlike the conventional alkaline fusion method for the extraction of silica from waste materials, this method possesses advantages of a rapid and low-energy-consumed process with total recovery yield. The obtained mesoporous silica material, denoted as MCM-41(DU)-F, was recovered directly from photonic waste powder at room temperature with the assistance of cationic surfactant, hydrofluoric acid, and ammonia hydroxide. The recycled MCM-41(DU)-F with a high specific surface area (788 m(2)/g), ordered mesoporous structure (4.5 nm), and large pore volume (1.1 cm(3)/g) was used as support of tetraethylenepentamine (TEPA) for the capture of CO2 from a flue gas stream. The results demonstrated that TEPA-impregnated MCM-41(DU)-F had an adsorption capacity of 120 mg of CO2/g of adsorbent. This is higher than the amount adsorbed by TEPA-MCM-41(NaSi) made from pure chemicals (113 mg of CO2/g of adsorbent) and TEPA-MCM-41(AF) made from alkaline fusion (112 mg of CO2/g of adsorbent) under the same testing conditions. This novel recycling process, which can improve cost effectiveness for the mass production of valuable mesoporous silica materials from cheap and abundant resources through convenient preparation steps, is surely beneficial from the viewpoint of economical use of photonic industrial waste powder.

  3. Multicolor upconversion emissions in Tm 3+/Er3+ codoped tellurite photonic microwire between silica fiber tapers.

    PubMed

    Chen, Nan-Kuang; Kuan, Pei-Wen; Zhang, Junjie; Zhang, Liyan; Hu, Lili; Lin, Chinlon; Tong, Limin

    2010-12-01

    We report multicolor upconversion emissions including the blue-violet, green, and red lights in a Tm 3+/Er3+codoped tellurite glass photonic microwire between two silica fiber tapers. A silica fiber is tapered until its evanescent field is exposed and then angled-cleaved at the tapered center to divide the tapered fibers into two parts. A tellurite glass is melted by a gas flame to cluster into a sphere at the tip of one tapered fiber. The other angled-cleaved tapered fiber is blended into the melted tellurite glass. When the tellurite glass is melted, the two silica fiber tapers are simultaneously moving outwards to draw the tellurite glass into a microwire in between. The advantage of angled-cleaving on fiber tapers is to avoid cavity resonances in high index photonic microwire. Thus, the broadband white light can be transmitted between silica fibers and a special optical property like high intensity upconversion emission can be achieved. A cw 1064 nm Nd:YAG laser light is launched into the Tm 3+/Er3+ codoped tellurite microwire through a silica fiber taper to generate the multicolor upconversion emissions, including the blue-violet, green, and red lights, simultaneously. PMID:21164907

  4. Manipulating light propagation and emission using photonic crystals

    SciTech Connect

    Nair, Rajesh V.; Jagatap, B. N.

    2014-03-31

    We discuss the synthesis and characterization of self-assembled photonic crystals using polymer colloids having sub-micron diameters. The angle resolved optical reflectivity measurements indicate the hybridization between stop gaps in the multiple Bragg diffraction regimes. Each diffraction resonances in the multiple Bragg diffraction regimes are assigned to respective crystal planes. We also discuss laser-induced studies of spontaneous emission in self-assembled photonic crystals having Rhodamine-B dye doped colloids. Our experimental results reveal more than 51% inhibition in emission intensity within the stop gap as compared to a proper reference sample.

  5. Controllable light diffraction in woodpile photonic crystals filled with liquid crystal

    SciTech Connect

    Ho, Chih-Hua; Zeng, Hao; Wiersma, Diederik S.; Cheng, Yu-Chieh; Maigyte, Lina; Trull, Jose; Cojocaru, Crina; Staliunas, Kestutis

    2015-01-12

    An approach to switching between different patterns of light beams transmitted through the woodpile photonic crystals filled with liquid crystals is proposed. The phase transition between the nematic and isotropic liquid crystal states leads to an observable variation of the spatial pattern transmitted through the photonic structure. The transmission profiles in the nematic phase also show polarization sensibility due to refractive index dependence on the field polarization. The experimental results are consistent with a numerical calculation by Finite Difference Time Domain method.

  6. Photonic crystal engineering in glancing angle deposition thin films

    NASA Astrophysics Data System (ADS)

    Jensen, Hans Martin Overgaard

    2005-11-01

    From living rooms to operating rooms, our world is becoming dependent on information technology. For half a century a transformation in computing and communications has been borne by semiconductor microelectronics, but to serve us tomorrow, new materials transcending the performance and cost of current technology must be developed. An emerging optical material is the photonic bandgap crystal, which so fundamentally manipulates the emission and propagation of light that photons may be harnessed to eclipse what electronics accomplish today. However, the crystals consist of intricate, sub micrometre structures that are complex to fabricate, and even harder to engineer for technological applications. Indeed, fabrication challenges have inhibited photonic crystal progress. This thesis responds by enabling photonic crystal engineering through a chiral thin film fabrication technique known as glancing angle deposition. By oblique vapour deposition onto rotating substrates, the approach creates tetragonal lattices of square spirals with widths of a few hundred nanometres, predicted to yield strong photonic bandgaps at useful optical wavelengths. Within the scope of the thesis research, high resolution, high density direct write lithography is developed to deliver large area crystal substrates with extensive design freedom. The evolution of square spiral photonic crystal thin films on such substrates is analyzed, and new deposition methods are devised to allow engineering of the photonic bandgap by reducing the dimensions and enhancing the fine structure of the square spirals. Optical characterization is performed to evaluate the presence of a complete, three dimensional photonic bandgap, confirm an engineered bandgap at 1.65 mum, and quantify the improvement in crystal quality to a bandgap width of 10.9%. With a potential for use as photonic waveguides, the engineering of embedded, functional air and dielectric defects is also established. Furthermore, the thesis develops

  7. Development of 3D photonic crystals using sol-gel process for high power laser applications

    NASA Astrophysics Data System (ADS)

    Benoit, F.; Dieudonné, E.; Bertussi, B.; Vallé, K.; Belleville, P.; Mallejac, N.; Enoch, S.; Sanchez, C.

    2015-08-01

    Three-dimensional photonic crystals (PCs) are periodic materials with a modulated refractive index on a length scale close to the light wavelength. This optical property allows the preparation of specific optical components like highly reflective mirrors. Moreover, these structured materials are known to have a high laser-induced damage threshold (LIDT) in the sub-nanosecond range compared to multi-layered dielectric mirrors. This property is obtained because only one high LIDT material (silica) is used. The second material used in the layer stack is replaced by air. In this work, we present the development of 3D PCs with narrow-sized colloidal silica particles, prepared by sol-gel process and deposited with Langmuir-Blodgett technique. Different syntheses routes have been investigated and compared regarding the optical properties of the PCs. Finally a numerical model based on an ideal opal network including defect influence is used to explain these experimental results.

  8. Control over the distribution of luminescent impurities inside opal photonic crystals

    NASA Astrophysics Data System (ADS)

    Klimonsky, Sergey; Knotko, Alexander; Borodinov, Nikolay; Eliseev, Andrey

    2015-09-01

    The work is focused on the problem of control over the distribution of emitting centers inside photonic crystals. Two ways of luminescent impurity incorporation into synthetic silica opals are considered. First is based on the infiltration of the opal with a water solution of organic complexes (HEuEDTA) and leads to a formation of a uniform luminescent layer on the surface of silica microspheres. The other involves the infiltration of the structure with a heptane solution of CdSe quantum dots leading to the localization of the luminescent component around contact points between microspheres. Thus two different types of strongly ordered distribution of luminescent component inside opal can be obtained. Corresponding samples were prepared and their optical properties are discussed.

  9. Photon Cascade from a Single Crystal Phase Nanowire Quantum Dot.

    PubMed

    Bouwes Bavinck, Maaike; Jöns, Klaus D; Zieliński, Michal; Patriarche, Gilles; Harmand, Jean-Christophe; Akopian, Nika; Zwiller, Val

    2016-02-10

    We report the first comprehensive experimental and theoretical study of the optical properties of single crystal phase quantum dots in InP nanowires. Crystal phase quantum dots are defined by a transition in the crystallographic lattice between zinc blende and wurtzite segments and therefore offer unprecedented potential to be controlled with atomic layer accuracy without random alloying. We show for the first time that crystal phase quantum dots are a source of pure single-photons and cascaded photon-pairs from type II transitions with excellent optical properties in terms of intensity and line width. We notice that the emission spectra consist often of two peaks close in energy, which we explain with a comprehensive theory showing that the symmetry of the system plays a crucial role for the hole levels forming hybridized orbitals. Our results state that crystal phase quantum dots have promising quantum optical properties for single photon application and quantum optics. PMID:26806321

  10. Tunable optical anisotropy in three-dimensional photonic crystals

    SciTech Connect

    Che Ming; Li Zhiyuan; Liu Rongjuan

    2007-08-15

    Artificial optical birefringence can be realized in three-dimensional photonic crystals with a uniaxial structural symmetry: e.g., woodpile photonic crystals with a tetragonal lattice structure in the long-wavelength limit. The ordinary and extraordinary indices of refraction are determined from calculation of the reflection coefficient for a plane wave incident on the surface of a semi-infinite photonic crystal at different angles. We find that the anisotropy can be widely tuned by simply changing the width and thickness of the dielectric rod. A large relative negative anisotropy over 33% is found. A transition from positive anisotropy to negative anisotropy can be readily achieved. At certain parameters, a structurally anisotropic nanostructure can behave like an optically isotropic medium. Our study opens a window to use artificial nanostructures to create an arbitrary optical anisotropy that is not possible in natural crystals.

  11. Controlling single-photon transport with three-level quantum dots in photonic crystals

    NASA Astrophysics Data System (ADS)

    Yan, Cong-Hua; Jia, Wen-Zhi; Wei, Lian-Fu

    2014-03-01

    We investigate how to control single-photon transport along the photonic crystal waveguide with the recent experimentally demonstrated artificial atoms [i.e., Λ-type quantum dots (QDs)] [S. G. Carter et al., Nat. Photon. 7, 329 (2013), 10.1038/nphoton.2013.41] in an all-optical way. Adopting full quantum theory in real space, we analytically calculate the transport coefficients of single photons scattered by a Λ-type QD embedded in single- and two-mode photonic crystal cavities (PCCs), respectively. Our numerical results clearly show that the photonic transmission properties can be exactly manipulated by adjusting the coupling strengths of waveguide-cavity and QD-cavity interactions. Specifically, for the PCC with two degenerate orthogonal polarization modes coupled to a Λ-type QD with two degenerate ground states, we find that the photonic transmission spectra show three Rabi-splitting dips and the present system could serve as single-photon polarization beam splitters. The feasibility of our proposal with the current photonic crystal technique is also discussed.

  12. Direct-write assembly of three-dimensional polyelectrolyte scaffolds, inorganic hybrids, and photonic crystals

    NASA Astrophysics Data System (ADS)

    Xu, Mingjie

    Polyamine-rich complexes are developed for microscale patterning of planar and 3-D structures by direct ink writing. The complexes are formed by mixing poly(allylamine) hydrochloride and poly(acrylic acid) sodium salt in water in a non-stoichiometric ratio. Their phase behavior, rheological properties, and coagulation behavior in alcohol-water reservoirs are characterized. Direct comparisons are made between these complexes, which are based on mixtures of linear polyelectrolytes, to prior observations of complexes composed of linear and highly branched chains. The optimal polyamine-rich ink and reservoir compositions are identified for direct-write assembly of wavy, gradient, and 3-D micro-periodic architectures. The morphology of these coagulated ink filaments is revealed by oxygen plasma etching. Silica-polymer hybrid structures that mimic natural occurring diatoms are created by combining direct-write assembly of polyamine-rich scaffolds with biomimetic silicification. The influence of ink composition, solution pH, and immersion protocol on the silica content is investigated. The reaction kinetics is studied by measuring the silica content as a function of the silicification time, which suggests that the biomimetic silicification of polyamine-rich scaffolds is a diffusion-limited process. The distribution of silica is found to be uniform throughout within the 3D scaffolds. These silicified hybrid structures exhibit improved thermal and mechanical stability by maintaining their structural integrity even upon complete removal of the polymer phase by heating to 1000°C. Photonic crystals composed of a germanium hollow-woodpile architecture are created by replicating 3D microperiodic polymer scaffolds assembled by direct ink writing. First, polymer woodpiles with a face-centered tetragonal geometry are fabricated by direct ink writing. Chemical vapor depositions of silica and germanium are then performed under controlled conditions to produce optimal layer

  13. Photonic crystal fiber monitors for intracellular ice formation

    NASA Astrophysics Data System (ADS)

    Battinelli, Emily; Reimlinger, Mark; Wynne, Rosalind

    2012-04-01

    An all-silica steering wheel photonic crystal fiber (SW-PCF) device with real-time analysis for cellular temperature sensing is presented. Results are provided for water-filled SW-PCF fibers experiencing cooling down near -40°C. Cellular temperature sensors with fast response times are of interest particularly to the study of cryopreservation, which has been influential in applications such as tissue preservation, food quality control, genetic engineering, as well as drug discovery and in- vitro toxin testing. Results of this investigation are relevant to detection of intracellular ice formation (IIF) and better understanding cell freezing at very low temperatures. IIF detection is determined as a function of absorption occurring within the core of the SW-PCF. The SW-PCF has a 3.3μm core diameter, 125μm outer diameter and steering wheel-like air hole pattern with triangular symmetry, with a 20μm radius. One end of a 0.6m length of the SW-PCF is placed between two thermoelectric coolers, filled with ~0.1μL water. This end is butt coupled to a 0.5m length of single mode fiber (SMF), the distal end of the fiber is then inserted into an optical spectrum analyzer. A near-IR light source is guided through the fiber, such that the absorption of the material in the core can be measured. Spectral characteristics demonstrated by the optical absorption of the water sample were present near the 1300-1700nm window region with strongest peaks at 1350, 1410 and 1460nm, further shifting of the absorption peaks is possible at cryogenic temperatures making this device suitable for IIF monitoring applications.

  14. Research on interferometric photonic crystal fiber hydrophone

    NASA Astrophysics Data System (ADS)

    Luo, Hong; Zhang, Zhen-hui; Wang, Fu-yin; Xiong, Shui-dong

    2013-08-01

    Current research on photonic crystal fiber (PCF) for acoustic sensing was focused on the PCF's pressure sensitivity enhancement. However, whether the enhancement of the PCF's pressure sensitivity can be actually realized is still controversial. Practical hydrophone, utilizing PCFs, to manifest its superior sensitivity to normal single mode fibers (SMFs) for acoustic sensing, should be made. Account to this point of view, actual hydrophone was fabricated. Index guiding PCF was used, the fiber core is solid silicon dioxide (SiO2), and the cladding is SiO2 filled with lots of periodical transverse circular air hollows. The PCF, mounted on an air-backed mandrel for structural sensitivity enhancement, was used as a sensing arm of the fiber Michelson interferometer. The other arm, so called reference arm, was made of SMF. Faraday rotator mirrors (FRM) were spliced in the end of each interferometric arm account for polarization induced phase fading, which is a common scheme in fiber interferometric sensing systems. A similar hydrophone, with all the same structure except that the PCF was exchanged into SMF, was also fabrication to make the contrast. The narrowlinewidth and frequency-tunable optical fiber laser was used to achieve high accuracy optical interferometric measurement. Meanwhile, the phase generated carrier (PGC) modulation-demodulation scheme was adopted to interrogate the measurand signal. Experiment was done by using acoustic standing-wave test apparatus. Linearity characteristics of the two hydrophones were measured at frequency 100Hz, 500Hz, and 1000Hz, experimental results showed that the maximum error of the linearity was 10%, a little larger than the theoretical results. Pressure sensitivities of the PCF hydrophone and the SMF hydrophone were measured using a reference standard PZT hydrophone in the frequency range from 20 Hz to 1600 Hz, the measurement data showed that the sensitivity of the PCF hydrophone was about -162.8 dB re. rad/μPa, with a

  15. Optical nonlinearities near single photon level with a quantum dot coupled to a photonic crystal cavity

    NASA Astrophysics Data System (ADS)

    Sridharan, Deepak

    Over the last decade, exponential increase of information bandwidth over the internet and other communication media has increased the total power consumed by the devices associated with information exchange. With ever increasing number of users, and packing of a higher number of devices onto a chip, there is a great need for reduction in not only the power consumption of the devices but also the costs associated with information transfer. Currently, the benchmark in the energy consumption per logic operation is at femtojoule level and is set by the CMOS industry. However, optical devices based on single photon emitters coupled to a microcavity have the potential to reduce the optical power dissipation down to attojoule levels wherein only few 10s of photons are consumed for a logic operation. This work presents our theoretical and experimental efforts towards realization of all optical device based on the enhanced nonlinearities of a single photon emitter in a photonic crystal cavity. We show that a single quantum dot coupled to a photonic crystal cavity can be used to route an incoming optical beam with optical power dissipation of 14 attojoules, corresponding to only 65 photons. This value is well below the operational level for current CMOS devices indicating the potential for chip based optical transistors for reduction in energy consumption. The single photon emitters that we use to create the nonlinearity are the quantum dots, which are semiconductor nanostructures that exhibit a discrete energy spectrum. The interaction of the quantum dot, with light confined inside a photonic crystal cavity, results in strong atom-photon interactions which can be used for ultra-low power all optical switching. The strong interactions between a quantum dot and photonic crystal cavity can be further utilized to realize quantum computation schemes on a chip. I also describe techniques for integrating this transistor into an optical circuit, and discuss methods for post

  16. Magnetic assembly of nonmagnetic particles into photonic crystal structures.

    PubMed

    He, Le; Hu, Yongxing; Kim, Hyoki; Ge, Jianping; Kwon, Sunghoon; Yin, Yadong

    2010-11-10

    We report the rapid formation of photonic crystal structures by assembly of uniform nonmagnetic colloidal particles in ferrofluids using external magnetic fields. Magnetic manipulation of nonmagnetic particles with size down to a few hundred nanometers, suitable building blocks for producing photonic crystals with band gaps located in the visible regime, has been difficult due to their weak magnetic dipole moment. Increasing the dipole moment of magnetic holes has been limited by the instability of ferrofluids toward aggregation at high concentration or under strong magnetic field. By taking advantage of the superior stability of highly surface-charged magnetite nanocrystal-based ferrofluids, in this paper we have been able to successfully assemble 185 nm nonmagnetic polymer beads into photonic crystal structures, from 1D chains to 3D assemblies as determined by the interplay of magnetic dipole force and packing force. In a strong magnetic field with large field gradient, 3D photonic crystals with high reflectance (83%) in the visible range can be rapidly produced within several minutes, making this general strategy promising for fast creation of large-area photonic crystals using nonmagnetic particles as building blocks.

  17. 3D holographic polymer photonic crystal for superprism application

    NASA Astrophysics Data System (ADS)

    Chen, Jiaqi; Jiang, Wei; Chen, Xiaonan; Wang, Li; Zhang, Sasa; Chen, Ray T.

    2007-02-01

    Photonic crystal based superprism offers a new way to design new optical components for beam steering and DWDM application. 3D photonic crystals are especially attractive as they could offer more control of the light beam based on the needs. A polygonal prism based holographic fabrication method has been demonstrated for a three-dimensional face-centered-cubic (FCC)-type submicron polymer photonic crystal using SU8 as the photo-sensitive material. Therefore antivibration equipment and complicated optical alignment system are not needed and the requirement for the coherence of the laser source is relaxed compared with the traditional holographic setup. By changing the top-cut prism structure, the polarization of the laser beam, the exposure and development conditions we can achieve different kinds of triclinic or orthorhombic photonic crystals on demand. Special fabrication treatments have been introduced to ensure the survivability of the fabricated large area (cm2) nano-structures. Scanning electron microscopy and diffraction results proved the good uniformity of the fabricated structures. With the proper design of the refraction prism we have achieved a partial bandgap for S+C band (1460-1565nm) in the [111] direction. The transmission and reflection spectra obtained by Fourier transform infrared spectroscopy (FTIR) are in good agreement with simulated band structure. The superprism effects around 1550nm wavelength for the fabricated 3D polymer photonic crystal have been theoretically calculated and such effects can be used for beam steering purpose.

  18. Tunable negative-index photonic crystals using colloidal magnetic fluids

    NASA Astrophysics Data System (ADS)

    Geng, Tao; Wang, Xin; Wang, Yan; Dong, Xiang-Mei

    2015-12-01

    The model of using colloidal magnetic fluid to build tunable negative-index photonic crystal is established. The effective permittivity ɛe and permeability μe of the two-dimensional photonic crystal are investigated in detail. For transverse magnetic polarization, both ɛe and μe exhibit a Lorentz-type anomalous dispersion, leading to a region where ɛe and μe are simultaneously negative. Then, considering a practical case, in which the thickness of photonic crystal is finite, the band structures for odd modes are calculated by the plane wave expansion method and the finite-difference time-domain method. The results suggest that reducing the external magnetic field strength or slab thickness will weaken the periodic modulation strength of the photonic crystal. Simulation results prove that the negative-index can be tuned by varying the external magnetic field strength or the slab thickness. The work presented in this paper gives a guideline for realizing the flat photonic crystal lens with tunable properties at optical frequencies, which may have potential applications in tunable near-field imaging systems. Project supported by the National Basic Research Program of China (Grant No. 2015CB352001), the Shanghai Rising-Star Program, China (Grant No. 12QA1402300), the China Scholarship Council (CSC) Program, and the Basic Research Program of Shanghai, China (Grant No. 14ZR1428500).

  19. Thermally tunable ferroelectric thin film photonic crystals.

    SciTech Connect

    Lin, P. T.; Wessels, B. W.; Imre, A.; Ocola, L. E.; Northwestern Univ.

    2008-01-01

    Thermally tunable PhCs are fabricated from ferroelectric thin films. Photonic band structure and temperature dependent diffraction are calculated by FDTD. 50% intensity modulation is demonstrated experimentally. This device has potential in active ultra-compact optical circuits.

  20. Photonic crystals composed of virtual pillars with magnetic walls: Photonic band gaps and double Dirac cones

    NASA Astrophysics Data System (ADS)

    Kim, Seong-Han; Kim, Soeun; Kee, Chul-Sik

    2016-08-01

    Photonic crystals composed of virtual pillars with magnetic walls are proposed. A virtual pillar with a magnetic wall can be created inside a parallel perfect electric conductor plate waveguide by introducing a circular perfect magnetic conductor patch in the upper perfect electric conductor plate of the waveguide. The virtual pillar mimics a perfect magnetic conductor pillar with a radius less than that of the circular patch because electromagnetic waves can slightly penetrate the wall. Furthermore, the photonic band structures of a triangular photonic crystal composed of virtual pillars for the transverse electromagnetic modes of the waveguide are investigated. They are very similar to those of a triangular photonic crystal composed of infinitely long perfect electric conductor cylinders for transverse magnetic modes. The similarity between the two different photonic crystals is well understood by the boundary conditions of perfect electric and magnetic conductor surfaces. A double Dirac cone at the center of the Brillouin zone is observed and thus the virtual pillar triangular photonic crystal can act a zero-refractive-index material at the Dirac point frequency.

  1. Switching Characteristics of Silica Nanoparticle-Doped Dual-Mode Liquid Crystal Device

    NASA Astrophysics Data System (ADS)

    Huang, Chi-Yen; Lai, Chien-Cheng; Huang, Yi-Jen; Chen, Jian-Hong

    2010-02-01

    We investigate the switching characteristics of a silica nanoparticle-doped dual-mode liquid crystal (LC) display. In the multistable mode, aggregated silica networks impede the relaxation of LCs and increase the response time of the cell. A low-frequency AC pulse voltage rotates LCs and breaks aggregated silica networks. The breaking of silica networks accelerates the relaxation of LCs and hence decreases the response time of the cell. The low-frequency AC pulse voltage gives the cell a fast response time of ˜23 ms, which is ˜4% of our previous result.

  2. Photonic-crystal-based all-optical NOT logic gate.

    PubMed

    Singh, Brahm Raj; Rawal, Swati

    2015-12-01

    In the present paper, we have utilized the concept of photonic crystals for the implementation of an optical NOT gate inverter. The designed structure has a hexagonal arrangement of silicon rods in air substrate. The logic function is based on the phenomenon of the existence of the photonic bandgap and resulting guided modes in defect photonic crystal waveguides. We have plotted the transmission, extinction ratio, and tolerance analysis graphs for the structure, and it has been observed that the maximum output is obtained for a telecom wavelength of 1.554 μm. Dispersion curves are obtained using the plane wave expansion method, and the transmission is simulated using the finite element method. The proposed structure is applicable for photonic integrated circuits due to its simple structure and clear operating principle.

  3. Photonic bandgap single-mode optical fibre with ytterbium-doped silica glass core

    SciTech Connect

    Egorova, O N; Semenov, S L; Vel'miskin, V V; Dianov, Evgenii M; Salganskii, M Yu; Yashkov, M V; Gur'yanov, Aleksei N

    2011-01-24

    A photonic bandgap fibre with an ytterbium-doped silica glass core is fabricated and investigated. The possibility of implementing single-mode operation of such fibres in a wide spectral range at a large (above 20 {mu}m) mode field diameter makes them promising for fibre lasers and amplifiers. To ensure a high quality of the beam emerging from the fibre, particular attention is paid to increasing the optical homogeneity of the ytterbium-doped core glass. (optical fibres)

  4. Three-dimensional metal dielectric photonic crystal based on self-assembled gold nanoshells

    NASA Astrophysics Data System (ADS)

    Lee, Jin Hyoung; Park, Wounjhang

    2008-08-01

    Recently developed metal nanoshells are ideal building blocks for metal-dielectric photonic crystals operating in visible and near-infrared spectrum. We applied silica coating to screen the van der Waals force and also added a dispersant to increase the electrostatic repulsive force. We also stabilized the gold nanoshell sterically by using a surfactant. With the use of tetrasodium pyrophosphate as a dispersant and Tween as a surfactant, we successfully obtained highly stable colloidal solution of gold nanoshells and subsequently self-assembled them into highly ordered opal structures. We observed well-defined diffraction pattern in the fast Fourier Transform spectra and optical spectra that match well the theoretical photonic band structure.

  5. Tuning and Freezing Disorder in Photonic Crystals using Percolation Lithography.

    PubMed

    Burgess, Ian B; Abedzadeh, Navid; Kay, Theresa M; Shneidman, Anna V; Cranshaw, Derek J; Lončar, Marko; Aizenberg, Joanna

    2016-01-01

    Although common in biological systems, synthetic self-assembly routes to complex 3D photonic structures with tailored degrees of disorder remain elusive. Here we show how liquids can be used to finely control disorder in porous 3D photonic crystals, leading to complex and hierarchical geometries. In these optofluidic crystals, dynamically tunable disorder is superimposed onto the periodic optical structure through partial wetting or evaporation. In both cases, macroscopic symmetry breaking is driven by subtle sub-wavelength variations in the pore geometry. These variations direct site-selective infiltration of liquids through capillary interactions. Incorporating cross-linkable resins into our liquids, we developed methods to freeze in place the filling patterns at arbitrary degrees of partial wetting and intermediate stages of drying. These percolation lithography techniques produced permanent photonic structures with adjustable disorder. By coupling strong changes in optical properties to subtle differences in fluid behavior, optofluidic crystals may also prove useful in rapid analysis of liquids. PMID:26790372

  6. Parametric Simulations of Slanted 1D Photonic Crystal Sensors.

    PubMed

    Breuer-Weil, Aaron; Almasoud, Naif Nasser; Abbasi, Badaruddin; Yetisen, Ali K; Yun, Seok-Hyun; Butt, Haider

    2016-12-01

    Photonic crystals and band gap materials act as manipulators of light and have a plethora of applications. They are made up of stacks of alternating dielectric constants. This article shows the simulations of an inclined, one dimensional and tuneble photonic crystal, using numerical finite element methods. The photonic crystal was made up of silver nanoparticles embedded in a hydrogel matrix and it has the ability to change and recover its periodicity. A series of factors concerning the geometry of the lattice were tested in order to analyze the efficiency, performance and optimize the properties of the optical sensor. These factors range from the size of the nanoparticles and their density within the stacks, to observing the effect of diffraction angle in readouts. PMID:27000025

  7. Ultrahigh-Q modes in anisotropic 2D photonic crystal

    NASA Astrophysics Data System (ADS)

    Bouleghlimat, Oussama; Hocini, Abdesselam

    2014-10-01

    In this work, we design a two-dimensional photonic crystal cavity made with a substrate of an anisotropic material. We consider triangular lattice photonic crystal made from air holes in tellurium. The cavity itself is then created by three missing holes in the centre. Using the three-dimensional finite-difference time-domain simulation and optimization of the geometrical parameters and the symmetric displacement of the edge air holes on the quality factor, the cavity’s structural parameters yield an ultrahigh-Q mode cavity with quality factor Q = 2.95 × 1011 for a filling factor r/a = 0.45 and lateral displacement of 10 nm. This shows great enhancement compared with previous studies in which silicon material has been used. The designed structure can be helpful in a number of applications associated with photonic crystal cavities, including quantum information processing, filters, and nanoscale sensors.

  8. Optical modulator based on coupled photonic crystal cavities

    NASA Astrophysics Data System (ADS)

    Serafimovich, Pavel G.; Kazanskiy, Nikolay L.

    2016-07-01

    We propose and numerically investigate an optical signal modulator based on two-photonic crystal nanobeam cavities coupled through a waveguide. The suggested modulator shifts the resonant frequency over a scalable range. We design a compact optical modulator based on photonic crystal nanobeams cavities that exhibits high stability to manufacturing. Photonic crystal waveguide tuning in the low-intensity region of the resonant mode is demonstrated. The advantages of the suggested approach over the single-resonator optical modulator approaches include the possibilities to shift the modulator frequency over a scalable range that depends on switching energy level and to effectively electrically tune the device in the low-intensity region of the resonant mode.

  9. Mode conversion in a magnetic photonic crystal waveguide

    NASA Astrophysics Data System (ADS)

    Otmani, H.; Bouchemat, M.; Hocini, A.; Boumaza, T.

    2014-06-01

    In this work, we have reported a theoretical study of a magnetic photonic crystal waveguide (also called a magneto photonic crystal waveguide). This structure is formed by a triangular lattice of air holes in a bismuth iron garnet (BIG) film, grown on gallium gadolinium garnet substrates. Nonreciprocal TE-TM mode conversion is caused by the Faraday rotation if the magnetization is aligned along the z-axis, parallel to mode of propagation. The properties of this phenomenon are simulated using the beam propagation method. The conversion output has been simulated, and the Faraday rotation and modal birefringence have been calculated by varying the gyrotropy and the thickness of the BIG film. This magnetic photonic crystal waveguide has the advantage of enhancing Faraday rotation in optical isolators.

  10. Tuning and Freezing Disorder in Photonic Crystals using Percolation Lithography

    NASA Astrophysics Data System (ADS)

    Burgess, Ian B.; Abedzadeh, Navid; Kay, Theresa M.; Shneidman, Anna V.; Cranshaw, Derek J.; Lončar, Marko; Aizenberg, Joanna

    2016-01-01

    Although common in biological systems, synthetic self-assembly routes to complex 3D photonic structures with tailored degrees of disorder remain elusive. Here we show how liquids can be used to finely control disorder in porous 3D photonic crystals, leading to complex and hierarchical geometries. In these optofluidic crystals, dynamically tunable disorder is superimposed onto the periodic optical structure through partial wetting or evaporation. In both cases, macroscopic symmetry breaking is driven by subtle sub-wavelength variations in the pore geometry. These variations direct site-selective infiltration of liquids through capillary interactions. Incorporating cross-linkable resins into our liquids, we developed methods to freeze in place the filling patterns at arbitrary degrees of partial wetting and intermediate stages of drying. These percolation lithography techniques produced permanent photonic structures with adjustable disorder. By coupling strong changes in optical properties to subtle differences in fluid behavior, optofluidic crystals may also prove useful in rapid analysis of liquids.

  11. Excitation enhancement and extraction enhancement with photonic crystals

    SciTech Connect

    Shapira, Ofer; Soljacic, Marin; Zhen, Bo; Chua, Song-Liang; Lee, Jeongwon; Joannopoulos, John

    2015-03-03

    Disclosed herein is a system for stimulating emission from at least one an emitter, such as a quantum dot or organic molecule, on the surface of a photonic crystal comprising a patterned dielectric substrate. Embodiments of this system include a laser or other source that illuminates the emitter and the photonic crystal, which is characterized by an energy band structure exhibiting a Fano resonance, from a first angle so as to stimulate the emission from the emitter at a second angle. The coupling between the photonic crystal and the emitter may result in spectral and angular enhancement of the emission through excitation and extraction enhancement. These enhancement mechanisms also reduce the emitter's lasing threshold. For instance, these enhancement mechanisms enable lasing of a 100 nm thick layer of diluted organic molecules solution with reduced threshold intensity. This reduction in lasing threshold enables more efficient organic light emitting devices and more sensitive molecular sensing.

  12. Tuning and Freezing Disorder in Photonic Crystals using Percolation Lithography

    PubMed Central

    Burgess, Ian B.; Abedzadeh, Navid; Kay, Theresa M.; Shneidman, Anna V.; Cranshaw, Derek J.; Lončar, Marko; Aizenberg, Joanna

    2016-01-01

    Although common in biological systems, synthetic self-assembly routes to complex 3D photonic structures with tailored degrees of disorder remain elusive. Here we show how liquids can be used to finely control disorder in porous 3D photonic crystals, leading to complex and hierarchical geometries. In these optofluidic crystals, dynamically tunable disorder is superimposed onto the periodic optical structure through partial wetting or evaporation. In both cases, macroscopic symmetry breaking is driven by subtle sub-wavelength variations in the pore geometry. These variations direct site-selective infiltration of liquids through capillary interactions. Incorporating cross-linkable resins into our liquids, we developed methods to freeze in place the filling patterns at arbitrary degrees of partial wetting and intermediate stages of drying. These percolation lithography techniques produced permanent photonic structures with adjustable disorder. By coupling strong changes in optical properties to subtle differences in fluid behavior, optofluidic crystals may also prove useful in rapid analysis of liquids. PMID:26790372

  13. Playing with light in diatoms: small water organisms with a natural photonic crystal structure

    NASA Astrophysics Data System (ADS)

    De Stefano, Luca; De Stefano, Mario; Maddalena, Pasqualino; Moretti, Luigi; Rea, Ilaria; Mocella, Vito; Rendina, Ivo

    2007-05-01

    Complex micro- and nano-structured materials for photonic applications are designed and fabricated using top technologies. A completely different approach to engineering systems at the sub-micron-scale consists in recognizing the nanostructures and morphologies that nature has optimized during life's history on earth. In fact, biological organisms could exhibit ordered geometries and complex photonic structures which often overcome the products of the best available fabrication technologies. An example is given by diatoms. They are microalgae with a peculiar cell wall made of amorphous hydrated silica valves, reciprocally interconnected in a structure called the frustule. Valve surfaces exhibit specie-specific patterns of regular arrays of chambers, called areolae, developed into the frustule depth. Areolae range in diameter from few hundreds of nanometers up to few microns, and can be circular, polygonal or elongate. The formation of these patterns can be modeled by self-organised phase separation. Despite of the high level of knowledge on the genesis and morphology of diatom frustules, their functions are not completely understood. In this work, we show that the silica skeletons of marine diatoms, characterized by a photonic crystal-like structure, have surprising optical properties, being capable of filtering and focalizing light, as well as exhibiting optical sensing capabilities.

  14. Ion crystal transducer for strong coupling between single ions and single photons.

    PubMed

    Lamata, L; Leibrandt, D R; Chuang, I L; Cirac, J I; Lukin, M D; Vuletić, V; Yelin, S F

    2011-07-15

    A new approach for the realization of a quantum interface between single photons and single ions in an ion crystal is proposed and analyzed. In our approach the coupling between a single photon and a single ion is enhanced via the collective degrees of freedom of the ion crystal. Applications including single-photon generation, a memory for a quantum repeater, and a deterministic photon-photon, photon-phonon, or photon-ion entangler are discussed.

  15. Confinement effects on Brillouin scattering in semiconductor nanowire photonic crystal

    NASA Astrophysics Data System (ADS)

    Mante, Pierre-Adrien; Anttu, Nicklas; Zhang, Wei; Wallentin, Jesper; Chen, I.-Ju; Lehmann, Sebastian; Heurlin, Magnus; Borgström, Magnus T.; Pistol, Mats-Erik; Yartsev, Arkady

    2016-07-01

    Scattering of photons by phonons, or Brillouin scattering, enables manipulation and control of light and has led to revolutionary applications, from slow light to saser and cooling of micromechanical resonators. Recently, enhanced light and sound interaction has been demonstrated in waveguides. However, the design of the waveguide geometry tunes and alters the phonon and photon dispersion simultaneously. Here we investigate, through femtosecond pump-probe spectroscopy and theoretical modeling, the light and sound interaction in a bottom-up fabricated vertical nanowire photonic crystal. In such a system, the phonon dispersion can be tuned by varying the geometry of the constituent nanowires. In contrast, the placement of the nanowires in the photonic crystal can be used for tuning optical array modes, without altering the phonon dispersion. We demonstrate the forward and backward scattering, by acoustic phonons in the nanowires, of (1) such optical array modes and (2) guided modes of the constituent nanowires. Furthermore, our results reveal an enhanced interaction of array modes with phonons that we attribute to the specific scattering mechanism. Our results enable the design of a photonic crystal with separately tailored photon and phonon dispersion for Brillouin scattering. We anticipate these advances to be a starting point for enhanced control of light at the nanoscale.

  16. Direct fiber-coupled single photon source based on a photonic crystal waveguide

    SciTech Connect

    Ahn, Byeong-Hyeon Lee, Chang-Min; Lim, Hee-Jin; Schlereth, Thomas W.; Kamp, Martin; Höfling, Sven; Lee, Yong-Hee

    2015-08-24

    A single photon source plays a key role in quantum applications such as quantum computers and quantum communications. Epitaxially grown quantum dots are one of the promising platforms to implement a good single photon source. However, it is challenging to realize an efficient single photon source based on semiconductor materials due to their high refractive index. Here we demonstrate a direct fiber coupled single photon source with high collection efficiency by employing a photonic crystal (PhC) waveguide and a tapered micro-fiber. To confirm the single photon nature, the second-order correlation function g{sup (2)}(τ) is measured with a Hanbury Brown-Twiss setup. The measured g{sup (2)}(0) value is 0.15, and we can estimate 24% direct collection efficiency from a quantum dot to the fiber.

  17. Photonic-crystal diplexers for terahertz-wave applications.

    PubMed

    Yata, Masahiro; Fujita, Masayuki; Nagatsuma, Tadao

    2016-04-01

    A compact diplexer is designed using a silicon photonic-crystal directional coupler of length comparable to the incident wavelength. The diplexer theoretically and experimentally exhibits a cross state bandwidth as broad as 2% of the operation frequency, with over 40-dB isolation between the cross and bar ports. We also demonstrate 1.5-Gbit/s frequency-division communication in the 0.32- and 0.33-THz bands using a single-wavelength-sized diplexer, and discuss the transmission bandwidth. Our study demonstrates the potential for application of photonic crystals as terahertz-wave integration platforms.

  18. Absorption and emission properties of photonic crystals and metamaterials

    SciTech Connect

    Peng, Lili

    2007-01-01

    We study the emission and absorption properties of photonic crystals and metamaterials using Comsol Multiphysics and Ansoft HFSS as simulation tools. We calculate the emission properties of metallic designs using drude model and the results illustrate that an appropriate termination of the surface of the metallic structure can significantly increase the absorption and therefore the thermal emissivity. We investigate the spontaneous emission rate modifications that occur for emitters inside two-dimensional photonic crystals and find the isotropic and directional emissions with respect to different frequencies as we have expected.

  19. Polarized quantum dot emission in electrohydrodynamic jet printed photonic crystals

    SciTech Connect

    See, Gloria G.; Xu, Lu; Nuzzo, Ralph G.; Sutanto, Erick; Alleyne, Andrew G.; Cunningham, Brian T.

    2015-08-03

    Tailored optical output, such as color purity and efficient optical intensity, are critical considerations for displays, particularly in mobile applications. To this end, we demonstrate a replica molded photonic crystal structure with embedded quantum dots. Electrohydrodynamic jet printing is used to control the position of the quantum dots within the device structure. This results in significantly less waste of the quantum dot material than application through drop-casting or spin coating. In addition, the targeted placement of the quantum dots minimizes any emission outside of the resonant enhancement field, which enables an 8× output enhancement and highly polarized emission from the photonic crystal structure.

  20. Optical filters using Cantor quasi-periodic one dimensional photonic crystal based on Si/SiO2

    NASA Astrophysics Data System (ADS)

    Sahel, S.; Amri, R.; Bouaziz, L.; Gamra, D.; Lejeune, M.; Benlahsen, M.; Zellama, K.; Bouchriha, H.

    2016-09-01

    Quasi-periodic one-dimensional Cantor photonic crystals are elaborated by depositing alternating silicon and silica Si/SiO2 layers by radiofrequency magnetron sputtering technique with cold plasma. Transmittance and reflectance spectra of these quasi crystals exhibit a large photonic band gap in the infrared range at normal incidence which is well reproduced by a theoretical model based on the transfer matrix method. The obtained wide photonic band gap reveals the existence of permitted modes depending on the nature and characteristics of the built in system which can constitute optical windows. This effect can be a good alternative for the design of flexible filters used in many areas of applications such as telecommunication and optoelectronic devices.

  1. Fabrication of high fidelity, high index three-dimensional photonic crystals using a templating approach

    NASA Astrophysics Data System (ADS)

    Xu, Yongan

    , a highly thermal and mechanical stable template is desired for PC fabrication. We fabricate the 3D POSS structures by MBIL, which can be converted to crack-free silica-like templates over the entire sample area (˜5 mm in diameter) by either thermal treatment in Ar at 500°C or O2 plasma, and the porosity can be conveniently controlled by O2 plasma power and time. Since POSS derivatives are soluble in HF aqueous solutions, we successfully replicate the 3D porous structures into polymers, such as PGMA and poly(dimethyl siloxane) (PDMS). We note that all the fabrication processes are conducted at room temperature, including template fabrication, infiltration and removal. Further, using 3D POSS structures as templates, here, we demonstrate the synthesis of 3D photonic crystals from silicon carbide and boron carbide, respectively, which are thermally stable above 1100°C in Ar. These non-oxide ceramic photonic crystals are potentially useful as ultrahigh temperature thermal barrier coatings that provide thermal protection for metallic components.

  2. Improving image quality and stability of two-dimensional photonic crystal slab by changing surface structure of the photonic crystal

    NASA Astrophysics Data System (ADS)

    Zhu, Zhao-Jie; Liu, Peng-Fang; Tong, Yuan-Wei

    2016-03-01

    The propagation of electromagnetic (EM) waves in two-dimensional hexagon-lattice photonic crystals (PCs) is investigated through dispersion characteristics analysis and numerical simulation of field pattern. The full width at half maximum (FWHM) of the image reach 0.37λ which is much smaller than 0.5λ by changing surface structure of the photonic crystal, and the variance of FWHM of image focused by the changed slab seems to be less than the variance of FWHM of image focused by the original slab with the changing of source position.

  3. Dual concentric crystal low energy photon detector

    DOEpatents

    Guilmette, R.A.

    A photon detector for biological samples includes a block of NaI(T1) having a hole containing a thin walled cylinder of CsI(T1). At least three photo multiplier tubes are evenly spaced around the parameter of the block. Biological samples are placed within the hole, and emissions which are sensed by at least two of the photo multipliers from only the NaI(T1) detector are counted.

  4. Silicon photonic crystal thermal emitter at near-infrared wavelengths

    PubMed Central

    O’Regan, Bryan J.; Wang, Yue; Krauss, Thomas F.

    2015-01-01

    Controlling thermal emission with resonant photonic nanostructures has recently attracted much attention. Most of the work has concentrated on the mid-infrared wavelength range and/or was based on metallic nanostructures. Here, we demonstrate the experimental operation of a resonant thermal emitter operating in the near-infrared (≈1.5 μm) wavelength range. The emitter is based on a doped silicon photonic crystal consisting of a two dimensional square array of holes and using silicon-on-insulator technology with a device-layer thickness of 220 nm. The device is resistively heated by passing current through the photonic crystal membrane. At a temperature of ≈1100 K, we observe relatively sharp emission peaks with a Q factor around 18. A support structure system is implemented in order to achieve a large area suspended photonic crystal thermal emitter and electrical injection. The device demonstrates that weak absorption together with photonic resonances can be used as a wavelength-selection mechanism for thermal emitters, both for the enhancement and the suppression of emission. PMID:26293111

  5. Silicon photonic crystal thermal emitter at near-infrared wavelengths.

    PubMed

    O'Regan, Bryan J; Wang, Yue; Krauss, Thomas F

    2015-08-21

    Controlling thermal emission with resonant photonic nanostructures has recently attracted much attention. Most of the work has concentrated on the mid-infrared wavelength range and/or was based on metallic nanostructures. Here, we demonstrate the experimental operation of a resonant thermal emitter operating in the near-infrared (≈1.5 μm) wavelength range. The emitter is based on a doped silicon photonic crystal consisting of a two dimensional square array of holes and using silicon-on-insulator technology with a device-layer thickness of 220 nm. The device is resistively heated by passing current through the photonic crystal membrane. At a temperature of ≈1100 K, we observe relatively sharp emission peaks with a Q factor around 18. A support structure system is implemented in order to achieve a large area suspended photonic crystal thermal emitter and electrical injection. The device demonstrates that weak absorption together with photonic resonances can be used as a wavelength-selection mechanism for thermal emitters, both for the enhancement and the suppression of emission.

  6. Multicolor fluorescence enhancement from a photonics crystal surface

    NASA Astrophysics Data System (ADS)

    Pokhriyal, A.; Lu, M.; Huang, C. S.; Schulz, S.; Cunningham, B. T.

    2010-09-01

    A photonic crystal substrate exhibiting resonant enhancement of multiple fluorophores has been demonstrated. The device, fabricated uniformly from plastic materials over a ˜3×5 in.2 surface area by nanoreplica molding, utilizes two distinct resonant modes to enhance electric field stimulation of a dye excited by a λ =632.8 nm laser (cyanine-5) and a dye excited by a λ =532 nm laser (cyanine-3). Resonant coupling of the laser excitation to the photonic crystal surface is obtained for each wavelength at a distinct incident angle. Compared to detection of a dye-labeled protein on an ordinary glass surface, the photonic crystal surface exhibited a 32× increase in fluorescent signal intensity for cyanine-5 conjugated streptavidin labeling, while a 25× increase was obtained for cyanine-3 conjugated streptavidin labeling. The photonic crystal is capable of amplifying the output of any fluorescent dye with an excitation wavelength in the 532 nm<λ<633 nm range by selection of an appropriate incident angle. The device is designed for biological assays that utilize multiple fluorescent dyes within a single imaged area, such as gene expression microarrays.

  7. Multicolor fluorescence enhancement from a photonics crystal surface

    PubMed Central

    Pokhriyal, A.; Lu, M.; Huang, C. S.; Schulz, S.; Cunningham, B. T.

    2010-01-01

    A photonic crystal substrate exhibiting resonant enhancement of multiple fluorophores has been demonstrated. The device, fabricated uniformly from plastic materials over a ∼3×5 in.2 surface area by nanoreplica molding, utilizes two distinct resonant modes to enhance electric field stimulation of a dye excited by a λ=632.8 nm laser (cyanine-5) and a dye excited by a λ=532 nm laser (cyanine-3). Resonant coupling of the laser excitation to the photonic crystal surface is obtained for each wavelength at a distinct incident angle. Compared to detection of a dye-labeled protein on an ordinary glass surface, the photonic crystal surface exhibited a 32× increase in fluorescent signal intensity for cyanine-5 conjugated streptavidin labeling, while a 25× increase was obtained for cyanine-3 conjugated streptavidin labeling. The photonic crystal is capable of amplifying the output of any fluorescent dye with an excitation wavelength in the 532 nm<λ<633 nm range by selection of an appropriate incident angle. The device is designed for biological assays that utilize multiple fluorescent dyes within a single imaged area, such as gene expression microarrays. PMID:20957067

  8. Ultraflat supercontinuum generation in soft-glass photonic crystal fibers

    NASA Astrophysics Data System (ADS)

    Miret, J. J.; Silvestre, E.; Andrés, P.

    2009-05-01

    We recognize some photonic-crystal-fiber structures, made up of soft glass, that generate ultrawide (over an octave), very smooth and highly coherent supercontinuum spectrum when illuminated with femtosecond pulsed light around 1.55 μm. The design of soft-glass microstructured fiber geometry with nearly ultraflattened, positive and low dispersion is crucial to accomplish the above goals.

  9. [INVITED] New perspectives in photonic crystal fibre sensors

    NASA Astrophysics Data System (ADS)

    Villatoro, Joel; Zubia, Joseba

    2016-04-01

    In this paper we analyse the recent advances on sensors based on photonic crystal fibres(PCFs) and discuss their advantages and disadvantages. Some innovative approaches to overcome the main limitations of PCF sensors are also analysed. In addition, we discuss some opportunities and challenges in PCF sensing for the coming years.

  10. Soft-glass hollow-core photonic crystal fibers

    NASA Astrophysics Data System (ADS)

    Melnikov, Leonid; Khromova, Irina; Scherbakov, Andrey; Nikishin, Nikolay

    2005-09-01

    The results of numerical modeling and experimental investigations of manufactured diamond-shaped and large area hollow core photonic crystal fibers with periodical cladding (kagome-lattice and closely packed tubes) are presented. The use of soft glasses allows to fabricate high-quality structures with moderate losses. Numerical methods, designing strategies and fabrication issues of these promising fiber structures are discussed.

  11. Solar power conversion efficiency in modulated silicon nanowire photonic crystals

    NASA Astrophysics Data System (ADS)

    Deinega, Alexei; John, Sajeev

    2012-10-01

    It is suggested that using only 1 μm of silicon, sculpted in the form of a modulated nanowire photonic crystal, solar power conversion efficiency in the range of 15%-20% can be achieved. Choosing a specific modulation profile provides antireflection, light trapping, and back-reflection over broad angles in targeted spectral regions for high efficiency power conversion without solar tracking. Solving both Maxwell's equations in the 3D photonic crystal and the semiconductor drift-diffusion equations in each nanowire, we identify optimal junction and contact geometries and study the influence of the nanowire surface curvature on solar cell efficiency. We demonstrate that suitably modulated nanowires enable 20% efficiency improvement over their straight counterparts made of an equivalent amount of silicon. We also discuss the efficiency of a tandem amorphous and crystalline silicon nanowire photonic crystal solar cell. Opportunities for "hot carrier" collection and up-conversion of infrared light, enhanced by photonic crystal geometry, facilitate further improvements in power efficiency.

  12. Light trapping in thin film solar cells using textured photonic crystal

    DOEpatents

    Yi, Yasha; Kimerling, Lionel C.; Duan, Xiaoman; Zeng, Lirong

    2009-01-27

    A solar cell includes a photoactive region that receives light. A photonic crystal is coupled to the photoactive region, wherein the photonic crystal comprises a distributed Bragg reflector (DBR) for trapping the light.

  13. Fabrication of colloidal photonic crystal heterostructures free of interface imperfection based on solvent vapor annealing.

    PubMed

    Liu, Xiaomiao; Zhao, Duobiao; Geng, Chong; Zhang, Lijing; Tan, Tianya; Hu, Mingzhe; Yan, Qingfeng

    2014-11-15

    We describe the transformation of a colloidal photonic crystal into a photonic crystal heterostructure. It was achieved by annealing a polystyrene multilayer colloidal photonic crystal partially immersed in water using a solvent vapor. The floating polystyrene colloidal photonic crystal was divided into two parts by the liquid level, which can be manipulated by the addition of ethanol into the water. The top part protruding out of the water experienced a uniform lattice stretching upon exposure to the solvent vapor. The bottom part that stayed immersed in the water remained unaffected due to the protection by the water. The inconsistent behaviors of the two parts resulted in the formation of a colloidal photonic crystal heterostructure. Such a heterostructure was free of interface imperfection since it was a direct descendant of the original colloidal crystal. Meanwhile, optical measurements demonstrated the presence of a wider photonic band gap along the crystallographic [111] direction in these photonic crystal heterostructures compared with the original colloidal photonic crystals.

  14. Photonic crystal surface-emitting lasers enabled by an accidental Dirac point

    SciTech Connect

    Chua, Song Liang; Lu, Ling; Soljacic, Marin

    2014-12-02

    A photonic-crystal surface-emitting laser (PCSEL) includes a gain medium electromagnetically coupled to a photonic crystal whose energy band structure exhibits a Dirac cone of linear dispersion at the center of the photonic crystal's Brillouin zone. This Dirac cone's vertex is called a Dirac point; because it is at the Brillouin zone center, it is called an accidental Dirac point. Tuning the photonic crystal's band structure (e.g., by changing the photonic crystal's dimensions or refractive index) to exhibit an accidental Dirac point increases the photonic crystal's mode spacing by orders of magnitudes and reduces or eliminates the photonic crystal's distributed in-plane feedback. Thus, the photonic crystal can act as a resonator that supports single-mode output from the PCSEL over a larger area than is possible with conventional PCSELs, which have quadratic band edge dispersion. Because output power generally scales with output area, this increase in output area results in higher possible output powers.

  15. Enhanced trion emission from colloidal quantum dots with photonic crystals by two-photon excitation

    NASA Astrophysics Data System (ADS)

    Xu, Xingsheng

    2013-11-01

    For colloidal quantum dots, the ongoing biggest problem is their fluorescence blinking. Until now, there is no generally accepted model for this fluorescence blinking. Here, two-photon excited fluorescence from CdSe/ZnS nanocrystals on silicon nitride photonic crystals is studied using a femtosecond laser. From analysis of the spectra and decay processes, most of the relative trion efficiency is larger than 10%, and the largest relative trion efficiency reaches 46.7%. The photonic crystals enhance the trion emission of CdSe/ZnS nanocrystals, where the enhancement is due to the coupling of the trion emission to the leaky mode of the photonic crystal slab. Moreover, the photonic crystals enhance the Auger-assisted trapping efficiency of electrons/holes to surface states, and then enhance the efficiency of the generations of charge separation and DC electric field, which modifies the trion spectrum. Therefore, a model is present for explaining the mechanism of fluorescence blinking including the effect of the environment.

  16. Modified thermal radiation in three-dimensional photonic crystals

    NASA Astrophysics Data System (ADS)

    Li, Zhi-Yuan

    2002-12-01

    Thermal radiation from an empty blackbody cavity follows the conventional Wien’s displacement law. At a temperature T=2500 K, the maximum monochromatic radiation intensity lies at a wavelength of 1.16 μm, and radiation into the visible band occupies only 3% of the total radiation energy. In this paper, we show that when the cavity is filled with a three-dimensional photonic crystal, a strong thermal radiation band can appear in the visible regime, significantly improving the luminescence efficiency. This is attributed to the redistribution of photon density of states (DOS) in different frequency ranges in the photonic crystal leading to orders-of-magnitude enhancement of DOS in the visible wavelength over that in the infrared wavelengths.

  17. Thermal properties photonic crystal fiber transducers with ferromagnetic nanoparticles

    NASA Astrophysics Data System (ADS)

    Przybysz, N.; Marć, P.; Kisielewska, A.; Jaroszewicz, L. R.

    2015-12-01

    The main aim of the research is to design new types of fiber optic transducers based on filled photonic crystal fibers for sensor applications. In our research we propose to use as a filling material nanoparticles' ferrofluids (Fe3O4 NPs). Optical properties of such transducers are studied by measurements of spectral characteristics' changes when transducers are exposed to temperature and magnetic field changes. From synthesized ferrofluid several mixtures with different NPs' concentrations were prepared. Partially filled commercially available photonic crystal fiber LMA 10 (NKT Photonics) was used to design PCF transducers. Their thermo-optic properties were tested in a temperature chamber. Taking into account magnetic properties of synthetized NPs the patch cords based on a partially filled PM 1550 PCF were measured.

  18. Nano-photonic organic solar cell architecture for advanced light management utilizing dual photonic crystals

    NASA Astrophysics Data System (ADS)

    Peer, Akshit; Biswas, Rana

    2015-09-01

    Organic solar cells have rapidly increasing efficiencies, but typically absorb less than half of the incident solar spectrum. To increase broadband light absorption, we rigorously design experimentally realizable solar cell architectures based on dual photonic crystals. Our optimized architecture consists of a polymer microlens at the air-glass interface, coupled with a photonic-plasmonic crystal at the metal cathode. The microlens focuses light on the periodic nanostructure that generates strong light diffraction. Waveguiding modes and surface plasmon modes together enhance long wavelength absorption in P3HT-PCBM. The architecture has a period of 500 nm, with absorption and photocurrent enhancement of 49% and 58%, respectively.

  19. Nanocrystalline diamond photonics platform with high quality factor photonic crystal cavities

    NASA Astrophysics Data System (ADS)

    Checoury, X.; Néel, D.; Boucaud, P.; Gesset, C.; Girard, H.; Saada, S.; Bergonzo, P.

    2012-10-01

    We demonstrate a diamond photonics platform with integrated suspended waveguide-cavity structures and two dimensional photonic crystal (PhC) cavities. PhC cavities with quality factors exceeding 2800 have been fabricated using a top-down approach from thin nanocrystalline diamond films. The developed technological process allows one to access these cavities in a fully planar geometry, including light injection and collection from the outside using lensed-fibers. This diamond platform opens the road to large scale fabrication of photonics devices including optical sensor chips.

  20. Assembly of optical-scale dumbbells into dense photonic crystals.

    PubMed

    Forster, Jason D; Park, Jin-Gyu; Mittal, Manish; Noh, Heeso; Schreck, Carl F; O'Hern, Corey S; Cao, Hui; Furst, Eric M; Dufresne, Eric R

    2011-08-23

    We describe the self-assembly of nonspherical particles into crystals with novel structure and optical properties combining a partial photonic band gap with birefringence that can be modulated by an external field or quenched by solvent evaporation. Specifically, we study symmetric optical-scale polymer dumbbells with an aspect ratio of 1.58. Hard particles with this geometry have been predicted to crystallize in equilibrium at high concentrations. However, unlike spherical particles, which readily crystallize in the bulk, previous experiments have shown that these dumbbells crystallize only under strong confinement. Here, we demonstrate the use of an external electric field to align and assemble the dumbbells to make a birefringent suspension with structural color. When the electric field is turned off, the dumbbells rapidly lose their orientational order and the color and birefringence quickly go away. In this way, dumbbells combine the structural color of photonic crystals with the field addressability of liquid crystals. In addition, we find that if the solvent is removed in the presence of an electric field, the particles self-assemble into a novel, dense crystalline packing hundreds of particles thick. Analysis of the crystal structure indicates that the dumbbells have a packing fraction of 0.7862, higher than the densest known packings of spheres and ellipsoids. We perform numerical experiments to more generally demonstrate the importance of controlling the orientation of anisotropic particles during a concentration quench to achieve long-range order.

  1. Invited Review Article: Development of crystal lenses for energetic photons

    SciTech Connect

    Smither, Robert K.

    2014-08-15

    This paper follows the development of crystal diffraction lenses designed to focus energetic photons. It begins with the search for a solution to the astrophysics problem of how to detect weak astrophysics sources of gamma rays and x-rays. This led to the basic designs for a lens and to the understanding of basic limitations of lens design. The discussion of the development of crystal diffraction lenses is divided into two parts: lenses using crystals with mosaic structure, and lenses that use crystals with curved crystal planes. This second group divides into two sub-groups: (1) Curved crystals that are used to increase the acceptance angle of the diffraction of a monochromatic beam and to increase the energy bandwidth of the diffraction. (2) Curved crystals used to focus gamma ray beams. The paper describes how these two types of crystals affect the design of the corresponding crystal lenses in different fields: astrophysics, medical imaging, detection of weak, distant, gamma-ray sources, etc. The designs of crystal lenses for these applications are given in enough detail to allow the reader to design a lens for his own application.

  2. Plasmonic photonic crystals realized through DNA-programmable assembly

    PubMed Central

    Park, Daniel J.; Zhang, Chuan; Ku, Jessie C.; Zhou, Yu; Schatz, George C.; Mirkin, Chad A.

    2015-01-01

    Three-dimensional dielectric photonic crystals have well-established enhanced light–matter interactions via high Q factors. Their plasmonic counterparts based on arrays of nanoparticles, however, have not been experimentally well explored owing to a lack of available synthetic routes for preparing them. However, such structures should facilitate these interactions based on the small mode volumes associated with plasmonic polarization. Herein we report strong light-plasmon interactions within 3D plasmonic photonic crystals that have lattice constants and nanoparticle diameters that can be independently controlled in the deep subwavelength size regime by using a DNA-programmable assembly technique. The strong coupling within such crystals is probed with backscattering spectra, and the mode splitting (0.10 and 0.24 eV) is defined based on dispersion diagrams. Numerical simulations predict that the crystal photonic modes (Fabry–Perot modes) can be enhanced by coating the crystals with a silver layer, achieving moderate Q factors (∼102) over the visible and near-infrared spectrum. PMID:25548175

  3. Model calculations for enhanced fluorescence in photonic crystal phosphor.

    PubMed

    Min, Kyungtaek; Choi, Yun-Kyoung; Jeon, Heonsu

    2012-01-30

    We propose a novel photonic structure, based on the photonic crystal (PC) effect, which simulations show results in an improved fluorescence efficiency from embedded phosphor. To be specific, the phosphor pumping efficiency can be significantly improved by tuning the pump photon energy to a photonic band-edge (PBE) of the PC phosphor. We have confirmed this theoretically by calculating optical properties of one-dimensional PC phosphor structures using the transfer-matrix method and plane-wave expansion method. For a particular model structure based on a quantum dot phosphor, the fluorescence enhancement factor was estimated to be as high as 6.9 for a monochromatic pump source and 2.2 for a broad bandwidth (20 nm) pump source.

  4. Density of photonic states in cholesteric liquid crystals

    NASA Astrophysics Data System (ADS)

    Dolganov, P. V.

    2015-04-01

    Density of photonic states ρ (ω ) , group vg, and phase vph velocity of light, and the dispersion relation between wave vector k , and frequency ω (k ) were determined in a cholesteric photonic crystal. A highly sensitive method (measurement of rotation of the plane of polarization of light) was used to determine ρ (ω ) in samples of different quality. In high-quality samples a drastic increase in ρ (ω ) near the boundaries of the stop band and oscillations related to Pendellösung beatings are observed. In low-quality samples photonic properties are strongly modified. The maximal value of ρ (ω ) is substantially smaller, and density of photonic states increases near the selective reflection band without oscillations in ρ (ω ) . Peculiarities of ρ (ω ) , vg, and ω (k ) are discussed. Comparison of the experimental results with theory was performed.

  5. Two-photon absorption spectroscopy of rubrene single crystals

    NASA Astrophysics Data System (ADS)

    Irkhin, Pavel; Biaggio, Ivan

    2014-05-01

    We determine the wavelength dependence of the two-photon absorption cross section in rubrene single crystals both by direct measurement of nonlinear transmission and from the two-photon excitation spectrum of the photoluminescence. The peak two-photon absorption coefficient for b-polarized light was found to be (4.6±1)×10-11 m/W at a wavelength of 850±10 nm. It is 2.3 times larger for c-polarized light. The lowest energy two-photon excitation peak corresponds to an excited state energy of 2.92±0.04 eV and it is followed by a vibronic progression of higher energy peaks separated by ˜0.14 eV.

  6. Recent Progresses and Future Prospects of Two- and Three-Dimensional Photonic Crystals

    NASA Astrophysics Data System (ADS)

    Noda, Susumu

    2006-12-01

    Photonic crystals, in which the refractive index changes periodically, provide an exciting new tool for the manipulation of photons and have received keen interest from a variety of fields. This paper reviews the recent progress and future prospects of photonic crystals and their applications to photonic-nanostructure devices.

  7. Imaging and tuning of coupled photonic crystal cavities (Conference Presentation)

    NASA Astrophysics Data System (ADS)

    Gurioli, Massimo

    2016-04-01

    Photonic microcavities (PMC) coupled through their evanescent field are used for a large variety of classical and quantum devices. In such systems, a molecular-like spatial delocalization of the coupled modes is achieved by an evanescent tunnelling. The tunnelling rate depends on the height and depth of the photonic barrier between two adjacent resonators and therefore it is sensitive to the fabrication-induced disorder present in the center of the molecule. In this contribution, we address the problem of developing a post fabrication control of the tunnelling rate in photonic crystal coupled PMCs. The value of the photonic coupling (proportional to the tunnelling rate) is directly measured by the molecular mode splitting at the anticrossing point. By exploiting a combination of tuning techniques such as local infiltration of water, micro-evaporation, and laser induced non thermal micro-oxidation, we are able to either increase or decrease the detuning and the photonic coupling, independently. Near field imaging is also used for mapping the modes and establish delocalization. By water micro-infiltration, we were able to increase the photon coupling by 28%. On the contrary, by laser induced non thermal oxidation, we got a reduction of g by 30%. The combination of the two methods would therefore give a complete control of g with excellent accuracy. This could make possible the realization of array of photonic cavities with on demand tunnelling rate between each pair of coupled resonators. We believe that this peculiar engineering of photonic crystal molecules would open the road to possible progress in the exploitation of coherent interference between coupled optical resonators both for quantum information processing and optical communication.

  8. Water-dependent micromechanical and rheological properties of silica colloidal crystals studied by nanoindentation.

    PubMed

    Gallego-Gómez, Francisco; Morales-Flórez, Víctor; Blanco, Alvaro; de la Rosa-Fox, Nicolás; López, Cefe

    2012-09-12

    Here we show the suitability of nanoindentation to study in detail the micromechanical response of silica colloidal crystals (CCs). The sensitivity to displacements smaller than the submicrometer spheres size, even resolving discrete events and superficial features, revealed particulate features with analogies to atomic crystals. Significant robustness, long-range structural deformation, and large energy dissipation were found. Easily implemented temperature/rate-dependent nanoindentation quantified the paramount role of adsorbed water endowing silica CCs with properties of wet granular materials like viscoplasticity. A novel "nongranular" CC was fabricated by substituting capillary bridges with silica necks to directly test water-independent mechanical response. Silica CCs, as specific (nanometric, ordered) wet granular assemblies with well-defined configuration, may be useful model systems for granular science and capillary cohesion at the nanoscale.

  9. Novel photonic crystals: incorporation of nano-CdS into the natural photonic crystals within peacock feathers.

    PubMed

    Han, Jie; Su, Huilan; Song, Fang; Gu, Jiajun; Di, Zhang; Jiang, Limin

    2009-03-01

    In this investigation, the natural 2D photonic crystals (PhCs) within peacock feathers are applied to incorporate CdS nanocrystallites. Peacock feathers are activated by ethylenediaminetetraacetic/dimethylformamide suspension to increase the reactive sites on the keratin component, on which CdS nanoparticles (nano-CdS) are in situ formed in succession and serve as the "seeds" to direct further incorporation during the following solvothermal procedure. Thus, homogeneous nano-CdS are loaded both on the feathers' surface layer and inside the 2D PhCs. The obtained nano-CdS/peacock feathers hybrids are novel photonic crystals whose photonic stop bands are markedly different from that of the natural PhCs within original peacock feathers, as observed by the reflection spectra.

  10. Activation of snap-top capped mesoporous silica nanocontainers using two near-infrared photons.

    PubMed

    Guardado-Alvarez, Tania M; Sudha Devi, Lekshmi; Russell, Melissa M; Schwartz, Benjamin J; Zink, Jeffrey I

    2013-09-25

    Photoactivation of "snap-top" stoppers over the pore openings of mesoporous silica nanoparticles releases intact cargo molecules from the pores. The on-command release can be stimulated by either one UV photon or two coherent near-IR photons. Two-photon activation is particularly desirable for use in biological systems because it enables good tissue penetration and precise spatial control. Stoppers were assembled by first binding photolabile coumarin-based molecules to the nanoparticle surface. Then, after the particles were loaded with cargo, bulky β-cyclodextrin (CD) molecules were noncovalently associated with the substituted coumarin molecule, blocking the pores and preventing the cargo from escaping. One-photon excitation at 376 nm or two-photon excitation at 800 nm cleaves the bond holding the coumarin to the nanopore, releasing both the CD cap and the cargo. The dynamics of both the cleavage of the cap and the cargo release was monitored using fluorescence spectroscopy. This system traps intact cargo molecules without the necessity of chemical modification, releases them with tissue-penetrating near-IR light, and has possible applications in photostimulated drug delivery.

  11. Engineered atom-light interactions in 1D photonic crystals

    NASA Astrophysics Data System (ADS)

    Martin, Michael J.; Hung, Chen-Lung; Yu, Su-Peng; Goban, Akihisa; Muniz, Juan A.; Hood, Jonathan D.; Norte, Richard; McClung, Andrew C.; Meenehan, Sean M.; Cohen, Justin D.; Lee, Jae Hoon; Peng, Lucas; Painter, Oskar; Kimble, H. Jeff

    2014-05-01

    Nano- and microscale optical systems offer efficient and scalable quantum interfaces through enhanced atom-field coupling in both resonators and continuous waveguides. Beyond these conventional topologies, new opportunities emerge from the integration of ultracold atomic systems with nanoscale photonic crystals. One-dimensional photonic crystal waveguides can be engineered for both stable trapping configurations and strong atom-photon interactions, enabling novel cavity QED and quantum many-body systems, as well as distributed quantum networks. We present the experimental realization of such a nanophotonic quantum interface based on a nanoscale photonic crystal waveguide, demonstrating a fractional waveguide coupling of Γ1 D /Γ' of 0 . 32 +/- 0 . 08 , where Γ1 D (Γ') is the atomic emission rate into the guided (all other) mode(s). We also discuss progress towards intra-waveguide trapping of ultracold Cs. This work was supported by the IQIM, an NSF Physics Frontiers Center with support from the Moore Foundation, the DARPA ORCHID program, the AFOSR QuMPASS MURI, the DoD NSSEFF program, NSF, and the Kavli Nanoscience Institute (KNI) at Caltech.

  12. Nanospheres of silica with an epsilon-Fe2O3 single crystal nucleus.

    PubMed

    Taboada, Elena; Gich, Martí; Roig, Anna

    2009-11-24

    A route to produce single crystals of epsilon-Fe(2)O(3) individually wrapped in a silica shell is presented. Formation of epsilon-Fe(2)O(3)/silica nanospheres was achieved by controlled recrystallization of maghemite particles confined in silica shells via calcination in air. Phase transition was monitored by X-ray diffraction, magnetometry, and transmission electron microscopy. Core-shell nanocomposite particles can be dispersed as a colloidal suspension in several polar liquids enlarging the processability spectrum of the material and thus facilitating the use of epsilon-Fe(2)O(3) in technological applications and its integration in devices.

  13. Photonic-magnonic crystals: Multifunctional periodic structures for magnonic and photonic applications

    SciTech Connect

    Kłos, J. W. Krawczyk, M.; Dadoenkova, Yu. S.; Dadoenkova, N. N.; Lyubchanskii, I. L.

    2014-05-07

    We investigate the properties of a photonic-magnonic crystal, a complex multifunctional one-dimensional structure with magnonic and photonic band gaps in the GHz and PHz frequency ranges for spin waves and light, respectively. The system consists of periodically distributed dielectric magnetic slabs of yttrium iron garnet and nonmagnetic spacers with an internal structure of alternating TiO{sub 2} and SiO{sub 2} layers which form finite-size dielectric photonic crystals. We show that the spin-wave coupling between the magnetic layers, and thus the formation of the magnonic band structure, necessitates a nonzero in-plane component of the spin-wave wave vector. A more complex structure perceived by light is evidenced by the photonic miniband structure and the transmission spectra in which we have observed transmission peaks related to the repetition of the magnetic slabs in the frequency ranges corresponding to the photonic band gaps of the TiO{sub 2}/SiO{sub 2} stack. Moreover, we show that these modes split to very high sharp (a few THz wide) subpeaks in the transmittance spectra. The proposed novel multifunctional artificial crystals can have interesting applications and be used for creating common resonant cavities for spin waves and light to enhance the mutual influence between them.

  14. Photonic crystal fibers based on chalcogenide glasses

    NASA Astrophysics Data System (ADS)

    Adam, J. L.; Troles, J.; Brilland, L.; Coulombier, Q.; Chartier, T.

    2010-10-01

    Chalcogenide glasses are known for their large transparency in the mid-infrared and their high refractive index (>2). They present also a high non-linear coefficient (n2), 100 to 1000 times larger than for silica, depending on the composition. An original way to obtain single-mode fibers is to design microstructured optical fibers (MOFs). These fibers present unique optical properties thanks to the high degree of freedom in the design of their geometrical structure. A classical method to realize MOFs is the stack-and-draw technique. However, with chalcogenide glasses, that technique induces optical losses at the interfaces in the stack of capillaries. In consequence, we have developed a new casting method to fabricate the chalcogenide preform. This method permits to obtain optical losses around 1 dB/m at 1.55 μm and 0.3 dB/m in the mid-IR region. Various chalcogenide microstructured fibers working in the IR range were prepared in order to take advantage of the non-linear properties of these glasses and of the original MOF properties. For example, fibers with small effective mode area (Aeff < 10 μm2) have been realized to exacerbate the non-linear optical properties. Such fibers will find applications for signal regeneration in telecom, and for the generation of supercontinuum sources. On the contrary, for military applications in the 3-5 and 8-12 μm windows, large effective mode area and single mode fibers have been designed to permit the propagation of high-power gaussian laser beams.

  15. Photonic NOT and NOR gates based on a single compact photonic crystal ring resonator.

    PubMed

    Bai, Jibo; Wang, Junqin; Jiang, Junzhen; Chen, Xiyao; Li, Hui; Qiu, Yishen; Qiang, Zexuan

    2009-12-20

    New all-optical NOT and NOR logic gates based on a single ultracompact photonic crystal ring resonator (PCRR) have been proposed. The PCRR was formed by removing the line defect along the GammaM direction instead of the conventional GammaX direction in a square-pattern cylindrical silicon-rod photonic crystal structure. The behavior of the proposed logic gates is qualitatively analyzed with the theory of beam interference and then numerically investigated by use of the two-dimensional finite-difference time-domain method. No nonlinear material is required with less than a 2.2 microm effective ring radius. The wavelengths of the input signal and the probe signal are the same. This new device can potentially be used in on-chip photonic logic-integrated circuits. PMID:20029593

  16. Broadband single-photon-level memory in a hollow-core photonic crystal fibre

    NASA Astrophysics Data System (ADS)

    Sprague, M. R.; Michelberger, P. S.; Champion, T. F. M.; England, D. G.; Nunn, J.; Jin, X.-M.; Kolthammer, W. S.; Abdolvand, A.; Russell, P. St. J.; Walmsley, I. A.

    2014-04-01

    Storing information encoded in light is critical for realizing optical buffers for all-optical signal processing and quantum memories for quantum information processing. These proposals require efficient interaction between atoms and a well-defined optical mode. Photonic crystal fibres can enhance light-matter interactions and have engendered a broad range of nonlinear effects; however, the storage of light has proven elusive. Here, we report the first demonstration of an optical memory in a hollow-core photonic crystal fibre. We store gigahertz-bandwidth light in the hyperfine coherence of caesium atoms at room temperature using a far-detuned Raman interaction. We demonstrate a signal-to-noise ratio of 2.6:1 at the single-photon level and a memory efficiency of 27 +/- 1%. Our results demonstrate the potential of a room-temperature fibre-integrated optical memory for implementing local nodes of quantum information networks.

  17. Polarization Engineering in Photonic Crystal Waveguides for Spin-Photon Entanglers.

    PubMed

    Young, A B; Thijssen, A C T; Beggs, D M; Androvitsaneas, P; Kuipers, L; Rarity, J G; Hughes, S; Oulton, R

    2015-10-01

    By performing a full analysis of the projected local density of states (LDOS) in a photonic crystal waveguide, we show that phase plays a crucial role in the symmetry of the light-matter interaction. By considering a quantum dot (QD) spin coupled to a photonic crystal waveguide (PCW) mode, we demonstrate that the light-matter interaction can be asymmetric, leading to unidirectional emission and a deterministic entangled photon source. Further we show that understanding the phase associated with both the LDOS and the QD spin is essential for a range of devices that can be realized with a QD in a PCW. We also show how suppression of quantum interference prevents dipole induced reflection in the waveguide, and highlight a fundamental breakdown of the semiclassical dipole approximation for describing light-matter interactions in these spin dependent systems. PMID:26550722

  18. High Quality Factor Metallodielectric Hybrid Plasmonic-Photonic Crystals

    SciTech Connect

    Yu, Xindi; Shi, Lei; Han, Dezhuan; Zi, Jian; Braun, Paul V.

    2010-05-11

    A 2D polystyrene colloidal crystal self-assembled on a flat gold surface supports multiple photonic and plasmonic propagating resonance modes. For both classes of modes, the quality factors can exceed 100, higher than the quality factor of surface plasmons (SP) at a polymer–gold interface. The spatial energy distribution of those resonance modes are carefully studied by measuring the optical response of the hybrid plasmonic–photonic crystal after coating with dielectric materials under different coating profiles. Computer simulations with results closely matching those of experiments provide a clear picture of the field distribution of each resonance mode. For the SP modes, there is strong confinement of electromagnetic energy near the metal surface, while for optical modes, the field is confined inside the spherical particles, far away from the metal. Coating of dielectric material on the crystal results in a large shift in optical features. A surface sensor based on the hybrid plasmonic–photonic crystal is proposed, and it is shown to have atomic layer sensitivity. An example of ethanol vapor sensing based on physisorption of ethanol onto the sensor surface is demonstrated.

  19. Nonreciprocal optical properties in resonant hybrid photonic crystals

    NASA Astrophysics Data System (ADS)

    D'Andrea, A.; Tomassini, N.

    2016-07-01

    The present work is devoted to the theoretical study of the nonreciprocal optical properties in hybrid (isotropic and anisotropic) periodic multilayers for photon energy values chosen close to the electronic energy gaps of semiconductors (excitons). The optical properties of these resonant nonmagnetic photonic crystals, where linear and quadratic spatial dispersion effects are both present, will be studied in the framework of exciton-polariton self-consistent solutions of the Maxwell and Schrödinger equations in the effective-mass approximation. The main interesting optical properties, namely, giant transmission, absorption suppression, and optical unidirectional propagation, will be computed by implementing a two-layer "minimum model."

  20. One-dimensional parabolic-beam photonic crystal laser.

    PubMed

    Ahn, Byeong-Hyeon; Kang, Ju-Hyung; Kim, Myung-Ki; Song, Jung-Hwan; Min, Bumki; Kim, Ki-Soo; Lee, Yong-Hee

    2010-03-15

    We report one-dimensional (1-D) parabolic-beam photonic crystal (PhC) lasers in which the width of the PhC slab waveguide is parabolically tapered. A few high-Q resonant modes are confirmed in the vicinity of the tapered region where Gaussian-shaped photonic well is formed. These resonant modes originate from the dielectric PhC guided mode and overlap with the gain medium efficiently. It is also shown that the far-field radiation profile is closely associated with the symmetry of the structural perturbation.

  1. Luneburg and flat lens based on graded photonic crystal

    NASA Astrophysics Data System (ADS)

    Liu, Wei; Sun, Xiaohong; Gao, Minglei; Wang, Shuai

    2016-04-01

    Square-lattice graded photonic crystals employed for designing Luneburg and Flat Lens is presented. Comparable simulation of the Luneburg lens with TE and TM polarizations predicts that TM lens possesses of enlarged transmission bandwidth and strengthened focusing ability, in comparison with TE lens. As a typical simplified counterpart, the evolution of focusing intensity and numerical aperture of the flat lens is achieved. What is more, those Luneburg and Flat Lens can withstand imperfect gradients in structure design. This will provide a guidance to produce a high quality focusing lens with small size, short focal length and large numerical aperture applied in the integrated photonic devices.

  2. Generation of higher odd harmonics in a defective photonic crystal

    SciTech Connect

    Ramanujam, N. R.; Wilson, K. S. Joseph

    2015-06-24

    A photonic crystal (AB){sup 2}(DB)(AB){sup 2} with high refractive index medium as silicon and low refractive medium as air is considered. Using the transfer matrix method, the transmission properties as a function of wavelength with photonic band gaps has been obtained. We are able to demonstrate the generation of third, fifth, seventh and ninth harmonics in the present work. We show that if the air medium is removed in the defect, the defect modes are generated but not harmonics. It can be designed to have a frequency conversion, and have a potential for becoming the basis for the next generation of optical devices.

  3. High-Q silicon carbide photonic-crystal cavities

    SciTech Connect

    Lee, Jonathan Y.; Lu, Xiyuan; Lin, Qiang

    2015-01-26

    We demonstrate one-dimensional photonic-crystal nanobeam cavities in amorphous silicon carbide. The fundamental mode exhibits intrinsic optical quality factor as high as 7.69 × 10{sup 4} with mode volume ∼0.60(λ/n){sup 3} at wavelength 1.5 μm. A corresponding Purcell factor value of ∼10{sup 4} is the highest reported to date in silicon carbide optical cavities. The device exhibits great potential for integrated nonlinear photonics and cavity nano-optomechanics.

  4. Holographic polymer-dispersed liquid crystal Bragg grating integrated inside a solid core photonic crystal fiber.

    PubMed

    Zito, Gianluigi; Pissadakis, Stavros

    2013-09-01

    A polymer/liquid crystal-based fiber Bragg grating (PLC-FBG) is fabricated with visible two-beam holography by photo-induced modulation of a prepolymer/liquid crystal solution infiltrated into the hollow channels of a solid core photonic crystal fiber (PCF). The fabrication process and effects related to the photonic bandgap guidance into the infiltrated PCF, and characterization of the PLC-FBG, are discussed. Experimental data presented here demonstrate that the liquid crystal inclusions of the PLC-FBG lead to high thermal and bending sensitivities. The microscopic behavior of the polymer/liquid crystal phase separation inside the PCF capillaries is examined using scanning electron microscopy, and is discussed further. PMID:23988927

  5. Experimental demonstration of self-collimation inside a three-dimensional photonic crystal.

    PubMed

    Lu, Zhaolin; Shi, Shouyuan; Murakowski, Janusz A; Schneider, Garrett J; Schuetz, Christopher A; Prather, Dennis W

    2006-05-01

    We present our experimental demonstration of self-collimation inside a three-dimensional (3D) simple cubic photonic crystal at microwave frequencies. The photonic crystal was designed with unique dispersion property and fabricated by a high precision computer-controlled machine. The self-collimation modes were excited by a grounded waveguide feeding and detected by a scanning monopole. Self-collimation of electromagnetic waves in the 3D photonic crystal was demonstrated by measuring the 3D field distribution, which was shown as a narrow collimated beam inside the 3D photonic crystal but a diverged beam in the absence of the photonic crystal. PMID:16712297

  6. Electromagnetic Wave Propagation in Two-Dimensional Photonic Crystals

    SciTech Connect

    Stavroula Foteinopoulou

    2003-12-12

    In this dissertation, they have undertaken the challenge to understand the unusual propagation properties of the photonic crystal (PC). The photonic crystal is a medium where the dielectric function is periodically modulated. These types of structures are characterized by bands and gaps. In other words, they are characterized by frequency regions where propagation is prohibited (gaps) and regions where propagation is allowed (bands). In this study they focus on two-dimensional photonic crystals, i.e., structures with periodic dielectric patterns on a plane and translational symmetry in the perpendicular direction. They start by studying a two-dimensional photonic crystal system for frequencies inside the band gap. The inclusion of a line defect introduces allowed states in the otherwise prohibited frequency spectrum. The dependence of the defect resonance state on different parameters such as size of the structure, profile of incoming source, etc., is investigated in detail. For this study, they used two popular computational methods in photonic crystal research, the Finite Difference Time Domain method (FDTD) and the Transfer Matrix Method (TMM). The results for the one-dimensional defect system are analyzed, and the two methods, FDTD and TMM, are compared. Then, they shift their attention only to periodic two-dimensional crystals, concentrate on their band properties, and study their unusual refractive behavior. Anomalous refractive phenomena in photonic crystals included cases where the beam refracts on the ''wrong'' side of the surface normal. The latter phenomenon, is known as negative refraction and was previously observed in materials where the wave vector, the electric field, and the magnetic field form a left-handed set of vectors. These materials are generally called left-handed materials (LHM) or negative index materials (NIM). They investigated the possibility that the photonic crystal behaves as a LHM, and how this behavior relates with the observed

  7. Magneto-optical properties of biogenic photonic crystals in algae

    SciTech Connect

    Iwasaka, M.; Mizukawa, Y.

    2014-05-07

    In the present study, the effects of strong static magnetic fields on the structural colors of the cell covering crystals on a microalgae, coccolithophore, were investigated. The coccolithophore, Emiliania huxleyi, generates a precise assembly of calcite crystals called coccoliths by biomineralization. The coccoliths attached to the cells exhibited structural colors under side light illumination, and the colors underwent dynamic transitions when the magnetic fields were changed between 0 T and 5 T, probably due to diamagnetically induced changes of their inclination under the magnetic fields. The specific light-scattering property of individual coccoliths separated from the cells was also observed. Light scattering from a condensed suspension of coccoliths drastically decreased when magnetic fields of more than 4 T were applied parallel to the direction of observation. The magnetically aligned cell-covering crystals of the coccolithophores exhibited the properties of both a photonic crystal and a minimum micromirror.

  8. Two-dimensional photonic crystals constructed with a portion of photonic quasicrystals.

    PubMed

    Yang, Yi; Wang, Guo Ping

    2007-05-14

    Photonic quasicrystals (PQs) can produce interesting photonic properties but the lack of periodicity in structures makes exact prediction on their photonic band structures (PBSs) a fundamental challenge currently. Here, we propose a kind of complex two-dimensional photonic crystal (PC) structures constructed with a small portion of different PQs for the purposes of overcoming the difficulty of numerical calculations on the PBSs but maintaining photonic properties of the original PQs owned. Theoretically calculated results on PBSs of the complex PC with a local feature consistent with 12-fold rotational symmetry show that, in the cases of dielectric cylinders in air, air-holes in a dielectric, and metal cylinders in air, respectively, the complex PC can indeed produce similar photonic properties of the original 12-fold PQ such as uniform or isotropic PBGs under much lower dielectric contrast etc. The complex PCs can be constructed with the local parts of n-fold symmetric PQs and should provide a way for creating novel photonic functional materials.

  9. Photonics of liquid-crystal structures: A review

    SciTech Connect

    Palto, S. P. Blinov, L. M.; Barnik, M. I.; Lazarev, V. V.; Umanskii, B. A.; Shtykov, N. M.

    2011-07-15

    The original results of studies of the electro-optical and laser effects which have been performed at the Laboratory of Liquid Crystals of the Institute of Crystallography, Russian Academy of Sciences, over the last few years are reviewed. Cholesteric liquid crystals as vivid representatives of photonic structures and their behavior in an electric field are considered in detail. The formation of higher harmonics in the periodic distribution of the director field in a helical liquid crystal structure and, correspondingly, the new (anharmonic) mode of electro-optical effects are discussed. Another group of studies is devoted to bistable light switching by an electric field in chiral nematics. Polarization diffraction gratings controlled by an electric field are also considered. The results of studies devoted to microlasers on various photonic structures with cholesteric and nematic liquid crystals are considered in detail. Particular attention is given to the new regime: leaky-mode lasing. Designs of liquid crystal light amplifiers and their polarization, field, and spectral characteristics are considered in the last section.

  10. Ultra-compact photonic crystal based water temperature sensor

    NASA Astrophysics Data System (ADS)

    Nikoufard, Mahmoud; Kazemi Alamouti, Masoud; Adel, Alireza

    2016-09-01

    We design an ultra-compact water temperature sensor by using the photonic crystal technology on the InP substrate at the 1.55-μm wavelength window. The photonic crystal consists of rods in a hexagonal lattice and a polymethyl methacrylate (PMMA) background. By using the plane wave expansion (PWE) method, the lattice constant and radius of rods are obtained, 520 nm and 80.6 nm, respectively. With a nanocavity placed in the waveguide, a resonance peak is observed at the 1.55-μm wavelength window. Any change of the water temperature inside the nanocavity results in the shift of the resonance wavelength. Our simulations show a shift of about 11 nm for a temperature change of 22.5 ℃. The resonance wavelength has a linear relation with the water temperature.

  11. Silicon photonic crystal resonators for label free biosensor

    NASA Astrophysics Data System (ADS)

    Sana, Amrita Kumar; Honzawa, Keita; Amemiya, Yoshiteru; Yokoyama, Shin

    2016-04-01

    We report the fabrication and characterization of a two-dimensional (2D) silicon photonic crystal biosensor consisting of waveguides and cavity-type and defect-type resonators for enhancing the interactions between light and biomaterials. Sensitivity was measured using sucrose solution and the sensor showed the highest sensitivity [1570 nm/RIU (refractive index unit)] ever reported. We also investigated cavity size effects on resonance wavelength shift, and we observed that a large cavity exhibits a greater resonance wavelength shift. The fabricated sensor has shown a high Q of ∼105 in water and a device figure of merit of 1.2 × 105, which represent the improvements of the device performance over other photonic-crystal-based sensors.

  12. Negative refraction in one-dimensional photonic crystals

    NASA Astrophysics Data System (ADS)

    Lugo, J. E.; Doti, Rafael; Faubert, J.

    2012-10-01

    Photonic crystals are artificial structures that have periodic dielectric components with different refractive indices. Under certain conditions, they abnormally refract the light, a phenomenon called negative refraction. Here, we discuss recent theoretical and simulation results that showed that negative refraction could be present near the low frequency edge of at least the second, fourth and sixth bandgaps of a lossless one-dimensional photonic crystals (1DPC) structure. That is, negative refraction is a multiband phenomenon. We also discuss the negative refraction correctness condition that gives the angular region where negative refraction occurs. We compare two current negative refraction theoretical models with recent experimental results. In order to succeed, an output refraction correction is utilized. The correction uses Snell's law and an effective refractive index based on two effective dielectric constants. We found good agreement between experiment and both theoretical models in the negative refraction zone.

  13. Tunable ultracompact electro-optical photonic crystal ring resonator

    NASA Astrophysics Data System (ADS)

    Liu, Cheng-Yang

    2013-09-01

    A tunable ultracompact electro-optical photonic crystal ring resonator with high transmission is reported. The photonic crystal ring resonator is obtained by removing a ring shape of cylinders from a square lattice of dielectric cylinders in air. The transmission spectra of this ring resonator have been investigated by using the finite-difference time-domain technique. The general characteristics of the ring elements to achieve resonant tunneling are determined. By modulating the conductibility of the inner cylinders in the ring resonator, the electrical tunability of the resonant modes is observed in the transmission spectrum. The research results should open opportunities for this ring resonator as ultracompact filters, optical add-drop multiplexers, electro-optical N × N switches, and modulators.

  14. Hollow-core photonic-crystal fibres for laser dentistry

    NASA Astrophysics Data System (ADS)

    Konorov, Stanislav O.; Mitrokhin, Vladimir P.; Fedotov, Andrei B.; Sidorov-Biryukov, Dmitrii A.; Beloglazov, Valentin I.; Skibina, Nina B.; Wintner, Ernst; Scalora, Michael; Zheltikov, Aleksei M.

    2004-04-01

    Hollow-core photonic-crystal fibres (PCFs) for the delivery of high-fluence laser radiation capable of ablating tooth enamel are developed. Sequences of picosecond pulses of 1.06 µm Nd:YAG-laser radiation with a total energy of about 2 mJ are transmitted through a hollow-core photonic-crystal fibre with a core diameter of approximately 14 µm and are focused on a tooth surface in vitro to ablate dental tissue. The hollow-core PCF is shown to support the single-fundamental-mode regime for 1.06 µm laser radiation, serving as a spatial filter and allowing the laser beam quality to be substantially improved. The same fibre is used to transmit emission from plasmas produced by laser pulses on the tooth surface in the backward direction for detection and optical diagnostics.

  15. Optofluidic sensor using two-dimensional photonic crystal waveguides

    NASA Astrophysics Data System (ADS)

    Bougriou, Faida; Bouchemat, Touraya; Bouchemat, Mohamed; Paraire, Nicole

    2013-04-01

    Photonic crystal (PC) waveguide is one class of PC devices that has been demonstrated for RI measurements. In this paper, we have reported a new design of infiltrated optofluidic sensors based on 2D photonic crystal slab with triangular lattice pattern of ring-shaped holes. The properties of the sensor are simulated using the finite-difference time-domain (FDTD) method. The transmission spectra have been measured by changing the refractive index of holes and it has been found that with increasing refractive index, wavelength position of transmission spectrum shifts. The radius and the shape of the air holes localized at each side of the line defect are optimized to realize high sensitivity, wide measurement range and improved transmission. An improved optofluidic sensor design is also described and a 210 nm wavelength position of upper band edge shift was observed corresponding to a sensitivity of more than 636 nm per refractive index unit (RIU).

  16. Two-dimensional photonic crystal based sensor for pressure sensing

    NASA Astrophysics Data System (ADS)

    Vijaya Shanthi, Krishnan; Robinson, Savarimuthu

    2014-09-01

    In this paper, a two-dimensional photonic crystal (2DPC) based pressure sensor is proposed and designed, and the sensing characteristics such as the sensitivity and dynamic range are analyzed over the range of pressure from 0 GPa to 7 GPa. The sensor is based on 2DPC with the square array of silicon rods surrounded by air. The sensor consists of two photonic crystal quasi waveguides and L3 defect. The L3 defect is placed in between two waveguides and is formed by modifying the radius of three Si rods. It is noticed that through simulation, the resonant wavelength of the sensor is shifted linearly towards the higher wavelength region while increasing the applied pressure level. The achieved sensitivity and dynamic range of the sensor is 2 nm/GPa and 7 Gpa, respectively.

  17. Method to fabricate a tilted logpile photonic crystal

    DOEpatents

    Williams, John D.; Sweatt, William C.

    2010-10-26

    A method to fabricate a tilted logpile photonic crystal requires only two lithographic exposures and does not require mask repositioning between exposures. The mask and photoresist-coated substrate are spaced a fixed and constant distance apart using a spacer and the stack is clamped together. The stack is then tilted at a crystallographic symmetry angle (e.g., 45 degrees) relative to the X-ray beam and rotated about the surface normal until the mask is aligned with the X-ray beam. The stack is then rotated in plane by a small stitching angle and exposed to the X-ray beam to pattern the first half of the structure. The stack is then rotated by 180.degree. about the normal and a second exposure patterns the remaining half of the structure. The method can use commercially available DXRL scanner technology and LIGA processes to fabricate large-area, high-quality tilted logpile photonic crystals.

  18. Ultra-compact photonic crystal based polarization rotator.

    PubMed

    Bayat, Khadijeh; Chaudhuri, Sujeet K; Safavi-Naeini, Safieddin

    2009-04-27

    An asymmetrically loaded photonic crystal based polarization rotator has been introduced, designed and simulated. The polarization rotator structure consists of a single defect line photonic crystal slab waveguide with asymmetrically etched upper layer. To continue the rotation from a given input polarization to the desired output polarization the upper layer is alternated on either side of the defect line, periodically. Coupled mode theory based on semi-vectorial modes and plane wave expansion methods are employed to design the polarization rotator structure around a particular frequency band of interest. The 3D-FDTD simulation results agree with the coupled mode analysis around the region of interest specified during the design. Complete polarization rotation is achieved over the propagation length of 12lambda. For this length, the coupling efficiency higher than 90% is achieved within the normalized frequency band of 0.258-0.262.

  19. Photonic Crystal Hydrogel Enhanced Plasmonic Staining for Multiplexed Protein Analysis.

    PubMed

    Mu, Zhongde; Zhao, Xiangwei; Huang, Yin; Lu, Meng; Gu, Zhongze

    2015-12-01

    Plasmonic nanoparticles are commonly used as optical transducers in sensing applications. The optical signals resulting from the interaction of analytes and plamsonic nanoparticles are influenced by surrounding physical structures where the nanoparticles are located. This paper proposes inverse opal photonic crystal hydrogel as 3D structure to improve Raman signals from plasmonic staining. By hybridization of the plasmonic nanoparticles and photonic crystal, surface-enhanced Raman spectroscopy (SERS) analysis of multiplexed protein is realized. It benefits the Raman analysis by providing high-density "hot spots" in 3D and extra enhancement of local electromagnetic field at the band edge of PhC with periodic refractive index distribution. The strong interaction of light and the hybrid 3D nanostructure offers new insights into plasmonic nanoparticle applications and biosensor design. PMID:26436833

  20. Large mode-volume, large beta, photonic crystal laser resonator

    SciTech Connect

    Dezfouli, Mohsen Kamandar; Dignam, Marc M.

    2014-12-15

    We propose an optical resonator formed from the coupling of 13, L2 defects in a triangular-lattice photonic crystal slab. Using a tight-binding formalism, we optimized the coupled-defect cavity design to obtain a resonator with predicted single-mode operation, a mode volume five times that of an L2-cavity mode and a beta factor of 0.39. The results are confirmed using finite-difference time domain simulations. This resonator is very promising for use as a single mode photonic crystal vertical-cavity surface-emitting laser with high saturation output power compared to a laser consisting of one of the single-defect cavities.

  1. All-optical information processing in photonic crystals

    NASA Astrophysics Data System (ADS)

    Yanik, Mehmet Fatih

    This thesis covers coherent and incoherent all-optical information processing using photonic bandgap nanostructures and microcavities. The first 3 chapters introduce all-optical bistable switching, transistor and memory elements with sub-micron scale dimensions. A strategy for large scale integration without optical isolators is also described. In chapters 4 and 5, dynamically modulated photonic crystal structures are introduced. It is shown that light pulses can be stopped and stored all-optically without requiring any coherent or resonant light-matter interaction. In chapter 6, it is shown that light pulses can be coherently time-reversed by using only index modulations and linear optics. In chapter 7, a supercomputer implementation of an object oriented finite difference time domain simulation is described to simulate photonic nanostructures with arbitrary material & geometric features.

  2. Defect modes of chiral photonic crystals with an isotropic defect

    NASA Astrophysics Data System (ADS)

    Gevorgyan, A. H.; Oganesyan, K. B.

    2011-06-01

    Specific features of the defect modes of cholesteric liquid crystals (CLCs) with an isotropic defect, as well as their photonic density of states, Q factor, and emission, have been investigated. The effect of the thicknesses of the defect layer and the system as a whole, the position of the defect layer, and the dielectric boundaries on the features of the defect modes have been analyzed. It is shown that when the CLC layer is thin the density of states and emission intensity are maximum for the defect mode, whereas when the CLC layer is thick, these peaks are observed at the edges of the photonic band gap. Similarly, when the gain is low, the density of states and emission intensity are maximum for the defect mode, whereas at high gains these peaks are also observed at the edges of the photonic band gap. The possibilities of low-threshold lasing and obtaining high- Q microcavities have been investigated.

  3. Analysis of two-dimensional photonic crystal with anisotropic gain.

    PubMed

    Takigawa, Shinichi; Noda, Susumu

    2011-05-01

    Photonic modes in a two-dimensional square-lattice photonic crystal (PC) with anisotropic gain are analyzed for the first time. A plane-wave expansion method is improved to include the gain, which depends on not only the position but also the propagation direction of each plane wave. The anisotropic gain varies the photonic band structure, the near-field distributions, and the gain dispersion curves through variation in PC symmetry. Low-threshold operation of a PC laser with anisotropic-gain material such as nonpolar InGaN requires that the direction of higher gain in the material aligns along the ΓX direction of the PC. PMID:21643205

  4. Web-interfaced Nonlinear Optical Waveguide and Photonic Crystal Simulator

    SciTech Connect

    S. Enguehard; B. Hatfield

    2002-06-15

    We report on the development of new methods for the computation of spectral bandpass properties of photonic crystals and for the electromagnetic wave propagation in second order nonlinear optical waveguides. The former is based on a generalization of characteristic matrices while the latter is based on path integrals. Accurate and efficient propagation methods and algorithms form the basis for the construction of design tools for integrated optics.

  5. Method of calculating local dispersion in arbitrary photonic crystal waveguides.

    PubMed

    Dastmalchi, Babak; Mohtashami, Abbas; Hingerl, Kurt; Zarbakhsh, Javad

    2007-10-15

    We introduce a novel method to calculate the local dispersion relation in photonic crystal waveguides, based on the finite-difference time-domain simulation and filter diagonalization method (FDM). In comparison with the spatial Fourier transform method (SFT), the highly local dispersion calculations based on FDM are considerably superior and pronounced. For the first time to our knowledge, the presented numerical technique allows comparing the dispersion in straight and bent waveguides.

  6. Photonic crystal borax competitive binding carbohydrate sensing motif†

    PubMed Central

    Cui, Qingzhou; Muscatello, Michelle M. Ward; Asher, Sanford A.

    2009-01-01

    We developed a photonic crystal sensing method for diol containing species such as carbohydrates based on a poly(vinyl alcohol) (PVA) hydrogel containing an embedded crystalline colloidal array (CCA). The polymerized CCA (PCCA) diffracts visible light. We show that in the presence of borax the diffraction wavelength shifts as the concentration of glucose changes. The diffraction shifts result from the competitive binding of glucose to borate, which reduces the concentration of borate bound to the PVA diols. PMID:19381378

  7. Slow light effect in pinch waveguide in photonic crystal

    NASA Astrophysics Data System (ADS)

    Rani, Preeti; Kalra, Yogita; Sinha, R. K.

    2015-08-01

    In this paper, we have proposed a design for slow light effect in pinch photonic crystal waveguide. The design consists of two dimensional triangular arrangements of air holes in silicon on insulator substrate. From the calculations it has been found out that for the proposed structure the group index is high and group velocity dispersion is low. The confinement of light in the pinch waveguide with slow light effect can be a strong candidate for sensor applications.

  8. Superlensing properties of one-dimensional dielectric photonic crystals

    NASA Astrophysics Data System (ADS)

    Savo, Salvatore; di Gennaro, Emiliano; Andreone, Antonello

    2009-10-01

    We present the experimental observation of the superlensing effect in a slab of a one-dimensional photonic crystal made of tilted dielectric elements. We show that this flat lens can achieve subwavelength resolution in different frequency bands. We also demonstrate that the introduction of a proper corrugation on the lens surface can dramatically improve both the transmission and the resolution of the imaged signal.

  9. Electromechanical tuning of vertically-coupled photonic crystal nanobeams.

    PubMed

    Midolo, L; Yoon, S N; Pagliano, F; Xia, T; van Otten, F W M; Lermer, M; Höfling, S; Fiore, A

    2012-08-13

    We present the design, the fabrication and the characterization of a tunable one-dimensional (1D) photonic crystal cavity (PCC) etched on two vertically-coupled GaAs nanobeams. A novel fabrication method which prevents their adhesion under capillary forces is introduced. We discuss a design to increase the flexibility of the structure and we demonstrate a large reversible and controllable electromechanical wavelength tuning (> 15 nm) of the cavity modes. PMID:23038566

  10. Photonic crystal borax competitive binding carbohydrate sensing motif.

    PubMed

    Cui, Qingzhou; Ward Muscatello, Michelle M; Asher, Sanford A

    2009-05-01

    We developed a photonic crystal sensing method for diol containing species such as carbohydrates based on a poly(vinyl alcohol) (PVA) hydrogel containing an embedded crystalline colloidal array (CCA). The polymerized CCA (PCCA) diffracts visible light. We show that in the presence of borax the diffraction wavelength shifts as the concentration of glucose changes. The diffraction shifts result from the competitive binding of glucose to borate, which reduces the concentration of borate bound to the PVA diols.

  11. Visible high-speed optical transmission over photonic crystal fiber.

    PubMed

    Kurokawa, K; Ieda, K; Tajima, K; Nakajima, K; Shiraki, K; Sankawa, I

    2007-01-22

    We demonstrated high-speed transmission at visible wavelengths over a 1 km photonic crystal fiber (PCF). We achieved a 1 Gbit/s transmission at 783 nm by using the direct modulation of a cost-effective Fabry-Perot laser diode (FP-LD). By employing the external modulation of the longitudinally single-mode grating-stabilized LD, we obtained the first penalty free 10 Gbit/s transmission at 780 nm. PMID:19532256

  12. Ultracompact ring resonator microwave photonic filters based on photonic crystal waveguides.

    PubMed

    Shen, Guansheng; Tian, Huiping; Ji, Yuefeng

    2013-02-20

    We design two microwave photonic filters (notch filter and bandpass filter) based on silicon on insulator (SOI) photonic crystal waveguides for a 60 GHz single-sideband signal radio-over-fiber (ROF) system. By perturbing the radii of the first two rows of holes adjacent to the photonic crystal waveguide, we obtained a broad negligible dispersion bandwidth and a corresponding constant low group velocity. With the slow light effect, the delay line of filters can be significantly reduced while providing the same delay time as fiber based delay lines. The simulation results show that the delay-line length of the notch filter is only about 25.9 μm, and it has a free spectral range of 130 GHz, a baseband width (BW) of 4.12 GHz, and a notch depth of 22 dB. The length of the bandpass filter is 62.4 μm, with a 19.6 dB extinction ratio and a 4.02 GHz BW, and the signal-to-noise ratio requirement of received data can be reduced by 9 dB for the 10(-7) bit-error ratio. Demonstrated microwave photonic crystal filters could be used in a future high-frequency millimeter ROF system. PMID:23434992

  13. Radiative cooling of solar absorbers using a visibly transparent photonic crystal thermal blackbody

    PubMed Central

    Zhu, Linxiao; Raman, Aaswath P.; Fan, Shanhui

    2015-01-01

    A solar absorber, under the sun, is heated up by sunlight. In many applications, including solar cells and outdoor structures, the absorption of sunlight is intrinsic for either operational or aesthetic considerations, but the resulting heating is undesirable. Because a solar absorber by necessity faces the sky, it also naturally has radiative access to the coldness of the universe. Therefore, in these applications it would be very attractive to directly use the sky as a heat sink while preserving solar absorption properties. Here we experimentally demonstrate a visibly transparent thermal blackbody, based on a silica photonic crystal. When placed on a silicon absorber under sunlight, such a blackbody preserves or even slightly enhances sunlight absorption, but reduces the temperature of the underlying silicon absorber by as much as 13 °C due to radiative cooling. Our work shows that the concept of radiative cooling can be used in combination with the utilization of sunlight, enabling new technological capabilities. PMID:26392542

  14. Stamping colloidal photonic crystals: a facile way towards complex pixel colour patterns for sensing and displays.

    PubMed

    Ding, Tao; Smoukov, Stoyan K; Baumberg, Jeremy J

    2015-02-01

    Patterning of colloidal photonic crystals (CPCs) has been strongly investigated in recent years for sensing and image displays. Rather than using traditional template-directed approaches, here microimprint lithography along with convective self-assembly is applied to generate complex CPC patterns that can be adjusted to show single- or dual-colour patterns or composite CPC patterns possessing two different colours. These composite CPC patterns show different wettability with water because of the surface chemistry of the polymers and silica used. This dramatically transforms the structural colours upon liquid infiltration. By mixing different ethanol concentrations with water, the infiltration efficiency can be further improved and easily read out from changes in reflection intensity and spectral peak shifts. Integrating these nano-architectures into devices can thus yield function as image displays and as sensors for solvents.

  15. Radiative cooling of solar absorbers using a visibly transparent photonic crystal thermal blackbody.

    PubMed

    Zhu, Linxiao; Raman, Aaswath P; Fan, Shanhui

    2015-10-01

    A solar absorber, under the sun, is heated up by sunlight. In many applications, including solar cells and outdoor structures, the absorption of sunlight is intrinsic for either operational or aesthetic considerations, but the resulting heating is undesirable. Because a solar absorber by necessity faces the sky, it also naturally has radiative access to the coldness of the universe. Therefore, in these applications it would be very attractive to directly use the sky as a heat sink while preserving solar absorption properties. Here we experimentally demonstrate a visibly transparent thermal blackbody, based on a silica photonic crystal. When placed on a silicon absorber under sunlight, such a blackbody preserves or even slightly enhances sunlight absorption, but reduces the temperature of the underlying silicon absorber by as much as 13 °C due to radiative cooling. Our work shows that the concept of radiative cooling can be used in combination with the utilization of sunlight, enabling new technological capabilities.

  16. Current sensing using circularly birefringent twisted solid-core photonic crystal fiber.

    PubMed

    Beravat, R; Wong, G K L; Xi, X M; Frosz, M H; St J Russell, P

    2016-04-01

    Continuously twisted solid-core photonic crystal fiber (PCF) exhibits pure circular birefringence (optical activity), making it ideal for current sensors based on the Faraday effect. By numerical analysis, we identify the PCF geometry for which the circular birefringence (which scales linearly with twist rate) is a maximum. For silica-air PCF, this occurs at a shape parameter (diameter-to-spacing ratio of the hollow channels) of 0.37 and a scale parameter (spacing-to-wavelength) of 1.51. This result is confirmed experimentally by testing a range of different structures. To demonstrate the effectiveness of twisted PCF as a current sensor, a length of fiber is placed on the axis of a 7.6 cm long solenoid, and the Faraday rotation is measured at different values of dc current. The system is then used to chart the wavelength dependence of the Verdet constant. PMID:27192315

  17. Radiative cooling of solar absorbers using a visibly transparent photonic crystal thermal blackbody.

    PubMed

    Zhu, Linxiao; Raman, Aaswath P; Fan, Shanhui

    2015-10-01

    A solar absorber, under the sun, is heated up by sunlight. In many applications, including solar cells and outdoor structures, the absorption of sunlight is intrinsic for either operational or aesthetic considerations, but the resulting heating is undesirable. Because a solar absorber by necessity faces the sky, it also naturally has radiative access to the coldness of the universe. Therefore, in these applications it would be very attractive to directly use the sky as a heat sink while preserving solar absorption properties. Here we experimentally demonstrate a visibly transparent thermal blackbody, based on a silica photonic crystal. When placed on a silicon absorber under sunlight, such a blackbody preserves or even slightly enhances sunlight absorption, but reduces the temperature of the underlying silicon absorber by as much as 13 °C due to radiative cooling. Our work shows that the concept of radiative cooling can be used in combination with the utilization of sunlight, enabling new technological capabilities. PMID:26392542

  18. FUNDAMENTAL AREAS OF PHENOMENOLOGY (INCLUDING APPLICATIONS): Small-Pitch Kagome Hollow-Core Photonic Crystal Fibre

    NASA Astrophysics Data System (ADS)

    Meng, Jia; Hou, Lan-Tian; Zhou, Gui-Yao; Wang, Kang; Chen, Chao

    2008-08-01

    A hollow-core photonic crystal fibre (HC-PCF) based on small-pitch kagome lattice cladding is designed and fabricated. The pitch of the fibre is only 2.45μm and it corresponds to a region of low normalized frequency which has never been investigated before. Both experiments and calculations show that this kagome HC-PCF has a broad optical transmission band from 400 nm to 900 nm, covering the whole visible and near infrared region of the spectrum. Additionally, the loss curve of the fibre is flat in the visible region and the minimum of the loss achieves 0.16dB/m, which is lower than the loss of the kagome HC-PCFs reported before. Furthermore, this fibre can well confine the modes in the air core. No surface modes can be detected in the surrounding silica of the hollow core.

  19. Organic Light Emitting Diodes with Opal Photonic Crystal Layer and Carbon Nanotube Anode

    NASA Astrophysics Data System (ADS)

    Ovalle Robles, Raquel; Del Rocio Nava, Maria; Williams, Christopher; Zhang, Mei; Fang, Shaoli; Lee, Sergey; Baughman, Ray; Zakhidov, Anvar

    2007-03-01

    We report electroluminescence intensity and spectral changes in light emission from organic light emitting diode (OLEDs) structures, which have thin transparent films of opal photonic crystal (PC). The anode in such PC-OLED is laminated on opal layer from free standing optically transparent multiwall carbon nanotubes (T-CNT) sheets made by dry spinning from CVD grown forests. Silica and polystyrene opal films were grown on glass substrates by vertical sedimentation in colloids in thermal baths and the particle size of opal spheres ranges from 300 nm to 450 nm. The use of T-CNTs, (coated by PEDOT-PSS to avoid shorting) as hole injector, allows to eliminate the use of vacuum deposition of metals and permits to achieve tunneling hole injection regime from CNT tips into Alq^3 emission layer

  20. Fiber Fabry-Perot tip sensor based on multimode photonic crystal fiber

    NASA Astrophysics Data System (ADS)

    Wu, Di; Huang, Yu; Fu, Jian-Yu; Wang, Guo-Yin

    2015-03-01

    We propose a novel Fabry-Perot interferometer (FPI) sensor for simultaneous measurement of refractive index (RI) and temperature based on Fresnel reflection and the thermo-optic effect of silica. The sensor head consists of a short section of multimode photonic crystal fiber (MPCF) and a conventional single mode fiber (SMF), where two thin films are formed by collapsing the air holes of MPCF with a commercialized fusion splicer. Experimental results show that such a device has a linear RI sensitivity of ~21.52 dB/RIU (RI unit) and a linear optical path difference (OPD) temperature sensitivity of ~25 nm/°C. In addition, a high RI resolution of about ~1.7×10-5 is obtained by using the Fourier transformation to decompose the spectral response in different spatial frequencies. Low-cost, easy fabrication and high resolution make it appropriate for practical applications.

  1. Photonic band gaps in one-dimensional magnetized plasma photonic crystals with arbitrary magnetic declination

    SciTech Connect

    Zhang Haifeng; Liu Shaobin; Kong Xiangkun

    2012-12-15

    In this paper, the properties of photonic band gaps and dispersion relations of one-dimensional magnetized plasma photonic crystals composed of dielectric and magnetized plasma layers with arbitrary magnetic declination are theoretically investigated for TM polarized wave based on transfer matrix method. As TM wave propagates in one-dimensional magnetized plasma photonic crystals, the electromagnetic wave can be divided into two modes due to the influence of Lorentz force. The equations for effective dielectric functions of such two modes are theoretically deduced, and the transfer matrix equation and dispersion relations for TM wave are calculated. The influences of relative dielectric constant, plasma collision frequency, incidence angle, plasma filling factor, the angle between external magnetic field and +z axis, external magnetic field and plasma frequency on transmission, and dispersion relation are investigated, respectively, and some corresponding physical explanations are also given. From the numerical results, it has been shown that plasma collision frequency cannot change the locations of photonic band gaps for both modes, and also does not affect the reflection and transmission magnitudes. The characteristics of photonic band gaps for both modes can be obviously tuned by relative dielectric constant, incidence angle, plasma filling factor, the angle between external magnetic field and +z axis, external magnetic field and plasma frequency, respectively. These results would provide theoretical instructions for designing filters, microcavities, and fibers, etc.

  2. Interface-coupled dissolution-precipitation processes allow a photonic crystal to replace an ionic crystal along lattice planes

    NASA Astrophysics Data System (ADS)

    Liesegang, Moritz; Milke, Ralf

    2015-04-01

    of fossil shells replaced by opal-A reveals clues for the understanding of structural and chemical reorganization mechanisms behind silica pseudomorphism. Fundamental knowledge about the highly selective replacement process is absent so far, impeding an adequate interpretation of the observations. The replacement of calcitic shells by amorphous silica spheres (~300 nm in size) is a unique example for the transformation of an ionic to a photonic crystal accompanied by a large size contrast of ions and spheres, respectively, but preserving lattice planes. The observed replication of polysynthetic twinning and cleavage planes of calcite by opal-A spheres indicates that silicification occurs via dissolution of shell material and immediate precipitation of amorphous silica. This follows the interface-coupled dissolution-precipitation mechanism model (Putnis and Putnis, 2007), but requires some modification to allow for open space necessary to form spheres in the 100s-nm size range with a core-shell structure. While sphere growth by a gravitational ordering process is implausible, we assume that the ordered array of monodisperse spheres forms via layer-by-layer deposition. References: Putnis A. and Putnis C.V. (2007), J. Solid State Chem., 180, 1783-1786

  3. Dynamically tunable graphene/dielectric photonic crystal transmission lines

    NASA Astrophysics Data System (ADS)

    Williamson, Ian; Mousavi, S. Hossein; Wang, Zheng

    2015-03-01

    It is well known that graphene supports plasmonic modes with high field confinement and lower losses when compared to conventional metals. Additionally, graphene features a highly tunable conductivity through which the plasmon dispersion can be modulated. Over the years these qualities have inspired a wide range of applications for graphene in the THz and infrared regimes. In this presentation we theoretically demonstrate a graphene parallel plate waveguide (PPWG) that sandwiches a 2D photonic crystal slab. The marriage of these two geometries offers a large two dimensional band gap that can be dynamically tuned over a very broad bandwidth. Our device operates in the low-THz band where the graphene PPWG supports a quasi-TEM mode with a relatively flat attenuation. Unlike conventional photonic crystal slabs, the quasi-TEM nature of the graphene PPWG mode allows the slab thickness to be less than 1/10 of the photonic crystal lattice constant. These features offer up a wealth of opportunities, including tunable metamaterials with a possible platform for large band gaps in 3D structures through tiling and stacking. Additionally, the geometry provides a platform for tunable defect cavities without needing three dimensional periodicity.

  4. Label-Free Biosensor Imaging on Photonic Crystal Surfaces

    PubMed Central

    Zhuo, Yue; Cunningham, Brian T.

    2015-01-01

    We review the development and application of nanostructured photonic crystal surfaces and a hyperspectral reflectance imaging detection instrument which, when used together, represent a new form of optical microscopy that enables label-free, quantitative, and kinetic monitoring of biomaterial interaction with substrate surfaces. Photonic Crystal Enhanced Microscopy (PCEM) has been used to detect broad classes of materials which include dielectric nanoparticles, metal plasmonic nanoparticles, biomolecular layers, and live cells. Because PCEM does not require cytotoxic stains or photobleachable fluorescent dyes, it is especially useful for monitoring the long-term interactions of cells with extracellular matrix surfaces. PCEM is only sensitive to the attachment of cell components within ~200 nm of the photonic crystal surface, which may correspond to the region of most interest for adhesion processes that involve stem cell differentiation, chemotaxis, and metastasis. PCEM has also demonstrated sufficient sensitivity for sensing nanoparticle contrast agents that are roughly the same size as protein molecules, which may enable applications in “digital” diagnostics with single molecule sensing resolution. We will review PCEM’s development history, operating principles, nanostructure design, and imaging modalities that enable tracking of optical scatterers, emitters, absorbers, and centers of dielectric permittivity. PMID:26343684

  5. Far-field coupling in nanobeam photonic crystal cavities

    NASA Astrophysics Data System (ADS)

    Rousseau, Ian; Sánchez-Arribas, Irene; Carlin, Jean-François; Butté, Raphaël; Grandjean, Nicolas

    2016-05-01

    We optimized the far-field emission pattern of one-dimensional photonic crystal nanobeams by modulating the nanobeam width, forming a sidewall Bragg cross-grating far-field coupler. By setting the period of the cross-grating to twice the photonic crystal period, we showed using three-dimensional finite-difference time-domain simulations that the intensity extracted to the far-field could be improved by more than three orders of magnitude compared to the unmodified ideal cavity geometry. We then experimentally studied the evolution of the quality factor and far-field intensity as a function of cross-grating coupler amplitude. High quality factor (>4000) blue (λ = 455 nm) nanobeam photonic crystals were fabricated out of GaN thin films on silicon incorporating a single InGaN quantum well gain medium. Micro-photoluminescence spectroscopy of sets of twelve identical nanobeams revealed a nine-fold average increase in integrated far-field emission intensity and no change in average quality factor for the optimized structure compared to the unmodulated reference. These results are useful for research environments and future nanophotonic light-emitting applications where vertical in- and out-coupling of light to nanocavities is required.

  6. Quantum storage of photonic entanglement in a crystal.

    PubMed

    Clausen, Christoph; Usmani, Imam; Bussières, Félix; Sangouard, Nicolas; Afzelius, Mikael; de Riedmatten, Hugues; Gisin, Nicolas

    2011-01-27

    Entanglement is the fundamental characteristic of quantum physics-much experimental effort is devoted to harnessing it between various physical systems. In particular, entanglement between light and material systems is interesting owing to their anticipated respective roles as 'flying' and stationary qubits in quantum information technologies (such as quantum repeaters and quantum networks). Here we report the demonstration of entanglement between a photon at a telecommunication wavelength (1,338 nm) and a single collective atomic excitation stored in a crystal. One photon from an energy-time entangled pair is mapped onto the crystal and then released into a well-defined spatial mode after a predetermined storage time. The other (telecommunication wavelength) photon is sent directly through a 50-metre fibre link to an analyser. Successful storage of entanglement in the crystal is proved by a violation of the Clauser-Horne-Shimony-Holt inequality by almost three standard deviations (S = 2.64 ± 0.23). These results represent an important step towards quantum communication technologies based on solid-state devices. In particular, our resources pave the way for building multiplexed quantum repeaters for long-distance quantum networks.

  7. Photonic crystal based 2D integrating cell for sensing applications

    NASA Astrophysics Data System (ADS)

    Fohrmann, Lena Simone; Petrov, Alexander Y.; Sommer, Gerrit; Krauss, Thomas; Eich, Manfred

    2016-04-01

    We present a concept of a silicon slab based 2D integrating cell where photonic crystal (PhC) reflectors are used in order to confine light in a two-dimensional area to acquire a long propagation length. The evanescent field of the guided wave can be used for sensing applications. We use FDTD simulations to investigate the dependence of the reflectivity of photonic crystal mirrors with a hexagonal lattice. The reflectivity in ΓM direction demonstrates reduced vertical losses compared to the ΓK direction and can be further improved by adiabatically tapering the hole radii of the photonic crystal. A small hexagonal 2D integrating cell was studied with PhC boundaries oriented in ΓM and ΓK direction. It is shown that average reflectivities of 99% can be obtained in a rectangular 2D cell with optimized reflector design, limited only by residual vertical scattering losses at the PhC boundary. This reflectivity is already comparable to the best metallic reflectors.

  8. Large Area 2D and 3D Colloidal Photonic Crystals Fabricated by a Roll-to-Roll Langmuir-Blodgett Method.

    PubMed

    Parchine, Mikhail; McGrath, Joe; Bardosova, Maria; Pemble, Martyn E

    2016-06-14

    We present our results on the fabrication of large area colloidal photonic crystals on flexible poly(ethylene terephthalate) (PET) film using a roll-to-roll Langmuir-Blodgett technique. Two-dimensional (2D) and three-dimensional (3D) colloidal photonic crystals from silica nanospheres (250 and 550 nm diameter) with a total area of up to 340 cm(2) have been fabricated in a continuous manner compatible with high volume manufacturing. In addition, the antireflective properties and structural integrity of the films have been enhanced via the use of a second roll-to-roll process, employing a slot-die coating of an optical adhesive over the photonic crystal films. Scanning electron microscopy images, atomic force microscopy images, and UV-vis optical transmission and reflection spectra of the fabricated photonic crystals are analyzed. This analysis confirms the high quality of the 2D and 3D photonic crystals fabricated by the roll-to-roll LB technique. Potential device applications of the large area 2D and 3D colloidal photonic crystals on flexible PET film are briefly reviewed. PMID:27218474

  9. Large Area 2D and 3D Colloidal Photonic Crystals Fabricated by a Roll-to-Roll Langmuir-Blodgett Method.

    PubMed

    Parchine, Mikhail; McGrath, Joe; Bardosova, Maria; Pemble, Martyn E

    2016-06-14

    We present our results on the fabrication of large area colloidal photonic crystals on flexible poly(ethylene terephthalate) (PET) film using a roll-to-roll Langmuir-Blodgett technique. Two-dimensional (2D) and three-dimensional (3D) colloidal photonic crystals from silica nanospheres (250 and 550 nm diameter) with a total area of up to 340 cm(2) have been fabricated in a continuous manner compatible with high volume manufacturing. In addition, the antireflective properties and structural integrity of the films have been enhanced via the use of a second roll-to-roll process, employing a slot-die coating of an optical adhesive over the photonic crystal films. Scanning electron microscopy images, atomic force microscopy images, and UV-vis optical transmission and reflection spectra of the fabricated photonic crystals are analyzed. This analysis confirms the high quality of the 2D and 3D photonic crystals fabricated by the roll-to-roll LB technique. Potential device applications of the large area 2D and 3D colloidal photonic crystals on flexible PET film are briefly reviewed.

  10. Real-Time Biomolecular Binding Detection Using a Sensitive Photonic Crystal Biosensor

    PubMed Central

    Guo, Yunbo; Ye, Jing Yong; Divin, Charles; Huang, Baohua; Thomas, Thommey P.; Baker, James R.; Norris, Theodore B.

    2010-01-01

    Real-time measurement of specific biomolecular interactions is critical to many areas of biological research. A number of label-free techniques for directly monitoring biomolecular binding have been developed, but it is still challenging to measure the binding kinetics of very small molecules, to detect low concentrations of analyte molecules, or to detect low affinity interactions. In this study, we report the development of a highly sensitive photonic crystal biosensor for label-free, real-time biomolecular binding analysis. We characterize the performance of this biosensor using a standard streptavidin-biotin binding system. Optimization of the surface functionalization methods for streptavidin immobilization on the silica sensing surface is presented, and the specific binding of biotinylated analyte molecules ranging over 3 orders of magnitude in molecular weight, including very small molecules (<250 Da), DNA oligonucleotides, proteins, and antibodies (>150 000 Da), are detected in real time with a high signal-to-noise ratio. Finally, we document the sensor efficiency for low mass adsorption, as well as multilayered molecular interactions. By all important metrics for sensitivity, we anticipate this photonic crystal biosensor will provide new capabilities for highly sensitive measurements of biomolecular binding. PMID:20486666

  11. The study of thermal tunable coupling between a Superconducting photonic crystal waveguide and semi-circular photonic crystal

    NASA Astrophysics Data System (ADS)

    Oskooi, Somayeh; Barvestani, Jamal

    2016-08-01

    Through the present study, we investigated the light coupling between superconducting photonic crystal waveguide and a semi-circular photonic crystal. By using the finite difference time domain method, we evaluated the coupling efficiency between the mentioned structures at the various temperatures for different waveguide sizes. Calculation demonstrated that the coupling efficiency strongly depended on the temperature of the superconductor. The peak value of the coupling efficiency was influenced by the size of the nearest neighbor rods of waveguide. The results have shown that it is possible to obtain high efficiency at the desired temperature with proper selection of physical parameters in far-infrared frequency region. This structure has great potential in the optical integration and other areas.

  12. Modeling of Photonic Band Gap Crystals and Applications

    SciTech Connect

    Ihab Fathy El-Kady

    2002-08-27

    In this work, the authors have undertaken a theoretical approach to the complex problem of modeling the flow of electromagnetic waves in photonic crystals. The focus is to address the feasibility of using the exciting phenomena of photonic gaps (PBG) in actual applications. The authors start by providing analytical derivations of the computational electromagnetic methods used in their work. They also present a detailed explanation of the physics underlying each approach, as well as a comparative study of the strengths and weaknesses of each method. The Plane Wave expansion, Transfer Matrix, and Finite Difference time Domain Methods are addressed. They also introduce a new theoretical approach, the Modal Expansion Method. They then shift the attention to actual applications. They begin with a discussion of 2D photonic crystal wave guides. The structure addressed consists of a 2D hexagonal structure of air cylinders in a layered dielectric background. Comparison with the performance of a conventional guide is made, as well as suggestions for enhancing it. The studies provide an upper theoretical limit on the performance of such guides, as they assumed no crystal imperfections and non-absorbing media. Next, they study 3D metallic PBG materials at near infrared and optical wavelengths. The main objective is to study the importance of absorption in the metal and the suitability of observing photonic band gaps in such structures. They study simple cubic structures where the metallic scatters are either cubes or interconnected metallic rods. Several metals are studied (aluminum, gold, copper, and silver). The effect of topology is addressed and isolated metallic cubes are found to be less lossy than the connected rod structures. The results reveal that the best performance is obtained by choosing metals with a large negative real part of the dielectric function, together with a relatively small imaginary part. Finally, they point out a new direction in photonic crystal

  13. Image formation by and wave propagation in a photonic crystal

    NASA Astrophysics Data System (ADS)

    Parimi, Patanjali; Vodo, Plarenta; Wentao, Lu; di Gennaro, Emiliano; Sridhar, Srinivas

    2004-03-01

    Negative refraction and imaging by a flat slab of a material are two of the important consequences of lefthanded electromagnetism. In our recent work we have demonstrated negative refraction and imaging by photonic crystals in the microwave frequency range [1]. The details of image formation are intriguing and urge its investigation. We have carried out microwave measurements in a parallel plate waveguide made of a pair of metallic plates. The Photonic crystal is made of alumina rods arranged on a square lattice such that the electric field is parallel to the axis of the rods. The detector is a dipole antenna which is inserted into the waveguide from outside. HP 8510C network analyzer is used to measure the complex transmission coefficient . The intensity maps of vs. probe position are obtained by scanning the probe using an x-y robot, both inside and outside the crystal. The results suggest Bloch wave propagation inside the crystal and that the image formation requires a better understanding than a simple ray diagram following geometric optics. [1] P. V. Parimi et al., Nature, 426, 404 (2003).

  14. Dual curved photonic crystal ring resonator based channel drop filter using two-dimensional photonic crystal structure

    NASA Astrophysics Data System (ADS)

    Chhipa, Mayur Kumar; Dusad, Lalit Kumar

    2016-05-01

    In this paper channel drop filter (CDF) is designed using dual curved photonic crystal ring resonator (PCRR). The photonic band gap (PBG) is calculated by plane wave expansion (PWE) method and the photonic crystal (PhC) based on two dimensional (2D) square lattice periodic arrays of silicon (Si) rods in air structure have been investigated using finite difference time domain (FDTD) method. The number of rods in Z and X directions is 21 and 20 respectively with lattice constant 0.540 nm and rod radius r = 0.1 µm. The channel drop filter has been optimized for telecommunication wavelengths λ = 1.591 µm with refractive indices 3.533. In the designed structure further analysis is also done by changing whole rods refractive index and it has been observed that this filter may be used for filtering several other channels also. The designed structure is useful for CWDM systems. This device may serve as a key component in photonic integrated circuits. The device is ultra compact with the overall size around 123 µm2.

  15. An Experimental Study of the Liesegang Phenomenon and Crystal Growth in Silica Gels.

    ERIC Educational Resources Information Center

    Sharbaugh, Amandus H., III; Sharbaugh, Amandus H., Jr.

    1989-01-01

    Reports on a 30-year-old longitudinal study of reactions in gels. Described are reactions and crystal growth in silica gels and diffusion studies of the Liesegang ring formation. Color photographs showing the reactions and graphs upon the diffusions are presented. (YP)

  16. High-efficiency photonic crystal narrowband thermal emitters

    NASA Astrophysics Data System (ADS)

    Farfan, G. B.; Su, M. F.; Reda Taha, M. M.; El-Kady, I.

    2010-02-01

    Photonic crystals (PhC) are artificial structures fabricated with a periodicity in the dielectric function. This periodic electromagnetic potential results in creation of energy bandgaps where photon propagation is prohibited. PhC structures have promising use in thermal applications if optimized to operate at specific thermal emission spectrum. Here, novel utilization of optimized PhC's in thermal applications is presented. We demonstrate through numerical simulation the modification of the thermal emission spectrum by a metallic photonic crystal (PhC) to create high-efficiency multispectral thermal emitters. These emitters funnel radiation from a broad emission spectrum associated with a Plancklike distribution into a prescribed narrow emission band. A detailed quantitative evaluation of the spectral and power efficiencies of a PhC thermal emitter and its portability across infrared (IR) spectral bands are provided. We show an optimized tungsten PhC with a predominant narrow-band emission profile with an emitter efficiency that is more than double that of an ideal blackbody and ~65-75% more power-efficiency across the IR spectrum. We also report on using optimal three-dimensional Lincoln log photonic crystal (LL-PhC) emitters for thermophotovoltaic (TPV) generation as opposed to using a passive filtering approach to truncate the broadband thermal source emission to match the bandgap of a photovoltaic (PV) cell. The emitter performance is optimized for the 1-2μm PV band using different PhC materials, specifically copper, silver and gold. The use of the proposed PhC in TPV devices can produce significant energy savings not reported before. The optimal design of the PhC geometry is obtained by implementing a variety of optimization methods integrated with artificial intelligence (AI) algorithms.

  17. Criteria of backscattering in chiral one-way photonic crystals

    NASA Astrophysics Data System (ADS)

    Cheng, Pi-Ju; Chang, Shu-Wei

    2016-03-01

    Optical isolators are important devices in photonic circuits. To reduce the unwanted reflection in a robust manner, several setups have been realized using nonreciprocal schemes. In this study, we show that the propagating modes in a strongly-guided chiral photonic crystal (no breaking of the reciprocity) are not backscattering-immune even though they are indeed insensitive to many types of scatters. Without the protection from the nonreciprocity, the backscattering occurs under certain circumstances. We present a perturbative method to calculate the backscattering of chiral photonic crystals in the presence of chiral/achiral scatters. The model is, essentially, a simplified analogy to the first-order Born approximation. Under reasonable assumptions based on the behaviors of chiral photonic modes, we obtained the expression of reflection coefficients which provides criteria for the prominent backscattering in such chiral structures. Numerical examinations using the finite-element method were also performed and the results agree well with the theoretical prediction. From both our theory and numerical calculations, we find that the amount of backscattering critically depends on the symmetry of scatter cross sections. Strong reflection takes place when the azimuthal Fourier components of scatter cross sections have an order l of 2. Chiral scatters without these Fourier components would not efficiently reflect the chiral photonic modes. In addition, for these chiral propagating modes, disturbances at the most significant parts of field profiles do not necessarily result in the most effective backscattering. The observation also reveals what types of scatters or defects should be avoided in one-way applications of chiral structures in order to minimize the backscattering.

  18. Electrically tunable zero dispersion wavelengths in photonic crystal fibers filled with a dual frequency addressable liquid crystal

    NASA Astrophysics Data System (ADS)

    Wahle, Markus; Kitzerow, Heinz-Siegfried

    2015-11-01

    We present a liquid crystal (LC) infiltrated photonic crystal fiber, which enables the electrical tuning of the position of zero dispersion wavelengths (ZDWs). A dual frequency addressable liquid crystal is aligned perpendicular on the inclusion walls of a photonic crystal fiber, which results in an escaped radial director field. The orientation of the LC is controlled by applying an external electric field. Due to the high index of the liquid crystal the fiber guides light by the photonic band gap effect. Multiple ZDWs exist in the visible and near infrared. The positions of the ZDWs can be either blue or red shifted depending on the frequency of the applied voltage.

  19. Electrically tunable zero dispersion wavelengths in photonic crystal fibers filled with a dual frequency addressable liquid crystal

    SciTech Connect

    Wahle, Markus Kitzerow, Heinz-Siegfried

    2015-11-16

    We present a liquid crystal (LC) infiltrated photonic crystal fiber, which enables the electrical tuning of the position of zero dispersion wavelengths (ZDWs). A dual frequency addressable liquid crystal is aligned perpendicular on the inclusion walls of a photonic crystal fiber, which results in an escaped radial director field. The orientation of the LC is controlled by applying an external electric field. Due to the high index of the liquid crystal the fiber guides light by the photonic band gap effect. Multiple ZDWs exist in the visible and near infrared. The positions of the ZDWs can be either blue or red shifted depending on the frequency of the applied voltage.

  20. Photonic crystal ring resonator based optical filters for photonic integrated circuits

    NASA Astrophysics Data System (ADS)

    Robinson, S.

    2014-10-01

    In this paper, a two Dimensional (2D) Photonic Crystal Ring Resonator (PCRR) based optical Filters namely Add Drop Filter, Bandpass Filter, and Bandstop Filter are designed for Photonic Integrated Circuits (PICs). The normalized output response of the filters is obtained using 2D Finite Difference Time Domain (FDTD) method and the band diagram of periodic and non-periodic structure is attained by Plane Wave Expansion (PWE) method. The size of the device is minimized from a scale of few tens of millimeters to the order of micrometers. The overall size of the filters is around 11.4 μm × 11.4 μm which is highly suitable of photonic integrated circuits.

  1. Photonic crystal ring resonator based optical filters for photonic integrated circuits

    SciTech Connect

    Robinson, S.

    2014-10-15

    In this paper, a two Dimensional (2D) Photonic Crystal Ring Resonator (PCRR) based optical Filters namely Add Drop Filter, Bandpass Filter, and Bandstop Filter are designed for Photonic Integrated Circuits (PICs). The normalized output response of the filters is obtained using 2D Finite Difference Time Domain (FDTD) method and the band diagram of periodic and non-periodic structure is attained by Plane Wave Expansion (PWE) method. The size of the device is minimized from a scale of few tens of millimeters to the order of micrometers. The overall size of the filters is around 11.4 μm × 11.4 μm which is highly suitable of photonic integrated circuits.

  2. Modification of Thermal Emission via Metallic Photonic Crystals

    SciTech Connect

    Norris, David J.; Stein, Andreas; George, Steven M.

    2012-07-30

    Photonic crystals are materials that are periodically structured on an optical length scale. It was previously demonstrated that the glow, or thermal emission, of tungsten photonic crystals that have a specific structure - known as the 'woodpile structure' - could be modified to reduce the amount of infrared radiation from the material. This ability has implications for improving the efficiency of thermal emission sources and for thermophotovoltaic devices. The study of this effect had been limited because the fabrication of metallic woodpile structures had previously required a complex fabrication process. In this project we pursued several approaches to simplify the fabrication of metallic photonic crystals that are useful for modification of thermal emission. First, we used the self-assembly of micrometer-scale spheres into colloidal crystals known as synthetic opals. These opals can then be infiltrated with a metal and the spheres removed to obtain a structure, known as an inverse opal, in which a three-dimensional array of bubbles is embedded in a film. Second, we used direct laser writing, in which the focus of an infrared laser is moved through a thin film of photoresist to form lines by multiphoton polymerization. Proper layering of such lines can lead to a scaffold with the woodpile structure, which can be coated with a refractory metal. Third, we explored a completely new approach to modified thermal emission - thin metal foils that contain a simple periodic surface pattern, as shown in Fig. 1. When such a foil is heated, surface plasmons are excited that propagate along the metal interface. If these waves strike the pattern, they can be converted into thermal emission with specific properties.

  3. Hyperspectral optical near-field imaging: Looking graded photonic crystals and photonic metamaterials in color

    NASA Astrophysics Data System (ADS)

    Dellinger, Jean; Van Do, K.; Le Roux, Xavier; de Fornel, Frédérique; Cassan, Eric; Cluzel, Benoît

    2012-10-01

    Using a scanning near-field optical microscope operating with a hyperspectral detection scheme, we report the direct observation of the mirage effect within an on-chip integrated artificial material made of a two dimensional graded photonic crystal. The light rainbow due to the material dispersion is quantified experimentally and quantitatively compared to three dimensional plane wave assisted Hamiltonian optics predictions of light propagation.

  4. Photonic clays: a new family of functional 1D photonic crystals.

    PubMed

    Lotsch, Bettina V; Ozin, Geoffrey A

    2008-10-28

    Clays have shown potential as intelligent optical sensing platforms when integrated into a one-dimensional photonic crystal (PC) environment. The clay component imparts intrinsic functionality to the multilayer system by combining the signature ion exchange with the tunable structural color of photonic crystals, giving rise to environmentally sensitive photonic clay architectures. We have fabricated different Laponite-based 1D PCs and clay defect PCs by simple bottom-up self-assembly methodologies and elaborate their working principles and chemically encoded optical response. Accessibility of the multilayer system to analytes is studied on the background of the barrier properties of clays and diffusion control by the mesoporous oxide layers. The time dependence of analyte uptake and the extent and driving force for analyte release are pointed out and discussed in the context of different interactions between the clay layers and analytes. We demonstrate the possibility of optical cycling associated with repeated analyte uptake and removal processes, rendering photonic clays recyclable and low cost sensing platforms with simple optical read-out.

  5. Tunable photonic band-gaps in one-dimensional photonic crystals containing linear graded index material

    NASA Astrophysics Data System (ADS)

    Singh, Bipin K.; Kumar, Pawan; Pandey, Praveen C.

    2014-12-01

    We have demonstrated control of the photonic band gaps (PBGs) in 1-D photonic crystals using linear graded index material. The analysis of PBG has been done in THz region by considering photonic crystals in the form of ten periods of second, third and fourth generation of the Fibonacci sequence as unit cell. The unit cells are constituted of two kinds of layers; one is taken of linear graded index material and other of normal dielectric material. For this investigation, we used a theoretical model based on transfer matrix method. We have obtained a large number of PBGs and their bandwidths can be tuned by changing the grading profile and thicknesses of linear graded index layers. The number of PBGs increases with increase in the thicknesses of layers and their bandwidths can be controlled by the contrast of initial and final refractive index of the graded layers. In this way, we provide more design freedom for photonic devices such as reflectors, filters, optical sensors, couplers, etc.

  6. A two dimensional silicon-based photonic crystal microcavity biosensor

    NASA Astrophysics Data System (ADS)

    Lee, Mindy; Fauchet, Philippe M.

    2006-08-01

    The optical properties of photonic bandgap (PBG) structures are highly sensitive to environmental variation. PBG structures thus are an attractive platform for biosensing applications. We experimentally demonstrate a label-free biosensor based on a two-dimensional (2-D) photonic crystal microcavity slab. The microcavity is fabricated on a silicon-on-insulator substrate and integrated with tapered ridge waveguides for light coupling. The Finite-Difference Time-Domain (FDTD) method is used to model the sensor. The resonance of the microcavity is designed to be around 1.58 μm. In order to capture the target biological materials, the internal surface of the photonic crystal is first functionalized. Binding of the targets is monitored by observing a red shift of the transmission resonance. The magnitude of the shift depends on the amount of material captured by the internal surface. Compared to 1-D PBG biosensors, 2-D devices require a smaller amount of target material and can accommodate larger targets. Experimental results are compared with the predictions obtained from the FDTD simulations.

  7. Modeling of protein electrophoresis in silica colloidal crystals having brush layers of polyacrylamide

    PubMed Central

    Birdsall, Robert E.; Koshel, Brooke M.; Hua, Yimin; Ratnayaka, Saliya N.; Wirth, Mary J.

    2013-01-01

    Sieving of proteins in silica colloidal crystals of mm dimensions is characterized for particle diameters of nominally 350 and 500 nm, where the colloidal crystals are chemically modified with a brush layer of polyacrylamide. A model is developed that relates the reduced electrophoretic mobility to the experimentally measurable porosity. The model fits the data with no adjustable parameters for the case of silica colloidal crystals packed in capillaries, for which independent measurements of the pore radii were made from flow data. The model also fits the data for electrophoresis in a highly ordered colloidal crystal formed in a channel, where the unknown pore radius was used as a fitting parameter. Plate heights as small as 0.4 μm point to the potential for miniaturized separations. Band broadening increases as the pore radius approaches the protein radius, indicating that the main contribution to broadening is the spatial heterogeneity of the pore radius. The results quantitatively support the notion that sieving occurs for proteins in silica colloidal crystals, and facilitate design of new separations that would benefit from miniaturization. PMID:23229163

  8. Optical diode made from a moving photonic crystal.

    PubMed

    Wang, Da-Wei; Zhou, Hai-Tao; Guo, Miao-Jun; Zhang, Jun-Xiang; Evers, Jörg; Zhu, Shi-Yao

    2013-03-01

    Optical diodes controlling the flow of light are of principal significance for optical information processing. They transmit light from an input to an output, but not in the reverse direction. This breaking of time reversal symmetry is conventionally achieved via Faraday or nonlinear effects. For applications in a quantum network, features such as the abilities of all-optical control, on-chip integration, and single-photon operation are important. Here we propose an all-optical optical diode which requires neither magnetic fields nor strong input fields. It is based on a "moving" photonic crystal generated in a three-level electromagnetically induced transparency medium in which the refractive index of a weak probe is modulated by the moving periodic intensity of a strong standing coupling field with two detuned counterpropagating components. Because of the Doppler effect, the frequency range of the crystal's band gap for the probe copropagating with the moving crystal is shifted from that for the counterpropagating probe. This mechanism is experimentally demonstrated in a room temperature Cs vapor cell. PMID:23496710

  9. Light harvesting in photonic crystals revisited: why do slow photons at the blue edge enhance absorption?

    PubMed

    Deparis, O; Mouchet, S R; Su, B-L

    2015-11-11

    Light harvesting enhancement by slow photons in photonic crystal catalysts or dye-sensitized solar cells is a promising approach for increasing the efficiency of photoreactions. This structural effect is exploited in inverse opal TiO2 photocatalysts by tuning the red edge of the photonic band gap to the TiO2 electronic excitation band edge. In spite of many experimental demonstrations, the slow photon effect is not fully understood yet. In particular, observed enhancement by tuning the blue edge has remained unexplained. Based on rigorous couple wave analysis simulations, we quantify light harvesting enhancement in terms of absorption increase at a specific wavelength (monochromatic UV illumination) or photocurrent increase (solar light illumination), with respect to homogeneous flat slab of equivalent material thickness. We show that the commonly accepted explanation relying on light intensity confinement in high (low) dielectric constant regions at the red (blue) edge is challenged in the case of TiO2 inverse opals because of the sub-wavelength size of the material skeleton. The reason why slow photons at the blue edge are also able to enhance light harvesting is the loose confinement of the field, which leads to significant resonantly enhanced field intensity overlap with the skeleton in both red and blue edge tuning cases, yet with different intensity patterns. PMID:26517229

  10. Light harvesting in photonic crystals revisited: why do slow photons at the blue edge enhance absorption?

    PubMed

    Deparis, O; Mouchet, S R; Su, B-L

    2015-11-11

    Light harvesting enhancement by slow photons in photonic crystal catalysts or dye-sensitized solar cells is a promising approach for increasing the efficiency of photoreactions. This structural effect is exploited in inverse opal TiO2 photocatalysts by tuning the red edge of the photonic band gap to the TiO2 electronic excitation band edge. In spite of many experimental demonstrations, the slow photon effect is not fully understood yet. In particular, observed enhancement by tuning the blue edge has remained unexplained. Based on rigorous couple wave analysis simulations, we quantify light harvesting enhancement in terms of absorption increase at a specific wavelength (monochromatic UV illumination) or photocurrent increase (solar light illumination), with respect to homogeneous flat slab of equivalent material thickness. We show that the commonly accepted explanation relying on light intensity confinement in high (low) dielectric constant regions at the red (blue) edge is challenged in the case of TiO2 inverse opals because of the sub-wavelength size of the material skeleton. The reason why slow photons at the blue edge are also able to enhance light harvesting is the loose confinement of the field, which leads to significant resonantly enhanced field intensity overlap with the skeleton in both red and blue edge tuning cases, yet with different intensity patterns.

  11. Thermo-tunable hybrid photonic crystal fiber based on solution-processed chalcogenide glass nanolayers

    NASA Astrophysics Data System (ADS)

    Markos, Christos

    2016-08-01

    The possibility to combine silica photonic crystal fiber (PCF) as low-loss platform with advanced functional materials, offers an enormous range of choices for the development of fiber-based tunable devices. Here, we report a tunable hybrid silica PCF with integrated As2S3 glass nanolayers inside the air-capillaries of the fiber based on a solution-processed glass approach. The deposited high-index layers revealed antiresonant transmission windows from ~500 nm up to ~1300 nm. We experimentally demonstrate for the first time the possibility to thermally-tune the revealed antiresonances by taking advantage the high thermo-optic coefficient of the solution-processed nanolayers. Two different hybrid fiber structures, with core diameter 10 and 5 μm, were developed and characterized using a supercontinuum source. The maximum sensitivity was measured to be as high as 3.6 nm/°C at 1300 nm. The proposed fiber device could potentially constitute an efficient route towards realization of monolithic tunable fiber filters or sensing elements.

  12. Thermo-tunable hybrid photonic crystal fiber based on solution-processed chalcogenide glass nanolayers.

    PubMed

    Markos, Christos

    2016-01-01

    The possibility to combine silica photonic crystal fiber (PCF) as low-loss platform with advanced functional materials, offers an enormous range of choices for the development of fiber-based tunable devices. Here, we report a tunable hybrid silica PCF with integrated As2S3 glass nanolayers inside the air-capillaries of the fiber based on a solution-processed glass approach. The deposited high-index layers revealed antiresonant transmission windows from ~500 nm up to ~1300 nm. We experimentally demonstrate for the first time the possibility to thermally-tune the revealed antiresonances by taking advantage the high thermo-optic coefficient of the solution-processed nanolayers. Two different hybrid fiber structures, with core diameter 10 and 5 μm, were developed and characterized using a supercontinuum source. The maximum sensitivity was measured to be as high as 3.6 nm/°C at 1300 nm. The proposed fiber device could potentially constitute an efficient route towards realization of monolithic tunable fiber filters or sensing elements. PMID:27538726

  13. Thermo-tunable hybrid photonic crystal fiber based on solution-processed chalcogenide glass nanolayers

    PubMed Central

    Markos, Christos

    2016-01-01

    The possibility to combine silica photonic crystal fiber (PCF) as low-loss platform with advanced functional materials, offers an enormous range of choices for the development of fiber-based tunable devices. Here, we report a tunable hybrid silica PCF with integrated As2S3 glass nanolayers inside the air-capillaries of the fiber based on a solution-processed glass approach. The deposited high-index layers revealed antiresonant transmission windows from ~500 nm up to ~1300 nm. We experimentally demonstrate for the first time the possibility to thermally-tune the revealed antiresonances by taking advantage the high thermo-optic coefficient of the solution-processed nanolayers. Two different hybrid fiber structures, with core diameter 10 and 5 μm, were developed and characterized using a supercontinuum source. The maximum sensitivity was measured to be as high as 3.6 nm/°C at 1300 nm. The proposed fiber device could potentially constitute an efficient route towards realization of monolithic tunable fiber filters or sensing elements. PMID:27538726

  14. The beam splitting in the photonic crystal at a degenerate state

    NASA Astrophysics Data System (ADS)

    Kong, Yan-mei; Jing, Yu-Peng; Chen, Da-peng

    2011-01-01

    In this paper, using the plane-wave expansion and finite difference time-domain methods, the photons behavior in the photonic crystal is investigated. Theoretically, when a polarized wave is incident from the background medium to the photonic crystal, the beam propagation directions in the photonic crystal determined by two methods are approximately same. But in this paper, the results exhibit that there is an additional direction obtained by the finite difference time-domain method compared with the plane-wave expansion. Considering basic physical mechanism of the photon behavior, the present work circumvents the electromagnetic field distribution in the photonic crystal at a degenerate state, which can reasonably explain the phenomenon. Finally, it shows that a photonic crystal can be properly designed to achieve double refraction simultaneously at one frequency, which can also offer new thoughts and foundation for the novel beam splitter that applied to many optical systems.

  15. Photonic crystal design and fabrication assisted by tunable femtosecond oscillator laser

    NASA Astrophysics Data System (ADS)

    Ohlinger, Kristofer B.

    Photonic Crystals have the potential for engineered light interaction as directed by the photonic bandgap, a property that details the prohibited propagation region and ultimately the ability to guide light. A so called, photonics-on-chip, would incorporate arbitrary light guiding with functional elements in one package. The realization of such a device is subject to the fabrication paradigms implemented and this thesis is concerned with holographic lithography as a means for creating polymer photonics crystal templates and two-photon polymerization for incorporating light guiding pathways. In this thesis, the design of the to-be-fabricated structures has been co-opted by computational exploration of the photonic crystals possible under the fabrication paradigms with the photonic bandgap considered as a target for design optimization, and tolerancing. Introduction of defects into photonic crystal templates has been successfully realized with the assistance of a tunable femtosecond oscillator laser after the processing conditions have been investigated and demonstrated.

  16. Formation of discrete pulses using taper defects in photonic crystals

    NASA Astrophysics Data System (ADS)

    Balasubramanian, Sai Venkatesh

    2016-01-01

    A two-dimensional photonic crystal based on a lattice of silicon rods in air with a photonic bandgap in the visible and near-ultraviolet spectra is proposed by removing some of the silicon rods or resizing their radii to create a monotonically varying tapered line defect, thereby pertaining to a case of structure-based nonlinearity and making it possible to operate with low input powers. By properly manipulating the length of the line defect, pulse compression and consequent adiabatic amplification are seen, along with bunching/antibunching of pulses. For certain modes of operation, field confinement is observed, and this leads to the formation of discrete pulses, or light bullets. Such a structure can be used as a multifunctional device, with some of the functionalities being optical nonpumped amplification, frequency upconversion, memory writing, matched termination, and slow wave guiding, which form the major conclusions of the work.

  17. Introducing Defects in Photonic Band-Gap (PBG) Crystals

    SciTech Connect

    Johnson, Elliott C.; /North Dakota State U. /SLAC

    2007-11-07

    Photonic Band-Gap (PBG) fibers are a periodic array of optical materials arranged in a lattice called a photonic crystal. The use of PBG fibers for particle acceleration is being studied by the Advanced Accelerator Research Department (AARD) at SLAC. By introducing defects in such fibers, e.g. removing one or more capillaries from a hexagonal lattice, spatially confined modes suitable for particle acceleration may be created. The AARD has acquired several test samples of PBG fiber arrays with varying refractive index, capillary size, and length from an external vendor for testing. The PBGs were inspected with a microscope and characteristics of the capillaries including radii, spacing, and errors in construction were determined. Transmission tests were performed on these samples using a broad-range spectrophotometer. In addition, detailed E-field simulations of different PBG configurations were done using the CUDOS and RSOFT codes. Several accelerating modes for different configurations were found and studied in detail.

  18. Strong optomechanical interactions in a sliced photonic crystal nanobeam.

    PubMed

    Leijssen, Rick; Verhagen, Ewold

    2015-01-01

    Coupling between mechanical and optical degrees of freedom is strongly enhanced by using subwavelength optical mode profiles. We realize an optomechanical system based on a sliced photonic crystal nanobeam, which combines such highly confined optical fields with a low-mass mechanical mode. Analyzing the transduction of motion and effects of radiation pressure we find the system exhibits a photon-phonon coupling rate g0 /2π ≈ 11.5 MHz, exceeding previously reported values by an order of magnitude. We show that the large optomechanical interaction enables detecting thermal motion with detection noise below that at the standard quantum limit, even in broad bandwidth devices, important for both sensor applications as well as measurement-based quantum control. PMID:26522751

  19. H1 photonic crystal cavities for hybrid quantum information protocols.

    PubMed

    Hagemeier, Jenna; Bonato, Cristian; Truong, Tuan-Anh; Kim, Hyochul; Beirne, Gareth J; Bakker, Morten; van Exter, Martin P; Luo, Yunqiu; Petroff, Pierre; Bouwmeester, Dirk

    2012-10-22

    Hybrid quantum information protocols are based on local qubits, such as trapped atoms, NV centers, and quantum dots, coupled to photons. The coupling is achieved through optical cavities. Here we demonstrate far-field optimized H1 photonic crystal membrane cavities combined with an additional back reflection mirror below the membrane that meet the optical requirements for implementing hybrid quantum information protocols. Using numerical optimization we find that 80% of the light can be radiated within an objective numerical aperture of 0.8, and the coupling to a single-mode fiber can be as high as 92%. We experimentally prove the unique external mode matching properties by resonant reflection spectroscopy with a cavity mode visibility above 50%. PMID:23187235

  20. H1 photonic crystal cavities for hybrid quantum information protocols

    NASA Astrophysics Data System (ADS)

    Hagemeier, Jenna; Bonato, Cristian; Truong, Tuan-Anh; Kim, Hyochul; Beirne, Gareth J.; Bakker, Morten; van Exter, Martin P.; Luo, Yunqiu; Petroff, Pierre; Bouwmeester, Dirk

    2012-10-01

    Hybrid quantum information protocols are based on local qubits, such as trapped atoms, NV centers, and quantum dots, coupled to photons. The coupling is achieved through optical cavities. Here we demonstrate far-field optimized H1 photonic crystal membrane cavities combined with an additional back reflection mirror below the membrane that meet the optical requirements for implementing hybrid quantum information protocols. Using numerical optimization we find that 80% of the light can be radiated within an objective numerical aperture of 0.8, and the coupling to a single-mode fiber can be as high as 92%. We experimentally prove the unique external mode matching properties by resonant reflection spectroscopy with a cavity mode visibility above 50%.

  1. Chirped photonic crystal with different symmetries for asymmetric light propagation

    NASA Astrophysics Data System (ADS)

    Singh, Brahm Raj; Rawal, Swati; Sinha, R. K.

    2016-06-01

    In the present paper, we have carried out analysis of asymmetric light propagation in a chirped photonic crystal waveguide. The designed structures have hexagonal arrangement and square arrangement of silicon rods in air substrate. Dimensions of the defect rods are tailored, so that the proposed design structure works as an optical isolator. The transmission analysis of the structure reveals that it can act as an optical diode. We have plotted the extinction ratio and transmission analysis graphs for the structure, and it has been observed that the maximum output is obtained for telecom wavelength of 1.55 μm. Dispersion curves are obtained using the plane wave expansion method, and the transmission is simulated using finite element method. The proposed structures are applicable for photonic integrated circuits due to their simple and clear operating principle.

  2. Tunable defect mode realized by graphene-based photonic crystal

    NASA Astrophysics Data System (ADS)

    Fu, Jiahui; Chen, Wan; Lv, Bo

    2016-04-01

    In this literature, we propose an active terahertz 1D photonic crystal, which consists of silicon layers and air layers. A graphene sheet is embedded at the interface between dielectric and air. Tunable photonic band gap is realized by changing the Fermi level of graphene. Transmission Matrix Method is utilized to explain the influence of the graphene layer. We also demonstrate that a dielectric slab attached with a thin sheet made of single-negative metamaterial acts like a pure dielectric slab with a thinner thickness. A tunable blue shift of the band gap can be realized by simply applying different chemical potentials on the graphene sheet. This feature can be utilized for the design of tunable high-gain antenna array and force generator in terahertz band.

  3. Strong optomechanical interactions in a sliced photonic crystal nanobeam

    PubMed Central

    Leijssen, Rick; Verhagen, Ewold

    2015-01-01

    Coupling between mechanical and optical degrees of freedom is strongly enhanced by using subwavelength optical mode profiles. We realize an optomechanical system based on a sliced photonic crystal nanobeam, which combines such highly confined optical fields with a low-mass mechanical mode. Analyzing the transduction of motion and effects of radiation pressure we find the system exhibits a photon-phonon coupling rate g0 /2π ≈ 11.5 MHz, exceeding previously reported values by an order of magnitude. We show that the large optomechanical interaction enables detecting thermal motion with detection noise below that at the standard quantum limit, even in broad bandwidth devices, important for both sensor applications as well as measurement-based quantum control. PMID:26522751

  4. Plasmonic gold nanodiscs fabricated into a photonic-crystal nanocavity

    NASA Astrophysics Data System (ADS)

    Sediq, Khalid N.; Coles, David; Fry, Paul W.; Lidzey, David G.

    2016-06-01

    We fabricate and characterise an optical structure consisting of a photonic crystal L3 nanocavity containing two gold nanodisks placed close to a field antinode. We use finite difference time domain (FDTD) modelling to show that the optical properties of the nanocavity are sensitive to the physical separation between the gold nanodisks, and that at reduced separation, the q-factor of a cavity mode polarised parallel to the dimer long-axis is reduced, indicating coupling between the cavity mode and a localised plasmon. Preliminary experimental measurements indeed indicate a damping of the cavity mode in the presence of the dimer; a result consistent with the FDTD modelling. Such a scheme may be used to integrate plasmonic systems into all-optical photonic circuits.

  5. Waveguide-integrated photonic crystal spectrometer with camera readout

    SciTech Connect

    Meng, Fan; Shiue, Ren-Jye; Li, Luozhou; Nie, Jing; Harris, Nicholas C.; Chen, Edward H.; Schröder, Tim; Englund, Dirk; Wan, Noel; Pervez, Nadia; Kymissis, Ioannis

    2014-08-04

    We demonstrate an infrared spectrometer based on waveguide-coupled nanocavity filters in a planar photonic crystal structure. The input light is coupled into the waveguide, from which spectral components are dropped into the cavities and radiated off-chip for detection on a commercial InGaAs camera. The spectrometer has a footprint of only 60 μm by 8 μm. The spectral resolution is about 1 nm in the operation bandwidth of 1522–1545 nm. By substituting the membrane material and structure parameters, this design can be easily extended into the visible regime and developed for a variety of highly efficient, miniature photonic applications.

  6. Beaming of light and enhanced transmission via surface modes of photonic crystals.

    PubMed

    Bulu, Irfan; Caglayan, Humeyra; Ozbay, Ekmel

    2005-11-15

    We report beaming and enhanced transmission of electromagnetic waves by use of surface corrugated photonic crystals. The modes of a finite-size photonic crystal composed of dielectric rods in free space have been analyzed by the plane-wave expansion method. We show the existence of surface propagating modes when the surface of the finite-size photonic crystal is corrugated. We theoretically and experimentally demonstrate that the transmission through photonic crystal waveguides can be substantially increased by the existence of surface propagating modes at the input surface. In addition, the power emitted from the photonic crystal waveguide is confined to a narrow angular region when an appropriate surface corrugation is added to the output surface of the photonic crystal.

  7. A general photonic crystal sensing motif: creatinine in bodily fluids.

    PubMed

    Sharma, Anjal C; Jana, Tushar; Kesavamoorthy, Rasu; Shi, Lianjun; Virji, Mohamed A; Finegold, David N; Asher, Sanford A

    2004-03-10

    We developed a new sensing motif for the detection and quantification of creatinine, which is an important small molecule marker of renal dysfunction. This novel sensor motif is based on our intelligent polymerized crystalline colloidal array (IPCCA) materials, in which a three-dimensional crystalline colloidal array (CCA) of monodisperse, highly charged polystyrene latex particles are polymerized within lightly cross-linked polyacrylamide hydrogels. These composite hydrogels are photonic crystals in which the embedded CCA diffracts visible light and appears intensely colored. Volume phase transitions of the hydrogel cause changes in the CCA lattice spacings which change the diffracted wavelength of light. We functionalized the hydrogel with two coupled recognition modules, a creatinine deiminase (CD) enzyme and a 2-nitrophenol (2NPh) titrating group. Creatinine within the gel is rapidly hydrolyzed by the CD enzyme in a reaction which releases OH(-). This elevates the steady-state pH within the hydrogel as compared to the exterior solution. In response, the 2NPh is deprotonated. The increased solubility of the phenolate species as compared to that of the neutral phenols causes a hydrogel swelling which red-shifts the IPCCA diffraction. This photonic crystal IPCCA senses physiologically relevant creatinine levels, with a detection limit of 6 microM, at physiological pH and salinity. This sensor also determines physiological levels of creatinine in human blood serum samples. This sensing technology platform is quite general. It may be used to fabricate photonic crystal sensors for any species for which there exists an enzyme which catalyzes it to release H(+) or OH(-). PMID:14995215

  8. Array integration of thousands of photonic crystal nanolasers

    NASA Astrophysics Data System (ADS)

    Watanabe, Takumi; Abe, Hiroshi; Nishijima, Yoshiaki; Baba, Toshihiko

    2014-03-01

    Photonic crystal (PC) nanolasers often consist of air-bridge PC slab, which enhances optical confinement while limiting its size to 30 × 30 μm2 due to the mechanical fragileness. This limit is broken by resin-mediated bonding of the PC slab on a host substrate. In this paper, we demonstrate a GaInAsP PC slab with a size of over 100 × 100 μm2 in which 1089, 2376, and 11 664 nanolasers showing high-yield laser operation are integrated.

  9. Application of a photonic crystal fiber LPG for vibration monitoring

    NASA Astrophysics Data System (ADS)

    Nascimento, I. M.; Chesini, G.; Sousa, Marco; Osório, Jonas H.; Baptista, J. M.; Cordeiro, Cristiano M. B.; Jorge, Pedro A. S.

    2013-05-01

    A fiber optic sensor based on a long-period grating (LPG) inscribed in a photonic crystal fiber is investigated for vibration sensing for structural monitoring applications. In this paper, preliminary results are shown demonstrating the sensor ability to detect vibration induced in a test structure. The sensor frequency response when attached to a loudspeaker-acrylic plate stimulation system (tested in the range from 40 Hz to 2.5 kHz) is analyzed using an intensity based scheme with a tunable laser. An alternative interrogation scheme, where the vibration signal is retrieved from a spectral scan, is also demonstrated and analyzed showing promising characteristics for structural health monitoring.

  10. High-Visibility Photonic Crystal Fiber Interferometer as Multifunctional Sensor

    PubMed Central

    Cárdenas-Sevilla, G.A.; Fávero, Fernando C.; Villatoro, Joel

    2013-01-01

    A photonic crystal fiber (PCF) interferometer that exhibits record fringe contrast (∼40 dB) is demonstrated along with its sensing applications. The device operates in reflection mode and consists of a centimeter-long segment of properly selected PCF fusion spliced to single mode optical fibers. Two identical collapsed zones in the PCF combined with its modal properties allow high-visibility interference patterns. The interferometer is suitable for refractometric and liquid level sensing. The measuring refractive index range goes from 1.33 to 1.43 and the maximum resolution is ∼1.6 × 10−5. PMID:23396192

  11. Fluorescence enhancement by heterostructure colloidal photonic crystals with dual stopbands.

    PubMed

    Li, Heng; Wang, Jingxia; Liu, Feng; Song, Yanlin; Wang, Rongming

    2011-04-01

    In this work, we present a facile approach on the remarkable enhancement of fluorescent signal by heterostructure colloidal photonic crystals (PCs) with dual stopbands. The intensity of fluorescent medium on heterostructure PCs with dual stopbands overlapping the excitation wavelength and the emission wavelength of fluorescent medium can be up to 162-fold enhancement in comparison to that on the control sample. Otherwise, parameters of heterostructure PC films such as film thickness or stacking order have important effects on fluorescent signals. The method will be of great significance for developing the highly sensitive fluorescence-based detection.

  12. High-quality-factor photonic crystal ring resonator.

    PubMed

    Zhang, Yong; Zeng, Cheng; Li, Danping; Gao, Ge; Huang, Zengzhi; Yu, Jinzhong; Xia, Jinsong

    2014-03-01

    A design for enhancing the quality (Q) factor of a photonic crystal ring resonator (PCRR) is introduced. The highest Q factor based on simulations is 121,000. The analysis of momentum space distributions of the electric field profile for PCRR resonance shows that a high Q factor of a PCRR is attributed to the reduction of tangential k-vector component inside the leaky region. A high Q factor of 75,200 is experimentally demonstrated for a modified PCRR on a silicon-on-insulator wafer. The high-Q-factor PCRR demonstrated here will be beneficial for channel drop filters, lasers, sensors, and other applications. PMID:24690727

  13. Manipulating radiation beams by symmetry of magnetic photonic crystals.

    PubMed

    Xiao, Chao; Wu, Rui-Xin; Sa, Zhong-Hao; Zou, Da-Yong

    2016-06-27

    We theoretically and experimentally study the radiation of current line source embedded in two-dimensional photonic crystals (PCs) made of ferrite rods. Depending on the symmetry of the PCs, the source radiation working at the band edge of the PCs can be multiple or single beam radiation with narrow beam width. Different ways to change the PC symmetry are proposed. Taking advantage of tunable bandgap of the magnetic PC and by lowering the symmetry of the PC, the radiation direction and its working frequency can be reconfigured by bias magnetic field. Experiments demonstrate the dependence of radiation on the PC symmetry.

  14. All-optical nonlinear switching cell made of photonic crystal.

    PubMed

    Wirth Lima, A; da Silva, Marcio G; Ferreira, A C; Sombra, A S B

    2009-07-01

    We analyze and propose a directional optical coupler embedded in photonic crystal, which is driven by an external command signal. Therefore, this switching cell can work in an all-optical switch. The switching method uses a low-power external command signal, inserted in the central coupling region, which acts as another waveguide. The switching process is based on the change from the bar state to the cross state due to the external command signal. In our simulations we used the plane wave expansion method, finite-difference time-domain method, and our own binary propagation method.

  15. Tailoring supercontinuum generation using highly nonlinear photonic crystal fiber

    NASA Astrophysics Data System (ADS)

    Hossain, M. A.; Namihira, Y.; Islam, M. A.; Razzak, S. M. A.; Hirako, Y.; Miyagi, K.; Kaijage, S. F.; Higa, H.

    2012-09-01

    This paper discusses about the tailoring supercontinuum (SC) generation based on a highly nonlinear germanium (Ge) doped photonic crystal fiber (HNL-GePCF) with all normal group velocity dispersion (GVD). Using finite element method (FEM) with a circular perfectly matched boundary layer (PML), it is shown through simulations that how simply the center wavelength can be shifted from one center point to another after optimizing at a particular wavelength using the proposed HNL-GePCF. Moreover, SC spectra at 1.06, 1.31 and 1.55 μm have been generated using picosecond optical pulses produced from relatively less expensive laser sources.

  16. Threshold Characteristics of Slow-Light Photonic Crystal Lasers.

    PubMed

    Xue, Weiqi; Yu, Yi; Ottaviano, Luisa; Chen, Yaohui; Semenova, Elizaveta; Yvind, Kresten; Mork, Jesper

    2016-02-12

    The threshold properties of photonic crystal quantum dot lasers operating in the slow-light regime are investigated experimentally and theoretically. Measurements show that, in contrast to conventional lasers, the threshold gain attains a minimum value for a specific cavity length. The experimental results are explained by an analytical theory for the laser threshold that takes into account the effects of slow light and random disorder due to unavoidable fabrication imperfections. Longer lasers are found to operate deeper into the slow-light region, leading to a trade-off between slow-light induced reduction of the mirror loss and slow-light enhancement of disorder-induced losses. PMID:26918991

  17. Hybrid plasmon photonic crystal resonance grating for integrated spectrometer biosensor.

    PubMed

    Guo, Hong; Guo, Junpeng

    2015-01-15

    Using nanofabricated hybrid metal-dielectric nanohole array photonic crystal gratings, a hybrid plasmonic optical resonance spectrometer biosensor is demonstrated. The new spectrometer sensor technique measures plasmonic optical resonance from the first-order diffraction rather than via the traditional method of measuring optical resonance from transmission. The resonance spectra measured with the new spectrometer technique are compared with the spectra measured using a commercial optical spectrometer. It is shown that the new optical resonance spectrometer can be used to measure plasmonic optical resonance that otherwise cannot be measured with a regular optical spectrometer. PMID:25679856

  18. Wavefront sensing using a liquid-filled photonic crystal fiber.

    PubMed

    Valente, Denise; Rativa, Diego; Vohnsen, Brian

    2015-05-18

    A novel wavefront sensor based on a microstructural array of waveguides is proposed. The method is based on the sensitivity in light-coupling efficiency to the wavefront gradient present at the entrance aperture of each waveguide in an array, and hence the amount of incident light that couples is influenced by wavefront aberrations. The concept is illustrated with wavefront measurements that have been performed using a liquid-filled photonic crystal fiber (LF-PCF) working as a coherent fiber bundle. The pros and cons of the LF-PCF based sensor are discussed. PMID:26074553

  19. Optical properties of two-dimensional metamaterial photonic crystals

    NASA Astrophysics Data System (ADS)

    Mejía-Salazar, J. R.

    2013-12-01

    In the present work, we theoretically study a 2D photonic crystal (PC) comprised by double negative (DNG) metamaterial cylinders, showing that such a system presents a superior light-matter interaction when compared with their single negative (SNG) plasmonic PC counterparts, suggesting a route to enhance the performance of sensors and photovoltaic cells. On the other hand, we have observed that depending on the frequency, the mode symmetry resembles either the case of SNG electric (SNG-E) or SNG magnetic (SNG-M) PC, suggesting that either the electric or magnetic character of the DNG metamaterial dominates in each case.

  20. Photonic crystal biosensor based on optical surface waves.

    PubMed

    Konopsky, Valery N; Karakouz, Tanya; Alieva, Elena V; Vicario, Chiara; Sekatskii, Sergey K; Dietler, Giovanni

    2013-01-01

    A label-free biosensor device based on registration of photonic crystal surface waves is described. Angular interrogation of the optical surface wave resonance is used to detect changes in the thickness of an adsorbed layer, while an additional simultaneous detection of the critical angle of total internal reflection provides independent data of the liquid refractive index. The abilities of the device are demonstrated by measuring of biotin molecule binding to a streptavidin monolayer, and by measuring association and dissociation kinetics of immunoglobulin G proteins. Additionally, deposition of PSS / PAH polyelectrolytes is recorded in situ resulting calculation of PSS and PAH monolayer thicknesses separately. PMID:23429517

  1. Photonic quasi-crystal fiber with high birefringence

    NASA Astrophysics Data System (ADS)

    Liu, Hongfei; Xiao, Wei; Cai, Weicheng; Liu, Exian; Feng, Bo; Wang, Ziming; Liang, Taiyuan; Wang, Shuo; Liu, Jianjun

    2016-03-01

    A high-birefringence photonic quasi-crystal fiber (HB-PQF) based on SiO2 is proposed. The relationships between birefringence and structure parameters and between beat length and structure parameters are researched by finite difference beam propagation method. With the optimization of fiber structure parameters, the birefringence is 1.4207×10-2, which is two orders of magnitude higher than the normally used fiber when the wavelength is 1.55 μm. The radius of the fiber is 6.5 μm. The HB-PQF in a communication sensor will have important application prospects.

  2. Hybrid plasmon photonic crystal resonance grating for integrated spectrometer biosensor.

    PubMed

    Guo, Hong; Guo, Junpeng

    2015-01-15

    Using nanofabricated hybrid metal-dielectric nanohole array photonic crystal gratings, a hybrid plasmonic optical resonance spectrometer biosensor is demonstrated. The new spectrometer sensor technique measures plasmonic optical resonance from the first-order diffraction rather than via the traditional method of measuring optical resonance from transmission. The resonance spectra measured with the new spectrometer technique are compared with the spectra measured using a commercial optical spectrometer. It is shown that the new optical resonance spectrometer can be used to measure plasmonic optical resonance that otherwise cannot be measured with a regular optical spectrometer.

  3. Detection of endotoxin using a photonic crystal nanolaser

    NASA Astrophysics Data System (ADS)

    Takahashi, Daichi; Hachuda, Shoji; Watanabe, Takumi; Nishijima, Yoshiaki; Baba, Toshihiko

    2015-03-01

    Fast and reliable detection of endotoxin (ET) in medical equipment and pharmaceutical products is an essential precursor to clinical treatment. In this study, we demonstrate the use of shifts in wavelength of photonic crystal nanolasers for sensing the Limulus amebocyte lysate reaction, which is a standard method for detecting ET. From working curves of wavelength shift vs ET concentration, whose correlation factors were as high as 98%, we detected a required concentration of 0.001 EU/ml within 33 min and detected a low concentration of 0.0001 EU/ml.

  4. Coherent thermal conductance of 1-D photonic crystals

    NASA Astrophysics Data System (ADS)

    Tschikin, Maria; Ben-Abdallah, Philippe; Biehs, Svend-Age

    2012-10-01

    We present an exact calculation of coherent thermal conductance in 1-D multilayer photonic crystals using the S-matrix method. In particular, we study the thermal conductance in a bilayer structure of Si/vacuum or Al2O3/vacuum slabs by means of the exact radiative heat flux expression. Based on the results obtained for the Al2O3/vacuum structure we show by comparison with previous works that the material losses and (localized) surface modes supported by the inner layers play a fundamental role and cannot be omitted in the definition of thermal conductance. Our results could have significant implications in the conception of efficient thermal barriers.

  5. Photonic crystal cavity-assisted upconversion infrared photodetector.

    PubMed

    Gan, Xuetao; Yao, Xinwen; Shiue, Ren-Jye; Hatami, Fariba; Englund, Dirk

    2015-05-18

    We describe an upconversion infrared photodetector assisted by a gallium phosphide photonic crystal nanocavity directly coupled to a silicon photodiode. The strongly cavity-enhanced second harmonic signal radiating from the gallium phosphide membrane can thus be efficiently collected by the silicon photodiode, which promises a high photoresponsivity of the upconversion detector as 0.81 A/W with the coupled power of 1W. The integrated upconversion photodetector also functions as a compact autocorrelator with sub-ps resolution for measuring pulse width and chirp.

  6. Experimental Observation of Large Chern Numbers in Photonic Crystals.

    PubMed

    Skirlo, Scott A; Lu, Ling; Igarashi, Yuichi; Yan, Qinghui; Joannopoulos, John; Soljačić, Marin

    2015-12-18

    Despite great interest in the quantum anomalous Hall phase and its analogs, all experimental studies in electronic and bosonic systems have been limited to a Chern number of one. Here, we perform microwave transmission measurements in the bulk and at the edge of ferrimagnetic photonic crystals. Band gaps with large Chern numbers of 2, 3, and 4 are present in the experimental results, which show excellent agreement with theory. We measure the mode profiles and Fourier transform them to produce dispersion relations of the edge modes, whose number and direction match our Chern number calculations. PMID:26722920

  7. Extreme optical confinement in a slotted photonic crystal waveguide

    SciTech Connect

    Caër, Charles; Le Roux, Xavier; Cassan, Eric; Combrié, Sylvain De Rossi, Alfredo

    2014-09-22

    Using Optical Coherence Tomography, we measure the attenuation of slow light modes in slotted photonic crystal waveguides. When the group index is close to 20, the attenuation is below 300 dB cm{sup −1}. Here, the optical confinement in the empty slot is very strong, corresponding to an ultra-small effective cross section of 0.02 μm{sup 2}. This is nearly 10 times below the diffraction limit at λ = 1.5 μm, and it enables an effective interaction with a very small volume of functionalized matter.

  8. Array integration of thousands of photonic crystal nanolasers

    SciTech Connect

    Watanabe, Takumi Abe, Hiroshi; Nishijima, Yoshiaki; Baba, Toshihiko

    2014-03-24

    Photonic crystal (PC) nanolasers often consist of air-bridge PC slab, which enhances optical confinement while limiting its size to 30 × 30 μm{sup 2} due to the mechanical fragileness. This limit is broken by resin-mediated bonding of the PC slab on a host substrate. In this paper, we demonstrate a GaInAsP PC slab with a size of over 100 × 100 μm{sup 2} in which 1089, 2376, and 11 664 nanolasers showing high-yield laser operation are integrated.

  9. Detection of endotoxin using a photonic crystal nanolaser

    SciTech Connect

    Takahashi, Daichi; Hachuda, Shoji; Watanabe, Takumi; Nishijima, Yoshiaki; Baba, Toshihiko

    2015-03-30

    Fast and reliable detection of endotoxin (ET) in medical equipment and pharmaceutical products is an essential precursor to clinical treatment. In this study, we demonstrate the use of shifts in wavelength of photonic crystal nanolasers for sensing the Limulus amebocyte lysate reaction, which is a standard method for detecting ET. From working curves of wavelength shift vs ET concentration, whose correlation factors were as high as 98%, we detected a required concentration of 0.001 EU/ml within 33 min and detected a low concentration of 0.0001 EU/ml.

  10. An ion trap built with photonic crystal fibre technology

    SciTech Connect

    Lindenfelser, F. Keitch, B.; Kienzler, D.; Home, J. P.; Bykov, D.; Uebel, P.; Russell, P. St. J.

    2015-03-15

    We demonstrate a surface-electrode ion trap fabricated using techniques transferred from the manufacture of photonic-crystal fibres. This provides a relatively straightforward route for realizing traps with an electrode structure on the 100 micron scale with high optical access. We demonstrate the basic functionality of the trap by cooling a single ion to the quantum ground state, allowing us to measure a heating rate from the ground state of 787 ± 24 quanta/s. Variation of the fabrication procedure used here may provide access to traps in this geometry with trap scales between 100 μm and 10 μm.

  11. Photonic Crystal Enabled Thermophotovoltaics for a Portable Microgenerator

    NASA Astrophysics Data System (ADS)

    Chan, Walker R.; Stelmakh, Veronika; Waits, Christopher M.; Soljacic, Marin; Joannopoulos, John D.; Celanovic, Ivan

    2015-12-01

    This work presents the design and characterization of a first-of-a-kind millimeter- scale thermophotovoltaic (TPV) system using a metallic microburner, photonic crystal emitter, and low-bandgap photovoltaic (PV) cells. In our TPV system, combustion heats the emitter to incandescence and the resulting thermal radiation is converted to electricity by the low bandgap PV cells. Our motivation is to harness the high specific energy of hydrocarbon fuels at the micro- and millimeter-scale in order to meet the increasing power demands of micro robotics and portable electronics. Our experimental demonstration lays the groundwork for developing a TPV microgenerator as a viable battery replacement.

  12. Threshold Characteristics of Slow-Light Photonic Crystal Lasers

    NASA Astrophysics Data System (ADS)

    Xue, Weiqi; Yu, Yi; Ottaviano, Luisa; Chen, Yaohui; Semenova, Elizaveta; Yvind, Kresten; Mork, Jesper

    2016-02-01

    The threshold properties of photonic crystal quantum dot lasers operating in the slow-light regime are investigated experimentally and theoretically. Measurements show that, in contrast to conventional lasers, the threshold gain attains a minimum value for a specific cavity length. The experimental results are explained by an analytical theory for the laser threshold that takes into account the effects of slow light and random disorder due to unavoidable fabrication imperfections. Longer lasers are found to operate deeper into the slow-light region, leading to a trade-off between slow-light induced reduction of the mirror loss and slow-light enhancement of disorder-induced losses.

  13. Packaging consideration of two-dimensional polymer-based photonic crystals for laser beam steering

    NASA Astrophysics Data System (ADS)

    Dou, Xinyuan; Chen, Xiaonan; Chen, Maggie Yihong; Wang, Alan Xiaolong; Jiang, Wei; Chen, Ray T.

    2009-02-01

    In this paper, we report the theoretical study of polymer-based photonic crystals for laser beam steering which is based on the superprism effect as well as the experiment fabrication of the two dimensional photonic crystals for the laser beam steering. Superprism effect, the principle for beam steering, was separately studied in details through EFC (Equifrequency Contour) analysis. Polymer based photonic crystals were fabricated through double exposure holographic interference method using SU8-2007. The experiment results were also reported.

  14. Enhancement of Light Extracting from GaN-BASED Blue Light Emitting Diodes Using Photonic Crystal

    NASA Astrophysics Data System (ADS)

    Wang, Yan; Wu, Fugen; Zhang, Xin; Yao, Yuanwei; Zhong, Huilin; Yan, Shuya; He, Yun

    Photonic crystal (PC) structures on LED have been known to enhance the light extraction significantly. In this paper, we report the light energy of GaN-based blue lighting emitting diode (LED) with perfect area photonic crystal (PPC) structure and defect area photonic crystal (DPC) structure. As a result, the light extracting energy of LEDs with PPC structure enhanced little compared to that of without PC structure. In addition, the light extracting energy of blue LED with DPC structure was remarkably improved.

  15. Fabrication and optical transmission characteristics of polymers woodpile photonic crystal structures with different crystal planes

    NASA Astrophysics Data System (ADS)

    Chen, Ling-Jing; Dong, Xian-Zi; Zhao, Yuan-Yuan; Zhang, Yong-Liang; Liu, Jie; Zheng, Mei-Ling; Duan, Xuan-Ming; Zhao, Zhen-Sheng

    2015-10-01

    The photonic band gap effect which originates from the translational invariance of the periodic lattice of dielectrics has been widely applied in the technical applications of microwave, telecommunication and visible wavelengths. Among the various examples, polymers based three dimensional (3D) photonic crystals (PhCs) have attracted considerable interest because they can be easily fabricated by femo-second (fs) ultrafast laser direct writing (DLW) method. However, it is difficult to realize complete band gap in polymers PhCs due to the low index contrast between polymers and air. Here, we report the design and experimental realization of light's nonreciprocal propagation in woodpile PhCs fabricated with DLW method. Firstly, we fabricated several polymers woodpile PhCs on glass substrate with different crystal planes. The Fourier transform infrared spectroscopy (FTIR) measurements are in agreement with the theoretical predictions, which proves the validity and the accuracy of our DLW method. Further measurements of the transmission spectra with respect to the incident angle reveal that the surface crystal planes and incident wave vectors play important roles in the optical response. Furthermore, we designed and fabricated a 30° PhC wedge. And we find nonreciprocal transmission effect between the forward and backward waves, resulting from the nonsymmetrical refraction of the light in different planes. Our results may find potential applications in future 3D photonic integrated circuits and pave the way for the fabrication of other photonic and optical devices with DLW method.

  16. Rapid electrostatics-assisted layer-by-layer assembly of near-infrared-active colloidal photonic crystals.

    PubMed

    Askar, Khalid; Leo, Sin-Yen; Xu, Can; Liu, Danielle; Jiang, Peng

    2016-11-15

    Here we report a rapid and scalable bottom-up technique for layer-by-layer (LBL) assembling near-infrared-active colloidal photonic crystals consisting of large (⩾1μm) silica microspheres. By combining a new electrostatics-assisted colloidal transferring approach with spontaneous colloidal crystallization at an air/water interface, we have demonstrated that the crystal transfer speed of traditional Langmuir-Blodgett-based colloidal assembly technologies can be enhanced by nearly 2 orders of magnitude. Importantly, the crystalline quality of the resultant photonic crystals is not compromised by this rapid colloidal assembly approach. They exhibit thickness-dependent near-infrared stop bands and well-defined Fabry-Perot fringes in the specular transmission and reflection spectra, which match well with the theoretical calculations using a scalar-wave approximation model and Fabry-Perot analysis. This simple yet scalable bottom-up technology can significantly improve the throughput in assembling large-area, multilayer colloidal crystals, which are of great technological importance in a variety of optical and non-optical applications ranging from all-optical integrated circuits to tissue engineering. PMID:27494632

  17. Rapid electrostatics-assisted layer-by-layer assembly of near-infrared-active colloidal photonic crystals.

    PubMed

    Askar, Khalid; Leo, Sin-Yen; Xu, Can; Liu, Danielle; Jiang, Peng

    2016-11-15

    Here we report a rapid and scalable bottom-up technique for layer-by-layer (LBL) assembling near-infrared-active colloidal photonic crystals consisting of large (⩾1μm) silica microspheres. By combining a new electrostatics-assisted colloidal transferring approach with spontaneous colloidal crystallization at an air/water interface, we have demonstrated that the crystal transfer speed of traditional Langmuir-Blodgett-based colloidal assembly technologies can be enhanced by nearly 2 orders of magnitude. Importantly, the crystalline quality of the resultant photonic crystals is not compromised by this rapid colloidal assembly approach. They exhibit thickness-dependent near-infrared stop bands and well-defined Fabry-Perot fringes in the specular transmission and reflection spectra, which match well with the theoretical calculations using a scalar-wave approximation model and Fabry-Perot analysis. This simple yet scalable bottom-up technology can significantly improve the throughput in assembling large-area, multilayer colloidal crystals, which are of great technological importance in a variety of optical and non-optical applications ranging from all-optical integrated circuits to tissue engineering.

  18. Wigner Crystallization of Single Photons in Cold Rydberg Ensembles

    NASA Astrophysics Data System (ADS)

    Otterbach, Johannes; Moos, Matthias; Muth, Dominik; Fleischhauer, Michael

    2013-09-01

    The coupling of weak light fields to Rydberg states of atoms under conditions of electromagnetically induced transparency leads to the formation of Rydberg polaritons which are quasiparticles with tunable effective mass and nonlocal interactions. Confined to one spatial dimension their low energy physics is that of a moving-frame Luttinger liquid which, due to the nonlocal character of the repulsive interaction, can form a Wigner crystal of individual photons. We calculate the Luttinger K parameter using density-matrix renormalization group simulations and find that under typical slow-light conditions kinetic energy contributions are too strong for crystal formation. However, adiabatically increasing the polariton mass by turning a light pulse into stationary spin excitations allows us to generate true crystalline order over a finite length. The dynamics of this process and asymptotic correlations are analyzed in terms of a time-dependent Luttinger theory.

  19. Wigner crystallization of single photons in cold Rydberg ensembles.

    PubMed

    Otterbach, Johannes; Moos, Matthias; Muth, Dominik; Fleischhauer, Michael

    2013-09-13

    The coupling of weak light fields to Rydberg states of atoms under conditions of electromagnetically induced transparency leads to the formation of Rydberg polaritons which are quasiparticles with tunable effective mass and nonlocal interactions. Confined to one spatial dimension their low energy physics is that of a moving-frame Luttinger liquid which, due to the nonlocal character of the repulsive interaction, can form a Wigner crystal of individual photons. We calculate the Luttinger K parameter using density-matrix renormalization group simulations and find that under typical slow-light conditions kinetic energy contributions are too strong for crystal formation. However, adiabatically increasing the polariton mass by turning a light pulse into stationary spin excitations allows us to generate true crystalline order over a finite length. The dynamics of this process and asymptotic correlations are analyzed in terms of a time-dependent Luttinger theory. PMID:24074081

  20. Experiment and simulation on one-dimensional plasma photonic crystals

    SciTech Connect

    Zhang, Lin; Ouyang, Ji-Ting

    2014-10-15

    The transmission characteristics of microwaves passing through one-dimensional plasma photonic crystals (PPCs) have been investigated by experiment and simulation. The PPCs were formed by a series of discharge tubes filled with argon at 5 Torr that the plasma density in tubes can be varied by adjusting the discharge current. The transmittance of X-band microwaves through the crystal structure was measured under different discharge currents and geometrical parameters. The finite-different time-domain method was employed to analyze the detailed properties of the microwaves propagation. The results show that there exist bandgaps when the plasma is turned on. The properties of bandgaps depend on the plasma density and the geometrical parameters of the PPCs structure. The PPCs can perform as dynamical band-stop filter to control the transmission of microwaves within a wide frequency range.

  1. Cotton-yarn/TiO {2} dispersed resin photonic crystals with straight and wavy structures

    NASA Astrophysics Data System (ADS)

    Watanabe, Y.; Kobayashi, T.; Kirihara, S.; Miyamoto, Y.; Sakoda, K.

    2004-06-01

    The feasibility of three-dimensional (3-D) photonic crystals made using textile technology was investigated. Three different textures consisting of the cotton-yarn and TiO2 dispersed resin; a crossed linear-yarn laminated fabric, a multi layered woven fabric, and a 3-D woven fabric, were fabricated. The microwave attenuation of the transmission amplitude through these photonic crystals was measured. The straight cotton-yarn as well as the wavy cotton-yarn/TiO2 dispersed resin photonic crystals exhibited band gaps in the 6 to 15 GHz range. Thus, we could fabricate successfully 3-D photonic crystals using textile technology.

  2. Magnetic field sensor based on selectively magnetic fluid infiltrated dual-core photonic crystal fiber

    NASA Astrophysics Data System (ADS)

    Gangwar, Rahul Kumar; Bhardwaj, Vanita; Singh, Vinod Kumar

    2016-02-01

    We reported the modeling result of selectively magnetic fluid infiltrated dual-core photonic crystal fiber based magnetic field sensor. Inside the cross-section of the designed photonic crystal fiber, the two fiber cores filled with magnetic fluid (Fe3O4) form two independent waveguides with mode coupling. The mode coupling under different magnetic field strengths is investigated theoretically. The sensitivity of the sensor as a function of the structural parameters of the photonic crystal fiber is calculated. The result shows that the proposed sensing device with 1 cm photonic crystal fiber length has a large sensitivity of 305.8 pm/Oe.

  3. The method of impedance transformation for electromagnetic waves propagating in one-dimension plasma photonic crystal

    NASA Astrophysics Data System (ADS)

    Yao, Jingfeng; Yuan, Chengxun; Gao, Ruilin; Jia, Jieshu; Wang, Ying; Zhou, Zhongxiang; Wang, Xiaoou; Wu, Jian; Li, Hui

    2016-08-01

    This study focuses on the transmission of normal-incidence electromagnetic waves in one-dimensional plasma photonic crystals. Using the Maxwell's equations in a medium, a method that is based on the concept of impendence is employed to perform the simulation. The accuracy of the method was evaluated by simulating a one-layer plasma and conventional photonic crystal. In frequency-domain, the transmission and reflection coefficients in the unmagnetized plasma photonic crystal were calculated, and the influence factors on plasma photonic crystals including dielectric constants of dielectric, spatial period, filling factor, plasma frequency, and collision frequency were studied.

  4. A photonic crystal ring resonator formed by SOI nano-rods.

    PubMed

    Chiu, Wei-Yu; Huang, Tai-Wei; Wu, Yen-Hsiang; Chan, Yi-Jen; Hou, Chia-Hunag; Chien, Huang Ta; Chen, Chii-Chang

    2007-11-12

    The design, fabrication and measurement of a silicon-on-insulator (SOI) two-dimensional photonic crystal ring resonator are demonstrated in this study. The structure of the photonic crystal is comprised of silicon nano-rods arranged in a hexagonal lattice on an SOI wafer. The photonic crystal ring resonator allows for the simultaneous separation of light at wavelengths of 1.31 and 1.55mum. The device is fabricated by e-beam lithography. The measurement results confirm that a 1.31mum/1.55mum wavelength ring resonator filter with a nano-rod photonic crystal structure can be realized. PMID:19550835

  5. Review on recent progress of three-dimensional optical photonic crystal

    SciTech Connect

    Hsieh, Mei-Li; Kuang, Ping; Bur, James A.; Lin, Shawn-Yu; John, Sajeev

    2014-03-31

    Over the past two decades, the field of photonic-crystals has become one of the most influential realms of contemporary optics. In this paper, we will review two recent experimental progresses in three-dimensional photonic-crystal operating in optical wavelengths. The first is the observation of anomalous light-refraction, an acutely negative refraction, in a 3D photonic-crystal for light trapping, guiding and near-unity absorption. The second is the observation of quasi-coherent thermal emission from an all-metallic 3D photonic-crystal at elevated temperatures.

  6. Bending self-collimated one-way light by using gyromagnetic photonic crystals

    SciTech Connect

    Li, Qing-Bo; Li, Zhen; Wu, Rui-xin

    2015-12-14

    We theoretically demonstrate that electromagnetic waves can self-collimate and propagate unidirectionally in photonic crystals fabricated using semicylindrical ferrite rods in magnetized states. The parity and time-reversal symmetries of such photonic crystals are broken, resulting in a self-collimated one-way body wave within the photonic crystals. By applying the bias magnetic field in a complex configuration, the self-collimated one-way wave beam can be bent into arbitrary trajectories within the photonic crystal, providing an avenue for controlling wave beams.

  7. Chirped photonic crystal mode converters for broad-band coupling with highly dispersive photonic crystal microring resonators

    NASA Astrophysics Data System (ADS)

    Lo, Stanley M.; Lee, Jonathan Y.; Weiss, Sharon M.; Fauchet, Philippe M.

    2014-03-01

    We demonstrate evanescent coupling between a photonic crystal (PhC) waveguide and a PhC embedded microring resonator on the silicon-on-insulator platform. The mode converter comprises 6 linearly chirped air holes that adiabatically couple the light between the silicon waveguide mode and the PhC mode. Three-dimensional finitedifference time-domain simulations reveal a coupling bandwidth of >100nm. From our experiment, the optical spectra show a photonic bandgap located below ~1590nm. At the resonances in the slow-light regime, a loaded quality factor as high as ~2500 was measured and a group index of ~16 in the PhC embedded microring resonator was estimated from the non-uniform free spectral ranges.

  8. Time-reversal constraint limits unidirectional photon emission in slow-light photonic crystals.

    PubMed

    Lang, Ben; Beggs, Daryl M; Oulton, Ruth

    2016-08-28

    Photonic crystal waveguides are known to support C-points-point-like polarization singularities with local chirality. Such points can couple with dipole-like emitters to produce highly directional emission, from which spin-photon entanglers can be built. Much is made of the promise of using slow-light modes to enhance this light-matter coupling. Here we explore the transition from travelling to standing waves for two different photonic crystal waveguide designs. We find that time-reversal symmetry and the reciprocal nature of light places constraints on using C-points in the slow-light regime. We observe two distinctly different mechanisms through which this condition is satisfied in the two waveguides. In the waveguide designs, we consider a modest group velocity of vg≈c/10 is found to be the optimum for slow-light coupling to the C-points.This article is part of the themed issue 'Unifying physics and technology in light of Maxwell's equations'. PMID:27458258

  9. Gyroid photonic crystal with Weyl points: synthesis and mid-infrared photonic characterization

    NASA Astrophysics Data System (ADS)

    Peng, Siying; Khabiboulline, Emil; Zhang, Runyu; Chen, Hongjie; Hon, Philip; Sweatlock, Luke; Braun, Paul; Atwater, Harry

    Weyl points are degenerate energy states resulting from crossings of linear bands in 3D momentum space. Unlike their 2D counterparts, Weyl points are bulk degenerate states that are stable to weak perturbation. The topological surface states associated with Weyl points exhibit unidirectional backscattering-immune transport. Double gyroid photonic crystals with a parity-breaking perturbation are predicted to possess Weyl points. We designed and synthesized single and double gyroid mid-IR photonic crystals composed of a-Si. We characterized them by mid-IR spectroscopy. We observed 100% reflection at 8 μm for single gyroids with unit cell size of 5 μm, in agreement with the predicted photonic bandgap seen in full-wave EM simulations. As the unit cell size of single gyroids changes to 6 μm, the observed reflection peak shifted to 9 μm, also agreeing with simulation. For double gyroids with unit cell size of 5 μm, we observed a 20% decrease in reflection at 8 μm, which could be explained by a new pair of states appearing within the bandgap from our simulation of double gyroids. We use angle-resolved mid-IR spectroscopy with a QCL to characterize Weyl points.

  10. In Situ Crystallization of Al-Containing Silicate Nanosheets on Monodisperse Amorphous Silica Microspheres.

    PubMed

    Okada, Tomohiko; Sueyoshi, Mai; Minamisawa, Hikari M

    2015-12-29

    The fine crystals of an Al-containing layered silicate, whose negative layer charge is generated by an isomorphous substitution in the tetrahedral SiO4 framework, successfully grew on monodisperse amorphous silica microspheres with diameters of 1.0 and 2.6 μm. The fine, plate-like crystals were observed to thoroughly cover the surface of the silica spheres, irrespective of their size, by the hydrothermal reactions of the silica powder in aqueous alkali solution containing Al and Mg ions in a rotating Teflon-lined autoclave. The crystal size increased when the concentration of the precursors was low. The presence of fluorine in the reaction media enlarged the crystalline phase in the direction of the layer stacking while reducing the plate size. The difference in the crystal size affected the kinetics on the hinokitiol desorption in n-hexane from the layered silicates modified with organoammonium ions. The organically modified layered silicate behaved as an exfoliated nanosheet in the nonpolar solvent. The less harmful elements in this hybrid suggest that it can be used in cosmetic and pharmaceutical applications as a drug support, without flaking off the fine layers on the microspherical substrates. PMID:26639090

  11. Cross two photon absorption in a silicon photonic crystal waveguide fiber taper coupler with a physical junction

    SciTech Connect

    Sarkissian, Raymond O'Brien, John

    2015-01-21

    Cross two photon absorption in silicon is characterized using a tapered fiber photonic crystal silicon waveguide coupler. There is a physical junction between the tapered fiber and the waveguide constituting a stand-alone device. This device is used to obtain the spectrum for cross two photon absorption coefficient per unit volume of interaction between photons of nondegenerate energy. The corresponding Kerr coefficient per unit volume of interaction is also experimentally extracted. The thermal resistance of the device is also experimentally determined and the response time of the device is estimated for on-chip all-optical signal processing and data transfer between optical signals of different photon energies.

  12. Two-dimensional crystals of mesoporous silica SBA-15 nanosheets with perpendicular and open channels

    NASA Astrophysics Data System (ADS)

    Yeh, Yi-Qi; Tang, Chih-Yuan; Mou, Chung-Yuan

    2014-11-01

    A preparation of mesoporous silica SBA-15 thin sheets with perpendicular nanochannels (SBA(⊥)) and open ends is reported here. At a synthesis condition of pH = 2 where the silica condensation is extremely slow, micron-sized single-crystal-like hexagonally faceted nanosheets (SBA(⊥)-pH2) with aspect ratio of 10-50 were formed. The nanosheets can attach to each other in sideway to extend the thin sheet. At pH = 5, multi-domain SBA(⊥)-pH5 nanosheets are formed, and stacking attachment of sheets is preferred. Vivid Moiré patterns are observed in large areas of stacked silica sheets, indicating excellent structure order.

  13. Numerical simulation of photonic-crystal tellurite-tungstate glass fibres used in parametric fibre devices

    SciTech Connect

    Sokolov, V O; Plotnichenko, V G; Nazaryants, V O; Dianov, Evgenii M

    2006-01-31

    Using the MIT Photonic-Bands Package to calculate fully vectorial definite-mode eigenmodes of Maxwell's equations with periodic boundary conditions in a plane-wave basis, light propagation is simulated in fibres formed by point defects in two-dimensional periodic lattices of cylindrical holes in a glass or of glass tubes. The holes and gaps between tubes are assumed filled with air. Single-site hexagonal and square lattices are considered, which were most often studied both theoretically and experimentally and are used to fabricate silica photonic-crystal fibres. As a defect, a single vacancy is studied - the absent lattice site (one hole in a glass or one of the tubes are filled with the same glass) and a similar vacancy with nearest neighbours representing holes of a larger diameter. The obtained solutions are analysed by the method of effective mode area. The dependences of the effective refractive index and dispersion of the fundamental mode on the geometrical parameters of a fibre are found. The calculations are performed for tellurite-tungstate 80TeO{sub 2}-20WO{sub 3} glass fibres taking into account the frequency dispersion of the refractive index. (optical fibres)

  14. A Nanofluidic Biosensor Based on Nanoreplica Molding Photonic Crystal

    NASA Astrophysics Data System (ADS)

    Peng, Wang; Chen, Youping; Ai, Wu; Zhang, Dailin

    2016-09-01

    A nanofluidic biosensor based on nanoreplica molding photonic crystal (PC) was proposed. UV epoxy PC was fabricated by nanoreplica molding on a master PC wafer. The nanochannels were sealed between the gratings on the PC surface and a taped layer. The resonance wavelength of PC-based nanofluidic biosensor was used for testing the sealing effect. According to the peak wavelength value of the sensor, an initial label-free experiment was realized with R6g as the analyte. When the PC-based biosensor was illuminated by a monochromatic light source with a specific angle, the resonance wavelength of the sensor will match with the light source and amplified the electromagnetic field. The amplified electromagnetic field was used to enhance the fluorescence excitation result. The enhancement effect was used for enhancing fluorescence excitation and emission when matched with the resonance condition. Alexa Fluor 635 was used as the target dye excited by 637-nm laser source on a configured photonic crystal enhanced fluorescence (PCEF) setup, and an initial PCEF enhancement factor was obtained.

  15. Silicon-based one-dimensional photonic crystal microcavity

    NASA Astrophysics Data System (ADS)

    Chen, San; Qian, Bo; Chen, Kunji; Xu, Jun; Li, Wei; Huang, Xinfan

    2004-12-01

    The layer-by-layer method is employed to prepare a-SiNx:H microcavity structure in a Plasma Enhanced Chemical Vapor Deposition (PECVD) chamber. Measurements of transmittance spectrum of as-grown samples show that the transmittance resonant peak of a cavity mode at 750 nm is introduced into the band gap of one-dimensional photonic crystal distributed Bragg reflectors based on hydrogenated amorphous silicon nitride. Also the PL measurements of a-SiNx:H microcavities are performed. There is a well agreement between the transmittance spectra and the PL of microcavity samples. In order to clarify the microcavity effects on the bulk a-SiNx:H, the PL of a λ/2-thick layer of bulk a-SiNx:H obtained under the same experimental conditions is presented. By comparison, a dramatic narrowing of emission linewidth and enhancement of PL intensity is observed. The wide emission band with 208 nm is strongly narrowed to 17 nm, and the resonant enhancement of the peak PL intensity is about two orders of magnitude with respect to the emission of the λ/2-thick layer of bulk a-SiNx:H. A linewidth of Δλ=17 nm and a quality factor of Q=50 are achieved in our one-dimensional a-SiNx photonic crystal microcavities.

  16. Maximizing Photoluminescence Extraction in Silicon Photonic Crystal Slabs

    NASA Astrophysics Data System (ADS)

    Mahdavi, Ali; Sarau, George; Xavier, Jolly; Paraïso, Taofiq K.; Christiansen, Silke; Vollmer, Frank

    2016-04-01

    Photonic crystal modes can be tailored for increasing light matter interactions and light extraction efficiencies. These PhC properties have been explored for improving the device performance of LEDs, solar cells and precision biosensors. Tuning the extended band structure of 2D PhC provides a means for increasing light extraction throughout a planar device. This requires careful design and fabrication of PhC with a desirable mode structure overlapping with the spectral region of emission. We show a method for predicting and maximizing light extraction from 2D photonic crystal slabs, exemplified by maximizing silicon photoluminescence (PL). Systematically varying the lattice constant and filling factor, we predict the increases in PL intensity from band structure calculations and confirm predictions in micro-PL experiments. With the near optimal design parameters of PhC, we demonstrate more than 500-fold increase in PL intensity, measured near band edge of silicon at room temperature, an enhancement by an order of magnitude more than what has been reported.

  17. Maximizing Photoluminescence Extraction in Silicon Photonic Crystal Slabs

    PubMed Central

    Mahdavi, Ali; Sarau, George; Xavier, Jolly; Paraïso, Taofiq K.; Christiansen, Silke; Vollmer, Frank

    2016-01-01

    Photonic crystal modes can be tailored for increasing light matter interactions and light extraction efficiencies. These PhC properties have been explored for improving the device performance of LEDs, solar cells and precision biosensors. Tuning the extended band structure of 2D PhC provides a means for increasing light extraction throughout a planar device. This requires careful design and fabrication of PhC with a desirable mode structure overlapping with the spectral region of emission. We show a method for predicting and maximizing light extraction from 2D photonic crystal slabs, exemplified by maximizing silicon photoluminescence (PL). Systematically varying the lattice constant and filling factor, we predict the increases in PL intensity from band structure calculations and confirm predictions in micro-PL experiments. With the near optimal design parameters of PhC, we demonstrate more than 500-fold increase in PL intensity, measured near band edge of silicon at room temperature, an enhancement by an order of magnitude more than what has been reported. PMID:27113674

  18. Maximizing Photoluminescence Extraction in Silicon Photonic Crystal Slabs.

    PubMed

    Mahdavi, Ali; Sarau, George; Xavier, Jolly; Paraïso, Taofiq K; Christiansen, Silke; Vollmer, Frank

    2016-01-01

    Photonic crystal modes can be tailored for increasing light matter interactions and light extraction efficiencies. These PhC properties have been explored for improving the device performance of LEDs, solar cells and precision biosensors. Tuning the extended band structure of 2D PhC provides a means for increasing light extraction throughout a planar device. This requires careful design and fabrication of PhC with a desirable mode structure overlapping with the spectral region of emission. We show a method for predicting and maximizing light extraction from 2D photonic crystal slabs, exemplified by maximizing silicon photoluminescence (PL). Systematically varying the lattice constant and filling factor, we predict the increases in PL intensity from band structure calculations and confirm predictions in micro-PL experiments. With the near optimal design parameters of PhC, we demonstrate more than 500-fold increase in PL intensity, measured near band edge of silicon at room temperature, an enhancement by an order of magnitude more than what has been reported. PMID:27113674

  19. Research on VCSEL of single-mode multilayer photonic crystal

    NASA Astrophysics Data System (ADS)

    Li, Wenchao; Liu, Zhengjun; Sha, Xiaopeng

    2010-10-01

    Vertical-Cavity Surface-Emitting Lasers (VCSEL) of single mode have the potential advantage in the domains of optical information network, routing interactions, optical information storage and data transmission for their excellent performance. However, operating on the single-mode model in the whole pumped area is not solved, which impacts the technologies and applications. In this paper, a new research on VCSEL of single mode multilayer photonic crystal is presented. In the structure of photonic crystal, defects in the horizontal direction are provided by the micro-cavity, while the AIR-KTP interface on the top and the KTP-DBR (Distributed Bragg Reflection) interface at the bottom of cavity provide the defects in the vertical direction, which form quantum defects of electron-hole pairs. The PC-VCSEL in the paper has excellent mode-selection characteristics, which can operate continuously at 850nm in single mode. The single-mode suppression ratio (SMSR) of 45dB is obtained in a wide dynamic range. The PC-VCSEL is expected to become a high-power single-mode light in the future.

  20. A Nanofluidic Biosensor Based on Nanoreplica Molding Photonic Crystal.

    PubMed

    Peng, Wang; Chen, Youping; Ai, Wu; Zhang, Dailin

    2016-12-01

    A nanofluidic biosensor based on nanoreplica molding photonic crystal (PC) was proposed. UV epoxy PC was fabricated by nanoreplica molding on a master PC wafer. The nanochannels were sealed between the gratings on the PC surface and a taped layer. The resonance wavelength of PC-based nanofluidic biosensor was used for testing the sealing effect. According to the peak wavelength value of the sensor, an initial label-free experiment was realized with R6g as the analyte. When the PC-based biosensor was illuminated by a monochromatic light source with a specific angle, the resonance wavelength of the sensor will match with the light source and amplified the electromagnetic field. The amplified electromagnetic field was used to enhance the fluorescence excitation result. The enhancement effect was used for enhancing fluorescence excitation and emission when matched with the resonance condition. Alexa Fluor 635 was used as the target dye excited by 637-nm laser source on a configured photonic crystal enhanced fluorescence (PCEF) setup, and an initial PCEF enhancement factor was obtained. PMID:27664018

  1. Multi-Colour Nanowire Photonic Crystal Laser Pixels

    PubMed Central

    Wright, Jeremy B.; Liu, Sheng; Wang, George T.; Li, Qiming; Benz, Alexander; Koleske, Daniel D.; Lu, Ping; Xu, Huiwen; Lester, Luke; Luk, Ting S.; Brener, Igal; Subramania, Ganapathi

    2013-01-01

    Emerging applications such as solid-state lighting and display technologies require micro-scale vertically emitting lasers with controllable distinct lasing wavelengths and broad wavelength tunability arranged in desired geometrical patterns to form “super-pixels”. Conventional edge-emitting lasers and current surface-emitting lasers that require abrupt changes in semiconductor bandgaps or cavity length are not a viable solution. Here, we successfully address these challenges by introducing a new paradigm that extends the laser tuning range additively by employing multiple monolithically grown gain sections each with a different emission centre wavelength. We demonstrate this using broad gain-bandwidth III-nitride multiple quantum well (MQW) heterostructures and a novel top-down nanowire photonic crystal nanofabrication. We obtain single-mode lasing in the blue-violet spectral region with a remarkable 60 nm of tuning (or 16% of the nominal centre wavelength) that is determined purely by the photonic crystal geometry. This approach can be extended to cover the entire visible spectrum. PMID:24135975

  2. Highly luminescent garnets for magneto-optical photonic crystals

    NASA Astrophysics Data System (ADS)

    Grishin, A. M.; Khartsev, S. I.

    2009-09-01

    We compare luminescent properties of several Er-doped garnets as building blocks in all-garnet heteroepitaxial magneto-optical photonic crystals. Pulsed laser deposited La3Ga5O12, Gd3Ga5O12, Y3Fe5O12, and rf-magnetron sputtered Bi3Fe5O12 were chosen to host Er3+ ions on dodecahedral lattice sites. Er substituents with the concentration of 0.5 at. % (0.1 garnet formula units) do not decrease giant Faraday rotation in Bi2.9Er0.1Fe5O12 garnet; meanwhile providing intense room temperature C-band photoluminescence (PL). Fe3+ ion works as a sensitizer for Er resulting in fivefold PL enhancement in iron garnets compared to gallium ones. PL lifetime in gallium garnets is in millisecond range reaching almost 6 ms in Gd2.9Er0.1Ga5O12. We conclude Er substitution in gallium and iron garnet layers used both as Bragg mirrors and microcavities promises magneto-optical photonic crystals to become an active lasing medium.

  3. Demonstration of two-dimensional photonic crystals based on silicon carbide.

    PubMed

    Song, Bong-Shik; Yamada, Shota; Asano, Takashi; Noda, Susumu

    2011-06-01

    We demonstrate two-dimensional photonic crystals of silicon carbide (SiC)-a wide bandgap semiconductor and one of the hardest materials-at near-infrared wavelengths. Although the refractive index of SiC is lower than that of a conventional semiconductor such as GaAs or Si, we show theoretically that a wide photonic bandgap, a broadband waveguide, and a high-quality nanocavity comparable to those of previous photonic crystals can be obtained in SiC photonic crystals. We also develop a process for fabricating SiC-based photonic crystals that experimentally show a photonic bandgap of 200 nm, a waveguide with a 40-nm bandwidth, and a nanocavity with a high quality factor of 4,500. This demonstration should stimulate further development of resilient and stable photonics at high power and high temperature analogous to SiC power electronics.

  4. Effect of implementation of a Bragg reflector in the photonic band structure of the Suzuki-phase photonic crystal lattice.

    PubMed

    Martinez, Luis Javier; Alija, Alfonso Rodriguez; Postigo, Pablo Aitor; Galisteo-López, J F; Galli, Matteo; Andreani, Lucio Claudio; Seassal, Christian; Viktorovitch, Pierre

    2008-06-01

    We investigate the change of the photonic band structure of the Suzuki-phase photonic crystal lattice when the horizontal mirror symmetry is broken by an underlying Bragg reflector. The structure consists of an InP photonic crystal slab including four InAsP quantum wells, a SiO(2) bonding layer, and a bottom high index contrast Si/SiO(2) Bragg mirror deposited on a Si wafer. Angle- and polarization-resolved photoluminescence spectroscopy has been used for measuring the photonic band structure and for investigating the coupling to a polarized plane wave in the far field. A drastic change in the k-space photonic dispersion between the structure with and without Bragg reflector is measured. An important enhancement on the photoluminescence emission up to seven times has been obtained for a nearly flat photonic band, which is characteristic of the Suzuki-phase lattice.

  5. Experimental GVD engineering in slow light slot photonic crystal waveguides

    PubMed Central

    Serna, Samuel; Colman, Pierre; Zhang, Weiwei; Le Roux, Xavier; Caer, Charles; Vivien, Laurent; Cassan, Eric

    2016-01-01

    The use in silicon photonics of the new optical materials developed in soft matter science (e.g. polymers, liquids) is delicate because their low refractive index weakens the confinement of light and prevents an efficient control of the dispersion properties through the geometry. We experimentally demonstrate that such materials can be incorporated in 700 μm long slot photonic crystal waveguides, and hence can benefit from both slow-light field enhancement effect and slot-induced ultra-small effective areas. Additionally, we show that their dispersion can be engineered from anomalous to normal regions, along with the presence of multiple zero group velocity dispersion (ZGVD) points exhibiting Normalized Delay Bandwidth Product as high as 0.156. The reported results provide experimental evidence for an accurate control of the dispersion properties of fillable periodical slotted structures in silicon photonics, which is of direct interest for on-chip all-optical data treatment using nonlinear optical effects in hybrid-on-silicon technologies. PMID:27243377

  6. High-Q CMOS-integrated photonic crystal microcavity devices.

    PubMed

    Mehta, Karan K; Orcutt, Jason S; Tehar-Zahav, Ofer; Sternberg, Zvi; Bafrali, Reha; Meade, Roy; Ram, Rajeev J

    2014-01-01

    Integrated optical resonators are necessary or beneficial in realizations of various functions in scaled photonic platforms, including filtering, modulation, and detection in classical communication systems, optical sensing, as well as addressing and control of solid state emitters for quantum technologies. Although photonic crystal (PhC) microresonators can be advantageous to the more commonly used microring devices due to the former's low mode volumes, fabrication of PhC cavities has typically relied on electron-beam lithography, which precludes integration with large-scale and reproducible CMOS fabrication. Here, we demonstrate wavelength-scale polycrystalline silicon (pSi) PhC microresonators with Qs up to 60,000 fabricated within a bulk CMOS process. Quasi-1D resonators in lateral p-i-n structures allow for resonant defect-state photodetection in all-silicon devices, exhibiting voltage-dependent quantum efficiencies in the range of a few 10 s of %, few-GHz bandwidths, and low dark currents, in devices with loaded Qs in the range of 4,300-9,300; one device, for example, exhibited a loaded Q of 4,300, 25% quantum efficiency (corresponding to a responsivity of 0.31 A/W), 3 GHz bandwidth, and 30 nA dark current at a reverse bias of 30 V. This work demonstrates the possibility for practical integration of PhC microresonators with active electro-optic capability into large-scale silicon photonic systems.

  7. Remote macroscopic entanglement on a photonic crystal architecture

    NASA Astrophysics Data System (ADS)

    Flayac, H.; Minkov, M.; Savona, V.

    2015-10-01

    The outstanding progress in nanostructure fabrication and cooling technologies allows what was unthinkable a few decades ago: bringing single-mode mechanical vibrations to the quantum regime. The coupling between photon and phonon excitations is a natural source of nonclassical states of light and mechanical vibrations, and its study within the field of cavity optomechanics is developing lightning fast. Photonic crystal cavities are highly integrable architectures that have demonstrated the strongest optomechanical coupling to date and should therefore play a central role for such hybrid quantum-state engineering. In this context, we propose a realistic heralding protocol for the on-chip preparation of remotely entangled mechanical states, relying on the state-of-the-art optomechanical parameters of a silicon-based nanobeam structure. Pulsed sideband excitation of a Stokes process, combined with single-photon detection, allows the writing of a delocalized mechanical Bell state in the system, signatures of which can then be read out in the optical field. A measure of entanglement in this protocol is provided by the visibility of a characteristic quantum interference pattern in the emitted light.

  8. High-Q CMOS-integrated photonic crystal microcavity devices

    NASA Astrophysics Data System (ADS)

    Mehta, Karan K.; Orcutt, Jason S.; Tehar-Zahav, Ofer; Sternberg, Zvi; Bafrali, Reha; Meade, Roy; Ram, Rajeev J.

    2014-02-01

    Integrated optical resonators are necessary or beneficial in realizations of various functions in scaled photonic platforms, including filtering, modulation, and detection in classical communication systems, optical sensing, as well as addressing and control of solid state emitters for quantum technologies. Although photonic crystal (PhC) microresonators can be advantageous to the more commonly used microring devices due to the former's low mode volumes, fabrication of PhC cavities has typically relied on electron-beam lithography, which precludes integration with large-scale and reproducible CMOS fabrication. Here, we demonstrate wavelength-scale polycrystalline silicon (pSi) PhC microresonators with Qs up to 60,000 fabricated within a bulk CMOS process. Quasi-1D resonators in lateral p-i-n structures allow for resonant defect-state photodetection in all-silicon devices, exhibiting voltage-dependent quantum efficiencies in the range of a few 10 s of %, few-GHz bandwidths, and low dark currents, in devices with loaded Qs in the range of 4,300-9,300 one device, for example, exhibited a loaded Q of 4,300, 25% quantum efficiency (corresponding to a responsivity of 0.31 A/W), 3 GHz bandwidth, and 30 nA dark current at a reverse bias of 30 V. This work demonstrates the possibility for practical integration of PhC microresonators with active electro-optic capability into large-scale silicon photonic systems.

  9. Photonic Crystal Structures with Tunable Structure Color as Colorimetric Sensors

    PubMed Central

    Wang, Hui; Zhang, Ke-Qin

    2013-01-01

    Colorimetric sensing, which transduces environmental changes into visible color changes, provides a simple yet powerful detection mechanism that is well-suited to the development of low-cost and low-power sensors. A new approach in colorimetric sensing exploits the structural color of photonic crystals (PCs) to create environmentally-influenced color-changeable materials. PCs are composed of periodic dielectrics or metallo-dielectric nanostructures that affect the propagation of electromagnetic waves (EM) by defining the allowed and forbidden photonic bands. Simultaneously, an amazing variety of naturally occurring biological systems exhibit iridescent color due to the presence of PC structures throughout multi-dimensional space. In particular, some kinds of the structural colors in living organisms can be reversibly changed in reaction to external stimuli. Based on the lessons learned from natural photonic structures, some specific examples of PCs-based colorimetric sensors are presented in detail to demonstrate their unprecedented potential in practical applications, such as the detections of temperature, pH, ionic species, solvents, vapor, humidity, pressure and biomolecules. The combination of the nanofabrication technique, useful design methodologies inspired by biological systems and colorimetric sensing will lead to substantial developments in low-cost, miniaturized and widely deployable optical sensors. PMID:23539027

  10. Optical study of Sb-S-I glass photonic crystals

    NASA Astrophysics Data System (ADS)

    Starczewska, Anna; Kępińska, Mirosława; Nowak, Marian; Szperlich, Piotr

    2015-12-01

    This work is focused on optical investigations of Sb-S-I glass photonic crystals based on three-dimensional opal template with a closed-packed face centered cubic (fcc) lattice prepared from monodisperse silicon (SiO2) spheres by gravity sedimentation. Three types of photonic structures have been examined: SiO2-opals, opals filled with Sb-S-I glass (direct opals) and Sb-S-I inverted opals obtained after removing SiO2 templates. Optical properties have been investigated by reflectance spectroscopy for wavelengths from 250 nm to 1100 nm. These measurements exhibit Bragg's peaks connected with photonic band gap that is tunable in position and width by varying the diameter of spheres and medium filling the opal. Values of the real parts of refractive index of the Sb-S-I in the fabricated inverted opals nmed[λ ∈ (850-950) nm] = 2.42 ± 0.08 and nmed[λ ∈ (675-750) nm] = 2.39 ± 0.11 have been determined.

  11. Nanostructured Surfaces and Detection Instrumentation for Photonic Crystal Enhanced Fluorescence

    PubMed Central

    Chaudhery, Vikram; George, Sherine; Lu, Meng; Pokhriyal, Anusha; Cunningham, Brian T.

    2013-01-01

    Photonic crystal (PC) surfaces have been demonstrated as a compelling platform for improving the sensitivity of surface-based fluorescent assays used in disease diagnostics and life science research. PCs can be engineered to support optical resonances at specific wavelengths at which strong electromagnetic fields are utilized to enhance the intensity of surface-bound fluorophore excitation. Meanwhile, the leaky resonant modes of PCs can be used to direct emitted photons within a narrow range of angles for more efficient collection by a fluorescence detection system. The multiplicative effects of enhanced excitation combined with enhanced photon extraction combine to provide improved signal-to-noise ratios for detection of fluorescent emitters, which in turn can be used to reduce the limits of detection of low concentration analytes, such as disease biomarker proteins. Fabrication of PCs using inexpensive manufacturing methods and materials that include replica molding on plastic, nano-imprint lithography on quartz substrates result in devices that are practical for single-use disposable applications. In this review, we will describe the motivation for implementing high-sensitivity fluorescence detection in the context of molecular diagnosis and gene expression analysis though the use of PC surfaces. Recent efforts to improve the design and fabrication of PCs and their associated detection instrumentation are summarized, including the use of PCs coupled with Fabry-Perot cavities and external cavity lasers. PMID:23624689

  12. Experimental GVD engineering in slow light slot photonic crystal waveguides

    NASA Astrophysics Data System (ADS)

    Serna, Samuel; Colman, Pierre; Zhang, Weiwei; Le Roux, Xavier; Caer, Charles; Vivien, Laurent; Cassan, Eric

    2016-05-01

    The use in silicon photonics of the new optical materials developed in soft matter science (e.g. polymers, liquids) is delicate because their low refractive index weakens the confinement of light and prevents an efficient control of the dispersion properties through the geometry. We experimentally demonstrate that such materials can be incorporated in 700 μm long slot photonic crystal waveguides, and hence can benefit from both slow-light field enhancement effect and slot-induced ultra-small effective areas. Additionally, we show that their dispersion can be engineered from anomalous to normal regions, along with the presence of multiple zero group velocity dispersion (ZGVD) points exhibiting Normalized Delay Bandwidth Product as high as 0.156. The reported results provide experimental evidence for an accurate control of the dispersion properties of fillable periodical slotted structures in silicon photonics, which is of direct interest for on-chip all-optical data treatment using nonlinear optical effects in hybrid-on-silicon technologies.

  13. Observation of soliton compression in silicon photonic crystals

    PubMed Central

    Blanco-Redondo, A.; Husko, C.; Eades, D.; Zhang, Y.; Li, J.; Krauss, T.F.; Eggleton, B.J.

    2014-01-01

    Solitons are nonlinear waves present in diverse physical systems including plasmas, water surfaces and optics. In silicon, the presence of two photon absorption and accompanying free carriers strongly perturb the canonical dynamics of optical solitons. Here we report the first experimental demonstration of soliton-effect pulse compression of picosecond pulses in silicon, despite two photon absorption and free carriers. Here we achieve compression of 3.7 ps pulses to 1.6 ps with <10 pJ energy. We demonstrate a ~1-ps free-carrier-induced pulse acceleration and show that picosecond input pulses are critical to these observations. These experiments are enabled by a dispersion-engineered slow-light photonic crystal waveguide and an ultra-sensitive frequency-resolved electrical gating technique to detect the ultralow energies in the nanostructured device. Strong agreement with a nonlinear Schrödinger model confirms the measurements. These results further our understanding of nonlinear waves in silicon and open the way to soliton-based functionalities in complementary metal-oxide-semiconductor-compatible platforms. PMID:24423977

  14. A thermally tunable inverse opal photonic crystal for monitoring glass transition.

    PubMed

    Sun, Liguo; Xie, Zhuoying; Xu, Hua; Xu, Ming; Han, Guozhi; Wang, Cheng; Bai, Xuduo; Gu, ZhongZe

    2012-03-01

    An optical method was developed to monitor the glass transition of the polymer by taking advantage of reflection spectrum change of the thermally tunable inverse opal photonic crystal. The thermally tunable photonic bands of the polymer inverse opal photonic crystal were traceable to the segmental motion of macromolecules, and the segmental motion was temperature dependent. By observing the reflection spectrum change of the polystyrene inverse opal photonic crystal during thermal treatment, the glass transition temperature of polystyrene was gotten. Both changes of the position and intensity of the reflection peak were observed during the glass transition process of the polystyrene inverse opal photonic crystal. The optical change of inverse opal photonic crystal was so large that the glass transition temperature could even be estimated by naked eyes. The glass transition temperature derived from this method was consistent with the values measured by differential scanning calorimeter.

  15. Photonic drop splitters based on silicon photonic crystal cascaded self-collimation ring resonators

    NASA Astrophysics Data System (ADS)

    Lin, Yuan-Yuan; Chen, Xi-Yao; Jiang, Jun-Zhen; Fu, Ping; Chen, Biao; Yang, Li-Hui; Liu, Jing-Ping; Lin, Bao-Cheng

    2014-10-01

    In this paper, the 1×5 optical splitters (OSs) based on 2D rod-type silicon photonic crystal embed cascaded self-collimation (SC) ring resonators (CSCRR) was proposed. The 1×5 OSs consist of eight beam splitters, which are formed by varying the radii of the rod. With self-collimation effect, we can manipulate the light's propagation in the OSs. Here we consider TM modes. Utilizing multiple-beam interference theory, the theoretical transmission spectra at different outputs were analysed. These transmission spectra can help us to set the radii of eight slitters properly, for we can control the light coming out from five ports with the light-intensity ratio we need. Meanwhile these outputs' transmission spectra were investigated by the finite-difference time-domain (FDTD) method. The simulative results have an agreement with the theoretical prediction. The 1×5 OSs will have practical applications in photonic integrated circuits.

  16. Photonic states deep into the waveguide cutoff frequency of metallic mesh photonic crystal filters

    NASA Astrophysics Data System (ADS)

    Sang, Hong-Yi; Li, Zhi-Yuan; Gu, Ben-Yuan

    2005-02-01

    We examine the optical properties of three-dimensional metallic photonic crystals made from a periodic stacking of thin metallic mesh layers separated by homogeneous dielectric films by means of a combination of the plane-wave-based transfer-matrix method and analytical modal solution approach. Although each metallic mesh layer can serve as a frequency-selective surface and involves an intrinsic long-wavelength waveguide cutoff to electromagnetic waves, pass bands and new band gaps can exist far below the cutoff frequency due to the global coupling effect among different mesh layers. The results for the transmission spectra and photonic band structures are in good agreement with existing experimental measurements. It is found that the position of the pass bands and band gaps strongly depends on the thickness and composite of the separation layer between the adjacent metallic mesh layers.

  17. The Photonic Band Gaps in the Two-Dimensional Plasma Photonic Crystals with Rhombus Lattice

    NASA Astrophysics Data System (ADS)

    Zhang, Kaiming; Sun, Dongsheng

    2016-06-01

    In this paper, under two different electromagnetic modes, the photonic band gaps (PBGs) in the two-dimensional plasma photonic crystals (PPCs) are theoretically investigated based on the plane wave expansion method. The proposed PPCs are arranged in rhombus lattices, in which the homogeneous unmagnetized plasma rods are immersed in the isotropic dielectric background. The computed results showed that PBGs can be easily tuned by the angle of rhombus lattices, and a cutoff frequency and a flatbands region can be observed under the TM and TE polarized waves, respectively. The relationships between the relative bandwidths of first PBGs and the parameters of PPCs in two such cases also are discussed. The numerical simulations showed that the PBGs can be manipulated obviously by the parameters as mentioned above. The proposed results can be used to design the waveguide and filter based on the PPCs.

  18. Photonic nanojet focusing for hollow-core photonic crystal fiber probes.

    PubMed

    Ghenuche, Petru; Rigneault, Hervé; Wenger, Jérôme

    2012-12-20

    Large-pitch kagome-lattice hollow-core photonic crystal fibers (HC-PCFs) offer appealing optical properties for beam delivery and remote sensing. However, focusing their optical mode on a submicrometer spot can be challenging due to the large mode diameter and low numerical aperture of these fibers. Here, we demonstrate that a 30 μm latex microsphere directly set at the HC-PCF end-face provides an efficient means to focus the fiber mode down to a spot of 540 nm full width at half-maximum thanks to a photonic nanojet effect. The system is used for fluorescence imaging and direct laser writing on a thin absorbing layer. Potential applications include inspection of semiconductor wafers, photolithography, laser surgery, fluorescence sensing, or optical transfection.

  19. Nonaqueous sol-gel chemistry applied to atomic layer deposition: tuning of photonic band gap properties of silica opals.

    PubMed

    Marichy, Catherine; Dechézelles, Jean-Francois; Willinger, Marc-Georg; Pinna, Nicola; Ravaine, Serge; Vallée, Renaud

    2010-05-01

    Combining both electromagnetic simulations and experiments, it is shown that the photonic pseudo band gap (PPBG) exhibited by a silica opal can be fully controlled by Atomic Layer Deposition (ALD) of titania into the pores of the silica spheres constituting the opal. Different types of opals were assembled by the Langmuir-Blodgett technique: homogeneous closed packed structures set up of, respectively, 260 and 285 nm silica spheres, as well as opal heterostructures consisting of a monolayer of 430 nm silica spheres embedded within 10 layers of 280 nm silica spheres. For the stepwise infiltration of the opals with titania, titanium isopropoxide and acetic acid were used as metal and oxygen sources, in accordance with a recently published non-aqueous approach to ALD. A shift of the direct PPBG, its disappearance, and the subsequent appearance and shifting of the inverse PPBG are observed as the opal is progressively filled. The close agreement between simulated and experimental results is striking, and promising in terms of predicting the properties of advanced photonic materials. Moreover, this work demonstrates that the ALD process is rather robust and can be applied to the coating of complex nanostructures.

  20. Helium irradiation effects in polycrystalline Si, silica, and single crystal Si

    SciTech Connect

    Abrams, K. J.; Greaves, G.; Berg, J. A. van den; Hinks, J. A.; Donnelly, S. E.; Pawley, C. J.; Eyidi, D.; Ward, M. B.

    2012-04-15

    Transmission electron microscopy (TEM) has been used to investigate the effects of room temperature 6 keV helium ion irradiation of a thin ({approx_equal}55 nm thick) tri-layer consisting of polycrystalline Si, silica, and single-crystal Si. The ion irradiation was carried out in situ within the TEM under conditions where approximately 24% of the incident ions came to rest in the specimen. This paper reports on the comparative development of irradiation-induced defects (primarily helium bubbles) in the polycrystalline Si and single-crystal Si under ion irradiation and provides direct measurement of a radiation-induced increase in the width of the polycrystalline layer and shrinkage of the silica layer. Analysis using TEM and electron energy-loss spectroscopy has led to the hypothesis that these result from helium-bubble-induced swelling of the silicon and radiation-induced viscoelastic flow processes in the silica under the influence of stresses applied by the swollen Si layers. The silicon and silica layers are sputtered as a result of the helium ion irradiation; however, this is estimated to be a relatively minor effect with swelling and stress-related viscoelastic flow being the dominant mechanisms of dimensional change.

  1. Ultrathin silica films: the atomic structure of two-dimensional crystals and glasses.

    PubMed

    Büchner, Christin; Lichtenstein, Leonid; Yu, Xin; Boscoboinik, J Anibal; Yang, Bing; Kaden, William E; Heyde, Markus; Shaikhutdinov, Shamil K; Włodarczyk, Radosław; Sierka, Marek; Sauer, Joachim; Freund, Hans-Joachim

    2014-07-21

    For the last 15 years, we have been studying the preparation and characterization of ordered silica films on metal supports. We review the efforts so far, and then discuss the specific case of a silica bilayer, which exists in a crystalline and a vitreous variety, and puts us into a position to investigate, for the first time, the real space structure (AFM/STM) of a two-dimensional glass and its properties. We show that pair correlation functions determined from the images of this two-dimensional glass are similar to those determined by X-ray and neutron scattering from three-dimensional glasses, if the appropriate sensitivity factors are taken into account. We are in a position, to verify, for the first time, a model of the vitreous silica structure proposed by William Zachariasen in 1932. Beyond this, the possibility to prepare the crystalline and the glassy structure on the same support allows us to study the crystal-glass phase transition in real space. We, finally, discuss possibilities to use silica films to start investigating related systems such as zeolites and clay films. We also mention hydroxylation of the silica films in order to adsorb metal atoms modeling heterogenized homogeneous catalysts. PMID:24990633

  2. Photochemical switching behavior of azofunctionalized polymer liquid crystal/SiO{sub 2} composite photonic crystal

    SciTech Connect

    Moritsugu, M.; Kim, S. N.; Ogata, T.; Nonaka, T.; Kurihara, S.; Kubo, S.; Segawa, H.; Sato, O.

    2006-10-09

    A photochemically tunable photonic crystal was prepared by infiltrating azopolymer liquid crystal in a SiO{sub 2} inverse opal structure. The SiO{sub 2} inverse opal film obtained reflected a light corresponding to the periodicity as well as the refractive indices of the inverse opal structure. Linearly polarized light irradiation shifted the reflection band to longer wavelength more than 15 nm. This is caused by the formation of anisotropic molecular orientation of the azopolymer. The switched state was stable in the dark, and the reversible switching of the reflection band can be achieved by the linearly and circularly polarized light irradiations.

  3. Magnetic-field tunable defect modes in a photonic-crystal/liquid-crystal cell.

    PubMed

    Zyryanov, Victor Ya; Myslivets, Sergey A; Gunyakov, Vladimir A; Parshin, Alexander M; Arkhipkin, Vasily G; Shabanov, Vasily F; Lee, Wei

    2010-01-18

    Light transmission spectrum of a multilayer photonic crystal with a central liquid-crystal defect layer placed between crossed polarizers has been studied. Transmittance was varied due to the magnetically induced reorientation of the nematic director from homeotropic to planar alignment. Two notable effects were observed for this scheme: the spectral shift of defect modes corresponding to the extraordinary light wave and its superposition with the ordinary one. As a result, the optical cell allows controlling the intensity of interfering defect modes by applied magnetic field. PMID:20173953

  4. A nano-patterned photonic crystal laser with a dye-doped liquid crystal

    NASA Astrophysics Data System (ADS)

    Ko, Doo-Hyun; Morris, Stephen M.; Lorenz, Alexander; Castles, Flynn; Butt, Haider; Gardiner, Damian J.; Qasim, Malik M.; Wallikewitz, Bodo; Hands, Philip J. W.; Wilkinson, Timothy D.; Amaratunga, Gehan A. J.; Coles, Harry J.; Friend, Richard H.

    2013-07-01

    Covering a nano-patterned titanium dioxide photonic crystal (PC) within a well-oriented film of dye-doped liquid crystal (LC), a distributed feedback laser is constructed whereby the emission characteristics can be manipulated in-situ using an electric field. This hybrid organic-inorganic structure permits simultaneous selectivity of both the beam pattern and laser wavelength by electrical addressing of the LC director. In addition, laser emission is obtained both in the plane and normal to the PC. Along with experimental data, a theoretical model is presented that is based upon an approximate calculation of the band structure of this birefringent, tuneable laser device.

  5. Photonic crystal fibre enables short-wavelength two-photon laser scanning fluorescence microscopy with fura-2

    NASA Astrophysics Data System (ADS)

    McConnell, Gail; Riis, Erling

    2004-10-01

    We report on a novel and compact reliable laser source capable of short-wavelength two-photon laser scanning fluorescence microscopy based on soliton self-frequency shift effects in photonic crystal fibre. We demonstrate the function of the system by performing two-photon microscopy of smooth muscle cells and cardiac myocytes from the rat pulmonary vein and Chinese hamster ovary cells loaded with the fluorescent calcium indicator fura-2/AM.

  6. Microwave assisted N-alkylation of amine functionalized crystal-like mesoporous phenylene-silica.

    PubMed

    Lourenço, Mirtha A O; Siegel, Renée; Mafra, Luís; Ferreira, Paula

    2013-04-28

    N-alkylation reaction of amine functionalized phenylene moieties in crystal-like mesoporous silica is successfully achieved with about 87% of conversion in two reaction cycles. A potassium iodide catalyzed method commonly used for the selective N-monoalkylation of aniline is adapted and optimized to the N-monoalkylation reactions of the amine functionalized periodic mesoporous phenylene-silica (NH2-PMO) under microwave irradiation with preservation of the ordered mesostructure and of the crystal-like molecular scale periodicity of the material. This functionalization opens an avenue for the preparation of new materials with different amino-alkyl groups specially designed for a desired application, namely on the adsorption or catalytic fields.

  7. Crystallization of Carbamazepine in Proximity to Its Precursor Iminostilbene and a Silica Surface

    PubMed Central

    2016-01-01

    Amorphous films of the anticonvulsant drug carbamazepine are easily accessible by various methods, while the crystallization into specific polymorphs represents a challenging and time-consuming task. In this work, the crystallization of drop cast carbamazepine at silica surfaces is investigated by atomic force microscopy and both in situ and ex situ grazing incidence X-ray diffraction. The pristine films grow with low crystallization rates into a triclinic polymorph, exhibiting poor orientational order within films. However, if iminostilbene, a chemical precursor of carbamazepine, is added to the solution, enhanced crystallization rates result. The individual components crystallize phase-separated upon solvent evaporation without the formation of cocrystals. Iminostilbene reduces the time scale of carbamazepine crystallization from several hours to minutes. Besides the change in crystallization dynamics, iminostilbene induces order to the carbamazepine crystallites, evident as a 110 texture. In situ data of intermixed solutions demonstrate that iminostilbene crystallization occurs first. The iminostilbene crystals then act as templates for carbamazepine growth, whereby fully epitaxial growth is suggested from the results. The findings motivate such an approach for other systems, as this solution-processed, intrinsic epitaxial behavior might be employed in up-scaled manufacturing processes. PMID:27175105

  8. One-dimensional photonic crystals containing memory-enabling liquid-crystal defect layers

    NASA Astrophysics Data System (ADS)

    Wu, Po-Chang; Lee, Wei

    2013-09-01

    Incorporating liquid crystal (LC) as a defect layer in a photonic crystal (PC) leads to the electrically tunable optical spectrum in defect modes within the photonic band gap. While the LC defect layer has bi- or multi-stable states, the profile of defect modes in each stable state can be preserved permanently without applied voltage, indicating a feature of low power consumption for photonic applications. In this paper, we report on our recent development of optical and spectral properties of multilayer PC structures containing various types of memory-enabling LC (ME-LC), including a bistable chiral-tilted homeotropic nematic (BHN), a bistable chiral-splay nematic (BCSN), a bistable dual-frequency cholesteric LC (DFCLC), a tristable polymer-stabilized cholesteric texture (PSCT), and a tristable smectic-A liquid crystal as a defect layer. The defect modes of the PC/ME-LC cell can be switched to not only the voltage-sustained states but the memory states. As a result, PC/ME-LC cells reveal several features such as the wavelength tunability, transmission tunability and optical bistability or tristability of defect modes that are of potential for realizing tunable and memorable optical devices such as low-power-consumption multichannel filters, light shutters or electrically controllable intensity modulators with green concept.

  9. Nonlinear optics in high refractive index contrast photonic crystal microcavities

    NASA Astrophysics Data System (ADS)

    Cowan, Allan Ralph

    2005-07-01

    This thesis describes theoretical and experimental research on the nonlinear response of high refractive index contrast (HRIC) optical microcavities. An intuitive, numerically efficient model of second harmonic reflection from two dimensional (2D), planar photonic crystals made of sub-wavelength thick, non-centrosymmetric semiconductors is developed. It predicts that appropriate 2D texture can result in orders of magnitude enhancement of the reflected second order signal when harmonic plane waves are used to excite leaky photonic crystal eigenmodes. Local field enhancement in the textured slab, and other physical processes responsible for these enhancements are explained. A different formalism is developed to treat the Kerr-related bistable response of a 3D microcavity coupled to a single mode waveguide. This model predicts that optical bistability should be observed using only milliwatts of power to excite a cavity fabricated in Al0.18 Ga0.82As, having a quality factor of Q = 4000 and a mode volume of 0.05 mum 3. Two-photon absorption is shown to only slightly hinder the performance in Al0.18Ga0.82 As. By including nonresonant downstream reflections in the model, novel hysteresis loops are predicted, and their stability is analyzed. A coupled waveguide-microcavity structure is fabricated by selectively cladding a silicon ridge-Bragg grating waveguide with photoresist. Three-dimensionally localized optical modes are realized with Q values ranging from 200 to 1200, at ˜1.5 mum. Using 100 fs pulses, the transmission spectra of these structures is studied as a function of input power. The output power saturates when the cavity mode and pulse centre frequencies are resonant, and the output exhibits superlinear growth when they are appropriately detuned. These results are explained in terms of the filtering action of the microcavity on the nonlinear spectral distortion of the input pulse as it propagates through the waveguide. PbSe nanocrystals are deposited on a

  10. Extraordinary wavelength reduction in terahertz graphene-cladded photonic crystal slabs

    PubMed Central

    Williamson, Ian A. D.; Mousavi, S. Hossein; Wang, Zheng

    2016-01-01

    Photonic crystal slabs have been widely used in nanophotonics for light confinement, dispersion engineering, nonlinearity enhancement, and other unusual effects arising from their structural periodicity. Sub-micron device sizes and mode volumes are routine for silicon-based photonic crystal slabs, however spectrally they are limited to operate in the near infrared. Here, we show that two single-layer graphene sheets allow silicon photonic crystal slabs with submicron periodicity to operate in the terahertz regime, with an extreme 100× wavelength reduction from graphene’s large kinetic inductance. The atomically thin graphene further leads to excellent out-of-plane confinement, and consequently photonic-crystal-slab band structures that closely resemble those of ideal two-dimensional photonic crystals, with broad band gaps even when the slab thickness approaches zero. The overall photonic band structure not only scales with the graphene Fermi level, but more importantly scales to lower frequencies with reduced slab thickness. Just like ideal 2D photonic crystals, graphene-cladded photonic crystal slabs confine light along line defects, forming waveguides with the propagation lengths on the order of tens of lattice constants. The proposed structure opens up the possibility to dramatically reduce the size of terahertz photonic systems by orders of magnitude. PMID:27143314

  11. Optical properties of photonic crystal fiber with integral micron-sized Ge wire.

    PubMed

    Tyagi, H K; Schmidt, M A; Prill Sempere, L; Russell, P St J

    2008-10-27

    Using a selective hole closure technique, individual hollow channels in silica-air photonic crystal fibers are filled with pure Ge by pumping in molten material at high pressure. The smallest channels filled so far are 600 nm in diameter, which is 10x smaller than in previous work. Electrical conductivity and micro-Raman measurements indicate that the resulting cm-long wires have a high degree of crystallinity. Optical transmission spectra are measured in a sample with a single wire placed adjacent to the core of an endlessly single-mode photonic crystal fiber. This renders the fiber birefringent, as well as causing strongly polarization-dependent transmission losses, with extinction ratios as high as 30 dB in the visible. In the IR, anti-crossings between the glass-core mode and resonances on the high index Ge wire create a series of clear dips in the spectrum transmitted through the fiber. The measurements agree closely with the results of finite-element simulations in which the wavelength dependence of the dielectric constants is taken fully into account. A toy model based on a multilayer structure is used to help interpret the results. Finally, the temperature dependence of the anti-crossing wavelengths is measured, the preliminary results suggesting that the structure might form the basis of a compact optical thermometer. Since Ge provides electrical conductance together with low-loss guidance in the mid-IR, Ge-filled PCF seems likely to lead to new kinds of in-fiber detector and sensor, as well as having potential uses in ultra-low-threshold nonlinear optical devices.

  12. Fabrication of flexible photonic crystal using alumina ball inserted Teflon tube

    NASA Astrophysics Data System (ADS)

    Watanabe, Yoshimi; Hotta, Takehiro; Sato, Hisashi

    2010-09-01

    In our previous paper, it was found that cotton yarn/TiO2-dispersed resin photonic crystals were fabricated successfully by applying textile technology. However, it is difficult to apply for practical use because these photonic crystals cannot change their shape flexibly. In this study, we fabricate the flexible photonic crystals using high-dielectric constant fibers. The high-dielectric constant fibers were made by inserting alumina balls into Teflon tubes. The crossed linear-fiber laminated fabric and multilayered woven fabric with an fcc lattice structure were structured by aligning high-dielectric constant fibers periodically. These photonic crystals consist of air and high-dielectric constant fibers. The attenuation of transmission amplitude through the photonic crystals was measured. The photonic crystal of crossed linear-fiber laminated fabric exhibits a forbidden gap in the range from 16 to 18 GHz range. On the other hand, the photonic crystal of multilayered woven fabric, which was fabricated by the same parameter with crossed linear-fiber laminated fabric, also exhibits a forbidden gap in the range from 13 to 16 GHz range. Thus, we can successfully fabricate flexible photonic crystals of woven fabric using high-dielectric constant fibers.

  13. Experimental studies of polarization properties of supercontinua generated in a birefringent photonic crystal fiber.

    PubMed

    Zhu, Zhaoming; Brown, Thomas

    2004-03-01

    Besides coherence degradations, supercontinuum spectra generated in birefringent photonic crystal fibers also suffer from polarization fluctuations because of noise in the input pump pulse. This paper describes an experimental study of polarization properties of supercontinuum spectra generated in a birefringent photonic crystal fiber, validating previous numerical simulations. PMID:19474887

  14. Self-energy shift of the energy levels of atomic hydrogen in photonic crystal medium

    NASA Astrophysics Data System (ADS)

    Gainutdinov, R. Kh; Khamadeev, M. A.; Steryakov, O. V.; Ziyatdinova, K. A.; Salakhov, M. Kh

    2016-05-01

    Corrections to the average kinetic energy of atomic electrons caused by the change in electron mass in the photonic crystal medium are investigated. Corresponding shift of energy levels of atoms placed in a photonic crystal is shown to be of order of the ordinary Lamb shift.

  15. Polarization beam splitters based on a two-dimensional photonic crystal of negative refraction.

    PubMed

    Ao, Xianyu; He, Sailing

    2005-08-15

    A two-dimensional metallo-dielectric photonic crystal of negative refraction was designed for the application of polarization beam splitters. To match the refractive index of air, the effective refractive index of the designed photonic crystal is -1 for TE polarization and +1 for TM polarization. Two types of polarization beam splitter are presented. PMID:16127940

  16. Transfer of Preformed Three-Dimensional Photonic Crystals onto Dye-Sensitized Solar Cells

    SciTech Connect

    Mihi, Agustín; Zhang, Chunjie; Braun, Paul V.

    2011-05-09

    Preformed self-assembled 3D photonic crystals can be infilled with a polycarbonate matrix for mechanical stability and transferred onto rough and porous optoelectronic and photovoltaic devices. This technique allows the incorporation of photonic crystals onto independently processed devices, in which the transferred films have high optical quality.

  17. Parametric down-conversion with optimized spectral properties in nonlinear photonic crystals

    SciTech Connect

    Corona, Maria; U'Ren, Alfred B.

    2007-10-15

    We study the joint spectral properties of photon pairs generated by spontaneous parametric down-conversion in a one-dimensional nonlinear photonic crystal in a collinear, degenerate, type-II geometry. We show that the photonic crystal properties may be exploited to compensate for material dispersion and obtain photon pairs that are nearly factorable, in principle, for arbitrary materials and spectral regions, limited by the ability to fabricate the nonlinear crystal with the required periodic variation in the refractive indices for the ordinary and extraordinary waves.

  18. Absorption effects on the Mie plasmon-polariton modes in two-dimensional plasmonic photonic crystals

    NASA Astrophysics Data System (ADS)

    Diaz-Valencia, B. F.; Mejía-Salazar, J. R.; Porras-Montenegro, N.

    2015-09-01

    We have theoretically investigated the absorption effects on the Mie plasmonic resonances in single metallic shell rods and two-dimensional plasmonic photonic crystals. Present results show that Mie resonances stemming from the dipolar and quadrupolar contributions are robust to absorption effects not only in single scatterers but also in the case of two-dimensional plasmonic photonic crystals. On the other hand, we have found that the extinction (Qext) and scattering (Qsca) efficiencies corresponding to an isolated metallic rod may be employed to predict the frequency range for flat or slow dispersive photonic bands in plasmonic photonic crystals, indicating a robust behavior of such resonant modes.

  19. Analysis of plasma-magnetic photonic crystal with a tunable band gap

    SciTech Connect

    Mehdian, H.; Mohammadzahery, Z.; Hasanbeigi, A.

    2013-04-15

    In this paper, electromagnetic wave propagation through the one-dimensional plasma-magnetic photonic crystal in the presence of external magnetic field has been analyzed. The dispersion relation, transmission and reflection coefficients have been obtained by using the transfer matrix method. It is investigated how photonic band gap of photonic crystals will be tuned when both dielectric function {epsilon} and magnetic permeability {mu} of the constitutive materials, depend on applied magnetic field. This is shown by one dimensional photonic crystals consisting of plasma and ferrite material layers stacked alternately.

  20. Genetically designed L3 photonic crystal nanocavities with measured quality factor exceeding one million

    SciTech Connect

    Lai, Y.; Badolato, A.; Pirotta, S.; Urbinati, G.; Gerace, D.; Galli, M.; Minkov, M.; Savona, V.

    2014-06-16

    We report on the experimental realization of ultra-high quality factor (Q) designs of the L3-type photonic crystal nanocavity. Based on genetic optimization of the positions of few nearby holes, our design drastically improves the performance of the conventional L3 as experimentally confirmed by direct measurement of Q ≃ 2 × 10{sup 6} in a silicon-based photonic crystal membrane. Our devices rank among the highest Q/V ratios ever reported in photonic crystal cavities, holding great promise for the realization of integrated photonic platforms based on ultra-high-Q resonators.