Optical design of low cost imaging systems for mobile medical applications

NASA Astrophysics Data System (ADS)

Kass, Alexander; Slyper, Ronit; Levitz, David

2015-03-01

Colposcopes, the gold standard devices for imaging the cervix at high magnfication, are expensive and sparse in low resource settings. Using a lens attachment, any smartphone camera can be turned into an imaging device for tissues such as the cervix. We create a smartphone-based colposcope using a simple lens design for high magnification. This particular design is useful because it allows parameters such as F-number, depth of field, and magnification to be controlled easily. We were therefore able to determine a set of design steps which are general to mobile medical imaging devices and allow them to maintain requisite image quality while still being rugged and affordable.

Very-Low-Cost, Rugged Vacuum System

NASA Technical Reports Server (NTRS)

Kline-Schoder, Robert; Sorensen, Paul; Passow, Christian; Bilski, Steve

2013-01-01

NASA, DoD, DHS, and commercial industry have a need for miniaturized, rugged, low-cost vacuum systems. Recent advances in sensor technology have led to the development of very small mass spectrometer detectors as well as other miniature analytical instruments. However, the vacuum systems to support these sensors remain large, heavy, and power-hungry. To meet this need, a miniaturized vacuum system was created based on a very small, rugged, and inexpensive- to-manufacture molecular drag pump (MDP). The MDP is enabled by the development of a miniature, veryhigh- speed, rugged, low-power, brushless DC motor optimized for wide temperature operation and long life. Such a pump represents an order-of-magnitude reduction in mass, volume, and cost over current, commercially available, state-ofthe- art vacuum pumps. The vacuum system consists of the MDP coupled to a ruggedized rough pump (for terrestrial applications or for planets with substantial atmospheres). The rotor in the MDP consists of a simple smooth cylinder of aluminum spinning at approximately 200,000 RPM inside an outer stator housing. The pump stator comprises a cylindrical aluminum housing with one or more specially designed grooves that serve as flow channels. To minimize the length of the pump, the gas is forced down the flow channels of the outer stator to the base of the pump. The gas is then turned and pulled toward the top through a second set of channels cut into an inner stator housing that surrounds the motor. The compressed gas then flows down channels in the motor housing to the exhaust port of the pump. The exhaust port of the pump is connected to a diaphragm or scroll pump. This pump delivers very high performance in a very small envelope. The design was simplified so that a smaller compression ratio, easier manufacturing process, and enhanced ruggedness can be achieved at the lowest possible cost. The machining of the rotor and stators is very simple compared to that necessary to fabricate TMP (turbo molecular pump) rotor and stator blades. Also, the symmetry of the rotor is such that dynamic balancing of the rotor is greatly simplified. Finally, because of the simplified design, the number of parts in the unit is cut by nearly a factor of three. In fact, there are only five parts, not counting the motor and off-the-shelf screws and O-rings. This reduces the amount of machining and also makes fit-up much simpler while allowing the maintenance of close tolerances.

A New Paradigm for Robotic Rovers

NASA Astrophysics Data System (ADS)

Clark, P. E.; Curtis, S. A.; Rilee, M. L.

We are in the process of developing rovers with extreme mobility needed to explore remote, rugged terrain. We call these systems Tetrahedral Explorer Technologies (TETs). Architecture is based on conformable tetrahedra, the simplest space-filling form, as building blocks, single or networked, where apices act as nodes from which struts reversibly deploy. The tetrahedral framework acts as a simple skeletal muscular structure. We have already prototyped a simple robotic walker from a single reconfigurable tetrahedron capable of tumbling and a more evolved 12Tetrahedral Walker, the Autonomous Landed Investigator (ALI), which has interior nodes for payload, more continuous motion, and is commandable through a user friendly interface. ALI is an EMS level mission concept which would allow autonomous in situ exploration of the lunar poles within the next decade. ALI would consist of one or more 12tetrahedral walkers capable of rapid locomotion with the many degrees of freedom and equipped for navigation in the unilluminated, inaccessible and thus largely unexplored rugged terrains where lunar resources are likely to be found: the Polar Regions. ALI walkers would act as roving reconnaissance teams for unexplored regions, analyzing samples along the way.

Application of a simple column-switching ion chromatography technique for removal of matrix interferences and sensitive fluorescence determination of acidic compounds (pharmaceutical drugs) in complex samples.

PubMed

Muhammad, Nadeem; Subhani, Qamar; Wang, Fenglian; Guo, Dandan; Zhao, Qiming; Wu, Shuchao; Zhu, Yan

2017-09-15

This work illustrates the introduction of a simple, rugged and flexible column-switching ion chromatography (IC) technique for an automated on-line QuEChERS extracted samples extracts washing followed by sensitive fluorescence (FLD) determination of five acidic pharmaceutical drugs namely; clofibric acid (CLO), ibuprofen (IBU), aspirin (ASP), naproxen (NAP) and flurobrofen (FLU) in three complex samples (spinach, apple and hospital sewage sludge). An old anion exchange column IonPac ® AS11-HC was utilized as a pre-treatment column for on-line washing of inorganic and organic interferences followed by isocratic separation of five acidic drugs with another anion exchange IonPac ® AS12A analytical column by exploiting the column-switching technique. This novel method exhibited good linearity with correlation coefficients (r 2 ) for all drugs were in the range 0.976-0.996. The limit of detection and quantification of all five acidic drugs were in the range 0.024μg/kg to 8.70μg/kg and 0.082μg/kg to 0.029mg/kg, respectively, and better recoveries in the range 81.17-112.5% with percentage relative standard deviations (RSDs) less than 17.8% were obtained. This on-line sample pre-treatment method showed minimum matrix effect in the range of 0.87-1.25 except for aspirin. This simple rugged and flexible column-switching system required only 28min for maximum elimination of matrices and interferences in three complex samples extracts, isocratic separation of five acidic drugs and for the continuous regeneration of pre-treatment column prior to every subsequent analysis. Finally, this simple automated IC system was appeared so rugged and flexible, which can eliminate and wash out most of interference, impurities and matrices in complex samples, simply by adjusting the NaOH and acetonitrile concentration in washing mobile phase with maximum recoveries of acidic analytes of interest. Copyright © 2017. Published by Elsevier B.V.

Development of high-performance low-reflection rugged resistive touch screens for military displays

NASA Astrophysics Data System (ADS)

Wang, Raymond; Wang, Minshine; Thomas, John; Wang, Lawrence; Chang, Victor

2010-04-01

Just as iPhones with sophisticated touch interfaces have revolutionised the human interface for the ubiquitous cell phone, the Military is rapidly adopting touch-screens as a primary interface to their computers and vehicle systems. This paper describes the development of a true military touch interface solution from an existing industrial design. We will report on successful development of 10.4" and 15.4" high performance rugged resistive touch panels using IAD sputter coating. Low reflectance (specular < 1% and diffuse < 0.07%) was achieved with high impact, dust, and chemical resistant surface finishes. These touch panels were qualified over a wide operational temperature range, -51°C to +80°C specifically for military and rugged industrial applications.

Rugged, Portable, Real-Time Optical Gaseous Analyzer for Hydrogen Fluoride

NASA Technical Reports Server (NTRS)

Pilgrim, Jeffrey; Gonzales, Paula

2012-01-01

Hydrogen fluoride (HF) is a primary evolved combustion product of fluorinated and perfluorinated hydrocarbons. HF is produced during combustion by the presence of impurities and hydrogen- containing polymers including polyimides. This effect is especially dangerous in closed occupied volumes like spacecraft and submarines. In these systems, combinations of perfluorinated hydrocarbons and polyimides are used for insulating wiring. HF is both highly toxic and short-lived in closed environments due to its reactivity. The high reactivity also makes HF sampling problematic. An infrared optical sensor can detect promptly evolving HF with minimal sampling requirements, while providing both high sensitivity and high specificity. A rugged optical path length enhancement architecture enables both high HF sensitivity and rapid environmental sampling with minimal gaseous contact with the low-reactivity sensor surfaces. The inert optical sample cell, combined with infrared semiconductor lasers, is joined with an analog and digital electronic control architecture that allows for ruggedness and compactness. The combination provides both portability and battery operation on a simple camcorder battery for up to eight hours. Optical detection of gaseous HF is confounded by the need for rapid sampling with minimal contact between the sensor and the environmental sample. A sensor is required that must simultaneously provide the required sub-parts-permillion detection limits, but with the high specificity and selectivity expected of optical absorption techniques. It should also be rugged and compact for compatibility with operation onboard spacecraft and submarines. A new optical cell has been developed for which environmental sampling is accomplished by simply traversing the few mm-thick cell walls into an open volume where the measurement is made. A small, low-power fan or vacuum pump may be used to push or pull the gaseous sample into the sample volume for a response time of a few seconds. The optical cell simultaneously provides for an enhanced optical interaction path length between the environmental sample and the infrared laser. Further, the optical cell itself is comprised of inert materials that render it immune to attack by HF. In some cases, the sensor may be configured so that the optoelectronic devices themselves are protected and isolated from HF by the optical cell. The optical sample cell is combined with custom-developed analog and digital control electronics that provide rugged, compact operation on a platform that can run on a camcorder battery. The sensor is inert with respect to acidic gases like HF, while providing the required sensitivity, selectivity, and response time. Certain types of combustion events evolve copious amounts of HF, very little of other gases typically associated with combustion (e.g., carbon monoxide), and very low levels of aerosols and particulates (which confound traditional smoke detectors). The new sensor platform could warn occupants early enough to take the necessary countermeasures.

Rugged Low-Resistance Contacts To High-Tc Superconductors

NASA Technical Reports Server (NTRS)

Caton, Randall; Selim, Raouf; Byvik, Charles E.; Buoncristiani, A. Martin

1992-01-01

Newly developed technique involving use of gold makes possible to fabricate low-resistance contacts with rugged connections to high-Tc superconductors. Gold diffused into specimen of superconducting material by melting gold beads onto surface of specimen, making strong mechanical contacts. Shear strength of gold bead contacts greater than epoxy or silver paste. Practical use in high-current-carrying applications of new high-Tc materials, including superconducting magnets, long-wavelength sensors, electrical ground planes at low temperatures, and efficient transmission of power.

Urinary tract infection after retrograde urethrogram in children: A multicenter study.

PubMed

Malhotra, Neha R; Green, Jared R; Rigsby, Cynthia K; Holl, Jane L; Cheng, Earl Y; Johnson, Emilie K

2017-12-01

The risk of post-procedural urinary tract infection (ppUTI) after retrograde urethrogram (RUG) has not been well quantified. Prophylactic antibiotics may reduce the risk, but must be weighed against the risks of antibiotic resistance. Prior research has shown that this risk is variable after voiding cystourethrogram (0-42% reported ppUTI rate) and appears to be low after urodynamics (0-4.8%) but this risk has not been well documented for patients undergoing RUG. We aimed to (1) describe the rate of ppUTI after RUG, and (2) examine factors associated with use of antibiotics at the time of RUG. We conducted a retrospective cohort study of children undergoing RUG at two hospitals January 1, 2004, to December 31, 2014. ppUTI within 7 days was measured. Antibiotic prophylaxis was determined. Relationships between clinical characteristics and receipt of pre-procedure antibiotics were evaluated using univariate statistics. Forty-two patients (100% male, median age 11.7 years) underwent 47 RUGs. Indications included trauma (27%), hypospadias (17%), and non-hypospadias (27%) stricture. Study indication and antibiotic administration practices are illustrated in the Figure. Three patients (6.4%) had a history of posterior urethral valves (PUV); one had neurogenic bladder (NGB) (2.4%). Two (4%) studies were performed within 30 days of a clinical UTI and 11% had a positive urinalysis or culture within 30 days pre-RUG. UTI in the 30 days before RUG was not associated with antibiotic prescription (p > 0.99). One child (2.1%; 95% CI 0-6.3%) had a ppUTI: a 7-year-old, uncircumcised male with a history of PUV and voiding dysfunction who was asymptomatic at the time of RUG. Although the risk of ppUTI after RUG appears to be low, the rare occurrence of an iatrogenic UTI can lead to high cost and patient morbidity, particularly in cases similar to our patients who required inpatient admission for intravenous antibiotics. To help balance the risk of UTI with the associated healthcare costs and morbidity with the concerns about antibiotic overuse and potential exposure to drug reaction, data from this study may inform future development of evidence-based guidelines targeting only patients at highest risk for ppUTI with antibiotic prophylaxis. The risk of ppUTI after RUG is low. Antibiotic prophylaxis was unrelated pre-RUG UTI in our population. These results indicate the need for pre-procedural antibiotic prescribing guidelines, and suggest that routine antibiotics prior to RUG are not indicated unless the patient has another indication for antibiotics. Copyright © 2017 Journal of Pediatric Urology Company. Published by Elsevier Ltd. All rights reserved.

Variable speed induction motor operation from a 20-kHz power bus

NASA Technical Reports Server (NTRS)

Hansen, Irving G.

1989-01-01

Induction motors are recognized for their simple rugged construction. To date, however, their application to variable speed or servo drives was hampered by limitations on their control. Induction motor drives tend to be complex and to display troublesome low speed characteristics due in part to nonsinusoidal driving voltages. A technique was developed which involves direct synthesis of sinusoidal driving voltages from a high frequency power bus and independent control of frequency and voltages. Separation of frequency and voltage allows independent control of rotor and stator flux, full four quadrant operation, and instantaneous torque control. Recent test results, current status of the technology, and proposed aerospace applications will be discussed.

Variable speed induction motor operation from a 20-kHz power bus

NASA Technical Reports Server (NTRS)

Hansen, Irving G.

1989-01-01

Induction motors are recognized for their simple rugged construction to date, however, their application to variable speed or servo drives has been hampered by limitations on their control. Induction motor drives tend to be complex and to display troublesome low speed characteristics due in part to nonsinusoidal driving voltages. A technique was developed which involves direct synthesis of sinusoidal driving voltages from a high frequency power bus and independent control of frequency and voltages. Separation offrequency and voltage allows independent control of rotor and stator flux, full four-quadrant operation, and instantaneous torque control. Recent test results, current status of the technology, and proposed aerospace applications will be discussed.

Field Demonstration of a Novel Biotreatment Process for Perchlorate Reduction in Groundwater

DTIC Science & Technology

2010-06-01

biological reduction and/or reaction with ZVI, and arsenic hexavalent chromium and/or uranium by adsorption on corrosion products. • Simple rugged...problems and troubleshooting measures ................................... 22 5.2 Laboratory Evaluation of Porosity Decrease and Corrosion Products...reactor when it was dismantled showing the heavy deposits of iron corrosion products and quasi total loss of porosity. Figure 5.14 Picture of the column

Growth of near-infrared spectroscopy in pharmaceutical and medical sciences

NASA Astrophysics Data System (ADS)

Ciurczak, Emil W.

2002-06-01

Near-IR Spectroscopy (NIRS) is used extensively in the health services industries: medical research, pharmaceutical production, and bioprocessing. NIRS Is rugged, simple to operate, flexible, and relatively inexpensive. It may be used to monitor the progress biochemical reactions. It is used to control mixing, blending, drying, and coating in pharmaceutical production and is used for imaging and chemical determinations in living patients.

Monte Carlo based estimation of organ and effective doses to patients undergoing hysterosalpingography and retrograde urethrography fluoroscopy procedures

NASA Astrophysics Data System (ADS)

Ngaile, J. E.; Msaki, P. K.; Kazema, R. R.

2018-04-01

Contrast investigations of hysterosalpingography (HSG) and retrograde urethrography (RUG) fluoroscopy procedures remain the dominant diagnostic tools for the investigation of infertility in females and urethral strictures in males, respectively, owing to the scarcity and high cost of services of alternative diagnostic technologies. In light of the radiological risks associated with contrast based investigations of the genitourinary tract systems, there is a need to assess the magnitude of radiation burden imparted to patients undergoing HSG and RUG fluoroscopy procedures in Tanzania. The air kerma area product (KAP), fluoroscopy time, number of images, organ dose and effective dose to patients undergoing HSG and RUG procedures were obtained from four hospitals. The KAP was measured using a flat transmission ionization chamber, while the organ and effective doses were estimated using the knowledge of the patient characteristics, patient related exposure parameters, geometry of examination, KAP and Monte Carlo calculations (PCXMC). The median values of KAP for the HSG and RUG were 2.2 Gy cm2 and 3.3 Gy cm2, respectively. The median organ doses in the present study for the ovaries, urinary bladder and uterus for the HSG procedures, were 1.0 mGy, 4.0 mGy and 1.6 mGy, respectively, while for urinary bladder and testes of the RUG were 3.4 mGy and 5.9 mGy, respectively. The median values of effective doses for the HSG and RUG procedures were 0.65 mSv and 0.59 mSv, respectively. The median values of effective dose per hospital for the HSG and RUG procedures had a range of 1.6-2.8 mSv and 1.9-5.6 mSv, respectively, while the overall differences between individual effective doses across the four hospitals varied by factors of up to 22.0 and 46.7, respectively for the HSG and RUG procedures. The proposed diagnostic reference levels (DRLs) for the HSG and RUG were for KAP 2.8 Gy cm2 and 3.9 Gy cm2, for fluoroscopy time 0.8 min and 0.9 min, and for number of images 5 and 4, respectively. The suggested DRLs for the HSG and RUG procedures may be used by the radiology departments in Tanzania for management of attained dose levels until the national DRLs are established.

Comparison of micellar extraction combined with ionic liquid based vortex-assisted liquid-liquid microextraction and modified quick, easy, cheap, effective, rugged, and safe method for the determination of difenoconazole in cowpea.

PubMed

Chen, Xiaochu; Bian, Yanli; Liu, Fengmao; Teng, Peipei; Sun, Pan

2017-10-06

Two simple sample pretreatment for the determination of difenoconazole in cowpea was developed including micellar extraction combined with ionic liquid based vortex-assisted liquid-liquid microextraction (ME-IL-VALLME) prior to high performance liquid chromatography (HPLC), and modified quick, easy, cheap, effective, rugged, and safe method (QuEChERS) coupled with HPLC-MS/MS. In ME-IL-VALLME method, the target analyte was extracted by surfactant Tween 20 micellar solution, then the supernatant was diluted with 3mL water to decrease the solubility of micellar solution. Subsequently, the vortex-assisted liquid-liquid microextraction (VALLME) procedure was performed in the diluted extraction solution by using the ionic liquid of 1-hexyl-3-methylimidazolium hexafluorophosphate ([HMIM]PF 6 ) as the extraction solvent and Tween 20 as an emulsifier to enhance the dispersion of the water-immiscible ionic liquid into the aqueous phase. Parameters that affect the extraction have been investigated in both methods Under the optimum conditions, the limits of quantitation were 0.10 and 0.05mgkg -1 , respectively. And good linearity was achieved with the correlation coefficient higher than 0.9941. The relative recoveries ranged from 78.6 to 94.8% and 92.0 to 118.0% with the relative standard deviations (RSD) of 7.9-9.6% and 1.2-3.2%, respectively. Both methods were quick, simple and inexpensive. However, the ME-IL-VALLME method provides higher enrichment factor compared with conventional QuEChERS method. The ME-IL-VALLME method has a strong potential for the determination of difenoconazole in complex vegetable matrices with HPLC. Copyright © 2017 Elsevier B.V. All rights reserved.

Evaluation of coarse scale land surface remote sensing albedo product over rugged terrain

NASA Astrophysics Data System (ADS)

Wen, J.; Xinwen, L.; You, D.; Dou, B.

2017-12-01

Satellite derived Land surface albedo is an essential climate variable which controls the earth energy budget and it can be used in applications such as climate change, hydrology, and numerical weather prediction. The accuracy and uncertainty of surface albedo products should be evaluated with a reliable reference truth data prior to applications. And more literatures investigated the validation methods about the albedo validation in a flat or homogenous surface. However, the albedo performance over rugged terrain is still unknow due to the validation method limited. A multi-validation strategy is implemented to give a comprehensive albedo validation, which will involve the high resolution albedo processing, high resolution albedo validation based on in situ albedo, and the method to upscale the high resolution albedo to a coarse scale albedo. Among them, the high resolution albedo generation and the upscale method is the core step for the coarse scale albedo validation. In this paper, the high resolution albedo is generated by Angular Bin algorithm. And a albedo upscale method over rugged terrain is developed to obtain the coarse scale albedo truth. The in situ albedo located 40 sites in mountain area are selected globally to validate the high resolution albedo, and then upscaled to the coarse scale albedo by the upscale method. This paper takes MODIS and GLASS albedo product as a example, and the prelimarily results show the RMSE of MODIS and GLASS albedo product over rugged terrain are 0.047 and 0.057, respectively under the RMSE with 0.036 of high resolution albedo.

Evolution at ‘Sutures’ and ‘Centers’: Recombination Can Aid Adaptation of Spatially Structured Populations on Rugged Fitness Landscapes

PubMed Central

Cooper, Jacob D.; Kerr, Benjamin

2016-01-01

Epistatic interactions among genes can give rise to rugged fitness landscapes, in which multiple “peaks” of high-fitness allele combinations are separated by “valleys” of low-fitness genotypes. How populations traverse rugged fitness landscapes is a long-standing question in evolutionary biology. Sexual reproduction may affect how a population moves within a rugged fitness landscape. Sex may generate new high-fitness genotypes by recombination, but it may also destroy high-fitness genotypes by shuffling the genes of a fit parent with a genetically distinct mate, creating low-fitness offspring. Either of these opposing aspects of sex require genotypic diversity in the population. Spatially structured populations may harbor more diversity than well-mixed populations, potentially amplifying both positive and negative effects of sex. On the other hand, spatial structure leads to clumping in which mating is more likely to occur between like types, diminishing the effects of recombination. In this study, we use computer simulations to investigate the combined effects of recombination and spatial structure on adaptation in rugged fitness landscapes. We find that spatially restricted mating and offspring dispersal may allow multiple genotypes inhabiting suboptimal peaks to coexist, and recombination at the “sutures” between the clusters of these genotypes can create genetically novel offspring. Sometimes such an offspring genotype inhabits a new peak on the fitness landscape. In such a case, spatially restricted mating allows this fledgling subpopulation to avoid recombination with distinct genotypes, as mates are more likely to be the same genotype. Such population “centers” can allow nascent peaks to establish despite recombination. Spatial structure may therefore allow an evolving population to enjoy the creative side of sexual recombination while avoiding its destructive side. PMID:27973606

A New Method for Unconstrained Heart Rate Monitoring

DTIC Science & Technology

2001-10-25

members. However, care of bedridden elderly persons are not easy task, and this caused severe psychological and financial problems for other family...physical and mental conditions of bedridden elderly people at home and patients at hospitals and to contribute to the labor saving of the care and the...not suitable for home care of bedridden elderly people. Our method provides very small, simple and mechanically rugged device suitable for home

GaAs MOEMS Technology

DOE Office of Scientific and Technical Information (OSTI.GOV)

SPAHN, OLGA B.; GROSSETETE, GRANT D.; CICH, MICHAEL J.

2003-03-01

Many MEMS-based components require optical monitoring techniques using optoelectronic devices for converting mechanical position information into useful electronic signals. While the constituent piece-parts of such hybrid opto-MEMS components can be separately optimized, the resulting component performance, size, ruggedness and cost are substantially compromised due to assembly and packaging limitations. GaAs MOEMS offers the possibility of monolithically integrating high-performance optoelectronics with simple mechanical structures built in very low-stress epitaxial layers with a resulting component performance determined only by GaAs microfabrication technology limitations. GaAs MOEMS implicitly integrates the capability for radiation-hardened optical communications into the MEMS sensor or actuator component, a vitalmore » step towards rugged integrated autonomous microsystems that sense, act, and communicate. This project establishes a new foundational technology that monolithically combines GaAs optoelectronics with simple mechanics. Critical process issues addressed include selectivity, electrochemical characteristics, and anisotropy of the release chemistry, and post-release drying and coating processes. Several types of devices incorporating this novel technology are demonstrated.« less

Visible high-power laser sources for today and beyond

NASA Astrophysics Data System (ADS)

Smolka, Gregory L.

1995-04-01

The diversity and proliferation of 'real-world' laser applications continues to put increasing demand on laser technology. New system constraints, often dictated by the operation environment, stretch the capabilities of conventional laboratory lasers. As the applications proliferate, so too do the users. Today's laser user is often not a laser engineer, but rather views the laser simply as a tool to help him perform his job. For lasers to reach their true market potential, laser designers must respond to these user-mandated requirements with simple, compact, rugged devices. Traditional commercial lasers are far too large, bulky and complex for many of these new applications. Design techniques for shrinking, simplifying the ruggedizing solid-state lasers for today's applications will be discussed.

PORPHOBILINOGEN DEAMINASE Deficiency Alters Vegetative and Reproductive Development and Causes Lesions in Arabidopsis

PubMed Central

Quesada, Víctor; Hricová, Andrea; Ponce, María Rosa; Micol, José Luis

2013-01-01

The Arabidopsis rugosa1 (rug1) mutant has irregularly shaped leaves and reduced growth. In the absence of pathogens, leaves of rug1 plants have spontaneous lesions reminiscent of those seen in lesion-mimic mutants; rug1 plants also express cytological and molecular markers associated with defence against pathogens. These rug1 phenotypes are made stronger by dark/light transitions. The rug1 mutant also has delayed flowering time, upregulation of the floral repressor FLOWERING LOCUS C (FLC) and downregulation of the flowering promoters FT and SOC1/AGL20. Vernalization suppresses the late flowering phenotype of rug1 by repressing FLC. Microarray analysis revealed that 280 nuclear genes are differentially expressed between rug1 and wild type; almost a quarter of these genes are involved in plant defence. In rug1, the auxin response is also affected and several auxin-responsive genes are downregulated. We identified the RUG1 gene by map-based cloning and found that it encodes porphobilinogen deaminase (PBGD), also known as hydroxymethylbilane synthase, an enzyme of the tetrapyrrole biosynthesis pathway, which produces chlorophyll, heme, siroheme and phytochromobilin in plants. PBGD activity is reduced in rug1 plants, which accumulate porphobilinogen. Our results indicate that Arabidopsis PBGD deficiency impairs the porphyrin pathway and triggers constitutive activation of plant defence mechanisms leading to leaf lesions and affecting vegetative and reproductive development. PMID:23308205

Rugged: an operational, open-source solution for Sentinel-2 mapping

NASA Astrophysics Data System (ADS)

Maisonobe, Luc; Seyral, Jean; Prat, Guylaine; Guinet, Jonathan; Espesset, Aude

2015-10-01

When you map the entire Earth every 5 days with the aim of generating high-quality time series over land, there is no room for geometrical error: the algorithms have to be stable, reliable, and precise. Rugged, a new open-source library for pixel geolocation, is at the geometrical heart of the operational processing for Sentinel-2. Rugged performs sensor-to-terrain mapping taking into account ground Digital Elevation Models, Earth rotation with all its small irregularities, on-board sensor pixel individual lines-of-sight, spacecraft motion and attitude, and all significant physical effects. It provides direct and inverse location, i.e. it allows the accurate computation of which ground point is viewed from a specific pixel in a spacecraft instrument, and conversely which pixel will view a specified ground point. Direct and inverse location can be used to perform full ortho-rectification of images and correlation between sensors observing the same area. Implemented as an add-on for Orekit (Orbits Extrapolation KIT; a low-level space dynamics library), Rugged also offers the possibility of simulating satellite motion and attitude auxiliary data using Orekit's full orbit propagation capability. This is a considerable advantage for test data generation and mission simulation activities. Together with the Orfeo ToolBox (OTB) image processing library, Rugged provides the algorithmic core of Sentinel-2 Instrument Processing Facilities. The S2 complex viewing model - with 12 staggered push-broom detectors and 13 spectral bands - is built using Rugged objects, enabling the computation of rectification grids for mapping between cartographic and focal plane coordinates. These grids are passed to the OTB library for further image resampling, thus completing the ortho-rectification chain. Sentinel-2 stringent operational requirements to process several terabytes of data per week represented a tough challenge, though one that was well met by Rugged in terms of the robustness and performance of the library.

77 FR 44684 - General Dynamics Itronix Corporation; A Subsidiary of General Dynamics Corporation, Including...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-30

... program management services for rugged laptop computers and rugged mobile devices. The worker group... of program management services for rugged laptop computers and rugged mobile devices, meet the worker... threatened to become totally or partially separated. Section 222(a)(2)(A)(i) has been met because the sales...

MOEs for Drug Interdiction: Simple Tests Expose Critical Flaws

DTIC Science & Technology

1991-09-01

operations against illegal !rugs flowing into the U.S. Six candidate measures of effective (MOEs) are subjected to a structured assessment prcess that tests...supports spanning the decision space with a minimum number of MOEs. A small suite of MOEs reflecting relatively pure effects is preferred to long and...responds to changing consumer fashion--this year’s drug of choice may be overtaken by a new fad. Patterns of preference can vary widely by location as

Applying Resource Utilization Groups (RUG-III) in Hong Kong Nursing Homes

ERIC Educational Resources Information Center

Chou, Kee-Lee; Chi, Iris; Leung, Joe C. B.

2008-01-01

Resource Utilization Groups III (RUG-III) is a case-mix system developed in the United States for categorization of nursing home residents and the financing of residential care services. In Hong Kong, RUG-III is based on several board groups of residents. The aim of this study was to examine the reliability and validity of the RUG-III in Hong Kong…

Perception, planning, and control for walking on rugged terrain

NASA Technical Reports Server (NTRS)

Simmons, Reid; Krotkov, Eric

1991-01-01

The CMU Planetary Rover project is developing a six-legged walking robot capable of autonomously navigating, exploring, and acquiring samples in rugged, unknown environments. To gain experience with the problems involved in walking on rugged terrain, a full-scale prototype leg was built and mounted on a carriage that rolls along overhead rails. Issues addressed in developing the software system to autonomously walk the leg through rugged terrain are described. In particular, the insights gained into perceiving and modeling rugged terrain, controlling the legged mechanism, interacting with the ground, choosing safe yet effective footfalls, and planning efficient leg moves through space are described.

Patient-reported quality indicators for osteoarthritis: a patient and public generated self-report measure for primary care.

PubMed

Blackburn, Steven; Higginbottom, Adele; Taylor, Robert; Bird, Jo; Østerås, Nina; Hagen, Kåre Birger; Edwards, John J; Jordan, Kelvin P; Jinks, Clare; Dziedzic, Krysia

2016-01-01

People with osteoarthritis desire high quality care, support and information. However, the quality of care for people with OA in general practice is not routinely collected. Quality Indicators can be used to benefit patients by measuring whether minimum standards of quality care are being met from a patient perspective. The aim of this study was to describe how a Research User Group (RUG) worked alongside researchers to co-produce a set of self-reported quality indicators for people with osteoarthritis when visiting their general practitioner or practice nurse (primary care). These were required in the MOSAICS study, which developed and evaluated a new model of supported self-management of OA to implement the NICE quality standards for OA. This article describes the public involvement in the MOSAICS study. This was 1) the co-development by RUG members and researchers of an Osteoarthritis Quality Indicators United Kingdom (OA QI (UK)) questionnaire for use in primary care, and 2) the comparison of the OA QI (UK) with a similar questionnaire developed in Norway. This study shows how important and effective a research user group can be in working with researchers in developing quality care indicators for osteoarthritis for use in a research study and, potentially, routine use in primary care. The questionnaire is intended to benefit patients by enabling the assessment of the quality of primary care for osteoarthritis from a patient's perspective. The OA QI (UK) has been used to examine differences in the quality of osteoarthritis care in four European countries. Background People with osteoarthritis (OA) desire high quality care, support and information about OA. However, the quality of care for people with OA in general practice is not routinely collected. Quality Indicators (QI) can be used to benefit patients by measuring whether minimum standards of quality care (e.g. NICE quality standards) are being met from a patient perspective. A Research User Group (RUG) worked with researchers to co-produce a set of self-report, patient-generated QIs for OA. The QIs were intended for use in the MOSAICS study, which developed and evaluated a new model of supported self-management of OA to implement the NICE guidelines. We report on 1) the co-development of the OA QI (UK) questionnaire for primary care; and 2) the comparison of the content of the OA QI (UK) questionnaire with a parallel questionnaire developed in Norway for the Musculoskeletal Pain in Ullensaker (MUST) study. Methods Researchers were invited to OA RUG meetings. Firstly, RUG members were asked to consider factors important to patients consulting their general practitioner (GP) for OA and then each person rated their five most important. RUG members then discussed these in relation to a systematic review of OA QIs in order to form a list of OA QIs from a patient perspective. RUG members suggested wording and response options for a draft OA QI (UK) questionnaire to assess the QIs. Finally RUG members commented on draft and final versions of the questionnaire and how it compared with a translated Norwegian OA-QI questionnaire. Results RUG members (5 males, 5 females; aged 52-80 years) attended up to four meetings. RUG members ranked 20 factors considered most important to patients consulting their GP for joint pain. Following discussion, a list of eleven patient-reported QIs for OA consultations were formed. RUG members then suggested the wording and response options of 16 draft items - four QIs were split into two or more questionnaire items to avoid multiple dimensions of care quality within a single item. On comparison of this to the Norwegian OA-QI questionnaire, RUG members commented that both questionnaires contained seven similar QIs. The RUG members and researchers agreed to adopt the Norwegian OA-QI wording for four of these items. RUG members also recommended adopting an additional seven items from the Norwegian OA-QI with some minor word changes to improve their suitability for patients in the UK. One other item from the draft OA QI (UK) questionnaire was retained and eight items were excluded, resulting in a 15-item final version. Conclusions This study describes the development of patient-reported quality indicators for OA primary care derived by members of a RUG group, working in partnership with the research team throughout the study. The OA QI (UK) supports the NICE quality standards for OA and they have been successfully used to assess the quality of OA consultations in primary care in the MOSAICS study. The OA QI (UK) has the potential for routine use in primary care to assess the quality of OA care provided to patients. Ongoing research using both the UK and Norwegian OA-QI questionnaires is assessing the self-reported quality of OA care in different European populations.

Rugged sensor window materials for harsh environments

NASA Astrophysics Data System (ADS)

Bayya, Shyam; Villalobos, Guillermo; Kim, Woohong; Sanghera, Jasbinger; Hunt, Michael; Aggarwal, Ishwar D.

2014-09-01

There are several military or commercial systems operating in very harsh environments that require rugged windows. On some of these systems, windows become the single point of failure. These applications include sensor or imaging systems, high-energy laser weapons systems, submarine photonic masts, IR countermeasures and missiles. Based on the sea or land or air based platforms the window or dome on these systems must withstand wave slap, underwater or ground based explosions, or survive flight through heavy rain and sand storms while maintaining good optical transmission in the desired wavelength range. Some of these applications still use softer ZnS or fused silica windows because of lack of availability of rugged materials in shapes or sizes required. Sapphire, ALON and spinel are very rugged materials with significantly higher strengths compared to ZnS and fused silica. There have been recent developments in spinel, ALON and sapphire materials to fabricate in large sizes and conformal shapes. We have been developing spinel ceramics for several of these applications. We are also developing β-SiC as a transparent window material as it has higher hardness, strength, and toughness than sapphire, ALON and spinel. This paper gives a summary of our recent findings.

Refining a case-mix measure for nursing homes: Resource Utilization Groups (RUG-III).

PubMed

Fries, B E; Schneider, D P; Foley, W J; Gavazzi, M; Burke, R; Cornelius, E

1994-07-01

A case-mix classification system for nursing home residents is developed, based on a sample of 7,658 residents in seven states. Data included a broad assessment of resident characteristics, corresponding to items of the Minimum Data Set, and detailed measurement of nursing staff care time over a 24-hour period and therapy staff time over a 1-week period. The Resource Utilization Groups, Version III (RUG-III) system, with 44 distinct groups, achieves 55.5% variance explanation of total (nursing and therapy) per diem cost and meets goals of clinical validity and payment incentives. The mean resource use (case-mix index) of groups spans a nine-fold range. The RUG-III system improves on an earlier version not only by increasing the variance explanation (from 43%), but, more importantly, by identifying residents with "high tech" procedures (e.g., ventilators, respirators, and parenteral feeding) and those with cognitive impairments; by using better multiple activities of daily living; and by providing explicit qualifications for the Medicare nursing home benefit. RUG-III is being implemented for nursing home payment in 11 states (six as part of a federal multistate demonstration) and can be used in management, staffing level determination, and quality assurance.

Resource utilization groups (RUGs): defining chronic care, rehabilitation and nursing home case mix in Canada.

PubMed

Botz, C K; Bestard, S; Demaray, M; Molloy, G

1993-01-01

The two major purposes of this study were: (1) to evaluate Resource Utilization Groups (RUGs III) as a unified method for classifying all residential, chronic care and rehabilitation patients at the St. Joseph's Health Centre, London, and (2) to compare the potential funding implications of RUGs and other patient/resident classification systems. RUGs were used to classify a total of 336 patients/residents in residential, extended care, chronic care and rehabilitation beds at the Health Centre. Patients were also concurrently classified according to the Alberta Long Term Care Classification System and the Medicus Long Term Care System. Results show that RUGs provide relatively more credit for higher acuity patients than do the Alberta or Medicus systems. If used as a basis for funding, chronic care and rehabilitation hospitals would be entitled to more funding (relative to residential/nursing homes) under RUGs than under the other two patient classification mechanisms.

Chemiluminescent Determination of Oxamyl in Drinking Water and Tomato Using Online Postcolumn UV Irradiation in a Chromatographic System.

PubMed

Murillo Pulgarín, José A; García Bermejo, Luisa F; Durán, Armando Carrasquero

2018-03-07

High-performance liquid chromatography (HPLC) was used to separate oxamyl from other pesticides in drinking water and tomato paste. The eluate emerging from the column tail was mixed with an alkaline solution of Co 2+ in EDTA and irradiated with UV light to induce photolysis of the carbamate in order to obtain free radicals and other reactive species that oxidize luminol and produce chemiluminescence (CL) as a result. The intensity of the CL signal was monitored in the form of chromatographic peaks. Under the optimum operating conditions for the HPLC-UV-CL system, the analyte concentration was linearly related to peak area. The limit of detection as determined in accordance with the IUPAC criterion was 0.17 mg L -1 . Oxamyl was successfully extracted with recoveries of 88.7-103.1% from spiked tomato paste by using a simple QuEChERS (Quick, Easy, Cheap, Effective, Rugged, and Safe) sample preparation approach. Similar recoveries were obtained from drinking water samples spiked with oxamyl concentrations above the LOD. The proposed method is a simple, fast, accurate choice for quantifying this pesticide.

GA-optimized feedforward-PID tracking control for a rugged electrohydraulic system design.

PubMed

Sarkar, B K; Mandal, P; Saha, R; Mookherjee, S; Sanyal, D

2013-11-01

Rugged electrohydraulic systems are preferred for remote and harsh applications. Despite the low bandwidth, large deadband and flow nonlinearities in proportional valves valve and highly nonlinear friction in industry-grade cylinders that comprise rugged systems, their maintenance are much easier than very sophisticated and delicate servocontrol and servocylinder systems. With the target of making the easily maintainable system to perform comparably to a servosystem, a feedforward control has been designed here for compensating the nonlinearities. A PID feedback of the piston displacement has been employed in tandem for absorbing the unmodeled effects. All the controller parameters have been optimized by a real-coded genetic algorithm. The agreement between the achieved real-time responses for step and sinusoidal demands with those achieved by modern servosystems clearly establishes the acceptability of the controller design. Copyright © 2013 ISA. Published by Elsevier Ltd. All rights reserved.

Deployment of quasi-digital sensor for high temperature molten salt level measurement in pyroprocessing plants.

PubMed

Sanga, Ramesh; Agarwal, Sourabh; Sivaramakrishna, M; Rao, G Prabhakara

2018-04-01

Development of a liquid molten salt level sensor device that can detect the level of liquid molten salt in the process vessels of pyrochemical reprocessing of spent metallic fuels is detailed. It is proposed to apply a resistive-type pulsating sensor-based level measurement approach. There are no commercially available sensors due to limitations of high temperature, radiation, and physical dimensions. A compact, simple, rugged, low power, and high precise pulsating sensor-based level probe and simple instrumentation for the molten salt liquid level sensor to work in the extreme conditions has been indigenously developed, with high precision and accuracy. The working principle, design concept, and results have been discussed. This level probe is mainly composed of the variable resistor made up of ceramic rods. This resistor constitutes the part of resistance-capacitance-type Logic Gate Oscillator (LGO). A change in the molten salt level inside the tank causes a small change in the resistance which in turn changes the pulse frequency of the LGO. Thus the frequency, the output of the instrument that is displayed on the LCD of an embedded system, is a function of molten salt level. In the present design, the range of level measurement is about 10 mm. The sensitivity in position measurement up to 10 mm is ∼2.5 kHz/mm.

Deployment of quasi-digital sensor for high temperature molten salt level measurement in pyroprocessing plants

NASA Astrophysics Data System (ADS)

Sanga, Ramesh; Agarwal, Sourabh; Sivaramakrishna, M.; Rao, G. Prabhakara

2018-04-01

Development of a liquid molten salt level sensor device that can detect the level of liquid molten salt in the process vessels of pyrochemical reprocessing of spent metallic fuels is detailed. It is proposed to apply a resistive-type pulsating sensor-based level measurement approach. There are no commercially available sensors due to limitations of high temperature, radiation, and physical dimensions. A compact, simple, rugged, low power, and high precise pulsating sensor-based level probe and simple instrumentation for the molten salt liquid level sensor to work in the extreme conditions has been indigenously developed, with high precision and accuracy. The working principle, design concept, and results have been discussed. This level probe is mainly composed of the variable resistor made up of ceramic rods. This resistor constitutes the part of resistance-capacitance-type Logic Gate Oscillator (LGO). A change in the molten salt level inside the tank causes a small change in the resistance which in turn changes the pulse frequency of the LGO. Thus the frequency, the output of the instrument that is displayed on the LCD of an embedded system, is a function of molten salt level. In the present design, the range of level measurement is about 10 mm. The sensitivity in position measurement up to 10 mm is ˜2.5 kHz/mm.

Explaining direct care resource use of nursing home residents: findings from time studies in four states.

PubMed

Arling, Greg; Kane, Robert L; Mueller, Christine; Lewis, Teresa

2007-04-01

To explain variation in direct care resource use (RU) of nursing home residents based on the Resource Utilization Groups III (RUG-III) classification system and other resident- and unit-level explanatory variables. Primary data were collected on 5,314 nursing home residents in 156 nursing units in 105 facilities from four states (CO, IN, MN, MS) from 1998 to 2004. Study Design. Nurses and other direct care staff recorded resident-specific and other time caring for all residents on sampled nursing units. Care time was linked to resident data from the Minimum Data Set assessment instrument. Major variables were: RUG-III group (34-group), other health and functional conditions, licensed and other professional minutes per day, unlicensed minutes per day, and direct care RU (wage-weighted minutes). Resident- and unit-level relationships were examined through hierarchical linear modeling. Time study data were recorded with hand-held computers, verified for accuracy by project staff at the data collection sites and then merged into resident and unit-level data sets. Resident care time and RU varied between and within nursing units. RUG-III group was related to RU; variables such as length of stay and unit percentage of high acuity residents also were significantly related. Case-mix indices (CMIs) constructed from study data displayed much less variation across RUG-III groups than CMIs from earlier time studies. Results from earlier time studies may not be representative of care patterns of Medicaid and private pay residents. New RUG-III CMIs should be developed to better reflect the relative costs of caring for these residents.

Slipping and tripping: fall injuries in adults associated with rugs and carpets

PubMed Central

Rosen, Tony; Mack, Karin A.; Noonan, Rita K.

2013-01-01

Abstract: Background: Falls are a leading cause of unintentional injury among adults age 65 years and older. Loose, unsecured rugs and damaged carpets with curled edges, are recognized environmental hazards that may contribute to falls. To characterize nonfatal, unintentional fall-related injuries associated with rugs and carpets in adults aged 65 years and older. Methods: We conducted a retrospective analysis of surveillance data of injuries treated in hospital emergency departments (EDs) during 2001–2008. We used the National Electronic Injury Surveillance System-All Injury Program, which collects data from a nationally representative stratified probability sample of 66 U.S. hospital EDs. Sample weights were used to make national estimates. Results: Annually, an estimated 37,991 adults age 65 years or older were treated in U.S. EDs for falls associated with carpets (54.2%) and rugs (45.8%). Most falls (72.8%) occurred at home. Women represented 80.2% of fall injuries. The most common location for fall injuries in the home was the bathroom (35.7%). Frequent fall injuries occurred at the transition between carpet/rug and non-carpet/rug, on wet carpets or rugs, and while hurrying to the bathroom. Conclusions: Fall injuries associated with rugs and carpets are common and may cause potentially severe injuries. Older adults, their caregivers, and emergency and primary care physicians should be aware of the significant risk for fall injuries and of environmental modifications that may reduce that risk. PMID:22868399

The 25 kWe solar thermal Stirling hydraulic engine system: Conceptual design

NASA Technical Reports Server (NTRS)

White, Maurice; Emigh, Grant; Noble, Jack; Riggle, Peter; Sorenson, Torvald

1988-01-01

The conceptual design and analysis of a solar thermal free-piston Stirling hydraulic engine system designed to deliver 25 kWe when coupled to a 11 meter test bed concentrator is documented. A manufacturing cost assessment for 10,000 units per year was made. The design meets all program objectives including a 60,000 hr design life, dynamic balancing, fully automated control, more than 33.3 percent overall system efficiency, properly conditioned power, maximum utilization of annualized insolation, and projected production costs. The system incorporates a simple, rugged, reliable pool boiler reflux heat pipe to transfer heat from the solar receiver to the Stirling engine. The free-piston engine produces high pressure hydraulic flow which powers a commercial hydraulic motor that, in turn, drives a commercial rotary induction generator. The Stirling hydraulic engine uses hermetic bellows seals to separate helium working gas from hydraulic fluid which provides hydrodynamic lubrication to all moving parts. Maximum utilization of highly refined, field proven commercial components for electric power generation minimizes development cost and risk.

Explaining Direct Care Resource Use of Nursing Home Residents: Findings from Time Studies in Four States

PubMed Central

Arling, Greg; Kane, Robert L; Mueller, Christine; Lewis, Teresa

2007-01-01

Objective To explain variation in direct care resource use (RU) of nursing home residents based on the Resource Utilization Groups III (RUG-III) classification system and other resident- and unit-level explanatory variables. Data Sources/Study Setting Primary data were collected on 5,314 nursing home residents in 156 nursing units in 105 facilities from four states (CO, IN, MN, MS) from 1998 to 2004. Study Design Nurses and other direct care staff recorded resident-specific and other time caring for all residents on sampled nursing units. Care time was linked to resident data from the Minimum Data Set assessment instrument. Major variables were: RUG-III group (34-group), other health and functional conditions, licensed and other professional minutes per day, unlicensed minutes per day, and direct care RU (wage-weighted minutes). Resident- and unit-level relationships were examined through hierarchical linear modeling. Data Collection/Extraction Methods Time study data were recorded with hand-held computers, verified for accuracy by project staff at the data collection sites and then merged into resident and unit-level data sets. Principal Findings Resident care time and RU varied between and within nursing units. RUG-III group was related to RU; variables such as length of stay and unit percentage of high acuity residents also were significantly related. Case-mix indices (CMIs) constructed from study data displayed much less variation across RUG-III groups than CMIs from earlier time studies. Conclusions Results from earlier time studies may not be representative of care patterns of Medicaid and private pay residents. New RUG-III CMIs should be developed to better reflect the relative costs of caring for these residents. PMID:17362220

Applying RUG-III in Japanese Long-Term Care Facilities.

ERIC Educational Resources Information Center

Ikegami, Naoki; And Others

1994-01-01

Tested U.S. nursing home case-mix system, Resource Utilization Groups, Version III (RUG-III) in Japanese long-term care facilities. Measured staff time and resident characteristics for 871 patients. Found acceptable reliability for items defining RUG-III, and system explained 44% of variance in wage-weighted staff time (cost). Japanese and U.S.…

16 CFR 1631.34 - Small carpets and rugs not meeting acceptance criterion.

Code of Federal Regulations, 2011 CFR

2011-01-01

... proximity to the edge of the small carpet or rug. (b) Such cautionary statements shall also appear in a... or effect the sale of small carpets or rugs shall be labeled with the information required by this... samples, swatches, or specimens used to promote or effect the sale thereof, which is not in compliance...

16 CFR 1631.34 - Small carpets and rugs not meeting acceptance criterion.

Code of Federal Regulations, 2014 CFR

2014-01-01

... proximity to the edge of the small carpet or rug. (b) Such cautionary statements shall also appear in a... or effect the sale of small carpets or rugs shall be labeled with the information required by this... samples, swatches, or specimens used to promote or effect the sale thereof, which is not in compliance...

16 CFR § 1631.34 - Small carpets and rugs not meeting acceptance criterion.

Code of Federal Regulations, 2013 CFR

2013-01-01

... proximity to the edge of the small carpet or rug. (b) Such cautionary statements shall also appear in a... or effect the sale of small carpets or rugs shall be labeled with the information required by this... samples, swatches, or specimens used to promote or effect the sale thereof, which is not in compliance...

16 CFR 1631.34 - Small carpets and rugs not meeting acceptance criterion.

Code of Federal Regulations, 2012 CFR

2012-01-01

... proximity to the edge of the small carpet or rug. (b) Such cautionary statements shall also appear in a... or effect the sale of small carpets or rugs shall be labeled with the information required by this... samples, swatches, or specimens used to promote or effect the sale thereof, which is not in compliance...

Application of Biased Metropolis Algorithms: From protons to proteins

PubMed Central

Bazavov, Alexei; Berg, Bernd A.; Zhou, Huan-Xiang

2015-01-01

We show that sampling with a biased Metropolis scheme is essentially equivalent to using the heatbath algorithm. However, the biased Metropolis method can also be applied when an efficient heatbath algorithm does not exist. This is first illustrated with an example from high energy physics (lattice gauge theory simulations). We then illustrate the Rugged Metropolis method, which is based on a similar biased updating scheme, but aims at very different applications. The goal of such applications is to locate the most likely configurations in a rugged free energy landscape, which is most relevant for simulations of biomolecules. PMID:26612967

Applying Resource Utilization Groups (RUG-III) in Hong Kong nursing homes.

PubMed

Chou, Kee-Lee; Chi, Iris; Leung, Joe C B

2008-01-01

Resource Utilization Groups III (RUG-III) is a case-mix system developed in the United States for categorization of nursing home residents and the financing of residential care services. In Hong Kong, RUG-III is based on several board groups of residents. The aim of this study was to examine the reliability and validity of the RUG-III in Hong Kong nursing homes. A cross-sectional survey was conducted in seven residential facilities operated by one agency. Residents ( N = 1,127) were assessed by the Minimum Data Set (MDS) and nursing as well as auxiliary staff care times were recorded within 2 weeks before or after the completion of MDS assessment. Forty-five out 1,127 residents were re-interviewed by an independent assessor to assess the inter-rater reliability. The inter-rater reliability of MDS assessment was excellent (kappa = 0.76) and the original RUG-III accounted for about 30 per cent of nursing staff time. Results provide preliminary evidence to support that RUG-III is a reliable and valid case-mix system for Hong Kong nursing homes, but future studies must be explored to reduce the variance of resource use explained by this case-mix system.

A High-Value, Low-Cost Bubble Continuous Positive Airway Pressure System for Low-Resource Settings: Technical Assessment and Initial Case Reports

PubMed Central

Brown, Jocelyn; Machen, Heather; Kawaza, Kondwani; Mwanza, Zondiwe; Iniguez, Suzanne; Lang, Hans; Gest, Alfred; Kennedy, Neil; Miros, Robert; Richards-Kortum, Rebecca; Molyneux, Elizabeth; Oden, Maria

2013-01-01

Acute respiratory infections are the leading cause of global child mortality. In the developing world, nasal oxygen therapy is often the only treatment option for babies who are suffering from respiratory distress. Without the added pressure of bubble Continuous Positive Airway Pressure (bCPAP) which helps maintain alveoli open, babies struggle to breathe and can suffer serious complications, and frequently death. A stand-alone bCPAP device can cost $6,000, too expensive for most developing world hospitals. Here, we describe the design and technical evaluation of a new, rugged bCPAP system that can be made in small volume for a cost-of-goods of approximately $350. Moreover, because of its simple design—consumer-grade pumps, medical tubing, and regulators—it requires only the simple replacement of a <$1 diaphragm approximately every 2 years for maintenance. The low-cost bCPAP device delivers pressure and flow equivalent to those of a reference bCPAP system used in the developed world. We describe the initial clinical cases of a child with bronchiolitis and a neonate with respiratory distress who were treated successfully with the new bCPAP device. PMID:23372661

Adaptive finite volume methods with well-balanced Riemann solvers for modeling floods in rugged terrain: Application to the Malpasset dam-break flood (France, 1959)

USGS Publications Warehouse

George, D.L.

2011-01-01

The simulation of advancing flood waves over rugged topography, by solving the shallow-water equations with well-balanced high-resolution finite volume methods and block-structured dynamic adaptive mesh refinement (AMR), is described and validated in this paper. The efficiency of block-structured AMR makes large-scale problems tractable, and allows the use of accurate and stable methods developed for solving general hyperbolic problems on quadrilateral grids. Features indicative of flooding in rugged terrain, such as advancing wet-dry fronts and non-stationary steady states due to balanced source terms from variable topography, present unique challenges and require modifications such as special Riemann solvers. A well-balanced Riemann solver for inundation and general (non-stationary) flow over topography is tested in this context. The difficulties of modeling floods in rugged terrain, and the rationale for and efficacy of using AMR and well-balanced methods, are presented. The algorithms are validated by simulating the Malpasset dam-break flood (France, 1959), which has served as a benchmark problem previously. Historical field data, laboratory model data and other numerical simulation results (computed on static fitted meshes) are shown for comparison. The methods are implemented in GEOCLAW, a subset of the open-source CLAWPACK software. All the software is freely available at. Published in 2010 by John Wiley & Sons, Ltd.

Air-assisted liquid-liquid microextraction integrated with QuEChERS for determining endocrine-disrupting compounds in fish by high-performance liquid chromatography-tandem mass spectrometry.

PubMed

Luo, Zhoufei; Lu, Jing; Li, Haipu; Tu, Yi; Wan, Yuehao; Yang, Zhaoguang

2018-09-15

A new, sensitive, and rapid method based on the Quick, Easy, Cheap, Effective, Rugged and Safe (QuEChERS) approach and air-assisted liquid-liquid microextraction (AALLME) technology was developed for the determination of 20 endocrine-disrupting compounds (EDCs) in fish by high-performance liquid chromatography-tandem mass spectrometry. The method first integrates AALLME into QuEChERS to achieve clean-up and enrichment of the EDCs in one step. A self-made glass tube was enfolded with plasticine to withstand the high centrifugal force. The established method was developed by optimization of the parameters. High linearities (R 2  > 0.9924) and recoveries (78.2-118.6%) at three spiked levels (5, 10, and 20 ng g -1 ), and low relative standard deviation values (1.1-14.5%) and limits of detection (0.03-0.80 ng g -1 ) were obtained. The method comparison shows that the proposed method is superior as it involves less organic solvent usage, simple operation and high efficiency. This method was successfully applied to different fishes for analyzing EDCs. Copyright © 2018 Elsevier Ltd. All rights reserved.

16 CFR 1630.63 - Suspension of washing requirements for carpets and rugs with alumina trihydrate in the backing.

Code of Federal Regulations, 2010 CFR

2010-01-01

... of Carpets and Rugs (FF 1-70) at § 1630.4(b)(1)(ii) provides that if a carpet or rug has had a fire-retardant treatment, or is made of fibers which have had a fire-retardant treatment, the sample or oversized... specimens either 10 times under the washing and drying procedure prescribed in Method 124-1996 of the...

16 CFR 1630.63 - Suspension of washing requirements for carpets and rugs with alumina trihydrate in the backing.

Code of Federal Regulations, 2012 CFR

2012-01-01

... of Carpets and Rugs (FF 1-70) at § 1630.4(b)(1)(ii) provides that if a carpet or rug has had a fire-retardant treatment, or is made of fibers which have had a fire-retardant treatment, the sample or oversized... specimens either 10 times under the washing and drying procedure prescribed in Method 124-1996 of the...

16 CFR 1630.63 - Suspension of washing requirements for carpets and rugs with alumina trihydrate in the backing.

Code of Federal Regulations, 2014 CFR

2014-01-01

... of Carpets and Rugs (FF 1-70) at § 1630.4(b)(1)(ii) provides that if a carpet or rug has had a fire-retardant treatment, or is made of fibers which have had a fire-retardant treatment, the sample or oversized... specimens either 10 times under the washing and drying procedure prescribed in Method 124-1996 of the...

16 CFR 1630.63 - Suspension of washing requirements for carpets and rugs with alumina trihydrate in the backing.

Code of Federal Regulations, 2011 CFR

2011-01-01

... of Carpets and Rugs (FF 1-70) at § 1630.4(b)(1)(ii) provides that if a carpet or rug has had a fire-retardant treatment, or is made of fibers which have had a fire-retardant treatment, the sample or oversized... specimens either 10 times under the washing and drying procedure prescribed in Method 124-1996 of the...

16 CFR § 1630.63 - Suspension of washing requirements for carpets and rugs with alumina trihydrate in the backing.

Code of Federal Regulations, 2013 CFR

2013-01-01

... of Carpets and Rugs (FF 1-70) at § 1630.4(b)(1)(ii) provides that if a carpet or rug has had a fire-retardant treatment, or is made of fibers which have had a fire-retardant treatment, the sample or oversized... specimens either 10 times under the washing and drying procedure prescribed in Method 124-1996 of the...

Identification of registered nursing care of residents in English nursing homes using the Minimum Data Set Resident Assessment Instrument (MDS/RAI) and Resource Utilisation Groups version III (RUG-III).

PubMed

Carpenter, Iain; Perry, Michelle; Challis, David; Hope, Kevin

2003-05-01

to determine if a combination of Minimum Data Set/Resident Assessment Instrument (MDS/RAI) assessment variables and the Resource Utilisation Groups version III (RUG-III) case-mix system could be used as a method of identifying and reimbursing registered nursing care needs in long-term care. the sample included 193 nursing home residents from four nursing homes from three different locations and care providers in England. The study included assessments of residents' care needs using either the MDS/RAI assessments or RUG stand-alone questionnaires and a time study that recorded the amount of nursing time received by residents over a 24-h period. Validity of RUG-III for explaining the distribution of care time between residents in different RUG-III groups was tested. The difference in direct and indirect care provided by registered general nurses (RGN) and care assistants (CA) to residents in RUG-III clinical groups was compared. the RUG-III system explained 56% of the variance in care time (Eta2, P=0.0001). Residents in RUG-III groups associated with particular medical and nursing needs (enhanced RGN care) received more than twice as much indirect RGN care time (t-test, P<0.001) and 1.4 times as much direct RGN and direct CA time (t-test, P<0.01) than residents with primarily cognitive impairment or physical problems only (standard RGN care). Residents with enhanced RGN care received an average of 48.1 min of RGN care in 24 h (95% CI 4.1-55.2) compared with an average of 31.1 min (95% CI 26.8-35.5) for residents in the standard RGN care group. A third low RGN care group was created following publication of the Department of Health guidance on NHS Funded Nursing Care. With three levels, the enhanced care group receives about 38% more than the standard group, and the low group receives about 50% of the standard group. the RUG-III system effectively differentiated between nursing home residents who are receiving 'low', 'standard' and 'enhanced' RGN care time. The findings could provide the basis of a reimbursement system for registered nursing time in long-term care facilities in the UK.

Removal of Covalent Heterogeneity Reveals Simple Folding Behavior for P4-P6 RNA*

PubMed Central

Greenfeld, Max; Solomatin, Sergey V.; Herschlag, Daniel

2011-01-01

RNA folding landscapes have been described alternately as simple and as complex. The limited diversity of RNA residues and the ability of RNA to form stable secondary structures prior to adoption of a tertiary structure would appear to simplify folding relative to proteins. Nevertheless, there is considerable evidence for long-lived misfolded RNA states, and these observations have suggested rugged energy landscapes. Recently, single molecule fluorescence resonance energy transfer (smFRET) studies have exposed heterogeneity in many RNAs, consistent with deeply furrowed rugged landscapes. We turned to an RNA of intermediate complexity, the P4-P6 domain from the Tetrahymena group I intron, to address basic questions in RNA folding. P4-P6 exhibited long-lived heterogeneity in smFRET experiments, but the inability to observe exchange in the behavior of individual molecules led us to probe whether there was a non-conformational origin to this heterogeneity. We determined that routine protocols in RNA preparation and purification, including UV shadowing and heat annealing, cause covalent modifications that alter folding behavior. By taking measures to avoid these treatments and by purifying away damaged P4-P6 molecules, we obtained a population of P4-P6 that gave near-uniform behavior in single molecule studies. Thus, the folding landscape of P4-P6 lacks multiple deep furrows that would trap different P4-P6 molecules in different conformations and contrasts with the molecular heterogeneity that has been seen in many smFRET studies of structured RNAs. The simplicity of P4-P6 allowed us to reliably determine the thermodynamic and kinetic effects of metal ions on folding and to now begin to build more detailed models for RNA folding behavior. PMID:21478155

Classification of residents in nursing homes in Tuscany (Italy) using Resource Utilization Groups Version III (RUG-III).

PubMed

Francesconi, Paolo; Cantini, Elisabetta; Bavazzano, Emanuela; Lauretani, Fabrizio; Bandinelli, Stefania; Buiatti, Eva; Ferrucci, Luigi

2006-04-01

Samples of nursing homes in Tuscany (Italy) classify their residents and determine their case-mix according to the Resource Utilization Groups System, Version III (RUG-III). A large sample of nursing homes was selected, based on willingness to participate, representation of both public and private institutions, and wide geographic representation. Two registered nurses assessed all residents using the RUG questionnaire. The information collected was then used to group residents into 44 RUGs, and facility-specific case-mix indices were calculated using the RUG-specific weights previously validated in Italy. A total of 3981 residents from 93 nursing homes were assessed. Most residents were over 75 years old (87.4%) and women (68.6%). A large percentage was classified into RUGs within the following primary categories: reduced physical function (33.6%), impaired cognition (17.6%) and clinically complex (17.6%). The resulting nursing home case-mix indices ranged from 0.627 to 1.108 (mean 0.807+/-0.110). No significant association was found between type of facility, level of fees, or extent of staff in the nursing homes and their case-mix indices. RUGIII can provide information on types of nursing home residents and their care needs. This is useful for monitoring and evaluating long-term care services for the elderly, and allows for more effective planning and allocation of staffing and financial resources.

Rugged, Low Cost, Environmental Sensors for a Turbulent World

NASA Astrophysics Data System (ADS)

Schulz, B.; Sandell, C. T.; Wickert, A. D.

2017-12-01

Ongoing scientific research and resource management require a diverse range of high-quality and low-cost sensors to maximize the number and type of measurements that can be obtained. To accomplish this, we have developed a series of diversified sensors for common environmental applications. The TP-DownHole is an ultra-compact temperature and pressure sensor designed for use in CMT (Continuous Multi-channel Tubing) multi-level wells. Its 1 mm water depth resolution, 30 cm altitude resolution, and rugged design make it ideal for both water level measurements and monitoring barometric pressure and associated temperature changes. The TP-DownHole sensor has also been incorporated into a self-contained, fully independent data recorder for extreme and remote environments. This device (the TP-Solo) is based around the TP-DownHole design, but has self-contained power and data storage and is designed to collect data independently for up to 6 months (logging at once an hour), creating a specialized tool for extreme environment data collection. To gather spectral information, we have also developed a very low cost photodiode-based Lux sensor to measure spectral irradiance; while this does not measure the entire solar radiation spectrum, simple modeling to rescale the remainder of the solar spectrum makes this a cost-effective alternative to a thermopile pyranometer. Lastly, we have developed an instrumentation amplifier which is designed to interface a wide range of sensitive instruments to common data logging systems, such as thermopile pyranometers, thermocouples, and many other analog output sensors. These three instruments are the first in a diverse family aimed to give researchers a set of powerful and low-cost tools for environmental instrumentation.

Anomalous dimensionality dependence of diffusion in a rugged energy landscape: How pathological is one dimension?

NASA Astrophysics Data System (ADS)

Seki, Kazuhiko; Bagchi, Kaushik; Bagchi, Biman

2016-05-01

Diffusion in one dimensional rugged energy landscape (REL) is predicted to be pathologically different (from any higher dimension) with a much larger chance of encountering broken ergodicity [D. L. Stein and C. M. Newman, AIP Conf. Proc. 1479, 620 (2012)]. However, no quantitative study of this difference has been reported, despite the prevalence of multidimensional physical models in the literature (like a high dimensional funnel guiding protein folding/unfolding). Paradoxically, some theoretical studies of these phenomena still employ a one dimensional diffusion description for analytical tractability. We explore the dimensionality dependent diffusion on REL by carrying out an effective medium approximation based analytical calculations and compare them with the available computer simulation results. We find that at an intermediate level of ruggedness (assumed to have a Gaussian distribution), where diffusion is well-defined, the value of the effective diffusion coefficient depends on dimensionality and changes (increases) by several factors (˜5-10) in going from 1d to 2d. In contrast, the changes in subsequent transitions (like 2d to 3d and 3d to 4d and so on) are far more modest, of the order of 10-20% only. When ruggedness is given by random traps with an exponential distribution of barrier heights, the mean square displacement (MSD) is sub-diffusive (a well-known result), but the growth of MSD is described by different exponents in one and higher dimensions. The reason for such strong ruggedness induced retardation in the case of one dimensional REL is discussed. We also discuss the special limiting case of infinite dimension (d = ∞) where the effective medium approximation becomes exact and where theoretical results become simple. We discuss, for the first time, the role of spatial correlation in the landscape on diffusion of a random walker.

Anomalous dimensionality dependence of diffusion in a rugged energy landscape: How pathological is one dimension?

PubMed

Seki, Kazuhiko; Bagchi, Kaushik; Bagchi, Biman

2016-05-21

Diffusion in one dimensional rugged energy landscape (REL) is predicted to be pathologically different (from any higher dimension) with a much larger chance of encountering broken ergodicity [D. L. Stein and C. M. Newman, AIP Conf. Proc. 1479, 620 (2012)]. However, no quantitative study of this difference has been reported, despite the prevalence of multidimensional physical models in the literature (like a high dimensional funnel guiding protein folding/unfolding). Paradoxically, some theoretical studies of these phenomena still employ a one dimensional diffusion description for analytical tractability. We explore the dimensionality dependent diffusion on REL by carrying out an effective medium approximation based analytical calculations and compare them with the available computer simulation results. We find that at an intermediate level of ruggedness (assumed to have a Gaussian distribution), where diffusion is well-defined, the value of the effective diffusion coefficient depends on dimensionality and changes (increases) by several factors (∼5-10) in going from 1d to 2d. In contrast, the changes in subsequent transitions (like 2d to 3d and 3d to 4d and so on) are far more modest, of the order of 10-20% only. When ruggedness is given by random traps with an exponential distribution of barrier heights, the mean square displacement (MSD) is sub-diffusive (a well-known result), but the growth of MSD is described by different exponents in one and higher dimensions. The reason for such strong ruggedness induced retardation in the case of one dimensional REL is discussed. We also discuss the special limiting case of infinite dimension (d = ∞) where the effective medium approximation becomes exact and where theoretical results become simple. We discuss, for the first time, the role of spatial correlation in the landscape on diffusion of a random walker.

Using the RUG-III classification system for understanding the resource intensity of persons with intellectual disability residing in nursing homes.

PubMed

Martin, Lynn; Fries, Brant E; Hirdes, John P; James, Mary

2011-06-01

Since 1991, the Minimum Data Set 2.0 (MDS 2.0) has been the mandated assessment in US nursing homes. The Resource Utilization Groups III (RUG-III) case-mix system provides person-specific means of allocating resources based on the variable costs of caring for persons with different needs. Retrospective analyses of data collected on a sample of 9707 nursing home residents (2.4% had an intellectual disability) were used to examine the fit of the RUG-III case-mix system for determining the cost of supporting persons with intellectual disability (intellectual disability). The RUG-III system explained 33.3% of the variance in age-weighted nursing time among persons with intellectual disability compared to 29.6% among other residents, making it a good fit among persons with intellectual disability in nursing homes. The RUG-III may also serve as the basis for the development of a classification system that describes the resource intensity of persons with intellectual disability in other settings that provide similar types of support.

Proceedings of a pressure transducer-packer workshop, June 25-28, 1991

USGS Publications Warehouse

Latkovich, V. J.

1993-01-01

The U.S. Geological Survey conducted its first Pressure Transducer-Packer Workshop in Denver, Colorado, June 25-28, 1991. Nineteen attendees from the Survey, Environment Canada, academia, and the private sector presented papers concerning their experiences with the use of transducers and packers in hydrogeologic investigations. Workshop partici- pants concluded that fixed-head packers are generally more reliable than other types and that there is a need for a wet/wet transducer for deep wells. The group recommended that simple downhole technology be used, that only rugged commercially available packers be purchased, and that it is imperative electrical connections and transducer electronics be kept dry. (USGS)

Biased Metropolis Sampling for Rugged Free Energy Landscapes

NASA Astrophysics Data System (ADS)

Berg, Bernd A.

2003-11-01

Metropolis simulations of all-atom models of peptides (i.e. small proteins) are considered. Inspired by the funnel picture of Bryngelson and Wolyness, a transformation of the updating probabilities of the dihedral angles is defined, which uses probability densities from a higher temperature to improve the algorithmic performance at a lower temperature. The method is suitable for canonical as well as for generalized ensemble simulations. A simple approximation to the full transformation is tested at room temperature for Met-Enkephalin in vacuum. Integrated autocorrelation times are found to be reduced by factors close to two and a similar improvement due to generalized ensemble methods enters multiplicatively.

Evaluation of the feasibility of using the data collection system to operate a network of hydrological and climatological stations at sites remote from normal communication links

NASA Technical Reports Server (NTRS)

Perrier, R. (Principal Investigator)

1974-01-01

The author has identified the following significant results. The General Electric DCP has proven to be a versatile, rugged piece of hardware and has surpassed original expectation; it is very simple to use and does not require skilled staff for its use, installation, and operation. It is well suited for use in remote sites where no power is available. From this experience, it is concluded that the data collection system will be very useful in operating a network of hydrometeorological stations situated in sites remote from normal communication links.

Rugged passively cooled high power laser fiber optic connectors and methods of use

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rinzler, Charles C.; Gray, William C.; Fraze, Jason D.

2016-06-07

There are provided high power laser connectors and couplers and methods that are capable of providing high laser power without the need for active cooling to remote, harsh and difficult to access locations and under difficult and harsh conditions and to manage and mitigate the adverse effects of back reflections.

Measurement of the line-of-sight velocity of high-altitude barium clouds A technique

NASA Technical Reports Server (NTRS)

Mende, S. B.; Harris, S. E.

1982-01-01

It is demonstrated that for maximizing the scientific output of future ionospheric and magnetospheric ion cloud release experiments a new type of instrument is required which will measure the line-of-sight velocity of the ion cloud by the Doppler technique. A simple instrument was constructed using a 5-cm diam solid Fabry-Perot etalon coupled to a low-light-level integrating TV camera. It was demonstrated that the system has both the sensitivity and spectral resolution for detection of ion clouds and measurement of their line-of-sight Doppler velocity. The tests consisted of (1) a field experiment using a rocket barium cloud release to check sensitivity, and (2) laboratory experiments to show the spectral resolving capabilities of the system. The instrument was found to be operational if the source was brighter than approximately 1 kR, and it had a wavelength resolution much better than 0.2 A, which corresponds to approximately 12 km/sec or in the case of barium ion an acceleration potential of 100 V. The instrument is rugged and, therefore, simple to use in field experiments or on flight instruments. The sensitivity limit of the instrument can be increased by increasing the size of the etalon.

Validation of Resource Utilization Groups version III for Home Care (RUG-III/HC): evidence from a Canadian home care jurisdiction.

PubMed

Poss, Jeffrey W; Hirdes, John P; Fries, Brant E; McKillop, Ian; Chase, Mary

2008-04-01

The case-mix system Resource Utilization Groups version III for Home Care (RUG-III/HC) was derived using a modest data sample from Michigan, but to date no comprehensive large scale validation has been done. This work examines the performance of the RUG-III/HC classification using a large sample from Ontario, Canada. Cost episodes over a 13-week period were aggregated from individual level client billing records and matched to assessment information collected using the Resident Assessment Instrument for Home Care, from which classification rules for RUG-III/HC are drawn. The dependent variable, service cost, was constructed using formal services plus informal care valued at approximately one-half that of a replacement worker. An analytic dataset of 29,921 episodes showed a skewed distribution with over 56% of cases falling into the lowest hierarchical level, reduced physical functions. Case-mix index values for formal and informal cost showed very close similarities to those found in the Michigan derivation. Explained variance for a function of combined formal and informal cost was 37.3% (20.5% for formal cost alone), with personal support services as well as informal care showing the strongest fit to the RUG-III/HC classification. RUG-III/HC validates well compared with the Michigan derivation work. Potential enhancements to the present classification should consider the large numbers of undifferentiated cases in the reduced physical function group, and the low explained variance for professional disciplines.

Simultaneous and rapid determination of deoxynivalenol and its acetylate derivatives in wheat flour and rice by ultra high performance liquid chromatography with photo diode array detection.

PubMed

Xu, Jiao-Jiao; Zhou, Jian; Huang, Bai-Fen; Cai, Zeng-Xuan; Xu, Xiao-Min; Ren, Yi-Ping

2016-06-01

A simple and reliable method of ultra high performance liquid chromatography coupled with photo-diode array detection has been proposed for the simultaneous determination of deoxynivalenol and its acetylated derivatives in wheat flour and rice, especially focusing on the optimization of sample extraction, cleanup, and chromatographic separation conditions. Sample pretreatment consisted of a first step using a quick, easy, cheap, effective, rugged, and safe based extraction procedure and a subsequent cleanup step based on solid-phase extraction. The method was extensively validated in wheat flour and rice, obtaining satisfactory analytical performance with good linearity (R(2) ≥ 0.999), acceptable recoveries (80.0-104.4%), and repeatability (RSDs 1.3-10.7%). The limits of detection (21.7-57.4 μg/kg) and quantitation (72.3-191.4 μg/kg) for deoxynivalenols were lower than those usually permitted by various countries' legislation in these food matrices. The method was applied to 34 wheat and rice samples. The results were further compared with results of ultra high performance liquid chromatography with electrospray ionization tandem mass spectrometry. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Nursing home case-mix instruments: validation of the RUG-III system in Italy.

PubMed

Brizioli, Enrico; Bernabei, Roberto; Grechi, Francesca; Masera, Filippo; Landi, Francesco; Bandinelli, Stefania; Cavazzini, Chiara; Gangemi, Salvatore; Ferrucci, Luigi

2003-06-01

The current Italian reimbursement system for long-term care does not adequately consider the great variability in the health and functional status of older persons who are admitted to long-term care institutions. Furthermore, no procedure is implemented to monitor the quality of care provided to older residents. We conducted this study to verify whether the RUG-III (Resource Utilization Groups-version III), a tool for assessing the case-mix of nursing home residents, which is widely used in the United States and in many European countries, can be effectively used in the Italian health care system. We administered an Italian version of the RUG-III to 1000 older residents of 11 intermediate- and long-term care institutions. We also collected objective information on the amount of care provided directly or indirectly to each resident by nurses, physical therapists, and other health professionals. The RUG-III 44 group classification system explained 61 and 44% of the variance in rehabilitative and nursing wage-adjusted care time, respectively. Our findings provide strong evidence that the RUG-III classification, applied to Italian intermediate- and long-term care institutions, provides a robust estimate of the amount of nursing and rehabilitation resources consumed by older residents.

Rugged large volume injection for sensitive capillary LC-MS environmental monitoring

NASA Astrophysics Data System (ADS)

Roberg-Larsen, Hanne; Abele, Silvija; Demir, Deniz; Dzabijeva, Diana; Amundsen, Sunniva F.; Wilson, Steven R.; Bartkevics, Vadims; Lundanes, Elsa

2017-08-01

A rugged and high throughput capillary column (cLC) LC-MS switching platform using large volume injection and on-line automatic filtration and filter back-flush (AFFL) solid phase extraction (SPE) for analysis of environmental water samples with minimal sample preparation is presented. Although narrow columns and on-line sample preparation are used in the platform, high ruggedness is achieved e.g. injection of 100 non-filtrated water samples would did not result in a pressure rise/clogging of the SPE/capillary columns (inner diameter 300 µm). In addition, satisfactory retention time stability and chromatographic resolution were also features of the system. The potential of the platform for environmental water samples was demonstrated with various pharmaceutical products, which had detection limits (LOD) in the 0.05 - 12.5 ng/L range. Between-day and within-day repeatability of selected analytes were < 20% RSD.

Analysis of organo-chlorine pesticides residue in raw coffee with a modified "quick easy cheap effective rugged and safe" extraction/clean up procedure for reducing the impact of caffeine on the gas chromatography-mass spectrometry measurement.

PubMed

Bresin, Bruno; Piol, Maria; Fabbro, Denis; Mancini, Maria Antonietta; Casetta, Bruno; Del Bianco, Clorinda

2015-01-09

The control of pesticide residues on raw coffee is a task of great importance due to high consumption of this beverage in Italy and in many other countries. High caffeine content can hamper extraction and measurement of any pesticide residue. A tandem extraction protocol has been devised by exploiting the quick easy cheap effective rugged and safe (QuEChERS) scheme for extraction, coupled to a dispersive liquid-liquid micro-extraction (DLLME) in order to drastically reduce caffeine content in the final extract. Gas chromatography-mass spectrometry (GC-MS) has been used for quantification of organo-chlorine pesticides in single ion monitoring (SIM) mode. Method has been validated and performances meet the criteria prescribed by European Union regulations. Copyright © 2014 Elsevier B.V. All rights reserved.

[On the Way to Culture-Sensitive Patient Information Materials: Results of a Focus Group Study].

PubMed

Ries, Zivile; Frank, Fabian; Bermejo, Isaac; Kalaitsidou, Chariklia; Zill, Jördis; Dirmaier, Jörg; Härter, Martin; Bengel, Jürgen; Hölzel, Lars

2018-06-01

This study was part of a double-blind randomised controlled trial aimed to evaluate the effects of culture-sensitive patient information materials (PIM) compared with standard translated material. The study aimed to obtain the data for the development of culture sensitive PIM about unipolar depression for the 4 largest migrant groups in Germany (Turkish, Polish, Russian and Italian migration background). A qualitative study using 4 manual-based focus groups (FG), one for each migrant group, with 29 participants (9 with a Turkish (TüG), 8 with a Polish (PoG), 5 with a Russian (RuG) and 7 with an Italian (ItG) migration background) was conducted. The discussions were recorded, transcribed and analyzed using qualitative content analysis. 7 categories were identified. For the (1.) development of a good culture-sensitive PIM an easy language, a clear structure, an assessable extent of information and the avoidance of stereotypes were highlighted cross-culturally in all four FG. RuG and PoG had the largest (2.) lack of information about the German health care system. Concerning the (3.) illness perception RuG named problems with recognizing and understanding depression. PoG, RuG and TüG thematized (4.) feared consequences of the illness and of professional helpseeking. ItG, PoG, RuG had fears concerning (5.) psychotropic drugs as a result from insufficient knowledge about medication. For (6.) doctor-patient relationship cultural specifics were identified in RuG and TüG and for (7.) migration or culture specific reasons for depression in RuG, ItG and TüG. Although the identified categories were relevant for all or for the majority of migrant groups, for most categories specific cultural aspects were discovered. These findings show the importance of a culture sensitive adaptation of PIM. © Georg Thieme Verlag KG Stuttgart · New York.

Perception for rugged terrain

NASA Technical Reports Server (NTRS)

Kweon, In SO; Hebert, Martial; Kanade, Takeo

1989-01-01

A three-dimensional perception system for building a geometrical description of rugged terrain environments from range image data is presented with reference to the exploration of the rugged terrain of Mars. An intermediate representation consisting of an elevation map that includes an explicit representation of uncertainty and labeling of the occluded regions is proposed. The locus method used to convert range image to an elevation map is introduced, along with an uncertainty model based on this algorithm. Both the elevation map and the locus method are the basis of a terrain matching algorithm which does not assume any correspondences between range images. The two-stage algorithm consists of a feature-based matching algorithm to compute an initial transform and an iconic terrain matching algorithm to merge multiple range images into a uniform representation. Terrain modeling results on real range images of rugged terrain are presented. The algorithms considered are a fundamental part of the perception system for the Ambler, a legged locomotor.

Best practices of MDOT's survey operation, organization and technology implementation.

DOT National Transportation Integrated Search

2012-05-01

A critical activity performed by employees of the Mississippi Department of Transportation is surveying. : Surveying in some instances needs to be performed in hazardous environments such as rugged terrain and : high-speed traffic. New surveying tech...

Connecting Fabric Families and Folk Art.

ERIC Educational Resources Information Center

Haussler-Mathews, Mary E.

2001-01-01

Discusses an art project in which students at the Quaker Farms School (Oxford, Connecticut) created a rag rug for the school bicentennial. Describes how the rag rug was created, stating that the students learned about their heritage in a cooperative way. (CMK)

Reuyl Crater Dust Avalanches

NASA Image and Video Library

2002-06-04

The rugged, arcuate rim of the 90 km crater Reuyl dominates this NASA Mars Odyssey image. Reuyl crater is at the southern edge of a region known to be blanketed in thick dust based on its high albedo brightness and low thermal inertia values.

Remote sensing for environmental protection of the eastern Mediterranean rugged mountainous areas, Lebanon

NASA Astrophysics Data System (ADS)

Khawlie, M.; Awad, M.; Shaban, A.; Bou Kheir, R.; Abdallah, C.

Lying along the eastern Mediterranean coast with elevated mountain chains higher than 2500 m straddling its terrain, Lebanon is a country of natural beauty and is thus attracting tourism. However, with a population density exceeding 800/km 2 and a rugged steep sloping land, problems abound in the country calling for holistic-approach studies. Only remote sensing, whose use is new in Lebanon can secure such needed studies within a scientific and pragmatic framework. The paper demonstrates for the concerned themes, the innovative use of remote sensing in such a difficult terrain, giving three examples of major environmental problems in the coastal mountains. Only few studies have so far focused on those mountains, notably application of remote sensing. The rugged mountainous terrain receives considerable rain, but the water is quickly lost running on the steep slopes, or infiltrating through fractures and the karstic conduits into the subsurface. Field investigations are difficult to achieve, therefore, remote sensing helps reveal various surface land features important in reflecting water feeding into the subsurface. Optical, radar and thermal infrared remotely sensed data cover a wide spectrum serving that purpose. A map of preferential groundwater accumulation potential is produced. It can serve for better water exploitation as well as protection. Because the terrain is karstic and rugged, the subsurface water flow is difficult to discern. Any pollution at a certain spot would certainly spread around. This constitutes the second example of environmental problems facing the mountainous areas in Lebanon. An integrated approach using remote sensing and geographic information systems (GIS) gives good results in finding out the likelihood of how pollution, or contaminants, can selectively move in the subsurface. A diagnostic analysis with a GIS-type software acts as a guide producing indicative maps for the above purpose. The third example given deals with the problem of losing soil, which is a very vital source in such mountainous land. With steep slopes, torrential rain and improper human interference, run-off is high and water-soil erosion is continuously deteriorating the land cover. Remote sensing can facilitate studying the factors enhancing the process, such as soil type, slope gradient, drainage, geology and land cover. Digital elevation models created from SAR imagery contribute significantly to assessing vulnerability of hydric-soil erosion over such a difficult terrain. GIS layers of the above factors are integrated with erosional criteria to produce a risk map of soil erosion. Results indicate that 36% of the Lebanese terrain is under threat of high-level erosion, and 52% of that is concentrated in the rugged mountainous regions.

Two-dimensional photon-counting detector arrays based on microchannel array plates

NASA Technical Reports Server (NTRS)

Timothy, J. G.; Bybee, R. L.

1975-01-01

The production of simple and rugged photon-counting detector arrays has been made possible by recent improvements in the performance of the microchannel array plate (MCP) and by the parallel development of compatible electronic readout systems. The construction of proximity-focused MCP arrays of novel design in which photometric information from (n x m) picture elements is read out with a total of (n + m) amplifier and discriminator circuits is described. Results obtained with a breadboard (32 x 32)-element array employing 64 charge-sensitive amplifiers are presented, and the application of systems of this type in spectrometers and cameras for use with ground-based telescopes and on orbiting spacecraft discussed.

Low-Power Architecture for an Optical Life Gas Analyzer

NASA Technical Reports Server (NTRS)

Pilgrim, Jeffrey; Vakhtin, Andrei

2012-01-01

Analog and digital electronic control architecture has been combined with an operating methodology for an optical trace gas sensor platform that allows very low power consumption while providing four independent gas measurements in essentially real time, as well as a user interface and digital data storage and output. The implemented design eliminates the cross-talk between the measurement channels while maximizing the sensitivity, selectivity, and dynamic range for each measured gas. The combination provides for battery operation on a simple camcorder battery for as long as eight hours. The custom, compact, rugged, self-contained design specifically targets applications of optical major constituent and trace gas detection for multiple gases using multiple lasers and photodetectors in an integrated package.

Closer Look: Majestic Mountains and Frozen Plains

NASA Image and Video Library

2015-09-17

Just 15 minutes after its closest approach to Pluto on July 14, 2015, NASA's New Horizons spacecraft looked back toward the sun and captured a near-sunset view of the rugged, icy mountains and flat ice plains extending to Pluto's horizon. The smooth expanse of the informally named Sputnik Planum (right) is flanked to the west (left) by rugged mountains up to 11,000 feet (3,500 meters) high, including the informally named Norgay Montes in the foreground and Hillary Montes on the skyline. The backlighting highlights more than a dozen layers of haze in Pluto's tenuous but distended atmosphere. The image was taken from a distance of 11,000 miles (18,000 kilometers) to Pluto; the scene is 230 miles (380 kilometers) across. http://photojournal.jpl.nasa.gov/catalog/PIA19947

X-ray Device Makes Scrubbing Rugs Clean a Spotless Effort

NASA Technical Reports Server (NTRS)

2006-01-01

If "pulling the rug out from under" means suddenly withdrawing support and assistance, then NASA is pretty good at "putting the rug under" when it comes to offering technical support and assistance to private industry. In the case of a new X-ray fluorescence (XRF) sensor featuring enhancements compliments of NASA, the Space Agency not only provided the rug, but helped give private industry a means to ensure it keeps clean. This sensor, utilized by NASA to read chemical bar codes concealed by paint and other coatings, perform on-the-spot chemical analyses in field conditions, and detect difficult-to-identify contaminants, has found another use as a tool that can measure how much soil is removed from household and commercial carpets. The original technology was developed in 2002 to conduct quality control for critical aluminum alloy parts destined for the space shuttle. Evaluation of these parts is critical for the Space Agency, as any signs of contamination, corrosion, or material deviation could compromise a shuttle mission.

Rugged Metropolis sampling with simultaneous updating of two dynamical variables

NASA Astrophysics Data System (ADS)

Berg, Bernd A.; Zhou, Huan-Xiang

2005-07-01

The rugged Metropolis (RM) algorithm is a biased updating scheme which aims at directly hitting the most likely configurations in a rugged free-energy landscape. Details of the one-variable (RM1) implementation of this algorithm are presented. This is followed by an extension to simultaneous updating of two dynamical variables (RM2) . In a test with the brain peptide Met-Enkephalin in vacuum RM2 improves conventional Metropolis simulations by a factor of about 4. Correlations between three or more dihedral angles appear to prevent larger improvements at low temperatures. We also investigate a multihit Metropolis scheme, which spends more CPU time on variables with large autocorrelation times.

Control and Analysis for a Self-Excited Induction Generator for Wind Turbine and Electrolyzer Applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Muljadi, Eduard; Na, Woonki; Leighty, Bill

Self-Excited Induction Generation(SEIG) is very rugged, simple, lightweight, and it is easy and inexpensive to implement, very simple to control, and requires a very little maintenance. In this variable-speed operation, the SEIG needs a power electronics interface to convert from the variable frequency output voltage of the generator to a DC output voltage for battery or other DC applications. In our study, a SEIG is connected to the power electronics interface such as diode rectifier and DC/DC converter and then an electrolyzer is connected as a final DC load for fuel cell applications. An equivalent circuit model for an electrolyzermore » is utilized for our application. The control and analysis for the proposed system is carried out by using PSCAD and MATLAB software. This study would be useful for designing and control analysis of power interface circuits for SEIG for a variable speed wind turbine generation with fuel cell applications before the actual implementation.« less

Stable and rugged etalon for the Dynamics Explorer Fabry-Perot interferometer. I - Design and construction

NASA Astrophysics Data System (ADS)

Rees, D.; Fuller-Rowell, T. J.; Lyons, A.; Killeen, T. L.; Hays, P. B.

1982-11-01

The cemented etalons are shown to be rugged and highly stable for high-resolution spectroscopy and to be well suited to space applications. The etalons will be of considerable value as the tuning elements of dye laser systems and as the stable spectral disperser for pulse and CW laser spectroscopy. Even for etalons 15 cm in diameter, the strength of the cemented bond is greatly in excess of the maximum steady and impulsive forces experienced from the much larger etalon plate mass (2-4 kg rather than 200 g). It is thought that the small but systematic and significant positive increment in the thermal expansion coefficient which occurs when an etalon and its spacers are cemented may be linked to the cessation of the microscopic migration that occurs with an optically contacted bond under thermal or mechanical stress. The etalon comprises two flat plates of fused silica, with spacers constructed of Zerodur (a polycrystalline glass ceramic of extremely low expansion coefficient) which are cemented together using cyanoacrylic adhesives.

The Goat in the Rug.

ERIC Educational Resources Information Center

Blood, Charles L.; Link, Martin

Based on the activities of the real Window Rock weaver, Glenmae, and her goat, Geraldine, this illustrated story incorporates authentic details relative to the Navajo art of rug weaving and is designed for children aged four to eight. Capitalizing on the humor inherent in Geraldine's point of view, the story centers on the goat's observation of…

Rugged microelectronic module package supports circuitry on heat sink

NASA Technical Reports Server (NTRS)

Johnson, A. L.

1966-01-01

Rugged module package for thin film hybrid microcircuits incorporated a rigid, thermally conductive support structure, which serves as a heat sink, and a lead wire block in which T-shaped electrical connectors are potted. It protects the circuitry from shock and vibration loads, dissipates internal heat, and simplifies electrical connections between adjacent modules.

46 CFR 116.423 - Furniture and furnishings.

Code of Federal Regulations, 2014 CFR

2014-10-01

... Systems Using a Radiant Heat Energy Source,” and with a specific optical density not to exceed 450 in both...) “Specific Optical Density of Smoke generated by Solid Materials.” Also: (i) Rugs and carpets shall not extend up bulkheads or vertical surfaces more than 10 centimeters (4 inches) above the deck. (ii) Rugs...

46 CFR 116.423 - Furniture and furnishings.

Code of Federal Regulations, 2012 CFR

2012-10-01

... Systems Using a Radiant Heat Energy Source,” and with a specific optical density not to exceed 450 in both...) “Specific Optical Density of Smoke generated by Solid Materials.” Also: (i) Rugs and carpets shall not extend up bulkheads or vertical surfaces more than 10 centimeters (4 inches) above the deck. (ii) Rugs...

46 CFR 116.423 - Furniture and furnishings.

Code of Federal Regulations, 2013 CFR

2013-10-01

... Systems Using a Radiant Heat Energy Source,” and with a specific optical density not to exceed 450 in both...) “Specific Optical Density of Smoke generated by Solid Materials.” Also: (i) Rugs and carpets shall not extend up bulkheads or vertical surfaces more than 10 centimeters (4 inches) above the deck. (ii) Rugs...

Key issues review: evolution on rugged adaptive landscapes

NASA Astrophysics Data System (ADS)

Obolski, Uri; Ram, Yoav; Hadany, Lilach

2018-01-01

Adaptive landscapes represent a mapping between genotype and fitness. Rugged adaptive landscapes contain two or more adaptive peaks: allele combinations with higher fitness than any of their neighbors in the genetic space. How do populations evolve on such rugged landscapes? Evolutionary biologists have struggled with this question since it was first introduced in the 1930s by Sewall Wright. Discoveries in the fields of genetics and biochemistry inspired various mathematical models of adaptive landscapes. The development of landscape models led to numerous theoretical studies analyzing evolution on rugged landscapes under different biological conditions. The large body of theoretical work suggests that adaptive landscapes are major determinants of the progress and outcome of evolutionary processes. Recent technological advances in molecular biology and microbiology allow experimenters to measure adaptive values of large sets of allele combinations and construct empirical adaptive landscapes for the first time. Such empirical landscapes have already been generated in bacteria, yeast, viruses, and fungi, and are contributing to new insights about evolution on adaptive landscapes. In this Key Issues Review we will: (i) introduce the concept of adaptive landscapes; (ii) review the major theoretical studies of evolution on rugged landscapes; (iii) review some of the recently obtained empirical adaptive landscapes; (iv) discuss recent mathematical and statistical analyses motivated by empirical adaptive landscapes, as well as provide the reader with instructions and source code to implement simulations of evolution on adaptive landscapes; and (v) discuss possible future directions for this exciting field.

Pressure Measurement Sensor

NASA Technical Reports Server (NTRS)

1997-01-01

FFPI Industries Inc. is the manufacturer of fiber-optic sensors that furnish accurate pressure measurements in internal combustion chambers. Such an assessment can help reduce pollution emitted by these engines. A chief component in the sensor owes its seven year- long development to Lewis Research Center funding to embed optical fibers and sensors in metal parts. NASA support to Texas A&M University played a critical role in developing this fiber optic technology and led to the formation of FFPI Industries and the production of fiber sensor products. The simple, rugged design of the sensor offers the potential for mass production at low cost. Widespread application of the new technology is forseen, from natural gas transmission, oil refining and electrical power generation to rail transport and the petrochemical paper product industry.

REFRIGERATION ESPECIALLY FOR VERY LOW TEMPERATURES

DOEpatents

Kennedy, P.B.; Smith, H.R. Jr.

1960-09-13

A refrigeration system for producing very low temperatures is described. The system of the invention employs a binary mixture refrigerant in a closed constant volume, e.g., Freon and ethylene. Such mixture is compressed in the gaseous state and is then separated in a fractionating column element of the system. Thenceforth, the first liquid to separate is employed stagewise to cool and liq uefy successive portions of the refrigerant at successively lower temperatures by means of heat exchangers coupled between the successive stages. When shut down, all of the volumes of the system are interconnected and a portion of the refrigerant remains liquid at ambient temperatures so that no dangerous overpressures develop. The system is therefore rugged, simple and dependable in operation.

Development of LC/MS/MS Methods for Implementation in US EPA’s Drinking Water Unregulated Contaminant Monitoring Regulations

EPA Science Inventory

Well-characterized and standardized methods are the foundation upon which monitoring of regulated and unregulated contaminants in drinking water are based. To obtain reliable, high quality data for trace analysis of contaminants, these methods must be rugged, selective and sensit...

ACCESS America's great outdoors: public lands are for everyone!

Treesearch

Joe Meade; Gregory J. Lais

1995-01-01

With nearly 200 million acres of majestic mountains, deep rugged canyons, pristine high lakes, wild rivers, immense forests, and open meadows, the National Forest System provides the largest variety of outdoor recreation opportunities in the United States. Federal lands encompass a combined total of nearly one-third of this country.

16 CFR 1630.61 - Hide carpets and rugs-alternative washing procedure.

Code of Federal Regulations, 2010 CFR

2010-01-01

... normally used for that type of carpet or rug in service. (b) On February 10, 1972 (37 FR 3010) the Federal... 2″ in diameter and 9″ long composed of nonabsorbant material such as glass or plastic. (4) Select... remove all excess water and wrap around the operating applicator. (7) Immediately with light pressure...

16 CFR 1631.61 - Hide carpets and rugs-alternative washing procedure.

Code of Federal Regulations, 2010 CFR

2010-01-01

... normally used for that type of carpet or rug in service. (b) On February 10, 1972 (37 FR 3010) the Federal... 2″ in diameter and 9″ long composed of nonabsorbent material such as glass or plastic. (4) Select... remove all excess water and wrap around the operating applicator. (7) Immediately, with light pressure...

16 CFR 1630.61 - Hide carpets and rugs-alternative washing procedure.

Code of Federal Regulations, 2011 CFR

2011-01-01

... natural “lay” of the hair structure for ten complete strokes. (8) Place test specimen in a circulating... procedure under FF 1-70 for testing the flammability of shearling and hide rugs that (1) consist of natural wool or hair attached to the hide with no synthetic fibers and (2) have been treated with a fire...

16 CFR 1630.61 - Hide carpets and rugs-alternative washing procedure.

Code of Federal Regulations, 2014 CFR

2014-01-01

... natural “lay” of the hair structure for ten complete strokes. (8) Place test specimen in a circulating... procedure under FF 1-70 for testing the flammability of shearling and hide rugs that (1) consist of natural wool or hair attached to the hide with no synthetic fibers and (2) have been treated with a fire...

16 CFR 1630.61 - Hide carpets and rugs-alternative washing procedure.

Code of Federal Regulations, 2012 CFR

2012-01-01

... natural “lay” of the hair structure for ten complete strokes. (8) Place test specimen in a circulating... procedure under FF 1-70 for testing the flammability of shearling and hide rugs that (1) consist of natural wool or hair attached to the hide with no synthetic fibers and (2) have been treated with a fire...

16 CFR 1631.61 - Hide carpets and rugs-alternative washing procedure.

Code of Federal Regulations, 2011 CFR

2011-01-01

... natural “lay” of the hair structure for ten complete strokes. (8) Place test specimen in a circulating... procedure under FF 2-70 for testing the flammability of shearling and hide rugs that (1) consist of natural wool or hair attached to the hide with no synthetic fibers and (2) have been treated with a fire...

16 CFR 1631.61 - Hide carpets and rugs-alternative washing procedure.

Code of Federal Regulations, 2014 CFR

2014-01-01

... natural “lay” of the hair structure for ten complete strokes. (8) Place test specimen in a circulating... procedure under FF 2-70 for testing the flammability of shearling and hide rugs that (1) consist of natural wool or hair attached to the hide with no synthetic fibers and (2) have been treated with a fire...

16 CFR 1631.61 - Hide carpets and rugs-alternative washing procedure.

Code of Federal Regulations, 2012 CFR

2012-01-01

... natural “lay” of the hair structure for ten complete strokes. (8) Place test specimen in a circulating... procedure under FF 2-70 for testing the flammability of shearling and hide rugs that (1) consist of natural wool or hair attached to the hide with no synthetic fibers and (2) have been treated with a fire...

75 FR 42315 - Third Party Testing for Certain Children's Products; Carpets and Rugs: Requirements for...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-07-21

... samples that are identical in all material respects to the product. The Commission also emphasizes that... Small Carpets and Rugs (FF 2-70). A true copy, in English, of the accreditation and scope documents... status must submit to the Commission copies, in English, of their training documents showing how...

16 CFR 1631.34 - Small carpets and rugs not meeting acceptance criterion.

Code of Federal Regulations, 2010 CFR

2010-01-01

... acceptance criterion of such standard, it shall, prior to its introduction into commerce, be legibly and.... DEPARTMENT OF COMMERCE STANDARD FF 2-70): SHOULD NOT BE USED NEAR SOURCES OF IGNITION.” The required... section, in addition to the label required to be affixed to the small carpets or rugs. (e) Where small...

Mathematics Student Teachers' Modelling Approaches While Solving the Designed Esme Rug Problem

ERIC Educational Resources Information Center

Hidiroglu, Çaglar Naci; Dede, Ayse Tekin; Ünver, Semiha Kula; Güzel, Esra Bukova

2017-01-01

The purpose of the study is to analyze the mathematics student teachers' solutions on the Esme Rug Problem through 7-stage mathematical modelling process. This problem was designed by the researchers by considering the modelling problems' main properties. The study was conducted with twenty one secondary mathematics student teachers. The data were…

Demersal fish assemblages on seamounts and other rugged features in the northeastern Caribbean

NASA Astrophysics Data System (ADS)

Quattrini, Andrea M.; Demopoulos, Amanda W. J.; Singer, Randal; Roa-Varon, Adela; Chaytor, Jason D.

2017-05-01

Recent investigations of demersal fish communities in deepwater (>50 m) habitats have considerably increased our knowledge of the factors that influence the assemblage structure of fishes across mesophotic to deep-sea depths. While different habitat types influence deepwater fish distribution, whether different types of rugged seafloor features provide functionally equivalent habitat for fishes is poorly understood. In the northeastern Caribbean, different types of rugged features (e.g., seamounts, banks, canyons) punctuate insular margins, and thus create a remarkable setting in which to compare demersal fish communities across various features. Concurrently, several water masses are vertically layered in the water column, creating strong stratification layers corresponding to specific abiotic conditions. In this study, we examined differences among fish assemblages across different features (e.g., seamount, canyon, bank/ridge) and water masses at depths ranging from 98 to 4060 m in the northeastern Caribbean. We conducted 26 remotely operated vehicle dives across 18 sites, identifying 156 species of which 42% of had not been previously recorded from particular depths or localities in the region. While rarefaction curves indicated fewer species at seamounts than at other features in the NE Caribbean, assemblage structure was similar among the different types of features. Thus, similar to seamount studies in other regions, seamounts in the Anegada Passage do not harbor distinct communities from other types of rugged features. Species assemblages, however, differed among depths, with zonation generally corresponding to water mass boundaries in the region. High species turnover occurred at depths <1200 m, and may be driven by changes in water mass characteristics including temperature (4.8-24.4 °C) and dissolved oxygen (2.2-9.5 mg per l). Our study suggests the importance of water masses in influencing community structure of benthic fauna, while considerably adding to the knowledge of mesophotic and deep-sea fish biogeography.

Demersal fish assemblages on seamounts and other rugged features in the northeastern Caribbean

USGS Publications Warehouse

Quattrini, Andrea M.; Demopoulos, Amanda W. J.; Singer, Randal; Roa-Varon, Adela; Chaytor, Jason D.

2017-01-01

Recent investigations of demersal fish communities in deepwater (>50 m) habitats have considerably increased our knowledge of the factors that influence the assemblage structure of fishes across mesophotic to deep-sea depths. While different habitat types influence deepwater fish distribution, whether different types of rugged seafloor features provide functionally equivalent habitat for fishes is poorly understood. In the northeastern Caribbean, different types of rugged features (e.g., seamounts, banks, canyons) punctuate insular margins, and thus create a remarkable setting in which to compare demersal fish communities across various features. Concurrently, several water masses are vertically layered in the water column, creating strong stratification layers corresponding to specific abiotic conditions. In this study, we examined differences among fish assemblages across different features (e.g., seamount, canyon, bank/ridge) and water masses at depths ranging from 98 to 4060 m in the northeastern Caribbean. We conducted 26 remotely operated vehicle dives across 18 sites, identifying 156 species of which 42% of had not been previously recorded from particular depths or localities in the region. While rarefaction curves indicated fewer species at seamounts than at other features in the NE Caribbean, assemblage structure was similar among the different types of features. Thus, similar to seamount studies in other regions, seamounts in the Anegada Passage do not harbor distinct communities from other types of rugged features. Species assemblages, however, differed among depths, with zonation generally corresponding to water mass boundaries in the region. High species turnover occurred at depths <1200 m, and may be driven by changes in water mass characteristics including temperature (4.8–24.4 °C) and dissolved oxygen (2.2–9.5 mg per l). Our study suggests the importance of water masses in influencing community structure of benthic fauna, while considerably adding to the knowledge of mesophotic and deep-sea fish biogeography.

Rugged, no-moving-parts windspeed and static pressure probe designs for measurements in planetary atmospheres

NASA Technical Reports Server (NTRS)

Bedard, A. J., Jr.; Nishiyama, R. T.

1993-01-01

Instruments developed for making meteorological observations under adverse conditions on Earth can be applied to systems designed for other planetary atmospheres. Specifically, a wind sensor developed for making measurements within tornados is capable of detecting induced pressure differences proportional to wind speed. Adding strain gauges to the sensor would provide wind direction. The device can be constructed in a rugged form for measuring high wind speeds in the presence of blowing dust that would clog bearings and plug passages of conventional wind speed sensors. Sensing static pressure in the lower boundary layer required development of an omnidirectional, tilt-insensitive static pressure probe. The probe provides pressure inputs to a sensor with minimum error and is inherently weather-protected. The wind sensor and static pressure probes have been used in a variety of field programs and can be adapted for use in different planetary atmospheres.

Pluto Majestic Mountains, Frozen Plains and Foggy Hazes

NASA Image and Video Library

2015-09-17

Just 15 minutes after its closest approach to Pluto on July 14, 2015, NASA's New Horizons spacecraft looked back toward the sun and captured this near-sunset view of the rugged, icy mountains and flat ice plains extending to Pluto's horizon. The smooth expanse of the informally named icy plain Sputnik Planum (right) is flanked to the west (left) by rugged mountains up to 11,000 feet (3,500 meters) high, including the informally named Norgay Montes in the foreground and Hillary Montes on the skyline. To the right, east of Sputnik, rougher terrain is cut by apparent glaciers. The backlighting highlights more than a dozen layers of haze in Pluto's tenuous but distended atmosphere. The image was taken from a distance of 11,000 miles (18,000 kilometers) to Pluto; the scene is 780 miles (1,250 kilometers) wide. http://photojournal.jpl.nasa.gov/catalog/PIA19948

Design and validation of a novel learning tool, the "Anato-Rug," for teaching equine topographical anatomy.

PubMed

Braid, Francesca; Williams, Sarah B; Weller, Renate

2012-01-01

Recognition of anatomical landmarks in live animals (and humans) is key for clinical practice, but students often find it difficult to translate knowledge from dissection-based anatomy onto the live animal and struggle to acquire this vital skill. The purpose of this study was to create and evaluate the use of an equine anatomy rug ("Anato-Rug") depicting topographical anatomy and key areas of lung, heart, and gastrointestinal auscultation, which could be used together with a live horse to aid learning of "live animal" anatomy. Over the course of 2 weeks, 38 third year veterinary students were randomly allocated into an experimental group, revising topographical anatomy from the "Anato-Rug," or a control group, learning topographical anatomy from a textbook. Immediately post activity, both groups underwent a test on live anatomy knowledge and were retested 1 week later. Both groups then completed a questionnaire to ascertain their perceptions of their learning experiences. Results showed that the experimental groups scored significantly higher than the control group at the first testing session, experienced more enjoyment during the activity and gained more confidence in identifying anatomical landmarks than the control group. There was not a significant difference in scores between groups at the second testing session. The findings indicate that the anatomy rug is an effective learning tool that aids understanding, confidence, and enjoyment in learning equine thorax and abdominal anatomy; however it was not better than traditional methods with regards to longer term memory recall. Copyright © 2012 American Association of Anatomists.

16 CFR § 1630.61 - Hide carpets and rugs-alternative washing procedure.

Code of Federal Regulations, 2013 CFR

2013-01-01

... natural “lay” of the hair structure for ten complete strokes. (8) Place test specimen in a circulating... procedure under FF 1-70 for testing the flammability of shearling and hide rugs that (1) consist of natural wool or hair attached to the hide with no synthetic fibers and (2) have been treated with a fire...

16 CFR § 1631.61 - Hide carpets and rugs-alternative washing procedure.

Code of Federal Regulations, 2013 CFR

2013-01-01

... natural “lay” of the hair structure for ten complete strokes. (8) Place test specimen in a circulating... procedure under FF 2-70 for testing the flammability of shearling and hide rugs that (1) consist of natural wool or hair attached to the hide with no synthetic fibers and (2) have been treated with a fire...

Rugged, Tunable Extended-Cavity Diode Laser

NASA Technical Reports Server (NTRS)

Moore, Donald; Brinza, David; Seidel, David; Klipstein, William; Choi, Dong Ho; Le, Lam; Zhang, Guangzhi; Iniguez, Roberto; Tang, Wade

2007-01-01

A rugged, tunable extended-cavity diode laser (ECDL) has been developed to satisfy stringent requirements for frequency stability, notably including low sensitivity to vibration. This laser is designed specifically for use in an atomic-clock experiment to be performed aboard the International Space Station (ISS). Lasers of similar design would be suitable for use in terrestrial laboratories engaged in atomic-clock and atomic-physics research.

[Study on the modeling of earth-atmosphere coupling over rugged scenes for hyperspectral remote sensing].

PubMed

Zhao, Hui-Jie; Jiang, Cheng; Jia, Guo-Rui

2014-01-01

Adjacency effects may introduce errors in the quantitative applications of hyperspectral remote sensing, of which the significant item is the earth-atmosphere coupling radiance. However, the surrounding relief and shadow induce strong changes in hyperspectral images acquired from rugged terrain, which is not accurate to describe the spectral characteristics. Furthermore, the radiative coupling process between the earth and the atmosphere is more complex over the rugged scenes. In order to meet the requirements of real-time processing in data simulation, an equivalent reflectance of background was developed by taking into account the topography and the geometry between surroundings and targets based on the radiative transfer process. The contributions of the coupling to the signal at sensor level were then evaluated. This approach was integrated to the sensor-level radiance simulation model and then validated through simulating a set of actual radiance data. The results show that the visual effect of simulated images is consistent with that of observed images. It was also shown that the spectral similarity is improved over rugged scenes. In addition, the model precision is maintained at the same level over flat scenes.

The resource utilization group system: its effect on nursing home case mix and costs.

PubMed

Thorpe, K E; Gertler, P J; Goldman, P

1991-01-01

Using data from 1985 and 1986, we examine how New York state's prospective payment system affected nursing homes. The system, called Resource Utilization Group (RUG-II), aimed to limit nursing home cost growth and improve access to nursing homes by "heavy-care" patients. As in Medicare's prospective hospital reimbursement system, payments to nursing homes were based on a "price," rather than facility-specific rates. With respect to cost growth, we observed considerable diversity among homes. Specifically, those nursing homes most financially constrained by the RUG-II methodology exhibited the slowest rates of cost growth; we observed higher cost growth among the homes least constrained. This higher rate of cost growth raises a question about the desirability of using a pricing methodology to determine nursing home payment rates. In addition to moderating cost growth, we also observed a significant change in the mix of patients admitted to nursing homes. During the first year of the RUG-II program, nursing homes admitted more heavy-care patients and reduced days of care to lighter-care patients. Thus, through 1986, the RUG-II program appeared to satisfy at least one of its major policy objectives.

Sampling in rugged terrain

USGS Publications Warehouse

Dawson, D.K.; Ralph, C. John; Scott, J. Michael

1981-01-01

Work in rugged terrain poses some unique problems that should be considered before research is initiated. Besides the obvious physical difficulties of crossing uneven terrain, topography can influence the bird species? composition of a forest and the observer's ability to detect birds and estimate distances. Census results can also be affected by the slower rate of travel on rugged terrain. Density figures may be higher than results obtained from censuses in similar habitat on level terrain because of the greater likelihood of double-recording of individuals and of recording species that sing infrequently. In selecting a census technique, the researcher should weigh the efficiency and applicability of a technique for the objectives of his study in light of the added difficulties posed by rugged terrain. The variable circular-plot method is probably the most effective technique for estimating bird numbers. Bird counts and distance estimates are facilitated because the observer is stationary, and calculations of species? densities take into account differences in effective area covered amongst stations due to variability in terrain or vegetation structure. Institution of precautions that minimize the risk of injury to field personnel can often enhance the observer?s ability to detect birds.

An improved magnetic tape recorder

NASA Technical Reports Server (NTRS)

Uber, P. W.

1968-01-01

Magnetic tape recorder employs a single capstan for simultaneously driving the supply and take-up reels in such a manner that the tape passing between the reels is kept under a predetermined constant tension. This recorder operates with little power and is sufficiently rugged to withstand the severe stresses encountered in high-altitude balloon flight tests.

Fire control planning in the Northern Rocky Mountain region

Treesearch

L. G. Hornby

1936-01-01

In the northern Rocky Mountain region a high degree of protection from fire is necessary to perpetuate forest yields and communities industrially dependent upon them. On rugged and inaccessible areas a green, healthy forest cover is needed for recreation, erosion control, and regulation of water resources. Immense conflagrations continue to challenge the forester. In...

Going the Extra Mile: Supporting Distance Education at University of Alaska Fairbanks

ERIC Educational Resources Information Center

Hahn, Suzan; Lehman, Lisa; Dupras, Rheba

2007-01-01

The Elmer E. Rasmuson Library at the University of Alaska Fairbanks has a long history of supporting distance education through state-of-the-art, remote access services. Harsh climate conditions (heavy snowfall and icing, high winds, and extreme temperatures), rugged terrain, limited road and telephone systems, and permafrost that prevents the…

Active-matrix OLED using 150°C a-Si TFT backplane built on flexible plastic substrate

NASA Astrophysics Data System (ADS)

Sarma, Kalluri R.; Chanley, Charles; Dodd, Sonia R.; Roush, Jared; Schmidt, John; Srdanov, Gordana; Stevenson, Matthew; Wessel, Ralf; Innocenzo, Jeffrey; Yu, Gang; O'Regan, Marie B.; MacDonald, W. A.; Eveson, R.; Long, Ke; Gleskova, Helena; Wagner, Sigurd; Sturm, James C.

2003-09-01

Flexible displays fabricated using plastic substrates have a potential for being very thin, light weight, highly rugged with greatly minimized propensity for breakage, roll-to-roll manufacturing and lower cost. The emerging OLED display media offers the advantage of being a solid state and rugged structure for flexible displays in addition to the many potential advantages of an AM OLED over the currently dominant AM LCD. The current high level of interest in flexible displays is facilitating the development of the required enabling technologies which include development of plastic substrates, low temperature active matrix device and backplane fabrication, and display packaging. In the following we will first discuss our development efforts in the PEN based plastic substrates, active matrix backplane technology, low temperature (150°C) a-Si TFT devices and an AM OLED test chip used for evaluating various candidate designs. We will then describe the design, fabrication and successful evaluation and demonstration of a 64x64 pixel AM OLED test display using a-Si TFT backplane fabricated at 150°C on the flexible plastic substrate.

A rugged 650 V SOI-based high-voltage half-bridge IGBT gate driver IC for motor drive applications

NASA Astrophysics Data System (ADS)

Hua, Qing; Li, Zehong; Zhang, Bo; Chen, Weizhong; Huang, Xiangjun; Feng, Yuxiang

2015-05-01

This paper proposes a rugged high-voltage N-channel insulated gate bipolar transistor (IGBT) gate driver integrated circuit. The device integrates a high-side and a low-side output stages on a single chip, which is designed specifically for motor drive applications. High-voltage level shift technology enables the high-side stage of this device to operate up to 650 V. The logic inputs are complementary metal oxide semiconductor (CMOS)/transistor transistor logic compatible down to 3.3 V. Undervoltage protection functionality with hysteresis characteristic has also been integrated to enhance the device reliability. The device is fabricated in a 1.0 μm, 650 V high-voltage bipolar CMOS double-diffused metal oxide semiconductor (BCD) on silicon-on-insulator (SOI) process. Deep trench dielectric isolation technology is employed to provide complete electrical isolation with advantages such as reduced parasitic effects, excellent noise immunity and low leakage current. Experimental results show that the isolation voltage of this device can be up to approximately 779 V at 25°C, and the leakage current is only 5 nA at 650 V, which is 15% higher and 67% lower than the conventional ones. In addition, it delivers an excellent thermal stability and needs very low quiescent current and offers a high gate driver capability which is needed to adequately drive IGBTs that have large input capacitances.

Simultaneous determination of residues in pollen and high-fructose corn syrup from eight neonicotinoid insecticides by liquid chromatography-tandem mass spectrometry.

PubMed

Chen, Mei; Collins, Erin M; Tao, Lin; Lu, Chensheng

2013-11-01

The neonicotinoids have recently been identified as a potential contributing factor to the sudden decline in adult honeybee population, commonly known as colony collapse disorder (CCD). To protect the health of honeybees and other pollinators, a new, simple, and sensitive liquid chromatography-electrospray ionization mass spectrometry method was developed and validated for simultaneous determination of eight neonicotinoids, including acetamiprid, clothianidin, dinotefuran, flonicamid, imidacloprid, nitenpyram, thiacloprid, and thiamethoxam, in pollen and high-fructose corn syrup (HFCS). In this method, eight neonicotinoids, along with their isotope-labeled internal standards, were extracted from 2 g of pollen or 5 g of HFCS using an optimized quick, easy, cheap, effective, rugged, and safe extraction procedure. The method limits of detection in pollen and HFCS matrices were 0.03 ng/g for acetamiprid, clothianidin, dinotefuran, imidacloprid, thiacloprid, and thiamethoxam and ranged between 0.03 and 0.1 ng/g for nitenpyram and flonicamid. The precision and accuracy were well within the acceptable 20% range. Selectivity, linearity, lower limit of quantitation, matrix effect, recovery, and stability in autosampler were also evaluated during validation. This validated method has been used successfully in analyzing a set of pollen and HFCS samples collected for evaluating potential honeybee exposure to neonicotinoids.

Determination of diflubenzuron and chlorbenzuron in fruits by combining acetonitrile-based extraction with dispersive liquid-liquid microextraction followed by high-performance liquid chromatography.

PubMed

Ruan, Chunqiang; Zhao, Xiang; Liu, Chenglan

2015-09-01

In this study, a simple and low-organic-solvent-consuming method combining an acetonitrile-partitioning extraction procedure followed by "quick, easy, cheap, effective, rugged and safe" cleanup with ionic-liquid-based dispersive liquid-liquid microextraction and high-performance liquid chromatography with diode array detection was developed for the determination of diflubenzuron and chlorbenzuron in grapes and pears. Ionic-liquid-based dispersive liquid-liquid microextraction was performed using the ionic liquid 1-hexyl-3-methylimidazolium hexafluorophosphate as the extractive solvent and acetonitrile extract as the dispersive solvent. The main factors influencing the efficiency of the dispersive liquid-liquid microextraction were evaluated, including the extractive solvent type and volume and the dispersive solvent volume. The validation parameters indicated the suitability of the method for routine analyses of benzoylurea insecticides in a large number of samples. The relative recoveries at three spiked levels ranged between 98.6 and 109.3% with relative standard deviations of less than 5.2%. The limit of detection was 0.005 mg/kg for the two insecticides. The proposed method was successfully used for the rapid determination of diflubenzuron and chlorbenzuron residues in real fruit samples. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Comb-referenced ultra-high sensitivity spectroscopic molecular detection by compact non-linear sources

NASA Astrophysics Data System (ADS)

Cancio, P.; Gagliardi, G.; Galli, I.; Giusfredi, G.; Maddaloni, P.; Malara, P.; Mazzotti, D.; De Natale, P.

2017-11-01

We present a new generation of compact and rugged mid-infrared (MIR) difference-frequency coherent radiation sources referenced to fiber-based optical frequency comb synthesizers (OFCSs). By coupling the MIR radiation to high-finesse optical cavities, high-resolution and high-sensitivity spectroscopy is demonstrated for CH4 and CO2 around 3.3 and 4.5 μm respectively. Finally, the most effective detection schemes for space-craft trace-gas monitoring applications are singled out.

Manx: Close air support aircraft preliminary design

NASA Technical Reports Server (NTRS)

Amy, Annie; Crone, David; Hendrickson, Heidi; Willis, Randy; Silva, Vince

1991-01-01

The Manx is a twin engine, twin tailed, single seat close air support design proposal for the 1991 Team Student Design Competition. It blends advanced technologies into a lightweight, high performance design with the following features: High sensitivity (rugged, easily maintained, with night/adverse weather capability); Highly maneuverable (negative static margin, forward swept wing, canard, and advanced avionics result in enhanced aircraft agility); and Highly versatile (design flexibility allows the Manx to contribute to a truly integrated ground team capable of rapid deployment from forward sites).

Dynamics of an experimental two bladed horizontal axis wind turbine with blade cyclic pitch variation

NASA Technical Reports Server (NTRS)

Hotenemser, K. H.; Swift, A. H. P.

1981-01-01

The turbine under study incorporates the combination of two features: the application of blade cyclic pitch variation; and the use of yaw angle control for rotor speed and torque regulation. Due to its emasculation by passive cyclic pitch variation the rotor can be rapidly yawed without encountering gyroscopic and aerodynamic hub moments and without noticeable out of plane excursions. The two bladed upwind rotor is vane stabilized and of very simple and rugged design. The principle was first checked out with a small scale wind tunnel model and then tested in the atmosphere with a 7.6 meter diameter experimental fully instrumented wind turbine driving a 3 phase alternator. The test results are summarized with respect to structural dynamics and yaw dynamics.

Hydrocarbon sensors and materials therefor

DOEpatents

Pham, Ai Quoc; Glass, Robert S.

2000-01-01

An electrochemical hydrocarbon sensor and materials for use in sensors. A suitable proton conducting electrolyte and catalytic materials have been found for specific application in the detection and measurement of non-methane hydrocarbons. The sensor comprises a proton conducting electrolyte sandwiched between two electrodes. At least one of the electrodes is covered with a hydrocarbon decomposition catalyst. Two different modes of operation for the hydrocarbon sensors can be used: equilibrium versus non-equilibrium measurements and differential catalytic. The sensor has particular application for on-board monitoring of automobile exhaust gases to evaluate the performance of catalytic converters. In addition, the sensor can be utilized in monitoring any process where hydrocarbons are exhausted, for instance, industrial power plants. The sensor is low cost, rugged, sensitive, simple to fabricate, miniature, and does not suffer cross sensitivities.

Water-level and wave measurements in the Chandeleur Islands, Louisiana, 2012 and 2013

USGS Publications Warehouse

Dickhudt, Patrick J.; Sherwood, Christopher R.; DeWitt, Nancy T.

2015-01-01

This report documents measurements of atmospheric pressure, water levels, and waves made by the U.S. Geological Survey in the Chandeleur Islands, Louisiana, during 2012 and 2013 as part of the Barrier Island Evolution Research project. Simple, inexpensive pressure sensors mounted in shallow wells were buried in the beach and left for one hurricane season and one winter-storm season. Gauges with rapid-sampling pressure sensors that provided nondirectional wave data and water-level data were mounted on rugged mounts on the Chandeleur Sound side and at the base of a tower at the northern end of the island chain. Additionally, an atmospheric pressure sensor was mounted on the tower to provide a local atmospheric pressure measurement for correcting the submerged pressure records.

Sculpting bespoke mountains: Determining free energies with basis expansions

NASA Astrophysics Data System (ADS)

Whitmer, Jonathan K.; Fluitt, Aaron M.; Antony, Lucas; Qin, Jian; McGovern, Michael; de Pablo, Juan J.

2015-07-01

The intriguing behavior of a wide variety of physical systems, ranging from amorphous solids or glasses to proteins, is a direct manifestation of underlying free energy landscapes riddled with local minima separated by large barriers. Exploring such landscapes has arguably become one of statistical physics's great challenges. A new method is proposed here for uniform sampling of rugged free energy surfaces. The method, which relies on special Green's functions to approximate the Dirac delta function, improves significantly on existing simulation techniques by providing a boundary-agnostic approach that is capable of mapping complex features in multidimensional free energy surfaces. The usefulness of the proposed approach is established in the context of a simple model glass former and model proteins, demonstrating improved convergence and accuracy over existing methods.

Rotational viscometer for high-pressure, high-temperature fluids

DOEpatents

Carr, K.R.

1983-06-06

The invention is a novel rotational viscometer which is well adapted for use with fluids at high temperatures and/or pressures. In one embodiment, the viscometer include a substantially non-magnetic tube having a closed end and having an open end in communication with a fluid whose viscosity is to be determined. An annular drive magnet is mounted for rotation about the tube. The tube encompasses and supports a rotatable shaft assembly which carries a rotor, or bob, for insertion in the fluid. Affixed to the shaft are (a) a second magnet which is magnetically coupled to the drive magnet and (b) a third magnet. In a typical operation, the drive magnet is rotated to turn the shaft assembly while the shaft rotor is immersed in the fluid. The viscous drag on the rotor causes the shaft assembly to lag the rotation of the drive magnet by an amount which is a function of the amount of viscous drag. A first magnetic pickup generates a waveform whose phase is a function of the angular position of the drive magnet. A second magnetic pickup generates a waveform whose phase is a function of the angular position of the third magnet. Means are provided to generate an output indicative of the phase difference between the two waveforms. The viscometer is comparatively simple, inexpensive, rugged, and does not require shaft seals.

The behavior of Metropolis-coupled Markov chains when sampling rugged phylogenetic distributions.

PubMed

Brown, Jeremy M; Thomson, Robert C

2018-02-15

Bayesian phylogenetic inference involves sampling from posterior distributions of trees, which sometimes exhibit local optima, or peaks, separated by regions of low posterior density. Markov chain Monte Carlo (MCMC) algorithms are the most widely used numerical method for generating samples from these posterior distributions, but they are susceptible to entrapment on individual optima in rugged distributions when they are unable to easily cross through or jump across regions of low posterior density. Ruggedness of posterior distributions can result from a variety of factors, including unmodeled variation in evolutionary processes and unrecognized variation in the true topology across sites or genes. Ruggedness can also become exaggerated when constraints are placed on topologies that require the presence or absence of particular bipartitions (often referred to as positive or negative constraints, respectively). These types of constraints are frequently employed when conducting tests of topological hypotheses (Bergsten et al. 2013; Brown and Thomson 2017). Negative constraints can lead to particularly rugged distributions when the data strongly support a forbidden clade, because monophyly of the clade can be disrupted by inserting outgroup taxa in many different ways. However, topological moves between the alternative disruptions are very difficult, because they require swaps between the inserted outgroup taxa while the data constrain taxa from the forbidden clade to remain close together on the tree. While this precise form of ruggedness is particular to negative constraints, trees with high posterior density can be separated by similarly complicated topological rearrangements, even in the absence of constraints.

The Landscape Documentary: Unveiling the Face of "Wasteland."

ERIC Educational Resources Information Center

Denton, Craig L.

This paper outlines the process of a photographic landscape documentary project which set out to unveil the face of Utah's West Desert (a 42,000 square-mile, sparsely-populated, broad, rugged land of salt bed "playas" and high mountain ranges) comprising one-third of the state and which hoped to make the West Desert, recently under…

A Modern Bréguet-Type Galvanometer

ERIC Educational Resources Information Center

Daffron, John A.; Greenslade, Thomas B., Jr.

2015-01-01

Recently the handsome little galvanometer (only 10 cm high) in Fig. 1 came into the Greenslade Collection. This is a design without a moving coil and, consequently, is very rugged. At the same time, John Daffron independently sent Tom Greenslade the picture of a similar galvanometer that he had made some years back and has been using for…

Double Arm Linkage precision Linear motion (DALL) Carriage, a simplified, rugged, high performance linear motion stage for the moving mirror of an Fourier Transform Spectrometer or other system requiring precision linear motion

NASA Astrophysics Data System (ADS)

Johnson, Kendall B.; Hopkins, Greg

2017-08-01

The Double Arm Linkage precision Linear motion (DALL) carriage has been developed as a simplified, rugged, high performance linear motion stage. Initially conceived as a moving mirror stage for the moving mirror of a Fourier Transform Spectrometer (FTS), it is applicable to any system requiring high performance linear motion. It is based on rigid double arm linkages connecting a base to a moving carriage through flexures. It is a monolithic design. The system is fabricated from one piece of material including the flexural elements, using high precision machining. The monolithic design has many advantages. There are no joints to slip or creep and there are no CTE (coefficient of thermal expansion) issues. This provides a stable, robust design, both mechanically and thermally and is expected to provide a wide operating temperature range, including cryogenic temperatures, and high tolerance to vibration and shock. Furthermore, it provides simplicity and ease of implementation, as there is no assembly or alignment of the mechanism. It comes out of the machining operation aligned and there are no adjustments. A prototype has been fabricated and tested, showing superb shear performance and very promising tilt performance. This makes it applicable to both corner cube and flat mirror FTS systems respectively.

Development of a high-speed wavelength-agile CO2 local oscillator for heterodyne DIAL measurements

NASA Astrophysics Data System (ADS)

Senft, Daniel C.; Pierrottet, Diego F.

2002-06-01

A high repetition rate, wavelength agile CO2 laser has been developed at the Air Force Research Laboratory for use as a local oscillator in a heterodyne detection receiver. Fats wavelength selection is required for measurements of airborne chemical vapors using the differential absorption lidar (DIAL) technique. Acousto-optic modulator are used to tune between different wavelengths at high speeds without the need for moving mechanical parts. Other advantages obtained by the use of acousto-optic modulators are laser output power control per wavelength and rugged packaging for field applications. The local oscillator design is described, and the results from laboratory DIAL measurements are presented. The coherent remote optical sensor system is an internal research project being conducted by the Air Force Research Laboratory Directed Energy Directorate, Active Remote Sensing Branch. The objective of the project is to develop a new long-range standoff spectral sensor that takes advantage of the enhanced performance capabilities coherent detection can provide. Emphasis of the development is on a low cost, compact, and rugged active sensor exclusively designed for heterodyne detection using the differential absorption lidar technique. State of the art technologies in waveguide laser construction and acousto- optics make feasible the next generation of lasers capable of supporting coherent lidar system requirements. Issues addressed as part of the development include optoelectronic engineering of a low cost rugged system, and fast data throughput for real time chemical concentration measurements. All hardware used in this sensor are off-the- shelf items, so only minor hardware modifications were required for the system as it stands. This paper describes a high-speed heterodyne detection CO2 DIAL system that employs a wavelength agile, acousto-optically tuned local oscillator in the receiver. Sample experimental data collected in a controlled environment are presented as well. Chemical detection using 12 wavelengths at 200 pulses per second has been demonstrated. Initial progress on experiments to make a direct, simultaneous comparison of heterodyne and direct detection DIAL systems will also be described.

A natural-language interface to a mobile robot

NASA Technical Reports Server (NTRS)

Michalowski, S.; Crangle, C.; Liang, L.

1987-01-01

The present work on robot instructability is based on an ongoing effort to apply modern manipulation technology to serve the needs of the handicapped. The Stanford/VA Robotic Aid is a mobile manipulation system that is being developed to assist severely disabled persons (quadriplegics) in performing simple activities of everyday living in a homelike, unstructured environment. It consists of two major components: a nine degree-of-freedom manipulator and a stationary control console. In the work presented here, only the motions of the Robotic Aid's omnidirectional motion base have been considered, i.e., the six degrees of freedom of the arm and gripper have been ignored. The goal has been to develop some basic software tools for commanding the robot's motions in an enclosed room containing a few objects such as tables, chairs, and rugs. In the present work, the environmental model takes the form of a two-dimensional map with objects represented by polygons. Admittedly, such a highly simplified scheme bears little resemblance to the elaborate cognitive models of reality that are used in normal human discourse. In particular, the polygonal model is given a priori and does not contain any perceptual elements: there is no polygon sensor on board the mobile robot.

Adaptation in Tunably Rugged Fitness Landscapes: The Rough Mount Fuji Model

PubMed Central

Neidhart, Johannes; Szendro, Ivan G.; Krug, Joachim

2014-01-01

Much of the current theory of adaptation is based on Gillespie’s mutational landscape model (MLM), which assumes that the fitness values of genotypes linked by single mutational steps are independent random variables. On the other hand, a growing body of empirical evidence shows that real fitness landscapes, while possessing a considerable amount of ruggedness, are smoother than predicted by the MLM. In the present article we propose and analyze a simple fitness landscape model with tunable ruggedness based on the rough Mount Fuji (RMF) model originally introduced by Aita et al. in the context of protein evolution. We provide a comprehensive collection of results pertaining to the topographical structure of RMF landscapes, including explicit formulas for the expected number of local fitness maxima, the location of the global peak, and the fitness correlation function. The statistics of single and multiple adaptive steps on the RMF landscape are explored mainly through simulations, and the results are compared to the known behavior in the MLM model. Finally, we show that the RMF model can explain the large number of second-step mutations observed on a highly fit first-step background in a recent evolution experiment with a microvirid bacteriophage. PMID:25123507

Local flow measurements at the inlet spike tip of a Mach 3 supersonic cruise airplane

NASA Technical Reports Server (NTRS)

Johnson, H. J.; Montoya, E. J.

1973-01-01

The flow field at the left inlet spike tip of a YF-12A airplane was examined using at 26 deg included angle conical flow sensor to obtain measurements at free-stream Mach numbers from 1.6 to 3.0. Local flow angularity, Mach number, impact pressure, and mass flow were determined and compared with free-stream values. Local flow changes occurred at the same time as free-stream changes. The local flow usually approached the spike centerline from the upper outboard side because of spike cant and toe-in. Free-stream Mach number influenced the local flow angularity; as Mach number increased above 2.2, local angle of attack increased and local sideslip angle decreased. Local Mach number was generally 3 percent less than free-stream Mach number. Impact-pressure ratio and mass flow ratio increased as free-stream Mach number increased above 2.2, indicating a beneficial forebody compression effect. No degradation of the spike tip instrumentation was observed after more than 40 flights in the high-speed thermal environment encountered by the airplane. The sensor is rugged, simple, and sensitive to small flow changes. It can provide accurate imputs necessary to control an inlet.

Radhard optical patchcords and packaging for satellites using liquid crystal polymers

NASA Astrophysics Data System (ADS)

O'Riorden, S.; Mahapatra, A.

2017-11-01

There are many advantages to employing fiber optics for high capacity satellite communication. However, optical cables can be susceptible to high radiation, temperature extremes and vacuum environment. Any hardware used in these systems must be rugged, durable and immune to the detrimental effects of the aforementioned conditions. Standard COTS optical fiber will darken when exposed to high levels of radiation limiting the effectiveness of the communications system. Of particular concern to satellites in GEO are energetic electrons, bursts of heavy particles due to solar storms which can cause total dose and single event effects (SEE). Conventional fiber optic cables have several issues performing in high radiation environments. Linden has patented and developed a novel cable using an extruded layer of Liquid Crystal Polymer (LCP) applied to commercially available fiber. Total dose effects are minimized by shielding with Liquid Crystal Polymer jacketing. It is a simple, inexpensive way to increase the radiation shielding and mechanical performance of cables in satellites while concomitantly providing hermeticity and thus increased fatigue factor for optical glass. • LCPs exposed to 5000 Mrad dose of gamma rays retain in excess of 90% of their mechanical properties. • LCPs exposed to 1 Mrad radiation dose with energetic protons retain almost 100% of their mechanical strength. Tensile modulus increases with exposure to the radiation. • Weight for weight the proton absorbing power of LCP is 25% better than that of aluminum. We will present experimental data on radhard optical patchcords.

Development, Manufacturing, and Preparation for Serial Production of Low Noise Seismometers Final Report CRADA No. TC02096.0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vergino, E. S.; Passmore, P. R.

2012-01-23

This was a collaborative effort between Lawrence Livermore National Security, LLC as manager and operator of Lawrence Livermore National Laboratory (LLNL) and Refraction Technology, Inc. (REF TEK), to collaborate on the development of a broadband, competitive low-noise seismometer, rugged and easy to use for field deployments. The work involved collaborative work between LLNL, REF TEK and a group led by Federal State Unitary Enterprise, Research Institute of Pulse Technique (RIPT), Moscow, Russia. The proposed work focused on bringing an improved version of the Russian SDSE seismometer from development phase to production in two versions. The first was a very lowmore » cost, rugged, broadband seismometer for field deployment that would achieve noise levels comparable to the standard earth low noise model (LNM) of the USGS. All three components were integrated into one case, and have sensitivity near 2000 v/m/s, and analog output with bandwidth of .01 to 40 Hz with high coherence.« less

Lithographically defined microporous carbon structures

DOEpatents

Burckel, David Bruce; Washburn, Cody M.; Polsky, Ronen; Brozik, Susan M.; Wheeler, David R.

2013-01-08

A lithographic method is used to fabricate porous carbon structures that can provide electrochemical electrodes having high surface area with uniform and controllable dimensions, providing enormous flexibility to tailor the electrodes toward specific applications. Metal nanoparticles deposited on the surface of the porous carbon electrodes exhibit ultra small dimensions with uniform size distribution. The resulting electrodes are rugged, electrically conductive and show excellent electrochemical behavior.

Late winter and early spring home range and habitat use of the endangered Carolina northern flying squirrel in western North Carolina

Treesearch

W. Mark Ford; Christine A. Kelly; Jane L. Rodrigue; Richard H. Odom; Douglas Newcomb; L. Michelle Gilley; Corrine A. Diggins

2014-01-01

The Carolina northern flying squirrel Glaucomys sabrinus coloratus is an endangered subspecies that is restricted to high elevation forests in the southern Appalachian Mountains. Owing to rugged terrain and nocturnal habits, the subspecies' natural history, home range characteristics and habitat preferences are poorly known. We radio-tracked 3...

Adhesion testing device

NASA Technical Reports Server (NTRS)

LaPeyronnie, Glenn M. (Inventor); Huff, Charles M. (Inventor)

2010-01-01

The present invention provides a testing apparatus and method for testing the adhesion of a coating to a surface. The invention also includes an improved testing button or dolly for use with the testing apparatus and a self aligning button hook or dolly interface on the testing apparatus. According to preferred forms, the apparatus and method of the present invention are simple, portable, battery operated rugged, and inexpensive to manufacture and use, are readily adaptable to a wide variety of uses, and provide effective and accurate testing results. The device includes a linear actuator driven by an electric motor coupled to the actuator through a gearbox and a rotatable shaft. The electronics for the device are contained in the head section of the device. At the contact end of the device, is positioned a self aligning button hook, attached below the load cell located on the actuator shaft.

Engine spectrometer probe and method of use

NASA Technical Reports Server (NTRS)

Barkhoudarian, Sarkis (Inventor); Kittinger, Scott A. (Inventor)

2006-01-01

The engine spectrometer probe and method of using the same of the present invention provides a simple engine spectrometer probe which is both lightweight and rugged, allowing an exhaust plume monitoring system to be attached to a vehicle, such as the space shuttle. The engine spectrometer probe can be mounted to limit exposure to the heat and debris of the exhaust plume. The spectrometer probe 50 comprises a housing 52 having an aperture 55 and a fiber optic cable 60 having a fiber optic tip 65. The fiber optic tip 65 has an acceptance angle 87 and is coupled to the aperture 55 so that the acceptance angle 87 intersects the exhaust plume 30. The spectrometer probe can generate a spectrum signal from light in the acceptance angle 506 and the spectrum signal can be provided to a spectrometer 508.

High-throughput method based on quick, easy, cheap, effective, rugged and safe followed by liquid chromatography-multi-wavelength detection for the quantification of multiclass polyphenols in wines.

PubMed

Fontana, Ariel R; Bottini, Rubén

2014-05-16

In this work, a reliable, simple, fast, inexpensive and robust sample preparation approach for the determination of multiclass polyphenols in wine samples is proposed. The polyphenols selected for this work were gallic acid, (+)-catechin, (-)-epicatechin, caffeic acid, syringic acid, coumaric acid, ferulic acid, trans-resveratrol, quercetin and cinnamic acid. The method is based on QuEChERS (quick, easy, cheap, effective, rugged and safe) extraction technique coupled with dispersive solid-phase extraction (d-SPE) clean-up. Under optimized conditions, the analytes were extracted from 5mL wine samples (previously acidified with 1% formic acid) using 2.5mL acetonitrile. For phase separation, 1.5g NaCl and 4g anhydrous MgSO4 were added. Then, a 1mL aliquot of the partitioned supernatant was cleaned-up using d-SPE with a combination of 150mg CaCl2, 50mg primary-secondary amine (PSA) and 50mgC18 as sorbents. A 250μL aliquot of the obtained cleaned extract was concentrated to dryness and taken up with the initial mobile phase previous to liquid chromatography-multi-wavelength detection (LC-MWD). The proposed method provided limits of detection (LODs) ranging from 0.004 to 0.079μgmL(-1) and an inter-day variability below 12% RSD for all analytes in red and white wine samples. Considering external calibration (red wines) and matrix-matched calibration (white wines) as quantification techniques, the overall recoveries (accuracy) of the method ranged between 75.0% and 119.6% for red and white wine samples, respectively. The developed method was applied for the determination of polyphenols in 10 wines produced in Argentina. Nine phenolic compounds were determined, at concentrations above detectable levels in the method. The maximum concentrations corresponded to (-)-epicatechin in white wines, while gallic acid and (+)-catechin were the most abundant in red wines. Copyright © 2014 Elsevier B.V. All rights reserved.

Time-dependent effects of heat advection and topography on cooling histories during erosion

NASA Astrophysics Data System (ADS)

Mancktelow, Neil S.; Grasemann, Bernhard

1997-03-01

Both erosion and surface topography cause a time-dependent variation in isotherm geometry that can result in significant errors in estimating natural exhumation rates from geochronologic data. Analytical solutions and two-dimensional numerical modelling are used to investigate the magnitude of these inaccuracies for conditions appropriate to many rapidly exhumed mountain chains of rugged relief. It is readily demonstrated that uplift of the topographic surface has a negligible effect on the cooling history of an exhumed rock sample and cannot be quantified by current geochronologic methods. The topography itself perturbs the isotherms to a depth that depends on both the vertical and horizontal scale of the surface relief. Estimations employing different isotopic systems in the same sample with higher closure temperatures (> 200°C) are not generally influenced by topography. However, direct conversion of cooling rates to exhumation rates assuming a simple constant linear geotherm markedly underestimates peak rates, due to variation of the geothermal gradient in time and space and to the time lag between exhumation and cooling. Estimations based on the altitude variation in apatite fission-track ages are less prone to such inaccuracies in geothermal gradient but are affected by near-surface time-dependent variation in isotherm depth due to advection and topography. In tectonically active mountain belts, high exhumation rates are coupled with rugged topography, and exhumation rates may be markedly overestimated, by factors of 2 or more. Even at lower exhumation rates on the order of 1 mm/a, the shape of the cooling curve is modified by advection and topography. A convex-concave shape to the cooling curve does not necessarily imply a change of exhumation rate; it may also be attained by a more complicated geothermal gradient induced by topographic relief. Very fast cooling below 100°C, often interpreted as reflecting faster exhumation, can be more simply explained by the lateral cooling effect of topographic relief, with samples exhumed in valleys displaying a different near-surface cooling history to those on ridge crests.

Instrumentation for Aim Point Determination in the Close-in Battle

DTIC Science & Technology

2007-12-01

Rugged camcorder with remote “ lipstick ” camera (http://www.samsung.com/Products/ Camcorder/DigitalMemory/files/scx210wl.pdf). ........ 5 Figure 5...target. One way of making a measurement is to mount a small “ lipstick ” camera to the rifle with a mount similar to the laser-tag transmitter mount...technology.com/contractors/surveillance/viotac-inc/viotac-inc1.html). Figure 4. Rugged camcorder with remote “ lipstick ” camera (http://www.samsung.com

Southeast Asia, Report No. 1298.

DTIC Science & Technology

1983-06-10

the state to increase the tea area to 800 hectares. That is an outstanding goal with many bold, practi- cal measures which the party organization ... increased its prodcution of the various kinds of export rugs made from such agricultural products. Its output of thin jute rugs increased by 82,000 square...NHAN DAN, 2 Apr 831 6 Ho Chi Minh City 11th Precinct Improves Security, Social Order (Hoang Lan; CHINH NGHIA, 17 Apr 83l 10 Hanoi People’s Organ

Rugged Walking Robot

NASA Technical Reports Server (NTRS)

Larimer, Stanley J.; Lisec, Thomas R.; Spiessbach, Andrew J.

1990-01-01

Proposed walking-beam robot simpler and more rugged than articulated-leg walkers. Requires less data processing, and uses power more efficiently. Includes pair of tripods, one nested in other. Inner tripod holds power supplies, communication equipment, computers, instrumentation, sampling arms, and articulated sensor turrets. Outer tripod holds mast on which antennas for communication with remote control site and video cameras for viewing local and distant terrain mounted. Propels itself by raising, translating, and lowering tripods in alternation. Steers itself by rotating raised tripod on turntable.

Genetic algorithm dynamics on a rugged landscape

NASA Astrophysics Data System (ADS)

Bornholdt, Stefan

1998-04-01

The genetic algorithm is an optimization procedure motivated by biological evolution and is successfully applied to optimization problems in different areas. A statistical mechanics model for its dynamics is proposed based on the parent-child fitness correlation of the genetic operators, making it applicable to general fitness landscapes. It is compared to a recent model based on a maximum entropy ansatz. Finally it is applied to modeling the dynamics of a genetic algorithm on the rugged fitness landscape of the NK model.

High-performance liquid chromatographic assay for the determination of novel triazole antifungal agents in tissue. Application to tissue distribution studies.

PubMed

Khan, J K; Montaseri, H; Poglod, M; Bu, H Z; Daneshtalab, M; Micetich, R G

2000-08-01

A simple and rugged reversed-phase high-performance liquid chromatographic method with ultraviolet absorbance detection at 263 nm was developed and validated for the analysis of novel triazole antifungal agents SYN-2869 and its derivatives in tissues. The method involved homogenization with 0.01 M phosphate buffer (pH 7.8) for lung, brain and spleen tissues. The liver and kidneys were homogenized with acetonitrile:acetone (1:1). The plasma proteins were precipitated with ice-cold acetonitrile and supernatent was evaporated to dryness. The reconstituted samples were injected onto an HPLC system. SYN-2869 was separated from the matrix components on a symmetry C(18) column using a aqueous mobile phase of acetonitrile and water with a flow rate of 1 mL/min. A step gradient of 40-80% acetonitrile eluted SYN-2869 and the internal standard (SYN-2506). The linear range was 0.5-10 microgram/g (r(2) > 0.99). The limit of quantitation was 0.5 microgram/g. The inter-day precision and accuracy for SYN 2869 standard concentration were from 2.6 to 7.4% and from -1.56 to +3.29%, respectively. The method was applied to tissue samples collected from single intravenous administration to mice to evaluate the distribution of these novel antifungal agents to different tissues. Copyright 2000 John Wiley & Sons, Ltd.

Development of Plastic Substrate Technology for Active Matrix Liquid Crystal Displays Final Report CRADA No. TC-761-93

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carey, P.; Kamath, H.

Raychem Corporation (RYC) and the Lawrence Livermore National Laboratory (LLNL) conducted a development program with the goal to make rugged, low-cost., high-resolution flat panel displays based on RYC's proprietary Nematic Curvilinear Aligned Phase (NCAP) liquid crystal and LLNL's patented processes for the formation and doping of polycrystalline silicon on low-temperature, flexible, plastic substrates.

Custom avionics-grade AM LCDs for high performance military and avionics applications

NASA Astrophysics Data System (ADS)

Niemczyk, James

2003-09-01

American Panel Corporation in Alpharetta Georgia and LG-Philips-LCD in Seoul South Korea have a strategic alliance for the design and manufacture of custom AMLCD products targeted for the military vehicle and avionics sector. As part of this relationship, new innovations in AMLCD technology specifically aimed at the rugged and avionics applications have been developed and are now brought to the marketplace

Influence of climate and land use on historical surface fires in pine-oak forests, Sierra Madre Occidental, Mexico

Treesearch

Emily K. Heyerdahl; Ernesto Alvarado

2003-01-01

The rugged mountains of the Sierra Madre Occidental, in north-central Mexico, support a mosaic of diverse ecosystems. Of these, the high-elevation, temperate pine-oak forests are ecologically significant for their extensiveness and biodiversity. They cover nearly half the land area in the states of Durango and Chihuahua (42%), and comprise a similar percentage of the...

Two-dimensional frequency-domain acoustic full-waveform inversion with rugged topography

NASA Astrophysics Data System (ADS)

Zhang, Qian-Jiang; Dai, Shi-Kun; Chen, Long-Wei; Li, Kun; Zhao, Dong-Dong; Huang, Xing-Xing

2015-09-01

We studied finite-element-method-based two-dimensional frequency-domain acoustic FWI under rugged topography conditions. The exponential attenuation boundary condition suitable for rugged topography is proposed to solve the cutoff boundary problem as well as to consider the requirement of using the same subdivision grid in joint multifrequency inversion. The proposed method introduces the attenuation factor, and by adjusting it, acoustic waves are sufficiently attenuated in the attenuation layer to minimize the cutoff boundary effect. Based on the law of exponential attenuation, expressions for computing the attenuation factor and the thickness of attenuation layers are derived for different frequencies. In multifrequency-domain FWI, the conjugate gradient method is used to solve equations in the Gauss-Newton algorithm and thus minimize the computation cost in calculating the Hessian matrix. In addition, the effect of initial model selection and frequency combination on FWI is analyzed. Examples using numerical simulations and FWI calculations are used to verify the efficiency of the proposed method.

Rugged superconducting detector for monitoring infrared energy sources in harsh environments

NASA Astrophysics Data System (ADS)

Laviano, F.; Gerbaldo, R.; Ghigo, G.; Gozzelino, L.; Minetti, B.; Rovelli, A.; Mezzetti, E.

2010-12-01

Broadband electromagnetic characterization of hot plasmas, such as in nuclear fusion reactors and related experiments, requires detecting systems that must withstand high flux of particles and electromagnetic radiations. We propose a rugged layout of a high temperature superconducting detector aimed at 3 THz collective Thomson scattering (CTS) spectroscopy in hot fusion plasma. The YBa2Cu3O7 - x superconducting film is patterned by standard photolithography and the sensing area of the device is created by means of high-energy heavy ion irradiation, in order to modify the crystal structure both of the superconducting film and of the substrate. This method diminishes process costs and resulting device fragility due to membrane or air-bridge structures that are commonly needed for MIR and FIR radiation detection. Moreover the sensing area of the device is wired by the same superconducting material and thus excellent mechanical strength is exhibited by the whole device, due to the oxide substrate. Continuous wave operation of prototype devices is demonstrated at liquid nitrogen temperature, for selected infrared spectra of broadband thermal energy sources. Several solutions, which exploit the advantages coming from the robustness of this layout in terms of intrinsic radiation hardness of the superconducting material and of the needed optical components, are analysed with reference to applications of infrared electromagnetic detectors in a tokamak machine environment.

Estimating explosion properties of normal hydrogen-rich core-collapse supernovae

NASA Astrophysics Data System (ADS)

Pejcha, Ondrej

2017-08-01

Recent parameterized 1D explosion models of hundreds of core-collapse supernova progenitors suggest that success and failure are intertwined in a complex pattern that is not a simple function of the progenitor initial mass. This rugged landscape is present also in other explosion properties, allowing for quantitative tests of the neutrino mechanism from observations of hundreds of supernovae discovered every year. We present a new self-consistent and versatile method that derives photospheric radius and temperature variations of normal hydrogen-rich core-collapse supernovae based on their photometric measurements and expansion velocities. We construct SED and bolometric light curves, determine explosion energies, ejecta and nickel masses while taking into account all uncertainties and covariances of the model. We describe the efforts to compare the inferences to the predictions of the neutrino mechanim. The model can be adapted to include more physical assumptions to utilize primarily photometric data coming from surveys such as LSST.

Experimental rugged fitness landscape in protein sequence space.

PubMed

Hayashi, Yuuki; Aita, Takuyo; Toyota, Hitoshi; Husimi, Yuzuru; Urabe, Itaru; Yomo, Tetsuya

2006-12-20

The fitness landscape in sequence space determines the process of biomolecular evolution. To plot the fitness landscape of protein function, we carried out in vitro molecular evolution beginning with a defective fd phage carrying a random polypeptide of 139 amino acids in place of the g3p minor coat protein D2 domain, which is essential for phage infection. After 20 cycles of random substitution at sites 12-130 of the initial random polypeptide and selection for infectivity, the selected phage showed a 1.7x10(4)-fold increase in infectivity, defined as the number of infected cells per ml of phage suspension. Fitness was defined as the logarithm of infectivity, and we analyzed (1) the dependence of stationary fitness on library size, which increased gradually, and (2) the time course of changes in fitness in transitional phases, based on an original theory regarding the evolutionary dynamics in Kauffman's n-k fitness landscape model. In the landscape model, single mutations at single sites among n sites affect the contribution of k other sites to fitness. Based on the results of these analyses, k was estimated to be 18-24. According to the estimated parameters, the landscape was plotted as a smooth surface up to a relative fitness of 0.4 of the global peak, whereas the landscape had a highly rugged surface with many local peaks above this relative fitness value. Based on the landscapes of these two different surfaces, it appears possible for adaptive walks with only random substitutions to climb with relative ease up to the middle region of the fitness landscape from any primordial or random sequence, whereas an enormous range of sequence diversity is required to climb further up the rugged surface above the middle region.

Experimental Rugged Fitness Landscape in Protein Sequence Space

PubMed Central

Hayashi, Yuuki; Aita, Takuyo; Toyota, Hitoshi; Husimi, Yuzuru; Urabe, Itaru; Yomo, Tetsuya

2006-01-01

The fitness landscape in sequence space determines the process of biomolecular evolution. To plot the fitness landscape of protein function, we carried out in vitro molecular evolution beginning with a defective fd phage carrying a random polypeptide of 139 amino acids in place of the g3p minor coat protein D2 domain, which is essential for phage infection. After 20 cycles of random substitution at sites 12–130 of the initial random polypeptide and selection for infectivity, the selected phage showed a 1.7×104-fold increase in infectivity, defined as the number of infected cells per ml of phage suspension. Fitness was defined as the logarithm of infectivity, and we analyzed (1) the dependence of stationary fitness on library size, which increased gradually, and (2) the time course of changes in fitness in transitional phases, based on an original theory regarding the evolutionary dynamics in Kauffman's n-k fitness landscape model. In the landscape model, single mutations at single sites among n sites affect the contribution of k other sites to fitness. Based on the results of these analyses, k was estimated to be 18–24. According to the estimated parameters, the landscape was plotted as a smooth surface up to a relative fitness of 0.4 of the global peak, whereas the landscape had a highly rugged surface with many local peaks above this relative fitness value. Based on the landscapes of these two different surfaces, it appears possible for adaptive walks with only random substitutions to climb with relative ease up to the middle region of the fitness landscape from any primordial or random sequence, whereas an enormous range of sequence diversity is required to climb further up the rugged surface above the middle region. PMID:17183728

OM300 Direction Drilling Module

DOE Data Explorer

MacGugan, Doug

2013-08-22

OM300 – Geothermal Direction Drilling Navigation Tool: Design and produce a prototype directional drilling navigation tool capable of high temperature operation in geothermal drilling Accuracies of 0.1° Inclination and Tool Face, 0.5° Azimuth Environmental Ruggedness typical of existing oil/gas drilling Multiple Selectable Sensor Ranges High accuracy for navigation, low bandwidth High G-range & bandwidth for Stick-Slip and Chirp detection Selectable serial data communications Reduce cost of drilling in high temperature Geothermal reservoirs Innovative aspects of project Honeywell MEMS* Vibrating Beam Accelerometers (VBA) APS Flux-gate Magnetometers Honeywell Silicon-On-Insulator (SOI) High-temperature electronics Rugged High-temperature capable package and assembly process

RNA Futile Cycling in Model Persisters Derived from MazF Accumulation (Open Access)

DTIC Science & Technology

2015-11-17

they remained highly metabolically active . We further uncovered a futile cycle driven by continued transcription and MazF-mediated transcript degradation...presence of antibiotics (7), although exceptions have been noted for prod- rugs that require activation (8). Rather, they are rare phenotypic variants...arise from slowly grow- ing or nongrowing bacteria with reduced metabolic activity , where antibiotic targets are inactive and resilient to antibiotic

Use of ammonium formate in QuEChERS for high-throughput analysis of pesticides in food by fast, low-pressure gas chromatography and liquid chromatography tandem mass spectrometry

USDA-ARS?s Scientific Manuscript database

The “quick, easy, cheap, effective, rugged, and safe” (QuEChERS) approach to sample preparation is widely applied in pesticide residue analysis, but the use of magnesium sulfate for salting out in the method is not ideal for mass spectrometry. In this study we developed and evaluated three new diffe...

Defense Small Business Innovation Research Program (SBIR). Volume 1. Army Abstracts of Phase 1 Awards 1993

DTIC Science & Technology

1993-01-01

glass phase transformations, will identify characteristic signatures associated with film formation. Phase I technical objectives include the analysis...Fast, Highly Sensitive, Rugged, Miniature Spectroradiometer Based on a TeO2 Acousto-optic Tunable Filter (AOTF) Abstract: Brimrose proposes to research...this problem. The use of poltruded glass fiber reinforcing elements containing recycled plastic in their matrices will also be examined as this will

Guide to U.S. Atmospheric Nuclear Weapon Effects Data

DTIC Science & Technology

1993-12-01

biological warfare agents, and radiation dosimeters . XRD- 163 identifies the test location of each 4-6 biological sample. Reports containing the results...along with position of the animals at the time of the detonation. Vycor Glass Gamma Ray Dosimeters XRD-176 A rugged new dosimeter capable of measuring...gamma doses on animals exposed to high levels of radiation was employed during Able. Dosimeter readings, locations, and animal condition are reported

Quantification of metronidazole in human plasma using a highly sensitive and rugged LC-MS/MS method for a bioequivalence study.

PubMed

Vanol, Pravin G; Sanyal, Mallika; Shah, Priyanka A; Shrivastav, Pranav S

2018-03-23

A highly sensitive, selective and rugged method has been described for the quantification of metronidazole (MTZ) in human plasma by liquid chromatography-tandem mass spectrometry using metronidazole-d4 as the internal standard (IS). The analyte and the IS were extracted from 100 μL plasma by liquid-liquid extraction. The clear samples obtained were chromatographed on an ACE C 18 (100 × 4.6 mm, 5 μm) column using acetonitrile and 10.0 mm ammonium formate in water, pH 4.00 (80:20, v/v) as the mobile phase. A triple quadrupole mass spectrometer system equipped with turbo ion spray source and operated in multiple reaction monitoring mode was used for the detection and quantification of MTZ. The calibration range was established from 0.01 to 10.0 μg/mL. The results of validation testing for precision and accuracy, selectivity, matrix effects, recovery and stability complied with current bioanalytical guidelines. A run time of 3.0 min permitted analysis of more than 300 samples in a day. The method was applied to a bioequivalence study with 250 mg MTZ tablet formulation in 24 healthy Indian males. Copyright © 2018 John Wiley & Sons, Ltd.

Monolithic liquid crystal waveguide Fourier transform spectrometer for gas species sensing

NASA Astrophysics Data System (ADS)

Chao, Tien-Hsin; Lu, Thomas T.; Davis, Scott R.; Rommel, Scott D.; Farca, George; Luey, Ben; Martin, Alan; Anderson, Michael H.

2011-04-01

Jet Propulsion Lab and Vescent Photonics Inc. and are jointly developing an innovative ultracompact (volume < 10 cm3), ultra-low power (<10-3 Watt-hours per measurement and zero power consumption when not measuring), completely non-mechanical Liquid Crystal Waveguide Fourier Transform Spectrometer (LCWFTS) that will be suitable for a variety of remote-platform, in-situ measurements. These devices are made possible by novel electro-evanescent waveguide architecture, enabling "monolithic chip-scale" Electro Optic-FTS (EO-FTS) sensors. The potential performance of these EO-FTS sensors include: i) a spectral range throughout 0.4-5 μm (25000 - 2000 cm-1), ii) high-resolution (Δλ <= 0.1 nm), iii) high-speed (< 1 ms) measurements, and iv) rugged integrated optical construction. This performance potential enables the detection and quantification of a large number of different atmospheric gases simultaneously in the same air mass and the rugged construction will enable deployment on previously inaccessible platforms. The sensor construction is also amenable for analyzing aqueous samples on remote floating or submerged platforms. We will report a proof-of-principle prototype LCWFTS sensor that has been demonstrated in the near-IR (range of 1450-1700 nm) with a 5 nm resolution. This performance is in good agreement with theoretical models, which are being used to design and build the next generation LCWFTS devices.

A hacker's guide to catching a debris flow: Lessons learned from four years of chasing mud in Colorado and southern California

NASA Astrophysics Data System (ADS)

Kean, J. W.; McCoy, S. W.; Staley, D. M.; Coe, J.; Leeper, R.; Tucker, G. E.

2012-12-01

Direct measurements of natural debris flows provide valuable insights into debris-flow processes and hazards. Yet debris flows are difficult to "catch" because they live in rugged terrain, appear infrequently, and have an appetite for destroying monitoring equipment. We present an overview of some successful (and failed) techniques we have used over the past four years to obtain direct measurements of 40+ debris flows in Colorado and southern California. Following the "MacGyver" theme of the session, we focus on the improvised equipment and methods we use in our hunt for quality data. These include an inexpensive erosion sensor to measure rates of debris-flow entrainment, a custom load cell enclosure for measuring debris-flow normal force, tracer rocks implanted with passive integrated transponders, basic pressure transducers to measure debris-flow timing, and standard digital cameras adapted to obtain high-resolution (1936 x 1288 pixels) video footage of debris flows. These techniques are also suitable for catching data on elusive flash floods. In addition, we also share some practical solutions to the logistical problems associated with installing monitoring equipment in rugged debris-flow terrain, such as suspension of non-contact stage gages high above channels.

Modeling of SAW Delay Lines

NASA Technical Reports Server (NTRS)

Wilson, William C.; Atkinson, Gary M.

2007-01-01

Integrated Vehicle Health Monitoring (IVHM) of aerospace vehicles requires rugged sensors having reduced volume, mass, and power that can be used to measure a variety of phenomena. Wireless systems are preferred when retro-fitting sensors onto existing vehicles. Surface Acoustic Wave (SAW) devices are capable of sensing: temperature, pressure, strain, chemical species, mass loading, acceleration, and shear stress. SAW technology is low cost, rugged, lightweight, and extremely low power. To aid in the development of SAW sensors for IVHM applications, a first order model of a SAW Delay line has been created.

Spectral signature of alpine snow cover from the Landsat Thematic Mapper

NASA Technical Reports Server (NTRS)

Dozier, Jeff

1989-01-01

In rugged terrain, snow in the shadows can appear darker than soil or vegetation in the sunlight, making it difficult to interpret satellite data images of rugged terrains. This paper discusses methods for using Thematic Mapper (TM) and SPOT data for automatic analyses of alpine snow cover. Typical spectral signatures of the Landsat TM are analyzed for a range of snow types, atmospheric profiles, and topographic illumination conditions. A number of TM images of Sierra Nevada are analyzed to distinguish several classes of snow from other surface covers.

Advanced X-Ray Sources Ensure Safe Environments

NASA Technical Reports Server (NTRS)

2008-01-01

Ames Research Center awarded inXitu Inc. (formerly Microwave Power Technology), of Mountain View, California, an SBIR contract to develop a new design of electron optics for forming and focusing electron beams that is applicable to a broad class of vacuum electron devices. This technology offers an inherently rugged and more efficient X-ray source for material analysis; a compact and rugged X-ray source for smaller rovers on future Mars missions; and electron beam sources to reduce undesirable emissions from small, widely distributed pollution sources; and remediation of polluted sites.

Quick, easy, cheap, effective, rugged, and safe sample preparation approach for pesticide residue analysis using traditional detectors in chromatography: A review.

PubMed

Rahman, Md Musfiqur; Abd El-Aty, A M; Kim, Sung-Woo; Shin, Sung Chul; Shin, Ho-Chul; Shim, Jae-Han

2017-01-01

In pesticide residue analysis, relatively low-sensitivity traditional detectors, such as UV, diode array, electron-capture, flame photometric, and nitrogen-phosphorus detectors, have been used following classical sample preparation (liquid-liquid extraction and open glass column cleanup); however, the extraction method is laborious, time-consuming, and requires large volumes of toxic organic solvents. A quick, easy, cheap, effective, rugged, and safe method was introduced in 2003 and coupled with selective and sensitive mass detectors to overcome the aforementioned drawbacks. Compared to traditional detectors, mass spectrometers are still far more expensive and not available in most modestly equipped laboratories, owing to maintenance and cost-related issues. Even available, traditional detectors are still being used for analysis of residues in agricultural commodities. It is widely known that the quick, easy, cheap, effective, rugged, and safe method is incompatible with conventional detectors owing to matrix complexity and low sensitivity. Therefore, modifications using column/cartridge-based solid-phase extraction instead of dispersive solid-phase extraction for cleanup have been applied in most cases to compensate and enable the adaptation of the extraction method to conventional detectors. In gas chromatography, the matrix enhancement effect of some analytes has been observed, which lowers the limit of detection and, therefore, enables gas chromatography to be compatible with the quick, easy, cheap, effective, rugged, and safe extraction method. For liquid chromatography with a UV detector, a combination of column/cartridge-based solid-phase extraction and dispersive solid-phase extraction was found to reduce the matrix interference and increase the sensitivity. A suitable double-layer column/cartridge-based solid-phase extraction might be the perfect solution, instead of a time-consuming combination of column/cartridge-based solid-phase extraction and dispersive solid-phase extraction. Therefore, replacing dispersive solid-phase extraction with column/cartridge-based solid-phase extraction in the cleanup step can make the quick, easy, cheap, effective, rugged, and safe extraction method compatible with traditional detectors for more sensitive, effective, and green analysis. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Secondary Emission Calorimeter Sensor Development

NASA Astrophysics Data System (ADS)

Winn, David R.; Onel, Yasar

2012-12-01

In a Secondary Emission electron(SEe) detector module, Secondary Emission electrons (SEe) are generated from an SE surface/cathode, when charged hadronic or electromagnetic particles, particularly shower particles, penetrate an SE sampling module placed between absorber materials (Fe, Cu, Pb, W etc) in calorimeters. The SE cathode is a thin (10-50 nm thick) film (simple metal-oxides, or other higher yield materials) on the surface of a metal plate, which serves as the entrance “window” to a compact vacuum vessel (metal or metal-ceramic); this SE film cathode is analogous to a photocathode, and the SEe are similar to p.e., which are then amplified by dynodes, also is in a PMT. SE sensor modules can make use of electrochemically etched/machined or laser-cut metal mesh dynode sheets, as large as ~30 cm square, to amplify the Secondary Emission Electrons (SEe), much like those that compact metal mesh or mesh dynode PMT's use to amplify p.e.'s. The construction requirements easier than a PMT, since the entire final assembly can be done in air; there are no critical controlled thin film depositions, cesiation or other oxygen-excluded processes or other required vacuum activation, and consequently bake-out can be a refractory temperatures; the module is sealed by normal vacuum techniques (welding or brazing or other high temperature joinings), with a simple final heated vacuum pump-out and tip-off. The modules envisioned are compact, high gain, high speed, exceptionally radiation damage resistant, rugged, and cost effective, and can be fabricated in arbitrary tileable shapes. The SE sensor module anodes can be segmented transversely to sizes appropriate to reconstruct electromagnetic cores with high precision. The GEANT4 and existing calorimeter data estimated calorimeter response performance is between 35-50 Secondary Emission electrons per GeV, in a 1 cm thick Cu absorber calorimeter, with a gain per SEe > 105 per SEe, and an e/pi<1.2. The calorimeter pulse width is estimated to be <15 ns. With fine mesh sampling only (no thick absorbers) the resolution is ~25 MeV at 1 GeV.

Long life electrodes for large-area x-ray generators

NASA Technical Reports Server (NTRS)

Rothe, Dietmar E. (Inventor)

1991-01-01

This invention is directed to rugged, reliable, and long-life electrodes for use in large-area, high-current-density electron gun and x-ray generators which are employed as contamination-free preionizers for high-energy pulsed gas lasers. The electron source at the cathode is a corona plasma formed at the interface between a conductor, or semiconductor, and a high-permittivity dielectric. Detailed descriptions are provided of a reliable cold plasma cathode, as well as an efficient liquid-cooled electron beam target (anode) and x-ray generator which concentrates the x-ray flux in the direction of an x-ray window.

Configurational entropy: an improvement of the quasiharmonic approximation using configurational temperature.

PubMed

Nguyen, Phuong H; Derreumaux, Philippe

2012-01-14

One challenge in computational biophysics and biology is to develop methodologies able to estimate accurately the configurational entropy of macromolecules. Among many methods, the quasiharmonic approximation (QH) is most widely used as it is simple in both theory and implementation. However, it has been shown that this method becomes inaccurate by overestimating entropy for systems with rugged free energy landscapes. Here, we propose a simple method to improve the QH approximation, i.e., to reduce QH entropy. We approximate the potential energy landscape of the system by an effective harmonic potential, and request that this potential must produce exactly the configurational temperature of the system. Due to this constraint, the force constants associated with the effective harmonic potential are increased, or equivalently, entropy of motion governed by this effective harmonic potential is reduced. We also introduce the effective configurational temperature concept which can be used as an indicator to check the anharmonicity of the free energy landscape. To validate the new method we compare it with the recently developed expansion approximate method by calculating entropy of one simple model system and two peptides with 3 and 16 amino acids either in gas phase or in explicit solvent. We show that the new method appears to be a good choice in practice as it is a compromise between accuracy and computational speed. A modification of the expansion approximate method is also introduced and advantages are discussed in some detail.

Design and performance of a rugged standard operative temperature thermometer for avian studies

USGS Publications Warehouse

Bakken, G.S.; Boysen, A.F.; Korschgen, C.E.; Kenow, K.P.; Lima, S.L.

2001-01-01

The lack of a truly satisfactory sensor which can characterize the thermal environment at the spatial scale experienced by small endotherms has hindered study of their thermoregulatory behavior. We describe a general design for a rugged, easily constructed sensor to measure standard operative temperature, Tes. We present specific designs for adult dark-eyed juncos (Junco hyemalis) and hatchling mallards (Anas platyrhynchos). Sensor response was stable and repeatable (??1.4%) over the course of several months. Over the range of conditions for which validation data were available (variable air temperature and wind with negligible net radiation), sensors predicted the mean net heat production of live animals to within ??0.023W (equivalent to ??1??C at Tes= 15??C). The main limit on accuracy was scatter in the data on metabolism and evaporative water loss in live animals. These sensors are far more rugged and easily constructed than the heated taxidermic mounts previously used to measure Tes. These characteristics facilitate the use of significant numbers of sensors in thermal mapping studies of endotherms. ?? 2001 Elsevier Science Ltd. All rights reserved.

Integrated system for single leg walking

NASA Astrophysics Data System (ADS)

Simmons, Reid; Krotkov, Eric; Roston, Gerry

1990-07-01

The Carnegie Mellon University Planetary Rover project is developing a six-legged walking robot capable of autonomously navigating, exploring, and acquiring samples in rugged, unknown environments. This report describes an integrated software system capable of navigating a single leg of the robot over rugged terrain. The leg, based on an early design of the Ambler Planetary Rover, is suspended below a carriage that slides along rails. To walk, the system creates an elevation map of the terrain from laser scanner images, plans an appropriate foothold based on terrain and geometric constraints, weaves the leg through the terrain to position it above the foothold, contacts the terrain with the foot, and applies force enough to advance the carriage along the rails. Walking both forward and backward, the system has traversed hundreds of meters of rugged terrain including obstacles too tall to step over, trenches too deep to step in, closely spaced obstacles, and sand hills. The implemented system consists of a number of task-specific processes (two for planning, two for perception, one for real-time control) and a central control process that directs the flow of communication between processes.

Fabry-Perot interferometer development for rocket engine plume spectroscopy

NASA Astrophysics Data System (ADS)

Bickford, R. L.; Madzsar, G.

1990-07-01

This paper describes a new rugged high-resolution Fabry-Perot interferometer (FPI) designed for rocket engine plume spectroscopy, which is capable of detecting spectral signatures of eroding engine components during rocket engine tests and/or flight operations. The FPI system will make it possible to predict and to respond to the incipient rocket engine failures and to indicate the presence of rocket components degradation. The design diagram of the FPI spectrometer is presented.

Fabry-Perot interferometer development for rocket engine plume spectroscopy

NASA Technical Reports Server (NTRS)

Bickford, R. L.; Madzsar, G.

1990-01-01

This paper describes a new rugged high-resolution Fabry-Perot interferometer (FPI) designed for rocket engine plume spectroscopy, which is capable of detecting spectral signatures of eroding engine components during rocket engine tests and/or flight operations. The FPI system will make it possible to predict and to respond to the incipient rocket engine failures and to indicate the presence of rocket components degradation. The design diagram of the FPI spectrometer is presented.

Rugged Preheaters For Vacuum Plasma Spraying

NASA Technical Reports Server (NTRS)

Woodford, William H.; Mckechnie, Timothy N.; Sander, Lewis D.; Power, Christopher A.; Sander, Heather L.; Nguyen, Dalton D.

1994-01-01

Electric preheater units built to ensure large workpieces to be coated with metals by vacuum plasma spraying heated uniformly to requisite high temperatures by time plasma torch arrives. Units similar to electrical-resistance ribbon heaters in toasters and in some small portable electric "space" heaters. Nichrome resistance-heating ribbons wrapped around ceramic insulating spools on rings and on plates. Round workpiece placed in middle of ring preheater. Plate preheaters stacked as needed near workpiece.

Miniaturized Ion Mobility Spectrometer

NASA Technical Reports Server (NTRS)

Stimac, Robert M. (Inventor); Kaye, William J (Inventor)

2017-01-01

By utilizing the combination of a unique electronic ion injection control circuit in conjunction with a particularly designed drift cell construction, the instantly disclosed ion mobility spectrometer (IMS) achieves increased levels of sensitivity, while achieving significant reductions in size and weight. The instant IMS is of a much simpler and easy to manufacture design, rugged and hermetically sealed, capable of operation at high temperatures to at least 250 degrees Centigrade, and is uniquely sensitive, particularly to explosive chemicals.

Miniaturized Ion Mobility Spectrometer

NASA Technical Reports Server (NTRS)

Kaye, William J. (Inventor); Stimac, Robert M. (Inventor)

2015-01-01

By utilizing the combination of a unique electronic ion injection control circuit in conjunction with a particularly designed drift cell construction, the instantly disclosed ion mobility spectrometer achieves increased levels of sensitivity, while achieving significant reductions in size and weight. The instant IMS is of a much simpler and easy to manufacture design, rugged and hermetically sealed, capable of operation at high temperatures to at least 250.degree. C., and is uniquely sensitive, particularly to explosive chemicals.

Inspection and characterization of flexo-printing plates

NASA Astrophysics Data System (ADS)

Hahlweg, Cornelius; Pescoller, Lukas; Zhao, Wenjing

2013-09-01

In continuation of last year's paper on distorting optics for inspection of 2 1/2D surfaces with convex or elevated elements - like braille paper and other special printing products - the present paper is dedicated to the quality control and characterization of flexo-printing plates. The need for high optical resolution contradicts the need for depth of field. A rugged optical system for gathering a series of microscopic images at various planes of focus is discussed.

Mobile Gait Analysis System for Lower Limb Amputee High-Level Activity Rehabilitation

DTIC Science & Technology

2012-09-01

take this data and give the clinician information they can use immediately to get more insight into existing prosthesis fit or alignment issues, help...Modification of Smart Pylon for prosthesis fit, alignment and gait training purposes – 20 In May the larger, more rugged trans-tibial (TT) Smart Pylon...data to determine metrics to indicate positive patient biomechanics factors and indicate successful prosthesis fit and alignment This will be

High-Performance Power-Semiconductor Packages

NASA Technical Reports Server (NTRS)

Renz, David; Hansen, Irving; Berman, Albert

1989-01-01

A 600-V, 50-A transistor and 1,200-V, 50-A diode in rugged, compact, lightweight packages intended for use in inverter-type power supplies having switching frequencies up to 20 kHz. Packages provide low-inductance connections, low loss, electrical isolation, and long-life hermetic seal. Low inductance achieved by making all electrical connections to each package on same plane. Also reduces high-frequency losses by reducing coupling into inherent shorted turns in packaging material around conductor axes. Stranded internal power conductors aid conduction at high frequencies, where skin effect predominates. Design of packages solves historical problem of separation of electrical interface from thermal interface of high-power semiconductor device.

Evaluation of a Fast and Simple Sample Preparation Method for Polybrominated Diphenyl Ether (PBDE) Flame Retardants and Dichlorodiphenyltrichloroethane (DDT) Pesticides in Fish for Analysis by ELISA Compared with GC-MS/MS.

PubMed

Sapozhnikova, Yelena; Simons, Tawana; Lehotay, Steven J

2015-05-13

A simple, fast, and cost-effective sample preparation method, previously developed and validated for the analysis of organic contaminants in fish using low-pressure gas chromatography-tandem mass spectrometry (LPGC-MS/MS), was evaluated for the analysis of polybrominated diphenyl ethers (PBDEs) and dichlorodiphenyltrichloroethane (DDT) pesticides using enzyme-linked immunosorbent assay (ELISA). The sample preparation technique was based on the quick, easy, cheap, rugged, effective, and safe (QuEChERS) approach with filter-vial dispersive solid phase extraction (d-SPE). Incurred PBDEs and DDTs were analyzed in three types of fish with 3-10% lipid content: Pacific croaker, salmon, and National Institute of Standards and Technology (NIST) Standard Reference Material 1947 (Lake Michigan fish tissue). LPGC-MS/MS and ELISA results were in agreement: 108-111 and 65-82% accuracy ELISA versus LPGC-MS/MS results for PBDEs and DDTs, respectively. Similar detection limits were achieved for ELISA and LPGC-MS/MS. Matrix effects (MEs) were significant (e.g., -60%) for PBDE measurement in ELISA, but not a factor in the case of DDT pesticides. This study demonstrated that the sample preparation method can be adopted for semiquantitative screening analysis of fish samples by commercial kits for PBDEs and DDTs.

Image Intensifier Modules For Use With Commercially Available Solid State Cameras

NASA Astrophysics Data System (ADS)

Murphy, Howard; Tyler, Al; Lake, Donald W.

1989-04-01

A modular approach to design has contributed greatly to the success of the family of machine vision video equipment produced by EG&G Reticon during the past several years. Internal modularity allows high-performance area (matrix) and line scan cameras to be assembled with two or three electronic subassemblies with very low labor costs, and permits camera control and interface circuitry to be realized by assemblages of various modules suiting the needs of specific applications. Product modularity benefits equipment users in several ways. Modular matrix and line scan cameras are available in identical enclosures (Fig. 1), which allows enclosure components to be purchased in volume for economies of scale and allows field replacement or exchange of cameras within a customer-designed system to be easily accomplished. The cameras are optically aligned (boresighted) at final test; modularity permits optical adjustments to be made with the same precise test equipment for all camera varieties. The modular cameras contain two, or sometimes three, hybrid microelectronic packages (Fig. 2). These rugged and reliable "submodules" perform all of the electronic operations internal to the camera except for the job of image acquisition performed by the monolithic image sensor. Heat produced by electrical power dissipation in the electronic modules is conducted through low resistance paths to the camera case by the metal plates, which results in a thermally efficient and environmentally tolerant camera with low manufacturing costs. A modular approach has also been followed in design of the camera control, video processor, and computer interface accessory called the Formatter (Fig. 3). This unit can be attached directly onto either a line scan or matrix modular camera to form a self-contained units, or connected via a cable to retain the advantages inherent to a small, light weight, and rugged image sensing component. Available modules permit the bus-structured Formatter to be configured as required by a specific camera application. Modular line and matrix scan cameras incorporating sensors with fiber optic faceplates (Fig 4) are also available. These units retain the advantages of interchangeability, simple construction, ruggedness, and optical precision offered by the more common lens input units. Fiber optic faceplate cameras are used for a wide variety of applications. A common usage involves mating of the Reticon-supplied camera to a customer-supplied intensifier tube for low light level and/or short exposure time situations.

Dynamic modeling and mobility analysis of the transforming roving-rolling explorer (TRREx) as it Traverses Rugged Martian Terrain

NASA Astrophysics Data System (ADS)

Edwin, Lionel E.; Mazzoleni, Andre P.

2016-03-01

All planetary surface exploration missions thus far have employed traditional rovers with a rocker-bogie suspension. These rovers can navigate moderately rough and flat terrain, but are not designed to traverse rugged terrain with steep slopes. The fact is, however, that the most scientifically interesting missions require exploration platforms with capabilities for navigating such types of rugged terrain. This issue motivates the development of new kinds of rovers that take advantage of the latest advances in robotic technologies to traverse rugged terrain efficiently. This work analyzes one such rover concept called the Transforming Roving-Rolling Explorer (TRREx) that is principally aimed at addressing the above issue. Biologically inspired by the way the armadillo curls up into a ball when threatened, and the way the golden wheel spider uses the dynamic advantages of a sphere to roll down hills when escaping danger, the TRREx rover can traverse like a traditional 6-wheeled rover over conventional terrain, but can also transform itself into a sphere, when necessary, to travel down steep inclines, or navigate rough terrain. This paper investigates the mobility of the TRREx when it is in its rolling mode, i.e. when it is a sphere and can steer itself through actuations that shift its center of mass to achieve the desired direction of roll. A mathematical model describing the dynamics of the rover in this spherical configuration is presented, and actuated rolling is demonstrated through computer simulation. Parametric analyzes that investigate the rover's mobility as a function of its design parameters are also presented. This work highlights the contribution of the spherical rolling mode to the enhanced mobility of the TRREx rover and how it could enable challenging surface exploration missions in the future.

Innovative technology summary report: Houdini{trademark} I and II remotely operated vehicle

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1998-07-01

The US Department of Energy (DOE) is responsible for cleaning up and closing 273 large, aging, underground tanks the department has used for storing approximately 1 million gal of high- and low-level radioactive and mixed waste. The waste`s radioactivity precludes humans from working in the tanks. A remote-controlled retrieval method must be used. The Houdini robot addresses the need for vehicle-based, rugged, remote manipulation systems that can perform waste retrieval, characterization, and inspection tasks. Houdini-I was delivered to ORNL in September 1996, deployed in a cold test facility in November, and first deployed in the gunite tanks in June 1997.more » Since then, it has seen continuous (still on-going) service at ORNL, providing a critical role in the cleanup of two gunite tanks, W-3 and W-4, in the GAAT NTF. Houdini-I has proven rugged, capable of waste retrieval, and able to withstand high reaction force operations such as wall core sampling. It`s even able to operate while hanging, which was the case when Houdini was used to cut and remove cables and steel pipes hanging below manways in Tank W-3. Based upon the lessons learned at ORNL, Houdini`s design has been completely overhauled. A second generation system, Houdini-II, is now being built.« less

Fluid Dynamics of Small, Rugged Vacuum Pumps of Viscous-Drag Type

NASA Technical Reports Server (NTRS)

Russell, John M.

2002-01-01

The need to identify spikes in the concentration of hazardous gases during countdowns to space shuttle launches has led Kennedy Space Center to acquire considerable expertise in the design, construction, and operation of special-purpose gas analyzers of mass-spectrometer type. If such devices could be miniaturized so as to fit in a small airborne package or backpack them their potential applications would include integrated vehicle health monitoring in later-generation space shuttles and in hazardous material detection in airports, to name two examples. The bulkiest components of such devices are vacuum pumps, particularly those that function in the low vacuum range. Now some pumps that operate in the high vacuum range (e.g. molecular-drag and turbomolecular pumps) are already small and rugged. The present work aims to determine whether, on physical grounds, one may or may not adopt the molecular-drag principle to the low-vacuum range (in which case viscous-drag principle is the appropriate term). The deliverable of the present effort is the derivation and justification of some key formulas and calculation methods for the preliminary design of a single-spool, spiral-channel viscous-drag pump.

Highest Resolution Comet Picture Ever Reveals Rugged Terrain - Deep Space 1

NASA Image and Video Library

2001-11-04

In this highest resolution view of the icy, rocky nucleus of comet Borrelly, (about 45 meters or 150 feet per pixel) a variety of terrains and surface textures, mountains and fault structures, and darkened material are visible over the nucleus's surface. This was the final image of the nucleus of comet Borrelly, taken just 160 seconds before Deep Space1's closest approach to it. This image shows the 8-km (5-mile) long nucleus about 3417 kilometers (over 2,000 miles) away. Smooth, rolling plains containing brighter regions are present in the middle of the nucleus and seem to be the source of dust jets seen in the coma. The rugged land found at both ends of the nucleus has many high ridges along the jagged line between day and night on the comet. This rough terrain contains very dark patches that appear to be elevated compared to surrounding areas. In some places the dark material accentuates grooves and apparent faults. Stereo analysis shows the smaller end of the nucleus (lower right) is tipped toward the viewer (out of frame). Sunlight is coming from the bottom of the frame. http://photojournal.jpl.nasa.gov/catalog/PIA03500

A real-time sub-μrad laser beam tracking system

NASA Astrophysics Data System (ADS)

Buske, Ivo; Schragner, Ralph; Riede, Wolfgang

2007-10-01

We present a rugged and reliable real-time laser beam tracking system operating with a high speed, high resolution piezo-electric tip/tilt mirror. Characteristics of the piezo mirror and position sensor are investigated. An industrial programmable automation controller is used to develop a real-time digital PID controller. The controller provides a one million field programmable gate array (FPGA) to realize a high closed-loop frequency of 50 kHz. Beam tracking with a root-mean-squared accuracy better than 0.15 μrad has been laboratory confirmed. The system is intended as an add-on module for established mechanical mrad tracking systems.

Improved Portable Ultrasonic Leak Detectors

NASA Technical Reports Server (NTRS)

Youngquist, Robert C.; Moerk, John S.; Haskell, William D.; Cox, Robert B.; Polk, Jimmy D.; Strobel, James P.; Luaces, Frank

1995-01-01

Improved portable ultrasonic leak detector features three interchangeable ultrasonic-transducer modules, each suited for operation in unique noncontact or contact mode. One module equipped with ultrasound-collecting horn for use in scanning to detect leaks from distance; horn provides directional sensitivity pattern with sensitivity multiplied by factor of about 6 in forward direction. Another module similar, does not include horn; this module used for scanning close to suspected leak, where proximity of leak more than offsets loss of sensitivity occasioned by lack of horn. Third module designed to be pressed against leaking vessel; includes rugged stainless-steel shell. Improved detectors perform significantly better, smaller, more rugged, and greater sensitivity.

2D scanning Rotman lens structure for smart collision avoidance sensors

NASA Astrophysics Data System (ADS)

Hall, Leonard T.; Hansen, Hedley J.; Abbott, Derek

2004-03-01

Although electronically scanned antenna arrays can provide effective mm-wave search radar sensors, their high cost and complexity are leading to the consideration of alternative beam-forming arrangements. Rotman lenses offer a compact, rugged, reliable, alternative solution. This paper considers the design of a microstrip based Rotman lens for high-resolution, frequency-controlled scanning applications. Its implementation in microstrip is attractive because this technology is low-cost, conformal, and lightweight. A sensor designed for operation at 77 GHz is presented and an ~80° azimuthal scan over a 30 GHz bandwidth is demonstrated.

Fringe field switching AMLCD technology in military and consumer applications

NASA Astrophysics Data System (ADS)

Niemczyk, James

2006-05-01

American Panel Corporation (APC) designs and delivers customized AMLCD products for aircraft cockpits and rugged ground vehicles. APC specifies AMLCD's to be designed and manufactured, based on an exclusive relationship, with both LG.Philips LCD, in South Korea and BOE Hydis, in South Korea. This paper addresses the Fringe Field Switching (FFS) technology developed by BOE Hydis and APC's customization of this technology into both high end avionics display products as well as consumer display products. FFS technology optimizes all optical and electrical performance qualities into a single product. APC offers the high temperature FFS products for all applications.

Multiorder etalon sounder (MOES) development and test for balloon experiment

NASA Technical Reports Server (NTRS)

Hays, Paul B.; Wnag, Jinxue; Wu, Jian

1993-01-01

The Fabry-Perot interferometer (FPI), with its high throughput and high spectral resolution has been used in the remote-sensing measurements of the earth's atmospheric composition, winds, and temperatures. The most recent satellite instruments include the Fabry-Perot interferometer flown on the Dynamics Explorer-2 (DE-2), the High Resolution Doppler Imager (HRDI), and the Cryogenic Limb Array Etalon Spectrometer (CLAES) flown on the Upper Atmosphere Research Satellite (UARS). These instruments measure the Doppler line profiles of the emission and absorption of certain atmospheric species (such as atomic oxygen) in the visible and infrared spectral region. The successful space flight of DE-FPI, HRDI, and CLAES on UARS demonstrated the extremely high spectral resolution and ruggedness of the etalon system for the remote sensing of earth and planetary atmospheres. Recently, an innovative FPI focal plane detection technique called the Circle-to-Line Interferometer Optical (CLIO) system was invented at the Space Physics Research Laboratory. The CLIO simplifies the FPI focal plane detection process by converting the circular rings or fringes into a linear pattern similar to that produced by a conventional spectrometer, while retaining the throughput advantage of the etalon interferometer. The combination of FPI and CLIO allows the development of more sensitive Fabry-Perot interferometers in the infrared for the remote sensing of the lower atmospheres of Earth and possibly other planets. The Multiorder Etalon Sounder (MOES), a combination of the rugged etalon and the CLIO, compares very favorably to other space-borne optical instruments in terms of performance versus complexity. The new instrument is expected to be rugged, compact, and very suitable for an operational temperature and moisture sounder. With this technique, the contamination of radiance measurements by emissions of other gases is also minimized. At the Space Physics Research Laboratory (SPRL), the MOES concept and laboratory experiments were worked on for the past several years. Both theoretical studies and laboratory prototype experiments showed that MOES is very competitive compared with other high resolution sounders in terms of complexity and performance and has great potential as a compact and rugged high resolution atmospheric temperature and trace species sounder from the polar platform or the geostationary platform. The logical next step is to convert our laboratory prototype to a balloon instrument, so that field test of MOES can be carried out to prove the feasibility and capability of this new technology. Some of the activities related to the development of MOES for a possible balloon flight demonstration are described. Those research activities include the imaging quality study on the CLIO, the design and construction of a MOES laboratory prototype, the test and calibration of the MOES prototype, and the design of the balloon flight gondola.

Characterization of matrix effects in developing rugged high-throughput LC-MS/MS methods for bioanalysis.

PubMed

Li, Fumin; Wang, Jun; Jenkins, Rand

2016-05-01

There is an ever-increasing demand for high-throughput LC-MS/MS bioanalytical assays to support drug discovery and development. Matrix effects of sofosbuvir (protonated) and paclitaxel (sodiated) were thoroughly evaluated using high-throughput chromatography (defined as having a run time ≤1 min) under 14 elution conditions with extracts from protein precipitation, liquid-liquid extraction and solid-phase extraction. A slight separation, in terms of retention time, between underlying matrix components and sofosbuvir/paclitaxel can greatly alleviate matrix effects. High-throughput chromatography, with proper optimization, can provide rapid and effective chromatographic separation under 1 min to alleviate matrix effects and enhance assay ruggedness for regulated bioanalysis.

A Very Compact, High Speed and Rugged Acousto-Optic Tunable Filter for Wavelength Division Demultiplexing in Fiber Optic Communication Networks. Phase 1

DTIC Science & Technology

1995-06-30

Novel concepts of near-collinear/collinear acousto - optic interactions have been investigated during this SBIR Phase I program. As a result, several...new acousto - optic tunable filters have been built and tested. The program is highlighted by: (1) Design, fabrication and experimental demonstration of...a novel TeO2 near-collinear acousto - optic tunable filter has been designed, fabricated and tested. The device exhibits a 1.29 nm spectral resolution

Fiber optic accelerometer

NASA Technical Reports Server (NTRS)

August, R. R.

1981-01-01

Low-cost, rugged lightweight accelerometer has been developed that converts mechanical motion into digitized optical outputs and is immune to electromagnetic and electrostatic interferences. Instrument can be placed in hostile environment, such as engine under test, and output led out through miscellany of electrical fields, high temperatures, etc., by optic fiber cables to benign environment of test panel. There, digitized optical signals can be converted to electrical signals for use in standard electrical equipment or used directly in optical devices, such as optical digital computer.

A new product for photon-limited imaging

NASA Astrophysics Data System (ADS)

Gonsiorowski, Thomas

1986-01-01

A new commercial low-light imaging detector, the Photon Digitizing Camera (PDC), is based on the PAPA detector developed at Harvard University. The PDC generates (x, y, t)-coordinate data of each detected photoevent. Because the positional address computation is performed optically, very high counting rates are achieved even at full spatial resolution. Careful optomechanical and electronic design results in a compact, rugged detector with superb performance. The PDC will be used for speckle imaging of astronomical sources and other astronomical and low-light applications.

Field Studies of Exercise and Food Deprivation

DTIC Science & Technology

2006-08-01

Metabolic and structural changes in skeletal muscle during hypocaloric dieting . Am J Clin Nutr 1984; 39: 503–513.32 Opstad PK. Alterations in the morning...day 25.1 MJ/day DBW 1.1, 8.6 kg Strenuous activity can be sustained with adequate food and sleepRugged terrain: 28.3, 34.6 MJ/day High fat diet (60...fat) DFM 1.6, 7.0 kg Body composition of subjects converged with common tasks & diet DFFM 0.6, 1.4 kg %BFfinal 12.7, 13.5 (DEXA) Zimbabwean

Field oriented control of induction motors

NASA Technical Reports Server (NTRS)

Burrows, Linda M.; Zinger, Don S.; Roth, Mary Ellen

1990-01-01

Induction motors have always been known for their simple rugged construction, but until lately were not suitable for variable speed or servo drives due to the inherent complexity of the controls. With the advent of field oriented control (FOC), however, the induction motor has become an attractive option for these types of drive systems. An FOC system which utilizes the pulse population modulation method to synthesize the motor drive frequencies is examined. This system allows for a variable voltage to frequency ratio and enables the user to have independent control of both the speed and torque of an induction motor. A second generation of the control boards were developed and tested with the next point of focus being the minimization of the size and complexity of these controls. Many options were considered with the best approach being the use of a digital signal processor (DSP) due to its inherent ability to quickly evaluate control algorithms. The present test results of the system and the status of the optimization process using a DSP are discussed.

Interactive (statistical) visualisation and exploration of a billion objects with vaex

NASA Astrophysics Data System (ADS)

Breddels, M. A.

2017-06-01

With new catalogues arriving such as the Gaia DR1, containing more than a billion objects, new methods of handling and visualizing these data volumes are needed. We show that by calculating statistics on a regular (N-dimensional) grid, visualizations of a billion objects can be done within a second on a modern desktop computer. This is achieved using memory mapping of hdf5 files together with a simple binning algorithm, which are part of a Python library called vaex. This enables efficient exploration or large datasets interactively, making science exploration of large catalogues feasible. Vaex is a Python library and an application, which allows for interactive exploration and visualization. The motivation for developing vaex is the catalogue of the Gaia satellite, however, vaex can also be used on SPH or N-body simulations, any other (future) catalogues such as SDSS, Pan-STARRS, LSST, etc. or other tabular data. The homepage for vaex is http://vaex.astro.rug.nl.

A magnetic field measurement technique using a miniature transducer

NASA Technical Reports Server (NTRS)

Fales, C. L., Jr.; Breckenridge, R. A.; Debnam, W. J., Jr.

1974-01-01

The development, fabrication, and application of a magnetometer are described. The magnetometer has a miniature transducer and is capable of automatic scanning. The magnetometer described here is capable of detecting static magnetic fields as low as 1.6 A/m and its transducer has an active area 0.64 mm by 0.76 mm. Thin and rugged, the transducer uses wire, 0.05 mm in diameter, which is plated with a magnetic film, enabling measurement of transverse magnetic fields as close as 0.08 mm from a surface. The magnetometer, which is simple to operate and has a fast response, uses an inexpensive clip-on milliammeter (commonly found in most laboratories) for driving and processing the electrical signals and readout. A specially designed transducer holding mechanism replaces the XY recorder ink pen; this mechanism provides the basis for an automatic scanning technique. The instrument has been applied to the measurements of magnetic fields arising from remanent magnetization in experimental plated-wire memory planes and regions of magnetic activity in geological rock specimens.

QuEChERS Purification Combined with Ultrahigh-Performance Liquid Chromatography Tandem Mass Spectrometry for Simultaneous Quantification of 25 Mycotoxins in Cereals.

PubMed

Sun, Juan; Li, Weixi; Zhang, Yan; Hu, Xuexu; Wu, Li; Wang, Bujun

2016-12-15

A method based on the QuEChERS (quick, easy, cheap, effective, rugged, and safe) purification combined with ultrahigh performance liquid chromatography tandem mass spectrometry (UPLC-MS/MS), was optimized for the simultaneous quantification of 25 mycotoxins in cereals. Samples were extracted with a solution containing 80% acetonitrile and 0.1% formic acid, and purified with QuEChERS before being separated by a C18 column. The mass spectrometry was conducted by using positive electrospray ionization (ESI+) and multiple reaction monitoring (MRM) models. The method gave good linear relations with regression coefficients ranging from 0.9950 to 0.9999. The detection limits ranged from 0.03 to 15.0 µg·kg -1 , and the average recovery at three different concentrations ranged from 60.2% to 115.8%, with relative standard deviations (RSD%) varying from 0.7% to 19.6% for the 25 mycotoxins. The method is simple, rapid, accurate, and an improvement compared with the existing methods published so far.

A Personnel Launch System for safe and efficient manned operations

NASA Astrophysics Data System (ADS)

Petro, Andrew J.; Andrews, Dana G.; Wetzel, Eric D.

1990-10-01

Several Conceptual designs for a simple, rugged Personnel Launch System (PLS) are presented. This system could transport people to and from Low Earth Orbit (LEO) starting in the late 1990's using a new modular Advanced Launch System (ALS) developed for the Space Exploration Initiative (SEI). The PLS is designed to be one element of a new space transportation architecture including heavy-lift cargo vehicles, lunar transfer vehicles, and multiple-role spcecraft such as the current Space Shuttle. The primary role of the PLS would be to deliver crews embarking on lunar or planetary missions to the Space Station, but it would also be used for earth-orbit sortie missions, space rescue missions, and some satellite servicing missions. The PLS design takes advantage of emerging electronic and structures technologies to offer a robust vehicle with autonomous operating and quick turnaround capabilities. Key features include an intact abort capability anywhere in the operating envelope, and elimination of all toxic propellants to streamline ground operations.

The North American Breeding Bird Survey

USGS Publications Warehouse

Bystrak, D.; Ralph, C. John; Scott, J. Michael

1981-01-01

A brief history of the North American Breeding Bird Survey (BBS) and a discussion of the technique are presented. The approximately 2000 random roadside routes conducted yearly during the breeding season throughout North America produce an enormous bank of data on distribution and abundance of breeding birds with great potential use. Data on about one million total birds of 500 species per year are on computer tape to facilitate accessibility and are available to any serious investigator. The BBS includes the advantages of wide geographic coverage, sampling of most habitat types, standardization of data collection, and a relatively simple format. The Survey is limited by placement of roads (e.g., marshes and rugged mountainous areas are not well sampled), traffic noise interference in some cases and preference of some bird species for roadside habitats. These and other problems and biases of the BBS are discussed. The uniformity of the technique allows for detecting changes in populations and for creation of maps of relative abundance. Examples of each are presented.

Coherent Lidar Activities at NASA Langley Research Center

NASA Technical Reports Server (NTRS)

Kavaya, Michael J.; Amzajerdian, Farzin; Koch, Grady J.; Singh, Upendra N.; Yu, Jirong

2007-01-01

NASA Langley Research Center has been developing and using coherent lidar systems for many years. The current projects at LaRC are the Global Wind Observing Sounder (GWOS) mission preparation, the Laser Risk Reduction Program (LRRP), the Instrument Incubator Program (IIP) compact, rugged Doppler wind lidar project, the Autonomous precision Landing and Hazard detection and Avoidance Technology (ALHAT) project for lunar landing, and the Skywalker project to find and use thermals to extend UAV flight time. These five projects encompass coherent lidar technology development; characterization, validation, and calibration facilities; compact, rugged packaging; computer simulation; trade studies; data acquisition, processing, and display development; system demonstration; and space mission design. This paper will further discuss these activities at LaRC.

A comparison of home care clients and nursing home residents: can community based care keep the elderly and disabled at home?

PubMed

Shugarman, L R; Fries, B E; James, M

1999-01-01

Admission cohorts from the Michigan Medicaid Home and Community-Based Waiver program and Ohio nursing homes were compared on measures of resource utilization including a modified Resource Utilization Groups (RUG-III) system, Activities of Daily Living (ADLs), and overall case mix. We found that, contrary to previous research, the two samples were remarkably similar across RUG-III categories. However, the nursing home sample was more functionally impaired on measures of ADL functioning and overall case mix. Results of this study may inform policymakers and providers of the potential for maintaining the appropriate population in the home with government-funded home care.

Oman-India pipeline sets survey challenges. Crossing involves most rugged terrain, water depths four times greater than previous attempts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Flynn, J.

1995-02-01

Decisions concerning the route for the world`s deepest pipeline call for some of the most challenging commercial oceanographic and engineering surveys ever undertaken. Oman Oil Co.`s 1, 170-kilometer pipeline will carry 2 billion cubic feet of gas daily across the Arabian Sea from Oman to the northern coast of India at the Gulf of Kutch. Not only will the project be in water depths four times greater than any previous pipeline, but it will cross some of the world`s most rugged seabed terrain, traversing ridges and plunging into deep canyons. Project costs are likely to approach $5 billion.

Sound field measurement in a double layer cavitation cluster by rugged miniature needle hydrophones.

PubMed

Koch, Christian

2016-03-01

During multi-bubble cavitation the bubbles tend to organize themselves into clusters and thus the understanding of properties and dynamics of clustering is essential for controlling technical applications of cavitation. Sound field measurements are a potential technique to provide valuable experimental information about the status of cavitation clouds. Using purpose-made, rugged, wide band, and small-sized needle hydrophones, sound field measurements in bubble clusters were performed and time-dependent sound pressure waveforms were acquired and analyzed in the frequency domain up to 20 MHz. The cavitation clusters were synchronously observed by an electron multiplying charge-coupled device (EMCCD) camera and the relation between the sound field measurements and cluster behaviour was investigated. Depending on the driving power, three ranges could be identified and characteristic properties were assigned. At low power settings no transient and no or very low stable cavitation activity can be observed. The medium range is characterized by strong pressure peaks and various bubble cluster forms. At high power a stable double layer was observed which grew with further increasing power and became quite dynamic. The sound field was irregular and the fundamental at driving frequency decreased. Between the bubble clouds completely different sound field properties were found in comparison to those in the cloud where the cavitation activity is high. In between the sound field pressure amplitude was quite small and no collapses were detected. Copyright © 2015. Published by Elsevier B.V.

A Full View of Pluto Stunning Crescent

NASA Image and Video Library

2015-10-29

In September, NASA's New Horizons team released a stunning but incomplete image of Pluto's crescent. Thanks to new processing work by the science team, New Horizons is releasing the entire, breathtaking image of Pluto. This image was made just 15 minutes after New Horizons' closest approach to Pluto on July 14, 2015, as the spacecraft looked back at Pluto toward the sun. The wide-angle perspective of this view shows the deep haze layers of Pluto's atmosphere extending all the way around Pluto, revealing the silhouetted profiles of rugged plateaus on the night (left) side. The shadow of Pluto cast on its atmospheric hazes can also be seen at the uppermost part of the disk. On the sunlit side of Pluto (right), the smooth expanse of the informally named icy plain Sputnik Planum is flanked to the west (above, in this orientation) by rugged mountains up to 11,000 feet (3,500 meters) high, including the informally named Norgay Montes in the foreground and Hillary Montes on the skyline. Below (east) of Sputnik, rougher terrain is cut by apparent glaciers. The backlighting highlights more than a dozen high-altitude layers of haze in Pluto's tenuous atmosphere. The horizontal streaks in the sky beyond Pluto are stars, smeared out by the motion of the camera as it tracked Pluto. The image was taken with New Horizons' Multi-spectral Visible Imaging Camera (MVIC) from a distance of 11,000 miles (18,000 kilometers) to Pluto. The resolution is 700 meters (0.4 miles).

Compact liquid crystal waveguide based fourier transform spectrometer for in-situ and remote gas and chemical sensing

NASA Astrophysics Data System (ADS)

Chao, Tien-Hsin; Davis, Scott R.; Rommel, Scott D.; Farca, George; Luey, Ben; Martin, Alan; Anderson, Michael H.

2009-11-01

Jet Propulsion Lab and Vescent Photonics Inc. are jointly developing an innovative ultra-compact (volume < 10 cm3), ultra-low power (<10-3 Watt-hours per measurement and zero power consumption when not measuring), completely nonmechanical electro-optic Fourier transform spectrometers (EO-FTS) that will be suitable for a variety of remoteplatform, in-situ measurements. This EO-FTS consists of: i) a novel electro-evanescent waveguide architecture as the solid-state time delay device whose optical path difference (OPD) can be precisely varied utilizing voltage control, ii) a photodetector diode, and iii) an external light/sample collecting devices tailored for either in-situ gas and/or rock sample analysis or for remote atmospheric gas analysis. These devices are made possible by a novel electro-evanescent waveguide architecture, enabling "chip-scale" EO-FTS sensors. The potential performance of these EO-FTS sensors include: i) a spectral range throughout 0.4-5 μm (25000 - 2000 cm-1), ii) high-resolution ▵λ <= 0.1 nm), iii) high-speed (< 1 ms) measurements, and iv) rugged integrated optical construction. This performance potential enables the detection and quantification of a large number of different atmospheric gases simultaneously in the same air mass and the rugged construction will enable deployment on previously inaccessible platforms. In this paper, the up-to-date EO-FTS sensor development status will be presented; initial experimental results will also be demonstrated.

Fresnel zone plate light field spectral imaging simulation

NASA Astrophysics Data System (ADS)

Hallada, Francis D.; Franz, Anthony L.; Hawks, Michael R.

2017-05-01

Through numerical simulation, we have demonstrated a novel snapshot spectral imaging concept using binary diffractive optics. Binary diffractive optics, such as Fresnel zone plates (FZP) or photon sieves, can be used as the single optical element in a spectral imager that conducts both imaging and dispersion. In previous demonstrations of spectral imaging with diffractive optics, the detector array was physically translated along the optic axis to measure different image formation planes. In this new concept the wavelength-dependent images are constructed synthetically, by using integral photography concepts commonly applied to light field (plenoptic) cameras. Light field cameras use computational digital refocusing methods after exposure to make images at different object distances. Our concept refocuses to make images at different wavelengths instead of different object distances. The simulations in this study demonstrate this concept for an imager designed with a FZP. Monochromatic light from planar sources is propagated through the system to a measurement plane using wave optics in the Fresnel approximation. Simple images, placed at optical infinity, are illuminated by monochromatic sources and then digitally refocused to show different spectral bins. We show the formation of distinct images from different objects, illuminated by monochromatic sources in the VIS/NIR spectrum. Additionally, this concept could easily be applied to imaging in the MWIR and LWIR ranges. In conclusion, this new type of imager offers a rugged and simple optical design for snapshot spectral imaging and warrants further development.

Using wind fields from a high resolution atmospheric model for simulating snow dynamics in mountainous terrain

NASA Astrophysics Data System (ADS)

Bernhardt, M.; Strasser, U.; Zängl, G.; Mauser, W.; Liston, G.; Pohl, S.

2008-12-01

Wind-induced snow transport processes lead to a significant variability of the snow cover. Knowledge about this variability is important for e.g. determining the temporal dynamics of the snowmelt runoff. For predicting the correct amount of transported snow knowledge of the local wind-field is an essential. In high-alpine rugged relief wind fields can hardly be provided by a simple interpolation of station recordings. In this work we use a modified version of the PSU/NCAR Mesoscale Model MM5 to derive wind fields for a 450 km² area at a target resolution of 200 m, accounting for topography and related dynamic effects. We have modelled 220 wind fields representing the most characteristic wind situations within the test-area. The criteria for the extraction of the wind field for the current snowmodel (SNOWTRAND-3D) time step are mean wind speeds and directions in the 700 hPa level derived from DWD (German Weather Service) Local Model reanalysis data with a temporal resolution of one hour. These data are then compared with the corresponding mean wind speeds and directions from the appropriate MM5 nesting area indicating which one of the library files represents the best fit. Verification is conducted by comparison of historical station measurements with corresponding downscaled simulation results. For this downscaling a semi-empirical approach is utilized which accounts for topographic effects. Results for the winter seasons 2003/04 and 2004/05 showing that the presented scheme is able to improve the quality of SNOWTRAN-3D runs with respect to the snow height.

Simple and fast analysis of tetrabromobisphenol A, hexabromocyclododecane isomers, and polybrominated diphenyl ethers in serum using solid-phase extraction or QuEChERS extraction followed by tandem mass spectrometry coupled to HPLC and GC.

PubMed

Li, Jian; Chen, Tian; Wang, Yuwei; Shi, Zhixiong; Zhou, Xianqing; Sun, Zhiwei; Wang, Dejun; Wu, Yongning

2017-02-01

Two simplified sample preparation procedures for simultaneous extraction and clean-up of tetrabromobisphenol A, α-, β-, and γ-hexabromocyclododecane and polybrominated diphenyl ethers in human serum were developed and validated. The first procedure was based on solid-phase extraction. Sample extraction, purification, and lipid removal were carried out directly on an Oasis HLB cartridge. The second procedure was a quick, easy, cheap, effective, rugged, and safe-based approach using octadecyl-modified silica particles as a sorbent. After sample extraction and cleanup, tetrabromobisphenol A/hexabromocyclododecane was separated from polybrominated diphenyl ethers by using a Si-based cartridge. Tetrabromobisphenol A and hexabromocyclododecane were then detected by high-performance liquid chromatography coupled to tandem mass spectrometry, while polybrominated diphenyl ethers were detected by gas chromatography coupled to tandem mass spectrometry. The results of the spike recovery test using fetal bovine serum showed that the average recoveries of the analytes ranged from 87.3 to 115.3% with relative standard deviations equal to or lower than 13.4 %. Limits of detection of the analytes were in the range of 0.4-19 pg/mL except for decabromodiphenyl ether. The developed method was successfully applied to routine analysis of human serum samples from occupational workers and the general population. Extremely high serum polybrominated diphenyl ethers levels up to 3.32 × 10 4 ng/g lipid weight were found in occupational workers. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Trace analysis of multi-class pesticide residues in Chinese medicinal health wines using gas chromatography with electron capture detection

PubMed Central

Kong, Wei-Jun; Liu, Qiu-Tao; Kong, Dan-Dan; Liu, Qian-Zhen; Ma, Xin-Ping; Yang, Mei-Hua

2016-01-01

A method is described for multi-residue, high-throughput determination of trace levels of 22 organochlorine pesticides (OCPs) and 5 pyrethroid pesticides (PYPs) in Chinese medicinal (CM) health wines using a QuEChERS (quick, easy, cheap, effective, rugged, and safe) based extraction method and gas chromatography-electron capture detection (GC-ECD). Several parameters were optimized to improve preparation and separation time while still maintaining high sensitivity. Validation tests of spiked samples showed good linearities for 27 pesticides (R = 0.9909–0.9996) over wide concentration ranges. Limits of detection (LODs) and quantification (LOQs) were measured at ng/L levels, 0.06–2 ng/L and 0.2–6 ng/L for OCPs and 0.02–3 ng/L and 0.06–7 ng/L for PYPs, respectively. Inter- and intra-day precision tests showed variations of 0.65–9.89% for OCPs and 0.98–13.99% for PYPs, respectively. Average recoveries were in the range of 47.74–120.31%, with relative standard deviations below 20%. The developed method was then applied to analyze 80 CM wine samples. Beta-BHC (Benzene hexachloride) was the most frequently detected pesticide at concentration levels of 5.67–31.55 mg/L, followed by delta-BHC, trans-chlordane, gamma-BHC, and alpha-BHC. The validated method is simple and economical, with adequate sensitivity for trace levels of multi-class pesticides. It could be adopted by laboratories for this and other types of complex matrices analysis. PMID:26883080

Trace analysis of multi-class pesticide residues in Chinese medicinal health wines using gas chromatography with electron capture detection

NASA Astrophysics Data System (ADS)

Kong, Wei-Jun; Liu, Qiu-Tao; Kong, Dan-Dan; Liu, Qian-Zhen; Ma, Xin-Ping; Yang, Mei-Hua

2016-02-01

A method is described for multi-residue, high-throughput determination of trace levels of 22 organochlorine pesticides (OCPs) and 5 pyrethroid pesticides (PYPs) in Chinese medicinal (CM) health wines using a QuEChERS (quick, easy, cheap, effective, rugged, and safe) based extraction method and gas chromatography-electron capture detection (GC-ECD). Several parameters were optimized to improve preparation and separation time while still maintaining high sensitivity. Validation tests of spiked samples showed good linearities for 27 pesticides (R = 0.9909-0.9996) over wide concentration ranges. Limits of detection (LODs) and quantification (LOQs) were measured at ng/L levels, 0.06-2 ng/L and 0.2-6 ng/L for OCPs and 0.02-3 ng/L and 0.06-7 ng/L for PYPs, respectively. Inter- and intra-day precision tests showed variations of 0.65-9.89% for OCPs and 0.98-13.99% for PYPs, respectively. Average recoveries were in the range of 47.74-120.31%, with relative standard deviations below 20%. The developed method was then applied to analyze 80 CM wine samples. Beta-BHC (Benzene hexachloride) was the most frequently detected pesticide at concentration levels of 5.67-31.55 mg/L, followed by delta-BHC, trans-chlordane, gamma-BHC, and alpha-BHC. The validated method is simple and economical, with adequate sensitivity for trace levels of multi-class pesticides. It could be adopted by laboratories for this and other types of complex matrices analysis.

[Determination of three exogenous plant hormone residues in bean sprout by high performance liquid chromatography-quadrupole-time of flight mass spectrometry].

PubMed

Xie, Hanbing; Zhou, Mingying; Zhao, Haifeng; Wang, Yigang; Jiang, Wanfeng; Zhao, Shan

2014-05-01

This study was aimed to the establishment of an analytical method for the determination of three exogenous plant hormone residues in bean sprout by high performance liquid chromatography-quadrupole-time of flight mass spectrometry (HPLC-Q-TOF-MS). The target compounds were gibberellins, 6-benzylaminopurine and parachlorophenoxyacetic acid. The QuEChERS (quick, easy, cheap, effective, rugged, and safe) method was used for sample preparation. The analytes were extracted with a solution containing 1% (v/v, if not specified) acetic, 50% ethanol, 49% acetonitrile, and cleaned-up by dispersive solid-phase extraction with diatomite dispersant, then degreased by hexane. The three target compounds were separated on an Eclipse Plus C18 column (100 mm x 3.0 mm, 1.8 microm) with mobile phases A (water containing 0.1% formic acid) and B (methanol) by gradient elution within 15 min, and detected under negative electrospray ionization (ESI) mode. The quantitative analysis was carried out by extracting the peak area with accurate mass. The confirmatory analysis of the target compounds was performed with the qualitative fragments. The results showed that the limits of quantification (LOQs, S/N = 10) for the three target compounds were from 5.0 microg/kg to 10 microg/kg. The respective mean recoveries were found to be in the range of 79.1%-96.1%, and the RSDs were 5.7%-10.4%. It was applicable to the analysis of the three exogenous plant hormones in bean sprout samples. This method is simple, fast and efficient.

Scanned-wavelength diode laser sensors for harsh environments

NASA Astrophysics Data System (ADS)

Jeffries, Jay B.; Sanders, Scott T.; Zhou, Xin; Ma, Lin; Mattison, Daniel W.; Hanson, Ronald K.

2002-09-01

Diode laser absorption offers the possibility of high-speed, robust, and rugged sensors for a wide variety of practical applications. Pressure broadening complicates absorption measurements of gas temperature and species concentrations in high-pressure, high-temperature practical environments. More agile wavelength scanning can enable measurements of temperature and species concentrations in flames and engines as demonstrated by example measurements using wavelength scanning of a single DFB in laboratory flames or a vertical cavity surface emitting laser (VCSEL) in a pulse detonation engine environment. Although the blending of multiple transitions by pressure broadening complicates the atmospheric pressure spectrum of C2H4 fuel, a scanned wavelength strategy enables quantitative measurement of fuel/oxidizer stoichiometry. Wavelength-agile scanning techniques enable high-speed measurements in these harsh environments.

Fundamentals of electric power conversion

DOE Office of Scientific and Technical Information (OSTI.GOV)

Umans, S.D.

1992-12-01

Its rugged nature and straightforward design make the induction motor the most commonly used type of electric motor. This motor ranges in size from the fractional-horsepower, single-phase motors found in household appliances to polyphase motors rated at thousands of horsepower for industrial applications. Volume 1 of this report describes the function of induction motors, their characteristics, and induction motor testing. Volume 2 describes the characteristics of high-efficiency induction motors, with emphasis on the techniques used to obtain high efficiency. This two-volume report is written in nontechnical language and is intended for readers who require background from an applications, marketing, motormore » planning, or managerial perspective.« less

Fundamentals of electric power conversion

DOE Office of Scientific and Technical Information (OSTI.GOV)

Umans, S.D.

1992-12-01

Its rugged nature and straightforward design make the induction motor the most commonly used type of electric motor. This motor ranges in size fro the fractional-horsepower, single-phase motors found in household appliances to polyphase motors rated at thousands of horsepower for industrial applications. Volume 1 of this report describes the function of induction motors, their characteristics, and induction motor testing. Volume 2 describes the characteristics of high-efficiency induction motors, with emphasis on the techniques used to obtain high efficiency. This two-volume report is written in nontechnical language and is intended for readers who require background from applications, marketing, motor planning,more » or managerial perspective.« less

Multi-threshold de-noising of electrical imaging logging data based on the wavelet packet transform

NASA Astrophysics Data System (ADS)

Xie, Fang; Xiao, Chengwen; Liu, Ruilin; Zhang, Lili

2017-08-01

A key problem of effectiveness evaluation for fractured-vuggy carbonatite reservoir is how to accurately extract fracture and vug information from electrical imaging logging data. Drill bits quaked during drilling and resulted in rugged surfaces of borehole walls and thus conductivity fluctuations in electrical imaging logging data. The occurrence of the conductivity fluctuations (formation background noise) directly affects the fracture/vug information extraction and reservoir effectiveness evaluation. We present a multi-threshold de-noising method based on wavelet packet transform to eliminate the influence of rugged borehole walls. The noise is present as fluctuations in button-electrode conductivity curves and as pockmarked responses in electrical imaging logging static images. The noise has responses in various scales and frequency ranges and has low conductivity compared with fractures or vugs. Our de-noising method is to decompose the data into coefficients with wavelet packet transform on a quadratic spline basis, then shrink high-frequency wavelet packet coefficients in different resolutions with minimax threshold and hard-threshold function, and finally reconstruct the thresholded coefficients. We use electrical imaging logging data collected from fractured-vuggy Ordovician carbonatite reservoir in Tarim Basin to verify the validity of the multi-threshold de-noising method. Segmentation results and extracted parameters are shown as well to prove the effectiveness of the de-noising procedure.

Constellation-X Microcalorimeter Development

NASA Technical Reports Server (NTRS)

Kelly, Richard (Technical Monitor); Silver, Eric

2004-01-01

Discussion topics: Review concept for NTD array construction. Tested revised fabrication tique: simpler construction; more rugged; and easier to control thermal properties. Development status. Related cryogenic infrastructure.

On Shaft Data Acquisition System (OSDAS)

NASA Technical Reports Server (NTRS)

Pedings, Marc; DeHart, Shawn; Formby, Jason; Naumann, Charles

2012-01-01

On Shaft Data Acquisition System (OSDAS) is a rugged, compact, multiple-channel data acquisition computer system that is designed to record data from instrumentation while operating under extreme rotational centrifugal or gravitational acceleration forces. This system, which was developed for the Heritage Fuel Air Turbine Test (HFATT) program, addresses the problem of recording multiple channels of high-sample-rate data on most any rotating test article by mounting the entire acquisition computer onboard with the turbine test article. With the limited availability of slip ring wires for power and communication, OSDAS utilizes its own resources to provide independent power and amplification for each instrument. Since OSDAS utilizes standard PC technology as well as shared code interfaces with the next-generation, real-time health monitoring system (SPARTAA Scalable Parallel Architecture for Real Time Analysis and Acquisition), this system could be expanded beyond its current capabilities, such as providing advanced health monitoring capabilities for the test article. High-conductor-count slip rings are expensive to purchase and maintain, yet only provide a limited number of conductors for routing instrumentation off the article and to a stationary data acquisition system. In addition to being limited to a small number of instruments, slip rings are prone to wear quickly, and introduce noise and other undesirable characteristics to the signal data. This led to the development of a system capable of recording high-density instrumentation, at high sample rates, on the test article itself, all while under extreme rotational stress. OSDAS is a fully functional PC-based system with 48 channels of 24-bit, high-sample-rate input channels, phase synchronized, with an onboard storage capacity of over 1/2-terabyte of solid-state storage. This recording system takes a novel approach to the problem of recording multiple channels of instrumentation, integrated with the test article itself, packaged in a compact/rugged form factor, consuming limited power, all while rotating at high turbine speeds.

Geometric and radiometric preprocessing of airborne visible/infrared imaging spectrometer (AVIRIS) data in rugged terrain for quantitative data analysis

NASA Technical Reports Server (NTRS)

Meyer, Peter; Green, Robert O.; Staenz, Karl; Itten, Klaus I.

1994-01-01

A geocoding procedure for remotely sensed data of airborne systems in rugged terrain is affected by several factors: buffeting of the aircraft by turbulence, variations in ground speed, changes in altitude, attitude variations, and surface topography. The current investigation was carried out with an Airborne Visible/Infrared Imaging Spectrometer (AVIRIS) scene of central Switzerland (Rigi) from NASA's Multi Aircraft Campaign (MAC) in Europe (1991). The parametric approach reconstructs for every pixel the observation geometry based on the flight line, aircraft attitude, and surface topography. To utilize the data for analysis of materials on the surface, the AVIRIS data are corrected to apparent reflectance using algorithms based on MODTRAN (moderate resolution transfer code).

Recent progress of flexible AMOLED displays

NASA Astrophysics Data System (ADS)

Pang, Huiqing; Rajan, Kamala; Silvernail, Jeff; Mandlik, Prashant; Ma, Ruiqing; Hack, Mike; Brown, Julie J.; Yoo, Juhn S.; Jung, Sang-Hoon; Kim, Yong-Cheol; Byun, Seung-Chan; Kim, Jong-Moo; Yoon, Soo-Young; Kim, Chang-Dong; Hwang, Yong-Kee; Chung, In-Jae; Fletcher, Mark; Green, Derek; Pangle, Mike; McIntyre, Jim; Smith, Randal D.

2011-03-01

Significant progress has been made in recent years in flexible AMOLED displays and numerous prototypes have been demonstrated. Replacing rigid glass with flexible substrates and thin-film encapsulation makes displays thinner, lighter, and non-breakable - all attractive features for portable applications. Flexible AMOLEDs equipped with phosphorescent OLEDs are considered one of the best candidates for low-power, rugged, full-color video applications. Recently, we have demonstrated a portable communication display device, built upon a full-color 4.3-inch HVGA foil display with a resolution of 134 dpi using an all-phosphorescent OLED frontplane. The prototype is shaped into a thin and rugged housing that will fit over a user's wrist, providing situational awareness and enabling the wearer to see real-time video and graphics information.

Stable and rugged etalon for the Dynamics Explorer Fabry-Perot interferometer. 1: Design and construction.

PubMed

Rees, D; Fuller-Rowell, T J; Lyons, A; Killeen, T L; Hays, P B

1982-11-01

This is one of two papers which describe the development and performance of a very stable and rugged etalon designed for use in the Fabry-Perot interferometer, one of the instruments of the NASA Dynamics Explorer satellite mission, and which will obtain global measurements of the thermospheric and mesospheric wind and temperature with an accuracy of aporoximately 10 m/sec. The etalon consists of two flat plates of fused silica, with spacers constructed of Zerodur (a polycrystalline glass ceramic of extremely low expansion coefficient) which are cemented together using cyanoacrylic adhesives. This provides adequate mechanical integrity and stability for any space flight application and has a thermal expansion coefficient of the etalon cavity of <10(-7)/ degrees C.

Robust, Thin Optical Films for Extreme Environments

NASA Technical Reports Server (NTRS)

2006-01-01

The environment of space presents scientists and engineers with the challenges of a harsh, unforgiving laboratory in which to conduct their scientific research. Solar astronomy and X-ray astronomy are two of the more challenging areas into which NASA scientists delve, as the optics for this high-tech work must be extremely sensitive and accurate, yet also be able to withstand the battering dished out by radiation, extreme temperature swings, and flying debris. Recent NASA work on this rugged equipment has led to the development of a strong, thin film for both space and laboratory use.

3D display considerations for rugged airborne environments

NASA Astrophysics Data System (ADS)

Barnidge, Tracy J.; Tchon, Joseph L.

2015-05-01

The KC-46 is the next generation, multi-role, aerial refueling tanker aircraft being developed by Boeing for the United States Air Force. Rockwell Collins has developed the Remote Vision System (RVS) that supports aerial refueling operations under a variety of conditions. The system utilizes large-area, high-resolution 3D displays linked with remote sensors to enhance the operator's visual acuity for precise aerial refueling control. This paper reviews the design considerations, trade-offs, and other factors related to the selection and ruggedization of the 3D display technology for this military application.

Characterization of silicon carbide and diamond detectors for neutron applications

NASA Astrophysics Data System (ADS)

Hodgson, M.; Lohstroh, A.; Sellin, P.; Thomas, D.

2017-10-01

The presence of carbon atoms in silicon carbide and diamond makes these materials ideal candidates for direct fast neutron detectors. Furthermore the low atomic number, strong covalent bonds, high displacement energies, wide bandgap and low intrinsic carrier concentrations make these semiconductor detectors potentially suitable for applications where rugged, high-temperature, low-gamma-sensitivity detectors are required, such as active interrogation, electronic personal neutron dosimetry and harsh environment detectors. A thorough direct performance comparison of the detection capabilities of semi-insulating silicon carbide (SiC-SI), single crystal diamond (D-SC), polycrystalline diamond (D-PC) and a self-biased epitaxial silicon carbide (SiC-EP) detector has been conducted and benchmarked against a commercial silicon PIN (Si-PIN) diode, in a wide range of alpha (Am-241), beta (Sr/Y-90), ionizing photon (65 keV to 1332 keV) and neutron radiation fields (including 1.2 MeV to 16.5 MeV mono-energetic neutrons, as well as neutrons from AmBe and Cf-252 sources). All detectors were shown to be able to directly detect and distinguish both the different radiation types and energies by using a simple energy threshold discrimination method. The SiC devices demonstrated the best neutron energy discrimination ratio (E\\max (n=5 MeV)/E\\max (n=1 MeV)  ≈5), whereas a superior neutron/photon cross-sensitivity ratio was observed in the D-PC detector (E\\max (AmBe)/E\\max (Co-60)  ≈16). Further work also demonstrated that the cross-sensitivity ratios can be improved through use of a simple proton-recoil conversion layer. Stability issues were also observed in the D-SC, D-PC and SiC-SI detectors while under irradiation, namely a change of energy peak position and/or count rate with time (often referred to as the polarization effect). This phenomenon within the detectors was non-debilitating over the time period tested (> 5 h) and, as such, stable operation was possible. Furthermore, the D-SC, self-biased SiC-EP and semi-insulating SiC detectors were shown to operate over the temperature range -60 °C to +100 °C.

Multiclass mycotoxin analysis in edible oils using a simple solvent extraction method and liquid chromatography with tandem mass spectrometry.

PubMed

Eom, Taeyong; Cho, Hyun-Deok; Kim, Junghyun; Park, Mihee; An, Jinyoung; Kim, Moosung; Kim, Sheen-Hee; Han, Sang Beom

2017-11-01

A simple and rapid method for the simultaneous determination of 11 mycotoxins - aflatoxins B 1 , B 2 , G 1 and G 2 ; fumonisins B 1 , B 2 and B 3 ; ochratoxin A; zearalenone; deoxynivalenol; and T-2 toxin - in edible oils was established using liquid chromatography tandem mass spectrometry (LC-MS/MS). In this study, QuEChERS (Quick, Easy, Cheap, Effective, Rugged and Safe), QuEChERS with dispersive liquid-liquid microextraction, and solvent extraction were examined for sample preparation. Among these methods, solvent extraction with a mixture of formic acid/acetonitrile (5/95, v/v) successfully extracted all target mycotoxins. Subsequently, a defatting process using n-hexane was employed to remove the fats present in the edible oil samples. Mass spectrometry was carried out using electrospray ionisation in polarity switching mode with multiple reaction monitoring. The developed LC-MS/MS method was validated by assessing the specificity, linearity, recovery, limit of quantification (LOQ), accuracy and precision with reference to Commission Regulation (EC) 401/2006. Mycotoxin recoveries of 51.6-82.8% were achieved in addition to LOQs ranging from 0.025 ng/g to 1 ng/g. The edible oils proved to be relatively uncomplicated matrices and the developed method was applied to 9 edible oil samples, including soybean oil, corn oil and rice bran oil, to evaluate potential mycotoxin contamination. The levels of detection were significantly lower than the international regulatory standards. Therefore, we expect that our developed method, based on simple, two-step sample preparation process, will be suitable for the large-scale screening of mycotoxin contamination in edible oils.

Fresh from the Ornamental Garden: Hips of Selected Rose Cultivars Rich in Phytonutrients.

PubMed

Cunja, Vlasta; Mikulic-Petkovsek, Maja; Weber, Nika; Jakopic, Jerneja; Zupan, Anka; Veberic, Robert; Stampar, Franci; Schmitzer, Valentina

2016-02-01

Morphological parameters (size, weight, color), the content of sugars, organic acids, lycopene, β-carotene, and phenolics were determined in hips of Rosa canina (RCA), Rosa sweginzowii (RSW), Rosa rugosa (RUG), and selected ornamental Rosa cultivars Fru Dagmar Hastrup (FDH), Repandia (REP), Veilchenblau (RVB), Aloha (RAL), Bonica (BON), and Golden Gate (RGG). Although traditionally used RCA hips contained the highest amount of cyanidin-3-glucoside (83 μg/g DW) and were the reddest (h° = 17.5), they did not stand out in other analyzed parameters. RGG climber had the biggest hips (8.86 g), which also contained highest sugar levels (50.9 g/100 g DW). RAL stood out as the cultivar rich in organic acids (33.9 g/100 g DW), mainly because of high quinic acid content (17.6 g/100g DW). FDH and RSW hips were characterized by particularly high ascorbic acid levels (4325 mg/100 g DW and 4711 mg/100 g DW). Other ornamental cultivars contained low amounts of ascorbic acid compared to the analyzed species. The phenolic profile was species/cultivars-specific. The greatest diversity of phenolic compounds was detected in RUG and FDH hips (55 and 54 different tentatively identified compounds with HPLC/MS). Flavanols represented the main phenolic class in most of the investigated species/cultivars and RGG hips contained the highest amount of catechin and proanthocyandin derivatives (15855 μg/g DW). Altogether RAL hips contained the highest quantity of phenolics (44746 μg/g DW) mainly due to high levels of hydrolysable tannins compared to other species/cultivars. Although small, hips of BON and REP were most abundant regarding β-carotene and lycopene content, respectively. © 2016 Institute of Food Technologists®

Analyzing Water's Optical Absorption

NASA Technical Reports Server (NTRS)

2002-01-01

A cooperative agreement between World Precision Instruments (WPI), Inc., and Stennis Space Center has led the UltraPath(TM) device, which provides a more efficient method for analyzing the optical absorption of water samples at sea. UltraPath is a unique, high-performance absorbance spectrophotometer with user-selectable light path lengths. It is an ideal tool for any study requiring precise and highly sensitive spectroscopic determination of analytes, either in the laboratory or the field. As a low-cost, rugged, and portable system capable of high- sensitivity measurements in widely divergent waters, UltraPath will help scientists examine the role that coastal ocean environments play in the global carbon cycle. UltraPath(TM) is a trademark of World Precision Instruments, Inc. LWCC(TM) is a trademark of World Precision Instruments, Inc.

Real-Time Optical Fuel-to-Air Ratio Sensor for Gas Turbine Combustors

NASA Technical Reports Server (NTRS)

Nguyen, Quang-Viet; Mongia, Rajiv K.; Dibble, Robert W.

1999-01-01

The measurement of the temporal distribution of fuel in gas turbine combustors is important in considering pollution, combustion efficiency and combustor dynamics and acoustics. Much of the previous work in measuring fuel distributions in gas turbine combustors has focused on the spatial aspect of the distribution. The temporal aspect however, has often been overlooked, even though it is just as important. In part, this is due to the challenges of applying real-time diagnostic techniques in a high pressure and high temperature environment. A simple and low-cost instrument that non-intrusively measures the real-time fuel-to-air ratio (FAR) in a gas turbine combustor has been developed. The device uses a dual wavelength laser absorption technique to measure the concentration of most hydrocarbon fuels such as jet fuel, methane, propane, etc. The device can be configured to use fiber optics to measure the local FAR inside a high pressure test rig without the need for windows. Alternatively, the device can readily be used in test rigs that have existing windows without modifications. An initial application of this instrument was to obtain time-resolved measurements of the FAR in the premixer of a lean premixed prevaporized (LPP) combustor at inlet air pressures and temperatures as high as 17 atm at 800 K, with liquid JP-8 as the fuel. Results will be presented that quantitatively show the transient nature of the local FAR inside a LPP gas turbine combustor at actual operating conditions. The high speed (kHz) time resolution of this device, combined with a rugged fiber optic delivery system, should enable the realization of a flight capable active-feedback and control system for the abatement of noise and pollutant emissions in the future. Other applications that require an in-situ and time-resolved measurement of fuel vapor concentrations should also find this device to be of use.

Wireless telemetry system for floating bodies

NASA Technical Reports Server (NTRS)

Fain, L. T.; Cribb, H. E.

1974-01-01

Unit includes rugged waterproof cables and equipment containers, low power, sturdy antenna construction, and easy equipment setup and serviceability. Accuracy and reliability of entire measurement system were not sacrificed.

Development and validation of a quick, easy, cheap, effective, rugged and safe method for the determination of imidacloprid and its metabolites in soil.

PubMed

Akoijam, Romila; Singh, Balwinder; Mandal, Kousik

2015-04-01

A simplified quick, easy, cheap, effective, rugged and safe method was standardized and validated for the estimation of residues of imidacloprid and its metabolites from different types of soil comprising sandy loam, loamy sand and clay loam soil. The samples were extracted with acetonitrile, clean up by treatment with primary secondary amine sorbent and graphitized carbon. High-performance liquid chromatography (HPLC) is a technique to separate and quantitate residues of polar, nonvolatile and thermolabile chemical compounds, using high-pressure pumps, short and narrow columns packed with microparticulate phases and a detector. The residues were estimated using HPLC equipped with a photodiode array detector system, C18 column. Acetonitrile and water (30 : 70) were used as an isocratic mobile phase at 0.3 mL/min. Imidacloprid and its metabolites presented distinct peaks at retention factors of 4.93 min (6-chloronicotinic acid), 7.91 min (nitroguanidine), 9.12 min (olefin), 11.32 min (nitrosimine), 13.82 min (urea), 15.45 min (5-hydroxy) and 22.47 min (imidacloprid). Consistent recoveries above 80% for imidacloprid and its metabolites were observed when samples were spiked at 0.01, 0.05 and 0.10 mg/kg levels. The limit of quantification of the method was 0.01 mg/kg. The analytical method was validated in terms of parameters including selectivity, linearity, precision and accuracy of the detection system. © The Author 2014. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

The photon pair source that survived a rocket explosion

PubMed Central

Tang, Zhongkan; Chandrasekara, Rakhitha; Tan, Yue Chuan; Cheng, Cliff; Durak, Kadir; Ling, Alexander

2016-01-01

We report on the performance of a compact photon pair source that was recovered intact from a failed space launch. The source had been embedded in a nanosatellite and was designed to perform pathfinder experiments leading to global quantum communication networks using spacecraft. Despite the launch vehicle explosion soon after takeoff, the nanosatellite was successfully retrieved from the accident site and the source within it was found to be fully operational. We describe the assembly technique for the rugged source. Post-recovery data is compared to baseline measurements collected before the launch attempt and no degradation in brightness or polarization correlation was observed. The survival of the source through an extreme environment provides strong evidence that it is possible to engineer rugged quantum optical systems. PMID:27161541

Harmonic Fourier beads method for studying rare events on rugged energy surfaces.

PubMed

Khavrutskii, Ilja V; Arora, Karunesh; Brooks, Charles L

2006-11-07

We present a robust, distributable method for computing minimum free energy paths of large molecular systems with rugged energy landscapes. The method, which we call harmonic Fourier beads (HFB), exploits the Fourier representation of a path in an appropriate coordinate space and proceeds iteratively by evolving a discrete set of harmonically restrained path points-beads-to generate positions for the next path. The HFB method does not require explicit knowledge of the free energy to locate the path. To compute the free energy profile along the final path we employ an umbrella sampling method in two generalized dimensions. The proposed HFB method is anticipated to aid the study of rare events in biomolecular systems. Its utility is demonstrated with an application to conformational isomerization of the alanine dipeptide in gas phase.

3D laptop for defense applications

NASA Astrophysics Data System (ADS)

Edmondson, Richard; Chenault, David

2012-06-01

Polaris Sensor Technologies has developed numerous 3D display systems using a US Army patented approach. These displays have been developed as prototypes for handheld controllers for robotic systems and closed hatch driving, and as part of a TALON robot upgrade for 3D vision, providing depth perception for the operator for improved manipulation and hazard avoidance. In this paper we discuss the prototype rugged 3D laptop computer and its applications to defense missions. The prototype 3D laptop combines full temporal and spatial resolution display with the rugged Amrel laptop computer. The display is viewed through protective passive polarized eyewear, and allows combined 2D and 3D content. Uses include robot tele-operation with live 3D video or synthetically rendered scenery, mission planning and rehearsal, enhanced 3D data interpretation, and simulation.

High-performance colorimeter with an electronic bubble gate for use in miniaturized continuous-flow analyzers.

PubMed

Neeley, W E; Wardlaw, S C; Yates, T; Hollingsworth, W G; Swinnen, M E

1976-02-01

We describe a high-performance colorimeter with an electronic bubble gate for use with miniaturized continuous-flow analyzers. The colorimeter has a flow-through cuvette with optically flat quartz windows that allows a bubbled stream to pass freely without any breakup or retention of bubbles. The fluid volume in the light path is only 1.8 mul. The electronic bubble gate selectively removes that portion of the photodector signal produced by the air bubbles passing through the flow cell and allows that portion of the signal attributable to the fluid segment to pass to the recorder. The colorimeter is easy to use, rugged, inexpensive, and requires minimal adjustments.

Portable Instrument to Measure CDOM Light Absorption in Aquatic Systems: WPI Success Story

NASA Technical Reports Server (NTRS)

2001-01-01

World Precision Instruments, Inc. (WPI), of Sarasota, FL, in collaboration with NASA's John C. Stennis Space Center, has developed an innovative instrument to accurately measure Colored Dissolved Organic Matter (CDOM) absorption in the field. This successful collaboration has culminated in an exciting new device, called the UltraPath, now commercially available through WPI. Traditional methods of measuring absorption of dissolved materials require special handling and storage prior to measurement. Use of laboratory spectrophotometers as the measuring devices have proven time consuming, cumbersome, and delicate to handle. The UltraPath provides a low-cost, highly sensitive, rugged, portable system that is capable of high sensitivity measurements in widely divergent waters.

Detecting a wide range of environmental contaminants in human blood samples--combining QuEChERS with LC-MS and GC-MS methods.

PubMed

Plassmann, Merle M; Schmidt, Magdalena; Brack, Werner; Krauss, Martin

2015-09-01

Exposure to environmental pollution and consumer products may result in an uptake of chemicals into human tissues. Several studies have reported the presence of diverse environmental contaminants in human blood samples. However, previously developed multi-target methods for the analysis of human blood include a fairly limited amount of compounds stemming from one or two related compound groups. Thus, the sample preparation method QuEChERS (quick easy cheap effective rugged and safe) was tested for the extraction of 64 analytes covering a broad compound domain followed by detection using liquid and gas chromatography coupled to mass spectrometry (LC- and GC-MS). Forty-seven analytes showed absolute recoveries above 70% in the first QuEChERS step, being a simple liquid-liquid extraction (LLE) using acetonitrile and salt. The second QuEChERS step, being a dispersive solid phase extraction, did not result in an overall improvement of recoveries or removal of background signals. Using solely the LLE step, eight analytes could subsequently be detected in human blood samples from the German Environmental Specimen Bank. Using a LC-multiple reaction monitoring (MRM) method with a triple quadrupole instrument, better recoveries were achieved than with an older LC-high-resolution (HR) MS full scan orbitrap instrument, which required a higher concentration factor of the extracts. However, the application of HRMS full scan methods could be used for the detection of additional compounds retrospectively.

Multiresidue method for the determination of 227 pesticides in hot pepper (Capsicum annuum L.) by liquid chromatography with tandem mass spectrometry.

PubMed

Zhu, Yong-Zhe; Zhao, Mei-Ai; Nan Feng, Ya; Han Kim, Jeong

2014-10-01

A high-throughput, rapid, and efficient modified QuEChERS (quick, easy, cheap, effective, rugged, and safe) method with a simple cleanup procedure has been developed for simultaneously determining 227 pesticides in pepper samples by liquid chromatography with tandem mass spectrometry (running time: 10 min). Pesticide residues were extracted/partitioned with an acetonitrile/DisQuE QuEChERS pouch, and the resulting samples were cleaned up with different methods: dispersive solid-phase extraction with primary secondary amines or multiwalled carbon nanotubes and graphitized carbon solid mini cartridge column. The results indicated that multiwalled carbon nanotubes dispersive sorbents achieved the best recoveries and had less matrix interference. The numbers of pesticides with a recovery in the range of 70-120% were 199 at a spiked level of 40 μg/kg. The correlation coefficients (r(2)) for 227 pesticides were above 0.99, while the limits of quantitation of pesticides in pepper samples ranged from 0.13 to 13.51 μg/kg (S/N = 10), and the limits of detection ranged from 0.04 to 4.05 μg/kg (S/N = 3). The relative standard deviations of approximately 197 pesticides were below 20% at spiked levels of 40 μg/kg. Based on these results, the proposed method was chosen as the most suitable cleanup procedure for the determination of multiresidue pesticides in pepper samples. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Four quadrant control of induction motors

NASA Technical Reports Server (NTRS)

Hansen, Irving G.

1991-01-01

Induction motors are the nation's workhorse, being the motor of choice in most applications due to their simple rugged construction. It has been estimated that 14 to 27 percent of the country's total electricity use could be saved with adjustable speed drives. Until now, induction motors have not been suited well for variable speed or servo-drives, due to the inherent complexity, size, and inefficiency of their variable speed controls. Work at NASA Lewis Research Center on field oriented control of induction motors using pulse population modulation method holds the promise for the desired drive electronics. The system allows for a variable voltage to frequency ratio which enables the user to operate the motor at maximum efficiency, while having independent control of both the speed and torque of an induction motor in all four quadrants of the speed torque map. Multiple horsepower machine drives were demonstrated, and work is on-going to develop a 20 hp average, 40 hp peak class of machine. The pulse population technique, results to date, and projections for implementation of this existing new motor control technology are discussed.

Investigation of the presence of β-hydroxy-β-methylbutyric acid and α-hydroxyisocaproic acid in bovine whole milk and fermented dairy products by a validated liquid chromatography-mass spectrometry method.

PubMed

Ehling, Stefan; Reddy, Todime M

2014-02-19

A simple, rugged, quantitative, and confirmatory method based on liquid chromatography-mass spectrometry was developed and comprehensively validated for the analysis of the leucine metabolites β-hydroxy-β-methylbutyric acid (HMB) and α-hydroxyisocaproic acid (HICA) in bovine whole milk and yogurt. Mean accuracy (90-110% for HMB and 85-115% for HICA) and total precision (<10% RSD in most cases, except for <20% RSD for HMB at the limit of quantitation) at four concentration levels across three validation runs have been determined. Limits of quantitation for HMB and HICA in whole milk were 20 and 5 μg/L, respectively. Measured concentrations of HMB and HICA were <20-29 and 32-37 μg/L, respectively, in bovine whole milk and <5 and 3.0-15.2 mg/L, respectively, in yogurt. These concentrations are insufficient by large margins to deliver any musculoskeletal benefits, and fortification of milk and dairy products with HMB and/or HICA appears to be justified.

Relaxation processes in a low-order three-dimensional magnetohydrodynamics model

NASA Technical Reports Server (NTRS)

Stribling, Troy; Matthaeus, William H.

1991-01-01

The time asymptotic behavior of a Galerkin model of 3D magnetohydrodynamics (MHD) has been interpreted using the selective decay and dynamic alignment relaxation theories. A large number of simulations has been performed that scan a parameter space defined by the rugged ideal invariants, including energy, cross helicity, and magnetic helicity. It is concluded that time asymptotic state can be interpreted as a relaxation to minimum energy. A simple decay model, based on absolute equilibrium theory, is found to predict a mapping of initial onto time asymptotic states, and to accurately describe the long time behavior of the runs when magnetic helicity is present. Attention is also given to two processes, operating on time scales shorter than selective decay and dynamic alignment, in which the ratio of kinetic to magnetic energy relaxes to values 0(1). The faster of the two processes takes states initially dominant in magnetic energy to a state of near-equipartition between kinetic and magnetic energy through power law growth of kinetic energy. The other process takes states initially dominant in kinetic energy to the near-equipartitioned state through exponential growth of magnetic energy.

The microassay on a card: A rugged, portable immunoassay

NASA Technical Reports Server (NTRS)

Kidwell, David

1991-01-01

The Microassay on a Card (MAC) is a portable, hand-held, non-instrumental immunoassay that can test for the presence of a wide variety of substances in the environment. The MAC is a simple device to use. A drop of test solution is placed on one side of the card and within five minutes a color is developed on the other side in proportion to the amount of substance in the test solution, with sensitivity approaching 10 ng/ml. The MAC is self-contained and self-timed; no reagents or timing is necessary. The MAC may be configured with multiple wells to provide simultaneous testing for multiple species. As envisioned, the MAC will be employed first as an on-site screen for drugs of abuse in urine or saliva. If the MAC can be used as a screen of saliva for drugs of abuse, it could be applied to driving while intoxicated, use of drugs on the job, or testing of the identity of seized materials. With appropriate modifications, the MAC also could be used to test for environmental toxins or pollutants.

Hue discrimination in Iberoamerican Observers

NASA Astrophysics Data System (ADS)

Carranza, Jazmín; Medina, Juana

2008-04-01

In this work we analyze the Farnsworth Munsell 100 Hue Test results, this test offers a simple method for testing color discrimination and was applied to a sample of 129 observers, with natural daylight in the same conditions (the observers were men and women), all of these were participants in colorimetric training courses, and aged 20 to 76, with two to twenty five years experience in the color control manufacturer laboratories (of plastics, rugs, dyes, textiles, and paints). Their job titles included mixers, inspectors, shaders, matchers, passers, and dyers. The test was applied twice and the results here presented are the comparison between both tests, taking into account errors by mistakes incidence in each hue position, as well as the redeeming of each participant in both test. The comparison shows us that most of the mistakes are in the green hue in both tests, but in the second test, approximately 20 percent of the observers reduced those. Also we can to separate persons with normal color vision of those which have zones of color confusion. In this work it is show some ones results of the comparison between men and women.

QuEChERS Purification Combined with Ultrahigh-Performance Liquid Chromatography Tandem Mass Spectrometry for Simultaneous Quantification of 25 Mycotoxins in Cereals

PubMed Central

Sun, Juan; Li, Weixi; Zhang, Yan; Hu, Xuexu; Wu, Li; Wang, Bujun

2016-01-01

A method based on the QuEChERS (quick, easy, cheap, effective, rugged, and safe) purification combined with ultrahigh performance liquid chromatography tandem mass spectrometry (UPLC–MS/MS), was optimized for the simultaneous quantification of 25 mycotoxins in cereals. Samples were extracted with a solution containing 80% acetonitrile and 0.1% formic acid, and purified with QuEChERS before being separated by a C18 column. The mass spectrometry was conducted by using positive electrospray ionization (ESI+) and multiple reaction monitoring (MRM) models. The method gave good linear relations with regression coefficients ranging from 0.9950 to 0.9999. The detection limits ranged from 0.03 to 15.0 µg·kg−1, and the average recovery at three different concentrations ranged from 60.2% to 115.8%, with relative standard deviations (RSD%) varying from 0.7% to 19.6% for the 25 mycotoxins. The method is simple, rapid, accurate, and an improvement compared with the existing methods published so far. PMID:27983693

Validation of QuEChERS based method for determination of fenitrothion residues in tomatoes by gas chromatography-flame photometric detector: Decline pattern and risk assessment.

PubMed

Malhat, Farag; Boulangé, Julien; Abdelraheem, Ehab; Abd Allah, Osama; Abd El-Hamid, Rania; Abd El-Salam, Shokr

2017-08-15

A simple and rapid gas chromatography with flame photometric detector (GC-FPD) determination method was developed to detect residue levels and investigate the dissipation pattern and safe use of fenitrothion in tomatoes. A modified quick, easy, cheap, effective, rugged, and safe (QuEChERS) using an ethyl acetate-based extraction, followed by a dispersive solid-phase extraction (d-SPE) with primary-secondary amine (PSA) and graphite carbon black (GCB) for clean up, was applied prior to GC-FPD analysis. The method showed satisfactory linearity, recovery and precision. The limits of detection (LOD) and quantification (LOQ) were 0.005 and 0.01mg/kg, respectively. The residue levels of fenitrothion were best described by first order kinetics with a half-life of 2.2days in tomatoes. The potential health risks posed by fenitrothion were not significant, based on supervised residue trial data. The current findings could provide guidance for safe and reasonable use of fenitrothion in tomatoes and prevent health problems to consumers. Copyright © 2017 Elsevier Ltd. All rights reserved.

Development of quadruped walking locomotion gait generator using a hybrid method

NASA Astrophysics Data System (ADS)

Jasni, F.; Shafie, A. A.

2013-12-01

The earth, in many areas is hardly reachable by the wheeled or tracked locomotion system. Thus, walking locomotion system is becoming a favourite option for mobile robot these days. This is because of the ability of walking locomotion to move on the rugged and unlevel terrains. However, to develop a walking locomotion gait for a robot is not a simple task. Central Pattern Generator (CPGs) method is a biological inspired method that is introduced as a method to develop the gait for the walking robot recently to tackle the issue faced by the conventional method of pre-designed trajectory based method. However, research shows that even the CPG method do have some limitations. Thus, in this paper, a hybrid method that combines CPG and the pre-designed trajectory based method is introduced to develop a walking gait for quadruped walking robot. The 3-D foot trajectories and the joint angle trajectories developed using the proposed method are compared with the data obtained via the conventional method of pre-designed trajectory to confirm the performance.

Household Hazardous Waste

MedlinePlus

... wipe furniture. Rug Deodorizer Liberally sprinkle carpets with baking soda. Wait at least 15 minutes and vacuum. ... with one teaspoon of salt, one teaspoon of baking soda and a sheet of aluminum foil. Totally ...

Development and Validation of a Precise, Single HPLC Method for the Determination of Tolperisone Impurities in API and Pharmaceutical Dosage Forms.

PubMed

Raju, Thummala Veera Raghava; Seshadri, Raja Kumar; Arutla, Srinivas; Mohan, Tharlapu Satya Sankarsana Jagan; Rao, Ivaturi Mrutyunjaya; Nittala, Someswara Rao

2013-01-01

A novel, sensitive, stability-indicating HPLC method has been developed for the quantitative estimation of Tolperisone-related impurities in both bulk drugs and pharmaceutical dosage forms. Effective chromatographic separation was achieved on a C18 stationary phase with a simple mobile phase combination delivered in a simple gradient programme, and quantitation was by ultraviolet detection at 254 nm. The mobile phase consisted of a buffer and acetonitrile delivered at a flow rate 1.0 ml/min. The buffer consisted of 0.01 M potassium dihydrogen phosphate with the pH adjusted to 8.0 by using diethylamine. In the developed HPLC method, the resolution between Tolperisone and its four potential impurities was found to be greater than 2.0. Regression analysis showed an R value (correlation coefficient) of greater than 0.999 for the Tolperisone impurities. This method was capable of detecting all four impurities of Tolperisone at a level of 0.19 μg/mL with respect to the test concentration of 1000 μg/mL for a 10 µl injection volume. The tablets were subjected to the stress conditions of hydrolysis, oxidation, photolysis, and thermal degradation. Considerable degradation was found to occur in base hydrolysis, water hydrolysis, and oxidation. The stress samples were assayed against a qualified reference standard and the mass balance was found to be close to 100%. The established method was validated and found to be linear, accurate, precise, specific, robust, and rugged.

Determination of phthalate esters in soil using a quick, easy, cheap, effective, rugged, and safe method followed by GC-MS.

PubMed

Liu, Qianjun; Chen, Di; Wu, Jiyuan; Yin, Guangcai; Lin, Qintie; Zhang, Min; Hu, Huawen

2018-04-01

A quick, easy, cheap, effective, rugged, and safe procedure was designed to extract pesticide residues from fruits and vegetables with a high percentage of water. It has not been used extensively for the extraction of phthalate esters from sediments, soils, and sludges. In this work, this procedure was combined with gas chromatography with mass spectrometry to determine 16 selected phthalate esters in soil. The extraction efficiency of the samples was improved by ultrasonic extraction and dissolution of the soil samples in ultra-pure water, which promoted the dispersion of the samples. Furthermore, we have simplified the extraction step and reduced the risk of organic solvent contamination by minimizing the use of organic solvents. Different extraction solvents and clean-up adsorbents were compared to optimize the procedure. Dichloromethane/n-hexane (1:1, v/v) and n-hexane/acetone (1:1, v/v) were selected as the extractants from the six extraction solvents tested. C18/primary secondary amine (1:1, m/m) was selected as the sorbent from the five clean-up adsorbents tested. The recoveries from the spiked soils ranged from 70.00 to 117.90% with relative standard deviation values of 0.67-4.62%. The proposed approach was satisfactorily applied for the determination of phthalate esters in 12 contaminated soil samples. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Compact liquid crystal waveguide Fourier transform spectrometer for real-time gas sensing in NIR spectral band

NASA Astrophysics Data System (ADS)

Chao, Tien-Hsin; Lu, Thomas T.; Davis, Scott R.; Rommel, Scott D.; Farca, George; Luey, Ben; Martin, Alan; Anderson, Michael H.

2012-04-01

Jet Propulsion Lab and Vescent Photonics Inc. and are jointly developing an innovative ultra-compact (volume < 10 cm3), ultra-low power (<10 -3 Watt-hours per measurement and zero power consumption when not measuring), completely non-mechanical Liquid Crystal Waveguide Fourier Transform Spectrometer (LCWFTS) that will be suitable for a variety of remote-platform, in-situ measurements. These devices are made possible by novel electro-evanescent waveguide architecture, enabling "monolithic chip-scale" Electro Optic-FTS (EO-FTS) sensors. The potential performance of these EO-FTS sensors include: i) a spectral range throughout 0.4-5 μm (25000 - 2000 cm-1), ii) highresolution (Δλ<= 0.1 nm), iii) high-speed (< 1 ms) measurements, and iv) rugged integrated optical construction. This performance potential enables the detection and quantification of a large number of different atmospheric gases simultaneously in the same air mass and the rugged construction will enable deployment on previously inaccessible platforms. The sensor construction is also amenable for analyzing aqueous samples on remote floating or submerged platforms. We have reported [1] a proof-of-principle prototype LCWFTS sensor that has been demonstrated in the near- IR (range of 1450-1600 nm) with a 5 nm resolution. In this paper, we will report the recently built and tested LCWFTS test bed and the demonstration of a real-time gas sensing applications.

New analytical method for the determination of musks in personal care products by Quick, Easy, Cheap, Effective, Rugged, and Safe extraction followed by GC-MS.

PubMed

Homem, Vera; Silva, José Avelino; Cunha, Carina; Alves, Arminda; Santos, Lúcia

2013-07-01

Synthetic musks are organic compounds used as fragrance additives and fixative compounds in a diversity of personal care products. A new method based on quick, easy, cheap, effective, rugged, and safe (QuEChERS) extraction followed by GC-MS for the analysis of 12 musks in personal care products was developed and validated. Some experimental parameters, such as total QuEChERS mass, sample mass/solvent volume ratio, type of extraction solvent, as well as salts and sorbents amount were investigated and optimized. The final method involves the musks extraction using acetonitrile, followed by the addition of anhydrous magnesium sulphate and sodium acetate. The clean-up step was performed using dispersive SPE with primary and secondary amine and octadecyl-silica sorbents. This extraction procedure is fast (about 10 min) when compared to other traditional approaches. The method was robust for the matrices studied and shows a high precision (%RSD < 15%) and accuracy (average recovery of 85%), allowing the detection of musks in minimum concentrations between 0.01 ng/g (galaxolide) and 15.80 ng/g (musk xylene). The developed method was applied to the analysis of 12 samples, which revealed musks concentrations ranging from 2 ng/g (toothpaste) to 882,340 ng/g (perfumed body lotion). © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

High speed radiometric measurements of IED detonation fireballs

NASA Astrophysics Data System (ADS)

Spidell, Matthew T.; Gordon, J. Motos; Pitz, Jeremey; Gross, Kevin C.; Perram, Glen P.

2010-04-01

Continuum emission is predominant in fireball spectral phenomena and in some demonstrated cases, fine detail in the temporal evolution of infrared spectral emissions can be used to estimate size and chemical composition of the device. Recent work indicates that a few narrow radiometric bands may reveal forensic information needed for the explosive discrimination and classification problem, representing an essential step in moving from "laboratory" measurements to a rugged, fieldable system. To explore phenomena not observable in previous experiments, a high speed (10μs resolution) radiometer with four channels spanning the infrared spectrum observed the detonation of nine home made explosive (HME) devices in the < 100lb class. Radiometric measurements indicate that the detonation fireball is well approximated as a single temperature blackbody at early time (0 < t <~ 3ms). The effective radius obtained from absolute intensity indicates fireball growth at supersonic velocity during this time. Peak fireball temperatures during this initial detonation range between 3000.3500K. The initial temperature decay with time (t <~ 10ms) can be described by a simple phenomenological model based on radiative cooling. After this rapid decay, temperature exhibits a small, steady increase with time (10 <~ t <~ 50ms) and peaking somewhere between 1000.1500K-likely the result of post-detonation combustion-before subsequent cooling back to ambient conditions . Radius derived from radiometric measurements can be described well (R2 > 0.98) using blast model functional forms, suggesting that energy release could be estimated from single-pixel radiometric detectors. Comparison of radiometer-derived fireball size with FLIR infrared imagery indicate the Planckian intensity size estimates are about a factor of two smaller than the physical extent of the fireball.

Rover imaging system for the Mars rover/sample return mission

NASA Technical Reports Server (NTRS)

1993-01-01

In the past year, the conceptual design of a panoramic imager for the Mars Environmental Survey (MESUR) Pathfinder was finished. A prototype camera was built and its performace in the laboratory was tested. The performance of this camera was excellent. Based on this work, we have recently proposed a small, lightweight, rugged, and highly capable Mars Surface Imager (MSI) instrument for the MESUR Pathfinder mission. A key aspect of our approach to optimization of the MSI design is that we treat image gathering, coding, and restoration as a whole, rather than as separate and independent tasks. Our approach leads to higher image quality, especially in the representation of fine detail with good contrast and clarity, without increasing either the complexity of the camera or the amount of data transmission. We have made significant progress over the past year in both the overall MSI system design and in the detailed design of the MSI optics. We have taken a simple panoramic camera and have upgraded it substantially to become a prototype of the MSI flight instrument. The most recent version of the camera utilizes miniature wide-angle optics that image directly onto a 3-color, 2096-element CCD line array. There are several data-taking modes, providing resolution as high as 0.3 mrad/pixel. Analysis tasks that were performed or that are underway with the test data from the prototype camera include the following: construction of 3-D models of imaged scenes from stereo data, first for controlled scenes and later for field scenes; and checks on geometric fidelity, including alignment errors, mast vibration, and oscillation in the drive system. We have outlined a number of tasks planned for Fiscal Year '93 in order to prepare us for submission of a flight instrument proposal for MESUR Pathfinder.

Performance of a 2.5 THz Receiver Front-End for Spaceborne Applications

NASA Technical Reports Server (NTRS)

Gaidis, Michael C.; Pickett, H. M.; Siegel, P. H.; Smith, C. D.; Smith, R. P.; Martin, S. C.

1999-01-01

The OH radical plays a significant role in a great many of the known ozone destruction cycles, and has become the focus of an important radiometer development effort for NASA's Earth Observing System Chem I satellite, which will monitor and study many tropospheric and stratospheric gases and is scheduled for launch in 2002. Here we describe the design, fabrication, and testing of a receiver front end used to detect the OH signals at 2.5 THz. This is to be the first Terahertz heterodyne receiver to be flown in space. The challenges of producing the necessary high-performance mixers are numerous, but for this application, there is the added challenge of designing a robust receiver which can withstand the environmental extremes of a rocket launch and five years in space. The receiver front-end consists of the following components: a four-port dual-polarization diplexer, off-axis elliptical feed mirrors, mixers for horizontal and vertical polarization, support structures allowing simple and rugged alignment, low noise IF amplification from 7.7 to 21.1 GHz, and mixer DC bias circuitry. The front-end design, alignment, and operation will be covered in depth, followed by a discussion of the most recent results in receiver noise and dual-mode horn beam patterns. JPL MOMED mixers are employed, and have resulted in receiver noise temperatures of 14,500 K, DSB with LO frequency 2.522 GHz and IF of 12.8 GHz. Horn beam patterns correspond well with theory, with no significant sidelobes above the -25 dB level. Considering the high-quality beam of this receiver, these results are competitive with the best reported in the literature.

HIGH SENSITIVITY ELECTROSCOPE

DOEpatents

Shonka, F.R.; Okleshen, A.J.

1958-08-12

An electrometer with dependable and rugged construction for measuring cxtremely small charges is de scribed. The electrometer arrangement comprises an electrically conducting fiber totally disposed in a single plane in the absence of electrosthtic forces and affixed at both ends to fiber support means. The fiber is provided with a plurality of adjacent bends in opposite directions along its length..An electrode is disposed between two adjacent bends to apply an electrostatic force normal to the plane of the fiber whereby the fiber is caused to twist out of its plane in proportion to the potential apptied between the fiber and the electrode.

Scintillator assembly for alpha radiation detection and an associated method of making

DOEpatents

Lauf, R.J.; McElhaney, S.A.; Bates, J.B.

1994-07-26

A scintillator assembly for use in conjunction with a photomultiplier or the like in the detection of alpha radiation utilizes a substrate or transparent yttrium aluminum garnet and a relatively thin film of cerium-doped yttrium aluminum garnet coated upon the substrate. The film material is applied to the substrate in a sputtering process, and the applied film and substrate are annealed to effect crystallization of the film upon the substrate. The resultant assembly provides relatively high energy resolution during use in a detection instrument and is sufficiently rugged for use in field environments. 4 figs.

Scintillator assembly for alpha radiation detection and an associated method of making

DOEpatents

Lauf, Robert J.; McElhaney, Stephanie A.; Bates, John B.

1994-01-01

A scintillator assembly for use in conjunction with a photomultiplier or the like in the detection of alpha radiation utilizes a substrate or transparent yttrium aluminum garnet and a relatively thin film of cerium-doped yttrium aluminum garnet coated upon the substrate. The film material is applied to the substrate in a sputtering process, and the applied film and substrate are annealed to effect crystallization of the film upon the substrate. The resultant assembly provides relatively high energy resolution during use in a detection instrument and is sufficiently rugged for use in field environments.

Use of Hardware Battery Drill in Orthopedic Surgery.

PubMed

Satish, Bhava R J; Shahdi, Masood; Ramarao, Duddupudi; Ranganadham, Atmakuri V; Kalamegam, Sundaresan

2017-03-01

Among the power drills (Electrical/Pneumatic/Battery) used in Orthopedic surgery, battery drill has got several advantages. Surgeons in low resource settings could not routinely use Orthopedic battery drills (OBD) due to the prohibitive cost of good drills or poor quality of other drills. "Hardware" or Engineering battery drill (HBD) is a viable alternative to OBD. HBD is easy to procure, rugged in nature, easy to maintain, durable, easily serviceable and 70 to 75 times cheaper than the standard high end OBD. We consider HBD as one of the cost effective equipment in Orthopedic operation theatres.

Design of a ZVS PWM inverter for a brushless DC motor in an EMA application

NASA Technical Reports Server (NTRS)

Bell, J. Brett; Nelms, R. M.; Shepherd, Michael T.

1993-01-01

The Component Development Division of the Propulsion Laboratory at Marshall Space Flight Center (MSFC) is currently investigating the use of electromechanical actuators for use in space transportation applications such as Thrust Vector Control (TVC). These high power servomechanisms will require rugged, reliable, and compact power electronic modules capable of modulating several hundred amperes of current at up to 270 Vdc. This paper will discuss the design and implementation of a zero-voltage-switched PWM (Pulse Width Modulation) inverter which operates from a 270 Vdc source at currents up to 100 A.

16 CFR 1631.1 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-01-01

... to be walked upon. (f) Timed Burning Tablet (pill) means a methenamine tablet, flat, with a nominal...) Fire-Retardant Treatment means any process to which a small carpet or rug has been exposed which...

Inexpensive cryogenic insulation replaces vacuum jacketed line

NASA Technical Reports Server (NTRS)

Fuchs, C. E.

1967-01-01

Commercially available aluminized Mylar, cork and fiber glass form a multilayered sealed system and provide rugged and economical field installed insulation for cryogenic /liquid nitrogen or oxygen/ pipe lines in an exposed environment.

New Zealand Southern Alps

NASA Image and Video Library

2001-06-20

This anaglyph from the MISR instrument aboard NASA Terra spacecraft shows the rugged Southern Alps extending some 650 kilometers along the western side of New Zealand South Island. 3D glasses are necessary to view this image.

Remote sensing applications to hydrologic modeling

NASA Technical Reports Server (NTRS)

Dozier, J.; Estes, J. E.; Simonett, D. S.; Davis, R.; Frew, J.; Marks, D.; Schiffman, K.; Souza, M.; Witebsky, E.

1977-01-01

An energy balance snowmelt model for rugged terrain was devised and coupled to a flow model. A literature review of remote sensing applications to hydrologic modeling was included along with a software development outline.

Temperature Control of Avalanche Photodiode Using Thermoelectric Cooler

NASA Technical Reports Server (NTRS)

Refaat, Tamer F.; Luck, William S., Jr.; DeYoung, Russell J.

1999-01-01

Avalanche photodiodes (APDS) are quantum optical detectors that are used for visible and near infrared optical detection applications. Although APDs are compact, rugged, and have an internal gain mechanism that is suitable for low light intensity; their responsivity, and therefore their output, is strongly dependent on the device temperature. Thermoelectric coolers (TEC) offers a suitable solution to this problem. A TEC is a solid state cooling device, which can be controlled by changing its current. TECs are compact and rugged, and they can precisely control the temperature to within 0.1 C with more than a 150 C temperature gradient between its surfaces. In this Memorandum, a proportional integral (PI) temperature controller for APDs using a TEC is discussed. The controller is compact and can successfully cool the APD to almost 0 C in an ambient temperature environment of up to 27 C.

Magnetic-field sensing coil embedded in ceramic for measuring ambient magnetic field

DOEpatents

Takahashi, Hironori

2004-02-10

A magnetic pick-up coil for measuring magnetic field with high specific sensitivity, optionally with an electrostatic shield (24), having coupling elements (22) with high winding packing ratio, oriented in multiple directions, and embedded in ceramic material for structural support and electrical insulation. Elements of the coil are constructed from green ceramic sheets (200) and metallic ink deposited on surfaces and in via holes of the ceramic sheets. The ceramic sheets and the metallic ink are co-fired to create a monolithic hard ceramic body (20) with metallized traces embedded in, and placed on exterior surfaces of, the hard ceramic body. The compact and rugged coil can be used in a variety of environments, including hostile conditions involving ultra-high vacuum, high temperatures, nuclear and optical radiation, chemical reactions, and physically demanding surroundings, occurring either individually or in combinations.

High-throughput infrared spectrometer for standoff chemical detection

NASA Astrophysics Data System (ADS)

Chadha, Suneet; Stevenson, Chuck; Curtiss, Lawrence E.

1999-01-01

Advanced autonomous detection of chemical warfare agents and other organic materials has long been a major military concern. While significant advances have recently been accomplished in remote spectral sensing using rugged FTIRs with point detectors, efforts towards spatial chemical discrimination have been lacking. Foster-Miller, Inc. has developed a radically different mid-IR and long wave IR spectrometer for standoff detection of chemical warfare agents and other molecular species.This no moving parts device will eliminate the cost, complexity, reliability and bandwidth/resolution problems associated with either Fabry Perot or Michelson Interferometer based approaches currently under consideration. Given the small size and performance insensitivity to on-board vibration, high EMI, thermal variations, the proposed optic would easily adapt cryocooling and field deployable requirements for low radiance detection.

Map showing scenic features and recreation facilities of the Salina quadrangle, Utah

USGS Publications Warehouse

Williams, Paul L.; Covington, Harry R.

1973-01-01

This map is intended as a guide for those who enjoy outdoor recreation in magnificent scenic settings.The Salina quadrangle lies in the heart of the Colorado Plateau, a sparsely populated land of unique and outstanding scenic beauty. The eastern half of the quadrangle is a great desert, partly blanketed by sand dunes, but  mostly an area of badlands multicolored cliffs and benches of virtually barren rock, and deeply incised canyons. In the west half of the quadrangle, rugged tree-covered foothills flank high forested plateaus rimmed by cliffs. On these High Plateaus, dense coniferous forest is interspersed with wide grassy parks, grazed in summer by sheep and cattle. Valleys between the plateaus contain irrigated crop lands.

Fundamentals of electric power conversion. Volume 2, Energy-efficient polyphase AC induction motors, final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Umans, S.D.

1992-12-01

Its rugged nature and straightforward design make the induction motor the most commonly used type of electric motor. This motor ranges in size fro the fractional-horsepower, single-phase motors found in household appliances to polyphase motors rated at thousands of horsepower for industrial applications. Volume 1 of this report describes the function of induction motors, their characteristics, and induction motor testing. Volume 2 describes the characteristics of high-efficiency induction motors, with emphasis on the techniques used to obtain high efficiency. This two-volume report is written in nontechnical language and is intended for readers who require background from applications, marketing, motor planning,more » or managerial perspective.« less

Fundamentals of electric power conversion. Volume 1, Operating characteristics and testing of AC induction motors, final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Umans, S.D.

1992-12-01

Its rugged nature and straightforward design make the induction motor the most commonly used type of electric motor. This motor ranges in size from the fractional-horsepower, single-phase motors found in household appliances to polyphase motors rated at thousands of horsepower for industrial applications. Volume 1 of this report describes the function of induction motors, their characteristics, and induction motor testing. Volume 2 describes the characteristics of high-efficiency induction motors, with emphasis on the techniques used to obtain high efficiency. This two-volume report is written in nontechnical language and is intended for readers who require background from an applications, marketing, motormore » planning, or managerial perspective.« less

The LEBIT ion cooler and buncher

NASA Astrophysics Data System (ADS)

Schwarz, S.; Bollen, G.; Ringle, R.; Savory, J.; Schury, P.

2016-04-01

This paper presents a detailed description of the ion cooler and buncher, installed at the Low Energy Beam and Ion Trap Facility (LEBIT) at the National Superconducting Cyclotron Laboratory (NSCL). NSCL uses gas stopping to provide rare isotopes from projectile fragmentation for its low-energy physics program and to the re-accelerator ReA. The LEBIT ion buncher converts the continuous rare-isotope beam, delivered from the gas stopping cell, into short, low-emittance ion pulses, required for high-precision mass measurements with a 9.4 T Penning trap mass spectrometer. Operation at cryogenic temperatures, a simplified electrode structure and dedicated rugged electronics contribute to the high performance and reliability of the device, which have been essential to the successful LEBIT physics program since 2005.

Mesoscale simulations of atmospheric flow and tracer transport in Phoenix, Arizona

NASA Astrophysics Data System (ADS)

Wang, Ge; Ostoja-Starzewski, Martin

2006-09-01

Large urban centres located within confining rugged or complex terrain can frequently experience episodes of high concentrations of lower atmospheric pollution. Metropolitan Phoenix, Arizona (United States), is a good example, as the general population is occasionally subjected to high levels of lower atmospheric ozone, carbon monoxide and suspended particulate matter. As a result of dramatic but continuous increase in population, the accompanying environmental stresses and the local atmospheric circulation that dominates the background flow, an accurate simulation of the mesoscale pollutant transport across Phoenix and similar urban areas is becoming increasingly important. This is particularly the case in an airshed, such as that of Phoenix, where the local atmospheric circulation is complicated by the complex terrain of the area.

Design and development of an advanced two-stage centrifugal compressor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Palmer, D.L.; Waterman, W.F.

1995-04-01

Small turboshaft engines require high-pressure-ratio, high-efficiency compressors to provide low engine fuel consumption. This paper describes the aeromechanical design and development of a 3.3 kg/s (7.3 lb/sec), 14:1 pressure ratio two-stage centrifugal compressor, which is used in the T800-LHT-800 helicopter engine. The design employs highly nonradial, splitter bladed impellers with swept leading edges and compact vaned diffusers to achieve high performance in a small and robust configuration. The development effort quantified the effects of impeller diffusion and passive inducer shroud bleed on surge margin as well as the effects of impeller loading on tip clearance sensitivity and the impact ofmore » sand erosion and shroud roughness on performance. The developed compressor exceeded its performance objectives with a minimum of 23% surge margin without variable geometry. The compressor provides a high-performance, rugged, low-cost configuration ideally suited for helicopter applications.« less

MESSENGER Reveals Mercury in New Detail

NASA Image and Video Library

2008-01-16

As NASA MESSENGER approached Mercury on January 14, 2008, the spacecraft Narrow-Angle Camera on the Mercury Dual Imaging System MDIS instrument captured this view of the planet rugged, cratered landscape illuminated obliquely by the Sun.

Bugs in Your Rugs? Carpet Maintenance and Indoor Air Quality.

ERIC Educational Resources Information Center

Schmidt, Edward A.

1994-01-01

This article, the second in a three-part series of articles that discuss indoor air quality (IAQ) issues affecting schools, looks at the effects of carpet maintenance and environmental influences on IAQ. (MLF)

Fireman's lamp

NASA Technical Reports Server (NTRS)

Britz, W. J.; Varnedoe, W. W., Jr.

1977-01-01

Rugged lamp used by miners is adapted for firefighters by utilization of smaller, rechargeable 3-hour-life gel-cell battery. Lighter, maintenance free unit can be clipped to outer clothing for convenience. Small monitor circuit indicates need to recharge battery.

Hospital to Home: Plan for a Smooth Transition

MedlinePlus

... can cause falls, such as area rugs and electric cords (a good idea in any event) ■ Create ... on many aspects of transitions, including medication management, discharge checklists, hospice and palliative care, and many others. ...

Multiresidue determination of pesticides in crop plants by the quick, easy, cheap, effective, rugged, and safe method and ultra-high-performance liquid chromatography tandem mass spectrometry using a calibration based on a single level standard addition in the sample.

PubMed

Viera, Mariela S; Rizzetti, Tiele M; de Souza, Maiara P; Martins, Manoel L; Prestes, Osmar D; Adaime, Martha B; Zanella, Renato

2017-12-01

In this study, a QuEChERS (Quick, Easy, Cheap, Effective, Rugged and Safe) method, optimized by a 2 3 full factorial design, was developed for the determination of 72 pesticides in plant parts of carrot, corn, melon, rice, soy, silage, tobacco, cassava, lettuce and wheat by ultra-high-performance liquid chromatographic tandem mass spectrometry (UHPLC-MS/MS). Considering the complexity of these matrices and the need of use calibration in matrix, a new calibration approach based on single level standard addition in the sample (SLSAS) was proposed in this work and compared with the matrix-matched calibration (MMC), the procedural standard calibration (PSC) and the diluted standard addition calibration (DSAC). All approaches presented satisfactory validation parameters with recoveries from 70 to 120% and relative standard deviations≤20%. SLSAS was the most practical from the evaluated approaches and proved to be an effective way of calibration. Method limit of detection were between 4.8 and 48μgkg -1 and limit of quantification were from 16 to 160μgkg -1 . Method application to different kinds of plants found residues of 20 pesticides that were quantified with z-scores values≤2 in comparison with other calibration approaches. The proposed QuEChERS method combined with UHPLC-MS/MS analysis and using an easy and effective calibration procedure presented satisfactory results for pesticide residues determination in different crop plants and is a good alternative for routine analysis. Copyright © 2017 Elsevier B.V. All rights reserved.

Reminder of Ages Past

NASA Image and Video Library

2006-05-26

Rhea displays a prominent scar in this view from Cassini. A large and ancient impact basin can be seen at upper right. The giant feature occurs within a terrain that appears rugged and which likely is saturated with other smaller craters

An Integrated-Circuit Temperature Sensor for Calorimetry and Differential Temperature Measurement.

ERIC Educational Resources Information Center

Muyskens, Mark A.

1997-01-01

Describes the application of an integrated-circuit (IC) chip which provides an easy-to-use, inexpensive, rugged, computer-interfaceable temperature sensor for calorimetry and differential temperature measurement. Discusses its design and advantages. (JRH)

3 CFR 9024 - Proclamation 9024 of September 26, 2013. National Public Lands Day, 2013

Code of Federal Regulations, 2014 CFR

2014-01-01

... diverse and rugged landscapes reflect our national character, the way we care for these open spaces.... Since I established this initiative, we have expanded access to recreation, restored critical landscapes...

Vectorcardiogram

NASA Technical Reports Server (NTRS)

Costello, M.

1973-01-01

System measures electrocardiographic potentials to produce precise quantitative measurement of changes that occur in individual's cardiac function. System is rugged, built to sustain extremes of temperature, pressure, humidity, shock, and vibration. It can also be used in pure oxygen environment without danger of combustion.

Terrain Perception for DEMO III

NASA Technical Reports Server (NTRS)

Manduchi, R.; Bellutta, P.; Matthies, L.; Owens, K.; Rankin, A.

2000-01-01

The Demo III program has as its primary focus the development of autonomous mobility for a small rugged cross country vehicle. In this paper we report recent progress on both stereo-based obstacle detection and terrain cover color-based classification.

Dawn LAMO Image 89

NASA Image and Video Library

2016-05-16

This image captured by NASA Dawn spacecraft features the shadowy rim of an unnamed crater on Ceres. The crater on the left appears relatively old, as its flanks are rugged and the crater density inside it is more or less uniform.

1st Order Modeling of a SAW Delay Line using MathCAD(Registered)

NASA Technical Reports Server (NTRS)

Wilson, William C.; Atkinson, Gary M.

2007-01-01

To aid in the development of SAW sensors for Integrated Vehicle Health Monitoring applications, a first order model of a SAW Delay line has been created using MathCadA. The model implements the Impulse Response method to calculate the frequency response, impedance, and insertion loss. This paper presents the model and the results from the model for a SAW delay line design. Integrated Vehicle Health Monitoring (IVHM) of aerospace vehicles requires rugged sensors having reduced volume, mass, and power that can be used to measure a variety of phenomena. Wireless systems are preferred when retro-fitting sensors onto existing vehicles [1]. Surface Acoustic Wave (SAW) devices are capable of sensing: temperature, pressure, strain, chemical species, mass loading, acceleration, and shear stress. SAW technology is low cost, rugged, lightweight, and extremely low power. Passive wireless sensors have been developed using SAW technology. For these reasons new SAW sensors are being investigated for aerospace applications.

Rugged and breathable forms of stretchable electronics with adherent composite substrates for transcutaneous monitoring.

PubMed

Jang, Kyung-In; Han, Sang Youn; Xu, Sheng; Mathewson, Kyle E; Zhang, Yihui; Jeong, Jae-Woong; Kim, Gwang-Tae; Webb, R Chad; Lee, Jung Woo; Dawidczyk, Thomas J; Kim, Rak Hwan; Song, Young Min; Yeo, Woon-Hong; Kim, Stanley; Cheng, Huanyu; Rhee, Sang Il; Chung, Jeahoon; Kim, Byunggik; Chung, Ha Uk; Lee, Dongjun; Yang, Yiyuan; Cho, Moongee; Gaspar, John G; Carbonari, Ronald; Fabiani, Monica; Gratton, Gabriele; Huang, Yonggang; Rogers, John A

2014-09-03

Research in stretchable electronics involves fundamental scientific topics relevant to applications with importance in human healthcare. Despite significant progress in active components, routes to mechanically robust construction are lacking. Here, we introduce materials and composite designs for thin, breathable, soft electronics that can adhere strongly to the skin, with the ability to be applied and removed hundreds of times without damaging the devices or the skin, even in regions with substantial topography and coverage of hair. The approach combines thin, ultralow modulus, cellular silicone materials with elastic, strain-limiting fabrics, to yield a compliant but rugged platform for stretchable electronics. Theoretical and experimental studies highlight the mechanics of adhesion and elastic deformation. Demonstrations include cutaneous optical, electrical and radio frequency sensors for measuring hydration state, electrophysiological activity, pulse and cerebral oximetry. Multipoint monitoring of a subject in an advanced driving simulator provides a practical example.

Dust Mantle Near Pavonis Mons

NASA Technical Reports Server (NTRS)

2003-01-01

MGS MOC Release No. MOC2-356, 10 May 2003

This Mars Global Surveyor (MGS) Mars Orbiter Camera (MOC) image shows a thick mantle of dust covering lava flows north of Pavonis Mons so well that the flows are no longer visible. Flows are known to occur here because of the proximity to the volcano, and such flows normally have a very rugged surface. Fine dust, however, has settled out of the atmosphere over time and obscured the flows from view. The cliff at the top of the image faces north (up), the cliff in the middle of the image faces south (down), and the rugged slope at the bottom of the image faces north (up). The dark streak at the center-left was probably caused by an avalanche of dust sometime in the past few decades. The image is located near 4.1oN, 111.3oW. Sunlight illuminates the scene from the right/lower right.

Rugged and breathable forms of stretchable electronics with adherent composite substrates for transcutaneous monitoring

NASA Astrophysics Data System (ADS)

Jang, Kyung-In; Han, Sang Youn; Xu, Sheng; Mathewson, Kyle E.; Zhang, Yihui; Jeong, Jae-Woong; Kim, Gwang-Tae; Webb, R. Chad; Lee, Jung Woo; Dawidczyk, Thomas J.; Kim, Rak Hwan; Song, Young Min; Yeo, Woon-Hong; Kim, Stanley; Cheng, Huanyu; Rhee, Sang Il; Chung, Jeahoon; Kim, Byunggik; Chung, Ha Uk; Lee, Dongjun; Yang, Yiyuan; Cho, Moongee; Gaspar, John G.; Carbonari, Ronald; Fabiani, Monica; Gratton, Gabriele; Huang, Yonggang; Rogers, John A.

2014-09-01

Research in stretchable electronics involves fundamental scientific topics relevant to applications with importance in human healthcare. Despite significant progress in active components, routes to mechanically robust construction are lacking. Here, we introduce materials and composite designs for thin, breathable, soft electronics that can adhere strongly to the skin, with the ability to be applied and removed hundreds of times without damaging the devices or the skin, even in regions with substantial topography and coverage of hair. The approach combines thin, ultralow modulus, cellular silicone materials with elastic, strain-limiting fabrics, to yield a compliant but rugged platform for stretchable electronics. Theoretical and experimental studies highlight the mechanics of adhesion and elastic deformation. Demonstrations include cutaneous optical, electrical and radio frequency sensors for measuring hydration state, electrophysiological activity, pulse and cerebral oximetry. Multipoint monitoring of a subject in an advanced driving simulator provides a practical example.

A method for encapsulating high voltage power transformers

NASA Astrophysics Data System (ADS)

Sanchez, Robert O.

Voltage breakdowns become a major concern in reducing the size of high-voltage power converter transformers. Even the smallest of voids can provide a path for corona discharge which can cause a dielectric breakdown leading to a transformer failure. A method of encapsulating small high voltage transformers has been developed. The method virtually eliminates voids in the impregnation material, provides an exceptional dielectric between windings and provides a mechanically rugged package. The encapsulation material is a carboxyl terminated butadiene nitril (CTBN) modified mica filled epoxy. The method requires heat/vacuum to impregnate the coil and heat/pressure to cure the encapsulant. The transformer package utilizes a diallyl phthalate (DAP) contact assembly in which a coated core/coil assembly is mounted and soldered. This assembly is then loaded into an RTV mold and the encapsulation process begins.

Interaction between active tectonics, erosion and diapirism, a case study from Habble-Rud in Southern Central Alborz (Northern Iran)

NASA Astrophysics Data System (ADS)

Jaberi, Maryam; Ghassemi, Mohammad R.; Shayan, Siavosh; Yamani, Mojtaba; Zamanzadeh, Seyed Mohammad

2018-01-01

The Alborz mountain chain is a region of active deformation within the Arabia-Eurasia continental collision zone. The southern part of central Alborz Mountains, in the north of Iran, represents complex tectonics because it is located at the border of two developing continental sedimentary basins between southern central Alborz and Central Iran. An arid and semi-arid climate, a large extent of Quaternary sediments, rugged topography, salt domes and faults with historical seismicity influence the Habble-Rud River catchment. In the present research, a number of tectonic geomorphologic indices were extracted from satellite imagery and 10 m DEM (digital elevation model) data in order to identify relative tectonic activity within the basin. The indices include: stream length-gradient index (Sl), drainage basin asymmetry (Af), index of mountain front sinuosity (Smf), hypsometric integral (Hi), index of drainage basin shape (Bs), ratio of valley-floor width to valley height (Vf), and fault density (Fd). Due to the presence of heterogeneous indices for all sections of the catchment causing large extension of Habble-Rud (3260 km2), all of the variables such as extremely erodible formations, faults and folds and salt tectonics on the Southern part; were put into a matrix table. As a new approach, the variables were put into the SAW (simple additive model) model as one of MADM (multi-attribute decision-making models) techniques. The study area was divided into four regions according to the values of SAW. These classes include very high (%11), high (48.3%), moderate (34.7%), and low activity (3.4%). The result of the model suggests that the study area is located on a changing tectonic trend in central Alborz from NW-SE to NE-SW. The regions with high relative tectonic activity in HR catchment correspond to the active Garmsar and Sorkhe-Kalout faults and diapirs.

Determination of the bioavailability of selected pharmaceutical residues in fish plasma using liquid chromatography coupled to tandem mass spectrometry.

PubMed

Poirier Larabie, S; Houde, M; Gagnon, C

2017-11-03

Aquatic systems near major urban centers are constantly contaminated with effluent from wastewater treatment plants. Pharmaceuticals are part of the contamination and several classes of drugs have been detected in surface waters in the last decade. To better understand the impact of those pharmaceuticals in ecosystems, the exposure to aquatic species needs to be investigated. This study presents a new simple and rugged quantitative method for the determination of several classes of drugs using 100μL of plasma from fish environmentally exposed to a major but highly diluted urban effluent. Six common drugs (i.e., diclofenac, ibuprofen, naproxen, salbutamol, sulfamethoxazole and trimethoprim) and one major metabolite (2-hydroxy-ibuprofen), present in significant amount in impacted waterways have been selected for the development and validation of the method. First, all drugs were extracted using cation exchange solid phase extraction (SPE) and eluted with two solvent mixtures. Then, the extracts were analyzed using a reverse-phase analytical column Waters ® CORTECS C 18 + (150×2.1mm, 2.7μm) within 14min. MS/MS was performed with an electrospray (ESI) interface in positive ion mode, with multiple reaction monitoring (MRM) experiment acquiring two product ions per drugs. Quantification has been made with standard curves for each analyte using isotopically labeled internal standards. This method has high sensitivity with limits of quantification of 1ngmL -1 for each drug, except for ibuprofen and its metabolite 2-hydroxy-ibuprofen at 2ngmL -1 . The precision of the method was below 11%, the accuracy between 94 and 105% and overall recovery between 94 and 111% for all drugs, with high selectivity. Application of the method to plasma samples from wild northern pike inhabiting the St. Lawrence River collected over a three-year period showed the presence of naproxen, diclofenac, trimethoprim and salbutamol at very low concentrations (around 1ngmL -1 ). Crown Copyright © 2017. Published by Elsevier B.V. All rights reserved.

Low-loss spinel windows for high-energy lasers

NASA Astrophysics Data System (ADS)

Kim, Woohong; Baker, Colin; Villalobos, Guillermo; Bayya, Shyam; Hunt, Michael; Sadowski, Bryan; Aggarwal, Ishwar; Sanghera, Jasbinder

2014-05-01

Ideal exit aperture windows for high-energy laser (HEL) should possess low absorption and scattering losses and be environmentally rugged and strong in order to protect the laser gain medium without compromising the light propagating through the window. Spinel is an ideal candidate for this application due to its high mechanical strength, high thermal conductivity, and excellent optical transmission between 0.2~5 μm. However, spinel ceramics fabricated with commercial powders often show inhomogeneity and suffer from absorption and scattering caused by various types of intrinsic and extrinsic impurities present in the powders. Here, we report on a convenient and economical powder purification method to significantly lower the absorption loss of transparent spinel ceramics using commercial powders. Acid washing was successfully used to reduce absorption loss in spinel ceramic fabricated using commercial powder from >20,000 ppm/cm down to 75 ppm/cm.

High-Definition Optical Velocimetry: A New Diagnostic Paradigm for Nuclear Security

DOE Office of Scientific and Technical Information (OSTI.GOV)

Daykin, E; Diaz, A; Gallegos, C

This slide-show describes work done to address the challenge of high-definition optical velocimetry with hundred(s) of high-fidelity velocity vs. time measurements. After a review of the historical context and a general technical description of how optical velocimetry, particularly photonic Doppler velocimetry, works, the innovation of multiplexed photonic Doppler velocimetry (MPDV) is described as implemented with commercially available telecom products and dense wavelength division multiplexing (DWDM). High amplification of small signals allows for laser-safe operations. The authors have evaluated and leveraged telecom components– optical amplifiers, wavelength multiplexers, and seed lasers–to provide an economical, compact and rugged approach to system architecture. Fouriermore » transform data analysis is seen to be robust and capable of discriminating simultaneous data traces recorded onto a single digitizer channel. The authors successfully fielded demonstration MPDV system on shock driven experiments.« less

A quick, easy, cheap, effective, rugged, and safe method for the simultaneous detection of four triazolone herbicides in cereals combined with ultrahigh performance liquid chromatography with tandem mass spectrometry.

PubMed

Tao, Yan; Xu, Jun; Liu, Xingang; Cheng, Youpu; Liu, Na; Chen, Zenglong; Dong, Fengshou; Zheng, Yonguan

2014-09-01

This paper describes a novel, rapid, and sensitive analytical method for monitoring four triazolone herbicides in cereals (wheat, rice, corn, and soybean), using a quick, easy, cheap, effective, rugged, and safe sample extraction procedure followed by ultrahigh performance liquid chromatography coupled with tandem mass spectrometry. The four triazolone herbicides (amicarbazone, carfentrazone-ethyl, sulfentrazone, and thiencarbazone-methyl) were extracted using acidified acetonitrile (containing 1% v/v formic acid) and subsequently purified with octadecylsilane (C18 ) prior to sample analysis. Ultrahigh performance liquid chromatography coupled with tandem mass spectrometry was operated in positive and negative ionization switching mode. Amicarbazone and carfentrazone-ethyl were detected in the positive mode (ESI+), while sulfentrazone and thiencarbazone-methyl were detected in the negative mode (ESI-). All compounds were successfully separated in less than 3.0 min. Further optimization achieved desired recoveries ranging from 74.5 to 102.1% for all analytes with relative standard deviation values ≤17.2% in all tested matrices at three levels (10, 100, and 500 μg/kg). The limits of detection for all compounds were ≤2.3 μg/kg, and the limits of quantitation did not exceed 7.1 μg/kg. The developed method showed excellent linearity (R(2) ≥ 0.994) and was proven to be highly efficient and reliable for the routine monitoring of triazolone herbicides in cereals. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Low-smoke, halogenfree ship-offshore/onshore cables with improved flame retardance and fire resistance

NASA Astrophysics Data System (ADS)

Pedersen, J. R.; Holte, T. A.; Johansen, E.

Cables with improved fire resistance and flame retardance have been developed. They will continue to function at least 3 hours even at temperatures up to 1000 C and do not propagate fire when tested according to IEC 332 part 3 1982, category A. Made with halogenfree materials they give off no corrosive gases and very little visible smoke in cases of fire. Cables are made for power, signal and instrument installations in hospitals, high rise buildings, railroad cars, subways, on board ship, oil rigs and oil production platforms. The offshore cables are specially constructed to withstand the rugged climatic conditions in the North Sea area.

Near-space flight of a correlated photon system

PubMed Central

Tang, Zhongkan; Chandrasekara, Rakhitha; Sean, Yau Yong; Cheng, Cliff; Wildfeuer, Christoph; Ling, Alexander

2014-01-01

We report the successful test flight of a device for generating and monitoring correlated photon pairs under near-space conditions up to 35.5 km altitude. Data from ground based qualification tests and the high altitude experiment demonstrate that the device continues to operate even under harsh environmental conditions. The design of the rugged, compact and power-efficient photon pair system is presented. This design enables autonomous photon pair systems to be deployed on low-resource platforms such as nanosatellites hosting remote nodes of a quantum key distribution network. These results pave the way for tests of entangled photon technology in low earth orbit. PMID:25219935

Workshop on Heteroepitaxial InP Solar Cells

NASA Technical Reports Server (NTRS)

Weinberg, I.; Walters, R. W.

1993-01-01

In a generic sense, the justification for any sort of InP solar cell research applies, i.e. to take advantage of the inherently high radiation resistance and efficiency of InP solar cells. To be more specific, the approach is justified by its potential for significant cost reduction and the availability of greatly increased cell area afforded by substrates such as Si and Ge. The use of substrates, such as the latter two, would result in increased ruggedness, ease of handling, and improved manufacturability. The use of more rugged substrates would lead to a greatly increased capability for cell thinning leading to the desirable feature of reduced array weight.

Expendable bubble tiltmeter for geophysical monitoring

USGS Publications Warehouse

Westphal, J.A.; Carr, M.A.; Miller, W.F.; Dzurisin, D.

1983-01-01

An unusually rugged highly sensitive and inexpensive bubble tiltmeter has been designed, tested, and built in quantity. These tiltmeters are presently used on two volcanoes and an Alaskan glacier, where they continuously monitor surface tilts of geological interest. This paper discusses the mechanical, thermal, and electric details of the meter, and illustrates its performance characteristics in both large (>10-4 radian) and small (<10-6 radian) tilt environments. The meter's ultimate sensitivity is better than 2??10-8 radians rms for short periods (hours), and its useful dynamic range is greater than 10 4. Included is a short description of field use of the instrument for volcano monitoring.

Quantitative Detection of Combustion Species using Ultra-Violet Diode Lasers

NASA Technical Reports Server (NTRS)

Pilgrim, J. S.; Peterson, K. A.

2001-01-01

Southwest Sciences is developing a new microgravity combustion diagnostic based on UV diode lasers. The instrument will allow absolute concentration measurements of combustion species on a variety of microgravity combustion platforms including the Space Station. Our approach uses newly available room temperature UV diode lasers, thereby keeping the instrument compact, rugged and energy efficient. The feasibility of the technique was demonstrated by measurement of CH radicals in laboratory flames. Further progress in fabrication technology of UV diode lasers at shorter wavelengths and higher power will result in detection of transient species in the deeper UV. High sensitivity detection of combustion radicals is provided with wavelength modulation absorption spectroscopy.

Development and test of a Microwave Ice Accretion Measurement Instrument (MIAMI)

NASA Technical Reports Server (NTRS)

Magenheim, B.; Rocks, J. K.

1982-01-01

The development of an ice accretion measurement instrument that is a highly sensitive, accurate, rugged and reliable microprocessor controlled device using low level microwave energy for non-instrusive real time measurement and recording of ice growth history, including ice thickness and accretion rate is discussed. Data is displayed and recorded digitally. New experimental data is presented, obtained with the instrument, which demonstrates its ability to measure ice growth on a two-dimensional airfoil. The device is suitable for aircraft icing protection. It may be mounted flush, non-intrusively, on any part of an aircraft skin including rotor blades and engine inlets.

An inexpensive, multipurpose physical pendulum

NASA Astrophysics Data System (ADS)

Schultz, David

2012-10-01

The pendulum is a highly versatile tool for teaching physics. Many special purpose pendula for student experiments have been described.1-4 In this paper, I describe an inexpensive, multipurpose physical pendulum that can function as both a variable gravity and ballistic pendulum. I designed the apparatus for use in a rotational dynamics unit of the AP Physics C mechanics course. The use of a bike wheel hub pivot allows for low-friction, rugged operation that yields results commensurate with those obtained with much more expensive pendula available on the market (typically 500 per unit5), placing these types of experiments within reach of the teacher on a restricted budget.

Dust in the wind: challenges for urban aerodynamics

NASA Astrophysics Data System (ADS)

Boris, Jay P.

2007-04-01

The fluid dynamics of airflow through a city controls the transport and dispersion of airborne contaminants. This is urban aerodynamics, not meteorology. The average flow, large-scale fluctuations and turbulence are closely coupled to the building geometry. Buildings create large "rooster-tail" wakes; there are systematic fountain flows up the backs of tall buildings; and dust in the wind can move perpendicular to or even against the locally prevailing wind. Requirements for better prediction accuracy demand time-dependent, three-dimensional CFD computations that include solar heating and buoyancy, complete landscape and building geometry specification including foliage and, realistic wind fluctuations. This fundamental prediction capability is necessary to assess urban visibility and line-of-sight sensor performance in street canyons and rugged terrain. Computing urban aerodynamics accurately is clearly a time-dependent High Performance Computing (HPC) problem. In an emergency, on the other hand, prediction technology to assess crisis information, sensor performance, and obscured line-of-sight propagation in the face of industrial spills, transportation accidents, or terrorist attacks has very tight time requirements that suggest simple approximations which tend to produce inaccurate results. In the past we have had to choose one or the other: a fast, inaccurate model or a slow accurate model. Using new fluid-dynamic principles, an urban-oriented emergency assessment system called CT-Analyst® was invented that solves this dilemma. It produces HPC-quality results for airborne contaminant scenarios nearly instantly and has unique new capabilities suited to sensor optimization. This presentation treats the design and use of CT-Analyst and discusses the developments needed for widespread use with advanced sensor and communication systems.

A convenient ultrasound-assisted saponification for the simultaneous determination of vitamin E isomers in vegetable oil by HPLC with fluorescence detection.

PubMed

Yang, Yi; Lu, Dan; Yin, Shuo; Yang, Danni; Chen, Yaling; Li, Yongxin; Sun, Chengjun

2018-04-01

An efficient ultrasound-assisted saponification was developed for simultaneous determination of vitamin E isomers in vegetable oil by high-performance liquid chromatography with fluorescence detection. The samples were saponified ultrasonically with potassium hydroxide solution for only 7 min, then the analytes were extracted with ether. Vitamin E isomers were separated on a C 18 column at 25°C with a mobile phase of methanol/acetonitrile (81:19, v/v) at a flow rate of 0.8 mL/min. Fluorescence detection was operated at 290 nm of excitation wavelength and 327 nm of emission wavelength. Under the optimized conditions, good linearities over the range of 0.001-8.00 μg/mL (r > 0.999) were obtained. Mean recoveries of the method were 88.0-106%, with intra- and interday RSDs less than 11.8 and 12.8%, respectively. The detection limits and quantification limits of the method were 0.30-1.8 and 1.0-6.1 μg/kg, respectively. The recoveries of this method were much higher than that of the quick, easy, cheap, effective, rugged, and safe method and direct dilution method, but were similar to those of hot saponification. This proposed method provides reliable, simple, and rapid quantification of vitamin E isomers in vegetable oils. Five kinds of vegetable oils were analyzed, the quantification results were within the ranges reported by other authors. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

A statistical approach to determine fluxapyroxad and its three metabolites in soils, sediment and sludge based on a combination of chemometric tools and a modified quick, easy, cheap, effective, rugged and safe method.

PubMed

Li, Shasha; Liu, Xingang; Zhu, Yulong; Dong, Fengshou; Xu, Jun; Li, Minmin; Zheng, Yongquan

2014-09-05

An effective method for the quantification of fluxapyroxad and its three metabolites in soils, sediment and sludge was developed using ultrahigh performance chromatography coupled with tandem mass spectrometry (UHPLC-MS/MS). Both the extraction and clean-up steps of the QuEChERS procedure were optimised using a chemometric tool, which was expected to facilitate the rapid analysis with minimal procedures. Several operating parameters (MeCN/acetic acid ratio in the extraction solution (i.e., acetic acid percentage), water volume, extraction time, PSA amount, C18 amount, and GCB amount) were investigated using a Plackett-Burman (P-B) screening design. Afterward, the significant factors (acetic acid percentage, water volume, and PSA amount) obtained were optimised using central composite design (CCD) combined with the desirability function (DF) to determine the optimum experimental conditions. The optimised procedure provides high-level linearity for all studied compounds with correlation coefficients ranging between 0.9972 and 0.9999. The detection limits were in the range of 0.1 to 1.0μg/kg and the limits of quantitation (LOQs) were between 0.5 and 3.4μg/kg with relative standard deviations (RSD) between 2.3% and 9.6% (n=6). Therefore, the developed protocol can serve as a simple and sensitive tool for monitoring fluxapyroxad and its three metabolites in soil, sediment and sludge samples. Copyright © 2014 Elsevier B.V. All rights reserved.

The American Imprint on Alberta Politics

ERIC Educational Resources Information Center

Wiseman, Nelson

2011-01-01

Characteristics assigned to America's classical liberal ideology--rugged individualism, market capitalism, egalitarianism in the sense of equality of opportunity, and fierce hostility toward centralized federalism and socialism--are particularly appropriate for fathoming Alberta's political culture. The author contends that Alberta's early…

Soviet Union Lunar Sample Return Missions

NASA Image and Video Library

2010-03-15

On February 21, 1972, Luna 20 soft landed in the rugged highlands between Mare Fecunditatis and Mare Crisium. The Luna 20 descent stage still sits silently on the Moon, clearly visible in this image taken by NASA Lunar Reconnaissance Orbiter.

78 FR 62443 - Perfluoroalkyl Sulfonates and Long-Chain Perfluoroalkyl Carboxylate Chemical Substances; Final...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-10-22

... manufacturing and petroleum refineries. Carpet and rug mills (NAICS code 314110). Fiber, yarn, and thread mills... the abrasion of carpets. This is of particular concern for children since they engage in a variety of...

Instrumentation of Navistar truck for data collection.

DOT National Transportation Integrated Search

2013-01-01

The overarching goal of this project was to instrument the new MnDOT Navistar truck used at MN Road. A : rugged data acquisition, data recording and wireless transmission system was established for collection of various : sensor signals from the truc...

16 CFR 1630.1 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-01-01

...) Traffic Surface means a surface of a carpet or rug which is intended to be walked upon. (f) Timed Burning.../gram, a mass of 150 mg ±5mg and a nominal diameter of 6mm. (g) Fire-Retardant Treatment means any...

Analyzing Contingency Contracting Purchases for Operation Iraqi Freedom (Unrestricted Version)

DTIC Science & Technology

2008-01-01

that could inform such strategic purchasing decisions. 14 We used the unique contract identification number to check for cross -organization...beds, mattresses, dressers , footlockers) Other (stools, rugs, seats, cabinets, tables, folding chairs, paintings) Generators Various power generators

Package Holds Five Monolithic Microwave Integrated Circuits

NASA Technical Reports Server (NTRS)

Mysoor, Narayan R.; Decker, D. Richard; Olson, Hilding M.

1996-01-01

Packages protect and hold monolithic microwave integrated circuit (MMIC) chips while providing dc and radio-frequency (RF) electrical connections for chips undergoing development. Required to be compact, lightweight, and rugged. Designed to minimize undesired resonances, reflections, losses, and impedance mismatches.

Morphologic and thermophysical characteristics of lava flows southwest of Arsia Mons, Mars

NASA Astrophysics Data System (ADS)

Crown, David A.; Ramsey, Michael S.

2017-08-01

The morphologic and thermophysical characteristics of part of the extensive lava flow fields southwest of Arsia Mons (22.5-27.5°S, 120-130°W) have been examined using a combination of orbital VNIR and TIR datasets. THEMIS images provide context for the regional geology and record diurnal temperature variability that is diverse and unusual for flow surfaces in such close proximity. CTX images were used to distinguish dominant flow types and assess local age relationships between individual lava flows. CTX and HiRISE images provide detailed information on flow surface textures and document aeolian effects as they reveal fine-grained deposits in many low-lying areas of the flow surfaces as well as small patches of transverse aeolian ridges. Although this region is generally dust-covered and has a lower overall thermal inertia, the THEMIS data indicate subtle spectral variations within the population of lava flows studied. These variations could be due to compositional differences among the flows or related to mixing of flow and aeolian materials. Specific results regarding flow morphology include: a) Two main lava flow types (bright, rugged and dark, smooth as observed in CTX images) dominate the southwest Arsia Mons/NE Daedalia Planum region; b) the bright, rugged flows have knobby, ridged, and/or platy surface textures, commonly have medial channel/levee systems, and may have broad distal lobes; c) the dark, smooth flows extend from distributary systems that consist of combinations of lava channels, lava tubes, and/or sinuous ridges and plateaus; and d) steep-sided, terraced margins, digitate breakout lobes, and smooth-surfaced plateaus along lava channel/tube systems are interpreted as signatures of flow inflation within the dark, smooth flow type. These flows exhibit smoother upper surfaces, are thinner, and have more numerous, smaller lobes, which, along with their the channel-/tube-fed nature, indicate a lower viscosity lava than for the bright, rugged flows. Flow patterns and local interfingering and overlapping relationships are delineated in CTX images and allow reconstruction of the complex flow field surfaces. Darker channel-/tube-fed flows are generally younger than adjacent thicker, bright, rugged flows; however, the diversity and complexity of temporal relationships observed, along with the thermophysical variability, suggests that lava sources with different eruptive styles and magnitudes and/or lavas that experienced different local emplacement conditions were active contemporaneously.

RAPA: a novel in vitro method to evaluate anti-bacterial skin cleansing products.

PubMed

Ansari, S A; Gafur, R B; Jones, K; Espada, L A; Polefka, T G

2010-04-01

Development of efficacious anti-bacterial skin cleansing products has been limited by the availability of a pre-clinical (in vitro) method to predict clinical efficacy adequately. We report a simple and rapid method, designated as rapid agar plate assay (RAPA), that uses the bacteriological agar surface as a surrogate substrate for skin and combines elements of two widely used in vivo (clinical) methods (Agar Patch and Cup Scrub). To simulate the washing of the human hand or forearm skin with the test product, trypticase soy agar plates were directly washed with the test product and rinsed under running tap water. After air-drying the washed plates, test bacteria (Staphylococcus aureus or Escherichia coli) were applied and the plates were incubated at 37 degrees C for 18-24 h. Using S. aureus as the test organism, anti-bacterial bar soap containing triclocarbanilide showed a strong linear relationship (R(2) = 0.97) between bacterial dose and their per cent reduction. A similar dose-response relationship (R(2) = 0.96) was observed for anti-bacterial liquid hand soap against E. coli. RAPA was able to distinguish between anti-bacterial products based on the nature and level of actives in them. In limited comparative tests, results obtained by RAPA were comparable with the results obtained by clinical agar patch and clinical cup scrub methods. In conclusion, RAPA provides a simple, rugged and reproducible in vitro method for testing the relative efficacy of anti-bacterial skin cleansing products with a likelihood of comparable clinical efficacy. Further testing is warranted to improve the clinical predictability of this method.

Practical estimates of field-saturated hydraulic conductivity of bedrock outcrops using a modified bottomless bucket method

USGS Publications Warehouse

Mirus, Benjamin B.; Perkins, Kim S.

2012-01-01

The bottomless bucket (BB) approach (Nimmo et al., 2009a) is a cost-effective method for rapidly characterizing field-saturated hydraulic conductivity Kfs of soils and alluvial deposits. This practical approach is of particular value for quantifying infiltration rates in remote areas with limited accessibility. A similar approach for bedrock outcrops is also of great value for improving quantitative understanding of infiltration and recharge in rugged terrain. We develop a simple modification to the BB method for application to bedrock outcrops, which uses a non-toxic, quick-drying silicone gel to seal the BB to the bedrock. These modifications to the field method require only minor changes to the analytical solution for calculating Kfs on soils. We investigate the reproducibility of the method with laboratory experiments on a previously studied calcarenite rock and conduct a sensitivity analysis to quantify uncertainty in our predictions. We apply the BB method on both bedrock and soil for sites on Pahute Mesa, which is located in a remote area of the Nevada National Security Site. The bedrock BB tests may require monitoring over several hours to days, depending on infiltration rates, which necessitates a cover to prevent evaporative losses. Our field and laboratory results compare well to Kfs values inferred from independent reports, which suggests the modified BB method can provide useful estimates and facilitate simple hypothesis testing. The ease with which the bedrock BB method can be deployed should facilitate more rapid in-situ data collection than is possible with alternative methods for quantitative characterization of infiltration into bedrock.

Quantitative analysis of eletriptan in human plasma by HPLC-MS/MS and its application to pharmacokinetic study.

PubMed

Ponnuru, Venkata Suresh; Challa, B R; Nadendla, Ramarao

2011-11-01

Authors developed a simple, sensitive, selective, rapid, rugged, and reproducible liquid chromatography-tandem mass spectrometry method for the quantification of eletriptan (EP) in human plasma using naratriptan (NP) as an internal standard (IS). Chromatographic separation was performed on Ascentis Express C18, 50 × 4.6 mm, 2.7 μm column. Mobile phase was composed of 0.1% formic acid: methanol (40:60 v/v), with 0.5 mL/min flow rate. Drug and IS were extracted by liquid-liquid extraction. EP and NP were detected with proton adducts at m/z 383.2→84.3 and 336.2→97.8 in multiple reaction monitoring (MRM) positive mode, respectively. The method was validated with the correlation coefficients of (r(2)) ≥ 0.9963 over a linear concentration range of 0.5-250.0 ng/mL. This method demonstrated intra- and inter-day precision within 1.4-9.2% and 4.4-5.5% and accuracy within 96.8-103% and 98.5-99.8% for EP. This method is successfully applied in the bioequivalence study of 24 human volunteers.

Instrument for Aircraft-Icing and Cloud-Physics Measurements

NASA Technical Reports Server (NTRS)

Lilie, Lyle; Bouley, Dan; Sivo, Chris

2006-01-01

The figure shows a compact, rugged, simple sensor head that is part of an instrumentation system for making measurements to characterize the severity of aircraft-icing conditions and/or to perform research on cloud physics. The quantities that are calculated from measurement data acquired by this system and that are used to quantify the severity of icing conditions include sizes of cloud water drops, cloud liquid water content (LWC), cloud ice water content (IWC), and cloud total water content (TWC). The sensor head is mounted on the outside of an aircraft, positioned and oriented to intercept the ambient airflow. The sensor head consists of an open housing that is heated in a controlled manner to keep it free of ice and that contains four hot-wire elements. The hot-wire sensing elements have different shapes and sizes and, therefore, exhibit different measurement efficiencies with respect to droplet size and water phase (liquid, frozen, or mixed). Three of the hot-wire sensing elements are oriented across the airflow so as to intercept incoming cloud water. For each of these elements, the LWC or TWC affects the power required to maintain a constant temperature in the presence of cloud water.

Multifunctional Cooling Garment for Space Suit Environmental Control

NASA Technical Reports Server (NTRS)

Izenson, Michael; Chen, Weibo; Phillips, Scott; Chepko, Ariane; Bue, Grant; Ferl, Janet; Cencer, Daniel

2015-01-01

Future manned space exploration missions will require space suits with capabilities beyond the current state of the art. Portable Life Support Systems for these future space suits face daunting challenges, since they must maintain healthy and comfortable conditions inside the suit for long-duration missions while minimizing weight and water venting. We have demonstrated the feasibility of an innovative, multipurpose garment for thermal and humidity control inside a space suit pressure garment that is simple, rugged, compact, and lightweight. The garment is a based on a conventional liquid cooling and ventilation garment (LCVG) that has been modified to directly absorb latent heat as well as sensible heat. This hybrid garment will prevent buildup of condensation inside the pressure garment, prevent loss of water by absorption in regenerable CO2 removal beds, and conserve water through use of advanced lithium chloride absorber/radiator (LCAR) technology for nonventing heat rejection. We have shown the feasibility of this approach by sizing the critical components for the hybrid garment, developing fabrication methods, building and testing a proof-of-concept system, and demonstrating by test that its performance is suitable for use in space suit life support systems.

Multifunctional Cooling Garment for Space Suit Environmental Control

NASA Technical Reports Server (NTRS)

Izenson, Michael G.; Chen, Weibo; Phillips, Scott; Chepko, Ariane; Bue, Grant; Ferl, Janet

2014-01-01

Future manned space exploration missions will require space suits with capabilities beyond the current state of the art. Portable Life Support Systems for these future space suits face daunting challenges, since they must maintain healthy and comfortable conditions inside the suit for longduration missions while minimizing weight and water venting. We have demonstrated the feasibility of an innovative, multipurpose garment for thermal and humidity control inside a space suit pressure garment that is simple, rugged, compact, and lightweight. The garment is a based on a conventional liquid cooling and ventilation garment (LCVG) that has been modified to directly absorb latent heat as well as sensible heat. This hybrid garment will prevent buildup of condensation inside the pressure garment, prevent loss of water by absorption in regenerable CO2 removal beds, and conserve water through use of advanced lithium chloride absorber/radiator (LCAR) technology for nonventing heat rejection. We have shown the feasibility of this approach by sizing the critical components for the hybrid garment, developing fabrication methods, building and testing a proof-of-concept system, and demonstrating by test that its performance is suitable for use in space suit life support systems.

Nanomechanical architecture of semiconductor nanomembranes.

PubMed

Huang, Minghuang; Cavallo, Francesca; Liu, Feng; Lagally, Max G

2011-01-01

Semiconductor nanomembranes are single-crystal sheets with thickness ranging from 5 to 500nm. They are flexible, bondable, and mechanically ultra-compliant. They present a new platform to combine bottom-up and top-down semiconductor processing to fabricate various three-dimensional (3D) nanomechanical architectures, with an unprecedented level of control. The bottom-up part is the self-assembly, via folding, rolling, bending, curling, or other forms of shape change of the nanomembranes, with top-down patterning providing the starting point for these processes. The self-assembly to form 3D structures is driven by elastic strain relaxation. A variety of structures, including tubes, rings, coils, rolled-up "rugs", and periodic wrinkles, has been made by such self-assembly. Their geometry and unique properties suggest many potential applications. In this review, we describe the design of desired nanostructures based on continuum mechanics modelling, definition and fabrication of 2D strained nanomembranes according to the established design, and release of the 2D strained sheet into a 3D or quasi-3D object. We also describe several materials properties of nanomechanical architectures. We discuss potential applications of nanomembrane technology to implement simple and hybrid functionalities.

Quantification, dissipation behavior and risk assessment of ethion in green pea by gas chromatography-electron capture detector.

PubMed

Jan, Ishrat; Dar, Alamgir A; Mubashir, Sofi; Alam Wani, Ashraf; Mukhtar, Malik; Sofi, Khurshid A; Dar, Irshad H; Sofi, Javid A

2018-05-01

Residue investigation was carried out to scrutinize the persistence, dissipation behavior, half-life, and risk assessment of ethion on green pea fruit by spraying ethion at the fruiting stage followed by another application at 10 day intervals. The samples were extracted by using a quick, easy, low-cost, effective, rugged, and safe method, and the residues of ethion were analyzed by gas chromatography with electron capture detection. Here we report a novel, accurate, and cost-effective gas chromatography method for the determination of average deposits of ethion on green pea. The initial deposits were found to be 4.65 mg/kg following the application of insecticide. Residues of ethion reached below the detection limit of 0.10 mg/kg after 25 days at recommended dosage. The half-life of ethion was found to be 4.62 days. For risk assessment studies, the 25th day will be safe for consumers for the consumption of green peas. The developed method is simple, sensitive, selective, and repeatable and can be extended for ethion-based standardization of herbal formulations containing green pea and its use in pesticide industries. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Risk assessment, dissipation behavior and persistence of quinalphos in/on green pea by gas chromatography with electron capture detector.

PubMed

Dar, Alamgir A; Jan, Ishrat; Wani, Ashraf A; Mubashir, Sofi; Sofi, Khurshid A; Sofi, Javid A; Dar, Irshad H

2018-06-01

Chemical investigation was carried out to examine the risk assessment, dissipation behavior, persistence, and half-life period of quinalphos in/on green pea fruit by spraying quinalphos at fruiting stage followed by another application after 10-day interval. The samples were extracted by using the quick, easy, cheap, effective, rugged, and safe method, and the residues of quinalphos were analyzed by gas chromatography with electron capture detector. Herein, we report a novel, accurate, and cost-effective gas chromatography method for the determination of average deposits of quinalphos in/on green pea. The initial deposits and half-life of quinalphos were found to be 1.20 mg/kg and 2.77 days, respectively, following the application of insecticide. Residues of quinalphos reached below detection limit of 0.05 mg/kg after 10 days at recommended dosage. For risk assessment studies, the tenth day will be safe for consumers for consumption of green pea. The developed method is simple, selective, and repeatable, and it can be extended for quinalphos-based standardization of herbal formulations containing green pea and its use in pesticide industries. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Rugged spin-polarized electron sources based on negative electron affinity GaAs photocathode with robust Cs2Te coating

NASA Astrophysics Data System (ADS)

Bae, Jai Kwan; Cultrera, Luca; DiGiacomo, Philip; Bazarov, Ivan

2018-04-01

Photocathodes capable of providing high intensity and highly spin-polarized electron beams with long operational lifetimes are of great interest for the next generation nuclear physics facilities like Electron Ion Colliders. We report on GaAs photocathodes activated by Cs2Te, a material well known for its robustness. GaAs activated by Cs2Te forms Negative Electron Affinity, and the lifetime for extracted charge is improved by a factor of 5 compared to that of GaAs activated by Cs and O2. The spin polarization of photoelectrons was measured using a Mott polarimeter and found to be independent from the activation method, thereby shifting the paradigm on spin-polarized electron sources employing photocathodes with robust coatings.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sanchez, R.O.

Voltage breakdowns become a major concern in reducing the size of high-voltage power converter transformers. Even the smallest of voids can provide a path for corona discharge which can cause a dielectric breakdown leading to a transformer failure. A method of encapsulating small high voltage transformers has been developed. The method virtually eliminates voids in the impregnation material, provides an exceptional dielectric between windings and provides a mechanically rugged package. The encapsulation material is a CTBN modified mica filled epoxy. The method requires heat/vacuum to impregnate the coil and heat/pressure to cure the encapsulant. The transformer package utilizes a Diallylmore » Phthalate (DAP) contact assembly in which a coated core/coil assembly is mounted and soldered. This assembly is then loaded into an RTV mold and the encapsulation process begins.« less

Seeing laser scalpel: a novel monolithic high-power diode pumped Tm:YAG laser system at 2.02 μm with double-clad fiber combined OCT

NASA Astrophysics Data System (ADS)

Messner, Manuel; Heinrich, Arne; Hagen, Clemens; Unterrainer, Karl

2017-02-01

We report on a novel monolithic high-power diode pumped Tm:YAG laser at 2.02 μm. The pulsed laser generates average output power and pulse energy of beyond 90W and 900mJ in 400 μs pulses, respectively. This wavelength allows usage of standard fused silica fibers and optics, a price competitive solution for minimally-invasive endoscopic surgery. Recent developments in double-clad fiber combiners enable a rugged delivery system for the laser and the OCT ideal for a seeing laser scalpel. This gives the possibility to detect in-depth underlying tissue not yet ablated by the laser in a 2D or 3D fashion with micrometer resolution.

Acousto-optic time- and space-integrating spotlight-mode SAR processor

NASA Astrophysics Data System (ADS)

Haney, Michael W.; Levy, James J.; Michael, Robert R., Jr.

1993-09-01

The technical approach and recent experimental results for the acousto-optic time- and space- integrating real-time SAR image formation processor program are reported. The concept overcomes the size and power consumption limitations of electronic approaches by using compact, rugged, and low-power analog optical signal processing techniques for the most computationally taxing portions of the SAR imaging problem. Flexibility and performance are maintained by the use of digital electronics for the critical low-complexity filter generation and output image processing functions. The results include a demonstration of the processor's ability to perform high-resolution spotlight-mode SAR imaging by simultaneously compensating for range migration and range/azimuth coupling in the analog optical domain, thereby avoiding a highly power-consuming digital interpolation or reformatting operation usually required in all-electronic approaches.

Sydney

Atmospheric Science Data Center

2013-04-16

... metropolitan area. This city is host to the 2000 Olympic Games, which opened Friday, September 15. Sydney Harbour is the rugged-shaped ... central city area. Olympic Park, the main venue for the Games, is on a southern arm of the harbor, about 20 kilometers from the coast. ...

Beneficial utilization of lime sludge for subgrade stabilization, a pilot study : executive summary report.

DOT National Transportation Integrated Search

2010-06-01

A global chemical stabilization design is recently : adopted by the Ohio Department of Transportation : (ODOT). This produces performance and economic : benefits in providing pavement with a rugged base : supporting. Given the large quantities of lim...

Beneficial Utilization of Lime Sludge for Subgrade Stabilization : a Pilot study : Executive Summary Report

DOT National Transportation Integrated Search

2010-06-01

A global chemical stabilization design is recently : adopted by the Ohio Department of Transportation : (ODOT). This produces performance and economic : benefits in providing pavement with a rugged base : supporting. Given the large quantities of lim...

Morocco and Algeria

Atmospheric Science Data Center

2013-04-15

... mosaic of southwestern Europe and northwestern Morocco and Algeria. The image extends from 48°N, 16°W in the northwest to 32°N, 8°E in ... corner. The rugged Atlas Mountain ranges traverse northern Algeria and Morocco. The Multi-angle Imaging SpectroRadiometer (MISR) ...

LASER FLUORESCENCE EEM PROBE FOR CONE PENETROMETER POLLUTION ANALYSIS

EPA Science Inventory

A fiber optic LIF (Laser induced fluorescence) EEM (Excitation emission matrix) instrument for CPT deployment has been successfully developed and field tested. The system employs a Nd: YAG laser and Raman shifter as a rugged field portable excitation source. This excitation sou...

UNCERTAINTY IN SCALING NUTRIENT EXPORT COEFFICIENTS

EPA Science Inventory

The Innov-X XT400 portable XRF analyzer features a miniature, rugged x-ray tube excitation source for analyzing a wide variety of elements and sample materials, including alloys, environmental solids, and other analytical samples. The x-ray tube source and Light Element Analysis...

Miniature Incandescent Lamps as Fiber-Optic Light Sources

NASA Technical Reports Server (NTRS)

Tuma, Margaret; Collura, Joe; Helvajian, Henry; Pocha, Michael; Meyer, Glenn; McConaghy, Charles F.; Olsen, Barry L.

2008-01-01

Miniature incandescent lamps of a special type have been invented to satisfy a need for compact, rapid-response, rugged, broadband, power-efficient, fiber-optic-coupled light sources for diverse purposes that could include calibrating spectrometers, interrogating optical sensors, spot illumination, and spot heating.

Method Development and Monitoring of Cyanotoxins in Water (ACS Central Presentation)

EPA Science Inventory

Increasing occurrence of cyanobacterial harmful algal blooms (HABs) in ambient waters has become a worldwide concern. Numerous cyanotoxins can be produced during HAB events which are toxic to animals and humans. Validated standardized methods that are rugged, selective and sensit...

High-performance fiber optic link for ECM antenna remoting

NASA Astrophysics Data System (ADS)

Edge, Colin; Burgess, John W.; Wale, Michael J.; Try, Nicholas W.

1998-11-01

The ability to remotely radiate microwave signals has become an essential feature of modern electronic counter-measures (ECM) systems. The use of fiber optics allows remote microwave links to be constructed which have very low propagation loss and dispersion, are very flexible and light in weight, and have a high degree of immunity from external electromagnetic fields, crosstalk and environmental effects. This combination of desirable characteristics are very beneficial to avionic ECM antenna remoting as well as many other applications. GEC-Marconi have developed high performance fiber components for use in a towed radar decoy. The resulting rugged and compact optical transmitter and receiver modules have been developed and proven to maintain the required performance over the full hostile range of environmental conditions encountered on a fast jet. Packaged fiber optic links have been produced which can achieve a compression dynamic range of greater than 87 dB in 1 MHz bandwidth over a 2 to 18 GHz.

Feedthrough terminal for high-power cell

DOEpatents

Kaun, T.D.

1982-05-28

A feedthrough terminal for a high power electrochemical storage cell providing low resistance coupling to the conductive elements therein while isolating the terminal electrode from the highly corrosive environment within the cell is disclosed. A large diameter, cylindrical copper electrode is enclosed in a stainless steel tube with a BN powder feedthrough seal maintained around the stainless steel tube by means of facing insulative bushings and an outer sleeve. One end of the copper conductor is silver-brazed directly to a flat, butterfly bus bar within the cell, with the adjacent end of the surrounding outer feedthrough sleeve welded to the bus bar. A threaded seal is fixedly positioned on a distal portion of the stainless steel tube immediately adjacent the distal insulative bushing so as to compress the feedthrough seal in tight fitting relation around the stainless steel tube in providing a rugged, leak-proof electrical feedthrough terminal for the power cell.

High efficiency direct thermal to electric energy conversion from radioisotope decay using selective emitters and spectrally tuned solar cells

NASA Technical Reports Server (NTRS)

Chubb, Donald L.; Flood, Dennis J.; Lowe, Roland A.

1993-01-01

Thermophotovoltaic (TPV) systems are attractive possibilities for direct thermal-to-electric energy conversion, but have typically required the use of black body radiators operating at high temperatures. Recent advances in both the understanding and performance of solid rare-earth oxide selective emitters make possible the use of TPV at temperatures as low as 1200K. Both selective emitter and filter system TPV systems are feasible. However, requirements on the filter system are severe in order to attain high efficiency. A thin-film of a rare-earth oxide is one method for producing an efficient, rugged selective emitter. An efficiency of 0.14 and power density of 9.2 W/KG at 1200K is calculated for a hypothetical thin-film neodymia (Nd2O3) selective emitter TPV system that uses radioisotope decay as the thermal energy source.

Investigation of geophysical fields in pyrite deposits under mountainous conditions

NASA Astrophysics Data System (ADS)

Khesin, B. E.; Alexeyev, V. V.; Eppelbaum, L. V.

1993-05-01

Geophysical surveys under mountainous conditions are generally complicated by various noises, primarily by rugged topography effects. A rational integration of mobile geophysical methods (gravity prospecting, magnetic prospecting and VLF technique has been substantiated and effective methods of interpretation have been developed for copper pyrite deposits of a Kuroko type (an important source of non-ferrous and noble metals) not infrequently occurring in mountainous regions. A special scheme for obtaining the Bouguer anomalies has been employed to suppress the terrain relief effects dampening the anomaly effects from the objects of prospecting. The scheme is based on calculating the difference between the free-air anomaly ( Δg F.a) and the field determined from a 3-D model of a uniform medium with a real topography. This scheme almost doubled the accuracy of the Δg B chart. The further interpretation includes the following basic steps: (1) singling out the object of search using summation of the amounts of information obtained in various fields; (2) revision of the geological section using the methods specially devised for quantitative interpretation of anomalies under conditions of a rugged topography, inclined polarization and an unknown level of the normal field; and (3) physical-geological simulation realized as man-computer selection with the use of an effective algorithm for solving a direct 3-D problem of gravity and magnetic prospecting under the conditions of complex mediums and rugged observation surfaces. The method has been successfully tested at various stages of geophysical investigation under a variety of geological conditions, including saturated prospecting on the Kuroko-type Kyzylbulakh deposit (Lesser Caucasus) which has been thoroughly investigated by mining and drilling operations.

One-Piece Force-Transducer Body

NASA Technical Reports Server (NTRS)

Meyer, R. A.

1986-01-01

Rugged unit designed to operate in severe environment. Forcetransducer body designed for measurement of loads on specimens tested in hydrogen gas at temperatures up to 2,000 degree F (1,090 degree C). Body has symmetrical radial-shear-beam configuration and machined in one piece from bar stock.

METHOD OF CHEMICAL ANALYSIS FOR OIL SHALE WASTES

EPA Science Inventory

Several methods of chemical analysis are described for oil shale wastewaters and retort gases. These methods are designed to support the field testing of various pollution control systems. As such, emphasis has been placed on methods which are rapid and sufficiently rugged to per...

Pilot study on rugged fiber optic brillouin sensors for large-strain measurements to ensure the safety of transportation structures.

DOT National Transportation Integrated Search

2012-07-01

Brillouin-scattering Optical Time Domain Reflectometry (BOTDR) is a viable technology for simultaneous, distributed : strain and temperature measurements for miles-long transportation structures. It is a promising tool to ensure the smooth : operatio...

NASA Spacecraft Images New Mexico Wildfire

NASA Image and Video Library

2013-07-02

NASA Terra spacecraft passed over the Silver Fire in western New Mexico on June 7, 2013. It has since consumed more than 137,000 acres of timber in a rugged area of the Gila National Forest that has not seen large fires for nearly a century.

42 CFR 71.50 - Scope and definitions.

Code of Federal Regulations, 2014 CFR

2014-10-01

... importations of various animal hosts or vectors or other etiological agents from foreign countries into the... the following meanings: Animal product or Product means the hide, hair, skull, teeth, bones, claws, blood, tissue, or other biological samples from an animal, including trophies, mounts, rugs, or other...

42 CFR 71.50 - Scope and definitions.

Code of Federal Regulations, 2013 CFR

2013-10-01

... importations of various animal hosts or vectors or other etiological agents from foreign countries into the... the following meanings: Animal product or Product means the hide, hair, skull, teeth, bones, claws, blood, tissue, or other biological samples from an animal, including trophies, mounts, rugs, or other...

Multiple, Distinct Isoforms of Sucrose Synthase in Pea1

PubMed Central

Barratt, D.H. Paul; Barber, Lorraine; Kruger, Nicholas J.; Smith, Alison M.; Wang, Trevor L.; Martin, Cathie

2001-01-01

Genes encoding three isoforms of sucrose synthase (Sus1, Sus2, and Sus3) have been cloned from pea (Pisum sativum). The genes have distinct patterns of expression in different organs of the plant, and during organ development. Studies of the isoforms expressed as recombinant proteins in Escherichia coli show that they differ in kinetic properties. Although not of great magnitude, the differences in properties are consistent with some differentiation of physiological function between the isoforms. Evidence for differentiation of function in vivo comes from the phenotypes of rug4 mutants of pea, which carry mutations in the gene encoding Sus1. One mutant line (rug4-c) lacks detectable Sus1 protein in both the soluble and membrane-associated fractions of the embryo, and Sus activity in the embryo is reduced by 95%. The starch content of the embryo is reduced by 30%, but the cellulose content is unaffected. The results imply that different isoforms of Sus may channel carbon from sucrose towards different metabolic fates within the cell. PMID:11598239

Evaluating Mass Analyzers as Candidates for Small, Portable, Rugged Single Point Mass Spectrometers for Analysis of Permanent Gases

NASA Technical Reports Server (NTRS)

Arkin, C. Richard; Ottens, Andrew K.; Diaz, Jorge A.; Griffin, Timothy P.; Follestein, Duke; Adams, Fredrick; Steinrock, T. (Technical Monitor)

2001-01-01

For Space Shuttle launch safety, there is a need to monitor the concentration Of H2, He, O2, and Ar around the launch vehicle. Currently a large mass spectrometry system performs this task, using long transport lines to draw in samples. There is great interest in replacing this stationary system with several miniature, portable, rugged mass spectrometers which act as point sensors which can be placed at the sampling point. Five commercial and two non-commercial analyzers are evaluated. The five commercial systems include the Leybold Inficon XPR-2 linear quadrupole, the Stanford Research (SRS-100) linear quadrupole, the Ferran linear quadrupole array, the ThermoQuest Polaris-Q quadrupole ion trap, and the IonWerks Time-of-Flight (TOF). The non-commercial systems include a compact double focusing sector (CDFMS) developed at the University of Minnesota, and a quadrupole ion trap (UF-IT) developed at the University of Florida.

Coherent lidar airborne wind sensor II: flight-test results at 2 and 10 νm.

PubMed

Targ, R; Steakley, B C; Hawley, J G; Ames, L L; Forney, P; Swanson, D; Stone, R; Otto, R G; Zarifis, V; Brockman, P; Calloway, R S; Klein, S H; Robinson, P A

1996-12-20

The use of airborne laser radar (lidar) to measure wind velocities and to detect turbulence in front of an aircraft in real time can significantly increase fuel efficiency, flight safety, and terminal area capacity. We describe the flight-test results for two coherent lidar airborne shear sensor (CLASS) systems and discuss their agreement with our theoretical simulations. The 10.6-μm CO(2) system (CLASS-10) is a flying brassboard; the 2.02-μm Tm:YAG solid-state system (CLASS-2) is configured in a rugged, light-weight, high-performance package. Both lidars have shown a wind measurement accuracy of better than 1 m/s.

Pluto in Twilight

NASA Image and Video Library

2015-09-10

This image of Pluto from NASA's New Horizons spacecraft, processed in two different ways, shows how Pluto's bright, high-altitude atmospheric haze produces a twilight that softly illuminates the surface before sunrise and after sunset, allowing the sensitive cameras on New Horizons to see details in nighttime regions that would otherwise be invisible. The right-hand version of the image has been greatly brightened to bring out faint details of rugged haze-lit topography beyond Pluto's terminator, which is the line separating day and night. The image was taken as New Horizons flew past Pluto on July 14, 2015, from a distance of 50,000 miles (80,000 kilometers). http://photojournal.jpl.nasa.gov/catalog/PIA19931

Orbital observations of the lunar highlands on Apollo 16 and their interpretation

NASA Technical Reports Server (NTRS)

Mattingly, T. K.; El-Baz, F.

1973-01-01

From orbital altitudes, the lunar highlands display the same surface characteristics on both the far and near sides. Rugged terra and plains forming materials all appear as if dusted with a uniform mantle. No stratigraphy or evidence of layering are seen in highland craters, with the possible exception of South Ray Crater in the Descartes landing site area. Among the discussed small scale features of the lunar highlands are: fine lineaments, that appear to be real rather than artifacts of lighting, on both horizontal and inclined surfaces; ridge-like scarps that cut across highland topography; and benches that are believed to be high lava marks rather than talus accumulates.

Ultra Small Aperture Terminal: System Design and Test Results

NASA Technical Reports Server (NTRS)

Sohn, Philip Y.; Reinhart, Richard C.

1996-01-01

The Ultra Small Aperture Terminal (USAT) has been developed to test and demonstrate remote and broadcast satcom applications via the Advanced Communications Technology Satellite (ACTS). The design of these ground stations emphasize small size, low power consumption, portable and rugged terminals. Each ground station includes several custom design parts such as 35 cm diameter antenna, 1/4 Watt transmitter with built-in upconverter, and 4.0 dB Noise Figure (NF) receiver with built-in downconverter. In addition, state-of-the-art commercial parts such as highly stable ovenized crystal oscillators and dielectric resonator oscillators are used in the ground station design. Presented in this paper are system level design description, performance, and sample applications.

"Beards, Sandals, and Other Signs of Rugged Individualism": Masculine Culture within the Computing Professions.

PubMed

Ensmenger, Nathan

2015-01-01

Over the course of the 1960s and 1970s, male computer experts were able to successfully transform the "routine and mechanical" (and therefore feminized) activity of computer programming into a highly valued, well-paying, and professionally respectable discipline. They did so by constructing for themselves a distinctively masculine identity in which individual artistic genius, personal eccentricity, anti-authoritarian behavior, and a characteristic "dislike of activities involving human interaction" were mobilized as sources of personal and professional authority. This article explores the history of masculine culture and practices in computer programming, with a particular focus on the role of university computer centers as key sites of cultural formation and dissemination.

GOAT ROCKS WILDERNESS AND ADJACENT ROADLESS AREAS, WASHINGTON.

USGS Publications Warehouse

Church, S.E.; Close, T.J.

1984-01-01

The Goat Rocks Wilderness and adjacent roadless areas are a rugged, highly forested, scenic area located on the crest of the Cascade Range in south-central Washington. Several mineral claims have been staked in the area. Mineral surveys were conducted. Geochemical, geophysical, and geologic investigations indicate that three areas have probable mineral-resource potential for base metals in porphyry-type deposits. Available data are not adequate to permit definition of the potential for oil and gas. There is little likelihood for the occurrence of other kinds of energy resources in the area. Evaluation of resource potential in the three areas identified as having probable mineral-resource potential could be improved by more detailed geochemical studies and geologic mapping.

Hawaiian Goose (Branta sandvicensis)

USGS Publications Warehouse

Banko, Paul C.; Black, Jeffrey M.; Banko, Winston E.

1999-01-01

Evolving in the remote Hawaiian Archipelago and having the smallest range of any living goose, the Hawaiian Goose, or better known by its Hawaiian name—Nënë, is among the most isolated, sedentary, and threatened of waterfowl. The Nënë is also highly terrestrial, and several structural features demonstrate its adaptation to life on islands with limited freshwater habitat: It stands taller and more upright than geese of similar weight, enabling it to reach high to browse the fruits, seeds, and foliage that constitute its herbivorous diet; its legs and padded toes are long and strong, promoting swift, sure walking and running over rugged terrain; webbing is reduced between the toes; and though it is a capable swimmer and readily uses freshwater habitats when available, the Nënë does not require freshwater or oceanic habitats in the same way that many other waterfowl do.

Consortium for military LCD display procurement

NASA Astrophysics Data System (ADS)

Echols, Gregg

2002-08-01

International Display Consortium (IDC) is the joining together of display companies to combined their buying power and obtained favorable terms with a major LCD manufacturer. Consolidating the buying power and grouping the demand enables the rugged display industry of avionics, ground vehicles, and ship based display manufacturers to have unencumbered access to high performance AMLCDs while greatly reducing risk and lowering cost. With an unrestricted supply of AMLCD displays, the consortium members have total control of their risk, cost, deliveries and added value partners. Every display manufacturer desires a very close relationship with a display vender. With IDC each consortium member achieves a close relationship. Consortium members enjoy cost effective access to high performance, industry standard sized LCD panels, and modified commercial displays with 100 degree C clearing points and portrait configurations. Consortium members also enjoy proposal support, technical support and long-term support.

Observations of Interchange Between Acceleration and Thermalization Processes in Auroral Electrons. Ph.D. Thesis

NASA Technical Reports Server (NTRS)

Pongratz, M. B.

1972-01-01

The results of high time-resolution measurements of energetic electrons in an auroral break up are presented. Electrons with energies from 500 eV to over 100 keV and pitch angles from 0 to 150 deg were detected with two detectors onboard sounding rocket 18:63 UE. Complete energy spectra were taken every 0.1 seconds. The procedure for cleaning and activating the BeCu dynodes of a small, rugged, high gain electron multiplier is described. A theoretical study of the energy-angular response of a spherical plate electrostatic analyzer is compared to experimental results. An energy spectrum unfolding technique which does not require the assumption of a histogram-type energy spectrum is presented. A method of determining sounding rocket orientation from the output of a single magnetometer is described.

Practical internal combustion engine laser spark plug development

NASA Astrophysics Data System (ADS)

Myers, Michael J.; Myers, John D.; Guo, Baoping; Yang, Chengxin; Hardy, Christopher R.

2007-09-01

Fundamental studies on laser ignition have been performed by the US Department of Energy under ARES (Advanced Reciprocating Engines Systems) and by the California Energy Commission under ARICE (Advanced Reciprocating Internal Combustion Engine). These and other works have reported considerable increases in fuel efficiencies along with substantial reductions in green-house gas emissions when employing laser spark ignition. Practical commercial applications of this technology require low cost high peak power lasers. The lasers must be small, rugged and able to provide stable laser beam output operation under adverse mechanical and environmental conditions. New DPSS (Diode Pumped Solid State) lasers appear to meet these requirements. In this work we provide an evaluation of HESP (High Efficiency Side Pumped) DPSS laser design and performance with regard to its application as a practical laser spark plug for use in internal combustion engines.

Rugged Practices: Embodying Authenticity in Outdoor Recreation

ERIC Educational Resources Information Center

Senda-Cook, Samantha

2012-01-01

When people recreate outdoors, they value the quality of the experience. This study examines rhetorical practices that sustain or undermine perceived authentic outdoor recreation experiences. I conducted a rhetorical analysis of my fieldnotes gathered through participant observation and interview transcripts of online and in-person interviews. I…

WIRELESS ELECTROCHEMICAL CLO2 MONITOR FOR DECONTAMINATION OPERATIONS - PHASE I

EPA Science Inventory

The U.S. Environmental Protection Agency has identified the need for an accurate and field-rugged instrument to monitor chlorine dioxide (ClO₂) for use in monitoring building decontamination operations.

The proposed Phase I study will evaluate the feasibil...

WIRELESS ELECTROCHEMICAL CLO2 MONITOR FOR DECONTAMINATION OPERATIONS - PHASE II

EPA Science Inventory

Recognizing the importance of ClO₂ in disinfection and decontamination operations, the U.S. Environmental Protection Agency (EPA) had identified the need for portable, accurate and field-rugged chlorine dioxide (ClO₂) monitors for use in monitoring buildi...

Steerable K/Ka-Band Antenna For Land-Mobile Satellite Applications

NASA Technical Reports Server (NTRS)

Densmore, Arthur; Jamnejad, Vahraz; Woo, Kenneth

1994-01-01

Prototype steerable microwave antenna tracks and communicates with geostationary satellite. Designed to mount on roof of vehicle and only 10 cm tall. K/Ka-band antenna rugged and compact to suit rooftop mobile operating environment. More-delicate signal-processing and control equipment located inside vehicle.

19 CFR 11.12 - Labeling of wool products to indicate fiber content.

Code of Federal Regulations, 2013 CFR

2013-04-01

... more than 20 years prior to importation, and except carpets, rugs, mats, and upholsteries, shall have... by T.D. 72-262, 37 FR 20318, Sept. 29, 1972; T.D. 73-175, 38 FR 17446, July 2, 1973; T.D. 84-213, 49...

19 CFR 11.12 - Labeling of wool products to indicate fiber content.

Code of Federal Regulations, 2011 CFR

2011-04-01

... more than 20 years prior to importation, and except carpets, rugs, mats, and upholsteries, shall have... by T.D. 72-262, 37 FR 20318, Sept. 29, 1972; T.D. 73-175, 38 FR 17446, July 2, 1973; T.D. 84-213, 49...

19 CFR 11.12 - Labeling of wool products to indicate fiber content.

Code of Federal Regulations, 2014 CFR

2014-04-01

... more than 20 years prior to importation, and except carpets, rugs, mats, and upholsteries, shall have... by T.D. 72-262, 37 FR 20318, Sept. 29, 1972; T.D. 73-175, 38 FR 17446, July 2, 1973; T.D. 84-213, 49...

19 CFR 11.12 - Labeling of wool products to indicate fiber content.

Code of Federal Regulations, 2012 CFR

2012-04-01

... more than 20 years prior to importation, and except carpets, rugs, mats, and upholsteries, shall have... by T.D. 72-262, 37 FR 20318, Sept. 29, 1972; T.D. 73-175, 38 FR 17446, July 2, 1973; T.D. 84-213, 49...

Collection Development: Great Finds for Your Collectibles Shelf.

ERIC Educational Resources Information Center

Gross, Margarete

1993-01-01

Briefly reviews 41 books and periodicals about antiques and collectibles such as glassware, porcelain, dolls, buttons, ceramics, folk arts, furniture, jewelry, rugs, textiles, and woodenware. Books are arranged in the following topic areas: price guides; general surveys; out-of-print titles; trends; conservation and restoration; dealers; and…

The performance of NASA research hydrogen masers

NASA Technical Reports Server (NTRS)

Reinhardt, V. S.; Rueger, L. J.

1980-01-01

Field operable hydrogen masers based on prior maser designs are presented. These units incorporate improvements in magnetic shielding, lower noise electronics, better thermal control, and have a microprocessor for operation, monitoring, and diagnostic functions. They are ruggedly built for transportability and ease of service anywhere in the world.

Mountain Biking: Does Rough Terrain Make Rugged Riders?

ERIC Educational Resources Information Center

Cinque, Chris

1987-01-01

No formal research has been conducted on the training effects and injury risks of all-terrain bicycles in mountain biking, but experience indicates they are apparently safe and may provide greater fitness benefits than traditional bicycles. The bicycles are described, and their apparent benefits are discussed. (MT)

75 FR 48669 - Product Cancellation Order for Certain Pesticide Registrations

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-11

... Shampoo for Dogs 002517-00055 Sergeant's Rug Piperonyl butoxide Patrol Carpet Insecticide and Freshener... Residual Pyrethrins Flea and Tick Permethrin Spray for Dogs and Cats 004822-00461 Whitmire Residual...-00011 Ear-Rite Piperonyl butoxide Insecticidal Ear Pyrethrins Wash for Dogs 010772-00016 Lambert Kay...

Strategic plan for coordinating rural intelligent transportation system (ITS) transit development in the Great Smoky Mountains National Park

DOT National Transportation Integrated Search

2002-11-01

The Great Smoky Mountains National Park, located along the border between North Carolina and Tennessee, is the most visited national park in the United States. This rugged, mountainous area presents many transportation challenges. The immense popular...

Recovery of precious metals from space

NASA Technical Reports Server (NTRS)

Freiser, Henry

1991-01-01

The overall objective is to develop efficient and economical separation and recovery methods for the platinum group and other precious metals. The separation of Pd(II) from Pt(II), Ir(III), and Rh(III) with trioctylphosphine oxide (TOPO) in heptane using centrifugal partition chromatography (CPC) was investigated. Activities to achieve this objective focussed on selection and evaluation of extraction systems for the PGM and modification of selected systems for multistage operation with a view to scaling up to desired macro levels. On the basis of preliminary evaluation of a series of simple metal complexing agents and chelating agents, the TOPO in heptane was selected as a likely system for isolating of Pd(II) and Pt(II) from the other PGM. A multistage apparatus capable of configuration as a simple rugged device, a centrifugal partition chromatograph (CPC), was shown to be effective. The extraction of Pd(II) was studied by CPC and batch solvent extraction. The distribution ratios for Pd(II) determined by both methods agree well. In low HCl concentrations (less than 0.1 M), the extracted species was PdCl2.(TOPO)2, irrespective of the chloride concentration, while at acid concentrations above 0.1 M, the Pd was extracted as the ion pair, 2(TOPO.H+).(PdCl4)2-. Base line separation of Pd(II) and Pt(II) in CPC was obtained under a variety of chloride and HCl concentration. It was demonstrated that the efficiency of CPC for metal separation was limited by chemical kinetic factors rather than instrumental factors, strongly suggesting that dramatic improvements can be achieved by studying reaction kinetics of formation and dissociation of the extractable metal complex.

Development and in-house validation of a rapid and simple to use ELISA for the detection and measurement of the mycotoxin sterigmatocystin.

PubMed

Oplatowska-Stachowiak, Michalina; Reiring, Claudine; Sajic, Nermin; Haasnoot, Willem; Brabet, Catherine; Campbell, Katrina; Elliott, Christopher T; Salden, Martin

2018-05-01

Sterigmatocystin (STG) is a highly toxic secondary fungal metabolite structurally closely related to the well-known carcinogenic aflatoxins. Its presence has been reported in grains and grain-based products as well as in other foodstuffs like nuts, green coffee beans, spices, beer and cheese. Due to the lack of suitable data on the occurrence of STG, in 2013, the European Food Safety Authority (EFSA) could not characterise its risk for human health and recommended that more data on STG in food and feed needed to be collected. In order to provide a new tool for the specific detection of STG, a competitive enzyme-linked immunosorbent assay (ELISA) was developed, optimised and validated in this study based on a sensitive monoclonal antibody specific to STG with no cross-reactivity with aflatoxins. The sample preparation method for rice, wheat and maize was based on a modified QuEChERS (quick, easy, cheap, effective, rugged and safe) approach. The assay was validated for the detection of STG in rice, wheat and maize in accordance with the guidelines for validation of semi-quantitative screening methods included in Commission Regulation (EU) 519/2014. The screening target concentration (STC) was set at 1.5 μg/kg. The cutoffs for rice, wheat and maize were 1.2, 1.2 and 1.3 μg/kg and the false suspected rates were 0.34, 1.15 and 0.78%, respectively. Good correlation was found between the results obtained by the STG ELISA and LC-MS/MS method for naturally contaminated rice samples. This validated method can be applied as a sensitive and high-throughput screening for the presence of STG in a range of agricultural commodities. Graphical abstract A new enzyme-linked immunosorbent assay based on an antibody specific to sterigmatocystin for the detection of this mycotoxin in corn, wheat and rice.

Recent developments in OLED-based chemical and biological sensors

NASA Astrophysics Data System (ADS)

Shinar, Joseph; Zhou, Zhaoqun; Cai, Yuankun; Shinar, Ruth

2007-09-01

Recent developments in the structurally integrated OLED-based platform of luminescent chemical and biological sensors are reviewed. In this platform, an array of OLED pixels, which is structurally integrated with the sensing elements, is used as the photoluminescence (PL) excitation source. The structural integration is achieved by fabricating the OLED array and the sensing element on opposite sides of a common glass substrate or on two glass substrates that are attached back-to-back. As it does not require optical fibers, lens, or mirrors, it results in a uniquely simple, low-cost, and potentially rugged geometry. The recent developments on this platform include the following: (1) Enhancing the performance of gas-phase and dissolved oxygen sensors. This is achieved by (a) incorporating high-dielectric TiO II nanoparticles in the oxygen-sensitive Pt and Pd octaethylporphyrin (PtOEP and PdOEP, respectively)- doped polystyrene (PS) sensor films, and (b) embedding the oxygen-sensitive dyes in a matrix of polymer blends such as PS:polydimethylsiloxane (PDMS). (2) Developing sensor arrays for simultaneous detection of multiple serum analytes, including oxygen, glucose, lactate, and alcohol. The sensing element for each analyte consists of a PtOEP-doped PS oxygen sensor, and a solution containing the oxidase enzyme specific to the analyte. Each sensing element is coupled to two individually addressable OLED pixels and a Si photodiode photodetector (PD). (3) Enhancing the integration of the platform, whereby a PD array is also structurally integrated with the OLED array and sensing elements. This enhanced integration is achieved by fabricating an array of amorphous or nanocrystalline Si-based PDs, followed by fabrication of the OLED pixels in the gaps between these Si PDs.

Distributed energy-balance modeling of snow-cover evolution and melt in rugged terrain: Tobacco Root Mountains, Montana, USA

USGS Publications Warehouse

Letsinger, S.L.; Olyphant, G.A.

2007-01-01

A distributed energy-balance model was developed for simulating snowpack evolution and melt in rugged terrain. The model, which was applied to a 43-km2 watershed in the Tobacco Root Mountains, Montana, USA, used measured ambient data from nearby weather stations to drive energy-balance calculations and to constrain the model of Liston and Sturm [Liston, G.E., Sturm, M., 1998. A snow-transport model for complex terrain. Journal of Glaciology 44 (148), 498-516] for calculating the initial snowpack thickness. Simulated initial snow-water equivalent ranged between 1 cm and 385 cm w.e. (water equivalent) with high values concentrated on east-facing slopes below tall summits. An interpreted satellite image of the snowcover distribution on May 6, 1998, closely matched the simulated distribution with the greatest discrepancy occurring in the floor of the main trunk valley. Model simulations indicated that snowmelt commenced early in the melt season, but rapid meltout of snow cover did not occur until after the average energy balance of the entire watershed became positive about 45 days into the melt season. Meltout was fastest in the lower part of the watershed where warmer temperatures and tree cover enhanced the energy income of the underlying snow. An interpreted satellite image of the snowcover distribution on July 9, 1998 compared favorably with the simulated distribution, and melt curves for modeled canopy-covered cells mimicked the trends measured at nearby snow pillow stations. By the end of the simulation period (August 3), 28% of the watershed remained snow covered, most of which was concentrated in the highest parts of the watershed where initially thick accumulations had been shaded by surrounding summits. The results of this study provide further demonstration of the critical role that topography plays in the timing and magnitude of snowmelt from high mountain watersheds. ?? 2006 Elsevier B.V. All rights reserved.

Development of advanced diagnostics for characterization of burning droplets in microgravity

NASA Technical Reports Server (NTRS)

Sankar, Subramanian; Buermann, Dale H.; Bachalo, William D.

1995-01-01

Diagnostic techniques currently used for microgravity research are generally not as advanced as those used in earth based gravity experiments. Diagnostic techniques for measuring the instantaneous radial temperature profile (or temperature gradients) within the burning droplet do not exist. Over the past few years, Aerometrics has been researching and developing a rainbow thermometric technique for measuring the droplet temperatures of burning droplets. This technique has recently been integrated with the phase Doppler interferometric technique to yield a diagnostic instrument that can be used to simultaneously measure the size, velocity, and temperature of burning droplets in complex spray flames. Also, the rainbow thermometric technique has been recently integrated with a point-diffraction interferometric technique for measuring the instantaneous gas phase temperature field surrounding a burning droplet. These research programs, apart from being very successful, have also helped us identify other innovative techniques for the characterization of burning droplets. For example, new techniques have been identified for measuring the instantaneous regression rate of burning droplets. Also, there is the possibility of extracting the instantaneous radial temperature distribution or the temperature gradients within a droplet during transient heating. What is important is that these diagnostic techniques have the potential for making use of inexpensive, light-weight, and rugged devices such as diode lasers and linear CCD arrays. As a result, they can be easily packaged for incorporation into microgravity drop-test and flight-test facilities. Furthermore, with the use of linear CCD arrays, data rates as high as 10-100 kHz can be easily achieved. This data rate is orders of magnitude higher than what is currently achievable. In this research and development program, a compact and rugged diagnostic system will be developed that can be used to measure instantaneous fuel droplet diameter, droplet regression rate, and the droplet internal temperature profiles or gradients at very high data rates in microgravity experiments.

Report: Comparison of qualitative, quantitative analysis and antioxidant potential between wild and cultivated Borago officinalis leaves from palestine.

PubMed

Abu-Qaoud, Hassan; Shawarb, Nuha; Hussen, Fatima; Jaradat, Nidal; Shtaya, Munqez

2018-05-01

Borago officinalis plant is an important plant of high medicinal and nutritional values. This study designed to evaluate antioxidant activity, screen the existence of phytogenic chemical compounds and to determine the total flavonoid and phenol contents of wild and cultivated Borago officinalis. Total flavonoid contents of the wild and cultivated Borago officinalis were determined by using rutin reference standard method and total phenols determined by using Folin Ciocalteu's method while antioxidant activity evaluated by using 2, 2-diphenyl-1-picryl-hydrazyl-hydrate assay. Phytochemical analyses indicated the presence of carbohydrate, phenols, flavonoids, phytosteroids tannins and volatile oil. The total flavonoid content of the methanolic extract from the wild borage plant was 22.4mg RU/g this value was reduced to 13.1mg RU/g for the cultivated methanolic extract as well as the total phenols contents was dropped from 5.21mg GA/g to 2.37mg GA/g methanolic extracts. Total tannins content of the wild growing borage plant was 13.7mg GA/g methanolic extract. This value was higher in the cultivated borage with 21.33mg GA/g methanolic extract. The wild leaves extract had IC 50 =6.3μg/mL for wild leaves extract was closer to IC 50 value of Trolox (standard reference with high antioxidant activity), while the cultivated leaves extract had higher IC 50 = 8.7μg/mL which mean lower antioxidant activity than the wild growing one. The data of this study showed that the extracts of Borago officinalis possess antioxidant and free radical scavenging activities. Variation was clear between wild and cultivated species, these findings propose that such plant extract could have a wide range of applications in both food and pharmaceutical industries. Therefore, more research is necessary to investigate different cultural practices on the efficiency of borage plant.

75 FR 60277 - National Hunting and Fishing Day, 2010

Federal Register 2010, 2011, 2012, 2013, 2014

2010-09-29

... Part VII The President Proclamation 8567--National Hunting and Fishing Day, 2010 Proclamation 8568--National Public Lands Day, 2010 Proclamation 8569--Gold Star Mother's and Families' Day, 2010 #0; #0; #0... into the character of our Nation. From the rocky shoals of New England to the rugged mountains of the...

The Chameleon on a Tartan Rug: Adaptations of Three Academic Developers' Professional Identities

ERIC Educational Resources Information Center

Kensington-Miller, Barbara; Renc-Roe, Joanna; Morón-García, Susan

2015-01-01

This paper builds on discussions of academic developers' identity experienced as a discomfiting, troubled, and often marginal space. Three experienced academic developers, located in research-intensive institutions in three different countries, using auto-ethnographic writing and a shared narrative inquiry, explore moments of congruence and…

Behavioral System Feedback Measurement Failure: Sweeping Quality under the Rug

ERIC Educational Resources Information Center

Mihalic, Maria T.; Ludwig, Timothy D.

2009-01-01

Behavioral Systems rely on valid measurement systems to manage processes and feedback and to deliver contingencies. An examination of measurement system components designed to track customer service quality of furniture delivery drivers revealed the measurement system failed to capture information it was designed to measure. A reason for this…

SOLAR PHOTOVOLTAIC SYSTEM DESIGN FOR A REMOTE COMMUNITY IN PANAMA

EPA Science Inventory

Santo Domingo, Panama, is a rural town of 100, located in the Colon province within Chagres National Park. The town’s inhabitants are small-scale farmers and ranchers. The town is only accessible via rugged roads and has neither electric nor phone lines. Since the town i...

46 CFR 72.05-55 - Furniture and furnishings.

Code of Federal Regulations, 2010 CFR

2010-10-01

... shall be of approved fire resistant fabrics. (4) All rugs and carpets shall be of wool or other material... subpart, rooms containing “fire resistant furnishings” will be considered to be those in which: (1) All... fire resistant furnishings. In addition, all upholstery and padding of chairs, sofas, etc., in these...

Wireless IR Image Transfer System for Autonomous Vehicles

DTIC Science & Technology

2003-12-01

the camera can operate between 0 and 500 C; this uniquely suites it for employment on autonomous vehicles in rugged environments. The camera is...system is suitable for used on autonomous vehicles under varying antenna orientations. • The third is the use of MDS transceivers allows the received

78 FR 60177 - National Public Lands Day, 2013

Federal Register 2010, 2011, 2012, 2013, 2014

2013-10-01

... diverse and rugged landscapes reflect our national character, the way we care for these open spaces.... Since I established this initiative, we have expanded access to recreation, restored critical landscapes, and created urban parks and water trails. We are also working with partners to let young people serve...

Women of California.

ERIC Educational Resources Information Center

Gray, Harry

This publication points out the achievements of women who contributed to the development and history of California from the 16th century, when the Spanish Conquistadores moved westward into the San Francisco Bay area, to the gold rush of 1848, and during the following period when women helped stabilize society on the rugged frontier. Women not…

The Effects of Soviet Army Communications Jamming on the AIM Division Signal Battalion.

DTIC Science & Technology

1980-06-06

Mass ". Antenna Antenn Figure 2-16 This explains why tactical line-of-site communication systems have installation difficulties when deployed in rugged...vertically polarized loop and adcock type antennas. While these antennas are especially reliable when identifing the azimuth of vertically polarized signal

Single-Domain Antibodies: Rugged Recognition Element

DTIC Science & Technology

2007-01-01

and spiny dogfish shark (60 million representatives), which are displayed on filamentous phage M13 . We selected the llama- derived library for binding...subject to a penalty for failing to comply with a collection of information if it does not display a currently valid OMB control number. 1. REPORT DATE

Choral Counting

ERIC Educational Resources Information Center

Turrou, Angela Chan; Franke, Megan L.; Johnson, Nicholas

2017-01-01

The students in Ms. Moscoso's second-grade class gather on the rug after recess, ready for one of their favorite math warm-ups: Choral Counting. Counting is an important part of doing mathematics throughout the school; students count collections (Schwerdtfeger and Chan 2007) and solve problems using a variety of strategies, many of which are…

Multiresidue analysis of pesticides in straw roughage by liquid chromatography - tandem mass spectrometry

USDA-ARS?s Scientific Manuscript database

A multiresidue analytical method using a modification of the “quick, easy, cheap, effective, rugged, and safe” (QuEChERS) sample preparation approach combined with liquid chromatography–tandem mass spectrometry (LC-MS/MS) analysis was established and validated for the rapid determination of 69 pesti...

City Slickers: Let the Cattle Speak for Themselves

ERIC Educational Resources Information Center

Woodcock, Ray

2006-01-01

"City Slickers", the classic movie starring Billy Crystal, portrays a man who rediscovers a part of himself during a two-week cattle drive adventure in the rugged American West. His rediscovery arises from the challenge itself, with minimal psychologically oriented discussion or "processing." The belief that such a thing can…

16 CFR 1630.31 - Reasonable and representative tests and recordkeeping requirements.

Code of Federal Regulations, 2012 CFR

2012-01-01

..., constructional units (needles, pitch, rows, shot, stitches, and weight), dye class, dyestuff, dyeing application... representative tests with respect to any quality of machine-made carpets or rugs are (1) at least one test performed upon commencement of production, importation, or other receipt thereof, (2) at least one test...

16 CFR 1630.31 - Reasonable and representative tests and recordkeeping requirements.

Code of Federal Regulations, 2014 CFR

2014-01-01

..., constructional units (needles, pitch, rows, shot, stitches, and weight), dye class, dyestuff, dyeing application... representative tests with respect to any quality of machine-made carpets or rugs are (1) at least one test performed upon commencement of production, importation, or other receipt thereof, (2) at least one test...

16 CFR 1630.31 - Reasonable and representative tests and recordkeeping requirements.

Code of Federal Regulations, 2011 CFR

2011-01-01

..., constructional units (needles, pitch, rows, shot, stitches, and weight), dye class, dyestuff, dyeing application... representative tests with respect to any quality of machine-made carpets or rugs are (1) at least one test performed upon commencement of production, importation, or other receipt thereof, (2) at least one test...

16 CFR 1631.31 - Reasonable and representative tests and recordkeeping requirements.

Code of Federal Regulations, 2014 CFR

2014-01-01

..., constructional units (needles, pitch, rows, shot, stitches, and weight), dye class, dyestuff, dyeing application... representative tests with respect to any quality of machine-made carpets or rugs are (1) at least one test performed upon commencement of production, importation, or other receipt thereof, (2) at least one test...

16 CFR 1630.31 - Reasonable and representative tests and recordkeeping requirements.

Code of Federal Regulations, 2010 CFR

2010-01-01

..., constructional units (needles, pitch, rows, shot, stitches, and weight), dye class, dyestuff, dyeing application... representative tests with respect to any quality of machine-made carpets or rugs are (1) at least one test performed upon commencement of production, importation, or other receipt thereof, (2) at least one test...

16 CFR 1631.31 - Reasonable and representative tests and recordkeeping requirements.

Code of Federal Regulations, 2011 CFR

2011-01-01

..., constructional units (needles, pitch, rows, shot, stitches, and weight), dye class, dyestuff, dyeing application... representative tests with respect to any quality of machine-made carpets or rugs are (1) at least one test performed upon commencement of production, importation, or other receipt thereof, (2) at least one test...

16 CFR 1631.31 - Reasonable and representative tests and recordkeeping requirements.

Code of Federal Regulations, 2010 CFR

2010-01-01

..., constructional units (needles, pitch, rows, shot, stitches, and weight), dye class, dyestuff, dyeing application... representative tests with respect to any quality of machine-made carpets or rugs are (1) at least one test performed upon commencement of production, importation, or other receipt thereof, (2) at least one test...

16 CFR 1631.31 - Reasonable and representative tests and recordkeeping requirements.

Code of Federal Regulations, 2012 CFR

2012-01-01

..., constructional units (needles, pitch, rows, shot, stitches, and weight), dye class, dyestuff, dyeing application... representative tests with respect to any quality of machine-made carpets or rugs are (1) at least one test performed upon commencement of production, importation, or other receipt thereof, (2) at least one test...

CTEPP NC DATA COLLECTED ON FORM 04: PARENT PRE-MONITORING QUESTIONNAIRE

EPA Science Inventory

This data set contains data concerning the individuals living in the home and the possible sources and routes of exposure, and the activity patterns of the preschool children. The parent was asked questions related to the age of their home; frequency of cleaning carpets, rugs, an...

Low frequency full waveform seismic inversion within a tree based Bayesian framework

NASA Astrophysics Data System (ADS)

Ray, Anandaroop; Kaplan, Sam; Washbourne, John; Albertin, Uwe

2018-01-01

Limited illumination, insufficient offset, noisy data and poor starting models can pose challenges for seismic full waveform inversion. We present an application of a tree based Bayesian inversion scheme which attempts to mitigate these problems by accounting for data uncertainty while using a mildly informative prior about subsurface structure. We sample the resulting posterior model distribution of compressional velocity using a trans-dimensional (trans-D) or Reversible Jump Markov chain Monte Carlo method in the wavelet transform domain of velocity. This allows us to attain rapid convergence to a stationary distribution of posterior models while requiring a limited number of wavelet coefficients to define a sampled model. Two synthetic, low frequency, noisy data examples are provided. The first example is a simple reflection + transmission inverse problem, and the second uses a scaled version of the Marmousi velocity model, dominated by reflections. Both examples are initially started from a semi-infinite half-space with incorrect background velocity. We find that the trans-D tree based approach together with parallel tempering for navigating rugged likelihood (i.e. misfit) topography provides a promising, easily generalized method for solving large-scale geophysical inverse problems which are difficult to optimize, but where the true model contains a hierarchy of features at multiple scales.

Recent progress in MEMS technology development for military applications

NASA Astrophysics Data System (ADS)

Ruffin, Paul B.; Burgett, Sherrie J.

2001-08-01

The recent progress of ongoing efforts at the Army Aviation and Missile Command (AMCOM) to develop microelectromechanical systems (MEMS) technology for military applications is discussed in this paper. The current maturity level of low cost, low power, micro devices in industry, which range from simple temperature and pressure sensors to accelerometers in airbags, provides a viable foundation for the development of rugged MEMS devices for dual-use applications. Early MEMS technology development efforts at AMCOM emphasized inertial MEMS sensors. An Army Science and Technology Objective (STO) project was initiated to develop low cost inertial components with moderate angular rate sensor resolution for measuring pitch and yaw of missile attitude and rotational roll rate. Leveraging the Defense Advanced Research Projects Agency and other Government agencies has resulted in the development of breadboard inertial MEMS devices with improved robustness. During the past two years, MEMS research at AMCOM has been expanded to include environmental MEMS sensors for missile health monitoring, RF-MEMS, optical MEMS devices for beam steering, and micro-optic 'benches' for opto-electronics miniaturization. Additionally, MEMS packaging and integration issues have come into focus and are being addressed. Selected ongoing research efforts in these areas are presented, and some horizon MEMS sensors requirements for Army and law enforcement are presented for consideration.

Bioequivalance and pharmacokinetic study of febuxostat in human plasma by using LC-MS/MS with liquid liquid extraction method.

PubMed

Chandu, Babu Rao; Kanala, Kanchanamala; Hwisa, Nagiat T; Katakam, Prakash; Khagga, Mukkanti

2013-12-01

A bioequivalence study was proved of generic Febuxostat 80 mg tablets (T) in healthy volunteers.For this purpose, Authors developed a simple, sensitive, selective, rapid, rugged and reproducible liquid chromatography-tandem mass spectrometry method for the quantification of Febuxostat (FB) in human plasma using Febuxostat D7 (FBD7) as an internal standard (IS) was used. Chromatographic separation was performed on Ascentis Express C18 (50x4.6 mm, 3.5 μ) column. Mobile phase composed of 10 mM Ammonium formate: Acetonitrile (20:80 v/v), with 0.8 mL/min flow-rate. Drug and IS were extracted by Liquid- liquid extraction. FB and FBD7 were detected with proton adducts at m/z 317.1→261.1 and 324.2→262.1 in multiple reaction monitoring (MRM) positive mode respectively. The method was validated with the correlation coefficients of (r(2)) ≥ 0.9850 over a linear concentration range of 1.00-8000.00 ng/mL. This method demonstrated intra and inter-day precision within 2.64 to 3.88 and 2.76 to 8.44% and accuracy within 97.33 to 99.05 and 100.30 to 103.19% for FB. This method is successfully applied in the Bioequivalence study of 9 human volunteers.

Active matrix OLED for rugged HMD and viewfinder applications

NASA Astrophysics Data System (ADS)

Low, Kia; Jones, Susan K.; Prache, Olivier; Fellowes, David A.

2004-09-01

We present characterization of a full-color 852x3x600-pixel, active matrix organic light emitting diode (AMOLED) color microdisplay (eMagin Corporation's SVGA+ display) for environmentally demanding applications. The results show that the AMOLED microdisplay can provide cold-start turn-on and operate at extreme temperature conditions, far in excess of non-emissive displays. Correction factors for gamma response of the AMOLED microdisplay as a function of temperature have been determined to permit consistent luminance and contrast from -40°C to over +80°C. Gamma adjustments are made by a simple temperature compensation adjustment of the reference voltages of the AMOLED. The typical room temperature full-on luminance half-life of the SVGA+ full color display organic light emitting diode (OLED) display at over 3,000 hr at a starting luminance at approx. 100 cd/m2, translates to more than 15,000 hr of continuous full-motion video usage, based on a 25% duty cycle at a typical 50-60 cd/m2 commercial luminance level, or over 60,000 hr half-life in monochrome white usage, or over 100,000 hr luminance half-life in monochrome yellow usage at similar operating conditions. Half life at typical night vision luminance levels would be much longer.

[Simultaneous determination of 6 neonicotinoid residues in soil using DLLME-HPLC and UV].

PubMed

Sun, Bao-li; Shan, Hong; Li, Yan-hua; Zeng, Ya-ling; Shen, Xiu-li; Tong, Cheng-feng

2013-09-01

A simple, cheap and rugged method was developed for simultaneous deter mination of 6 neonicotinoid residues in soil, including imidacloprid, acetamiprid, thiamethoxam, thiacloprid, clothianidin and nitenpyram. The soil sample was produced by dispersive liquid-liquid micro-extraction (DLLME) after extracted by the mixed solution of acetonitrile and CH2Cl2 (2:1, phi). The analytes were separated by HPLC with Alltima C18 column (4.6 mm x 250 mm, 5 microm) and detected by PDA at 260 nm. External standard method was used for quantification. The results showed that good linearity was obtained with correlation coefficients between 0.9982 and 0.9999 in the range of 0.5-200 microg x L(-1). The limits of detection (LODs) were in the range between 0.0005 and 0.003 microg x mL(-1) (S/N = 3). The method was validated with five soil samples spiked at three fortification levels (0.05, 0.1, 1.0 mg x kg(-1)) and recoveries were in the range of 55.3%-95.6% with RSD of 1.4%-7.0%. The effect of clean-up was evaluated by UV spectra and demonstrated that the method established is effective. In conclusion, this method is competent for the simultaneous analysis of 6 neonicotinoid residues in soil.

Polysoaps: Configurations and Elasticity

NASA Astrophysics Data System (ADS)

Halperin, A.

1997-03-01

Simple polymers are very long, flexible, linear molecules. Amphiphiles, soaps, are small molecules comprising of a part that prefers water over oil and a part that prefers oil over water. By combining the two we arrive at an interesting, little explored, class of materials: Polysoaps. These comprise of a water soluble backbone incorporating, at intervals, covalently bound amphiphilic monomers. In water, the polymerised amphiphiles aggregate into self assembled units known as micelles. This induces a dramatic modification of the spatial configurations of the polymers. What were featureless random coils now exhibit intramolecular, hierachial self organisation. Due to this self organisation it is necessary to modify the paradigms describing the large scale behaviour of these polymers: Their configurations, dimensions and elasticity. Understanding the behaviour of these polymers is of practical interest because of their wide range of industrial applications, ranging from cosmetics to paper coating. It is of fundamental interest because polysoaps are characterised by a rugged free energy landscape that is reminiscent of complex systems such as proteins and glasses. The talk concerns theoretical arguments regarding the following issues: (i) The design parameters that govern the spatial configurations of the polysoaps, (ii) The interaction between polysoaps and free amphiphiles, (iii) The effect of the intramolecular self organisation on the elasticity of the chains.

Challenges in Modelling and Control of Offshore De-oiling Hydrocyclone Systems

NASA Astrophysics Data System (ADS)

Durdevic, Petar; Pedersen, Simon; Yang, Zhenyu

2017-01-01

Offshore de-oiling installations are facing an increasing challenge with regards to removing oil residuals from produced water prior to discharge into the ocean. The de-oiling of produced water is initially achieved in the primary separation processes using gravity-based multi-phase separators, which can effectively handle large amounts of oil-well fluids but may struggle with the efficient separation of small dispersed oil particles. Thereby hydrocyclone systems are commonly employed in the downstream Produced Water Treatment (PWT) process for further reducing the oil concentration in the produced water before it can be discharged into the ocean. The popularity of hydrocyclone technology in the offshore oil and gas industry is mainly due to its rugged design and low maintenance requirements. However, to operate and control this type of system in an efficient way is far less simple, and alternatively this task imposes a number of key control challenges. Specifically, there is much research to be performed in the direction of dynamic modelling and control of de-oiling hydrocyclone systems. The current solutions rely heavily on empirical trial-and-error approaches. This paper gives a brief review of current hydrocyclone control solutions and the remaining challenges and includes some of our recent work in this topic and ends with a motivation for future work.

Determination of tramadol hydrochloride in ampoule dosage forms by using UV spectrophotometric and HPLC-DAD methods in methanol and water media.

PubMed

Küçük, Aysel; Kadioğlu, Yücel

2005-02-01

Two newly developed simple and sensitive methods for determination of tramadol hydrochloride in ampoule dosage forms were described and validated. Measurements for spectrophotometric method were performed using UV-Vis Spectrophotometer in ranges of 200-400 nm. The solutions of standard and the samples were prepared in methanol and water media and the UV absorption spectrums of tramadol were monitored with maximum absorptions at 275 and 271 nm for both mediums, respectively. The standard calibration curves of tramadol were constructed by plotting absorbance vs. concentration in the concentration range with the final dilution of 10-100 microg ml-1. Reversed phase chromatography for HPLC method was conducted using a Phenomenex Bondclone C18 column with an isocratic mobile phase consisting of 25% acetonitrile in 75% 0.01 M phosphate buffer (pH 3). The effluent was monitored on a DAD detector at 218 nm. Linear response (r>0.99) was observed over the range of 0.5-40 microg ml-1 for methanol and water and run on six different occasions. The methods were applied successfully to pharmaceutical ampoule forms, but also for comparison in two different solvent media. Besides, it was completely validated and proven to be rugged.

[Determination of fatty acid esters of chloropropanediols in diet samples by gas chromatography-mass spectrometry coupled with solid-supported liquid-liquid extraction].

PubMed

Gao, Jie; Liu, Qing; Han, Feng; Miao, Hong; Zhao, Yunfeng; Wu, Yongning

2014-05-01

To establish a method for the determination of fatty acid esters of 3-monochloropropane-1, 2-diol (3-MCPD) and 2-monochloropropane-1, 3-diol (2-MCPD) in diet samples by gas chromatography-mass spectrometry (GC-MS) with solid-supported liquid-liquid extraction (SLE). Diet samples were ultrasonically extracted by hexane, followed by ester cleavage reaction with sodium methylate in methanol, and then purified by solid-supported liquid-liquid extraction. (SLE) using diatomaceous earth as the sorbent. After derivatization with heptafluorobutyrylimidazole, the analytes were detected by GC-MS and quantified by the deuterated internal standards. The limits of detection (LODs) of 3-MCPD esters and 2-MCPD esters in different diet samples were 0.002 - 0.005 mg/kg and 0.002 - 0.006 mg/kg. The average recoveries of 3-MCPD esters and 2-MCPD esters at the spiking levels of 0.05 and 0.1 mg/kg in the diet samples were in the range of 65.9% - 104.2% and 75.4% - 118.0%, respectively, with the relative standard deviations in the range of 2.2% - 14.2% and 0.8% - .13.9%. The method is simple, accurate and rugged for the determination of fatty acid esters of 3-MCPD and 2-MCPD in diet samples.

Simple and sensitive monitoring of β2-agonist residues in meat by liquid chromatography-tandem mass spectrometry using a QuEChERS with preconcentration as the sample treatment.

PubMed

Xiong, Lin; Gao, Ya-Qin; Li, Wei-Hong; Yang, Xiao-Lin; Shimo, Shimo Peter

2015-07-01

A liquid chromatography with tandem mass spectrometric detection (LC-MS/MS) method was established for the simultaneous determination of the levels of 10 β2-agonists in meat. The samples were extracted using an aqueous acidic solution and cleaned up using a Quick, Easy, Cheap, Effective, Rugged and Safe (QuEChERS) technique utilising a DVB-NVP-SO3Na sorbent synthesised in-house. First, the β2-agonist residues were extracted in an aqueous acidic solution, followed by matrix solid-phase dispersion for clean-up. The linearities of the method were R(2)=0.9925-0.9998, with RSDs of 2.7-15.3% and 73.7-103.5% recoveries. Very low limits of detection (LOD) and quantitation (LOQ) of 0.2-0.9 μg/kg and 0.8-3.2 μg/kg, respectively, were achieved for spiked meat. The values obtained were lower than the maximum residue limits (MRLs) established by the EU and China. These results clearly demonstrate the feasibility of the proposed approach. The evaluated method provided reliable screening, quantification and identification of 10 β2-agonists in meat. Copyright © 2015 Elsevier Ltd. All rights reserved.

Space shuttle main engine controller

NASA Technical Reports Server (NTRS)

Mattox, R. M.; White, J. B.

1981-01-01

A technical description of the space shuttle main engine controller, which provides engine checkout prior to launch, engine control and monitoring during launch, and engine safety and monitoring in orbit, is presented. Each of the major controller subassemblies, the central processing unit, the computer interface electronics, the input electronics, the output electronics, and the power supplies are described and discussed in detail along with engine and orbiter interfaces and operational requirements. The controller represents a unique application of digital concepts, techniques, and technology in monitoring, managing, and controlling a high performance rocket engine propulsion system. The operational requirements placed on the controller, the extremely harsh operating environment to which it is exposed, and the reliability demanded, result in the most complex and rugged digital system ever designed, fabricated, and flown.

A sensitive, handheld vapor sensor based on microcantilevers

NASA Astrophysics Data System (ADS)

Pinnaduwage, L. A.; Hedden, D. L.; Gehl, A.; Boiadjiev, V. I.; Hawk, J. E.; Farahi, R. H.; Thundat, T.; Houser, E. J.; Stepnowski, S.; McGill, R. A.; Deel, L.; Lareau, R. T.

2004-11-01

We report the development of a handheld sensor based on piezoresistive microcantilevers that does not depend on optical detection, yet has high detection sensitivity. The sensor is able to detect vapors from the plastic explosives pentaerythritol tetranitrate and hexahydro-1,3,5-triazine at levels below 10 parts per trillion within few seconds of exposure under ambient conditions. A differential measurement technique has yielded a rugged sensor that is unaffected by vibration and is able to function as a "sniffer." The microelectromechanical system sensor design allows for the incorporation of hundreds of microcantilevers with suitable coatings in order to achieve sufficient selectivity in the future, and thus could provide an inexpensive, unique platform for the detection of chemical, biological, and explosive materials.

A high power, pulsed, microwave amplifier for a synthetique aperture radar electrical model. Phase 1: Design

NASA Astrophysics Data System (ADS)

Atkinson, J. E.; Barker, G. G.; Feltham, S. J.; Gabrielson, S.; Lane, P. C.; Matthews, V. J.; Perring, D.; Randall, J. P.; Saunders, J. W.; Tuck, R. A.

1982-05-01

An electrical model klystron amplifier was designed. Its features include a gridded gun, a single stage depressed collector, a rare earth permanent magnet focusing system, an input loop, six rugged tuners and a coaxial line output section incorporating a coaxial-to-waveguide transducer and a pillbox window. At each stage of the design, the thermal and mechanical aspects were investigated and optimized within the framework of the RF specification. Extensive use was made of data from the preliminary design study and from RF measurements on the breadboard model. In an additional study, a comprehensive draft tube specification has been produced. Great emphasis has been laid on a second additional study on space-qualified materials and processes.

Dynamics of internal models in game players

NASA Astrophysics Data System (ADS)

Taiji, Makoto; Ikegami, Takashi

1999-10-01

A new approach for the study of social games and communications is proposed. Games are simulated between cognitive players who build the opponent’s internal model and decide their next strategy from predictions based on the model. In this paper, internal models are constructed by the recurrent neural network (RNN), and the iterated prisoner’s dilemma game is performed. The RNN allows us to express the internal model in a geometrical shape. The complicated transients of actions are observed before the stable mutually defecting equilibrium is reached. During the transients, the model shape also becomes complicated and often experiences chaotic changes. These new chaotic dynamics of internal models reflect the dynamical and high-dimensional rugged landscape of the internal model space.

Coal thickness guage using RRAS techniques, parts 2 and 3

NASA Technical Reports Server (NTRS)

King, J. D.; Rollwitz, W. L.

1980-01-01

Electron magnetic resonance was investigated as a sensing technique for use in measuring the thickness of the layer of coal overlying the rock substrate. The goal is development of a thickness gauge which will be usable for control of mining machinery to maintain the coal thickness within selected bounds. A sensor must be noncontracting, have a measurement range of 6 inches or more, and an accuracy of 1/2 inch or better. The sensor should be insensitive to variations in spacing between the sensor and the surface, the response speed should be adequate to permit use on continuous mining equipment, and the device should be rugged and otherwise suited for operation under conditions of high vibration, moisture, and dust. Finally, the sensor measurement must not be adversely affected by the natural effects occurring in coal such as impurities, voids, cracks, layering, high moisture level, and other conditions that are likely to be encountered.

Matrix effects in pesticide multi-residue analysis by liquid chromatography-mass spectrometry.

PubMed

Kruve, Anneli; Künnapas, Allan; Herodes, Koit; Leito, Ivo

2008-04-11

Three sample preparation methods: Luke method (AOAC 985.22), QuEChERS (quick, easy, cheap, effective, rugged and safe) and matrix solid-phase dispersion (MSPD) were applied to different fruits and vegetables for analysis of 14 pesticide residues by high-performance liquid chromatography with electrospray ionization-mass spectrometry (HPLC/ESI/MS). Matrix effect, recovery and process efficiency of the sample preparation methods applied to different fruits and vegetables were compared. The Luke method was found to produce least matrix effect. On an average the best recoveries were obtained with the QuEChERS method. MSPD gave unsatisfactory recoveries for some basic pesticide residues. Comparison of matrix effects for different apple varieties showed high variability for some residues. It was demonstrated that the amount of co-extracting compounds that cause ionization suppression of aldicarb depends on the apple variety as well as on the sample preparation method employed.

The Micro Fourier Transform Interferometer (muFTIR) - A New Field Spectrometer for Acquisition of Infrared Data of Natural Surfaces

NASA Technical Reports Server (NTRS)

Hook, Simon J.

1995-01-01

A lightweight, rugged, high-spectral-resolution interferometer has been built by Designs and Prototypes based on a set of specifications provided by the Jet Propulsion Laboratory and Dr. J. W. Salisbury (Johns Hopkins University). The instrument, the micro Fourier Transform Interferometer (mFTIR), permits the acquisition of infrared spectra of natural surfaces. Such data can be used to validate low and high spectral resolution data acquired remotely from aircraft and spacecraft in the 3-5 mm and 8-14 mm atmospheric window. The instrument has a spectral resolutions of 6 wavenumbers, weighs 16 kg including batteries and computer, and can be operated easily by two people in the field. Laboratory analysis indicates the instrument is spectrally calibrated to better than 1 wavenumber and the radiometric accuracy is <0.5 K if the radiances from the blackbodies used for calibration bracket the radiance from the sample.

Compact and Rugged Transceiver for Coherent Doppler Wind Lidar Applications in Space

NASA Technical Reports Server (NTRS)

Kavaya, Michael J.; Koch, Grady J.; Yu, Jirong; Amzajerdian, Farzin; Singh, Upendra N.; Trieu, Bo C.; Modlin, Ed A.; Petros, Mulugeta; Bai, Yingxin; Reithmaier, Karl;

Integrated multispectral high-power laser platform for the defeat of heat-seeking missiles

NASA Astrophysics Data System (ADS)

Tadjikov, Boris; Tsekoun, Alexei; Lyakh, Arkadiy; Maulini, Richard; Barron, Rodolfo; Patel, C. Kumar N.

2011-06-01

Quantum cascade lasers are finding rapid acceptance in many defense and security applications. Our new multispectral laser platform providing watt-level outputs near 2.0 μm, 4.0 μm and 4.6 μm in continuous wave regime at room temperature. Individual lasers are spectrally beam combined into a single output beam with excellent quality. Our rugged, compact (11 × 10 × 6.5 inches), and highly reliable, air-cooled multispectral laser platform is already finding acceptance at system level. Our uncooled devices produce > 2W at 4.6 μm and >1.5W at 4.0 μm at room temperature, and maintain watt-level output at 67°C with real wallplug efficiencies >10%. Finally, all of our QCLs undergo 100-hour pre-delivery burn-in and pass shock, vibration, and temperature testing according to MIL-STD-810G.

A Fiber-Optic Probe Design for Combustion Chamber Flame Detection Applications-Design Criteria, Performance Specifications, and Fabrication Technique

NASA Technical Reports Server (NTRS)

Borg, Stephen E.; Harper, Samuel E.

2001-01-01

This paper documents the design and development of the fiber-optic probes utilized in the flame detection systems used in NASA Langley Research Center's 8-Foot High Temperature Tunnel (8-ft HTT). Two independent flame detection systems are utilized to monitor the presence and stability of the main-burner and pilot-level flames during facility operation. Due to the harsh environment within the combustor, the successful development of a rugged and efficient fiber-optic probe was a critical milestone in the development of these flame detection systems. The final optical probe design for the two flame detection systems resulted from research that was conducted in Langley's 7-in High Temperature Pilot Tunnel (7-in HTT). A detailed description of the manufacturing process behind the optical probes used in the 8-ft HTT is provided in Appendix A of this report.

Highly sensitive nanostructure SnO2 based gas sensor for environmental pollutants

NASA Astrophysics Data System (ADS)

Korgaokar, Sushil; Moradiya, Meet; Prajapati, Om; Thakkar, Pranav; Pala, Jay; Savaliya, Chirag; Parikh, Sachin; Markna, J. H.

2017-05-01

A major quantity of pollutants are produced from industries and vehicles in the form of gas. New approaches are needed to solve well-known environmental pollutants like CO, CO2, NO2, SOx. Therefore detection with effective gas sensors is a vital part of pollution prevention efforts. There is a need to develop fast, rapid, cost-effective, highly sensitive, low power, and non-intrusive rugged sensors that can be easily installed. In the present study, nanostructured SnO2 used as a sensitive material in the devices and synthesized using hydrothermal process. The detailed development of the fabrication of SnO2 nanostructures gas sensor is described, which shows the remarkable change in the sensing properties with varying particle size. Additionally, we have used X-ray diffraction, scanning electron microscopy (SEM) for characterization and carefully examined the relative parameters like response magnitude (sensitivity) and selectivity of SnO2 nano structures with different particle size.

Laser Velocimeter for Studies of Microgravity Combustion Flowfields

NASA Technical Reports Server (NTRS)

Varghese, P. L.; Jagodzinski, J.

2001-01-01

We are currently developing a velocimeter based on modulated filtered Rayleigh scattering (MFRS), utilizing diode lasers to make measurements in an unseeded gas or flame. MFRS is a novel variation of filtered Rayleigh scattering, utilizing modulation absorption spectroscopy to detect a strong absorption of a weak Rayleigh scattered signal. A rubidium (Rb) vapor filter is used to provide the relatively strong absorption and semiconductor diode lasers generate the relatively weak Rayleigh scattered signal. Alkali metal vapors have a high optical depth at modest vapor pressures, and their narrow linewidth is ideally suited for high-resolution velocimetry; the compact, rugged construction of diode lasers makes them ideally suited for microgravity experimentation. Molecular Rayleigh scattering of laser light simplifies flow measurements as it obviates the complications of flow-seeding. The MFRS velocimeter should offer an attractive alternative to comparable systems, providing a relatively inexpensive means of measuring velocity in unseeded flows and flames.

Up Here It's Different: Community Education in Rural East Donegal

ERIC Educational Resources Information Center

Slevin, Amanda

2009-01-01

The familiar advertising slogan, "Up here it's different," used to attract visitors to the rugged beauty of County Donegal, was correct in highlighting that things are different in Donegal, although not for the reasons one might connect with tourism. For many, Donegal evokes nostalgic images of old, rural Ireland such as close community…

Development of a 10 Ah, Prismatic, Lithium-Ion Cell for NASA/GSFC

NASA Technical Reports Server (NTRS)

Stein, Brian; Baker, John W.; George, Douglas S.; Isaacs, Nathan D.; Shah, Pinakin M.; Rao, Gopalakrishna M.; Day, John H. (Technical Monitor)

2001-01-01

MSA's 10 Ah Li-ion cell is a rugged design suitable for the stringent requirements of aerospace applications. Eighteen cells demonstrate consistent cycling performance over a wide range of rates and temperatures. The cell passes qualification requirements for vibration survivability technology improvements at MSA continue to enhance cell performance.

Compact, Rugged, and Low-Cost Wavelength-Versatile Burst Laser

DTIC Science & Technology

2015-04-20

rubber grommets. (Figure26) Performance Lasers Contract #: W911NF-13-C-0050 19 Figure 26– CAD model of case with grommets Another way to keep...populated with anodized parts. (Figure 37) Figure 37 – Multiple boards populated with anodized parts These boards were then fitted into the rubber mounted

Effects of temperature and purity of magnesium sulfate during extraction of pesticides residues using the QuEChERS method

USDA-ARS?s Scientific Manuscript database

Despite its many documented advantages, the QuEChERS (quick, easy, cheap, effective, rugged and safe) sample preparation approach has problems with a few unstable pesticides, partly due to the exothermic reaction generated by the use of anhydrous magnesium sulfate during extraction. These pesticide...

Biogeographic, cultural, and historical setting [Chapter 2

Treesearch

Hanna K. Olson; Don W. Fallon

2018-01-01

The Intermountain Adaptation Partnership (IAP) encompasses unique landscapes within the Intermountain Region of the U.S. Forest Service (USFS), from rugged mountains to deep canyons, from alpine snowfields to wild and scenic rivers (fig. 1.1). The area defined by the boundaries of the Intermountain Region contains both private and Federally owned lands, including 12...

46 CFR 72.05-25 - Doors, other than watertight.

Code of Federal Regulations, 2013 CFR

2013-10-01

... bulkheads required to be Class A-0 shall be of solid or hollow steel or equivalent metal construction... top of approved deck covering. Rugs, and carpets, shall not pass through doorways, but linoleum and... 1/2 inch door stop at the sides and top, except: (i) Double doors capable of independent operation...

46 CFR 72.05-25 - Doors, other than watertight.

Code of Federal Regulations, 2014 CFR

2014-10-01

... bulkheads required to be Class A-0 shall be of solid or hollow steel or equivalent metal construction... top of approved deck covering. Rugs, and carpets, shall not pass through doorways, but linoleum and... 1/2 inch door stop at the sides and top, except: (i) Double doors capable of independent operation...

46 CFR 72.05-25 - Doors, other than watertight.

Code of Federal Regulations, 2012 CFR

2012-10-01

... bulkheads required to be Class A-0 shall be of solid or hollow steel or equivalent metal construction... top of approved deck covering. Rugs, and carpets, shall not pass through doorways, but linoleum and... 1/2 inch door stop at the sides and top, except: (i) Double doors capable of independent operation...

16 CFR 1631.4 - Test procedure.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 16 Commercial Practices 2 2012-01-01 2012-01-01 false Test procedure. 1631.4 Section 1631.4... SURFACE FLAMMABILITY OF SMALL CARPETS AND RUGS (FF 2-70) The Standard § 1631.4 Test procedure. (a) Apparatus—(1) Test chamber. The test chamber shall consist of an open top hollow cube made of noncombustible...

16 CFR 1630.4 - Test procedure.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 16 Commercial Practices 2 2012-01-01 2012-01-01 false Test procedure. 1630.4 Section 1630.4... SURFACE FLAMMABILITY OF CARPETS AND RUGS (FF 1-70) The Standard § 1630.4 Test procedure. (a) Apparatus—(1) Test chamber. The test chamber shall consist of an open top hollow cube made of noncombustible material...

Flow Meter

NASA Technical Reports Server (NTRS)

1990-01-01

Hedland Flow Meters manufactures a complete line of flow meters used in industrial operations to monitor the flow of oil, water or other liquids, air and other compressed gases, including caustics or corrosive liquids/gases. The company produces more than 1,000 types of flow meters featuring rugged construction, simplicity of installation and the ability to operate in any position.

War in Shangri-La: The Information Dimension of Nepal’s Maoist Insurgency and Counterinsurgency

DTIC Science & Technology

2005-09-01

part of the counterinsurgent. Most people, if they have any impression of Nepal at all, probably imagine it to be a land of rugged natural beauty ...that the RNA’s Directorate of Public Relations actively blocks web sites, closes discussion forums, monitors personal e-mail, and threatens bloggers

CTEPP DATA COLLECTION FORM 05: CHILD DAY CARE CENTER PRE-MONITORING QUESTIONNAIRE

EPA Science Inventory

This data collection form is used to identify the potential sources of pollutants at the day care center. The day care teacher is asked questions related to the age of their day care building; age and frequency of cleaning carpets or rugs; types of heating and air conditioning de...

Socio-Scientific Issues in Health Contexts: Treading a Rugged Terrain

ERIC Educational Resources Information Center

Lee, Yeung Chung

2012-01-01

The science-technology-society agenda has evolved over time to meet emerging educational aims in the light of changes in society and the environment. There is increasing emphasis on students' decision-making on socio-scientific issues (SSIs) not only to highlight the intricate relationships between science, technology, society, and the…

Master Plan

ERIC Educational Resources Information Center

Johnston, Robert C.

2005-01-01

During a volunteer stint on a hydroelectric-power project in the mountains of Honduras in 1996, William DeJong began "the walk." As the president of DeJong Inc., one of the top school facility planners in the United States, he wanted to study the conditions of schools in the rugged Central American countryside far from his home in…

A Report on Deliverable Four: Develop a specifications list for a portable, lightweight prehospital suction device

DTIC Science & Technology

reflect it. There are commercially available manual and powered suction devices on the market , and several are specifically advertised for use in...combine to suggest that no device on the market meets even the most basic requirements of being small, lightweight, rugged, and demonstrating adequate

A Report on Deliverable Six: Develop a Concept Design for a Ruggedized, Lightweight, Portable, Powered Handheld Suction Device

DTIC Science & Technology

reflect it. There are commercially available manual and powered suction devices on the market , and several are specifically advertised for use in...combine to suggest that no device on the market meets even the most basic requirements of being small, lightweight, rugged, and demonstrating adequate

77 FR 21936 - Endangered and Threatened Wildlife and Plants; Listing 23 Species on Oahu as Endangered and...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-12

... protection from adverse modification or destruction of critical habitat. In practice, situations with a... land is unsuitable for development, farming, or other economic activities due to the rugged mountain... Kalaeloa into a diversified economy. The City of Kapolei has also prepared an urban design plan that...

Patterns in species composition and diversity along intermittent creeks in the Missouri Ozarks

Treesearch

Cindy E. Becker; Stephen G. Pallardy

2003-01-01

The southeast Missouri Ozarks is a rugged, deeply dissected landscape. Intermittent creeks are commonly found throughout the region, yet our understanding of this ecosystem component is poor. Landform features, flooding frequency, and flooding duration are variables known to affect vegetation distribution patterns along perennial systems. We investigated if these...

CAD Skills Increased through Multicultural Design Project

ERIC Educational Resources Information Center

Clemons, Stephanie

2006-01-01

This article discusses how students in a college-entry-level CAD course researched four generations of their family histories and documented cultural and symbolic influences within their family backgrounds. AutoCAD software was then used to manipulate those cultural and symbolic images to create the design for a multicultural area rug. AutoCAD was…

It's time to look at yarding problems on steep slopes.

Treesearch

Robert H. Ruth

1960-01-01

In many parts of the Pacific Northwest, logging operations are moving into rugged terrain as access roads probe deeper into the back country. Because of this trend, it's time to look more carefully at steep slopes and decide on the best possible management practices consistent with maximum protection against erosion.

77 FR 46213 - Medicare Program; Prospective Payment System and Consolidated Billing for Skilled Nursing...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-02

.... Monitoring Impact of FY 2012 Policy Changes and Certain SNF Practices A. RUG Distributions B. Group Therapy... Common Procedure Coding System HR-III Hybrid Resource Utilization Groups, Version 3 IHS IGI (Information... OCN OMB Control Number OMB Office of Management and Budget OMRA Other Medicare-Required Assessment PPS...

Fourmile Canyon Fire Findings

Treesearch

Russell Graham; Mark Finney; Chuck McHugh; Jack Cohen; Dave Calkin; Rick Stratton; Larry Bradshaw; Ned Nikolov

2012-01-01

The Fourmile Canyon Fire burned in the fall of 2010 in the Rocky Mountain Front Range adjacent to Boulder, Colorado. The fire occurred in steep, rugged terrain, primarily on privately owned mixed ponderosa pine and Douglas-fir forests. The fire started on September 6 when the humidity of the air was very dry (¡Ö

An improved method for collecting and monitoring pine oleoresin

Treesearch

Dick Karsky; Brian Strom; Harold Thistle

2004-01-01

A new method for collecting and monitoring pine oleoresin has been developed through a cooperative project involving the Missoula Technology Development Center (MTDC), Southern Research Station (Brian Strom, research entomologist), and the Forest Health Technology Enterprise Team. The new sampling unit (figure 1) is cast from rugged plastic. It provides a closed system...

16 CFR 1631.33 - Carpets and rugs with fire-retardant treatment.

Code of Federal Regulations, 2010 CFR

2010-01-01

..., containing the letter “T”, legibly and conspicuously written, is delivered to the consumer in due course of... have had a fire-retardant treatment, the letter “T” shall be set forth legibly and conspicuously, and... regulations thereunder, whether or not such letter “T” appears elsewhere on said product. Samples, pieces...

Saturn Apollo Program

NASA Image and Video Library

1965-02-01

Workers at the Marshall Space Flight Center (MSFC) move a facility test version of the Saturn IB launch vehicle's second stage, the S-IVB, to the J-2 test stand on February 10, 1965. Also known as a "battleship" because of its heavy, rugged construction, the non-flight, stainless-steel model was used to check out testing facilities at MSFC.

Saturn Apollo Program

NASA Image and Video Library

1965-02-01

A facility test version of the S-IVB, the second stage of the Saturn IB launch vehicle, sits in the Marshall Space Flight Center (MSFC) J-2 test stand on February 10, 1965. Also known as a "battleship" because of its heavy, rugged construction, the non-flight, stainless-steel model was used to check out testing facilities at MSFC.

A Day at the Improv.... The Assessment and Treatment of Musculoskeletal Injuries in the Backcountry.

ERIC Educational Resources Information Center

Cochran, Brent

Outdoor leaders and those involved in personal outdoor adventure pursuits must be knowledgeable in the assessment, treatment, and prevention of musculoskeletal injuries in the backcountry. In the wilderness medicine setting, extended time periods of patient care, rugged terrain, severe environmental conditions, and limited resources create…

Landscape position moderates how ant nests affect hydrology and soil chemistry across a Chihuahuan Desert watershed

USDA-ARS?s Scientific Manuscript database

Ants moderate the supply of critical resources such as water and nutrients in desert environments by changing the physical arrangement of soils during nest construction. We measured water infiltration and soil physical and chemical properties on and off the nests of two ant species (Pogonomyrmex rug...

Note: Space qualified photon counting detector for laser time transfer with picosecond precision and stability

DOE Office of Scientific and Technical Information (OSTI.GOV)

Prochazka, Ivan, E-mail: prochiva@gmail.com; Blazej, Josef; Kodet, Jan

2016-05-15

The laser time transfer link is under construction for the European Space Agency in the frame of Atomic Clock Ensemble in Space. We have developed and tested the flying unit of the photon counting detector optimized for this space mission. The results are summarized in this Note. An extreme challenge was to build a detector package, which is rugged, small and which provides long term detection delay stability on picosecond level. The device passed successfully all the tests required for space missions on the low Earth orbits. The detector is extremely rugged and compact. Its long term detection delay stabilitymore » is excellent, it is better than ±1 ps/day, in a sense of time deviation it is better than 0.5 ps for averaging times of 2000 s to several hours. The device is capable to operate in a temperature range of −55 °C up to +60 °C, the change of the detection delay with temperature is +0.5 ps/K. The device is ready for integration into the space structure now.« less

Note: Space qualified photon counting detector for laser time transfer with picosecond precision and stability.

PubMed

Prochazka, Ivan; Kodet, Jan; Blazej, Josef

2016-05-01

The laser time transfer link is under construction for the European Space Agency in the frame of Atomic Clock Ensemble in Space. We have developed and tested the flying unit of the photon counting detector optimized for this space mission. The results are summarized in this Note. An extreme challenge was to build a detector package, which is rugged, small and which provides long term detection delay stability on picosecond level. The device passed successfully all the tests required for space missions on the low Earth orbits. The detector is extremely rugged and compact. Its long term detection delay stability is excellent, it is better than ±1 ps/day, in a sense of time deviation it is better than 0.5 ps for averaging times of 2000 s to several hours. The device is capable to operate in a temperature range of -55 °C up to +60 °C, the change of the detection delay with temperature is +0.5 ps/K. The device is ready for integration into the space structure now.

Folding of the 25 residue Abeta(12-36) peptide in TFE/water: temperature-dependent transition from a funneled free-energy landscape to a rugged one.

PubMed

Kamiya, Narutoshi; Mitomo, Daisuke; Shea, Joan-Emma; Higo, Junichi

2007-05-17

The free-energy landscape of the Alzheimer beta-amyloid peptide Abeta(12-36) in a 40% (v/v) 2,2,2-trifluoroethanol (TFE)/water solution was determined by using multicanonical molecular dynamics simulations. Simulations using this enhanced conformational sampling technique were initiated from a random unfolded polypeptide conformation. Our simulations reliably folded the peptide to the experimental NMR structure, which consists of two linked helices. The shape of the free energy landscape for folding was found to be strongly dependent on temperature: Above 325 K, the overall shape was funnel-like, with the bottom of the funnel coinciding exactly with the NMR structure. Below 325 K, on the other hand, the landscape became increasingly rugged, with the emergence of new conformational clusters connected by low free-energy pathways. Finally, our simulations reveal that water and TFE solvate the polypeptide in different ways: The hydrogen bond formation between TFE and Abeta was enhanced with decreasing temperature, while that between water and Abeta was depressed.

Topography and geomorphology of the Huygens landing site on Titan

USGS Publications Warehouse

Soderblom, L.A.; Tomasko, M.G.; Archinal, B.A.; Becker, T.L.; Bushroe, M.W.; Cook, D.A.; Doose, L.R.; Galuszka, D.M.; Hare, T.M.; Howington-Kraus, E.; Karkoschka, E.; Kirk, R.L.; Lunine, J.I.; McFarlane, E.A.; Redding, B.L.; Rizk, B.; Rosiek, M.R.; See, C.; Smith, P.H.

2007-01-01

The Descent Imager/Spectral Radiometer (DISR) aboard the Huygens Probe took several hundred visible-light images with its three cameras on approach to the surface of Titan. Several sets of stereo image pairs were collected during the descent. The digital terrain models constructed from those images show rugged topography, in places approaching the angle of repose, adjacent to flatter darker plains. Brighter regions north of the landing site display two styles of drainage patterns: (1) bright highlands with rough topography and deeply incised branching dendritic drainage networks (up to fourth order) with dark-floored valleys that are suggestive of erosion by methane rainfall and (2) short, stubby low-order drainages that follow linear fault patterns forming canyon-like features suggestive of methane spring-sapping. The topographic data show that the bright highland terrains are extremely rugged; slopes of order of 30?? appear common. These systems drain into adjacent relatively flat, dark lowland terrains. A stereo model for part of the dark plains region to the east of the landing site suggests surface scour across this plain flowing from west to east leaving ???100-m-high bright ridges. Tectonic patterns are evident in (1) controlling the rectilinear, low-order, stubby drainages and (2) the "coastline" at the highland-lowland boundary with numerous straight and angular margins. In addition to flow from the highlands drainages, the lowland area shows evidence for more prolific flow parallel to the highland-lowland boundary leaving bright outliers resembling terrestrial sandbars. This implies major west to east floods across the plains where the probe landed with flow parallel to the highland-lowland boundary; the primary source of these flows is evidently not the dendritic channels in the bright highlands to the north. ?? 2007 Elsevier Ltd. All rights reserved.

Simultaneous determination of five plant growth regulators in fruits by modified quick, easy, cheap, effective, rugged, and safe (QuEChERS) extraction and liquid chromatography-tandem mass spectrometry.

PubMed

Shi, Xiaomei; Jin, Fen; Huang, Yuting; Du, Xinwei; Li, Chunmei; Wang, Miao; Shao, Hua; Jin, Maojun; Wang, Jing

2012-01-11

An effective method using liquid chromatography-tandem mass spectrometry (LC-MS/MS) was developed and optimized to obtain a complete separation of five representative plant growth regulators (PGRs) [gibberellic acid, 2,4-dichlorophenoxyacetic acid (2,4-D), thidiazuron, forchlorfenuron, and paclobutrazol] in fruits. Extraction was performed with acetonitrile containing 0.1% (v/v) acetic acid, applying modified quick, easy, cheap, effective, rugged, and safe (QuEChERS) methodology. LC-MS/MS conditions including composition of mobile phases and mass spectrometry (MS) conditions were evaluated to achieve the highest sensitivity in MS detection. All of the data acquisition was employed in the segmented multiple-reaction monitoring mode for the selected negative and positive transition ions. The octadecylsilyl (C18) dispersive solid-phase extraction (SPE) sorbent was found to provide the more satisfied recoveries than primary secondary amine (PSA) and graphitized carbon black (GCB) for five target PGRs. The optimized method allowed for recoveries of 76-112% for the five PGRs from fruit samples with relative standard deviation (RSD) values less than 10%. Limits of quantification (0.5-16.5 μg/kg) were lower than the maximum limit of residues established for PGRs. The results demonstrated that the developed LC-MS/MS and QuEChERS extraction method is highly effective for analyzing trace amounts of target PGRs in fruit samples. Finally, the method was successfully used to detect residual PGRs in Beijing, China, in 2010. The concentrations of 2,4-D (5.1-1503 μg/kg) and paclobutrazol (1-1381 μg/kg) found in orange and peach, respectively, suggesting that the use of these PGRs in these fruits should be regulated in China in the future.

Evaluating Mass Analyzers as Candidates for Small, Portable, Rugged Single Point Mass Spectrometers for Analysis of Permanent Gases

NASA Technical Reports Server (NTRS)

Arkin, C. Richard; Ottens, Andrew K.; Diaz, Jorge A.; Griffin, Timothy P.; Follestein, Duke; Adams, Fredrick; Steinrock, T. (Technical Monitor)

2001-01-01

For Space Shuttle launch safety, there is a need to monitor the concentration of H2, He, O2 and Ar around the launch vehicle. Currently a large mass spectrometry system performs this task, using long transport lines to draw in samples. There is great interest in replacing this stationary system with several miniature, portable, rugged mass spectrometers which act as point sensors which can be placed at the sampling point. Five commercial and two non-commercial analyzers are evaluated. The five commercial systems include the Leybold Inficon XPR-2 linear quadrupole, the Stanford Research (SRS-100) linear quadrupole, the Ferran linear quadrupole array, the ThermoQuest Polaris-Q quadrupole ion trap, and the IonWerks Time-of-Flight (TOF). The non-commercial systems include a compact double focusing sector (CDFMS) developed at the University of Minnesota, and a quadrupole ion trap (UF-IT) developed at the University of Florida. The System Volume is determined by measuring the entire system volume including the mass analyzer, its associated electronics, the associated vacuum system, the high vacuum pump and rough pump. Also measured are any ion gauge controllers or other required equipment. Computers are not included. Scan Time is the time required for one scan to be acquired and the data to be transferred. It is determined by measuring the time required acquiring a known number of scans and dividing by said number of scans. Limit of Detection is determined first by performing a zero-span calibration (using a 10-point data set). Then the limit of detection (LOD) is defined as 3 times the standard deviation of the zero data set. (An LOD of 10 ppm or less is considered acceptable.)

Study on Gold and base metal occurrence in Uluwai Prospect, Western Latimojong Mountain, South Sulawesi

NASA Astrophysics Data System (ADS)

Maulana, Adi; Jaya, Asri; Imai, Akira

2018-02-01

Uluwai Prospect is located in the northern part of South Arm of Sulawesi along the eastern part of the Kalosi Fold Belt and Latimojong Mountain. The area is generally characterized by moderate to rugged topography area with elevation in the range of 700 to 1400 m above sea level in the mountainous complex called Latimojong Mountain Complex. The mineralization is characterized by a relatively simple sulphide ore mineral assemblage consists of pyrite, sphalerite and chalcopyrite. Samples were collected in areas showing abundant sulphide minerals where younger faults cut the bedding and foliation of country rocks. A number of silicified zones have been observed, as well as float material containing disseminated pyrite, chalcopyrite, and sphalerite with hematite, goethite and limonite. Some alteration types have been observed including sericitization, albitization, carbonatization and silisification. The samples collected indicated that the mineralisation is contained within metasedimentary (sandstone to mudstone) and greenschist. Geochemical analyses from 16 samples including 5 stream sediment samples indicated that the most promising mineralization occur in the prospect area are copper (Cu) and zinc (Zn). This is also supported by the abundance of chalcopyrite and sphalerite in some highly altered samples. Assaying of the collected samples revealed most of samples contain relatively low gold (Au) concentration. However, two samples contain 0.007 and 0.01 ppm of Au. In the mineralized area, Zn concentrations are up to 134 ppm, Cu up to 120 ppm and Pb up to 18 ppm and As up to 70 ppm. There is no clear relationship that exists between Au and the base metals except that one of the samples with highest Au values tend to have high Zn and As. This unclear pattern also shown by Cu, Pb and Zn. Base metal concentration in stream sediment samples show a relatively stable pattern than in rock samples. Arsenic tends to be elevated in base metal rich samples. Sb and Mo are relatively low in all sample type. However, Mo values will be high in the samples which contain highest Cu and Zn.

Inexpensive, Low Power, Open-Source Data Logging in the Field

NASA Astrophysics Data System (ADS)

Sandell, C. T.; Wickert, A. D.

2016-12-01

Collecting a robust data set of environmental conditions with commercial equipment is often cost prohibitive. I present the ALog, a general-purpose, inexpensive, low-power, open-source data logger that has proven its durability on long-term deployments in the harsh conditions of high altitude glaciers and humid river deltas. The ALog was developed to fill the need for a capable, rugged, easy-to-use, inexpensive, open-source hardware targeted at long-term remote deployment in nearly any environment. Building on the popular Arduino platform, the hardware features a high-precision clock, full size SD card slot for high-volume data storage, screw terminals, six analog inputs, two digital inputs, one digital interrupt, 3.3V and 5V power outputs, and SPI and I2C communication capability. The design is focused on extremely low power consumption allowing the Alog to be deployed for years on a single set of common alkaline batteries. The power efficiency of the Alog eliminates the difficulties associated with field power collection including additional hardware and installation costs, dependence on weather conditions, possible equipment failure, and the transport of bulky/heavy equipment to a remote site. Battery power increases suitable data collection sites (too shaded for photovoltaics) and allows for low profile installation options (including underground). The ALog has gone through continuous development with over four years of successful data collection in hydrologic field research. Over this time, software support for a wide range of sensors has been made available such as ultrasonic rangefinders (for water level, snow accumulation and glacial melt), temperature sensors (air and groundwater), humidity sensors, pyranometers, inclinometers, rain gauges, soil moisture and water potential sensors, resistance-based tools to measure frost heave, and cameras that trigger on events. The software developed for use with the ALog allows simple integration of established commercial sensors, including example implementation code so users with limited programming knowledge can get up and running with ease. All development files including design schematics, circuit board layouts, and source code files are open-source to further eliminate barriers to its use and allow community development contribution.

Analysis of Dynamic Avalanche Phenomenon in SOI Lateral High-speed Diode during Reverse Recovery and Development of a Novel Device Structure for Suppressing Dynamic Avalanche

NASA Astrophysics Data System (ADS)

Tokura, Norihito; Yamamoto, Takao; Kato, Hisato; Nakagawa, Akio

We have studied the dynamic avalanche phenomenon in an SOI lateral diode during reverse recovery by using a mixed-mode device simulation. In the study, it has been found that local impact ionization occurs near an anode-side field oxide edge, where a high-density hole current flows and a high electric field appears simultaneously. We propose that a p-type anode extension region (AER) along a trench side wall effectively sweeps out stored carriers beneath an anode p-diffusion layer during reverse recovery, resulting in reduction of the electric field and remarkable suppression of the dynamic avalanche. The AER reduces the total recovery charge and does not cause any increase in the total stored charge under a forward bias operation. This effect is verified experimentally by the fabricated device with AER. Thus, the developed SOI lateral diode is promising as a high-speed and highly rugged free-wheeling diode, which can be integrated into next-generation SOI microinverters.

Predicting landslides related to clearcut logging, northwestern California, U.S.A.

Treesearch

David J. Furbish; Raymond M. Rice

1983-01-01

Abstract - Landslides related to clearcut logging are a significant source of erosion in the mountains of northwestern California. Forest managers, therefore, frequently must include assessments of landslide risk in their land-use plans. A quantitative method is needed to predict such risk over large areas of rugged mountainous terrain. From air photographs, data...

Are We Pulling the Rug out from under Their Feet? What if Academic Interventions Are Removed?

ERIC Educational Resources Information Center

Lively Summers, Robin M.

2014-01-01

With the loss of revenue and education cut backs, school districts have faced the loss of supplemental academic supports such as after school tutoring and summer school programs. Up until recently research has focused on improving student outcomes by implementing supplemental instruction. There was little research available that examined the…

QuEChERS, a sample preparation technique that is “catching on”: an up-to-date interview with its inventors

USDA-ARS?s Scientific Manuscript database

The technique of QuEChERS (Quick, Easy, Cheap, Effective, Rugged and Safe) is only 7 years old, yet it is revolutionizing the manner in which multiresidue, multiclass pesticide analysis (and perhaps beyond) is performed. Columnist Ron Majors sits down with inventors Steve Lehotay and Michelangelo An...

Measurement of Pyrethroids and Their Environmental Degradates in Fruits and Vegetables using a Modification of the Quick Easy Cheap Effective Rugged Safe (QuEChERS) Method

EPA Science Inventory

Pyrethroid insecticides are used extensively in agriculture and they, as well as their environmental degradates, may remain as residues on food products such as fruits and vegetables. Since pyrethroid degradates can be identical to the urinary markers used in human biomonitoring ...

The Characterization of an Easy-to-Operate Inexpensive Student-Built Fluorimeter

ERIC Educational Resources Information Center

Wigton, Benjamin T.; Chohan, Balwant S.; Kreuter, Rod; Sykes, Dan

2011-01-01

A compact, rugged, and portable fluorimeter was designed and constructed using a 460 nm light-emitting diode for the excitation and a silicon photodiode for detection. The total cost of such an instrument is less than $110, thus allowing for deployment of multiple instruments at low cost. The fluorimeter is easy to operate and has been…

Section Height Determination Methods of the Isotopographic Surface in a Complex Terrain Relief

ERIC Educational Resources Information Center

Syzdykova, Guldana D.; Kurmankozhaev, Azimhan K.

2016-01-01

A new method for determining the vertical interval of isotopographic surfaces on rugged terrain was developed. The method is based on the concept of determining the differentiated size of the vertical interval using spatial-statistical properties inherent in the modal characteristic, the degree of variability of apical heights and the chosen map…

Develop real-time dosimetry concepts and instrumentation for long term missions

NASA Technical Reports Server (NTRS)

Braby, L. A.

1981-01-01

The development of a rugged portable dosimetry system, based on microdosimetry techniques, which will measure dose and evaluate dose equivalent in a mixed radiation field is described. Progress in the desired dosimetry system can be divided into three distinct areas: development of the radiation detector, and electron system are presented. The mathematical techniques required are investigated.

Memories of Morocco: The Influence of Age, Schooling, and Environment on Memory

ERIC Educational Resources Information Center

Wagner, Daniel A.

1978-01-01

The relationships of structural features of memory (e.g., short-term store) and of control processes in memory (e.g., verbal rehearsal) were compared according to age, rural-urban differences, and amount of education. Culturally-specific skills were also investigated in Moroccan rug sellers and Koranic students, and in American college students.…

16 CFR 1631.62 - Wool flokati carpets and rugs-alternative washing procedure.

Code of Federal Regulations, 2014 CFR

2014-01-01

... restore surface and fluff up fibers. 3. Spot cleaning: Remove greasy stains with a household grease remover. Remove soluble stains with lukewarm water (approximately 105 °F.) and detergent by immersing spot... a shallow pan which has been filled to a depth of 2” with a wash solution of 1.1 grams of AATCC...

16 CFR 1631.62 - Wool flokati carpets and rugs-alternative washing procedure.

Code of Federal Regulations, 2011 CFR

2011-01-01

... restore surface and fluff up fibers. 3. Spot cleaning: Remove greasy stains with a household grease remover. Remove soluble stains with lukewarm water (approximately 105 °F.) and detergent by immersing spot... a shallow pan which has been filled to a depth of 2” with a wash solution of 1.1 grams of AATCC...

16 CFR 1630.62 - Wool flokati carpets and rugs-alternative washing procedure.

Code of Federal Regulations, 2012 CFR

2012-01-01

... restore surface and fluff up fibers. 3. Spot cleaning: Remove greasy stains with a household grease remover. Remove soluble stains with lukewarm water (approximately 105 °F.) and detergent by immersing spot... a shallow pan which has been filled to a depth of 2″ with a wash solution of 1.1 grams of AATCC...

16 CFR 1630.62 - Wool flokati carpets and rugs-alternative washing procedure.

Code of Federal Regulations, 2014 CFR

2014-01-01

... restore surface and fluff up fibers. 3. Spot cleaning: Remove greasy stains with a household grease remover. Remove soluble stains with lukewarm water (approximately 105 °F.) and detergent by immersing spot... a shallow pan which has been filled to a depth of 2″ with a wash solution of 1.1 grams of AATCC...

16 CFR 1631.62 - Wool flokati carpets and rugs-alternative washing procedure.

Code of Federal Regulations, 2010 CFR

2010-01-01

... restore surface and fluff up fibers. 3. Spot cleaning: Remove greasy stains with a household grease remover. Remove soluble stains with lukewarm water (approximately 105 °F.) and detergent by immersing spot... a shallow pan which has been filled to a depth of 2” with a wash solution of 1.1 grams of AATCC...

16 CFR 1630.62 - Wool flokati carpets and rugs-alternative washing procedure.

Code of Federal Regulations, 2010 CFR

2010-01-01

... restore surface and fluff up fibers. 3. Spot cleaning: Remove greasy stains with a household grease remover. Remove soluble stains with lukewarm water (approximately 105 °F.) and detergent by immersing spot... a shallow pan which has been filled to a depth of 2″ with a wash solution of 1.1 grams of AATCC...

16 CFR 1631.62 - Wool flokati carpets and rugs-alternative washing procedure.

Code of Federal Regulations, 2012 CFR

2012-01-01

... restore surface and fluff up fibers. 3. Spot cleaning: Remove greasy stains with a household grease remover. Remove soluble stains with lukewarm water (approximately 105 °F.) and detergent by immersing spot... a shallow pan which has been filled to a depth of 2” with a wash solution of 1.1 grams of AATCC...

16 CFR 1630.62 - Wool flokati carpets and rugs-alternative washing procedure.

Code of Federal Regulations, 2011 CFR

2011-01-01

... restore surface and fluff up fibers. 3. Spot cleaning: Remove greasy stains with a household grease remover. Remove soluble stains with lukewarm water (approximately 105 °F.) and detergent by immersing spot... a shallow pan which has been filled to a depth of 2″ with a wash solution of 1.1 grams of AATCC...

Sharing the Arts of the Blue Ridge Mountains. Final Report, February 1977-January 1978.

ERIC Educational Resources Information Center

Holman, Martha; Gailey, Lamar

Designed to utilize basic skills and develop a vocational or vocational skills, eight adult basic education modules were developed which highlight authentic Blue Ridge Mountain crafts. Modules provide instruction in apple dolls, braided rugs, candles, caning, corn shuck dolls, pottery, quilting, and weaving (see Note). Selection of the crafts was…

Safety for Older Consumers. Home Safety Checklist.

ERIC Educational Resources Information Center

Consumer Product Safety Commission, Washington, DC.

A home safety checklist geared to the needs of older adults is presented in this document. The beginning of the checklist highlights potential hazards which may need to be checked in more than one area of the home, such as electric cords, smoke detectors, rugs, telephone areas, and emergency exit plans. The rest of the checklist is organized…

77 FR 48505 - Submission for OMB Review; Comment Request-Flammability Standards for Carpets and Rugs

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-14

... passing test results, then only one test per year is required. For purposes of estimating burden, we have... mail/hand delivery/courier (for paper, disk, or CD-ROM submissions), preferably in five copies, to... to perform each year varies, depending upon the number of carpet styles and the annual volume of...

A variable circular-plot method for estimating bird numbers

Treesearch

R. T. Reynolds; J. M. Scott; R. A. Nussbaum

1980-01-01

A bird census method is presented that is designed for tall, structurally complex vegetation types, and rugged terrain. With this method the observer counts all birds seen or heard around a station, and estimates the horizontal distance from the station to each bird. Count periods at stations vary according to the avian community and structural complexity of the...

Forest succession following wildfire and sudden oak death epidemic

Treesearch

Clay M. DeLong; Kerri M. Frangioso; Margaret R. Metz; Ross K. Meentemeyer; Dave M. Rizzo

2013-01-01

The Big Sur region of central California is a rugged, fire-prone area that has been severely affected by Phytophthora ramorum. Meentemeyer et al. (2008) estimated that over 200,000 oaks and tanoaks had been killed by P. ramorum across the Big Sur ecoregion by 2005. In June of 2008, a complex of lightning-initiated...

Legacy of the American West: Indian Cowboys, Black Cowboys, and Vaqueros

ERIC Educational Resources Information Center

Gandy, S. Kay

2008-01-01

The cowboy is viewed as an American icon: rider of the open range, rugged individual, and champion of good. Cowboys are still very much a part of American culture today. Why is it important to study cowboys? The introduction of cattle and horses by the Spanish "conquistadors" transformed the local culture, influenced the economics of the…