Jet impact on a soap film

NASA Astrophysics Data System (ADS)

Kirstetter, Geoffroy; Raufaste, Christophe; Celestini, Franck

2012-09-01

We experimentally investigate the impact of a liquid jet on a soap film. We observe that the jet never breaks the film and that two qualitatively different steady regimes may occur. The first one is a refractionlike behavior obtained at small incidence angles when the jet crosses the film and is deflected by the film-jet interaction. For larger incidence angles, the jet is absorbed by the film, giving rise to a new class of flows in which the jet undulates along the film with a characteristic wavelength. Besides its fundamental interest, this paper presents a different way to guide a micrometric flow of liquid in the inertial regime and to probe foam stability submitted to violent perturbations at the soap film scale.

Jet impact on a soap film.

PubMed

Kirstetter, Geoffroy; Raufaste, Christophe; Celestini, Franck

2012-09-01

We experimentally investigate the impact of a liquid jet on a soap film. We observe that the jet never breaks the film and that two qualitatively different steady regimes may occur. The first one is a refractionlike behavior obtained at small incidence angles when the jet crosses the film and is deflected by the film-jet interaction. For larger incidence angles, the jet is absorbed by the film, giving rise to a new class of flows in which the jet undulates along the film with a characteristic wavelength. Besides its fundamental interest, this paper presents a different way to guide a micrometric flow of liquid in the inertial regime and to probe foam stability submitted to violent perturbations at the soap film scale.

Hydrodynamics of soap films probed by two-particle microrheology

NASA Astrophysics Data System (ADS)

Prasad, Vikram; Weeks, Eric R.

2007-11-01

A soap film consists of a thin water layer that is separated from two bulk air phases above and below it by surfactant monolayers. The flow fields in the soap film created in response to a perturbation depend on coupling between these different phases, the exact nature of which is unknown. In order to determine this coupling, we use polystyrene spheres as tracer particles and track their diffusive motions in the soap film. The correlated Brownian motion of pairs of particles (two-particle microrheology) maps out the flow field, and provides a measure of the surface viscosity of the soap film as well. This measured surface viscosity agrees well with the value obtained from self diffusion of single particles (one-particle microrheology) in the film.

Sound and vision: visualization of music with a soap film

NASA Astrophysics Data System (ADS)

Gaulon, C.; Derec, C.; Combriat, T.; Marmottant, P.; Elias, F.

2017-07-01

A vertical soap film, freely suspended at the end of a tube, is vibrated by a sound wave that propagates in the tube. If the sound wave is a piece of music, the soap film ‘comes alive’: colours, due to iridescences in the soap film, swirl, split and merge in time with the music (see the snapshots in figure 1 below). In this article, we analyse the rich physics behind these fascinating dynamical patterns: it combines the acoustic propagation in a tube, the light interferences, and the static and dynamic properties of soap films. The interaction between the acoustic wave and the liquid membrane results in capillary waves on the soap film, as well as non-linear effects leading to a non-oscillatory flow of liquid in the plane of the film, which induces several spectacular effects: generation of vortices, diphasic dynamical patterns inside the film, and swelling of the soap film under certain conditions. Each of these effects is associated with a characteristic time scale, which interacts with the characteristic time of the music play. This article shows the richness of those characteristic times that lead to dynamical patterns. Through its artistic interest, the experiments presented in this article provide a tool for popularizing and demonstrating science in the classroom or to a broader audience.

The microjet-film interaction: the interaction and resulting shapes of a liquid microjet impacting a soap film

NASA Astrophysics Data System (ADS)

Chan, Jau Tung; Lee, Jie Liang; Tjeng, Vincent; Yeo, Ye; Tan, Guoxian

2014-11-01

The International Young Physicists’ Tournament (IYPT) is a worldwide annual competition for high-school students. This paper is adapted from the solution to problem 8, Jet and Film, as presented by the Singapore Team at the 26th IYPT, Taipei, Taiwan. The impact of liquid microjets on stable soap films was investigated. Two steady regimes were observed: refraction (where the microjet penetrates the soap film and is deflected) and absorption (where the microjet merges with the soap film and forms vertical undulating patterns on the soap film surface). This phenomenon has potential applications in controlling the trajectory of a liquid microjet in air. Although Kirstetter et al (2012) investigated this interaction by using the same liquid for both the microjet and the soap film, this paper extends their work by using different liquids for the microjet and the soap film. In addition, the need for a small-angle approximation of Snell’s law is removed for the refraction regime, and an alternative expression is proposed for the force exerted by the soap film on the microjet in the absorption regime that accounts for the dependence of the wavelength of the undulating patterns on the angle of incidence of the microjet on the soap film. Empirical data support these improved theoretical predictions.

Numerical Analysis of Transient Temperature Response of Soap Film

NASA Astrophysics Data System (ADS)

Tanaka, Seiichi; Tatesaku, Akihiro; Dantsuka, Yuki; Fujiwara, Seiji; Kunimine, Kanji

2015-11-01

Measurements of thermophysical properties of thin liquid films are important to understand interfacial phenomena due to film structures composed of amphiphilic molecules in soap film, phospholipid bilayer of biological cell and emulsion. A transient hot-wire technique for liquid films less than 1 \\upmu m thick such as soap film has been proposed to measure the thermal conductivity and diffusivity simultaneously. Two-dimensional heat conduction equations for a solid cylinder with a liquid film have been solved numerically. The temperature of a thin wire with liquid film increases steeply with its own heat generation. The feasibility of this technique is verified through numerical experiments for various thermal conductivities, diffusivities, and film thicknesses. Calculated results indicate that the increase in the volumetric average temperature of the thin wire sufficiently varies with the change of thermal conductivity and diffusivity of the soap film. Therefore, the temperature characteristics could be utilized to evaluate both the thermal conductivity and diffusivity using the Gauss-Newton method.

Elasticity of a soap film junction

NASA Astrophysics Data System (ADS)

Elias, F.; Janiaud, E.; Bacri, J.-C.; Andreotti, B.

2014-03-01

We investigate the elasticity of an isolated, threefold junction of soap films (Plateau border), which displays static undulations when liquid rapidly flows into it. By analyzing the shape of the Plateau border (thickness R and transverse displacement) as a function of the liquid flow rate Q, we show experimentally and theoretically that the elasticity of the Plateau border is dominated by the bending of the soap films pulling on the Plateau border. In this asymptotic regime, the undulation wavelength obeys the scaling law ˜Q2 R-2 and the decay length ˜Q2 R-4.

Soap-film coating: High-speed deposition of multilayer nanofilms

PubMed Central

Zhang, Renyun; Andersson, Henrik A.; Andersson, Mattias; Andres, Britta; Edlund, Håkan; Edström, Per; Edvardsson, Sverker; Forsberg, Sven; Hummelgård, Magnus; Johansson, Niklas; Karlsson, Kristoffer; Nilsson, Hans-Erik; Norgren, Magnus; Olsen, Martin; Uesaka, Tetsu; Öhlund, Thomas; Olin, Håkan

2013-01-01

The coating of thin films is applied in numerous fields and many methods are employed for the deposition of these films. Some coating techniques may deposit films at high speed; for example, ordinary printing paper is coated with micrometre-thick layers of clay at a speed of tens of meters per second. However, to coat nanometre thin films at high speed, vacuum techniques are typically required, which increases the complexity of the process. Here, we report a simple wet chemical method for the high-speed coating of films with thicknesses at the nanometre level. This soap-film coating technique is based on forcing a substrate through a soap film that contains nanomaterials. Molecules and nanomaterials can be deposited at a thickness ranging from less than a monolayer to several layers at speeds up to meters per second. We believe that the soap-film coating method is potentially important for industrial-scale nanotechnology. PMID:23503102

The fluid trampoline: droplets bouncing on a soap film

NASA Astrophysics Data System (ADS)

Bush, John; Gilet, Tristan

2008-11-01

We present the results of a combined experimental and theoretical investigation of droplets falling onto a horizontal soap film. Both static and vertically vibrated soap films are considered. A quasi-static description of the soap film shape yields a force-displacement relation that provides excellent agreement with experiment, and allows us to model the film as a nonlinear spring. This approach yields an accurate criterion for the transition between droplet bouncing and crossing on the static film; moreover, it allows us to rationalize the observed constancy of the contact time and scaling for the coefficient of restitution in the bouncing states. On the vibrating film, a variety of bouncing behaviours were observed, including simple and complex periodic states, multiperiodicity and chaos. A simple theoretical model is developed that captures the essential physics of the bouncing process, reproducing all observed bouncing states. Quantitative agreement between model and experiment is deduced for simple periodic modes, and qualitative agreement for more complex periodic and chaotic bouncing states.

Influence of Evaporation on Soap Film Rupture.

PubMed

Champougny, Lorène; Miguet, Jonas; Henaff, Robin; Restagno, Frédéric; Boulogne, François; Rio, Emmanuelle

2018-03-13

Although soap films are prone to evaporate due to their large surface to volume ratio, the effect of evaporation on macroscopic film features has often been disregarded in the literature. In this work, we experimentally investigate the influence of environmental humidity on soap film stability. An original experiment allows to measure both the maximum length of a film pulled at constant velocity and its thinning dynamics in a controlled atmosphere for various values of the relative humidity [Formula: see text]. At first order, the environmental humidity seems to have almost no impact on most of the film thinning dynamics. However, we find that the film length at rupture increases continuously with [Formula: see text]. To rationalize our observations, we propose that film bursting occurs when the thinning due to evaporation becomes comparable to the thinning due to liquid drainage. This rupture criterion turns out to be in reasonable agreement with an estimation of the evaporation rate in our experiment.

Quasi-steady vortical structures in vertically vibrating soap films

NASA Astrophysics Data System (ADS)

Vega, José M.; Higuera, F. J.; Weidman, P. D.

1998-10-01

An analysis of the quasi-steady streaming of the liquid in a vertically vibrated horizontal soap film is reported. The air around the soap film is seen to play a variety of roles: it transmits normal and tangential oscillatory stresses to the film, damps out Marangoni waves, and forces non-oscillatory deflection of the film and tangential motion of the liquid. Non-oscillatory volume forcing originating inside the liquid is also analysed. This forcing dominates the quasi-steady streaming when the excitation frequency is close to the eigenfrequency of a Marangoni mode of the soap film, while both volume forcing in the liquid and surface forcing of the gas on the liquid are important when no Marangoni mode resonates. Different manners by which the combined forcings can induce quasi-steady streaming motion are discussed and some numerical simulations of the quasi-steady liquid flow are presented.

Laser-induced vibration of a thin soap film.

PubMed

Emile, Olivier; Emile, Janine

2014-09-21

We report on the vibration of a thin soap film based on the optical radiation pressure force. The modulated low power laser induces a counter gravity flow in a vertical free-standing draining film. The thickness of the soap film is then higher in the upper region than in the lower region of the film. Moreover, the lifetime of the film is dramatically increased by a factor of 2. Since the laser beam only acts mechanically on the film interfaces, such a film can be employed in an optofluidic diaphragm pump, the interfaces behaving like a vibrating membrane and the liquid in-between being the fluid to be pumped. Such a pump could then be used in delicate micro-equipment, in chips where temperature variations are detrimental and even in biological systems.

Memory effects in soap film arrangements

NASA Astrophysics Data System (ADS)

Vandewalle, Nicolas; Dorbolo, Stephane; Lumay, Geoffroy; Schockmel, Julien; Noirhomme, Martial

2012-02-01

We report experiments on soap film configurations in a triangular prism for which the shape factor can be changed continuously. Two stable configurations can be observed for a range of the shape factor h. A hysteretic behaviour is found, due to the occurence of another local minima in the free energy. Experiments demonstrate that soap films can be trapped in a particular configuration being different from a global surface minimization. This metastability can be evidenced from a geometrical model based on idealized structures. Depending on the configuration, providing clues on the structural relaxations taking place into 3D foams, such as T1 rearrangements. The composition of the liquid is also investigated leading to dynamical picture of the transition. (Phys. Rev. E 83, 021403 (2011))

A public study of the lifetime distribution of soap films

NASA Astrophysics Data System (ADS)

Tobin, S. T.; Meagher, A. J.; Bulfin, B.; Möbius, M.; Hutzler, S.

2011-08-01

We present data for the lifetime distribution of soap films made from commercial dish-washing solution and contained in sealed cylinders. Data for over 2500 films were gathered during a 2-month exhibition on the science and art of bubbles and foams in Dublin's Science Gallery. Visitors to the gallery were invited to create 10-20 parallel soap films in acrylic tubes which were sealed with cork stoppers. Individual film bursts occurred at random and were uncorrelated. The total number of remaining films in the tubes was recorded every day. Visitors could monitor the status of their soap film tube and the daily updated histogram of the lifetime of all films. The histogram of the bubble lifetimes is well described by a Weibull distribution, which indicates that the failure rate is not constant and increases over time. Unsealed cylinders show drastically reduced film lifetimes. This experiment illustrates the difference between the unpredictability of the lifetime of individual films and the existence of a well-defined lifetime distribution for the ensemble.

RiskSOAP: Introducing and applying a methodology of risk self-awareness in road tunnel safety.

PubMed

Chatzimichailidou, Maria Mikela; Dokas, Ioannis M

2016-05-01

Complex socio-technical systems, such as road tunnels, can be designed and developed with more or less elements that can either positively or negatively affect the capability of their agents to recognise imminent threats or vulnerabilities that possibly lead to accidents. This capability is called risk Situation Awareness (SA) provision. Having as a motive the introduction of better tools for designing and developing systems that are self-aware of their vulnerabilities and react to prevent accidents and losses, this paper introduces the Risk Situation Awareness Provision (RiskSOAP) methodology to the field of road tunnel safety, as a means to measure this capability in this kind of systems. The main objective is to test the soundness and the applicability of RiskSOAP to infrastructure, which is advanced in terms of technology, human integration, and minimum number of safety requirements imposed by international bodies. RiskSOAP is applied to a specific road tunnel in Greece and the accompanying indicator is calculated twice, once for the tunnel design as defined by updated European safety standards and once for the 'as-is' tunnel composition, which complies with the necessary safety requirements, but calls for enhancing safety according to what EU and PIARC further suggest. The derived values indicate the extent to which each tunnel version is capable of comprehending its threats and vulnerabilities based on its elements. The former tunnel version seems to be more enhanced both in terms of it risk awareness capability and safety as well. Another interesting finding is that despite the advanced tunnel safety specifications, there is still room for enriching the safe design and maintenance of the road tunnel. Copyright © 2016 Elsevier Ltd. All rights reserved.

Modeling drop impacts on inclined flowing soap films

NASA Astrophysics Data System (ADS)

Basu, Saikat; Yawar, Ali; Concha, Andres; Bandi, Mahesh

2015-11-01

Small drops impinging on soap films flowing at an angle primarily exhibit three fundamental regimes of post-impact dynamics: (a) the drop bounces off the film surface, (b) it coalesces with the downstream flow, and (c) it pierces through the film. During impact, the drop deforms along with a simultaneous, almost elastic deformation of the film transverse to the stream direction. Hence, the governing dynamics for this interaction present the rare opportunity to explore the in-tandem effects of elasticity and hydrodynamics alike. In this talk, we outline the analytical framework to study the drop impact dynamics. The model assumes a deformable drop and a deformable three-dimensional soap film and invokes a parametric study to qualify the three mentioned impact types. The physical parameters include the impact angle, drop impact speed, and the diameters of the drop prior to and during impact when it deforms and spreads out. Our model system offers a path towards optimization of interactions between a spray and a flowing liquid.

Motion of Colloidal Particles near Plateau Border in Freely Suspended Soap Film

NASA Astrophysics Data System (ADS)

Pak, Hyuk Kyu; Sur, Jeanman

2000-03-01

We study the motion of colloidal particle near Plateau border in free-standing soap film which is placed perpendicularly to the gravitational direction. When the thickness of soap film is a micron order, two air/water interfacial surfaces of the film can be deformed by the presence of the colloidal particle. When the colloidal particles are in the central area of soap film, they move in random directions. But, as the particles approach near Plateau border, they are accelerated to the border of the film. The travelling distance, before the accelerated particle stops, depends on particle size. We propose a simple model to explain the motion of particle near Plateau border using a surface energy argument and compare the results with experimental measurements.

An Experimental Study of the Effect of Viscosity on Bouncing Soap Droplets onto a Horizontal Soap Film

NASA Astrophysics Data System (ADS)

Gunter, Amy-Lee; Ng, Hoi Dick

2012-11-01

This experimental study aims to investigate the phenomenon of a bouncing soap droplet on a horizontal soap film, and how this behavior is affected by variations in the glycerol content of the solution for both the droplet and film. Direct visualization of the bouncing dynamics using high-speed photography allows determination of droplet size and rebound height as the viscosity is varied. In addition, the upper and lower limits of the mixture composition at which the viscosity of the fluid prevents the droplet from bouncing are determined. A thorough examination of this fluid trampoline was recently conducted by Gilet and Bush, the focus of which was to compare the effect of vibration in the soap film [T. Gilet and J.W.M. Bush, J. Fluid Mech. 625: 167-203, 2009]. A small amount of attention was given to the effect of viscosity changes in the droplet and film, and this work aims to expand on those findings. This work is supported by the Natural Sciences and Engineering Research Council of Canada (NSERC).

Soap-film flow induced by electric fields in asymmetric frames

NASA Astrophysics Data System (ADS)

Mollaei, S.; Nasiri, M.; Soltanmohammadi, N.; Shirsavar, R.; Ramos, A.; Amjadi, A.

2018-04-01

Net fluid flow of soap films induced by (ac or dc) electric fields in asymmetric frames is presented. Previous experiments of controllable soap film flow required the simultaneous use of an electrical current passing through the film and an external electric field or the use of nonuniform ac electric fields. Here a single voltage difference generates both the electrical current going through the film and the electric field that actuates on the charge induced on the film. The film is set into global motion due to the broken symmetry that appears by the use of asymmetric frames. If symmetric frames are used, the film flow is not steady but time dependent and irregular. Finally, we study numerically these film flows by employing the model of charge induction in ohmic liquids.

Soap-film flow induced by electric fields in asymmetric frames.

PubMed

Mollaei, S; Nasiri, M; Soltanmohammadi, N; Shirsavar, R; Ramos, A; Amjadi, A

2018-04-01

Net fluid flow of soap films induced by (ac or dc) electric fields in asymmetric frames is presented. Previous experiments of controllable soap film flow required the simultaneous use of an electrical current passing through the film and an external electric field or the use of nonuniform ac electric fields. Here a single voltage difference generates both the electrical current going through the film and the electric field that actuates on the charge induced on the film. The film is set into global motion due to the broken symmetry that appears by the use of asymmetric frames. If symmetric frames are used, the film flow is not steady but time dependent and irregular. Finally, we study numerically these film flows by employing the model of charge induction in ohmic liquids.

Surface tension profiles in vertical soap films

NASA Astrophysics Data System (ADS)

Adami, N.; Caps, H.

2015-01-01

Surface tension profiles in vertical soap films are experimentally investigated. Measurements are performed by introducing deformable elastic objets in the films. The shape adopted by those objects once set in the film is related to the surface tension value at a given vertical position by numerically solving the adapted elasticity equations. We show that the observed dependency of the surface tension versus the vertical position is predicted by simple modeling that takes into account the mechanical equilibrium of the films coupled to previous thickness measurements.

A miracle happening to a laser beam in a soap film

DOE Office of Scientific and Technical Information (OSTI.GOV)

Startsev, Aleksandr V; Stoilov, Yurii Yu

2003-05-31

When a 10 {mu}W - 3 W laser beam (for example, at 632.8 nm) is focused into a usual soap film of thickness between 10 nm and 10 {mu}m from the side or through a defect on the film surface, the self-channeling of the beam propagating in the film is observed. The beam also exhibits self-branching into submicron filaments, the so-called whiskers of length several tens of centimetres. The results of experiments on the dynamics of behaviour of these whiskers in a soap film, their polariton nature, and possible applications are discussed. (letters)

Wire Frame Holds Water-Soap Film in Space

NASA Technical Reports Server (NTRS)

2003-01-01

Expedition 6 astronaut Dr. Don Pettit photographed a cube shaped wire frame supporting a thin film made from a water-soap solution during his Saturday Morning Science aboard the International Space Station's (ISS) Destiny Laboratory. Food coloring was added to several faces to observe the effects of diffusion within the film.

Observation and simulation of flow on soap film induced by concentration gradient

NASA Astrophysics Data System (ADS)

Ohnishi, Mitsuru; Yoshihara, Shoichi; Azuma, Hisao

The behavior of the flow and capillary wave induced on the film surface by the surfactant concentration difference is studied. Flat soap film is used as a model of thin film. The result is applicable to the case of flow by thermal gradient. The Schlieren method is used to observe the flow and the wave on the soap film. It is found that the wave velocities, in the case of a high surface tension difference, are linearly related to the square root of the surface tension difference.

"Marginal pinching" in soap films

NASA Astrophysics Data System (ADS)

Aradian, A.; Raphaël, E.; de Gennes, P.-G.

2001-09-01

We discuss the behaviour of a thin soap film facing a frame element: the pressure in the Plateau border around the frame is lower than the film pressure, and the film thins out over a certain distance λ(t), due to the formation of a well-localized pinched region of thickness h(t) and extension w(t). We construct a hydrodynamic theory for this thinning process, assuming a constant surface tension: Marangoni effects are probably important only at late stages, where instabilities set in. We find λ(t) ~ t1/4, and for the pinch dimensions, h(t) ~ t-1/2 and w(t) ~ t-1/4. These results may play a useful role for the discussion of later instabilities leading to a global film thinning and drainage, as first discussed by K. Mysels under the name "marginal regeneration".

Role of surface elasticity in the drainage of soap films

NASA Astrophysics Data System (ADS)

Sonin, A. A.; Bonfillon, A.; Langevin, D.

1993-10-01

We present measurements of the thinning velocity of circular horizontal soap films made from dilute surfactant solutions (around the critical micellar concentration). We have solved numerically the hydrodynamic equations for the drainage process. After data fitting, we deduce the values of the elasticities of the surfactant monolayer that stabilizes the soap film. These elasticity values have been compared to elasticities obtained independently from the study of waves at the surface of the solution. The comparison reveals the importance of surface convection in the drainage process and demonstrates the important role of surface elasticity.

How are soap bubbles blown? Fluid dynamics of soap bubble blowing

NASA Astrophysics Data System (ADS)

Davidson, John; Lambert, Lori; Sherman, Erica; Wei, Timothy; Ryu, Sangjin

2013-11-01

Soap bubbles are a common interfacial fluid dynamics phenomenon having a long history of delighting not only children and artists but also scientists. In contrast to the dynamics of liquid droplets in gas and gas bubbles in liquid, the dynamics of soap bubbles has not been well documented. This is possibly because studying soap bubbles is more challenging due to there existing two gas-liquid interfaces. Having the thin-film interface seems to alter the characteristics of the bubble/drop creation process since the interface has limiting factors such as thickness. Thus, the main objective of this study is to determine how the thin-film interface differentiates soap bubbles from gas bubbles and liquid drops. To investigate the creation process of soap bubbles, we constructed an experimental model consisting of air jet flow and a soap film, which consistently replicates the conditions that a human produces when blowing soap bubbles, and examined the interaction between the jet and the soap film using the high-speed videography and the particle image velocimetry.

Soap films burst like flapping flags.

PubMed

Lhuissier, Henri; Villermaux, Emmanuel

2009-07-31

When punctured, a flat soap film bursts by opening a hole driven by liquid surface tension. The hole rim does not, however, remain smooth but soon develops indentations at the tip of which ligaments form, ultimately breaking and leaving the initially connex film into a mist of disjointed drops. We report on original observations showing that these indentations result from a flaglike instability between the film and the surrounding atmosphere inducing an oscillatory motion out of its plane. Just like a flag edge flaps in the wind, the film is successively accelerated on both sides perpendicularly to its plane, inducing film thickness modulations and centrifuging liquid ligaments that finally pinch off to form the observed spray. This effect exemplifies how the dynamics of fragile objects such as thin liquid films is sensitive to their embedding medium.

Soap Films and GeoGebra in the Study of Fermat and Steiner Points

ERIC Educational Resources Information Center

Flores, Alfinio; Park, Jungeun

2018-01-01

We discuss how mathematics and secondary mathematics education majors developed an understanding of Fermat points for the triangle as well as Steiner points for the square and regular pentagon, and also of soap film configurations between parallel plates where forces are in equilibrium. The activities included the use of soap films and the…

Soap film vibration: origin of the dissipation.

PubMed

Acharige, Sébastien Kosgodagan; Elias, Florence; Derec, Caroline

2014-11-07

We investigate the complex dispersion relationship of a transverse antisymmetric wave on a horizontal soap film. Experimentally, the complex wave number k at a fixed forcing frequency is determined by measuring the vibrating amplitude of the soap film: the wavelength (linked to the real part of k) is determined by the spatial variation of the amplitude; the decay length (linked to the imaginary part of k) is determined by analyzing the resonance curves of the vibrating wave as a function of frequency. Theoretically, we compute the complex dispersion relationship taking into account the physical properties of the bulk liquid and gas phase, and of the gas-liquid interfaces. The comparison between the computation (developed to the leading order under our experimental conditions) and the experimental results confirms that the phase velocity is fixed by the interplay between surface tension, and liquid and air inertia, as reported in previous studies. Moreover, we show that the attenuation of the transverse antisymmetric wave originates from the viscous dissipation in the gas phase surrounding the liquid film. This result is an important step in understanding the propagation of an acoustic wave in liquid foam, using a bottom-up approach.

Thin film instabilities: Rayleigh-Taylor with thermocapillarity and Kolmogorov flow in a soap film

NASA Astrophysics Data System (ADS)

Burgess, John Matthew

The Rayleigh-Taylor instability occurs when a more dense fluid layer is suspended above a less dense fluid layer in a gravitational field. The horizontal interface between the two fluids is unstable to infinitesimal deformations and the dense fluid falls. To counteract the destabilizing effects of gravity on the interface between two thin fluid layers, we apply a vertical temperature gradient, heating from below. The dependence of surface tension on temperature (``thermocapillarity'') can cause spatially-varying interfacial forces between two immiscible fluid layers if a variation in temperature along the interface is introduced. With an applied vertical temperature gradient, the deforming interface spontaneously develops temperature variations which locally adjust the surface tension to restore a flat interface. We find that these surface tension gradients can stabilize a more dense thin fluid layer (silicone oil, 0.015 cm thick) above a less dense thin fluid layer (air, 0.025 cm thick) in a gravitational field, in qualitative agreement with linear stability analysis. This is the first experimental observation of the stabilization of Rayleigh-Taylor instability by thermocapillary forces. We also examine the instability of a soap film flow driven by a time-independent force that is spatially periodic in the direction perpendicular to the forcing (Kolmogorov flow). The film is in the x- y plane, where the forcing approximates a shape sin (y)x̂. Linear stability analysis of an idealized model of this flow predicts a critical Reynolds number Rc~2 . In our soap film experiment, we find a critical value Rc~70 . This discrepancy can be ascribed to frictional effects from viscous coupling of gas to the film, which is neglected in the idealized model. The kinematic viscosity of the surrounding gas and the thickness of gas layers on each side of the soap film are varied in the experiments to better understand these frictional effects. We conclude that

On the nature of laser polariton tracks in soap films

DOE Office of Scientific and Technical Information (OSTI.GOV)

Startsev, Aleksandr V; Stoilov, Yurii Yu

2004-06-30

The results of the study of narrow laser tracks in soap films with the divergence below the diffraction-limited value are presented, and the mechanism of formation of narrow channels (spatial polariton solitons) based on laser dielectrophoresis in films is proposed. (nonlinear optical phenomena)

Sudden Thickening in Flowing Soap Films

NASA Astrophysics Data System (ADS)

Goldburg, Walter; Steers, Stanley; Hartman, Nikolaus

2007-11-01

There is no difficulty in creating soap films that flow vertically downward under gravity at speeds of the order of a m/s. If the height of the film L0 is of the order of 1 m or less, the film thickness h(x) is a few microns (The coordinate x increases downward below the injection point at x = 0.) However if L0 is of the order of 2 m, one finds that h abruptly increases at a sharply defined value of x =L. In the experiments to be described, L ˜ =.9 m. As expected, the vertical film velocity vx(x) correspondingly drops to a small fraction of its upstream value at x ˜L. In the narrow transition region from thin to thick film at x=L, both h(x) and the vx(x) oscillate at a well-defined frequency of the order of 1 Hz. The abrupt thickening is expected on the basis of singular perturbation theory (T. Tran, following paper).

Monitoring the thinning dynamics of soap films by phase shift interferometry. The case of perfluoropolyether surfactants.

PubMed

Gambi, Cecilia M C; Vannoni, Maurizio; Sordini, Andrea; Molesini, Giuseppe

2014-02-01

An interferometric method to monitor the thinning process of vertical soap films from a water solution of surfactant materials is reported. Raw data maps of optical path difference introduced by the film are obtained by conventional phase shift interferometry. Off-line re-processing of such raw data taking into account the layered structure of soap films leads to an accurate measurement of the geometrical thickness. As an example of data acquisition and processing, the measuring chain is demonstrated on perfluoropolyether surfactants; the section profile of vertical films is monitored from drawing to black film state, and quantitative data on the dynamics of the thinning process are presented. The interferometric method proves effective to the task, and lends itself to further investigate the physical properties of soap films.

Confocal micro-Raman spectroscopy of black soap films

NASA Astrophysics Data System (ADS)

Lecourt, B.; Capelle, F.; Adamietz, F.; Malaplate, A.; Blaudez, D.; Kellay, H.; Turlet, J. M.

1998-01-01

Black soap films from aqueous solutions of sodium dodecyl sulphate are studied by micro-Raman confocal spectroscopy. At the end of the draining process films of different thicknesses are obtained depending on the experimental conditions: Working in a closed humidified chamber leads to common black films while, under evaporation or in the presence of electrolyte, Newton black films are observed. From the Raman spectra of these films, quantitative information is deduced about the conformational and lateral order of the aliphatic surfactant chains, as well as the thickness of the residual water layer. More accurate measurements of the thickness of these ultimate films have been carried out by transmission ellipsometry and their effective refractive index measured by Brewster angle reflectivity. The thinner films present higher molecular organization and their aqueous core exhibits unusual spectral features.

Measurement of contact-line dissipation in a nanometer-thin soap film

NASA Astrophysics Data System (ADS)

Guo, Shuo; Lee, Chun Huen; Sheng, Ping; Tong, Penger

2015-01-01

We report a direct measurement of the friction coefficient ξc of two fluctuating contact lines formed on a fiber surface when a long glass fiber intersects the two water-air interfaces of a thin soap film. The glass fiber of diameter d in the range of 0.4-4 μ m and length 100-300 μ m is glued onto the front end of a rectangular cantilever used for atomic force microscopy. As a sensitive mechanical resonator, the hanging fiber probe can accurately measure a minute change of its viscous damping caused by the soap film. By measuring the broadening of the resonant peak of the hanging fiber probe with varying viscosity η of the soap film and different surface treatments of the glass fiber, we confirm that the contact line dissipation obeys a universal scaling law, ξc=α π d η , where the coefficient α =1.1 ±0.3 is insensitive to the change of liquid-solid contact angle. The experimental result is in good agreement with the numerical result based on the phase field model under the generalized Navier boundary conditions.

Measurement of contact-line dissipation in a nanometer-thin soap film.

PubMed

Guo, Shuo; Lee, Chun Huen; Sheng, Ping; Tong, Penger

2015-01-01

We report a direct measurement of the friction coefficient ξ(c) of two fluctuating contact lines formed on a fiber surface when a long glass fiber intersects the two water-air interfaces of a thin soap film. The glass fiber of diameter d in the range of 0.4-4 μm and length 100-300 μm is glued onto the front end of a rectangular cantilever used for atomic force microscopy. As a sensitive mechanical resonator, the hanging fiber probe can accurately measure a minute change of its viscous damping caused by the soap film. By measuring the broadening of the resonant peak of the hanging fiber probe with varying viscosity η of the soap film and different surface treatments of the glass fiber, we confirm that the contact line dissipation obeys a universal scaling law, ξ(c)=απdη, where the coefficient α=1.1±0.3 is insensitive to the change of liquid-solid contact angle. The experimental result is in good agreement with the numerical result based on the phase field model under the generalized Navier boundary conditions.

Fibrillar films obtained from sodium soap fibers and polyelectrolyte multilayers.

PubMed

Zawko, Scott A; Schmidt, Christine E

2011-08-01

An objective of tissue engineering is to create synthetic polymer scaffolds with a fibrillar microstructure similar to the extracellular matrix. Here, we present a novel method for creating polymer fibers using the layer-by-layer method and sacrificial templates composed of sodium soap fibers. Soap fibers were prepared from neutralized fatty acids using a sodium chloride crystal dissolution method. Polyelectrolyte multilayers (PEMs) of polystyrene sulfonate and polyallylamine hydrochloride were deposited onto the soap fibers, crosslinked with glutaraldehyde, and then the soap fibers were leached with warm water and ethanol. The morphology of the resulting PEM structures was a dense network of fibers surrounded by a nonfibrillar matrix. Microscopy revealed that the PEM fibers were solid structures, presumably composed of polyelectrolytes complexed with residual fatty acids. These fibrillar PEM films were found to support the attachment of human dermal fibroblasts. Copyright © 2011 Wiley Periodicals, Inc.

Drainage Behavior in Soap Films Above and Below the CMC

NASA Astrophysics Data System (ADS)

Berg, S.; Adelizzi, E. A.; Troian, S. M.

2003-11-01

We investigate through laser interferometry the drainage behavior of Newtonian soap films initially entrained on a fiber frame at small and constant capillary number. The initial film thickness is sufficiently small that gravitational drainage is presumed minimal. The drainage of rigid soap films by capillary forces alone should proceed according to h(t) ˜ t^- 1/2. Our experimental results show much more rapid drainage with exponents as large as -2, especially for those solutions whose surfactant concentrations are below the CMC. Video recordings of the entire film surface reveal a variety of structures during the drainage process, some attributable to marginal regeneration. Though still a controversial issue, this regeneration process is believed to be caused by surfactant accumulation in the meniscus region (1). We show that modification of the relevant capillary drainage equation to account for Marangoni effects through a course-grained slip condition at the air-liquid interface produces exponents in better agreement with experimental findings. (1) V. A. Nierstrasz and G. Frens, JCIS 215, 28 (1999).

Boundary singularities produced by the motion of soap films.

PubMed

Goldstein, Raymond E; McTavish, James; Moffatt, H Keith; Pesci, Adriana I

2014-06-10

Recent work has shown that a Möbius strip soap film rendered unstable by deforming its frame changes topology to that of a disk through a "neck-pinching" boundary singularity. This behavior is unlike that of the catenoid, which transitions to two disks through a bulk singularity. It is not yet understood whether the type of singularity is generally a consequence of the surface topology, nor how this dependence could arise from an equation of motion for the surface. To address these questions we investigate experimentally, computationally, and theoretically the route to singularities of soap films with different topologies, including a family of punctured Klein bottles. We show that the location of singularities (bulk or boundary) may depend on the path of the boundary deformation. In the unstable regime the driving force for soap-film motion is the mean curvature. Thus, the narrowest part of the neck, associated with the shortest nontrivial closed geodesic of the surface, has the highest curvature and is the fastest moving. Just before onset of the instability there exists on the stable surface the shortest closed geodesic, which is the initial condition for evolution of the neck's geodesics, all of which have the same topological relationship to the frame. We make the plausible conjectures that if the initial geodesic is linked to the boundary, then the singularity will occur at the boundary, whereas if the two are unlinked initially, then the singularity will occur in the bulk. Numerical study of mean curvature flows and experiments support these conjectures.

Boundary singularities produced by the motion of soap films

PubMed Central

Goldstein, Raymond E.; McTavish, James; Moffatt, H. Keith; Pesci, Adriana I.

2014-01-01

Recent work has shown that a Möbius strip soap film rendered unstable by deforming its frame changes topology to that of a disk through a “neck-pinching” boundary singularity. This behavior is unlike that of the catenoid, which transitions to two disks through a bulk singularity. It is not yet understood whether the type of singularity is generally a consequence of the surface topology, nor how this dependence could arise from an equation of motion for the surface. To address these questions we investigate experimentally, computationally, and theoretically the route to singularities of soap films with different topologies, including a family of punctured Klein bottles. We show that the location of singularities (bulk or boundary) may depend on the path of the boundary deformation. In the unstable regime the driving force for soap-film motion is the mean curvature. Thus, the narrowest part of the neck, associated with the shortest nontrivial closed geodesic of the surface, has the highest curvature and is the fastest moving. Just before onset of the instability there exists on the stable surface the shortest closed geodesic, which is the initial condition for evolution of the neck’s geodesics, all of which have the same topological relationship to the frame. We make the plausible conjectures that if the initial geodesic is linked to the boundary, then the singularity will occur at the boundary, whereas if the two are unlinked initially, then the singularity will occur in the bulk. Numerical study of mean curvature flows and experiments support these conjectures. PMID:24843162

Mapping of the Marangoni effect in soap films using Young's double-slit experiment

NASA Astrophysics Data System (ADS)

Emile, Janine; Emile, Olivier

2013-10-01

We report on the thickness variation measurement of a soap film due to a local perturbation, using Young's double-slit experiment configuration. We map a laser-heated deformation of a vertical free-standing draining thin soap film using the differential change of optical path in the interferometer. The experiment has a resolution of about 0.1 nm and enables to follow the liquid flow dynamics. We evidence a bottleneck formation in the heated region of the film that perturbs the usual flow. Such an experimental set-up could then be adapted to measure other tiny variations in fluctuating hydrodynamics such as capillary waves for example.

Thermal Convection in Two-Dimensional Soap Films

NASA Astrophysics Data System (ADS)

Zhang, Jie; Wu, X. L.

2002-11-01

Thermal convection in a fluid is a common phenomenon. Due to thermal expansion, the light warm fluid at the bottom tends to rise and the cold, heavier fluid at the top tends to fall. This so-called thermal convection exists in earth atmosphere and in oceans. It is also an important mechanism by which energy is transported in stars. In this study we investigate thermal convection in a vertical soap film.

Bernoulli Suction Effect on Soap Bubble Blowing?

NASA Astrophysics Data System (ADS)

Davidson, John; Ryu, Sangjin

2015-11-01

As a model system for thin-film bubble with two gas-liquid interfaces, we experimentally investigated the pinch-off of soap bubble blowing. Using the lab-built bubble blower and high-speed videography, we have found that the scaling law exponent of soap bubble pinch-off is 2/3, which is similar to that of soap film bridge. Because air flowed through the decreasing neck of soap film tube, we studied possible Bernoulli suction effect on soap bubble pinch-off by evaluating the Reynolds number of airflow. Image processing was utilized to calculate approximate volume of growing soap film tube and the volume flow rate of the airflow, and the Reynolds number was estimated to be 800-3200. This result suggests that soap bubbling may involve the Bernoulli suction effect.

Measuring and Overcoming Limits of the Saffman-Delbrück Model for Soap Film Viscosities

PubMed Central

Vivek, Skanda; Weeks, Eric R.

2015-01-01

We observe tracer particles diffusing in soap films to measure the two-dimensional (2D) viscous properties of the films. Saffman-Delbrück type models relate the single-particle diffusivity to parameters of the film (such as thickness h) for thin films, but the relation breaks down for thicker films. Notably, the diffusivity is faster than expected for thicker films, with the crossover at h/d = 5.2 ± 0.9 using the tracer particle diameter d. This indicates a crossover from purely 2D diffusion to diffusion that is more three-dimensional. We demonstrate that measuring the correlations of particle pairs as a function of their separation overcomes the limitations of the Saffman-Delbrück model and allows one to measure the viscosity of a soap film for any thickness. PMID:25822262

Measuring and overcoming limits of the Saffman-Delbrück model for soap film viscosities.

PubMed

Vivek, Skanda; Weeks, Eric R

2015-01-01

We observe tracer particles diffusing in soap films to measure the two-dimensional (2D) viscous properties of the films. Saffman-Delbrück type models relate the single-particle diffusivity to parameters of the film (such as thickness h) for thin films, but the relation breaks down for thicker films. Notably, the diffusivity is faster than expected for thicker films, with the crossover at h/d = 5.2 ± 0.9 using the tracer particle diameter d. This indicates a crossover from purely 2D diffusion to diffusion that is more three-dimensional. We demonstrate that measuring the correlations of particle pairs as a function of their separation overcomes the limitations of the Saffman-Delbrück model and allows one to measure the viscosity of a soap film for any thickness.

The generation of two-dimensional vortices by transverse oscillation of a soap film

DOE Office of Scientific and Technical Information (OSTI.GOV)

Afenchenko, V.O.; Ezersky, A.B.; Kiyashko, S.V.

1998-02-01

An experimental investigation of the dynamics of horizontal soap films stretched over circular or square boundaries undergoing periodic transverse oscillations at frequencies in the range 20{endash}200 Hz is reported. Concomitant with modes of transverse flexural oscillations, it was observed that two-dimensional vortices in the plane of the film are excited. The vortices may be either (i) large, scaling with the size of the cavity or (ii) small, localized at a wavelength or half-wavelength of the membrane modes. In the experiments a stable generation of one, two, {hor_ellipsis}, ten pairs of counter-rotating vortices were observed in finite regions of amplitude-frequency parametermore » space. The circulation strength of vortices in a given vortex pattern increases with increasing external forcing and with decreasing soap film thickness. A theoretical model based on the wave-boundary interaction of excited Marangoni waves reveals a vorticity generation mechanism active in vibrating soap films. This model shows that vorticity is generated throughout the entire liquid volume by viscous diffusion, and qualitatively reproduces many steady vortex patterns observed in the experiment. However, the model cannot explain the existence of the sometimes intense vortices observed far from the film boundary that do not appear to be generated by diffusive processes. {copyright} {ital 1998 American Institute of Physics.}« less

What is the mechanism of soap film entrainment?

PubMed

Saulnier, Laurie; Restagno, Frédéric; Delacotte, Jérôme; Langevin, Dominique; Rio, Emmanuelle

2011-11-15

Classical Frankel's law describes the formation of soap films and their evolution upon pulling, a model situation of film dynamics in foams (formation, rheology, and destabilization). With the purpose of relating film pulling to foam dynamics, we have built a new setup able to give an instantaneous measurement of film thickness, thus allowing us to determine film thickness profile during pulling. We found that only the lower part of the film is of uniform thickness and follows Frankel's law, provided the entrainment velocity is small. We show that this is due to confinement effects: there is not enough surfactant in the bulk to fully cover the newly created surfaces which results in immobile film surfaces. At large velocities, surfaces become mobile and then Frankel's law breaks down, leading to a faster drainage and thus to a nonstationary thickness at the bottom of the film. These findings should help in understanding the large dispersion of previous experimental data reported during the last 40 years and clarifying the pulling phenomenon of thin liquid films.

Collapse of the soap-film bridge - Quasistatic description

NASA Astrophysics Data System (ADS)

Cryer, Steven A.; Steen, Paul H.

1992-11-01

Observations of the collapse of a soap-film bridge from a connected to a disconnected state are recorded. The equilibrium framework for this nonequilibrium event is classical. Experiments confirm predictions of stable and unstable equilibria. A quasistatic description is introduced for the dynamic states to extend the static theory. It is found to adequately describe the collapse trajectory while the bridge is still connected.

Collapse of the soap-film bridge - Quasistatic description

NASA Technical Reports Server (NTRS)

Cryer, Steven A.; Steen, Paul H.

1992-01-01

Observations of the collapse of a soap-film bridge from a connected to a disconnected state are recorded. The equilibrium framework for this nonequilibrium event is classical. Experiments confirm predictions of stable and unstable equilibria. A quasistatic description is introduced for the dynamic states to extend the static theory. It is found to adequately describe the collapse trajectory while the bridge is still connected.

Dynamics of a single flexible filament in a flowing soap film

NASA Astrophysics Data System (ADS)

Chen, Chaonan; Feng, Shunshan; Zhou, Tong

2016-11-01

The interactions between flexible plates and surrounding fluids like two-dimensional flag-in-wind problems are important physical phenomena. Here we use a spandex filament with one end fixed flapping in gravity-driven soap film device which can be regarded as a quasi-two-dimensional flow tunnel. A silk filament had been used previously to demonstrate three stable dynamical states: stretched-straight, flapping, and bistable states. The similar phenomena occured for a spandex filament while the bifurcation conditions seem to be different compared with a silk filament, as the critical filament length is longer and critical inflow velocity is higher than that for a silk filament. In the experiment, we considered some representative parameters (filament length, inflow velocity, and bending stiffness of the filament) to study their effects on the stability of the filament and its bifurcation conditions. An interface-tracking ALE finite element method was then conducted to reproduce the experiment and investigate more details about effects of these parameters. which are significant to reveal the underlying mechanism of flag-in-wind problem. Corresponding Author. Email:zhoutong@bit.edu.cn.

Visualization of Sound Waves Using Regularly Spaced Soap Films

ERIC Educational Resources Information Center

Elias, F.; Hutzler, S.; Ferreira, M. S.

2007-01-01

We describe a novel demonstration experiment for the visualization and measurement of standing sound waves in a tube. The tube is filled with equally spaced soap films whose thickness varies in response to the amplitude of the sound wave. The thickness variations are made visible based on optical interference. The distance between two antinodes is…

Soap film flows: Statistics of two-dimensional turbulence

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vorobieff, P.; Rivera, M.; Ecke, R.E.

1999-08-01

Soap film flows provide a very convenient laboratory model for studies of two-dimensional (2-D) hydrodynamics including turbulence. For a gravity-driven soap film channel with a grid of equally spaced cylinders inserted in the flow, we have measured the simultaneous velocity and thickness fields in the irregular flow downstream from the cylinders. The velocity field is determined by a modified digital particle image velocimetry method and the thickness from the light scattered by the particles in the film. From these measurements, we compute the decay of mean energy, enstrophy, and thickness fluctuations with downstream distance, and the structure functions of velocity,more » vorticity, thickness fluctuation, and vorticity flux. From these quantities we determine the microscale Reynolds number of the flow R{sub {lambda}}{approx}100 and the integral and dissipation scales of 2D turbulence. We also obtain quantitative measures of the degree to which our flow can be considered incompressible and isotropic as a function of downstream distance. We find coarsening of characteristic spatial scales, qualitative correspondence of the decay of energy and enstrophy with the Batchelor model, scaling of energy in {ital k} space consistent with the k{sup {minus}3} spectrum of the Kraichnan{endash}Batchelor enstrophy-scaling picture, and power-law scalings of the structure functions of velocity, vorticity, vorticity flux, and thickness. These results are compared with models of 2-D turbulence and with numerical simulations. {copyright} {ital 1999 American Institute of Physics.}« less

Soap films and GeoGebra in the study of Fermat and Steiner points

NASA Astrophysics Data System (ADS)

Flores, Alfinio; Park, Jungeun

2018-05-01

We discuss how mathematics and secondary mathematics education majors developed an understanding of Fermat points for the triangle as well as Steiner points for the square and regular pentagon, and also of soap film configurations between parallel plates where forces are in equilibrium. The activities included the use of soap films and the interactive geometry program GeoGebra. Students worked in small groups using these tools to investigate the properties of Fermat and Steiner points and then justified the results of their investigations using geometrical arguments. These activities are specific approaches of how to encourage prospective teachers to use physical experiments to support students' development of mathematical curiosity and mathematical justifications.

A free-flowing soap film combined with cavity ring-down spectroscopy as a detection system for liquid chromatography.

PubMed

Vogelsang, Markus; Welsch, Thomas; Jones, Harold

2010-05-07

We have shown that a free-flowing soap film has sufficiently high-quality optical properties to allow it to be used in the cavity of a ring-down spectrometer (CRDS). The flow rates required to maintain a stable soap film were similar to those used in liquid chromatography and thus allowed interfacing with an HPLC system for use as an optical detector. We have investigated the properties of the system in a relevant analytical application. The soap film/CRDS combination was used at 355 nm as a detector for the separation of a mixture of nitroarenes. These compounds play a role in the residue analysis of areas contaminated with explosives and their decomposition products. In spite of the short absorption path length (9 microm) obtained by the soap film, the high-sensitivity of CRDS allowed a limit of detection of 4 x 10(-6) in absorption units (AU) or less than 17 fmol in the detection volume to be achieved. Copyright (c) 2009 Elsevier B.V. All rights reserved.

How does a soap film burst during generation?

NASA Astrophysics Data System (ADS)

Rio, Emmanuelle; Saulnier, Laurie; Restagno, Frederic; Langevin, Dominique

2011-11-01

Foams are dispersions of bubbles in a liquid matrix in the presence of stabilizing surfactants. Even if foams are ubiquitous, the ability of a solution to create a certain foam quantity is still not fully understood. As a first step, we choose to work on a simplified system and studied the stability of a soap film during its generation. We have built an experiment, in which we determine simultaneously the velocity of a frame pulled out of a soapy solution and the entire shape of the liquid film. We found that the film is made of two parts: the bottom part is of uniform and stationary thickness, well described by the classical Frankel's law; in the top part, the film drains until a black film appears near the frame upper boundary frame, and then bursts. In this study, we characterize both part of the films and show that the Frankel law breaks down at high capillary number due to surfactants confinement. We also explain why films pulled at high velocity have a shorter lifetime than those pulled at low velocity. L. Saulnier is funded by CNES.

Extension of a suspended soap film: a homogeneous dilatation followed by new film extraction.

PubMed

Seiwert, Jacopo; Monloubou, Martin; Dollet, Benjamin; Cantat, Isabelle

2013-08-30

Liquid foams are widely used in industry for their high effective viscosity, whose local origin is still unclear. This Letter presents new results on the extension of a suspended soap film, in a configuration mimicking the elementary deformation occurring during foam shearing. We evidence a surprising two-step evolution: the film first extends homogeneously, then its extension stops, and a new thicker film is extracted from the meniscus. The second step is independent of the nature of the surfactant solution, whereas the initial extension is only observed for surfactant solutions with negligible dilatational moduli. We predict this complex behavior using a model based on Frankel's theory and on interface rigidification induced by confinement.

Extension of a Suspended Soap Film: A Homogeneous Dilatation Followed by New Film Extraction

NASA Astrophysics Data System (ADS)

Seiwert, Jacopo; Monloubou, Martin; Dollet, Benjamin; Cantat, Isabelle

2013-08-01

Liquid foams are widely used in industry for their high effective viscosity, whose local origin is still unclear. This Letter presents new results on the extension of a suspended soap film, in a configuration mimicking the elementary deformation occurring during foam shearing. We evidence a surprising two-step evolution: the film first extends homogeneously, then its extension stops, and a new thicker film is extracted from the meniscus. The second step is independent of the nature of the surfactant solution, whereas the initial extension is only observed for surfactant solutions with negligible dilatational moduli. We predict this complex behavior using a model based on Frankel’s theory and on interface rigidification induced by confinement.

Relativistic strings - From soap films to a grand unified theory

NASA Astrophysics Data System (ADS)

Nesterenko, V. V.

1986-11-01

The concept of relativistic strings is considered in connection with the theory of minimal surfaces (e.g., soap films stretched onto closed wire contours). The role of relativistic strings in hadron physics is discussed. Attention is then given to the creation of a grand unified theory on the basis of the superstring concept. Finally, the role of relativistic strings in cosmology is examined.

Wake visualization of a heaving and pitching foil in a soap film

NASA Astrophysics Data System (ADS)

Muijres, Florian T.; Lentink, David

2007-11-01

Many fish depend primarily on their tail beat for propulsion. Such a tail is commonly modeled as a two-dimensional flapping foil. Here we demonstrate a novel experimental setup of such a foil that heaves and pitches in a soap film. The vortical flow field generated by the foil correlates with thickness variations in the soap film, which appear as interference fringes when the film is illuminated with a monochromatic light source (we used a high-frequency SOX lamp). These interference fringes are subsequently captured with high-speed video (500 Hz) and this allows us to study the unsteady vortical field of a flapping foil. The main advantage of our approach is that the flow fields are time and space resolved and can be obtained time-efficiently. The foil is driven by a flapping mechanism that is optimized for studying both fish swimming and insect flight inside and outside the behavioral envelope. The mechanism generates sinusoidal heave and pitch kinematics, pre-described by the non-dimensional heave amplitude (0-6), the pitch amplitude (0°-90°), the phase difference between pitch and heave (0°-360°), and the dimensionless wavelength of the foil (3-18). We obtained this wide range of wavelengths for a foil 4 mm long by minimizing the soap film speed (0.25 m s-1) and maximizing the flapping frequency range (4-25 Hz). The Reynolds number of the foil is of order 1,000 throughout this range. The resulting setup enables an effective assessment of vortex wake topology as a function of flapping kinematics. The efficiency of the method is further improved by carefully eliminating background noise in the visualization (e.g., reflections of the mechanism). This is done by placing mirrors at an angle behind the translucent film such that the camera views the much more distant and out-of-focus reflections of the black laboratory wall. The resulting high-quality flow visualizations require minimal image processing for flow interpretation. Finally, we demonstrate the

Wake visualization of a heaving and pitching foil in a soap film

NASA Astrophysics Data System (ADS)

Muijres, Florian T.; Lentink, David

Many fish depend primarily on their tail beat for propulsion. Such a tail is commonly modeled as a twodimensional flapping foil. Here we demonstrate a novel experimental setup of such a foil that heaves and pitches in a soap film. The vortical flow field generated by the foil correlates with thickness variations in the soap film, which appear as interference fringes when the film is illuminated with a monochromatic light source (we used a high-frequency SOX lamp). These interference fringes are subsequently captured with high-speed video (500 Hz) and this allows us to study the unsteady vortical field of a flapping foil. The main advantage of our approach is that the flow fields are time and space resolved and can be obtained time-efficiently. The foil is driven by a flapping mechanism that is optimized for studying both fish swimming and insect flight inside and outside the behavioral envelope. The mechanism generates sinusoidal heave and pitch kinematics, pre-described by the non-dimensional heave amplitude (0-6), the pitch amplitude (0° - 90°), the phase difference between pitch and heave (0° - 360°), and the dimensionless wavelength of the foil (3-18). We obtained this wide range of wavelengths for a foil 4 mm long by minimizing the soap film speed (0.25 m s- 1) and maximizing the flapping frequency range (4-25 Hz). The Reynolds number of the foil is of order 1,000 throughout this range. The resulting setup enables an effective assessment of vortex wake topology as a function of flapping kinematics. The efficiency of the method is further improved by carefully eliminating background noise in the visualization (e.g., reflections of the mechanism). This is done by placing mirrors at an angle behind the translucent film such that the camera views the much more distant and out-of-focus reflections of the black laboratory wall. The resulting high-quality flow visualizations require minimal image processing for flow interpretation. Finally, we demonstrate the

Giant optical activity of sugar in thin soap films.

PubMed

Emile, Janine; Emile, Olivier; Ghoufi, Aziz; Moréac, Alain; Casanova, Federico; Ding, Minxia; Houizot, Patrick

2013-10-15

We report on enhanced experimental optical activity measurements of thin soap films in the presence of sugar. This unusual optical activity is linked to the intramolecular chiral conformation of the glucose molecules at the air/liquid interface. Choosing sodium dodecylsulfate (SDS) as a model surfactant and glucose as model sugar, favorable interactions between the anionic group -OSO3(-)- and the glucose molecules are highlighted. This induces an interfacial anchoring of glucose molecules leading to a perturbing influence of the asymmetric chiral environment. Copyright © 2013 Elsevier Inc. All rights reserved.

Visualization of airflow growing soap bubbles

NASA Astrophysics Data System (ADS)

Al Rahbi, Hamood; Bock, Matthew; Ryu, Sangjin

2016-11-01

Visualizing airflow inside growing soap bubbles can answer questions regarding the fluid dynamics of soap bubble blowing, which is a model system for flows with a gas-liquid-gas interface. Also, understanding the soap bubble blowing process is practical because it can contribute to controlling industrial processes similar to soap bubble blowing. In this study, we visualized airflow which grows soap bubbles using the smoke wire technique to understand how airflow blows soap bubbles. The soap bubble blower setup was built to mimic the human blowing process of soap bubbles, which consists of a blower, a nozzle and a bubble ring. The smoke wire was placed between the nozzle and the bubble ring, and smoke-visualized airflow was captured using a high speed camera. Our visualization shows how air jet flows into the growing soap bubble on the ring and how the airflow interacts with the soap film of growing bubble.

Layering Transitions and Squeeze-Out Patterns in Nanoscale Polymeric Soap Films

NASA Astrophysics Data System (ADS)

Berg, Steffen; Troian, Sandra M.

2004-11-01

Oscillatory forces in freely suspended or confined nanofilms of micellar solutions, colloidal suspensions, alkanes and semidilute polyelectrolyte films generate stepwise thinning during the final stages of film drainage. The step jump correlates with the basic aggregation unit such as the micellar size or the polymer mesh size. In all studies so far reported, the interface separating films of different thickness is circular or elliptical, as seen in common or Newton black films. Our studies of freely suspended soaps films containing an anionic surfactant and nonionic polymer have revealed that the last stratification event expands with a fractal boundary whose dimension increases with the solution viscosity above a critical value. Unstable front propagation resembles a viscous fingering instability. We propose that internal film layering due to confinement of polymer-surfactant aggregates leads to a smaller viscosity in the thinnest film (≈ 12 nm), which rapidly penetrates into an exterior layer (≈ 62 nm) of higher viscosity. Subsequent coarsening of the fractal interface mimics shapes recently observed in macroscopic systems.

A simple geometrical model describing shapes of soap films suspended on two rings

NASA Astrophysics Data System (ADS)

Herrmann, Felix J.; Kilvington, Charles D.; Wildenberg, Rebekah L.; Camacho, Franco E.; Walecki, Wojciech J.; Walecki, Peter S.; Walecki, Eve S.

2016-09-01

We measured and analysed the stability of two types of soap films suspended on two rings using the simple conical frusta-based model, where we use common definition of conical frustum as a portion of a cone that lies between two parallel planes cutting it. Using frusta-based we reproduced very well-known results for catenoid surfaces with and without a central disk. We present for the first time a simple conical frusta based spreadsheet model of the soap surface. This very simple, elementary, geometrical model produces results surprisingly well matching the experimental data and known exact analytical solutions. The experiment and the spreadsheet model can be used as a powerful teaching tool for pre-calculus and geometry students.

Influence of boundary conditions on the existence and stability of minimal surfaces of revolution made of soap films

NASA Astrophysics Data System (ADS)

Salkin, Louis; Schmit, Alexandre; Panizza, Pascal; Courbin, Laurent

2014-09-01

Because of surface tension, soap films seek the shape that minimizes their surface energy and thus their surface area. This mathematical postulate allows one to predict the existence and stability of simple minimal surfaces. After briefly recalling classical results obtained in the case of symmetric catenoids that span two circular rings with the same radius, we discuss the role of boundary conditions on such shapes, working with two rings having different radii. We then investigate the conditions of existence and stability of other shapes that include two portions of catenoids connected by a planar soap film and half-symmetric catenoids for which we introduce a method of observation. We report a variety of experimental results including metastability—an hysteretic evolution of the shape taken by a soap film—explained using simple physical arguments. Working by analogy with the theory of phase transitions, we conclude by discussing universal behaviors of the studied minimal surfaces in the vicinity of their existence thresholds.

"In Situ" Observation of a Soap-Film Catenoid--A Simple Educational Physics Experiment

ERIC Educational Resources Information Center

Ito, Masato; Sato, Taku

2010-01-01

The solution to the Euler-Lagrange equation is an extremal functional. To understand that the functional is stationary at local extrema (maxima or minima), we propose a physics experiment that involves using a soap film to form a catenoid. A catenoid is a surface that is formed between two coaxial circular rings and is classified mathematically as…

Guanidine Soaps As Vehicles For Coating Ceramic Fibers

NASA Technical Reports Server (NTRS)

Philipp, Warren H.; Veitch, Lisa C.; Jaskowiak, Martha H.

1994-01-01

Soaps made from strong organic base guanidine and organic fatty acids serve as vehicles and binders for coating ceramic fibers, various smooth substrates, and other problematic surfaces with thin precious-metal or metal-oxide films. Films needed to serve as barriers to diffusion in fiber/matrix ceramic composite materials. Guanidine soaps entirely organic and burn off, leaving no residues.

Steiner trees and spanning trees in six-pin soap films

NASA Astrophysics Data System (ADS)

Dutta, Prasun; Khastgir, S. Pratik; Roy, Anushree

2010-02-01

The problem of finding minimum (local as well as absolute) path lengths joining given points (or terminals) on a plane is known as the Steiner problem. The Steiner problem arises in finding the minimum total road length joining several towns and cities. We study the Steiner tree problem using six-pin soap films. Experimentally, we observe spanning trees as well as Steiner trees partly by varying the pin diameter. We propose a possibly exact expression for the length of a spanning tree or a Steiner tree, which fails mysteriously in certain cases.

On angled bounce-off impact of a drop impinging on a flowing soap film

NASA Astrophysics Data System (ADS)

Basu, Saikat; Yawar, Ali; Concha, Andres; Bandi, M. M.

2017-12-01

Small drops impinging obliquely on thin flowing soap films frequently demonstrate the rare emergence of bulk elastic effects working in-tandem with the more commonplace hydrodynamic interactions. Three collision regimes are observable: (a) drop piercing through the film, (b) it coalescing with the flow, and (c) it bouncing off the film surface. During impact, the drop deforms along with a bulk elastic deformation of the film. For impacts that are close-to-tangential, the bounce-off regime predominates. We outline a reduced order analytical framework assuming a deformable drop and a deformable three-dimensional film, and the idealization invokes a phase-based parametric study. Angular inclination of the film and the ratio of post and pre-impact drop sizes entail the phase parameters. We also perform experiments with vertically descending droplets (constituted from deionized water) impacting against an inclined soap film, flowing under constant pressure head. Model-predicted phase domain for bounce-off compares well to our experimental findings. Additionally, the experiments exhibit momentum transfer to the film in the form of shed vortex dipoles, along with propagation of free surface waves. On consulting prior published work, we note that for locomotion of water-walking insects using an impulsive action, the momentum distribution to the shed vortices and waves are both significant, taking up respectively 2/3 and 1/3 of the imparted streamwise momentum. Considering the visually similar impulse actions, this theory, despite its assumption of a quiescent liquid bath of infinite depth, is applied to the drop bounce-off experiments, and the resultant shed vortex dipole momenta are compared to the momenta of the coherent vortex structures computed from particle imaging velocimetry data. The magnitudes reveal identical order (10-7 N s), suggesting that notwithstanding the disparities, the bounce-off regime may be tapped as a toy analog for impulse-based interfacial

Viscosity of particulate soap films: approaching the jamming of 2D capillary suspensions.

PubMed

Timounay, Yousra; Rouyer, Florence

2017-05-14

We compute the effective viscosity of particulate soap films thanks to local velocity fields obtained by Particle Image Velocimetry (PIV) during film retraction experiments. We identify the jamming of these 2D capillary suspensions at a critical particle surface fraction (≃0.84) where effective viscosity diverges. Pair correlation function and number of neighbors in contact or close to contact reveal the cohesive nature of this 2D capillary granular media. The experimental 2D dynamic viscosities can be predicted by a model considering viscous dissipation at the liquid interfaces induced by the motion of individual particles.

Dynamics of the formation of an aureole in the bursting of soap films

NASA Astrophysics Data System (ADS)

Liang, N. Y.; Chan, C. K.; Choi, H. J.

1996-10-01

The thickness profiles of the aureole created in the bursting of vertical soap films are studied by a fast line scan charge-coupled device camera. Detail dynamics of the aureole are reported. Phenomena of the wavelike motions of the bursting rim and detachments of the aureole from the bursting film are also observed. We find that the stability of the aureole increases with the surfactant concentrations and is sensitive to the types of surfactant being used. The concentration dependence suggests that the interaction of micelles might be important in the bursting process. Furthermore, the surfactant monolayer in the aureole is found to be highly compressed and behaves like a rigid film. Existing theories of the aureole formation cannot account for all the observed phenomena.

Soap Bubble Spectra.

ERIC Educational Resources Information Center

Siddons, Colin

1984-01-01

Describes an apparatus (called the "Rainbow Cup") used for demonstrating the colored rings produced by constructive interference in soap films. Discusses construction of the Rainbow Cup and gives hints for its use in the classroom, especially in relation to classroom humidity. (JM)

Soap bubbles in analytical chemistry. Conductometric determination of sub-parts per million levels of sulfur dioxide with a soap bubble.

PubMed

Kanyanee, Tinakorn; Borst, Walter L; Jakmunee, Jaroon; Grudpan, Kate; Li, Jianzhong; Dasgupta, Purnendu K

2006-04-15

Soap bubbles provide a fascinating tool that is little used analytically. With a very low liquid volume to surface area ratio, a soap bubble can potentially provide a very useful interface for preconcentration where mass transfer to an interfacial surface is important. Here we use an automated system to create bubbles of uniform size and film thickness. We utilize purified Triton-X 100, a nonionic surfactant, to make soap bubbles. We use such bubbles as a gas-sampling interface. Incorporating hydrogen peroxide into the bubble provides a system where electrical conductance increases as the bubble is exposed to low concentrations of sulfur dioxide gas. We theoretically derive the conductance of a hollow conducting spherical thin film with spherical cap electrodes. We measure the film thickness by incorporating a dye in the bubble making solution and laser transmission photometry and find that it agrees well with the geometrically computed thickness. With the conductance of the bubble-making soap solution being measured by conventional methods, we show that the measured values of the bubble conductance with known bubble and electrode dimensions closely correspond to the theoretically computed value. Finally, we demonstrate that sub-ppm levels of SO(2) can readily be detected by the conductivity change of a hydrogen peroxide-doped soap bubble, measured in situ, when the gas flows around the bubble.

Dimensional effects on the tunneling conductivity of gold-implanted nanocomposite films

NASA Astrophysics Data System (ADS)

Grimaldi, C.; Cattani, M.; Salvadori, M. C.

2015-03-01

We study the dependence of the electrical conductivity on the gold concentration of Au-implanted polymethylmethacrylate (PMMA) and alumina nanocomposite thin films. For Au contents larger than a critical concentration, the conductivity of Au-PMMA and Au-alumina is well described by percolation in two dimensions, indicating that the critical correlation length for percolation is larger than the thickness of the films. Below the critical loading, the conductivity is dominated by tunneling processes between isolated Au particles dispersed in PMMA or alumina continuous matrices. Using an effective medium analysis of the tunneling conductivity, we show that Au-PMMA behaves as a tunneling system in two dimensions, as the film thickness is comparable to the mean Au particle size. On the contrary, the conductivity of Au-alumina films is best described by tunneling in three dimensions, although the film thickness is only a few times larger than the particle size. We interpret the enhancement of the effective dimensionality of Au-alumina films in the tunneling regime as due to the larger film thickness as compared to the mean interparticle distances.

Tunneling studies of compositionally modulated PB/Fe films

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wawro, A.; Witek, A.; Majewski, J.

1988-01-01

Preliminary results of preparation and investigation of compositionally modulated Pb/Fe films are reported. These films have been used as electrodes in Al/Al/sub 2/O/sub 3//{kappa}(Pb/Fe) tunnel junctions and the tunnelling characteristics I-V, dV/dI and d/sup 2/V/d/I/sup 2/ vs V have been studied in dependence on the modulation period.

Soap bubbles in paintings: Art and science

NASA Astrophysics Data System (ADS)

Behroozi, F.

2008-12-01

Soap bubbles became popular in 17th century paintings and prints primarily as a metaphor for the impermanence and fragility of life. The Dancing Couple (1663) by the Dutch painter Jan Steen is a good example which, among many other symbols, shows a young boy blowing soap bubbles. In the 18th century the French painter Jean-Simeon Chardin used soap bubbles not only as metaphor but also to express a sense of play and wonder. In his most famous painting, Soap Bubbles (1733/1734) a translucent and quavering soap bubble takes center stage. Chardin's contemporary Charles Van Loo painted his Soap Bubbles (1764) after seeing Chardin's work. In both paintings the soap bubbles have a hint of color and show two bright reflection spots. We discuss the physics involved and explain how keenly the painters have observed the interaction of light and soap bubbles. We show that the two reflection spots on the soap bubbles are images of the light source, one real and one virtual, formed by the curved surface of the bubble. The faint colors are due to thin film interference effects.

Pinch-off Scaling Law of Soap Bubbles

NASA Astrophysics Data System (ADS)

Davidson, John; Ryu, Sangjin

2014-11-01

Three common interfacial phenomena that occur daily are liquid drops in gas, gas bubbles in liquid and thin-film bubbles. One aspect that has been studied for these phenomena is the formation or pinch-off of the drop/bubble from the liquid/gas threads. In contrast to the formation of liquid drops in gas and gas bubbles in liquid, thin-film bubble pinch-off has not been well documented. Having thin-film interfaces may alter the pinch-off process due to the limiting factor of the film thickness. We observed the pinch-off of one common thin-film bubble, soap bubbles, in order to characterize its pinch-off behavior. We achieved this by constructing an experimental model replicating the process of a human producing soap bubbles. Using high-speed videography and image processing, we determined that the minimal neck radius scaled with the time left till pinch-off, and that the scaling law exponent was 2/3, similar to that of liquid drops in gas.

Electrowetting of soap bubbles

NASA Astrophysics Data System (ADS)

Arscott, Steve

2013-07-01

A proof-of-concept demonstration of the electrowetting-on-dielectric of a sessile soap bubble is reported here. The bubbles are generated using a commercial soap bubble mixture—the surfaces are composed of highly doped, commercial silicon wafers covered with nanometer thick films of Teflon®. Voltages less than 40 V are sufficient to observe the modification of the bubble shape and the apparent bubble contact angle. Such observations open the way to inter alia the possibility of bubble-transport, as opposed to droplet-transport, in fluidic microsystems (e.g., laboratory-on-a-chip)—the potential gains in terms of volume, speed, and surface/volume ratio are non-negligible.

On the use of helium-filled soap bubbles for large-scale tomographic PIV in wind tunnel experiments

NASA Astrophysics Data System (ADS)

Scarano, Fulvio; Ghaemi, Sina; Caridi, Giuseppe Carlo Alp; Bosbach, Johannes; Dierksheide, Uwe; Sciacchitano, Andrea

2015-02-01

The flow-tracing fidelity of sub-millimetre diameter helium-filled soap bubbles (HFSB) for low-speed aerodynamics is studied. The main interest of using HFSB in relation to micron-size droplets is the large amount of scattered light, enabling larger-scale three-dimensional experiments by tomographic PIV. The assessment of aerodynamic behaviour closely follows the method proposed in the early work of Kerho and Bragg (Exp Fluids 50:929-948, 1994) who evaluated the tracer trajectories around the stagnation region at the leading edge of an airfoil. The conclusions of the latter investigation differ from the present work, which concludes sub-millimetre HFSB do represent a valid alternative for quantitative velocimetry in wind tunnel aerodynamic experiments. The flow stagnating ahead of a circular cylinder of 25 mm diameter is considered at speeds up to 30 m/s. The tracers are injected in the free-stream and high-speed PIV, and PTV are used to obtain the velocity field distribution. A qualitative assessment based on streamlines is followed by acceleration and slip velocity measurements using PIV experiments with fog droplets as a term of reference. The tracing fidelity is controlled by the flow rates of helium, liquid soap and air in HFSB production. A characteristic time response, defined as the ratio of slip velocity and the fluid acceleration, is obtained. The feasibility of performing time-resolved tomographic PIV measurements over large volumes in aerodynamic wind tunnels is also studied. The flow past a 5-cm-diameter cylinder is measured over a volume of 20 × 20 × 12 cm3 at a rate of 2 kHz. The achieved seeding density of <0.01 ppp enables resolving the Kármán vortices, whereas turbulent sub-structures cannot be captured.

Intermittency in 2D soap film turbulence

NASA Astrophysics Data System (ADS)

Cerbus, R. T.; Goldburg, W. I.

2013-10-01

The Reynolds number dependency of intermittency for 2D turbulence is studied in a flowing soap film. The Reynolds number used here is the Taylor microscale Reynolds number Rλ, which ranges from 20 to 800. Strong intermittency is found for both the inverse energy and direct enstrophy cascades as measured by (a) the pdf of velocity differences P(δu(r)) at inertial scales r, (b) the kurtosis of P(∂xu), and (c) the scaling of the so-called intermittency exponent μ, which is zero if intermittency is absent. Measures (b) and (c) are quantitative, while (a) is qualitative. These measurements are in disagreement with some previous results but not all. The velocity derivatives are nongaussian at all Rλ but show signs of becoming gaussian as Rλ increases beyond the largest values that could be reached. The kurtosis of P(δu(r)) at various r indicates that the intermittency is scale dependent. The structure function scaling exponents also deviate strongly from the Kraichnan prediction. For the enstrophy cascade, the intermittency decreases as a power law in Rλ. This study suggests the need for a new look at the statistics of 2D turbulence.

Mother Courage and Her Soaps: "Incendies, Weeds, Nurse Jackie," and Daytime Drama

ERIC Educational Resources Information Center

Beck, Bernard

2012-01-01

The decline of the soap opera as a major form of popular culture highlights the importance of that form in creating and maintaining a shared subculture for women. Soap operas are contrasted with recent television and film works that present the struggles of women in a different way, highlighting the distinctive features of soap operas as women's…

Scanning tunneling microscopy studies of diamond films and optoelectronic materials

NASA Technical Reports Server (NTRS)

Perez, Jose M.

1993-01-01

In this report, we report on progress achieved from 12/1/92 to 10/1/93 under the grant entitled 'Scanning Tunneling Microscopy Studies of Diamond Films and Optoelectronic Materials'. We have set-up a chemical vapor deposition (CVD) diamond film growth system and a Raman spectroscopy system to study the nucleation and growth of diamond films with atomic resolution using scanning tunneling microscopy (STM). A unique feature of the diamond film growth system is that diamond films can be transferred directly to the ultrahigh vacuum (UHV) chamber of a scanning tunneling microscope without contaminating the films by exposure to air. The University of North Texas (UNT) provided $20,000 this year as matching funds for the NASA grant to purchase the diamond growth system. In addition, UNT provided a Coherent Innova 90S Argon ion laser, a Spex 1404 double spectrometer, and a Newport optical table costing $90,000 to set-up the Raman spectroscopy system. The CVD diamond growth system and Raman spectroscopy system will be used to grow and characterize diamond films with atomic resolution using STM as described in our proposal. One full-time graduate student and one full-time undergraduate student are supported under this grant. In addition, several graduate and undergraduate students were supported during the summer to assist in setting-up the diamond growth and Raman spectroscopy systems. We have obtained research results concerning STM of the structural and electronic properties of CVD grown diamond films, and STM and scanning tunneling spectroscopy of carbon nanotubes. In collaboration with the transmission electron microscopy (TEM) group at UNT, we have also obtained results concerning the optoelectronic material siloxene. These results were published in refereed scientific journals, submitted for publication, and presented as invited and contributed talks at scientific conferences.

Tunneling probe of fluctuating superconductivity in disordered thin films

NASA Astrophysics Data System (ADS)

Dentelski, David; Frydman, Aviad; Shimshoni, Efrat; Dalla Torre, Emanuele G.

2018-03-01

Disordered thin films close to the superconductor-insulator phase transition (SIT) hold the key to understanding quantum phase transition in strongly correlated materials. The SIT is governed by superconducting quantum fluctuations, which can be revealed, for example, by tunneling measurements. These experiments detect a spectral gap, accompanied by suppressed coherence peaks, on both sides of the transition. Here we describe the insulating side in terms of a fluctuating superconducting field with finite-range correlations. We perform a controlled diagrammatic resummation and derive analytic expressions for the tunneling differential conductance. We find that short-range superconducting fluctuations suppress the coherence peaks even in the presence of long-range correlations. Our approach offers a quantitative description of existing measurements on disordered thin films and accounts for tunneling spectra with suppressed coherence peaks.

Vortex wakes of a flapping foil in a flowing soap film

NASA Astrophysics Data System (ADS)

Schnipper, Teis; Andersen, Anders; Bohr, Tomas

2008-11-01

We present an experimental study of an oscillating, symmetric foil in a vertically flowing soap film. By varying frequency and amplitude of the oscillation we explore and visualize a variety of wake structures, including von Kármán wake, reverse von Kármán wake, 2P wake, and 2P+2S wake. We characterize the transition from the von Kármán wake (drag) to the reverse von Kármán wake (thrust) and discuss the results in relation to fish swimming. We visualize the time evolution of the vortex shedding in detail, identify the origins of the vortices comprising the wake, and propose a simple model to account for the transition from von Kármán like wakes to more exotic wake structures.

Thin-film metal coated insulation barrier in a Josephson tunnel junction. [Patent application

DOEpatents

Hawkins, G.A.; Clarke, J.

1975-10-31

A highly stable, durable, and reproducible Josephson tunnel junction consists of a thin-film electrode of a hard superconductor, a thin oxide insulation layer over the electrode constituting a Josephson tunnel junction barrier, a thin-film layer of stabilizing metal over the barrier, and a second thin-film hard superconductive electrode over the stabilizing film. The thin stabilizing metal film is made only thick enough to limit penetration of the electrode material through the insulation layer so as to prevent a superconductive short.

Resonant tunneling effects on cavity-embedded metal film caused by surface-plasmon excitation.

PubMed

Lan, Yung-Chiang; Chang, Che-Jung; Lee, Peng-Hsiao

2009-01-01

We investigate cavity-modulated resonant tunneling through a silver film with periodic grooves on both surfaces. A strip cavity embedded in the film affects tunneling frequencies via a coupling mode and waveguide mode. In the coupling mode, both the resonant tunneling through the gap between the groove and the cavity and the cavity itself form an entire resonant structure. In the waveguide mode, however, the cavity functions as a surface-plasmon waveguide. Hence, tunneling frequencies are close to resonant absorption frequencies of the groove structure and are irrelevant to cavity properties.

The elasticity of soap bubbles containing wormlike micelles.

PubMed

Sabadini, Edvaldo; Ungarato, Rafael F S; Miranda, Paulo B

2014-01-28

Slow-motion imaging of the rupture of soap bubbles generally shows the edges of liquid films retracting at a constant speed (known as the Taylor-Culick velocity). Here we investigate soap bubbles formed from simple solutions of a cationic surfactant (cetyltrimethylammonium bromide - CTAB) and sodium salicylate. The interaction of salicylate ions with CTAB leads to the formation of wormlike micelles (WLM), which yield a viscoelastic behavior to the liquid film of the bubble. We demonstrate that these elastic bubbles collapse at a velocity up to 30 times higher than the Taylor-Culick limit, which has never been surpassed. This is because during the bubble inflation, the entangled WLM chains stretch, storing elastic energy. This extra energy is then released during the rupture of the bubble, yielding an additional driving force for film retraction (besides surface tension). This new mechanism for the bursting of elastic bubbles may have important implications to the breakup of viscoelastic sprays in industrial applications.

Formation of soap bubbles by gas jet

NASA Astrophysics Data System (ADS)

Zhou, Maolei; Li, Min; Chen, Zhiyuan; Han, Jifeng; Liu, Dong

2017-12-01

Soap bubbles can be easily generated by various methods, while their formation process is complicated and still worth studying. A model about the bubble formation process was proposed in the study by Salkin et al. [Phys. Rev. Lett. 116, 077801 (2016)] recently, and it was reported that the bubbles were formed when the gas blowing velocity was above one threshold. However, after a detailed study of these experiments, we found that the bubbles could be generated in two velocity ranges which corresponded to the laminar and turbulent gas jet, respectively, and the predicted threshold was only effective for turbulent gas flow. The study revealed that the bubble formation was greatly influenced by the aerodynamics of the gas jet blowing to the film, and these results will help to further understand the formation mechanism of the soap bubble as well as the interaction between the gas jet and the thin liquid film.

Negative differential resistance in electron tunneling in ultrathin films near the two-dimensional limit

DOE Office of Scientific and Technical Information (OSTI.GOV)

Batabyal, R.; Abdul Wasey, A. H. M.; Mahato, J. C.

We report on our observation of negative differential resistance (NDR) in electron tunneling conductance in atomic-scale ultrathin Ag films on Si(111) substrates. NDR was observed by scanning tunneling spectroscopy measurements. The tunneling conductance depends on the electronic local density of states (LDOS) of the sample. We show that the sample bias voltage, at which negative differential resistance and peak negative conductance occur, depends on the film thickness. This can be understood from the variation in the LDOS of the Ag films as a function of film thickness down to the two-dimensional limit of one atomic layer. First principles density functionalmore » theory calculations have been used to explain the results.« less

Scanning tunneling spectroscopy of molecular thin films and semiconductor nanostructures

NASA Astrophysics Data System (ADS)

Gaan, Sandeep

Work presented in this thesis mostly deals with nano-scale study of electronic properties of organic semiconducting molecules using pentacene (Pn) as a model system and compared with various SiC surfaces to gain more insight into physical processes at nano-scale. In addition, InAs quantum dots (QDs) in a GaAs matrix are studied to probe electronic states of individual QDs. Scanning tunneling microscopy (STM) and spectroscopy (STS) are the primary experimental techniques used to probe local electronic properties on the nano-scale. Vacuum sublimated Pn thin films were deposited onto SiC substrates for STM/STS experiments. STM studies show high quality ordered Pn films. Atomic force microscopy (AFM) images reveal dendritic growth pattern of these films. Local density of states (LDOS) measurements using STS reveals a HOMO-LUMO bandgap. In order to study charge transport properties of Pn films, different amount of charge were injected into the sample by systematically changing the tip-sample separation. Saturation of the tunnel current was observed at positive sample voltages (LUMO states). This effect was attributed to a transport/space charge limitation in tunnel current by treating it as a situation analogous to charge injection into insulators which gives rise to space charge limited current (also previously observed in the case of organic semiconductors). Using a simple model we were able to derive a hopping rate that characterizes nano-scale transport in Pn films at least in the vicinity of the STM probe-tip. We have studied effect of transport limitation in the tunnel current for various semiconductor surfaces. In order to probe surfaces of varying conductivities, we have used Si-rich SiC surfaces such as 3x3 and 3x3 -R30° (both Mott-Hubbard insulators) as well as a highly conducting C-rich graphene surface, and compared those results with the data obtained from Pn. We observe variation of the decay constant kappa (which characterizes the tunneling process) on

Designation of Soap Molder Machine and Procedure for Transparent Soap

NASA Astrophysics Data System (ADS)

Mat Sharif, Zainon Binti; Taib, Norhasnina Binti Mohd; Yusof, Mohd Sallehuddin Bin; Rahim, Mohammad Zulafif Bin; Tobi, Abdul Latif Bin Mohd; Othman, Mohd Syafiq Bin

2017-05-01

Transparent soap is actually the combination of actual soap and solvent. The solvent is added into the soap solution to produce the transparent characteristic. The problem from the previous production is that tiny air bubbles were observed inside the soap resulted in less attractive appearance. Current method of producing the soap bar had taken more than 8 hours and having difficulties to take out the soap bar from the plastic mold with low production rate. It is expected that the air bubble problem can be solved using this new soup molder machine. The soap production rate is believed to increase with the invention of soap molder machine. By reducing the production time from 8 hours to 2 hours, it improve production rate significantly.

Doughnut-shaped soap bubbles.

PubMed

Préve, Deison; Saa, Alberto

2015-10-01

Soap bubbles are thin liquid films enclosing a fixed volume of air. Since the surface tension is typically assumed to be the only factor responsible for conforming the soap bubble shape, the realized bubble surfaces are always minimal area ones. Here, we consider the problem of finding the axisymmetric minimal area surface enclosing a fixed volume V and with a fixed equatorial perimeter L. It is well known that the sphere is the solution for V=L(3)/6π(2), and this is indeed the case of a free soap bubble, for instance. Surprisingly, we show that for V<αL(3)/6π(2), with α≈0.21, such a surface cannot be the usual lens-shaped surface formed by the juxtaposition of two spherical caps, but is rather a toroidal surface. Practically, a doughnut-shaped bubble is known to be ultimately unstable and, hence, it will eventually lose its axisymmetry by breaking apart in smaller bubbles. Indisputably, however, the topological transition from spherical to toroidal surfaces is mandatory here for obtaining the global solution for this axisymmetric isoperimetric problem. Our result suggests that deformed bubbles with V<αL(3)/6π(2) cannot be stable and should not exist in foams, for instance.

Doughnut-shaped soap bubbles

NASA Astrophysics Data System (ADS)

Préve, Deison; Saa, Alberto

2015-10-01

Soap bubbles are thin liquid films enclosing a fixed volume of air. Since the surface tension is typically assumed to be the only factor responsible for conforming the soap bubble shape, the realized bubble surfaces are always minimal area ones. Here, we consider the problem of finding the axisymmetric minimal area surface enclosing a fixed volume V and with a fixed equatorial perimeter L . It is well known that the sphere is the solution for V =L3/6 π2 , and this is indeed the case of a free soap bubble, for instance. Surprisingly, we show that for V <α L3/6 π2 , with α ≈0.21 , such a surface cannot be the usual lens-shaped surface formed by the juxtaposition of two spherical caps, but is rather a toroidal surface. Practically, a doughnut-shaped bubble is known to be ultimately unstable and, hence, it will eventually lose its axisymmetry by breaking apart in smaller bubbles. Indisputably, however, the topological transition from spherical to toroidal surfaces is mandatory here for obtaining the global solution for this axisymmetric isoperimetric problem. Our result suggests that deformed bubbles with V <α L3/6 π2 cannot be stable and should not exist in foams, for instance.

Videotaping the Lifespan of a Soap Bubble.

ERIC Educational Resources Information Center

Ramme, Goran

1995-01-01

Describes how the use of a videotape to record the history of a soap bubble allows a study of many interesting events in considerable detail including interference fringes, convection and turbulence patterns on the surface, formation of black film, and the ultimate explosion of the bubble. (JRH)

Scanning Tunneling Microscopy analysis of space-exposed polymer films

NASA Technical Reports Server (NTRS)

Kalil, Carol R.; Young, Philip R.

1993-01-01

The characterization of the surface of selected space-exposed polymer films by Scanning Tunneling Microscopy (STM) is reported. Principles of STM, an emerging new technique for materials analysis, are reviewed. The analysis of several films which received up to 5.8 years of low Earth orbital (LEO) exposure onboard the NASA Long Duration Exposure Facility (LDEF) is discussed. Specimens included FEP Teflon thermal blanket material, Kapton film, and several experimental polymer films. Ultraviolet and atomic oxygen-induced crazing and erosion are described. The intent of this paper is to demonstrate how STM is enhancing the understanding of LEO space environmental effects on polymer films.

On the shape of giant soap bubbles.

PubMed

Cohen, Caroline; Darbois Texier, Baptiste; Reyssat, Etienne; Snoeijer, Jacco H; Quéré, David; Clanet, Christophe

2017-03-07

We study the effect of gravity on giant soap bubbles and show that it becomes dominant above the critical size [Formula: see text], where [Formula: see text] is the mean thickness of the soap film and [Formula: see text] is the capillary length ([Formula: see text] stands for vapor-liquid surface tension, and [Formula: see text] stands for the liquid density). We first show experimentally that large soap bubbles do not retain a spherical shape but flatten when increasing their size. A theoretical model is then developed to account for this effect, predicting the shape based on mechanical equilibrium. In stark contrast to liquid drops, we show that there is no mechanical limit of the height of giant bubble shapes. In practice, the physicochemical constraints imposed by surfactant molecules limit the access to this large asymptotic domain. However, by an exact analogy, it is shown how the giant bubble shapes can be realized by large inflatable structures.

Scanning tunneling microscopy measurements of the spin Hall effect in tungsten films by using iron-coated tungsten tips

NASA Astrophysics Data System (ADS)

Xie, Ting; Dreyer, Michael; Bowen, David; Hinkel, Dan; Butera, R. E.; Krafft, Charles; Mayergoyz, Isaak

2018-05-01

Scanning tunneling microscopy experiments using iron-coated tungsten tips and current-carrying tungsten films have been conducted. An asymmetry of the tunneling current with respect to the change of the direction of the bias current through a tungsten film has been observed. It is argued that this asymmetry is a manifestation of the spin Hall effect in the current-carrying tungsten film. Nanoscale variations of this asymmetry across the tungsten film have been studied by using the scanning tunneling microscopy technique.

Electronic-Reconstruction-Enhanced Tunneling Conductance at Terrace Edges of Ultrathin Oxide Films.

PubMed

Wang, Lingfei; Kim, Rokyeon; Kim, Yoonkoo; Kim, Choong H; Hwang, Sangwoon; Cho, Myung Rae; Shin, Yeong Jae; Das, Saikat; Kim, Jeong Rae; Kalinin, Sergei V; Kim, Miyoung; Yang, Sang Mo; Noh, Tae Won

2017-11-01

Quantum mechanical tunneling of electrons across ultrathin insulating oxide barriers has been studied extensively for decades due to its great potential in electronic-device applications. In the few-nanometers-thick epitaxial oxide films, atomic-scale structural imperfections, such as the ubiquitously existed one-unit-cell-high terrace edges, can dramatically affect the tunneling probability and device performance. However, the underlying physics has not been investigated adequately. Here, taking ultrathin BaTiO 3 films as a model system, an intrinsic tunneling-conductance enhancement is reported near the terrace edges. Scanning-probe-microscopy results demonstrate the existence of highly conductive regions (tens of nanometers wide) near the terrace edges. First-principles calculations suggest that the terrace-edge geometry can trigger an electronic reconstruction, which reduces the effective tunneling barrier width locally. Furthermore, such tunneling-conductance enhancement can be discovered in other transition metal oxides and controlled by surface-termination engineering. The controllable electronic reconstruction can facilitate the implementation of oxide electronic devices and discovery of exotic low-dimensional quantum phases. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Characterization of NbN films and tunnel junctions

NASA Technical Reports Server (NTRS)

Stern, J. A.; Leduc, H. G.

1991-01-01

Properties of NbN films and NbN/MgO/NbN tunnel junctions are discussed. NbN junctions are being developed for use in high-frequency, SIS quasiparticle mixers. To properly design mixer circuits, junction and film properties need to be characterized. The specific capacitance of NbN/MgO/NbN junctions has been measured as a function of the product of the normal-state resistance and the junction area (RnA), and it is found to vary by more than a factor of two (35-85 fF/sq microns) over the range of RnA measured (1000-50 ohm sq microns). This variation is important because the specific capacitance determines the RC speed of the tunnel junction at a given RnA value. The magnetic penetration depth of NbN films deposited under different conditions is also measured. The magnetic penetration depth affects the design of microstrip line used in RF tuning circuits. Control of the magnetic penetration depth is necessary to fabricate reproducible tuning circuits. Additionally, the critical current uniformity for arrays of 100 junctions has been measured. Junction uniformity will affect the design of focal-plane arrays of SIS mixers. Finally, the relevance of these measurements to the design of Josephson electronics is discussed.

Electromagnetic properties of thin-film transformer-coupled superconducting tunnel junctions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Finnegan, T.F.; Lacquaniti, V.; Vaglio, R.

1981-09-01

Multisection superconducting microstrip transformers with designed output impedances below 0.1 ..cap omega.. have been fabricated via precise photolithographic techniques to investigate the electromagnetic properties of Nb-Nb oxide-Pb tunnel junctions. The low-impedance transformer sections incorporate a rf sputtered thin-film Ta-oxide dielectric, and the reproducible external coupling achievable with this type of geometry makes possible the systematic investigation of electromagnetic device parameters as a function of tunneling oxide thickness.

Determination of surface tension from the measurement of internal pressure of mini soap bubbles

NASA Astrophysics Data System (ADS)

Behroozi, F.; Behroozi, P. S.

2011-11-01

We review the elementary theory that gives the internal pressure of a soap bubble in terms of its radius and surface tension. The theory is generalized to relate the pressure difference across any element of a soap film to its local curvature. This result is used to introduce the concept of the mean curvature of a surface element and is applied to a double soap bubble to obtain the relation between the three radii that characterize its geometry. We also describe a simple setup, suitable for the undergraduate laboratory, to produce mini bubbles and to obtain the surface tension of the soap solution by measuring the radius and internal pressure of the bubbles.

Microbicidal effects of plain soap vs triclocarban-based antibacterial soap.

PubMed

Kim, S A; Rhee, M S

2016-11-01

The aim of this study was to determine the bactericidal effects of plain and antibacterial soap. The bactericidal effects of plain and antibacterial soap containing 0.3% triclocarban were examined against 10 Gram-positive and 10 Gram-negative bacterial strains after exposure at 22°C and 40°C for 20 s. Gram-negative bacteria were more susceptible to both soaps than Gram-positive bacteria. However, with one exception (Enterococcus faecalis ATCC 19433 at 40°C), there was no significant difference between the effects of medicated and non-medicated soap at either temperature. Triclocarban in soap does not lead to a meaningful reduction in bacterial levels during use. Copyright © 2016 The Healthcare Infection Society. Published by Elsevier Ltd. All rights reserved.

Foam soap is not as effective as liquid soap in eliminating hand microbial flora.

PubMed

Dixon, Nicolette; Morgan, Margie; Equils, Ozlem

2017-07-01

Foam soaps are aerosolized liquid soaps dispensed through a special pump mechanism. Currently there are no studies comparing liquid soap with foam soap in regard to efficacy of reducing hand microbial burden. In 3 separate experiments and with 2 different brands of foam soap, it was observed that nonantimicrobial foam soap was not as effective in reducing hand bacterial load as the liquid soap. Copyright © 2017 Association for Professionals in Infection Control and Epidemiology, Inc. Published by Elsevier Inc. All rights reserved.

Ionic channels in Langmuir-Blodgett films imaged by a scanning tunneling microscope.

PubMed Central

Kolomytkin, O V; Golubok, A O; Davydov, D N; Timofeev, V A; Vinogradova, S A; Tipisev SYa

1991-01-01

The molecular structure of channels formed by gramicidin A in a lipid membrane was imaged by a scanning tunneling microscope operating in air. The mono- and bimolecular films of lipid with gramicidin A were deposited onto a highly oriented pyrolitic graphite substrate by the Langmuir-Blodgett technique. It has been shown that under high concentration gramicidin A molecules can form in lipid films a quasi-regular, densely packed structure. Single gramicidin A molecules were imaged for the first time as well. The cavity of 0.4 +/- 0.05 nm in halfwidth was found on the scanning tunneling microscopy image of the gramicidin A molecule. The results of direct observation obtained by means of scanning tunneling microscope are in good agreement with the known molecular model of gramicidin A. It was shown that gramicidin A molecules can exist in a lipid monolayer as individual molecules or combined into clusters. The results demonstrate that scanning tunneling microscope can be used for high spatial resolution study of ionic channel structure. Images FIGURE 1 FIGURE 2 FIGURE 4 FIGURE 5 PMID:1712239

Viscous bursting of suspended films

NASA Astrophysics Data System (ADS)

Debrégeas, G.; Martin, P.; Brochard-Wyart, F.

1995-11-01

Soap films break up by an inertial process. We present here the first observations on freely suspended films of long-chain polymers, where viscous effects are dominant and no surfactant is present. A hole is nucleated at time 0 and grows up to a radius R(t) at time t. A surprising feature is that the liquid from the hole is not collected into a rim (as it is in soap films): The liquid spreads out without any significant change of the film thickness. The radius R(t) grows exponentially with time, R~exp(t/τ) [while in soap films R(t) is linear]. The rise time τ~ηe/2γ where η is viscosity, e is thickness (in the micron range), and γ is surface tension. A simple model is developed to explain this growth law.

Bubble bath soap poisoning

MedlinePlus

... medlineplus.gov/ency/article/002762.htm Bubble bath soap poisoning To use the sharing features on this page, please enable JavaScript. Bubble bath soap poisoning occurs when someone swallows bubble bath soap. ...

Do Soaps Teach Sex?

ERIC Educational Resources Information Center

Cantor, Muriel G.; Cantor, Joel M.

1984-01-01

Traces historical development of soap operas and presents results of surveys conducted with college students to determine how viewing affects their behavior, attitudes, and beliefs. Results indicate students neither seek nor take advice from soap operas whereas early radio soap opera listeners sought practical explanations of appropriate behavior…

Soap and Science.

ERIC Educational Resources Information Center

MacKinnon, Gregory R.

1998-01-01

Outlines an activity centered around the soap-making process in which soap is made via demonstration. Students are asked to develop an acid-base classification table and discuss various acid-base indicators. (DDR)

Microbial flora of in-use soap products.

PubMed Central

McBride, M E

1984-01-01

A comparison has been made of the in-use bacterial load of two bar soaps with and without antibacterials and two liquid soaps in five different locations over a 1-week period. Of the 25 samples taken from each soap, 92 to 96% of samples from bar soaps were culture positive as compared to 8% of those from liquid soaps. Bacterial populations ranged from 0 to 3.8 log CFU per sample for bar soaps and from 0 to 2.0 log CFU per sample for liquid soaps. The mean bacterial populations per sample were 1.96 and 2.47 log CFU for the two bar soaps, and 0.08 and 0.12 log CFU for the two liquid soaps. The difference in bacterial population between bar soaps and liquid soaps was statistically significant (P = 0.005). Staphylococcus aureus was isolated on three occasions from bar soaps but not from liquid soaps. S. aureus was isolated twice from the exterior of the plastic dispensers of liquid soap but not from the soap itself. Gram-negative bacteria were cultured only from soaps containing antibacterials. Bacterial populations on bar soaps were not high compared with bacterial populations on hands, and the flora was continually changing without evidence of a carrier state. PMID:6486782

Thin-film chemical sensors based on electron tunneling

NASA Technical Reports Server (NTRS)

Khanna, S. K.; Lambe, J.; Leduc, H. G.; Thakoor, A. P.

1985-01-01

The physical mechanisms underlying a novel chemical sensor based on electron tunneling in metal-insulator-metal (MIM) tunnel junctions were studied. Chemical sensors based on electron tunneling were shown to be sensitive to a variety of substances that include iodine, mercury, bismuth, ethylenedibromide, and ethylenedichloride. A sensitivity of 13 parts per billion of iodine dissolved in hexane was demonstrated. The physical mechanisms involved in the chemical sensitivity of these devices were determined to be the chemical alteration of the surface electronic structure of the top metal electrode in the MIM structure. In addition, electroreflectance spectroscopy (ERS) was studied as a complementary surface-sensitive technique. ERS was shown to be sensitive to both iodine and mercury. Electrolyte electroreflectance and solid-state MIM electroreflectance revealed qualitatively the same chemical response. A modified thin-film structure was also studied in which a chemically active layer was introduced at the top Metal-Insulator interface of the MIM devices. Cobalt phthalocyanine was used for the chemically active layer in this study. Devices modified in this way were shown to be sensitive to iodine and nitrogen dioxide. The chemical sensitivity of the modified structure was due to conductance changes in the active layer.

Liquid film demonstration experiment Skylab SL-4

NASA Technical Reports Server (NTRS)

Darbro, W.

1975-01-01

The liquid film demonstration experiment performed on Skylab 4 by Astronaut Gerald Carr, which involved the construction of water and soap films by boundary expansion and inertia, is discussed. Results include a 1-ml globule of water expanded into a 7-cm-diameter film as well as complex film structures produced by inertia whose lifetimes are longer in the low-g environment. Also discussed are 1-g acceleration experiments in which the unprovoked rupture of films was photographed and film lifetimes of stationary and rotated soap films were compared. Finally, there is a mathematical discussion regarding minimal surfaces, an isoperimetric problem, and liquid films.

Tunneling spectra and superconducting gaps observed by scanning tunneling microscopy near the grain boundaries of FeSe0.3Te0.7 films

NASA Astrophysics Data System (ADS)

Lin, K. C.; Li, Y. S.; Shen, Y. T.; Wu, M. K.; Chi, C. C.

2013-12-01

We used scanning tunneling microscopy (STM) to study the tunneling spectra of FeSe0.3Te0.7 films with two orientations of the ab-planes and a connection ramp between them. We discovered that by pulsed laser deposition (PLD) method, the a- and b-axis of the FeSe0.3Te0.7 film deposited on an Ar-ion-milled magnesium oxide (MgO) substrate were rotated 45° with respect to those of MgO, whereas the a- and b-axis of the film grown on a pristine MgO substrate were parallel to those of MgO. With photolithography and this technique, we can prepare FeSe0.3Te0.7 films with two orientations on the same MgO substrate so that the connection between them forms a ramp at an angle of about 25° to the substrate plane. In the planar region, for either the 0° or 45° orientation, we observed tunneling spectra with a superconducting gap of about 5 meV and 1.78 meV, respectively. However, a much larger gap at about 18 meV was observed in the ramp region. Furthermore, we observed a small zero-bias conductance peak (ZBCP) inside the large gap at T = 4.3 K. The ZBCP becomes smaller with increasing temperature and disappeared at temperature above 7 K.

Discovering Black Soap: A Survey on the Attitudes and Practices of Black Soap Users.

PubMed

Lin, Ann; Nabatian, Adam; Halverstam, Caroline P

2017-07-01

OBJECTIVE: The purpose of this study was to discover the general attitudes and practices of black soap users with regard to amelioration of various dermatologic conditions. DESIGN: This was a prospective questionnaire-based study with a sample size of 100 black soap users. Setting: Outpatient dermatology clinics of Montefiore Medical Center and other Albert Einstein affiliated dermatology clinics in Bronx, New York. PARTICIPANTS: One hundred subjects who have used black soap were recruited. MEASUREMENTS: The participants evaluated and reported their attitudes and applications of black soap. Data on sociodemographic prevalence and user satisfactions of black soap were collected and analyzed. RESULTS: The age distribution of participants was uniform among the specified age categories: 1) 18 to 29 years; 2) 30 to 39 years, 3) 40 to 49 yesars, and 4) 50 years and older. The sex distribution favored women, comprising 74 percent of those surveyed. A significant number of participants were born in either Africa (23%) or the Caribbean (19%). Black soap usage was applied to mitigate many dermatologic conditions, including acne (23%), dark spots (20%), razor bumps (13%), eczema (7%), and fine lines (4%). The most popular usage was for overall skin care (70%). The vast majority of users found black soap helpful for their skin condition (51% very satisfied, and 40% somewhat satisfied). Conclusion: The survey results indicate widespread usage and satisfaction with black soap for reduction in symptoms of various dermatologic conditions. Further investigations are warranted to discover active ingredients present in black soap that may unveil future therapeutic options for various dermatologic conditions.

Tunneling interferometry and measurement of the thickness of ultrathin metallic Pb(111) films

NASA Astrophysics Data System (ADS)

Ustavshchikov, S. S.; Putilov, A. V.; Aladyshkin, A. Yu.

2017-10-01

Spectra of the differential tunneling conductivity for ultrathin lead films grown on Si(111) 7 × 7 single crystals with a thickness of 9 to 50 ML have been studied by low-temperature scanning tunneling microscopy and spectroscopy. The presence of local maxima of the tunneling conductivity is characteristic of such systems. The energies of maxima of the differential conductivity are determined by the spectrum of quantum-confined states of electrons in a metallic layer and, consequently, the local thickness of the layer. It has been shown that features of the microstructure of substrates, such as steps of monatomic height, structural defects, and inclusions of other materials covered with a lead layer, can be visualized by bias-modulation scanning tunneling spectroscopy.

Laser Soap Fountain

NASA Astrophysics Data System (ADS)

Foley, Tyler; Pegram, Matthew; Jenkins, Zachary; Hester, Brooke C.; Burris, Jennifer L.

2015-01-01

We have developed an eye-catching demonstration that showcases a variety of physics topics from total internal reflection to electrostatics to non-Newtonian fluid dynamics, including the Kaye effect. The essential components of the demonstration include a vertical stream of liquid soap in which a laser pointer is internally reflected, and which subsequently hits an inclined plane. As the liquid soap, a non-Newtonian fluid, begins to accumulate into a pile, its shear properties change and the incoming fluid rebounds from the pile, forming striking parabolic arcs. We present here a readily reproducible and inexpensive version of a laser soap fountain.

Elemental and Molecular Segregation in Oil Paintings due to Lead Soap Degradation.

PubMed

Chen-Wiegart, Yu-Chen Karen; Catalano, Jaclyn; Williams, Garth J; Murphy, Anna; Yao, Yao; Zumbulyadis, Nicholas; Centeno, Silvia A; Dybowski, Cecil; Thieme, Juergen

2017-09-14

The formation of Pb, Zn, and Cu carboxylates (soaps) has caused visible deterioration in hundreds of oil paintings dating from the 15th century to the present. Through transport phenomena not yet understood, free fatty acids in the oil binding medium migrate through the paint and react with pigments containing heavy metals to form soaps. To investigate the complex correlation among the elemental segregation, types of chemical compounds formed, and possible mechanisms of the reactions, a paint sample cross-section from a 15th century oil painting was examined by synchrotron X-ray techniques. X-ray fluorescence (XRF) microscopy, quantified with elemental correlation density distribution, showed Pb and Sn segregation in the soap-affected areas. X-ray absorption near edge structure (XANES) around the Pb-L3 absorption edge showed that Pb pigments and Pb soaps can be distinguished while micro-XANES gave further information on the chemical heterogeneity in the paint film. The advantages and limitations of these synchrotron-based techniques are discussed and compared to those of methods routinely used to analyze paint samples. The results presented set the stage for improving the information extracted from samples removed from works of art and for correlating observations in model paint samples to those in the naturally aged samples, to shed light onto the mechanism of soap formation.

Elemental and Molecular Segregation in Oil Paintings due to Lead Soap Degradation

DOE PAGES

Chen-Wiegart, Yu-chen Karen; Catalano, Jaclyn; Williams, Garth J.; ...

2017-09-14

The formation of Pb, Zn, and Cu carboxylates (soaps) has caused visible deterioration in hundreds of oil paintings dating from the 15th century to the present. Through transport phenomena not yet understood, free fatty acids in the oil binding medium migrate through the paint and react with pigments containing heavy metals to form soaps. To investigate the complex correlation among the elemental segregation, types of chemical compounds formed, and possible mechanisms of the reactions, a paint sample cross-section from a 15th century oil painting was examined by synchrotron X-ray techniques. X-ray fluorescence (XRF) microscopy, quantified with elemental correlation density distribution,more » showed Pb and Sn segregation in the soap-affected areas. X-ray absorption near edge structure (XANES) around the Pb-L3 absorption edge showed that Pb pigments and Pb soaps can be distinguished while micro-XANES gave further information on the chemical heterogeneity in the paint film. The advantages and limitations of these synchrotron-based techniques are discussed and compared to those of methods routinely used to analyze paint samples. The results presented set the stage for improving the information extracted from samples removed from works of art and for correlating observations in model paint samples to those in the naturally aged samples, to shed light onto the mechanism of soap formation.« less

Elemental and Molecular Segregation in Oil Paintings due to Lead Soap Degradation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen-Wiegart, Yu-chen Karen; Catalano, Jaclyn; Williams, Garth J.

The formation of Pb, Zn, and Cu carboxylates (soaps) has caused visible deterioration in hundreds of oil paintings dating from the 15th century to the present. Through transport phenomena not yet understood, free fatty acids in the oil binding medium migrate through the paint and react with pigments containing heavy metals to form soaps. To investigate the complex correlation among the elemental segregation, types of chemical compounds formed, and possible mechanisms of the reactions, a paint sample cross-section from a 15th century oil painting was examined by synchrotron X-ray techniques. X-ray fluorescence (XRF) microscopy, quantified with elemental correlation density distribution,more » showed Pb and Sn segregation in the soap-affected areas. X-ray absorption near edge structure (XANES) around the Pb-L3 absorption edge showed that Pb pigments and Pb soaps can be distinguished while micro-XANES gave further information on the chemical heterogeneity in the paint film. The advantages and limitations of these synchrotron-based techniques are discussed and compared to those of methods routinely used to analyze paint samples. The results presented set the stage for improving the information extracted from samples removed from works of art and for correlating observations in model paint samples to those in the naturally aged samples, to shed light onto the mechanism of soap formation.« less

Plateau borders of smectic liquid crystalline films

NASA Astrophysics Data System (ADS)

Trittel, Torsten; Aldred, Ruth; Stannarius, Ralf

2011-06-01

We investigate the geometrical properties of Plateau borders in an arrangement of connected smectic A free standing films. The geometry is chosen such that a circular Plateau border surrounds a planar smectic film and connects it with two smectic catenoids. It is demonstrated that, similar to soap films, the smectic film geometry can be described by a negative line tension of the circular contact region. Thus, the equilibrium angle between the films depends upon the liquid content in this region, and with increasing liquid content, deviations from Plateau's rule are observed. The experimental results are qualitatively comparable to soap films. A possible origin of slight quantitative differences is discussed.

Magnetic tunnel junctions utilizing diamond-like carbon tunnel barriers

NASA Astrophysics Data System (ADS)

Cadieu, F. J.; Chen, Li; Li, Biao

2002-05-01

We have devised a method whereby thin particulate-free diamond-like carbon films can be made with good adhesion onto even room-temperature substrates. The method employs a filtered ionized carbon beam created by the vacuum impact of a high-energy, approximately 1 J per pulse, 248 nm excimer laser onto a carbon target. The resultant deposition beam can be steered and deflected by magnetic and electric fields to paint a specific substrate area. An important aspect of this deposition method is that the resultant films are particulate free and formed only as the result of atomic species impact. The vast majority of magnetic tunnel junctions utilizing thin metallic magnetic films have employed a thin oxidized layer of aluminum to form the tunnel barrier. This has presented reproducibility problems because the indicated optimal barrier thickness is only approximately 13 Å thick. Magnetic tunnel junctions utilizing Co and permalloy films made by evaporation and sputtering have been fabricated with an intervening diamond-like carbon tunnel barrier. The diamond-like carbon thickness profile has been tapered so that seven junctions with different barrier thickness can be formed at once. Magnetoresistive (MR) measurements made between successive permalloy strip ends include contributions from two junctions and from the permalloy and Co strips that act as current leads to the junctions. Magnetic tunnel junctions with thicker carbon barriers exhibit MR effects that are dominated by that of the permalloy strips. Since these tunnel barriers are formed without the need for oxygen, complete tunnel junctions can be formed with all high-vacuum processing.

Detecting stray microwaves and nonequilibrium quasiparticles in thin films by single-electron tunneling

NASA Astrophysics Data System (ADS)

Saira, Olli-Pentti; Maisi, Ville; Kemppinen, Antti; Möttönen, Mikko; Pekola, Jukka

2013-03-01

Superconducting thin films and tunnel junctions are the building blocks of many state-of-the-art technologies related to quantum information processing, microwave detection, and electronic amplification. These devices operate at millikelvin temperatures, and - in a naive picture - their fidelity metrics are expected to improve as the temperature is lowered. However, very often one finds in the experiment that the device performance levels off around 100-150 mK. In my presentation, I will address three common physical mechanisms that can cause such saturation: stray microwaves, nonequilibrium quasiparticles, and sub-gap quasiparticle states. The new experimental data I will present is based on a series of studies on quasiparticle transport in Coulomb-blockaded normal-insulator-superconductor tunnel junction devices. We have used a capacitively coupled SET electrometer to detect individual quasiparticle tunneling events in real time. We demonstrate the following record-low values for thin film aluminum: quasiparticle density nqp < 0 . 033 / μm3 , normalized density of sub-gap quasiparticle states (Dynes parameter) γ < 1 . 6 ×10-7 . I will also discuss some sample stage and chip designs that improve microwave shielding.

Hard Water and Soft Soap: Dependence of Soap Performance on Water Hardness

ERIC Educational Resources Information Center

Osorio, Viktoria K. L.; de Oliveira, Wanda; El Seoud, Omar A.; Cotton, Wyatt; Easdon, Jerry

2005-01-01

The demonstration of the performance of soap in different aqueous solutions, which is due to water hardness and soap formulation, is described. The demonstrations use safe, inexpensive reagents and simple glassware and equipment, introduce important everyday topics, stimulates the students to consider the wider consequences of water hardness and…

Handwashing and antiseptic-containing soaps in hospital

PubMed Central

Jarvis, J. D.; Wynne, C. D.; Enwright, L.; Williams, J. D.

1979-01-01

Two aspects of handwashing in hospital were considered. A study was carried out to examine the contamination of bar soap and containers, and the use of antiseptic soaps in reducing the resident flora of the skin. Swabs were collected from soap dishes on six wards and from a bacteriology laboratory on four consecutive days. The unmedicated bar soap was replaced by bar soap containing 2·5% povidone-iodine, and further swabs were collected over a period of seven days. Ninety-two isolates from 48 samples were obtained when unmedicated bar soap was used, and nine isolates from 42 samples when povidone-iodine (Betadine) soap was substituted. The number of organisms recovered when povidone-iodine soap was used was much reduced, and Pseudomonas spp were recovered in low numbers on only one occasion. Six laboratory workers took part in a study to compare bar soap with other agents—povidone-iodine soap, povidone-iodine surgical scrub, povidone-iodine alcoholic solution, chlorhexidine surgical scrub, and alcoholic chlorhexidine. Samples were collected after standard washes and after surgical gloves had been worn for 90 minutes. The effect of multiple washes was assessed by samples collected after six washes with the agent under study (three per day) followed by 90 minutes wearing surgical gloves. The average percentage reduction in normal flora obtained indicated that alcoholic chlorhexidine was superior to the other agents. PMID:500840

Making Usable, Quality Opaque or Transparent Soap

ERIC Educational Resources Information Center

Mabrouk, Suzanne T.

2005-01-01

The experiment to make opaque and transparent soap, using cold and semi boiled processes respectively, and surfactant tests that measure the pH of the prepared soap, is introduced. The experiment shows an easy method to make soap by giving a choice to select oils and scents for the soap, which can be used at home.

Modeling the electrostatic field localization in nanostructures based on DLC films using the tunneling microscopy methods

NASA Astrophysics Data System (ADS)

Yakunin, Alexander N.; Aban'shin, Nikolay P.; Avetisyan, Yuri A.; Akchurin, Georgy G.; Akchurin, Garif G.

2018-04-01

A model for calculating the electrostatic field in the system "probe of a tunnel microscope - a nanostructure based on a DLC film" was developed. A finite-element modeling of the localization of the field was carried out, taking into account the morphological and topological features of the nanostructure. The obtained results and their interpretation contribute to the development of the concepts to the model of tunnel electric transport processes. The possibility for effective usage of the tunneling microscopy methods in the development of new nanophotonic devices is shown.

TV watching, soap opera and happiness.

PubMed

Lu, L; Argyle, M

1993-09-01

One hundred and fourteen subjects reported the amount of time they spent watching television in general, and soap opera in particular. They also completed scales measuring happiness and other personality variables, such as extraversion and cooperativeness. In the multiple regression analysis, having controlled for the demographic variables, watching TV was related to unhappiness, whereas watching soap opera was related to happiness. Discriminant analysis showed that females, higher happiness and extraversion distinguished regular soap watchers (who nevertheless watched little TV in general) from irregular soap watchers (who nevertheless watched a lot of TV in general).

Rim instability of bursting thin smectic films

NASA Astrophysics Data System (ADS)

Trittel, Torsten; John, Thomas; Tsuji, Kinko; Stannarius, Ralf

2013-05-01

The rupture of thin smectic bubbles is studied by means of high speed video imaging. Bubbles of centimeter diameter and film thicknesses in the nanometer range are pierced, and the instabilities of the moving rim around the opening hole are described. Scaling laws describe the relation between film thickness and features of the filamentation process of the rim. A flapping motion of the retracting smectic film is assumed as the origin of the observed filamentation instability. A comparison with similar phenomena in soap bubbles is made. The present experiments extend studies on soap films [H. Lhuissier and E. Villermaux, Phys. Rev. Lett. 103, 054501 (2009), 10.1103/PhysRevLett.103.054501] to much thinner, uniform films of thermotropic liquid crystals.

Comparison of thin-film resistance heat-transfer gages with thin-skin transient calorimeter gages in conventional hypersonic wind tunnels

NASA Technical Reports Server (NTRS)

Miller, C. G., III

1981-01-01

Thin film gages deposited at the stagnation region of small (8.1-mm-diameter) hemispheres and gages mounted flush with the surface of a sharp-leading-edge flat plate were tested in the Langley continuous-flow hypersonic tunnel and in the Langley hypersonic CF4 tunnel. Two substrate materials were tested, quartz and a machinable glass-ceramic. Small hemispheres were also tested utilizing the thin-skin transient calorimeter technique usually employed in conventional tunnels. One transient calorimeter model was a thin shell of stainless steel, and the other was a thin-skin insert of stainless steel mounted into a hemisphere fabricated from a machinable-glass-ceramic. Measured heat-transfer rates from the various hemispheres were compared with one another and with predicted rates. The results demonstrate the feasibility and advantages of using-film resistance heat-transfer gages in conventional hypersonic wind tunnels over a wide range of conditions.

Soap Operas and Telenovelas: An Intercultural Critique of Soap Operas as Feminine Discourse.

ERIC Educational Resources Information Center

Lozano, Elizabeth

This paper questions some of the assumptions that permeate the current literature about soap operas and television, examining particularly the model according to which soap operas are the expression of an "essential" and universal feminine nature. The paper suggests the pertinence of a crosscultural approach to the study of melodrama as…

Molecular dynamics of palmitic acid and lead palmitate in cross-linked linseed oil films: Implications from deuterium magnetic resonance for lead soap formation in traditional oil paintings.

PubMed

Catalano, Jaclyn; Murphy, Anna; Yao, Yao; Zumbulyadis, Nicholas; Centeno, Silvia A; Dybowski, Cecil

2018-02-01

Many oil paintings, dating from the 15th century to the present, are affected by the formation of heavy-metal carboxylates (soaps) that alter the structural integrity and appearance of the works. Through transport phenomena not yet understood, free fatty acids formed from oils used as binders migrate through the paint film and react with heavy-metal ions that are constituents of pigments and/or driers, forming metal carboxylates. The local molecular dynamics of fatty acids and metal carboxylates are factors influencing material transport in these systems. We report temperature-dependent 2 H NMR spectra of palmitic acid and lead palmitate as pure materials, in cross-linked linseed oil films, and in a lead white linseed oil paint film as part of our broader research into metal soap formation. Local dynamics at the α carbon, at the terminal methyl group, and at the middle of the fatty acid chain were observed in specifically deuterated materials. Changes in the dynamic behavior with temperature were observed by the appearance of two species, a solid-like material and a liquid-like material. The relative amounts of the two phases and their deuterium NMR parameters indicate that the amount of liquid-like material and the local dynamics at that site increase with temperature. At the three locations along the chain and at all temperatures, there is a larger percentage of acyl chains of both palmitic acid and lead palmitate that are "mobile" or liquid-like in linseed oil films than there are in the pure materials. However, the percentage of liquid-like species is decreased in a lead white paint film, as compared to a linseed oil matrix. In addition, these experiments indicate that there is a larger percentage of liquid-like acyl chains of palmitic acid than of lead palmitate under identical conditions in these model paint systems. Copyright © 2017 Elsevier Inc. All rights reserved.

Tunneling rates in electron transport through double-barrier molecular junctions in a scanning tunneling microscope.

PubMed

Nazin, G V; Wu, S W; Ho, W

2005-06-21

The scanning tunneling microscope enables atomic-scale measurements of electron transport through individual molecules. Copper phthalocyanine and magnesium porphine molecules adsorbed on a thin oxide film grown on the NiAl(110) surface were probed. The single-molecule junctions contained two tunneling barriers, vacuum gap, and oxide film. Differential conductance spectroscopy shows that electron transport occurs via vibronic states of the molecules. The intensity of spectral peaks corresponding to the individual vibronic states depends on the relative electron tunneling rates through the two barriers of the junction, as found by varying the vacuum gap tunneling rate by changing the height of the scanning tunneling microscope tip above the molecule. A simple, sequential tunneling model explains the observed trends.

Medicinal and cosmetics soap production from Jatropha oil.

PubMed

Shahinuzzaman, M; Yaakob, Zahira; Moniruzzaman, M

2016-06-01

Soap is the most useful things which we use our everyday life in various cleansing and cosmetics purposes. Jatropha oil is nonedible oil which has more benefits to soap making. It has also cosmetics and medicinal properties. But the presence of toxic Phorbol esters in Jatropha oil is the main constrains to use it. So it is necessary to search a more suitable method for detoxifying the Jatropha oil before the use as the main ingredient of soap production. This review implies a more suitable method for removing phorbol esters from Jatropha oil. Several parameters such as the % yield of pure Jatropha oil soap, TFM value of soap, total alkali content, free caustic alkalinity content, pH, the antimicrobial activity, and CMC value of general soap should be taken into consideration for soap from detoxified Jatropha oil. © 2016 Wiley Periodicals, Inc.

The antimicrobial assessment of some Nigerian herbal soap.

PubMed

Igbeneghu, O A

2013-01-01

Twenty samples of herbal soaps were evaluated for their antimicrobial activity against bacteria and yeast of significance in skin infections with the aim to provide some justification for the continued use of the soaps in the management of superficial skin infections. All the soaps were found to possess antimicrobial activity in a concentration and organism dependent manner. The soaps were more active against the gram positive organisms than the Gram negative organisms while none of the soaps had activity against the tested yeasts. Only 35% of the soaps were appropriately packaged with adequate directions for use and storage. The study showed that the tested soaps possessed antimicrobial properties and they can contribute to the treatment and management of skin infections caused by bacteria if well prepared with the appropriate plant materials to target specific causative organisms and packaged with appropriate directions for use and storage.

The role of surface elasticity in liquid film formation

NASA Astrophysics Data System (ADS)

Champougny, Lorene; Scheid, Benoit; Restagno, Frederic; Rio, Emmanuelle; Laboratoire de Physique des Solides Team; TIPS-Fluid Physics Unit Team

2014-11-01

The formation of thin liquid films, either free standing (soap films) or deposited on a solid substrate (coated films), is of utmost importance for many applications, ranging from the control of foam stability to surface functionalization. In this work, the behavior of thin liquid films during their generation from a surfactant solution is investigated through comparison between a hydrodynamic model including surface elasticity and experiments. ``Twin'' models are proposed to describe the coating of films onto a solid plate (Landau-Levich-Derjaguin configuration) as well as soap film pulling (Frankel configuration) in a single framework. Experimental data are successfully fitted using the models, surface elasticity being the only adjustable parameter. For a given surfactant solution, the analyses of soap and coated films both yield the same value for the effective surface elasticity, showing that it is an intrinsic parameter of a surfactant solution. Conversely, we demonstrate that Frankel- or Landau-Levich-like experiments can be used in practice as surface rheometers to determine the numerical value of the (effective) surface elasticity of a solution, especially for values lower than those measurable by classical devices. L.C. was supported by ANR F2F. B.S. thanks the F.R.S.-FNRS for funding as well as the IAP-MicroMAST project.

Tunneling Spectroscopy of MoN and NbxTi1-xN Thin Films Grown by Atomic Layer Deposition

NASA Astrophysics Data System (ADS)

Cao, Chaoyue; Groll, Nickolas; Klug, Jeffrey; Becker, Nicholas; Altin, Serdar; Proslier, Thomas; Zasadzinski, John

2014-03-01

Tunneling I(V) and dI/dV vs. V are reported on superconducting thin films of MoN and NbxTi1-xN using a point contact method with a Au tip. The films are grown by the chemical process of atomic layer deposition (ALD) onto various substrates (Si, quartz, sapphire) held at 450 C. Resistively measured superconducting Tc values up to 12K and 13K are found for the MoN and NbxTi1-xN respectively. Artificial tunnel barriers (1-3 nm thick) of Al2O3, also grown by ALD, are shown to provide much improved tunneling characteristics compared to the native oxides. Relatively high quality gap features are observed with zero-bias conductance values as low as ~ 10% of the high bias values. Gap parameters Δ ~ 2.0meV are found for the MoN and Δ ~ 2.0-2.4 meV for the NbxTi1-xN which follow the BCS temperature dependence and close near the measured film Tc indicating bulk superconductivity at the surface. The suitability of such conformal ALD grown films for potential superconducting devices is discussed. This work was supported by the U.S. Department of Energy, Office of Science under contract No. DE-AC02-06CH11357.

National and regional assessment of the antibacterial soap market: a step toward determining the impact of prevalent antibacterial soaps.

PubMed

Perencevich, E N; Wong, M T; Harris, A D

2001-10-01

Consumer antibacterial soaps contain triclosan or triclocarban. No scientific data have been published to suggest that the use of antibacterial agents in household products prevents infection, and triclosan resistance mechanisms have recently been identified. Little data are available regarding the prevalence of antibacterial agents contained in consumer soaps. In a physician-performed survey of 23 stores in 10 states from December 1999 to April 2000, investigators determined the number of national brand liquid and bar soaps and percent of each containing antibacterial agents sold at national chain, regional grocery, and Internet stores. Antibacterial agents were present in 76% of liquid soaps and 29% of bar soaps available nationally. There were no differences found between national, regional, and Internet stores. Overall, 45% of surveyed soaps contain antibacterial agents. With limited documented benefits and experimental laboratory evidence suggesting possible adverse effects on the emergence of antimicrobial resistance, consumer antibacterial use of this magnitude should be questioned.

Tunneling rates in electron transport through double-barrier molecular junctions in a scanning tunneling microscope

PubMed Central

Nazin, G. V.; Wu, S. W.; Ho, W.

2005-01-01

The scanning tunneling microscope enables atomic-scale measurements of electron transport through individual molecules. Copper phthalocyanine and magnesium porphine molecules adsorbed on a thin oxide film grown on the NiAl(110) surface were probed. The single-molecule junctions contained two tunneling barriers, vacuum gap, and oxide film. Differential conductance spectroscopy shows that electron transport occurs via vibronic states of the molecules. The intensity of spectral peaks corresponding to the individual vibronic states depends on the relative electron tunneling rates through the two barriers of the junction, as found by varying the vacuum gap tunneling rate by changing the height of the scanning tunneling microscope tip above the molecule. A simple, sequential tunneling model explains the observed trends. PMID:15956189

Sex on the Soap Operas: Afternoon Delight.

ERIC Educational Resources Information Center

Greenberg, Bradley S.; And Others

1981-01-01

Examines the portrayal of intimate sexual behavior on soap operas and concludes that soap operas have more sexual content than do prime-time programs, but the types of intimacies differ. Notes that soap operas are potentially a major force in the transmission of values and sexual information to youthful viewers. (PD)

Tunneling Nanoelectromechanical Switches Based on Compressible Molecular Thin Films.

PubMed

Niroui, Farnaz; Wang, Annie I; Sletten, Ellen M; Song, Yi; Kong, Jing; Yablonovitch, Eli; Swager, Timothy M; Lang, Jeffrey H; Bulović, Vladimir

2015-08-25

Abrupt switching behavior and near-zero leakage current of nanoelectromechanical (NEM) switches are advantageous properties through which NEMs can outperform conventional semiconductor electrical switches. To date, however, typical NEMs structures require high actuation voltages and can prematurely fail through permanent adhesion (defined as stiction) of device components. To overcome these challenges, in the present work we propose a NEM switch, termed a "squitch," which is designed to electromechanically modulate the tunneling current through a nanometer-scale gap defined by an organic molecular film sandwiched between two electrodes. When voltage is applied across the electrodes, the generated electrostatic force compresses the sandwiched molecular layer, thereby reducing the tunneling gap and causing an exponential increase in the current through the device. The presence of the molecular layer avoids direct contact of the electrodes during the switching process. Furthermore, as the layer is compressed, the increasing surface adhesion forces are balanced by the elastic restoring force of the deformed molecules which can promote zero net stiction and recoverable switching. Through numerical analysis, we demonstrate the potential of optimizing squitch design to enable large on-off ratios beyond 6 orders of magnitude with operation in the sub-1 V regime and with nanoseconds switching times. Our preliminary experimental results based on metal-molecule-graphene devices suggest the feasibility of the proposed tunneling switching mechanism. With optimization of device design and material engineering, squitches can give rise to a broad range of low-power electronic applications.

The crossover between tunnel and hopping conductivity in granulated films of noble metals

NASA Astrophysics Data System (ADS)

Kavokin, Alexey; Kutrovskaya, Stella; Kucherik, Alexey; Osipov, Anton; Vartanyan, Tigran; Arakelyan, Sergey

2017-11-01

The conductivity of thin films composed by clusters of gold and silver nanoparticles has been studies in a wide range of temperatures. The switch from a temperature independence to an exponential thermal dependence of the conductivity manifests the crossover between the tunnel and thermally activated hopping regimes of the electronic transport at the temperature of 60 °C. The characteristic thermal activation energy that governs hopping of electrons between nanoparticles is estimated as 1.3 eV. We have achieved a good control of the composition and thicknesses of nano-cluster films by use of the laser ablation method in colloidal solutions.

Time-Dependent ATR-FTIR Spectroscopic Studies on Fatty Acid Diffusion and the Formation of Metal Soaps in Oil Paint Model Systems.

PubMed

Baij, Lambert; Hermans, Joen J; Keune, Katrien; Iedema, Piet

2018-06-18

The formation of metal soaps (metal complexes of saturated fatty acids) is a serious problem affecting the appearance and structural integrity of many oil paintings. Tailored model systems for aged oil paint and time-dependent attenuated total reflection Fourier transform infrared (ATR-FTIR) spectroscopy were used to study the diffusion of palmitic acid and subsequent metal soap crystallization. The simultaneous presence of free saturated fatty acids and polymer-bound metal carboxylates leads to rapid metal soap crystallization, following a complex mechanism that involves both acid and metal diffusion. Solvent flow, water, and pigments all enhance metal soap crystallization in the model systems. These results contribute to the development of paint cleaning strategies, a better understanding of oil paint degradation, and highlight the potential of time-dependent ATR-FTIR spectroscopy for studying dynamic processes in polymer films. © 2018 The Authors. Published by Wiley-VCH Verlag GmbH & Co. KGaA.

Charge storage and tunneling mechanism of Ni nanocrystals embedded HfOx film

NASA Astrophysics Data System (ADS)

Zhu, H. X.; Zhang, T.; Wang, R. X.; Zhang, Y. Y.; Li, L. T.; Qiu, X. Y.

2016-05-01

A nano-floating gate memory structure based on Ni nanocrystals (NCs) embedded HfOx film is deposited by means of radio-frequency magnetron sputtering. Microstructure investigations reveal that self-organized Ni-NCs with diameters of 4-8 nm are well dispersed in amorphous HfOx matrix. Pt/Ni-NCs embedded HfOx/Si/Ag capacitor structures exhibit voltage-dependent capacitance-voltage hysteresis, and a maximum flat-band voltage shift of 1.5 V, corresponding to a charge storage density of 6.0 × 1012 electrons/cm2, is achieved. These capacitor memory cells exhibit good endurance characteristic up to 4 × 104 cycles and excellent retention performance of 105 s, fulfilling the requirements of next generation non-volatile memory devices. Schottky tunneling is proven to be responsible for electrons tunneling in these capacitors.

Spectroscopic and Thermal Behavior of Chromium Soaps

NASA Astrophysics Data System (ADS)

Mehrotra, K. N.; Jain, Mamta

1996-02-01

The physicochemical characteristics of chromium soaps (myristate and stearate) were investigated in the solid state (thermal, X-ray, and IR measurements) and in solutions (spectrophotometric measurements). The thermal measurements showed that the decomposition of chromium soaps is a two-step process. The soap decomposed into chromium oxycarboxylate, ketone, and carbon dioxide in the first step and the intermediate oxycarboxylate underwent further decomposition to chromium trioxide in the second step. The results showed that the second step is kinetically of zero order and the values of energy of activation for the first and second steps lie in the ranges 6-7 and 17-18 kcal mol-1, respectively. The X-ray diffraction results showed that these soaps possess double-layer structure with molecular axes slightly inclined to the basal plane. The infrared results revealed that the fatty acids exist with dimeric structure through hydrogen bonding between two molecules of fatty acids whereas the metal-to-oxygen bonds in chromium soaps are not purely ionic but possess considerable covalent character. The results of spectrophotometric measurements also confirmed the somewhat covalent nature of chromium soaps in solutions in dichloromethane.

Soap Gets in Your Eyes

PubMed Central

Laidlaw, Alistair; Bloom, Philip

1990-01-01

We present a previously unreported series of five cases of acute angle closure glaucoma associated with watching the Australia soap opera "Neighbours". Two cases were bilateral and associated with watching two episodes of "Neighbours" on the same day. The pathogenesis, and possible role of watching soap operas in the causation of primary angle closure glaucoma is discussed. PMID:1369543

THE GERMICIDAL AND HEMOLYTIC ACTION OF α-BROM SOAPS

PubMed Central

Eggerth, Arnold H.

1929-01-01

1. The soaps of the α-brom fatty acids are usually more germicidal than the unsubstituted soaps. Only when B. typhosus was the test organism was there no increase in germicidal action. 2. For any test organism, germicidal action of the brominated soaps increases rapidly with increasing molecular weight up to a certain point, then diminishes. This is likewise true of the hemolytic titer. The point of maximal germicidal action varies with the different species of tests organisms. In the series studied, brominated soaps of 12 and 14 carbon atoms were most germicidal for the Gram-negative organisms, while soaps of 16 and 18 carbon atoms were most germicidal for Gram-positive organisms. 3. The brominated soaps are, in general, more active in acid that in neutral or alkaline reactions. The reasons for this have been discussed in a previous paper, in which a similar phenomenon with unsubstituted soaps was observed. 4. For certain organisms, the brominated soaps are among the most rapid and potent germicides known. PMID:19869537

Soaps and Detergents--A 'Social' Treatment.

ERIC Educational Resources Information Center

Rust, S. C.

1979-01-01

Describes how social aspects of science can be incorporated into teaching soap and detergents in British secondary chemistry and general science courses. Historical background to the use and production of soap and the development of detergents are also presented. (HM)

Stability conditions and mechanism of cream soaps: role of glycerol.

PubMed

Sagitani, Hiromichi

2014-01-01

Fatty acids, fatty acid potassium soaps, glycerol and water are essential ingredients in the production of stable cream soaps. In this study, the behavior of these components in solution was investigated to elucidate the stability conditions and mechanism of cream soaps. It was determined that the cream soaps were a dispersion of 1:1 acid soap (1:1 molar ratio of potassium soap/fatty acid) crystals in the lamellar gel phase, which has confirmed from the phase behavior diagrams and small angle X-ray scattering data. Glycerol was crucial ingredient in the formation of the lamellar gel phase. The cleansing process of the cream soaps was also evaluated using the same diagrams. The structure of the continuous phase in cream soaps changed from lamellar gel to a micellar aqueous solution upon the addition of water. This structural change during the washing process is important in producing the foaming activity of acid soaps to wash away dirt or excess fats from the skin surface.

Chronicles of foam films.

PubMed

Gochev, G; Platikanov, D; Miller, R

2016-07-01

The history of the scientific research on foam films, traditionally known as soap films, dates back to as early as the late 17th century when Boyle and Hooke paid special attention to the colours of soap bubbles. Their inspiration was transferred to Newton, who began systematic study of the science of foam films. Over the next centuries, a number of scientists dealt with the open questions of the drainage, stability and thickness of foam films. The significant contributions of Plateau and Gibbs in the middle/late 19th century are particularly recognized. After the "colours" method of Newton, Reinold and Rücker as well as Johhonnot developed optical methods for measuring the thickness of the thinner "non-colour" films (first order black) that are still in use today. At the beginning of the 20th century, various aspects of the foam film science were elucidated by the works of Dewar and Perrin and later by Mysels. Undoubtedly, the introduction of the disjoining pressure by Derjaguin and the manifestation of the DLVO theory in describing the film stability are considered as milestones in the theoretical development of foam films. The study of foam films gained momentum with the introduction of the microscopic foam film methodology by Scheludko and Exerowa, which is widely used today. This historical perspective serves as a guide through the chronological development of knowledge on foam films achieved over several centuries. Copyright © 2015 Elsevier B.V. All rights reserved.

Bacterial flora of commonly used soaps in three hospitals in Nigeria.

PubMed

Afolabi, B A; Oduyebo, O O; Ogunsola, F T

2007-10-01

To obtain general information on soap use and soap bacterial flora, and to assess the risk of transmission of organisms from contaminated soap to patients. Descriptive study. Three hospitals in an urban area of Lagos, Nigeria. A teaching (761 bed) hospital, a general hospital (a 51 bed secondary healthcare facility) and a private hospital (a 30 bed private community with a surgical specialty). Bar soaps were much more commonly used than liquid soaps. Out of the thirty six bar soaps and their receptacles studied, 19 (52.8%) were found wet, nine (25%) dry, five (13.9%) very dry, and three (8.3%) in a pool of water. A total of 39% soaps and 75% of receptacles were contaminated. Thirty three percent of the dry soaps and 68.4% of the wet soaps were contaminated. None of the very dry soaps and all in a pool of water were contaminated. The bacteria isolated from soaps included Pseudomonas aeruginosa (89.5%) and Klebsiella pneumoniae (10.5%), while Pseudomonas aeruginosa (70.6%), Klebsiella pneumoniae (14.7%), Staphylococcus aureus (11.8%) and Serratia marcescens (2.9%) were isolated from the receptacles. The antibiogram showed that the Pseudomonas aeruginosa isolated from the soaps and their containers (sinks) were distinct from those obtained from colonised or infected wounds. The soap contamination rates correlated with the conditions in which the soaps were kept. The type of soap containers in particular, played a vital role in keeping the soap dry or wet. In all the hospitals studied, the policies on soap use, if any, were not in agreement with the recommended guidelines. The healthcare workers need to be re-educated on these guidelines.

Drag reduction in hydrocarbon-aluminum soap polymer systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zakin, J.L.; Lee, K.C.

1972-01-01

While the drag-reducing capability of solutions of aluminum soap in hydrocarbons in turbulent flow has been known for over 20 yr, investigations of the effects of concentration, soap type, and aging on drag reduction have only recently begun. The effects of aging, shear stress, and the presence of peptizers on drag reduction of hydrocarbon dispersions of aluminum soaps at relatively low concentrations were studied. These systems showed an apparent upper critical shear stress above which drag reduction was gradually lost. Degradation of the soap micelle structure occurred relatively rapidly above this point and recovery was slow. The effect of peptizersmore » is complex. In some situations, it enhanced and in others reduced the drag-reducing ability of the soap polymers. (13 refs.)« less

Consumer antibacterial soaps: effective or just risky?

PubMed

Aiello, Allison E; Larson, Elaine L; Levy, Stuart B

2007-09-01

Much has been written recently about the potential hazards versus benefits of antibacterial (biocide)-containing soaps. The purpose of this systematic literature review was to assess the studies that have examined the efficacy of products containing triclosan, compared with that of plain soap, in the community setting, as well as to evaluate findings that address potential hazards of this use--namely, the emergence of antibiotic-resistant bacteria. The PubMed database was searched for English-language articles, using relevant keyword combinations for articles published between 1980 and 2006. Twenty-seven studies were eventually identified as being relevant to the review. Soaps containing triclosan within the range of concentrations commonly used in the community setting (0.1%-0.45% wt/vol) were no more effective than plain soap at preventing infectious illness symptoms and reducing bacterial levels on the hands. Several laboratory studies demonstrated evidence of triclosan-adapted cross-resistance to antibiotics among different species of bacteria. The lack of an additional health benefit associated with the use of triclosan-containing consumer soaps over regular soap, coupled with laboratory data demonstrating a potential risk of selecting for drug resistance, warrants further evaluation by governmental regulators regarding antibacterial product claims and advertising. Further studies of this issue are encouraged.

Soaps and detergents: understanding their composition and effect.

PubMed

Kirsner, R S; Froelich, C W

1998-03-01

Soaps have been used for thousands of years as part of religious ceremonies and daily life. Derived from fatty acids or triglycerides (fats or oils) into their alkali derivatives through a process called saponification, soaps are important for healthcare professionals in preventing the spread of disease. Partly due to their alkaline nature, soaps are limited by their irritancy to the skin and their tendency to form insoluble and inactive salts when combined with either hard water or sea water. Therefore, soap alternatives or synthetic detergents have been developed. Detergents are classified into four groups: anionic, cationic, amphoteric, and non-ionic. These four groups are based on the hydrophilic qualities and surfactants they possess. Each group has characteristics that pertain to its main uses, irritancy, and toxicity. Understanding soaps and detergents may assist clinicians in making intelligent choices when using these agents on their patients as either skin cleansers or wound cleansers. Understanding the characteristics of soaps and detergents is especially important when dealing with at-risk patients such as the elderly.

Fabrication and Characterization of ZnO Langmuir-Blodgett Film and Its Use in Metal-Insulator-Metal Tunnel Diode.

PubMed

Azad, Ibrahim; Ram, Manoj K; Goswami, D Yogi; Stefanakos, Elias

2016-08-23

Metal-insulator-metal tunnel diodes have great potential for use in infrared detection and energy harvesting applications. The quantum based tunneling mechanism of electrons in MIM (metal-insulator-metal) or MIIM (metal-insulator-insulator-metal) diodes can facilitate rectification at THz frequencies. In this study, the required nanometer thin insulating layer (I) in the MIM diode structure was fabricated using the Langmuir-Blodgett technique. The zinc stearate LB film was deposited on Au/Cr coated quartz, FTO, and silicon substrates, and then heat treated by varying the temperature from 100 to 550 °C to obtain nanometer thin ZnO layers. The thin films were characterized by XRD, AFM, FTIR, and cyclic voltammetry methods. The final MIM structure was fabricated by depositing chromium/nickel over the ZnO on Au/Cr film. The current voltage (I-V) characteristics of the diode showed that the conduction mechanism is electron tunneling through the thin insulating layer. The sensitivity of the diodes was as high as 32 V(-1). The diode resistance was ∼80 Ω (at a bias voltage of 0.78 V), and the rectification ratio at that bias point was about 12 (for a voltage swing of ±200 mV). The diode response exhibited significant nonlinearity and high asymmetry at the bias point, very desirable diode performance parameters for IR detection applications.

Soap Operas and Sexual Activity: A Decade Later.

ERIC Educational Resources Information Center

Greenberg, Bradley S.; Busselle, Rick W.

1996-01-01

Finds that soap operas analyzed in 1994 contain more frequent sexual incidence on an hourly average, both within the same soaps analyzed a decade earlier and even more so on two additional very popular soaps. Shows that the more frequent sex centers on physical intercourse, primarily among partners not married to anyone; and sexual activity is…

Profiling the Adolescent Soap Opera Viewer.

ERIC Educational Resources Information Center

Alexander, Alison; And Others

Observing that plot and character changes in the daytime television serials has increased the teen and preteen share of soap opera audiences, a study compared demographic, personal experience, and attitudinal variables among adolescent soap opera fans, occasional viewers, and nonviewers. Data were collected from 230 students in the classrooms of…

Presentation Extensions of the SOAP

NASA Technical Reports Server (NTRS)

Carnright, Robert; Stodden, David; Coggi, John

2009-01-01

A set of extensions of the Satellite Orbit Analysis Program (SOAP) enables simultaneous and/or sequential presentation of information from multiple sources. SOAP is used in the aerospace community as a means of collaborative visualization and analysis of data on planned spacecraft missions. The following definitions of terms also describe the display modalities of SOAP as now extended: In SOAP terminology, View signifies an animated three-dimensional (3D) scene, two-dimensional still image, plot of numerical data, or any other visible display derived from a computational simulation or other data source; a) "Viewport" signifies a rectangular portion of a computer-display window containing a view; b) "Palette" signifies a collection of one or more viewports configured for simultaneous (split-screen) display in the same window; c) "Slide" signifies a palette with a beginning and ending time and an animation time step; and d) "Presentation" signifies a prescribed sequence of slides. For example, multiple 3D views from different locations can be crafted for simultaneous display and combined with numerical plots and other representations of data for both qualitative and quantitative analysis. The resulting sets of views can be temporally sequenced to convey visual impressions of a sequence of events for a planned mission.

Influence of Soap Characteristics and Food Service Facility Type on the Degree of Bacterial Contamination of Open, Refillable Bulk Soaps.

PubMed

Schaffner, Donald W; Jensen, Dane; Gerba, Charles P; Shumaker, David; Arbogast, James W

2018-02-01

Concern has been raised regarding the public health risks from refillable bulk-soap dispensers because they provide an environment for potentially pathogenic bacteria to grow. This study surveyed the microbial quality of open refillable bulk soap in four different food establishment types in three states. Two hundred ninety-six samples of bulk soap were collected from food service establishments in Arizona, New Jersey, and Ohio. Samples were tested for total heterotrophic viable bacteria, Pseudomonas, coliforms and Escherichia coli, and Salmonella. Bacteria were screened for antibiotic resistance. The pH, solids content, and water activity of all soap samples were measured. Samples were assayed for the presence of the common antibacterial agents triclosan and parachlorometaxylenol. More than 85% of the soap samples tested contained no detectable microorganisms, but when a sample contained any detectable microorganisms, it was most likely contaminated at a very high level (∼7 log CFU/mL). Microorganisms detected in contaminated soap included Klebsiella oxytoca, Serratia liquefaciens, Shigella sonnei, Enterobacter gergoviae, Serratia odorifera, and Enterobacter cloacae. Twenty-three samples contained antibiotic-resistant organisms, some of which were resistant to two or more antibiotics. Every sample containing less than 4% solids had some detectable level of bacteria, whereas no samples with greater than 14% solids had detectable bacteria. This finding suggests the use of dilution and/or low-cost formulations as a cause of bacterial growth. There was a statistically significant difference ( P = 0.0035) between the fraction of bacteria-positive samples with no detected antimicrobial agent (17%) and those containing an antimicrobial agent (7%). Fast food operations and grocery stores were more likely to have detectable bacteria in bulk-soap samples compared with convenience stores ( P < 0.05). Our findings underscore the risk to public health from use of refillable

The Tunnels of Samos

NASA Technical Reports Server (NTRS)

Apostol, Tom M. (Editor)

1995-01-01

This 'Project Mathematics' series video from CalTech presents the tunnel of Samos, a famous underground aquaduct tunnel located near the capital of Pithagorion (named after the famed Greek mathematician, Pythagoras, who lived there), on one of the Greek islands. This tunnel was constructed around 600 BC by King Samos and was built under a nearby mountain. Through film footage and computer animation, the mathematical principles and concepts of why and how this aquaduct tunnel was built are explained.

Surface and protective properties of dispersions of film-formers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Turishcheva, R.A.; Bakaleinikov, M.B.; Minkina, E.N.

1983-03-01

This article reports on studies of the surface and protective properties of 20% dispersions of film-formers most typically used in film-forming inhibited petroleum-base compositions (FIPC): solid hydrocarbons, fatty acid soaps, asphalt, polymers, natural resins, modified vegetable oils, and an inorganic thickening agent. Investigates the dispersions of Butosil and lithium stearate at respective concentrations of 10% and 8%, in view of the high thickening power of these film-formers. Classifies all of the studied FIPC film-forming components into 2 groups: those wth little thickening effect, a low level of adhesion-cohesion interaction, and a high level of surface and protective properties (the oxidizedmore » solid hydrocarbons and the polymers); and the film-formers that have a large thickening effect, a high level of adhesion-cohesion interaction, and a low level of surface and protective properties (the fatty acid soaps, the solid hydrocarbons, and Butosil). Recommends combining film-formers of both groups in developing new grades of FIPCs.« less

Social uses of commercial soap operas: a conversation with Miguel Sabido.

PubMed

Singhal, A; Obregon, R

1999-01-01

This paper presents an interview with Miguel Sabido, a writer-producer-director of theater and soap operas in Mexico concerning the social uses of commercial soap operas. According to Sabido, television soap operas can play multiple roles in educating the public: 1) melodramatic soap operas represent a mediation between good and bad; 2) soap operas allow people to gossip on different characters, their dilemmas, and create a climate for social change, especially if it centers on key social issues; and 3) soap operas provide role models to emulate. Sabido stressed the importance of a theory-based method for producing drama and mentioned how theoreticians Bentley, Bandura, Maclean, and Jung influenced his writing and production of soap operas. According to Sabido, the social uses of commercial television are possible with socially responsible soap operas.

Building an automated SOAP classifier for emergency department reports.

PubMed

Mowery, Danielle; Wiebe, Janyce; Visweswaran, Shyam; Harkema, Henk; Chapman, Wendy W

2012-02-01

Information extraction applications that extract structured event and entity information from unstructured text can leverage knowledge of clinical report structure to improve performance. The Subjective, Objective, Assessment, Plan (SOAP) framework, used to structure progress notes to facilitate problem-specific, clinical decision making by physicians, is one example of a well-known, canonical structure in the medical domain. Although its applicability to structuring data is understood, its contribution to information extraction tasks has not yet been determined. The first step to evaluating the SOAP framework's usefulness for clinical information extraction is to apply the model to clinical narratives and develop an automated SOAP classifier that classifies sentences from clinical reports. In this quantitative study, we applied the SOAP framework to sentences from emergency department reports, and trained and evaluated SOAP classifiers built with various linguistic features. We found the SOAP framework can be applied manually to emergency department reports with high agreement (Cohen's kappa coefficients over 0.70). Using a variety of features, we found classifiers for each SOAP class can be created with moderate to outstanding performance with F(1) scores of 93.9 (subjective), 94.5 (objective), 75.7 (assessment), and 77.0 (plan). We look forward to expanding the framework and applying the SOAP classification to clinical information extraction tasks. Copyright © 2011. Published by Elsevier Inc.

Manual dexterity aptitude testing: a soap carving study.

PubMed

Tang, Christopher G; Hilsinger, Raymond L; Cruz, Raul M; Schloegel, Luke J; Byl, Fred M; Rasgon, Barry M

2014-03-01

Currently there are few validated metrics for predicting surgical skill among otolaryngology residency applicants. To determine whether manual dexterity aptitude testing in the form of soap carving during otolaryngology residency interviews at Kaiser Permanente Medical Center Oakland predicts surgical skill at the time of graduation from otolaryngology residency programs. This study was conducted to determine how applicants with the best and worst soap carvings compared at the time of graduation with respect to various metrics including visuospatial ability and manual dexterity. Over the last 25 years, applicants to the residency program at Kaiser Permanente Oakland were required to carve soap during their residency interview. The 3 best and 3 worst soap carvings from 1990 through 2006 were determined. Of the individuals who carved those soaps, 62 qualified for the study and matriculated into otolaryngology residency programs. Surveys were sent to the 62 individuals' residency programs to evaluate those individuals on a 5-point Likert scale in various categories as well as to rank those individuals as being in the top 50% or bottom 50% of their graduating class. All else being equal, we hypothesized that applicants who had the manual dexterity and visuospatial skills to accurately carve a bar of soap would more likely possess the skills necessary to become a good surgeon. There was no difference between individuals with the best soap carvings and those with the worst soap carvings in all categories: cognitive knowledge, visuospatial ability, manual dexterity, decision making, and overall score (P > .10 for all categories). There was a 95% response rate, with 35 of 37 residency programs responding and 59 of 62 surveys returned. Manual dexterity aptitude testing in the form of soap carving does not appear to correlate with surgical skill at the time of graduation. Further studies need to be conducted to determine the role of manual dexterity and visuospatial

Evaluation and remediation of bulk soap dispensers for biofilm.

PubMed

Lorenz, Lindsey A; Ramsay, Bradley D; Goeres, Darla M; Fields, Matthew W; Zapka, Carrie A; Macinga, David R

2012-01-01

Recent studies evaluating bulk soap in public restroom soap dispensers have demonstrated up to 25% of open refillable bulk-soap dispensers were contaminated with ~ 6 log(10)(CFU ml(-1)) heterotrophic bacteria. In this study, plastic counter-mounted, plastic wall-mounted and stainless steel wall-mounted dispensers were analyzed for suspended and biofilm bacteria using total cell and viable plate counts. Independent of dispenser type or construction material, the bulk soap was contaminated with 4-7 log(10)(CFU ml(-1)) bacteria, while 4-6 log(10)(CFU cm(-2)) biofilm bacteria were isolated from the inside surfaces of the dispensers (n = 6). Dispenser remediation studies, including a 10 min soak with 5000 mg l(-1) sodium hypochlorite, were then conducted to determine the efficacy of cleaning and disinfectant procedures against established biofilms. The testing showed that contamination of the bulk soap returned to pre-test levels within 7-14 days. These results demonstrate biofilm is present in contaminated bulk-soap dispensers and remediation studies to clean and sanitize the dispensers are temporary.

Probing Dirac fermion dynamics in topological insulator Bi2Se3 films with a scanning tunneling microscope.

PubMed

Song, Can-Li; Wang, Lili; He, Ke; Ji, Shuai-Hua; Chen, Xi; Ma, Xu-Cun; Xue, Qi-Kun

2015-05-01

Scanning tunneling microscopy and spectroscopy have been used to investigate the femtosecond dynamics of Dirac fermions in the topological insulator Bi2Se3 ultrathin films. At the two-dimensional limit, bulk electrons become quantized and the quantization can be controlled by the film thickness at a single quintuple layer level. By studying the spatial decay of standing waves (quasiparticle interference patterns) off steps, we measure directly the energy and film thickness dependence of the phase relaxation length lϕ and inelastic scattering lifetime τ of topological surface-state electrons. We find that τ exhibits a remarkable (E - EF)(-2) energy dependence and increases with film thickness. We show that the features revealed are typical for electron-electron scattering between surface and bulk states.

The importance of soap selection for routine hand hygiene in hospital.

PubMed Central

Ojajärvi, J.

1981-01-01

Five different types of liquid soap were studied in hospital wards, each during two months' use. Altogether 1306 finger print samples were taken from the hands of the staff by sampling twice a week and the acceptability of the soaps was measured by a questionnaire. During the use of different soaps only slight differences were found in the numbers of total bacteria or in the occurrence of Staph. aureus and gram-negative bacilli on the hands. During the use of the emulsion-type product studied, several persons who had dermatological problems had lower mean bacterial counts of the fingers than during the use of the other soaps. This soap was also favourably accepted by the staff. After over one year's use of pine oil soap and alcohol, the staff of the hospital was satisfied with the method. However, several persons with skin problems admitted to not using soap or alcohol. The considerable differences found in the acceptability of soaps imply that for use in hospital the choice of a soap acceptable to the nursing staff is important in promoting proper hand hygiene. PMID:7240731

Critical assessment of the pH of children's soap.

PubMed

Mendes, Bruna Rafaela; Shimabukuro, Danielle Midori; Uber, Marjorie; Abagge, Kerstin Taniguchi

2016-01-01

To evaluate the pH value of children's antibacterial soaps and syndets used in children's baths and verify whether there is information regarding pH on the product label. Quantitative, cross-sectional, analytical observational study that included ninety soap samples, both in bar and liquid presentations, as follows: 67 children's soap (group 1), 17 antibacterial soaps (group 2), and 6 syndets (group 3). Each sample had its pH measured after 1% dilution. In addition to descriptive statistics, the Pearson-Yates chi-squared test and Student's t-tests were applied, considering the minimal significance level of 5%. The Wilcoxon-Mann-Whitney test, Fisher's exact test, and the Kruskal-Wallis test were used for inferential statistics. The pH levels varied considerably between liquid and bar presentations, with lower levels (4.4-7.9) found for the liquids (p<0.05). Syndets showed pH levels close to the ideal (slightly acid) and the antibacterial soaps showed the highest pH levels (up to 11.34) (p<0.05). Only two of the soaps included in the study had information about their pH levels on the product packaging. Knowledge of the pH of children's soap by doctors and users is important, considering the great pH variability found in this study. Moreover, liquid soaps, and especially syndets, are the most recommended for the sensitive skin of neonates and infants, in order to guarantee skin barrier efficacy. Copyright © 2016 Sociedade Brasileira de Pediatria. Published by Elsevier Editora Ltda. All rights reserved.

Data Integration Using SOAP in the VSO

NASA Astrophysics Data System (ADS)

Tian, K. Q.; Bogart, R. S.; Davey, A.; Dimitoglou, G.; Gurman, J. B.; Hill, F.; Martens, P. C.; Wampler, S.

2003-05-01

The Virtual Solar Observatory (VSO) project has implemented a time interval search for all four participating data archives. The back-end query services are implemented as web services, and are accessible via SOAP. SOAP (Simple Object Access Protocol) defines an RPC (Remote Procedure Call) mechanism that employs HTTP as its transport and encodes the client-server interactions (request and response messages) in XML (eXtensible Markup Language) documents. In addition to its core function of identifying relevant datasets in the local archive, the SOAP server at each data provider acts as a "wrapper" that maps descriptions in an abstract data model to those in the provider-specific data model, and vice versa. It is in this way that VSO integrates heterogeneous data services and allows access to them using a common interface. Our experience with SOAP has been fruitful. It has proven to be a better alternative to traditional web access methods, namely POST and GET, because of its flexibility and interoperability.

Synthesis of Exotic Soaps in the Chemistry Laboratory

NASA Astrophysics Data System (ADS)

Phanstiel, Otto, IV; Dueno, Eric; Xianghong Wang, Queenie

1998-05-01

A variety of different triglyceride sources ranging from Vietnamese garlic oil to a local restaurant's grill sludge were saponified to generate a series of exotic soaps. Students did not quantify their results, but described their products in terms of color, texture and odor. Their results were compared with existing data on the triglyceride content for each source used (when possible). Soap texture seemed to be related to the degree of unsaturation present in the starting triglyceride. However, texture alterations due to occluded impurities could not be ruled out. In general, fats and oils high in saturated fats (butter) gave hard, chunky, and waxlike soaps, while those high in unsaturated fats gave flaky and easily crumbled soaps (olive, corn, peanut and sunflower oils). Soap color was not consistent with triglyceride unsaturation levels during the time frame studied. Odor changes were dramatic and were explained in terms of a change in chemical structure (i.e. conversion from an ester to a carboxylate salt). In general, the experiment was well received by students and stressed the importance of making precise qualitative observations during the experiment.

Bactericidal effects of triclosan in soap both in vitro and in vivo.

PubMed

Kim, S A; Moon, H; Lee, K; Rhee, M S

2015-12-01

On December 2013, the US FDA proposed a rule stating that manufacturers must provide data to demonstrate that antibacterial soap is more effective than plain soap or water. The objective of the present study was to examine the in vitro and in vivo bactericidal effect of triclosan (the most widely used antiseptic agent in soap) in soap. Twenty bacterial strains (proposed by the FDA) were exposed to plain and antibacterial soaps (the same formulation as plain soap, but containing 0.3% triclosan) for 20 s at 22°C (room temperature) and 40°C (warm temperature). The temperature and time were selected to simulate the hand washing conditions and procedures used by consumers. The triclosan concentration of 0.3% is the maximum allowed by law. The decontamination efficacy of plain soap and antibacterial soap was also examined in vivo: the hands of volunteers were artificially inoculated with Serratia marcescens. There was no significant difference (P > 0.05) in bactericidal activity between plain soap and antibacterial soap at either test temperature. However, antibacterial soap showed significantly greater bactericidal effects after 9 h. These results suggest that although triclosan-containing soap does have antibacterial activity, the effects are not apparent during the short time required for hand washing. Antibacterial soap containing triclosan (0.3%) was no more effective than plain soap at reducing bacterial contamination when used under 'real-life' conditions. The present study provides practical information that may prove useful for both industry and governments. © The Author 2015. Published by Oxford University Press on behalf of the British Society for Antimicrobial Chemotherapy. All rights reserved. For Permissions, please e-mail: journals.permissions@oup.com.

Opening and retraction of particulate soap films

NASA Astrophysics Data System (ADS)

Timounay, Yousra; Lorenceau, Elise; Rouyer, Florence

2015-07-01

We study for the first time the bursting dynamics of thin liquid films laden with hydrophobic micronic particles either with free or constrained edges. We highlight that the particles can arrange in bilayer or monolayer configurations and explore a range of particles coverage from zero to random close packing. When the particles bridge the two interfaces (monolayer configuration) of free-edge films, the hole opens intermittently. For the other cases, we observe constant retraction velocities, modeled by balancing liquid and particles inertia against surface tension as in Taylor-Culick theory. But, this approach is only valid up to a critical value of particles coverage due to the interplay between the interfaces and the friction between particles.

Significance of Ca-soap formation for calcium absorption in the rat.

PubMed Central

Gacs, G; Barltrop, D

1977-01-01

The significance of calcium soap formation in the inhibition of calcium absorption has been studied in rats. 47Ca labelled soaps of fatty acids were introduced into the duodenum and the absorption of calcium measured after four hours in a whole body counter. The absorption of calcium was inversely correlated with the chain length of the fatty acid varying from 1% for Ca-stearate to 60% for Ca-hexanoate. Increasing the degree of unsaturation of the fatty acid was accompanied by increased calcium absorption. The availability of calcium for absorption from the soaps was correlated with their solubility in 1% aqueous Na-tauroglycocholate. The percentages of calcium as soap in the small intestine and the faeces after intragastric administration of calcium and fats were similar, which suggests that the faecal content of calcium soaps is an index of intestinal soap formation. Soap formation was negligible when CaCl2 was given with tristearate, triolaeate, or tridecanoate and no depression of calcium absorption was observed. Calcium absorption was markedly impaired by the addition of phosphates at a Ca/P ratio of 1:1 irrespective of the presence of neutral fats. Stearic acid resulted in significant soap formation and reduced calcium absorption. The degree of Ca-soap formation and the inhibition of calcium absorption were well correlated. The results suggest that, although calcium soap formation may markedly depress calcium absorption in the rat, no significant soap formation takes place when fats are given in the form of triglycerides. PMID:838405

Electrical conduction of organic ultrathin films evaluated by an independently driven double-tip scanning tunneling microscope.

PubMed

Takami, K; Tsuruta, S; Miyake, Y; Akai-Kasaya, M; Saito, A; Aono, M; Kuwahara, Y

2011-11-02

The electrical transport properties of organic thin films within the micrometer scale have been evaluated by a laboratory-built independently driven double-tip scanning tunneling microscope, operating under ambient conditions. The two tips were used as point contact electrodes, and current in the range from 0.1 pA to 100 nA flowing between the two tips through the material can be detected. We demonstrated two-dimensional contour mapping of the electrical resistance on a poly(3-octylthiophene) thin films as shown below. The obtained contour map clearly provided an image of two-dimensional electrical conductance between two point electrodes on the poly(3-octylthiophene) thin film. The conductivity of the thin film was estimated to be (1-8) × 10(-6) S cm(-1). Future prospects and the desired development of multiprobe STMs are also discussed.

Sensitivities of Soap Solutions in Leak Detection

NASA Technical Reports Server (NTRS)

Stuck, D.; Lam, D. Q.; Daniels, C.

1985-01-01

Document describes method for determining minimum leak rate to which soap-solution leak detectors sensitive. Bubbles formed at smaller leak rates than previously assumed. In addition to presenting test results, document discusses effects of joint-flange configurations, properties of soap solutions, and correlation of test results with earlier data.

Imaging the electron-boson coupling in superconducting FeSe films using a scanning tunneling microscope.

PubMed

Song, Can-Li; Wang, Yi-Lin; Jiang, Ye-Ping; Li, Zhi; Wang, Lili; He, Ke; Chen, Xi; Hoffman, Jennifer E; Ma, Xu-Cun; Xue, Qi-Kun

2014-02-07

Scanning tunneling spectroscopy has been used to reveal signatures of a bosonic mode in the local quasiparticle density of states of superconducting FeSe films. The mode appears below Tc as a "dip-hump" feature at energy Ω∼4.7kBTc beyond the superconducting gap Δ. Spectra on strained regions of the FeSe films reveal simultaneous decreases in Δ and Ω. This contrasts with all previous reports on other high-Tc superconductors, where Δ locally anticorrelates with Ω. A local strong coupling model is found to reconcile the discrepancy well, and to provide a unified picture of the electron-boson coupling in unconventional superconductors.

Effect of an Interfacial Layer on Electron Tunneling through Atomically Thin Al2O3 Tunnel Barriers.

PubMed

Wilt, Jamie; Sakidja, Ridwan; Goul, Ryan; Wu, Judy Z

2017-10-25

Electron tunneling through high-quality, atomically thin dielectric films can provide a critical enabling technology for future microelectronics, bringing enhanced quantum coherent transport, fast speed, small size, and high energy efficiency. A fundamental challenge is in controlling the interface between the dielectric and device electrodes. An interfacial layer (IL) will contain defects and introduce defects in the dielectric film grown atop, preventing electron tunneling through the formation of shorts. In this work, we present the first systematic investigation of the IL in Al 2 O 3 dielectric films of 1-6 Å's in thickness on an Al electrode. We integrated several advanced approaches: molecular dynamics to simulate IL formation, in situ high vacuum sputtering atomic layer deposition (ALD) to synthesize Al 2 O 3 on Al films, and in situ ultrahigh vacuum scanning tunneling spectroscopy to probe the electron tunneling through the Al 2 O 3 . The IL had a profound effect on electron tunneling. We observed a reduced tunnel barrier height and soft-type dielectric breakdown which indicate that defects are present in both the IL and in the Al 2 O 3 . The IL forms primarily due to exposure of the Al to trace O 2 and/or H 2 O during the pre-ALD heating step of fabrication. As the IL was systematically reduced, by controlling the pre-ALD sample heating, we observed an increase of the ALD Al 2 O 3 barrier height from 0.9 to 1.5 eV along with a transition from soft to hard dielectric breakdown. This work represents a key step toward the realization of high-quality, atomically thin dielectrics with electron tunneling for the next generation of microelectronics.

Stability Conditions and Mechanism of Cream Soaps: Effect of Polyols.

PubMed

Sagitani, Hiromichi; Komoriya, Masumi

2015-01-01

Fatty acids, fatty acid potassium soaps, polyols and water are essential ingredients for producing stable cream soaps. The solution behavior of the above four components system has been studied to elucidate the effect of four sorts of polyols (glycerol, 1,3-butylene glycol, polyethylene glycol 400 and dipropylene glycol) on the stability of cream soaps. It has been revealed that the lamellar liquid crystalline one-phase converted to a two-phase of a lamellar phase and an isotropic aqueous solution by the addition of a few percent of 1,3-butylene glycol, polyethylene glycol 400 and dipropylene glycol, whereas the lamellar one-phase was remained by about 50 wt% of glycerol in the aqueous solution. The X-ray data at room temperature showed that the existence of 1:1 acid soap (1:1 mole ratio of potassium soap/fatty acid) crystals in the 1,3-butylene glycol, polyethylene glycol 400 and dipropylene glycol systems, whereas that the coexistence of 1:1 acid soap crystal and a lamellar gel phase (swelled lamellar gel structure) in the glycerol system. The phase transition peaks from coagel to gel (Tgel) and from gel to liquid state (Tc) were appeared in the above four polyol systems by DSC measurements. It was confirmed from the combined data of SAXS and DSC that the existence of anhydrous 1:1 acid soap gels (or with small amount of bound water) in the all polyol systems, whereas the coexistence of the anhydrate gel and the swelled gel with a lot of intermediate water in the only glycerol system. This swelled gel structure would be contributed to stabilize the dispersed anhydrate acid soap crystals in cream soaps.

Scanning Tunneling Microscopy Studies of Diamond Films and Optoelectronic Materials

NASA Technical Reports Server (NTRS)

Perez, Jose M.

1996-01-01

We present a summary of the research, citations of publications resulting from the research and abstracts of such publications. We have made no inventions in the performance of the work in this project. The main goals of the project were to set up a Chemical Vapor Deposition (CVD) diamond growth system attached to an UltraHigh Vacuum (UHV) atomic resolution Scanning Tunneling Microscopy (STM) system and carry out experiments aimed at studying the properties and growth of diamond films using atomic resolution UHV STM. We successfully achieved these goals. We observed, for the first time, the atomic structure of the surface of CVD grown epitaxial diamond (100) films using UHV STM. We studied the effects of atomic hydrogen on the CVD diamond growth process. We studied the electronic properties of the diamond (100) (2x1) surface, and the effect of alkali metal adsorbates such as Cs on the work function of this surface using UHV STM spectroscopy techniques. We also studied, using STM, new electronic materials such as carbon nanotubes and gold nanostructures. This work resulted in four publications in refereed scientific journals and five publications in refereed conference proceedings.

Colorful Demos with a Long-Lasting Soap Bubble.

ERIC Educational Resources Information Center

Behroozi, F.; Olson, D. W.

1994-01-01

Describes several demonstrations that feature interaction of light with soap bubbles. Includes directions about how to produce a long-lasting stationary soap bubble with an easily changeable size and describes the interaction of white light with the bubble. (DDR)

Pro-development soap operas: a novel approach to development communication.

PubMed

Brown, W J; Singhal, A; Rogers, E M

1989-01-01

Soap operas have their roots in 18th century English romance novels. These evolved into serialized radio dramas. In their current form, they were developed primarily to attract large audiences in order to sell consumer products. Hence the name soap which refers to the soap manufacturers who commonly advertise on such programs. In the world of soap operas there are 2 kinds. Those that function primarily to entertain and sell consumer products, and those that primarily entertain, but infuse positive social messages. The former are found everywhere, but are the only kind in America. The latter are found exclusively in developing countries. American soap operas have conveyed pro-social messages in the past, but they differ fundamentally from pro-development soap operas in their theoretical foundations. American soap operas are created by people who want to sell consumer goods. Development soap operas are created by people who want to convey pro-social messages that will aid their country's development. Both must be popular in order to be successful, but the former lack moral coherency, are unrealistic, erode values, and are created through a process of a theoretical development; while the latter have moral coherency, are realistic, promote values, and are created through a process of theoretical development. The 1st pro-development soap opera was Ven Conmigo (Come With Me) and was produced in Mexico between 1975-76. Its primary purpose was to increase adult literacy. During the year it ran, applicants at adult literacy centers rose by 600,000 or 63% compared to 7% the year before, and 2% the year after. The 2nd pro-development soap opera was Acompaname (Accompany Me) and it primary purpose was to promote family planning. It ran from 1977-78 and during that time the number of family planning adopters rose by 560,000 and contraceptive sale sin Mexico rose sharply. The question of what are pro-social messages and who should control them must be answered by each country in

Between soap bubbles and vesicles: The dynamics of freely floating smectic bubbles

NASA Astrophysics Data System (ADS)

Stannarius, Ralf; May, Kathrin; Harth, Kirsten; Trittel, Torsten

2013-03-01

The dynamics of droplets and bubbles, particularly on microscopic scales, are of considerable importance in biological, environmental, and technical contexts. We introduce freely floating bubbles of smectic liquid crystals and report their unique dynamic properties. Smectic bubbles can be used as simple models for dynamic studies of fluid membranes. In equilibrium, they form minimal surfaces like soap films. However, shape transformations of closed smectic membranes that change the surface area involve the formation and motion of molecular layer dislocations. These processes are slow compared to the capillary wave dynamics, therefore the effective surface tension is zero like in vesicles. Freely floating smectic bubbles are prepared from collapsing catenoid films and their dynamics is studied with optical high-speed imaging. Experiments are performed under normal gravity and in microgravity during parabolic flights. Supported by DLR within grant OASIS-Co.

Chemistry in Soap Bubbles.

ERIC Educational Resources Information Center

Lee, Albert W. M.; Wong, A.; Lee, H. W.; Lee, H. Y.; Zhou, Ning-Huai

2002-01-01

Describes a laboratory experiment in which common chemical gases are trapped inside soap bubbles. Examines the physical and chemical properties of the gases such as relative density and combustion. (Author/MM)

Thermal conductivity of thin insulating films determined by tunnel magneto-Seebeck effect measurements and finite-element modeling

NASA Astrophysics Data System (ADS)

Huebner, Torsten; Martens, Ulrike; Walowski, Jakob; Münzenberg, Markus; Thomas, Andy; Reiss, Günter; Kuschel, Timo

2018-06-01

In general, it is difficult to access the thermal conductivity of thin insulating films experimentally by electrical means. Here, we present a new approach utilizing the tunnel magneto-Seebeck effect (TMS) in combination with finite-element modeling (FEM). We detect the laser-induced TMS and the absolute thermovoltage of laser-heated magnetic tunnel junctions with 2.6 nm thin barriers of MgAl2O4 (MAO) and MgO, respectively. A second measurement of the absolute thermovoltage after a dielectric breakdown of the barrier grants insight into the remaining thermovoltage of the stack. Thus, the pure TMS without any parasitic Nernst contributions from the leads can be identified. In combination with FEM via COMSOL, we are able to extract values for the thermal conductivity of MAO (0.7 W (K · m)‑1) and MgO (5.8 W (K · m)‑1), which are in very good agreement with theoretical predictions. Our method provides a new promising way to extract the experimentally challenging parameter of the thermal conductivity of thin insulating films.

Scanning tunneling microscopy, orbital-mediated tunneling spectroscopy, and ultraviolet photoelectron spectroscopy of metal(II) tetraphenylporphyrins deposited from vapor.

PubMed

Scudiero, L; Barlow, D E; Mazur, U; Hipps, K W

2001-05-02

Thin films of vapor-deposited Ni(II) and Co(II) complexes of tetraphenylporphyrin (NiTPP and CoTPP) were studied supported on gold and embedded in Al-Al(2)O(3)-MTPP-Pb tunnel diodes, where M = Ni or Co. Thin films deposited onto polycrystalline gold were analyzed by ultraviolet photoelectron spectroscopy (UPS) using He I radiation. Scanning tunneling microscopy (STM) and orbital-mediated tunneling spectroscopy (STM-OMTS) were performed on submonolayer films of CoTPP and NiTPP supported on Au(111). Inelastic electron tunneling spectroscopy (IETS) and OMTS were measured in conventional tunnel diode structures. The highest occupied pi molecular orbital of the porphyrin ring was seen in both STM-OMTS and UPS at about 6.4 eV below the vacuum level. The lowest unoccupied pi molecular orbital of the porphyrin ring was observed by STM-OMTS and by IETS-OMTS to be located near 3.4 eV below the vacuum level. The OMTS spectra of CoTPP had a band near 5.2 eV (below the vacuum level) that was attributed to transient oxidation of the central Co(II) ion. That is, it is due to electron OMT via the half-filled d(z)(2) orbital present in Co(II) of CoTPP. The NiTPP OMTS spectra show no such band, consistent with the known difficulty of oxidation of the Ni(II) ion. The STM-based OMTS allowed these two porphyrin complexes to be easily distinguished. The present work is the first report of the observation of STM-OMTS, tunnel junction OMTS, and UPS of the same compounds. Scanning tunneling microscope-based orbital-mediated tunneling provides more information than UPS or tunnel junction-based OMTS and does so with molecular-scale resolution.

The Systems SOAP Note: A Systems Learning Tool.

PubMed

Mitsuishi, Fumi; Young, John Q; Leary, Mark; Dilley, James; Mangurian, Christina

2016-02-01

Systems-based practice (SBP) is the only Accreditation Council for Graduate Medical Education (ACGME) competency concerned with public health and is relatively neglected in residency curricula. A tool was developed and pilot-tested to improve SBP learning on inpatient psychiatry rotations. A four-step approach was used: (1) literature review, (2) expert consultation, (3) tool development, and (4) pilot testing on four cases and evaluation for completion time and preliminary efficacy. Out of 51 SBP articles, six (12%) focused on psychiatric residency programs, and none had a practical SBP learning tool. The "systems SOAP (subjective, objective, assessment, plan) note" (S-SOAP) was structured after a clinical SOAP note and was easy to use (mean completion time = 60 min), and residents self-reported more insight into systems issues. The S-SOAP tool was effectively integrated into clinical experience and provided insight into systemic complexities. Future research should assess SBP knowledge acquisition after the use of such tools.

Health: the soap opera version.

PubMed

Harris, C

1993-01-01

Watching soap opera is a favorite pastime of millions of Egyptians. Since the spring of 1992, the soap opera "The Family House" has reached audiences with messages on AIDS, drugs, child spacing, home accidents, and hygiene. The shows are the brainchild of the Director of the Center for Development Communication (CDC) in Egypt, Dr. El Kamel; the shows capture the novel and unique concept of both the communication of information and entertainment. Between 1983 and 1990, the CDC has been creating 130 short soap opera episodes on subjects such as the prevention of dehydration from diarrhea and the use of oral rehydration salt (ORS) packets to save children's lives. The ORS episodes were 15 minutes in length and showed the dramatic tension between a baby suffering from diarrhea and the mother's helping to overcome the difficulty. Surveys conducted in 1983 and 1986 on knowledge, attitudes, and practices found that in 1986 98% knew about ORS and 70% had used it compared with 3% knowledge and 50% practice in 1983. "The Family House" will be similar but expand on the number of issues considered and will pretest audience knowledge, attitudes, and practice before and after airing on specific issues. This soap opera also will be the first to be a daily series with an unending story. "The main character is Amina, who is an artisan in her late 40s who raised 4 children by herself." The series of 45-minute long shows will depict urban and rural settings and everyday Egyptian culture: language, clothing, life styles, and moral standards. Distribution is anticipated for other Arabic countries in Africa and the Middle East, which already air many Egyptian television series.

Probing individual tunneling fluctuators with coherently controlled tunneling systems

NASA Astrophysics Data System (ADS)

Meißner, Saskia M.; Seiler, Arnold; Lisenfeld, Jürgen; Ustinov, Alexey V.; Weiss, Georg

2018-05-01

Josephson junctions made from aluminum and its oxide are the most commonly used functional elements for superconducting circuits and qubits. It is generally known that the disordered thin film AlOx contains atomic tunneling systems. Coherent tunneling systems may couple strongly to a qubit via their electric dipole moment, giving rise to spectral level repulsion. In addition, slowly fluctuating tunneling systems are observable when they are located close to coherent ones and distort their potentials. This interaction causes telegraphic switching of the coherent tunneling systems' energy splitting. Here, we measure such switching induced by individual fluctuators on timescales from hours to minutes using a superconducting qubit as a detector. Moreover, we extend the range of measurable switching times to millisecond scales by employing a highly sensitive single-photon qubit swap spectroscopy and statistical analysis of the measured qubit states.

The essential SOAP note in an EHR age.

PubMed

Pearce, Patricia F; Ferguson, Laurie Anne; George, Gwen S; Langford, Cynthia A

2016-02-18

This article reviews the traditional Subjective, Objective, Assessment, and Plan (SOAP) note documentation format. The information in the SOAP note is useful to both providers and students for history taking and physical exam, and highlights the importance of including critical documentation details with or without an electronic health record.

Nosocomial Serratia marcescens infections associated with extrinsic contamination of a liquid nonmedicated soap.

PubMed

Sartor, C; Jacomo, V; Duvivier, C; Tissot-Dupont, H; Sambuc, R; Drancourt, M

2000-03-01

To determine the role of nonmedicated soap as a source of Serratia marcescens nosocomial infections (NIs) in hospital units with endemic S marcescens NI and to examine the mechanisms of soap colonization. University-affiliated tertiary-care hospitals. A prospective case-control study and an environmental investigation were performed to assess the relationship between S marcescens NIs in hospital units and S marcescens-contaminated soap. Soap-bottle use and handwashing practices were reviewed. Cultures of healthcare workers' (HCWs) hands were obtained before and after hand washing with soap. 5 of 7 hospital units with S marcescens NIs had soap bottles contaminated with S marcescens, compared to 1 of 14 other units (P=.006). After hand washing with an S marcescens-contaminated soap pump, HCWs' hands were 54 times more likely to be contaminated with S marcescens (P<.001). Extrinsic contamination of a non-medicated liquid soap by S marcescens resulted in handborne transmission of S marcescens NIs by HCWs in our setting. This finding led to the application of strict guidelines for nonmedicated soap use and to the reinforcement of alcoholic hand disinfection.

A low energy muon spin rotation and point contact tunneling study of niobium films prepared for superconducting cavities

NASA Astrophysics Data System (ADS)

Junginger, Tobias; Calatroni, S.; Sublet, A.; Terenziani, G.; Prokscha, T.; Salman, Z.; Suter, A.; Proslier, T.; Zasadzinski, J.

2017-12-01

Point contact tunneling and low energy muon spin rotation are used to probe, on the same samples, the surface superconducting properties of micrometer thick niobium films deposited onto copper substrates using different sputtering techniques: diode, dc magnetron and HIPIMS. The combined results are compared to radio-frequency tests performances of RF cavities made with the same processes. Degraded surface superconducting properties are found to correlate to lower quality factors and stronger Q-slope. In addition, both techniques find evidence for surface paramagnetism on all samples and particularly on Nb films prepared by HIPIMS.

Laser Soap Fountain

ERIC Educational Resources Information Center

Foley, Tyler; Pegram, Matthew; Jenkins, Zachary; Hester, Brooke C.; Burris, Jennifer L.

2015-01-01

We have developed an eye-catching demonstration that showcases a variety of physics topics from total internal reflection to electrostatics to non-Newtonian fluid dynamics, including the Kaye effect. The essential components of the demonstration include a vertical stream of liquid soap in which a laser pointer is internally reflected, and which…

Quantitative assessment of risk reduction from hand washing with antibacterial soaps.

PubMed

Gibson, L L; Rose, J B; Haas, C N; Gerba, C P; Rusin, P A

2002-01-01

The Centers for Disease Control and Prevention have estimated that there are 3,713,000 cases of infectious disease associated with day care facilities each year. The objective of this study was to examine the risk reduction achieved from using different soap formulations after diaper changing using a microbial quantitative risk assessment approach. To achieve this, a probability of infection model and an exposure assessment based on micro-organism transfer were used to evaluate the efficacy of different soap formulations in reducing the probability of disease following hand contact with an enteric pathogen. Based on this model, it was determined that the probability of infection ranged from 24/100 to 91/100 for those changing diapers of babies with symptomatic shigellosis who used a control product (soap without an antibacterial ingredient), 22/100 to 91/100 for those who used an antibacterial soap (chlorohexadine 4%), and 15/100 to 90/100 for those who used a triclosan (1.5%) antibacterial soap. Those with asymptomatic shigellosis who used a non-antibacterial control soap had a risk between 49/100,000 and 53/100, those who used the 4% chlorohexadine-containing soap had a risk between 43/100,000 and 51/100, and for those who used a 1.5% triclosan soap had a risk between 21/100,000 and 43/100. The adequate washing of hands after diapering reduces risk and can be further reduced by a factor of 20% by the use of an antibacterial soap. Quantitative risk assessment is a valuable tool in the evaluation of household sanitizing agents and low risk outcomes.

Ecological effects of a deodorant and a plain soap upon human skin bacteria.

PubMed Central

Bibel, D. J.

1977-01-01

The effects of a commercial trichlorocarbanilide-containing deodorant soap and a commercial plain soap upon the cutaneous flora of individuals were compared. Using a cross-over design, 21 volunteers (10 women and 11 men) washed their forearms at least once a day with one soap for 3 weeks and then switched soaps for another 4 weeks use. By analysis of variance no significant difference in total colony counts was noted among individuals in their use of the two soaps. With the exception of individual variation, neither sequence of use, sex, nor any combination was influential. However, in 20 of 21 subjects an alteration in the composition of skin flora was observed. The deodorant soap, which in six cases increased total flora, tended to reduce or eliminate diphtheroids in 12 to 17 carriers (71%). Fewer kinds of bacteria were also noted. More Staphylococcus epidermidis was seen with the plain soap, but washing with the deodorant soap seemed to favour Acinetobacter calcoaceticus and Micrococcus luteus. The impact of this alteration and the use of total counts to measure effectiveness of deodorant soaps were brought into question. PMID:264493

Washing with contaminated bar soap is unlikely to transfer bacteria.

PubMed Central

Heinze, J. E.; Yackovich, F.

1988-01-01

Recent reports of the isolation of microorganisms from used soap bars have raised the concern that bacteria may be transferred from contaminated soap bars during handwashing. Since only one study addressing this question has been published, we developed an additional procedure to test this concern. In our new method prewashed and softened commercial deodorant soap bars (0.8% triclocarban) not active against Gram-negative bacteria were inoculated with Escherichia coli and Pseudomonas aeruginosa to give mean total survival levels of 4.4 X 10(5) c.f.u. per bar which was 70-fold higher than those reported on used soap bars. Sixteen panelists were instructed to wash with the inoculated bars using their normal handwashing procedure. After washing, none of the 16 panelists had detectable levels of either test bacterium on their hands. Thus, the results obtained using our new method were in complete agreement with those obtained with the previously published method even though the two methods differ in a number of procedural aspects. These findings, along with other published reports, show that little hazard exists in routine handwashing with previously used soap bars and support the frequent use of soap and water for handwashing to prevent the spread of disease. PMID:3402545

Bacterial hand contamination and transfer after use of contaminated bulk-soap-refillable dispensers.

PubMed

Zapka, Carrie A; Campbell, Esther J; Maxwell, Sheri L; Gerba, Charles P; Dolan, Michael J; Arbogast, James W; Macinga, David R

2011-05-01

Bulk-soap-refillable dispensers are prone to extrinsic bacterial contamination, and recent studies demonstrated that approximately one in four dispensers in public restrooms are contaminated. The purpose of this study was to quantify bacterial hand contamination and transfer after use of contaminated soap under controlled laboratory and in-use conditions in a community setting. Under laboratory conditions using liquid soap experimentally contaminated with 7.51 log(10) CFU/ml of Serratia marcescens, an average of 5.28 log(10) CFU remained on each hand after washing, and 2.23 log(10) CFU was transferred to an agar surface. In an elementary-school-based field study, Gram-negative bacteria on the hands of students and staff increased by 1.42 log(10) CFU per hand (26-fold) after washing with soap from contaminated bulk-soap-refillable dispensers. In contrast, washing with soap from dispensers with sealed refills significantly reduced bacteria on hands by 0.30 log(10) CFU per hand (2-fold). Additionally, the mean number of Gram-negative bacteria transferred to surfaces after washing with soap from dispensers with sealed-soap refills (0.06 log(10) CFU) was significantly lower than the mean number after washing with contaminated bulk-soap-refillable dispensers (0.74 log(10) CFU; P < 0.01). Finally, significantly higher levels of Gram-negative bacteria were recovered from students (2.82 log(10) CFU per hand) than were recovered from staff (2.22 log(10) CFU per hand) after washing with contaminated bulk soap (P < 0.01). These results demonstrate that washing with contaminated soap from bulk-soap-refillable dispensers can increase the number of opportunistic pathogens on the hands and may play a role in the transmission of bacteria in public settings.

Transport Properties of Thin Bismuth Films on InP (110) Surfaces by Scanning Tunneling Potentiometry

NASA Astrophysics Data System (ADS)

Feenstra, R. M.; Briner, B. G.; Chin, T. P.; Woodall, J. M.

1996-03-01

Charge transport in 20--30 Å thick Bi-films is studied by scanning tunneling potentiometry (STP) at room temperature. The Bi is deposited on cleaved InP(110) surfaces at temperatures near 140 K, yielding atomically flat films interspersed with 12 Å deep holes. The InP substrates contain conducting/insulating/conducting layers, which in cross-section are used to form contacts to the film, thus enabling lateral current densities as high as 8 × 10^6 A/cm^2 . Potential variations due to scattering of this lateral current is detected using STP, by locating the zero-crossing of current-voltage characteristics at each pixel in an image. Potential images reveal, on a coarse scale, a smooth ramp arising from the electric field due to phonon scattering in the film, from which an electron-phonon scattering length of >1000 Å is deduced. On a finer scale, potential steps 2--10 mV high are seen near surface holes and grain boundaries in the film. Detailed study of the ballistic scattering near the holes reveals a dipole shaped feature, which is identified as a residual resistivity dipole. *present address: Physics, Carnegie Mellon Univ., Pittsburgh PA 15213 **now at: Fritz-Haber-Institut, 14195 Berlin, briner@fhi-berlin.mpg.de

Mild soaps and radiotherapy: a survey of the UK public to identify brands of soap considered mild and analysis of these to ascertain suitability for recommendation in radiotherapy departments.

PubMed

Robertson, K; Brown, P

2011-05-01

Cancer agencies recommend that patients use mild soap when undergoing external beam radiotherapy to minimise skin reactions. They define 'mild soap' as non-alkaline, lanolin free, unperfumed soap with a neutral pH. This study aimed to identify which soaps the UK public perceive as mild and ascertain if these were clinically mild and could potentially be recommended within radiotherapy departments. A survey of 237 participants identified eight top brands of mild soap, which were then tested for pH and analysed for potential irritants. All soaps were lanolin free and non-alkaline, with Simple and Johnson's the closest to pH 5.5. All contained fragrances except Simple and E45. Dove, Pears and Imperial Leather contained the highest concentration of fragrances. All soaps except E45 contained potential irritants. Only Simple and E45 fit the cancer agencies' definition of mild soap and could therefore be recommended for radiotherapy patients. Future research should identify current practices and recommendations in the UK as anecdotal evidence suggests large variations in skin care advice. Further scientific analysis could potentially identify cheaper brands that fit the definition of 'mild'. UK recommendations should be standardised and consistent with best practice to reduce skin reaction severity in radiotherapy patients. © 2010 Blackwell Publishing Ltd.

9. 5TH FLOOR, INTERIOR DETAIL TO EAST OF SOAP BIN ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

9. 5TH FLOOR, INTERIOR DETAIL TO EAST OF SOAP BIN No. 4: UPPER SCREWS MOVED SOAP CHIPS HORIZONTALLY FROM BIN TO BIN; LOWER LEFT-AND RIGHT-HAND SCREWS MOVED CHIPS TO CHUTE LEADING TO 3RD FLOOR SOAP MILLS - Colgate & Company Jersey City Plant, Building No. B-14, 54-58 Grand Street, Jersey City, Hudson County, NJ

Hydrodynamics experiments with soap films and soap bubbles: A short review of recent experiments

NASA Astrophysics Data System (ADS)

Kellay, H.

2017-11-01

In this short review, I focus on recent experiments that benefit from the advantages offered by the two-dimensionality of the flow in suspended thin liquid films to reconsider hydrodynamics problems which have resisted a full understanding. The first problem discussed here concerns friction drag in channel flows. The use of turbulent channel flows, using thin liquid films, allows measurements of friction drag as well as mean velocity profiles for flows with different spectral exponents. Is there a link between the spectral properties of the turbulence and the mean velocity profiles or the frictional drag? This is the first question considered. The second issue examined considers the long time dynamics of large scale vortices. These are obtained in half bubbles rendered "turbulent" through thermal convection. These vortices, which live in a quasi two-dimensional environment, have a long time dynamics where their vorticity goes through what seems to be a well-defined cycle with generic features.

Process for direct integration of a thin-film silicon p-n junction diode with a magnetic tunnel junction

DOEpatents

Toet, Daniel; Sigmon, Thomas W.

2004-12-07

A process for direct integration of a thin-film silicon p-n junction diode with a magnetic tunnel junction for use in advanced magnetic random access memory (MRAM) cells for high performance, non-volatile memory arrays. The process is based on pulsed laser processing for the fabrication of vertical polycrystalline silicon electronic device structures, in particular p-n junction diodes, on films of metals deposited onto low temperature-substrates such as ceramics, dielectrics, glass, or polymers. The process preserves underlayers and structures onto which the devices are typically deposited, such as silicon integrated circuits. The process involves the low temperature deposition of at least one layer of silicon, either in an amorphous or a polycrystalline phase on a metal layer. Dopants may be introduced in the silicon film during or after deposition. The film is then irradiated with short pulse laser energy that is efficiently absorbed in the silicon, which results in the crystallization of the film and simultaneously in the activation of the dopants via ultrafast melting and solidification. The silicon film can be patterned either before or after crystallization.

Process For Direct Integration Of A Thin-Film Silicon P-N Junction Diode With A Magnetic Tunnel Junction

DOEpatents

Toet, Daniel; Sigmon, Thomas W.

2005-08-23

A process for direct integration of a thin-film silicon p-n junction diode with a magnetic tunnel junction for use in advanced magnetic random access memory (MRAM) cells for high performance, non-volatile memory arrays. The process is based on pulsed laser processing for the fabrication of vertical polycrystalline silicon electronic device structures, in particular p-n junction diodes, on films of metals deposited onto low temperature-substrates such as ceramics, dielectrics, glass, or polymers. The process preserves underlayers and structures onto which the devices are typically deposited, such as silicon integrated circuits. The process involves the low temperature deposition of at least one layer of silicon, either in an amorphous or a polycrystalline phase on a metal layer. Dopants may be introduced in the silicon film during or after deposition. The film is then irradiated with short pulse laser energy that is efficiently absorbed in the silicon, which results in the crystallization of the film and simultaneously in the activation of the dopants via ultrafast melting and solidification. The silicon film can be patterned either before or after crystallization.

Process for direct integration of a thin-film silicon p-n junction diode with a magnetic tunnel junction

DOEpatents

Toet, Daniel; Sigmon, Thomas W.

2003-01-01

A process for direct integration of a thin-film silicon p-n junction diode with a magnetic tunnel junction for use in advanced magnetic random access memory (MRAM) cells for high performance, non-volatile memory arrays. The process is based on pulsed laser processing for the fabrication of vertical polycrystalline silicon electronic device structures, in particular p-n junction diodes, on films of metals deposited onto low temperature-substrates such as ceramics, dielectrics, glass, or polymers. The process preserves underlayers and structures onto which the devices are typically deposited, such as silicon integrated circuits. The process involves the low temperature deposition of at least one layer of silicon, either in an amorphous or a polycrystalline phase on a metal layer. Dopants may be introduced in the silicon film during or after deposition. The film is then irradiated with short pulse laser energy that is efficiently absorbed in the silicon, which results in the crystallization of the film and simultaneously in the activation of the dopants via ultrafast melting and solidification. The silicon film can be patterned either before or after crystallization.

Controlled laser delivery into biological tissue via thin-film optical tunneling and refraction

NASA Astrophysics Data System (ADS)

Whiteside, Paul J. D.; Goldschmidt, Benjamin S.; Curry, Randy; Viator, John A.

2015-02-01

Due to the often extreme energies employed, contemporary methods of laser delivery utilized in clinical dermatology allow for a dangerous amount of high-intensity laser light to reflect off a multitude of surfaces, including the patient's own skin. Such techniques consistently represent a clear and present threat to both patients and practitioners alike. The intention of this work was therefore to develop a technique that mitigates this problem by coupling the light directly into the tissue via physical contact with an optical waveguide. In this manner, planar waveguides cladded in silver with thin-film active areas were used to illuminate agar tissue phantoms with nanosecond-pulsed laser light at 532nm. The light then either refracted or optically tunneled through the active area, photoacoustically generating ultrasonic waves within the phantom, whose peak-to-peak intensity directly correlated to the internal reflection angle of the beam. Consequently, angular spectra for energy delivery were recorded for sub-wavelength silver and titanium films of variable thickness. Optimal energy delivery was achieved for internal reflection angles ranging from 43 to 50 degrees, depending on the active area and thin film geometries, with titanium films consistently delivering more energy across the entire angular spectrum due to their relatively high refractive index. The technique demonstrated herein therefore not only represents a viable method of energy delivery for biological tissue while minimizing the possibility for stray light, but also demonstrates the possibility for utilizing thin films of high refractive index metals to redirect light out of an optical waveguide.

False-positive cryptococcal antigen latex agglutination caused by disinfectants and soaps.

PubMed Central

Blevins, L B; Fenn, J; Segal, H; Newcomb-Gayman, P; Carroll, K C

1995-01-01

Five disinfectants or soaps were tested to determine if any could be responsible for false-positive results obtained with the Latex-Crypto Antigen Detection System kit (Immuno-Mycologics, Inc., Norman, Okla.). Three disinfectants or soaps (Derma soap, 7X, and Bacdown) produced false-positive agglutination after repeated washing of ring slides during testing of a known negative cerebrospinal fluid specimen. PMID:7650214

40 CFR 417.10 - Applicability; description of the soap manufacturing by batch kettle subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 29 2014-07-01 2012-07-01 true Applicability; description of the soap... PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SOAP AND DETERGENT MANUFACTURING POINT SOURCE CATEGORY Soap Manufacturing by Batch Kettle Subcategory § 417.10 Applicability; description of the soap...

40 CFR 417.10 - Applicability; description of the soap manufacturing by batch kettle subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 30 2012-07-01 2012-07-01 false Applicability; description of the soap... PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SOAP AND DETERGENT MANUFACTURING POINT SOURCE CATEGORY Soap Manufacturing by Batch Kettle Subcategory § 417.10 Applicability; description of the soap...

40 CFR 417.10 - Applicability; description of the soap manufacturing by batch kettle subcategory.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 30 2013-07-01 2012-07-01 true Applicability; description of the soap... PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SOAP AND DETERGENT MANUFACTURING POINT SOURCE CATEGORY Soap Manufacturing by Batch Kettle Subcategory § 417.10 Applicability; description of the soap...

Tunneling Spectroscopy of Superconducting MoN and NbTiN Grown by Atomic Layer Deposition.

DOE PAGES

Groll, Nickolas; Klug, Jeffrey A.; Cao, Chaoyue; ...

2014-03-03

A tunneling spectroscopy study is presented of superconducting MoN and Nbo.8Tio.2N thin films grown by atomic layer deposition (ALD). The films exhibited a superconducting gap of 2meV and 2.4meV, respectively, with a corresponding critical temperature of 11.5K and 13.4 K, among the highest reported Tc values achieved by the ALD technique.Tunnel junctions were obtained using a mechanical contact method with a Au tip. While the native oxides of these films provided poor tunnel barriers, high quality tunnel junctions with low zero bias conductance (below rvl0%) were obtained using an artificial tunnel barrier of Ah03 on the film's surface grown exmore » situ by ALD. We find a large critical current density on the order of 4 x 106Ncm2 at T =0.8Tc for a 60 run MoN film and demonstrate conformal coating capabilities of ALD onto high aspect ratio geometries. These results suggest that the ALD technique offers significant promise for thin film superconducting device applications.« less

Tunneling spectroscopy of superconducting MoN and NbTiN grown by atomic layer deposition

NASA Astrophysics Data System (ADS)

Groll, Nickolas R.; Klug, Jeffrey A.; Cao, Chaoyue; Altin, Serdar; Claus, Helmut; Becker, Nicholas G.; Zasadzinski, John F.; Pellin, Michael J.; Proslier, Thomas

2014-03-01

A tunneling spectroscopy study is presented of superconducting MoN and Nb0.8Ti0.2N thin films grown by atomic layer deposition (ALD). The films exhibited a superconducting gap of 2 meV and 2.4 meV, respectively, with a corresponding critical temperature of 11.5 K and 13.4 K, among the highest reported Tc values achieved by the ALD technique. Tunnel junctions were obtained using a mechanical contact method with a Au tip. While the native oxides of these films provided poor tunnel barriers, high quality tunnel junctions with low zero bias conductance (below ˜10%) were obtained using an artificial tunnel barrier of Al2O3 on the film's surface grown ex situ by ALD. We find a large critical current density on the order of 4 × 106 A/cm2 at T = 0.8Tc for a 60 nm MoN film and demonstrate conformal coating capabilities of ALD onto high aspect ratio geometries. These results suggest that the ALD technique offers significant promise for thin film superconducting device applications.

Columnar to Nematic Mesophase Transition: Binary Mixtures of Unlike Copper Soaps

NASA Astrophysics Data System (ADS)

Seghrouchni, R.; Skoulios, A.

1995-10-01

Copper (II) soaps are known to produce columnar mesophases at high temperature. The polar groups of the soap molecules are stacked over one another within columns surrounded by the alkyl chains in a disordered conformation and laterally arranged according to a two-dimensional hexagonal lattice. The present work studies the mesomorphic behaviour of binary mixtures of copper soaps using differential scanning calorimetry, polarizing microscopy, and X-ray diffraction. When the soaps are of comparable molecular sizes the mixtures are homogeneous and columnar at all compositions. The columns of the two soaps, remaining intact in the mixture, are distributed randomly on the nodes of a hexagonal Bravais lattice. Crystallographic homogeneity is obtained by transfer of methylene groups from cell to cell. When, on the other hand, the soaps are different enough in molecular sizes, the columnar structure of the mixtures is interrupted in the middle range of compositions for the benefit of a nematic one. The transfer of methylene groups gets indeed harder to achieve and the distortion of the hexagonal units cells becomes important. The columnar to nematic phase transition is discussed on a molecular and a topological level.

Foam structure :from soap froth to solid foams.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kraynik, Andrew Michael

2003-01-01

The properties of solid foams depend on their structure, which usually evolves in the fluid state as gas bubbles expand to form polyhedral cells. The characteristic feature of foam structure-randomly packed cells of different sizes and shapes-is examined in this article by considering soap froth. This material can be modeled as a network of minimal surfaces that divide space into polyhedral cells. The cell-level geometry of random soap froth is calculated with Brakke's Surface Evolver software. The distribution of cell volumes ranges from monodisperse to highly polydisperse. Topological and geometric properties, such as surface area and edge length, of themore » entire foam and individual cells, are discussed. The shape of struts in solid foams is related to Plateau borders in liquid foams and calculated for different volume fractions of material. The models of soap froth are used as templates to produce finite element models of open-cell foams. Three-dimensional images of open-cell foams obtained with x-ray microtomography allow virtual reconstruction of skeletal structures that compare well with the Surface Evolver simulations of soap-froth geometry.« less

Waterflooding employing surfactants derived from metallic soaps

DOE Office of Scientific and Technical Information (OSTI.GOV)

Williams, S.A.

1975-12-16

A waterflooding process is described in which a petroleum oil containing divalent metal soaps is contacted with an inorganic acid in order to convert the soaps to the corresponding organic acids. The organic acids thus obtained may be injected into the reservoir followed by an aqueous alkaline solution. Alternatively, the organic acids may be contacted with an aqueous solution in order to convert the acids to the corresponding surface-active monovalent salts, which may be then injected into the reservoir. (4 claims)

Antibacterial properties of soap containing some fatty acid esters.

PubMed

Pandey, N K; Natraj, C V; Kalle, G P; Nambudiry, M E

1985-02-01

Synopsis Chemical microbial inhibitors compatible with formulations of soaps and deodorant perfumes are more effective if they are substantive to the skin. However, highly effective inhibitors are toxic and their substantivity on skin may accentuate the toxicity. Natural compounds such as short to medium chain fatty acids and their derivatives, which are known to be germicidal, offer a viable alternative to chemical inhibitors. We report here the synthesis of sodium 2-lauroyloxy propionate and an in vivo method to test its substantivity on skin following its incorporation in soaps. Among several compounds tested, sodium 2-lauroyloxy propionate was found to be highly substantive in soap formulation.

Antimicrobial Activity of Medicated Soaps Commonly Used By Dar es Salaam Residents in Tanzania.

PubMed

Mwambete, K D; Lyombe, F

2011-01-01

An in vitro evaluation of the anti-microbial activity of medicated soaps was conducted using ditch-plate and hand washing techniques. Strains of reference microbes namely Candida albicans (ATCC90028), Staphylococcus aureus (ATCC25923), Pseudomonas aureginosa (ATCC27853) and Escherichia coli (ATCC25922) were tested at three different soaps' concentrations (1.0, 4.0 and 8.0 mg/ml). A total of 16 medicated soaps were assayed for their antimicrobial efficacy. Of these, 13 were medicated and 3 non-medicated soaps, which served as control. Ciprofloxacin and ketaconazole were employed as positive controls. Label disclosure for the soaps' ingredients and other relevant information were absorbed. The most common antimicrobial active ingredients were triclosan, trichloroxylenol and trichlorocarbanilide. ANOVA for means of zones of inhibition revealed variability of antimicrobial activity among the medicated soaps. Positive correlation (r=0.318; P<0.01) between zones of inhibition and soaps' concentrations was evidenced. Hand washing frequencies positively correlated with microbial counts. Roberts(®) soap exhibited the largest zone of inhibition (34 mm) on S. aureus. Candida albicans was the least susceptible microbe. Regency(®) and Dalan(®) exhibited the least zone of inhibition on the tested bacteria. Protex(®), Roberts(®), Family(®) and Protector(®) were equally effective (P<0.01) against S. aureus. In conclusion, majority of the assayed medicated soaps have satisfactory antibacterial activity; though lack antifungal effect with exception of Linda(®) liquid soap. The hand washing technique has proved to be inappropriate for evaluation of soaps' antimicrobial efficacy due to presence of the skin microflora.

The 'Dope' on Soaps.

ERIC Educational Resources Information Center

MacDonald, Patrick T.

1983-01-01

Used a sample of 165 long-time soap opera viewers to examine the context, motives, and consequences of drug use in daytime serials. Results showed alcohol was seen more frequently than any other drug. Portrayal of illegal drugs was much less common than that of legal drugs. (JAC)

Bacterial Hand Contamination and Transfer after Use of Contaminated Bulk-Soap-Refillable Dispensers▿†

PubMed Central

Zapka, Carrie A.; Campbell, Esther J.; Maxwell, Sheri L.; Gerba, Charles P.; Dolan, Michael J.; Arbogast, James W.; Macinga, David R.

2011-01-01

Bulk-soap-refillable dispensers are prone to extrinsic bacterial contamination, and recent studies demonstrated that approximately one in four dispensers in public restrooms are contaminated. The purpose of this study was to quantify bacterial hand contamination and transfer after use of contaminated soap under controlled laboratory and in-use conditions in a community setting. Under laboratory conditions using liquid soap experimentally contaminated with 7.51 log10 CFU/ml of Serratia marcescens, an average of 5.28 log10 CFU remained on each hand after washing, and 2.23 log10 CFU was transferred to an agar surface. In an elementary-school-based field study, Gram-negative bacteria on the hands of students and staff increased by 1.42 log10 CFU per hand (26-fold) after washing with soap from contaminated bulk-soap-refillable dispensers. In contrast, washing with soap from dispensers with sealed refills significantly reduced bacteria on hands by 0.30 log10 CFU per hand (2-fold). Additionally, the mean number of Gram-negative bacteria transferred to surfaces after washing with soap from dispensers with sealed-soap refills (0.06 log10 CFU) was significantly lower than the mean number after washing with contaminated bulk-soap-refillable dispensers (0.74 log10 CFU; P < 0.01). Finally, significantly higher levels of Gram-negative bacteria were recovered from students (2.82 log10 CFU per hand) than were recovered from staff (2.22 log10 CFU per hand) after washing with contaminated bulk soap (P < 0.01). These results demonstrate that washing with contaminated soap from bulk-soap-refillable dispensers can increase the number of opportunistic pathogens on the hands and may play a role in the transmission of bacteria in public settings. PMID:21421792

Evaluation of various agro-wastes for traditional black soap production.

PubMed

Taiwo, O E; Osinowo, F A

2001-08-01

The agricultural wastes, cocoa-pod husks, palm-bunch waste, sorghum chaff and groundnut shells, which are normally thrown away have been used in the production of black soap. Unlike other soaps which are made from oils and chemicals, black soap is made from oils and agro-wastes ashes. Chemical analysis indicated that the liquid extract from the ashes of the different agro-wastes used contained various amounts of potassium and sodium compounds. The most common ingredient in the agro-wastes was potassium carbonate. The amount of potassium carbonate was 56.73 +/- 0.16% in cocoa-pod ash, 43.15 +/- 0.13% in palm-bunch ash, 16.65 +/- 0.05% in groundnut shell ash and 12.40 +/- 0.08% in sorghum chaff ash. Soaps made from the agro-wastes ashes had excellent solubility, consistency, cleansing and lathering abilities.

Exploring Determinants of Handwashing with Soap in Indonesia: A Quantitative Analysis

PubMed Central

Hirai, Mitsuaki; Graham, Jay P.; Mattson, Kay D.; Kelsey, Andrea; Mukherji, Supriya; Cronin, Aidan A.

2016-01-01

Handwashing with soap is recognized as a cost-effective intervention to reduce morbidity and mortality associated with enteric and respiratory infections. This study analyzes rural Indonesian households’ hygiene behaviors and attitudes to examine how motivations for handwashing, locations of handwashing space in the household, and handwashing moments are associated with handwashing with soap as potential determinants of the behavior. The analysis was conducted using results from a UNICEF cross-sectional study of 1700 households in six districts across three provinces of Indonesia. A composite measure of handwashing with soap was developed that included self-reported handwashing, a handwashing demonstration, and observed handwashing materials and location of facilities in the home. Prevalence ratios were calculated to analyze associations between handwashing with soap and hypothesized determinants of the behavior. Our results showed that determinants that had a significant association with handwashing with soap included: (1) a desire to smell nice; (2) interpersonal influences; (3) the presence of handwashing places within 10 paces of the kitchen and the toilet; and (4) key handwashing moments when hands felt dirty, including after eating and after cleaning child stools. This study concludes that handwashing with soap may be more effectively promoted through the use of non-health messages. PMID:27598178

Exploring Determinants of Handwashing with Soap in Indonesia: A Quantitative Analysis.

PubMed

Hirai, Mitsuaki; Graham, Jay P; Mattson, Kay D; Kelsey, Andrea; Mukherji, Supriya; Cronin, Aidan A

2016-09-01

Handwashing with soap is recognized as a cost-effective intervention to reduce morbidity and mortality associated with enteric and respiratory infections. This study analyzes rural Indonesian households' hygiene behaviors and attitudes to examine how motivations for handwashing, locations of handwashing space in the household, and handwashing moments are associated with handwashing with soap as potential determinants of the behavior. The analysis was conducted using results from a UNICEF cross-sectional study of 1700 households in six districts across three provinces of Indonesia. A composite measure of handwashing with soap was developed that included self-reported handwashing, a handwashing demonstration, and observed handwashing materials and location of facilities in the home. Prevalence ratios were calculated to analyze associations between handwashing with soap and hypothesized determinants of the behavior. Our results showed that determinants that had a significant association with handwashing with soap included: (1) a desire to smell nice; (2) interpersonal influences; (3) the presence of handwashing places within 10 paces of the kitchen and the toilet; and (4) key handwashing moments when hands felt dirty, including after eating and after cleaning child stools. This study concludes that handwashing with soap may be more effectively promoted through the use of non-health messages.

A High Performance SOAP Engine for Grid Computing

NASA Astrophysics Data System (ADS)

Wang, Ning; Welzl, Michael; Zhang, Liang

Web Service technology still has many defects that make its usage for Grid computing problematic, most notably the low performance of the SOAP engine. In this paper, we develop a novel SOAP engine called SOAPExpress, which adopts two key techniques for improving processing performance: SCTP data transport and dynamic early binding based data mapping. Experimental results show a significant and consistent performance improvement of SOAPExpress over Apache Axis.

Alternative Hand Contamination Technique To Compare the Activities of Antimicrobial and Nonantimicrobial Soaps under Different Test Conditions▿

PubMed Central

Fuls, Janice L.; Rodgers, Nancy D.; Fischler, George E.; Howard, Jeanne M.; Patel, Monica; Weidner, Patrick L.; Duran, Melani H.

2008-01-01

Antimicrobial hand soaps provide a greater bacterial reduction than nonantimicrobial soaps. However, the link between greater bacterial reduction and a reduction of disease has not been definitively demonstrated. Confounding factors, such as compliance, soap volume, and wash time, may all influence the outcomes of studies. The aim of this work was to examine the effects of wash time and soap volume on the relative activities and the subsequent transfer of bacteria to inanimate objects for antimicrobial and nonantimicrobial soaps. Increasing the wash time from 15 to 30 seconds increased reduction of Shigella flexneri from 2.90 to 3.33 log10 counts (P = 0.086) for the antimicrobial soap, while nonantimicrobial soap achieved reductions of 1.72 and 1.67 log10 counts (P > 0.6). Increasing soap volume increased bacterial reductions for both the antimicrobial and the nonantimicrobial soaps. When the soap volume was normalized based on weight (∼3 g), nonantimicrobial soap reduced Serratia marcescens by 1.08 log10 counts, compared to the 3.83-log10 reduction caused by the antimicrobial soap (P < 0.001). The transfer of Escherichia coli to plastic balls following a 15-second hand wash with antimicrobial soap resulted in a bacterial recovery of 2.49 log10 counts, compared to the 4.22-log10 (P < 0.001) bacterial recovery on balls handled by hands washed with nonantimicrobial soap. This indicates that nonantimicrobial soap was less active and that the effectiveness of antimicrobial soaps can be improved with longer wash time and greater soap volume. The transfer of bacteria to objects was significantly reduced due to greater reduction in bacteria following the use of antimicrobial soap. PMID:18441107

Alternative hand contamination technique to compare the activities of antimicrobial and nonantimicrobial soaps under different test conditions.

PubMed

Fuls, Janice L; Rodgers, Nancy D; Fischler, George E; Howard, Jeanne M; Patel, Monica; Weidner, Patrick L; Duran, Melani H

2008-06-01

Antimicrobial hand soaps provide a greater bacterial reduction than nonantimicrobial soaps. However, the link between greater bacterial reduction and a reduction of disease has not been definitively demonstrated. Confounding factors, such as compliance, soap volume, and wash time, may all influence the outcomes of studies. The aim of this work was to examine the effects of wash time and soap volume on the relative activities and the subsequent transfer of bacteria to inanimate objects for antimicrobial and nonantimicrobial soaps. Increasing the wash time from 15 to 30 seconds increased reduction of Shigella flexneri from 2.90 to 3.33 log(10) counts (P = 0.086) for the antimicrobial soap, while nonantimicrobial soap achieved reductions of 1.72 and 1.67 log(10) counts (P > 0.6). Increasing soap volume increased bacterial reductions for both the antimicrobial and the nonantimicrobial soaps. When the soap volume was normalized based on weight (approximately 3 g), nonantimicrobial soap reduced Serratia marcescens by 1.08 log(10) counts, compared to the 3.83-log(10) reduction caused by the antimicrobial soap (P < 0.001). The transfer of Escherichia coli to plastic balls following a 15-second hand wash with antimicrobial soap resulted in a bacterial recovery of 2.49 log(10) counts, compared to the 4.22-log(10) (P < 0.001) bacterial recovery on balls handled by hands washed with nonantimicrobial soap. This indicates that nonantimicrobial soap was less active and that the effectiveness of antimicrobial soaps can be improved with longer wash time and greater soap volume. The transfer of bacteria to objects was significantly reduced due to greater reduction in bacteria following the use of antimicrobial soap.

SPICE Module for the Satellite Orbit Analysis Program (SOAP)

NASA Technical Reports Server (NTRS)

Coggi, John; Carnright, Robert; Hildebrand, Claude

2008-01-01

A SPICE module for the Satellite Orbit Analysis Program (SOAP) precisely represents complex motion and maneuvers in an interactive, 3D animated environment with support for user-defined quantitative outputs. (SPICE stands for Spacecraft, Planet, Instrument, Camera-matrix, and Events). This module enables the SOAP software to exploit NASA mission ephemeris represented in the JPL Ancillary Information Facility (NAIF) SPICE formats. Ephemeris types supported include position, velocity, and orientation for spacecraft and planetary bodies including the Sun, planets, natural satellites, comets, and asteroids. Entire missions can now be imported into SOAP for 3D visualization, playback, and analysis. The SOAP analysis and display features can now leverage detailed mission files to offer the analyst both a numerically correct and aesthetically pleasing combination of results that can be varied to study many hypothetical scenarios. The software provides a modeling and simulation environment that can encompass a broad variety of problems using orbital prediction. For example, ground coverage analysis, communications analysis, power and thermal analysis, and 3D visualization that provide the user with insight into complex geometric relations are included. The SOAP SPICE module allows distributed science and engineering teams to share common mission models of known pedigree, which greatly reduces duplication of effort and the potential for error. The use of the software spans all phases of the space system lifecycle, from the study of future concepts to operations and anomaly analysis. It allows SOAP software to correctly position and orient all of the principal bodies of the Solar System within a single simulation session along with multiple spacecraft trajectories and the orientation of mission payloads. In addition to the 3D visualization, the user can define numeric variables and x-y plots to quantitatively assess metrics of interest.

40 CFR 417.80 - Applicability; description of the manufacture of liquid soaps subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

... manufacture of liquid soaps subcategory. 417.80 Section 417.80 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SOAP AND DETERGENT MANUFACTURING POINT SOURCE CATEGORY Manufacture of Liquid Soaps Subcategory § 417.80 Applicability; description of the manufacture of...

40 CFR 417.80 - Applicability; description of the manufacture of liquid soaps subcategory.

Code of Federal Regulations, 2013 CFR

2013-07-01

... manufacture of liquid soaps subcategory. 417.80 Section 417.80 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SOAP AND DETERGENT MANUFACTURING POINT SOURCE CATEGORY Manufacture of Liquid Soaps Subcategory § 417.80 Applicability; description of the manufacture of...

40 CFR 417.70 - Applicability; description of the manufacture of bar soaps subcategory.

Code of Federal Regulations, 2013 CFR

2013-07-01

... manufacture of bar soaps subcategory. 417.70 Section 417.70 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SOAP AND DETERGENT MANUFACTURING POINT SOURCE CATEGORY Manufacture of Bar Soaps Subcategory § 417.70 Applicability; description of the manufacture of bar...

40 CFR 417.80 - Applicability; description of the manufacture of liquid soaps subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

... manufacture of liquid soaps subcategory. 417.80 Section 417.80 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SOAP AND DETERGENT MANUFACTURING POINT SOURCE CATEGORY Manufacture of Liquid Soaps Subcategory § 417.80 Applicability; description of the manufacture of...

40 CFR 417.70 - Applicability; description of the manufacture of bar soaps subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

... manufacture of bar soaps subcategory. 417.70 Section 417.70 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SOAP AND DETERGENT MANUFACTURING POINT SOURCE CATEGORY Manufacture of Bar Soaps Subcategory § 417.70 Applicability; description of the manufacture of bar...

40 CFR 417.70 - Applicability; description of the manufacture of bar soaps subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

... manufacture of bar soaps subcategory. 417.70 Section 417.70 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SOAP AND DETERGENT MANUFACTURING POINT SOURCE CATEGORY Manufacture of Bar Soaps Subcategory § 417.70 Applicability; description of the manufacture of bar...

Green Soap: An Extraction and Saponification of Avocado Oil

ERIC Educational Resources Information Center

Sutheimer, Susan; Caster, Jacqueline M.; Smith, Simone H.

2015-01-01

An introductory level green chemistry experiment is described that places a new twist on soap-making in lab. In this experiment, oil is extracted from an avocado, after which the oil is saponified to produce bars of green craft soap. Commonly used extraction solvents, such as petroleum ether, methylene chloride, and hexane, are replaced with safer…

Ferroelectricity and tunneling electroresistance effect in asymmetric ferroelectric tunnel junctions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tao, L. L.; Wang, J., E-mail: jianwang@hku.hk

2016-06-14

We report the investigation on the ferroelectricity and tunneling electroresistance (TER) effect in PbTiO{sub 3} (PTO)-based ferroelectric tunnel junctions (FTJs) using first-principles calculations. For symmetric FTJs, we have calculated the average polarizations of PTO film and effective screening lengths of different metal electrodes for a number of FTJs, which is useful for experimental research. For asymmetric FTJs, significant asymmetric ferroelectric displacements in PTO film are observed, which is attributed to the intrinsic field generated by the two dissimilar electrodes. Moreover, by performing quantum transport calculations on those asymmetric FTJs, a sizable TER effect is observed. It is found that themore » asymmetry of ferroelectric displacements in PTO barrier, which is determined by the difference of work functions of the electrodes, controls the observed TER effect. Our results will help unravel the TER mechanism of asymmetric FTJs in most experiments and will be useful for the designing of FTJ-based devices.« less

A community-randomised controlled trial promoting waterless hand sanitizer and handwashing with soap, Dhaka, Bangladesh.

PubMed

Luby, Stephen P; Kadir, Mohammad Abdul; Yushuf Sharker, M A; Yeasmin, Farzana; Unicomb, Leanne; Sirajul Islam, M

2010-12-01

To pilot two intensive hand hygiene promotion interventions, one using soap and one using a waterless hand sanitizer, in low-income housing compounds in Dhaka, Bangladesh and assess subsequent changes in handwashing behaviour and hand microbiology. Fieldworkers randomized 30 housing compounds: 10 received handwashing promotion with free soap, 10 received handwashing promotion with free waterless hand sanitizer and 10 were non-intervention controls. Fieldworkers assessed handwashing behaviour by structured observation and collected hand rinse specimens. At baseline, compound residents washed their hands with soap 26% of the time after defecation and 30% after cleaning a child's anus but <1% at other times. Compared with baseline, residents of soap intervention compounds were much more likely to wash their hands with soap after faecal contact (85-91%), before preparing food (26%) and before eating (26%). Compounds that received waterless hand sanitizer cleansed their hands more commonly than control compounds that used soap (10.4%vs. 2.3%), but less commonly than soap intervention compounds used soap (25%). Post-intervention hand rinse samples from soap and sanitizer compounds had lower concentrations of faecal indicator bacteria compared with baseline and control compounds. Waterless hand sanitizer was readily adopted by this low-income community and reduced hand contamination but did not improve the frequency of handwashing compared with soap. Future deployments of waterless hand sanitizers may improve hand hygiene more effectively by targeting settings where soap and water is unavailable. © 2010 Blackwell Publishing Ltd.

NPDES Permit for Soap Creek Associates Wastewater Treatment Facility in Montana

EPA Pesticide Factsheets

Under National Pollutant Discharge Elimination System permit number MT-0023183, Soap Creek Associates, Inc. is authorized to discharge from its wastewater treatment facility located in West, Bighorn County, Montana, to Soap Creek.

Spin-polarized scanning tunneling microscopy experiments on the rough surface of a polycrystalline NiFe film with a fine magnetic tip sensitive to a well-defined magnetization component

DOE Office of Scientific and Technical Information (OSTI.GOV)

Matsuyama, H., E-mail: matsu@phys.sci.hokudai.ac.jp; Nara, D.; Kageyama, R.

We developed a micrometer-sized magnetic tip integrated onto the write head of a hard disk drive for spin-polarized scanning tunneling microscopy (SP-STM) in the modulated tip magnetization mode. Using SP-STM, we measured a well-defined in-plane spin-component of the tunneling current of the rough surface of a polycrystalline NiFe film. The spin asymmetry of the NiFe film was about 1.3% within the bias voltage range of -3 to 1 V. We obtained the local spin component image of the sample surface, switching the magnetic field of the sample to reverse the sample magnetization during scanning. We also obtained a spin imagemore » of the rough surface of a polycrystalline NiFe film evaporated on the recording medium of a hard disk drive.« less

Atomically Thin Al2O3 Films for Tunnel Junctions

NASA Astrophysics Data System (ADS)

Wilt, Jamie; Gong, Youpin; Gong, Ming; Su, Feifan; Xu, Huikai; Sakidja, Ridwan; Elliot, Alan; Lu, Rongtao; Zhao, Shiping; Han, Siyuan; Wu, Judy Z.

2017-06-01

Metal-insulator-metal tunnel junctions are common throughout the microelectronics industry. The industry standard AlOx tunnel barrier, formed through oxygen diffusion into an Al wetting layer, is plagued by internal defects and pinholes which prevent the realization of atomically thin barriers demanded for enhanced quantum coherence. In this work, we employ in situ scanning tunneling spectroscopy along with molecular-dynamics simulations to understand and control the growth of atomically thin Al2O3 tunnel barriers using atomic-layer deposition. We find that a carefully tuned initial H2O pulse hydroxylated the Al surface and enabled the creation of an atomically thin Al2O3 tunnel barrier with a high-quality M -I interface and a significantly enhanced barrier height compared to thermal AlOx . These properties, corroborated by fabricated Josephson junctions, show that atomic-layer deposition Al2O3 is a dense, leak-free tunnel barrier with a low defect density which can be a key component for the next generation of metal-insulator-metal tunnel junctions.

40 CFR 417.70 - Applicability; description of the manufacture of bar soaps subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 29 2011-07-01 2009-07-01 true Applicability; description of the manufacture of bar soaps subcategory. 417.70 Section 417.70 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SOAP AND DETERGENT MANUFACTURING POINT SOURCE CATEGORY Manufacture of Bar Soaps Subcategor...

40 CFR 417.70 - Applicability; description of the manufacture of bar soaps subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 28 2010-07-01 2010-07-01 true Applicability; description of the manufacture of bar soaps subcategory. 417.70 Section 417.70 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SOAP AND DETERGENT MANUFACTURING POINT SOURCE CATEGORY Manufacture of Bar Soaps Subcategor...

40 CFR 417.80 - Applicability; description of the manufacture of liquid soaps subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 29 2011-07-01 2009-07-01 true Applicability; description of the manufacture of liquid soaps subcategory. 417.80 Section 417.80 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SOAP AND DETERGENT MANUFACTURING POINT SOURCE CATEGORY Manufacture of Liquid Soaps...

40 CFR 417.80 - Applicability; description of the manufacture of liquid soaps subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 28 2010-07-01 2010-07-01 true Applicability; description of the manufacture of liquid soaps subcategory. 417.80 Section 417.80 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SOAP AND DETERGENT MANUFACTURING POINT SOURCE CATEGORY Manufacture of Liquid Soaps...

The crystallization of metal soaps and fatty acids in oil paint model systems.

PubMed

Hermans, Joen J; Keune, Katrien; van Loon, Annelies; Iedema, Piet D

2016-04-28

The formation and crystallization of metal soaps in oil paint layers is an important issue in the conservation of oil paintings. The chemical reactions and physical processes that are involved in releasing metal ions from pigments and fatty acids from the oil binder to form crystalline metal soap deposits have so far remained poorly understood. We have used a combination of differential scanning calorimetry (DSC) and attenuated total reflection Fourier transform infrared spectroscopy (ATR-FTIR) on model mixtures of palmitic acid, lead palmitate or zinc palmitate and linseed oil to study the transition from amorphous material to crystalline fatty acid or metal soap. This transition forms the final stage in the cascade of processes leading to metal soap-related oil paint degradation. Palmitic acid as well as the metal soaps showed nearly ideal solubility behavior. However, it was found that, near room temperature, both lead and zinc palmitate are practically insoluble in both liquid and partially polymerized linseed oil. Interestingly, the rate of metal soap and fatty acid crystallization decreased rapidly with the degree of linseed oil polymerization, possibly leading to systems where metal soaps are kinetically trapped in a semi-crystalline state. To explain the various morphologies of metal soap aggregates observed in oil paint layers, it is proposed that factors affecting the probability of crystal nucleation and the rate of crystal growth play a crucial role, like exposure to heat or cleaning solvents and the presence of microcracks.

6. FOURTH FLOOR, DETAIL OF HOTEL SOAP LINE TO NORTH: ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

6. FOURTH FLOOR, DETAIL OF HOTEL SOAP LINE TO NORTH: AMERICAN CAR & FOUNDRY COMPANY MANUAL SOAP CUTTER INSTALLED 1932 (FOREGROUND); CONVEYORS; AND R.A. JONES & COMPANY HORIZONTAL PRESS INSTALLED 1931 (BACKGROUND) - Colgate & Company Jersey City Plant, Building No. B-15, 90-96 Greene Street, Jersey City, Hudson County, NJ

Larvicidal activity of synthetic disinfectants and antibacterial soaps against mosquito, Culex quinquefasciatus (Diptera: Culicidae).

PubMed

Xue, Rui-De; Qualls, Whitney A

2013-01-01

Seven commercial synthetic disinfectant and antibacterial soap products were evaluated as mosquito larvicides against Culex quinquefasciatus Say in the laboratory. Three aerosol disinfectant products, at 0.01% concentration resulted in 58-76% mortality of laboratory-reared fourth instar mosquito larvae at 24 h posttreatment. Four antibacterial soap products at 0.0001% concentration resulted in 88-100% larval mortality at 24 h posttreatment. The active ingredient of the antibacterial soap products, triclosan (0.1%) resulted in 74% larval mortality. One of the antibacterial soap products, Equate caused the highest mosquito larval mortality in the laboratory. Equate antibacterial soap at the application rate of 0.000053 ppm resulted in 90% mortality of the introduced fourth instar larvae of Cx. quinquesfasicatus in the outdoor pools. In laboratory and field bioassays, the antibacterial soap resulted in significant larval mosquito mortality.

Quantifying the Effects of Water Temperature, Soap Volume, Lather Time, and Antimicrobial Soap as Variables in the Removal of Escherichia coli ATCC 11229 from Hands.

PubMed

Jensen, Dane A; Macinga, David R; Shumaker, David J; Bellino, Roberto; Arbogast, James W; Schaffner, Donald W

2017-06-01

The literature on hand washing, while extensive, often contains conflicting data, and key variables are only superficially studied or not studied at all. Some hand washing recommendations are made without scientific support, and agreement between recommendations is limited. The influence of key variables such as soap volume, lather time, water temperature, and product formulation on hand washing efficacy was investigated in the present study. Baseline conditions were 1 mL of a bland (nonantimicrobial) soap, a 5-s lather time, and 38°C (100°F) water temperature. A nonpathogenic strain of Escherichia coli (ATCC 11229) was the challenge microorganism. Twenty volunteers (10 men and 10 women) participated in the study, and each test condition had 20 replicates. An antimicrobial soap formulation (1% chloroxylenol) was not significantly more effective than the bland soap for removing E. coli under a variety of test conditions. Overall, the mean reduction was 1.94 log CFU (range, 1.83 to 2.10 log CFU) with the antimicrobial soap and 2.22 log CFU (range, 1.91 to 2.54 log CFU) with the bland soap. Overall, lather time significantly influenced efficacy in one scenario, in which a 0.5-log greater reduction was observed after 20 s with bland soap compared with the baseline wash (P = 0.020). Water temperature as high as 38°C (100°F) and as low as 15°C (60°F) did not have a significant effect on the reduction of bacteria during hand washing; however, the energy usage differed between these temperatures. No significant differences were observed in mean log reductions experienced by men and women (both 2.08 log CFU; P = 0.988). A large part of the variability in the data was associated with the behaviors of the volunteers. Understanding what behaviors and human factors most influence hand washing may help researchers find techniques to optimize the effectiveness of hand washing.

Magnetization reversal mechanism of magnetic tunnel junctions

NASA Astrophysics Data System (ADS)

Liu, Cun-Ye; Li, Jian; Wang, Yue; Chen, Jian-Yong; Xu, Qing-Yu; Ni, Gang; Sang, Hai; Du, You-Wei

2002-01-01

Using the ion-beam-sputtering technique, we have fabricated Fe/Al2O3/Fe magnetic tunnelling junctions (MTJs). We have observed double-peaked shapes of curves, which have a level summit and a symmetrical feature, showing the magnetoresistance of the junction as a function of applied field. We have measured the tunnel conductance of MTJs which have insulating layers of different thicknesses. We have studied the dependence of the magnetoresistance of MTJs on tunnel conductance. The microstructures of hard- and soft-magnetic layers and interfaces of ferromagnets and insulators were probed. Analysing the influence of MJT microstructures, including those having clusters or/and granules in magnetic and non-magnetic films, a magnetization reversal mechanism (MRM) is proposed, which suggests that the MRM of tunnelling junctions may be explained by using a group-by-group reversal model of magnetic moments of the mesoscopical particles. We discuss the influence of MTJ microstructures, including those with clusters or/and granules in the ferromagnetic and non-magnetic films, on the MRM.

Use Primary Sources to Develop a Soap Opera: As the Civil War Turns

ERIC Educational Resources Information Center

Morris, Ronald V.

2002-01-01

In this article, the author describes a social studies class activity that uses primary sources to develop a soap opera based on the American Civil War. In the soap opera activity, students can watch historical characters as they grow, develop, and change. Not only do people in the soap opera develop over a long period, but their accumulated…

Ferroelectric tunneling element and memory applications which utilize the tunneling element

DOEpatents

Kalinin, Sergei V [Knoxville, TN; Christen, Hans M [Knoxville, TN; Baddorf, Arthur P [Knoxville, TN; Meunier, Vincent [Knoxville, TN; Lee, Ho Nyung [Oak Ridge, TN

2010-07-20

A tunneling element includes a thin film layer of ferroelectric material and a pair of dissimilar electrically-conductive layers disposed on opposite sides of the ferroelectric layer. Because of the dissimilarity in composition or construction between the electrically-conductive layers, the electron transport behavior of the electrically-conductive layers is polarization dependent when the tunneling element is below the Curie temperature of the layer of ferroelectric material. The element can be used as a basis of compact 1R type non-volatile random access memory (RAM). The advantages include extremely simple architecture, ultimate scalability and fast access times generic for all ferroelectric memories.

40 CFR 467.60 - Applicability; description of the drawing with emulsions or soaps subcategory.

Code of Federal Regulations, 2013 CFR

2013-07-01

... drawing with emulsions or soaps subcategory. 467.60 Section 467.60 Protection of Environment ENVIRONMENTAL... CATEGORY Drawing With Emulsions or Soaps Subcategory § 467.60 Applicability; description of the drawing with emulsions or soaps subcategory. This subpart applies to discharges of pollutants to waters of the...

40 CFR 467.60 - Applicability; description of the drawing with emulsions or soaps subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

... drawing with emulsions or soaps subcategory. 467.60 Section 467.60 Protection of Environment ENVIRONMENTAL... CATEGORY Drawing With Emulsions or Soaps Subcategory § 467.60 Applicability; description of the drawing with emulsions or soaps subcategory. This subpart applies to discharges of pollutants to waters of the...

40 CFR 467.60 - Applicability; description of the drawing with emulsions or soaps subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

... drawing with emulsions or soaps subcategory. 467.60 Section 467.60 Protection of Environment ENVIRONMENTAL... CATEGORY Drawing With Emulsions or Soaps Subcategory § 467.60 Applicability; description of the drawing with emulsions or soaps subcategory. This subpart applies to discharges of pollutants to waters of the...

Stable Ordering in Langmuir-Blodgett Films

NASA Astrophysics Data System (ADS)

Takamoto, Dawn Y.; Aydil, Eray; Zasadzinski, Joseph A.; Ivanova, Ani T.; Schwartz, Daniel K.; Yang, Tinglu; Cremer, Paul S.

2001-08-01

Defects in the layering of Langmuir-Blodgett (LB) films can be eliminated by depositing from the appropriate monolayer phase at the air-water interface. LB films deposited from the hexagonal phase of cadmium arachidate (CdA2) at pH 7 spontaneously transform into the bulk soap structure, a centrosymmetric bilayer with an orthorhombic herringbone packing. A large wavelength folding mechanism accelerates the conversion between the two structures, leading to a disruption of the desired layering. At pH > 8.5, though it is more difficult to draw LB films, almost perfect layering is obtained due to the inability to convert from the as-deposited structure to the equilibrium one.

HFSB-seeding for large-scale tomographic PIV in wind tunnels

NASA Astrophysics Data System (ADS)

Caridi, Giuseppe Carlo Alp; Ragni, Daniele; Sciacchitano, Andrea; Scarano, Fulvio

2016-12-01

A new system for large-scale tomographic particle image velocimetry in low-speed wind tunnels is presented. The system relies upon the use of sub-millimetre helium-filled soap bubbles as flow tracers, which scatter light with intensity several orders of magnitude higher than micron-sized droplets. With respect to a single bubble generator, the system increases the rate of bubbles emission by means of transient accumulation and rapid release. The governing parameters of the system are identified and discussed, namely the bubbles production rate, the accumulation and release times, the size of the bubble injector and its location with respect to the wind tunnel contraction. The relations between the above parameters, the resulting spatial concentration of tracers and measurement of dynamic spatial range are obtained and discussed. Large-scale experiments are carried out in a large low-speed wind tunnel with 2.85 × 2.85 m2 test section, where a vertical axis wind turbine of 1 m diameter is operated. Time-resolved tomographic PIV measurements are taken over a measurement volume of 40 × 20 × 15 cm3, allowing the quantitative analysis of the tip-vortex structure and dynamical evolution.

Is cutaneous malignant melanoma associated with the use of antibacterial soaps?

PubMed

Arbesman, H

1999-07-01

Since 1960, the incidence of melanoma has increased dramatically in Caucasians worldwide, and during the past decade has risen at a rate of 6% a year in the USA. A hypothesis regarding this increased incidence suggests that the prevalent use of antibacterial soaps that contain photosensitizing compounds may be a risk factor for the development of cutaneous malignant melanoma. These antibacterial soaps were introduced in the 1960s and compounds with photosensitizing properties are still present in various soaps throughout the industrialized world. The use of these antibacterial soaps, in combination with sun exposure, leads to free radical production in the skin. These free radicals are hypothesized to cause damage to melanocytes, leading to the development of melanoma. Various epidemiological findings regarding melanoma are consistent with this hypothesis. A significant reduction in the number of new cases of melanoma could be achieved if this hypothesis is correct.

Mobile Cloud Computing with SOAP and REST Web Services

NASA Astrophysics Data System (ADS)

Ali, Mushtaq; Fadli Zolkipli, Mohamad; Mohamad Zain, Jasni; Anwar, Shahid

2018-05-01

Mobile computing in conjunction with Mobile web services drives a strong approach where the limitations of mobile devices may possibly be tackled. Mobile Web Services are based on two types of technologies; SOAP and REST, which works with the existing protocols to develop Web services. Both the approaches carry their own distinct features, yet to keep the constraint features of mobile devices in mind, the better in two is considered to be the one which minimize the computation and transmission overhead while offloading. The load transferring of mobile device to remote servers for execution called computational offloading. There are numerous approaches to implement computational offloading a viable solution for eradicating the resources constraints of mobile device, yet a dynamic method of computational offloading is always required for a smooth and simple migration of complex tasks. The intention of this work is to present a distinctive approach which may not engage the mobile resources for longer time. The concept of web services utilized in our work to delegate the computational intensive tasks for remote execution. We tested both SOAP Web services approach and REST Web Services for mobile computing. Two parameters considered in our lab experiments to test; Execution Time and Energy Consumption. The results show that RESTful Web services execution is far better than executing the same application by SOAP Web services approach, in terms of execution time and energy consumption. Conducting experiments with the developed prototype matrix multiplication app, REST execution time is about 200% better than SOAP execution approach. In case of energy consumption REST execution is about 250% better than SOAP execution approach.

40 CFR 417.10 - Applicability; description of the soap manufacturing by batch kettle subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 28 2010-07-01 2010-07-01 true Applicability; description of the soap manufacturing by batch kettle subcategory. 417.10 Section 417.10 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SOAP AND DETERGENT MANUFACTURING POINT SOURCE CATEGORY Soap Manufacturing by...

40 CFR 417.10 - Applicability; description of the soap manufacturing by batch kettle subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 29 2011-07-01 2009-07-01 true Applicability; description of the soap manufacturing by batch kettle subcategory. 417.10 Section 417.10 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SOAP AND DETERGENT MANUFACTURING POINT SOURCE CATEGORY Soap Manufacturing by...

Strain-enhanced tunneling magnetoresistance in MgO magnetic tunnel junctions

PubMed Central

Loong, Li Ming; Qiu, Xuepeng; Neo, Zhi Peng; Deorani, Praveen; Wu, Yang; Bhatia, Charanjit S.; Saeys, Mark; Yang, Hyunsoo

2014-01-01

While the effects of lattice mismatch-induced strain, mechanical strain, as well as the intrinsic strain of thin films are sometimes detrimental, resulting in mechanical deformation and failure, strain can also be usefully harnessed for applications such as data storage, transistors, solar cells, and strain gauges, among other things. Here, we demonstrate that quantum transport across magnetic tunnel junctions (MTJs) can be significantly affected by the introduction of controllable mechanical strain, achieving an enhancement factor of ~2 in the experimental tunneling magnetoresistance (TMR) ratio. We further correlate this strain-enhanced TMR with coherent spin tunneling through the MgO barrier. Moreover, the strain-enhanced TMR is analyzed using non-equilibrium Green's function (NEGF) quantum transport calculations. Our results help elucidate the TMR mechanism at the atomic level and can provide a new way to enhance, as well as tune, the quantum properties in nanoscale materials and devices. PMID:25266219

Electron Microscopy Imaging of Zinc Soaps Nucleation in Oil Paint.

PubMed

Hermans, Joen; Osmond, Gillian; van Loon, Annelies; Iedema, Piet; Chapman, Robyn; Drennan, John; Jack, Kevin; Rasch, Ronald; Morgan, Garry; Zhang, Zhi; Monteiro, Michael; Keune, Katrien

2018-06-04

Using the recently developed techniques of electron tomography, we have explored the first stages of disfiguring formation of zinc soaps in modern oil paintings. The formation of complexes of zinc ions with fatty acids in paint layers is a major threat to the stability and appearance of many late 19th and early 20th century oil paintings. Moreover, the occurrence of zinc soaps in oil paintings leading to defects is disturbingly common, but the chemical reactions and migration mechanisms leading to large zinc soap aggregates or zones remain poorly understood. State-of-the-art scanning (SEM) and transmission (TEM) electron microscopy techniques, primarily developed for biological specimens, have enabled us to visualize the earliest stages of crystalline zinc soap growth in a reconstructed zinc white (ZnO) oil paint sample. In situ sectioning techniques and sequential imaging within the SEM allowed three-dimensional tomographic reconstruction of sample morphology. Improvements in the detection and discrimination of backscattered electrons enabled us to identify local precipitation processes with small atomic number contrast. The SEM images were correlated to low-dose and high-sensitivity TEM images, with high-resolution tomography providing unprecedented insight into the structure of nucleating zinc soaps at the molecular level. The correlative approach applied here to study phase separation, and crystallization processes specific to a problem in art conservation creates possibilities for visualization of phase formation in a wide range of soft materials.

Evaluation of pH of Bathing Soaps and Shampoos for Skin and Hair Care.

PubMed

Tarun, Jose; Susan, Jose; Suria, Jacob; Susan, Veronica John; Criton, Sebastian

2014-09-01

Normal healthy skin has potential of hydrogen (pH) range of 5.4-5.9 and a normal bacterial flora. Use of soap with high pH causes an increase in skin pH, which in turn causes an increase in dehydrative effect, irritability and alteration in bacterial flora. The majority of soaps and shampoos available in the market do not disclose their pH. The aim of this study was to assess the pH of different brands of bathing soaps and shampoos available in the market. The samples of soaps and shampoos were collected from shops in the locality. The samples of different brands are coded before the analysis of the pH. Solution of each sample was made and pH was measured using pH meter. Majority of the soaps have a pH within the range of 9-10. Majority of the shampoos have a pH within the range of 6-7. The soaps and shampoos commonly used by the population at large have a pH outside the range of normal skin and hair pH values. Therefore, it is hoped that before recommending soap to patient especially those who have sensitive and acne prone skin, due consideration is given to the pH factor and also that manufacturers will give a thought to pH of soaps and shampoos manufactured by them, so that their products will be more skin and hair friendly.

Laundry Soap from Waste Cooking Oil. What We Make. Science and Technology Education in Philippine Society.

ERIC Educational Resources Information Center

Philippines Univ., Quezon City. Inst. for Science and Mathematics Education Development.

This module provides instructions for clarifying cooking oil and using it with either wood ash lye or commercial lye to make laundry soap. It also provides (in appendices): a discussion of oils and soaps, including the history of soap; instructions for preparing an 18 percent lye solution; instructions for preparing soap using lye from wood ash;…

40 CFR 417.60 - Applicability; description of the manufacture of soap flakes and powders subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

... manufacture of soap flakes and powders subcategory. 417.60 Section 417.60 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SOAP AND DETERGENT MANUFACTURING POINT SOURCE CATEGORY Manufacture of Soap Flakes and Powders Subcategory § 417.60 Applicability...

40 CFR 417.60 - Applicability; description of the manufacture of soap flakes and powders subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

... manufacture of soap flakes and powders subcategory. 417.60 Section 417.60 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SOAP AND DETERGENT MANUFACTURING POINT SOURCE CATEGORY Manufacture of Soap Flakes and Powders Subcategory § 417.60 Applicability...

40 CFR 417.60 - Applicability; description of the manufacture of soap flakes and powders subcategory.

Code of Federal Regulations, 2013 CFR

2013-07-01

... manufacture of soap flakes and powders subcategory. 417.60 Section 417.60 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SOAP AND DETERGENT MANUFACTURING POINT SOURCE CATEGORY Manufacture of Soap Flakes and Powders Subcategory § 417.60 Applicability...

Inclusions in freely suspended smectic films

NASA Astrophysics Data System (ADS)

Stannarius, Ralf; Harth, Kirsten

Smectic liquid crystal phases have a unique property: Like soap solutions, they can form stable freely suspended films. Their aspect ratios can be larger than one million to one. Such films can serve as models for two-dimensional (2D) uids, with or without in-plane anisotropy. Solid or liquid inclusions trapped in these films by capillary forces can move in the film plane and interact with other inclusions, with film thickness gradients or the film boundaries, and even with the local orientation field. We describe preparation techniques to incorporate particles or droplets in thin smectic films, and optical observation methods. Several aspects make inclusions in freely suspended films interesting research objects: They provide rich information on capillary forces as well as surface and interfacial tensions, they can serve as platforms for hydrodynamic studies in 2D, and they may help to understand coalescence dynamics at the transition from 2D to 3D...

40 CFR 417.30 - Applicability; description of the soap manufacturing by fatty acid neutralization subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 30 2012-07-01 2012-07-01 false Applicability; description of the soap... ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SOAP AND DETERGENT MANUFACTURING POINT SOURCE CATEGORY Soap Manufacturing by Fatty Acid Neutralization Subcategory § 417.30 Applicability...

40 CFR 417.30 - Applicability; description of the soap manufacturing by fatty acid neutralization subcategory.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 30 2013-07-01 2012-07-01 true Applicability; description of the soap... ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SOAP AND DETERGENT MANUFACTURING POINT SOURCE CATEGORY Soap Manufacturing by Fatty Acid Neutralization Subcategory § 417.30 Applicability...

40 CFR 417.30 - Applicability; description of the soap manufacturing by fatty acid neutralization subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 29 2014-07-01 2012-07-01 true Applicability; description of the soap... ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SOAP AND DETERGENT MANUFACTURING POINT SOURCE CATEGORY Soap Manufacturing by Fatty Acid Neutralization Subcategory § 417.30 Applicability...

High Tc superconducting films from metallo-organic precursors

NASA Astrophysics Data System (ADS)

Davison, W. W.; Shyu, S. G.; Buchanan, R. C.

High Tc superconducting films of heavy metal soaps (derived from carboxylic acid precursors) have been prepared on Si and other substrates. The precursors were synthesized and mixed in appropriate molar ratios to form the high Tc compound YBa2Cu3O(7-x), using a high boiling point common solvent base. The precursor solution was deposited by a spin casting technique on the substrates. Film thicknesses of 0.1-1.0 micron were achieved after heat treatment at 550-850 C at not longer than 4 hours. Films were analyzed as to orientation, appropriate phase, interfacial reaction, and superconducting properties.

Preference and compliance of waterless hand-hygiene products versus soap and water.

PubMed

Carr, Michele P; Sullivan, Stefanie; Gilmore, Jenny; Rashid, Robert G

2003-09-01

To compare handwashing using traditional antimicrobial soap and water with two antimicrobial waterless hand-hygiene products for personal preference and compliance. Fifty dental and dental hygiene students were randomly chosen to participate in the study. All subjects were anonymously observed prior to the introduction of the waterless products for handwashing compliance using soap and water for 1 week. All subjects were then instructed on the use of a waterless gel and foam for handwashing. Both waterless products were used for a period of 1 week and students again were anonymously observed. A questionnaire was distributed at the conclusion of the study to determine product preference. During handwashing with soap and water, the average time the soap was in contact with the hands was 7.0 seconds. The average contact time with the gel and foam was 15.3 seconds and 20.0 seconds, respectfully. Questionnaire results indicated that the foam was significantly preferred over the gel and soap and water (54%, 28% and 16%, respectively). The foam was also significantly preferred when evaluating fragrance (52%), kindness to the skin (66%), convenience (64%) and fastest drying time (54%). Results from this study indicate that the waterless foam product was significantly preferred over the waterless gel and traditional soap and water for handwashing procedures. Since handwashing guidelines, regardless of which product used, recommend a minimum of 15 seconds to minimize the number of transient microorganisms on the hands, compliance was found only with the foam and the gel.

Effect of a behaviour-change intervention on handwashing with soap in India (SuperAmma): a cluster-randomised trial.

PubMed

Biran, Adam; Schmidt, Wolf-Peter; Varadharajan, Kiruba Sankar; Rajaraman, Divya; Kumar, Raja; Greenland, Katie; Gopalan, Balaji; Aunger, Robert; Curtis, Val

2014-03-01

Diarrhoea and respiratory infections are the two biggest causes of child death globally. Handwashing with soap could substantially reduce diarrhoea and respiratory infections, but prevalence of adequate handwashing is low. We tested whether a scalable village-level intervention based on emotional drivers of behaviour, rather than knowledge, could improve handwashing behaviour in rural India. The study was done in Chittoor district in southern Andhra Pradesh, India, between May 24, 2011, and Sept 10, 2012. Eligible villages had a population of 700-2000 people, a state-run primary school for children aged 8-13 years, and a preschool for children younger than 5 years. 14 villages (clusters) were selected, stratified by population size (<1200 vs >1200), and randomly assigned in a 1:1 ratio to intervention or control (no intervention). Clusters were enrolled by the study manager. Random allocation was done by the study statistician using a random number generator. The intervention included community and school-based events incorporating an animated film, skits, and public pledging ceremonies. Outcomes were measured by direct observation in 20-25 households per village at baseline and at three follow-up visits (6 weeks, 6 months, and 12 months after the intervention). Observers had no connection with the intervention and observers and participant households were told that the study was about domestic water use to reduce the risk of bias. No other masking was possible. The primary outcome was the proportion of handwashing with soap at key events (after defecation, after cleaning a child's bottom, before food preparation, and before eating) at all follow-up visits. The control villages received a shortened version of the intervention before the final follow-up round. Outcome data are presented as village-level means. Handwashing with soap at key events was rare at baseline in both the intervention and control groups (1% [SD 1] vs 2% [1]). At 6 weeks' follow-up, handwashing

AIDS soap opera generates massive interest. Eye witness: Cote d'Ivoire.

PubMed

Dodd, R

1995-12-01

SIDA Dans La Cite (AIDS in the City) is a popular weekly soap opera first broadcast in Cote d'Ivoire in 1991 with 11 15-minute episodes. The series is part of a campaign by Population Services International (PSI) to raise awareness about AIDS among Ivorian youth. Actors worked for a nominal fee, editing studios were provided at substantial discounts, and filming equipment was borrowed for next to nothing. Production director realized how important the soap opera had become after the fourth episode. A study of 700 households in Abidjan found that of the 75% who had access to a television, two-thirds had seen at least one episode. Cote d'Ivoire may be one of the most religiously conservative countries in Africa. 10% of the adult population, however, is infected with HIV. All sectors of society therefore understand the need to openly understand and discuss sexual issues in the context of such high HIV prevalence. Studies indicate that virtually everyone in Cote d'Ivoire has heard of AIDS and knows that it is a sexually transmitted disease, but persuading people to change their behavior is difficult. PSI sells approximately 750,000 of its subsidized Prudence condoms. Prudence has the same brand recognition in the country as Nescafe and Toyota. A recent survey of sexually active teens found that 30% of girls and 45% of boys used condoms. A weekly radio show is broadcast live from one of the poorest ghettos of Abidjan. Guests include popular singers, comedians, and television personalities. The actors are often from SIDA Dans La Cite.

Resonance tunneling electron-vibrational spectroscopy of polyoxometalates.

PubMed

Dalidchik, F I; Kovalevskii, S A; Balashov, E M

2017-05-21

The tunneling spectra of the ordered monolayer films of decamolybdodicobaltate (DMDC) compounds deposited from aqueous solutions on HOPG were measured by scanning tunnel microscopy in air. The DMDC spectra, as well as the tunneling spectra of other polyoxometalates (POMs), exhibit well-defined negative differential resistances (NDRs). The mechanism of formation of these spectral features was established from the collection of revealed NDR dependences on the external varying parameters and found to be common to all systems exhibiting Wannier-Stark localization. A model of biresonance tunneling was developed to provide an explanation for the totality of experimental data, both the literature and original, on the tunneling POM probing. A variant of the tunneling electron-vibrational POM spectroscopy was proposed allowing the determination of the three basic energy parameters-energy gaps between the occupied and unoccupied states, frequencies of the vibrational transitions accompanying biresonance electron-tunneling processes, and electron-vibrational interaction constants on the monomolecular level.

Resonance tunneling electron-vibrational spectroscopy of polyoxometalates

PubMed Central

Dalidchik, F. I.; Kovalevskii, S. A.

2017-01-01

The tunneling spectra of the ordered monolayer films of decamolybdodicobaltate (DMDC) compounds deposited from aqueous solutions on HOPG were measured by scanning tunnel microscopy in air. The DMDC spectra, as well as the tunneling spectra of other polyoxometalates (POMs), exhibit well-defined negative differential resistances (NDRs). The mechanism of formation of these spectral features was established from the collection of revealed NDR dependences on the external varying parameters and found to be common to all systems exhibiting Wannier–Stark localization. A model of biresonance tunneling was developed to provide an explanation for the totality of experimental data, both the literature and original, on the tunneling POM probing. A variant of the tunneling electron-vibrational POM spectroscopy was proposed allowing the determination of the three basic energy parameters—energy gaps between the occupied and unoccupied states, frequencies of the vibrational transitions accompanying biresonance electron-tunneling processes, and electron-vibrational interaction constants on the monomolecular level. PMID:28527451

Human health risk assessment of chloroxylenol in liquid hand soap and dishwashing soap used by consumers and health-care professionals.

PubMed

Yost, Lisa J; Rodricks, Joseph D; Turnbull, Duncan; DeLeo, Paul C; Nash, J Frank; Quiñones-Rivera, Antonio; Carlson, Pete A

2016-10-01

A quantitative human risk assessment of chloroxylenol was conducted for liquid hand and dishwashing soap products used by consumers and health-care workers. The toxicological data for chloroxylenol indicate lack of genotoxicity, no evidence of carcinogenicity, and minimal systemic toxicity. No observed adverse effect levels (NOAEL) were established from chronic toxicity studies, specifically a carcinogenicity study that found no cancer excess (18 mg/kg-day) and studies of developmental and reproductive toxicity (100 mg/kg-day). Exposure to chloroxylenol for adults and children was estimated for two types of rinse-off cleaning products, one liquid hand soap, and two dishwashing products. The identified NOAELs were used together with exposure estimates to derive margin of exposure (MOE) estimates for chloroxylenol (i.e., estimates of exposure over NOAELs). These estimates were designed with conservative assumptions and likely overestimate exposure and risk (i.e., highest frequency, 100% dermal penetration). The resulting MOEs ranged from 178 to over 100, 000, 000 indicating negligibly small potential for harm related to consumer or health-care worker exposure to chloroxylenol in liquid soaps used in dish washing and hand washing. Copyright © 2016 Elsevier Inc. All rights reserved.

40 CFR 417.30 - Applicability; description of the soap manufacturing by fatty acid neutralization subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 29 2011-07-01 2009-07-01 true Applicability; description of the soap manufacturing by fatty acid neutralization subcategory. 417.30 Section 417.30 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SOAP AND DETERGENT MANUFACTURING POINT SOURCE CATEGORY Soap...

Child toy safety: An interdisciplinary approach to unravel the microbiological hazard posed by soap bubbles.

PubMed

Amoruso, Irene; Bertoncello, Chiara; Caravello, Gianumberto; Giaccone, Valerio; Baldovin, Tatjana

2015-11-01

In 2012 some children developed sepsis after playing together with a soap bubble toy. Microbiological testing revealed heavy contamination of the soap solution, which reasonably represented the vehicle of infection. We investigated the issue with a multidisciplinary approach: review of toy safety legislation; microbiological testing of additional samples; query of the RAPEX database for non-compliant soap bubbles; identification of major manufacturing districts. Microbiological contamination of industrial soap bubbles was widespread. Sixty-three notifications of batches contaminated by environmental microorganisms and opportunistic pathogens had been reported. The Chinese had a virtual monopoly of the soap bubble market. We identified two main manufacturing districts in Guangdong Province, both notable for degradation of their water resources. The use of untreated water for the industrial production of soap bubbles may explain the bacterial contamination. Existing legislation provides an unsatisfactory approach for managing microbiological hazards in sensitive toy categories and for identifying responsible parties in import and export of the products.

TCP/IP Interface for the Satellite Orbit Analysis Program (SOAP)

NASA Technical Reports Server (NTRS)

Carnright, Robert; Stodden, David; Coggi, John

2009-01-01

The Transmission Control Protocol/ Internet protocol (TCP/IP) interface for the Satellite Orbit Analysis Program (SOAP) provides the means for the software to establish real-time interfaces with other software. Such interfaces can operate between two programs, either on the same computer or on different computers joined by a network. The SOAP TCP/IP module employs a client/server interface where SOAP is the server and other applications can be clients. Real-time interfaces between software offer a number of advantages over embedding all of the common functionality within a single program. One advantage is that they allow each program to divide the computation labor between processors or computers running the separate applications. Secondly, each program can be allowed to provide its own expertise domain with other programs able to use this expertise.

Induced Superconductivity and Engineered Josephson Tunneling Devices in Epitaxial (111)-Oriented Gold/Vanadium Heterostructures.

PubMed

Wei, Peng; Katmis, Ferhat; Chang, Cui-Zu; Moodera, Jagadeesh S

2016-04-13

We report a unique experimental approach to create topological superconductors by inducing superconductivity into epitaxial metallic thin film with strong spin-orbit coupling. Utilizing molecular beam epitaxy technique under ultrahigh vacuum conditions, we are able to achieve (111) oriented single phase of gold (Au) thin film grown on a well-oriented vanadium (V) s-wave superconductor film with clean interface. We obtained atomically smooth Au thin films with thicknesses even down to below a nanometer showing near-ideal surface quality. The as-grown V/Au bilayer heterostructure exhibits superconducting transition at around 3.9 K. Clear Josephson tunneling and Andreev reflection are observed in S-I-S tunnel junctions fabricated from the epitaxial bilayers. The barrier thickness dependent tunneling and the associated subharmonic gap structures (SGS) confirmed the induced superconductivity in Au (111), paving the way for engineering thin film heterostructures based on p-wave superconductivity and nano devices exploiting Majorana Fermions for quantum computing.

The Appeal of Soap Opera.

ERIC Educational Resources Information Center

Kielwasser, Alfred P.; Wolf, Michelle A.

This paper provides a framework for developing an approach to understanding soap opera's appeal as a direct function of both the genre's form and of its fans' viewing behavior. The paper suggests that while this analysis is largely critical, other studies from both critical and social scientific approaches can be based upon the framework and…

40 CFR 417.60 - Applicability; description of the manufacture of soap flakes and powders subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 29 2011-07-01 2009-07-01 true Applicability; description of the manufacture of soap flakes and powders subcategory. 417.60 Section 417.60 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SOAP AND DETERGENT MANUFACTURING POINT SOURCE CATEGORY Manufacture of Soap...

40 CFR 417.60 - Applicability; description of the manufacture of soap flakes and powders subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 28 2010-07-01 2010-07-01 true Applicability; description of the manufacture of soap flakes and powders subcategory. 417.60 Section 417.60 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SOAP AND DETERGENT MANUFACTURING POINT SOURCE CATEGORY Manufacture of Soap...

Soap production: A green prospective.

PubMed

Félix, Sandra; Araújo, Joana; Pires, Ana Maria; Sousa, Ana Cláudia

2017-08-01

A green prospective based on the reuse of waste materials such as almond shells, orange peel and used cooking oil to manufacture soap is presented. In Portugal, thousands of tons of waste are generated from used cooking oil and production of nut shells' residues is growing every year. In addition, the high consumption of citrus fruits, oranges in particular, generates large amounts of citrus peel. Therefore, it is necessary to diversify reuse mechanisms of these wastes, in order to make them back into raw materials. Complying with this trend, this work was carried out by processing and grinding almond shells, treating used oil, processing orange peels and extracting limonene, formulating and producing soap, and performing an acceptance study of the final product. Results validated a high potential of the idea in the field of environmental education, so it can be replicated in practical classes. It can also be useful for waste management, and it can support the development of community projects on an ecological approach. Copyright © 2017 Elsevier Ltd. All rights reserved.

Soap is not enough: handwashing practices and knowledge in refugee camps, Maban County, South Sudan.

PubMed

Phillips, Raina M; Vujcic, Jelena; Boscoe, Andrew; Handzel, Thomas; Aninyasi, Mark; Cookson, Susan T; Blanton, Curtis; S Blum, Lauren; Ram, Pavani K

2015-01-01

Refugees are at high risk for communicable diseases due to overcrowding and poor water, sanitation, and hygiene conditions. Handwashing with soap removes pathogens from hands and reduces disease risk. A hepatitis E outbreak in the refugee camps of Maban County, South Sudan in 2012 prompted increased hygiene promotion and improved provision of soap, handwashing stations, and latrines. We conducted a study 1 year after the outbreak to assess the knowledge, attitudes, and practices of the refugees in Maban County. We conducted a cross sectional survey of female heads of households in three refugee camps in Maban County. We performed structured observations on a subset of households to directly observe their handwashing practices at times of possible pathogen transmission. Of the 600 households interviewed, nearly all had soap available and 91 % reported water was available "always" or "sometimes". Exposure to handwashing promotion was reported by 85 % of the respondents. Rinsing hands with water alone was more commonly observed than handwashing with soap at critical handwashing times including "before eating" (80 % rinsing vs. 7 % washing with soap) and "before preparing/cooking food" (72.3 % vs 23 %). After toilet use, 46 % were observed to wash hands with soap and an additional 38 % rinsed with water alone. Despite intensive messaging regarding handwashing with soap and access to soap and water, rinsing hands with water alone rather than washing hands with soap remains more common among the refugees in Maban County. This practice puts them at continued risk for communicable disease transmission. Qualitative research into local beliefs and more effective messaging may help future programs tailor handwashing interventions.

A 350 mK, 9 T scanning tunneling microscope for the study of superconducting thin films on insulating substrates and single crystals.

PubMed

Kamlapure, Anand; Saraswat, Garima; Ganguli, Somesh Chandra; Bagwe, Vivas; Raychaudhuri, Pratap; Pai, Subash P

2013-12-01

We report the construction and performance of a low temperature, high field scanning tunneling microscope (STM) operating down to 350 mK and in magnetic fields up to 9 T, with thin film deposition and in situ single crystal cleaving capabilities. The main focus lies on the simple design of STM head and a sample holder design that allows us to get spectroscopic data on superconducting thin films grown in situ on insulating substrates. Other design details on sample transport, sample preparation chamber, and vibration isolation schemes are also described. We demonstrate the capability of our instrument through the atomic resolution imaging and spectroscopy on NbSe2 single crystal and spectroscopic maps obtained on homogeneously disordered NbN thin film.

Role of Coulomb blockade and spin-flip scattering in tunneling magnetoresistance of FeCo-Si-O nanogranular films

NASA Astrophysics Data System (ADS)

Kumar, Hardeep; Ghosh, Santanu; Bürger, Danilo; Li, Lin; Zhou, Shengqiang; Kabiraj, Debdulal; Avasthi, Devesh Kumar; Grötzschel, Rainer; Schmidt, Heidemarie

2011-04-01

In this work, we report the effect of FeCo atomic fraction (0.33 < x < 0.54) and temperature on the electrical, magnetic, and tunneling magnetoresistance (TMR) properties of FeCo-Si-O granular films prepared by atom beam sputtering technique. Glancing angle x-ray diffraction and TEM studies reveal that films are amorphous in nature. The dipole-dipole interactions (particle-matrix mixing) is evident from zero-field cooled and field-cooled magnetic susceptibility measurements and the presence of oxides (mainly Fe-related) is observed by x-ray photoelectron spectroscopy analysis. The presence of Fe-oxides is responsible for the observed reduction of saturation magnetization and rapid increase in coercivity below 50 K. TMR has been observed in a wide temperature range, and a maximum TMR of -4.25% at 300 K is observed for x = 0.39 at a maximum applied field of 60 kOe. The fast decay of maximum TMR at high temperatures and lower TMR values at 300 K when compared to PFeCo2/(1+PFeCo2), where PFeCo is the spin polarization of FeCo are in accordance with a theoretical model that includes spin-flip scattering processes. The temperature dependent study of TMR effect reveals a remarkably enhanced TMR at low temperatures. The TMR value varies from -2.1% at 300 K to -14.5% at 5 K for x = 0.54 and a large MR value of -18.5% at 5 K for x = 0.39 is explained on the basis of theoretical models involving Coulomb blockade effects. Qualitatively particle-matrix mixing and the presence of Fe-oxides seems to be the source of spin-flip scattering, responsible for fast decay of TMR at high temperatures. A combination of higher order tunneling (in Coulomb blockade regime) and spin-flip scattering (high temperature regime) explains the temperature dependent TMR of these films.

Evaluation of proposed Skylab and SSP soap products.

NASA Technical Reports Server (NTRS)

Durfee, R. L.; Spurlock, J. M.; Whitmore, F. C.

1973-01-01

Four candidate cleansing agents evaluated in terms of potential hazards to crew members included two soaps (Neutrogena bar soap and Olive Leaf Liquid), one nonfoaming surfactant (Miranol JEM), and one laundry detergent (sodium dodecylbenzene sulfonate). None of the four exhibited adverse dermatological effects from skin patch tests or supported growth of potentially pathogenic microorganisms. Aqueous solutions of Neutrogena did support a mold species. Neutrogena and Miranol JEM were used in a simulated Skylab personal hygiene regimen with no adverse effects on skin or skin microflora. Based on our results, each of these agents appear to be a promising candidate material for the use intended.

Rapid antibacterial activity of 2 novel hand soaps: evaluation of the risk of development of bacterial resistance to the antibacterial agents.

PubMed

Geraldo, Ingrid M; Gilman, Allan; Shintre, Milind S; Modak, Shanta M

2008-08-01

To evaluate the antimicrobial efficacy of and risk of organisms developing resistance to 2 novel hand soaps: (1) a soap containing triclosan, polyhexamethylene biguanide, and benzethonium chloride added to a soap base (TPB soap); and (2) a soap containing farnesol, polyhexamethylene biguanide, and benzethonium chloride added to a soap base (FPB soap). Tests also included soaps containing only triclosan. The risk of emergence of resistant bacterial mutants was investigated by determining the susceptibility changes after repeated exposure of bacteria to the drugs and soaps in vitro. The effectiveness of the soaps was evaluated using an in vitro tube dilution method, a volunteer method (the ASTM standard), and 2 pig skin methods. The minimum inhibitory concentration and minimum bactericidal concentration of triclosan against Staphylococcus aureus increased 8- to 62.5-fold, whereas those of TPB and FPB (both alone and in soap) were unchanged. In vitro, TPB and FPB soaps produced higher log(10) reductions in colony-forming units of all tested organisms (4.95-8.58) than did soaps containing triclosan alone (0.29-4.86). In the test using the pig skin and volunteer methods, TPB soap produced a higher log(10) reduction in colony-forming units (3.1-3.3) than did the soap containing triclosan alone (2.6-2.8). The results indicate that TPB and FPB soaps may provide superior rapid and broad-spectrum efficacy with a lower risk of organisms developing resistance than do soaps containing triclosan alone. Pig skin methods may be used to predict the efficacy of antibacterial soaps in the rapid disinfection of contaminated hands. Hand washing with TPB and FPB soaps by healthcare workers and the general population may reduce the transmission of pathogens, with a lower risk of promoting the emergence of resistant organisms.

Engineering and characterizing inverse tunneling magnetoresistance magnetic tunnel junctions with novel ferromagnetic electrodes

NASA Astrophysics Data System (ADS)

Xiang, Hua

Magnetic tunnel junctions (MTJs) have attracted great interest for applications in read heads and nonvolatile magnetic random access memories. MTJs exhibit tunneling magnetoresistance (TMR), which is proportional to the spin polarization (SP) of ferromagnetic (FM) electrodes. This thesis describes the fabrication and characterization of inverse TMR MTJs with novel FM electrodes and tunnel barriers, including Fe3O4 and Fe4N electrodes and Ta2O5 tunnel barriers. Fe3O4 has been predicted to have perfect negative SP at the Fermi level, making it a promising FM electrode for inverse TMR MTJs. Two approaches were developed to grow epitaxial Fe3O 4 films on Si substrates, reactive sputtering and selective oxidation, and the physical properties were characterized. Epitaxial Fe3O 4 films with smooth surfaces were achieved using a TiN buffer and low temperature selective oxidation. Fe4N has also been predicted to have nearly perfect negative SP. Epitaxial Fe4N films were fabricated on Si substrates by reactive sputtering, and the magnetic properties and thermal stability were characterized. Fe4N is metastable with respect to decomposition into Fe and N 2. During room temperature air oxidation, an epitaxial Fe3O 4 layer formed on Fe4N surface, by incorporation of oxygen, decomposition of Fe4N, and release of N. We fabricated Fe4N/AlOx/Fe MTJs and found normal TMR for the as-prepared junction but inverse TMR with abnormal bias dependence after annealing. The TMR inversion is caused by an Fe3O4 layer at the Fe4N/AlO, interface. The abnormal bias dependence is caused by an imperfect Fe3O4/AlOx interface. Fe3O4 (or Fe4N)/Ta2O5/Fe MTJs show relatively low junction resistance and noisy TMR signals, due to the difficulty of preparing high quality Ta2O5 barriers. The effect of composition of bcc Co100-xFex electrodes on the TMR for AlOx-based MTJs has been studied. The TMR increases with x until it reaches a maximum of 66.7% at 28 at.% Fe, and then decreases. The reason for this TMR

A meta-analysis of the published literature on the effectiveness of antimicrobial soaps.

PubMed

Montville, Rebecca; Schaffner, Donald W

2011-11-01

The goal of this research was to conduct a systematic quantitative analysis of the existing data in the literature in order to determine if there is a difference between antimicrobial and nonantimicrobial soaps and to identify the methodological factors that might affect this difference. Data on hand washing efficacy and experimental conditions (sample size, wash duration, soap quantity, challenge organism, inoculum size, and neutralization method) from published studies were compiled and transferred to a relational database. A total of 25 publications, containing 374 observations, met the study selection criteria. The majority of the studies included fewer than 15 observations with each treatment and included a direct comparison between nonantimicrobial soap and antimicrobial soap. Although differences in efficacy between antimicrobial and nonantimicrobial soap were small (∼0.5-log CFU reduction difference), antimicrobial soap produced consistently statistically significantly greater reductions. This difference was true for any of the antimicrobial compounds investigated where n was >20 (chlorhexidine gluconate, iodophor, triclosan, or povidone). Average log reductions were statistically significantly greater (∼2 log CFU) when either gram-positive or gram-negative transient organisms were deliberately added to hands compared with experiments done with resident hand flora (∼0.5 log CFU). Our findings support the importance of using a high initial inoculum on the hands, well above the detection limit. The inherent variability in hand washing seen in the published literature underscores the importance of using a sufficiently large sample size to detect differences when they occur.

Antimicrobial Activity of Medicated Soaps Commonly Used By Dar es Salaam Residents in Tanzania

PubMed Central

Mwambete, K. D.; Lyombe, F.

2011-01-01

An in vitro evaluation of the anti-microbial activity of medicated soaps was conducted using ditch-plate and hand washing techniques. Strains of reference microbes namely Candida albicans (ATCC90028), Staphylococcus aureus (ATCC25923), Pseudomonas aureginosa (ATCC27853) and Escherichia coli (ATCC25922) were tested at three different soaps’ concentrations (1.0, 4.0 and 8.0 mg/ml). A total of 16 medicated soaps were assayed for their antimicrobial efficacy. Of these, 13 were medicated and 3 non-medicated soaps, which served as control. Ciprofloxacin and ketaconazole were employed as positive controls. Label disclosure for the soaps’ ingredients and other relevant information were absorbed. The most common antimicrobial active ingredients were triclosan, trichloroxylenol and trichlorocarbanilide. ANOVA for means of zones of inhibition revealed variability of antimicrobial activity among the medicated soaps. Positive correlation (r=0.318; P<0.01) between zones of inhibition and soaps’ concentrations was evidenced. Hand washing frequencies positively correlated with microbial counts. Roberts® soap exhibited the largest zone of inhibition (34 mm) on S. aureus. Candida albicans was the least susceptible microbe. Regency® and Dalan® exhibited the least zone of inhibition on the tested bacteria. Protex®, Roberts®, Family® and Protector® were equally effective (P<0.01) against S. aureus. In conclusion, majority of the assayed medicated soaps have satisfactory antibacterial activity; though lack antifungal effect with exception of Linda® liquid soap. The hand washing technique has proved to be inappropriate for evaluation of soaps’ antimicrobial efficacy due to presence of the skin microflora. PMID:22131630

Selective scanning tunneling microscope light emission from rutile phase of VO2.

PubMed

Sakai, Joe; Kuwahara, Masashi; Hotsuki, Masaki; Katano, Satoshi; Uehara, Yoichi

2016-09-28

We observed scanning tunneling microscope light emission (STM-LE) induced by a tunneling current at the gap between an Ag tip and a VO2 thin film, in parallel to scanning tunneling spectroscopy (STS) profiles. The 34 nm thick VO2 film grown on a rutile TiO2 (0 0 1) substrate consisted of both rutile (R)- and monoclinic (M)-structure phases of a few 10 nm-sized domains at room temperature. We found that STM-LE with a certain photon energy of 2.0 eV occurs selectively from R-phase domains of VO2, while no STM-LE was observed from M-phase. The mechanism of STM-LE from R-phase VO2 was determined to be an interband transition process rather than inverse photoemission or inelastic tunneling processes.

Comparison of European ICU patients in 2012 (ICON) versus 2002 (SOAP).

PubMed

Vincent, Jean-Louis; Lefrant, Jean-Yves; Kotfis, Katarzyna; Nanchal, Rahul; Martin-Loeches, Ignacio; Wittebole, Xavier; Sakka, Samir G; Pickkers, Peter; Moreno, Rui; Sakr, Yasser

2018-03-01

To evaluate differences in the characteristics and outcomes of intensive care unit (ICU) patients over time. We reviewed all epidemiological data, including comorbidities, types and severity of organ failure, interventions, lengths of stay and outcome, for patients from the Sepsis Occurrence in Acutely ill Patients (SOAP) study, an observational study conducted in European intensive care units in 2002, and the Intensive Care Over Nations (ICON) audit, a survey of intensive care unit patients conducted in 2012. We compared the 3147 patients from the SOAP study with the 4852 patients from the ICON audit admitted to intensive care units in the same countries as those in the SOAP study. The ICON patients were older (62.5 ± 17.0 vs. 60.6 ± 17.4 years) and had higher severity scores than the SOAP patients. The proportion of patients with sepsis at any time during the intensive care unit stay was slightly higher in the ICON study (31.9 vs. 29.6%, p = 0.03). In multilevel analysis, the adjusted odds of ICU mortality were significantly lower for ICON patients than for SOAP patients, particularly in patients with sepsis [OR 0.45 (0.35-0.59), p < 0.001]. Over the 10-year period between 2002 and 2012, the proportion of patients with sepsis admitted to European ICUs remained relatively stable, but the severity of disease increased. In multilevel analysis, the odds of ICU mortality were lower in our 2012 cohort compared to our 2002 cohort, particularly in patients with sepsis.

Tunneling contact IGZO TFTs with reduced saturation voltages

NASA Astrophysics Data System (ADS)

Wang, Longyan; Sun, Yin; Zhang, Xintong; Zhang, Lining; Zhang, Shengdong; Chan, Mansun

2017-04-01

We report a tunneling contact indium-gallium-zinc oxide (IGZO) thin film transistor (TFT) with a graphene interlayer technique in this paper. A Schottky junction is realized between a metal and IGZO with a graphene interlayer, leading to a quantum tunneling of the TFT transport in saturation regions. This tunneling contact enables a significant reduction in the saturation drain voltage Vdsat compared to that of the thermionic emission TFTs, which is usually equal to the gate voltage minus their threshold voltages. Measured temperature independences of the subthreshold swing confirm a transition from the thermionic emission to quantum tunneling transports depending on the gate bias voltages in the proposed device. The tunneling contact TFTs with the graphene interlayer have implications to reduce the power consumptions of certain applications such as the active matrix OLED display.

16. 3RD FLOOR, J.M. LEHMANN CO. FIVEROLL TOILET SOAP MILL ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

16. 3RD FLOOR, J.M. LEHMANN CO. FIVE-ROLL TOILET SOAP MILL INSTALLED 1950, TO WEST; BUCKET CONVEYOR AT RIGHT MOVED WASTE FROM 2ND FLOOR SOAP PRESSES TO 5TH FLOOR RE-MANUFACTURE - Colgate & Company Jersey City Plant, Building No. B-14, 54-58 Grand Street, Jersey City, Hudson County, NJ

SOAP Methodology in General Practice/Family Medicine Teaching in Practical Context.

PubMed

Santiago, Luiz Miguel; Neto, Isabel

2016-12-30

Medical records in General Practice/Family Medicine are an essential information support on the health status of the patient and a communication document between health professionals. The development of competencies in General Practice/Family Medicine during pre-graduation must include the ability to make adequate medical records in practical context. As of 2012, medicine students at the University of Beira Interior have been performing visits using the Subjective, Objective, Assessment and Plan - SOAP methodology, with a performance evaluation of the visit, with the aim to check on which Subjective, Objective, Assessment and Plan - SOAP aspects students reveal the most difficulties in order to define improvement techniques and to correlate patient grade with tutor evaluation. Analysing the evaluation data for the 2015 - 2016 school year at the General Practice/Family Medicine visit carried out by fourth year students in medicine, comparing the averages of each item in the Subjective, Objective, Assessment and Plan - SOAP checklist and the patient evaluation. In the Subjective, Objective, Assessment and Plan - SOAP, 29.7% of students are on the best grade quartile, 37.1% are on the best competencies quartile and 27.2% on the best patient grade quartile. 'Evolution was verified/noted' received the worst grades in Subjective, 'Record of physical examination focused on the problem of the visit' received the worst grades in Objective, 'Notes of Diagnostic reasoning / differential diagnostic' received de worst grades in Assessment and 'Negotiation of aims to achieve' received the worst grades in Plan. The best tutor evaluation is found in 'communication'. Only one single study evaluated student´s performance under examination during a visit, with similar results to the present one and none addressed the patient's evaluation. Students revealed a good performance in using the Subjective, Objective, Assessment and Plan - SOAP. The findings represent the beginning of the

Electrically rotating suspended films of polar liquids

NASA Astrophysics Data System (ADS)

Shirsavar, R.; Amjadi, A.; Tonddast-Navaei, A.; Ejtehadi, M. R.

2011-02-01

Controlled rotation of a suspended soap water film, simply generated by applying an electric field, has been reported recently. The film rotates when the applied electric field exceeds a certain threshold. In this study, we investigate the phenomenon in films made of a number of other liquids with various physical and chemical properties. Our measurements show that the intrinsic electrical dipole moments of the liquid molecules seems to be vital for the corresponding film rotation. All the investigated rotating liquids have a molecular electric dipole moment of above 1 Debye, while weakly polar liquids do not rotate. However, the liquids investigated here cover a wide range of physical parameters (e.g. viscosity, density, conductivity, etc.). So far, no significant correlation has been observed between the electric field thresholds and macroscopic properties of the liquids.

21 CFR 701.20 - Detergent substances, other than soap, intended for use in cleansing the body.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 7 2013-04-01 2013-04-01 false Detergent substances, other than soap, intended... Ingredients § 701.20 Detergent substances, other than soap, intended for use in cleansing the body. (a) In its definition of the term cosmetic, the Federal Food, Drug, and Cosmetic Act specifically excludes soap. The...

21 CFR 701.20 - Detergent substances, other than soap, intended for use in cleansing the body.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 7 2012-04-01 2012-04-01 false Detergent substances, other than soap, intended... Ingredients § 701.20 Detergent substances, other than soap, intended for use in cleansing the body. (a) In its definition of the term cosmetic, the Federal Food, Drug, and Cosmetic Act specifically excludes soap. The...

21 CFR 701.20 - Detergent substances, other than soap, intended for use in cleansing the body.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 7 2014-04-01 2014-04-01 false Detergent substances, other than soap, intended... Ingredients § 701.20 Detergent substances, other than soap, intended for use in cleansing the body. (a) In its definition of the term cosmetic, the Federal Food, Drug, and Cosmetic Act specifically excludes soap. The...

Diagnosis at a glance of biological non-Newtonian fluids with Film Interference Flow Imaging (FIFI)

NASA Astrophysics Data System (ADS)

Hidema, R.; Yamada, N.; Furukawa, H.

2012-04-01

In the human body, full of biological non-Newtonian fluids exist. For example, synovial fluids exist in our joints, which contain full of biopolymers, such as hyaluronan and mucin. It is thought that these polymers play critical roles on the smooth motion of the joint. Indeed, luck of biopolymers in synovial fluid cause joint pain. Here we study the effects of polymer in thin liquid layer by using an original experimental method called Film Interference Flow Imaging (FIFI). A vertically flowing soap film containing polymers is made as two-dimensional flow to observe turbulence. The thickness of water layer is about 4 μm sandwiched between surfactant mono-layers. The interference pattern of the soap film is linearly related to the flow velocity in the water layer through the change in the thickness of the film. Thus the flow velocity is possibly analyzed by the single image analysis of the interference pattern, that is, FIFI. The grid turbulence was made in the flowing soap films containing the long flexible polymer polyethyleneoxide (PEO, Mw=3.5x106), and rigid polymer hydroxypropyl cellulose (HPC, Mw > 1.0 x106). The decaying process of the turbulence is affected by PEO and HPC at several concentrations. The effects of PEO are sharply seen even at low concentrations, while the effects of HPC are gradually occurred at much higher concentration compared to the PEO. It is assumed that such a difference between PEO and HPC is due to the polymer stretching or polymer orientation under turbulence, which is observed and analyzed by FIFI. We believe the FIFI will be applied in the future to examine biological fluids such as synovial fluids quickly and quantitatively.

[Identification of bacterial contamination in liquid soap for hospital use].

PubMed

Caetano, Joselany Afio; Lima, Maria Alzete; Di Ciero Miranda, Maira; Serufo, José Carlos; Ponte, Paulo Roberto Lins

2011-03-01

This study performed a bacteriological analysis of the liquid soap in dispensers that health professionals use for hand washing. This exploratory, cross-sectional study was developed at the hospitalization units of a medium-sized hospital in Fortaleza, Ceará, Brazil. Data were collected between May and July 2007. Fifty-nine liquid soap dispensers were analyzed, of which 33 contained the following microorganisms: Burkholderia cepacia (14), Pseudomonas putidas (9), Pseudomonas aeruginosa (3), Klebsiella pneumoniae (3), Enterobacter clocae (2), and Pseudomonas luteola (2). The units with the largest number of contaminated samples were the surgical (n=7) and the dermatological clinics (n=4). Contamination was also found in an original flask of the same lot of liquid soap used to fill up the dispensers. In conclusion, there is a need to regulate and control the quality of these products in the production lines as well as during use in hospital services, mainly because they are used to prevent hospital infection.

40 CFR 430.03 - Best management practices (BMPs) for spent pulping liquor, soap, and turpentine management, spill...

Code of Federal Regulations, 2014 CFR

2014-07-01

... spent pulping liquor, soap, and turpentine management, spill prevention, and control. 430.03 Section 430... management practices (BMPs) for spent pulping liquor, soap, and turpentine management, spill prevention, and... Liquor, Soap, and Turpentine Service: Any process vessel, storage tank, pumping system, evaporator, heat...

40 CFR 430.03 - Best management practices (BMPs) for spent pulping liquor, soap, and turpentine management, spill...

Code of Federal Regulations, 2013 CFR

2013-07-01

... spent pulping liquor, soap, and turpentine management, spill prevention, and control. 430.03 Section 430... management practices (BMPs) for spent pulping liquor, soap, and turpentine management, spill prevention, and... Liquor, Soap, and Turpentine Service: Any process vessel, storage tank, pumping system, evaporator, heat...

10. 4TH FLOOR, HOTEL SOAP LINE No. 6 TO SOUTHWEST, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

10. 4TH FLOOR, HOTEL SOAP LINE No. 6 TO SOUTHWEST, WITH AUTOMATIC CUTTER (LEFT), PRESS (CENTER), AND WRAPPER (RIGHT); LARGE CHUTE AT CENTER FROM 5TH FLOOR BINS TO 3RD FLOOR SOAP MILLS; OVERHEAD AND FLOOR (LOWER RIGHT) FINISHED GOODS CONVEYORS TO G BLOCK (HAER NO. NJ-71-NN) - Colgate & Company Jersey City Plant, Building No. B-14, 54-58 Grand Street, Jersey City, Hudson County, NJ

Effect of tunneling layers on the performances of floating-gate based organic thin-film transistor nonvolatile memories

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Wei, E-mail: wwei99@jlu.edu.cn; Han, Jinhua; Ying, Jun

2014-09-22

Two types of floating-gate based organic thin-film transistor nonvolatile memories (FG-OTFT-NVMs) were demonstrated, with poly(methyl methacrylate co glycidyl methacrylate) (P(MMA-GMA)) and tetratetracontane (TTC) as the tunneling layer, respectively. Their device performances were measured and compared. In the memory with a P(MMA-GMA) tunneling layer, typical unipolar hole transport was obtained with a relatively small mobility of 0.16 cm{sup 2}/V s. The unidirectional shift of turn-on voltage (V{sub on}) due to only holes trapped/detrapped in/from the floating gate resulted in a small memory window of 12.5 V at programming/erasing voltages (V{sub P}/V{sub E}) of ±100 V and a nonzero reading voltage. Benefited from the well-ordered moleculemore » orientation and the trap-free surface of TTC layer, a considerably high hole mobility of 1.7 cm{sup 2}/V s and a visible feature of electrons accumulated in channel and trapped in floating-gate were achieved in the memory with a TTC tunneling layer. High hole mobility resulted in a high on current and a large memory on/off ratio of 600 at the V{sub P}/V{sub E} of ±100 V. Both holes and electrons were injected into floating-gate and overwritten each other, which resulted in a bidirectional V{sub on} shift. As a result, an enlarged memory window of 28.6 V at the V{sub P}/V{sub E} of ±100 V and a zero reading voltage were achieved. Based on our results, a strategy is proposed to optimize FG-OTFT-NVMs by choosing a right tunneling layer to improve the majority carrier mobility and realize ambipolar carriers injecting and trapping in the floating-gate.« less

Thin Film Interference: An Experiment with Microwaves and Paraffin Oil

ERIC Educational Resources Information Center

D'Anna, Michele; Corridoni, Tommaso

2015-01-01

Thin film interference manifests itself in a wide range of visually pleasing situations in everyday life (in the colored effects caused by a drop of oil on water, in soap bubbles, etc.) and is also involved in important technical applications (semi-reflecting mirrors, anti-reflection lenses, etc.). Yet, despite its familiarity, high school…

Viscosity of particle laden films

NASA Astrophysics Data System (ADS)

Timounay, Yousra; Rouyer, Florence

2017-06-01

We perform retraction experiments on soap films where large particles bridge the two interfaces. Local velocities are measured by PIV during the unstationnary regime. The velocity variation in time and space can be described by a continuous fluid model from which effective viscosity (shear and dilatational) of particulate films is measured. The 2D effective viscosity of particulate films η2D increases with particle surface fraction ϕ: at low ϕ, it tends to the interfacial dilatational viscosity of the liquid/air interfaces and it diverges at the critical particle surface fraction ϕc ≃ 0.84. Experimental data agree with classical viscosity laws of hard spheres suspensions adapted to the 2D geometry, assuming viscous dissipation resulting from the squeeze of the liquid/air interfaces between the particles. Finally, we show that the observed viscous dissipation in particulate films has to be considered to describe the edge velocity during a retraction experiment at large particle coverage.

Thermotropic phase behavior of choline soaps.

PubMed

Klein, Regina; Dutton, Helen; Diat, Olivier; Tiddy, Gordon J T; Kunz, Werner

2011-04-14

Choline carboxylates (ChCm with m = 12-18) are simple biocompatible anionic surfactants with very low Krafft temperatures, possessing a rich aqueous phase behavior. In the present work, we have investigated the thermotropic mesomorphism of anhydrous ChCm salts for m = 12-18. Transition temperatures and enthalpies determined by differential scanning calorimetry reveal that all investigated compounds exhibit three different phases between -20 and 95 °C. The phases were further characterized by optical polarizing microscopy, NMR spin-spin relaxation, and X-ray scattering measurements. The nature of the phases was identified with increasing temperature as crystalline, semicrystalline, and liquid-crystalline lamellar. Even long-chain choline carboxylates (m = 18) were found to melt into a lamellar liquid-crystalline phase below 100 °C. Accordingly, with choline as counterion in simple fatty acid soaps, not only the water solubility is considerably enhanced but also the melting points are substantially reduced, hence facilitating thermotropic mesomorphism at temperatures between 35 and 95 °C. Thus, simple choline soaps with m = 12-18 may be classified as ionic liquids.

Hand soap contamination by Pseudomonas aeruginosa in a tertiary care hospital: no evidence of impact on patients.

PubMed

Blanc, D S; Gomes Magalhaes, B; Abdelbary, M; Prod'hom, G; Greub, G; Wasserfallen, J B; Genoud, P; Zanetti, G; Senn, L

2016-05-01

During an environmental investigation of Pseudomonas aeruginosa in intensive care units, the liquid hand soap was found to be highly contaminated (up to 8 × 10(5)cfu/g) with this pathogen. It had been used over the previous five months and was probably contaminated during manufacturing. To evaluate the burden of this contamination on patients by conducting an epidemiological investigation using molecular typing combined with whole genome sequencing (WGS). P. aeruginosa isolates from clinical specimens were analysed by double locus sequence typing (DLST) and compared with isolates recovered from the soap. Medical charts of patients infected with a genotype identical to those found in the soap were reviewed. WGS was performed on soap and patient isolates sharing the same genotype. P. aeruginosa isolates (N = 776) were available in 358/382 patients (93.7%). Only three patients (0.8%) were infected with a genotype found in the soap. Epidemiological investigations showed that the first patient was not exposed to the soap, the second could have been exposed, and the third was indeed exposed. WGS showed a high number of core single nucleotide polymorphism differences between patients and soap isolates. No close genetic association was observed between soap and patient isolates, ruling out the hypothesis of transmission. Despite a highly contaminated soap, the combined investigation with DLST and WGS ruled out any impact on patients. Hand hygiene performed with alcohol-based solution for >15 years was probably the main reason. However, such contamination represents a putative reservoir of pathogens that should be avoided in the hospital setting. Copyright © 2016 The Healthcare Infection Society. Published by Elsevier Ltd. All rights reserved.

Popular soap opera helps raise contraceptive use. Tanzania.

PubMed

1996-01-01

The latest Demographic and Health Surveys Report on Knowledge, Attitudes, and Practice documents an increase in the level of use of modern contraceptive methods in Tanzania between 1991 and 1994 from 5.9% to 11.3% of reproductive-age women. 53.2% of all women of reproductive age were exposed to mass media messages about family planning, which large majorities of men and women consider acceptable. 48.3% were exposed through radio, 22.9% reported listening to the US Agency for International Development-funded family planning promotional radio soap opera "Zinduka]", 22.5% read newspaper items, 17.5% saw posters, and 7.3% saw leaflets. 4.5% were visited by a family planning worker, 24.7% discussed family planning with a friend or relative, and 24.7% discussed family planning with health facility personnel. Zinduka], a popular 52-episode soap opera, depicts how the lives of Bomu wa Kabuma's family, in Msongano Town and Tawanya village in Tanzania, are affected because he is unable to provide for his eight children, parents, wife, mistress, and the mistress's child. The soap was produced with technical assistance from the Johns Hopkins University Center for Communication Programs Population Communication Services project. The 15-minute episodes were first broadcast in Swahili on Radio Tanzania from October 1993 through October 1994. The series was then resumed in September 1995 for another 12 months.

Electrochemistry at a Metal Nanoparticle on a Tunneling Film: A Steady-State Model of Current Densities at a Tunneling Ultramicroelectrode.

PubMed

Hill, Caleb M; Kim, Jiyeon; Bard, Allen J

2015-09-09

Here, a new methodology is proposed for treating electrochemical current densities in metal-insulator-metal nanoparticle (M-I-MNP) systems. The described model provides broad, practical insights about MNP-mediated electron transfer to redox species in solution, where electron transfer from the underlying electrode to a MNP via tunneling and heterogeneous electron transfer from the MNP to redox species in solution are treated as sequential steps. Tunneling is treated through an adaptation of the Simmons model of tunneling in metal-insulator-metal structures, and explicit equations are provided for tunneling currents, which demonstrate the effect of various experimental parameters, such as insulator thickness and MNP size. Overall, a general approach is demonstrated for determining experimental conditions where tunneling will have a measurable impact on the electrochemistry of M-I-MNP systems.

Chemical nature of the barrier in Pb/YBa2Cu3O(7-x) tunneling structures

NASA Technical Reports Server (NTRS)

Vasquez, R. P.; Foote, M. C.; Hunt, B. D.; Bajuk, L.

1991-01-01

Several reports of reproducible tunneling measurements on YBa2Cu3O(7-x) thin films or single crystals with a Pb counterelectrode have recently appeared. The nature of the tunnel barrier, formed by air exposure, in these structures has been unknown. In the present work, the chemical nature of the tunnel barrier is studied with X-ray photoelectron spectroscopy (XPS). Laser-ablated films grown on LaAlO3 which have been chemically etched and heated in air are found to form nonsuperconducting surface Ba species, evident in an increase of the high binding energy Ba 3d and O 1s signals. A deposited Pb film about 10 A thick is found to be oxidized, and Cu(+2) is partially reduced to Cu(+1). The tunneling barrier thus appears to consist of species resulting from a combination of the air exposure and a reaction between the superconductor and the deposited Pb counterelectrode.

Columnar to Nematic Mesophase Transition: Binary Mixtures of Copper Soaps with Hydrocarbons

NASA Astrophysics Data System (ADS)

Seghrouchni, R.; Skoulios, A.

1995-09-01

Copper (II) soaps are known to produce columnar mesophases at high temperatures. The polar groups of the soap molecules are stacked over one another within columns surrounded by the paraffin chains in a disordered conformation and laterally arranged according to a two-dimensional hexagonal lattice. Upon addition of a hydrocarbon, the mesophases swell homogeneously. The hydrocarbon molecules locate themselves among the disordered chains of the soap molecules, the columnar cores remain perfectly unchanged, keeping a constant intra-columnar stacking period, and the hexagonal lattice expands in proportion to the amount of hydrocarbon added to the system. Beyond a certain degree of swelling, the columnar mesophases suddenly turn into a nematic mesophase through a first-order phase transition. The structural elements that align parallel to the nematic director are the very same molecular columns that are involved in the columnar mesophases. The columnar to nematic mesophase transition was studied systematically as a function of the molecular size of the soaps and hydrocarbons used as diluents and discussed on a molecular level, emphasizing such aspects as the persistence length of the paraffin chains and the location of the solvent molecules among the columns.

Tunneling-Electron-Induced Light Emission from Single Gold Nanoclusters.

PubMed

Yu, Arthur; Li, Shaowei; Czap, Gregory; Ho, W

2016-09-14

The coupling of tunneling electrons with the tip-nanocluster-substrate junction plasmon was investigated by monitoring light emission in a scanning tunneling microscope (STM). Gold atoms were evaporated onto the ∼5 Å thick Al2O3 thin film grown on the NiAl (110) surface where they formed nanoclusters 3-7 nm wide. Scanning tunneling spectroscopy (STS) of these nanoclusters revealed quantum-confined electronic states. Spatially resolved photon imaging showed localized emission hot spots. Size dependent study and light emission from nanocluster dimers further support the viewpoint that coupling of tunneling electrons to the junction plasmon is the main radiative mechanism. These results showed the potential of the STM to reveal the electronic and optical properties of nanoscale metallic systems in the confined geometry of the tunnel junction.

Excitation of propagating surface plasmons with a scanning tunnelling microscope.

PubMed

Wang, T; Boer-Duchemin, E; Zhang, Y; Comtet, G; Dujardin, G

2011-04-29

Inelastic electron tunnelling excitation of propagating surface plasmon polaritons (SPPs) on a thin gold film is demonstrated. This is done by combining a scanning tunnelling microscope (STM) with an inverted optical microscope. Analysis of the leakage radiation in both the image and Fourier planes unambiguously shows that the majority (up to 99.5%) of the detected photons originate from propagating SPPs with propagation lengths of the order of 10  µm. The remaining photon emission is localized under the STM tip and is attributed to a tip-gold film coupled plasmon resonance as evidenced by the bimodal spectral distribution and enhanced emission intensity observed using a silver STM tip for excitation.

Numerical study of soap-film flow by nonuniform alternating electric fields

NASA Astrophysics Data System (ADS)

Nasiri, M.; Shirsavar, R.; Mollaei, S.; Ramos, A.

2017-02-01

Fluid flow of suspended liquid films induced by non-uniform alternating electric fields has been reported. The electric fields were generated by two rod-like electrodes perpendicular to the fluid surface. The observed fluid flow was explained qualitatively by considering a charge induction mechanism, where the electric field actuates on the charge induced on the film surface. In this paper we perform a numerical study of this fluid flow taking into account the charge induction mechanism. The numerical results are compared with experiments and good agreement is found. Finally, we propose the application of the device as a new kind of two dimensional fluid pump.

Numerical study of soap-film flow by nonuniform alternating electric fields.

PubMed

Nasiri, M; Shirsavar, R; Mollaei, S; Ramos, A

2017-02-01

Fluid flow of suspended liquid films induced by non-uniform alternating electric fields has been reported. The electric fields were generated by two rod-like electrodes perpendicular to the fluid surface. The observed fluid flow was explained qualitatively by considering a charge induction mechanism, where the electric field actuates on the charge induced on the film surface. In this paper we perform a numerical study of this fluid flow taking into account the charge induction mechanism. The numerical results are compared with experiments and good agreement is found. Finally, we propose the application of the device as a new kind of two dimensional fluid pump.

Effects of an entertainment-education radio soap opera on family planning behavior in Tanzania.

PubMed

Rogers, E M; Vaughan, P W; Swalehe, R M; Rao, N; Svenkerud, P; Sood, S

1999-09-01

An entertainment-education radio soap opera introduced in Tanzania in 1993 was evaluated by means of a field experimental design in which the radio program was broadcast by seven mainland stations of Radio Tanzania. An eighth station broadcast alternative programming from 1993 to 1995, its listenership serving as a comparison area in which contemporaneous changes in family planning adoption were measured. The soap opera was subsequently broadcast nationwide from 1995 to 1997. Data about the effects of the radio soap opera were gathered in five annual surveys of about 2,750 households in the comparison and the treatment areas and from a sample of new family planning adopters in 79 health clinics. The soap opera had strong behavioral effects on family planning adoption; it increased listeners' self-efficacy regarding family planning adoption and influenced listeners to talk with their spouses and peers about contraception.

Use of 3D Printing for Custom Wind Tunnel Fabrication

NASA Astrophysics Data System (ADS)

Gagorik, Paul; Bates, Zachary; Issakhanian, Emin

2016-11-01

Small-scale wind tunnels for the most part are fairly simple to produce with standard building equipment. However, the intricate bell housing and inlet shape of an Eiffel type wind tunnel, as well as the transition from diffuser to fan in a rectangular tunnel can present design and construction obstacles. With the help of 3D printing, these shapes can be custom designed in CAD models and printed in the lab at very low cost. The undergraduate team at Loyola Marymount University has built a custom benchtop tunnel for gas turbine film cooling experiments. 3D printing is combined with conventional construction methods to build the tunnel. 3D printing is also used to build the custom tunnel floor and interchangeable experimental pieces for various experimental shapes. This simple and low-cost tunnel is a custom solution for specific engineering experiments for gas turbine technology research.

There's alcohol in my soap: portrayal and effects of alcohol use in a popular television series.

PubMed

van Hoof, Joris J; de Jong, Menno D T; Fennis, Bob M; Gosselt, Jordy F

2009-06-01

Two studies are reported addressing the media influences on adolescents' alcohol-related attitudes and behaviours. A content analysis was conducted to investigate the prevalence of alcohol portrayal in a Dutch soap series. The coding scheme covered the alcohol consumption per soap character, drinking situations and drinking times. Inter-coder reliability was satisfactory. The results showed that alcohol portrayal was prominent and that many instances of alcohol use reflected undesirable behaviours. To assess the influence of such alcohol cues on adolescents, a 2x2 experiment was conducted focusing on the separate and combined effects of alcohol portrayal in the soap series and surrounding alcohol commercials. Whereas the alcohol commercials had the expected effects on adolescents' attitudes, the alcohol-related soap content only appeared to have unexpected effects. Adolescents who were exposed to the alcohol portrayal in the soap series had a less positive attitude towards alcohol and lower drinking intentions. Implications of these findings for health policy and future research are discussed.

Spatially-resolved magnetic resonance study of the dissolution interface between soaps and water

NASA Astrophysics Data System (ADS)

Ciampi, E.; Goerke, U.; McDonald, P. J.; Chambers, J. G.; Newling, B.

2002-06-01

The developing interfacial region between a soap bar and water has been studied using a suite of spatially resolved NMR techniques. Stray field imaging (STRAFI) allowed the dynamics of water ingress into a shop-bought, commercial soap to be followed. A simplistic analysis of the data shows the ingress to be a Fickian process (∝t1/2) in the first 4 h. The T2 contrast employed in the STRAFI method is not sufficient to resolve detail of the mesophase formation at the interface. However, double quantum filtered 2H spectroscopy at different positions in the interfacial region allowed water concentration (and mesophase distribution) to be mapped over the first 120 h of dissolution. A simple model shows good agreement with the water concentration data. In the isotropic soap solution above the interfacial region, J-cyclic cross polarization was used to selectively interrogate the CH2 1H of the soap alkyl chains and, in combination with a pulsed field gradient measurement of self-diffusion, suggests a micellar solution in which the hydrodynamic radius of the micelles is ~5nm.

Flow visualization of discrete hole film cooling for gas turbine applications

NASA Technical Reports Server (NTRS)

Colladay, R. S.; Russell, L. M.

1975-01-01

Film injection from discrete holes in a three row staggered array with 5-diameter spacing is studied. The boundary layer thickness-to-hole diameter ratio and Reynolds number are typical of gas turbine film cooling applications. Two different injection locations are studied to evaluate the effect of boundary layer thickness on film penetration and mixing. Detailed streaklines showing the turbulent motion of the injected air are obtained by photographing neutrally buoyant helium filled soap bubbles which follow the flow field. The bubble streaklines passing downstream injection locations are clearly identifiable and can be traced back to their origin. Visualization of surface temperature patterns obtained from infrared photographs of a similar film cooled surface are also included.

A pilot study on the evaluation of medical student documentation: assessment of SOAP notes.

PubMed

Seo, Ji-Hyun; Kong, Hyun-Hee; Im, Sun-Ju; Roh, HyeRin; Kim, Do-Kyong; Bae, Hwa-Ok; Oh, Young-Rim

2016-06-01

The purpose of this study was evaluation of the current status of medical students' documentation of patient medical records. We checked the completeness, appropriateness, and accuracy of 95 Subjective-Objective-Assessment-Plan (SOAP) notes documented by third-year medical students who participated in clinical skill tests on December 1, 2014. Students were required to complete the SOAP note within 15 minutes of an standard patient (SP)-encounter with a SP complaining rhinorrhea and warring about meningitis. Of the 95 SOAP notes reviewed, 36.8% were not signed. Only 27.4% documented the patient's symptoms under the Objective component, although all students completed the Subjective notes appropriately. A possible diagnosis was assessed by 94.7% students. Plans were described in 94.7% of the SOAP notes. Over half the students planned workups (56.7%) for diagnosis and treatment (52.6%). Accurate documentation of the symptoms, physical findings, diagnoses, and plans were provided in 78.9%, 9.5%, 62.1%, and 38.0% notes, respectively. Our results showed that third-year medical students' SOAP notes were not complete, appropriate, or accurate. The most significant problems with completeness were the omission of students' signatures, and inappropriate documentation of the physical examinations conducted. An education and assessment program for complete and accurate medical recording has to be developed.

The production of paper soaps from coconut oil and Virgin Coconut Oil (VCO) with the addition of glycerine as plasticizer

NASA Astrophysics Data System (ADS)

Widyasanti, Asri; Miracle Lenyta Ginting, Anastasia; Asyifani, Elgina; Nurjanah, Sarifah

2018-03-01

Hand washing with soap is important because it is proven to clean hands from germs and bacteria. The paper soapswere made from coconut oil and virgin coconut oil (VCO) with the addition of glycerin as a plasticizer. The aims of this research were to determine both formulation of paper soap using coconut oil and VCO based with addition of glycerin, and to determine the quality of the paper soapswhich is a disposable hand soap. This research used laboratory experimental method using descriptive analysis. The treatments of this research were treatment A (paper soap without the addition of glycerin), treatment B (paper soap with the addition of glycerin 10% (w/w)), treatment C (paper soap with the addition of glycerin 15% (w/w)), treatment D (paper soap with the addition of glycerin of 20% (w/w)). Parameters tested were moisture content, stability of foam, pH value, insoluble material in ethanol, free alkali content, unsaponified fat, antibacterial activity test, and organoleptic test. The result of physicochemical characteristics for bothcoconut oil-paper soap and VCO-paper soap revealed that treatment C (the addition of glycerin 15% (w/w) was the best soap formulation. Coconut Oil papersoap 15% w/w glicerin had water content 13.72%, the content of insoluble material in ethanol 3.93%, the content of free alkali 0.21%, and the content of unsaponified fat 4.06%, pH value 10.78, stability of foam 97.77%, and antibacterial activity against S. aureus 11.66 mm. Meanwhile, VCO paper soap 15% w/w glicerin had the value of water content of 18.47%, the value stability of foam of 96.7%, the pH value of 10.03, the value of insoluble material in ethanol of 3.49%, the value of free alkali content 0.17%, the value of unsaponified fat 4.91%, and the value of inhibition diameter on the antibacterial activity test 15.28 mm. Based on Mandatory Indonesian National Standard of solid soap SNI 3532:2016 showed that both of paper soap had not been accorded with SNI 3532:2016, unless the

The use of D-optimal mixture design in optimising okara soap formulation for stratum corneum application.

PubMed

Borhan, Farrah Payyadhah; Abd Gani, Siti Salwa; Shamsuddin, Rosnah

2014-01-01

Okara, soybean waste from tofu and soymilk production, was utilised as a natural antioxidant in soap formulation for stratum corneum application. D-optimal mixture design was employed to investigate the influence of the main compositions of okara soap containing different fatty acid and oils (virgin coconut oil A (24-28% w/w), olive oil B (15-20% w/w), palm oil C (6-10% w/w), castor oil D (15-20% w/w), cocoa butter E (6-10% w/w), and okara F (2-7% w/w)) by saponification process on the response hardness of the soap. The experimental data were utilized to carry out analysis of variance (ANOVA) and to develop a polynomial regression model for okara soap hardness in terms of the six design factors considered in this study. Results revealed that the best mixture was the formulation that included 26.537% A, 19.999% B, 9.998% C, 16.241% D, 7.633% E, and 7.000% F. The results proved that the difference in the level of fatty acid and oils in the formulation significantly affects the hardness of soap. Depending on the desirable level of those six variables, creation of okara based soap with desirable properties better than those of commercial ones is possible.

Ethical Gifts?: An Analysis of Soap-for-data Transactions in Malawian Survey Research Worlds.

PubMed

Biruk, Crystal

2017-09-01

In 2008, thousands of Malawians received soap from an American research project as a gift for survey participation. Soap was deemed an ethical, non-coercive gift by researchers and ethics boards, but took on meanings that expressed recipients' grievances and aspirations. Research participants reframed soap and research benefits as "rights" they are entitled to, wages for "work," and a symbol of exploitation. Enlisting the perspectives of Malawi's ethics board, demographers, Malawian fieldworkers, and research participants, I describe how soap is spoken about and operates in research worlds. I suggest that neither a prescriptive nor a situated frame for ethics-with their investments in standardization and attention to context, respectively-provides answers about how to compensate Malawian research participants. The conclusion gestures toward a reparative framework for thinking ethics that is responsive not just to project-based parameters but also to the histories and political economy in which projects (and ethics) are situated. © 2017 by the American Anthropological Association.

Lipase pre-hydrolysis enhance anaerobic biodigestion of soap stock from an oil refining industry.

PubMed

Cherif, Slim; Aloui, Fathi; Carrière, Frédéric; Sayadi, Sami

2014-01-01

A novel alcalophilic Staphylococcus haemolyticus strain with the lipolytic activity was used to perform enzymatic hydrolysis pretreatment of soap stock: a lipid rich solid waste from an oil refining industry. The culture liquid of the selected bacteria and an enzymatic preparation obtained by precipitation with ammonium sulphate from a filtrate of the same culture liquid were used for enzymatic pretreatment. The hydrolysis was carried with different incubation concentrations (10, 20 and 30%) of soap stock and the pretreatment efficiency was verified by running comparative biodegradability tests (crude and treated lipid waste). All pretreated assays showed higher reaction rate compared to crude lipid waste, which was confirmed by the increased levels of biogas production. The pretreatment of solutions containing 10% emulsified soap stock was optimized for 24 h hydrolysis time, enabling high-biogaz formation (800 ml). The use of enzymatic pre-treatment seemed to be a very promising alternative for treating soap stock having high fat contents.

Reflection-Type Oil-Film Skin-Friction Meter

NASA Technical Reports Server (NTRS)

Bandyopadhyay, Promode R.; Weinstein, Leonard M.

1993-01-01

Oil-film skin-friction meter for both flight and wind-tunnel applications uses internal reflection and is self-contained, compact unit. Contained in palm-sized housing, in which source of light, mirrors, and sensor mounted rigidly in alignment. Entire unit mounted rigidly under skin of aircraft or wind tunnel, eliminating any relative vibration between optical elements and skin of aircraft or wind tunnel. Meter primarily applicable to flight and wind-tunnel tests, also used in chemical-processing plants.

An electron tunneling study of superconductivity in amorphous Sn(sub 1-x)Cu(sub x) thin films

NASA Technical Reports Server (NTRS)

Naugle, D. G.; Watson, P. W., III; Rathnayaka, K. D. D.

1995-01-01

The amorphous phase of Sn would have a superconducting transition temperature near 8 K, much higher than that of crystalline Sn with T(sub c) = 3.5 K. To obtain the amorphous phase, however, it is necessary to use a Sn alloy, usually Cu, and quench condense the alloy films onto a liquid He temperature substrate. Alloying with Cu reduces the superconducting transition temperature almost linearly with Cu concentration with an extrapolation of T(sub c) to zero for x = 0.85. Analysis of the tunneling characteristics between a normal metal electrode with an insulating barrier and superconducting amorphous Sn-Cu films provides detailed information on the changes in the electron-phonon coupling which determines T(sub c) in these alloys. The change from very strong electron-phonon coupling to weak-coupling with the increase in Cu content of amorphous Sn-Cu alloys for the range 0.08 is less than or equal to x is less than or equal to 0.41 is presented and discussed in terms of theories of electron-phonon coupling in disordered metals.

Highly reliable top-gated thin-film transistor memory with semiconducting, tunneling, charge-trapping, and blocking layers all of flexible polymers.

PubMed

Wang, Wei; Hwang, Sun Kak; Kim, Kang Lib; Lee, Ju Han; Cho, Suk Man; Park, Cheolmin

2015-05-27

The core components of a floating-gate organic thin-film transistor nonvolatile memory (OTFT-NVM) include the semiconducting channel layer, tunneling layer, floating-gate layer, and blocking layer, besides three terminal electrodes. In this study, we demonstrated OTFT-NVMs with all four constituent layers made of polymers based on consecutive spin-coating. Ambipolar charges injected and trapped in a polymer electret charge-controlling layer upon gate program and erase field successfully allowed for reliable bistable channel current levels at zero gate voltage. We have observed that the memory performance, in particular the reliability of a device, significantly depends upon the thickness of both blocking and tunneling layers, and with an optimized layer thickness and materials selection, our device exhibits a memory window of 15.4 V, on/off current ratio of 2 × 10(4), read and write endurance cycles over 100, and time-dependent data retention of 10(8) s, even when fabricated on a mechanically flexible plastic substrate.

Assessment of SOAP note evaluation tools in colleges and schools of pharmacy.

PubMed

Sando, Karen R; Skoy, Elizabeth; Bradley, Courtney; Frenzel, Jeanne; Kirwin, Jennifer; Urteaga, Elizabeth

2017-07-01

To describe current methods used to assess SOAP notes in colleges and schools of pharmacy. Members of the American Association of Colleges of Pharmacy Laboratory Instructors Special Interest Group were invited to share assessment tools for SOAP notes. Content of submissions was evaluated to characterize overall qualities and how the tools assessed subjective, objective, assessment, and plan information. Thirty-nine assessment tools from 25 schools were evaluated. Twenty-nine (74%) of the tools were rubrics and ten (26%) were checklists. All rubrics included analytic scoring elements, while two (7%) were mixed with holistic and analytic scoring elements. A majority of the rubrics (35%) used a four-item rating scale. Substantial variability existed in how tools evaluated subjective and objective sections. All tools included problem identification in the assessment section. Other assessment items included goals (82%) and rationale (69%). Seventy-seven percent assessed drug therapy; however, only 33% assessed non-drug therapy. Other plan items included education (59%) and follow-up (90%). There is a great deal of variation in the specific elements used to evaluate SOAP notes in colleges and schools of pharmacy. Improved consistency in assessment methods to evaluate SOAP notes may better prepare students to produce standardized documentation when entering practice. Copyright © 2017 Elsevier Inc. All rights reserved.

40 CFR 467.60 - Applicability; description of the drawing with emulsions or soaps subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Applicability; description of the drawing with emulsions or soaps subcategory. 467.60 Section 467.60 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ALUMINUM FORMING POINT SOURCE CATEGORY Drawing With Emulsions or Soaps Subcategory...

40 CFR 467.60 - Applicability; description of the drawing with emulsions or soaps subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 30 2011-07-01 2011-07-01 false Applicability; description of the drawing with emulsions or soaps subcategory. 467.60 Section 467.60 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ALUMINUM FORMING POINT SOURCE CATEGORY Drawing With Emulsions or Soaps Subcategory...

Characterization of 10,12-pentacosadiynoic acid Langmuir-Blodgett monolayers and their use in metal-insulator-metal tunnel devices.

PubMed

Sharma, Saumya; Khawaja, Mohamad; Ram, Manoj K; Goswami, D Yogi; Stefanakos, Elias

2014-01-01

The characterization of Langmuir-Blodgett thin films of 10,12-pentacosadiynoic acid (PDA) and their use in metal-insulator-metal (MIM) devices were studied. The Langmuir monolayer behavior of the PDA film was studied at the air/water interface using surface tension-area isotherms of polymeric and monomeric PDA. Langmuir-Blodgett (LB, vertical deposition) and Langmuir-Schaefer (LS, horizontal deposition) techniques were used to deposit the PDA film on various substrates (glass, quartz, silicon, and nickel-coated film on glass). The electrochemical, electrical and optical properties of the LB and LS PDA films were studied using cyclic voltammetry, current-voltage characteristics (I-V), and UV-vis and FTIR spectroscopies. Atomic force microscopy measurements were performed in order to analyze the surface morphology and roughness of the films. A MIM tunnel diode was fabricated using a PDA monolayer assembly as the insulating barrier, which was sandwiched between two nickel layers. The precise control of the thickness of the insulating monolayers proved critical for electron tunneling to take place in the MIM structure. The current-voltage characteristics of the MIM diode revealed tunneling behavior in the fabricated Ni-PDA LB film-Ni structures.

Dual metal gate tunneling field effect transistors based on MOSFETs: A 2-D analytical approach

NASA Astrophysics Data System (ADS)

Ramezani, Zeinab; Orouji, Ali A.

2018-01-01

A novel 2-D analytical drain current model of novel Dual Metal Gate Tunnel Field Effect Transistors Based on MOSFETs (DMG-TFET) is presented in this paper. The proposed Tunneling FET is extracted from a MOSFET structure by employing an additional electrode in the source region with an appropriate work function to induce holes in the N+ source region and hence makes it as a P+ source region. The electric field is derived which is utilized to extract the expression of the drain current by analytically integrating the band to band tunneling generation rate in the tunneling region based on the potential profile by solving the Poisson's equation. Through this model, the effects of the thin film thickness and gate voltage on the potential, the electric field, and the effects of the thin film thickness on the tunneling current can be studied. To validate our present model we use SILVACO ATLAS device simulator and the analytical results have been compared with it and found a good agreement.

Statics and dynamics of adhesion between two soap bubbles.

PubMed

Besson, S; Debrégeas, G

2007-10-01

An original set-up is used to study the adhesive properties of two hemispherical soap bubbles put into contact. The contact angle at the line connecting the three films is extracted by image analysis of the bubbles profiles. After the initial contact, the angle rapidly reaches a static value slightly larger than the standard 120 degrees angle expected from Plateau rule. This deviation is consistent with previous experimental and theoretical studies: it can be quantitatively predicted by taking into account the finite size of the Plateau border (the liquid volume trapped at the vertex) in the free energy minimization. The visco-elastic adhesion properties of the bubbles are further explored by measuring the deviation Delta theta (d)(t) of the contact angle from the static value as the distance between the two bubbles supports is sinusoidally modulated. It is found to linearly increase with Delta r(c) / r(c) , where r(c) is the radius of the central film and Delta r(c) the amplitude of modulation of this length induced by the displacement of the supports. The in-phase and out-of-phase components of Delta theta (d)(t) with the imposed modulation frequency are systematically probed, which reveals a transition from a viscous to an elastic response of the system with a crossover pulsation of the order 1rad x s(-1). Independent interfacial rheological measurements, obtained from an oscillating bubble experiment, allow us to develop a model of dynamic adhesion which is confronted to our experimental results. The relevance of such adhesive dynamic properties to the rheology of foams is briefly discussed using a perturbative approach to the Princen 2D model of foams.

A Discovery Experiment: Carbon Dioxide Soap Bubble Dynamics.

ERIC Educational Resources Information Center

Millikan, Roger C.

1978-01-01

The observation of soap bubbles in a beaker of carbon dioxide gas helps students to feel the pleasure that comes from understanding nature, from applying that understanding to real problems, and from making unexpected discoveries that yield to analysis. (Author/BB)

Chain polymerization of diacetylene compound multilayer films on the topmost surface initiated by a scanning tunneling microscope tip.

PubMed

Takajo, Daisuke; Okawa, Yuji; Hasegawa, Tsuyoshi; Aono, Masakazu

2007-05-08

Chain polymerizations of diacetylene compound multilayer films on graphite substrates were examined with a scanning tunneling microscope (STM) at the liquid/solid interface of the phenyloctane solution. The first layer grew very quickly into many small domains. This was followed by the slow formation of the piled up layers into much larger domains. Chain polymerization on the topmost surface layer could be initiated by applying a pulsed voltage between the STM tip and the substrate, usually producing a long polymer of submicrometer length. In contrast, polymerizations on the underlying layer were never observed. This can be explained by a conformation model in which the polymer backbone is lifted up.

The Use of D-Optimal Mixture Design in Optimising Okara Soap Formulation for Stratum Corneum Application

PubMed Central

Borhan, Farrah Payyadhah; Abd Gani, Siti Salwa; Shamsuddin, Rosnah

2014-01-01

Okara, soybean waste from tofu and soymilk production, was utilised as a natural antioxidant in soap formulation for stratum corneum application. D-optimal mixture design was employed to investigate the influence of the main compositions of okara soap containing different fatty acid and oils (virgin coconut oil A (24–28% w/w), olive oil B (15–20% w/w), palm oil C (6–10% w/w), castor oil D (15–20% w/w), cocoa butter E (6–10% w/w), and okara F (2–7% w/w)) by saponification process on the response hardness of the soap. The experimental data were utilized to carry out analysis of variance (ANOVA) and to develop a polynomial regression model for okara soap hardness in terms of the six design factors considered in this study. Results revealed that the best mixture was the formulation that included 26.537% A, 19.999% B, 9.998% C, 16.241% D, 7.633% E, and 7.000% F. The results proved that the difference in the level of fatty acid and oils in the formulation significantly affects the hardness of soap. Depending on the desirable level of those six variables, creation of okara based soap with desirable properties better than those of commercial ones is possible. PMID:25548777

40 CFR 417.30 - Applicability; description of the soap manufacturing by fatty acid neutralization subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... manufacturing by fatty acid neutralization subcategory. 417.30 Section 417.30 Protection of Environment... POINT SOURCE CATEGORY Soap Manufacturing by Fatty Acid Neutralization Subcategory § 417.30 Applicability; description of the soap manufacturing by fatty acid neutralization subcategory. The provisions of this subpart...

Contamination of liquid soap for hospital use with Raoultella planticola.

PubMed

García-San Miguel, L; Sáez-Nieto, J A; Medina, M J; López Hernández, S; Sánchez-Romero, I; Ganga, B; Asensio, Á

2014-03-01

This article reports the contamination of a batch of liquid soap for hospital use with Raoultella planticola. The micro-organism was first identified as Klebsiella pneumoniae due to the inability of automated systems to characterize this species. There is a need to strengthen the inspection of cosmetic products to be used in the hospital setting. It is recommended that hospitalized patients at the highest risk of infection should use antimicrobial soaps for personal hygiene. The incidence of infections due to R. planticola is unknown as it is usually misclassified as Klebsiella spp. by automated systems. Copyright © 2014 The Healthcare Infection Society. Published by Elsevier Ltd. All rights reserved.

Effects of polyalkylene glycols and fatty acid soaps on properties of synthetic lubricating-cooling fluids

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stulii, A.A.

1983-01-01

The lack of any effect of the polyalkylene glycols on the series of properties of the fatty acid soaps was confirmed by replacing the PEG-35 in the synthetic lubricating-cooling fluid (LCF) by a polyethylene glycol with a molecular weight of 400 or 6000, a propylene oxide oligomer with a molecular weight of 700, or a copolymer of ethylene and propylene oxides (Pluronic 44, Pluriol PE-6400, Hydropol 200). Attempts to select surfactants and optimal concentrations in synthetic LCFs based on polyalkylene glycols. Indicates that of the studied soaps, those of the most interest are the triethanolamine soaps of individual C/sub 6/-C/submore » 10/ fatty acids and commercial mixed C/sub 7/-C/sub 9/ synthetic fatty acids. Finds that the polyalkylene glycols and the indicated soaps supplement each other, imparting the required set of properties to the LCF.« less

Simulated Thin-Film Growth and Imaging

NASA Astrophysics Data System (ADS)

Schillaci, Michael

2001-06-01

Thin-films have become the cornerstone of the electronics, telecommunications, and broadband markets. A list of potential products includes: computer boards and chips, satellites, cell phones, fuel cells, superconductors, flat panel displays, optical waveguides, building and automotive windows, food and beverage plastic containers, metal foils, pipe plating, vision ware, manufacturing equipment and turbine engines. For all of these reasons a basic understanding of the physical processes involved in both growing and imaging thin-films can provide a wonderful research project for advanced undergraduate and first-year graduate students. After producing rudimentary two- and three-dimensional thin-film models incorporating ballsitic deposition and nearest neighbor Coulomb-type interactions, the QM tunneling equations are used to produce simulated scanning tunneling microscope (SSTM) images of the films. A discussion of computational platforms, languages, and software packages that may be used to accomplish similar results is also given.

Performance of lead-free versus lead-based hunting ammunition in ballistic soap.

PubMed

Gremse, Felix; Krone, Oliver; Thamm, Mirko; Kiessling, Fabian; Tolba, René Hany; Rieger, Siegfried; Gremse, Carl

2014-01-01

Lead-free hunting bullets are an alternative to lead-containing bullets which cause health risks for humans and endangered scavenging raptors through lead ingestion. However, doubts concerning the effectiveness of lead-free hunting bullets hinder the wide-spread acceptance in the hunting and wildlife management community. We performed terminal ballistic experiments under standardized conditions with ballistic soap as surrogate for game animal tissue to characterize dimensionally stable, partially fragmenting, and deforming lead-free bullets and one commonly used lead-containing bullet. The permanent cavities created in soap blocks are used as a measure for the potential wound damage. The soap blocks were imaged using computed tomography to assess the volume and shape of the cavity and the number of fragments. Shots were performed at different impact speeds, covering a realistic shooting range. Using 3D image segmentation, cavity volume, metal fragment count, deflection angle, and depth of maximum damage were determined. Shots were repeated to investigate the reproducibility of ballistic soap experiments. All bullets showed an increasing cavity volume with increasing deposited energy. The dimensionally stable and fragmenting lead-free bullets achieved a constant conversion ratio while the deforming copper and lead-containing bullets showed a ratio, which increases linearly with the total deposited energy. The lead-containing bullet created hundreds of fragments and significantly more fragments than the lead-free bullets. The deflection angle was significantly higher for the dimensionally stable bullet due to its tumbling behavior and was similarly low for the other bullets. The deforming bullets achieved higher reproducibility than the fragmenting and dimensionally stable bullets. The deforming lead-free bullet closely resembled the deforming lead-containing bullet in terms of energy conversion, deflection angle, cavity shape, and reproducibility, showing that

Foam flow and liquid films motion: role of the surfactants properties

NASA Astrophysics Data System (ADS)

Cantat, Isabelle

2011-11-01

Liquid foams absorb energy in a much more efficient way than each of its constituents, taken separately. However, the local process at the origin of the energy dissipation is not entirely elucidated yet, and several models may apply, thus making worth local studies on simpler systems. We investigate the motion through a wet tube of transverse soap films, or lamellae, combining local thickness and velocity measurements in the wetting film. For foaming solution with a high dilatational surface modulus, we reveal a zone of several centimeters in length, the dynamic wetting film, which is significantly influenced by a moving lamella. The dependence of this influence length on lamella velocity and wetting film thickness provides an accurate discrimination among several possible surfactants models. In collaboration with B. Dollet.

The long-term use of soap does not affect the pH-maintenance mechanism of human skin.

PubMed

Takagi, Y; Kaneda, K; Miyaki, M; Matsuo, K; Kawada, H; Hosokawa, H

2015-05-01

The pH at the surface of healthy human skin is around 5. Cleansing the skin with soap increases the pH of the skin, which then returns to a more acidic pH within a few hours. However, the effects of skin cleansing with soap over a long time on the pH regulatory system is still unclear. We compared the pH of the skin between users of a soap-based cleanser and of a mild-acidic cleanser prior to and following the cleansing. This study had two groups of subjects, one group who had used a soap-based cleanser for more than 5 years and the other group who had used a mild-acidic cleanser for more than 5 years. The pH on the inner forearm of each subject was measured prior to and for 6 h after cleansing with a soap bar. There were no differences between the pH of the skin these two groups prior to cleansing, immediately after cleansing or in the pH recovery rate for 6 h. These results suggest that long-term continuous use of a soap-based cleanser does not affect the pH-maintaining mechanism of human skin. © 2014 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Characterization of 10,12-pentacosadiynoic acid Langmuir–Blodgett monolayers and their use in metal–insulator–metal tunnel devices

PubMed Central

Sharma, Saumya; Khawaja, Mohamad; Ram, Manoj K; Goswami, D Yogi

2014-01-01

Summary The characterization of Langmuir–Blodgett thin films of 10,12-pentacosadiynoic acid (PDA) and their use in metal–insulator–metal (MIM) devices were studied. The Langmuir monolayer behavior of the PDA film was studied at the air/water interface using surface tension–area isotherms of polymeric and monomeric PDA. Langmuir–Blodgett (LB, vertical deposition) and Langmuir–Schaefer (LS, horizontal deposition) techniques were used to deposit the PDA film on various substrates (glass, quartz, silicon, and nickel-coated film on glass). The electrochemical, electrical and optical properties of the LB and LS PDA films were studied using cyclic voltammetry, current–voltage characteristics (I–V), and UV–vis and FTIR spectroscopies. Atomic force microscopy measurements were performed in order to analyze the surface morphology and roughness of the films. A MIM tunnel diode was fabricated using a PDA monolayer assembly as the insulating barrier, which was sandwiched between two nickel layers. The precise control of the thickness of the insulating monolayers proved critical for electron tunneling to take place in the MIM structure. The current–voltage characteristics of the MIM diode revealed tunneling behavior in the fabricated Ni–PDA LB film–Ni structures. PMID:25551052

Effects of soap-water wash on human epidermal penetration.

PubMed

Zhu, Hanjiang; Jung, Eui-Chang; Phuong, Christina; Hui, Xiaoying; Maibach, Howard

2016-08-01

Skin decontamination is a primary interventional method used to decrease dermal absorption of hazardous contaminants, including chemical warfare agents, pesticides and industrial pollutants. Soap and water wash, the most common and readily available decontamination system, may enhance percutaneous absorption through the "wash-in effect." To understand better the effect of soap-water wash on percutaneous penetration, and provide insight to improving skin decontamination methods, in vitro human epidermal penetration rates of four C(14) -labeled model chemicals (hydroquinone, clonidine, benzoic acid and paraoxon) were assayed using flow-through diffusion cells. Stratum corneum (SC) absorption rates of these chemicals at various hydration levels (0-295% of the dry SC weights) were determined and compared with the results of the epidermal penetration study to clarify the effect of SC hydration on skin permeability. Results showed accelerated penetration curves of benzoic acid and paraoxon after surface wash at 30 min postdosing. Thirty minutes after washing (60 min postdosing), penetration rates of hydroquinone and benzoic acid decreased due to reduced amounts of chemical on the skin surface and in the SC. At the end of the experiment (90 min postdosing), a soap-water wash resulted in lower hydroquinone penetration, greater paraoxon penetration and similar levels of benzoic acid and clonidine penetration compared to penetration levels in the non-wash groups. The observed wash-in effect agrees with the enhancement effect of SC hydration on the SC chemical absorption rate. These results suggest SC hydration derived from surface wash to be one cause of the wash-in effect. Further, the occurrence of a wash-in effect is dependent on chemical identity and elapsed time between exposure and onset of decontamination. By reducing chemical residue quantity on skin surface and in the SC reservoir, the soap-water wash may decrease the total quantity of chemical absorbed in the

Isolation of Raoultella planticola from refillable antimicrobial liquid soap dispensers in a dental setting

PubMed Central

Tomlin, Nancy; Ruby, John D.

2014-01-01

Background Liquid antimicrobial soaps are commonly used in the dental healthcare setting for hand washing to minimize the potential spread of infectious agents to healthcare workers (HCW) and patients. The purpose of the current study was to evaluate possible bacterial contamination of antimicrobial liquid soap dispensers located in two institutional comprehensive dental care clinics. Methods Fourteen soap dispensers and original stock containers were sampled. A 1 ml aliquot was diluted in 10 ml of phosphate buffer (Tween 80). Serial dilutions were plated in duplicate on neutralizing agar and incubated for 7 days. Molecular identification was performed using 500 bp comparisons of 16S rDNA sequencing. Taq PCR was performed with sequence specific primers for Raoultella species. Results Bacterial growth was observed at 18 hours for 57% (8/14) of soap dispenser samples. Bacterial densities ranged from 4 ×102–6 ×109 CFU/mL. Original commercial containers exhibited no growth. Isolates were identified as Raoultella (Klebsiella) planticola. Conclusions This is the first study indicating recovery of R. planticola from antimicrobial liquid soap dispensers. R. planticola is a recognized environmental opportunistic pathogen that potentially poses a health concern. Practical Implications These findings indicate compliance problems with infection prevention recommendations and support the CDC’s recommendation that dispensers should not be “topped off”. High bacterial loads of R. planticola are inconsistent with infection control practices and are a concern since transmission and possible infection to the HCW or the patient may occur. PMID:25819655

Do Aloe vera and Ageratum conyzoides enhance the anti-microbial activity of traditional medicinal soft soaps (Osedudu)?

PubMed

Moody, J O; Adebiyi, O A; Adeniyi, B A

2004-05-01

The Nigerian traditional soft soaps prepared using varied locally sourced raw materials such as cocoa pod ash (Theobroma cacao) palm kernel shaft ash (Elaies guineensis) have been evaluated for their physico-chemical properties and anti-microbial activities using standard pharmacopoeia protocols and an in-vitro agar diffusion bioassay method. The anti-microbial evaluation was done with and without incorporation of Aloe vera and Ageratum conyzoides extractives into the soap samples. Results showed that the physico-chemical properties of the soaps are dependent on the raw materials utilised. The incorporated medicinal plants used in this study, however, did not show any significant effect on the anti-microbial activities exhibited by the various soaps against the bacterial and fungal test organisms. Copyright 2004 Elsevier Ireland Ltd.

Comparison of virucidal activity of alcohol-based hand sanitizers versus antimicrobial hand soaps in vitro and in vivo.

PubMed

Steinmann, J; Paulmann, D; Becker, B; Bischoff, B; Steinmann, E; Steinmann, J

2012-12-01

Three ethanol-based sanitizers were compared with three antimicrobial liquid soaps for their efficacy to inactivate polio-, adeno-, vaccinia- and bovine viral diarrhoea virus (BVDV) as well as feline calicivirus (FCV) and murine norovirus (MNV) as surrogates for human norovirus in a suspension test. Additionally, sanitizers and soaps were examined against MNV in a modified fingerpad method. All sanitizers sufficiently inactivated the test viruses in the suspension test whereas two soaps were active only against vaccinia virus and BVDV. In the modified fingerpad test a povidone-iodine-containing soap was superior to the sanitizers whereas the other two soaps showed no activity. Copyright © 2012 The Healthcare Infection Society. Published by Elsevier Ltd. All rights reserved.

Chemical Constituents and an Alternative Medicinal Veterinary Herbal Soap Made from Senna macranthera

PubMed Central

Inoue Andrade, Flávia; Purgato, Gislaine Aparecida; de Faria Maia, Thalita; Pais Siqueira, Raoni; Lima, Sâmia; Diaz, Marisa Alves Nogueira

2015-01-01

Upon undergoing biomonitoring, the most active dichloromethane extract retrieved from Senna macranthera roots led to the isolation of three main compounds: emodine, physione, and chrysophanol. In this sequence, these compounds revealed a potential antibacterial activity against Staphylococcus aureus strains isolated from animals with mastitis infections with minimum inhibitory concentration (MIC) values of 20, 90, and 90 μg mL−1, respectively. Therefore, an herbal soap was also produced from this same active extract. This soap was tested in vitro using gloves contaminated by animals with bovine mastitis that had been discarded after use by milkers and showed similar results to previously tested compounds. These results indicate the potential of this plant as an alternative veterinary medicine for the production of antibacterial soaps that aimed at controlling bovine mastitis infections in small Brazilian farms. PMID:25821480

Optimizing Libraries’ Content Findability Using Simple Object Access Protocol (SOAP) With Multi-Tier Architecture

NASA Astrophysics Data System (ADS)

Lahinta, A.; Haris, I.; Abdillah, T.

2017-03-01

The aim of this paper is to describe a developed application of Simple Object Access Protocol (SOAP) as a model for improving libraries’ digital content findability on the library web. The study applies XML text-based protocol tools in the collection of data about libraries’ visibility performance in the search results of the book. Model from the integrated Web Service Document Language (WSDL) and Universal Description, Discovery and Integration (UDDI) are applied to analyse SOAP as element within the system. The results showed that the developed application of SOAP with multi-tier architecture can help people simply access the website in the library server Gorontalo Province and support access to digital collections, subscription databases, and library catalogs in each library in Regency or City in Gorontalo Province.

Band-to-band tunneling in Γ valley for Ge source lateral tunnel field effect transistor: Thickness scaling

NASA Astrophysics Data System (ADS)

Jain, Prateek; Rastogi, Priyank; Yadav, Chandan; Agarwal, Amit; Chauhan, Yogesh Singh

2017-07-01

The direct and indirect valleys in Germanium (Ge) are separated by a very small offset, which opens up the prospect of direct tunneling in the Γ valley of an extended Ge source tunnel field effect transistor (TFET). We explore the impact of thickness scaling of extended Ge source lateral TFET on the band to band tunneling (BTBT) current. The Ge source is extended inside the gate by 2 nm to confine the tunneling in Ge only. We observe that as the thickness is scaled, the band alignment at the Si/Ge heterojunction changes significantly, which results in an increase in Ge to Si BTBT current. Based on density functional calculations, we first obtain the band structure parameters (bandgap, effective masses, etc.) for the Ge and Si slabs of varying thickness, and these are then used to obtain the thickness dependent Kane's BTBT tunneling parameters. We find that electrostatics improves as the thickness is reduced in the ultra-thin Ge film ( ≤ 10 nm). The ON current degrades as we scale down in thickness; however, the subthreshold slope ( S S AVG ) improves remarkably with thickness scaling due to subsurface BTBT. We predict that 8 nm thin devices offer the best option for optimized ON current and S S AVG .

Thickness scaling of atomic-layer-deposited HfO2 films and their application to wafer-scale graphene tunnelling transistors

PubMed Central

Jeong, Seong-Jun; Gu, Yeahyun; Heo, Jinseong; Yang, Jaehyun; Lee, Chang-Seok; Lee, Min-Hyun; Lee, Yunseong; Kim, Hyoungsub; Park, Seongjun; Hwang, Sungwoo

2016-01-01

The downscaling of the capacitance equivalent oxide thickness (CET) of a gate dielectric film with a high dielectric constant, such as atomic layer deposited (ALD) HfO2, is a fundamental challenge in achieving high-performance graphene-based transistors with a low gate leakage current. Here, we assess the application of various surface modification methods on monolayer graphene sheets grown by chemical vapour deposition to obtain a uniform and pinhole-free ALD HfO2 film with a substantially small CET at a wafer scale. The effects of various surface modifications, such as N-methyl-2-pyrrolidone treatment and introduction of sputtered ZnO and e-beam-evaporated Hf seed layers on monolayer graphene, and the subsequent HfO2 film formation under identical ALD process parameters were systematically evaluated. The nucleation layer provided by the Hf seed layer (which transforms to the HfO2 layer during ALD) resulted in the uniform and conformal deposition of the HfO2 film without damaging the graphene, which is suitable for downscaling the CET. After verifying the feasibility of scaling down the HfO2 thickness to achieve a CET of ~1.5 nm from an array of top-gated metal-oxide-graphene field-effect transistors, we fabricated graphene heterojunction tunnelling transistors with a record-low subthreshold swing value of <60 mV/dec on an 8″ glass wafer. PMID:26861833

A modular designed ultra-high-vacuum spin-polarized scanning tunneling microscope with controllable magnetic fields for investigating epitaxial thin films.

PubMed

Wang, Kangkang; Lin, Wenzhi; Chinchore, Abhijit V; Liu, Yinghao; Smith, Arthur R

2011-05-01

A room-temperature ultra-high-vacuum scanning tunneling microscope for in situ scanning freshly grown epitaxial films has been developed. The core unit of the microscope, which consists of critical components including scanner and approach motors, is modular designed. This enables easy adaptation of the same microscope units to new growth systems with different sample-transfer geometries. Furthermore the core unit is designed to be fully compatible with cryogenic temperatures and high magnetic field operations. A double-stage spring suspension system with eddy current damping has been implemented to achieve ≤5 pm z stability in a noisy environment and in the presence of an interconnected growth chamber. Both tips and samples can be quickly exchanged in situ; also a tunable external magnetic field can be introduced using a transferable permanent magnet shuttle. This allows spin-polarized tunneling with magnetically coated tips. The performance of this microscope is demonstrated by atomic-resolution imaging of surface reconstructions on wide band-gap GaN surfaces and spin-resolved experiments on antiferromagnetic Mn(3)N(2)(010) surfaces.

Metal-organic chemical vapor deposition of high quality, high indium composition N-polar InGaN layers for tunnel devices

NASA Astrophysics Data System (ADS)

Lund, Cory; Romanczyk, Brian; Catalano, Massimo; Wang, Qingxiao; Li, Wenjun; DiGiovanni, Domenic; Kim, Moon J.; Fay, Patrick; Nakamura, Shuji; DenBaars, Steven P.; Mishra, Umesh K.; Keller, Stacia

2017-05-01

In this study, the growth of high quality N-polar InGaN films by metalorganic chemical vapor deposition is presented with a focus on growth process optimization for high indium compositions and the structural and tunneling properties of such films. Uniform InGaN/GaN multiple quantum well stacks with indium compositions up to 0.46 were grown with local compositional analysis performed by energy-dispersive X-ray spectroscopy within a scanning transmission electron microscope. Bright room-temperature photoluminescence up to 600 nm was observed for films with indium compositions up to 0.35. To study the tunneling behavior of the InGaN layers, N-polar GaN/In0.35Ga0.65N/GaN tunnel diodes were fabricated which reached a maximum current density of 1.7 kA/cm2 at 5 V reverse bias. Temperature-dependent measurements are presented and confirm tunneling behavior under reverse bias.

Use of Electronic Loggers to Measure Changes in the Rates of Hand Washing with Soap in Low-Income Urban Households in India

PubMed Central

Wright, Richard L.; Zillmer, Ruediger; Biran, Adam; Hall, Peter; Sidibe, Myriam

2015-01-01

We evaluated the utility of electronic loggers to measure the effects of a simple intervention designed to influence the rates of hand washing with soap within enclosed toilets and bathrooms in low-income urban households in Kerala, India. 58 households were given three items with embedded electronic loggers for a period of 2-5 days. Two logged soaps tracked hand and body washing in the bathroom. The third logged item was a water vessel used for flushing the toilet and for post-defecation anal cleansing; this served as a marker of toilet use. In addition, 28 households in a Soap by toilet arm were given an additional logged soap, to be kept by the toilet, and used for hand washing. Compared with the Soap in bathroom arm, the loggers in the Soap by toilet households recorded 73% greater daily use of soaps designated for hand washing (t(36)=2.92, p<0.01) and 172% greater use within 2 minutes of the use of the water vessel (t(36)=3.51, p = 0.001). We conclude that the loggers were capable of detecting changes in the rates of hand washing with soap and changes in hand washing with soap after use of the toilet. Further adoption of logger technologies would enable more insightful studies of hand washing within urban environments. PMID:26101886

Use of Electronic Loggers to Measure Changes in the Rates of Hand Washing with Soap in Low-Income Urban Households in India.

PubMed

Wright, Richard L; Zillmer, Ruediger; Biran, Adam; Hall, Peter; Sidibe, Myriam

2015-01-01

We evaluated the utility of electronic loggers to measure the effects of a simple intervention designed to influence the rates of hand washing with soap within enclosed toilets and bathrooms in low-income urban households in Kerala, India. 58 households were given three items with embedded electronic loggers for a period of 2-5 days. Two logged soaps tracked hand and body washing in the bathroom. The third logged item was a water vessel used for flushing the toilet and for post-defecation anal cleansing; this served as a marker of toilet use. In addition, 28 households in a Soap by toilet arm were given an additional logged soap, to be kept by the toilet, and used for hand washing. Compared with the Soap in bathroom arm, the loggers in the Soap by toilet households recorded 73% greater daily use of soaps designated for hand washing (t(36)=2.92, p<0.01) and 172% greater use within 2 minutes of the use of the water vessel (t(36)=3.51, p = 0.001). We conclude that the loggers were capable of detecting changes in the rates of hand washing with soap and changes in hand washing with soap after use of the toilet. Further adoption of logger technologies would enable more insightful studies of hand washing within urban environments.

Formulation of Antibacterial Liquid Soap from Nyamplung Seed Oil (Calophyllum inophyllum L) with Addition of Curcuma heyneana and its Activity Test on Staphylococcus aureus

NASA Astrophysics Data System (ADS)

Widyaningsih, S.; Chasani, M.; Diastuti, H.; Novayanti

2018-04-01

The increasing demand of soap encourages new innovations of it’s quantity, quality, benefits and raw materials. One of the innovations that has been developed is the use of nyamplung (C. inophyllum L) seed oil as basic ingredients of soap, with addition of active substances such as antibacterial and fragrance. This research aims to determine best formulation of liquid soap according to SNI 06-4085-1996 and its antibacterial activity after addition of n-hexane fraction of C. heyneana rhizome and fragrance from lavender flower oil at various concentrations, then a hedonic test was conducted to evaluate the panelist's preference towards the soap with the best formulation. This research has been done through several stages of soap making with saponification method, soap characterization according to SNI 06-4085-1996, determination of best formulation of liquid soap based on the effectiveness index method and antibacterial activity test of liquid soap to S.aureus with disc diffusion method and hedonic test using some parameters such as colour, odor, foam, clean power and effects after being used. The results showed that the best characteristic soap according to SNI 06-4085-1996 was soap with 0.2% antibacterial content and 2.5% perfume. The best soap characteristic showed total fatty acid 67.49%, free fatty acid 1.01%, neutral fat 7.24%, weight of type 1.05 g/mL, pH of 9.85 and foam stability 76.69%. The results of the antibacterial activity test of the best formula soap showed the inhibitory zone of 14.92 mm.

Performance of Lead-Free versus Lead-Based Hunting Ammunition in Ballistic Soap

PubMed Central

Gremse, Felix; Krone, Oliver; Thamm, Mirko; Kiessling, Fabian; Tolba, René Hany; Rieger, Siegfried; Gremse, Carl

2014-01-01

Background Lead-free hunting bullets are an alternative to lead-containing bullets which cause health risks for humans and endangered scavenging raptors through lead ingestion. However, doubts concerning the effectiveness of lead-free hunting bullets hinder the wide-spread acceptance in the hunting and wildlife management community. Methods We performed terminal ballistic experiments under standardized conditions with ballistic soap as surrogate for game animal tissue to characterize dimensionally stable, partially fragmenting, and deforming lead-free bullets and one commonly used lead-containing bullet. The permanent cavities created in soap blocks are used as a measure for the potential wound damage. The soap blocks were imaged using computed tomography to assess the volume and shape of the cavity and the number of fragments. Shots were performed at different impact speeds, covering a realistic shooting range. Using 3D image segmentation, cavity volume, metal fragment count, deflection angle, and depth of maximum damage were determined. Shots were repeated to investigate the reproducibility of ballistic soap experiments. Results All bullets showed an increasing cavity volume with increasing deposited energy. The dimensionally stable and fragmenting lead-free bullets achieved a constant conversion ratio while the deforming copper and lead-containing bullets showed a ratio, which increases linearly with the total deposited energy. The lead-containing bullet created hundreds of fragments and significantly more fragments than the lead-free bullets. The deflection angle was significantly higher for the dimensionally stable bullet due to its tumbling behavior and was similarly low for the other bullets. The deforming bullets achieved higher reproducibility than the fragmenting and dimensionally stable bullets. Conclusion The deforming lead-free bullet closely resembled the deforming lead-containing bullet in terms of energy conversion, deflection angle, cavity shape

Hand hygiene with soap and water is superior to alcohol rub and antiseptic wipes for removal of Clostridium difficile.

PubMed

Oughton, Matthew T; Loo, Vivian G; Dendukuri, Nandini; Fenn, Susan; Libman, Michael D

2009-10-01

To evaluate common hand hygiene methods for efficacy in removing Clostridium difficile. Randomized crossover comparison among 10 volunteers with hands experimentally contaminated by nontoxigenic C. difficile. Interventions included warm water with plain soap, cold water with plain soap, warm water with antibacterial soap, antiseptic hand wipes, alcohol-based handrub, and a control involving no intervention. All interventions were evaluated for mean reduction in colony-forming units (CFUs) under 2 contamination protocols: "whole hand" and "palmar surface." Results were analyzed according to a Bayesian approach, by using hierarchical models adjusted for multiple observations. Under the whole-hand protocol, the greatest adjusted mean reductions were achieved by warm water with plain soap (2.14 log(10) CFU/mL [95% credible interval (CrI), 1.74-2.54 log(10) CFU/mL]), cold water with plain soap (1.88 log(10) CFU/mL [95% CrI, 1.48-2.28 log(10) CFU/mL), and warm water with antibacterial soap (1.51 log(10) CFU/mL [95% CrI, 1.12-1.91 log(10) CFU/mL]), followed by antiseptic hand wipes (0.57 log(10) CFU/mL [95% CrI, 0.17-0.96 log(10) CFU/mL]). Alcohol-based handrub (0.06 log(10) CFU/mL [95% CrI, -0.34 to 0.45 log(10) CFU/mL]) was equivalent to no intervention. Under the palmar surface protocol, warm water with plain soap, cold water with plain soap, and warm water with antibacterial soap again yielded the greatest mean reductions, followed by antiseptic hand wipes (26.6, 26.6, 26.6, and 21.9 CFUs per plate, respectively), when compared with alcohol-based handrub. Hypothenar (odds ratio, 10.98 [95% CrI, 1.96-37.65]) and thenar (odds ratio, 6.99 [95% CrI, 1.25-23.41]) surfaces were more likely than fingertips to remain heavily contaminated after handwashing. Handwashing with soap and water showed the greatest efficacy in removing C. difficile and should be performed preferentially over the use of alcohol-based handrubs when contact with C. difficile is suspected or likely.

Topological phases of topological-insulator thin films

NASA Astrophysics Data System (ADS)

Asmar, Mahmoud M.; Sheehy, Daniel E.; Vekhter, Ilya

2018-02-01

We study the properties of a thin film of topological insulator material. We treat the coupling between helical states at opposite surfaces of the film in the properly-adapted tunneling approximation, and show that the tunneling matrix element oscillates as a function of both the film thickness and the momentum in the plane of the film for Bi2Se3 and Bi2Te3 . As a result, while the magnitude of the matrix element at the center of the surface Brillouin zone gives the gap in the energy spectrum, the sign of the matrix element uniquely determines the topological properties of the film, as demonstrated by explicitly computing the pseudospin textures and the Chern number. We find a sequence of transitions between topological and nontopological phases, separated by semimetallic states, as the film thickness varies. In the topological phase, the edge states of the film always exist but only carry a spin current if the edge potentials break particle-hole symmetry. The edge states decay very slowly away from the boundary in Bi2Se3 , making Bi2Te3 , where this scale is shorter, a more promising candidate for the observation of these states. Our results hold for free-standing films as well as heterostructures with large-gap insulators.

Tunneling decay of false vortices

NASA Astrophysics Data System (ADS)

Lee, Bum-Hoon; Lee, Wonwoo; MacKenzie, Richard; Paranjape, M. B.; Yajnik, U. A.; Yeom, Dong-han

2013-10-01

We consider the decay of vortices trapped in the false vacuum of a theory of scalar electrodynamics in 2+1 dimensions. The potential is inspired by models with intermediate symmetry breaking to a metastable vacuum that completely breaks a U(1) symmetry, while in the true vacuum, the symmetry is unbroken. The false vacuum is unstable through the formation of true vacuum bubbles; however, the rate of decay can be extremely long. On the other hand, the false vacuum can contain metastable vortex solutions. These vortices contain the true vacuum inside in addition to a unit of magnetic flux and the appropriate topologically nontrivial false vacuum outside. We numerically establish the existence of vortex solutions which are classically stable; however, they can decay via tunneling. In general terms, they tunnel to a configuration which is a large, thin-walled vortex configuration that is now classically unstable to the expansion of its radius. We compute an estimate for the tunneling amplitude in the semiclassical approximation. We believe our analysis would be relevant to superconducting thin films or superfluids.

New test method for the evaluation of the preservation efficacy of soaps at very alkaline pH made by saponification.

PubMed

Témoin-Fardini, S; Servant, J; Sellam, S

2017-10-01

The aim of this study was to develop a test method to evaluate the preservation efficacy for a specific product, a very high-alkaline liquid soap (pH around 10) made by a saponification process. Several manufacturers have experienced contamination issues with these high-pH soaps despite passing a classic preservative efficacy challenge test or even a multi-inoculation challenge test. Bacteria were isolated from contaminated soaps and were identified using 16S rRNA gene sequencing. High-alkaline-pH unpreserved soaps were tested using the Thor Personal Care internal multichallenge test method (TM206) with classical microorganisms and then with the bacterial strains isolated from various contaminated soaps (TM768). Preservatives were added to these soaps and assessed for their efficacy using the newly developed test. Four different species of bacteria (Nesterenkonia lacusekhoensis, Dermacoccus sp., Halomonas sp. and Roseomonas sp.) were identified by sequencing among the contaminants of the various soaps tested. Among these, only one bacterial species, Nesterenkonia lacusekhoensis, appeared to be responsible for the specific contamination of these high-alkaline soaps. Thus, one specific wild-type strain of Nesterenkonia lacusekhoensis, named as strain 768, was used in a new multi-inoculation test (TM768). Unlike the single inoculation challenge test, the multi-inoculation test using the Nesterenkonia strain 768 was able to predict the sensitivity of a product towards this bacterium. Among the 27 different preservatives tested, 10 were able to protect the formula against contamination with this bacterium. This study enabled the development of a test method to evaluate the efficacy of preservation using a specific bacterium, Nesterenkonia lacusekhoensis, responsible for the contamination of very alkaline soaps made by saponification and identify an appropriate preservative system. © 2017 Society of Cosmetic Scientists and the Société Française de Cosmétologie.

From R&D to end users applications in operational oceanography: The navy's "SOAP" case study

NASA Astrophysics Data System (ADS)

Giraud Saint-Albin, S.; Jourdan, D.

2003-04-01

For the last ten years, the CMO/BRESM has conducted an operational program for Ocean Analysis and Prediction SOAP, whose goal has been to support sea activities with high resolution mesoscale ocean nowcast products. Successive prototypes have been generated, operated and improved in tandem with a continuous re-evaluation of Navy Needs. This strategy played a key-role in defining the concept of “real-time integrated oceanography” which relies on remote and in situ ocean observations, (a hierarchy of) ocean models and data assimilation methods. The paper focuses on the results of the latter feasability study for next SOAP prototype: the military motivation for developing new prototypes is to extend the application domain of SOAP operational products from the operative (~ a description of the synoptic scale) to the tactical ( ~ a tailored product to strategic needs) relevance. Current SOAP P2 system is as a transition system pulled by end-user’s requirements and designed by research oceanographers from existing tools and models. The development of SOAP P3 has just started and will benefit from the emergence of an increasing offer of ocean modelling results, pushed by the GODAE initiative. It will be based on MERCATOR high resolution prototypes. From that starting point future developments will have to address both issues of defense specific requirements for high resolution ocean modeling and computation of relevant acoustical products for military applications. Especially, the crucial needs for assessing the end-users’ products reliability should be explored.

Streakline flow visualization of discrete hole film cooling with holes inclined 30 deg to surface

NASA Technical Reports Server (NTRS)

Colladay, R. S.; Russell, L. M.; Lane, J. M.

1976-01-01

Film injection from three rows of discrete holes angled 30 deg to the surface in line with mainstream flow and spaced 5 diameters apart in a staggered array was visualized by using helium bubbles as tracer particles. Both the main stream and the film injectant were ambient air. Detailed streaklines showing the turbulent motion of the film mixing with the main stream were obtained by photographing small, neutrally buoyant helium-filled soap bubbles which followed the flow field. The ratio of boundary layer thickness to hole diameter and the Reynolds number were typical of gas turbine film cooling applications. The results showed the behavior of the film and its interaction with the main stream for a range of blowing rates and two initial boundary layer thicknesses.

SOAP 2.0: Spot Oscillation And Planet 2.0

NASA Astrophysics Data System (ADS)

Dumusque, Xavier; Boisse, I.; Santos, N. C.

2015-04-01

SOAP (Spot Oscillation And Planet) 2.0 simulates the effects of dark spots and bright plages on the surface of a rotating star, computing their expected radial velocity and photometric signatures. It includes the convective blueshift and its inhibition in active regions.

Reproducible fabrication and applications of superconducting scanning tunneling microscope tips

NASA Astrophysics Data System (ADS)

Naaman, Ofer; Teizer, Winfried; Dynes, Robert C.

2001-03-01

We report on a method developed in our lab, for the fabrication of superconducting scanning tunneling microscope (STM) tips in a reproducible fashion. The fabrication process relies on sequential deposition of superconducting Pb and a proximity-coupled Ag capping layer onto a Pt/Ir tip. The tips were characterized by tunneling into both normal-metal and superconducting films, and the results confirm that the tips are superconducting with Tc and Δ close to that of bulk lead. The lead phonon structure in the tunneling density of states was observed, indicating a single step tunneling process. In an attempt to form STM Josephson junctions, we used our tips to form S/I/S junctions with R_NN ~50-100 kΩ. Results from spectroscopic measurements of these junctions at 2.0 K are discussed within the framework of the Ivanchenko and Zil'berman theory (Soviet Physics JETP, vol.28, 1272; 1969) of Josephson tunneling in the presence of strong phase fluctuations.

Imprint control of BaTiO 3 thin films via chemically induced surface polarization pinning

DOE PAGES

Lee, Hyungwoo; Kim, Tae Heon; Patzner, Jacob J.; ...

2016-02-22

Surface-adsorbed polar molecules can significantly alter the ferroelectric properties of oxide thin films. Thus, fundamental understanding and controlling the effect of surface adsorbates are crucial for the implementation of ferroelectric thin film devices, such as ferroelectric tunnel junctions. Herein, we report an imprint control of BaTiO 3 (BTO) thin films by chemically induced surface polarization pinning in the top few atomic layers of the water-exposed BTO films. Our studies based on synchrotron X-ray scattering and coherent Bragg rod analysis demonstrate that the chemically induced surface polarization is not switchable but reduces the polarization imprint and improves the bistability of ferroelectricmore » phase in BTO tunnel junctions. Here, we conclude that the chemical treatment of ferroelectric thin films with polar molecules may serve as a simple yet powerful strategy to enhance functional properties of ferroelectric tunnel junctions for their practical applications.« less

Isolation of Raoultella planticola from refillable antimicrobial liquid soap dispensers in a dental setting.

PubMed

Momeni, Stephanie S; Tomlin, Nancy; Ruby, John D

2015-04-01

Liquid antimicrobial soaps are commonly used in the dental health care setting for hand washing to minimize the potential spread of infectious agents to health care workers and patients. The purpose of the current study was to evaluate possible bacterial contamination of antimicrobial liquid soap dispensers located in 2 institutional comprehensive dental care clinics. Fourteen soap dispensers and 16 original stock containers were sampled. A 1-milliliter aliquot was diluted in 10 mL of phosphate buffer (Tween-80; Acros). Serial dilutions were plated in duplicate on neutralizing agar and incubated for 7 days. Molecular identification was performed using 500 base pair comparisons of 16S ribosomal ribonucleic acid sequencing. Taq polymerase chain reaction was performed with sequence-specific primers for Raoultella species. Bacterial growth was observed at 18 hours for 57% (8 of 14) of soap dispenser samples. Bacterial densities ranged from 4 × 10(2) to 6 × 10(9) colony-forming units per milliliter. Original commercial containers exhibited no growth. Isolates were identified as Raoultella (Klebsiella) planticola. This is the first study to the authors' knowledge indicating recovery of R. planticola from antimicrobial liquid soap dispensers. R. planticola is a recognized environmental opportunistic pathogen that potentially poses a health concern. These findings indicate compliance problems with infection prevention recommendations and support the US Centers for Disease Control and Prevention's recommendation that dispensers should not be topped off. High bacterial loads of R. planticola are inconsistent with infection control practices and are a concern because transmission and possible infection to the health care worker or the patient may occur. Copyright © 2015 American Dental Association. Published by Elsevier Inc. All rights reserved.

Small-Body Extensions for the Satellite Orbit Analysis Program (SOAP)

NASA Technical Reports Server (NTRS)

Carnright, Robert; Stodden, David; Coggi, John

2008-01-01

An extension to the SOAP software allows users to work with tri-axial ellipsoid-based representations of planetary bodies, primarily for working with small, natural satellites, asteroids, and comets. SOAP is a widely used tool for the visualization and analysis of space missions. The small body extension provides the same visualization and analysis constructs for use with small bodies. These constructs allow the user to characterize satellite path and instrument cover information for small bodies in both 3D display and numerical output formats. Tri-axial ellipsoids are geometric shapes the diameters of which are different in each of three principal x, y, and z dimensions. This construct provides a better approximation than using spheres or oblate spheroids (ellipsoids comprising two common equatorial diameters as a distinct polar diameter). However, the tri-axial ellipsoid is considerably more difficult to work with from a modeling perspective. In addition, the SOAP small-body extensions allow the user to actually employ a plate model for highly irregular surfaces. Both tri-axial ellipsoids and plate models can be assigned to coordinate frames, thus allowing for the modeling of arbitrary changes to body orientation. A variety of features have been extended to support tri-axial ellipsoids, including the computation and display of the spacecraft sub-orbital point, ground trace, instrument footprints, and swathes. Displays of 3D instrument volumes can be shown interacting with the ellipsoids. Longitude/latitude grids, contour plots, and texture maps can be displayed on the ellipsoids using a variety of projections. The distance along an arbitrary line of sight can be computed between the spacecraft and the ellipsoid, and the coordinates of that intersection can be plotted as a function of time. The small-body extension supports the same visual and analytical constructs that are supported for spheres and oblate spheroids in SOAP making the implementation of the more

Soap Operas and Captioning in the EFL Class.

ERIC Educational Resources Information Center

Huffman, Donald T.

A teacher describes the use of closed-caption decoding of television melodramas to teach English as a second language (ESL). The approach uses evening soap operas that afford a range of English usage and accents, realistic dialogue, entertainment, and coverage of current social issues and are closed-captioned for the hearing-impaired. The programs…

5. FOURTH FLOOR, HOTEL SOAP LINES TO NORTHWEST: PRESS (LEFT ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

5. FOURTH FLOOR, HOTEL SOAP LINES TO NORTHWEST: PRESS (LEFT CENTER), MANUAL CUTTERS (CENTER, RIGHT CENTER) - Colgate & Company Jersey City Plant, Building No. B-15, 90-96 Greene Street, Jersey City, Hudson County, NJ

Elastic Measurements of Amorphous Silicon Films at mK Temperatures

NASA Astrophysics Data System (ADS)

Fefferman, Andrew; Maldonado, Ana; Collin, Eddy; Liu, Xiao; Metcalf, Tom; Jernigan, Glenn

2017-06-01

The low-temperature properties of glass are distinct from those of crystals due to the presence of poorly understood low-energy excitations. The tunneling model proposes that these are atoms tunneling between nearby equilibria, forming tunneling two-level systems (TLSs). This model is rather successful, but it does not explain the remarkably universal value of the mechanical dissipation Q^{-1} near 1 K. The only known exceptions to this universality are the Q^{-1} of certain thin films of amorphous silicon, carbon and germanium. Recently, it was found that Q^{-1} of amorphous silicon (a-Si) films can be reduced by two orders of magnitude by increasing the temperature of the substrate during deposition. According to the tunneling model, the reduction in Q^{-1} at 1 K implies a reduction in P0γ 2, where P0 is the density of TLSs and γ is their coupling to phonons. In this preliminary report, we demonstrate elastic measurements of a-Si films down to 20 mK. This will allow us, in future work, to determine whether P0 or γ is responsible for the reduction in Q^{-1} with deposition temperature.

Ultra-pure soft water ameliorates atopic skin disease by preventing metallic soap deposition in NC/Tnd mice and reduces skin dryness in humans.

PubMed

Tanaka, Akane; Matsuda, Akira; Jung, Kyungsook; Jang, Hyosun; Ahn, Ginnae; Ishizaka, Saori; Amagai, Yosuke; Oida, Kumiko; Arkwright, Peter D; Matsuda, Hiroshi

2015-09-01

Mineral ions in tap water react with fatty acids in soap, leading to the formation of insoluble precipitate (metallic soap) on skin during washing. We hypothesised that metallic soap might negatively alter skin conditions. Application of metallic soap onto the skin of NC/Tnd mice with allergic dermatitis further induced inflammation with elevation of plasma immunoglobulin E and proinflammatory cytokine expression. Pruritus and dryness were ameliorated when the back of mice was washed with soap in Ca2+- and Mg2+-free ultra-pure soft water (UPSW). Washing in UPSW, but not tap water, also protected the skin of healthy volunteers from the soap deposition. Furthermore, 4 weeks of showering with UPSW reduced dryness and pruritus of human subjects with dry skin. Washing with UPSW may be therapeutically beneficial in patients with skin troubles.

Lead(ii) soaps: crystal structures, polymorphism, and solid and liquid mesophases.

PubMed

Martínez-Casado, F J; Ramos-Riesco, M; Rodríguez-Cheda, J A; Redondo-Yélamos, M I; Garrido, L; Fernández-Martínez, A; García-Barriocanal, J; da Silva, I; Durán-Olivencia, M; Poulain, A

2017-07-05

The long-chain members of the lead(ii) alkanoate series or soaps, from octanoate to octadecanoate, have been thoroughly characterized by means of XRD, PDF analysis, DSC, FTIR, ssNMR and other techniques, in all their phases and mesophases. The crystal structures at room temperature of all of the members of the series are now solved, showing the existence of two polymorphic forms in the room temperature crystal phase, different to short and long-chain members. Only nonanoate and decanoate present both forms, and this polymorphism is proven to be monotropic. At higher temperature, these compounds present a solid mesophase, defined as rotator, a liquid crystal phase and a liquid phase, all of which have a similar local arrangement. Since some lead(ii) soaps appear as degradation compounds in oil paintings, the solved crystal structures of lead(ii) soaps can now be used as fingerprints for their detection using X-ray diffraction. Pair distribution function analysis on these compounds is very similar in the same phases and mesophases for the different members, showing the same short range order. This observation suggests that this technique could also be used in the detection of these compounds in disordered phases or in the initial stages of formation in paintings.

7. FOURTH FLOOR, DETAIL OF HOTEL SOAP LINE TO WEST: ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

7. FOURTH FLOOR, DETAIL OF HOTEL SOAP LINE TO WEST: FERGUSON & HAAS AUTOMATIC WRAPPING MACHINE INSTALLED BY 1929 - Colgate & Company Jersey City Plant, Building No. B-15, 90-96 Greene Street, Jersey City, Hudson County, NJ

Analysis of a deflating soap bubble

NASA Astrophysics Data System (ADS)

Jackson, David P.; Sleyman, Sarah

2010-10-01

A soap bubble on the end of a cylindrical tube is seen to deflate as the higher pressure air inside the bubble escapes through a tube. We perform an experiment to measure the radius of the slowly deflating bubble and observe that the radius decreases to a minimum before quickly increasing. This behavior reflects the fact that the bubble ends up as a flat surface over the end of the tube. A theoretical analysis reproduces this behavior and compares favorably with the experimental data.

Soaps and germicides as adjunct topical antimycotic agents on candida species implicated in vulvovaginal candidasis.

PubMed

Ogunshe, Adenike A O; Omotoso, Oluwatoyin A; Akindele, Titilayo M

2011-06-01

The study aims at evaluating the potentials of soaps and germicides/disinfectants as adjunct topical anti-vulvovaginal candidasis agents. In vitro inhibitory activities of the test agents, prepared according to the manufacturer's specification for toilet and midwifery purposes were determined using modified agar well-diffusion method. Varied susceptibility patterns were exhibited by Candida albicans (26.5%), C. glabrata (18.4%), C. pseudotropicalis (14.3%) and C. tropicalis (40.8%) implicated in vulvovaginal candidasis, indicating Crusader oil (100%), Meriko (95%), Tetmosol (84.7%) and Aloe (68.4%) as the most inhibitory soaps against the Candida strains. The in vitro inhibitory activities of the germicides and disinfectants ranged between (Dettol; 34.6% and Purit; 84.6%) for C. albicans; (Roberts; 33.3% and Purit; 83.3%) for C. glabrata; (Roberts; 21.4% and Purit; 92.9%) for C. pseudotropicalis; (Dettol; 35.0% and Purit; 87.5%) for C. tropicalis respectively. All the Candida strains were totally inhibited by the germicides and disinfectants at the second lower dilutions, except in Morigad towards C. albicans (69.2%]) C. glabrata (72.2%), C. pseudotropicalis (92.9%) and C. tropicalis (82.5%) but none of the vaginal Lactobacillus strains was inhibited by the soaps, germicides or disinfectant. About 90% of a control group indicated relief after pubic cleansing with soaps, germicides and disinfectants. Results indicatied the safety of soaps, germicides and disinfectants as potential adjunct topical cleansing-agents in cases of vaginal itching and candidasis, a common mucosal infection caused by opportunistic yeasts of the Candida genus.

Environmental monitoring study of linear alkylbenzene sulfonates and insoluble soap in Spanish sewage sludge samples.

PubMed

Cantarero, Samuel; Zafra-Gómez, Alberto; Ballesteros, Oscar; Navalón, Alberto; Reis, Marco S; Saraiva, Pedro M; Vílchez, José L

2011-01-01

In this work we present a monitoring study of linear alkylbenzene sulfonates (LAS) and insoluble soap performed on Spanish sewage sludge samples. This work focuses on finding statistical relations between LAS concentrations and insoluble soap in sewage sludge samples and variables related to wastewater treatment plants such as water hardness, population and treatment type. It is worth to mention that 38 samples, collected from different Spanish regions, were studied. The statistical tool we used was Principal Component Analysis (PC), in order to reduce the number of response variables. The analysis of variance (ANOVA) test and a non-parametric test such as the Kruskal-Wallis test were also studied through the estimation of the p-value (probability of obtaining a test statistic at least as extreme as the one that was actually observed, assuming that the null hypothesis is true) in order to study possible relations between the concentration of both analytes and the rest of variables. We also compared LAS and insoluble soap behaviors. In addition, the results obtained for LAS (mean value) were compared with the limit value proposed by the future Directive entitled "Working Document on Sludge". According to the results, the mean obtained for soap and LAS was 26.49 g kg(-1) and 6.15 g kg(-1) respectively. It is worth noting that LAS mean was significantly higher than the limit value (2.6 g kg(-1)). In addition, LAS and soap concentrations depend largely on water hardness. However, only LAS concentration depends on treatment type.

The Utilization of VCO (Virgin Coconut Oil) in Manufacturing of Solid Soap with Red Betel Leaf Extract Addition (Paper Crotum Ruiz &Pav)

NASA Astrophysics Data System (ADS)

Sari, M.

2018-04-01

Soap is a compound of sodium or potassium with fatty acids from vegetable oils or solid animal fats, soft or liquid, and foamy. Considering the potential of VCO as the raw material for making soap and supported by the benefits of red betel leaves, then this research is done by making solid bath soap from VCO which is supplemented with Red betel leaf extract. The purpose of this research is to make solid soap from VCO with an extract of red betel leaf based on SNINo.06-3532199. Analyzing VCO oil, which is used for the manufacture of soap, consists of analysis of saponification figures, Iodine number and peroxide number. Has made solid soap from VCO oil with Red betel leaf extract. From the five quality standards established under SNI 06-3532-1994 only two quality standards that can be done that is water quality and the amount of acidity. The percent of water quality obtained is 10% meanwhile the amount of acidity obtained is 9,32%. According to the data, it can be concluded that the solid soap made was not fulfill SNI 06-3532-1994.

Toxicity of insecticidal soaps to the Asian citrus psyllid (Diaphorina citri) and two of its natural enemies

USDA-ARS?s Scientific Manuscript database

Insecticidal soaps (hereafter “soaps”) are labeled for use by homeowners and also can be used in citrus grown for the organic market. Soaps control some insect pests and therefore might be an alternative to conventional pesticides for control of the Asian citrus psyllid, Diaphorina citri Kuwayama (...

4. THIRD FLOOR CENTER BAY TO NORTH; SOAP KETTLES TO ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

4. THIRD FLOOR CENTER BAY TO NORTH; SOAP KETTLES TO LEFT AND RIGHT, TWO-STORY TANK AT CENTER REAR - Colgate & Company Jersey City Plant, Building No. B-13, 48-50 Grand Street, Jersey City, Hudson County, NJ

Method of refining cracked oil by using metallic soaps. [desulfurization of cracked oils

DOE Office of Scientific and Technical Information (OSTI.GOV)

Masakichi, M.; Marunouchi, K.K.; Yoshimura, T.

1937-04-13

The method of refining cracked oil consists in dissolving oil-soluble heavy metallic soap of oleic acid in a volatile organic solvent which will disperse homogeneously in cracked oil; pouring the solution thus obtained slowly into cracked oil to effect dispersion naturally and homogeneously at room temperature in the cracked oil. This process serves to react the mercaptans in the cracked oil with the heavy metallic soap by a double decomposition reaction and to precipitate the mercaptans as insoluble metallic salts. The remaining liquid is distilled to separate it from the remaining solvent.

Molecular and electronic structure of thin films of protoporphyrin(IX)Fe(III)Cl

NASA Astrophysics Data System (ADS)

Snyder, Shelly R.; White, Henry S.

1991-11-01

Electrochemical, scanning tunneling microscopy (STM), and tunneling spectroscopy studies of the molecular and electronic properties of thin films of protoporphyrin(IX)Fe(III)Cl (abbreviated as PP(IX)Fe(III)Cl) on highly oriented pyrolytic graphite (HOPG) electrodes are reported. PP(IX)Fe(III)Cl films are prepared by two different methods: (1) adsorption, yielding an electrochemically-active film, and (2) irreversible electrooxidative polymerization, yielding an electrochemically-inactive film. STM images, in conjunction with electro-chemical results, indicate that adsorption of PP(IX)Fe(III)Cl from aqueous solutions onto freshly cleaved HOPG results in a film comprised of molecular aggregates. In contrast, films prepared by irreversible electrooxidative polymerization of PP(IX)Fe(III)Cl have a denser, highly structured morphology, including what appear to be small pinholes (approx. 50A diameter) in an otherwise continuous film.

Efficacy of triclosan as an antimicrobial hand soap and its potential impact on antimicrobial resistance: a focused review.

PubMed

Giuliano, Christopher A; Rybak, Michael J

2015-03-01

Triclosan is a synthetic biocide found in many household products, including antimicrobial hand soap. Levels of triclosan have been found throughout the environment and in human urine, blood, and even breast milk. Increasing levels of exposure to triclosan have led to concerns over the development of resistance to triclosan and cross-resistance to other antimicrobials. We performed a literature search to assess whether the widespread use of triclosan displays a favorable benefit: risk ratio, defined by evaluation of triclosan's efficacy as an antimicrobial hand soap and its potential effect on the development of antimicrobial resistance. Data from laboratory-based studies regarding the efficacy of triclosan are conflicting, although well-designed studies suggest no significant difference in efficacy over nonantimicrobial soap. In addition, when triclosan was introduced in a community setting, no beneficial effects were observed on the reduction of infections over nonantimicrobial soap. Resistance to triclosan and cross-resistance to antimicrobials have been consistently demonstrated in laboratory settings, although overall resistance rates and cross-resistance rates in the community setting are low. Based on the available evidence, the risk of potential antimicrobial resistance outweighs the benefit of widespread triclosan use in antimicrobial soaps. © 2015 Pharmacotherapy Publications, Inc.

Observed practices and perceived advantages of different hand cleansing agents in rural Bangladesh: ash, soil, and soap.

PubMed

Nizame, Fosiul A; Nasreen, Sharifa; Halder, Amal K; Arman, Shaila; Winch, Peter J; Unicomb, Leanne; Luby, Stephen P

2015-06-01

Bangladeshi communities have historically used ash and soil as handwashing agents. A structured observation study and qualitative interviews on the use of ash/soil and soap as handwashing agents were conducted in rural Bangladesh to help develop a handwashing promotion intervention. The observations were conducted among 1,000 randomly selected households from 36 districts. Fieldworkers observed people using ash/soil to wash their hand(s) on 13% of occasions after defecation and on 10% after cleaning a child's anus. This compares with 19% of people who used soap after defecation and 27% after cleaning a child who defecated. Using ash/soil or soap was rarely (< 1%) observed at other times recommended for handwashing. The qualitative study enrolled 24 households from three observation villages, where high usage of ash/soil for handwashing was detected. Most informants reported that ash/soil was used only for handwashing after fecal contact, and that ash/soil could clean hands as effectively as soap. © The American Society of Tropical Medicine and Hygiene.

Tunneling Characteristics Depending on Schottky Barriers and Diffusion Current in SiOC.

PubMed

Oh, Teresa; Kim, Chy Hyung

2016-02-01

To obtain a diffusion current in SiOC, the aluminum doped zinc oxide films were deposited on SiOC/Si wafer by a RF magnetron sputtering. All the X-ray patterns of the SiOC films showed amorphous phases. The level of binding energy of Si atoms will lead to an additional potential modulation by long range Coulombic and covalent interactions with oxygen ions. The growth of the AZO film was affected by the characteristics of SiOC, resulting in similar trends in XPS spectra and a shift to higher AZO lattice d values than the original AZO d values in XRD analyses. The charges trapped by the defects at the interlayer between AZO and SiOC films induced the decreased mobility of carriers. In the absence of trap charges, AZO grown on SiOC film such as the sample prepared at O2 = 25 or 30 sccm, which has low charge carrier concentration and high mobility, showed high mobility in an ambipolar characteristic of oxide semiconductor due to the tunneling effect and diffusion current. The structural matching of an interface between AZO and amorphous SiOC enhanced the height of Schottky Barrier (SB), and then the mobility was increased by the tunneling effect from band to band through the high SB.

MANCHESTER MILLS, PRINT WORKS: BLUE DYE AND SOAPING; PRINTING AND ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

MANCHESTER MILLS, PRINT WORKS: BLUE DYE AND SOAPING; PRINTING AND BLEACHING BUILDINGS. PHOTOCOPY OF c. 1905 VIEW LOOKING NORTHEAST. From the collection of Mr. George Durette, Photographer, Manchester, N. H. - Amoskeag Millyard, Canal Street, Manchester, Hillsborough County, NH

The efficacy of Pistacia Terebinthus soap in the treatment of cetuximab-induced skin toxicity.

PubMed

Tastekin, Didem; Tambas, Makbule; Kilic, Kemal; Erturk, Kayhan; Arslan, Deniz

2014-12-01

This open-labeled phase II, efficacy-finding study evaluated the efficiency and safety of Pistacia terebinthus soap in metastatic colorectal cancer patients who developed cetuximab induced skin toxicity. Patients who received cetuximab plus chemotherapy and developed Grade 2 or 3 skin toxicity were treated twice daily with a soap made of oil extracted from Pistacia terebinthus. During treatment, no topical or oral antibiotics, corticosteroids or other moisturizers were used. Patients were examined 1 week later and their photographs were taken. Fifteen mCRC patients who developed skin toxicity while receiving first-line CTX in combination with chemotherapy were included into the study. Eight patients were male and the median age was 58 (25-70). Sixty percent of the patients (n:9) had Grade 3 skin toxicity. Complete response rates in patients with Grade 2 and Grade 3 skin toxicities were 100 and 33%, respectively. In the remaining patients with Grade 3 toxicity the skin toxicity regressed to Grade 1. The objective response rate was 100%, and no delay, dose reduction or discontinuation of CTX treatment due to skin toxicity was necessary. Skin toxicity reoccurred in all patients when patients stopped administering the soap and therefore they used it throughout the cetuximab treatment. Pistacia terebinthus soap seemed to be used safely and effectively in the treatment of skin toxicity induced by Cetuximab.

Psychosocial Factors Mediating the Effect of the CHoBI7 Intervention on Handwashing With Soap: A Randomized Controlled Trial.

PubMed

George, Christine Marie; Biswas, Shwapon; Jung, Danielle; Perin, Jamie; Parvin, Tahmina; Monira, Shirajum; Saif-Ur-Rahman, K M; Rashid, Mahamud-Ur; Bhuyian, Sazzadul Islam; Thomas, Elizabeth D; Dreibelbis, Robert; Begum, Farzana; Zohura, Fatema; Zhang, Xiaotong; Sack, David A; Alam, Munirul; Sack, R Bradley; Leontsini, Elli; Winch, Peter J

2017-08-01

Inadequate hand hygiene is estimated to result in nearly 300,000 deaths annually, with the majority of deaths being among children younger than 5 years. In an effort to promote handwashing with soap and water treatment behaviors among highly susceptible household members of cholera patients, we recently developed the Cholera-Hospital-Based Intervention-for-7-Days (CHoBI7); chobi means picture in Bengali. This 1-week handwashing with soap and water treatment intervention is delivered by a promoter in the hospital and the home to cholera patients and their household members. In our randomized controlled trial of this intervention, we observed a significant reduction in symptomatic cholera infections during the 1-week intervention period compared to the control arm and sustained high uptake of observed handwashing with soap behaviors up to 12 months postintervention. The aim of the present study was to assess the underlying mechanism of change that led to the high handwashing with soap behavior observed among participants who received the CHoBI7 intervention. Handwashing with soap was measured using 5-hour structured observation, and psychosocial factors were assessed using a structured questionnaire among 170 intervention and 174 control household members enrolled in the CHoBI7 trial. To investigate potential mediators of the CHoBI7 intervention effect, mediation models were performed. Response efficacy was found to mediate the intervention's effect on habit formation for handwashing with soap at the 1-week follow-up, and disgust, convenience, and cholera awareness were mediators of habit maintenance at the 6- to 12-month follow-up. These results support the use of theory-driven approaches for the development and implementation of handwashing with soap interventions.

The Manufacture, Properties, and Testing of Napalm Soaps

DTIC Science & Technology

1943-11-17

prrcltio’n. Tests at 1000C. a.nd 100 p.s,,i. %Inhibitor Induction Addod Pcriod, mins. N one 0 20 Eydroquinone 1 5 duPont #19 1 150 Lecithin 1 SF0 1 45...acetone tends to hydrolyze the soap, liberating more free acid which in turn is removed by the solvent. Table XXIV shows results obtained with a

Metal spintronics: Tunneling spectroscopy in junctions with magnetic and superconducting electrodes

NASA Astrophysics Data System (ADS)

Yang, Hyunsoo

Recent advances in generating, manipulating and detecting spin-polarized electrons and their electrical current make possible entirely new classes of spin-based sensor, logic and storage devices. An important such device is the magnetic tunnel junction (MTJ) which has been under intensive study in recent years: important applications include nonvolatile memory cells for high performance magnetic random access memory (MRAMs), and magnetic field sensors for high density hard disk drive read heads. Many aspects of the tunneling magnetoresistance (TMR) phenomenon are poorly understood although it is clear that the fundamental origin of TMR is the spin-polarization of the tunneling current. Thus, the measurement of the magnitude and sign of the tunneling spin polarization (TSP) is very important to help the further understanding of TMR. Recently, an extremely high TMR value, of up to 350% at room temperature, has been reported in practical MTJ devices. These MTJs are fabricated with highly oriented crystalline MgO(100) tunnel barriers by straightforward magnetron sputter deposition at room temperature. In parallel with this observation, we report extremely high TSP values exceeding 90% from CoFe/MgO tunnel spin injectors. These TSP values rival the highest polarization values previously reported using exotic half-metallic oxide ferromagnets. The spin polarization of electrons extracted from ferromagnetic films can be probed by a variety of techniques. Amongst these techniques, STS is perhaps the most relevant with respect to TMR but until now all measurements have been made with Al superconducting films which have low superconducting transition temperatures (Tc) so that the measurements must be made at temperatures below 400mK. We demonstrate the use of superconducting electrodes formed from NbN which has a much higher Tc (˜16K) than Al. The use of NbN allows measurements of TSP at higher temperatures above 1K. We have observed the phenomenon of Kondo

The Beginner's Guide to Wind Tunnels with TunnelSim and TunnelSys

NASA Technical Reports Server (NTRS)

Benson, Thomas J.; Galica, Carol A.; Vila, Anthony J.

2010-01-01

The Beginner's Guide to Wind Tunnels is a Web-based, on-line textbook that explains and demonstrates the history, physics, and mathematics involved with wind tunnels and wind tunnel testing. The Web site contains several interactive computer programs to demonstrate scientific principles. TunnelSim is an interactive, educational computer program that demonstrates basic wind tunnel design and operation. TunnelSim is a Java (Sun Microsystems Inc.) applet that solves the continuity and Bernoulli equations to determine the velocity and pressure throughout a tunnel design. TunnelSys is a group of Java applications that mimic wind tunnel testing techniques. Using TunnelSys, a team of students designs, tests, and post-processes the data for a virtual, low speed, and aircraft wing.

12. DETAIL OF REMOVED PLODDER (UPPER HALF) FROM HOTEL SOAP ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

12. DETAIL OF REMOVED PLODDER (UPPER HALF) FROM HOTEL SOAP LINE No. 6 STORED IN G BLOCK (HAER No. NJ-71-NN) - Colgate & Company Jersey City Plant, Building No. B-14, 54-58 Grand Street, Jersey City, Hudson County, NJ

13. DETAIL OF REMOVED PLODDER (LOWER HALF) FROM HOTEL SOAP ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

13. DETAIL OF REMOVED PLODDER (LOWER HALF) FROM HOTEL SOAP LINE No. 6 STORED IN G BLOCK (HAER No. NJ-71-NN) - Colgate & Company Jersey City Plant, Building No. B-14, 54-58 Grand Street, Jersey City, Hudson County, NJ

Removal of Escherichia coli and Enterococcus faecalis after Hand Washing with Antimicrobial and Nonantimicrobial Soap and Persistence of These Bacteria in Rinsates.

PubMed

Pérez-Garza, J; García, S; Heredia, N

2017-10-01

Food handlers are important sources of contamination in the agricultural environment. This study was conducted (i) to evaluate the activity of antimicrobial soaps against Escherichia coli and Enterococcus faecalis using a hand washing model with soiled hands and (ii) to determine the survival and persistence of these bacteria in rinsates. Sterilized agricultural soil from tomato and pepper farms was inoculated with E. coli or E. faecalis at 10 3 or 10 6 CFU/g. Decontaminated hands were placed in contact with contaminated soil for 2 min and were then washed with soaps with or without antimicrobial compounds (citric extracts, chloroxylenol, triclosan, or chlorhexidine gluconate). As the control, hands were washed with sterile distilled water. The levels of bacteria remaining on the hands and recovered from the rinsates were determined using a membrane filtration method and selective media. Antimicrobial soaps removed levels of E. coli similar to those removed by distilled water and nonantimicrobial soap on hands contaminated with E. coli at 10 3 CFU/g. However, when hands were contaminated with E. coli at 10 6 CFU/g, more E. coli was removed with the chlorhexidine gluconate soap. When hands were contaminated with E. faecalis at 10 3 CFU/g, bacteria were removed more effectively with soaps containing chloroxylenol or chlorhexidine gluconate. When hands were contaminated with E. faecalis at 10 6 CFU/g, all of the antimicrobial soaps were more effective for removing the bacteria than were distilled water and nonantimicrobial soap. E. coli grew in all of the hand washing rinsates except that containing triclosan, whereas E. faecalis from the 10 6 CFU/g treatments grew in rinsates containing chlorhexidine gluconate and in the distilled water rinsates. Washing with antimicrobial soap was more effective for reducing bacteria on soiled hands than was washing with water or nonantimicrobial soap. However, persistence or growth of bacteria in these rinsates poses health risks.

Calcium soap from palm fatty acid distillate for ruminant feed: The influence of water temperature

NASA Astrophysics Data System (ADS)

Handojo, Lienda A.; Indarto, Antonius; Shofinita, Dian; Meitha, Anggina; Nabila, Rakhmawati; Triharyogi, Harry; Kevin, Leonardus

2018-03-01

As the largest palm oil producing country in the world, Indonesia also produces abundant amount of Palm Fatty Acid Distillate (PFAD), a by-product of Crude Palm Oil (CPO) refining process. PFAD can be utilized as the raw material for calcium soap, ruminant feed that is widely used to increase milk yield, as well as to increase the ruminant’s fertility. However, the practice of feeding ruminants with calcium soap has not been practiced in Indonesia, which makes it imperative to develop calcium soap production process from PFAD within the country. This research aimed to study the effect of operating conditions of the saponification reaction using PFAD and CaO as reactants on the quality of the calcium soap obtained. The saponification reaction was carried out by modified fusion method. A range of stoichiometric mole ratios of CaO to PFAD (1.0 to 1.6) and the temperature of water (60-90°C) were studied in this research. An increase in the stoichiometric mole ratio of CaO/PFAD was observed to cause a decrease in the acid value, which indicates an increase in the reaction conversion. In contrast, the temperature of water was found to have little impact on the acid value of the product.

The effect of a soap promotion and hygiene education campaign on handwashing behaviour in rural India: a cluster randomised trial.

PubMed

Biran, Adam; Schmidt, Wolf-Peter; Wright, Richard; Jones, Therese; Seshadri, M; Isaac, Pradeep; Nathan, N A; Hall, Peter; McKenna, Joeleen; Granger, Stewart; Bidinger, Pat; Curtis, Val

2009-10-01

To investigate the effectiveness of a hygiene promotion intervention based on germ awareness in increasing handwashing with soap on key occasions (after faecal contact and before eating) in rural Indian households. Cluster randomised trial of a hygiene promotion intervention in five intervention and five control villages. Handwashing was assessed through structured observation in a random sample of 30 households per village. Additionally, soap use was monitored in a sub-sample of 10 households per village using electronic motion detectors embedded in soap bars. The intervention reached 40% of the target population. Germ awareness increased as well as reported handwashing (a possible indicator of perceived social norms). Observed handwashing with soap on key occasions was rare (6%), especially after faecal contact (2%). Observed handwashing with soap on key occasions did not change 4 weeks after the intervention in either the intervention arm (-1%, 95% CI -2%/+0.3%), or the control arm (+0.4%, 95% CI -1%/+2%). Data from motion detectors indicated a significant but small increase in overall soap use in the intervention arm. We cannot confidently identify the nature of this increase except to say that there was no change in a key measure of handwashing after defecation. The intervention proved scalable and effective in raising hygiene awareness. There was some evidence of an impact on soap use but not on the primary outcome of handwashing at key times. However, the results do not exclude that changes in knowledge and social norms may lay the foundations for behaviour change in the longer term.

Nanocluster metal films as thermoelectric material for radioisotope mini battery unit

NASA Astrophysics Data System (ADS)

Borisyuk, P. V.; Krasavin, A. V.; Tkalya, E. V.; Lebedinskii, Yu. Yu.; Vasiliev, O. S.; Yakovlev, V. P.; Kozlova, T. I.; Fetisov, V. V.

2016-10-01

The paper is devoted to studying the thermoelectric and structural properties of films based on metal nanoclusters (Au, Pd, Pt). The experimental results of the study of single nanoclusters' tunneling conductance obtained with scanning tunneling spectroscopy are presented. The obtained data allowed us to evaluate the thermoelectric power of thin film consisting of densely packed individual nanoclusters. It is shown that such thin films can operate as highly efficient thermoelectric materials. A scheme of miniature thermoelectric radioisotope power source based on the thorium-228 isotope is proposed. The efficiency of the radioisotope battery using thermoelectric converters based on nanocluster metal films is shown to reach values up to 1.3%. The estimated characteristics of the device are comparable with the parameters of up-to-date radioisotope batteries based on nickel-63.

Evaluating Sustainability: Soap versus Biodiesel Production from Plant Oils

ERIC Educational Resources Information Center

Pohl, Nicola L. B.; Streff, Jennifer M.; Brokman, Steve

2012-01-01

Herein we describe a series of experiments for the undergraduate organic laboratory curriculum in which various plant oils (soybean, rapeseed, and olive) are subjected to saponification and transesterification reactions to create a set of compounds that can function as soaps or as fuels. The experiments introduce students to and asks them to…

Feasibilty of a Multi-bit Cell Perpendicular Magnetic Tunnel Junction Device

NASA Astrophysics Data System (ADS)

Kim, Chang Soo

The ultimate objective of this research project was to explore the feasibility of making a multi-bit cell perpendicular magnetic tunnel junction (PMTJ) device to increase the storage density of spin-transfer-torque random access memory (STT-RAM). As a first step toward demonstrating a multi-bit cell device, this dissertation contributed a systematic and detailed study of developing a single cell PMTJ device using L10 FePt films. In the beginning of this research, 13 up-and-coming non-volatile memory (NVM) technologies were investigated and evaluated to see whether one of them might outperform NAND flash memories and even HDDs on a cost-per-TB basis in 2020. This evaluation showed that STT-RAM appears to potentially offer superior power efficiency, among other advantages. It is predicted that STTRAM's density could make it a promising candidate for replacing NAND flash memories and possibly HDDs if STTRAM could be improved to store multiple bits per cell. Ta/Mg0 under-layers were used first in order to develop (001) L1 0 ordering of FePt at a low temperature of below 400 °C. It was found that the tradeoff between surface roughness and (001) L10 ordering of FePt makes it difficult to achieve low surface roughness and good perpendicular magnetic properties simultaneously when Ta/Mg0 under-layers are used. It was, therefore, decided to investigate MgO/CrRu under-layers to simultaneously achieve smooth films with good ordering below 400°C. A well ordered 4 nm L10 FePt film with RMS surface roughness close to 0.4 nm, perpendicular coercivity of about 5 kOe, and perpendicular squareness near 1 was obtained at a deposition temperature of 390 °C on a thermally oxidized Si substrate when MgO/CrRu under-layers are used. A PMTJ device was developed by depositing a thin MgO tunnel barrier layer and a top L10 FePt film and then being postannealed at 450 °C for 30 minutes. It was found that the sputtering power needs to be minimized during the thin MgO tunnel barrier

Draft Genome Sequences of Klebsiella oxytoca Isolates Originating from a Highly Contaminated Liquid Hand Soap Product.

PubMed

Hammerl, J A; Lasch, P; Nitsche, A; Dabrowski, P W; Hahmann, H; Wicke, A; Kleta, S; Al Dahouk, S; Dieckmann, R

2015-07-23

In 2013, contaminated liquid soap was detected by routine microbiological monitoring of consumer products through state health authorities. Because of its high load of Klebsiella oxytoca, the liquid soap was notified via the European Union Rapid Alert System for Dangerous Non-Food Products (EU-RAPEX) and recalled. Here, we present two draft genome sequences and a summary of their general features. Copyright © 2015 Hammerl et al.

SOAP-V: Introducing a method to empower medical students to be change agents in bending the cost curve.

PubMed

Moser, Eileen M; Huang, Grace C; Packer, Clifford D; Glod, Susan; Smith, Cynthia D; Alguire, Patrick C; Fazio, Sara B

2016-03-01

Medical students must learn how to practice high-value, cost-conscious care. By modifying the traditional SOAP (Subjective-Objective-Assessment-Plan) presentation to include a discussion of value (SOAP-V), we developed a cognitive forcing function designed to promote discussion of high-value, cost-conscious care during patient delivery. The SOAP-V model prompts the student to consider (1) the evidence that supports a test or treatment, (2) the patient's preferences and values, and (3) the financial cost of a test or treatment compared to alternatives. Students report their findings to their teams during patient care rounds. This tool has been successfully used at 3 medical schools. Preliminary results find that students who have been trained in SOAP-V feel more empowered to address the economic healthcare crisis, are more comfortable in initiating discussions about value, and are more likely to consider potential costs to the healthcare system. © 2015 Society of Hospital Medicine.

Mercury and hydroquinone content of skin toning creams and cosmetic soaps, and the potential risks to the health of Ghanaian women.

PubMed

Agorku, Eric Selorm; Kwaansa-Ansah, Edward Ebow; Voegborlo, Ray Bright; Amegbletor, Pamela; Opoku, Francis

2016-01-01

In this study, sixty-two (62) skin-lightening creams and soaps were analysed for total mercury and hydroquinone levels. Total mercury was determined by the Cold Vapour Atomic Absorption Spectrophotometry using an automatic mercury analyser and hydroquinone by High Performance Liquid Chromatography. The mean concentration of total mercury in skin toning creams and cosmetic soaps were 0.098 ± 0.082 and 0.152 ± 0.126 μg/g, respectively. The mean concentration of hydroquinone was 0.243 ± 0.385 and 0.035 ± 0.021 % in skin toning creams and cosmetic soaps, respectively. All the creams and soaps analysed had mercury and hydroquinone levels below the US Food and Drug Administration's acceptable limit of 1 μg/g and 2 %, respectively. The low levels of mercury and hydroquinone in the creams and soaps analysed in this study therefore do not pose any potential risk to consumers who are mostly women in Ghana.

Enhanced voltage-controlled magnetic anisotropy in magnetic tunnel junctions with an MgO/PZT/MgO tunnel barrier

NASA Astrophysics Data System (ADS)

Chien, Diana; Li, Xiang; Wong, Kin; Zurbuchen, Mark A.; Robbennolt, Shauna; Yu, Guoqiang; Tolbert, Sarah; Kioussis, Nicholas; Khalili Amiri, Pedram; Wang, Kang L.; Chang, Jane P.

2016-03-01

Compared with current-controlled magnetization switching in a perpendicular magnetic tunnel junction (MTJ), electric field- or voltage-induced magnetization switching reduces the writing energy of the memory cell, which also results in increased memory density. In this work, an ultra-thin PZT film with high dielectric constant was integrated into the tunneling oxide layer to enhance the voltage-controlled magnetic anisotropy (VCMA) effect. The growth of MTJ stacks with an MgO/PZT/MgO tunnel barrier was performed using a combination of sputtering and atomic layer deposition techniques. The fabricated MTJs with the MgO/PZT/MgO barrier demonstrate a VCMA coefficient, which is ˜40% higher (19.8 ± 1.3 fJ/V m) than the control sample MTJs with an MgO barrier (14.3 ± 2.7 fJ/V m). The MTJs with the MgO/PZT/MgO barrier also possess a sizeable tunneling magnetoresistance (TMR) of more than 50% at room temperature, comparable to the control MTJs with an MgO barrier. The TMR and enhanced VCMA effect demonstrated simultaneously in this work make the MgO/PZT/MgO barrier-based MTJs potential candidates for future voltage-controlled, ultralow-power, and high-density magnetic random access memory devices.

Observed Handwashing with Soap Practices Among Cholera Patients and Accompanying Household Members in a Hospital Setting (CHoBI7 Trial).

PubMed

Zohura, Fatema; Bhuyian, Sazzadul Islam; Monira, Shirajum; Begum, Farzana; Biswas, Shwapon K; Parvin, Tahmina; Sack, David; Sack, R Bradley; Leontsini, Elli; Saif-Ur-Rahman, K M; Rashid, Mahamud-Ur; Sharmin, Rumana; Zhang, Xiaotong; Alam, Munirul; George, Christine Marie

2016-12-07

Household members of cholera patients are at a 100 times higher risk of cholera than the general population. Despite this risk, there are only a handful of studies that have investigated the handwashing practices among hospitalized diarrhea patients and their accompanying household members. To investigate handwashing practices in a hospital setting among this high-risk population, 444 hours of structured observation was conducted in a hospital in Dhaka, Bangladesh, among 148 cholera patients and their household members. Handwashing with soap practices were observed at the following key events: after toileting, after cleaning the anus of a child, after removing child feces, during food preparation, before eating, and before feeding. Spot-checks were also conducted to observe the presence of soap at bathroom areas. Overall, 4% (4/103) of key events involved handwashing with soap among cholera patients and household members during the structured observation period. This was 3% (1/37) among cholera patients and 5% (3/66) for household members. For toileting events, observed handwashing with soap was 7% (3/46) overall, 7% (1/14) for cholera patients, and 6% (2/32) for household members. For food-related events, overall observed handwashing with soap was 2% (2/93 overall), and 0% (0/34) and 3% (2/59) for cholera patients and household members, respectively. Soap was observed at only 7% (4/55) of handwashing stations used by patients and household members during spot-checks. Observed handwashing with soap at key times among patients and accompanying household members was very low. These findings highlight the urgent need for interventions to target this high-risk population. © The American Society of Tropical Medicine and Hygiene.

Determination of insoluble soap in agricultural soil and sewage sludge samples by liquid chromatography with ultraviolet detection.

PubMed

Cantarero, Samuel; Zafra-Gómez, Alberto; Ballesteros, Oscar; Navalón, Alberto; Vílchez, José L; Crovetto, Guillermo; Verge, Coral; de Ferrer, Juan A

2010-11-01

We have developed a new analytical procedure for determining insoluble Ca and Mg fatty acid salts (soaps) in agricultural soil and sewage sludge samples. The number of analytical methodologies that focus in the determination of insoluble soap salts in different environmental compartments is very limited. In this work, we propose a methodology that involves a sample clean-up step with petroleum ether to remove soluble salts and a conversion of Ca and Mg insoluble salts into soluble potassium salts using tripotassium ethylenediaminetetraacetate salt and potassium carbonate, followed by the extraction of analytes from the samples using microwave-assisted extraction with methanol. An improved esterification procedure using 2,4-dibromoacetophenone before the liquid chromatography with ultraviolet detection analysis also has been developed. The absence of matrix effect was demonstrated with two fatty acid Ca salts that are not commercial and are never detected in natural samples (C₁₃:₀ and C₁₇:₀). Therefore, it was possible to evaluate the matrix effect because both standards have similar environmental behavior (adsorption and precipitation) to commercial soaps (C₁₀:₀) to C₁₈:₀). We also studied the effect of the different variables on the clean-up, the conversion of Ca soap, and the extraction and derivatization procedures. The quantification limits found ranged from 0.4 to 0.8 mg/kg. The proposed method was satisfactorily applied for the development of a study on soap behavior in agricultural soil and sewage sludge samples. © 2010 SETAC.

Comparing resonant photon tunneling via cavity modes and Tamm plasmon polariton modes in metal-coated Bragg mirrors.

PubMed

Leosson, K; Shayestehaminzadeh, S; Tryggvason, T K; Kossoy, A; Agnarsson, B; Magnus, F; Olafsson, S; Gudmundsson, J T; Magnusson, E B; Shelykh, I A

2012-10-01

Resonant photon tunneling was investigated experimentally in multilayer structures containing a high-contrast (TiO(2)/SiO(2)) Bragg mirror capped with a semitransparent gold film. Transmission via a fundamental cavity resonance was compared with transmission via the Tamm plasmon polariton resonance that appears at the interface between a metal film and a one-dimensional photonic bandgap structure. The Tamm-plasmon-mediated transmission exhibits a smaller dependence on the angle and polarization of the incident light for similar values of peak transmission, resonance wavelength, and finesse. Implications for transparent electrical contacts based on resonant tunneling structures are discussed.

Is Structured Observation a Valid Technique to Measure Handwashing Behavior? Use of Acceleration Sensors Embedded in Soap to Assess Reactivity to Structured Observation

PubMed Central

Ram, Pavani K.; Halder, Amal K.; Granger, Stewart P.; Jones, Therese; Hall, Peter; Hitchcock, David; Wright, Richard; Nygren, Benjamin; Islam, M. Sirajul; Molyneaux, John W.; Luby, Stephen P.

2010-01-01

Structured observation is often used to evaluate handwashing behavior. We assessed reactivity to structured observation in rural Bangladesh by distributing soap containing acceleration sensors and performing structured observation 4 days later. Sensors recorded the number of times soap was moved. In 45 participating households, the median number of sensor soap movements during the 5-hour time block on pre-observation days was 3.7 (range 0.3–10.6). During the structured observation, the median number of sensor soap movements was 5.0 (range 0–18.0), a 35% increase, P = 0.0004. Compared with the same 5-hour time block on pre-observation days, the number of sensor soap movements increased during structured observation by ≥ 20% in 62% of households, and by ≥ 100% in 22% of households. The increase in sensor soap movements during structured observation, compared with pre-observation days, indicates substantial reactivity to the presence of the observer. These findings call into question the validity of structured observation for measurement of handwashing behavior. PMID:21036840

Is structured observation a valid technique to measure handwashing behavior? Use of acceleration sensors embedded in soap to assess reactivity to structured observation.

PubMed

Ram, Pavani K; Halder, Amal K; Granger, Stewart P; Jones, Therese; Hall, Peter; Hitchcock, David; Wright, Richard; Nygren, Benjamin; Islam, M Sirajul; Molyneaux, John W; Luby, Stephen P

2010-11-01

Structured observation is often used to evaluate handwashing behavior. We assessed reactivity to structured observation in rural Bangladesh by distributing soap containing acceleration sensors and performing structured observation 4 days later. Sensors recorded the number of times soap was moved. In 45 participating households, the median number of sensor soap movements during the 5-hour time block on pre-observation days was 3.7 (range 0.3-10.6). During the structured observation, the median number of sensor soap movements was 5.0 (range 0-18.0), a 35% increase, P = 0.0004. Compared with the same 5-hour time block on pre-observation days, the number of sensor soap movements increased during structured observation by ≥ 20% in 62% of households, and by ≥ 100% in 22% of households. The increase in sensor soap movements during structured observation, compared with pre-observation days, indicates substantial reactivity to the presence of the observer. These findings call into question the validity of structured observation for measurement of handwashing behavior.

Morphology and defect structure of the CeO 2(1 1 1) films grown on Ru(0 0 0 1) as studied by scanning tunneling microscopy

NASA Astrophysics Data System (ADS)

Lu, J.-L.; Gao, H.-J.; Shaikhutdinov, S.; Freund, H.-J.

2006-11-01

The morphology of ceria films grown on a Ru(0 0 0 1) substrate was studied by scanning tunneling microscopy in combination with low-energy electron diffraction and Auger electron spectroscopy. The preparation conditions were determined for the growth of nm-thick, well-ordered CeO 2(1 1 1) films covering the entire surface. The recipe has been adopted from the one suggested by Mullins et al. [D.R. Mullins, P.V. Radulovic, S.H. Overbury, Surf. Sci. 429 (1999) 186] and modified in that significantly higher oxidation temperatures are required to form atomically flat terraces, up to 500 Å in width, with a low density of the point defects assigned to oxygen vacancies. The terraces often consist of several rotational domains. A circular shape of terraces suggest a large variety of undercoordinated sites at the step edges which preferentially nucleate gold particles deposited onto these films. The results show that reactivity studies over ceria and metal/ceria surfaces should be complemented with STM studies, which provide direct information on the film morphology and surface defects, which are usually considered as active sites for catalysis over ceria.

SOAP in Practice: Learning Outcomes of a Cross-Institutional Innovation Project Conducted by Teachers, Student Teachers, and Teacher Educators

ERIC Educational Resources Information Center

Seezink, Audrey; Poell, Rob; Kirschner, Paul

2010-01-01

This paper reports on a case study investigating learning outcomes at the individual and organisational level of a cross-institutional innovation project based on the SOAP approach. SOAP integrates "S"chooling of teachers, "O"rganisational development of schools, "A"ction- and development-oriented research, and…

Guide to resource conservation and cost savings opportunities in the soap, detergents and related products sector

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1998-10-01

This guide was prepared to help those involved in the manufacturing of soap, detergent, and related products to identify potential process improvements that will reduce production costs and conserve resources. The guide offers a series of generic process descriptions and checklists of improvement opportunities specific to each of five major processes used in the industry: Soap production, surfactant production, solid cake product formulation, liquid product formulation, and granulated powdered product formulation. The checklists identify thermal, electrical, environmental, water use, and low- or no-cost measures that can be implemented, as well as retrofit technology options. A variety of new technologies thatmore » may exhibit future potential are also described. Appendices include a glossary, background information on the Ontario soap/detergent industry, and description of the four major categories of ingredients used in the industry.« less

Effect of face washing with soap and water and cleaning with antiseptics on upper-lid bacteria of surgical eye patients.

PubMed

Bekibele, Charles O; Kehinde, Aderemi O; Ajayi, Benedictus G K

2010-12-01

To determine the effect of face washing with soap and water and cleaning with povidone iodine and cetrimide/chlorhexidine gluconate (Savlon) on upper-lid bacteria. Prospective, nonrandomized clinical trial. Eighty patients attending the Eye Clinic, University College Hospital, Ibadan, Nigeria. Eighty patients assigned to 4 groups had swabs of the upper eyelid skin taken before and after face wash with soap and water, and cleansing with Savlon and 5% povidone iodine. Specimens were cultured and Gram stained. Bacterial counts were carried out using standard techniques. Face washing with soap and water increased the proportion of patients with bacterial isolates from 80.0% to 87.5%. The average colony count increased from 187.1 to 318.5 colony units per mL (p = 0.02). Application of 5% povidone iodine without face washing with soap and water reduced the proportion of patients with bacterial isolates from 82.6% (mean count 196.5) to 28.6% (mean count 34.1)(p = 0.001); in comparison, the application of 5% povidone iodine after face washing with soap and water reduced the proportion from 71.4% (mean count 133.9) to 40.0% (mean count 69.0)(p = 0.01). Application of Savlon without face washing with soap and water reduced the proportion of patients with bacterial isolates from 100% (mean count 310.9) to 41.2% (mean count 19.8)(p = 0.004) compared with the application after face washing, which reduced the proportion from 89.5% (mean count 240.3) to 41.2% (mean count 82.9)(p = 0.02). Both povidone and Savlon are effective in reducing periocular bacteria in an African setting. Prior face washing with soap and water had no added benefit in reducing bacterial colony count.

Fabrication and Characteristics of High Capacitance Al Thin Films Capacitor Using a Polymer Inhibitor Bath in Electroless Plating Process.

PubMed

Cho, Young-Lae; Lee, Jung-Woo; Lee, Chang-Hyoung; Choi, Hyung-Seon; Kim, Sung-Su; Song, Young Il; Park, Chan; Suh, Su-Jeong

2015-10-01

An aluminum (Al) thin film capacitor was fabricated for a high capacitance capacitor using electrochemical etching, barrier-type anodizing, and electroless Ni-P plating. In this study, we focused on the bottom-up filling of Ni-P electrodes on Al2O3/Al with etched tunnels. The Al tunnel pits were irregularly distributed on the Al foil, diameters were in the range of about 0.5~1 μm, the depth of the tunnel pits was approximately 35~40 μm, and the complex structure was made full filled hard metal. To control the plating rate, the experiment was performed by adding polyethyleneimine (PEI, C2H5N), a high molecular substance. PEI forms a cross-link at the etching tunnel inlet, playing the role of delaying the inlet plating. When the PEI solution bath was used after activation, the Ni-P layer was deposited selectively on the bottoms of the tunnels. The characteristics were analyzed by adding the PEI addition quantity rate of 100~600 mg/L into the DI water. The capacitance of the Ni-P/Al2O3 (650~700 nm)/Al film was measured at 1 kHz using an impedance/gain phase analyzer. For the plane film without etch tunnels the capacitance was 12.5 nF/cm2 and for the etch film with Ni-P bottom-up filling the capacitance was 92 nF/cm2. These results illustrate a remarkable maximization of capacitance for thin film metal capacitors.

6. 5TH FLOOR, VIEW NORTH OF KETTLE SOAP STORAGE TANKS ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

6. 5TH FLOOR, VIEW NORTH OF KETTLE SOAP STORAGE TANKS (RIGHT) AND WEIGH HOPPERS OVER SITES OF REMOVED AMALGAMATORS (LEFT) - Colgate & Company Jersey City Plant, Building No. B-14, 54-58 Grand Street, Jersey City, Hudson County, NJ

Streakline flow visualization of discrete-hole film cooling with normal, slanted, and compound angle injection

NASA Technical Reports Server (NTRS)

Colladay, R. S.; Russell, L. M.

1976-01-01

Film injection from discrete holes in a three-row, staggered array with five-diameter spacing was studied for three hole angles: (1) normal, (2) slanted 30 deg to the surface in the direction of the main stream, and (3) slanted 30 deg to the surface and 45 deg laterally to the main stream. The ratio of the boundary layer thickness-to-hole diameter and Reynolds number were typical of gas-turbine film-cooling applications. Detailed streaklines showing the turbulent motion of the injected air were obtained by photographing very small neutrally buoyant, helium-filled soap bubbles which follow the flow field.

SOAP 2.0: a tool to estimate the photometric and radial velocity variations induced by stellar spots and plages

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dumusque, X.; Boisse, I.; Santos, N. C., E-mail: xdumusque@cfa.harvard.edu

2014-12-01

This paper presents SOAP 2.0, a new version of the Spot Oscillation And Planet (SOAP) code that estimates in a simple way the photometric and radial velocity (RV) variations induced by active regions. The inhibition of the convective blueshift (CB) inside active regions is considered, as well as the limb brightening effect of plages, a quadratic limb darkening law, and a realistic spot and plage contrast ratio. SOAP 2.0 shows that the activity-induced variation of plages is dominated by the inhibition of the CB effect. For spots, this effect becomes significant only for slow rotators. In addition, in the casemore » of a major active region dominating the activity-induced signal, the ratio between the FWHM and the RV peak-to-peak amplitudes of the cross correlation function can be used to infer the type of active region responsible for the signal for stars with v sin i ≤8 km s{sup –1}. A ratio smaller than three implies a spot, while a larger ratio implies a plage. Using the observation of HD 189733, we show that SOAP 2.0 manages to reproduce the activity variation as well as previous simulations when a spot is dominating the activity-induced variation. In addition, SOAP 2.0 also reproduces the activity variation induced by a plage on the slowly rotating star α Cen B, which is not possible using previous simulations. Following these results, SOAP 2.0 can be used to estimate the signal induced by spots and plages, but also to correct for it when a major active region is dominating the RV variation.« less

A renaissance of soaps? - How to make clear and stable solutions at neutral pH and room temperature.

PubMed

Wolfrum, Stefan; Marcus, Julien; Touraud, Didier; Kunz, Werner

2016-10-01

Soaps are the oldest and perhaps most natural surfactants. However, they lost much of their importance since "technical surfactants", usually based on sulfates or sulfonates, have been developed over the last fifty years. Indeed, soaps are pH- and salt-sensitive and they are irritant, especially to the eyes. In food emulsions, although authorized, they have a bad taste, and long-chain saturated soaps have a high Krafft temperature. We believe that most or perhaps all of these problems can be solved with modern formulation approaches. We start this paper with a short overview of our present knowledge of soaps and soap formulations. Then we focus on the problem of the lacking soap solubility at neutral pH values. For example, it is well known that with the food emulsifier sodium oleate (NaOl), clear and stable aqueous solutions can only be obtained at pH values higher than 10. A decrease in the pH value leads to turbid and unstable solutions. This effect is not compatible with the formulation of aqueous stable and drinkable formulations with neutral or even acidic pH values. However, the pH value/phase behavior of aqueous soap solutions can be altered by the addition of other surfactants. Such a surfactant can be Rebaudioside A (RebA), a steviol glycoside from the plant Stevia rebaudiana which is used as a natural food sweetener. In a recent paper, we showed the influence of RebA on the apKa value of sodium oleate in a beverage microemulsion and on its clearing temperature. In the present paper, we report on the effect of the edible bio-surfactant RebA, on the macroscopic and microscopic phase behavior of simple aqueous sodium oleate solutions at varying pH values. The macroscopic phase behavior is investigated by visual observation and turbidity measurements. The microscopic phase behavior is analyzed by acid-base titration curves, phase-contrast and electron microscopy. It turned out that even at neutral pH, aqueous NaOl/RebA solutions can be completely clear and

Parametric-Studies and Data-Plotting Modules for the SOAP

NASA Technical Reports Server (NTRS)

2008-01-01

"Parametric Studies" and "Data Table Plot View" are the names of software modules in the Satellite Orbit Analysis Program (SOAP). Parametric Studies enables parameterization of as many as three satellite or ground-station attributes across a range of values and computes the average, minimum, and maximum of a specified metric, the revisit time, or 21 other functions at each point in the parameter space. This computation produces a one-, two-, or three-dimensional table of data representing statistical results across the parameter space. Inasmuch as the output of a parametric study in three dimensions can be a very large data set, visualization is a paramount means of discovering trends in the data (see figure). Data Table Plot View enables visualization of the data table created by Parametric Studies or by another data source: this module quickly generates a display of the data in the form of a rotatable three-dimensional-appearing plot, making it unnecessary to load the SOAP output data into a separate plotting program. The rotatable three-dimensionalappearing plot makes it easy to determine which points in the parameter space are most desirable. Both modules provide intuitive user interfaces for ease of use.

Method for producing microcomposite powders using a soap solution

DOEpatents

Maginnis, Michael A.; Robinson, David A.

1996-01-01

A method for producing microcomposite powders for use in superconducting and non-superconducting applications. A particular method to produce microcomposite powders for use in superconducting applications includes the steps of: (a) preparing a solution including ammonium soap; (b) dissolving a preselected amount of a soluble metallic such as silver nitrate in the solution including ammonium soap to form a first solution; (c) adding a primary phase material such as a single phase YBC superconducting material in particle form to the first solution; (d) preparing a second solution formed from a mixture of a weak acid and an alkyl-mono-ether; (e) adding the second solution to the first solution to form a resultant mixture; (f) allowing the resultant mixture to set until the resultant mixture begins to cloud and thicken into a gel precipitating around individual particles of the primary phase material; (g) thereafter drying the resultant mixture to form a YBC superconducting material/silver nitrate precursor powder; and (h) calcining the YBC superconducting material/silver nitrate precursor powder to convert the silver nitrate to silver and thereby form a YBC/silver microcomposite powder wherein the silver is substantially uniformly dispersed in the matrix of the YBC material.